Quasicrystal structure and growth models: discussion of the status quo and the still open questions

NASA Astrophysics Data System (ADS)

Steurer, Walter

2017-02-01

Where are we now in quasicrystal (QC) research more than three decades after Dan Shechtman’s discovery? Do we fully understand the origin of quasiperiodicity, the formation, growth, thermodynamic stability, structure and properties of quasicrystals? First, I will shortly present the status quo, then I will address the still open questions, and identify potential focus areas for future research. Because of the limited space, I will focus on decagonal quasicrystals (DQCs); the status quo for research on icosahedral quasicrystals (IQCs) is comparable.

Discrimination and identification of Q-markers based on 'Spider-web' mode for quality control of traditional Chinese medicine.

PubMed

Jiang, Zhenzuo; Yang, Jing; Wang, Yuefei

2017-12-28

The safety and effectiveness of traditional Chinese medicine (TCM) in clinical practice is directly related to the quality of TCM. And, the quality control of TCM is a pivotal issue to the quality of TCM, but also an obstacle impeding the modernization of TCM. The purpose of this work is to compile and develop a strategy based on discrimination and identification of quality markers (Q-markers) for quality control of TCM. Mainly established by seven variables derived from four dimensions including content, stability, pharmacokinetics and pharmacology, the 'Spider-web' mode was undertaken to assess the Q-marker property of candidate compounds originated from TCM by taking regression area (A) and coefficient variation (CV) of the tested compounds into account. The importance index (ImI), ImI = A × 1/CV, was suggested to focus Q-markers. The compounds with larger regression area (A) and less coefficient variation (CV) are preferentially adopted as Q-markers, which should possess the satisfactory properties of content, stability, pharmacokinetics and pharmacological activity. To the contrary, the compounds are excluded on the grounds of the unsatisfactory Q-markers' property, less regression area (A) and larger coefficient variation (CV), which cannot represent the quality of TCM. The 'Spider-web' mode can filter out the redundant constituents and focus on the key indexes of quality control - Q-markers. The screened Q-markers possess the optimal integrated properties of content, stability, pharmacokinetics and pharmacology among the numerous and complicated ingredients of TCM, which can comprehensively characterize inherent quality of TCM. In summary, the novel strategy established in this work provides a valuable perspective for the quality control of TCM. Copyright © 2017 Elsevier GmbH. All rights reserved.

Humid site stabilization and closure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cutshall, N.H.

1981-01-01

The purpose of the work described here is to identify and evaluate the importance of factors that are expected to dictate the nature of site stabilization and closure requirements. Subsequent efforts will plan for implementation of such requirements. Two principal areas of site stabilization and closure effort will be pursued initially - geological management and vegetation management. The geological effort will focus on chemical weathering and surficial erosion. Such catastrophic geologic events as landslides, flooding, earthquakes, volcanos, etc. are already considered in site selection and operation and these factors will not be emphasized initially. Vegetation management will be designed tomore » control erosion, to minimize nuclide mobilization by roots and to be compatible with natural successional pressures. It is anticipated that the results of this work will be important both to site selection and operation as well as the actual stabilization and closure procedure.« less

Method for measuring integrated sensitivity of solar cells and multielement photoconverters using an X-Y scanner

NASA Astrophysics Data System (ADS)

Naumov, V. V.; Grebenshchikov, O. A.; Zalesskii, V. B.

2006-09-01

We describe a method for automated measurement of the integrated sensitivity of solar cells (SCs) and multielement photoconverters (MPCs) using an experimental apparatus including a Pentium III personal computer (PC), an HP-34401A digital multimeter (DM), a stabilized radiation source (SRS), a controllable focusing system, an X-Y positioning device based on CD-RW optical disk storage devices. The method provides high accuracy in measuring the size of photosensitive areas of the solar cells and multielement photoconverters and inhomogeneities in their active regions, which makes it possible to correct the production process in the development stage and during fabrication of test prototypes for the solar cells and multielement photoconverters. The radiation power from the stabilized radiation source was ≤1 W; the ranges of the scanning steps along the X, Y coordinates were 10 100 µm, the range of the transverse cross sectional diameters of the focused radiation beam was 10 100 µm, the measurable photocurrents were 10-9 A to 2 A; scanning rate along the X, Y coordinates, ≤100 mm/sec; relative mean-square error (RMSE) for measurement of the integrated sensitivity of the solar cells, 0.2 ≤ γS int ≤ 0.9% in the ranges of measurable photocurrents 1 mA ≤ Iph ≤ 750 mA and areas 0.1 ≤ A ≤ 25 cm2 for number of measurements equal to ≤ 2· 105; instability of the radiation power (luminosity) ≤ 0.08% for 1 h or ≤ 0.4% for 8 h continuous operation; stabilized power range for the stabilized radiation source, 10-2 102 W. The software was written in Delphi 7.0.

Sorbent Structural Impacts Due to Humidity on Carbon Dioxide Removal Sorbents for Advanced Exploration Systems

NASA Technical Reports Server (NTRS)

Watson, David; Knox, James C.; West, Phillip; Stanley, Christine M.; Bush, Richard

2015-01-01

The Life Support Systems Project (LSSP) under the Advanced Exploration Systems (AES) program builds upon the work performed under the AES Atmosphere Resource Recovery and Environmental Monitoring (ARREM) project focusing on the numerous technology development areas. The CO2 removal and associated air drying development efforts are focused on improving the current state-of-the-art system on the International Space Station (ISS) utilizing fixed beds of sorbent pellets by seeking more robust pelletized sorbents, evaluating structured sorbents, and examining alternate bed configurations to improve system efficiency and reliability. A component of the CO2 removal effort encompasses structural stability testing of existing and emerging sorbents. Testing will be performed on dry sorbents and sorbents that have been conditioned to three humidity levels. This paper describes the sorbent structural stability screening efforts in support of the LSS Project within the AES Program.

Management Development Programs: The Effects of Management Level and Corporate Strategy. [and] Invited Reaction: Level and Strategy Should and Do Make a Difference!

ERIC Educational Resources Information Center

Blakely, Gerald L.; And Others

1994-01-01

Consensus of survey responses from 155 of 600 human resource managers was as follows: management development programs emphasized technical skills at lower levels, entrepreneurial skills at senior levels; organizations with corporate growth strategies focused on more areas than those with stability or retrenchment strategies. (Muschewske's reaction…

Degeneracy in NLP and the development of results motivated by its presence

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fiacco, A.; Liu, J.

We study notions of nondegeneracy and several levels of increasing degeneracy from the perspective of the local behavior of a local solution of a nonlinear program when problem parameters are slightly perturbed. This overview may be viewed as a structured survey of sensitivity and stability results: the focus is on progressive levels of degeneracy. We note connections of nondegeneracy with the convergence of algorithms and observe the striking parallel between the effects of nondegeneracy and degeneracy on optimality conditions, stability analysis and algorithmic convergence behavior. Although our orientation here is primarily interpretive and noncritical, we conclude that more effort ismore » needed to unify optimality, stability and convergence theory and more results are needed in all three areas for radically degenerate problems.« less

LISA Beyond Einstein: From the Big Bang to Black Holes. LISA Technology Development at GSFC

NASA Technical Reports Server (NTRS)

Thorpe, James Ira

2008-01-01

This viewgraph presentation reviews the work that has been ongoing at the Goddard Space Flight Center (GSFC) in the development of the technology to be used in the Laser Interferometer Space Antenna (LISA) spacecrafts. The prime focus of LISA technology development efforts at NASA/GSFC has been in LISA interferometry. Specifically efforts have been made in the area of laser frequency noise mitigation. Laser frequency noise is addressed through a combination of stabilization and common-mode rejection. Current plans call for two stages of stabilization, pre-stabilization to a local frequency reference and further stabilization using the constellation as a frequency reference. In order for these techniques to be used simultaneously, the pre-stabilization step must provide an adjustable frequency offset. This presentation reports on a modification to the standard modulation/demodulation technique used to stabilize to optical cavities that generates a frequency-tunable reference from a fixed length cavity. This technique requires no modifications to the cavity itself and only minor modifications to the components. The measured noise performance and dynamic range of the laboratory prototype meet the LISA requirements.

Optics for multimode lasers with elongated depth of field

NASA Astrophysics Data System (ADS)

Laskin, Alexander; Laskin, Vadim; Ostrun, Aleksei

2017-02-01

Modern multimode high-power lasers are widely used in industrial applications and control of their radiation, especially by focusing, is of great importance. Because of relatively low optical quality, characterized by high values of specifications Beam Parameter Product (BPP) or M², the depth of field by focusing of multimode laser radiation is narrow. At the same time laser technologies like deep penetration welding, cutting of thick metal sheets get benefits from elongated depth of field in area of focal plane, therefore increasing of zone along optical axis with minimized spot size is important technical task. As a solution it is suggested to apply refractive optical systems splitting an initial laser beam into several beamlets, which are focused in different foci separated along optical axis with providing reliable control of energy portions in each separate focus, independently of beam size or mode structure. With the multi-focus optics, the length of zone of material processing along optical axis is defined rather by distances between separate foci, which are determined by optical design of the optics and can be chosen according to requirements of a particular laser technology. Due to stability of the distances between foci there is provided stability of a technology process. This paper describes some design features of refractive multi-focus optics, examples of real implementations and experimental results will be presented as well.

A GIS-based susceptibility map for landslides at the Franconian Alb, Germany

NASA Astrophysics Data System (ADS)

Jaeger, Daniel; Wilde, Martina; Lorenz, Michael; Terhorst, Birgit; Neuhäuser, Bettina; Damm, Bodo; Bemm, Stefan

2014-05-01

In general, slopes of cuesta scarps like the Franconian Alb are highly prone to slide activity due to susceptible geological and geomorphological conditions. The geological setting with alternating permeable and non-permeable bedrock results in the characteristic cuesta landforms of almost flat backslopes and steeper front slopes. Furthermore, this bipartite structure leads to a strong disposition for mass movements. The slopes of the study area near the town of Ebermannstadt are affected by different types of mass movements, such as topples, slides, lateral spreads and flows, either in single or in combined occurrence. In the years 1625, 1957, 1961 and 1979, four large landslides took place in the area of Ebermannstadt, reaching close to the town limits and causing major destructions to traffic facilities. In the study area, slopes are covered by debris and slide masses, thus they are prone to remobilization and further mass movements. In order to assess hazardous areas, a GIS-based susceptibility modelling was generated for the study area. The susceptibtibility modeling was processed with the slope stability model SINMAP (Stability Index Mapping), developed by TARBOTON (1997) and PACK et al. (1999). As SINMAP was particularly designed to model shallow translational slides, it should be well designed for describing the conditions of the study area in a sufficient way. SINMAP is based on the "infinite slope stability model" by HAMMONT et al. (1992) and MONTGOMERY & DIETRICH (1994), which focuses on the relation of stabilizing (cohesiveness, friction angle) and destabilizing (gravitation) factors on a plain surface. By adding a slope gradient, as well as soil mechanical and climatical data, indices of slope stabilities are calculated. For a more detailed modeling of the slope conditions, SINMAP computes different "calibration regions", which merge similar parameters of soil, land-use, vegetation, and geology. Due to the fact that vegetation, land-use, and soils only show minor differences on the slopes of the study area and therefore have no significant impact on the slope stability in the applied modeling, geology becomes the most important input factor. Therefore, first calculations are based on the main geological units drawn in the geological map, such as limestone, clay, sandstone and debris. However, the results obtained were not sufficient, as several areas of known instability were calculated as rather stable slope areas. This was due to an underrepresentation of debris and slide masses in the geological map and the models' calculation. In order to improve the modeling process, geological standard units were further differentiated, with the debris cover and its soil mechanical parameters considered in greater detail. These adjustments not only led to significantly improved modeling results in the study area, but also create a more realistic basis for SINMAP calculations in all cuesta landscapes. HAMMONT, C., HALL, D., MILLER, S., SWETIK, P. (1992): Level I Stability Analysis (LISA) Documentation for version 2.0. General Technical report INT-285, USDA Forest Service Intermountain Research Station 190p. MONTGOMERY, D. R. & DIETRICH, W. E. (1994): A physically based model for the topographic control on shallow landsliding. Water Resources Research 30/4, p 1153-1171. PACK, R. T., TARBOTON, D. G. & GOODWIN, C.N. (1999): SINMAP - A Stability Index Approach to Terrain Stability Hazard Mapping, User's Manual. Forest Renewal B.C., 65p. TARBOTON, G.D. (1997): A new method for the determination of flow directions and upslope areas in grid digital elevation models. Water Resources Research 33/2, p 309-319.

Computational mechanics research and support for aerodynamics and hydraulics at TFHRC year 1 quarter 4 progress report.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lottes, S.A.; Kulak, R.F.; Bojanowski, C.

2011-12-09

The computational fluid dynamics (CFD) and computational structural mechanics (CSM) focus areas at Argonne's Transportation Research and Analysis Computing Center (TRACC) initiated a project to support and compliment the experimental programs at the Turner-Fairbank Highway Research Center (TFHRC) with high performance computing based analysis capabilities in August 2010. The project was established with a new interagency agreement between the Department of Energy and the Department of Transportation to provide collaborative research, development, and benchmarking of advanced three-dimensional computational mechanics analysis methods to the aerodynamics and hydraulics laboratories at TFHRC for a period of five years, beginning in October 2010. Themore » analysis methods employ well-benchmarked and supported commercial computational mechanics software. Computational mechanics encompasses the areas of Computational Fluid Dynamics (CFD), Computational Wind Engineering (CWE), Computational Structural Mechanics (CSM), and Computational Multiphysics Mechanics (CMM) applied in Fluid-Structure Interaction (FSI) problems. The major areas of focus of the project are wind and water effects on bridges - superstructure, deck, cables, and substructure (including soil), primarily during storms and flood events - and the risks that these loads pose to structural failure. For flood events at bridges, another major focus of the work is assessment of the risk to bridges caused by scour of stream and riverbed material away from the foundations of a bridge. Other areas of current research include modeling of flow through culverts to assess them for fish passage, modeling of the salt spray transport into bridge girders to address suitability of using weathering steel in bridges, CFD analysis of the operation of the wind tunnel in the TFCHR wind engineering laboratory, vehicle stability under high wind loading, and the use of electromagnetic shock absorbers to improve vehicle stability under high wind conditions. This quarterly report documents technical progress on the project tasks for the period of July through September 2011.« less

Dynamics and statics of nonaxisymmetric liquid bridges

NASA Technical Reports Server (NTRS)

Alexander, J. Iwan D.; Resnick, Andy; Zhang, Yiqiang; Fedoseyev, A.

1994-01-01

We finished the construction of the experimental apparatus and the design and testing of some of the visualization and data acquisition techniques. Experimental work focused on three areas: force measurements, loss of stability to nonaxisymmetric bridges, and vibration behavior. The experimental work is summarized in section 2. Selected results from our force measurement experiments are outlined in section 3. In addition we worked on the theory of the dynamic stability of axisymmetric bridges and undertook numerical simulation of the effects of inclined gravity vectors on the minimum volume stability limit for static bridges. The results and status of our theoretical work and numerical simulation are described in section 4. Papers published and in preparation, conference presentations, etc., are described in section 5. Work planned for the third year is discussed in section 6. References cited in the report are listed in section 7.

Development of a High-Stability Microstrip-based L-band Radiometer for Ocean Salinity Measurements

NASA Technical Reports Server (NTRS)

Pellerano, Fernando A.; Horgan, Kevin A.; Wilson, William J.; Tanner, Alan B.

2004-01-01

The development of a microstrip-based L-band Dicke radiometer with the long-term stability required for future ocean salinity measurements to an accuracy of 0.1 psu is presented. This measurement requires the L-band radiometers to have calibration stabilities of less than or equal to 0.05 K over 2 days. This research has focused on determining the optimum radiometer requirements and configuration to achieve this objective. System configuration and component performance have been evaluated with radiometer test beds at both JPL and GSFC. The GSFC testbed uses a cryogenic chamber that allows long-term characterization at radiometric temperatures in the range of 70 - 120 K. The research has addressed several areas including component characterization as a function of temperature and DC bias, system linearity, optimum noise diode injection calibration, and precision temperature control of components. A breadboard radiometer, utilizing microstrip-based technologies, has been built to demonstrate this long-term stability.

Flood risks in urbanized areas - multi-sensoral approaches using remotely sensed data for risk assessment

NASA Astrophysics Data System (ADS)

Taubenböck, H.; Wurm, M.; Netzband, M.; Zwenzner, H.; Roth, A.; Rahman, A.; Dech, S.

2011-02-01

Estimating flood risks and managing disasters combines knowledge in climatology, meteorology, hydrology, hydraulic engineering, statistics, planning and geography - thus a complex multi-faceted problem. This study focuses on the capabilities of multi-source remote sensing data to support decision-making before, during and after a flood event. With our focus on urbanized areas, sample methods and applications show multi-scale products from the hazard and vulnerability perspective of the risk framework. From the hazard side, we present capabilities with which to assess flood-prone areas before an expected disaster. Then we map the spatial impact during or after a flood and finally, we analyze damage grades after a flood disaster. From the vulnerability side, we monitor urbanization over time on an urban footprint level, classify urban structures on an individual building level, assess building stability and quantify probably affected people. The results show a large database for sustainable development and for developing mitigation strategies, ad-hoc coordination of relief measures and organizing rehabilitation.

Steps Towards Understanding Large-scale Deformation of Gas Hydrate-bearing Sediments

NASA Astrophysics Data System (ADS)

Gupta, S.; Deusner, C.; Haeckel, M.; Kossel, E.

2016-12-01

Marine sediments bearing gas hydrates are typically characterized by heterogeneity in the gas hydrate distribution and anisotropy in the sediment-gas hydrate fabric properties. Gas hydrates also contribute to the strength and stiffness of the marine sediment, and any disturbance in the thermodynamic stability of the gas hydrates is likely to affect the geomechanical stability of the sediment. Understanding mechanisms and triggers of large-strain deformation and failure of marine gas hydrate-bearing sediments is an area of extensive research, particularly in the context of marine slope-stability and industrial gas production. The ultimate objective is to predict severe deformation events such as regional-scale slope failure or excessive sand production by using numerical simulation tools. The development of such tools essentially requires a careful analysis of thermo-hydro-chemo-mechanical behavior of gas hydrate-bearing sediments at lab-scale, and its stepwise integration into reservoir-scale simulators through definition of effective variables, use of suitable constitutive relations, and application of scaling laws. One of the focus areas of our research is to understand the bulk coupled behavior of marine gas hydrate systems with contributions from micro-scale characteristics, transport-reaction dynamics, and structural heterogeneity through experimental flow-through studies using high-pressure triaxial test systems and advanced tomographical tools (CT, ERT, MRI). We combine these studies to develop mathematical model and numerical simulation tools which could be used to predict the coupled hydro-geomechanical behavior of marine gas hydrate reservoirs in a large-strain framework. Here we will present some of our recent results from closely co-ordinated experimental and numerical simulation studies with an objective to capture the large-deformation behavior relevant to different gas production scenarios. We will also report on a variety of mechanically relevant test scenarios focusing on effects of dynamic changes in gas hydrate saturation, highly uneven gas hydrate distributions, focused fluid migration and gas hydrate production through depressurization and CO2 injection.

Demonstration of ATG Process for Stabilizing Mercury (<260 ppm) Contaminated Mixed Waste. Mixed Waste Focus Area. OST Reference # 2407

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

1999-09-01

Mercury contaminated wastes in many forms are present at various U. S. Department of Energy (DOE) sites. Based on efforts led by the Mixed Waste Focus Area (MWFA) and its Mercury Working Group (HgWG), the inventory of wastes contaminated with <260 ppm mercury and with radionuclides stored at various DOE sites is estimated to be approximately 6,000 m 3). At least 26 different DOE sites have this type of mixed low-level waste in their storage facilities. Extraction methods are required to remove mercury from waste containing >260 ppm levels, but below 260 ppm Hg contamination levels the U. S. Environmentalmore » Protection Agency (EPA) does not require removal of mercury from the waste. Steps must still be taken, however, to ensure that the final waste form does not leach mercury in excess of the limit for mercury prescribed in the Resource Conservation and Recovery Act (RCRA) when subjected to the Toxicity Characteristic Leaching Procedure (TCLP). At this time, the limit is 0.20 mg/L. However, in the year 2000, the more stringent Universal Treatment Standard (UTS) of 0.025 mg/L will be used as the target endpoint. Mercury contamination in the wastes at DOE sites presents a challenge because it exists in various forms, such as soil, sludges, and debris, as well as in different chemical species of mercury. Stabilization is of interest for radioactively contaminated mercury waste (<260 ppm Hg) because of its success with particular wastes, such as soils, and its promise of applicability to a broad range of wastes. However, stabilization methods must be proven to be adequate to meet treatment standards. It must also be proven feasible in terms of economics, operability, and safety. To date, no standard method of stabilization has been developed and proven for such varying waste types as those within the DOE complex.« less

Charting Russia's Future in the Post-Soviet Era. Eighth Edition. Teacher Resource Book [and Student Text]. Public Policy Debate in the Classroom. Choices for the 21st Century.

ERIC Educational Resources Information Center

Fox, Sarah Cleveland

Russia struggle with questions of identity and economic stability sine ending its Cold War relationship with the United States. In this unit students are asked to see the world through Russian eyes and to contemplate Russian choices in the areas of economic development, political organization, and foreign policy. The unit focuses on three distinct…

Stabilizing the Debate between Population-Centric and Enemy-Centric Counterinsurgency : Success Demands a Balanced Approach

DTIC Science & Technology

2011-06-10

Plan increased the focus on population protection and control while maintaining an offensive, aggressive disposition against the insurgency.15 Large...dominate the populated areas and to build up a feeling of complete security, which would in time result in a steady and increasing flow of...police, and military authorities was undesirable and did not result in timely and accurate decisions and their associated implementation. General

Mid-Holocene stabilization of the Karakum and Kyzylkum sand seas, central Asia - evidence from OSL ages

NASA Astrophysics Data System (ADS)

Maman, Shimrit; Tsoar, Haim; Blumberg, Dan G.; Porat, Naomi

2013-04-01

Sand seas (ergs) are large areas of deserts covered by wind-swept sand with varying degrees of vegetation cover. The Kyzylkum and Karakum ergs have accumulated in the Turan basin, northwest of the Hindu Kush range, and span from south Turkmenistan to the Syrdarya River in Kazakhstan. These ergs are dissected by the Amudarya River; To the north lies the Kyzylkum (red sands) and to the south the Karakum (black sands). This area is understudied, and little information has been published regarding the sands stabilization processes and deposition ages. This research focuses on identifying and mapping the ergs of Central Asia and analyzing the climate factors that set the dunes into motion and that stabilized them. A variety of spaceborne imagery with varying spectral and spatial resolutions was used. These images provide the basis for mapping sand distribution, dune forms, and vegetation cover. Wilson (1973) defined these ergs as active based on precipitation. Our results show that they are mostly stabilized, with an estimated area of ~260,000 sq. Km for Kara-Kum , and ~195,500 sq. Km for the Kyzyl-Kum . Meteorological analysis of wind and precipitation data indicate a low wind energy environment (DP<200) and sufficient rainfall (>100 mm) to which is essential for vegetation cover. We present the first optically stimulated luminescence (OSL) ages from the upper meter of 14 exposed sections from both ergs. The age of the sand samples was determined as ~Mid-Holocene by OSL, which provides an insight into past climate characteristics. These ages indicate extensive sand and dune stabilization during the Mid-Holocene. GIS analysis was performed in parallel with field work to validate and verify the results. The OSL ages, coupled with a compilation of regional palaeoclimatic data, corroborate and reinforce the previously proposed Mid-Holocene Liavliakan phase, known to reflect a warmer, wetter, less windy climate than persists today and that resulted in dune stabilization around Mid-Holocene. This study emphasizes the importance of regional climatic control on aeolian activity and is the first to show when these vast sand seas were stabilized.

Status of the Combustion Devices Injector Technology Program at the NASA MSFC

NASA Technical Reports Server (NTRS)

Jones, Gregg; Protz, Christopher; Trinh, Huu; Tucker, Kevin; Nesman, Tomas; Hulka, James

2005-01-01

To support the NASA Space Exploration Mission, an in-house program called Combustion Devices Injector Technology (CDIT) is being conducted at the NASA Marshall Space Flight Center (MSFC) for the fiscal year 2005. CDIT is focused on developing combustor technology and analysis tools to improve reliability and durability of upper-stage and in-space liquid propellant rocket engines. The three areas of focus include injector/chamber thermal compatibility, ignition, and combustion stability. In the compatibility and ignition areas, small-scale single- and multi-element hardware experiments will be conducted to demonstrate advanced technological concepts as well as to provide experimental data for validation of computational analysis tools. In addition, advanced analysis tools will be developed to eventually include 3-dimensional and multi- element effects and improve capability and validity to analyze heat transfer and ignition in large, multi-element injectors.

Latest development on RNA-based drugs and vaccines.

PubMed

Lundstrom, Kenneth

2018-06-01

Drugs and vaccines based on mRNA and RNA viruses show great potential and direct translation in the cytoplasm eliminates chromosomal integration. Limitations are associated with delivery and stability issues related to RNA degradation. Clinical trials on RNA-based drugs have been conducted in various disease areas. Likewise, RNA-based vaccines for viral infections and various cancers have been subjected to preclinical and clinical studies. RNA delivery and stability improvements include RNA structure modifications, targeting dendritic cells and employing self-amplifying RNA. Single-stranded RNA viruses possess self-amplifying RNA, which can provide extreme RNA replication in the cytoplasm to support RNA-based drug and vaccine development. Although oligonucleotide-based approaches have demonstrated potential, the focus here is on mRNA- and RNA virus-based methods.

Shape-Memory Polymers for Biomedical Applications

NASA Astrophysics Data System (ADS)

Yakacki, Christopher M.; Gall, Ken

Shape-memory polymers (SMPs) are a class of mechanically functional "smart" materials that have generated substantial interest for biomedical applications. SMPs offer the ability to promote minimally invasive surgery, provide structural support, exert stabilizing forces, elute therapeutic agents, and biodegrade. This review focuses on several areas of biomedicine including vascular, orthopedic, and neuronal applications with respect to the progress and potential for SMPs to improve the standard of treatment in these areas. Fundamental studies on proposed biomedical SMP systems are discussed with regards to biodegradability, tailorability, sterilization, and biocompatibility. Lastly, a proposed research and development pathway for SMP-based biomedical devices is proposed based on trends in the recent literature.

Nanoporous Metals with Structural Hierarchy: A Review

DOE PAGES

Juarez, Theresa; Biener, Juergen; Weissmüller, Jörg; ...

2017-08-09

Nanoporous (np) metals have generated much interest since they combine several desirable material characteristics, such as high surface area, mechanical size effects, and high conductivity. Most of the research has been focused on np Au due to its relatively straightforward synthesis, chemical stability, and many promising applications in the fields of catalysis and actuation. Other materials, such as np-Cu, Ag, and Pd have also been studied. Here, this review discusses recent advances in the field of np metals, focusing on new research areas that implement and leverage structural hierarchy while using np metals as their base structural constituents. First, wemore » focus on single-element porous metals that are made of np metals at the fundamental level, but synthesized with additional levels of porosity. Second, we discuss the fabrication of composite structures, which use auxiliary materials to enhance the properties of np metals. Important applications of these hierarchical materials, especially in the fields of catalysis and electrochemistry, are also reviewed. Lastly, we conclude with a discussion about future opportunities for the advancement and application of np metals.« less

Nanoporous Metals with Structural Hierarchy: A Review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Juarez, Theresa; Biener, Juergen; Weissmüller, Jörg

Nanoporous (np) metals have generated much interest since they combine several desirable material characteristics, such as high surface area, mechanical size effects, and high conductivity. Most of the research has been focused on np Au due to its relatively straightforward synthesis, chemical stability, and many promising applications in the fields of catalysis and actuation. Other materials, such as np-Cu, Ag, and Pd have also been studied. Here, this review discusses recent advances in the field of np metals, focusing on new research areas that implement and leverage structural hierarchy while using np metals as their base structural constituents. First, wemore » focus on single-element porous metals that are made of np metals at the fundamental level, but synthesized with additional levels of porosity. Second, we discuss the fabrication of composite structures, which use auxiliary materials to enhance the properties of np metals. Important applications of these hierarchical materials, especially in the fields of catalysis and electrochemistry, are also reviewed. Lastly, we conclude with a discussion about future opportunities for the advancement and application of np metals.« less

Joint Force Quarterly. Issue 64, 1st Quarter 2012

DTIC Science & Technology

2012-01-01

Zad out, and the district gover - nor and army came in. Now kids there go to school. So now even Now Zad is one of the proof-of-concept areas. Does...compared to PRT operations since their aim is also to improve security, stability, and gover - nance through multiple agencies in coordina- tion with the...Mauritius focused on developing a manufac- turing hub and financial and tourism service centers, with a $750-million investment; and two in Nigeria

Stability of plasma treated superhydrophobic surfaces under different ambient conditions.

PubMed

Chen, Faze; Liu, Jiyu; Cui, Yao; Huang, Shuai; Song, Jinlong; Sun, Jing; Xu, Wenji; Liu, Xin

2016-05-15

Plasma hydrophilizing of superhydrophobic substrates has become an important area of research, for example, superhydrophobic-(super)hydrophilic patterned surfaces have significant practical applications such as lab-on-chip systems, cell adhesion, and control of liquid transport. However, the stability of plasma-induced hydrophilicity is always considered as a key issue since the wettability tends to revert back to the untreated state (i.e. aging behavior). This paper focuses on the stability of plasma treated superhydrophobic surface under different ambient conditions (e.g. temperature and relative humidity). Water contact angle measurement and X-ray photoelectron spectroscopy are used to monitor the aging process. Results show that low temperature and low relative humidity are favorable to retard the aging process and that pre-storage at low temperature (-10°C) disables the treated surface to recover superhydrophobicity. When the aging is performed in water, a long-lasting hydropholicity is obtained. As the stability of plasma-induced hydrophilcity over a desired period of time is a very important issue, this work will contribute to the optimization of storage conditions of plasma treated superhydrophobic surfaces. Copyright © 2016 Elsevier Inc. All rights reserved.

Some Thoughts on Stability in Nonlinear Periodic Focusing Systems

DOE R&D Accomplishments Database

McMillan, E. M.

1967-09-05

A brief discussion is given of the long-term stability of particle motions through periodic focusing structures containing lumped nonlinear elements. A method is presented whereby one can specify the nonlinear elements in such a way as to generate a variety of structures in which the motion has long-term stability.

Stochastic analysis of motor-control stability, polymer based force sensing, and optical stimulation as a preventive measure for falls

NASA Astrophysics Data System (ADS)

Landrock, Clinton K.

Falls are the leading cause of all external injuries. Outcomes of falls include the leading cause of traumatic brain injury and bone fractures, and high direct medical costs in the billions of dollars. This work focused on developing three areas of enabling component technology to be used in postural control monitoring tools targeting the mitigation of falls. The first was an analysis tool based on stochastic fractal analysis to reliably measure levels of motor control. The second focus was on thin film wearable pressure sensors capable of relaying data for the first tool. The third was new thin film advanced optics for improving phototherapy devices targeting postural control disorders. Two populations, athletes and elderly, were studied against control groups. The results of these studies clearly show that monitoring postural stability in at-risk groups can be achieved reliably, and an integrated wearable system can be envisioned for both monitoring and treatment purposes. Keywords: electro-active polymer, ionic polymer-metal composite, postural control, motor control, fall prevention, sports medicine, fractal analysis, physiological signals, wearable sensors, phototherapy, photobiomodulation, nano-optics.

Isoelectric focusing of red blood cells in a density gradient stabilized column

NASA Technical Reports Server (NTRS)

Smolka, A. J. K.; Miller, T. Y.

1980-01-01

The effects of Ficoll and cell application pH on red blood cell electrophoretic mobility and focusing pH were investigated by focusing cells in a density gradient stabilized column. Sample loading, cell dispersion, column conductivity, resolution of separation, and the effect of Ampholines were examined.

An overview of preparation and applications of stabilized zero-valent iron nanoparticles for soil and groundwater remediation.

PubMed

Zhao, Xiao; Liu, Wen; Cai, Zhengqing; Han, Bing; Qian, Tianwei; Zhao, Dongye

2016-09-01

Nano-scale zero-valent iron (nZVI) is one of the most intensively studied materials for environmental cleanup uses over the past 20 years or so. Freshly prepared nZVI is highly reactive due to its high specific surface area and strong reducing power. Over years, the classic borohydride reduction method for preparing nZVI has been modified by use of various stabilizers or surface modifiers to acquire more stable and soil deliverable nZVI for treatment of different organic and inorganic contaminants in water and soil. While most studies have been focused on testing nZVI for water treatment, the greater potential or advantage of nZVI appears to be for in situ remediation of contaminated soil and groundwater by directly delivering stabilized nZVI into the contaminated subsurface as it was proposed from the beginning. Compared to conventional remediation practices, the in situ remediation technique using stabilized nZVI offers some unique advantages. This work provides an update on the latest development of stabilized nZVI for various environmental cleanup uses, and overviews the evolution and environmental applications of stabilized nZVI. Commonly used stabilizers are compared and the stabilizing mechanisms are discussed. The effectiveness and constraints of the nZVI-based in situ remediation technology are summarized. This review also reveals some critical knowledge gaps and research needs, such as interactions between delivered nZVI and the local biogeochemical conditions. Copyright © 2016 Elsevier Ltd. All rights reserved.

How the gas hydrate system gives insight into subduction wedge dewatering processes in a zone of highly-oblique convergence on the southern Hikurangi margin of New Zealand

NASA Astrophysics Data System (ADS)

Crutchley, Gareth; Klaeschen, Dirk; Pecher, Ingo; Henrys, Stuart

2017-04-01

The southern end of New Zealand's Hikurangi subduction margin is characterised by highly-oblique convergence as it makes a southward transition into a right-lateral transform plate boundary at the Alpine Fault. Long-offset seismic data that cross part of the offshore portion of this transition zone give new insight into the nature of the plate boundary. We have carried out 2D pre-stack depth migrations, with an iterative reflection tomography to update the velocity field, on two seismic lines in this area to investigate fluid flow processes that have implications for the mechanical stability of the subduction interface. The results show distinct and focused fluid expulsion pathways from the subduction interface to the shallow sub-surface. For example, on one of the seismic lines there is a clear disruption of the gas hydrate system at its intersection with a splay fault - a clear indication of focused fluid release from the subduction interface. The seismic velocities derived from tomography also highlight a broad, pronounced low velocity zone beneath the deforming wedge that we interpret as a thick zone of gas-charged fluids that may have important implications for the long-term frictional stability of the plate boundary in this area. The focused flow upward toward the seafloor has the potential to result in the formation of concentrated gas hydrate deposits. Our on-going work on these data will include amplitude versus offset analysis in an attempt to better characterise the nature of the subduction interface, the fluids in that region, and also the shallower gas hydrate system.

Breakthroughs in photonics 2013: X-ray optics

DOE PAGES

Soufli, Regina

2014-04-01

Here, this review discusses the latest advances in extreme ultraviolet/X-ray optics development, which are motivated by the availability and demands of new X-ray sources and scientific and industrial applications. Among the breakthroughs highlighted are the following: i) fabrication, metrology, and mounting technologies for large-area optical substrates with improved figure, roughness, and focusing properties; ii) multilayer coatings with especially optimized layer properties, achieving improved reflectance, stability, and out-of-band suppression; and iii) nanodiffractive optics with improved efficiency and resolution.

Clearwater Focus Watershed; Nez Perce Tribe, 2002-2003 Annual Report.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jones, Ira

2004-01-01

The Nez Perce Tribe Department of Fisheries Resource Management, Watershed Division, approaches watershed restoration with a goal to protect, restore, and enhance a connected network of functioning habitat types capable of supporting all fish life stages. Its goal is also to re-establish normal patters of production, dispersal, and exchange of genetic information within the 1855 Treaty Area. The Nez Perce Tribe began watershed restoration projects within the Clearwater River Subbasin in 1996. Progress has been made in restoring the sub-basin by excluding cattle from critical riparian areas through fencing, stabilizing streambanks, decommissioning roads, and upgrading culverts. Coordination of these projectsmore » is critical to the success of the restoration of the sub-basin. Coordination includes: within department coordination, sub-basin assessment and planning, and treaty area coordination.« less

US-RERTR Advanced Fuel Development Plans : 1999.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meyer, M. K.

1998-10-22

Twelve fuel alloys were included in the very-high-density RERTR-1 and RERTR-2 microplate irradiation experiments. Experience gained during fabrication and results from the post-irradiation examination of these fuels has allowed us to narrow the focus of our fuel development efforts in preparation for the next set of irradiation experiments. Specific technical problems in both the areas of fuel fabrication and irradiation performance remain to be addressed. Examples of these are powder fabrication, fuel phase gamma stability versus density, and fuel-matrix interaction. In order to more efficiently address metal alloy fuel performance issues, work will continue on establishing a theoretical basis formore » alloy stability and metal alloy dispersion fuel irradiation performance. Plans to address these fuel development issues in the coming year will be presented.« less

Slope Reinforcement with the Utilization of the Coal Waste Anthropogenic Material

NASA Astrophysics Data System (ADS)

Gwóźdź-Lasoń, Monika

2017-10-01

The protection of the environment, including waste management, is one of the pillars of the policy of the Europe. The application which is presented in that paper tries to show a trans-disciplinary way to design geotechnical constructions - slope stability analysis. The generally accepted principles that the author presents are numerous modelling patterns of earth retaining walls as slope stabilization system. The paper constitutes an attempt to summarise and generalise earlier researches which involved FEM numeric procedures and the Z_Soil package. The design of anthropogenic soil used as a material for reinforced earth retaining walls, are not only of commercial but of environmental importance as well and consistent with the concept of sustainable development and the need to redevelop brownfield. This paper tries to show conceptual and empirical modelling approaches to slope stability system used in anthropogenic soil formation such as heaps, resulting from mining, with a special focus on urban areas of South of Poland and perspectives of anthropogenic materials application in geotechnical engineering are discussed.

Titanium Dioxide as a Catalyst Support in Heterogeneous Catalysis

PubMed Central

Bagheri, Samira; Muhd Julkapli, Nurhidayatullaili; Bee Abd Hamid, Sharifah

2014-01-01

The lack of stability is a challenge for most heterogeneous catalysts. During operations, the agglomeration of particles may block the active sites of the catalyst, which is believed to contribute to its instability. Recently, titanium oxide (TiO2) was introduced as an alternative support material for heterogeneous catalyst due to the effect of its high surface area stabilizing the catalysts in its mesoporous structure. TiO2 supported metal catalysts have attracted interest due to TiO2 nanoparticles high activity for various reduction and oxidation reactions at low pressures and temperatures. Furthermore, TiO2 was found to be a good metal oxide catalyst support due to the strong metal support interaction, chemical stability, and acid-base property. The aforementioned properties make heterogeneous TiO2 supported catalysts show a high potential in photocatalyst-related applications, electrodes for wet solar cells, synthesis of fine chemicals, and others. This review focuses on TiO2 as a support material for heterogeneous catalysts and its potential applications. PMID:25383380

Potential for use of environmental factors in urban planning

NASA Astrophysics Data System (ADS)

Teixeira da Silva, Ricardo; van der Ploeg, Martine; van Delden, Hedwig; Fleskens, Luuk

2016-04-01

Projections for population growth estimate, on top of the current 7.4 billion world population, an increase of 2 billion people for the next 40 years. It is also projected that 66 per cent of the world population in 2050 will live in urban areas. To accommodate the urban population growth cities are changing continuously land cover to urban areas. Such changes are a threat for natural resources and food production systems stability and capability to provide food and other functions. However, little has been done concerning a rational soil management for food production in urban and peri-urban areas. This study focuses on the assessment of soil lost due to urban expansion and discusses the potential loss regarding the quality of the soil for food production and environmental functions. It is relevant to increase the knowledge on the role of soils in peri-urban areas and in the interaction of physical, environmental and social factors. The methodology consists of assessing the soil quality in and around urban and peri-urban areas. It focuses particularly on the physical properties and the environmental factors, for two periods of time and account the potential losses due to urban expansion. This project is on-going, therefore current advances will be presented and will look for a discussion on the contribution of soil quality for decision-making and land management in urban and peri-urban areas.

The role of opacity and transparency in achieving strategic stability in South Asia.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rajain, Arpit; Ashraf, Tariq Mahmud

According to international relations theory, deterrence can be used as a tool to achieve stability between potentially hostile nations. India and Pakistan's long history of periodic crises raises the question of how they can achieve deterrence stability. 'Transparency' describes the flow of information between parties and plays a key role in establishing a deterrence relationship. This paper studies the balance needed between opacity and transparency in nuclear topics for the maintenance of deterrence stability between India and Pakistan. States with nuclear weapons are postulated to implement transparency in four categories: potential, capability, intent, and resolve. The study applies these categoriesmore » to the nuclear components of the ongoing India-Pakistan Composite Dialogue Working Group for Peace and Security including CBMs. To focus our efforts, we defined four scenarios to characterize representative strategic/military/political conditions. The scenarios are combinations of these two sets of opposite poles: competition - cooperation; extremism - moderation (to be understood primarily in a religious/nationalistic sense). We describe each scenario in terms of select focal areas (nuclear doctrine, nuclear command and control, nuclear stockpile, nuclear delivery/defensive systems, and conventional force posture). The scenarios help frame the realm of possibilities, and have been described in terms of expected conditions for the focal areas. We then use the conditions in each scenario to prescribe a range of information-sharing actions that the two countries could take to increase stability. We also highlight the information that should not be shared. These actions can be political (e.g., declarations), procedural (e.g., advance notice of certain military activities), or technologically based (e.g., seismic monitoring of the nuclear test moratorium).« less

Protein stability: a crystallographer’s perspective

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deller, Marc C., E-mail: mdeller@stanford.edu; Kong, Leopold; Rupp, Bernhard

An understanding of protein stability is essential for optimizing the expression, purification and crystallization of proteins. In this review, discussion will focus on factors affecting protein stability on a somewhat practical level, particularly from the view of a protein crystallographer. Protein stability is a topic of major interest for the biotechnology, pharmaceutical and food industries, in addition to being a daily consideration for academic researchers studying proteins. An understanding of protein stability is essential for optimizing the expression, purification, formulation, storage and structural studies of proteins. In this review, discussion will focus on factors affecting protein stability, on a somewhatmore » practical level, particularly from the view of a protein crystallographer. The differences between protein conformational stability and protein compositional stability will be discussed, along with a brief introduction to key methods useful for analyzing protein stability. Finally, tactics for addressing protein-stability issues during protein expression, purification and crystallization will be discussed.« less

The costs of housing developments on sites with elevated landslide risk in the UK

NASA Astrophysics Data System (ADS)

Barclay, K.; Heath, A.

2015-09-01

New housing targets are being set for local planning authorities resulting in more areas being zoned for development. There is currently no requirement for a landslide assessment prior to this zoning, and sites at elevated risk of landslides are being put forward for development without consideration of the additional costs and other impacts of building on these higher risk sites. This study aimed to reveal the increased financial, economic, social and environmental costs associated with these decisions. Case studies were focused on the city of Bath, an area of increasing population and “one of the most intensely landslipped areas in Britain’’. The case studies found the financial costs associated with building in a landslide risk area to be significantly higher than the equivalent construction in areas of greater geological stability. Furthermore, it was found that uncertainty in cost when developing in unstable areas exacerbates this problem as the final cost cannot be accurately predicted before construction.

Stable two-plane focusing for emittance-dominated sheet-beam transport

NASA Astrophysics Data System (ADS)

Carlsten, B. E.; Earley, L. M.; Krawczyk, F. L.; Russell, S. J.; Potter, J. M.; Ferguson, P.; Humphries, S.

2005-06-01

Two-plane focusing of sheet electron beams will be an essential technology for an emerging class of high-power, 100 to 300 GHz rf sources [Carlsten et al., IEEE Trans. Plasma Sci. 33, 85 (2005), ITPSBD, 0093-3813, 10.1109/TPS.2004.841172]. In these devices, the beam has a unique asymmetry in which the transport is emittance dominated in the sheet’s thin dimension and space-charge dominated in the sheet’s wide dimension. Previous work has studied the stability of the transport of beams in the emittance-dominated regime for both wiggler and periodic permanent magnet (PPM) configurations with single-plane focusing, and has found that bigger envelope scalloping occurs for equilibrium transport, as compared to space-charge dominated beams [Carlsten et al., this issue, Phys. Rev. ST Accel. Beams 8, 062001 (2005), PRABFM, 1098-4402]. In this paper, we describe the differences in transport stability when two-plane focusing is included. Two-plane wiggler focusing degrades the transport stability slightly, whereas two-plane PPM focusing greatly compromises the transport. On the other hand, single-plane PPM focusing can be augmented with external quadrupole fields to provide weak focusing in the sheet’s wide dimension, which has stability comparable to two-plane wiggler transport.

Post Modification of Metal-Organic Framework and Their Application In Cancer Theranostics

NASA Astrophysics Data System (ADS)

Lakkakula, Hima bindu

The research proposal aims to demonstrate that Metal-Organic Frameworks (MOFs) are mainly used for cancer theranostics which is the combination of both diagnostic and therapeutic functions. The research will emphasis on synthesis of Fe- MOFs by solvothermal nucleation, crystallization, characterization by microscopy and spectroscopy and evaluation with different lattice parameters and its morphology. Nowadays MOFs are used for the novel drug delivery purposes. The current published Fe- MOFs research focus is on the cancer theranostics by Indian medicines which will be impregnated into the MOFs and which will evaluate bioavailability and the chemotherapeutic activity of the drug. Nanotechnology provides the target specificity without affecting the healthy tissues. Other research problems to be addressed are the relationship between metal connectivity and ligand-based luminescence, MOF stability in an aqueous environment and activating it at increased temperature serves as a crucial role. The merits of this research are to increase the surface area and pore size of the drug so that the therapeutic efficacy can be improved. Moreover, the stabilization of metal-organic frameworks can also be enhanced with high surface area.

Resilience of Soil Microbial Communities to Metals and Additional Stressors: DNA-Based Approaches for Assessing “Stress-on-Stress” Responses

PubMed Central

Azarbad, Hamed; van Gestel, Cornelis A. M.; Niklińska, Maria; Laskowski, Ryszard; Röling, Wilfred F. M.; van Straalen, Nico M.

2016-01-01

Many microbial ecology studies have demonstrated profound changes in community composition caused by environmental pollution, as well as adaptation processes allowing survival of microbes in polluted ecosystems. Soil microbial communities in polluted areas with a long-term history of contamination have been shown to maintain their function by developing metal-tolerance mechanisms. In the present work, we review recent experiments, with specific emphasis on studies that have been conducted in polluted areas with a long-term history of contamination that also applied DNA-based approaches. We evaluate how the “costs” of adaptation to metals affect the responses of metal-tolerant communities to other stress factors (“stress-on-stress”). We discuss recent studies on the stability of microbial communities, in terms of resistance and resilience to additional stressors, focusing on metal pollution as the initial stress, and discuss possible factors influencing the functional and structural stability of microbial communities towards secondary stressors. There is increasing evidence that the history of environmental conditions and disturbance regimes play central roles in responses of microbial communities towards secondary stressors. PMID:27314330

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rosales, Bryan A.; Hanrahan, Michael P.; Boote, Brett W.

Hybrid lead perovskites containing a mixture of organic and inorganic cations and anions have lead to solar cell devices with better performance and stability than their single halide analogs. Here, 207Pb solid-state nuclear magnetic resonance and single particle photoluminescence spectroscopies show that the structure and composition of mixed-halide and—likely—other hybrid lead perovskites is much more complex than previously thought and is highly dependent on their synthesis. While a majority of reports in the area focus on the construction of photovoltaic devices, this perspective focuses instead on achieving a better understanding of the fundamental chemistry and photophysics of these materials, asmore » this will aid not only in constructing improved devices, but also in generating new uses for these unique materials.« less

The thermal stability and catalytic application of manganese oxide-zirconium oxide powders

NASA Astrophysics Data System (ADS)

Zhao, Qiang

MnOx-ZrO2 mixed oxide is an active catalyst for combustion, oxidation, and oxygen storage applications. MnOx-ZrO 2 mixture also has large reversible adsorption capability for NO x, which makes it a promising candidate for NOx abatement in automobile emission control. However, MnOx-ZrO 2 mixed oxide has not been used extensively because the processing and the thermal stability of resulting powders have not been studied systematically. It is critical to have thermally stable catalytic material because the application temperature can reach as high as 1000°C during service. In this study, we focused on improving the thermal stability of oxide powders, such as MnO x, ZrO2, and MnOx-ZrO2, by controlling the processing methods and parameters. For pure MnOx made from the precipitation method using Mn(NO3)2 aqueous solution and ammonium hydroxide, we found that lower concentration of Mn(NO3) 2 solution and larger amount of ammonium hydroxide resulted in higher surface area powders. For pure ZrO2, we found curing hydrous zirconia in the mother liquid produced ZrO2 powders with larger pore volume and pore size. The specific surface area was also significantly enhanced by curing for the synthesized powders before calcination or after low temperature calcinations, and this improvement could be preserved to high temperatures if SiO2 was doped in ZrO2. A Monte Carlo simulation model examining the effect of primary particle packing on the specific surface area was used to explain the curing result. MnOx-ZrO2 mixtures had higher surface area than the single component oxide at 500 and 700°C because composite powders sintered less. The sintering behavior of composite powders at 900°C was opposite to that at 500°C and the specific surface area of MnOx-ZrO2 decreased drastically at 900°C. Curing ZrO2 first or using La dopant could significantly enhance the specific surface area of MnOx-ZrO2 at 900°C. Through the tests of the redox property and NO storage capability we found a close relationship between the enhanced thermal stability and better catalytic performance.

Issues of Stability and Change in Interest Development

ERIC Educational Resources Information Center

Tracey, Terence J. G.; Sodano, Sandro M.

2008-01-01

Interest development is not an easily studied process. There are at least 4 methods for examining the process of stability and change over time: relative stability, absolute stability, profile stability, and structural stability. A program of research that focuses on examining these 4 types of stability is summarized relative to the issues…

Some Thoughts on Stability in Nonlinear Periodic Focusing Systems [Addendum

DOE R&D Accomplishments Database

McMillan, Edwin M.

1968-03-29

Addendum to September 5, 1967 report with the same title and with the abstract: A brief discussion is given of the long-term stability of particle motions through periodic focusing structures containing lumped nonlinear elements. A method is presented whereby one can specify the nonlinear elements in such a way as to generate a variety of structures in which the motion has long-term stability.

Habitat stability and occurrences of malaria vector larvae in western Kenya highlands.

PubMed

Himeidan, Yousif E; Zhou, Guofa; Yakob, Laith; Afrane, Yaw; Munga, Stephen; Atieli, Harrysone; El-Rayah, El-Amin; Githeko, Andrew K; Yan, Guiyun

2009-10-21

Although the occurrence of malaria vector larvae in the valleys of western Kenya highlands is well documented, knowledge of larval habitats in the uphill sites is lacking. Given that most inhabitants of the highlands actually dwell in the uphill regions, it is important to develop understanding of mosquito breeding habitat stability in these sites in order to determine their potential for larval control. A total of 128 potential larval habitats were identified in hilltops and along the seasonal streams in the Sigalagala area of Kakamega district, western Kenya. Water availability in the habitats was followed up daily from August 3, 2006 to February 23, 2007. A habitat is defined as stable when it remains aquatic continuously for at least 12 d. Mosquito larvae were observed weekly. Frequencies of aquatic, stable and larvae positive habitats were compared between the hilltop and seasonal stream area using chi2-test. Factors affecting the presence/absence of Anopheles gambiae larvae in the highlands were determined using multiple logistic regression analysis. Topography significantly affected habitat availability and stability. The occurrence of aquatic habitats in the hilltop was more sporadic than in the stream area. The percentage of habitat occurrences that were classified as stable during the rainy season is 48.76% and 80.79% respectively for the hilltop and stream area. Corresponding frequencies of larvae positive habitats were 0% in the hilltop and 5.91% in the stream area. After the rainy season, only 23.42% of habitat occurrences were stable and 0.01% larvae positive habitats were found in the hilltops, whereas 89.75% of occurrences remained stable in the stream area resulting in a frequency of 12.21% larvae positive habitats. The logistic regression analysis confirmed the association between habitat stability and larval occurrence and indicated that habitat surface area was negatively affecting the occurrence of An. gambiae larvae. While An. gambiae and An. funestus larvae occurred throughout the study period along the streams, a total of only 15 An. gambiae larvae were counted in the hilltops, and no An. funestus were found. Moreover, no larvae managed to develop into adults in the hilltops, and the density of adult An. gambiae was consistently low, averaging at 0.06 females per house per survey. The occurrence of malaria vector larvae in the hilltop area was uncommon as a result of the low availability and high instability of habitats. To optimize the cost-effectiveness of malaria interventions in the western Kenya highlands, larval control should be focused primarily along the streams, as these are likely the only productive habitats at high altitude.

Could refuge theory and rivers acting as barriers explain the genetic variability distribution in the Atlantic Forest?

PubMed

Cazé, Ana Luiza R; Mäder, Geraldo; Nunes, Teonildes S; Queiroz, Luciano P; de Oliveira, Guilherme; Diniz-Filho, José Alexandre F; Bonatto, Sandro L; Freitas, Loreta B

2016-08-01

The Atlantic Forest is one of the most species-rich ecoregions in the world. The historical origins of this richness and the evolutionary processes that produced diversification and promoted speciation in this ecosystem remain poorly understood. In this context, focusing on Passiflora contracta, an endemic species from the Atlantic Forest distributed exclusively at sea level along forest edges, this study aimed to characterize the patterns of genetic variability and explore two hypotheses that attempt to explain the possible causes of the genetic diversity in this region: the refuge and riverine barrier theories. We employed Bayesian methods combined with niche modeling to identify genetically homogeneous groups, to determine the diversification age, and identify long-term climate stability areas to species survival. The analyses were performed using molecular markers from nuclear and plastid genomes, with samples collected throughout the entire geographic distribution of the species, and comparisons with congeners species. The results indicated that populations were genetically structured and provided evidence of demographic stability. The molecular markers indicated the existence of a clear structure and the presence of five homogeneous groups. Interestingly, the separation of the groups coincides with the geographical locations of local rivers, corroborating the hypothesis of rivers acting as barriers to gene flow in this species. The highest levels of genetic diversity and the areas identified as having long-term climate stability were found in the same region reported for other species as a possible refuge area during the climatic changes of the Quaternary. Copyright © 2016 Elsevier Inc. All rights reserved.

Present understanding of the stability of Li-stuffed garnets with moisture, carbon dioxide, and metallic lithium

NASA Astrophysics Data System (ADS)

Hofstetter, Kyle; Samson, Alfred Junio; Narayanan, Sumaletha; Thangadurai, Venkataraman

2018-06-01

Fast lithium-ion conducting garnet-type metal oxides are promising membranes for next-generation all-solid-state Li batteries and beyond Li-ion batteries, including Li-air and Li-S batteries, due to their high total Li-ion conductivity and excellent chemical stability against reaction with elemental Li. Several studies have been reported on structure-chemical composition-ionic conductivity property in Li-stuffed garnet-type metal oxides. Here, an overview of the chemical and electrochemical stability of lithium-based garnets against moisture/humidity, aqueous solutions, carbon dioxide, sulfur, and metallic lithium are analyzed. Moisture and aqueous stability studies focus on understanding the crystal structure stability, the proton exchange capacity as a function of Li content in Li-stuffed garnets, and how the protonated species affect the crystal structure and mass transport properties. H+/Li+ exchange was found to be in the range of 2-100%. Stability concerning Li-ion conductivity and morphology under carbon dioxide are discussed. Interfacial chemical stability with lithium metal characterized by electrochemical stability window, Li dendrite formation and area specific resistance (ASR) for the reaction Li ⇌ Li+ +e- are presented. Recent attempts to suppress dendrite formation and to reduce ASR via surface modification are also highlighted. Li and Li-stuffed garnet interface ASR values are shown to be as high as >2000 Ω cm2 and as low as 1 Ω cm2 at room temperature for surface modified Li-stuffed samples. Furthermore, recent studies on Li-S battery utilizing chemically stable Li - garnet electrolyte are also discussed.

Analysis by the Residual Method for Estimate Market Value of Land on the Areas with Mining Exploitation in Subsoil under Future New Building

NASA Astrophysics Data System (ADS)

Gwozdz-Lason, Monika

2017-12-01

This paper attempts to answer some of the following questions: what is the main selling advantage of a plot of land on the areas with mining exploitation? which attributes influence on market value the most? and how calculate the mining influence in subsoil under future new building as market value of plot with commercial use? This focus is not accidental, as the paper sets out to prove that the subsoil load bearing capacity, as directly inferred from the local geotechnical properties with mining exploitation, considerably influences the market value of this type of real estate. Presented in this elaborate analysis and calculations, are part of the ongoing development works which aimed at suggesting a new technology and procedures for estimating the value of the land belonging to the third category geotechnical. Analysed the question was examined both in terms of the theoretical and empirical. On the basis of the analysed code calculations in residual method, numerical, statistical and econometric defined results and final conclusions. A market analysis yielded a group of subsoil stabilization costs which depend on the mining operations interaction, subsoil parameters, type of the contemplated structure, its foundations, selected stabilization method, its overall area and shape.

The impact of housing rehabilitation on local neighborhoods: the case of small community development organizations.

PubMed

Smith, Marvin M; Hevener, Christy Chung

2011-01-01

Across the nation, nonprofit organizations located in poor and declining neighborhoods are promoting homeownership in the hopes that their efforts will stave off decline and contribute to neighborhood stability. A common homeownership strategy among nonprofits is to acquire boarded-up or deteriorated homes at a low price, rehabilitate them, and then sell them at an affordable price. As these programs continue, nonprofit organizations want to show quantitatively that neighborhood revitalization works—that the funds devoted to an area stabilize neighborhoods or, even more, that they initiate a surge of continued upward progress. But, unlike their larger counterparts, smaller community development organizations are usually at a disadvantage in undertaking such an evaluation. This study will help illustrate what might be done. It focuses on the case of St. Joseph's Carpenter Society (SJCS) in Camden, New Jersey and assesses the quantitative impact that SJCS has on its target neighborhoods. A three-tiered approach is adopted that ranges from a target and comparison area analysis, to regression analysis of SJCS's impact on local housing prices, and finally to an examination of the relative market performance of SJCS's houses. All told, the analysis suggests that SJCS's rehabilitation and homeownership education activities appear to have a positive influence on the neighborhoods in its target area.

The combination of electrospray and flow focusing

NASA Astrophysics Data System (ADS)

Gañán-Calvo, Alfonso M.; López-Herrera, José M.; Riesco-Chueca, Pascual

2006-11-01

An ultra-fine liquid atomization procedure combining the advantages of electrospray and flow focusing is presented. Both techniques are known to produce strikingly small and steady liquid micro-jets issuing from menisci held by capillary forces. Such menisci take the form of a cusp-like drop attached to the feeding tube (flow focusing: FF) or a Taylor cone (electrospray: ES). The issuing micro-jets are forced or ‘sucked’ from the parent meniscus either by pressure or electrohydrodynamic forces. Subsequent capillary breakup of the jet leads to fine sprays of remarkable quality. Here we describe the joint effect of pressurization and electrification in a flow focusing device, and the subsequent coupling of both ES and FF phenomena. For any given liquid and flow rate, the combined procedure gives rise to significantly smaller droplet sizes than observed in any of the source techniques. The co-flowing gas stream removes space charges; in addition, the perforated plate facing the feed tube provides an electric barrier, shielding the jet-meniscus or ‘production’ area from the spray or ‘product’ area. As a result, space charges and electrified droplets are removed from the production area, thus avoiding the ambient electric saturation which becomes a limiting factor in ES-spraying: a significantly enhanced spraying stability ensues, with a much wider operation range than FF or ES. Other unexpected outcomes from the combination are also shown. A theoretical model is developed to predict the emitted droplet size: a first integral of the momentum equation yielding a generalized Bernoulli equation, and an explicit approximation for the jet diameter and droplet size, accurate within a broad parametrical band.

Measurements of Mercury Released from Solidified/Stabilized Waste Forms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mattus, C.H.

2001-04-19

This report covers work performed during FY 1999-2000 in support of treatment demonstrations conducted for the Mercury Working Group of the U.S. Department of Energy (DOE) Mixed Waste Focus Area. In order to comply with the requirements of the Resource Conservation and Recovery Act, as implemented by the U.S. Environmental Protection Agency (EPA), DOE must use one of these procedures for wastes containing mercury at levels above 260 ppm: a retorting/roasting treatment or an incineration treatment (if the wastes also contain organics). The recovered radioactively contaminated mercury must then be treated by an amalgamation process prior to disposal. The DOEmore » Mixed Waste Focus Area and Mercury Working Group are working with the EPA to determine if some alternative processes could treat these types of waste directly, thereby avoiding for DOE the costly recovery step. They sponsored a demonstration in which commercial vendors applied their technologies for the treatment of two contaminated waste soils from Brookhaven National Laboratory. Each soil was contaminated with {approx}4500 ppm mercury; however, one soil had as a major radioelement americium-241, while the other contained mostly europium-152. The project described in this report addressed the need for data on the mercury vapor released by the solidified/stabilized mixed low-level mercury wastes generated during these demonstrations as well as the comparison between the untreated and treated soils. A related work began in FY 1998, with the measurement of the mercury released by amalgamated mercury, and the results were reported in ORNL/TM-13728. Four treatments were performed on these soils. The baseline was obtained by thermal treatment performed by SepraDyne Corp., and three forms of solidification/stabilization were employed: one using sulfur polymer cement (Brookhaven National Laboratory), one using portland cement [Allied Technology Group (ATG)], and a third using proprietary additives (Nuclear Fuel Services).« less

Development of processing techniques for advanced thermal protection materials

NASA Technical Reports Server (NTRS)

Selvaduray, Guna S.

1995-01-01

The main purpose of this work has been in the development and characterization of materials for high temperature applications. Thermal Protection Systems (TPS) are constantly being tested, and evaluated for increased thermal shock resistance, high temperature dimensional stability, and tolerance to environmental effects. Materials development was carried out through the use of many different instruments and methods, ranging from extensive elemental analysis to physical attributes testing. The six main focus areas include: (1) protective coatings for carbon/carbon composites; (2) TPS material characterization; (3) improved waterproofing for TPS; (4) modified ceramic insulation for bone implants; (5) improved durability ceramic insulation blankets; and (6) ultra-high temperature ceramics. This report describes the progress made in these research areas during this contract period.

Dynamics of aerospace vehicles

NASA Technical Reports Server (NTRS)

Schmidt, David K.

1991-01-01

The focus of this research was to address the modeling, including model reduction, of flexible aerospace vehicles, with special emphasis on models used in dynamic analysis and/or guidance and control system design. In the modeling, it is critical that the key aspects of the system being modeled be captured in the model. In this work, therefore, aspects of the vehicle dynamics critical to control design were important. In this regard, fundamental contributions were made in the areas of stability robustness analysis techniques, model reduction techniques, and literal approximations for key dynamic characteristics of flexible vehicles. All these areas are related. In the development of a model, approximations are always involved, so control systems designed using these models must be robust against uncertainties in these models.

Regularized magnetotelluric inversion based on a minimum support gradient stabilizing functional

NASA Astrophysics Data System (ADS)

Xiang, Yang; Yu, Peng; Zhang, Luolei; Feng, Shaokong; Utada, Hisashi

2017-11-01

Regularization is used to solve the ill-posed problem of magnetotelluric inversion usually by adding a stabilizing functional to the objective functional that allows us to obtain a stable solution. Among a number of possible stabilizing functionals, smoothing constraints are most commonly used, which produce spatially smooth inversion results. However, in some cases, the focused imaging of a sharp electrical boundary is necessary. Although past works have proposed functionals that may be suitable for the imaging of a sharp boundary, such as minimum support and minimum gradient support (MGS) functionals, they involve some difficulties and limitations in practice. In this paper, we propose a minimum support gradient (MSG) stabilizing functional as another possible choice of focusing stabilizer. In this approach, we calculate the gradient of the model stabilizing functional of the minimum support, which affects both the stability and the sharp boundary focus of the inversion. We then apply the discrete weighted matrix form of each stabilizing functional to build a unified form of the objective functional, allowing us to perform a regularized inversion with variety of stabilizing functionals in the same framework. By comparing the one-dimensional and two-dimensional synthetic inversion results obtained using the MSG stabilizing functional and those obtained using other stabilizing functionals, we demonstrate that the MSG results are not only capable of clearly imaging a sharp geoelectrical interface but also quite stable and robust. Overall good performance in terms of both data fitting and model recovery suggests that this stabilizing functional is effective and useful in practical applications.[Figure not available: see fulltext.

The design of delay-dependent wide-area DOFC with prescribed degree of stability α for damping inter-area low-frequency oscillations in power system.

PubMed

Sun, Miaoping; Nian, Xiaohong; Dai, Liqiong; Guo, Hua

2017-05-01

In this paper, the delay-dependent wide-area dynamic output feedback controller (DOFC) with prescribed degree of stability is proposed for interconnected power system to damp inter-area low-frequency oscillations. Here, the prescribed degree of stability α is used to maintain all the poles on the left of s=-α in the s-plane. Firstly, residue approach is adopted to select input-output control signals and the schur balanced truncation model reduction method is utilized to obtain the reduced power system model. Secondly, based on Lyapunov stability theory and transformation operation in complex plane, the sufficient condition of asymptotic stability for closed-loop power system with prescribed degree of stability α is derived. Then, a novel method based on linear matrix inequalities (LMIs) is presented to obtain the parameters of DOFC and calculate delay margin of the closed-loop system considering the prescribed degree of stability α. Finally, case studies are carried out on the two-area four-machine system, which is controlled by classical wide-area power system stabilizer (WAPSS) in reported reference and our proposed DOFC respectively. The effectiveness and advantages of the proposed method are verified by the simulation results under different operating conditions. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

Lead Halide Perovskites: Challenges and Opportunities in Advanced Synthesis and Spectroscopy

DOE PAGES

Rosales, Bryan A.; Hanrahan, Michael P.; Boote, Brett W.; ...

2017-03-28

Hybrid lead perovskites containing a mixture of organic and inorganic cations and anions have lead to solar cell devices with better performance and stability than their single halide analogs. Here, 207Pb solid-state nuclear magnetic resonance and single particle photoluminescence spectroscopies show that the structure and composition of mixed-halide and—likely—other hybrid lead perovskites is much more complex than previously thought and is highly dependent on their synthesis. While a majority of reports in the area focus on the construction of photovoltaic devices, this perspective focuses instead on achieving a better understanding of the fundamental chemistry and photophysics of these materials, asmore » this will aid not only in constructing improved devices, but also in generating new uses for these unique materials.« less

Texas lignite mining: Groundwater and slope stability control in the nineties and beyond

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lawrence J.

As lignite mining in Texas approaches and exceeds depths of 200 feet below ground level, rising costs demand that innovative mining approaches be used in order to maintain the economic viability of lignite mining. Groundwater and slope stability problems multiply at these depths, resulting in increasing focus on how to control these costs. Dewatering costs are consistently rising for the lignite industry, as deeper mining encounters more and larger saturated sand bodies. These sands require dewatering in order to improve slope stability. Planning and analysis become more important as the number of wells grows beyond what can be managed withmore » a simple {open_quotes}cookie-cutter{close_quotes} approach. Slope stability plays an increasing role in mining concerns as deeper lignite is recovered. Slope stability causes several problems, including loss of lignite, increased rehandle, and hazards to personnel and equipment. Traditional lignite mine planning involved a fairly {open_quotes}generic{close_quotes} pit design with one design highwall angle, one design spoil angle, and little geotechnical evaluation of the deposit. This {open_quotes}one mine-one design{close_quotes} approach, while cost-effective in the past, is now being replaced by a more critical analysis of the design requirements of each area. Geotechnical evaluation plays an increasing role in the planning and operational aspects of lignite mining. Laboratory core sample test results can be used for slope stability modeling, in order to obtain more accurate design and operational information.« less

Direct frequency comb optical frequency standard based on two-photon transitions of thermal atoms

PubMed Central

Zhang, S. Y.; Wu, J. T.; Zhang, Y. L.; Leng, J. X.; Yang, W. P.; Zhang, Z. G.; Zhao, J. Y.

2015-01-01

Optical clocks have been the focus of science and technology research areas due to their capability to provide highest frequency accuracy and stability to date. Their superior frequency performance promises significant advances in the fields of fundamental research as well as practical applications including satellite-based navigation and ranging. In traditional optical clocks, ultrastable optical cavities, laser cooling and particle (atoms or a single ion) trapping techniques are employed to guarantee high stability and accuracy. However, on the other hand, they make optical clocks an entire optical tableful of equipment, and cannot work continuously for a long time; as a result, they restrict optical clocks used as very convenient and compact time-keeping clocks. In this article, we proposed, and experimentally demonstrated, a novel scheme of optical frequency standard based on comb-directly-excited atomic two-photon transitions. By taking advantage of the natural properties of the comb and two-photon transitions, this frequency standard achieves a simplified structure, high robustness as well as decent frequency stability, which promise widespread applications in various scenarios. PMID:26459877

Monodispersed silk fibroin microdroplets for protein stabilization

NASA Astrophysics Data System (ADS)

Liu, Qiang; Jiang, Nan; Liu, Dewen; Ying, Guoliang; Shi, Qiusheng; Yetisen, Ali K.; Liu, Haifeng; Fan, Yubo

2018-04-01

Low stability of globular protein droplets in emulsion significantly limits their applications in drug encapsulation, long-term storage, and controlled drug release. Here, a microfluidic flow-focusing device was utilized to synthesize horseradish peroxidase (HRP)-loaded silk fibroin microdroplets. The two immiscible streams of microfluidic flow-focusing were regenerated by silk fibroin solution and a mixture of 95 wt. % sunflower oil and 5 wt. % span 80 as the dispersed and continuous phases, respectively. In this study, the water-in-oil silk fibroin microdroplets were homogeneously produced by leveraging the discrete and periodic breakup of microdroplets and regulating the flow rates. Moreover, the result showed that the stability of encapsulated HRP in microdroplets was 25% higher than that of HRP after 6 weeks incubation. Thus, the microfluidic flow-focusing is a promising technique to form monodisperse microdroplets and maximize the stability of protein droplets.

Clearwater Focus Watershed; Nez Perce Tribe, 2003-2004 Annual Report.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jones, Ira

2004-06-01

The Nez Perce Tribe Department of Fisheries Resource Management, Watershed Division, approaches watershed restoration with a goal to protect, restore, and enhance a connected network of functioning habitat types capable of supporting all fish life stages. Its goal is also to re-establish normal patterns of production, dispersal, and exchange of genetic information within the 1855 Treaty Area. The Nez Perce Tribe began watershed restoration projects within the Clearwater River Subbasin in 1996. Progress has been made in restoring the sub-basin by excluding cattle from critical riparian areas through fencing, stabilizing stream banks, decommissioning roads, and upgrading culverts. Coordination of thesemore » projects is critical to the success of the restoration of the sub-basin. Coordination activities also includes: inter and intra-department coordination, sub-basin assessment and planning, involving government and private organizations, and treaty area coordination.« less

Spinel Co3O4 nanomaterials for efficient and stable large area carbon-based printed perovskite solar cells.

PubMed

Bashir, Amna; Shukla, Sudhanshu; Lew, Jia Haur; Shukla, Shashwat; Bruno, Annalisa; Gupta, Disha; Baikie, Tom; Patidar, Rahul; Akhter, Zareen; Priyadarshi, Anish; Mathews, Nripan; Mhaisalkar, Subodh G

2018-02-01

Carbon based perovskite solar cells (PSCs) are fabricated through easily scalable screen printing techniques, using abundant and cheap carbon to replace the hole transport material (HTM) and the gold electrode further reduces costs, and carbon acts as a moisture repellent that helps in maintaining the stability of the underlying perovskite active layer. An inorganic interlayer of spinel cobaltite oxides (Co 3 O 4 ) can greatly enhance the carbon based PSC performance by suppressing charge recombination and extracting holes efficiently. The main focus of this research work is to investigate the effectiveness of Co 3 O 4 spinel oxide as the hole transporting interlayer for carbon based perovskite solar cells (PSCs). In these types of PSCs, the power conversion efficiency (PCE) is restricted by the charge carrier transport and recombination processes at the carbon-perovskite interface. The spinel Co 3 O 4 nanoparticles are synthesized using the chemical precipitation method, and characterized by X-ray diffraction (XRD), X-ray absorption spectroscopy (XAS), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM) and UV-Vis spectroscopy. A screen printed thin layer of p-type inorganic spinel Co 3 O 4 in carbon PSCs provides a better-energy level matching, superior efficiency, and stability. Compared to standard carbon PSCs (PCE of 11.25%) an improved PCE of 13.27% with long-term stability, up to 2500 hours under ambient conditions, is achieved. Finally, the fabrication of a monolithic perovskite module is demonstrated, having an active area of 70 cm 2 and showing a power conversion efficiency of >11% with virtually no hysteresis. This indicates that Co 3 O 4 is a promising interlayer for efficient and stable large area carbon PSCs.

Scalable fabrication of perovskite solar cells

DOE PAGES

Li, Zhen; Klein, Talysa R.; Kim, Dong Hoe; ...

2018-03-27

Perovskite materials use earth-abundant elements, have low formation energies for deposition and are compatible with roll-to-roll and other high-volume manufacturing techniques. These features make perovskite solar cells (PSCs) suitable for terawatt-scale energy production with low production costs and low capital expenditure. Demonstrations of performance comparable to that of other thin-film photovoltaics (PVs) and improvements in laboratory-scale cell stability have recently made scale up of this PV technology an intense area of research focus. Here, we review recent progress and challenges in scaling up PSCs and related efforts to enable the terawatt-scale manufacturing and deployment of this PV technology. We discussmore » common device and module architectures, scalable deposition methods and progress in the scalable deposition of perovskite and charge-transport layers. We also provide an overview of device and module stability, module-level characterization techniques and techno-economic analyses of perovskite PV modules.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Zhen; Klein, Talysa R.; Kim, Dong Hoe

Perovskite materials use earth-abundant elements, have low formation energies for deposition and are compatible with roll-to-roll and other high-volume manufacturing techniques. These features make perovskite solar cells (PSCs) suitable for terawatt-scale energy production with low production costs and low capital expenditure. Demonstrations of performance comparable to that of other thin-film photovoltaics (PVs) and improvements in laboratory-scale cell stability have recently made scale up of this PV technology an intense area of research focus. Here, we review recent progress and challenges in scaling up PSCs and related efforts to enable the terawatt-scale manufacturing and deployment of this PV technology. We discussmore » common device and module architectures, scalable deposition methods and progress in the scalable deposition of perovskite and charge-transport layers. We also provide an overview of device and module stability, module-level characterization techniques and techno-economic analyses of perovskite PV modules.« less

The history and future trends of ocean warming-induced gas hydrate dissociation in the SW Barents Sea

NASA Astrophysics Data System (ADS)

Vadakkepuliyambatta, Sunil; Chand, Shyam; Bünz, Stefan

2017-01-01

The Barents Sea is a major part of the Arctic where the Gulf Stream mixes with the cold Arctic waters. Late Cenozoic uplift and glacial erosion have resulted in hydrocarbon leakage from reservoirs, evolution of fluid flow systems, shallow gas accumulations, and hydrate formation throughout the Barents Sea. Here we integrate seismic data observations of gas hydrate accumulations along with gas hydrate stability modeling to analyze the impact of warming ocean waters in the recent past and future (1960-2060). Seismic observations of bottom-simulating reflectors (BSRs) indicate significant thermogenic gas input into the hydrate stability zone throughout the SW Barents Sea. The distribution of BSR is controlled primarily by fluid flow focusing features, such as gas chimneys and faults. Warming ocean bottom temperatures over the recent past and in future (1960-2060) can result in hydrate dissociation over an area covering 0.03-38% of the SW Barents Sea.

A 2,000-year reconstruction of the rain-fed maize agricultural niche in the US Southwest.

PubMed

Bocinsky, R Kyle; Kohler, Timothy A

2014-12-04

Humans experience, adapt to and influence climate at local scales. Paleoclimate research, however, tends to focus on continental, hemispheric or global scales, making it difficult for archaeologists and paleoecologists to study local effects. Here we introduce a method for high-frequency, local climate-field reconstruction from tree-rings. We reconstruct the rain-fed maize agricultural niche in two regions of the southwestern United States with dense populations of prehispanic farmers. Niche size and stability are highly variable within and between the regions. Prehispanic rain-fed maize farmers tended to live in agricultural refugia--areas most reliably in the niche. The timing and trajectory of the famous thirteenth century Pueblo migration can be understood in terms of relative niche size and stability. Local reconstructions like these illuminate the spectrum of strategies past humans used to adapt to climate change by recasting climate into the distributions of resources on which they depended.

Perspectives on the geographic stability and mobility of people in cities

PubMed Central

Hanson, Susan

2005-01-01

A class of questions in the human environment sciences focuses on the relationship between individual or household behavior and local geographic context. Central to these questions is the nature of people's geographic mobility as well as the duration of their locational stability at varying spatial and temporal scales. The problem for researchers is that the processes of mobility/stability are temporally and spatially dynamic and therefore difficult to measure. Whereas time and space are continuous, analysts must select levels of aggregation for both length of time in place and spatial scale of place that fit with the problem in question. Previous work has emphasized mobility and suppressed stability as an analytic category. I focus here on stability and show how analyzing individuals' stability requires also analyzing their mobility. Through an empirical example centered on the relationship between entrepreneurship and place, I demonstrate how a spotlight on stability illuminates a resolution to the measurement problem by highlighting the interdependence between the time and space dimensions of stability/mobility. PMID:16230616

Vegetation Cover Analysis in Shaanxi Province of China Based on Grid Pixel Ternd Analysis and Stability Evaluation

NASA Astrophysics Data System (ADS)

Yue, H.; Liu, Y.

2018-04-01

As a key factor affecting the biogeochemical cycle of human existence, terrestrial vegetation is vulnerable to natural environment and human activities, with obvious temporal and spatial characteristics. The change of vegetation cover will affect the ecological balance and environmental quality to a great extent. Therefore, the research on the causes and influencing factors of vegetation cover has become the focus of attention of scholars at home and abroad. In the evolution of human activities and natural environment, the vegetation coverage in Shaanxi has changed accordingly. Using MODIS/NDVI 2000-2014 time series data, using the method of raster pixel trend analysis, stability evaluation, rescaled range analysis and correlation analysis, the climatic factors in Shaanxi province were studied in the near 15 years vegetation spatial and temporal variation and influence of vegetation NDVI changes. The results show that NDVI in Shaanxi province in the near 15 years increased by 0.081, the increase of NDVI in Northern Shaanxi was obvious, and negative growth was found in some areas of Guanzhong, southern Shaanxi NDVI overall still maintained at a high level; the trend of vegetation change in Shaanxi province has obvious spatial differences, most of the province is a slight tendency to improve vegetation, there are many obvious improvement areas in Northern Shaanxi Province. Guanzhong area vegetation area decreased, the small range of variation of vegetation in Shaanxi province; the most stable areas are mainly concentrated in the southern, southern Yanan, Yulin, Xi'an area of Weinan changed greatly; Shaanxi Province in recent 15 a, the temperature and precipitation have shown an increasing trend, and the vegetation NDVI is more closely related to the average annual rainfall, with increase of 0.48 °C/10 years and 69.5 mm per year.

Graphene–Gold Nanoparticles Hybrid—Synthesis, Functionalization, and Application in a Electrochemical and Surface-Enhanced Raman Scattering Biosensor

PubMed Central

Khalil, Ibrahim; Julkapli, Nurhidayatullaili Muhd; Yehye, Wageeh A.; Basirun, Wan Jefrey; Bhargava, Suresh K.

2016-01-01

Graphene is a single-atom-thick two-dimensional carbon nanosheet with outstanding chemical, electrical, material, optical, and physical properties due to its large surface area, high electron mobility, thermal conductivity, and stability. These extraordinary features of graphene make it a key component for different applications in the biosensing and imaging arena. However, the use of graphene alone is correlated with certain limitations, such as irreversible self-agglomerations, less colloidal stability, poor reliability/repeatability, and non-specificity. The addition of gold nanostructures (AuNS) with graphene produces the graphene–AuNS hybrid nanocomposite which minimizes the limitations as well as providing additional synergistic properties, that is, higher effective surface area, catalytic activity, electrical conductivity, water solubility, and biocompatibility. This review focuses on the fundamental features of graphene, the multidimensional synthesis, and multipurpose applications of graphene–Au nanocomposites. The paper highlights the graphene–gold nanoparticle (AuNP) as the platform substrate for the fabrication of electrochemical and surface-enhanced Raman scattering (SERS)-based biosensors in diverse applications as well as SERS-directed bio-imaging, which is considered as an emerging sector for monitoring stem cell differentiation, and detection and treatment of cancer. PMID:28773528

Transition from Ignition to Flame Growth under External Radiation in Three Dimensions (TIGER-3D)

NASA Technical Reports Server (NTRS)

Kashiwagi, Takashi; Nakamura, Yuji; Olson, Sandra L.; Mell, William

2004-01-01

This study focuses on localized ignition by external radiant flux and subsequent flame growth over thin polymeric materials (plastic and paper) in microgravity. Two transition stages were observed. The first transition stage covers the period from the onset of ignition to the formation of stabilized flame near the ignited area. This is followed by the second transition of the flame growth stage from the initial stabilized flame to sustained fire growth away from the ignited area. For the first stage, ignition experiments of thin PMMA sheets were conducted using a CO2 laser as an external source in the 10 s drop tower. The results of front side surface ignition and of backside surface ignition were observed. The effects of imposed flow velocity, sample thickness, and ambient oxygen concentration on ignition are obtained. Numerical study was conducted to investigate to understand and predict ignition behavior observed in the experiments. For the second stage, numerical study is being conducted to describe the effects of gravity on heat release rate of a PMMA sheet. The gravity level was varied from zero to normal gravity. The preliminary results show that the maximum heat release occurs at around 0.02 g.

Graphene-Gold Nanoparticles Hybrid-Synthesis, Functionalization, and Application in a Electrochemical and Surface-Enhanced Raman Scattering Biosensor.

PubMed

Khalil, Ibrahim; Julkapli, Nurhidayatullaili Muhd; Yehye, Wageeh A; Basirun, Wan Jefrey; Bhargava, Suresh K

2016-05-24

Graphene is a single-atom-thick two-dimensional carbon nanosheet with outstanding chemical, electrical, material, optical, and physical properties due to its large surface area, high electron mobility, thermal conductivity, and stability. These extraordinary features of graphene make it a key component for different applications in the biosensing and imaging arena. However, the use of graphene alone is correlated with certain limitations, such as irreversible self-agglomerations, less colloidal stability, poor reliability/repeatability, and non-specificity. The addition of gold nanostructures (AuNS) with graphene produces the graphene-AuNS hybrid nanocomposite which minimizes the limitations as well as providing additional synergistic properties, that is, higher effective surface area, catalytic activity, electrical conductivity, water solubility, and biocompatibility. This review focuses on the fundamental features of graphene, the multidimensional synthesis, and multipurpose applications of graphene-Au nanocomposites. The paper highlights the graphene-gold nanoparticle (AuNP) as the platform substrate for the fabrication of electrochemical and surface-enhanced Raman scattering (SERS)-based biosensors in diverse applications as well as SERS-directed bio-imaging, which is considered as an emerging sector for monitoring stem cell differentiation, and detection and treatment of cancer.

Transition from Ignition to Flame Growth under External Radiation in 3D

NASA Technical Reports Server (NTRS)

Kashiwagi, Takashi; Nakamura, Yuji; Mell, William E.; Olson, Sandra L.

2004-01-01

This study focuses on localized ignition by external radiant flux and subsequent flame growth over thin polymeric materials (plastic and paper) in microgravity. Two transition stages were observed. The first transition stage covers the period from the onset of ignition to the formation of stabilized flame near the ignited area. This is followed by the second transition of the flame growth stage from the initial stabilized flame to sustained fire growth away from the ignited area. For the first stage, ignition experiments of thin PMMA sheets were conducted using a CO2 laser as an external source in the 10 s drop tower. The results of front side surface ignition and of backside surface ignition were observed. The effects of imposed flow velocity, sample thickness, and ambient oxygen concentration on ignition are obtained. Numerical study was conducted to investigate to understand and predict ignition behavior observed in the experiments. For the second stage, numerical study is being conducted to describe the effects of gravity on heat release rate of a PMMA sheet. The gravity level was varied from zero to normal gravity. The preliminary results show that the maximum heat release occurs at around 0.02 g.

Interplay of Electrostatics and Hydrophobic Effects in the Metamorphic Protein Human Lymphotactin.

PubMed

Korkmaz, Elif Nihal; Volkman, Brian F; Cui, Qiang

2015-07-30

The human lymphotactin (hLtn) is a protein that features two native states both of which are physiologically relevant: it is a monomer (hLtn10) at 10 °C with 200 mM salt and a dimer (hLtn40) at 40 °C and without salt. Here we focus on the networks of electrostatic and hydrophobic interactions that display substantial changes upon the conversion from hLtn10 to hLtn40 since they are expected to modulate the relative stability of the two folds. In addition to the Arg 23-Arg 43 interaction discussed in previous work, we find several other like-charge pairs that are likely important to the stability of hLtn10. Free energy perturbation calculations are carried out to explicitly evaluate the contribution of the Arg 23-Arg 43 interaction to the hLtn10 stability. hLtn40 features a larger number of salt bridges, and a set of hydrophobic residues undergo major changes in the solvent accessible surface area between hLtn10 and hLtn40, pointing to their importance to the relative stability of the two folds. We also discuss the use of explicit and implicit solvent simulations for characterizing the conformational ensembles under different solution conditions.

Gaze and viewing angle influence visual stabilization of upright posture

PubMed Central

Ustinova, KI; Perkins, J

2011-01-01

Focusing gaze on a target helps stabilize upright posture. We investigated how this visual stabilization can be affected by observing a target presented under different gaze and viewing angles. In a series of 10-second trials, participants (N = 20, 29.3 ± 9 years of age) stood on a force plate and fixed their gaze on a figure presented on a screen at a distance of 1 m. The figure changed position (gaze angle: eye level (0°), 25° up or down), vertical body orientation (viewing angle: at eye level but rotated 25° as if leaning toward or away from the participant), or both (gaze and viewing angle: 25° up or down with the rotation equivalent of a natural visual perspective). Amplitude of participants’ sagittal displacement, surface area, and angular position of the center of gravity (COG) were compared. Results showed decreased COG velocity and amplitude for up and down gaze angles. Changes in viewing angles resulted in altered body alignment and increased amplitude of COG displacement. No significant changes in postural stability were observed when both gaze and viewing angles were altered. Results suggest that both the gaze angle and viewing perspective may be essential variables of the visuomotor system modulating postural responses. PMID:22398978

Are metal-organic frameworks able to provide a new generation of solid-phase microextraction coatings? - A review.

PubMed

Rocío-Bautista, Priscilla; Pacheco-Fernández, Idaira; Pasán, Jorge; Pino, Verónica

2016-10-05

Solid-phase microextraction (SPME) is a powerful technique commonly used in sample preparation for extraction/preconcentration of analytes from a wide variety of samples. Among the trends in improving SPME applications, current investigations are focused on the development of novel coatings able to improve the extraction efficiency, sensitivity, and thermal and mechanical stability, within other properties, of current commercial SPME fibers. Metal-organic frameworks (MOFs) merit to be highlighted as promising sorbent materials in SPME schemes. MOFs are porous hybrid materials composed by metal ions and organic linkers, presenting the highest surface areas known, with ease synthesis and high tuneability, together with adequate chemical and thermal stability. For MOF based-SPME fibers, it results important to pretreat adequately the SPME supports to ensure the correct formation of the MOF onto the fiber or the attachment MOF-support. This, in turn, will increase the final stability of the fiber while generating uniform coatings. This review provides a critical overview of the current state of the use of MOFs as SPME coatings, not only highlighting the advantages of these materials versus commercial SPME coatings in terms of stability, selectivity, and sensitivity; but also insightfully describing the current methods to obtain reproducible MOF-based SPME coatings. Copyright © 2016 Elsevier B.V. All rights reserved.

Positives and pathologies of natural resource management on private land-conservation areas.

PubMed

Clements, Hayley S; Cumming, Graeme S

2017-06-01

In managed natural resource systems, such as fisheries and rangelands, there is a recognized trade-off between managing for short-term benefits and managing for longer term resilience. Management actions that stabilize ecological attributes or processes can improve productivity in the supply of ecosystem goods and services in the short term but erode system resilience at longer time scales. For example, fire suppression in rangelands can increase grass biomass initially but ultimately result in an undesirable, shrub-dominated system. Analyses of this phenomenon have focused largely on how management actions influence slow-changing biophysical system attributes (such as vegetation composition). Data on the frequency of management actions that reduce natural ecological variation on 66 private land-conservation areas (PLCAs) in South Africa were used to investigate how management actions are influenced by manager decision-making approaches, a largely ignored part of the problem. The pathology of natural resource management was evident on some PLCAs: increased focus on revenue-generation in decision making resulted in an increased frequency of actions to stabilize short-term variation in large mammal populations, which led to increased revenues from ecotourism or hunting. On many PLCAs, these management actions corresponded with a reduced focus on ecological monitoring and an increase in overstocking of game (i.e., ungulate species) and stocking of extralimitals (i.e., game species outside their historical range). Positives in natural resource management also existed. Some managers monitored slower changing ecological attributes, which resulted in less-intensive management, fewer extralimital species, and lower stocking rates. Our unique, empirical investigation of monitoring-management relationships illustrates that management decisions informed by revenue monitoring versus ecological monitoring can have opposing consequences for natural resource productivity and sustainability. Promoting management actions that maintain resilience in natural resource systems therefore requires cognizance of why managers act the way they do and how these actions can gradually shift managers toward unsustainable strategies. © 2016 Society for Conservation Biology.

Modeling regional initiation of rainfall-induced shallow landslides in the eastern Umbria Region of central Italy

USGS Publications Warehouse

Salciarini, D.; Godt, J.W.; Savage, W.Z.; Conversini, P.; Baum, R.L.; Michael, J.A.

2006-01-01

We model the rainfall-induced initiation of shallow landslides over a broad region using a deterministic approach, the Transient Rainfall Infiltration and Grid-based Slope-stability (TRIGRS) model that couples an infinite-slope stability analysis with a one-dimensional analytical solution for transient pore pressure response to rainfall infiltration. This model permits the evaluation of regional shallow landslide susceptibility in a Geographic Information System framework, and we use it to analyze susceptibility to shallow landslides in an area in the eastern Umbria Region of central Italy. As shown on a landslide inventory map produced by the Italian National Research Council, the area has been affected in the past by shallow landslides, many of which have transformed into debris flows. Input data for the TRIGRS model include time-varying rainfall, topographic slope, colluvial thickness, initial water table depth, and material strength and hydraulic properties. Because of a paucity of input data, we focus on parametric analyses to calibrate and test the model and show the effect of variation in material properties and initial water table conditions on the distribution of simulated instability in the study area in response to realistic rainfall. Comparing the results with the shallow landslide inventory map, we find more than 80% agreement between predicted shallow landslide susceptibility and the inventory, despite the paucity of input data.

Attentional Focus Effects as a Function of Task Difficulty

ERIC Educational Resources Information Center

Wulf, Gabriele; Tollner, Thomas; Shea, Charles H.

2007-01-01

The purpose of the present study was to examine whether the advantages of adopting an external focus would be seen primarily for relatively challenging (postural stability) tasks but not less demanding tasks. To examine this, the authors used balance tasks that imposed increased challenges to maintaining stability. The present results support the…

Transient stability enhancement of modern power grid using predictive Wide-Area Monitoring and Control

NASA Astrophysics Data System (ADS)

Yousefian, Reza

This dissertation presents a real-time Wide-Area Control (WAC) designed based on artificial intelligence for large scale modern power systems transient stability enhancement. The WAC using the measurements available from Phasor Measurement Units (PMUs) at generator buses, monitors the global oscillations in the system and optimally augments the local excitation system of the synchronous generators. The complexity of the power system stability problem along with uncertainties and nonlinearities makes the conventional modeling non-practical or inaccurate. In this work Reinforcement Learning (RL) algorithm on the benchmark of Neural Networks (NNs) is used to map the nonlinearities of the system in real-time. This method different from both the centralized and the decentralized control schemes, employs a number of semi-autonomous agents to collaborate with each other to perform optimal control theory well-suited for WAC applications. Also, to handle the delays in Wide-Area Monitoring (WAM) and adapt the RL toward the robust control design, Temporal Difference (TD) is proposed as a solver for RL problem or optimal cost function. However, the main drawback of such WAC design is that it is challenging to determine if an offline trained network is valid to assess the stability of the power system once the system is evolved to a different operating state or network topology. In order to address the generality issue of NNs, a value priority scheme is proposed in this work to design a hybrid linear and nonlinear controllers. The algorithm so-called supervised RL is based on mixture of experts, where it is initialized by linear controller and as the performance and identification of the RL controller improves in real-time switches to the other controller. This work also focuses on transient stability and develops Lyapunov energy functions for synchronous generators to monitor the stability stress of the system. Using such energies as a cost function guarantees the convergence toward optimal post-fault solutions. These energy functions are developed on inter-area oscillations of the system identified online with Prony analysis. Finally, this work investigates the impacts of renewable energy resources, in specific Doubly Fed Induction Generator (DFIG)-based wind turbines, on power system transient stability and control. As the penetration of such resources is increased in transmission power system, neglecting the impacts of them will make the WAC design non-realistic. An energy function is proposed for DFIGs based on their dynamic performance in transient disturbances. Further, this energy is augmented to synchronous generators' energy as a global cost function, which is minimized by the WAC signals. We discuss the relative advantages and bottlenecks of each architecture and methodology using dynamic simulations of several test systems including a 2-area 8 bus system, IEEE 39 bus system, and IEEE 68 bus system in EMTP and real-time simulators. Being nonlinear-based, fast, accurate, and non-model based design, the proposed WAC system shows better transient and damping response when compared to conventional control schemes and local PSSs.

Slope Stability Analysis In Seismic Areas Of The Northern Apennines (Italy)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lo Presti, D.; Fontana, T.; Marchetti, D.

2008-07-08

Several research works have been published on the slope stability in the northern Tuscany (central Italy) and particularly in the seismic areas of Garfagnana and Lunigiana (Lucca and Massa-Carrara districts), aimed at analysing the slope stability under static and dynamic conditions and mapping the landslide hazard. In addition, in situ and laboratory investigations are available for the study area, thanks to the activities undertaken by the Tuscany Seismic Survey. Based on such a huge information the co-seismic stability of few ideal slope profiles have been analysed by means of Limit equilibrium method LEM - (pseudo-static) and Newmark sliding block analysismore » (pseudo-dynamic). The analysis--results gave indications about the most appropriate seismic coefficient to be used in pseudo-static analysis after establishing allowable permanent displacement. Such indications are commented in the light of the Italian and European prescriptions for seismic stability analysis with pseudo-static approach. The stability conditions, obtained from the previous analyses, could be used to define microzonation criteria for the study area.« less

Stabilizing Conditional Standard Errors of Measurement in Scale Score Transformations

ERIC Educational Resources Information Center

Moses, Tim; Kim, YoungKoung

2017-01-01

The focus of this article is on scale score transformations that can be used to stabilize conditional standard errors of measurement (CSEMs). Three transformations for stabilizing the estimated CSEMs are reviewed, including the traditional arcsine transformation, a recently developed general variance stabilization transformation, and a new method…

Enhanced methodology of focus control and monitoring on scanner tool

NASA Astrophysics Data System (ADS)

Chen, Yen-Jen; Kim, Young Ki; Hao, Xueli; Gomez, Juan-Manuel; Tian, Ye; Kamalizadeh, Ferhad; Hanson, Justin K.

2017-03-01

As the demand of the technology node shrinks from 14nm to 7nm, the reliability of tool monitoring techniques in advanced semiconductor fabs to achieve high yield and quality becomes more critical. Tool health monitoring methods involve periodic sampling of moderately processed test wafers to detect for particles, defects, and tool stability in order to ensure proper tool health. For lithography TWINSCAN scanner tools, the requirements for overlay stability and focus control are very strict. Current scanner tool health monitoring methods include running BaseLiner to ensure proper tool stability on a periodic basis. The focus measurement on YIELDSTAR by real-time or library-based reconstruction of critical dimensions (CD) and side wall angle (SWA) has been demonstrated as an accurate metrology input to the control loop. The high accuracy and repeatability of the YIELDSTAR focus measurement provides a common reference of scanner setup and user process. In order to further improve the metrology and matching performance, Diffraction Based Focus (DBF) metrology enabling accurate, fast, and non-destructive focus acquisition, has been successfully utilized for focus monitoring/control of TWINSCAN NXT immersion scanners. The optimal DBF target was determined to have minimized dose crosstalk, dynamic precision, set-get residual, and lens aberration sensitivity. By exploiting this new measurement target design, 80% improvement in tool-to-tool matching, >16% improvement in run-to-run mean focus stability, and >32% improvement in focus uniformity have been demonstrated compared to the previous BaseLiner methodology. Matching <2.4 nm across multiple NXT immersion scanners has been achieved with the new methodology of set baseline reference. This baseline technique, with either conventional BaseLiner low numerical aperture (NA=1.20) mode or advanced illumination high NA mode (NA=1.35), has also been evaluated to have consistent performance. This enhanced methodology of focus control and monitoring on multiple illumination conditions, opens an avenue to significantly reduce Focus-Exposure Matrix (FEM) wafer exposure for new product/layer best focus (BF) setup.

New micro-beam beamline at SPring-8, targeting at protein micro-crystallography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hirata, Kunio; Ueno, Go; Nisawa, Atsushi

2010-06-23

A new protein micro-crystallography beamline BL32XU at SPring-8 is under construction and scheduled to start operation in 2010. The beamline is designed to provide the stabilized and brilliant micro-beam to collect high-quality data from micro-crystals. The beamline consists of a hybrid in-vacuum undulator, a liquid-nitrogen cooled double crystal monochromator, and K-B focusing mirrors with large magnification factor. Development of data acquisition system and end station consists of high-precision diffractometer, high-efficiency area detector, sample auto-changer etc. are also in progress.

Mycorrhizal inoculation as a tool for sustainable bio-engineering measures in steep alpine environments? - Results of a three year field experiment

NASA Astrophysics Data System (ADS)

Bast, Alexander; Wilcke, Wolfgang; Lüscher, Peter; Graf, Frank; Gärtner, Holger

2013-04-01

Global warming is anticipated to result in an increase of heavy precipitation events. In vegetation-free, steep Alpine areas intense rain fall events have distinct influences on erosional processes on slopes. These processes and (shallow) mass movements are directly linked with torrential rain falls, and for this lead to high erosion rates in those regions, resulting in an increased natural and socio-economic damage potential. For restoring and managing erosion-prone sites, bioengineering measures as a tool for hazard prevention gain more importance. Due to the rough environmental conditions, and hence, reduced germination capability and sprout vigour, it is difficult to establish a dense cover of pioneer vegetation. Thus, the question is what can be done to give planted saplings within bioengineering projects maximum support, to develop their above- and belowground structures to promote slope stabilization. Green-house and laboratory experiments have shown that mycorrhizal inoculum has a positive impact on plant development and soil structure, e.g. the formation of (stable) aggregates within several months. Based on these promising results, we intended to apply mycorrhizal inoculation in a field-experiment. In May 2010, we established experimental plots at an erosion-prone talus slope (inclination: ~40 - 45 °; elevation 1220 - 1360 m a.s.l.), located in the Eastern Swiss Alps. The slope, consisting of moraine and denudation-derived substrate, shows high geomorphic activity (e.g. debris flows, rill erosion). Two slope areas, 10m wide and 32m long, were stabilized with 1200 plants each. Additionally, mycorrhiza inoculum (INOQ Forst, 40 ml/plant) was added to one of the two areas. Within the stabilized areas, a mixture of eight saplings was planted per running meter in 15 rows. The assortment included four saplings of green alder and two of purple willow, as well as one tree (maple, birch, ash) and shrub species (e.g. guelder rose, honeysuckle). Finally, both areas were hand-seeded with an Alpine seed-mixture. In addition, a third was selected but not treated, reflecting the natural conditions and serving as a control. Next to analysing aboveground whole-plant traits (e.g. plant height, crown diameter, stem thickness) and leaf traits (e.g. specific leaf area, leaf size, leaf dry matter content, nitrogen and potassium analyses), we also focused on belowground properties. Undisturbed soil cores (0-20cm in depth) allow a determination of a aggregate stability coefficient, the aggregate-size development, as well as root traits (e.g. root length density, fine(root)diameter). Linear mixed-effect models and testing a posteriori contrasts permit a comparison between the different treatments. Preliminary results indicate, that four months after stabilization plant mortality was high over the two treatments, but it was significantly less on the inoculated treatment. In general plant and leaf traits are showing, that plant vitality is higher at the mycorrhizal-treated plots. Examination of belowground properties yield surprising results; the non-inoculated treatment is showing higher aggregate stability coefficients and higher root length density, which is in contrast to laboratory results. Our contribution will highlight the results of the entire three year field experiment.

Marine cloud brightening: regional applications.

PubMed

Latham, John; Gadian, Alan; Fournier, Jim; Parkes, Ben; Wadhams, Peter; Chen, Jack

2014-12-28

The general principle behind the marine cloud brightening (MCB) climate engineering technique is that seeding marine stratocumulus clouds with substantial concentrations of roughly monodisperse sub-micrometre-sized seawater particles might significantly enhance cloud albedo and longevity, thereby producing a cooling effect. This paper is concerned with preliminary studies of the possible beneficial application of MCB to three regional issues: (1) recovery of polar ice loss, (2) weakening of developing hurricanes and (3) elimination or reduction of coral bleaching. The primary focus is on Item 1. We focus discussion herein on advantages associated with engaging in limited-area seeding, regional effects rather than global; and the levels of seeding that may be required to address changing current and near-term conditions in the Arctic. We also mention the possibility that MCB might be capable of producing a localized cooling to help stabilize the West Antarctic Ice Sheet.

Effect of Ionic Soil Stabilizers on Soil-Water Characteristic of Special Clay

NASA Astrophysics Data System (ADS)

Cui, D.; Xiang, W.

2011-12-01

The engineering properties of special clay are conventionally improved through the use of chemical additive such as ionic soil stabilizer (ISS). Such special clays are often referred to as stabilized or treated clays. The soil-water characteristic curves (SWCC) of special clays from Henan province and Hubei province were measured both in natural and stabilized conditions using the pressure plate apparatus in the suction range of 0-500 kPa. The SWCC results are used to interpret the special clays behavior due to stabilizer treatment. In addition, relationships were developed between the basic clay and stabilized properties such as specific surface area and pore size distribution. The analysis showed that specific surface area decreases, cumulative pore volume and average pore size diameter decrease, dehydration rate slows and the thickness of water film thins after treatment with Ionic Soil Stabilizer. The research data and interpretation analysis presented here can be extended to understand the water film change behaviors influencing the mechanical and physical properties of stabilized special clay soils. KEY WORDS: ionic soil stabilizer, special clay, pore size diameter, specific surface area, soil water characteristic curve, water film

Modeling 3-D Slope Stability of Coastal Bluffs Using 3-D Ground-Water Flow, Southwestern Seattle, Washington

USGS Publications Warehouse

Brien, Dianne L.; Reid, Mark E.

2007-01-01

Landslides are a common problem on coastal bluffs throughout the world. Along the coastal bluffs of the Puget Sound in Seattle, Washington, landslides range from small, shallow failures to large, deep-seated landslides. Landslides of all types can pose hazards to human lives and property, but deep-seated landslides are of significant concern because their large areal extent can cause extensive property damage. Although many geomorphic processes shape the coastal bluffs of Seattle, we focus on large (greater than 3,000 m3), deepseated, rotational landslides that occur on the steep bluffs along Puget Sound. Many of these larger failures occur in advance outwash deposits of the Vashon Drift (Qva); some failures extend into the underlying Lawton Clay Member of the Vashon Drift (Qvlc). The slope stability of coastal bluffs is controlled by the interplay of three-dimensional (3-D) variations in gravitational stress, strength, and pore-water pressure. We assess 3-D slope-stability using SCOOPS (Reid and others, 2000), a computer program that allows us to search a high-resolution digital-elevation model (DEM) to quantify the relative stability of all parts of the landscape by computing the stability and volume of thousands of potential spherical failures. SCOOPS incorporates topography, 3-D strength variations, and 3-D pore pressures. Initially, we use our 3-D analysis methods to examine the effects of topography and geology by using heterogeneous material properties, as defined by stratigraphy, without pore pressures. In this scenario, the least-stable areas are located on the steepest slopes, commonly in Qva or Qvlc. However, these locations do not agree well with observations of deep-seated landslides. Historically, both shallow colluvial landslides and deep-seated landslides have been observed near the contact between Qva and Qvlc, and commonly occur in Qva. The low hydraulic conductivity of Qvlc impedes ground-water flow, resulting in elevated pore pressures at the base of Qva, thereby increasing the potential for landslides. Our analysis simulates the ground-water flow using the results of a 3-D ground-water flow model, MODFLOW-2000 (Harbaugh and others, 2000), to generate a 3-D pore-pressure field. Areas of elevated pore pressure reflect the influence of a perched ground-water table in Qva, as well as ground-water convergence in the coastal re-entrants. We obtain a realistic model of deep-seated landsliding by combining 3-D pore pressures with heterogeneous strength properties. The results show the least-stable areas where pore pressures are locally elevated in Qva. We compare our results with records of past landslides. The predicted leaststable areas include two historically active deep-seated landslides and areas adjacent to these landslides.

Focusing of active particles in a converging flow

DOE PAGES

Potomkin, Mykhailo; Kaiser, Andreas; Berlyand, Leonid; ...

2017-10-20

We consider active particles swimming in a convergent fluid flow in a trapezoid nozzle with no-slip walls. We use mathematical modeling to analyze trajectories of these particles inside the nozzle. By extensive Monte Carlo simulations, we show that trajectories are strongly affected by the background fluid flow and geometry of the nozzle leading to wall accumulation and upstream motion (rheotaxis). In particular, we describe the non-trivial focusing of active rods depending on physical and geometrical parameters. It is also established that the convergent component of the background flow leads to stability of both downstream and upstream swimming at the centerline.more » The stability of downstream swimming enhances focusing, and the stability of upstream swimming enables rheotaxis in the bulk.« less

ACS from development to operations

NASA Astrophysics Data System (ADS)

Caproni, Alessandro; Colomer, Pau; Jeram, Bogdan; Sommer, Heiko; Chiozzi, Gianluca; Mañas, Miguel M.

2016-08-01

The ALMA Common Software (ACS), provides the infrastructure of the distributed software system of ALMA and other projects. ACS, built on top of CORBA and Data Distribution Service (DDS) middleware, is based on a Component- Container paradigm and hides the complexity of the middleware allowing the developer to focus on domain specific issues. The transition of the ALMA observatory from construction to operations brings with it that ACS effort focuses primarily on scalability, stability and robustness rather than on new features. The transition came together with a shorter release cycle and a more extensive testing. For scalability, the most problematic area has been the CORBA notification service, used to implement the publisher subscriber pattern because of the asynchronous nature of the paradigm: a lot of effort has been spent to improve its stability and recovery from run time errors. The original bulk data mechanism, implemented using the CORBA Audio/Video Streaming Service, showed its limitations and has been replaced with a more performant and scalable DDS implementation. Operational needs showed soon the difference between releases cycles for Online software (i.e. used during observations) and Offline software, which requires much more frequent releases. This paper attempts to describe the impact the transition from construction to operations had on ACS, the solution adopted so far and a look into future evolution.

Reforestation strategies amid social instability: lessons from Afghanistan.

PubMed

Groninger, John W

2012-04-01

Foreign and domestic government agencies and other international organizations pursue reforestation programs in rural upper watershed areas of Afghanistan over the past decade to alleviate poverty, combat the insurgency and rehabilitate a depleted forest resource base. Popular programs incorporate cash-for-work to conduct hillside terracing, check dam construction and tree-planting for nut production, fuel wood, timber, dune stabilization, and erosion abatement. Programmatic approaches have varied as a function of accessibility, security and local objectives. Uncertain land tenure and use rights, weak local environmental management capacity, and a focus on agricultural production to meet immediate needs limit interest, nationally and locally. Unreliable security, a lack of high quality tree planting stock, limited technical knowledge and coordination among government agencies, and poor security hamper program expansion. Reforestation success would be most likely where these issues are least acute. The Afghan government should focus on supporting community based natural resource management, developing and disseminating improved conservation tree nursery strategies, and promoting watershed management schemes that incorporate forestry, range management and agronomic production. Reforestation practitioners could benefit from the human and material resources now present as part of the international war effort. Successes and failures encountered in Afghanistan should be considered in order to address similar problems in insecure regions elsewhere when reforestation may help reverse environmental degradation and contribute to broader social stabilization efforts.

Reforestation Strategies Amid Social Instability: Lessons from Afghanistan

NASA Astrophysics Data System (ADS)

Groninger, John W.

2012-04-01

Foreign and domestic government agencies and other international organizations pursue reforestation programs in rural upper watershed areas of Afghanistan over the past decade to alleviate poverty, combat the insurgency and rehabilitate a depleted forest resource base. Popular programs incorporate cash-for-work to conduct hillside terracing, check dam construction and tree-planting for nut production, fuel wood, timber, dune stabilization, and erosion abatement. Programmatic approaches have varied as a function of accessibility, security and local objectives. Uncertain land tenure and use rights, weak local environmental management capacity, and a focus on agricultural production to meet immediate needs limit interest, nationally and locally. Unreliable security, a lack of high quality tree planting stock, limited technical knowledge and coordination among government agencies, and poor security hamper program expansion. Reforestation success would be most likely where these issues are least acute. The Afghan government should focus on supporting community based natural resource management, developing and disseminating improved conservation tree nursery strategies, and promoting watershed management schemes that incorporate forestry, range management and agronomic production. Reforestation practitioners could benefit from the human and material resources now present as part of the international war effort. Successes and failures encountered in Afghanistan should be considered in order to address similar problems in insecure regions elsewhere when reforestation may help reverse environmental degradation and contribute to broader social stabilization efforts.

Use of a remotely piloted aircraft system for hazard assessment in a rocky mining area (Lucca, Italy)

NASA Astrophysics Data System (ADS)

Salvini, Riccardo; Mastrorocco, Giovanni; Esposito, Giuseppe; Di Bartolo, Silvia; Coggan, John; Vanneschi, Claudio

2018-01-01

The use of remote sensing techniques is now common practice in different working environments, including engineering geology. Moreover, in recent years the development of structure from motion (SfM) methods, together with rapid technological improvement, has allowed the widespread use of cost-effective remotely piloted aircraft systems (RPAS) for acquiring detailed and accurate geometrical information even in evolving environments, such as mining contexts. Indeed, the acquisition of remotely sensed data from hazardous areas provides accurate 3-D models and high-resolution orthophotos minimizing the risk for operators. The quality and quantity of the data obtainable from RPAS surveys can then be used for inspection of mining areas, audit of mining design, rock mass characterizations, stability analysis investigations and monitoring activities. Despite the widespread use of RPAS, its potential and limitations still have to be fully understood.In this paper a case study is shown where a RPAS was used for the engineering geological investigation of a closed marble mine area in Italy; direct ground-based techniques could not be applied for safety reasons. In view of the re-activation of mining operations, high-resolution images taken from different positions and heights were acquired and processed using SfM techniques to obtain an accurate and detailed 3-D model of the area. The geometrical and radiometrical information was subsequently used for a deterministic rock mass characterization, which led to the identification of two large marble blocks that pose a potential significant hazard issue for the future workforce. A preliminary stability analysis, with a focus on investigating the contribution of potential rock bridges, was then performed in order to demonstrate the potential use of RPAS information in engineering geological contexts for geohazard identification, awareness and reduction.

Regional landslide-hazard assessment for Seattle, Washington, USA

USGS Publications Warehouse

Baum, R.L.; Coe, J.A.; Godt, J.W.; Harp, E.L.; Reid, M.E.; Savage, W.Z.; Schulz, W.H.; Brien, D.L.; Chleborad, A.F.; McKenna, J.P.; Michael, J.A.

2005-01-01

Landslides are a widespread, frequent, and costly hazard in Seattle and the Puget Sound area of Washington State, USA. Shallow earth slides triggered by heavy rainfall are the most common type of landslide in the area; many transform into debris flows and cause significant property damage or disrupt transportation. Large rotational and translational slides, though less common, also cause serious property damage. The hundreds of landslides that occurred during the winters of 1995-96 and 1996-97 stimulated renewed interest by Puget Sound communities in identifying landslide-prone areas and taking actions to reduce future landslide losses. Informal partnerships between the U.S. Geological Survey (USGS), the City of Seattle, and private consultants are focusing on the problem of identifying and mapping areas of landslide hazard as well as characterizing temporal aspects of the hazard. We have developed GIS-based methods to map the probability of landslide occurrence as well as empirical rainfall thresholds and physically based methods to forecast times of landslide occurrence. Our methods for mapping landslide hazard zones began with field studies and physically based models to assess relative slope stability, including the effects of material properties, seasonal groundwater levels, and rainfall infiltration. We have analyzed the correlation between historic landslide occurrence and relative slope stability to map the degree of landslide hazard. The City of Seattle is using results of the USGS studies in storm preparedness planning for emergency access and response, planning for development or redevelopment of hillsides, and municipal facility planning and prioritization. Methods we have developed could be applied elsewhere to suit local needs and available data.

Characterizing Land Surface Change and Levee Stability in the Sacramento-San Joaquin Delta Using UAVSAR Radar Imagery

NASA Technical Reports Server (NTRS)

Jones, Cathleen; Bawden, Gerald; Deverel, Steven; Dudas, Joel; Hensley, Scott

2011-01-01

The Sacramento-San Joaquin Delta is one of the primary water sources for the state of California and represents a complex geographical area comprised of tidal marshland, levee rimmed islands that are used primarily for agriculture, and urban encroachment. Land subsidence has dropped many of the Delta islands 3 to >7 meters below mean sea level and requires nearly 1700 km of levees to maintain the integrity of the islands and flow of water through the Delta. The current average subsidence rates for each island varies, with 1.23 cm/yr on Sherman Island and 2.2 cm/yr for Bacon Island, as determined by ground-based instruments located at isolated points in the Delta. The Delta's status as the most critical water resource for the state, an endangered ecosystem, and an area continuously threatened with levee breakage from hydrostatic pressure and the danger of earthquakes on several major faults in the San Francisco area make it a focus of monitoring efforts by both the state and national government. This activity is now almost entirely done by ground-based efforts, but the benefits of using remote sensing for wide scale spatial coverage and frequent temporal coverage is obvious. The UAVSAR airborne polarimetric and differential interferometric L-band synthetic aperture radar system has been used to collected monthly images of the Sacramento-San Joaquin Delta and much of the adjacent Suisun Marsh since July 2009 to characterize levee stability, image spatially varied subsidence, and assess how well the UAVSAR performs in an area with widespread agriculture production.

Evaluating Red Reflex and Surgeon Preference Between Nearly-Collimated and Focused Beam Microscope Illumination Systems.

PubMed

Cionni, Robert J; Pei, Ron; Dimalanta, Ramon; Lubeck, David

2015-08-01

To evaluate the intensity and stability of the red reflex produced by ophthalmic surgical microscopes with nearly-collimated versus focused illumination systems and to assess surgeon preference in a simulated surgical setting. This two-part evaluation consisted of postproduction surgical video analysis of red reflex intensity and a microscope use and preference survey completed by 13 experienced cataract surgeons. Survey responses were based on bench testing and experience in a simulated surgical setting. A microscope with nearly-collimated beam illumination and two focused beam microscopes were assessed. Red reflex intensity and stability were greater with the nearly-collimated microscope illumination system. In the bench testing survey, surgeons reported that the red reflex was maintained over significantly greater distances away from pupillary center, and depth of focus was numerically greater with nearly-collimated illumination relative to focused illumination. Most participating surgeons (≥64%) reported a preference for the microscope with nearly-collimated illumination with regard to red reflex stability, depth of focus, visualization, surgical working distance, and perceived patient comfort. The microscope with nearly-collimated illumination produced a more intense and significantly more stable red reflex and was preferred overall by more surgeons. This is the first report of an attempt to quantify red reflex intensity and stability and to evaluate surgically-relevant parameters between microscope systems. The data and methods presented here may provide a basis for future studies attempting to quantify differences between surgical microscopes that may affect surgeon preference and microscope use in ophthalmic surgery.

Scale dependence of the diversity-stability relationship in a temperate grassland.

PubMed

Zhang, Yunhai; He, Nianpeng; Loreau, Michel; Pan, Qingmin; Han, Xingguo

2018-05-01

A positive relationship between biodiversity and ecosystem stability has been reported in many ecosystems; however, it has yet to be determined whether and how spatial scale affects this relationship. Here, for the first time, we assessed the effects of alpha, beta and gamma diversity on ecosystem stability and the scale dependence of the slope of the diversity-stability relationship.By employing a long-term (33 years) dataset from a temperate grassland, northern China, we calculated the all possible spatial scales with the complete combination from the basic 1-m 2 plots.Species richness was positively associated with ecosystem stability through species asynchrony and overyielding at all spatial scales (1, 2, 3, 4 and 5 m 2 ). Both alpha and beta diversity were positively associated with gamma stability.Moreover, the slope of the diversity-area relationship was significantly higher than that of the stability-area relationship, resulting in a decline of the slope of the diversity-stability relationship with increasing area. Synthesis. With the positive species diversity effect on ecosystem stability from small to large spatial scales, our findings demonstrate the need to maintain a high biodiversity and biotic heterogeneity as insurance against the risks incurred by ecosystems in the face of global environmental changes.

Stability improvement of wind turbine penetrated using power system stabilizer (PSS) on South Sulawesi transmission system

NASA Astrophysics Data System (ADS)

Siswanto, Agus; Gunadin, Indar Chaerah; Said, Sri Mawar; Suyuti, Ansar

2018-03-01

The purpose of this research is to improve the stability of interconnection of South Sulawesi system caused by penetration new wind turbine in Sidrap area on bus 2 and in Jeniponto area on bus 34. The method used in this research was via software Power System analysis Toolbox (PSAT) under MATLAB. In this research, there are two problems that are evaluated, the stability of the system before and after penetration wind turbine into the system South Sulawesi system. From the simulation result shows that penetration of wind turbine on bus 2 Sidrap, bus 37 Jeniponto give effect oscillation on the system. The oscillation was damped by installation of Power System Stabilizer (PSS) on bus 29 area Sungguminasa, that South Sulawesi system stable according to normal condition.

Highly stable organic field-effect transistors with engineered gate dielectrics (Conference Presentation)

NASA Astrophysics Data System (ADS)

Kippelen, Bernard; Wang, Cheng-Yin; Fuentes-Hernandez, Canek; Yun, Minseong; Singh, Ankit K.; Dindar, Amir; Choi, Sangmoo; Graham, Samuel

2016-11-01

Organic field-effect transistors (OFETs) have the potential to lead to low-cost flexible displays, wearable electronics, and sensors. While recent efforts have focused greatly on improving the maximum charge mobility that can be achieved in such devices, studies about the stability and reliability of such high performance devices are relatively scarce. In this talk, we will discuss the results of recent studies aimed at improving the stability of OFETs under operation and their shelf lifetime. In particular, we will focus on device architectures where the gate dielectric is engineered to act simultaneously as an environmental barrier layer. In the past, our group had demonstrated solution-processed top-gate OFETs using TIPS-pentacene and PTAA blends as a semiconductor layer with a bilayer gate dielectric layer of CYTOP/Al2O3, where the oxide layer was fabricated by atomic layer deposition, ALD. Such devices displayed high operational stability with little degradation after 20,000 on/off scan cycles or continuous operation (24 h), and high environmental stability when kept in air for more than 2 years, with unchanged carrier mobility. Using this stable device geometry, simple circuits and sensors operating in aqueous conditions were demonstrated. However, the Al2O3 layer was found to degrade due to corrosion under prolonged exposure in aqueous solutions. In this talk, we will report on the use of a nanolaminate (NL) composed of Al2O3 and HfO2 by ALD to replace the Al2O3 single layer in the bilayer gate dielectric use in top-gate OFETs. Such OFETs were found to operate under harsh condition such as immersion in water at 95 °C. This work was funded by the Department of Energy (DOE) through the Bay Area Photovoltaics Consortium (BAPVC) under Award Number DE-EE0004946.

Characterization, monitoring, and sensor technology crosscutting program: Technology summary

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1995-06-01

The purpose of the Characterization, Monitoring, and Sensor Technology Crosscutting Program (CMST-CP) is to deliver appropriate characterization, monitoring, and sensor technology (CMST) to the Office of Waste Management (EM-30), the Office of Environmental Restoration (EM-40), and the Office of Facility Transition and Management (EM-60). The technology development must also be cost effective and appropriate to EM-30/40/60 needs. Furthermore, the required technologies must be delivered and implemented when needed. Accordingly, and to ensure that available DOE and other national resources are focused an the most pressing needs, management of the technology development is concentrated on the following Focus Areas: Contaminant Plumemore » Containment and Remediation (PFA); Landfill Stabilization (LSFA); High-Level Waste Tank Remediation (TFA); Mixed Waste Characterization, Treatment, and Disposal (MWFA); and Facility Deactivation, Decommissioning, and Material Disposition (FDDMDFA). Brief descriptions of CMST-CP projects funded in FY95 are presented.« less

Stability measures in arid ecosystems

NASA Astrophysics Data System (ADS)

Nosshi, M. I.; Brunsell, N. A.; Koerner, S.

2015-12-01

Stability, the capacity of ecosystems to persist in the face of change, has proven its relevance as a fundamental component of ecological theory. Here, we would like to explore meaningful and quantifiable metrics to define stability, with a focus on highly variable arid and semi-arid savanna ecosystems. Recognizing the importance of a characteristic timescale to any definition of stability, our metrics will be focused scales from annual to multi-annual, capturing different aspects of stability. Our three measures of stability, in increasing order of temporal scale, are: (1) Ecosystem resistance, quantified as the degree to which the system maintains its mean state in response to a perturbation (drought), based on inter-annual variability in Normalized Difference Vegetation Index (NDVI). (2) An optimization approach, relevant to arid systems with pulse dynamics, that models vegetation structure and function based on a trade off between the ability to respond to resource availability and avoid stress. (3) Community resilience, measured as species turnover rate (β diversity). Understanding the nature of stability in structurally-diverse arid ecosystems, which are highly variable, yields theoretical insight which has practical implications.

76 FR 13072 - Airworthiness Directives; Saab AB, Saab Aerosystems Model SAAB 2000 Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-10

... important to the structural integrity of the horizontal stabilizer. Corrosion damage in these areas, if not... structural integrity of the horizontal stabilizer. Corrosion damage in these areas, if not detected and... convoluted tubing on the harness, applying corrosion prevention compound to the inspected area, making sure...

75 FR 77796 - Airworthiness Directives; Saab AB, Saab Aerosystems Model SAAB 2000 Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-14

... of the horizontal stabilizer. Corrosion damage in these areas, if not detected and corrected, can... of the horizontal stabilizer. Corrosion damage in these areas, if not detected and corrected, can... convoluted tubing on the harness, applying corrosion prevention compound to the inspected area, making sure...

Static postural stability in women with stress urinary incontinence: Effects of vision and bladder filling.

PubMed

Chmielewska, Daria; Stania, Magdalena; Słomka, Kajetan; Błaszczak, Edward; Taradaj, Jakub; Dolibog, Patrycja; Juras, Grzegorz

2017-11-01

This case-control study was designed to compare static postural stability between women with stress urinary incontinence and continent women and it was hypothesized that women with incontinence aged around 50 years also have balance disorders. Eighteen women with incontinence and twelve women without incontinence aged 50-55 years participated in two 60-s trials of each of four different testing conditions: eyes open/full bladder, eyes open/empty bladder, eyes closed/full bladder, eyes closed/empty bladder. The center of foot pressure (COP): sway range, root mean square, velocity (in the antero-posterior and medio-lateral directions), and COP area were recorded. The stabilograms were decomposed into rambling and trembling components. The groups of women with and without incontinence differed during the full bladder condition in antero-posterior COP sway range, COP area, and rambling trajectory (range in the antero-posterior and medio-lateral directions, root mean square in the antero-posterior and medio-lateral directions and velocity in the antero-posterior direction). The women with incontinence had more difficulty controlling their postural balance than continent women while standing with a full bladder. Therefore, developing therapeutic management focused on strengthening the women's core muscles and improving their postural balance seems advisable. © 2017 Wiley Periodicals, Inc.

Postural stability of biped robots and the foot-rotation indicator (FRI) point

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goswami, A.

1999-06-01

The focus of this paper is the problem of foot rotation in biped robots during the single-support phase. Foot rotation is an indication of postural instability, which should be carefully treated in a dynamically stable walk and avoided altogether in a statically stable walk. The author introduces the foot-rotation indicator (FRI) point, which is a point on the foot/ground-contact surface where the net ground-reaction force would have to act to keep the foot stationary. To ensure no foot rotation, the FRI point must remain within the convex hull of the foot-support area. In contrast with the ground projection of themore » center of mass (GCoM), which is a static criterion, the FRI point incorporates robot dynamics. As opposed to the center of pressure (CoP) -- better known as the zero-moment point (ZMP) in the robotics literature -- which may not leave the support area, the FRI point may leave the area. In fact, the position of the FRI point outside the footprint indicates the direction of the impending rotation and the magnitude of rotational moment acting on the foot. Owing to these important properties, the FRI point helps not only to monitor the state of postural stability of a biped robot during the entire gait cycle, but indicates the severity of instability of the gait as well. In response to a recent need, the paper also resolves the misconceptions surrounding the CoP/ZMP equivalence.« less

Monitoring Ground Deformation Using Persistent Scatters Interferometry (PSI) and Small Baselines (SBAS) Techniques Integrated in the ESA RSS Service: The Case Study of Valencia, Rome and South Sardinia

NASA Astrophysics Data System (ADS)

Delgado, Manuel J.; Cuccu, Roberto; Rivolta, Giancarlo

2015-05-01

This work is focused on the infrastructure monitoring of areas which had experienced significant urbanization and therefore, also an increase of the exploitation of natural resources. Persistent Scatters Interferometry (PS-InSAR) and Small Baselines (SBAS) approaches are applied to three study areas for which large datasets of SAR images are available in ascending and descending modes to finally deploy deformation maps of different buildings and infrastructures. Valencia, Rome and South Sardinia areas have been selected for this study, having experienced an increase of the exploitation of natural resources in parallel with their urban expansion. Moreover, Rome is a very special case, where Cultural Heritage permeating the city and its surroundings would suggest the necessity of a tool for monitoring the stability of the different sites. This work wants to analyse the potential deformation that had occurred in these areas during the period 1992 to 2010, by applying Persistent Scatters Interferometry to ESA ERS SAR and Envisat ASAR data.

No Heat Spray Drying Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beetz, Charles

No Heat Spray Drying Technology. ZoomEssence has developed our Zooming™ spray drying technology that atomizes liquids to powders at ambient temperature. The process of drying a liquid into a powder form has been traditionally achieved by mixing a heated gas with an atomized (sprayed) fluid within a vessel (drying chamber) causing the solvent to evaporate. The predominant spray drying process in use today employs air heated up to 400° Fahrenheit to dry an atomized liquid into a powder. Exposing sensitive, volatile liquid ingredients to high temperature causes molecular degradation that negatively impacts solubility, stability and profile of the powder. Inmore » short, heat is detrimental to many liquid ingredients. The completed award focused on several areas in order to advance the prototype dryer to a commercial scale integrated pilot system. Prior to the award, ZoomEssence had developed a prototype ‘no-heat’ dryer that firmly established the feasibility of the Zooming™ process. The award focused on three primary areas to improve the technology: (1) improved ability to formulate emulsions for specific flavor groups and improved understanding of the relationship of emulsion properties to final dry particle properties, (2) a new production atomizer, and (3) a dryer controls system.« less

Mercury contamination - Amalgamate (contract with NFS and ADA). Stabilize Elemental Mercury Wastes. Mixed Waste Focus Area. OST Reference Number 1675

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

1999-09-01

Through efforts led by the Mixed Waste Focus Area (MWFA) and its Mercury Working Group (HgWG), the inventory of bulk elemental mercury contaminated with radionuclides stored at various U. S. Department of Energy (DOE) sites is thought to be approximately 16 m3 (Conley et al. 1998). At least 19 different DOE sites have this type of mixed low-level waste in their storage facilities. The U. S. Environmental Protection Agency (EPA) specifies amalgamation as the treatment method for radioactively contaminated elemental mercury. Although the chemistry of amalgamation is well known, the practical engineering of a sizable amalgamation process has not beenmore » tested (Tyson 1993). To eliminate the existing DOE inventory in a reasonable timeframe, scaleable equipment is needed that can: produce waste forms that meet the EPA definition of amalgamation, produce waste forms that pass the EPA Toxicity Characteristic Leaching Procedure (TCLP) limit of 0.20 mg/L, limit mercury vapor concentrations during processing to below the Occupational Safety and Health Administration’s (OSHA) 8-hour worker exposure limit (50 mg/m3) for mercury, and perform the above economically.« less

Combination of bubble liposomes and high-intensity focused ultrasound (HIFU) enhanced antitumor effect by tumor ablation.

PubMed

Hamano, Nobuhito; Negishi, Yoichi; Takatori, Kyohei; Endo-Takahashi, Yoko; Suzuki, Ryo; Maruyama, Kazuo; Niidome, Takuro; Aramaki, Yukihiko

2014-01-01

Ultrasound (US) is used in the clinical setting not only for diagnosis but also for therapy. As a therapeutic US technique, high-intensity focused ultrasound (HIFU) can be applied to treat cancer in a clinical setting. Microbubbles increased temperature and improved the low therapeutic efficiency under HIFU; however, microbubbles have room for improvement in size, stability, and targeting ability. To solve these issues, we reported that "Bubble liposomes" (BLs) containing the US imaging gas (perfluoropropane gas) liposomes were suitable for ultrasound imaging and gene delivery. In this study, we examined whether BLs and HIFU could enhance the ablation area of the tumor and the antitumor effect. First, we histologically analyzed the tumor after BLs and HIFU. The ablation area of the treatment of BLs and HIFU was broader than that of HIFU alone. Next, we monitored the temperature of the tumor, and examined the antitumor effect. The temperature increase with BLs and HIFU treatment was faster and higher than that with HIFU alone. Moreover, treatment with BLs and HIFU enhanced the antitumor effect, which was better than with HIFU alone. Thus, the combination of BLs and HIFU could be efficacious for cancer therapy.

Bronchiectasis in Children: Current Concepts in Immunology and Microbiology.

PubMed

Pizzutto, Susan J; Hare, Kim M; Upham, John W

2017-01-01

Bronchiectasis is a complex chronic respiratory condition traditionally characterized by chronic infection, airway inflammation, and progressive decline in lung function. Early diagnosis and intensive treatment protocols can stabilize or even improve the clinical prognosis of children with bronchiectasis. However, understanding the host immunologic mechanisms that contribute to recurrent infection and prolonged inflammation has been identified as an important area of research that would contribute substantially to effective prevention strategies for children at risk of bronchiectasis. This review will focus on the current understanding of the role of the host immune response and important pathogens in the pathogenesis of bronchiectasis (not associated with cystic fibrosis) in children.

Is premium support the right medicine for Medicare?

PubMed

Oberlander, J

2000-01-01

This paper assesses the desirability of transforming Medicare into a premium-support system. I focus on three areas crucial to the future of Medicare: cost savings, beneficiary choice, and the stability of traditional Medicare. Based on my analysis of the Bipartisan Commission on the Future of Medicare plan, I find substantial problems with adopting premium support for Medicare. In particular, projections of premium-support savings are based on questionable assumptions that the slowdown in health spending during 1993-1997 can be sustained and extrapolated to future Medicare performance. Consequently, premium support may inadvertently destabilize public Medicare and erode beneficiary choice without achieving substantial savings.

Comparison of low back mobility and stability exercises from Pilates in non-specific low back pain: A study protocol of a randomized controlled trial.

PubMed

Miranda, Iã Ferreira; Souza, Catiane; Schneider, Alexandre Tavares; Chagas, Leandro Campos; Loss, Jefferson Fagundes

2018-05-01

There is some evidence in the literature about the effectiveness of the Pilates methods in the low back pain. Moreover, Pilates focus on exercises that empathizes the stability and/or mobility of the spine. Therefore, it is discussed in the literature whether higher levels of stability or mobility of the lumbar spine generates better results, both in performance and rehabilitation for low back pain. Compare the effects of the low back mobility and stability exercises from Pilates Method on low back pain, disability and movement functionality in individuals with non-specific chronic low back pain. 28 participants will be randomized into two exercise protocol from Pilates methods, one focusing on low back stability and other on low back mobility. Low back pain (visual analogic scale), low back disability (Oswestry) and movement functionality (7 functional movement tasks) will be evaluated before and after 10 sessions of Pilates exercise by the same trained assessor. A mixed designed ANOVA with two factors will be used. This study is the first to compare these outcomes for chronic low back pain participants with two exercises protocol focusing on low back mobility and stability and the results will evaluate what to prioritize with Pilates exercises to give better results for that population. Copyright © 2017 Elsevier Ltd. All rights reserved.

Silicon carbide ceramic membranes

NASA Astrophysics Data System (ADS)

Suwanmethanond, Varaporn

This dissertation focuses on the preparation of silicon carbide (SiC) ceramic membranes on SiC substrates. An original technique of SiC porous substrate preparation using sintering methods was developed during the work for the completion of the dissertation. The resulting SiC substrates have demonstrated high porosity, high internal surface area, well interconnected surface pore network and, at the same time, good thermal, chemical and mechanical stability. In a further development, sol-gel techniques were used to deposit micro-porous SiC membranes on these SiC porous substrates. The SiC membranes were characterized by a variety of techniques: ideal gas selectivity (He and N2), XRD, BET, SEM, XPS, and AFM. The characterization results confirmed that the asymmetric sol-gel SiC membranes were of high quality, with no cracks or pinholes, and exhibiting high resistance to corrosion and high hydro-thermal stability. In conclusion, the SiC ceramic membrane work was successfully completed. Two publications in international peer reviewed journals resulted out of this work.

Small Gas Turbine Combustor Primary Zone Study

NASA Technical Reports Server (NTRS)

Sullivan, R. E.; Young, E. R.; Miles, G. A.; Williams, J. R.

1983-01-01

A development process is described which consists of design, fabrication, and preliminary test evaluations of three approaches to internal aerodynamic primary zone flow patterns: (1) conventional double vortex swirl stabilization; (2) reverse flow swirl stabilization; and (3) large single vortex flow system. Each concept incorporates special design features aimed at extending the performance capability of the small engine combustor. Since inherent geometry of these combustors result in small combustion zone height and high surface area to volume ratio, design features focus on internal aerodynamics, fuel placement, and advanced cooling. The combustors are evaluated on a full scale annular combustor rig. A correlation of the primary zone performance with the overall performance is accomplished using three intrusion type gas sampling probes located at the exit of the primary zone section. Empirical and numerical methods are used for designing and predicting the performance of the three combustor concepts and their subsequent modifications. The calibration of analytical procedures with actual test results permits an updating of the analytical design techniques applicable to small reverse flow annular combustors.

Conditional random matrix ensembles and the stability of dynamical systems

NASA Astrophysics Data System (ADS)

Kirk, Paul; Rolando, Delphine M. Y.; MacLean, Adam L.; Stumpf, Michael P. H.

2015-08-01

Random matrix theory (RMT) has found applications throughout physics and applied mathematics, in subject areas as diverse as communications networks, population dynamics, neuroscience, and models of the banking system. Many of these analyses exploit elegant analytical results, particularly the circular law and its extensions. In order to apply these results, assumptions must be made about the distribution of matrix elements. Here we demonstrate that the choice of matrix distribution is crucial. In particular, adopting an unrealistic matrix distribution for the sake of analytical tractability is liable to lead to misleading conclusions. We focus on the application of RMT to the long-standing, and at times fractious, ‘diversity-stability debate’, which is concerned with establishing whether large complex systems are likely to be stable. Early work (and subsequent elaborations) brought RMT to bear on the debate by modelling the entries of a system’s Jacobian matrix as independent and identically distributed (i.i.d.) random variables. These analyses were successful in yielding general results that were not tied to any specific system, but relied upon a restrictive i.i.d. assumption. Other studies took an opposing approach, seeking to elucidate general principles of stability through the analysis of specific systems. Here we develop a statistical framework that reconciles these two contrasting approaches. We use a range of illustrative dynamical systems examples to demonstrate that: (i) stability probability cannot be summarily deduced from any single property of the system (e.g. its diversity); and (ii) our assessment of stability depends on adequately capturing the details of the systems analysed. Failing to condition on the structure of dynamical systems will skew our analysis and can, even for very small systems, result in an unnecessarily pessimistic diagnosis of their stability.

Evaluating Red Reflex and Surgeon Preference Between Nearly-Collimated and Focused Beam Microscope Illumination Systems

PubMed Central

Cionni, Robert J.; Pei, Ron; Dimalanta, Ramon; Lubeck, David

2015-01-01

Purpose To evaluate the intensity and stability of the red reflex produced by ophthalmic surgical microscopes with nearly-collimated versus focused illumination systems and to assess surgeon preference in a simulated surgical setting. Methods This two-part evaluation consisted of postproduction surgical video analysis of red reflex intensity and a microscope use and preference survey completed by 13 experienced cataract surgeons. Survey responses were based on bench testing and experience in a simulated surgical setting. A microscope with nearly-collimated beam illumination and two focused beam microscopes were assessed. Results Red reflex intensity and stability were greater with the nearly-collimated microscope illumination system. In the bench testing survey, surgeons reported that the red reflex was maintained over significantly greater distances away from pupillary center, and depth of focus was numerically greater with nearly-collimated illumination relative to focused illumination. Most participating surgeons (≥64%) reported a preference for the microscope with nearly-collimated illumination with regard to red reflex stability, depth of focus, visualization, surgical working distance, and perceived patient comfort. Conclusions The microscope with nearly-collimated illumination produced a more intense and significantly more stable red reflex and was preferred overall by more surgeons. Translational Relevance This is the first report of an attempt to quantify red reflex intensity and stability and to evaluate surgically-relevant parameters between microscope systems. The data and methods presented here may provide a basis for future studies attempting to quantify differences between surgical microscopes that may affect surgeon preference and microscope use in ophthalmic surgery. PMID:26290778

Do Crisis Response Operations Affect Political and Economic Stability?

DTIC Science & Technology

2003-05-01

military presence itself actually affects overall levels of political and economic stability is still an open question. We look at the following two...relationship between military actions and political and economic stability . In this paper, we focus only on the crisis response piece of the overseas presence issue.

Stabilization of global temperature at 1.5°C and 2.0°C: implications for coastal areas

PubMed Central

Brown, Sally; Wolff, Claudia; Merkens, Jan-Ludolf

2018-01-01

The effectiveness of stringent climate stabilization scenarios for coastal areas in terms of reduction of impacts/adaptation needs and wider policy implications has received little attention. Here we use the Warming Acidification and Sea Level Projector Earth systems model to calculate large ensembles of global sea-level rise (SLR) and ocean pH projections to 2300 for 1.5°C and 2.0°C stabilization scenarios, and a reference unmitigated RCP8.5 scenario. The potential consequences of these projections are then considered for global coastal flooding, small islands, deltas, coastal cities and coastal ecology. Under both stabilization scenarios, global mean ocean pH (and temperature) stabilize within a century. This implies significant ecosystem impacts are avoided, but detailed quantification is lacking, reflecting scientific uncertainty. By contrast, SLR is only slowed and continues to 2300 (and beyond). Hence, while coastal impacts due to SLR are reduced significantly by climate stabilization, especially after 2100, potential impacts continue to grow for centuries. SLR in 2300 under both stabilization scenarios exceeds unmitigated SLR in 2100. Therefore, adaptation remains essential in densely populated and economically important coastal areas under climate stabilization. Given the multiple adaptation steps that this will require, an adaptation pathways approach has merits for coastal areas. This article is part of the theme issue ‘The Paris Agreement: understanding the physical and social challenges for a warming world of 1.5°C above pre-industrial levels’. PMID:29610380

Stabilization of global temperature at 1.5°C and 2.0°C: implications for coastal areas.

PubMed

Nicholls, Robert J; Brown, Sally; Goodwin, Philip; Wahl, Thomas; Lowe, Jason; Solan, Martin; Godbold, Jasmin A; Haigh, Ivan D; Lincke, Daniel; Hinkel, Jochen; Wolff, Claudia; Merkens, Jan-Ludolf

2018-05-13

The effectiveness of stringent climate stabilization scenarios for coastal areas in terms of reduction of impacts/adaptation needs and wider policy implications has received little attention. Here we use the Warming Acidification and Sea Level Projector Earth systems model to calculate large ensembles of global sea-level rise (SLR) and ocean pH projections to 2300 for 1.5°C and 2.0°C stabilization scenarios, and a reference unmitigated RCP8.5 scenario. The potential consequences of these projections are then considered for global coastal flooding, small islands, deltas, coastal cities and coastal ecology. Under both stabilization scenarios, global mean ocean pH (and temperature) stabilize within a century. This implies significant ecosystem impacts are avoided, but detailed quantification is lacking, reflecting scientific uncertainty. By contrast, SLR is only slowed and continues to 2300 (and beyond). Hence, while coastal impacts due to SLR are reduced significantly by climate stabilization, especially after 2100, potential impacts continue to grow for centuries. SLR in 2300 under both stabilization scenarios exceeds unmitigated SLR in 2100. Therefore, adaptation remains essential in densely populated and economically important coastal areas under climate stabilization. Given the multiple adaptation steps that this will require, an adaptation pathways approach has merits for coastal areas.This article is part of the theme issue 'The Paris Agreement: understanding the physical and social challenges for a warming world of 1.5°C above pre-industrial levels'. © 2018 The Authors.

Stabilization of global temperature at 1.5°C and 2.0°C: implications for coastal areas

NASA Astrophysics Data System (ADS)

Nicholls, Robert J.; Brown, Sally; Goodwin, Philip; Wahl, Thomas; Lowe, Jason; Solan, Martin; Godbold, Jasmin A.; Haigh, Ivan D.; Lincke, Daniel; Hinkel, Jochen; Wolff, Claudia; Merkens, Jan-Ludolf

2018-05-01

The effectiveness of stringent climate stabilization scenarios for coastal areas in terms of reduction of impacts/adaptation needs and wider policy implications has received little attention. Here we use the Warming Acidification and Sea Level Projector Earth systems model to calculate large ensembles of global sea-level rise (SLR) and ocean pH projections to 2300 for 1.5°C and 2.0°C stabilization scenarios, and a reference unmitigated RCP8.5 scenario. The potential consequences of these projections are then considered for global coastal flooding, small islands, deltas, coastal cities and coastal ecology. Under both stabilization scenarios, global mean ocean pH (and temperature) stabilize within a century. This implies significant ecosystem impacts are avoided, but detailed quantification is lacking, reflecting scientific uncertainty. By contrast, SLR is only slowed and continues to 2300 (and beyond). Hence, while coastal impacts due to SLR are reduced significantly by climate stabilization, especially after 2100, potential impacts continue to grow for centuries. SLR in 2300 under both stabilization scenarios exceeds unmitigated SLR in 2100. Therefore, adaptation remains essential in densely populated and economically important coastal areas under climate stabilization. Given the multiple adaptation steps that this will require, an adaptation pathways approach has merits for coastal areas. This article is part of the theme issue `The Paris Agreement: understanding the physical and social challenges for a warming world of 1.5°C above pre-industrial levels'.

Guide to Rebuilding Public Sector Services in Stability Operations: A Role for the Military

DTIC Science & Technology

2009-10-01

economic growth. Each topic discussion focuses on the key issues, trade-offs faced in addressing those issues in stability operations, and recommended...top-down versus bottom-up planning. As discussed above, countries have a long-term development framework that expresses broad national strategy for...SERVICES This section discusses a relatively narrow range of issues and potential actions in rebuilding government, focusing on government’s provision

Potential slab avalanche release area identification from estimated winter terrain: a multi-scale, fuzzy logic approach

NASA Astrophysics Data System (ADS)

Veitinger, Jochen; Purves, Ross Stuart; Sovilla, Betty

2016-10-01

Avalanche hazard assessment requires a very precise estimation of the release area, which still depends, to a large extent, on expert judgement of avalanche specialists. Therefore, a new algorithm for automated identification of potential avalanche release areas was developed. It overcomes some of the limitations of previous tools, which are currently not often applied in hazard mitigation practice. By introducing a multi-scale roughness parameter, fine-scale topography and its attenuation under snow influence is captured. This allows the assessment of snow influence on terrain morphology and, consequently, potential release area size and location. The integration of a wind shelter index enables the user to define release area scenarios as a function of the prevailing wind direction or single storm events. A case study illustrates the practical usefulness of this approach for the definition of release area scenarios under varying snow cover and wind conditions. A validation with historical data demonstrated an improved estimation of avalanche release areas. Our method outperforms a slope-based approach, in particular for more frequent avalanches; however, the application of the algorithm as a forecasting tool remains limited, as snowpack stability is not integrated. Future research activity should therefore focus on the coupling of the algorithm with snowpack conditions.

Avoiding Praetorian Societies: Focusing U.S. Strategy on Political Development

DTIC Science & Technology

2014-03-01

the centrality of political development, understand the critical role of input institutions in political stability , and make efforts to foster these institutions in stability and reconstruction operations.

On precise phase difference measurement approach using border stability of detection resolution.

PubMed

Bai, Lina; Su, Xin; Zhou, Wei; Ou, Xiaojuan

2015-01-01

For the precise phase difference measurement, this paper develops an improved dual phase coincidence detection method. The measurement resolution of the digital phase coincidence detection circuits is always limited, for example, only at the nanosecond level. This paper reveals a new way to improve the phase difference measurement precision by using the border stability of the circuit detection fuzzy areas. When a common oscillator signal is used to detect the phase coincidence with the two comparison signals, there will be two detection fuzzy areas for the reason of finite detection resolution surrounding the strict phase coincidence. Border stability of fuzzy areas and the fluctuation difference of the two fuzzy areas can be even finer than the picoseconds level. It is shown that the system resolution obtained only depends on the stability of the circuit measurement resolution which is much better than the measurement device resolution itself.

Stability issues pertaining large area perovskite and dye-sensitized solar cells and modules

NASA Astrophysics Data System (ADS)

Castro-Hermosa, S.; Yadav, S. K.; Vesce, L.; Guidobaldi, A.; Reale, A.; Di Carlo, A.; Brown, T. M.

2017-01-01

Perovskite and dye-sensitized solar cells are PV technologies which hold promise for PV application. Arguably, the biggest issue facing these technologies is stability. The vast majority of studies have been limited to small area laboratory cells. Moisture, oxygen, UV light, thermal and electrical stresses are leading the degradation causes. There remains a shortage of stability investigations on large area devices, in particular modules. At the module level there exist particular challenges which can be different from those at the small cell level such as encapsulation (not only of the unit cells but of interconnections and contacts), non-uniformity of the layer stacks and unit cells, reverse bias stresses, which are important to investigate for technologies that aim for industrial acceptance. Herein we present a review of stability investigations published in the literature pertaining large area perovskite and dye-sensitized solar devices fabricated both on rigid (glass) and flexible substrates.

Interaction of Boron Clusters with Oxygen: a DFT Study

NASA Astrophysics Data System (ADS)

Salavitabar, Kamron; Boggavarapu, Kiran; Kandalam, Anil

A controlled combustion involving aluminum nanoparticles has often been the focus of studies in the field of solid fuel propellants. However very little focus has been given to the study of boron nanoparticles in controlled combustion. In contrast to aluminum nanoclusters, boron nanoclusters (Bn) are known to exhibit a planar geometries even at the size of n = 19 - 20, and thus offer a greater surface area for interaction with oxygen. Earlier experimental studies have shown that boron nanoclusters exhibit different reactivity with oxygen depending on their size and charge. In this poster, we present our recent density functional theory based results, focusing on the reactivity patterns of neutral and negatively charged B5 cluster with On, where n = 1 - 5; and B6 cluster with On (n = 1 - 2). The effect of charge on the reactivity of boron cluster, variation in the stability of product clusters, i e., neutral and negatively charged B5On (n = 1 - 5) and B6On (n = 1 - 2) are also examined. Financial Support from West Chester University Foundation under FaStR grant is acknowledged.

Space shuttle maneuvering engine reusable thrust chamber program. Task 11: Low Epsilon stability test plan

NASA Technical Reports Server (NTRS)

Pauckert, R. P.

1974-01-01

The performance and heat transfer characteristics of a doublet element type injector for the space shuttle orbiter maneuvering engine thrust chamber were investigated. Ths stability characteristics were evaluated over a range of chamber pressures and mixture ratios. The specific objectives of the test were: (1) to determine whether stability has been influenced by injection of boundary layer coolant across the cavity entrance, (2) if the injector is stable, to determine the minimum cavity area required to maintain stability, and (3) if the injector is unstable, to determine the effects of entrance geometry and increased area on stability.

Stability comparison between commercially available mini-implants and a novel design: part 1.

PubMed

Hong, Christine; Lee, Haofu; Webster, Richard; Kwak, Jinny; Wu, Benjamin M; Moon, Won

2011-07-01

To compare mechanical stability among five mini-implant designs--a newly invented design and four commercially available designs that vary by shape and threading; to calculate external surface area of each design using high-resolution micro-computed tomography; and to evaluate the relationship between surface area and stability results. The four commercially available mini-implants--single-threaded and cylindrical (SC), single-threaded and tapered (ST), double-threaded and cylindrical (DC), double-threaded and tapered (DT)--and a new implant that is designed to engage mostly in cortical bone with shorter and wider dimensions (N1) were inserted in simulated bone with cortical and trabecular bone layers. The mechanical study consisted of torque measurements and lateral displacement tests. External surface area was computed using a 25-µm micro-CT. Maximum insertion torque, maximum removal torque, and force levels for displacements were the highest in N1, followed by DT, ST, DC, and SC (α  =  .05). The surface area was largest in DT, followed by N1, ST, DC, and SC. Surface area engaged in cortical bone, however, was the greatest in N1. The surface area of mini-implants had positive correlation with stability. Among commercial designs, both added tapering and double threading improved stability. N1 was the most stable design within this research design. The new design has the potential to be clinically superior; it has enhanced stability and there is diminished risk of endangering nearby anatomic structures during placement and orthodontic treatment, but the design requires refinements to reduce insertion torque to avoid clinical difficulty and patient discomfort.

Recent slope failures in the Dolomites (Northeastern Italian Alps) in a context of climate change

NASA Astrophysics Data System (ADS)

Chiarle, Marta; Paranunzio, Roberta; Laio, Francesco; Nigrelli, Guido; Guzzetti, Fausto

2014-05-01

Climate change in the Greater Alpine Region is seriously affecting permafrost distribution, with relevant consequences on slope stability. In the Italian Alps, the number of failures from rockwalls at high elevation markedly increased in the last 20-30 years: the consistent temperature increase, which warmed twice than the global average, may have seriously influenced slope stability, in terms of glaciers retreat and permafrost degradation. Moreover, the growing number of tourists and activities in alpine regions (in particular in the Dolomites) made these areas particularly critical in relation to natural hazards. In this light, an integrated short-term geomorphological and climatic analysis was performed, in order to better comprehend the impact of main climate elements (especially temperature and precipitation) on slope failures in high mountain areas. In this contribution, we focus on three recent slope failures occurred at high elevation sites in the Dolomites (Northeastern Italian Alps), declared a UNESCO World Heritage Site in August 2009. We describe here three important rock falls occurred in the autumn 2013: 1) the Sorapiss rock fall, on 30 September 2013; 2) the Monte Civetta rock fall, on 16 November 2013; 3) the Monte Antelao rock fall, on 22 November 2013. The Monte Civetta rock fall damaged some climbing routes, while the other two landslides did not cause any damage or injury. Despite the limited volume involved, these three events represent an important warning sign in the context of ongoing climate change. Geomorphological information about the rock fall sites were combined with the climatic data acquired from the meteorological stations surrounding the slope failure areas. A short-term climatic analysis was performed, with the aim of understanding the role of the main climatic elements in the triggering of natural instability events in this area and in the Alps in general.

Mental training enhances attentional stability: Neural and behavioral evidence

PubMed Central

Lutz, Antoine; Slagter, Heleen A.; Rawlings, Nancy B.; Francis, Andrew D.; Greischar, Lawrence L.; Davidson, Richard J.

2009-01-01

The capacity to stabilize the content of attention over time varies among individuals and its impairment is a hallmark of several mental illnesses. Impairments in sustained attention in patients with attention disorders have been associated with increased trial-to-trial variability in reaction time and event-related potential (ERP) deficits during attention tasks. At present, it is unclear whether the ability to sustain attention and its underlying brain circuitry are transformable through training. Here, we show, with dichotic listening task performance and electroencephalography (EEG), that training attention, as cultivated by meditation, can improve the ability to sustain attention. Three months of intensive meditation training reduced variability in attentional processing of target tones, as indicated by both enhanced theta-band phase consistency of oscillatory neural responses over anterior brain areas and reduced reaction time variability. Furthermore, those individuals who showed the greatest increase in neural response consistency showed the largest decrease in behavioral response variability. Notably, we also observed reduced variability in neural processing, in particular in low-frequency bands, regardless of whether the deviant tone was attended or unattended. Focused attention meditation may thus affect both distracter and target processing, perhaps by enhancing entrainment of neuronal oscillations to sensory input rhythms; a mechanism important for controlling the content of attention. These novel findings highlight the mechanisms underlying focused attention meditation, and support the notion that mental training can significantly affect attention and brain function. PMID:19846729

Synthesis, functionalization, and applications of metal-organic frameworks in biomedicine.

PubMed

Chen, Wei; Wu, Chunsheng

2018-02-13

Metal-organic frameworks (MOFs), also known as coordination polymers, have attracted extensive research interest in the past few decades due to their unique physical structures and potentially vast applications. In this review, we outline the recent progress in the synthesis, functionalization and applications of MOFs in biomedicine, mainly focusing on two promising, yet challenging areas, i.e., drug delivery and biosensing applications. A major challenge is the proper functionalization of MOFs with demanding properties suitable for biomedical applications. Extensive studies on MOFs in biomedicine have led to substantial progress in the control of key properties of MOFs such as toxicity, size and shape, and biological stability. Due to their flexible composition, pore size and easy functionalization properties, MOFs can be utilized as key components for the development of various functional systems, and their applications in drug delivery and biosensing are reviewed. Future trends and perspectives in these research areas are also outlined.

Luminescence properties of femtosecond-laser-activated silver oxide nanoparticles embedded in a biopolymer matrix

NASA Astrophysics Data System (ADS)

Gleitsmann, T.; Bernhardt, T. M.; Wöste, L.

2006-01-01

Strong visible luminescence is observed from silver clusters generated by femtosecond-laser-induced reduction of silver oxide nanoparticles embedded in a polymeric gelatin matrix. Light emission from the femtosecond-laser-activated matrix areas considerably exceeds the luminescence intensity of similarly activated bare silver oxide nanoparticle films. Optical spectroscopy of the activated polymer films supports the assignment of the emissive properties to the formation of small silver clusters under focused femtosecond-laser irradiation. The size of the photogenerated clusters is found to sensitively depend on the laser exposure time, eventually leading to the formation of areas of metallic silver in the biopolymer matrix. In this case, luminescence can still be observed in the periphery of the metallic silver structures, emphasizing the importance of the organic matrix for the stabilization of the luminescent nanocluster structures at the metal matrix interface.

Effects of Task and Category Membership on Representation Stability

ERIC Educational Resources Information Center

Gaillard, Audrey; Urdapilleta, Isabel; Houix, Olivier; Manetta, Celine

2011-01-01

This study examined the within-subject stability of 150 participants who performed both a sorting task and a property-generation task over multiple sessions, focusing on three concrete concept categories (food, animals and bathroom products). We hypothesized that (1) the within-subject stability would be higher in the sorting task than in the…

Temporal and spatial distribution characteristics in the natural plague foci of Chinese Mongolian gerbils based on spatial autocorrelation.

PubMed

Du, Hai-Wen; Wang, Yong; Zhuang, Da-Fang; Jiang, Xiao-San

2017-08-07

The nest flea index of Meriones unguiculatus is a critical indicator for the prevention and control of plague, which can be used not only to detect the spatial and temporal distributions of Meriones unguiculatus, but also to reveal its cluster rule. This research detected the temporal and spatial distribution characteristics of the plague natural foci of Mongolian gerbils by body flea index from 2005 to 2014, in order to predict plague outbreaks. Global spatial autocorrelation was used to describe the entire spatial distribution pattern of the body flea index in the natural plague foci of typical Chinese Mongolian gerbils. Cluster and outlier analysis and hot spot analysis were also used to detect the intensity of clusters based on geographic information system methods. The quantity of M. unguiculatus nest fleas in the sentinel surveillance sites from 2005 to 2014 and host density data of the study area from 2005 to 2010 used in this study were provided by Chinese Center for Disease Control and Prevention. The epidemic focus regions of the Mongolian gerbils remain the same as the hot spot regions relating to the body flea index. High clustering areas possess a similar pattern as the distribution pattern of the body flea index indicating that the transmission risk of plague is relatively high. In terms of time series, the area of the epidemic focus gradually increased from 2005 to 2007, declined rapidly in 2008 and 2009, and then decreased slowly and began trending towards stability from 2009 to 2014. For the spatial change, the epidemic focus regions began moving northward from the southwest epidemic focus of the Mongolian gerbils from 2005 to 2007, and then moved from north to south in 2007 and 2008. The body flea index of Chinese gerbil foci reveals significant spatial and temporal aggregation characteristics through the employing of spatial autocorrelation. The diversity of temporary and spatial distribution is mainly affected by seasonal variation, the human activity and natural factors.

Scale dependence of the diversity–stability relationship in a temperate grassland

PubMed Central

Zhang, Yunhai; He, Nianpeng; Loreau, Michel; Pan, Qingmin; Han, Xingguo

2018-01-01

A positive relationship between biodiversity and ecosystem stability has been reported in many ecosystems; however, it has yet to be determined whether and how spatial scale affects this relationship. Here, for the first time, we assessed the effects of alpha, beta and gamma diversity on ecosystem stability and the scale dependence of the slope of the diversity–stability relationship.By employing a long-term (33 years) dataset from a temperate grassland, northern China, we calculated the all possible spatial scales with the complete combination from the basic 1-m2 plots.Species richness was positively associated with ecosystem stability through species asynchrony and overyielding at all spatial scales (1, 2, 3, 4 and 5 m2). Both alpha and beta diversity were positively associated with gamma stability.Moreover, the slope of the diversity–area relationship was significantly higher than that of the stability–area relationship, resulting in a decline of the slope of the diversity–stability relationship with increasing area.Synthesis. With the positive species diversity effect on ecosystem stability from small to large spatial scales, our findings demonstrate the need to maintain a high biodiversity and biotic heterogeneity as insurance against the risks incurred by ecosystems in the face of global environmental changes. PMID:29725139

The effects of isolated and integrated 'core stability' training on athletic performance measures: a systematic review.

PubMed

Reed, Casey A; Ford, Kevin R; Myer, Gregory D; Hewett, Timothy E

2012-08-01

Core stability training, operationally defined as training focused to improve trunk and hip control, is an integral part of athletic development, yet little is known about its direct relation to athletic performance. This systematic review focuses on identification of the association between core stability and sports-related performance measures. A secondary objective was to identify difficulties encountered when trying to train core stability with the goal of improving athletic performance. A systematic search was employed to capture all articles related to athletic performance and core stability training that were identified using the electronic databases MEDLINE, CINAHL and SPORTDiscus™ (1982-June 2011). A systematic approach was used to evaluate 179 articles identified for initial review. Studies that performed an intervention targeted toward the core and measured an outcome related to athletic or sport performances were included, while studies with a participant population aged 65 years or older were excluded. Twenty-four in total met the inclusionary criteria for review. Studies were evaluated using the Physical Therapy Evidence Database (PEDro) scale. The 24 articles were separated into three groups, general performance (n = 8), lower extremity (n = 10) and upper extremity (n = 6), for ease of discussion. In the majority of studies, core stability training was utilized in conjunction with more comprehensive exercise programmes. As such, many studies saw improvements in skills of general strengths such as maximum squat load and vertical leap. Surprisingly, not all studies reported measurable increases in specific core strength and stability measures following training. Additionally, investigations that targeted the core as the primary goal for improved outcome of training had mixed results. Core stability is rarely the sole component of an athletic development programme, making it difficult to directly isolate its affect on athletic performance. The population biases of some studies of athletic performance also confound the results. Targeted core stability training provides marginal benefits to athletic performance. Conflicting findings and the lack of a standardization for measurement of outcomes and training focused to improve core strength and stability pose difficulties. Because of this, further research targeted to determine this relationship is necessary to better understand how core strength and stability affect athletic performance.

Compression and contact area of anterior strut grafts in spinal instrumentation: a biomechanical study.

PubMed

Pizanis, Antonius; Holstein, Jörg H; Vossen, Felix; Burkhardt, Markus; Pohlemann, Tim

2013-08-26

Anterior bone grafts are used as struts to reconstruct the anterior column of the spine in kyphosis or following injury. An incomplete fusion can lead to later correction losses and compromise further healing. Despite the different stabilizing techniques that have evolved, from posterior or anterior fixating implants to combined anterior/posterior instrumentation, graft pseudarthrosis rates remain an important concern. Furthermore, the need for additional anterior implant fixation is still controversial. In this bench-top study, we focused on the graft-bone interface under various conditions, using two simulated spinal injury models and common surgical fixation techniques to investigate the effect of implant-mediated compression and contact on the anterior graft. Calf spines were stabilised with posterior internal fixators. The wooden blocks as substitutes for strut grafts were impacted using a "pressfit" technique and pressure-sensitive films placed at the interface between the vertebral bone and the graft to record the compression force and the contact area with various stabilization techniques. Compression was achieved either with posterior internal fixator alone or with an additional anterior implant. The importance of concomitant ligament damage was also considered using two simulated injury models: pure compression Magerl/AO fracture type A or rotation/translation fracture type C models. In type A injury models, 1 mm-oversized grafts for impaction grafting provided good compression and fair contact areas that were both markedly increased by the use of additional compressing anterior rods or by shortening the posterior fixator construct. Anterior instrumentation by itself had similar effects. For type C injuries, dramatic differences were observed between the techniques, as there was a net decrease in compression and an inadequate contact on the graft occurred in this model. Under these circumstances, both compression and the contact area on graft could only be maintained at high levels with the use of additional anterior rods. Under experimental conditions, we observed that ligamentous injury following type C fracture has a negative influence on the compression and contact area of anterior interbody bone grafts when only an internal fixator is used for stabilization. Because of the loss of tension banding effects in type C injuries, an additional anterior compressing implant can be beneficial to restore both compression to and contact on the strut graft.

Study on the Influence of Elevation of Tailing Dam on Stability

NASA Astrophysics Data System (ADS)

Wan, Shuai; Wang, Kun; Kong, Songtao; Zhao, Runan; Lan, Ying; Zhang, Run

2017-12-01

This paper takes Yunnan as the object of a tailing, by theoretical analysis and numerical calculation method of the effect of seismic load effect of elevation on the stability of the tailing, to analyse the stability of two point driven safety factor and liquefaction area. The Bishop method is adopted to simplify the calculation of dynamic safety factor and liquefaction area analysis using comparison method of shear stress to analyse liquefaction, so we obtained the influence of elevation on the stability of the tailing. Under the earthquake, with the elevation increased, the safety coefficient of dam body decreases, shallow tailing are susceptible to liquefy. Liquefaction area mainly concentrated in the bank below the water surface, to improve the scientific basis for the design and safety management of the tailing.

STABILITY OF A CABLE-MOORED AIRSHIP

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bennett, M.D.

1959-03-01

Equations of motion for the longitudinal and directional stability of a cable-moored airship were analyzed on an analog computer by subjecting the configuration to a horizontals ramp-type gust and observing the induced motion. The results indicate that the proposed configuration is dynamically stable (overdamped, essentially), and that it possesses a sufficiently high degree of stability to permit a 20-percent reduction in the fin planform area governing stability in the longitudinal direction. However, this reduction cannot be accomplished by decreasing the appropriate area of the proposed three-fintail because such a decrease causes the airship to become directionally unstable. Aerodynamically, the desiredmore » area reduction can best be effected by the use of a four-fin tail. Motions are calculated for various modifications to the proposed configuration. (auth)« less

The downside of goal-focused leadership: the role of personality in subordinate exhaustion.

PubMed

Perry, Sara Jansen; Witt, L A; Penney, Lisa M; Atwater, Leanne

2010-11-01

Exhaustion has a significant impact on employees and organizations, and leader behavior may affect it. We applied conservation of resources theory to test propositions regarding the joint effects of goal-focused leadership (GFL) and personality on employee exhaustion. We proposed that the relationship between GFL and exhaustion depends on employees' standing on both conscientiousness and emotional stability. Specifically, we expected that high-conscientiousness subordinates experience greater compatibility with a goal-focused leader because of their predisposition to direct resources toward achievement and goal setting, resulting in lower exhaustion under such a leader than among low-conscientiousness employees. Furthermore, high emotional stability may compensate for GFL incompatibility among low-conscientiousness employees by providing additional resources to manage GFL. In contrast, employees low on both traits likely experience greater exhaustion under a goal-focused leader compared with other employees. Results revealed a 3-way interaction in 2 independent samples and were generally supportive of our predictions. GFL was associated with heightened exhaustion among individuals in the low-emotional-stability, low-conscientiousness group but not among workers having any other trait combination. (c) 2010 APA, all rights reserved.

Long-term monitoring of stream bank stability under different vegetation cover

NASA Astrophysics Data System (ADS)

Krzeminska, Dominika; Skaalsveen, Kamilla; Kerkhof, Tjibbe

2017-04-01

Vegetated buffer zones are common environmental measures in many countries, including Norway. The presence of riparian vegetation on stream banks not only provides ecological benefits but also influence bank slope stability, through several complex interactions between riparian vegetation and hydro - mechanical processes. The hydrological processes associated with slope stability are complex and yet difficult to quantify, especially because their transient effects (e.g. changes throughout the vegetation life cycle). Additionally, there is very limited amount of field scale research focusing on investigation of coupled hydrological and mechanical influence of vegetation on stream bank behavior, accounting for both seasonal time scale and different vegetation type, and none dedicated to marine clay soils (typically soil for Norway). In order to fill this gap we established continues, long term hydrogeological monitoring o selected cross - section within stream bank, covered with different types of vegetation, typical for Norwegian agriculture areas (grass, shrubs, and trees). The monitoring involves methods such as spatial and temporal monitoring of soil moisture conditions, ground water level and fluctuation of water level in the stream. Herein we will present first 10 months of monitoring data: observed hydrological trends and differences between three cross - sections. Moreover, we will present first modelling exercises that aims to estimate stream banks stability with accounting on presence of different vegetation types using BSTEM and HYDRUS models. With this presentation, we would like to stimulate the discussion and get feedback that could help us to improve both, our experimental set up and analysis approach.

Development and genetics of brain temporal stability related to attention problems in adolescent twins.

PubMed

Smit, Dirk J A; Anokhin, Andrey P

2017-05-01

The brain continuously develops and reorganizes to support an expanding repertoire of behaviors and increasingly complex cognition. These processes may, however, also result in the appearance or disappearance of specific neurodevelopmental disorders such as attention problems. To investigate whether brain activity changed during adolescence, how genetics shape this change, and how these changes were related to attention problems, we measured EEG activity in 759 twins and siblings, assessed longitudinally in four waves (12, 14, 16, and 18years of age). Attention problems were assessed with the SWAN at waves 12, 14, and 16. To characterize functional brain development, we used a measure of temporal stability (TS) of brain oscillations over the recording time of 5min reflecting the tendency of a brain to maintain the same oscillatory state for longer or shorter periods. Increased TS may reflect the brain's tendency to maintain stability, achieve focused attention, and thus reduce "mind wandering" and attention problems. The results indicate that brain TS is increased across the scalp from 12 to 18. TS showed large individual differences that were heritable. Change in TS (alpha oscillations) was heritable between 12 and 14 and between 14 and 16 for the frontal brain areas. Absolute levels of brain TS at each wave were positively correlated with attention problems but not significantly. High and low attention problems subjects showed different developmental trajectories in TS, which was significant in a cluster of frontal leads. These results indicate that trajectories in brain TS development are a biomarker for the developing brain. TS in brain oscillations is highly heritable, and age-related change in TS is also heritable in selected brain areas. These results suggest that high and low attention problems subjects are at different stages of brain development. Copyright © 2016. Published by Elsevier B.V.

San Francisquito Creek Stabilization at Bonde Weir Project

EPA Pesticide Factsheets

Information about the SFBWQP San Francisquito Creek Stabilization at Bonde Weir Project, part of an EPA competitive grant program to improve SF Bay water quality focused on restoring impaired waters and enhancing aquatic resources.

Signal Processing Methods for Liquid Rocket Engine Combustion Spontaneous Stability and Rough Combustion Assessments

NASA Technical Reports Server (NTRS)

Kenny, R. Jeremy; Casiano, Matthew; Fischbach, Sean; Hulka, James R.

2012-01-01

Liquid rocket engine combustion stability assessments are traditionally broken into three categories: dynamic stability, spontaneous stability, and rough combustion. This work focuses on comparing the spontaneous stability and rough combustion assessments for several liquid engine programs. The techniques used are those developed at Marshall Space Flight Center (MSFC) for the J-2X Workhorse Gas Generator program. Stability assessment data from the Integrated Powerhead Demonstrator (IPD), FASTRAC, and Common Extensible Cryogenic Engine (CECE) programs are compared against previously processed J-2X Gas Generator data. Prior metrics for spontaneous stability assessments are updated based on the compilation of all data sets.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Potomkin, Mykhailo; Kaiser, Andreas; Berlyand, Leonid

We consider active particles swimming in a convergent fluid flow in a trapezoid nozzle with no-slip walls. We use mathematical modeling to analyze trajectories of these particles inside the nozzle. By extensive Monte Carlo simulations, we show that trajectories are strongly affected by the background fluid flow and geometry of the nozzle leading to wall accumulation and upstream motion (rheotaxis). In particular, we describe the non-trivial focusing of active rods depending on physical and geometrical parameters. It is also established that the convergent component of the background flow leads to stability of both downstream and upstream swimming at the centerline.more » The stability of downstream swimming enhances focusing, and the stability of upstream swimming enables rheotaxis in the bulk.« less

Protein stability: a crystallographer’s perspective

PubMed Central

Deller, Marc C.; Kong, Leopold; Rupp, Bernhard

2016-01-01

Protein stability is a topic of major interest for the biotechnology, pharmaceutical and food industries, in addition to being a daily consideration for academic researchers studying proteins. An understanding of protein stability is essential for optimizing the expression, purification, formulation, storage and structural studies of proteins. In this review, discussion will focus on factors affecting protein stability, on a somewhat practical level, particularly from the view of a protein crystallographer. The differences between protein conformational stability and protein compositional stability will be discussed, along with a brief introduction to key methods useful for analyzing protein stability. Finally, tactics for addressing protein-stability issues during protein expression, purification and crystallization will be discussed. PMID:26841758

Relationships Between Emotional Stability, Psychosocial Mentoring Support and Career Resilience

PubMed Central

Arora, Ridhi; Rangnekar, Santosh

2015-01-01

This study empirically investigates the mediating role of psychosocial mentoring support on emotional stability personality disposition and career resilience relationship. In addition, this research also focuses on estimating the interrelationship between emotional stability, psychosocial mentoring support and career resilience. The results show substantive direct relations between emotional stability and psychosocial mentoring as well as between emotional stability and career resilience. Psychosocial mentoring is also seen as a significant predictor of career resilience. Further, it mediates partially the relationship between emotional stability personality and career resilience. Future and practical implications of research have also been provided. PMID:27247639

Computational mechanics research and support for aerodynamics and hydraulics at TFHRC. Quarterly report January through March 2011. Year 1 Quarter 2 progress report.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lottes, S. A.; Kulak, R. F.; Bojanowski, C.

2011-05-19

This project was established with a new interagency agreement between the Department of Energy and the Department of Transportation to provide collaborative research, development, and benchmarking of advanced three-dimensional computational mechanics analysis methods to the aerodynamics and hydraulics laboratories at the Turner-Fairbank Highway Research Center for a period of five years, beginning in October 2010. The analysis methods employ well-benchmarked and supported commercial computational mechanics software. Computational mechanics encompasses the areas of Computational Fluid Dynamics (CFD), Computational Wind Engineering (CWE), Computational Structural Mechanics (CSM), and Computational Multiphysics Mechanics (CMM) applied in Fluid-Structure Interaction (FSI) problems. The major areas of focusmore » of the project are wind and water loads on bridges - superstructure, deck, cables, and substructure (including soil), primarily during storms and flood events - and the risks that these loads pose to structural failure. For flood events at bridges, another major focus of the work is assessment of the risk to bridges caused by scour of stream and riverbed material away from the foundations of a bridge. Other areas of current research include modeling of flow through culverts to assess them for fish passage, modeling of the salt spray transport into bridge girders to address suitability of using weathering steel in bridges, vehicle stability under high wind loading, and the use of electromagnetic shock absorbers to improve vehicle stability under high wind conditions. This quarterly report documents technical progress on the project tasks for the period of January through March 2011.« less

The emerging dental workforce: short-term expectations of, and influences on dental students graduating from a London dental school in 2005.

PubMed

Gallagher, Jennifer E; Clarke, Wendy; Wilson, Nairn H F

2008-07-01

The aim of this research was to identify short-term career aspirations and goals of final-year dental students at a London dental school and the perceived factors that influenced these aspirations. Two methods were used to collect data on final-year students' short-term career plans and influences. Qualitative data were collected through focus groups and analysed using 'framework methodology'. These findings informed a questionnaire survey of all students at the end of their final undergraduate year. Data were entered into and analysed using a statistical software package. Thirty-five students participated in focus groups, with recruitment continuing until data were saturated. Ninety per cent (n=126) of the total population (140) responded to the questionnaire survey; the majority were Asian (70%), female (58%), and aged 23 years (59%). Short-term professional expectations focused around 'achieving professional status within a social context', 'gaining professional experience', 'developing independence' and 'achieving financial stability'. 'Achieving financial stability' was ranked as the most important influence in decision-making about their career in the short term (77%), followed by 'balance of work and other aspects of life' (75%) and 'good lifestyle' (75%). Four out of ten intended to work towards membership of a Royal College and/or becoming a specialist. Proximity to family (81%) and friends (79%) was an important or very important influence on location in the short term. Asian students were significantly more likely to rate 'proximity to family' (p=0.042), working in an 'urban area' (p=0.001) and 'opportunities for private care' (p=0.043) of greater importance than their White counterparts. Short-term aspirations involve 'achieving professional status within a social context', and personal, social, professional and financial goals. Location of future practice was significantly associated with ethnicity.

Floodplain sedimentology and sediment accumulation assessment – Savannah River Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yeager, Kevin M.

2016-01-03

The primary goal of the larger research program, of which this work is one component, is to restore the hydrodynamics and energy gradients of targeted Savannah River Site (SRS) streams to a condition comparable to local natural streams or rivers of similar order, and to stabilize sediment transport (net degradation/aggregation) with the assumption that the faunal components of these systems will quickly recover on their own (e.g., Pen Branch; Lakly and McArthur, 2000). This work is specifically focused on the identification of near-stream floodplain areas that exhibit sediment deposition or erosion, and the quantification of these processes over a historicalmore » time scale (last ~100 years).« less

Attachment theory: progress and future directions.

PubMed

Fearon, R M Pasco; Roisman, Glenn I

2017-06-01

Attachment is a key subfield in the area of parenting and parent-child relationships research. In this brief overview, we summarise what we consider to be the state-of-the-art of attachment research, focusing primarily on the nature and significance of attachment in infancy and early childhood. We review 4 major topics that are central issues in the scientific literature on attachment: (1) the role of the environment in the development of attachment, (2) the intergenerational transmission of patterns of attachment, (3) the stability of attachment patterns through early adulthood, and (4) the role of attachment in adjustment and maladjustment. We conclude by highlighting several critical unresolved issues and priorities for future research. Copyright © 2017. Published by Elsevier Ltd.

Proceedings of the 15th International Symposium on Shock Waves and Shock Tubes

NASA Astrophysics Data System (ADS)

Bershader, Daniel; Hanson, Ronald

1986-09-01

One hundred ten papers were presented in 32 sessions. Topics included: The application of Hook-method spectroscopy to the diagnosis of shock-heated gases. The nonintrusive destruction of kidney stones by underwater focused shock waves. Several of the papers reflect the recent and continuing interest in shock wave phenomena in dusty gases and other multiphase and heterogeneous systems, including chemically reactive configurations. The major subject areas were: shock propagation and interactions; shock-general chemical kinetics; shock computation, modeling, and stability problems; shock wave aerodynamics; experimental methods; shocks in multiphase and heterogeneous media; high energy gas excitation and wave phenomena; and technical applications and shocks in condensed matter.

Stockpiling hydrated lime-soil mixtures.

DOT National Transportation Integrated Search

2007-06-01

The concept and feasibility of stockpiling and reusing hydrated lime-soil mixtures to stabilize particular areas on stabilization projects after the mixing contractor has departed were examined. In chemical stabilization of subgrades, situations ofte...

Exploratory Studies in Generalized Predictive Control for Active Aeroelastic Control of Tiltrotor Aircraft

NASA Technical Reports Server (NTRS)

Kvaternik, Raymond G.; Juang, Jer-Nan; Bennett, Richard L.

2000-01-01

The Aeroelasticity Branch at NASA Langley Research Center has a long and substantive history of tiltrotor aeroelastic research. That research has included a broad range of experimental investigations in the Langley Transonic Dynamics Tunnel (TDT) using a variety of scale models and the development of essential analyses. Since 1994, the tiltrotor research program has been using a 1/5-scale, semispan aeroelastic model of the V-22 designed and built by Bell Helicopter Textron Inc. (BHTI) in 1981. That model has been refurbished to form a tiltrotor research testbed called the Wing and Rotor Aeroelastic Test System (WRATS) for use in the TDT. In collaboration with BHTI, studies under the current tiltrotor research program are focused on aeroelastic technology areas having the potential for enhancing the commercial and military viability of tiltrotor aircraft. Among the areas being addressed, considerable emphasis is being directed to the evaluation of modern adaptive multi-input multi- output (MIMO) control techniques for active stability augmentation and vibration control of tiltrotor aircraft. As part of this investigation, a predictive control technique known as Generalized Predictive Control (GPC) is being studied to assess its potential for actively controlling the swashplate of tiltrotor aircraft to enhance aeroelastic stability in both helicopter and airplane modes of flight. This paper summarizes the exploratory numerical and experimental studies that were conducted as part of that investigation.

Turbojet-exhaust-nozzle secondary-airflow pumping as an exit control of an inlet-stability bypass system for a Mach 2.5 axisymmetric mixed-compression inlet. [Lewis 10- by 10-ft. supersonic wind tunnel test

NASA Technical Reports Server (NTRS)

Sanders, B. W.

1980-01-01

The throat of a Mach 2.5 inlet that was attached to a turbojet engine was fitted with large, porous bleed areas to provide a stability bypass system that would allow a large, stable airflow range. Exhaust-nozzle, secondary-airflow pumping was used as the exit control for the stability bypass airflow. Propulsion system response and stability bypass performance were obtained for several transient airflow disturbances, both internal and external. Internal airflow disturbances included reductions in overboard bypass airflow, power lever angle, and primary-nozzle area, as well as compressor stall. Nozzle secondary pumping as a stability bypass exit control can provide the inlet with a large stability margin with no adverse effects on propulsion system performance.

Stability of organic solar cells: challenges and strategies.

PubMed

Cheng, Pei; Zhan, Xiaowei

2016-05-03

Organic solar cells (OSCs) present some advantages, such as simple preparation, light weight, low cost and large-area flexible fabrication, and have attracted much attention in recent years. Although the power conversion efficiencies have exceeded 10%, the inferior device stability still remains a great challenge. In this review, we summarize the factors limiting the stability of OSCs, such as metastable morphology, diffusion of electrodes and buffer layers, oxygen and water, irradiation, heating and mechanical stress, and survey recent progress in strategies to increase the stability of OSCs, such as material design, device engineering of active layers, employing inverted geometry, optimizing buffer layers, using stable electrodes and encapsulation. Some research areas of device stability that may deserve further attention are also discussed to help readers understand the challenges and opportunities in achieving high efficiency and high stability of OSCs towards future industrial manufacture.

Stability Design and Response to Waves by Batoids.

PubMed

Fish, Frank E; Hoffman, Jessica L

2015-10-01

Unsteady flows in the marine environment can affect the stability and locomotor costs of animals. For fish swimming at shallow depths, waves represent a form of unsteady flow. Waves consist of cyclic oscillations, during which the water moves in circular or elliptical orbits. Large gravity waves have the potential to displace fish both cyclically and in the direction of wave celerity for animals floating in the water column or holding station on the bottom. Displacement of a fish can exceed its stability control capability when the size of the wave orbit is equivalent to the size of the fish. Previous research into compensatory behaviors of fishes to waves has focused on pelagic osteichthyan fishes with laterally compressed bodies. However, dorsoventrally compressed batoid rays must also contend with waves. Examination of rays subjected to waves showed differing strategies for stability between pelagic and demersal species. Pelagic cownose rays (Rhinoptera bonasus) would glide through or be transported by waves, maintaining a positive dihedral of the wing-like pectoral fins. Demersal Atlantic stingrays (Dasyatis sabina) and freshwater rays (Potamotrygon motoro) maintained contact with the bottom and performed compensatory fin motions and body postures. The ability to limit displacement due to wave action by the demersal rays was also a function of the bottom texture. The ability of rays to maintain stability due to wave action suggests mechanisms to compensate for the velocity flux of the water impinging on the large projected area of the enlarged pectoral fins of rays. © The Author 2015. Published by Oxford University Press on behalf of the Society for Integrative and Comparative Biology. All rights reserved. For permissions please email: journals.permissions@oup.com.

Preservation of Biospecimens at Ambient Temperature: Special Focus on Nucleic Acids and Opportunities for the Biobanking Community.

PubMed

Muller, Rolf; Betsou, Fay; Barnes, Michael G; Harding, Keith; Bonnet, Jacques; Kofanova, Olga; Crowe, John H

2016-04-01

Several approaches to the preservation of biological materials at ambient temperature and the relative impact on sample stability and degradation are reviewed, with a focus on nucleic acids. This appraisal is undertaken within the framework of biobank risk, quality management systems, and accreditation, with a view to assessing how best to apply ambient temperature sample storage to ensure stability, reduce costs, improve handling logistics, and increase the efficiency of biobank procedures.

X-ray imaging with sub-micron resolution using large-area photon counting detectors Timepix

NASA Astrophysics Data System (ADS)

Dudak, J.; Karch, J.; Holcova, K.; Zemlicka, J.

2017-12-01

As X-ray micro-CT became a popular tool for scientific purposes a number of commercially available CT systems have emerged on the market. Micro-CT systems have, therefore, become widely accessible and the number of research laboratories using them constantly increases. However, even when CT scans with spatial resolution of several micrometers can be performed routinely, data acquisition with sub-micron precision remains a complicated task. Issues come mostly from prolongation of the scan time inevitably connected with the use of nano-focus X-ray sources. Long exposure time increases the noise level in the CT projections. Furthermore, considering the sub-micron resolution even effects like source-spot drift, rotation stage wobble or thermal expansion become significant and can negatively affect the data. The use of dark-current free photon counting detectors as X-ray cameras for such applications can limit the issue of increased image noise in the data, however the mechanical stability of the whole system still remains a problem and has to be considered. In this work we evaluate the performance of a micro-CT system equipped with nano-focus X-ray tube and a large area photon counting detector Timepix for scans with effective pixel size bellow one micrometer.

Married and Cohabiting Parents' Relationship Stability: A Focus on Race and Ethnicity

ERIC Educational Resources Information Center

Osborne, Cynthia; Manning, Wendy D.; Smock, Pamela J.

2007-01-01

We draw on three waves of the Fragile Families Study (N = 2,249) to examine family stability among a recent birth cohort of children. We find that children born to cohabiting versus married parents have over five times the risk of experiencing their parents' separation. This difference in union stability is greatest for White children, as compared…

Divergence instability of pipes conveying fluid with uncertain flow velocity

NASA Astrophysics Data System (ADS)

Rahmati, Mehdi; Mirdamadi, Hamid Reza; Goli, Sareh

2018-02-01

This article deals with investigation of probabilistic stability of pipes conveying fluid with stochastic flow velocity in time domain. As a matter of fact, this study has focused on the randomness effects of flow velocity on stability of pipes conveying fluid while most of research efforts have only focused on the influences of deterministic parameters on the system stability. The Euler-Bernoulli beam and plug flow theory are employed to model pipe structure and internal flow, respectively. In addition, flow velocity is considered as a stationary random process with Gaussian distribution. Afterwards, the stochastic averaging method and Routh's stability criterion are used so as to investigate the stability conditions of system. Consequently, the effects of boundary conditions, viscoelastic damping, mass ratio, and elastic foundation on the stability regions are discussed. Results delineate that the critical mean flow velocity decreases by increasing power spectral density (PSD) of the random velocity. Moreover, by increasing PSD from zero, the type effects of boundary condition and presence of elastic foundation are diminished, while the influences of viscoelastic damping and mass ratio could increase. Finally, to have a more applicable study, regression analysis is utilized to develop design equations and facilitate further analyses for design purposes.

Modelling of cayenne production in Central Java using ARIMA-GARCH

NASA Astrophysics Data System (ADS)

Tarno; Sudarno; Ispriyanti, Dwi; Suparti

2018-05-01

Some regencies/cities in Central Java Province are known as producers of horticultural crops in Indonesia, for example, Brebes which is the largest area of shallot producer in Central Java, while the others, such as Cilacap and Wonosobo are the areas of cayenne commodities production. Currently, cayenne is a strategic commodity and it has broad impact to Indonesian economic development. Modelling the cayenne production is necessary to predict about the commodity to meet the need for society. The needs fulfillment of society will affect stability of the concerned commodity price. Based on the reality, the decreasing of cayenne production will cause the increasing of society’s basic needs price, and finally it will affect the inflation level at that area. This research focused on autoregressive integrated moving average (ARIMA) modelling by considering the effect of autoregressive conditional heteroscedasticity (ARCH) to study about cayenne production in Central Java. The result of empirical study of ARIMA-GARCH modelling for cayenne production in Central Java from January 2003 to November 2015 is ARIMA([1,3],0,0)-GARCH(1,0) as the best model.

Dimensional Stability of Grout-Type Materials Used as Connections for Prefabricated Bridge Elements

DOT National Transportation Integrated Search

2016-05-01

The research presented in this report focuses on addressing performance concerns related to dimensional stability (primarily early age shrinkage) of 11 commercially available grout-type materials. Some of these grouts, especially those classified as ...

Focus expansion and stability of the spread parameter estimate of the power law model for dispersal gradients

PubMed Central

Gent, David H.; Mehra, Lucky K.; Christie, David; Magarey, Roger

2017-01-01

Empirical and mechanistic modeling indicate that pathogens transmitted via aerially dispersed inoculum follow a power law, resulting in dispersive epidemic waves. The spread parameter (b) of the power law model, which is an indicator of the distance of the epidemic wave front from an initial focus per unit time, has been found to be approximately 2 for several animal and plant diseases over a wide range of spatial scales under conditions favorable for disease spread. Although disease spread and epidemic expansion can be influenced by several factors, the stability of the parameter b over multiple epidemic years has not been determined. Additionally, the size of the initial epidemic area is expected to be strongly related to the final epidemic extent for epidemics, but the stability of this relationship is also not well established. Here, empirical data of cucurbit downy mildew epidemics collected from 2008 to 2014 were analyzed using a spatio-temporal model of disease spread that incorporates logistic growth in time with a power law function for dispersal. Final epidemic extent ranged from 4.16 ×108 km2 in 2012 to 6.44 ×108 km2 in 2009. Current epidemic extent became significantly associated (P < 0.0332; 0.56 < R2 < 0.99) with final epidemic area beginning near the end of April, with the association increasing monotonically to 1.0 by the end of the epidemic season in July. The position of the epidemic wave-front became exponentially more distant with time, and epidemic velocity increased linearly with distance. Slopes from the temporal and spatial regression models varied with about a 2.5-fold range across epidemic years. Estimates of b varied substantially ranging from 1.51 to 4.16 across epidemic years. We observed a significant b ×time (or distance) interaction (P < 0.05) for epidemic years where data were well described by the power law model. These results suggest that the spread parameter b may not be stable over multiple epidemic years. However, b ≈ 2 may be considered the lower limit of the distance traveled by epidemic wave-fronts for aerially transmitted pathogens that follow a power law dispersal function. PMID:28649473

Model-based calculations of surface mass balance of mountain glaciers for the purpose of water consumption planning: focus on Djankuat Glacier (Central Caucasus)

NASA Astrophysics Data System (ADS)

Rybak, O. O.; Rybak, E. A.

2018-01-01

Mountain glaciers act as regulators of run-off in the summer period, which is very crucial for economy especially in dynamically developing regions with rapidly growing population, such as Central Asia or the Northern Caucasus in Russia. In overall, glaciers stabilize water consumption in comparatively arid areas and provide conditions for sustainable development of the economy in mountainous regions and in the surrounding territories. A proper prediction of the glacial run-off is required to elaborate strategies of the regional development. This goal can be achieved by implementation of mathematical modeling methods into planning methodologies. In the paper, we consider one of the first steps in glacier dynamical modeling - surface mass balance simulation. We focus on the Djankuat Glacier in the Central Caucasus, where regular observations have been conducted during the last fifty years providing an exceptional opportunity to calibrate and to validate a mathematical model.

Toxicity of carbon nanotubes: A review.

PubMed

Francis, Arul Prakash; Devasena, Thiyagarajan

2018-03-01

Carbon nanotubes (CNTs) are widely used in the aerospace, automotive, and electronics industries because of their stability, enhanced metallic, and electrical properties. CNTs are also being investigated for biomedical applications such as drug delivery systems and biosensors. However, the toxic potential of CNTs was reported in various cell lines and animal models. The toxicity depends on diverse properties of the CNTs, such as length, aspect ratio, surface area, degree of aggregation, purity, concentration, and dose. In addition, CNTs and/or associated contaminants were well known for oxidative stress, inflammation, apoptosis, pulmonary inflammation, fibrosis, and granuloma in lungs. The increased production of CNTs likely enhanced the possibility of its exposure in people. Studies on the toxicity of CNTs are mainly focused on the pulmonary effects after intratracheal administration, and only a few studies are reported about the toxicity of CNTs via other routes of exposure. So, it is essential to consider the chronic toxicity of CNTs before using them for various biomedical applications. This review focuses on the potential toxicities of CNTs.

Posttranslational Modifications and Plant-Environment Interaction.

PubMed

Hashiguchi, A; Komatsu, S

2017-01-01

Posttranslational modifications (PTMs) of proteins such as phosphorylation and ubiquitination are crucial for controlling protein stability, localization, and conformation. Genetic information encoded in DNA is transcribed, translated, and increases its complexity by multiple PTMs. Conformational change introduced by PTMs affects interacting partners of each proteins and their downstream signaling; therefore, PTMs are the major level of modulations of total outcome of living cells. Plants are living in harsh environment that requires unremitting physiological modulation to survive, and the plant response to various environment stresses is regulated by PTMs of proteins. This review deals with the novel knowledge of PTM-focused proteomic studies on various life conditions. PTMs are focused that mediate plant-environment interaction such as stress perception, protein homeostasis, control of energy shift, and defense by immune system. Integration of diverse signals on a protein via multiple PTMs is discussed as well, considering current situation where signal integration became an emerging area approached by systems biology into account. © 2017 Elsevier Inc. All rights reserved.

Stability of biogenic metal(loid) nanomaterials related to the colloidal stabilization theory of chemical nanostructures.

PubMed

Piacenza, Elena; Presentato, Alessandro; Turner, Raymond J

2018-02-25

In the last 15 years, the exploitation of biological systems (i.e. plants, bacteria, mycelial fungi, yeasts, and algae) to produce metal(loid) (Me)-based nanomaterials has been evaluated as eco-friendly and a cost-effective alternative to the chemical synthesis processes. Although the biological mechanisms of biogenic Me-nanomaterial (Bio-Me-nanomaterials) production are not yet completely elucidated, a key advantage of such bio-nanostructures over those chemically synthesized is related to their natural thermodynamic stability, with several studies ascribed to the presence of an organic layer surrounding these Bio-Me-nanostructures. Different macromolecules (e.g. proteins, peptides, lipids, DNA, and polysaccharides) or secondary metabolites (e.g. flavonoids, terpenoids, glycosides, organic acids, and alkaloids) naturally produced by organisms have been indicated as main contributors to the stabilization of Bio-Me-nanostructures. Nevertheless, the chemical-physical mechanisms behind the ability of these molecules in providing stability to Bio-Me-nanomaterials are unknown. In this context, transposing the stabilization theory of chemically synthesized Me-nanomaterials (Ch-Me-nanomaterials) to biogenic materials can be used towards a better comprehension of macromolecules and secondary metabolites role as stabilizing agents of Bio-Me-nanomaterials. According to this theory, nanomaterials are generally featured by high thermodynamic instability in suspension, due to their high surface area and surface energy. This feature leads to the necessity to stabilize chemical nanostructures, even during or directly after their synthesis, through the development of (i) electrostatic, (ii) steric, or (iii) electrosteric interactions occurring between molecules and nanomaterials in suspension. Based on these three mechanisms, this review is focused on parallels between the stabilization of biogenic or chemical nanomaterials, suggesting which chemical-physical mechanisms may be involved in the natural stability of Bio-Me-nanomaterials. As a result, macromolecules such as DNA, polyphosphates and proteins may electrostatically interact with Bio-Me-nanomaterials in suspension through their charged moieties, showing the same properties of counterions in Ch-Me-nanostructure suspensions. Since several biomolecules (e.g. neutral lipids, nonionic biosurfactants, polysaccharides, and secondary metabolites) produced by metal(loid)-grown organisms can develop similar steric hindrance as compared to nonionic amphiphilic surfactants and block co-polymers generally used to sterically stabilize Ch-Me-nanomaterials. These biomolecules, most likely, are involved in the development of steric stabilization, because of their bulky structures. Finally, charged lipids and polysaccharides, ionic biosurfactants or proteins with amphiphilic properties can exert a dual effect (i.e. electrostatic and steric repulsion interactions) in the contest of Bio-Me-nanomaterials, leading to the high degree of stability observed.

NASA's Next Solar Sail: Lessons Learned from NanoSail - D2

NASA Technical Reports Server (NTRS)

Katan, Chelsea

2012-01-01

NanoSail-D2 unfurled January 17th, 2011 and commenced a nine month Low Earth Orbit path to reentry to evaluate a sail's capacity to deploy in space and deorbit satellites. The orbit was strongly affected by variables including but not limited to: initial attitude, orbit lighting, solar radiation pressure, aerodynamic drag, gravity, and Center of Pressure offsets. The effects of these variables were evaluated through a 3-DOF rigid body simulation. The sail experienced stability in orbits which were continuously lit, i.e. did not orbit behind Earth. Probable drag area experienced by the sail for the mission is also estimated from orbital data and compared to the attitude simulation results. Analysis focuses on sail behavior in full lighting conditions to establish the limits of the sails stability in full lighting. Solar radiation pressure, aerodynamic drag, and gravity torque effects are described. Lastly, a reasonable upper bound on the variation of the Center of Pressure from the geometric center of the sail plane is established. Each of these results contributes to the design requirements for future solar sails.

Specific Visualization of Tumor Cells Using Upconversion Nanophosphors

PubMed Central

Grebenik, E. A.; Generalova, A. N.; Nechaev, A. V.; Khaydukov, E.V.; Mironova, K. E.; Stremovskiy, O. A.; Lebedenko, E.N.; Zvyagin, A. V.; Deyev, S. M.

2014-01-01

The development of targeted constructs on the basis of photoluminescent nanoparticles with a high photo- and chemical stability and absorption/emission spectra in the “transparency window” of biological tissues is an important focus area of present-day medical diagnostics. In this work, a targeted two-component construct on the basis of upconversion nanophosphors (UCNPs) and anti-tumor 4D5 scFv was developed for selective labeling of tumor cells overexpressing the HER2 tumor marker characteristic of a number of human malignant tumors. A high affinity barnase : barstar (Bn : Bs) protein pair, which exhibits high stability in a wide range of pH and temperatures, was exploited as a molecular adapter providing self-assembly of the two-component construct. High selectivity for the binding of the two-component 4D5 scFv-Bn : UCNP-Bs construct to human breast adenocarcinoma SK-BR-3 cells overexpressing HER2 was demonstrated. This approach provides an opportunity to produce similar constructs for the visualization of different specific markers in pathogenic tissues, including malignant tumors. PMID:25558394

Immobilization, stabilization and patterning techniques for enzyme based sensor systems.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Flounders, A.W.; Carichner, S.C.; Singh, A.K.

1997-01-01

Sandia National Laboratories has recently opened the Chemical and Radiation Detection Laboratory (CRDL) in Livermore CA to address the detection needs of a variety of government agencies (e.g., Department of Energy, Environmental Protection Agency, Department of Agriculture) as well as provide a fertile environment for the cooperative development of new industrial technologies. This laboratory consolidates a variety of existing chemical and radiation detection efforts and enables Sandia to expand into the novel area of biochemically based sensors. One aspect of this biosensor effort is further development and optimization of enzyme modified field effect transistors (EnFETs). Recent work has focused uponmore » covalent attachment of enzymes to silicon dioxide and silicon nitride surfaces for EnFET fabrication. They are also investigating methods to pattern immobilized proteins; a critical component for development of array-based sensor systems. Novel enzyme stabilization procedures are key to patterning immobilized enzyme layers while maintaining enzyme activity. Results related to maximized enzyme loading, optimized enzyme activity and fluorescent imaging of patterned surfaces will be presented.« less

Cold-Adapted Enzymes

NASA Astrophysics Data System (ADS)

Georlette, D.; Bentahir, M.; Claverie, P.; Collins, T.; D'amico, S.; Delille, D.; Feller, G.; Gratia, E.; Hoyoux, A.; Lonhienne, T.; Meuwis, M.-a.; Zecchinon, L.; Gerday, Ch.

In the last few years, increased attention has been focused on enzymes produced by cold-adapted micro-organisms. It has emerged that psychrophilic enzymes represent an extremely powerful tool in both protein folding investigations and for biotechnological purposes. Such enzymes are characterised by an increased thermosensitivity and, most of them, by a higher catalytic efficiency at low and moderate temperatures, when compared to their mesophilic counterparts. The high thermosensitivity probably originates from an increased flexibility of either a selected area of the molecular edifice or the overall protein structure, providing enhanced abilities to undergo conformational changes during catalysis at low temperatures. Structure modelling and recent crystallographic data have allowed to elucidate the structural parameters that could be involved in this higher resilience. It was demonstrated that each psychrophilic enzyme adopts its own adaptive strategy. It appears, moreover, that there is a continuum in the strategy of protein adaptation to temperature, as the previously mentioned structural parameters are implicated in the stability of thermophilic proteins. Additional 3D crystal structures, site-directed and random mutagenesis experiments should now be undertaken to further investigate the stability-flexibility-activity relationship.

Study of locations’characteristics for stabilization of street vendors in Surakarta City

NASA Astrophysics Data System (ADS)

Rahayu, M. J.; Buchori, I.; Widjajanti, R.

2018-01-01

Street vendors are usually centered around particular areas where they have made adaptations based on their activities, instead of scattered all over the city. These locations tend to be close to street vendors’ primary activities and consumers, occupy the public lands, and are productive and accessible. The Municipality of Surakarta has managed the street vendors in the form of stabilization and relocation. In Surakarta, there are 24 areas used for stabilization of street vendors varying in characteristics and quantities. This study uses a spatial analysis aiming to explain the characteristics of locations used for stabilization of street vendors and to identify their physical condition and arrangement. Furthermore, all of the research results will be used as the criteria in choosing the new locations that are suitable for the street vendors’ characteristics and consumers’ preference. The results show that the locations are on the roadsides of the neighborhood, local, and secondary collector roads. The traffic conditions in the stabilization areas are ranging from the very busy until relatively busy level since they are close to activities for trade, education, recreation, offices, and settlements.

Stability Analysis of Railway Subgrade in Mining Area Based on Dinsar

NASA Astrophysics Data System (ADS)

Xu, J.; Hu, J.; Ding, J.

2018-04-01

DInSAR technology have been applied to monitor the mining subsidence and the stability of the railway subgrade. A total of 10 Sentinel-1A images acquired from 2015/9/26 to 2016/2/23 were used in DInSAR analysis. The study mining area is about 13.4 km2. Mining have induced serious land subsidence involve a large area that causing different levels of damages to infrastructures on the land. There is an important railway near the mining area, the DInSAR technology is applied to analyse the subsidence near the railway, which can warn early the possible deformation that may occur during underground mining. The DInSAR results was verified by the field measurement. The results show that the mining did not cause subsidence of railway subgrade and did not affect the stability of railway subgrade.

Spatial and temporal variability of throughfall and soil moisture in a deciduous forest in the low mountain ranges (Hesse, Germany)

NASA Astrophysics Data System (ADS)

Chifflard, Peter; Weishaupt, Philipp; Reiss, Martin

2017-04-01

Spatial and temporal patterns of throughfall can affect the heterogeneity of ecological, biogeochemical and hydrological processes at a forest floor and further the underlying soil. Previous research suggests different factors controlling the spatial and temporal patterns of throughfall, but most studies focus on coniferous forest, where the vegetation coverage is more or less constant over time. In deciduous forests the leaf area index varies due to the leaf fall in autumn which implicates a specific spatial and temporal variability of throughfall and furthermore of the soil moisture. Therefore, in the present study, the measurements of throughfall and soil moisture in a deciduous forest in the low mountain ranges focused especially on the period of leaf fall. The aims of this study were: 1) to detect the spatial and temporal variability of both the throughfall and the soil moisture, 2) to examine the temporal stability of the spatial patterns of the throughfall and soil moisture and 3) relate the soil moisture patterns to the throughfall patterns and further to the canopy characteristics. The study was carried out in a small catchment on middle Hesse (Germany) which is covered by beech forest. Annual mean air temperature is 9.4°C (48.9˚F) and annual mean precipitation is 650 mm. Base materials for soil genesis is greywacke and clay shale from Devonian deposits. The soil type at the study plot is a shallow cambisol. The study plot covers an area of about 150 m2 where 77 throughfall samplers where installed. The throughfall and the soil moisture (FDR-method, 20 cm depth) was measured immediately after every rainfall event at the 77 measurement points. During the period of October to December 2015 altogether 7 events were investigated. The geostatistical method kriging was used to interpolate between the measurements points to visualize the spatial patterns of each investigated parameter. Time-stability-plots were applied to examine temporal scatters of each investigated parameter. The spearmen and pearson correlation coefficients were applied to detect the relationship between the different investigated parameters. First results show that the spatial variability of throughfall decreases if the total amount of the throughfall increases. The soil moisture shows a similar behavior. It`s spatial variability decreases if higher soil moisture values were measured. Concerning the temporal stability of throughfall it can be shown that it is very high during the leaf-free period, although the rainfall events have different total througfall amounts. The soil moisture patterns consists of a low temporal stability and additionally only during one event a significant correlations between throughfall and soil moisture patterns exists. This implies that other factors than the throughfall patterns control the spatial patterns of soil moisture.

Prediction of stemless humeral implant micromotion during upper limb activities.

PubMed

Favre, Philippe; Henderson, Adam D

2016-07-01

Adequate primary stability is essential for the long term success of uncemented stemless shoulder implants. The goal of this study was to evaluate the micromotion of a stemless humeral implant during various upper limb activities. A finite element model was validated by reproducing experimental primary stability testing. Loading from an instrumented prosthesis representing a set of 29 upper limb activities were applied within the validated FE model. Peak micromotion and percentage area for different micromotion thresholds were considered. In all simulated activities, at least 99% of the implant surface experienced micromotion below 150μm. Micromotion depended strongly on loading with large discrepancies between upper limb activities. Carrying no external weight and keeping the arm at lower angles induced lower micromotion. Activities representative of demanding manual labor generally led to higher micromotion. Axilla crutches led to lower micromotion than forearm crutches. Micromotion increased when a wheelchair was used on slopes above 2% inclination. Micromotions below the 150μm threshold below which bone ingrowth occurs were measured over at least 99% of the implant surface for all simulated activities. Peak micromotion dependence on activity type demonstrates the need to consider physiologic in vivo loading and the full contact interface in primary stability evaluations. Focusing on activities with no hand weight and low arm motions during the rehabilitation period may enhance primary stability. For patients unable to walk without aids, axilla crutches and motorized wheelchairs might be more beneficial than forearm crutches and manual drive wheelchairs respectively. Copyright © 2016 Elsevier Ltd. All rights reserved.

"Fire Moss" Cover and Function in Severely Burned Forests of the Western United States

NASA Astrophysics Data System (ADS)

Grover, H.; Doherty, K.; Sieg, C.; Robichaud, P. R.; Fulé, P. Z.; Bowker, M.

2017-12-01

With wildfires increasing in severity and extent throughout the Western United States, land managers need new tools to stabilize recently burned ecosystems. "Fire moss" consists of three species, Ceratodon purpureus, Funaria hygrometrica, and Bryum argentum. These mosses colonize burned landscapes quickly, aggregate soils, have extremely high water holding capacity, and can be grown rapidly ex-situ. In this talk, I will focus on our efforts to understand how Fire Moss naturally interacts with severely burned landscapes. We examined 14 fires in Arizona, New Mexico, Washington, and Idaho selecting a range of times since fire, and stratified plots within each wildfire by winter insolation and elevation. At 75+ plots we measured understory plant cover, ground cover, Fire Moss cover, and Fire Moss reproductive effort. On plots in the Southwest, we measured a suite of soil characteristics on moss covered and adjacent bare soil including aggregate stability, shear strength, compressional strength, and infiltration rates. Moss cover ranged from 0-75% with a mean of 16% across all plots and was inversely related to insolation (R2 = .32, p = <.01), directly related to elevation (R2 = .13, p = .02), and not related to slope (R2 = .02, p =.41). Moss covered areas had twice as much shear strength and compressional strength, and three times higher aggregate stability and infiltration rates as adjacent bare ground. These results will allow us to model locations where Fire Moss will naturally increase postfire hillslope soil stability, locations for targeting moss restoration efforts, and suggest that Fire Moss could be a valuable tool to mitigate post wildfire erosion.

Lineage range estimation method reveals fine-scale endemism linked to Pleistocene stability in Australian rainforest herpetofauna.

PubMed

Rosauer, Dan F; Catullo, Renee A; VanDerWal, Jeremy; Moussalli, Adnan; Moritz, Craig

2015-01-01

Areas of suitable habitat for species and communities have arisen, shifted, and disappeared with Pleistocene climate cycles, and through this shifting landscape, current biodiversity has found paths to the present. Evolutionary refugia, areas of relative habitat stability in this shifting landscape, support persistence of lineages through time, and are thus crucial to the accumulation and maintenance of biodiversity. Areas of endemism are indicative of refugial areas where diversity has persisted, and endemism of intraspecific lineages in particular is strongly associated with late-Pleistocene habitat stability. However, it remains a challenge to consistently estimate the geographic ranges of intraspecific lineages and thus infer phylogeographic endemism, because spatial sampling for genetic analyses is typically sparse relative to species records. We present a novel technique to model the geographic distribution of intraspecific lineages, which is informed by the ecological niche of a species and known locations of its constituent lineages. Our approach allows for the effects of isolation by unsuitable habitat, and captures uncertainty in the extent of lineage ranges. Applying this method to the arc of rainforest areas spanning 3500 km in eastern Australia, we estimated lineage endemism for 53 species of rainforest dependent herpetofauna with available phylogeographic data. We related endemism to the stability of rainforest habitat over the past 120,000 years and identified distinct concentrations of lineage endemism that can be considered putative refugia. These areas of lineage endemism are strongly related to historical stability of rainforest habitat, after controlling for the effects of current environment. In fact, a dynamic stability model that allows movement to track suitable habitat over time was the most important factor in explaining current patterns of endemism. The techniques presented here provide an objective, practical method for estimating geographic ranges below the species level, and including them in spatial analyses of biodiversity.

Lineage Range Estimation Method Reveals Fine-Scale Endemism Linked to Pleistocene Stability in Australian Rainforest Herpetofauna

PubMed Central

Rosauer, Dan F.; Catullo, Renee A.; VanDerWal, Jeremy; Moussalli, Adnan; Moritz, Craig

2015-01-01

Areas of suitable habitat for species and communities have arisen, shifted, and disappeared with Pleistocene climate cycles, and through this shifting landscape, current biodiversity has found paths to the present. Evolutionary refugia, areas of relative habitat stability in this shifting landscape, support persistence of lineages through time, and are thus crucial to the accumulation and maintenance of biodiversity. Areas of endemism are indicative of refugial areas where diversity has persisted, and endemism of intraspecific lineages in particular is strongly associated with late-Pleistocene habitat stability. However, it remains a challenge to consistently estimate the geographic ranges of intraspecific lineages and thus infer phylogeographic endemism, because spatial sampling for genetic analyses is typically sparse relative to species records. We present a novel technique to model the geographic distribution of intraspecific lineages, which is informed by the ecological niche of a species and known locations of its constituent lineages. Our approach allows for the effects of isolation by unsuitable habitat, and captures uncertainty in the extent of lineage ranges. Applying this method to the arc of rainforest areas spanning 3500 km in eastern Australia, we estimated lineage endemism for 53 species of rainforest dependent herpetofauna with available phylogeographic data. We related endemism to the stability of rainforest habitat over the past 120,000 years and identified distinct concentrations of lineage endemism that can be considered putative refugia. These areas of lineage endemism are strongly related to historical stability of rainforest habitat, after controlling for the effects of current environment. In fact, a dynamic stability model that allows movement to track suitable habitat over time was the most important factor in explaining current patterns of endemism. The techniques presented here provide an objective, practical method for estimating geographic ranges below the species level, and including them in spatial analyses of biodiversity. PMID:26020936

Nanoporous microbead supported bilayers: stability, physical characterization, and incorporation of functional transmembrane proteins.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davis, Ryan W.; Brozik, James A.; Brozik, Susan Marie

2007-03-01

The introduction of functional transmembrane proteins into supported bilayer-based biomimetic systems presents a significant challenge for biophysics. Among the various methods for producing supported bilayers, liposomal fusion offers a versatile method for the introduction of membrane proteins into supported bilayers on a variety of substrates. In this study, the properties of protein containing unilamellar phosphocholine lipid bilayers on nanoporous silica microspheres are investigated. The effects of the silica substrate, pore structure, and the substrate curvature on the stability of the membrane and the functionality of the membrane protein are determined. Supported bilayers on porous silica microspheres show a significant increasemore » in surface area on surfaces with structures in excess of 10 nm as well as an overall decrease in stability resulting from increasing pore size and curvature. Comparison of the liposomal and detergent-mediated introduction of purified bacteriorhodopsin (bR) and the human type 3 serotonin receptor (5HT3R) are investigated focusing on the resulting protein function, diffusion, orientation, and incorporation efficiency. In both cases, functional proteins are observed; however, the reconstitution efficiency and orientation selectivity are significantly enhanced through detergent-mediated protein reconstitution. The results of these experiments provide a basis for bulk ionic and fluorescent dye-based compartmentalization assays as well as single-molecule optical and single-channel electrochemical interrogation of transmembrane proteins in a biomimetic platform.« less

Elucidation of Metallic Plume and Spatter Characteristics Based on SVM During High-Power Disk Laser Welding

NASA Astrophysics Data System (ADS)

Gao, Xiangdong; Liu, Guiqian

2015-01-01

During deep penetration laser welding, there exist plume (weak plasma) and spatters, which are the results of weld material ejection due to strong laser heating. The characteristics of plume and spatters are related to welding stability and quality. Characteristics of metallic plume and spatters were investigated during high-power disk laser bead-on-plate welding of Type 304 austenitic stainless steel plates at a continuous wave laser power of 10 kW. An ultraviolet and visible sensitive high-speed camera was used to capture the metallic plume and spatter images. Plume area, laser beam path through the plume, swing angle, distance between laser beam focus and plume image centroid, abscissa of plume centroid and spatter numbers are defined as eigenvalues, and the weld bead width was used as a characteristic parameter that reflected welding stability. Welding status was distinguished by SVM (support vector machine) after data normalization and characteristic analysis. Also, PCA (principal components analysis) feature extraction was used to reduce the dimensions of feature space, and PSO (particle swarm optimization) was used to optimize the parameters of SVM. Finally a classification model based on SVM was established to estimate the weld bead width and welding stability. Experimental results show that the established algorithm based on SVM could effectively distinguish the variation of weld bead width, thus providing an experimental example of monitoring high-power disk laser welding quality.

The DYNAFLUX / DYNACOLD (Dynamics, Fluxes, Stability, Succession and Landscape Formation in Cold Environments) Network (2004-2017)

NASA Astrophysics Data System (ADS)

Beylich, Achim A.

2017-04-01

There is a wide range of high-latitude and high-altitude cold climate landscapes within Europe, covering a significant proportion of the total land surface area. This spectrum of defined cold-climate landscapes represents a variety of stages of deglaciation history and landscape formation. We can find landscapes at different levels of postglacial stabilization which is providing the unique opportunity to study the interactions between geo-, bio-, social and socio-economic systems at the land surface. The DYNAFLUX / DYNACOLD Network (2004-2017) bridges across the geo-, bio-, social and socio-economic sciences in order to analyze the complex dynamics of adjustment, stabilization, succession and landscape formation during and after ice retreat and under ongoing anthropogenic influences. The network provides a multidisciplinary forum where researchers come together and discuss. In addition, this network is linking a number of other scientific networks, working groups and programs and creates an umbrella network and a forum for sharing knowledge and experience. The scientific focus of DYNAFLUX / DYNACOLD is also relevant for a number of end users, including risk and vulnerability assessment, sustainable land use, land management and conservation. In addition, present key questions related to environmental change like, e.g., hazards, permafrost degradation and loss of biodiversity are addressed and discussed. Further information is found under http://www.ngu.no/sediflux.

Rock face stability analysis and potential rockfall source detection in Yosemite Valley

NASA Astrophysics Data System (ADS)

Matasci, B.; Stock, G. M.; Jaboyedoff, M.; Oppikofer, T.; Pedrazzini, A.; Carrea, D.

2012-04-01

Rockfall hazard in Yosemite Valley is especially high owing to the great cliff heights (~1 km), the fracturing of the steep granitic cliffs, and the widespread occurrence of surface parallel sheeting or exfoliation joints. Between 1857 and 2011, 890 documented rockfalls and other slope movements caused 15 fatalities and at least 82 injuries. The first part of this study focused on realizing a structural study for Yosemite Valley at both regional (valley-wide) and local (rockfall source area) scales. The dominant joint sets were completely characterized by their orientation, persistence, spacing, roughness and opening. Spacing and trace length for each joint set were accurately measured on terrestrial laser scanning (TLS) point clouds with the software PolyWorks (InnovMetric). Based on this fundamental information the second part of the study aimed to detect the most important failure mechanisms leading to rockfalls. With the software Matterocking and the 1m cell size DEM, we calculated the number of possible failure mechanisms (wedge sliding, planar sliding, toppling) per cell, for several cliffs of the valley. Orientation, spacing and persistence measurements directly issued from field and TLS data were inserted in the Matterocking calculations. TLS point clouds are much more accurate than the 1m DEM and show the overhangs of the cliffs. Accordingly, with the software Coltop 3D we developed a methodology similar to the one used with Matterocking to identify on the TLS point clouds the areas of a cliff with the highest number of failure mechanisms. Exfoliation joints are included in this stability analysis in the same way as the other joint sets, with the only difference that their orientation is parallel to the local cliff orientation and thus variable. This means that, in two separate areas of a cliff, the exfoliation joint set is taken into account with different dip direction and dip, but its effect on the stability assessment is the same. Areas with a high density of possible failure mechanisms are shown to be more susceptible to rockfalls, demonstrating a link between high fracture density and rockfall susceptibility. This approach enables locating the most probable future rockfall sources and provides key elements needed to evaluate the potential volume and run-out distance of rockfall blocks. This information is used to improve rockfall hazard assessment in Yosemite Valley and elsewhere.

Nanoparticles: A Challenging Vehicle for Neural Stimulation

PubMed Central

Colombo, Elisabetta; Feyen, Paul; Antognazza, Maria Rosa; Lanzani, Guglielmo; Benfenati, Fabio

2016-01-01

Neurostimulation represents a powerful and well-established tool for the treatment of several diseases affecting the central nervous system. Although, effective in reducing the symptoms or the progression of brain disorders, the poor accessibility of the deepest areas of the brain currently hampers the possibility of a more specific and controlled therapeutic stimulation, depending on invasive surgical approaches and long-term stability, and biocompatibility issues. The massive research of the last decades on nanomaterials and nanoscale devices favored the development of new tools to address the limitations of the available neurostimulation approaches. This mini-review focuses on the employment of nanoparticles for the modulation of the electrophysiological activity of neuronal networks and the related transduction mechanisms underlying the nanostructure-neuron interfaces. PMID:27047327

Liquid lens based on electrowetting: actual developments on larger aperture and multiple electrodes design for image stabilization or beam steering

NASA Astrophysics Data System (ADS)

Berge, Bruno; Broutin, Jérôme; Gaton, Hilario; Malet, Géraldine; Simon, Eric; Thieblemont, Florent

2013-03-01

This paper presents experimental results on several liquid lenses based on Electrowetting which are commercially available. It will be shown that larger aperture lenses are basically of the same optical quality than smaller lenses, sometimes reaching the diffraction limit, then opening new kind of applications areas for variable lenses in laser science. Regarding response time, actual performances of liquids lenses based on Electrowetting are presented and compared to a model simulating the internal fluid reorganization, seen as the main source of delay between electrical actuation and optical evolution of the lens. This simplified analytical model is supporting experimental results in various situations (focus and tilt variations), in static and dynamic regimes.

GELATIN CARRIERS FOR DRUG AND CELL DELIVERY IN TISSUE ENGINEERING

PubMed Central

Santoro, Marco; Tatara, Alexander M.; Mikos, Antonios G.

2014-01-01

The ability of gelatin to form complexes with different drugs has been investigated for controlled release applications. Gelatin parameters, such as crosslinking density and isoelectric point, have been tuned in order to optimize gelatin degradation and drug delivery kinetics. In recent years, focus has shifted away from the use of gelatin in isolation towards the modification of gelatin with functional groups and the fabrication of material composites with embedded gelatin carriers. In this review, we highlight some of the latest work being performed in these areas and comment on trends in the field. Specifically, we discuss gelatin modifications for immune system evasion, drug stabilization, and targeted delivery, as well as gelatin composite systems based on ceramics, naturally-occurring polymers, and synthetic polymers. PMID:24746627

Systems Integration Fact Sheet

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2016-06-01

This fact sheet is an overview of the Systems Integration subprogram at the U.S. Department of Energy SunShot Initiative. The Systems Integration subprogram enables the widespread deployment of safe, reliable, and cost-effective solar energy technologies by addressing the associated technical and non-technical challenges. These include timely and cost-effective interconnection procedures, optimal system planning, accurate prediction of solar resources, monitoring and control of solar power, maintaining grid reliability and stability, and many more. To address the challenges associated with interconnecting and integrating hundreds of gigawatts of solar power onto the electricity grid, the Systems Integration program funds research, development, and demonstrationmore » projects in four broad, interrelated focus areas: grid performance and reliability, dispatchability, power electronics, and communications.« less

On controlling networks of limit-cycle oscillators

NASA Astrophysics Data System (ADS)

Skardal, Per Sebastian; Arenas, Alex

2016-09-01

The control of network-coupled nonlinear dynamical systems is an active area of research in the nonlinear science community. Coupled oscillator networks represent a particularly important family of nonlinear systems, with applications ranging from the power grid to cardiac excitation. Here, we study the control of network-coupled limit cycle oscillators, extending the previous work that focused on phase oscillators. Based on stabilizing a target fixed point, our method aims to attain complete frequency synchronization, i.e., consensus, by applying control to as few oscillators as possible. We develop two types of controls. The first type directs oscillators towards larger amplitudes, while the second does not. We present numerical examples of both control types and comment on the potential failures of the method.

China’s Currency: A Summary of the Economic Issues

DTIC Science & Technology

2008-11-20

policy is not meant to favor exports over imports, but instead to foster economic stability through currency stability, as many other countries do...farmers (due to lower-priced imports). Chinese officials view economic stability as critical to sustaining political stability; they fear an...consumption and the development of rural areas, but they claim they want to proceed at a gradual pace to ensure economic stability . These concerns have

China’s Currency: A Summary of the Economic Issues

DTIC Science & Technology

2009-01-29

that its currency policy is not meant to favor exports over imports, but instead to foster economic stability through currency stability, as many...have on farmers (due to lower-priced imports). Chinese officials view economic stability as critical to sustaining political stability; they fear an...domestic consumption and the development of rural areas, but they claim they want to proceed at a gradual pace to ensure economic stability . These

Regional variability of slope stability: Application to the Eel margin, California

USGS Publications Warehouse

Lee, H.; Locat, J.; Dartnell, P.; Israel, K.; Florence, Wong

1999-01-01

Relative values of downslope driving forces and sediment resisting forces determine the locations of submarine slope failures. Both of these vary regionally, and their impact can be addressed when the data are organized in a Geographic Information System (GIS). The study area on the continental margin near the Eel River provides an excellent opportunity to apply GIS spatial analysis techniques for evaluation of slope stability. In this area, swath bathymetric mapping shows seafloor morphology and distribution of slope steepness in fine detail, and sediment analysis of over 70 box cores delineates the variability of sediment density near the seafloor surface. Based on the results of ten geotechnical studies of submarine study areas, we developed an algorithm that relates surface sediment density to the shear strength appropriate to the type of cyclic loading produced by an earthquake. Strength and stress normalization procedures provide results that are conceptually independent of subbottom depth. Results at depth are rigorously applicable if sediment lithology does not vary significantly and consolidation state can be estimated. Otherwise, the method applies only to shallow-seated slope failure. Regional density, slope, and level of anticipated seismic shaking information were combined in a GIS framework to yield a map that illustrates the relative stability of slopes in the face of seismically induced failure. When a measure of predicted relative slope stability is draped on an oblique view of swath bathymetry, a variation in this slope stability is observed on an otherwise smooth slope along the mid-slope region north of a plunging anticline. The section of slope containing diffuse, pockmarked gullies has a lower measure of stability than a separate section containing gullies that have sharper boundaries and somewhat steeper sides. Such an association suggests that our slope-stability analysis relates to the stability of the gully sides. The remainder of the study area shows few obvious indications of slope instability except for a feature that has become known as the 'Humboldt Slide,' but it is too deep-seated to be amenable to the slope-stability-prediction techniques presented herein. In general, few slope failures have been mapped in the Eel margin study area despite the high level of seismicity, the relatively high rates of sediment accumulation, and the extent of gas charging observed by others.

Fall conservation deep tillage stabilizes maize residues into soil organic matter

USDA-ARS?s Scientific Manuscript database

Efforts for increasing soil organic matter (SOM) content under agricultural systems have primarily focused on management practices that reduce exposure of SOM to decomposition via minimum tillage. We assess an alternative approach, termed ‘fall conservation deep tillage’ (FCDT), to SOM stabilization...

Stability condition for the drive bunch in a collinear wakefield accelerator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baturin, S. S.; Zholents, A.

The beam breakup instability of the drive bunch in the structure-based collinear wakefield accelerator is considered and a stabilizing method is proposed. The method includes using the specially designed beam focusing channel, applying the energy chirp along the electron bunch, and keeping energy chirp constant during the drive bunch deceleration. A stability condition is derived that defines the limit on the accelerating field for the witness bunch.

Effectiveness of core stability exercises and recovery myofascial release massage on fatigue in breast cancer survivors: a randomized controlled clinical trial.

PubMed

Cantarero-Villanueva, Irene; Fernández-Lao, Carolina; Del Moral-Avila, Rosario; Fernández-de-Las-Peñas, César; Feriche-Fernández-Castanys, María Belén; Arroyo-Morales, Manuel

2012-01-01

The purpose of the present paper was to evaluate the effects of an 8-week multimodal program focused on core stability exercises and recovery massage with DVD support for a 6-month period in physical and psychological outcomes in breast cancer survivors. A randomized controlled clinical trial was performed. Seventy-eight (n = 78) breast cancer survivors were assigned to experimental (core stability exercises plus massage-myofascial release) and control (usual health care) groups. The intervention period was 8 weeks. Mood state, fatigue, trunk curl endurance, and leg strength were determined at baseline, after the last treatment session, and at 6 months of followup. Immediately after treatment and at 6 months, fatigue, mood state, trunk curl endurance, and leg strength exhibited greater improvement within the experimental group compared to placebo group. This paper showed that a multimodal program focused on core stability exercises and massage reduced fatigue, tension, depression, and improved vigor and muscle strength after intervention and 6 months after discharge.

The Effects of Isolated and Integrated ‘Core Stability’ Training on Athletic Performance Measures

PubMed Central

Reed, Casey A.; Ford, Kevin R.; Myer, Gregory D.; Hewett, Timothy E.

2014-01-01

Background Core stability training, operationally defined as training focused to improve trunk and hip control, is an integral part of athletic development, yet little is known about its direct relation to athletic performance. Objective This systematic review focuses on identification of the association between core stability and sports-related performance measures. A secondary objective was to identify difficulties encountered when trying to train core stability with the goal of improving athletic performance. Data sources A systematic search was employed to capture all articles related to athletic performance and core stability training that were identified using the electronic databases MEDLINE, CINAHL and SPORTDiscus™ (1982-June2011). Study selection A systematic approach was used to evaluate 179 articles identified for initial review. Studies that performed an intervention targeted toward the core and measured an outcome related to athletic or sport performances were included, while studies with a participant population aged 65 years or older were excluded. Twenty-four in total met the inclusionary criteria for review. Study appraisal and synthesis methods Studies were evaluated using the Physical Therapy Evidence Database (PEDro) scale. The 24 articles were separated into three groups, general performance (n = 8), lower extremity (n = 10) and upper extremity (n = 6), for ease of discussion. Results In the majority of studies, core stability training was utilized in conjunction with more comprehensive exercise programmes. As such, many studies saw improvements in skills of general strengths such as maximum squat load and vertical leap. Surprisingly, not all studies reported measurable increases in specific core strength and stability measures following training. Additionally, investigations that targeted the core as the primary goal for improved outcome of training had mixed results. Limitations Core stability is rarely the sole component of an athletic development programme, making it difficult to directly isolate its affect on athletic performance. The population biases of some studies of athletic performance also confound the results. Conclusions Targeted core stability training provides marginal benefits to athletic performance. Conflicting findings and the lack of a standardization for measurement of outcomes and training focused to improve core strength and stability pose difficulties. Because of this, further research targeted to determine this relationship is necessary to better understand how core strength and stability affect athletic performance. PMID:22784233

Characterization of airborne particles generated from metal active gas welding process.

PubMed

Guerreiro, C; Gomes, J F; Carvalho, P; Santos, T J G; Miranda, R M; Albuquerque, P

2014-05-01

This study is focused on the characterization of particles emitted in the metal active gas welding of carbon steel using mixture of Ar + CO2, and intends to analyze which are the main process parameters that influence the emission itself. It was found that the amount of emitted particles (measured by particle number and alveolar deposited surface area) are clearly dependent on the distance to the welding front and also on the main welding parameters, namely the current intensity and heat input in the welding process. The emission of airborne fine particles seems to increase with the current intensity as fume-formation rate does. When comparing the tested gas mixtures, higher emissions are observed for more oxidant mixtures, that is, mixtures with higher CO2 content, which result in higher arc stability. These mixtures originate higher concentrations of fine particles (as measured by number of particles by cm(3) of air) and higher values of alveolar deposited surface area of particles, thus resulting in a more severe worker's exposure.

Iowa interstate rest area stabilization ponds : Part I. Pond design, Part II: Feasibility of wind-powered aeration.

DOT National Transportation Integrated Search

1979-09-01

"This report is presented in two parts. Part I takes a new look at the design of rest area stabilization ponds after nearly 10 years'experience with some of the existing ponds and in the light of new design standards issued by Iowa DEQ. The Iowa DOT ...

Landslide and slope stability evaluation in the historical town of Kruja, Albania

NASA Astrophysics Data System (ADS)

Muceku, Y.; Korini, O.

2014-03-01

This paper describes landslides and slope stability evaluation in the urban area of Kruja, Albania. Kruja is a historical and heritage center, due to the existence of many important cultural monuments, including "Skanderbeg" castle and Bazaar square, etc. The urban area of Kruja has been affected by landslide effects, in the past and also the present. From this phenomenon many engineering objects such as buildings, roads, etc., are damaged and demolished. From engineering geological mapping at scale 1:5000 it is observed that many active landslides have dramatically increased in activity since the 1980s. The landslide types found in the studied area are earthslides, debris flow, as well as rockfall and rock rolling. Also, from field works and laboratory analysis, the slope stability of the whole urban area has been determined; for this purpose the studied zone is divided into stable and unstable areas, which helps to better understand mass movement activity as one of the most harmful hazards of geodynamic phenomena.

Landslides and slope stability evaluation in the historical town of Kruja, Albania

NASA Astrophysics Data System (ADS)

Muceku, Y.; Korini, O.

2013-07-01

This paper describes the landslides and slope stability evaluation in the urban area of Kruja town, Albania. Kruja is a~historical and heritage center, due to the existence of many important cultural monuments including Skanderbeg castle and Bazaar square etc. The urban area of Kruja town has been affected from the Landslides effects, in the past and also present. From this phenomenon many engineering objects such as buildings, roads etc. are damaged and demolished. From the engineering geological mapping at scale 1 : 5000 it is observed that many active landslides have dramatically increased in activity after 1980s. The landslide types found in the studied area are earth slides, debris flow, as well as rock fall and rock rolling. Also, from field works and laboratory analysis, the slope stability of whole urban areas has been determined; for this purpose the studied zone is divided into the stable and unstable areas, which helps to better understand the mass movement's activity as one of the most harmful hazards of the geodynamics' phenomena.

Membrane-based systems for carbon capture and hydrogen purification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berchtold, Kathryn A

2010-11-24

This presentation describes the activities being conducted at Los Alamos National Laboratory to develop carbon capture technologies for power systems. This work is aimed at continued development and demonstration of a membrane based pre- and post-combustion carbon capture technology and separation schemes. Our primary work entails the development and demonstration of an innovative membrane technology for pre-combustion capture of carbon dioxide that operates over a broad range of conditions relevant to the power industry while meeting the US DOE's Carbon Sequestration Program goals of 90% CO{sub 2} capture at less than a 10% increase in the cost of energy services.more » Separating and capturing carbon dioxide from mixed gas streams is a first and critical step in carbon sequestration. To be technically and economically viable, a successful separation method must be applicable to industrially relevant gas streams at realistic temperatures and pressures as well as be compatible with large gas volumes. Our project team is developing polymer membranes based on polybenzimidazole (PBI) chemistries that can purify hydrogen and capture CO{sub 2} at industrially relevant temperatures. Our primary objectives are to develop and demonstrate polymer-based membrane chemistries, structures, deployment platforms, and sealing technologies that achieve the critical combination of high selectivity, high permeability, chemical stability, and mechanical stability all at elevated temperatures (> 150 C) and packaged in a scalable, economically viable, high area density system amenable to incorporation into an advanced Integrated Gasification Combined-Cycle (IGCC) plant for pre-combustion CO{sub 2} capture. Stability requirements are focused on tolerance to the primary synthesis gas components and impurities at various locations in the IGCC process. Since the process stream compositions and conditions (temperature and pressure) vary throughout the IGCC process, the project is focused on the optimization of a technology that could be positioned upstream or downstream of one or more of the water-gas-shift reactors (WGSRs) or integrated with a WGSR.« less

Combined analytical and numerical approaches in Dynamic Stability analyses of engineering systems

NASA Astrophysics Data System (ADS)

Náprstek, Jiří

2015-03-01

Dynamic Stability is a widely studied area that has attracted many researchers from various disciplines. Although Dynamic Stability is usually associated with mechanics, theoretical physics or other natural and technical disciplines, it is also relevant to social, economic, and philosophical areas of our lives. Therefore, it is useful to occasionally highlight the general aspects of this amazing area, to present some relevant examples and to evaluate its position among the various branches of Rational Mechanics. From this perspective, the aim of this study is to present a brief review concerning the Dynamic Stability problem, its basic definitions and principles, important phenomena, research motivations and applications in engineering. The relationships with relevant systems that are prone to stability loss (encountered in other areas such as physics, other natural sciences and engineering) are also noted. The theoretical background, which is applicable to many disciplines, is presented. In this paper, the most frequently used Dynamic Stability analysis methods are presented in relation to individual dynamic systems that are widely discussed in various engineering branches. In particular, the Lyapunov function and exponent procedures, Routh-Hurwitz, Liénard, and other theorems are outlined together with demonstrations. The possibilities for analytical and numerical procedures are mentioned together with possible feedback from experimental research and testing. The strengths and shortcomings of these approaches are evaluated together with examples of their effective complementing of each other. The systems that are widely encountered in engineering are presented in the form of mathematical models. The analyses of their Dynamic Stability and post-critical behaviour are also presented. The stability limits, bifurcation points, quasi-periodic response processes and chaotic regimes are discussed. The limit cycle existence and stability are examined together with their separating roles as attractors and repulsers. Two levels of stability loss (recovery of the system is possible or final collapse is inevitable) as can be observed in softening systems are noted. Time-limited excitation and relevant transition effects (e.g., seismic excitation) are also discussed, together with the evaluation of possible system reliability improvement. The Dynamic Stability investigation of two degrees-of-freedom aero-elastic systems in a linear formulation using several approaches is briefly highlighted. Further systems modelling problems that arise in transport engineering are also outlined. A few hints for applications are given. Some open problems and possible future research strategies are outlined.

Thermal stability of black holes with arbitrary hairs

NASA Astrophysics Data System (ADS)

Sinha, Aloke Kumar

2018-02-01

We have derived the criteria for thermal stability of charged rotating black holes, for horizon areas that are large relative to the Planck area (in these dimensions). In this paper, we generalized it for black holes with arbitrary hairs. The derivation uses results of loop quantum gravity and equilibrium statistical mechanics of the grand canonical ensemble and there is no explicit use of classical spacetime geometry at all in this analysis. The assumption is that the mass of the black hole is a function of its horizon area and all the hairs. Our stability criteria are then tested in detail against some specific black holes, whose metrics provide us with explicit relations for the dependence of the mass on the area and other hairs of the black holes. This enables us to predict which of these black holes are expected to be thermally unstable under Hawking radiation.

Liquid lens enabling real-time focus and tilt compensation for optical image stabilization in camera modules

NASA Astrophysics Data System (ADS)

Simon, Eric; Craen, Pierre; Gaton, Hilario; Jacques-Sermet, Olivier; Laune, Frédéric; Legrand, Julien; Maillard, Mathieu; Tallaron, Nicolas; Verplanck, Nicolas; Berge, Bruno

2010-05-01

A new generation of liquid lenses based on electrowetting has been developed, using a multi-electrode design, enabling to induce optical tilt and focus corrections in the same component. The basic principle is to rely on a conical shape for supporting the liquid interface, the conical shape insuring a restoring force for the liquid liquid interface to come at the center position. The multi-electrode design enables to induce an average tilt of the liquid liquid interface when a bias voltage is applied to the different electrodes. This tilt is reversible, vanishing when voltage bias is cancelled. Possible application of this new lens component is the realization of miniature camera featuring auto-focus and optical image stabilization (OIS) without any mobile mechanical part. Experimental measurements of actual performances of liquid lens component will be presented : focus and tilt amplitude, residual optical wave front error and response time.

Optimization of Stabilization of Highway Embankment Slopes Using Driven Piles (Phase II – Development and Verification)

DOT National Transportation Integrated Search

2015-01-01

This study examines the feasibility of using driven piles to stabilize highway embankment slopes. The literature review showed that there has been significant research done concerning the lateral capacity of piles. This research tends to be focused o...

An Attributional Theory of Achievement Motivation and Emotion.

ERIC Educational Resources Information Center

Weiner, Bernard

1985-01-01

This article advances an attributional theory of motivation and emotion, with achievement strivings as the theoretical focus. Causes of success and failure share three common properties: locus, stability, and controllability. Stability of causes influences changes in expectancy of success. Expectancy and affect guide motivated behavior.…

Enhancing synchronization stability in a multi-area power grid

PubMed Central

Wang, Bing; Suzuki, Hideyuki; Aihara, Kazuyuki

2016-01-01

Maintaining a synchronous state of generators is of central importance to the normal operation of power grids, in which many networks are generally interconnected. In order to understand the condition under which the stability can be optimized, it is important to relate network stability with feedback control strategies as well as network structure. Here, we present a stability analysis on a multi-area power grid by relating it with several control strategies and topological design of network structure. We clarify the minimal feedback gain in the self-feedback control, and build the optimal communication network for the local and global control strategies. Finally, we consider relationship between the interconnection pattern and the synchronization stability; by optimizing the network interlinks, the obtained network shows better synchronization stability than the original network does, in particular, at a high power demand. Our analysis shows that interlinks between spatially distant nodes will improve the synchronization stability. The results seem unfeasible to be implemented in real systems but provide a potential guide for the design of stable power systems. PMID:27225708

Design of Perovskite Oxides as Anion-Intercalation-Type Electrodes for Supercapacitors: Cation Leaching Effect.

PubMed

Liu, Yu; Dinh, Jim; Tade, Moses O; Shao, Zongping

2016-09-14

Oxygen ions can be exploited as a charge carrier to effectively realize a new type of anion-intercalation supercapacitor. In this study, to get some useful guidelines for future materials development, we comparatively studied SrCoO3-δ (SC), Ba0.5Sr0.5Co0.8Fe0.2O3-δ (BSCF), and Co3O4 as electrodes in supercapacitors with aqueous alkaline electrolyte. The effect of interaction between the electrode materials with the alkaline solution was focused on the structure and specific surface area of the electrode material, and ultimately the electrochemical performance was emphasized. Both BSCF and SC were found to experience cation leaching in alkaline solution, resulting in an increase in the specific surface area of the material, but overleaching caused the damage of perovskite structure of BSCF. Barium leaching was more serious than strontium, and the cation leaching was component dependent. Although high initial capacitance was achieved for BSCF, it was not a good candidate as intercalation-type electrode for supercapacitor because of poor cycling stability from serious Ba(2+) and Sr(2+) leaching. Instead, SC was a favorable electrode candidate for practical use in supercapacitors due to its high capacity and proper cation leaching capacity, which brought beneficial effect on cycling stability. It is suggested that cation leaching effect should be seriously considered in the development of new perovskite materials as electrodes for supercapacitors.

Proxy-based accelerated discovery of Fischer–Tropsch catalysts† †Electronic supplementary information (ESI) available: Details of synthesis, analysis and testing, validation experiments for high-throughput XRD and gas treatment, details of statistical analysis and calculations, tabulation of synthesis parameters and XRD results, alternatives to Fig. 3 highlighting different data points, FTS testing results displayed graphically. See DOI: 10.1039/c4sc02116a Click here for additional data file.

PubMed Central

Boldrin, Paul; Gallagher, James R.; Combes, Gary B.; Enache, Dan I.; James, David; Ellis, Peter R.; Kelly, Gordon; Claridge, John B.

2015-01-01

Development of heterogeneous catalysts for complex reactions such as Fischer–Tropsch synthesis of fuels is hampered by difficult reaction conditions, slow characterisation techniques such as chemisorption and temperature-programmed reduction and the need for long term stability. High-throughput (HT) methods may help, but their use has until now focused on bespoke micro-reactors for direct measurements of activity and selectivity. These are specific to individual reactions and do not provide more fundamental information on the materials. Here we report using simpler HT characterisation techniques (XRD and TGA) along with ageing under Fischer–Tropsch reaction conditions to provide information analogous to metal surface area, degree of reduction and thousands of hours of stability testing time for hundreds of samples per month. The use of this method allowed the identification of a series of highly stable, high surface area catalysts promoted by Mg and Ru. In an advance over traditional multichannel HT reactors, the chemical and structural information we obtain on the materials allows us to identify the structural effects of the promoters and their effects on the modes of deactivation observed. PMID:29560180

Thermal Examination of an Orbiting Cryogenic Fuel Depot

NASA Technical Reports Server (NTRS)

Hull, Patrick V.; Canfield, Steven L.; Carrington, Connie; Fikes, John

2002-01-01

For many years NASA has been interested in the storage and transfer of cryogenic fuels in space. Lunar, L2 and other chemical propulsive space vehicle missions now have staged refueling needs that a fuel depot would satisfy. The depot considered is located in lower earth orbit. Many considerations must go into designing and building such a station. Multi-layer insulation systems, thermal shielding and low conductive structural supports are the principal means of protecting the system from excessive heat loss due to boiloff. This study focuses on the thermal losses associated with storing LH2 in a passively cooled fuel depot in a lower earth equatorial orbit. The corresponding examination looks at several configurations of the fuel depot. An analytical model has been developed to determine the thermal advantages and disadvantages of three different fuel depot configurations. Each of the systems consists of three Boeing rocket bodies arranged in various configurations. The first two configurations are gravity gradient stabilized while the third one is a spin-stabilized concept. Each concept was chosen for self-righting capabilities as well as the fuel settling capabilities, however the purpose of this paper is to prove which of the three concepts is the most efficient passively cooled system. The specific areas to be discussed are the heating time from the fusion temperature to the vaporization temperature and the amount of boiloff for a specific number of orbits. Each of the previous points is compared using various sun exposed surface areas of the tanks.

STE thrust chamber technology: Main injector technology program and nozzle Advanced Development Program (ADP)

NASA Technical Reports Server (NTRS)

1993-01-01

The purpose of the STME Main Injector Program was to enhance the technology base for the large-scale main injector-combustor system of oxygen-hydrogen booster engines in the areas of combustion efficiency, chamber heating rates, and combustion stability. The initial task of the Main Injector Program, focused on analysis and theoretical predictions using existing models, was complemented by the design, fabrication, and test at MSFC of a subscale calorimetric, 40,000-pound thrust class, axisymmetric thrust chamber operating at approximately 2,250 psi and a 7:1 expansion ratio. Test results were used to further define combustion stability bounds, combustion efficiency, and heating rates using a large injector scale similar to the Pratt & Whitney (P&W) STME main injector design configuration including the tangential entry swirl coaxial injection elements. The subscale combustion data was used to verify and refine analytical modeling simulation and extend the database range to guide the design of the large-scale system main injector. The subscale injector design incorporated fuel and oxidizer flow area control features which could be varied; this allowed testing of several design points so that the STME conditions could be bracketed. The subscale injector design also incorporated high-reliability and low-cost fabrication techniques such as a one-piece electrical discharged machined (EDMed) interpropellant plate. Both subscale and large-scale injectors incorporated outer row injector elements with scarfed tip features to allow evaluation of reduced heating rates to the combustion chamber.

Edge fires drive the shape and stability of tropical forests.

PubMed

Hébert-Dufresne, Laurent; Pellegrini, Adam F A; Bhat, Uttam; Redner, Sidney; Pacala, Stephen W; Berdahl, Andrew M

2018-06-01

In tropical regions, fires propagate readily in grasslands but typically consume only edges of forest patches. Thus, forest patches grow due to tree propagation and shrink by fires in surrounding grasslands. The interplay between these competing edge effects is unknown, but critical in determining the shape and stability of individual forest patches, as well the landscape-level spatial distribution and stability of forests. We analyze high-resolution remote-sensing data from protected Brazilian Cerrado areas and find that forest shapes obey a robust perimeter-area scaling relation across climatic zones. We explain this scaling by introducing a heterogeneous fire propagation model of tropical forest-grassland ecotones. Deviations from this perimeter-area relation determine the stability of individual forest patches. At a larger scale, our model predicts that the relative rates of tree growth due to propagative expansion and long-distance seed dispersal determine whether collapse of regional-scale tree cover is continuous or discontinuous as fire frequency changes. © 2018 The Authors. Ecology Letters published by CNRS and John Wiley & Sons Ltd.

A new synthesis route to high surface area sol gel bioactive glass through alcohol washing

PubMed Central

M. Mukundan, Lakshmi; Nirmal, Remya; Vaikkath, Dhanesh; Nair, Prabha D.

2013-01-01

Bioactive glass is one of the widely used bone repair material due to its unique properties like osteoconductivity, osteoinductivity and biodegradability. In this study bioactive glass is prepared by the sol gel process and stabilized by a novel method that involves a solvent instead of the conventional calcinations process. This study represents the first attempt to use this method for the stabilization of bioactive glass. The bioactive glass stabilized by this ethanol washing process was characterized for its physicochemical and biomimetic property in comparison with similar composition of calcined bioactive glass. The compositional similarity of the two stabilized glass powders was confirmed by spectroscopic and thermogravimetric analysis. Other physicochemical characterizations together with the cell culture studies with L929 fibroblast cells and bone marrow mesenchymal stem cells proved that the stabilization was achieved with the retention of its inherent bioactive potential. However an increase in the surface area of the glass powder was obtained as a result of this ethanol washing process and this add up to the success of the study. Hence the present study exhibits a promising route for high surface area bioactive glass for increasing biomimicity. PMID:23512012

Design of an unified chassis controller for rollover prevention, manoeuvrability and lateral stability

NASA Astrophysics Data System (ADS)

Yoon, Jangyeol; Yim, Seongjin; Cho, Wanki; Koo, Bongyeong; Yi, Kyongsu

2010-11-01

This paper describes a unified chassis control (UCC) strategy to prevent vehicle rollover and improve both manoeuvrability and lateral stability. Since previous researches on rollover prevention are only focused on the reduction of lateral acceleration, the manoeuvrability and lateral stability cannot be guaranteed. For this reason, it is necessary to design a UCC controller to prevent rollover and improve lateral stability by integrating electronic stability control, active front steering and continuous damping control. This integration is performed through switching among several control modes and a simulation is performed to validate the proposed method. Simulation results indicate that a significant improvement in rollover prevention, manoeuvrability and lateral stability can be expected from the proposed UCC system.

Cognition as a Dynamic System: Principles from Embodiment

ERIC Educational Resources Information Center

Smith, Linda B.

2005-01-01

Traditional approaches to cognitive development concentrate on the stability of cognition and explain that stability via concepts segregated from perceiving acting. A dynamic systems approach in contrast focuses on the self-organization of behavior in tasks. This article uses recent results concerning the embodiment of cognition to argue for a…

Contributions of COMT Val[superscript 158]Met to Cognitive Stability and Flexibility in Infancy

ERIC Educational Resources Information Center

Markant, Julie; Cicchetti, Dante; Hetzel, Susan; Thomas, Kathleen M.

2014-01-01

Adaptive behavior requires focusing on relevant tasks while remaining sensitive to novel information. In adult studies of cognitive control, cognitive stability involves maintaining robust cognitive representations while cognitive flexibility involves updating of representations in response to novel information. Previous adult research has shown…

Aggregate Stability of Tropical Soils Under Long-Term Eucalyptus Cultivation

USDA-ARS?s Scientific Manuscript database

Eucalyptus cultivation has increased in all Brazilian regions. Despite the large amount of cultivated area, little is known about how this kind of management system affects soil properties, mainly the aggregate stability. Aggregate stability analyses have proved to be a sensitive tool to measure soi...

[Stability of home based care arrangements for people with dementia : Development of a consensus definition of stability using expert focus groups].

PubMed

von Kutzleben, Milena; Köhler, Kerstin; Dreyer, Jan; Holle, Bernhard; Roes, Martina

2017-04-01

The majority of people with dementia in Germany live at home. These informal care arrangements, which are mostly coordinated by informal carers, are the backbone of home-based dementia care. Creating and maintaining stability is an underlying theme in informal care; however, a definition of the complex phenomenon of 'stability' in this context is still lacking. The aim was to develop a working definition of stability of home-based care arrangements for people with dementia, which can be applied in current and future research projects at the German Center for Neurodegenerative Diseases in Witten (DZNE Witten) and others. Ensuing from prior research a preliminary version of the definition was formulated. This definition was discussed in a focus group of scientific experts with expertise in dementia research and care (n = 8). After data analysis using content analysis, the definition was revised during a scientific colloquium (n = 18) and a consensus was finally reached. There were four major themes which were considered by the experts as being relevant for the definition of stability: (1) creating and maintaining stability as a continuous adaptation process, (2) a qualitative component of stability, (3) persons with dementia and informal carers as pivotal players and (4) transitions to residential care. The working definition introduced in this article reflects the authors' understanding of the phenomenon of stability of home-based care arrangements for people with dementia. In times of increasing need for evidence-based interventions it is necessary to develop elaborated definitions of complex phenomena in order to be able to systematically evaluate the efficacy of interventions on the basis of a common understanding.

Stability Behavior and Thermodynamic States of Iron and Manganese in Sandy Soil Aquifer, Manukan Island, Malaysia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lin, Chin Yik, E-mail: cy_lin_ars@hotmail.com; Abdullah, Mohd. Harun; Musta, Baba

2011-03-15

A total of 20 soil samples were collected from 10 boreholes constructed in the low lying area, which included ancillary samples taken from the high elevation area. Redox processes were investigated in the soil as well as groundwater in the shallow groundwater aquifer of Manukan Island, Sabah, Malaysia. Groundwater samples (n = 10) from each boreholes were also collected in the low lying area to understand the concentrations and behaviors of Fe and Mn in the dissolved state. This study strives to obtain a general understanding of the stability behaviors on Fe and Mn at the upper unsaturated and themore » lower-saturated soil horizons in the low lying area of Manukan Island as these elements usually play a major role in the redox chemistry of the shallow groundwater. Thermodynamic calculations using PHREEQC showed that the groundwater samples in the study area are oversaturated with respect to goethite, hematite, Fe(OH){sub 3} and undersaturated with respect to manganite and pyrochroite. Low concentrations of Fe and Mn in the groundwater might be probably due to the lack of minerals of iron and manganese oxides, which exist in the sandy aquifer. In fact, high organic matters that present in the unsaturated horizon are believed to be responsible for the high Mn content in the soil. It was observed that the soil samples collected from high elevation area (BK) comprises considerable amount of Fe in both unsaturated (6675.87 mg/kg) and saturated horizons (31440.49 mg/kg) compared to the low Fe content in the low lying area. Based on the stability diagram, the groundwater composition lies within the stability field for Mn{sup 2+} and Fe{sup 2+} under suboxic condition and very close to the FeS/Fe{sup 2+} stability boundary. This study also shows that both pH and Eh values comprise a strong negative value thus suggesting that the redox potential is inversely dependent on the changes of pH.« less

Stability of a modified Peaceman–Rachford method for the paraxial Helmholtz equation on adaptive grids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sheng, Qin, E-mail: Qin_Sheng@baylor.edu; Sun, Hai-wei, E-mail: hsun@umac.mo

This study concerns the asymptotic stability of an eikonal, or ray, transformation based Peaceman–Rachford splitting method for solving the paraxial Helmholtz equation with high wave numbers. Arbitrary nonuniform grids are considered in transverse and beam propagation directions. The differential equation targeted has been used for modeling propagations of high intensity laser pulses over a long distance without diffractions. Self-focusing of high intensity beams may be balanced with the de-focusing effect of created ionized plasma channel in the situation, and applications of grid adaptations are frequently essential. It is shown rigorously that the fully discretized oscillation-free decomposition method on arbitrary adaptivemore » grids is asymptotically stable with a stability index one. Simulation experiments are carried out to illustrate our concern and conclusions.« less

Rotating apparatus for isoelectric focusing

NASA Technical Reports Server (NTRS)

Bier, Milan (Inventor)

1986-01-01

This disclosure is directed to an isoelectric focusing apparatus, wherein stabilization of the fluid containing the isolated proteins is achieved by carrying out the separation in a rotating cylinder with the separation cavity of the cylinder being segmented by means of filter elements. The filter elements are constituted of a material offering some degree of resistance to fluid convection, but allowing relatively free and unhindered passage of current and transport of proteins. The combined effect of segmentation and rotation has been found to be superior to either segmentation or rotation alone in maintaining the stability of the migrated fractions.

Infrastructure stability surveillance with high resolution InSAR

NASA Astrophysics Data System (ADS)

Balz, Timo; Düring, Ralf

2017-02-01

The construction of new infrastructure in largely unknown and difficult environments, as it is necessary for the construction of the New Silk Road, can lead to a decreased stability along the construction site, leading to an increase in landslide risk and deformation caused by surface motion. This generally requires a thorough pre-analysis and consecutive surveillance of the deformation patterns to ensure the stability and safety of the infrastructure projects. Interferometric SAR (InSAR) and the derived techniques of multi-baseline InSAR are very powerful tools for a large area observation of surface deformation patterns. With InSAR and deriver techniques, the topographic height and the surface motion can be estimated for large areas, making it an ideal tool for supporting the planning, construction, and safety surveillance of new infrastructure elements in remote areas.

Stabilizing eroding streambanks in sand drift areas of the Lake States.

Treesearch

Edward A. Hansen

1968-01-01

Banks are stabilized to protect adjacent high-value items such as cabins and campgrounds, or to reduce reservoir or lake sedimentation rates. Also, bank stabilization is undertaken as one part of fish habitat improvement programs. Rock rip-rap is the best material for bank stabilization in most cases. It does not deteriorate with time and it blends in well with the...

30 CFR 817.114 - Revegetation: Mulching and other soil stabilizing practices.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Revegetation: Mulching and other soil... STANDARDS-UNDERGROUND MINING ACTIVITIES § 817.114 Revegetation: Mulching and other soil stabilizing practices. Suitable mulch and other soil stabilizing practices shall be used on all areas that have been...

30 CFR 817.114 - Revegetation: Mulching and other soil stabilizing practices.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Revegetation: Mulching and other soil... STANDARDS-UNDERGROUND MINING ACTIVITIES § 817.114 Revegetation: Mulching and other soil stabilizing practices. Suitable mulch and other soil stabilizing practices shall be used on all areas that have been...

30 CFR 816.114 - Revegetation: Mulching and other soil stabilizing practices.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Revegetation: Mulching and other soil... STANDARDS-SURFACE MINING ACTIVITIES § 816.114 Revegetation: Mulching and other soil stabilizing practices. Suitable mulch and other soil stabilizing practices shall be used on all areas that have been regraded and...

30 CFR 817.114 - Revegetation: Mulching and other soil stabilizing practices.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Revegetation: Mulching and other soil... STANDARDS-UNDERGROUND MINING ACTIVITIES § 817.114 Revegetation: Mulching and other soil stabilizing practices. Suitable mulch and other soil stabilizing practices shall be used on all areas that have been...

30 CFR 816.114 - Revegetation: Mulching and other soil stabilizing practices.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Revegetation: Mulching and other soil... STANDARDS-SURFACE MINING ACTIVITIES § 816.114 Revegetation: Mulching and other soil stabilizing practices. Suitable mulch and other soil stabilizing practices shall be used on all areas that have been regraded and...

30 CFR 816.114 - Revegetation: Mulching and other soil stabilizing practices.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Revegetation: Mulching and other soil... STANDARDS-SURFACE MINING ACTIVITIES § 816.114 Revegetation: Mulching and other soil stabilizing practices. Suitable mulch and other soil stabilizing practices shall be used on all areas that have been regraded and...

30 CFR 817.114 - Revegetation: Mulching and other soil stabilizing practices.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Revegetation: Mulching and other soil... STANDARDS-UNDERGROUND MINING ACTIVITIES § 817.114 Revegetation: Mulching and other soil stabilizing practices. Suitable mulch and other soil stabilizing practices shall be used on all areas that have been...

30 CFR 816.114 - Revegetation: Mulching and other soil stabilizing practices.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Revegetation: Mulching and other soil... STANDARDS-SURFACE MINING ACTIVITIES § 816.114 Revegetation: Mulching and other soil stabilizing practices. Suitable mulch and other soil stabilizing practices shall be used on all areas that have been regraded and...

30 CFR 817.114 - Revegetation: Mulching and other soil stabilizing practices.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Revegetation: Mulching and other soil... STANDARDS-UNDERGROUND MINING ACTIVITIES § 817.114 Revegetation: Mulching and other soil stabilizing practices. Suitable mulch and other soil stabilizing practices shall be used on all areas that have been...

30 CFR 816.114 - Revegetation: Mulching and other soil stabilizing practices.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Revegetation: Mulching and other soil... STANDARDS-SURFACE MINING ACTIVITIES § 816.114 Revegetation: Mulching and other soil stabilizing practices. Suitable mulch and other soil stabilizing practices shall be used on all areas that have been regraded and...

7 CFR 1980.451 - Filing and processing applications.

Code of Federal Regulations, 2010 CFR

2010-01-01

... categories, and their point scores, are: (A) Project will contribute to the overall economic stability of the... points). (B) Project will contribute to the overall economic stability of the project area and will...'s economy (20 points). (C) Project will contribute to the overall economic stability of the project...

Mediterranean sponges from shallow subtidal rocky reefs: Cystoseira canopy vs barren grounds

NASA Astrophysics Data System (ADS)

Costa, Gabriele; Bertolino, Marco; Pinna, Stefania; Bonaviri, Chiara; Padiglia, Andrea; Zinni, Matteo; Pronzato, Roberto; Manconi, Renata

2018-07-01

Porifera richness was investigated in Cystoseira canopies vs barren grounds considering different substrates at 6 areas in the Central-Western Mediterranean Sea. In total 31 sponge taxa were recorded at 2-7 m depth and the sponge community structure and composition were characterized by a notably low richness with 25 taxa in the Cystoseira forest and 15 in the barren area. As for the sponge habitus, the massive sponges were dominant in both facies, whereas encrusting, and cavity dwelling sponges were found in higher numbers in the Cystoseira forest. Results revealed that rocky substrata seem to play a key role in driving the sponge community composition and diversity in both facies. In this work we explore the role of Cystoseira canopy as a suitable facies for sponges. Sponge assemblages were persistent, strongly resilient in space occupation and consequently support stability in both facies. Some species seem to be pre-adapted to live under the sub-optimal conditions of the barren grounds, i.e. the absence of the Cystoseira fronds shelter. This focus on sponge successful eco-etological performances in 'submarine deserts' such as barren areas shows features as shown in a few other sessile benthic invertebrates.

Characteristics of extreme dust events observed over two urban areas in Iran

NASA Astrophysics Data System (ADS)

Bidokhti, Abbas-Ali A.; Gharaylou, Maryam; Pegahfar, Nafiseh; Sabetghadam, Samaneh; Rezazadeh, Maryam

2016-03-01

Determination of dust loading in the atmosphere is important not only from the public health point of view, but also for regional climate changes. The present study focuses on the characteristics of two major dust events for two urban areas in Iran, Kermanshah and Tehran, over the period of 4 years from 2006 to 2009. To detect extreme dust outbreaks, various datasets including synoptic data, dust concentration, reanalysis data and numerical results of WRF and HYSPLIT models were used. The weather maps demonstrate that for these events dusts are mainly generated when wind velocity is high and humidity is low in the lower troposphere and the region is under the influence of a thermal low. The event lasts until the atmospheric stability prevails and the surface wind speed weakens. The thermal low nature of the synoptic conditions of these major events is also responsible for deep boundary layer development with its thermals affecting the vertical dust flux over the region. Trajectory studies show that the dust events originated from deserts in Iraq and Syria and transported towards Iran. The main distinction between the two types of mobilizations seems to affect the dust concentrations in the Tehran urban area.

Application of seismic interferometric migration for shallow seismic high precision data processing: A case study in the Shenhu area

NASA Astrophysics Data System (ADS)

Wei, Jia; Liu, Huaishan; Xing, Lei; Du, Dong

2018-02-01

The stability of submarine geological structures has a crucial influence on the construction of offshore engineering projects and the exploitation of seabed resources. Marine geologists should possess a detailed understanding of common submarine geological hazards. Current marine seismic exploration methods are based on the most effective detection technologies. Therefore, current research focuses on improving the resolution and precision of shallow stratum structure detection methods. In this article, the feasibility of shallow seismic structure imaging is assessed by building a complex model, and differences between the seismic interferometry imaging method and the traditional imaging method are discussed. The imaging effect of the model is better for shallow layers than for deep layers because coherent noise produced by this method can result in an unsatisfactory imaging effect for deep layers. The seismic interference method has certain advantages for geological structural imaging of shallow submarine strata, which indicates continuous horizontal events, a high resolution, a clear fault, and an obvious structure boundary. The effects of the actual data applied to the Shenhu area can fully illustrate the advantages of the method. Thus, this method has the potential to provide new insights for shallow submarine strata imaging in the area.

Stabilization of the As-contaminated soil from the metal mining areas in Korea.

PubMed

Ko, Myoung-Soo; Kim, Ju-Yong; Bang, Sunbeak; Lee, Jin-Soo; Ko, Ju-In; Kim, Kyoung-Woong

2012-01-01

The stabilization efficiencies of arsenic (As) in contaminated soil were evaluated using various additives such as limestone, steel mill slag, granular ferric hydroxide (GFH), and mine sludge collected from an acid mine drainage treatment system. The soil samples were collected from the Chungyang area, where abandoned Au-Ag mines are located. Toxicity characteristic leaching procedure, synthetic precipitation leaching procedure, sequential extraction analysis, aqua regia digestion, cation exchange capacity, loss on ignition, and particle size distribution were conducted to assess the physical and chemical characteristics of highly arsenic-contaminated soils. The total concentrations of arsenic in the Chungyang area soil ranged up to 145 mg/kg. After the stabilization tests, the removal percentages of dissolved As(III) and As(V) were found to differ from the additives employed. Approximately 80 and 40% of the As(V) and As(III), respectively, were removed with the use of steel mill slag. The addition of limestone had a lesser effect on the removal of arsenic from solution. However, more than 99% of arsenic was removed from solution within 24 h when using GFH and mine sludge, with similar results observed when the contaminated soils were stabilized using GFH and mine sludge. These results suggested that GFH and mine sludge may play a significant role on the arsenic stabilization. Moreover, this result showed that mine sludge can be used as a suitable additive for the stabilization of arsenic.

Evaluating the oxidative, photothermal and electrical stability of colloidal nanocrystal solids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Law, Matt

2016-02-16

IV-VI quantum dot (QD) solids are a novel class of granular electronic materials with great technological potential (e.g., in photodetectors, field-effect transistors (FETs), and solar cells), but their oxidative and thermal instability present a barrier to practical applications [1]. Poor stability is a fundamental issue facing many nanoscale materials due to high surface area and surface energy. Basic studies are needed to elucidate the most important mechanisms of degradation and develop robust countermeasures if QD materials are to become technologically important. This project determined the degradation mechanisms of IV-VI QD solids (primarily PbSe and PbS) and introduced new chemical strategiesmore » to drastically improve their performance, stability, and operating lifetimes [2-5]. Our approach was based on (1) detailed testing of QD thin film materials (principally FETs and solar cells) as a function of oxidative and thermal stress, and (2) the use of organic and inorganic approaches to link the QDs into strongly electronically coupled, high-mobility films, prevent their oxidation, and eliminate internal degrees of freedom that lead to film instability and degradation in response to electrical and thermal stress. Stability against oxidation and thermal degradation was the major focus of this project. We have evaluated the stability of QD thin films and interfaces at temperatures less than 100°C (the regime most relevant to solar and transistor applications). Low-temperature oxidation and sintering of QD films have been investigated using optical absorption spectroscopy, Fourier transform infrared spectroscopy (FTIR), current-voltage scanning of transistors and solar cells, X-ray photoelectron spectroscopy, and scanning Kelvin probe microscopy (SKPM). SKPM was used to map the potential profiles of operating QD FETs and solar cells as a function of bias and illumination, which provides detailed information on how the work functions, potential drops and electric field within these devices determine device operation, and set the stage for future studies targeted at understanding and preventing device failure. We pursued two strategies to fabricate QD films with stable electrical characteristics: (1) the use of robust molecular surface ligands [2], and (2) “matrix engineering,” i.e., infilling the QD solid with metal oxide or metal sulfide matrices by low-temperature atomic layer deposition (ALD) to passivate surface states, prevent oxidation, lock the QDs into position, inhibit diffusion, and tune the height and width of the inter-QD potential barriers that govern charge transport [5,6]. Poor stability is a common feature of nanoscale electronic materials, yet stability is all too rarely the focus of basic research. Fundamental studies are therefore needed to elucidate the most important mechanisms of degradation and develop simple yet effective countermeasures. By revealing both how QD solids degrade in response to environmental stresses (oxidative, photothermal, and electric) and how to prevent this degradation, the project has greatly improved our ability to develop stable, high-performance QD materials for real-world applications.« less

The Long, Hard Journey: Expanding the Use of NASA Data and Models for Sustainable Development Planning Around the World

NASA Technical Reports Server (NTRS)

Khan, Maudood; Limaye, Ashutosh; Crosson, William; Unal, Alper; Kete, nancy; Rickman, Douglas

2009-01-01

In 2007, the National Research Council's committee on Extending Observations and Research Results to Practical Applications recommended that NASA's Applied Science Program (ASP) directly engage with a broader community of users - not just federal agencies. Soon afterwards, scientists at the NASA Marshall Space Flight Center began discussions on a collaborative research project with EMBARQ - the World Resource Institute's Center for Sustainable Transport. The discussions initially focused on how best to utilize satellite observations and atmospheric models for assessing the impact of a proposed transportation project on land use and air quality. Discussions exposed the participants to a broad spectrum of science and policy challenges that these diverse organizations face on a routine basis. It brought into clear focus the need for an observation-modeling system that will allow a proactive approach towards development planning, and the fact that satellite systems do not always provide the spatial and temporal resolution useful for urban-scale applications, underscoring the need for earth system models to bridge this gap. Realizing the significant risk that unplanned urbanization and climate change pose to the social and functional stability of large cities, both organizations decided to expand the scope of their preliminary discussion to include water resources and agriculture. A pilot project, funded by NASA ASP, EMBARQ and Istanbul Technical University focused on quantifying the magnitude and extent of urbanization in Istanbul, and analyzed the combined effect of urbanization and projected climate change on local climate, air quality, and its consequent effects on agricultural productivity. Preliminary results show that Istanbul has undergone a significant amount of Land Use/Land Cover change over the past two decades. While some forested areas have been lost to urban-landscapes, urbanization has mostly occurred over former croplands due to the fact that in contrast to forested areas, croplands have flat terrain, making them a more attractive target for conversion to urban land. The reduction in land area for agricultural and increase in temperature has reduced agricultural production in the vicinity of the city. The United Nations expects the world population to reach 9.2 billion by 2050. Most of this increase will be absorbed by countries that are least able to sustain it. Rapid economic growth is likely to continue and will require massive infrastructure investments. If not properly managed, the magnitude and extent of these initiatives will overwhelm sensitive ecosystems around the world. Successful relationships such as the one described here are critically important if we are to stabilize the threatened ecosystems on which human systems ultimately rely. The challenges, needs, culture, and operating environment of development planning organizations are fundamentally different from a research organization. An appreciation of these differences is a prerequisite for any successful collaboration.

One-dimensional terahertz imaging of surfactant-stabilized dodecane-brine emulsion

NASA Astrophysics Data System (ADS)

Nickel, Daniel Vincent

Terahertz line-images of surfactant-stabilized dodecane(C12H 26)-brine emulsions are obtained by translating the emulsified region through the focus of a terahertz time-domain spectrometer, capturing a time-domain waveform at each vertical position. From these images, relative dodecane content, emulsion size, and stability can be extracted to evaluate the efficacy of the surfactant in solvating the dodecane. In addition, the images provide insight into the dynamics of concentrated emulsions after mixing.

Safe distance car-following model including backward-looking and its stability analysis

NASA Astrophysics Data System (ADS)

Yang, Da; Jin, Peter Jing; Pu, Yun; Ran, Bin

2013-03-01

The focus of this paper is the car-following behavior including backward-looking, simply called the bi-directional looking car-following behavior. This study is motivated by the potential changes of the physical properties of traffic flow caused by the fast developing intelligent transportation system (ITS), especially the new connected vehicle technology. Existing studies on this topic focused on general motors (GM) models and optimal velocity (OV) models. The safe distance car-following model, Gipps' model, which is more widely used in practice have not drawn too much attention in the bi-directional looking context. This paper explores the property of the bi-directional looking extension of Gipps' safe distance model. The stability condition of the proposed model is derived using the linear stability theory and is verified using numerical simulations. The impacts of the driver and vehicle characteristics appeared in the proposed model on the traffic flow stability are also investigated. It is found that taking into account the backward-looking effect in car-following has three types of effect on traffic flow: stabilizing, destabilizing and producing non-physical phenomenon. This conclusion is more sophisticated than the study results based on the OV bi-directional looking car-following models. Moreover, the drivers who have the smaller reaction time or the larger additional delay and think the other vehicles have larger maximum decelerations can stabilize traffic flow.

Woody Vegetation on Levees? - Research Experiences and Design Suggestions

NASA Astrophysics Data System (ADS)

Lammeranner, Walter

2013-04-01

Recent flood events in Austria have reawakened practical and scientific interest in the stability of levees. One focus amongst others has been taken on the relationship between vegetation and levee stability with special reference to the role of woody plants. The effects of woody plants are undoubtedly manifold: On the one hand they can potentially have a negative influence and endanger levees, which is why many guidelines ban woody vegetation to preserve stability, visual inspection and unhindered flood-fight access. On the other hand woody vegetation can have several positive impacts on soil stability and which effects prevail depends largely on types and characteristics of plants. This shows how controversially woody plants on levees can be discussed and the strong need for further research in this field. In order to obtain new insights and widen horizons for this controversial issue, a research project carried out by the Institute of Soil Bioengineering and Landscape Construction - at the University of Natural Resources and Life Sciences, Vienna - was launched. This project deals with several aspects of effects of woody plants have on levees and focuses particularly on shrubby woody plants. The examined vegetation type is a dense stand of willows - Purple-Willows (Salix purpurea L.) - commonly used for stabilization of river embankments. The proposed contribution discusses the gained results with reference to levee stability and existing levee vegetation guidelines and gives design suggestions for compatible woody vegetation on levees.

PoPMuSiC 2.1: a web server for the estimation of protein stability changes upon mutation and sequence optimality.

PubMed

Dehouck, Yves; Kwasigroch, Jean Marc; Gilis, Dimitri; Rooman, Marianne

2011-05-13

The rational design of modified proteins with controlled stability is of extreme importance in a whole range of applications, notably in the biotechnological and environmental areas, where proteins are used for their catalytic or other functional activities. Future breakthroughs in medical research may also be expected from an improved understanding of the effect of naturally occurring disease-causing mutations on the molecular level. PoPMuSiC-2.1 is a web server that predicts the thermodynamic stability changes caused by single site mutations in proteins, using a linear combination of statistical potentials whose coefficients depend on the solvent accessibility of the mutated residue. PoPMuSiC presents good prediction performances (correlation coefficient of 0.8 between predicted and measured stability changes, in cross validation, after exclusion of 10% outliers). It is moreover very fast, allowing the prediction of the stability changes resulting from all possible mutations in a medium size protein in less than a minute. This unique functionality is user-friendly implemented in PoPMuSiC and is particularly easy to exploit. Another new functionality of our server concerns the estimation of the optimality of each amino acid in the sequence, with respect to the stability of the structure. It may be used to detect structural weaknesses, i.e. clusters of non-optimal residues, which represent particularly interesting sites for introducing targeted mutations. This sequence optimality data is also expected to have significant implications in the prediction and the analysis of particular structural or functional protein regions. To illustrate the interest of this new functionality, we apply it to a dataset of known catalytic sites, and show that a much larger than average concentration of structural weaknesses is detected, quantifying how these sites have been optimized for function rather than stability. The freely available PoPMuSiC-2.1 web server is highly useful for identifying very rapidly a list of possibly relevant mutations with the desired stability properties, on which subsequent experimental studies can be focused. It can also be used to detect sequence regions corresponding to structural weaknesses, which could be functionally important or structurally delicate regions, with obvious applications in rational protein design.

Are all temperate lakes eutrophying in a warmer world?

NASA Astrophysics Data System (ADS)

Paltsev, A.; Creed, I. F.

2017-12-01

Freshwater lakes are at risk of eutrophication due to climate change and intensification of human activities on the planet. In relatively undisturbed areas of the temperate forest biome, lakes are "sentinels" of the effects of rising temperatures. We hypothesise that rising temperatures are driving a shift from nutrient-poor oligotrophic states to nutrient-rich eutrophic states. To test this hypothesis, we examined a time series of satellite based chlorophyll-a (a proxy of algal biomass) of 12,000+ lakes over 30 years in the Canadian portion of the Laurentian Great Lakes basin. From the time series, non-stationary trends (detected by Mann-Kendall analysis) and stationary cycles (revealed through Morlet wavelet analysis) were removed, and the standard deviation (SD) of the remaining residuals was used as an indicator of lake stability. Four classes of lake stability were identified: (1) stable (SD is consistently low); (2) destabilizing (SD increases over time); (3) unstable (SD is consistently high); and (4) stabilizing lakes (SD decreases over time). Stable lakes were either oligotrophic or eutrophic indicating the presence of two stable states in the region. Destabilizing lakes were shifting from oligotrophic to lakes with a higher trophic status (indicating eutrophication), unstable lakes were mostly mesotrophic, and stabilizing lakes were shifting from eutrophic to the lakes with lower trophic status (indicating oligotrophication). In contrast to common expectations, while many lakes (2142) were shifting from oligotrophic to eutrophic states, more lakes (3199) were showing the opposite trend and shifting from eutrophic to oligotrophic states. This finding reveals a complexity of lake responses to rising temperatures and the need to improve understanding of why some lakes shift while others do not. Future work is focused on exploring the interactive effects of global, regional, and local drivers of lake trophic states.

Design of Single-Site Photocatalyst using Metal-Organic Framework as Matrix.

PubMed

Wen, Meicheng; Mori, Kohsuke; Kuwahara, Yasutaka; An, Taicheng; Yamashita, Hiromi

2018-05-14

Single-site photocatalyst generally displays excellent photocatalytic activtiy and considerable high stability as compared to homogeneous catalytic system. A rational structural design of single-site photocatalyst with isolated, uniform and spatially separated active sites in a given solid is of prime importance to achieve high photocatalytic activity. Intense attentions have been focused on the engineering and fabrication of single-site photocatalys by using porous materials as platform. Metal-organic frameworks (MOFs) hold great potential for the design and fabrication of single-site photocatalysts due to their remarkable porosity, ultrahigh surface area, extraordinary tailorability and significant diversity. MOFs can provide abundant number of binding sites for anchoring active sites, result in significant enhancement of photocatalytic performance. In this focus review, the development of single-site MOF photocatalysts that perform in important and challenging chemical redox reaction such as photocatalytic water splitting, photocatalytic CO₂ conversion and organic transformations is summarized thoroughly. The successful strategies applied for the construction of single-site MOF photocatalysts and major challenge toward practical application was summarized and pointed out, respectively. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Controlling in situ crystallization of pharmaceutical particles within the spray dryer.

PubMed

Woo, Meng Wai; Lee, May Ginn; Shakiba, Soroush; Mansouri, Shahnaz

2017-11-01

Simultaneous solidification and in situ crystallization (or partial crystallization) of droplets within the drying chamber are commonly encountered in the spray drying of pharmaceuticals. The crystallinity developed will determine the functionality of the powder and its stability during storage. This review discusses strategies that can be used to control the in situ crystallization process. Areas covered: The premise of the strategies discussed focuses on the manipulation of the droplet drying rate relative to the timescale of crystallization. This can be undertaken by the control of the spray drying operation, by the use of volatile materials and by the inclusion of additives. Several predictive approaches for in situ crystallization control and new spray dryer configuration strategies are further discussed. Expert opinion: Most reports, hitherto, have focused on the crystallinity of the spray dried material or the development of crystallinity during storage. More mechanistic understanding of the in situ crystallization process during spray drying is required to guide product formulation trials. The key challenge will be in adapting the mechanistic approach to the myriad possible formulations in the pharmaceutical industry.

Supersaturation and crystallization: non-equilibrium dynamics of amorphous solid dispersions for oral drug delivery.

PubMed

Kawakami, Kohsaku

2017-06-01

Amorphous solid dispersions (ASDs) are one of the key formulation technologies that aid the development of poorly soluble candidates. However, their dynamic behaviors, including dissolution and crystallization processes, are still full of mystery. Further understanding of these processes should enhance their wider use. Areas covered: The first part of this review describes the current understanding of the dissolution of ASDs, where phase separation behavior is frequently involved and attempts to develop appropriate dissolution tests to achieve an in vitro-in vivo correlation are examined. The second part of this review discusses crystallization of the drug molecule with the eventual aim of establishing an accelerated testing protocol for predicting its physical stability. Expert opinion: The phase separation behavior from the supersaturated state during the dissolution test must be understood, and its relevance to the oral absorption behavior needs to be clarified. Research efforts should focus on the differences between the phase behavior in in vitro and in vivo situations. Initiation time of the crystallization was shown to be predicted only from storage and glass transition temperatures. This finding should encourage the establishment of testing protocol of the physical stability of ASDs.

Long-Term Delivery of Protein Therapeutics

PubMed Central

Vaishya, Ravi; Khurana, Varun; Patel, Sulabh; Mitra, Ashim K

2015-01-01

Introduction Proteins are effective biotherapetics with applications in diverse ailments. Despite being specific and potent, their full clinical potential has not yet been realized. This can be attributed to short half-lives, complex structures, poor in vivo stability, low permeability frequent parenteral administrations and poor adherence to treatment in chronic diseases. A sustained release system, providing controlled release of proteins, may overcome many of these limitations. Areas covered This review focuses on recent development in approaches, especially polymer-based formulations, which can provide therapeutic levels of proteins over extended periods. Advances in particulate, gel based formulations and novel approaches for extended protein delivery are discussed. Emphasis is placed on dosage form, method of preparation, mechanism of release and stability of biotherapeutics. Expert opinion Substantial advancements have been made in the field of extended protein delivery via various polymer-based formulations over last decade despite the unique delivery-related challenges posed by protein biologics. A number of injectable sustained-release formulations have reached market. However, therapeutic application of proteins is still hampered by delivery related issues. A large number of protein molecules are under clinical trials and hence there is an urgent need to develop new methods to deliver these highly potent biologics. PMID:25251334

The Russian Federation Islamic Republic of Dagestan: Curricular Decentralization, Social Cohesion, and Stability

ERIC Educational Resources Information Center

Eaton, Jana Sackman

2005-01-01

This article focuses on the curricular decentralization-sociopolitical stability nexus in the predominantly Muslim Russian Federation Republic of Dagestan, adjacent to war-torn Chechnya. Concomitant with the metamorphoses taking place in the economic and political sectors of society is the overhaul of institutionalized education. A major reform…

Chapter 13: Tools for analysis

Treesearch

William Elliot; Kevin Hyde; Lee MacDonald; James McKean

2007-01-01

This chapter presents a synthesis of current computer modeling tools that are, or could be, adopted for use in evaluating the cumulative watershed effects of fuel management. The chapter focuses on runoff, soil erosion and slope stability predictive tools. Readers should refer to chapters on soil erosion and stability for more detailed information on the physical...

Temporal Stability of Strength-Based Assessments: Test-Retest Reliability of Student and Teacher Reports

ERIC Educational Resources Information Center

Romer, Natalie; Merrell, Kenneth W.

2013-01-01

This study focused on evaluating the temporal stability of self-reported and teacher-reported perceptions of students' social and emotional skills and assets. We used a test-retest reliability procedure over repeated administrations of the child, adolescent, and teacher versions of the "Social-Emotional Assets and Resilience Scales".…

Effects of dominant material properties on the stability and transport of TiO2 nanoparticles and carbon nanotubes in aquatic environment: From synthesis to fate

EPA Science Inventory

Recently, increasing studies have focused on the environment stability, transport, and fate of the anthropogenic nanomaterials in the environment, which contributes to the understanding of the potential risks when released. However, applying nanomaterials from different manufactu...

Stability and Change in Positive Development during Young Adulthood

ERIC Educational Resources Information Center

Hawkins, Mary T.; Letcher, Primrose; Sanson, Ann; O'Connor, Meredith; Toumbourou, John W.; Olsson, Craig

2011-01-01

Calls have been made for a greater focus on successful development and how positive functioning can be conceptualized in theory and empirical research. Drawing on a large Australian community sample (N = 890; 61.7% female), this article examines the structure and stability of positive development at two time points during young adulthood.…

A Politically Liberal Conception of Formal Education in a Developing Democracy

ERIC Educational Resources Information Center

Çelik, Rasit

2016-01-01

As discussed by John Rawls, in a well-ordered society, a public political culture's wide educational role bears the primary responsibility for developing reasonable individuals for the stability of a politically liberal society. Rawlsian scholars have also focused on the stability and enhancement of developed liberal democratic societies by means…

Longitudinal Stability and Control Characteristics from a Flight Investigation of a Cruciform Canard Missile Configuration Having an Exposed Wing-canard Area Ratio of 16:1

NASA Technical Reports Server (NTRS)

Moul, Martin T; Wineman, Andrew R

1952-01-01

A flight investigation has been made to determine the longitudinal stability and control characteristics of a 60 0 delta-wing-canard missile configuration with an exposed wing-canard area ratio of 16:1. The results presented include the longitudinal stability derivatives, control effectiveness, and drag characteristics for a Mach number range of 0.75 to 1.80 and are compared with the results of a similar configuration having larger 6ontrols. Stability characteristics are also presented from the flights of an interdigitated canard configuration at a Mach number of 2.08 and a wing-body configuration at Mach numbers of 1.25 to 1.45. The stability derivatives varied gradually with Mach number with the exception of the damping-in-pitch derivative. Aerodynamic damping in pitch decreased to a minimum at a Mach number of 1.0 3, then increased to a peak value at a Mach number of 1.26 followed by a gradual decrease at higher Mach numbers. The aerodynamic-center location of the in-line canard configuration shifted rearward 13 percent of the mean aerodynamic chord at transonic speeds. The pitching-moment curve slope was 25 percent greater for the model having no canards than for the in-line configuration. No large effects of interdigitation were noted in the stability derivatives. Pitching effectiveness of the in-line configuration was maintained throughout the Mach number range. A comparison of the stability and control characteristics of two canard configurations having different area controls showed that decreasing the control area 44 percent decreased the pitching effectiveness proportionally, shifted the aerodynamic-center location rearward 9 to 14 percent of the mean aerodynamic chord, and reduced the total hinge moments required for 10 trimmed flight about 50 percent at transonic speeds.

Stabilization and reconstruction operations: the role of the US Army Veterinary Corps.

PubMed

Smith, John C

2007-01-01

Stabilization and reconstruction operations in failed or failing states are vital to US security interests. These operations require a bottom-up approach, focusing on the population as the strategic center of gravity. This bottom-up approach must address the population's basic needs, as defined by Dr Abraham Maslow's hierarchy of needs, and provide a long-term means of self-sufficiency, rather than creating an "aid dependent economy." Focusing operations on agricultural projects provides relief from donor dependency, stimulates economic growth, and thwarts the power of spoilers. US Army Veterinary Corps personnel provide essential services ensuring the procurement of safe and wholesome subsistence and provision of medical care to government-owned animals. Veterinary Corps officers are also uniquely qualified to design and implement agricultural stabilization and reconstruction programs in conjunction with host-state ministries and agencies across the full range of military operations. Early, sustained engagement by veterinarians stimulates agricultural productivity, improves animal and human health, directly supports the population's hierarchy of needs on all levels, and accelerates stabilization operations by reducing the population's susceptibility to spoilers.

Quantum-dot-sensitized solar cells.

PubMed

Rühle, Sven; Shalom, Menny; Zaban, Arie

2010-08-02

Quantum-dot-sensitized solar cells (QDSCs) are a promising low-cost alternative to existing photovoltaic technologies such as crystalline silicon and thin inorganic films. The absorption spectrum of quantum dots (QDs) can be tailored by controlling their size, and QDs can be produced by low-cost methods. Nanostructures such as mesoporous films, nanorods, nanowires, nanotubes and nanosheets with high microscopic surface area, redox electrolytes and solid-state hole conductors are borrowed from standard dye-sensitized solar cells (DSCs) to fabricate electron conductor/QD monolayer/hole conductor junctions with high optical absorbance. Herein we focus on recent developments in the field of mono- and polydisperse QDSCs. Stability issues are adressed, coating methods are presented, performance is reviewed and special emphasis is given to the importance of energy-level alignment to increase the light to electric power conversion efficiency.

Recent progress on magnetic iron oxide nanoparticles: synthesis, surface functional strategies and biomedical applications

PubMed Central

Wu, Wei; Wu, Zhaohui; Yu, Taekyung; Jiang, Changzhong; Kim, Woo-Sik

2015-01-01

This review focuses on the recent development and various strategies in the preparation, microstructure, and magnetic properties of bare and surface functionalized iron oxide nanoparticles (IONPs); their corresponding biological application was also discussed. In order to implement the practical in vivo or in vitro applications, the IONPs must have combined properties of high magnetic saturation, stability, biocompatibility, and interactive functions at the surface. Moreover, the surface of IONPs could be modified by organic materials or inorganic materials, such as polymers, biomolecules, silica, metals, etc. The new functionalized strategies, problems and major challenges, along with the current directions for the synthesis, surface functionalization and bioapplication of IONPs, are considered. Finally, some future trends and the prospects in these research areas are also discussed. PMID:27877761

Biomedical Properties Study of Modified Chitosan Nanoparticles for Drug Delivery Systems

NASA Astrophysics Data System (ADS)

Saboktakin, Mohammad Reza

2013-09-01

The purpose of this review is to discuss and summarize some of the interesting findings and applications of modified chitosan (MCS) and their derivatives in different areas of drug delivery. This review highlights the important applications of MCS in the design of various novel delivery systems like liposomes, microspheres, microcapsules, and nanoparticles. In addition to their well-known effects on drug solubility and dissolution, bioavailability, safety, and stability, their uses as recipients in drug formulation are also discussed. This review also focuses on various factors influencing inclusion complex formation because an understanding of the same is necessary for proper handling of these versatile materials. Some important considerations in selecting MCS in drug formulation such as their commercial availability, regulatory status, and patent status are also summarized.

RF transient analysis and stabilization of the phase and energy of the proposed PIP-II LINAC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Edelen, J. P.; Chase, B. E.

This paper describes a recent effort to develop and benchmark a simulation tool for the analysis of RF transients and their compensation in an H- linear accelerator. Existing tools in this area either focus on electron LINACs or lack fundamental details about the LLRF system that are necessary to provide realistic performance estimates. In our paper we begin with a discussion of our computational models followed by benchmarking with existing beam-dynamics codes and measured data. We then analyze the effect of RF transients and their compensation in the PIP-II LINAC, followed by an analysis of calibration errors and how amore » Newton’s Method based feedback scheme can be used to regulate the beam energy to within the specified limits.« less

Pattern Analysis in Social Networks with Dynamic Connections

NASA Astrophysics Data System (ADS)

Wu, Yu; Zhang, Yu

In this paper, we explore how decentralized local interactions of autonomous agents in a network relate to collective behaviors. Most existing work in this area models social network in which agent relations are fixed; instead, we focus on dynamic social networks where agents can rationally adjust their neighborhoods based on their individual interests. We propose a new connection evaluation rule called the Highest Weighted Reward (HWR) rule, with which agents dynamically choose their neighbors in order to maximize their own utilities based on the rewards from previous interactions. Our experiments show that in the 2-action pure coordination game, our system will stabilize to a clustering state where all relationships in the network are rewarded with the optimal payoff. Our experiments also reveal additional interesting patterns in the network.

Reconceptualizing Learning as a Dynamical System.

ERIC Educational Resources Information Center

Ennis, Catherine D.

1992-01-01

Dynamical systems theory can increase our understanding of the constantly evolving learning process. Current research using experimental and interpretive paradigms focuses on describing the attractors and constraints stabilizing the educational process. Dynamical systems theory focuses attention on critical junctures in the learning process as…

Endeavour to simplify the frustrated concept of protein-ammonium family ionic liquid interactions.

PubMed

Jha, Indrani; Venkatesu, Pannuru

2015-08-28

The large amount of attention earned by ionic liquids (ILs) in the various physical and chemical sciences has been attributed to their unique, designer nature. In the past few years, the role of ILs in protein folding/unfolding has been rapidly growing. In light of the increasing importance of ILs, it is desirable to systematize the ion effects on protein properties such as structure stability, activity and enantioselectivity. Various studies available in the literature show ILs as a potential solvent medium for many enzymatic reactions, as well as in various protein folding/unfolding studies. Various reviews by many researchers focus on the synthesis, application and general properties of the ILs, however a review focussing on the effect of various ILs on the activity, structure and stability of proteins is still missing. Also, according to the best of our knowledge there is no single review available throughout the literature that focuses on the effect of the same family of ILs on different proteins. Therefore, it is a priority to obtain complete knowledge of the biomolecules, particularly amino acids (AAs) and proteins in a particular IL family. The focus of the present perspective is to investigate the performance of a list of proteins and protein model compounds in the presence of ammonium-based ILs. This perspective presents a survey of all the key developments from the available reports and also our past and present experience related to proteins and ammonium-based ILs. Additionally, we have tried to put the available information in chronological order in most of the cases. The use of ammonium family ILs as a co-solvent for various proteins model compounds and proteins has been outlined. This perspective can act as a barometer for reckoning the various advancements made in this field and can also galvanize further investigation of various untouched aspects of this research area.

Developmental Origins of Cognitive Vulnerabilities to Depression: Review of Processes Contributing to Stability and Change Across Time

PubMed Central

Hankin, Benjamin L.; Oppenheimer, Caroline; Jenness, Jessica; Barrocas, Andreas; Shapero, Benjamin G.; Goldband, Jessica

2011-01-01

Cognitive theories of depression have been shown to be potent predictors of future increases in depressive symptoms and disorder in children, adolescents, and adults. This article focuses on potential developmental origins of the main cognitive vulnerabilities, including dysfunctional attitudes, negative cognitive style, and rumination. We selectively review processes and factors that have been hypothesized to contribute to the emergence and stabilization of these cognitive risk factors. This review focuses on genetic factors, temperament, parents and peers as salient interpersonal influences, and stressful life events. We end with suggestions for future theory development and research. In particular, we emphasize the need for additional conceptual and empirical work integrating these disparate processes together into a coherent, developmental psychopathological model, and we highlight the coexistence of both stability and change in the development of cognitive vulnerabilities to depression across the lifespan. PMID:19827008

SINMAP Modeling of an active landslide area in the Swabian Alb

NASA Astrophysics Data System (ADS)

Terhorst, Birgit; Jaeger, Daniel

2015-04-01

Landslides are a common hazard in German low mountain areas such as the Swabian Alb. As areas of former landslides are highly prone to secondary movements, this study aims to assess the susceptibility for landslide hazard around Mössingen-Öschingen, a region consistently affected by landslides during the last decades. Based on the history and development of mass movements and a detailed geomorphological map, slope stability was calculated using SINMAP (Stability Index Mapping). SINMAP (Pack et al., 1998; Tarboton, 1997) is based on the "infinite slope stability model" by Hammond et al. (1992) and Montgomery and Dietrich (1994) describing the ratio of slope stabilizing factors (e.g. cohesion) and slope destabilizing factors (e.g. gravitation) on a slip surface parallel to the slope. Most input parameters are determined by the relief and therefore, can be calculated from a digital terrain model (DTM, resolution 5 m). Based on the local morphology and geology, a total of 10 'calibration regions', each with similar hydrogeological characteristics, were defined. Further input parameters were: Shear strength via friction angle (Phi), cohesion (C) and hydraulic conductivity (T/R). The data was obtained from soil mechanical assessments and field/laboratory analyses. As a result, a specific stability index is calculated, describing the susceptibility of a slope movement. In a first step, the 'topographic wetness index' (derived from catchment area, slope gradient and hydraulic conductivity) was calculated. Results show several preferred (natural) drainage channels with generally higher water saturations in morphological depressions. Several of them can be linked to the location of damaged houses in the settlement area on the lower slope. The SINMAP calculation clearly revealed the impermeable Callovian clay layers as most prone to slope movements. A comparison of the susceptibility map with slide masses which were mapped during a field survey showed generally good agreements. This was in particular true for the slopes of the "Landhaussiedlung", a small settlement area east of Mössingen-Öschingen. In the uphill areas, a large landslide was triggered on June 3rd, 2013, mainly caused by heavy rainfalls during the days before. The scarp/slip surface was situated in the Callovian clay layers and in an area which was shown as susceptible for slope movements by the SINMAP model earlier Terhorst and Kreja (2009). The movement processes reactivated an old slide mass, which reached the outermost parts of the settlement area and damaged the densely built-up underground of the Landhaussiedlung. Although no house was destroyed completely by the slide mass, the induced pressure caused severe damages, rendering the buildings uninhabitable and leading to the evacuation of the Landhaussiedlung. The results show, that the modeling provided a solid identification of the vulnerable slope areas. The recent landslide area is almost completely situated in a region modeled as vulnerable for slope movements. Therefore, the landslide event of 2013 practically validated the susceptibility map. On the base of solid data and under consideration of detailed and differentiated information, SINMAP is a powerful tool for the assessment of susceptibilities for translational slides. Hammond, C., Hall, D., Miller, S., Swetik, P., 1992. Level I Stability Analysis (LISA) documentation for version 2.0. General Technical Report, INT-285. U.S. Deptartment of Agriculture, Forest Service, Intermountain Research Station, Ogden. Montgomery, D.R., Dietrich, W.E., 1994. A Physically Based Model for the Topographic Control on Shallow Landsliding. Water Resources Research, 30(4), 1153-1171. Pack, R.T., Tarboton, D.G., Goodwin, C.N., 1998. The SINMAP approach to terrain stability mapping, 8th Congress of the International Association of Engineering Geology, Vancouver, Canada, pp. 8. Tarboton, D.G., 1997. A new method for the determination of flow directions and upslope areas in grid digital elevation models. Water Resources Research, 33(2), 309-319. Terhorst, B., Kreja, R., 2009. Slope stability modelling with SINMAP in a settlement area of the Swabian Alb. Landslides, 6(4), 309-319.

Estimating life expectancies for US small areas: a regression framework

NASA Astrophysics Data System (ADS)

Congdon, Peter

2014-01-01

Analysis of area mortality variations and estimation of area life tables raise methodological questions relevant to assessing spatial clustering, and socioeconomic inequalities in mortality. Existing small area analyses of US life expectancy variation generally adopt ad hoc amalgamations of counties to alleviate potential instability of mortality rates involved in deriving life tables, and use conventional life table analysis which takes no account of correlated mortality for adjacent areas or ages. The alternative strategy here uses structured random effects methods that recognize correlations between adjacent ages and areas, and allows retention of the original county boundaries. This strategy generalizes to include effects of area category (e.g. poverty status, ethnic mix), allowing estimation of life tables according to area category, and providing additional stabilization of estimated life table functions. This approach is used here to estimate stabilized mortality rates, derive life expectancies in US counties, and assess trends in clustering and in inequality according to county poverty category.

Surface science studies on titania for solar fuel applications

NASA Astrophysics Data System (ADS)

Hadsell, Courtney Sara Mathews

Titanium dioxide (titania) is a well-studied material for various applications including but not limited to, paint, sunscreen, pharmaceuticals and solar cell applications (photocatalysis.) It can be found in three main crystal forms; rutile, anatase, and brookite and this work will focus on the anatase form which has been heavily studied for its potential in dye sensitized solar cells (DSSCs.) I propose that aqueous and photo dye stability can be improved by taking special care to the exposed surface of anatase. Additionally, the theoretical maximum open circuit voltage of a DSSC is dependent upon which surface is exposed to the electrolyte. Previous works in this area have not been rigorous with respect to the surface and morphology of titania being used. Standard synthesis techniques of anatase lead to a crystal that generally has 94% of the titania (101) surface exposed, and the other 6% is the higher energy (001) surface. The (101) surface has 5 & 6-fold coordinated titania whereas the (001) surface only has 5-fold (under) coordinated titania. This under-coordination leads to enhanced reactivity of the (001) surface which has been demonstrated by dissassociative adsorption of water, and catalysis applications. Much theoretical work has focused on the minority (001) surface because up until recently synthesizing anatase with enhanced exposure of the (001) surface has been difficult. The initial materials for this study will be multilayer titania nanotubes (TiNTs) and nanosheets (TiNS) which have been previously characterized by my predecessor. The TiNTs and TiNS have 100% exposed (001)-like surface. Both of these materials show enhanced stability of phosphonated dye binding as compared to the current standard of anatase nanoparticles (NPs) however, due to their limited thermal stability the potential of incorporating the TiNTs and TiNSs into devices has been eliminated in this study. To overcome the device limitations I will synthesis a novel titania nanotile (ntile) material which will have enhancement of the (001) surface while an increased thermal stability allowing for incorporation into a device. These ntiles will be created from a hydrothermal hydrolysis reaction between titanium n-butoxide (TiBuOx) and hydrofluoric acid (HF.) I will characterize this novel material and demonstrate the enhanced dye binding as well as the device capabilities.

Robust exponential stability of uncertain delayed neural networks with stochastic perturbation and impulse effects.

PubMed

Huang, Tingwen; Li, Chuandong; Duan, Shukai; Starzyk, Janusz A

2012-06-01

This paper focuses on the hybrid effects of parameter uncertainty, stochastic perturbation, and impulses on global stability of delayed neural networks. By using the Ito formula, Lyapunov function, and Halanay inequality, we established several mean-square stability criteria from which we can estimate the feasible bounds of impulses, provided that parameter uncertainty and stochastic perturbations are well-constrained. Moreover, the present method can also be applied to general differential systems with stochastic perturbation and impulses.

Structural stability of coplanar 1T-2H superlattice MoS2 under high energy electron beam.

PubMed

Reshmi, S; Akshaya, M V; Satpati, Biswarup; Basu, Palash Kumar; Bhattacharjee, K

2018-05-18

Coplanar heterojunctions composed of van der Waals layered materials with different structural polymorphs have drawn immense interest recently due to low contact resistance and high carrier injection rate owing to low Schottky barrier height. Present research has largely focused on efficient exfoliation of these layered materials and their restacking to achieve better performances. We present here a microwave assisted easy, fast and efficient route to induce high concentration of metallic 1T phase in the original 2H matrix of exfoliated MoS 2 layers and thus facilitating the formation of a 1T-2H coplanar superlattice phase. High resolution transmission electron microscopy (HRTEM) investigations reveal formation of highly crystalline 1T-2H hybridized structure with sharp interface and disclose the evidence of surface ripplocations within the same exfoliated layer of MoS 2 . In this work, the structural stability of 1T-2H superlattice phase during HRTEM measurements under an electron beam of energy 300 keV is reported. This structural stability could be either associated to the change in electronic configuration due to induction of the restacked hybridized phase with 1T- and 2H-regions or to the formation of the surface ripplocations. Surface ripplocations can act as an additional source of scattering centers to the electron beam and also it is possible that a pulse train of propagating ripplocations can sweep out the defects via interaction from specific areas of MoS 2 sheets.

Structural stability of coplanar 1T-2H superlattice MoS2 under high energy electron beam

NASA Astrophysics Data System (ADS)

Reshmi, S.; Akshaya, M. V.; Satpati, Biswarup; Basu, Palash Kumar; Bhattacharjee, K.

2018-05-01

Coplanar heterojunctions composed of van der Waals layered materials with different structural polymorphs have drawn immense interest recently due to low contact resistance and high carrier injection rate owing to low Schottky barrier height. Present research has largely focused on efficient exfoliation of these layered materials and their restacking to achieve better performances. We present here a microwave assisted easy, fast and efficient route to induce high concentration of metallic 1T phase in the original 2H matrix of exfoliated MoS2 layers and thus facilitating the formation of a 1T-2H coplanar superlattice phase. High resolution transmission electron microscopy (HRTEM) investigations reveal formation of highly crystalline 1T-2H hybridized structure with sharp interface and disclose the evidence of surface ripplocations within the same exfoliated layer of MoS2. In this work, the structural stability of 1T-2H superlattice phase during HRTEM measurements under an electron beam of energy 300 keV is reported. This structural stability could be either associated to the change in electronic configuration due to induction of the restacked hybridized phase with 1T- and 2H-regions or to the formation of the surface ripplocations. Surface ripplocations can act as an additional source of scattering centers to the electron beam and also it is possible that a pulse train of propagating ripplocations can sweep out the defects via interaction from specific areas of MoS2 sheets.

Gender and the Stability of Same-Sex and Different-Sex Relationships Among Young Adults.

PubMed

Joyner, Kara; Manning, Wendy; Bogle, Ryan

2017-12-01

Most research on the stability of adult relationships has focused on coresidential (cohabiting or married) unions and estimates rates of dissolution for the period of coresidence. Studies examining how the stability of coresidential unions differs by sex composition have typically found that same-sex female couples have higher rates of dissolution than same-sex male couples and different-sex couples. We argue that the more elevated rates of dissolution for same-sex female couples are a by-product of the focus on coresidential unions. We use data from the National Longitudinal Study of Adolescent to Adult Health to compare rates of dissolution based on the total duration of romantic and sexual relationships for same-sex male couples, same-sex female couples, and different-sex couples. Results from hazard models that track the stability of young adult relationships from the time they are formed demonstrate that male couples have substantially higher dissolution rates than female couples and different-sex couples. Results based on models restricted to the period of coresidence corroborate the counterintuitive finding from earlier studies that female couples have the highest rates of dissolving coresidential unions. This study underlines the importance of comparisons between these couple types for a better understanding of the role that institutions and gender play in the stability of contemporary relationships.

Assessment of Walking Stability of Elderly by Means of Nonlinear Time-Series Analysis and Simple Accelerometry

NASA Astrophysics Data System (ADS)

Ohtaki, Yasuaki; Arif, Muhammad; Suzuki, Akihiro; Fujita, Kazuki; Inooka, Hikaru; Nagatomi, Ryoichi; Tsuji, Ichiro

This study presents an assessment of walking stability in elderly people, focusing on local dynamic stability of walking. Its main objectives were to propose a technique to quantify local dynamic stability using nonlinear time-series analyses and a portable instrument, and to investigate their reliability in revealing the efficacy of an exercise training intervention for elderly people for improvement of walking stability. The method measured three-dimensional acceleration of the upper body, and computation of Lyapunov exponents, thereby directly quantifying the local stability of the dynamic system. Straight level walking of young and elderly subjects was investigated in the experimental study. We compared Lyapunov exponents of young and the elderly subjects, and of groups before and after the exercise intervention. Experimental results demonstrated that the exercise intervention improved local dynamic stability of walking. The proposed method was useful in revealing effects and efficacies of the exercise intervention for elderly people.

Midterm Stability Evaluation of Wide-area Power System by using Synchronized Phasor Measurements

NASA Astrophysics Data System (ADS)

Ota, Yutaka; Ukai, Hiroyuki; Nakamura, Koichi; Fujita, Hideki

In recent years, the PMU (Phasor Measurement Unit) receives a great deal of attention as a synchronized measurement system of power systems. Synchronized phasor angles obtained by the PMU provide the effective information for evaluating the stability of a bulk power system. The aspect of instability phenomena during midterm tends to be more complicated, and the stability analysis using the synchronized phasor measurements is significant in order to keep a complicated power system stable. This paper proposes a midterm stability evaluation method of the wide-area power system by using the synchronized phasor measurements. By clustering and aggregating the power system to some coherent groups, the step-out is effectively predicted on the basis of the two-machine equivalent power system model. The midterm stability of a longitudinal power system model of Japanese 60Hz systems constructed by the PSA, which is a hybrid-type power system simulator, is practically evaluated using the proposed method.

Physically-based slope stability modelling and parameter sensitivity: a case study in the Quitite and Papagaio catchments, Rio de Janeiro, Brazil

NASA Astrophysics Data System (ADS)

de Lima Neves Seefelder, Carolina; Mergili, Martin

2016-04-01

We use the software tools r.slope.stability and TRIGRS to produce factor of safety and slope failure susceptibility maps for the Quitite and Papagaio catchments, Rio de Janeiro, Brazil. The key objective of the work consists in exploring the sensitivity of the geotechnical (r.slope.stability) and geohydraulic (TRIGRS) parameterization on the model outcomes in order to define suitable parameterization strategies for future slope stability modelling. The two landslide-prone catchments Quitite and Papagaio together cover an area of 4.4 km², extending between 12 and 995 m a.s.l. The study area is dominated by granitic bedrock and soil depths of 1-3 m. Ranges of geotechnical and geohydraulic parameters are derived from literature values. A landslide inventory related to a rainfall event in 1996 (250 mm in 48 hours) is used for model evaluation. We attempt to identify those combinations of effective cohesion and effective internal friction angle yielding the best correspondence with the observed landslide release areas in terms of the area under the ROC Curve (AUCROC), and in terms of the fraction of the area affected by the release of landslides. Thereby we test multiple parameter combinations within defined ranges to derive the slope failure susceptibility (fraction of tested parameter combinations yielding a factor of safety smaller than 1). We use the tool r.slope.stability (comparing the infinite slope stability model and an ellipsoid-based sliding surface model) to test and to optimize the geotechnical parameters, and TRIGRS (a coupled hydraulic-infinite slope stability model) to explore the sensitivity of the model results to the geohydraulic parameters. The model performance in terms of AUCROC is insensitive to the variation of the geotechnical parameterization within much of the tested ranges. Assuming fully saturated soils, r.slope.stability produces rather conservative predictions, whereby the results yielded with the sliding surface model are more conservative than those yielded with the infinite slope stability model. The sensitivity of AUCROC to variations in the geohydraulic parameters remains small as long as the calculated degree of saturation of the soils is sufficient to result in the prediction of a significant amount of landslide release pixels. Due to the poor sensitivity of AUCROC to variations of the geotechnical and geohydraulic parameters it is hard to optimize the parameters by means of statistics. Instead, the results produced with many different combinations of parameters correspond reasonably well with the distribution of the observed landslide release areas, even though they vary considerably in terms of their conservativeness. Considering the uncertainty inherent in all geotechnical and geohydraulic data, and the impossibility to capture the spatial distribution of the parameters by means of laboratory tests in sufficient detail, we conclude that landslide susceptibility maps yielded by catchment-scale physically-based models should not be interpreted in absolute terms. Building on the assumption that our findings are generally valid, we suggest that efforts to develop better strategies for dealing with the uncertainties in the spatial variation of the key parameters should be given priority in future slope stability modelling efforts.

Trends and stability of inland fishery resources in Japanese lakes: introduction of exotic piscivores as a driver.

PubMed

Matsuzaki, Shin-ichiro S; Kadoya, Taku

2015-07-01

Although many studies have focused on marine resources, few studies have considered the resources of inland fisheries. Inland fishery resources are typically either monitored on the basis of catch data alone or are not assessed quantitatively at all, despite their social, economic, and ecological importance. Because freshwater ecosystems have been severely degraded by human activities, evaluating the trends and current status of fishery resources and assessing their drivers are urgent tasks. We compiled long-term data on the annual catch, fishing effort, and fishing power of 23 Japanese lakes, using two sets of government statistics that date back to the 1950s, which were previously neglected because of the large number of missing values. Using Bayesian state-space models, we examined the trajectories of the catch per unit effort (CPUE) of entire communities, considering changes in fishing effort and fishing power, and quantified both changes in the CPUE over the 10-, 20-, and 30-year periods preceding 2008 and the temporal detrended stability of the CPUE over the three periods. We also investigated the relationships among the CPUE changes and stability, anthropogenic drivers, and lake morphometric characteristics. The CPUE declined in 17, 19, and 15 of the 23 lakes over the past 10-, 20-, and 30-year periods, respectively. Our macroecological analyses demonstrate that the functional group richness of exotic piscivores was the most important predictor of changes in the CPUE among the drivers we considered. The stability of the CPUE was positively related to lake area; larger lakes have more stable CPUE. The functional group richness of exotic piscivores also negatively affected the stability of the CPUE. The effect of overfishing was considered to be small because both fishing effort and power declined in almost all of the lakes. Thus, our findings suggest that increasing exotic piscivore species may diminish the resources and their stability, particularly in Japanese lakes where native piscivores are rare. This might lead to a substantial decline in ecosystem services. Our study highlights the importance of assessing inland fishery resources in a comprehensive manner and the need for restoration strategies to mitigate the effects of exotic piscivores.

Disentangling Stability, Variability and Adaptability in Human Performance: Focus on the Interplay between Local Variance and Serial Correlation

ERIC Educational Resources Information Center

Torre, Kjerstin; Balasubramaniam, Ramesh

2011-01-01

We address the complex relationship between the stability, variability, and adaptability of psychological systems by decomposing the global variance of serial performance into two independent parts: the local variance (LV) and the serial correlation structure. For two time series with equal LV, the presence of persistent long-range correlations…

An Evaluation Method of Words Tendency Depending on Time-Series Variation and Its Improvements.

ERIC Educational Resources Information Center

Atlam, El-Sayed; Okada, Makoto; Shishibori, Masami; Aoe, Jun-ichi

2002-01-01

Discussion of word frequency and keywords in text focuses on a method to estimate automatically the stability classes that indicate a word's popularity with time-series variations based on the frequency change in past electronic text data. Compares the evaluation of decision tree stability class results with manual classification results.…

Better Homes and Families: Housing Markets and Young Couple Stability in Sweden

ERIC Educational Resources Information Center

Lauster, Nathanael T.

2008-01-01

I model the relationship between aspects of the housing market influenced by housing policy and couple stability for cohabiting couples in Sweden. Using data on 3,851 cohabiting couples obtained from the Swedish Family Survey of 1992, I examine the effects of housing market characteristics on couple outcomes. I focus on three housing variables,…

A novel adaptive finite time controller for bilateral teleoperation system

NASA Astrophysics Data System (ADS)

Wang, Ziwei; Chen, Zhang; Liang, Bin; Zhang, Bo

2018-03-01

Most bilateral teleoperation researches focus on the system stability within time-delays. However, practical teleoperation tasks require high performances besides system stability, such as convergence rate and accuracy. This paper investigates bilateral teleoperation controller design with transient performances. To ensure the transient performances and system stability simultaneously, an adaptive non-singular fast terminal mode controller is proposed to achieve practical finite-time stability considering system uncertainties and time delays. In addition, a novel switching scheme is introduced, in which way the singularity problem of conventional terminal sliding manifold is avoided. Finally, numerical simulations demonstrate the effectiveness and validity of the proposed method.

A dedicated superbend x-ray microdiffraction beamline for materials, geo-, and environmental sciences at the advanced light source.

PubMed

Kunz, Martin; Tamura, Nobumichi; Chen, Kai; MacDowell, Alastair A; Celestre, Richard S; Church, Matthew M; Fakra, Sirine; Domning, Edward E; Glossinger, James M; Kirschman, Jonathan L; Morrison, Gregory Y; Plate, Dave W; Smith, Brian V; Warwick, Tony; Yashchuk, Valeriy V; Padmore, Howard A; Ustundag, Ersan

2009-03-01

A new facility for microdiffraction strain measurements and microfluorescence mapping has been built on beamline 12.3.2 at the advanced light source of the Lawrence Berkeley National Laboratory. This beamline benefits from the hard x-radiation generated by a 6 T superconducting bending magnet (superbend). This provides a hard x-ray spectrum from 5 to 22 keV and a flux within a 1 microm spot of approximately 5x10(9) photons/s (0.1% bandwidth at 8 keV). The radiation is relayed from the superbend source to a focus in the experimental hutch by a toroidal mirror. The focus spot is tailored by two pairs of adjustable slits, which serve as secondary source point. Inside the lead hutch, a pair of Kirkpatrick-Baez (KB) mirrors placed in a vacuum tank refocuses the secondary slit source onto the sample position. A new KB-bending mechanism with active temperature stabilization allows for more reproducible and stable mirror bending and thus mirror focusing. Focus spots around 1 microm are routinely achieved and allow a variety of experiments, which have in common the need of spatial resolution. The effective spatial resolution (approximately 0.2 microm) is limited by a convolution of beam size, scan-stage resolution, and stage stability. A four-bounce monochromator consisting of two channel-cut Si(111) crystals placed between the secondary source and KB-mirrors allows for easy changes between white-beam and monochromatic experiments while maintaining a fixed beam position. High resolution stage scans are performed while recording a fluorescence emission signal or an x-ray diffraction signal coming from either a monochromatic or a white focused beam. The former allows for elemental mapping, whereas the latter is used to produce two-dimensional maps of crystal-phases, -orientation, -texture, and -strain/stress. Typically achieved strain resolution is in the order of 5x10(-5) strain units. Accurate sample positioning in the x-ray focus spot is achieved with a commercial laser-triangulation unit. A Si-drift detector serves as a high-energy-resolution (approximately 150 eV full width at half maximum) fluorescence detector. Fluorescence scans can be collected in continuous scan mode with up to 300 pixels/s scan speed. A charge coupled device area detector is utilized as diffraction detector. Diffraction can be performed in reflecting or transmitting geometry. Diffraction data are processed using XMAS, an in-house written software package for Laue and monochromatic microdiffraction analysis.

Predicting the stability of endangered stonecats in the LaPlatte River, Vermont

USGS Publications Warehouse

Puchala, Elizabeth A.; Parrish, Donna; Donovan, Therese M.

2016-01-01

Stonecats Noturus flavus in Vermont conform to a rare distribution pattern (as designated by Rabinowitz 1981) because their known distribution within the state is limited to the LaPlatte and Missisquoi rivers. We focused on Stonecats in the LaPlatte River to predict the stability of the population. During 2012–2014, we captured Stonecats via backpack electrofishing; fish were PIT-tagged (>90 mm TL) and marked with visible implant elastomer. Among the 1,671 Stonecats that were captured, 1,252 were PIT-tagged. Only 156 (12%) of the PIT-tagged fish were recaptured, and only 22 of those individuals were recaptured more than once. The Pradel model in Program MARK was used to estimate apparent survival (Φ) and seniority, which were used to derive the rate of population change (λ) for the Stonecat encounter histories we studied. We examined a total of 64 models in our candidate set, with the following covariates: TL at first capture, maximum temperature, season, maximum discharge, and area sampled. Survival estimates were highest in the spring (range of daily Φ = 0.9993–0.9995) and increased with greater TL at first capture. We also estimated increases in capture probability with increasing area sampled. We derived an annual λ of 0.9794, which indicates a slightly decreasing population. However, our λ estimate contained uncertainty that was likely increased due to the low recapture rates. Additional years of data could increase the accuracy of the λ estimate. In the meantime, we have provided insight into Stonecat population parameters that were otherwise unknown.

Airborne Precision Spacing: A Trajectory-based Approach to Improve Terminal Area Operations

NASA Technical Reports Server (NTRS)

Barmore, Bryan

2006-01-01

Airborne Precision Spacing has been developed by the National Aeronautics and Space Administration (NASA) over the past seven years as an attempt to benefit from the capabilities of the flight deck to precisely space their aircraft relative to another aircraft. This development has leveraged decades of work on improving terminal area operations, especially the arrival phase. With APS operations, the air traffic controller instructs the participating aircraft to achieve an assigned inter-arrival spacing interval at the runway threshold, relative to another aircraft. The flight crew then uses airborne automation to manage the aircraft s speed to achieve the goal. The spacing tool is designed to keep the speed within acceptable operational limits, promote system-wide stability, and meet the assigned goal. This reallocation of tasks with the controller issuing strategic goals and the flight crew managing the tactical achievement of those goals has been shown to be feasible through simulation and flight test. A precision of plus or minus 2-3 seconds is generally achievable. Simulations of long strings of arriving traffic show no signs of instabilities or compression waves. Subject pilots have rated the workload to be similar to current-day operations and eye-tracking data substantiate this result. This paper will present a high-level review of research results over the past seven years from a variety of tests and experiments. The results will focus on the precision and accuracy achievable, flow stability and some major sources of uncertainty. The paper also includes a summary of the flight crew s procedures and interface and a brief concept overview.

Advances in neglected tropical disease vaccines: Developing relative potency and functional assays for the Na-GST-1/Alhydrogel hookworm vaccine.

PubMed

Brelsford, Jill B; Plieskatt, Jordan L; Yakovleva, Anna; Jariwala, Amar; Keegan, Brian P; Peng, Jin; Xia, Pengjun; Li, Guangzhao; Campbell, Doreen; Periago, Maria Victoria; Correa-Oliveira, Rodrigo; Bottazzi, Maria Elena; Hotez, Peter J; Diemert, David; Bethony, Jeffrey M

2017-02-01

A new generation of vaccines for the neglected tropical diseases (NTDs) have now advanced into clinical development, with the Na-GST-1/Alhydrogel Hookworm Vaccine already being tested in Phase 1 studies in healthy adults. The current manuscript focuses on the often overlooked critical aspects of NTD vaccine product development, more specifically, vaccine stability testing programs. A key measure of vaccine stability testing is "relative potency" or the immunogenicity of the vaccine during storage. As with most NTD vaccines, the Na-GST-1/Alhydrogel Hookworm Vaccine was not developed by attenuation or inactivation of the pathogen (Necator americanus), so conventional methods for measuring relative potency are not relevant for this investigational product. Herein, we describe a novel relative potency testing program and report for the first time on the clinical lot of this NTD vaccine during its first 60 months of storage at 2-8°C. We also describe the development of a complementary functional assay that measures the ability of IgG from animals or humans immunized with Na-GST-1/Alhydrogel to neutralize this important hookworm enzyme. While 90% inhibition of the catalytic activity of Na-GST-1 was achieved in animals immunized with Na-GST-1/Alhydrogel, lower levels of inhibition were observed in immunized humans. Moreover, anti-Na-GST-1 antibodies from volunteers in non-hookworm endemic areas were better able to inhibit catalytic activity than anti-Na-GST-1 antibodies from volunteers resident in hookworm endemic areas. The results described herein provide the critical tools for the product development of NTD vaccines.

Recent progress in stabilizing hybrid perovskites for solar cell applications

NASA Astrophysics Data System (ADS)

Chen, Jianqing; Cai, Xin; Yang, Donghui; Song, Dan; Wang, Jiajia; Jiang, Jinghua; Ma, Aibin; Lv, Shiquan; Hu, Michael Z.; Ni, Chaoying

2017-07-01

Hybrid inorganic-organic perovskites have quickly evolved as a promising group of materials for solar cells and optoelectronic applications mainly owing to the inexpensive materials, relatively simple and versatile fabrication and high power conversion efficiency (PCE). The certified energy conversion efficiency for perovskite solar cell (PSC) has reached above 20%, which is compatible to the current best for commercial applications. However, long-term stabilities of the materials and devices remain to be the biggest challenging issue for realistic implementation of the PSCs. This article discusses the key issues related to the stability of perovskite absorbing layer including crystal structural stability, chemical stability under moisture, oxygen, illumination and interface reaction, effects of electron-transporting materials (ETM), hole-transporting materials (HTM), contact electrodes, ion migration and preparation conditions. Towards the end, prospective strategies for improving the stability of PSCs are also briefly discussed and summarized. We focus on recent understanding of the stability of materials and devices and our perspectives about the strategies for the stability improvement.

Isoperimetric surfaces and area-angular momentum inequality in a rotating black hole in new massive gravity

NASA Astrophysics Data System (ADS)

Aceña, Andrés; López, Ericson; Llerena, Mario

2018-03-01

We study the existence and stability of isoperimetric surfaces in a family of rotating black holes in new massive gravity. We show that the stability of such surfaces is determined by the sign of the hair parameter. We use the isoperimetric surfaces to find a geometric inequality between the area and the angular momentum of the black hole, conjecturing geometric inequalities for more general black holes.

University role in astronaut life support systems: Extravehicular guidance and stabilization in space

NASA Technical Reports Server (NTRS)

Vonrenner, L. C.

1972-01-01

Two problem areas are reviewed: (1) the nature of and approach to the EVA mission and (2) the guidance and stabilization required of such a mission. The report indicates several broad areas in which additional research is needed to provide an advance to the state-of-the-art. Moreover, the research problems cited were chosen from among many as those most amenable to research and study in the university environment.

Enhanced mechanical, thermal, and electric properties of graphene aerogels via supercritical ethanol drying and high-temperature thermal reduction.

PubMed

Cheng, Yehong; Zhou, Shanbao; Hu, Ping; Zhao, Guangdong; Li, Yongxia; Zhang, Xinghong; Han, Wenbo

2017-05-03

Graphene aerogels with high surface areas, ultra-low densities and thermal conductivities have been prepared to exploit their wide applications from pollution adsorption to energy storage, supercapacitor, and thermal insulation. However, the low mechanical properties, poor thermal stability and electric conductivity restrict these aerogels' applications. In this paper, we prepared mechanically strong graphene aerogels with large BET surface areas, low thermal conductivities, high thermal stability and electric conductivities via hydrothermal reduction and supercritical ethanol drying. Annealing at 1500 °C resulted in slightly increased thermal conductivity and further improvement in mechanical properties, oxidation temperature and electric conductivity of the graphene aerogel. The large BET surface areas, together with strong mechanical properties, low thermal conductivities, high thermal stability and electrical conductivities made these graphene aerogels feasible candidates for use in a number of fields covering from batteries to sensors, electrodes, lightweight conductor and insulation materials.

Thermal stability of charged rotating quantum black holes

NASA Astrophysics Data System (ADS)

Sinha, Aloke Kumar; Majumdar, Parthasarathi

2017-12-01

Criteria for thermal stability of charged rotating black holes of any dimension are derived for horizon areas that are large relative to the Planck area (in these dimensions). The derivation is based on generic assumptions of quantum geometry, supported by some results of loop quantum gravity, and equilibrium statistical mechanics of the Grand Canonical ensemble. There is no explicit use of classical spacetime geometry in this analysis. The only assumption is that the mass of the black hole is a function of its horizon area, charge and angular momentum. Our stability criteria are then tested in detail against specific classical black holes in spacetime dimensions 4 and 5, whose metrics provide us with explicit relations for the dependence of the mass on the charge and angular momentum of the black holes. This enables us to predict which of these black holes are expected to be thermally unstable under Hawking radiation.

Reactive composite compositions and mat barriers

DOEpatents

Langton, Christine A.; Narasimhan, Rajendran; Karraker, David G.

2001-01-01

A hazardous material storage area has a reactive multi-layer composite mat which lines an opening into which a reactive backfill and hazardous material are placed. A water-inhibiting cap may cover the hazardous material storage area. The reactive multi-layer composite mat has a backing onto which is placed an active layer which will neutralize or stabilize hazardous waste and a fronting layer so that the active layer is between the fronting and backing layers. The reactive backfill has a reactive agent which can stabilize or neutralize hazardous material and inhibit the movement of the hazardous material through the hazardous material storage area.

Tanks Focus Area annual report FY2000

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2000-12-01

The U.S. Department of Energy (DOE) continues to face a major radioactive waste tank remediation effort with tanks containing hazardous and radioactive waste resulting from the production of nuclear materials. With some 90 million gallons of waste in the form of solid, sludge, liquid, and gas stored in 287 tanks across the DOE complex, containing approximately 650 million curies, radioactive waste storage tank remediation is the nation's highest cleanup priority. Differing waste types and unique technical issues require specialized science and technology to achieve tank cleanup in an environmentally acceptable manner. Some of the waste has been stored for overmore » 50 years in tanks that have exceeded their design lives. The challenge is to characterize and maintain these contents in a safe condition and continue to remediate and close each tank to minimize the risks of waste migration and exposure to workers, the public, and the environment. In 1994, the DOE's Office of Environmental Management (EM) created a group of integrated, multiorganizational teams focusing on specific areas of the EM cleanup mission. These teams have evolved into five focus areas managed within EM's Office of Science and Technology (OST): Tanks Focus Area (TFA); Deactivation and Decommissioning Focus Area; Nuclear Materials Focus Area; Subsurface Contaminants Focus Area; and Transuranic and Mixed Waste Focus Area.« less

Integrating the effects of forest cover on slope stability in a deterministic landslide susceptibility model (TRIGRS 2.0)

NASA Astrophysics Data System (ADS)

Zieher, T.; Rutzinger, M.; Bremer, M.; Meissl, G.; Geitner, C.

2014-12-01

The potentially stabilizing effects of forest cover in respect of slope stability have been the subject of many studies in the recent past. Hence, the effects of trees are also considered in many deterministic landslide susceptibility models. TRIGRS 2.0 (Transient Rainfall Infiltration and Grid-Based Regional Slope-Stability; USGS) is a dynamic, physically-based model designed to estimate shallow landslide susceptibility in space and time. In the original version the effects of forest cover are not considered. As for further studies in Vorarlberg (Austria) TRIGRS 2.0 is intended to be applied in selected catchments that are densely forested, the effects of trees on slope stability were implemented in the model. Besides hydrological impacts such as interception or transpiration by tree canopies and stems, root cohesion directly influences the stability of slopes especially in case of shallow landslides while the additional weight superimposed by trees is of minor relevance. Detailed data on tree positions and further attributes such as tree height and diameter at breast height were derived throughout the study area (52 km²) from high-resolution airborne laser scanning data. Different scenarios were computed for spruce (Picea abies) in the study area. Root cohesion was estimated area-wide based on published correlations between root reinforcement and distance to tree stems depending on the stem diameter at breast height. In order to account for decreasing root cohesion with depth an exponential distribution was assumed and implemented in the model. Preliminary modelling results show that forest cover can have positive effects on slope stability yet strongly depending on tree age and stand structure. This work has been conducted within C3S-ISLS, which is funded by the Austrian Climate and Energy Fund, 5th ACRP Program.

Role of an anatomically contoured plate and metal block for balanced stability between the implant and lateral hinge in open-wedge high-tibial osteotomy.

PubMed

Jang, Young Woong; Lim, DoHyung; Seo, Hansol; Lee, Myung Chul; Lee, O-Sung; Lee, Yong Seuk

2018-07-01

Open-wedge high tibial osteotomy (OWHTO) is a well-established surgical option for medial compartment osteoarthritis of the varus knee. The initial strength of the fixation plate is critical for successful correction maintenance and healing of the osteotomy site. This study was conducted to verify if a newly designed anatomical plate (LCfit) improves the stability of both the medial implant and lateral hinge area, as well as to evaluate how the metal block contributes to both medial and lateral stability. A finite element (FE) tibial model was combined with TomoFix plate, a LCfit plate with and without a metal block. Data analysis was conducted to evaluate the balanced stability, which refers to the enforced lateral stability resulting from redistribution of overall stress. We assessed the balanced stability of the medial implant and lateral hinge area in three cases using the same Sawbones and loads using the tibia FE model. The LCfit plate reduced stress by 23.1% at the lateral hinge compared to the TomoFix plate (TomoFix vs. LCfit: 34.2 ± 23.3 MPa vs. 26.3 ± 17.5 MPa). The LCfit plate with a metal block reduced stress by 40.1% at the medial plate (210.1 ± 64.2 MPa vs. 125.8 ± 65.7 MPa) and by 31.2% (26.3 ± 17.5 MPa vs. 18.1 ± 12.1 MPa) at the lateral hinge area compared to the reduction using the LCfit plate without a metal block. The newly designed fixation system for OWHTO balanced the overall stress distribution and reduced stress at the lateral hinge area compared to that using a conventional fixation system. The addition of the metal block showed additional benefits for balanced stability between the medial implant and lateral hinge area. However, this conclusion could only be drawn using the FE model in this study. Therefore, further clinical studies are necessary to reveal the clinical effect of reduced lateral stress on the occurrence of the lateral hinge fracture and the biologic effect of the metal block on the healing of the medial cortex.

Motion compensation using a suctioning stabilizer for intravital microscopy

PubMed Central

Vinegoni, Claudio; Lee, Sungon; Gorbatov, Rostic; Weissleder, Ralph

2013-01-01

Motion artifacts continue to present a major challenge to single cell imaging in cardiothoracic organs such as the beating heart, blood vessels, or lung. In this study, we present a new water-immersion suctioning stabilizer that enables minimally invasive intravital fluorescence microscopy using water-based stick objectives. The stabilizer works by reducing major motion excursions and can be used in conjunction with both prospective or retrospective gating approaches. We show that the new approach offers cellular resolution in the beating murine heart without perturbing normal physiology. In addition, because this technique allows multiple areas to be easily probed, it offers the opportunity for wide area coverage at high resolution. PMID:24086796

Evolutionary consequences of climate-induced range shifts in insects.

PubMed

Sánchez-Guillén, Rosa A; Córdoba-Aguilar, Alex; Hansson, Bengt; Ott, Jürgen; Wellenreuther, Maren

2016-11-01

Range shifts can rapidly create new areas of geographic overlap between formerly allopatric taxa and evidence is accumulating that this can affect species persistence. We review the emerging literature on the short- and long-term consequences of these geographic range shifts. Specifically, we focus on the evolutionary consequences of novel species interactions in newly created sympatric areas by describing the potential (i) short-term processes acting on reproductive barriers between species and (ii) long-term consequences of range shifts on the stability of hybrid zones, introgression and ultimately speciation and extinction rates. Subsequently, we (iii) review the empirical literature on insects to evaluate which processes have been studied, and (iv) outline some areas that deserve increased attention in the future, namely the genomics of hybridisation and introgression, our ability to forecast range shifts and the impending threat from insect vectors and pests on biodiversity, human health and crop production. Our review shows that species interactions in de novo sympatric areas can be manifold, sometimes increasing and sometimes decreasing species diversity. A key issue that emerges is that climate-induced hybridisations in insects are much more widespread than anticipated and that rising temperatures and increased anthropogenic disturbances are accelerating the process of species mixing. The existing evidence only shows the tip of the iceberg and we are likely to see many more cases of species mixing following range shifts in the near future. © 2015 Cambridge Philosophical Society.

A framework for activity detection in wide-area motion imagery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Porter, Reid B; Ruggiero, Christy E; Morrison, Jack D

2009-01-01

Wide-area persistent imaging systems are becoming increasingly cost effective and now large areas of the earth can be imaged at relatively high frame rates (1-2 fps). The efficient exploitation of the large geo-spatial-temporal datasets produced by these systems poses significant technical challenges for image and video analysis and data mining. In recent years there has been significant progress made on stabilization, moving object detection and tracking and automated systems now generate hundreds to thousands of vehicle tracks from raw data, with little human intervention. However, the tracking performance at this scale, is unreliable and average track length is much smallermore » than the average vehicle route. This is a limiting factor for applications which depend heavily on track identity, i.e. tracking vehicles from their points of origin to their final destination. In this paper we propose and investigate a framework for wide-area motion imagery (W AMI) exploitation that minimizes the dependence on track identity. In its current form this framework takes noisy, incomplete moving object detection tracks as input, and produces a small set of activities (e.g. multi-vehicle meetings) as output. The framework can be used to focus and direct human users and additional computation, and suggests a path towards high-level content extraction by learning from the human-in-the-loop.« less

Medical applications of nanotechnology.

PubMed

Zdrojewicz, Zygmunt; Waracki, Mateusz; Bugaj, Bartosz; Pypno, Damian; Cabała, Krzysztof

2015-10-29

Nanotechnologies are new areas of research focusing on affecting matter at the atomic and molecular levels. It is beyond doubt that modern medicine can benefit greatly from it; thus nanomedicine has become one of the main branches of nanotechnological research. Currently it focuses on developing new methods of preventing, diagnosing and treating various diseases. Nanomaterials show very high efficiency in destroying cancer cells and are already undergoing clinical trials. The results are so promising that nanomaterials might become an alternative to traditional cancer therapy, mostly due to the fact that they allow cancer cells to be targeted specifically and enable detailed imaging of tissues, making planning further therapy much easier. Nanoscience might also be a source of the needed breakthrough in the fight against atherosclerosis, since nanostructures may be used in both preventing and increasing the stability of atherosclerotic lesions. One area of interest is creating nanomaterials that are not only efficient, but also well tolerated by the human body. Other potential applications of nanotechnology in medicine include: nanoadjuvants with immunomodulatory properties used to deliver vaccine antigens; the nano-knife, an almost non-invasive method of destroying cancer cells with high voltage electricity; and carbon nanotubes, which are already a popular way of repairing damaged tissues and might be used to regenerate nerves in the future. The aim of this article is to outline the potential uses of nanotechnology in medicine. Original articles and reviews have been used to present the new developments and directions of studies.

Propulsion Research at the Propulsion Research Center of the NASA Marshall Space Flight Center

NASA Technical Reports Server (NTRS)

Blevins, John; Rodgers, Stephen

2003-01-01

The Propulsion Research Center of the NASA Marshall Space Flight Center is engaged in research activities aimed at providing the bases for fundamental advancement of a range of space propulsion technologies. There are four broad research themes. Advanced chemical propulsion studies focus on the detailed chemistry and transport processes for high-pressure combustion, and on the understanding and control of combustion stability. New high-energy propellant research ranges from theoretical prediction of new propellant properties through experimental characterization propellant performance, material interactions, aging properties, and ignition behavior. Another research area involves advanced nuclear electric propulsion with new robust and lightweight materials and with designs for advanced fuels. Nuclear electric propulsion systems are characterized using simulated nuclear systems, where the non-nuclear power source has the form and power input of a nuclear reactor. This permits detailed testing of nuclear propulsion systems in a non-nuclear environment. In-space propulsion research is focused primarily on high power plasma thruster work. New methods for achieving higher thrust in these devices are being studied theoretically and experimentally. Solar thermal propulsion research is also underway for in-space applications. The fourth of these research areas is advanced energetics. Specific research here includes the containment of ion clouds for extended periods. This is aimed at proving the concept of antimatter trapping and storage for use ultimately in propulsion applications. Another activity in this involves research into lightweight magnetic technology for space propulsion applications.

Hormone purification by isoelectric focusing in space

NASA Technical Reports Server (NTRS)

Bier, M.

1988-01-01

The objective of the program was the definition and development of optimal methods for electrophoretic separations in microgravity. The approach is based on a triad consisting of ground based experiments, mathematical modeling and experiments in microgravity. Zone electrophoresis is a rate process, where separation is achieved in uniform buffers on the basis of differences in electrophoretic mobilities. Optimization and modeling of continuous flow electrophoresis mainly concern the hydrodynamics of the flow process, including gravity dependent fluid convection due to density gradients and gravity independent electroosmosis. Optimization of focusing requires a more complex model describing the molecular transport processes involved in electrophoresis of interacting systems. Three different focusing instruments were designed, embodying novel principles of fluid stabilization. Fluid stability was achieved by: (1) flow streamlining by means of membrane elements in combination with rapid fluid recycling; (2) apparatus rotation in combination with said membrane elements; and (3) shear stress induced by rapid recycling through a narrow gap channel.

Mechanical design of multiple zone plates precision alignment apparatus for hard X-ray focusing in twenty-nanometer scale

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shu, Deming; Liu, Jie; Gleber, Sophie C.

An enhanced mechanical design of multiple zone plates precision alignment apparatus for hard x-ray focusing in a twenty-nanometer scale is provided. The precision alignment apparatus includes a zone plate alignment base frame; a plurality of zone plates; and a plurality of zone plate holders, each said zone plate holder for mounting and aligning a respective zone plate for hard x-ray focusing. At least one respective positioning stage drives and positions each respective zone plate holder. Each respective positioning stage is mounted on the zone plate alignment base frame. A respective linkage component connects each respective positioning stage and the respectivemore » zone plate holder. The zone plate alignment base frame, each zone plate holder and each linkage component is formed of a selected material for providing thermal expansion stability and positioning stability for the precision alignment apparatus.« less

Dense plasma focus production in a hypocycloidal pinch

NASA Technical Reports Server (NTRS)

Lee, J. H.; Mcfarland, D. R.; Hohl, F.

1975-01-01

A type of high-power pinch apparatus consisting of disk electrodes was developed, and diagnostic measurements to study its mechanism of dense plasma production were made. The collapse fronts of the current sheets are well organized, and dense plasma focuses are produced on the axis with radial stability in excess of 5 microns. A plasma density greater than 10 to the 18th power/cubic cm was determined with Stark broadening and CO2 laser absorption. A plasma temperature of approximately 1 keV was measured with differential transmission of soft X-rays through thin foils. Essentially complete absorption of a high-energy CO2 laser beam was observed. The advantages of this apparatus over the coaxial plasma focus are in (1) the plasma volume, (2) the stability, (3) the containment time, (4) the easy access to additional heating by laser or electron beams, and (5) the possibility of scaling up to a multiple array for high-power operation.

An Ecohydrological Approach to the Resiliency and Stability of Ecosystems

NASA Astrophysics Data System (ADS)

Peña Alzate, S.; Canon Barriga, J. E.

2013-12-01

We introduce a simplified ecohydrological model to quantitatively assess the resiliency and stability of ecosystems. The proposed model couples a hydrological soil moisture balance with a set of spatiotemporal dynamics of systems and agent-based algorithms to represent the interactions among several plant populations in a gridded area under different water, soil and temperature constraints. The model also allows disturbances, representing mostly the effects of deforestation practices. The simulated ecosystem, composed by a set of plant populations, includes allometric rules (i.e., power laws for generational and reproductive times, linear approximations for water and temperature gains, losses and optimal values and a set of intra and interspecific interaction rules based on high, optimal and low competition responses among the populations). Disturbances are determined by a clearance of populations in a defined area within the model's domain. The effects of climate variability can be also incorporated through precipitation and temperature time series that exhibit trends and heteroskedasticity. Resiliency and stability are calculated with modified indices that are used in hydrology, in this case to determine the ability of the ecosystem to recover from a disturbance. The model represents different types of plant phenotypes showing exponential growth in the first steps of the simulations. The indices, evaluated on each population and over the structure of the entire ecosystem, show how different populations respond differently to disturbances, following behaviors similar to those expected in nature, like high reproduction rates on gregarious plants with short generation times, and low densities in plants with high generations times. The selection of plant populations was mainly focused on the concept of biodiversity with emphasis on tropical regions. The model can represent the spatial and temporal succession of the ecosystem after being disturbed. The model also shows the differences between a disturbed and undisturbed ecosystem in a temporal scale, and how the differences in the phenotypical characteristics of plant populations can be advantageous or disadvantageous when they are disturbed. This ecohydrological model is intended to be used as an aid for making decisions about restoration and conservation practices, and also to help understanding resilience and stability of ecosystems, especially in tropical forests under climate change scenarios. Acknowledgements: authors thank the financial support of COLCIENCIAS (program Jovenes Investigadores e innovadores 2012), GAIA group and Universidad de Antioquia through its Sustainability Program 2011-2012.

Fuzzy wavelet plus a quantum neural network as a design base for power system stability enhancement.

PubMed

Ganjefar, Soheil; Tofighi, Morteza; Karami, Hamidreza

2015-11-01

In this study, we introduce an indirect adaptive fuzzy wavelet neural controller (IAFWNC) as a power system stabilizer to damp inter-area modes of oscillations in a multi-machine power system. Quantum computing is an efficient method for improving the computational efficiency of neural networks, so we developed an identifier based on a quantum neural network (QNN) to train the IAFWNC in the proposed scheme. All of the controller parameters are tuned online based on the Lyapunov stability theory to guarantee the closed-loop stability. A two-machine, two-area power system equipped with a static synchronous series compensator as a series flexible ac transmission system was used to demonstrate the effectiveness of the proposed controller. The simulation and experimental results demonstrated that the proposed IAFWNC scheme can achieve favorable control performance. Copyright © 2015 Elsevier Ltd. All rights reserved.

Army Civil Affairs Functional Specialists: On the Verge of Extinction

DTIC Science & Technology

2012-03-22

the following six areas: rule of law, economic stability , infrastructure, governance, public health and welfare, and public education and information...as defined in table 1. Rule of Law Economic Stability Infrastructure Rule of law pertains to the fair, competent, and efficient application and... Economic stability pertains to the efficient management (for example, production, distribution, trade, and consumption) of resources, goods

Passive and Active Contributions to Glenohumeral Stability

DTIC Science & Technology

2001-10-25

physiological muscle contraction during free arm suspension and proportional to muscle physiological cross- sectional area [15] (Phys Load); ditto...of muscle contraction around GH-joint. Stiffness of the GH capsuloligamentous structure, which is the ratio of the force required to stretch the...important active stabilizer in inferior stability. Our results also suggested that low-level muscle activity (2% of maximum muscle contraction ), representing

Work-Family Boundary Strategies: Stability and Alignment between Preferred and Enacted Boundaries

ERIC Educational Resources Information Center

Ammons, Samantha K.

2013-01-01

Are individuals bounding work and family the way they would like? Much of the work-family boundary literature focuses on whether employees are segmenting or integrating work with family, but does not explore the boundaries workers would like to have, nor does it examine the fit between desired and enacted boundaries, or assess boundary stability.…

Grade Assignments and the Teacher Pipeline: A Low-Cost Lever to Improve Student Achievement?

ERIC Educational Resources Information Center

Blazar, David

2015-01-01

Research on teacher stability typically focuses on the extent to which teachers remain in the same school, district, or the teaching profession from one year to the next. I investigate another facet of stability--whether teachers remain in the grade they teach. Drawing on administrative data from a large district in California, I find that high…

Planning for Action: Campaign Concepts and Tools

DTIC Science & Technology

2012-08-01

142 10-15. Stability Mechanisms – Army .................................... 143 10-16. Stability Mechanisms – Joint...defeat mechanisms, which focus 143 the destructive and coercive capabilities of the force to provide security and public order and safety for...Matthew B. Ridgway. GEN Ridgway successfully led the 82d Airborne Division and XVIII Airborne Corps in the ETO during World War II and Eighth (US

Stability of College Students' Fit with Their Academic Major and the Relationship between Academic Fit and Occupational Fit

ERIC Educational Resources Information Center

Ghandour, Louma

2013-01-01

This study examines the fit between students' interests and their academic choices at different stages of their college careers. Using image theory (Beach, 1990) as an integrated theory of person-vocation fit, this investigation focuses on the stability of academic fit during college and the relationship between fit with academic choice and fit…

The Triton: Design concepts and methods

NASA Technical Reports Server (NTRS)

Meholic, Greg; Singer, Michael; Vanryn, Percy; Brown, Rhonda; Tella, Gustavo; Harvey, Bob

1992-01-01

During the design of the C & P Aerospace Triton, a few problems were encountered that necessitated changes in the configuration. After the initial concept phase, the aspect ratio was increased from 7 to 7.6 to produce a greater lift to drag ratio (L/D = 13) which satisfied the horsepower requirements (118 hp using the Lycoming O-235 engine). The initial concept had a wing planform area of 134 sq. ft. Detailed wing sizing analysis enlarged the planform area to 150 sq. ft., without changing its layout or location. The most significant changes, however, were made just prior to inboard profile design. The fuselage external diameter was reduced from 54 to 50 inches to reduce drag to meet the desired cruise speed of 120 knots. Also, the nose was extended 6 inches to accommodate landing gear placement. Without the extension, the nosewheel received an unacceptable percentage (25 percent) of the landing weight. The final change in the configuration was made in accordance with the stability and control analysis. In order to reduce the static margin from 20 to 13 percent, the horizontal tail area was reduced from 32.02 to 25.0 sq. ft. The Triton meets all the specifications set forth in the design criteria. If time permitted another iteration of the calculations, two significant changes would be made. The vertical stabilizer area would be reduced to decrease the aircraft lateral stability slope since the current value was too high in relation to the directional stability slope. Also, the aileron size would be decreased to reduce the roll rate below the current 106 deg/second. Doing so would allow greater flap area (increasing CL(sub max)) and thus reduce the overall wing area. C & P would also recalculate the horsepower and drag values to further validate the 120 knot cruising speed.

Hybrid rocket engine, theoretical model and experiment

NASA Astrophysics Data System (ADS)

Chelaru, Teodor-Viorel; Mingireanu, Florin

2011-06-01

The purpose of this paper is to build a theoretical model for the hybrid rocket engine/motor and to validate it using experimental results. The work approaches the main problems of the hybrid motor: the scalability, the stability/controllability of the operating parameters and the increasing of the solid fuel regression rate. At first, we focus on theoretical models for hybrid rocket motor and compare the results with already available experimental data from various research groups. A primary computation model is presented together with results from a numerical algorithm based on a computational model. We present theoretical predictions for several commercial hybrid rocket motors, having different scales and compare them with experimental measurements of those hybrid rocket motors. Next the paper focuses on tribrid rocket motor concept, which by supplementary liquid fuel injection can improve the thrust controllability. A complementary computation model is also presented to estimate regression rate increase of solid fuel doped with oxidizer. Finally, the stability of the hybrid rocket motor is investigated using Liapunov theory. Stability coefficients obtained are dependent on burning parameters while the stability and command matrixes are identified. The paper presents thoroughly the input data of the model, which ensures the reproducibility of the numerical results by independent researchers.

Note: Large active area solid state photon counter with 20 ps timing resolution and 60 fs detection delay stability

NASA Astrophysics Data System (ADS)

Prochazka, Ivan; Kodet, Jan; Eckl, Johann; Blazej, Josef

2017-10-01

We are reporting on the design, construction, and performance of a photon counting detector system, which is based on single photon avalanche diode detector technology. This photon counting device has been optimized for very high timing resolution and stability of its detection delay. The foreseen application of this detector is laser ranging of space objects, laser time transfer ground to space and fundamental metrology. The single photon avalanche diode structure, manufactured on silicon using K14 technology, is used as a sensor. The active area of the sensor is circular with 200 μm diameter. Its photon detection probability exceeds 40% in the wavelength range spanning from 500 to 800 nm. The sensor is operated in active quenching and gating mode. A new control circuit was optimized to maintain high timing resolution and detection delay stability. In connection to this circuit, timing resolution of the detector is reaching 20 ps FWHM. In addition, the temperature change of the detection delay is as low as 70 fs/K. As a result, the detection delay stability of the device is exceptional: expressed in the form of time deviation, detection delay stability of better than 60 fs has been achieved. Considering the large active area aperture of the detector, this is, to our knowledge, the best timing performance reported for a solid state photon counting detector so far.

Structure and Mechanical Properties of Al-Cu-Fe-X Alloys with Excellent Thermal Stability.

PubMed

Školáková, Andrea; Novák, Pavel; Mejzlíková, Lucie; Průša, Filip; Salvetr, Pavel; Vojtěch, Dalibor

2017-11-05

In this work, the structure and mechanical properties of innovative Al-Cu-Fe based alloys were studied. We focused on preparation and characterization of rapidly solidified and hot extruded Al-Cu-Fe, Al-Cu-Fe-Ni and Al-Cu-Fe-Cr alloys. The content of transition metals affects mechanical properties and structure. For this reason, microstructure, phase composition, hardness and thermal stability have been investigated in this study. The results showed exceptional thermal stability of these alloys and very good values of mechanical properties. Alloying by chromium ensured the highest thermal stability, while nickel addition refined the structure of the consolidated alloy. High thermal stability of all tested alloys was described in context with the transformation of the quasicrystalline phases to other types of intermetallics.

Structure and Mechanical Properties of Al-Cu-Fe-X Alloys with Excellent Thermal Stability

PubMed Central

Školáková, Andrea; Novák, Pavel; Mejzlíková, Lucie; Průša, Filip; Salvetr, Pavel; Vojtěch, Dalibor

2017-01-01

In this work, the structure and mechanical properties of innovative Al-Cu-Fe based alloys were studied. We focused on preparation and characterization of rapidly solidified and hot extruded Al-Cu-Fe, Al-Cu-Fe-Ni and Al-Cu-Fe-Cr alloys. The content of transition metals affects mechanical properties and structure. For this reason, microstructure, phase composition, hardness and thermal stability have been investigated in this study. The results showed exceptional thermal stability of these alloys and very good values of mechanical properties. Alloying by chromium ensured the highest thermal stability, while nickel addition refined the structure of the consolidated alloy. High thermal stability of all tested alloys was described in context with the transformation of the quasicrystalline phases to other types of intermetallics. PMID:29113096

Measuring self-esteem in context: the importance of stability of self-esteem in psychological functioning.

PubMed

Kernis, Michael H

2005-12-01

In this article, I report on a research program that has focused on the joint roles of stability and level of self-esteem in various aspects of psychological functioning. Stability of self-esteem refers to the magnitude of short-term fluctuations that people experience in their current, contextually based feelings of self-worth. In contrast, level of self-esteem refers to representations of people's general, or typical, feelings of self-worth. A considerable amount of research reveals that self-esteem stability has predictive value beyond the predictive value of self-esteem level. Moreover, considering self-esteem stability provides one way to distinguish fragile from secure forms of high self-esteem. Results from a number of studies are presented and theoretical implications are discussed.

Confronting stillbirths and newborn deaths in areas of conflict and political instability: a neglected global imperative.

PubMed

Wise, Paul H; Darmstadt, Gary L

2015-08-01

Despite considerable improvements in reproductive and newborn health throughout the world, relatively poor outcomes persist in areas plagued by conflict or political instability. To assess the contribution of areas of conflict and instability to global patterns of stillbirths and newborn deaths and to identify opportunities for effective intervention in these areas. Analysis of the available data on stillbirths and neonatal mortality in association with conflict and governance indicators, and review of epidemiological and political literature pertaining to the provision of health and public services in areas of conflict and instability. Of the 15 countries with the highest neonatal mortality rates in the world, 14 are characterized by chronic conflict or political instability. If India and China are excluded, countries experiencing chronic conflict or political instability account for approximately 42% of all neonatal deaths worldwide. Efforts to address adverse reproductive and newborn outcomes in these areas must adapt recommended intervention protocols to the special security and governance conditions associated with unstable political environment. Despite troubling relative and absolute indicators, the special requirements of improving reproductive and neonatal outcomes in areas affected by conflict and political instability have not received adequate attention. New integrated political and technical strategies will be required. This should include moving beyond traditional approaches concerned with complex humanitarian emergencies. Rather, global efforts must be based on a deeper understanding of the specific governance requirements associated with protracted and widespread health requirements. A focus on women's roles, regional strategies which take advantage of relative stability and governance capacity in neighbouring states, virtual infrastructure, and assistance regimens directed specifically to unstable areas may prove useful.

Recycling isoelectric focusing with computer controlled data acquisition system. [for high resolution electrophoretic separation and purification of biomolecules

NASA Technical Reports Server (NTRS)

Egen, N. B.; Twitty, G. E.; Bier, M.

1979-01-01

Isoelectric focusing is a high-resolution technique for separating and purifying large peptides, proteins, and other biomolecules. The apparatus described in the present paper constitutes a new approach to fluid stabilization and increased throughput. Stabilization is achieved by flowing the process fluid uniformly through an array of closely spaced filter elements oriented parallel both to the electrodes and the direction of the flow. This seems to overcome the major difficulties of parabolic flow and electroosmosis at the walls, while limiting the convection to chamber compartments defined by adjacent spacers. Increased throughput is achieved by recirculating the process fluid through external heat exchange reservoirs, where the Joule heat is dissipated.

PrimeSupplier Cross-Program Impact Analysis and Supplier Stability Indicator Simulation Model

NASA Technical Reports Server (NTRS)

Calluzzi, Michael

2009-01-01

PrimeSupplier, a supplier cross-program and element-impact simulation model, with supplier solvency indicator (SSI), has been developed so that the shuttle program can see early indicators of supplier and product line stability, while identifying the various elements and/or programs that have a particular supplier or product designed into the system. The model calculates two categories of benchmarks to determine the SSI, with one category focusing on agency programmatic data and the other focusing on a supplier's financial liquidity. PrimeSupplier was developed to help NASA smoothly transition design, manufacturing, and repair operations from the Shuttle program to the Constellation program, without disruption in the industrial supply base.

Nanoparticle-Hydrogel: A Hybrid Biomaterial System for Localized Drug Delivery

PubMed Central

Gao, Weiwei; Zhang, Yue; Zhang, Qiangzhe; Zhang, Liangfang

2016-01-01

Nanoparticles have offered a unique set of properties for drug delivery including high drug loading capacity, combinatorial delivery, controlled and sustained drug release, prolonged stability and lifetime, and targeted delivery. To further enhance therapeutic index, especially for localized application, nanoparticles have been increasingly combined with hydrogels to form a hybrid biomaterial system for controlled drug delivery. Herein, we review recent progresses in engineering such nanoparticle-hydrogel hybrid system (namely ‘NP-gel’) with a particular focus on its application for localized drug delivery. Specifically, we highlight four research areas where NP-gel has shown great promises, including (1) passively controlled drug release, (2) stimuli-responsive drug delivery, (3) site-specific drug delivery, and (4) detoxification. Overall, integrating therapeutic nanoparticles with hydrogel technologies creates a unique and robust hybrid biomaterial system that enables effective localized drug delivery. PMID:26951462

Inorganic Nanomaterials as Carriers for Drug Delivery.

PubMed

Chen, Shizhu; Hao, Xiaohong; Liang, Xingjie; Zhang, Qun; Zhang, Cuimiao; Zhou, Guoqiang; Shen, Shigang; Jia, Guang; Zhang, Jinchao

2016-01-01

For safe and effective therapy, drugs must be delivered efficiently and with minimal systemic side effects. Nanostructured drug carriers enable the delivery of small-molecule drugs as well as nucleic acids and proteins. Inorganic nanomaterials are ideal for drug delivery platforms due to their unique physicochemical properties, such as facile preparation, good storage stability and biocompatibility. Many inorganic nanostructure-based drug delivery platforms have been prepared. Although there are still many obstacles to overcome, significant advances have been made in recent years. This review focuses on the status and development of inorganic nanostructures, including silica, quantum dots, gold, carbon-based and magnetic iron oxide-based nanostructures, as carriers for chemical and biological drugs. We specifically highlight the extensive use of these inorganic drug carriers for cancer therapy. Finally, we discuss the most important areas in the field that urgently require further study.

Chemically modified graphene based supercapacitors for flexible and miniature devices

NASA Astrophysics Data System (ADS)

Ghosh, Debasis; Kim, Sang Ouk

2015-09-01

Rapid progress in the portable and flexible electronic devises has stimulated supercapacitor research towards the design and fabrication of high performance flexible devices. Recent research efforts for flexible supercapacitor electrode materials are highly focusing on graphene and chemically modified graphene owing to the unique properties, including large surface area, high electrical and thermal conductivity, excellent mechanical flexibility, and outstanding chemical stability. This invited review article highlights current status of the flexible electrode material research based on chemically modified graphene for supercapacitor application. A variety of electrode architectures prepared from chemically modified graphene are summarized in terms of their structural dimensions. Novel prototypes for the supercapacitor aiming at flexible miniature devices, i.e. microsupercapacitor with high energy and power density are highlighted. Future challenges relevant to graphene-based flexible supercapacitors are also suggested. [Figure not available: see fulltext.

Ionic Liquid-Based Optical and Electrochemical Carbon Dioxide Sensors.

PubMed

Behera, Kamalakanta; Pandey, Shubha; Kadyan, Anu; Pandey, Siddharth

2015-12-04

Due to their unusual physicochemical properties (e.g., high thermal stability, low volatility, high intrinsic conductivity, wide electrochemical windows and good solvating ability), ionic liquids have shown immense application potential in many research areas. Applications of ionic liquid in developing various sensors, especially for the sensing of biomolecules, such as nucleic acids, proteins and enzymes, gas sensing and sensing of various important ions, among other chemosensing platforms, are currently being explored by researchers worldwide. The use of ionic liquids for the detection of carbon dioxide (CO₂) gas is currently a major topic of research due to the associated importance of this gas with daily human life. This review focuses on the application of ionic liquids in optical and electrochemical CO₂ sensors. The design, mechanism, sensitivity and detection limit of each type of sensor are highlighted in this review.

The integrated manual and automatic control of complex flight systems

NASA Technical Reports Server (NTRS)

Schmidt, David K.

1991-01-01

Research dealt with the general area of optimal flight control synthesis for manned flight vehicles. The work was generic; no specific vehicle was the focus of study. However, the class of vehicles generally considered were those for which high authority, multivariable control systems might be considered, for the purpose of stabilization and the achievement of optimal handling characteristics. Within this scope, the topics of study included several optimal control synthesis techniques, control-theoretic modeling of the human operator in flight control tasks, and the development of possible handling qualities metrics and/or measures of merit. Basic contributions were made in all these topics, including human operator (pilot) models for multi-loop tasks, optimal output feedback flight control synthesis techniques; experimental validations of the methods developed, and fundamental modeling studies of the air-to-air tracking and flared landing tasks.

Engineered Graphene Materials: Synthesis and Applications for Polymer Electrolyte Membrane Fuel Cells.

PubMed

He, Daping; Tang, Haolin; Kou, Zongkui; Pan, Mu; Sun, Xueliang; Zhang, Jiujun; Mu, Shichun

2017-05-01

Engineered graphene materials (EGMs) with unique structures and properties have been incorporated into various components of polymer electrolyte membrane fuel cells (PEMFCs) such as electrode, membrane, and bipolar plates to achieve enhanced performances in terms of electrical conductivity, mechanical durability, corrosion resistance, and electrochemical surface area. This research news article provides an overview of the recent development in EGMs and EGM-based PEMFCs with a focus on the effects of EGMs on PEMFC performance when they are incorporated into different components of PEMFCs. The challenges of EGMs for practical PEMFC applications in terms of production scale, stability, conductivity, and coupling capability with other materials are also discussed and the corresponding measures and future research trends to overcome such challenges are proposed. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Environmental Management vitrification activities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krumrine, P.H.

1996-05-01

Both the Mixed Waste and Landfill Stabilization Focus Areas as part of the Office of Technology Development efforts within the Department of Energy`s (DOE) Environmental Management (EM) Division have been developing various vitrification technologies as a treatment approach for the large quantities of transuranic (TRU), TRU mixed and Mixed Low Level Wastes that are stored in either landfills or above ground storage facilities. The technologies being developed include joule heated, plasma torch, plasma arc, induction, microwave, combustion, molten metal, and in situ methods. There are related efforts going into development glass, ceramic, and slag waste form windows of opportunity formore » the diverse quantities of heterogeneous wastes needing treatment. These studies look at both processing parameters, and long term performance parameters as a function of composition to assure that developed technologies have the right chemistry for success.« less

Phospholipid Bilayers: Stability and Encapsulation of Nanoparticles

NASA Astrophysics Data System (ADS)

Alipour, Elnaz; Halverson, Duncan; McWhirter, Samantha; Walker, Gilbert C.

2017-05-01

Nanoparticles are widely studied for their potential medical uses in diagnostics and therapeutics. The interface between a nanoparticle and its target has been a focus of research, both to guide the nanoparticle and to prevent it from deactivating. Given nature's frequent use of phospholipid vesicles as carriers, much attention has been paid to phospholipids as a vehicle for drug delivery. The physical chemistry of bilayer formation and nanoparticle encapsulation is complex, touching on fundamental properties of hydrophobicity. Understanding the design rules for particle synthesis and encapsulation is an active area of research. The aim of this review is to provide a perspective on what preparative guideposts have been empirically discovered and how these are related to theoretical understanding. In addition, we aim to summarize how modern theory is beginning to help guide the design of functional particles that can effectively cross biological membranes.

Ionic Liquid-Based Optical and Electrochemical Carbon Dioxide Sensors

PubMed Central

Behera, Kamalakanta; Pandey, Shubha; Kadyan, Anu; Pandey, Siddharth

2015-01-01

Due to their unusual physicochemical properties (e.g., high thermal stability, low volatility, high intrinsic conductivity, wide electrochemical windows and good solvating ability), ionic liquids have shown immense application potential in many research areas. Applications of ionic liquid in developing various sensors, especially for the sensing of biomolecules, such as nucleic acids, proteins and enzymes, gas sensing and sensing of various important ions, among other chemosensing platforms, are currently being explored by researchers worldwide. The use of ionic liquids for the detection of carbon dioxide (CO2) gas is currently a major topic of research due to the associated importance of this gas with daily human life. This review focuses on the application of ionic liquids in optical and electrochemical CO2 sensors. The design, mechanism, sensitivity and detection limit of each type of sensor are highlighted in this review. PMID:26690155

Stability of smectic phases in hard-rod mixtures

NASA Astrophysics Data System (ADS)

Martínez-Ratón, Yuri; Velasco, Enrique; Mederos, Luis

2005-09-01

Using density-functional theory, we have analyzed the phase behavior of binary mixtures of hard rods of different lengths and diameters. Previous studies have shown a strong tendency of smectic phases of these mixtures to segregate and, in some circumstances, to form microsegregated phases. Our focus in the present work is on the formation of columnar phases which some studies, under some approximations, have shown to become thermodynamically stable prior to crystallization. Specifically we focus on the relative stability between smectic and columnar phases, a question not fully addressed in previous work. Our analysis is based on two complementary perspectives: on the one hand, an extended Onsager theory, which includes the full orientational degrees of freedom but with spatial and orientational correlations being treated in an approximate manner; on the other hand, we formulate a Zwanzig approximation of fundamental-measure theory on hard parallelepipeds, whereby orientations are restricted to be only along three mutually orthogonal axes, but correlations are faithfully represented. In the latter case novel, complete phase diagrams containing regions of stability of liquid-crystalline phases are calculated. Our findings indicate that the restricted-orientation approximation enhances the stability of columnar phases so as to preempt smectic order completely while, in the framework of the extended Onsager model, with full orientational degrees of freedom taken into account, columnar phases may preempt a large region of smectic stability in some mixtures, but some smectic order still persists.

Microfluidic generation of particle-stabilized water-in-water emulsions

NASA Astrophysics Data System (ADS)

Abbasi, Niki; Navi, Maryam; Tsai, Scott

2017-11-01

We present a microfluidic platform that generates particle-stabilized water-in-water emulsions, using an aqueous two-phase system (ATPS) of polyethylene glycol (PEG) and Dextran (DEX). DEX droplets are generated passively at a flow focusing junction, in a continuous phase of PEG and carboxylated particles, using weak hydrostatic pressure to drive the flow. As DEX droplets travel inside the microfluidic device, carboxylated particles partition to the interface of the droplets. The number of particles partitioning to the interface of droplets increases as the droplets migrate downstream in the microchannel. As a result, the DEX droplets become stabilized against coalescence. We study the coverage and stability of the DEX droplets further downstream inside a reservoir, by changing the carboxylated particle concentration and the particle size. We anticipate that particle-stabilized water-in-water emulsions may have important biotechnological applications, due to their intrinsic biocompatibility compared to traditional particle-stabilized water-in-oil emulsions, for example for cell encapsulation.

Periodic waves of the Lugiato-Lefever equation at the onset of Turing instability.

PubMed

Delcey, Lucie; Haraguss, Mariana

2018-04-13

We study the existence and the stability of periodic steady waves for a nonlinear model, the Lugiato-Lefever equation, arising in optics. Starting from a detailed description of the stability properties of constant solutions, we then focus on the periodic steady waves which bifurcate at the onset of Turing instability. Using a centre manifold reduction, we analyse these Turing bifurcations, and prove the existence of periodic steady waves. This approach also allows us to conclude on the nonlinear orbital stability of these waves for co-periodic perturbations, i.e. for periodic perturbations which have the same period as the wave. This stability result is completed by a spectral stability result for general bounded perturbations. In particular, this spectral analysis shows that instabilities are always due to co-periodic perturbations.This article is part of the theme issue 'Stability of nonlinear waves and patterns and related topics'. © 2018 The Author(s).

Global stability of plane Couette flow beyond the energy stability limit

NASA Astrophysics Data System (ADS)

Fuentes, Federico; Goluskin, David

2017-11-01

This talk will present computations verifying that the laminar state of plane Couette flow is nonlinearly stable to all perturbations. The Reynolds numbers up to which this globally stability is verified are larger than those at which stability can be proven by the energy method, which is the typical method for demonstrating nonlinear stability of a fluid flow. This improvement is achieved by constructing Lyapunov functions that are more general than the energy. These functions are not restricted to being quadratic, and they are allowed to depend explicitly on the spectrum of the velocity field in the eigenbasis of the energy stability operator. The optimal choice of such a Lyapunov function is a convex optimization problem, and it can be constructed with computer assistance by solving a semidefinite program. This general method will be described in a companion talk by David Goluskin; the present talk focuses on its application to plane Couette flow.

Surface Stabilized InP/GaP/ZnS Quantum Dots with Mg Ions for WLED Application.

PubMed

Park, Joong Pill; Kim, Sang-Wook

2016-05-01

One of the most highlighted cadmium-free quantum dots (QDs), InP-based QDs, have improved their optical properties. However, InP-based QDs have some practical drawbacks, for example, stability, compared with CdSe-based QDs. Poor stability of InP-based QDs yields critical problems, such as agglomeration and photoluminescence quenching in light emitting diode (LED). It has to be solved for applications and most research has focused on thick outer shells as an effective solution. We introduced magnesium cations for improving stability of InP-based QDs. We applied very small amounts of Mg cations as surface stabilizers, as a result, stability of QDs is clearly improved. Then, QD based LED chips also yield improved values including RA of 84.4, CCT of 3799 K, and luminous efficiency of 129.57 Im/W, which are highly improved data compared with our previous results.

Methods and system for subsurface stabilization using jet grouting

DOEpatents

Loomis, Guy G.; Weidner, Jerry R.; Farnsworth, Richard K.; Gardner, Bradley M.; Jessmore, James J.

1999-01-01

Methods and systems are provided for stabilizing a subsurface area such as a buried waste pit for either long term storage, or interim storage and retrieval. A plurality of holes are drilled into the subsurface area with a high pressure drilling system provided with a drill stem having jet grouting nozzles. A grouting material is injected at high pressure through the jet grouting nozzles into a formed hole while the drill stem is withdrawn from the hole at a predetermined rate of rotation and translation. A grout-filled column is thereby formed with minimal grout returns, which when overlapped with other adjacent grout-filled columns encapsulates and binds the entire waste pit area to form a subsurface agglomeration or monolith of grout, soil, and waste. The formed monolith stabilizes the buried waste site against subsidence while simultaneously providing a barrier against contaminate migration. The stabilized monolith can be left permanently in place or can be retrieved if desired by using appropriate excavation equipment. The jet grouting technique can also be utilized in a pretreatment approach prior to in situ vitrification of a buried waste site. The waste encapsulation methods and systems are applicable to buried waste materials such as mixed waste, hazardous waste, or radioactive waste.

Quantification of Urban Environment's Role in Slope Stability for Landslide Events.

NASA Astrophysics Data System (ADS)

Bozzolan, E.; Holcombe, E.; Wagener, T.; Pianosi, F.

2017-12-01

The combination of a rapid and unplanned urban development with a likely future climate change could significantly affect landslide occurrences in the humid tropics, where rainfall events of high intensity and duration are the dominant trigger for landslide risk. The attention of current landslide hazard studies is largely focussed on natural slope processes based on combinations of environmental factors, excluding the role of urbanisation on slope stability. This project aims to understand the relative influence of urbanisation features on local slope stability and to translate the findings to a wider region. Individual slopes are firstly analysed with the software CHASM, a physically based model which combines soil hydrology and slope stability assessment. Instead of relying on existing records, generally lacking for landslides, ranges of plausible preparatory (such as slope, cohesion, friction angles), triggering (rainfall) and aggravating factors (deforestation, house density and water network) are defined and possible combinations of these factors are created by sampling from those ranges. The influence of urban features on site hydrology and stability mechanisms are evaluated and then implemented in denser urban contexts, characteristic of unplanned settlements. The results of CHASMS can be transferred to regional maps in order to identify the areas belonging to the triggering combinations of factors previously found. In this way, areas susceptible to landslides can be detected not only in terms of natural factors but also in relation to the degree of urbanisation. Realistic scenarios can be extrapolated from the areas considered and then analysed again with CHASM. This permits to adapt (and improve) the initial variability ranges of the factors, creating a general-specific cycle able to identify the landslide susceptibility regions and outline a hazard map. Once the triggers are understood, possible consequences can be assessed and mitigation strategies can be evaluated. The ability to define local urban rainfall threshold for landslide slope stability helps the decision-making process to prioritize the areas of interest and locally define the main causes of instability.

Advances of Researches on Improving the Stability of Foams by Nanoparticles

NASA Astrophysics Data System (ADS)

Wang, G.; Wang, K. L.; Lu, C. J.

2017-09-01

Recently, nano-tech made a change of traditional oil-gas exploration. Considering that foam fluid had a poor stability, investigators proposed to add nanoparticles to stabilize the foam fluid system. This paper described the mechanism of particles to improve the stability of the foam fluid in detail; and emphasized the synergistic effect between nanoparticles and surfactants and its effect on the foaming and foam stability of dispersions; and reviewed the latest applications of foam fluid that was stabilized by nanoparticle in enhancing oil-gas recovery, in which there are analysis that showed that the nanoparticles not only greatly increase the stability of the foam fluid, but also improve the efficiency of foam fluid; and lastly, forecasted the development of nanotechnology in petroleum areas.

Bank stability as a risk factor for pipeline infrastructure: a Scottish example

NASA Astrophysics Data System (ADS)

Maniatis, Georgios; Williams, Richard; Hoey, Trevor

2017-04-01

Bank erosion is a spatially variable process controlled by a number of factors that are interrelated (e.g. grain size, moisture content, organic content, vegetation, bank gradient). As a risk factor, bank erosion has been strongly connected to the failure of infrastructure that crosses or is adjacent to morphologically dynamic rivers. To manage this risk, comprehensive infrastructure asset management programs should include risk assessment of all structures that cross or are near a river. In Scotland, a significant proportion of cross-river infrastructure is pipe bridges, for both clean and waste water. These river crossings are maintained and managed by Scottish Water, a supplier responsible for a 48,000 km long drinking water pipe network and a 52,000 km long wastewater pipe network. Recently, Scottish Water began a comprehensive pipe bridge asset inspection program, which incorporates the acquisition of data to assess riverbank stability. The first step in the development of this database is the use of a prototype software application (a tablet app) which simplifies the surveying process by framing specific geomorphological questions and surveying tasks. As a result, the surveys can be conducted by inspectors with no specialist training in bank stability assessment and then reviewed by those with more expertise. Here, results are presented of a review of survey data, enabling the identification of the assets that are most at risk from bank erosion. The assessment focuses on assets from catchments in two contrasting areas of Scotland; the Hebrides and Glasgow. The uncertainty analysis focuses on input data quality and the variability of information available for desk based risk assessments using Geographic Information Systems (GIS). In parallel, considerations regarding the extension of this framework towards a unified strategy for assessing bank erosion are discussed such as the selection of a statistical framework and the catchment classification process. Finally, we discuss the process of knowledge exchange, where an industrial organization benefits from the scientific input and the academic organization benefits from the access to rapid surveying input at a country scale.

The effect of heat treatment on the stability of Nb 3Sn RRP-150/169 strands

DOE PAGES

Li, Pei; Turrioni, Daniele; Barzi, Emanuela; ...

2017-02-17

Here, the magnetic stability of superconductor strands and cables is a key issue in the successful building and operation of high-field accelerator magnets. In this paper, we report the study of a state-of-the-art 0.7 mm Nb 3Sn restacked-rod-process strand manufactured by Oxford Instrument Superconductor Technology. This conductor will be used in Rutherford cable for a 15-T Nb 3Sn dipole demonstrator being built at Fermi National Accelerator Laboratory. Particularly, this study focuses on the impact of varying heat treatment conditions on the stability of the strand. Both the stability against internal flux jumps and external thermal perturbations are studied.

The effect of heat treatment on the stability of Nb 3Sn RRP-150/169 strands

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Pei; Turrioni, Daniele; Barzi, Emanuela

Here, the magnetic stability of superconductor strands and cables is a key issue in the successful building and operation of high-field accelerator magnets. In this paper, we report the study of a state-of-the-art 0.7 mm Nb 3Sn restacked-rod-process strand manufactured by Oxford Instrument Superconductor Technology. This conductor will be used in Rutherford cable for a 15-T Nb 3Sn dipole demonstrator being built at Fermi National Accelerator Laboratory. Particularly, this study focuses on the impact of varying heat treatment conditions on the stability of the strand. Both the stability against internal flux jumps and external thermal perturbations are studied.

Enhancement of observability and protection of smart power system

NASA Astrophysics Data System (ADS)

Siddique, Abdul Hasib

It is important for a modern power grid to be smarter in order to provide reliable and sustainable supply of electricity. Traditional way of receiving data from the wired system is a very old and outdated technology. For a quicker and better response from the electric system, it is important to look at wireless systems as a feasible option. In order to enhance the observability and protection it is important to integrate wireless technology with the modern power system. In this thesis, wireless network based architecture for wide area monitoring and an alternate method for performing current measurement for protection of generators and motors, has been adopted. There are basically two part of this project. First part deals with the wide area monitoring of the power system and the second part focuses more on application of wireless technology from the protection point of view. A number of wireless method have been adopted in both the part, these includes Zigbee, analog transmission (Both AM and FM) and digital transmission. The main aim of our project was to propose a cost effective wide area monitoring and protection method which will enhance the observability and stability of power grid. A new concept of wireless integration in the power protection system has been implemented in this thesis work.

Future Forest Cover Change Scenarios with Implications for Landslide Risk: An Example from Buzau Subcarpathians, Romania

NASA Astrophysics Data System (ADS)

Malek, Žiga; Boerboom, Luc; Glade, Thomas

2015-11-01

This study focuses on future forest cover change in Buzau Subcarpathians, a landslide prone region in Romania. Past and current trends suggest that the area might expect a future increase in deforestation. We developed spatially explicit scenarios until 2040 to analyze the spatial pattern of future forest cover change and potential changes to landslide risk. First, we generated transition probability maps using the weights of evidence method, followed by a cellular automata allocation model. We performed expert interviews, to develop two future forest management scenarios. The Alternative scenario (ALT) was defined by 67 % more deforestation than the Business as Usual scenario (BAU). We integrated the simulated scenarios with a landslide susceptibility map. In both scenarios, most of deforestation was projected in areas where landslides are less likely to occur. Still, 483 (ALT) and 276 (BAU) ha of deforestation were projected on areas with a high-landslide occurrence likelihood. Thus, deforestation could lead to a local-scale increase in landslide risk, in particular near or adjacent to forestry roads. The parallel process of near 10 % forest expansion until 2040 was projected to occur mostly on areas with high-landslide susceptibility. On a regional scale, forest expansion could so result in improved slope stability. We modeled two additional scenarios with an implemented landslide risk policy, excluding high-risk zones. The reduction of deforestation on high-risk areas was achieved without a drastic decrease in the accessibility of the areas. Together with forest expansion, it could therefore be used as a risk reduction strategy.

Future Forest Cover Change Scenarios with Implications for Landslide Risk: An Example from Buzau Subcarpathians, Romania.

PubMed

Malek, Žiga; Boerboom, Luc; Glade, Thomas

2015-11-01

This study focuses on future forest cover change in Buzau Subcarpathians, a landslide prone region in Romania. Past and current trends suggest that the area might expect a future increase in deforestation. We developed spatially explicit scenarios until 2040 to analyze the spatial pattern of future forest cover change and potential changes to landslide risk. First, we generated transition probability maps using the weights of evidence method, followed by a cellular automata allocation model. We performed expert interviews, to develop two future forest management scenarios. The Alternative scenario (ALT) was defined by 67% more deforestation than the Business as Usual scenario (BAU). We integrated the simulated scenarios with a landslide susceptibility map. In both scenarios, most of deforestation was projected in areas where landslides are less likely to occur. Still, 483 (ALT) and 276 (BAU) ha of deforestation were projected on areas with a high-landslide occurrence likelihood. Thus, deforestation could lead to a local-scale increase in landslide risk, in particular near or adjacent to forestry roads. The parallel process of near 10% forest expansion until 2040 was projected to occur mostly on areas with high-landslide susceptibility. On a regional scale, forest expansion could so result in improved slope stability. We modeled two additional scenarios with an implemented landslide risk policy, excluding high-risk zones. The reduction of deforestation on high-risk areas was achieved without a drastic decrease in the accessibility of the areas. Together with forest expansion, it could therefore be used as a risk reduction strategy.

Stormwater Pollution Prevention Plan (SWPPP) for Coal Storage Area Stabilization Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Project and Design Engineering

2011-03-01

The scope of this project is to stabilize the abandoned coal storage area and redirect the storm water runoff from sanitary sewer system to the storm drain system. Currently, the existing storm water runoff is directed to a perimeter concrete drainage swale and collected in a containment basin. The collected water is then pumped to a treatment facility and after treatment, is discharged to the Y-12 sanitary sewer system. The existing drainage swale and collection basin along with silt fencing will be used during aggregate placement and grading to provide erosion and sediment control. Inlet protection will also be installedmore » around existing structures during the storm water diversion construction. This project scope will include the installation of a non-woven geotextile fabric and compacted mineral aggregate base (paving optional) to stabilize the site. The geotextile specifications are provided on the vendor cut sheets in Appendix B. The installation of a storm water collection/retention area will also be installed on the southern side of the site in accordance with EPA Technical Guidance on Implementing the Stormwater Runoff Requirements for federal Projects under Section 438 of the Energy Independence and Security Act. The total area to be disturbed is approximately 2.5 acres. The order of activities for this Stormwater Pollution Prevention Plan (SWPPP) will be: (1) post notice of coverage (NOC) in a prominent display near entrance of the site; (2) install rain gauge on site or contact Y-12 Plant Shift Superintendent daily for Met tower rain gauge readings; (3) install stabilized construction exit on site; (4) install silt fencing along perimeter as indicated on the attached site plan; (5) regrade site; (6) install geotextile fabric and compacted mineral aggregate base; (7) install catch basin inlet protection where required; (8) excavate and lower existing catch basin tops, re-grade and asphalt to drain; and (9) when all disturbed areas are re-stabilized, remove silt fencing and any other temporary erosion control.« less

Test system stability and natural variability of a Lemna gibba L. bioassay.

PubMed

Scherr, Claudia; Simon, Meinhard; Spranger, Jörg; Baumgartner, Stephan

2008-09-04

In ecotoxicological and environmental studies Lemna spp. are used as test organisms due to their small size, rapid predominantly vegetative reproduction, easy handling and high sensitivity to various chemicals. However, there is not much information available concerning spatial and temporal stability of experimental set-ups used for Lemna bioassays, though this is essential for interpretation and reliability of results. We therefore investigated stability and natural variability of a Lemna gibba bioassay assessing area-related and frond number-related growth rates under controlled laboratory conditions over about one year. Lemna gibba L. was grown in beakers with Steinberg medium for one week. Area-related and frond number-related growth rates (r(area) and r(num)) were determined with a non-destructive image processing system. To assess inter-experimental stability, 35 independent experiments were performed with 10 beakers each in the course of one year. We observed changes in growth rates by a factor of two over time. These did not correlate well with temperature or relative humidity in the growth chamber. In order to assess intra-experimental stability, we analysed six systematic negative control experiments (nontoxicant tests) with 96 replicate beakers each. Evaluation showed that the chosen experimental set-up was stable and did not produce false positive results. The coefficient of variation was lower for r(area) (2.99%) than for r(num) (4.27%). It is hypothesised that the variations in growth rates over time under controlled conditions are partly due to endogenic periodicities in Lemna gibba. The relevance of these variations for toxicity investigations should be investigated more closely. Area-related growth rate seems to be more precise as non-destructive calculation parameter than number-related growth rate. Furthermore, we propose two new validity criteria for Lemna gibba bioassays: variability of average specific and section-by-section segmented growth rate, complementary to average specific growth rate as the only validity criterion existing in guidelines for duckweed bioassays.

Test System Stability and Natural Variability of a Lemna Gibba L. Bioassay

PubMed Central

Scherr, Claudia; Simon, Meinhard; Spranger, Jörg; Baumgartner, Stephan

2008-01-01

Background In ecotoxicological and environmental studies Lemna spp. are used as test organisms due to their small size, rapid predominantly vegetative reproduction, easy handling and high sensitivity to various chemicals. However, there is not much information available concerning spatial and temporal stability of experimental set-ups used for Lemna bioassays, though this is essential for interpretation and reliability of results. We therefore investigated stability and natural variability of a Lemna gibba bioassay assessing area-related and frond number-related growth rates under controlled laboratory conditions over about one year. Methology/Principal Findings Lemna gibba L. was grown in beakers with Steinberg medium for one week. Area-related and frond number-related growth rates (r(area) and r(num)) were determined with a non-destructive image processing system. To assess inter-experimental stability, 35 independent experiments were performed with 10 beakers each in the course of one year. We observed changes in growth rates by a factor of two over time. These did not correlate well with temperature or relative humidity in the growth chamber. In order to assess intra-experimental stability, we analysed six systematic negative control experiments (nontoxicant tests) with 96 replicate beakers each. Evaluation showed that the chosen experimental set-up was stable and did not produce false positive results. The coefficient of variation was lower for r(area) (2.99%) than for r(num) (4.27%). Conclusions/Significance It is hypothesised that the variations in growth rates over time under controlled conditions are partly due to endogenic periodicities in Lemna gibba. The relevance of these variations for toxicity investigations should be investigated more closely. Area-related growth rate seems to be more precise as non-destructive calculation parameter than number-related growth rate. Furthermore, we propose two new validity criteria for Lemna gibba bioassays: variability of average specific and section-by-section segmented growth rate, complementary to average specific growth rate as the only validity criterion existing in guidelines for duckweed bioassays. PMID:18769541

Return to sport after patellar dislocation or following surgery for patellofemoral instability.

PubMed

Ménétrey, Jacques; Putman, Sophie; Gard, Suzanne

2014-10-01

Patellofemoral instability may occur in a young population as a result of injury during sporting activities. This review focuses on return to sport after one episode of dislocation treated no operatively and as well after surgery for chronic patellofemoral instability. With or without surgery, only two-thirds of patients return to sports at the same level as prior to injury. A high-quality rehabilitation programme using specific exercises is the key for a safe return to sporting activities. To achieve this goal, recovery of muscle strength and dynamic stability of the lower limbs is crucial. The focus should be directed to strengthen the quadriceps muscle and pelvic stabilizers, as well as lateral trunk muscle training. Patient education and regularly performed home exercises are other key factors that can lead to a successful return to sports. The criteria for a safe return to sports include the absence of pain, no effusion, a complete range of motion, almost symmetrical strength, and excellent dynamic stability. Level of evidence IV.

Letter to the Editor: On "Advantages and disadvantages of stiffness instructions when studying postural control" by C.T. Bonnet: You just can't win: Advantages and disadvantages of the postural stability requirement.

PubMed

Lajoie, Y; Richer, N; Jehu, D A; Polskaia, N; Saunders, D

2016-05-01

In the examination of postural control, instructions to stand as still as possible are common and promote a relatively unnatural sway pattern. The validity of the stability requirement is discussed in the present commentary in response to the discussion initiated by Cedrick T. Bonnet. The advantages of using the stability requirement include: evaluating unbiased postural control, reducing variability in postural sway, manipulating focus of attention, examining the ability to maintain an upright stance, and ecological validity of testing. The disadvantages include: constraining natural postural sway, increasing the complexity of the control condition, promoting an internal focus of attention, and reducing the ability to detect exploratory behaviour. After evaluating the aforementioned advantages and disadvantages, the present commentary suggests that researchers should strive to provide specific instructions to maintain feet, arm and eye position without specifically requiring participants to reduce their postural sway. Copyright © 2015 Elsevier B.V. All rights reserved.

Results of a multidisciplinary study in the Marmara Supersite, on-shore area: Büyükçekmece landslide

NASA Astrophysics Data System (ADS)

Coccia, Stella; Bigarré, Pascal; Ergintav, Semih; Ozel, Oguz; Yalcinkaya, Esref; Ozalabey, Serdar; Bourdeau, Céline; Martino, Salvatore; Lenti, Luca; Zucca, Francesco; Moro, Marco

2016-04-01

The MARsite project (Nov 2012-Avril 2016), one of the three SUPERSITE concept FP7 projects, deals with the definition of new directions in seismic hazard assessment through focused earth observation in the Marmara Supersite. This project gathers different research groups in a comprehensive monitoring activity developed in the Sea of Marmara Region. This region is one of the most densely populated parts of Europe and rated at high seismic risk level since the 1999 Izmit and Duzce devastating earthquakes. The 6th Work Package of MARsite project offered a very valuable frame to undertake simultaneous and complementary scientific investigations and studies to get deeper insight in the seismic and rainfall landslide topic, ranging from methodology to hazard assessment tool. This package focused on two sub-regional areas of high interest. First, the Avcilar-Beylikdüzü peninsula, located westwards of Istanbul, is a highly urbanized concentrated landslide prone area, showing high susceptibility to both rainfalls while affected by very significant seismic site effects. Second, the off-shore entrance of the Izmit Gulf, close to the termination of the surface rupture of the 1999 earthquake, that shows an important slump mass facing the Istanbul coastline. For the on-shore area, after refining the landslide inventory of the peninsula, one of the nine inventoried rototranslational landslides was chosen as pilot site, the Büyükçekmece landslide. This landslide has a continuous activity and a composite mechanism (including several secondary sliding surfaces); it moves at low velocity and involves sandy and clayey deposits of a local Cenozoic Succession damaging several infrastructures, such as buildings and roads. Various geophysical campaigns were carried out and then a field temporary multi-parameter monitoring was set up, composed of GPS-RTK, two seismic probes, thermometer, rain-gauge, moisture, etc.. Hyperspectral and Dinsar imagery technologies were also deployed to complete inventory and observational information. In order to analyze the slope stability conditions under seismic shaking, not-conventional pseudostatic slope stability analyses as well as numerical simulations via a finite difference code were performed. These last studies took advantage from the reconstruction of a detailed engineering-geological model on the basis of extensive geological and geomorphological field campaign and a vast drilling program undertaken by the Istanbul Metropolitan Area. According to these numerical simulation results the landslide mass has a high sensitivity to seismic waveforms enriched in low frequencies (<1.5Hz) causing the computed probability of reactivation to increase up to 58%. Based on the in situ multi-parametric monitoring system, the landslide moves continuously toward W; a double-net groundwater flow is revealed by the piezometer monitoring and preliminary co-relations between pore water pressures and rainfalls are evident in a seasonal and monthly time interval respectively.

Evolution of Biological Image Stabilization.

PubMed

Hardcastle, Ben J; Krapp, Holger G

2016-10-24

The use of vision to coordinate behavior requires an efficient control design that stabilizes the world on the retina or directs the gaze towards salient features in the surroundings. With a level gaze, visual processing tasks are simplified and behaviorally relevant features from the visual environment can be extracted. No matter how simple or sophisticated the eye design, mechanisms have evolved across phyla to stabilize gaze. In this review, we describe functional similarities in eyes and gaze stabilization reflexes, emphasizing their fundamental role in transforming sensory information into motor commands that support postural and locomotor control. We then focus on gaze stabilization design in flying insects and detail some of the underlying principles. Systems analysis reveals that gaze stabilization often involves several sensory modalities, including vision itself, and makes use of feedback as well as feedforward signals. Independent of phylogenetic distance, the physical interaction between an animal and its natural environment - its available senses and how it moves - appears to shape the adaptation of all aspects of gaze stabilization. Copyright © 2016 Elsevier Ltd. All rights reserved.

Enhanced thermal stability of a polymer solar cell blend induced by electron beam irradiation in the transmission electron microscope.

PubMed

Bäcke, Olof; Lindqvist, Camilla; de Zerio Mendaza, Amaia Diaz; Gustafsson, Stefan; Wang, Ergang; Andersson, Mats R; Müller, Christian; Kristiansen, Per Magnus; Olsson, Eva

2017-05-01

We show by in situ microscopy that the effects of electron beam irradiation during transmission electron microscopy can be used to lock microstructural features and enhance the structural thermal stability of a nanostructured polymer:fullerene blend. Polymer:fullerene bulk-heterojunction thin films show great promise for use as active layers in organic solar cells but their low thermal stability is a hindrance. Lack of thermal stability complicates manufacturing and influences the lifetime of devices. To investigate how electron irradiation affects the thermal stability of polymer:fullerene films, a model bulk-heterojunction film based on a thiophene-quinoxaline copolymer and a fullerene derivative was heat-treated in-situ in a transmission electron microscope. In areas of the film that exposed to the electron beam the nanostructure of the film remained stable, while the nanostructure in areas not exposed to the electron beam underwent large phase separation and nucleation of fullerene crystals. UV-vis spectroscopy shows that the polymer:fullerene films are stable for electron doses up to 2000kGy. Copyright © 2016 Elsevier B.V. All rights reserved.

Enhanced thermal stability of a polymer solar cell blend induced by electron beam irradiation in the transmission electron microscope.

PubMed

Bäcke, Olof; Lindqvist, Camilla; de Zerio Mendaza, Amaia Diaz; Gustafsson, Stefan; Wang, Ergang; Andersson, Mats R; Müller, Christian; Kristiansen, Per Magnus; Olsson, Eva

2017-02-01

We show by in situ microscopy that the effects of electron beam irradiation during transmission electron microscopy can be used to lock microstructural features and enhance the structural thermal stability of a nanostructured polymer:fullerene blend. Polymer:fullerene bulk-heterojunction thin films show great promise for use as active layers in organic solar cells but their low thermal stability is a hindrance. Lack of thermal stability complicates manufacturing and influences the lifetime of devices. To investigate how electron irradiation affects the thermal stability of polymer:fullerene films, a model bulk-heterojunction film based on a thiophene-quinoxaline copolymer and a fullerene derivative was heat-treated in-situ in a transmission electron microscope. In areas of the film that exposed to the electron beam the nanostructure of the film remained stable, while the nanostructure in areas not exposed to the electron beam underwent large phase separation and nucleation of fullerene crystals. UV-vis spectroscopy shows that the polymer:fullerene films are stable for electron doses up to 2000kGy. Copyright © 2017 Elsevier B.V. All rights reserved.

Novel methods of stabilization of Raney-Nickel catalyst for fuel-cell electrodes

NASA Astrophysics Data System (ADS)

Al-Saleh, M. A.; Sleem-Ur-Rahman; Kareemuddin, S. M. M. J.; Al-Zakri, A. S.

Two new methods of stabilizing Raney-Nickel (Raney-Ni) catalyst for making fuel-cell anodes were studied. In the first method, the catalyst was oxidized with aqueous H 2O 2 solution, while in the second, oxygen/air (O 2/air) was used in a slurry reactor. Effects of different concentrations of H 2O 2 (5-25 wt.%) and different pressures (10-20 psig) of gas were investigated. The stabilized catalyst was characterized using BET surface area, scanning electron microscopy (SEM) and X-ray diffraction (XRD). The catalyst was used in fuel-cell anodes and the electrochemical performance was determined in an alkaline half-cell. The results were compared with electrodes prepared using conventionally stabilized catalysts. The hydrogen peroxide-treated catalyst has higher BET surface area and produces electrodes with lower polarization. In addition to this, H 2O 2 treatment is convenient, fast and needs simple equipment which involves no instrumentation. Use of oxygen in a slurry reactor to stabilize the catalyst is also convenient but electrode performance is relatively poor.

FOREWORD: Focus on the Degradation and Stability of Polymers

NASA Astrophysics Data System (ADS)

Terano, Minoru

2008-06-01

Modern society is so reliant on polymers that products incorporating these macromolecules are almost 'invisible'. Polymers are indispensable materials used for manufacturing compact disks, clothes, lightweight airplanes, automobiles, footware and even the humble polystyrene boxes for packing our favorite hamburgers and fries. But, like many other materials, polymers degrade and become unstable, so a deeper understanding of the physical mechanisms responsible for degradation is necessary to address issues such as potential applications, recycling and the impact of polymer-products on the environment. In particular, polymers are highly vulnerable to oxidative degradation at elevated temperatures and in sunlight. Unfortunately, in spite of extensive research on polymer degradation, our knowledge is still incomplete. The analysis of polymer degradation and stability has recently become harder and more complicated because of the wider range of polymer applications, including blends and composites. Notably, composites with nanofillers are being studied for automotive, electrical and other industrial applications. With this background, the 1st International Symposium on Ultimate Stability of NanoStructured Polymers and Composites (NT2007) was held in October at the Japan Advanced Institute of Science and Technology in Ishikawa Prefecture. The meeting provided a forum to discuss advanced research achievements to resolve problems in this field of research. The papers selected for this focus issue describe recent discoveries on the stability, weatherability and flame retardancy of polymers, as well as providing an insight into degradation mechanisms of nanostructured polymers and composites. We hope that this focus issue will serve as a timely source of information about one of the most important topics in polymer science and related technologies.

Correlation of DCPI with deformation under proof roller loading to assess soft subgrade stabilization criterion : addendum to NCDOT final report 2011-05, entitled : "Field verification of undercut criteria and alternatives for subgrade stabilization in th

DOT National Transportation Integrated Search

2016-11-21

Work presented herein is an addendum to the final report for NCDOT Project 2011-05 entitled : Field Verification of Undercut Criteria and Alternatives for Subgrade Stabilization in the : Piedmont Area. The objective of the addendum work is to p...

Implications of the USGS analysis of slope stability at Sulphur Creek

Treesearch

L. M. Reid

1998-01-01

The slope stability equation and values for material properties recommended by USGS geologist Dr. Raymond Wilson were used to map the stability regime of the four units of THP 1-97-307 HUM and the two units of THP 1-96-413 HUM. When calculations are carried out for conditions without trees, results indicate that each unit includes significant areas that would be...

Youth Disciplinary Identification during Participation in Contemporary Project-Based Science Investigations in School

ERIC Educational Resources Information Center

Van Horne, Katie; Bell, Philip

2017-01-01

Recent science educational policy reform efforts call for a shift toward practice-focused instruction in kindergarten-Grade 12 science education. We argue that this focus on engaging students in epistemic practices of science opens up new possibilities for the design of learning environments that support the stabilization of learners'…

Dynamical stability of slip-stacking particles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eldred, Jeffrey; Zwaska, Robert

2014-09-01

We study the stability of particles in slip-stacking configuration, used to nearly double proton beam intensity at Fermilab. We introduce universal area factors to calculate the available phase space area for any set of beam parameters without individual simulation. We find perturbative solutions for stable particle trajectories. We establish Booster beam quality requirements to achieve 97% slip-stacking efficiency. We show that slip-stacking dynamics directly correspond to the driven pendulum and to the system of two standing-wave traps moving with respect to each other.

The relationship between the spatial scaling of biodiversity and ecosystem stability

PubMed Central

Delsol, Robin; Loreau, Michel; Haegeman, Bart

2018-01-01

Aim Ecosystem stability and its link with biodiversity have mainly been studied at the local scale. Here we present a simple theoretical model to address the joint dependence of diversity and stability on spatial scale, from local to continental. Methods The notion of stability we use is based on the temporal variability of an ecosystem-level property, such as primary productivity. In this way, our model integrates the well-known species–area relationship (SAR) with a recent proposal to quantify the spatial scaling of stability, called the invariability–area relationship (IAR). Results We show that the link between the two relationships strongly depends on whether the temporal fluctuations of the ecosystem property of interest are more correlated within than between species. If fluctuations are correlated within species but not between them, then the IAR is strongly constrained by the SAR. If instead individual fluctuations are only correlated by spatial proximity, then the IAR is unrelated to the SAR. We apply these two correlation assumptions to explore the effects of species loss and habitat destruction on stability, and find a rich variety of multi-scale spatial dependencies, with marked differences between the two assumptions. Main conclusions The dependence of ecosystem stability on biodiversity across spatial scales is governed by the spatial decay of correlations within and between species. Our work provides a point of reference for mechanistic models and data analyses. More generally, it illustrates the relevance of macroecology for ecosystem functioning and stability. PMID:29651225

Stabilization of Horseshoe Lake Road using Geofibers and Soil-Sement

DOT National Transportation Integrated Search

2012-04-03

One solution to reducing the cost of importing gravel in areas where available soils are predominately silts and : sands is to stabilize the local soils with geofibers and synthetic fluids. There have been several studies which : have evaluated impro...

The role of discharge variation in scaling of drainage area and food chain length in rivers

USGS Publications Warehouse

Sabo, John L.; Finlay, Jacques C.; Kennedy, Theodore A.; Post, David M.

2010-01-01

Food chain length (FCL) is a fundamental component of food web structure. Studies in a variety of ecosystems suggest that FCL is determined by energy supply, environmental stability, and/or ecosystem size, but the nature of the relationship between environmental stability and FCL, and the mechanism linking ecosystem size to FCL, remain unclear. Here we show that FCL increases with drainage area and decreases with hydrologic variability and intermittency across 36 North American rivers. Our analysis further suggests that hydrologic variability is the mechanism underlying the correlation between ecosystem size and FCL in rivers. Ecosystem size lengthens river food chains by integrating and attenuating discharge variation through stream networks, thereby enhancing environmental stability in larger river systems.

The role of discharge variation in scaling of drainage area and food chain length in rivers.

PubMed

Sabo, John L; Finlay, Jacques C; Kennedy, Theodore; Post, David M

2010-11-12

Food chain length (FCL) is a fundamental component of food web structure. Studies in a variety of ecosystems suggest that FCL is determined by energy supply, environmental stability, and/or ecosystem size, but the nature of the relationship between environmental stability and FCL, and the mechanism linking ecosystem size to FCL, remain unclear. Here we show that FCL increases with drainage area and decreases with hydrologic variability and intermittency across 36 North American rivers. Our analysis further suggests that hydrologic variability is the mechanism underlying the correlation between ecosystem size and FCL in rivers. Ecosystem size lengthens river food chains by integrating and attenuating discharge variation through stream networks, thereby enhancing environmental stability in larger river systems.

Hydrothermal synthesis of alpha- and beta-HgS nanostructures

NASA Astrophysics Data System (ADS)

Galain, Isabel; María, Pérez Barthaburu; Ivana, Aguiar; Laura, Fornaro

2017-01-01

We synthesized HgS nanostructures by the hydrothermal method in order to use them as electron acceptors in hybrid organic-inorganic solar cells. We employed different mercury sources (HgO and Hg(CH3COO)2) and polyvinylpyrrolidone (PVP) or hexadecanethiol (HDT) as stabilizing/capping agent for controlling size, crystallinity, morphology and stability of the obtained nanostructures. We also used thiourea as sulfur source, and a temperature of 180 °C during 6 h. Synthesized nanostructures were characterized by powder X-Ray Diffraction, Diffuse Reflectance Infrared Fourier Transform and Transmission Electron Microscopy. When PVP acts as stabilizing agent, the mercury source has influence on the size -but not in morphology- of the beta-HgS obtained nansostructures. HDT has control over nanostructures' size and depending on the relation Hg:HDT, we obtained a mixture of alpha and beta HgS which can be advantageous in the application in solar cells, due their absorption in different spectral regions. The smallest nanostructures obtained have a mean diameter of 20 nm when using HDT as capping agent. Also, we deposited the aforementioned nanostructures onto flat glass substrates by the spin coating technique as a first approach of an active layer of a solar cell. The depositions were characterized by atomic force microscopy. We obtained smaller particle deposition and higher particle density -but a lower area coverage (5%) - in samples with HDT as capping agent. This work presents promising results on nanostructures for future application on hybrid solar cells. Further efforts will be focused on the deposition of organic-inorganic layers.

ION-STABILIZED ELECTRON INDUCTION ACCELERATOR

DOEpatents

Finkelstein, D.

1960-03-22

A method and apparatus for establishing an ion-stabilized self-focusing relativistic electron beam from a plasma are reported. A plasma is introduced into a specially designed cavity by plasma guns, and a magnetic field satisfying betatron conditions is produced in the cavity by currents flowing in the highly conductive, non-magnetic surface of the cavity. This field forms the electron beam by induction from the plasma.

Coupled field effects in BWR stability simulations using SIMULATE-3K

DOE Office of Scientific and Technical Information (OSTI.GOV)

Borkowski, J.; Smith, K.; Hagrman, D.

1996-12-31

The SIMULATE-3K code is the transient analysis version of the Studsvik advanced nodal reactor analysis code, SIMULATE-3. Recent developments have focused on further broadening the range of transient applications by refinement of core thermal-hydraulic models and on comparison with boiling water reactor (BWR) stability measurements performed at Ringhals unit 1, during the startups of cycles 14 through 17.

A Remedy to Crises: Danish Special Operations Forces in Whole-of-Government Stabilization Engagements

DTIC Science & Technology

2016-06-01

bolstering fragile states and preventing violence from erupting: “we will focus on building the capacity of others to prevent the causes and consequences of...assisting fragile states as well, emphasizing violence prevention in its 2013 adopted policy on stabilization efforts in conflict-affected...practices for violence prevention and countermeasures. Second, this research considers DANSOF capabilities and recent DANSOF involvement in

Abstract Profiles of Structural Stability Point to Universal Tendencies, Family-Specific Factors, and Ancient Connections between Languages

PubMed Central

Dediu, Dan; Levinson, Stephen C.

2012-01-01

Language is the best example of a cultural evolutionary system, able to retain a phylogenetic signal over many thousands of years. The temporal stability (conservatism) of basic vocabulary is relatively well understood, but the stability of the structural properties of language (phonology, morphology, syntax) is still unclear. Here we report an extensive Bayesian phylogenetic investigation of the structural stability of numerous features across many language families and we introduce a novel method for analyzing the relationships between the “stability profiles” of language families. We found that there is a strong universal component across language families, suggesting the existence of universal linguistic, cognitive and genetic constraints. Against this background, however, each language family has a distinct stability profile, and these profiles cluster by geographic area and likely deep genealogical relationships. These stability profiles seem to show, for example, the ancient historical relationships between the Siberian and American language families, presumed to be separated by at least 12,000 years, and possible connections between the Eurasian families. We also found preliminary support for the punctuated evolution of structural features of language across families, types of features and geographic areas. Thus, such higher-level properties of language seen as an evolutionary system might allow the investigation of ancient connections between languages and shed light on the peopling of the world. PMID:23028843

Abstract profiles of structural stability point to universal tendencies, family-specific factors, and ancient connections between languages.

PubMed

Dediu, Dan; Levinson, Stephen C

2012-01-01

Language is the best example of a cultural evolutionary system, able to retain a phylogenetic signal over many thousands of years. The temporal stability (conservatism) of basic vocabulary is relatively well understood, but the stability of the structural properties of language (phonology, morphology, syntax) is still unclear. Here we report an extensive Bayesian phylogenetic investigation of the structural stability of numerous features across many language families and we introduce a novel method for analyzing the relationships between the "stability profiles" of language families. We found that there is a strong universal component across language families, suggesting the existence of universal linguistic, cognitive and genetic constraints. Against this background, however, each language family has a distinct stability profile, and these profiles cluster by geographic area and likely deep genealogical relationships. These stability profiles seem to show, for example, the ancient historical relationships between the Siberian and American language families, presumed to be separated by at least 12,000 years, and possible connections between the Eurasian families. We also found preliminary support for the punctuated evolution of structural features of language across families, types of features and geographic areas. Thus, such higher-level properties of language seen as an evolutionary system might allow the investigation of ancient connections between languages and shed light on the peopling of the world.

Digital processing of RF signals from optical frequency combs

NASA Astrophysics Data System (ADS)

Cizek, Martin; Smid, Radek; Buchta, Zdeněk.; Mikel, Břetislav; Lazar, Josef; Cip, Ondřej

2013-01-01

The presented work is focused on digital processing of beat note signals from a femtosecond optical frequency comb. The levels of mixing products of single spectral components of the comb with CW laser sources are usually very low compared to products of mixing all the comb components together. RF counters are more likely to measure the frequency of the strongest spectral component rather than a weak beat note. Proposed experimental digital signal processing system solves this problem by analyzing the whole spectrum of the output RF signal and using software defined radio (SDR) algorithms. Our efforts concentrate in two main areas: Firstly, using digital servo-loop techniques for locking free running continuous laser sources on single components of the fs comb spectrum. Secondly, we are experimenting with digital signal processing of the RF beat note spectrum produced by f-2f 1 technique used for assessing the offset and repetition frequencies of the comb, resulting in digital servo-loop stabilization of the fs comb. Software capable of computing and analyzing the beat-note RF spectrums using FFT and peak detection was developed. A SDR algorithm performing phase demodulation on the f- 2f signal is used as a regulation error signal source for a digital phase-locked loop stabilizing the offset frequency of the fs comb.

Digital processing of signals from femtosecond combs

NASA Astrophysics Data System (ADS)

Čížek, Martin; Šmíd, Radek; Buchta, Zdeněk.; Mikel, Břetislav; Lazar, Josef; Číp, Ondrej

2012-01-01

The presented work is focused on digital processing of beat note signals from a femtosecond optical frequency comb. The levels of mixing products of single spectral components of the comb with CW laser sources are usually very low compared to products of mixing all the comb components together. RF counters are more likely to measure the frequency of the strongest spectral component rather than a weak beat note. Proposed experimental digital signal processing system solves this problem by analyzing the whole spectrum of the output RF signal and using software defined radio (SDR) algorithms. Our efforts concentrate in two main areas: Firstly, we are experimenting with digital signal processing of the RF beat note spectrum produced by f-2f 1 technique and with fully digital servo-loop stabilization of the fs comb. Secondly, we are using digital servo-loop techniques for locking free running continuous laser sources on single components of the fs comb spectrum. Software capable of computing and analyzing the beat-note RF spectrums using FFT and peak detection was developed. A SDR algorithm performing phase demodulation on the f- 2f signal is used as a regulation error signal source for a digital phase-locked loop stabilizing the offset and repetition frequencies of the fs comb.

Understanding how biodiversity unfolds through time under neutral theory.

PubMed

Missa, Olivier; Dytham, Calvin; Morlon, Hélène

2016-04-05

Theoretical predictions for biodiversity patterns are typically derived under the assumption that ecological systems have reached a dynamic equilibrium. Yet, there is increasing evidence that various aspects of ecological systems, including (but not limited to) species richness, are not at equilibrium. Here, we use simulations to analyse how biodiversity patterns unfold through time. In particular, we focus on the relative time required for various biodiversity patterns (macroecological or phylogenetic) to reach equilibrium. We simulate spatially explicit metacommunities according to the Neutral Theory of Biodiversity (NTB) under three modes of speciation, which differ in how evenly a parent species is split between its two daughter species. We find that species richness stabilizes first, followed by species area relationships (SAR) and finally species abundance distributions (SAD). The difference in timing of equilibrium between these different macroecological patterns is the largest when the split of individuals between sibling species at speciation is the most uneven. Phylogenetic patterns of biodiversity take even longer to stabilize (tens to hundreds of times longer than species richness) so that equilibrium predictions from neutral theory for these patterns are unlikely to be relevant. Our results suggest that it may be unwise to assume that biodiversity patterns are at equilibrium and provide a first step in studying how these patterns unfold through time. © 2016 The Author(s).

Quantitative evaluation of lipid concentration in atherosclerotic plaque phantom by near-infrared multispectral angioscope at wavelengths around 1200 nm

NASA Astrophysics Data System (ADS)

Matsui, Daichi; Ishii, Katsunori; Awazu, Kunio

2015-07-01

Atherosclerosis is a primary cause of critical ischemic diseases like heart infarction or stroke. A method that can provide detailed information about the stability of atherosclerotic plaques is required. We focused on spectroscopic techniques that could evaluate the chemical composition of lipid in plaques. A novel angioscope using multispectral imaging at wavelengths around 1200 nm for quantitative evaluation of atherosclerotic plaques was developed. The angioscope consists of a halogen lamp, an indium gallium arsenide (InGaAs) camera, 3 optical band pass filters transmitting wavelengths of 1150, 1200, and 1300 nm, an image fiber having 0.7 mm outer diameter, and an irradiation fiber which consists of 7 multimode fibers. Atherosclerotic plaque phantoms with 100, 60, 20 vol.% of lipid were prepared and measured by the multispectral angioscope. The acquired datasets were processed by spectral angle mapper (SAM) method. As a result, simulated plaque areas in atherosclerotic plaque phantoms that could not be detected by an angioscopic visible image could be clearly enhanced. In addition, quantitative evaluation of atherosclerotic plaque phantoms based on the lipid volume fractions was performed up to 20 vol.%. These results show the potential of a multispectral angioscope at wavelengths around 1200 nm for quantitative evaluation of the stability of atherosclerotic plaques.

Roles of drizzle in a one-dimensional third-order turbulence closure model of the nocturnal stratus-topped marine boundary layer

NASA Technical Reports Server (NTRS)

Wang, Shouping; Wang, Qing

1994-01-01

This study focuses on the effects of drizzle in a one-dimensional third-order turbulence closure model of the nocturnal stratus-topped marine boundary layer. When the simulated drizzle rate is relatively small (maximum approximately equal to 0.6 mm/day), steady-state solutions are obtained. The boundary layer stabilizes essentially because drizzle causes evaporative cooling of the subcloud layer. This stabilization considerably reduces the buoyancy flux and turbulence kinetic energy below the stratus cloud. Thus, drizzle tends to decouple the cloud from the subcloud layer in the model, as suggested by many observational studies. In addition, the evaporation of drizzle in the subcloud layer creates small scattered clouds, which are likely to represent cumulus clouds, below the solid stratus cloud in the model. The sensitivity experiments show that these scattered clouds help maintain a coupled boundary layer. When the drizzle rate is relatively large (maximum approximately equal to 0.9 mm/day), the response of the model becomes transient with bursts in turbulent fluxes. This phenomenon is related to the formation of the scattered cloud layer below the solid stratus cloud. It appears that the model is inadequate to represent the heat and moisture transport by strong updrafts covering a small fractional area in cumulus convection.

Biomechanics and biomimetics in insect-inspired flight systems

PubMed Central

Liu, Hao; Ravi, Sridhar; Kolomenskiy, Dmitry; Tanaka, Hiroto

2016-01-01

Insect- and bird-size drones—micro air vehicles (MAV) that can perform autonomous flight in natural and man-made environments are now an active and well-integrated research area. MAVs normally operate at a low speed in a Reynolds number regime of 104–105 or lower, in which most flying animals of insects, birds and bats fly, and encounter unconventional challenges in generating sufficient aerodynamic forces to stay airborne and in controlling flight autonomy to achieve complex manoeuvres. Flying insects that power and control flight by flapping wings are capable of sophisticated aerodynamic force production and precise, agile manoeuvring, through an integrated system consisting of wings to generate aerodynamic force, muscles to move the wings and a control system to modulate power output from the muscles. In this article, we give a selective review on the state of the art of biomechanics in bioinspired flight systems in terms of flapping and flexible wing aerodynamics, flight dynamics and stability, passive and active mechanisms in stabilization and control, as well as flapping flight in unsteady environments. We further highlight recent advances in biomimetics of flapping-wing MAVs with a specific focus on insect-inspired wing design and fabrication, as well as sensing systems. This article is part of the themed issue ‘Moving in a moving medium: new perspectives on flight’. PMID:27528780

Advanced carbon materials/olivine LiFePO4 composites cathode for lithium ion batteries

NASA Astrophysics Data System (ADS)

Gong, Chunli; Xue, Zhigang; Wen, Sheng; Ye, Yunsheng; Xie, Xiaolin

2016-06-01

In the past two decades, LiFePO4 has undoubtly become a competitive candidate for the cathode material of the next-generation LIBs due to its abundant resources, low toxicity and excellent thermal stability, etc. However, the poor electronic conductivity as well as low lithium ion diffusion rate are the two major drawbacks for the commercial applications of LiFePO4 especially in the power energy field. The introduction of highly graphitized advanced carbon materials, which also possess high electronic conductivity, superior specific surface area and excellent structural stability, into LiFePO4 offers a better way to resolve the issue of limited rate performance caused by the two obstacles when compared with traditional carbon materials. In this review, we focus on advanced carbon materials such as one-dimensional (1D) carbon (carbon nanotubes and carbon fibers), two-dimensional (2D) carbon (graphene, graphene oxide and reduced graphene oxide) and three-dimensional (3D) carbon (carbon nanotubes array and 3D graphene skeleton), modified LiFePO4 for high power lithium ion batteries. The preparation strategies, structure, and electrochemical performance of advanced carbon/LiFePO4 composite are summarized and discussed in detail. The problems encountered in its application and the future development of this composite are also discussed.

Two-Dimensional Layered Double Hydroxides for Reactions of Methanation and Methane Reforming in C1 Chemistry

PubMed Central

Li, Panpan; Altaf, Naveed; Zhu, Mingyuan; Li, Jiangbing; Dai, Bin; Wang, Qiang

2018-01-01

CH4 as the paramount ingredient of natural gas plays an eminent role in C1 chemistry. CH4 catalytically converted to syngas is a significant route to transmute methane into high value-added chemicals. Moreover, the CO/CO2 methanation reaction is one of the potent technologies for CO2 valorization and the coal-derived natural gas production process. Due to the high thermal stability and high extent of dispersion of metallic particles, two-dimensional mixed metal oxides through calcined layered double hydroxides (LDHs) precursors are considered as the suitable supports or catalysts for both the reaction of methanation and methane reforming. The LDHs displayed compositional flexibility, small crystal sizes, high surface area and excellent basic properties. In this paper, we review previous works of LDHs applied in the reaction of both methanation and methane reforming, focus on the LDH-derived catalysts, which exhibit better catalytic performance and thermal stability than conventional catalysts prepared by impregnation method and also discuss the anti-coke ability and anti-sintering ability of LDH-derived catalysts. We believe that LDH-derived catalysts are promising materials in the heterogeneous catalytic field and provide new insight for the design of advance LDH-derived catalysts worthy of future research. PMID:29385064

The influence of mixture composition, adhesion promotor and compaction degree on the groove stability of grooved Marshall asphalt

NASA Astrophysics Data System (ADS)

Vuye, Cedric; Couscheir, Karolien; Lauriks, Leen; Van den bergh, Wim; Van Bouwel, Philippe

2017-09-01

After the first rehabilitation of runway 07R/25L in 2015, runway 01/19 was reconstructed in the summer of 2016, as part of a cycle where all runway pavements at Brussels airport are completely renovated each thirty years. The top layer is a Marshall asphalt with a polymer modified bitumen. To optimize the water drainage the central part of the runway (47 m wide) is grooved instead of applying an anti-skid layer. In this paper the focus is on the durability of the grooved top layer. Two different Marshall asphalt mixtures with a different maximum granulate size (10 mm or 14 mm) are compared, both in the laboratory and in a full-scale trial. In the laboratory the resistance against rutting and raveling are investigated for both mixtures with and without adhesion promotor, which did not show a positive effect. In the full-scale trial the compactability and impact of both a longer curing period and a variation in the degree of compaction on the groove stability is investigated for both mixtures using a heavy truck. No visual differences could be found except in areas which were undercompacted and showed more damage to the grooves.

Compact LWIR sensors using spatial interferometric technology (Conference Presentation)

NASA Astrophysics Data System (ADS)

Bingham, Adam L.; Lucey, Paul G.; Knobbe, Edward T.

2017-05-01

Recent developments in reducing the cost and mass of hyperspectral sensors have enabled more widespread use for short range compositional imaging applications. HSI in the long wave infrared (LWIR) is of interest because it is sensitive to spectral phenomena not accessible to other wavelengths, and because of its inherent thermal imaging capability. At Spectrum Photonics we have pursued compact LWIR hyperspectral sensors both using microbolometer arrays and compact cryogenic detector cameras. Our microbolometer-based systems are principally aimed at short standoff applications, currently weigh 10-15 lbs and feature sizes approximately 20x20x10 cm, with sensitivity in the 1-2 microflick range, and imaging times on the order of 30 seconds. Our systems that employ cryogenic arrays are aimed at medium standoff ranges such as nadir looking missions from UAVs. Recent work with cooled sensors has focused on Strained Layer Superlattice (SLS) technology, as these detector arrays are undergoing rapid improvements, and have some advantages compared to HgCdTe detectors in terms of calibration stability. These sensors include full on-board processing sensor stabilization so are somewhat larger than the microbolometer systems, but could be adapted to much more compact form factors. We will review our recent progress in both these application areas.

Understanding how biodiversity unfolds through time under neutral theory

PubMed Central

2016-01-01

Theoretical predictions for biodiversity patterns are typically derived under the assumption that ecological systems have reached a dynamic equilibrium. Yet, there is increasing evidence that various aspects of ecological systems, including (but not limited to) species richness, are not at equilibrium. Here, we use simulations to analyse how biodiversity patterns unfold through time. In particular, we focus on the relative time required for various biodiversity patterns (macroecological or phylogenetic) to reach equilibrium. We simulate spatially explicit metacommunities according to the Neutral Theory of Biodiversity (NTB) under three modes of speciation, which differ in how evenly a parent species is split between its two daughter species. We find that species richness stabilizes first, followed by species area relationships (SAR) and finally species abundance distributions (SAD). The difference in timing of equilibrium between these different macroecological patterns is the largest when the split of individuals between sibling species at speciation is the most uneven. Phylogenetic patterns of biodiversity take even longer to stabilize (tens to hundreds of times longer than species richness) so that equilibrium predictions from neutral theory for these patterns are unlikely to be relevant. Our results suggest that it may be unwise to assume that biodiversity patterns are at equilibrium and provide a first step in studying how these patterns unfold through time. PMID:26977066

Motivation of human resources for health: a case study at rural district level in Tanzania.

PubMed

Zinnen, Véronique; Paul, Elisabeth; Mwisongo, Aziza; Nyato, Daniel; Robert, Annie

2012-01-01

An increasing number of studies explore the association between financial and non-financial incentives and the retention of health workers in developing countries. This study aims to contribute to empirical evidence on human resource for health motivation factors to assist policy makers in promoting effective and realistic interventions. A cross-sectional survey was conducted in four rural Tanzanian districts to explore staff stability and health workers' motivation. Data were collected using qualitative and quantitative techniques, covering all levels and types of health facilities. Stability of staff was found to be quite high. Public institutions remained very attractive with better job security, salary and retirement benefits. Satisfaction over working conditions was very low owing to inadequate working equipment, work overload, lack of services, difficult environment, favouritism and 'empty promotions'. Positive incentives mentioned were support for career development and supportive supervision. Attracting new staff in rural areas appeared to be more difficult than retaining staff in place. The study concluded that strategies to better motivate health personnel should focus on adequate remuneration, positive working and living environment and supportive management. However, by multiplying health facilities, the latest Tanzanian human resource for health plan could jeopardize current positive results. Copyright © 2012 John Wiley & Sons, Ltd.

Pourbaix diagrams for the ternary system of iron-chromium-nickel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beverskog, B.; Puigdomenech, I.

1999-11-01

Pourbaix diagrams (potential-pH diagrams) for the ternary system of Fe-Cr-Ni at 25 C to 300 C were calculated. Extrapolation of thermochemical data to elevated temperatures was performed with the revised model of Helgeson-Kirkham-Flowers, which also allows uncharged aqueous complexes to be handled. The large stability of the bimetallic spinel oxides (trevorite [NiFe{sub 2}O{sub 4}], chromite [FeCr{sub 2}O{sub 4}], and nichromite [NiCr{sub 2}O{sub 4}]) is shown by their predominance areas on top of those for the single metal Pourbaix diagrams. NiFe{sub 2}O{sub 4} had the largest stability area of the spinels, and it covered the entire potential range for the stabilitymore » of water at intermediate pH. FeCr{sub 2}O{sub 4} had the smallest stability area and was the least stable of the bimetallic spinels. Results were discussed in connection with the different chemistries used in nuclear power reactors of the boiling water type.« less

In-tank precipitation facility (ITP) and H-Tank Farm (HTF) geotechnical report, WSRC-TR-95-0057, Revision 0, Volume 5

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

A geotechnical study has been completed in H-Area for the In-Tank Precipitation Facility (ITP) and the balance of the H-Area Tank Farm (HTF) at the Savannah River Site (SRS) in South Carolina. The study consisted of subsurface field exploration, field and laboratory testing, and engineering analyses. The purpose of these investigations is to evaluate the overall stability of the H-Area tanks under static and dynamic conditions. The objectives of the study are to define the site-specific geological conditions at ITP and HTF, obtain engineering properties for the assessment of the stability of the native soils and embankment under static andmore » dynamic loads (i.e., slope stability, liquefaction potential, and potential settlements), and derive properties for soil-structure interaction studies. This document (Volume 5) contains the laboratory test results for the In-Tank Precipitation Facility (ITP) and H-Tank Farm (HTF) Geotechnical Report.« less

Subsurface Characterization using Geophysical Seismic Refraction Survey for Slope Stabilization Design with Soil Nailing

NASA Astrophysics Data System (ADS)

Ashraf Mohamad Ismail, Mohd; Ng, Soon Min; Hazreek Zainal Abidin, Mohd; Madun, Aziman

2018-04-01

The application of geophysical seismic refraction for slope stabilization design using soil nailing method was demonstrated in this study. The potential weak layer of the study area is first identify prior to determining the appropriate length and location of the soil nail. A total of 7 seismic refraction survey lines were conducted at the study area with standard procedures. The refraction data were then analyzed by using the Pickwin and Plotrefa computer software package to obtain the seismic velocity profiles distribution. These results were correlated with the complementary borehole data to interpret the subsurface profile of the study area. It has been identified that layer 1 to 3 is the potential weak zone susceptible to slope failure. Hence, soil nails should be installed to transfer the tensile load from the less stable layer 3 to the more stable layer 4. The soil-nail interaction will provide a reinforcing action to the soil mass thereby increasing the stability of the slope.

Core stability training for injury prevention.

PubMed

Huxel Bliven, Kellie C; Anderson, Barton E

2013-11-01

Enhancing core stability through exercise is common to musculoskeletal injury prevention programs. Definitive evidence demonstrating an association between core instability and injury is lacking; however, multifaceted prevention programs including core stabilization exercises appear to be effective at reducing lower extremity injury rates. PUBMED WAS SEARCHED FOR EPIDEMIOLOGIC, BIOMECHANIC, AND CLINICAL STUDIES OF CORE STABILITY FOR INJURY PREVENTION (KEYWORDS: "core OR trunk" AND "training OR prevention OR exercise OR rehabilitation" AND "risk OR prevalence") published between January 1980 and October 2012. Articles with relevance to core stability risk factors, assessment, and training were reviewed. Relevant sources from articles were also retrieved and reviewed. Stabilizer, mobilizer, and load transfer core muscles assist in understanding injury risk, assessing core muscle function, and developing injury prevention programs. Moderate evidence of alterations in core muscle recruitment and injury risk exists. Assessment tools to identify deficits in volitional muscle contraction, isometric muscle endurance, stabilization, and movement patterns are available. Exercise programs to improve core stability should focus on muscle activation, neuromuscular control, static stabilization, and dynamic stability. Core stabilization relies on instantaneous integration among passive, active, and neural control subsystems. Core muscles are often categorized functionally on the basis of stabilizing or mobilizing roles. Neuromuscular control is critical in coordinating this complex system for dynamic stabilization. Comprehensive assessment and training require a multifaceted approach to address core muscle strength, endurance, and recruitment requirements for functional demands associated with daily activities, exercise, and sport.

Role of sulfates on highway heave in Lake County, Ohio.

DOT National Transportation Integrated Search

2014-01-01

Samples from borings in areas of heave on Route 2, Lake County, OH were analyzed for the amount, mineral form, : and distribution of sulfates. In addition, samples of non-stabilized (NSS) and cement-stabilized (CSS) soils from : three stations along ...

Rotation in vibration, optimization, and aeroelastic stability problems. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Kaza, K. R. V.

1974-01-01

The effects of rotation in the areas of vibrations, dynamic stability, optimization, and aeroelasticity were studied. The governing equations of motion for the study of vibration and dynamic stability of a rapidly rotating deformable body were developed starting from the nonlinear theory of elasticity. Some common features such as the limitations of the classical theory of elasticity, the choice of axis system, the property of self-adjointness, the phenomenon of frequency splitting, shortcomings of stability methods as applied to gyroscopic systems, and the effect of internal and external damping on stability in gyroscopic systems are identified and discussed, and are then applied to three specific problems.

China’s Currency: A Summary of the Economic Issues

DTIC Science & Technology

2008-01-09

lower-priced imports). Chinese officials view economic stability as critical to sustaining political stability; they fear an appreciated currency...development of rural areas, but they claim they want to proceed at a gradual pace to ensure economic stability . Implications of China’s Currency...Modifying Its Currency Policy Chinese officials argue that its currency policy is not meant to favor exports over imports, but instead to foster economic

Stability in Infant Frontal Asymmetry as a Predictor of Toddlerhood Internalizing and Externalizing Behaviors

PubMed Central

Smith, Cynthia L.; Bell, Martha Ann

2013-01-01

Stability in frontal brain electrical activity (i.e., electroencephalographic or EEG) asymmetry at 10 and 24 months was examined with respect to maternal ratings of internalizing and externalizing behaviors at 30 months in a sample of 48 children. Children with stable left frontal EEG asymmetry during infancy were rated higher in externalizing behaviors by their mothers, whereas children with stable right frontal EEG asymmetry were rated higher in internalizing behaviors. These findings highlight the need to focus on the early stability in physiological measures that may be implicated later in developing behavioral problems. PMID:20175143

Review of LFTs, LMIs, and mu. [Linear Fractional Transformations, Linear Matrix Inequalities

NASA Technical Reports Server (NTRS)

Doyle, John; Packard, Andy; Zhou, Kemin

1991-01-01

The authors present a tutorial overview of linear fractional transformations (LFTs) and the role of the structured singular value, mu, and linear matrix inequalities (LMIs) in solving LFT problems. The authors first introduce the notation for LFTs and briefly discuss some of their properties. They then describe mu and its connections with LFTs. They focus on two standard notions of robust stability and performance, mu stability and performance and Q stability and performance, and their relationship is discussed. Comparisons with the L1 theory of robust performance with structured uncertainty are considered.

Focus control enhancement and on-product focus response analysis methodology

NASA Astrophysics Data System (ADS)

Kim, Young Ki; Chen, Yen-Jen; Hao, Xueli; Samudrala, Pavan; Gomez, Juan-Manuel; Mahoney, Mark O.; Kamalizadeh, Ferhad; Hanson, Justin K.; Lee, Shawn; Tian, Ye

2016-03-01

With decreasing CDOF (Critical Depth Of Focus) for 20/14nm technology and beyond, focus errors are becoming increasingly critical for on-product performance. Current on product focus control techniques in high volume manufacturing are limited; It is difficult to define measurable focus error and optimize focus response on product with existing methods due to lack of credible focus measurement methodologies. Next to developments in imaging and focus control capability of scanners and general tool stability maintenance, on-product focus control improvements are also required to meet on-product imaging specifications. In this paper, we discuss focus monitoring, wafer (edge) fingerprint correction and on-product focus budget analysis through diffraction based focus (DBF) measurement methodology. Several examples will be presented showing better focus response and control on product wafers. Also, a method will be discussed for a focus interlock automation system on product for a high volume manufacturing (HVM) environment.

Improved Power System Stability Using Backtracking Search Algorithm for Coordination Design of PSS and TCSC Damping Controller.

PubMed

Niamul Islam, Naz; Hannan, M A; Mohamed, Azah; Shareef, Hussain

2016-01-01

Power system oscillation is a serious threat to the stability of multimachine power systems. The coordinated control of power system stabilizers (PSS) and thyristor-controlled series compensation (TCSC) damping controllers is a commonly used technique to provide the required damping over different modes of growing oscillations. However, their coordinated design is a complex multimodal optimization problem that is very hard to solve using traditional tuning techniques. In addition, several limitations of traditionally used techniques prevent the optimum design of coordinated controllers. In this paper, an alternate technique for robust damping over oscillation is presented using backtracking search algorithm (BSA). A 5-area 16-machine benchmark power system is considered to evaluate the design efficiency. The complete design process is conducted in a linear time-invariant (LTI) model of a power system. It includes the design formulation into a multi-objective function from the system eigenvalues. Later on, nonlinear time-domain simulations are used to compare the damping performances for different local and inter-area modes of power system oscillations. The performance of the BSA technique is compared against that of the popular particle swarm optimization (PSO) for coordinated design efficiency. Damping performances using different design techniques are compared in term of settling time and overshoot of oscillations. The results obtained verify that the BSA-based design improves the system stability significantly. The stability of the multimachine power system is improved by up to 74.47% and 79.93% for an inter-area mode and a local mode of oscillation, respectively. Thus, the proposed technique for coordinated design has great potential to improve power system stability and to maintain its secure operation.

The Karakum and Kyzylkum sand seas dynamics; mapping and palaeoclimatic interpretations

NASA Astrophysics Data System (ADS)

Maman, Shimrit; Blumberg, Dan G.; Tsoar, Haim; Porat, Naomi

2015-04-01

Sand seas are large basins in deserts that are mantled by wind-swept sand and that exhibit varying degrees of vegetation cover. Wilson (1973) was the first to globally map and classify sand seas. Beyond Wilson's maps, however, little research has been published regarding the Karakum and Kyzylkum sand seas of Central Asia. Wilson's maps delineate active ergs from inactive ergs based solely on precipitation. His assumption of annual average rainfall as a factor determining mobility vs. stability of sand seas is too simplistic and does not take into consideration other factors such as biogenic soil crusts and wind power, both of which are known to have major effects on the dynamics of sand dunes. Literature related to mapping and classifying the Central Asian ergs by remote sensing or sand sea classification state (stable/active) is lacking. Moreover, the palaeoclimatic significance of dunes in Central Asia is difficult to assess, as there has been few studies of dune stratigraphy and numerical ages are lacking. Optically stimulated luminescence (OSL) is a firm optical dating method that is used to determine the elapsed time since quartz grains were last exposed to sunlight, thus, their burial. Yet, absolute ages indicating mobilization and stabilization of these sands, are still inadequately known and are here under discussion. The broad concern of this research was to determine the dynamics of the Central Asian sand seas and study the palaeoclimatic changes that brought to their stabilization. As there are no reliable maps or aeolian discussion of these sands, establishment of a digital data base was initially conducted, focusing on identifying and mapping these sand seas. The vast area and inaccessibility make traditional mapping methods virtually impossible. A variety of space-borne imagery both optical and radar, with varying spectral and spatial resolutions was used. These images provided the basis for mapping sand distribution, dune forms, and vegetation cover. GIS analysis was performed in parallel with field work to obtain validation and verification. The remote sensing and GIS results show that these ergs are mostly stabilized, with the estimated sand mantled area for the Karakum desert ~260,000 km2, and for the Kyzylkum it is ~195,500 km2. Meteorological analysis of wind and precipitation data indicate a low wind power environment (DP< 200) and sufficient rainfall (>100 mm) to support vegetation. Thus, these sands are indicative of past periods during which the climate in this region was different than today, enabling aeolian sand activity. Optically stimulated luminescence ages derived from the upper meter of the interdune of 14 exposed sections from both ergs, indicate sand stabilization during the mid-Holocene. This stabilization is understood to reflect a transition to a warmer, wetter, and less windy climate that generally persisted until today. The OSL ages, coupled with a compilation of regional palaeoclimatic data, corroborate and reinforce the previously proposed Mid-Holocene Liavliakan phase, known to reflect a warmer, wetter, and less windy climate that persists until today and resulted in dune stabilization around the Mid-Holocene.

Pharmacovigilance in Space: Stability Payload Compliance Procedures

NASA Technical Reports Server (NTRS)

Daniels, Vernie R.; Putcha, Lakshmi

2007-01-01

Pharmacovigilance is the science of, and activities relating to the detection, assessment, understanding, and prevention of drug-related problems. Over the lase decade, pharmacovigilance activities have contributed to the development of numerous technological and conventional advances focused on medication safety and regulatory intervention. The topics discussed include: 1) Proactive Pharmacovigilance; 2) A New Frontier; 3) Research Activities; 4) Project Purpose; 5) Methods; 6) Flight Stability Kit Components; 7) Experimental Conditions; 8) Research Project Logistics; 9) Research Plan; 10) Pharmaceutical Stability Research Project Pharmacovigilance Aspects; 11) Security / Control; 12) Packaging/Containment Actions; 13) Shelf-Life Assessments; 14) Stability Assessment Parameters; 15) Chemical Content Analysis; 16) Preliminary Results; 17) Temperature/Humidity; 18) Changes in PHysical and Chemical Assessment Parameters; 19) Observations; and 20) Conclusions.

Stability Analysis of Landslide on the R1 Expressway by Limit Equilibrium and Finite Element Methods

NASA Astrophysics Data System (ADS)

Janták, Viktor

2017-12-01

The most difficult problem by designing the superior infrastructure is tracing the expressways and higways in an environment of Quaternary and Neogene complexes of finegrained cohesive and non-cohesive soils. At the last time the typical examples are stability problems on the R1 Nitra - Tekovské Nemce Expressway. The article is focused on the description of reasons of stability loss in the deep earth cut in the 79,000 km of expressway R1, the course of the landslide, slide correction and especially slope-stability assessment before and after the occurrence of slope failures by limit equilibrium and finite elements methods by comparing the behaviour of the slope in the various model situations.

Interdisciplinary challenges in the study of power grid resilience and stability and their relation to extreme weather events

NASA Astrophysics Data System (ADS)

Heitzig, J.; Fujiwara, N.; Aihara, K.; Kurths, J.

2014-10-01

This topical issue collects contributions to the interdisciplinary study of power grid stability in face of increasing volatility of energy production and consumption due to increasing renewable energy infeed and changing climatic conditions. The individual papers focus on different aspects of this field and bring together modern achievements from various disciplines, in particular complex systems science, nonlinear data analysis, control theory, electrical engineering, and climatology. Main topics considered here are prediction and volatility of renewable infeed, modelling and theoretical analysis of power grid topology, dynamics and stability, relationships between stability and complex network topology, and improvements via topological changes or control. Impacts for the design of smart power grids are discussed in detail.

Advances in neglected tropical disease vaccines: Developing relative potency and functional assays for the Na-GST-1/Alhydrogel hookworm vaccine

PubMed Central

Brelsford, Jill B.; Plieskatt, Jordan L.; Yakovleva, Anna; Jariwala, Amar; Keegan, Brian P.; Peng, Jin; Xia, Pengjun; Li, Guangzhao; Campbell, Doreen; Periago, Maria Victoria; Correa-Oliveira, Rodrigo; Bottazzi, Maria Elena; Hotez, Peter J.

2017-01-01

A new generation of vaccines for the neglected tropical diseases (NTDs) have now advanced into clinical development, with the Na-GST-1/Alhydrogel Hookworm Vaccine already being tested in Phase 1 studies in healthy adults. The current manuscript focuses on the often overlooked critical aspects of NTD vaccine product development, more specifically, vaccine stability testing programs. A key measure of vaccine stability testing is "relative potency" or the immunogenicity of the vaccine during storage. As with most NTD vaccines, the Na-GST-1/Alhydrogel Hookworm Vaccine was not developed by attenuation or inactivation of the pathogen (Necator americanus), so conventional methods for measuring relative potency are not relevant for this investigational product. Herein, we describe a novel relative potency testing program and report for the first time on the clinical lot of this NTD vaccine during its first 60 months of storage at 2–8°C. We also describe the development of a complementary functional assay that measures the ability of IgG from animals or humans immunized with Na-GST-1/Alhydrogel to neutralize this important hookworm enzyme. While 90% inhibition of the catalytic activity of Na-GST-1 was achieved in animals immunized with Na-GST-1/Alhydrogel, lower levels of inhibition were observed in immunized humans. Moreover, anti-Na-GST-1 antibodies from volunteers in non-hookworm endemic areas were better able to inhibit catalytic activity than anti-Na-GST-1 antibodies from volunteers resident in hookworm endemic areas. The results described herein provide the critical tools for the product development of NTD vaccines. PMID:28192438

Influence of damage and basal friction on the grounding line dynamics

NASA Astrophysics Data System (ADS)

Brondex, Julien; Gagliardini, Olivier; Gillet-Chaulet, Fabien; Durand, Gael

2016-04-01

The understanding of grounding line dynamics is a major issue in the prediction of future sea level rise due to ice released from polar ice sheets into the ocean. This dynamics is complex and significantly affected by several physical processes not always adequately accounted for in current ice flow models. Among those processes, our study focuses on ice damage and evolving basal friction conditions. Softening of the ice due to damaging processes is known to have a strong impact on its rheology by reducing its viscosity and therefore promoting flow acceleration. Damage creates where shear stresses are high enough which is usually the case at shear margins and in the vicinity of pinning points in contact with ice-shelves. Those areas are known to have a buttressing effect on ice shelves contributing to stabilize the grounding line. We aim at evaluating the extent to which this stabilizing effect is hampered by damaging processes. Several friction laws have been proposed by various author to model the contact between grounded-ice and bedrock. Among them, Coulomb-type friction laws enable to account for reduced friction related to low effective pressure (the ice pressure minus the water pressure). Combining such a friction law to a parametrization of the effective pressure accounting for the fact that the area upstream the grounded line is connected to the ocean, is expected to have a significant impact on the grounding line dynamics. Using the finite-element code Elmer/Ice within which both the Coulomb-type friction law, the effective pressure parametrization and the damage model have been implemented, the goal of this study is to investigate the sensitivity of the grounding line dynamics to damage and to an evolving basal friction. The relative importance between those two processes on the grounding line dynamics is addressed as well.

Proportional integral derivative, modeling and ways of stabilization for the spark plasma sintering process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Manière, Charles; Lee, Geuntak; Olevsky, Eugene A.

The stability of the proportional–integral–derivative (PID) control of temperature in the spark plasma sintering (SPS) process is investigated. The PID regulations of this process are tested for different SPS tooling dimensions, physical parameters conditions, and areas of temperature control. It is shown that the PID regulation quality strongly depends on the heating time lag between the area of heat generation and the area of the temperature control. Tooling temperature rate maps are studied to reveal potential areas for highly efficient PID control. The convergence of the model and experiment indicates that even with non-optimal initial PID coefficients, it is possiblemore » to reduce the temperature regulation inaccuracy to less than 4 K by positioning the temperature control location in highly responsive areas revealed by the finite-element calculations of the temperature spatial distribution.« less

Proportional integral derivative, modeling and ways of stabilization for the spark plasma sintering process

DOE PAGES

Manière, Charles; Lee, Geuntak; Olevsky, Eugene A.

2017-04-21

The stability of the proportional–integral–derivative (PID) control of temperature in the spark plasma sintering (SPS) process is investigated. The PID regulations of this process are tested for different SPS tooling dimensions, physical parameters conditions, and areas of temperature control. It is shown that the PID regulation quality strongly depends on the heating time lag between the area of heat generation and the area of the temperature control. Tooling temperature rate maps are studied to reveal potential areas for highly efficient PID control. The convergence of the model and experiment indicates that even with non-optimal initial PID coefficients, it is possiblemore » to reduce the temperature regulation inaccuracy to less than 4 K by positioning the temperature control location in highly responsive areas revealed by the finite-element calculations of the temperature spatial distribution.« less

Recent advances in preparative electrophoresis

NASA Technical Reports Server (NTRS)

Mosher, Richard A.; Thormann, Wolfgang; Egen, Ned B.; Couasnon, Pascal; Sammons, David W.

1987-01-01

Various approaches for preparative electrophoresis, and three new instruments for preparative electrophoresis are discussed. Consideration is given to isoelectric focusing, isotachophoresis, and zone electrophoresis, three gel-based electrophoresis methods. The design, functions, and performance of the Elphor VaP 21 device of Hannig (1982), the shear-stabilized BIOSTREAM separator of Thompson (1983), and the recycling isoelectric focusing device are described.

The Superconducting Cavity Stabilized Oscillator

NASA Technical Reports Server (NTRS)

Turneaure, J. P.; Buchman, Saps; Lipa, John

1997-01-01

Superconducting Cavity Stabilized Oscillators (SCSOs) have produced the most stable clocks to date for integration times between 10(exp 2) and 10(exp 3) seconds, achieving a fractional frequency stability of 2 x 10(exp -16) for a sampling time of 100 s. The principal contributors to cavity frequency variations are: (1) acceleration effects due to gravity and vibrations; (2) temperature variations; (3) variations in the energy stored in the cavity; and (4) noise introduced by the frequency stabilization circuit. We discuss the prospects for improvements in all these areas for both ground-based and space-based SCSOs, which may lead to SCSOs with fractional frequency stabilities below 10(exp -17). SCSOs of this frequency stability will be useful for testing fundamental physical principles.

Promoting health: media advocacy opportunities in English- and Spanish-language masthead editorials.

PubMed

Lingas, Elena O

2013-01-01

This study examines two newspapers' editorial coverage of issues related to the Healthy People 2010 focus areas and compares the two newspapers. A qualitative study. Two Los Angeles, California, newspapers. The masthead editorials of the Los Angeles Times and La Opinión in the year following the release of Healthy People 2010. A structured data abstraction instrument was used for descriptive coding. Correspondence to 1 of the 28 Healthy People 2010 focus areas determined whether domestic editorials were about health. An ethnographic content analysis. There were 1075 editorials from the Los Angeles Times and 361 from La Opinión; 17% were focused on domestic health issues. Three Healthy People 2010 focus areas dominated: Environmental Health, Injury and Violence Prevention, and Access to Quality Health Services. Ten focus areas did not receive a single mention in the Los Angeles Times, and 19 focus areas lacked editorials in La Opinión. Editorial writers regularly tackled issues related to a Healthy People 2010 focus area. Public health practitioners can meet with their local newspaper editorial board and discuss the nation's health objectives as manifested by Healthy People 2020 and the National Prevention Strategy, thereby promoting policies that support individual and population health.

Preferred retinal locus in macular disease: characteristics and clinical implications.

PubMed

Greenstein, Vivienne C; Santos, Rodrigo A V; Tsang, Stephen H; Smith, R Theodore; Barile, Gaetano R; Seiple, William

2008-10-01

To investigate the location and fixation stability of preferred retinal locations (PRLs) in patients with macular disease, and the relationship among areas of abnormal fundus autofluorescence, the PRL and visual sensitivity. Fifteen patients (15 eyes) were studied. Seven had Stargardt disease, 1 bull's eye maculopathy, 5 age-related macular degeneration, 1 Best disease, and 1 pattern dystrophy. All tested eyes had areas of abnormal fundus autofluorescence. The PRL was evaluated with fundus photography and the Nidek microperimeter. Visual field sensitivity was measured with the Nidek microperimeter. Of the 15 eyes, 4 had foveal and 11 had eccentric fixation. Eccentric PRLs were above the atrophic lesion and their stability did not depend on the degree of eccentricity from the fovea. Visual sensitivity was markedly decreased in locations corresponding to hypofluorescent areas. Sensitivity was not decreased in hyperfluorescent areas corresponding to flecks but was decreased if hyperfluorescence was in the form of dense annuli. Eccentric PRLs were in the superior retina in regions of normal fundus autofluorescence. Fixation stability was not correlated with the degree of eccentricity from the fovea. To assess the outcomes of treatment trials it is important to use methods that relate retinal morphology to visual function.

Field verification of undercut criteria and alternatives for subgrade stabilization in the Piedmont area.

DOT National Transportation Integrated Search

2016-02-15

Work performed in this research project was in support of the effort by the North Carolina Department of Transportation to develop criteria to discern the need for undercutting soft soils and the adequacy of the subgrade after stabilization measures ...

A study of static stability of airships

NASA Technical Reports Server (NTRS)

Rizzo, Frank

1924-01-01

The first section deals with the theoretical side of statical stability of airships in general. The second section deals with preliminary tests of the model and experiments for the determination of effects due to change of tail area, aspect ratio, tail form, and tail thickness.

Stabilization of red blood cells by the plasticizer, diethylhexylphthalate.

PubMed

Horowitz, B; Stryker, M H; Waldman, A A; Woods, K R; Gass, J D; Drago, J

1985-01-01

The red blood cells of blood stored in containers made of polyvinylchloride (PVC) film are osmotically more stable and lose on average about 1/3 less hemoglobin than when blood is stored in another plastic [poly-(ethylene-co-ethyl acrylate); EEA]. The stability of uniform volumes of stored red blood cells varies directly with PVC surface area, whereas changes in EEA surface area have comparatively little or no effect. PVC contains high concentrations of the plasticizer, diethylhexylphthalate (DEHP), known to migrate into blood and to have a high potential for toxicity. To determine if DEHP could be the red cell stabilizing agent in PVC, whole blood was stored in containers made from EEA into which was incorporated varying amounts of DEHP. Incorporation of DEHP into EEA significantly reduced erythrocyte osmotic fragility (p = 0.01). The degree of reduced fragility correlated with the level of DEHP in the cell phase implicating DEHP in PVC containers as the stabilizing agent for red cells.

An invariability-area relationship sheds new light on the spatial scaling of ecological stability.

PubMed

Wang, Shaopeng; Loreau, Michel; Arnoldi, Jean-Francois; Fang, Jingyun; Rahman, K Abd; Tao, Shengli; de Mazancourt, Claire

2017-05-19

The spatial scaling of stability is key to understanding ecological sustainability across scales and the sensitivity of ecosystems to habitat destruction. Here we propose the invariability-area relationship (IAR) as a novel approach to investigate the spatial scaling of stability. The shape and slope of IAR are largely determined by patterns of spatial synchrony across scales. When synchrony decays exponentially with distance, IARs exhibit three phases, characterized by steeper increases in invariability at both small and large scales. Such triphasic IARs are observed for primary productivity from plot to continental scales. When synchrony decays as a power law with distance, IARs are quasilinear on a log-log scale. Such quasilinear IARs are observed for North American bird biomass at both species and community levels. The IAR provides a quantitative tool to predict the effects of habitat loss on population and ecosystem stability and to detect regime shifts in spatial ecological systems, which are goals of relevance to conservation and policy.

Teaching Potential Energy Functions and Stability with Slap Bracelets

NASA Astrophysics Data System (ADS)

Van Hook, Stephen J.

2005-10-01

The slap bracelet, an inexpensive child's toy, makes it easy to engage students in hands-on exploration of potential energy curves as well as of stable, unstable, and meta-stable states. Rather than just observing the teacher performing a demonstration, the students can manipulate the equipment themselves and make their own observations, which are then pooled to focus a class discussion on potential energy functions and stability.

Application of Enlisted Force Retention Levels and Career Field Stability

DTIC Science & Technology

2017-03-23

a priority. This research focuses on modeling the enlisted force retention behavior. Specifically, this research examines a statistically based ...and must be manually corrected. Air Force Manpower , Personnel and Services (AF/A1PF) supplied the data used in this research . The data was...Stability Jamie T. Zimmerman Follow this and additional works at: https://scholar.afit.edu/etd Part of the Operational Research Commons This Thesis is

Similarity Metrics for Closed Loop Dynamic Systems

NASA Technical Reports Server (NTRS)

Whorton, Mark S.; Yang, Lee C.; Bedrossian, Naz; Hall, Robert A.

2008-01-01

To what extent and in what ways can two closed-loop dynamic systems be said to be "similar?" This question arises in a wide range of dynamic systems modeling and control system design applications. For example, bounds on error models are fundamental to the controller optimization with modern control design methods. Metrics such as the structured singular value are direct measures of the degree to which properties such as stability or performance are maintained in the presence of specified uncertainties or variations in the plant model. Similarly, controls-related areas such as system identification, model reduction, and experimental model validation employ measures of similarity between multiple realizations of a dynamic system. Each area has its tools and approaches, with each tool more or less suited for one application or the other. Similarity in the context of closed-loop model validation via flight test is subtly different from error measures in the typical controls oriented application. Whereas similarity in a robust control context relates to plant variation and the attendant affect on stability and performance, in this context similarity metrics are sought that assess the relevance of a dynamic system test for the purpose of validating the stability and performance of a "similar" dynamic system. Similarity in the context of system identification is much more relevant than are robust control analogies in that errors between one dynamic system (the test article) and another (the nominal "design" model) are sought for the purpose of bounding the validity of a model for control design and analysis. Yet system identification typically involves open-loop plant models which are independent of the control system (with the exception of limited developments in closed-loop system identification which is nonetheless focused on obtaining open-loop plant models from closed-loop data). Moreover the objectives of system identification are not the same as a flight test and hence system identification error metrics are not directly relevant. In applications such as launch vehicles where the open loop plant is unstable it is similarity of the closed-loop system dynamics of a flight test that are relevant.

The Influence of Planetary Mass on the Dynamical Lifetime of Planetary Systems

NASA Technical Reports Server (NTRS)

Lissauer, J. J.; Duncan, M. J.; Young, Richard E. (Technical Monitor)

1997-01-01

Recent numerical and analytic studies of planetary orbits have demonstrated the importance of resonances and chaos in destabilizing planetary systems. Newton's "clockwork" description of regular, predictable planetary orbits has been replaced by a view in which many systems can have long but finite lifetimes. This new knowledge has altered our perceptions of the later stages of planetary growth and of the stability of planetary systems. Stability criteria are inexact and time dependent. Most previous studies have focused on the effects in initial planetary orbits on the stability of the system. We are conducting an investigation which focuses on the dependence of stability criteria on planetary mass. Synthetic systems are created by increasing the masses of the planets in our Solar System or of the moons of a particular planet; these systems are then integrated until orbit crossing occurs. We have found that over some ranges, the time until orbit crossing varies to a good approximation as a power clothe factor by which the masses of the secondaries arc increased; some scatter occurs as a consequence of vie chaotic nature of orbital evolution. The slope of this power law varies substantially from system to system, and for moons it is mildly dependent on the inclusion of the planet's quadrupole moment in the gravitational potential.

Towards the Rational Design of Nanoparticle Catalysts

NASA Astrophysics Data System (ADS)

Dash, Priyabrat

This research is focused on development of routes towards the rational design of nanoparticle catalysts. Primarily, it is focused on two main projects; (1) the use of imidazolium-based ionic liquids (ILs) as greener media for the design of quasi-homogeneous nanoparticle catalysts and (2) the rational design of heterogeneous-supported nanoparticle catalysts from structured nanoparticle precursors. Each project has different studies associated with the main objective of the design of nanoparticle catalysts. In the first project, imidazolium-based ionic liquids have been used for the synthesis of nanoparticle catalysts. In particular, studies on recyclability, reuse, mode-of-stability, and long-term stability of these ionic-liquid supported nanoparticle catalysts have been done; all of which are important factors in determining the overall "greenness" of such synthetic routes. Three papers have been published/submitted for this project. In the first publication, highly stable polymer-stabilized Au, Pd and bimetallic Au-Pd nanoparticle catalysts have been synthesized in imidazolium-based 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM]PF6) ionic liquid (Journal of Molecular Catalysis A: Chemical, 2008, 286, 114). The resulting nanoparticles were found to be effective and selective quasi-homogeneous catalysts towards a wide-range of hydrogenation reactions and the catalyst solution was reused for further catalytic reactions with minimal loss in activity. The synthesis of very pure and clean ILs has allowed a platform to study the effects of impurities in the imidazolium ILs on nanoparticle stability. In a later study, a new mode of stabilization was postulated where the presence of low amounts of 1-methylimidazole has substantial effects on the resulting stability of Au and Pd-Au nanoparticles in these ILs (Chemical Communications, 2009, 812). In further continuation of this study, a comparative study involving four stabilization protocols for nanoparticle stabilization in BMIMPF6 IL is described, and have shown that nanoparticle stability and catalytic activity of nanoparticles is dependent on the overall stability of the nanoparticles towards aggregation (manuscript submitted). The second major project is focused on synthesizing structurally well-defined supported catalysts by incorporating the nanoparticle precursors (both alloy and core shell) into oxide frameworks (TiO2 and Al2O 3), and examining their structure-property relationships and catalytic activity. a full article has been published on this project (Journal of Physical Chemistry C, 2009, 113, 12719) in which a route to rationally design supported catalysts from structured nanoparticle precursors with precise control over size, composition, and internal structure of the nanoparticles has been shown. In a continuation of this methodology for the synthesis of heterogeneous catalysts, efforts were carried out to apply the same methodology in imidazolium-based ILs as a one-pot media for the synthesis of supported-nanoparticle heterogeneous catalysts via the trapping of pre-synthesized nanoparticles into porous inorganic oxide materials. Nanoparticle catalysts in highly porous titania supports were synthesized using this methodology (manuscript to be submitted).

Video Image Stabilization and Registration

NASA Technical Reports Server (NTRS)

Hathaway, David H. (Inventor); Meyer, Paul J. (Inventor)

2002-01-01

A method of stabilizing and registering a video image in multiple video fields of a video sequence provides accurate determination of the image change in magnification, rotation and translation between video fields, so that the video fields may be accurately corrected for these changes in the image in the video sequence. In a described embodiment, a key area of a key video field is selected which contains an image which it is desired to stabilize in a video sequence. The key area is subdivided into nested pixel blocks and the translation of each of the pixel blocks from the key video field to a new video field is determined as a precursor to determining change in magnification, rotation and translation of the image from the key video field to the new video field.

Video Image Stabilization and Registration

NASA Technical Reports Server (NTRS)

Hathaway, David H. (Inventor); Meyer, Paul J. (Inventor)

2003-01-01

A method of stabilizing and registering a video image in multiple video fields of a video sequence provides accurate determination of the image change in magnification, rotation and translation between video fields, so that the video fields may be accurately corrected for these changes in the image in the video sequence. In a described embodiment, a key area of a key video field is selected which contains an image which it is desired to stabilize in a video sequence. The key area is subdivided into nested pixel blocks and the translation of each of the pixel blocks from the key video field to a new video field is determined as a precursor to determining change in magnification, rotation and translation of the image from the key video field to the new video field.

Analysis of turbulence characteristics over the northern Tibetan Plateau area

NASA Astrophysics Data System (ADS)

Li, M. S.; Ma, Y. M.; Ma, W. Q.; Hu, Z. Y.; Ishikawa, H.; Su, Z. B.; Sun, G. L.

2006-07-01

Based on CATOP/Tibet [Coordinated Enhanced Observing Period (CEOP) Asia-Australia Monsoon Project (CA-IMP) on the Tibetan Plateau) turbulent data collected at the Bujiao (BJ) site of the Nagqu area, the turbulent structure and transportation characteristics in the near surface layer during summer are analyzed. The main results show that the relationship between the normalized standard deviation of 3D wind speed and stability satisfies the similarity law tinder both unstable and stable stratifications. The relations of normalized standard deviation of temperature and specific humidity to stability only obey the "-1/3 power law." tinder unstable conditions. In the case of stable stratifications, their relations to stability are dispersing. The sensible heat dominates in the dry period, while in the wet period, the latent heat is larger than the sensible heat.

Statistical evaluation for stability studies under stress storage conditions.

PubMed

Gil-Alegre, M E; Bernabeu, J A; Camacho, M A; Torres-Suarez, A I

2001-11-01

During the pharmaceutical development of a new drug, it is necessary to select as soon as possible the formulation with the best stability characteristics. The current International Commission for Harmonisation (ICH) regulations regarding stability testing requirements for a Registration Application provide the stress testing conditions with the aim of assessing the effect of severe conditions on the drug product. In practice, the well-known Arrhenius theory is still used to make a rapid stability prediction, to estimate a drug product shelf life during early stages of its pharmaceutical development. In this work, both the planning of a stress stability study to obtain a correct stability prediction from a temperature extrapolation and the suitable data treatment to discern the reliability of the stability results are discussed. The study was focused on the early formulation step of a very stable drug, Mitonafide (antineoplastic agent), formulated in a parenteral solution and in tablets. It was observed, for the solid system, that the extrapolated results using Arrhenius theory might be statistically good, but far from the real situation if the stability study is not designed in a correct way. The statistical data treatment and the stress-stability test proposed in this work are suitable to make a reliable stability prediction of different formulations with the same drug, within its pharmaceutical development.

Global growth and stability of agricultural yield decrease with pollinator dependence

PubMed Central

Garibaldi, Lucas A.; Aizen, Marcelo A.; Klein, Alexandra M.; Cunningham, Saul A.; Harder, Lawrence D.

2011-01-01

Human welfare depends on the amount and stability of agricultural production, as determined by crop yield and cultivated area. Yield increases asymptotically with the resources provided by farmers’ inputs and environmentally sensitive ecosystem services. Declining yield growth with increased inputs prompts conversion of more land to cultivation, but at the risk of eroding ecosystem services. To explore the interdependence of agricultural production and its stability on ecosystem services, we present and test a general graphical model, based on Jensen's inequality, of yield–resource relations and consider implications for land conversion. For the case of animal pollination as a resource influencing crop yield, this model predicts that incomplete and variable pollen delivery reduces yield mean and stability (inverse of variability) more for crops with greater dependence on pollinators. Data collected by the Food and Agriculture Organization of the United Nations during 1961–2008 support these predictions. Specifically, crops with greater pollinator dependence had lower mean and stability in relative yield and yield growth, despite global yield increases for most crops. Lower yield growth was compensated by increased land cultivation to enhance production of pollinator-dependent crops. Area stability also decreased with pollinator dependence, as it correlated positively with yield stability among crops. These results reveal that pollen limitation hinders yield growth of pollinator-dependent crops, decreasing temporal stability of global agricultural production, while promoting compensatory land conversion to agriculture. Although we examined crop pollination, our model applies to other ecosystem services for which the benefits to human welfare decelerate as the maximum is approached. PMID:21422295

External nasal dilators: definition, background, and current uses

PubMed Central

Dinardi, Ricardo Reis; de Andrade, Cláudia Ribeiro; Ibiapina, Cássio da Cunha

2014-01-01

Our goal was to revise the literature about external nasal dilators (ENDs) as to their definition, history, and current uses. We reviewed journals in the PubMed and MEDLINE databases. The current uses hereby presented and discussed are physical exercise, nasal congestion and sleep, snoring, pregnancy, cancer, and healthy individuals. Numerous studies have shown that ENDs increase the cross-sectional area of the nasal valve, reducing nasal resistance and transnasal inspiratory pressure and stabilizing the lateral nasal vestibule, avoiding its collapse during final inspiration. These effects also facilitate breathing and are beneficial to patients with nasal obstruction. Furthermore, END use is simple, noninvasive, painless, affordable, and bears minimum risk to the user. Most studies have limited sample size and are mainly focused on physical exercise. In conclusion, ENDs seem useful, so further studies involving potential effects on the performance of physical tests and improvements in sleep quality are necessary, especially in children and teenagers. PMID:25419156

Preparation and properties of biodegradable films from Sterculia urens short fiber/cellulose green composites.

PubMed

Jayaramudu, J; Reddy, G Siva Mohan; Varaprasad, K; Sadiku, E R; Sinha Ray, S; Varada Rajulu, A

2013-04-02

The development of commercially viable "green products", based on natural resources for the matrices and reinforcements, in a wide range of applications, is on the rise. The present paper focuses on Sterculia urens short fiber reinforced pure cellulose matrix composite films. The morphologies of the untreated and 5% NaOH (alkali) treated S. urens fibers were observed by SEM. The effect of 5% NaOH treated S. urens fiber (5, 10, 15 and 20% loading) on the mechanical properties and thermal stability of the composites films is discussed. This paper presents the developments made in the area of biodegradable S. urens short fiber/cellulose (SUSF/cellulose) composite films, buried in the soil and later investigated by the (POM), before and after biodegradation has taken place. SUSF/cellulose composite films have great potential in food packaging and for medical applications. Copyright © 2013 Elsevier Ltd. All rights reserved.

Post isolation modification of exosomes for nanomedicine applications.

PubMed

Hood, Joshua L

2016-07-01

Exosomes are extracellular nanovesicles. They innately possess ideal structural and biocompatible nanocarrier properties. Exosome components can be engineered at the cellular level. Alternatively, when exosome source cells are unavailable for customized exosome production, exosomes derived from a variety of biological origins can be modified post isolation which is the focus of this article. Modification of exosome surface structures allows for exosome imaging and tracking in vivo. Exosome membranes can be loaded with hydrophobic therapeutics to increase drug stability and efficacy. Hydrophilic therapeutics such as RNA can be encapsulated in exosomes to improve cellular delivery. Despite advances in post isolation exosome modification strategies, many challenges to effectively harnessing their therapeutic potential remain. Future topics of exploration include: matching exosome subtypes with nanomedicine applications, optimizing exosomal nanocarrier formulation and investigating how modified exosomes interface with the immune system. Research into these areas will greatly facilitate personalized exosome-based nanomedicine endeavors.

Post isolation modification of exosomes for nanomedicine applications

PubMed Central

Hood, Joshua L

2016-01-01

Exosomes are extracellular nanovesicles. They innately possess ideal structural and biocompatible nanocarrier properties. Exosome components can be engineered at the cellular level. Alternatively, when exosome source cells are unavailable for customized exosome production, exosomes derived from a variety of biological origins can be modified post isolation which is the focus of this article. Modification of exosome surface structures allows for exosome imaging and tracking in vivo. Exosome membranes can be loaded with hydrophobic therapeutics to increase drug stability and efficacy. Hydrophilic therapeutics such as RNA can be encapsulated in exosomes to improve cellular delivery. Despite advances in post isolation exosome modification strategies, many challenges to effectively harnessing their therapeutic potential remain. Future topics of exploration include: matching exosome subtypes with nanomedicine applications, optimizing exosomal nanocarrier formulation and investigating how modified exosomes interface with the immune system. Research into these areas will greatly facilitate personalized exosome-based nanomedicine endeavors. PMID:27348448

Effect of production phase on bottle-fermented sparkling wine quality.

PubMed

Kemp, Belinda; Alexandre, Hervé; Robillard, Bertrand; Marchal, Richard

2015-01-14

This review analyzes bottle-fermented sparkling wine research at each stage of production by evaluating existing knowledge to identify areas that require future investigation. With the growing importance of enological investigation being focused on the needs of the wine production industry, this review examines current research at each stage of bottle-fermented sparkling wine production. Production phases analyzed in this review include pressing, juice adjustments, malolactic fermentation (MLF), stabilization, clarification, tirage, lees aging, disgorging, and dosage. The aim of this review is to identify enological factors that affect bottle-fermented sparkling wine quality, predominantly aroma, flavor, and foaming quality. Future research topics identified include regional specific varieties, plant-based products from vines, grapes, and yeast that can be used in sparkling wine production, gushing at disgorging, and methods to increase the rate of yeast autolysis. An internationally accepted sensory analysis method specifically designed for sparkling wine is required.

Recent Advances in Porous Carbon Materials for Electrochemical Energy Storage.

PubMed

Wang, Libin; Hu, Xianluo

2018-06-18

Climate change and the energy crisis have promoted the rapid development of electrochemical energy-storage devices. Owing to many intriguing physicochemical properties, such as excellent chemical stability, high electronic conductivity, and a large specific surface area, porous carbon materials have always been considering as a promising candidate for electrochemical energy storage. To date, a wide variety of porous carbon materials based upon molecular design, pore control, and compositional tailoring have been proposed for energy-storage applications. This focus review summarizes recent advances in the synthesis of various porous carbon materials from the view of energy storage, particularly in the past three years. Their applications in representative electrochemical energy-storage devices, such as lithium-ion batteries, supercapacitors, and lithium-ion hybrid capacitors, are discussed in this review, with a look forward to offer some inspiration and guidelines for the exploitation of advanced carbon-based energy-storage materials. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Mesoporous Silica Molecular Sieve based Nanocarriers: Transpiring Drug Dissolution Research.

PubMed

Pattnaik, Satyanarayan; Pathak, Kamla

2017-01-01

Improvement of oral bioavailability through enhancement of dissolution for poorly soluble drugs has been a very promising approach. Recently, mesoporous silica based molecular sieves have demonstrated excellent properties to enhance the dissolution velocity of poorly water-soluble drugs. Current research in this area is focused on investigating the factors influencing the drug release from these carriers, the kinetics of drug release and manufacturing approaches to scale-up production for commercial manufacture. This comprehensive review provides an overview of different methods adopted for synthesis of mesoporous materials, influence of processing factors on properties of these materials and drug loading methods. The drug release kinetics from mesoporous silica systems, the manufacturability and stability of these formulations are reviewed. Finally, the safety and biocompatibility issues related to these silica based materials are discussed. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Nanoparticle monolayers under stress: mechanically forced desorption from a fluid-fluid interface

NASA Astrophysics Data System (ADS)

Garbin, Valeria; Crocker, John C.; Stebe, Kathleen J.

2011-11-01

Nanoparticle-laden interfaces are studied for applications to materials with tunable electronic and optical properties, as emulsion stabilizers, and in catalysis. The mechanical response of nanoparticle monolayers under applied stress is of emerging interest since it impacts the success of these applications. Here we focus on the response of nanoparticle-laden interfaces to compression. A monolayer of nanoparticles is allowed to spontaneously form by adsorption from an aqueous suspension onto a pendant drop of oil. The effective surface pressure Π of the composite interface is monitored by pendant drop tensiometry. As the drop is compressed, the nanoparticles are mechanically forced out of the interface into the aqueous phase. A new optical method is developed to measure the nanoparticle area density in situ. We show that desorption occurs at a coverage that corresponds to close packing of the ligand-capped particles, suggesting that ligand-induced repulsion plays a crucial role in the desorption process.

Proposed Cavity for Reduced Slip-Stacking Loss

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eldred, J.; Zwaska, R.

This paper employs a novel dynamical mechanism to improve the performance of slip-stacking. Slip-stacking in an accumulation technique used at Fermilab since 2004 which nearly double the proton intensity. During slip-stacking, the Recycler or the Main Injector stores two particles beams that spatially overlap but have different momenta. The two particle beams are longitudinally focused by two 53 MHz 100 kV RF cavities with a small frequency difference between them. We propose an additional 106 MHz 20 kV RF cavity, with a frequency at the double the average of the upper and lower main RF frequencies. In simulation, we findmore » the proposed RF cavity significantly enhances the stable bucket area and reduces slip-stacking losses under reasonable injection scenarios. We quantify and map the stability of the parameter space for any accelerator implementing slip-stacking with the addition of a harmonic RF cavity.« less

Graphene-Based Photocatalysts for CO2 Reduction to Solar Fuel.

PubMed

Low, Jingxiang; Yu, Jiaguo; Ho, Wingkei

2015-11-05

Recently, photocatalytic CO2 reduction for solar fuel production has attracted much attention because of its potential for simultaneously solving energy and global warming problems. Many studies have been conducted to prepare novel and efficient photocatalysts for CO2 reduction. Graphene, a two-dimensional material, has been increasingly used in photocatalytic CO2 reduction. In theory, graphene shows several remarkable properties, including excellent electronic conductivity, good optical transmittance, large specific surface area, and superior chemical stability. Attributing to these advantages, fabrication of graphene-based materials has been known as one of the most feasible strategies to improve the CO2 reduction performance of photocatalysts. This Perspective mainly focuses on the recent important advances in the fabrication and application of graphene-based photocatalysts for CO2 reduction to solar fuels. The existing challenges and difficulties of graphene-based photocatalysts are also discussed for future application.

Fabrication technologies and sensing applications of graphene-based composite films: Advances and challenges.

PubMed

Yu, Xiaoqing; Zhang, Wensi; Zhang, Panpan; Su, Zhiqiang

2017-03-15

Graphene (G)-based composite materials have been widely explored for the sensing applications ascribing to their atom-thick two-dimensional conjugated structures, high conductivity, large specific surface areas and controlled modification. With the enormous advantages of film structure, G-based composite films (GCFs), prepared by combining G with different functional nanomaterials (noble metals, metal compounds, carbon materials, polymer materials, etc.), show unique optical, mechanical, electrical, chemical, and catalytic properties. Therefore, great quantities of sensors with high sensitivity, selectivity, and stability have been created in recent years. In this review, we focus on the recent advances in the fabrication technologies of GCFs and their specific sensing applications. In addition, the relationship between the properties of GCFs and sensing performance is concentrated on. Finally, the personal perspectives and key challenges of GCFs are mentioned in the hope to shed a light on their potential future research directions. Copyright © 2016 Elsevier B.V. All rights reserved.

Alkyl Pyrocarbonate Electrolyte Additives for Performance Enhancement of Li Ion Cells

NASA Technical Reports Server (NTRS)

Smart, M. C.; Ratnakumar, B. V.; Surampudi, S.

2000-01-01

Lithium ion rechargeable batteries are being developed for various aerospace applications under a NASA-DoD Interagency program. These applications require further improvements in several areas, specifically in the cycle life for LEO and GEO satellites and in the low temperature performance for the Mars Lander and Rover missions. Accordingly, we have been pursuing research studies to achieve improvement in the low temperature performance, long cycle life and active life of Li ion cells. The studies are mainly focused on electrolytes, to identify newer formulations of new electrolyte additives to enhance Li permeability (at low temperatures) and stability towards the electrode. The latter approach is particularly aimed at the formation suitable SEI (solid electrolyte interphase) on carbon electrodes. In this paper, we report the beneficial effect of using alkyl pyrocarbonates as electrolyte additives to improve the low temperature performance of Li ion cells.

Causes of learning disability and epilepsy: a review.

PubMed

Prince, Elizabeth; Ring, Howard

2011-04-01

Although the association between learning disability and epilepsy is well known, until relatively recently specific processes underlying this association were relatively poorly understood. However, scientific advances in molecular biology are starting to guide researchers towards descriptions of genetic and pathophysiological processes that may explain why syndromes of epilepsy and learning disability often co-exist. This article will focus largely on three areas of advancing knowledge: insights gained from wider use of genome-wide array comparative genomic hybridization (aCGH), specific insights gained from detailed study of Rett syndrome and the role of abnormalities of astrocytic function in predisposing to both epilepsy and learning disability. The enormous complexity of the biological underpinnings of the co-occurrence of epilepsy and learning disability are becoming apparent. In the future it is likely that research into therapeutic approaches will include, amongst other approaches, investigations of gene structure and expression, the role of astrocytes and the stability of dendritic spines.

Root Resorption with Orthodontic Mechanics: Pertinent Areas Revisited.

PubMed

Krishnan, V

2017-03-01

Root resorption can occur at any time during orthodontic treatment and lead to a compromise in the prognosis of the tooth and the stability of the treatment results. Recent research has focused more on the cause and effect relationship as well as preventive or treatment options to combat this unwelcome event. Investigations have highlighted the genetic as well as molecular aspects of the process and enabled clinicians to determine which patients might be susceptible. A proper medical history, an assessment of predisposing factors, a radiographic evaluation for alterations in root morphology and careful planning and execution of orthodontic mechanics may reduce the incidence of root resorption. The current review is aimed at providing clinicians and academics with an insight into the process of root resorption, the methods of identification during its early stages and intervention at the right time to reduce its severity. © 2017 Australian Dental Association.

Visualizing In Situ Microstructure Dependent Crack Tip Stress Distribution in IN-617 Using Nano-mechanical Raman Spectroscopy

NASA Astrophysics Data System (ADS)

Zhang, Yang; Mohanty, Debapriya P.; Tomar, Vikas

2016-11-01

Inconel 617 (IN-617) is a solid solution alloy, which is widely used in applications that require high-temperature component operation due to its high-temperature stability and strength as well as strong resistance to oxidation and carburization. The current work focuses on in situ measurements of stress distribution under 3-point bending at elevated temperature in IN-617. A nanomechanical Raman spectroscopy measurement platform was designed and built based on a combination of a customized open Raman spectroscopy (NMRS) system incorporating a motorized scanning and imaging system with a nanomechanical loading platform. Based on the scanning of the crack tip notch area using the NMRS notch tip, stress distribution under applied load with micron-scale resolution for analyzed microstructures is predicted. A finite element method-based formulation to predict crack tip stresses is presented and validated using the presented experimental data.

Numerical modelling on stabilizing large magnetic island by RF current for disruption avoidance

NASA Astrophysics Data System (ADS)

Wang, Xiaojing; Yu, Qingquan; Zhang, Xiaodong; Zhu, Sizheng; Wang, Xiaoguang; Wu, Bin

2018-01-01

Numerical modelling on tearing mode stabilization by RF current due to electron cyclotron current drive (ECCD) has been carried out for the purposes of disruption avoidance, focusing on stabilizing the magnetic island which can grow to a large width and therefore, might cause plasma disruption. When the island has become large, a threshold in driven current for fully stabilizing the mode is found; below this threshold, the island width only slightly decreases. The island’s O-point shifts radially towards the magnetic axis as the mode grows, as a result, applying ECCD at the minor radius of the island’s O-point has a stronger effect than that at the original equilibrium rational surface for stabilizing a large island. During the island growth, the required driven current for mode stabilization increases with the island’s width, indicating that it is more effective to apply ECCD as early as possible for disruption avoidance, as observed in experiments. The numerical results have been compared with those obtained from the modified Rutherford equation.

Asynchrony among local communities stabilises ecosystem function of metacommunities.

PubMed

Wilcox, Kevin R; Tredennick, Andrew T; Koerner, Sally E; Grman, Emily; Hallett, Lauren M; Avolio, Meghan L; La Pierre, Kimberly J; Houseman, Gregory R; Isbell, Forest; Johnson, David Samuel; Alatalo, Juha M; Baldwin, Andrew H; Bork, Edward W; Boughton, Elizabeth H; Bowman, William D; Britton, Andrea J; Cahill, James F; Collins, Scott L; Du, Guozhen; Eskelinen, Anu; Gough, Laura; Jentsch, Anke; Kern, Christel; Klanderud, Kari; Knapp, Alan K; Kreyling, Juergen; Luo, Yiqi; McLaren, Jennie R; Megonigal, Patrick; Onipchenko, Vladimir; Prevéy, Janet; Price, Jodi N; Robinson, Clare H; Sala, Osvaldo E; Smith, Melinda D; Soudzilovskaia, Nadejda A; Souza, Lara; Tilman, David; White, Shannon R; Xu, Zhuwen; Yahdjian, Laura; Yu, Qiang; Zhang, Pengfei; Zhang, Yunhai

2017-12-01

Temporal stability of ecosystem functioning increases the predictability and reliability of ecosystem services, and understanding the drivers of stability across spatial scales is important for land management and policy decisions. We used species-level abundance data from 62 plant communities across five continents to assess mechanisms of temporal stability across spatial scales. We assessed how asynchrony (i.e. different units responding dissimilarly through time) of species and local communities stabilised metacommunity ecosystem function. Asynchrony of species increased stability of local communities, and asynchrony among local communities enhanced metacommunity stability by a wide range of magnitudes (1-315%); this range was positively correlated with the size of the metacommunity. Additionally, asynchronous responses among local communities were linked with species' populations fluctuating asynchronously across space, perhaps stemming from physical and/or competitive differences among local communities. Accordingly, we suggest spatial heterogeneity should be a major focus for maintaining the stability of ecosystem services at larger spatial scales. © 2017 The Authors. Ecology Letters published by CNRS and John Wiley & Sons Ltd.

Uganda: Perfection of Post-Conflict Stability or Ticking Time Bomb

DTIC Science & Technology

2016-01-01

1 UGANDA: PERFECTION OF POST-CONFLICT STABILITY OR TICKING TIME BOMB ? By Kristin M. Pearson and Alex S. Pedersen, United States Air...Force Academy 2015 INSS RESEARCH PAPER 2016 2 UGANDA: PERFECTION OF POST-CONFLICT STABILITY OR TICKING TIME BOMB ? By Kristin M. Pearson and Alex...likely. “The area is a ticking time bomb without ongoing efforts. There’s an entire group of young men trained in military tactics that have said

ASEAN Combined Forces Command

DTIC Science & Technology

1992-04-03

10. SOURCE OF FUNDING NUMBERS PROGRAM PROJECT TASK WORK UNIT ELEMENT NO. NO. NO. ACCESSION NO. 11. TITLE (Include Security Classification) ASEAN...region is a consequence of the stability, coordination and team work of ASEAN. With a reduction of U.S. forces presence in the area, the key to securing...fastest-growing regions in the world today. The stability in the region is a consequence of the stability, coordination and team work of ASEAN. With a

Integrating a Motion Base into a CAVE Automatic Virtual Environment: Phase 1

DTIC Science & Technology

2001-07-01

this, a CAVE system must perform well in the following motion-related areas: visual gaze stability, simulator sickness, realism (or face validity...and performance validity. Visual Gaze Stability Visual gaze stability, the ability to maintain eye fixation on a particular target, depends upon human...reflexes such as the vestibulo-ocular reflex (VOR) and the optokinetic nystagmus (OKN). VOR is a reflex that counter-rotates the eye relative to the

Knee joint stabilization therapy in patients with osteoarthritis of the knee: a randomized, controlled trial.

PubMed

Knoop, J; Dekker, J; van der Leeden, M; van der Esch, M; Thorstensson, C A; Gerritsen, M; Voorneman, R E; Peter, W F; de Rooij, M; Romviel, S; Lems, W F; Roorda, L D; Steultjens, M P M

2013-08-01

To investigate whether an exercise program, initially focusing on knee stabilization and subsequently on muscle strength and performance of daily activities is more effective than an exercise program focusing on muscle strength and performance of daily activities only, in reducing activity limitations in patients with knee osteoarthritis (OA) and instability of the knee joint. A single-blind, randomized, controlled trial involving 159 knee OA patients with self-reported and/or biomechanically assessed knee instability, randomly assigned to two treatment groups. Both groups received a supervised exercise program for 12 weeks, consisting of muscle strengthening exercises and training of daily activities, but only in the experimental group specific knee joint stabilization training was provided. Outcome measures included activity limitations (Western Ontario and McMaster Universities Osteoarthritis Index - WOMAC physical function, primary outcome), pain, global perceived effect and knee stability. Both treatment groups demonstrated large (∼20-40%) and clinically relevant reductions in activity limitations, pain and knee instability, which were sustained 6 months post-treatment. No differences in effectiveness between experimental and control treatment were found on WOMAC physical function (B (95% confidence interval - CI) = -0.01 (-2.58 to 2.57)) or secondary outcome measures, except for a higher global perceived effect in the experimental group (P = 0.04). Both exercise programs were highly effective in reducing activity limitations and pain and restoring knee stability in knee OA patients with instability of the knee. In knee OA patients suffering from knee instability, specific knee joint stabilization training, in addition to muscle strengthening and functional exercises, does not seem to have any additional value. Dutch Trial Register (NTR) registration number: NTR1475. Copyright © 2013 Osteoarthritis Research Society International. Published by Elsevier Ltd. All rights reserved.

The rapid suicide protection of mood stabilizers on patients with bipolar disorder: A nationwide observational cohort study in Taiwan.

PubMed

Tsai, Chia-Jui; Cheng, Chin; Chou, Po-Han; Lin, Ching-Heng; McInnis, Melvin G; Chang, Chia-Li; Lan, Tsuo-Hung

2016-05-15

The suicide rate is high among bipolar disorder (BD) patients. Previous studies have focused on the anti-suicidal effect of long-term treatment with mood stabilizers but less on the immediate preventive effects of interventions. The aim of the study was to evaluate the short-term and immediate anti-suicidal effects of mood stabilizers on recent-onset BD patients. The National Health Insurance Database (NHID) of Taiwan was used to perform a nationwide cohort observation study of suicide behaviors in bipolar disorder. All the recent-onset BD patients (ICD-9-CM code 296 except 296.2 and 296.3) diagnosed between 2000-2005 were collected (n=5091) and followed through 2009. The primary endpoint was the presence of a suicide code or the end of observation; exposure to mood stabilizers in the final month of observation was the independent variable. The hazard ratios (HRs) of suicide-related events, completed suicide, and all-cause mortality were significantly lower for those treated with lithium, divalproex, or carbamazepine compared with no use in the last month (HRs of suicide-related events were 0.10, 0.14 and 0.10, respectively, and all-cause mortality HRs were 0.03; P<0.0001); there was no significant difference in HR between the mood stabilizers. The NIHD does not provide information on the severity, mood status, or treatment adherence of BD patients. Neither substance-related disorder nor personality disorder were included in the analysis. We focused on the effect of the final prescription time period, not the long-term protective effect. The immediate recent use of any mood stabilizer significantly lowers the rate of death, suicide, or suicidal behavior in BD. Copyright © 2016 Elsevier B.V. All rights reserved.

Analytic study of the conditions required for longitudinal stability of dual-wing aircraft

DOE PAGES

Andrews, Stephen Arthur; Perez, Ruben E.

2017-05-11

Recent studies of new, fuel-efficient transport aircraft have considered designs, which make use of two principal lifting surfaces to provide the required lift as well as trim and static stability. Such designs include open tandem-wings as well as closed joined and box-wings. As a group, these aircraft can be termed dual-wing designs. Our study developed a new analytic model, which takes into account the downwash from the two main wings and is sensitive to three important design variables: the relative areas of each wing, the streamwise separation of the wings, and the center of gravity position. This model was usedmore » to better understand trends in the dual-wing geometry on the stability, maneuverability, and lift-to-drag ratio of the aircraft. Dual-wing aircraft have been shown to have reduced the induced drag compared to the conventional designs. In addition, further drag reductions can be realized as the horizontal tail can be removed if the dual-wings have sufficient streamwise stagger to provide the moments necessary for trim and longitudinal stability. As both wings in a dual-wing system carry a significant fraction of the total lift, trends in such designs that led to longitudinal stability can differ from those of the conventional aircraft and have not been the subject of detailed investigation. Results from the analytic model showed that the longitudinal stability required either a reduction of the fore wing area or shifting the center of gravity forward from the midpoint of both wings' aerodynamic centers. Additionally, for wing configurations of approximately equal fore and aft wing areas, increasing the separation between the two wings decreased the stability of the aircraft. The source of this unusual behavior was the asymmetric distribution of downwash upstream and downstream of the wing. These relationships between dual-wing geometry and stability will provide initial guidance on the conceptual design of dual-wing aircraft and aid in the understanding of the results of more complex studies of such designs, furthering the development of future transport aircraft.« less

Degradation and stabilization of ice wedges: Implications for assessing risk of thermokarst in northern Alaska

NASA Astrophysics Data System (ADS)

Kanevskiy, Mikhail; Shur, Yuri; Jorgenson, Torre; Brown, Dana R. N.; Moskalenko, Nataliya; Brown, Jerry; Walker, Donald A.; Raynolds, Martha K.; Buchhorn, Marcel

2017-11-01

Widespread degradation of ice wedges has been observed during the last decades in numerous areas within the continuous permafrost zone of Eurasia and North America. To study ice-wedge degradation, we performed field investigations at Prudhoe Bay and Barrow in northern Alaska during 2011-2016. In each study area, a 250-m transect was established with plots representing different stages of ice-wedge degradation/stabilization. Field work included surveying ground- and water-surface elevations, thaw-depth measurements, permafrost coring, vegetation sampling, and ground-based LiDAR scanning. We described cryostratigraphy of frozen soils and stable isotope composition, analyzed environmental characteristics associated with ice-wedge degradation and stabilization, evaluated the vulnerability and resilience of ice wedges to climate change and disturbances, and developed new conceptual models of ice-wedge dynamics that identify the main factors affecting ice-wedge degradation and stabilization and the main stages of this quasi-cyclic process. We found significant differences in the patterns of ice-wedge degradation and stabilization between the two areas, and the patterns were more complex than those previously described because of the interactions of changing topography, water redistribution, and vegetation/soil responses that can interrupt or reinforce degradation. Degradation of ice wedges is usually triggered by an increase in the active-layer thickness during exceptionally warm and wet summers or as a result of flooding or disturbance. Vulnerability of ice wedges to thermokarst is controlled by the thickness of the intermediate layer of the upper permafrost, which overlies ice wedges and protects them from thawing. In the continuous permafrost zone, degradation of ice wedges rarely leads to their complete melting; and in most cases wedges eventually stabilize and can then resume growing, indicating a somewhat cyclic and reversible process. Stabilization of ice wedges after their partial degradation makes them better protected than before degradation because the intermediate layer is usually 2 to 3 times thicker on top of stabilized ice wedges than on top of initial ice wedges in undisturbed conditions. As a result, the likelihood of formation of large thaw lakes in the continuous permafrost zone triggered by ice-wedge degradation alone is very low.

Analytic study of the conditions required for longitudinal stability of dual-wing aircraft

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andrews, Stephen Arthur; Perez, Ruben E.

Recent studies of new, fuel-efficient transport aircraft have considered designs, which make use of two principal lifting surfaces to provide the required lift as well as trim and static stability. Such designs include open tandem-wings as well as closed joined and box-wings. As a group, these aircraft can be termed dual-wing designs. Our study developed a new analytic model, which takes into account the downwash from the two main wings and is sensitive to three important design variables: the relative areas of each wing, the streamwise separation of the wings, and the center of gravity position. This model was usedmore » to better understand trends in the dual-wing geometry on the stability, maneuverability, and lift-to-drag ratio of the aircraft. Dual-wing aircraft have been shown to have reduced the induced drag compared to the conventional designs. In addition, further drag reductions can be realized as the horizontal tail can be removed if the dual-wings have sufficient streamwise stagger to provide the moments necessary for trim and longitudinal stability. As both wings in a dual-wing system carry a significant fraction of the total lift, trends in such designs that led to longitudinal stability can differ from those of the conventional aircraft and have not been the subject of detailed investigation. Results from the analytic model showed that the longitudinal stability required either a reduction of the fore wing area or shifting the center of gravity forward from the midpoint of both wings' aerodynamic centers. Additionally, for wing configurations of approximately equal fore and aft wing areas, increasing the separation between the two wings decreased the stability of the aircraft. The source of this unusual behavior was the asymmetric distribution of downwash upstream and downstream of the wing. These relationships between dual-wing geometry and stability will provide initial guidance on the conceptual design of dual-wing aircraft and aid in the understanding of the results of more complex studies of such designs, furthering the development of future transport aircraft.« less

Solution techniques for transient stability-constrained optimal power flow – Part II

DOE PAGES

Geng, Guangchao; Abhyankar, Shrirang; Wang, Xiaoyu; ...

2017-06-28

Transient stability-constrained optimal power flow is an important emerging problem with power systems pushed to the limits for economic benefits, dense and larger interconnected systems, and reduced inertia due to expected proliferation of renewable energy resources. In this study, two more approaches: single machine equivalent and computational intelligence are presented. Also discussed are various application areas, and future directions in this research area. In conclusion, a comprehensive resource for the available literature, publicly available test systems, and relevant numerical libraries is also provided.

Solution techniques for transient stability-constrained optimal power flow – Part II

DOE Office of Scientific and Technical Information (OSTI.GOV)

Geng, Guangchao; Abhyankar, Shrirang; Wang, Xiaoyu

Transient stability-constrained optimal power flow is an important emerging problem with power systems pushed to the limits for economic benefits, dense and larger interconnected systems, and reduced inertia due to expected proliferation of renewable energy resources. In this study, two more approaches: single machine equivalent and computational intelligence are presented. Also discussed are various application areas, and future directions in this research area. In conclusion, a comprehensive resource for the available literature, publicly available test systems, and relevant numerical libraries is also provided.

Environmental problems in the coastal and wetlands ecosystems of Virginia Beach, Virginia

USGS Publications Warehouse

Buzzanell, Peter J.; McGinty, Herbert K.

1975-01-01

Many of the city of Virginia Beach's beach stabilization and sewage disposal problems are the result of an inadequate understanding of the physical and biological systems. Influenced by population and economic pressures, natural systems were artificially stabilized by engineering projects that had to be constantly maintained. These same pressures continue to prevail today in spite of a new environmental awareness; changes are occurring very slowly. Furthermore, the lack of adequate sewage disposal facilities and the continued urbanization of inappropriate areas are threatening Virginia Beach's attractiveness as a resort area.

Stabilizing human regulatory T cells for tolerance inducing immunotherapy.

PubMed

He, Xuehui; Koenen, Hans Jpm; Slaats, Jeroen Hr; Joosten, Irma

2017-08-01

Many autoimmune diseases develop as a consequence of an altered balance between autoreactive immune cells and suppressive FOXP3 + Treg. Restoring this balance through amplification of Treg represents a promising strategy to treat disease. However, FOXP3 + Treg might become unstable especially under certain inflammatory conditions, and might transform into proinflammatory cytokine-producing cells. The issue of heterogeneity and instability of Treg has caused considerable debate in the field and has important implications for Treg-based immunotherapy. In this review, we discuss how Treg stability is defined and what the molecular mechanisms underlying the maintenance of FOXP3 expression and the regulation of Treg stability are. Also, we elaborate on current strategies used to stabilize human Treg for clinical purposes. This review focuses on human Treg, but considering that cell-intrinsic mechanisms to regulate Treg stability in mice and in humans might be similar, data derived from mice studies are also discussed in this paper.

Evaluation of Thermal Stability of Ausferrite in Austempered Ductile Iron Using Differential Scanning Calorimetry

NASA Astrophysics Data System (ADS)

Warsinski, Karl C.

Austempered Ductile Iron (ADI) is prone to changes in microstructure and mechanical properties when exposed to elevated service temperatures. Differential Scanning Calorimetry has been used to evaluate the stabilizing effects of copper, nickel, molybdenum, and cobalt on the ausferrite structure. Previous studies have conflated the effects of various alloy additions, and little effort has been made to systematically catalog the effects of individual elements. The focus of the current research has been to identify alloying elements that more strongly stabilize the ausferrite structure in order to improve service life of ADI at elevated temperatures. Nickel has been shown to have a moderate stabilizing effect, while copper and molybdenum cause a much sharper increase in activation energy. Cobalt has a high stabilizing effect at 0.5% addition by weight, but a further increase to 2.36% results in a slight decrease in activation energy.

2001-2010 glacier changes in the Central Karakoram National Park: a contribution to evaluate the magnitude and rate of the "Karakoram anomaly"

NASA Astrophysics Data System (ADS)

Minora, U.; Bocchiola, D.; D'Agata, C.; Maragno, D.; Mayer, C.; Lambrecht, A.; Mosconi, B.; Vuillermoz, E.; Senese, A.; Compostella, C.; Smiraglia, C.; Diolaiuti, G.

2013-06-01

Karakoram is one of the most glacierized region worldwide, and glaciers therein are the main water resource of Pakistan. The attention paid to this area is increasing, because the evolution of its glaciers recently depicted a situation of general stability, known as "Karakoram Anomaly", in contrast to glacier retreat worldwide. Here we focused our attention upon the glacier evolution within the Central Karakoram National Park (CKNP, a newborn park of this region, ca. 12 162 km2 in area) to assess the magnitude and rate of such anomaly. By means of Remote Sensing data (i.e.: Landsat images), we analyzed a sample of more than 700 glaciers, and we found out their area change between 2001 and 2010 is not significant (+27 km2 ± 42 km2), thus confirming their stationarity. We analyzed climate data, snow coverage from MODIS, and supraglacial debris presence, as well as potential (con-) causes. We found a slight decrease of summer temperatures (down to -1.5 °C during 1980-2009) and an increase of wet days during winter (up +3.3 days yr-1 during 1980-2009), possibly increasing snow cover duration, consistently with MODIS data. We further detected considerable supra-glacial debris coverage (ca. 20% of the glacier area which rose up to 31% considering only the ablation area), which could have reduced buried ice melting during the last decade. These results provide further ground to uphold the existence of the Karakoram Anomaly, and present an useful template for assessment of water availability within the glaciers of the CKNP.

Iran - What Strategic Importance to the Free World?

DTIC Science & Technology

1966-04-08

still derived from three fundamen- tal factors: geographic position, strategic resources, and the political stability . It is within these areas...such a link does exist and is meaningful in our examina- tion into the political stability of present day Iran. There has never been a well defined

18 CFR 270.305 - Determination of tight formation areas.

Code of Federal Regulations, 2010 CFR

2010-04-01

... pressure, of wells completed for production in such portion of such formation, without stimulation, is not...). Such expected stabilized, pre-stimulation production rate is to be determined through an arithmetic mean averaging of the known stabilized, pre-stimulation production rates obtained from the wells that...

Silage review: Recent advances and future uses of silage additives.

PubMed

Muck, R E; Nadeau, E M G; McAllister, T A; Contreras-Govea, F E; Santos, M C; Kung, L

2018-05-01

Additives have been available for enhancing silage preservation for decades. This review covers research studies published since 2000 that have investigated the efficacy of silage additives. The review has been divided into 6 categories of additives: homofermentative lactic acid bacteria (LAB), obligate heterofermentative LAB, combination inoculants containing obligate heterofermentative LAB plus homofermentative LAB, other inoculants, chemicals, and enzymes. The homofermentative LAB rapidly decrease pH and increase lactic acid relative to other fermentation products, although a meta-analysis indicated no reduction in pH in corn, sorghum, and sugarcane silages relative to untreated silages. These additives resulted in higher milk production according to the meta-analysis by mechanisms that are still unclear. Lactobacillus buchneri is the dominant species used in obligate heterofermentative LAB silage additives. It slowly converts lactic acid to acetic acid and 1,2-propanediol during silo storage, improving aerobic stability while having no effect on animal productivity. Current research is focused on finding other species in the Lb. buchneri group capable of producing more rapid improvements in aerobic stability. Combination inoculants aim to provide the aerobic stability benefits of Lb. buchneri with the silage fermentation efficiency and animal productivity benefits of homofermentative LAB. Research indicates that these products are improving aerobic stability, but feeding studies are not yet sufficient to make conclusions about effects on animal performance. Novel non-LAB species have been studied as potential silage inoculants. Streptococcus bovis is a potential starter species within a homofermentative LAB inoculant. Propionibacterium and Bacillus species offer improved aerobic stability in some cases. Some yeast research has focused on inhibiting molds and other detrimental silage microorganisms, whereas other yeast research suggests that it may be possible to apply a direct-fed microbial strain at ensiling, have it survive ensiling, and multiply during feed out. Chemical additives traditionally have fallen in 2 groups. Formic acid causes direct acidification, suppressing clostridia and other undesired bacteria and improving protein preservation during ensiling. On the other hand, sorbic, benzoic, propionic, and acetic acids improve silage aerobic stability at feed out through direct inhibition of yeasts and molds. Current research has focused on various combinations of these chemicals to improve both aerobic stability and animal productivity. Enzyme additives have been added to forage primarily to breakdown plant cell walls at ensiling to improve silage fermentation by providing sugars for the LAB and to enhance the nutritive value of silage by increasing the digestibility of cell walls. Cellulase or hemicellulase mixtures have been more successful at the former than the latter. A new approach focused on Lb. buchneri producing ferulic acid esterase has also had mixed success in improving the efficiency of silage digestion. Another new enzyme approach is the application of proteases to corn silage to improve starch digestibility, but more research is needed to determine the feasibility. Future silage additives are expected to directly inhibit clostridia and other detrimental microorganisms, mitigate high mycotoxin levels on harvested forages during ensiling, enhance aerobic stability, improve cell wall digestibility, increase the efficiency of utilization of silage nitrogen by cattle, and increase the availability of starch to cattle. Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

EPA Region 7 Aquatic Focus Areas (ECO_RES.R7_AQUATIC_FOCUS_AREAS)

EPA Pesticide Factsheets

This shapefile consists of 347 individual Aquatic Ecological System (AES) polygons that are the Aquatic Conservation Focus Areas for EPA Region 7. The focus areas are those areas within each aquatic ecological system types that, if preserved, would maintain the biological and ecological diversity extant within that ecological system type. The layer consists of those polygons from the R7_AES.shp shapefile that had the highest ranks. The AES polygons in the Missouri portion of the file were appended and are those that contain the 158 aquatic conservation opportunity areas identified in Missouri as part of another project (Missouri Department of Conservation Aquatic Biodiversity Assessment 2005). Note that the identifiers in the Missouri portion of this file will not match the ID's in any Missouri specific files.

Mesohaline submerged aquatic vegetation survey along the U.S. gulf of Mexico coast, 2000: A stratified random approach

USGS Publications Warehouse

Carter, J.; Merino, J.H.; Merino, S.L.

2009-01-01

Estimates of submerged aquatic vegetative (SAV) along the U.S. Gulf of Mexico (Gulf) generally focus on seagrasses. In 2000, we attempted a synoptic survey of SAV in the mesohaline (5-20 ppt) zone of estuarine and nearshore areas of the northeastern Gulf. Areas with SAV were identified from existing aerial 1992 photography, and a literature review was used to select those areas that were likely to experience mesohaline conditions during the growing season. In 2000, a drought year, we visited 217 randomly selected SAV beds and collected data on species composition and environmental conditions. In general, sites were either clearly polyhaline (2: 20 ppt) or oligohaline (S 5 ppt), with only five sites measuring between 5 and 20 ppt. Ruppia maritima L. (13-35 ppt, n = 28) was the only species that occurred in mesohaline salinities. Halodule wrightii Asch. occurred in 73% of the beds. The nonindigenous Myriophyllum spicatum L. was present in four locations with salinities below 3 ppt. No nonindigenous macroalgae were identified, and no nonindigenous angiosperms occurred in salinities above 3 ppt. Selecting sample locations based on historical salinity data was not a successful strategy for surveying SAV in mesohaline systems, particularly during a drought year. Our ability to locate SAV beds within 50 m of their aerially located position 8 yr later demonstrates some SAV stability in the highly variable conditions of the study area. ?? 2009 by the Marine Environmental Silences Consortium of Alabama.

Assessment of Geothermal Resource Potential at a High-Priority Area on the Utah Testing and Training Range–South (UTTR–S)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Richard P. Smith, PhD., PG; Robert P. Breckenridge, PhD.; Thomas R. Wood, PhD.

2012-04-01

Field investigations conducted during 2011 support and expand the conclusion of the original Preliminary Report that discovery of a viable geothermal system is possible in the northwestern part of the Utah Testing and Training Range-South (UTTR-S), referred to henceforth as Focus Area 1. The investigations defined the southward extent of the Wendover graben into and near Focus Area 1, enhanced the understanding of subsurface conditions, and focused further geothermal exploration efforts towards the northwestern-most part of Focus Area 1. Specifically, the detailed gravity survey shows that the Wendover graben, first defined by Cook et al. (1964) for areas north ofmore » Interstate Highway 80, extends and deepens southwest-ward to the northwest corner of Focus Area 1. At its deepest point, the intersection with a northwest-trending graben there is favorable for enhanced permeability associated with intersecting faults. Processing and modeling of the gravity data collected during 2011 provide a good understanding of graben depth and distribution of faults bounding the graben and has focused the interest area of the study. Down-hole logging of temperatures in wells made available near the Intrepid, Inc., evaporation ponds, just north of Focus Area 1, provide a good understanding of the variability of thermal gradients in that area and corroborate the more extensive temperature data reported by Turk (1973) for the depth range of 300-500 m. Moderate temperature gradients in the northern part of the Intrepid area increase to much higher gradients and bottom-hole temperatures southeastward, towards graben-bounding faults, suggesting upwelling geothermal waters along those faults. Water sampling, analysis, and temperature measurements of Blue Lakes and Mosquito Willey's springs, on the western boundary of Focus Area 1, also show elevated temperatures along the graben-bounding fault system. In addition, water chemistry suggests origin of those waters in limestone rocks beneath the graben in areas with temperatures as high as 140 C (284 F). In conclusion, all of the field data collected during 2011 and documented in the Appendices of this report indicate that there is reasonable potential for a viable geothermal resource along faults that bound the Wendover graben. Prospects for a system capable of binary electrical generation are especially good, and the possibility of a flash steam system is also within reason. The next steps should focus on securing the necessary funding for detailed geophysical surveys and for drilling a set of temperature gradient wells to further evaluate the resource, and to focus deep exploration efforts in the most promising areas.« less

Analysing the climatic extremes of future projections for the MedCORDEX domain using RCP4.5 and RCP8.5 scenario

NASA Astrophysics Data System (ADS)

Bartholy, Judit; Pongracz, Rita; Pieczka, Ildiko; Szabone Andre, Karolina

2017-04-01

In this study HadGEM2 global climate model outputs were downscaled with RegCM4.3 for the entire MED-44 CORDEX area for the period 1950-2099 using RCP4.5 and RCP8.5 scenario. The 50-km resolution RegCM-outputs served as input for further downscaling using 10 km as a horizontal resolution for a smaller domain covering Central Europe with special focus on the Carpathian Region. RCP4.5 is a stabilization scenario while RCP8.5 is a rising radiative forcing pathway, therefore, the difference in the simulation outputs helps to quantify the inertia of the climate system, the importance of anthropogenic influence on climate, and shows the evidence for the need of mitigation and adaptation measures. Evidently, higher temperature change corresponds to RCP8.5 compared to RCP4.5. The difference of global and/or regional warming between the two scenario can reach (or even exceed) 2 °C from the second part of the century. Differences in precipitation projections are less straightforward to explain as no direct link exists with warming and radiative forcing, however, the annual distribution of precipitation is projected to change, which may lead to important consequences on society. Our analysis compares the estimated temperature and precipitation changes with special focus on extreme climatic conditions for the following 10 subregions of the MED-44 CORDEX area: Iberian Peninsula, Apennine Peninsula, Balkan Region, Asia Minor, East European Plain, Middle European Plain, Carpathian Basin, Carpathian Mountains, Alps, Western Europe.

Balancing Two Cultures: American Indian/Alaska Native Medical Students' Perceptions of Academic Medicine Careers.

PubMed

Sánchez, John Paul; Poll-Hunter, Norma; Stern, Nicole; Garcia, Andrea N; Brewster, Cheryl

2016-08-01

American Indians and Alaska Natives (AI/AN) remain underrepresented in the academic medicine workforce and little is known about cultivating AI/AN medical students' interest in academic medicine careers. Five structured focus groups were conducted including 20 medical students and 18 physicians. The discussion guide explored factors influencing AI/AN trainees' academic medicine career interest and recommended approaches to increase their pursuit of academia. Consensual qualitative research was employed to analyze transcripts. Our research revealed six facilitating factors, nine dissuading factors, and five recommendations towards cultivating AI/AN pursuit of academia. Facilitators included the opportunity to teach, serving as a role model/mentor, enhancing the AI/AN medical education pipeline, opportunities to influence institution, collegiality, and financial stability. Dissuading factors included limited information on academic career paths, politics, lack of credit for teaching and community service, isolation, self-doubt, lower salary, lack of positions in rural areas, lack of focus on clinical care for AI/AN communities, and research obligations. Recommendations included heighten career awareness, recognize the challenges in balancing AI/AN and academic cultures, collaborate with IHS on faculty recruitment strategies, identify concordant role models/mentors, and identify loan forgiveness programs. Similar to other diverse medical students', raising awareness of academic career opportunities especially regarding teaching and community scholarship, access to concordant role models/mentors, and supportive institutional climates can also foster AI/AN medical students' pursuit of academia. Unique strategies for AI/AN trainees include learning how to balance AI/AN and academic cultures, collaborating with IHS on faculty recruitment strategies, and increasing faculty opportunities in rural areas.

Social-ecological predictors of global invasions and extinctions

USGS Publications Warehouse

Lotz, Aaron; Allen, Craig R.

2013-01-01

Most assessments of resilience have been focused on local conditions. Studies focused on the relationship between humanity and environmental degradation are rare, and are rarely comprehensive. We investigated multiple social-ecological factors for 100 countries around the globe in relation to the percentage of invasions and extinctions within each country. These 100 countries contain approximately 87% of the world’s population, produce 43% of the world’s per capita gross domestic product (GDP), and take up 74% of the earth’s total land area. We used an information theoretic approach to determine which models were most supported by our data, utilizing an a priori set of plausible models that included a combination of 15 social-ecological variables, each social-ecological factor by itself, and selected social-ecological factors grouped into three broad classes. These variables were per capita GDP, export-import ratio, tourism, undernourishment, energy efficiency, agricultural intensity, rainfall, water stress, wilderness protection, total biodiversity, life expectancy, adult literacy, pesticide regulation, political stability, and female participation in government. Our results indicate that as total biodiversity and total land area increase, the percentage of endangered birds also increases. As the independent variables (agricultural intensity, rainfall, water stress, and total biodiversity) in the ecological class model increase, the percentage of endangered mammals in a country increases. The percentage of invasive birds and mammals in a country increases as per capita GDP increases. As life expectancy increases, the percentage of invasive and endangered birds and mammals increases. Although our analysis does not determine mechanisms, the patterns observed in this study provide insight into the dynamics of a complex, global, social-ecological system.

An assessment of the mechanical stability of wells offshore Nigeria

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lowrey, J.P.; Ottesen, S.

In 1991 lost time due to stuck pipe related drilling problems accounted for approximately 18% of total drilling time in Mobil Producing Nigeria Ultd.`s (MPN) offshore operations. The primary cause of stuck pipe was identified as mechanical wellbore instability. This paper presents an assessment of the mechanical stability of MPN`s wells offshore Nigeria. The objectives of the study were to: (1) determine the magnitude of the in-situ principal stresses and material properties of the troublesome Intra-Biafra and Qua Iboe shale sequences; (2) quantify the drilling fluid densities required to drill mechanically stable wells through these formations; (3) review and recommendmore » well planning and operational parameters which aid in minimizing wellbore stability-related drilling problems. The well-bore stability assessment was carried out with the aid of a 3-dimensional wellbore stability model using field derived data from the study area to corroborate the results. The collection and analysis of drilling data (borehole geometry and density logs, pore pressure, leak-off tests, local geology and other relevant well records) to determine the magnitude of the in-situ principal stresses, together with compressive strength tests on formation cores are discussed. Minimum safe drilling fluid densities to promote wellbore stability as a function of well geometry and depth are presented for the most troublesome shales drilled in the study area. Implementation of the results reduced wellbore stability related problems and associated trouble time to less than 5% in 1992.« less

A Project to Design and Build the Magnets for a New Test Beamline, the ATF2, at KEK

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spencer, Cherrill M.; /slac; Sugahara, Ryuhei

2011-02-07

In order to achieve the high luminosity required at the proposed International Linear Collider (ILC), it is critical to focus the beams to nanometer size with the ILC Beam Delivery System, and to maintain the beams collisions with a nanometer-scale stability. To establish the technologies associated with this ultra-high precision beam handling, a special beamline has been designed and built as an extension of the existing extraction beamline of the Accelerator Test Facility at KEK, Japan. The ATF provides an adequate ultra-low emittance electron beam that is comparable to the ILC requirements; the ATF2 mimics the ILC final focus systemmore » to create a tightly focused, stable beam. There are 37 magnets in the ATF2, 29 quadrupoles, 5 sextupoles and 3 bends. These magnets had to be acquired in a short time and at minimum cost, which led to various acquisition strategies; but nevertheless they had to meet strict requirements on integrated strength, physical dimensions, compatibility with existing magnet movers and beam position monitors, mechanical stability and field stability and quality. This paper will describe how 2 styles of quadrupoles, 2 styles of sextupoles, one dipole style and their supports were designed, fabricated, refurbished or modified, measured and aligned by a small team of engineers from 3 continents.« less

Interval stability for complex systems

NASA Astrophysics Data System (ADS)

Klinshov, Vladimir V.; Kirillov, Sergey; Kurths, Jürgen; Nekorkin, Vladimir I.

2018-04-01

Stability of dynamical systems against strong perturbations is an important problem of nonlinear dynamics relevant to many applications in various areas. Here, we develop a novel concept of interval stability, referring to the behavior of the perturbed system during a finite time interval. Based on this concept, we suggest new measures of stability, namely interval basin stability (IBS) and interval stability threshold (IST). IBS characterizes the likelihood that the perturbed system returns to the stable regime (attractor) in a given time. IST provides the minimal magnitude of the perturbation capable to disrupt the stable regime for a given interval of time. The suggested measures provide important information about the system susceptibility to external perturbations which may be useful for practical applications. Moreover, from a theoretical viewpoint the interval stability measures are shown to bridge the gap between linear and asymptotic stability. We also suggest numerical algorithms for quantification of the interval stability characteristics and demonstrate their potential for several dynamical systems of various nature, such as power grids and neural networks.

Image motion compensation by area correlation and centroid tracking of solar surface features

NASA Technical Reports Server (NTRS)

Nein, M. E.; Mcintosh, W. R.; Cumings, N. P.

1983-01-01

An experimental solar correlation tracker was tested and evaluated on a ground-based solar magnetograph. Using sunspots as fixed targets, tracking error signals were derived by which the telescope image was stabilized against wind induced perturbations. Two methods of stabilization were investigated; mechanical stabilization of the image by controlled two-axes motion of an active optical element in the telescope beam, and electronic stabilization by biasing of the electron scan in the recording camera. Both approaches have demonstrated telescope stability of about 0.6 arc sec under random perturbations which can cause the unstabilized image to move up to 120 arc sec at frequencies up to 30 Hz.

Improving posture-motor dual-task with a supraposture-focus strategy in young and elderly adults

PubMed Central

Yu, Shu-Han

2017-01-01

In a postural-suprapostural task, appropriate prioritization is necessary to achieve task goals and maintain postural stability. A “posture-first” principle is typically favored by elderly people in order to secure stance stability, but this comes at the cost of reduced suprapostural performance. Using a postural-suprapostural task with a motor suprapostural goal, this study investigated differences between young and older adults in dual-task cost across varying task prioritization paradigms. Eighteen healthy young (mean age: 24.8 ± 5.2 years) and 18 older (mean age: 68.8 ± 3.7 years) adults executed a designated force-matching task from a stabilometer board using either a stabilometer stance (posture-focus strategy) or force-matching (supraposture-focus strategy) as the primary task. The dual-task effect (DTE: % change in dual-task condition; positive value: dual-task benefit, negative value: dual-task cost) of force-matching error and reaction time (RT), posture error, and approximate entropy (ApEn) of stabilometer movement were measured. When using the supraposture-focus strategy, young adults exhibited larger DTE values in each behavioral parameter than when using the posture-focus strategy. The older adults using the supraposture-focus strategy also attained larger DTE values for posture error, stabilometer movement ApEn, and force-matching error than when using the posture-focus strategy. These results suggest that the supraposture-focus strategy exerted an increased dual-task benefit for posture-motor dual-tasking in both healthy young and elderly adults. The present findings imply that the older adults should make use of the supraposture-focus strategy for fall prevention during dual-task execution. PMID:28151943

Improving posture-motor dual-task with a supraposture-focus strategy in young and elderly adults.

PubMed

Yu, Shu-Han; Huang, Cheng-Ya

2017-01-01

In a postural-suprapostural task, appropriate prioritization is necessary to achieve task goals and maintain postural stability. A "posture-first" principle is typically favored by elderly people in order to secure stance stability, but this comes at the cost of reduced suprapostural performance. Using a postural-suprapostural task with a motor suprapostural goal, this study investigated differences between young and older adults in dual-task cost across varying task prioritization paradigms. Eighteen healthy young (mean age: 24.8 ± 5.2 years) and 18 older (mean age: 68.8 ± 3.7 years) adults executed a designated force-matching task from a stabilometer board using either a stabilometer stance (posture-focus strategy) or force-matching (supraposture-focus strategy) as the primary task. The dual-task effect (DTE: % change in dual-task condition; positive value: dual-task benefit, negative value: dual-task cost) of force-matching error and reaction time (RT), posture error, and approximate entropy (ApEn) of stabilometer movement were measured. When using the supraposture-focus strategy, young adults exhibited larger DTE values in each behavioral parameter than when using the posture-focus strategy. The older adults using the supraposture-focus strategy also attained larger DTE values for posture error, stabilometer movement ApEn, and force-matching error than when using the posture-focus strategy. These results suggest that the supraposture-focus strategy exerted an increased dual-task benefit for posture-motor dual-tasking in both healthy young and elderly adults. The present findings imply that the older adults should make use of the supraposture-focus strategy for fall prevention during dual-task execution.

Focusing light through dynamical samples using fast continuous wavefront optimization.

PubMed

Blochet, B; Bourdieu, L; Gigan, S

2017-12-01

We describe a fast continuous optimization wavefront shaping system able to focus light through dynamic scattering media. A micro-electro-mechanical system-based spatial light modulator, a fast photodetector, and field programmable gate array electronics are combined to implement a continuous optimization of a wavefront with a single-mode optimization rate of 4.1 kHz. The system performances are demonstrated by focusing light through colloidal solutions of TiO 2 particles in glycerol with tunable temporal stability.

Transient improvements in fixational stability in strabismic amblyopes following bifoveal fixation and reduced interocular suppression.

PubMed

Raveendran, Rajkumar Nallour; Babu, Raiju J; Hess, Robert F; Bobier, William R

2014-03-01

To test the hypothesis that fixational stability of the amblyopic eye in strabismics will improve when viewing provides both bifoveal fixation and reduced inter-ocular suppression by reducing the contrast to the fellow eye. Seven strabismic amblyopes (Age: 29.2 ± 9 years; five esotropes and two exotropes) showing clinical characteristics of central suppression were recruited. Interocular suppression was measured by a global motion task. For each participant, a balance point was determined which defined contrast levels for each eye where binocular combination was optimal (interocular suppression minimal). When the balance point could not be determined, this participant was excluded. Bifoveal fixation was established by ocular alignment using a haploscope. Participants dichoptically viewed similar targets (a cross of 2.3° surrounded by a square of 11.3°) at 40 cm. Target contrasts presented to each eye were either high contrast (100% to both eyes) or balanced contrast (attenuated contrast in the fellow fixing eye). Fixation stability was measured over a 5 min period and quantified using bivariate contour ellipse areas in four different binocular conditions; unaligned/high contrast, unaligned/balance point, aligned/high contrast and aligned/balance point. Fixation stability was also measured in six control subjects (Age: 25.3 ± 4 years). Bifoveal fixation in the strabismics was transient (58.15 ± 15.7 s). Accordingly, fixational stability was analysed over the first 30 s using repeated measures anova. Post hoc analysis revealed that for the amblyopic subjects, the fixational stability of the amblyopic eye was significantly improved in aligned/high contrast (p = 0.01) and aligned/balance point (p < 0.01) conditions. Fixational stability of the fellow fixing eye was not different statistically across conditions. Bivariate contour ellipse areas of the amblyopic and fellow fixing eyes were therefore averaged for each amblyope in the four conditions and compared with normals. This averaged bivariate contour ellipse area was significantly greater (reduced fixational stability, p = 0.04) in amblyopes compared to controls except in the case of aligned and balanced contrast (aligned/balance point, p = 0.19). Fixation stability in the amblyopic eye appears to improve with bifoveal fixation and reduced interocular suppression. However, once initiated, bifoveal fixation is transient with the strabismic eye drifting away from foveal alignment, thereby increasing the angle of strabismus. © 2014 The Authors Ophthalmic & Physiological Optics © 2014 The College of Optometrists.

Creating a Culture of Innovation: The Challenge in Becoming and Staying a World-Class University

ERIC Educational Resources Information Center

Tierney, William G.

2014-01-01

In the 21st century world-class universities will need to be much more focused on innovation, rather than on stability and standardization. An innovative organization is different from a stable one. It requires different skills from its participants, and it functions in a different way from a stable organization. A focus on innovation will…

Scholastic Adaptation and Socio-Cognitive Abilities of Children between 3 and 7 Years of Age.

ERIC Educational Resources Information Center

Guillain, Andre; Pry, Rene

Building on the assumption that there is cognitive organization to social abilities, two studies analyzed stability and change of this organization in children. The first study focused on children who attended the first year and second year of nursery school, and the first year of elementary school. The second study focused on those children who…

Choices in International Conflict: With a Focus on Security Issues in Asia.

ERIC Educational Resources Information Center

Francis, Gregory; Mukai, Gary; Kim, Pearl; Leininger, James

Many world leaders and scholars feel that the U.S.-Japan Security Alliance is essential for long-term peace, prosperity, and stability in Asia. The purpose of this curriculum unit is to examine this alliance by introducing students to case studies of international conflict, with a focus on security issues in Asia. Through each of the lessons…

Sustainable Waste Water Treatment in Developing Countries: A Case Study of IIT Kharagpur Campus

NASA Astrophysics Data System (ADS)

Das, Sutapa; Bokshi, Sanjit

2017-06-01

Treatment of wastewater and its reuse in irrigation and agriculture can mitigate the inevitable scarcity of safe drinking water in coming decades. For developing countries like India and especially in its under-privileged regions, it is high time to focus on sustainable wastewater treatment which will be economical and easy to construct, operate and maintain by unskilled users without much dependency on electricity. Addressing this issue, various sustainable methods of wastewater treatment was critically analyzed and the Waste Stabilization Pond system was selected. A facility was designed for 20,000 residents of Indian Institute of Technology Kharagpur campus based on its geo-climatic and wastewater characteristics. Detailed calculations were carried out to demonstrate the effluent quality with reduced BOD and E-coli is suitable for unrestricted irrigation. This project with minor customisation can act as a prototype for adjacent vast rural areas where land is available but water, electricity and skilled technicians are not. If implemented, this project will bear social benefits beyond campus such as water supply to drought prone areas, better harvest and rural employment. Moreover, it underpins government' several initiatives to develop rural infrastructure and inclusive growth of the country.

On the Absolutely Continuous Spectrum of Stark Operators

NASA Astrophysics Data System (ADS)

Perelman, Galina

The stability of the absolutely continuous spectrum of the one-dimensional Stark operator under perturbations of the potential is discussed. The focus is on proving this stability under minimal assumptions on smoothness of the perturbation. A general criterion is presented together with some applications. These include the case of periodic perturbations where we show that any perturbation vL1()∩H-1/2() preserves the a.c. spectrum.

Assessing Locally Focused Stability Operations

DTIC Science & Technology

2014-01-01

Detailed Theory -of-Change Chart RAND RR387-4.2 LFSO actions Immediate goals LFSO main goal Higher -level goals Sustainable stability in region Reduced...projects in the vil- lage, and laying the groundwork for starting a village council. At the higher level, the Theory of Change now documents the assumption... Theory of Change RAND RR387-4.5 LFSO actions Immediate goals Chain of consequences LFSO main goal Higher -level goals HN commandos targeting INS 13

77 FR 33158 - Plumas National Forest, California, Sugarloaf Hazardous Fuels Reduction Project

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-05

... to the economic stability of rural communities through: fuels treatments; group selections (GS); area... (DFPZs), modify fire behavior, promote forest and watershed health, while contributing to the economic stability of rural communities in Plumas County, CA. Fire behavior needs to be modified in selected forest...

18 CFR 380.15 - Siting and maintenance requirements.

Code of Federal Regulations, 2011 CFR

2011-04-01

... rights-of-way and the construction of facilities on their property, so long as the result is consistent... rights-of-way, soil stability and protection of natural vegetation and adjacent resources should be taken... to minimize soil erosion. Upon abandonment, the road area should be restored and stabilized without...

Increase of electrodeposited catalyst stability via plasma grown vertically oriented graphene nanoparticle movement restriction.

PubMed

Vanrenterghem, Bart; Hodnik, Nejc; Bele, Marjan; Šala, Martin; Amelinckx, Giovanni; Neukermans, Sander; Zaplotnik, Rok; Primc, Gregor; Mozetič, Miran; Breugelmans, Tom

2017-08-17

Beside activity, electrocatalyst stability is gaining in importance. The most common degradation mechanism is the loss of the active surface area due to nanoparticle growth via coalescence/agglomeration. We propose a particle confinement strategy via vertically oriented graphene deposition to overcome degradation of the nanoparticles.

Visual Neuroscience: Unique Neural System for Flight Stabilization in Hummingbirds.

PubMed

Ibbotson, M R

2017-01-23

The pretectal visual motion processing area in the hummingbird brain is unlike that in other birds: instead of emphasizing detection of horizontal movements, it codes for motion in all directions through 360°, possibly offering precise visual stability control during hovering. Copyright © 2017 Elsevier Ltd. All rights reserved.

Stability of Behavioral Ratings of Children with SLI.

ERIC Educational Resources Information Center

Redmond, Sean M.; Rice, Mabel L.

2002-01-01

A study investigated the long-term stability of the teacher and parent behavioral ratings of 37 children with specific language impairment. Results indicate diminishment in teacher-reported behavior problems in most areas of socioemotional development from kindergarten to second grade and increasing congruence between teacher and parent ratings.…

Emotional Responsiveness and Emotional Stability in Three Religious Communities of India.

ERIC Educational Resources Information Center

Prakash, Jai; Shukla, Anand Prakash

The present study investigated personality dispositions such as emotional responsiveness and emotional stability in religious communities of India. The religious ideology and particular system of religious practices of each individual may influence his personality structure. A review of the literature shows that studies available in this area have…

Dynamics and control of high area-to-mass ratio spacecraft and its application to geomagnetic exploration

NASA Astrophysics Data System (ADS)

Luo, Tong; Xu, Ming; Colombo, Camilla

2018-04-01

This paper studies the dynamics and control of a spacecraft, whose area-to-mass ratio is increased by deploying a reflective orientable surface such as a solar sail or a solar panel. The dynamical system describing the motion of a non-zero attitude angle high area-to-mass ratio spacecraft under the effects of the Earth's oblateness and solar radiation pressure admits the existence of equilibrium points, whose number and the eccentricity values depend on the semi-major axis, the area-to-mass ratio and the attitude angle of the spacecraft together. When two out of three parameters are fixed, five different dynamical topologies successively occur through varying the third parameter. Two of these five topologies are critical cases characterized by the appearance of the bifurcation phenomena. A conventional Hamiltonian structure-preserving (HSP) controller and an improved HSP controller are both constructed to stabilize the hyperbolic equilibrium point. Through the use of a conventional HSP controller, a bounded trajectory around the hyperbolic equilibrium point is obtained, while an improved HSP controller allows the spacecraft to easily transfer to the hyperbolic equilibrium point and to follow varying equilibrium points. A bifurcation control using topologies and changes of behavior areas can also stabilize a spacecraft near a hyperbolic equilibrium point. Natural trajectories around stable equilibrium point and these stabilized trajectories around hyperbolic equilibrium point can all be applied to geomagnetic exploration.

Suicidal and nonsuicidal adolescents: different factors contribute to self-esteem.

PubMed

Grøholt, Berit; Ekeberg, Oivind; Wichstrøm, Lars; Haldorsen, Tor

2005-10-01

Some risk and protective factors differ in their importance to suicidal and nonsuicidal people. In this research we explore the cross-sectional differences between risk factors among suicidal adolescents and nonsuicidal adolescents by focusing on self-esteem. Sixty-five suicidal and 390 nonsuicidal adolescents were compared on Harter's Self-Perceived Profile for Adolescents, self-concept stability, seeking support, loneliness, and depression. Self-concept stability, loneliness, and peer support correlated differently with self-esteem. In multivariate regression analyses, variance in self-esteem was explained by depression and loneliness, and among nonsuicidal adolescents also by self-concept stability, support, and competencies. Loneliness and self-concept stability related differently to self-esteem in suicidal and nonsuicidal adolescents. When the aim is to enhance self-esteem, this difference may delineate suicidal subgroups that need special interventions.

SPLINTS: small-molecule protein ligand interface stabilizers.

PubMed

Fischer, Eric S; Park, Eunyoung; Eck, Michael J; Thomä, Nicolas H

2016-04-01

Regulatory protein-protein interactions are ubiquitous in biology, and small molecule protein-protein interaction inhibitors are an important focus in drug discovery. Remarkably little attention has been given to the opposite strategy-stabilization of protein-protein interactions, despite the fact that several well-known therapeutics act through this mechanism. From a structural perspective, we consider representative examples of small molecules that induce or stabilize the association of protein domains to inhibit, or alter, signaling for nuclear hormone, GTPase, kinase, phosphatase, and ubiquitin ligase pathways. These SPLINTS (small-molecule protein ligand interface stabilizers) drive interactions that are in some cases physiologically relevant, and in others entirely adventitious. The diverse structural mechanisms employed suggest approaches for a broader and systematic search for such compounds in drug discovery. Copyright © 2016 Elsevier Ltd. All rights reserved.

Robust stochastic stability of discrete-time fuzzy Markovian jump neural networks.

PubMed

Arunkumar, A; Sakthivel, R; Mathiyalagan, K; Park, Ju H

2014-07-01

This paper focuses the issue of robust stochastic stability for a class of uncertain fuzzy Markovian jumping discrete-time neural networks (FMJDNNs) with various activation functions and mixed time delay. By employing the Lyapunov technique and linear matrix inequality (LMI) approach, a new set of delay-dependent sufficient conditions are established for the robust stochastic stability of uncertain FMJDNNs. More precisely, the parameter uncertainties are assumed to be time varying, unknown and norm bounded. The obtained stability conditions are established in terms of LMIs, which can be easily checked by using the efficient MATLAB-LMI toolbox. Finally, numerical examples with simulation result are provided to illustrate the effectiveness and less conservativeness of the obtained results. Copyright © 2014 ISA. Published by Elsevier Ltd. All rights reserved.

Experimental and theoretical investigation of the stability of stepwise pH gradients in continuous flow electrophoresis

NASA Technical Reports Server (NTRS)

Kuhn, Reinhard; Wagner, Horst; Mosher, Richard A.; Thormann, Wolfgang

1987-01-01

Isoelectric focusing in the continuous flow mode can be more quickly and economically performed by admitting a stepwise pH gradient composed of simple buffers instead of uniform mixtures of synthetic carrier ampholytes. The time-consuming formation of the pH gradient by the electric field is thereby omitted. The stability of a three-step system with arginine - morpholinoethanesulfonic acid/glycylglycine - aspartic acid is analyzed theoretically by one-dimensional computer simulation as well as experimentally at various flow rates in a continuous flow apparatus. Excellent agreement between experimental and theoretical data was obtained. This metastable configuration was found to be suitable for focusing of proteins under continuous flow conditions. The influence of various combinations of electrolytes and membranes between electrophoresis chamber and electrode compartments is also discussed.