Consolidation quality and mechanical performance of stamp formed tailored blanks produced by rapid AFP

NASA Astrophysics Data System (ADS)

Slange, T. K.; Warnet, L. L.; Grouve, W. J. B.; Akkerman, R.

2018-05-01

Stamp forming is a rapid manufacturing technology used to shape flat blanks of thermoplastic composite material into three-dimensional components. The combination with rapid AFP as blank manufacturing technology can further extend the applicability of stamp forming by allowing rapid lay-up of tailored blanks and offering partial preconsolidation. In an experimental study it is demonstrated that high quality laminates with good flexural strength can be obtained by following this process route. The consolidation of ply-drop regions is demonstrated by flat laminates with a thickness step. The influence of fiber orientations, blank-tooling misalignments and AFP tolerances is investigated.

Stamping of Thin-Walled Structural Components with Magnesium Alloy AZ31 Sheets

NASA Astrophysics Data System (ADS)

Chen, Fuh-Kuo; Chang, Chih-Kun

2005-08-01

In the present study, the stamping process for manufacturing cell phone cases with magnesium alloy AZ31 sheets was studied using both the experimental approach and the finite element analysis. In order to determine the proper forming temperature and set up a fracture criterion, tensile tests and forming limit tests were first conducted to obtain the mechanical behaviors of AZ31 sheets at various elevated temperatures. The mechanical properties of Z31 sheets obtained from the experiments were then adopted in the finite element analysis to investigate the effects of the process parameters on the formability of the stamping process of cell phone cases. The finite element simulation results revealed that both the fracture and wrinkle defects could not be eliminated at the same time by adjusting blank-holder force or blank size. A drawbead design was then performed using the finite element simulations to determine the size and the location of drawbead required to suppress the wrinkle defect. An optimum stamping process, including die geometry, forming temperature, and blank dimension, was then determined for manufacturing the cell phone cases. The finite element analysis was validated by the good agreement between the simulation results and the experimental data. It confirms that the cell phone cases can be produced with magnesium alloy AZ31 sheet by the stamping process at elevated temperatures.

Force-controlled inorganic crystallization lithography.

PubMed

Cheng, Chao-Min; LeDuc, Philip R

2006-09-20

Lithography plays a key role in integrated circuits, optics, information technology, biomedical applications, catalysis, and separation technologies. However, inorganic lithography techniques remain of limited utility for applications outside of the typical foci of integrated circuit manufacturing. In this communication, we have developed a novel stamping method that applies pressure on the upper surface of the stamp to regulate the dewetting process of the inorganic buffer and the evaporation rate of the solvent in this buffer between the substrate and the surface of the stamp. We focused on generating inorganic microstructures with specific locations and also on enabling the ability to pattern gradients during the crystallization of the inorganic salts. This approach utilized a combination of lithography with bottom-up growth and assembly of inorganic crystals. This work has potential applications in a variety of fields, including studying inorganic material patterning and small-scale fabrication technology.

Influence of preconsolidation on consolidation quality after stamp forming of C/PEEK composites

NASA Astrophysics Data System (ADS)

Slange, T. K.; Warnet, L.; Grouve, W. J. B.; Akkerman, R.

2016-10-01

Stamp forming is a rapid manufacturing technology used to shape flat blanks of thermoplastic composite material into three-dimensional components. Currently, expensive autoclave and press consolidation are used to preconsolidate blanks. This study investigates the influence of preconsolidation on final consolidation quality after stamp forming and explores the potential of alternative blank manufacturing methods that could reduce part costs. Blanks were manufactured using various blank manufacturing methods and subsequently were stamp formed. The consolidation quality both before and after stamp forming was compared, where the focus was on void content as the main measure for consolidation quality. The void content was characterized through thickness and density measurements, as well as by microscopy analysis. Results indicate that preconsolidation quality does have an influence on the final consolidation quality. This is due to the severe deconsolidation and limited reconsolidation during stamp forming. Nevertheless, the potential of automated fiber placement and ultrasonic spot welding as alternative blank manufacturing methods was demonstrated.

Molecular scale modeling of polymer imprint nanolithography.

PubMed

Chandross, Michael; Grest, Gary S

2012-01-10

We present the results of large-scale molecular dynamics simulations of two different nanolithographic processes, step-flash imprint lithography (SFIL), and hot embossing. We insert rigid stamps into an entangled bead-spring polymer melt above the glass transition temperature. After equilibration, the polymer is then hardened in one of two ways, depending on the specific process to be modeled. For SFIL, we cross-link the polymer chains by introducing bonds between neighboring beads. To model hot embossing, we instead cool the melt to below the glass transition temperature. We then study the ability of these methods to retain features by removing the stamps, both with a zero-stress removal process in which stamp atoms are instantaneously deleted from the system as well as a more physical process in which the stamp is pulled from the hardened polymer at fixed velocity. We find that it is necessary to coat the stamp with an antifriction coating to achieve clean removal of the stamp. We further find that a high density of cross-links is necessary for good feature retention in the SFIL process. The hot embossing process results in good feature retention at all length scales studied as long as coated, low surface energy stamps are used.

Architecture for Cyber Defense Simulator in Military Applications

DTIC Science & Technology

2013-06-01

ieeexplore.ieee.org/stamp/stamp.jsp?tp=&arnumber=5977648&isnumber=5977431 [18] Goodall , J.R.; D’Amico, A.; Kopylec, J.K.; , "Camus: Automatically mapping...isnumber=5977431 • [18] Goodall , J.R.; D’Amico, A.; Kopylec, J.K.; , "Camus: Automatically mapping Cyber Assets to Missions and Users," Military

Simulation of springback and microstructural analysis of dual phase steels

NASA Astrophysics Data System (ADS)

Kalyan, T. Sri.; Wei, Xing; Mendiguren, Joseba; Rolfe, Bernard

2013-12-01

With increasing demand for weight reduction and better crashworthiness abilities in car development, advanced high strength Dual Phase (DP) steels have been progressively used when making automotive parts. The higher strength steels exhibit higher springback and lower dimensional accuracy after stamping. This has necessitated the use of simulation of each stamped component prior to production to estimate the part's dimensional accuracy. Understanding the micro-mechanical behaviour of AHSS sheet may provide more accuracy to stamping simulations. This work can be divided basically into two parts: first modelling a standard channel forming process; second modelling the micro-structure of the process. The standard top hat channel forming process, benchmark NUMISHEET'93, is used for investigating springback effect of WISCO Dual Phase steels. The second part of this work includes the finite element analysis of microstructures to understand the behaviour of the multi-phase steel at a more fundamental level. The outcomes of this work will help in the dimensional control of steels during manufacturing stage based on the material's microstructure.

[A new look at the tomb of the physician, Morlongo Venice].

PubMed

Pardon-Labonnelie, Muriel

2014-01-01

The development of the inventory and synthetic study of collyrium stamps, commonly known as "oculist's stamps", includes the physico-chemical analysis of rare stamped collyrium's remains. The fragments of collyrium which were discovered in a tomb of Morlungo (Veneto) are all the more remarkable as the remedy's name stamped on two of them remains enigmatic at the moment and because of the association in a funerary context with an-other thirty-five finds. More specifically, they were discovered near surgical bronze instruments, a large amount of amber, a portable sundial and a seal box. Recent archaeological, textual and technological data thus make the study of the remains of collyriums of Morlungo particularly interesting for the history of medicine.

Verification of Reproduction Simulation of the 2011 Great East Japan Tsunami Using Time-Stamp Data

NASA Astrophysics Data System (ADS)

Honma, Motohiro; Ushiyama, Motoyuki

2014-05-01

In the 2011 off the pacific coast of Tohoku earthquake tsunami, the significant damage and loss of lives were caused by large tsunami in the pacific coastal areas of the northern Japan. It is important to understand the situation of tsunami inundation in detail in order to establish the effective measures of disaster prevention. In this study, we calculated the detailed tsunami inundation simulation of Rikuzentakata city and verified the simulation results using not only the static observed data such as inundation area and tsunami height estimated by traces but also time stamp data which were recorded to digital camera etc. We calculated the tsunami simulation by non-linear long-wave theory using the staggered grid and leap flog scheme. We used Fujii and Satake (2011)'s model ver.4.2 as the tsunami source. The inundation model of Rikuzentakata city was constructed by fine ground level data of 10m mesh. In this simulation, the shore and river banks were set in boundary of calculation mesh. At that time, we have calculated two patterns of simulation, one condition is that a bank doesn't collapse even if tsunami overflows on it, another condition is that a bank collapses if tsunami overflows on it and its discharge exceeds the threshold. We can use the inundation area data, which was obtained by Geospatial Information Authority of Japan (GSI), and height data of tsunami trace, which were obtained by the 2011 Tohoku Earthquake Joint Survey (TTJS) group, as "static" verification data. Comparing the inundation area of simulation result with its observation by GSI, both areas are matched very well. And then, correlation coefficient between tsunami height data resulted from simulation and observed by TTJS is 0.756. In order to verify tsunami arrival time, we used the time stamp data which were recorded to digital camera etc. by citizens. Ushiyama and Yokomaku (2012) collected these tsunami stamp data and estimated the arrival time in Rikuzentakata city. We compared the arrival time resulted from tsunami simulation with estimated by Ushiyama and Yokomaku (2012) for some major points. The arrival time is earlier 2-4 minutes in the condition that a bank collapses when tsunami overflows and its discharge exceeds 0.05m2/s at each mesh boundary than in the condition that a bank doesn't collapse. And, on the whole the arrival time estimated from time stamp data is in accord with the result which were calculated in the condition that a bank collapse. We could verify reproducibility about not only the final tsunami inundation situation but also the temporal change of tsunami inundation situation by using the time stamp data. Acknowledgement In this study, we used tsunami trace data obtained by The 2011 Tohoku Earthquake Tsunami Joint Survey (TTJS) Group. Reference 1) Fujii and Satake: Tsunami Source of the Off Tohoku-Pacific Earthquake on March 11, 2011, http://iisee.kenken.go.jp/staff/fujii/OffTohokuPacific2011/tsunami_ja_ver4.2and4.6.html, 2011. 2) Ushiyama and Yokomaku: Estimation of situation in Rikuzentakata city just before tsunami attack based on time stamp data, J.JSNDS31-1, pp.47-58, 2012.

Safety Guided Design of Crew Return Vehicle in Concept Design Phase Using STAMP/STPA

NASA Astrophysics Data System (ADS)

Nakao, H.; Katahira, M.; Miyamoto, Y.; Leveson, N.

2012-01-01

In the concept development and design phase of a new space system, such as a Crew Vehicle, designers tend to focus on how to implement new technology. Designers also consider the difficulty of using the new technology and trade off several system design candidates. Then they choose an optimal design from the candidates. Safety should be a key aspect driving optimal concept design. However, in past concept design activities, safety analysis such as FTA has not used to drive the design because such analysis techniques focus on component failure and component failure cannot be considered in the concept design phase. The solution to these problems is to apply a new hazard analysis technique, called STAMP/STPA. STAMP/STPA defines safety as a control problem rather than a failure problem and identifies hazardous scenarios and their causes. Defining control flow is the essential in concept design phase. Therefore STAMP/STPA could be a useful tool to assess the safety of system candidates and to be part of the rationale for choosing a design as the baseline of the system. In this paper, we explain our case study of safety guided concept design using STPA, the new hazard analysis technique, and model-based specification technique on Crew Return Vehicle design and evaluate benefits of using STAMP/STPA in concept development phase.

Development of Methods and Equipment for Sheet Stamping

NASA Astrophysics Data System (ADS)

Botashev, A. Yu; Bisilov, N. U.; Malsugenov, R. S.

2018-03-01

New methods of sheet stamping were developed: the gas forming with double-sided heating of a blank part and the gas molding with backpressure. In case of the first method the blank part is heated to the set temperature by means of a double-sided impact of combustion products of gas mixtures, after which, under the influence of gas pressure a stamping process is performed. In case of gas molding with backpressure, the blank part is heated to the set temperature by one-sided impact of the combustion products, while backpressure is created on the opposite side of the blank part by compressed air. In both methods the deformation takes place in the temperature range of warm or hot treatment due to the heating of a blank part. This allows one to form parts of complicated shape within one technological operation, which significantly reduces the cost of production. To implement these methods, original devices were designed and produced, which are new types of forging and stamping equipment. Using these devices, an experimental research on the stamping process was carried out and high-quality parts were obtained, which makes it possible to recommend the developed methods of stamping in the industrial production. Their application in small-scale production will allow one to reduce the cost price of stamped parts 2 or 3 times.

High sensitivity, high surface area Enzyme-linked Immunosorbent Assay (ELISA).

PubMed

Singh, Harpal; Morita, Takahiro; Suzuki, Yuma; Shimojima, Masayuki; Le Van, An; Sugamata, Masami; Yang, Ming

2015-01-01

Enzyme-linked immunosorbent assays (ELISA) are considered the gold standard in the demonstration of various immunological reactions with an application in the detection of infectious diseases such as during outbreaks or in patient care. This study aimed to produce an ELISA-based diagnostic with an increased sensitivity of detection compared to the standard 96-well method in the immunologic diagnosis of infectious diseases. A '3DStack' was developed using readily available, low cost fabrication technologies namely nanoimprinting and press stamping with an increased surface area of 4 to 6 times more compared to 96-well plates. This was achieved by stacking multiple nanoimprinted polymer sheets. The flow of analytes between the sheets was enhanced by rotating the 3DStack and confirmed by Finite-Element (FE) simulation. An Immunoglobulin G (IgG) ELISA for the detection of antibodies in human serum raised against Rubella virus was performed for validation. An improved sensitivity of up to 1.9 folds higher was observed using the 3DStack compared to the standard method. The increased surface area of the 3DStack developed using nanoimprinting and press stamping technologies, and the flow pattern between sheets generated by rotating the 3DStack were potential contributors to a more sensitive ELISA-based diagnostic device.

Experimental and Numerical Studies on the Formability of Materials in Hot Stamping and Cold Die Quenching Processes

NASA Astrophysics Data System (ADS)

Li, N.; Mohamed, M. S.; Cai, J.; Lin, J.; Balint, D.; Dean, T. A.

2011-05-01

Formability of steel and aluminium alloys in hot stamping and cold die quenching processes is studied in this research. Viscoplastic-damage constitutive equations are developed and determined from experimental data for the prediction of viscoplastic flow and ductility of the materials. The determined unified constitutive equations are then implemented into the commercial Finite Element code Abaqus/Explicit via a user defined subroutine, VUMAT. An FE process simulation model and numerical procedures are established for the modeling of hot stamping processes for a spherical part with a central hole. Different failure modes (failure takes place either near the central hole or in the mid span of the part) are obtained. To validate the simulation results, a test programme is developed, a test die set has been designed and manufactured, and tests have been carried out for the materials with different forming rates. It has been found that very close agreements between experimental and numerical process simulation results are obtained for the ranges of temperatures and forming rates carried out.

Numerical simulation of temperature field, microstructure evolution and mechanical properties of HSS during hot stamping

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shi, Dongyong; Liu, Wenquan; Ying, Liang, E-mail: pinghu@dlut.edu.cn

The hot stamping of boron steels is widely used to produce ultra high strength automobile components without any spring back. The ultra high strength of final products is attributed to the fully martensitic microstructure that is obtained through the simultaneous forming and quenching of the hot blanks after austenization. In the present study, a mathematical model incorporating both heat transfer and the transformation of austenite is presented. A FORTRAN program based on finite element technique has been developed which permits the temperature distribution and microstructure evolution of high strength steel during hot stamping process. Two empirical diffusion-dependent transformation models undermore » isothermal conditions were employed respectively, and the prediction capability on mechanical properties of the models were compared with the hot stamping experiment of an automobile B-pillar part.« less

Applying the Theory of Diffusion of Innovations to Understand Electronic Benefit Transfer Technology Adoption at Mid-West Farmers Markets

ERIC Educational Resources Information Center

Hasin, Afroza

2016-01-01

The Supplemental Nutrition Assistance Program (SNAP, previously "food stamps"), is the nation's largest federal entitlement nutritional assistance program which assists individuals and households living below the federal poverty level in order to reduce the amount of money they spend on food. With the conversion of food stamps coupons to…

Investigation of the Phase Formation of AlSi-Coatings for Hot Stamping of Boron Alloyed Steel

NASA Astrophysics Data System (ADS)

Veit, R.; Hofmann, H.; Kolleck, R.; Sikora, S.

2011-01-01

Hot stamping of boron alloyed steel is gaining more and more importance for the production of high strength automotive body parts. Within hot stamping of quenchenable steels the blank is heated up to austenitization temperature, transferred to the tool, formed rapidly and quenched in the cooled tool. To avoid scale formation during the heating process of the blank, the sheet metal can be coated with an aluminium-silicum alloy. The meltimg temperature of this coating is below the austenitization temperature of the base material. This means, that a diffusion process between base material and coating has to take place during heating, leading to a higher melting temperature of the coating. In conventional heating devices, like roller hearth furnaces, the diffusion process is reached by relatively low heating rates. New technologies, like induction heating, reach very high heating rates and offer great potentials for the application in hot stamping. Till now it is not proofed, that this technology can be used with aluminum-silicon coated materials. This paper will present the results of comparative heating tests with a conventional furnace and an induction heating device. For different time/temperature-conditions the phase formation within the coating will be described.

Effects of Blank Curvature and Tool Conditions on the Spring Back of Thin Sheet Panel Formed through Local Embossing and Edge L-Bending

NASA Astrophysics Data System (ADS)

Park, Keecheol; Park, Jongyoun; Nam, Jaebok

2011-08-01

Due to the application of thinner sheet steels, the stamped panels in the forming process, generally, are severely distorted. The wavy shape of embossed panel finally converted to residual stress embedded in the panel at final forming (edge L-bending) and it is known as the cause of twisting and oil canning of spring backed panel. Another important source of stamped shape deviation is the curvature of blank. The effects of blank curvature on the shape defects (panel curvature and twisting) after stamping were investigated from defective panel analysis, model experiment and stamping simulation. And the effect of tool conditions (BHF and bead height change) on spring backed shape of real TV bottom chassis were studied. The initial curvature of blank was remained in the flat area of stamped panels as width directional curvature. It converted from length direction curvature of blank. The curvature of initial blank reduced the wavy shape after local emboss forming, but twisting after edge L-bending was increased at large blank curvature cases. The effects of emboss forming conditions, the forming heights and blank holding force were studied and it was found that the wavy shape of stamped sheet was rapidly changed although the forming conditions altered very small amount.

Estimation Model for Magnetic Properties of Stamped Electrical Steel Sheet

NASA Astrophysics Data System (ADS)

Kashiwara, Yoshiyuki; Fujimura, Hiroshi; Okamura, Kazuo; Imanishi, Kenji; Yashiki, Hiroyoshi

Less deterioration in magnetic properties of electrical steel sheets in the process of stamping out iron-core are necessary in order to maintain its performance. First, the influence of plastic strain and stress on magnetic properties was studied by test pieces, in which plastic strain was added uniformly and residual stress was not induced. Because the influence of plastic strain was expressed by equivalent plastic strain, at each equivalent plastic strain state the influence of load stress was investigated. Secondly, elastic limit was determined about 60% of macroscopic yield point (MYP), and it was found to agree with stress limit inducing irreversible deterioration in magnetic properties. Therefore simulation models, where beyond elastic limit plastic deformation begins and magnetic properties are deteriorated steeply, are proposed. Besides considered points in the deformation analysis are strain-rate sensitivity of flow stress, anisotropy under deformation, and influence of stress triaxiality on fracture. Finally, proposed models have been shown to be valid, because magnetic properties of 5mm width rectangular sheets stamped out from non-oriented electrical steel sheet (35A250 JIS grade) can be estimated with good accuracy. It is concluded that the elastic limit must be taken into account in both stamping process simulation and magnetic field calculation.

Research on the Micro Sheet Stamping Process Using Plasticine as Soft Punch

PubMed Central

Wang, Xiao; Zhang, Di; Gu, Chunxing; Shen, Zongbao; Liu, Huixia

2014-01-01

Plasticine is widely used in the analysis of metal forming processes, due to its excellent material flow ability. In this study, plasticine is used as the soft punch to fabricate array micro-channels on metal sheet in the micro sheet stamping process. This is because plasticine can produce a large material flow after being subjected to force and through the material flow, the plasticine can cause the sheet to fill into the micro-channels of the rigid die, leading to the generation of micro-channels in the sheet. The distribution of array micro-channels was investigated as well as the influence of load forces on the sheet deformations. It was found that the depth of micro-channels increases as the load force increases. When the load force reaches a certain level, a crack can be observed. The micro sheet stamping process was also investigated by the method of numerical simulation. The obtained experimental and numerical results for the stamping process showed that they were in good agreement. Additionally, from the simulation results, it can be seen that the corner region of the micro-channel-shape work piece has a risk to crack due to the existence of maximum von Mises stress and significant thinning. PMID:28788668

Simulation-Driven Design Approach for Design and Optimization of Blankholder

NASA Astrophysics Data System (ADS)

Sravan, Tatipala; Suddapalli, Nikshep R.; Johan, Pilthammar; Mats, Sigvant; Christian, Johansson

2017-09-01

Reliable design of stamping dies is desired for efficient and safe production. The design of stamping dies are today mostly based on casting feasibility, although it can also be based on criteria for fatigue, stiffness, safety, economy. Current work presents an approach that is built on Simulation Driven Design, enabling Design Optimization to address this issue. A structural finite element model of a stamping die, used to produce doors for Volvo V70/S80 car models, is studied. This die had developed cracks during its usage. To understand the behaviour of stress distribution in the stamping die, structural analysis of the die is conducted and critical regions with high stresses are identified. The results from structural FE-models are compared with analytical calculations pertaining to fatigue properties of the material. To arrive at an optimum design with increased stiffness and lifetime, topology and free-shape optimization are performed. In the optimization routine, identified critical regions of the die are set as design variables. Other optimization variables are set to maintain manufacturability of the resultant stamping die. Thereafter a CAD model is built based on geometrical results from topology and free-shape optimizations. Then the CAD model is subjected to structural analysis to visualize the new stress distribution. This process is iterated until a satisfactory result is obtained. The final results show reduction in stress levels by 70% with a more homogeneous distribution. Even though mass of the die is increased by 17 %, overall, a stiffer die with better lifetime is obtained. Finally, by reflecting on the entire process, a coordinated approach to handle such situations efficiently is presented.

Additional security features for optically variable foils

NASA Astrophysics Data System (ADS)

Marshall, Allan C.; Russo, Frank

1998-04-01

For thousands of years, man has exploited the attraction and radiance of pure gold to adorn articles of great significance. Today, designers decorate packaging with metallic gold foils to maintain the prestige of luxury items such as perfumes, chocolates, wine and whisky, and to add visible appeal and value to wide range of products. However, today's products do not call for the hand beaten gold leaf of the Ancient Egyptians, instead a rapid production technology exists which makes use of accurately coated thin polymer films and vacuum deposited metallic layers. Stamping Foils Technology is highly versatile since several different layers may be combined into one product, each providing a different function. Not only can a foil bring visual appeal to an article, it can provide physical and chemical resistance properties and also protect an article from human forms of interference, such as counterfeiting, copying or tampering. Stamping foils have proved to be a highly effective vehicle for applying optical devices to items requiring this type of protection. Credit cards, bank notes, personal identification documents and more recently high value packaged items such as software and perfumes are protected by optically variable devices applied using stamping foil technology.

Development of a high hertz-stress contact for conventional batch production using a unique scribing technology

NASA Astrophysics Data System (ADS)

Bhuiyan, M. M. I.; Alamgir, T.; Bhuiyan, M.; Kajihara, M.

2013-12-01

Gradually the electronic devices are getting more compact dimension with respect to the width and thickness. As a result, the contacts are becoming thinner and which leads the contact to be loose and unstable contact. In comercial stamping methode, connector tip diameter should be more than 300μm due to its size limitation. Consequently, the connector contact resistance is becoming higher due to weak contact force. To overcome this problem there were few more basic research using MEMS and Electro Fine Forming (EFF) technology to make high Hertz-Stress Contact (5μm) due to the limitation in the commercial stamping process and the result was in satisfactory level. However, since the MEMS and EFF fabrication is costly therefore, a new method is introduced in this paper using the commercial Phosphor Bronze stamping method to reduce the production cost. Moreover, scribing method is used to make tip on the contact. Accordingly, more compact fine pitch contact is successfully fabricated and tested with 5μm High Hertz Stress without using the MEMS and EFF technology. Hence the manufactured contact resistance becomes less than 20mΩ ±5mΩ.

Influence of Plastic Deformation on Martensitic Transformation During Hot Stamping of Complex Structure Auto Parts

NASA Astrophysics Data System (ADS)

Shen, Yuhan; Song, Yanli; Hua, Lin; Lu, Jue

2017-04-01

The ultra-high strength steel auto parts manufactured by hot stamping are widely applied for weight reduction and safety improvement. During the hot stamping process, hot forming and quenching are performed in one step wherein plastic deformation and phase transformation simultaneously take place and affect each other. Thereinto, the influence of deformation on martensitic transformation is of great importance. In the present paper, the influence of plastic deformation on martensitic transformation during hot stamping of complex structure auto parts was investigated. For this purpose, a B-pillar reinforced panel in B1500HS steel was manufactured by hot stamping, and the process was simulated by finite element software based on a thermo-mechanical-metallurgical coupled model. Considering various deformation degrees, the microstructures and mechanical properties at four typical locations of the hot stamped B-pillar reinforced panel were detected. The results show that the martensitic content and the microhardness increase with the increase in the deformation amount. There are two reasons causing this phenomenon: (1) the increase in mechanical driving force and (2) the increased probability of the martensitic nucleation at crystal defects. The x-ray diffraction analysis indicates the carbon enrichment in retained austenite which results from the carbon diffusion during the low-carbon martensite formation. Furthermore, the carbon content decreases with the increase in the deformation amount, because the deformation of austenite suppresses the carbon diffusion.

Forming simulation of woven composite fibers and its influence on structural performance

NASA Astrophysics Data System (ADS)

Divine, Vincent; Beauchesne, Erwan; Roy, Subir; Palaniswamy, Hariharasudhan

2013-12-01

In recent years, the interest in composite material as a replacement for metals has been growing. The automotive industry, in its constant quest for weight reduction, is now seriously considering composite materials as a substitute for sheet metal components to meet future fuel consumption standards. However, composite forming processes are expensive and difficult to control because of its complex composition with fiber and matrix layers or plies and its dependency on many parameters, such as non-linearity of tensile stiffness, effect of shear rate, temperature and friction. Hence, numerical simulation could be a viable approach to predict material behavior during composite forming. The objective of this study is to highlight capabilities of RADIOSS®, a non-linear finite element analysis based structural solver commonly used for stamping and crash analyses, to simulate forming simulation of composite plies made from woven fibers. For validation the well-known double dome model is used with material data published in NUMISHEET'05 proceedings. It is modeled as a woven fabric with an elastic anisotropic fabric material law available in RADIOSS. This material law is able to consider properties along the two directions of anisotropy, warp and weft. The compared result is the shear angle after stamping that is, the variation of angle between warp and weft fibers, at several prescribed points on the ply. The variation of this angle has a strong impact on material characteristics which severely deteriorates when a critical value is reached. Hence, a study on crash simulations is performed, after mapping fibers angles from stamping simulation.

"No Taxation without Representation:" A Simulation Activity.

ERIC Educational Resources Information Center

Schur, Joan Brodsky

1992-01-01

Describes a simulation exercise designed to help students understand the objections of U.S. colonists to the Stamp Act and other taxes. Includes a sample handout, instructions for the teacher in carrying out the simulation, and questions to compare students' and colonists' about feelings being assessed fees unfairly. (DK)

Combined stamping-forging for non-axisymmetric product

NASA Astrophysics Data System (ADS)

Taureza, Muhammad; Danno, Atsushi; Song, Xu; Oh, Jin An

2016-10-01

Successive combined stamping-forging (CSF) is proposed to produce multi-thickness non-axisymmetric components. This method involves successive compression to create exclusively outward metal flow. Hitherto, the development of CSF has been mostly done for axisymmetric geometry. Using this technique, defect-free rectangular case component with length to thickness ratio of 40 is produced with lower forging pressure. This technology has potential for high throughput production of parts with multiple thicknesses and high width to thickness ratio.

Nuclear Thermal Rocket Element Environmental Simulator (NTREES) Upgrade Activities

NASA Technical Reports Server (NTRS)

Emrich, William

2013-01-01

A key technology element in Nuclear Thermal Propulsion is the development of fuel materials and components which can withstand extremely high temperatures while being exposed to flowing hydrogen. NTREES provides a cost effective method for rapidly screening of candidate fuel components with regard to their viability for use in NTR systems. The NTREES is designed to mimic the conditions (minus the radiation) to which nuclear rocket fuel elements and other components would be subjected to during reactor operation. The NTREES consists of a water cooled ASME code stamped pressure vessel and its associated control hardware and instrumentation coupled with inductive heaters to simulate the heat provided by the fission process. The NTREES has been designed to safely allow hydrogen gas to be injected into internal flow passages of an inductively heated test article mounted in the chamber.

Large area in situ fabrication of poly(pyrrole)-nanowires on flexible thermoplastic films using nanocontact printing

NASA Astrophysics Data System (ADS)

Garcia-Cruz, Alvaro; Lee, Michael; Marote, Pedro; Zine, Nadia; Sigaud, Monique; Bonhomme, Anne; Pruna, Raquel; Lopez, Manuel; Bausells, Joan; Jaffrezic, Nicole; Errachid, Abdelhamid

2016-08-01

Highly efficient nano-engineering tools will certainly revolutionize the biomedical and sensing devices research and development in the years to come. Here, we present a novel high performance conducting poly(pyrrole) nanowires (PPy-NW) patterning technology on thermoplastic surfaces (poly(ethylene terephthalate (PETE), poly(ethylene 2,6-naphthalate (PEN), polyimide (PI), and cyclic olefin copolymer) using nanocontact printing and controlled chemical polymerization (nCP-CCP) technique. The technique uses a commercial compact disk as a template to produce nanopatterned polydimethylsiloxane (PDMS) stamps. The PDMS nanopatterned stamp was applied to print the PPy-NWs and the developed technology of nCP-CCP produced 3D conducting nanostructures. This new and very promising nanopatterning technology was achieved in a single step and with a low cost of fabrication over large areas.

Damage and Failure Analysis of AZ31 Alloy Sheet in Warm Stamping Processes

NASA Astrophysics Data System (ADS)

Zhao, P. J.; Chen, Z. H.; Dong, C. F.

2016-07-01

In this study, a combined experimental-numerical investigation on the failure of AZ31 Mg alloy sheet in the warm stamping process was carried out based on modified GTN damage model which integrated Yld2000 anisotropic yield criterion. The constitutive equations of material were implemented into a VUMAT subroutine for solver ABAQUS/Explicit and applied to the formability analysis of mobile phone shell. The morphology near the crack area was observed using SEM, and the anisotropic damage evolution at various temperatures was simulated. The distributions of plastic strain, damage evolution, thickness, and fracture initiation obtained from FE simulation were analyzed. The corresponding forming limit diagrams were worked out, and the comparison with the experimental data showed a good agreement.

Investigation of the influence of process parameters on adhesive wear under hot stamping conditions

NASA Astrophysics Data System (ADS)

Schwingenschlögl, P.; Weldi, M.; Merklein, M.

2017-09-01

Current challenges like increasing safety standards and reducing fuel consumption motivate lightweight construction in modern car bodies. Besides using lightweight workpiece materials like aluminum, hot stamping has been established as a key technology for producing safety relevant components. Producing hot stamped parts out of ultra-high strength steels offers the possibility to improve the crash performance. At the same time the weight of car structure is reduced by using thinner sheet thicknesses. In order to avoid oxide scale formation and ensure corrosion protection, AlSi coatings are commonly deposited on the sheet surfaces used for direct hot stamping. This workpiece coating has a critical impact on the tribological conditions within the forming process and, as a consequence, influences the quality of hot stamped parts as well as tool wear. AlSi coatings have been identified as major reason for adhesive wear, which represents the main wear mechanism in hot stamping. Within this study, the influence of the process parameters on adhesive wear are investigated in dependency of workpiece and tool temperatures, drawing velocities and contact pressures. The tribological behavior is analyzed based on strip drawing experiments under direct hot stamping conditions. The experiments are performed with AlSi coated 22MnB5 in contact with the hot working tool steel 1.2367. For analyzing the amount of adhesion on the friction jaws, the surfaces are characterized by optical measurements. The experiments indicate that higher workpiece temperatures cause severe adhesive wear on the tool surface, while an increase of drawing velocity or contact pressure led to reduced adhesion. The measured friction coefficients decreased with rising amount of adhesion and remained at a constant level after a certain adhesive layer was built up on the tool surface.

Knowledge Based Cloud FE Simulation of Sheet Metal Forming Processes.

PubMed

Zhou, Du; Yuan, Xi; Gao, Haoxiang; Wang, Ailing; Liu, Jun; El Fakir, Omer; Politis, Denis J; Wang, Liliang; Lin, Jianguo

2016-12-13

The use of Finite Element (FE) simulation software to adequately predict the outcome of sheet metal forming processes is crucial to enhancing the efficiency and lowering the development time of such processes, whilst reducing costs involved in trial-and-error prototyping. Recent focus on the substitution of steel components with aluminum alloy alternatives in the automotive and aerospace sectors has increased the need to simulate the forming behavior of such alloys for ever more complex component geometries. However these alloys, and in particular their high strength variants, exhibit limited formability at room temperature, and high temperature manufacturing technologies have been developed to form them. Consequently, advanced constitutive models are required to reflect the associated temperature and strain rate effects. Simulating such behavior is computationally very expensive using conventional FE simulation techniques. This paper presents a novel Knowledge Based Cloud FE (KBC-FE) simulation technique that combines advanced material and friction models with conventional FE simulations in an efficient manner thus enhancing the capability of commercial simulation software packages. The application of these methods is demonstrated through two example case studies, namely: the prediction of a material's forming limit under hot stamping conditions, and the tool life prediction under multi-cycle loading conditions.

Knowledge Based Cloud FE Simulation of Sheet Metal Forming Processes

PubMed Central

Zhou, Du; Yuan, Xi; Gao, Haoxiang; Wang, Ailing; Liu, Jun; El Fakir, Omer; Politis, Denis J.; Wang, Liliang; Lin, Jianguo

2016-01-01

The use of Finite Element (FE) simulation software to adequately predict the outcome of sheet metal forming processes is crucial to enhancing the efficiency and lowering the development time of such processes, whilst reducing costs involved in trial-and-error prototyping. Recent focus on the substitution of steel components with aluminum alloy alternatives in the automotive and aerospace sectors has increased the need to simulate the forming behavior of such alloys for ever more complex component geometries. However these alloys, and in particular their high strength variants, exhibit limited formability at room temperature, and high temperature manufacturing technologies have been developed to form them. Consequently, advanced constitutive models are required to reflect the associated temperature and strain rate effects. Simulating such behavior is computationally very expensive using conventional FE simulation techniques. This paper presents a novel Knowledge Based Cloud FE (KBC-FE) simulation technique that combines advanced material and friction models with conventional FE simulations in an efficient manner thus enhancing the capability of commercial simulation software packages. The application of these methods is demonstrated through two example case studies, namely: the prediction of a material's forming limit under hot stamping conditions, and the tool life prediction under multi-cycle loading conditions. PMID:28060298

To Pluto by way of a postage stamp

NASA Technical Reports Server (NTRS)

Staehle, Robert L.; Terrile, Richard J.; Weinstein, Stacy S.

1994-01-01

In this time of constrained budgets, the primary question facing planetary explorers is not 'Can we do it?' but 'Can we do it cheaply?' Taunted by words on a postage stamp, a group of mission designers at the Jet Propulsion Laboratory is struggling to find a cheap way to go to Pluto. Three primary goals were set by the science community: (1) imaging of Pluto and Charon, (2) mapping their surface composition, and (3) characterizing Pluto's atmosphere. The spacecraft will be designed around these primary goals. With the help of the Advanced Technology Insertion (ATI) process $5 million was alloted for two years to shop for lightweight components and subsystems using new technology never tried on a planetary mission. The process for this search and development is described.

Failure Mechanisms of the Protective Coatings for the Hot Stamping Applications

NASA Astrophysics Data System (ADS)

Zhao, Chen

In the present study, four different nitriding techniques were carried on the ductile irons NAAMS-D6510 and cast steels NAAMS-S0050A, which are widely used stamping die materials; duplex treatments (PVD CrN coating+nitriding) were carried on H13 steels, which are common inserts for the hot stamping dies. Inclined impact-sliding wear tests were performed on the nitriding cases under simulated stamping conditions. Surface profilometer, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS) were used to investigate the wear and failure mechanisms of the protective coatings. It was found that the nitrided ductile iron samples performed better than the nitrided cast steel specimens. High temperature inclined impact-sliding wear tests were carried out on the CrN coatings. It was found that the coating performed better at elevated temperature. XPS analysis indicated the top surface layer (about 3-4nm) of the coating was oxidized at 400 °C and formed a Cr2O3 protective film. The in-situ formation of the thin Cr2O3 protective layer likely led to the change of wear mechanisms from severe adhesive failure to mild abrasive wear.

SCIL nanoimprint solutions: high-volume soft NIL for wafer scale sub-10nm resolution

NASA Astrophysics Data System (ADS)

Voorkamp, R.; Verschuuren, M. A.; van Brakel, R.

2016-10-01

Nano-patterning materials and surfaces can add unique functionalities and properties which cannot be obtained in bulk or micro-structured materials. Examples range from hetro-epitaxy of semiconductor nano-wires to guiding cell expression and growth on medical implants. [1] Due to the cost and throughput requirements conventional nano-patterning techniques such as deep UV lithography (cost and flat substrate demands) and electron-beam lithography (cost, throughput) are not an option. Self-assembly techniques are being considered for IC manufacturing, but require nano-sized guiding patterns, which have to be fabricated in any case.[2] Additionally, the self-assembly process is highly sensitive to the environment and layer thickness, which is difficult to control on non-flat surfaces such as PV silicon wafers or III/V substrates. Laser interference lithography can achieve wafer scale periodic patterns, but is limited by the throughput due to intensity of the laser at the pinhole and only regular patterns are possible where the pattern fill fraction cannot be chosen freely due to the interference condition.[3] Nanoimprint lithography (NIL) is a promising technology for the cost effective fabrication of sub-micron and nano-patterns on large areas. The challenges for NIL are related to the technique being a contact method where a stamp which holds the patterns is required to be brought into intimate contact with the surface of the product. In NIL a strong distinction is made between the type of stamp used, either rigid or soft. Rigid stamps are made from patterned silicon, silica or plastic foils and are capable of sub-10nm resolution and wafer scale patterning. All these materials behave similar at the micro- to nm scale and require high pressures (5 - 50 Bar) to enable conformal contact to be made on wafer scales. Real world conditions such as substrate bow and particle contaminants complicate the use of rigid stamps for wafer scale areas, reducing stamp lifetime and yield. Soft stamps, usually based on silicone rubber, behave fundamentally different compared to rigid stamps on the macro-, micro- and nanometer level. The main limitation of traditional silicones is that they are too soft to support sub-micron features against surface tension based stamp deformation and collapse [4] and handling a soft stamp to achieve accurate feature placement on wafer scales to allow overlay alignment with sub-100nm overlay accuracy.

Quenching and Partitioning Process Development to Replace Hot Stamping of High Strength Automotive Steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

De Moor, Emmanuel

The present project investigated Quenching and Partitioning (Q&P) to process cold rolled steels to develop high strength sheet steels that exhibit superior ductility compared to available grades with the intent to allow forming of high strength parts at room temperature to provide an alternative to hot stamping of parts. Hot stamping of boron alloyed steel is the current technology to manufacture thinner gauge sections in automotive structures to guarantee anti-intrusion during collisions whilst improving fuel efficiency by decreasing vehicle weight. Hot stamping involves reheating steel to 900 °C or higher followed by deformation and quenching in the die to producemore » ultra-high strength materials. Hot stamping requires significant energy to reheat the steel and is less productive than traditional room temperature stamping operations. Stamping at elevated temperature was developed due to the lack of available steels with strength levels of interest possessing sufficient ductility enabling traditional room temperature forming. This process is seeing growing demand within the automotive industry and, given the reheating step in this operation, increased energy consumption during part manufacturing results. The present research program focused on the development of steel grades via Q&P processing that exhibit high strength and formability enabling room temperature forming to replace hot stamping. The main project objective consisted of developing sheet steels exhibiting minimum ultimate tensile strength levels of 1200 MPa in combination with minimum tensile elongation levels of 15 pct using Q&P processing through judicious alloy design and heat treating parameter definition. In addition, detailed microstructural characterization and study of properties, processing and microstructure interrelationships were pursued to develop strategies to further enhance tensile properties. In order to accomplish these objectives, alloy design was conducted towards achieving the target properties. Twelve alloys were designed and laboratory produced involving melting, alloying, casting, hot rolling, and cold rolling to obtain sheet steels of approximately 1 mm thickness. Q&P processing of the samples was then conducted. Target properties were achieved and substantially exceeded demonstrating success in the developed and employed alloy design approaches. The best combinations of tensile properties were found at approximately 1550 MPa with a total elongation in excess of 20 pct clearly showing the potential for replacement of hot stamping to produce advanced high strength steels.« less

Finite Element Modelling Full Vehicle Side Impact with Ultrahigh Strength Hot Stamped Steels

NASA Astrophysics Data System (ADS)

Taylor, T.; Fourlaris, G.; Cafolla, J.

2016-10-01

"Hot stamped boron steel" 22MnB5 has been imperative in meeting the automotive industry's demand for materials exhibiting higher tensile strength in the final component. In this paper, the crash performance of three experimental grades developed for automotive hot stamping technologies, exhibiting wider tensile property ranges than 22MnB5, was validated by finite element modelling full vehicle side impact with the experimental material data applied to the B-pillar reinforcement. The superior anti-intrusive crash performance of grade 38MnB5 was demonstrated, with 11 mm less intrusion of the B-pillar reinforcement compared to 22MnB5. Moreover, the superior "impact-energy absorptive" crash performance of grade 15MnCr5 was demonstrated, with 0.15 kJ greater impact-energy absorption by the B-pillar reinforcement compared to 22MnB5.

Large area nanoimprint by substrate conformal imprint lithography (SCIL)

NASA Astrophysics Data System (ADS)

Verschuuren, Marc A.; Megens, Mischa; Ni, Yongfeng; van Sprang, Hans; Polman, Albert

2017-06-01

Releasing the potential of advanced material properties by controlled structuring materials on sub-100-nm length scales for applications such as integrated circuits, nano-photonics, (bio-)sensors, lasers, optical security, etc. requires new technology to fabricate nano-patterns on large areas (from cm2 to 200 mm up to display sizes) in a cost-effective manner. Conventional high-end optical lithography such as stepper/scanners is highly capital intensive and not flexible towards substrate types. Nanoimprint has had the potential for over 20 years to bring a cost-effective, flexible method for large area nano-patterning. Over the last 3-4 years, nanoimprint has made great progress towards volume production. The main accelerator has been the switch from rigid- to wafer-scale soft stamps and tool improvements for step and repeat patterning. In this paper, we discuss substrate conformal imprint lithography (SCIL), which combines nanometer resolution, low patterns distortion, and overlay alignment, traditionally reserved for rigid stamps, with the flexibility and robustness of soft stamps. This was made possible by a combination of a new soft stamp material, an inorganic resist, combined with an innovative imprint method. Finally, a volume production solution will be presented, which can pattern up to 60 wafers per hour.

Investigation of Hardness Change for Spot Welded Tailored Blank in Hot Stamping Using CCT and Deformation-CCT Diagrams

NASA Astrophysics Data System (ADS)

Yogo, Yasuhiro; Kurato, Nozomi; Iwata, Noritoshi

2018-04-01

When an outer panel of a B-pillar is manufactured with the hot stamping process, reinforcements are spot welded on its inner side. Before reinforcements are added, the microstructure of the outer panel is martensite. However, reheating during spot welding changes the martensite to ferrite, which has a lower hardness in the heat-affected zone than in other areas. If spot welding is conducted before hot stamping for making a spot welded tailored blank, the microstructure in the spot welded tailored blank after hot stamping is martensite. This sequence of processes avoids hardness reduction due to spot welding. In this study, the hardness and microstructure around spot welded parts of the tailored blank were investigated. The results clearly showed that areas close to the spot welded parts are severely stretched during hot stamping. In addition, stretching suppresses the martensitic phase transformation and reduces the hardness. To characterize this phenomenon, a simulation was conducted that considered the effects of pre-strain on the phase transformation. A continuous cooling transformation (CCT) diagram and a deformation continuous cooling transformation (DCCT) diagram were made in order to quantify the effect of the cooling rate and pre-strain on the phase transformation and hardness. The hardness was then calculated using the experimentally measured CCT and DCCT diagrams and the finite element analysis results. The calculated hardness was compared with the experimental hardness. Good agreement was found between the calculated and experimental results.

Investigation of Hardness Change for Spot Welded Tailored Blank in Hot Stamping Using CCT and Deformation-CCT Diagrams

NASA Astrophysics Data System (ADS)

Yogo, Yasuhiro; Kurato, Nozomi; Iwata, Noritoshi

2018-06-01

When an outer panel of a B-pillar is manufactured with the hot stamping process, reinforcements are spot welded on its inner side. Before reinforcements are added, the microstructure of the outer panel is martensite. However, reheating during spot welding changes the martensite to ferrite, which has a lower hardness in the heat-affected zone than in other areas. If spot welding is conducted before hot stamping for making a spot welded tailored blank, the microstructure in the spot welded tailored blank after hot stamping is martensite. This sequence of processes avoids hardness reduction due to spot welding. In this study, the hardness and microstructure around spot welded parts of the tailored blank were investigated. The results clearly showed that areas close to the spot welded parts are severely stretched during hot stamping. In addition, stretching suppresses the martensitic phase transformation and reduces the hardness. To characterize this phenomenon, a simulation was conducted that considered the effects of pre-strain on the phase transformation. A continuous cooling transformation (CCT) diagram and a deformation continuous cooling transformation (DCCT) diagram were made in order to quantify the effect of the cooling rate and pre-strain on the phase transformation and hardness. The hardness was then calculated using the experimentally measured CCT and DCCT diagrams and the finite element analysis results. The calculated hardness was compared with the experimental hardness. Good agreement was found between the calculated and experimental results.

New method for springback compensation for the stamping of sheet metal components

NASA Astrophysics Data System (ADS)

Birkert, A.; Hartmann, B.; Straub, M.

2017-09-01

The need for car body structures of higher strength and at the same time lower weight results in serious challenges for the stamping process. Especially the use of high strength steel and aluminium sheets is causing growing problems with regard to elastic springback. To produce accurate parts the stamping dies must be adjusted more or less by the amount of the springback in the opposite direction. For this purpose well-known software solutions use the Displacement Adjustment Method or algorithms which are closely based on that method. A crucial issue of this method is that the generated die surfaces deviate from those of the target geometry with regard to surface area. A new Physical Compensation Method has been developed and validated which takes geometrical nonlinearity into account and creates compensated die geometries with equal-in-area die surfaces. In contrast to the standard mathematical/geometrical approach, the adjusted geometry is generated by a physical approach, which makes use of the virtual part stiffness. Hereby the target geometry is being deformed mechanically in a virtual process based on the springback simulation results by applying virtual forces in an additional elastic simulation. By doing so better part dimensions can be obtained in less tool optimization loops.

A sheet metal forming simulation of automotive outer panels considering the behavior of air in die cavity

NASA Astrophysics Data System (ADS)

Choi, Kwang Yong; Kim, Yun Chang; Choi, Hee Kwan; Kang, Chul Ho; Kim, Heon Young

2013-12-01

During a sheet metal forming process of automotive outer panels, the air trapped between a blank sheet and a die tool can become highly compressed, ultimately influencing the blank deformation and the press force. To prevent this problem, vent holes are drilled into die tools and needs several tens to hundreds according to the model size. The design and the drilling of vent holes are based on expert's experience and try-out result and thus the process can be one of reasons increasing development cycle. Therefore the study on the size, the number, and the position of vent holes is demanded for reducing development cycle, but there is no simulation technology for analyzing forming defects, making numerical sheet metal forming process simulations that incorporate the fluid dynamics of air. This study presents a sheet metal forming simulation of automotive outer panels (a roof and a body side outer) that simultaneously simulates the behavior of air in a die cavity. Through CAE results, the effect of air behavior and vent holes to blank deformation was analyzed. For this study, the commercial software PAM-STAMP{trade mark, serif} and PAM-SAFE{trade mark, serif} was used.

Silk Film Embossing System

NASA Astrophysics Data System (ADS)

Paquette, Mark S.

New tools are often required to facilitate new discoveries and test new methods. Commercial offerings can be prohibitively expensive and difficult to customize. The development of ad-hoc tools provides the most flexibility and provides an opportunity to modify and refine a technology. An embossing system was developed for silk film imprinting and stamping in order to facilitate and add versatility to the efforts involving micro- and nanoscale device manufacturing in biopolymers. This system features temperature controlled embossing surfaces, adjustable embossing pressures, and variable embossing times. The device can also be fitted with interchangeable temperature controlled embossing and stamping tools. The design, development, fabrication, applications, and future improvements are explored for the system. This device may facilitate new discoveries in the realm of biopolymer micro- and nanomanufacturing and may provide a path towards high volume production of silk film based technologies.

Modelling of stamping of DP steel automotive part accounting for the effect of hard components in the microstructure

NASA Astrophysics Data System (ADS)

Ambrozinski, Mateusz; Bzowski, Krzysztof; Mirek, Michal; Rauch, Lukasz; Pietrzyk, Maciej

2013-05-01

The paper presents simulations of the manufacturing of the automotive part, which has high influence on improvement of passengers safety. Two approaches to the Finite Element (FE) modelling of stamping of a part that provides extra stiffening of construction subassemblies in the back of a car were considered. The first is conventional simulation, which assumes that the material is a continuum with flow stress model and anisotropy coefficients determined from the tensile tests. In the second approach two-phase microstructure of the DP steel is accounted for in simulations. The FE2 method, which belongs to upscaling techniques, is used. Representative Volume Element (RVE), which is the basis of the upscaling approach and reflects the real microstructure, was obtained by the image analysis of the micrograph of the DP steel. However, since FE2 simulations with the real picture of the microstructure in the micro scale, are extremely time consuming, the idea of the Statistically Similar Representative Volume Element (SSRVE) was applied. SSRVE obtained for the DP steel, used for production of automotive part, is presented in the paper in the form of 3D inclusion. The macro scale model of the simulated part is described in details, as well as the results obtained for macro and micro-macro simulations.

Process Design of Aluminum Tailor Heat Treated Blanks.

PubMed

Kahrimanidis, Alexander; Lechner, Michael; Degner, Julia; Wortberg, Daniel; Merklein, Marion

2015-12-09

In many industrials field, especially in the automotive sector, there is a trend toward lightweight constructions in order to reduce the weight and thereby the CO₂ and NO x emissions of the products. An auspicious approach within this context is the substitution of conventional deep drawing steel by precipitation hardenable aluminum alloys. However, based on the low formability, the application for complex stamping parts is challenging. Therefore, at the Institute of Manufacturing Technology, an innovative technology to enhance the forming limit of these lightweight materials was invented. The key idea of the so-called Tailor Heat Treated Blanks (THTB) is optimization of the mechanical properties by local heat treatment before the forming operation. An accurate description of material properties is crucial to predict the forming behavior of tailor heat treated blanks by simulation. Therefore, within in this research project, a holistic approach for the design of the THTB process in dependency of the main influencing parameters is presented and discussed in detail. The capability of the approach for the process development of complex forming operations is demonstrated by a comparison of local blank thickness of a tailgate with the corresponding results from simulation.

Process Design of Aluminum Tailor Heat Treated Blanks

PubMed Central

Kahrimanidis, Alexander; Lechner, Michael; Degner, Julia; Wortberg, Daniel; Merklein, Marion

2015-01-01

In many industrials field, especially in the automotive sector, there is a trend toward lightweight constructions in order to reduce the weight and thereby the CO2 and NOx emissions of the products. An auspicious approach within this context is the substitution of conventional deep drawing steel by precipitation hardenable aluminum alloys. However, based on the low formability, the application for complex stamping parts is challenging. Therefore, at the Institute of Manufacturing Technology, an innovative technology to enhance the forming limit of these lightweight materials was invented. The key idea of the so-called Tailor Heat Treated Blanks (THTB) is optimization of the mechanical properties by local heat treatment before the forming operation. An accurate description of material properties is crucial to predict the forming behavior of tailor heat treated blanks by simulation. Therefore, within in this research project, a holistic approach for the design of the THTB process in dependency of the main influencing parameters is presented and discussed in detail. The capability of the approach for the process development of complex forming operations is demonstrated by a comparison of local blank thickness of a tailgate with the corresponding results from simulation. PMID:28793727

Investigations on the micro-scale surface interactions at the tool and workpiece interface in micro-manufacturing of bipolar plates for proton exchange membrane fuel cells

NASA Astrophysics Data System (ADS)

Peker, Mevlut Fatih

Micro-forming studies have been more attractive in recent years because of miniaturization trend. One of the promising metal forming processes, micro-stamping, provides durability, strength, surface finish, and low cost for metal products. Hence, it is considered a prominent method for fabricating bipolar plates (BPP) with micro-channel arrays on large metallic surfaces to be used in Proton Exchange Membrane Fuel Cells (PEMFC). Major concerns in micro-stamping of high volume BPPs are surface interactions between micro-stamping dies and blank metal plates, and tribological changes. These concerns play a critical role in determining the surface quality, channel formation, and dimensional precision of bipolar plates. The surface quality of BPP is highly dependent on the micro-stamping die surface, and process conditions due to large ratios of surface area to volume (size effect) that cause an increased level of friction and wear issues at the contact interface. Due to the high volume and fast production rates, BPP surface characteristics such as surface roughness, hardness, and stiffness may change because of repeated interactions between tool (micro-forming die) and workpiece (sheet blank of interest). Since the surface characteristics of BPPs have a strong effect on corrosion and contact resistance of bipolar plates, and consequently overall fuel cell performance, evolution of surface characteristics at the tool and workpiece should be monitored, controlled, and kept in acceptable ranges throughout the long production cycles to maintain the surface quality. Compared to macro-forming operations, tribological changes in micro-forming process are bigger challenges due to their dominance and criticality. Therefore, tribological size effect should be considered for better understanding of tribological changes in micro-scale. The integrity of process simulation to the experiments, on the other hand, is essential. This study describes an approach that aims to investigate the surface topography changes during long-run micro-stamping of BPPs, and establish relationships between surface roughness--corrosion resistance and surface roughness-contact resistance characteristics of BPPs. Formability levels of formed BPPs and repeatability characteristics of the process were investigated. In addition, blank thickness changes, von-Mises stress, plastic strain levels and distributions of micro-stamping process were determined via finite element analysis (FEA). Test results revealed that the surface roughness change for the stamping dies and BPPs was unsteady (no trend) due to the continuous change of surface topography (i.e. asperity deformation). Sub-micron range local plastic deformations on stamping dies led to surface topography changes on BPP in long-run manufacturing case. As surface defects trigger corrosion, the correlation between surface roughness and corrosion resistance of BPPs was found to be direct. Increasing number of surface irregularities (asperities) lowered contact surface area that resulted in increased contact resistance. ZrN coated BPPs, on the other hand, did not change surface roughness, however; it improved the protection of BPPs against corrosion significantly. In addition, ZrN coating increased the conductivity of BPPs and reduced the contact resistance between BPP and gas diffusion layer (GDL), at certain extent. As dimensional stability and repeatability was confirmed in forming of both uncoated and coated BPPs during the long run manufacturing, different formability levels were achieved for coated and uncoated samples. Lower channel height values were obtained for coated plates because of the different surface hardness of uncoated and coated plates. In tribological size effect part of study, micro stamping experiments using three different dies with distinct channel height values at different stamping force levels were performed. It was concluded that decrease in forming die dimensions led to increase in coefficient of friction as previously reported by other researchers as one of the consequences of tribological size effect. On the other hand, coefficient of friction values were not affected by the force levels used in the experiments and simulations, whereas plastic strain, equivalent stress, and formability levels were increased with increasing stamping force, as expected. In essence, this study proposed a methodology to investigate the long-run manufacturing effects on dimensional stability and surface characteristics of micro-stamped sheets. It also correlates these parameters to fuel cell performance measures such as interfacial contact and corrosion resistance.

Ultrathin high-resolution flexographic printing using nanoporous stamps

PubMed Central

Kim, Sanha; Sojoudi, Hossein; Zhao, Hangbo; Mariappan, Dhanushkodi; McKinley, Gareth H.; Gleason, Karen K.; Hart, A. John

2016-01-01

Since its invention in ancient times, relief printing, commonly called flexography, has been used to mass-produce artifacts ranging from decorative graphics to printed media. Now, higher-resolution flexography is essential to manufacturing low-cost, large-area printed electronics. However, because of contact-mediated liquid instabilities and spreading, the resolution of flexographic printing using elastomeric stamps is limited to tens of micrometers. We introduce engineered nanoporous microstructures, comprising polymer-coated aligned carbon nanotubes (CNTs), as a next-generation stamp material. We design and engineer the highly porous microstructures to be wetted by colloidal inks and to transfer a thin layer to a target substrate upon brief contact. We demonstrate printing of diverse micrometer-scale patterns of a variety of functional nanoparticle inks, including Ag, ZnO, WO3, and CdSe/ZnS, onto both rigid and compliant substrates. The printed patterns have highly uniform nanoscale thickness (5 to 50 nm) and match the stamp features with high fidelity (edge roughness, ~0.2 μm). We derive conditions for uniform printing based on nanoscale contact mechanics, characterize printed Ag lines and transparent conductors, and achieve continuous printing at a speed of 0.2 m/s. The latter represents a combination of resolution and throughput that far surpasses industrial printing technologies. PMID:27957542

26 CFR 1.451-4 - Accounting for redemption of trading stamps and coupons.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 1971, its first year of operation, X sells 10 million stamps at $5 per 1,000; it redeems 3 million... trading stamps as follows: Gross receipts from sales (10 million stamps at $5 per 1,000) $50,000 Less... income from sales of stamps 23,000 (b) In 1972, X also sells 10 million stamps at $5 per 1,000 stamps...

A Fully Integrated Humidity Sensor System-on-Chip Fabricated by Micro-Stamping Technology

PubMed Central

Huang, Che-Wei; Huang, Yu-Jie; Lu, Shey-Shi; Lin, Chih-Ting

2012-01-01

A fully integrated humidity sensor chip was designed, implemented, and tested. Utilizing the micro-stamping technology, the pseudo-3D sensor system-on-chip (SSoC) architecture can be implemented by stacking sensing materials directly on the top of a CMOS-fabricated chip. The fabricated sensor system-on-chip (2.28 mm × 2.48 mm) integrated a humidity sensor, an interface circuit, a digital controller, and an On-Off Keying (OOK) wireless transceiver. With low power consumption, i.e., 750 μW without RF operation, the sensitivity of developed sensor chip was experimentally verified in the relative humidity (RH) range from 32% to 60%. The response time of the chip was also experimentally verified to be within 5 seconds from RH 36% to RH 64%. As a consequence, the implemented humidity SSoC paves the way toward the an ultra-small sensor system for various applications.

Evaluation of anti-sticking layers performances for 200mm wafer scale Smart NILTM process through surface and defectivity characterizations

NASA Astrophysics Data System (ADS)

Delachat, F.; Phillipe, J.-C.; Larrey, V.; Fournel, F.; Bos, S.; Teyssèdre, H.; Chevalier, Xavier; Nicolet, Célia; Navarro, Christophe; Cayrefourcq, Ian

2018-03-01

In this work, an evaluation of various ASL processes for 200 mm wafer scale in the HERCULES® NIL equipment platform available at the CEA-Leti through the INSPIRE program is reported. The surface and adherence energies were correlated to the AFM and defectivity results in order to select the most promising ASL process for high resolution etch mask applications. The ASL performances of the selected process were evaluated by multiple working stamp fabrication using unpatterned and patterned masters though defectivity monitoring on optical based-inspection tools. Optical and SEM defect reviews were systematically performed. Multiple working stamps fabrication without degradation of the master defectivity was witnessed. This evaluation enabled to benchmark several ASL solutions based on the grafted technology develop by ARKEMA in order to reduce and optimize the soft stamp defectivity prior to its replication and therefore considerably reduce the final imprint defectivity for the Smart NIL process.

78 FR 10201 - Proposed Information Collection; Electronic Duck Stamp Program

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-13

...-FF09M13100] Proposed Information Collection; Electronic Duck Stamp Program AGENCY: Fish and Wildlife Service... and conservation stamp (Federal Duck Stamp) annually. The stamps are a vital tool for wetland conservation. Ninety-eight cents out of every dollar generated by the sale of Federal Duck Stamps goes directly...

Stamping an AA5754 Train Window Panel with High Dent Resistance Using Locally Annealed Blanks

NASA Astrophysics Data System (ADS)

Piccininni, A.; Guglielmi, P.; Lo Franco, A.; Palumbo, G.

2017-09-01

The warm stamping of an AA5754-H32 window panel for railway vehicles applications has been proposed in the present work. The adoption of increased working temperatures can be surely considered the most effective solution for this alloy to overcome the limited material formability at room temperature [Palumbo et al. “Warm Forming of an AA5754 Component for Railway Vehicle Applications”, Procedia Engineering, Vol. 183, 2017, Pages 351-356] but, in order to improve the overall dent resistance of the component, the initial wrought conditions have been chosen in the present work. The manufacturing of the window panel was thus subdivided into a preliminary local heat treatment (assumed to be performed by laser) to anneal the material and a subsequent warm stamping step using heated tools. The best combination of temperature and holding time able to produce the annealing of the investigated alloy was determined using the physical simulator Gleeble 3180. On the contrary, the warm forming step was designed by means of thermo-mechanical simulations: in order to model the AA5754-H32 blank with annealed regions, an extensive experimental campaign (tensile and formability tests) was conducted using specimens in the annealed (H111) and in the wrought (H32) conditions. Through the numerical approach it was thus possible define: (i) the extent of the annealed regions; (ii) the punch speed to get a sound component.

STS-8 postal Stamp envelope

NASA Technical Reports Server (NTRS)

1983-01-01

STS-8 postal Stamp envelope with Challenger insignia, USA eagle stamp, 25th NASA anniversary stamp. The envelope is stamped with various postmarks, one saying Kennedy Space Center, Fl., another saying 'Returned to earth, Edwards AFB, CA'.

Automotive Manufacturing Processes. Volume IV - Metal Stamping and Plastic Forming Processes

DOT National Transportation Integrated Search

1981-02-01

Extensive material substitution and resizing of the domestic automotive fleet, as well as the introduction of new technologies, will require major changes in the techniques and equipment used in the various manufacturing processes employed in the pro...

Usage and Recall of the Food Stamp Office Resource Kit (FSORK) by Food Stamp Applicants in 4 California Counties

ERIC Educational Resources Information Center

Ghirardelli, Alyssa; Linares, Amanda; Fong, Amy

2011-01-01

Objective: To evaluate recall and usage of the Food Stamp Office Resource Kit (FSORK), a set of nutrition education materials designed for use in food stamp offices. Design: Client intercept exit surveys, an environmental scan, and individual observations of clients in the food stamp office. Setting: Four food stamp offices in California.…

Impact Of The Material Variability On The Stamping Process: Numerical And Analytical Analysis

NASA Astrophysics Data System (ADS)

Ledoux, Yann; Sergent, Alain; Arrieux, Robert

2007-05-01

The finite element simulation is a very useful tool in the deep drawing industry. It is used more particularly for the development and the validation of new stamping tools. It allows to decrease cost and time for the tooling design and set up. But one of the most important difficulties to have a good agreement between the simulation and the real process comes from the definition of the numerical conditions (mesh, punch travel speed, limit conditions,…) and the parameters which model the material behavior. Indeed, in press shop, when the sheet set changes, often a variation of the formed part geometry is observed according to the variability of the material properties between these different sets. This last parameter represents probably one of the main source of process deviation when the process is set up. That's why it is important to study the influence of material data variation on the geometry of a classical stamped part. The chosen geometry is an omega shaped part because of its simplicity and it is representative one in the automotive industry (car body reinforcement). Moreover, it shows important springback deviations. An isotropic behaviour law is assumed. The impact of the statistical deviation of the three law coefficients characterizing the material and the friction coefficient around their nominal values is tested. A Gaussian distribution is supposed and their impact on the geometry variation is studied by FE simulation. An other approach is envisaged consisting in modeling the process variability by a mathematical model and then, in function of the input parameters variability, it is proposed to define an analytical model which leads to find the part geometry variability around the nominal shape. These two approaches allow to predict the process capability as a function of the material parameter variability.

Using Micro-Molding and Stamping to Fabricate Conductive Polydimethylsiloxane-Based Flexible High-Sensitivity Strain Gauges.

PubMed

Han, Chi-Jui; Chiang, Hsuan-Ping; Cheng, Yun-Chien

2018-02-18

In this study, polydimethylsiloxane (PDMS) and conductive carbon nanoparticles were combined to fabricate a conductive elastomer PDMS (CPDMS). A high sensitive and flexible CPDMS strain sensor is fabricated by using stamping-process based micro patterning. Compared with conventional sensors, flexible strain sensors are more suitable for medical applications but are usually fabricated by photolithography, which suffers from a large number of steps and difficult mass production. Hence, we fabricated flexible strain sensors using a stamping-process with fewer processes than photolithography. The piezoresistive coefficient and sensitivity of the flexible strain sensor were improved by sensor pattern design and thickness change. Micro-patterning is used to fabricate various CPDMS microstructure patterns. The effect of gauge pattern was evaluated with ANSYS simulations. The piezoresistance of the strain gauges was measured and the gauge factor determined. Experimental results show that the piezoresistive coefficient of CPDMS is approximately linear. Gauge factor measurement results show that the gauge factor of a 140.0 μm thick strain gauge with five grids is the highest.

Information Technology Progress in North Korea and Its Prospects

DTIC Science & Technology

2005-08-01

North Korean company agreed to develop a Korean- Chinese language-interpretation software together with a South Korean company, L&I Soft. The North...Chosun cuisine , and Chosun stamps. Furthermore, governmental agencies and university research institutes developed roughly 10 programs for the Science

Surrogate models for sheet metal stamping problem based on the combination of proper orthogonal decomposition and radial basis function

NASA Astrophysics Data System (ADS)

Dang, Van Tuan; Lafon, Pascal; Labergere, Carl

2017-10-01

In this work, a combination of Proper Orthogonal Decomposition (POD) and Radial Basis Function (RBF) is proposed to build a surrogate model based on the Benchmark Springback 3D bending from the Numisheet2011 congress. The influence of the two design parameters, the geometrical parameter of the die radius and the process parameter of the blank holder force, on the springback of the sheet after a stamping operation is analyzed. The classical Design of Experience (DoE) uses Full Factorial to design the parameter space with sample points as input data for finite element method (FEM) numerical simulation of the sheet metal stamping process. The basic idea is to consider the design parameters as additional dimensions for the solution of the displacement fields. The order of the resultant high-fidelity model is reduced through the use of POD method which performs model space reduction and results in the basis functions of the low order model. Specifically, the snapshot method is used in our work, in which the basis functions is derived from snapshot deviation of the matrix of the final displacements fields of the FEM numerical simulation. The obtained basis functions are then used to determine the POD coefficients and RBF is used for the interpolation of these POD coefficients over the parameter space. Finally, the presented POD-RBF approach which is used for shape optimization can be performed with high accuracy.

Use of tobacco tax stamps to prevent and reduce illicit tobacco trade--United States, 2014.

PubMed

Chriqui, Jamie; DeLong, Hillary; Gourdet, Camille; Chaloupka, Frank; Edwards, Sarah Matthes; Xu, Xin; Promoff, Gabbi

2015-05-29

Tobacco use is the leading cause of preventable disease and death in the United States. Increasing the unit price on tobacco products is the most effective tobacco prevention and control measure. Illicit tobacco trade (illicit trade) undermines high tobacco prices by providing tobacco users with cheaper-priced alternatives. In the United States, illicit trade primarily occurs when cigarettes are bought from states, jurisdictions, and federal reservation land with lower or no excise taxes, and sold in jurisdictions with higher taxes. Applying tax stamps to tobacco products, which provides documentation that taxes have been paid, is an important tool to combat illicit trade. Comprehensive tax stamping policy, which includes using digital, encrypted ("high-tech") stamps, applying stamps to all tobacco products, and working with tribes on stamping agreements, can further prevent and reduce illicit trade. This report describes state laws governing tax stamps on cigarettes, little cigars (cigarette-sized cigars), roll-your-own tobacco (RYOT), and tribal tobacco sales across the United States as of January 1, 2014, and assesses the extent of comprehensive tobacco tax stamping in the United States. Forty-four states (including the District of Columbia [DC]) applied traditional paper ("low-tech") tax stamps to cigarettes, whereas four authorized more effective high-tech stamps. Six states explicitly required stamps on other tobacco products (i.e., tobacco products other than cigarettes), and in approximately one third of states with tribal lands, tribes required tax stamping to address illicit purchases by nonmembers. No U.S. state had a comprehensive approach to tobacco tax stamping. Enhancing tobacco tax stamping across the country might further prevent and reduce illicit trade in the United States.

46 CFR 53.10-10 - Certification by stamping.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Certification by stamping. 53.10-10 Section 53.10-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING HEATING BOILERS Tests, Inspection, Stamping, and Reporting (Article 5) § 53.10-10 Certification by stamping. Stamping of heating boilers shall be as indicated in HG-53...

46 CFR 53.10-10 - Certification by stamping.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Certification by stamping. 53.10-10 Section 53.10-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING HEATING BOILERS Tests, Inspection, Stamping, and Reporting (Article 5) § 53.10-10 Certification by stamping. Stamping of heating boilers shall be as indicated in HG-53...

46 CFR 53.10-10 - Certification by stamping.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Certification by stamping. 53.10-10 Section 53.10-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING HEATING BOILERS Tests, Inspection, Stamping, and Reporting (Article 5) § 53.10-10 Certification by stamping. Stamping of heating boilers shall be as indicated in HG-53...

46 CFR 53.10-10 - Certification by stamping.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Certification by stamping. 53.10-10 Section 53.10-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING HEATING BOILERS Tests, Inspection, Stamping, and Reporting (Article 5) § 53.10-10 Certification by stamping. Stamping of heating boilers shall be as indicated in HG-53...

46 CFR 53.10-10 - Certification by stamping.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Certification by stamping. 53.10-10 Section 53.10-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING HEATING BOILERS Tests, Inspection, Stamping, and Reporting (Article 5) § 53.10-10 Certification by stamping. Stamping of heating boilers shall be as indicated in HG-53...

Minerals on postage stamps: A mix of art, history, economics and geography

NASA Astrophysics Data System (ADS)

Glover, Paul

2010-05-01

Most people would agree that minerals represent some of the most beautiful natural objects known to mankind, especially in the form of precious and semi-precious gemstones. It is hardly surprising, therefore, that they are often illustrated on stamps. Examples are the fine crystalline forms represented as coloured etchings in the French 1986 issue, and the stylized simplicity of the mineral stamps that were part of the Swiss Pro Patria series, issued annually between 1958 and 1961. I aim in this presentation to introduce the beautiful world of mineral illustrations on stamps. The talk cannot be comprehensive because of the very large number of minerals and stamps concerned, but it will introduce the range of minerals depicted on stamps, then look in some greater detail at several sets from France, Southern Africa and East Germany. Minerals become the subject of sets of stamps for many reasons. In many cases, it is part of an attempt by the particular national post office to depict the whole of the natural history of their country in stamp form - a statement of nationality and politics. The 1986 French issue was an example which followed sets of stamps that had already portrayed insects, flowers, trees and birds native to France. We also find that certain countries have produced several sets of stamps to mark the importance to their economy of mining particular minerals. Many African states depend upon minerals for much of their wealth and economic power, explaining why, for instance, Sierra Leone issued over 35 stamps on the subject of diamonds between 1965 and 1978, and why over 77% of mineral stamps come from countries with major mining interests. Countries with traditional links with the history of the study of geology and mining also produce mineral stamps. These are usually European countries with a long record of the study of the Earth, such as Germany and Switzerland. Curiously enough, though, despite its fine tradition of geological observation and research, the United Kingdom has never produced a stamp depicting rocks or minerals. It is often said that the study of stamps is a study of history, language, culture, art, geography and politics. If this is true for stamps in general, it is particularly true for minerals on stamps.

Computer-aided communication satellite system analysis and optimization

NASA Technical Reports Server (NTRS)

Stagl, T. W.; Morgan, N. H.; Morley, R. E.; Singh, J. P.

1973-01-01

The capabilities and limitations of the various published computer programs for fixed/broadcast communication satellite system synthesis and optimization are discussed. A satellite Telecommunication analysis and Modeling Program (STAMP) for costing and sensitivity analysis work in application of communication satellites to educational development is given. The modifications made to STAMP include: extension of the six beam capability to eight; addition of generation of multiple beams from a single reflector system with an array of feeds; an improved system costing to reflect the time value of money, growth in earth terminal population with time, and to account for various measures of system reliability; inclusion of a model for scintillation at microwave frequencies in the communication link loss model; and, an updated technological environment.

Time series analysis of tool wear in sheet metal stamping using acoustic emission

NASA Astrophysics Data System (ADS)

Vignesh Shanbhag, V.; Pereira, P. Michael; Rolfe, F. Bernard; Arunachalam, N.

2017-09-01

Galling is an adhesive wear mode that often affects the lifespan of stamping tools. Since stamping tools represent significant economic cost, even a slight improvement in maintenance cost is of high importance for the stamping industry. In other manufacturing industries, online tool condition monitoring has been used to prevent tool wear-related failure. However, monitoring the acoustic emission signal from a stamping process is a non-trivial task since the acoustic emission signal is non-stationary and non-transient. There have been numerous studies examining acoustic emissions in sheet metal stamping. However, very few have focused in detail on how the signals change as wear on the tool surface progresses prior to failure. In this study, time domain analysis was applied to the acoustic emission signals to extract features related to tool wear. To understand the wear progression, accelerated stamping tests were performed using a semi-industrial stamping setup which can perform clamping, piercing, stamping in a single cycle. The time domain features related to stamping were computed for the acoustic emissions signal of each part. The sidewalls of the stamped parts were scanned using an optical profilometer to obtain profiles of the worn part, and they were qualitatively correlated to that of the acoustic emissions signal. Based on the wear behaviour, the wear data can be divided into three stages: - In the first stage, no wear is observed, in the second stage, adhesive wear is likely to occur, and in the third stage severe abrasive plus adhesive wear is likely to occur. Scanning electron microscopy showed the formation of lumps on the stamping tool, which represents galling behavior. Correlation between the time domain features of the acoustic emissions signal and the wear progression identified in this study lays the basis for tool diagnostics in stamping industry.

Technology Security Policy: From the Cold War to the New World Order

DTIC Science & Technology

1993-12-01

of Counterproliferation Initiative Legislation. The House DoD Authorization bill essentially rubber -stamps the Administration’s budget request for...Sciences Naval Postgraduate School Monterey, California 93943-5103 5. Richard Ellings I NBR 715 SAFECO Plaza Seattle, Washington 98185 6. LT Dolores M

Monitoring gait in multiple sclerosis with novel wearable motion sensors.

PubMed

Moon, Yaejin; McGinnis, Ryan S; Seagers, Kirsten; Motl, Robert W; Sheth, Nirav; Wright, John A; Ghaffari, Roozbeh; Sosnoff, Jacob J

2017-01-01

Mobility impairment is common in people with multiple sclerosis (PwMS) and there is a need to assess mobility in remote settings. Here, we apply a novel wireless, skin-mounted, and conformal inertial sensor (BioStampRC, MC10 Inc.) to examine gait characteristics of PwMS under controlled conditions. We determine the accuracy and precision of BioStampRC in measuring gait kinematics by comparing to contemporary research-grade measurement devices. A total of 45 PwMS, who presented with diverse walking impairment (Mild MS = 15, Moderate MS = 15, Severe MS = 15), and 15 healthy control subjects participated in the study. Participants completed a series of clinical walking tests. During the tests participants were instrumented with BioStampRC and MTx (Xsens, Inc.) sensors on their shanks, as well as an activity monitor GT3X (Actigraph, Inc.) on their non-dominant hip. Shank angular velocity was simultaneously measured with the inertial sensors. Step number and temporal gait parameters were calculated from the data recorded by each sensor. Visual inspection and the MTx served as the reference standards for computing the step number and temporal parameters, respectively. Accuracy (error) and precision (variance of error) was assessed based on absolute and relative metrics. Temporal parameters were compared across groups using ANOVA. Mean accuracy±precision for the BioStampRC was 2±2 steps error for step number, 6±9ms error for stride time and 6±7ms error for step time (0.6-2.6% relative error). Swing time had the least accuracy±precision (25±19ms error, 5±4% relative error) among the parameters. GT3X had the least accuracy±precision (8±14% relative error) in step number estimate among the devices. Both MTx and BioStampRC detected significantly distinct gait characteristics between PwMS with different disability levels (p<0.01). BioStampRC sensors accurately and precisely measure gait parameters in PwMS across diverse walking impairment levels and detected differences in gait characteristics by disability level in PwMS. This technology has the potential to provide granular monitoring of gait both inside and outside the clinic.

44. INTERIOR VIEW LOOKING NORTH NORTHWEST BEHIND THE STAMP BATTERIES. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

44. INTERIOR VIEW LOOKING NORTH NORTHWEST BEHIND THE STAMP BATTERIES. THIS IS A CLOSE UP VIEW OF THE STAMP SHAFTS WITH THE TAPPETS AND WOODEN STOPS THAT WERE USED TO PLACE THE STAMPS IN AN UP POSITION TO CLEAN OR REPLACE THE STAMP SHOES IN THE MORTAR BOX. - Standard Gold Mill, East of Bodie Creek, Northeast of Bodie, Bodie, Mono County, CA

Limited indications of tax stamp discordance and counterfeiting on cigarette packs purchased in tobacco retailers, 97 counties, USA, 2012.

PubMed

Lee, Joseph G L; Golden, Shelley D; Ribisl, Kurt M

2017-12-01

Increasing the per-unit cost of tobacco products is one of the strongest interventions for tobacco control. In jurisdictions with higher taxes in the U.S., however, cigarette pack litter studies show a substantial proportion of littered packs lack the appropriate tax stamp. More limited but still present counterfeiting also exists. We sought to examine the role of tobacco retailers as a source for untaxed and counterfeit products. Data collectors purchased Newport Green (menthol) or Marlboro Red cigarette packs in a national probability-based sample of tobacco retailers (in 97 counties) from June-October 2012. They made no effort to buy counterfeit or untaxed cigarettes. In this cross-sectional study, we assessed the presence, tax authority, and type (low-tech thermal vs. encrypted) of cigarette pack tax stamps; concordance of tax stamps with where the pack was purchased; and, for Marlboro cigarettes, publicly available visible indicators of counterfeiting. We purchased 2147 packs of which 2033 had tax stamps. Packs missing stamps were in states that do not require them. We found very limited discordance between store location and tax stamp(s) (< 1%). However, a substantial minority of cigarette packs had damaged tax stamps (13%). This occurred entirely with low-tech tax stamps and was not identified with encrypted tax stamps. We found no clear evidence of counterfeit products. Almost all tax stamps matched the location of purchase. Litter studies may be picking up legal tax avoidance instead of illegal tax evasion or, alternatively, purchase of illicit products requires special request by the purchaser.

Odontophilately: dentistry on stamps.

PubMed

Drinnan, Alan J

2004-11-01

The collecting of stamps can be a rewarding exercise and may be as intense or as superficial as one would wish. Some collectors concentrate on the technical aspects of stamp production, whereas others concentrate on the details of their issue by the postal authorities. Others collect stamps with the view to buying and selling them for financial gain. Some are more interested in the "social" aspects of a stamp (e.g., facts about the country issuing it, location of the country, population, government structure, main industries, place of dentistry within the society). A collection of topical stamps on odontophilately with the details of those types listed above should stimulate anyone with the imagination to appreciate the wide and sometimes romantic stories behind every stamp.

STAMP2 increases oxidative stress and is critical for prostate cancer

PubMed Central

Jin, Yang; Wang, Ling; Qu, Su; Sheng, Xia; Kristian, Alexandr; Mælandsmo, Gunhild M; Pällmann, Nora; Yuca, Erkan; Tekedereli, Ibrahim; Gorgulu, Kivanc; Alpay, Neslihan; Sood, Anil; Lopez-Berestein, Gabriel; Fazli, Ladan; Rennie, Paul; Risberg, Bjørn; Wæhre, Håkon; Danielsen, Håvard E; Ozpolat, Bulent; Saatcioglu, Fahri

2015-01-01

The six transmembrane protein of prostate 2 (STAMP2) is an androgen-regulated gene whose mRNA expression is increased in prostate cancer (PCa). Here, we show that STAMP2 protein expression is increased in human PCa compared with benign prostate that is also correlated with tumor grade and treatment response. We also show that STAMP2 significantly increased reactive oxygen species (ROS) in PCa cells through its iron reductase activity which also depleted NADPH levels. Knockdown of STAMP2 expression in PCa cells inhibited proliferation, colony formation, and anchorage-independent growth, and significantly increased apoptosis. Furthermore, STAMP2 effects were, at least in part, mediated by activating transcription factor 4 (ATF4), whose expression is regulated by ROS. Consistent with in vitro findings, silencing STAMP2 significantly inhibited PCa xenograft growth in mice. Finally, therapeutic silencing of STAMP2 by systemically administered nanoliposomal siRNA profoundly inhibited tumor growth in two established preclinical PCa models in mice. These data suggest that STAMP2 is required for PCa progression and thus may serve as a novel therapeutic target. PMID:25680860

Application of shell elements in simulation of cans ironing

NASA Astrophysics Data System (ADS)

Andrianov, A. V.; Erisov, Y. A.; Aryshensky, E. V.; Aryshensky, V. Y.

2017-01-01

In the present study, the special shell finite elements are used to simulate the drawing with high ironing ratio of aluminum beverage cans. These elements are implemented in commercial software complex PAM-STAMP 2G by means of T.T.S. normal stress option, which is used for ironing to describe well normal stress. By comparison of simulation and experimental data, it is shown that shell elements with T.T.S. option are capable to provide accurate simulation of deep drawing and ironing. The error of can thickness and height computation agrees with the engineering computation accuracy.

Rapid thermal processing by stamping

DOEpatents

Stradins, Pauls; Wang, Qi

2013-03-05

A rapid thermal processing device and methods are provided for thermal processing of samples such as semiconductor wafers. The device has components including a stamp (35) having a stamping surface and a heater or cooler (40) to bring it to a selected processing temperature, a sample holder (20) for holding a sample (10) in position for intimate contact with the stamping surface; and positioning components (25) for moving the stamping surface and the stamp (35) in and away from intimate, substantially non-pressured contact. Methods for using and making such devices are also provided. These devices and methods allow inexpensive, efficient, easily controllable thermal processing.

Imrovement of the cold forming technology of the parts such as longeron

NASA Astrophysics Data System (ADS)

Kashapova, L. R.; Pankratov, D. L.; Bilyalova, A. A.

2014-12-01

As a result of modeling in LS-PREPOST preprocessor of the program LS-DYNA a range of radii of curvature edge transition matrix (27,5 ° <= R <= 48 °) is obtained, which allows to produce defect-free stamping slots for longeron shock absorbers of tractors KAMAZ-5460.

Studies on the finite element simulation in sheet metal stamping processes

NASA Astrophysics Data System (ADS)

Huang, Ying

The sheet metal stamping process plays an important role in modern industry. With the ever-increasing demand for shape complexity, product quality and new materials, the traditional trial and error method for setting up a sheet metal stamping process is no longer efficient. As a result, the Finite Element Modeling (FEM) method has now been widely used. From a physical point of view, the formability and the quality of a product are influenced by several factors. The design of the product in the initial stage and the motion of the press during the production stage are two of these crucial factors. This thesis focuses on the numerical simulation for these two factors using FEM. Currently, there are a number of commercial FEM software systems available in the market. These software systems are based on an incremental FEM process that models the sheet metal stamping process in small incremental steps. Even though the incremental FEM is accurate, it is not suitable for the initial conceptual design for its needing of detailed design parameters and enormous calculation times. As a result, another type of FEM, called the inverse FEM method or one-step FEM method, has been proposed. While it is less accurate than that of the incremental method, this method requires much less computation and hence, has a great potential. However, it also faces a number of unsolved problems, which limits its application. This motivates the presented research. After the review of the basic theory of the inverse method, a new modified arc-length search method is proposed to find better initial solution. The methods to deal with the vertical walls are also discussed and presented. Then, a generalized multi-step inverse FEM method is proposed. It solves two key obstacles: the first one is to determine the initial solution of the intermediate three-dimensional configurations and the other is to control the movement of nodes so they could only slide on constraint surfaces during the search by Newton-Raphson iteration. The computer implementation of the generalized multi-step inverse FEM is also presented. By comparing to the simulation results using a commercial software system, the effectiveness of the new method is validated. Other than the product design, the punch motion (including punch speed and punch trajectory) of the stamping press also has significant effect on the formability and the quality of the product. In fact, this is one of the major reasons why hydraulic presses and/or servo presses are used for parts which demand high quality. In order to reveal the quantitative correlation between the punch motion and the part quality, the Cowper-Symonds strain rate constitutive model and the implicit dynamic incremental FEM are combined to conduct the research. The effects of the punch motion on the part quality, especially the plastic strain distribution and the potential springback, have been investigated for the deep drawing and the bending processes respectively. A qualitative relationship between the punch motion and the part quality is also derived. The reaction force of the punch motion causes the dynamic deformation of the press during the stamping, which in turn influences the part quality as well. This dynamic information, in the form of the strain signal, is an important basis for the on-line monitoring of the part quality. By using the actual force as the input to the press, the incremental FEM is needed to predict the strain of the press. The result is validated by means of experiments and can be used to assist the on-line monitoring.

Proceedings of the Acquisition Research Symposium: Acquisition for the Future, Imagination, Innovation, and Implementation, 1991. Volume 2.

DTIC Science & Technology

1991-01-01

Estimates, in support force structure, and identifying of cost- effectiveness studies , other system characteristics. system analysis efforts, and trade- A...mission effectiveness studies , used to justify technology evaluate the results in terms funding. These technology of benefit vs. cost, and marketers often...the formal studies serve on mission effectiveness and to rubber stamp these prede- ultimately, benefit vs. cost termined solutions. In an 101 attempt to

42 CFR 71.3 - Designation of yellow fever vaccination centers; Validation stamps.

Code of Federal Regulations, 2012 CFR

2012-10-01

...; Validation stamps. 71.3 Section 71.3 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN... Designation of yellow fever vaccination centers; Validation stamps. (a) Designation of yellow fever... health department, may revoke designation. (b) Validation stamps. International Certificates of...

42 CFR 71.3 - Designation of yellow fever vaccination centers; Validation stamps.

Code of Federal Regulations, 2014 CFR

2014-10-01

...; Validation stamps. 71.3 Section 71.3 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN... Designation of yellow fever vaccination centers; Validation stamps. (a) Designation of yellow fever... health department, may revoke designation. (b) Validation stamps. International Certificates of...

42 CFR 71.3 - Designation of yellow fever vaccination centers; Validation stamps.

Code of Federal Regulations, 2011 CFR

2011-10-01

...; Validation stamps. 71.3 Section 71.3 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN... Designation of yellow fever vaccination centers; Validation stamps. (a) Designation of yellow fever... health department, may revoke designation. (b) Validation stamps. International Certificates of...

42 CFR 71.3 - Designation of yellow fever vaccination centers; Validation stamps.

Code of Federal Regulations, 2013 CFR

2013-10-01

...; Validation stamps. 71.3 Section 71.3 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN... Designation of yellow fever vaccination centers; Validation stamps. (a) Designation of yellow fever... health department, may revoke designation. (b) Validation stamps. International Certificates of...

DC-STAMP Is an Osteoclast Fusogen Engaged in Periodontal Bone Resorption

PubMed Central

Wisitrasameewong, W.; Kajiya, M.; Movila, A.; Rittling, S.; Ishii, T.; Suzuki, M.; Matsuda, S.; Mazda, Y.; Torruella, M.R.; Azuma, M.M.; Egashira, K.; Freire, M.O.; Sasaki, H.; Wang, C.Y.; Han, X.; Taubman, M.A.; Kawai, T.

2017-01-01

Dendritic cell-specific transmembrane protein (DC-STAMP) plays a key role in the induction of osteoclast (OC) cell fusion, as well as DC-mediated immune regulation. While DC-STAMP gene expression is upregulated in the gingival tissue with periodontitis, its pathophysiological roles in periodontitis remain unclear. To evaluate the effects of DC-STAMP in periodontitis, anti-DC-STAMP–monoclonal antibody (mAb) was tested in a mouse model of ligature-induced periodontitis (n = 6–7/group) where Pasteurella pneumotropica (Pp)-reactive immune response activated T cells to produce receptor activator of nuclear factor kappa-B ligand (RANKL), which, in turn, promotes the periodontal bone loss via upregulation of osteoclastogenesis. DC-STAMP was expressed on the cell surface of mature multinuclear OCs, as well as immature mononuclear OCs, in primary cultures of RANKL-stimulated bone marrow cells. Anti-DC-STAMP-mAb suppressed the emergence of large, but not small, multinuclear OCs, suggesting that DC-STAMP is engaged in the late stage of cell fusion. Anti-DC-STAMP-mAb also inhibited pit formation caused by RANKL-stimulated bone marrow cells. Attachment of ligature to a second maxillary molar induced DC-STAMP messenger RNA and protein, along with elevated tartrate-resistant acid phosphatase–positive (TRAP+) OCs and alveolar bone loss. As we expected, systemic administration of anti-DC-STAMP-mAb downregulated the ligature-induced alveolar bone loss. Importantly, local injection of anti-DC-STAMP-mAb also suppressed alveolar bone loss and reduced the total number of multinucleated TRAP+ cells in mice that received ligature attachment. Attachment of ligature induced significantly elevated tumor necrosis factor–α, interleukin-1β, and RANKL in the gingival tissue compared with the control site without ligature (P < 0.05), which was unaffected by local injection with either anti-DC-STAMP-mAb or control-mAb. Neither in vivo anti-Pp IgG antibody nor in vitro anti-Pp T-cell response and resultant production of RANKL was affected by anti-DC-STAMP-mAb. This study illustrated the roles of DC-STAMP in promoting local OC cell fusion without affecting adaptive immune responses to oral bacteria. Therefore, it is plausible that a novel therapeutic regimen targeting DC-STAMP could suppress periodontal bone loss. PMID:28199142

Selecting Magnet Laminations Recipes Using the Meth-od of Sim-u-la-ted Annealing

NASA Astrophysics Data System (ADS)

Russell, A. D.; Baiod, R.; Brown, B. C.; Harding, D. J.; Martin, P. S.

1997-05-01

The Fermilab Main Injector project is building 344 dipoles using more than 7000 tons of steel. Budget and logistical constraints required that steel production, lamination stamping and magnet fabrication proceed in parallel. There were significant run-to-run variations in the magnetic properties of the steel (Martin, P.S., et al., Variations in the Steel Properties and the Excitation Characteristics of FMI Dipoles, this conference). The large lamination size (>0.5 m coil opening) resulted in variations of gap height due to differences in stress relief in the steel after stamping. To minimize magnet-to-magnet strength and field shape variations the laminations were shuffled based on the available magnetic and mechanical data and assigned to magnets using a computer program based on the method of simulated annealing. The lamination sets selected by the program have produced magnets which easily satisfy the design requirements. Variations of the average magnet gap are an order of magnitude smaller than the variations in lamination gaps. This paper discusses observed gap variations, the program structure and the strength uniformity results.

Defect detection and classification of galvanized stamping parts based on fully convolution neural network

NASA Astrophysics Data System (ADS)

Xiao, Zhitao; Leng, Yanyi; Geng, Lei; Xi, Jiangtao

2018-04-01

In this paper, a new convolution neural network method is proposed for the inspection and classification of galvanized stamping parts. Firstly, all workpieces are divided into normal and defective by image processing, and then the defective workpieces extracted from the region of interest (ROI) area are input to the trained fully convolutional networks (FCN). The network utilizes an end-to-end and pixel-to-pixel training convolution network that is currently the most advanced technology in semantic segmentation, predicts result of each pixel. Secondly, we mark the different pixel values of the workpiece, defect and background for the training image, and use the pixel value and the number of pixels to realize the recognition of the defects of the output picture. Finally, the defect area's threshold depended on the needs of the project is set to achieve the specific classification of the workpiece. The experiment results show that the proposed method can successfully achieve defect detection and classification of galvanized stamping parts under ordinary camera and illumination conditions, and its accuracy can reach 99.6%. Moreover, it overcomes the problem of complex image preprocessing and difficult feature extraction and performs better adaptability.

Mathematical Modeling of Hydroelastic Oscillations of the Stamp and the Plate, Resting on Pasternak Foundation

NASA Astrophysics Data System (ADS)

Mogilevich, L. I.; Popov, V. S.; Popova, A. A.; Christoforova, A. V.

2018-01-01

The forced oscillations of the elastic fixed stamp and the plate, resting on Pasternak foundation are studied. The oscillations are caused by pressure pulsation in liquid layer between the stamp and the plate. Pasternak model is chosen as an elastic foundation. The laws of the stamp movement, the plate deflection and pressure in the liquid are discovered on the basis of hydroelasticity problem analytical solution. The functions of amplitude deflection distribution and liquid pressure along the plate are constructed, as well as the stamp amplitude-frequency characteristic. The obtained mathematical model allows to investigate the dynamics of hydroelastic interaction of the stamp with the plate, resting on elastic foundation, to define resonance frequencies of the plate and the stamp and corresponding deflections amplitudes, as well as liquid presser amplitudes.

Influence of temperature and friction on the 22MnB5 formability under hot stamping conditions

NASA Astrophysics Data System (ADS)

Venturato, G.; Ghiotti, A.; Bruschi, S.

2018-05-01

The need to increase the safety and decrease the weight of the car body-in-white has determined the success of the direct hot stamping process as a primary technology for the automotive sector. Thanks to this process, parts with high strength-to-weight ratio can be obtained along with high stiffness and increase of the crashworthiness properties. Moreover, the thinner metal sheets used to manufacture the pieces lead to a decrease of the total weight of the car body-in-white, with a consequent reduction of the CO2 emissions. The direct hot stamping process is becoming the key to obtain pieces with high mechanical properties, thanks to the quenching stage that allows the manufacture of complex shapes characterized by a fully martensitic structure, thanks to the forming stage at elevated temperature and subsequent hardening inside the cooled dies. The aim of this paper is the investigation of the influence that the forming temperature may have on the formability of 22MnB5 steel sheets, commonly used in the hot stamping process of automotive components. Nakajima tests were carried out at different temperatures and the Forming Limit Diagrams (FLDs) at rupture were obtained and analysed. The temperature influenced both the major and the minor strain at which the sheet failed, indicating that not only the formability increased at increasing temperature, but there was also a modification of the strain path, which means a modification of the strain states through which the part passes during the deformation process. Moreover, the influence of friction is studied using a model developed in the LS-Dyna FEM environment. The obtained data are of great importance for an accurate calibration of Finite Element (FE) models of the hot stamping of real components in order to get optimal process parameters to obtain defects-free pieces.

Food Stamps. Learning Packet No. 2.

ERIC Educational Resources Information Center

American Bar Association, Washington, DC. Clearinghouse for Offender Literacy Programs.

This package of instructional materials is designed to aid adults in prison to perform the functional skill of applying for food stamps. The materials consist of instructions for teachers, a sample application for food stamps, a student's work sheet and answer sheet, vocabulary flash cards, and resource materials on food stamps. (MKM)

RANKL-induced DC-STAMP Is Essential for Osteoclastogenesis

PubMed Central

Kukita, Toshio; Wada, Naohisa; Kukita, Akiko; Kakimoto, Takashi; Sandra, Ferry; Toh, Kazuko; Nagata, Kengo; Iijima, Tadahiko; Horiuchi, Madoka; Matsusaki, Hiromi; Hieshima, Kunio; Yoshie, Osamu; Nomiyama, Hisayuki

2004-01-01

Osteoclasts are bone-resorbing, multinucleated giant cells that are essential for bone remodeling and are formed through cell fusion of mononuclear precursor cells. Although receptor activator of nuclear factor–κB ligand (RANKL) has been demonstrated to be an important osteoclastogenic cytokine, the cell surface molecules involved in osteoclastogenesis are mostly unknown. Here, we report that the seven-transmembrane receptor-like molecule, dendritic cell–specific transmembrane protein (DC-STAMP) is involved in osteoclastogenesis. Expression of DC-STAMP is rapidly induced in osteoclast precursor cells by RANKL and other osteoclastogenic stimulations. Targeted inhibition of DC-STAMP by small interfering RNAs and specific antibody markedly suppressed the formation of multinucleated osteoclast-like cells. Overexpression of DC-STAMP enhanced osteoclastogenesis in the presence of RANKL. Furthermore, DC-STAMP directly induced the expression of the osteoclast marker tartrate-resistant acid phosphatase. These data demonstrate for the first time that DC-STAMP has an essential role in osteoclastogenesis. PMID:15452179

Printing transferable components using microstructured elastomeric surfaces with pressure modulated reversible adhesion

DOEpatents

Menard, Etienne; Rogers, John A.; Kim, Seok; Carlson, Andrew

2016-08-09

In a method of printing a transferable component, a stamp including an elastomeric post having three-dimensional relief features protruding from a surface thereof is pressed against a component on a donor substrate with a first pressure that is sufficient to mechanically deform the relief features and a region of the post between the relief features to contact the component over a first contact area. The stamp is retracted from the donor substrate such that the component is adhered to the stamp. The stamp including the component adhered thereto is pressed against a receiving substrate with a second pressure that is less than the first pressure to contact the component over a second contact area that is smaller than the first contact area. The stamp is then retracted from the receiving substrate to delaminate the component from the stamp and print the component onto the receiving substrate. Related apparatus and stamps are also discussed.

41 CFR 101-25.103-4 - Disposition of promotional materials, trading stamps, or bonus goods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... promotional materials, trading stamps, or bonus goods. 101-25.103-4 Section 101-25.103-4 Public Contracts and... materials, trading stamps, or bonus goods. (a) Agencies shall, through the lowest appropriate activity, arrange for transfer of promotional materials, trading stamps, or bonus goods, without reimbursement in...

78 FR 60304 - Information Collection Request Sent to the Office of Management and Budget (OMB) for Approval...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-01

...; Electronic Duck Stamp Program AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice; request for...: 1018-0135. Title: Electronic Duck Stamp Program. Service Form Number: 3-2341. Type of Request... Duck Stamp) annually. The stamps are a vital tool for wetland conservation. Ninety- eight cents out of...

41 CFR 101-25.103-4 - Disposition of promotional materials, trading stamps, or bonus goods.

Code of Federal Regulations, 2012 CFR

2012-07-01

... promotional materials, trading stamps, or bonus goods. 101-25.103-4 Section 101-25.103-4 Public Contracts and... materials, trading stamps, or bonus goods. (a) Agencies shall, through the lowest appropriate activity, arrange for transfer of promotional materials, trading stamps, or bonus goods, without reimbursement in...

41 CFR 101-25.103-4 - Disposition of promotional materials, trading stamps, or bonus goods.

Code of Federal Regulations, 2013 CFR

2013-07-01

... promotional materials, trading stamps, or bonus goods. 101-25.103-4 Section 101-25.103-4 Public Contracts and... materials, trading stamps, or bonus goods. (a) Agencies shall, through the lowest appropriate activity, arrange for transfer of promotional materials, trading stamps, or bonus goods, without reimbursement in...

41 CFR 101-25.103-4 - Disposition of promotional materials, trading stamps, or bonus goods.

Code of Federal Regulations, 2014 CFR

2014-07-01

... promotional materials, trading stamps, or bonus goods. 101-25.103-4 Section 101-25.103-4 Public Contracts and... materials, trading stamps, or bonus goods. (a) Agencies shall, through the lowest appropriate activity, arrange for transfer of promotional materials, trading stamps, or bonus goods, without reimbursement in...

41 CFR 101-25.103-4 - Disposition of promotional materials, trading stamps, or bonus goods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... promotional materials, trading stamps, or bonus goods. 101-25.103-4 Section 101-25.103-4 Public Contracts and... materials, trading stamps, or bonus goods. (a) Agencies shall, through the lowest appropriate activity, arrange for transfer of promotional materials, trading stamps, or bonus goods, without reimbursement in...

Earning the Stamp of Approval: How To Achieve Optimal Usability.

ERIC Educational Resources Information Center

Makar, Susan

2003-01-01

Describes the redesign of the Web site at the virtual library of the NIST (National Institute of Standards and Technology). Discusses usability problems with the original site, including navigation difficulties; focus groups to determine user needs; usability testing for the new Web site; and the importance of customer input. (LRW)

JPRS Report, Science and Technology, USSR: Science & Technology Policy.

DTIC Science & Technology

1988-07-18

half of the needs of the enterprises that belong to the ministry itself. The situa- tion is even worse with the supply with tools, stampings...economic turnover, if only of a small region.Ś The second half of the 1960’s and the 1970’s in USSR history were marked by a sharp increase of...intersectorial management of functioning complexes. Precisely for this reason the second half of the 1980’s is characterized,

Direct stamp of technology or origin on the genotypic and phenotypic variation of indigenous Saccharomyces cerevisiae population in a natural model of boiled grape juice fermentation into traditional Msalais wine in China.

PubMed

Zhu, Li-Xia; Wang, Guan-Qiong; Xue, Ju-Lan; Gou, Dong-Qi; Duan, Chang-Qing

2017-08-01

Saccharomyces cerevisiae strains worldwide show genetic and phenotypic diversity and their population substructures are greatly affected by their technological application or geographical origins. Msalais is a traditional wine obtained via a unique method of spontaneous fermentation of local boiled grape juice in Southern Xinjiang. We analyzed 436 indigenous S. cerevisiae strains associated with Msalais fermentation. These strains were highly diverse with respect to the interdelta region and 24 phenotypic traits, with apparent differentiation according to strain origins and technologies used to produce Msalais. The genetic and phenotypic diversity of strains from traditional workshops was higher than in strains from modern plants. These local strains had different origin- or technology-specific fermentative characteristics. Strains growing in large-scale fermentation tanks tolerated high temperature, whereas strains from traditional workshops tolerated high alcohol content (16%) and low temperature (13°C). Almost all the strains were characterized by the highest fermenting vigor, with weak H2S production and no histamine, cadaverine, phenethylamine and tryptamine production. Majority of strains had pronounced autolytic activity with high β-glucosidase and polygalacturonase activity and alcohol production. Our study reveals a direct stamp of technology or origin on genotypic and phenotypic variation of an indigenous S. cerevisiae population. © FEMS 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

41 CFR 101-25.103-3 - Trading stamps or bonus goods received from contractors.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 41 Public Contracts and Property Management 2 2011-07-01 2007-07-01 true Trading stamps or bonus... PROCUREMENT 25-GENERAL 25.1-General Policies § 101-25.103-3 Trading stamps or bonus goods received from contractors. When contracts contain a price reduction clause, any method (such as trading stamps or bonus...

39 CFR 551.3 - Procedure for selection of causes and recipient executive agencies.

Code of Federal Regulations, 2010 CFR

2010-07-01

... agencies is as follows: (a) In advance of the issuance of a semipostal stamp, the office of Stamp Services... solicited is to be sold. The office of Stamp Services may publicize the request for proposals through other means, as it determines in its discretion. (b) Proposals will be received by the office of Stamp...

39 CFR 551.3 - Procedure for selection of causes and recipient executive agencies.

Code of Federal Regulations, 2012 CFR

2012-07-01

... agencies is as follows: (a) In advance of the issuance of a semipostal stamp, the office of Stamp Services... solicited is to be sold. The office of Stamp Services may publicize the request for proposals through other means, as it determines in its discretion. (b) Proposals will be received by the office of Stamp...

39 CFR 551.3 - Procedure for selection of causes and recipient executive agencies.

Code of Federal Regulations, 2011 CFR

2011-07-01

... agencies is as follows: (a) In advance of the issuance of a semipostal stamp, the office of Stamp Services... solicited is to be sold. The office of Stamp Services may publicize the request for proposals through other means, as it determines in its discretion. (b) Proposals will be received by the office of Stamp...

39 CFR 551.3 - Procedure for selection of causes and recipient executive agencies.

Code of Federal Regulations, 2013 CFR

2013-07-01

... agencies is as follows: (a) In advance of the issuance of a semipostal stamp, the office of Stamp Services... solicited is to be sold. The office of Stamp Services may publicize the request for proposals through other means, as it determines in its discretion. (b) Proposals will be received by the office of Stamp...

39 CFR 551.3 - Procedure for selection of causes and recipient executive agencies.

Code of Federal Regulations, 2014 CFR

2014-07-01

... agencies is as follows: (a) In advance of the issuance of a semipostal stamp, the office of Stamp Services... solicited is to be sold. The office of Stamp Services may publicize the request for proposals through other means, as it determines in its discretion. (b) Proposals will be received by the office of Stamp...

41 CFR 101-25.103-3 - Trading stamps or bonus goods received from contractors.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 41 Public Contracts and Property Management 2 2014-07-01 2012-07-01 true Trading stamps or bonus... PROCUREMENT 25-GENERAL 25.1-General Policies § 101-25.103-3 Trading stamps or bonus goods received from contractors. When contracts contain a price reduction clause, any method (such as trading stamps or bonus...

41 CFR 101-25.103-3 - Trading stamps or bonus goods received from contractors.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 41 Public Contracts and Property Management 2 2012-07-01 2012-07-01 false Trading stamps or bonus... PROCUREMENT 25-GENERAL 25.1-General Policies § 101-25.103-3 Trading stamps or bonus goods received from contractors. When contracts contain a price reduction clause, any method (such as trading stamps or bonus...

26 CFR 1.451-4 - Accounting for redemption of trading stamps and coupons.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 26 Internal Revenue 6 2013-04-01 2013-04-01 false Accounting for redemption of trading stamps and... Included § 1.451-4 Accounting for redemption of trading stamps and coupons. (a) In general—(1) Subtraction from receipts. If an accrual method taxpayer issues trading stamps or premium coupons with sales, or an...

26 CFR 1.451-4 - Accounting for redemption of trading stamps and coupons.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 26 Internal Revenue 6 2012-04-01 2012-04-01 false Accounting for redemption of trading stamps and... Included § 1.451-4 Accounting for redemption of trading stamps and coupons. (a) In general—(1) Subtraction from receipts. If an accrual method taxpayer issues trading stamps or premium coupons with sales, or an...

26 CFR 1.451-4 - Accounting for redemption of trading stamps and coupons.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 26 Internal Revenue 6 2014-04-01 2014-04-01 false Accounting for redemption of trading stamps and... Included § 1.451-4 Accounting for redemption of trading stamps and coupons. (a) In general—(1) Subtraction from receipts. If an accrual method taxpayer issues trading stamps or premium coupons with sales, or an...

41 CFR 101-25.103-3 - Trading stamps or bonus goods received from contractors.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 41 Public Contracts and Property Management 2 2013-07-01 2012-07-01 true Trading stamps or bonus... PROCUREMENT 25-GENERAL 25.1-General Policies § 101-25.103-3 Trading stamps or bonus goods received from contractors. When contracts contain a price reduction clause, any method (such as trading stamps or bonus...

41 CFR 101-25.103-3 - Trading stamps or bonus goods received from contractors.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Trading stamps or bonus... PROCUREMENT 25-GENERAL 25.1-General Policies § 101-25.103-3 Trading stamps or bonus goods received from contractors. When contracts contain a price reduction clause, any method (such as trading stamps or bonus...

Microstamped opto-mechanical actuator for tactile displays

NASA Astrophysics Data System (ADS)

Camargo, Carlos J.; Torras, Núria; Campanella, Humberto; Marshall, Jean E.; Zinoviev, Kirill; Campo, Eva M.; Terentjev, Eugene M.; Esteve, Jaume

2011-10-01

Over the last few years, several technologies have been adapted for use in tactile displays, such as thermo-pneumatic actuators, piezoelectric polymers and dielectric elastomers. None of these approaches offers high-performance for refreshable Braille display system (RBDS), due to considerations of weight, power efficiency and response speed. Optical actuation offers an attractive alternative to solve limitations of current-art technologies, allowing electromechanical decoupling, elimination of actuation circuits and remote controllability. Creating these opticallydriven devices requires liquid crystal - carbon nanotube (LC-CNT) composites that show a reversible shape change in response to an applied light. This work thus reports on novel opto-actuated Braille dots based on LC-CNT composite and silicon mold microstamping. The manufacturing approach succeeds on producing blisters according to the Braille standard for the visually impaired, by taking shear-aligned LC-CNT films and silicon stamps. For this application, we need to define specifically-shaped structures. Some technologies have succeeded on elastomer microstructuring. Nevertheless, they are not applicable for LC-CNT molding because they do not consider the stretching of the polymer which is required for LC-CNT fabrication. Our process demonstrates that composites micro-molding and their 3-D structuring is feasible by silicon-based stamping. Its work principle involves the mechanical stretching, allowing the LC mesogens alignment.

Monitoring gait in multiple sclerosis with novel wearable motion sensors

PubMed Central

McGinnis, Ryan S.; Seagers, Kirsten; Motl, Robert W.; Sheth, Nirav; Wright, John A.; Ghaffari, Roozbeh; Sosnoff, Jacob J.

2017-01-01

Background Mobility impairment is common in people with multiple sclerosis (PwMS) and there is a need to assess mobility in remote settings. Here, we apply a novel wireless, skin-mounted, and conformal inertial sensor (BioStampRC, MC10 Inc.) to examine gait characteristics of PwMS under controlled conditions. We determine the accuracy and precision of BioStampRC in measuring gait kinematics by comparing to contemporary research-grade measurement devices. Methods A total of 45 PwMS, who presented with diverse walking impairment (Mild MS = 15, Moderate MS = 15, Severe MS = 15), and 15 healthy control subjects participated in the study. Participants completed a series of clinical walking tests. During the tests participants were instrumented with BioStampRC and MTx (Xsens, Inc.) sensors on their shanks, as well as an activity monitor GT3X (Actigraph, Inc.) on their non-dominant hip. Shank angular velocity was simultaneously measured with the inertial sensors. Step number and temporal gait parameters were calculated from the data recorded by each sensor. Visual inspection and the MTx served as the reference standards for computing the step number and temporal parameters, respectively. Accuracy (error) and precision (variance of error) was assessed based on absolute and relative metrics. Temporal parameters were compared across groups using ANOVA. Results Mean accuracy±precision for the BioStampRC was 2±2 steps error for step number, 6±9ms error for stride time and 6±7ms error for step time (0.6–2.6% relative error). Swing time had the least accuracy±precision (25±19ms error, 5±4% relative error) among the parameters. GT3X had the least accuracy±precision (8±14% relative error) in step number estimate among the devices. Both MTx and BioStampRC detected significantly distinct gait characteristics between PwMS with different disability levels (p<0.01). Conclusion BioStampRC sensors accurately and precisely measure gait parameters in PwMS across diverse walking impairment levels and detected differences in gait characteristics by disability level in PwMS. This technology has the potential to provide granular monitoring of gait both inside and outside the clinic. PMID:28178288

A behaviour study on the potential for direct transmission of tuberculosis from possums (Trichosurus vulpecula) to alpacas (Lama pacos), and the converse from alpacas to possums.

PubMed

Black, H; Simper, J M; Bloom, D; Bloom, K

1999-12-01

To evaluate the potential for the direct transmission of tuberculosis from possums to alpacas, and vice versa. A field study was conducted on an alpaca farm in Northland, New Zealand on 7 January 1999. Observations were recorded on the interaction of one group of male alpacas with a simulated dead possum, one male and one female alpaca group with a simulated terminally tuberculous possum, and one group of male alpacas with a normal possum in an enclosure from which the animals could not escape. The possum was sedated with ketamine as hydrochloride to simulate death (inactive; no movement), and terminal illness (active, inco-ordinated movement around the paddock). The observations were based on the focal animal sampling technique, they were un-replicated, and recorded visually and manually with intermittent still photography. Both male and female alpacas showed strongly inquisitive interaction with the possum. They clustered around the possum (focal animal) very soon after it was observed by the first member of the group. The interest of the majority of both sex groups remained high for the observation periods of approximately 30 minutes, and most individuals remained within 5 metres of the possum for that time. Approximately 50% of the alpacas were within possible aerosol transmission distance of 2 metres from the sedated, erratically mobile possum with their heads towards it for approximately 50% of the two observation periods. Aggressive behaviour was recorded for a young male with stamping on the moving possum. Similar, but more vigorous and prolonged stamping behaviour was recorded for a female with a young (<1 week) offspring (cria). The stamping behaviour was accompanied by very close nose to nose contact of the alpaca and possum. At one point the female threw the possum approximately 1.5 metres in the air with her teeth. The group of male alpacas placed in an enclosure with an unsedated normal possum generally moved away from the possum during its rapid active attempts to escape. When it became inactive their approaches were cautious and only once elicited a defence reaction from the possum, from which they recoiled. One male made one attempt to stamp on the active possum. Soon after the possum became inactive in a small loose hay pile, the alpacas lost interest in it. The alpaca / possum behavioural interactions show there is potential for direct aerosol transmission of tuberculosis from possums to alpacas, but probably not from alpacas to possums.

Postage stamps: A convergence of metallurgy, art, and history

NASA Astrophysics Data System (ADS)

Habashi, Fathi

2002-04-01

Postage stamps have been used around the world to commemorate, in miniature, significant events and people, including those of importance in the history of metals and mineral production. From the presence of gold artifacts in an ancient Egyptian tomb to the role of uranium in nuclear power, stamps have captured the evolution of metallurgical processes. This article highlights some of those stamps.

46. DETAIL VIEW OF THE MORTAR BOXES, STAMP BATTERIES AND ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

46. DETAIL VIEW OF THE MORTAR BOXES, STAMP BATTERIES AND AMALGAMATION TABLES. NOTE FULTON IRON WORKS, SAM FRANCISCO 1908 STAMPED INTO THE MORTAR BOX. ALSO NOTE THE DIES RESTING ON THE OUTSIDE OF THE MORTAR BOX BY THE SECOND STAMP BATTERY FROM THE CAMERA POSITION. - Standard Gold Mill, East of Bodie Creek, Northeast of Bodie, Bodie, Mono County, CA

A unique patterned diamond stamp for a periodically hierarchical nanoarray structure.

PubMed

Wang, Yi; Shen, Yanting; Xu, Weiqing; Xu, Shuping; Li, Hongdong

2016-09-23

A diamond stamp with a hierarchical pattern was designed for the direct preparation of a periodic nanoarray structure, which was prepared by the reactive ion etching technique with a hierarchical ultrathin alumina membrane (HUTAM) as a mask. The optimal etching conditions for fabricating the diamond stamp were discussed in order to realize a vertical nanopore structure, avoiding structural damage from lateral etching. By using this diamond stamp, a polymer film with the desired hierarchical nanorod array structure can be obtained easily via the simple stamping process, which greatly simplifies the processing procedure. More importantly, the stamp is reusable because of its super-hardness, which ensures the reproducibility of the nanorod array pattern. Another merit is that the smooth surface of the etched diamond can avoid the use of a release agent. Our results prove that this hard stamp can be used for quick preparation of an elaborate periodic nanoarray structure. This study is significant in that it solves the problems of high cost and easy damage of stamps in nanoimprint lithography, and it might inspire more sophisticated applications of such an ordered structure in nanoplasmonics, biochemical sensing and nanophotonic devices.

Carbon nanotube substrates and catalyzed hot stamp for polishing and patterning the substrates

DOEpatents

Wang, Yuhuang [Evanston, IL; Hauge, Robert H [Houston, TX; Schmidt, Howard K [Houston, TX; Kim, Myung Jong [Houston, TX; Kittrell, W Carter [Houston, TX

2009-09-08

The present invention is generally directed to catalyzed hot stamp methods for polishing and/or patterning carbon nanotube-containing substrates. In some embodiments, the substrate, as a carbon nanotube fiber end, is brought into contact with a hot stamp (typically at 200-800.degree. C.), and is kept in contact with the hot stamp until the morphology/patterns on the hot stamp have been transferred to the substrate. In some embodiments, the hot stamp is made of material comprising one or more transition metals (Fe, Ni, Co, Pt, Ag, Au, etc.), which can catalyze the etching reaction of carbon with H.sub.2, CO.sub.2, H.sub.2O, and/or O.sub.2. Such methods can (1) polish the carbon nanotube-containing substrate with a microscopically smooth finish, and/or (2) transfer pre-defined patterns from the hot stamp to the substrate. Such polished or patterned carbon nanotube substrates can find application as carbon nanotube electrodes, field emitters, and field emitter arrays for displays and electron sources.

Manufacture of conical springs with elastic medium technology improvement

NASA Astrophysics Data System (ADS)

Kurguzov, S. A.; Mikhailova, U. V.; Kalugina, O. B.

2018-01-01

This article considers the manufacturing technology improvement by using an elastic medium in the stamping tool forming space to improve the conical springs performance characteristics and reduce the costs of their production. Estimation technique of disk spring operational properties is developed by mathematical modeling of the compression process during the operation of a spring. A technique for optimizing the design parameters of a conical spring is developed, which ensures a minimum voltage value when operated in the edge of the spring opening.

Hospital Nurses' Work Activity in a Technology-Rich Environment: A Triangulated Quality Improvement Assessment.

PubMed

Higgins, Linda W; Shovel, Judith A; Bilderback, Andrew L; Lorenz, Holly L; Martin, Susan C; Rogers, Debra J; Minnier, Tamra E

The aim of this project was to describe hospital nurses' work activity through observations, nurses' perceptions of time spent on tasks, and electronic health record time stamps. Nurses' attitudes toward technology and patients' perceptions and satisfaction with nurses' time at the bedside were also examined. Activities most frequently observed included documenting in and reviewing the electronic health record. Nurses' perceptions of time differed significantly from observations, and most patients rated their satisfaction with nursing time as excellent or good.

Connecting the dots across time: reconstruction of single-cell signalling trajectories using time-stamped data

NASA Astrophysics Data System (ADS)

Mukherjee, Sayak; Stewart, David; Stewart, William; Lanier, Lewis L.; Das, Jayajit

2017-08-01

Single-cell responses are shaped by the geometry of signalling kinetic trajectories carved in a multidimensional space spanned by signalling protein abundances. It is, however, challenging to assay a large number (more than 3) of signalling species in live-cell imaging, which makes it difficult to probe single-cell signalling kinetic trajectories in large dimensions. Flow and mass cytometry techniques can measure a large number (4 to more than 40) of signalling species but are unable to track single cells. Thus, cytometry experiments provide detailed time-stamped snapshots of single-cell signalling kinetics. Is it possible to use the time-stamped cytometry data to reconstruct single-cell signalling trajectories? Borrowing concepts of conserved and slow variables from non-equilibrium statistical physics we develop an approach to reconstruct signalling trajectories using snapshot data by creating new variables that remain invariant or vary slowly during the signalling kinetics. We apply this approach to reconstruct trajectories using snapshot data obtained from in silico simulations, live-cell imaging measurements, and, synthetic flow cytometry datasets. The application of invariants and slow variables to reconstruct trajectories provides a radically different way to track objects using snapshot data. The approach is likely to have implications for solving matching problems in a wide range of disciplines.

Research on liquid impact forming technology of double-layered tubes

NASA Astrophysics Data System (ADS)

Sun, Changying; Liu, Jianwei; Yao, Xinqi; Huang, Beixing; Li, Yuhan

2018-03-01

A double-layered tube is widely used and developed in various fields because of its perfect comprehensive performance and design. With the advent of the era of a double-layered tube, the requirements for double layered tube forming quality, manufacturing cost and forming efficiency are getting higher, so forming methods of a double-layered tube are emerged in an endless stream, the forming methods of a double-layered tube have a great potential in the future. The liquid impact forming technology is a combination of stamping technology and hydroforming technology. Forming a double-layered tube has huge advantages in production cost, quality and efficiency.

New trends in metal forming in the USA

NASA Astrophysics Data System (ADS)

1982-05-01

The use of lasers in sheet metal stamping, hydraulic presses, cold pressing, and deformation of titanium alloy to produce components which do not require subsequent machining are discussed. Superplastic deformation techniques could lead to cost savings of 90% in the aerospace industry. Precision forging and welding technologies can considerably reduce raw material costs, but investment costs are high.

50 CFR 91.1 - Purpose of regulations.

Code of Federal Regulations, 2010 CFR

2010-10-01

...) MISCELLANEOUS PROVISIONS MIGRATORY BIRD HUNTING AND CONSERVATION STAMP CONTEST Introduction § 91.1 Purpose of... be used for the annual Migratory Bird Hunting and Conservation Stamp (Federal Duck Stamp). (b) All...

50 CFR 91.1 - Purpose of regulations.

Code of Federal Regulations, 2011 CFR

2011-10-01

...) MISCELLANEOUS PROVISIONS MIGRATORY BIRD HUNTING AND CONSERVATION STAMP CONTEST Introduction § 91.1 Purpose of... be used for the annual Migratory Bird Hunting and Conservation Stamp (Federal Duck Stamp). (b) All...

Validation of a Nutritional Screening Tool for Ambulatory Use in Pediatrics.

PubMed

Rub, Gal; Marderfeld, Luba; Poraz, Irit; Hartman, Corina; Amsel, Shlomo; Rosenbaum, Israel; Pergamentzev-Karpol, Shiri; Monsonego-Ornan, Efrat; Shamir, Raanan

2016-05-01

To evaluate the use of Screening Tool for the Assessment of Malnutrition in Pediatrics (STAMP) in a primary health care clinic in the community and to assess the impact of its use on medical staff's awareness of nutritional status. STAMP scoring system was tested as is and with modifications in the ambulatory setting. Nutritional risk according to STAMP was compared with a detailed nutritional assessment performed by a registered dietitian. Recording of nutrition-related data and anthropometric measurements in medical files were compared prior and post implementation. Sixty children were included (31 girls, 52%), ages between 1 and 6 years, mean age 2.8 ± 1.5 (mean ± SD). STAMP scores yielded a fair agreement between STAMP and the dietitian's nutritional assessment: κ = 0.47 (95% confidence interval [CI] 0.24-0.7), sensitivity of 47.62% (95% CI 28.34-67.63). Modified STAMP yielded more substantial agreement: κ = 0.57 (95% CI 0.35-0.79), sensitivity of 76.19% (95% CI 54.91-89.37), specificity of 82.05% (95% CI 67.33-91.02). The use of STAMP resulted in an increase in recording of appetite, dietary intake, and anthropometric measurements. Modification of the STAMP improved nutritional risk evaluation in community setting. The use of STAMP in a primary health care clinic raised clinician's awareness to nutritional status. Further work will identify whether this could be translated into lower malnutrition rates and better child care.

Attenuated Total Reflection Fourier Transform Infrared (ATR FT-IR) Spectroscopy as a Forensic Method to Determine the Composition of Inks Used to Print the United States One-cent Blue Benjamin Franklin Postage Stamps of the 19th Century.

PubMed

Brittain, Harry G

2016-01-01

Through the combined use of infrared (IR) absorption spectroscopy and attenuated total reflectance (ATR) sampling, the composition of inks used to print the many different types of one-cent Benjamin Franklin stamps of the 19th century has been established. This information permits a historical evaluation of the formulations used at various times, and also facilitates the differentiation of the various stamps from each other. In two instances, the ink composition permits the unambiguous identification of stamps whose appearance is identical, and which (until now) have only been differentiated through estimates of the degree of hardness or softness of the stamp paper, or through the presence or absence of a watermark in the paper. In these instances, the use of ATR Fourier transform infrared spectroscopy (FT-IR) spectroscopy effectively renders irrelevant two 100-year-old practices of stamp identification. Furthermore, since the use of ATR sampling makes it possible to obtain the spectrum of a stamp still attached to its cover, it is no longer necessary to identify these blue Franklin stamps using their cancellation dates. © The Author(s) 2015.

50 CFR 91.21 - Selection and qualification of contest judges.

Code of Federal Regulations, 2010 CFR

2010-10-01

... eligible waterfowl species, an understanding of the wildlife sporting world in which the Duck Stamp is used, an awareness of philately and the role the Duck Stamp plays in stamp collecting, and demonstrated...

50 CFR 91.21 - Selection and qualification of contest judges.

Code of Federal Regulations, 2013 CFR

2013-10-01

... eligible waterfowl species, an understanding of the wildlife sporting world in which the Duck Stamp is used, an awareness of philately and the role the Duck Stamp plays in stamp collecting, and demonstrated...

50 CFR 91.21 - Selection and qualification of contest judges.

Code of Federal Regulations, 2011 CFR

2011-10-01

... eligible waterfowl species, an understanding of the wildlife sporting world in which the Duck Stamp is used, an awareness of philately and the role the Duck Stamp plays in stamp collecting, and demonstrated...

50 CFR 91.21 - Selection and qualification of contest judges.

Code of Federal Regulations, 2014 CFR

2014-10-01

... eligible waterfowl species, an understanding of the wildlife sporting world in which the Duck Stamp is used, an awareness of philately and the role the Duck Stamp plays in stamp collecting, and demonstrated...

50 CFR 91.21 - Selection and qualification of contest judges.

Code of Federal Regulations, 2012 CFR

2012-10-01

... eligible waterfowl species, an understanding of the wildlife sporting world in which the Duck Stamp is used, an awareness of philately and the role the Duck Stamp plays in stamp collecting, and demonstrated...

A Fully Automated and Robust Method to Incorporate Stamping Data in Crash, NVH and Durability Analysis

NASA Astrophysics Data System (ADS)

Palaniswamy, Hariharasudhan; Kanthadai, Narayan; Roy, Subir; Beauchesne, Erwan

2011-08-01

Crash, NVH (Noise, Vibration, Harshness), and durability analysis are commonly deployed in structural CAE analysis for mechanical design of components especially in the automotive industry. Components manufactured by stamping constitute a major portion of the automotive structure. In CAE analysis they are modeled at a nominal state with uniform thickness and no residual stresses and strains. However, in reality the stamped components have non-uniformly distributed thickness and residual stresses and strains resulting from stamping. It is essential to consider the stamping information in CAE analysis to accurately model the behavior of the sheet metal structures under different loading conditions. Especially with the current emphasis on weight reduction by replacing conventional steels with aluminum and advanced high strength steels it is imperative to avoid over design. Considering this growing need in industry, a highly automated and robust method has been integrated within Altair Hyperworks® to initialize sheet metal components in CAE models with stamping data. This paper demonstrates this new feature and the influence of stamping data for a full car frontal crash analysis.

78 FR 56679 - Procurement List; Deletions

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-13

..., Hines, IL, General Services Administration, New York, NY NSN: 7520-01-453-1967--4 PC Stamps Kit, `Route-It Set' NSN: 7520-01-453-1968--4 PC Stamps Kit, `Accountant Set' NSN: 7520-01-453-1969--4 PC Stamps...

Aluminium Pneumoconiosis I. In Vitro Comparison of Stamped Aluminium Powders Containing Different Lubricating Agents and a Granular Aluminium Powder

PubMed Central

Corrin, B.

1963-01-01

The discrepancy in previous reports of the action of aluminium on the lung may be explained by differences between stamped and granular aluminium powders. A stamped powder of the variety causing pulmonary fibrosis showed a brisk reaction with water, but a granular powder was unreactive. This difference is primarily due to the granular particles being covered by inert aluminium oxide, the formation of which is partially prevented in the stamping process by stearine and mineral oil. The reactivity of the flake-like stamped particles is also dependent on their large surface area per unit volume. The appearance of aluminium pneumoconiosis in Britain is explained by the introduction of mineral oil into the stamping industry for, in contrast to stearine, mineral oil permits the powder to react with water. The lung damage is believed to be caused by a soluble form of aluminium. PMID:14072616

Optical force stamping lithography

PubMed Central

Nedev, Spas; Urban, Alexander S.; Lutich, Andrey A.; Feldmann, Jochen

2013-01-01

Here we introduce a new paradigm of far-field optical lithography, optical force stamping lithography. The approach employs optical forces exerted by a spatially modulated light field on colloidal nanoparticles to rapidly stamp large arbitrary patterns comprised of single nanoparticles onto a substrate with a single-nanoparticle positioning accuracy well beyond the diffraction limit. Because the process is all-optical, the stamping pattern can be changed almost instantly and there is no constraint on the type of nanoparticle or substrates used. PMID:21992538

7 CFR 281.10 - Appeals.

Code of Federal Regulations, 2011 CFR

2011-01-01

... of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM ADMINISTRATION OF THE FOOD STAMP PROGRAM ON INDIAN... failure of an agency of State government to properly administer the Food Stamp Program; (iii) The...

Effects on response rates and costs of stamps vs business reply in a mail survey of physicians.

PubMed

Urban, N; Anderson, G L; Tseng, A

1993-05-01

In the general population, the use of stamps rather than business reply postage significantly improves response rates in mail surveys. Among physicians, however, a smaller effect might be anticipated due to their greater sophistication. An experiment was conducted to test the hypothesis that stamps would improve response rates and lower costs in a physician survey that included intensive follow up. In 1989, 380 physicians who reported providing primary care were surveyed. The protocol included two mailings, a postcard reminder, and two telephone reminders. Physicians were randomly assigned to receive a return envelope with a first-class stamp or an envelope that had been preprinted "business reply mail" in the first and second mailings. Response rates, calculated as completed surveys divided by eligible physicians, were 83.8 and 72.1% for stamps and business reply respectively, a difference of 11.7 percentage points (p < 0.01). Moreover, the total cost per completed survey was $11.18 for the physicians receiving stamps and $14.25 for the physicians receiving business reply. As in mail surveys of the general public, the use of first-class stamps on return envelopes both improves response rates and reduces cost in surveys of physicians.

41 CFR 109-25.103 - Promotional materials, trading stamps, or bonus goods.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 41 Public Contracts and Property Management 3 2011-01-01 2011-01-01 false Promotional materials, trading stamps, or bonus goods. 109-25.103 Section 109-25.103 Public Contracts and Property Management..., trading stamps, or bonus goods. ...

48 CFR 246.472 - Inspection stamping.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., DEPARTMENT OF DEFENSE CONTRACT MANAGEMENT QUALITY ASSURANCE Government Contract Quality Assurance 246.472 Inspection stamping. (a) DoD quality inspection approval marking designs (stamps) may be used for both prime...) Policies and procedures regarding the use of National Aeronautics and Space Administration (NASA) quality...

Football or Physics?

ERIC Educational Resources Information Center

Handorf, William C.

2007-01-01

In this article, the author discusses the United States commemorative stamps and what the stamp-buying public knows about higher education. United States commemorative stamps have illustrated individuals such as Marilyn Monroe (1995); characters such as Bugs Bunny (1997); American motorcycles (2006); and Valentine candy hearts (2004). Higher…

41 CFR 109-25.103 - Promotional materials, trading stamps, or bonus goods.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 41 Public Contracts and Property Management 3 2014-01-01 2014-01-01 false Promotional materials, trading stamps, or bonus goods. 109-25.103 Section 109-25.103 Public Contracts and Property Management..., trading stamps, or bonus goods. ...

41 CFR 109-25.103 - Promotional materials, trading stamps, or bonus goods.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 41 Public Contracts and Property Management 3 2013-07-01 2013-07-01 false Promotional materials, trading stamps, or bonus goods. 109-25.103 Section 109-25.103 Public Contracts and Property Management..., trading stamps, or bonus goods. ...

41 CFR 109-25.103 - Promotional materials, trading stamps, or bonus goods.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 41 Public Contracts and Property Management 3 2012-01-01 2012-01-01 false Promotional materials, trading stamps, or bonus goods. 109-25.103 Section 109-25.103 Public Contracts and Property Management..., trading stamps, or bonus goods. ...

41 CFR 109-25.103 - Promotional materials, trading stamps, or bonus goods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Promotional materials, trading stamps, or bonus goods. 109-25.103 Section 109-25.103 Public Contracts and Property Management..., trading stamps, or bonus goods. ...

Applying STAMP in Accident Analysis

NASA Technical Reports Server (NTRS)

Leveson, Nancy; Daouk, Mirna; Dulac, Nicolas; Marais, Karen

2003-01-01

Accident models play a critical role in accident investigation and analysis. Most traditional models are based on an underlying chain of events. These models, however, have serious limitations when used for complex, socio-technical systems. Previously, Leveson proposed a new accident model (STAMP) based on system theory. In STAMP, the basic concept is not an event but a constraint. This paper shows how STAMP can be applied to accident analysis using three different views or models of the accident process and proposes a notation for describing this process.

Integrated software package STAMP for minor planets

NASA Technical Reports Server (NTRS)

Kochetova, O. M.; Shor, Viktor A.

1992-01-01

The integrated software package STAMP allowed for rapid and exact reproduction of the tables of the year-book 'Ephemerides of Minor Planets.' Additionally, STAMP solved the typical problems connected with the use of the year-book. STAMP is described. The year-book 'Ephemerides of Minor Planets' (EMP) is a publication used in many astronomical institutions around the world. It contains all the necessary information on the orbits of the numbered minor planets. Also, the astronomical coordinates are provided for each planet during its suitable observation period.

Comparison of stapedotomy minus prosthesis, circumferential stapes mobilization, and small fenestra stapedotomy for stapes fixation.

PubMed

Acar, Gül Ozbilen; Kivekäs, Ilkka; Hanna, Bassem M; Huang, Lin; Gopen, Quinton; Poe, Dennis S

2014-04-01

To compare the outcomes of 3 surgical techniques for primary stapes fixation: stapedotomy minus prosthesis (STAMP), circumferential stapes mobilization (CSM), and small fenestra stapedotomy (SFS). Retrospective review of 277 primary cases operated for stapes fixation from 1997 to 2007. Tertiary academic center. Consecutive adult and pediatric cases operated for conductive hearing loss because of stapes fixation. STAMP was performed for otosclerosis limited to the anterior footplate, CSM was conducted for congenital stapes fixation, SFS was performed for more extensive otosclerosis or anatomic contraindications to STAMP/CSM. Pure-tone audiometry was performed preoperatively and postoperatively (3-6 wk) and the most recent long-term results (≥ 12 mo). Ninety-nine ears in 90 patients had audiologic follow-up data over 12 months. Sixty-seven ears (68%) underwent SFS, 16 (16%) STAMP, and 16 (16%) CSM. There was significant improvement in average air conduction (AC) thresholds and air-bone gap (ABG) for all techniques. Mean ABG for SFS closed from 29 to 7.1 dB (SD, 6.0), for STAMP from 29 to 3.8 dB (SD, 5.8 dB), and for CSM from 34 to 20 dB (SD, 8.2 dB). AC results were better in the STAMP than in the SFS group, especially in high frequencies. Bone conduction improvements were seen in all groups, highest in STAMP (4.3 dB) and CSM (3.8 dB) groups, but the differences between groups were not statistically significant. Satisfactory hearing results were achieved with all the techniques, and STAMP showed better hearing outcomes, especially in high frequencies. CSM is a good option for children and patients in whom it is desirable to avoid a footplate fenestration or prosthesis. CSM and STAMP had significantly higher rates of revision for refixation than SFS.

7 CFR 281.1 - General purpose and scope.

Code of Federal Regulations, 2010 CFR

2010-01-01

... organizations on reservations can administer the Food Stamp Program. The Act authorizes the Secretary to pay... Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM ADMINISTRATION OF THE FOOD STAMP PROGRAM ON INDIAN...

75 FR 11913 - Chrysler, LLC, Sterling Stamping Plant, Including On-Site Leased Workers from Caravan Knight...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-12

... Stamping Plant, Including On-Site Leased Workers from Caravan Knight Facilities Management LLC, Sterling... stampings. New information shows that workers leased from Caravan Knight Facilities Management LLC were... workers leased from Caravan Knight Facilities [[Page 11914

Stamping Out Misconceptions.

ERIC Educational Resources Information Center

Bradley, J. D.; Brand, M.

1985-01-01

Describes the use of rubber hand-stamps to generate molecular pictures. These stamps (prepared with shapes of atoms and molecules at little cost by small, local print shops) can be used in creating pictures representing the microscopic state that can be linked to macroscopic descriptions for active conceptual exploration. (JN)

7 CFR 273.25 - Simplified Food Stamp Program.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 4 2014-01-01 2014-01-01 false Simplified Food Stamp Program. 273.25 Section 273.25 Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM CERTIFICATION OF ELIGIBLE HOUSEHOLDS Program Alternatives...

7 CFR 273.25 - Simplified Food Stamp Program.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 4 2012-01-01 2012-01-01 false Simplified Food Stamp Program. 273.25 Section 273.25 Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM CERTIFICATION OF ELIGIBLE HOUSEHOLDS Program Alternatives...

7 CFR 273.25 - Simplified Food Stamp Program.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 4 2011-01-01 2011-01-01 false Simplified Food Stamp Program. 273.25 Section 273.25 Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM CERTIFICATION OF ELIGIBLE HOUSEHOLDS Program Alternatives...

7 CFR 273.25 - Simplified Food Stamp Program.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 4 2013-01-01 2013-01-01 false Simplified Food Stamp Program. 273.25 Section 273.25 Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM CERTIFICATION OF ELIGIBLE HOUSEHOLDS Program Alternatives...

7 CFR 281.1 - General purpose and scope.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM ADMINISTRATION OF THE FOOD STAMP PROGRAM ON INDIAN... Program on Indian reservations either separately or concurrently with the Food distribution program. In order to assure that the Food Stamp Program is responsive to the needs of Indians on reservations, State...

7 CFR 281.6 - Liabilities and sanctions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM ADMINISTRATION OF THE FOOD STAMP PROGRAM ON INDIAN RESERVATIONS § 281.6 Liabilities and sanctions. An ITO administering the Food Stamp Program on a reservation is...

7 CFR 281.6 - Liabilities and sanctions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM ADMINISTRATION OF THE FOOD STAMP PROGRAM ON INDIAN RESERVATIONS § 281.6 Liabilities and sanctions. An ITO administering the Food Stamp Program on a reservation is...

High Thermal Conductivity and High Wear Resistance Tool Steels for cost-effective Hot Stamping Tools

NASA Astrophysics Data System (ADS)

Valls, I.; Hamasaiid, A.; Padré, A.

2017-09-01

In hot stamping/press hardening, in addition to its shaping function, the tool controls the cycle time, the quality of the stamped components through determining the cooling rate of the stamped blank, the production costs and the feasibility frontier for stamping a given component. During the stamping, heat is extracted from the stamped blank and transported through the tool to the cooling medium in the cooling lines. Hence, the tools’ thermal properties determine the cooling rate of the blank, the heat transport mechanism, stamping times and temperature distribution. The tool’s surface resistance to adhesive and abrasive wear is also an important cost factor, as it determines the tool durability and maintenance costs. Wear is influenced by many tool material parameters, such as the microstructure, composition, hardness level and distribution of strengthening phases, as well as the tool’s working temperature. A decade ago, Rovalma developed a hot work tool steel for hot stamping that features a thermal conductivity of more than double that of any conventional hot work tool steel. Since that time, many complimentary grades have been developed in order to provide tailored material solutions as a function of the production volume, degree of blank cooling and wear resistance requirements, tool geometries, tool manufacturing method, type and thickness of the blank material, etc. Recently, Rovalma has developed a new generation of high thermal conductivity, high wear resistance tool steel grades that enable the manufacture of cost effective tools for hot stamping to increase process productivity and reduce tool manufacturing costs and lead times. Both of these novel grades feature high wear resistance and high thermal conductivity to enhance tool durability and cut cycle times in the production process of hot stamped components. Furthermore, one of these new grades reduces tool manufacturing costs through low tool material cost and hardening through readily available gas-quenching, whereas the other new grade enables a faster manufacturing of the tool at reduced cost by eliminating the time and money consuming high temperature hardening altogether. The latter newly developed grade can be hardened from a soft delivery state for easy machining to 52 HRc by way of a simple low temperature precipitation hardening. In this work, these new grades and the role of the tool material’s thermal, mechanical and tribological properties as well as their processing features will be discussed in light of enabling the manufacture of intelligent hot stamping tools.

Stress-Strain Characterization for Reversed Loading Path and Constitutive Modeling for AHSS Springback Predictions

NASA Astrophysics Data System (ADS)

Zhu, Hong; Huang, Mai; Sadagopan, Sriram; Yao, Hong

2017-09-01

With increasing vehicle fuel economy standards, automotive OEMs are widely using various AHSS grades including DP, TRIP, CP and 3rd Gen AHSS to reduce vehicle weight due to their good combination of strength and formability. As one of enabling technologies for AHSS application, the requirement for requiring accurate prediction of springback for cold stamped AHSS parts stimulated a large number of investigations in the past decade with reversed loading path at large strains followed by constitutive modeling. With a spectrum of complex loading histories occurring in production stamping processes, there were many challenges in this field including issues of test data reliability, loading path representability, constitutive model robustness and non-unique constitutive parameter-identification. In this paper, various testing approaches and constitutive modeling will be reviewed briefly and a systematic methodology from stress-strain characterization, constitutive model parameter identification for material card generation will be presented in order to support automotive OEM’s need on virtual stamping. This systematic methodology features a tension-compression test at large strain with robust anti-buckling device with concurrent friction force correction, properly selected loading paths to represent material behavior during different springback modes as well as the 10-parameter Yoshida model with knowledge-based parameter-identification through nonlinear optimization. Validation cases for lab AHSS parts will also be discussed to check applicability of this methodology.

39 CFR 551.8 - Cost offset policy.

Code of Federal Regulations, 2010 CFR

2010-07-01

... semipostal stamps; (5) Costs of stamp sales (including employee salaries and benefits); (6) Costs associated... 39 Postal Service 1 2010-07-01 2010-07-01 false Cost offset policy. 551.8 Section 551.8 Postal Service UNITED STATES POSTAL SERVICE POSTAGE PROGRAMS SEMIPOSTAL STAMP PROGRAM § 551.8 Cost offset policy...

7 CFR 273.25 - Simplified Food Stamp Program.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 4 2010-01-01 2010-01-01 false Simplified Food Stamp Program. 273.25 Section 273.25 Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM CERTIFICATION OF ELIGIBLE HOUSEHOLDS § 273.25 Simplified...

7 CFR 281.3 - Determination of failure.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM ADMINISTRATION OF THE FOOD STAMP PROGRAM ON INDIAN... deficiency in a State agency operation of the Food Stamp Program on all or part of an Indian reservation may...

Photovoltaic cells with a graded active region achieved using stamp transfer printing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Forrest, Stephen R.; Lee, Jun Yeob; Cho, Yong Joo

Disclosed herein are processes for fabricating organic photosensitive optoelectronic devices with a vertical compositionally graded organic active layer. The processes use either a single-stamp or double-stamp printing technique to transfer the vertical compositionally graded organic active layer from a starting substrate to a device layer.

Volcanology by Courier: Science in Stamps.

ERIC Educational Resources Information Center

Glenn, William H.

1981-01-01

Summarized are five activities involving collection of postage stamps picturing volcanoes or related scenes for use as part of or at the conclusion of the study of volcanoes. Activity topics include volcanic features, location of volcanoes, related land features where volcanoes are not located, and making one's own volcano stamps. (DS)

STAMPS: Software Tool for Automated MRI Post-processing on a supercomputer.

PubMed

Bigler, Don C; Aksu, Yaman; Miller, David J; Yang, Qing X

2009-08-01

This paper describes a Software Tool for Automated MRI Post-processing (STAMP) of multiple types of brain MRIs on a workstation and for parallel processing on a supercomputer (STAMPS). This software tool enables the automation of nonlinear registration for a large image set and for multiple MR image types. The tool uses standard brain MRI post-processing tools (such as SPM, FSL, and HAMMER) for multiple MR image types in a pipeline fashion. It also contains novel MRI post-processing features. The STAMP image outputs can be used to perform brain analysis using Statistical Parametric Mapping (SPM) or single-/multi-image modality brain analysis using Support Vector Machines (SVMs). Since STAMPS is PBS-based, the supercomputer may be a multi-node computer cluster or one of the latest multi-core computers.

Estimation of network path segment delays

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nichols, Kathleen Marie

A method for estimation of a network path segment delay includes determining a scaled time stamp for each packet of a plurality of packets by scaling a time stamp for each respective packet to minimize a difference of at least one of a frequency and a frequency drift between a transport protocol clock of a host and a monitoring point. The time stamp for each packet is provided by the transport protocol clock of the host. A corrected time stamp for each packet is determined by removing from the scaled time stamp for each respective packet, a temporal offset betweenmore » the transport protocol clock and the monitoring clock by minimizing a temporal delay variation of the plurality of packets traversing a segment between the host and the monitoring point.« less

Do postage stamps versus pre-paid envelopes increase responses to patient mail surveys? A randomised controlled trial.

PubMed

Lavelle, Katrina; Todd, Chris; Campbell, Malcolm

2008-05-28

Studies largely from the market research field suggest that the inclusion of a stamped addressed envelope, rather than a pre-paid business reply, increases the response rate to mail surveys. The evidence that this is also the case regarding patient mail surveys is limited. The aim of this study is to investigate whether stamped addressed envelopes increase response rates to patient mail surveys compared to pre-paid business reply envelopes and compare the relative costs. A sample of 477 initial non-responders to a mail survey of patients attending breast clinics in Greater Manchester between 1/10/2002 - 31/7/2003 were entered into the trial: 239 were randomly allocated to receive a stamped envelope and 238 to receive a pre-paid envelope in with their reminder surveys. Overall cost and per item returned were calculated. The response to the stamped envelope group was 31.8% (95% CI: 25.9% - 37.7%) compared to 26.9% (21.3% - 32.5%) for the pre-paid group. The difference (4.9% 95% CI: -3.3% - 13.1%) is not significant at alpha = 0.05 (chi2 = 1.39; 2 tailed test, d.f. = 1; P = 0.239). The stamped envelopes were cheaper in terms of cost per returned item (1.20 pounds) than the pre-paid envelopes (1.67 pounds). However if the set up cost for the licence to use the pre-paid service is excluded, the cost of the stamped envelopes is more expensive than pre-paid returns (1.20 pounds versus 0.73 pounds). Compared with pre-paid business replies, stamped envelopes did not produce a statistically significant increase in response rate to this patient survey. However, the response gain of the stamped strategy (4.9%) is similar to that demonstrated in a Cochrane review (5.3%) of strategies to increase response to general mail surveys. Further studies and meta analyses of patient responses to mail surveys via stamped versus pre-paid envelopes are needed with sufficient power to detect response gains of this magnitude in a patient population.

Patterning of supported gold monolayers via chemical lift-off lithography

PubMed Central

Slaughter, Liane S; Cheung, Kevin M; Kaappa, Sami; Cao, Huan H; Yang, Qing; Young, Thomas D; Serino, Andrew C; Malola, Sami; Olson, Jana M; Link, Stephan

2017-01-01

The supported monolayer of Au that accompanies alkanethiolate molecules removed by polymer stamps during chemical lift-off lithography is a scarcely studied hybrid material. We show that these Au–alkanethiolate layers on poly(dimethylsiloxane) (PDMS) are transparent, functional, hybrid interfaces that can be patterned over nanometer, micrometer, and millimeter length scales. Unlike other ultrathin Au films and nanoparticles, lifted-off Au–alkanethiolate thin films lack a measurable optical signature. We therefore devised fabrication, characterization, and simulation strategies by which to interrogate the nanoscale structure, chemical functionality, stoichiometry, and spectral signature of the supported Au–thiolate layers. The patterning of these layers laterally encodes their functionality, as demonstrated by a fluorescence-based approach that relies on dye-labeled complementary DNA hybridization. Supported thin Au films can be patterned via features on PDMS stamps (controlled contact), using patterned Au substrates prior to lift-off (e.g., selective wet etching), or by patterning alkanethiols on Au substrates to be reactive in selected regions but not others (controlled reactivity). In all cases, the regions containing Au–alkanethiolate layers have a sub-nanometer apparent height, which was found to be consistent with molecular dynamics simulations that predicted the removal of no more than 1.5 Au atoms per thiol, thus presenting a monolayer-like structure. PMID:29259879

Effects of biosolids and compost amendment on chemistry of soils contaminated with copper from mining activities.

PubMed

Sidhu, Virinder; Sarkar, Dibyendu; Datta, Rupali

2016-03-01

Several million metric tons of mining wastes, called stamp sands, were generated in the Upper Peninsula of Michigan during extensive copper (Cu) mining activities in the past. These materials, containing large amounts of Cu, were discharged into various offshoots of Lake Superior. Due to evidences of Cu toxicity on aquatic organisms, in due course, the materials were dredged and dumped on lake shores, thus converting these areas into vast, fallow lands. Erosion of these Cu-contaminated stamp sands back to the lakes is severely affecting aquatic life. A lack of uniform vegetation cover on stamp sands is facilitating this erosion. Understanding the fact that unless the stamp sands are fertilized to the point of sustaining vegetation growth, the problem with erosion and water quality degradation will continue, amending the stamp sands with locally available biosolids and composts, was considered. The purpose of the reported study was to assess potential effects of such organic fertilizer amendments on soil quality. As the first step of a combined laboratory and greenhouse study, a 2-month-long incubation experiment was performed to investigate the effects of biosolids and compost addition on the soil nutrient profile of stamp sands and organic matter content. Results showed that both biosolids and compost amendments resulted in significant increase in nitrogen and phosphorus concentrations and organic matter contents of stamp sands. Sequential extraction data demonstrated that Cu was mostly present as bound forms in stamp sands, and there was no significant increase in the plant available fraction of Cu because of fertilizer application.

Effect of Al-Si Coating on Weld Microstructure and Properties of 22MnB5 Steel Joints for Hot Stamping

NASA Astrophysics Data System (ADS)

Lin, Wenhu; Li, Fang; Wu, Dongsheng; Chen, Xiaoguan; Hua, Xueming; Pan, Hua

2018-03-01

22MnB5 hot stamping steels are gradually being used in tailor-welded blank applications. In this experiment, 1-mm-thick Al-Si coated and de-coated 22MnB5 steels were laser-welded and then hot-stamped. The chemical compositions, solidification process, microstructure and mechanical properties were investigated to reveal the effect of Al-Si coating and heat treatment. In the welded condition, the coated joints had an Al content of approximately 2.5 wt.% in the fusion zone and the de-coated joints had 0.5 wt.% Al. The aluminum promoted the δ-ferrite formation as the skeletal structure during solidification. In the high-aluminum weld, the microstructure consisted of martensite and long and band-like δ-ferrite. Meanwhile, the low-aluminum weld was full of lath martensite. After the hot stamping process, the δ-ferrite fraction increased from 10 to 24% in the coated joints and the lath martensite became finer in the de-coated joints. The tensile strengths of the coated joints or de-coated joints were similar to that before hot stamping, but the strength of the coated joints was reduced heavily after hot stamping compared to the de-coated joints and base material. The effect of δ-ferrite on the tensile properties became stronger when the fusion zone was soft and deformed first in the hot-stamped specimens. The coated weld showed a brittle fracture surface with many cleavage planes, and the de-coated weld showed a ductile fracture surface with many dimples in hot-stamped conditions.

Application of a dislocation based model for Interstitial Free (IF) steels to typical stamping simulations

NASA Astrophysics Data System (ADS)

Carvalho Resende, T.; Balan, T.; Abed-Meraim, F.; Bouvier, S.; Sablin, S.-S.

2010-06-01

With a view to environmental, economic and safety concerns, car manufacturers need to design lighter and safer vehicles in ever shorter development times. In recent years, High Strength Steels (HSS) like Interstitial Free (IF) steels which have higher ratios of yield strength to elastic modulus, are increasingly used for sheet metal parts in automotive industry to meet the demands. Moreover, the application of sheet metal forming simulations has proven to be beneficial to reduce tool costs in the design stage and to optimize current processes. The Finite Element Method (FEM) is quite successful to simulate metal forming processes but accuracy largely depends on the quality of the material properties provided as input to the material model. Common phenomenological models roughly consist in the fitting of functions on experimental results and do not provide any predictive character for different metals from the same grade. Therefore, the use of accurate plasticity models based on physics would increase predictive capability, reduce parameter identification cost and allow for robust and time-effective finite element simulations. For this purpose, a 3D physically based model at large strain with dislocation density evolution approach was presented in IDDRG2009 by the authors [1]. This model allows the description of work-hardening's behavior for different loading paths (i.e. uni-axial tensile, simple shear and Bauschinger tests) taking into account several data from microstructure (i.e. grain size, texture, etc…). The originality of this model consists in the introduction of microstructure data in a classical phenomenological model in order to achieve work-hardening's predictive character for different metals from the same grade. Indeed, thanks to a microstructure parameter set for an Interstitial Free steel, it is possible to describe work-hardening behavior for different loading paths of other IF steels by only changing the mean grain size and the chemical composition. During sheet metal forming processes local material points may experience multi-axial and multi-path loadings. Before simulating actual industrial parts, automotive manufacturers use validation tools—e.g. the Cross-Die stamping test. Such typical stamping tests enable the evaluation of a complex distribution of strains. The work described is an implementation [2] of a 3D dislocation based model in ABAQUS/Explicit and its validation on a Finite Element (FE) Cross-Die model. In order to assess the performance and relevance of the 3D dislocation based model in the simulation of industrial forming applications, the results of thinning profiles predicted along several directions and the strain distribution were obtained and compared with experimental results for IF steels with grain sizes varying in the 8-22 μm value range.

41 CFR 101-25.103 - Promotional materials, trading stamps, or bonus goods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 41 Public Contracts and Property Management 2 2011-07-01 2007-07-01 true Promotional materials, trading stamps, or bonus goods. 101-25.103 Section 101-25.103 Public Contracts and Property Management... PROCUREMENT 25-GENERAL 25.1-General Policies § 101-25.103 Promotional materials, trading stamps, or bonus...

39 CFR 551.5 - Frequency and other limitations.

Code of Federal Regulations, 2010 CFR

2010-07-01

....C. 416. The 10-year period will commence after the sales period of the Breast Cancer Research stamp is concluded in accordance with the Stamp Out Breast Cancer Act, and as amended by the Semipostal Authorization Act, the Breast Cancer Research Stamp Act of 2001, and Public Law 107-67, section 650, 115 Stat...

Food Stamps and Food Insecurity: What Can Be Learned in the Presence of Nonclassical Measurement Error?

ERIC Educational Resources Information Center

Gundersen, Craig; Kreider, Brent

2008-01-01

Policymakers have been puzzled to observe that food stamp households appear more likely to be food insecure than observationally similar eligible nonparticipating households. We reexamine this issue allowing for nonclassical reporting errors in food stamp participation and food insecurity. Extending the literature on partially identified…

25 CFR 301.1 - Eligibility for use of Government stamp.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 2 2010-04-01 2010-04-01 false Eligibility for use of Government stamp. 301.1 Section 301.1 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR NAVAJO, PUEBLO, AND HOPI SILVER AND TURQUOISE PRODUCTS; STANDARDS § 301.1 Eligibility for use of Government stamp. Subject to the...

Stamp of Approval

ERIC Educational Resources Information Center

Swanson, Joan; Curtis, David

1977-01-01

In an age of exquisite graphic art, perhaps the most universally viewed examples are to be found in the commemorative stamps issued by the Postal Service. At Corona del Mar High School, Newport Beach, California, students cooperated to design a stamp and display their work before the public. They therefore learn how the Postal Service selects a…

39 CFR 551.5 - Frequency and other limitations.

Code of Federal Regulations, 2011 CFR

2011-07-01

....C. 416. The 10-year period will commence after the sales period of the Breast Cancer Research stamp is concluded in accordance with the Stamp Out Breast Cancer Act, and as amended by the Semipostal Authorization Act, the Breast Cancer Research Stamp Act of 2001, and Public Law 107-67, section 650, 115 Stat...

76 FR 66609 - Airworthiness Directives; Bell Helicopter Textron Canada (Bell) Model 407 and 427 Helicopters

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-27

... surface. The AD also requires reidentifying the servo by metal-impression stamping or by vibro- etching... surface. The AD also requires reidentifying the servo by metal-impression stamping or by vibro-etching... metal-impression stamping or by vibro-etching ``67.01'' onto the modification plate. Before installing a...

Internet-Based Training to Improve Preschool Playground Safety: Evaluation of the Stamp-in-Safety Programme

ERIC Educational Resources Information Center

Schwebel, David C.; Pennefather, Jordan; Marquez, Brion; Marquez, Jessie

2015-01-01

Objective: Playground injuries result in over 200,000 US pediatric emergency department visits annually. One strategy to reduce injuries is improved adult supervision. The Stamp-in-Safety programme, which involves supervisors stamping rewards for children playing safely, has been demonstrated in preliminary classroom-based work to reduce child…

41 CFR 101-25.103 - Promotional materials, trading stamps, or bonus goods.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 41 Public Contracts and Property Management 2 2014-07-01 2012-07-01 true Promotional materials, trading stamps, or bonus goods. 101-25.103 Section 101-25.103 Public Contracts and Property Management... PROCUREMENT 25-GENERAL 25.1-General Policies § 101-25.103 Promotional materials, trading stamps, or bonus...

41 CFR 101-25.103 - Promotional materials, trading stamps, or bonus goods.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 41 Public Contracts and Property Management 2 2013-07-01 2012-07-01 true Promotional materials, trading stamps, or bonus goods. 101-25.103 Section 101-25.103 Public Contracts and Property Management... PROCUREMENT 25-GENERAL 25.1-General Policies § 101-25.103 Promotional materials, trading stamps, or bonus...

41 CFR 101-25.103 - Promotional materials, trading stamps, or bonus goods.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 41 Public Contracts and Property Management 2 2012-07-01 2012-07-01 false Promotional materials, trading stamps, or bonus goods. 101-25.103 Section 101-25.103 Public Contracts and Property Management... PROCUREMENT 25-GENERAL 25.1-General Policies § 101-25.103 Promotional materials, trading stamps, or bonus...

39 CFR 551.5 - Frequency and other limitations.

Code of Federal Regulations, 2012 CFR

2012-07-01

....C. 416. The 10-year period will commence after the sales period of the Breast Cancer Research stamp is concluded in accordance with the Stamp Out Breast Cancer Act, and as amended by the Semipostal Authorization Act, the Breast Cancer Research Stamp Act of 2001, and Public Law 107-67, section 650, 115 Stat...

39 CFR 551.5 - Frequency and other limitations.

Code of Federal Regulations, 2014 CFR

2014-07-01

....C. 416. The 10-year period will commence after the sales period of the Breast Cancer Research stamp is concluded in accordance with the Stamp Out Breast Cancer Act, and as amended by the Semipostal Authorization Act, the Breast Cancer Research Stamp Act of 2001, and Public Law 107-67, section 650, 115 Stat...

39 CFR 551.5 - Frequency and other limitations.

Code of Federal Regulations, 2013 CFR

2013-07-01

....C. 416. The 10-year period will commence after the sales period of the Breast Cancer Research stamp is concluded in accordance with the Stamp Out Breast Cancer Act, and as amended by the Semipostal Authorization Act, the Breast Cancer Research Stamp Act of 2001, and Public Law 107-67, section 650, 115 Stat...

26 CFR 301.6805-1 - Redemption of stamps.

Code of Federal Regulations, 2010 CFR

2010-04-01

... of the service center within three years from the date of the purchase of the stamps from the... where the actual date of purchase of the stamps from the Government cannot be established, it must be definitely shown in the claim whether they were so purchased within three years prior to the date of filing...

41 CFR 101-25.103 - Promotional materials, trading stamps, or bonus goods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Promotional materials, trading stamps, or bonus goods. 101-25.103 Section 101-25.103 Public Contracts and Property Management... PROCUREMENT 25-GENERAL 25.1-General Policies § 101-25.103 Promotional materials, trading stamps, or bonus...

Does the Timing of Food Stamp Distribution Matter? A Panel-Data Analysis of Monthly Purchasing Patterns of US Households.

PubMed

Castellari, Elena; Cotti, Chad; Gordanier, John; Ozturk, Orgul

2017-11-01

In this paper, we examine the relationship between the timing of food stamp receipt and purchasing patterns. We combine data on state distribution dates of food stamps with scanner data on a panel of households purchases tracked between 2004 and 2011. We find that purchases of a variety of goods are meaningfully higher on receipt days, consistent with previous work that suggests that recipients are very impatient. Additionally, and importantly, estimates indicate that when food stamp receipt days fall on weekends, total monthly purchases within the same households are affected. In particular, monthly purchases of beer are higher when food stamps are distributed on a weekend rather than in months where benefits are distributed on weekdays. For these households, total beer purchases are between 4 and 5% higher in those months. Among households ineligible for food stamps, no effect is identified. These results demonstrate that the 'day-of-the-week' of SNAP treatment may have important impacts on household purchase habits. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Use of atomic force microscopy in the forensic application of chronological order of toners and stamping inks in questioned documents.

PubMed

Kang, Tae-Yi; Lee, Joong; Park, Byung-Wook

2016-04-01

This paper describes the application of the atomic force microscopy (AFM) as a nano-indentation method and introduces a new method of identifying the chronological order of the application of the toner and stamping ink on the surface of documents by removing either of them. Various toners were used as samples for the AFM nano-indentation method. The chronological order of the application of the toner and stamping ink with either the toner placed over the stamping ink or the stamping ink placed over the toner, could be identified, regardless of the kinds of toners made by various companies. This paper provides the new approach for physically removing the toner and checking the material below it to identify questioned documents, which allows the method to be used to appraise documents forensically. Blind testing has shown that the method to analyze the chronological order of toner-printed documents and the seal stamping on them could accurately identify the order in all samples, while minimizing damage to the samples. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Visualization of the Invisible, Explanation of the Unknown, Ruggedization of the Unstable: Sensitivity Analysis, Virtual Tryout and Robust Design through Systematic Stochastic Simulation

NASA Astrophysics Data System (ADS)

Zwickl, Titus; Carleer, Bart; Kubli, Waldemar

2005-08-01

In the past decade, sheet metal forming simulation became a well established tool to predict the formability of parts. In the automotive industry, this has enabled significant reduction in the cost and time for vehicle design and development, and has helped to improve the quality and performance of vehicle parts. However, production stoppages for troubleshooting and unplanned die maintenance, as well as production quality fluctuations continue to plague manufacturing cost and time. The focus therefore has shifted in recent times beyond mere feasibility to robustness of the product and process being engineered. Ensuring robustness is the next big challenge for the virtual tryout / simulation technology. We introduce new methods, based on systematic stochastic simulations, to visualize the behavior of the part during the whole forming process — in simulation as well as in production. Sensitivity analysis explains the response of the part to changes in influencing parameters. Virtual tryout allows quick exploration of changed designs and conditions. Robust design and manufacturing guarantees quality and process capability for the production process. While conventional simulations helped to reduce development time and cost by ensuring feasible processes, robustness engineering tools have the potential for far greater cost and time savings. Through examples we illustrate how expected and unexpected behavior of deep drawing parts may be tracked down, identified and assigned to the influential parameters. With this knowledge, defects can be eliminated or springback can be compensated e.g.; the response of the part to uncontrollable noise can be predicted and minimized. The newly introduced methods enable more reliable and predictable stamping processes in general.

19. DETAIL OF STAMP BATTERY AUTOMATIC FEEDER, LOOKING EAST. THIS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

19. DETAIL OF STAMP BATTERY AUTOMATIC FEEDER, LOOKING EAST. THIS IS THE MIDDLE OF THREE FEEDERS, ONE FOR EACH STAMP BATTERY. THE CHUTE (UPPER RIGHT) INTRODUCED THE CRUSHED ORE FROM THE ORE BIN. FLOW WAS CONTROLLED BY A SLIDING DOOR ON THE UPPER LEVEL. - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

Literature review of tufted reinforcement for composite structures

NASA Astrophysics Data System (ADS)

Gnaba, I.; Legrand, X.; Wang, P.; Soulat, D.

2017-10-01

In order to minimize the damage caused by the 2D structures, several research have been done on more complex structures (3D-preforms) which have more interesting mechanical characteristics. Divers textile technologies are used to manufacture 3D preforms such as weaving, knitting, stitching, z-pinning, tufting… This kind of reinforcement aims to achieve a balance between the in-plane and out-of-plane properties. Recently, the tufting technology shows more opportunities to develop 3D reinforcements especially with the advances in robotics. The present paper focuses not only on the various technologies of reinforcement through the thickness but also on the mechanical behaviour of a tufted preform in a stamping process.

Has your ancient stamp been regummed with synthetic glue? A FT-NIR and FT-Raman study.

PubMed

Simonetti, Remo; Oliveri, Paolo; Henry, Adrien; Duponchel, Ludovic; Lanteri, Silvia

2016-01-01

The potential of FT-NIR and FT-Raman spectroscopies to characterise the gum applied on the backside of ancient stamps was investigated for the first time. This represents a very critical issue for the collectors' market, since gum conditions heavily influence stamp quotations, and fraudulent application of synthetic gum onto damaged stamp backsides to increase their desirability is a well-documented practice. Spectral data were processed by exploratory pattern recognition tools. In particular, application of principal component analysis (PCA) revealed that both of the spectroscopic techniques provide information useful to characterise stamp gum. Examination of PCA loadings and their chemical interpretation confirmed the robustness of the outcomes. Fusion of FT-NIR and FT-Raman spectral data was performed, following both a low-level and a mid-level procedure. The results were critically compared with those obtained separately for the two spectroscopic techniques. Copyright © 2015 Elsevier B.V. All rights reserved.

Design for testability and diagnosis at the system-level

NASA Technical Reports Server (NTRS)

Simpson, William R.; Sheppard, John W.

1993-01-01

The growing complexity of full-scale systems has surpassed the capabilities of most simulation software to provide detailed models or gate-level failure analyses. The process of system-level diagnosis approaches the fault-isolation problem in a manner that differs significantly from the traditional and exhaustive failure mode search. System-level diagnosis is based on a functional representation of the system. For example, one can exercise one portion of a radar algorithm (the Fast Fourier Transform (FFT) function) by injecting several standard input patterns and comparing the results to standardized output results. An anomalous output would point to one of several items (including the FFT circuit) without specifying the gate or failure mode. For system-level repair, identifying an anomalous chip is sufficient. We describe here an information theoretic and dependency modeling approach that discards much of the detailed physical knowledge about the system and analyzes its information flow and functional interrelationships. The approach relies on group and flow associations and, as such, is hierarchical. Its hierarchical nature allows the approach to be applicable to any level of complexity and to any repair level. This approach has been incorporated in a product called STAMP (System Testability and Maintenance Program) which was developed and refined through more than 10 years of field-level applications to complex system diagnosis. The results have been outstanding, even spectacular in some cases. In this paper we describe system-level testability, system-level diagnoses, and the STAMP analysis approach, as well as a few STAMP applications.

Postage stamp-sized array sensor for the sensitive screening test of heavy-metal ions.

PubMed

Zhang, Yu; Li, Xiao; Li, Hui; Song, Ming; Feng, Liang; Guan, Yafeng

2014-10-07

The sensitive determination of heavy-metal ions has been widely investigated in recent years due to their threat to the environment and to human health. Among various analytical detection techniques, inexpensive colorimetric testing papers/strips play a very important role. The limitation, however, is also clear: the sensitivity is usually low and the selectivity is poor. In this work, we have developed a postage stamp-sized array sensor composed of nine commercially available heterocyclic azo indicators. Combining filtration-based enrichment with an array of technologies-based pattern-recognition, we have obtained the discrimination capability for seven heavy-metal ions (Hg(2+), Pb(2+), Ag(+), Ni(2+), Cu(2+), Zn(2+), and Co(2+)) at their Chinese wastewater discharge standard concentrations. The allowable detection level of Hg(2+) was down to 0.05 mg L(-1). The heavy-metal ions screening test was readily achieved using a standard chemometric approach. And the array sensor applied well in real water samples.

Reagent- and separation-free measurements of urine creatinine concentration using stamping surface enhanced Raman scattering (S-SERS)

PubMed Central

Li, Ming; Du, Yong; Zhao, Fusheng; Zeng, Jianbo; Mohan, Chandra; Shih, Wei-Chuan

2015-01-01

We report a novel reagent- and separation-free method for urine creatinine concentration measurement using stamping surface enhanced Raman scattering (S-SERS) technique with nanoporous gold disk (NPGD) plasmonic substrates, a label-free, multiplexed molecular sensing and imaging technique recently developed by us. The performance of this new technology is evaluated by the detection and quantification of creatinine spiked in three different liquids: creatinine in water, mixture of creatinine and urea in water, and creatinine in artificial urine within physiologically relevant concentration ranges. Moreover, the potential application of our method is demonstrated by creatinine concentration measurements in urine samples collected from a mouse model of nephritis. The limit of detection of creatinine was 13.2 nM (0.15 µg/dl) and 0.68 mg/dl in water and urine, respectively. Our method would provide an alternative tool for rapid, cost-effective, and reliable urine analysis for non-invasive diagnosis and monitoring of renal function. PMID:25798309

27 CFR 46.116 - Issuance, distribution, and examination of special tax stamps.

Code of Federal Regulations, 2011 CFR

2011-04-01

... multiple locations, TTB will send to the taxpayer's principal place of business (or principal office in the... attachment to TTB Form 5630.5t required by § 46.101(b)(2). (b) Distribution of special tax stamps for... for each location listed on the attachment to TTB Form 5630.5t and that the information on each stamp...

27 CFR 46.116 - Issuance, distribution, and examination of special tax stamps.

Code of Federal Regulations, 2010 CFR

2010-04-01

... multiple locations, TTB will send to the taxpayer's principal place of business (or principal office in the... attachment to TTB Form 5630.5t required by § 46.101(b)(2). (b) Distribution of special tax stamps for... for each location listed on the attachment to TTB Form 5630.5t and that the information on each stamp...

Evaluation of Contact Heat Transfer Coefficient and Phase Transformation during Hot Stamping of a Hat-Type Part

PubMed Central

Kim, Heung-Kyu; Lee, Seong Hyeon; Choi, Hyunjoo

2015-01-01

Using an inverse analysis technique, the heat transfer coefficient on the die-workpiece contact surface of a hot stamping process was evaluated as a power law function of contact pressure. This evaluation was to determine whether the heat transfer coefficient on the contact surface could be used for finite element analysis of the entire hot stamping process. By comparing results of the finite element analysis and experimental measurements of the phase transformation, an evaluation was performed to determine whether the obtained heat transfer coefficient function could provide reasonable finite element prediction for workpiece properties affected by the hot stamping process. PMID:28788046

[The stamp technique for direct composite restoration].

PubMed

Perrin, Philippe; Zimmerli, Brigitte; Jacky, Daniel; Lussi, Adrian; Helbling, Christoph; Ramseyer, Simon

2013-01-01

The indications for direct resin composite restorations are nowadays extended due to the development of modern resin materials with improved material properties. However, there are still some difficulties regarding handling of resin composite material, especially in large restorations. The reconstruction of a functional and individual occlusion is difficult to achieve with direct application techniques. The aim of the present publication was to introduce a new "stamp"-technique for placing large composite restorations. The procedure of this "stamp"-technique is presented by three typical indications: large single-tooth restoration, occlusal rehabilitation of a compromised occlusal surface due to erosions and direct fibre-reinforced fixed partial denture. A step-by-step description of the technique and clinical figures illustrates the method. Large single-tooth restorations can be built-up with individual, two- piece silicone stamps. Large occlusal abrasive and/or erosive defects can be restored by copying the wax-up from the dental technician using the "stamp"-technique. Even fiber-reinforced resin-bonded fixed partial dentures can be formed with this intraoral technique with more precision and within a shorter treatment time. The presented "stamp"-technique facilitates the placement of large restoration with composite and can be recommended for the clinical use.

Audio signal analysis for tool wear monitoring in sheet metal stamping

NASA Astrophysics Data System (ADS)

Ubhayaratne, Indivarie; Pereira, Michael P.; Xiang, Yong; Rolfe, Bernard F.

2017-02-01

Stamping tool wear can significantly degrade product quality, and hence, online tool condition monitoring is a timely need in many manufacturing industries. Even though a large amount of research has been conducted employing different sensor signals, there is still an unmet demand for a low-cost easy to set up condition monitoring system. Audio signal analysis is a simple method that has the potential to meet this demand, but has not been previously used for stamping process monitoring. Hence, this paper studies the existence and the significance of the correlation between emitted sound signals and the wear state of sheet metal stamping tools. The corrupting sources generated by the tooling of the stamping press and surrounding machinery have higher amplitudes compared to that of the sound emitted by the stamping operation itself. Therefore, a newly developed semi-blind signal extraction technique was employed as a pre-processing technique to mitigate the contribution of these corrupting sources. The spectral analysis results of the raw and extracted signals demonstrate a significant qualitative relationship between wear progression and the emitted sound signature. This study lays the basis for employing low-cost audio signal analysis in the development of a real-time industrial tool condition monitoring system.

Electrostatic force assisted deposition of graphene

DOEpatents

Liang, Xiaogan [Berkeley, CA

2011-11-15

An embodiment of a method of depositing graphene includes bringing a stamp into contact with a substrate over a contact area. The stamp has at least a few layers of the graphene covering the contact area. An electric field is developed over the contact area. The stamp is removed from the vicinity of the substrate which leaves at least a layer of the graphene substantially covering the contact area.

45 CFR 261.31 - How many hours must a work-eligible individual participate for the family to count in the...

Code of Federal Regulations, 2011 CFR

2011-10-01

...; education directly related to employment; and satisfactory attendance at secondary school or in a course of... Simplified Food Stamp Program option that permits a State to count the value of food stamps in determining... does not have a traditional Food Stamp Program, to deem core hours, it must include the value of food...

46 CFR 52.01-140 - Certification by stamping (modifies PG-104 through PG-113).

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Certification by stamping (modifies PG-104 through PG-113). 52.01-140 Section 52.01-140 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING POWER BOILERS General Requirements § 52.01-140 Certification by stamping (modifies PG-104 through PG-113). (a) All boilers built in...

46 CFR 52.01-140 - Certification by stamping (modifies PG-104 through PG-113).

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Certification by stamping (modifies PG-104 through PG-113). 52.01-140 Section 52.01-140 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING POWER BOILERS General Requirements § 52.01-140 Certification by stamping (modifies PG-104 through PG-113). (a) All boilers built in...

46 CFR 52.01-140 - Certification by stamping (modifies PG-104 through PG-113).

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Certification by stamping (modifies PG-104 through PG-113). 52.01-140 Section 52.01-140 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING POWER BOILERS General Requirements § 52.01-140 Certification by stamping (modifies PG-104 through PG-113). (a) All boilers built in...

46 CFR 52.01-140 - Certification by stamping (modifies PG-104 through PG-113).

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Certification by stamping (modifies PG-104 through PG-113). 52.01-140 Section 52.01-140 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING POWER BOILERS General Requirements § 52.01-140 Certification by stamping (modifies PG-104 through PG-113). (a) All boilers built in...

46 CFR 52.01-140 - Certification by stamping (modifies PG-104 through PG-113).

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Certification by stamping (modifies PG-104 through PG-113). 52.01-140 Section 52.01-140 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING POWER BOILERS General Requirements § 52.01-140 Certification by stamping (modifies PG-104 through PG-113). (a) All boilers built in...

16. OBLIQUE DETAIL VIEW OF STAMP BATTERIES AND APRONS, LOOKING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

16. OBLIQUE DETAIL VIEW OF STAMP BATTERIES AND APRONS, LOOKING SOUTHWEST. EACH BATTERY CONTAINS FIVE STAMPS. TWO OF THE THREE BATTERIES ARE SIDE BY SIDE IN FOREGROUND, WHILE THE THIRD BATTERY IS SEPARATE (LOWER RIGHT). STAIRWAY UP IS AT LEFT SIDE. SEE CA-290-43 (CT) FOR IDENTICAL COLOR TRANSPARENCY. - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

43. OBLIQUE DETAIL VIEW OF STAMP BATTERIES AND APRONS, LOOKING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

43. OBLIQUE DETAIL VIEW OF STAMP BATTERIES AND APRONS, LOOKING SOUTHWEST. EACH BATTERY CONTAINS FIVE STAMPS. TWO OF THE THREE BATTERIES ARE SIDE BY SIDE IN FOREGROUND, WHILE THE THIRD BATTERY IS SEPARATE (LOWER RIGHT). STAIRWAY UP IS AT LEFT SIDE. SEE CA-290-16 FOR IDENTICAL B&W NEGATIVE. - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

2007 Program of Study: Boundary Layers

DTIC Science & Technology

2008-06-01

Compressible Fluid: 3He near Tc. Phys. Rev. Let. 82, 4635-4638. [13] Onuki , A., Hao, H ., and Ferrell, R. A. 1990 Fast adiabatic equilibration in a...Supérieure H . Joseph Fernando Arizona State University Glenn Flierl Massachusetts Institute of Technology Rockwell Geyer Woods Hole Oceanographic...which is controlled by the free fluid, yet which in turn give the free movement its characteristic stamp by the emission of vortex sheets. ( H . Rouse and S

Sensitivity Analysis of the Sheet Metal Stamping Processes Based on Inverse Finite Element Modeling and Monte Carlo Simulation

NASA Astrophysics Data System (ADS)

Yu, Maolin; Du, R.

2005-08-01

Sheet metal stamping is one of the most commonly used manufacturing processes, and hence, much research has been carried for economic gain. Searching through the literatures, however, it is found that there are still a lots of problems unsolved. For example, it is well known that for a same press, same workpiece material, and same set of die, the product quality may vary owing to a number of factors, such as the inhomogeneous of the workpice material, the loading error, the lubrication, and etc. Presently, few seem able to predict the quality variation, not to mention what contribute to the quality variation. As a result, trial-and-error is still needed in the shop floor, causing additional cost and time delay. This paper introduces a new approach to predict the product quality variation and identify the sensitive design / process parameters. The new approach is based on a combination of inverse Finite Element Modeling (FEM) and Monte Carlo Simulation (more specifically, the Latin Hypercube Sampling (LHS) approach). With an acceptable accuracy, the inverse FEM (also called one-step FEM) requires much less computation load than that of the usual incremental FEM and hence, can be used to predict the quality variations under various conditions. LHS is a statistical method, through which the sensitivity analysis can be carried out. The result of the sensitivity analysis has clear physical meaning and can be used to optimize the die design and / or the process design. Two simulation examples are presented including drawing a rectangular box and drawing a two-step rectangular box.

Mercury MESSENGER Stamp Unveiling

NASA Image and Video Library

2011-05-03

United States Postal Service Vice President of Finance Steve Masse, left, and NASA Mercury Astronaut Scott Carpenter, unveil two USPS stamps to commemorate and celebrate 50 years of US Spaceflight and the MESSENGER program during an event, Wednesday, May 4, 2011 at the NASA Kennedy Space Center in Cape Canaveral, Fla. One stamp commemorates NASA’s Project Mercury, America’s first manned spaceflight program, and NASA astronaut Alan Shepard’s historic flight on May 5, 1961, aboard spacecraft Freedom 7. The other stamp draws attention to NASA’s unmanned MESSENGER mission, a scientific investigation of the planet Mercury. On March 17, 2011, MESSENGER became the first spacecraft to enter into orbit around Mercury. Photo Credit: (NASA/Bill Ingalls)

39. CLOSE UP DETAIL OF THE FEEDER AND STAMP CONNECTION. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

39. CLOSE UP DETAIL OF THE FEEDER AND STAMP CONNECTION. THE STAMP AN MORTAR BOX ARE ON THE LEFT AND THE FEEDER WITH ITS FEEDER DISK IS ON THE RIGHT. NOTE THE COLLAR ON THE CENTER STAMP STEM (UPPER LEFT CORNER OF THE IMAGE) THAT ACTIVATES THE LEVER IN THE CENTER OF THE PHOTO. THE COLLAR IS POSITIONED SUCH THAT WHEN THE LEVEL OF THE MATERIAL REACHES A LOW POINT IN THE MORTAR BOX IT PUSHES DOWN ON THE LEVER WHICH IN TURN ACTIVATES THE AUTOMATIC FEEDER DRIVE MECHANISM WHICH THEM DELIVERS ORE INTO THE BACKSIDE OF THE MORTAR BOX. - Standard Gold Mill, East of Bodie Creek, Northeast of Bodie, Bodie, Mono County, CA

Mercury MESSENGER Stamp Unveiling

NASA Image and Video Library

2011-05-03

Daughters of NASA astronaut Alan Shepard, Laura Shepard Churchley, left, Alice Wackermann and Julie Jenkins, right, speak during an unveiling ceremony of two USPS stamps that commemorate and celebrate 50 years of US Spaceflight and the MESSENGER program during an event, Wednesday, May 4, 2011 at the NASA Kennedy Space Center in Cape Canaveral, Fla. One stamp commemorates NASA’s Project Mercury, America’s first manned spaceflight program, and NASA astronaut Alan Shepard’s historic flight on May 5, 1961, aboard spacecraft Freedom 7. The other stamp draws attention to NASA’s unmanned MESSENGER mission, a scientific investigation of the planet Mercury. On March 17, 2011, MESSENGER became the first spacecraft to enter into orbit around Mercury. Photo Credit: (NASA/Bill Ingalls)

Integrating GIS and ABM to Explore Spatiotemporal Dynamics

NASA Astrophysics Data System (ADS)

Sun, M.; Jiang, Y.; Yang, C.

2013-12-01

Agent-based modeling as a methodology for the bottom-up exploration with the account of adaptive behavior and heterogeneity of system components can help discover the development and pattern of the complex social and environmental system. However, ABM is a computationally intensive process especially when the number of system components becomes large and the agent-agent/agent-environmental interaction is modeled very complex. Most of traditional ABM frameworks developed based on CPU do not have a satisfying computing capacity. To address the problem and as the emergence of advanced techniques, GPU computing with CUDA can provide powerful parallel structure to enable the complex simulation of spatiotemporal dynamics. In this study, we first develop a GPU-based ABM system. Secondly, in order to visualize the dynamics generated from the movement of agent and the change of agent/environmental attributes during the simulation, we integrate GIS into the ABM system. Advanced geovisualization technologies can be utilized for representing the spatiotemporal change events, such as proper 2D/3D maps with state-of-the-art symbols, space-time cube and multiple layers each of which presents pattern in one time-stamp, etc. Thirdly, visual analytics which include interactive tools (e.g. grouping, filtering, linking, etc.) is included in our ABM-GIS system to help users conduct real-time data exploration during the progress of simulation. Analysis like flow analysis and spatial cluster analysis can be integrated according to the geographical problem we want to explore.

POLYELECTROLYTE MULTILAYER STAMPING IN AQUEOUS PHASE AND NON-CONTACT MODE

PubMed Central

Mehrotra, Sumit; Lee, Ilsoon; Liu, Chun; Chan, Christina

2011-01-01

Polyelectrolyte multilayer (PEM) transfer printing has been previously achieved by stamping under dry conditions. Here, we show for the first time, that PEM can be transferred from a stamp to the base substrate under aqueous conditions whereby the two surfaces are in a non-contact mode. Degradable multilayers of (PAA/PEG)10.5 followed by non-degradable multilayers of (PDAC/SPS)80.5 were fabricated under acidic pH conditions on either PDMS or glass (stamp), and subsequently transferred over top of another multilayer prepared on a different substrate (base substrate), with a spacing of ~ 200 μm between the stamping surface and the base substrate. This multilayer transfer was performed under physiological pH conditions. This process is referred to herein as non-contact, aqueous-phase multilayer (NAM) transfer. NAM transfer can be useful for applications such as fabricating three-dimensional (3-D) cellular scaffolds. We attempted to create a 3-D cellular scaffold using NAM transfer, and characterized the scaffolds with conventional and fluorescence microscopy. PMID:21860540

A mail survey of United States hematologists and oncologists: a comparison of business reply versus stamped return envelopes.

PubMed

Streiff, M B; Dundes, L; Spivak, J L

2001-04-01

Mailed surveys are a popular means of obtaining data on large populations. In July 1999 a mail survey was conducted among 3000 randomly selected members of the American Society of Hematology to assess their approach to diagnosis and treatment of polycythemia vera. Because the researchers and the study population are members of the same professional organization with a vested interest in the results, we anticipated that the advantages of return stamped postage seen in previous studies would be less significant. The response rate for stamped return envelopes was 38% versus 32% for business reply envelopes. This statistically significant difference (P =.0005) of six percentage points is comparable to previous research. Excluding labor, the total cost per returned survey was $2.62 for business reply envelopes versus $1.82 for stamped return envelopes. We conclude that stamped return envelopes are a more effective and cost-efficient means of procuring data from physician specialists.

The Adoption of Electronic Benefit Transfer Card for Delivering Food Stamp Benefits in Alabama: Perceptions of College Students Participating in the Food Stamp Program

ERIC Educational Resources Information Center

Zekeri, Andrew A.

2004-01-01

The reasons for moving from paper coupons to delivering food stamps electronically include potential reduction in the cost of administering the system and in fraud, theft and abuse of the system. Furthermore, the use of EBT is believed o reduce social stigma and embarrassment felt by recipients when using paper coupon. Therefore, using survey data…

Women Putting Our Stamp on America: Biographies and Activities for National Women's History Month, March 1999.

ERIC Educational Resources Information Center

National Women's History Project, Windsor, CA.

This booklet, intended for use by educators and by workplace and community organizers, introduces women who have been featured on U.S. postage stamps as well as a few of the women who clearly merit such honor in the future. Postage stamps featuring women have been relatively few and far between and have only skimmed the surface of U.S. women in…

Can laboratory and pilot recycling trials predict adhesive removal in commercial recycling systems? : results from the USPS environmentally benign stamp project

Treesearch

Carl Houtman; Daniel Seiter; Nancy Ross Sutherland; Donald Donermeyer

2002-01-01

The ultimate goal of the US Postal Service (USPS) Environmentally Benign Stamp Program is to develop stamp laminates, i.e., face paper, adhesive and siliconized liner, that do not cause difficulties in recycling mills. The criterion for success, and the USPS definition of benignity, is the avoidance of process and product quality hardships when such PSA laminates are...

Chlorine condenser-evaporator simulation

NASA Astrophysics Data System (ADS)

Muraveva, E. A.

2017-10-01

Refrigeration machines are an integral part of chemical engineering. Coldness in mechanical engineering is used to improve the properties of steels, to stabilize the shape and size of steel parts, to restore the dimensions of worn steel hardened parts, to fasten the parts to be machined during cutting and grinding, to ensure fixed planting during assembly, bending pipelines, deep drawing and stamping parts from sheet materials, in the manufacture and processing of rubber parts, with solid anodizing of aluminum alloy parts.

Information Foraging Theory in Software Maintenance

DTIC Science & Technology

2012-09-30

classified information, stamp classification level on the top and bottom of this page. 17. LIMITATION OF ABSTRACT. This block must be completed to assign a ...time: for example a time series plot of model reaction times to many (simulated) stimuli presented to it in a run • “ Statistical ” abstractions summed...shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number

A concurrent resolution expressing the sense of Congress that a postage stamp should be issued to commemorate the War of 1812 and that the Citizens' Stamp Advisory Committee should recommend to the Postmaster General that such a stamp be issued.

THOMAS, 111th Congress

Sen. Levin, Carl [D-MI

2009-10-05

Senate - 10/19/2009 Committee on Homeland Security and Governmental Affairs referred to Subcommittee on Federal Financial Management, Government Information, Federal Services, and International Security. (All Actions) Tracker: This bill has the status IntroducedHere are the steps for Status of Legislation:

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lyu, Sungnam, E-mail: blueden@postech.ac.kr; Hwang, Woonbong, E-mail: whwang@postech.ac.kr

Patterning techniques are essential to many research fields such as chemistry, biology, medicine, and micro-electromechanical systems. In this letter, we report a simple, fast, and low-cost superhydrophobic patterning method using a superhydrophilic template. The technique is based on the contact stamping of the surface during hydrophobic dip coating. Surface characteristics were measured using scanning electron microscopy and energy-dispersive X-ray spectroscopic analysis. The results showed that the hydrophilic template, which was contacted with the stamp, was not affected by the hydrophobic solution. The resolution study was conducted using a stripe shaped stamp. The patterned line was linearly proportional to the widthmore » of the stamp line with a constant narrowing effect. A surface with regions of four different types of wetting was fabricated to demonstrate the patterning performance.« less

Prices of unhealthy foods, Food Stamp Program participation, and body weight status among U.S. low-income women.

PubMed

Zhang, Qi; Chen, Zhuo; Diawara, Norou; Wang, Youfa

2011-06-01

This paper examines the interactive effect between the price of unhealthy foods and Food Stamp Program participation on body weight status among low-income women in the United States. We merged the panel data of the National Longitudinal Survey of Youth 1979 cohort in 1985-2002 and the Cost of Living Index data compiled by the American Chamber of Commerce Researchers Association by using geographic identifiers. Using the merged data, we used panel econometric models to examine the impact of unhealthy food prices on the food stamp-eligible U.S. population. Our results indicate that higher prices for unhealthy food can partially offset the positive association between Food Stamp Program participation and bodyweight among low-income women.

Mercury MESSENGER Stamp Unveiling

NASA Image and Video Library

2011-05-03

Daughters of NASA astronaut Alan Shepard, Laura Shepard Churchley, standing left, Alice Wackermann and Julie Jenkins, standing right, speak during an unveiling ceremony of two USPS stamps that commemorate and celebrate 50 years of US Spaceflight and the MESSENGER program during an event, Wednesday, May 4, 2011 at the NASA Kennedy Space Center in Cape Canaveral, Fla. One stamp commemorates NASA’s Project Mercury, America’s first manned spaceflight program, and NASA astronaut Alan Shepard’s historic flight on May 5, 1961, aboard spacecraft Freedom 7. The other stamp draws attention to NASA’s unmanned MESSENGER mission, a scientific investigation of the planet Mercury. On March 17, 2011, MESSENGER became the first spacecraft to enter into orbit around Mercury. Photo Credit: (NASA/Bill Ingalls)

Synchronous Parallel Emulation and Discrete Event Simulation System with Self-Contained Simulation Objects and Active Event Objects

NASA Technical Reports Server (NTRS)

Steinman, Jeffrey S. (Inventor)

1998-01-01

The present invention is embodied in a method of performing object-oriented simulation and a system having inter-connected processor nodes operating in parallel to simulate mutual interactions of a set of discrete simulation objects distributed among the nodes as a sequence of discrete events changing state variables of respective simulation objects so as to generate new event-defining messages addressed to respective ones of the nodes. The object-oriented simulation is performed at each one of the nodes by assigning passive self-contained simulation objects to each one of the nodes, responding to messages received at one node by generating corresponding active event objects having user-defined inherent capabilities and individual time stamps and corresponding to respective events affecting one of the passive self-contained simulation objects of the one node, restricting the respective passive self-contained simulation objects to only providing and receiving information from die respective active event objects, requesting information and changing variables within a passive self-contained simulation object by the active event object, and producing corresponding messages specifying events resulting therefrom by the active event objects.

Analysis, Simulation and Prediction of Cosmetic Defects on Automotive External Panel

NASA Astrophysics Data System (ADS)

Le Port, A.; Thuillier, S.; Borot, C.; Charbonneaux, J.

2011-08-01

The first feeling of quality for a vehicle is linked to its perfect appearance. This has a major impact on the reputation of a car manufacturer. Cosmetic defects are thus more and more taken into account in the process design. Qualifying a part as good or bad from the cosmetic point of view is mainly subjective: the part aspect is considered acceptable if no defect is visible on the vehicle by the final customer. Cosmetic defects that appear during sheet metal forming are checked by visual inspection in light inspection rooms, stoning, or with optical or mechanical sensors or feelers. A lack of cosmetic defect prediction before part production leads to the need for corrective actions, production delays and generates additional costs. This paper first explores the objective description of what cosmetic defects are on a stamped part and where they come from. It then investigates the capability of software to predict these defects, and suggests the use of a cosmetic defects analysis tool developed within PAM-STAMP 2G for its qualitative and quantitative prediction.

The LAAS network observation for studying time correlations in extensive air showers

NASA Astrophysics Data System (ADS)

Ochi, Nobuaki; Iyono, A.; Kimura, Hitoomi; Konishi, Takeharu; Nakamura, Toru; Nakatsuka, Takao; Ohara, Soji; Ohmori, Nobuharu; Saito, Katsuhiko; Takahashi, Nobusuke; Tsuji, Shuhei; Wada, Tomonori; Yamamoto, Isao; Yamashita, Yoshihiko; Yanagimoto, Yukio

2003-02-01

The Large Area Air Shower (LAAS) group has been performing a network observation of extensive air showers (EAS) since 1996 in Japan. Ten compact EAS arrays are operating simultaneously at distant stations (up to ≍1000 km) and detecting EAS with mean energy of ≍1015 eV. Each station has 4--12 scintillation counters and a Global Positioning System (GPS), which provides time stamps of EAS triggers with an accuracy of 1μs. As a consequence of the comparable time stamps, uniformly-adjusted detectors and a standardized data format among all stations, we can treat the independent observations as a gigantic EAS detector system as a whole. The primary purpose of the network observation is to study large-scale correlations in ultra-high-energy cosmic rays. On the other hand, three nearby stations within 1~km distance at Okayama area have a possibility to detect extremely-high-energy EAS (≍1019 eV) as coincident triggers of the three stations. The present status of the network and some results from computer simulations are reported here.

Directed spatial organization of zinc oxide nanostructures

DOEpatents

Hsu, Julia [Albuquerque, NM; Liu, Jun [Richland, WA

2009-02-17

A method for controllably forming zinc oxide nanostructures on a surface via an organic template, which is formed using a stamp prepared from pre-defined relief structures, inking the stamp with a solution comprising self-assembled monolayer (SAM) molecules, contacting the stamp to the surface, such as Ag sputtered on Si, and immersing the surface with the patterned SAM molecules with a zinc-containing solution with pH control to form zinc oxide nanostructures on the bare Ag surface.

The illegal cigarette market in a socioeconomically deprived inner-city area: the case of the South Bronx.

PubMed

Kurti, Marin K; von Lampe, Klaus; Thompkins, Douglas E

2013-03-01

To determine the scope of the cigarette black market in a socioeconomically deprived inner-city area in the US, taking the South Bronx in New York City as a case study. The South Bronx Litter Pack Survey collected discarded cigarette packs (n=497) along 30 randomised census tracts to quantify the prevalence of counterfeit, legal and out-of-state tax stamps. It was found that 76.2% of cigarette packs collected avoided the combined New York City and State tax. More specifically, 57.9% were untaxed (counterfeit or bearing no tax stamp), for 15.8% taxes were paid outside of New York City (including other states and New York State only). Only 19.4% of tax stamps collected indicated that New York City and New York State taxes were paid. 4.4% of the cigarette packs could not be analysed because the tax stamps were not discernible. The finding that the majority of cigarettes did not have a tax stamp or bore a counterfeit tax stamp suggests that these cigarettes were being bootlegged, most likely from Native American Reservations. The present study highlights the importance of examining the illegal cigarette market in socioeconomically deprived regions of the US, where tax avoidance and black market activities appear to far exceed levels found elsewhere in the country including Chicago and New York City at large.

Seabird tissue archival and monitoring project: Egg collections and analytical results 1999-2002

USGS Publications Warehouse

Vander Pol, Stacy S.; Christopher, Steven J.; Roseneau, David G.; Becker, Paul R.; Day, Russel D.; Kucklick, John R.; Pugh, Rebecca S.; Simac, Kristin S.; Weston-York, Geoff

2003-01-01

In 1998, the U.S. Geological Survey Biological Resources Division (USGS-BRD), the U.S. Fish and Wildlife Service (USFWS) Alaska Maritime National Wildlife Refuge (AMNWR), and the National Institute of Standards and Technology (NIST) began the Seabird Tissue Archival and Monitoring Project (STAMP) to collect and cryogenically bank tissues from seabirds in Alaska for future retrospective analysis of anthropogenic contaminants. The approach of STAMP was similar to that of the Alaska Marine Mammal Tissue Archival Project (AMMTAP). AMMTAP was started in 1987 by NIST and the National Oceanic and Atmospheric Administration (NOAA) as part of the Outer Continental Shelf Environmental Assessment Program sponsored by the Minerals Management Service. Presently sponsored by the USGS-BRD, AMMTAP continues its work as part of a larger national program, the Marine Mammal Health and Stranding Response Program. AMMTAP developed carefully designed sampling and specimen banking protocols. Since 1987, AMMTAP has collected tissues from marine mammals taken in Alaska Native subsistence hunts and has cryogenically banked these tissues at the NIST National Biomonitoring Specimen Bank (NBSB). Through its own analytical work and working in partnership with other researchers both within and outside Alaska, AMMTAP has helped to develop a substantial database on contaminants in Alaska marine mammals. In contrast, data and information is limited on contaminants in Alaska seabirds, which are similar to marine mammals in that they feed near the top of the food chain and have the potential for accumulating anthropogenic contaminants. During its early planning stages, STAMP managers identified the seabird egg as the first tissue of choice for study by the project. There is a relatively long history of using bird eggs for environmental monitoring and for investigating the health status of bird populations. Since 1998, protocols for collecting and processing eggs, and cryogenically banking egg samples have been developed by STAMP (see York et al. 2001). Eggs are being collected on an annual basis for several species at nesting colonies throughout Alaska. Aliquots of these egg samples are being analyzed on a regular basis for persistent organic pollutants and mercury. Results of this work have been published in scientific journals (Christopher et al. 2002) and in conference proceedings (Kucklick et al. 2002; Vander Pol et al. 2002a, 2002b). The intent of this report is to provide an up-to-date description of STAMP. The report contains the most recent egg collection inventory, analytical data, preliminary interpretations based on these data, and a discussion of possible future directions of the project.

Network Design and Performance of the System Integration Test, Linked Simulators Phase.

DTIC Science & Technology

1998-01-01

community has primarily used UNIX systems. UNIX is not a real - time operating system and thus very accurate time stamping, i.e., millisecond accuracy, is... time operating system works against us. The clock time on the UNIX workstations drifts from the UTC standard over time and this drift varies from...loggers at each site use the Network Time Protocol to synchronize to the master clock on a workstation in the TCAC. Again, the fact that UNIX is not a real

Low VHF Channel Measurements and Simulations in Indoor and Outdoor Scenarios

DTIC Science & Technology

2015-05-01

Gregory, Dr Ethan Stamp, Dr John Rodgers, and Stuart H Young of the US Army Research Laboratory for their support with the robotic integration and...our tests.46 The USRP N210 provides an Ethernet interface that allows us to use software control for transmission and reception . The USRP is...dB] B E R Case 3b: LoS in Bldg 205 Measured (LoS) AWGN ( Theory ) Fig. 18 Theoretical and measured BER vs. SNR curves for LOS indoor channel

Determination of Proper Austenitization Temperatures for Hot Stamping of AISI 4140 Steel

NASA Astrophysics Data System (ADS)

Samadian, Pedram; Parsa, Mohammad Habibi; Shakeri, Amid

2014-04-01

High strength steels are desirable materials for use in automobile bodies in order to reduce vehicle weight and increase the safety of car passengers, but steel grades with high strength commonly show poor formability. Recently, steels with controlled microstructures and compositions are used to gain adequate strength after hot stamping while maintaining good formability during processing. In this study, microstructure evolutions and changes in mechanical properties of AISI 4140 steel sheets resulting from the hot stamping process at different austenitization temperatures were investigated. To determine the proper austenitization temperatures, the results were compared with those of the cold-worked and cold-worked plus quench-tempered specimens. Comparisons showed that the austenitization temperatures of 1000 and 1100 °C are proper for hot stamping of 3-mm-thick AISI 4140 steel sheets due to the resultant martensitic microstructure which led to the yield and ultimate tensile strength of 1.3 and 2.1 GPa, respectively. Such conditions resulted in more favorable simultaneous strength and elongation than those of hot-stamped conventional boron steels.

Experimental and Modeling Study of Solvent Diffusion in PDMS for Nanoparticle-Polymer Cosuspension Imprint Lithography.

PubMed

Gervasio, Michelle; Lu, Kathy; Davis, Richey

2015-09-15

This study is the first that focuses on solvent migration in a polydimethylsiloxane (PDMS) stamp during the imprint lithography of ZnO-poly(methyl methacrylate) (PMMA) hybrid suspensions. Using suspensions with varying solids loading levels and ZnO/PMMA ratios, the uptake of the anisole solvent in the stamp is evaluated as a function of time. Laser confocal microscopy is employed as a unique technique to measure the penetration depth of the solvent into the stamp. The suspension solids loading affects the anisole saturation depth in the PDMS stamp. For the suspensions with low solids loading, the experimental data agree with the model for non-Fickian diffusion through a rubbery-elastic polymer. For the suspensions with high solids loading, the data agree more with a sigmoidal diffusion curve, reflecting the rubbery-viscous behavior of a swelling polymer. This difference is due to the degree of swelling in the PDMS. Higher solids loadings induce more swelling because the rate of anisole diffusing into the stamp is increased, likely due to the less dense buildup of the solids as the suspension dries.

Mercury MESSENGER Stamp Unveiling

NASA Image and Video Library

2011-05-03

Patty Carpenter, wife of NASA Mercury Astronaut Scott Carpenter, left, Daughters of NASA astronaut Alan Shepard, Laura Shepard Churchley, and, Alice Wackermann, right, sing the National Anthem during an unveiling ceremony of two USPS stamps that commemorate and celebrate 50 years of US Spaceflight and the MESSENGER program during an event, Wednesday, May 4, 2011 at the NASA Kennedy Space Center in Cape Canaveral, Fla. One stamp commemorates NASA’s Project Mercury, America’s first manned spaceflight program, and NASA astronaut Alan Shepard’s historic flight on May 5, 1961, aboard spacecraft Freedom 7. The other stamp draws attention to NASA’s unmanned MESSENGER mission, a scientific investigation of the planet Mercury. On March 17, 2011, MESSENGER became the first spacecraft to enter into orbit around Mercury. Photo Credit: (NASA/Bill Ingalls)

Prices of unhealthy foods, Food Stamp Program participation, and body weight status among U.S. low-income women†

PubMed Central

Zhang, Qi; Chen, Zhuo; Diawara, Norou; Wang, Youfa

2014-01-01

This paper examines the interactive effect between the price of unhealthy foods and Food Stamp Program participation on body weight status among low-income women in the United States. We merged the panel data of the National Longitudinal Survey of Youth 1979 cohort in 1985–2002 and the Cost of Living Index data compiled by the American Chamber of Commerce Researchers Association by using geographic identifiers. Using the merged data, we used panel econometric models to examine the impact of unhealthy food prices on the food stamp-eligible U.S. population. Our results indicate that higher prices for unhealthy food can partially offset the positive association between Food Stamp Program participation and bodyweight among low-income women. PMID:25177147

Aluminum Nanowire Arrays via Soft Nanoimprint Lithography

NASA Astrophysics Data System (ADS)

Naughton, Michael J.; Nesbitt, Nathan T.; Merlo, Juan M.; Rose, Aaron H.; Calm, Yitzi M.; D'Imperio, Luke A.; Courtney, Dave T.; Shepard, Steve; Kempa, Krzysztof; Burns, Michael J.

We have previously reported a method to fabricate freestanding, vertically-oriented, and lithographically-ordered Al nanowire arrays via directed assembly, and demonstrated their utility as a plasmonic waveguide. However, the process, a variation on the preparation of anodized aluminum oxide (AAO), involved imprinting Al with a hard stamp, which wore down the stamp and had a low yield of Al NWs. Here we show a new nanoimprint lithography (NIL) technique that uses a soft stamp to pattern a mask on the Al; it provides a greater yield of Al NWs and is less destructive to the stamp, providing a path to applications that require NW arrays over macroscopic areas. This material is based upon work supported by the National Science Foundation Graduate Research Fellowship under Grant No. (DGE-1258923).

Ultrasonic angle beam standard reflector. [ultrasonic nondestructive inspection

NASA Technical Reports Server (NTRS)

Berry, R. F., Jr. (Inventor)

1985-01-01

A method that provides an impression profile in a reference standard material utilized in inspecting critically stressed components with pulsed ultrasound is described. A die stamp having an I letter is used to impress the surface of a reference material. The die stamp is placed against the surface and struck with an inertia imparting member to impress the I in the reference standard material. Upset may appear on the surface as a result of the impression and is removed to form a smooth surface. The stamping and upset removal is repeated until the entire surface area of a depth control platform on the die stamp uniformly contacts the material surface. The I impression profile in the reference standard material is utilized for reflecting pulsed ultrasonic beams for inspection purposes.

Large-core single-mode rib SU8 waveguide using solvent-assisted microcontact molding.

PubMed

Huang, Cheng-Sheng; Wang, Wei-Chih

2008-09-01

This paper describes a novel fabrication technique for constructing a polymer-based large-core single-mode rib waveguide. A negative tone SU8 photoresist with a high optical transmission over a large wavelength range and stable mechanical properties was used as a waveguide material. A waveguide was constructed by using a polydimethylsiloxane stamp combined with a solvent-assisted microcontact molding technique. The effects on the final pattern's geometry of four different process conditions were investigated. Optical simulations were performed using beam propagation method software. Single-mode beam propagation was observed at the output of the simulated waveguide as well as the actual waveguide through the microscope image.

Summaries of press automation conference presented

NASA Astrophysics Data System (ADS)

Makhlin, A. Y.; Pokrovskaya, G. M.

1985-01-01

The automation and mechanization of cold and hot stamping were discussed. Problems in the comprehensive mechanization and automatio of stamping in machine building development were examined. Automation becomes effective when it is implemented in progressive manufacturing processes and a comprehensive approach to the solution of all problems, beginning with the delivery of initial materials and ending with the transportation of finished products to the warehouse. Production intensification and improvments of effectiveness of produced output through the comprehensive mechanization and automation of stamping operations are reported.

Design and fabrication of inverted rib waveguide Bragg grating

NASA Astrophysics Data System (ADS)

Huang, Cheng-Sheng; Wang, Wei-Chih

2009-03-01

A polymeric SU8 rib waveguide Bragg grating filterfabricated using reactive ion etching (RIE) and solvent assisted microcontact molding (SAMIM) is presented. SAMIM is one kind of soft lithography. The technique is unique in which that a composite hPDMS/PDMS stamp was used to transfer the grating pattern onto an inverted SU8 rib waveguide system. The composite grating stamp can be used repeatedly several times with degradation. Using this stamp and inverter rib waveguide structure, the Bragg grating filter fabrication can be significantly simplified.

50 CFR 91.1 - Purpose of regulations.

Code of Federal Regulations, 2014 CFR

2014-10-01

... be used for the annual Migratory Bird Hunting and Conservation Stamp (Federal Duck Stamp). (b) All... Reproduction Rights Agreement and Display and Participation Agreement, may be requested from the Federal Duck...

50 CFR 91.1 - Purpose of regulations.

Code of Federal Regulations, 2012 CFR

2012-10-01

... be used for the annual Migratory Bird Hunting and Conservation Stamp (Federal Duck Stamp). (b) All... Reproduction Rights Agreement and Display and Participation Agreement, may be requested from the Federal Duck...

50 CFR 91.1 - Purpose of regulations.

Code of Federal Regulations, 2013 CFR

2013-10-01

... be used for the annual Migratory Bird Hunting and Conservation Stamp (Federal Duck Stamp). (b) All... Reproduction Rights Agreement and Display and Participation Agreement, may be requested from the Federal Duck...

MECHANICAL VIBRATION INHIBITS OSTEOCLAST FORMATION BY REDUCING DC-STAMP RECEPTOR EXPRESSION IN OSTEOCLAST PRECURSOR CELLS

PubMed Central

Kulkarni, R.N.; Voglewede, P.A.; Liu, D.

2014-01-01

It is well known that physical inactivity leads to loss of muscle mass, but it also causes bone loss. Mechanistically, osteoclastogenesis and bone resorption have recently been shown to be regulated by vibration. However, the underlying mechanism behind the inhibition of osteoclast formation is yet unknown. Therefore, we investigated whether mechanical vibration of osteoclast precursor cells affects osteoclast formation by the involvement of fusion-related molecules such as dendritic cell-specific transmembrane protein (DC-STAMP), and P2X7 receptor (P2X7R). RAW264.7 (a murine osteoclastic-like cell line) cells were treated with 20 ng/ml receptor activator of NF-κB ligand (RANKL). For 3 consecutive days, the cells were subjected to 1 hour of mechanical vibration with 20 µm displacement at a frequency of 4 Hz and compared to the control cells that were treated under the same condition but without the vibration. After 5 days of culture, osteoclast formation was determined. Gene expression of DC-STAMP and P2X7R by RAW264.7 cells were determined after 1 hour mechanical vibration, while protein production of the DC-STAMP was determined after 6 hours of post incubation after vibration. As a result, mechanical vibration of RAW264.7 cells inhibited the formation of osteoclasts. Vibration down-regulated DC-STAMP gene expression by 1.6-fold in the presence of RANKL and by 1.4-fold in the absence of RANKL. Additionally, DC-STAMP protein production was also down-regulated by 1.4-fold in the presence of RANKL and by 1.2-fold in the absence of RANKL in RAW264.7 cells in response to mechanical vibration. However, vibration did not affect P2X7R gene expression. Mouse anti-DC-STAMP antibody inhibited osteoclast formation in the absence of vibration. Our results suggest that mechanical vibration of osteoclast precursor cells reduce DC-STAMP expression in osteoclast precursor cells leading to the inhibition of osteoclast formation. PMID:23994170

Digital gamma-gamma coincidence HPGe system for environmental analysis.

PubMed

Marković, Nikola; Roos, Per; Nielsen, Sven Poul

2017-08-01

The performance of a new gamma-gamma coincidence spectrometer system for environmental samples analysis at the Center for Nuclear Technologies of the Technical University of Denmark (DTU) is reported. Nutech Coincidence Low Energy Germanium Sandwich (NUCLeGeS) system consists of two HPGe detectors in a surface laboratory with a digital acquisition system used to collect the data in time-stamped list mode with 10ns time resolution. The spectrometer is used in both anticoincidence and coincidence modes. Copyright © 2017 Elsevier Ltd. All rights reserved.

Smartphones and Time Zones

NASA Astrophysics Data System (ADS)

Baird, William; Secrest, Jeffery; Padgett, Clifford; Johnson, Wayne; Hagrelius, Claire

2016-09-01

Using the Sun to tell time is an ancient idea, but we can take advantage of modern technology to bring it into the 21st century for students in astronomy, physics, or physical science classes. We have employed smartphones, Google Earth, and 3D printing to find the moment of local noon at two widely separated locations. By reviewing GPS time-stamped photos from each place, we are able to illustrate that local noon is longitude-dependent and therefore explain the need for time zones.

78 FR 46927 - Procurement List; Proposed Deletions

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-02

...: 7520-01-453-1968--4 PC STAMPS KIT, ``ACCOUNTANT SET'' NSN: 7520-01-453-1969--4 PC STAMPS KIT, ``MAIL... COORDINATOR, WASHINGTON, DC Service Type/Location: Microfilming Tax Forms Service, Internal Revenue Service...

50 CFR 25.57 - Exceptions and exemptions.

Code of Federal Regulations, 2014 CFR

2014-10-01

...) Persons accompanying the holder of a valid single visit permit, Federal Duck Stamp or Golden Eagle, Age..., children, or parents accompanying the holder of a valid single visit permit, Federal Duck Stamp or Golden...

50 CFR 25.57 - Exceptions and exemptions.

Code of Federal Regulations, 2010 CFR

2010-10-01

...) Persons accompanying the holder of a valid single visit permit, Federal Duck Stamp or Golden Eagle, Age..., children, or parents accompanying the holder of a valid single visit permit, Federal Duck Stamp or Golden...

50 CFR 25.57 - Exceptions and exemptions.

Code of Federal Regulations, 2011 CFR

2011-10-01

...) Persons accompanying the holder of a valid single visit permit, Federal Duck Stamp or Golden Eagle, Age..., children, or parents accompanying the holder of a valid single visit permit, Federal Duck Stamp or Golden...

50 CFR 25.57 - Exceptions and exemptions.

Code of Federal Regulations, 2013 CFR

2013-10-01

...) Persons accompanying the holder of a valid single visit permit, Federal Duck Stamp or Golden Eagle, Age..., children, or parents accompanying the holder of a valid single visit permit, Federal Duck Stamp or Golden...

50 CFR 25.57 - Exceptions and exemptions.

Code of Federal Regulations, 2012 CFR

2012-10-01

...) Persons accompanying the holder of a valid single visit permit, Federal Duck Stamp or Golden Eagle, Age..., children, or parents accompanying the holder of a valid single visit permit, Federal Duck Stamp or Golden...

A framework for development of an intelligent system for design and manufacturing of stamping dies

NASA Astrophysics Data System (ADS)

Hussein, H. M. A.; Kumar, S.

2014-07-01

An integration of computer aided design (CAD), computer aided process planning (CAPP) and computer aided manufacturing (CAM) is required for development of an intelligent system to design and manufacture stamping dies in sheet metal industries. In this paper, a framework for development of an intelligent system for design and manufacturing of stamping dies is proposed. In the proposed framework, the intelligent system is structured in form of various expert system modules for different activities of design and manufacturing of dies. All system modules are integrated with each other. The proposed system takes its input in form of a CAD file of sheet metal part, and then system modules automate all tasks related to design and manufacturing of stamping dies. Modules are coded using Visual Basic (VB) and developed on the platform of AutoCAD software.

Forming of AHSS using Servo-Presses

NASA Astrophysics Data System (ADS)

Groseclose, Adam Richard

Stamping of Advanced High Strength Steel (AHSS) alloys poses several challenges due to the material's higher strength and low formability compared to conventional steels and other problems such as (a) inconsistency of incoming material properties, (b) ductile fracture during forming, (c) higher contact pressure and temperature rise during forming, (d) higher die wear leading to reduced tool life, (e) higher forming load/press capacity, and (f) large springback leading to dimensional inaccuracy in the formed part. [Palaniswamy et. al., 2007]. The use of AHSS has been increasing steadily in automotive stamping. New AHSS alloys (TRIP, TWIP) may replace some of the Hot Stamping applications. Stamping of AHSS alloys, especially higher strength materials, 780 MPa and higher, present new challenges in obtaining good part definition (corner and fillet radii), formability (fracture and resulting scrap) and in reducing springback. Servo-drive presses, having the capability to have infinitely variable and adjustable ram speed and dwell at BDC, offer a potential improvement in quality, part definition, and springback reduction especially when the infinitely adjustable slide motion is used in combination with a CNC hydraulic cushion. Thus, it is desirable to establish a scientific/engineering basis for improving the stamping conditions in forming AHSS using a servo-drive press.

164. Photocopied July 1978. VIEW OF STEAMTURBINE BUILDING AT STAMP ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

164. Photocopied July 1978. VIEW OF STEAM-TURBINE BUILDING AT STAMP MILL. BUILDING CONSTRUCTED IN 1921 TO USE EXHAUST STEAM TO GENERATE ELECTRICITY. C. 1925. - Quincy Mining Company, Hancock, Houghton County, MI

40 CFR 63.11588 - What definitions apply to this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

...-containing products or intermediates other than indelible ink, India ink, writing ink, and stamp pad ink. Indelible ink, India ink, writing ink, and stamp pad ink manufacturing operations are subject to regulation...

40 CFR 63.11588 - What definitions apply to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

...-containing products or intermediates other than indelible ink, India ink, writing ink, and stamp pad ink. Indelible ink, India ink, writing ink, and stamp pad ink manufacturing operations are subject to regulation...

76 FR 70664 - Policy Statement on Grant Stamp Procedure in Routine Director Orders

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-15

... grant stamp unopposed motions for an extension of time or requests for a procedural schedule to which..., Vice Chairman Begeman, and Commissioner Mulvey. Jeffrey Herzig, Clearance Clerk. Appendix [GRAPHIC...

50 CFR 91.24 - Contest procedures.

Code of Federal Regulations, 2011 CFR

2011-10-01

... and the design. The winning artist will receive a pane of Duck Stamps signed by the Secretary of the Interior at the Federal Duck Stamp Contest the following year. The artists placing first, second, and third...

50 CFR 91.24 - Contest procedures.

Code of Federal Regulations, 2013 CFR

2013-10-01

... and the design. The winning artist will receive a pane of Duck Stamps signed by the Secretary of the Interior at the Federal Duck Stamp Contest the following year. The artists placing first, second, and third...

50 CFR 91.24 - Contest procedures.

Code of Federal Regulations, 2012 CFR

2012-10-01

... and the design. The winning artist will receive a pane of Duck Stamps signed by the Secretary of the Interior at the Federal Duck Stamp Contest the following year. The artists placing first, second, and third...

50 CFR 91.24 - Contest procedures.

Code of Federal Regulations, 2010 CFR

2010-10-01

... and the design. The winning artist will receive a pane of Duck Stamps signed by the Secretary of the Interior at the Federal Duck Stamp Contest the following year. The artists placing first, second, and third...

50 CFR 91.24 - Contest procedures.

Code of Federal Regulations, 2014 CFR

2014-10-01

... and the design. The winning artist will receive a pane of Duck Stamps signed by the Secretary of the Interior at the Federal Duck Stamp Contest the following year. The artists placing first, second, and third...

Lightweight Steel Solutions for Automotive Industry

NASA Astrophysics Data System (ADS)

Lee, Hong Woo; Kim, Gyosung; Park, Sung Ho

2010-06-01

Recently, improvement in fuel efficiency and safety has become the biggest issue in worldwide automotive industry. Although the regulation of environment and safety has been tightened up more and more, the majority of vehicle bodies are still manufactured from stamped steel components. This means that the optimized steel solutions enable to demonstrate its ability to reduce body weight with high crashworthiness performance instead of expensive light weight materials such as Al, Mg and composites. To provide the innovative steel solutions for automotive industry, POSCO has developed AHSS and its application technologies, which is directly connected to EVI activities. EVI is a technical cooperation program with customer covering all stages of new car project from design to mass production. Integrated light weight solutions through new forming technologies such as TWB, hydroforming and HPF are continuously developed and provided for EVI activities. This paper will discuss the detailed status of these technologies especially light weight steel solutions based on innovative technologies.

Method of Stamping Surface-Enhance Raman Spectroscopy for Label-Free, Multiplexed, Molecular Sensing and Imaging

NASA Technical Reports Server (NTRS)

Shih, Wei-Chuan (Inventor)

2017-01-01

The present disclosure relates the use of a stamping surface enhanced Raman scattering (S-SERS) technique with nanoporous gold disk (NPGD) plasmonic substrates to produce a label-free, multiplexed molecular sensing and imaging technique. A NPGD SERS substrate is stamped onto a surface containing one or more target molecules, followed by SERS measurement of the target molecules located between the surface and SERS substrate. The target molecules may be deposited on the surface, which may be a carrier substrate such as polydimethylsiloxane (PDMS).

A concurrent resolution expressing the sense of Congress that the United States Postal Service should issue a commemorative postage stamp honoring civil rights workers Andrew Goodman, James Chaney, and Michael Schwerner, and the "Freedom Summer" of 1964, and that the Citizens' Stamp Advisory Committee should recommend to the Postmaster General that such a stamp be issued.

THOMAS, 111th Congress

Sen. Schumer, Charles E. [D-NY

2010-07-12

Senate - 07/15/2010 Committee on Homeland Security and Governmental Affairs referred to Subcommittee on Federal Financial Management, Government Information, Federal Services, and International Security. (All Actions) Tracker: This bill has the status IntroducedHere are the steps for Status of Legislation:

75 FR 29803 - Agency Information Collection Activity Seeking OMB Approval

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-27

.... 75, no. 44, page 10548. The date of manufacture and compliance status stamped on a nameplate of each...: An estimated 100 hours annually. Abstract: The date of manufacture and compliance status stamped on a...

VIEW OF ONESTAMP MILL WITH RANCH HOUSE AT REAR (See ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

VIEW OF ONE-STAMP MILL WITH RANCH HOUSE AT REAR (See HABS No. CA-2347, DESERT QUEEN RANCH, for further documentation) - Desert Queen Ranch, One Stamp Gold Mill, Twentynine Palms, San Bernardino County, CA

49 CFR 179.400-24 - Stamping.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Specification for Cryogenic Liquid Tank Car Tanks and Seamless Steel Tanks (Classes DOT-113 and 107A) § 179.400... of required stamping Specification DOT-113A60W. Design service temperature Minus 423° F. Inner tank...

47. DETAIL OF UPPER STAMP BATTERIES CAMS, TAPPETS AND STEMS, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

47. DETAIL OF UPPER STAMP BATTERIES CAMS, TAPPETS AND STEMS, LOOKING NORTH NORTHWEST. SEE CA-290-22 FOR IDENTICAL B&W NEGATIVE. - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

22. DETAIL OF UPPER STAMP BATTERIES CAMS, TAPPETS AND STEMS, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

22. DETAIL OF UPPER STAMP BATTERIES CAMS, TAPPETS AND STEMS, LOOKING NORTH NORTHWEST. SEE CA-290-47 (CT) FOR IDENTICAL COLOR TRANSPARENCY. - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

49 CFR 238.119 - Rim-stamped straight-plate wheels.

Code of Federal Regulations, 2010 CFR

2010-10-01

... input to the wheel during braking. (b) A rim-stamped straight-plate wheel shall not be used as a... that is periodically tread-braked for a short duration by automatic circuitry for the sole purpose of...

Effects of atamp-charging coke making on strength and high temperature thermal properties of coke.

PubMed

Zhang, Yaru; Bai, Jinfeng; Xu, Jun; Zhong, Xiangyun; Zhao, Zhenning; Liu, Hongchun

2013-12-01

The stamp-charging coke making process has some advantages of improving the operation environment, decreasing fugitive emission, higher gas collection efficiency as well as less environmental pollution. This article describes the different structure strength and high temperature thermal properties of 4 different types of coke manufactured using a conventional coking process and the stamp-charging coke making process. The 4 kinds of cokes were prepared from the mixture of five feed coals blended by the petrography blending method. The results showed that the structure strength indices of coke prepared using the stamp-charging coke method increase sharply. In contrast with conventional coking process, the stamp-charging process improved the coke strength after reaction but had little impact on the coke reactivity index. Copyright © 2013 The Research Centre for Eco-Environmental Sciences, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.

Rasch analysis of Stamps's Index of Work Satisfaction in nursing population.

PubMed

Ahmad, Nora; Oranye, Nelson Ositadimma; Danilov, Alyona

2017-01-01

One of the most commonly used tools for measuring job satisfaction in nursing is the Stamps Index of Work Satisfaction. Several studies have reported on the reliability of the Stamps' tool based on traditional statistical model. The aim of this study was to apply the Rasch model to examine the adequacy of Stamps's Index of Work Satisfaction for measuring nurses' job satisfaction cross-culturally and to determine the validity and reliability of the instrument using the Rasch criteria. A secondary data analysis was conducted on a sample of 556 registered nurses from two countries. The RUMM 2030 software was used to analyse the psychometric properties of the Index of Work Satisfaction. The persons mean location of -0.018 approximated the items mean of 0.00, suggesting a good alignment of the measure and the traits being measured. However, at the items level, some items were misfiting to the Rasch model.

Tailor-welded blanks and their production

NASA Astrophysics Data System (ADS)

Yan, Qi

2005-01-01

Tailor welded blanks had been widely used in the automobile industry. A tailor welded blank consists of several flat sheets that were laser welded together before stamping. A combination of different materials, thickness, and coatings could be welded together to form a blank for stamping car body panels. As for the material for automobile industry, this technology was one of the development trend for automobile industry because of its weight reduction, safety improvement and economical use of materials. In this paper, the characters and production of tailor welded blanks in the market were discussed in detail. There had two major methods to produce tailor welded blanks. Laser welding would replace mesh seam welding for the production of tailor welded blanks in the future. The requirements on the edge preparation of unwelded blanks for tailor welded blanks were higher than the other steel processing technology. In order to produce the laser welded blank, there had the other process before the laser welding in the factory. In the world, there had three kinds of patterns for the large volume production of tailor welded blanks. In China, steel factory played the important role in the promotion of the application of tailor welded blanks. The competition for the supply of tailor welded blanks to the automobile industry would become fierce in the near future. As a result, the demand for the quality control on the production of tailor welded blanks would be the first priority concern for the factory.

Should Canadian health promoters support a food stamp-style program to address food insecurity?

PubMed

Power, Elaine M; Little, Margaret H; Collins, Patricia A

2015-03-01

Food insecurity is an urgent public health problem in Canada, affecting 4 million Canadians in 2012, including 1.15 million children, and associated with significant health concerns. With little political will to address this significant policy issue, it has been suggested that perhaps it is time for Canada to try a food stamp-style program. Such a program could reduce rates of food insecurity and improve the nutritional health of low-income Canadians. In this article, we explore the history of the US food stamp program; the key impetus of which was to support farmers and agricultural interests, not to look after the needs of people living in poverty. Though the US program has moved away from its roots, its history has had a lasting legacy, cementing an understanding of the problem as one of lack of food, not lack of income. While the contemporary food stamp program, now called Supplemental Nutrition Assistance Program (SNAP), reduces rates of poverty and food insecurity, food insecurity rates in the USA are significantly higher than those in Canada, suggesting a food stamp-style program per se will not eliminate the problem of food insecurity. Moreover, a food stamp-style program is inherently paternalistic and would create harm by reducing the autonomy of participants and generating stigma, which in itself has adverse health effects. Consequently, it is ethically problematic for health promoters to advocate for such a program, even if it could improve diet quality. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Can we use digital life-log images to investigate active and sedentary travel behaviour? Results from a pilot study

PubMed Central

2011-01-01

Background Active travel such as walking and cycling has potential to increase physical activity levels in sedentary individuals. Motorised car travel is a sedentary behaviour that contributes to carbon emissions. There have been recent calls for technology that will improve our ability to measure these travel behaviours, and in particular evaluate modes and volumes of active versus sedentary travel. The purpose of this pilot study is to investigate the potential efficacy of a new electronic measurement device, a wearable digital camera called SenseCam, in travel research. Methods Participants (n = 20) were required to wear the SenseCam device for one full day of travel. The device automatically records approximately 3,600 time-stamped, first-person point-of-view images per day, without any action required by the wearer. Participants also completed a self-report travel diary over the same period for comparison, and were interviewed afterwards to assess user burden and experience. Results There were a total of 105 confirmed journeys in this pilot. The new SenseCam device recorded more journeys than the travel diary (99 vs. 94). Although the two measures demonstrated an acceptable correlation for journey duration (r = 0.92, p < 0.001) self-reported journey duration was over-reported (mean difference 154 s per journey; 95% CI = 89 to 218 s; 95% limits of agreement = 154 ± 598 s (-444 to 752 s)). The device also provided visual data that was used for directed interviews about sources of error. Conclusions Direct observation of travel behaviour from time-stamped images shows considerable potential in the field of travel research. Journey duration derived from direct observation of travel behaviour from time-stamped images appears to suggest over-reporting of self-reported journey duration. PMID:21599935

Can we use digital life-log images to investigate active and sedentary travel behaviour? Results from a pilot study.

PubMed

Kelly, Paul; Doherty, Aiden; Berry, Emma; Hodges, Steve; Batterham, Alan M; Foster, Charlie

2011-05-20

Active travel such as walking and cycling has potential to increase physical activity levels in sedentary individuals. Motorised car travel is a sedentary behaviour that contributes to carbon emissions. There have been recent calls for technology that will improve our ability to measure these travel behaviours, and in particular evaluate modes and volumes of active versus sedentary travel. The purpose of this pilot study is to investigate the potential efficacy of a new electronic measurement device, a wearable digital camera called SenseCam, in travel research. Participants (n = 20) were required to wear the SenseCam device for one full day of travel. The device automatically records approximately 3,600 time-stamped, first-person point-of-view images per day, without any action required by the wearer. Participants also completed a self-report travel diary over the same period for comparison, and were interviewed afterwards to assess user burden and experience. There were a total of 105 confirmed journeys in this pilot. The new SenseCam device recorded more journeys than the travel diary (99 vs. 94). Although the two measures demonstrated an acceptable correlation for journey duration (r = 0.92, p < 0.001) self-reported journey duration was over-reported (mean difference 154 s per journey; 95% CI = 89 to 218 s; 95% limits of agreement = 154 ± 598 s (-444 to 752 s)). The device also provided visual data that was used for directed interviews about sources of error. Direct observation of travel behaviour from time-stamped images shows considerable potential in the field of travel research. Journey duration derived from direct observation of travel behaviour from time-stamped images appears to suggest over-reporting of self-reported journey duration.

75 FR 52981 - Chrysler, LLC; Twinsburg Stamping Plant, Including On-Site Leased Workers from Caravan Knight...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-30

... production of metal automotive stampings, a substantial proportion of which are shipped to an affiliated plant where they are used in the assembly of automotive vehicles. New information shows that workers...

Chemistry on Stamps.

ERIC Educational Resources Information Center

Schreck, James O.

1986-01-01

Suggests how postage stamps can be incorporated into chemistry teaching. Categories considered include emergence of chemistry as a science, metric system, atoms (and molecules and ions), stoichiometry, energy relationships in chemical systems, chemical bonding, nuclear chemistry, biochemistry, geochemistry, matter (gases, liquids, and solids),…

26 CFR 301.7209-1 - Unauthorized use or sale of stamps.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., transfers, takes or gives in exchange, or pledges or gives in pledge, except as authorized in the Code or in regulations made pursuant thereto, any stamp, coupon, ticket, book, or other device prescribed by the...

31 CFR 500.410 - Currency, coins, and postage and other stamps.

Code of Federal Regulations, 2010 CFR

2010-07-01

... postage and other stamps issued by North Korea, North Viet-Nam, Cambodia, or South Viet-Nam are merchandise of North Korean, North Vietnamese, Cambodian, or South Vietnamese origin subject to § 500.204(a)(1...

Software Modules for the Proximity-1 Space Link Interleaved Time Synchronization (PITS) Protocol

NASA Technical Reports Server (NTRS)

Woo, Simon S.; Veregge, John R.; Gao, Jay L.; Clare, Loren P.; Mills, David

2012-01-01

The Proximity-1 Space Link Interleaved Time Synchronization (PITS) protocol provides time distribution and synchronization services for space systems. A software prototype implementation of the PITS algorithm has been developed that also provides the test harness to evaluate the key functionalities of PITS with simulated data source and sink. PITS integrates time synchronization functionality into the link layer of the CCSDS Proximity-1 Space Link Protocol. The software prototype implements the network packet format, data structures, and transmit- and receive-timestamp function for a time server and a client. The software also simulates the transmit and receive-time stamp exchanges via UDP (User Datagram Protocol) socket between a time server and a time client, and produces relative time offsets and delay estimates.

11. Detail of log stamp on ends of plank, near ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. Detail of log stamp on ends of plank, near the Minnesota end of the bridge - Enloe Bridge No. 90021, Spanning Red River of North between Minnesota & North Dakota on County State Aid Highway 28, Wolverton, Wilkin County, MN

7 CFR 273.20 - SSI cash-out.

Code of Federal Regulations, 2011 CFR

2011-01-01

... in California have been specifically increased to include the value of the food stamp allotment. (b... Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM CERTIFICATION OF ELIGIBLE HOUSEHOLDS Program Alternatives...

7 CFR 275.8 - Review coverage.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM PERFORMANCE REPORTING SYSTEM Management Evaluation (ME... upon the provisions of the regulations governing the Food Stamp Program and the FNS-approved Plan of...

49 CFR 179.200-24 - Stamping.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION HAZARDOUS MATERIALS REGULATIONS SPECIFICATIONS FOR TANK CARS Specifications for Non-Pressure Tank Car Tanks (Classes DOT-111AW and 115AW) § 179.200-24 Stamping. (a) To...

49 CFR 179.100-20 - Stamping.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION HAZARDOUS MATERIALS REGULATIONS SPECIFICATIONS FOR TANK CARS Specifications for Pressure Tank Car Tanks (Classes DOT-105, 109, 112, 114 and 120) § 179.100-20 Stamping. (a) To...

Postage Stamps as Pedagogical Instruments in the Italian Curriculum.

ERIC Educational Resources Information Center

Nuessel, Frank; Cicogna, Caterina

1992-01-01

Examination of several interrelated topics on postage stamps, including their multiple functions and significance as semiotic artifacts, precedes suggestions for incorporating them into the Italian language curriculum in such activities as reading, writing, speaking, listening, and cultural understanding. (CB)

Stamps Tell the Story of Nuclear Energy.

ERIC Educational Resources Information Center

Angelo, Joseph A., Jr.

This document provides a summary history of the individual scientists principally responsible for the development of nuclear physics and a survey of modern utilization of atomic energy. Identified throughout the booklet are postage stamps illustrating each individual and topic discussed. (SL)

48. DETAIL OF STAMP BATTERIES CAMS, TAPPETS AND STEMS WITH ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

48. DETAIL OF STAMP BATTERIES CAMS, TAPPETS AND STEMS WITH SIX FOOT SCALE, LOOKING NORTH NORTHWEST. SEE CA-290-24 FOR IDENTICAL B&W NEGATIVE. - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

24. DETAIL OF STAMP BATTERIES CAMS, TAPPETS AND STEMS WITH ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

24. DETAIL OF STAMP BATTERIES CAMS, TAPPETS AND STEMS WITH SIX FOOT SCALE, LOOKING NORTH NORTHWEST. SEE CA-290-48 (CT) FOR IDENTICAL COLOR TRANSPARENCY. - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

75 FR 5236 - New Postal Product

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-02

... Description] Premium Stamped Stationery [Reserved for Product Description] Premium Stamped Cards [Reserved for... determine whether such an agreement (1) Improves the net financial position of the Postal Service or... Descriptions First-Class Mail [Reserved for Class Description] Single-Piece Letters/Postcards [Reserved for...

The restoration of obliterated stamped serial numbers by ultrasonically induced cavitation in water

NASA Technical Reports Server (NTRS)

Young, S. G.

1973-01-01

Seventeen out of 21 obliterated stamped serial numbers on test specimens of copper, brass, steel, and aluminum were successfully restored. Cavitation induced in water by a piezoelectric transducer was the mechanism used. Primarily, smeared metal was removed from the number grooves by the force of the cavitation, however, numbers were also restored at depths at or below the level of the stamped grooves. The feasibility of this technique as a low cost tool for crime laboratories has been clearly demonstrated. The technique is applicable to a variety of materials, and no previous surface or chemical treatments are necessary.

KSC-2011-3302

NASA Image and Video Library

2011-05-04

CAPE CANAVERAL, Fla. -- In the Rocket Garden at NASA's Kennedy Space Center Visitor Complex in Florida, a United States Postal Service poster reveals the two new stamps that commemorate the 50th anniversary of human spaceflight. One stamp commemorates NASA's Project Mercury and Alan Shepard's historic launch on May 5, 1961, aboard the spacecraft Freedom 7. The second stamp honors NASA's MESSENGER, which reached Mercury in March to become the first spacecraft to orbit the planet. The two missions frame a remarkable 50-year period in which America advanced space exploration through more than 1,500 crewed and uncrewed flights. Photo credit: NASA/Kim Shiflett

KSC00pp0021

NASA Image and Video Library

2000-01-12

One of a new series of U.S. Postage stamps, The 1980s, is unveiled at the KSC Visitors Complex. The stamp, shown here, is the Space Shuttle Columbia, first launched in April 1981. This collection of stamps is the ninth in the Post Office's "Celebrate the Century" commemorative series honoring the last 100 years of American history. Taking part in the "First Day of Issue Ceremony" were astronaut Richard Linnehan, U.S. Representative, 15th Congressional District, Dave Weldon, U.S. Postal Service District Manager Viki Brennan, Center Director Roy Bridges and President of the Visitor Complex Rick Abramson

KSC-00pp0022

NASA Image and Video Library

2000-01-12

A new series of U.S. Postage stamps, The 1980s, is unveiled at the KSC Visitors Complex. Taking part in the "First Day of Issue Ceremony" were astronaut Richard Linnehan, U.S. Representative, 15th Congressional District, Dave Weldon, U.S. Postal Service District Manager Viki Brennan, Center Director Roy Bridges and President of the Visitor Complex Rick Abramson. Among the stamps issued is one of Space Shuttle Columbia (upper left corner), first launched in April 1981. This collection of stamps is the ninth in the Post Office's "Celebrate the Century" commemorative series honoring the last 100 years of American history

KSC00pp0010

NASA Image and Video Library

2000-01-12

A new series of U.S. Postage stamps, The 1980s, is unveiled at the KSC Visitors Complex. Shown taking part in the "First Day of Issue Ceremony" are (left to right) astronaut Richard Linnehan, U.S. Representative, 15th Congressional District, Dave Weldon, U.S. Postal Service District Manager Viki Brennan, Center Director Roy Bridges and President of the Visitor Complex Rick Abramson. Among the stamps issued is one of Space Shuttle Columbia, first launched in April 1981. This collection of stamps is the ninth in the Post Office's "Celebrate the Century" commemorative series honoring the last 100 years of American history

KSC-00pp0010

NASA Image and Video Library

2000-01-12

A new series of U.S. Postage stamps, The 1980s, is unveiled at the KSC Visitors Complex. Shown taking part in the "First Day of Issue Ceremony" are (left to right) astronaut Richard Linnehan, U.S. Representative, 15th Congressional District, Dave Weldon, U.S. Postal Service District Manager Viki Brennan, Center Director Roy Bridges and President of the Visitor Complex Rick Abramson. Among the stamps issued is one of Space Shuttle Columbia, first launched in April 1981. This collection of stamps is the ninth in the Post Office's "Celebrate the Century" commemorative series honoring the last 100 years of American history

KSC00pp0022

NASA Image and Video Library

2000-01-12

A new series of U.S. Postage stamps, The 1980s, is unveiled at the KSC Visitors Complex. Taking part in the "First Day of Issue Ceremony" were astronaut Richard Linnehan, U.S. Representative, 15th Congressional District, Dave Weldon, U.S. Postal Service District Manager Viki Brennan, Center Director Roy Bridges and President of the Visitor Complex Rick Abramson. Among the stamps issued is one of Space Shuttle Columbia (upper left corner), first launched in April 1981. This collection of stamps is the ninth in the Post Office's "Celebrate the Century" commemorative series honoring the last 100 years of American history

KSC-00pp0021

NASA Image and Video Library

2000-01-12

One of a new series of U.S. Postage stamps, The 1980s, is unveiled at the KSC Visitors Complex. The stamp, shown here, is the Space Shuttle Columbia, first launched in April 1981. This collection of stamps is the ninth in the Post Office's "Celebrate the Century" commemorative series honoring the last 100 years of American history. Taking part in the "First Day of Issue Ceremony" were astronaut Richard Linnehan, U.S. Representative, 15th Congressional District, Dave Weldon, U.S. Postal Service District Manager Viki Brennan, Center Director Roy Bridges and President of the Visitor Complex Rick Abramson

KSC00pp0011

NASA Image and Video Library

2000-01-12

One of a new series of U.S. Postage stamps, The 1980s, is unveiled at the KSC Visitors Complex. The stamp, shown here, is the Space Shuttle Columbia, first launched in April 1981. This collection of stamps is the ninth in the Post Office's "Celebrate the Century" commemorative series honoring the last 100 years of American history. Taking part in the "First Day of Issue Ceremony" are (left to right) astronaut Richard Linnehan, U.S. Representative, 15th Congressional District, Dave Weldon, U.S. Postal Service District Manager Viki Brennan, Center Director Roy Bridges and President of the Visitor Complex Rick Abramson

KSC-00pp0011

NASA Image and Video Library

2000-01-12

One of a new series of U.S. Postage stamps, The 1980s, is unveiled at the KSC Visitors Complex. The stamp, shown here, is the Space Shuttle Columbia, first launched in April 1981. This collection of stamps is the ninth in the Post Office's "Celebrate the Century" commemorative series honoring the last 100 years of American history. Taking part in the "First Day of Issue Ceremony" are (left to right) astronaut Richard Linnehan, U.S. Representative, 15th Congressional District, Dave Weldon, U.S. Postal Service District Manager Viki Brennan, Center Director Roy Bridges and President of the Visitor Complex Rick Abramson

ELID grinding characteristics of large stamping die for Wolter mirror.

PubMed

Yin, Shaohui; Ohmori, Hitoshi; Liu, Qing; Morita, Shinnya; Chen, Fengjun; Asami, Muneaki; Fan, Yufeng

2009-01-01

An ultra-precision ELID grinding of large stamping dies of Wolter mirror for X-ray telescope was presented in this paper. The large stamping dies (S55C) with confocal paraboloid and hyperboloid was ground by ELID arc-enveloped grinding. In this ELID grinding system, cast iron fiber bonded (CIFB) diamond wheels were controlled by 3-dimentional ways to scan the work-piece and generate required surfaces. Its grinding characteristics such as attainable form accuracy, surface roughness were investigated. Furthermore, some measures to improve form accuracy were discussed and verified such as truing, compensating, and on-machine measuring.

A rapid co-culture stamping device for studying intercellular communication.

PubMed

Hassanzadeh-Barforoushi, Amin; Shemesh, Jonathan; Farbehi, Nona; Asadnia, Mohsen; Yeoh, Guan Heng; Harvey, Richard P; Nordon, Robert E; Warkiani, Majid Ebrahimi

2016-10-18

Regulation of tissue development and repair depends on communication between neighbouring cells. Recent advances in cell micro-contact printing and microfluidics have facilitated the in-vitro study of homotypic and heterotypic cell-cell interaction. Nonetheless, these techniques are still complicated to perform and as a result, are seldom used by biologists. We report here development of a temporarily sealed microfluidic stamping device which utilizes a novel valve design for patterning two adherent cell lines with well-defined interlacing configurations to study cell-cell interactions. We demonstrate post-stamping cell viability of >95%, the stamping of multiple adherent cell types, and the ability to control the seeded cell density. We also show viability, proliferation and migration of cultured cells, enabling analysis of co-culture boundary conditions on cell fate. We also developed an in-vitro model of endothelial and cardiac stem cell interactions, which are thought to regulate coronary repair after myocardial injury. The stamp is fabricated using microfabrication techniques, is operated with a lab pipettor and uses very low reagent volumes of 20 μl with cell injection efficiency of >70%. This easy-to-use device provides a general strategy for micro-patterning of multiple cell types and will be important for studying cell-cell interactions in a multitude of applications.

Design of Channel Type Indirect Blank Holder for Prevention of Wrinkling and Fracture in Hot Stamping Process

NASA Astrophysics Data System (ADS)

Choi, Hong-seok; Ha, Se-yoon; Cha, Seung-hoon; kang, Chung-gil; Kim, Byung-min

2011-08-01

The hot stamping process has been used in the automotive industry to reduce the weight of the body-in-white and to increase passenger safety via improved crashworthiness. In this study, a new form die with a simple structure that can prevent defects such as wrinkle and fracture is proposed for the manufacture of hot stamped components. The wrinkling at the flange cannot be eliminated when using a conventional form die. It is known that the initiation of wrinkling is influenced by many factors such as the mechanical properties of the sheet material, geometry of the sheet and tool, and other process parameters, including the blank holding force (BHF) and the contact conditions. In this research, channel type indirect blank holder (CIBH) is introduced to replace general blank holder for manufacturing the hot stamped center pillar. First, we investigate the tension force acting on the blank according to the channel shapes. We determine the appropriate range by comparing the tension force with the upper and lower BHFs in a conventional stamping process. We then use FE-analysis to study the influence of the slope angle and corner radius of the channel on the formability. Finally, the center pillar is manufactured using the form die with the selected channel.

A rapid co-culture stamping device for studying intercellular communication

NASA Astrophysics Data System (ADS)

Hassanzadeh-Barforoushi, Amin; Shemesh, Jonathan; Farbehi, Nona; Asadnia, Mohsen; Yeoh, Guan Heng; Harvey, Richard P.; Nordon, Robert E.; Warkiani, Majid Ebrahimi

2016-10-01

Regulation of tissue development and repair depends on communication between neighbouring cells. Recent advances in cell micro-contact printing and microfluidics have facilitated the in-vitro study of homotypic and heterotypic cell-cell interaction. Nonetheless, these techniques are still complicated to perform and as a result, are seldom used by biologists. We report here development of a temporarily sealed microfluidic stamping device which utilizes a novel valve design for patterning two adherent cell lines with well-defined interlacing configurations to study cell-cell interactions. We demonstrate post-stamping cell viability of >95%, the stamping of multiple adherent cell types, and the ability to control the seeded cell density. We also show viability, proliferation and migration of cultured cells, enabling analysis of co-culture boundary conditions on cell fate. We also developed an in-vitro model of endothelial and cardiac stem cell interactions, which are thought to regulate coronary repair after myocardial injury. The stamp is fabricated using microfabrication techniques, is operated with a lab pipettor and uses very low reagent volumes of 20 μl with cell injection efficiency of >70%. This easy-to-use device provides a general strategy for micro-patterning of multiple cell types and will be important for studying cell-cell interactions in a multitude of applications.

77 FR 16165 - United States Savings Bonds and Notes; Payments

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-20

... security by imprinting the word ``PAID'' on its face and entering the amount and date of the actual payment... imprint of a payment stamp. The stamp may not exceed 1\\1/8\\ inches in any dimension and must include the...

7 CFR 275.5 - Scope and purpose.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM PERFORMANCE REPORTING SYSTEM Management Evaluation (ME... operate the Food Stamp Program in accordance with the Act, regulations, and FNS-approved State Plan of...

27 CFR 479.162 - Stamps authorized.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2011-04-01 2010-04-01 true Stamps authorized. 479.162 Section 479.162 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES, AND CERTAIN...

27 CFR 479.162 - Stamps authorized.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2012-04-01 2010-04-01 true Stamps authorized. 479.162 Section 479.162 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES, AND CERTAIN...

27 CFR 479.162 - Stamps authorized.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2014-04-01 2014-04-01 false Stamps authorized. 479.162 Section 479.162 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES, AND CERTAIN...

27 CFR 479.162 - Stamps authorized.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2013-04-01 2013-04-01 false Stamps authorized. 479.162 Section 479.162 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES, AND CERTAIN...

27 CFR 479.162 - Stamps authorized.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Stamps authorized. 479.162 Section 479.162 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES, AND CERTAIN...

Teaching Hispanic Culture with Postage Stamps.

ERIC Educational Resources Information Center

Nuessel, Frank

1984-01-01

Methods for using postage stamps to their greatest potential in any level Spanish class are outlined, with illustrations and examples provided. Among the subjects that can be addressed through this medium are economics, politics, anthropology, archaeology, history, language and literature, geography, and music. (MSE)

49 CFR 179.220-25 - Stamping.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR TANK CARS Specifications for Non-Pressure Tank Car Tanks (Classes DOT-111AW and 115AW) § 179.220-25 Stamping. To certify that the tank...

49 CFR 179.100-20 - Stamping.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR TANK CARS Specifications for Pressure Tank Car Tanks (Classes DOT-105, 109, 112, 114 and 120) § 179.100-20 Stamping. (a) To certify that the...

49 CFR 179.100-20 - Stamping.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR TANK CARS Specifications for Pressure Tank Car Tanks (Classes DOT-105, 109, 112, 114 and 120) § 179.100-20 Stamping. (a) To certify that the...

49 CFR 179.100-20 - Stamping.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR TANK CARS Specifications for Pressure Tank Car Tanks (Classes DOT-105, 109, 112, 114 and 120) § 179.100-20 Stamping. (a) To certify that the...

7 CFR 277.1 - General purpose and scope.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Food Stamp Program on Indian Reservations. (b) Scope and applicability. Upon compliance with the... the Food Stamp Program and for administration of the Food Distribution Program on Indian Reservations... Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF...

7 CFR 281.8 - Transfer of program administration.

Code of Federal Regulations, 2011 CFR

2011-01-01

....8 Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM ADMINISTRATION OF THE FOOD STAMP PROGRAM ON INDIAN RESERVATIONS § 281.8 Transfer of program administration. The transfer of program...

7 CFR 275.10 - Scope and purpose.

Code of Federal Regulations, 2010 CFR

2010-01-01

... to enhanced funding. (b) The objectives of quality control reviews are to provide: (1) A systematic... FOOD STAMP AND FOOD DISTRIBUTION PROGRAM PERFORMANCE REPORTING SYSTEM Quality Control (QC) Reviews... responsible for conducting quality control reviews. For food stamp quality control reviews, a sample of...

7 CFR 281.2 - Administration.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 4 2010-01-01 2010-01-01 false Administration. 281.2 Section 281.2 Agriculture... FOOD STAMP AND FOOD DISTRIBUTION PROGRAM ADMINISTRATION OF THE FOOD STAMP PROGRAM ON INDIAN RESERVATIONS § 281.2 Administration. (a) Qualification. (1) The appropriate ITO of an established Indian...

39 CFR 3.4 - Matters reserved for decision by the Governors.

Code of Federal Regulations, 2011 CFR

2011-07-01

... General under section 5 of the Inspector General Act. (m) Establishment of the price of the breast cancer research special postage stamp under 39 U.S.C. 414 and any semipostal stamp under 39 U.S.C. 416. (n...

39 CFR 3.4 - Matters reserved for decision by the Governors.

Code of Federal Regulations, 2013 CFR

2013-07-01

... General under section 5 of the Inspector General Act. (m) Establishment of the price of the breast cancer research special postage stamp under 39 U.S.C. 414 and any semipostal stamp under 39 U.S.C. 416. (n...

39 CFR 3.4 - Matters reserved for decision by the Governors.

Code of Federal Regulations, 2012 CFR

2012-07-01

... General under section 5 of the Inspector General Act. (m) Establishment of the price of the breast cancer research special postage stamp under 39 U.S.C. 414 and any semipostal stamp under 39 U.S.C. 416. (n...

39 CFR 3.4 - Matters reserved for decision by the Governors.

Code of Federal Regulations, 2014 CFR

2014-07-01

... General under section 5 of the Inspector General Act. (m) Establishment of the price of the breast cancer research special postage stamp under 39 U.S.C. 414 and any semipostal stamp under 39 U.S.C. 416. (n...

39 CFR 3.4 - Matters reserved for decision by the Governors.

Code of Federal Regulations, 2010 CFR

2010-07-01

... General under section 5 of the Inspector General Act. (m) Establishment of the price of the breast cancer research special postage stamp under 39 U.S.C. 414 and any semipostal stamp under 39 U.S.C. 416. (n...

7 CFR 275.10 - Scope and purpose.

Code of Federal Regulations, 2011 CFR

2011-01-01

... FOOD STAMP AND FOOD DISTRIBUTION PROGRAM PERFORMANCE REPORTING SYSTEM Quality Control (QC) Reviews... responsible for conducting quality control reviews. For food stamp quality control reviews, a sample of... terminated (called negative cases). Reviews shall be conducted on active cases to determine if households are...

7 CFR 281.2 - Administration.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 4 2013-01-01 2013-01-01 false Administration. 281.2 Section 281.2 Agriculture... FOOD STAMP AND FOOD DISTRIBUTION PROGRAM ADMINISTRATION OF THE FOOD STAMP PROGRAM ON INDIAN RESERVATIONS § 281.2 Administration. (a) Qualification. (1) The appropriate ITO of an established Indian...

7 CFR 281.2 - Administration.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 4 2012-01-01 2012-01-01 false Administration. 281.2 Section 281.2 Agriculture... FOOD STAMP AND FOOD DISTRIBUTION PROGRAM ADMINISTRATION OF THE FOOD STAMP PROGRAM ON INDIAN RESERVATIONS § 281.2 Administration. (a) Qualification. (1) The appropriate ITO of an established Indian...

40 CFR 165.45 - Refillable container standards.

Code of Federal Regulations, 2014 CFR

2014-07-01

... pesticide container must be capable of withstanding all operating stresses, taking into account static heat, pressure buildup from pumps and compressors, and any other foreseeable mechanical stresses to which the..., but is not limited to, etching, embossing, ink jetting, stamping, heat stamping, mechanically...

31 CFR 100.18 - Counterfeit notes to be marked; “redemption” of notes wrongfully so marked.

Code of Federal Regulations, 2010 CFR

2010-07-01

... moneys, and all officers of national banks, shall stamp or write in plain letters the word “counterfeit... money, which shall be presented at their places of business; and if such officers shall wrongfully stamp...

Tiny Devices Project Sharp, Colorful Images

NASA Technical Reports Server (NTRS)

2009-01-01

Displaytech Inc., based in Longmont, Colorado and recently acquired by Micron Technology Inc. of Boise, Idaho, first received a Small Business Innovation Research contract in 1993 from Johnson Space Center to develop tiny, electronic, color displays, called microdisplays. Displaytech has since sold over 20 million microdisplays and was ranked one of the fastest growing technology companies by Deloitte and Touche in 2005. Customers currently incorporate the microdisplays in tiny pico-projectors, which weigh only a few ounces and attach to media players, cell phones, and other devices. The projectors can convert a digital image from the typical postage stamp size into a bright, clear, four-foot projection. The company believes sales of this type of pico-projector may exceed $1.1 billion within 5 years.

Clinical significance of nutritional risk screening tool for hospitalised children with acute burn injuries: a cross-sectional study.

PubMed

Bang, Y K; Park, M K; Ju, Y S; Cho, K Y

2018-06-01

We assessed the nutritional risks among children hospitalised with acute burn injuries and their associated clinical outcomes using three nutritional risk screening (NRS) tools: Screening Tool for Risk of Impaired Nutritional Status and Growth (STRONG KIDS ), Pediatric Yorkhill Malnutrition Score (PYMS) and Screening Tool for the Assessment for Malnutrition in Pediatrics (STAMP). This prospective cross-sectional study was conducted from October 2015 to November 2016, in a regional burn centre. Patients were screened by two independent observers, using the three NRS tools. A total of 100 children aged 3 months to 16.5 years were included. STRONG KIDS identified 16% of patients as having high risk, with being identified 45% by PYMS and 44% by STAMP. After adjustment for confounding factors in multivariate regression analysis, patients in the high-risk group had significantly longer median (SD) lengths of stay [medium versus high risk: STRONG KIDS , 9.5 (6.6) versus 15.0 (24.2) days; PYMS, 8.5 (4.4) versus 13.0 (16.1) days; STAMP, 9.0 (5.7) versus 11.0 (17.4) days] and greater median (SD) weight loss [medium versus high risk: STRONG KIDS , 0.15 (0.8) versus -0.35 (0.8) kg; STAMP, 0.5 (0.7) versus 0 (0.1) kg] than patients in the medium-risk group (P < 0.05). The strengths of agreement in the nutritional risk classification between the two observers were good (κ for STRONG KIDS = 0.61; PYMS = 0.79; STAMP = 0.75) (P < 0.01). The STRONG KIDS , PYMS and STAMP tools could be useful and practical for determining which hospitalised children with acute burn injuries will need additional nutritional intervention. © 2017 The British Dietetic Association Ltd.

Direct Laser Writing-Based Programmable Transfer Printing via Bioinspired Shape Memory Reversible Adhesive.

PubMed

Huang, Yin; Zheng, Ning; Cheng, Zhiqiang; Chen, Ying; Lu, Bingwei; Xie, Tao; Feng, Xue

2016-12-28

Flexible and stretchable electronics offer a wide range of unprecedented opportunities beyond conventional rigid electronics. Despite their vast promise, a significant bottleneck lies in the availability of a transfer printing technique to manufacture such devices in a highly controllable and scalable manner. Current technologies usually rely on manual stick-and-place and do not offer feasible mechanisms for precise and quantitative process control, especially when scalability is taken into account. Here, we demonstrate a spatioselective and programmable transfer strategy to print electronic microelements onto a soft substrate. The method takes advantage of automated direct laser writing to trigger localized heating of a micropatterned shape memory polymer adhesive stamp, allowing highly controlled and spatioselective switching of the interfacial adhesion. This, coupled to the proper tuning of the stamp properties, enables printing with perfect yield. The wide range adhesion switchability further allows printing of hybrid electronic elements, which is otherwise challenging given the complex interfacial manipulation involved. Our temperature-controlled transfer printing technique shows its critical importance and obvious advantages in the potential scale-up of device manufacturing. Our strategy opens a route to manufacturing flexible electronics with exceptional versatility and potential scalability.

‘Postage-stamp PIV’: small velocity fields at 400 kHz for turbulence spectra measurements

NASA Astrophysics Data System (ADS)

Beresh, Steven J.; Henfling, John F.; Spillers, Russell W.; Spitzer, Seth M.

2018-03-01

Time-resolved particle image velocimetry recently has been demonstrated in high-speed flows using a pulse-burst laser at repetition rates reaching 50 kHz. Turbulent behavior can be measured at still higher frequencies if the field of view is greatly reduced and lower laser pulse energy is accepted. Current technology allows image acquisition at 400 kHz for sequences exceeding 4000 frames but for an array of only 128  ×  120 pixels, giving the moniker of ‘postage-stamp PIV’. The technique has been tested far downstream of a supersonic jet exhausting into a transonic crossflow. Two-component measurements appear valid until 120 kHz, at which point a noise floor emerges whose magnitude is dependent on the reduction of peak locking. Stereoscopic measurement offers three-component data for turbulent kinetic energy spectra, but exhibits a reduced signal bandwidth and higher noise in the out-of-plane component due to the oblique camera images. The resulting spectra reveal two regions exhibiting power-law dependence describing the turbulent decay. The frequency response of the present measurement configuration exceeds nearly all previous velocimetry measurements in high speed flow.

Improving the Quality of Hot Stamping Parts with Innovative Press Technology and Inline Process Control

NASA Astrophysics Data System (ADS)

Vollmer, R.; Palm, C.

2017-09-01

The increasing number of hot stamped parts in the automotive industry is challenging different process areas. This paper presents a method how to improve the production rates over the whole life cycle of a hot forming part. In the core element of a hot forming line, the hydraulic press, mainly two processing steps are performed. Forming and quenching of the sheet metal part. In addition to the forming operation, it is inevitable to optimize the quenching condition in the bottom dead centre in order to reach a fully martensitic structure and tight geometrical tolerances of the part. Deviations in the blank thickness, tool wear, polishing of classical tools impair the quenching condition and therefore the part quality over the time. A new press and tool design has been developed to counter this effect by providing homogenous contact pressure over the whole die. Especially with a multi cavity tool, the new method is advantageous. Test series have shown that the new tool and press concept can produce parts with a blank thickness of 1.0 mm within 8.0 s cycle time. The so called PCH flex principle makes it possible to produce such high output rates under reliable conditions.

7 CFR 281.4 - Determining Indian tribal organization capability.

Code of Federal Regulations, 2012 CFR

2012-01-01

....4 Section 281.4 Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM ADMINISTRATION OF THE FOOD STAMP PROGRAM ON INDIAN RESERVATIONS § 281.4 Determining Indian tribal organization capability. (a...

7 CFR 281.4 - Determining Indian tribal organization capability.

Code of Federal Regulations, 2013 CFR

2013-01-01

....4 Section 281.4 Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM ADMINISTRATION OF THE FOOD STAMP PROGRAM ON INDIAN RESERVATIONS § 281.4 Determining Indian tribal organization capability. (a...

7 CFR 281.4 - Determining Indian tribal organization capability.

Code of Federal Regulations, 2011 CFR

2011-01-01

....4 Section 281.4 Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM ADMINISTRATION OF THE FOOD STAMP PROGRAM ON INDIAN RESERVATIONS § 281.4 Determining Indian tribal organization capability. (a...

7 CFR 281.4 - Determining Indian tribal organization capability.

Code of Federal Regulations, 2010 CFR

2010-01-01

....4 Section 281.4 Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM ADMINISTRATION OF THE FOOD STAMP PROGRAM ON INDIAN RESERVATIONS § 281.4 Determining Indian tribal organization capability. (a...

7 CFR 276.6 - Good cause.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM STATE AGENCY LIABILITIES AND FEDERAL SANCTIONS § 276.6 Good... affect Program operations; (2) Strikes by State agency staff; (3) Change in the Food Stamp Program or...

7 CFR 275.7 - Selection of sub-units for review.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM PERFORMANCE REPORTING SYSTEM Management Evaluation (ME... Food Stamp Program, exclusive of Post Offices which may issue coupons. Sub-units shall be classified...

27 CFR 479.87 - Cancellation of stamp.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Cancellation of stamp. 479.87 Section 479.87 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES, AND CERTAIN...

27 CFR 479.161 - National Firearms Act stamps.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2011-04-01 2010-04-01 true National Firearms Act stamps. 479.161 Section 479.161 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES...

27 CFR 479.67 - Cancellation of stamp.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2014-04-01 2014-04-01 false Cancellation of stamp. 479.67 Section 479.67 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES, AND CERTAIN...

27 CFR 479.67 - Cancellation of stamp.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2011-04-01 2010-04-01 true Cancellation of stamp. 479.67 Section 479.67 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES, AND CERTAIN...

27 CFR 479.161 - National Firearms Act stamps.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2014-04-01 2014-04-01 false National Firearms Act stamps. 479.161 Section 479.161 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES...

27 CFR 479.67 - Cancellation of stamp.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Cancellation of stamp. 479.67 Section 479.67 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES, AND CERTAIN...

27 CFR 479.161 - National Firearms Act stamps.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2013-04-01 2013-04-01 false National Firearms Act stamps. 479.161 Section 479.161 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES...

27 CFR 479.161 - National Firearms Act stamps.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false National Firearms Act stamps. 479.161 Section 479.161 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES...

27 CFR 479.67 - Cancellation of stamp.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2013-04-01 2013-04-01 false Cancellation of stamp. 479.67 Section 479.67 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES, AND CERTAIN...

27 CFR 479.87 - Cancellation of stamp.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2011-04-01 2010-04-01 true Cancellation of stamp. 479.87 Section 479.87 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES, AND CERTAIN...

27 CFR 479.67 - Cancellation of stamp.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2012-04-01 2010-04-01 true Cancellation of stamp. 479.67 Section 479.67 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES, AND CERTAIN...

27 CFR 479.87 - Cancellation of stamp.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2012-04-01 2010-04-01 true Cancellation of stamp. 479.87 Section 479.87 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES, AND CERTAIN...

27 CFR 479.161 - National Firearms Act stamps.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2012-04-01 2010-04-01 true National Firearms Act stamps. 479.161 Section 479.161 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES...

27 CFR 479.87 - Cancellation of stamp.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2014-04-01 2014-04-01 false Cancellation of stamp. 479.87 Section 479.87 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES, AND CERTAIN...

27 CFR 479.87 - Cancellation of stamp.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2013-04-01 2013-04-01 false Cancellation of stamp. 479.87 Section 479.87 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES, AND CERTAIN...

49 CFR 179.200-24 - Stamping.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR TANK CARS Specifications for Non-Pressure Tank Car Tanks (Classes DOT-111AW and 115AW) § 179.200-24 Stamping. (a) To certify that the tank...

49 CFR 179.200-24 - Stamping.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR TANK CARS Specifications for Non-Pressure Tank Car Tanks (Classes DOT-111AW and 115AW) § 179.200-24 Stamping. (a) To certify that the tank...

49 CFR 179.220-25 - Stamping.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR TANK CARS Specifications for Non-Pressure Tank Car Tanks (Classes DOT-111AW and 115AW) § 179.220-25 Stamping. (a) To certify that the tank...

49 CFR 179.200-24 - Stamping.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR TANK CARS Specifications for Non-Pressure Tank Car Tanks (Classes DOT-111AW and 115AW) § 179.200-24 Stamping. (a) To certify that the tank...

7 CFR 283.3 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Indian tribe determined by the Secretary to be capable of effectively administering a Food Stamp Program... Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM APPEALS OF QUALITY CONTROL (âQCâ) CLAIMS General § 283.3...

7 CFR 277.16 - Suspension, disallowance and program closeout.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Section 277.16 Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM PAYMENTS OF CERTAIN..., temporarily withhold some or all Federal reimbursements for costs of administration of the Food Stamp Program...

7 CFR 283.3 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Indian tribe determined by the Secretary to be capable of effectively administering a Food Stamp Program... Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM APPEALS OF QUALITY CONTROL (âQCâ) CLAIMS General § 283.3...

46. DETAIL OF UPPER STAMP BATTERIES CAMS, TAPPETS, STEMS, AND ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

46. DETAIL OF UPPER STAMP BATTERIES CAMS, TAPPETS, STEMS, AND RELATIONSHIP OF BULL WHEEL (LOWER RIGHT) LOOKING NORTH NORTHEAST. SEE CA-290-22 FOR A SIMILAR B&W NEGATIVE. - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

Prevention of crack in stretch flanging process using hot stamping technique

NASA Astrophysics Data System (ADS)

Syafiq, Y. Mohd; Hamedon, Z.; Azila Aziz, Wan; Razlan Yusoff, Ahmad

2017-10-01

Demand for enhancing of passenger safety as well as weight reduction of automobiles has increased the use of high strength steel sheets. As a sheet metal is a lightweight having high strength is suitable for producing automotive parts such as white body panel. The stretch flanging of the high strength steel sheet is a problem due to high springback and easy to crack. This study uses three methods to stretch flange the sheets; using lubricants, shear-edge polishing and hot stamping. The effectiveness of these methods will be measured by comparing the flange length of each methods can achieved. For stretch flange with lubricant and polished sheared edge, the flange length failed to achieve the target 15 mm while hot stamping improved the formability of the sheet and preventing the occurrence of the springback and crack. Hot stamping not only improved formability of the sheet but also transformed the microstructure into martensite thus improve the hardness and the strength of the sheet after been quenched with the dies.

Large Area Nano-transfer Printing of Sub-50-nm Metal Nanostructures Using Low-cost Semi-flexible Hybrid Templates

NASA Astrophysics Data System (ADS)

Nagel, Robin D.; Haeberle, Tobias; Schmidt, Morten; Lugli, Paolo; Scarpa, Giuseppe

2016-03-01

In this work, we present a method for printing metal micro- and nanopatterns down to sub-50-nm feature sizes using replicated, defect-tolerant stamps made out of OrmoStamp®; material. The relevant parameters for a successful transfer over large areas were investigated and yields above 99 % have been achieved. Comparing our results to conventional nano-transfer printing using PDMS stamps, we find that the more rigid hybrid polymer used here prevents unintended transfer from interspaces between structures of large distance due to roof collapse and deformation of nano-sized structures due to lateral collapse. Yet, our stamps are flexible enough to ensure intimate contact with the underlying substrate over large areas even in the presence of defect particles. Additionally, the presented patterning technique is resist-, solvent-, and chemical-free and is therefore ideally suited for applications in organic nanoelectronics where standard nanostructuring methods can harm or destroy the organic material.

Mercury MESSENGER Stamp Unveiling

NASA Image and Video Library

2011-05-03

From left, NASA Deputy Director, Planetary Science Division, Science Mission Directorate, Jim Adams, NASA Kennedy Space Center Director of Education and External Relations Cheryl Hurst, United States Postal Service Vice President of Finance Steve Masse, NASA Mercury Astronaut Scott Carpenter, NASA Administrator Charles Boldin, Daughters of NASA astronaut Alan Shepard, Alice Wackermann, Laura Shepard Churchley, and Julie Jenkins, and NASA Kennedy Space Center Director Robert Cabana pose for a photograph during an unveiling ceremony of two USPS stamps that commemorate and celebrate 50 years of US Spaceflight and the MESSENGER program during an event, Wednesday, May 4, 2011 at the NASA Kennedy Space Center in Cape Canaveral, Fla. One stamp commemorates NASA’s Project Mercury, America’s first manned spaceflight program, and NASA astronaut Alan Shepard’s historic flight on May 5, 1961, aboard spacecraft Freedom 7. The other stamp draws attention to NASA’s unmanned MESSENGER mission, a scientific investigation of the planet Mercury. On March 17, 2011, MESSENGER became the first spacecraft to enter into orbit around Mercury. Photo Credit: (NASA/Bill Ingalls)

7 CFR 273.20 - SSI cash-out.

Code of Federal Regulations, 2010 CFR

2010-01-01

... specifically increased to include the value of the food stamp allotment. (b) Receipt of SSI benefits. In... Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM CERTIFICATION OF ELIGIBLE HOUSEHOLDS § 273.20 SSI cash-out. (a...

27 CFR 479.163 - Reuse of stamps prohibited.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2012-04-01 2010-04-01 true Reuse of stamps prohibited. 479.163 Section 479.163 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES, AND...

27 CFR 479.163 - Reuse of stamps prohibited.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Reuse of stamps prohibited. 479.163 Section 479.163 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES, AND...

27 CFR 479.163 - Reuse of stamps prohibited.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2013-04-01 2013-04-01 false Reuse of stamps prohibited. 479.163 Section 479.163 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES, AND...

27 CFR 479.163 - Reuse of stamps prohibited.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2011-04-01 2010-04-01 true Reuse of stamps prohibited. 479.163 Section 479.163 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES, AND...

27 CFR 479.163 - Reuse of stamps prohibited.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2014-04-01 2014-04-01 false Reuse of stamps prohibited. 479.163 Section 479.163 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES, AND...

7 CFR 273.12 - Requirements for change reporting households.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Section 273.12 Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM CERTIFICATION OF ELIGIBLE... assistance (GA) in project areas in which GA and food stamp cases are jointly processed. The State agency is...

76 FR 30893 - Periodic Reporting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-27

... proportion to total ODIS-RPW sampling revenue. Petition, Supporting Material, at 3-6. The Postal Service... products by distributing PIHOP stamp adjustments in proportion to ODIS-RPW sampling stamp revenue and PIHOP meter adjustments in proportion to ODIS-RPW sampling meter revenue. Id. at 9. The details of the rather...

Less is (sometimes) more in cognitive engineering: the role of automation technology in improving patient safety

PubMed Central

Vicente, K

2003-01-01



 There is a tendency to assume that medical error can be stamped out by automation. Technology may improve patient safety, but cognitive engineering research findings in several complex safety critical systems, including both aviation and health care, show that more is not always better. Less sophisticated technological systems can sometimes lead to better performance than more sophisticated systems. This "less is more" effect arises because safety critical systems are open systems where unanticipated events are bound to occur. In these contexts, decision support provided by a technological aid will be less than perfect because there will always be situations that the technology cannot accommodate. Designing sophisticated automation that suggests an uncertain course of action seems to encourage people to accept the imperfect advice, even though information to decide independently on a better course of action is available. It may be preferable to create more modest designs that merely provide feedback about the current state of affairs or that critique human generated solutions than to rush to automate by creating sophisticated technological systems that recommend (fallible) courses of action. PMID:12897363

Precision forging technology for aluminum alloy

NASA Astrophysics Data System (ADS)

Deng, Lei; Wang, Xinyun; Jin, Junsong; Xia, Juchen

2018-03-01

Aluminum alloy is a preferred metal material for lightweight part manufacturing in aerospace, automobile, and weapon industries due to its good physical properties, such as low density, high specific strength, and good corrosion resistance. However, during forging processes, underfilling, folding, broken streamline, crack, coarse grain, and other macro- or microdefects are easily generated because of the deformation characteristics of aluminum alloys, including narrow forgeable temperature region, fast heat dissipation to dies, strong adhesion, high strain rate sensitivity, and large flow resistance. Thus, it is seriously restricted for the forged part to obtain precision shape and enhanced property. In this paper, progresses in precision forging technologies of aluminum alloy parts were reviewed. Several advanced precision forging technologies have been developed, including closed die forging, isothermal die forging, local loading forging, metal flow forging with relief cavity, auxiliary force or vibration loading, casting-forging hybrid forming, and stamping-forging hybrid forming. High-precision aluminum alloy parts can be realized by controlling the forging processes and parameters or combining precision forging technologies with other forming technologies. The development of these technologies is beneficial to promote the application of aluminum alloys in manufacturing of lightweight parts.

Stamping Die Making. 439-318/320.

ERIC Educational Resources Information Center

Yunke, P.; And Others

Each unit in this curriculum guide on stamping die making contains an introduction, objectives, materials required, lessons, space for notes, figures, and diagrams. There are 29 units in this guide, dealing with the following topics: EZ-MILL programming; EZ-MILL BATT; print of punch and EZ-MILL part programming; download to Computer Numerical…

9 CFR 327.10 - Samples; inspection of consignments; refusal of entry; marking.

Code of Federal Regulations, 2010 CFR

2010-01-01

... import establishment and approved by the Director, Import Inspection Division, is on file at the import... (iv) That the establishment will maintain a daily stamping log containing the following information... covering the product to be inspected. The daily stamping log must be retained by the establishment in...

9 CFR 327.10 - Samples; inspection of consignments; refusal of entry; marking.

Code of Federal Regulations, 2011 CFR

2011-01-01

... import establishment and approved by the Director, Import Inspection Division, is on file at the import... (iv) That the establishment will maintain a daily stamping log containing the following information... covering the product to be inspected. The daily stamping log must be retained by the establishment in...

27 CFR 479.171 - Redemption of or allowance for stamps.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2012-04-01 2010-04-01 true Redemption of or allowance for stamps. 479.171 Section 479.171 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES...

27 CFR 479.171 - Redemption of or allowance for stamps.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2014-04-01 2014-04-01 false Redemption of or allowance for stamps. 479.171 Section 479.171 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES...

27 CFR 479.171 - Redemption of or allowance for stamps.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2013-04-01 2013-04-01 false Redemption of or allowance for stamps. 479.171 Section 479.171 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES...

27 CFR 479.171 - Redemption of or allowance for stamps.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2011-04-01 2010-04-01 true Redemption of or allowance for stamps. 479.171 Section 479.171 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES...

27 CFR 479.171 - Redemption of or allowance for stamps.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Redemption of or allowance for stamps. 479.171 Section 479.171 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES...

9 CFR 327.1 - Definitions; application of provisions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... point at which an official of the Canadian meat inspection system contacts the Import Field Office for... containers are marked with the Canadian port stamp and upon the filing of Customs Form 7533 at the port of... with the Canadian export stamp and the foreign inspection certificate accompanying the product is...

31 CFR 315.56 - General instructions and liability.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 31 Money and Finance: Treasury 2 2010-07-01 2010-07-01 false General instructions and liability. 315.56 Section 315.56 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued... and, where one is available, a corporate stamp or issuing or paying agent's stamp. (b) Liability. The...

15 CFR Appendix B to Part 30 - AES Filing Codes

Code of Federal Regulations, 2011 CFR

2011-01-01

... exemptions: Currency Airline tickets Bank notes Internal revenue stamps State liquor stamps Advertising...—Trans-Alaska Pipeline Authorization Act C50ENC—Encryption Commodities and Software C51AGR—License Exception Agricultural Commodities C53APP—Adjusted Peak Performance (Computers) C54SS-WRC—Western Red Cedar...

15 CFR Appendix B to Part 30 - AES Filing Codes

Code of Federal Regulations, 2010 CFR

2010-01-01

... exemptions: Currency Airline tickets Bank notes Internal revenue stamps State liquor stamps Advertising...—Trans-Alaska Pipeline Authorization Act C50ENC—Encryption Commodities and Software C51AGR—License Exception Agricultural Commodities C53APP—Adjusted Peak Performance (Computers) C54SS-WRC—Western Red Cedar...

Computer Graphics: KidPix, the MacIntosh, and Students with Cognitive Disorders.

ERIC Educational Resources Information Center

Olson, Cindy

This teacher's guide provides an overview of KidPix software and contains adaptive applications of the software for Cognitively Disabled-Borderline (CDB) students. Ten lesson plans are given, including: (1) "USing Rubber Stamps/Rubber Stamp Editor"; (2) "Portrait"; (3) "Create a Pattern"; (4) "Garden Mural";…

PRESS SHOP. SEVEN BLISS PRESSES STAMP OUT A VARIETY OF ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

PRESS SHOP. SEVEN BLISS PRESSES STAMP OUT A VARIETY OF CARTRIDGE AND SHELL CASINGS. THIS DEPARTMENT WAS TRANSFORMED FROM A MONEY-LOSING OPERATION TO A PROFIT CENTER UNDER THE FIRST WORKER-MANAGED QUALITY CIRCLE IN THE PLANT. - American Brass Foundry, 70 Sayre Street, Buffalo, Erie County, NY

MERCURY IN STAMP SAND DISCHARGES: IMPLICATIONS FOR LAKE SUPERIOR MERCURY CYCLING

EPA Science Inventory

Approximately a half billion tons of waste rock from the extraction of native copper and silver ores was discharged into the Lake Superior basin. Stamping was the method of choice to recover these metals from the surrounding poor rock. This process created large amounts of extre...

Lightweight Steel Solutions for Automotive Industry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Hong Woo; Kim, Gyosung; Park, Sung Ho

2010-06-15

Recently, improvement in fuel efficiency and safety has become the biggest issue in worldwide automotive industry. Although the regulation of environment and safety has been tightened up more and more, the majority of vehicle bodies are still manufactured from stamped steel components. This means that the optimized steel solutions enable to demonstrate its ability to reduce body weight with high crashworthiness performance instead of expensive light weight materials such as Al, Mg and composites. To provide the innovative steel solutions for automotive industry, POSCO has developed AHSS and its application technologies, which is directly connected to EVI activities. EVI ismore » a technical cooperation program with customer covering all stages of new car project from design to mass production. Integrated light weight solutions through new forming technologies such as TWB, hydroforming and HPF are continuously developed and provided for EVI activities. This paper will discuss the detailed status of these technologies especially light weight steel solutions based on innovative technologies.« less

Self-supporting hydrogel stamps for the microcontact printing of proteins.

PubMed

Coq, Naïs; van Bommel, Ties; Hikmet, Rifat A; Stapert, Hendrik R; Dittmer, Wendy U

2007-04-24

In this work we explore a new hydrogel stamp material obtained from polymerizing 2-hydroxyethyl acrylate and poly(ethylene glycol) diacrylate in the presence of water for the microcontact printing of proteins directly on gold substrates and by covalent coupling to self-assembled monolayers of alkanethiols. At high cross-link density, the hydrogel is rigid, hydrophilic, and with a high buffer holding capacity to enable the unsupported printing of protein patterns homogeneously and reproducibly, with micrometer-range precision. The stamps were used to print antibodies to human parathyroid hormone, which were shown using immunoassay tests to retain their biological function with binding capacities comparable to those of solution-adsorbed antibodies.

Comparison of laser regimes for stamp cleaning

NASA Astrophysics Data System (ADS)

Radvan, Roxana N.; Dan, Suzana; Popovici, Nicoleta; Striber, J.; Savastru, Dan; Savastru, Roxana

2001-10-01

This paper presents a comparative study of the laser cleaning regimes applied to colored substrates with various chromatic characteristics, including colored paper and printed paper with different dpi (dots per inch) values. Tests are done under microscope with high precision techniques, using controlled Nd:YAG laser. The wavelength preponderantly used in the experiments is the Nd:YAG fundamental regime (1064 nm). Parallel experiments at 532 nm have been developed on difficult cases, or when the results were not satisfactory with 1064 nm. The main part of the work presents some results on stamp cleaning. Experimental results indicate that cleaning efficiency is correlated with the color of substrate, age of the ink on the stamp, color quality and paper quality.

Characterization of TimepixCam, a fast imager for the time-stamping of optical photons

NASA Astrophysics Data System (ADS)

Nomerotski, Andrei; Chakaberia, I.; Fisher-Levine, M.; Janoska, Z.; Takacs, P.; Tsang, T.

2017-01-01

We describe the characterization of TimepixCam, a novel camera used to time-stamp optical photons. The camera employs a specialized silicon sensor with a thin entrance window, read out by a Timepix ASIC. TimepixCam is able to record and time-stamp light flashes exceeding 1,000 photons with 15 ns time resolution. Specially produced photodiodes were used to evaluate the quantum efficiency, which was determined to be higher than 90% in the wavelength range of 430-900 nm. The quantum efficiency, sensitivity and ion detection efficiency were compared for a variety of sensors with different surface treatments. Sensors with the thinnest window, 50 nm, had the best performance.

KSC-2011-3296

NASA Image and Video Library

2011-05-04

CAPE CANAVERAL, Fla. -- In the Rocket Garden at NASA's Kennedy Space Center Visitor Complex in Florida, Laura Churchley (left), Alice Wackerman and Julie Jenkins, daughters of Mercury Astronaut Alan Shepard, applaud during an event unveiling two new stamps to commemorate the 50th anniversary of human spaceflight from the United States Postal Service. One stamp commemorates NASA's Project Mercury and Alan Shepard's historic launch on May 5, 1961, aboard the spacecraft Freedom 7. The second stamp honors NASA's MESSENGER, which reached Mercury in March to become the first spacecraft to orbit the planet. The two missions frame a remarkable 50-year period in which America advanced space exploration through more than 1,500 crewed and uncrewed flights. Photo credit: NASA/Kim Shiflett

76 FR 68263 - Migratory Bird Subsistence Harvest in Alaska; Harvest Regulations for Migratory Birds in Alaska...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-03

... support by quantitative information or studies and those that include citations to, and analyses of, the... included the duck stamp requirement. The representative indicated that there was a conflict in the... to the Federal duck stamp requirement and that he does not support any regulation requiring the...

1. VIEW, LOOKING WEST, AT THE SITE OF THE PINE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. VIEW, LOOKING WEST, AT THE SITE OF THE PINE LOG MILL. THE STONE RETAINING WALL ON THE RIGHT MARKS THE LOCATION OF THE 1896 20-STAMP FACILITY, EXPANDED SOUTH TO INCLUDE 20 ADDITIONAL STAMPS BY 1899 - Pine Log Mill, Southern Edge of Salt Spring Valley, Copperopolis, Calaveras County, CA

19 CFR 11.3 - Package and notice requirements for cigars and cigarettes; package requirements for cigarette...

Code of Federal Regulations, 2013 CFR

2013-04-01

... cigarettes; package requirements for cigarette papers and tubes. 11.3 Section 11.3 Customs Duties U.S... STAMPING; MARKING Packing and Stamping § 11.3 Package and notice requirements for cigars and cigarettes; package requirements for cigarette papers and tubes. Exemptions from tax on cigars, cigarettes, and...

19 CFR 11.3 - Package and notice requirements for cigars and cigarettes; package requirements for cigarette...

Code of Federal Regulations, 2011 CFR

2011-04-01

... cigarettes; package requirements for cigarette papers and tubes. 11.3 Section 11.3 Customs Duties U.S... STAMPING; MARKING Packing and Stamping § 11.3 Package and notice requirements for cigars and cigarettes; package requirements for cigarette papers and tubes. Exemptions from tax on cigars, cigarettes, and...

Studying the Solar System Can Be More than Just "Stamp Collecting"

ERIC Educational Resources Information Center

LoPresto, Michael C.

2017-01-01

While teaching his first-ever introductory college astronomy course, I heard a graduate student make the comment that compared to other areas of astronomy, studying the solar system is just "stamp collecting." Coverage of the solar system in an introductory college astronomy course certainly "could" consist mostly of showing…

27 CFR 479.37 - Certificates in lieu of stamps lost or destroyed.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2011-04-01 2010-04-01 true Certificates in lieu of stamps lost or destroyed. 479.37 Section 479.37 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE...

27 CFR 479.37 - Certificates in lieu of stamps lost or destroyed.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2012-04-01 2010-04-01 true Certificates in lieu of stamps lost or destroyed. 479.37 Section 479.37 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE...

27 CFR 479.37 - Certificates in lieu of stamps lost or destroyed.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2014-04-01 2014-04-01 false Certificates in lieu of stamps lost or destroyed. 479.37 Section 479.37 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE...

27 CFR 479.37 - Certificates in lieu of stamps lost or destroyed.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2013-04-01 2013-04-01 false Certificates in lieu of stamps lost or destroyed. 479.37 Section 479.37 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE...

27 CFR 479.37 - Certificates in lieu of stamps lost or destroyed.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Certificates in lieu of stamps lost or destroyed. 479.37 Section 479.37 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE...

Food Stamp Recipients Eat More Vegetables after Viewing Nutrition Videos.

ERIC Educational Resources Information Center

Joy, Amy Block; Feldman, Nancy; Fujii, Mary Lavender; Garcia, Linda; Hudes, Mark; Mitchell, Rita; Bunch, Sybille; Metz, Diane

1999-01-01

A study in three California counties found that food stamp recipients who viewed a videotape promoting vegetables had increased their knowledge of vegetables and greatly increased their consumption of potatoes and raw vegetables two to six weeks later. The feasibility of using videotaped nutrition instruction with low-income adults is discussed.…

19 CFR 11.6 - Distilled spirits, wines, and malt liquors in bulk.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., and malt liquors in bulk. (a) The port director, in his discretion, may require marks, brands, stamps..., brands, stamps, labels, or similar devices required by Federal, State, or local statute or regulation may... measurement shall be done at a public store, warehouse, or other appropriate facility. (c) Marks, brands...

75 FR 11913 - Chrysler, LLC; Warren Stamping Plant, Including On-Site Leased Workers From Caravan Knight...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-12

... Stamping Plant, Including On-Site Leased Workers From Caravan Knight Facilities Management LLC; Warren, MI... from Caravan Knight Facilities Management LLC were employed on-site at the Warren, Michigan location of... Department is amending this certification to include workers leased from Caravan Knight Facilities Management...

7 CFR 281.5 - Responsibilities of an Indian tribal organization designated as State agency.

Code of Federal Regulations, 2011 CFR

2011-01-01

... (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM ADMINISTRATION OF THE FOOD STAMP PROGRAM ON INDIAN RESERVATIONS § 281.5 Responsibilities of an Indian tribal... 7 Agriculture 4 2011-01-01 2011-01-01 false Responsibilities of an Indian tribal organization...

The Contingent Use of Trading Stamps in Reducing Truancy: A Case Report.

ERIC Educational Resources Information Center

Zweig, John T.; And Others

1979-01-01

A 13-year-old learning-disabled subject received a daily amount of trading stamps contingent on school attendance. Results showed a significant decrease in truancy from three to four days per week to less than one. A reversal design indicated that truancy could be controlled by the contingency procedure. (Author/GDC)

77 FR 24177 - Approval for Manufacturing Authority; Foreign-Trade Zone 177; Hoosier Stamping & Mfg. Corp...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-23

... DEPARTMENT OF COMMERCE Foreign-Trade Zones Board [Order No. 1822] Approval for Manufacturing Authority; Foreign-Trade Zone 177; Hoosier Stamping & Mfg. Corp. (Wheel Assemblies and Accessories); Chandler, IN Pursuant to its authority under the Foreign-Trade Zones Act of June 18, 1934, as amended (19 U...

8 CFR 1212.6 - Border crossing identification cards.

Code of Federal Regulations, 2014 CFR

2014-01-01

... seeks to travel temporarily to the United States for business or pleasure without a visa and passport... similar stamp in a passport). (i) A Canadian citizen or other person sharing common nationality with... similar stamp in a passport) issued by the DOS prior to April 1, 1998, that does not contain a machine...

8 CFR 212.6 - Border crossing identification cards.

Code of Federal Regulations, 2012 CFR

2012-01-01

... or pleasure without a visa and passport, must apply to the DOS on Form DS-156, Visitor Visa... border crossing card (or similar stamp in a passport). (i) A Canadian citizen or other person sharing... crossing card (or similar stamp in a passport) issued by the DOS prior to April 1, 1998, that does not...

8 CFR 212.6 - Border crossing identification cards.

Code of Federal Regulations, 2013 CFR

2013-01-01

... or pleasure without a visa and passport, must apply to the DOS on Form DS-156, Visitor Visa... border crossing card (or similar stamp in a passport). (i) A Canadian citizen or other person sharing... crossing card (or similar stamp in a passport) issued by the DOS prior to April 1, 1998, that does not...

8 CFR 1212.6 - Border crossing identification cards.

Code of Federal Regulations, 2010 CFR

2010-01-01

... seeks to travel temporarily to the United States for business or pleasure without a visa and passport... similar stamp in a passport). (i) A Canadian citizen or other person sharing common nationality with... similar stamp in a passport) issued by the DOS prior to April 1, 1998, that does not contain a machine...

8 CFR 1212.6 - Border crossing identification cards.

Code of Federal Regulations, 2012 CFR

2012-01-01

... seeks to travel temporarily to the United States for business or pleasure without a visa and passport... similar stamp in a passport). (i) A Canadian citizen or other person sharing common nationality with... similar stamp in a passport) issued by the DOS prior to April 1, 1998, that does not contain a machine...

8 CFR 212.6 - Border crossing identification cards.

Code of Federal Regulations, 2011 CFR

2011-01-01

... or pleasure without a visa and passport, must apply to the DOS on Form DS-156, Visitor Visa... border crossing card (or similar stamp in a passport). (i) A Canadian citizen or other person sharing... crossing card (or similar stamp in a passport) issued by the DOS prior to April 1, 1998, that does not...

22 CFR 41.113 - Procedures in issuing visas.

Code of Federal Regulations, 2013 CFR

2013-04-01

.... (a) Visa evidenced by stamp placed in passport. Except as provided in paragraphs (b) of this section, a nonimmigrant visa shall be evidenced by a visa stamp placed in the alien's passport. The... visa. (b) Cases in which visa not placed in passport. In the following cases the visa shall be placed...

8 CFR 1212.6 - Border crossing identification cards.

Code of Federal Regulations, 2011 CFR

2011-01-01

... seeks to travel temporarily to the United States for business or pleasure without a visa and passport... similar stamp in a passport). (i) A Canadian citizen or other person sharing common nationality with... similar stamp in a passport) issued by the DOS prior to April 1, 1998, that does not contain a machine...

22 CFR 41.113 - Procedures in issuing visas.

Code of Federal Regulations, 2012 CFR

2012-04-01

.... (a) Visa evidenced by stamp placed in passport. Except as provided in paragraphs (b) of this section, a nonimmigrant visa shall be evidenced by a visa stamp placed in the alien's passport. The... visa. (b) Cases in which visa not placed in passport. In the following cases the visa shall be placed...

22 CFR 41.113 - Procedures in issuing visas.

Code of Federal Regulations, 2010 CFR

2010-04-01

.... (a) Visa evidenced by stamp placed in passport. Except as provided in paragraphs (b) of this section, a nonimmigrant visa shall be evidenced by a visa stamp placed in the alien's passport. The... visa. (b) Cases in which visa not placed in passport. In the following cases the visa shall be placed...

8 CFR 212.6 - Border crossing identification cards.

Code of Federal Regulations, 2010 CFR

2010-01-01

... or pleasure without a visa and passport, must apply to the DOS on Form DS-156, Visitor Visa... border crossing card (or similar stamp in a passport). (i) A Canadian citizen or other person sharing... crossing card (or similar stamp in a passport) issued by the DOS prior to April 1, 1998, that does not...

8 CFR 212.6 - Border crossing identification cards.

Code of Federal Regulations, 2014 CFR

2014-01-01

... or pleasure without a visa and passport, must apply to the DOS on Form DS-156, Visitor Visa... border crossing card (or similar stamp in a passport). (i) A Canadian citizen or other person sharing... crossing card (or similar stamp in a passport) issued by the DOS prior to April 1, 1998, that does not...

8 CFR 1212.6 - Border crossing identification cards.

Code of Federal Regulations, 2013 CFR

2013-01-01

... seeks to travel temporarily to the United States for business or pleasure without a visa and passport... similar stamp in a passport). (i) A Canadian citizen or other person sharing common nationality with... similar stamp in a passport) issued by the DOS prior to April 1, 1998, that does not contain a machine...

22 CFR 41.113 - Procedures in issuing visas.

Code of Federal Regulations, 2014 CFR

2014-04-01

.... (a) Visa evidenced by stamp placed in passport. Except as provided in paragraphs (b) of this section, a nonimmigrant visa shall be evidenced by a visa stamp placed in the alien's passport. The... visa. (b) Cases in which visa not placed in passport. In the following cases the visa shall be placed...

22 CFR 41.113 - Procedures in issuing visas.

Code of Federal Regulations, 2011 CFR

2011-04-01

.... (a) Visa evidenced by stamp placed in passport. Except as provided in paragraphs (b) of this section, a nonimmigrant visa shall be evidenced by a visa stamp placed in the alien's passport. The... visa. (b) Cases in which visa not placed in passport. In the following cases the visa shall be placed...

46 CFR 53.10-1 - General.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false General. 53.10-1 Section 53.10-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING HEATING BOILERS Tests, Inspection, Stamping, and Reporting (Article 5) § 53.10-1 General. The tests, inspection, stamping, and reporting of heating boilers shall be as indicated in Articl...

46 CFR 53.10-1 - General.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false General. 53.10-1 Section 53.10-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING HEATING BOILERS Tests, Inspection, Stamping, and Reporting (Article 5) § 53.10-1 General. The tests, inspection, stamping, and reporting of heating boilers shall be as indicated in Articl...

46 CFR 53.10-1 - General.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false General. 53.10-1 Section 53.10-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING HEATING BOILERS Tests, Inspection, Stamping, and Reporting (Article 5) § 53.10-1 General. The tests, inspection, stamping, and reporting of heating boilers shall be as indicated in articl...

46 CFR 53.10-1 - General.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false General. 53.10-1 Section 53.10-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING HEATING BOILERS Tests, Inspection, Stamping, and Reporting (Article 5) § 53.10-1 General. The tests, inspection, stamping, and reporting of heating boilers shall be as indicated in Articl...

46 CFR 53.10-1 - General.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false General. 53.10-1 Section 53.10-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING HEATING BOILERS Tests, Inspection, Stamping, and Reporting (Article 5) § 53.10-1 General. The tests, inspection, stamping, and reporting of heating boilers shall be as indicated in articl...

75 FR 32119 - Proposed Amendment of the Pacific High and Low Offshore Airspace Areas; California

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-07

... action must submit with those comments a self-addressed, stamped postcard on which the following... postcard will be date/time stamped and returned to the commenter. All communications received on or before... the current location to the Mexico Flight Information Region (FIR), will allow the application of...

19 CFR 11.3 - Package and notice requirements for cigars and cigarettes; package requirements for cigarette...

Code of Federal Regulations, 2014 CFR

2014-04-01

... cigarettes; package requirements for cigarette papers and tubes. 11.3 Section 11.3 Customs Duties U.S... STAMPING; MARKING Packing and Stamping § 11.3 Package and notice requirements for cigars and cigarettes; package requirements for cigarette papers and tubes. Exemptions from tax on cigars, cigarettes, and...

19 CFR 11.3 - Package and notice requirements for cigars and cigarettes; package requirements for cigarette...

Code of Federal Regulations, 2010 CFR

2010-04-01

... cigarettes; package requirements for cigarette papers and tubes. 11.3 Section 11.3 Customs Duties U.S... STAMPING; MARKING Packing and Stamping § 11.3 Package and notice requirements for cigars and cigarettes; package requirements for cigarette papers and tubes. Exemptions from tax on cigars, cigarettes, and...

19 CFR 11.3 - Package and notice requirements for cigars and cigarettes; package requirements for cigarette...

Code of Federal Regulations, 2012 CFR

2012-04-01

... cigarettes; package requirements for cigarette papers and tubes. 11.3 Section 11.3 Customs Duties U.S... STAMPING; MARKING Packing and Stamping § 11.3 Package and notice requirements for cigars and cigarettes; package requirements for cigarette papers and tubes. Exemptions from tax on cigars, cigarettes, and...

Stamping Out Rubber-Stamp Collegiality

ERIC Educational Resources Information Center

Bugeja, Michael J.

2012-01-01

In the past year, public colleges and universities across the country have been shrinking degree programs and terminating personnel--including tenured professors--in an effort to cope with budget cuts in higher education. The situation is not confined to a handful of mismanaged public institutions, as in the past. It is a national phenomenon and…

Impacting Mediators of Change for Physical Activity among Elderly Food Stamp Recipients

ERIC Educational Resources Information Center

Dye, Cheryl J.; Williams, Joel E.; Kemper, Karen A.; McGuire, Francis A.; Aybar-Damali, Begum

2012-01-01

A multidisciplinary team developed and pilot-tested a curriculum, delivered by trained lay educators, to increase self-efficacy for physical activity among elderly food stamp recipients. Curriculum development was guided by a comprehensive literature review. Process evaluation was used to revise the curriculum and to assess lay educator training…

Adinkra Banners

ERIC Educational Resources Information Center

Gomez, Aurelia

2009-01-01

Adinkra cloth is a stamped fabric that is made in Ghana, Africa. Symbolic motifs that represent proverbs are carved from calabashes, a type of gourd, and are dipped into a black dye made from the bark of the badie tree. Adinkra artists divide the fabric into squares and create patterns and repetitive designs using the inked stamps. When it is used…

46 CFR 78.36-20 - Shipboard inspections.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS OPERATIONS Work Vests § 78.36-20 Shipboard inspections. (a) Each work vest shall be subject to examination by a marine... shall not be stamped by a marine inspector with a Coast Guard stamp. If a work vest is found not to be...

46 CFR 78.36-20 - Shipboard inspections.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS OPERATIONS Work Vests § 78.36-20 Shipboard inspections. (a) Each work vest shall be subject to examination by a marine... shall not be stamped by a marine inspector with a Coast Guard stamp. If a work vest is found not to be...

46 CFR 78.36-20 - Shipboard inspections.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS OPERATIONS Work Vests § 78.36-20 Shipboard inspections. (a) Each work vest shall be subject to examination by a marine... shall not be stamped by a marine inspector with a Coast Guard stamp. If a work vest is found not to be...

46 CFR 78.36-20 - Shipboard inspections.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS OPERATIONS Work Vests § 78.36-20 Shipboard inspections. (a) Each work vest shall be subject to examination by a marine... shall not be stamped by a marine inspector with a Coast Guard stamp. If a work vest is found not to be...

46 CFR 78.36-20 - Shipboard inspections.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS OPERATIONS Work Vests § 78.36-20 Shipboard inspections. (a) Each work vest shall be subject to examination by a marine... shall not be stamped by a marine inspector with a Coast Guard stamp. If a work vest is found not to be...

Whom Shall We Put on the Postage Stamps?

ERIC Educational Resources Information Center

Boyle, Roger D.

2013-01-01

We consider the emergence of "notables" within the disciplines of the modern university, the foremost among whom may be selected to appear on postage stamps. Noting that disciplinary culture is as important as content in university education, we suggest that some knowledge of the identity of these notables, passed on by encultured tutors, should…

Pixel Palette: Put Your Stamp on It.

ERIC Educational Resources Information Center

Osterer, Irv

1998-01-01

Describes a project used in a senior information design class where the students created their own self-portraits on rubber stamps through the use of Photoshop and QuarkXPress. Explains that the students learned about the difference between line art and continuous tone images as well as the effects of printing ink and papers. (CMK)

Over-the-counter sales of out-of-state and counterfeit tax stamp cigarettes in New York City.

PubMed

Silver, Diana; Giorgio, Margaret M; Bae, Jin Yung; Jimenez, Geronimo; Macinko, James

2016-09-01

New York City (NYC) has strict minimum cigarette price and tax stamp laws, but evidence regarding the extent of evasion of such laws in over-the-counter sales is scarce. 830 packs were purchased at licensed tobacco retailers at 92 randomly selected neighbourhoods in NYC in spring and fall 2014, following the establishment of NYC's minimum price law. The χ(2) analyses of illegal tax stamps on pack, by retailer type and data collection period, are presented. Over 15% of packs purchased had out-of-state (4.5%) or counterfeit tax stamps (10.6%). Purchases resulted in at least one illegal pack obtained in 70% of neighbourhoods, largely from independent stores. In 21.5% of sampled neighbourhoods, it was possible to purchase an illegal pack each collection period. Enhanced enforcement of retail sales of cigarettes is needed to ensure the full benefit of existing tobacco control laws in NYC. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Prediction of Proper Temperatures for the Hot Stamping Process Based on the Kinetics Models

NASA Astrophysics Data System (ADS)

Samadian, P.; Parsa, M. H.; Mirzadeh, H.

2015-02-01

Nowadays, the application of kinetics models for predicting microstructures of steels subjected to thermo-mechanical treatments has increased to minimize direct experimentation, which is costly and time consuming. In the current work, the final microstructures of AISI 4140 steel sheets after the hot stamping process were predicted using the Kirkaldy and Li kinetics models combined with new thermodynamically based models in order for the determination of the appropriate process temperatures. In this way, the effect of deformation during hot stamping on the Ae3, Acm, and Ae1 temperatures was considered, and then the equilibrium volume fractions of phases at different temperatures were calculated. Moreover, the ferrite transformation rate equations of the Kirkaldy and Li models were modified by a term proposed by Åkerström to consider the influence of plastic deformation. Results showed that the modified Kirkaldy model is satisfactory for the determination of appropriate austenitization temperatures for the hot stamping process of AISI 4140 steel sheets because of agreeable microstructure predictions in comparison with the experimental observations.

Risks of undernutrition and malnutrition in hospitalized pediatric patients with spinal cord injury.

PubMed

Wang, Y-J; Zhou, H-J; Liu, P-J; Liu, G-L; Zheng, Y; Wei, B; Hao, C-X; Zhang, Y; Kang, H-Q; Lu, X-L; Yuan, Y

2017-03-01

Prospective study. To describe the nutritional risk/status of Chinese children with spinal cord injury (SCI) at admission and determine the relationship between nutritional risk/status and demography/SCI characteristics. China Rehabilitation Research Center, Beijing, China. Baseline clinical data, appetite level, anthropometric measurements and Screening Tool for the Assessment of Malnutrition in Pediatrics (STAMP) scores were obtained for pediatric SCI patients. The relationships among the demographic/SCI characteristics and STAMP score and z-scores of weight-for-age (WAZ), height-for-age (HAZ) and body mass index-for-age (BAZ) were assessed. The risk of undernutrition was compared with actual nutritional status. Forty-five children including 12 boys and 33 girls were included. The risks of undernutrition using the STAMP tool and malnutrition were 51.1% and 55.6%, respectively. Children with different demographic characteristics had similar nutritional status and risk of malnutrition. The risk of undernutrition was associated with nutritional status, including WAZ (P<0.001), HAZ (P=0.001), BAZ (P<0.001) and appetite level (P<0.001). Compared with nutritional status, STAMP had a sensitivity of 100%, a specificity of 73.3% and an overall agreement of 82.2%. As the duration of SCI increased, the risks of overweight and stunting increased. Nutritional screening in all pediatric SCI patients should be performed periodically. The decreasing trends in nutritional status and appetite level after SCI require special attention. The STAMP may be an alternative method for assessing nutritional status in Chinese children with SCI.

Time to pay attention: attentional performance time-stamped prefrontal cholinergic activation, diurnality and performance

PubMed Central

Paolone, Giovanna; Lee, Theresa M.; Sarter, Martin

2012-01-01

Although the impairments in cognitive performance that result from shifting or disrupting daily rhythms have been demonstrated, the neuronal mechanisms that optimize fixed time daily performance are poorly understood. We previously demonstrated that daily practice of a sustained attention task (SAT) evokes a diurnal activity pattern in rats. Here we report that SAT practice at a fixed time produced practice time-stamped increases in prefrontal cholinergic neurotransmission that persisted after SAT practice was terminated and in a different environment. SAT time-stamped cholinergic activation occurred irrespective of whether the SAT was practiced during the light or dark phase or in constant light conditions. In contrast, prior daily practice of an operant schedule of reinforcement, albeit generating more rewards and lever presses per session than the SAT, neither activated the cholinergic system nor affected the animals' nocturnal activity pattern. Likewise, food-restricted animals exhibited strong food anticipatory activity (FAA) and attenuated activity during the dark period but FAA was not associated with increases in prefrontal cholinergic activity. Removal of cholinergic neurons impaired SAT performance and facilitated the reemergence of nocturnality. Shifting SAT practice away from a fixed time resulted in significantly lower performance. In conclusion, these experiments demonstrated that fixed time, daily practice of a task assessing attention generates a precisely practice time-stamped activation of the cortical cholinergic input system. Time-stamped cholinergic activation benefits fixed time performance and, if practiced during the light phase, contributes to a diurnal activity pattern. PMID:22933795

Time to pay attention: attentional performance time-stamped prefrontal cholinergic activation, diurnality, and performance.

PubMed

Paolone, Giovanna; Lee, Theresa M; Sarter, Martin

2012-08-29

Although the impairments in cognitive performance that result from shifting or disrupting daily rhythms have been demonstrated, the neuronal mechanisms that optimize fixed-time daily performance are poorly understood. We previously demonstrated that daily practice of a sustained attention task (SAT) evokes a diurnal activity pattern in rats. Here, we report that SAT practice at a fixed time produced practice time-stamped increases in prefrontal cholinergic neurotransmission that persisted after SAT practice was terminated and in a different environment. SAT time-stamped cholinergic activation occurred regardless of whether the SAT was practiced during the light or dark phase or in constant-light conditions. In contrast, prior daily practice of an operant schedule of reinforcement, albeit generating more rewards and lever presses per session than the SAT, neither activated the cholinergic system nor affected the animals' nocturnal activity pattern. Likewise, food-restricted animals exhibited strong food anticipatory activity (FAA) and attenuated activity during the dark phase but FAA was not associated with increases in prefrontal cholinergic activity. Removal of cholinergic neurons impaired SAT performance and facilitated the reemergence of nocturnality. Shifting SAT practice away from a fixed time resulted in significantly lower performance. In conclusion, these experiments demonstrated that fixed-time, daily practice of a task assessing attention generates a precisely practice time-stamped activation of the cortical cholinergic input system. Time-stamped cholinergic activation benefits fixed-time performance and, if practiced during the light phase, contributes to a diurnal activity pattern.

Study of Theories about Myopia Progression (STAMP) Design and Baseline Data

PubMed Central

Berntsen, David A.; Mutti, Donald O.; Zadnik, Karla

2011-01-01

Purpose The Study of Theories about Myopia Progression (STAMP) is a two-year, double-masked, randomized clinical trial of myopic children 6 to 11 years old. STAMP will evaluate the one-year effect of progressive addition lenses (PALs) compared to single vision lenses (SVLs) on central refraction, peripheral refraction in four quadrants, and accommodative response and convergence. STAMP will also evaluate any changes one year after discontinuing PALs. Baseline characteristics of enrolled children are reported. Methods Eligible children had a high accommodative lag and either: (1) low myopia (less myopic than −2.25 D spherical equivalent) or (2) high myopia (more myopic that −2.25 D spherical equivalent) and esophoria at near. Children were randomly assigned to wear either PALs or SVLs for one year to determine the difference in myopia progression in the PAL group relative to the SVL group. All children will then wear SVLs for the second year to evaluate the permanence of any treatment effect. Complete ocular biometric data are collected at six-month intervals. Results Over 17 months, 192 children were screened, and 85 (44%) were eligible and enrolled. Of these 85 children, 44 (52%) were female, and 54 (64%) were esophoric at near. The mean age (± SD) was 9.8 ± 1.3 years. The right eye mean cycloplegic spherical equivalent refractive error was −1.95 ± 0.78 D. Horizontal relative peripheral hyperopia (30° nasal retina +0.56 ± 0.59 D; 30° temporal retina +0.61 ± 0.77 D) and vertical relative peripheral myopia (30° superior retina −0.36 ± 0.92 D; 20° inferior retina −0.48 ± 0.83 D) were found. Conclusions The baseline data for STAMP are reported. Asymmetry between vertical and horizontal meridian relative peripheral refraction was found. STAMP will utilize the ocular biometric changes associated with the PAL-treatment effect to attempt to elucidate the mechanism responsible for the treatment effect. PMID:20935586

Community response to a sustainable restoration plan for a superfund site.

PubMed

Sidhu, Virinder; Sarkar, Dibyendu; Datta, Rupali; Solomon, Barry

2018-06-01

Large-scale copper (Cu) mining activities in Michigan's Upper Peninsula produced millions of metric tons of mining wastes also known as stamp sands. The stamp sands containing high concentrations of Cu were disposed of into several lakes connected to the Lake Superior. Eventually, as aquatic organisms in these lakes started to exhibit toxicity symptoms, the stamp sands were dredged and discarded on the lake shores. Consequently, these areas turned into degraded, marginal lands and were collectively classified as a Torch Lake Superfund site by the US EPA. Due to the lack of vegetative cover, the Cu-rich stamp sands eroded into the lakes, affecting the aquatic life. To alleviate this issue, a sustainable restoration plan (SRP) was developed and tested in a greenhouse environment prior to field implementation. Cold-tolerant oilseed crops, camelina (Camelina sativa) and field pennycress (Thlaspi arvense), were grown on compost-fertilized stamp sands, which reduced soil erosion by acting as a vegetative cap. Oilseed plants produced normal yield, demonstrating their potential utilization as biofuel feedstock. Prior to implementing the SRP in field-scale in the Torch Lake Superfund site, a public opinion survey of the local community was conducted to understand the views of residents. Door-to-door survey was performed in July-August 2015, which yielded a response rate of 68.1%. Results showed that residents were generally concerned with stamp sand erosion into the Torch Lake and were overwhelmingly supportive of the SRP, which would not only provide environmental benefits but could boost the local economy via biofuel production. To gauge the general environmental awareness of the respondents, the survey included questions on climate change. Most of the respondents acknowledged that climate change is real and anthropogenically mediated. Having college education and a relatively high annual household income showed a positive and significant correlation with climate change awareness.

Block-Module Electric Machines of Alternating Current

NASA Astrophysics Data System (ADS)

Zabora, I.

2018-03-01

The paper deals with electric machines having active zone based on uniform elements. It presents data on disk-type asynchronous electric motors with short-circuited rotors, where active elements are made by integrated technique that forms modular elements. Photolithography, spraying, stamping of windings, pressing of core and combined methods are utilized as the basic technological approaches of production. The constructions and features of operation for new electric machine - compatible electric machines-transformers are considered. Induction motors are intended for operation in hermetic plants with extreme conditions surrounding gas, steam-to-gas and liquid environment at a high temperature (to several hundred of degrees).

Microgravity Induction of TRAIL Expression in Preosteoclast Cells Enhances Osteoclast Differentiation

NASA Astrophysics Data System (ADS)

Sambandam, Yuvaraj; Baird, Kelsey L.; Stroebel, Maxwell; Kowal, Emily; Balasubramanian, Sundaravadivel; Reddy, Sakamuri V.

2016-05-01

Evidence indicates that astronauts experience significant bone loss in space. We previously showed that simulated microgravity (μXg) using the NASA developed rotary cell culture system (RCCS) enhanced bone resorbing osteoclast (OCL) differentiation. However, the mechanism by which μXg increases OCL formation is unclear. RANK/RANKL signaling pathway is critical for OCL differentiation. Tumor necrosis factor-related apoptosis inducing ligand (TRAIL) has been shown to increase osteoclastogenesis. We hypothesize that TRAIL may play an important role in μXg enhanced OCL differentiation. In this study, we identified by RT profiler PCR array screening that μXg induces high levels of TRAIL expression in murine preosteoclast cells in the absence of RANKL stimulation compared to ground based (Xg) cultures. We further identified that μXg elevated the adaptor protein TRAF-6 and fusion genes OC-STAMP and DC-STAMP expression in preosteoclast cells. Interestingly, neutralizing antibody against TRAIL significantly reduced μXg induced OCL formation. We further identified that over-expression of pTRAIL in RAW 264.7 cells enhanced OCL differentiation. These results indicate that TRAIL signaling plays an important role in the μXg increased OCL differentiation. Therefore, inhibition of TRAIL expression could be an effective countermeasure for μXg induced bone loss.

Blockchain protocols in clinical trials: Transparency and traceability of consent.

PubMed

Benchoufi, Mehdi; Porcher, Raphael; Ravaud, Philippe

2017-01-01

Clinical trial consent for protocols and their revisions should be transparent for patients and traceable for stakeholders. Our goal is to implement a process allowing for collection of patients' informed consent, which is bound to protocol revisions, storing and tracking the consent in a secure, unfalsifiable and publicly verifiable way, and enabling the sharing of this information in real time. For that, we build a consent workflow using a trending technology called Blockchain. This is a distributed technology that brings a built-in layer of transparency and traceability. From a more general and prospective point of view, we believe Blockchain technology brings a paradigmatical shift to the entire clinical research field. We designed a Proof-of-Concept protocol consisting of time-stamping each step of the patient's consent collection using Blockchain, thus archiving and historicising the consent through cryptographic validation in a securely unfalsifiable and transparent way. For each protocol revision, consent was sought again.  We obtained a single document, in an open format, that accounted for the whole consent collection process: a time-stamped consent status regarding each version of the protocol. This document cannot be corrupted and can be checked on any dedicated public website. It should be considered a robust proof of data. However, in a live clinical trial, the authentication system should be strengthened to remove the need for third parties, here trial stakeholders, and give participative control to the peer users. In the future, the complex data flow of a clinical trial could be tracked by using Blockchain, which core functionality, named Smart Contract, could help prevent clinical trial events not occurring in the correct chronological order, for example including patients before they consented or analysing case report form data before freezing the database. Globally, Blockchain could help with reliability, security, transparency and could be a consistent step toward reproducibility.

Blockchain protocols in clinical trials: Transparency and traceability of consent

PubMed Central

Benchoufi, Mehdi; Porcher, Raphael; Ravaud, Philippe

2018-01-01

Clinical trial consent for protocols and their revisions should be transparent for patients and traceable for stakeholders. Our goal is to implement a process allowing for collection of patients’ informed consent, which is bound to protocol revisions, storing and tracking the consent in a secure, unfalsifiable and publicly verifiable way, and enabling the sharing of this information in real time. For that, we build a consent workflow using a trending technology called Blockchain. This is a distributed technology that brings a built-in layer of transparency and traceability. From a more general and prospective point of view, we believe Blockchain technology brings a paradigmatical shift to the entire clinical research field. We designed a Proof-of-Concept protocol consisting of time-stamping each step of the patient’s consent collection using Blockchain, thus archiving and historicising the consent through cryptographic validation in a securely unfalsifiable and transparent way. For each protocol revision, consent was sought again.  We obtained a single document, in an open format, that accounted for the whole consent collection process: a time-stamped consent status regarding each version of the protocol. This document cannot be corrupted and can be checked on any dedicated public website. It should be considered a robust proof of data. However, in a live clinical trial, the authentication system should be strengthened to remove the need for third parties, here trial stakeholders, and give participative control to the peer users. In the future, the complex data flow of a clinical trial could be tracked by using Blockchain, which core functionality, named Smart Contract, could help prevent clinical trial events not occurring in the correct chronological order, for example including patients before they consented or analysing case report form data before freezing the database. Globally, Blockchain could help with reliability, security, transparency and could be a consistent step toward reproducibility. PMID:29167732

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jimbert, P.; Fernandez, J. I.; Eguia, I.

It is well known that one of the main advantages of the high speed forming (HSF) processes is the improvement in the forming limits of the used materials.Using the Electromagnetic Forming (EMF) technology two materials have been tested with different mechanical and physical properties: the AA5754 aluminium and the AZ31B magnesium alloys.The EMF process principle can be described as follows: A significant amount of electrical energy is stored in a bank of capacitors which are suddenly discharged releasing all the stored energy. This electric discharge runs through a coil which generates an intense transient magnetic field. At the same timemore » transient Eddy currents are induced in the electrically conductive part placed some millimetres far from the coil. Another intense magnetic field is generated due to those Eddy currents but on the opposite direction as the one generated by the coil. A big magnetic repulsion force is created between the part and the coil. This magnetic repulsion between both fields is used to launch the blank with no physical contact and obtain the desired deformation on it.The Forming Limit Diagrams (FLD) obtained in the EMF experiments were them compared to the ones obtained with the 'Nakazima' method at conventional deformation speed for both alloys. In parallel to these physical experiments, some simulations were carried out. But trying to simulate this process by FEM is a though work. There are several physics and many factors to take into account in a few microseconds deformation process. And all these factors are tightly related with each other, that is why to this date there is no commercial software able to simulate the EMF process accurately.From LABEIN-Tecnalia we are working with to different softwares to simulate the whole process: Maxwell 3D for the electromagnetic part and PAM-STAMP2G for the mechanical part of the problem.« less

Holding fixture for a hot stamping press

NASA Technical Reports Server (NTRS)

Harris, R. P. (Inventor)

1983-01-01

A hand held guide for manually positioning a work piece between the anvil rib and tool of a hot die stamping press is described. A groove completed by interchangeable cover plates attached at one end of the guide conforms to a cross sectional dimension common to similar workpieces and, with a force fit, retentively holds each of the workpieces.

7. VIEW OF HYDRAULIC HAMMER STAMPING PRESS ON SIDE A ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. VIEW OF HYDRAULIC HAMMER STAMPING PRESS ON SIDE A OF BUILDING 883. THIS TYPE OF PRESS WAS USED FOR BOTH STAINLESS STEEL AND FOR DEPLETED URANIUM. (7/2/86) - Rocky Flats Plant, Uranium Rolling & Forming Operations, Southeast section of plant, southeast quadrant of intersection of Central Avenue & Eighth Street, Golden, Jefferson County, CO

25 CFR 310.4 - Application of mark.

Code of Federal Regulations, 2010 CFR

2010-04-01

... be applied to the article with a rubber stamp to be furnished by the Indian Arts and Crafts Board... U S Indian Arts & Crafts Board I D or, in the case of articles too small to carry this stamp: ( ) U... seal disc that shall be impressed and made fast with a hand seal press furnished by the Indian Arts and...

25 CFR 310.7 - Application of mark.

Code of Federal Regulations, 2010 CFR

2010-04-01

... be applied to the article with a rubber stamp to be furnished by the Indian Arts and Crafts Board... U S Indian Arts & Crafts Board I D or, in the case of articles too small to carry this stamp: ( ) U... seal disc that shall be impressed and made fast with a hand seal press furnished by the Indian Arts and...

Falling through the Social Safety Net: Food Stamp Use and Nonuse among Older Impoverished Americans

ERIC Educational Resources Information Center

Fuller-Thomson, Esme; Redmond, Melissa

2008-01-01

Purpose: Older adults are less likely than any other age group to use the federal Food Stamp Program. The personal and social costs of elderly diet insufficiency include disease exacerbation, depression, and increased hospitalization. In order to improve targeting and outreach efforts, this study identifies the characteristics of eligible older…

Development of USPS Laboratory and pilot-scale testing protocols

Treesearch

Carl Houtman; Nancy Ross Sutherland; David Bormett; Donald Donermeyer

2000-01-01

The ultimate goal of the US Postal Service (USPS) Environmentally Benign Stamp Program is to develop stamp adhesives that can be removed by unit operations found in recycling mills. The maintenance of final product quality specifications for a recycling mill while loading the feedstock with a significant quantity of adhesive is the criterion for success of this program...

78 FR 18457 - Definition of Form I-94 To Include Electronic Format

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-27

... parole stamp in a foreign passport to the list of documents designated as evidence of alien registration... will create a Form I-94 in an electronic format based on passenger, passport and visa information DHS... inspection. The officer stamps the Form I-94 and the alien's passport, detaches the bottom portion of the...

Development of Core Competencies for Paraprofessional Nutrition Educators Who Deliver Food Stamp Nutrition Education

ERIC Educational Resources Information Center

Baker, Susan S.; Pearson, Meredith; Chipman, Helen

2009-01-01

The purpose of this project was to describe the process used for the development of core competencies for paraprofessional nutrition educators in Food Stamp Nutrition Education (FSNE). The development process included the efforts of an expert panel of state and multicounty FSNE leaders to draft the core competencies and the validation of those…

The Effect of Food Stamp Nutrition Education on the Food Insecurity of Low-Income Women Participants

ERIC Educational Resources Information Center

Eicher-Miller, Heather A.; Mason, April C.; Abbott, Angela R.; McCabe, George P.; Boushey, Carol J.

2009-01-01

Objective: To determine the effect of Food Stamp Nutrition Education (FSNE) in Indiana on participants' food insecurity and food insufficiency. Design: A single-blind randomized design. A randomized experimental group completed 5 FSNE lessons as an intervention between a pre- and posttest, whereas a control group completed a pre- and posttest…

Watching the Clocks: The Role of Food Stamp Recertification and TANF Time Limits in Caseload Dynamics

ERIC Educational Resources Information Center

Ribar, David C.; Edelhoch, Marilyn; Liu, Qiduan

2008-01-01

We use administrative data to examine how "clock" policies--program time limits and recurring deadlines for confirming eligibility--affected participation in South Carolina's TANF and Food Stamp Programs from 1996-2003. South Carolina's TANF program limits most families to two years of benefits in any ten-year period; so, recipients…