Investigation of electrode materials for alkaline batteries

NASA Technical Reports Server (NTRS)

Arcand, G. M.

1971-01-01

A number of amalgam electrode systems were investigated for possible use as high rate anodes and cathodes. The systems examined include: lithium, sodium, and potassium in Group 1, magnesium, calcium, and barium in Group 2, aluminum in Group 3, lead in Group 4, copper in Group 1b, and zinc and cadmium in Group 2b. The K(Hg) and Na(Hg) anodes in 10 VF and 15 VF (an unambiguous expression of concentration that indicates the number of formula weights of solute dissolved in a liter of solution) hydroxide solutions have proven satisfactory; some of these have produced current densities of more than 8 A/sq cm. None of the amalgam cathodes have approached this performance although the TI(Hg) has delivered 1 A/sq cm. Se(Hg) and Te(Hg) cathodes have given very stable discharges. Zn(Hg) and Cd(Hg) electrodes did not show good high rate characteristics, 200 to 300 mA/sq cm being about the maximum current densities obtainable. Both anodes are charged through a two-step process in which M(Hg) is first formed electrochemically and subsequently reduces Zn(II or Cd(II) to form the corresponding amalgam. The second step is extremely rapid for zinc and very slow for cadmium.

Silicon solar cells as a high-solar-intensity radiometer

NASA Technical Reports Server (NTRS)

Spisz, E. W.; Robson, R. R.

1971-01-01

The characteristics of a conventional, 1- by 2-cm, N/P, gridded silicon solar cell when used as a radiometer have been determined for solar intensity levels to 2800 mW/sq cm (20 solar constants). The short-circuit current was proportional to the radiant intensity for levels only to 700 mW/sq cm (5 solar constants). For intensity levels greater than 700 mW/sq cm, it was necessary to operate the cell in a photoconductive mode in order to obtain a linear relation between the measured current and the radiant intensity. When the solar cell was biased with a reverse voltage of -1 V, the measured current and radiant intensity were linearly related over the complete intensity range from 100 to 2800 mW/sq cm.

SQ10R.

ERIC Educational Resources Information Center

Shaughnessy, Michael F.

1996-01-01

Describes SQ10R, a system of reading hints and strategies similar to SQ3R (that is, survey, question, read, recite, and review). Suggests that SQ10R may be more helpful to developmental students. Briefly describes the system's 12 elements: survey, question, read, reflect, review, repeat, rethink, reintegrate, rehash, renote, rehearse, and reread.…

The magnetospheric currents - An introduction

NASA Technical Reports Server (NTRS)

Akasofu, S.-I.

1984-01-01

It is pointed out that the scientific discipline concerned with magnetospheric currents has grown out from geomagnetism and, in particular, from geomagnetic storm studies. The International Geophysical Year (IGY) introduced a new area for this discipline by making 'man-made satellites' available for the exploration of space around the earth. In this investigation, a brief description is provided of the magnetospheric currents in terms of eight component current systems. Attention is given to the Sq current, the Chapman-Ferraro current, the ring current (the symmetric component), the current systems driven by the solar wind-magnetosphere dynamo (SMD), the cross-tail current system, the average ionospheric current pattern, an example of an instantaneous current pattern, field-aligned currents, and driving mechanisms and models.

SQ109 and PNU-100480 interact to kill Mycobacterium tuberculosis in vitro.

PubMed

Reddy, Venkata M; Dubuisson, Tia; Einck, Leo; Wallis, Robert S; Jakubiec, Wesley; Ladukto, Lynn; Campbell, Sheldon; Nacy, Carol A

2012-05-01

To investigate in vitro interaction between two compounds, SQ109 and PNU-100480, currently in development for the treatment of Mycobacterium tuberculosis (MTB). The two-drug interactions between SQ109 and PNU-100480 and its major metabolite PNU-101603 were assessed by chequerboard titration, and the rate of killing and intracellular activity were determined in both J774A.1 mouse macrophages and whole blood culture. In chequerboard titration, interactions between SQ109 and either oxazolidinone were additive. In time-kill studies, SQ109 killed MTB faster than PNU compounds, and its rate of killing was further enhanced by both oxazolidinones. The order of efficacy of single compounds against intracellular MTB was SQ109 > PNU-100480 > PNU-101603. At sub-MIC, combinations of SQ109 + PNU compounds showed improved intracellular activity over individual drugs; at ≥MIC, the order of efficacy was SQ109 > SQ109 + PNU-100480 > SQ109 + PNU-101603. In whole blood culture, the combined bactericidal activities of SQ109 and PNU-100480 and its major metabolite against intracellular M. tuberculosis did not differ significantly from the sum of the compounds tested individually. SQ109 and PNU combinations were additive and improved the rate of MTB killing over individual drugs. These data suggest that the drugs may work together cooperatively to eliminate MTB in vivo.

Conductance Switching Phenomena and H-Like Aggregates in Squarylium-Dye Langmuir-Blodgett Films

NASA Astrophysics Data System (ADS)

Kushida, Masahito; Inomata, Hisao; Tanaka, Yuichiro; Harada, Kieko; Saito, Kyoichi; Sugita, Kazuyuki

2002-03-01

The current-voltage characteristics of sandwich devices with the structure of top gold electrode/squarylium-dye Langmuir-Blodgett (SQ LB) films/bottom aluminum electrode indicated four kinds of conductivity depending on the evaporation conditions of the top gold electrode. The current densities of two, which showed conductance switching, of the four samples were 30-40 μA/cm2 and 20-30 mA/cm2 in the ON state. In the former case, the dependence of conductance switching voltage on the number of SQ LB films and ultraviolet-visible absorption spectra were studied. The results revealed that conductance switching phenomena were induced at the interface between the top gold electrode and SQ LB films, and caused by the presence of H-like aggregates in SQ LB films.

Climatology of the inter-hemispheric field-aligned currents system over the Nigeria ionosphere

NASA Astrophysics Data System (ADS)

Bolaji, O. S.; Rabiu, A. B.; Oyeyemi, E. O.; Yumoto, K.

2012-11-01

Records of the declination (D) magnetic field data for the year 2009 from the Magnetic Data Acquisition System (MAGDAS) facilities at University of Ilorin were employed for this work. From the minutes value of the D-component, the deduced hourly values of the D-component (Sq(QD)) were used to estimate its diurnal (Sq(D)) values with the most five quietest days identified. The monthly mean (MSq(D)) of the most five quietest days and their seasonal (SSq(D)) variabilities were investigated. The inter-hemispheric field aligned currents (IHFACs) exhibit downward and upward inter-hemispheric field-aligned sheet current that appears as a pair at all local times of the Sq(D), MSq(D), and SSq(D) variations. From these variabilities, the IHFACs were observed to flow from the winter to summer hemisphere during noon and dusk sector and flowing in opposite direction during the dawn sector. The Sq(D) variability patterns that were observed in May, June, August September are gentle compared to the disturbed variabilities in January, February, March and November. The highest positive (˜1.7 arc-min) and negative (˜-2.7 arc min) MSq(D) maxima values were observed in August during the dawn and noon sectors respectively. These values indicated that the IHFACs flow in August is strongly southbound (positive) and northbound (negative) in the dawn and noon sectors respectively. Dusk-side IHFACs as can be observed by MAGDAS are weakly northbound in all the seasons. The direction of IHFACs does not flip at the equinoxes but in June and November and does not become largest at solstices but in August. The IHFACs was observed to exhibit longitudinal variability, which indicated that larger amplitude of winter-to-summer IHFACs is observed to be greater in June solstice (northbound/negative IHFACs) than in the December solstice (southbound/positive IHFACs) during the noon sector.

Sq field characteristics at Phu Thuy, Vietnam, during solar cycle 23: comparisons with Sq field in other longitude sectors

NASA Astrophysics Data System (ADS)

Pham Thi Thu, H.; Amory-Mazaudier, C.; Le Huy, M.

2011-01-01

Quiet days variations in the Earth's magnetic field (the Sq current system) are compared and contrasted for the Asian, African and American sectors using a new dataset from Vietnam. This is the first presentation of the variation of the Earth's magnetic field (Sq), during the solar cycle 23, at Phu Thuy, Vietnam (geographic latitudes 21.03° N and longitude: 105.95° E). Phu Thuy observatory is located below the crest of the equatorial fountain in the Asian longitude sector of the Northern Hemisphere. The morphology of the Sq daily variation is presented as a function of solar cycle and seasons. The diurnal variation of Phu Thuy is compared to those obtained in different magnetic observatories over the world to highlight the characteristics of the Phu Thuy observations. In other longitude sectors we find different patterns. At Phu Thuy the solar cycle variation of the amplitude of the daily variation of the X component is correlated to the F.10.7 cm solar radiation (~0.74). This correlation factor is greater than the correlation factor obtained in two observatories located at the same magnetic latitudes in other longitude sectors: at Tamanrasset in the African sector (~0.42, geographic latitude ~22.79) and San Juan in the American sector (~0.03, geographic latitude ~18.38). At Phu Thuy, the Sq field exhibits an equinoctial and a diurnal asymmetry: - The seasonal variation of the monthly mean of X component exhibits the well known semiannual pattern with 2 equinox maxima, but the X component is larger in spring than in autumn. Depending of the phase of the sunspot cycle, the maximum amplitude of the X component varies in spring from 30 nT to 75 nT and in autumn from 20 nT to 60 nT. The maximum amplitude of the X component exhibits roughly the same variation in both solstices, varying from about ~20 nT to 50 nT, depending on the position into the solar cycle. - In all seasons, the mean equinoctial diurnal Y component has a morning maximum Larger than the afternoon minimum i.e. the equivalent current flow over a day is more southward than northward. During winter, the asymmetry is maximum, it erases the afternoon minimum. At the Gnangara observatory, in Asian Southern Hemisphere, the diurnal Y pattern is opposite and the current flow is more northward. It seems that in the Asian sector, the northern and southern Sq current cells both contribute strongly to the equatorial electrojet. The pattern is different in the African and American sectors where the northern Sq current cell contribution to the equatorial electrojet is smaller than the southern one. These observations can explain the unexpected maximum of amplitude of the equatorial electrojet observed in the Asian sector where the internal field is very large. During winter the Y component flow presents an anomaly, it is always southward during the whole day and there is no afternoon northward circulation.

The application of Dow Chemical's perfluorinated membranes in proton-exchange membrane fuel cells

NASA Technical Reports Server (NTRS)

Eisman, G. A.

1989-01-01

Dow Chemical's research activities in fuel cells revolve around the development of perfluorosulfonic acid membranes useful as the proton transport medium and separator. Some of the performance characteristics which are typical for such membranes are outlined. The results of tests utilizing a new experimental membrane useful in proton-exchange membrane fuel cells are presented. The high voltage at low current densities can lead to higher system efficiencies while, at the same time, not sacrificing other critical properties pertinent to membrane fuel cell operation. A series of tests to determine response times indicated that on-off cycles are on the order of 80 milliseconds to reach 90 percent of full power. The IR free voltage at 100 amps/sq ft was determined and the results indicating a membrane/electrode package resistance to be .15 ohm-sq cm at 100 amps/sq ft.

Annual and semiannual variations of the geomagnetic field at equatorial locations

USGS Publications Warehouse

Campbell, W.H.

1981-01-01

For a year of quiet solar-activity level, geomagnetic records from American hemisphere observatories located between about 0?? and 30?? north geomagnetic latitude were used to compare the annual and semiannual variations of the geomagnetic field associated with three separate contributions: (a) the quiet-day midnight level, MDT; (b) the solar-quiet daily variation, Sq; (c) the quiet-time lunar semidiurnal tidal variation, L(12). Four Fourier spectral constituents (24, 12, 8, 6 h periods) of Sq were individually treated. All three orthogonal elements (H, D and Z) were included in the study. The MDT changes show a dominant semiannual variation having a range of about 7 gammas in H and a dominant annual variation in Z having a range of over 8 gammas. These changes seem to be a seasonal response to the nightside distortions by magnetospheric currents. There is a slow decrease in MDT amplitudes with increasing latitude. The Sq changes follow the patterns expected from an equatorial ionospheric dynamo electrojet current system. The dominant seasonal variations occur in H having a range of over 21 gammas for the 24 h period and over 12 gammas for the 12 h period spectral components. The higher-order components are relatively smaller in size. The Sq(H) amplitudes decrease rapidly with increasing latitude. Magnetospheric contributions to the equatorial Sq must be less than a few per cent of the observed magnitude. The L(12) variation shows the ionospheric electrojet features by the dominance of H and the rapid decrease in amplitude with latitude away from the equator. However, the seasonal variation range of over 7 gammas has a maximum in early February and minimum in late June that is not presently explainable by the known ionospheric conductivity and tidal behavior. ?? 1981.

Incremental Innovation and Progress in Advanced Squamous Cell Lung Cancer: Current Status and Future Impact of Treatment.

PubMed

Langer, Corey J; Obasaju, Coleman; Bunn, Paul; Bonomi, Philip; Gandara, David; Hirsch, Fred R; Kim, Edward S; Natale, Ronald B; Novello, Silvia; Paz-Ares, Luis; Pérol, Maurice; Reck, Martin; Ramalingam, Suresh S; Reynolds, Craig H; Socinski, Mark A; Spigel, David R; Wakelee, Heather; Mayo, Carlos; Thatcher, Nick

2016-12-01

Squamous cell lung cancer (sqCLC) is an aggressive form of cancer that poses many therapeutic challenges. Patients tend to be older, present at a later stage, and have a high incidence of comorbidities, which can compromise treatment delivery and exacerbate toxicity. In addition, certain agents routinely available for nonsquamous cell histologic subtypes, such as bevacizumab and pemetrexed, are contraindicated or lack efficacy in sqCLC. Therapeutic progress has been much slower for advanced sqCLC, with median survival times of approximately 9 to 11 months in most studies. Herein, we discuss the current therapeutic landscape for patients with sqCLC versus with nonsquamous NSCLC. Current evidence indicates that new targeted treatments, notably monoclonal antibodies such as ramucirumab and necitumumab, and immunotherapies such as nivolumab and pembrolizumab can provide survival prolongation, although the benefits are still relatively modest. These incremental improvements, all realized since 2012, in aggregate, will very likely have a clinically meaningful impact for patients with sqCLC. We also discuss recent genomic studies of sqCLC that have identified potentially actionable molecular targets, as well as the relevant targeted agents in clinical development. Finally, we discuss the magnitude of survival benefit and the risk-to-benefit ratio that would prove clinically meaningful in this underserved patient population with unmet needs. Copyright © 2016 International Association for the Study of Lung Cancer. Published by Elsevier Inc. All rights reserved.

Basic coaxial mass driver reference design. [electromagnetic lunar launch

NASA Technical Reports Server (NTRS)

Kolm, H. H.

1977-01-01

The reference design for a basic coaxial mass driver is developed to illustrate the principles and optimization procedures on the basis of numerical integration by programmable pocket calculators. The four inch caliber system uses a single-coil bucket and a single-phase propulsion track with discrete coils, separately energized by capacitors. An actual driver would use multiple-coil buckets and an oscillatory multi-phase drive system. Even the basic, table-top demonstration system should in principle be able to achieve accelerations in the 1,000 m/sq sec range. Current densities of the order of 25 ka/sq cm, continuously achievable only in superconductors, are carried by an ordinary aluminum bucket coil for a short period in order to demonstrate the calculated acceleration. Ultimately the system can be lengthened and provided with a magnetically levitated, superconducting bucket to study levitation dynamics under quasi-steady-state conditions, and to approach lunar escape velocity in an evacuated tube.

Variations of B0 and B1 with the solar quiet Sq-current system and comparison with IRI-2012 model at Ilorin

NASA Astrophysics Data System (ADS)

Bello, S. A.; Abdullah, M.; Hamid, N. S. A.; Yoshikawa, A.; Olawepo, A. O.

2017-07-01

The ionospheric thickness (B0) and shape (B1) are bottomside profile parameters introduced by the International Reference Ionosphere (IRI) model. We have validated these parameters with the latest version of the IRI-2012 model and compared them with the solar quiet of geomagnetic H-component (SqH). The B0, B1 and SqH are calculated from the measurements obtained from digisonde DPS-4 sounder and the Magnetic Data Acquisition System (MAGDAS) magnetometer, respectively at Ilorin (geo latitude 8.50°N, geo longitude 4.68°E, and Magnetic dip 4.1°S) an equatorial station in the African sector. The study was for the year 2010, a year of low solar activity (with 27-day averaged solar index, F10.7 = 80 sfu). The results show that B0 for the entire months was higher during the daytime than during the night time. On the other hand, the magnitude of B1during the daytime period is lower than nighttime values and exhibit oscillatory pattern. By comparing the experimental observations of the profile parameters with the IRI-2012 model prediction, we found that B0 was fairly represented by the IRI model options during the nighttime period while discrepancies exist between the model estimates and the experimental values during the morning till midday. A close agreement exists between the observed B1 values and IRI model options. We observed a positive and significant correlation coefficient between B0 and SqH indicating a plausible relationship between these parameters while a weak and negative correlation coefficient between B1 and SqH was observed. We concluded that the difference in the relationship of SqH and the profile parameters B0 and B1 observed can be attributed to their sensitivity to the electric field which is responsible for the E × B drift which in turn modulate the height of the F2.

Tracing the Roots of Textbook Study Systems: An Extended Historical Perspective. College Reading and Learning Assistance Technical Report 86-02.

ERIC Educational Resources Information Center

Stahl, Norman A.; Henk, William A.

Francis P. Robinson's 1946 text, "Effective Study," first presented his Survey, Question, Read, Recite, and Review (SQ3R) study system, which is held to be the most widely advocated textbook study system. This paper traces the development of the ideas behind the SQ3R. SQ3R's theoretical foundation began with work in…

Latitude-dependent delay in the responses of the equatorial electrojet and Sq currents to X-class solar flares

NASA Astrophysics Data System (ADS)

Nogueira, Paulo A. B.; Abdu, Mangalathayil A.; Souza, Jonas R.; Denardini, Clezio M.; Barbosa Neto, Paulo F.; Serra de Souza da Costa, João P.; Silva, Ana P. M.

2018-01-01

We have analyzed low-latitude ionospheric current responses to two intense (X-class) solar flares that occurred on 13 May 2013 and 11 March 2015. Sudden intensifications, in response to solar flare radiation impulses, in the Sq and equatorial electrojet (EEJ) currents, as detected by magnetometers over equatorial and low-latitude sites in South America, are studied. In particular we show for the first time that a 5 to 8 min time delay is present in the peak effect in the EEJ, with respect that of Sq current outside the magnetic equator, in response to the flare radiation enhancement. The Sq current intensification peaks close to the flare X-ray peak, while the EEJ peak occurs 5 to 8 min later. We have used the Sheffield University Plasmasphere-Ionosphere Model at National Institute for Space Research (SUPIM-INPE) to simulate the E-region conductivity enhancement as caused by the flare enhanced solar extreme ultraviolet (EUV) and soft X-rays flux. We propose that the flare-induced enhancement in neutral wind occurring with a time delay (with respect to the flare radiation) could be responsible for a delayed zonal electric field disturbance driving the EEJ, in which the Cowling conductivity offers enhanced sensitivity to the driving zonal electric field.

The formation and propagation of matrix microcracks in cross-ply laminates during static loading

NASA Technical Reports Server (NTRS)

Liu, Siulie; Nairn, John A.

1992-01-01

Experimental results on a wide variety of composite material systems and cross-ply layups of generic type (0 m/90 n)s are described. The microcrack density was measured as a function of applied load for five graphite fiber composite systems. The measured microcracking fracture toughnesses are: 240 J/sq m for Hercules AS4/3501-6, 690 J/sq m for Fiberite 934/T300, 960 J/sq m for DuPont Avimid K Polymer IM6, 1800 to 2400 J/sq m for Fiberite 977-2/T300, and 3000 J/sq m for ICI PEEK/AS4. These data are found to be in good agreement with predictions of the energy release rate analysis (Nairn, 1989).

Cycling Performance of the Iron-Chromium Redox Energy Storage System

NASA Technical Reports Server (NTRS)

Gahn, R. F.; Hagedorn, N. H.; Johnson, J. A.

1985-01-01

Extended charge-discharge cycling of this electrochemical storage system at 65 C was performed on 14.5 sq cm single cells and a four cell, 867 sq cm bipolar stack. Both the anolyte and catholyte reactant fluids contained 1 molar concentrations of iron and chromium chlorides in hydrochloric acid and were separated by a low-selectivity, cation-exchange membrane. The effect of cycling on the chromium electrode and the cation-exchange membrane was determined. Bismuth and bismuth-lead catalyzed chromium electrodes and a radiation-grafted polyethylene membrane were evaluated by cycling between 5 and 85 percent state-of-charge at 80 mA/sq cm and by periodic charge-discharge polarization measurements to 140 mA/sq cm. Gradual performance losses were observed during cycling but were recoverable by completely discharging the system. Good scale-up to the 867 sq cm stack was achieved. The only difference appeared to be an unexplained resistive-type loss which resulted in a 75 percent W-hr efficiency (at 80 mA/sq cm versus 81 percent for the 14.5 sq cm cell). A new rebalance cell was developed to maintain reactant ionic balance. The cell successfully reduced ferric ions in the iron reactant stream to ferrous ions while chloride ions were oxidized to chlorine gas.

Cycling performance of the iron-chromium redox energy storage system

NASA Technical Reports Server (NTRS)

Gahn, R. F.; Hagedorn, N. H.; Johnson, J. A.

1985-01-01

Extended charge-discharge cycling of this electrochemical storage system at 65 C was performed on 14.5 sq cm single cells and a four cell, 867 sq cm bipolar stack. Both the anolyte and catholyte reactant fluids contained 1 molar concentrations of iron and chromium chlorides in hydrochloric acid and were separated by a low-selectivity, cation-exchange membrane. The effect of cycling on the chromium electrode and the cation-exchange membrane was determined. Bismuth and bismuth-lead catalyzed chromium electrodes and a radiation-grafted polyethylene membrane were evaluated by cycling between 5 and 85 percent state-of-charge at 80 mA/sq cm and by periodic charge-discharge polarization measurements to 140 mA/sq cm. Gradual performance losses were observed during cycling but were recoverable by completely discharging the system. Good scale-up to the 867 sq cm stack was achieved. The only difference appeared to be an unexplained resistive-type loss which resulted in a 75 percent W-hr efficiency (at 80 mA/sq cm versus 81 percent for the 14.5 sq cm cell). A new rebalance cell was developed to maintain reactant ionic balance. The cell successfully reduced ferric ions in the iron reactant stream to ferrous ions while chloride ions were oxidized to chlorine gas.

Revealing charge carrier dynamics in squaraine:[6, 6]-phenyl-C 71-butyric acid methyl ester based organic solar cells

NASA Astrophysics Data System (ADS)

Rana, Aniket; Sharma, Chhavi; Prabhu, Deepak D.; Kumar, Mahesh; Karuvath, Yoosaf; Das, Suresh; Chand, Suresh; Singh, Rajiv K.

2018-04-01

Ultrafast charge carrier dynamics as well as the generation of polaron pair in squaraine (SQ) and squaraine:[6,6]-phenyl-C 71-butyric acid methyl ester (SQ:PCBM71) have been studied using ultrafast transient absorption spectroscopy (UTAS). The current study reveals that the pure SQ exhibits the creation of singlet and triplet states; however, incorporation of PCBM71 in SQ results in the formation of polaron pairs with ˜550ps lifetime, which in turn leads to the creation of free electrons in the device. We show that the considerable increment in monomolecular and bimolecular recombination in SQ:PCBM71 compared to pure SQ which describes the interfacial compatibility of SQ and PCBMC71 molecules. The present work not only provides the information about the carrier generation in SQ and SQ:PCBM71 but also gives the facts relating to the effect of PCBM71 mixing into the SQ which is very significant because the SQ has donor-acceptor-donor (D-A-D) structure and mixing one more acceptor can introduce more complex recombinations in the blend. These findings have been complimented by the charge transport study in the device using impedance spectroscopy. The various important transport parameters are transit time (τt), diffusion constant (Dn), global mobility (μ) and carrier lifetime (τr). The values of these parameters are 26.38 μs, 4.64x10-6 cm2s-1, 6.12x10-6 cm2V-1s-1 and 399 μs, respectively. To the best of our knowledge such study related to SQ is not present in the literature comprehensively.

Characteristics of Seasonal Variation and Solar Activity Dependence of the Geomagnetic Solar Quiet Daily Variation

NASA Astrophysics Data System (ADS)

Shinbori, Atsuki; Koyama, Yukinobu; Nosé, Masahito; Hori, Tomoaki; Otsuka, Yuichi

2017-10-01

Characteristics of seasonal variation and solar activity dependence of the X and Y components of the geomagnetic solar quiet (Sq) daily variation at Memambetsu in midlatitudes and Guam near the equator have been investigated using long-term geomagnetic field data with 1 h time resolution from 1957 to 2016. The monthly mean Sq variation in the X and Y components (Sq-X and Sq-Y) shows a clear seasonal variation and solar activity dependence. The amplitude of seasonal variation increases significantly during high solar activities and is proportional to the solar F10.7 index. The pattern of the seasonal variation is quite different between Sq-X and Sq-Y. The result of the correlation analysis between the solar F10.7 index and the Sq-X and Sq-Y shows an almost linear relationship, but the slope of the linear fitted line varies as a function of local time and month. This implies that the sensitivity of Sq-X and Sq-Y to the solar activity is different for different local times and seasons. The pattern of the local time and seasonal variations of Sq-Y at Guam shows good agreement with that of a magnetic field produced by interhemispheric field-aligned currents (FACs), which flow from the summer to winter hemispheres in the dawn and dusk sectors and from the winter to summer hemispheres in the prenoon to afternoon sectors. The direction of the interhemispheric FAC in the dusk sector is opposite to the concept of Fukushima's model.

High efficiency organic photovoltaic cells based on a vapor deposited squaraine donor

NASA Astrophysics Data System (ADS)

Wang, Siyi; Mayo, Elizabeth I.; Perez, M. Dolores; Griffe, Laurent; Wei, Guodan; Djurovich, Peter I.; Forrest, Stephen R.; Thompson, Mark E.

2009-06-01

2,4-bis[4-(N ,N-diisobutylamino)-2,6-dihydroxyphenyl] squaraine (SQ) is used as a donor material in vapor deposited organic heterojunction photovoltaic cells. Devices with the structure indium tin oxide/SQ (x)/C60 (400Å)/bathocuproine (100Å)/Al (1000Å), where x =65, 110, 150, and 200Å were compared. Devices with x =65Å exhibited a power conversion efficiency of 3.1% under 1sun, AM1.5G simulated solar irradiation, giving an open circuit voltage of 0.76±0.01V, a short circuit current of 7.01±0.05mA/cm2, and a fill factor of 0.56±0.05. Thicker SQ films lead to lower short circuit currents and fill factors, giving conversion efficiencies in the range of 2.6% to 3.2%. The demonstration of sublimable SQ as a donor material opens up a family of compounds for use in small molecule based heterojunction photovoltaics.

The Empathy and Systemizing Quotient: The Psychometric Properties of the Dutch Version and a Review of the Cross-Cultural Stability.

PubMed

Groen, Y; Fuermaier, A B M; Den Heijer, A E; Tucha, O; Althaus, M

2015-09-01

The 'Empathy Quotient' (EQ) and 'Systemizing Quotient' (SQ) are used worldwide to measure people's empathizing and systemizing cognitive styles. This study investigates the psychometric properties of the Dutch EQ and SQ in healthy participants (n = 685), and high functioning males with autism spectrum disorder (n = 42). Factor analysis provided support for three subscales of the abridged 28-item EQ: Cognitive Empathy, Emotional Empathy and Social Skills. Overall, the Dutch EQ and SQ appeared reliable and valid tools to assess empathizing and systemizing cognitive style in healthy adults and high functioning adults with autism. The literature showed good cross-cultural stability of the SQ and EQ in Western countries, but in Asian countries EQ is less stable and less sensitive to sex differences.

Are systemizing and autistic traits related to talent and interest in mathematics and engineering? Testing some of the central claims of the empathizing-systemizing theory.

PubMed

Morsanyi, Kinga; Primi, Caterina; Handley, Simon J; Chiesi, Francesca; Galli, Silvia

2012-11-01

In two experiments, we tested some of the central claims of the empathizing-systemizing (E-S) theory. Experiment 1 showed that the systemizing quotient (SQ) was unrelated to performance on a mathematics test, although it was correlated with statistics-related attitudes, self-efficacy, and anxiety. In Experiment 2, systemizing skills, and gender differences in these skills, were more strongly related to spatial thinking styles than to SQ. In fact, when we partialled the effect of spatial thinking styles, SQ was no longer related to systemizing skills. Additionally, there was no relationship between the Autism Spectrum Quotient (AQ) and the SQ, or skills and interest in mathematics and mechanical reasoning. We discuss the implications of our findings for the E-S theory, and for understanding the autistic cognitive profile. ©2011 The British Psychological Society.

Liquid belt radiator design study

NASA Technical Reports Server (NTRS)

Teagan, W. P.; Fitzgerald, K. F.

1986-01-01

The Liquid Belt Radiator (LBR) is an advanced concept developed to meet the needs of anticipated future space missions. A previous study documented the advantages of this concept as a lightweight, easily deployable alternative to present day space heat rejection systems. The technical efforts associated with this study concentrate on refining the concept of the LBR as well as examining the issues of belt dynamics and potential application of the LBR to intermediate and high temperature heat rejection applications. A low temperature point design developed in previous work is updated assuming the use of diffusion pump oil, Santovac-6, as the heat transfer media. Additional analytical and design effort is directed toward determining the impact of interface heat exchanger, fluid bath sealing, and belt drive mechanism designs on system performance and mass. The updated design supports the earlier result by indicating a significant reduction in system specific system mass as compared to heat pipe or pumped fluid radiator concepts currently under consideration (1.3 kg/sq m versus 5 kg/sq m).

Electron transfer capacity dependence of quinone-mediated Fe(III) reduction and current generation by Klebsiella pneumoniae L17.

PubMed

Li, Xiaomin; Liu, Liang; Liu, Tongxu; Yuan, Tian; Zhang, Wei; Li, Fangbai; Zhou, Shungui; Li, Yongtao

2013-06-01

Quinone groups in exogenous electron shuttles can accelerate extracellular electron transfer (EET) from bacteria to insoluble terminal electron acceptors, such as Fe(III) oxides and electrodes, which are important in biogeochemical redox processes and microbial electricity generation. However, the relationship between quinone-mediated EET performance and electron-shuttling properties of the quinones remains incompletely characterized. This study investigates the effects of a series of synthetic quinones (SQs) on goethite reduction and current generation by a fermenting bacterium Klebsiella pneumoniae L17. In addition, the voltammetric behavior and electron transfer capacities (ETCs) of SQ, including electron accepting (EAC) and donating (EDC) capacities, is also examined using electrochemical methods. The results showed that SQ can significantly increase both the Fe(III) reduction rates and current outputs of L17. Each tested SQ reversibly accepted and donated electrons as indicated by the cyclic voltammograms. The EAC and EDC results showed that Carmine and Alizarin had low relative capacities of electron transfer, whereas 9,10-anthraquinone-2,6-disulfonic acid (AQDS), 2-hydroxy-1,4-naphthoquinone (2-HNQ), and 5-hydroxy-1,4-naphthoquinone (5-HNQ) showed stronger relative ETC, and 9,10-anthraquinone-2-carboxylic acid (AQC) and 9,10-anthraquinone-2-sulfonic acid (AQS) had high relative ETC. Enhancement of microbial goethite reduction kinetics and current outputs by SQ had a good linear relationship with their ETC, indicating that the effectiveness of quinone-mediated EET may be strongly dependent on the ETC of the quinones. Therefore, the presence of quinone compounds and fermenting microorganisms may increase the diversity of microbial populations that contribute to element transformation in natural environments. Moreover, ETC determination of different SQ would help to evaluate their performance for microbial EET under anoxic conditions. Copyright © 2013 Elsevier Ltd. All rights reserved.

76 FR 32269 - Federal Property Suitable as Facilities To Assist the Homeless

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-03

... (roads and hwy) and utilities easements, asbestos and lead base paint identified most current use... Status: Unutilized Comments: 39108 sq. ft., presence of asbestos, most recent use-- Electronic Research...: Unutilized Comments: 13199 sq. ft., presence of asbestos, most recent use-- Electronic Research Lab Bldg. 248...

Develop and test fuel cell powered on-site integrated total energy systems. Phase 3: Full-scale power plant development

NASA Technical Reports Server (NTRS)

Feigenbaum, H.; Kaufman, A.; Wang, C. L.; Werth, J.; Whelan, J. A.

1983-01-01

Operating experience with a 5kW methanol-air integrated system is described. On-going test results for a 24-cell, two-sq ft (4kW) stack are reported. The main activity for this stack is currently the evaluation of developmental non-metalic cooling plates. Single-cell test results are presented for a promising developmental cathode catalyst.

Solar array synthesis computer program

NASA Technical Reports Server (NTRS)

Faith, T. J.

1973-01-01

Photovoltaic characteristics have been measured on solar cells irradiated by 1 MeV electrons to fluences ranging from 1 x 10 to the 13th power e/sq cm to 1 x 10 to the 16th power e/sq cm, for cell temperatures ranging from 123 K to 473 K and for illumination intensities ranging from 5m W/sq cm to 1830m W/sq cm. Empirical equations have been derived from these measurements to describe the behavior of light generated current, open circuit voltage and I-V curve shape over various portions of these temperature/illumination ranges. Both 10 ohms/cm and 17 ohms/cm n-p silicon solar cells were tested, and similar analytical expressions were formulated for easy comparison between the two resistivities.

Electrical and Luminescent Properties of Color-Changeable Organic Electroluminescent Diode Using Squarylium Dyes

NASA Astrophysics Data System (ADS)

Mori, Tatsuo; Miyachi, Kiyokazu; Kichimi, Tomoaki; Mizutani, Teruyoshi

1994-12-01

The organic electoluminescent diode (LED) with squarylium (Sq) dye-doped Alq3 changes color upon application of voltage (current). The luminescent color from the organic LED changes from red (electroluminescence (EL) of Sq dye) at low voltage to light green (EL of Alq3) at high voltage. We studied the EL efficiency and EL spectrum of organic Sq-doped Alq3 LED with various doping positions in the emission layer. Consequentially, it was clarified that Sq doping near TPD considerably reduced the EL efficiency. The EL mechanism of the organic LED was concluded to be associated with the energy transfer from the excited Alq3 to the guest dye and hole trapping of the guest dye in Alq3.

The Begun Center for Violence Prevention Research and Education at Case Western Reserve University

ERIC Educational Resources Information Center

Flannery, Daniel J.; Singer, Mark I.

2015-01-01

Established in the year 2000, the Begun Center for Violence Prevention Research and Education is a multidisciplinary center located at a school of social work that engages in collaborative, community-based research and evaluation that spans multiple systems and disciplines. The Center currently occupies 4,200 sq. ft. with multiple offices and…

Status and applicability of solid polymer electrolyte technology to electrolytic hydrogen and oxygen production

NASA Technical Reports Server (NTRS)

Titterington, W. A.

1973-01-01

The solid polymer electrolyte (SPE) water electrolysis technology is presented as a potential energy conversion method for wind driven generator systems. Electrolysis life and performance data are presented from laboratory sized single cells (7.2 sq in active area) with high cell current density selected (1000 ASF) for normal operation.

The interhemispheric and F region dynamo currents revisited with the Swarm constellation

NASA Astrophysics Data System (ADS)

Lühr, Hermann; Kervalishvili, Guram; Michaelis, Ingo; Rauberg, Jan; Ritter, Patricia; Park, Jaeheung; Merayo, Jose M. G.; Brauer, Peter

2015-05-01

Based on magnetic field data sampled by the Swarm satellite constellation it is possible for the first time to determine uniquely F region currents at low latitudes. Initial results are presented from the first 200 days of formation flight (17 April to 5 November 2014). Detailed results have been obtained for interhemispheric field-aligned currents connecting the solar quiet day magnetic variation (Sq) current systems in the two hemispheres. We obtain prominent currents from the Southern (winter) Hemisphere to the Northern around noon. Weaker currents in opposite direction are observed during morning and evening hours. Furthermore, we could confirm the existence of vertical currents above the dip equator, downward around noon and upward around sunset. For both current systems we present and discuss longitudinal variations.

Woven TPS Enabling Missions Beyond Heritage Carbon Phenolic

NASA Technical Reports Server (NTRS)

Stackpoole, Mairead; Venkatapathy, Ethiraj; Feldman, Jay

2013-01-01

Woven Thermal Protection Systems (WTPS) is a new TPS concept that is funded by NASAs Office of the Chief Technologist (OCT) Game Changing Division. The WTPS project demonstrates the potential for manufacturing many TPS architectures capable of performances demanded by the many potential solar system exploration missions. Currently, missions that encounter heat fluxes in the range of 1500 4000 W/sq cm and pressures greater than 1.5 atm have very limited TPS options - only one proven material, fully dense Carbon Phenolic, is currently available for these missions. However, fully dense carbon phenolic is only mass efficient at heat fluxes greater than 4000 W/sq cm, and current mission designs suffer this mass inefficiency for lack of an alternative mid-density TPS. WTPS not only bridges this TPS gap but also offers a replacement for carbon phenolic, which itself requires a significant and costly redevelopment effort to re-establish its capability for use in the high heat flux missions recently prioritized in the NRC Decadal survey, including probe missions to Venus, Saturn and Neptune. This presentation will introduce some woven TPS architectures considered in this project and summarize some recent arc jet testing to evaluate the performance of fully dense and mid density WTPS. Performance comparisons to heritage carbon phenolic will be drawn where applicable.

76 FR 78294 - Federal Property Suitable as Facilities to Assist the Homeless

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-16

... asbestos and lead base paint 10 Bldgs. Redstone Arsenal Redstone Arsenal AL 35898 Landholding Agency: Army..., 1405A, 1406, 1406A Comments: off-site removal only; possible asbestos and lead base paint; sq. ft...-100 sq. ft.; current use: storage to base exchange; need repairs; possible asbestos Suitable/Available...

Spindt cold cathode electron gun development program

NASA Technical Reports Server (NTRS)

Spindt, C. A.

1983-01-01

A thin film field emission cathode array and an electron gun based on this emitter array are summarized. Fabricating state of the art cathodes for testing at NASA and NRL, advancing the fabrication technology, developing wedge shaped emitters, and performing emission tests are covered. An anistropic dry etching process (reactive ion beam etching) developed that leads to increasing the packing density of the emitter tips to about 5 x 10 to the 6th power/square cm. Tests with small arrays of emitter tips having about 10 tips has demonstrated current densities of over 100 A/sq cm. Several times using cathodes having a packing density of 1.25 x 10 to the 6th power tips/sq cm. Indications are that the higher packing density achievable with the dry etch process may extend this capability to the 500 A/sq cm range and beyond. The wedge emitter geometry was developed and shown to produce emission. This geometry can (in principle) extend the current density capability of the cathodes beyond the 500 A/sq cm level. An emission microscope was built and tested for use with the cathodes.

Development of an advanced static feed water electrolysis module. [for spacecraft

NASA Technical Reports Server (NTRS)

Schubert, F. H.; Wynveen, R. A.; Jensen, F. C.; Quattrone, P. D.

1975-01-01

A Static Feed Water Electrolysis Module (SFWEM) was developed to produce 0.92 kg/day (2.0 lb/day) of oxygen (O2). Specific objectives of the program's scope were to (1) eliminate the need for feed water cavity degassing, (2) eliminate the need for subsystem condenser/separators, (3) increase current density capability while decreasing electrolysis cell power (i.e., cell voltage) requirements, and (4) eliminate subsystem rotating parts and incorporate control and monitor instrumentation. A six-cell, one-man capacity module having an active area of 0.00929 sq m (0.10 sq ft) per cell was designed, fabricated, assembled, and subjected to 111 days (2664 hr) of parametric and endurance testing. The SFWEM was successfully operated over a current density range of 0 to 1076 mA/sq cm (0 to 1000 ASF), pressures of ambient to 2067 kN/sq m (300 psia), and temperatures of ambient to 366 K (200 F). During a 94-day endurance test, the SFWEM successfully demonstrated operation without the need for feed water compartment degassing.

Wheat production in controlled environments

NASA Technical Reports Server (NTRS)

Salisbury, Frank B.; Bugbee, Bruce; Bubenheim, David

1987-01-01

Conditions are optimized for maximum yield and quality of wheat to be used in a controlled environment life support system (CELSS) in a Lunar or Martian base or a spacecraft. With yields of 23 to 57 g/sq m/d of edible biomass, a minimum size for a CELSS would be between 12 and 30 sq m per person, utilizing about 600 W/sq m of electrical energy for artificial light. Temperature, irradiance, photoperiod, carbon dioxide levels, humidity, and wind velocity are controlled in growth chambers. Nutrient solutions (adjusted for wheat) are supplied to the roots via a recirculating system that controls pH by adding HNO3 and controlling the NO3/NH4 ratio in solution. A rock-wool plant support allows direct seeding and densities up to 10,000 plants sq m. Densities up to 2000 plants/sq m appear to increase seed yield. Biomass production increases almost linearily with increasing irradiance from 400 to 1700 micromol/sq m/s of photosynthetic photon flux, but the efficiency of light utilization decreases over this range. Photoperiod and temperature both have a profound influence on floral initiation, spikelet formation, stem elongation, and fertilization.

A 2.2 sq m /24 sq ft/ self-controlled deployable heat pipe radiator - Design and test

NASA Technical Reports Server (NTRS)

Edelstein, F.

1975-01-01

An all heat pipe, deployable radiator has been developed which can effectively control pumped fluid loop temperatures under varying loads using variable conductance panel heat pipes. The 2.2 sq m (24 sq ft) aluminum panel can be coupled to either a fluid header or a flexible heat pipe header capable of transporting 850 watts in a 90-deg bent configuration. Test results support the feasibility of using this system to passively control Freon-21 loop temperatures.

SOAR versus SQ3R: A Test of Two Study Systems

ERIC Educational Resources Information Center

Jairam, Dharma; Kiewra, Kenneth A.; Rogers-Kasson, Sarah; Patterson-Hazley, Melissa; Marxhausen, Kim

2014-01-01

Although researchers have long investigated ways to improve study habits and raise achievement, few studies compare study strategy systems with one another. No study to date has compared the long popular SQ3R (Survey, Question, Read, Recite, Review) system with the more modern SOAR (Select, Organize, Associate, Regulate) system. This study…

Examining protein-lipid interactions in model systems with a new squarylium fluorescent dye.

PubMed

Ioffe, Valeriya M; Gorbenko, Galyna P; Tatarets, Anatoliy L; Patsenker, Leonid D; Terpechnig, Ewald A

2006-07-01

The applicability of newly synthesized squarylium dye Sq to probing the changes in physical characteristics of lipid bilayer on the formation of protein-lipid complexes has been evaluated. Lipid vesicles composed of zwitterionic phospholipid phosphatidylcholine (PC) and its mixtures with positively charged detergent cetyltrimethylammonium bromide (CTAB), anionic phospholipid cardiolipin (CL), and cholesterol (Chol) were employed as lipid component of model membrane systems while protein constituent was represented by lysozyme (Lz). Fluorescence intensity of Sq was found to decrease on Lz association with lipid bilayer. This effect was observed in all kinds of model systems suggesting that Sq is sensitive to modification of lipid bilayer physical properties on hydrophobic protein-lipid interactions. It was found that Sq spectral response to variations in Chol content depends on relative contributions of electrostatic and hydrophobic components of Lz-membrane binding.

Endurance Test and Evaluation of Alkaline Water Electrolysis Cells

NASA Technical Reports Server (NTRS)

Kovach, Andrew J.; Schubert, Franz H.; Chang, B. J.; Larkins, Jim T.

1985-01-01

The overall objective of this program is to assess the state of alkaline water electrolysis cell technology and its potential as part of a Regenerative Fuel Cell System (RFCS) of a multikilowatt orbiting powerplant. The program evaluates the endurance capabilities of alkaline electrolyte water electrolysis cells under various operating conditions, including constant condition testing, cyclic testing and high pressure testing. The RFCS demanded the scale-up of existing cell hardware from 0.1 sq ft active electrode area to 1.0 sq ft active electrode area. A single water electrolysis cell and two six-cell modules of 1.0 sq ft active electrode area were designed and fabricated. The two six-cell 1.0 sq ft modules incorporate 1.0 sq ft utilized cores, which allow for minimization of module assembly complexity and increased tolerance to pressure differential. A water electrolysis subsystem was designed and fabricated to allow testing of the six-cell modules. After completing checkout, shakedown, design verification and parametric testing, a module was incorporated into the Regenerative Fuel Cell System Breadboard (RFCSB) for testing at Life Systems, Inc., and at NASA JSC.

Temperature, illumination, and fluence dependence of current and voltage in electron irradiated solar cells

NASA Technical Reports Server (NTRS)

Faith, T. J.; Obenschain, A. F.

1974-01-01

Empirical equations have been derived from measurements of solar cell photovoltaic characteristics relating light-generated current and open circuit voltage to cell temperature, intensity of illumination and 1-MeV electron fluence. Both 2-ohm-cm and 10-ohm-cm cells were tested over the temperature range from 120 to 470 K, the illumination intensity range from 5 to 1830 mW/sq cm, and the electron fluence range from 1 x 10 to the 13th to 1 x 10 to the 16th electrons/sq cm. The normalized temperature coefficient of the light generated current varies as the 0.18 power of the fluence for temperatures above approximately 273 K and is independent of fluence at lower temperatures. At 140 mW/sq cm, a power law expression was derived which shows that the light-generated current decreases at a rate proportional to the 0.153 power of the fluence for both resistivities. The coefficient of the expression is larger for 2-ohm-cm cells; consequently, the advantage for 10-ohm-cm cells increased with increasing fluence.

Investigation of the Stability and 1.0 MeV Proton Radiation Resistance of Commercially Produced Hydrogenated Amorphous Silicon Alloy Solar Cells

NASA Technical Reports Server (NTRS)

Lord, Kenneth R., II; Walters, Michael R.; Woodyard, James R.

1994-01-01

The radiation resistance of commercial solar cells fabricated from hydrogenated amorphous silicon alloys is reported. A number of different device structures were irradiated with 1.0 MeV protons. The cells were insensitive to proton fluences below 1E12 sq cm. The parameters of the irradiated cells were restored with annealing at 200 C. The annealing time was dependent on proton fluence. Annealing devices for one hour restores cell parameters for fluences below 1E14 sq cm fluences above 1E14 sq cm require longer annealing times. A parametric fitting model was used to characterize current mechanisms observed In dark I-V measurements. The current mechanism were explored with irradiation fluence, and voltage and light soaking times. The thermal generation current density and quality factor increased with proton fluence. Device simulation shows the degradation in cell characteristics may be explained by the reduction of the electric field in the intrinsic layer.

Organic Bistable Memory Switching Phenomena in Squarylium-Dye Langmuir-Blodgett Films

NASA Astrophysics Data System (ADS)

Kushida, Masahito; Inomata, Hisao; Miyata, Hiroshi; Harada, Kieko; Saito, Kyoichi; Sugita, Kazuyuki

2003-06-01

We have investigated the relationship between the switching phenomena and H-like aggregates in squarylium-dye Langmuir-Blodgett (SQ LB) films. The current-voltage characteristics of SQ LB films sandwiched between the top gold electrode and the bottom aluminum electrode indicated conductance switching phenomena below the temperature of 100°C but not at 140°C. Current densities suddenly increased at switching voltages between 2 and 4 V. The switching voltage increased as the temperature increased between room temperature and 100°C. Current densities were 50-100 μA/cm2 in a low-impedance state (ON state). A high-impedance state (OFF state) can be recovered by applying a reverse bias, and therefore, these bistable devices are ideal for memory applications. The dependence of conductance switching phenomena and ultraviolet-visible absorption spectra on annealing temperatures was studied. The results revealed that conductance switching phenomena were caused by the presence of H-like aggregates in the SQ LB films.

Fully Printed High-Frequency Phased-Array Antenna on Flexible Substrate

NASA Technical Reports Server (NTRS)

Chen, Yihong; Lu, Xuejun

2010-01-01

To address the issues of flexible electronics needed for surface-to-surface, surface-to-orbit, and back-to-Earth communications necessary for manned exploration of the Moon, Mars, and beyond, a room-temperature printing process has been developed to create active, phased-array antennas (PAAs) on a flexible Kapton substrate. Field effect transistors (FETs) based on carbon nanotubes (CNTs), with many unique physical properties, were successfully proven feasible for phased-array antenna systems. The carrier mobility of an individual CNT is estimated to be at least 100,000 sq cm/V(dot)s. The CNT network in solution has carrier mobility as high as 46,770 sq cm/V(dot)s, and has a large current-density carrying capacity of approx. 1,000 mA/sq cm , which corresponds to a high carrying power of over 2,000 mW/ sq cm. Such high carrier mobility, and large current carrying capacity, allows the achievement of high-speed (>100 GHz), high-power, flexible electronic circuits that can be monolithically integrated on NASA s active phasedarray antennas for various applications, such as pressurized rovers, pressurized habitats, and spacesuits, as well as for locating beacon towers for lunar surface navigation, which will likely be performed at S-band and attached to a mobile astronaut. A fully printed 2-bit 2-element phasedarray antenna (PAA) working at 5.6 GHz, incorporating the CNT FETs as phase shifters, is demonstrated. The PAA is printed out at room temperature on 100-mm thick Kapton substrate. Four CNT FETs are printed together with microstrip time delay lines to function as a 2-bit phase shifter. The FET switch exhibits a switching speed of 0.2 ns, and works well for a 5.6-GHz RF signal. The operating frequency is measured to be 5.6 GHz, versus the state-of-the-art flexible FET operating frequency of 52 MHz. The source-drain current density is measured to be over 1,000 mA/sq cm, while the conventional organic FETs, and single carbon nanotube-based FETs, are typically in the mA to mA/sq cm range. The switching voltage used is 1.8 V, while the state-of-the-art flexible FET has a gate voltage around 50 V. The gate voltage can effectively control the source-drain current with an ON-OFF ratio of over 1,000 obtained at a low Vds bias of 1.8 V. The azimuth steering angles of PAA are measured at 0deg, -14.5deg, -30deg, and 48.6deg. The measured far-field patterns agree well with simulation results. The efficiency of the 2-bit 2-element PAA is measured to be 39 percent, including the loss of transmission line, FET switch, and coupling loss of RF probes. With further optimization, the efficiency is expected to be around 50-60 percent.

Superconducting gravity gradiometer for space and terrestrial applications

NASA Technical Reports Server (NTRS)

Moody, M. V.; Chan, H. A.; Paik, H. J.

1986-01-01

A three-axis superconducting gravity gradiometer with a potential sensitivity better than Eotvos per sq root Hz is currently under development for applications in space. Although such a high sensitivity may be needed for only a limited number of terrestrial applications, superconductivity offers many extraordinary effects which can be used to obtain a gravity gradiometer with other characteristics necessary for operation in a hostile moving-base environment. Utilizing a number of recently devised techniques which rely on certain properties of superconductors, a design for a sensitive yet rugged gravity gradiometer with a high degree of stability and a common-mode rejection ratio greater than 10 to the 9th is produced. With a base line of 0.11 m, a sensitivity of 0.1 Eotvos per sq root Hz is expected in an environment monitored to a level of 0.01 m/sq sec sq root Hz for linear vibration and 7 x 10 to the -6th rad/s sq root Hz for angular vibration. A conventional stabilized platform can be used at this level. The intrinsic noise level, which is two orders of magnitude lower, could be achieved by monitoring the attitude with a superconducting angular accelerometer which is under development. In addition, the new gradiometer design has the versatility of adapting the instrument to different gravity biases by adjusting stored dc currents.

The Systemic Sclerosis Questionnaire (SySQ): Validation of the translation of the original German version into Spanish and its relationship to the disease and to quality of life.

PubMed

Cruz-Domínguez, Maria Pilar; Casarrubias-Ramírez, Moisés; Gasca-Martínez, Victor; Maldonado García, Cindy; Carranza-Muleiro, Rosa Angélica; Medina, Gabriela; García-Collinot, Grettel; Montes-Cortes, Daniel Hector

2017-12-11

Translation, transculturation and validity of the self-administered questionnaire for functionality (Systemic Sclerosis Questionnaires [SySQ]) for use in Spanish patients with systemic sclerosis and its relationship to the severity of the disease and to quality of life. We conducted an observational analytical study to perform a cross-cultural validation of the self-administered questionnaire on functionality in scleroderma. The validity of the form and content was evaluated by an expert panel. The method included: a) adaptation into Spanish of the construct for translation and back translation, and transculturation; b) internal consistency with the SySQ (Cronbach's alpha), and c) reproducibility was assessed taking into account all occasions in which the test was performed with Cohen's kappa. Additionally, we calculated the Spearman correlation coefficient with the Medsger severity scale, Health Assessment Questionnaire score and SF-36 score. We included 70 patients with systemic sclerosis: age 17-78 (51±12) years, 65 (93%) were women, diffuse/limited subtype 64/36%, disease duration of 0.5-40 years. Optimal internal consistency for all categories of the final version of SySQ (Cronbach's α of 0.961) and intraobserver reliability in 2 tests over a 2-week interval (Cohen's kappa coefficient 0.618) and optimal interobserver reliability in 2 tests on the same day (Cohen's kappa coefficient 0.911). Moderate correlation between functionality by SySQ and by Health Assessment Questionnaire (r=0.573, P<.0001). Inverse correlation between SySQ and quality of life mental health domain SF-36 (r=-0.435, P<.001) and physical domain SF-36 (r=-0.638, P<.001). Medsger severity scale (tendon, heart, lung, vascular) also showed significant correlation with SySQ. SySQ in this validated Spanish version is a suitable instrument to measure functional status in patients with systemic sclerosis. Reduced functionality is related to greater tendon and peripheral vascular involvement and to a poorer quality of life. Copyright © 2017 Elsevier España, S.L.U. and Sociedad Española de Reumatología y Colegio Mexicano de Reumatología. All rights reserved.

The correlation between brain gray matter volume and empathizing and systemizing quotients in healthy children.

PubMed

Sassa, Yuko; Taki, Yasuyuki; Takeuchi, Hikaru; Hashizume, Hiroshi; Asano, Michiko; Asano, Kohei; Wakabayashi, Akio; Kawashima, Ryuta

2012-05-01

The abilities to empathize and to systemize, two fundamental dimensions of cognitive style, are characterized by apparent individual differences. These abilities are typically measured using an empathizing quotient (EQ) and a systemizing quotient (SQ) questionnaire, respectively. The purpose of this study was to reveal any correlations between EQ and SQ scores and regional gray matter volumes in healthy children by applying voxel-based morphometry to magnetic resonance images. We collected MRIs of brain structure and administered children's versions of the EQ and SQ questionnaires (EQ-C and SQ-C, respectively) to 261 healthy children aged 5-15 years. Structural MRI data were segmented, normalized, and smoothed using an optimized voxel-based morphometric analysis. Next, we analyzed the correlation between regional gray matter volume and EQ-C and SQ-C scores adjusting for age, sex, and intracranial volume. The EQ-C scores showed significant positive correlations with the regional gray matter volumes of the left fronto-opercular and superior temporal cortices, including the precentral gyrus, the inferior frontal gyrus, the superior temporal gyrus, and the insula, which are functionally related to empathic processing. Additionally, SQ-C scores showed a significant negative correlation with the regional gray matter volume of the left posterior parietal cortex, which is functionally involved in selective attention processing. Our findings suggest that individual differences in cognitive style pertaining to empathizing or systemizing abilities could be explained by differences in the volume of brain structures that are functionally relevant to empathizing and systemizing. Copyright © 2012 Elsevier Inc. All rights reserved.

Large area, low cost solar cell development and production readiness

NASA Technical Reports Server (NTRS)

Michaels, D.

1982-01-01

A process sequence for a large area ( or = 25 sq. cm) silicon solar cell was investigated. Generic cell choice was guided by the expected electron fluence, by the packing factors of various cell envelope designs onto each panel to provide needed voltage as well as current, by the weight constraints on the system, and by the cost goals of the contract.

Generation of the displacement current by the transformation of J-aggregates in spreading monolayers of squarylium dye

NASA Astrophysics Data System (ADS)

Iwamoto, Mitsumasa; Majima, Yutaka; Hirayama, Fuminori; Furuki, Makoto; Pu, Lyong Sun

1992-07-01

Maxwell displacement currents generated from monolayers of squarylium dye with propyl groups (SQ) and from mixed monolayers with arachidic acid were investigated during the course of monolayer compression in connection with the formation of J-aggregates in the monolayers. Abrupt changes in the generation of displacement current were observed for monolayers of SQ due to the transformation between two types of J-aggregates with different absorption spectra. In contrast, for mixed monolayers with arachidic acid which show no transition of J-aggregates, abrupt changes in the displacement current were not observed. It was concluded that displacement current measurement is effective in the detection of the transformation of the molecular arrangement in aggregates.

MR Imaging-based Semi-quantitative Methods for Knee Osteoarthritis

PubMed Central

JARRAYA, Mohamed; HAYASHI, Daichi; ROEMER, Frank Wolfgang; GUERMAZI, Ali

2016-01-01

Magnetic resonance imaging (MRI)-based semi-quantitative (SQ) methods applied to knee osteoarthritis (OA) have been introduced during the last decade and have fundamentally changed our understanding of knee OA pathology since then. Several epidemiological studies and clinical trials have used MRI-based SQ methods to evaluate different outcome measures. Interest in MRI-based SQ scoring system has led to continuous update and refinement. This article reviews the different SQ approaches for MRI-based whole organ assessment of knee OA and also discuss practical aspects of whole joint assessment. PMID:26632537

Development of Thermal Protection Materials for Future Mars Entry, Descent and Landing Systems

NASA Technical Reports Server (NTRS)

Cassell, Alan M.; Beck, Robin A. S.; Arnold, James O.; Hwang, Helen; Wright, Michael J.; Szalai, Christine E.; Blosser, Max; Poteet, Carl C.

2010-01-01

Entry Systems will play a crucial role as NASA develops the technologies required for Human Mars Exploration. The Exploration Technology Development Program Office established the Entry, Descent and Landing (EDL) Technology Development Project to develop Thermal Protection System (TPS) materials for insertion into future Mars Entry Systems. An assessment of current entry system technologies identified significant opportunity to improve the current state of the art in thermal protection materials in order to enable landing of heavy mass (40 mT) payloads. To accomplish this goal, the EDL Project has outlined a framework to define, develop and model the thermal protection system material concepts required to allow for the human exploration of Mars via aerocapture followed by entry. Two primary classes of ablative materials are being developed: rigid and flexible. The rigid ablatives will be applied to the acreage of a 10x30 m rigid mid L/D Aeroshell to endure the dual pulse heating (peak approx.500 W/sq cm). Likewise, flexible ablative materials are being developed for 20-30 m diameter deployable aerodynamic decelerator entry systems that could endure dual pulse heating (peak aprrox.120 W/sq cm). A technology Roadmap is presented that will be used for facilitating the maturation of both the rigid and flexible ablative materials through application of decision metrics (requirements, key performance parameters, TRL definitions, and evaluation criteria) used to assess and advance the various candidate TPS material technologies.

Monolithic Solid Oxide Fuel Cell development

NASA Technical Reports Server (NTRS)

Myles, K. M.; Mcpheeters, C. C.

1989-01-01

The Monolithic Solid Oxide Fuel Cell (MSOFC) is an oxide-ceramic structure in which appropriate electronic and ionic conductors are fabricated in a honeycomb shape similar to a block of corrugated paperboard. These electronic and ionic conductors are arranged to provide short conduction paths to minimize resistive losses. The power density achievable with the MSOFC is expected to be about 8 kW/kg or 4 kW/L, at fuel efficienceis over 50 percent, because of small cell size and low resistive losses in the materials. The MSOFC operates in the range of 700 to 1000 C, at which temperatures rapid reform of hydrocarbon fuels is expected within the nickel-YSZ fuel channels. Tape casting and hot roll calendering are used to fabricate the MSOFC structure. The performance of the MSOFC has improved significantly during the course of development. The limitation of this system, based on materials resistance alone without interfacial resistances, is 0.093 ohm-sq cm area-specific resistance (ASR). The current typical performance of MSOFC single cells is characterized by ASRs of about 0.4 to 0.5 ohm-sq cm. With further development the ASR is expected to be reduced below 0.2 ohm-sq cm, which will result in power levels greater than 1.4 W/sq cm. The feasibility of the MSOFC concept was proven, and the performance was dramatically improved. The differences in thermal expansion coefficients and firing shrinkages among the fuel cell materials were minimized. As a result of good matching of these properties, the MSOFC structure was successfully fabricated with few defects, and the system shows excellent promise for development into a practical power source.

InP Tunnel Junctions for InP/InGaAs Tandem Solar Cells

NASA Technical Reports Server (NTRS)

Vilela, M. F.; Medelci, N.; Bensaoula, A.; Freundlich, A.; Renaud, P.

1995-01-01

We report, for the first time, an epitaxially grown InP p(+)/n(++) tunnel junction. A diode with peak current densities up to 1600 Al/sq cm and maximum specific resistivities (Vp/lp - peak voltage to peak current ratio) in the range of 10(exp -4)Om sq cm is obtained. This peak current density is comparable to the highest results previously reported for lattice matched In(0.53)Ga(0.47)As tunnel junctions. Both results were obtained using chemical beam epitaxy (CBE). In this paper we discuss the electrical characteristics of these tunnel diodes and how the growth conditions influence them.

On the electromagnetic fields, Poynting vector, and peak power radiated by lightning return strokes

NASA Technical Reports Server (NTRS)

Krider, E. P.

1992-01-01

The initial radiation fields, Poynting vector, and total electromagnetic power that a vertical return stroke radiates into the upper half space have been computed when the speed of the stroke, nu, is a significant fraction of the speed of light, c, assuming that at large distances and early times the source is an infinitesimal dipole. The initial current is also assumed to satisfy the transmission-line model with a constant nu and to be perpendicular to an infinite, perfectly conducting ground. The effect of a large nu is to increase the radiation fields by a factor of (1-beta-sq cos-sq theta) exp -1, where beta = nu/c and theta is measured from the vertical, and the Poynting vector by a factor of (1-beta-sq cos-sq theta) exp -2.

4-Nitro styrylquinoline is an antimalarial inhibiting multiple stages of Plasmodium falciparum asexual life cycle.

PubMed

Roberts, Bracken F; Zheng, Yongsheng; Cleaveleand, Jacob; Lee, Sukjun; Lee, Eunyoung; Ayong, Lawrence; Yuan, Yu; Chakrabarti, Debopam

2017-04-01

Drugs against malaria are losing their effectiveness because of emerging drug resistance. This underscores the need for novel therapeutic options for malaria with mechanism of actions distinct from current antimalarials. To identify novel pharmacophores against malaria we have screened compounds containing structural features of natural products that are pharmacologically relevant. This screening has identified a 4-nitro styrylquinoline (SQ) compound with submicromolar antiplasmodial activity and excellent selectivity. SQ exhibits a cellular action distinct from current antimalarials, acting early on malaria parasite's intraerythrocytic life cycle including merozoite invasion. The compound is a fast-acting parasitocidal agent and also exhibits curative property in the rodent malaria model when administered orally. In this report, we describe the synthesis, preliminary structure-function analysis, and the parasite developmental stage specific action of the SQ scaffold. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

A model of BIS/BAS sensitivity, emotion regulation difficulties, and depression, anxiety, and stress symptoms in relation to sleep quality.

PubMed

Markarian, Shaunt A; Pickett, Scott M; Deveson, Danielle F; Kanona, Brenda B

2013-11-30

Recent research has indicated that interactions between behavioral inhibition system (BIS)/behavioral activation system (BAS) sensitivity and emotion regulation (ER) difficulties increases risk for psychopathology. Considering sleep quality (SQ) has been linked to emotion regulation difficulties (ERD) and psychopathology, further investigation of a possible mechanism is needed. The current study examined associations between BIS/BAS sensitivity, ERD, and SQ to depression, anxiety, and stress symptoms in an undergraduate sample (n=459). Positive relationships between BIS sensitivity and both ERD and stress symptoms, and negative relationships between BAS-reward sensitivity and both ERD and depression symptoms were observed. Furthermore, ERD were positively related to depression, anxiety, and stress symptoms. Succeeding analyses revealed differential relationships between ERD and depression, anxiety, and stress symptoms among good quality and poor quality sleepers. The findings are discussed within the context of personality dimensions and self-regulatory mechanisms, along with implications for the treatment of depression, anxiety and sleep difficulties. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

Effect of Modulated Alternating and Direct Current Iontophoresis on Transdermal Delivery of Lidocaine Hydrochloride

PubMed Central

Banga, Ajay K.

2014-01-01

The objective of this study was to investigate the iontophoretic delivery of lidocaine hydrochloride through porcine skin and to compare the effects of modulated alternating and direct current iontophoresis. Continuous and modulated iontophoresis was applied for one hour and two hours (0-1 h and 4-5th h) using a 1% w/v solution of lidocaine hydrochloride. Tape stripping was done to quantify the amount of drug permeated into stratum corneum and skin extraction studies were performed to determine the amount of drug in stripped skin. Receptor was sampled and analyzed over predefined time periods. The amount of lidocaine delivered across porcine skin after modulated direct current iontophoresis for 2 h was 1069.87 ± 120.03 μg/sq·cm compared to 744.81 ± 125.41 μg/sq·cm after modulated alternating current iontophoresis for 2 h. Modulated direct current iontophoresis also enhanced lidocaine delivery by twelvefold compared to passive delivery as 91.27 ± 18.71 μg/sq·cm of lidocaine was delivered after passive delivery. Modulated iontophoresis enhanced the delivery of lidocaine hydrochloride across porcine skin compared to the passive delivery. Modulated alternating current iontophoresis for duration of 2 h at frequency of 1 kHz was found to be comparable to the continuous direct current iontophoresis for 1 h. PMID:24959580

Effect of modulated alternating and direct current iontophoresis on transdermal delivery of lidocaine hydrochloride.

PubMed

Bhatia, Gaurav; Banga, Ajay K

2014-01-01

The objective of this study was to investigate the iontophoretic delivery of lidocaine hydrochloride through porcine skin and to compare the effects of modulated alternating and direct current iontophoresis. Continuous and modulated iontophoresis was applied for one hour and two hours (0-1 h and 4-5th h) using a 1% w/v solution of lidocaine hydrochloride. Tape stripping was done to quantify the amount of drug permeated into stratum corneum and skin extraction studies were performed to determine the amount of drug in stripped skin. Receptor was sampled and analyzed over predefined time periods. The amount of lidocaine delivered across porcine skin after modulated direct current iontophoresis for 2 h was 1069.87 ± 120.03 μ g/sq · cm compared to 744.81 ± 125.41 μ g/sq · cm after modulated alternating current iontophoresis for 2 h. Modulated direct current iontophoresis also enhanced lidocaine delivery by twelvefold compared to passive delivery as 91.27 ± 18.71 μ g/sq · cm of lidocaine was delivered after passive delivery. Modulated iontophoresis enhanced the delivery of lidocaine hydrochloride across porcine skin compared to the passive delivery. Modulated alternating current iontophoresis for duration of 2 h at frequency of 1 kHz was found to be comparable to the continuous direct current iontophoresis for 1 h.

Test report on the model 44000 seismometer system

NASA Astrophysics Data System (ADS)

1988-08-01

Teledyne Geotech has completed long period subsurface vault tests on four individual 44000 modules; two horizontal and two vertical. Each type of module is tested in tandem by comparing the outputs of aligned sensors. The latest data is outstanding, particularly that of the horizontal. At a period of 20 seconds, both vertical and horizontal channels show incoherent noise power of approximately-180 dB relative to 1 (m/sec-sq)sq/Hz. At a period of 64 seconds, the horizontal data is some 20 dB quieter than any previous borehole data and furthermore shows no increase with period, even at periods as long as 250 seconds. This performance is remarkable for a non-borehole installation. The vertical data shows excellent performance, although some temperature effects seem to be present. A detailed explanation of the experimental history and current tests follows.

Study of Bulk and Elementary Screw Dislocation Assisted Reverse Breakdown in Low-Voltage (less than 250 V) 4H-SiC p(+)n Junction diodes. Part 1; DC Properties

NASA Technical Reports Server (NTRS)

Neudeck, Philip G.; Huang, Wei; Dudley, Michael

1998-01-01

Given the high density (approx. 10(exp 4)/sq cm) of elementary screw dislocations (Burgers vector = 1c with no hollow core) in commercial SiC wafers and epilayers, all appreciable current (greater than 1 A) SiC power devices will likely contain elementary screw dislocations for the foreseeable future. It is therefore important to ascertain the electrical impact of these defects, particularly in high-field vertical power device topologies where SiC is expected to enable large performance improvements in solid-state high-power systems. This paper compares the DC-measured reverse-breakdown characteristics of low-voltage (less than 250 V) small-area (less than 5 x 10(exp -4)/sq cm) 4H-SiC p(+)n diodes with and without elementary screw dislocations. Compared to screw dislocation-free devices, diodes containing elementary screw dislocations exhibited higher pre-breakdown reverse leakage currents, softer reverse breakdown I-V knees, and highly localized microplasmic breakdown current filaments. The observed localized 4H-SiC breakdown parallels microplasmic breakdowns observed in silicon and other semiconductors, in which space-charge effects limit current conduction through the local microplasma as reverse bias is increased.

Study of Bulk and Elementary Screw Dislocation Assisted Reverse Breakdown in Low-Voltage (<250 V) 4H-SiC p+n Junction Diodes - Part 1: DC Properties

NASA Technical Reports Server (NTRS)

Neudeck, Philip G.; Huang, Wei; Dudley, Michael

1999-01-01

Given the high density (approx. 10(exp 4)/sq cm) of elementary screw dislocations (Burgers vector = lc with no hollow core) in commercial SiC wafers and epilayers, all appreciable current (greater than 1 A) SiC power devices will likely contain elementary screw dislocations for the foreseeable future. It is therefore important to ascertain the electrical impact of these defects, particularly in high-field vertical power device topologies where SiC is expected to enable large performance improvements in solid-state high-power systems. This paper compares the DC-measured reverse-breakdown characteristics of low-voltage (less than 250 V) small-area (less than 5 x 10(exp -4) sq cm) 4H-SiC p(+)n diodes with and without elementary screw dislocations. Compared to screw dislocation-free devices, diodes containing elementary screw dislocations exhibited higher pre-breakdown reverse leakage currents, softer reverse breakdown I-V knees, and highly localized microplasmic breakdown current filaments. The observed localized 4H-SiC breakdown parallels microplasmic breakdowns observed in silicon and other semiconductors, in which space-charge effects limit current conduction through the local microplasma as reverse bias is increased.

Characteristics of seasonal variation and solar activity dependence of the geomagnetic solar quiet daily variation

NASA Astrophysics Data System (ADS)

Shinbori, A.; Koyama, Y.; Nose, M.; Hori, T.

2017-12-01

Characteristics of seasonal variation and solar activity dependence of the X- and Y-components of the geomagnetic solar quiet (Sq) daily variation at Memanbetsu in mid-latitudes and Guam near the equator have been investigated using long-term geomagnetic field data with 1-h time resolution from 1957 to 2016. In this analysis, we defined the quiet day when the maximum value of the Kp index is less than 3 for that day. In this analysis, we used the monthly average of the adjusted daily F10.7 corresponding to geomagnetically quiet days. For identification of the monthly mean Sq variation in the X and Y components (Sq-X and Sq-Y), we first determined the baseline of the X and Y components from the average value from 22 to 2 h (LT: local time) for each quiet day. Next, we calculated a deviation from the baseline of the X- and Y-components of the geomagnetic field for each quiet day, and computed the monthly mean value of the deviation for each local time. As a result, Sq-X and Sq-Y shows a clear seasonal variation and solar activity dependence. The amplitude of seasonal variation increases significantly during high solar activities, and is proportional to the solar F10.7 index. The pattern of the seasonal variation is quite different between Sq-X and Sq-Y. The result of the correlation analysis between the solar F10.7 index and Sq-X and Sq-Y shows almost the linear relationship, but the slope and intercept of the linear fitted line varies as function of local time and month. This implies that the sensitivity of Sq-X and Sq-Y to the solar activity is different for different local times and seasons. The local time dependence of the offset value of Sq-Y at Guam and its seasonal variation suggest a magnetic field produced by inter-hemispheric field-aligned currents (FACs). From the sign of the offset value of Sq-Y, it is infer that the inter-hemispheric FACs flow from the summer to winter hemispheres in the dawn and dusk sectors and from the winter to summer hemispheres in the pre-noon to afternoon sectors. From the slope of the linear fitted line, we observe a weak solar activity dependence of the inter-hemispheric FACs, which shows that the intensity of inter-hemispheric FACs has positive and negative correlations in the morning-noon and afternoon sectors, respectively.

Development of practical high temperature superconducting wire for electric power application

NASA Technical Reports Server (NTRS)

Hawsey, Robert A.; Sokolowski, Robert S.; Haldar, Pradeep; Motowidlo, Leszek R.

1995-01-01

The technology of high temperature superconductivity has gone from beyond mere scientific curiousity into the manufacturing environment. Single lengths of multifilamentary wire are now produced that are over 200 meters long and that carry over 13 amperes at 77 K. Short-sample critical current densities approach 5 x 104 A/sq cm at 77 K. Conductor requirements such as high critical current density in a magnetic field, strain-tolerant sheathing materials, and other engineering properties are addressed. A new process for fabricating round BSCCO-2212 wire has produced wires with critical current densities as high as 165,000 A/sq cm at 4.2 K and 53,000 A/sq cm at 40 K. This process eliminates the costly, multiple pressing and rolling steps that are commonly used to develop texture in the wires. New multifilamentary wires with strengthened sheathing materials have shown improved yield strengths up to a factor of five better than those made with pure silver. Many electric power devices require the wire to be formed into coils for production of strong magnetic fields. Requirements for coils and magnets for electric power applications are described.

Determinants of social quality and their regional disparities: an integrated approach for health equity in South Korea.

PubMed

Jung, Minsoo

2014-01-01

Quality of life was originally included in the concept of social quality (SQ), which refers to the possibility of manifesting the life chance possessed by each individual and the consequences resulting from restricting such possibility. Social quality describes how favorable the socioenvironmental components are that impact the possibility of an individual's life. Despite the close relationship between community capacity and SQ, the components and regional disparities of SQ have not yet been examined. This study identified community-based distribution and disparities of SQ in South Korea, including health indicators. Standardized methods of SQ were used to examine the interrelationships among institutional capacity, citizen capacity, and their associations with population-based health indicators. Under the principles of conceptual suitability, reliability, clarity, comparability, and changeability, a total of 18 SQ indicators were collected, then transformed by European Social Survey standardization and Geographical Information System computation. In the results, the hidden structure that determined the distribution of the SQ indicators was the financial independence and average length of residence. Financial independence indicated the size of the budget that each local community controls was out of the total budget. The average length of residence showed a reverse-U-shape relation to the mutual supports of the residents. The regional distribution of the SQ indicators largely differed from the local economic index or health indicators. Disparities in SQ indicators are likely to arise from the degree of urbanization and the degree of citizens' cohesiveness. Therefore, it is necessary to analyze in-depth cases of both local government with high SQ indicators in all fields and those with low SQ indicators in all fields. In addition, there is a need to elucidate the structural causes and backgrounds that produce disparities in SQ, thus lowering disparities among regions, and to develop policies that will promote the overall and continuous improvement of SQ.

The Empathy and Systemizing Quotient: The Psychometric Properties of the Dutch Version and a Review of the Cross-Cultural Stability

ERIC Educational Resources Information Center

Groen, Y.; Fuermaier, A. B. M.; Den Heijer, A. E.; Tucha, O.; Althaus, M.

2015-01-01

The "Empathy Quotient" (EQ) and "Systemizing Quotient" (SQ) are used worldwide to measure people's empathizing and systemizing cognitive styles. This study investigates the psychometric properties of the Dutch EQ and SQ in healthy participants (n = 685), and high functioning males with autism spectrum disorder (n = 42). Factor…

A 5 x 40 cm rectangular-beam multipole ion source

NASA Technical Reports Server (NTRS)

Robinson, R. S.; Kaufman, H. R.; Haynes, C. M.

1981-01-01

A rectangular ion source particularly suited for the continuous sputter processing of materials over a wide area is discussed. A multipole magnetic field configuration was used to design an ion source with a 5 x 40 cm beam area, while a three-grid ion optics system was used to maximize ion current density at the design ion energy of 500 eV. An average extracted current density of about 4 mA/sq cm could be obtained from 500 eV Ar ions. The difference between the experimental performance and the design value of 6 mA/sq cm is attributed to grid misalignment due to thermal expansion. The discharge losses at typical operating conditions ranged from about 600 to 1000 eV/ion, in reasonable agreement with the design value of 800 eV/ion. The use of multiple rectangular-beam ion sources to process wider areas than would be possible with a single source was also studied, and the most uniform coverage was found to be obtainable with a 0 to 2 cm overlap.

Complexing DNA Origami Frameworks through Sequential Self-Assembly Based on Directed Docking.

PubMed

Suzuki, Yuki; Sugiyama, Hiroshi; Endo, Masayuki

2018-06-11

Ordered DNA origami arrays have the potential to compartmentalize space into distinct periodic domains that can incorporate a variety of nanoscale objects. Herein, we used the cavities of a preassembled 2D DNA origami framework to incorporate square-shaped DNA origami structures (SQ-origamis). The framework was self-assembled on a lipid bilayer membrane from cross-shaped DNA origami structures (CR-origamis) and subsequently exposed to the SQ-origamis. High-speed AFM revealed the dynamic adsorption/desorption behavior of the SQ-origamis, which resulted in continuous changing of their arrangements in the framework. These dynamic SQ-origamis were trapped in the cavities by increasing the Mg 2+ concentration or by introducing sticky-ended cohesions between extended staples, both from the SQ- and CR-origamis, which enabled the directed docking of the SQ-origamis. Our study offers a platform to create supramolecular structures or systems consisting of multiple DNA origami components. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Energy flux and characteristic energy of an elemental auroral structure

NASA Technical Reports Server (NTRS)

Lanchester, B. S.; Palmer, J. R.; Rees, M. H.; Lummerzheim, D.; Kaila, K.; Turunen, T.

1994-01-01

Electron density profiles acquired with the EISCAT radar at 0.2 s time resolution, together with TV images and photometric intensities, were used to study the characteristics of thin (less than 1 km) auroral arc structures that drifted through the field of view of the instruments. It is demonstrated that both high time and space resolution are essential for deriving the input parameters of the electron flux responsible for the elemental auroral structures. One such structure required a 400 mW/sq m (erg/sq cm s) downward energy flux carried by an 8 keV monochromatic electron flux equivalent to a current density of 50 micro Angstrom/sq m.

Sub micron area Nb/AlO(x)/Nb tunnel junctions for submillimeter mixer applications

NASA Technical Reports Server (NTRS)

Leduc, Henry G.; Bumble, B.; Cypher, S. R.; Judas, A. J.; Stern, J. A.

1992-01-01

In this paper, we report on a fabrication process developed for submicron area tunnel junctions. We have fabricated Nb/AlO(x)/Nb tunnel junctions with areas down to 0.1 sq micron using these techniques. The devices have shown excellent performance in receiver systems up to 500 GHz and are currently in use in radio astronomy observatories at 115, 230, and 500 GHz.

Alternative Solvents and Technologies for Precision Cleaning of Aerospace Components

NASA Technical Reports Server (NTRS)

Grandelli, Heather; Maloney, Phillip; DeVor, Robert; Hintze, Paul

2014-01-01

Precision cleaning solvents for aerospace components and oxygen fuel systems, including currently used Vertrel-MCA, have a negative environmental legacy, high global warming potential, and have polluted cleaning sites. Thus, alternative solvents and technologies are being investigated with the aim of achieving precision contamination levels of less than 1 mg/sq ft. The technologies being evaluated are ultrasonic bath cleaning, plasma cleaning and supercritical carbon dioxide cleaning.

Refined two-index entropy and multiscale analysis for complex system

NASA Astrophysics Data System (ADS)

Bian, Songhan; Shang, Pengjian

2016-10-01

As a fundamental concept in describing complex system, entropy measure has been proposed to various forms, like Boltzmann-Gibbs (BG) entropy, one-index entropy, two-index entropy, sample entropy, permutation entropy etc. This paper proposes a new two-index entropy Sq,δ and we find the new two-index entropy is applicable to measure the complexity of wide range of systems in the terms of randomness and fluctuation range. For more complex system, the value of two-index entropy is smaller and the correlation between parameter δ and entropy Sq,δ is weaker. By combining the refined two-index entropy Sq,δ with scaling exponent h(δ), this paper analyzes the complexities of simulation series and classifies several financial markets in various regions of the world effectively.

Fuel property effects on USAF gas turbine engine combustors and afterburners

NASA Technical Reports Server (NTRS)

Reeves, C. M.

1984-01-01

Since the early 1970s, the cost and availability of aircraft fuel have changed drastically. These problems prompted a program to evaluate the effects of broadened specification fuels on current and future aircraft engine combustors employed by the USAF. Phase 1 of this program was to test a set of fuels having a broad range of chemical and physical properties in a select group of gas turbine engine combustors currently in use by the USAF. The fuels ranged from JP4 to Diesel Fuel number two (DF2) with hydrogen content ranging from 14.5 percent down to 12 percent by weight, density ranging from 752 kg/sq m to 837 kg/sq m, and viscosity ranging from 0.830 sq mm/s to 3.245 sq mm/s. In addition, there was a broad range of aromatic content and physical properties attained by using Gulf Mineral Seal Oil, Xylene Bottoms, and 2040 Solvent as blending agents in JP4, JP5, JP8, and DF2. The objective of Phase 2 was to develop simple correlations and models of fuel effects on combustor performance and durability. The major variables of concern were fuel chemical and physical properties, combustor design factors, and combustor operating conditions.

An illustrative overview of semi-quantitative MRI scoring of knee osteoarthritis: lessons learned from longitudinal observational studies.

PubMed

Roemer, F W; Hunter, D J; Crema, M D; Kwoh, C K; Ochoa-Albiztegui, E; Guermazi, A

2016-02-01

To introduce the most popular magnetic resonance imaging (MRI) osteoarthritis (OA) semi-quantitative (SQ) scoring systems to a broader audience with a focus on the most commonly applied scores, i.e., the MOAKS and WORMS system and illustrate similarities and differences. While the main structure and methodology of each scoring system are publicly available, the core of this overview will be an illustrative imaging atlas section including image examples from multiple OA studies applying MRI in regard to different features assessed, show specific examples of different grades and point out pitfalls and specifics of SQ assessment including artifacts, blinding to time point of acquisition and within-grade evaluation. Similarities and differences between different scoring systems are presented. Technical considerations are followed by a brief description of the most commonly utilized SQ scoring systems including their responsiveness and reliability. The second part is comprised of the atlas section presenting illustrative image examples. Evidence suggests that SQ assessment of OA by expert MRI readers is valid, reliable and responsive, which helps investigators to understand the natural history of this complex disease and to evaluate potential new drugs in OA clinical trials. Researchers have to be aware of the differences and specifics of the different systems to be able to engage in imaging assessment and interpretation of imaging-based data. SQ scoring has enabled us to explain associations of structural tissue damage with clinical manifestations of the disease and with morphological alterations thought to represent disease progression. Copyright © 2015 Osteoarthritis Research Society International. Published by Elsevier Ltd. All rights reserved.

An illustrative overview of semi-quantitative MRI scoring of knee osteoarthritis: Lessons learned from longitudinal observational studies

PubMed Central

Roemer, Frank W.; Hunter, David J.; Crema, Michel D.; Kwoh, C. Kent; Ochoa-Albiztegui, Elena; Guermazi, Ali

2015-01-01

Objective To introduce the most popular magnetic resonance imaging (MRI) osteoarthritis (OA) semi-quantitative (SQ) scoring systems to a broader audience with a focus on the most commonly applied scores, i.e. the MOAKS and WORMS system and illustrate similarities and differences. Design While the main structure and methodology of each scoring system are publicly available, the core of this overview will be an illustrative imaging atlas section including image examples from multiple osteoarthritis studies applying MRI in regard to different features assessed, show specific examples of different grades and point out pitfalls and specifics of SQ assessment including artifacts, blinding to time point of acquisition and within-grade evaluation. Results Similarities and differences between different scoring systems are presented. Technical considerations are followed by a brief description of the most commonly utilized SQ scoring systems including their responsiveness and reliability. The second part is comprised of the atlas section presenting illustrative image examples. Conclusions Evidence suggests that SQ assessment of OA by expert MRI readers is valid, reliable and responsive, which helps investigators to understand the natural history of this complex disease and to evaluate potential new drugs in OA clinical trials. Researchers have to be aware of the differences and specifics of the different systems to be able to engage in imaging assessment and interpretation of imaging-based data. SQ scoring has enabled us to explain associations of structural tissue damage with clinical manifestations of the disease and with morphological alterations thought to represent disease progression. PMID:26318656

The aluminum electrode in AlCl3-alkali-halide melts.

NASA Technical Reports Server (NTRS)

Holleck, G. L.; Giner, J.

1972-01-01

Passivation phenomena have been observed upon cathodic and anodic polarization of the Al electrode in AlCl3-KCl-NaCl melts between 100 and 160 C. They are caused by formation of a solid salt layer at the electrode surface resulting from concentration changes upon current flow. The anodic limiting currents increased with temperature and with decreasing AlCl3 content of the melt. Current voltage curves obtained on a rotating aluminum disk showed a linear relationship between the anodic limiting current and omega to the minus 1/2 power. Upon cathodic polarization, dendrite formation occurs at the Al electrode. The activation overvoltage in AlCl3-KCl-NaCl was determined by galvanostatic current step methods. An apparent exchange current density of 270 mA/sq cm at 130 C and a double layer capacity of 40 plus or minus 10 microfarad/sq cm were measured.

High-temperature, high-power-density thermionic energy conversion for space

NASA Technical Reports Server (NTRS)

Morris, J. F.

1977-01-01

Theoretic converter outputs and efficiencies indicate the need to consider thermionic energy conversion (TEC) with greater power densities and higher temperatures within reasonable limits for space missions. Converter-output power density, voltage, and efficiency as functions of current density were determined for 1400-to-2000 K emitters with 725-to-1000 K collectors. The results encourage utilization of TEC with hotter-than-1650 K emitters and greater-than-6W sq cm outputs to attain better efficiencies, greater voltages, and higher waste-heat-rejection temperatures for multihundred-kilowatt space-power applications. For example, 1800 K, 30 A sq cm TEC operation for NEP compared with the 1650 K, 5 A/sq cm case should allow much lower radiation weights, substantially fewer and/or smaller emitter heat pipes, significantly reduced reactor and shield-related weights, many fewer converters and associated current-collecting bus bars, less power conditioning, and lower transmission losses. Integration of these effects should yield considerably reduced NEP specific weights.

SQ109, a New Drug Lead for Chagas Disease

PubMed Central

Veiga-Santos, Phercyles; Li, Kai; Lameira, Lilianne; de Carvalho, Tecia Maria Ulisses; Huang, Guozhong; Galizzi, Melina; Shang, Na; Li, Qian; Gonzalez-Pacanowska, Dolores; Hernandez-Rodriguez, Vanessa; Benaim, Gustavo; Guo, Rey-Ting; Urbina, Julio A.; Docampo, Roberto; de Souza, Wanderley

2015-01-01

We tested the antituberculosis drug SQ109, which is currently in advanced clinical trials for the treatment of drug-susceptible and drug-resistant tuberculosis, for its in vitro activity against the trypanosomatid parasite Trypanosoma cruzi, the causative agent of Chagas disease. SQ109 was found to be a potent inhibitor of the trypomastigote form of the parasite, with a 50% inhibitory concentration (IC50) for cell killing of 50 ± 8 nM, but it had little effect (50% effective concentration [EC50], ∼80 μM) in a red blood cell hemolysis assay. It also inhibited extracellular epimastigotes (IC50, 4.6 ± 1 μM) and the clinically relevant intracellular amastigotes (IC50, ∼0.5 to 1 μM), with a selectivity index of ∼10 to 20. SQ109 caused major ultrastructural changes in all three life cycle forms, as observed by light microscopy, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). It rapidly collapsed the inner mitochondrial membrane potential (Δψm) in succinate-energized mitochondria, acting in the same manner as the uncoupler FCCP [carbonyl cyanide 4-(trifluoromethoxy)phenylhydrazone], and it caused the alkalinization of internal acidic compartments, effects that are likely to make major contributions to its mechanism of action. The compound also had activity against squalene synthase, binding to its active site; it inhibited sterol side-chain reduction and, in the amastigote assay, acted synergistically with the antifungal drug posaconazole, with a fractional inhibitory concentration index (FICI) of 0.48, but these effects are unlikely to account for the rapid effects seen on cell morphology and cell killing. SQ109 thus most likely acts, at least in part, by collapsing Δψ/ΔpH, one of the major mechanisms demonstrated previously for its action against Mycobacterium tuberculosis. Overall, the results suggest that SQ109, which is currently in advanced clinical trials for the treatment of drug-susceptible and drug-resistant tuberculosis, may also have potential as a drug lead against Chagas disease. PMID:25583723

Player Selection Bias in National Football League Draftees.

PubMed

Beyer, Kyle S; Fukuda, David H; Redd, Michael J; Stout, Jeffrey R; Hoffman, Jay R

2016-11-01

Beyer, KS, Fukuda, DH, Redd, MJ, Stout, JR, and Hoffman, JR. Player selection bias in National Football League draftees. J Strength Cond Res 30(11): 2965-2971, 2016-Relative age effects (RAEs) have been studied as a potential factor associated with player selection bias in numerous sports. However, little research has examined the role of RAEs among National Football League (NFL) draftees. The purpose of the current study was to determine the existence of RAEs in NFL draftees from the last 10 NFL drafts. Draftee birth dates were collected and divided into calendar and scholastic quarters (SQ1-SQ4). To determine the presence of RAEs in specific subsets, NFL draftees were grouped according to round drafted, position, level of conference play, and age at the time of the draft. Significant χ tests (p ≤ 0.05) comparing observed birth-date distributions vs. the expected birth-date distribution from the general population were followed up by calculating the standardized residual for each quarter (z > ±2.0 indicating significance). Overall, no RAEs were seen when birth-date distribution was assessed using calendar quarters (p = 0.47), but more draftees were born in SQ2 (December-February) than expected (p < 0.01; z = +2.2). Significantly more draftees were born in SQ2 than expected for middle-round draftees (p = 0.01; z = +2.4), skill positions (p = 0.03; z = +2.3), Power Five college draftees (p < 0.01; z = +2.6), and early draftees (p < 0.01; z = +3.1). However, reverse RAEs were seen among late draftees, with fewer draftees being born in SQ2 (z = -3.6) and more being born in SQ4 (June-August; z = +2.6) than expected. In contrast to previous research, the current study observed significant RAEs in NFL draftees from the last 10 years. This player selection bias should be considered when evaluating long-term athlete development models in American football.

Akeno 20 km (2) air shower array (Akeno Branch)

NASA Technical Reports Server (NTRS)

Teshima, M.; Ohoka, H.; Matsubara, Y.; Hara, T.; Hatano, Y.; Hayashida, N.; He, C. X.; Honda, M.; Ishikawa, F.; Kamata, K.

1985-01-01

As the first stage of the future huge array, the Akeno air shower array was expanded to about 20 sq. km. by adding 19 scintillation detectors of 2.25 sq m area outside the present 1 sq. km. Akeno array with a new data collection system. These detectors are spaced about 1km from each other and connected by two optical fiber cables. This array has been in partial operation from 8th, Sep. 1984 and full operation from 20th, Dec. 1984. 20 sq m muon stations are planned to be set with 2km separation and one of them is now under construction. The origin of the highest energy cosmic rays is studied.

Development of a current collection loss management system for SDI homopolar power supplies

NASA Astrophysics Data System (ADS)

Brown, D. W.

1991-04-01

High speed, high power density current collection systems have been identified as an enabling technology required to construct homopolar power supplies to meet SDI missions. This work is part of a three-year effort directed towards the analysis, experimental verification, and prototype construction of a current collection system designed to operate continuously at 2 kA/sq cm, at a rubbing speed of 200 m/s, and with acceptable losses in a space environment. To date, no system has achieved these conditions simultaneously. This is the final report covering the three year period of performance on DOE contract AC03-86SF-16518. Major areas covered include design, construction and operation of a cryogenically cooled brush test rig, design and construction of a high speed brush test rig, optimization study for homopolar machines, loss analysis of the current collection system, and an application study which defines the air-core homopolar construction necessary to achieve the goal of 80 kW/kg generator power density.

Progress in HTS Trapped Field Magnets: J(sub c), Area, and Applications

NASA Technical Reports Server (NTRS)

Weinstein, Roy; Ren, Yanru; Liu, Jian-Xiong; Sawh, Ravi; Parks, Drew; Foster, Charles; Obot, Victor; Arndt, G. Dickey; Crapo, Alan

1995-01-01

Progress in trapped field magnets is reported. Single YBCO grains with diameters of 2 cm are made in production quantities, while 3 cm, 4 1/2 cm and 6 cm diameters are being explored. For single grain tiles: J(sub c) - 10,000 A/sq cm for melt textured grains; J(sub c) - 40,000 A/sq cm for light ion irradiation; and J(sub c) - 85,000 A/J(sub c) for heavy ion irradiation. Using 2 cm diameter tiles bombarded by light ions, we have fabricated a mini-magnet which trapped 2.25 Tesla at 77K, and 5.3 Tesla at 65K. A previous generation of tiles, 1 cm x 1 cm, was used to trap 7.0 Tesla at 55K. Unirradiated 2.0 cm tiles were used to provide 8 magnets for an axial gap generator, in a collaborative experiment with Emerson Electric Co. This generator delivered 100 Watts to a resistive load, at 2265 rpm. In this experiment, activation of the TFMs was accomplished by a current pulse of 15 ms duration. Tiles have also been studied for application as a bumper-tether system for the soft docking of spacecraft. A method for optimizing tether forces, and mechanisms of energy dissipation are discussed. A bus bar was constructed by welding three crystals while melt-texturing, such that their a,b planes were parallel and interleaved. The bus bar, of area approx. 2 sq cm, carried a transport current of 1000 amps, the limit of the testing equipment available.

Technology development for phosphoric acid fuel cell powerplant, phase 2

NASA Technical Reports Server (NTRS)

Christner, L.

1981-01-01

The development of materials, cell components, and reformers for on site integrated energy systems is described. Progress includes: (1) heat-treatment of 25 sq cm, 350 sq cm and 1200 sq cm cell test hardware was accomplished. Performance of fuel cells is improved by using this material; (2) electrochemical and chemical corrosion rates of heat-treated and as-molded graphite/phenolic resin composites in phosphoric acid were determined; (3) three cell, 5 in. x 15 in. stacks operated for up to 10,000 hours and 12 in. x 17 in. five cell stacks were tested for 5,000 hours; (4) a three cell 5 in. x 15 in. stack with 0.12 mg Pt/sq cm anodes and 0.25 mg Pt/sq cm cathodes was operated for 4,500 hours; and (5) an ERC proprietary high bubble pressure matrix, MAT-1, was tested for up to 10,000 hours.

3D Double-Quantum/Double-Quantum Exchange Spectroscopy of Protons under 100 kHz Magic Angle Spinning.

PubMed

Zhang, Rongchun; Duong, Nghia Tuan; Nishiyama, Yusuke; Ramamoorthy, Ayyalusamy

2017-06-22

Solid-state 1 H NMR spectroscopy has attracted much attention in the recent years due to the remarkable spectral resolution improvement by ultrafast magic-angle-spinning (MAS) as well as due to the sensitivity enhancement rendered by proton detection. Although these developments have enabled the investigation of a variety of challenging chemical and biological solids, the proton spectral resolution is still poor for many rigid solid systems owing to the presence of conformational heterogeneity and the unsuppressed residual proton-proton dipolar couplings even with the use of the highest currently feasible sample spinning speed of ∼130 kHz. Although a further increase in the spinning speed of the sample could be beneficial to some extent, there is a need for alternate approaches to enhance the spectral resolution. Herein, by fully utilizing the benefits of double-quantum (DQ) coherences, we propose a single radio frequency channel proton-based 3D pulse sequence that correlates double-quantum (DQ), DQ, and single-quantum (SQ) chemical shifts of protons. In addition to the two-spin homonuclear proximity information, the proposed 3D DQ/DQ/SQ experiment also enables the extraction of three-spin and four-spin proximities, which could be beneficial for revealing the dipolar coupled proton network in the solid state. Besides, the 2D DQ/DQ spectrum sliced at different isotropic SQ chemical shift values of the 3D DQ/DQ/SQ spectrum will also facilitate the identification of DQ correlation peaks and improve the spectral resolution, as it only provides the local homonuclear correlation information associated with the specific protons selected by the SQ chemical shift frequency. The 3D pulse sequence and its efficiency are demonstrated experimentally on small molecular compounds in the solid state. We expect that this approach would create avenues for further developments by suitably combining the benefits of partial deuteration of samples, selective excitation/decoupling pulses, heteronuclear spins for spectral editing, and nonuniform sampling.

Effects of Water Sprinklers on the Performance of Low Level AFFF Aircraft Hangar Fire Suppression Systems

DTIC Science & Technology

2000-05-22

AFFF fire suppression system. The combined overhead water-only sprinkler and low level AFFF system is being considered as a new protection scheme for...performance of a low level system during AFFF discharge (4.0 Lpm/sq m (0.1 gpm/sq ft)). Based on the results of these tests, the design criteria for...Navy hangar protection may be revised to incorporate AFFF application from only the low level system, combined with overhead closed-head guide response water sprinklers.

Design, Development and Flight Testing of the U.S. Army 4200 sq ft Parafoil Recovery System

NASA Technical Reports Server (NTRS)

Bennett, Thomas W.; Fox, Roy, Jr.

2005-01-01

The purpose of this paper is to describe the design, development and flight-testing of the U.S. Army 4200 sq ft parafoil recovery system built under NASA Contract NAS 9-00076. The 4200 f? parafoil described herein was a potential candidate to fulfill the U.S. Army requirement for a 10,000 lb useable payload precision guided recovery system. Design heritage as well as specific features, like lower surface inlets, confluence fitting, upper surface energy modulator design, deployment bag design and 60 ft diameter Ringslot drogue will be discussed. Initial flight test results, ground testing of various components to verify design margin and configuration changes will also be discussed. The 4200 sq ft parafoil recovery system completed three flight tests during 2003 at payload weights of over 15,000 Ibs

Efficient photovoltaic heterojunctions of indium tin oxides on silicon

NASA Technical Reports Server (NTRS)

Dubow, J. B.; Sites, J. R.; Burk, D. E.

1976-01-01

Heterojunction diodes of indium tin oxide films sputtered on to p-silicon using ion-beam techniques display significant photovoltaic effects when exposed to sunlight. Galvanomagnetic and optical measurements confirm that the oxide films are highly degenerate transparent semiconductors. At a tin oxide concentration of 10%, an open-circuit voltage of 0.51 V was observed along with a short-circuit current of 32 mA/sq cm, a fill factor of 0.70, and a conversion efficiency of 12%. As the concentration was raised to 70%, the voltage remained steady, the current fell to 27 mA/sq cm, and the fill factor fell to 0.60

Optical Line Radiation from Uranium Plasmas. Ph.D. Thesis; [for a gaseous core reactor

NASA Technical Reports Server (NTRS)

Maceda, E. L.

1977-01-01

The radiative energy current due to line radiation is calculated in a U 235 plasma over a temperature range of 5000 K to 8000 K. Also a variation in the neutron flux of 2 x 10 to the 12th power neutrons/ (sq cm-sec) to 2 x 10 to the 16th power neutrons/(sq cm-sec) is considered. The plasma forms a cylinder with a diameter and height of one meter. To calculate the radiative-energy current, a rate equation formalism is developed to solve for the atomic state densities along with a model for the energy levels in neutral and singly ionized uranium. Because the electron states in uranium lie below 5eV, recombination is the principle excitation mechanism. At and above 6000 K, inversions were found, and at all temperatures the line radiation at line center was greater than the corresponding black-body radiation. There are negligible differences in the radiative-energy current at 6000 K for variations in the neutron flux. The average opacity, which varied from 100 to 100,000 gm/sq cm, over the frequency range of line radiation is calculated.

Developing, mechanizing and testing of a digital active flutter suppression system for a modified B-52 wind-tunnel model

NASA Technical Reports Server (NTRS)

Matthew, J. R.

1980-01-01

A digital flutter suppression system was developed and mechanized for a significantly modified version of the 1/30-scale B-52E aeroelastic wind tunnel model. A model configuration was identified that produced symmetric and antisymmetric flutter modes that occur at 2873N/sq m (60 psf) dynamic pressure with violent onset. The flutter suppression system, using one trailing edge control surface and the accelerometers on each wing, extended the flutter dynamic pressure of the model beyond the design limit of 4788N/sq m (100 psf). The hardware and software required to implement the flutter suppression system were designed and mechanized using digital computers in a fail-operate configuration. The model equipped with the system was tested in the Transonic Dynamics Tunnel at NASA Langley Research Center and results showed the flutter dynamic pressure of the model was extended beyond 4884N/sq m (102 psf).

Thermal performance of a photographic laboratory process: Solar Hot Water System

NASA Technical Reports Server (NTRS)

Walker, J. A.; Jensen, R. N.

1982-01-01

The thermal performance of a solar process hot water system is described. The system was designed to supply 22,000 liters (5,500 gallons) per day of 66 C (150 F) process water for photographic processing. The 328 sq m (3,528 sq. ft.) solar field has supplied 58% of the thermal energy for the system. Techniques used for analyzing various thermal values are given. Load and performance factors and the resulting solar contribution are discussed.

Squamous cell carcinoma of the breast as a clinical diagnostic challenge

PubMed Central

Jakubowska, Katarzyna; Kańczuga-Koda, Luiza; Kisielewski, Wojciech; Koda, Mariusz; Famulski, Waldemar

2018-01-01

Squamous cell carcinoma (SqCC) of the breast should be differentiated between the primary skin keratinizing squamous carcinoma and squamous metaplastic cancer. In the current study, the cases of two patients who were diagnosed with SqCC originated from skin and the breast were discussed. A fine-needle aspiration biopsy confirmed the presence of atypical squamous cells. In both cases, the microscopic examination of the surgical specimen revealed a malignant neoplasm differentiated into SqCC characterized by keratinizing cancer cells with abundant eosiphilic cytoplasm with large, hyperchromatic vesicular nuclei. Immunohistochemical studies showed negative for progesterone and estrogen receptors and human epidermal growth factor receptor 2. Moreover, negative expression of cytokeratin 7 and 20 was confirmed. The diagnosis of the both tumors was established based on the detailed analysis of clinical, macroscopical and microscopical information. SqCC localized in the breast is a great diagnostic challenge in pathomorphology and more attention should be paid for analysis of such lesions in daily practice. PMID:29556390

Rectangular beam (5 X 40 cm multipole ion source). M.S. Thesis - Nov. 1979; [applications to electron bombardment in materials processing

NASA Technical Reports Server (NTRS)

Haynes, C. M.

1980-01-01

A 5 x 40 cm rectangular-beam ion source was designed and fabricated. A multipole field configuration was used to facilitate design of the modular rectangular chamber, while a three-grid ion optics system was used for increased ion current densities. For the multipole chamber, a magnetic integral of 0.000056 Tesla-m was used to contain the primary electrons. This integral value was reduced from the initial design value, with the reduction found necessary for discharge stability. The final value of magnetic integral resulted in discharge losses at typical operating conditions which ranged from 600 to 1000 eV/ion, in good agreement with the design value of 800 eV/ion. The beam current density at the ion optics was limited to about 3.2 mA/sq cm at 500 eV and to about 3.5 mA/sq cm at 1000 ev. The effects of nonuniform ion current, dimension tolerance, and grid thermal warping were considered. The use of multiple rectangular-beam ion sources to process wider areas than would be possible with a single source (approx. 40 cm) was also studied. Beam profiles were surveyed at a variety of operating conditions and the results of various amounts of beam overlap calculated.

Aerothermodynamic Design of the Mars Science Laboratory Backshell and Parachute Cone

NASA Technical Reports Server (NTRS)

Edquist, Karl T.; Dyakonov, Artem A.; Wright, Michael J.; Tang, Chun Y.

2009-01-01

Aerothermodynamic design environments are presented for the Mars Science Laboratory entry capsule backshell and parachute cone. The design conditions are based on Navier-Stokes flowfield simulations on shallow (maximum total heat load) and steep (maximum heat flux) design entry trajectories from a 2009 launch. Transient interference effects from reaction control system thruster plumes were included in the design environments when necessary. The limiting backshell design heating conditions of 6.3 W/sq cm for heat flux and 377 J/sq cm for total heat load are not influenced by thruster firings. Similarly, the thrusters do not affect the parachute cover lid design environments (13 W/sq cm and 499 J/sq cm). If thruster jet firings occur near peak dynamic pressure, they will augment the design environments at the interface between the backshell and parachute cone (7 W/sq cm and 174 J/sq cm). Localized heat fluxes are higher near the thruster fairing during jet firings, but these areas did not require additional thermal protection material. Finally, heating bump factors were developed for antenna radomes on the parachute cone

Preliminary Results of Field Emission Cathode Tests

NASA Technical Reports Server (NTRS)

Sovey, James S.; Kovaleski, Scott D.

2001-01-01

Preliminary screening tests of field emission cathodes such as chemical vapor deposited (CVD) diamond, textured pyrolytic graphite, and textured copper were conducted at background pressures typical of electric thruster test facilities to assess cathode performance and stability. Very low power electric thrusters which provide tens to hundreds micronewtons of thrust may need field emission neutralizers that have a capability of tens to hundreds of microamperes. From current voltage characteristics, it was found that the CVD diamond and textured metals cathodes clearly satisfied the Fowler-Nordheim emission relation. The CVD diamond and a textured copper cathode had average current densities of 270 and 380 mA/sq cm, respectively, at the beginning-of-life. After a few hours of operation the cathode emission currents degraded by 40 to 75% at background pressures in the 10(exp -5) Pa to 10(exp -4) Pa range. The textured pyrolytic graphite had a modest current density at beginning-of-life of 84 mA/sq cm, but this cathode was the most stable of all. Extended testing of the most promising cathodes is warranted to determine if current degradation is a burn-in effect or whether it is a long-term degradation process. Preliminary experiments with ferroelectric emission cathodes, which are ceramics with spontaneous electric polarization, were conducted. Peak current densities of 30 to 120 mA/sq cm were obtained for pulse durations of about 500 ns in the 10(exp -4) Pa pressure range.

Monte Carlo simulations of electron lateral distributions in the core region of 10(13) - 10(16) eV air showers

NASA Technical Reports Server (NTRS)

Ash, A. G.

1985-01-01

This paper contains details of computer models of shower development which have been used to investigate the experimental data on shower cores observed in the Leeds 35 sq m and Sacramento Peak (New Mexico) 20 sq m arrays of current limited spark (discharge) chambers. The simulations include predictions for primaries ranging from protons to iron nuclei (with heavy nuclei treated using both superposition and fragmentation models).

DOE Office of Scientific and Technical Information (OSTI.GOV)

McGettigan, C.K.; Hunt, D.G.

Colombia, where petroleum development began in 1908, is still yielding giant and supergiant discoveries. Recent successes result from improvements in exploration technology, in infrastructure, and in terms of participation offered by the Colombian government. Colombia has 13 sedimentary basins covering an area of 700,000 sq km out of a total country area of 1,350,000 sq km, including the continental shelf. This article highlights four of the seven basins currently productive in Colombia, providing an overview of geology and recent exploration activity.

Develop and test fuel cell powered on site integrated total energy systems. Phase 3: Full-scale power plant development

NASA Technical Reports Server (NTRS)

Kaufman, A.; Olson, B.; Pudick, S.; Wang, C. L.; Werth, J.; Whelan, J. A.

1986-01-01

The third in a series of 4kW stacks, consisting of 24 cells of the 13 inch x 23 inch cell size, has been on test for about 1600 hours. This stack is similar to the first two stacks, which ran 7000 and 8400 hours, respectively. The present stack incorporates technology improvements relating to the electrolyte-matrix, the current-collector assembly, and a reduction in the number of cooling plates. Performance is currently averaging about 0.64 per cell at 161 mA sq cm.

STS-1 operational flight profile. Volume 3: Ascent, cycle 3

NASA Technical Reports Server (NTRS)

1980-01-01

The ascent opeational flight profile for the space transportation system 1 flight is designed (1) to limit the maximum undispersed dynamic pressure to 580 lb/sq ft, (2) to follow the design load indicator profiles where q alpha is a specified profile and q beta is desired to be as close to zero as passible, and (3) to maximize nominal and abort performance. Significant trajectory parameters achieved are presented. A maximum dynamic pressure of 575 lb/sq ft was achieved, a minimum q alpha of -2187 lb-deg/sq ft was achieved, and q beta was limited to approximately + or - 100 lb-deg/sq ft in the high q region of the trajectory. The trajectory performance allows a press to main engine cutoff capability with one space shuttle main engine out at 262 seconds ground elapsed time. The orbital maneuvering system burns achieve a final orbit of 150.9 x 149.9 x 149.8 n. mi. and the desired inclination of 40.3 degrees.

Soil Quality Indexing Strategies for Evaluating Sugarcane Expansion in Brazil

PubMed Central

Cherubin, Maurício R.; Karlen, Douglas L.; Cerri, Carlos E. P.; Franco, André L. C.; Tormena, Cássio A.; Davies, Christian A.; Cerri, Carlos C.

2016-01-01

Increasing demand for biofuel has intensified land-use change (LUC) for sugarcane (Saccharum officinarum) expansion in Brazil. Assessments of soil quality (SQ) response to this LUC are essential for quantifying and monitoring sustainability of sugarcane production over time. Since there is not a universal methodology for assessing SQ, we conducted a field-study at three sites within the largest sugarcane-producing region of Brazil to develop a SQ index (SQI). The most common LUC scenario (i.e., native vegetation to pasture to sugarcane) was evaluated using six SQI strategies with varying complexities. Thirty eight soil indicators were included in the total dataset. Two minimum datasets were selected: one using principal component analysis (7 indicators) and the other based on expert opinion (5 indicators). Non-linear scoring curves were used to interpret the indicator values. Weighted and non-weighted additive methods were used to combine individual indicator scores into an overall SQI. Long-term conversion from native vegetation to extensive pasture significantly decreased overall SQ. In contrast, conversion from pasture to sugarcane had no significant impact on overall SQ at the regional scale, but site-specific responses were found. In general, sugarcane production improved chemical attributes (i.e., higher macronutrient levels and lower soil acidity); however it has negative effects on physical and biological attributes (i.e., higher soil compaction and structural degradation as well as lower soil organic carbon (SOC), abundance and diversity of macrofauna and microbial activity). Overall, we found that simple, user-friendly strategies were as effective as more complex ones for identifying SQ changes. Therefore, as a protocol for SQ assessments in Brazilian sugarcane areas, we recommend using a small number of indicators (e.g., pH, P, K, Visual Evaluation of Soil Structure -VESS scores and SOC concentration) and proportional weighting to reflect chemical, physical and biological processes within the soil. Our SQ evaluations also suggest that current approaches for expanding Brazilian sugarcane production by converting degraded pasture land to cropland can be a sustainable strategy for meeting increasing biofuel demand. However, management practices that alleviate negative impacts on soil physical and biological indicators must be prioritized within sugarcane producing areas to prevent unintentional SQ degradation over time. PMID:26938642

Soil Quality Indexing Strategies for Evaluating Sugarcane Expansion in Brazil.

PubMed

Cherubin, Maurício R; Karlen, Douglas L; Cerri, Carlos E P; Franco, André L C; Tormena, Cássio A; Davies, Christian A; Cerri, Carlos C

2016-01-01

Increasing demand for biofuel has intensified land-use change (LUC) for sugarcane (Saccharum officinarum) expansion in Brazil. Assessments of soil quality (SQ) response to this LUC are essential for quantifying and monitoring sustainability of sugarcane production over time. Since there is not a universal methodology for assessing SQ, we conducted a field-study at three sites within the largest sugarcane-producing region of Brazil to develop a SQ index (SQI). The most common LUC scenario (i.e., native vegetation to pasture to sugarcane) was evaluated using six SQI strategies with varying complexities. Thirty eight soil indicators were included in the total dataset. Two minimum datasets were selected: one using principal component analysis (7 indicators) and the other based on expert opinion (5 indicators). Non-linear scoring curves were used to interpret the indicator values. Weighted and non-weighted additive methods were used to combine individual indicator scores into an overall SQI. Long-term conversion from native vegetation to extensive pasture significantly decreased overall SQ. In contrast, conversion from pasture to sugarcane had no significant impact on overall SQ at the regional scale, but site-specific responses were found. In general, sugarcane production improved chemical attributes (i.e., higher macronutrient levels and lower soil acidity); however it has negative effects on physical and biological attributes (i.e., higher soil compaction and structural degradation as well as lower soil organic carbon (SOC), abundance and diversity of macrofauna and microbial activity). Overall, we found that simple, user-friendly strategies were as effective as more complex ones for identifying SQ changes. Therefore, as a protocol for SQ assessments in Brazilian sugarcane areas, we recommend using a small number of indicators (e.g., pH, P, K, Visual Evaluation of Soil Structure -VESS scores and SOC concentration) and proportional weighting to reflect chemical, physical and biological processes within the soil. Our SQ evaluations also suggest that current approaches for expanding Brazilian sugarcane production by converting degraded pasture land to cropland can be a sustainable strategy for meeting increasing biofuel demand. However, management practices that alleviate negative impacts on soil physical and biological indicators must be prioritized within sugarcane producing areas to prevent unintentional SQ degradation over time.

Local soil quality assessment of north-central Namibia: integrating farmers' and technical knowledge

NASA Astrophysics Data System (ADS)

Prudat, Brice; Bloemertz, Lena; Kuhn, Nikolaus J.

2018-02-01

Soil degradation is a major threat for farmers of semi-arid north-central Namibia. Soil conservation practices can be promoted by the development of soil quality (SQ) evaluation toolboxes that provide ways to evaluate soil degradation. However, such toolboxes must be adapted to local conditions to reach farmers. Based on qualitative (interviews and soil descriptions) and quantitative (laboratory analyses) data, we developed a set of SQ indicators relevant for our study area that integrates farmers' field experiences (FFEs) and technical knowledge. We suggest using participatory mapping to delineate soil units (Oshikwanyama soil units, KwSUs) based on FFEs, which highlight mostly soil properties that integrate long-term productivity and soil hydrological characteristics (i.e. internal SQ). The actual SQ evaluation of a location depends on the KwSU described and is thereafter assessed by field soil texture (i.e. chemical fertility potential) and by soil colour shade (i.e. SOC status). This three-level information aims to reveal SQ improvement potential by comparing, for any location, (a) estimated clay content against median clay content (specific to KwSU) and (b) soil organic status against calculated optimal values (depends on clay content). The combination of farmers' and technical assessment cumulates advantages of both systems of knowledge, namely the integrated long-term knowledge of the farmers and a short- and medium-term SQ status assessment. The toolbox is a suggestion for evaluating SQ and aims to help farmers, rural development planners and researchers from all fields of studies understanding SQ issues in north-central Namibia. This suggested SQ toolbox is adapted to a restricted area of north-central Namibia, but similar tools could be developed in most areas where small-scale agriculture prevails.

Application of high-quality SiO2 grown by multipolar ECR source to Si/SiGe MISFET

NASA Technical Reports Server (NTRS)

Sung, K. T.; Li, W. Q.; Li, S. H.; Pang, S. W.; Bhattacharya, P. K.

1993-01-01

A 5 nm-thick SiO2 gate was grown on an Si(p+)/Si(0.8)Ge(0.2) modulation-doped heterostructure at 26 C with an oxygen plasma generated by a multipolar electron cyclotron resonance source. The ultrathin oxide has breakdown field above 12 MV/cm and fixed charge density about 3 x 10 exp 10/sq cm. Leakage current as low as 1/micro-A was obtained with the gate biased at 4 V. The MISFET with 0.25 x 25 sq m gate shows maximum drain current of 41.6 mA/mm and peak transconductance of 21 mS/mm.

Current evaluation of the tripropellant concept

NASA Technical Reports Server (NTRS)

Zurawski, R. L.

1986-01-01

An analytical study was conducted to determine the specific-impulse advantages of adding metals to conventional liquid-bipropellant systems. These tripropellant systems theoretically offer higher specific impulse and increased propellant density compared with bipropellant systems. Metals considered were Be, Li, and Al. Bipropellant systems were H2/O2, N2H4/N2O4, RP-1/O2, and H2/F2. Thermochemical calculations were performed for sea-level expansion from 6.895-MN/sq. m. (1000-psia) chamber pressure over a wide range of mixture ratios and propellant compositions. Three-dimensional plots characterize the specific impulse of each tripropellant system. Technology issues pertinent to metallized propellant systems are discussed.

P/N In(Al) GaAs multijunction laser power converters

NASA Technical Reports Server (NTRS)

Wojtczuk, Steven; Parados, Themis; Walker, Gilbert

1994-01-01

Eight In(AI)GaAs PN junctions grown epitaxially on the semi-insulating wafer were monolithically integrated in series to boost the approximately 0.4V photovoltage per typical In(Al)GaAs junction to over 3 volts for the 1 sq cm laser power converted (LPC) chip. Advantages of multijunction LCP designs include the need for less circuitry for power reconditioning and the potential for lower I(sup 2)R power loss. As an example, these LPC's have a responsivity of approximately 1 amp/watt. With a single junction LPC, 100 watts/sq cm incident power would lead to about 100 A/sq cm short-circuit current at approximately 0.4V open-cicuit voltage. One disadvantage is the large current would lead to a large I(sup 2)R loss which would lower the fill factor so that 40 watts/sq cm output would not be obtained. Another is that few circuits are designed to work at 0.4 volts, so DC-DC power conversion circuitry would be necessary to raise the voltage to a reasonable level. The multijunction LPC being developed in this program is a step toward solving these problems. In the above example, an eight-junction LPC would have eight times the voltage, approximately 3V, so that DC-DC power conversion may not be needed in many instances. In addition, the multijunction LPC would have 1/8 the current of a single-junction LPC, for only 1/64 the I(sup 2)R loss if the series resistance is the same. Working monolithic multijunction laser power converters (LPC's) were made in two different compositions of the In(x)Al(y)Ga(1-x-y)As semiconductor alloy, In(0.53)Ga(0.47)As (0.74 eV) and In(0.5)Al(0.1)Ga(0.4)As (0.87 eV). The final 0.8 sq cm LPC's had output voltages of about 3 volts and output currents up to about one-half amp. Maximum 1.3 micron power conversion efficiencies were approximately 22 percent. One key advantage of multijunction LPC's is that they have higher output voltages, so that less DC-DC power conversion circuitry is needed in applications.

Prevalence of NRAS, PTEN and AKT1 gene mutations in the central nervous system metastases of non-small cell lung cancer.

PubMed

Nicoś, Marcin; Krawczyk, Paweł; Jarosz, Bożena; Sawicki, Marek; Trojanowski, Tomasz; Milanowski, Janusz

2017-01-01

Somatic mutations in NRAS, PTEN and AKT1 genes are rarely (~1%) reported in primary NSCLC, but their role in carcinogenesis have been proven. Therefore, we assessed the frequency of them in 145 FFPE tissue samples from CNS metastases of NSCLC using the real-time PCR technique. We identified four (two NRAS and single AKT1 and PTEN) mutations in CNS metastases of NSCLC. All mutations were observed in current male smokers (4% out of the male group; 4/100 and 4.25% out of smokers; 4/94). Three mutations have been detected in patients with SqCC (10.3% out of SqCC patients; 3/29), and only one mutation in the NRAS gene-in a patient with adenocarcinoma (1.25% out of AC patients; 1/80). The examined genes were mutually exclusive in terms of molecular background in KRAS; EGFR; DDR2; PIK3CA; HER2 and MEK1 genes that were evaluated in our previous studies. The OS of the patients who harbored NRAS, AKT1 and PTEN mutations was 10.1, 12.1, 7.3 and 4 months, respectively (vs 13.5 months of the studied group). Our results suggest that the presence of NRAS, PTEN and AKT1 gene mutations may have an influence on the occurrence of CNS metastases in patients with SqCC.

Anomaly of the geomagnetic Sq variation in Japan: effect from 3-D subterranean structure or the ocean effect?

NASA Astrophysics Data System (ADS)

Kuvshinov, Alexei; Utada, Hisashi

2010-12-01

Many years ago Rikitake et al. described the anomalous behaviour of the vertical component Z of the geomagnetic solar quiet (Sq) daily variation field at observatories in central and northern Japan - namely about 2 hr shift of the local noontime peak towards morning hours. They suggested that this anomaly is associated with the anomalous distribution of electrical conductivity in the mantle beneath central Japan. Although a few works have been done to confirm or argue this explanation, no clear answer has been obtained so far. The goal of this work is to understand the nature of this anomaly using our 3-D forward solution. The conductivity model of the Earth includes oceans of laterally variable conductance and conducting mantle either spherically symmetric or 3-D underneath. Data from six Japanese observatories at four seasons for two different years of the solar cycle are analysed. As an inducing ionospheric (Sq) current system, we use those provided by the Comprehensive Model (CM4) of Sabaka et al. Our analysis clearly demonstrates that 3-D induction in the ocean is responsible for the anomalous behaviour of Z daily variations in this region. We also show that the effects from a suite of 3-D mantle models that include mantle wedge and subducting slab are minor compared with the ocean effect.

Consideration of probability of bacterial growth for Jovian planets and their satellites

NASA Technical Reports Server (NTRS)

Taylor, D. M.; Berkman, R. M.; Divine, N.

1975-01-01

Environmental parameters affecting growth of bacteria (e.g., moisture, temperature, pH, and chemical composition) were compared with current atmospheric models for Jupiter and Saturn, and with the available physical data for their satellites. Different zones of relative probability of growth were identified for Jupiter and Saturn, with the highest in pressure regions of 1-10 million N/sq m (10 to 100 atmospheres) and 3-30 million N/sq m (30 to 300 atmospheres), respectively. Of the more than two dozen satellites, only the largest (Io, Europa, Ganymede, Callisto, and Titan) were found to be interesting biologically. Titan's atmosphere may produce a substantial greenhouse effect providing increased surface temperatures. Models predicting a dense atmosphere are compatible with microbial growth for a range of pressures at Titan's surface. For Titan's surface the probability of growth would be enhanced if (1) the surface is entirely or partially liquid (water), (2) volcanism (in an ice-water-steam system) is present, or (3) access to internal heat sources is significant.

Current and potential productivity of wheat for a controlled environment life support system

NASA Technical Reports Server (NTRS)

Bugbee, B. G.; Salisbury, F. B.

1989-01-01

Several determinants of crop growth are analyzed to determine theoretical and potentially achievable productivity. These include: incident photosynthetic photon flux (PPF); percent absorption of the incident PPF by photo synthetic tissue; photosynthetic efficiency; respiratory carbon use efficiency; and harvest index. The effects of optimal environmental and cultural factors on each of these determinants are also investigated. Results indicate that an increase in the percentage of absorbed photons is responsible for most of the improvement in wheat yields in an optimal controlled environment. An integrated PPF of 150 mol/sq m per d has produced 60 g/sq m per d of grain. There is almost a linear increase in wheat yields with increasing PPF. At intermediate and equal integrated daily PPF levels, photoperiod had little effect on yield per day or energy efficiency. Decreasing temperature from 23 to 17 deg increased yield per day by 20 percent but increased the life cycle from 62 to 89 days.

SQ 10 R.

ERIC Educational Resources Information Center

Shaughnessy, Michael F.

While many students have found SQ3R (Survey, Question, Read, Recite, Review) and PQ 4 R (Preview, Question, Read, Reflect, Recite, Review) systems to be helpful, developmental/remedial students may need more assistance than the average freshman. Students who need more help to deal with the massive amounts of reading that needs to be done in…

A novel squarylium dye for monitoring oxidative processes in lipid membranes.

PubMed

Trusova, Valeriya M; Gorbenko, Galyna P; Deligeorgiev, Todor; Gadjev, Nikolai; Vasilev, Aleksey

2009-11-01

A novel squaraine probe SQ-1 has been found to be appropriate for monitoring the peroxidation processes in membrane systems. Formation of free radicals was triggered by methemoglobin (metHb) or cytochrome c (cyt c) binding to the model lipid membranes composed of zwitterionic lipid phosphatidylcholine (PC) and anionic lipid cardiolipin (CL). Protein association with the lipid vesicles was followed by drastic quenching of SQ-1 fluorescence. The observed spectral changes were suppressed in the presence of free radical scavengers, butylated hydroxytoluene (BHT) and thiourea (TM) suggesting that SQ-1 decolorization can be attributed to its reactions with lipid radicals.

Uncooled pulsed zinc oxide semiconductor laser

NASA Astrophysics Data System (ADS)

Bogdankevich, O. V.; Darznek, S. A.; Zverev, M. M.; Kostin, N. N.; Krasavina, E. M.

1985-02-01

An optimized ZnO laser which operates at ambient temperature without cooling is reported, along with extension of the design to form a multielement high-power laser. ZnO single crystal plane-parallel wafers 0.22 mm thick, covered with total and semi-transparent coatings, were exposed to a 200 keV electron beam with a 10 nsec pulse and a current density up to 1 kA/sq cm. No damage was observed in the crystals at saturation. A 7 percent maximum efficiency at a reflection coefficient (RC) of 0.4 was associated with a maximum output of 25 kW and a light power density of 3 MW/sq cm. Cementing a ZnO wafer to a sapphire substrate, applying the same type of coatings and working with a RC of 0.6 yielded a maximum power of 300 kW/sq cm.

Hybrids of Solar Sail, Solar Electric, and Solar Thermal Propulsion for Solar-System Exploration

NASA Technical Reports Server (NTRS)

Wilcox, Brian H.

2012-01-01

Solar sails have long been known to be an attractive method of propulsion in the inner solar system if the areal density of the overall spacecraft (S/C) could be reduced to approx.10 g/sq m. It has also long been recognized that the figure (precise shape) of useful solar sails needs to be reasonably good, so that the reflected light goes mostly in the desired direction. If one could make large reflective surfaces with reasonable figure at an areal density of approx.10 g/sq m, then several other attractive options emerge. One is to use such sails as solar concentrators for solar-electric propulsion. Current flight solar arrays have a specific output of approx. 100W/kg at 1 Astronomical Unit (AU) from the sun, and near-term advances promise to significantly increase this figure. A S/C with an areal density of 10 g/sq m could accelerate up to 29 km/s per year as a solar sail at 1 AU. Using the same sail as a concentrator at 30 AU, the same spacecraft could have up to approx. 45 W of electric power per kg of total S/C mass available for electric propulsion (EP). With an EP system that is 50% power-efficient, exhausting 10% of the initial S/C mass per year as propellant, the exhaust velocity is approx. 119 km/s and the acceleration is approx. 12 km/s per year. This hybrid thus opens attractive options for missions to the outer solar system, including sample-return missions. If solar-thermal propulsion were perfected, it would offer an attractive intermediate between solar sailing in the inner solar system and solar electric propulsion for the outer solar system. In the example above, both the solar sail and solar electric systems don't have a specific impulse that is near-optimal for the mission. Solar thermal propulsion, with an exhaust velocity of the order of 10 km/s, is better matched to many solar system exploration missions. This paper derives the basic relationships between these three propulsion options and gives examples of missions that might be enabled by such hybrids.

Environmental assessment for the Satellite Power System (SPS): Studies of honey bees exposed to 2.45 GHz continuous wave electromagnetic energy

NASA Technical Reports Server (NTRS)

Gary, N. E.; Westerdahl, B. B.

1980-01-01

Post treatment brood development was normal and teratological effects were not detected at exposures of 3 to 50 mw sq cm for 30 minutes. Post treatment survival, longevity, orientation, navigation, and memory of adult bees were also normal after exposures of 3 to 50 mw sq cm for 30 minutes. Post treatment longevity of confined bees in the laboratory was normal after exposures of 3 to 50 mw sq cm for 24 hours. Thermoregulation of brood nest, foraging activity, brood rearing, and social interaction were not affected by chronic exposure to 1 mw sq cm during 28 days. In dynamic behavioral bioassays the frequency of entry and duration of activity of unrestrained, foraging adult bees was identical in microwave exposed areas versus control areas.

Red-emitting Ga/As,P///In,Ga/P heterojunction lasers

NASA Technical Reports Server (NTRS)

Kressel, H.; Nuese, C. J.; Olsen, G. H.

1978-01-01

The paper describes in detail the properties of vapor-grown double-heterojunction lasers of Ga(As,P)/(In,Ga)P with room-temperature threshold current densities as low as 3400 A/sq cm at 7000 A and 6600 A/sq cm at 6800 A. These thresholds are three to eight times smaller than those of (Al,Ga)As lasers in this wavelength range due to the shorter-wavelength direct-indirect transition in Ga(As,P). The optical and electrical characteristics of the Ga(As,P)/(In,Ga)P lasers are found to be similar to those of (Al,Ga)As, with fundamental transverse-mode operation to 70 C, and spontaneous carrier lifetimes between 5 and 8 nsec typically observed at low current densities.

Precision cleaning verification of fluid components by air/water impingement and total carbon analysis

NASA Technical Reports Server (NTRS)

Barile, Ronald G.; Fogarty, Chris; Cantrell, Chris; Melton, Gregory S.

1994-01-01

NASA personnel at Kennedy Space Center's Material Science Laboratory have developed new environmentally sound precision cleaning and verification techniques for systems and components found at the center. This technology is required to replace existing methods traditionally employing CFC-113. The new patent-pending technique of precision cleaning verification is for large components of cryogenic fluid systems. These are stainless steel, sand cast valve bodies with internal surface areas ranging from 0.2 to 0.9 sq m. Extrapolation of this technique to components of even larger sizes (by orders of magnitude) is planned. Currently, the verification process is completely manual. In the new technique, a high velocity, low volume water stream impacts the part to be verified. This process is referred to as Breathing Air/Water Impingement and forms the basis for the Impingement Verification System (IVS). The system is unique in that a gas stream is used to accelerate the water droplets to high speeds. Water is injected into the gas stream in a small, continuous amount. The air/water mixture is then passed through a converging/diverging nozzle where the gas is accelerated to supersonic velocities. These droplets impart sufficient energy to the precision cleaned surface to place non-volatile residue (NVR) contaminants into suspension in the water. The sample water is collected and its NVR level is determined by total organic carbon (TOC) analysis at 880 C. The TOC, in ppm carbon, is used to establish the NVR level. A correlation between the present gravimetric CFC113 NVR and the IVS NVR is found from experimental sensitivity factors measured for various contaminants. The sensitivity has the units of ppm of carbon per mg/sq ft of contaminant. In this paper, the equipment is described and data are presented showing the development of the sensitivity factors from a test set including four NVRs impinged from witness plates of 0.05 to 0.75 sq m.

Proton chemical shift tensors determined by 3D ultrafast MAS double-quantum NMR spectroscopy

NASA Astrophysics Data System (ADS)

Zhang, Rongchun; Mroue, Kamal H.; Ramamoorthy, Ayyalusamy

2015-10-01

Proton NMR spectroscopy in the solid state has recently attracted much attention owing to the significant enhancement in spectral resolution afforded by the remarkable advances in ultrafast magic angle spinning (MAS) capabilities. In particular, proton chemical shift anisotropy (CSA) has become an important tool for obtaining specific insights into inter/intra-molecular hydrogen bonding. However, even at the highest currently feasible spinning frequencies (110-120 kHz), 1H MAS NMR spectra of rigid solids still suffer from poor resolution and severe peak overlap caused by the strong 1H-1H homonuclear dipolar couplings and narrow 1H chemical shift (CS) ranges, which render it difficult to determine the CSA of specific proton sites in the standard CSA/single-quantum (SQ) chemical shift correlation experiment. Herein, we propose a three-dimensional (3D) 1H double-quantum (DQ) chemical shift/CSA/SQ chemical shift correlation experiment to extract the CS tensors of proton sites whose signals are not well resolved along the single-quantum chemical shift dimension. As extracted from the 3D spectrum, the F1/F3 (DQ/SQ) projection provides valuable information about 1H-1H proximities, which might also reveal the hydrogen-bonding connectivities. In addition, the F2/F3 (CSA/SQ) correlation spectrum, which is similar to the regular 2D CSA/SQ correlation experiment, yields chemical shift anisotropic line shapes at different isotropic chemical shifts. More importantly, since the F2/F1 (CSA/DQ) spectrum correlates the CSA with the DQ signal induced by two neighboring proton sites, the CSA spectrum sliced at a specific DQ chemical shift position contains the CSA information of two neighboring spins indicated by the DQ chemical shift. If these two spins have different CS tensors, both tensors can be extracted by numerical fitting. We believe that this robust and elegant single-channel proton-based 3D experiment provides useful atomistic-level structural and dynamical information for a variety of solid systems that possess high proton density.

Proton chemical shift tensors determined by 3D ultrafast MAS double-quantum NMR spectroscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Rongchun; Mroue, Kamal H.; Ramamoorthy, Ayyalusamy, E-mail: ramamoor@umich.edu

2015-10-14

Proton NMR spectroscopy in the solid state has recently attracted much attention owing to the significant enhancement in spectral resolution afforded by the remarkable advances in ultrafast magic angle spinning (MAS) capabilities. In particular, proton chemical shift anisotropy (CSA) has become an important tool for obtaining specific insights into inter/intra-molecular hydrogen bonding. However, even at the highest currently feasible spinning frequencies (110–120 kHz), {sup 1}H MAS NMR spectra of rigid solids still suffer from poor resolution and severe peak overlap caused by the strong {sup 1}H–{sup 1}H homonuclear dipolar couplings and narrow {sup 1}H chemical shift (CS) ranges, which rendermore » it difficult to determine the CSA of specific proton sites in the standard CSA/single-quantum (SQ) chemical shift correlation experiment. Herein, we propose a three-dimensional (3D) {sup 1}H double-quantum (DQ) chemical shift/CSA/SQ chemical shift correlation experiment to extract the CS tensors of proton sites whose signals are not well resolved along the single-quantum chemical shift dimension. As extracted from the 3D spectrum, the F1/F3 (DQ/SQ) projection provides valuable information about {sup 1}H–{sup 1}H proximities, which might also reveal the hydrogen-bonding connectivities. In addition, the F2/F3 (CSA/SQ) correlation spectrum, which is similar to the regular 2D CSA/SQ correlation experiment, yields chemical shift anisotropic line shapes at different isotropic chemical shifts. More importantly, since the F2/F1 (CSA/DQ) spectrum correlates the CSA with the DQ signal induced by two neighboring proton sites, the CSA spectrum sliced at a specific DQ chemical shift position contains the CSA information of two neighboring spins indicated by the DQ chemical shift. If these two spins have different CS tensors, both tensors can be extracted by numerical fitting. We believe that this robust and elegant single-channel proton-based 3D experiment provides useful atomistic-level structural and dynamical information for a variety of solid systems that possess high proton density.« less

Adding a second surprise question triggers general practitioners to increase the thoroughness of palliative care planning: results of a pilot RCT with cage vignettes.

PubMed

Weijers, F; Veldhoven, C; Verhagen, C; Vissers, K; Engels, Y

2018-04-19

In our aging society, palliative care should be a standard component of health care. However, currently it is only provided to a small proportion of patients, mostly to those with cancer, and restricted to the terminal phase. Many general practitioners (GPs) say that one of their most significant challenges is to assess the right moment to start anticipatory palliative care. The "Surprise Question" (SQ1: "Would I be surprised if this patient were to die in the next 12 months"?), if answered with "no", is an easy tool to apply in identifying patients in need of palliative care. However, this tool has a low specificity. Therefore, the aim of our pilot study was to determine if adding a second, more specific "Surprise Question" (SQ2: "Would I be surprised if this patient is still alive after 12 months"?) in case SQ1 is answered in the negative, prompts GPs to plan for anticipatory palliative care. By randomization, 28 GPs in the south-eastern part of the Netherlands were allocated to three different groups. They all received a questionnaire with four vignettes, respectively representing patients with advanced organ failure (A), end stage cancer (B), frailty (C), and recently diagnosed cancer (D). GPs in the first group did not receive additional information, the second group received SQ1 after each vignette, and the third group received SQ1 and SQ2 after each vignette. We rated their answers based on essential components of palliative care (here called RADIANT score). GPs in group 3 gave higher RADIANT scores to those vignettes in which they would be surprised if the patients were still alive after 12 months. In all groups, vignette B had the highest mean RADIANT score, followed by vignettes A and C, and the lowest on vignette D. Seventy-one percent of GPs in groups 2 and 3 considered SQ1 a helpful tool, and 75% considered SQ2 helpful. This innovative pilot study indicates that the majority of GPs think SQ2 is a helpful additional tool. The combination of the two "Surprise Questions" encourages GPs to make more specific plans for anticipatory palliative care.

46 CFR 171.055 - Intact stability requirements for a monohull sailing vessel or a monohull auxiliary sailing vessel.

Code of Federal Regulations, 2010 CFR

2010-10-01

... partially protected waters— EC01MR91.010 where— X=1.0 long tons/sq. ft. (10.9 metric tons/sq. meter). Y=1.1 long tons/sq. ft. (12.0 metric tons/sq. meter). Z=1.25 long tons/sq. ft. (13.7 metric tons/sq. meter.... meter). Y=1.7 long tons/sq. ft. (18.6 metric tons/sq. meter). Z=1.9 long tons/sq. ft. (20.8 metric tons...

Development and Validation of a Taxonomy for Characterizing Measurements in Health Self-Quantification.

PubMed

Almalki, Manal; Gray, Kathleen; Martin-Sanchez, Fernando

2017-11-03

The use of wearable tools for health self-quantification (SQ) introduces new ways of thinking about one's body and about how to achieve desired health outcomes. Measurements from individuals, such as heart rate, respiratory volume, skin temperature, sleep, mood, blood pressure, food consumed, and quality of surrounding air can be acquired, quantified, and aggregated in a holistic way that has never been possible before. However, health SQ still lacks a formal common language or taxonomy for describing these kinds of measurements. Establishing such taxonomy is important because it would enable systematic investigations that are needed to advance in the use of wearable tools in health self-care. For a start, a taxonomy would help to improve the accuracy of database searching when doing systematic reviews and meta-analyses in this field. Overall, more systematic research would contribute to build evidence of sufficient quality to determine whether and how health SQ is a worthwhile health care paradigm. The aim of this study was to investigate a sample of SQ tools and services to build and test a taxonomy of measurements in health SQ, titled: the classification of data and activity in self-quantification systems (CDA-SQS). Eight health SQ tools and services were selected to be examined: Zeo Sleep Manager, Fitbit Ultra, Fitlinxx Actipressure, MoodPanda, iBGStar, Sensaris Senspod, 23andMe, and uBiome. An open coding analytical approach was used to find all the themes related to the research aim. This study distinguished three types of measurements in health SQ: body structures and functions, body actions and activities, and around the body. The CDA-SQS classification should be applicable to align health SQ measurement data from people with many different health objectives, health states, and health conditions. CDA-SQS is a critical contribution to a much more consistent way of studying health SQ. ©Manal Almalki, Kathleen Gray, Fernando Martin-Sanchez. Originally published in the Journal of Medical Internet Research (http://www.jmir.org), 03.11.2017.

Development and Validation of a Taxonomy for Characterizing Measurements in Health Self-Quantification

PubMed Central

2017-01-01

Background The use of wearable tools for health self-quantification (SQ) introduces new ways of thinking about one’s body and about how to achieve desired health outcomes. Measurements from individuals, such as heart rate, respiratory volume, skin temperature, sleep, mood, blood pressure, food consumed, and quality of surrounding air can be acquired, quantified, and aggregated in a holistic way that has never been possible before. However, health SQ still lacks a formal common language or taxonomy for describing these kinds of measurements. Establishing such taxonomy is important because it would enable systematic investigations that are needed to advance in the use of wearable tools in health self-care. For a start, a taxonomy would help to improve the accuracy of database searching when doing systematic reviews and meta-analyses in this field. Overall, more systematic research would contribute to build evidence of sufficient quality to determine whether and how health SQ is a worthwhile health care paradigm. Objective The aim of this study was to investigate a sample of SQ tools and services to build and test a taxonomy of measurements in health SQ, titled: the classification of data and activity in self-quantification systems (CDA-SQS). Methods Eight health SQ tools and services were selected to be examined: Zeo Sleep Manager, Fitbit Ultra, Fitlinxx Actipressure, MoodPanda, iBGStar, Sensaris Senspod, 23andMe, and uBiome. An open coding analytical approach was used to find all the themes related to the research aim. Results This study distinguished three types of measurements in health SQ: body structures and functions, body actions and activities, and around the body. Conclusions The CDA-SQS classification should be applicable to align health SQ measurement data from people with many different health objectives, health states, and health conditions. CDA-SQS is a critical contribution to a much more consistent way of studying health SQ. PMID:29101092

Clouds Aerosols Internal Affaires: Increasing Cloud Fraction and Enhancing the Convection

NASA Technical Reports Server (NTRS)

Koren, Ilan; Kaufman, Yoram; Remer, Lorraine; Rosenfeld, Danny; Rudich, Yinon

2004-01-01

Clouds developing in a polluted environment have more numerous, smaller cloud droplets that can increase the cloud lifetime and liquid water content. Such changes in the cloud droplet properties may suppress low precipitation allowing development of a stronger convection and higher freezing level. Delaying the washout of the cloud water (and aerosol), and the stronger convection will result in higher clouds with longer life time and larger anvils. We show these effects by using large statistics of the new, 1km resolution data from MODIS on the Terra satellite. We isolate the aerosol effects from meteorology by regression and showing that aerosol microphysical effects increases cloud fraction by average of 30 presents for all cloud types and increases convective cloud top pressure by average of 35mb. We analyze the aerosol cloud interaction separately for high pressure trade wind cloud systems and separately for deep convective cloud systems. The resultant aerosol radiative effect on climate for the high pressure cloud system is: -10 to -13 W/sq m at the top of the atmosphere (TOA) and -11 to -14 W/sq m at the surface. For deeper convective clouds the forcing is: -4 to -5 W/sq m at the TOA and -6 to -7 W/sq m at the surface.

The relationship between serum asymmetric dimethylarginine levels and subjective sleep quality in normotensive patients with type 2 diabetes mellitus.

PubMed

Aribas, Alpay; Kayrak, Mehmet; Tekinalp, Mehmet; Akilli, Hakan; Alibasic, Hayrudin; Yildirim, Serkan; Gunduz, Mehmet; Taner, Alpaslan; Unlu, Ali

2015-05-01

Poor sleep quality (SQ) is associated with increased cardiovascular mortality and morbidity. Additionally, asymmetric dimethylarginine (ADMA) is an independent predictor of cardiovascular mortality and morbidity. However, no sufficient data regarding the relationship between ADMA levels and SQ have been reported. The goal of the current study was to evaluate the association between SQ and ADMA levels in normotensive patients with type 2 diabetes mellitus. The study participants consisted of 78 normotensive type 2 diabetics. The SQ of all participants was assessed using the Pittsburgh Sleep Quality Index (PSQI). Patients with a global PSQI score > 5 were defined as "poor sleepers." Factors associated with poor SQ were analyzed using a multiple regression model. Serum ADMA levels were measured using high performance liquid chromatography. The median ADMA levels of the poor sleepers were increased compared with patients defined as good sleepers (5.5 [4.2 to 6.6] vs. 4.4 [2.9 to 5.4], p < 0.01, respectively). However, the L-arginine/ADMA ratio was decreased in poor sleepers (p < 0.01). Global PSQI scores were positively correlated with ADMA levels (p < 0.01) and negatively correlated with the L-arginine/ADMA ratio (p = 0.02). ADMA levels were correlated with sleep latency (p < 0.01) and sleep efficiency (p = 0.01). Logistic regression analysis showed that ADMA levels (odds ratio [OR], 1.68; 95% confidence interval [CI], 1.16 to 2.44; p = 0.01) and body mass index (OR, 1.15; 95% CI, 1.01 to 1.31; p = 0.04) were associated with poor SQ independently of glomerular filtration rate, sex, age, duration of diabetes, hemoglobin A1c, total cholesterol, and systolic blood pressure. Self-reported SQ was independently associated with ADMA levels in normotensive patients with diabetes mellitus.

Identification of sensitive indicators to assess the interrelationship between soil quality, management practices and human health

NASA Astrophysics Data System (ADS)

Zornoza, R.; Acosta, J. A.; Bastida, F.; Domínguez, S. G.; Toledo, D. M.; Faz, A.

2014-09-01

Soil quality (SQ) assessment has been a challenging issue since soils present high variability in properties and functions. This paper aims to increase understanding of SQ through review of SQ assessments in different scenarios providing evidence about the interrelationship between SQ, land use and human health. There is a general consensus that there is a need to develop methods to assess and monitor SQ for assuring sustainable land use with no prejudicial effects on human health. This review points out the importance of adopting indicators of different nature (physical, chemical and biological) to achieve a holistic image of SQ. Most authors use single indicators to assess SQ and its relationship with land uses, being the most used indicators soil organic carbon and pH. The use of nitrogen and nutrients content has resulted sensitive for agricultural and forest systems, together with physical properties such as texture, bulk density, available water and aggregate stability. These physical indicators have also been widely used to assess SQ after land use changes. The use of biological indicators is less generalized, being microbial biomass and enzyme activities the most selected indicators. Although most authors assess SQ using independent indicators, it is preferable to combine some of them into models to create a soil quality index (SQI), since it provides integrated information about soil processes and functioning. The majority of revised articles used the same methodology to establish a SQI, based on scoring and weighting of different soil indicators, selected by multivariate analyses. The use of multiple linear regressions has been successfully used under forest land use. Urban soil quality has been poorly assessed, with lack of adoption of SQIs. In addition, SQ assessments were human health indicators or exposure pathways are incorporated are practically inexistent. Thus, new efforts should be carried out to establish new methodologies not only to assess soil quality in terms of sustainability, productivity and ecosystems quality, but also human health. Additionally, new challenges arise with the use and integration into SQIs of stable isotopic, genomic, proteomic and spectroscopy data.

Identification of sensitive indicators to assess the interrelationship between soil quality, management practices and human health

NASA Astrophysics Data System (ADS)

Zornoza, R.; Acosta, J. A.; Bastida, F.; Domínguez, S. G.; Toledo, D. M.; Faz, A.

2015-02-01

Soil quality (SQ) assessment has long been a challenging issue, since soils present high variability in properties and functions. This paper aims to increase the understanding of SQ through the review of SQ assessments in different scenarios providing evidence about the interrelationship between SQ, land use and human health. There is a general consensus that there is a need to develop methods to assess and monitor SQ for assuring sustainable land use with no prejudicial effects on human health. This review points out the importance of adopting indicators of different nature (physical, chemical and biological) to achieve a holistic image of SQ. Most authors use single indicators to assess SQ and its relationship with land uses - soil organic carbon and pH being the most used indicators. The use of nitrogen and nutrient content has resulted sensitive for agricultural and forest systems, together with physical properties such as texture, bulk density, available water and aggregate stability. These physical indicators have also been widely used to assess SQ after land use changes. The use of biological indicators is less generalized, with microbial biomass and enzyme activities being the most selected indicators. Although most authors assess SQ using independent indicators, it is preferable to combine some of them into models to create a soil quality index (SQI), since it provides integrated information about soil processes and functioning. The majority of revised articles used the same methodology to establish an SQI, based on scoring and weighting of different soil indicators, selected by means of multivariate analyses. The use of multiple linear regressions has been successfully used for forest land use. Urban soil quality has been poorly assessed, with a lack of adoption of SQIs. In addition, SQ assessments where human health indicators or exposure pathways are incorporated are practically inexistent. Thus, further efforts should be carried out to establish new methodologies to assess soil quality not only in terms of sustainability, productivity and ecosystem quality but also human health. Additionally, new challenges arise with the use and integration of stable isotopic, genomic, proteomic and spectroscopic data into SQIs.

Radiation Resistance Studies of Amorphous Silicon Alloy Photovoltaic Materials

NASA Technical Reports Server (NTRS)

Woodyard, James R.

1994-01-01

The radiation resistance of commercial solar cells fabricated from hydrogenated amorphous silicon alloys was investigated. A number of different device structures were irradiated with 1.0 MeV protons. The cells were insensitive to proton fluences below 1E12 sq cm. The parameters of the irradiated cells were restored with annealing at 200 C. The annealing time was dependent on proton fluence. Annealing devices for one hour restores cell parameters for fluences below lE14 sq cm require longer annealing times. A parametric fitting model was used to characterize current mechanisms observed in dark I-V measurements. The current mechanisms were explored with irradiation fluence, and voltage and light soaking times. The thermal generation current density and quality factor increased with proton fluence. Device simulation shows the degradation in cell characteristics may be explained by the reduction of the electric field in the intrinsic layer.

Laser-induced electron source in a vacuum diode

NASA Astrophysics Data System (ADS)

Ghera, U.; Boxman, R. L.; Kleinman, H.; Ruschin, S.

1989-11-01

Experiments were conducted in which a high-power CO2 TEA laser interacted with metallic cathode in a high-vacuum (10 to the -8th Torr) diode. For power densities lower than 5 x 10 to the 7th W/sq cm, no current was detected. For power densities in the range of 5 x 10 to the 7th to 5 x 10 to the 8th W/sq cm, the Cu cathode emitted a maximum current of 40 mA. At a higher power density level, a circuit-limited current of 8 A was detected. The jump of a few orders of magnitude in the current is attributed to breakdown of the diode gap. The experimental results are similar to those of a triggered vacuum gap, and a thorough comparison is presented in this paper. The influence of the pressure in the vacuum chamber on the current magnitude shows the active role that adsorbed gas molecules have in the initial breakdown. When the cathode material was changed from metal to metal oxide, much lower laser power densities were required to reach the breakdown current region.

Thermal protection systems manned spacecraft flight experience

NASA Technical Reports Server (NTRS)

Curry, Donald M.

1992-01-01

Since the first U.S. manned entry, Mercury (May 5, 1961), seventy-five manned entries have been made resulting in significant progress in the understanding and development of Thermal Protection Systems (TPS) for manned rated spacecraft. The TPS materials and systems installed on these spacecraft are compared. The first three vehicles (Mercury, Gemini, Apollo) used ablative (single-use) systems while the Space Shuttle Orbiter TPS is a multimission system. A TPS figure of merit, unit weight lb/sq ft, illustrates the advances in TPS material performance from Mercury (10.2 lb/sq ft) to the Space Shuttle (1.7 lb/sq ft). Significant advances have been made in the design, fabrication, and certification of TPS on manned entry vehicles (Mercury through Shuttle Orbiter). Shuttle experience has identified some key design and operational issues. State-of-the-art ceramic insulation materials developed in the 1970's for the Space Shuttle Orbiter have been used in the initial designs of aerobrakes. This TPS material experience has identified the need to develop a technology base from which a new class of higher temperature materials will emerge for advanced space transportation vehicles.

Thermal conductance of two interface materials and their applications in space systems

NASA Technical Reports Server (NTRS)

Scialdone, J. J.; Clatterbuck, C. H.; Wall, J. L.

1992-01-01

Two polymeric materials, the Cho-Therm 1671 elastomer and the CV-2946 conductive RTV silicone, have been evaluated. Tests were conducted in vacuum and in air, for many clamping pressures, power densities, and as a function of time. Results obtained show that the CV-2946 thermal conductance after 24 hour in vacuum is 0.62 W/sq cm C(4W/sq in C) when clamped with an average pressure of about 350 psi. The maximum conductance of Cho-Therm 1671 is 4.3 W/sq in C at the clamping pressure about 200 psi. After 72 h in vacuum, the conductance reaches a steady 3.4 W/sq in C, independent of clamping pressure. It is concluded that the tightly bolted, torqued fixtures do not buckle or distort and provide an optimum thermal conductance. The fixtures simulating an actual spacecraft configuration suffered severe bowing and separating, which caused considerable degradation of conductance values.

A low noise 230 GHz heterodyne receiver employing .25 sq micron area Nb/AlO(x)/Nb tunnel junctions

NASA Technical Reports Server (NTRS)

Kooi, Jacob W.; Chan, M.; Phillips, T. G.; Bumble, B.; Leduc, H. G.

1992-01-01

Recent results for a full height rectangular waveguide mixer with an integrated IF matching network are reported. Two 0.25 sq micron Nb/AlO(x)/Nb superconducting insulating superconducting (SIS) tunnel junctions with a current density of about 8500 A/sq cm and omega RC of about 2.5 at 230 GHz have been tested. Detailed measurements of the receiver noise have been made from 200-290 GHz for both junctions at 4.2 K. The lowest receiver noise temperatures were recorded at 239 GHz, measuring 48 K DSB at 4.2 K and 40 K DSB at 2.1 K. The 230 GHz receiver incorporates a one octave wide integrated low pass filter and matching network which transforms the pumped IF junction impedance to 50 ohms over a wide range of impedances.

New fluorescent probes for detection and characterization of amyloid fibrils

NASA Astrophysics Data System (ADS)

Gorbenko, Galyna; Trusova, Valeriya; Kirilova, Elena; Kirilov, Georgiy; Kalnina, Inta; Vasilev, Aleksey; Kaloyanova, Stefka; Deligeorgiev, Todor

2010-08-01

The applicability of the novel fluorescent probes, aminoderivative of benzanthrone ABM, squaraine dye SQ-1 and polymethine dye V2 to identification and structural analysis of amyloid fibrils has been evaluated using the lysozyme model system in which fibrillar aggregates have been formed in concentrated ethanol solution. The association constant, binding stoichiometry and molar fluorescence of the bound dye have been determined. ABM was found to surpass classical amyloid marker ThT in the sensitivity to the presence of fibrillar aggregates. Resonance energy transfer measurements involving ABM-SQ-1 and SQ-1-V2 donor-acceptor pairs yielded the limits for fractal-like dimension of lysozyme fibrils.

High energy efficiency and high power density proton exchange membrane fuel cells: Electrode kinetics and mass transport

NASA Technical Reports Server (NTRS)

Srinivasan, Supramaniam; Velev, Omourtag A.; Parthasathy, Arvind; Manko, David J.; Appleby, A. John

1991-01-01

The development of proton exchange membrane (PEM) fuel cell power plants with high energy efficiencies and high power densities is gaining momentum because of the vital need of such high levels of performance for extraterrestrial (space, underwater) and terrestrial (power source for electric vehicles) applications. Since 1987, considerable progress has been made in achieving energy efficiencies of about 60 percent at a current density of 200 mA/sq cm and high power densities (greater than 1 W/sq cm) in PEM fuel cells with high (4 mg/sq cm) or low (0.4 mg/sq cm) platinum loadings in electrodes. The following areas are discussed: (1) methods to obtain these high levels of performance with low Pt loading electrodes - by proton conductor impregnation into electrodes, localization of Pt near front surface; (2) a novel microelectrode technique which yields electrode kinetic parameters for oxygen reduction and mass transport parameters; (3) demonstration of lack of water transport from anode to cathode; (4) modeling analysis of PEM fuel cell for comparison with experimental results and predicting further improvements in performance; and (5) recommendations of needed research and development for achieving the above goals.

Air Leadership in Joint/Combined Operations: LT. General George E. Stratemeyer of the Eastern Air Command, 1943-1945

DTIC Science & Technology

1999-06-01

84th Sq “ (after Jan. 30) Dohazari 169th Wing (RAF Argatala 27th Sq Beaufighter Argatala 177th Sq “ Fenni 252nd Sq “ (To be activated by Jan. 30) 243rd...Wing (RAF) Fenni 11th Sq Hurricane IIC (F/B) Lalmai 60th Sq “ (F/B) Argatala 123rd Sq “ Fenni 76 134th Sq “ Parashuram 168th Wing (RAF) (221 Gp

Inactivation and pharmacological properties of sqKv1A homotetramers in Xenopus oocytes cannot account for behavior of the squid "delayed rectifier" K(+) conductance.

PubMed Central

Jerng, Henry H; Gilly, William F

2002-01-01

Considerable published evidence suggests that alpha-subunits of the cloned channel sqKv1A compose the "delayed rectifier" in the squid giant axon system, but discrepancies regarding inactivation properties of cloned versus native channels exist. In this paper we define the mechanism of inactivation for sqKv1A channels in Xenopus oocytes to investigate these and other discrepancies. Inactivation of sqKv1A in Xenopus oocytes was found to be unaffected by genetic truncation of the N-terminus, but highly sensitive to certain amino acid substitutions around the external mouth of the pore. External TEA and K(+) ions slowed inactivation of sqKv1A channels in oocytes, and chloramine T (Chl-T) accelerated inactivation. These features are all consistent with a C-type inactivation mechanism as defined for Shaker B channels. Treatment of native channels in giant fiber lobe neurons with TEA or high K(+) does not slow inactivation, nor does Chl-T accelerate it. Pharmacological differences between the two channel types were also found for 4-aminopyridine (4AP). SqKv1A's affinity for 4AP was poor at rest and increased after activation, whereas 4AP block occurred much more readily at rest with native channels than when they were activated. These results suggest that important structural differences between sqKv1A homotetramers and native squid channels are likely to exist around the external and internal mouths of the pore. PMID:12023225

The LeRC rail accelerators: Test designs and diagnostic techniques

NASA Technical Reports Server (NTRS)

Zana, L. M.; Kerslake, W. R.; Sturman, J. C.; Wang, S. Y.; Terdan, F. F.

1983-01-01

The feasibility of using rail accelerators for various in-space and to-space propulsion applications was investigated. A 1 meter, 24 sq mm bore accelerator was designed with the goal of demonstrating projectile velocities of 15 km/sec using a peak current of 200 kA. A second rail accelerator, 1 meter long with a 156.25 sq mm bore, was designed with clear polycarbonate sidewalls to permit visual observation of the plasma arc. A study of available diagnostic techniques and their application to the rail accelerator is presented. Specific topics of discussion include the use of interferometry and spectroscopy to examine the plasma armature as well as the use of optical sensors to measure rail displacement during acceleration. Standard diagnostics such as current and voltage measurements are also discussed.

Effect of reduced dose schedules and intramuscular injection of anthrax vaccine adsorbed on immunological response and safety profile: a randomized trial.

PubMed

Wright, Jennifer G; Plikaytis, Brian D; Rose, Charles E; Parker, Scott D; Babcock, Janiine; Keitel, Wendy; El Sahly, Hana; Poland, Gregory A; Jacobson, Robert M; Keyserling, Harry L; Semenova, Vera A; Li, Han; Schiffer, Jarad; Dababneh, Hanan; Martin, Sandra K; Martin, Stacey W; Marano, Nina; Messonnier, Nancy E; Quinn, Conrad P

2014-02-12

We evaluated an alternative administration route, reduced schedule priming series, and increased intervals between booster doses for anthrax vaccine adsorbed (AVA). AVA's originally licensed schedule was 6 subcutaneous (SQ) priming injections administered at months (m) 0, 0.5, 1, 6, 12 and 18 with annual boosters; a simpler schedule is desired. Through a multicenter randomized, double blind, non-inferiority Phase IV human clinical trial, the originally licensed schedule was compared to four alternative and two placebo schedules. 8-SQ group participants received 6 SQ injections with m30 and m42 "annual" boosters; participants in the 8-IM group received intramuscular (IM) injections according to the same schedule. Reduced schedule groups (7-IM, 5-IM, 4-IM) received IM injections at m0, m1, m6; at least one of the m0.5, m12, m18, m30 vaccine doses were replaced with saline. All reduced schedule groups received a m42 booster. Post-injection blood draws were taken two to four weeks following injection. Non-inferiority of the alternative schedules was compared to the 8-SQ group at m2, m7, and m43. Reactogenicity outcomes were proportions of injection site and systemic adverse events (AEs). The 8-IM group's m2 response was non-inferior to the 8-SQ group for the three primary endpoints of anti-protective antigen IgG geometric mean concentration (GMC), geometric mean titer, and proportion of responders with a 4-fold rise in titer. At m7 anti-PA IgG GMCs for the three reduced dosage groups were non-inferior to the 8-SQ group GMCs. At m43, 8-IM, 5-IM, and 4-IM group GMCs were superior to the 8-SQ group. Solicited injection site AEs occurred at lower proportions in the IM group compared to SQ. Route of administration did not influence the occurrence of systemic AEs. A 3 dose IM priming schedule with doses administered at m0, m1, and m6 elicited long term immunological responses and robust immunological memory that was efficiently stimulated by a single booster vaccination at 42 months. A priming series of 3 intramuscular doses administered at m0, m1, and m6 with a triennial booster was non-inferior to more complex schedules for achieving antibody response. Published by Elsevier Ltd.

A duplex real-time RT-PCR system with an internal control offers sensitive and reliable broad spectrum detection of Squash mosaic virus variants

USDA-ARS?s Scientific Manuscript database

Squash mosaic virus (SqMV) is a seed-borne virus, belonging to the genus Commovirus in the subfamily Comoviridae of family Secoviridae. SqMV has a bipartite single-stranded ribonucleic acid (RNA) genome (RNA1 and RNA2) encapsidated separately with two capsid proteins. Two serotypes (genotypes) of ...

Theoretical Study of Electron Transfer Properties of Squaraine Dyes for Dye Sensitized Solar Cell

NASA Astrophysics Data System (ADS)

Juwita, Ratna; Tsai, Hui-Hsu Gavin

2018-01-01

The environmental issues and high cost of Ru create many scientists to explore cheaper and safer sensitizer as alternative for dye sensitized solar cells (DSCs). Dyes play an important role in solar energy conversion efficiency. The squaraine (SQ) dyes has good spectral match with the solar spectra, therefore, SQ dyes have great potential for the applications in DSCs. SQ01_CA is an unsymmetrical SQ dye, reported by Grätzel and colleagues in 2007, featuring a D-π-spacer-A framework and has a carboxylic acid anchoring group. The electron donating ability of indolium in SQ01_CA and SQ01_CAA dyes is relatively weak, better performance may be achieved by introducing an additional donor moiety into indolium [1]. In this study, we investigate six unsymmetrical SQ dyes adsorbed on a (TiO2)38 cluster [2] using density functional theory (DFT) and time-dependent DFT to study electron transfer properties of squaraine dyes on their photophysical. SQ01_CA, WH-SQ01_CA, and WH-SQ02_CA use a carboxylic acid group as its electron acceptor. Furthermore, SQ01_CAA, WH-SQ01_CAA, and WH-SQ02_CAA use a cyanoacrylic acid group as its electron acceptor. WH-SQ01_CA and WH-SQ01_CAA have an alkyl, while WH-SQ02_CA and WH-SQ02_CAA have alkoxyl substituted diarylamines to the indolium donor of sensitizer SQ01_CA. Our calculations show with additional diarylamines in donor tail of WH-SQ02_CAA, the SQ dyes have red-shifted absorption and have slightly larger probability of electron density transferred to TiO2 moiety. Furthermore, an additional -CN group as electron a withdrawing group in the acceptor exhibits red-shifted absorption and enhances the electron density transferred to TiO2 and anchoring moiety after photo-excitation. The tendency of calculated probabilities of electron density being delocalized into TiO2 and driving force for excited-state electron injection of these studied SQ dyes is compatible with their experimentally observed.

A 3D Poly(ethylene glycol)-based Tumor Angiogenesis Model to Study the Influence of Vascular Cells on Lung Tumor Cell Behavior

PubMed Central

Roudsari, Laila C.; Jeffs, Sydney E.; Witt, Amber S.; Gill, Bartley J.; West, Jennifer L.

2016-01-01

Tumor angiogenesis is critical to tumor growth and metastasis, yet much is unknown about the role vascular cells play in the tumor microenvironment. In vitro models that mimic in vivo tumor neovascularization facilitate exploration of this role. Here we investigated lung adenocarcinoma cancer cells (344SQ) and endothelial and pericyte vascular cells encapsulated in cell-adhesive, proteolytically-degradable poly(ethylene) glycol-based hydrogels. 344SQ in hydrogels formed spheroids and secreted proangiogenic growth factors that significantly increased with exposure to transforming growth factor beta 1 (TGF-β1), a potent tumor progression-promoting factor. Vascular cells in hydrogels formed tubule networks with localized activated TGF-β1. To study cancer cell-vascular cell interactions, we engineered a 2-layer hydrogel with 344SQ and vascular cell layers. Large, invasive 344SQ clusters (area > 5,000 μm2, circularity < 0.25) developed at the interface between the layers, and were not evident further from the interface or in control hydrogels without vascular cells. A modified model with spatially restricted 344SQ and vascular cell layers confirmed that observed cluster morphological changes required close proximity to vascular cells. Additionally, TGF-β1 inhibition blocked endothelial cell-driven 344SQ migration. Our findings suggest vascular cells contribute to tumor progression and establish this culture system as a platform for studying tumor vascularization. PMID:27596933

A 3D Poly(ethylene glycol)-based Tumor Angiogenesis Model to Study the Influence of Vascular Cells on Lung Tumor Cell Behavior

NASA Astrophysics Data System (ADS)

Roudsari, Laila C.; Jeffs, Sydney E.; Witt, Amber S.; Gill, Bartley J.; West, Jennifer L.

2016-09-01

Tumor angiogenesis is critical to tumor growth and metastasis, yet much is unknown about the role vascular cells play in the tumor microenvironment. In vitro models that mimic in vivo tumor neovascularization facilitate exploration of this role. Here we investigated lung adenocarcinoma cancer cells (344SQ) and endothelial and pericyte vascular cells encapsulated in cell-adhesive, proteolytically-degradable poly(ethylene) glycol-based hydrogels. 344SQ in hydrogels formed spheroids and secreted proangiogenic growth factors that significantly increased with exposure to transforming growth factor beta 1 (TGF-β1), a potent tumor progression-promoting factor. Vascular cells in hydrogels formed tubule networks with localized activated TGF-β1. To study cancer cell-vascular cell interactions, we engineered a 2-layer hydrogel with 344SQ and vascular cell layers. Large, invasive 344SQ clusters (area > 5,000 μm2, circularity < 0.25) developed at the interface between the layers, and were not evident further from the interface or in control hydrogels without vascular cells. A modified model with spatially restricted 344SQ and vascular cell layers confirmed that observed cluster morphological changes required close proximity to vascular cells. Additionally, TGF-β1 inhibition blocked endothelial cell-driven 344SQ migration. Our findings suggest vascular cells contribute to tumor progression and establish this culture system as a platform for studying tumor vascularization.

Differences in quality-of-life dimensions of Adult Strabismus Quality of Life and Amblyopia & Strabismus Questionnaires.

PubMed

van de Graaf, Elizabeth S; Borsboom, Gerard J J M; van der Sterre, Geertje W; Felius, Joost; Simonsz, Huibert J; Kelderman, Henk

2017-09-01

The Adult Strabismus Quality of Life Questionnaire (AS-20) and the Amblyopia & Strabismus Questionnaire (A&SQ) both measure health-related quality of life in strabismus patients. We evaluated to what extent these instruments cover similar domains by identifying the underlying quality-of-life factors of the combined questionnaires. Participants were adults from a historic cohort with available orthoptic childhood data documenting strabismus and/or amblyopia. They had previously completed the A&SQ and were now asked to complete the AS-20. Factor analysis was performed on the correlation-matrix of the combined AS-20 and A&SQ data to identify common underlying factors. The identified factors were correlated with the clinical variables of angle of strabismus, degree of binocular vision, and visual acuity of the worse eye. One hundred ten patients completed both questionnaires (mean age, 44 years; range, 38-51 years). Six factors were found that together explained 78% of the total variance. The factor structure was dominated by the first four factors. One factor contained psychosocial and social-contact items, and another factor depth-perception items from both questionnaires. A third factor contained seven items-only from the AS-20-on eye strain, stress, and difficulties with reading and with concentrating. A fourth factor contained seven items-only from the A&SQ-on fear of losing the better eye and visual disorientation, specific for amblyopia. Current visual acuity of the worse eye correlated with depth-perception items and vision-related items, whereas current binocular vision correlated with psychosocial and social-contact items, in 93 patients. Factor analysis suggests that the AS-20 and A&SQ measure a similar psychosocial quality-of-life domain. However, functional problems like avoidance of reading, difficulty in concentrating, eye stress, reading problems, inability to enjoy hobbies, and need for frequent breaks when reading are represented only in the AS-20. During the development of the A&SQ, asthenopia items were considered insufficiently specific for strabismus and were excluded a priori. The patients who generated the items for the AS-20 had, in majority, adulthood-onset strabismus and diplopia and were, hence, more likely to develop such complaints than our adult patients with childhood-onset strabismus and/or amblyopia.

Design of a Day/Night Star Camera System

NASA Technical Reports Server (NTRS)

Alexander, Cheryl; Swift, Wesley; Ghosh, Kajal; Ramsey, Brian

1999-01-01

This paper describes the design of a camera system capable of acquiring stars during both the day and night cycles of a high altitude balloon flight (35-42 km). The camera system will be filtered to operate in the R band (590-810 nm). Simulations have been run using MODTRAN atmospheric code to determine the worse case sky brightness at 35 km. With a daytime sky brightness of 2(exp -05) W/sq cm/str/um in the R band, the sensitivity of the camera system will allow acquisition of at least 1-2 stars/sq degree at star magnitude limits of 8.25-9.00. The system will have an F2.8, 64.3 mm diameter lens and a 1340X1037 CCD array digitized to 12 bits. The CCD array is comprised of 6.8 X 6.8 micron pixels with a well depth of 45,000 electrons and a quantum efficiency of 0.525 at 700 nm. The camera's field of view will be 6.33 sq degree and provide attitude knowledge to 8 arcsec or better. A test flight of the system is scheduled for fall 1999.

HOLLOTRON switch for megawatt lightweight space inverters

NASA Technical Reports Server (NTRS)

Poeschel, R. L.; Goebel, D. M.; Schumacher, R. W.

1991-01-01

The feasibility of satisfying the switching requirements for a megawatt ultralight inverter system using HOLLOTRON switch technology was determined. The existing experimental switch hardware was modified to investigate a coaxial HOLLOTRON switch configuration and the results were compared with those obtained for a modified linear HOLLOTRON configuration. It was concluded that scaling the HOLLOTRON switch to the current and voltage specifications required for a megawatt converter system is indeed feasible using a modified linear configuration. The experimental HOLLOTRON switch operated at parameters comparable to the scaled coaxial HOLLOTRON. However, the linear HOLLOTRON data verified the capability for meeting all the design objectives simultaneously including current density (greater than 2 A/sq cm), voltage (5 kV), switching frequency (20 kHz), switching time (300 ns), and forward voltage drop (less than or equal to 20 V). Scaling relations were determined and a preliminary design was completed for an engineering model linear HOLLOTRON switch to meet the megawatt converter system specifications.

An Archival and Field Survey of Selected Historic Cultural Resources, Allatona Lake, Georgia.

DTIC Science & Technology

1984-06-25

United States from the subtropical waters of the Gulf of Mexico . The intense heating of the area triggers convectional air currents, resultinq in frequent...warm, moist air off the Gulf of Mexico with cooler, dryer air moving down from the North American interior. On the average it is less intense than the...of work oxer e i C . t, No. of mil-:h "o’m. 13 1 No. of other 2att’ I mile 10 No. of hogs per sq. mile 28.1 3. 15.2 1 1 . 93 1 No. of chickens er sq

Ion sputter textured graphite electrode plates

NASA Technical Reports Server (NTRS)

Curren, A. N.; Forman, R.; Sovey, J. S.; Wintucky, E. G. (Inventor)

1983-01-01

A specially textured surface of pyrolytic graphite exhibits extremely low yields of secondary electrons and reduced numbers of reflected primary electrons after impingement of high energy primary electrons. Electrode plates of this material are used in multistage depressed collectors. An ion flux having an energy between 500 iV and 1000 iV and a current density between 1.0 mA/sq cm and 6.0 mA/sq cm produces surface roughening or texturing which is in the form of needles or spires. Such textured surfaces are especially useful as anode collector plates in high tube devices.

Infrared photodetectors with tailorable response due to resonant plasmon absorption in epitaxial silicide particles embedded in silicon

NASA Technical Reports Server (NTRS)

Fathauer, R. W.; Dejewski, S. M.; George, T.; Jones, E. W.; Krabach, T. N.; Ksendzov, A.

1993-01-01

Tailorable infrared photoresponse in the 1-2 micron range are demonstrated in a device incorporating electrically floating metal silicide particles. Photons absorbed by excitation of the metallic-particle surface plasmon are shown to contribute to the photoresponse. Quantum efficiencies of roughly 0.2 percent are measured at 77 K, with dark currents of less than 2 nA/sq cm at a reverse bias of 1 V and detectivities of 4 x 10 exp 9 - 8 x 10 exp 9 cm sq rt Hz/W are obtained.

Carbon Nanotube Interconnect

NASA Technical Reports Server (NTRS)

Li, Jun (Inventor); Meyyappan, Meyya (Inventor)

2006-01-01

Method and system for fabricating an electrical interconnect capable of supporting very high current densities ( 10(exp 6)-10(exp 10) Amps/sq cm), using an array of one or more carbon nanotubes (CNTs). The CNT array is grown in a selected spaced apart pattern, preferably with multi-wall CNTs, and a selected insulating material, such as SiOw, or SiuNv is deposited using CVD to encapsulate each CNT in the array. An exposed surface of the insulating material is planarized to provide one or more exposed electrical contacts for one or more CNTs.

Transformer room fire tests

NASA Astrophysics Data System (ADS)

Fustich, C. D.

1980-03-01

A series of transformer room fire tests are reported to demonstate the shock hazard present when automatic sprinklers operate over energized electrical equipment. Fire protection was provided by standard 0.5 inch pendent automatic sprinklers temperature rated at 135 F and installed to give approximately 150 sq ft per head coverage. A 480 v dry transformer was used in the room to provide a three phase, four wire distribution system. It is shown that the induced currents in the test room during the various tests are relatively small and pose no appreciable personnel shock hazard.

Dst and a map of average equivalent ring current: 1958-2007

NASA Astrophysics Data System (ADS)

Love, J. J.

2008-12-01

A new Dst index construction is made using the original hourly magnetic-observatory data collected over the years 1958-2007; stations: Hermanus South Africa, Kakioka Japan, Honolulu Hawaii, and San Juan Puerto Rico. The construction method we use is generally consistent with the algorithm defined by Sugiura (1964), and which forms the basis for the standard Kyoto Dst index. This involves corrections for observatory baseline shifts, subtraction of the main-field secular variation, and subtraction of specific harmonics that approximate the solar-quiet (Sq) variation. Fourier analysis of the observatory data reveals the nature of Sq: it consists primarily of periodic variation driven by the Earth's rotation, the Moon's orbit, the Earth's orbit, and, to some extent, the solar cycle. Cross coupling of the harmonics associated with each of the external periodic driving forces results in a seemingly complicated Sq time series that is sometimes considered to be relatively random and unpredictable, but which is, in fact, well described in terms of Fourier series. Working in the frequency domain, Sq can be filtered out, and, upon return to the time domain, the local disturbance time series (Dist) for each observatory can be recovered. After averaging the local disturbance time series from each observatory, the global magnetic disturbance time series Dst is obtained. Analysis of this new Dst index is compared with that produced by Kyoto, and various biases and differences are discussed. The combination of the Dist and Dst time series can be used to explore the local-time/universal-time symmetry of an equivalent ring current. Individual magnetic storms can have a complicated disturbance field that is asymmetrical in longitude, presumably due to partial ring currents. Using 50 years of data we map the average local-time magnetic disturbance, finding that it is very nearly proportional to Dst. To our surprise, the primary asymmetry in mean magnetic disturbance is not between midnight and noon, but rather between dawn and dusk, with greatest mean disturbance occurring at dusk. As a result, proposed corrections to Dst for magnetopause and tail currents might be reasonably reconsidered.

An integrated development facility for the calibration of low-energy charged particle flight instrumentation

NASA Technical Reports Server (NTRS)

Biddle, A. P.; Reynolds, J. M.

1985-01-01

A system was developed for the calibration and development of thermal ion instrumentation. The system provides an extended beam with usable current rates, approx. 1 pA/sq cm, at beam energies as low as 1 eV, with much higher values available with increasing energy. A tandem electrostatic and variable geometry magnetic mirror configuration within the ion source optimizes the use of the ionizing electrons. The system is integrated under microcomputer control to allow automatic control and monitoring of the beam energy and composition and the mass and angle-dependent response of the instrument under test. The system is pumped by a combination of carbon vane and cryogenic sorption roughing pumps and ion and liquid helium operating pumps.

DE 1 observations of type 1 counterstreaming electrons and field-aligned currents

NASA Technical Reports Server (NTRS)

Lin, C. S.; Burch, J. L.; Barfield, J. N.; Sugiura, M.; Nielsen, E.

1984-01-01

Dynamics Explorer 1 satellite observations of plasma and magnetic fields during type one counterstreaming electron events are presented. Counterstreaming electrons are observed at high altitudes in the region of field-aligned current. The total current density computed from the plasma data in the 18-10,000 eV energy range is generally about 1-2 micro-A/sq m. For the downward current, low-energy electrons contribute more than 40 percent of the total plasma current density integrated above 18 eV. For the upward current, such electrons contribute less than 50 percent of that current density. Electron beams in the field-aligned direction are occasionally detected. The pitch angle distributions of counterstreaming electrons are generally enhanced at both small and large pitch angles. STARE simultaneous observations for one DE 1 pass indicated that the field-aligned current was closed through Pedersen currents in the ionosphere. The directions of the ionospheric current systems are consistent with the DE 1 observations at high altitudes.

High Electron Mobility Transistor Structures on Sapphire Substrates Using CMOS Compatible Processing Techniques

NASA Technical Reports Server (NTRS)

Mueller, Carl; Alterovitz, Samuel; Croke, Edward; Ponchak, George

2004-01-01

System-on-a-chip (SOC) processes are under intense development for high-speed, high frequency transceiver circuitry. As frequencies, data rates, and circuit complexity increases, the need for substrates that enable high-speed analog operation, low-power digital circuitry, and excellent isolation between devices becomes increasingly critical. SiGe/Si modulation doped field effect transistors (MODFETs) with high carrier mobilities are currently under development to meet the active RF device needs. However, as the substrate normally used is Si, the low-to-modest substrate resistivity causes large losses in the passive elements required for a complete high frequency circuit. These losses are projected to become increasingly troublesome as device frequencies progress to the Ku-band (12 - 18 GHz) and beyond. Sapphire is an excellent substrate for high frequency SOC designs because it supports excellent both active and passive RF device performance, as well as low-power digital operations. We are developing high electron mobility SiGe/Si transistor structures on r-plane sapphire, using either in-situ grown n-MODFET structures or ion-implanted high electron mobility transistor (HEMT) structures. Advantages of the MODFET structures include high electron mobilities at all temperatures (relative to ion-implanted HEMT structures), with mobility continuously improving to cryogenic temperatures. We have measured electron mobilities over 1,200 and 13,000 sq cm/V-sec at room temperature and 0.25 K, respectively in MODFET structures. The electron carrier densities were 1.6 and 1.33 x 10(exp 12)/sq cm at room and liquid helium temperature, respectively, denoting excellent carrier confinement. Using this technique, we have observed electron mobilities as high as 900 sq cm/V-sec at room temperature at a carrier density of 1.3 x 10(exp 12)/sq cm. The temperature dependence of mobility for both the MODFET and HEMT structures provides insights into the mechanisms that allow for enhanced electron mobility as well as the processes that limit mobility, and will be presented.

A 928 sq m (10000 sq ft) solar array

NASA Technical Reports Server (NTRS)

Lindberg, D. E.

1972-01-01

As the power requirements for space vehicles increases, the area of solar arrays that convert solar energy to usable electrical power increases. The requirements for a 928 sq m (10,000 sq ft) array, its design, and a full-scale demonstration of one quadrant (232 sq m (2500 sq ft)) deployed in a one-g field are described.

Early phase evaluation of SQ109 alone and in combination with rifampicin in pulmonary TB patients.

PubMed

Heinrich, Norbert; Dawson, Rodney; du Bois, Jeannine; Narunsky, Kim; Horwith, Gary; Phipps, Andrew J; Nacy, Carol A; Aarnoutse, Rob E; Boeree, Martin J; Gillespie, Stephen H; Venter, Amour; Henne, Sonja; Rachow, Andrea; Phillips, Patrick P J; Hoelscher, Michael; Diacon, Andreas H

2015-05-01

SQ109, an asymmetrical diamine, is a novel anti-TB drug candidate. This first study in patients was done to determine safety, tolerability, pharmacokinetics and bacteriological effect of different doses of SQ109 alone and in combination with rifampicin when administered over 14 days. Smear-positive pulmonary TB patients were randomized into six groups of 15 to receive once-daily oral treatment with 75, 150 or 300 mg of SQ109, rifampicin (10 mg/kg body weight), rifampicin plus 150 mg of SQ109, or rifampicin plus 300 mg of SQ109 for 14 days. Patients were hospitalized for supervised treatment, regular clinical, biochemical and electrocardiographic safety assessments, pharmacokinetic profiling and daily overnight sputum collection. SQ109 was safe and generally well tolerated. Mild to moderate dose-dependent gastrointestinal complaints were the most frequent adverse events. No relevant QT prolongation was noted. Maximum SQ109 plasma concentrations were lower than MICs. Exposure to SQ109 (AUC0-24) increased by drug accumulation upon repeated administration in the SQ109 monotherapy groups. Co-administration of SQ109 150 mg with rifampicin resulted in decreasing SQ109 exposures from day 1 to day 14. A higher (300 mg) dose of SQ109 largely outweighed the evolving inductive effect of rifampicin. The daily fall in log cfu/mL of sputum (95% CI) was 0.093 (0.126-0.059) with rifampicin, 0.133 (0.166-0.100) with rifampicin plus 150 mg of SQ109 and 0.089 (0.121-0.057) with rifampicin plus 300 mg of SQ109. Treatments with SQ109 alone showed no significant activity. SQ109 alone or with rifampicin was safe over 14 days. Upon co-administration with rifampicin, 300 mg of SQ109 yielded a higher exposure than the 150 mg dose. SQ109 did not appear to be active alone or to enhance the activity of rifampicin during the 14 days of treatment. © The Author 2015. Published by Oxford University Press on behalf of the British Society for Antimicrobial Chemotherapy. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Technology advancement of the static feed water electrolysis process

NASA Technical Reports Server (NTRS)

Jensen, F. C.; Schubert, F. H.

1977-01-01

Some results are presented of a research and development program to continue the development of a method to generate oxygen for crew metabolic consumption during extended manned space flights. The concept being pursued is that of static feed water electrolysis. Specific major results of the work included: (1) completion of a 30-day electrode test using a Life Systems, Inc.-developed high performance catalyst. During startup the cell voltages were as low as 1.38 V at current densities of 108 mA/sq cm (100 ASF) and temperatures of 355 K (180 F). At the end of 30 days of testing the cell voltages were still only 1.42 V at 108 mA/sq cm, (2) determination that the Static Feed Water Electrolysis Module does not release an aerosol of the cell electrolyte into the product gas streams after a break-in period of 24 hours following a new electrolyte charge, and (3) completion of a detailed design analysis of an electrochemical Oxygen Generation Subsystem at a three-man level (4.19 kg/day (9.24 lb/day) of oxygen).

Lightweight fuel cell powerplant components program

NASA Technical Reports Server (NTRS)

Martin, R. E.

1980-01-01

A lightweight hydrogen-oxygen alkaline fuel cell incorporated into the design of a lightweight fuel cell powerplant (LFCP) was analytically and experimentally developed. The powerplant operates with passive water removal which contributes to a lower system weight and extended operating life. A preliminary LFCP specification and design table were developed along with a lightweight power section for the LFCP design, consisting of repeating two-cell modules was designed. Two, four-cell modules were designed incorporating 0.508 sq ft active area space shuttle technology fuel cells. Over 1,200 hours of single-cell and over 8,800 hours of two-cell module testing was completed. The 0.25 sq ft active area lightweight cell design was shown to be capable of operating on propellant purity reactants out to a current density of 600ASF. Endurance testing of the two-cell module configuration exceeded the 2,500-hour LFCP voltage requirements out to 3700-hours. A two-cell module capable of operating at increased reactant pressure completed 1000 hours of operation at a 30 psia reactant pressure. A lightweight power section consisting of fifteen, two-cell modules connected electrically in series was fabricated.

75 FR 38773 - Submission for OMB Review; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-06

... needed to maintain proper coverage of the business universe. Based on information collected on the SQ... business birth survey keeps the sample universe current. Affected Public: Business or other for-profit; Not...

Design, construction and long life endurance testing of cathode assemblies for use in microwave high-power transmitting tubes

NASA Technical Reports Server (NTRS)

Batra, R.; Marino, D.

1986-01-01

The cathode life test program sponsored by NASA Lewis Research Center at Watkins-Johnson Company has been in continuous operation since 1972. Its primary objective has been to evaluate the long life capability of barium dispenser cathodes to produce emission current densities of 2 A sq. cm. or more in an operational environment simulating that of a highpower microwave tube. The life test vehicles were equipped with convergent flow electron guns, drift space tubes with solenoid magnets for electron beam confinement and water-cooled depressed collectors. A variety of cathode types has been tested, including GE Tungstate, Litton Impregnated, Philips Type B and M, Semicon types S and M, and Spectra-Mat Type M. Recent emphasis has been on monitoring the performance of Philips Type M cathodes at 2 A sq. cm. and Sprectra-Mat and Semicon Type M cathodes at 4 A sq. cm. These cathodes have been operated at a constant current of 616 mA and a cathode anode voltage on the order of 10 kV. Cathode temperatures were maintained at 1010 C true as measured from black body holes in the backs of the cathodes. This report presents results of the cathode life test program from July l982 through April l986. The results include hours of operation and performance data in the form of normalized emission current density versus temperature curves (Miram plots).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bockris, J.O.; Devanathan, M.A.V.

The galvanostatic double charging method was applied to determine the coverage of Ni cathodes with adsorbed atomic H in 2 N NaOH solutions. Anodic current densities were varied from 0.05 to 1.8 amp/sq cm. The plateau indicating absence of readsorption was between 0.6 and 1.8 amp/sq cm, for a constant cathodic c.d. of 1/10,000 amp/sq cm. The variation of the adsorbed H over cathodic c.d.'s ranging from 10 to the -6th power to 1/10 at a constant anodic c.d. of 1 amp/sq cm were calculated and the coverage calculated. The mechanism of the H evolution reaction was elucidated. The ratemore » determining step is discharge from a water molecules followed by rapid Tafel recombination. The rate constants for these processes and the rate constant for the ionisation, calculated with the extrapolated value of coverage for the reversible H electrode, were determined. A modification of the Tafel equation which takes into account both coverage and ionisation is in harmony with the results. A new method for the determination of coverage suitable for corrodible metals is described which involves the measurement of the rate of permeation of H by electrochemical techniques which enhances the sensitivity of the method. (Author)« less

Selling solar energy as a cash crop

NASA Technical Reports Server (NTRS)

Brantley, L. W.

1978-01-01

The paper considers solar energy equipment which, besides supplying energy for farmstead needs, would convert excess energy to a transportable form to sell to a power company. It is suggested that a concentrating two-axis tracking spheroidal collector would cost as little as $5/sq ft if mass produced. The proposed system uses 7854 sq ft of collector area (set in about one acre of land), and the cost payback is estimated.

Entropic nonadditivity, H theorem, and nonlinear Klein-Kramers equations.

PubMed

Dos Santos, M A F; Lenzi, E K

2017-11-01

We use the H theorem to establish the entropy and the entropic additivity law for a system composed of subsystems, with the dynamics governed by the Klein-Kramers equations, by considering relations among the dynamics of these subsystems and their entropies. We start considering the subsystems governed by linear Klein-Kramers equations and verify that the Boltzmann-Gibbs entropy is appropriated to this dynamics, leading us to the standard entropic additivity, S_{BG}^{(1∪2)}=S_{BG}^{1}+S_{BG}^{2}, consistent with the fact that the distributions of the subsystem are independent. We then extend the dynamics of these subsystems to independent nonlinear Klein-Kramers equations. For this case, the results show that the H theorem is verified for a generalized entropy, which does not preserve the standard entropic additivity for independent distributions. In this scenario, consistent results are obtained when a suitable coupling among the nonlinear Klein-Kramers equations is considered, in which each subsystem modifies the other until an equilibrium state is reached. This dynamics, for the subsystems, results in the Tsallis entropy for the system and, consequently, verifies the relation S_{q}^{(1∪2)}=S_{q}^{1}+S_{q}^{2}+(1-q)S_{q}^{1}S_{q}^{2}/k, which is a nonadditive entropic relation.

Photochemical Modeling of CH3 Abundances in the Outer Solar System

NASA Technical Reports Server (NTRS)

Lee, Anthony Y. T.; Yung, Yuk L.; Moses, Julianne

2000-01-01

Recent measurements of methyl radicals (CH3) in the upper atmospheres of Saturn and Neptune by the Infrared Space Observatory (ISO) provide new constraints to photochemical models of hydrocarbon chemistry in the outer solar system. The derived column abundances of CH3 on Saturn above 10 mbar and Neptune above the 0.2 mbar pressure level are (2.5 - 6.0) x 10(exp 13) / sq cm and (0.7 - 2.8) x 10(exp 13) / sq cm, respectively. We use the updated Caltech/Jet Propulsion Laboratory photochemical model, which incorporates hydrocarbon photochemistry, vertical molecular and bulk atmospheric eddy diffusion, and realistic radiative transfer modeling, to study the CH3 abundances in the upper atmosphere of the giant planets and Titan. We identify the key reactions that control the concentrations of CH3 in the model, such as the three-body recombination reaction, CH3 + CH3 + M yields C2H6 + M. We evaluate and extrapolate the three-body rate constant of this reaction to the low-temperature limit (1.8 x 10(exp -16) T(sup -3.75) e(sup -300/T), T < 300 K) and compare methyl radical abundances in five atmospheres: Jupiter, Saturn, Uranus, Neptune, and Titan. The sensitivity of our models to the rate coefficients for the reactions H + CH3 + M yields CH4 + M, H + C2H3 yields C2H2 + H2, (sup 1)CH2 + H2 yields CH3 + H, and H + C2H5 yields 2CH3, the branching ratios of CH4 photolysis, vertical mixing in the five atmospheres, and Lyman alpha photon enhancement at the orbit of Neptune have all been tested. The results of our model CH3 abundances for both Saturn (5.1 x 10(exp 13) / sq cm) and Neptune (2.2 x 10(exp 13) / sq cm) show good agreement with ISO Short Wavelength Spectrometer measurements. Using the same chemical reaction set, our calculations also successfully generate vertical profiles of stable hydrocarbons consistent with Voyager and ground-based measurements in these outer solar system atmospheres. Predictions of CH3 column concentrations (for p <= 0.2 mbar) in the atmospheres of Jupiter (3.3 x 10(exp 13) /sq cm), Uranus (2.5 x 10(exp 12) / sq cm), and Titan (1.9 x 10(exp 15) / sq cm) may be checked by future observations.

77 FR 23813 - Federal Property Suitable as Facilities To Assist the Homeless

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-20

... bldg. 4704 and dispatch--bldg 4707, fair conditions; need repairs Bldg. 8404 Redstone Arsenal Redstone...; current use: varies; fair to poor conditions--bldgs. need repairs; possible asbestos 5 Bldgs. Hunter Army...: 1208, 1209, 1211, 1212, 1221 Comments: Off-site removal only; sq. ft. varies; current use: varies; fair...

77 FR 35993 - Federal Property Suitable as Facilities To Assist the Homeless

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-15

.../equipment, possible asbestos/PCBs District of Columbia West Heating Plant 1051 29th St. NW Washington DC... and hwy) and utilities easements, asbestos and lead base paint identified, most current use: unknown...-X-MI-664B Comments: 89 sq. ft; current use: storage; non-friable asbestos and lead base paint...

Development and validation of an automated system for detection and assessment of scratching in the rodent

PubMed Central

Marino, Marc; Huang, Polly; Malkmus, Shelle; Robertshaw, Erin; Mac, Elaine A.; Shatterman, Yuri; Yaksh, Tony L.

2012-01-01

Pruritus, the sensation of itch, which evokes reflex scratching behavior, has a diverse etiology. Because of its clinical significance, mechanisms of pruriception are an important topic. In the present work we describe and validate a paw motion detector (PMD) system. The system employs a small removable metal band placed on one hind paw that provides a signal indicative of paw movement through perturbation of an electromagnetic (EM) field. C57Bl/6 mice were fitted with a unilateral hind paw band and adapted to testing cylinders equipped with EM signal emission and detection. The following observations were made: 1) in mice, unilateral SQ injection of 48/80 into the dorsolateral aspect of the neck evoked periodic high frequency bursts of scratching at the injected site with the ipsilateral (banded) but not the contralateral (not banded) hind paw. 2) Cross correlation between PMD and human observer counts after SQ 48/80 using the specified computational algorithm revealed a highly significant correlation. 3) SQ histamine and 48/80 over a 1 hour interval produced dose dependent scratching, which diphenhydramine dose dependently reversed. Chloroquine scratching displayed an inverse u-shaped dose response curve, which was insensitive to diphenhydramine. 4) SQ 48/80 at intervals over 28 days showed no change in the scratching response within the same cohort of mice. 5) Power analysis showed 40% changes in scratching activity could be detected at the p<0.05 level with groups of 4 mice. These observations indicate that the system described can efficiently define the actions and pharmacology of pruritogenic agents. PMID:22971351

LDEF data correlation to existing NASA debris environment models

NASA Technical Reports Server (NTRS)

Atkinson, Dale R.; Allbrooks, Martha K.; Watts, Alan J.

1992-01-01

The Long Duration Exposure Facility (LDEF) was recovered in January 1990, following 5.75 years exposure of about 130 sq. m to low-Earth orbit. About 25 sq. m of this surface area was aluminum 6061 T-6 exposed in every direction. In addition, about 17 sq. m of Scheldahl G411500 silver-Teflon thermal control blankets were exposed in 9 of the 12 directions. Since the LDEF was gravity gradient stabilized and did not rotate, the directional dependence of the flux can be easily distinguished. During the disintegration of the LDEF, all impact features larger than 0.5 mm into aluminum were documented for diameters and locations. In addition, the diameters and locations of all impact features larger than 0.3 mm into Scheldahl G411500 thermal control blankets were also documented. This data, along with additional information collected from LDEF materials will be compared with current meteoroid and debris models. This comparison will provide a validation of the models and will identify discrepancies between the models and the data.

Methane emissions from Alaska Arctic tundra - An assessment of local spatial variability

NASA Technical Reports Server (NTRS)

Morrissey, L. A.; Livingston, G. P.

1992-01-01

The findings of an extensive midsummer survey of CH4 emissions measurements representing the Alaska Arctic tundra are presented. Variability in rates of emissions was similar in magnitude on local and regional scales, ranging from 0 to 286.5 mg/sq m/d overall and often varying across two orders of magnitude within 0.5 m distances. Primary control on rates of emission was determined by the substrate and position of the water table relative to the surface. Emission rates in the Arctic Foothills ranged from 0.2 mg/sq m/d for tussock tundra to 55.53 mg/sq m/d over wet meadows. Plant-mediated release of CH4 to the atmosphere was directly proportional to green leaf area and represented 92-98 percent of the total emission rates over vegetated sites. The results suggest the current published emission rates may have overestimated the contribution of boreal ecosystems to the global CH4 budget by several fold.

GaAs-oxide interface states - Gigantic photoionization via Auger-like process

NASA Technical Reports Server (NTRS)

Lagowski, J.; Kazior, T. E.; Gatos, H. C.; Walukiewicz, W.; Siejka, J.

1981-01-01

Spectral and transient responses of photostimulated current in MOS structures were employed for the study of GaAs-anodic oxide interface states. Discrete deep traps at 0.7 and 0.85 eV below the conduction band were found with concentrations of 5 x 10 to the 12th/sq cm and 7 x 10 to the 11th/sq cm, respectively. These traps coincide with interface states induced on clean GaAs surfaces by oxygen and/or metal adatoms (submonolayer coverage). In contrast to surfaces with low oxygen coverage, the GaAs-thick oxide interfaces exhibited a high density (about 10 to the 14th/sq cm) of shallow donors and acceptors. Photoexcitation of these donor-acceptor pairs led to a gigantic photoionization of deep interface states with rates 1000 times greater than direct transitions into the conduction band. The gigantic photoionization is explained on the basis of energy transfer from excited donor-acceptor pairs to deep states.

Out-of-core Evaluations of Uranium Nitride-fueled Converters

NASA Technical Reports Server (NTRS)

Shimada, K.

1972-01-01

Two uranium nitride fueled converters were tested parametrically for their initial characterization and are currently being life-tested out of core. Test method being employed for the parametric and the diagnostic measurements during the life tests, and test results are presented. One converter with a rhenium emitter had an initial output power density of 6.9 W/ sq cm at the black body emitter temperature of 1900 K. The power density remained unchanged for the first 1000 hr of life test but degraded nearly 50% percent during the following 1000 hr. Electrode work function measurements indicated that the uranium fuel was diffusing out of the emitter clad of 0.635 mm. The other converter with a tungsten emitter had an initial output power density of 2.2 W/ sq cm at 1900 K with a power density of 3.9 W/sq cm at 4300 h. The power density suddenly degraded within 20 hr to practically zero output at 4735 hr.

Long-term cryogenic space storage system

NASA Technical Reports Server (NTRS)

Hopkins, R. A.; Chronic, W. L.

1973-01-01

Discussion of the design, fabrication and testing of a 225-cu ft spherical cryogenic storage system for long-term subcritical applications under zero-g conditions in storing subcritical cryogens for space vehicle propulsion systems. The insulation system design, the analytical methods used, and the correlation between the performance test results and analytical predictions are described. The best available multilayer insulation materials and state-of-the-art thermal protection concepts were applied in the design, providing a boiloff rate of 0.152 lb/hr, or 0.032% per day, and an overall heat flux of 0.066 Btu/sq ft hr based on a 200 sq ft surface area. A six to eighteen month cryogenic storage is provided by this system for space applications.

SQDFT: Spectral Quadrature method for large-scale parallel O(N) Kohn-Sham calculations at high temperature

NASA Astrophysics Data System (ADS)

Suryanarayana, Phanish; Pratapa, Phanisri P.; Sharma, Abhiraj; Pask, John E.

2018-03-01

We present SQDFT: a large-scale parallel implementation of the Spectral Quadrature (SQ) method for O(N) Kohn-Sham Density Functional Theory (DFT) calculations at high temperature. Specifically, we develop an efficient and scalable finite-difference implementation of the infinite-cell Clenshaw-Curtis SQ approach, in which results for the infinite crystal are obtained by expressing quantities of interest as bilinear forms or sums of bilinear forms, that are then approximated by spatially localized Clenshaw-Curtis quadrature rules. We demonstrate the accuracy of SQDFT by showing systematic convergence of energies and atomic forces with respect to SQ parameters to reference diagonalization results, and convergence with discretization to established planewave results, for both metallic and insulating systems. We further demonstrate that SQDFT achieves excellent strong and weak parallel scaling on computer systems consisting of tens of thousands of processors, with near perfect O(N) scaling with system size and wall times as low as a few seconds per self-consistent field iteration. Finally, we verify the accuracy of SQDFT in large-scale quantum molecular dynamics simulations of aluminum at high temperature.

Dense crystalline packings of ellipsoids

NASA Astrophysics Data System (ADS)

Jin, Weiwei; Jiao, Yang; Liu, Lufeng; Yuan, Ye; Li, Shuixiang

2017-03-01

An ellipsoid, the simplest nonspherical shape, has been extensively used as a model for elongated building blocks for a wide spectrum of molecular, colloidal, and granular systems. Yet the densest packing of congruent hard ellipsoids, which is intimately related to the high-density phase of many condensed matter systems, is still an open problem. We discover an unusual family of dense crystalline packings of self-dual ellipsoids (ratios of the semiaxes α : √{α }:1 ), containing 24 particles with a quasi-square-triangular (SQ-TR) tiling arrangement in the fundamental cell. The associated packing density ϕ exceeds that of the densest known SM2 crystal [ A. Donev et al., Phys. Rev. Lett. 92, 255506 (2004), 10.1103/PhysRevLett.92.255506] for aspect ratios α in (1.365, 1.5625), attaining a maximal ϕ ≈0.758 06 ... at α = 93 /64 . We show that the SQ-TR phase derived from these dense packings is thermodynamically stable at high densities over the aforementioned α range and report a phase diagram for self-dual ellipsoids. The discovery of the SQ-TR crystal suggests organizing principles for nonspherical particles and self-assembly of colloidal systems.

High energy density aluminum-oxygen cell

NASA Technical Reports Server (NTRS)

Rudd, E. J.; Gibbons, D. W.

1993-01-01

An alternative to a secondary battery as the power source for vehicle propulsion is a fuel cell. An example of this is the metal-air fuel cell using metals such as aluminum, zinc, or iron. Aluminum is a particularly attractive candidate, having high energy and power densities, being environmentally acceptable, and having a large, established industrial base for production and distribution. An aluminum-oxygen system is currently under development for a UUV test vehicle, and recent work has focussed upon low corrosion aluminum alloys and an electrolyte management system for processing the by-products of the energy-producing reactions. This paper summarizes the progress made in both areas. Anode materials capable of providing high utilization factors over current densities ranging from S to 150 mA/sq cm have been identified. These materials are essential to realizing an acceptable mission life for the UUV. With respect to the electrolyte management system, a filter/precipitator unit has been successfully operated for over 250 hours in a large scale, half-cell system.

Nonsterol Isoprenoids Activate Human Constitutive Androstane Receptor in an Isoform-Selective Manner in Primary Cultured Mouse Hepatocytes.

PubMed

Rondini, Elizabeth A; Duniec-Dmuchowski, Zofia; Kocarek, Thomas A

2016-04-01

Our laboratory previously reported that accumulation of nonsterol isoprenoids following treatment with the squalene synthase inhibitor, squalestatin 1 (SQ1) markedly induced cytochrome P450 (CYP)2B1 mRNA and reporter activity in primary cultured rat hepatocytes, which was dependent on activation of the constitutive androstane receptor (CAR). The objective of the current study was to evaluate whether isoprenoids likewise activate murine CAR (mCAR) or one or more isoforms of human CAR (hCAR) produced by alternative splicing (SPTV, hCAR2; APYLT, hCAR3). We found that SQ1 significantly induced Cyp2b10 mRNA (∼3.5-fold) in primary hepatocytes isolated from both CAR-wild-type and humanized CAR transgenic mice, whereas the 3-hydroxy-3-methylglutaryl-CoA reductase inhibitor pravastatin had no effect. In the absence of CAR, basal Cyp2b10 mRNA levels were reduced by 28-fold and the effect of SQ1 on Cyp2b10 induction was attenuated. Cotransfection with an expression plasmid for hCAR1, but not hCAR2 or hCAR3, mediated SQ1-induced CYP2B1 and CYP2B6 reporter activation in hepatocytes isolated from CAR-knockout mice. This effect was also observed following treatment with the isoprenoid trans,trans-farnesol. The direct agonist CITCO increased interaction of hCAR1, hCAR2, and hCAR3 with steroid receptor coactivator-1. However, no significant effect on coactivator recruitment was observed with SQ1, suggesting an indirect activation mechanism. Further results from an in vitro ligand binding assay demonstrated that neither farnesol nor other isoprenoids are direct ligands for hCAR1. Collectively, our findings demonstrate that SQ1 activates CYP2B transcriptional responses through farnesol metabolism in an hCAR1-dependent manner. Further, this effect probably occurs through an indirect mechanism. Copyright © 2016 by The American Society for Pharmacology and Experimental Therapeutics.

Nonsterol Isoprenoids Activate Human Constitutive Androstane Receptor in an Isoform-Selective Manner in Primary Cultured Mouse Hepatocytes

PubMed Central

Rondini, Elizabeth A.; Duniec-Dmuchowski, Zofia

2016-01-01

Our laboratory previously reported that accumulation of nonsterol isoprenoids following treatment with the squalene synthase inhibitor, squalestatin 1 (SQ1) markedly induced cytochrome P450 (CYP)2B1 mRNA and reporter activity in primary cultured rat hepatocytes, which was dependent on activation of the constitutive androstane receptor (CAR). The objective of the current study was to evaluate whether isoprenoids likewise activate murine CAR (mCAR) or one or more isoforms of human CAR (hCAR) produced by alternative splicing (SPTV, hCAR2; APYLT, hCAR3). We found that SQ1 significantly induced Cyp2b10 mRNA (∼3.5-fold) in primary hepatocytes isolated from both CAR–wild-type and humanized CAR transgenic mice, whereas the 3-hydroxy-3-methylglutaryl-CoA reductase inhibitor pravastatin had no effect. In the absence of CAR, basal Cyp2b10 mRNA levels were reduced by 28-fold and the effect of SQ1 on Cyp2b10 induction was attenuated. Cotransfection with an expression plasmid for hCAR1, but not hCAR2 or hCAR3, mediated SQ1-induced CYP2B1 and CYP2B6 reporter activation in hepatocytes isolated from CAR-knockout mice. This effect was also observed following treatment with the isoprenoid trans,trans-farnesol. The direct agonist CITCO increased interaction of hCAR1, hCAR2, and hCAR3 with steroid receptor coactivator-1. However, no significant effect on coactivator recruitment was observed with SQ1, suggesting an indirect activation mechanism. Further results from an in vitro ligand binding assay demonstrated that neither farnesol nor other isoprenoids are direct ligands for hCAR1. Collectively, our findings demonstrate that SQ1 activates CYP2B transcriptional responses through farnesol metabolism in an hCAR1-dependent manner. Further, this effect probably occurs through an indirect mechanism. PMID:26798158

Muscarinic type 2 receptors in the lateral dorsal tegmental area modulate cocaine and food seeking behavior in rats.

PubMed

Shabani, S; Foster, R; Gubner, N; Phillips, T J; Mark, G P

2010-10-13

The cholinergic input from the lateral dorsal tegmental area (LDTg) modulates the dopamine cells of the ventral tegmental area (VTA) and plays an important role in cocaine taking. Specific pharmacological agents that block or stimulate muscarinic receptors in the LDTg change acetylcholine (ACh) levels in the VTA. Furthermore, manipulations of cholinergic input in the VTA can change cocaine taking. In the current study, the ACh output from the LDTg was attenuated by treatment with the selective muscarinic type 2 (M2) autoreceptor agonist oxotremorine.sesquifumarate (OxoSQ). We hypothesized that OxoSQ would reduce the motivation of rats to self-administer both natural and drug rewards. Animals were tested on progressive ratio (PR) schedules of reinforcement for food pellets and cocaine. On test days, animals on food and on cocaine schedules were bilaterally microinjected prior to the test. Rats received either LDTg OxoSQ infusions or LDTg artificial cerebrospinal fluid (aCSF) infusions in a within-subjects design. In addition, infusions were delivered into a dorsal brain area above the LDTg as an anatomical control region. OxoSQ microinjection in the LDTg, compared to aCSF, significantly reduced both the number of self-administered pellets and cocaine infusions during the initial half of the session; this reduction was dose-dependent. OxoSQ microinjections into the area just dorsal to the LDTg had no significant effect on self-administration of food pellets or cocaine. Animals were also tested in locomotor activity chambers for motor effects following the above microinjections. Locomotor activity was mildly increased by OxoSQ microinjection into the LDTg during the initial half of the session. Overall, these data suggest that LDTg cholinergic neurons play an important role in modifying the reinforcing value of natural and drug rewards. These effects cannot be attributed to significant alterations of locomotor behavior and are likely accomplished through LDTg muscarinic autoreceptors. Published by Elsevier Ltd.

Further study of inversion layer MOS solar cells

NASA Technical Reports Server (NTRS)

Ho, Fat Duen

1987-01-01

A group of inversion layer MOS solar cells has been fabricated. The highest value of open-circuit voltage obtained for the cells is 0.568V. One of the cells has produced a short-circuit current of 79.6 mA and an open-circuit voltage of 0.54V. It is estimated that the actual area AMO efficiency of this cell is 6.6 percent with an assumed value of 0.75 for its fill factor. Efforts made for fabricating an IL/MOS cell with reasonable efficiencies are reported. Future work for 4 sq cm IL cells and 25 sq cm IL cells is discussed.

A Faraday rotation search for magnetic fields in quasar damped Ly alpha absorption systems

NASA Technical Reports Server (NTRS)

Oren, Abraham L.; Wolfe, Arthur M.

1995-01-01

We present the results of a Faraday rotation survey of 61 radio-bright QSOs conducted at the National Radio Astronomy Observatory (NRAO) Very Large Array (VLA). The Galactic contribution to the Faraday rotation is estimated and subtracted to determine the extragalactic rotation measure (RRM) for each source. Eleven of these QSOs are known to exhibit damped Ly alpha absorption. The rate of incidence of significant Faraday rotation of these 11 sources is compared to the remaining 50 and is found to be higher at the 99.8% confidence level. However, as this is based upon only two detections of Faraday rotation in the damped Ly alpha sample, the result is only tentative. If the two detections in the damped Ly alpha sample are dug to the absorbing systems, then the inferred rotation measure induced by these systems is roughly 250 rad/sq m. The two detections were for the two lowest redshift absorbers in the sample. We find that a rotation measure of 250 rad/sq m would have gone undetected for any other absorber in the damped Ly alpha sample due to the 1/(1 + 2) squared dilution of the observed RRM with redshift. Thus the data are consistent with, but do not prove, the hypothesis that Faraday rotation is a generic property of damped Ly alpha absorbers. We do not confirm the suggestion that the amplitude of RRMs increases with redshift. Rather, the data are consistent with no redshift evolution. We find that the uncertainty in the estimation of the Galactic rotation measure (GRM) is a more serious problem than previously realized for extra-galactic Faraday rotation studies of QSO absorbers. A careful analysis of current methods for estimating GRM indicate that it can be determined to an accuracy of about 15 - 20 rad/sq m. Previous studies underestimated this uncertainty by more than a factor of 2. Due to this uncertainty, rotation measures such as we suspect are associated with damped Ly alpha absorption systems can only be detected at redshifts less than z approximately equal 1.

UltraSail - Ultra-Lightweight Solar Sail Concept

NASA Technical Reports Server (NTRS)

Burton, Rodney L.; Coverstone, Victoria L.; Hargens-Rysanek, Jennifer; Ertmer, Kevin M.; Botter, Thierry; Benavides, Gabriel; Woo, Byoungsam; Carroll, David L.; Gierow, Paul A.; Farmer, Greg

2005-01-01

UltraSail is a next-generation high-risk, high-payoff sail system for the launch, deployment, stabilization and control of very large (sq km class) solar sails enabling high payload mass fractions for high (Delta)V. Ultrasail is an innovative, non-traditional approach to propulsion technology achieved by combining propulsion and control systems developed for formation-flying micro-satellites with an innovative solar sail architecture to achieve controllable sail areas approaching 1 sq km, sail subsystem area densities approaching 1 g/sq m, and thrust levels many times those of ion thrusters used for comparable deep space missions. Ultrasail can achieve outer planetary rendezvous, a deep space capability now reserved for high-mass nuclear and chemical systems. One of the primary innovations is the near-elimination of sail supporting structures by attaching each blade tip to a formation-flying micro-satellite which deploys the sail, and then articulates the sail to provide attitude control, including spin stabilization and precession of the spin axis. These tip micro-satellites are controlled by 3-axis micro-thruster propulsion and an on-board metrology system. It is shown that an optimum spin rate exists which maximizes payload mass.

A thermal shield concept for the Solar Probe mission

NASA Technical Reports Server (NTRS)

Miyake, Robert N.; Millard, Jerry M.; Randolph, James E.

1991-01-01

The Solar Probe spacecraft will travel to within 4 solar radii of the sun's center while performing a variety of fundamental experiments in space physics. Exposure to 2900 earth suns (400 W/sq cm) at perihelion imposes severe thermal and material demands on a solar shield system designed to protect the payload that will reside within the shield's shadow envelope or umbra. The design of the shield subsystem is a thermal/materials challenge requiring new technology development. While currently in the preproject study phase, anticipating a 1995 project start, shield preliminary design efforts are currently underway. This paper documents the current status of the mission concept, the materials issues, the configuration concept for the shield subsystem, the current configuration studies performed to date, and the required material testing to provide a database to support a design effort required to develop the shield subsystem.

Change of sleep quality from pre- to 3 years post-solid organ transplantation: The Swiss Transplant Cohort Study

PubMed Central

Denhaerynck, Kris; Huynh-Do, Uyen; Binet, Isabelle; Hadaya, Karine; De Geest, Sabina

2017-01-01

Background Poor sleep quality (SQ) is common after solid organ transplantation; however, very little is known about its natural history. We assessed the changes in SQ from pre- to 3 years post-transplant in adult heart, kidney, liver and lung recipients included in the prospective nation-wide Swiss Transplant Cohort Study. We explored associations with selected variables in patients suffering persistent poor SQ compared to those with good or variable SQ. Methods Adult single organ transplant recipients enrolled in the Swiss Transplant Cohort Study with pre-transplant and at least 3 post-transplant SQ assessment data were included. SQ was self-reported pre-transplant (at listing), then at 6, 12, 24 and 36 months post-transplant. A single SQ item was used to identify poor (0–5) and good sleepers (6–10). Between organ groups, SQ was compared via logistic regression analysis with generalized estimating equations. Within the group reporting persistently poor SQ, we used logistic regression or Kaplan-Meier analysis as appropriate to check for differences in global quality of life and survival. Results In a sample of 1173 transplant patients (age: 52.1±13.2 years; 65% males; 66% kidney, 17% liver, 10% lung, 7% heart) transplanted between 2008 and 2012, pre- transplant poor SQ was highest in liver (50%) and heart (49%) recipients. Overall, poor SQ decreased significantly from pre-transplant (38%) to 24 months post-transplant (26%) and remained stable at 3 years (29%). Patients reporting persistently poor SQ had significantly more depressive symptomatology and lower global quality of life. Conclusion Because self-reported poor SQ is related to poorer global quality of life, these results emphasize the need for further studies to find suitable treatment options for poor SQ in transplant recipients. PMID:29020112

Using the Surprise Question To Identify Those with Unmet Palliative Care Needs in Emergency and Inpatient Settings: What Do Clinicians Think?

PubMed

Haydar, Samir A; Almeder, Lisa; Michalakes, Lauren; Han, Paul K J; Strout, Tania D

2017-07-01

The surprise question (SQ), "Would you be surprised if this patient died within the next year?" is effective in identifying end-stage renal disease and cancer patients at high risk of death and therefore potentially unmet palliative care needs. Following implementation of the SQ in our acute care setting, we sought to explore hospital-based providers' perceptions of the tool. To evaluate (1) providers' perceptions regarding the feasibility of SQ use in emergency and inpatient settings, (2) clinician perceptions regarding the utility of the SQ, and (3) barriers to SQ use. A cross-sectional survey of medical providers following addition of the SQ to the electronic record for all patients admitted to a tertiary care hospital. A total of 111/203 (55%) providers participated: 48/57 (84%) emergency physicians (EPs) and 63/146 (43%) inpatient providers (IPs). Most reported no difficulty using the SQ. Modest numbers in both groups reported that the SQ influenced care delivery (EPs 37%, IPs 42%) as well as goals of care (EPs 45%, IPs 52%). At least some advance care planning discussions were prompted by the SQ (EPs 45%, IPs 58%). Team discussions were influenced by SQ use for more than half of each group. Most respondents (55%) expressed some concern that their SQ responses could be inaccurate. In this setting, clinicians indicated that use of the SQ is feasible, acceptable, and useful in facilitating advance care planning discussions among teams, patients, and families. Many reported that SQ use influenced goals of care, but concern regarding accuracy was a barrier. Additional research examining SQ accuracy and predictive ability is warranted.

An approach for cooling by solar energy

NASA Astrophysics Data System (ADS)

Rabeih, S. M.; Wahhab, M. A.; Asfour, H. M.

The present investigation is concerned with the possibility to base the operation of a household refrigerator on solar energy instead of gas fuel. The currently employed heating system is to be replaced by a solar collector with an absorption area of two sq m. Attention is given to the required changes in the generator design, the solar parameters at the location of refrigerator installation, the mathematical approach for the thermal analysis of the solar collector, the development of a computer program for the evaluation of the important parameters, the experimental test rig, and the measurement of the experimental parameters. A description is given of the obtained optimum operating conditions for the considered system.

Chemical modification of capuramycins to enhance antibacterial activity

PubMed Central

Bogatcheva, Elena; Dubuisson, Tia; Protopopova, Marina; Einck, Leo; Nacy, Carol A.; Reddy, Venkata M.

2011-01-01

Objectives To extend capuramycin spectrum of activity beyond mycobacteria and improve intracellular drug activity. Methods Three capuramycin analogues (SQ997, SQ922 and SQ641) were conjugated with different natural and unnatural amino acids or decanoic acid (DEC) through an ester bond at one or more available hydroxyl groups. In vitro activity of the modified compounds was determined against Mycobacterium spp. and representative Gram-positive and Gram-negative bacteria. Intracellular activity was evaluated in J774A.1 mouse macrophages infected with Mycobacterium tuberculosis (H37Rv). Results Acylation of SQ997 and SQ641 with amino undecanoic acid (AUA) improved in vitro activity against most of the bacteria tested. Conjugation of SQ922 with DEC, but not AUA, improved its activity against Gram-positive bacteria. In the presence of efflux pump inhibitor phenylalanine arginine β-naphthyl amide, MICs of SQ997-AUA, SQ641-AUA and SQ922-DEC compounds improved even further against drug-susceptible and drug-resistant Staphylococcus aureus. In Gram-negative bacteria, EDTA-mediated permeabilization caused 4- to 16-fold enhancement of the activity of AUA-conjugated SQ997, SQ922 and SQ641. Conjugation of all three capuramycin analogues with AUA improved intracellular killing of H37Rv in murine macrophages. Conclusions Conjugation of capuramycin analogues with AUA or DEC enhanced in vitro activity, extended the spectrum of activity in Gram-positive bacteria and increased intracellular activity against H37Rv. PMID:21186194

Numerical simulation of the interaction of transport, diffusion and chemical reactions in an urban plume

NASA Technical Reports Server (NTRS)

Vogel, Bernhard; Vogel, Heike; Fiedler, Franz

1994-01-01

A model system is presented that takes into account the main physical and chemical processes on the regional scale here in an area of 100x100 sq km. The horizontal gridsize used is 2x2 sq km. For a case study, it is demonstrated how the model system can be used to separate the contributions of the processes advection, turbulent diffusion, and chemical reactions to the diurnal cycle of ozone. In this way, typical features which are visible in observations and are reproduced by the numerical simulations can be interpreted.

Electrostatically focused intensified charge coupled devices

NASA Technical Reports Server (NTRS)

Walker, J. W.

1977-01-01

Work performed to develop intensified charge coupled devices (ICCDs) is presented. Four ICCDs, containing 100 x 160 arrays, were fabricated. Electron gains up to 3200 at 15 keV were achieved. Photocathode sensitivities ranged from 190 to 410 micro A/lumen. Dark currents varied from 11 nA/sq cm to 37 nA/sq cm. There was serious concern about the reliability of the bonding scheme for ICCDs due to occassional bond failure. Two solutions to this problem were developed. One involved a modification of the existing bonding technique, and the other was the development of a protected bond pad employing a barrier metal between the aluminum metallization and the gold bond wire. An accumulation process was characterized with respect to its most critical variable. This characterization led to the achievement of reproducible spectral response and the discovery and elimination of dark current increase associated with this process.

Solid Polymer Electrolyte (SPE) fuel cell technology program

NASA Technical Reports Server (NTRS)

1978-01-01

Many previously demonstrated improved fuel cell features were consolidated to (1) obtain a better understanding of the observed characteristics of the operating laboratory-sized cells; (2) evaluate appropriate improved fuel cell features in 0.7 sq ft cell hardware; and (3) study the resultant fuel cell capability and determine its impact on various potential fuel cell space missions. The observed performance characteristics of the fuel cell at high temperatures and high current densities were matched with a theoretical model based on the change in Gibbs free energy voltage with respect to temperature and internal resistance change with current density. Excellent agreement between the observed and model performance was obtained. The observed performance decay with operational time on cells with very low noble metal loadings (0.05 mg/sq cm) were shown to be related to loss in surface area. Cells with the baseline amount of noble catalyst electrode loading demonstrated over 40,000 hours of stable performance.

Photoelectrolysis of water at high current density - Use of laser light excitation of semiconductor-based photoelectrochemical cells

NASA Technical Reports Server (NTRS)

Wrighton, M. S.; Bocarsley, A. B.; Bolts, J. M.

1978-01-01

In the present paper, some results are given for UV laser light irradiation of the photoanode (SnO2, SrTiO3, or TiO2) in a cell for the light-driven electrolysis of H2O, at radiation intensities of up to 380 W/sq cm. The properties of the anode material are found to be independent of light intensity. Conversion of UV light to stored chemical energy in the form of 2H2/O2 from H2O was driven at a rate of up to 30 W/sq cm. High O2 evolution rates at the irradiated anodes without changes in the current-voltage curves are attributed to the excess oxidizing power associated with photogenerated holes. A test for this sort of hypothesis for H2 evolution at p-type materials is proposed.

Top-of-Atmosphere Direct Radiative Effect of Aerosols from the Clouds and the Earth's Radiant Energy System Satellite Instrument (CERES)

NASA Technical Reports Server (NTRS)

Loeb, N. G.; Kato, S.

2002-01-01

Nine months of CERES/TRMM broadband fluxes combined with VIRS high-resolution imager measurements are used to estimate the daily average direct radiative effect of aerosols for clear-sky conditions over the tropical oceans. On average, aerosols have a cooling effect over the tropics of 4.6 +/- 1 W/sq m. The magnitude is approx.2 W/sq m smaller over the southern tropical oceans than it is over northern tropical oceans. The direct effect derived from CERES is highly correlated with coincident aerosol optical depth retrievals inferred from 0.63 microns VIRS radiances (correlation coefficient of 0.96). The slope of the regression line is approx. -32 W/sq m/t over the equatorial Pacific Ocean, but changes both regionally and seasonally, depending on the aerosol characteristics. Near sources of biomass burning and desert dust, the aerosol direct effect reaches -25 W sq m to -30 W/sq m. The direct effect from CERES also shows a dependence on wind speed. The reason for this dependence is unclear-it may be due to increased aerosol (e.g. sea-salt or aerosol transport) or increased surface reflection (e.g. due to whitecaps). The uncertainty in the tropical average direct effect from CERES is approx. 1 W/sq m (approx. 20%) due mainly to cloud contamination, the radiance-to-flux conversion, and instrument calibration. By comparison, uncertainties in the direct effect from the ERBE and CERES "ERBE-Like" products are a factor of 3 to 5 larger.

ALK-rearranged lung squamous cell carcinoma responding to alectinib: a case report and review of the literature.

PubMed

Mamesaya, Nobuaki; Nakashima, Kazuhisa; Naito, Tateaki; Nakajima, Takashi; Endo, Masahiro; Takahashi, Toshiaki

2017-07-06

Although anaplastic lymphoma kinase (ALK) fusion genes are generally identified in lung adenocarcinoma patients, they are relatively rare in patients with squamous cell carcinoma (SqCC). Metastatic ALK-rearranged lung adenocarcinoma patients treated with ALK inhibitors demonstrate higher response rates, improved progression-free survival, and reduced toxicity relative to those treated with conventional chemotherapy regimens. However, the efficacy of treatment with ALK inhibitors in patients with ALK-rearranged lung SqCC remains unknown. We discuss a 52-year-old Japanese-Brazilian woman without a history of smoking who was referred to our hospital for evaluation of severe left back pain and a left hilar mass observed on a chest radiograph. The patient was eventually diagnosed on the basis of computed tomography, pathological, and immunohistochemical findings as having Stage IV lung SqCC. First-line treatment with palliative radiotherapy and systemic chemotherapy with cisplatin plus vinorelbine was administered, but was not effective. ALK testing was subsequently performed, revealing positive ALK expression and gene rearrangement. Alectinib therapy was then initiated, which resulted in a gradual, but substantial reduction in tumor size. To the best of our knowledge, this is the first case report to discuss the successful management of ALK-rearranged lung SqCC with alectinib. We propose that molecular testing for driver mutations should be considered in young patients with a light or no smoking history, even if the histological findings correspond with SqCC, and alectinib therapy represents a reasonable option in cases of ALK-rearranged lung SqCC.

New molecular assemblies of redox isomers, [CrIII(X4SQ)3-n(X4Cat)n]-n (X = Cl and Br; n = 0, 1, and 2), with metallocenium cations, [MIIICp2]+ (M = Co and Fe): X-ray crystal structures and physical properties.

PubMed

Chang, H C; Miyasaka, H; Kitagawa, S

2001-01-01

A series of redox isomers of [CrIII(X4SQ)(X4Cat)2]2-, [CrIII(X4SQ)2(X4Cat)]-, and [CrIII(X4SQ)3]0 (X = Cl and Br, SQ = semiquinonate, and Cat = catecholate) have been synthesized and characterized as charge-transfer (CT) compounds with metallocenium cations: (CoIIICp2)2[CrIII(Cl4SQ)(Cl4Cat)2] (1), (CoIIICp2)2[CrIII(Br4SQ)(Br4Cat)2] (2), (FeIIICp2)[CrIII(Cl4SQ)2(Cl4Cat)].C6H6 (4), (FeIIICp2)[CrIII(Br4SQ)2(Br4Cat)].CS2 (5), and (FeIIICp2)[CrIII(Cl4SQ)2(Cl4Cat)][CrIII(Cl4SQ)3] (6). First, the oxidation states of the chromium complexes are strongly dependent on the redox potentials of the metallocenes used. The CoIICp2, exhibiting stronger reduction power than FeIICp2, is useful for two-electron reduction of the [CrIII(X4SQ)3]0, affording [CrIII(X4SQ)(X4Cat)2]2- (1 and 2), which are first isolated and crystallographically characterized in the solid state. In contrast the reaction with FeIICp2 affords only [CrIII(X4SQ)2(X4Cat)]- (4 and 5). Second, solvents influence crystal structures of these compounds. The solvent set of C6H6/CS2 gives 1:1:C6H6 compound 4 with unique charged anions, [CrIII(Cl4SQ)2(Cl4Cat)]-, while the other set, n-C6H12/CS2, affords 1:2 compound 6 including the two redox isomers, [CrIII(Cl4SQ)2(Cl4Cat)]- and [CrIII(Cl4SQ)3]0. The [CrIII(X4SQ)(X4Cat)2]2- anions in 1 and 2 show no significant interconnection between them (discrete type), while the [CrIII(X4SQ)2(X4Cat)]- anions in 4-6 show one-dimensional column-type structures with the aid of intermolecular stacking interactions of the ligand moieties. The anions in 4 show additional stacking interaction with the [FeIIICp2]+ to form one-dimensional ...[D][A][S][D][A]... (D = [FeIIICp2]+, A = [CrIII(Cl4SQ)2(Cl4Cat)]-, and S = C6H6) type mixed-stack arrangements similar to that of previously reported (CoIIICp2)[CrIII(Cl4SQ)2(Cl4Cat)].C6H6 (3). Compound 6 forms a two-dimensional sheet structure where the two redox isomers, [CrIII(Cl4SQ)2(Cl4Cat)]- and [CrIII(Cl4SQ)3]0, are included. The sheet is regarded as a mixed-valence molecular assembly. Two types of the anions, [CrIII(X4SQ)(X4Cat)2]2- (1 and 2) and [CrIII(X4SQ)2(X4Cat)]- (4-6), exhibiting an intramolecular mixed-valence state, show intramolecular intervalence CT transition (IVCT) from the Cat to the SQ at near 5800 and 4300 cm-1, respectively, both in the solution and in the solid states. The intermolecular mixed-valence state of 6 was characterized by absorption spectroscopy, electric conductivity, and SQUID magnetometry. Interestingly, this mixed-valence state of the chromium module is dependent on the redox active nature of the coordinated ligands.

The Magsat precision vector magnetometer

NASA Technical Reports Server (NTRS)

Acuna, M. H.

1980-01-01

This paper examines the Magsat precision vector magnetometer which is designed to measure projections of the ambient field in three orthogonal directions. The system contains a highly stable and linear triaxial fluxgate magnetometer with a dynamic range of + or - 2000 nT (1 nT = 10 to the -9 weber per sq m). The magnetometer electronics, analog-to-digital converter, and digitally controlled current sources are implemented with redundant designs to avoid a loss of data in case of failures. Measurements are carried out with an accuracy of + or - 1 part in 64,000 in magnitude and 5 arcsec in orientation (1 arcsec = 0.00028 deg).

Comparison of four morphometric definitions and a semiquantitative consensus reading for assessing prevalent vertebral fractures.

PubMed

Grados, F; Roux, C; de Vernejoul, M C; Utard, G; Sebert, J L; Fardellone, P

2001-01-01

The assessment of vertebral fracture in patients with osteoporosis by conventional radiography has been improved over the past 10 years using either the semiquantitative (SQ) method devised by Genant et al. or quantitative morphometry. However, there is still no internationally agreed definition for vertebral fracture and there have been few comparative studies between these different approaches. Our study assessed the reproducibility of the SQ method and of four commonly used morphometric algorithms (Melton's, Eastell's, Minne's and McCloskey's methods) for assessing prevalent vertebral fractures, and examined the agreement of each morphometric algorithm with a SQ consensus reading performed by three experts. With this consensus reading in place of a gold standard, we determined relative measures of sensitivity, specificity and optimal cutoff threshold for each morphometric algorithm. The study was conducted in 39 postmenopausal women who had at least one osteoporotic vertebral fracture. Normal values were derived from 84 healthy postmenopausal women with apparently normal vertebral bodies. Our results indicate that the concordance of SQ method was excellent (intraobserver agreement on serial radiographs = 96.4%, kappa = 0.91; agreement between individual readings and the consensus reading = 98%, kappa = 0.95). Three morphometric approaches demonstrated good intra- and interobserver concordance (Melton: intraobserver agreement on serial radiographs = 92.7%, kappa = 0.82, interobserver agreement = 91.1%, kappa = 0.79; Eastell: intraobserver agreement on serial radiographs = 87.6%, kappa = 0.66, interobserver agreement = 88.6%, kappa = 0.68; McCloskey: intraobserver agreement on serial radiographs = 91.5%, kappa = 0.72, interobserver agreement = 93.9%, kappa = 0.78). Except for McCloskey's method, the optimal cutoff thresholds defined in our study by highest kappa score or Youden index in comparison with the SQ consensus reading were near the cutoff thresholds that were arbitrarily fixed. The four morphometric algorithms provided a good agreement with the results of the SQ consensus reading, but the more complex algorithm did not provide better results and even if we adjusted the cutoff threshold, no morphometric algorithm agreed perfectly with the SQ consensus reading. We conclude that morphometric approaches currently used should not be employed alone to detect prevalent vertebral fractures in studies on osteoporosis, but should rather be used in combination with a visual assessment. The SQ approach that allows differential diagnosis of vertebral deformities and has demonstrated a better reproducibility can be employed alone when it is performed by experienced and well-trained readers.

Test results of a pumped two-phase mounting plate with ammonia. [designed for spacecraft thermal control

NASA Technical Reports Server (NTRS)

Swanson, T. D.; Mccabe, M. E., Jr.; Grote, M. G.

1987-01-01

The design, fabrication, and testing of full-scale prototype units of a two-phase mounting plate (TPMP), which will be used in a two-phase ammonia-based thermal control system for a large spacecraft, are described. The mounting plate uses an evaporator design in which liquid is mechanically pumped through porous feed tubes within the plate. The prototype TPMPs were tested with ammonia at heat loads over 3000 W (3.2 W/sq cm) and local heat fluxes of up to 4 W/sq cm. Calculated total heat transfer coefficients from these tests were between 0.8 and 1.0 W/sq cm per C. This represents a better than twenty-fold improvement over comparable single-phase heat transfer coefficients. Design diagrams are included.

Foil bearings for axial and radial support of high speed rotors: Design, development, and determination of operating characteristics

NASA Technical Reports Server (NTRS)

Licht, L.

1978-01-01

Flexible surface thrust and journal foil bearings were fabricated, and their performance was demonstrated, both individually and jointly as a unified rotor support system. Experimental results are documented with graphs and oscilloscopic data of trajectories, waveforms, and scans of amplitude response. At speeds of 40,000 to 45,000 rpm and a mean clearance of the order of 15 to 20 micrometers (600 to 800 micrometers, the resilient, air lubricated, spiral groove thrust bearings support a load of 127 N (29 lb; 13 kgf), equivalent to 3.0 N/sq cm (4.5 lb/sq in 0.31 kgf sq cm). Journal bearings with polygonal sections provided stable and highly damped supports at speeds up to 50,000 rpm.

Design of a photovoltaic system for a southeast all-electric residence

NASA Astrophysics Data System (ADS)

Mehalick, E. M.; Tully, G. F.; Johnson, J.; Truncellito, N.; Schaeffer, R.; Parker, J.

1982-01-01

A photovoltaic system was developed and integrated into a single-story residence suitable for the Southeast region of the country. The design addresses an integral mounted array which displaces conventional roof sheathing, roofing felt and shingles. The array has a rated power output of 5.6 kW and covers 86 sq.m. of roof area. A 6 kW utility-tied inverter is used in the power conversion subsystem, representative of a lower cost version, currently available hardware. The system provides feedback of excess energy to the utility, which is the most promising approach for grid-connected systems in the mid-1980's. The complete system and house design are described, including all the pertinent installation and construction drawings. Specific performance results are presented for the Miami, Florida, and Charleston, SC, regions.

Funduscopic alterations in the rhesus monkey induced by exposure to heavy ions /0+8/ 250 MeV/nucleon

NASA Technical Reports Server (NTRS)

Beckman, F. N.; Bonney, C. H.; Hunter, D. M.

1974-01-01

A heavy-ion, high-energy beam has been extracted from the Lawrence Radiation Laboratory Bevatron, making controlled exposure of biological systems feasible, and a series of experiments have been undertaken to determine the possible deleterious effects of such irradiation upon the primate retina. The left eyes of 54 rhesus monkeys have been exposed to accelerated 0+8 (250 MeV/nucleon). Beam flux ranged from 1.3 x 10 to the 7th particles/ sq cm (171 rads) to 5.9 x 10 to the 8th particles/sq cm (7740 rads). Fundus photography was performed immediately prior to and immediately following exposure, at 24 to 48 hours postexposure and at 1, 2, and 5 weeks postexposure. Punctate hemorrhages of the retina were visible at 1.3 x 10 to the 7th particles/sq cm (171 rads), the lowest exposure level utilized in this study. Acute radiation retinopathy, consisting of geographic retinal hemorrhage and ischemic necrosis of the retina, was not seen until total flux reached 7.7 x 10 to the 7th particles/sq cm (1000 rads).

Multi-Level Scenario Module 1: 7th Division

DTIC Science & Technology

2009-03-01

MQ1B Recon Sq 1x RC135S Recon Sq 5x RC135VW Cythera Paros Shaw Peterson Fighter Sq 24x F16CD BLK-50 Fighter Sq 24x F15E Fighter Sq 24x A/0A10A Airlift Sq...Mountain Home Amphibious Assault Ship, Multipurpose (LHD) Amphibious Transport Dock (LPD) Dock Landing Ship ( LSD ) Guided Missile Cruiser (CG...Destroyer (DDG) x2 Submarine, Nuclear Powered (SSN) x 6 Guided Missile Submarine, Nuclear Powered (SSGN) Cythera Paros Shaw Peterson Guided

Ghanaian parents' perceptions of pre and postnatal nutrient supplements and their effects.

PubMed

Adams, Katherine P; Okronipa, Harriet; Adu-Afarwuah, Seth; Arimond, Mary; Kumordzie, Sika; Oaks, Brietta M; Ocansey, Maku E; Young, Rebecca R; Vosti, Stephen A; Dewey, Kathryn G

2018-04-15

Small-quantity lipid-based nutrient supplements (SQ-LNS) have been studied in efficacy and effectiveness trials, but little is known about how parents perceive the products and their effects. In a randomised trial in Ghana, efficacy of SQ-LNS provided to women during pregnancy and the first 6 months postpartum and to their children from 6 to 18 months of age was assessed by comparison with iron-folic acid (IFA) capsules and multiple micronutrient (MMN) capsules provided to women. In a follow-up study conducted when the index children from the original trial were between 4 and 6 years of age, we used survey-based methods to assess retrospective and current parental perceptions of nutrient supplements generally and of SQ-LNS and their effects compared with perceptions IFA and MMN capsules. Most parents perceived that the assigned supplements (SQ-LNS, IFA, or MMN) positively impacted the mother during pregnancy (approximately 89% of both mothers and fathers) and during lactation (84% of mothers and 86% of fathers). Almost all (≥90%) of mothers and fathers perceived that the assigned supplement positively impacted the index child and expected continued positive impacts on the child's health and human capital into the future. A smaller percentage of parents perceived negative impacts of the supplements (7%-17% of mothers and 4%-12% of fathers). Perceptions of positive impacts and of negative impacts did not differ by intervention group. The results suggest that similar populations would likely be receptive to programs to deliver SQ-LNS or micronutrient capsules. © 2018 The Authors. Maternal and Child Nutrition Published by John Wiley & Sons, Ltd.

Material growth and characterization for solid state devices

NASA Technical Reports Server (NTRS)

Stefanakos, E. K.; Collis, W. J.; Abul-Fadl, A.; Iyer, S.

1984-01-01

During the reporting period, InGaAs was grown on Fe-doped (semi-insulating) (100) InP substrates by current controlled liquid phase epitaxy (CCLPE) at 640 C and current densities of 2.5A sq/cm to 5 A/sq cm for periods from 5 to 30 minutes. Special efforts were made to reduce the background carrier concentration in the grown layers as much as possible. The best layers exhibited carrier concentrations in the mid-10 to the 15th power/cu cm range and up to 10,900 sq cm/V-sec room temperature mobility. InGaAsP quaternary layers of energy gap corresponding to wavelengths of approximately 1.5 microns and 1.3 microns were grown on (100) InP substrates by CCLPE. In the device fabrication area, work was directed toward processing MISFET's using InGaAs. SiO2, Si3N4 and Al2O3 were deposited by ion beam sputtering, electron beam evaporation and chemical vapor reaction on Si, GaAs, and InGaAs substrates. SiO2 and Si3N4 sputtered layers were found to possess a high density of pinhole defects that precluded capacitance-voltage analysis. Chemical vapor deposited Al2O3 layers on Si, GaAs and InGaAs substrates also exhibited a large number of pinhole defects. This prevented achieving good MIS devices over most of the substrate surface area.

Industrial ion source technology

NASA Technical Reports Server (NTRS)

Kaufman, H. R.; Robinson, R. S.

1979-01-01

In reactive ion etching of Si, varying amounts of O2 were added to the CF4 background. The experimental results indicated an etch rate less than that for Ar up to an O2 partial pressure of about .00006 Torr. Above this O2 pressure, the etch rate with CF4 exceeded that with Ar alone. For comparison the random arrival rate of O2 was approximately equal to the ion arrival rate at a partial pressure of about .00002 Torr. There were also ion source and ion pressure gauge maintenance problems as a result of the use of CF4. Large scale (4 sq cm) texturing of Si was accomplished using both Cu and stainless steel seed. The most effective seeding method for this texturing was to surround the sample with large inclined planes. Designing, fabricating, and testing a 200 sq cm rectangular beam ion source was emphasized. The design current density was 6 mA/sq cm with 500 eV argon ions, although power supply limitations permitted operation to only 2 mA/sq cm. The use of multiple rectangular beam ion sources for continuous processing of wider areas than would be possible with a single source was also studied. In all cases investigated, the most uniform coverage was obtained with 0 to 2 cm beam overlay. The maximum departure from uniform processing at optimum beam overlap was found to be +15%.

Sequential Processing for Organic Photovoltaics: Design Rules for Morphology Control by Tailored Semi-Orthogonal Solvent Blends

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aguirre, Jordan C.; Hawks, Steven A.; Ferreira, Amy S.

2015-03-18

Design rules are presented for significantly expanding sequential processing (SqP) into previously inaccessible polymer:fullerene systems by tailoring binary solvent blends for fullerene deposition. Starting with a base solvent that has high fullerene solubility, 2-chlorophenol (2-CP), ellipsometry-based swelling experiments are used to investigate different co-solvents for the fullerene-casting solution. By tuning the Flory-Huggins χ parameter of the 2-CP/co-solvent blend, it is possible to optimally swell the polymer of interest for fullerene interdiffusion without dissolution of the polymer underlayer. In this way solar cell power conversion efficiencies are obtained for the PTB7 (poly[(4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b']dithiophene-2,6-diyl)(3-fluoro-2-[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl)]) and PC61BM (phenyl-C61-butyric acid methyl ester) materials combination thatmore » match those of blend-cast films. Both semicrystalline (e.g., P3HT (poly(3-hexylthiophene-2,5-diyl)) and entirely amorphous (e.g., PSDTTT (poly[(4,8-di(2-butyloxy)benzo[1,2-b:4,5-b']dithiophene-2,6-diyl)-alt-(2,5-bis(4,4'-bis(2-octyl)dithieno[3,2-b:2'3'-d]silole-2,6-diyl)thiazolo[5,4-d]thiazole)]) conjugated polymers can be processed into highly efficient photovoltaic devices using the solvent-blend SqP design rules. Grazing-incidence wide-angle x-ray diffraction experiments confirm that proper choice of the fullerene casting co-solvent yields well-ordered interdispersed bulk heterojunction (BHJ) morphologies without the need for subsequent thermal annealing or the use of trace solvent additives (e.g., diiodooctane). The results open SqP to polymer/fullerene systems that are currently incompatible with traditional methods of device fabrication, and make BHJ morphology control a more tractable problem.« less

Aerothermodynamic Environments Definition for the Mars Science Laboratory Entry Capsule

NASA Technical Reports Server (NTRS)

Edquist, Karl T.; Dyakonov, Artem A.; Wright, Michael J.; Tang, Chun Y.

2007-01-01

An overview of the aerothermodynamic environments definition status is presented for the Mars Science Laboratory entry vehicle. The environments are based on Navier-Stokes flowfield simulations on a candidate aeroshell geometry and worst-case entry heating trajectories. Uncertainties for the flowfield predictions are based primarily on available ground data since Mars flight data are scarce. The forebody aerothermodynamics analysis focuses on boundary layer transition and turbulent heating augmentation. Turbulent transition is expected prior to peak heating, a first for Mars entry, resulting in augmented heat flux and shear stress at the same heatshield location. Afterbody computations are also shown with and without interference effects of reaction control system thruster plumes. Including uncertainties, analysis predicts that the heatshield may experience peaks of 225 W/sq cm for turbulent heat flux, 0.32 atm for stagnation pressure, and 400 Pa for turbulent shear stress. The afterbody heat flux without thruster plume interference is predicted to be 7 W/sq cm on the backshell and 10 W/sq cm on the parachute cover. If the reaction control jets are fired near peak dynamic pressure, the heat flux at localized areas could reach as high as 76 W/sq cm on the backshell and 38 W/sq cm on the parachute cover, including uncertainties. The final flight environments used for hardware design will be updated for any changes in the aeroshell configuration, heating design trajectories, or uncertainties.

A regional comparison of solar, heat pump, and solar-heat pump systems

NASA Astrophysics Data System (ADS)

Manton, B. E.; Mitchell, J. W.

1982-08-01

A comparative study of the thermal and economic performance of the parallel and series solar heat pump systems, stand alone solar and stand alone heat pump systems for residential space and domestic hot water heating for the U.S. using FCHART 4.0 is presented. Results show that the parallel solar heat pump system yields the greatest energy savings in the south. Very low cost collectors (50-150 dollars/sq m) are required for a series solar heat pump system in order for it to compete economically with the better of the parallel or solar systems. Conventional oil or gas furnaces need to have a seasonal efficiency of at least 70-85% in order to save as much primary energy as the best primary system in the northeast. In addition, the implications of these results for current or proposed federal tax credit measures are discussed.

Performance of all-NbN superconductive tunnel junctions as mixers at 205 GHz

NASA Technical Reports Server (NTRS)

Mcgrath, W. R.; Leduc, H. G.; Stern, J. A.

1990-01-01

Small-area (1x1 sq micron) high-current-density NbN-MgO-NbN tunnel junctions with I-V characteristics suitable for high frequency mixers were fabricated. These junctions are integrated with superconducting microstrip lines designed to resonate out the large junction capacitance. The mixer gain and noise performance were studied near 205 GHz as a function of the inductance provided by the microstrip. This has yielded values of junction capacitance of 85 fF/sq microns and magnetic penetration depth of 3800 angstroms. Mixer noise as low as 133 K has been obtained for properly tuned junctions. This is the best noise performance ever reported for an NbN SIS mixer.

An Opportunistic Search for Extraterrestrial Intelligence (SETI) with the Murchison Widefield Array

NASA Astrophysics Data System (ADS)

Tingay, S. J.; Tremblay, C.; Walsh, A.; Urquhart, R.

2016-08-01

A spectral line image cube generated from 115 minutes of MWA data that covers a field of view of 400 sq, deg. around the Galactic Center is used to perform the first Search for ExtraTerrestrial Intelligence (SETI) with the Murchison Widefield Array (MWA). Our work constitutes the first modern SETI experiment at low radio frequencies, here between 103 and 133 MHz, paving the way for large-scale searches with the MWA and, in the future, the low-frequency Square Kilometre Array. Limits of a few hundred mJy beam-1 for narrowband emission (10 kHz) are derived from our data, across our 400 sq. deg. field of view. Within this field, 45 exoplanets in 38 planetary systems are known. We extract spectra at the locations of these systems from our image cube to place limits on the presence of narrow line emission from these systems. We then derive minimum isotropic transmitter powers for these exoplanets; a small handful of the closest objects (10 s of pc) yield our best limits of order 1014 W (Equivalent Isotropic Radiated Power). These limits lie above the highest power directional transmitters near these frequencies currently operational on Earth. A SETI experiment with the MWA covering the full accessible sky and its full frequency range would require approximately one month of observing time. The MWA frequency range, its southern hemisphere location on an extraordinarily radio quiet site, its very large field of view, and its high sensitivity make it a unique facility for SETI.

Reduction, analysis, and properties of electric current systems in solar active regions

NASA Technical Reports Server (NTRS)

Gary, G. Allen; Demoulin, Pascal

1995-01-01

The specific attraction and, in large part, the significance of solar magnetograms lie in the fact that they give the most important data on the electric currents and the nonpotentiality of active regions. Using the vector magnetograms from the Marshall Space Flight Center (MSFC), we employ a unique technique in the area of data analysis for resolving the 180 deg ambiguity in order to calculate the spatial structure of the vertical electric current density. The 180 deg ambiguity is resolved by applying concepts from the nonlinear multivariable optimization theory. The technique is shown to be of particular importance in very nonpotential active regions. The characterization of the vertical electric current density for a set of vector magnetograms using this method then gives the spatial scale, locations, and magnitude of these current systems. The method, which employs an intermediate parametric function which covers the magnetogram and which defines the local `preferred' direction, minimizes a specific functional of the observed transverse magnetic field. The specific functional that is successful is the integral of the square of the vertical current density. We find that the vertical electric current densities have common characteristics for the extended bipolar (beta) (gamma) (delta)-regions studied. The largest current systems have j(sub z)'s which maximizes around 30 mA/sq m and have a linear decreasing distribution to a diameter of 30 Mn.

SQDFT: Spectral Quadrature method for large-scale parallel O ( N ) Kohn–Sham calculations at high temperature

DOE Office of Scientific and Technical Information (OSTI.GOV)

Suryanarayana, Phanish; Pratapa, Phanisri P.; Sharma, Abhiraj

We present SQDFT: a large-scale parallel implementation of the Spectral Quadrature (SQ) method formore » $$\\mathscr{O}(N)$$ Kohn–Sham Density Functional Theory (DFT) calculations at high temperature. Specifically, we develop an efficient and scalable finite-difference implementation of the infinite-cell Clenshaw–Curtis SQ approach, in which results for the infinite crystal are obtained by expressing quantities of interest as bilinear forms or sums of bilinear forms, that are then approximated by spatially localized Clenshaw–Curtis quadrature rules. We demonstrate the accuracy of SQDFT by showing systematic convergence of energies and atomic forces with respect to SQ parameters to reference diagonalization results, and convergence with discretization to established planewave results, for both metallic and insulating systems. Here, we further demonstrate that SQDFT achieves excellent strong and weak parallel scaling on computer systems consisting of tens of thousands of processors, with near perfect $$\\mathscr{O}(N)$$ scaling with system size and wall times as low as a few seconds per self-consistent field iteration. Finally, we verify the accuracy of SQDFT in large-scale quantum molecular dynamics simulations of aluminum at high temperature.« less

Attenuation of Typical Sex Differences in 800 Adults with Autism vs. 3,900 Controls

PubMed Central

Baron-Cohen, Simon; Cassidy, Sarah; Auyeung, Bonnie; Allison, Carrie; Achoukhi, Maryam; Robertson, Sarah; Pohl, Alexa; Lai, Meng-Chuan

2014-01-01

Sex differences have been reported in autistic traits and systemizing (male advantage), and empathizing (female advantage) among typically developing individuals. In individuals with autism, these cognitive-behavioural profiles correspond to predictions from the “extreme male brain” (EMB) theory of autism (extreme scores on autistic traits and systemizing, below average on empathizing). Sex differences within autism, however, have been under-investigated. Here we show in 811 adults (454 females) with autism and 3,906 age-matched typical control adults (2,562 females) who completed the Empathy Quotient (EQ), the Systemizing Quotient-Revised (SQ-R), and the Autism Spectrum Quotient (AQ), that typical females on average scored higher on the EQ, typical males scored higher on the SQ-R and AQ, and both males and females with autism showed a shift toward the extreme of the “male profile” on these measures and in the distribution of “brain types” (the discrepancy between standardized EQ and SQ-R scores). Further, normative sex differences are attenuated but not abolished in adults with autism. The findings provide strong support for the EMB theory of autism, and highlight differences between males and females with autism. PMID:25029203

SQDFT: Spectral Quadrature method for large-scale parallel O ( N ) Kohn–Sham calculations at high temperature

DOE PAGES

Suryanarayana, Phanish; Pratapa, Phanisri P.; Sharma, Abhiraj; ...

2017-12-07

We present SQDFT: a large-scale parallel implementation of the Spectral Quadrature (SQ) method formore » $$\\mathscr{O}(N)$$ Kohn–Sham Density Functional Theory (DFT) calculations at high temperature. Specifically, we develop an efficient and scalable finite-difference implementation of the infinite-cell Clenshaw–Curtis SQ approach, in which results for the infinite crystal are obtained by expressing quantities of interest as bilinear forms or sums of bilinear forms, that are then approximated by spatially localized Clenshaw–Curtis quadrature rules. We demonstrate the accuracy of SQDFT by showing systematic convergence of energies and atomic forces with respect to SQ parameters to reference diagonalization results, and convergence with discretization to established planewave results, for both metallic and insulating systems. Here, we further demonstrate that SQDFT achieves excellent strong and weak parallel scaling on computer systems consisting of tens of thousands of processors, with near perfect $$\\mathscr{O}(N)$$ scaling with system size and wall times as low as a few seconds per self-consistent field iteration. Finally, we verify the accuracy of SQDFT in large-scale quantum molecular dynamics simulations of aluminum at high temperature.« less

Malaspina Glacier

NASA Image and Video Library

2017-12-08

NASA image captured August 31, 2000 The tongue of the Malaspina Glacier, the largest glacier in Alaska, fills most of this image. The Malaspina lies west of Yakutat Bay and covers 1,500 sq. MI (3,880 sq. km). Credit: NASA/Landsat NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Join us on Facebook

Particle distributions in approximately 10(13) - 10(16) eV air shower cores at mountain altitude and comparison with Monte Carlo simulations

NASA Technical Reports Server (NTRS)

Ash, A. G.

1985-01-01

Photographs of 521 shower cores in an array of current-limited spark (discharge) chambers at Sacramento Peak (2900m above sea level, 730 g /sq cm.), New Mexico, U.S.A., have been analyzed and the results compared with similar data from Leeds (80m above sea level, 1020 g sq cm.). It was found that the central density differential spectrum is consistent with a power law index of -2 up to approx. 1500/sq m where it steepens, and that shower cores become flatter on average with increasing size. Scaling model predictions for proton primaries with a approx E sup -2.71 energy spectrum account well for the altitude dependence of the data at lower densities. However, deviations at higher densities indicate a change in hadron interaction characteristics between approx few x 10 to the 14th power and 10 to the 15th power eV primary energy causing particles close to the shower axis to be spread further out.

Scale up of large ALON® and spinel windows

NASA Astrophysics Data System (ADS)

Goldman, Lee M.; Kashalikar, Uday; Ramisetty, Mohan; Jha, Santosh; Sastri, Suri

2017-05-01

Aluminum Oxynitride (ALON® Transparent Ceramic) and Magnesia Aluminate Spinel (Spinel) combine broadband transparency with excellent mechanical properties. Their cubic structure means that they are transparent in their polycrystalline form, allowing them to be manufactured by conventional powder processing techniques. Surmet has scaled up its ALON® production capability to produce and deliver windows as large as 4.4 sq ft. We have also produced our first 6 sq ft window. We are in the process of producing 7 sq ft ALON® window blanks for armor applications; and scale up to even larger, high optical quality blanks for Recce window applications is underway. Surmet also produces spinel for customers that require superior transmission at the longer wavelengths in the mid wave infra-red (MWIR). Spinel windows have been limited to smaller sizes than have been achieved with ALON. To date the largest spinel window produced is 11x18-in, and windows 14x20-in size are currently in process. Surmet is now scaling up its spinel processing capability to produce high quality window blanks as large as 19x27-in for sensor applications.

Near-IR squaraine dye–loaded gated periodic mesoporous organosilica for photo-oxidation of phenol in a continuous-flow device

PubMed Central

Borah, Parijat; Sreejith, Sivaramapanicker; Anees, Palapuravan; Menon, Nishanth Venugopal; Kang, Yuejun; Ajayaghosh, Ayyappanpillai; Zhao, Yanli

2015-01-01

Periodic mesoporous organosilica (PMO) has been widely used for the fabrication of a variety of catalytically active materials. We report the preparation of novel photo-responsive PMO with azobenzene-gated pores. Upon activation, the azobenzene gate undergoes trans-cis isomerization, which allows an unsymmetrical near-infrared squaraine dye (Sq) to enter into the pores. The gate closure by cis-trans isomerization of the azobenzene unit leads to the safe loading of the monomeric dye inside the pores. The dye-loaded and azobenzene-gated PMO (Sq-azo@PMO) exhibits excellent generation of reactive oxygen species upon excitation at 664 nm, which can be effectively used for the oxidation of phenol into benzoquinone in aqueous solution. Furthermore, Sq-azo@PMO as the catalyst was placed inside a custom-built, continuous-flow device to carry out the photo-oxidation of phenol to benzoquinone in the presence of 664-nm light. By using the device, about 23% production of benzoquinone with 100% selectivity was achieved. The current research presents a prototype of transforming heterogeneous catalysts toward practical use. PMID:26601266

Equatorial electrojet and its response to external electromagnetic effects

NASA Astrophysics Data System (ADS)

Bespalov, P. A.; Savina, O. N.

2012-09-01

In the quiet low-latitude Earth's ionosphere, a sufficiently developed current system that is responsible for the Sq magnetic-field variations is formed in quiet Sun days under the action of tidal streams. The density of the corresponding currents is maximum in the midday hours at the equatorial latitudes, where the so-called equatorial electrojet is formed. In this work, we discuss the nature of the equatorial electrojet. This paper studies the value of its response to external effects. First of all, it is concerned with estimating the possibility of using the equatorial electrojet for generating low-frequency electromagnetic signals during periodic heating of the ionosphere by the heating-facility radiation. The equatorial electrojet can also produce electrodynamic response to the natural atmospheric processes, e.g., an acoustic-gravity wave.

Design of high-voltage, high-power, solid state remote power controllers for aerospace applications

NASA Technical Reports Server (NTRS)

Sturman, J. C.

1985-01-01

Two general types of remote power controllers (RPC's), which combine the functions of a circuit breaker and a switch, were developed for use in dc aerospace systems. Power-switching devices used in the designs are the gate-turnoff thyristor (GTO) and MOSFET. The RPC's can switch dc voltages to 1200 V and currents to 1000 A. Seven different units were constructed and subjected to laboratory and thermal vacuum testing. Two of these were dual units that switch both positive and negative voltages simultaneously. The RPC's using MOSFET's have slow turnon and turnoff times which limit surge currents and voltage spiking from high di/dt. The GTO's have much faster transition times. All RPC's have programmable overload tripout proportional to I sq T and microsecond tripout for large overloads.

Design of high-voltage, high-power, solid state remote power controllers for aerospace applications

NASA Astrophysics Data System (ADS)

Sturman, J. C.

1985-05-01

Two general types of remote power controllers (RPC's), which combine the functions of a circuit breaker and a switch, were developed for use in dc aerospace systems. Power-switching devices used in the designs are the gate-turnoff thyristor (GTO) and MOSFET. The RPC's can switch dc voltages to 1200 V and currents to 1000 A. Seven different units were constructed and subjected to laboratory and thermal vacuum testing. Two of these were dual units that switch both positive and negative voltages simultaneously. The RPC's using MOSFET's have slow turnon and turnoff times which limit surge currents and voltage spiking from high di/dt. The GTO's have much faster transition times. All RPC's have programmable overload tripout proportional to I sq T and microsecond tripout for large overloads.

Activity Theory as a Theoretical Framework for Health Self-Quantification: A Systematic Review of Empirical Studies.

PubMed

Almalki, Manal; Gray, Kathleen; Martin-Sanchez, Fernando

2016-05-27

Self-quantification (SQ) is a way of working in which, by using tracking tools, people aim to collect, manage, and reflect on personal health data to gain a better understanding of their own body, health behavior, and interaction with the world around them. However, health SQ lacks a formal framework for describing the self-quantifiers' activities and their contextual components or constructs to pursue these health related goals. Establishing such framework is important because it is the first step to operationalize health SQ fully. This may in turn help to achieve the aims of health professionals and researchers who seek to make or study changes in the self-quantifiers' health systematically. The aim of this study was to review studies on health SQ in order to answer the following questions: What are the general features of the work and the particular activities that self-quantifiers perform to achieve their health objectives? What constructs of health SQ have been identified in the scientific literature? How have these studies described such constructs? How would it be possible to model these constructs theoretically to characterize the work of health SQ? A systematic review of peer-reviewed literature was conducted. A total of 26 empirical studies were included. The content of these studies was thematically analyzed using Activity Theory as an organizing framework. The literature provided varying descriptions of health SQ as data-driven and objective-oriented work mediated by SQ tools. From the literature, we identified two types of SQ work: work on data (ie, data management activities) and work with data (ie, health management activities). Using Activity Theory, these activities could be characterized into 6 constructs: users, tracking tools, health objectives, division of work, community or group setting, and SQ plan and rules. We could not find a reference to any single study that accounted for all these activities and constructs of health SQ activity. A Health Self-Quantification Activity Framework is presented, which shows SQ tool use in context, in relation to the goals, plans, and competence of the user. This makes it easier to analyze issues affecting SQ activity, and thereby makes it more feasible to address them. This review makes two significant contributions to research in this field: it explores health SQ work and its constructs thoroughly and it adapts Activity Theory to describe health SQ activity systematically.

Propagation velocities of laser-produced plasmas from copper wire targets and water droplets

NASA Technical Reports Server (NTRS)

Song, Kyo-Dong; Alexander, Dennis R.

1994-01-01

Experiments were performed to determine the plasma propagation velocities resulting from KrF laser irradiation of copper wire target (75 microns diameter) and water droplets (75 microns diameter) at irradiance levels ranging from 25 to 150 GW/sq cm. Plasma propagation velocities were measured using a streak camera system oriented orthogonally to the high-energy laser propagation axis. Plasma velocities were studied as a function of position in the focused beam. Results show that both the shape of the plasma formation and material removal from the copper wire are different and depend on whether the targets are focused or slightly defocused (approximately = 0.5 mm movement in the beam axis). Plasma formation and its position relative to the target is an important factor in determining the practical focal point during high-energy laser interaction with materials. At irradiance of 100 GW/sq cm, the air plasma has two weak-velocity components which propagate toward and away from the incident laser while a strong-velocity component propagates away from the laser beam as a detonation wave. Comparison of the measured breakdown velocities (in the range of 2.22-2.27 x 10(exp 5) m/s) for air and the value calculated by the nonlinear breakdown wave theory at irradiance of 100 GW/sq cm showed a quantitative agreement within approximately 50% while the linear theory and Gaussian pulse theory failed. The detonation wave velocities of plasma generated from water droplets and copper wire targets for different focused cases were measured and analyzed theoretically. The propagation velocities of laser-induced plasma liquid droplets obtained by previous research are compared with current work.

United States Air Force Statistical Digest 1948, Third Annual Edition, Volume 1

DTIC Science & Technology

1948-12-31

L. 1. B. Corporation, Summit, Nn Jersey Lab. For Electronics Inc., Boaton, MasB. Lear Inc., Grand. l:lIlp1ds, Michigan Loach JiBlay CCCPBJl.1, ~1j ADa...l. AlAbama 2. ~ela11iare 2. California 2. Illinois 2. Arkansas J. District of Columbia J. Idaho J. Indiana J. Floriea 4. Ken ~uc1y 4. l!onta.na 4. I""a...bomD, L, Hq. GrouF, ncn, Hq. • • Sroup, Trp Carr. Hq Sq , bOOlb,VHv. Sq, uOOlb, L•••• Sq, Ftr (All 1,ea). sq , Ren, lU~t l’hoto sq, Ken , thoto ••• Sq

Diminiode thermionic conversion with 111-iridium electrodes

NASA Technical Reports Server (NTRS)

Koeger, E. W.; Bair, V. L.; Morris, J. F.

1976-01-01

Preliminary data indicating thermionic-conversion potentialities for a 111-iridium emitter and collector spaced 0.2 mm apart are presented. These results comprise output densities of current and of power as functions of voltage for three sets of emitter, collector, and reservoir temperatures: 1553, 944, 561 K; 1605, 898, 533 K; and 1656, 1028, 586 K. For the 1605 K evaluation, estimates produced work-function values of 2.22 eV for the emitter and 1.63 eV for the collector with a 2.0-eV barrier index (collector work function plus interelectrode voltage drop) corresponding to the maximum output of 5.5 W/sq cm at 0.24 volt. The current, voltage curve for the 1656 K 111-iridium diminiode yields a 6.2 W/sq cm maximum at 0.25 volt and is comparable with the 1700 K envelope for a diode with an etched-rhenium emitter and a 0.025-mm electrode gap made by TECO and evaluated by NASA.

Temperature, illumination and fluence dependence of current and voltage in electron irradiated solar cells

NASA Technical Reports Server (NTRS)

Obenschain, A. F.; Faith, T. J.

1973-01-01

Emperical equations have been derived from measurements of solar cell photovoltaic characteristics relating light generated current, IL, and open circuit voltage, VO, to cell temperature, T, intensity of illumination, W, and 1 Mev electron fluence, phi both 2 ohm-cm and 10 ohm-cm cells were tested. The temperature dependency of IL is similar for both resistivities at 140mw/sq cm; at high temperature the coefficient varies with fluence as phi 0.18, while at low temperatures the coefficient is relatively independent of fluence. Fluence dependent degration causes a decrease in IL at a rate proportional to phi 0.153 for both resistivities. At all intensities other than 560 mw/sq cm, a linear dependence of IL on illumination was found. The temperature coefficient of voltage was, to a good approximation, independent of both temperature and illumination for both resistivities. Illumination dependence of VOC was logarithmic, while the decrease with fluence of VOC varied as phi 0.25 for both resistivities.

Tape casting and partial melting of Bi-2212 thick films

NASA Technical Reports Server (NTRS)

Buhl, D.; Lang, TH.; Heeb, B.; Gauckler, L. J.

1995-01-01

To produce Bi-2212 thick films with high critical current densities tape casting and partial melting is a promising fabrication method. Bi-2212 powder and organic additives were mixed into a slurry and tape casted onto glass by the doctor blade tape casting process. The films were cut from the green tape and partially molten on Ag foils during heat treatment. We obtained almost single-phase and well-textured films over the whole thickness of 20 microns. The orientation of the (a,b)-plane of the grains was parallel to the substrate with a misalignment of less than 6 deg. At 77 K/0T a critical current density of 15, 000 A/sq cm was reached in films of the dimension 1 cm x 2 cm x 20 microns (1 micron V/cm criterion, resistively measured). At 4 K/0T the highest value was 350,000 A/sq cm (1 nV/cm criterion, magnetically measured).

Preparation of thin-film (Ba(0.5),Sr(0.5))TiO3 by the laser ablation technique and electrical properties

NASA Astrophysics Data System (ADS)

Yoon, Soon-Gil; Lee, Jai-Chan; Safari, A.

1994-09-01

The chemical composition and electrical properties were investigated for epitaxially crystallized (Ba(0.5),Sr(0.5))TiO3 (BST) films deposited on Pt/MgO and YBa2Cu3O(7-x) (YBCO)/MgO substrates by the laser ablation technique. Rutherford backscattering spectroscopy analysis shows that thin films on Pt/MgO have almost the same stoichiometric composition as the target material. Films deposited at 600 C exhibited an excellent epitaxial growth, a dielectric constant of 430, and a dissipation factor of 0.02 at 10 kHz frequency. They have a charge storage density of 40 fC/sq micron at an applied electric field of 0.15 MV/cm. Leakage current density of BST thin films on Pt/MgO was smaller than on YBCO/MgO. Their leakage current density is about 0.8 microA/sq cm at an applied electric field of 0.15 MV/cm.

A study on the electrolysis of sulfur dioxide and water for the sulfur cycle hydrogen production process

NASA Technical Reports Server (NTRS)

1980-01-01

Experimental electrolysis cells using various platinum catalyzed carbon electrodes were tested. When operated at 200 mA/sq cm current density using 50 w/o acid at 50 C and 1 atm, a reference cell required 1.22 volts and degraded rapidly. After several improvements were incorporated into electrodes and the test cell configuration, a later cell required only 0.77 volts under identical operating conditions. At a lower current density, 100 mA/sq cm, the cell required only 0.63 volts. Kinetic studies on metal electrodes, measurements of temperature effects on electrode kinetics, investigations of electrocatalytic activities of metal electrodes over a wide range of acid concentrations, cyclic voltametric studies and evaluation of alternate catalysts were also conducted. From diffusivity experiments, a cation exchange membrane material, P-4010, exhibited an excellent diffusion coefficient, more than two orders of magnitude lower than that of rubber. Ionic resistivity measurements of eight materials showed that microporous rubber had the lowest resistivity.

Critical current density and microstructure of screen-printed (Bi,Pb)2Sr2Ca2Cu3O(x) thick film sandwiched between Ag substrates

NASA Astrophysics Data System (ADS)

Oota, A.; Matsui, H.; Funakura, M.; Iwaya, J.; Maeda, J.

1993-07-01

A process of combined rolling and uniaxial pressing with intermediate sintering steps for fabrication of screen-printed (Bi,Pb)2Sr2Ca2Cu3O(x) thick films sandwiched between Ag substrates yields c-axis-oriented microstructures with a high critical current density (Jc) of 1.5 x 10 exp 4 A/sq cm (77 K, 0 T) and 9.0 x 10 exp 4 A/sq cm (23 K, 0 T). The measured Jc anisotropy at 77 K, as a function of the angle Theta between B and c axis, is pronounced. An increase in B sharpens a peak at Theta = 90 deg in the Jc vs Theta curve, together with enhancement of the anisotropy ratio. In high fields above 0.5 T, the half-height angular width of the peak approaches an average misalignment angle between the grains with increasing B.

Progress report on a new search for free e/3 quarks in the cores of 10(15) - 10(16) eV air showers

NASA Technical Reports Server (NTRS)

Hodson, A. L.; Bull, R. M.; Taylor, R. S.; Belford, C. H.

1985-01-01

The Leeds 3 sq m Wilson cloud chamber is being used in a new search for free e/3 quarks close to the axes of 10 to the 15th power - 10 to the 16th power eV air showers. A ratio trigger circuit is used to detect the incidence of air shower cores; the position of the shower center and the axis direction are determined from photographs of current-limited spark chambers. It is thus possible, for the first time, to know where we have looked for quarks in air showers and to select for scanning only those cloud chamber photographs where we have good evidence that the shower axis was close to the chamber. 250 g/sq cm of lead/concrete absorber above the cloud chamber serve to reduce particle densities and make a quark search possible very close to the shower axes. The current status of the search is given.

The CfA Einstein Observatory extended deep X-ray survey

NASA Technical Reports Server (NTRS)

Primini, F. A.; Murray, S. S.; Huchra, J.; Schild, R.; Burg, R.

1991-01-01

All IPC exposures in the Einstein Extended Deep X-ray Survey program have been reanalyzed. The current survey covers about 2.3 sq deg with a typical limiting sensitivity of about 5 x 10 to the -14th ergs/sq cm/s in the energy range from 0.8-3.5 keV. A total of 25 IPC sources are detected above a threshold of 4.5 sigma. A total of 18 are detected independently in the HRI, leading to the identification of six with stars and 11 with extragalactic objects. The remaining sources are classified as extragalactic. The population of identified extragalactic objects is dominated by QSOs, with one or two possible clusters. The basic conclusions of the original survey remain unchanged.

The LDEF ultra heavy cosmic ray experiment

NASA Technical Reports Server (NTRS)

Osullivan, D.; Thompson, A.; Bosch, J.; Keegan, R.; Wenzel, K.-P.; Smit, A.; Domingo, C.

1992-01-01

The LDEF Ultra Heavy Cosmic Ray Experiment (UHCRE) used 16 side viewing LDEF trays giving a total geometry factor for high energy cosmic rays of 30 sq m sr. The total exposure factor was 170 sq m sr y. The experiment is based on a modular array of 192 solid state nuclear track detector stacks, mounted in sets of four in 48 pressure vessels. The extended duration of the LDEF mission has resulted in a greatly enhanced potential scientific yield from the UHCRE. Initial scanning results indicate that at least 1800 cosmic ray nuclei with Z greater than 65 were collected, including the world's first statistically significant sample of actinides. Post flight work to date and the current status of the experiment are reviewed.

Wipe-rinse technique for quantitating microbial contamination on large surfaces

NASA Technical Reports Server (NTRS)

Kirschner, L. E.; Puleo, J. R.

1979-01-01

The evaluation of an improved wipe-rinse technique for the bioassay of large areas was undertaken due to inherent inadequacies in the cotton swab-rinse technique to which assay of spacecraft is currently restricted. Four types of contamination control cloths were initially tested. A polyester-bonded cloth (PBC) was selected for further evaluation because of its superior efficiency and handling characteristics. Results from comparative tests with PBC and cotton swabs on simulated spacecraft surfaces indicated a significantly higher recovery efficiency for the PBC than for the cotton (90.4 versus 75.2%). Of the sampling area sites studied, PBC was found to be most effective on surface areas not exceeding 0.74 sq m (8.0 sq ft).

Subcutaneous Fascial Bands—A Qualitative and Morphometric Analysis

PubMed Central

Li, Weihui; Ahn, Andrew C.

2011-01-01

Background Although fascial bands within the subcutaneous (SQ) layer are commonly seen in ultrasound images, little is known about their functional role, much less their structural characteristics. This study's objective is to describe the morphological features of SQ fascial bands and to systematically evaluate the bands using image analyses tools and morphometric measures. Methods In 28 healthy volunteers, ultrasound images were obtained at three body locations: the lateral aspect of the upper arm, medial aspect of the thigh and posterior aspect of lower leg. Using image analytical techniques, the total SQ band area, fascial band number, fascial band thickness, and SQ zone (layer) thickness were determined. In addition, the SQ spatial coherence was calculated based on the eigenvalues associated with the largest and smallest eigenvectors of the images. Results Fascial bands at these sites were contiguous with the dermis and the epimysium forming an interconnected network within the subcutaneous tissue. Subcutaneous blood vessels were also frequently encased by these fascial bands. The total SQ fascial band area was greater at the thigh and calf compared to the arm and was unrelated to SQ layer (zone) thickness. The thigh was associated with highest average number of fascial bands while calf was associated with the greatest average fascial band thickness. Across body regions, greater SQ zone thickness was associated with thinner fascial bands. SQ coherence was significantly associated with SQ zone thickness and body location (calf with statistically greater coherence compared to arm). Conclusion Fascial bands are structural bridges that mechanically link the skin, subcutaneous layer, and deeper muscle layers. This cohesive network also encases subcutaneous vessels and may indirectly mediate blood flow. The quantity and morphological characteristics of the SQ fascial band may reflect the composite mechanical forces experienced by the body part. PMID:21931632

Entner–Doudoroff pathway for sulfoquinovose degradation in Pseudomonas putida SQ1

PubMed Central

Felux, Ann-Katrin; Spiteller, Dieter; Klebensberger, Janosch; Schleheck, David

2015-01-01

Sulfoquinovose (SQ; 6-deoxy-6-sulfoglucose) is the polar head group of the plant sulfolipid SQ-diacylglycerol, and SQ comprises a major proportion of the organosulfur in nature, where it is degraded by bacteria. A first degradation pathway for SQ has been demonstrated recently, a “sulfoglycolytic” pathway, in addition to the classical glycolytic (Embden–Meyerhof) pathway in Escherichia coli K-12; half of the carbon of SQ is abstracted as dihydroxyacetonephosphate (DHAP) and used for growth, whereas a C3-organosulfonate, 2,3-dihydroxypropane sulfonate (DHPS), is excreted. The environmental isolate Pseudomonas putida SQ1 is also able to use SQ for growth, and excretes a different C3-organosulfonate, 3-sulfolactate (SL). In this study, we revealed the catabolic pathway for SQ in P. putida SQ1 through differential proteomics and transcriptional analyses, by in vitro reconstitution of the complete pathway by five heterologously produced enzymes, and by identification of all four organosulfonate intermediates. The pathway follows a reaction sequence analogous to the Entner–Doudoroff pathway for glucose-6-phosphate: It involves an NAD+-dependent SQ dehydrogenase, 6-deoxy-6-sulfogluconolactone (SGL) lactonase, 6-deoxy-6-sulfogluconate (SG) dehydratase, and 2-keto-3,6-dideoxy-6-sulfogluconate (KDSG) aldolase. The aldolase reaction yields pyruvate, which supports growth of P. putida, and 3-sulfolactaldehyde (SLA), which is oxidized to SL by an NAD(P)+-dependent SLA dehydrogenase. All five enzymes are encoded in a single gene cluster that includes, for example, genes for transport and regulation. Homologous gene clusters were found in genomes of other P. putida strains, in other gamma-Proteobacteria, and in beta- and alpha-Proteobacteria, for example, in genomes of Enterobacteria, Vibrio, and Halomonas species, and in typical soil bacteria, such as Burkholderia, Herbaspirillum, and Rhizobium. PMID:26195800

Contrasting fluvial styles across the mid-Pleistocene climate transition in the northern shelf of the South China Sea: Evidence from 3D seismic data

NASA Astrophysics Data System (ADS)

Zhuo, Haiteng; Wang, Yingmin; Shi, Hesheng; He, Min; Chen, Weitao; Li, Hua; Wang, Ying; Yan, Weiyao

2015-12-01

Multiple successions of buried fluvial channel systems were identified in the Quaternary section of the mid-shelf region of the northern South China Sea, providing a new case study for understanding the interplay between sea level variations and climate change. Using three commercial 3D seismic surveys, accompanied by several 2D lines and a few shallow boreholes, the sequence stratigraphy, seismic geomorphology and stratal architecture of these fluvial channels were carefully investigated. Based on their origin, dimensions, planform geometries and infill architectures, six classes of channel systems, from Class 1 to Class 6, were recognized within five sequences of Quaternary section (SQ1 to SQ5). Three types of fluvial systems among them are incised in their nature, including the trunk incised valleys (Class 1), medium incised valleys (Class 2) and incised tributaries (Class 3). The other three types are unincised, which comprise the trunk channels (Class 4), lateral migrating channels (Class 5) and the stable channels (Class 6). The trunk channels and/or the major valleys that contain braided channels at their base are hypothesized to be a product of deposition from the "big rivers" that have puzzled the sedimentologists for the last decade, providing evidence for the existence of such rivers in the ancient record. Absolute age dates from a few shallow boreholes indicate that the landscapes that were associated with these fluvial systems changed significantly near the completion of the mid-Pleistocene climate transition (MPT), which approximately corresponds to horizon SB2 with an age of ∼0.6 Ma BP. Below SB2, the Early Pleistocene sequence (SQ1) is dominated by a range of different types of unincised fluvial systems. Evidence of incised valleys is absent in SQ1. In contrast, extensive fluvial incision occurred in the successions above horizon SB2 (within SQ2-SQ5). Although recent studies call for increased incision being a product of climate-controlled increase in river discharge, the down-dip location of our study area suggests that relative sea level change was the most important control of the evolution of fluvial systems. However, it is acknowledged that climate change was also important through its role in regulating glacio-eustasy. We speculate that the small amplitude and periodicity of sea level cycles before and during the MPT were not sufficient to fully expose the shelf and cause extensive fluvial incisions. Completion of the MPT as well as the onset of 100 ky climate cycles at ∼0.6 Ma, during which the duration of cycles and magnitude of sea level change both increased, are considered to be triggering event for extensive development of incised fluvial systems. In addition to the eustatically driven causes of enhanced incision, the intensification of the East Asia monsoon at 0.9 Ma and 0.6 Ma driven by the episodic uplift of the Tibetan Plateau may have also significantly enhanced the amplitude of sea level falls and thus the fluvial incisions of the northern shelf of the South China Sea.

Sleep quality and risk factors of atherosclerosis in predialysis chronic kidney disease.

PubMed

Guney, Ibrahim; Akgul, Yavuz S S; Gencer, Vedat; Aydemir, Harun; Aslan, Uysaler; Ecirli, Samil

2017-01-13

Chronic kidney disease (CKD) patients have more frequent sleep disorders and cardiovascular disease than normals. Since arterial stiffness as a risk factor of atherosclerosis can be evaluated with pulse wave velocity (PWV), we aimed to investigate the prevalance of sleep quality (SQ) and the relationship between SQ and risk factors of atherosclerosis and whether there is a relationship between SQ and PWV (the indicator of arterial stiffness) in predialysis CKD patients. This cross-sectional study was carried out in CKD patients followed at the Nephrology Department in Konya, Turkey, between November 2014 and March 2015. A total of 484 CKD patients were screened. Of the 484 patients, 285 patients were excluded. The remaining 199 CKD patients without cardiovascular disease at stage 3, 4, and 5 (predialysis) were included in the final study. The SQ of the patients was evaluated by the Pittsburgh Sleep Quality Index (PSQI). PWV was measured by using a single-cuff arteriography device (Mobil-O-Graph PWA, a model pulse wave analysis device; IEM). A total of 199 predialysis CKD patients were included in the study, 73 of whom (36.7 %) were 'poor sleepers' (global PSQI >5). Patients with poor SQ were older than those with good SQ (p = 0.077). SQ was worse in female patients compered to male patients (p = 0.001). SQ was worse in obese patients. As laboratory parameters, serum phosphorus, LDL cholesterol, and triglycerides levels correlated positively with SQ (respectively; r = 0.245, p&0.001; r = 0.142, p = 0.049; r = 0.142, p = 0.048). The indicator of arterial stiffness, PWV, was higher in patients with poor SQ (p = 0.033). Hyperphosphatemia and female gender are determined as risk factors for poor SQ in multivariate analysis (p = 0.049, ExpB = 1.477; p = 0.009, ExpB = 0,429, respectively). Our study showed for the first time that there is a relationship between SQ and risk factors of atherosclerosis in predialysis CKD patients.

Performance evaluation of the Solar Building Test Facility

NASA Technical Reports Server (NTRS)

Jensen, R. N.

1981-01-01

The general performance of the NASA Solar Building Test Facility (SBTF) and its subsystems and components over a four year operational period is discussed, and data are provided for a typical one year period. The facility consists of a 4645 sq office building modified to accept solar heated water for operation of an absorption air conditioner and a baseboard heating system. An adjoining 1176 sq solar flat plate collector field with a 114 cu tank provides the solar heated water. The solar system provided 57 percent of the energy required for heating and cooling on an annual basis. The average efficiency of the solar collectors was 26 percent over a one year period.

Activity Theory as a Theoretical Framework for Health Self-Quantification: A Systematic Review of Empirical Studies

PubMed Central

2016-01-01

Background Self-quantification (SQ) is a way of working in which, by using tracking tools, people aim to collect, manage, and reflect on personal health data to gain a better understanding of their own body, health behavior, and interaction with the world around them. However, health SQ lacks a formal framework for describing the self-quantifiers’ activities and their contextual components or constructs to pursue these health related goals. Establishing such framework is important because it is the first step to operationalize health SQ fully. This may in turn help to achieve the aims of health professionals and researchers who seek to make or study changes in the self-quantifiers’ health systematically. Objective The aim of this study was to review studies on health SQ in order to answer the following questions: What are the general features of the work and the particular activities that self-quantifiers perform to achieve their health objectives? What constructs of health SQ have been identified in the scientific literature? How have these studies described such constructs? How would it be possible to model these constructs theoretically to characterize the work of health SQ? Methods A systematic review of peer-reviewed literature was conducted. A total of 26 empirical studies were included. The content of these studies was thematically analyzed using Activity Theory as an organizing framework. Results The literature provided varying descriptions of health SQ as data-driven and objective-oriented work mediated by SQ tools. From the literature, we identified two types of SQ work: work on data (ie, data management activities) and work with data (ie, health management activities). Using Activity Theory, these activities could be characterized into 6 constructs: users, tracking tools, health objectives, division of work, community or group setting, and SQ plan and rules. We could not find a reference to any single study that accounted for all these activities and constructs of health SQ activity. Conclusions A Health Self-Quantification Activity Framework is presented, which shows SQ tool use in context, in relation to the goals, plans, and competence of the user. This makes it easier to analyze issues affecting SQ activity, and thereby makes it more feasible to address them. This review makes two significant contributions to research in this field: it explores health SQ work and its constructs thoroughly and it adapts Activity Theory to describe health SQ activity systematically. PMID:27234343

Recent advances in solid polymer electrolyte fuel cell technology with low platinum loading electrodes

NASA Technical Reports Server (NTRS)

Srinivasan, Supramaniam; Manko, David J.; Koch, Hermann; Enayetullah, Mohammad A.; Appleby, A. John

1989-01-01

Of all the fuel cell systems only alkaline and solid polymer electrolyte fuel cells are capable of achieving high power densities (greater than 1 W/sq cm) required for terrestrial and extraterrestrial applications. Electrode kinetic criteria for attaining such high power densities are discussed. Attainment of high power densities in solid polymer electrolyte fuel cells has been demonstrated earlier by different groups using high platinum loading electrodes (4 mg/sq cm). Recent works at Los Alamos National Laboratory and at Texas A and M University (TAMU) demonstrated similar performance for solid polymer electrolyte fuel cells with ten times lower platinum loading (0.45 mg/sq cm) in the electrodes. Some of the results obtained are discussed in terms of the effects of type and thickness of membrane and of the methods platinum localization in the electrodes on the performance of a single cell.

Improving the Charge Carrier Transport and Suppressing Recombination of Soluble Squaraine-Based Solar Cells via Parallel-Like Structure

PubMed Central

Zhu, Youqin; Liu, Jingli; Zhao, Jiao; Li, Yang; Qiao, Bo; Song, Dandan; Huang, Yan; Xu, Zheng; Zhao, Suling; Xu, Xurong

2018-01-01

Small molecule organic solar cells (SMOSCs) have attracted extensive attention in recent years. Squaraine (SQ) is a kind of small molecule material for potential use in high-efficiency devices, because of its high extinction coefficient and low-cost synthesis. However, the charge carrier mobility of SQ-based film is much lower than other effective materials, which leads to the pretty low fill factor (FF). In this study, we improve the performance of SQ derivative-based solar cells by incorporating PCDTBT into LQ-51/PC71BM host binary blend film. The incorporation of PCDTBT can not only increase the photon harvesting, but also provide an additional hole transport pathway. Through the charge carrier mobility and transient photovoltage measurement, we find that the hole mobility and charge carrier lifetime increase in the ternary system. Also, we carefully demonstrate that the charge carrier transport follows a parallel-like behavior. PMID:29747394

Classification of Small Negative Lightning Reports at the KSC-ER

NASA Technical Reports Server (NTRS)

Ward, Jennifer G.; Cummins, Kenneth L.; Krider, Philip

2008-01-01

The NASA Kennedy Space Center (KSC) and Air Force Eastern Range (ER) operate an extensive suite of lightning sensors because Florida experiences the highest area density of ground strikes in the United States, with area densities approaching 16 fl/sq km/yr when accumulated in 10x10 km (100 sq km) grids. The KSC-ER use data derived from two cloud-to-ground (CG) lightning detection networks, the "Cloud-to-Ground Lightning Surveillance System" (CGLSS) and the U.S. National Lightning Detection Network (TradeMark) (NLDN) plus a 3-dimensional lightning mapping system, the Lightning Detection and Ranging (LDAR) system, to provide warnings for ground operations and to insure mission safety during space launches. For operational applications at the KSC-ER it is important to understand the performance of each lightning detection system in considerable detail. In this work we examine a specific subset of the CGLSS stroke reports that have low values of the negative inferred peak current, Ip, i.e. values between 0 and -7 kA, and were thought to produce a new ground contact (NGC). When possible, the NLDN and LDAR systems were used to validate the CGLSS classification and to determine how many of these reported strokes were first strokes, subsequent strokes in a pre-existing channel (PEC), or cloud pulses that the CGLSS misclassified as CG strokes. It is scientifically important to determine the smallest current that can reach the ground either in the form of a first stroke or by way of a subsequent stroke that creates a new ground contact. In Biagi et al (2007), 52 low amplitude, negative return strokes ([Ip] < or = 10 kA) were evaluated in southern Arizona, northern Texas, and southern Oklahoma. The authors found that 50-87% of the small NLDN reports could be classified as CG (either first or subsequent strokes) on the basis of video and waveform recordings. Low amplitude return strokes are interesting because they are usually difficult to detect, and they are thought to bypass conventional lightning protection that relies on a sufficient attractive radius to prevent "shielding failure" (Golde, 1977). They also have larger location errors compared to the larger current events. In this study, we use the estimated peak current provided by the CGLSS and the results of our classification to determine the minimum Ip for each category of CG stroke and its probability of occurrence. Where possible, these results are compared to the findings in the literature.

Malfunction Investigation of the XM935 Point Detonating Fuze

DTIC Science & Technology

1977-04-01

1 PSK* UNCHANGED FUMLY AR! 2 PSM UNCHANGED FULLY ARMED 3 OK PS4 UNCHANGD 4 CK P24 UNC DNGED 5 PSK (more than S.Q. Det Edge Visible FuLLY AP1M other...Continued) F= NO. DRC NO. 1 2 3 4 5 6 7 8 9 10 3 PSK UNCH UNCH UNCE SEE SQ UNCH UNCH UNCH UNCH UN1H 4 PS4 UNCH SKH E SQ UNCH tNCH UNCH UNCH U2 L!CH...EDGE 5 PS UNCH tCH SE SQ UNCH MMH UNCH UNCH UWCH WECH 6 P4M UNCH UNCH Q SEE SQ EDGE 7 PSK UNCH UNCH SEE SO WXC EDGE a P UNCP L4 UNCH SC E SQ 9 PS4 UNCX

Adsorption of Halogenated Fire-Extinguishing Agents on Powders

NASA Technical Reports Server (NTRS)

Barduhn, Allen J.; Patel, Bhailal S.; Meyer, Walter; Smura, Bronislaw B.

1960-01-01

The amounts of four different Freons adsorbed by carbon, silica gel, alumina, and molecular sieves were determined at pressures up to 225 lb/sq in. The carbon adsorbed 50 to 100 percent and the silica gels, 30 to 50 percent of their own weight of Freon. Several adsorbed systems were tested in a standard dry-powder extinguisher on a 5-sq-ft gasoline fire for their effectiveness in putting out a fire. One of the Freons (bromotrifluoromethane) and carbon extinguished fires about as well as bicarbonate powder and nitrogen.

High flux heat exchanger

NASA Astrophysics Data System (ADS)

Flynn, Edward M.; Mackowski, Michael J.

1993-01-01

This interim report documents the results of the first two phases of a four-phase program to develop a high flux heat exchanger for cooling future high performance aircraft electronics. Phase 1 defines future needs for high flux heat removal in advanced military electronics systems. The results are sorted by broad application categories: (1) commercial digital systems, (2) military data processors, (3) power processors, and (4) radar and optical systems. For applications expected to be fielded in five to ten years, the outlook is for steady state flux levels of 30-50 W/sq cm for digital processors and several hundred W/sq cm for power control applications. In Phase 1, a trade study was conducted on emerging cooling technologies which could remove a steady state chip heat flux of 100 W/sq cm while holding chip junction temperature to 90 C. Constraints imposed on heat exchanger design, in order to reflect operation in a fighter aircraft environment, included a practical lower limit on coolant supply temperature, the preference for a nontoxic, nonflammable, and nonfreezing coolant, the need to minimize weight and volume, and operation in an accelerating environment. The trade study recommended the Compact High Intensity Cooler (CHIC) for design, fabrication, and test in the final two phases of this program.

77 FR 14411 - Federal Property Suitable as Facilities To Assist the Homeless

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-09

... Energy, Office of Engineering & Construction Management, MA-50, 1000 Independence Ave. SW., Washington... Landholding Agency: Air Force Property Number: 18201210016 Status: Underutilized Directions: 1076 Jack's...: 1077 Jack's Valley Rd. Comments: 512 sq. ft.; current use: vacant; bldg. has no heat Kitchen Center...

Comparison of Subcutaneous Regular Insulin and Lispro Insulin in Diabetics Receiving Continuous Nutrition

PubMed Central

Stull, Mamie C.; Strilka, Richard J.; Clemens, Michael S.; Armen, Scott B.

2015-01-01

Background: Optimal management of non–critically ill patients with diabetes maintained on continuous enteral feeding (CEN) is poorly defined. Subcutaneous (SQ) lispro and SQ regular insulin were compared in a simulated type 1 and type 2 diabetic patient receiving CEN. Method: A glucose-insulin feedback mathematical model was employed to simulate type 1 and type 2 diabetic patients on CEN. Each patient received 25 SQ injections of regular insulin or insulin lispro, ranging from 0-6 U. Primary endpoints were the change in mean glucose concentration (MGC) and change in glucose variability (GV); hypoglycemic episodes were also reported. The model was first validated against patient data. Results: Both SQ insulin preparations linearly decreased MGC, however, SQ regular insulin decreased GV whereas SQ lispro tended to increase GV. Hourly glucose concentration measurements were needed to capture the increase in GV. In the type 2 diabetic patient, “rebound hyperglycemia” occurred after SQ lispro was rapidly metabolized. Although neither SQ insulin preparation caused hypoglycemia, SQ lispro significantly lowered MGC compared to SQ regular insulin. Thus, it may be more likely to cause hypoglycemia. Analyses of the detailed glucose concentration versus time data suggest that the inferior performance of lispro resulted from its shorter duration of action. Finally, the effects of both insulin preparations persisted beyond their duration of actions in the type 2 diabetic patient. Conclusions: Subcutaneous regular insulin may be the short-acting insulin preparation of choice for this subset of diabetic patients. Clinical trial is required before a definitive recommendation can be made. PMID:26134836

Comparison of Subcutaneous Regular Insulin and Lispro Insulin in Diabetics Receiving Continuous Nutrition: A Numerical Study.

PubMed

Stull, Mamie C; Strilka, Richard J; Clemens, Michael S; Armen, Scott B

2015-06-30

Optimal management of non-critically ill patients with diabetes maintained on continuous enteral feeding (CEN) is poorly defined. Subcutaneous (SQ) lispro and SQ regular insulin were compared in a simulated type 1 and type 2 diabetic patient receiving CEN. A glucose-insulin feedback mathematical model was employed to simulate type 1 and type 2 diabetic patients on CEN. Each patient received 25 SQ injections of regular insulin or insulin lispro, ranging from 0-6 U. Primary endpoints were the change in mean glucose concentration (MGC) and change in glucose variability (GV); hypoglycemic episodes were also reported. The model was first validated against patient data. Both SQ insulin preparations linearly decreased MGC, however, SQ regular insulin decreased GV whereas SQ lispro tended to increase GV. Hourly glucose concentration measurements were needed to capture the increase in GV. In the type 2 diabetic patient, "rebound hyperglycemia" occurred after SQ lispro was rapidly metabolized. Although neither SQ insulin preparation caused hypoglycemia, SQ lispro significantly lowered MGC compared to SQ regular insulin. Thus, it may be more likely to cause hypoglycemia. Analyses of the detailed glucose concentration versus time data suggest that the inferior performance of lispro resulted from its shorter duration of action. Finally, the effects of both insulin preparations persisted beyond their duration of actions in the type 2 diabetic patient. Subcutaneous regular insulin may be the short-acting insulin preparation of choice for this subset of diabetic patients. Clinical trial is required before a definitive recommendation can be made. © 2015 Diabetes Technology Society.

E-Service Quality, E-Satisfaction and E-Loyalty of Online Shoppers in Business to Consumer Market; Evidence form Malaysia

NASA Astrophysics Data System (ADS)

Ting, Ong Soo; Ariff, Mohd Shoki Md; Zakuan, Norhayati; Sulaiman, Zuraidah; Zameri Mat Saman, Muhamad

2016-05-01

The growing usage of internet and online shopping in Malaysia presents a huge prospect in e-commerce market, specifically for B2C segment. As a result, electronic service quality (e-SQ), electronic satisfaction (e-Satisfaction) and electronic loyalty (e-Loyalty) become vital for online retailers to attract and retain online shoppers in this virtual environment. The association between e-SQ, e-Satisfaction and e-Loyalty should be continuously examined to cope with the advancement in information and communication technology, and the changing expectation of online shoppers. However, construct of e-SQ for online retailers in B2C market is still debatable. In this research, E-SERVQUAL was integrated with the other e-SQ scales to measure e-SQ of a prominent online retailer in Malaysia. Specifically, the e-SQ constructs are Efficiency, Privacy and Trust, Fulfilment, Responsiveness, Contact and Website Design. 390 sets of completed and usable questionnaires were gathered using online questionnaire and convenience sampling procedure. The result indicated that the five proposed dimensions of e-SQ constitute e-SQ of online retailer in B2C market. All the dimensions of e-SQ were found to have positive and significant effect on e-Satisfaction of online shoppers. Responsiveness of e-SQ had the strongest impact on e-satisfaction of online shoppers. The shoppers e-Satisfaction was positively and significantly affected their e-Loyalty towards continuous usage of online retailer's website. Managerial and theoretical implications are discussed based on the results of the study.

Anomalous Variability in Antarctic Sea Ice Extents During the 1960s With the Use of Nimbus Data

NASA Technical Reports Server (NTRS)

Gallaher, David W.; Campbell, G. Garrett; Meier, Walter N.

2013-01-01

The Nimbus I, II, and III satellites provide a new opportunity for climate studies in the 1960s. The rescue of the visible and infrared imager data resulted in the utilization of the early Nimbus data to determine sea ice extent. A qualitative analysis of the early NASA Nimbus missions has revealed Antarctic sea ice extents that are significant larger and smaller than the historic 1979-2012 passive microwave record. The September 1964 ice mean area is 19.7x10(exp 6) sq. km +/- 0.3x10(exp 6) sq. km. This is more the 250,000 sq. km greater than the 19.44x10(exp 6) sq. km seen in the new 2012 historic maximum. However, in August 1966 the maximum sea ice extent fell to 15.9x10(exp 6) sq. km +/- 0.3x10(exp 6) sq. km. This is more than 1.5x10(exp 6) sq. km below the passive microwave record of 17.5x10(exp 6) sq. km set in September of 1986. This variation between 1964 and 1966 represents a change of maximum sea ice of over 3x10(exp 6) sq. km in just two years. These inter-annual variations while large, are small when compared to the Antarctic seasonal cycle.

Preliminary operational results from the Willard solar power system

NASA Technical Reports Server (NTRS)

Fenton, D. L.; Abernathy, G. H.; Krivokapich, G.; Ellibee, D. E.; Chilton, V.

1980-01-01

The solar powered system located near Willard, New Mexico, generates mechanical or electrical power at a capacity of 19 kW (25 HP). The solar collection system incorporates east/west tracking parabolic trough collectors with a total aperture area of 1275 sq m (13,720 sq ft). The hot oil type thermal energy storage is sufficient for approximately 20 hours of power system operation. The system utilizes a reaction type turbine in conjunction with an organic Rankine cycle engine. Total collector field efficiency reaches a maximum of 20 percent near the winter solstice and about 50 percent during the summer. During the month of July, 1979, the system pumped 60 percent of the 35,300 cu m (28.6 acre-feet) of water delivered. Operating efficiencies for the turbine component, organic Rankine cycle engine and the complete power system are respectively 65 to 75 percent, 12 to 15 percent and 5 to 6 percent. Significant maintenance time was expended on both the collector and power systems throughout the operational period.

Preliminary operational results from the Willard solar power system

NASA Astrophysics Data System (ADS)

Fenton, D. L.; Abernathy, G. H.; Krivokapich, G.; Ellibee, D. E.; Chilton, V.

1980-05-01

The solar powered system located near Willard, New Mexico, generates mechanical or electrical power at a capacity of 19 kW (25 HP). The solar collection system incorporates east/west tracking parabolic trough collectors with a total aperture area of 1275 sq m (13,720 sq ft). The hot oil type thermal energy storage is sufficient for approximately 20 hours of power system operation. The system utilizes a reaction type turbine in conjunction with an organic Rankine cycle engine. Total collector field efficiency reaches a maximum of 20 percent near the winter solstice and about 50 percent during the summer. During the month of July, 1979, the system pumped 60 percent of the 35,300 cu m (28.6 acre-feet) of water delivered. Operating efficiencies for the turbine component, organic Rankine cycle engine and the complete power system are respectively 65 to 75 percent, 12 to 15 percent and 5 to 6 percent. Significant maintenance time was expended on both the collector and power systems throughout the operational period.

AN OPPORTUNISTIC SEARCH FOR EXTRATERRESTRIAL INTELLIGENCE (SETI) WITH THE MURCHISON WIDEFIELD ARRAY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tingay, S. J.; Tremblay, C.; Walsh, A.

A spectral line image cube generated from 115 minutes of MWA data that covers a field of view of 400 sq, deg. around the Galactic Center is used to perform the first Search for ExtraTerrestrial Intelligence (SETI) with the Murchison Widefield Array (MWA). Our work constitutes the first modern SETI experiment at low radio frequencies, here between 103 and 133 MHz, paving the way for large-scale searches with the MWA and, in the future, the low-frequency Square Kilometre Array. Limits of a few hundred mJy beam{sup −1} for narrowband emission (10 kHz) are derived from our data, across our 400more » sq. deg. field of view. Within this field, 45 exoplanets in 38 planetary systems are known. We extract spectra at the locations of these systems from our image cube to place limits on the presence of narrow line emission from these systems. We then derive minimum isotropic transmitter powers for these exoplanets; a small handful of the closest objects (10 s of pc) yield our best limits of order 10{sup 14} W (Equivalent Isotropic Radiated Power). These limits lie above the highest power directional transmitters near these frequencies currently operational on Earth. A SETI experiment with the MWA covering the full accessible sky and its full frequency range would require approximately one month of observing time. The MWA frequency range, its southern hemisphere location on an extraordinarily radio quiet site, its very large field of view, and its high sensitivity make it a unique facility for SETI.« less

Tropical Deforestation in the Bolivian Amazon

NASA Technical Reports Server (NTRS)

Tucker, Compton J.; Steininger, Marc K.; Townshend, John R. G.; Killeen, Timothy R.; Desch, Arthur

2000-01-01

Landsat satellite images from the mid-1980s and early 1990s were used to map tropical forest extent and deforestation in approximately 800,000 sq km of Amazonian Bolivia. Forest cover extent, including tropical deciduous forest, totalled 472,000 sq km while the area of natural non-forest formations totalled 298,000 sq km. The area deforested totalled 15,000 sq km in the middle 1980s and 28,800 sq km by the early 1990s. The rate of tropical deforestation in the >1,000 mm/y precipitation forest zone of Bolivia was 2,200 sq km/y from 1985-1986 to 1992-1994. We document a spatially-concentrated "deforestation zone" in Santa Cruz Department where >60% of the Bolivian deforestation is occurring at an accelerating rate in areas of tropical deciduous dry forest.

Correlation between developmental quotients (DASII) and social quotient (Malin's VSMS) in Indian children aged 6 months to 2 years.

PubMed

Bhave, Anupama; Bhargava, Roli; Kumar, Rashmi

2011-03-01

To determine correlation between developmental quotients (DQ) (DASII) and social quotients (SQ) (Malin's Vineland Social Maturity Scale (VSMS)). Malin's VSMS and DASII were done in 135 children aged 6 months to 2 years. SQ and DQ motor and mental were correlated using Pearson's correlation coefficient (r). Mean SQ and DQ and age equivalent scores were compared. Correlation coefficients between SQ and DQ (mental and motor were 0.849 and 0.791, respectively. Social age correlated highly with mental age (r = 0.906). Mean SQ was higher than mean DQa. SQ tends to be higher than DQ and correlates best with DQ mental. © 2010 The Authors. Journal of Paediatrics and Child Health © 2010 Paediatrics and Child Health Division (Royal Australasian College of Physicians).

Electric current in a unipolar sunspot with an untwisted field

NASA Technical Reports Server (NTRS)

Osherovich, V. A.; Garcia, H. A.

1990-01-01

The return flux (RF) sunspot model is applied to a round, unipolar sunspot observed by H. Kawakami (1983). Solving the magnetohydrostatic problem using the gas pressure deficit between the umbral and quiet-sun atmospheres as a source function, a distribution of electric current density in an untwisted, unipolar sunspot as a function of height and radial distance from the sunspot center is observed. Maximum electric current density is about 32 mA/sq m at the bottom of the sunspot.

DynaGuard: Armoring Canary-Based Protections against Brute-Force Attacks

DTIC Science & Technology

2015-12-11

public domain. Non-exclusive copying or redistribution is...sje ng 462 .lib qua ntu m 464 .h2 64r ef 471 .om net pp 473 .as tar 483 .xa lan cbm k Apa che Ng inx Pos tgre SQ L SQ Lite My SQ L Sl ow do w n (n...k 456 .hm me r 458 .sje ng 462 .lib qua ntu m 464 .h2 64r ef 471 .om net pp 473 .as tar 483 .xa lan cbm k Apa che Ng inx Pos tgre SQ L SQ Lite My

Creativity measured by divergent thinking is associated with two axes of autistic characteristics

PubMed Central

Takeuchi, Hikaru; Taki, Yasuyuki; Sekiguchi, Atsushi; Nouchi, Rui; Kotozaki, Yuka; Nakagawa, Seishu; Miyauchi, Carlos M.; Iizuka, Kunio; Yokoyama, Ryoichi; Shinada, Takamitsu; Yamamoto, Yuki; Hanawa, Sugiko; Araki, Tsuyoshi; Hashizume, Hiroshi

2014-01-01

Creativity generally involves the conception of original and valuable ideas, and it plays a key role in scientific achievement. Moreover, individuals with autistic spectrum conditions (ASCs) tend to achieve in scientific fields. Recently, it has been proposed that low empathizing and high systemizing characterize individuals with ASCs. Empathizing is the drive to identify the mental status of other individuals and respond to it with an appropriate emotion; systemizing is the drive to analyze a system. It has been proposed that this higher systemizing underlies the scientific achievement of individuals with ASCs, suggesting the possible positive association between creativity and systemizing. However, previous findings on the association between ASCs and creativity were conflicting. Conversely, previous studies have suggested an association between prosocial traits and creativity, indicating the possible association between empathizing and creativity. Here we investigated the association between creativity measured by divergent thinking (CDT) and empathizing, systemizing, and the discrepancy between systemizing and empathizing, which is called D score. CDT was measured using the S-A creativity test. The individual degree of empathizing (empathizing quotient, EQ) and that of systemizing (systemizing quotient, SQ), and D score was measured via a validated questionnaire (SQ and EQ questionnaires). The results showed that higher CDT was significantly and positively correlated with both the score of EQ and the score of SQ but not with D score. These results suggest that CDT is positively associated with one of the characteristics of ASCs (analytical aspects), while exhibiting a negative association with another (lower social aspects). Therefore, the discrepancy between systemizing and empathizing, which is strongly associated with autistic tendency, was not associated with CDT. PMID:25191299

78 FR 53821 - Federal Property Suitable as Facilities To Assist the Homeless

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-30

...: Excess Comments: Off-site removal only; 8,736 sq. ft.; current use: Administrative office; fair....; Admin. 3 mons. vacant; fair conditions; w/in secured area; contact Army for accessibility/ removal reqs... Number: 21201310012 Status: Excess Comments: Off-site removal only; 2,100 sf.; Admin.; fair conditions; w...

76 FR 80378 - Federal Property Suitable as Facilities To Assist the Homeless

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-23

... sq. ft.; current use: explosive testing; needs extensive repairs; possible asbestos and lead base... asbestos and mold Bldg. 1197 Ft. Knox Ft. Knox KY 40121 Landholding Agency: Army Property Number... lead base paint, asbestos, and mold Rhode Island FDA Davisville Site 113 Bruce Boyer Street North...

76 FR 65520 - Federal Property Suitable as Facilities To Assist the Homeless

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-21

...: Excess GSA Number: 1-X-MI-664B Comments: 89 sq. ft; current use: storage; non-friable asbestos and lead... Comments: both properties has asbestos present Reasons: Contamination Bldgs. 0004-0203 Dam Camp Storage...: 61201140006 Status: Unutilized Comments: Asbestos present Reasons: Floodway, Contamination, Extensive...

Soil quality evaluation using Soil Management Assessment Framework (SMAF) in Brazilian oxisols with contrasting texture

USDA-ARS?s Scientific Manuscript database

To ensure current land use strategies and management practices are economically, environmentally, and socially sustainable, tools and techniques for assessing and quantifying changes in soil quality/health (SQ) need to be developed through rigorous research and potential use by consultants, and othe...

78 FR 51141 - Submission for OMB Review; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-20

... business surveys. The BR is used to identify the set of statistical units that represents an economic data....S. Census Bureau. Title: Business and Professional Classification Report. Form Number(s): SQ-CLASS... Uses: The Economic Census and current business surveys represent the primary source of facts about the...

Solar heating and hot water system installed at Saint Louis, Missouri

NASA Technical Reports Server (NTRS)

1980-01-01

The solar heating and hot water system installed at the William Tao & Associates, Inc., office building in St. Louis, Missouri is described, including maintenance and construction problems, final drawings, system requirements, and manufacturer's component data. The solar system was designed to provide 50 percent of the hot water requirements and 45 percent of the space heating needs for a 900 sq ft office space and drafting room. The solar facility has 252 sq ft of glass tube concentrator collectors and a 1000 gallon steel storage tank buried below a concrete slab floor. Freeze protection is provided by a propylene glycol/water mixture in the collector loop. The collectors are roof mounted on a variable tilt array which is adjusted seasonally and is connected to the solar thermal storage tank by a tube-in-shell heat exchanger. Incoming city water is preheated through the solar energy thermal storage tank.

Flight test of carbon-phenolic on a spacecraft launched by the pacemaker vehicle system

NASA Technical Reports Server (NTRS)

Walton, T. E., Jr.; Witte, W. G.

1972-01-01

Carbon-phenolic material consisting of 50 percent carbon fibers and 50 percent phenolic resin was flight tested on a recoverable spacecraft launched by the Pacemaker vehicle system. The heat shield of the spacecraft was fabricated so that the carbon fibers in the ablator material had different orientations over several areas of the spacecraft. The environment in which the spacecraft was tested produced heating rates on the hemispherical nose up to 13.6 MW/sq m (1200 Btu/sq ft/sec) and stagnation-point pressures up to 1.27 MN/sq m (12.5 atm). The experimental results are presented. Due to high heating rates and possible spallation and mechanical char removal the greatest mass loss occurred in the nose region. Essentially uniform surface recession and char thickness were observed on the conical section of the spacecraft. A comparison of measured heating rates with computed turbulent and laminar heating rates, as well as measurements of sound-pressure fluctuations in the boundary layer obtained with acoustic sensors, indicated that the boundary layer underwent transition. The acoustic sensor provides an interesting new data form for the general study of boundary-layer transition for free-flight investigations.

Wrapped Multilayer Insulation

NASA Technical Reports Server (NTRS)

Dye, Scott A.

2015-01-01

New NASA vehicles, such as Earth Departure Stage (EDS), Orion, landers, and orbiting fuel depots, need improved cryogenic propellant transfer and storage for long-duration missions. Current cryogen feed line multilayer insulation (MLI) performance is 10 times worse per area than tank MLI insulation. During each launch, cryogenic piping loses approximately 150,000 gallons (equivalent to $300,000) in boil-off during transfer, chill down, and ground hold. Quest Product Development Corp., teaming with Ball Aerospace, developed an innovative advanced insulation system, Wrapped MLI (wMLI), to provide improved thermal insulation for cryogenic feed lines. wMLI is high-performance multilayer insulation designed for cryogenic piping. It uses Quest's innovative discrete-spacer technology to control layer spacing/ density and reduce heat leak. The Phase I project successfully designed, built, and tested a wMLI prototype with a measured heat leak 3.6X lower than spiral-wrapped conventional MLI widely used for piping insulation. A wMLI prototype had a heat leak of 7.3 W/sq m, or 27 percent of the heat leak of conventional MLI (26.7 W/sq m). The Phase II project is further developing wMLI technology with custom, molded polymer spacers and advancing the product toward commercialization via a rigorous testing program, including developing advanced vacuuminsulated pipe for ground support equipment.

Solar Power System Analyses for Electric Propulsion Missions

NASA Technical Reports Server (NTRS)

Kerslake, Thomas W.; Gefert, Leon P.

1999-01-01

Solar electric propulsion (SEP) mission architectures are applicable to a wide range of NASA missions including human Mars exploration and robotic exploration of the outer planets. In this paper, we discuss the conceptual design and detailed performance analysis of an SEP stage electric power system (EPS). EPS performance, mass and area predictions are compared for several PV array technologies. Based on these studies, an EPS design for a 1-MW class, Human Mars Mission SEP stage was developed with a reasonable mass, 9.4 metric tons, and feasible deployed array area, 5800 sq m. An EPS was also designed for the Europa Mapper spacecraft and had a mass of 151 kg and a deployed array area of 106 sq m.

A dc-coupled, high sensitivity bolometric detector system for the Infrared Telescope in Space

NASA Technical Reports Server (NTRS)

Devlin, M.; Lange, A. E.; Wilbanks, T.; Sato, S.

1993-01-01

We report the performance of an ac bridge readout system that has been developed for use on the Infrared Telescope in Space which is scheduled for launch in 1994. The ac bridge readout provides excellent dc stability enabling observing strategies well-suited to space-borne observations. The ability to modulate the optical signal slowly allows the use of new, highly sensitive, long time-constant bolometers. At 300 mK, the bolometers have an electrical noise equivalent power of 3 x 10 exp -17 W/sq rt Hz. The total noise of the differential signal, including amplifier noise, is less than 8 x 10 exp -17 W/sq rt Hz at frequencies as low as 35 mHz.

On the effectiveness of recession analysis methods for capturing the characteristic storage-discharge relation: An intercomparison study

NASA Astrophysics Data System (ADS)

Chen, X.; Kumar, M.; Basso, S.; Marani, M.

2017-12-01

Storage-discharge (S-Q) relations are widely used to derive watershed properties and predict streamflow responses. These relations are often obtained using different recession analysis methods, which vary in recession period identification criteria and Q vs. -dQ/dt fitting scheme. Although previous studies have indicated that different recession analysis methods can result in significantly different S-Q relations and subsequently derived hydrological variables, this observation has often been overlooked and S-Q relations have been used in as is form. This study evaluated the effectiveness of four recession analysis methods in obtaining the characteristic S-Q relation and reconstructing the streamflow. Results indicate that while some methods generally performed better than others, none of them consistently outperformed the others. Even the best-performing method could not yield accurate reconstructed streamflow time series and its PDFs in some watersheds, implying that either derived S-Q relations might not be reliable or S-Q relations cannot be used for hydrological simulations. Notably, accuracy of the methods is influenced by the extent of scatter in the ln(-dQ/dt) vs. ln(Q) plot. In addition, the derived S-Q relation was very sensitive to the criteria used for identifying recession periods. This result raises a warning sign against indiscriminate application of recession analysis methods and derived S-Q relations for watershed characterizations or hydrologic simulations. Thorough evaluation of representativeness of the derived S-Q relation should be performed before it is used for hydrologic analysis.

Myocardial perfusion imaging with technetium-99m SQ30217: Comparison with thallium-201 and coronary anatomy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seldin, D.W.; Johnson, L.L.; Blood, D.K.

1989-03-01

Myocardial perfusion in ten normal volunteers and 20 patients with coronary artery disease documented by recent coronary arteriography was studied with 99mTc-labeled SQ30217 and /sup 201/TI. Plantar /sup 201/TI imaging followed standard treadmill exercise and planar SQ30217 imaging followed upright bicycle exercise, performed to angina, or the same double product achieved on the treadmill test. Upright anterior, 30 degrees left anterior oblique, and 60 degrees left anterior oblique images were obtained for 3, 6, and 9 min, respectively, starting 2 min after injection of 15 mCi of 99mTc SQ30217. A second 15-mCi dose was injected at rest approximately 2 hrmore » later, and the same imaging protocol was followed. No adverse reactions or laboratory abnormalities attributable to SQ30217 were observed. All scans on the normal volunteers were interpreted as normal. Qualitative readings of both tests were equally sensitive for detecting patients with coronary disease (SQ30217 - 16/20, TI - 17/20, p = NS) and identifying abnormal vessels (SQ30217 - 19/45, TI - 21/45, p = NS). Both agents were falsely positive in 1/15 vessels. Ten vascular regions showed persistent abnormalities on resting SQ30217 scans; eight of these were distal to stenoses of at least 90% and three were also abnormal on thallium redistribution images. Hepatic uptake of SQ30217 obscured inferoapical segments in some views in 14/20 patients but did not interfere with abnormal vessel identification.« less

Discovery and characterization of a sulfoquinovose mutarotase using kinetic analysis at equilibrium by exchange spectroscopy

PubMed Central

Abayakoon, Palika; Lingford, James P.; Jin, Yi; Bengt, Christopher; Davies, Gideon J.; Yao, Shenggen; Goddard-Borger, Ethan D.

2018-01-01

Bacterial sulfoglycolytic pathways catabolize sulfoquinovose (SQ), or glycosides thereof, to generate a three-carbon metabolite for primary cellular metabolism and a three-carbon sulfonate that is expelled from the cell. Sulfoglycolytic operons encoding an Embden–Meyerhof–Parnas-like or Entner–Doudoroff (ED)-like pathway harbor an uncharacterized gene (yihR in Escherichia coli; PpSQ1_00415 in Pseudomonas putida) that is up-regulated in the presence of SQ, has been annotated as an aldose-1-epimerase and which may encode an SQ mutarotase. Our sequence analyses and structural modeling confirmed that these proteins possess mutarotase-like active sites with conserved catalytic residues. We overexpressed the homolog from the sulfo-ED operon of Herbaspirillum seropedicaea (HsSQM) and used it to demonstrate SQ mutarotase activity for the first time. This was accomplished using nuclear magnetic resonance exchange spectroscopy, a method that allows the chemical exchange of magnetization between the two SQ anomers at equilibrium. HsSQM also catalyzed the mutarotation of various aldohexoses with an equatorial 2-hydroxy group, including d-galactose, d-glucose, d-glucose-6-phosphate (Glc-6-P), and d-glucuronic acid, but not d-mannose. HsSQM displayed only 5-fold selectivity in terms of efficiency (kcat/KM) for SQ versus the glycolysis intermediate Glc-6-P; however, its proficiency [kuncat/(kcat/KM)] for SQ was 17 000-fold better than for Glc-6-P, revealing that HsSQM preferentially stabilizes the SQ transition state. PMID:29535276

Electric energy production by particle thermionic-thermoelectric power generators

NASA Technical Reports Server (NTRS)

Oettinger, P. E.

1980-01-01

Thermionic-thermoelectric power generators, composed of a thin layer of porous, low work function material separating a heated emitter electrode and a cooler collector electrode, have extremely large Seebeck coefficients of over 2 mV/K and can provide significant output power. Preliminary experiments with 20-micron thick (Ba Sr Ca)O coatings, limited by evaporative loss to temperatures below 1400 K, have yielded short circuit current densities of 500 mA/sq cm and power densities of 60 mW/ sq cm. Substantially more output is expected with cesium-coated refractory oxide particle coatings operating at higher temperatures. Practical generators will have thermal-to-electrical efficiencies of 10 to 20%. Further increases can be gained by cascading these high-temperature devices with lower temperature conventional thermoelectric generators.

Fabrication and performance analysis of 4-sq cm indium tin oxide/InP photovoltaic solar cells

NASA Technical Reports Server (NTRS)

Gessert, T. A.; Li, X.; Phelps, P. W.; Coutts, T. J.; Tzafaras, N.

1991-01-01

Large-area photovoltaic solar cells based on direct current magnetron sputter deposition of indium tin oxide (ITO) into single-crystal p-InP substrates demonstrated both the radiation hardness and high performance necessary for extraterrestrial applications. A small-scale production project was initiated in which approximately 50 ITO/InP cells are being produced. The procedures used in this small-scale production of 4-sq cm ITO/InP cells are presented and discussed. The discussion includes analyses of performance range of all available production cells, and device performance data of the best cells thus far produced. Additionally, processing experience gained from the production of these cells is discussed, indicating other issues that may be encountered when large-scale productions are begun.

Testing of typical spacecraft materials in a simulated substorm environment

NASA Technical Reports Server (NTRS)

Stevens, N. J.; Berkopec, F. D.; Staskus, J. V.; Blech, R. A.; Narciso, S. J.

1977-01-01

The test specimens were spacecraft paints, silvered Teflon, thermal blankets, and solar array segments. The samples, ranging in size from 300 to 1000 sq cm were exposed to monoenergetic electron energies from 2 to 20 keV at a current density of 1 NA/sq cm. The samples generally behaved as capacitors with strong voltage gradient at their edges. The charging characteristics of the silvered Teflon, Kapton, and solar cell covers were controlled by the secondary emission characteristics. Insulators that did not discharge were the spacecraft paints and the quartz fiber cloth thermal blanket sample. All other samples did experience discharges when the surface voltage reached -8 to -16kV. The discharges were photographed. The breakdown voltage for each sample was determined and the average energy lost in the discharge was computed.

Correlation between fabrication factor and superconducting properties of the Tl-and-Bi-based high-Tc superconductor

NASA Technical Reports Server (NTRS)

Maki, Naoki; Okada, Michiya; Doi, Toshiya J.; Kanai, Tsuneyuki; Sato, Junichi; Higashiyama, Kazutoshi

1995-01-01

Large critical current densities (J(sub c)) were obtained in c axis oriented Tl-1 223/Ag composite tapes fabricated by spraying methods without a vacuum. Transport measurements at 77K under a zero field indicated a J(sub c) of 9 x 10(exp 4) A/sq cm and 7 x 10(exp 3) A/sq cm at 1T for the tapes fabricated by spray pyrolysis. The novel GPM method was also applied for Bi-2212/Ag PIT composite wire, and found to be very effective for improving the distribution of voids, which caused from the melt-solidifying process. The GPM showed a marked effect for obtaining homogeneous long wire. A 1 T class coil was successfully fabricated with monocore wire.

Miniature Reservoir Cathode: An Update

NASA Technical Reports Server (NTRS)

Vancil, Bernard K.; Wintucky, Edwin G.

2002-01-01

We report on recent work to produce a small low power, low cost reservoir cathode capable of long life (more than 100,000 hours) at high loading (> 5 A/sq cm). Our objective is a highly manufacturable, commercial device costing less than $30. Small highly loaded cathodes are needed, especially for millimeter wave tubes, where focusing becomes difficult when area convergence ratios are too high. We currently have 3 models ranging from .060-inch diameter to. 125-inch diameter. Reservoir type barium dispenser cathodes have a demonstrated capability for simultaneous high emission density and long life. Seven reservoir cathodes continue to operate on the cathode life test facility at NSWC, Crane, Indiana at 2 and 4 amps/sq cm. They have accumulated nearly 100,000 hours with practically no change in emission levels or knee temperature.

Evaluation of an Ultra-Low Power Reed Solomon Encoder for NASA's Space Technology 5 Mission

NASA Technical Reports Server (NTRS)

Lei, K. E.; Xapsos, M. A.; Poivey, C.; LaBel, K. A.; Stone, R. F.; Yeh, P-S.; Gambles, J.; Hass, J.; Maki, G.; Murguia, J.

2003-01-01

Radiation test results and analyses are presented for ultra-low power Reed Solomon encoder circuits that are being considered for use on the Space Technology 5 (ST5) mission. The total ionizing dose tolerance is in excess of 100 krad(Si) and is due to the low supply voltage and the use of back-bias, which suppresses radiation-induced leakage currents in the n-channel devices. The circuits do not latch-up for ion LET values of at least 90 MeV-sq cm/mg. A hardened-by-design approach to SEU has achieved an upset threshold of about 20 MeV-sq cm/mg. The SEU rate expected for these circuits in the geosynchronous transfer orbit of ST5 is low.

Scholar Quest: A Residency Research Program Aligned with Faculty Goals

PubMed Central

Panchal, Ashish R.; Stolz, Uwe; Denninghoff, Kurt R.; Munger, Benson

2014-01-01

Introduction: The ACGME requires that residents perform scholarly activities prior to graduation, but this is difficult to complete and challenging to support. We describe a residency research program, taking advantage of environmental change aligning resident and faculty goals, to become a contributor to departmental cultural change and research development. Methods: A research program, Scholar Quest (SQ), was developed as a part of an Information Mastery program. The goal of SQ is for residents to gain understanding of scholarly activity through a mentor-directed experience in original research. This curriculum is facilitated by providing residents protected time for didactics, seed grants and statistical/staff support. We evaluated total scholarly activity and resident/faculty involvement before and after implementation (PRE-SQ; 2003–2005 and POST-SQ; 2007–2009). Results: Scholarly activity was greater POST-SQ versus PRE-SQ (123 versus 27) (p<0.05) with an incidence rate ratio (IRR)=2.35. Resident and faculty involvement in scholarly activity also increased PRE-SQ to POST-SQ (22 to 98 residents; 10 to 39 faculty, p<0.05) with an IRR=2.87 and 2.69, respectively. Conclusion: Implementation of a program using department environmental change promoting a resident longitudinal research curriculum yielded increased resident and faculty scholarly involvement, as well as an increase in total scholarly activity. PMID:24868308

Surface Properties of Squalene/Meibum Films and NMR Confirmation of Squalene in Tears

PubMed Central

Ivanova, Slavyana; Tonchev, Vesselin; Yokoi, Norihiko; Yappert, Marta C.; Borchman, Douglas; Georgiev, Georgi As.

2015-01-01

Squalene (SQ) possesses a wide range of pharmacological activities (antioxidant, drug carrier, detoxifier, hydrating, emollient) that can be of benefit to the ocular surface. It can come in contact with human meibum (hMGS; the most abundant component of the tear film lipid layer) as an endogenous tear lipid or from exogenous sources as eyelid sebum or pharmaceuticals. The aims of this study were to determine (i) if SQ is in tear lipids and (ii) its influence on the surface properties of hMGS films. Heteronuclear single quantum correlation NMR confirmed 7 mol % SQ in Schirmer’s strips extracts. The properties of SQ/hMGS pseudo-binary films at the air/water interface were studied with Langmuir surface balance, stress-relaxation dilatational rheology and Brewster angle microscopy. SQ does not possess surfactant properties. When mixed with hMGS squalene (i) localized over the layers’ thinner regions and (ii) did not affect the film pressure at high compression. Therefore, tear SQ is unlikely to instigate dry eye, and SQ can be used as a safe and “inert” ingredient in formulations to protect against dry eye. The layering of SQ over the thinner film regions in addition to its pharmacological properties could contribute to the protection of the ocular surface. PMID:26370992

Effect of SQ29,852, a new angiotensin converting enzyme (ACE) inhibitor with a phosphonic acid group, on the activity of angiotensin converting enzyme from human kidney.

PubMed

Hiwada, K; Inoue, Y; Kokubu, T

1990-01-01

1. An in vitro experiment was carried out to compare the inhibitory effect of SQ29,852 on human renal angiotensin converting enzyme (ACE) with those of captopril, enalapril and enalaprilat. 2. SQ29,852 strongly inhibited human renal ACE; its IC50 value was 1.5 x 10(-8) M. In terms of the IC50, SQ29,852's efficacy was about 1/10 of that of captopril and 1/28 of that of enalaprilat, but it was about 14 times more potent than enalapril. 3. SQ29,852 showed no inhibitory effects on cathepsin D, urinary kallikrein, renal renin, pepsin, trypsin and chymotrypsin. Its ACE-specificity was higher than that of captopril. 4. ACE inhibition by SQ29,852 was shown to be competitive, as revealed by Lineweaver-Burk plots. The affinity of SQ29,852 to ACE was shown to be high by a Ki value of 1.2 x 10(-8) M.

One-man electrochemical air revitalization system evaluation

NASA Technical Reports Server (NTRS)

Schbert, F. H.; Marshall, R. D.; Hallick, T. M.; Woods, R. R.

1976-01-01

A program to evaluate the performance of a one man capacity, self contained electrochemical air revitalization system was successfully completed. The technology readiness of this concept was demonstrated by characterizing the performance of this one man system over wide ranges in cabin atmospheric conditions. The electrochemical air revitalization system consists of a water vapor electrolysis module to generate oxygen from water vapor in the cabin air, and an electrochemical depolarized carbon dioxide concentrator module to remove carbon dioxide from the cabin air. A control/monitor instrumentation package that uses the electrochemical depolarized concentrator module power generated to partially offset the water vapor electrolysis module power requirements and various structural fluid routing components are also part of the system. The system was designed to meet the one man metabolic oxygen generation and carbon dioxide removal requirements, thereby controlling cabin partial pressure of oxygen at 22 kN/sq m and cabin pressure of carbon dioxide at 400 N/sq m over a wide range in cabin air relative humidity conditions.

Ca-Rich Carbonate Melts: A Regular-Solution Model, with Applications to Carbonatite Magma + Vapor Equilibria and Carbonate Lavas on Venus

NASA Technical Reports Server (NTRS)

Treiman, Allan H.

1995-01-01

A thermochemical model of the activities of species in carbonate-rich melts would be useful in quantifying chemical equilibria between carbonatite magmas and vapors and in extrapolating liquidus equilibria to unexplored PTX. A regular-solution model of Ca-rich carbonate melts is developed here, using the fact that they are ionic liquids, and can be treated (to a first approximation) as interpenetrating regular solutions of cations and of anions. Thermochemical data on systems of alkali metal cations with carbonate and other anions are drawn from the literature; data on systems with alkaline earth (and other) cations and carbonate (and other) anions are derived here from liquidus phase equilibria. The model is validated in that all available data (at 1 kbar) are consistent with single values for the melting temperature and heat of fusion for calcite, and all liquidi are consistent with the liquids acting as regular solutions. At 1 kbar, the metastable congruent melting temperature of calcite (CaCO3) is inferred to be 1596 K, with (Delta)bar-H(sub fus)(calcite) = 31.5 +/- 1 kJ/mol. Regular solution interaction parameters (W) for Ca(2+) and alkali metal cations are in the range -3 to -12 kJ/sq mol; W for Ca(2+)-Ba(2+) is approximately -11 kJ/sq mol; W for Ca(2+)-Mg(2+) is approximately -40 kJ/sq mol, and W for Ca(2+)-La(3+) is approximately +85 kJ/sq mol. Solutions of carbonate and most anions (including OH(-), F(-), and SO4(2-)) are nearly ideal, with W between 0(ideal) and -2.5 kJ/sq mol. The interaction of carbonate and phosphate ions is strongly nonideal, which is consistent with the suggestion of carbonate-phosphate liquid immiscibility. Interaction of carbonate and sulfide ions is also nonideal and suggestive of carbonate-sulfide liquid immiscibility. Solution of H2O, for all but the most H2O-rich compositions, can be modeled as a disproportionation to hydronium (H3O(+)) and hydroxyl (OH(-)) ions with W for Ca(2+)-H3O(+) (approximately) equals 33 kJ/sq mol. The regular-solution model of carbonate melts can be applied to problems of carbonatite magma + vapor equilibria and of extrapolating liquidus equilibria to unstudied systems. Calculations on one carbonatite (the Husereau dike, Oka complex, Quebec, Canada) show that the anion solution of its magma contained an OH mole fraction of (approximately) 0.07, although the vapor in equilibrium with the magma had P(H2O) = 8.5 x P(CO2). F in carbonatite systems is calculated to be strongly partitioned into the magma (as F(-)) relative to coexisting vapor. In the Husereau carbonatite magma, the anion solution contained an F(-) mole fraction of (approximately) 6 x 10(exp -5).

Applications of HCMM data to soil moisture snow and estuarine current studies. [Cooper River and Delaware Bay

NASA Technical Reports Server (NTRS)

Wiesnet, D. R. (Principal Investigator); Mcginnis, D. F.; Matson, M.

1980-01-01

The author has identified the following significant results. The HCMM thermal data are useful for monitoring estuarine surface thermal patterns. Estuarine thermal patterns, are, under certain conditions, indicative of the surface tidal current circulation patterns. Under optimum conditions, estuaries as small as the Cooper River (i.e., approximately 100 sq km) can be monitored for tidal/thermal circulation patterns by HCMM-type IR sensors.

An X-ray survey of nine historical novae. [HEAO 2 observations

NASA Technical Reports Server (NTRS)

Becker, R. H.; Marshall, F. E.

1980-01-01

The Einstein Observatory imaging proportional counter was used to search for X-ray emission from nine nearby historical novae. Six of the novae were detected with estimated X-ray intensities between .1 to 4 keV of 10 to the -13th power to 10 to the -11th power ergs/sq cm-s, comparable to the intensities of previously detected cataclysmic variables. The X-ray intensity of one of the novae, V603 Aql, varies over times of several hundred seconds. The data suggest a correlation between the decay rate of the historical outburst and the current X-ray luminosity. Alternatively, the X-ray luminosity may be related to the inclination of the binary system.

Sin(x)**2 + cos(x)**2 = 1. [programming identities using comparative combinatorial substitutions

NASA Technical Reports Server (NTRS)

Stoutemyer, D. R.

1977-01-01

Attempts to achieve tasteful automatic employment of the identities sin sq x + cos sq x = 1 and cos sq h x -sin sq h x = 1 in a manner which truly minimizes the complexity of the resulting expression are described. The disappointments of trigonometric reduction, trigonometric expansion, pattern matching, Poisson series, and Demoivre's theorem are related. The advantages of using the method of comparative combinatorial substitutions are illustrated.

Regional thermal and electric energy output of salt-gradient solar ponds in the U.S.

NASA Technical Reports Server (NTRS)

Singer, M. J.; Lin, E. I. H.

1982-01-01

Salt-gradient solar pond thermal and electrical energy output was calculated for each of twelve regions within the United States as part of an effort to assess solar pond applicability and extent of requisite physical resources on a regional basis. The energy output level is one of the key factors affecting the economic feasibility of solar ponds. Calculated thermal energy output ranges from 6.9 Wt/sq m in Fairbanks, Alaska, to 73.1 Wt/sq m in Daggett, California, at an energy extraction temperature of 45 C. The output ranges from 0.0 Wt/sq m in Fairbanks to 63.2 Wt/sq m in Daggett at 60 C. Electrical energy output ranges from 0.0 We/sq m in Fairbanks to 3.11 We/sq m in Daggett. Although these estimates constitute a reasonable basis for regional comparison, site-specific analysis must be performed for an actual application design.

An ultrahigh vacuum, low-energy ion-assisted deposition system for III-V semiconductor film growth

NASA Astrophysics Data System (ADS)

Rohde, S.; Barnett, S. A.; Choi, C.-H.

1989-06-01

A novel ion-assisted deposition system is described in which the substrate and growing film can be bombarded with high current densities (greater than 1 mA/sq cm) of very low energy (10-200 eV) ions. The system design philosophy is similar to that used in III-V semiconductor molecular-beam epitaxy systems: the chamber is an all-metal ultrahigh vacuum system with liquid-nitrogen-cooled shrouds, Knudsen-cell evaporation sources, a sample insertion load-lock, and a 30-kV reflection high-energy electron diffraction system. III-V semiconductor film growth is achieved using evaporated group-V fluxes and group-III elemental fluxes sputtered from high-purity targets using ions extracted from a triode glow discharge. Using an In target and an As effusion cell, InAs deposition rates R of 2 microns/h have been obtained. Epitaxial growth of InAs was observed on both GaSb(100) and Si(100) substrates.

Service quality from the perspective of myocardial infarction patients.

PubMed

Gholipour, Kamal; Tabrizi, Jafar Sadegh; Azimzadeh, Solmaz; Ghafari, Samad; Iezadi, Shabnam

2018-04-01

Service quality (SQ) generally refers to the nonclinical aspects of health services and primarily focuses on the relationship between the care provider and the customers, and the environment in which care services are delivered. The aim of this study was to assess the SQ provided for myocardial infarction (MI) from the patients' perspective. A cross-sectional study was conducted with 164 patients with MI at the Tabriz Shahid Madani cardiology clinic. Study participants were selected using convenience sampling. SQ was measured using a validated Comprehensive Quality Measurement in Healthcare SQ questionnaire. The reliability was confirmed based on Cronbach's alpha coefficient (α=0.81). SQ was calculated using the formula SQ=10- (importance × performance), based on the importance and performance of non-health-related aspects from the customers' perspective. Importance scores ranged from 1 to 10 and performance was scored between 0 and 1. Of 164 participants, about 75% were men and almost 44% were between 51 and 65 years of age. From the customers' perspective, the total SQ score was 6.80 (0-10 scale), and the individual scores for all SQ aspects were below an acceptable level. Confidentiality, dignity and continuity were given the highest scores, while availability of support groups had the lowest score. The study findings revealed an opportunity to improve SQ. Patient and provider participation in quality improvement activities could be an effective strategy to improve the aspects of health care quality that were most important to the customers and those with low scores, such as availability of support groups.

Hydrologic reconnaissance of the Unalakleet River basin, Alaska, 1982-83

USGS Publications Warehouse

Sloan, C.E.; Kernodle, D.R.; Huntsinger, Ronald

1986-01-01

The Unalakleet River, Alaska, from its headwaters to the confluence of the Chiroskey River has been designated as a wild river and is included in the National Wild and Scenic Rivers System. Yearly low flow, which occurs during the winter, is sustained by groundwater discharge; there are few lakes in the basin and the cold climate prevents winter runoff. The amount of winter streamflow was greatest in the lower parts of streams with the exception of the South River and was apparently proportional to the amount of unfrozen alluvium upstream from the measuring sites. Unit discharge in late winter ranged from nearly zero at the mouth of the South River to 0.24 cu ft/sec/sq mi in the Unalakleet River main stem below Tenmile River. Summer runoff at the time of the reconnaissance may have been slightly higher than normal owing to recent rains. Unit runoff ranged from a low of 1.0 cu ft/sec/sq mi at the South River, to a high value of 2.4 cu ft/sec/sq mi at the North Fork Unalakleet River. Flood marks were present in the basin well above streambank levels but suitable sections to measure the maximum evident flood by slope-area methods were not found. Flood peaks were calculated for the Unalakleet River and its tributaries using basin characteristics. Calculated unit runoff for the 50-year flood ranged from about 17 to 45 cu ft/sec/sq mi. Water quality was good throughout the basin, and an abundant and diversified community of benthic invertebrates was found in samples collected during the summer reconnaissance. Permafrost underlies most of the basin, but groundwater can be found in unfrozen alluvium in the stream valleys, most abundantly in the lower part of the main tributaries and along the main stem of the Unalakleet River. Groundwater sustains river flow through the winter; an estimate of its quantity can be found through low-flow measurements. Groundwater quality in the basin appears to be satisfactory for most uses. Currently, little groundwater is used within the basin. The water supply for Unalakleet is obtained from a well and gallery in a small valley north of the airport, outside the Unalakleet River basin. (Author 's abstract)

Quantitative Assessment of Spatio-Temporal Desertification Rates in Azerbaijan during Using Timeseries Landsat-8 Satellite Images

NASA Astrophysics Data System (ADS)

Bayramov, Emil; Mammadov, Ramiz

2016-07-01

The main goals of this research are the object-based landcover classification of LANDSAT-8 multi-spectral satellite images in 2014 and 2015, quantification of Normalized Difference Vegetation Indices (NDVI) rates within the land-cover classes, change detection analysis between the NDVIs derived from multi-temporal LANDSAT-8 satellite images and the quantification of those changes within the land-cover classes and detection of changes between land-cover classes. The object-based classification accuracy of the land-cover classes was validated through the standard confusion matrix which revealed 80 % of land-cover classification accuracy for both years. The analysis revealed that the area of agricultural lands increased from 30911 sq. km. in 2014 to 31999 sq. km. in 2015. The area of barelands increased from 3933 sq. km. in 2014 to 4187 sq. km. in 2015. The area of forests increased from 8211 sq. km. in 2014 to 9175 sq. km. in 2015. The area of grasslands decreased from 27176 sq. km. in 2014 to 23294 sq. km. in 2015. The area of urban areas increased from 12479 sq. km. in 2014 to 12956 sq. km. in 2015. The decrease in the area of grasslands was mainly explained by the landuse shifts of grasslands to agricultural and urban lands. The quantification of low and medium NDVI rates revealed the increase within the agricultural, urban and forest land-cover classes in 2015. However, the high NDVI rates within agricultural, urban and forest land-cover classes in 2015 revealed to be lower relative to 2014. The change detection analysis between landscover types of 2014 and 2015 allowed to determine that 7740 sq. km. of grasslands shifted to agricultural landcover type whereas 5442sq. km. of agricultural lands shifted to rangelands. This means that the spatio-temporal patters of agricultural activities occurred in Azerbaijan because some of the areas reduced agricultural activities whereas some of them changed their landuse type to agricultural. Based on the achieved results, it is possible to conclude that the area of agricultural lands in Azerbaijan increased from 2014 to 2015. The crop productivity also increased in the croplands, however some of the areas showed lower productivity in 2015 relative to 2014.

Comparison between the magnetic and transport critical current densities in high critical current density melt-textured yttrium barium copper-oxide

NASA Technical Reports Server (NTRS)

Gao, L.; Meng, R. L.; Xue, Y. Y.; Hor, P. H.; Chu, C. W.

1991-01-01

Using a recently developed pulsed critical current density (Jc) measuring system, the Jc of the high-Jc melt-textured YBa2Cu3O(7-delta) (Y123) bulk samples has been determined. I-V curves with a voltage resolution of 0.5 microV were obtained, and transport Jc's along the a-b plane as high as 7.2 x 10 to the 4th A/sq cm were extracted. These results are comparable to the values obtained magnetically. On the other hand, transport Jc along the c axis were found to be two orders of magnitude smaller, even though the magnetic Jc along the c axis is only about five times smaller than Jc along the a-b plane. It is suggested that for the high-temperature superconducting materials which are highly anisotropic, caution should be taken when using the nontransport magnetic methods to determine Jc.

Thermal surveillance of active volcanoes using the LANDSAT-1 data collection system. Part 3: Heat discharge from Mount St. Helens, Washington

NASA Technical Reports Server (NTRS)

Friedman, J. D.; Frank, D. (Principal Investigator)

1977-01-01

The author has identified the following significant results. Two thermal anomalies, A at 2740 m altitude on the north slope, and B between 2650 and 2750 m altitude on the southwest slope at the contact of the dacite summit dome of Mount St. Helens, Washington were confirmed by aerial infrared scanner surveys between 1971 and 1973. LANDSAT 1 data collection platform 6166, emplaced at site B anomaly, transmitted 482 sets of temperature values in 1973 and 1974, suitable for estimating the differential radiatin emission as 84 W/sq m, approximately equivalent to the Fourier conductive flux of 89 W/sq m in the upper 15 cm below the surface. The differential geothermal flux, including heat loss via evaporation and convection, was estimated at 376 W/sq m. Total energy yield of Mount St. Helens probably ranges between 0.1 and 0.4 x 10 to the 6th power W.

Electronic and transport properties of Cobalt-based valence tautomeric molecules and polymers

NASA Astrophysics Data System (ADS)

Chen, Yifeng; Calzolari, Arrigo; Buongiorno Nardelli, Marco

2011-03-01

The advancement of molecular spintronics requires further understandings of the fundamental electronic structures and transport properties of prototypical spintronics molecules and polymers. Here we present a density functional based theoretical study of the electronic structures of Cobalt-based valence tautomeric molecules Co III (SQ)(Cat)L Co II (SQ)2 L and their polymers, where SQ refers to the semiquinone ligand, and Cat the catecholate ligand, while L is a redox innocent backbone ligand. The conversion from low-spin Co III ground state to high-spin Co II excited state is realized by imposing an on-site potential U on the Co atom and elongating the Co-N bond. Transport properties are subsequently calculated by extracting electronic Wannier functions from these systems and computing the charge transport in the ballistic regime using a Non-Equilibrium Green's Function (NEGF) approach. Our transport results show distinct charge transport properties between low-spin ground state and high-spin excited state, hence suggesting potential spintronics devices from these molecules and polymers such as spin valves.

Implementation of a Thick-Film Composite Li-Ion Microcathode Using Carbon Nanotubes as the Conductive Filler

NASA Technical Reports Server (NTRS)

Lin, Qian; Harb, John N.

2004-01-01

This paper describes the development of a thick-film microcathode for use in Li-ion microbatteries in order to provide increased power and energy per area. These cathodes take advantage of a composite porous electrode structure, utilizing carbon nanotubes (CNT) as the conductive filler. The use of carbon nanotubes was found to significantly reduce the measured resistance of the electrodes, increase active material accessibility, and improve electrode performance. In particular, the cycling and power performance of the thick-film cathodes was significantly improved, and the need for compression was eliminated. Cathode thickness and CNT content were optimized to maximize capacity and power performance. Power capability of >50 mW/sq cm (17 mA/sq cm) with discharge capacity of >0.17 mAh/sq cm was demonstrated. The feasibility of fabricating thick-film microcathodes capable of providing the power and capacity needed for use in autonomous microsensor systems was also demonstrated.

Growth of young saligna eucalyptus in Hawaii: 6 years after thinning

Treesearch

Craig D. Whitesell

1975-01-01

The effect of thinning on growth rate and quality of a 6-year-old Eucalyptus saligna Sm. stand on Maui, Hawaii, was studied by testing three levels of thinning from below: 100, 85, and 70 sq ft per acre (23, 19.5, and 16 sq m/ha). The stand had an average basal area of 102 sq ft per acre (23 sq m/ha). Initial spacing was about 10 by 10 feet. During...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tu, J.I.; Brennan, J.; Stouffer, B.

Fosinopril (SQ 28,555) is a member of a new chemical class of angiotensin converting enzyme inhibitors being developed by The Squibb Institute for Medical Research. During or following absorption, fosinopril, a prodrug, is hydrolyzed pharmacologically to the active diacid, SQ 27,519. A specific radioimmunoassay (RIA) for the measurement of SQ 27,519 in human serum has been developed. The assay utilizes a specific SQ 27,519 antibody, 125I-iodohistamine-SQ 27,519 radiolabel, and human serum standards. Satisfactory zero binding and assay sensitivity are achieved after a 2-h incubation at room temperature. Separation of the antibody-bound and free radiolabeled antigens is achieved by using polyethylenemore » glycol-goat anti-rabbit gamma globulin separant. Recovery efficiencies ranged from 97.2 to 109.4%. The assay exhibited little or no cross-reactivity with captopril. Cross-reactivities for prodrug (SQ 28,555) and phenolic SQ 27,519 were 5 and 9%, respectively. Intra-assay variability (3.3-5.6%) and interassay variability (7.1-6.6%) were observed. Linear regression analysis indicates that RIA and (14C) thin-layer radiochromatography (TLRC) methods gave a highly significant correlation (RIA = 1.0 (14C)TLRC + 0.17, r = 0.991). Pharmacokinetic profiles of patient sera containing SQ 27,519 obtained by RIA and (14C)TLRC are identical. The RIA has been used routinely in support of the bioavailability and pharmacokinetic studies of fosinopril in humans.« less

77 FR 15788 - Federal Property Suitable as Facilities To Assist the Homeless

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-16

... conditions--need repairs; lead based paint, asbestos, and mold identified B-710 43901 Oak St. Selfridge MI... removal only; 1,843 sq. ft.; current use: Admin. office; need repairs; asbestos possible B-326 29865... repairs; possible asbestos Missouri Whiteman-Annex No.3 312 Northern Hill Rd. Warrensburg MO 64093...

Very High Current Density Nb/AlN/Nb Tunnel Junctions for Low-Noise Submillimeter Mixers

NASA Technical Reports Server (NTRS)

Kawamura, Jonathan; Miller, David; Chen, Jian; Zmuidzinas, Jonas; Bumble, Bruce; LeDuc, Henry G.; Stern, Jeff A.

2000-01-01

We have fabricated and tested submillimeter-wave superconductor-insulator-superconductor (SIS) mixers using very high current density Nb/AlN/Nb tunnel junctions (J(sub c) approximately equal 30 kA/sq cm) . The junctions have low resistance-area products (R(sub N)A approximately 5.6 Omega.sq micron), good subgap to normal resistance ratios R(sub sg)/R(sub N) approximately equal 10, and good run-to-run reproducibility. From Fourier transform spectrometer measurements, we infer that omega.R(sub N)C = 1 at 270 GHz. This is a factor of 2.5 improvement over what is generally available with Nb/AlO(x)/Nb junctions suitable for low-noise mixers. The AlN-barrier junctions are indeed capable of low-noise operation: we measure an uncorrected receiver noise temperature of T(sub RX) = 110 K (DSB) at 533 GHz for an unoptimized device. In addition to providing wider bandwidth operation at lower frequencies, the AlN-barrier junctions will considerably improve the performance of THz SIS mixers by reducing RF loss in the tuning circuits.

Emerging materials for solar cell applications: Electrodeposited CdTe

NASA Astrophysics Data System (ADS)

Rod, R. L.; Basol, B. M.; Stafsudd, O.

1980-09-01

Work was centered about improving electroplating processes and cell fabrication techniques, with emphasis being given to three differing n-CdTe/Au Schottky configurations. The highest values of efficiency related parameters achieved with a simulated solar irradiation of 100 mW/sq cm were 0.57V for open circuit voltage, 0.6 for fill factor, and 6 mA/sq cm for short circuit current. Four important parameters are known to control the quality of the Monosolar electrodeposition process and resultant solar cells. They are electrolyte temperature, Te concentration in the solution at a specific pH, deposition or quasi-rest potential, and flow pattern of the electrolyte (stirring). The first three considerations are believed to be fully understood and optimized. Work is underway to further understand the effects of stirring on the diffusion of ionic components and the effects on CdTe film performance. Work was accelerated during the quarter to increase the short circuit current. Parallel programs using laser irradiation of finished CdTe films, heat treatment, and changes in the electrodeposition process itself to recrystallize films were started.

Performance improvements of the vertical, double-diffused power metal-oxide-silicon field-effect transistor

NASA Astrophysics Data System (ADS)

Zhu, Ronghua

An n-channel power vertical double-diffused metal-oxide-silicon field-effect transistor (VDMOSFET) with a new atomic-lattice-layout (ALL) has been designed and fabricated. The performance of the VDMOSFET with the ALL has been studied experimentally and comprehensively for the first time. The experimental results with the ALL are compared with the square (SQ), hexagonal (HEX) and stripe (STR) layouts for different applications. For high-frequency applications of VDMOSFET, the ALL is superior to the HEX and inferior to the STR. The optimum specific on-resistance and input capacitance product (Rsb{ON,SP} × Csb{iss,SP}) and optimum specific on-resistance and output capacitance product (Rsb{ON,SP} × Csb{oss,SP}) for the ALL are 44% and 36% lower than the HEX, and 10% and 13% higher than the STR, respectively. The ALL offers superior performance compared to the SQ for applications involving smart power feedback control using integrated current sensor. For a typical sense resistance of 100 Omega, the sense current drops 44% of its value at 0 Omega for the SQ, but only 11% for the ALL. For high-voltage and high-current applications, such as voltage-controlled current source, one observes that the ALL enters into quasi-saturation region at lower gate voltage (Vsb{G}). Typically, quasi-saturation occurs at Vsb{G} of 3V above the threshold voltage (Vsb{T}) for ALL, whereas this voltage is 5 and 6V for the STR and HEX, respectively. Minority carrier lifetime control by proton implantation has been successfully employed to improve the VDMOSFET built-in diode switching performance for the first time. A sevenfold reduction in reverse recovery charge has been achieved with a proton energy of 2.5 MeV and dose of 3 × 10sp{11}/cmsp2. The impact of proton implantation on diode forward voltage and the VDMOSFET characteristics, such as Vsb{T}, leakage current and on-resistance, has been found negligible. Proton implantation has also been found to significantly improve the device ruggedness. The peak reverse current of the built-in diode is reduced to 17.6 A for a proton energy of 1.5 MeV compared to 29.1 A for an un-implanted device at di/dt = 450 A/mus. The optimum location of the proton has been found at approximately middle of the epi-layer.

Microfacies and depositional environments of the Late Ordovician Lianglitage Formation at the Tazhong Uplift in the Tarim Basin of Northwest China

NASA Astrophysics Data System (ADS)

Gao, Da; Lin, Changsong; Yang, Haijun; Zuo, Fanfan; Cai, Zhenzhong; Zhang, Lijuan; Liu, Jingyan; Li, Hong

2014-04-01

The Late Ordovician Lianglitage Formation comprises 13 microfacies (Mf1-Mf13) that were deposited on a carbonate platform at the Tazhong Uplift of the Tarim Basin in Northwest China. Each type of microfacies indicates a specific depositional environment with a certain level of wave energy. Four primary groups of microfacies associations (MA1-MA4) were determined. These associations represent different depositional facies, including reef-shoal facies in the platform margin (MA1), carbonate sand shoal facies (MA2) and oncoid shoal (MA3) on open platforms, and lagoon and tidal flat facies (MA4) in the platform interior. Each microfacies association was generated in a fourth-order sedimentary sequence developing within third-order sequences (SQ1, SQ2, and SQ3, from bottom to top), showing a shallowing-upward trend. High-frequency sequences and facies correlation between wells suggests that the reef-shoal facies more successively developed in the southeastern part of the platform margin, and high-energy microfacies were more strictly confined by the top boundary of fourth-order sequences in the northwestern part of the platform. The highstand systems tract (HST) of the SQ2 is characterized by reef-shoals that developed along the platform margin and tidal flats and lagoons that developed in the platform interior, while the SQ3 is characterized by the oncoid shoal facies that generally developed on the uplift due to a regionally extensive transgression that occurred during the latter part of the Late Ordovician. The results of this study can be used for investigating the development and distribution of potential reservoirs; the reservoirs in southeastern part of the platform margin may be of premium quality because the high-energy microfacies were best preserved there.

Power-Efficient, High-Current-Density, Long-Life Thermionic Cathode Developed for Microwave Amplifier Applications

NASA Technical Reports Server (NTRS)

Wintucky, Edwin G.

2002-01-01

A power-efficient, miniature, easily manufactured, reservoir-type barium-dispenser thermionic cathode has been developed that offers the significant advantages of simultaneous high electron-emission current density (>2 A/sq cm) and very long life (>100,000 hr of continuous operation) when compared with the commonly used impregnated-type barium-dispenser cathodes. Important applications of this cathode are a wide variety of microwave and millimeter-wave vacuum electronic devices, where high output power and reliability (long life) are essential. We also expect it to enable the practical development of higher purveyance electron guns for lower voltage and more reliable device operation. The low cathode heater power and reduced size and mass are expected to be particularly beneficial in traveling-wave-tube amplifiers (TWTA's) for space communications, where future NASA mission requirements include smaller onboard spacecraft systems, higher data transmission rates (high frequency and output power) and greater electrical efficiency.

Ion extraction capabilities of closely spaced grids

NASA Technical Reports Server (NTRS)

Rovang, D. C.; Wilbur, P. J.

1982-01-01

The ion extraction capabilities of accelerator systems with small screen hole diameters (less than 2.0 mm) are investigated at net-accelerating voltages of 100, 300, and 500 V. Results show that the impingement-limited perveance is not dramatically affected by reductions in screen hole diameter to 1.0 mm, but impingement-limited performance was found to be dependent on the grid separation distance, the discharge-to-total accelerating voltage ratio, and the net-to-total accelerating voltage ratio. Results obtained using small hole diameters and closely spaced grids indicate a new mode of grid operation where high current density operation can be achieved with a specified net acceleration voltage by operating the grids at a high rather than low net-to-total acceleration voltage. Beam current densities as high as 25 mA/sq cm were obtained using grids with 1.0 mm diameter holes operating at a net accelerating voltage of 500 V.

Magnetic field and electric current structure in the chromosphere

NASA Technical Reports Server (NTRS)

Dravins, D.

1974-01-01

The three-dimensional vector magnetic field structure in the chromosphere above an active region is deduced by using high-resolution H-alpha filtergrams together with a simultaneous digital magnetogram. An analog model of the field is made with 400 metal wires representing field lines that outline the H-alpha structure. The height extent of the field is determined from vertical field-gradient observations around sunspots, from observed fibril heights, and from an assumption that the sources of the field are largely local. The computed electric currents (typically 10 mA/sq m) are found to flow in patterns not similar to observed features and not parallel to magnetic fields. Force structures correspond to observed solar features; the dynamics to be expected include: downward motion in bipolar areas in the lower chromosphere, an outflow of the outer chromosphere into the corona with radially outward flow above bipolar plage regions, and motion of arch filament systems.

Skill Assessment of a Spectral Ocean-Atmosphere Radiative Model

NASA Technical Reports Server (NTRS)

Gregg, Watson, W.; Casey, Nancy W.

2009-01-01

Ocean phytoplankton, detrital material, and water absorb and scatter light spectrally. The Ocean- Atmosphere Spectral Irradiance Model (OASIM) is intended to provide surface irradiance over the oceans with sufficient spectral resolution to support ocean ecology, biogeochemistry, and heat exchange investigations, and of sufficient duration to support inter-annual and decadal investigations. OASIM total surface irradiance (integrated 200 nm to 4 microns) was compared to in situ data and three publicly available global data products at monthly 1-degree resolution. OASIM spectrally-integrated surface irradiance had root mean square (RMS) difference= 20.1 W/sq m (about 11%), bias=1.6 W/sq m (about 0.8%), regression slope= 1.01 and correlation coefficient= 0.89, when compared to 2322 in situ observations. OASIM had the lowest bias of any of the global data products evaluated (ISCCP-FD, NCEP, and ISLSCP 11), and the best slope (nearest to unity). It had the second best RMS, and the third best correlation coefficient. OASIM total surface irradiance compared well with ISCCP-FD (RMS= 20.7 W/sq m; bias=-11.4 W/sq m, r=0.98) and ISLSCP II (RMS =25.2 W/sq m; bias= -13.8 W/sq m; r=0.97), but less well with NCEP (RMS =43.0 W/sq m ;bias=-22.6 W/sq m; x=0.91). Comparisons of OASIM photosynthetically available radiation (PAR) with PAR derived from SeaWiFS showed low bias (-1.8 mol photons /sq m/d, or about 5%), RMS (4.25 mol photons /sq m/d ' or about 12%), near unity slope (1.03) and high correlation coefficient (0.97). Coupled with previous estimates of clear sky spectral irradiance in OASIM (6.6% RMS at 1 nm resolution), these results suggest that OASIM provides reasonable estimates of surface broadband and spectral irradiance in the oceans, and can support studies on ocean ecosystems, carbon cycling, and heat exchange.

Difference in Postsurgical Prognostic Factors between Lung Adenocarcinoma and Squamous Cell Carcinoma

PubMed Central

Sakai, Hiroki; Kimura, Hiroyuki; Miyazawa, Tomoyuki; Marushima, Hideki; Saji, Hisashi

2017-01-01

Purpose: The aim of this study was to compare the clinicopathologic prognostic factors between patients who underwent lung resection for adenocarcinoma (AD) and those with squamous cell carcinoma (SQ). Methods: A database of patients with lung AD or SQ who underwent surgery with curative intent in our department from January 2008 to December 2014 was reviewed. Associations between various clinicopathologic factors, postsurgical recurrence-free survival (RFS), and overall survival (OS) were analyzed to find significant prognostic factors. Results: A total of 537 lung cancer patients (AD, 434; SQ, 103) were included in this study. Although RFS was similar in patients with AD and SQ, OS was significantly poorer in those with SQ. Multivariate analysis in patients with AD revealed that age (≥69 vs. <69), lymphatic invasion, and histologic pleural invasion (p0 vs. p1–3) were associated with RFS, while gender and pleural invasion were associated with OS. In SQ, however, smoking, clinical stage, and pulmonary metastasis were associated with RFS in the multivariate analysis. Conclusion: Since significant postoperative prognostic factors are quite different between lung AD and SQ, these two histologic types should be differently analyzed in a clinical study. PMID:28966230

Radiative Effects of African Dust and Smoke Observed from CERES and CALIOP Data

NASA Technical Reports Server (NTRS)

Yorks, John E.; McGill, Matt; Rodier, Sharon; Vaughan, Mark; Xu, Yongxiang; Hlavka, Dennis

2009-01-01

Cloud and aerosol effects have a significant impact on the atmospheric radiation budget in the Tropical Atlantic because of the spatial and temporal extent of desert dust and smoke from biomass burning in the atmosphere. The influences of African dust and smoke aerosols on cloud radiative properties over the Tropical Atlantic Ocean were analyzed for the month of July for three years (2006-2008) using collocated data collected by the Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) and Clouds and the Earth s Radiant Energy System (CERES) instruments on the CALIPSO and Aqua satellites. Aerosol layer height and type can be more accurately determined using CALIOP data, through parameters such as cloud and aerosol layer height, optical depth and depolarization ratio, than data from atmospheric imagers used in previous cloud-aerosol interaction studies. On average, clouds below 5 km had a daytime instantaneous shortwave (SW) radiative flux of 270.2 +/- 16.9 W/sq m and thin cirrus clouds had a SW radiative flux of 208.0 +/- 12.7 W/sq m. When dust aerosols interacted with clouds below 5 km, as determined from CALIPSO, the SW radiative flux decreased to 205.4 +/- 13.0 W/sq m. Similarly, smoke aerosols decreased the SW radiative flux of low clouds to a value of 240.0 +/- 16.6 W/sq m. These decreases in SW radiative flux were likely attributed to the aerosol layer height and changes in cloud microphysics. CALIOP lidar observations, which more accurately identify aerosol layer height than passive instruments, appear essential for better understanding of cloud-aerosol interactions, a major uncertainty in predicting the climate system.

Structure factor of blends of solvent-free nanoparticle-organic hybrid materials: density-functional theory and small angle X-ray scattering.

PubMed

Yu, Hsiu-Yu; Srivastava, Samanvaya; Archer, Lynden A; Koch, Donald L

2014-12-07

We investigate the static structure factor S(q) of solvent-free nanoparticle-organic hybrid materials consisting of silica nanocores and space-filling polyethylene glycol coronas using a density-functional theory and small angle X-ray scattering measurements. The theory considers a bidisperse suspension of hard spheres with different radii and tethered bead-spring oligomers with different grafting densities to approximate the polydispersity effects in experiments. The experimental systems studied include pure samples with different silica core volume fractions and the associated mean corona grafting densities, and blends with different mixing ratios of the pure samples, in order to introduce varying polydispersity of corona grafting density. Our scattering experiments and theory show that, compared to the hard-sphere suspension with the same core volume fraction, S(q) for pure samples exhibit both substantially smaller values at small q and stronger particle correlations corresponding to a larger effective hard core at large q, indicating that the tethered incompressible oligomers enforce a more uniform particle distribution, and the densely grafted brush gives rise to an additional exclusionary effect between the nanoparticles. According to the theory, polydispersity in the oligomer grafting density controls the deviation of S(q) from the monodisperse system at smaller q, and the interplay of the enhanced effective core size and the entropic attraction among the particles is responsible for complex variations in the particle correlations at larger q. The successful comparison between the predictions and the measurements for the blends further suggests that S(q) can be used to assess the uniformity of grafting density in polymer-grafted nanoparticle materials.

Determination of Unfiltered Radiances from the Clouds and the Earth's Radiant Energy System (CERES) Instrument

NASA Technical Reports Server (NTRS)

Loeb, N. G.; Priestley, K. J.; Kratz, D. P.; Geier, E. B.; Green, R. N.; Wielicki, B. A.; Hinton, P. OR.; Nolan, S. K.

2001-01-01

A new method for determining unfiltered shortwave (SW), longwave (LW) and window (W) radiances from filtered radiances measured by the Clouds and the Earth's Radiant Energy System (CERES) satellite instrument is presented. The method uses theoretically derived regression coefficients between filtered and unfiltered radiances that are a function of viewing geometry, geotype and whether or not cloud is present. Relative errors in insta.ntaneous unfiltered radiances from this method are generally well below 1% for SW radiances (approx. 0.4% 1(sigma) or approx.l W/sq m equivalent flux), < 0.2% for LW radiances (approx. 0.1% 1(sigma) or approx.0.3 W/sq m equivalent flux) and < 0.2% (approx. 0.1% 1(sigma) for window channel radiances.

T(sub lambda) Depression by a Heat Current Along the lambda-Line

NASA Technical Reports Server (NTRS)

Liu, Yuanming; Larson, Melora; Iraelsson, Ulf E.

1999-01-01

We report measurements of the depression of the superfluid transition temperature by a heat current (1 less than or = Q less than or = 100 microW/sq cm) along the lambda-line (SVP less than or = P less than or = 21.6 bar). At P = 21.6 bar, measurements were also performed in a reduced gravity (0.2g). Experimental results show that the pressure dependence of the depression and the gravity effect on the measurements are small, in qualitative agreement with theoretical predictions. Keywords: superfluid helium; Lambda transition; heat current

Testing an Algae-Based Air-Regeneration System

NASA Technical Reports Server (NTRS)

Nienow, James

1998-01-01

The potential of an air-regeneration system based on the growth of unicellular algae on the surface of porous ceramic tubes was evaluated. The system is fairly robust with respect to environmental conditions and is capable of maintaining algal cultures for up to 365 days. Under standard conditions (50-66 micro mol/sq mm s (PPF), 450 micro mol mol of CO2), mature tubes can remove CO2 at a rate of up to 90 micro mol/sq m min. Under these conditions, approximately 200 square meters of area would be required for each member of the crew. However, the rate of uptake increases with both photon flux and CO2 concentration in accordance with Michaelis-Menton dynamics. An extrapolation to conditions of saturating light and carbon dioxide indicates that the area required can be reduced by a factor of at least 2.5.

Deployment loads data from a free-flight investigation of all flexible parawings having 371.612 sq meters (4000 sq feet) of wing area

NASA Technical Reports Server (NTRS)

Croom, D. R.

1971-01-01

A free-flight test program to determine the deployment characteristics of all-flexible parawings was conducted. Both single-keel and twin-keel parawings having a wing area of 4000 square feet with a five-stage reefing system were tested by use of a bomb-type instrumented test vehicle. Several twin-keel-parawing tests were also made by using an instrumented controllable sled-type test vehicle. The systems were launched from either a C-130 or a C-119 carrier airplane, and a programer parachute was used to bring the test vehicle to a proper dynamic pressure and near-vertical flight path prior to deployment of the parawing system. The free-flight deployment loads data are presented in the form of time histories of individual suspension-line loads and total loads.

Clinical benefits of treatment with SQ house dust mite sublingual tablet in house dust mite allergic rhinitis.

PubMed

Demoly, P; Kleine-Tebbe, J; Rehm, D

2017-10-01

Treatment with SQ (standardised quality) house dust mite sublingual tablet for 1 year resulted in a decreased probability of having an allergic rhinitis (AR) exacerbation day (from 11% [placebo] to 5% [SQ house dust mite sublingual tablet]) and an increased probability of having a mild AR day (from 16% [placebo] to 34% [SQ house dust mite sublingual tablet]). © 2017 EAACI and John Wiley and Sons A/S. Published by John Wiley and Sons Ltd.

Design and evaluation of thermodynamic vent/screen baffle cryogenic storage system. [for space shuttles, space tugs, and spacelab

NASA Technical Reports Server (NTRS)

Cady, E. C.

1975-01-01

A comprehensive analytical program was performed to compare an integrated thermodynamic vent/screen baffle orbital cryogenic propellant storage and transfer system with other concepts. The screen systems were found to be 20% to 29% lighter in weight than a propulsively accelerated Tug-scale LH2/LO2 resupply module. The screen systems were compared with small-scale supercritical storage systems for the space shuttle fuel cell reactant and life support system fluid supply and were lighter by up to 556 kg (1225 lb) for the extended 30-day mission. When compared with high-pressure gas storage for the spacelab atmosphere supply, the screen system saved 79% of the inert system weight for the 30-day mission. An experimental program found that heat flux rates up to 9,450 watts/sq m (3,000 Btu/hr-sq ft) degraded the LH2 bubble point performance of eight screens by a maximum of 12.5%. No effects of helium pressurant, screen material, or LH2 superheat were observed.

Performance of alumina-supported Pt catalysts in an electron-beam-sustained CO2 laser amplifier

NASA Technical Reports Server (NTRS)

Cunningham, D. L.; Jones, P. L.; Miyake, C. I.; Moody, S. E.

1990-01-01

The performance of an alumina-supported Pt catalyst system used to maintain the gas purity in an electron-beam-sustained (636) isotope CO2 laser amplifier has been tested. The system characteristics using the two-zone, parallel flow reactor were determined for both continuous- and end-of-day reactor operation using on-line mass spectrometric sampling. The laser amplifier was run with an energy loading of typically 110 J-l/atm and an electron-beam current of 4 mA/sq cm. With these conditions and a pulse repetition frequency of 10 Hz for up to 10,000 shots, increases on the order of 100 ppm O2 were observed with the purifier on and 150 ppm with it off. The 1/e time recovery time was found to be approximately 75 minutes.

The association between sleep quality, low back pain and disability: A prospective study in routine practice.

PubMed

Kovacs, F M; Seco, J; Royuela, A; Betegon, J N; Sánchez-Herráez, S; Meli, M; Martínez Rodríguez, M E; Núñez, M; Álvarez-Galovich, L; Moyá, J; Sánchez, C; Luna, S; Borrego, P; Moix, J; Rodríguez-Pérez, V; Torres-Unda, J; Burgos-Alonso, N; Gago-Fernández, I; González-Rubio, Y; Abraira, V

2018-01-01

The objective of this study was to estimate the association between sleep quality (SQ) and improvements in low back pain (LBP) and disability, among patients treated for LBP in routine practice. This prospective cohort study included 461 subacute and chronic LBP patients treated in 11 specialized centres, 14 primary care centres and eight physical therapy practices across 12 Spanish regions. LBP, leg pain, disability, catastrophizing, depression and SQ were assessed through validated questionnaires upon recruitment and 3 months later. Logistic regression models were developed to assess: (1) the association between the baseline score for SQ and improvements in LBP and disability at 3 months, and (2) the association between improvement in SQ and improvements in LBP and disability during the follow-up period. Seventy-three per cent of patients were subacute. Median scores at baseline were four points for both pain and disability, as assessed with a visual analog scale and the Roland-Morris Questionnaire, respectively. Regression models showed (OR [95% CI]) that baseline SQ was not associated with improvements in LBP (0.99 [0.94; 1.06]) or in disability (0.99 [0.93; 1.05]), although associations existed between 'improvement in SQ' and 'improvement in LBP' (4.34 [2.21; 8.51]), and 'improvement in SQ' and 'improvement in disability' (4.60 [2.29; 9.27]). Improvement in SQ is associated with improvements in LBP and in disability at 3-month follow-up, suggesting that they may reflect or be influenced by common factors. However, baseline SQ does not predict improvements in pain or disability. In clinical practice, sleep quality, low back pain and disability are associated. However, sleep quality at baseline does not predict improvement in pain and disability. © 2017 European Pain Federation - EFIC®.

Development of a questionnaire to measure consumers' perceptions of service quality in Australian community pharmacies.

PubMed

Mirzaei, Ardalan; Carter, Stephen R; Chen, Jenny Yimin; Rittsteuer, Claudia; Schneider, Carl R

2018-06-11

Recent changes within community pharmacy have seen a shift towards some pharmacies providing "value-added" services. However, providing high levels of service is resource intensive yet revenues from dispensing are declining. Of significance therefore, is how consumers perceive service quality (SQ). However, at present there are no validated and reliable instruments to measure consumers' perceptions of SQ in Australian community pharmacies. The aim of this study was to build a theory-grounded model of service quality (SQ) in community pharmacies and to create a valid survey instrument to measure consumers' perceptions of service quality. Stage 1 dealt with item generation using theory, prior research and qualitative interviews with pharmacy consumers. Selected items were then subjected to content validity and face validity. Stages 2 and 3 included psychometric testing among English-speaking adult consumers of Australian pharmacies. Exploratory factor analysis was used for item reduction and to explain the domains of SQ. In stage 1, item generation for SQ initially generated 113 items which were then refined, through content and face validity, down to 61 items. In stage 2, after subjecting the questionnaire to psychometric testing on the data from the first pharmacy (n = 374), the use of the primary dimensions of SQ was abandoned leaving 32 items representing 5 domains of SQ. In stage 3, the questionnaire was subject to further testing and item reduction in 3 other pharmacies (n = 320). SQ was best described using 23 items representing 6 domains: 'health and medicines advice', 'relationship quality', 'technical quality', 'environmental quality', 'non-prescription service', and 'health outcomes'. This research presents a theoretically-grounded and robust measurement scale developed for consumer perceptions of SQ in a community pharmacy. Copyright © 2018. Published by Elsevier Inc.

Voltage and power relationships in lithium-containing solar cells.

NASA Technical Reports Server (NTRS)

Faith, T. J.

1972-01-01

Photovoltaic characteristics have been measured on a large number of crucible-grown lithium-containing solar cells irradiated by 1-MeV electrons to fluences ranging from 3 x 10 to the 13th power to 3 x 10 to the 15th power electrons per sq cm. These measurements have established empirical relationships between cell photovoltaic parameters and lithium donor density gradient. Short-circuit current and maximum power measured immediately after irradiation decrease logarithmically with lithium gradient. Open-circuit voltage increases logarithmically with lithium gradient both immediately after irradiation and after recovery, the degree of recovery being strongly gradient-dependent at high fluence. As a result, the maximum power and the power at 0.43 V after recovery from 3 x 10 to the 15th power electrons per sq cm increase with increasing lithium gradient.

Development of gas-phase metallized plaques for electrodes of storage batteries, in particular for nickel oxide electrodes

NASA Astrophysics Data System (ADS)

Linkohr, R.; Schladitz, H.

1982-08-01

Nickel oxide-electrode plaques for alkaline batteries have been developed by carbon vapor deposition plating fiber plaque substrates with nickel from nickelcarbonyo. Carbon felt proved to be a suitable substrate and large (22 x sq 15 sq cm) and thick 3 - 5 mm) plaques could be made from this material. Three metallization devices were constructed, one of which allowed continuous processing with carbonyl gas flowing through the felt; this improved evenness of nickel distribution. The physical properties of the plaques - structure, electric resistance, heat conduction, gas permeation - approximated by simple models and the corresponding calculations were compared with measurements. Nickel oxide electrodes were made from the plaques and were cycled in half-cell arrangements. The project goals concerning nickel sayings, capacity per unit area and current capability were reached.

The LDEF ultra heavy cosmic ray experiment

NASA Technical Reports Server (NTRS)

Osullivan, D.; Thompson, A.; Bosch, J.; Keegan, R.; Wenzel, K.-P.; Smit, A.; Domingo, C.

1991-01-01

The Long Duration Exposure Facility (LDEF) Ultra Heavy Cosmic Ray Experiment (UHCRE) used 16 side viewing LDEF trays giving a total geometry factor for high energy cosmic rays of 30 sq m sr. The total exposure factor was 170 sq m sr y. The experiment is based on a modular array of 192 solid state nuclear track detector stacks, mounted in sets of 4 pressure vessels (3 experiment tray). The extended duration of the LDEF mission has resulted in a greatly enhanced potential scientific yield from the UHCRE. Initial scanning results indicate that at least 2000 cosmic ray nuclei with Z greater than 65 were collected, including the world's first statistically significant sample of actinides. Postflight work to date and the current status of the experiment are reviewed. Provisional results from analysis of preflight and postflight calibrations are presented.

Integrated Vertical Bloch Line (VBL) memory

NASA Technical Reports Server (NTRS)

Katti, R. R.; Wu, J. C.; Stadler, H. L.

1991-01-01

Vertical Bloch Line (VBL) Memory is a recently conceived, integrated, solid state, block access, VLSI memory which offers the potential of 1 Gbit/sq cm areal storage density, data rates of hundreds of megabits/sec, and submillisecond average access time simultaneously at relatively low mass, volume, and power values when compared to alternative technologies. VBLs are micromagnetic structures within magnetic domain walls which can be manipulated using magnetic fields from integrated conductors. The presence or absence of BVL pairs are used to store binary information. At present, efforts are being directed at developing a single chip memory using 25 Mbit/sq cm technology in magnetic garnet material which integrates, at a single operating point, the writing, storage, reading, and amplification functions needed in a memory. The current design architecture, functional elements, and supercomputer simulation results are described which are used to assist the design process.

Trends of Measured Climate Forcing Agents

NASA Technical Reports Server (NTRS)

Hansen, James E.; Sato, Makiko; Einaudi, Franco (Technical Monitor)

2002-01-01

The growth rate of climate forcing by measured greenhouse gases peaked near 1980 at almost 5 W/sq m per century. This growth rate has since declined to approximately equal to 3 W/sq m per century, largely because of cooperative international actions. We argue that trends can be reduced to the level needed for the moderate "alternative" climate scenario (approximately equal to 2 W/M2 per century for the next 50 years) by means of concerted actions that have other benefits, but the forcing reductions are not automatic "co-benefits" of actions that slow CO2 emissions. Current trends of climate forcings by aerosols remain very uncertain. Nevertheless, practical constraints on changes in emission levels suggest that global warming at a rate + 0.15 +/- 0.05 C per decade will occur over the next several decades.

A summary of results from solar monitoring rocket flights

NASA Technical Reports Server (NTRS)

Duncan, C. H.

1981-01-01

Three rocket flights to measure the solar constant and provide calibration data for sensors aboard Nimbus 6, 7, and Solar Maximum Mission (SMM) spacecraft were accomplished. The values obtained by the rocket instruments for the solar constant in SI units are: 1367 w/sq m on 29 June 1976; 1372 w/sq m on 16 November 1978; and 1374 w/sq m on 22 May 1980. The uncertainty of the rocket measurements is + or - 0.5%. The values obtained by the Hickey-Frieden sensor on Nimbus 7 during the second and third flights was 1376 w/sq m. The value obtained by the Active Cavity Radiometer Model IV (ACR IV) on SMM during the flight was 1368 w/sq m.

Stability of Silica- and Enzyme-Treated Palm Oil Under Deep Frying Conditions.

PubMed

Karim, Nur Azwani Ab; Noor, Ahmadilfitri Md; Lee, Yee-Ying; Lai, Oi-Ming

2015-12-01

The oxidative and thermal stability of low diglycerides palm oil produced via silica treatment (sPO) and enzymatic treatment (ePO) compared with standard quality palm oil (SQ) and premium quality palm oil (PQ) was investigated. Both of the oils displayed better oxidative stability compared with SQ as well as significantly higher (P < 0.05) thermal resistance and oxidative strength than SQ and PQ due to lower amounts of partial glycerides. Although the initial induction periods (IPs) of sPO and ePO were significantly lower compared with SQ and PQ, both the oils showed slower drops in their IP values. The darkening effect after frying was significantly (P < 0.05) slower in sPO compared with SQ, PQ, and ePO. Besides, there is no difference p > 0.05 in the rate of FFA formation between sPO and PQ. The anisidine value and peroxide values were lowest in sPO, followed by ePO, PQ, and SQ. © 2015 Institute of Food Technologists®

IS Success Model in E-Learning Context Based on Students' Perceptions

ERIC Educational Resources Information Center

Freeze, Ronald D.; Alshare, Khaled A.; Lane, Peggy L.; Wen, H. Joseph

2010-01-01

This study utilized the Information Systems Success (ISS) model in examining e-learning systems success. The study was built on the premise that system quality (SQ) and information quality (IQ) influence system use and user satisfaction, which in turn impact system success. A structural equation model (SEM), using LISREL, was used to test the…

Building a sense of virtual community: the role of the features of social networking sites.

PubMed

Chen, Chi-Wen; Lin, Chiun-Sin

2014-07-01

In recent years, social networking sites have received increased attention because of the potential of this medium to transform business by building virtual communities. However, theoretical and empirical studies investigating how specific features of social networking sites contribute to building a sense of virtual community (SOVC)-an important dimension of a successful virtual community-are rare. Furthermore, SOVC scales have been developed, and research on this issue has been called for, but few studies have heeded this call. On the basis of prior literature, this study proposes that perceptions of the three most salient features of social networking sites-system quality (SQ), information quality (IQ), and social information exchange (SIE)-play a key role in fostering SOVC. In particular, SQ is proposed to increase IQ and SIE, and SIE is proposed to enhance IQ, both of which thereafter build SOVC. The research model was examined in the context of Facebook, one of the most popular social networking sites in the world. We adopted Blanchard's scales to measure SOVC. Data gathered using a Web-based questionnaire, and analyzed with partial least squares, were utilized to test the model. The results demonstrate that SIE, SQ, and IQ are the factors that form SOVC. The findings also suggest that SQ plays a fundamental role in supporting SIE and IQ in social networking sites. Implications for theory, practice, and future research directions are discussed.

Brain Type or Sex Differences? A structural equation model of the relation between brain type, sex, and motivation to learn science

NASA Astrophysics Data System (ADS)

Zeyer, Albert; Bölsterli, Katrin; Brovelli, Dorothee; Odermatt, Freia

2012-03-01

Sex is considered to be one of the most significant factors influencing attitudes towards science. However, the so-called brain type approach from cognitive science suggests that the difference in motivation to learn science does not primarily differentiate the girls from the boys, but rather the so-called systemisers from the empathizers. The present study investigates this hypothesis by using structural equation modelling on a sex-stratified sample of 500 male and female students of secondary II level. The results show, that the motivation to learn science is directly influenced by the systemizing quotient SQ, but not by sex. The impact of sex on the motivation to learn science, measured by five key concepts, only works indirectly, namely through the influence of sex on the SQ. The empathizing quotient (EQ) has no impact on the motivation to learn science. The SQ explains between 13 and 23 percent of the variation of the five key constructs. In female students, the impact of the SQ is very similar for all key concepts. In male students, it is highest for self-efficacy and lowest for assessment anxiety. The motivation to learn science is significantly larger for male students in all involved SMQ key concepts, but the difference is small. The interpretation of these findings and conclusions for science teaching and further research are discussed.

Growth and characterization of high current density, high-speed InAs/AlSb resonant tunneling diodes

NASA Technical Reports Server (NTRS)

Soderstrom, J. R.; Brown, E. R.; Parker, C. D.; Mahoney, L. J.; Yao, J. Y.

1991-01-01

InAs/AlSb double-barrier resonant tunneling diodes with peak current densities up to 370,000 A/sq cm and high peak-to-valley current ratios of 3.2 at room temperature have been fabricated. The peak current density is well-explained by a stationary-state transport model with the two-band envelope function approximation. The valley current density predicted by this model is less than the experimental value by a factor that is typical of the discrepancy found in other double-barrier structures. It is concluded that threading dislocations are largely inactive in the resonant tunneling process.

Estimates of galactic cosmic ray shielding requirements during solar minimum

NASA Technical Reports Server (NTRS)

Townsend, Lawrence W.; Nealy, John E.; Wilson, John W.; Simonsen, Lisa C.

1990-01-01

Estimates of radiation risk from galactic cosmic rays are presented for manned interplanetary missions. The calculations use the Naval Research Laboratory cosmic ray spectrum model as input into the Langley Research Center galactic cosmic ray transport code. This transport code, which transports both heavy ions and nucleons, can be used with any number of layers of target material, consisting of up to five different arbitrary constituents per layer. Calculated galactic cosmic ray fluxes, dose and dose equivalents behind various thicknesses of aluminum, water and liquid hydrogen shielding are presented for the solar minimum period. Estimates of risk to the skin and the blood-forming organs (BFO) are made using 0-cm and 5-cm depth dose/dose equivalent values, respectively, for water. These results indicate that at least 3.5 g/sq cm (3.5 cm) of water, or 6.5 g/sq cm (2.4 cm) of aluminum, or 1.0 g/sq cm (14 cm) of liquid hydrogen shielding is required to reduce the annual exposure below the currently recommended BFO limit of 0.5 Sv. Because of large uncertainties in fragmentation parameters and the input cosmic ray spectrum, these exposure estimates may be uncertain by as much as a factor of 2 or more. The effects of these potential exposure uncertainties or shield thickness requirements are analyzed.

Stability of bulk Ba2YCu3O(7-x) in a variety of environments

NASA Technical Reports Server (NTRS)

Gaier, James R.; Hepp, Aloysius F.; Curtis, Henry B.; Schupp, Donald A.; Hambourger, Paul D.; Blue, James W.

1988-01-01

Small bars of ceramic Ba2YCu3O(7-x) were fabricated and subjected to environments similar to those that might be encountered during some NASA missions. These conditions include ambient conditions, high humidity, vacuum, and high fluences of electrons and protrons. The normal state resistivity or critical current density (J sub c) were monitored during these tests to assess the stability of the material. When normal state resistivity is used as a criterion, the ambient stability of these samples was relatively good, exhibiting only a 2 percent degradation over a 3 month period. The humidity stability was shown to be very poor, and to be a steep function of temperature. Samples stored at 50 C for 40 min increased in normal state resistivity by four orders of magnitude. Kinetic analysis indicates that the degradation reaction is second order with water vapor concentration. It is suspected that humidity degradation also accounts for the ambient instability. The samples were stable to vacuum over a period of at least 3 months. Degradation of J sub c in a 1 MeV electron fluence of 9.7 x 10 to the 14th e(-)/sq cm was determined to be no more than about 2 percent. Degradation of J sub c in a 8.7 x 10 to the 14th p(+)/sq cm of 42 MeV protons was found to be grain size dependent. Samples with smaller grain size and initial J sub c of about 240 A/sq cm showed no degradation. while that with larger grain size and an initial J sub c of about 30 A/sq cm degraded to 37 percent of its original value.

Reliable Entity Subtyping in Non-small Cell Lung Cancer by Matrix-assisted Laser Desorption/Ionization Imaging Mass Spectrometry on Formalin-fixed Paraffin-embedded Tissue Specimens*

PubMed Central

Kriegsmann, Mark; Casadonte, Rita; Kriegsmann, Jörg; Dienemann, Hendrik; Schirmacher, Peter; Hendrik Kobarg, Jan; Schwamborn, Kristina; Stenzinger, Albrecht; Warth, Arne; Weichert, Wilko

2016-01-01

Histopathological subtyping of non-small cell lung cancer (NSCLC) into adenocarcinoma (ADC), and squamous cell carcinoma (SqCC) is of utmost relevance for treatment stratification. However, current immunohistochemistry (IHC) based typing approaches on biopsies are imperfect, therefore novel analytical methods for reliable subtyping are needed. We analyzed formalin-fixed paraffin-embedded tissue cores of NSCLC by Matrix-assisted laser desorption/ionization (MALDI) imaging on tissue microarrays to identify and validate discriminating MALDI imaging profiles for NSCLC subtyping. 110 ADC and 98 SqCC were used to train a Linear Discriminant Analysis (LDA) model. Results were validated on a separate set of 58 ADC and 60 SqCC. Selected differentially expressed proteins were identified by tandem mass spectrometry and validated by IHC. The LDA classification model incorporated 339 m/z values. In the validation cohort, in 117 cases (99.1%) MALDI classification on tissue cores was in accordance with the pathological diagnosis made on resection specimen. Overall, three cases in the combined cohorts were discordant, after reevaluation two were initially misclassified by pathology whereas one was classified incorrectly by MALDI. Identification of differentially expressed peptides detected well-known IHC discriminators (CK5, CK7), but also less well known differentially expressed proteins (CK15, HSP27). In conclusion, MALDI imaging on NSCLC tissue cores as small biopsy equivalents is capable to discriminate lung ADC and SqCC with a very high accuracy. In addition, replacing multislide IHC by an one-slide MALDI approach may also save tissue for subsequent predictive molecular testing. We therefore advocate to pursue routine diagnostic implementation strategies for MALDI imaging in solid tumor typing. PMID:27473201

Reliable Entity Subtyping in Non-small Cell Lung Cancer by Matrix-assisted Laser Desorption/Ionization Imaging Mass Spectrometry on Formalin-fixed Paraffin-embedded Tissue Specimens.

PubMed

Kriegsmann, Mark; Casadonte, Rita; Kriegsmann, Jörg; Dienemann, Hendrik; Schirmacher, Peter; Hendrik Kobarg, Jan; Schwamborn, Kristina; Stenzinger, Albrecht; Warth, Arne; Weichert, Wilko

2016-10-01

Histopathological subtyping of non-small cell lung cancer (NSCLC) into adenocarcinoma (ADC), and squamous cell carcinoma (SqCC) is of utmost relevance for treatment stratification. However, current immunohistochemistry (IHC) based typing approaches on biopsies are imperfect, therefore novel analytical methods for reliable subtyping are needed. We analyzed formalin-fixed paraffin-embedded tissue cores of NSCLC by Matrix-assisted laser desorption/ionization (MALDI) imaging on tissue microarrays to identify and validate discriminating MALDI imaging profiles for NSCLC subtyping. 110 ADC and 98 SqCC were used to train a Linear Discriminant Analysis (LDA) model. Results were validated on a separate set of 58 ADC and 60 SqCC. Selected differentially expressed proteins were identified by tandem mass spectrometry and validated by IHC. The LDA classification model incorporated 339 m/z values. In the validation cohort, in 117 cases (99.1%) MALDI classification on tissue cores was in accordance with the pathological diagnosis made on resection specimen. Overall, three cases in the combined cohorts were discordant, after reevaluation two were initially misclassified by pathology whereas one was classified incorrectly by MALDI. Identification of differentially expressed peptides detected well-known IHC discriminators (CK5, CK7), but also less well known differentially expressed proteins (CK15, HSP27). In conclusion, MALDI imaging on NSCLC tissue cores as small biopsy equivalents is capable to discriminate lung ADC and SqCC with a very high accuracy. In addition, replacing multislide IHC by an one-slide MALDI approach may also save tissue for subsequent predictive molecular testing. We therefore advocate to pursue routine diagnostic implementation strategies for MALDI imaging in solid tumor typing. © 2016 by The American Society for Biochemistry and Molecular Biology, Inc.

The Global Character of the Flux of Downward Longwave Radiation

NASA Technical Reports Server (NTRS)

Stephens, Graeme L.; Wild, Martin; Stackhouse, Paul W., Jr.; L'Ecuyer, Tristan; Kato, Seiji; Henderson, David S.

2012-01-01

Four different types of estimates of the surface downwelling longwave radiative flux (DLR) are reviewed. One group of estimates synthesizes global cloud, aerosol, and other information in a radiation model that is used to calculate fluxes. Because these synthesis fluxes have been assessed against observations, the global-mean values of these fluxes are deemed to be the most credible of the four different categories reviewed. The global, annual mean DLR lies between approximately 344 and 350 W/sq m with an error of approximately +/-10 W/sq m that arises mostly from the uncertainty in atmospheric state that governs the estimation of the clear-sky emission. The authors conclude that the DLR derived from global climate models are biased low by approximately 10 W/sq m and even larger differences are found with respect to reanalysis climate data. The DLR inferred from a surface energy balance closure is also substantially smaller that the range found from synthesis products suggesting that current depictions of surface energy balance also require revision. The effect of clouds on the DLR, largely facilitated by the new cloud base information from the CloudSat radar, is estimated to lie in the range from 24 to 34 W/sq m for the global cloud radiative effect (all-sky minus clear-sky DLR). This effect is strongly modulated by the underlying water vapor that gives rise to a maximum sensitivity of the DLR to cloud occurring in the colder drier regions of the planet. The bottom of atmosphere (BOA) cloud effect directly contrast the effect of clouds on the top of atmosphere (TOA) fluxes that is maximum in regions of deepest and coldest clouds in the moist tropics.

The Ability of Patient-Symptom Questionnaires to Differentiate PVFMD From Asthma.

PubMed

Ye, Jinny; Nouraie, Mehdi; Holguin, Fernando; Gillespie, Amanda I

2017-05-01

Goals of the current study were to (1) conduct initial validation of a new Paradoxical Vocal Fold Movement Disorder Screening Questionnaire (PVFMD-SQ); (2) determine if symptom-based questionnaires can discriminate between patients with confirmed PVFMD and those with diagnosed uncontrolled asthma without clinical suspicion for PVFMD; and (3) determine if a new questionnaire with diagnostic specificity could be created from a combination of significant items on previously validated questionnaires. This is a prospective, case-controlled study of patients with PVFMD only and asthma only, who completed five questionnaires: Dyspnea Index, Reflux Symptom Index, Voice Handicap Index-10, Sino-Nasal Questionnaire, and PVFMD-SQ. Factor analysis was completed on the new PVFMD-SQ, and the discrimination ability of selected factors was assessed by receiver operating characteristics curve. The factor with the greatest discriminatory ability was selected to create one diagnostic questionnaire, and scores for each participant were calculated to estimate how well the factor correlated with a PVFMD or asthma diagnosis. Mean scores on all questionnaires were compared to test their discriminatory ability. Patients with PVFMD showed greater voice handicap and reflux symptoms than patients with asthma. A 15-item one-factor questionnaire was developed from the original PVFMD-SQ, with a sensitivity of 89% and specificity of 73% for diagnosing asthma versus PVFMD. The combined questionnaires resulted in four factors, none of which showed discriminatory ability between PVFMD and asthma. This study represents the first time that a patient symptom-based screening tool has shown diagnostic sensitivity to differentiate PVFMD from asthma in a cohort of symptomatic patients. Copyright © 2017 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Local versus offshore production of ready-to-use therapeutic foods and small quantity lipid-based nutrient supplements.

PubMed

Segrè, Joel; Liu, Grace; Komrska, Jan

2017-10-01

Manufacturers on four continents currently produce ready-to-use therapeutic foods (RUTF). Some produce locally, near their intended users, while others produce offshore and ship their product long distances. Small quantity lipid-based nutrient supplements (SQ-LNS) such as Nutriset's Enov'Nutributter are not yet in widespread production. There has been speculation whether RUTF and SQ-LNS should be produced primarily offshore, locally, or both. We analyzed The United Nations Children's Fund (UNICEF) Supply Division data, reviewed published literature, and interviewed local manufacturers to identify key benefits and challenges to local versus offshore manufacture of RUTF. Both prices and estimated costs for locally produced product have consistently been higher than offshore prices. Local manufacture faces challenges in taxation on imported ingredients, low factory utilization, high interest rates, long cash conversion cycle, and less convenient access to quality testing labs. Benefits to local economies are not likely to be significant. Although offshore manufacturers offer RUTF at lower cost, local production is getting closer to cost parity for RUTF. UNICEF, which buys the majority of RUTF globally, continues to support local production, and efforts are underway to narrow the cost gap further. Expansion of RUTF producers into the production of other ready-to-use foods, including SQ-LNS in order to reach a larger market and achieve a more sustainable scale, may further close the cost and price gap. Local production of both RUTF and SQ-LNS could be encouraged by a favorable tax environment, assistance in lending, consistent forecasts from buyers, investment in reliable input supply chains, and local laboratory testing. © 2016 John Wiley & Sons Ltd.

Advancing Solar Irradiance Measurement for Climate-Related Studies: Accurate Constraint on Direct Aerosol Radiative Effect (DARE)

NASA Technical Reports Server (NTRS)

Tsay, Si-Chee; Ji, Q. Jack

2011-01-01

Earth's climate is driven primarily by solar radiation. As summarized in various IPCC reports, the global average of radiative forcing for different agents and mechanisms, such as aerosols or CO2 doubling, is in the range of a few W/sq m. However, when solar irradiance is measured by broadband radiometers, such as the fleet of Eppley Precision Solar Pyranometers (PSP) and equivalent instrumentation employed worldwide, the measurement uncertainty is larger than 2% (e.g., WMO specification of pyranometer, 2008). Thus, out of the approx. 184 W/sq m (approx.263 W/sq m if cloud-free) surface solar insolation (Trenberth et al. 2009), the measurement uncertainty is greater than +/-3.6 W/sq m, overwhelming the climate change signals. To discern these signals, less than a 1 % measurement uncertainty is required and is currently achievable only by means of a newly developed methodology employing a modified PSP-like pyranometer and an updated calibration equation to account for its thermal effects (li and Tsay, 2010). In this talk, we will show that some auxiliary measurements, such as those from a collocated pyrgeometer or air temperature sensors, can help correct historical datasets. Additionally, we will also demonstrate that a pyrheliometer is not free of the thermal effect; therefore, comparing to a high cost yet still not thermal-effect-free "direct + diffuse" approach in measuring surface solar irradiance, our new method is more economical, and more likely to be suitable for correcting a wide variety of historical datasets. Modeling simulations will be presented that a corrected solar irradiance measurement has a significant impact on aerosol forcing, and thus plays an important role in climate studies.

Willingness to pay for small-quantity lipid-based nutrient supplements for women and children: Evidence from Ghana and Malawi.

PubMed

Adams, Katherine P; Vosti, Stephen A; Ayifah, Emmanuel; Phiri, Thokozani E; Adu-Afarwuah, Seth; Maleta, Kenneth; Ashorn, Ulla; Arimond, Mary; Dewey, Kathryn G

2018-04-01

Small-quantity lipid-based nutrient supplements (SQ-LNS) are designed to enrich maternal and child diets with the objective of preventing undernutrition during the first 1,000 days. Scaling up the delivery of supplements such as SQ-LNS hinges on understanding private demand and creatively leveraging policy-relevant factors that might influence demand. We used longitudinal stated willingness-to-pay (WTP) data from contingent valuation studies that were integrated into randomized controlled nutrition trials in Ghana and Malawi to estimate private valuation of SQ-LNS during pregnancy, postpartum, and early childhood. We found that average stated WTP for a day's supply of SQ-LNS was more than twice as high in Ghana than Malawi, indicating that demand for SQ-LNS (and by extension, the options for effective delivery of SQ-LNS) may be very context specific. We also examined factors associated with WTP, including intervention group, household socioeconomic status, birth outcomes, child growth, and maternal and child morbidity. In both sites, WTP was consistently negatively associated with household food insecurity, indicating that subsidization might be needed to permit food insecure households to acquire SQ-LNS if it is made available for purchase. In Ghana, WTP was higher among heads of household than among mothers, which may be related to control over household resources. Personal experience using SQ-LNS was not associated with WTP in either site. © 2017 The Authors. Maternal and Child Nutrition published by John Wiley & Sons, Ltd.

Strategies for soil quality assessment using VNIR gyperspectral spectroscopy in a western Kenya Chronosequence

USGS Publications Warehouse

Kinoshita, Rintaro; Moebius-Clune, Bianca N.; van Es, Harold M.; Hively, W. Dean; Bilgilis, A. Volkan

2012-01-01

Visible and near-infrared reflectance spectroscopy (VNIRS) is a rapid and nondestructive method that can predict multiple soil properties simultaneously, but its application in multidimensional soil quality (SQ) assessment in the tropics still needs to be further assessed. In this study, VNIRS (350–2500 nm) was employed to analyze 227 air-dried soil samples of Ultisols from a soil chronosequence in western Kenya and assess 16 SQ indicators. Partial least squares regression (PLSR) was validated using the full-site cross-validation method by grouping samples from each farm or forest site. Most suitable models successfully predicted SQ indicators (R2 ≥ 0.80; ratio of performance to deviation [RPD] ≥ 2.00) including soil organic matter (OMLOI), active C, Ca, cation exchange capacity (CEC), and clay. Moderately-well predicted indicators (0.50 ≤ R2 pwp), and field capacity (Θfc). Poorly predicted indicators (R2 < 0.50; RPD < 1.40) were EC, S, P, available water capacity (AWC), K, Zn, and penetration resistance. Combining VNIRS with selected field- and laboratory-measured SQ indicator values increased predictability. Furthermore, VNIRS showed moderate to substantial agreement in predicting interpretive SQ scores and a composite soil quality index (CSQI) especially when combined with directly measured SQ indicator values. In conclusion, VNIRS has good potential for low cost, rapid assessment of physical and biological SQ indicators but conventional soil chemical tests may need to be retained to provide comprehensive SQ assessments.

F2 layer characteristics and electrojet strength over an equatorial station

NASA Astrophysics Data System (ADS)

Adebesin, B. O.; Adeniyi, J. O.; Adimula, I. A.; Reinisch, B. W.; Yumoto, K.

2013-09-01

The data presented in this work describes the diurnal and seasonal variation in hmF2, NmF2, and the electrojet current strength over an African equatorial station during a period of low solar activity. The F2 region horizontal magnetic element H revealed that the Solar quiet Sq(H) daily variation rises from early morning period to maximum around local noon and falls to lower values towards evening. The F2 ionospheric current responsible for the magnetic field variations is inferred to build up at the early morning hours, attaining maximum strength around 1200 LT. The Sq variation across the entire months was higher during the daytime than nighttime. This is ascribed to the variability of the ionospheric parameters like conductivity and winds structure in this region. Seasonal daytime electrojet (EEJ) current strength for June solstice, March and September equinoxes, respectively had peak values ranging within 27-35 nT (at 1400 LT) , 30-40 nT (at 1200 LT) and 35-45 nT (at 1500 LT). The different peak periods of the EEJ strength were attributed to the combined effects of the peak electron density and electric field. Lastly, the EEJ strength was observed to be higher during the equinoxes than the solstice period.

[European Union Network for Patient Safety and Quality of Care (PASQ). Development and preliminary results in Europe and in the Spanish National Health System].

PubMed

Agra-Varela, Y; Fernández-Maíllo, M; Rivera-Ariza, S; Sáiz-Martínez-Acitorez, I; Casal-Gómez, J; Palanca-Sánchez, I; Bacou, J

2015-01-01

The joint action, European Union Network for Patient Safety and Quality of Care: PaSQ, aims to promote patient safety (PS) in the European Union (EU) and to facilitate the exchange of experiences among Member States (MS) and stakeholders on issues related to quality of care, PS, and patient involvement. The development and preliminary results are presented here, especially as regards the Spanish National Health System (SNHS). PaSQ is developed through 7 work packages, primarily aimed at sharing good practices (GP), which were identified using specific questionnaires and selected by means of explicit criteria, as well as to implement safe clinical practices (SCP) of proven effectiveness and agreed among MS. A total of 482 GP (39% provided by Spanish professionals) were identified. The 34 events organised in the EU, 11 including Spanish participation, facilitate sharing these practices. A total of 194 Health Care centres (49% in Spain) are implementing SCP (hand hygiene, safe surgery, medication reconciliation, and paediatric early warning scores) ACHIEVEMENTS AND FUTURE PERSPECTIVES: PaSQ is making it possible to strengthen collaboration between organizations and professionals at EU and SNHS level regarding PS and quality of care. Copyright © 2015 SECA. Published by Elsevier Espana. All rights reserved.

LiDAR observations of an Earth magmatic plumbing system as an analog for Venus and Mars distributed volcanism

NASA Astrophysics Data System (ADS)

Richardson, Jacob; Connor, Charles; Malservisi, Rocco; Bleacher, Jacob; Connor, Laura

2014-05-01

Clusters of tens to thousands of small volcanoes (diameters generally <30 km) are common features on the surface of Mars, Venus, and the Earth. These clusters may be described as distributed-style volcanism. Better characterizing the magmatic plumbing system of these clusters can constrain magma ascent processes as well as the regional magma production budget and heat flux beneath each cluster. Unfortunately, directly observing the plumbing systems of volcano clusters on Mars and Venus eludes our current geologic abilities. Because erosion exposes such systems at the Earth's surface, a better understanding of magmatic processes and migration can be achieved via field analysis. The terrestrial plumbing system of an eroded volcanic field may be a valuable planetary analog for Venus and Mars clusters. The magmatic plumbing system of a Pliocene-aged monogenetic volcanic field, emplaced at 0.8 km depth, is currently exposed as a sill and dike swarm in the San Rafael Desert of Central Utah, USA. The mafic bodies in this region intruded into Mesozoic sedimentary units and now make up the most erosion resistant units as sills, dikes, and plug-like conduits. Light Detection and Ranging (LiDAR) can identify volcanic units (sills, dikes, and conduits) at high resolution, both geomorphologically and with near infrared return intensity values. Two Terrestrial LiDAR Surveys and an Airborne LiDAR Survey have been carried out over the San Rafael volcanic swarm, producing a three dimensional point cloud over approximately 36 sq. km. From the point clouds of these surveys, 1-meter DEMs are produced and volcanic intrusions have been mapped. Here we present reconstructions of the volcanic instrusions of the San Rafael Swarm. We create this reconstruction by extrapolating mapped intrustions from the LiDAR surveys into a 3D space around the current surface. We compare the estimated intrusive volume to the estimated conduit density and estimates of extrusive volume at volcano clusters of similar density. The extrapolated reconstruction and conduit mapping provide a first-order estimate of the final intrustive/extrusive volume ratio for the now eroded volcanic field. Earth, Venus and Mars clusters are compared using Kernel Density Estimation (KDE) , which objectively compares cluster area, complexity, and vent density per sq. km. We show that Martian clusters are less dense than Venus clusters, which in turn are less dense than those on Earth. KDE and previous models of intrusive morphology for Mars and Venus are here used to calibrate the San Rafael plumbing system model to clusters on the two planets. The results from the calibrated Mars and Venus plumbing system models can be compared to previous estimates of magma budget and intrusive/extrusive ratios on Venus and Mars.

Evaluation of low cost/high temperature insulation, July 1974 - June 1975

NASA Technical Reports Server (NTRS)

Strauss, E. L.

1975-01-01

Six fiber products and six insulation blankets comprising silica, alumina, zirconia, mullite, and mixed ceramic systems were subjected to furnace exposures up to 500 hours at temperatures of 1000 to 1600 C and evaluated for chemical and dimensional stability and for changes in thermal conductivity. Alumina, zirconia, and mullite fibers were fabricated into reusable surface insulation (RSI) tile by water-felting and reimpregnation with ethyl silicate. Specimens were exposed to 25 thermal cycles at 1200 C and 1400 C and a pressure of 10 and 32 torr, respectively. Production costs for 930 sq m (10,000 sq ft) of blanket insulation and of alumina RSI tile were developed.

Development of LOX/LH2 tank system for H-I launch vehicle

NASA Astrophysics Data System (ADS)

Nozaki, Y.; Takamatsu, H.; Morino, Y.; Imagawa, K.

Design features of the second stage of the prospective Japanese H-1 launch vehicle are described. The stage will use an LO2/LH2 fueled engine. The fuels will be contained in a 2219 Al alloy tank insulated with sprayed polyurethane foam. The total stage length will be 5.5 m, the volume 6.8 m, pressure 3.2 kg/sq cm (LOX) and 2.5 kg/sq cm (LH2). The diameter is 2.5 m and total fuel mass is 8.7 tons. Design verification tests, consisting of burning tests and thermal evaluation, are scheduled for the near future.

The Triton: Design concepts and methods

NASA Technical Reports Server (NTRS)

Meholic, Greg; Singer, Michael; Vanryn, Percy; Brown, Rhonda; Tella, Gustavo; Harvey, Bob

1992-01-01

During the design of the C & P Aerospace Triton, a few problems were encountered that necessitated changes in the configuration. After the initial concept phase, the aspect ratio was increased from 7 to 7.6 to produce a greater lift to drag ratio (L/D = 13) which satisfied the horsepower requirements (118 hp using the Lycoming O-235 engine). The initial concept had a wing planform area of 134 sq. ft. Detailed wing sizing analysis enlarged the planform area to 150 sq. ft., without changing its layout or location. The most significant changes, however, were made just prior to inboard profile design. The fuselage external diameter was reduced from 54 to 50 inches to reduce drag to meet the desired cruise speed of 120 knots. Also, the nose was extended 6 inches to accommodate landing gear placement. Without the extension, the nosewheel received an unacceptable percentage (25 percent) of the landing weight. The final change in the configuration was made in accordance with the stability and control analysis. In order to reduce the static margin from 20 to 13 percent, the horizontal tail area was reduced from 32.02 to 25.0 sq. ft. The Triton meets all the specifications set forth in the design criteria. If time permitted another iteration of the calculations, two significant changes would be made. The vertical stabilizer area would be reduced to decrease the aircraft lateral stability slope since the current value was too high in relation to the directional stability slope. Also, the aileron size would be decreased to reduce the roll rate below the current 106 deg/second. Doing so would allow greater flap area (increasing CL(sub max)) and thus reduce the overall wing area. C & P would also recalculate the horsepower and drag values to further validate the 120 knot cruising speed.

The SQ3R Study Technique Enhances Comprehension of an Introductory Psychology Textbook.

ERIC Educational Resources Information Center

Chastain, Garvin; Thurber, Steven

1989-01-01

Examines the effectiveness of the SQ3R study technique in enhancing comprehension of material in an introductory psychology textbook. Finds significantly better performance on tests of recall or conceptual items for students using SQ3R than for those using individual study methods. (RS)

76 FR 62434 - Federal Property Suitable as Facilities To Assist the Homeless

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-07

... asbestos/PCBs Former SSA Bldg. 1230 12th Street Modesto CA 95354 Landholding Agency: GSA Property Number.... ft. through Sept. 30, 2012. Current usage: gov't offices, asbestos has been identified as well as.... Bldg., 3,713 sq. ft. for the garage, public space (roads and hwy) and utilities easements, asbestos and...

Ligand effects on the ferro- to antiferromagnetic exchange ratio in bis(o-semiquinonato)copper(II).

PubMed

Ovcharenko, Victor I; Gorelik, Elena V; Fokin, Sergey V; Romanenko, Galina V; Ikorskii, Vladimir N; Krashilina, Anna V; Cherkasov, Vladimir K; Abakumov, Gleb A

2007-08-29

Heterospin complexes [Cu(SQ)2Py].C7H8, Cu(SQ)2DABCO, and [Cu(SQ)2NIT-mPy].C6H6, where Cu(SQ)2 is bis(3,6-di-tert-butyl-o-benzosemiquinonato)copper(II), DABCO is 1,4-diazabicyclo(2,2,2)octane, and NIT-mPy is the nitronyl nitroxide 2-(pyridin-3-yl)-4,4,5,5-tetramethyl-4,5-dihydro-1H-imidazole-3-oxide-1-oxyl, have been synthesized. The molecules of these complexes have a specific combination of the intramolecular ferro- and antiferromagnetic exchange interactions between the odd electrons of Cu(II) and SQ ligands, characterized by large exchange coupling parameters |J| approximately 100-300 cm(-1). X-ray and magnetochemical studies of a series of mixed-ligand compounds revealed that an extra ligand (Py, NIT-mPy, or DABCO) coordinated to the metal atom produces a dramatic effect on the magnetic properties of the complex, changing the multiplicity of the ground state. Quantum chemical analysis of magnetostructural correlations showed that the energy of the antiferromagnetic exchange interaction between the odd electrons of the SQ ligands in the Cu(SQ)2 bischelate is extremely sensitive to both the nature of the extra ligand and structural distortions of the coordination unit, arising from extra ligand coordination.

Progress report on the effects of highway construction on suspended-sediment discharge in the Coal River and Trace Fork, West Virginia, 1975-81

USGS Publications Warehouse

Downs, S.C.; Appel, David H.

1986-01-01

Construction of the four-lane Appalachian Corridon G highway disturbed about 2 sq mi in the Coal River and 0.35 sq mi of the 4.75 sq mi Trace Fork basin in southern West Virginia. Construction had a negligible effect on runoff and suspended-sediment load in the Coal River and its major tributaries, the Little Coal and Big Coal Rivers. Drainage areas of the mainstem sites in the Coal River basin ranged from 269 to 862 sq mi, and average annual suspended-sediment yields ranged from 535 to 614 tons/sq mi for the 1975-81 water years. Suspended-sediment load in the smaller Trace Fork basin (4.72 sq mi) was significantly affected by the highway construction. Based on data from undisturbed areas upstream from construction, the normal background load at Trace Fork downstream from construction during the period July 1980 to September 1981 was estimated to be 830 tons; the measured load was 2,385 tons. Runoff from the 0.35 sq mi area disturbed by highway construction transported approximately 1,550 tons of sediment. Suspended-sediment loads from the construction zone were also higher than normal background loads during storms. (USGS)

Near-uv photon efficiency in a TiO2 electrode - Application to hydrogen production from solar energy

NASA Technical Reports Server (NTRS)

Desplat, J.-L.

1976-01-01

An n-type (001) TiO2 electrode irradiated at 365 nm was tested under anodic polarization. A saturation current independent of pH and proportional to light intensity has been observed. Accurate measurements of the incident power lead to a 60 per cent photon efficiency. A photoelectrochemical cell built with such an electrode, operated under solar irradiation without concentration, produced an electrolysis current of 0.7 mA/sq cm without applied voltage.

Study of the space environmental effects on spacecraft engineering materials

NASA Technical Reports Server (NTRS)

Obrien, Susan K.; Workman, Gary L.; Smith, Guy A.

1995-01-01

The space environment in which the Space Station Freedom and other space platforms will orbit is truly a hostile environment. For example, the current estimates of the integral fluence for electrons above 1 Mev at 2000 nautical miles is above 2 x 10(exp 10) electrons/sq cm/day. and the proton integral fluence is above 1 x 109 protons/sq cm/day. At the 200 - 400 nautical miles, which is more representative of the altitude which will provide the environment for the Space Station, each of these fluences will be proportionately less; however, the data indicates that the radiation environment will obviously have an effect on structural materials exposed to the environment for long durations. The effects of this combined environment is the issue which needs to be understood for the long term exposure of structures in space. In order to better understand the effect of these hostile phenomena on spacecraft, several types of studies are worth performing in order to simulate at some level the effect of the environment. For example the effect of protons and electrons impacting structural materials are easily simulated through experiments using the Van de Graff and Pelletron accelerators currently housed in the Environmental Effects Facility at MSFC. Proton fluxes with energies of 700 Kev-2.5 Mev can be generated and used to impinge on sample targets to determine the effects of the particles. Also the Environmental Effects Facility has the capability to generate electron beams with energies from 700 Kev to 2.5 Mev. These facilities will be used in this research to simulate space environmental effects from energetic particles. Ultraviolet radiation, particularly in the ultraviolet (less than 400 nm wavelength) is less well characterized at this time. The Environmental Effects Facility has a vacuum system dedicated to studying the effects of ultraviolet radiation on specific surface materials. This particular system was assembled in a previous study (NAS8-38609) in order to perform a variety of experiments on materials proposed for the Space Station. That system has continued to function as planned and has been used in carrying out portions of the proposed study.

Evaluating the Responsiveness to Therapeutic Change with Routine Outcome Monitoring: A Comparison of the Symptom Questionnaire-48 (SQ-48) with the Brief Symptom Inventory (BSI) and the Outcome Questionnaire-45 (OQ-45).

PubMed

Carlier, Ingrid V E; Kovács, Viktória; van Noorden, Martijn S; van der Feltz-Cornelis, Christina; Mooij, Nanda; Schulte-van Maaren, Yvonne W M; van Hemert, Albert M; Zitman, Frans G; Giltay, Erik J

2017-01-01

Assessment of psychological distress is important, because it may help to monitor treatment effects and predict treatment outcomes. We previously developed the 48-item Symptom Questionnaire (SQ-48) as a public domain self-report psychological distress instrument and showed good internal consistency as well as good convergent and divergent validity among clinical and non-clinical samples. The present study, conducted among psychiatric outpatients in a routine clinical setting, describes additional psychometric properties of the SQ-48. The primary focus is on responsiveness to therapeutic change, which to date has been rarely examined within psychiatry or clinical psychology. Since a questionnaire should also be stable when no clinically important change occurs, we also examined test-retest reliability within a test-retest design before treatment (n = 43). A pre-treatment/post-treatment design was used for responsiveness to therapeutic change, comparing the SQ-48 with two internationally widely used instruments: the Brief Symptom Inventory (n = 97) and the Outcome Questionnaire-45 (n = 109). The results showed that the SQ-48 has excellent test-retest reliability and good responsiveness to therapeutic change, without significant differences between the questionnaires in terms of responsiveness. In sum, the SQ-48 is a psychometrically sound public domain self-report instrument that can be used for routine outcome monitoring, as a benchmark tool or for research purposes. Copyright © 2015 John Wiley & Sons, Ltd. Key Practitioner Message The SQ-48 is developed as a public domain self-report questionnaire, in line with growing efforts to develop clinical instruments that are free of charge. The SQ-48 has excellent test-retest reliability and good responsiveness to therapeutic change or patient progress. There were no significant differences in terms of responsiveness between the SQ-48 and BSI or OQ-45. The SQ-48 can be used as a routine evaluation outcome measure for quality assurance in clinical practice. Providing feedback on patient progress via outcome measures could contribute to the enhancement of treatment outcomes. Copyright © 2015 John Wiley & Sons, Ltd.

Alluvial Fan Delineation from SAR and LIDAR-Derived Digital Elevation Models in the Philippines

NASA Astrophysics Data System (ADS)

Aquino, D. T.; Ortiz, I.; Timbas, N.; Gacusan, R.; Montalbo, K.; Eco, R. C.; Lagmay, A.

2013-12-01

Occurrence of floods and debris flows leading to the formation of alluvial fans at the base of mountains naturally improve fertility of alluvial plains. However, these formations also have detrimental effects to communities within these zones like the case of Barangay (village) Andap, New Bataan, Compostela Valley where the whole village was wiped out by debris flow when it was hit by Supertyphoon Bopha in 2012. Hence, demarcating the boundaries of alluvial fans is crucial in disaster preparedness and mitigation. This study describes a method to delineate alluvial fans through contour maps from SAR and LiDAR-derived digital elevation models. Based on this data, we used hydrographic apex point polygons to plot the outflow points of upstream watersheds. The watershed and alluvial fan polygons were used to simulate debris flows in the study sites. The fans generated from the flood simulation were consistent with the polygons delineated from the digital elevation model. Satellite imagery and evidences of alluvial deposits found on site revealed 392 alluvial fans in the country. Widest among these is the sprawling 760 sq km fan identified in Cagayan Valley threatening about 434,329 persons at risk of debris flow. Other fans include those identified in Calapan, Mindoro (531 sq km), Kaliwanagan, Pangasinan (436 sq km), Pampanga Alluvial Fan (325 sq km), Mina, Iloilo (315 sq km), Lamsugod, S. Cotabato (286 sq km), in Tignaman, Oton and Alimodian in Iloilo (272 sq km), and the bajada, a series of alluvial fan coalescing to form a larger fan, identified in Ilocos Norte (218 sq km).

Estimation of Aerosol Direct Radiative Effects Over the Mid-Latitude North Atlantic from Satellite and In Situ Measurements

NASA Technical Reports Server (NTRS)

Bergstrom, Robert W.; Russell, P. B.

2000-01-01

We estimate solar radiative flux changes due to aerosols over the mid-latitude North Atlantic by combining optical depths from AVHRR measurements with aerosol properties from the recent TARFOX program. Results show that, over the ocean the aerosol decreases the net radiative flux at the tropopause and therefore has a cooling effect. Cloud-free, 24-hour average flux changes range from -9 W/sq m near the eastern US coast in summer to -1 W/sq m in the mid-Atlantic during winter. Cloud-free North Atlantic regional averages range from -5.1 W/sq m in summer to -1.7 W/sq m in winter, with an annual average of -3.5 W/sq m. Cloud effects estimated from ISCCP data, reduce the regional annual average to -0.8 W/sq m. All values are for the moderately absorbing TARFOX aerosol (omega(0.55 microns) = 0.9); values for a nonabsorbing aerosol are approx. 30% more negative. We compare our results to a variety of other calculations of aerosol radiative effects.

Polymeric nanotheranostics for real-time non-invasive optical imaging of breast cancer progression and drug release.

PubMed

Ferber, Shiran; Baabur-Cohen, Hemda; Blau, Rachel; Epshtein, Yana; Kisin-Finfer, Einat; Redy, Orit; Shabat, Doron; Satchi-Fainaro, Ronit

2014-09-28

Polymeric nanocarriers conjugated with low molecular weight drugs are designed in order to improve their efficacy and toxicity profile. This approach is particularly beneficial for anticancer drugs, where the polymer-drug conjugates selectively accumulate at the tumor site, due to the enhanced permeability and retention (EPR) effect. The conjugated drug is typically inactive, and upon its pH- or enzymatically-triggered release from the carrier, it regains its therapeutic activity. These settings lack information regarding drug-release time, kinetics and location. Thereby, real-time non-invasive intravital monitoring of drug release is required for theranostics (therapy and diagnostics). We present here the design, synthesis and characterization of a theranostic nanomedicine, based on N-(2-hydroxypropyl) methacrylamide (HPMA) copolymer, owing its fluorescence-based monitoring of site-specific drug release to a self-quenched near-infrared fluorescence (NIRF) probe. We designed two HPMA copolymer-based systems that complement to a theranostic nanomedicine. The diagnostic system consists of self-quenched Cy5 (SQ-Cy5) as a reporter probe and the therapeutic system is based on the anticancer agent paclitaxel (PTX). HPMA copolymer-PTX/SQ-Cy5 systems enable site-specific release upon enzymatic degradation in cathepsin B-overexpressing breast cancer cells. The release of the drug occurs concomitantly with the activation of the fluorophore to its Turn-ON state. HPMA copolymer-SQ-Cy5 exhibits preferable body distribution and drug release compared with the free drug and probe when administered to cathepsin B-overexpressing 4T1 murine mammary adenocarcinoma-bearing mice. This approach of co-delivery of two complementary systems serves as a proof-of-concept for real-time deep tissue intravital orthotopic monitoring and may have the potential use in clinical utility as a theranostic nanomedicine. Copyright © 2014. Published by Elsevier Ireland Ltd.

n-MoSe2 photoelectrochemical halogen storage cell

NASA Astrophysics Data System (ADS)

Ang, P. G. P.; Sammells, A. F.

1982-01-01

In the study reported here, single-crystal n-MoSe2 photoanodes are investigated in a variety of halogen redox couples. The photoanode is prepared by allowing the silver epoxy cement to come into contact with the front surface of the crystal before being insulated from the redox electrolyte with paraffin wax. This photoanode is evaluated in bromine redox electrolytes in various pH ranges. In 1M HBr + 1M Br2 (pH, approximately zero), the initial open-circuit potential of the MoSe2 versus a platinum reference electrode in the same electrolyte is -130 mV in the dark and -480 mV under 200 mW/sq cm xenon illumination. It is noted that improved performance could be achieved with such crystals by subjecting them to an anodic polarization of around 1 volt from the initial resting potential, a current of about 5 mA/sq cm flowing in the dark.

Silicon solar cell characterization at low temperatures and low illumination as a function of particulate irradiation

NASA Technical Reports Server (NTRS)

Whitaker, A. F.; Little, S. A.; Peacock, C. L., Jr.

1983-01-01

Various configurations of back surface reflector silicon solar cells including small (2 x 2) cm and large (approx. 6 x 6) cm cells with conventional and wraparound contacts were subjected to 1 MeV electron irradiation and characterized under both Earth orbital and deep space conditions of temperatures and illuminations. Current-Voltage (I-V) data were generated from +65 C to -150 C and at incident illuminations from 135.3 mW/sq cm to 5.4 mW/sq cm for these cells. Degradation in cell performance which is manifested only under deep space conditions is emphasized. In addition, the effect of particle irradiation on the high temperature and high intensity and low temperature and low intensity performance of the cells is described. The cells with wraparound contacts were found to have lower efficiencies at Earth orbital conditions than the cells with conventional contacts.

Solar Wind Charge Exchange and Local Hot Bubble X-Ray Emission with the DXL Sounding Rocket Experiment

NASA Technical Reports Server (NTRS)

Galeazzi, M.; Collier, M. R.; Cravens, T.; Koutroumpa, D.; Kuntz, K. D.; Lepri, S.; McCammon, D.; Porter, F. S.; Prasai, K.; Robertson, I.;

Direct synthesis of graphene on silicon oxide by low temperature plasma enhanced chemical vapor deposition.

PubMed

Muñoz, Roberto; Martínez, Lidia; López-Elvira, Elena; Munuera, Carmen; Huttel, Yves; García-Hernández, Mar

2018-06-27

Direct graphene growth on silicon with a native oxide using plasma enhanced chemical vapour deposition at low temperatures [550 °C-650 °C] is demonstrated for the first time. It is shown that the fine-tuning of a two-step synthesis with gas mixtures C2H2/H2 yields monolayer and few layer graphene films with a controllable domain size from 50 nm to more than 300 nm and the sheet resistance ranging from 8 kΩ sq-1 to less than 1.8 kΩ sq-1. Differences are understood in terms of the interaction of the plasma species - chiefly atomic H - with the deposited graphene and the native oxide layer. The proposed low temperature direct synthesis on an insulating substrate does not require any transfer processes and improves the compatibility with the current industrial processes.

Determination of optimum fin profile for a zero-G capillary drained condenser

NASA Technical Reports Server (NTRS)

Mccormick, John A.; Valenzuela, Javier A.; Choudhury, Dipanker

1990-01-01

This paper presents the analytical formulation and numerical results for heat transfer in a high heat flux condenser that relies on capillary flow along shaped fins (Gregorig surfaces) and a drainage network embedded in the condenser walls. Results are shown for a variety of fin profile shapes in order to show the geometric trade-offs involved in seeking a maximum effective heat transfer coefficient for the fin. Predictions of the model show excellent agreement with previously reported measurements for steam. Based on this work, a profile has been selected for a 2 kW ammonia condenser currently under development for use in space. In that design the fin half width is 0.5 mm and the model predicts a heat transfer coefficient referred to the base of the fin of 9 W/sq cm deg C for a heat flux of 10/W sq cm at the base.

Single event effects and laser simulation studies

NASA Technical Reports Server (NTRS)

Kim, Q.; Schwartz, H.; Mccarty, K.; Coss, J.; Barnes, C.

1993-01-01

The single event upset (SEU) linear energy transfer threshold (LETTH) of radiation hardened 64K Static Random Access Memories (SRAM's) was measured with a picosecond pulsed dye laser system. These results were compared with standard heavy ion accelerator (Brookhaven National Laboratory (BNL)) measurements of the same SRAM's. With heavy ions, the LETTH of the Honeywell HC6364 was 27 MeV-sq cm/mg at 125 C compared with a value of 24 MeV-sq cm/mg obtained with the laser. In the case of the second type of 64K SRAM, the IBM640lCRH no upsets were observed at 125 C with the highest LET ions used at BNL. In contrast, the pulsed dye laser tests indicated a value of 90 MeV-sq cm/mg at room temperature for the SEU-hardened IBM SRAM. No latchups or multiple SEU's were observed on any of the SRAM's even under worst case conditions. The results of this study suggest that the laser can be used as an inexpensive laboratory SEU prescreen tool in certain cases.

Spectrum of atmospheric gamma rays to 10 MeV at lambda = 40 deg. [as function of altitude

NASA Technical Reports Server (NTRS)

Peterson, L. E.; Schwartz, D. A.; Ling, J. C.

1973-01-01

Results of measurements of the differential counting rate spectra due to atmospheric gamma rays as a function of altitude to 3.6 g/sq cm over Texas. Two gain settings and a 128-channel pulse height analyzer were used to cover the range from 0.2 to 10 MeV. The detector was a 7.6 x 7.6 cm NaI crystal, which was surrounded on five sides by a 2-cm-thick plastic anticoincidence shield for charged particle rejection. The system had a nearly isotropic response to photons above 0.2 MeV. The spectrum at ceiling appeared as a steep continuum with a power-law index of about 1.4. The only obvious feature was the 0.51-MeV positron annihilation line. The spectral shape was independent for depths less than 20 g/sq cm, the absolute intensity varying in proportion to the intensity of the cosmic ray secondary charged particles. Also, at depths less than 30 g/sq cm the observed flux variation with altitude can be described in terms of an empirical depth-dependent source function.

Study of multi-kilowatt solar arrays for Earth orbit applications

NASA Technical Reports Server (NTRS)

Patterson, R. E.

1983-01-01

A miniaturized Cassegrainian concentrator (MCC) solar array concept is being developed with the objective of significantly reducing the recurring cost of multikilowatt solar arrays. The desired cost reduction is obtained as a result of using very small high efficiency solar cells in conjuction with low cost optics. The MCC single element concept incident slar radiation is reflected rom a primary parabolic reflector to a secondary hyperbolic reflector and finally to a 4 millimeter diameter solar cell. A light catcher cone is used to improve off axis performance. The solar cell is mounted to a heat fin. An element is approximately 13 millimeters thick which permits efficient launch stowage of the concentrator system panels without complex optical component deployments or retractions. The MCC elements are packed in bays within graphite epoxy frames and are electrically connected into appropriate series-parallel circuits. A MCC sngle element with a 21 sq cm entrance aperture and a 20 efficient, 0.25 sq cm gallium arsenide solar cell has the same power output as 30 sq cm of 11-percent efficiency (at 68 C) silicon solar cells.

Relativistic heavy cosmic rays

NASA Technical Reports Server (NTRS)

Mewaldt, R. A.; Fernandez, J. I.; Israel, M. H.; Klarmann, J.; Binns, W. R.

1972-01-01

During three balloon flights of a 1 sq m sr ionization chamber/Cerenkov counter detector system, measurements were made of the atmospheric attenuation, flux, and charge composition of cosmic ray nuclei with 16 is less than or = Z is less than or = 30 and rigidity greater than 4.5 GV. The attenuation mean free path in air of VH (20 less than or = Z less than or = 30) nuclei is found to be 19.7 + or - 1.6 g/sq cm, a value somewhat greater than the best previous measurement. The attenuation mean free path of iron is found to be 15.6 + or - 2.2 g/sq cm, consistent with predictions of geometric cross-section formulae. An absolute flux of VH nuclei 10 to 20% higher than earlier experiments at similar geomagnetic cutoff and level of solar activity was measured. The relative abundances of even-charged nuclei are found to be in good agreement with results of other recent high resolution counter experiments. The observed cosmic ray chemical composition implies relative abundances at the cosmic ray source of Ca/Fe = 0.12 + or - 0.04 and S/Fe = 0.14 + or - 0.05.

Strength, body composition, and functional outcomes in the squat versus leg press exercises.

PubMed

Rossi, Fabrício E; Schoenfeld, Brad J; Ocetnik, Skyler; Young, Jonathan; Vigotsky, Andrew; Contreras, Bret; Krieger, James W; Miller, Michael G; Cholewa, Jason

2018-03-01

The purpose of this study was to compare strength, body composition, and functional outcome measures following performance of the back squat, leg press, or a combination of the two exercises. Subjects were pair-matched based on initial strength levels and then randomly assigned to 1 of 3 groups: a squat-only group (SQ) that solely performed squats for the lower body; a leg press-only group (LP) that solely performed leg presses for the lower body, or a combined squat and leg press group (SQ-LP) that performed both squats and leg presses for the lower body. All other RT variables were held constant. The study period lasted 10 weeks with subjects performing 2 lower body workouts per week comprising 6 sets per session at loads corresponding to 8-12 RM with 90- to 120-second rest intervals. Results showed that SQ had greater transfer to maximal squat strength compared to the leg press. Effect sizes favored SQ and SQ-LP versus LP with respect to countermovement jump while greater effect sizes for dynamic balance were noted for SQ-LP and LP compared to SQ, although no statistical differences were noted between conditions. These findings suggest that both free weights and machines can improve functional outcomes, and that the extent of transfer may be specific to the given task.

NASA Redox Project status summary

NASA Technical Reports Server (NTRS)

Hagedorn, N. H.

1983-01-01

This report is a summary of the results of the Redox Project effort during Cy 1982. It was presented at the Fifth U.S. Department of Energy Battery and Electrochemical Contractors Conference, Arlington, Va., Dec. 7-9, 1982. The major development during 1982 was the shift from Redox system operation at 25 C with unmixed reactants to operation at 65 C with mixed reactants. This change has made possible a two- or three-fold increase in operating current density, to about 65 mA/sq cm, and an increase in reactant utilization from 40% to about 90%. Both of these improvements will lead to significant system cost reductions. Contract studies have indicated that Redox reactant costs also will be moderate. A new catalyst for the chromuim electrode offers all the advantages of the conventional gold-lead catalyst while being easier to apply and more forgiving in use.

The electrochemical generation of useful chemical species from lunar materials

NASA Technical Reports Server (NTRS)

Tsai, Kan J.; Kuchynka, Daniel J.; Sammells, Anthony F.

1990-01-01

Electrochemical cells have been fabricated for the simultaneous generation of oxygen and lithium from a Li2O-containing molten salt (Li2O-LiCl-LiF). The cell utilizes an oxygen vacancy conducting solid electrolyte, yttria-stabilized zirconia (YSZ), to effect separation between oxygen evolving and lithium reduction half-cell reactions. The cell, which operates at 700-850 C, possesses rapid electrode kinetics at the lithium-alloy electrode with exchange current density values being greater than 60 mA/sq cm. When used in the electrolytic mode, lithium produced at the negative electrode would be continuously removed from the cell for later use (under lunar conditions) as an easily storable reducing agent for the chemical refining of lunar ores. Because of the high reversibility of this electrochemical system, it has also formed the basis for the lithium-oxygen secondary battery system which possesses the highest theoretical energy density yet investigated.

The electrochemical generation of useful chemical species from lunar materials

NASA Astrophysics Data System (ADS)

Tsai, Kan J.; Kuchynka, Daniel J.; Sammells, Anthony F.

Electrochemical cells have been fabricated for the simultaneous generation of oxygen and lithium from a Li2O-containing molten salt (Li2O-LiCl-LiF). The cell utilizes an oxygen vacancy conducting solid electrolyte, yttria-stabilized zirconia (YSZ), to effect separation between oxygen evolving and lithium reduction half-cell reactions. The cell, which operates at 700-850 C, possesses rapid electrode kinetics at the lithium-alloy electrode with exchange current density values being greater than 60 mA/sq cm. When used in the electrolytic mode, lithium produced at the negative electrode would be continuously removed from the cell for later use (under lunar conditions) as an easily storable reducing agent for the chemical refining of lunar ores. Because of the high reversibility of this electrochemical system, it has also formed the basis for the lithium-oxygen secondary battery system which possesses the highest theoretical energy density yet investigated.

The DES Bright Arcs Survey: Hundreds of Candidate Strongly Lensed Galaxy Systems from the Dark Energy Survey Science Verification and Year 1 Observations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Diehl, H. T.; Buckley-Geer, E. J.; Lindgren, K. A.

We report the results of our searches for strong gravitational lens systems in the Dark Energy Survey (DES) Science Verication and Year 1 observations. The Science Verication data spans approximately 250 sq. deg. with median i

The DES Bright Arcs Survey: Hundreds of Candidate Strongly Lensed Galaxy Systems from the Dark Energy Survey Science Verification and Year 1 Observations

DOE PAGES

Diehl, H. T.; Buckley-Geer, E. J.; Lindgren, K. A.; ...

2017-09-01

We report the results of our searches for strong gravitational lens systems in the Dark Energy Survey (DES) Science Verication and Year 1 observations. The Science Verication data spans approximately 250 sq. deg. with median i

The effect of cropping systems and irrigation management on development of potato early blight

USDA-ARS?s Scientific Manuscript database

Crop and soil management may modify canopy and belowground microclimate. However, their effects on potential development and control of early blight are not well documented. Crop management systems [Status Quo (SQ), Soil Conserving (SC), Soil Improving (SI), Disease Suppressive (DS), and Continuou...

Learning Strategies: Secondary LD Students in the Mainstream.

ERIC Educational Resources Information Center

D'Antoni, Alice; And Others

The paper presents four learning strategy techniques--the SQ3R method of study, the Multipass Strategy, the Advanced Study Guide Technique, and Cognitive Mapping--for use with secondary level learning disabled students. The SQ3R method involves the five steps of survey, question, read, recite, and review. An adaption of the SQ3R method, the…

Sea Ice

NASA Technical Reports Server (NTRS)

Parkinson, Claire L.; Cavalieri, Donald J.

2005-01-01

Sea ice covers vast areas of the polar oceans, with ice extent in the Northern Hemisphere ranging from approximately 7 x 10(exp 6) sq km in September to approximately 15 x 10(exp 6) sq km in March and ice extent in the Southern Hemisphere ranging from approximately 3 x 10(exp 6) sq km in February to approximately 18 x 10(exp 6) sq km in September. These ice covers have major impacts on the atmosphere, oceans, and ecosystems of the polar regions, and so as changes occur in them there are potential widespread consequences. Satellite data reveal considerable interannual variability in both polar sea ice covers, and many studies suggest possible connections between the ice and various oscillations within the climate system, such as the Arctic Oscillation, North Atlantic Oscillation, and Antarctic Oscillation, or Southern Annular Mode. Nonetheless, statistically significant long-term trends are also apparent, including overall trends of decreased ice coverage in the Arctic and increased ice coverage in the Antarctic from late 1978 through the end of 2003, with the Antarctic ice increases following marked decreases in the Antarctic ice during the 1970s. For a detailed picture of the seasonally varying ice cover at the start of the 21st century, this chapter includes ice concentration maps for each month of 2001 for both the Arctic and the Antarctic, as well as an overview of what the satellite record has revealed about the two polar ice covers from the 1970s through 2003.

Squatting Exercises in Older Adults: Kinematic and Kinetic Comparisons

PubMed Central

FLANAGAN, SEAN; SALEM, GEORGE J.; WANG, MAN-YING; SANKER, SERENA E.; GREENDALE, GAIL A.

2012-01-01

Purpose Squatting activities may be used, within exercise programs, to preserve physical function in older adults. This study characterized the lower-extremity peak joint angles, peak moments, powers, work, impulse, and muscle recruitment patterns (electromyographic; EMG) associated with two types of squatting activities in elders. Methods Twenty-two healthy, older adults (ages 70–85) performed three trials each of: 1) a squat to a self-selected depth (normal squat; SQ) and 2) a squat onto a chair with a standardized height of 43.8 cm (chair squat; CSQ). Descending and ascending phase joint kinematics and kinetics were obtained using a motion analysis system and inverse dynamics techniques. Results were averaged across the three trials. A 2 × 2 (activity × phase) ANOVA with repeated measures was used to examine the biomechanical differences among the two activities and phases. EMG temporal characteristics were qualitatively examined. Results CSQ generated greater hip flexion angles, peak moments, power, and work, whereas SQ generated greater knee and ankle flexion angles, peak moments, power, and work. SQ generated a greater knee extensor impulse, a greater plantar flexor impulse and a greater total support impulse. The EMG temporal patterns were consistent with the kinetic data. Conclusions The results suggest that, with older adults, CSQ places greater demand on the hip extensors, whereas SQ places greater demand on the knee extensors and ankle plantar flexors. Clinicians may use these discriminate findings to more effectively target specific lower-extremity muscle groups when prescribing exercise for older adults. PMID:12673148

Search for Doppler-shifted gamma-ray emission from SS 433 using the SMM spectrometer

NASA Technical Reports Server (NTRS)

Geldzahler, B. J.; Share, G. H.; Kinzer, R. L.; Magura, J.; Chupp, E. L.

1989-01-01

Data accumulated from 1980 to 1983 with the Gamma Ray Spectrometer aboard NASA's Solar Maximum Mission (SMM) satellite were searched for evidence of red and blue Doppler-shifted 1.37 MeV Mg-24 nuclear lines from SS 433. The SMM data base covers 270 days when SS 433 was in the field of view and includes periods of radio flaring and quiescence. No evidence was found for Doppler-shifted line emission in any of the spectra. The range of 3-sigma upper limits for individual 9 day integration periods was 0.0008-0.0023 photons/sq cm per sec for the blue beam, encompassing the reported about 1.5 MeV line, and 0.0008-0.002 photons/sq cm per sec for the red beam, encompassing the reported about 1.2 MeV line; the average 3-sigma upper limit in each beam for shifted about 1.37 MeV lines is 0.0015 photons/sq cm per sec for single 9 day integrations. The 3-sigma upper limit on 1.37 MeV gamma-ray emission over 23 9-day integration intervals for the red beam and 28 intervals for the blue beam is 0.0002 photons/sq cm per sec. These new limits from SMM can be reconciled with the HEAO 3 results only if SS 433 emits gamma radiation at or above the SMM sensitivity limit on rare occasions due to variable physical conditions in the system.

75 FR 9207 - Notice of a Project Waiver of Section 1605 (Buy American Requirement) of the American Recovery...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-01

... the purchase of a GrundFos SQ Flex 6 SQF- 2 solar powered submersible pump system with control and solar panels (pump system) manufactured in Denmark by GrundFos. This is a project specific waiver and... powered submersible pump system with control and solar panels (pump system) manufactured in Denmark by...

Satiety quotient linked to food intake and changes in anthropometry during menopause: a MONET Study.

PubMed

McNeil, J; Prud'homme, D; Strychar, I; Rabasa-Lhoret, R; Brochu, M; Lavoie, J-M; Doucet, E

2014-08-01

It is unknown whether the satiety quotient (SQ) differs across the menopausal transition, and whether changes in SQ are related to changes in anthropometric/body composition variables. The objective of this study was to evaluate the changes in SQ and its association with energy intake and changes in anthropometric/body composition variables across the menopausal transition. At baseline, 102 premenopausal women (aged 49.9 ± 1.9 years, body mass index 23.3 ± 2.2 kg/m(2)) took part in a 5-year observational, longitudinal study. Body composition (DXA), appetite (visual analog scales), energy and macronutrient intakes (ad libitum lunch and 7-day food diary) were assessed annually. The SQ (mm/100 kcal) was calculated at 60 and 180 min post-breakfast consumption. Overall, the SQ increased at years 3 and 4 (p = 0.01-0.0001), despite no significant differences between menopausal status groups. Lower fullness, prospective food consumption and mean SQ values predicted overall increases in lunch energy and macronutrient intakes (p = 0.04-0.01), whereas only prospective food consumption and fullness SQ predicted energy intake and carbohydrate intake, respectively, when assessed with food diaries (p = 0.01). Delta SQs were negatively correlated with changes in waist circumference (p = 0.03-0.02), whereas delta SQs were positively (p = 0.04) and negatively (p = 0.02) associated with delta fat mass between years 1 and 5, and years 4 and 5, respectively. These results suggest that variations in SQ across the menopausal transition are related to energy and macronutrient intakes and coincide with changes in body composition and waist circumference.

Comparison of methods to assess adherence to small-quantity lipid-based nutrient supplements (SQ-LNS) and dispersible tablets among young Burkinabé children participating in a community-based intervention trial.

PubMed

Abbeddou, Souheila; Hess, Sonja Y; Yakes Jimenez, Elizabeth; Somé, Jérôme W; Vosti, Stephen A; Guissou, Rosemonde M; Ouédraogo, Jean-Bosco; Brown, Kenneth H

2015-12-01

Adherence to supplementation provided during an intervention trial can affect interpretation of study outcomes. We compared different approaches for estimating adherence to small-quantity lipid-based nutrient supplements (SQ-LNS) and dispersible tablets in a randomised clinical trial in Burkina Faso. A total of 2435 children (9-18 months) were randomly assigned to receive daily 20 g SQ-LNS with varying contents of zinc and a dispersible tablet containing 0 or 5 mg zinc. Adherence to SQ-LNS and tablets was assessed for all children through weekly caregiver interviews, and disappearance rate was calculated based on empty and unused packages returned during home visits. Additional adherence data were collected in different randomly selected subgroups of children: 12-h home observations were completed for children 11 and 16 months of age (n = 192) to assess consumption of SQ-LNS and dispersible tablets, and plasma zinc concentration was measured at baseline and 18 months (n = 310). Apparent adherence to SQ-LNS and dispersible tablets differed according to the assessment method used. Average daily caregiver-reported adherence to both SQ-LNS and dispersible tablets was 97 ± 6%. Disappearance rates showed similarly high average weekly adherence (98 ± 4%). In contrast, only 63% and 54% of children at 11 and 16 months, respectively, received SQ-LNS during the 12-h home observation periods, and fewer (32% and 27%) received a tablet. The lack of change in plasma zinc concentration after 9 months of supplementation suggests low adherence to the zinc tablet. Better methods are needed to assess adherence in community-based supplementation trials. © 2014 John Wiley & Sons Ltd.

Low frequency electrical noise across contacts between a normal conductor and superconducting bulk YBa2Cu3O7

NASA Technical Reports Server (NTRS)

Hall, J.; Chen, T. M.

1991-01-01

Virtually every device that makes use of the new ceramic superconductors will need normal conductor to superconductor contacts. The current-voltage and electrical noise characteristics of these contacts could become important design considerations. I-V and low frequency electrical noise measurements are presented on contacts between a normal conductor and superconducting polycrystalline YBa2Cu3O7. The contacts were formed by first sputtering gold palladium pads onto the surface of the bulk superconductor and then using silver epoxy to attach a wire(s) to each pad. Voltage across the contacts was found for small current densities. The voltage spectral density, S sub v(f), a quantity often used to characterize electrical noise, very closely followed an empirical relationship given by S sub v(f) = C(VR)sq/f, where V is the DC voltage across the contact, R is the contact resistance, F is frequency, and C is a contant found to be 2 x 10(exp -10)/Omega sq at 78 K. This relationship was found to be independent of contact area, contact geometry, sample fabrication technique, and sample density.

Low frequency electrical noise across contacts between a normal conductor and superconducting bulk YBa2Cu3O7

NASA Technical Reports Server (NTRS)

Hall, J.; Chen, T. M.

1990-01-01

Virtually every device that makes use of the new ceramic superconductors will need normal conductor to supercondutor contacts. The current-voltage and electrical noise characteristics of these contacts could be become important design considerations. I-V and low frequency electrical noise measurements are presented on contacts between a normal conductor and superconducting polycrystalline YBa2Cu3O7. The contacts were formed by first sputtering gold palladium pads onto the surface of the bulk superconductor and then using silver epoxy to attach a wire(s) to each pad. Voltage across the contacts was found for small current densities. The voltage spectral density, S sub v(f), a quanity often used to characterize electrical noise, very closely followed an empirical relationship given by, S sub v(f) = C(VR)sq/f, where V is the DC voltage across the contact, R is the contact resistance, F is frequency, and C is a contant found to be 2 x 10(exp -10)/Omega sq at 78 K. This relationship was found to be independent of contact area, contact geometry, sample fabrication technique, and sample density.

Evaluation of a microwave high-power reception-conversion array for wireless power transmission

NASA Technical Reports Server (NTRS)

Dickinson, R. M.

1975-01-01

Initial performance tests of a 24-sq m area array of rectenna elements are presented. The array is used as the receiving portion of a wireless microwave power transmission engineering verification test system. The transmitting antenna was located at a range of 1.54 km. Output dc voltage and power, input RF power, efficiency, and operating temperatures were obtained for a variety of dc load and RF incident power levels at 2388 MHz. Incident peak RF intensities of up to 170 mW/sq cm yielded up to 30.4 kW of dc output power. The highest derived collection-conversion efficiency of the array was greater than 80 percent.

Development of fused slurry silicide coatings for tantalum reentry heat shields

NASA Technical Reports Server (NTRS)

Warnock, R. V.; Stetson, A. R.

1972-01-01

A fused slurry silicide coating was developed to provide atmospheric reentry protection for the 90Ta-lOW alloy. Overlaying the silicide with a highly refractory glass greatly improved total lifetime and reliability of the coating system. Low pressure, slow cycle lifetimes in excess of 100 cycles were consistently recorded for 1700 K - 13 and 1300 N/sq m test conditions. A minimum of 25 cycles was obtained for 1810 K - 1300 N/sq m conditions. About 50 simulated reentry cycles (variable temperature, pressure, and stress) were endured by coated 1-inch miniature heat shield panels when exposed to a maximum of 1700 K and either internal or external pressure conditions.

Enhanced solar energy options using earth-orbiting mirrors

NASA Technical Reports Server (NTRS)

Gilbreath, W. P.; Billman, K. W.; Bowen, S. W.

1978-01-01

A system of orbiting space reflectors is described, analyzed, and shown to economically provide nearly continuous insolation to preselected ground sites, producing benefits hitherto lacking in conventional solar farms and leading to large reductions in energy costs for such installations. Free-flying planar mirrors of about 1 sq km are shown to be optimum and can be made at under 10 g/sq m of surface, thus minimizing material needs and space transportation costs. Models are developed for both the design of such mirrors and for the analysis of expected ground insolation as a function of orbital parameters, time, and site location. Various applications (agricultural, solar-electric production, weather enhancement, etc.) are described.

A Plasma Ultraviolet Source for Short Wavelength Lasers.

DTIC Science & Technology

1988-04-15

plasma focus (DPF) device was evaluated for the feasibility of blue-green and near ultraviolet laser pumping. As the result of optimizing the operating conditions of DPF and laser system, the maximum untuned laser output exceeded 4.0mJ corresponding to the energy density 8.3J/liter which is much higher than the typical flashlamp dye laser. The spectral irradiance of DPF at the absorption bands for LD390 and LD490 were 5.5W/sq cm-nm, 0.3W.sq cm-nm, respectively. Due to the lower pump power of DPF at 355nm than the threshold of LD390, the laser pumping of LD390 dye was not

Technology Transfer Demonstration Project. Progress report, December 1993--January 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1994-06-01

The Rural Enterprises Industrial Incubator program offers beginning business a stable foundation on which to build long-term profitable concerns. These incubator facilities consist of buildings for the specific purpose of starting a new manufacturing business and are designed to accommodate a variety of manufacturing firms. Incubators are located on the Kiamichi Area Vocational Technical School system (KAVTS) campuses in Durant, Atoka, Hugo, McAlester, Stigler, Poteau, Idabel, at the REI headquarters and one in Bennington, OK. These facilities range in size from 4,800 sq.ft. to 14,000 sq.ft. and have housed businesses such as machine shops, metal fabrication companies, electronic assembly andmore » biomedical engineering firms.« less

Production of O(-) from CO2 by dissociative electron attachment

NASA Technical Reports Server (NTRS)

Orient, O. J.; Srivastava, S. K.

1983-01-01

Dissociative electron attachment cross-section measurements for the production of O(-) from CO2 are performed using a crossed target-beam - electron-beam collision geometry and a quadrupole mass spectrometer. The relative flow technique is used in determining the absolute values of the cross sections. The attachment energies corresponding to the five cross-section maxima are given. They are 4.4 + or - 0.1, 8.2 + or - 0.1, 13.0 + or - 0.2, 16.9 + or - 0.2, and 19.4 + or 0.2 eV. Also given are the cross sections at these maxima: 1.43 x 10 to the -19th sq cm, 4.48 x 10 to the -19th sq cm, 8.1 x 10 to the -21st sq cm, 8.1 x 10 to the -21st sq cm, and 1.2 x 10 to the -20th sq cm, respectively.

Methane emissions from tundra environments in the Yukon-Kuskokwin Delta, Alaska

NASA Technical Reports Server (NTRS)

Bartlett, Karen B.; Crill, Patrick M.; Sass, Ronald L.; Harriss, Robert C.; Dise, Nancy B.

1992-01-01

This paper reports CH4 flux to the atmosphere from a variety of tundra environments near Bethel, Alaska during the summer months of 1988. Emissions from wet meadow tundra averaged 144 +/- 31 mg/sq m/d and ranged from 15.6 to 426 mg/sq m/d varying with soil moisture and temperature. Flux from the drier upland tundra was about two orders of magnitude lower and averaged 2.3 +/- 1.1 mg/sq m/d. Tundra lakes emit CH4 from the open water surface as well as from fringing aquatic vegetation; the presence of vegetation significantly enhanced flux over open water rates. Calculated diffusive fluxes from open water varied with lake size, the large lakes emitting 3.8 mg/sq m/d and small lakes emitting an average of 77 mg/sq m/d. An updated estimate of global emissions from tundra indicates an annual fluxes of approximately 11 +/- 3 Tg CH4.

Fabrication of demultiplexer for T bps optical signals by using spincoated squarylium dye J-aggregates exhibiting femtosecond optical response

NASA Astrophysics Data System (ADS)

Iwasa, Izumi; Furuki, Makoto; Tian, Minquan; Sato, Yasuhiro; Pu, Lyong S.; Tatsuura, Setoshi; Wada, Osamu

2001-06-01

We fabricated spincoated films of squarylium dye (SQ) J- aggregates exhibiting femtosecond optical response at room temperature. Optical dynamics measurements revealed that the saturable absorption of the SQ J-aggregates film exhibited a decay time of less than 100 fs at a pump energy of 80 fJ/micrometer2. With this ultrafast SQ optical film, four- output demultiplex operation for T bps pulses was demonstrated. A series of 4 optical pulses with 100 fs duration and 1 ps interval (corresponding to 1 T bps signals) were irradiated onto the SQ film synchronized with a 100 fs gate pulse at a finite angle. Four demultiplexed signals were clearly observed at different areas on the CCD camera. Multi- output serial-to-parallel demultiplexer for T bps optical signals can be formed using the SQ J-aggregates film.

Nonadditive entropy Sq and nonextensive statistical mechanics: Applications in geophysics and elsewhere

NASA Astrophysics Data System (ADS)

Tsallis, Constantino

2012-06-01

The celebrated Boltzmann-Gibbs (BG) entropy, S BG = -kΣi p i ln p i, and associated statistical mechanics are essentially based on hypotheses such as ergodicity, i.e., when ensemble averages coincide with time averages. This dynamical simplification occurs in classical systems (and quantum counterparts) whose microscopic evolution is governed by a positive largest Lyapunov exponent (LLE). Under such circumstances, relevant microscopic variables behave, from the probabilistic viewpoint, as (nearly) independent. Many phenomena exist, however, in natural, artificial and social systems (geophysics, astrophysics, biophysics, economics, and others) that violate ergodicity. To cover a (possibly) wide class of such systems, a generalization (nonextensive statistical mechanics) of the BG theory was proposed in 1988. This theory is based on nonadditive entropies such as S_q = kfrac{{1 - sumnolimits_i {p_i^q } }} {{q - 1}}left( {S_1 = S_{BG} } right). Here we comment some central aspects of this theory, and briefly review typical predictions, verifications and applications in geophysics and elsewhere, as illustrated through theoretical, experimental, observational, and computational results.

A comparative study of PD-L1 immunohistochemical assays with four reliable antibodies in thymic carcinoma.

PubMed

Sakane, Tadashi; Murase, Takayuki; Okuda, Katsuhiro; Takino, Hisashi; Masaki, Ayako; Oda, Risa; Watanabe, Takuya; Kawano, Osamu; Haneda, Hiroshi; Moriyama, Satoru; Saito, Yushi; Yamada, Takeshi; Nakanishi, Ryoichi; Inagaki, Hiroshi

2018-01-23

Currently, four immunohistochemical assays are registered with the US Food and Drug Administration to detect the expression of PD-L1. We investigated the PD-L1 expression in thymic carcinomas using these four diagnostic assays. The cases of 53 patients were reviewed and their specimens were subjected to four PD-L1 assays with different antibodies (SP142, SP263, 22C3, and 28-8). The PD-L1 expression in tumor cells (TCs) and immune cells (ICs) was evaluated. In TCs, the four assays showed similar scores in each case. Histopathologically, high TC scores were observed in squamous cell carcinomas (SqCCs). Meanwhile, there were no significant relationships among the IC scores in the four assays. In SqCCs, the high expression of PD-L1 (defined as ≥50% TC score) in TCs tended to be associated with early stage cancer. The patients with high expression levels of PD-L1 tended to show longer overall survival in the 22C3 assays (p=0.0200). In thymic carcinomas, the staining pattern showed high concordance among the four assays when TCs - rather than ICs - were stained. High PD-L1 positivity in TCs, especially in SqCCs, indicated that PD-1/PD-L1 targeted therapy may be a promising therapeutic approach.

Composite ceramic superconducting wires for electric motor applications

NASA Astrophysics Data System (ADS)

Halloran, John W.

1990-07-01

Several types of HTSC wire have been produced and two types of HTSC motors are being built. Hundreds of meters of Ag- clad wire were fabricated from YBa2Cu3O(7-x) (Y-123) and Bi2Ca2Sr2Cu3O10 (BiSCCO). The dc homopolar motor coils are not yet completed, but multiple turns of wire have been wound on the coil bobbins to characterize the superconducting properties of coiled wire. Multifilamentary conductors were fabricated as cables and coils. The sintered polycrystalline wire has self-field critical current densities (Jc) as high as 2800 A/sq cm, but the Jc falls rapidly with magnetic field. To improve Jc, sintered YBCO wire is melt textured with a continuous process which has produced textures wire up to 0.5 meters long with 77K transport Jc above 11, 770 A/sq cm2 in self field and 2100 A/sq cm2 at 1 telsa. The Emerson Electric dc homopolar HTSC motor has been fabricated and run with conventional copper coils. A novel class of potential very powerful superconducting motors have been designed to use trapped flux in melt textures Y-123 as magnet replicas in an new type of permanent magnet motor. The stator element and part of the rotor of the first prototype machine exist, and the HTSC magnet replica segments are being fabricated.

Totally embedded hybrid thin films of carbon nanotubes and silver nanowires as flat homogenous flexible transparent conductors.

PubMed

Pillai, Suresh Kumar Raman; Wang, Jing; Wang, Yilei; Sk, Md Moniruzzaman; Prakoso, Ari Bimo; Rusli; Chan-Park, Mary B

2016-12-08

There is a great need for viable alternatives to today's transparent conductive film using largely indium tin oxide. We report the fabrication of a new type of flexible transparent conductive film using silver nanowires (AgNW) and single-walled carbon nanotube (SWCNT) networks which are fully embedded in a UV curable resin substrate. The hybrid SWCNTs-AgNWs film is relatively flat so that the RMS roughness of the top surface of the film is 3 nm. Addition of SWCNTs networks make the film resistance uniform; without SWCNTs, sheet resistance of the surface composed of just AgNWs in resin varies from 20 Ω/sq to 10 7  Ω/sq. With addition of SWCNTs embedded in the resin, sheet resistance of the hybrid film is 29 ± 5 Ω/sq and uniform across the 47 mm diameter film discs; further, the optimized film has 85% transparency. Our lamination-transfer UV process doesn't need solvent for sacrificial substrate removal and leads to good mechanical interlocking of the nano-material networks. Additionally, electrochemical study of the film for supercapacitors application showed an impressive 10 times higher current in cyclic voltammograms compared to the control without SWCNTs. Our fabrication method is simple, cost effective and enables the large-scale fabrication of flat and flexible transparent conductive films.

Totally embedded hybrid thin films of carbon nanotubes and silver nanowires as flat homogenous flexible transparent conductors

NASA Astrophysics Data System (ADS)

Pillai, Suresh Kumar Raman; Wang, Jing; Wang, Yilei; Sk, Md Moniruzzaman; Prakoso, Ari Bimo; Rusli; Chan-Park, Mary B.

2016-12-01

There is a great need for viable alternatives to today’s transparent conductive film using largely indium tin oxide. We report the fabrication of a new type of flexible transparent conductive film using silver nanowires (AgNW) and single-walled carbon nanotube (SWCNT) networks which are fully embedded in a UV curable resin substrate. The hybrid SWCNTs-AgNWs film is relatively flat so that the RMS roughness of the top surface of the film is 3 nm. Addition of SWCNTs networks make the film resistance uniform; without SWCNTs, sheet resistance of the surface composed of just AgNWs in resin varies from 20 Ω/sq to 107 Ω/sq. With addition of SWCNTs embedded in the resin, sheet resistance of the hybrid film is 29 ± 5 Ω/sq and uniform across the 47 mm diameter film discs; further, the optimized film has 85% transparency. Our lamination-transfer UV process doesn’t need solvent for sacrificial substrate removal and leads to good mechanical interlocking of the nano-material networks. Additionally, electrochemical study of the film for supercapacitors application showed an impressive 10 times higher current in cyclic voltammograms compared to the control without SWCNTs. Our fabrication method is simple, cost effective and enables the large-scale fabrication of flat and flexible transparent conductive films.

Land and Land-use Change in the Climate Sensitive High Plains: An Automated Approach with Landsat

NASA Technical Reports Server (NTRS)

Goetz, Alexander F.; Williams, D. L. (Technical Monitor)

2002-01-01

The High Plains is an economically important and climatologically sensitive region of the United States and Canada. The High Plains contain 100,000 sq km of Holocene sand dunes and sand sheets that are currently stabilized by natural vegetation. Droughts and the larger threat of global warming are climate phenomena that could cause depletion of natural vegetation and make this region susceptible to sand dune reactivation. The original proposal was directed toward the use of Landsat TM data to establish the state and ongoing changes of the surface in the 1.2 million sq. km, semi-arid High Plains region of the central US, A key objective was to develop a model to predict the reactivation of the 100,000 sq. km of Holocene dunes found on the High Plains during an extended drought. At least one Landsat 5 image per year for 1985, 1988 and 1996 was obtained for 32 scenes on the High Plains to coincide with wet and dry years. Additional Landsat 7 data were acquired for 1999 and 2000 primarily for Colorado and Nebraska. As luck would have it, there was no severe drought during the study period 1985-2000. Attention was focused on developing methods for mapping dry vs. green vegetation on sparsely vegetated rangelands in sandy soils, since these were the areas most susceptible to surface reactivation during a drought.

Totally embedded hybrid thin films of carbon nanotubes and silver nanowires as flat homogenous flexible transparent conductors

PubMed Central

Pillai, Suresh Kumar Raman; Wang, Jing; Wang, Yilei; Sk, Md Moniruzzaman; Prakoso, Ari Bimo; Rusli; Chan-Park, Mary B.

2016-01-01

There is a great need for viable alternatives to today’s transparent conductive film using largely indium tin oxide. We report the fabrication of a new type of flexible transparent conductive film using silver nanowires (AgNW) and single-walled carbon nanotube (SWCNT) networks which are fully embedded in a UV curable resin substrate. The hybrid SWCNTs-AgNWs film is relatively flat so that the RMS roughness of the top surface of the film is 3 nm. Addition of SWCNTs networks make the film resistance uniform; without SWCNTs, sheet resistance of the surface composed of just AgNWs in resin varies from 20 Ω/sq to 107 Ω/sq. With addition of SWCNTs embedded in the resin, sheet resistance of the hybrid film is 29 ± 5 Ω/sq and uniform across the 47 mm diameter film discs; further, the optimized film has 85% transparency. Our lamination-transfer UV process doesn’t need solvent for sacrificial substrate removal and leads to good mechanical interlocking of the nano-material networks. Additionally, electrochemical study of the film for supercapacitors application showed an impressive 10 times higher current in cyclic voltammograms compared to the control without SWCNTs. Our fabrication method is simple, cost effective and enables the large-scale fabrication of flat and flexible transparent conductive films. PMID:27929125

Relationships Among Nightly Sleep Quality, Daily Stress, and Daily Affect

PubMed Central

Bergeman, Cindy S.; Whitehead, Brenda R.; Braun, Marcia E.; Payne, Jessic D.

2017-01-01

Abstract Objectives. We explored the prospective, microlevel relationship between nightly sleep quality (SQ) and the subsequent day’s stress on positive (PA) and negative affect (NA) as well as the moderating relationships between nightly SQ, subsequent stress, and subsequent PA on NA. We investigated whether age moderated these relationships. Method. We collected 56 days of sleep, stress, and affect data using daily diary questionnaires (N = 552). We used multilevel modeling to assess relationships at the between- and within-person levels. Results. Daily increases in SQ and decreases in stress interacted to predict higher daily PA and lower daily NA. Better SQ in older adults enhanced the benefits of PA on the stress–NA relationship more during times of low stress, whereas better sleep in younger adults enhanced the benefits of PA more during times of high stress. Between-person effects were stronger predictors of well-being outcomes than within-person variability. Discussion. The combination of good SQ and higher PA buffered the impact of stress on NA. The moderating impact of age suggests that sleep and stress play different roles across adulthood. Targeting intervention and prevention strategies to improve SQ and enhance PA could disrupt the detrimental relationship between daily stress and NA. PMID:26307483

ECG compression using non-recursive wavelet transform with quality control

NASA Astrophysics Data System (ADS)

Liu, Je-Hung; Hung, King-Chu; Wu, Tsung-Ching

2016-09-01

While wavelet-based electrocardiogram (ECG) data compression using scalar quantisation (SQ) yields excellent compression performance, a wavelet's SQ scheme, however, must select a set of multilevel quantisers for each quantisation process. As a result of the properties of multiple-to-one mapping, however, this scheme is not conducive for reconstruction error control. In order to address this problem, this paper presents a single-variable control SQ scheme able to guarantee the reconstruction quality of wavelet-based ECG data compression. Based on the reversible round-off non-recursive discrete periodised wavelet transform (RRO-NRDPWT), the SQ scheme is derived with a three-stage design process that first uses genetic algorithm (GA) for high compression ratio (CR), followed by a quadratic curve fitting for linear distortion control, and the third uses a fuzzy decision-making for minimising data dependency effect and selecting the optimal SQ. The two databases, Physikalisch-Technische Bundesanstalt (PTB) and Massachusetts Institute of Technology (MIT) arrhythmia, are used to evaluate quality control performance. Experimental results show that the design method guarantees a high compression performance SQ scheme with statistically linear distortion. This property can be independent of training data and can facilitate rapid error control.

NASA's Controlled Environment Agriculture Testing for Space Habitats

NASA Technical Reports Server (NTRS)

Wheeler, Raymond M.

2014-01-01

NASA and other space agencies have an interest in using plants for human life support in space. The plants could provide food and O2 for the humans, while removing CO2 and helping purify wastewater. Studies to date have shown that a wide range of crops can be grown in controlled environment conditions envisioned for space. Light is a critical factor both for crop productivity and system power costs, and recent improvements in LEDs make them a preferred lighting option for space. Because space systems would be tightly closed, issues such as ethylene build-up and management must be considered. Ultimately, the costs and reliability of biological life support options must be compared with more conventional life support approaches. Findings to date suggest that about 20-25 sq. meters of crops could supply the O2 for one human, while about 50 sq. meters would be required for food (dietary calories).

Development of molten carbonate fuel cells for power generation

NASA Astrophysics Data System (ADS)

1980-04-01

The broad and comprehensive program included elements of system definition, cell and system modeling, cell component development, cell testing in pure and contaminated environments, and the first stages of technology scale up. Single cells, with active areas of 45 sq cm and 582 sq cm, were operated at 650 C and improved to state of the art levels through the development of cell design concepts and improved electrolyte and electrode components. Performance was shown to degrade by the presence of fuel contaminants, such as sulfur and chlorine, and due to changes in electrode structure. Using conventional hot press fabrication techniques, electrolyte structures up to 20" x 20" were fabricated. Promising approaches were developed for nonhot pressed electrolyte structure fabrication and a promising electrolyte matrix material was identified. This program formed the basis for a long range effort to realize the benefits of molten carbonate fuel cell power plants.

Design and test of a pumped two-phase mounting plate. [for spacecraft thermal control systems

NASA Technical Reports Server (NTRS)

Grote, M. G.; Swanson, T. D.

1985-01-01

The design, fabrication, and testing of the full-scale development unit of a pumped two-phase mounting plate (TPMP) used in advanced two-phase spacecraft thermal control systems are described. The mounting plate is tested with R-11 in the evaporator mode for total heat loads of over 3000 watts and local heat fluxes over 4 W/sq cm, and in the condenser mode with condenser loads from 60 to 400 watts and inlet qualities from 8 to 94 percent. The calculated heat-transfer coefficients are between 0.66 and 1.0 W/sq cm/C and are nearly independent of the flow rate and heat load except at very low heat loads. It is shown that the TPMP can be run with inlet conditions down to 22 C subcooling without any significant gradients in the plate and that it performs well with nonuniform heat fluxes.

Increasing thermal efficiency of solar flat plate collectors

NASA Astrophysics Data System (ADS)

Pona, J.

A study of methods to increase the efficiency of heat transfer in flat plate solar collectors is presented. In order to increase the heat transfer from the absorber plate to the working fluid inside the tubes, turbulent flow was induced by installing baffles within the tubes. The installation of the baffles resulted in a 7 to 12% increase in collector efficiency. Experiments were run on both 1 sq ft and 2 sq ft collectors each fitted with either slotted baffles or tubular baffles. A computer program was run comparing the baffled collector to the standard collector. The results obtained from the computer show that the baffled collectors have a 2.7% increase in life cycle cost (LCC) savings and a 3.6% increase in net cash flow for use in domestic hot water systems, and even greater increases when used in solar heating systems.

Pulsed Laser Illumination of Photovoltaic Cells

NASA Technical Reports Server (NTRS)

Yater, Jane A.; Lowe, Roland; Jenkins, Philip; Landis, Geoffrey A.

1994-01-01

In future space missions, free electron lasers (FEL) may be used to illuminate photovoltaic array receivers to provide remote power. The induction FEL and the radio-frequency (RF) FEL both produce pulsed rather than continuous output. In this work, we investigate cell response to pulsed laser light which simulates the RF FEL format, producing 50 ps pulses at a frequency of 78 MHz. A variety of Si, GaAs, CaSb and CdInSe2 (CIS) solar cells are tested at average incident powers between 4 mW/sq cm and 425 mW/sq cm. The results indicate that if the pulse repetition is high, cell efficiencies are only slightly reduced by using a pulsed laser source compared to constant illumination at the same wavelength. Because the pulse separation is less than or approximately equal to the minority carrier lifetime, the illumination conditions are effectively those of a continuous wave laser. The time dependence of the voltage and current response of the cells are also measured using a sampling oscilloscope equipped with a high frequency voltage probe and current transformer. The frequency response of the cells is weak, with both voltage and current outputs essentially dc in nature. Comparison with previous experiments shows that the RF FEL pulse format yields much more efficient photovoltaic conversion of light than does an induction FEL pulse format.

Superconducting wire manufactured

NASA Astrophysics Data System (ADS)

Fu, Yuexian; Sun, Yue; Xu, Shiming; Peng, Ying

1985-10-01

The MF Nb/Cu Extrusion Tube Method was used to manufacture 3 kg of stable practical MF Nb2Sn composite superconducting wire containing pure Cu(RRR approx. 200)/Ta. The draw state composite wire diameter was 0.56 mm, it contained 11,448 x 2.6 micron Nb core, and the twist distance was 1.5 cm. The composite wire cross-section was pure Cu/Ta/11,448 Nb core/Cu/ 91Sn-Cu; containing 22.8 v. % pure Cu, 13.3 v. % Ta; within the Ta layer to prevent Sn diffusion. The wire was sheathed in nonalkaline glass fiber as an insulating layer. A section of wire weighing 160 g was cut off and coiled it into a small solenoid. After reaction diffusion processing at 675 C/30 and curing by vacuum dipping in paraffin, it was measured in a Nb-Ti backfield of 7.2 T intensity, a current of 129 A was passed through the Nb3Sn solenoid and produced a strength of 2.5 T, the overall magnetic field intensity of the composite magnet reached 9.7 T. At this time, the wire full current density J sub c.w. = 5.2 x 10 to the 4th power A/sq cm; the effective current density J sub c (Nb + Sn - Cu) = 8.2 x 10 to the 4th power A/sq cm.

Materials Needs for Future In-Space Propulsion Systems

NASA Technical Reports Server (NTRS)

Johnson, Les

2006-01-01

NASA's In-Space Propulsion Technology Project is developing the next generation of in-space propulsion systems in support of robotic exploration missions throughout the solar system. The propulsion technologies being developed are non-traditional and have stressing materials performance requirements. Earth-storable bipropellant performance is constrained by temperature limitations of the columbium used in the chamber. Iridium/rhenium (Ir/Re) is now available and has been implemented in initial versions of Earth- Storable rockets with specific impulses about 10 seconds higher than columbium rocket chambers. New chamber fabrication methods that improve process and performance of Ir/Re and other promising material systems are needed. The solar sail is a propellantless propulsion system that gains momentum by reflecting sunlight. The sails need to be very large in area (from 10000 sq m up to 62500 sq m) yet be very lightweight in order to achieve adequate accelerations for realistic mission times. Lightweight materials that can be manufactured in thicknesses of less than 1 micron and that are not harmed by the space environment are desired. Blunt Body Aerocapture uses aerodynamic drag to slow an approaching spacecraft and insert it into a science orbit around any planet or moon with an atmosphere. The spacecraft is enclosed by a rigid aeroshell that protects it from the entry heating and aerodynamic environment. Lightweight, high-temperature structural systems, adhesives, insulators, and ablatives are key components for improving aeroshell efficiencies at heating rates of 1000-2000 W/sq cm and beyond. Inflatable decelerators in the forms of ballutes and inflatable aeroshells will use flexible polymeric thin film materials, high temperature fabrics, and structural adhesives. The inflatable systems will be tightly packaged during cruise and will be inflated prior to entry interface at the destination. Materials must maintain strength and flexibility while packaged at cold temperatures (-100 C) for up to 10 years and then withstand the high temperatures (500 C) encountered during aerocapture.

[French version of screening questionnaire for high-functioning autism or Asperger syndrome in adolescent: Autism Spectrum Quotient, Empathy Quotient and Systemizing Quotient. Protocol and questionnaire translation].

PubMed

Sonié, Sandrine; Kassai, Behrouz; Pirat, Elodie; Masson, Sandrine; Bain, Paul; Robinson, Janine; Reboul, Anne; Wicker, Bruno; Chevallier, Coralie; Beaude-Chervet, Véronique; Deleage, Marie-Hélène; Charvet, Dorothée; Barthélémy, Catherine; Rochet, Thierry; Tatou, Mohamed; Arnaud, Valérie; Manificat, Sabine

2011-04-01

No tools are currently available in France, for the detection of autism without mental retardation (high functioning autism and Asperger syndrome here referred as TED SDI). Use of screening tests by first-line clinicians would allow better detection of children who are likely to display such difficulties and to improve patients' care. In England, 3 questionnaires have been evaluated: Autism Spectrum Quotient (AQ), Empathy Quotient (EQ), and Systemizing Quotient (SQ). This is the translation and evaluation of 3 questionnaires in France for TED SDI and control adolescents. The translation of the questionnaires into French required two simultaneous translations, two back-translations and two consensus meetings. This is a cross-sectional study comparing scores obtained with the three AQ, EQ and SQ questionnaires. These questionnaires were completed by the parents of four groups of adolescents 11-18 years: 100 TED SDI adolescents (50 with IQ ≥ 85 and 50 with 70≤IQ<85), 50 adolescents with another psychiatric disorder (TP) and 200 control adolescents (T). 580 questionnaires have been sent to 40 recruiting centres. By the 28th of February, 2010, 277 completed questionnaires were received completed (TED SDI: 70 (70%); TP: 25 (50%) et T: 182 (91%)). In the control group, 92 girls (mean 14.4±1.7 years) and 66 boys (14.5±1.7 years) were recruited. In the TED SDI group, 4 girls (14.3±2.4 years) and 42 boys (14.5±1.7 years) were recruited. One girl (81) and 6 boys (72.2±7.7) have an IQ between 70 and 85, and 3 girls (95.3±4.2) and 36 boys (102.9±12) have an IQ higher than 85. In the TP group, 9 girls (15.9±1.7 years) and 4 boys (15.8±1.9 years) were recruited. The aim of this study is to make the AQ, EQ and SQ questionnaires available in French for French speaking clinicians. This study will allow a rigorous evaluation of the usefulness of the AQ questionnaire in the screening of TED SDI in adolescents. Copyright © 2010 Elsevier Masson SAS. All rights reserved.

NASA GEOS-3/TRMM Re-analysis: Capturing Observed Tropical Rainfall Variability in Global Analysis for Climate Research

NASA Technical Reports Server (NTRS)

Hou, Arthur Y.

2004-01-01

Understanding climate variability over a wide range of space-time scales requires a comprehensive description of the earth system. Global analyses produced by a fixed assimilation system (i.e., re-analyses) - as their quality continues to improve - have the potential of providing a vital tool for meeting this challenge. But at the present time, the usefulness of re-analyses is limited by uncertainties in such basic fields as clouds, precipitation, and evaporation - especially in the tropics, where observations are relatively sparse. Analyses of the tropics have long been shown to be sensitive to. the treatment of cloud precipitation processes, which remains a major source of uncertainty in current models. Yet, for many climate studies it is crucial that analyses can accurately reproduce the observed rainfall intensity and variability since a small error of 1 mm/d in surface rain translates into an error of approx. 30 W/sq m in energy (latent heat) flux. Currently, discrepancies between the observed and analyzed monthly-mean rain rates averaged to 100 km x 100 km resolution can exceed 4 mm/d (or 120 W/sq m ), compared to uncertainties in surface radiative fluxes of approx. 10-20 W/sq m . Improving precipitation in analyses would reduce a major source of uncertainty in the global energy budget. Uncertainties in tropical precipitation have also been a major impediment in understanding how the tropics interact with other regions, including the remote response to El Nino/Southern Oscillation (ENSO) variability on interannual time scales, the influence of Madden-Julian Oscillation (MJO) and monsoons on intraseasonal time scales. A global analysis that can replicate the observed precipitation variability together with physically consistent estimates of other atmospheric variables provides the key to breaking this roadblock. NASA Goddard Space Flight Center has been exploring the use of satellite-based microwave rainfall measurements in improving global analyses and has recently produced a multi-year, 1 x 1 TRMM re-analysis , which assimilates 6-hourly TMI and SSM/I surface rain rates over tropical oceans using a ID variational continuous assimilation (VCA) procedure in the GEOS-3 global data assimilation system. The analysis period extends from 1 November 1997 through 3 1 December 2002. The goal is to produce a multi-year global analysis that is dynamically consistent with available tropical precipitation observations for the community to assess its utility in climate applications and identify areas for further improvements. A distinct feature of the GEOS-3RRMh4 re-analysis is that its precipitation analysis is not derived from a short-term forecast (as done in most operational systems) but is given by a time- continuous model integration constrained by precipitation observations within a 6-h analysis window, while the wind, temperature, and pressure fields are allowed to directly respond to the improved precipitation and associated latent heating structures within the same analysis window. In this talk, I will assess the impact VCA precipitation assimilation on analyses of climate signals ranging from a few weeks to interannual time scales and compare results against other operational and reanalysis products.

Relation of morphology of electrodeposited zinc to ion concentration profile

NASA Technical Reports Server (NTRS)

May, C. E.; Kautz, H. E.; Sabo, B. B.

1977-01-01

The morphology of electrodeposited zinc was studied with special attention to the ion concentration profile. The initial concentrations were 9M hydroxide ion and 1.21M zincate. Current densities were 6.4 to 64 mA/sq cm. Experiments were run with a horizontal cathode which was observed in situ using a microscope. The morphology of the zinc deposit was found to be a function of time as well as current density; roughly, the log of the transition time from mossy to large crystalline type deposit is inversely proportional to current density. Probe electrodes indicated that the electrolyte in the cathode chamber was mixed by self inducted convection. However, relatively large concentration gradients of the involved species existed across the boundary layer of the cathode. Analysis of the data suggests that the morphology converts from mossy to large crystalline when the hydroxide activity on the cathode surface exceeds about 12 M. Other experiments show that the pulse discharge technique had no effect on the morphology in the system where the bulk concentration of the electrolyte was kept homogeneous via self induced convection.

Magnetobraking: Use of tether electrodynamic drag for Earth return from Mars

NASA Technical Reports Server (NTRS)

Landis, Geoffrey A.

1994-01-01

It has often been proposed that a vehicle returning from Mars will use aerobraking in the Earth's atmosphere to dissipate hyperbolic excess velocity to capture into Earth orbit. Here a different system for dissipating excess velocity without expenditure of reaction mass, magnetobraking, is proposed. Magnetobraking uses the force on an electrodynamic tether in the Earth's magnetic field to produce thrust. An electrodynamic tether is deployed from the spacecraft as it approaches the Earth. The Earth's magnetic field produces a force on electrical current in the tether. If the tether is oriented perpendicularly to the Earth's magnetic field and to the direction of motion of the spacecraft, force produced by the Earth's magnetic field can be used to either brake or accelerate the spacecraft without expenditure of reaction mass. The peak acceleration on the Mars return is 0.007 m/sq sec, and the amount of braking possible is dependent on the density and current-carrying capacity of the tether, but is independent of length. A superconducting tether is required. The required critical current is shown to be within the range of superconducting technology now available in the laboratory.

High current density sheet-like electron beam generator

NASA Astrophysics Data System (ADS)

Chow-Miller, Cora; Korevaar, Eric; Schuster, John

Sheet electron beams are very desirable for coupling to the evanescent waves in small millimeter wave slow-wave circuits to achieve higher powers. In particular, they are critical for operation of the free-electron-laser-like Orotron. The program was a systematic effort to establish a solid technology base for such a sheet-like electron emitter system that will facilitate the detailed studies of beam propagation stability. Specifically, the effort involved the design and test of a novel electron gun using Lanthanum hexaboride (LaB6) as the thermionic cathode material. Three sets of experiments were performed to measure beam propagation as a function of collector current, beam voltage, and heating power. The design demonstrated its reliability by delivering 386.5 hours of operation throughout the weeks of experimentation. In addition, the cathode survived two venting and pump down cycles without being poisoned or losing its emission characteristics. A current density of 10.7 A/sq cm. was measured while operating at 50 W of ohmic heating power. Preliminary results indicate that the nearby presence of a metal plate can stabilize the beam.

Electromagnetic interference assessment of an ion drive electric propulsion system

NASA Technical Reports Server (NTRS)

Whittlesey, A. C.

1979-01-01

The electromagnetic interference (EMI) form elements of an ion drive electric propulsion system was analyzed, and the effects of EMI interaction with a typical interplanetary spacecraft engineering and scientific subsystems were predicted. SEMCAP, a computerized electromagnetic compatibility assessment code, was used to analyze the impact of EMI noise sources on 65 engineering/telemetry circuits and 48 plasma wave and planetary radio astronomy channels measuring over the range of 100 Hz to 40 MHz in a spacecraft of the Voyager type; manual methods were used to evaluate electrostatics, magnetics, and communications effects. Results indicate that some conducted and radiated spectra are in excess of electromagnetic compatibility specification limits; direct design changes may be required for filtering and shielding of thrust system elements. The worst source of broadband radiated noise appears to be the power processor. The magnetic field necessary to thruster operation is equivalent to about 18 amp-sq m per amp of beam current at right angles to the axis caused by the neutralizer/plume loop.

Development of a screening questionnaire for DSM-5 intermittent explosive disorder (IED-SQ).

PubMed

Coccaro, Emil F; Berman, Mitchell E; McCloskey, Michael S

2017-04-01

This study was designed to develop and test a screening approach to identify individuals with DSM-5 Intermittent Explosive Disorder (IED), a disorder of recurrent, problematic, impulsive aggression. A screening approach to diagnose DSM-5 IED (IED-SQ) was developed by combining items related to life history of aggression and items related to the DSM-5 diagnostic criteria for IED. In study 1, the IED-SQ was studied in 72 adult participants; 33 that met DSM-5 criteria for lifetime IED and 39 that did not. In study 2, the IED-SQ was given to 740 undergraduates at a US university. Measures of aggression and anger expression and anger control were assessed in both studies. In study 1, the IED-SQ demonstrated strong concordance with the best estimate diagnoses (Kappa =.80) for lifetime IED by DSM-5 criteria and good test-retest reliability (kappa =0.71). In study 2, the IED-SQ identified 4.3% of the undergraduate sample as meeting DSM-5 criteria for lifetime IED, a rate comparable to that in recent epidemiological studies. Participants identified as meeting DSM-5 criteria for lifetime IED, in both studies, had higher aggression scores, and higher anger expression, and lower anger control scores, compared to participants that did not meet DSM-5 criteria for lifetime IED. These data suggest that the IED-SQ is a useful screening tool that can quickly identify the presence of IED by DSM-5 criteria in adults. Copyright © 2016 Elsevier Inc. All rights reserved.

Thromboxane plays a role in postprandial jejunal oxygen uptake and capillary exchange.

PubMed

Alemayehu, A; Chou, C C

1990-09-01

The effects of a thromboxane A2 (TxA2)-endoperoxide receptor antagonist, SQ 29548, on jejunal blood flow, oxygen uptake, and capillary filtration coefficient (Kfc) were determined in anesthetized dogs under resting conditions and during the presence of predigested food in the jejunal lumen in three series of experiments. In series 1, 2.0 micrograms intra-arterial administration of SQ 29548 was found to abolish completely the vasoconstrictor action of graded doses (0.05-2.0 micrograms) of intra-arterial injection of a TxA2-endoperoxide analogue, U44069. SQ 29548 (2.0 micrograms ia) per se did not significantly alter resting jejunal blood flow, oxygen uptake, capillary pressure, or Kfc. Before SQ 29548, placement of food plus bile into the jejunal lumen increased blood flow +42 +/- 9%, oxygen uptake +28 +/- 7%, and Kfc +24 +/- 6%. After SQ 29548, the food placement increased blood flow +37 +/- 8%, oxygen uptake +52 +/- 11%, and Kfc +63 +/- 20%. The food-induced increases in oxygen uptake and Kfc after SQ 29548 were significantly greater than those induced before the blocking of TxA2-endoperoxide receptors by SQ 29548. Our study indicates that endogenous thromboxane does not play a role in regulating jejunal blood flow, capillary filtration, and oxygen uptake under resting conditions. However, it plays a role in limiting the food-induced increases in jejunal oxygen uptake and capillary exchange capacity without influencing the food-induced hyperemia.

Descriptive survey and Salmonella surveillance of pastured poultry layer farms in California.

PubMed

Dailey, Naomi; Niemeier, Deb; Elkhoraibi, Carine; Sentíes-Cué, C Gabriel; Pitesky, Maurice

2017-04-01

While pasture-raised poultry comprises a small portion of the commercial poultry industry in North America, these alternative rearing systems have become increasingly popular. As such, it is critical to improve our understanding of husbandry practices and prevalence of zoonotic and epizoonotic diseases in these systems. This research reviews the results of a survey sent to 82 commercial pastured poultry farms in California. While the survey response was low (13.4%), it was enhanced by detailed in-person interviews and farm visits. In addition, we conducted drag swabs for Salmonella Enteritidis. On average, farms utilized 12.3% of their total farmland for pastured poultry operations, which often coexisted with other livestock (45%), touch crops (27%), and non-touch crops (45%). While the mean (44.6 sq. ft./hen) and median (22.2 sq. ft./hen) pasture stocking densities were within auditing guidelines, the mean (1.2 sq. ft./hen) and median (0.5 sq. ft./hen) coop stocking densities were below the pending USDA (2016) guidelines recommended in 7 CFR Part 205. Drag swab results showed the presence of Salmonella Enteritidis (SE) in the environment of one of the 11 farms (9.1%). In addition, Salmonella Pullorum (SP) whole blood agglutination tests were used to understand the prevalence of Salmonella spp. in laying hens within the studied farms. Results showed the presence of antibodies in flocks at six of the seven non-SE vaccinated farms, with a mean on-farm prevalence of 25.6% in laying hens. Logistic regression was used to determine risk factors for Group D Salmonella exposure in non-vaccinated flocks, using the SP blood agglutination data as the dependent variable and the survey questions as the independent variables. Statistically significant (P < 0.05) risk factors included exposed wire floors and flock size. These results improve our understanding of Salmonella prevalence and husbandry practices on commercial pastured poultry farms in California. © 2016 Poultry Science Association Inc.

Fluence Uniformity Measurements in an Electron Accelerator Used for Irradiation of Extended Area Solar Cells and Electronic Circuits for Space Applications

NASA Technical Reports Server (NTRS)

Uribe, Roberto M.; Filppi, Ed; Zhang, Shubo

2007-01-01

It is common to have liquid crystal displays and electronic circuit boards with area sizes of the order of 20x20 sq cm on board of satellites and space vehicles. Usually irradiating them at different fluence values assesses the radiation damage in these types of devices. As a result, there is a need for a radiation source with large spatial fluence uniformity for the study of the damage by radiation from space in those devices. Kent State University s Program on Electron Beam Technology has access to an electron accelerator used for both research and industrial applications. The electron accelerator produces electrons with energies in the interval from 1 to 5 MeV and a maximum beam power of 150 kW. At such high power levels, the electron beam is continuously scanned back and forth in one dimension in order to provide uniform irradiation and to prevent damage to the sample. This allows for the uniform irradiation of samples with an area of up to 1.32 sq m. This accelerator has been used in the past for the study of radiation damage in solar cells (1). However in order to irradiate extended area solar cells there was a need to measure the uniformity of the irradiation zone in terms of fluence. In this paper the methodology to measure the fluence uniformity on a sample handling system (linear motion system), used for the irradiation of research samples, along the irradiation zone of the above-mentioned facility is described and the results presented. We also illustrate the use of the electron accelerator for the irradiation of large area solar cells (of the order of 156 sq cm) and include in this paper the electrical characterization of these types of solar cells irradiated with 5 MeV electrons to a total fluence of 2.6 x 10(exp 15) e/sq cm.

Fabrication end Deployment Testing of Meter Solar Sail Quadrants for a Scaleable Square Solar Sail Ground Test System

NASA Technical Reports Server (NTRS)

Laue, Greg; Case, David; Moore, Jim

2005-01-01

In order for solar sail propulsion technologies to be considered as a viable option for a wide range of near term practical missions a predictable, stable, reliable, manufactureable, scaleable, and cost effective system must be developed and tested first on earth and then on orbit. The design and development of a Scaleable Square Solar Sail System (S^4) is well underway a t AEC-Able Engineering Co. Inc., and the design and production of the Solar Sails for this system is being carried out by SRS Technologies. In April and May of 2004 a single quadrant 10-meter system was tested at NASA LARC's vacuum chamber and a four quadrant 20-meter system has been designed and built for deployment and testing in the Spring of 2005 at NASA/Glenn Research Center's Plumb Brook Facility. SRS has developed an effective and efficient design for triangular sail quadrants that are supported are three points and provide a flat reflective surface with a high fill factor. This sail design is robust enough for deployments in a one atmosphere, one gravity environment and incorporates several advanced features including adhesiveless seaming of membrane strips, compliant edge borders to allow for film membrane cord strain mismatch without causing wrinkling and low mass (3% of total sail mass) ripstop. This paper will outline the sail design and fabrication process, the lessons learned and the resulting mature production, packaging and deployment processes that have been developed. It will also highlight the scalability of the equipment and processes that were developed to fabricate and package the sails. Based on recent experience, SRS is confidant that flight worthy solar sails in the 40-120-meter size range with areal density in the 4-5g/sq m (sail minus structure) range can be produced with existing technology. Additional film production research will lead to further reductions in film thickness to less than 1 micron enabling production of sails with areal densities as low as 20 g/sq m using the current design resulting in a system areal density of as low as 5.3g/sq m. These areal densities are low enough to allow nearly all of the Solar Sail missions that have been proposed by the scientific community and the fundamental technology required to produce these sails has been demonstrated on the ground test sails that have recently been built. These demonstrations have shown that the technology is mature enough to build sails needed to support critical science missions. Solar Sails will be an enabling technology for NASA's Vision for Space Exploration by allowing communication satellite orbits that can maintain continuous communication with the polar regions of the Moon and Mars and to support solar weather monitoring to provide early warning of solar flares and storms that could threaten the safety of astronauts and other spacecraft.

Carnivorous plants in Micronesia

Treesearch

Robert R. Ziemer

1988-01-01

Micronesia encompasses about 2,100 islands scattered over some 12 million sq km of the central Pacific between Hawaii and the Philippines. Only about 125 of these small islands are inhabited. The total land area of Micronesia is less than 3,200 sq km, about the size of the state of Rhode Island. The largest island is Guam, with an area of about 540 sq km. There are...

Brief Report: Development of the Adolescent Empathy and Systemizing Quotients

ERIC Educational Resources Information Center

Auyeung, Bonnie; Allison, Carrie; Wheelwright, Sally; Baron-Cohen, Simon

2012-01-01

Adolescent versions of the Empathy Quotient (EQ) and Systemizing Quotient (SQ) were developed and administered to n = 1,030 parents of typically developing adolescents, aged 12-16 years. Both measures showed good test-retest reliability and high internal consistency. Girls scored significantly higher on the EQ, and boys scored significantly higher…

Development of high temperature gallium phosphide rectifiers

NASA Technical Reports Server (NTRS)

Craford, M. G.; Keune, D. L.

1972-01-01

Large area high performance, GaP rectifiers were fabricated by means of Zn diffusion into vapor phase epitaxial GaP. Devices with an active area of 0.01 sq cm typically exhibit forward voltages of 3 volts for a bias current of 1 ampere and have reverse breakdown voltages of 300 volts for temperatures from 27 C to 400 C. Typical device reverse saturation current at a reverse bias of 150 volts is less than 10 to the minus 9th power amp at 27 C and less than 0.000050 amp at 400 C.

Operational performance of the photovoltaic-powered grain mill and water pump at Tangaye, Burkina Faso (formerly Upper Volta)

NASA Technical Reports Server (NTRS)

Martz, J. E.; Roberts, A. F.

1985-01-01

A photovoltaic (PV) system powering a grain mill and water pump was installed in the remote African village of Tangaye, Burkina Faso (formerly Upper Volta) under the sponsorship of the U.S. Agency for International Development (AID) and by the National Aeronautics and Space Administration (NASA) Lewis Research Center (LeRC) in early 1979. The presence reports covers the second two years of operation from April 1981 through June 1983. During this time, the grain mill and water pump were operational 96 and 88 percent of the time respectively, and the PV system generated sufficient electricity to enable the grinding of about 111 metric tons of finely ground flow and the pumping of over 5000 cm sq of water from the 10 m deep well. The report includes a description of the current configuration of the system, a review of system performance, a discussion of the socioeconomic impact of the system on the villagers and a summary of results and conclusions covering the entire four-year period.

Operational performance of the photovoltaic-powered grain mill and water pump at Tangaye, Burkina Faso (formerly Upper Volta). Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martz, J.E.; Roberts, A.F.

1985-03-01

A photovoltaic (PV) system powering a grain mill and water pump was installed in the remote African village of Tangaye, Burkina Faso (formerly Upper Volta) under the sponsorship of the U.S. Agency for International Development (AID) and by the National Aeronautics and Space Administration (NASA) Lewis Research Center (LeRC) in early 1979. The presence reports covers the second two years of operation from April 1981 through June 1983. During this time, the grain mill and water pump were operational 96 and 88 percent of the time respectively, and the PV system generated sufficient electricity to enable the grinding of aboutmore » 111 metric tons of finely ground flow and the pumping of over 5000 cm sq of water from the 10 m deep well. The report includes a description of the current configuration of the system, a review of system performance, a discussion of the socioeconomic impact of the system on the villagers and a summary of results and conclusions covering the entire four-year period.« less

The alkali metal thermoelectric converter /AMTEC/ - A new direct energy conversion technology for aerospace power

NASA Technical Reports Server (NTRS)

Bankston, C. P.; Cole, T.; Jones, R.; Ewell, R.

1982-01-01

A thermally regenerative electrochemical device for the direct conversion of heat to electrical energy, the alkali metal thermoelectric converter (AMTEC), is characterized by potential efficiencies on the order of 15-40% and possesses no moving parts, making it a candidate for space power system applications. Device conversion efficiency is projected on the basis of experimental voltage vs current curves exhibiting power densities of 0.7 W/sq cm and measured electrode efficiencies of up to 40%. Preliminary radiative heat transfer measurements presented may be used in an investigation of methods for the reduction of AMTEC parasitic radiation losses. AMTEC assumes heat input and rejection temperatures of 900-1300 K and 400-800 K, respectively. The working fluid is liquid sodium, and the porous electrode employed is of molybdenum.

Single Wall Carbon Nanotube-polymer Solar Cells

NASA Technical Reports Server (NTRS)

Bailey, Sheila G.; Castro, Stephanie L.; Landi, Brian J.; Gennett, Thomas; Raffaelle, Ryne P.

2005-01-01

Investigation of single wall carbon nanotube (SWNT)-polymer solar cells has been conducted towards developing alternative lightweight, flexible devices for space power applications. Photovoltaic devices were constructed with regioregular poly(3-octylthiophene)-(P3OT) and purified, >95% w/w, laser-generated SWNTs. The P3OT composites were deposited on ITO-coated polyethylene terapthalate (PET) and I-V characterization was performed under simulated AM0 illumination. Fabricated devices for the 1.0% w/w SWNT-P3OT composites showed a photoresponse with an open-circuit voltage (V(sub oc)) of 0.98 V and a short-circuit current density (I(sub sc)) of 0.12 mA/sq cm. Optimization of carrier transport within these novel photovoltaic systems is proposed, specifically development of nanostructure-SWNT complexes to enhance exciton dissociation.

Ultrahigh-current-density metal-ion implantation and diamondlike-hydrocarbon films for tribological applications

NASA Astrophysics Data System (ADS)

Wilbur, P. J.

1993-09-01

The metal-ion-implantation system used to implant metals into substrates are described. The metal vapor required for operation is supplied by drawing sufficient electron current from the plasma discharge to an anode-potential crucible so a solid, pure metal placed in the crucible will be heated to the point of vaporization. The ion-producing, plasma discharge is initiated within a graphite-ion-source body, which operates at high temperature, by using an argon flow that is turned off once the metal vapor is present. Extraction of ion beams several cm in diameter at current densities ranging to several hundred micro-A/sq cm on a target 50 cm downstream of the ion source were demonstrated using Mg, Ag, Cr, Cu, Si, Ti, V, B, and Zr. These metals were implanted into over 100 substrates (discs, pins, flats, wires). A model describing thermal stresses induced in materials (e.g. ceramic plates) during high-current-density implantation is presented. Tribological and microstructural characteristics of iron and 304-stainless-steel samples implanted with Ti or B are examined. Diamondlike-hydrocarbon coatings were applied to steel surfaces and found to exhibit good tribological performance.

A simple model of proton damage in GaAs solar cells

NASA Technical Reports Server (NTRS)

Wilson, J. W.; Walker, G. H.; Outlaw, R. A.

1982-01-01

A simple proton damage model for GaAs solar cells is derived and compared to experimental values of change in short circuit currents. The recombination cross section associated with the defects was determined from the experimental comparison to be approximately 1.2 x 10 to the -13th power sq cm in fair agreement with values determined from the deep level transient spectroscopy technique.

Development of a mercuric iodide solid state spectrometer for X-ray astronomy

NASA Technical Reports Server (NTRS)

Vallerga, J.

1983-01-01

Mercuric iodide detectors, experimental development for astronomical use, X ray observations of the 1980 Cygnus X-1 High State, astronomical had X ray detectors in current use, detector development, balloon flight of large area (1500 sq cm) Phoswich detectors, had X ray telescope design, shielded mercuric iodide background measurement, Monte Carlo analysis, measurements with a shielded mercuric iodide detector are discussed.

Evidence of gravity wave-tidal interaction observed near the summer mesopause at Poker Flat, Alaska

NASA Technical Reports Server (NTRS)

Wang, Ding-Yi; Fritts, David C.

1991-01-01

An analysis of gravity wave-tidal interaction observed near the mesopause by the MST radar at Poker Flat in July of 1986 is presented. The observations revealed daily mean wind maxima of about 60 m/sec westward and 20 m/sec southward with daily mean momentum fluxes, contributed by gravity waves with periods less than 1 hour of 4-5 sq m/sec sq eastward and 1-2 sq m/sec sq northward. Considerable hourly height variability was found to exist for both winds and momentum fluxes. A significant modulation of the fluxes by tidal winds was observed, characterized by out-of-phase correlations over a number of heights.

Very heavy solar cosmic rays: Energy spectrum and implications for lunar erosion

NASA Technical Reports Server (NTRS)

Fleischer, R. L.; Hart, H. R., Jr.; Comstock, G. M.

1972-01-01

Particle tracks were investigated in the glass plate of a neutral density (clear flint) optical filter housed in the Surveyor 3 TV camera but exposed directly to space. The track density vs depth curve was determined and descends sharply from approximately 2.6 million tracks/sq cm at a depth of 3.6 mg/sq cm to about 35/sq cm at 700 mg/sq cm. Several tracks were of V-shapes characteristic of high energy induced fission. The erosion rate on the moon due to solar wind ions was determined from the energy spectrum, and was found to be low (0 to 2 x 10 to the minus 8th power cm/yr).

Radiative Forcing Due to Major Aerosol Emitting Sectors in China and India

NASA Technical Reports Server (NTRS)

Streets, David G.; Shindell, Drew Todd; Lu, Zifeng; Faluvegi, Greg

2013-01-01

Understanding the radiative forcing caused by anthropogenic aerosol sources is essential for making effective emission control decisions to mitigate climate change. We examined the net direct plus indirect radiative forcing caused by carbonaceous aerosol and sulfur emissions in key sectors of China and India using the GISS-E2 chemistry-climate model. Diesel trucks and buses (67 mW/ sq. m) and residential biofuel combustion (52 mW/ sq. m) in India have the largest global mean, annual average forcings due mainly to the direct and indirect effects of BC. Emissions from these two sectors in China have near-zero net global forcings. Coal-fired power plants in both countries exert a negative forcing of about -30 mW/ sq. m from production of sulfate. Aerosol forcings are largest locally, with direct forcings due to residential biofuel combustion of 580 mW/ sq. m over India and 416 mW/ sq. m over China, but they extend as far as North America, Europe, and the Arctic

Field-aligned currents and the auroral electrojet

NASA Technical Reports Server (NTRS)

Cahill, L. J.; Potter, W. E.; Kintner, P. M.; Arnoldy, R. L.; Choy, L. W.

1974-01-01

A Nike Tomahawk with fields and particles payload was launched on Nov. 18, 1970, over a strong westward electrojet current and auroral forms moving rapidly to the east. Electron fluxes moving up and down the magnetic field lines were measured. Upward-moving electrons below 1-keV energy were dominant and were equivalent to a net downward electric current that fluctuated between .2 and .6 microamp/sq m during the flight above 130 km. As the rocket traversed this broad region of downward electric current over and to the north of the auroral forms, the horizontal electric field slowly rotated from east to west. The magnetic measurements indicate that the westward electrojet was a horizontal sheet of current several hundred kilometers in north-south extent.

Difference of Morphology and Immunophenotype between Central and Peripheral Squamous Cell Carcinomas of the Lung

PubMed Central

Hayashi, Tomayoshi; Sano, Hisao; Egashira, Ryoko; Tabata, Kazuhiro; Tanaka, Tomonori; Kashima, Yukio; Nunomura, Sayuri

2013-01-01

Background. Recent agents, that is, pemetrexed and bevacizumab, have shown reproductive negative association between squamous histology. According to these agents' effectiveness, ruling out of the squamous histology is a significant issue for surgical pathologists. Several articles have proposed the distinction of peripheral type from central type of squamous cell carcinoma (SqCC) due to its similarity to adenocarcinoma, although little evidence to support the difference between these two types was published. In this study, we compared the clinicopathologic findings of central and peripheral pulmonary SqCCs. Material and Methods. 15 central and 35 peripheral types of SqCC from 2005 to 2010 were examined. Twelve morphological features were scored based on their intensity in the original H&E slides, and then, tissue microarray holding triplicated cores from 43 cases was immunohistochemically examined for cytokeratin (CK)7, CK14, TTF-1, Napsin A, p63, CK34βE12, CK5/6, and p53. Result. Most of the histological findings did not separate central and peripheral SqCCs; only the presence of emphysema, interstitial fibrosis, and entrapped pneumocytes inside the tumor showed statistic predominance in peripheral SqCC. This is the first immunophenotypic research in the central and peripheral types of SqCC. PMID:24069587

Critical current densities in superconducting Y-Ba-Cu-O prepared by chelating method

NASA Astrophysics Data System (ADS)

Fujisawa, Tadashi; Okuyama, Katsuro; Ohshima, Shigetoshi; Takagi, Akira

1990-10-01

The IDA, NTA, HEDTA, EDTA, TTHA, and DTPA chelating agents have been used to prepare the Y-Ba-Cu-O compounds whose critical current is presently investigated. It is noted that the precursor YBCO prepared from large stability-constant metal complexes (HEDTA, EDTA, DTPA, and TTHA) exhibited very fine and homogeneous particles. The critical current density of a 1 x 4 x 15 mm block of YBCO sintered at 880-910 C for 24 h and subsequently annealed at 500 C in an O2 flow was approximately 500 A/sq cm at 77 K, in zero magnetic field.

Shielding and flux trapping properties of high temperature superconductors in the shape of hollow cylinders

NASA Technical Reports Server (NTRS)

Israelsson, U. E.; Strayer, D. M.

1991-01-01

Allowing for a field-dependent critical current density, the authors calculate the magnetic field that can be supported by hollow cylinders of varying wall thickness. An adiabatically stable field of 1.0 T can be shielded by or trapped in a cylinder with a wall thickness of 0.4 cm if the critical current density varies linearly with magnetic field and has a value of 104 A/sq cm at a field of 1.0 T. Such a current density appears to be within reach of present state-of-the-art melt-processed YBa2Cu3O7 (123) materials.

Theoretical study of the effect of ionospheric return currents on the electron temperature

NASA Technical Reports Server (NTRS)

Schunk, R. W.; Sojka, J. J.; Bowline, M. D.

1987-01-01

A time-dependent, three-dimensional model of the high-altitude ionosphere is presently used to study the effects of field-aligned ionospheric return currents on auroral electron temperatures for different seasonal and solar cycle conditions, as well as for different upper boundary heat fluxes. The average, large scale, return current densities, which are a few microamps/sq m, are too small to affect auroral electron temperatures. The thermoelectric effect exhibits a pronounced solar cycle and seasonal dependence, and its heat transport corresponds to an upward flow of electron energy which can be either a source or sink of electron energy depending on altitude and geophysical conditions.

Signal-to-noise ratio for the wide field-planetary camera of the Space Telescope

NASA Technical Reports Server (NTRS)

Zissa, D. E.

1984-01-01

Signal-to-noise ratios for the Wide Field Camera and Planetary Camera of the Space Telescope were calculated as a function of integration time. Models of the optical systems and CCD detector arrays were used with a 27th visual magnitude point source and a 25th visual magnitude per arc-sq. second extended source. A 23rd visual magnitude per arc-sq. second background was assumed. The models predicted signal-to-noise ratios of 10 within 4 hours for the point source centered on a signal pixel. Signal-to-noise ratios approaching 10 are estimated for approximately 0.25 x 0.25 arc-second areas within the extended source after 10 hours integration.

Four Interstellar Dust Candidates from the Stardust Interstellar Dust Collector

NASA Technical Reports Server (NTRS)

Westphal, A. J.; Allen, C.; Bajt, S.; Bechtel, H. A.; Borg, J.; Brenker, F.; Bridges, J.; Brownlee, D. E.; Burchell, M.; Burghammer, M.;

PICA Variants with Improved Mechanical Properties

NASA Technical Reports Server (NTRS)

Thornton, Jeremy; Ghandehari, Ehson M.; Fan, Wenhong; Stackpoole, Margaret; Chavez-Garcia, Jose

2011-01-01

Phenolic Impregnated Carbon Ablator (PICA) is a member of the family of Lightweight Ceramic Ablators (LCAs) and was developed at NASA Ames Research Center as a thermal protection system (TPS) material for the Stardust mission probe that entered the Earth s atmosphere faster than any other probe or vehicle to date. PICA, carbon fiberform base and phenolic polymer, shows excellent thermal insulative properties at heating rates from about 250 W/sq cm to 1000 W/sq cm. The density of standard PICA - 0.26 g/cu cm to 0.28 g/cu cm - can be changed by changing the concentration of the phenolic resin. By adding polymers to the phenolic resin before curing it is possible to significantly improve the mechanical properties of PICA without significantly increasing the density.

Carbon dioxide and water exchange rates by a wheat crop in NASA's biomass production chamber: Results from an 86-day study (January to April 1989)

NASA Technical Reports Server (NTRS)

Wheeler, R. M.; Sager, J. C.

1990-01-01

Gas exchange measurements were taken for a 20 sq m wheat stand grown from seed to harvest in NASA's Biomass Production Chamber. Respiration of the wheat stand caused the CO2 concentrations to rise an average of 440 ppm during the 4-h dark period each day, or 7.2 umol/sq m/sec. Dark period respiration was sensitive to temperature changes and could be increased 70 to 75 percent by raising the temperature from 16 C to 24 C. Stand photosynthesis (measured from the rate of CO2 drawdown immediately after the lights came on each day) peaked at 27 umol/sq m/sec at 25 days after planting and averaged 15 umol/sq m/sec throughout the study. By combining the average light period photosynthesis and average dark period respiration, a net of 860 g or 470 liters of CO2 were fixed per day. Stand photosynthetic rates showed a linear increase with increasing irradiance (750 umol/sq m/sec PPF the highest level tested), with an average light compensation point after day 30 of 190 umol/sq m/sec. Stand photosynthesis decreased slightly when CO2 levels were decreased from 2200 to 800 ppm, but dropped sharply when CO2 was decreased below 700 to 800 ppm. Water production from stand transpiration peaked at 120 L/day near 25 days and averaged about 90 L/day, or 4.5 L/sq m/day throughout the study.

Telecommunications in cometary environments

NASA Technical Reports Server (NTRS)

Flock, W. L.

1981-01-01

Propagation effects on telecommunications in a cometary environment include those due to dust, the inhomogeneous plasma of the coma and tail, and ionization generated by impact of neutral molecules and dust on the spacecraft. Attenuation caused by dust particles is estimated to be on the order of 10 to the minus 5th power dB for the Halley Intercept Mission. Ionization generated by impact on the spacecraft is estimated to result in an electron content of 10 to the 12th power to 10 to the 13th power el/sq meters (3 eV electrons) along the telecommunications path. An estimate of the electron content due to Comet Halley itself is 10 to the 16th power to 10 to the 17th power el/sq meters, compared to a content of 10 to the 16th power to 10 to the 18th power el/sq meters for the Earth's ionosphere and 10 to the 17th power to 10 to the 18th power el/sq meters for the interplanetary medium. The electron content of the plasma near Comet Halley will cause excess range delay, and a Doppler shift of the signal from the spacecraft will occur in propagation to the rate of change of the path electron content. It is recommended that S and X down-link frequencies by employed to monitor the path electron content and amplitude scintillation and spectral broadening of the received signals. These measurements will provide a quantitative base of knowledge that will be valuable for radio science and telecommunications system design purposes.

Sequential simulation (SqS) of clinical pathways: a tool for public and patient engagement in point-of-care diagnostics

PubMed Central

Huddy, Jeremy R; Weldon, Sharon-Marie; Ralhan, Shvaita; Painter, Tim; Hanna, George B; Kneebone, Roger; Bello, Fernando

2016-01-01

Objectives Public and patient engagement (PPE) is fundamental to healthcare research. To facilitate effective engagement in novel point-of-care tests (POCTs), the test and downstream consequences of the result need to be considered. Sequential simulation (SqS) is a tool to represent patient journeys and the effects of intervention at each and subsequent stages. This case study presents a process evaluation of SqS as a tool for PPE in the development of a volatile organic compound-based breath test POCT for the diagnosis of oesophagogastric (OG) cancer. Setting Three 3-hour workshops in central London. Participants 38 members of public attended a workshop, 26 (68%) had no prior experience of the OG cancer diagnostic pathway. Interventions Clinical pathway SqS was developed from a storyboard of a patient, played by an actor, noticing symptoms of oesophageal cancer and following a typical diagnostic pathway. The proposed breath testing strategy was then introduced and incorporated into a second SqS to demonstrate pathway impact. Facilitated group discussions followed each SqS. Primary and secondary outcome measures Evaluation was conducted through pre-event and postevent questionnaires, field notes and analysis of audiovisual recordings. Results 38 participants attended a workshop. All participants agreed they were able to contribute to discussions and like the idea of an OG cancer breath test. Five themes emerged related to the proposed new breath test including awareness of OG cancer, barriers to testing and diagnosis, design of new test device, new clinical pathway and placement of test device. 3 themes emerged related to the use of SqS: participatory engagement, simulation and empathetic engagement, and why participants attended. Conclusions SqS facilitated a shared immersive experience for participants and researchers that led to the coconstruction of knowledge that will guide future research activities and be of value to stakeholders concerned with the invention and adoption of POCT. PMID:27625053

Annual Cycles of Multiyear Sea Ice Coverage of the Arctic Ocean: 1999-2003

NASA Technical Reports Server (NTRS)

Kwok, R.

2004-01-01

For the years 1999-2003, we estimate the time-varying perennial ice zone (PIZ) coverage and construct the annual cycles of multiyear (MY, including second year) ice coverage of the Arctic Ocean using QuikSCAT backscatter, MY fractions from RADARSAT, and the record of ice export from satellite passive microwave observations. An area balance approach extends the winter MY coverage from QuikSCAT to the remainder of the year. From these estimates, the coverage of MY ice at the beginning of each year is 3774 x 10(exp 3) sq km (2000), 3896 x 10(exp 3) sq km (2001), 4475 x 10(exp 3) sq km (2002), and 4122 x 10(exp 3) sq km (2003). Uncertainties in coverage are approx.150 x 10(exp 3) sq km. In the mean, on 1 January, MY ice covers approx.60% of the Arctic Ocean. Ice export reduces this coverage to approx.55% by 1 May. From the multiple annual cycles, the area of first-year (FY) ice that survives the intervening summers are 1192 x 10(exp 3) sq km (2000), 1509 x 10(exp 3) sq km (2001), and 582 x 10(exp 3) sq km (2002). In order for the MY coverage to remain constant from year to year, these replenishment areas must balance the overall area export and melt during the summer. The effect of the record minimum in Arctic sea ice area during the summer of 2002 is seen in the lowest area of surviving FY ice of the three summers. In addition to the spatial coverage, the location of the PIZ is important. One consequence of the unusual location of the PIZ at the end of the summer of 2002 is the preconditioning for enhanced export of MY ice into the Barents and Kara seas. Differences between the minimums in summer sea ice coverage from our estimates and passive microwave observations are discussed.

Bringing an Effective Solar Sail Design Toward TRL 6

NASA Technical Reports Server (NTRS)

Lichodziejewski, David; West, John; Reinert, Rich; Belvin, Keith; Pappa, Richard; Derbes, Billy

2003-01-01

Solar sails reflect photons streaming from the sun and convert some of the energy into thrust. This thrust, though small, is continuous and acts for the life of the mission without the need for propellant ( I ) . Recent advances in sail materials and ultra-low mass structures have enabled a host of useful missions utilizing solar sail propulsion. The team of L Garde, Jet Propulsion Laboratories, Ball Aerospace, and Langley Research Center, under the direction of NASA, has been developing a solar sail configuration to address NASA s future space propulsion needs. Utilizing inflatably deployed and Sub Tg rigidized boom components, this 10,000 sq m sailcraft achieves an areal density of 14.1 g/sq m and a characteristic acceleration of 0.58 mm/s . The entire configuration released by the upper stage has a mass of 232.9 kg and requires just 1.7 d of volume in the booster. After deployment, 92.2 kg of non-flight required equipment is jettisoned resulting in a sailcraft mass, including payload and control system, of 140.7 kg. This document outlines the accomplishments of a Phase 1 effort to advance the technology readiness level (TRL) of the concept from 3 toward a TRL of 6. The Phase 1 effort, the first of three proposed phases, addressed the design of the solar sail, its application to several missions currently under review at NASA, and developed a ground tes plan to bring the technology toward a TRL of 6.

A Tale of Two Inlets: Tidal Currents at Two Adjacent Inlets in the Indian River Lagoon

NASA Astrophysics Data System (ADS)

Webb, B. M.; Weaver, R. J.

2012-12-01

The tidal currents and hydrography at two adjacent inlets of the Indian River Lagoon estuary (Florida) were recently measured using a personal watercraft-based coastal profiling system. Although the two inlets—Sebastian Inlet and Port Canaveral Inlet—are separated by only 60 km, their characteristics and dynamics are quite unique. While Sebastian Inlet is a shallow (~4 m), curved inlet with a free connection to the estuary, Port Canaveral Inlet is dominated by a deep (~13 m), straight ship channel and has limited connectivity to the Banana River through a sector gate lock. Underway measurements of tidal currents were obtained using a bottom tracking acoustic Doppler current profiler; vertical casts of hydrography were obtained with a conductivity-temperature-depth profiling instrument; and continuous underway measurements of surface water hydrography were made using a Portable SeaKeeper system. Survey transects were performed to elucidate the along-channel variability of tidal flows, which appears to be significant in the presence of channel curvature. Ebb and flood tidal currents in Sebastian Inlet routinely exceeded 2.5 m/s from the surface to the bed, and an appreciable phase lag exists between tidal stage and current magnitude. The tidal currents at Port Canaveral Inlet were much smaller (~0.2 m/s) and appeared to be sensitive to meteorological forcing during the study period. Although the lagoon has free connections to the ocean 145 km to the north and 45 km to the south, Sebastian Inlet likely drains much of the lagoon to its north, an area of ~550 sq. km.

A sampling system for estimating the cultivation of wheat (Triticum aestivum L) from LANDSAT data. M.S. Thesis - 21 Jul. 1983

NASA Technical Reports Server (NTRS)

Parada, N. D. J. (Principal Investigator); Moreira, M. A.

1983-01-01

Using digitally processed MSS/LANDSAT data as auxiliary variable, a methodology to estimate wheat (Triticum aestivum L) area by means of sampling techniques was developed. To perform this research, aerial photographs covering 720 sq km in Cruz Alta test site at the NW of Rio Grande do Sul State, were visually analyzed. LANDSAT digital data were analyzed using non-supervised and supervised classification algorithms; as post-processing the classification was submitted to spatial filtering. To estimate wheat area, the regression estimation method was applied and different sample sizes and various sampling units (10, 20, 30, 40 and 60 sq km) were tested. Based on the four decision criteria established for this research, it was concluded that: (1) as the size of sampling units decreased the percentage of sampled area required to obtain similar estimation performance also decreased; (2) the lowest percentage of the area sampled for wheat estimation with relatively high precision and accuracy through regression estimation was 90% using 10 sq km s the sampling unit; and (3) wheat area estimation by direct expansion (using only aerial photographs) was less precise and accurate when compared to those obtained by means of regression estimation.

Solar radiation, phytoplankton pigments and the radiant heating of the equatorial Pacific warm pool

NASA Technical Reports Server (NTRS)

Siegel, David A.; Ohlmann, J. Carter; Washburn, Libe; Bidigare, Robert R.; Nosse, Craig T.; Fields, Erik; Zhou, Yimei

1995-01-01

Recent optical, physical, and biological oceanographic observations are used to assess the magnitude and variability of the penetrating flux of solar radiation through the mixed layer of the warm water pool (WWP) of the western equatorial Pacific Ocean. Typical values for the penetrative solar flux at the climatological mean mixed layer depth for the WWP (30 m) are approx. 23 W/sq m and are a large fraction of the climatological mean net air-sea heat flux (approx. 40 W/sq m). The penetrating solar flux can vary significantly on synoptic timescales. Following a sustained westerly wind burst in situ solar fluxes were reduced in response to a near tripling of mixed layer phytoplankton pigment concentrations. This results in a reduction in the penetrative flux at depth (5.6 W/sq m at 30 m) and corresponds to a biogeochemically mediated increase in the mixed layer radiant heating rate of 0.13 C per month. These observations demonstrate a significant role of biogeochemical processes on WWP thermal climate. We speculate that this biogeochemically mediated feedback process may play an important role in enhancing the rate at which the WWP climate system returns to normal conditions following a westerly wind burst event.

Bounding the Role of Black Carbon in the Climate System: a Scientific Assessment

NASA Technical Reports Server (NTRS)

Bond, T. C.; Doherty, S. J.; Fahey, D. W.; Forster, P. M.; Bernsten, T.; DeAngelo, B. J.; Flanner, M. G.; Ghan, S.; Karcher, B.; Koch, D.;

Mn-53 in the Apollo 15 and 16 drill stems - Evidence for surface mixing

NASA Technical Reports Server (NTRS)

Nishiizumi, K.; Imamura, M.; Honda, M.; Russ, G. P., III; Kohl, C. P.; Arnold, J. R.

1976-01-01

The activity of cosmic ray produced Mn-53 has been measured in a series of samples from the upper 10 cm of the Apollo 15 and 16 drill stems. The activity profiles for both cores indicate disturbance to depths of about 3 g/sq cm within the last 6 m.y. In at least one case (Apollo 16) the soil has been gardened to at least 14 g/sq cm within the last 10 m.y., and material from the upper less than 2 g/sq cm has been buried to 14 g/sq cm by this gardening. The results for the Apollo 15 core are compatible with a wide variety of possible histories including loss or gain of material.

The harmonic development of the Earth tide generating potential due to the direct effect of the planets

NASA Astrophysics Data System (ADS)

Hartmann, Torsten; Wenzel, Hans-Georg

1994-09-01

The time-harmonic development of the Earth tide generating potential due to the direct effect of the planets Venus, Jupiter, Mars, Mercury and Saturn has been computed. The catalog of the fully normalized potential coefficients contains 1483 waves. It is based on the DE102 numerical ephemeris of the planets between years 1900 and 2200. Gravity tides due to the planets computed from the catalog at the surface of the Earth have an accuracy of about 0.027 pm/sq s (1 pm/sq s = 10(exp -12) m/sq s = 0.1 ngal) rms and 0.160 / 0.008 pm/sq s at maximum in time / frequency domain using the new benchmark tidal gravity series (Wenzel 1994).

High Mobility SiGe/Si n-Type Structures and Field Effect Transistors on Sapphire Substrates

NASA Technical Reports Server (NTRS)

Alterovitz, Samuel A.; Ponchak, George E.; Mueller, Carl H.; Croke, Edward T.

2004-01-01

SiGe/Si n-type modulation doped field effect transistors (MODFETs) fabricated on sapphire substrates have been characterized at microwave frequencies for the first time. The highest measured room temperature electron mobility is 1380 sq cm/V-sec at a carrier density of 1.8 x 10(exp 12)/sq cm for a MODFET structure, and 900 sq cm/V-sec at a carrier density of 1.3 x 10/sq cm for a phosphorus ion implanted sample. A two finger, 2 x 200 micron gate n-MODFET has a peak transconductance of 37 mS/mm at a drain to source voltage of 2.5 V and a transducer gain of 6.4 dB at 1 GHz.

Solar power satellite system sizing tradeoffs

NASA Technical Reports Server (NTRS)

Arndt, G. D.; Monford, L. G.

1981-01-01

Technical and economic tradeoffs of smaller solar power satellite systems configured with larger antennas, reduced output power, and smaller rectennas, are considered. The differential costs in electricity for seven antenna/rectenna configurations operating at 2.45 GHz and five satellite systems operating at 5.8 GHz are calculated. Two 2.45 GHz configurations dependent upon the ionospheric power density limit are chosen as examples. If the ionospheric limit could be increased to 54 mW sq/cm from the present 23 mW sq/cm level, a 1.53 km antenna satellite operating at 2.45 GHz would provide 5.05 GW of output power from a 6.8 km diameter rectenna. This system gives a 54 percent reduction in rectenna area relative to the reference solar power satellite system at a modest 17 percent increase in electricity costs. At 5.8 GHz, an 0.75 km antenna providing 2.72 GW of power from a 5.8 km diameter rectenna is selected for analysis. This configuration would have a 67 percent reduction in rectenna area at a 36 percent increase in electricity costs. Ionospheric, atmospheric, and thermal limitations are discussed. Antenna patterns for three configurations to show the relative main beam and sidelobe characteristics are included.

X-Ray Imaging Study

NASA Technical Reports Server (NTRS)

OBrien, Susan K.; Workman, Gary L.

1996-01-01

The space environment in which the Space Station Freedom and other space platforms will orbit is truly a hostile environment. For example, the currently estimated integral fluence for electrons above 1 Mev at 2000 nautical miles is above 2 x 1O(exp 10) electrons/sq cm/day and the proton integral fluence is above 1 x 10(exp 9) protons/sq cm/day. At the 200 - 400 nautical miles, which is more representative of the altitude which will provide the environment for the Space Station, each of these fluences will be proportionally less; however, the data indicates that the radiation environment will obviously have an effect on structural materials exposed to the environment for long durations. The effects of this combined environment is the issue which needs to be understood for the long term exposure of structures in space. At the same time, there will be substantial potential for collisions between the space platforms and space debris. The current NASA catalogue contains over 4500 objects floating in space which are not considered payloads. This debris can have significant effects on collision with orbiting spacecraft. In order to better understand the effect of these hostile phenomena on spacecraft, several types of studies are being performed to simulate at some level the effect of the environment. In particular the study of debris clouds produced by hypervelocity impact on the various surfaces anticipated on the Space Station is very important at this point in time. The need to assess the threat of such debris clouds on space structures is an on-going activity. The Space Debris Impact facility in Building 4612 provides a test facility to monitor the types of damage produced with hypervelocity impact. These facilities are used to simulate space environmental effects from energetic particles. Flash radiography or x-ray imaging has traditionally provided such information and as such has been an important tool for recording damage in situ with the event. The proper operation of the system can provide much useful information with respect to parametric analysis of the hypervelocity experiment. The following report outlines the procedures developed to optimize the operation of the x-ray imaging system and its operational characteristics.

Test bed ion engine development

NASA Technical Reports Server (NTRS)

Aston, G.; Deininger, W. D.

1984-01-01

A test bed ion (TBI) engine was developed to serve as a tool in exploring the limits of electrostatic ion thruster performance. A description of three key ion engine components, the decoupled extraction and amplified current (DE-AC) accelerator system, field enhanced refractory metal (FERM) hollow cathode and divergent line cusp (DLC) discharge chamber, whose designs and operating philosophies differ markedly from conventional thruster technology is given. Significant program achievements were: (1) high current density DE-AC accelerator system operation at low electric field stress with indicated feasibility of a 60 mA/sq cm argon ion beam; (2) reliable FERM cathode start up times of 1 to 2 secs. and demonstrated 35 ampere emission levels; (3) DLC discharge chamber plasma potentials negative of anode potential; and (4) identification of an efficient high plasma density engine operating mode. Using the performance projections of this program and reasonable estimates of other parameter values, a 1.0 Newton thrust ion engine is identified as a realizable technology goal. Calculations show that such an engine, comparable in beam area to a J series 30 cm thruster, could, operating on Xe or Hg, have thruster efficiencies as high as 0.76 and 0.78 respectively, with a 100 eV/ion discharge loss.

The role of silver in the processing and properties of Bi-2212

NASA Technical Reports Server (NTRS)

Lang, TH.; Heeb, B.; Buhl, D.; Gauckler, L. J.

1995-01-01

The influence of the silver content and the oxygen partial pressure on the solidus temperature and the weight loss during melting of Bi2Sr2Ca1Cu2O(x) has been examined by means of DTA and TGA. By decreasing the oxygen partial pressure the solidus is lowered (e.g. del T = 59 C by decreasing pO2 from 1 atm to 0.001 atm) and the weight loss is increased. The addition of silver causes two effects: (1) the solidus is further decreased (e.g. 2 wt% Ag lower T (solidus) by up to 25 C, depending on the oxygen partial pressure); and (2) the weight loss during melting is reduced. Thick films (10-20 micron in thickness) with 0 and 5 wt% silver and bulk samples with) and 2.7 wt% silver were melt processed in flowing oxygen on a silver substrate in the DTA, allowing the observation of the melting process and a good temperature control. The critical current densities are vigorously dependent on the maximum processing temperature. The highest j(sub c) in thick films (8000 A/sq cm at 77 K, O T) was reached by melting 7 C above the solidus temperature. The silver addition shows no significant effect on the processing parameters or the superconducting properties. The highest j(sub c) for bulk samples (1 mm in thickness) was obtained by partial melting at 900 C or 880 C, depending on the silver content of the powder (0 or 2.7 wt%). The j(sub c) of the samples is slightly enhanced from 1800 A/sq cm (at 77 K, O T) to 2000 A/sq cm by the silver addition. To be able to reach at least 80% of the maximum critical current density, the temperature has to be controlled in a window of 5 C for thick films and 17 C for bulk samples.

Homogeneous alignment of nematic liquid crystals by ion beam etched surfaces

NASA Technical Reports Server (NTRS)

Wintucky, E. G.; Mahmood, R.; Johnson, D. L.

1979-01-01

A wide range of ion beam etch parameters capable of producing uniform homogeneous alignment of nematic liquid crystals on SiO2 films are discussed. The alignment surfaces were generated by obliquely incident (angles of 5 to 25 deg) argon ions with energies in the range of 0.5 to 2.0 KeV, ion current densities of 0.1 to 0.6 mA sq cm and etch times of 1 to 9 min. A smaller range of ion beam parameters (2.0 KeV, 0.2 mA sq cm, 5 to 10 deg and 1 to 5 min.) were also investigated with ZrO2 films and found suitable for homogeneous alignment. Extinction ratios were very high (1000), twist angles were small ( or = 3 deg) and tilt-bias angles very small ( or = 1 deg). Preliminary scanning electron microscopy results indicate a parallel oriented surface structure on the ion beam etched surfaces which may determine alignment.

Development of pulsed processes for the manufacture of solar cells

NASA Technical Reports Server (NTRS)

Minnucci, J. A.

1979-01-01

Low-energy ion implantation processes for the automated production of silicon solar cells were investigated. Phosphorus ions at an energy of 10 keV and dose of 2 x 10 to the 15th power/sq cm were implanted in silicon solar cells to produce junctions, while boron ions at 25 keV and 5 x 10 to the 15th power were implanted in the cells to produce effective back surface fields. An ion implantation facility with a beam current up to 4 mA and a production throughput of 300 wafers per hour was designed and installed. A design was prepared for a 100 mA, automated implanter with a production capacity of 100 MW sub e/sq cm per year. Two process sequences were developed which employ ion implantation and furnace or pulse annealing. A computer program was used to determine costs for junction formation by ion implantation and various furnace annealing cycles to demonstrate cost effectiveness of these methods.

Detection of Flooding Responses at the River Basin Scale Enhanced by Land use Change

NASA Technical Reports Server (NTRS)

McCormick, Brian C.; Eshleman, Keith N.; Griffith, Jeff L.; Townsend, Philip A.

2009-01-01

The Georges Creek watershed (area 187.5 sq km) in western Maryland (United States) has experienced land use changes (>17% of area) associated with surface mining of coal. The adjacent Savage River watershed (area 127.2 sq km) is unmined. Moments of flood frequency distributions indicated that climatic variability affected both watersheds similarly. Normalizing annual maximum flows by antecedent streamflow and causative precipitation helped identify trends in flooding response. Analysis of contemporary storm events using Next Generation Weather Radar (NEXRAD) stage III precipitation data showed that Georges Creek floods are characterized by higher peak runoff and a shorter centroid lag than Savage River floods, likely attributable to differences in current land use. Interestingly, Georges Creek produces only two thirds of the storm-flow volume as Savage River, apparently because of infiltration into abandoned deep mine workings and an associated transbasin diversion constructed circa 1900. Empirical trend analysis is thus complicated by both hydroclimatic variability and the legacy of deep mining in the basin.

Diffusion lengths in irradiated N/P InP-on-Si solar cells

NASA Technical Reports Server (NTRS)

Wojtczuk, Steven; Colerico, Claudia; Summers, Geoffrey P.; Walters, Robert J.; Burke, Edward A.

1995-01-01

Indium phosphide (InP) solar cells are being made on silicon (Si) wafers (InP/Si) to take advantage of both the radiation-hardness properties of the InP solar cell and the light weight and low cost of Si wafers compared to InP or germanium (Ge) wafers. The InP/Si cell application is for long duration and/or high radiation orbit space missions. InP/Si cells have higher absolute efficiency after a high radiation dose than gallium arsenide (GaAs) or silicon (Si) solar cells. In this work, base electron diffusion lengths in the N/P cell are extracted from measured AM0 short-circuit photocurrent at various irradiation levels out to an equivalent 1 MeV fluence of 1017 1 MeV electrons/sq cm for a 1 sq cm 12% BOL InP/Si cell. These values are then checked for consistency by comparing measured Voc data with a theoretical Voc model that includes a dark current term that depends on the extracted diffusion lengths.

Greenland ice sheet outlet glacier front changes: comparison of year 2008 with past years

NASA Astrophysics Data System (ADS)

Decker, D. E.; Box, J.; Benson, R.

2008-12-01

NASA's Moderate Resolution Imaging Spectroradiometer (MODIS) imagery are used to calculate inter-annual, end of summer, glacier front area changes at 10 major Greenland ice sheet outlets over the 2000-2008 period. To put the recent 8 end of summer net annual changes into a longer perspective, glacier front position information from the past century are also incorporated. The largest MODIS-era area changes are losses/retreats; found at the relatively large Petermann Gletscher, Zachariae Isstrom, and Jakobshavn Isbrae. The 2007-2008 net ice area losses were 63.4 sq. km, 21.5 sq. km, and 10.9 sq. km, respectively. Of the 10 largest Greenland glaciers surveyed, the total net cumulative area change from end of summer 2000 to 2008 is -536.6 sq km, that is, an area loss equivalent with 6.1 times the area of Manhattan Is. (87.5 sq km) in New York, USA. Ice front advances are evident in 2008; also at relatively large and productive (in terms of ice discharge) glaciers of Helheim (5.7 sq km), Store Gletscher (4.9 sq km), and Kangerdlugssuaq (3.4 sq km). The largest retreat in the 2000-2008 period was 54.2 sq km at Jakobshavn Isbrae between 2002 and 2003; associated with a floating tongue disintegration following a retreat that began in 2001 and has been associated with thinning until floatation is reached; followed by irreversible collapse. The Zachariae Isstrom pro-glacial floating ice shelf loss in 2008 appears to be part of an average ~20 sq km per year disintegration trend; with the exception of the year 2006 (6.2 sq km) advance. If the Zachariae Isstrom retreat continues, we are concerned the largest ice sheet ice stream that empties into Zachariae Isstrom will accelerate, the ice stream front freed of damming back stress, increasing the ice sheet mass budget deficit in ways that are poorly understood and could be surprisingly large. By approximating the width of the surveyed glacier frontal zones, we determine and present effective glacier normalized length (L') changes that also will be presented at the meeting. The narrow Ingia Isbrae advanced in L' the most in 2006-2007 by 9.2 km. Jakobshavn decreased in L' the most in 2002-2003 by 8.0 km. Petermann decreased in length the most in 2000-2001, that is, L' = -5.3 km and again by L' = -3.9 km in 2007-2008. Helheim Gl. retreated in 2004-2005 by L' = -4.6 km and advanced 2005-2006 by L' = 4.4 km. The 10 glacier average L' change from end of summer 2000 end of summer 2008 was 0.6 km. Results from a growing list of glaciers will be presented. We attempt to interpret the observed glacier changes using glaciological theory and regional climate observations.

Vacuum microelectronics for beam power and rectennas

NASA Technical Reports Server (NTRS)

Gray, Henry F.

1989-01-01

Vacuum Microelectronic devices can be described as vacuum transistors or micro-miniature vacuum tubes, as one chooses. The fundamental reason behind this new technology is the very large current densities available from field emitters, namely as high as 10(8) A/sq cm. Array current densities as high as 1000 A/sq cm have been measured. Total electron transit times from source to drain for 1 micron feature size devices have been predicted to be about 150fs. This very short transit time implies the possibility of submillimeter wave transmitters and rectennas in devices which can operate with reasonably high voltages and which are small in size and are lightweight. In addition, they are expected to be extremely radiation hard and very temperature insensitive. That is, they are expected to have radiation hardness characteristics similar to vacuum tubes, and both the high temperature and low temperature limits should be determined by the package. That is, there should be no practical intrinsic temperature or carrier freezeout problems for devices based on metals or composites. But the technology is difficult to implement at the present time because it is based on 300 to 500 angstrom radius field emitters which must be relatively uniform. There is also the need to understand the non-equilibrium transport physics in the near-surface regions of the field emitters.

Cosmic Dawn Intensity Mapper

NASA Astrophysics Data System (ADS)

Cooray, Asantha

2018-01-01

Cosmic Dawn Intensity Mapper (CDIM) is a 1.0m-class infrared telescope capable of three-dimensional spectro-imaging observations over the wavelength range of 0.75 to 7.5 microns, at a spectral resolving power at or better than 300. This will be achieved with linear variablefilters (LVFs) and a large field-of-view (FoV). The survey strategy using spacecraft operations following a shift and stare mode will result in more than 1300 independent narrow-band spectral images of the sky at a given location. Currently prioritized science programs, taking over three-years of a five-year mission, will be accomplished with a two-tiered wedding-cake survey with the shallowest spanning close to 300 sq. degrees and the deepest tier of about 25 sq. degrees.The remaining two-years could be used for additional survey programs (the wide tier can be expanded to 1000 sq. degrees) or for use by the astronomical community through a General Observing (GO) campaign. CDIM survey data will allow us to (i) establish the initial mass function of stars in galaxies present during reionization, (ii) definitively address AGN/quasar contribution to the reionization photon budget; (iii) establish the environmental dependence of star-formation during reionization through clustering and other environmental measurements; (iv) establish the metal abundance of first-light galaxies during reionization over two decades of stellar mass; (v) measure 3D intensity fluctuations during reionization in both Ly-alpha and H-alpha; and (vi) combine intensity fluctuations with 21-cm data to establish the topology of reionization bubbles.

Nucleon Spin Structure and Constituent Quark Model

NASA Astrophysics Data System (ADS)

Wang, Fan; Qing, Di; Chen, Xiang-Song; Goldman, T.

1998-10-01

The success of the constituent quark model has been challenged by the nucleon spin structure discovered in polarized deep inelastic scattering (DIS). We find that this puzzle is due to misidentifying the axial charge Δ q and the nonrelativistic quark spin. The space component of the quark axial vector current operator, int d^3x\\overlineψ γγ_5ψ =2s_q, defines the quark spin operator s_q, including not only the Pauli spin operator, which corresponds to the nonrelativistic quark spin s_q^NR, but also relativistic and quark-antiquark pair creation (annihilation) correction terms. Both of these suppress the quark spin contribution for a nucleon at rest due to transverse motion of the quark. The relativistic quark orbital angular momentum operator L_q=int d^3x\\overlineψ x× fracpartial iψ includes L^NRq and two correction terms which are exactly the same as those of sq but of opposite sign. They provide compensation which keeps the total nucleon spin frac 12 untouched no matter what kind of quark model is used. Nucleon spin can be decomposed either as s_q+Lq or as s_q^NR+L_q^NR. (The gluon degree of freedom is assumed to be frozen in the nucleon ground state at low energy scales.) The tensor charge δ q=int d^3x\\overlineψ Σ ψ of the nucleon is predicted to have similar but smaller corrections.

Identifying Microlensing Events in Large, Non-Uniformly Sampled Surveys: The Case of the Palomar Transient Factory

NASA Astrophysics Data System (ADS)

Price-Whelan, Adrian M.; Agueros, M. A.; Fournier, A.; Street, R.; Ofek, E.; Levitan, D. B.; PTF Collaboration

2013-01-01

Many current photometric, time-domain surveys are driven by specific goals such as searches for supernovae or transiting exoplanets, or studies of stellar variability. These goals in turn set the cadence with which individual fields are re-imaged. In the case of the Palomar Transient Factory (PTF), several such sub-surveys are being conducted in parallel, leading to extremely non-uniform sampling over the survey's nearly 20,000 sq. deg. footprint. While the typical 7.26 sq. deg. PTF field has been imaged 20 times in R-band, ~2300 sq. deg. have been observed more than 100 times. We use the existing PTF data 6.4x107 light curves) to study the trade-off that occurs when searching for microlensing events when one has access to a large survey footprint with irregular sampling. To examine the probability that microlensing events can be recovered in these data, we also test previous statistics used on uniformly sampled data to identify variables and transients. We find that one such statistic, the von Neumann ratio, performs best for identifying simulated microlensing events. We develop a selection method using this statistic and apply it to data from all PTF fields with >100 observations to uncover a number of interesting candidate events. This work can help constrain all-sky event rate predictions and tests microlensing signal recovery in large datasets, both of which will be useful to future wide-field, time-domain surveys such as the LSST.

Iridium-Doped Ruthenium Oxide Catalyst for Oxygen Evolution

NASA Technical Reports Server (NTRS)

Valdez, Thomas I.; Narayan, Sri R.; Billings, Keith J.

2011-01-01

NASA requires a durable and efficient catalyst for the electrolysis of water in a polymer-electrolyte-membrane (PEM) cell. Ruthenium oxide in a slightly reduced form is known to be a very efficient catalyst for the anodic oxidation of water to oxygen, but it degrades rapidly, reducing efficiency. To combat this tendency of ruthenium oxide to change oxidation states, it is combined with iridium, which has a tendency to stabilize ruthenium oxide at oxygen evolution potentials. The novel oxygen evolution catalyst was fabricated under flowing argon in order to allow the iridium to preferentially react with oxygen from the ruthenium oxide, and not oxygen from the environment. Nanoparticulate iridium black and anhydrous ruthenium oxide are weighed out and mixed to 5 18 atomic percent. They are then heat treated at 300 C under flowing argon (in order to create an inert environment) for a minimum of 14 hours. This temperature was chosen because it is approximately the creep temperature of ruthenium oxide, and is below the sintering temperature of both materials. In general, the temperature should always be below the sintering temperature of both materials. The iridium- doped ruthenium oxide catalyst is then fabricated into a PEM-based membrane- electrode assembly (MEA), and then mounted into test cells. The result is an electrolyzer system that can sustain electrolysis at twice the current density, and at the same efficiency as commercial catalysts in the range of 100-200 mA/sq cm. At 200 mA/sq cm, this new system operates at an efficiency of 85 percent, which is 2 percent greater than commercially available catalysts. Testing has shown that this material is as stable as commercially available oxygen evolution catalysts. This means that this new catalyst can be used to regenerate fuel cell systems in space, and as a hydrogen generator on Earth.

Patterns and determinants of small-quantity LNS utilization in rural Malawi and Mozambique: considerations for interventions with specialized nutritious foods.

PubMed

Kodish, Stephen R; Aburto, Nancy J; Nseluke Hambayi, Mutinta; Dibari, Filippo; Gittelsohn, Joel

2017-01-01

Small-quantity, lipid-based nutrient supplements (SQ-LNS) show promise to improve the quality of maternal and child diets, particularly during the first 1000 days of life. The potential of SQ-LNS to impact positively upon nutritional status relies on numerous factors, including complementary dietary intake, disease prevalence and dynamics of household utilization, including sharing practices. Therefore, this study sought to elucidate the patterns and determinants of SQ-LNS utilization among children 6-23 months and potential sharing practices of other household members prior to intervention development. In Ntchisi, Malawi and Cabo Delgado, Mozambique, both rural, agricultural settings, we conducted two home-feeding trials of 8 and 6 weeks, respectively, nested within a larger multi-phase, emergent formative research design. Multiple methods, including in-depth interviews (n = 38), direct meal observations (n = 80), full-day child observations (n = 38) and spot checks of SQ-LNS supply (n = 23), were conducted with households (n = 35 in Malawi; n = 24 in Mozambique). Overall, the SQ-LNS was utilized contrary to its recommended use, with 50% of households in Malawi reporting running out of stock too early and 87% of households in Mozambique either overusing or underusing the product. Utilization of SQ-LNS was manifested in four patterns of overuse and two of underuse and was determined by factors at multiple levels of influence. Maternal and child health efforts need to consider the reasons behind choices by households to overuse or underuse SQ-LNS and design intervention strategies to increase the likelihood of its appropriate utilization. © 2016 John Wiley & Sons Ltd.

Ultrafast dynamics in co-sensitized photocatalysts under visible and NIR light irradiation.

PubMed

Patwari, Jayita; Chatterjee, Arka; Sardar, Samim; Lemmens, Peter; Pal, Samir Kumar

2018-04-18

Co-sensitization to achieve a broad absorption window is a widely accepted technique in light harvesting nanohybrid synthesis. Protoporphyrin (PPIX) and squaraine (SQ2) are two organic sensitizers absorbing in the visible and NIR wavelength regions of the solar spectrum, respectively. In the present study, we have sensitized zinc oxide (ZnO) nanoparticles using PPIX and SQ2 simultaneously for their potential use in broad-band solar light harvesting in photocatalysis. Förster resonance energy transfer (FRET) from PPIX to SQ2 in close proximity to the ZnO surface has been found to enhance visible light photocatalysis. In order to confirm the effect of intermolecular FRET in photocatalysis, the excited state lifetime of the energy donor dye PPIX has been modulated by inserting d10 (ZnII) and d7 (CoII) metal ions in the central position of the dye (PP(Zn) and PP(Co)). In the case of PP(Co)-SQ2, extensive photo-induced ligand to metal charge transfer counteracts the FRET efficiency while efficient FRET has been observed for the PP(Zn)-SQ2 pair. This observation has been justified by the comparison of the visible light photocatalysis of the respective nanohybrids with several control studies. We have also investigated the NIR photocatalysis of the co-sensitized nanohybrids which reveals that reduced aggregation of SQ2 due to co-sensitization of PPIX increases the NIR photocatalysis. However, core-metalation of PPIX reduces the NIR photocatalytic efficacy, most probably due to excited state charge transfer from SQ2 to the metal centre of PP(Co)/PP(Zn) through the conduction band of the host ZnO nanoparticles.

Clinical features of squamous cell lung cancer with anaplastic lymphoma kinase (ALK)-rearrangement: a retrospective analysis and review

PubMed Central

Watanabe, Junko; Togo, Shinsaku; Sumiyoshi, Issei; Namba, Yukiko; Suina, Kentaro; Mizuno, Takafumi; Kadoya, Kotaro; Motomura, Hiroaki; Iwai, Moe; Nagaoka, Tetsutaro; Sasaki, Shinichi; Hayashi, Takuo; Uekusa, Toshimasa; Abe, Kanae; Urata, Yasuo; Sakurai, Fuminori; Mizuguchi, Hiroyuki; Kato, Shunsuke; Takahashi, Kazuhisa

2018-01-01

Anti-anaplastic lymphoma kinase (ALK)-targeted therapy dramatically improves therapeutic responses in patients with ALK-rearranged lung adenocarcinoma (Ad-LC). A few cases of squamous cell lung carcinoma (Sq-LC) with ALK rearrangement have been reported; however, the clinicopathological features and clinical outcomes following treatment with ALK inhibitors are unknown. We addressed this in the present study by retrospectively comparing the clinical characteristics of five patients with ALK-rearranged Sq-LC with those of patients with ALK-rearranged Ad-LC and by evaluating representative cases of ALK inhibitor responders and non-responders. The prevalence of ALK rearrangement in Sq-LCs was 1.36%. Progression-free survival (PFS) after initial treatment with crizotinib was significantly shorter in Sq-LC than in Ad-LC with ALK rearrangement (p = 0.033). Two ALK rearrangements assayed by fluorescence in situ hybridization (FISH)-positive/immunohistochemistry-negative cases did not respond to crizotinb, and PFS decreased following alectinib treatment of ALK-rearranged Sq-LC (p = 0.045). A rebiopsy revealed that responders to ceritinib harbored the L1196M mutation, which causes resistance to other ALK inhibitors. However, non-responders were resistant to all ALK inhibitors, despite the presence of ALK rearrangement in FISH-positive circulating tumor cells and circulating free DNA and absence of the ALK inhibitor resistance mutation. These results indicate that ALK inhibitors remain a reasonable therapeutic option for ALK-rearranged Sq-LC patients who have worse outcomes than ALK-rearranged Ad-LC patients and that resistance mechanisms are heterogeneous. Additionally, oncologists should be aware of the possibility of ALK-rearranged Sq-LC based on clinicopathological features, and plan second-line therapeutic strategies based on rebiopsy results in order to improve patient outcome. PMID:29844868

Flurbiprofen axetil increases arterial oxygen partial pressure by decreasing intrapulmonary shunt in patients undergoing one-lung ventilation.

PubMed

Chai, Xiao-Qing; Ma, Jun; Xie, Yan-Hu; Wang, Di; Chen, Kun-Zhou

2015-12-01

In the present study, we investigated whether flurbiprofen axetil (FA) alleviates hypoxemia during one-lung ventilation (OLV) by reducing the pulmonary shunt/total perfusion (Q s/Q t) ratio, and examined the relationship between the Q s/Q t ratio and the thromboxane B2 (TXB2)/6-keto-prostaglandin F1α (6-K-PGF1α) ratio. Sixty patients undergoing esophageal resection for carcinoma were randomly assigned to groups F and C (n = 30 for each group). FA and placebo were administered i.v. 15 min before skin incision in groups F and C, respectively. The partial pressure of arterial oxygen (PaO2) was measured and the Q s/Q t ratio was calculated. Serum TXB2, 6-K-PGF1α, and endothelin (ET) were measured by radioimmunoassay. The relationship between TXB2/6-K-PGF1α and Q s/Q t was investigated. Compared with group C, PaO2 was higher and the Q s/Q t ratio was lower during OLV in group F (P < 0.05). After treatment with FA, both serum TXB2 and 6-K-PGF1α decreased significantly (P < 0.05) but the TXB2/6-K-PGF1α ratio increased significantly (P < 0.01). Increases in the TXB2/6-K-PGF1α ratio were correlated with reductions in the Q s/Q t ratio during OLV in group F (r = -0.766, P < 0.01). There was no significant difference in serum ET between groups F and C. Treatment with FA reduced the Q s/Q t ratio and further increased the PaO2 level during OLV, possibly due to upregulation of the vasoactive agent TXB2/6-K-PGF1α ratio.

Clinical features of squamous cell lung cancer with anaplastic lymphoma kinase (ALK)-rearrangement: a retrospective analysis and review.

PubMed

Watanabe, Junko; Togo, Shinsaku; Sumiyoshi, Issei; Namba, Yukiko; Suina, Kentaro; Mizuno, Takafumi; Kadoya, Kotaro; Motomura, Hiroaki; Iwai, Moe; Nagaoka, Tetsutaro; Sasaki, Shinichi; Hayashi, Takuo; Uekusa, Toshimasa; Abe, Kanae; Urata, Yasuo; Sakurai, Fuminori; Mizuguchi, Hiroyuki; Kato, Shunsuke; Takahashi, Kazuhisa

2018-05-08

Anti-anaplastic lymphoma kinase (ALK)-targeted therapy dramatically improves therapeutic responses in patients with ALK-rearranged lung adenocarcinoma (Ad-LC). A few cases of squamous cell lung carcinoma (Sq-LC) with ALK rearrangement have been reported; however, the clinicopathological features and clinical outcomes following treatment with ALK inhibitors are unknown. We addressed this in the present study by retrospectively comparing the clinical characteristics of five patients with ALK-rearranged Sq-LC with those of patients with ALK-rearranged Ad-LC and by evaluating representative cases of ALK inhibitor responders and non-responders. The prevalence of ALK rearrangement in Sq-LCs was 1.36%. Progression-free survival (PFS) after initial treatment with crizotinib was significantly shorter in Sq-LC than in Ad-LC with ALK rearrangement ( p = 0.033). Two ALK rearrangements assayed by fluorescence in situ hybridization (FISH)-positive/immunohistochemistry-negative cases did not respond to crizotinb, and PFS decreased following alectinib treatment of ALK-rearranged Sq-LC ( p = 0.045). A rebiopsy revealed that responders to ceritinib harbored the L1196M mutation, which causes resistance to other ALK inhibitors. However, non-responders were resistant to all ALK inhibitors, despite the presence of ALK rearrangement in FISH-positive circulating tumor cells and circulating free DNA and absence of the ALK inhibitor resistance mutation. These results indicate that ALK inhibitors remain a reasonable therapeutic option for ALK-rearranged Sq-LC patients who have worse outcomes than ALK-rearranged Ad-LC patients and that resistance mechanisms are heterogeneous. Additionally, oncologists should be aware of the possibility of ALK-rearranged Sq-LC based on clinicopathological features, and plan second-line therapeutic strategies based on rebiopsy results in order to improve patient outcome.

Scientific grade CCDs from EG & G Reticon

NASA Technical Reports Server (NTRS)

Cizdziel, Philip J.

1990-01-01

The design and performance of three scientific grade CCDs are summarized: a 1200 x 400 astronomical array of 27 x 27 sq micron pixels, a 512 x 512 scientific array of 27 x 27 sq micron pixels and a 404 x 64 VNIR array of 52 x 52 sq micron pixels. Each of the arrays is fabricated using a four phase, double poly, buried n-channel, multi-pinned phase CCD process. Performance data for each sensor is presented.

Dynamics of ultralight aircraft: Motion in vertical gusts

NASA Technical Reports Server (NTRS)

Jones, R. T.

1977-01-01

Gust load calculations are extended to the range of conditions encountered by ultralight aircraft such as hang gliders. Having wing loadings of the order of 5 kg/sq m, these gliders acquire a substantial fraction of the motion of a gust within a distance of 1 or 2 m. Comparative loads and displacements for a small powered airplane having a wing loading of 50 kg sq m and for a commercial jet with 500 kg sq m are shown.

Relationships Among Nightly Sleep Quality, Daily Stress, and Daily Affect.

PubMed

Blaxton, Jessica M; Bergeman, Cindy S; Whitehead, Brenda R; Braun, Marcia E; Payne, Jessic D

2017-05-01

We explored the prospective, microlevel relationship between nightly sleep quality (SQ) and the subsequent day's stress on positive (PA) and negative affect (NA) as well as the moderating relationships between nightly SQ, subsequent stress, and subsequent PA on NA. We investigated whether age moderated these relationships. We collected 56 days of sleep, stress, and affect data using daily diary questionnaires (N = 552). We used multilevel modeling to assess relationships at the between- and within-person levels. Daily increases in SQ and decreases in stress interacted to predict higher daily PA and lower daily NA. Better SQ in older adults enhanced the benefits of PA on the stress-NA relationship more during times of low stress, whereas better sleep in younger adults enhanced the benefits of PA more during times of high stress. Between-person effects were stronger predictors of well-being outcomes than within-person variability. The combination of good SQ and higher PA buffered the impact of stress on NA. The moderating impact of age suggests that sleep and stress play different roles across adulthood. Targeting intervention and prevention strategies to improve SQ and enhance PA could disrupt the detrimental relationship between daily stress and NA. © The Author 2015. Published by Oxford University Press on behalf of The Gerontological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Hydrogen-bond landscapes, geometry and energetics of squaric acid and its mono- and dianions: a Cambridge Structural Database, IsoStar and computational study.

PubMed

Allen, Frank H; Cruz-Cabeza, Aurora J; Wood, Peter A; Bardwell, David A

2013-10-01

As part of a programme of work to extend central-group coverage in the Cambridge Crystallographic Data Centre's (CCDC) IsoStar knowledge base of intermolecular interactions, we have studied the hydrogen-bonding abilities of squaric acid (H2SQ) and its mono- and dianions (HSQ(-) and SQ(2-)) using the Cambridge Structural Database (CSD) along with dispersion-corrected density functional theory (DFT-D) calculations for a range of hydrogen-bonded dimers. The -OH and -C=O groups of H2SQ, HSQ(-) and SQ(2-) are potent donors and acceptors, as indicated by their hydrogen-bond geometries in available crystal structures in the CSD, and by the attractive energies calculated for their dimers with acetone and methanol, which were used as model acceptors and donors. The two anions have sufficient examples in the CSD for their addition as new central groups in IsoStar. It is also shown that charge- and resonance-assisted hydrogen bonds involving H2SQ and HSQ(-) are similar in strength to those made by carboxylate COO(-) acceptors, while hydrogen bonds made by the dianion SQ(2-) are somewhat stronger. The study reinforces the value of squaric acid and its anions as cocrystal formers and their actual and potential importance as isosteric replacements for carboxylic acid and carboxylate functions.

Application of a sodium sulfur cell with dynamic sulfur electrode to a battery system

NASA Astrophysics Data System (ADS)

Tokoi, H.; Takahashi, K.; Shimoyashiki, S.

1992-01-01

The construction and performance of a sodium sulfur battery system with dynamic sulfur electrodes are described. Three cells were first connected in parallel, then two such groups were connected in series. Each cell included a liquid sodium-filled beta-double-prime-alumina tube and a system to feed liquid sulfur into the annular cathode. Low-resistance graphite felt was tightly packed around the beta-double-prime-alumina tube. Sodium pentasulfide was removed from the sulfur electrode. The battery was operated automatically and stably charged and discharged in the two-phase region. The discharged energy was 4372 Wh (capacity 1170 Ah) during a continuous operation of 19.5 h. The discharge/charge energy efficiency of the battery was 82 percent at an averaged current density of 100 mA/sq cm and operating temperature of 350 C. The deviation of the cell current in a parallel chain was less than 7 percent, and this was induced by the difference in internal resistance. In the daily charge/discharge cycle, cell capacity with the dynamic sulfur electrode was 1.5 times higher than that with the static sulfur electrode using the same active surface of beta-double-prime-alumina, because the internal resistance of the former cell was constant regardless of cell capacity. This battery system with a dynamic sulfur electrode can be applied to energy storage systems,such as large scale load leveling systems, electric vehicle batteries, and solar energy systems.

Translation, cultural adaptation and validation into portuguese (Brazil) in Systemic Sclerosis Questionnaire (SySQ).

PubMed

Machado, Roberta Ismael Lacerda; Souto, Lais Medeiros; Freire, Eutilia Andrade Medeiros

2014-01-01

Systemic sclerosis (SSc) is a multisystem disease, autoimmune disorder characterized by a fibroblastic disfunction, with significant impact on quality of life (QoL), measured by instruments or questionnaires that usually were formulated in other languages and in different cultural contexts. Translate into Brazilian Portuguese, cross cultural adaptation and assess the reliability and validity of the Systemic Sclerosis Questionnaire (SySQ). Translation and adaptation: into Portuguese and cross-cultural adaptation was performed in accordance with studies on questionnaire translation methodology into other languages. Reliability: it was analyzed using three interviews with different interviewers, two on the same day (interobserver) and the third within 14 days of the first assessment (intraobserver).Validity was assessed by correlating clinical and quality of life parameters with the domain scores of Sysc. a descriptive analysis of the study sample. Reproducibility was assessed using an intraclass correlation coefficient (ICC). Internal consistency was assessed using Cronbach's alpha coefficient. To assess validity we used Spearman correlation coefficient. Five percent was the level of significance adopted for all statistical tests. In the evaluation of the questionnaires, the results were similar to the original questionnaire, the internal consistency ranging between 0.73 and 0.93 for each item. The interobserver reproducibility was very good for all domains (α = 0.786 to 0.983) and intraobserver agreement was considered very good for general symptoms domain (ICC = 0.916), good for musculoskeletal symptoms domain (ICC = 0.897) and cardiopulmonary domain (ICC = 0.842) and reasonable for gastrointestinal symptoms domain (ICC = 0.686). The Brazilian Portuguese version of SySQ proved to be reproducible and valid for our population, using a recognized methodology for translation and cultural adaptation of questionnaires, as well as to assess the reproducibility and validity.

Abnormal development of tapetum and microspores induced by chemical hybridization agent SQ-1 in wheat.

PubMed

Wang, Shuping; Zhang, Gaisheng; Song, Qilu; Zhang, Yingxin; Li, Zheng; Guo, Jialin; Niu, Na; Ma, Shoucai; Wang, Junwei

2015-01-01

Chemical hybridization agent (CHA)-induced male sterility is an important tool in crop heterosis. To demonstrate that CHA-SQ-1-induced male sterility is associated with abnormal tapetal and microspore development, the cytology of CHA-SQ-1-treated plant anthers at various developmental stages was studied by light microscopy, scanning and transmission electron microscopy, in situ terminal deoxynucleotidyl transferasemediated dUTP nick end-labelling (TUNEL) assay and DAPI staining. The results indicated that the SQ-1-treated plants underwent premature tapetal programmed cell death (PCD), which was initiated at the early-uninucleate stage of microspore development and continued until the tapetal cells were completely degraded; the process of microspore development was then blocked. Microspores with low-viability (fluorescein diacetate staining) were aborted. The study suggests that premature tapetal PCD is the main cause of pollen abortion. Furthermore, it determines the starting period and a key factor in CHA-SQ-1-induced male sterility at the cell level, and provides cytological evidence to further study the mechanism between PCD and male sterility.

Micrometeorological measurements of CH4 and CO2 exchange between the atmosphere and subarctic tundra

NASA Technical Reports Server (NTRS)

Fan, S. M.; Wofsy, S. C.; Bakwin, P. S.; Jacob, D. J.; Anderson, S. M.; Kebabian, P. L.; Mcmanus, J. B.; Kolb, C. E.; Fitzjarrald, D. R.

1992-01-01

Eddy correlation flux measurements and concentration profiles of total hydrocarbons (THC) and CO2 were combined to provide a comprehensive record of atmosphere-biosphere exchange for these gases over a 30-day period in July-August 1988 in the Yukon-Kuskokwin River Delta of Alaska. Over 90 percent of net ecosystem exchanges of THC were due to methane. Lakes and wet meadow tundra provided the major sources of methane. The average fluxes from lake, dry tundra, and wet tundra were 11 +/- 3, 29 +/- 3, and 57 +/- 6 mg CH4/sq m/d, respectively. The mean remission rate for the site was 25 mg/sq m/d. Maximum uptake of CO2 by the tundra was 1.4 gC/sq m/d between 1000 and 1500 hrs, and nocturnal respiration averaged 0.73 gC/sq m/d. Net uptake of CO2 was 0.30 gC/sq m/d for the 30 days of measurement; methane flux accounted for 6 percent of CO2 net uptake.

Brownian dynamics simulations of insulin microspheres formation

NASA Astrophysics Data System (ADS)

Li, Wei; Chakrabarti, Amit; Gunton, James

2010-03-01

Recent experiments have indicated a novel, aqueous process of microsphere insulin fabrication based on controlled phase separation of protein from water-soluble polymers. We investigate the insulin microsphere crystal formation from insulin-PEG-water systems via 3D Brownian Dynamics simulations. We use the two component Asakura-Oosawa model to simulate the kinetics of this colloid polymer mixture. We first perform a deep quench below the liquid-crystal boundary that leads to fractal formation. We next heat the system to obtain a break-up of the fractal clusters and subsequently cool the system to obtain a spherical aggregation of droplets with a relatively narrow size distribution. We analyze the structure factor S(q) to identify the cluster dimension. S(q) crosses over from a power law q dependence of 1.8 (in agreement with DLCA) to 4 as q increases, which shows the evolution from fractal to spherical clusters. By studying the bond-order parameters, we find the phase transition from liquid-like droplets to crystals which exhibit local HCP and FCC order. This work is supported by grants from the NSF and Mathers Foundation.

Similarity Rules for Scaling Solar Sail Systems

NASA Technical Reports Server (NTRS)

Canfield, Stephen L.; Beard, James W., III; Peddieson, John; Ewing, Anthony; Garbe, Greg

2004-01-01

Future science missions will require solar sails on the order 10,000 sq m (or larger). However, ground and flight demonstrations must be conducted at significantly smaller Sizes (400 sq m for ground demo) due to limitations of ground-based facilities and cost and availability of flight opportunities. For this reason, the ability to understand the process of scalability, as it applies to solar sail system models and test data, is crucial to the advancement of this technology. This report will address issues of scaling in solar sail systems, focusing on structural characteristics, by developing a set of similarity or similitude functions that will guide the scaling process. The primary goal of these similarity functions (process invariants) that collectively form a set of scaling rules or guidelines is to establish valid relationships between models and experiments that are performed at different orders of scale. In the near term, such an effort will help guide the size and properties of a flight validation sail that will need to be flown to accurately represent a large, mission-level sail.

Solar system installation at Louisville, Kentucky

NASA Technical Reports Server (NTRS)

1978-01-01

The installation of a solar space heating and domestic hot water system is described. The overall philosophy used was to install both a liquid and a hot air system retrofitted to existing office and combined warehouse building. The 1080 sq. ft. office space is heated first and excess heat is dumped into the warehouse. The two systems offer a unique opportunity to measure the performance and compare results of both air and liquid at one site.

Radical Ions of 3-Styryl-quinoxalin-2-one Derivatives Studied by Pulse Radiolysis in Organic Solvents.

PubMed

Skotnicki, Konrad; De la Fuente, Julio R; Cañete, Álvaro; Berrios, Eduardo; Bobrowski, Krzysztof

2018-04-12

The absorption-spectral and kinetic behaviors of radical ions and neutral hydrogenated radicals of seven 3-styryl-quinoxalin-2(1 H)-one (3-SQ) derivatives, one without substituents in the styryl moiety, four others with electron-donating (R = -CH 3 , -OCH 3 , and -N(CH 3 ) 2 ) or electron-withdrawing (R = -OCF 3 ) substituents in the para position in their benzene ring, and remaining two with double methoxy substituents (-OCH 3 ), however, at different positions (meta/para and ortho/meta) have been studied by UV-vis spectrophotometric pulse radiolysis in neat acetonitrile saturated with argon (Ar) and oxygen (O 2 ) and in 2-propanol saturated with Ar, at room temperature. In acetonitrile solutions, the radical anions (4R-SQ •- ) are characterized by two absorption maxima located at λ max = 470-490 nm and λ max = 510-540 nm, with the respective molar absorption coefficients ε 470-490 = 8500-13 100 M -1 cm -1 and ε 510-540 = 6100-10 300 M -1 cm -1 , depending on the substituent (R). All 4R-SQ •- decay in acetonitrile via first-order kinetics, with the rate constants in the range (1.2-1.5) × 10 6 s -1 . In 2-propanol solutions, they decay predominantly through protonation by the solvent, forming neutral hydrogenated radicals (4R-SQH • ), which are characterized by weak absorption bands with λ max = 480-490 nm. Being oxygen-insensitive, the radical cations (4R-SQ •+ ) are characterized by a strong absorption with λ max = 450-630 nm, depending on the substituent (R). They are formed in a charge-transfer reaction between a radical cation derived from acetonitrile (ACN •+ ) and substituted 3-styryl-quinoxalin-2-one derivatives (4R-SQ) with a pseudo-first-order rate constant k = (2.7-4.7) × 10 5 s -1 measured in solutions containing 0.1 mM 4R-3-SQ. The Hammett equation plot gave a very small negative slope (ρ = -0.08), indicating a very weak influence of the substituents in the benzene ring on the rate of charge-transfer reaction. The decay of 4R-SQ •+ in Ar-saturated acetonitrile solutions occurs with a pseudo-first-order rate constant k = (1.6-6.2) × 10 4 s -1 and, in principle, is not affected by the presence of O 2 , suggesting charge-spin delocalization over the whole 3-SQ molecule. Most of the radiolytically generated transient spectra are reasonably well-reproduced by semiempirical PM3-ZINDO/S (for 4R-SQ •- ) and density functional theory quantum mechanics calculations employing M06-2x hybrid functional together with the def2-TZVP basis set (for 4R-SQ •+ ).

Hall current effects in the Lewis magnetohydrodynamic generator

NASA Technical Reports Server (NTRS)

Nichols, L. D.; Sovie, R. J.

1972-01-01

Data obtained in a magnetohydrodynamic generator are compared with theoretical values calculated by using the Dzung theory. The generator was operated with cesium-seeded argon as the working fluid. The gas temperature varied from 1800 to 2100 K, the gas pressure from 19 to 22 N/sq cm, the Mach number from 0.3 to 0.5, and the magnetic field strength from 0.2 to 1.6 T. The analysis indicates that there is incomplete seed vaporization and that Hall current shorting paths (through the working fluid to ground at both the entrance and exit of the channel) limit generator performance.

The BATSE experiment on the Gamma Ray Observatory: Solar flare hard x ray and gamma-ray capabilities

NASA Technical Reports Server (NTRS)

Fishman, G. J.; Meegan, C. A.; Wilson, R. B.; Parnell, T. A.; Paciesas, W. S.; Pendleton, G. N.; Hudson, H. S.; Matteson, J. L.; Peterson, L. E.; Cline, T. L.

1989-01-01

The Burst and Transient Source Experiment (BATSE) for the Gamma Ray Observatory (GRO) consists of eight detector modules that provide full-sky coverage for gamma-ray bursts and other transient phenomena such as solar flares. Each detector module has a thin, large-area scintillation detector (2025 sq cm) for high time-resolution studies, and a thicker spectroscopy detector (125 sq cm) to extend the energy range and provide better spectral resolution. The total energy range of the system is 15 keV to 100 MeV. These 16 detectors and the associated onboard data system should provide unprecedented capabilities for observing rapid spectral changes and gamma-ray lines from solar flares. The presence of a solar flare can be detected in real-time by BATSE; a trigger signal is sent to two other experiments on the GRO. The launch of the GRO is scheduled for June 1990, so that BATSE can be an important component of the Max '91 campaign.

Advanced System Design Requirements for Large and Small Fixed-wing Aerial Application Systems for Agriculture

NASA Technical Reports Server (NTRS)

Hinely, J. T., Jr.; Boyles, R. Q., Jr.

1979-01-01

Several candidate aircraft configurations were defined over the range of 1000 to 10,000 pounds payload and evaluated over a broad spectrum of agricultural missions. From these studies, baseline design points were selected at 3200 pounds payload for the small aircraft and 7500 pounds for the large aircraft. The small baseline aircraft utilizes a single turboprop powerplant while the large aircraft utilizes two turboprop powerplants. These configurations were optimized for wing loading, aspect ratio, and power loading to provide the best mission economics in representative missions. Wing loading of 20 lb/sq ft was selected for the small aircraft and 25 lb/sq ft for the large aircraft. Aspect ratio of 8 was selected for both aircraft. It was found that a 10% reduction in engine power from the original configurations provided improved mission economics for both aircraft by reducing the cost of the turboprop. Refined configurations incorporate a 675 HP engine in the small aircraft and two 688 HP engines in the large aircraft.

The Peculiar X-ray Transient IGR 16358-4726

NASA Technical Reports Server (NTRS)

Patel, S. K.; Kouveliotou, C.; Tennant, A. F.; Woods, P. M.; King, A.; Ubertini, P.; Winkler, C.; Courvoisier, T.; VanDerKlis, M.; Wachter, S.

2003-01-01

The new transient IGR 16358-4726 was discovered on 2003 March 19 with INTEGRAL. We detected the source serendipitously during our 2003 March 24 observation of SGR 1627 - 4lwith the Chandra X-ray observatory at the 1.7 x 10(exp -l0) ergs/s sq cm flux level ( 2-10 keV) with a very high absorption column (N_H = 3.3 x 10(exp 23)/sq cm and a hard power law spectrum of index 0.5(1). We discovered a very strong flux modulation with a period of 5880(50) s and peak-to-peak pulse fraction of 70(6)% (2-10 keV), clearly visible in the X-ray data. The nature of IGR 16358-4726 remains unresolved. The only neutron star systems known with similar spin periods are low luminosity persistent wind-fed pulsars; if this is a spin period, this transient is a new kind of object. If this is an orbital period, then the system could be a compact Low Mass X-ray Binary (LMXB).

The South American Land Data Assimilation System (SALDAS) 5-Year Retrospective Atmospheric Forcing Datasets

NASA Technical Reports Server (NTRS)

deGoncalves, Luis Gustavo G.; Shuttleworth, William J.; Vila, Daniel; Larroza, Elaine; Bottino, Marcus J.; Herdies, Dirceu L.; Aravequia, Jose A.; De Mattos, Joao G. Z.; Toll, David L.; Rodell, Matthew;