Microbiological performance of a food safety management system in a food service operation.

PubMed

Lahou, E; Jacxsens, L; Daelman, J; Van Landeghem, F; Uyttendaele, M

2012-04-01

The microbiological performance of a food safety management system in a food service operation was measured using a microbiological assessment scheme as a vertical sampling plan throughout the production process, from raw materials to final product. The assessment scheme can give insight into the microbiological contamination and the variability of a production process and pinpoint bottlenecks in the food safety management system. Three production processes were evaluated: a high-risk sandwich production process (involving raw meat preparation), a medium-risk hot meal production process (starting from undercooked raw materials), and a low-risk hot meal production process (reheating in a bag). Microbial quality parameters, hygiene indicators, and relevant pathogens (Listeria monocytogenes, Salmonella, Bacillus cereus, and Escherichia coli O157) were in accordance with legal criteria and/or microbiological guidelines, suggesting that the food safety management system was effective. High levels of total aerobic bacteria (>3.9 log CFU/50 cm(2)) were noted occasionally on gloves of food handlers and on food contact surfaces, especially in high contamination areas (e.g., during handling of raw material, preparation room). Core control activities such as hand hygiene of personnel and cleaning and disinfection (especially in highly contaminated areas) were considered points of attention. The present sampling plan was used to produce an overall microbiological profile (snapshot) to validate the food safety management system in place.

Chemical properties and colors of fermenting materials in salmon fish sauce production.

PubMed

Nakano, Mitsutoshi; Sagane, Yoshimasa; Koizumi, Ryosuke; Nakazawa, Yozo; Yamazaki, Masao; Watanabe, Toshihiro; Takano, Katsumi; Sato, Hiroaki

2018-02-01

This data article reports the chemical properties (moisture, pH, salinity, and soluble solid content) and colors of fermenting materials in salmon fish sauce products. The fish sauce was produced by mixing salt with differing proportions of raw salmon materials and fermenting for three months; the salmon materials comprised flesh, viscera, an inedible portion, and soft roe. Chemical properties and colors of the unrefined fish sauce ( moromi ), and the refined fish sauce, were analyzed at one, two, and three months following the start of fermentation. Data determined for all products are provided in table format.

Roll Compaction/Dry Granulation of Dibasic Calcium Phosphate Anhydrous-Does the Morphology of the Raw Material Influence the Tabletability of Dry Granules?

PubMed

Grote, Simon; Kleinebudde, Peter

2018-04-01

The influence of raw material particle morphology on the tabletabilty of dry granules was investigated. Therefore, dibasic calcium phosphate anhydrous was used as a model material. One milled grade, 2 agglomerated grades with different porosities, and a functionalized structure, that is, an agglomerate formed by very small primary particles, were included. Particle size, density, and specific surface area of raw materials were measured. The starting materials and 2 fractions of dry granules were compressed to tablets. The tabletability of granules was compared to that of the powders and the influence of specific compaction force, granule size, and lubrication on tablet tensile strength was evaluated. All materials showed a loss in tabletability induced by a previous compaction step but to a varying extent. Only in case of the functionalized calcium phosphate morphology, this effect depended on the specific compaction force. In contrast to the other materials, the tabletability of functionalized calcium phosphate was influenced by the granule size. This effect was not related to an overlubrication as internal and external lubrication resulted in similar tensile strengths. A clear influence of the particle morphology on tablet strength was demonstrated by the study. The functionalized structure showed aspects of a more plastic deformation behavior. The functionalized dibasic calcium phosphate and the more porous agglomerate performed as potential filler/binder in the field of roll compaction/dry granulation. Copyright © 2018 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Three-dimensional hierarchical and interconnected honeycomb-like porous carbon derived from pomelo peel for high performance supercapacitors

NASA Astrophysics Data System (ADS)

Liu, Jingyuan; Li, Hongpeng; Zhang, Hongsen; Liu, Qi; Li, Rumin; Li, Bin; Wang, Jun

2018-01-01

The urgent need for sustainable development of human society has forced material scientists to explore novel materials starting from cheap natural precursors for next-generation energy storage devices by using environmentally friendly strategies. In this work, heteroatom-functionalized porous carbonaceous materials with 3D hierarchical and interconnected honeycomb-like structure have been successfully synthesized by using waste biomass pomelo peel as raw material through the combination of hydrothermal carbonization and followed KOH activation procedure. Benefiting from the unique honeycomb-like structure and high specific surface area, the as-obtained carbon material exhibits satisfactory capacitive behavior: 374 F/g at 0.1 A/g; excellent cycling stability of 92.5% capacitance retention over continuous 5000 cycles. More importantly, the as-assembled symmetric supercapacitors based on as-prepared electrode material can deliver high gravimetric and volumetric energy density of 20 W h/kg and 18.7 W h/L in 6 M KOH, respectively, as well as outstanding cycling stability. The obtained results demonstrate the possibility for taking full advantage of sustainable and large scale advanced carbon materials by choosing waste biomass, particularly the pomelo peel as a raw material.

East Europe Report

DTIC Science & Technology

1986-01-17

Sep 85) 82 Polish-USSR Chemical Industry Agreements (RZECZPOSPOLITA, 12 Sep 85) 84 Trade Deals at Mining, Metallurgy Fair (Marian Twarog...RZECZPOSPOLITA, 11 Sep 85) 89 Briefs Stargard-Gdansk Rail Electrification 90 Polish-Libyan Trade Talks 90 ROMANIA New Sources of Raw Material for...approximately 20,000 leaving students will start an apprenticeship in agriculture. Boys and girls have a choice of 18 trades . Effective 1 September

Structural investigation of the cocrystal formed between 5-fluorocytosine and fumaric acid based on vibrational spectroscopic technique

NASA Astrophysics Data System (ADS)

Du, Yong; Cai, Qiang; Xue, Jiadan; Zhang, Qi; Qin, Dan

2017-05-01

The vibrational spectra of 5-fluorocytosine, fumaric acid and their cocrystal were measured using terahertz time-domain spectroscopy (THz-TDS) and Raman spectroscopy at room temperature. Experimental THz results show that the cocrystal has distinct fingerprint spectra in terahertz region. The absorption peaks observed in the terahertz spectra of the cocrystal were at 0.61 and 0.91 THz. These are quite different from corresponding raw starting materials. Raman spectra also show similar results about differences between the cocrystal and corresponding raw starting materials. Density functional theory (DFT) was used to simulate the structure of the possible salt form and the cocrystal form between 5-fluorocytosine and fumaric acid. The theoretical terahertz result shows that the cocrystal form has absorption at 0.62 and 0.87 THz, which is in agreement with the experimental result. The theoretical Raman result also indicates that the cocrystal form has more possibilities than the salt form. So, it is more reasonable that the structure between 5-fluorocytosine and fumaric acid could be the corresponding cocrystal form. The characteristic bands of the cocrystal between 5-fluorocytosine and fumaric acid are also assigned based on the simulation results from the DFT calculation.

Efficient degradation of lignin in raw wood via pretreatment with heteropoly acids in γ-valerolactone/water.

PubMed

Zhang, Libo; Zheng, Wenxiu; Wang, Ziming; Ma, Yubo; Jiang, Ling; Wang, Tianfu

2018-08-01

The aim of this work was to study the degradation of lignin in raw wood via pretreatment with heteropoly acids as substitutes for traditional H 2 SO 4 in γ-valerolactone/water. By optimizing catalyst concentration, reaction time and temperature, the optimal lignin degradation conditions are obtained (130 °C, 3 h and 20 mM silicotungstic acid). SEM and FTIR measurements demonstrated the efficient lignin degradation ability of HPAs in the GVL/H 2 O solvent, with negligible damage to cellulose within the raw wood. Furthermore, an elaborated enzymatic hydrolysis study of the thus obtained cellulosic feedstock revealed its suitability for enzymatic digestion, with great potential as starting material for the production of fermentable sugar from biomass in future biorefinery applications. Copyright © 2018 Elsevier Ltd. All rights reserved.

Bacterial community structure transformed after thermophilically composting human waste in Haiti

PubMed Central

Kramer, Sasha; Roy, Monika; Reid, Francine C.; Dubinsky, Eric A.

2017-01-01

Recycling human waste for beneficial use has been practiced for millennia. Aerobic (thermophilic) composting of sewage sludge has been shown to reduce populations of opportunistically pathogenic bacteria and to inactivate both Ascaris eggs and culturable Escherichia coli in raw waste, but there is still a question about the fate of most fecal bacteria when raw material is composted directly. This study undertook a comprehensive microbial community analysis of composting material at various stages collected over 6 months at two composting facilities in Haiti. The fecal microbiota signal was monitored using a high-density DNA microarray (PhyloChip). Thermophilic composting altered the bacterial community structure of the starting material. Typical fecal bacteria classified in the following groups were present in at least half the starting material samples, yet were reduced below detection in finished compost: Prevotella and Erysipelotrichaceae (100% reduction of initial presence), Ruminococcaceae (98–99%), Lachnospiraceae (83–94%, primarily unclassified taxa remained), Escherichia and Shigella (100%). Opportunistic pathogens were reduced below the level of detection in the final product with the exception of Clostridium tetani, which could have survived in a spore state or been reintroduced late in the outdoor maturation process. Conversely, thermotolerant or thermophilic Actinomycetes and Firmicutes (e.g., Thermobifida, Bacillus, Geobacillus) typically found in compost increased substantially during the thermophilic stage. This community DNA-based assessment of the fate of human fecal microbiota during thermophilic composting will help optimize this process as a sanitation solution in areas where infrastructure and resources are limited. PMID:28570610

System simulation application for determining the size of daily raw material purchases at PT XY

NASA Astrophysics Data System (ADS)

Napitupulu, H. L.

2018-02-01

Every manufacturing company needs to implement green production, including PT XY as a marine catchment processing industry in Sumatera Utara Province. The company is engaged in the processing of squid for export purposes. The company’s problem relates to the absence of a decision on the daily purchase amount of the squid. The purchase of daily raw materials in varying quantities has caused companies to face the problem of excess raw materials or otherwise the lack of raw materials. The low purchase of raw materials will result in reduced productivity, while large purchases will lead to increased cooling costs for storage of excess raw materials, as well as possible loss of damage raw material. Therefore it is necessary to determine the optimal amount of raw material purchases every day. This can be determined by applying simulation. Application of system simulations can provide the expected optimal amount of raw material purchases.

Electrochemical device for syngas and liquid fuels production

DOEpatents

Braun, Robert J.; Becker, William L.; Penev, Michael

2017-04-25

The invention relates to methods for creating high value liquid fuels such as gasoline, diesel, jet and alcohols using carbon dioxide and water as the starting raw materials and a system for using the same. These methods combine a novel solid oxide electrolytic cell (SOEC) for the efficient and clean conversion of carbon dioxide and water to hydrogen and carbon monoxide, uniquely integrated with a gas-to-liquid fuels producing method.

USSR Report, Energy, No. 152.

DTIC Science & Technology

1983-06-17

384,000 cubic meters of mineral wool are shipped annually. Five thousand freight cars are needed for their shipment. However, the organization of the...production of such a quantity of mineral wool directly at the places of consumption from imported starting raw material with the use of local type...manufacturers often simply make the appearance of a package. How else can one speak of packaging of mineral wool in wrapping paper. This thermal

Structural investigation of the cocrystal formed between 5-fluorocytosine and fumaric acid based on vibrational spectroscopic technique.

PubMed

Du, Yong; Cai, Qiang; Xue, Jiadan; Zhang, Qi; Qin, Dan

2017-05-05

The vibrational spectra of 5-fluorocytosine, fumaric acid and their cocrystal were measured using terahertz time-domain spectroscopy (THz-TDS) and Raman spectroscopy at room temperature. Experimental THz results show that the cocrystal has distinct fingerprint spectra in terahertz region. The absorption peaks observed in the terahertz spectra of the cocrystal were at 0.61 and 0.91THz. These are quite different from corresponding raw starting materials. Raman spectra also show similar results about differences between the cocrystal and corresponding raw starting materials. Density functional theory (DFT) was used to simulate the structure of the possible salt form and the cocrystal form between 5-fluorocytosine and fumaric acid. The theoretical terahertz result shows that the cocrystal form has absorption at 0.62 and 0.87THz, which is in agreement with the experimental result. The theoretical Raman result also indicates that the cocrystal form has more possibilities than the salt form. So, it is more reasonable that the structure between 5-fluorocytosine and fumaric acid could be the corresponding cocrystal form. The characteristic bands of the cocrystal between 5-fluorocytosine and fumaric acid are also assigned based on the simulation results from the DFT calculation. Copyright © 2017 Elsevier B.V. All rights reserved.

40 CFR 63.1348 - Standards for affected sources other than kilns; in-line kiln/raw mills; clinker coolers; new and...

Code of Federal Regulations, 2010 CFR

2010-07-01

... than kilns; in-line kiln/raw mills; clinker coolers; new and reconstructed raw material dryers; and raw...; in-line kiln/raw mills; clinker coolers; new and reconstructed raw material dryers; and raw and finish mills. The owner or operator of each new or existing raw material, clinker, or finished product...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yalcin, M.; Arol, A.I.

Coconut shells are the most widely used raw material for the production of activated carbon used in the gold production by cyanide leaching. There have been efforts to find alternatives to coconut shells. Shells and stones of certain fruits, have been tested. Although promising results to some extent were obtained, coconut shells remain the main source of activated carbon. Turkey has become a country of interest in terms of gold deposits of epithermal origin. Four deposits have already been discovered and, mining and milling operations are expected to start in the near future. Explorations are underway in many other areasmore » of high expectations. Turkey is also rich in fruits which can be a valuable source of raw material for activated carbon production. In this study, hazelnut shells, peach and apricot stones, abundantly available locally, have been tested to determine whether they are suitable for the gold metallurgy. Parameters of carbonization and activation have been optimized. Gold loading capacity and adsorption kinetics have been studied.« less

Effects of limestone petrography and calcite microstructure on OPC clinker raw meals burnability

NASA Astrophysics Data System (ADS)

Galimberti, Matteo; Marinoni, Nicoletta; Della Porta, Giovanna; Marchi, Maurizio; Dapiaggi, Monica

2017-10-01

Limestone represents the main raw material for ordinary Portland cement clinker production. In this study eight natural limestones from different geological environments were chosen to prepare raw meals for clinker manufacturing, aiming to define a parameter controlling the burnability. First, limestones were characterized by X-Ray Fluorescence, X-Ray Powder Diffraction and Optical Microscopy to assess their suitability for clinker production and their petrographic features. The average domains size and the microstrain of calcite were also determined by X-Ray Powder Diffraction line profile analysis. Then, each limestone was admixed with clay minerals to achieve the adequate chemical composition for clinker production. Raw meals were thermally threated at seven different temperatures, from 1000 to 1450 °C, to evaluate their behaviour on heating by ex situ X-Ray Powder Diffraction and to observe the final clinker morphology by Scanning Electron Microscopy. Results indicate the calcite microstrain is a reliable parameter to predict the burnability of the raw meals, in terms of calcium silicates growth and lime consumption. In particular, mixtures prepared starting from high-strained calcite exhibit a better burnability. Later, when the melt appears this correlation vanishes; however differences in the early burnability still reflect on the final clinker composition and texture.

31 CFR 560.407 - Transactions related to Iranian-origin goods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... from third countries of goods containing Iranian-origin raw materials or components is not prohibited if those raw materials or components have been incorporated into manufactured products or... Iranian-origin raw materials or components are not prohibited if those raw materials or components have...

Shipboard Aggregate Power Monitoring

DTIC Science & Technology

2009-06-01

low pressure air serves to operate various valves and provide pneumatic power for certain plant equipment. The compressor is an Ingersoll-Rand NAXI...List of Figures Figure 1-1: Raw AC voltage and current measurements for recorded during a motor start-up. (1...filters, valves, etc.) of a given system. Figure 1-1: Raw AC voltage and current measurements recorded during a motor start-up. (1) Figure

31 CFR 560.407 - Transactions related to Iranian-origin goods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... United States from third countries of goods containing Iranian-origin raw materials or components is not prohibited if those raw materials or components have been incorporated into manufactured products or... Iranian-origin raw materials or components are not prohibited if those raw materials or components have...

Environmentally-Friendly Geopolymeric Binders Made with Silica

NASA Astrophysics Data System (ADS)

Erdogan, S. T.

2013-12-01

Portland cement (PC) is the ubiquitous binding material for constructions works. It is a big contributor to global warming and climate change since its production is responsible for 5-10 % of all anthropogenic CO2 emissions. Half of this emission arises from the calcination of calcareous raw materials and half from kiln fuel burning and cement clinker grinding. Recently there have been efforts to develop alternative binders with lower greenhouse gas emissions. One such class of binders is geopolymers, formed by activating natural or waste materials with suitable alkaline or acidic solutions. These binders use natural or industrial waste raw materials with a very low CO2 footprint from grinding of the starting materials, and some from the production of the activating chemicals. The total CO2 emissions from carefully formulated mixtures can be as low as 1/10th - 1/5th of those of PC concrete mixtures with comparable properties. While use of industrial wastes as raw materials is environmentally preferable, the variability of their chemical compositions over time renders their use difficult. Use of natural materials depletes resources but can have more consistent properties and can be more easily accepted. Silica sand is a natural material containing very high amounts of quartz. Silica fume is a very fine waste from silicon metal production that is mostly non-crystalline silica. This study describes the use of sodium hydroxide and sodium silicate solutions to yield mortars with mechanical properties comparable to those of portland cement mortars and with better chemical and thermal durability. Strength gain is slower than with PC mixtures at room temperature but adequate ultimate strength can be achieved with curing at slightly elevated temperatures in less than 24 h. The consistency of the chemical compositions of these materials and their abundance in several large, developing countries makes silica attractive for producing sustainable concretes with reduced carbon footprints.

Ceramic Processing

DOE Office of Scientific and Technical Information (OSTI.GOV)

EWSUK,KEVIN G.

1999-11-24

Ceramics represent a unique class of materials that are distinguished from common metals and plastics by their: (1) high hardness, stiffness, and good wear properties (i.e., abrasion resistance); (2) ability to withstand high temperatures (i.e., refractoriness); (3) chemical durability; and (4) electrical properties that allow them to be electrical insulators, semiconductors, or ionic conductors. Ceramics can be broken down into two general categories, traditional and advanced ceramics. Traditional ceramics include common household products such as clay pots, tiles, pipe, and bricks, porcelain china, sinks, and electrical insulators, and thermally insulating refractory bricks for ovens and fireplaces. Advanced ceramics, also referredmore » to as ''high-tech'' ceramics, include products such as spark plug bodies, piston rings, catalyst supports, and water pump seals for automobiles, thermally insulating tiles for the space shuttle, sodium vapor lamp tubes in streetlights, and the capacitors, resistors, transducers, and varistors in the solid-state electronics we use daily. The major differences between traditional and advanced ceramics are in the processing tolerances and cost. Traditional ceramics are manufactured with inexpensive raw materials, are relatively tolerant of minor process deviations, and are relatively inexpensive. Advanced ceramics are typically made with more refined raw materials and processing to optimize a given property or combination of properties (e.g., mechanical, electrical, dielectric, optical, thermal, physical, and/or magnetic) for a given application. Advanced ceramics generally have improved performance and reliability over traditional ceramics, but are typically more expensive. Additionally, advanced ceramics are typically more sensitive to the chemical and physical defects present in the starting raw materials, or those that are introduced during manufacturing.« less

Effect of the raw material type and the reaction time on the synthesis of halloysite based Zeolite Na-P1

NASA Astrophysics Data System (ADS)

Meftah, Mahdi; Oueslati, Walid; Chorfi, Nejmeddine; Ben Haj Amara, Abdesslem

Zeolites are currently one of the most important classes of inorganic materials because of their multiple applications not only as ions exchangers and molecular sieves, but also as catalysts. This works focus the synthesis and the characterization of Zeolite Na-P1 using halloysite (collected near Ain Khemouda, western Tunisia) as the starting material. Two parameters, such as the host materials type (natural or treated) and the reaction time, involved in the synthesis process are investigated. The intermediate phases and final products were characterized by X-ray diffraction, Infrared IR spectroscopy, scanning electron microscopy and high-resolution 29Si and 27Al MAS NMR. Obtained results show that the hydrothermal synthesis from natural and heated-halloysite leads to formation of homogenous Zeolite Na-P1. The difference in the crystallization/transformation time process is explained by the effect of the dissolution rate of the starting materials in sodium hydroxide solution. In the case of heated halloysite, the synthesis reaction with alkali solution occurs very readily and achieved without prior thermal activation at high temperature. The optimal conditions of Zeolite Na-P1 crystallization, from heated-halloysite, are reached at 120 °C.

Measurement Challenges for Carbon Nanotube Material

NASA Technical Reports Server (NTRS)

Sosa, Edward; Arepalli, Sivaram; Nikolaev, Pasha; Gorelik, Olga; Yowell, Leonard

2006-01-01

The advances in large scale applications of carbon nanotubes demand a reliable supply of raw and processed materials. It is imperative to have a consistent quality control of these nanomaterials to distinguish material inconsistency from the modifications induced by processing of nanotubes for any application. NASA Johnson Space Center realized this need five years back and started a program to standardize the characterization methods. The JSC team conducted two workshops (2003 and 2005) in collaboration with NIST focusing on purity and dispersion measurement issues of carbon nanotubes [1]. In 2004, the NASA-JSC protocol was developed by combining analytical techniques of SEM, TEM, UV-VIS-NIR absorption, Raman, and TGA [2]. This protocol is routinely used by several researchers across the world as a first step in characterizing raw and purified carbon nanotubes. A suggested practice guide consisting of detailed chapters on TGA, Raman, electron microscopy and NIR absorption is in the final stages and is undergoing revisions with input from the nanotube community [3]. The possible addition of other techniques such as XPS, and ICP to the existing protocol will be presented. Recent activities at ANSI and ISO towards implementing these protocols as nanotube characterization standards will be discussed.

40 CFR 63.1343 - What standards apply to my kilns, clinker coolers, raw material dryers, and open clinker piles?

Code of Federal Regulations, 2011 CFR

2011-07-01

..., clinker coolers, raw material dryers, and open clinker piles? 63.1343 Section 63.1343 Protection of... What standards apply to my kilns, clinker coolers, raw material dryers, and open clinker piles? (a..., clinker cooler, and raw material dryer. All dioxin D/F, HCl, and total hydrocarbon (THC) emission limits...

26 CFR 1.472-1 - Last-in, first-out inventories.

Code of Federal Regulations, 2011 CFR

2011-04-01

... may elect to have such method apply to the raw materials only (including those included in goods in... adjustments are confined to costs of the raw material in the inventory and the cost of the raw material in... that the opening inventory had 10 units of raw material, 10 units of goods in process, and 10 units of...

40 CFR 63.1343 - What standards apply to my kilns, clinker coolers, raw material dryers, and open clinker storage...

Code of Federal Regulations, 2014 CFR

2014-07-01

..., clinker coolers, raw material dryers, and open clinker storage piles? 63.1343 Section 63.1343 Protection... Limits § 63.1343 What standards apply to my kilns, clinker coolers, raw material dryers, and open clinker... associated with that kiln, clinker cooler, raw material dryer, and open clinker storage pile. All D/F, HCl...

40 CFR 63.1343 - What standards apply to my kilns, clinker coolers, raw material dryers, and open clinker storage...

Code of Federal Regulations, 2013 CFR

2013-07-01

..., clinker coolers, raw material dryers, and open clinker storage piles? 63.1343 Section 63.1343 Protection... Limits § 63.1343 What standards apply to my kilns, clinker coolers, raw material dryers, and open clinker... associated with that kiln, clinker cooler, raw material dryer, and open clinker storage pile. All D/F, HCl...

40 CFR 63.1343 - What standards apply to my kilns, clinker coolers, raw material dryers, and open clinker piles?

Code of Federal Regulations, 2012 CFR

2012-07-01

..., clinker coolers, raw material dryers, and open clinker piles? 63.1343 Section 63.1343 Protection of... What standards apply to my kilns, clinker coolers, raw material dryers, and open clinker piles? (a..., clinker cooler, and raw material dryer. All dioxin D/F, HCl, and total hydrocarbon (THC) emission limits...

26 CFR 1.472-1 - Last-in, first-out inventories.

Code of Federal Regulations, 2014 CFR

2014-04-01

... may elect to have such method apply to the raw materials only (including those included in goods in... adjustments are confined to costs of the raw material in the inventory and the cost of the raw material in... that the opening inventory had 10 units of raw material, 10 units of goods in process, and 10 units of...

26 CFR 1.472-1 - Last-in, first-out inventories.

Code of Federal Regulations, 2013 CFR

2013-04-01

... may elect to have such method apply to the raw materials only (including those included in goods in... adjustments are confined to costs of the raw material in the inventory and the cost of the raw material in... that the opening inventory had 10 units of raw material, 10 units of goods in process, and 10 units of...

26 CFR 1.472-1 - Last-in, first-out inventories.

Code of Federal Regulations, 2012 CFR

2012-04-01

... may elect to have such method apply to the raw materials only (including those included in goods in... adjustments are confined to costs of the raw material in the inventory and the cost of the raw material in... that the opening inventory had 10 units of raw material, 10 units of goods in process, and 10 units of...

[Which one is more important, raw materials or productive technology?--a case study for quality consistency control of Gegen Qinlian decoction].

PubMed

Zhong, Wen; Chen, Sha; Zhang, Jun; Wang, Yu-Sheng; Liu, An

2016-03-01

To investigate the effect of Chinese medicine raw materials and production technology on quality consistency of Chinese patent medicines with Gegen Qinlian decoction as an example, and establish a suitable method for the quality consistency control of Chinese patent medicines. The results showed that the effect of production technology on the quality consistency was generally not more than 5%, while the effect of raw materials was even more than 30%, indicating that the effect of raw materials was much greater than that of the production technology. In this study, blend technology was used to improve the quality consistency of raw materials. As a result, the difference between the product produced by raw materials and reference groups was less than 5%, thus increasing the quality consistence of finished products. The results showed that under the current circumstances, the main factor affecting the quality consistency of Chinese patent medicines was raw materials, so we shall pay more attention to the quality of Chinese medicine's raw materials. Finally, a blend technology can improve the quality consistency of Chinese patent medicines. Copyright© by the Chinese Pharmaceutical Association.

21 CFR 1304.31 - Reports from manufacturers importing narcotic raw material.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Reports from manufacturers importing narcotic raw... RECORDS AND REPORTS OF REGISTRANTS Reports § 1304.31 Reports from manufacturers importing narcotic raw material. (a) Every manufacturer which imports or manufactures from narcotic raw material (opium, poppy...

21 CFR 1304.31 - Reports from manufacturers importing narcotic raw material.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 9 2011-04-01 2011-04-01 false Reports from manufacturers importing narcotic raw... RECORDS AND REPORTS OF REGISTRANTS Reports § 1304.31 Reports from manufacturers importing narcotic raw material. (a) Every manufacturer which imports or manufactures from narcotic raw material (opium, poppy...

29 CFR 779.333 - Goods sold for use as raw materials in other products.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 29 Labor 3 2011-07-01 2011-07-01 false Goods sold for use as raw materials in other products. 779... Service Establishments Sales Not Made for Resale § 779.333 Goods sold for use as raw materials in other products. Goods are sold for resale where they are sold for use as a raw material in the production of a...

29 CFR 779.333 - Goods sold for use as raw materials in other products.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 3 2010-07-01 2010-07-01 false Goods sold for use as raw materials in other products. 779... Service Establishments Sales Not Made for Resale § 779.333 Goods sold for use as raw materials in other products. Goods are sold for resale where they are sold for use as a raw material in the production of a...

40 CFR Table N-1 to Subpart N of... - CO2 Emission Factors for Carbonate-Based Raw Materials

Code of Federal Regulations, 2011 CFR

2011-07-01

...-Based Raw Materials N Table N-1 to Subpart N of Part 98 Protection of Environment ENVIRONMENTAL... Raw Materials Carbonate-basedraw material—mineral CO2 emission factor a Limestone—CaCO3 0.440 Dolomite... in units of metric tons of CO2 emitted per metric ton of carbonate-based raw material charged to the...

40 CFR 63.1346 - Standards for new or reconstructed raw material dryers.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 11 2010-07-01 2010-07-01 true Standards for new or reconstructed raw... Industry Emission Standards and Operating Limits § 63.1346 Standards for new or reconstructed raw material dryers. (a) New or reconstructed raw material dryers located at facilities that are major sources can not...

Extraterrestrial materials processing

NASA Technical Reports Server (NTRS)

Steurer, W. H.

1982-01-01

The first year results of a multi-year study of processing extraterrestrial materials for use in space are summarized. Theoretically, there are potential major advantages to be derived from the use of such materials for future space endeavors. The types of known or postulated starting raw materials are described including silicate-rich mixed oxides on the Moon, some asteroids and Mars; free metals in some asteroids and in small quantities in the lunar soil; and probably volatiles like water and CO2 on Mars and some asteroids. Candidate processes for space materials are likely to be significantly different from their terrestrial counterparts largely because of: absence of atmosphere; lack of of readily available working fluids; low- or micro-gravity; no carbon-based fuels; readily available solar energy; and severe constraints on manned intervention. The extraction of metals and oxygen from lunar material by magma electrolysis or by vapor/ion phase separation appears practical.

Scoping Future Policy Dynamics in Raw Materials Through Scenarios Testing

NASA Astrophysics Data System (ADS)

Correia, Vitor; Keane, Christopher; Sturm, Flavius; Schimpf, Sven; Bodo, Balazs

2017-04-01

The International Raw Materials Observatory (INTRAW) project is working towards a sustainable future for the European Union in access to raw materials, from an availability, economical, and environmental framework. One of the major exercises for the INTRAW project is the evaluation of potential future scenarios for 2050 to frame economic, research, and environmental policy towards a sustainable raw materials supply. The INTRAW consortium developed three possible future scenarios that encompass defined regimes of political, economic, and technological norms. The first scenario, "Unlimited Trade," reflects a world in which free trade continues to dominate the global political and economic environment, with expectations of a growing demand for raw materials from widely distributed global growth. The "National Walls" scenario reflects a world where nationalism and economic protectionism begins to dominate, leading to stagnating economic growth and uneven dynamics in raw materials supply and demand. The final scenario, "Sustainability Alliance," examines the dynamics of a global political and economic climate that is focused on environmental and economic sustainability, leading towards increasingly towards a circular raw materials economy. These scenarios were reviewed, tested, and provided simulations of impacts with members of the Consortium and a panel of global experts on international raw materials issues which led to expected end conditions for 2050. Given the current uncertainty in global politics, these scenarios are informative to identifying likely opportunities and crises. The details of these simulations and expected responses to the research demand, technology investments, and economic components of raw materials system will be discussed.

Ground test article for deployable space structure systems

NASA Technical Reports Server (NTRS)

Malloy, G. D.

1984-01-01

The ground test article fabrication and assembly plan was completed by Santek Engineering, Inc. The plan was reviewed and accepted by Rockwell during an on-site visit to the Santek facility. Raw material and hardware orders were placed by Santek in July. Approximately 98% of the raw materials and 10% of the hardware deliveries have been completed. Several material and hardware substitutions were requested by Santek due to no-bid responses from suppliers or excessive costs for limited quantity items. These substitutions were evaluated and approved by Rockwell Engineering and Material and Process and are being incorporated into the drawing package. Santek started fabrication of detail parts in mid-August. Their current resource utilization is at approximately 50% of the planned eventual commitment and is increasing at a rate commensurate with the fabrication and assembly plan. At this writing, Santek's estimate of completion is 03%. During verification testing of the diagonal member joint, in a program funded by Rockwell discretionary funds, the axial load to unlock the joint was found to increase significantly after a few cycles of operation. This was attributed to galling, poor lubrication, and locking pin geometry. A change of materials, lubricant, and modification of the pin geometry reduced the unlocking load and provided repeatability after 50 cycles of operation. This new design is being implemented into the ground test article.

40 CFR 428.75 - Standards of performance for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.26 0.093 TSS 0.50 0.25 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.26 0...— Metric units (kg/kkg of raw material) Lead 0.0017 0.0007 English units (lb/1,000 lb of raw material) Lead...

40 CFR 428.75 - Standards of performance for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.26 0.093 TSS 0.50 0.25 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.26 0...— Metric units (kg/kkg of raw material) Lead 0.0017 0.0007 English units (lb/1,000 lb of raw material) Lead...

Study on optimum length of raw material in stainless steel high-lock nuts forging

NASA Astrophysics Data System (ADS)

Cheng, Meiwen; Liu, Fenglei; Zhao, Qingyun; Wang, Lidong

2018-04-01

Taking 302 stainless steel (1Cr18Ni9) high-lock nuts for research objects, adjusting the length of raw material, then using DEFORM software to simulate the isothermal forging process of each station and conducting the corresponding field tests to study the effects of raw material size on the stainless steel high-lock nuts forming performance. The tests show that the samples of each raw material length is basically the same as the results of the DEFORM software. When the length of the raw material is 10mm, the appearance size of the parts can meet the design requirements.

40 CFR 428.55 - Standards of performance for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.70 0.25 TSS 1.28 0.64 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.70 0.25...— Metric units (kg/kkg of raw material) Lead 0.0017 0.0007 English units (lb/1,000 lb of raw material) Lead...

40 CFR 428.55 - Standards of performance for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.70 0.25 TSS 1.28 0.64 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.70 0.25...— Metric units (kg/kkg of raw material) Lead 0.0017 0.0007 English units (lb/1,000 lb of raw material) Lead...

40 CFR 428.65 - Standards of performance for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.42 0.15 TSS 0.80 0.40 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.42 0.0...— Metric units (kg/kkg of raw material) Lead 0.0017 0.0007 English units (lb/1,000 lb of raw material) Lead...

40 CFR 428.65 - Standards of performance for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.42 0.15 TSS 0.80 0.40 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.42 0.0...— Metric units (kg/kkg of raw material) Lead 0.0017 0.0007 English units (lb/1,000 lb of raw material) Lead...

INTRAW, the EU Observatory for raw materials: fostering international cooperation and developing new opportunities

NASA Astrophysics Data System (ADS)

Correia, Victor; Allington, Ruth; Keane, Christopher

2016-04-01

A secure supply of raw materials is a European priority that extends beyond country borders and national policies. Recent European initiatives have pioneered the development of an EU strategy on raw materials emphasizing the concept of the "added value chain", which continues to pursue the three pillar strategy to: (1) ensure the fair and sustainable supply of raw materials from international markets, promoting international cooperation with developed and developing countries; (2) foster sustainable supply of raw materials from European sources, and (3) reduce consumption of primary raw materials by increasing resource efficiency and promoting recycling. This contribution presents the Horizon 2020 funded project INTRAW, the objective of which is to establish the European Union's International Observatory for Raw Materials. The creation and maintenance of the European Union's International Observatory for Raw Materials is designed to have a strong impact in two dimensions: 1. To narrow the existing gap in aspects of the raw materials knowledge infrastructure in the EU by providing a link with the same knowledge infrastructure in technologically advanced reference countries. This should contribute to the harmonization of mineral policies all over the EU, by providing data that enables evidence-based policies and appropriate, cost-effective management, planning and adaptation decisions by the public sector. This will benefit businesses, industry and society. The Observatory will also provide to policy makers in the EU and its Member States the data they need to facilitate discussion in multilateral forums. 2. To enable a better alignment of the R&I activities among the individual EU members and international cooperation countries AND between the European Union and international cooperation countries by boosting synergies with international research and innovation programmes. This way the EU's role and scientific capabilities in the raw materials area will be reinforced in the mid-term, and the conditions for sustainable access and supply of raw materials in the EU will benefit from the international cooperation. The authors will describe the key stages of the INTRAW project and explain how it aims to establish (and promote the continuation of) international cooperation at every stage of the raw materials value chain and to build a repository of information and analysis to support the development and strengthening of EU raw materials strategies. Key elements of the value chain upon which the project focuses are: industry and trade; education and outreach; and research and innovation. The roles of geoscientists in delivering the aims and objectives of INTRAW will be emphasised.

Methodology for Evaluating Raw Material Changes to RSRM Elastomeric Insulation Materials

NASA Technical Reports Server (NTRS)

Mildenhall, Scott D.; McCool, Alex (Technical Monitor)

2001-01-01

The Reusable Solid Rocket Motor (RSRM) uses asbestos and silicon dioxide filled acrylonitrile butadiene rubber (AS-NBR) as the primary internal insulation to protect the case from heat. During the course of the RSRM Program, several changes have been made to the raw materials and processing of the AS-NBR elastomeric insulation material. These changes have been primarily caused by raw materials becoming obsolete. In addition, some process changes have been implemented that were deemed necessary to improve the quality and consistency of the AS-NBR insulation material. Each change has been evaluated using unique test efforts customized to determine the potential impacts of the specific raw material or process change. Following the evaluations, the various raw material and process changes were successfully implemented with no detectable effect on the performance of the AS-NBR insulation. This paper will discuss some of the raw material and process changes evaluated, the methodology used in designing the unique test plans, and the general evaluation results. A summary of the change history of RSRM AS-NBR internal insulation is also presented.

Process to create simulated lunar agglutinate particles

NASA Technical Reports Server (NTRS)

Gustafson, Robert J. (Inventor); Gustafson, Marty A. (Inventor); White, Brant C. (Inventor)

2011-01-01

A method of creating simulated agglutinate particles by applying a heat source sufficient to partially melt a raw material is provided. The raw material is preferably any lunar soil simulant, crushed mineral, mixture of crushed minerals, or similar material, and the heat source creates localized heating of the raw material.

Solving a layout design problem by analytic hierarchy process (AHP) and data envelopment analysis (DEA) approach

NASA Astrophysics Data System (ADS)

Tuzkaya, Umut R.; Eser, Arzum; Argon, Goner

2004-02-01

Today, growing amounts of waste due to fast consumption rate of products started an irreversible environmental pollution and damage. A considerable part of this waste is caused by packaging material. With the realization of this fact, various waste policies have taken important steps. Here we considered a firm, where waste Aluminum constitutes majority of raw materials for this fir0m. In order to achieve a profitable recycling process, plant layout should be well designed. In this study, we propose a two-step approach involving Analytic Hierarchy Process (AHP) and Data Envelopment Analysis (DEA) to solve facility layout design problems. A case example is considered to demonstrate the results achieved.

Profitability and sustainability of small - medium scale palm biodiesel plant

NASA Astrophysics Data System (ADS)

Solikhah, Maharani Dewi; Kismanto, Agus; Raksodewanto, Agus; Peryoga, Yoga

2017-06-01

The mandatory of biodiesel application at 20% blending (B20) has been started since January 2016. It creates huge market for biodiesel industry. To build large-scale biodiesel plant (> 100,000 tons/year) is most favorable for biodiesel producers since it can give lower production cost. This cost becomes a challenge for small - medium scale biodiesel plants. However, current biodiesel plants in Indonesia are located mainly in Java and Sumatra, which then distribute biodiesel around Indonesia so that there is an additional cost for transportation from area to area. This factor becomes an opportunity for the small - medium scale biodiesel plants to compete with the large one. This paper discusses the profitability of small - medium scale biodiesel plants conducted on a capacity of 50 tons/day using CPO and its derivatives. The study was conducted by performing economic analysis between scenarios of biodiesel plant that using raw material of stearin, PFAD, and multi feedstock. Comparison on the feasibility of scenarios was also conducted on the effect of transportation cost and selling price. The economic assessment shows that profitability is highly affected by raw material price so that it is important to secure the source of raw materials and consider a multi-feedstock type for small - medium scale biodiesel plants to become a sustainable plant. It was concluded that the small - medium scale biodiesel plants will be profitable and sustainable if they are connected to palm oil mill, have a captive market, and are located minimally 200 km from other biodiesel plants. The use of multi feedstock could increase IRR from 18.68 % to 56.52 %.

Improved silicon nitride for advanced heat engines

NASA Technical Reports Server (NTRS)

Yeh, H. C.; Wimmer, J. M.

1986-01-01

Silicon nitride is a high temperature material currently under consideration for heat engine and other applications. The objective is to improve the net shape fabrication technology of Si3N4 by injection molding. This is to be accomplished by optimizing the process through a series of statistically designed matrix experiments. To provide input to the matrix experiments, a wide range of alternate materials and processing parameters was investigated throughout the whole program. The improvement in the processing is to be demonstrated by a 20 percent increase in strength and a 100 percent increase in the Weibull modulus over that of the baseline material. A full characterization of the baseline process was completed. Material properties were found to be highly dependent on each step of the process. Several important parameters identified thus far are the starting raw materials, sinter/hot isostatic pressing cycle, powder bed, mixing methods, and sintering aid levels.

40 CFR 428.72 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.26 0.093 TSS 0.50 0.25 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.26 0.../kkg of raw material) Lead 0.0017 0.0007 English units (lb/1,000 lb of raw material) Lead 0.0017 0.0007...

40 CFR 428.52 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.70 0.25 TSS 1.28 0.64 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.70 0.25... of raw material) Lead 0.0017 0.0007 English units (lb/1,000 lb of raw material) Lead 0.0017 0.0007 (c...

VERAM - Vision and Roadmap for European Raw Materials

NASA Astrophysics Data System (ADS)

Baumgarten, Wibke; Vashev, Boris

2017-04-01

The overall objective of VERAM project is to produce a Vision and Roadmap for European Raw Materials in 2050 based on raw materials research and innovation (R&I) coordination. Two leading European Technology Platforms (ETPs): ETP SMR (Sustainable Minerals Resources) and FTP (Forest Technology Platform) are joining forces to develop a common vison and roadmap with the support of ECTP (European Construction Technology Platform), represented by UNIVPM, SusChem (ETP for Sustainable Chemistry), represented by Cefic, EuMaT (Advanced Materials ETP), represented by VITO, ERAMIN 2, represented by Research Centre JUELICH and WoodWisdom Network Plus represented by the Agency for Renewable Resources (FNR). This partnership provides VERAM with expertise from downstream applications and additional knowledge on non-biotic and biotic raw materials. The project encourages capacity building as well as transfer of knowledge. It expects to provide an innovation reference point for the European Institute of Innovation & Technology (EIT) Raw Materials (formerly the KIC Raw MatTERS), to coordinate the network involved in the European Innovation Partnership (EIP) on Raw Materials Commitments and relevant proposals funded under Horizon 2020. It provides a platform for identifying gaps and complementarities and enables their bridging. VERAM will be able to advise the European Commission and Member States on future research needs and policies to stimulate innovation and assist in overcoming fragmentation in the implementing the EIP Raw Materials Strategic Implementation Plan. VERAM looks for mutually beneficial information exchange, encourages cross-fertilization between actions undertaken by different raw material industries, and expects to accelerate exploitation of breakthrough innovations. One of the main outcomes of the project is the presentation of a common long term 2050 Vision and Roadmap for relevant raw materials including metals, industrial minerals and aggregates and wood. The Vision and Roadmap have the objective of highlighting the path to achieving the European Commission's ambitious target of 80% reduction in CO2 emissions by 2050.

40 CFR 428.103 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... not exceed— Metric units (kg/kkg of raw material) Oil and grease 2.0 0.73 BOD5 3.72 2.20 TSS 6.96 2.90 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 2.0 0.73 BOD5 3.72 2.20 TSS 6... raw material) Chromium 0.0086 0.0036 English units (lb/1,000 lb of raw material) Chromium 0.0086 0...

40 CFR 428.103 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... not exceed— Metric units (kg/kkg of raw material) Oil and grease 2.0 0.73 BOD5 3.72 2.20 TSS 6.96 2.90 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 2.0 0.73 BOD5 3.72 2.20 TSS 6... raw material) Chromium 0.0086 0.0036 English units (lb/1,000 lb of raw material) Chromium 0.0086 0...

40 CFR 428.102 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 2.0 0.73 BOD5 3.72 2.20 TSS 6.96 2.90 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 2.0 0.73 BOD5... units (kg/kkg of raw material) Chromium 0.0086 0.0036 English units (lb/1,000 lb of raw material...

Characterization of pore and crystal structure of synthesized LiBOB with varying quality of raw materials as electrolyte for lithium-ion battery

NASA Astrophysics Data System (ADS)

Lestariningsih, Titik; Ratri, Christin Rina; Wigayati, Etty Marty; Sabrina, Qolby

2016-02-01

Characterization of pore structure and crystal structure of the LiB(C2O4)2H2O or LIBOB compound has been performed in this study. These recent years, research regarding LiBOB electrolyte salt have been performed using analytical-grade raw materials, therefore this research was aimed to synthesized LiBOB electrolyte salt using the cheaper and abundant technical-grade raw materials. Lithium hydroxide (LiOH), oxalic acid dihydrate (H2C2O4.2H2O), and boric acid (H3BO3) both in technical-grade and analytical-grade quality were used as raw materials for the synthesis of LiBOB. Crystal structure characterization results of synthesized LiBOB from both technical-grade and analytical-grade raw materials have shown the existence of LiBOB and LiBOB hydrate phase with orthorombic structure. These results were also confirmed by FT-IR analysis, which showed the functional groups of LiBOB compounds. SEM analysis results showed that synthesized LiBOB has spherical structure, while commercial LiBOB has cylindrical structure. Synthesized LiBOB has a similar pore size of commercial LiBOB, i.e. 19 nm (mesoporous material). Surface area of synthesized LiBOB from analytical-grade raw materials and technical-grade materials as well as commercial LIBOB were 88.556 m2/g, 41.524 m2/g, and 108.776 m2/g, respectively. EIS analysis results showed that synthesized LiBOB from technical-grade raw materials has lower conductivity than synthesized LiBOB from analytical-grade raw materials.

Bioactive β-carbolines norharman and harman in traditional and novel raw materials for chicory coffee.

PubMed

Wojtowicz, Elżbieta; Zawirska-Wojtasiak, Renata; Przygoński, Krzysztof; Mildner-Szkudlarz, Sylwia

2015-05-15

The β-carboline compounds norharman and harman exhibit neuroactive activity in the human body. Chicory coffee has proved to be a source of β-carboline compounds. This study assessed the norharman and harman contents of traditional and novel raw materials for the production of chicory coffee, as well as in samples of chicory coffee with novel additives. The highest content of the β-carbolines among the traditional raw materials was recorded in roasted sugar beet (2.26 μg/g), while roasting the chicory caused a 25-fold increase in the content of norharman in this raw material (from 0.05 to 1.25 μg/g). In novel raw materials not subjected to the action of high temperature, β-carboline was not detected. Among the roasted novel raw materials, the highest contents of harman and norharman were found in artichokes. High harman levels were also recorded in roasted chokeberry. Copyright © 2014 Elsevier Ltd. All rights reserved.

Use of in vitro methods to rank surfactants for irritation potential in support of new product development.

PubMed

Casterton, P L; Potts, L F; Klein, B D

1994-08-01

11 surfactant raw materials with potential applications in light-duty liquid cleaning products were evaluated in vitro using a human skin analogue (ATS SKIN(2) Model ZK1100) for predicting cytotoxicity (MTT reduction) and inflammation [prostaglandin E(2) (PGE(2)) release]. Two of the 11 raw materials, both in the same compound family, were selected to be individually combined with each of the other nine in a 90:10 (raw:selected raw) mixture. Selection criteria were based on desired performance characteristics and low irritation potential as suggested from the individual surfactant assay data. To determine whether irritation potential was mitigated, MTT and PGE(2) scores were again determined for each of the 18 combinations with the resulting data being compared with the untreated raw material data. A plot of the data indicated that one of two selected materials may have an 'anti-irritant' effect. For raw materials with intrinsic MTT scores of less than 50 mug/ml and with the original data corrected for possible dilution effects, a statistical comparison between individual raw materials and the two sets of combinations was done using a one-sample analysis. Both cytotoxicity (MTT) and inflammation (PGE(2)) were significantly decreased by the milder of the two selected raw materials. By factoring the data into future new product decisions, this methodology has become a useful and practical tool for Amway product development.

Educating T-Shaped professionals to meet substitution challenges and developing business models for substitution and recycling

NASA Astrophysics Data System (ADS)

Arroyo, Ana; Mendibil Eguiluz, Javier; Sánchez Cupido, Laura

2018-03-01

One strategy to overcome the challenges related to critical raw materials (CRMs) is their substitution and recycling. However, the bright scientific idea, proof of concept or laboratory demonstration need to cross the valley of death in order to become stated as ‘a substitute’ instead of ‘a potential substitute’. Most PhD students and Post Docs specialize within a given thematic area; for example on specific materials or on substitution in a certain application. This specialization could limit the ability to generate innovations and profitable business models if there are not enough tools and skills to transform new knowledge and research results into an appealing value proposition towards customers and to a business opportunity for the current markets. The project proposes a framework for developing substitution and recycling related cross-sectorial skills and tools. These are applied for training business-related competences e.g. teamwork, management, communication, value proposition and business models design, especially within RTOs and industries. The proposed learning itinerary can radically improve the path from scientific proof of concept into innovation and lean start up or industrial market launch. The developed framework is tested by a pilot group having several topics within the areas of substitution and recycling of critical raw materials.

Synopsis of utilization research on SRIC raw materials

Treesearch

John B. Crist

1983-01-01

The take-home message of this paper is this: Raw materials produced using SRIC are suitable for many reconstituted end products. Juvenility, rapid growth, and bark contents do not greatly hinder the usefulness of the raw materials. In the future, increased industrial acceptance of SRIC methods and materials should be a major thrust and is discussed.

7 CFR 58.735 - Quality specifications for raw materials.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Quality specifications for raw materials. 58.735 Section 58.735 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING... specifications for raw materials. (a) Cheddar colby, washed or soaked curd, granular or stirred curd cheese...

Future Sources of Organic Raw Materials.

ERIC Educational Resources Information Center

Shapiro, Irving S.

1978-01-01

Examines the need for industrial organization, academic institutions, and national governments to agree on cooperative roles in planning the future raw materials demands of the chemical industry. Political and social concerns, as well as technical and economic considerations, are important to the raw material future of the industry. (MA)

PHASE I MATERIALS PROPERTY DATABASE DEVELOPMENT FOR ASME CODES AND STANDARDS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ren, Weiju; Lin, Lianshan

2013-01-01

To support the ASME Boiler and Pressure Vessel Codes and Standard (BPVC) in modern information era, development of a web-based materials property database is initiated under the supervision of ASME Committee on Materials. To achieve efficiency, the project heavily draws upon experience from development of the Gen IV Materials Handbook and the Nuclear System Materials Handbook. The effort is divided into two phases. Phase I is planned to deliver a materials data file warehouse that offers a depository for various files containing raw data and background information, and Phase II will provide a relational digital database that provides advanced featuresmore » facilitating digital data processing and management. Population of the database will start with materials property data for nuclear applications and expand to data covering the entire ASME Code and Standards including the piping codes as the database structure is continuously optimized. The ultimate goal of the effort is to establish a sound cyber infrastructure that support ASME Codes and Standards development and maintenance.« less

7 CFR 58.332 - Segregation of raw material.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Segregation of raw material. 58.332 Section 58.332 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... Procedures § 58.332 Segregation of raw material. The milk and cream received at the dairy plant shall meet...

7 CFR 58.332 - Segregation of raw material.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Segregation of raw material. 58.332 Section 58.332 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... Procedures § 58.332 Segregation of raw material. The milk and cream received at the dairy plant shall meet...

77 FR 2662 - Airworthiness Directives; Bombardier, Inc. Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-19

... to batches of raw material that did not meet required tensile strength. This proposed AD would..., Avox Systems Inc., revealed that the deformation was attributed to two (2) batches of raw material that... regulator on the oxygen cylinder, which was attributed to batches of raw material that did not meet required...

77 FR 31174 - Airworthiness Directives; Bombardier, Inc. Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-25

..., which was attributed to batches of raw material that did not meet required tensile strength. This AD... the deformation was attributed to two (2) batches of raw material that did not meet the required... deformation of the pressure regulator on the oxygen cylinder, which was attributed to batches of raw material...

Innovative Fly Ash Geopolymer-Epoxy Composites: Preparation, Microstructure and Mechanical Properties.

PubMed

Roviello, Giuseppina; Ricciotti, Laura; Tarallo, Oreste; Ferone, Claudio; Colangelo, Francesco; Roviello, Valentina; Cioffi, Raffaele

2016-06-09

The preparation and characterization of composite materials based on geopolymers obtained from fly ash and epoxy resins are reported for the first time. These materials have been prepared through a synthetic method based on the concurrent reticulation of the organic and inorganic components that allows the formation of hydrogen bonding between the phases, ensuring a very high compatibility between them. These new composites show significantly improved mechanical properties if compared to neat geopolymers with the same composition and comparable performances in respect to analogous geopolymer-based composites obtained starting from more expensive raw material such as metakaolin. The positive combination of an easy synthetic approach with the use of industrial by-products has allowed producing novel low cost aluminosilicate binders that, thanks to their thixotropicity and good adhesion against materials commonly used in building constructions, could be used within the field of sustainable building.

Innovative Fly Ash Geopolymer-Epoxy Composites: Preparation, Microstructure and Mechanical Properties

PubMed Central

Roviello, Giuseppina; Ricciotti, Laura; Tarallo, Oreste; Ferone, Claudio; Colangelo, Francesco; Roviello, Valentina; Cioffi, Raffaele

2016-01-01

The preparation and characterization of composite materials based on geopolymers obtained from fly ash and epoxy resins are reported for the first time. These materials have been prepared through a synthetic method based on the concurrent reticulation of the organic and inorganic components that allows the formation of hydrogen bonding between the phases, ensuring a very high compatibility between them. These new composites show significantly improved mechanical properties if compared to neat geopolymers with the same composition and comparable performances in respect to analogous geopolymer-based composites obtained starting from more expensive raw material such as metakaolin. The positive combination of an easy synthetic approach with the use of industrial by-products has allowed producing novel low cost aluminosilicate binders that, thanks to their thixotropicity and good adhesion against materials commonly used in building constructions, could be used within the field of sustainable building. PMID:28773582

Influence of man-made aluminosilicate raw materials on physical and mechanical properties of building materials.

NASA Astrophysics Data System (ADS)

Volodchenko, A. A.; Lesovik, V. S.; Stoletov, A. A.; Glagolev, E. S.; Volodchenko, A. N.; Magomedov, Z. G.

2018-03-01

It has been identified that man-made aluminosilicate raw materials represented by clay rock of varied genesis can be used as energy-efficient raw materials to obtain efficient highly-hollow non-autoclaved silicate materials. A technique of structure formation in the conditions of pressureless steam treatment has been offered. Cementing compounds of non- autoclaved silicate materials based on man-made aluminosilicate raw materials possess hydraulic properties that are conditioned by the process of further formation and recrystallization of calcium silicate hydrates, which optimizes the ratio between gellike and crystalline components and densifies the cementing compound structure, which leads to improvement of performance characteristics. Increasing the performance characteristics of the obtained products is possible by changing the molding conditions. For this reason, in order to create high-density material packaging and, as a result, to increase the strength properties of the products, it is reasonable to use higher pressure, under which raw brick is formed, which will facilitate the increase of quality of highly-hollow products.

An Architecture for Real-Time Processing of OSIRIS-REx Engineering and Science Data, from Raw Telemetry to PDS

NASA Astrophysics Data System (ADS)

Selznick, S. H.

2017-06-01

Herein we describe an architecture developed for processing engineering and science data for the OSIRIS-REx mission. The architecture is soup-to-nuts, starting with raw telemetry and ending with submission to PDS.

76 FR 62447 - Importer of Controlled Substances; Notice of Registration

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-07

... narcotic raw material are not appropriate. With regard to all non-Narcotic Raw Material drugs on this...-phenethyl-4-piperidine (8333)... II Phenylacetone (8501) II Opium, raw (9600) II Poppy Straw Concentrate...

EPR study of free radicals in bread

NASA Astrophysics Data System (ADS)

Yordanov, Nicola D.; Mladenova, Ralitsa

2004-05-01

The features of the recorded EPR spectra of paramagnetic species formed in bread and rusk are reported. The appearance of free radicals in them is only connected with their thermal treatment since the starting materials (flour and grains) exhibit very weak EPR signal. The obtained EPR spectra are complex and indicate that: (i) the relative number of paramagnetic species depends on the temperature and treating time of the raw product; (ii) the g-values are strongly temperature dependent with a tendency to coincide at t≥220 °C. Because of the relatively low (150-220 °C) temperature of thermal treatment, the studied free radicals can be assumed to appear in the course of the browning (Maillard) reaction and not to the carbonization of the material.

Chemical analysis of raw and processed Fructus arctii by high-performance liquid chromatography/diode array detection-electrospray ionization-mass spectrometry

PubMed Central

Qin, Kunming; Liu, Qidi; Cai, Hao; Cao, Gang; Lu, Tulin; Shen, Baojia; Shu, Yachun; Cai, Baochang

2014-01-01

Background: In traditional Chinese medicine (TCM), raw and processed herbs are used to treat the different diseases. Fructus Arctii, the dried fruits of Arctium lappa l. (Compositae), is widely used in the TCM. Stir-frying is the most common processing method, which might modify the chemical compositions in Fructus Arctii. Materials and Methods: To test this hypothesis, we focused on analysis and identification of the main chemical constituents in raw and processed Fructus Arctii (PFA) by high-performance liquid chromatography/diode array detection-electrospray ionization-mass spectrometry. Results: The results indicated that there was less arctiin in stir-fried materials than in raw materials. however, there were higher levels of arctigenin in stir-fried materials than in raw materials. Conclusion: We suggest that arctiin reduced significantly following the thermal conversion of arctiin to arctigenin. In conclusion, this finding may shed some light on understanding the differences in the therapeutic values of raw versus PFA in TCM. PMID:25422559

Raw materials in the manufacture of biotechnology products: regulatory considerations.

PubMed

Cordoba-Rodriguez, Ruth

2010-01-01

The Food and Drug Administration's Pharmaceutical cGMPs for the 21st Century initiative emphasizes science and risk-based approaches in the manufacture of drugs. These approaches are reflected in the International Conference on Harmonization (ICH) guidances ICH Q8, Q9, and Q10 and encourage a comprehensive assessment of the manufacture of a biologic, including all aspects of manufacture that have the potential to affect the finished drug product. Appropriate assessment and management of raw materials are an important part of this initiative. Ideally, a raw materials program should strive to assess and minimize the risk to product quality. With this in mind, risk-assessment concepts and control strategies will be discussed and illustrated by examples, with an emphasis on the impact of raw materials on cell substrates. Finally, the life cycle of the raw material will be considered, including its potential to affect the drug product life cycle. In this framework, the supply chain and the vendor-manufacturer relationship will be explored as important parts of an adequate raw materials control strategy.

Worldwide Mycotoxins Exposure in Pig and Poultry Feed Formulations

PubMed Central

Guerre, Philippe

2016-01-01

The purpose of this review is to present information about raw materials that can be used in pig and poultry diets and the factors responsible for variations in their mycotoxin contents. The levels of mycotoxins in pig and poultry feeds are calculated based on mycotoxin contamination levels of the raw materials with different diet formulations, to highlight the important role the stage of production and the raw materials used can have on mycotoxins levels in diets. Our analysis focuses on mycotoxins for which maximum tolerated levels or regulatory guidelines exist, and for which sufficient contamination data are available. Raw materials used in feed formulation vary considerably depending on the species of animal, and the stage of production. Mycotoxins are secondary fungal metabolites whose frequency and levels also vary considerably depending on the raw materials used and on the geographic location where they were produced. Although several reviews of existing data and of the literature on worldwide mycotoxin contamination of food and feed are available, the impact of the different raw materials used on feed formulation has not been widely studied. PMID:27886128

Raw material ‘criticality’—sense or nonsense?

NASA Astrophysics Data System (ADS)

Frenzel, M.; Kullik, J.; Reuter, M. A.; Gutzmer, J.

2017-03-01

The past decade has seen a resurgence of interest in the supply security of mineral raw materials. A key to the current debate is the concept of ‘criticality’. The present article reviews the criticality concept, as well as the methodologies used in its assessment, including a critical evaluation of their validity in view of classical risk theory. Furthermore, it discusses a number of risks present in global raw materials markets that are not captured by most criticality assessments. Proposed measures for the alleviation of these risks are also presented. We find that current assessments of raw material criticality are fundamentally flawed in several ways. This is mostly due to a lack of adherence to risk theory, and highly limits their applicability. Many of the raw materials generally identified as critical are probably not critical. Still, the flaws of current assessments do not mean that the general issue of supply security can simply be ignored. Rather, it implies that new assessments are required. While the basic theoretical framework for such assessments is outlined in this review, detailed method development will require a major collaborative effort between different disciplines along the raw materials value chain. In the opinion of the authors, the greatest longer-term challenge in the raw materials sector is to stop, or counteract the effects of, the escalation of unit energy costs of production. This issue is particularly pressing due to its close link with the renewable energy transition, requiring more metal and mineral raw materials per unit energy produced. The solution to this problem will require coordinated policy action, as well as the collaboration of scientists from many different fields—with physics, as well as the materials and earth sciences in the lead.

Theory and practice of conventional adventitious virus testing.

PubMed

Gregersen, Jens-Peter

2011-01-01

CONFERENCE PROCEEDING Proceedings of the PDA/FDA Adventitious Viruses in Biologics: Detection and Mitigation Strategies Workshop in Bethesda, MD, USA; December 1-3, 2010 Guest Editors: Arifa Khan (Bethesda, MD), Patricia Hughes (Bethesda, MD) and Michael Wiebe (San Francisco, CA) For decades conventional tests in cell cultures and in laboratory animals have served as standard methods for broad-spectrum screening for adventitious viruses. New virus detection methods based on molecular biology have broadened and improved our knowledge about potential contaminating viruses and about the suitability of the conventional test methods. This paper summarizes and discusses practical aspects of conventional test schemes, such as detectability of various viruses, questionable or false-positive results, animal numbers needed, time and cost of testing, and applicability for rapidly changing starting materials. Strategies to improve the virus safety of biological medicinal products are proposed. The strategies should be based upon a flexible application of existing and new methods along with a scientifically based risk assessment. However, testing alone does not guarantee the absence of adventitious agents and must be accompanied by virus removing or virus inactivating process steps for critical starting materials, raw materials, and for the drug product.

Ethanol production from chitosan by the nematophagous fungus Pochonia chlamydosporia and the entomopathogenic fungi Metarhizium anisopliae and Beauveria bassiana.

PubMed

Aranda-Martinez, Almudena; Naranjo Ortiz, Miguel Ángel; Abihssira García, Isabel Sofía; Zavala-Gonzalez, Ernesto A; Lopez-Llorca, Luis Vicente

2017-11-01

Chitin is the second most abundant biopolymer after cellulose and virtually unexplored as raw material for bioethanol production. In this paper, we investigate chitosan, the deacetylated form of chitin which is the main component of shellfish waste, as substrate for bioethanol production by fungi. Fungal parasites of invertebrates such as the nematophagous Pochonia chlamydosporia (Pc) or the entomopathogens Beauveria bassiana (Bb) and Metarhizium anisopliae (Ma) are biocontrol agents of plant parasitic nematodes (eg. Meloidogyne spp.) or insect pests such as the red palm weevil (Rhynchophorus ferrugineus). These fungi degrade chitin-rich barriers for host penetration. We have therefore tested the chitin/chitosanolytic capabilities of Pc, Bb and Ma for generating reducing sugars using chitosan as only nutrient. Among the microorganisms used in this study, Pc is the best chitosan degrader, even under anaerobic conditions. These fungi have alcohol dehydrogenase (ADH) and pyruvate decarboxylase (PDC) encoding genes in their genomes. We have therefore analyzed their ethanol production under anaerobic conditions using chitosan as raw material. P. chlamydosporia is the largest ethanol producer from chitosan. Our studies are a starting point to develop chitin-chitosan based biofuels. Copyright © 2017 Elsevier GmbH. All rights reserved.

Economic and kinetic studies of the biological production of farm energy and chemicals from biomass. Annual progress report, March 1979-August 1980

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gaddy, J.L.

1981-08-01

A system has been designed and built to test the technical and economic feasibility of producing farm energy from cellulosic residues. The system has the capacity to produPropinibactriume 1300 CF of biogas and 180 kwh per day, using four parallel batch anaerobic digesters which are agitated mechanically and heated with waste heat from the engine-generator. This system has been satisfactorily operated for a one year period utilizing native grasses as the raw material. Laboratory reactors have been operated to determine the proper inoculation ratio for starting batch cultures with cellulosic raw materials. Procedures for startup and operation of batch digestionmore » systems have been developed and are presented. Energy and economic analyses of the operation of the test unit have been performed. Studies to determine the fertilizer potential of anaerobic digestor sludge (from agricultural residues) have been conducted. Additional studies reported include determinations of the feasibility of separating the stages of anaerobic digestion, the production of acetic and propionic acids by the micro-organism Propionibacterium acidi-propionici, the production of methane from acid hydrolyzates, and the kinetics of the continuos digestion of corn stover.« less

Inventory control of raw material using silver meal heuristic method in PR. Trubus Alami Malang

NASA Astrophysics Data System (ADS)

Ikasari, D. M.; Lestari, E. R.; Prastya, E.

2018-03-01

The purpose of this study was to compare the total inventory cost calculated using the method applied by PR. Trubus Alami and Silver Meal Heuristic (SMH) method. The study was started by forecasting the cigarette demand from July 2016 to June 2017 (48 weeks) using additive decomposition forecasting method. The additive decomposition was used because it has the lowest value of Mean Abosolute Deviation (MAD) and Mean Squared Deviation (MSD) compared to other methods such as multiplicative decomposition, moving average, single exponential smoothing, and double exponential smoothing. The forcasting results was then converted as a raw material needs and further calculated using SMH method to obtain inventory cost. As expected, the result shows that the order frequency of using SMH methods was smaller than that of using the method applied by Trubus Alami. This affected the total inventory cost. The result suggests that using SMH method gave a 29.41% lower inventory cost, giving the cost different of IDR 21,290,622. The findings, is therefore, indicated that the PR. Trubus Alami should apply the SMH method if the company wants to reduce the total inventory cost.

Impact of Freezing Time on Dornic Acidity in Three Types of Milk: Raw Donor Milk, Mother's Own Milk, and Pasteurized Donor Milk.

PubMed

Vázquez-Román, Sara; Escuder-Vieco, Diana; García-Lara, Nadia Raquel; Alonso-Díaz, Clara; Lora, David; Martín-Pelegrina, María Dolores; Pallás-Alonso, Carmen Rosa

2016-03-01

Although under certain circumstances it is necessary to express milk, there are not many recommendations about the ideal storage conditions for human milk. The objectives of this study were to analyze the effects on Dornic acidity of frozen storage at -20 °C in three types of milk: raw donor milk, mother's own raw milk, and pasteurized donor milk. Forty-three samples of raw donor milk, 40 samples of pasteurized donor milk, and 16 samples of mother's own milk were analyzed. Dornic acidity was measured at time 0, before freezing. The remaining aliquots were frozen and analyzed after 1, 2, 3, and 4 weeks and after 2 and 3 months. In raw donor milk, the median acidity at the start was 3 °D (interquartile range [IQR] 2-3 °D); after 3 months, it was 5 °D (IQR 3-7 °D), with a significant increase in acidity after the second week. In mother's own milk, the mean acidity at the start was 3 °D (IQR 2-4 °D) and 7 °D (IQR 4-8 °D) at 3 months. The increase was significant after the third week. In pasteurized donor milk, the mean acidity was 3 °D (IQR 2-3 °D) at the start and 2 °D (IQR 2-3 °D) at the end. When comparing the three types of milk, there were significant differences from the first week between the two types of raw milk and the pasteurized milk (p < 0.01), but not between the two raw milks (p = 0.77). Dornic acidity in unpasteurized milk significantly increases with the duration of freezing, probably due to the action of lipases, which is lost with pasteurization. It would be advisable to reduce the length of freezing time for unpasteurized milk.

Renewable resources in the chemical industry--breaking away from oil?

PubMed

Nordhoff, Stefan; Höcker, Hans; Gebhardt, Henrike

2007-12-01

Rising prices for fossil-based raw materials suggest that sooner or later renewable raw materials will, in principle, become economically viable. This paper examines this widespread paradigm. Price linkages like those seen for decades particularly in connection with petrochemical raw materials are now increasingly affecting renewable raw materials. The main driving force is the competing utilisation as an energy source because both fossil-based and renewable raw materials are used primarily for heat, electrical power and mobility. As a result, prices are determined by energy utilisation. Simple observations show how prices for renewable carbon sources are becoming linked to the crude oil price. Whether the application calls for sugar, starch, virgin oils or lignocellulose, the price for the raw material rises with the oil price. Consequently, expectations regarding price trends for fossil-based energy sources can also be utilised for the valuation of alternative processes. However, this seriously calls into question the assumption that a rising crude oil price will favour the economic viability of alternative products and processes based on renewable raw materials. Conversely, it follows that these products and processes must demonstrate economic viability today. Especially in connection with new approaches in white biotechnology, it is evident that, under realistic assumptions, particularly in terms of achievable yields and the optimisation potential of the underlying processes, the route to utilisation is economically viable. This makes the paradigm mentioned at the outset at least very questionable.

Use of raw materials in the United States from 1900 through 2014

USGS Publications Warehouse

Matos, Grecia R.

2017-08-22

The economic growth of an industrialized nation such as the United States requires raw materials for construction (buildings, bridges, highways, and so forth), defense, and processing and manufacture of goods and services. Since the beginning of the 20th century, the types and quantities of raw materials used have increased and changed significantly. This fact sheet quantifies the amounts of raw materials (other than food and fuel) that have been used in the U.S. economy annually for a period of 115 years, from 1900 through 2014. It provides a broad overview of the quantity (weight) of nonfood and nonfuel materials used in the economy and illustrates the use and significance of raw nonfuel minerals in particular as building blocks of society.These data have been compiled to help the public and policymakers understand the changing annual flow of raw materials put into use in the United States. Such information can be helpful in assessing the potential effects of materials use on the environment, assessing materials’ intensity of use, and examining the role that these materials play in the economy. The data presented indicate the substitution and shift in materials usage from renewable to nonrenewable materials during the 20th century. The disaggregated quantities by commodity (not shown in this fact sheet) may be tested against supply adequacy and end of life issues.

Contamination of the cement raw material in a quarry site by seawater intrusion, Darica-Turkey

NASA Astrophysics Data System (ADS)

Camur, M. Zeki; Doyuran, Vedat

2008-02-01

The open pit mining nearby shoreline is planned to be extended into below sea level in order to use additional reserves of the cement raw material (marl). The raw material is currently contaminated by seawater intrusion below a depth of 20 m up to the distance of 90 m from shoreline. Seawater intrusion related contamination of the material used for the cement production was investigated by means of diffusion process for the future two below sea level mining scenarios covering 43 years of period. According to the results, chloride concentrations higher than the tolerable limit of a cement raw material would be present in the material about 10-25 cm inward from each discontinuity surface, controlling groundwater flow, located between 170 and 300 m landward from the shoreline at below sea level mining depths of 0-30 m. The estimations suggest that total amounts of dilution required for the contaminated raw material to reduce its concentration level to the tolerance limit with uncontaminated raw material are about 113- to 124-fold for scenario I (13 years of below sea level mining after 30 years of above sea level mining) and about 126- to 138-fold for scenario II (43 years of simultaneous above and below sea level minings).

77 FR 21532 - Glycine From the People's Republic of China: Preliminary Partial Affirmative Determination of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-10

... because it is producing glycine from raw materials of Indian origin and exporting such merchandise to the... find that there is no record evidence that AICO self produces glycine from Indian raw materials... exported to the United States glycine that it produced only from Indian raw materials. For a complete...

78 FR 69130 - Importer of Controlled Substances; Notice of Application: Johnson Matthey, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-18

... Concentrate (9670) II The company plans to import the listed controlled substances as raw materials, to be... requests for hearings on applications to import narcotic raw material are not appropriate. 72 FR 3417 (2007). In reference to the non-narcotic raw material, the company plans to import gram amounts to be used as...

[Contribution to the phytochemical study of polyphenols in ten hydroalcoholic extracts of Chamomile floss].

PubMed

Cioancă, Oana; Hăncianu, Monica; Spac, A; Miron, Anca; Stănescu, Ursula

2009-01-01

Continuing a series of studies that intend to evaluate the pharmaceutical quality of 10 commercial samples of chamomile, we tried to investigate the chemical composition of the hydroalcoholic extracts obtained in our laboratory, starting from this raw material. The qualitative and semiquantitative analysis of the extracts was done by HPLC means. All extractive solutions have a high content in ferulic acid, whereas the caffeic acid level is the lowest. Regarding the flavonoids, there are many quantitative differences between the samples: one extract lacking the rutoside and two of them having low apigenin-7-glucoside contents.

3D printing of polypropylene using the fused filament fabrication technique

NASA Astrophysics Data System (ADS)

Silva, A. F.; Carneiro, O. S.; Gomes, R.

2017-10-01

This work addresses the potential of polypropylene, neat (PP) and reinforced with short glass fibers (GRPP), as a candidate for the Fused Filament Fabrication (FFF)-based 3D printing technique. The entire production chain was evaluated, i.e., starting with PP and GRPP pellets, filaments were produced by extrusion and test samples were printed in different process conditions (different layers' thicknesses, deposition orientation and infill) with the in-house produced filaments. This strategy enabled a true comparison between parts printed (FFF) with parts manufactured by compression molding (CM), using exactly the same grade of raw material.

Thorium and Uranium in the Rock Raw Materials Used For the Production of Building Materials

NASA Astrophysics Data System (ADS)

Pękala, Agnieszka

2017-10-01

Thorium and uranium are constant components of all soils and most minerals thereby rock raw materials. They belong to the particularly dangerous elements because of their natural radioactivity. Evaluation of the content of the radioactive elements in the rock raw materials seems to be necessary in the early stage of the raw material evaluation. The rock formations operated from deposits often are accumulated in landfills and slag heaps where the concentration of the radioactive elements can be many times higher than under natural conditions. In addition, this phenomenon may refer to buildings where rock raw materials are often the main components of the construction materials. The global control system of construction products draws particular attention to the elimination of used construction products containing excessive quantities of the natural radioactive elements. In the presented study were determined the content of thorium and uranium in rock raw materials coming from the Bełachatów lignite deposit. The Bełchatów lignite deposit extracts mainly lignite and secondary numerous accompanying minerals with the raw material importance. In the course of the field works within the framework of the carried out work has been tested 92 samples of rocks of varied petrographic composition. There were carried out analyses of the content of the radioactive elements for 50 samples of limestone of the Jurassic age, 18 samples of kaolinite clays, and 24 samples of siliceous raw materials, represented by opoka-rocks, diatomites, gaizes and clastic rocks. The measurement of content of the natural radioactive elements thorium and uranium based on measuring the frequency counts of gamma quantum, recorded separately in measuring channels. At the same time performed measurements on volume patterns radioactive: thorium and uranium. The studies were carried out in Mazar spectrometer on the powdered material. Standardly performed ten measuring cycles, after which were calculated the concentration of radioactive elements in the sample. The highest concentration of thorium and uranium has been found in the clayey raw material. Their value was respectively from 8 to 12 mg/kg for thorium and from 2.3 to 3.5 mg/kg for uranium. In carbonate sediments the content of thorium was at the level from 0.5 to 2.1 mg/kg and uranium from 0.5-2.2 mg/kg. From a group of the siliceous raw materials the diatomite had a highest concentrations of radioactive elements where the content of thorium was from 1.5 to 1.8 mg/kg and uranium from 1.3 to 1.7 mg/kg.

DC Electric Arc Furnace Application for Production of Nickel-Boron Master Alloys

NASA Astrophysics Data System (ADS)

Alkan, Murat; Tasyürek, Kerem Can; Bugdayci, Mehmet; Turan, Ahmet; Yücel, Onuralp

2017-09-01

In this study, nickel-boron (Ni-B) alloys were produced via a carbothermic reduction starting from boric acid (H3BO3) with high-purity nickel oxide (NiO), charcoal, and wood chips in a direct current arc furnace. In electric arc furnace experiments, different starting mixtures were used, and their effects on the chemical compositions of the final Ni-B alloys were investigated. After the reduction and melting stages, Ni-B alloys were obtained by tapping from the bottom of the furnace. The samples from the designated areas were also taken and analyzed. The chemical composition of the final alloys and selected samples were measured with wet chemical analysis. The Ni-B alloys had a composition of up to 14.82 mass% B. The phase contents of the final alloys and selected samples were measured using x-ray diffraction (XRD). The XRD data helped predict possible reactions and reaction mechanisms. The material and energy balance calculations were made via the XRD Rietveld and chemical compositions. Nickel boride phases started to form 600 mm below the surface. The targeted NiB phase was detected at the tapping zone of the crucible (850-900 mm depth). The energy consumption was 1.84-4.29 kWh/kg, and the electrode consumption was 10-12 g/kg of raw material charged.

A membrane-integrated fermentation reactor system: its effects in reducing the amount of sub-raw materials for D-lactic acid continuous fermentation by Sporolactobacillus laevolacticus.

PubMed

Mimitsuka, Takashi; Na, Kyungsu; Morita, Ken; Sawai, Hideki; Minegishi, Shinichi; Henmi, Masahiro; Yamada, Katsushige; Shimizu, Sakayu; Yonehara, Tetsu

2012-01-01

Continuous fermentation by retaining cells with a membrane-integrated fermentation reactor (MFR) system was found to reduce the amount of supplied sub-raw material. If the amount of sub-raw material can be reduced, continuous fermentation with the MFR system should become a more attractive process for industrialization, due to decreased material costs and loads during the refinement process. Our findings indicate that the production rate decreased when the amount of the sub-raw material was reduced in batch fermentation, but did not decrease during continuous fermentation with Sporolactobacillus laevolacticus. Moreover, continuous fermentation with a reduced amount of sub-raw material resulted in a productivity of 11.2 g/L/h over 800 h. In addition, the index of industrial process applicability used in the MFR system increased by 6.3-fold as compared with the conventional membrane-based fermentation reactor previously reported, suggesting a potential for the industrialization of this D-lactic acid continuous fermentation process.

75 FR 67788 - Self-Regulatory Organizations; The NASDAQ Stock Market LLC; Notice of Filing of Proposed Rule...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-03

... Business Plan is to Purchase and Stockpile Raw Materials or Other Commodities In the case of a Company... stockpile quantities of a raw material or other commodity (``commodity stockpiling companies'' or ``CSCs... invest at least 85% of the net proceeds of the initial public offering in the raw material or other...

Data on volatile compounds in fermented materials used for salmon fish sauce production.

PubMed

Nakano, Mitsutoshi; Sagane, Yoshimasa; Koizumi, Ryosuke; Nakazawa, Yozo; Yamazaki, Masao; Watanabe, Toshihiro; Takano, Katsumi; Sato, Hiroaki

2018-02-01

This article describes the analysis of volatile compounds in fermented materials used for salmon fish sauce production via gas chromatography/mass spectrometry (GC/MS). Ten types of fish sauces were produced from raw salmon materials, including various proportions of flesh, viscera, inedible portion (heads, fins, and backbones), and soft roe, by mixing them with salt and allowing them to ferment for up to three months. The volatile compounds were captured by a solid-phase microextraction method and then applied to GC/MS for separation and identification of the compounds in the fish sauce products. The number of volatile compounds identified in the starting materials varied from 15 to 29 depending on the ingredients. The number of compounds in the final fish sauce products was reduced by 3.4-94.7% of that in the original material. The retention times and names of the identified compounds, as well as their relative peak areas, are provided in a Microsoft Excel Worksheet.

Large-scale production of PMMA/SWCNT composites based on SWCNT modified with PMMA.

PubMed

Fraser, Robin Anderson; Stoeffler, Karen; Ashrafi, Behnam; Zhang, Yunfa; Simard, Benoit

2012-04-01

In this work, a two-step method consisting of in situ polymerization of polymethyl methacrylate (PMMA) in the presence of single-walled carbon nanotubes (SWCNT), followed by the redispersion of the resulting compound in dimethylformamide (DMF), was used to fabricate SWCNT modified with PMMA (SWCNT-PMMA). Raman spectroscopy revealed that PMMA was merely wrapped around the SWCNT when raw SWCNT or purified SWCNT were used as the starting material. However, PMMA was covalently bonded to SWCNT when acid treated SWCNT (SWCNT-COOH) was used as the starting material. SWCNT-PMMA compounds were further diluted in pure PMMA by conventional melt compounding at large scale (several kilograms) to obtain transparent composites containing 0.09 wt % SWCNT. The micro- and nano-dispersion of the SWCNT in the composites were analyzed using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The thermal and mechanical properties of the composites were determined by thermal gravimetric analysis (TGA), differential scanning calorimetry (DSC), tensile testing, and Charpy impact testing. At the the low SWCNT loading studied, the tensile properties remain unchanged, whereas the impact strength improves by 20%.

Peculiarities of non-autoclaved lime wall materials production using clays

NASA Astrophysics Data System (ADS)

Volodchenko, A. A.; Lesovik, V. S.; Cherepanova, I. A.; Volodchenko, A. N.; Zagorodnjuk, L. H.; Elistratkin, M. Y.

2018-03-01

At present, the development and implementation of energy saving technologies for building materials production, which correspond to modern trends of «green» technologies, become ever more popular. One of the most widely spread wall materials today is a lime brick and stones. The primary raw goods used in production of such materials are quarziferous rocks. However, they have some disadvantages, including low strength index at the intermediate phase of their production, especially in case with a raw brick, which is an issue in the production of high-hollow goods due to low strength index of raw materials and the nonoptimal matrix structure. The conducted experiments confirmed the possibility to control structurization of building composites due to application of nonconventional argillous raw materials. Besides, the material and mineral composition of nonconventional clay rocks ensures the optimal microstructure thus providing for the production of efficient wall building materials via energy saving technology.

One step sintering of homogenized bauxite raw material and kinetic study

NASA Astrophysics Data System (ADS)

Gao, Chang-he; Jiang, Peng; Li, Yong; Sun, Jia-lin; Zhang, Jun-jie; Yang, Huan-ying

2016-10-01

A one-step sintering process of bauxite raw material from direct mining was completed, and the kinetics of this process was analyzed thoroughly. The results show that the sintering kinetics of bauxite raw material exhibits the liquid-phase sintering behavior. A small portion of impurities existed in the raw material act as a liquid phase. After X-ray diffraction analyses, scanning electron microscopy observations, and kinetics calculations, sintering temperature and heating duration were determined as the two major factors contributing to the sintering process and densification of bauxite ore. An elevated heating temperature and longer duration favor the densification process. The major obstacle for the densification of bauxite material is attributed to the formation of the enclosed blowhole during liquid-phase sintering.

Impact of functionalized particle structure on roll compaction/dry granulation and tableting of calcium carbonate.

PubMed

Grote, Simon; Kleinebudde, Peter

2018-06-10

The influence of a functionalized raw material particle structure on the granulation behavior and tabletabilty of calcium carbonate (CaCO 3 ) was investigated. Therefore, a milled grade of CaCO 3 was compared to different binary mixtures of milled and functionalized CaCO 3 . Relevant properties of raw materials, ribbons and granules were measured. The starting materials and two fractions of dry granules were compressed to tablets. The tabletability of granules was compared to that of the powders and the influence of specific compaction force and granule size on tablet tensile strength was evaluated. Adding functionalized particles drastically influenced the granulation and tableting behavior of CaCO 3 . Increasing proportions increased the ribbon porosity and granule size. Tensile strength of tablets from powder mixtures and granules was increased as well. Nevertheless, adding functionalized CaCO 3 led to a loss in tabletability induced by a previous compaction step to an extent depending on its proportion in the formulation. A clear influence of the particle morphology on granulation and tableting behavior was demonstrated by the study. The functionalized structure showed aspects of a more plastic deformation behavior. Adding functionalized CaCO 3 to a mixture, even in small amounts, seemed to be beneficial to increase granule size and tablet strength. Copyright © 2018 Elsevier B.V. All rights reserved.

Choice and validation of a near infrared spectroscopic application for the identity control of starting materials. practical experience with the EU draft Note for Guidance on the use of near infrared spectroscopy by the pharmaceutical industry and the data to be forwarded in part II of the dossier for a marketing authorization.

PubMed

Vredenbregt, M J; Caspers, P W J; Hoogerbrugge, R; Barends, D M

2003-11-01

Recently the CPMP/CVMP sent out for consultation the draft Note for Guidance (dNfG) on the use of near infrared spectroscopy (NIRS) by the pharmaceutical industry and the data to be forwarded in part II of the dossier for a marketing authorization. We explored the practicability of this dNfG with respect to the verification of the correct identity of starting materials in a generic tablet-manufacturing site. Within the boundaries of the dNfG, a release procedure was developed for 12 substances containing structurally related compounds and substances differing only in particle size. For the method development literature data were also taken into consideration. Good results were obtained with wavelength correlation (WC), applied on raw spectra or second derivative spectra both without smoothing. The defined threshold of 0.98 for raw spectra differentiated between all molecular structures. Both methods were found to be robust over a period of 1 year. For the differentiation between the different particle sizes a subsequent second chemometric technique had to be used. Soft independent modelling of class analogy (SIMCA) with a probability level of 0.01 proved suitable. Internal and external validation I according to the dNfG showed no incorrect rejections or false acceptances. External validation II according to the dNfG was carried out with 95 potentially interfering substances from which 46 were tested experimentally. Macrogol 400 was not distinguished from macrogol 300. For the complete verification of the identity of macrogol 300 test A of the European Pharmacopoeia is needed in addition to the NIRS application. A release procedure developed with WC applied on raw spectra and SIMCA as a second method, which is different from the preferred method of the dNfG, was tested in practice with good results. We conclude that the dNfG has good practicability and that deviations from the preferred methods of the dNfG can also give good differentiation.

Tracing and control of raw materials sourcing for vaccine manufacturers.

PubMed

Faretra Peysson, Laurence

2010-05-01

The control of the raw materials used to manufacture vaccines is mandatory; therefore, a very clear process must be in place to guarantee that raw materials are traced. Those who make products or supplies used in vaccine manufacture (suppliers of culture media, diagnostic tests, etc.) must apply quality systems proving that they adhere to certain standards. ISO certification, Good Manufacturing Practices for production sites and the registration of culture media with a 'Certificate of Suitability' from the European Directorate for the Quality of Medicines and Healthcare are reliable quality systems pertaining to vaccine production. Suppliers must assure that each lot of raw materials used in a product that will be used in vaccine manufacture adheres to the level of safety and traceability required. Incoming materials must be controlled in a single 'Enterprise Resource Planning' system which is used to document important information, such as the assignment of lot number, expiration date, etc. Ingredients for culture media in particular must conform to certain specifications. The specifications that need to be checked vary according to the ingredient, based on the level of risk. The way a raw material is produced is also important, and any aspect relative to cross-contamination, such as the sanitary measures used in producing and storing the raw material must be checked as well. In addition, suppliers can reduce the risk of viral contamination of raw materials by avoiding purchases in countries where a relevant outbreak is currently declared. 2010 The International Association for Biologicals. Published by Elsevier Ltd. All rights reserved.

40 CFR 428.62 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.42 0.15 TSS 0.80 0.40 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.42 0.15... material) Lead 0.0017 0.0007 English units (lb/1,000 lb of raw material) Lead 0.0017 0.0007 (c) The...

Innovative hyperspectral imaging (HSI) based techniques applied to end-of-life concrete drill core characterization for optimal dismantling and materials recovery

NASA Astrophysics Data System (ADS)

Bonifazi, Giuseppe; Picone, Nicoletta; Serranti, Silvia

2015-02-01

The reduction of EOL concrete disposal in landfills, together with a lower exploitation of primary raw materials, generates a strong interest to develop, set-up and apply innovative technologies to maximize Construction and Demolition Waste (C&DW) conversion into useful secondary raw materials. Such a goal can be reached starting from a punctual in-situ efficient characterization of the objects to dismantle in order to develop demolition actions aimed to set up innovative mechanical-physical processes to recover the different materials and products to recycle. In this paper an innovative recycling-oriented characterization strategy based on HyperSpectral Imaging (HSI) is described in order to identify aggregates and mortar in drill core samples from end-of-life concrete. To reach this goal, concrete drill cores from a demolition site were systematically investigated by HSI in the short wave infrared field (1000-2500 nm). Results obtained by the adoption of the HSI approach showed as this technology can be successfully applied to analyze quality and characteristics of C&DW before dismantling and as final product to reutilise after demolition-milling-classification actions. The proposed technique and the related recognition logics, through the spectral signature detection of finite physical domains (i.e. concrete slice and/or particle) of different nature and composition, allows; i) to develop characterization procedures able to quantitatively assess end-of-life concrete compositional/textural characteristics and ii) to set up innovative sorting strategies to qualify the different materials constituting drill core samples.

Oat raw materials and bakery products - amino acid composition and celiac immunoreactivity.

PubMed

Mickowska, Barbara; Litwinek, Dorota; Gambuś, Halina

2016-01-01

The aim of this study was to compare the biochemical and immunochemical properties of avenins in some special oat raw materials and additionally the possibility of using them as a raw material for the gluten-free bakery products. The compared oat raw materials were - oat flakes, commercial oat flours (including gluten-free oat flour) and residual oat flour, which is by-product of β-glucan preparation. Biochemical characteristic included amino acid compositions and SDS-PAGE profiles of extracted avenins. The immunochemical reactivity with polyclonal anti-gluten and monoclonal anti-gliadin antibodies was evaluated qualitatively and quantitatively by immunoblotting and ELISA methods. Additionally, experimental bakery products made of examined raw materials were assessed according to their suitability for the celiac patients' diet. The highest protein content was measured in the β-glucan preparation "Betaven" and gluten-free oat flour. Proteins of all materials are rich in glutamic and aspartic acid, leucine and arginine. Proportions of amino acids in avenins extracted from most of oat raw materials are similar, excluding gluten-free oat flour, which has a very low avenin content and proportions of individual amino acids are different. The SDS-PAGE protein pattern consisted of proteins with molecular weight of about 25-35 kDa. Polyclonal anti-gluten anti-body recognized all protein fractions of molecular weight higher than 20 kDa. Quantitative ELISA analysis shows that the majority of samples has a gliadin-like protein content within the range of 80-260 mg/kg, excluding gluten-free flours and corresponding bakery products. Altogether, β-glucan preparation has extremely high level of gliadin-like proteins. In the examined oat raw materials and foods the contents of immunoreactive amino acid sequences exceeded the limit of 20 mg/kg (considered as gluten-free) except for gluten-free flours (oat and  the prepared mixture) and the bakery products based on gluten-free flours. Unfortunately, the rest of oat raw materials and products cannot be considered gluten-free.

Wireless "Jump" Starts for Partly Disabled Equipment

NASA Technical Reports Server (NTRS)

Castle, K. D.

1986-01-01

Equipment activated when normal remote starting does not work Beam from nearby station first carries raw energy and then subsystemactivating signals to equipment crippled by discharged storage batteries. Operators start up equipment without approaching it under hazardous conditions. Potential terrestrial applications for scheme include starting of robots on such remotely-controlled hazardous tasks as handling of explosives or retrieval or deposition of objects in hostile environments.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Venkatraman, A.; Walawender, W.P.; Fan, L.T.

The term, activated carbon, is a generic name for a family of carbonaceous materials with well-developed porosities and consequently, large adsorptive capacities. Activated carbons are increasingly being consumed worldwide for environmental applications such as separation of volatiles from bulk gases and purification of water and waste-water streams. The global annual production is estimated to be around 300 million kilograms, with a rate of increase of 7% each year. Activated carbons can be prepared from a variety of raw materials. Approximately, 60% of the activated carbons generated in the United States is produced from coal; 20%, from coconut shells; and themore » remaining 20% from wood and other sources of biomass. The pore structure and properties of activated carbons are influenced by the nature of the starting material and the initial physical and chemical conditioning as well as the process conditions involved in its manufacture. The porous structures of charcoals and activated carbons obtained by the carbonization of kernels have been characterized.« less

Fluorescence of aqueous solutions of commercial humic products

NASA Astrophysics Data System (ADS)

Gosteva, O. Yu.; Izosimov, A. A.; Patsaeva, S. V.; Yuzhakov, V. I.; Yakimenko, O. S.

2012-01-01

We have studied the spectral luminescence characteristics of aqueous solutions of humic products obtained from different raw material sources, and their behavior as the excitation wavelength increases from 270 nm to 355 nm. We have identified differences in the spectral properties of industrial humic products from coalified materials, lignin-containing organic waste, and humic products from plant raw material (peat, sapropel, vermicompost). We have shown that humic products from plant raw material have spectral properties closer to those for humic substances in natural water or soil than humic products from coalified materials.

Microbiological Spoilage of Spices, Nuts, Cocoa, and Coffee

NASA Astrophysics Data System (ADS)

Pinkas, Joan M.; Battista, Karen; Morille-Hinds, Theodora

Spices, nuts, cocoa, and coffee are raw materials that may be used alone or as ingredients in the manufacture of processed food products. The control of microbiological spoilage of these raw materials at the ingredient stage will enable the food processor to better assure the production of high-quality foods with an acceptable shelf life. While this chapter is limited to four materials, many of the spoilage control procedures recommended can also be applied to other raw materials of a similar nature.

Quality assessment of baby food made of different pre-processed organic raw materials under industrial processing conditions.

PubMed

Seidel, Kathrin; Kahl, Johannes; Paoletti, Flavio; Birlouez, Ines; Busscher, Nicolaas; Kretzschmar, Ursula; Särkkä-Tirkkonen, Marjo; Seljåsen, Randi; Sinesio, Fiorella; Torp, Torfinn; Baiamonte, Irene

2015-02-01

The market for processed food is rapidly growing. The industry needs methods for "processing with care" leading to high quality products in order to meet consumers' expectations. Processing influences the quality of the finished product through various factors. In carrot baby food, these are the raw material, the pre-processing and storage treatments as well as the processing conditions. In this study, a quality assessment was performed on baby food made from different pre-processed raw materials. The experiments were carried out under industrial conditions using fresh, frozen and stored organic carrots as raw material. Statistically significant differences were found for sensory attributes among the three autoclaved puree samples (e.g. overall odour F = 90.72, p < 0.001). Samples processed from frozen carrots show increased moisture content and decrease of several chemical constituents. Biocrystallization identified changes between replications of the cooking. Pre-treatment of raw material has a significant influence on the final quality of the baby food.

Energy and raw material potentials of wood residue in the Pacific Coast States: a summary of a preliminary feasibility investigation.

Treesearch

John B. Grantham; Eldon Estep; John M. Pierovich; Harold Tarkow; Thomas C. Adams

1974-01-01

Results are reported of a preliminary investigation of feasibility of using wood residue to meet energy and raw material needs in the Pacific Coast States. Magnitude of needs was examined and volume of logging-residue and unused mill residue was estimated. Costs of obtaining and preprocessing logging residue for energy and pulp and particle board raw material were...

Perchlorate in Fertilizers

DTIC Science & Technology

1999-09-01

Harrington , showed that with respect to mixed water analysis containing TDS at greater 1,000 ppm, the performance of the AS-5 column is not as robust...to note, these raw test materials were heterogeneous. Regardless of mixing time and mesh quality, dividing the raw test materials for laboratory...raw test material was prepared and shipped to seven laboratories for blind analysis. The suspension was prepared by 4 mixing the solid sample with

Indonesian CPO availability analysis to support food and energy security: a system dynamic approach

NASA Astrophysics Data System (ADS)

Rahman, T.; Arkeman, Y.; Setyaningsih, D.; Saparita, R.

2017-05-01

The development of biofuels could be a solution to overcome the energy problem. One of biofuel that has the potential to be developed, namely palm oil biodiesel that is also the raw material for food. As a provider of CPO raw materials, the production of palm biodiesel could trigger competitions, from biofuels demand growth and utilization of agricultural resources. Thus, it needs to be analyzed to determine the adequency of CPO supply to fulfill the need of food and policy recomendation which sets the development of palm oil biodiesel can be synergies with food need especially for the supply of raw material CPO. To obtain the optimal policy in the synergy between the raw material of CPO for food and energy is a need to establish some policy scenarios that allow to be applied and then chosen the best policy alternative of all scenarios. The purpose of this research were to : 1) analysis the availability of CPO to meet the needs of food and energy, 2) provide policy recommendation with regard biodiesel development of food security. The model made used system dynamic method. Several scenarios that used in the model are: 1) existing condition, 2) The scenario increase biodiesel production capacity and increase land productivity, 3) reduction scenario CPO export by 30%, 4) scenario use othe raw material for biodiesel by 20%. The simulation results showed the availability of CPO raw materials would answer all needs of both food and biodiesel when there was an increase in productivity, diversification of raw materials, and also a reduction in palm oil exports. It was needed an integrated policy from upstream to downstream along with the consistency of implementation. Policy suggestions that could be considered were increased productivity through agricultural intensification, enforcement disincentive policies of CPO to exports, and development of non-CPO biodiesel raw materials and development of renewable energy.

Salt-soluble proteins from wheat-derived foodstuffs show lower allergenic potency than those from raw flour.

PubMed

de Gregorio, Marta; Armentia, Alicia; Díaz-Perales, Araceli; Palacín, Arantxa; Dueñas-Laita, Antonio; Martín, Blanca; Salcedo, Gabriel; Sánchez-Monge, Rosa

2009-04-22

Salt-soluble proteins from wheat flour have been described as main allergens associated with both baker's asthma and food allergy. However, most studies have used raw flour as starting material, thus not considering potential changes in allergenic properties induced by the heat treatment and other industrial processing to produce wheat-derived foodstuffs. Salt extracts from different commercial wheat-derived products were obtained and their allergenic properties investigated by IgE-immunodetection, ELISA assays, and skin prick test. The IgE-binding capacity of salt-soluble proteins from commercial breads and cooked pastas was reduced around 50% compared with that of raw flour, the reduction being less dramatic in noncooked pastas and biscuits. Several wheat-derived foodstuffs showed major IgE-binding components of 20 and 35 kDa, identified as avenin-like and globulin proteins, respectively. These proteins, as well as most flour and bread salt-soluble proteins, were hydrolyzed when subjected to simulated gastrointestinal digestion. However, the digested products still exhibited a residual IgE-binding capacity. Therefore, processing of wheat flour to obtain derived foodstuffs decreases the IgE binding-capacity of the major salt-soluble wheat proteins. Moreover, simulated gastric fluid digestion further inactivates some heat-resistant IgE-binding proteins.

77 FR 31388 - Importer of Controlled Substances; Notice of Application; Noramco, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-25

... material are not appropriate. 72 FR 3417 (2007). In regard to the non-narcotic raw material, any bulk... following basic classes of controlled substances: Drug Schedule Phenylacetone (8501) II Opium, raw (9600) II Poppy Straw Concentrate (9670) II Tapentadol (9780) II The company plans to import the raw Opium (9600...

40 CFR 428.105 - Standards of performance for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 2.0 0.73 BOD5 3.72 2.20 TSS 6.96 2.90 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 2.0 0.73 BOD5... daily values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material) Chromium 0...

40 CFR 428.105 - Standards of performance for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 2.0 0.73 BOD5 3.72 2.20 TSS 6.96 2.90 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 2.0 0.73 BOD5... daily values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material) Chromium 0...

A Development Strategy for Creating a Suite of Reference Materials for the in-situ Microanalysis of Non-conventional Raw Materials

NASA Astrophysics Data System (ADS)

Renno, A. D.; Merchel, S.; Michalak, P. P.; Munnik, F.; Wiedenbeck, M.

2010-12-01

Recent economic trends regarding the supply of rare metals readily justify scientific research into non-conventional raw materials, where a particular need is a better understanding of the relationship between mineralogy, microstructure and the distribution of key metals within ore deposits (geometallurgy). Achieving these goals will require an extensive usage of in-situ microanalytical techniques capable of spatially resolving material heterogeneities which can be key for understanding better resource utilization. The availability of certified reference materials (CRMs) is an essential prerequisite for (1) validating new analytical methods, (2) demonstrating data quality to the contracting authorities, (3) supporting method development and instrument calibration, and (4) establishing traceability between new analytical approaches and existing data sets. This need has led to the granting of funding by the European Union and the German Free State of Saxony for a program to develop such reference materials . This effort will apply the following strategies during the selection of the phases: (1) will use exclusively synthetic minerals, thereby providing large volumes of homogeneous starting material. (2) will focus on matrices which are capable of incorporating many ‘important’ elements while avoid exotic compositions which would not be optimal matrix matches. (3) will emphasise those phases which remain stable during the various microanalytical procedure. This initiative will assess the homogeneity of the reference materials at sampling sizes ranging between 50 and 1 µm; it is also intended to document crystal structural homogeneity too, as this too may potentially impact specific analytical methods. As far as possible both definitive methods as well as methods involving matrix corrections will be used for determining the compositions of the of the individual materials. A critical challenge will be the validation of the determination of analytes concentrations as sub-µg sampling masses. It is planned to cooperate with those who are interested in the development of such reference materials and we invite them to take part in round-robin exercises.

Characterization of Thallium Bromide Detectors Made From Material Purified by the Filter Method

NASA Astrophysics Data System (ADS)

Onodera, Toshiyuki; Hitomi, Keitaro; Tada, Tsutomu; Shoji, Tadayoshi; Mochizuki, Katsumi

2013-10-01

Thallium bromide (TlBr) has been regarded as candidate detector materials for the gamma-ray spectrometers operating at room temperature. In this study, a simple and rapid method, the filter method, was performed to purify a raw TlBr material used for fabrication of TlBr detectors. The material was loaded on shards of crashed quartz and installed in a Pyrex tube, and was melted using a furnace. A purified material passing through interspaces of the shards of quartz was collected in a quartz ampoule located at the outlet of the Pyrex tube. After the purification, impurities colored black extracted from the raw material remained. TlBr crystals were then grown by the travelling molten zone method both from the raw material and the purified material. TlBr detectors were fabricated from the grown crystals, and were characterized by measuring mobility-lifetime products (μτ) for carriers and gamma-ray spectra ( 137Cs) at room temperature. μτ for electrons of a TlBr detector fabricated from the purified material was around 5 times higher than that of a detector fabricated from the raw material.

Satellite relay telemetry of seismic data in earthquake prediction and control

USGS Publications Warehouse

Jackson, Wayne H.; Eaton, Jerry P.

1971-01-01

The Satellite Telemetry Earthquake Monitoring Program was started in FY 1968 to evaluate the applicability of satellite relay telemetry in the collection of seismic data from a large number of dense seismograph clusters laid out along the major fault systems of western North America. Prototype clusters utilizing phone-line telemetry were then being installed by the National Center for Earthquake Research (NCER) in 3 regions along the San Andreas fault in central California; and the experience of installing and operating the clusters and in reducing and analyzing the seismic data from them was to provide the raw materials for evaluation in the satellite relay telemetry project.

Ethanol Production from Traditional and Emerging Raw Materials

NASA Astrophysics Data System (ADS)

Rudolf, Andreas; Karhumaa, Kaisa; Hahn-Hägerdal, Bärbel

The ethanol industry of today utilizes raw materials rich in saccharides, such as sugar cane or sugar beets, and raw materials rich in starch, such as corn and wheat. The concern about supply of liquid transportation fuels, which has brought the crude oil price above 100 /barrel during 2006, together with the concern about global warming, have turned the interest towards large-scale ethanol production from lignocellulosic materials, such as agriculture and forestry residues. Baker's yeast Saccharomyces cerevisiae is the preferred fermenting microorganism for ethanol production because of its superior and well-documented industrial performance. Extensive work has been made to genetically improve S. cerevisiae to enable fermentation of lignocellulosic raw materials. Ethanolic fermentation processes are conducted in batch, fed-batch, or continuous mode, with or without cell recycling, the relative merit of which will be discussed.

Solutions for Critical Raw Materials under Extreme Conditions: A Review

PubMed Central

Grilli, Maria Luisa; Bellezze, Tiziano; Gamsjäger, Ernst; Rinaldi, Antonio; Novak, Pavel; Balos, Sebastian; Piticescu, Radu Robert; Ruello, Maria Letizia

2017-01-01

In Europe, many technologies with high socio-economic benefits face materials requirements that are often affected by demand-supply disruption. This paper offers an overview of critical raw materials in high value alloys and metal-matrix composites used in critical applications, such as energy, transportation and machinery manufacturing associated with extreme working conditions in terms of temperature, loading, friction, wear and corrosion. The goal is to provide perspectives about the reduction and/or substitution of selected critical raw materials: Co, W, Cr, Nb and Mg. PMID:28772645

Hydrogenated cottonseed oil as raw material for biobased materials

USDA-ARS?s Scientific Manuscript database

There has been a lot of recent interest in using vegetable oils as biodegradable and renewable raw materials for the syntheses of various biobased materials. Although most of the attention has been paid to soybean oil thus far, cottonseed oil is a viable alternative. An advantage of cottonseed oil...

Identification of Particles in Parenteral Drug Raw Materials.

PubMed

Lee, Kathryn; Lankers, Markus; Valet, Oliver

2018-04-18

Particles in drug products are not good and are therefore regulated. These particles can come from the very beginning of the manufacturing process, from the raw materials. To prevent particles, it is important to understand what they are and where they come from so the raw material quality, processing, and shipping can be improved. Thus, it is important to correctly identify particles seen in raw materials. Raw materials need to be of a certain quality with respect to physical and chemical composition, and need to have no contaminants in the form of particles which could contaminate the product or indicate the raw materials are not pure enough to make a good quality product. Particles are often seen when handling raw materials due to color, size, or shape characteristics different from those in the raw materials. Particles may appear to the eye to be very different things than they actually are, so microscope, chemical, and elemental analyses are required for accuracy in proper identification. This paper shows how using three different spectroscopy tools correctly and together can be used to identify particles from extrinsic, intrinsic, and inherent particles. Sources of materials can be humans and the environment (extrinsic), from within the process (intrinsic), and part of the formulation (inherent). Microscope versions of Raman spectroscopy, laser-induced breakdown spectroscopy (LIBS), and IR spectroscopy are excellent tools for identifying particles because they are fast and accurate techniques needing minimal sample preparation that can provide chemical composition as well as images that can be used for identification. The micro analysis capabilities allow for easy analysis of different portions of samples so multiple components can be identified and sample preparation can be reduced. Using just one of these techniques may not be sufficient to give adequate identification results so that the source of contamination can be adequately identified. The complementarity of the techniques provides the advantage of identifying various chemical and molecular components, as well as elemental and image analyses. Correct interpretation of the results from these techniques is also very important. Copyright © 2018, Parenteral Drug Association.

40 CFR 428.73 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.26 0.093 TSS 0.50 0.25 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.26 0.093 TSS 0.50 0.25 pH... Average of daily values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material...

40 CFR 428.53 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.70 0.25 TSS 1.28 0.64 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.70 0.25 TSS 1.28 0.64 pH... Average of daily values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material...

40 CFR 428.63 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.42 0.15 TSS 0.80 0.40 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.42 0.15 TSS 0.80 0.40 pH... Average of daily values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material...

40 CFR 428.53 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.70 0.25 TSS 1.28 0.64 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.70 0.25 TSS 1.28 0.64 pH... Average of daily values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material...

40 CFR 428.73 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.26 0.093 TSS 0.50 0.25 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.26 0.093 TSS 0.50 0.25 pH... Average of daily values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material...

40 CFR 428.63 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.42 0.15 TSS 0.80 0.40 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.42 0.15 TSS 0.80 0.40 pH... Average of daily values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material...

7 CFR 58.517 - General.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Material § 58.517 General. Raw materials used for manufacturing cottage cheese shall meet the following quality...

7 CFR 58.517 - General.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Material § 58.517 General. Raw materials used for manufacturing cottage cheese shall meet the following quality...

40 CFR 122.23 - Concentrated animal feeding operations (applicable to State NPDES programs, see § 123.25).

Code of Federal Regulations, 2012 CFR

2012-07-01

... with any raw materials, products, or byproducts including manure, litter, feed, milk, eggs or bedding... manure handling system). (5) The term manure is defined to include manure, bedding, compost and raw... storage area, the raw materials storage area, and the waste containment areas. The animal confinement area...

40 CFR 122.23 - Concentrated animal feeding operations (applicable to State NPDES programs, see § 123.25).

Code of Federal Regulations, 2013 CFR

2013-07-01

... with any raw materials, products, or byproducts including manure, litter, feed, milk, eggs or bedding... manure handling system). (5) The term manure is defined to include manure, bedding, compost and raw... storage area, the raw materials storage area, and the waste containment areas. The animal confinement area...

40 CFR 122.23 - Concentrated animal feeding operations (applicable to State NPDES programs, see § 123.25).

Code of Federal Regulations, 2011 CFR

2011-07-01

... with any raw materials, products, or byproducts including manure, litter, feed, milk, eggs or bedding... manure handling system). (5) The term manure is defined to include manure, bedding, compost and raw... storage area, the raw materials storage area, and the waste containment areas. The animal confinement area...

40 CFR 122.23 - Concentrated animal feeding operations (applicable to State NPDES programs, see § 123.25).

Code of Federal Regulations, 2014 CFR

2014-07-01

... with any raw materials, products, or byproducts including manure, litter, feed, milk, eggs or bedding... manure handling system). (5) The term manure is defined to include manure, bedding, compost and raw... storage area, the raw materials storage area, and the waste containment areas. The animal confinement area...

Fabrication of Powder Metallurgy Pure Ti Material by Using Thermal Decomposition of TiH2

NASA Astrophysics Data System (ADS)

Mimoto, Takanori; Nakanishi, Nozomi; Umeda, Junko; Kondoh, Katsuyoshi

Titanium (Ti) and titanium alloys have been interested as an engineering material because they are widely used across various industrial applications, for example, motorcycle, automotive and aerospace industries, due to their light weight, high specific strength and superior corrosion resistance. Ti materials are particularly significant for the aircraft using carbon/carbon (C/C) composites, for example, carbon fiber reinforced plastics (CFRP), because Ti materials are free from the problem of contact corrosion between C/C composites. However, the applications of Ti materials are limited because of their high cost. From a viewpoint of cost reduction, cost effective process to fabricate Ti materials is strongly required. In the present study, the direct consolidation of titanium hydride (TiH2) raw powders in solid-state was employed to fabricate pure Ti bulk materials by using thermal decomposition of TiH2. In general, the production cost of Ti components is expensive due to using commercially pure (CP) Ti powders after dehydrogenation. On the other hand, the novel process using TiH2 powders as starting materials is a promising low cost approach for powder metallurgy (P/M) Ti products. Furthermore, this new process is also attractive from a viewpoint of energy saving because the dehydrogenation is integrated into the sintering process. In this study, TiH2 raw powders were directly consolidated by conventional press technique at 600 MPa to prepare TiH2 powder compacted billets. To thermally decompose TiH2 and obtain sintered pure Ti billets, the TiH2 powder billets were heated in the integrated sintering process including dehydrogenation. The hot-extruded pure Ti material, which was heat treated at 1273 K for 180 min in argon gas atmosphere, showed tensile strength of 701.8 MPa and elongation of 27.1%. These tensile properties satisfied the requirements for JIS Ti Grade 4. The relationship between microstructures, mechanical properties response and heat treatment temperature is discussed in detail.

Inorganic raw materials economy and provenance of chipped industry in some stone age sites of northern and central Italy.

PubMed

Bietti, Amilcare; Boschian, Giovanni; Crisci, Gino Mirocle; Danese, Ermanno; De Francesco, Anna Maria; Dini, Mario; Fontana, Federica; Giampietri, Alessandra; Grifoni, Renata; Guerreschi, Antonio; Liagre, Jérémie; Negrino, Fabio; Radi, Giovanna; Tozzi, Carlo; Tykot, Robert

2004-06-01

An opportunistic and local choice of raw materials is typically attested in the Lower and Middle Paleolithic industries throughout Italy. The quality of the raw material usually affected the flaking technology and quality of the products. In the Upper Paleolithic and the Mesolithic, raw material procurement strategies were more complex. Flint was exploited both locally, in areas where abundant outcrops of raw materials were available (such as the Lessini mountains), and in distant localities, after which it was transported or exchanged over medium/long distances. Different routes of exchange were thus followed in the various periods; good reconstruction of these routes have been provided by a study of the Garfagnana sites in Northern Tuscany, and the Mesolithic deposit of Mondeval de Sora (Dolomites). An interesting example of a Late Upper Paleolithic flint quarry and workshop were found in Abruzzo, in the San Bartolomeo shelter. The extended trade of obsidian from Lipari, Palmarola and Sardinia to the Italian Peninsula is attested in the Neolithic, with some differences concerning the age and different areas.

7 CFR 58.231 - General.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Materials § 58.231 General. All raw materials received at the drying plant shall meet the following quality...

7 CFR 58.231 - General.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Materials § 58.231 General. All raw materials received at the drying plant shall meet the following quality...

Synthesis of Rosin Acid Starch Catalyzed by Lipase

PubMed Central

Lin, Rihui; Li, He; Long, Han; Su, Jiating; Huang, Wenqin

2014-01-01

Rosin, an abundant raw material from pine trees, was used as a starting material directly for the synthesis of rosin acid starch. The esterification reaction was catalyzed by lipase (Novozym 435) under mild conditions. Based on single factor experimentation, the optimal esterification conditions were obtained as follows: rosin acid/anhydrous glucose unit in the molar ratio 2 : 1, reaction time 4 h at 45°C, and 15% of lipase dosage. The degree of substitution (DS) reaches 0.098. Product from esterification of cassava starch with rosin acid was confirmed by FTIR spectroscopy and iodine coloration analysis. Scanning electron microscopy and X-ray diffraction analysis showed that the morphology and crystallinity of the cassava starch were largely destroyed. Thermogravimetric analysis indicated that thermal stability of rosin acid starch decreased compared with native starch. PMID:24977156

21 CFR 113.81 - Product preparation.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Production and Process Controls § 113.81 Product preparation. (a) Before using raw materials and ingredients susceptible to microbiological contamination, the processor shall ensure that those materials and ingredients... by receiving the raw materials and ingredients under a supplier's guarantee that they are suitable...

Enhancement of efficiency of storage and processing of food raw materials using radiation technologies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gracheva, A. Yu.; Zav’yalov, M. A.; Ilyukhina, N. V.

The work is dedicated to improvement of efficiency of storage and processing of food raw materials using radiation technologies. International practice of radiation processing of food raw materials is presented and an increase in the consumption of irradiated food products is shown. The prospects of using radiation technologies for the processing of food products in Russia are discussed. The results of studies of radiation effects on various food products and packaging film by γ radiation and accelerated electrons are presented.

The Effect of Micro/Nano-metrics Size on the Interaction of Jordanian Aluminosilicate Raw Materials with High pH Solution

NASA Astrophysics Data System (ADS)

Aldabsheh, Islam; Garcia-Valles, Maite; Martinez, Salvador

2014-05-01

Environmental preservation has become a driving force behind the search for new sustainable and environmentally friendly composites to replace conventional concrete produced from ordinary Portland cement (OPC). Current researches concentrate on developing building products (geopolymers) through geopolymerization. The goal is to produce low cost construction materials for green housing. Geopolymerization is the process of polymerizing minerals with high silica and alumina at low temperature by the use of alkali solutions. Dissolution is the most important process for supplying the high initial Al and Si concentrations to produce the gel phase that is responsible for geopolymerization. This study has been focused on the influence of different micrometric particle sizes of three Jordanian raw materials on their dissolution behavior in sodium hydroxide solution. The samples are kaolinite, volcanic tuff and silica sand. The dissolution properties of each material, alone and mixed with the other two materials were studied in different concentrations (5 and 10 M) using (NaOH) at 25ºC, and shaking time for 24 and 168 h. To better understand the dissolution process, the alkaline solution was renewed after the desired time in order to know if the Al-Si raw material is completely dissolved or not. Different analytical techniques were used to characterize raw materials physically, mineralogically, chemically and thermally. All processed samples either centrifuged solutions or solid residues were fully characterized. The leached concentrations of Al and Si were determined by inductively coupled plasma (ICP). X-ray Diffraction Technique (XRD), Scanning Electron Microscopy (SEM), and Thermo Gravimetric Analysis (TGA) were used to evaluate the solid residue characterization compared with the original ones. The three aluminosilicate raw materials have indicated variable degrees of solubility under highly alkaline conditions. The method for the size reduction of the used raw materials achieved by using a ball mill increased the dissolution rate owing to the increased surface area of the material or particle exposed to the solvent. The used Jordanian raw materials are potential to be used for geopolymerization. This work was partly financed by SGR 2009SGR-00444

Material Characterization of Microsphere-Based Scaffolds with Encapsulated Raw Materials

PubMed Central

Sridharan, BanuPriya; Mohan, Neethu; Berkland, Cory J.; Detamore, Michael S.

2016-01-01

“Raw materials,” or materials capable of serving both as building blocks and as signals, which are often but not always natural materials, are taking center stage in biomaterials for contemporary regenerative medicine. In osteochondral tissue engineering, a field leveraging the underlying bone to facilitate cartilage regeneration, common raw materials include chondroitin sulfate (CS) for cartilage and β-tricalcium phosphate (TCP) for bone. Building on our previous work with gradient scaffolds based on microspheres, here we delved deeper into the characterization of individual components. In the current study, the release of CS and TCP from poly(D,L-lactic-co-glycolic acid) (PLGA) microsphere-based scaffolds was evaluated over a time period of 4 weeks. Raw material encapsulated groups were compared to ‘blank’ groups and evaluated for surface topology, molecular weight, and mechanical performance as a function of time. The CS group may have led to increased surface porosity, and the addition of CS improved the mechanical performance of the scaffold. The finding that CS was completely released into the surrounding media by 4 weeks has a significant impact on future in vivo studies, given rapid bioavailability. The addition of TCP seemed to contribute to the rough external appearance of the scaffold. The current study provides an introduction to degradation patterns of homogenous raw material encapsulated scaffolds, providing characterization data to advance the field of microsphere-based scaffolds in tissue engineering. PMID:27040236

Rapid bacteriological screening of cosmetic raw materials by using bioluminescence.

PubMed

Nielsen, P; Van Dellen, E

1989-01-01

Incoming cosmetic raw materials are routinely tested for microbial content. Standard plate count methods require up to 72 h. A rapid, sensitive, and inexpensive raw material screening method was developed that detects the presence of bacteria by means of ATP (bioluminescence). With a 24-h broth enrichment, the minimum bacterial ATP detection threshold of 1 cfu/g sample can be achieved using purified firefly luciferin-luciferase and an ATP releasing reagent. By using this rapid screen, microbiologically free material may be released for production within 24 h, while contaminated material undergoes further quantitative and identification testing. In order for a raw material to be validated for this method it must be evaluated for (1) a potential nonmicrobial light-contributing reaction resulting in a false positive or, (2) degradation of the ATP giving a false negative, and (3) confirmation that the raw material has not overwhelmed the buffering capacity of the enrichment broth. The key criteria for a rapid screen was the sensitivity to detect less than one colony forming unit per g product, the speed to do this within 24 h, and cost efficiency. Bioluminescence meets these criteria. With an enrichment step, it can detect less than one cfu/g sample. After the enrichment step, analysis time per sample is approximately 2 min and the cost for material and reagents is less than one dollar per sample.

31 CFR 545.413 - Importation of goods from third countries; transshipments.

Code of Federal Regulations, 2010 CFR

2010-07-01

...; transshipments. (a) Importation into the United States from third countries of goods containing raw materials or... raw materials or components have been incorporated into manufactured products or otherwise...

Effects of Starting Moisture on Characteristics of Oil Roasted Peanut

USDA-ARS?s Scientific Manuscript database

Previous research has shown that the moisture content of peanuts before dry roasting affects the quality of the finished product. This study demonstrates the effects of the starting moisture content of the raw product on peanuts that were oil roasted. Scanning Electron Microscope images taken befo...

Competitive Advantage Market Analysis | Energy Analysis | NREL

Science.gov Websites

Study An NREL market assessment of raw and intermediate materials, equipment, and products for equipment for c-Si PV Abundant raw materials for production of moisture barrier films, glass, aluminum

7 CFR 58.322 - Cream.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Material § 58... derived from raw material meeting the requirements as listed under §§ 58.132 through 58.138 of this...

7 CFR 58.322 - Cream.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Material § 58... derived from raw material meeting the requirements as listed under §§ 58.132 through 58.138 of this...

40 CFR 63.1251 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... ingredient means any material that is intended to furnish pharmacological activity or other direct effect in... this section. Consumption means the quantity of all HAP raw materials entering a process in excess of... as added as a raw material, consumption includes the quantity generated in the process. Container, as...

40 CFR 63.1251 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... ingredient means any material that is intended to furnish pharmacological activity or other direct effect in... this section. Consumption means the quantity of all HAP raw materials entering a process in excess of... as added as a raw material, consumption includes the quantity generated in the process. Container, as...

40 CFR 63.1251 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... ingredient means any material that is intended to furnish pharmacological activity or other direct effect in... this section. Consumption means the quantity of all HAP raw materials entering a process in excess of... as added as a raw material, consumption includes the quantity generated in the process. Container, as...

The properties of weft knitted fabric medical and preventive treatment action using eco-raw materials

NASA Astrophysics Data System (ADS)

Halavska, L.; Batrak, O.

2016-07-01

A new trend in the world is the clothing production using the new types of ecological raw materials application - milk, pineapple, coconut, hemp, banana, eucalyptus, clams, corn, bamboo, soya, nettle yarn. This makes it possible to create textile materials of new generation with unique antibacterial and antiseptic properties. Such materials have a positive preventive and sometimes therapeutic effect on people, and their health. Eco-raw materials clothing is able to protect the human body from the environment harmful effects: cold, heat, rain, dust, opportunely remove from underclothing layer the steam and gases, sweat; maintain in underclothing layer the necessary microclimate for normal organism functioning. Study of knitwear consumer properties, produced with eco-materials, is an urgent task of the world vector, directed on ecological environmental protection. This paper presents the research results of hygroscopicity and capillarity weft knitted fabrics, what knitted from different types of eco-raw materials: bamboo yarn, yarn containing soybean and nettle yarn. Character of influence of the liquid raising level changes depending on the experiment time and the knitting structure is revealed.

Influence of raw material properties upon critical quality attributes of continuously produced granules and tablets.

PubMed

Fonteyne, Margot; Wickström, Henrika; Peeters, Elisabeth; Vercruysse, Jurgen; Ehlers, Henrik; Peters, Björn-Hendrik; Remon, Jean Paul; Vervaet, Chris; Ketolainen, Jarkko; Sandler, Niklas; Rantanen, Jukka; Naelapää, Kaisa; De Beer, Thomas

2014-07-01

Continuous manufacturing gains more and more interest within the pharmaceutical industry. The International Conference of Harmonisation (ICH) states in its Q8 'Pharmaceutical Development' guideline that the manufacturer of pharmaceuticals should have an enhanced knowledge of the product performance over a range of raw material attributes, manufacturing process options and process parameters. This fits further into the Process Analytical Technology (PAT) and Quality by Design (QbD) framework. The present study evaluates the effect of variation in critical raw material properties on the critical quality attributes of granules and tablets, produced by a continuous from-powder-to-tablet wet granulation line. The granulation process parameters were kept constant to examine the differences in the end product quality caused by the variability of the raw materials properties only. Theophylline-Lactose-PVP (30-67.5-2.5%) was used as model formulation. Seven different grades of theophylline were granulated. Afterward, the obtained granules were tableted. Both the characteristics of granules and tablets were determined. The results show that differences in raw material properties both affect their processability and several critical quality attributes of the resulting granules and tablets. Copyright © 2014 Elsevier B.V. All rights reserved.

An integrated production-inventory model for food products adopting a general raw material procurement policy

NASA Astrophysics Data System (ADS)

Fauza, G.; Prasetyo, H.; Amanto, B. S.

2018-05-01

Studies on an integrated production-inventory model for deteriorating items have been done extensively. Most of the studies define deterioration as physical depletion of some inventories over time. This definition may not represent the deterioration characteristics of food products. The quality of food production decreases over time while the quantity remains the same. Further, in the existing models, the raw material is replenished several times (or at least once) within one production cycle. In food industries, however, a food company, for several reasons (e.g., the seasonal raw materials, discounted price, etc.) sometimes will get more benefit if it orders raw materials in a large quantity. Considering this fact, this research, therefore, is aimed at developing a more representative inventory model by (i) considering the quality losses in food and (ii) adopting a general raw material procurement policy. A mathematical model is established to represent the proposed policy in which the total profit of the system is the objective function. To evaluate the performance of the model, a numerical test was conducted. The numerical test indicates that the developed model has better performance, i.e., the total profit is 2.3% higher compared to the existing model.

The 1995 Medical Device Technology raw materials survey.

PubMed

Pearson, L S

1995-09-01

Using information supplied by manufacturers, this article reports on the use of raw materials and compounding and conversion practices in the European medical device manufacturing industry. The findings of the survey provide an indication of which materials are being used and how frequently, and the process of selecting suppliers.

Creating a Learning-Friendly Curriculum.

ERIC Educational Resources Information Center

Donovan, Michael P.

1997-01-01

Argues against a type of program evaluation of undergraduate institutions that assumes students are products. Proposes that if students are products, then students are raw materials. Discusses the philosophical problems of considering students as raw materials. (DDR)

60. INTERIOR VIEW OF THE RAW MATERIALS BUILDING, LOOKING AT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

60. INTERIOR VIEW OF THE RAW MATERIALS BUILDING, LOOKING AT THE POIDOMETER AND WEIGHING MACHINE. MAY 5, 1919. - United States Nitrate Plant No. 2, Reservation Road, Muscle Shoals, Muscle Shoals, Colbert County, AL

Satellite Relay Telemetry of Seismic Data in Earthquake Prediction and Control

NASA Technical Reports Server (NTRS)

Jackson, W. H.; Eaton, J. P.

1971-01-01

The Satellite Telemetry Earthquake Monitoring Program was started to evaluate the applicability of satellite relay telemetry in the collection of seismic data from a large number of dense seismograph clusters laid out along the major fault systems of western North America. Prototype clusters utilizing phone-line telemetry were then being installed by the National Center for Earthquake Research in 3 regions along the San Andreas fault in central California; and the experience of installing and operating the clusters and in reducing and analyzing the seismic data from them was to provide the raw materials for evaluation in the satellite relay telemetry project. The principal advantages of the satellite relay system over commercial telephone or microwave systems were: (1) it could be made less prone to massive failure during a major earthquake; (2) it could be extended readily into undeveloped regions; and (3) it could provide flexible, uniform communications over large sections of major global tectonic zones. Fundamental characteristics of a communications system to cope with the large volume of raw data collected by a short-period seismograph network are discussed.

Raw material procurement for termite fishing tools by wild chimpanzees in the Issa valley, Western Tanzania.

PubMed

Almeida-Warren, Katarina; Sommer, Volker; Piel, Alex K; Pascual-Garrido, Alejandra

2017-10-01

Chimpanzee termite fishing has been studied for decades, yet the selective processes preceding the manufacture of fishing tools remain largely unexplored. We investigate raw material selection and potential evidence of forward planning in the chimpanzees of Issa valley, western Tanzania. Using traditional archaeological methods, we surveyed the location of plants from where chimpanzees sourced raw material to manufacture termite fishing tools, relative to targeted mounds. We measured raw material abundance to test for availability and selection. Statistics included Chi-Squared, two-tailed Wilcoxon, and Kruskall-Wallace tests. Issa chimpanzees manufactured extraction tools only from bark, despite availability of other suitable materials (e.g., twigs), and selected particular plant species as raw material sources, which they often also exploit for food. Most plants were sourced 1-16 m away from the mound, with a maximum of 33 m. The line of sight from the targeted mound was obscured for a quarter of these plants. The exclusive use of bark tools despite availability of other suitable materials indicates a possible cultural preference. The fact that Issa chimpanzees select specific plant species and travel some distance to source them suggests some degree of selectivity and, potentially, forward planning. Our results have implications for the reconstruction of early hominin behaviors, particularly with regard to the use of perishable tools, which remain archaeologically invisible. © 2017 Wiley Periodicals, Inc.

Air electrode composition for solid oxide fuel cell

DOEpatents

Kuo, Lewis; Ruka, Roswell J.; Singhal, Subhash C.

1999-01-01

An air electrode composition for a solid oxide fuel cell is disclosed. The air electrode material is based on lanthanum manganite having a perovskite-like crystal structure ABO.sub.3. The A-site of the air electrode composition comprises a mixed lanthanide in combination with rare earth and alkaline earth dopants. The B-site of the composition comprises Mn in combination with dopants such as Mg, Al, Cr and Ni. The mixed lanthanide comprises La, Ce, Pr and, optionally, Nd. The rare earth A-site dopants preferably comprise La, Nd or a combination thereof, while the alkaline earth A-site dopant preferably comprises Ca. The use of a mixed lanthanide substantially reduces raw material costs in comparison with compositions made from high purity lanthanum starting materials. The amount of the A-site and B-site dopants is controlled in order to provide an air electrode composition having a coefficient of thermal expansion which closely matches that of the other components of the solid oxide fuel cell.

New woody and ambery notes from cedarwood and turpentine oil.

PubMed

Panten, Johannes; Bertram, Heinz-Jürgen; Surburg, Horst

2004-12-01

The development of a new product in the chemical industry is still driven by needs like technical properties, price/performance ratio, biodegradability, or product safety. However, in terms of improving more and more on ecological criteria, summarized under such catchphrases as sustainable development or green chemistry, another important aspect is to use renewable resources as starting materials. This is not significantly new in fragrance chemistry, and there are a lot of raw materials in the perfume oils that are derived from molecules of renewable resources. Two commonly used materials are: longifolene (from turpentine oil) and cedrene (from cedarwood oil). These compounds are very suitable for the synthesis of woody and ambery notes, and even though it seemed that all possibilities were exhausted, it is actually still feasible to discover new molecules with excellent olfactory properties such as Ambrocenide (50a), which is available in three steps from alpha-cedrene. Some of these molecules will be treated in this review, both with respect to synthesis as well as structural and sensory aspects.

Air electrode composition for solid oxide fuel cell

DOEpatents

Kuo, L.; Ruka, R.J.; Singhal, S.C.

1999-08-03

An air electrode composition for a solid oxide fuel cell is disclosed. The air electrode material is based on lanthanum manganite having a perovskite-like crystal structure ABO{sub 3}. The A-site of the air electrode composition comprises a mixed lanthanide in combination with rare earth and alkaline earth dopants. The B-site of the composition comprises Mn in combination with dopants such as Mg, Al, Cr and Ni. The mixed lanthanide comprises La, Ce, Pr and, optionally, Nd. The rare earth A-site dopants preferably comprise La, Nd or a combination thereof, while the alkaline earth A-site dopant preferably comprises Ca. The use of a mixed lanthanide substantially reduces raw material costs in comparison with compositions made from high purity lanthanum starting materials. The amount of the A-site and B-site dopants is controlled in order to provide an air electrode composition having a coefficient of thermal expansion which closely matches that of the other components of the solid oxide fuel cell. 3 figs.

Raw material variability of an active pharmaceutical ingredient and its relevance for processability in secondary continuous pharmaceutical manufacturing.

PubMed

Stauffer, F; Vanhoorne, V; Pilcer, G; Chavez, P-F; Rome, S; Schubert, M A; Aerts, L; De Beer, T

2018-06-01

Active Pharmaceutical Ingredients (API) raw material variability is not always thoroughly considered during pharmaceutical process development, mainly due to low quantities of drug substance available. However, synthesis, crystallization routes and production sites evolve during product development and product life cycle leading to changes in physical material attributes which can potentially affect their processability. Recent literature highlights the need for a global approach to understand the link between material synthesis, material variability, process and product quality. The study described in this article aims at explaining the raw material variability of an API using extensive material characterization on a restricted number of representative batches using multivariate data analysis. It is part of a larger investigation trying to link the API drug substance manufacturing process, the resulting physical API raw material attributes and the drug product continuous manufacturing process. Eight API batches produced using different synthetic routes, crystallization, drying, delumping processes and processing equipment were characterized, extensively. Seventeen properties from seven characterization techniques were retained for further analysis using Principal Component Analysis (PCA). Three principal components (PCs) were sufficient to explain 92.9% of the API raw material variability. The first PC was related to crystal length, agglomerate size and fraction, flowability and electrostatic charging. The second PC was driven by the span of the particle size distribution and the agglomerates strength. The third PC was related to surface energy. Additionally, the PCA allowed to summarize the API batch-to-batch variability in only three PCs which can be used in future drug product development studies to quantitatively evaluate the impact of the API raw material variability upon the drug product process. The approach described in this article could be applied to any other compound which is prone to batch-to-batch variability. Copyright © 2018 Elsevier B.V. All rights reserved.

Mercury Poisoning from an Unsuspected Source

PubMed Central

Tamir, M.; Bornstein, B.; Behar, M.; Chwat, M.

1964-01-01

In the manufacture of zinc oxide the raw material normally used in zinc metal plates. In a factory in which old aeroplane batteries containing zinc mercury amalgam were substituted, it was not realized that mercury vapour was being produced. Of 25 workers exposed, seven developed serious chronic mercury poisoning and were admitted to hospital. The clinical findings in the affected workers are described. They were first treated with penicillamine D, but in all but one case this had to be stopped because of rashes. Little improvement followed a switch to B.A.L. It is suggested that if penicillamine D is used in the treatment of mercury poisoning, steroid cover should be given from the start. PMID:14249900

Incentivizing secondary raw material markets for sustainable waste management.

PubMed

Schreck, Maximilian; Wagner, Jeffrey

2017-09-01

Notwithstanding several policy initiatives in many countries over a number of years, there remains a general sense that too much municipal solid waste is generated and that too much of the waste that is generated is landfilled. There is an emerging consensus that a sustainable approach to waste management requires further development of secondary raw material markets. The purpose of this paper is to propose a theoretical economic model that focuses upon this stage of a sustainable waste management program and explores policy options that could motivate efficiency in secondary raw material markets. In particular, we show how firm profit and social welfare optimizing objectives can be reconciled in a two-product market of waste management processes: landfilling and material reclamation. Our results provide theoretical support for building out recent Circular Economy initiatives as well as for the relatively recent emergence of landfill mining as a means for procuring secondary raw materials. Copyright © 2017 Elsevier Ltd. All rights reserved.

31 CFR 538.410 - Imports of Sudanese goods from third countries; transshipments.

Code of Federal Regulations, 2010 CFR

2010-07-01

...; transshipments. (a) Importation into the United States from third countries of goods containing raw materials or components of Sudanese origin is not prohibited if those raw materials or components have been incorporated...

78 FR 69132 - Importer of Controlled Substances; Notice of Registration; Noramco, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-18

... on applications to import narcotic raw material are not appropriate. 72 FR 3417(2007). In reference to the non-narcotic raw material, any bulk manufacturer who is presently, or is applying to be...

31 CFR 538.410 - Imports of Sudanese goods from third countries; transshipments.

Code of Federal Regulations, 2011 CFR

2011-07-01

...; transshipments. (a) Importation into the United States from third countries of goods containing raw materials or components of Sudanese origin is not prohibited if those raw materials or components have been incorporated...

78 FR 51747 - Importer of Controlled Substances; Notice of Application; NORAMCO, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-21

... on applications to import narcotic raw material are not appropriate. 72 FR 3417 (2007). In reference to the non-narcotic raw material, any bulk manufacturer who is presently, or is applying to be...

The U.S. Chemical Industry, the Raw Materials It Uses

ERIC Educational Resources Information Center

Chemical and Engineering News, 1972

1972-01-01

The raw materials used by the industry are considered in this section of the annual chemical industry report, including data covering: natural gas, lead, mercury, phosphate rock, potash, salt, petroleum products including petrochemical feedstocks. (PR)

Cellulose acetate fibers prepared from different raw materials with rapid synthesis method.

PubMed

Chen, Jinghuan; Xu, Jikun; Wang, Kun; Cao, Xuefei; Sun, Runcang

2016-02-10

Transesterification is a mild process to prepare cellulose acetate (CA) as compared with the traditional method. In this study, CA fibers were produced from six cellulose raw materials based on a simple and rapid transesterification method. The properties of the CA solutions and the obtained CA fibers were investigated in detail. Results showed that all of the cellulose raw materials were esterified within 15 min, and spinning dopes could be obtained by concentrating the CA solutions via vacuum distillation. The XRD, FT-IR, (1)H, (13)C and HSQC NMR analysis confirmed the successful synthesis of CA. The degree of substitution (DS) of the obtained CA was significantly affected by the degree of polymerization (DP) of cellulose raw materials, which further influenced the viscosity of CA solutions as well as the structural, thermal and mechanical properties of the CA fibers. Copyright © 2015 Elsevier Ltd. All rights reserved.

Method of fabricating a honeycomb structure

DOEpatents

Holleran, Louis M.; Lipp, G. Daniel

1999-01-01

A method of fabricating a monolithic honeycomb structure product involves shaping a first mixture of raw materials and a binder into a green honeycomb, extruding a second mixture of raw materials and a binder into one or more green members that each define an opening extending longitudinally therethrough. The raw materials of the second mixture are compatible with the raw materials of the first mixture. The green honeycomb and member(s) are dried. The binders of the green honeycomb and member(s) are softened at the surfaces that are to be bonded. The green member(s) is inserted into the honeycomb and bonded to the honeycomb to form an assembly thereof, which is then dried and fired to form a unified monolithic honeycomb structure. The insertion is best carried out by mounting a member in the shape of a tube on a mandrel, and inserting the mandrel into the honeycomb opening to bond the tube to the honeycomb.

Method of fabricating a honeycomb structure

DOEpatents

Holleran, L.M.; Lipp, G.D.

1999-08-03

A method of fabricating a monolithic honeycomb structure product involves shaping a first mixture of raw materials and a binder into a green honeycomb, extruding a second mixture of raw materials and a binder into one or more green members that each define an opening extending longitudinally therethrough. The raw materials of the second mixture are compatible with the raw materials of the first mixture. The green honeycomb and member(s) are dried. The binders of the green honeycomb and member(s) are softened at the surfaces that are to be bonded. The green member(s) is inserted into the honeycomb and bonded to the honeycomb to form an assembly thereof, which is then dried and fired to form a unified monolithic honeycomb structure. The insertion is best carried out by mounting a member in the shape of a tube on a mandrel, and inserting the mandrel into the honeycomb opening to bond the tube to the honeycomb. 7 figs.

Theoretical backgrounds of non-tempered materials production based on new raw materials

NASA Astrophysics Data System (ADS)

Lesovik, V. S.; Volodchenko, A. A.; Glagolev, E. S.; Chernysheva, N. V.; Lashina, I. V.; Feduk, R. S.

2018-03-01

One of the trends in construction material science is development and implementation of highly effective finish materials which improve architectural exterior of cities. Silicate materials widely-used in the construction today have rather low decorative properties. Different coloring agents are used in order to produce competitive materials, but due to the peculiarities of the production, process very strict specifications are applied to them. The use of industrial wastes or variety of rock materials as coloring agents is of great interest nowadays. The article shows that clay rock can be used as raw material in production of finish materials of non-autoclaved solidification. This raw material due to its material composition actively interacts with cementing component in steam treatment at 90–95 °C with formation of cementing joints that form a firm coagulative-cristalized and crystallization structure of material providing high physic-mechanical properties of silicate goods. It is determined that energy-saving, colored finish materials with compression strength up to 16 MPa can be produced from clay rocks.

40 CFR 63.1345 - Emissions limits for affected sources other than kilns; in-line kiln/raw mills; clinker coolers...

Code of Federal Regulations, 2011 CFR

2011-07-01

... other than kilns; in-line kiln/raw mills; clinker coolers; new and reconstructed raw material dryers; and raw and finish mills, and open clinker piles. 63.1345 Section 63.1345 Protection of Environment... for affected sources other than kilns; in-line kiln/raw mills; clinker coolers; new and reconstructed...

Development of Product Availability Monitoring System In Production Unit In Automotive Component Industry

NASA Astrophysics Data System (ADS)

Hartono, Rachmad; Raharno, Sri; Yuwana Martawirya, Yatna; Arthaya, Bagus

2018-03-01

This paper described a methodology to monitor the availability of products in a production unit in the automotive component industry. Automotive components made are automotive components made through sheet metal working. Raw material coming into production unit in the form of pieces of plates that have a certain size. Raw materials that come stored in the warehouse. Data of raw each material in the warehouse are recorded and stored in a data base system. The material will then undergo several production processes in the production unit. When the material is taken from the warehouse, material data are also recorded and stored in a data base. The data recorded are the amount of material, material type, and date when the material is out of the warehouse. The material coming out of the warehouse is labeled with information related to the production processes that the material must pass. Material out of the warehouse is a product will be made. The products have been completed, are stored in the warehouse products. When the product is entered into the product warehouse, product data is also recorded by scanning the barcode contained on the label. By recording the condition of the product at each stage of production, we can know the availability of the product in a production unit in the form of a raw material, the product being processed and the finished product.

Needs assessment for nondestructive testing and materials characterization for improved reliability in structural ceramics for heat engines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, D.R.; McClung, R.W.; Janney, M.A.

1987-08-01

A needs assessment was performed for nondestructive testing and materials characterization to achieve improved reliability in ceramic materials for heat engine applications. Raw materials, green state bodies, and sintered ceramics were considered. The overall approach taken to improve reliability of structural ceramics requires key inspections throughout the fabrication flowsheet, including raw materials, greed state, and dense parts. The applications of nondestructive inspection and characterization techniques to ceramic powders and other raw materials, green ceramics, and sintered ceramics are discussed. The current state of inspection technology is reviewed for all identified attributes and stages of a generalized flowsheet for advanced structuralmore » ceramics, and research and development requirements are identified and listed in priority order. 164 refs., 3 figs.« less

75 FR 65658 - Importer of Controlled Substances; Notice of Application

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-26

... Raw Opium (9600) II Concentrate of Poppy Straw (9670) II The company plans to import narcotic raw... a manufacturer of several controlled substances that are manufactured from raw opium, poppy straw... narcotic raw material are not appropriate. As noted in a previous notice published in the Federal Register...

7 CFR 58.519 - Dairy products.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Specifications for Dairy Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Material § 58.519 Dairy products. (a) Raw skim milk. All raw skim milk obtained from a secondary source... used, shall be prepared from raw milk or skim milk that meets the same quality requirements outlined...

Hardwood pallet cant quality and pallet part yields

Treesearch

Hal L. Mitchell; Marshall White; Philip Araman; Peter Hamner

2005-01-01

Raw materials are the largest cost component in pallet manufacturing. The primary raw material used to produce pallet parts are pallet cants. Therefore, pallet cant quality directly impacts pallet part processing and material costs. By knowing the quality of the cants being processed, pallet manufacturers can predict these costs and improve manufacturing efficiency....

Methodology for the Assessment of the Ecotoxicological Potential of Construction Materials

PubMed Central

Rodrigues, Patrícia; Silvestre, José D.; Flores-Colen, Inês; Viegas, Cristina A.; de Brito, Jorge; Kurad, Rawaz; Demertzi, Martha

2017-01-01

Innovation in construction materials (CM) implies changing their composition by incorporating raw materials, usually non-traditional ones, which confer the desired characteristics. However, this practice may have unknown risks. This paper discusses the ecotoxicological potential associated with raw and construction materials, and proposes and applies a methodology for the assessment of their ecotoxicological potential. This methodology is based on existing laws, such as Regulation (European Commission) No. 1907/2006 (REACH—Registration, Evaluation, Authorization and Restriction of Chemicals) and Regulation (European Commission) No. 1272/2008 (CLP—Classification, Labelling and Packaging). Its application and validation showed that raw material without clear evidence of ecotoxicological potential, but with some ability to release chemicals, can lead to the formulation of a CM with a slightly lower hazardousness in terms of chemical characterization despite a slightly higher ecotoxicological potential than the raw materials. The proposed methodology can be a useful tool for the development and manufacturing of products and the design choice of the most appropriate CM, aiming at the reduction of their environmental impact and contributing to construction sustainability. PMID:28773011

Preparation of SiC/SiO2 core-shell nanowires via molten salt mediated carbothermal reduction route

NASA Astrophysics Data System (ADS)

Zhang, Ju; Yan, Shuai; Jia, Quanli; Huang, Juntong; Lin, Liangxu; Zhang, Shaowei

2016-06-01

The growth of silicon carbide (SiC) crystal generally requires a high temperature, especially when low quality industrial wastes are used as the starting raw materials. In this work, SiC/SiO2 core-shell nanowires (NWs) were synthesized from low cost silica fume and sucrose via a molten salt mediated carbothermal reduction (CR) route. The molten salt was found to be effective in promoting the SiC growth and lowering the synthesis temperature. The resultant NWs exhibited a heterostructure composed of a 3C-SiC core of 100 nm in diameter and a 5-10 nm thick amorphous SiO2 shell layer. The photoluminescence spectrum of the achieved SiC NWs displayed a significant blue shift (a dominant luminescence at round 422 nm), which suggested that they were high quality and could be a promising candidate material for future optoelectronic applications.

77 FR 73426 - Glycine From the People's Republic of China: Final Partial Affirmative Determination of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-10

... the Order because it is producing glycine from raw materials of Indian origin and exporting such... Order because it produced glycine from raw materials of Indian origin and exported such merchandise to...

Critical thinking: assessing the risks to the future security of supply of critical metals

NASA Astrophysics Data System (ADS)

Gunn, Gus

2015-04-01

Increasing world population, the spread of prosperity across the globe and the demands of new technologies have led to a revival of concerns about the availability of raw materials needed by society. Despite scare stories about resource depletion, physical exhaustion of minerals is considered to be unlikely. However, we do need to know which materials might be of concern so that we can develop strategies to secure adequate supplies and to mitigate the effects of supply disruption. This requirement has led to renewed interest in criticality, a term that is generally used to refer to metals and minerals of high economic importance that have a relatively high likelihood of supply disruption. The European Union (EU) developed a quantitative methodology for the assessment of criticality which led to the definition of 14 raw materials as critical to the EU economy (EC, 2010). This has succeeded in raising awareness of potential supply issues and in helping to prioritise requirements for new policies and supporting research. The EU has recently assessed a larger number of candidate materials of which 20 are now identified as critical to the EU (EC, 2014). These include metals such as indium, mostly used in flat-screen displays, antimony for flame retardants and cobalt for rechargeable batteries, alloys and a host of other products. Although there is no consensus on the methodology for criticality assessments and broad analyses at this scale are inevitably imperfect, they can, nevertheless, provide early warning of supply problems. However, in order to develop more rigorous and dynamic assessments of future availability detailed analysis of the whole life-cycle of individual metals to identify specific problems and develop appropriate solutions is required. New policies, such as the Raw Materials Initiative (2008) and the European Innovation Partnership on Raw Materials (2013), have been developed by the European Commission (EC) and are aimed at securing sustainable supplies of raw materials. These have led to major new programmes of research throughout the minerals value chain, in order to improve the raw materials knowledge base, to develop best practices and promote international collaboration. Although recycling will make an increasingly important contribution to supply, it can never meet the total requirement when demand is increasing. Therefore, new resources of primary materials, identified through geological research, will continue to be required. The availability of regional baseline datasets, comprising geological, geophysical and geochemical data, is fundamental to the identification of exploration targets. However, in order to focus exploration we also require robust mineral deposit models for the critical metals which hitherto these have been largely neglected because of their limited economic importance. For commodities such as the platinum-group metals (PGM), cobalt, niobium, indium, rare earth elements (REE) and cobalt we have some knowledge of the processes controlling their mobilisation and concentration under certain conditions although we have little understanding of the mechanisms of deposit formation elsewhere. We also need effective techniques to explore for these metals. This may involve the development of new geophysical techniques to explore on the sea-floor or beneath thick cover, or new analytical methods for the determination of these elements in exploration samples. Improved metallurgical techniques are also required for effective and energy-efficient recovery of critical metals from ores and concentrates. References European Commission (2010). Critical raw materials for the EU. Report of the Ad-hoc Working Group on Defining Critical Raw Materials. European Commission (2014). Report on Critical raw materials for the EU. Report of the Ad-hoc Working Group on Defining Critical Raw Materials.

Influence of roll levelling on material properties and postforming springback

NASA Astrophysics Data System (ADS)

Galdos, Lander; Mendiguren, Joseba; de Argandoña, Eneko Saenz; Otegi, Nagore; Silvestre, Elena

2018-05-01

Roll levelling is commonly used in cut to length and blanking lines to flatten initial coils and produce residual stress free precuts. Roll straightener is also used to remove coil-set when progressive dies are used and the starting raw material is a coil. Industrial evidences have proved that roll leveler or straightener tuning is crucial to get a robust process and to obtain repetitive springback values after stamping. This is more relevant when using Advanced High Strength Steels and aluminum coils. However, the mechanisms affecting this material behavior are unknown and how the levelling technology affects the material properties has not been yet reported. In this paper, the influence the roll levelling process has on the final properties of a 6xxx aluminum alloy is studied. For that, as received coils have been relevelled using two different leveler set-ups and tensile tests have been performed using both initial and final material states. Aiming to quantify the effect of the material hardening on a real forming process, a new tangential bending prototype has been developed. As received and levelled precuts have been bent and the forming torques and the postforming angles have been compared.

77 FR 34069 - Importer of Controlled Substances; Notice of Application; Research Triangle Institute

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-08

... activities. Comments and requests for hearings on applications to import narcotic raw material are not appropriate. 72 FR 3417 (2007). In regard to the non-narcotic raw material, any bulk manufacturer who is... [[Page 34072

Evaluation of physicochemical properties as supporting information on quality control of raw materials and veterinary pharmaceutical formulations.

PubMed

Anacleto, Sara da Silva; Borges, Marcella Matos Cordeiro; de Oliveira, Hanna Leijoto; Vicente, Andressa Reis; de Figueiredo, Eduardo Costa; de Oliveira, Marcone Augusto Leal; Borges, Bárbara Juliana Pinheiro; de Oliveira, Marcelo Antonio; Borges, Warley de Souza; Borges, Keyller Bastos

2018-06-01

This study aimed to show that the physicochemical proprieties obtained by Fourier transform infrared spectroscopy (FTIR), thermogravimetry (TG), and scanning electronic microscopy (SEM) can be useful tools for evaluating the quality of active pharmaceutical ingredients (APIs) and pharmaceutical products. In addition, a simple, sensitive, and efficient method employing HPLC-DAD was developed for simultaneous determination of lidocaine (LID), ciprofloxacin (CFX) and enrofloxacin (EFX) in raw materials and in veterinary pharmaceutical formulations. Compounds were separated using a Gemini C 18 (250 mm × 4.6 mm, 5 µm) Phenomenex ® column, at a temperature of 25 °C, with a mobile phase containing 10 mM of phosphoric acid (pH 3.29): acetonitrile (85.7:14.3, v/v) and a flow rate of 1.5 mL/min. Physicochemical characterization by TG, FTIR, and SEM of raw materials of LID, CFX, and EFX provided information useful for the evaluation, differentiation, and qualification of raw materials. Finally, the HPLC method was proved to be useful for evaluation of raw material and finished products, besides satisfying the need for an analytical method that allows simultaneous determination of EFX, CFX, and LID, which can also be extended to other matrices and applications.

Colour of ground beef as influenced by raw materials, addition of sodium chloride and low oxygen packaging.

PubMed

Sørheim, O; Westad, F; Larsen, H; Alvseike, O

2009-03-01

The study aimed at examining the effects of freezing of raw materials, holding time for fresh raw materials post mortem and addition of 0.5-1.0% NaCl on the colour of ground beef under low oxygen (O2) modified atmosphere storage. The samples were exposed to 0.1-3.0% O2 at 4°C for up to 10 days, and analysed for O2 concentrations, instrumental and visual colour. Residual O2 in the headspace of the packages oxidizes myoglobin and discolours the meat. Meat may have the ability to scavenge residual O2, and ground beef differs from intact muscles by having a much higher capacity for O2 consumption. In this experiment, the use of frozen/thawed raw materials and addition of NaCl both decreased the rate of O2 consumption and increased discolouration. Using raw materials from 2 days rather than 7 days post mortem greatly increased the rate of removal of O2 and improved redness. In low O2 packaging, ground beef preferably should be stored for at least 2 days in an atmosphere with less than 0.1% residual O2 to produce a purple pigment predominantly consisting of deoxymyoglobin.

Effects and detection of raw material variability on the performance of near-infrared calibration models for pharmaceutical products.

PubMed

Igne, Benoit; Shi, Zhenqi; Drennen, James K; Anderson, Carl A

2014-02-01

The impact of raw material variability on the prediction ability of a near-infrared calibration model was studied. Calibrations, developed from a quaternary mixture design comprising theophylline anhydrous, lactose monohydrate, microcrystalline cellulose, and soluble starch, were challenged by intentional variation of raw material properties. A design with two theophylline physical forms, three lactose particle sizes, and two starch manufacturers was created to test model robustness. Further challenges to the models were accomplished through environmental conditions. Along with full-spectrum partial least squares (PLS) modeling, variable selection by dynamic backward PLS and genetic algorithms was utilized in an effort to mitigate the effects of raw material variability. In addition to evaluating models based on their prediction statistics, prediction residuals were analyzed by analyses of variance and model diagnostics (Hotelling's T(2) and Q residuals). Full-spectrum models were significantly affected by lactose particle size. Models developed by selecting variables gave lower prediction errors and proved to be a good approach to limit the effect of changing raw material characteristics. Hotelling's T(2) and Q residuals provided valuable information that was not detectable when studying only prediction trends. Diagnostic statistics were demonstrated to be critical in the appropriate interpretation of the prediction of quality parameters. © 2013 Wiley Periodicals, Inc. and the American Pharmacists Association.

Materials, critical materials and clean-energy technologies

NASA Astrophysics Data System (ADS)

Eggert, R.

2017-07-01

Modern engineered materials, components and systems depend on raw materials whose properties provide essential functionality to these technologies. Some of these raw materials are subject to supply-chain risks, and such materials are known as critical materials. This paper reviews corporate, national and world perspectives on material criticality. It then narrows its focus to studies that assess "what is critical" to clean-energy technologies. The focus on supply-chain risks is not meant to be alarmist but rather to encourage attention to monitoring these risks and pursuing technological innovation to mitigate the risks.

Raw liquid waste treatment process

NASA Technical Reports Server (NTRS)

Humphrey, Marshall F. (Inventor)

1980-01-01

A raw sewage treatment process is disclosed in which substantially all the non-dissolved matter, which is suspended in the sewage water is first separated from the water, in which at least organic matter is dissolved. The non-dissolved material is pyrolyzed to form an activated carbon and ash material without the addition of any conditioning agents. The activated carbon and ash material is added to the water from which the non-dissolved matter was removed. The activated carbon and ash material absorbs organic matter and heavy metal ions, it is believed, are dissolved in the water and is thereafter supplied in a counter current flow direction and combined with the incoming raw sewage to facilitate the separation of the non-dissolved settleable materials from the sewage water. The used carbon and ash material together with the non-dissolved matter which was separated from the sewage water are pyrolyzed to form the activated carbon and ash material.

Raw Liquid Waste Treatment System and Process

NASA Technical Reports Server (NTRS)

Humphrey, M. F. (Inventor)

1974-01-01

A raw sewage treatment process is disclosed in which substantially all the non-dissolved matter, suspended in the sewage water is first separated from the water, in which at least organic matter remains dissolved. The non-dissolved material is pyrolyzed to form an activated carbon and ash material without the addition of any conditioning agents. The activated carbon and ash material is added to the water from which the non-dissolved matter was removed. The activated carbon and ash material adsorbs the organic matter dissolved in the water and is thereafter supplied in a counter flow direction and combined with the incoming raw sewage to at least facilitate the separation of the non-dissolved settleable materials from the sewage water. Carbon and ash material together with the non-dissolved matter which was separated from the sewage water are pyrolyzed to form the activated carbon and ash material.

Environmental analysis of the life cycle emissions of 2-methyl tetrahydrofuran solvent manufactured from renewable resources.

PubMed

Slater, C Stewart; Savelski, Mariano J; Hitchcock, David; Cavanagh, Eduardo J

2016-01-01

An environmental analysis has been conducted to determine the cradle to gate life cycle emissions to manufacture the green solvent, 2-methyl tetrahydrofuran. The solvent is considered a greener chemical since it can be manufactured from renewable resources with a lower life cycle footprint. Analyses have been performed using different methods to show greenness in both its production and industrial use. This solvent can potentially be substituted for other ether and chlorinated solvents commonly used in organometallic and biphasic reactions steps in pharmaceutical and fine chemical syntheses. The 2-methyl tetrahydrofuran made from renewable agricultural by-products is marketed by Penn A Kem under the name ecoMeTHF™. The starting material, 2-furfuraldehyde (furfural), is produced from corn cob waste by converting the available pentosans by acid hydrolysis. An evaluation of each step in the process was necessary to determine the overall life cycle and specific CO2 emissions for each raw material/intermediate produced. Allocation of credits for CO2 from the incineration of solvents made from renewable feedstocks significantly reduced the overall carbon footprint. Using this approach, the overall life cycle emissions for production of 1 kg of ecoMeTHF™ were determined to be 0.191 kg, including 0.150 kg of CO2. Life cycle emissions generated from raw material manufacture represents the majority of the overall environmental impact. Our evaluation shows that using 2-methyl tetrahydrofuran in an industrial scenario results in a 97% reduction in emissions, when compared to typically used solvents such as tetrahydrofuran, made through a conventional chemical route.

21 CFR 1303.23 - Procedure for fixing individual manufacturing quotas.

Code of Federal Regulations, 2010 CFR

2010-04-01

... economic and physical availability of raw materials for use in manufacturing and for inventory purposes, yield and stability problems, potential disruptions to production (including possible labor strikes... current inventory position, the economic and physical availability of raw materials for use in...

Use of outer planet satellites and asteroids as sources of raw materials for life support systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Molton, P.M.; Divine, T.E.

1977-01-01

Industrialization of space and other space activities depend entirely on supply of materials from the Earth. This is a high cost route for materials supply. Space industrialization will require life support systems for maintenance and operation staff and these will of necessity be of a sophisticated nature. Use of raw materials obtained by an unmanned space shuttle, initially, and by manned shuttles later could significantly reduce the cost of life support in space. These raw materials could be obtained from small asteroids and satellites, and would consist of primary nutrients. Future development of such sources is discussed, including food productionmore » in automated asteroid-based facilities. The level of technology required is available now, and should become economical within a century.« less

Rambutan Seed (Nephelium Lappaceum L.) Optimization as Raw Material of High Nutrition Value Processed Food

NASA Astrophysics Data System (ADS)

Wahini, M.; Miranti, M. G.; Lukitasari, F.; Novela, L.

2018-02-01

Rambutan (Nephelium Lappaceum L.) is a plant that identical with Southeast Asian countries, in some areas of Indonesia no exception, but rambutan seed is considered as a waste. Therefore, it needs to be optimized into raw materials of food and processed with high nutritional value and has economic value. The purpose of this research were: 1) to find the best rambutan seed immersion formula; 2) to know the nutritional value of the best immersed rambutan seed; 3) to produce raw material and various processed of rambutan seed product. The research method was quasi experiment with 6 treatments and 2 factorial design, materials for immersion was NaCl and Ca(OH)2. The results showed that: 1) the best rambutan seed immersion formula was using Ca(OH)2; 2) the best rambutan seed contains 1,6 ash, 31,2 protein, 26,9 fat; 3) the best rambutan seed produce flour and processed of seasoned nuts. This research indicates that rambutan seed is very potential to be an alternative high-value raw materials.

21 CFR 1315.23 - Procedure for fixing individual manufacturing quotas.

Code of Federal Regulations, 2010 CFR

2010-04-01

...) The economic and physical availability of raw materials for use in manufacturing and for inventory purposes, (iv) Yield and stability problems, (v) Potential disruptions to production (including possible... cycle and current inventory position. (iii) The economic and physical availability of raw materials for...

40 CFR 63.1251 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... other direct effect in the diagnosis, cure, mitigation, treatment, or prevention of disease, or to... this section. Consumption means the quantity of all HAP raw materials entering a process in excess of... as added as a raw material, consumption includes the quantity generated in the process. Container, as...

40 CFR 63.1251 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... other direct effect in the diagnosis, cure, mitigation, treatment, or prevention of disease, or to... this section. Consumption means the quantity of all HAP raw materials entering a process in excess of... as added as a raw material, consumption includes the quantity generated in the process. Container, as...

VIEW ALONG RAW MATERIAL CONVEYOR AT RIGHT WITH CRUSHED SHELL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

VIEW ALONG RAW MATERIAL CONVEYOR AT RIGHT WITH CRUSHED SHELL CONVEYOR ABOVE. ENGINE AND RADIATOR AT LOWER LEFT. - F. & H. Benning Company Oyster Mill, 14430 Solomons Island Road (moved from 1014 Benning Road, Galesville, Anne Arundel County, Maryland), Solomons, Calvert County, MD

40 CFR 415.91 - Specialized definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... of any raw material, intermediate product, finished product, by-product, or waste product. The term... contact with any raw material, intermediate product, finished product, by-product or waste product by... this subpart. (b) The term product shall mean hydrogen peroxide as a one hundred percent hydrogen...

Aluminium content of some processed foods, raw materials and food additives in China by inductively coupled plasma-mass spectrometry.

PubMed

Deng, Gui-Fang; Li, Ke; Ma, Jing; Liu, Fen; Dai, Jing-Jing; Li, Hua-Bin

2011-01-01

The level of aluminium in 178 processed food samples from Shenzhen city in China was evaluated using inductively coupled plasma-mass spectrometry. Some processed foods contained a concentration of up to 1226 mg/kg, which is about 12 times the Chinese food standard. To establish the main source in these foods, Al levels in the raw materials were determined. However, aluminium concentrations in raw materials were low (0.10-451.5 mg/kg). Therefore, aluminium levels in food additives used in these foods was determined and it was found that some food additives contained a high concentration of aluminium (0.005-57.4 g/kg). The results suggested that, in the interest of public health, food additives containing high concentrations of aluminium should be replaced by those containing less. This study has provided new information on aluminium levels in Chinese processed foods, raw materials and a selection of food additives.

Raw materials exploitation in Prehistory of Georgia: sourcing, processing and distribution

NASA Astrophysics Data System (ADS)

Tushabramishvili, Nikoloz; Oqrostsvaridze, Avthandil

2016-04-01

Study of raw materials has a big importance to understand the ecology, cognition, behavior, technology, culture of the Paleolithic human populations. Unfortunately, explorations of the sourcing, processing and distribution of stone raw materials had a less attention until the present days. The reasons of that were: incomplete knowledge of the archaeologists who are doing the late period archaeology (Bronze Age-Medieval) and who are little bit far from the Paleolithic technology and typology; Ignorance of the stone artifacts made on different kind of raw-materials, except flint and obsidians. Studies on the origin of the stone raw materials are becoming increasingly important since in our days. Interesting picture and situation have been detected on the different sites and in different regions of Georgia. In earlier stages of Middle Paleolithic of Djruchula Basin caves the number of basalt, andesite, argillite etc. raw materials are quite big. Since 130 000 a percent of the flint raw-material is increasing dramatically. Flint is an almost lonely dominated raw-material in Western Georgia during thousand years. Since approximately 50 000 ago the first obsidians brought from the South Georgia, appeared in Western Georgia. Similar situation has been detected by us in Eastern Georgia during our excavations of Ziari and Pkhoveli open-air sites. The early Lower Paleolithic layers are extremely rich by limestone artifacts while the flint raw-materials are dominated in the Middle Paleolithic layers. Study of these issues is possible to achieve across chronologies, the origins of the sources of raw-materials, the sites and regions. By merging archaeology with anthropology, geology and geography we are able to acquire outstanding insights about those populations. New approach to the Paleolithic stone materials, newly found Paleolithic quarries gave us an opportunities to try to achieve some results for understanding of the behavior of Paleolithic populations, geology and geomorphology of different regions of Georgia. References: 1. 2015. Tushabramishvili N. Ziari. Online Archaeology 8. Tbilisi, Georgia. Pp. 41-43 2. 2012. M François-Xavier Le Bourdonnec, Sébastien Nomade, Gérard Poupeau, Hervé Guillou, Nikolos Tushabramishvili, Marie-Hélène Moncel, David Pleurdeau, Tamar Agapishvili, Pierre Voinchet, Ana Mgeladze, David Lordkipanidze). Multiple origins of Bondi Cave and Ortvale Klde (NW Georgia) obsidians and human mobility in Transcaucasia during the Middle and Upper Palaeolithic. Journal of Archaeological Science xxx (2012) 1-14 3. 2011. Mercier N., Valladas H., Meignen L., Joron J. L., Tushabramishvili N., Adler D.S., Bar Yosef O. Dating the early Middle Palaeolithic Laminar Industry from Djruchula cave, Republic of Georgia. Paléorient Volume 36. Issue 36-2, pp. 163-173 4. 2010. L. Meignen&Nicholas Tushabramishvili. Djruchula Cave, on the Southern Slopes of the Great Caucasus: An Extension of the Near Eastern Middle Paleolithic Blady Phenomenon to the North. Journal of The Israel Prehistoric Society 40 (2010), 35-61 5. 2007. Tushabramishvili N.,Pleurdeau D., Moncel M.-H., Mgeladze A. Le complexe Djruchula-Koudaro au sud Caucase (Géorgie). Remarques sur les assemblages lithiques pléistocenes de Koudaro I, Tsona et Djruchula . Anthropologie • 45/1 • pp. 1-18 6. Tushabramishvili, D., 1984. Paleolit Gruzii. (Palaeolithic of Georgia). Newsletter of the Georgian State Museum 37B, 5e27

Alternative of raw material’s suppliers using TOPSIS method in chicken slaughterhouse industry

NASA Astrophysics Data System (ADS)

Sari, R. M.; Rizkya, I.; Syahputri, K.; Anizar; Siregar, I.

2018-02-01

Chicken slaughterhouse industry is one of the fastest growing industries that depends on the freshness of raw materials. The raw materials quality arrive at the company depends heavily on the suppliers. Fresh chicken and frozen chicken meat are the main raw materials for this industry. Problems occurred by the suppliers are catering the amount of raw material needs that are not appropriate and also delay during delivery process. This condition causes disruption of the production process in the company. Therefore, it is necessary to determine the best suppliers to supply the main raw materials of fresh and frozen chicken meat on the slaughterhouse chicken industry. This study analyze the supplier’s capability by using TOPSIS method. This method use to find out the best supplier. The TOPSIS method is performed using the principle that chosen alternative must have the shortest distance from the positive solution and furthest from the ideal solution of the geometric point by using the Euclidean distance to determine the relative proximity of the optimum solution alternative. TOPSIS method found the rank of best supplier’s order is supplier A followed by supplier D, supplier B, supplier C, supplier E, supplier F, and supplier G. Based on the rank order obtained from each company, it will assist the company in prioritizing the order to the supplier with the best rank. Total supply from All suppliers are 885,994 kg per month. Based on the results of research, the top five suppliers have been sufficient to meet the needs of the company.

Development of an Assessment Method for Building Materials Under Euratom Scope.

PubMed

de With, Govert

2017-11-01

In 2013, the European Commission published its basic safety standards for protection against the dangers arising from exposure to ionizing radiation (Council Directive 2013/59/Euratom)-also known as EU-BSS. As a result, the use of raw materials with potentially elevated activity concentrations such as fly ash, phosphogypsum, and slags will now fall under EU-BSS scope when applied in building materials. In light of this new policy, a variety of tools are available to assess compliance with the 1-mSv y reference level for building materials. At the heart of these tools is a gamma-spectrometric determination of the naturally occurring radionuclides Ra, Th, and K in the material of concern. As a large number of construction products contain a certain amount of the raw material that falls under the scope of the EU regulation, this policy will lead to substantial measurement of building materials that pose little radiation risk. For this reason, a method is developed to enable assessment against the 1-mSv value not on the basis of gamma-spectrometric analysis but rather based on the product's material composition. The proposed method prescribes a maximum permitted content of raw materials with potentially elevated activity concentrations in terms of a weight percentage of the end product, where the raw materials of concern are defined as those listed in Annex XIII of the EU-BSS. The permitted content is a function of the product's surface density. Therefore, a product with a low surface density of up to 25 kg m can consist of nearly 100% raw materials with potentially elevated activity concentrations, and this percentage drops to around 15% for products with a surface density of around 500 kg m. Building materials that comply with these requirements on product composition are exempt from testing, while products that do not comply must perform regular gamma-spectrometric analysis. A full validation and testing of the method is provided. In addition, the paper discusses issues relevant for regulatory implementation.

Extraction and Enrichment of Protein from Red and Green Macroalgae.

PubMed

Harnedy, Pádraigín A; FitzGerald, Richard J

2015-01-01

Macroalgae, in particular red and green species, are gaining interest as protein-rich foods for human consumption and sources of proteinaceous biofunctional peptide ingredients. During protein extraction the starting raw material, the cell disruption method utilized and the reagents employed have a major effect on the yield of protein recovered. A method is described herein for extraction and semi-purification of food-grade aqueous and alkaline soluble proteins from red and green macroalgae. Dried milled macroalgae are disrupted by osmotic shock with subsequent removal of aqueous soluble proteins by centrifugation. Alkaline soluble proteins are removed following consecutive treatment of the resultant pellet with an alkaline solution. Aqueous and alkaline soluble proteins are then enriched from the crude extracts by isoelectric precipitation.

Asbestos Utilization Costs on the Example of Functioning Landfill of Hazardous Waste

NASA Astrophysics Data System (ADS)

Polek, Daria

2017-12-01

Asbestos is a trademark of mineral fibres, which are the natural minerals found in nature. Products containing asbestos fibres, in accordance with the national and EU legislation, are covered by the production prohibition and forced to be removed. In Poland, the asbestos removal process started with the adaptation of the EU law by the Council of Ministers Treatment Program of the National Asbestos for the years 2009-2032. The purpose of the dissertation was to analyse the costs associated with the disposal of the costs of collection, transport and disposal of waste. Methodology consisted in obtaining information on the raw materials needed to produce asbestos sheets. The analysis allowed us to determine the asbestos removal cost and include state subsidies in the calculations.

Biotechnologies for critical raw material recovery from primary and secondary sources: R&D priorities and future perspectives.

PubMed

Hennebel, Tom; Boon, Nico; Maes, Synthia; Lenz, Markus

2015-01-25

Europe is confronted with an increasing supply risk of critical raw materials. These can be defined as materials of which the risks of supply shortage and their impacts on the economy are higher compared to most of other raw materials. Within the framework of the EU Innovation Partnership on raw materials Initiative, a list of 14 critical materials was defined, including some bulk metals, industrial minerals, the platinum group metals and rare earth elements. To tackle the supply risk challenge, innovation is required with respect to sustainable primary mining, substitution of critical metals, and urban mining. In these three categories, biometallurgy can play a crucial role. Indeed, microbe-metal interactions have been successfully applied on full scale to win materials from primary sources, but are not sufficiently explored for metal recovery or recycling. On the one hand, this article gives an overview of the microbial strategies that are currently applied on full scale for biomining; on the other hand it identifies technologies, currently developed in the laboratory, which have a perspective for large scale metal recovery and the needs and challenges on which bio-metallurgical research should focus to achieve this ambitious goal. Copyright © 2013. Published by Elsevier B.V.

Total materials consumption; an estimation methodology and example using lead; a materials flow analysis

USGS Publications Warehouse

Biviano, Marilyn B.; Wagner, Lorie A.; Sullivan, Daniel E.

1999-01-01

Materials consumption estimates, such as apparent consumption of raw materials, can be important indicators of sustainability. Apparent consumption of raw materials does not account for material contained in manufactured products that are imported or exported and may thus under- or over-estimate total consumption of materials in the domestic economy. This report demonstrates a methodology to measure the amount of materials contained in net imports (imports minus exports), using lead as an example. The analysis presents illustrations of differences between apparent and total consumption of lead and distributes these differences into individual lead-consuming sectors.

Application of thermogravimetry-differential thermal analysis (TG-DTA) technique to study the ancient potteries from Vellore dist, Tamilnadu, India

NASA Astrophysics Data System (ADS)

Ravisankar, R.; Naseerutheen, A.; Rajalakshmi, A.; Raja Annamalai, G.; Chandrasekaran, A.

2014-08-01

The characterization of archeological ceramic and pottery can be studied for the determination of firing temperature and the presence of raw materials by thermal analysis. Clay minerals are the main material for the production of ceramic and pottery and show some characteristic reactions such as dehydration, dehydroxylation and transformation. This is key point of criteria for the elucidation of firing temperature and raw material analysis. In the present work, DTA-TG, XRD and EDXRF technique are applied on representative potsherds from Vellore dist., Tamilnadu, India to derive the information about the production technology, raw materials and firing temperature. From the analysis, all the samples were considered to be fired from 800 °C to 900 °C and organic material might be added intestinally as a binder in the preparation of pottery.

Pulpwood production in the Northeast 1968

Treesearch

James T. Bones; Neal P. Kingsley

1969-01-01

This report is based on a canvass of all pulpmills in the Northeast that use wood-either round wood or chips-as a basic raw material for a variety of products. Mills that use woodpulp as a raw material for insulation board and hardboard were also included in the canvass. However, the canvass did not include mills that use waste paper, rags, or pulping material other...

77 FR 5846 - Importer of Controlled Substances; Notice of Registration

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-06

... import narcotic raw material are not appropriate, in accordance with 72 FR 3417 (2007). DEA has... basic classes of controlled substances: Drug Schedule Phenylacetone (8501) II Opium, raw (9600) II Poppy... to use it as a base material in the bulk manufacture of another controlled substance. No comments or...

Indonesian Politics and Economics (Selected Translations).

DTIC Science & Technology

1961-01-10

the’rise of industries to such a proportion, particularly’in England, that it brought about the " industrial revolution ".. ’ -: Surplus capital...only limited sources of raw materials. The industrial revolution , in iEngland required an inöreased supply of raw materials, and at the sam§ time the

40 CFR 63.2550 - What definitions apply to this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

... definition of reconstruction in § 63.2. Consumption means the quantity of all HAP raw materials entering a... the process as well as added as a raw material, consumption includes the quantity generated in the... contain primarily carbon, hydrogen, and oxygen atoms. Organic peroxides means organic compounds containing...

40 CFR 63.2550 - What definitions apply to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

... definition of reconstruction in § 63.2. Consumption means the quantity of all HAP raw materials entering a... the process as well as added as a raw material, consumption includes the quantity generated in the... contain primarily carbon, hydrogen, and oxygen atoms. Organic peroxides means organic compounds containing...

40 CFR 63.2550 - What definitions apply to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... definition of reconstruction in § 63.2. Consumption means the quantity of all HAP raw materials entering a... the process as well as added as a raw material, consumption includes the quantity generated in the... contain primarily carbon, hydrogen, and oxygen atoms. Organic peroxides means organic compounds containing...

40 CFR 63.2550 - What definitions apply to this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

... definition of reconstruction in § 63.2. Consumption means the quantity of all HAP raw materials entering a... the process as well as added as a raw material, consumption includes the quantity generated in the... contain primarily carbon, hydrogen, and oxygen atoms. Organic peroxides means organic compounds containing...

Waste Material Based "Terrazzo" Tiles: The Effect Of Curing Time And Extreme Environmental Conditions Over Glass Aggregate/Cement Matrix Boundary

NASA Astrophysics Data System (ADS)

Paris, E.; Radica, F.; Stabile, P.; Ansaloni, F.; Giuli, G.; Carroll, M. R.

2017-12-01

Currently, more than half of all materials extracted globally (over three billion tonnes/year in the EU only) are transformed for use in construction. Before year 2020, the EU aims to reduce the environmental impact of the construction sector by recycling or re-using large amounts of these materials, thus reducing the consumption of raw materials and helping promote the sector's economic stability. With this challenge in mind an aesthetically pleasant and fully recycled (up to 78%) pre-cast cement based tile (Terrazzo tiles) was designed by replacing raw materials with Glass Waste (GW) and Construction/Demolition Waste (CDW). Several recent studies explored the effect of the addition of GW in the manufacture of urban pavements, concluding that the use of GW can improve various phases of pavement life and structure by enhancing the structural performance, durability, environmental friendliness, and aesthetic features. In this study we extend this knowledge also to interior cement-based tiles by evaluating the technical performances of this this novel designed tile, in particular by focusing on the interface between the GW aggregates and different Portland cement based matrix at extreme environmental conditions. For this work three representative waste material based "terrazzo" tiles were selected and characterized by means of XRD and SEM imaging in order to study the boundary effect between GW aggregate and different binding materials: limestone powder, quartz powder and fine ground WG powder. A fourth additional mixture of Portland cement and CDW material was characterized. Fragments of a Limestone matrix tile were also thermally threated at -18°C and at 60°C for one week to witness the possible formation of new harmful phases at the grain-matrix boundary. Preliminary results on X-ray diffraction patterns show that 1 year after manufacture and/or thermal treatment there is no new formation of harmful phases other than the starting ones. High magnification SEM imaging further confirmed this observation also highlighting the good binding performances of a mixture composed by the 78% of recycled WG.

Battery Data MI Importer Template Quick Start Guide

NASA Technical Reports Server (NTRS)

Levinson, Laurie H.

2017-01-01

In order to ensure the persistent availability and reliability of test data generated over the course of the project, the M-SHELLS Project has decided to store acquired test data, as well as associated pedigree information, in the Granta Materials Intelligence (MI) database. To facilitate that effort, an importer template and associated graphical user interface (GUI) software have been developed, with this guide providing the operating instructions for their use. The template and automation software GUI are contained in the BatteryDataImporter.xlsm Excel workbook, and are to be used to import M-SHELLS summary, or pedigree, data and the associated raw test data results into an importer template-based file, formatted in such a way as to be ready for immediate upload to the Test Data: Battery Performance table of the Granta MI database. The provided GUI enables the user to select the appropriate summary data file(s), with each file containing the required information to identify any associated raw test data file(s) to be processed. In addition to describing the setup and operation of the importer template and GUI software, this guide also provides instructions for uploading processed data to the database and for viewing the data following upload.

75 FR 10460 - Improving Tracing Procedures for E. coli O157:H7 Positive Raw Beef Product

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-08

... Tracing Procedures for E. coli O157:H7 Positive Raw Beef Product AGENCY: Food Safety and Inspection... Agency procedures for identifying suppliers of source material used to produce raw beef product that FSIS... that raw beef is positive for E. coli O157:H7, and whether the Agency takes the appropriate steps to...

Influence of boiling point range of feedstock on properties of derived mesophase pitch

NASA Astrophysics Data System (ADS)

Yu, Ran; Liu, Dong; Lou, Bin; Chen, Qingtai; Zhang, Yadong; Li, Zhiheng

2018-06-01

The composition of raw material was optimized by vacuum distillation. The carbonization behavior of two kinds of raw material was followed by polarizing microscope, softening point, carbon yield and solubility. Two kinds of mesophase pitch have been monitored by X-ray diffraction (XRD), Fourier transform infrared spectrometer (FTIR), elemental analysis and 1H nuclear magnetic resonance (1H-NMR). The analysis results suggested that raw material B (15wt% of A was distillated out and the residue named B) could form large domain mesophase pitch earlier. The shortened heat treat time favored the retaining of alkyl group in mesophase pitch and reduced the softening point of masophase pitch.

Sensitization to fragrance materials in Indonesian cosmetics.

PubMed

Roesyanto-Mahadi, I D; Geursen-Reitsma, A M; van Joost, T; van den Akker, T W

1990-04-01

2 different groups of patients were patch tested with 2 test series (A and B) containing extracts of fragrance raw materials, traditionally used in Indonesian cosmetics. Series A consisted of diluted extracts of commercially available Indonesian fragrances. Series B consisted of extracts prepared in our department from corresponding indigenous flowers and fruits. Group 1 consisted of 32 patients positive to fragrance-mix, of whom 8 (25%) had positive tests to 1 or more of the different extracts of fragrance raw materials. Reactions were observed to extracts of: Rosa hybrida Hort (7); Canangium odoratum Baill (5); Citrus aurantifolia Swingle (4); Jasminum sambac Ait (2). 6 of the 8 patients had reactions to 1 or more of the components of fragrance-mix: oakmoss (3); cinnamic alcohol (2), isoeugenol (1); cinnamic aldehyde (1) and geraniol (1). Group 2 consisted of 159 patients patch tested on suspicion of contact dermatitis, who were fragrance-mix negative. Only 2 (1.2%) had a positive patch test to the extracts of fragrance raw materials. Specimens taken (as is) from the flowers and citrus fruits (being the basis sources of the fragrance raw materials) were less antigenic. The use of additional test series in Indonesia to detect allergy to traditional cosmetics and perfumes merits further investigation.

77 FR 5846 - Importer of Controlled Substances; Notice of Registration

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-06

... following basic classes of controlled substances: Drug Schedule Opium, raw (9600) II Poppy Straw Concentrate (9670) II The company plans to import narcotic raw materials for manufacturing and further distribution... substances that are manufactured from opium, raw, and poppy straw concentrate. Comments and requests for...

Reduction of CO2 diffuse emissions from the traditional ceramic industry by the addition of Si-Al raw material.

PubMed

González, I; Barba-Brioso, C; Campos, P; Romero, A; Galán, E

2016-09-15

The fabrication of ceramics can produce the emission of several gases, denominated exhaust gases, and also vapours resulting from firing processes, which usually contain metals and toxic substances affecting the environment and the health of workers. Especially harmful are the diffuse emissions of CO2, fluorine, chlorine and sulphur from the ceramics industry, which, in highly industrialized areas, can suppose an important emission focus of dangerous effects. Concerning CO2, factories that use carbonate-rich raw materials (>30% carbonates) can emit high concentrations of CO2 to the atmosphere. Thus, carbonate reduction or substitution with other raw materials would reduce the emissions. In this contribution, we propose the addition of Al-shales to the carbonated ceramic materials (marls) for CO2 emission reduction, also improving the quality of the products. The employed shales are inexpensive materials of large reserves in SW-Spain. The ceramic bodies prepared with the addition of selected Al-shale to marls in variable proportions resulted in a 40%-65% CO2 emission reduction. In addition, this research underlines at the same time that the use of a low-price raw material can also contribute to obtaining products with higher added value. Copyright © 2016 Elsevier Ltd. All rights reserved.

Quality assurance of herbal raw materials in supply chain: challenges and opportunities.

PubMed

Govindaraghavan, Suresh

2008-01-01

The herbal medicine industry is presently adopting modern scientific tools to substantiate the guarantee of efficacy that, in the past, rested only on anecdotal evidence derived from traditional knowledge systems. This is particularly true for the processes of identification of herbal raw materials adopting modern tools for phytochemical fingerprinting. The successful adaptation of available technologies and practices depends on an understanding of the phytochemical complexity and variability innate in biological material. It challenges the "mainstream medicinal mindset" that "tend(s) to reject …. therapies for which mechanisms of action do not fit within Newtonian, biochemical orientation" (Dumoff, 2003). The herbal medicinal industry is independently evolving its own rigid quality assurance and control systems using Good Manufacturing Practice (GMP) and Good Laboratory Practice (GLP) guidelines, but it faces unique difficulties. These include lack of Good Agricultural and Collection Practice (GACP), lack of transparency in the raw material supply chain so as to preclude the use of unsafe practices, problems in the authentication of herbal raw materials, and a general lack of understanding of the need to reduce phytochemical variability in these materials. This paper explores these difficulties and outlines strategies to overcome them, but these strategies will require coordinated international government regulations to be fully effective.

The Role of China in the UK Relative Imports from Three Selected Trading Regions: The Case of Textile Raw Material Industry.

PubMed

Xu, Junqian

2017-11-30

The UK textile industry was very prosperous in the past but in the 1970s Britain started to import textile materials from abroad. Since 1990, half of its textile materials have been imported from the EEA (European Economic Area), ASEAN (Association of Southeast Asian Nations) and North America countries. Meanwhile, UK imports from China have increased dramatically. Through comparisons, this paper calculates the trade competitiveness index and relative competitive advantages of regions and investigates the impact of Chinese textiles on UK imports from three key free trade regions across the textile sectors in the period 1990-2016 on the basis of United Nation Comtrade Rev. 3. We find that China's textile prices, product techniques, political trade barriers and even tax system have made a varied impact on the UK's imports across related sectors in the context of green trade and the strengthening of barriers, which helps us recognize China's competitiveness in international trading and also provides advice on China's sustainable development of textile exports.

Validated method for quantification of genetically modified organisms in samples of maize flour.

PubMed

Kunert, Renate; Gach, Johannes S; Vorauer-Uhl, Karola; Engel, Edwin; Katinger, Hermann

2006-02-08

Sensitive and accurate testing for trace amounts of biotechnology-derived DNA from plant material is the prerequisite for detection of 1% or 0.5% genetically modified ingredients in food products or raw materials thereof. Compared to ELISA detection of expressed proteins, real-time PCR (RT-PCR) amplification has easier sample preparation and detection limits are lower. Of the different methods of DNA preparation CTAB method with high flexibility in starting material and generation of sufficient DNA with relevant quality was chosen. Previous RT-PCR data generated with the SYBR green detection method showed that the method is highly sensitive to sample matrices and genomic DNA content influencing the interpretation of results. Therefore, this paper describes a real-time DNA quantification based on the TaqMan probe method, indicating high accuracy and sensitivity with detection limits of lower than 18 copies per sample applicable and comparable to highly purified plasmid standards as well as complex matrices of genomic DNA samples. The results were evaluated with ValiData for homology of variance, linearity, accuracy of the standard curve, and standard deviation.

The Role of China in the UK Relative Imports from Three Selected Trading Regions: The Case of Textile Raw Material Industry

PubMed Central

Xu, Junqian

2017-01-01

The UK textile industry was very prosperous in the past but in the 1970s Britain started to import textile materials from abroad. Since 1990, half of its textile materials have been imported from the EEA (European Economic Area), ASEAN (Association of Southeast Asian Nations) and North America countries. Meanwhile, UK imports from China have increased dramatically. Through comparisons, this paper calculates the trade competitiveness index and relative competitive advantages of regions and investigates the impact of Chinese textiles on UK imports from three key free trade regions across the textile sectors in the period 1990–2016 on the basis of United Nation Comtrade Rev. 3. We find that China’s textile prices, product techniques, political trade barriers and even tax system have made a varied impact on the UK’s imports across related sectors in the context of green trade and the strengthening of barriers, which helps us recognize China’s competitiveness in international trading and also provides advice on China’s sustainable development of textile exports. PMID:29189756

Research and development in pilot plant production of granular NPK fertilizer

NASA Astrophysics Data System (ADS)

Failaka, Muhamad Fariz; Firdausi, Nadia Zahrotul; Chairunnisa, Altway, Ali

2017-05-01

PT Pupuk Kaltim (Pupuk Kaltim) as one of the biggest fertilizer manufacturer in Indonesia, always striving to improve the product quality and achieve the optimal performance while facing the challenges of global competition NPK (Nitrogen, Phosphorus, Potassium) market. In order to continuously improve operations and processes of two units NPK compound plant, Pupuk Kaltim has successfully initiated a new facility which is referred to as a NPK pilot-scale research facility with design capacity of 30 kg/hr. This mini-plant is used to assist in the scale up of new innovations from laboratory research to better understand the effect of using new raw materials and experiment with process changes to improve quality and efficiency. The pilot installation is composed of the following main parts: mixer, screw feeder, granulator, dryer and cooler. The granulator is the equipment where NPK granules is formed by spraying appropriate steam and water onto raw materials in a rotating drum. The rotary dryer and cooler are intended for the drying process where temperature reduction and the final moisture are obtained. As a part of innovations project since 2014, the pilot plant has conducted many of experiments such as trials using Ammonium Sulfate (ZA) as a new raw material, alternative raw materials of Diammonium Phosphate (DAP), Potassium Chloride (KCl) and clay, and using a novel material of fly ash. In addition, the process engineering staff also conduct the trials of raw materials ratio so that an ideal formulation with lower cost can be obtained especially when it is applied in the existing full-scale plant.

Pulpwood - 1976

Treesearch

James T. Bones; David R. Dickson

1977-01-01

This annual report is based on a canvass of all pulpmills in the Northeast that use wood-either roundwood or plant residues-as a basic raw material. Cross-boundary shipments are traced by exchanging information with neighboring experiment stations that conduct similar canvasses. Mills that use pulpwood as a raw material in producing insulation board and hardboard were...

9 CFR 351.14 - Processes to be supervised; extent of examinations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... examinations. 351.14 Section 351.14 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT... be at least once a month if the plant consistently handles only raw materials acceptable under § 351... consistently handles some raw materials that are acceptable, and some that are unacceptable, under § 351.3, for...

40 CFR Table N-1 to Subpart N of... - CO2 Emission Factors for Carbonate-Based Raw Materials

Code of Federal Regulations, 2014 CFR

2014-07-01

... Raw Materials Carbonate-basedraw material—mineral CO2 emission factor a Limestone—CaCO3 0.440 Dolomite—CaMg(CO3)2 0.477 Sodium carbonate/soda ash—Na2CO3 0.415 Barium carbonate—BaCO3 0.223 Potassium...

40 CFR Table N-1 to Subpart N of... - CO2 Emission Factors for Carbonate-Based Raw Materials

Code of Federal Regulations, 2012 CFR

2012-07-01

... Raw Materials Carbonate-basedraw material—mineral CO2 emission factor a Limestone—CaCO3 0.440 Dolomite—CaMg(CO3)2 0.477 Sodium carbonate/soda ash—Na2CO3 0.415 Barium carbonate—BaCO3 0.223 Potassium...

40 CFR Table N-1 to Subpart N of... - CO2 Emission Factors for Carbonate-Based Raw Materials

Code of Federal Regulations, 2013 CFR

2013-07-01

... Raw Materials Carbonate-basedraw material—mineral CO2 emission factor a Limestone—CaCO3 0.440 Dolomite—CaMg(CO3)2 0.477 Sodium carbonate/soda ash—Na2CO3 0.415 Barium carbonate—BaCO3 0.223 Potassium...

76 FR 14910 - Small Diameter Graphite Electrodes From the People's Republic of China: Initiation of Anti...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-18

... correct grade of petroleum coke mix, and have been baked, formed, carbonized, impregnated, and graphitized... required for the production of SDGE (e.g., raw material handling, mixing, forming, baking, impregnating... production process, demonstrating how raw materials are formed, baked, impregnated (if needed), re-baked...

Characteristics and production of tantalum powders for solid-electrolyte capacitors

NASA Astrophysics Data System (ADS)

Yoon, Jae Sik; Kim, Byung Il

The effects of using K 2TaF 7 as the raw material and sodium as the reducing agent on the characteristics of tantalum powder are investigated. Batch-type metallothermic reduction (BTMR) is used to charge the reactor with the raw material and the reducing agent, and external continuous supply metallothermic reduction (ESMR) is used to supply the raw material and the reducing agent at a constant rate at the temperature of the reduction reaction. In the case of ESMR, the yield increases by several tens of percent because of the uniform reaction between the raw material and the reducing agent. It is possible to obtain a powder of over 99.5% purity. The powder particles obtained with BTMR are relatively large (4-6 μm) and have a coarse lamellar shape, while those prepared via ESMR are of uniform 1-2 μm size with a coral-like shape. Measurements of the electric properties show that the leakage current and the dielectric dissipation are low with higher reliability in ESMR than in BTMR, and the capacitance is 26,000 and 8400 CV for ESMR and in BTMR, respectively.

Recycling the product of thermal transformation of cement-asbestos for the preparation of calcium sulfoaluminate clinker.

PubMed

Viani, Alberto; Gualtieri, Alessandro F

2013-09-15

According to recent resolutions of the European Parliament (2012/2065(INI)), the need for environmentally friendly alternative solutions to landfill disposal of hazardous wastes, such as asbestos-containing materials, prompts their recycling as secondary raw materials (end of waste concept). In this respect, for the first time, we report the recycling of the high temperature product of cement-asbestos, in the formulation of calcium sulfoaluminate cement clinkers (novel cementitious binders designed to reduce CO₂ emissions), as a continuation of a previous work on their systematic characterization. Up to 29 wt% of the secondary raw material was successfully introduced into the raw mix. Different clinker samples were obtained at 1250 °C and 1300 °C, reproducing the phase composition of industrial analogues. As an alternative source of Ca and Si, this secondary raw material allows for a reduction of the CO₂ emissions in cement production, mitigating the ecological impact of cement manufacturing, and reducing the need for natural resources. Copyright © 2013 Elsevier B.V. All rights reserved.

77 FR 64142 - Importer of Controlled Substances, Notice of Application, Noramco, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-18

... following basic classes of controlled substances: Drug Schedule Phenylacetone (8501) II Opium, raw (9600) II Poppy Straw Concentrate (9670) II Tapentadol (9780) II The company plans to import raw Opium (9600) and... substance. Comments and requests for hearings on applications to import narcotic raw material are not...

76 FR 62447 - Importer of Controlled Substances; Notice of Application

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-07

... registration as an importer of the following basic classes of controlled substances: Drug Schedule Opium, raw (9600) II Poppy Straw Concentrate (9670) II The company plans to import narcotic raw materials for... several controlled substances that are manufactured from raw opium, poppy straw, and concentrate of poppy...

77 FR 60143 - Importer of Controlled Substances; Notice of Registration; Cody Laboratories, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-02

... importer of the following basic classes of controlled substances: Drug Schedule Opium, raw (9600) II Concentrate Poppy Straw (9670) II Tapentadol (9780) II The company plans to import narcotic raw materials for... several controlled substances that are manufactured from opium raw, and poppy straw concentrate. The...

76 FR 17967 - Importer of Controlled Substances; Notice of Registration

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-31

... basic classes of controlled substances: Drug Schedule Raw Opium (9600) II Concentrate of Poppy Straw (9670) II The company plans to import narcotic raw materials for manufacturing and further distribution... substances that are manufactured from raw opium, poppy straw, and concentrate of poppy straw. No comments or...

75 FR 32506 - Importer of Controlled Substances; Notice of Registration

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-08

... of controlled substances listed in schedule II: Drug Schedule Raw Opium (9600) II Concentrate of Poppy Straw (9670) II The company plans to import narcotic raw materials for manufacturing and further... substances that are manufactured from raw opium, poppy straw, and concentrate of poppy straw. No comments or...

Determination of Coenzyme Q10 Content in Raw Materials and Dietary Supplements by High-Performance Liquid Chromatography-UV: Collaborative Study

PubMed Central

Lunetta, Steven; Roman, Mark

2008-01-01

An international collaborative study was conducted of a high-performance liquid chromatographic (HPLC)-UV method for the determination of coenzyme Q10 (CoQ10, ubidecarenone) in raw materials and dietary supplements. Ten collaborating laboratories determined the total CoQ10 content in 8 blind duplicate samples. Sample materials included CoQ10 raw material and 4 finished product dietary supplements representing softgels, hardshell gelatin capsules, and chewable wafers. In addition, collaborating laboratories received a negative control and negative control spiked with CoQ10 at low and high levels to determine recovery. Materials were extracted with an acetonitrile–tetrahydrofuran–water mixture. Ferric chloride was added to the test solutions to ensure all CoQ10 was in the oxidized form. The HPLC analyses were performed on a C18 column using UV detection at 275 nm. Repeatability relative standard deviations (RSDr) ranged from 0.94 to 5.05%. Reproducibility relative standard deviations (RSDR) ranged from 3.08 to 17.1%, with HorRat values ranging from 1.26 to 5.17. Recoveries ranged from 74.0 to 115%. Based on these results, the method is recommended for Official First Action for determination of CoQ10 in raw materials and dietary supplement finished products containing CoQ10 at a concentration of >100 mg CoQ10/g test material. PMID:18727527

Determination of coenzyme Q10 content in raw materials and dietary supplements by high-performance liquid chromatography-UV: collaborative study.

PubMed

Lunetta, Steven; Roman, Mark

2008-01-01

An international collaborative study was conducted of a high-performance liquid chromatographic (HPLC)-UV method for the determination of coenzyme Q10 (CoQ10, ubidecarenone) in raw materials and dietary supplements. Ten collaborating laboratories determined the total CoQ10 content in 8 blind duplicate samples. Sample materials included CoQ10 raw material and 4 finished product dietary supplements representing softgels, hardshell gelatin capsules, and chewable wafers. In addition, collaborating laboratories received a negative control and negative control spiked with CoQ10 at low and high levels to determine recovery. Materials were extracted with an acetonitrile-tetrahydrofuran-water mixture. Ferric chloride was added to the test solutions to ensure all CoQ10 was in the oxidized form. The HPLC analyses were performed on a C18 column using UV detection at 275 nm. Repeatability relative standard deviations (RSDr) ranged from 0.94 to 5.05%. Reproducibility relative standard deviations (RSDR) ranged from 3.08 to 17.1%, with HorRat values ranging from 1.26 to 5.17. Recoveries ranged from 74.0 to 115%. Based on these results, the method is recommended for Official First Action for determination of CoQ10 in raw materials and dietary supplement finished products containing CoQ10 at a concentration of >100 mg CoQ10/g test material.

The Influences of Stirring and Cow Manure Added on Biogas Production From Vegetable Waste Using Anaerobic Digester

NASA Astrophysics Data System (ADS)

Abdullah, N. O.; Pandebesie, E. S.

2018-03-01

Based on Indonesian Government Regulation number 18, 2008, solid waste management should be conducted from the source to minimize the amount of waste. The process includes the waste from domestic, commercial, and institution. This also includes in 3R program (reduce, reuse, and recycle). Vegetable waste from market is a potential material to produce biogas due to its chemical composition (hemi-cellulose, cellulose, and lignin) which transform the biomass to be the raw material of biogas. Acid substance of vegetable becomes an obstacle in process of producing biogas. There has to be buffer material which can improve the performance of biogas process. Cow manure is a material which can be easily obtained as buffer. This research used 24 biogas reactor in volume 6 L by batch method. Biogas volume is measured by checking the preferment in manometer. Methane measurement is conducted by using Gas Chromatography (GC) Hewlett Packard (HP-series 6890) in day 15 and 30. The research was started by sample characterization, sample test by total solid analysis, volatile solid, lignin, ratio C/N, ammonium, and ash. Analysis of pH, temperature, and biogas volume is conducted every day.

The use of foresight methods in strategic raw materials intelligence - an international review

NASA Astrophysics Data System (ADS)

Konrat Martins, Marco Antonio; Bodo, Balazs; Falck, Eberhard

2017-04-01

Foresight methods are systematic attempts to look into the longer term future of science, society, economy and technology. There is a range of tools and techniques that can be used individually or combined, most commonly classified into qualitative, quantitative or semi-quantitative methods, that follow an exploratory or normative approach. These tools can help to identify the longer term visions, orienting policy formulation and decisions, triggering actions, among other objectives. There is an identified lack of European strategic foresight knowledge in the raw materials domain. Since the European Raw Materials Initiative was launched in 2008, the EU has been attempting to overcome challenges related to the future access of non-energy and non-agricultural raw materials. In this context, the ongoing H2020 project, MICA (Mineral Intelligence Capacity Analysis, Grant Agreement No. 689648), has been launched to answer to stakeholders needs by consolidating relevant data, determining relevant methods and tools, and investigating Raw Materials Intelligence options for European mineral policy development, all tailored to fit under the umbrella of a European Raw Materials Intelligence Capacity Platform (EU-RMICP). As part of the MICA activities, an assessment of best practices and benchmarks of international raw materials foresight case studies has been carried out in order to review how EU and non-EU countries have employed foresight. A pool of 30 case studies has been collected and reviewed internationally, one third of which were selected for detailed assessment. These were classified according to their background and goals, in function of methods employed, and to the purpose of each method in the study: a total of 12 different methods were identified in these studies. For longer time frames, qualitative predictive methods such as Scenario Development have been repeatedly observed for mineral raw materials foresight studies. Substantial variations were observed in terms of use and deployment of the scenarios. Pre-defined global scenarios can be used to explore futures thinking over a given theme - a step in the process - whereas the development of specific scenarios can be the main element of the study. The former was used to consider future strategies at different levels and how different futures influence the sector, whilst the latter was preferably used as means of assessment of sector capabilities and the current readiness for future challenges. Other methods such as SWOT, STEEP (Social, Technological, Economical, Environmental and Political scanning) and Brainstorming can be observed supporting the Scenarios, helping to provide either input for its development or post-processing its outcomes towards overall objectives. The volatility of the mineral raw materials sector presents a natural inclination towards more explorative and creativity-based methods. Such methods can address the necessity of understanding how different factors may play out in the future, where critical uncertainties can dictate a range of possible futures. Therefore, having a solid backdrop for alternative paths is extremely useful for policy and decision-makers to propose actions and respond in a timely manner to the future challenges of the sector.

Green biorefinery - Industrial implementation.

PubMed

Kamm, B; Schönicke, P; Hille, Ch

2016-04-15

Oil refineries currently generate a multitude of products for almost every sphere of life at very high efficiency. However, fossil raw materials are just available in limited quantities. The development of comparable BIOREFINERIES is necessary to make a variety of competitive biological products regarding their equivalent products based on fossil raw materials. The product range of a biorefinery comprises products that can be manufactured on the basis of crude oil, as well as such products that cannot be produced on the basis of crude oil (Kamm, Gruber, & Kamm, 2011). GREEN BIOREFINERIES [GBR's] are complex systems of sustainable, environment- and resource-friendly technologies for a comprehensive material and energy use or recovery of renewable raw materials in form of green and waste biomasses from a sustainable land use as target (Kamm et al., 2009; Digman, Runge, Shinners, & Hatfield, 2013). Copyright © 2015. Published by Elsevier Ltd.

The utilization of nonterrestrial materials. [resources for solar power satellite construction

NASA Technical Reports Server (NTRS)

1981-01-01

The development of research and technology programs on the user of nonterrestrial materials for space applications was considered with emphasis on the space power satellite system as a model of large space systems for which the use of nonterrestrial materials may be economically viable. Sample topics discussed include the mining of raw materials and the conversion of raw materials into useful products. These topics were considered against a background of the comparative costs of using terrestrial materials. Exploratory activities involved in the preparation of a nonterrestrial materials utilization program, and the human factors involved were also addressed. Several recommendations from the workshop are now incorporated in NASA activities.

Petrographic characterization of lunar soils: Application of x ray digital-imaging to quantitative and automated analysis

NASA Technical Reports Server (NTRS)

Higgins, Stefan J.; Patchen, Allan; Chambers, John G.; Taylor, Lawrence A.; Mckay, David S.

1994-01-01

The rocks and soils of the moon will be the raw materials for various engineering needs at a lunar base, such as sources of hydrogen, oxygen, metals, etc. The material of choice for most of the bulk needs is the regolith and its less than 1 cm fraction, the soil. For specific mineral resources it may be necessary to concentrate minerals from either rocks or soils. Therefore, quantitative characterizations of these rocks and soils are necessary in order to better define their mineral resource potential. However, using standard point-counting microscopic procedures, it is difficult to quantitatively determine mineral abundances and virtually impossible to obtain data on mineral distributions within grains. As a start to fulfilling these needs, Taylor et al. and Chambers et al. have developed a procedure for characterization of crushed lunar rocks using x ray digital imaging. The development of a similar digital imaging procedure for lunar soils as obtained from a spectrometer is described.

A study on specific heat capacities of Li-ion cell components and their influence on thermal management

NASA Astrophysics Data System (ADS)

Loges, André; Herberger, Sabrina; Seegert, Philipp; Wetzel, Thomas

2016-12-01

Thermal models of Li-ion cells on various geometrical scales and with various complexity have been developed in the past to account for the temperature dependent behaviour of Li-ion cells. These models require accurate data on thermal material properties to offer reliable validation and interpretation of the results. In this context a thorough study on the specific heat capacities of Li-ion cells starting from raw materials and electrode coatings to representative unit cells of jelly rolls/electrode stacks with lumped values was conducted. The specific heat capacity is reported as a function of temperature and state of charge (SOC). Seven Li-ion cells from different manufactures with different cell chemistry, application and design were considered and generally applicable correlations were developed. A 2D thermal model of an automotive Li-ion cell for plug-in hybrid electric vehicle (PHEV) application illustrates the influence of specific heat capacity on the effectivity of cooling concepts and the temperature development of Li-ion cells.

Manufacture of mold of polymeric composite water pipe reinforced charcoal

NASA Astrophysics Data System (ADS)

Zulfikar; Misdawati; Idris, M.; Nasution, F. K.; Harahap, U. N.; Simanjuntak, R. K.; Jufrizal; Pranoto, S.

2018-03-01

In general, household wastewater pipelines currently use thermoplastic pipes of Polyvinyl Chloride (PVC). This material is known to be not high heat resistant, contains hazardous chemicals (toxins), relatively inhospitable, and relatively more expensive. Therefore, researchers make innovations utilizing natural materials in the form of wood charcoal as the basic material of making the water pipe. Making this pipe requires a simple mold design that can be worked in the scale of household and intermediate industries. This research aims to produce water pipe mold with simple design, easy to do, and making time relatively short. Some considerations for molding materials are weight of mold, ease of raw material, strong, sturdy, and able to cast. Pipe molds are grouped into 4 (four) main parts, including: outer diameter pipe molding, pipe inside diameter, pipe holder, and pipe alignment control. Some materials have been tested as raw materials for outer diameter of pipes, such as wood, iron / steel, cement, and thermoset. The best results are obtained on thermoset material, where the process of disassembling is easier and the resulting mold weight is relatively lighter. For the inside diameter of the pipe is used stainless steel, because in addition to be resistant to chemical processes that occur, in this part of the mold must hold the press load due to shrinkage of raw materials of the pipe during the process of hardening (polymerization). Therefore, it needs high pressure resistant material and does not blend with the raw material of the pipe. The base of the mold is made of stainless steel material because it must be resistant to corrosion due to chemical processes. As for the adjustment of the pipe is made of ST 37 carbon steel, because its function is only as a regulator of the alignment of the pipe structure.

North Carolina Forest Resources and Industries

Treesearch

J.W. Cruikshank

1944-01-01

Dependable information on the supply of all raw materials is vital to the conduct of the war and to the success of current and future efforts at post-war planning. This economic survey of our forests which are an integral part of the Nation's reservoir of raw material is essential to a complete understanding of resource potentialities and of the industries...

Preparation of wood for energy use

Treesearch

Donald L. Sirois; Bryce J. Stokes

1985-01-01

This paper presents an overview & current sources and forms of raw materials for wood energy use and the types of machines available to convert them to the desired form for boiler fuel. Both the fuel source or raw material, and the combustion furnace will dictate the requirements for the processing system. Because of the wide range of processing equipment...

The pallet industry: a changing hardwood market

Treesearch

G.P. Dempsey; D.G. Martens

1991-01-01

From its inception during World War II, the wooden pallet industry has grown to become the Nation's largest industrial consumer of hardwood lumber products. Since most of the raw material in wooden pallets is lower grade lumber, the pallet industry's growth, efficiency, and changing raw material inputs must be of concern to the grade hardwood lumber industry...

Acoustic assessment of wood quality of raw forest materials : a path to increased profitability

Treesearch

Xiping Wang; Peter Carter; Robert J. Ross; Brian K. Brashaw

2007-01-01

Assessment of the quality of raw wood materials has become a crucial issue in the operational value chain as forestry and the wood processing industry are increasingly under economic pressure to maximize extracted value. A significant effort has been devoted toward developing robust nondestructive evaluation (NDE) technologies capable of predicting the intrinsic wood...

Pulpwood production in the Northeast - 1974

Treesearch

James T. Bones; David R. Dickson

1976-01-01

This annual report is based on a canvass of all pulpmills in the Northeast that use wood-either roundwood or plant residues-as a basic raw material for a variety of products. Cross-boundary shipments were traced by exchanging information with neighboring experiment stations that conduct similar canvasses. Mills that use pulpwood as a raw material in producing...

Pulpwood production in the Northeast - 1975

Treesearch

James T. Bones; David R. Dickson

1976-01-01

This annual report is based on a canvass of all pulpmills in the Northeast that use wood-either roundwood or plant residues-as a basic raw material for a variety of products. Cross-boundary shipments are traced by exchanging information with neighboring experiment stations that conduct similar canvasses. Mills that use pulpwood as a raw material in producing insulation...

Metabolic Noise, Vestigial Metabolites or the Raw Material of Ecological Adaptation? Opportunitistic Enzymes, Catalytic Promiscuity and the Evolution of Chemodiversity in Nature (2010 JGI User Meeting)

ScienceCinema

Noel, Joseph

2018-04-26

Joseph Noel from the Salk Institute on "Metabolic Noise, Vestigial Metabolites or the Raw Material of Ecological Adaptation? Enzymes, Catalytic Promiscuity and the Evolution of Chemodiversity in Nature" on March 26, 2010 at the 5th Annual DOE JGI User Meeting.

Navy Fact File 1984

DTIC Science & Technology

1984-10-01

Textile Fibers/Products Foods , Feeds, Beverages Industrial Supplies Value of Goods Exported ($ billions) 1958 1968 1978 $18.1 billion...character of its government, the soundness of its economy, its industrial efficiency, the development of its internal communications, the quality...decades the United States produced more raw materials than its growing industrial complex could consume. From a raw-materials-surplus-nation we

Characterization of ZrO2-Y2O3 thermal spray powder systems

NASA Technical Reports Server (NTRS)

Mantkowski, Thomas E.; Rigney, David V.; Froning, Marc J.; Jayaraman, N.

1985-01-01

The overall objective is to establish the interrelation between the raw material in the coating process and the performance of the coating deposit. It is anticipated that these interrelations will help establish more precise specifications for the procurement of the raw materials. Some of the preliminary results of the program are presented.

Lagrange multiplier for perishable inventory model considering warehouse capacity planning

NASA Astrophysics Data System (ADS)

Amran, Tiena Gustina; Fatima, Zenny

2017-06-01

This paper presented Lagrange Muktiplier approach for solving perishable raw material inventory planning considering warehouse capacity. A food company faced an issue of managing perishable raw materials and marinades which have limited shelf life. Another constraint to be considered was the capacity of the warehouse. Therefore, an inventory model considering shelf life and raw material warehouse capacity are needed in order to minimize the company's inventory cost. The inventory model implemented in this study was the adapted economic order quantity (EOQ) model which is optimized using Lagrange multiplier. The model and solution approach were applied to solve a case industry in a food manufacturer. The result showed that the total inventory cost decreased 2.42% after applying the proposed approach.

Carbon source in the future chemical industries

NASA Astrophysics Data System (ADS)

Hofmann, Peter; Heinrich Krauch, Carl

1982-11-01

Rising crude oil prices favour the exploitation of hitherto unutilised energy carriers and the realisation of new technologies in all sectors where carbon is used. These changed economic constraints necessitate both savings in conventional petrochemistry and a change to oil-independent carbon sources in the chemical industry. While, in coal chemistry, the synthesis and process principles of petrochemistry — fragmentation of the raw material and subsequent buildup of molecular structures — can be maintained, the raw material structure largely remains unchanged in the chemistry of renewable raw materials. This lecture is to demonstrate the structural as well as the technological and energy criteria of the chemistry of alternative carbon sources, to forecast the chances of commercial realization and to discuss some promising fields of research and development.

The cellulose resource matrix.

PubMed

Keijsers, Edwin R P; Yılmaz, Gülden; van Dam, Jan E G

2013-03-01

The emerging biobased economy is causing shifts from mineral fossil oil based resources towards renewable resources. Because of market mechanisms, current and new industries utilising renewable commodities, will attempt to secure their supply of resources. Cellulose is among these commodities, where large scale competition can be expected and already is observed for the traditional industries such as the paper industry. Cellulose and lignocellulosic raw materials (like wood and non-wood fibre crops) are being utilised in many industrial sectors. Due to the initiated transition towards biobased economy, these raw materials are intensively investigated also for new applications such as 2nd generation biofuels and 'green' chemicals and materials production (Clark, 2007; Lange, 2007; Petrus & Noordermeer, 2006; Ragauskas et al., 2006; Regalbuto, 2009). As lignocellulosic raw materials are available in variable quantities and qualities, unnecessary competition can be avoided via the choice of suitable raw materials for a target application. For example, utilisation of cellulose as carbohydrate source for ethanol production (Kabir Kazi et al., 2010) avoids the discussed competition with easier digestible carbohydrates (sugars, starch) deprived from the food supply chain. Also for cellulose use as a biopolymer several different competing markets can be distinguished. It is clear that these applications and markets will be influenced by large volume shifts. The world will have to reckon with the increase of competition and feedstock shortage (land use/biodiversity) (van Dam, de Klerk-Engels, Struik, & Rabbinge, 2005). It is of interest - in the context of sustainable development of the bioeconomy - to categorize the already available and emerging lignocellulosic resources in a matrix structure. When composing such "cellulose resource matrix" attention should be given to the quality aspects as well as to the available quantities and practical possibilities of processing the feedstock and the performance in the end-application. The cellulose resource matrix should become a practical tool for stakeholders to make choices regarding raw materials, process or market. Although there is a vast amount of scientific and economic information available on cellulose and lignocellulosic resources, the accessibility for the interested layman or entrepreneur is very difficult and the relevance of the numerous details in the larger context is limited. Translation of science to practical accessible information with modern data management and data integration tools is a challenge. Therefore, a detailed matrix structure was composed in which the different elements or entries of the matrix were identified and a tentative rough set up was made. The inventory includes current commodities and new cellulose containing and raw materials as well as exotic sources and specialties. Important chemical and physical properties of the different raw materials were identified for the use in processes and products. When available, the market data such as price and availability were recorded. Established and innovative cellulose extraction and refining processes were reviewed. The demands on the raw material for suitable processing were collected. Processing parameters known to affect the cellulose properties were listed. Current and expected emerging markets were surveyed as well as their different demands on cellulose raw materials and processes. The setting up of the cellulose matrix as a practical tool requires two steps. Firstly, the reduction of the needed data by clustering of the characteristics of raw materials, processes and markets and secondly, the building of a database that can provide the answers to the questions from stakeholders with an indicative character. This paper describes the steps taken to achieve the defined clusters of most relevant and characteristic properties. These data can be expanded where required. More detailed specification can be obtained from the background literature and handbooks. Where gaps of information are identified, the research questions can be defined that will require further investigation. Copyright © 2012 Elsevier Ltd. All rights reserved.

Whole grain for whom and why?

PubMed Central

Frølich, Wenche; Åman, Per

2010-01-01

A definition of whole grain is a critical first step in investigating health claims for whole grain and its products. Today, there is no internationally accepted definition of whole grain. Some existing definitions are broad and commodity-based, including grains with similar end uses, while others are more restricted. Scientific knowledge must be the basis for inclusion of certain grains. It is better to start with a restricted list of grains (a precautionary principle) and extend this as more knowledge becomes available. An exact definition of the raw materials (milled, cracked, crushed, rolled, or flaked) and knowledge of the components providing health effects would appear to be crucial issues for the European authorities when approving health claims. It is important that health claims are evidence-based, sustainable, and officially validated. PMID:20300475

Alteration of municipal and industrial slags under atmospheric conditions

NASA Astrophysics Data System (ADS)

Rafał Kowalski, Piotr; Michalik, Marek

2014-05-01

The Waste Management System in Poland is being consequently built since 1998. After important changes in legislation, local governments have taken over the duty of waste collection. New points of selective collection of wastes have been opened and new sorting and composting plants were built. The last stage of introducing the Waste Management System is construction of waste incineration power plants. From nine installations which were planned, six are now under construction and they will start operating within the next two years. It is assumed that the consumption of raw wastes for these installations will reach 974 thousand tons per year. These investments will result in increased slags and ashes production. Now in Poland several local waste incinerators are operating and predominant amount of produced incineration residues is landfilled. These materials are exposed to atmospheric conditions in time of short term storage (just after incineration) and afterwards for a longer period of time on the landfill site. During the storage of slags low temperature mineral transformations and chemical changes may occur and also some components can be washed out. These materials are stored wet because of the technological processes. The aim of this study is to investigate the influence of storage in atmospheric conditions on slags from incineration of industrial and municipal wastes. The experiment started in January 2013. During this period slag samples from incineration of industrial and municipal wastes were exposed to atmospheric conditions. Samples were collected after 6 and 12 months. Within this time the pH value was measured monthly, and during the experimental period remained constant on the level of 9.5. After 6 months of exposure only slight changes in mineral compositions were observed in slags. The results of XRD analysis of municipal slags showed increase in content of carbonate minerals in comparison to the raw slag samples. In industrial slags, a decrease in content of soluble minerals, like halite, in comparison to the output samples was noted. These phases where probably dissolved and washed out from the samples. After 12 months of atmospheric exposure in municipal slags only slight changes in weight (1 wt%) were observed, whereas in industrial slags slightly above 10 wt% of the material was removed. After 12 months of atmospheric exposure more significant changes are expected such as changes in chemical and mineral compositions and changes in heavy metals and toxic elements concentrations due to leaching.

TanDEM-X calibrated Raw DEM generation

NASA Astrophysics Data System (ADS)

Rossi, Cristian; Rodriguez Gonzalez, Fernando; Fritz, Thomas; Yague-Martinez, Nestor; Eineder, Michael

2012-09-01

The TanDEM-X mission successfully started on June 21st 2010 with the launch of the German radar satellite TDX, placed in orbit in close formation with the TerraSAR-X (TSX) satellite, and establishing the first spaceborne bistatic interferometer. The processing of SAR raw data to the Raw DEM is performed by one single processor, the Integrated TanDEM-X Processor (ITP). The quality of the Raw DEM is a fundamental parameter for the mission planning. In this paper, a novel quality indicator is derived. It is based on the comparison of the interferometric measure, the unwrapped phase, and the stereo-radargrammetric measure, the geometrical shifts computed in the coregistration stage. By stating the accuracy of the unwrapped phase, it constitutes a useful parameter for the determination of problematic scenes, which will be resubmitted to the dual baseline phase unwrapping processing chain for the mitigation of phase unwrapping errors. The stereo-radargrammetric measure is also operationally used for the Raw DEM absolute calibration through an accurate estimation of the absolute phase offset. This paper examines the interferometric algorithms implemented for the operational TanDEM-X Raw DEM generation, focusing particularly on its quality assessment and its calibration.

Thermal Curing Process Monitoring of the Composite Material Using the FBG sensor

NASA Astrophysics Data System (ADS)

Zhang, Youhong; Chang, Xinlong; Zhang, Xiaojun; He, Xiangyong

2018-03-01

The raw composite material will suffer complex chemical and morphological changes during the thermal curing process, and it is difficult to monitor the curing process and curing effect. In this paper, the FBG sensor was embedded in the raw composite material to monitor the whole curing process. The experiment results showed that the FBG sensor can monitor the resin transformation and residual deformation of the composite material, and the FBG sensor can be applied to monitor the thermal curing process of the composite structure.

Analysis of waste coal from the enterprises of Kemerovo region as raw materials for production of ceramic materials

NASA Astrophysics Data System (ADS)

Stolboushkin, A. Yu; Akst, D. V.; Fomina, O. A.; Ivanov, A. I.; Syromyasov, V. A.

2017-09-01

The analysis of waste coal from mining enterprises of Kemerovo region as raw materials for production of building ceramics is given. The results of studies of material, chemical and mineralogical compositions of waste coal from Abashevskaya processing plant (Novokuznetsk) are presented. It was established that the chemical composition of waste coal refers to aluminosilicate raw materials with a high content of alumina and coloring oxides, the residual carbon content in the wastes is 12-25 %. According to the granulometric composition the waste coal is basically a sandy-dusty fraction with a small amount of clay particles (1-3 %). Additional grinding of coal waste and the introduction of a clay additive in an amount of up to 30 % are recommended. The results of the study of the mineral composition of waste coal are presented. Clay minerals are represented in the descending order by hydromuscovite, montmorillonite and kaolinite, minerals-impurities consist of quartz, feldspar fine-dispersed carbonates. The results of the investigation of ceramic-technological properties of waste coal, which belong to the group of moderately plastic low-melting raw materials, are given. As a result of a comprehensive study it was been established that with chemical, granulometric and mineralogical compositions waste coal with the reduced residual carbon can be used in the production of ceramic bricks.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Ching-Fong; Pokharel, Reeju; Brand, Michael J.

Here, we developed a copper/tungsten (Cu/W) composite for mesoscale Materials Science applications using the novel High-Energy Diffraction Microscopy (HEDM) technique. Argon-atomized copper powder was selected as the starting raw powder and screened to remove the extremely large particle fraction. Tungsten particles were collected by milling and screening the -325 mesh tungsten powder between 500 and 635 mesh sieves. Hot pressing of screened Cu powder was performed at 900 °C in Ar/4 %H 2 atmosphere. XRD and ICP results show that the hot-pressed Cu sample consists of about 5 vol% Cu 2O, which is caused by the presence of oxygen onmore » the surface of the starting Cu powder. Hot pressing the copper powder in a pure hydrogen atmosphere was successful in removing most of the surface oxygen. Our process was also implemented for hot pressing the Cu/W composite. The density of the Cu/W composites hot pressed at 950 °C in pure hydrogen was about 94 % of the theoretical density (TD). The hot-pressed Cu/W composites were further hot isostatic pressed at 1050 °C in argon atmosphere, which results in 99.6 % of the TD with the designed Cu grain size and W particle distribution. Tensile specimens with D-notch were machined using the wire EDM method. Furthermore, the processing and consolidation of these materials will be discussed in detail. The HEDM images are also showed and discussed.« less

Lunar mineral feedstocks from rocks and soils: X-ray digital imaging in resource evaluation

NASA Technical Reports Server (NTRS)

Chambers, John G.; Patchen, Allan; Taylor, Lawrence A.; Higgins, Stefan J.; Mckay, David S.

1994-01-01

The rocks and soils of the Moon provide raw materials essential to the successful establishment of a lunar base. Efficient exploitation of these resources requires accurate characterization of mineral abundances, sizes/shapes, and association of 'ore' and 'gangue' phases, as well as the technology to generate high-yield/high-grade feedstocks. Only recently have x-ray mapping and digital imaging techniques been applied to lunar resource evaluation. The topics covered include inherent differences between lunar basalts and soils and quantitative comparison of rock-derived and soil-derived ilmenite concentrates. It is concluded that x-ray digital-imaging characterization of lunar raw materials provides a quantitative comparison that is unattainable by traditional petrographic techniques. These data are necessary for accurately determining mineral distributions of soil and crushed rock material. Application of these techniques will provide an important link to choosing the best raw material for mineral beneficiation.

7 CFR 58.430 - Milk.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Material § 58... milk used. Such dairy products shall have originated from raw milk meeting the same requirements as...

7 CFR 58.430 - Milk.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Material § 58... milk used. Such dairy products shall have originated from raw milk meeting the same requirements as...

Non-Formal Education in Ethiopia: The Modern Sector. Program of Studies in Non-Formal Education. Discussion Papers. No. 6.

ERIC Educational Resources Information Center

Niehoff, Richard O.; Wilder, Bernard

Nonformal education programs operating in the modern sector in Ethiopia are described in a perspective relevant to the Ethiopian context. The modern sector is defined as those activities concerned with the manufacture of goods, extraction of raw materials, the processing of raw materials, the provision of services, and the creation and maintenance…

40 CFR 418.52 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2012 CFR

2012-07-01

... from nitric acid production in which all the raw material ammonia is in the gaseous form: [Metric units... limitations Maximum for any 1 day Average of daily values for 30 consecutive days shall not exceed— Ammonia... all the raw material ammonia is in the shipped liquid form: [Metric units, kg/kkg of product; English...

40 CFR 418.52 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... from nitric acid production in which all the raw material ammonia is in the gaseous form: [Metric units... limitations Maximum for any 1 day Average of daily values for 30 consecutive days shall not exceed— Ammonia... all the raw material ammonia is in the shipped liquid form: [Metric units, kg/kkg of product; English...

40 CFR 418.52 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2014 CFR

2014-07-01

... from nitric acid production in which all the raw material ammonia is in the gaseous form: [Metric units... limitations Maximum for any 1 day Average of daily values for 30 consecutive days shall not exceed— Ammonia... all the raw material ammonia is in the shipped liquid form: [Metric units, kg/kkg of product; English...

40 CFR 418.52 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... from nitric acid production in which all the raw material ammonia is in the gaseous form: [Metric units... limitations Maximum for any 1 day Average of daily values for 30 consecutive days shall not exceed— Ammonia... all the raw material ammonia is in the shipped liquid form: [Metric units, kg/kkg of product; English...

40 CFR 418.52 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... from nitric acid production in which all the raw material ammonia is in the gaseous form: [Metric units... limitations Maximum for any 1 day Average of daily values for 30 consecutive days shall not exceed— Ammonia... all the raw material ammonia is in the shipped liquid form: [Metric units, kg/kkg of product; English...

Catalysis: A Potential Alternative to Kraft Pulping

Treesearch

Alan W. Rudie; Peter W. Hart

2014-01-01

A thorough analysis of the kraft pulping process makes it obvious why it has dominated for over a century as an industrial process with no replacement in sight. It uses low cost raw materials, collects and regenerates over 90% of the chemicals needed in the process, is indifferent to wood raw material and good at preserving the cellulose portion of the wood which is...

Catalysis: A Potential Alternative to Kraft Pulping

Treesearch

Alan W. Rudie; Peter W. Hart

2014-01-01

A thorough analysis of the kraft pulping process makes it obvious why it has dominated for over a century as an industrial process with no replacement in sight. It uses low-cost raw materials; collects and regenerates over 90% of the chemicals needed in the process; and is indifferent to wood raw material and good at preserving the cellulose portion of the wood, the...

Pulpwood production in the Northeast 1969

Treesearch

James T. Bones; David R. Dickson

1970-01-01

This annual report is based on a canvass of all pulpmills in the Northeast that use wood-either from roundwood or plant residues-as a basic raw material for a variety of products. Mills that use pulpwood as a raw material in producing insulation board and hardboard were also included in the canvass. The production-from-roundwood statistics reported in this bulletin are...

Pulpwood production in the Northeast 1970

Treesearch

James T. Bones; David R. Dickson

1971-01-01

This annual report is based on a canvass of all pulpmills in the Northeast that use wood-either roundwood or plant residues-as a basic raw material for a variety of products. Mills that use pulpwood as a raw material in producing insulation board and hardboard were also included in the canvass. The statistics for production from roundwood reported in this bulletin are...

2. EXTERIOR VIEW, LOOKING NORTHEAST FROM THE CUPOLA (RIGHT) TO ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. EXTERIOR VIEW, LOOKING NORTHEAST FROM THE CUPOLA (RIGHT) TO COKE BIN (LEFT), OF RAW MATERIALS YARD. FOUNDRY IRON IS FROM SCRAP, NOT BASIC ORE. RAW MATERIALS ASSEMBLED, IN PILES, FOR SMELTING ARE AUTOMOTIVE SCRAP (CENTER), STRUCTURAL STEEL AND RAILROAD RAIL (RIGHT) AND LIMESTONE (LEFT). - Stockham Pipe & Fittings Company, Grey Iron Foundry, 4000 Tenth Avenue North, Birmingham, Jefferson County, AL

Successes, shortcomings in using production wastes as raw material

NASA Astrophysics Data System (ADS)

Glushenkova, L.

1983-10-01

The economical and rational use of all forms of resources under modern conditions is a task of nationwide significance. Its urgency is caused by factors such as the progressively growing need for raw material, fuel, energy, and supplies, the limited and non-renewable nature of many minerals, and the difficult conditions of mining them and transporting them to where they are needed.

Strategy to Overcome Effect of Raw Materials on Enzymatic Process of Biodiesel from Non-edible Oils Using Candida sp. 99-125 Lipase.

PubMed

Nie, Kaili; Wang, Fang; Tan, Tianwei; Liu, Luo

2015-11-01

Non-edible oils are preferred raw materials for biodiesel production. However, the properties of raw materials significantly affect the synthesis process, leading to difficulties to design one process suitable for any kind of raw material. In this study, the composition of five typical non-edible oils was analyzed. The major difference was the content of free fatty acids, reflected from their acid values. The influence of different oils was investigated by using lipase from Candida sp. 99-125. At low lipase dosage and low water content, the conversion was found proportional to the acid value. However, by increasing the water content or lipase dosage, we observed that the conversions for all kinds of oils used in this study could exceed 80%. Time course analysis indicates that the lipase used in this study catalyzed hydrolysis followed by esterification, rather than direct transesterification. Accumulation of free fatty acids at the very beginning was necessary. A high water content facilitated the hydrolysis of oils with low acid value. This lipase showed capability to transform all the oils by controlling the water content.

Industrial bioconversion of renewable resources as an alternative to conventional chemistry.

PubMed

Willke, Th; Vorlop, K-D

2004-12-01

There are numerous possibilities for replacing chemical techniques with biotechnological methods based on renewable resources. The potential of biotechnology (products, technologies, metabolic pathways) is for the most part well known. Often the costs are still the problem. Biotechnological advances have the best chances for replacing some fine chemicals. While the raw material costs are less of a consideration here, the environmental benefit is huge, as chemical-technical processes often produce a wide range of undesirable/harmful by-products or waste. In the case of bulk chemicals (<1 US dollar/kg) the product price is affected mainly by raw material costs. As long as fossil raw materials are still relatively inexpensive, alternatives based on renewable resources cannot establish themselves. Residues and waste, which are available even at no cost in some cases, are an exception. The introduction of new technologies for the efficient use of such raw materials is currently being promoted. The utilisation of residual wood, plant parts, waste fat, and crude glycerol, for example, provides great potential. For industrial chemicals (2-4 US dollars/kg), process and recovery costs play a greater role. Here, innovative production technologies and product recovery techniques (e.g. on-line product separation) can increase competitiveness.

Optimization of formulation and processing of Moringa oleifera and spirulina complex tablets.

PubMed

Zheng, Yi; Zhu, Fan; Lin, Dan; Wu, Jun; Zhou, Yichao; Mark, Bohn

2017-01-01

Objective: To prepare a more comprehensive nutrition, more balanced proportion of natural nutritional supplement tablets with Moringa oleifera leaves and spirulina the two nutrients which have complementary natural food ingredients. Method: On the basis of research M. oleifera leaves with spirulina nutrient composition was determined on M. oleifera leaves and spirulina ratio of raw materials, and the choice of microcrystalline cellulose, sodium salt of caboxy methyl cellulose(CMC),magnesium stearate excipient, through single factor and orthogonal experiment, selecting the best formula tablets prepared by powder direct compression technology, for preparation of M. oleifera and spirulina complex tablets. Results: The best ratio of raw material for the M. oleifera leaves powder: spirulina powder was 7:3, the best raw materials for the tablet formulation was 88.5%, 8.0% microcrystalline cellulose, CMC 2.0%, stearin magnesium 1.5%, the optimum parameters for the raw material crushing 200-300 mesh particle size, moisture content of 7%, tableting pressure 40 kN. Conclusion: Through formulation and process optimization, we can prepare more comprehensive and balanced nutrition M. oleifera and spirulina complex tablets, its sheet-shaped appearance, piece weight variation, hardness, friability, disintegration and other indicators have reached the appropriate quality requirements.

Effect of synthesis route on electrical and ethanol sensing characteristics for LaFeO3-δ nanoparticles by citric sol-gel method

NASA Astrophysics Data System (ADS)

Cao, Ensi; Yang, Yuqing; Cui, Tingting; Zhang, Yongjia; Hao, Wentao; Sun, Li; Peng, Hua; Deng, Xiao

2017-01-01

LaFeO3-δ nanoparticles were prepared by citric sol-gel method with different raw material choosing and calcination process. The choosing of polyethylene glycol instead of ethylene glycol as raw material and additional pre-calcination at 400 °C rather than direct calcination at 600 °C could result in the decrease of resistance due to the reduction of activation energy Ea. Meanwhile, the choosing of ethylene glycol as raw material and additional pre-calcination leads to the enhancement of sensitivity to ethanol. Comprehensive analysis on the sensitivity and XRD, SEM, TEM, XPS results indicates that the sensing performance of LaFeO3-δ should be mainly determined by the adsorbed oxygen species on Fe ions, with certain contribution from native active oxygen. The best sensitivity of 46.1-200 ppm ethanol at prime working temperature of 112 °C is obtained by the sample using ethylene glycol as raw material with additional pre-calcination, which originates from its uniformly-sized and well-dispersed particles as well as high atomic ratio of Fe/La at surface region.

Efficient sugar release by acetic acid ethanol-based organosolv pretreatment and enzymatic saccharification.

PubMed

Zhang, Hongdan; Wu, Shubin

2014-12-03

Acetic acid ethanol-based organosolv pretreatment of sugar cane bagasse was performed to enhance enzymatic hydrolysis. The effect of different parameters (including temperature, reaction time, solvent concentration, and acid catalyst dose) on pretreatment prehydrolyzate and subsequent enzymatic digestibility was determined. During the pretreatment process, 11.83 g of xylose based on 100 g of raw material could be obtained. After the ethanol-based pretreatment, the enzymatic hydrolysis was enhanced and the highest glucose yield of 40.99 g based on 100 g of raw material could be obtained, representing 93.8% of glucose in sugar cane bagasse. The maximum total sugar yields occurred at 190 °C, 45 min, 60:40 ethanol/water, and 5% dosage of acetic acid, reaching 58.36 g (including 17.69 g of xylose and 40.67 g of glucose) based on 100 g of raw material, representing 85.4% of total sugars in raw material. Furthermore, characterization of the pretreated sugar cane bagasse using X-ray diffraction and scanning electron microscopy analyses were also developed. The results suggested that ethanol-based organosolv pretreatment could enhance enzymatic digestibilities because of the delignification and removal of xylan.

Environmental analysis of raw cork extraction in cork oak forests in southern Europe (Catalonia--Spain).

PubMed

Rives, Jesús; Fernandez-Rodriguez, Ivan; Rieradevall, Joan; Gabarrell, Xavier

2012-11-15

Cork oak grows endemically in a narrow region bordering the western Mediterranean, and especially in the Iberian Peninsula. The importance of cork agro-forestry systems lies in the fact that a natural and renewable raw material - cork - can be extracted sustainably without endangering the tree or affecting biodiversity. This paper describes an environmental analysis of the extraction of raw cork in cork oak forests in Catalonia, using data from five representative local forest exploitations. The evaluation was carried out using life cycle assessment (LCA) methodology, and all the forestry management required to obtain a tonne of raw cork was included. The aim of the study was to evaluate the environmental impacts - in terms of global warming, acidification, eutrophication, human toxicity, and so on - caused by cork extraction and determine the carbon dioxide balance of these forestry systems, with a tree lifespan of about 200 years. During the life cycle extraction of cork in Catalonia, 0.2 kg of CO(2) eq. was emitted per kg of raw cork extracted. Moreover, cork cannot be extracted without the tree, which will be fixing carbon dioxide throughout its technological useful life (200 years), despite the fact that the bark is removed periodically: every 13-14 years. If the emission from extraction and the carbon contained in the material is discounted, the carbon dioxide balance indicates that 18 kg of CO(2) are fixed per kg of raw cork extracted. Therefore, cork is a natural, renewable and local material that can replace other non-renewable materials, at local level, to reduce the environmental impacts of products, and particularly to reduce their carbon footprint. Copyright © 2012 Elsevier Ltd. All rights reserved.

Optical and spectroscopic characterizations of Algerian silica raw material to predict high quality solar-grade silicon

NASA Astrophysics Data System (ADS)

Kheloufi, A.; Bobocioiu, E.; Kerkar, F.; Kefaifi, A.; Anas, S.; Medjahed, S. A.; Belkacem, Y.; Keffous, A.

2017-03-01

We assess the potential use as raw material for photovoltaics of Algerian silica samples from the quartz veins of the Tirek deposit and quartz sandstones of the Ain Barda deposit. With 97-98% purity, they all require enrichment before their industrial utilization. Acid leaching and gravimetric separation are used to remove the impurities at the grain boundaries and within the crystal lattice. We obtain course, middle, and fine products. The acid leaching process and the gravimetric separation increase the content of SiO2 up to 99.68%; the residue concentration of iron, alumina and zirconium is decreased to 70, 72 and 58 ppm respectively. These values are in agreement with requirements for silica as raw material destined for solar-grade silicon production.

Agaves as a raw material: recent technologies and applications.

PubMed

Narváez-Zapata, J A; Sánchez-Teyer, L F

2009-01-01

Agave plants are a valuable source of raw material due to its fibrous and complex sugar content of their leaves and core, and their bagasse waste can be use for several aims. This plant genus belongs to the Agavaceae family and until now more than 200 species have been described. A large number of Agave species are currently used as raw material in several biotechnological processes. This review shows the reported applications and patents on fields like alcoholic brewages with special reference to Tequila and Mezcal, the isolation and use of compounds such as saponins and agave fructans, and their potential biotechnological application on several human demands. The process to obtain fibers and cellulose, stock feeds, and several miscellaneous extractives are also reviewed. Some possibilities and problems of cultivation are discussed.

Optical-electronic system for express analysis of mineral raw materials dressability by color sorting method

NASA Astrophysics Data System (ADS)

Alekhin, Artem A.; Gorbunova, Elena V.; Chertov, Aleksandr N.; Petuhova, Darya B.

2013-04-01

Due to the depletion of solid minerals ore reserves and the involvement in the production of the poor and refractory ores a process of continuous appreciation of minerals is going. In present time at the market of enrichment equipment are well represented optical sorters of various firms. All these sorters are essentially different from each other by parameters of productivity, classes of particles sizes for processed raw, nuances of decision algorithm, as well as by color model (RGB, YUV, HSB, etc.) chosen to describe the color of separating mineral samples. At the same time there is no dressability estimation method for mineral raw materials without direct semi-industrial test on the existing type of optical sorter, as well as there is no equipment realizing mentioned dressability estimation method. It should also be note the lack of criteria for choosing of one or another manufacturer (or type) of optical sorter. A direct consequence of this situation is the "opacity" of the color sorting method and the rejection of its potential customers. The proposed solution of mentioned problems is to develop the dressability estimation method, and to create an optical-electronic system for express analysis of mineral raw materials dressability by color sorting method. This paper has the description of structure organization and operating principles of experimental model optical-electronic system for express analysis of mineral raw material. Also in this work are represented comparison results of the proposed optical-electronic system and the real color sorter.

7 CFR 58.232 - Milk.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Materials § 58.232 Milk. Raw milk shall meet the requirements as outlined in §§ 58.132 through 58.138 and, unless...

7 CFR 58.232 - Milk.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Materials § 58.232 Milk. Raw milk shall meet the requirements as outlined in §§ 58.132 through 58.138 and, unless...

40 CFR 409.21 - Specialized definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Crystalline Cane Sugar Refining Subcategory § 409... raw material (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

Extraterrestrial materials processing and construction

NASA Technical Reports Server (NTRS)

Criswell, D. R.

1978-01-01

Applications of available terrestrial skills to the gathering of lunar materials and the processing of raw lunar materials into industrial feed stock were investigated. The literature on lunar soils and rocks was reviewed and the chemical processes by which major oxides and chemical elements can be extracted were identified. The gathering of lunar soil by means of excavation equipment was studied in terms of terrestrial experience with strip mining operations on earth. The application of electrostatic benefication techniques was examined for use on the moon to minimize the quantity of materials requiring surface transport and to optimize the stream of raw materials to be transported off the moon for subsequent industrial use.

[Russian and foreign legal-standards bases for guaranteeing the parasitic safety of raw produce and food products].

PubMed

Lovgalev, A S

1998-01-01

The paper analyzes the standard legal and methodological assurance of the quality and safety of animal food raw materials and foodstuffs (meat, meat products, fish, shellfish, crayfish and their processing products) by the parasitic purity rates according the requirements under the Russian Federation's laws "On Sanitary and Epidemiological Well-Being of the Population", "On Protection of Consumer's Rights", "On Certification of Products and Services", those of SanPiN, such as 2.3.2.560-96 "Sanitary Requirements for the Quality and Safety of Food Raw Materials and Foodstuffs" and 3.2.569-96 "Prevention of Parasitic Diseases in the Russian Federation".

Comparative analysis of non-destructive methods to control fissile materials in large-size containers

NASA Astrophysics Data System (ADS)

Batyaev, V. F.; Sklyarov, S. V.

2017-09-01

The analysis of various non-destructive methods to control fissile materials (FM) in large-size containers filled with radioactive waste (RAW) has been carried out. The difficulty of applying passive gamma-neutron monitoring FM in large containers filled with concreted RAW is shown. Selection of an active non-destructive assay technique depends on the container contents; and in case of a concrete or iron matrix with very low activity and low activity RAW the neutron radiation method appears to be more preferable as compared with the photonuclear one. Note to the reader: the pdf file has been changed on September 22, 2017.

JPRS Report East Asia Southeast Asia

DTIC Science & Technology

1987-06-03

the Philippines and Japan experienced production problems. The Philippines lacked supplies of raw materials while Japan’s currency rose so high as...Malaysia, Saudi Arabia, Singapore Squid: Greece, Spain, the Philippines , Saudi Arabia, U.S. Clams: U.S., Canada, Malaysia, Japan, Italy, West Germany...raw material caught under joint venture fisheries enter- prises, while Thailand’s competitors like the Philippines and Taiwan remain unable to

Effect of the raw material composition of fabrics on the Limiting Oxygen Index (LOI)

NASA Technical Reports Server (NTRS)

Jeler, S.; Ceric, B.

1986-01-01

The raw material composition of fabrics is one of the most important factors for LOI value. LOI value was determined in samples of varying composition composed of cellulose, protein, and synthetic fibers and their mixtures, based on ASTM D 2863-76. Cellulose fibers and their mixtures exhibited the lowest value, while synthetic fibers had the highest LOI value.

JPRS Report, Near East and South Asia, India

DTIC Science & Technology

1992-05-13

withdrawal of the RBI import policy for capital goods, raw materials, compo- nents and industrial consumables . Also, the licensing of host of industrial ...fully capable of establishing consumer production industries and providing raw materials for it. This would also benefit India, because a huge market...which two- thirds of population depends for their livelihood, demand base for the industrial sector, especially essen- tial consumer goods is likely

Hook tool manufacture in New Caledonian crows: behavioural variation and the influence of raw materials.

PubMed

Klump, Barbara C; Sugasawa, Shoko; St Clair, James J H; Rutz, Christian

2015-11-18

New Caledonian crows use a range of foraging tools, and are the only non-human species known to craft hooks. Based on a small number of observations, their manufacture of hooked stick tools has previously been described as a complex, multi-stage process. Tool behaviour is shaped by genetic predispositions, individual and social learning, and/or ecological influences, but disentangling the relative contributions of these factors remains a major research challenge. The properties of raw materials are an obvious, but largely overlooked, source of variation in tool-manufacture behaviour. We conducted experiments with wild-caught New Caledonian crows, to assess variation in their hooked stick tool making, and to investigate how raw-material properties affect the manufacture process. In Experiment 1, we showed that New Caledonian crows' manufacture of hooked stick tools can be much more variable than previously thought (85 tools by 18 subjects), and can involve two newly-discovered behaviours: 'pulling' for detaching stems and bending of the tool shaft. Crows' tool manufactures varied significantly: in the number of different action types employed; in the time spent processing the hook and bending the tool shaft; and in the structure of processing sequences. In Experiment 2, we examined the interaction of crows with raw materials of different properties, using a novel paradigm that enabled us to determine subjects' rank-ordered preferences (42 tools by 7 subjects). Plant properties influenced: the order in which crows selected stems; whether a hooked tool was manufactured; the time required to release a basic tool; and, possibly, the release technique, the number of behavioural actions, and aspects of processing behaviour. Results from Experiment 2 suggested that at least part of the natural behavioural variation observed in Experiment 1 is due to the effect of raw-material properties. Our discovery of novel manufacture behaviours indicates a plausible scenario for the evolutionary origins, and gradual refinement, of New Caledonian crows' hooked stick tool making. Furthermore, our experimental demonstration of a link between raw-material properties and aspects of tool manufacture provides an alternative hypothesis for explaining regional differences in tool behaviours observed in New Caledonian crows, and some primate species.

Characterization of mammalian cell culture raw materials by combining spectroscopy and chemometrics

PubMed Central

Trunfio, Nicholas; Lee, Haewoo; Starkey, Jason; Agarabi, Cyrus; Liu, Jay

2017-01-01

Two of the primary issues with characterizing the variability of raw materials used in mammalian cell culture, such as wheat hydrolysate, is that the analyses of these materials can be time consuming, and the results of the analyses are not straightforward to interpret. To solve these issues, spectroscopy can be combined with chemometrics to provide a quick, robust and easy to understand methodology for the characterization of raw materials; which will improve cell culture performance by providing an assessment of the impact that a given raw material will have on final product quality. In this study, four spectroscopic technologies: near infrared spectroscopy, middle infrared spectroscopy, Raman spectroscopy, and fluorescence spectroscopy were used in conjunction with principal component analysis to characterize the variability of wheat hydrolysates, and to provide evidence that the classification of good and bad lots of raw material is possible. Then, the same spectroscopic platforms are combined with partial least squares regressions to quantitatively predict two cell culture critical quality attributes (CQA): integrated viable cell density and IgG titer. The results showed that near infrared (NIR) spectroscopy and fluorescence spectroscopy are capable of characterizing the wheat hydrolysate's chemical structure, with NIR performing slightly better; and that they can be used to estimate the raw materials’ impact on the CQAs. These results were justified by demonstrating that of all the components present in the wheat hydrolysates, six amino acids: arginine, glycine, phenylalanine, tyrosine, isoleucine and threonine; and five trace elements: copper, phosphorus, molybdenum, arsenic and aluminum, had a large, statistically significant effect on the CQAs, and that NIR and fluorescence spectroscopy performed the best for characterizing the important amino acids. It was also found that the trace elements of interest were not characterized well by any of the spectral technologies used; however, the trace elements were also shown to have a less significant effect on the CQAs than the amino acids. © 2017 The Authors Biotechnology Progress published by Wiley Periodicals, Inc. on behalf of American Institute of Chemical Engineers, 33:1127–1138, 2017 PMID:28393480

Phenotyping the quality of complex medium components by simple online-monitored shake flask experiments.

PubMed

Diederichs, Sylvia; Korona, Anna; Staaden, Antje; Kroutil, Wolfgang; Honda, Kohsuke; Ohtake, Hisao; Büchs, Jochen

2014-11-07

Media containing yeast extracts and other complex raw materials are widely used for the cultivation of microorganisms. However, variations in the specific nutrient composition can occur, due to differences in the complex raw material ingredients and in the production of these components. These lot-to-lot variations can affect growth rate, product yield and product quality in laboratory investigations and biopharmaceutical production processes. In the FDA's Process Analytical Technology (PAT) initiative, the control and assessment of the quality of critical raw materials is one key aspect to maintain product quality and consistency. In this study, the Respiration Activity Monitoring System (RAMOS) was used to evaluate the impact of different yeast extracts and commercial complex auto-induction medium lots on metabolic activity and product yield of four recombinant Escherichia coli variants encoding different enzymes. Under non-induced conditions, the oxygen transfer rate (OTR) of E. coli was not affected by a variation of the supplemented yeast extract lot. The comparison of E. coli cultivations under induced conditions exhibited tremendous differences in OTR profiles and volumetric activity for all investigated yeast extract lots of different suppliers as well as lots of the same supplier independent of the E. coli variant. Cultivation in the commercial auto-induction medium lots revealed the same reproducible variations. In cultivations with parallel offline analysis, the highest volumetric activity was found at different cultivation times. Only by online monitoring of the cultures, a distinct cultivation phase (e.g. glycerol depletion) could be detected and chosen for comparable and reproducible offline analysis of the yield of functional product. This work proves that cultivations conducted in complex media may be prone to significant variation in final product quality and quantity if the quality of the raw material for medium preparation is not thoroughly checked. In this study, the RAMOS technique enabled a reliable and reproducible screening and phenotyping of complex raw material lots by online measurement of the respiration activity. Consequently, complex raw material lots can efficiently be assessed if the distinct effects on culture behavior and final product quality and quantity are visualized.

Zirconia-hydroxyapatite composite material with micro porous structure.

PubMed

Matsumoto, Takuya Junior; An, Sang-Hyun; Ishimoto, Takuya; Nakano, Takayoshi; Matsumoto, Takuya; Imazato, Satoshi

2011-11-01

Titanium plates and apatite blocks are commonly used for restoring large osseous defects in dental and orthopedic surgery. However, several cases of allergies against titanium have been recently reported. Also, sintered apatite block does not possess sufficient mechanical strength. In this study, we attempted to fabricate a composite material that has mechanical properties similar to biocortical bone and high bioaffinity by compounding hydroxyapatite (HAp) with the base material zirconia (ZrO(2)), which possesses high mechanical properties and low toxicity toward living organisms. After mixing the raw material powders at several different ZrO(2)/HAp mixing ratios, the material was compressed in a metal mold (8 mm in diameter) at 5 MPa. Subsequently, it was sintered for 5 h at 1500°C to obtain the ZrO(2)/HAp composite. The mechanical property and biocompatibility of materials were investigated. Furthermore, osteoconductivity of materials was investigated by animal studies. A composite material with a minute porous structure was successfully created using ZrO(2)/HAp powders, having different particle sizes, as the starting material. The material also showed high protein adsorption and a favorable cellular affinity. When the mixing ratio was ZrO(2)/HAp=70/30, the strength was equal to cortical bone. Furthermore, in vivo experiments confirmed its high osteoconductivity. The composite material had strength similar to biocortical bones with high cell and tissue affinities by compounding ZrO(2) and HAp. The ZrO(2)/HAp composite material having micro porous structure would be a promising bone restorative material. Copyright © 2011 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Air ionizer application for electrostatic discharge (ESD) dust removal in automotive painting industry

NASA Astrophysics Data System (ADS)

Yosri, M. H.; Muhamad, P.; Ismail, M. A.; Yatim, N. H. M.

2018-01-01

Dust and fiber have been identified among the highest contributor for the defect in automotive painting line with range from 40% to 50% of total defect breakdown. Eventually, those defects will effect on both visual appearance and also the performance of the parts. In addition, the significance of controlling dust in an assembly line is crucial in order to maintain the quality of the product, part performance yield and effect on workers’ health [1]. By considering the principle and technology applied in electronic clean room technology, the ionizer have been introduce to control dust contamination in automotive painting line. The first auto maker industry whom found the effectiveness of the clean room application to reduce the defect and production line downtime was Chrysler [2]. By doing so, it’s allowed the transmission plant to offer 50 000 mile guarantee on the transmission systems. The main objective of this research is to verify the effectiveness of ionizer device in order to reduce the rejection contribute by dust and fiber particle in the automotive painting line. Towards the main objective, a few sub areas will be explored, as a supporting factor to ensure the result gain from this study is solid and constructive. The experiment start by verifying the electrostatic value of the raw material (substrate) before and after the ionizer treatment. From here the correlation of the electrostatic value generated by the raw material that effect to production pass rate can be explored. At the meantime, the performance of the production pass rate after the ionizer treatment which related to the painted surface area can be determined.

MOLA II Laser Transmitter Calibration and Performance. 1.2

NASA Technical Reports Server (NTRS)

Afzal, Robert S.; Smith, David E. (Technical Monitor)

1997-01-01

The goal of the document is to explain the algorithm for determining the laser output energy from the telemetry data within the return packets from MOLA II. A simple algorithm is developed to convert the raw start detector data into laser energy, measured in millijoules. This conversion is dependent on three variables, start detector counts, array heat sink temperature and start detector temperature. All these values are contained within the return packets. The conversion is applied to the GSFC Thermal Vacuum data as well as the in-space data to date and shows good correlation.

Effect of microbial activities on stored raw buffalo hide.

PubMed

Shede, P N; Kanekar, P P; Polkade, A V; Sarnaik, S S; Dhakephalkar, P K; Chiplonkar, S A; Nilegaonkar, S S

2009-11-01

'Keeping qualities' of hides are dependent on the total microbial flora associated with the hides and the biochemical changes brought about by these microorganisms during short-term storage at ambient temperature (28 +/- 2 degrees C). It was evident that within first 24 hr of hide's ambient storage, bacterial load was raised to 8.8 log cfu g(-1) hide from 6.1 log cfu g(-1) hide. Nonlinear parabolic increase in release of hydroxyproline and tyrosine from stored hide was observed starting from 0 hr and confirming proteolytic activities. Continuous release of CO2 from the stored hide suggested its mineralization. Exponential release of free fatty acids during storage indicated simultaneous lipolysis. Thus the process of biodegradation during the course of ambient storage of hide piece was found to progress steadily and seems to be interrelated as well as very complex. During the storage period, the liquefaction of hide piece was also observed visually within 96 hr. Present studies of assessment of bacterial activities on hide with respect to total bacterial load, release of amino acids, free fatty acids and evolved CO2 provide data that can be used to formulate and evaluate hide curing agent(s) other than salt, thus rendering leather industry a platform to design bio-based technologies for efficient and ecofriendly preservation of raw materials.

Utilization of flotation wastes of copper slag as raw material in cement production.

PubMed

Alp, I; Deveci, H; Süngün, H

2008-11-30

Copper slag wastes, even if treated via processes such as flotation for metal recovery, still contain heavy metals with hazardous properties posing environmental risks for disposal. This study reports the potential use of flotation waste of a copper slag (FWCS) as iron source in the production of Portland cement clinker. The FWCS appears a suitable raw material as iron source containing >59% Fe(2)O(3) mainly in the form of fayalite (Fe(2)SiO(4)) and magnetite (Fe(3)O(4)). The clinker products obtained using the FWCS from the industrial scale trial operations over a 4-month period were characterised for the conformity of its chemical composition and the physico-mechanical performance of the resultant cement products was evaluated. The data collected for the clinker products produced using an iron ore, which is currently used as the cement raw material were also included for comparison. The results have shown that the chemical compositions of all the clinker products including those of FWCS are typical of a Portland cement clinker. The mechanical performance of the standard mortars prepared from the FWCS clinkers were found to be similar to those from the iron ore clinkers with the desired specifications for the industrial cements e.g. CEM I type cements. Furthermore, the leachability tests (TCLP and SPLP) have revealed that the mortar samples obtained from the FWCS clinkers present no environmental problems while the FWCS could act as the potential source of heavy metal contamination. These findings suggest that flotation wastes of copper slag (FWCS) can be readily utilised as cement raw material due to its availability in large quantities at low cost with the further significant benefits for waste management/environmental practices of the FWCS and the reduced production and processing costs for cement raw materials.

Identifying Major Transitions in the Evolution of Lithic Cutting Edge Production Rates

PubMed Central

Clarkson, Chris

2016-01-01

The notion that the evolution of core reduction strategies involved increasing efficiency in cutting edge production is prevalent in narratives of hominin technological evolution. Yet a number of studies comparing two different knapping technologies have found no significant differences in edge production. Using digital analysis methods we present an investigation of raw material efficiency in eight core technologies broadly representative of the long-term evolution of lithic technology. These are bipolar, multiplatform, discoidal, biface, Levallois, prismatic blade, punch blade and pressure blade production. Raw material efficiency is assessed by the ratio of cutting edge length to original core mass. We also examine which flake attributes contribute to maximising raw material efficiency, as well as compare the difference between expert and intermediate knappers in terms of cutting edge produced per gram of core. We identify a gradual increase in raw material efficiency over the broad sweep of lithic technological evolution. The results indicate that the most significant transition in efficiency likely took place with the introduction of small foliate biface, Levallois and prismatic blade knapping, all introduced in the Middle Stone Age / Middle Palaeolithic among early Homo sapiens and Neanderthals. This suggests that no difference in raw material efficiency existed between these species. With prismatic blade technology securely dated to the Middle Palaeolithic, by including the more recent punch and pressure blade technology our results dispel the notion that the transition to the Upper Palaeolithic was accompanied by an increase in efficiency. However, further increases in cutting edge efficiency are evident, with pressure blades possessing the highest efficiency in this study, indicating that late/epi-Palaeolithic and Neolithic blade technologies further increased efficiency. PMID:27936135

Incidence, populations and diversity of fungi from raw materials, final products and air of processing environment of multigrain whole meal bread.

PubMed

Santos, Juliana Lane Paixão Dos; Bernardi, Angélica Olivier; Pozza Morassi, Letícia L; Silva, Beatriz S; Copetti, Marina Venturini; S Sant'Ana, Anderson

2016-09-01

This study aimed to assess the incidence, to quantify and to assess the diversity of fungi in a multigrain whole meal bread processing plant. Two hundred and eight one (n=281) samples were analyzed, including raw materials (n=120), air samples (n=136) and multigrain breads (n=25). Among the raw materials, the whole corn flour showed the highest counts of fungi (4.8logCFU/g), followed by whole-wheat flour (3.1logCFU/g). The counts of fungi in the air of processing environment were higher in post-baking steps (oven output, cooling, slicing, packaging) than in pre-baking steps (weighing and mixer) (p<0.05). Species of fungi isolated from spoiled bread samples stored at 5, 20, 25 and 30, and 40°C corresponded mostly to Penicillium paneum and Penicillium polonicum isolated from 20 and 24% of samples, respectively. These species were also isolated from raw materials (P. paneum and P. polonicum) and air collected at different processing sampling points (P. polonicum). The high counts of filamentous fungi in raw materials and air samples in processing steps such as cooling, slicing, and packaging, suggest that contamination that may occur in these steps can be critical for the shelf life of breads. The results of this study highlight that the prevention of contamination of breads by fungal spores is still a challenge for bakery industries and that other strategies such as control of germination and growth of spoilage fungi through the development of more stable formulations have to be developed. Copyright © 2016 Elsevier Ltd. All rights reserved.

Identifying Major Transitions in the Evolution of Lithic Cutting Edge Production Rates.

PubMed

Muller, Antoine; Clarkson, Chris

2016-01-01

The notion that the evolution of core reduction strategies involved increasing efficiency in cutting edge production is prevalent in narratives of hominin technological evolution. Yet a number of studies comparing two different knapping technologies have found no significant differences in edge production. Using digital analysis methods we present an investigation of raw material efficiency in eight core technologies broadly representative of the long-term evolution of lithic technology. These are bipolar, multiplatform, discoidal, biface, Levallois, prismatic blade, punch blade and pressure blade production. Raw material efficiency is assessed by the ratio of cutting edge length to original core mass. We also examine which flake attributes contribute to maximising raw material efficiency, as well as compare the difference between expert and intermediate knappers in terms of cutting edge produced per gram of core. We identify a gradual increase in raw material efficiency over the broad sweep of lithic technological evolution. The results indicate that the most significant transition in efficiency likely took place with the introduction of small foliate biface, Levallois and prismatic blade knapping, all introduced in the Middle Stone Age / Middle Palaeolithic among early Homo sapiens and Neanderthals. This suggests that no difference in raw material efficiency existed between these species. With prismatic blade technology securely dated to the Middle Palaeolithic, by including the more recent punch and pressure blade technology our results dispel the notion that the transition to the Upper Palaeolithic was accompanied by an increase in efficiency. However, further increases in cutting edge efficiency are evident, with pressure blades possessing the highest efficiency in this study, indicating that late/epi-Palaeolithic and Neolithic blade technologies further increased efficiency.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boussaa, S. Anas, E-mail: sabiha.anas@gmail.com; Kheloufi, A.; Kefaifi, A.

Raw materials are essential for the functioning of modern societies, and access to these raw materials is vital to the world economy. Sustainable development, both globally level, raises important new challenges associated with access and efficient use of raw materials. High purity quartz, is consider as a critical raw material and it is a rare commodity that only forms under geological conditions where a narrow set of chemical and physical parameters is fulfilled. When identified and following special beneficiation techniques, high purity quartz obtains very attractive prices and is applied in high technology sectors that currently are under rapid expansionmore » such as photovoltaic solar cells, silicon metal - oxide wafers in the semiconductor industry and long distance optical fibers that are used in communication networks. Crystalline silicon remains the principal material for photovoltaic technology. Metallurgical silicon is produced industrially by the reduction of silica with carbon in an electric arc furnace at temperatures higher than 2000 °C in the hottest parts, by a reaction that can be written ideally as: SiO{sub 2} + 2C = Si + 2CO. The aim of this study has been to test experimental methods for investigating the various physical and chemical proprieties of Hoggar quartz with different techniques: X Ray Fluorescence, infra-red spectroscopy, Scanning Electron Microscopy, Optic Microscopy, Carbon Analyzer and Vickers Hardness. The results show finally that the quartz has got good result in purity but need enrichment for the photovoltaic application.« less

The effects of fabric type, fabric width and model type on the cost of unit raw material in terms of apparel

NASA Astrophysics Data System (ADS)

Bilgiç, H.; Duru Baykal, P.

2017-10-01

The cost of the fabric which is the raw material of apparel constitutes approximately the half of the total product cost. So, it is highly important that the fabric should be used with the greatest productivity. Cost analysis are of great importance in terms of competitiveness of readymade clothing and apparel sector both in national and international markets. The proximity of costs to international average and the average cost of the countries that are competitors of Turkey in clothing market is essential for Turkey to sustain its effect in textile sector. In the contrary case, the sector won’t be able to maintain its competitive capacity sustainably [1].The main cost elements of textile and apparel sector consist of raw material, labor, energy and financing [2].

Determination of Chondroitin Sulfate Content in Raw Materials and Dietary Supplements by High-Performance Liquid Chromatography with UV Detection After Enzymatic Hydrolysis: Single-Laboratory Validation First Action 2015.11.

PubMed

Brunelle, Sharon L

2016-01-01

A previously validated method for determination of chondroitin sulfate in raw materials and dietary supplements was submitted to the AOAC Expert Review Panel (ERP) for Stakeholder Panel on Dietary Supplements Set 1 Ingredients (Anthocyanins, Chondroitin, and PDE5 Inhibitors) for consideration of First Action Official Methods(SM) status. The ERP evaluated the single-laboratory validation results against AOAC Standard Method Performance Requirements 2014.009. With recoveries of 100.8-101.6% in raw materials and 105.4-105.8% in finished products and precision of 0.25-1.8% RSDr within-day and 1.6-4.72% RSDr overall, the ERP adopted the method for First Action Official Methods status and provided recommendations for achieving Final Action status.

Measurement of the isotope ratio of acetic acid in vinegar by HS-SPME-GC-TC/C-IRMS.

PubMed

Hattori, Ryota; Yamada, Keita; Shibata, Hiroki; Hirano, Satoshi; Tajima, Osamu; Yoshida, Naohiro

2010-06-23

Acetic acid is the main ingredient of vinegar, and the worth of vinegar often depends on the fermentation of raw materials. In this study, we have developed a simple and rapid method for discriminating the fermentation of the raw materials of vinegar by measuring the hydrogen and carbon isotope ratio of acetic acid using head space solid-phase microextraction (HS-SPME) combined with gas chromatography-high temperature conversion or combustion-isotope ratio mass spectrometry (GC-TC/C-IRMS). The measurement of acetic acid in vinegar by this method was possible with repeatabilities (1sigma) of +/-5.0 per thousand for hydrogen and +/-0.4 per thousand for carbon, which are sufficient to discriminate the origin of acetic acid. The fermentation of raw materials of several vinegars was evaluated by this method.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Covey, S.K.

As this century comes to a close, landfills are being opened, closed and mined for resources; commercial businesses and manufacturers are under pressure to be responsible both environmentally and economically. The timing is right for individuals and organizations to start listening to each other and working cooperatively for a greater good. In 1996, an ad hoc group of state government agencies, private business, not-for-profits and educational institutions met to discuss the potential for a materials exchange in Ohio. The Ohio Materials Exchange (OMEX) exists today from the cooperation and funding form the Ohio Environmental Education Fund (OEEF), The Association ofmore » Ohio Recyclers (AOR) in cooperation with Waste Alternatives, Inc., The Ohio Environmental Protection Agency (OhEPA) (Division of Solid and Infectious Waste Management and the Office of Pollution Prevention), The Ohio Department of Natural Resources (Division of Recycling and Litter Prevention) and the Ohio Department of Development (ODOD) (Office of Energy Efficiency OEE). In addition, private business, solid waste management districts and individual organizations who use the exchange actively help guide and market the program. The author was employed with the ODOD-OEE and a member of the planning team. A materials exchange allows companies to trade, sell or give away unwanted materials to one another and use it as raw material for manufacturing or reuse in its existing form (Table 1.). Materials exchanges were both out of necessity in World War II but are continuing due to foresight. (EPA 1994) The exchange of raw product, rejects or waste can reduce waste and save energy. Not only do recycled materials often use less energy to produce the product, the trading may save hauling or disposal costs, that could then be diverted to purchase new, more efficient equipment. The materials available or wanted are collected into lists. These lists may take the form of catalogs, fax-back systems, Internet or computer or index cards with a rolodex and a phone. A form is filled out requesting contact information. From that point, the arrangements are made between the trading partners. Often the exchange host will attempt to find out if a successful trade has been made. All liability issues are usually assumed by the trading partners and not the exchange service. This paper includes references for further reading concerning the history and impact of local, regional and national exchanges.« less

Dataset on the structural characterization of organosolv lignin obtained from ensiled Poaceae grass and load-dependent molecular weight changes during thermoplastic processing.

PubMed

Dörrstein, Jörg; Scholz, Ronja; Schwarz, Dominik; Schieder, Doris; Sieber, Volker; Walther, Frank; Zollfrank, Cordt

2018-04-01

This article presents experimental data of organosolv lignin from Poacea grass and structural changes after compounding and injection molding as presented in the research article "Effects of high-lignin-loading on thermal, mechanical, and morphological properties of bioplastic composites" [1]. It supplements the article with morphological (SEM), spectroscopic ( 31 P NMR, FT-IR) and chromatographic (GPC, EA) data of the starting lignin as well as molar mass characteristics (mass average molar mass (M w ) and Polydispersity (D)) of the extracted lignin. Refer to Schwarz et al. [2] for a detailed description of the production of the organosolv residue and for further information on the raw material used for lignin extraction. The dataset is made publicly available and can be useful for extended lignin research and critical analyzes.

Science and technology roadmap for graphene, related two-dimensional crystals, and hybrid systems

NASA Astrophysics Data System (ADS)

Ferrari, Andrea C.; Bonaccorso, Francesco; Fal'Ko, Vladimir; Novoselov, Konstantin S.; Roche, Stephan; Bøggild, Peter; Borini, Stefano; Koppens, Frank H. L.; Palermo, Vincenzo; Pugno, Nicola; Garrido, José A.; Sordan, Roman; Bianco, Alberto; Ballerini, Laura; Prato, Maurizio; Lidorikis, Elefterios; Kivioja, Jani; Marinelli, Claudio; Ryhänen, Tapani; Morpurgo, Alberto; Coleman, Jonathan N.; Nicolosi, Valeria; Colombo, Luigi; Fert, Albert; Garcia-Hernandez, Mar; Bachtold, Adrian; Schneider, Grégory F.; Guinea, Francisco; Dekker, Cees; Barbone, Matteo; Sun, Zhipei; Galiotis, Costas; Grigorenko, Alexander N.; Konstantatos, Gerasimos; Kis, Andras; Katsnelson, Mikhail; Vandersypen, Lieven; Loiseau, Annick; Morandi, Vittorio; Neumaier, Daniel; Treossi, Emanuele; Pellegrini, Vittorio; Polini, Marco; Tredicucci, Alessandro; Williams, Gareth M.; Hee Hong, Byung; Ahn, Jong-Hyun; Min Kim, Jong; Zirath, Herbert; van Wees, Bart J.; van der Zant, Herre; Occhipinti, Luigi; Di Matteo, Andrea; Kinloch, Ian A.; Seyller, Thomas; Quesnel, Etienne; Feng, Xinliang; Teo, Ken; Rupesinghe, Nalin; Hakonen, Pertti; Neil, Simon R. T.; Tannock, Quentin; Löfwander, Tomas; Kinaret, Jari

2015-03-01

We present the science and technology roadmap for graphene, related two-dimensional crystals, and hybrid systems, targeting an evolution in technology, that might lead to impacts and benefits reaching into most areas of society. This roadmap was developed within the framework of the European Graphene Flagship and outlines the main targets and research areas as best understood at the start of this ambitious project. We provide an overview of the key aspects of graphene and related materials (GRMs), ranging from fundamental research challenges to a variety of applications in a large number of sectors, highlighting the steps necessary to take GRMs from a state of raw potential to a point where they might revolutionize multiple industries. We also define an extensive list of acronyms in an effort to standardize the nomenclature in this emerging field.

Hemp as an Agricultural Commodity

DTIC Science & Technology

2014-02-14

yarns and raw or processed spun fibers, paper, carpeting, home furnishings, construction and insulation materials, auto parts, and composites. The...interior stalk (hurd) is used in various applications such as animal bedding, raw material inputs, low-quality papers, and composites. Hemp seed and...oilcake are used in a range of foods and beverages, and can be an alternative food protein source. Oil from the crushed hemp seed is an ingredient in a

VIEW IN OPPOSITE DIRECTION AS MD1351 AND MD1352. RAW MATERIAL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

VIEW IN OPPOSITE DIRECTION AS MD-135-1 AND MD-135-2. RAW MATERIAL CONVEYOR AT LEFT DEPOSITS SHELL INTO MILLING MACHINE AT LOWER LEFT. ENGINE IS AT LOWER RIGHT AND RADIATOR AT LOWER CENTER. ROLLER SORTER IS AT TOP OF CONVEYOR. - F. & H. Benning Company Oyster Mill, 14430 Solomons Island Road (moved from 1014 Benning Road, Galesville, Anne Arundel County, Maryland), Solomons, Calvert County, MD

Behavior or Nonmetallic Materials in Shale Oil Derived Jet Fuels and in High Aromatic and High Sulfur Petroleum Fuels

DTIC Science & Technology

1978-07-01

degrades thermal stability and forms undesirable sulfur dioxide emissions . Although the original premises for controlling total sulfur may not still...eliminate corrosive trace contamination, presence of surfactants which deactivate filter/ separators, carry-over of refinery processing materials, and...increase raw vapor emissions from ground fuel handling facilities and during refueling operations. Controlling raw vapor emissions is difficult at 3

Coal gasification systems engineering and analysis. Appendix A: Coal gasification catalog

NASA Technical Reports Server (NTRS)

1980-01-01

The scope of work in preparing the Coal Gasification Data Catalog included the following subtasks: (1) candidate system subsystem definition, (2) raw materials analysis, (3) market analysis for by-products, (4) alternate products analysis, (5) preliminary integrated facility requirements. Definition of candidate systems/subsystems includes the identity of and alternates for each process unit, raw material requirements, and the cost and design drivers for each process design.

Determination of platinum in mineral raw materials by switching chronoamperometry

NASA Astrophysics Data System (ADS)

Pakrieva, E.; Oskina, Y.; Ustinova, E.

2014-08-01

The technique of platinum (IV) determination in mineral raw materials with the application of switching chronoamperometry has been offered. The graphite electrode impregnated with polyethylene was used as the working electrode. The hydrolytic precipitation method with 3% NaOH solution has been developed to separate platinum from the sample matrix. The use of switching chronoamperometry applied to the assessment of the platinum content in geological objects has been demonstrated.

Quantitative Analysis of Aloins and Aloin-Emodin in Aloe Vera Raw Materials and Finished Products Using High-Performance Liquid Chromatography: Single-Laboratory Validation, First Action 2016.09.

PubMed

Kline, David; Ritruthai, Vicha; Babajanian, Silva; Gao, Quanyin; Ingle, Prashant; Chang, Peter; Swanson, Gary

2017-05-01

A single-laboratory validation study is described for a method of quantitative analysis of aloins (aloins A and B) and aloe-emodin in aloe vera raw materials and finished products. This method used HPLC coupled with UV detection at 380 nm for the aloins and 430 nm for aloe-emodin. The advantage of this test method is that the target analytes are concentrated from the sample matrix (either liquid or solid form) using stepwise liquid-liquid extraction (water-ethyl acetate-methanol), followed by solvent evaporation and reconstitution. This sample preparation process is suitable for different forms of products. The concentrating step for aloins and aloe-emodin has enhanced the method quantitation level to 20 parts per billion (ppb). Reversed-phase chromatography using a 250 × 4.6 mm column under gradient elution conditions was used. Mobile phase A is 0.1% acetic acid in water and mobile phase B is 0.1% acetic acid in acetonitrile. The HPLC run starts with a 20% mobile phase B that reaches 35% at 13 min. From 13 to 30 min, mobile phase B is increased from 35 to 100%. From 30 to 40 min, mobile phase B is changed from 100% back to the initial condition of 20% for re-equilibration. The flow rate is 1 mL/min, with a 100 μL injection volume. Baseline separation (Rs > 2.0) for aloins A and B and aloe-emodin was observed under this chromatographic condition. This test method was validated with raw materials of aloe vera 5× (liquid) and aloe vera 200× (powder) and finished products of aloe concentrate (liquid) and aloe (powder). The linearity of the method was studied from 10 to 500 ppb for aloins A and B and aloe-emodin, with correlation coefficients of 0.999964, 0.999957, and 0.999980, respectively. The test method was proven to be specific, precise, accurate, rugged, and suitable for the intended quantitative analysis of aloins and aloe-emodin in raw materials and finished products. The S/N for aloins A and B and aloe-emodin at 10 ppb level were 12, 10, and 8, respectively, indicating our conservative LOD level at 10 ppb (the typical LOD level S/N is about 3). The S/N for aloins A and B and aloe-emodin at the 20 ppb level were 17, 14, and 16, respectively, indicating our conservative LOQ level at 20 ppb (the typical LOQ level S/N is about 10). The stock standard solution of a mixture of aloins and aloe-emodin and a working standard solution were found to be stable for at least 19 days when stored refrigerated at 2-8°C, with a recovery of 100 ± 5%.

The Enhanced Red Emission and Improved Thermal Stability of CaAlSiN3:Eu2+ Phosphors by Using Nano-EuB6 as Raw Material

PubMed Central

Liu, Wen-Quan; Wu, Dan; Chang, Hugejile; Duan, Ru-Xia; Wu, Wen-Jie; Amu, Guleng; Bao, Fu-Quan; Tegus, Ojiyed

2018-01-01

Synthesizing phosphors with high performance is still a necessary work for phosphor-converted white light-emitting diodes (W-LEDs). In this paper, three series of CaAlSiN3:Eu2+ (denoted as CASN:Eu2+) phosphors using Eu2O3, EuN and EuB6 as raw materials respectively are fabricated by under the alloy precursor normal pressure nitridation synthesis condition. We demonstrate that CASN:Eu2+ using nano-EuB6 as raw material shows higher emission intensity than others, which is ascribed to the increment of Eu2+ ionic content entering into the crystal lattice. An improved thermal stability can also be obtained by using nano-EuB6 due to the structurally stable status, which is assigned to the partial substitution of Eu–O (Eu–N) bonds by more covalent Eu–B ones that leads to a higher structural rigidity. In addition, the W-LEDs lamp was fabricated to explore its possible application in W-LEDs based on blue LEDs. Our results indicate that using EuB6 as raw materials can provide an effective way of enhancing the red emission and improving the thermal stability of the CASN:Eu2+ red phosphor. PMID:29370148

Provenance study of ancient Chinese Yaozhou porcelain by neutron activation analysis

NASA Astrophysics Data System (ADS)

Li, G. X.; Y Gao, Z.; Li, R. W.; Zhao, W. J.; Xie, J. Z.; Feng, S. L.; Zhuo, Z. X.; Y Fan, D.; Zhang, Y.; Cai, Z. F.; Liu, H.

2003-09-01

This paper reports our study of the provenance of ancient Chinese Yaozhou porcelain. The content of 29 elements in the Yaozhou porcelain samples was measured by neutron activation analysis (NAA). The NAA data were further analysed using fuzzy cluster analysis to obtain the trend fuzzy cluster diagrams. These samples with different glaze colour, ranging over more than 700 years, were fired in different kilns. Our analysis indicates the relatively concentrated distribution of the sources of the raw material for the Yaozhou porcelain body samples. They can be classified into two independent periods, i.e. the Tang (AD 618-907) and the Five Dynasties (AD 907-960) period, and the Song (AD 960-1279) and Jin (AD 1115-1234) period. Our analysis also indicates that the sources of the raw material for the ancient Yaozhou porcelain glaze samples are quite scattered and those for the black glaze in the Tang Dynasty are very concentrated. The sources of the raw material for the celadon glaze and the white glaze in the Tang Dynasty are widely distributed and those for the celadon glaze in the Song Dynasty are close to those of the bluish white glaze in the Jin Dynasty, and they are very concentrated. The sources of the raw material for the porcelain glazes cover those of the porcelain bodies.

Greenhouse Gas Emissions from Asphalt Pavement Construction: A Case Study in China

PubMed Central

Ma, Feng; Sha, Aimin; Lin, Ruiyu; Huang, Yue; Wang, Chao

2016-01-01

In China, the construction of asphalt pavement has a significant impact on the environment, and energy use and greenhouse gas (GHG) emissions from asphalt pavement construction have been receiving increasing attention in recent years. At present, there is no universal criterion for the evaluation of GHG emissions in asphalt pavement construction. This paper proposes to define the system boundaries for GHG emissions from asphalt pavement by using a process-based life cycle assessment method. A method for evaluating GHG emissions from asphalt pavement construction is suggested. The paper reports a case study of GHG emissions from a typical asphalt pavement construction project in China. The results show that the greenhouse gas emissions from the mixture mixing phase are the highest, and account for about 54% of the total amount. The second highest GHG emission phase is the production of raw materials. For GHG emissions of cement stabilized base/subbase, the production of raw materials emits the most, about 98%. The GHG emission for cement production alone is about 92%. The results indicate that any measures to reduce GHG emissions from asphalt pavement construction should be focused on the raw materials manufacturing stage. If the raw materials production phase is excluded, the measures to reduce GHG emissions should be aimed at the mixture mixing phase. PMID:27011196

Greenhouse Gas Emissions from Asphalt Pavement Construction: A Case Study in China.

PubMed

Ma, Feng; Sha, Aimin; Lin, Ruiyu; Huang, Yue; Wang, Chao

2016-03-22

In China, the construction of asphalt pavement has a significant impact on the environment, and energy use and greenhouse gas (GHG) emissions from asphalt pavement construction have been receiving increasing attention in recent years. At present, there is no universal criterion for the evaluation of GHG emissions in asphalt pavement construction. This paper proposes to define the system boundaries for GHG emissions from asphalt pavement by using a process-based life cycle assessment method. A method for evaluating GHG emissions from asphalt pavement construction is suggested. The paper reports a case study of GHG emissions from a typical asphalt pavement construction project in China. The results show that the greenhouse gas emissions from the mixture mixing phase are the highest, and account for about 54% of the total amount. The second highest GHG emission phase is the production of raw materials. For GHG emissions of cement stabilized base/subbase, the production of raw materials emits the most, about 98%. The GHG emission for cement production alone is about 92%. The results indicate that any measures to reduce GHG emissions from asphalt pavement construction should be focused on the raw materials manufacturing stage. If the raw materials production phase is excluded, the measures to reduce GHG emissions should be aimed at the mixture mixing phase.

76 FR 35239 - Importer of Controlled Substances; Notice of Application

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-16

... (9040) II Raw Opium (9600) II Poppy Straw (9650) II Concentrate of Poppy Straw (9670) II The company... narcotic raw material are not appropriate. As noted in a previous notice published in the Federal Register...

76 FR 25374 - Importer of Controlled Substances; Notice of Application

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-04

...), comments and requests for hearings on applications to import narcotic raw material are not appropriate. As... Schedule Raw Opium (9600) I Concentrate of Poppy Straw (9670) II The company plans to import the listed...

77 FR 19717 - Importer of Controlled Substances; Notice of Registration Mallinckrodt LLC

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-02

... raw material are not appropriate, 72 FR 3417 (2007). Regarding all other basic classes of controlled...) II Opium, raw (9600) II Poppy Straw Concentrate (9670) II The company plans to import the listed...

75 FR 36680 - Importer of Controlled Substances; Notice of Application

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-28

... requests for hearings on applications to import narcotic raw material are not appropriate. As noted in a... as an importer of the basic classes of controlled substances listed in schedule II: Drug Schedule Raw...

75 FR 22844 - Importer of Controlled Substances; Notice of Application

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-30

... narcotic raw material are not appropriate. As noted in a previous notice published in the Federal Register... Coca Leaves (9040) II Raw Opium (9600) II Poppy Straw (9650) II Concentrate of Poppy Straw (9670) II...

77 FR 24984 - Importer of Controlled Substances; Notice of Application; Rhodes Technologies

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-26

.... Comments and requests for hearings on applications to import narcotic raw material are not appropriate. 72... schedule II: Drug Schedule Opium, Raw (9600) II Poppy Straw Concentrate (9670) II The company plans to...

75 FR 53718 - Importer of Controlled Substances; Notice of Application

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-01

... 3417 (2007), comments and requests for hearings on applications to import narcotic raw material are not... Opium, raw (9600) II Poppy Straw Concentrate (9670) II The company plans to import the basic classes of...

78 FR 12101 - Importer of Controlled Substances; Notice of Application; Mallinckrodt, LLC.

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-21

... Coca Leaves (9040) II Opium, raw (9600) II Poppy Straw Concentrate (9670) II The company plans to... or coca leaves. Comments and requests for hearings on applications to import narcotic raw material...

Materials and manufacturing processes for increased life/reliability. [of turbine wheels

NASA Technical Reports Server (NTRS)

Duttweiler, R. E.

1977-01-01

Improvements in both quality and durability of disk raw material for both military and commercial engines necessitated an entirely new concept in raw material process control which imposes careful selection, screening and sampling of the basic alloy ingredients, followed by careful monitoring of the melting parameters in all phases of the vacuum melting sequence. Special care is taken to preclude solidification conditions that produce adverse levels of segregation. Melt furnaces are routinely cleaned and inspected for contamination. Ingots are also cleaned and inspected before entering the final melt step.

Exopolysaccharide production from Sclerotium glucanicum NRRL 3006 and Botryosphaeria rhodina DABAC-P82 on raw and hydrolysed starchy materials.

PubMed

Selbmann, L; Crognale, S; Petruccioli, M

2002-01-01

Evaluation of fermentative usage of raw starchy materials for exopolysaccharide (EPS) production by Sclerotium glucanicum NRRL 3006 and Botryosphaeria rhodina DABAC-P82. Non-hydrolysed corn starch, soft wheat flour, potato flour, cassava flour, sweet and industrial potato flours, and corn starch hydrolysed to different dextrose equivalent (DE) were tested in shaken culture for EPS production. Both fungal strains produced EPS on all tested materials but the production was maximum on hydrolysed corn starch (30.5 and 19.8 g l(-1) by B. rhodina and S. glucanicum on corn starch at 100 and 62 DE, respectively). Raw starchy materials as such and, in particular, partially or totally hydrolysed corn starch could be used profitably for EPS production by S. glucanicum and B. rhodina. The excellent EPS production, productivity and yield of B. rhodina DABAC-P82 when grown on 60 g l(-1) of totally hydrolysed corn starch.

A small scale lunar launcher for early lunar material utilization

NASA Technical Reports Server (NTRS)

Snow, W. R.; Kubby, J. A.; Dunbar, R. S.

1981-01-01

A system for the launching of lunar derived oxygen or raw materials into low lunar orbit or to L2 for transfer to low earth orbit is presented. The system described is a greatly simplified version of the conventional and sophisticated approach suggested by O'Neill using mass drivers with recirculating buckets. An electromagnetic accelerator is located on the lunar surface which launches 125 kg 'smart' containers of liquid oxygen or raw materials into a transfer orbit. Upon reaching apolune a kick motor is fired to circularize the orbit at 100 km altitude or L2. These containers are collected and their payloads transferred to a tanker OTV. The empty containers then have their kick motors refurbished and then are returned to the launcher site on the lunar surface for reuse. Initial launch capability is designed for about 500T of liquid oxygen delivered to low earth orbit per year with upgrading to higher levels, delivery of lunar soil for shielding, or raw materials for processing given the demand.

Lime kiln dust as a potential raw material in portland cement manufacturing

USGS Publications Warehouse

Miller, M. Michael; Callaghan, Robert M.

2004-01-01

In the United States, the manufacture of portland cement involves burning in a rotary kiln a finely ground proportional mix of raw materials. The raw material mix provides the required chemical combination of calcium, silicon, aluminum, iron, and small amounts of other ingredients. The majority of calcium is supplied in the form of calcium carbonate usually from limestone. Other sources including waste materials or byproducts from other industries can be used to supply calcium (or lime, CaO), provided they have sufficiently high CaO content, have low magnesia content (less than 5 percent), and are competitive with limestone in terms of cost and adequacy of supply. In the United States, the lime industry produces large amounts of lime kiln dust (LKD), which is collected by dust control systems. This LKD may be a supplemental source of calcium for cement plants, if the lime and cement plants are located near enough to each other to make the arrangement economical.

Deformation of metal brackets: a comparative study.

PubMed

Flores, D A; Choi, L K; Caruso, J M; Tomlinson, J L; Scott, G E; Jeiroudi, M T

1994-01-01

The purpose of this study was to determine the effect of material and design on the force and stress required to permanently deform metal brackets. Fourteen types of metal brackets were categorized according to raw material composition, slot torque degree, and wing type. Five types of raw materials, three types of slot torque degree, and four types of wing design were tested using an archwire torque test developed by Flores. An analysis of variance (ANOVA) and t-test showed that all three categories had a significant effect on the force and stress needed to permanently deform metal brackets. Of the three, raw material had the greatest effect on the amount of force. Results showed that 17-4PH and 303S had higher yield strengths and regular twin brackets had higher resistance to deformation. Also, as slot torque degree increased, brackets deformed with less force. Result confirmed that brackets requiring the greatest stress to permanently deform were made of steel with the greatest hardness.

Prospects of rice straw as a raw material for paper making.

PubMed

Kaur, Daljeet; Bhardwaj, Nishi Kant; Lohchab, Rajesh Kumar

2017-02-01

Pulp and paper mills are indispensable for any nation as far as the growth of the nation is concerned. Due to fast growth in population, urbanization and industrialization, the demand and consumption of paper has increased tremendously. These put high load on our natural resources and force the industry to look for alternative raw material. Rice straw is a lignocellulosic material abundantly available in wood short countries like China, India, Bangladesh, etc. and can be used as raw material for this industry. Open burning of rice straw releases noxious green house gases to the air and poses serious threats to global air chemistry and human health. So, it is a dual benefit option (for farmers and industries) to use rice straw as a raw material in pulp and paper industry. Organosolv pulping using acids are the prominent choices of researchers to convert this residue into valuable pulp but in developed countries only. Developing world favours the soda and soda-AQ processes as these are economical. As a virtue of less lignin content in comparison to wood, rice straw requires less harsh conditions for cooking and can be easily pulped. Bleaching is a crucial step of paper making but also responsible for causing water pollution. Many studies revealed that during the process more than 500 chlorinated compounds are released that are highly toxic, bioaccumulative and carcinogenic in nature. Most of the industries over the globe switch on to the elemental chlorine free short sequence bleaching methods using chlorine dioxide, hypochlorite and hydrogen peroxide. This paper presented the effective need of ecofriendly, economically reliable pulping and bleaching sequences in case of rice straw to eliminate the problems of chlorinated compounds in wastewater of paper mills. Such approach of using waste as a raw material with its environmentally safe processing for making paper can prove to be valuable towards sustainable growth. Copyright © 2016 Elsevier Ltd. All rights reserved.

ERA-MIN: The European network (ERA-NET) on non-energy raw materials

NASA Astrophysics Data System (ADS)

vidal, o.; christmann, p.; Bol, d.; Goffé, b.; Groth, m.; Kohler, e.; Persson Nelson, k.; Schumacher, k.

2012-04-01

Non-energy raw materials are vital for the EU's economy, and for the development of environmentally friendly technologies. The EU is the world's largest consumers of non-energy minerals, but it remains dependent on the importation of many metals, as its domestic production is limited to about 3% of world production. We will present the project ERA-MIN, which is an ERA-NET on the Industrial Handling of Raw Materials for European industries, financially supported by the European Commission. The main objectives of ERA-MIN are: 1) Mapping and Networking: interconnecting the members of the currently fragmented European mineral resources research area, to the aim of fostering convergence of public research programs, industry, research institutes, academia and the European Commission, 2) Coordinating: establishing a permanent mechanism for planning and coordination of the European non-energy mineral raw materials research community (ENERC). 3) Roadmapping: defining the most important scientific and technological challenges that should be supported by the EU and its state members, 4) Programming: designing a Joint European Research Programme model and implementating it into a call for proposals open to academic and industrial research. The topics of interest in ERA-MIN are the primary continental and marine resources, the secondary resources and their related technologies, substitution and material efficiency, along with transversal topics such as environmental impact, public policy support, mineral intelligence, and public education and teaching. Public scientific research is very central in the scope of the ERA-MIN activity, whose consortium is indeed lead by a public organisation of fundamental research. Thus, universities and public research organisations are warmly invited to play an active role in defining the scientific questions and challenges that shall determine the European Raw Materials Roadmap and should be addressed by joint programming at the European scale. The various levels of possible involvement in ERA-MIN for the interested stakeholders will be presented.

VERAM, for a sustainable and competitive future for EU Raw Materials

NASA Astrophysics Data System (ADS)

Mobili, A.; Tittarelli, F.; Revel, G. M.; Wall, P.

2018-03-01

The project, VERAM “Vision and Roadmap for European Raw Materials”, aims to deliver a mapping of on-going initiatives on non-food, non-energy raw materials (including metals, industrial minerals, aggregates and wood) at European, Member State, and regional levels both from the Research and Innovation (R&I), industry, and policy perspectives. Moreover, based on a comprehensive gap analysis, VERAM will propose a common long term 2050 Vision and Roadmap in coordination and cooperation with all stakeholders across the value chain. For the first time, two European Technology Platforms (ETPs) together with their corresponding European Research Area Networks (ERA-NETs) are joining forces to develop a common roadmap.

FROZEN RAW FOODS AS SKIN-TESTING MATERIALS—Further Studies of Use in Cases of Allergic Disorders

PubMed Central

Ancona, Giacomo R.; Schumacher, Irwin C.

1954-01-01

In further studies on the use of frozen raw food as skin-testing material in patients with allergic disorders, the results of previous work were confirmed in a greater number of subjects using a larger number of foods: Tests with frozen raw foods by the scratch method induce true positive reactions of a larger size and in greater frequency than the corresponding commercial extracts by either the scratch or the intracutaneous method. Storage in the frozen state for several years does not affect the antigenic potency of the materials. The frozen preparations have caused no harmful effects in the subjects, are free from irritant properties, and are not urticariogenic. PMID:13126823

Map of critical raw material deposits in Europe

NASA Astrophysics Data System (ADS)

Guillaume, Bertrand

2016-04-01

Map of critical raw material deposits in Europe Guillaume BERTRAND1, Daniel CASSARD1, Nikolaos ARVANITIDIS2, Gerry STANLEY3 and the EuroGeoSurvey Mineral Resources Expert Group4. 1 - Bureau de Recherches Géologiques et Minières (BRGM), Georesources Divison, 3 avenue Claude Guillemin, 45060 Orléans cedex 2, FRANCE. 2 - Sveriges Geologiska Undersökning (SGU), Box 670, SE-751 28, Uppsala, SWEDEN 3 - Geological Survey of Ireland (GSI), Beggars Bush, Haddington Road, Dublin D04 K7X4, IRELAND 4 - EuroGeoSurveys, Rue Joseph II 36-38, 1000 Brussels, BELGIUM The Critical Raw Material (CRM) Deposit Map of Europe, prepared by EuroGeoSurvey's Mineral Resources Expert Group (MREG), shows European mineral deposits from the ProMine Mineral Deposit database containing critical commodities, according to the 2014 list of critical raw materials of the European Commission. EuroGeoSurveys (EGS), The Geological Surveys of Europe, is a not-for-profit organization representing 37 National Geological Surveys and some regional Geological Surveys in Europe. It provides the European Institutions with expert, independent, balanced and practical pan-European advice and information as an aid to problem-solving, policy development, regulatory and programme formulation in areas such as natural resources, energy and geo-hazards. The EGS MREG is actively involved in contributing to policy and strategy-making processes aimed at identifying, characterizing and safeguarding resource potential, especially for critical raw materials through data provision, research, technological development and innovation. The European Union aspires to reducing the import dependency of raw materials, especially CRM, that are essential to Europe's industries. In this respect, mineral resource information, data sharing and networking by European Geological Surveys is crucial. The Strategic Implementation Plan of the European Innovation Partnership on Raw Materials highlights the need for establishing and maintaining a common interoperable EU Geological Knowledge Base. Such a Knowledge Base will support exploration for indigenous mineral resources and strengthen policy and decision making. In 2010, the European Commission identified 14 non energy non-agricultural raw materials as being critical. Criticality is based on both the scarcity of supply and the importance to European industry. This list was updated in 2014 to include 7 new commodities with one being dropped from the original list. The list now comprises: antimony, beryllium, borates, chromium, cobalt, coking coal, fluorspar, gallium, germanium, graphite, indium, magnesite, magnesium, niobium, phosphate rock, platinum group metals, light and heavy rare earth elements (separately), silicon metal and tungsten. ProMine was a European Union (EU) co-funded project, which had as its main objective the stimulation of the extractive industry to deliver new products to manufacturing industry. A major deliverable of the project was the ProMine Mineral Deposit (MD) database that contains information related to almost 13,000 mineral deposits in Europe. In order to extract data to be displayed on the CRM map of Europe, the ProMine MD database was queried for all commodities on the EC CRM list which were in the medium to super-large deposit size. Following this, the dataset was circulated to MREG in order to verify, validate and update the list.

78 FR 19016 - Importer of Controlled Substances; Notice of Registration; Johnson Matthey, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-28

... Schedule Coca Leaves (9040) II Thebaine (9333) II Opium, raw (9600) II Noroxymorphone (9668) II Poppy Straw Concentrate (9670) II The company plans to import the listed controlled substances as raw materials, to be...

76 FR 51400 - Importer of Controlled Substances; Notice of Registration

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-18

... narcotic raw material are not appropriate. DEA has considered the factors in 21 U.S.C. 823(a) and 952(a... classes of controlled substances: Drug Schedule Raw Opium (9600) II Concentrate of Poppy Straw II (9670...

77 FR 55503 - Importer of Controlled Substances; Notice of Registration; Cambrex Charles City, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-10

... hearings on applications to import narcotic raw material are not appropriate. 72 FR 3417 (2007). DEA has...-piperidine (8333).. II Phenylacetone (8501) II Opium, raw (9600) II Poppy Straw Concentrate (9670) II The...

78 FR 39337 - Importer of Controlled Substances; Notice Of Registration; Mallinckrodt, LLC.

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-01

... narcotic raw material are not appropriate, 72 FR 3417 (2007). Regarding Phenylacetone (8501), a basic class... Phenylacetone (8501) II Coca Leaves (9040) II Opium, raw (9600) II Poppy Straw Concentrate (9670) II The company...

78 FR 23594 - Importer of Controlled Substances; Notice of Application; Rhodes Technologies

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-19

... requests for hearings on applications to import narcotic raw material are not appropriate. 72 FR 3417 (2007... Schedule Opium, Raw (9600) II Poppy Straw Concentrate (9670) II The company plans to import the listed...

77 FR 24983 - Importer of Controlled Substances; Notice of Application Penick Corporation

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-26

... import narcotic raw material are not appropriate. 72 FR 3417(2007). As noted in a previous notice... Schedule Coca Leaves (9040) II Raw Opium (9600) II Poppy Straw (9650) II Concentrate of Poppy Straw (9670...

Rational preparation of waste coal mixture for production of bricks by the method of compression molding

NASA Astrophysics Data System (ADS)

Stolboushkin, A. Yu; Ivanov, A. I.; Temlyantsev, M. V.; Fomina, O. A.

2016-10-01

Rational preparation of the mixture containing technogenic raw material - waste coal for the production of wall ceramics is developed. It was established that the technology of high-quality ceramic bricks requires: grinding of raw materials to class 0.3 + 0 mm, its aggregation in the intensive mixers into granules 1-3 mm, compression molding of adobe to plastic deformation of granules, drying and firing.

Computer Vision Hardware System for Automating Rough Mills of Furniture Plants

Treesearch

Richard W. Conners; Chong T. Ng; Thomas H. Drayer; Joe G. Tront; D. Earl Kline; C.J. Gatchell

1990-01-01

The rough mill of a hardwood furniture or fixture plant is the place where dried lumber is cut into the rough parts that will be used in the rest of the manufacturing process. Approximately a third of the cost of operating the rough mill is the cost of the raw material. Hence any increase in the number of rough parts produced from a given volume of raw material can...

Increasing the Efficiency of the Recycling of Propylene—Polyethylene Raw Materials

NASA Astrophysics Data System (ADS)

Belokon', T. D.; Kurganova, Yu. A.; Bragin, D. A.; Kovalev, M. N.

2017-12-01

The problem of the recycling of plastic wastes is discussed. The polypropylene needs of the modern Russian market are analyzed. The necessity of recycling of plastic wastes is revealed, and its advantages over reclamation are substantiated. The problems of a real enterprise regarding the recycling of polypropylene—polyethylene raw materials for increasing the properties of the end product and optimizing its production are considered, and methods for their solution are proposed.

40 CFR 406.105 - Standards of performance for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) EFFLUENT GUIDELINES AND STANDARDS GRAIN MILLS POINT SOURCE CATEGORY Wheat Starch and Gluten Subcategory... units (kg/kkg of raw material (wheat flour)) BOD5 3.0 1.0 TSS 3.0 1.0 pH (1) (1) English units (lb/1,000 lb of raw material (wheat flour)) BOD5 3.0 1.0 TSS 3.0 1.0 pH (1) (1) 1 Within the range 6.0 to 9.0. ...

Mitigating the risk of Zika virus contamination of raw materials and cell lines in the manufacture of biologicals.

PubMed

Zmurko, Joanna; Vasey, Douglas B; Donald, Claire L; Armstrong, Alison A; McKee, Marian L; Kohl, Alain; Clayton, Reginald F

2018-02-01

Ensuring the virological safety of biologicals is challenging due to the risk of viral contamination of raw materials and cell banks, and exposure during in-process handling to known and/or emerging viral pathogens. Viruses may contaminate raw materials and biologicals intended for human or veterinary use and remain undetected until appropriate testing measures are employed. The outbreak and expansive spread of the mosquito-borne flavivirus Zika virus (ZIKV) poses challenges to screening human- and animal -derived products used in the manufacture of biologicals. Here, we report the results of an in vitro study where detector cell lines were challenged with African and Asian lineages of ZIKV. We demonstrate that this pathogen is robustly detectable by in vitro assay, thereby providing assurance of detection of ZIKV, and in turn underpinning the robustness of in vitro virology assays in safety testing of biologicals.

A Technological Comparison of Six Processes for the Production of Reduction-Grade Alumina from Non-Bauxitic Raw Materials

NASA Astrophysics Data System (ADS)

Bengtson, K. B.

The U. S. Bureau of Mines, by means of a contract with Kaiser Engineers and with Kaiser Aluminum & Chemical Corporation as a subcontractor, has sponsored a technological and an economic evaluation of six candidate processes for the manufacture of alumina from certain U. S. raw materials other than bauxite. This paper describes each process. Flow diagrams and the total energy requirement for each process are included. Important characteristics affecting the economics of producing alumina by each process are discussed, and some presently unsolved technical problems are identified. The extraction of alumina from clay via hydrochloric acid with iron separation by solvent extraction, and the crystallization of intermediate AlCl3·6H2O through the introduction of HCl gas into the pregnant mother liquor, appears to be technically feasible and the most attractive of the six raw material/process combinations.

The effect of commercial processing on the paralytic shellfish poison (PSP) content of naturally-contaminated Acanthocardia tuberculatum L.

PubMed

Berenguer, J A; Gonzalez, L; Jimenez, I; Legarda, T M; Olmedo, J B; Burdaspal, P A

1993-01-01

A study was undertaken to determine if any reduction in contamination of Acanthocardia tuberculatum L. (Mediterranean cockle) by paralytic shellfish poisons (PSP) could be enhanced by operations carried out during the industrial canning process, allowing contaminated raw material to be commercially marketed in safe conditions for edible purposes. A general decrease in PSP levels was consistently observed when comparing raw materials and their corresponding final products, these dropping to acceptable levels. PSP levels were determined by mouse bioassay and a fluorometric method, and saxitoxin was determined by HPLC. The detoxifying effects averaged over 71.7% and 81.8% (mouse bioassay), 70.6% and 90.9% (fluorometric method), 77.9% and 83.5% (HPLC), for boiling and sterilizing operations respectively. The highest level detected in raw material was 800 micrograms/100 g by mouse bioassay.

Chemical and biotechnological processing of collagen-containing raw materials into functional components of feed suitable for production of high-quality meat from farm animals

NASA Astrophysics Data System (ADS)

Baburina, M. I.; Ivankin, A. N.; Stanovova, I. A.

2017-09-01

The process of chemical biotechnological processing of collagen-containing raw materials into functional components of feeds for effective pig rearing was studied. Protein components of feeds were obtained as a result of hydrolysis in the presence of lactic acid of the animal collagen from secondary raw materials, which comprised subcutaneous collagen (cuticle), skin and veined mass with tendons from cattle. For comparison, a method is described for preparing protein components of feeds by cultivating Lactobacillus plantarum. Analysis of the kinetic data of the conversion of a high-molecular collagen protein to an aminolyte polypeptide mixture showed the advantage of microbiological synthesis in obtaining a protein for feeds. Feed formulations have been developed to include the components obtained, and which result in high quality pork suitable for the production of quality meat products.

Economic and environmental assessment of propionic acid production by fermentation using different renewable raw materials.

PubMed

Tufvesson, Pär; Ekman, Anna; Sardari, Roya R R; Engdahl, Kristina; Tufvesson, Linda

2013-12-01

Production of propionic acid by fermentation of glycerol as a renewable resource has been suggested as a means for developing an environmentally-friendly route for this commodity chemical. However, in order to quantify the environmental benefits, life cycle assessment of the production, including raw materials, fermentation, upstream and downstream processing is required. The economic viability of the process also needs to be analysed to make sure that any environmental savings can be realised. In this study an environmental and economic assessment from cradle-to-gate has been conducted. The study highlights the need for a highly efficient bioprocess in terms of product titre (more than 100g/L and productivity more than 2g/(L · h)) in order to be sustainable. The importance of the raw materials and energy production for operating the process to minimize emissions of greenhouse gases is also shown. Copyright © 2013 Elsevier Ltd. All rights reserved.

Typification of cider brandy on the basis of cider used in its manufacture.

PubMed

Rodríguez Madrera, Roberto; Mangas Alonso, Juan J

2005-04-20

A study of typification of cider brandies on the basis of the origin of the raw material used in their manufacture was conducted using chemometric techniques (principal component analysis, linear discriminant analysis, and Bayesian analysis) together with their composition in volatile compounds, as analyzed by gas chromatography with flame ionization to detect the major volatiles and by mass spectrometric to detect the minor ones. Significant principal components computed by a double cross-validation procedure allowed the structure of the database to be visualized as a function of the raw material, that is, cider made from fresh apple juice versus cider made from apple juice concentrate. Feasible and robust discriminant rules were computed and validated by a cross-validation procedure that allowed the authors to classify fresh and concentrate cider brandies, obtaining classification hits of >92%. The most discriminating variables for typifying cider brandies according to their raw material were 1-butanol and ethyl hexanoate.

On the usage of agricultural raw materials--energy or food? An assessment from an economics perspective.

PubMed

Lenk, Fabian; Bröring, Stefanie; Herzog, Philipp; Leker, Jens

2007-12-01

Bioenergies are promoted across the globe as the answer for global warming and the chance to reduce dependency from fossil energy sources. Despite the fact that renewable energy sources offer the opportunity to reduce CO2 emission and present a chance to increase agricultural incomes, they also come along with some drawbacks that have been mostly neglected in the current discussion. This paper seeks to build a basis for discussing the impacts of the growing subsidization of bioenergy and the resulting usage competition of agricultural raw materials between foods and energy. To assess the usage competition and the subsidization of bioenergy, this article employs a welfare economics perspective associated with an emphasize on the construct of externalities. This will help to foster the discussion on the further subsidization of bioenergy, where funding for R&D on new ways of using non-food raw materials ought to play a significant role.

Processing and consolidation of copper/tungsten

DOE PAGES

Chen, Ching-Fong; Pokharel, Reeju; Brand, Michael J.; ...

2016-09-27

Here, we developed a copper/tungsten (Cu/W) composite for mesoscale Materials Science applications using the novel High-Energy Diffraction Microscopy (HEDM) technique. Argon-atomized copper powder was selected as the starting raw powder and screened to remove the extremely large particle fraction. Tungsten particles were collected by milling and screening the -325 mesh tungsten powder between 500 and 635 mesh sieves. Hot pressing of screened Cu powder was performed at 900 °C in Ar/4 %H 2 atmosphere. XRD and ICP results show that the hot-pressed Cu sample consists of about 5 vol% Cu 2O, which is caused by the presence of oxygen onmore » the surface of the starting Cu powder. Hot pressing the copper powder in a pure hydrogen atmosphere was successful in removing most of the surface oxygen. Our process was also implemented for hot pressing the Cu/W composite. The density of the Cu/W composites hot pressed at 950 °C in pure hydrogen was about 94 % of the theoretical density (TD). The hot-pressed Cu/W composites were further hot isostatic pressed at 1050 °C in argon atmosphere, which results in 99.6 % of the TD with the designed Cu grain size and W particle distribution. Tensile specimens with D-notch were machined using the wire EDM method. Furthermore, the processing and consolidation of these materials will be discussed in detail. The HEDM images are also showed and discussed.« less

A Review of Pellets from Different Sources

PubMed Central

Miranda, Teresa; Montero, Irene; Sepúlveda, Francisco José; Arranz, José Ignacio; Rojas, Carmen Victoria; Nogales, Sergio

2015-01-01

The rise in pellet consumption has resulted in a wider variety of materials for pellet manufacture. Thus, pellet industry has started looking for alternative products, such as wastes from agricultural activities, forestry and related industries, along with the combination thereof, obtaining a broad range of these products. In addition, the entry into force of EN ISO 17225 standard makes wood pellet market (among other types) possible for industry and household purposes. Therefore, wastes that are suitable for biomass use have recently increased. In this study, the main characteristics of ten kinds of laboratory-made pellets from different raw materials were analyzed. Thus, we have focused on the most limiting factors of quality standards that determine the suitability for biomass market, depending on the kind of pellet. The results showed considerable differences among the analyzed pellets, exceeding the limits established by the standard in almost all cases, especially concerning ash content and N and S composition. The requirements of the studied standard, very demanding for certain factors, disable the entry of these densified wastes in greater added value markets. PMID:28788009

Sulfanilic acid-modified chitosan mini-spheres and their application for lysozyme purification from egg white.

PubMed

Hirsch, Daniela B; Baieli, María F; Urtasun, Nicolás; Lázaro-Martínez, Juan M; Glisoni, Romina J; Miranda, María V; Cascone, Osvaldo; Wolman, Federico J

2018-03-01

A cation exchange matrix with zwitterionic and multimodal properties was synthesized by a simple reaction sequence coupling sulfanilic acid to a chitosan based support. The novel chromatographic matrix was physico-chemically characterized by ss-NMR and ζ potential, and its chromatographic performance was evaluated for lysozyme purification from diluted egg white. The maximum adsorption capacity, calculated according to Langmuir adsorption isotherm, was 50.07 ± 1.47 mg g -1 while the dissociation constant was 0.074 ± 0.012 mg mL -1 . The process for lysozyme purification from egg white was optimized, with 81.9% yield and a purity degree of 86.5%, according to RP-HPLC analysis. This work shows novel possible applications of chitosan based materials. The simple synthesis reactions combined with the simple mode of use of the chitosan matrix represents a novel method to purify proteins from raw starting materials. © 2017 American Institute of Chemical Engineers Biotechnol. Prog., 34:387-396, 2018. © 2017 American Institute of Chemical Engineers.

Photoemission studies of fluorine functionalized porous graphitic carbon

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ganegoda, Hasitha; Olive, Daniel; Cheng, Lidens

2012-03-01

Porous graphitic carbon (PGC) has unique properties desirable for liquid chromatography applications when used as a stationary phase. The polar retention effect on graphite (PREG) allows efficient separation of polar and non-polar solutes. Perfluorinated hydrocarbons however lack polarizabilty and display strong lipo- and hydrophobicity, hence common lipophilic and hydrophilic analytes have low partition coefficiency in fluorinated stationary phases. Attractive interaction between fluorinated stationary phase and fluorinated analytes results in strong retention compared to non-fluorinated analytes. In order to change the selectivities of PGC, it is necessary to develop a bonded PGC stationary phase. In this study, we have synthesized perfluorinated,more » PGC using hepatadecafluoro-1-iodooctane, under different temperature conditions. Surface functionalization of the raw material was studied using photoelectron spectroscopy (PES). Results indicate the existence of fluorine containing functional groups, -CF, -CF{sub 2} along with an intercalated electron donor species. Multiple oxygen functional groups were also observed, likely due to the presence of oxygen in the starting material. These oxygen species may be responsible for significant modifications to planer and tetrahedral carbon ratios.« less

Supercapacitive behaviors and their temperature dependence of sol-gel synthesized nanostructured manganese dioxide in lithium hydroxide electrolyte

NASA Astrophysics Data System (ADS)

Wang, Xiuling; Yuan, Anbao; Wang, Yuqin

In the present work, a nanostructured manganese dioxide material was synthesized by a sol-gel method starting with manganese acetate (MnAc 2·4H 2O) and citric acid (C 6H 8O 7·H 2O) raw materials, and characterized by X-ray diffraction, infrared spectroscopic and transmission electron microscope techniques. The electrochemical properties and the influence of temperature on supercapacitive behaviors of the nano-MnO 2 electrode in 1 M LiOH electrolyte were investigated using electrochemical methods. Experimental results show that the MnO 2 electrode can exhibit an excellent pseudocapacitive behavior in 1 M LiOH electrolyte, and a high specific capacitance of 317 F g -1 can be obtained at a charge/discharge current rate of 100 mA g -1 and at the temperature of 25 °C. We found that temperature has a crucial influence on the discharge specific capacitance of the electrode. The specific capacitance at 25 °C is higher than that at 15 or 35 °C.

Correlation between hardness and water absorption properties of Saudi kaolin and white clay geopolymer coating

NASA Astrophysics Data System (ADS)

Ramasamy, Shamala; Abdullah, Mohd Mustafa Al Bakri; Huang, Yue; Hussin, Kamarudin; Wang, Jin; Shahedan, Noor Fifinatasha

2017-09-01

Geopolymer is an uprising technology that is being studied worldwide. Geopolymer raw materials are basically aluminosilicate source materials. However, this technology is yet to infiltrate into pipelines and coating industries which initiated our research idea. The idea of creating universal geopolymer based coating material is mainly to help oil and gas industry reduce its maintenance cost. Kaolin based geopolymer paste was coated on glass reinforced epoxy (GRE) substrates which are majorly used as pipeline material in the oil and gas industry at Saudi Arabia. Kaolin and white clay was chosen as raw material to study the possibilities of utilizing underused aluminosilicate raw materials for geopolymer coating. To obtain suitable formulation, Na2SiO3/NaOH ratio was varied from 0.40 untill 0.60 while other parameters such as solid/liquid ratio and NaOH molarity were kept constant at values as per previous works. Geopolymer coated GRE substrates were then subjected to water absorption, flexural strength and hardness test to validate our findings. Water absorption is a crucial test as for coating materials which justifies the pratical usability of the coating product. Upon testing, kaolin and white clay based geopolymer coating each shows promising properties at Na2SiO3/NaOH ratio of 0.45 and 0.50 each.

Correlation between thermal behavior of clays and their chemical and mineralogical composition: a review

NASA Astrophysics Data System (ADS)

Dwi Yanti, Evi; Pratiwi, I.

2018-02-01

Clay's abundance has been widely used as industrial raw materials, especially ceramic and tile industries. Utilization of these minerals needs a thermal process for producing ceramic products. Two studies conducted by Septawander et al. and Chin C et al., showed the relationship between thermal behavior of clays and their chemical and mineralogical composition. Clays are characterized by XRD analysis and thermal analysis, ranging from 1100°C to 1200°C room temperature. Specimen of raw materials of clay which is used for the thermal treatment is taken from different geological conditions and formation. In raw material, Quartz is almost present in all samples. Halloysite, montmorillonite, and feldspar are present in Tanjung Morawa raw clay. KC and MC similar kaolinite and illite are present in the samples. The research illustrates the interrelationships of clay minerals and chemical composition with their heat behavior. As the temperature of combustion increases, the sample reduces a significant weight. The minerals which have undergone a transformation phase became mullite, cristobalite or illite and quartz. Under SEM analysis, the microstructures of the samples showed irregularity in shape; changes occurred due the increase of heat.

[Plants' materials and synthetic agonists of cannabinoid receptors use as a substitute of Marihuana, appearing in a current forensic toxicology practice of evidence materials].

PubMed

Geppert, Bogna; Tezyk, Artur; Florek, Ewa; Zaba, Czesław

2010-01-01

Cannabis sativa species Indica (Marihuana) is nowadays one of the most common plant drug, with psychoactive activity, presently appearing on the illegal market in Poland. It is reported that frequency of securing evidential materials so called substitute of Marihuana, is growing rapidly during the last few years. The substitutes of Marihuana occurring on the market are of natural or synthetic origins, for example different species of raw plants' materials having action similar to Cannabis or raw plants' materials with no psychoactive properities but with an addition of components so called synthetic cannabinoids. The review presents recent developments in drug market and current problems of forensic toxicology on the example of Marihuana.

48 CFR 52.211-5 - Material Requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 48 Federal Acquisition Regulations System 2 2012-10-01 2012-10-01 false Material Requirements. 52....211-5 Material Requirements. As prescribed in 11.304, insert the following clause: Material... components, whether manufactured from virgin material, recovered material in the form of raw material, or...

48 CFR 52.211-5 - Material Requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 48 Federal Acquisition Regulations System 2 2014-10-01 2014-10-01 false Material Requirements. 52....211-5 Material Requirements. As prescribed in 11.304, insert the following clause: Material... components, whether manufactured from virgin material, recovered material in the form of raw material, or...

The Use of Combustion Reactions for Processing Mineral Raw Materials: Metallothermy and Self-propagating High-temperature Synthesis (Review)

NASA Astrophysics Data System (ADS)

Urakaev, Farit Kh.; Akmalaev, Kenzhebek A.; Orynbekov, Eljan S.; Balgysheva, Beykut D.; Zharlykasimova, Dinar N.

2016-02-01

The use of metallothermy (MT) and self-propagating high-temperature synthesis (SHS) is considered for processing different geological and technogenic materials. Traditional MT and SHS processes for production of various metals and nonmetal materials are widely known. Another rapidly developing direction is that connected with the use of ores, concentrates, minerals, and technogenic waste products as one of the components of a thermite mixture, both for the treatment of mineral raw by means of MT or SHS resulting in semi-products and for technological, analytical, and ecological purposes.

77 FR 16262 - Importer of Controlled Substances, Notice of Registration; Johnson Matthey, Inc., Pharmaceutical...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-20

... substances: Drug Schedule Coca Leaves (9040) II Thebaine (9333) II Opium, raw (9600) II Noroxymorphone (9668... raw materials, to be used in the manufacture of bulk controlled substances, for distribution to its customers. In regard [[Page 16263

The Pattern of Soviet Conduct in the Third World, Review and Preview. Part I

DTIC Science & Technology

1983-03-07

vital raw materials is concerned. This interest relates however above all to the rich, oil -producing countries, whereas the East German and Cuban...was economic - the extraction of cheap raw materials and the wish to find markets. Nor is it true, as he predicted, that the. imperialist powers...disappointment in the non- oil producing Third World countries than should have been expected because the Soviet leaders never made excessive. promises. They

20th century U.S. mineral prices decline in constant dollars

USGS Publications Warehouse

Sullivan, Daniel E.; Sznopek, John L.; Wagner, Lorie A.

2000-01-01

Price indexes developed by the U.S. Geological Survey (USGS) indicate that the long-term constant dollar price of key U.S. mineral raw materials declined over the last century, even though the need for mineral raw materials increased during the same period. Technologies and reduced production costs have allowed mineral production to remain profitable, while lower priced mineral products from domestic and foreign sources helped fuel growth in other sectors of the economy.

Selected Translations on East European Foreign Trade, Number 5.

DTIC Science & Technology

1961-08-31

Bulgaria, openly prefer these raw materials, mainly grain, livestock for meat, and scarce oil - seeds , but show very little interest in, for instance...over I960 — for imports from the USSR of fuel raw mineral materials, and metals. This is because the quantities of oil derivatives and cast iron are...metals will increase by 28 percent because of the enlarged contingents of oil and manganese ore Consumer goods show a more significant growth, as

40 CFR 406.102 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GRAIN MILLS POINT SOURCE CATEGORY Wheat Starch and...— Metric units (kg/kkg of raw material (wheat flour)) BOD5 6.0 2.0 TSS 6.0 2.0 pH (1) (1) English units (lb/1,000 lb of raw material (wheat flour)) BOD5 6.0 2.0 TSS 6.0 2.0 pH (1) (1) 1 Within the range 6.0...

Utilization of household food waste for the production of ethanol at high dry material content.

PubMed

Matsakas, Leonidas; Kekos, Dimitris; Loizidou, Maria; Christakopoulos, Paul

2014-01-08

Environmental issues and shortage of fossil fuels have turned the public interest to the utilization of renewable, environmentally friendly fuels, such as ethanol. In order to minimize the competition between fuels and food production, researchers are focusing their efforts to the utilization of wastes and by-products as raw materials for the production of ethanol. household food wastes are being produced in great quantities in European Union and their handling can be a challenge. Moreover, their disposal can cause severe environmental issues (for example emission of greenhouse gasses). On the other hand, they contain significant amounts of sugars (both soluble and insoluble) and they can be used as raw material for the production of ethanol. Household food wastes were utilized as raw material for the production of ethanol at high dry material consistencies. A distinct liquefaction/saccharification step has been included to the process, which rapidly reduced the viscosity of the high solid content substrate, resulting in better mixing of the fermenting microorganism. This step had a positive effect in both ethanol production and productivity, leading to a significant increase in both values, which was up to 40.81% and 4.46 fold, respectively. Remaining solids (residue) after fermentation at 45% w/v dry material (which contained also the unhydrolyzed fraction of cellulose), were subjected to a hydrothermal pretreatment in order to be utilized as raw material for a subsequent ethanol fermentation. This led to an increase of 13.16% in the ethanol production levels achieving a final ethanol yield of 107.58 g/kg dry material. In conclusion, the ability of utilizing household food waste for the production of ethanol at elevated dry material content has been demonstrated. A separate liquefaction/saccharification process can increase both ethanol production and productivity. Finally, subsequent fermentation of the remaining solids could lead to an increase of the overall ethanol production yield.

Utilization of household food waste for the production of ethanol at high dry material content

PubMed Central

2014-01-01

Background Environmental issues and shortage of fossil fuels have turned the public interest to the utilization of renewable, environmentally friendly fuels, such as ethanol. In order to minimize the competition between fuels and food production, researchers are focusing their efforts to the utilization of wastes and by-products as raw materials for the production of ethanol. household food wastes are being produced in great quantities in European Union and their handling can be a challenge. Moreover, their disposal can cause severe environmental issues (for example emission of greenhouse gasses). On the other hand, they contain significant amounts of sugars (both soluble and insoluble) and they can be used as raw material for the production of ethanol. Results Household food wastes were utilized as raw material for the production of ethanol at high dry material consistencies. A distinct liquefaction/saccharification step has been included to the process, which rapidly reduced the viscosity of the high solid content substrate, resulting in better mixing of the fermenting microorganism. This step had a positive effect in both ethanol production and productivity, leading to a significant increase in both values, which was up to 40.81% and 4.46 fold, respectively. Remaining solids (residue) after fermentation at 45% w/v dry material (which contained also the unhydrolyzed fraction of cellulose), were subjected to a hydrothermal pretreatment in order to be utilized as raw material for a subsequent ethanol fermentation. This led to an increase of 13.16% in the ethanol production levels achieving a final ethanol yield of 107.58 g/kg dry material. Conclusions In conclusion, the ability of utilizing household food waste for the production of ethanol at elevated dry material content has been demonstrated. A separate liquefaction/saccharification process can increase both ethanol production and productivity. Finally, subsequent fermentation of the remaining solids could lead to an increase of the overall ethanol production yield. PMID:24401142

Assessment of emissions and removal of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) at start-up periods in a hazardous waste incinerator.

PubMed

Karademir, Aykan; Korucu, M Kemal

2013-07-01

A study was conducted to observe the changes in polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/F) levels and congener profiles in the flue gas of a hazardous waste incinerator during two start-up periods. Flue gas samplings were performed simultaneously through Air Pollution Control Devices (APCDs) (including boiler outlet, electrostatic precipitator (ESP) outlet, wet scrubbers (WS) outlet, and activated carbon (AC) filter outlet) in different combustion temperatures during a planned cold (long) start-up and an unplanned warm (short) start-up. The results showed that PCDD/F concentrations could be elevated during the start-up periods up to levels 3-4 times higher than those observed in the normal operation. Especially lower combustion temperatures in the short start-ups may cause high PCDD/F concentrations in the raw flue gas. Assessment of combustion temperatures and Furans/Dioxins values indicated that surface-catalyzed de novo synthesis was the dominant pathway in the formation of PCDD/Fs in the combustion units. PCDD/F removal efficiencies of Air Pollution Control Devices suggested that formation by de novo synthesis existed in ESP also when in operation, leading to increase of gaseous phase PCDD/Fs in ESP Particle-bound PCDD/Fs were removed mainly by ESP and WS, while gaseous phase PCDD/Fs were removed by WS, and more efficiently by AC filter. This paper evaluates PCDD/F emissions and removal performances of APCDs (ESP, wet scrubbers, and activated carbon) during two start-up periods in an incinerator. The main implications are the following: (1) start-up periods increase PCDD/F emissions up to 2-3 times in the incinerator; (2) low combustion temperatures in start-ups cause high PCDD/F emissions in raw gas; (3) formation of PCDD/Fs by de novo synthesis occurs in ESP; (4) AC is efficient in removing gaseous PCDD/Fs, but may increase particle-bound ones; and (5) scrubbers remove both gaseous and particle-bound PCDD/Fs efficiently.

An ethnobotanical survey of medicinal plants of Laos toward the discovery of bioactive compounds as potential candidates for pharmaceutical development

PubMed Central

Soejarto, D.D.; Gyllenhaal, C.; Kadushin, M.R.; Southavong, B.; Sydara, K.; Bouamanivong, S.; Xaiveu, M.; Zhang, H.-J.; Franzblau, S.G.; Tan, Ghee T.; Pezzuto, J.M.; Riley, M.C.; Elkington, B.G.; Waller, D.P.

2012-01-01

Context An ethnobotany-based approach in the selection of raw plant materials to study was implemented. Objective To acquire raw plant materials using ethnobotanical field interviews as starting point to discover new bioactive compounds from medicinal plants of the Lao People’s Democratic Republic. Methods Using semi-structured field interviews with healers in the Lao PDR, plant samples were collected, extracted, and bio-assayed to detect bioactivity against cancer, HIV/AIDS, TB, malaria. Plant species demonstrating activity were recollected and the extracts subjected to a bioassay-guided isolation protocol to isolate and identify the active compounds. Results Field interviews with 118 healers in 15 of 17 provinces of Lao PDR yielded 753 collections (573 species) with 955 plant samples. Of these 955, 50 extracts demonstrated activity in the anticancer, 10 in the anti-HIV, 30 in the anti-TB, and 52 in the antimalarial assay. Recollection of actives followed by bioassay-guided isolation processes yielded a series of new and known in vitro-active anticancer and antimalarial compounds from 5 species. Discussion Laos has a rich biodiversity, harboring an estimated 8000–11,000 species of plants. In a country highly dependent on traditional medicine for its primary health care, this rich plant diversity serves as a major source of their medication. Conclusions Ethnobotanical survey has demonstrated the richness of plant-based traditional medicine of Lao PDR, taxonomically and therapeutically. Biological assays of extracts of half of the 955 samples followed by in-depth studies of a number of actives have yielded a series of new bioactive compounds against the diseases of cancer and malaria. PMID:22136442

Cultivation of Cimicifuga racemosa (L.) nuttal and quality of CR extract BNO 1055.

PubMed

Popp, Michael; Schenk, Regina; Abel, Gudrun

2003-03-14

For Cimicifuga racemosa, well-founded investigations concerning multiplication, germination of seeds and field cultivation have not yet been published. Defined origins or varieties with certain agronomic properties and a specific pattern of active compounds are not commercially available. Special challenges are found with regard to growing of young plantlets from seeds. Comprehensive investigations have been started to find optimal conditions for all steps of the whole process to establish cultivation for Cimicifuga. Aim is to get defined varieties or sources with desirable agronomic characteristics and specific reproducible compound patterns in order to reach homogeneous plant raw material. For analytical tests, validated HPLC and TLC methods were used. Results from germination experiments with different temperature regimens show that the time for germination can be shortened from about 20 months to about 6 months. Gibberellic acid had positive influence on the development of the embryo. Content of triterpenglycosides and phenolic compounds was highest in May and June and decreased then from July until September. The quality of the ethanolic extract BNO 1055 (contained in Klimadynon(R) and Menofem(R)) differs from that of an isopropanolic extract. Comparison was carried out by means of TLC pattern of triterpenglycosides and phenolic compounds. Extensive systematic research on cultivation parameters with regard to all stages from the seeds to the herbal drug enables commercial field cultivation of Cimicifuga. Controlled cultivation (according to good agricultural practice or GAP) ensures the availability of homogenous standardized raw material. For pharmacological and clinical studies, standardized extracts and finished herbal medicinal products are required. Results of these studies are never transferable to other products and therefore valid only for the tested extracts/products.

Energy-saving drying and its application

NASA Astrophysics Data System (ADS)

Kovbasyuk, V. I.

2015-09-01

Superheated steam is efficiently applied as a coolant for the intensification of drying, which is an important component of many up-to-date technologies. However, traditional drying is extremely energy consuming, and many drying apparatus are environmentally unfriendly. Thus, it is important to implement the proposed drying technique using superheated steam under pressure significantly higher than the atmospheric one with subsequent steam transfer for use in a turbine for electric power generation as a compensation of energy costs for drying. This paper includes a brief thermodynamic analysis of such a technique, its environmental advantages, and possible benefits of the use of wet wastes and obtaining high-quality fuels from wet raw materials. A scheme is developed for the turbine protection from impurities that can occur in the steam at drying. Potential advantage of the technique are also the absence of heating surfaces that are in contact with wet media, the absence of the emissions to the atmosphere, and the use of low potential heat for desalination and the purification of water. The new drying technique can play an extremely important part in the implementation in the field of thermal destruction of anthropogenic wastes. In spite of the promotion of waste sorting to obtain valuable secondary raw materials, the main problem of big cities is nonutilizable waste, which makes not less than 85% of the starting quantity of waste. This can only be totally solved by combustion, which even more relates to the sewage sludge utilization. The wastes can be safely and efficiently combusted only provided that they are free of moisture. Combustion temperature optimization makes possible full destruction of dioxins and their toxic analogues.

Analytical methods to characterize heterogeneous raw material for thermal spray process: cored wire Inconel 625

NASA Astrophysics Data System (ADS)

Lindner, T.; Bonebeau, S.; Drehmann, R.; Grund, T.; Pawlowski, L.; Lampke, T.

2016-03-01

In wire arc spraying, the raw material needs to exhibit sufficient formability and ductility in order to be processed. By using an electrically conductive, metallic sheath, it is also possible to handle non-conductive and/or brittle materials such as ceramics. In comparison to massive wire, a cored wire has a heterogeneous material distribution. Due to this fact and the complex thermodynamic processes during wire arc spraying, it is very difficult to predict the resulting chemical composition in the coating with sufficient accuracy. An Inconel 625 cored wire was used to investigate this issue. In a comparative study, the analytical results of the raw material were compared to arc sprayed coatings and droplets, which were remelted in an arc furnace under argon atmosphere. Energy-dispersive X-ray spectroscopy (EDX) and X-ray fluorescence (XRF) analysis were used to determine the chemical composition. The phase determination was performed by X-ray diffraction (XRD). The results were related to the manufacturer specifications and evaluated in respect to differences in the chemical composition. The comparison between the feedstock powder, the remelted droplets and the thermally sprayed coatings allows to evaluate the influence of the processing methods on the resulting chemical and phase composition.

Discriminative illumination: per-pixel classification of raw materials based on optimal projections of spectral BRDF.

PubMed

Liu, Chao; Gu, Jinwei

2014-01-01

Classifying raw, unpainted materials--metal, plastic, ceramic, fabric, and so on--is an important yet challenging task for computer vision. Previous works measure subsets of surface spectral reflectance as features for classification. However, acquiring the full spectral reflectance is time consuming and error-prone. In this paper, we propose to use coded illumination to directly measure discriminative features for material classification. Optimal illumination patterns--which we call "discriminative illumination"--are learned from training samples, after projecting to which the spectral reflectance of different materials are maximally separated. This projection is automatically realized by the integration of incident light for surface reflection. While a single discriminative illumination is capable of linear, two-class classification, we show that multiple discriminative illuminations can be used for nonlinear and multiclass classification. We also show theoretically that the proposed method has higher signal-to-noise ratio than previous methods due to light multiplexing. Finally, we construct an LED-based multispectral dome and use the discriminative illumination method for classifying a variety of raw materials, including metal (aluminum, alloy, steel, stainless steel, brass, and copper), plastic, ceramic, fabric, and wood. Experimental results demonstrate its effectiveness.

75 FR 28751 - Airworthiness Directives; Bell Helicopter Textron (Bell) Model 205A, 205A-1, 205B, 212, 412...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-24

... the raw material used in manufacturing certain crosstubes. The actions specified in this AD are... these model helicopters. This amendment is prompted by AAI's discovery of a defect in a batch of raw...

40 CFR 63.1352 - Additional test methods.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Standards for Hazardous Air Pollutants From the Portland Cement Manufacturing Industry Monitoring and... rates of emission of HCl from kilns and associated bypass stacks at portland cement manufacturing... specific organic HAP from raw material dryers, kilns and in-line kiln/raw mills at Portland cement...

40 CFR 63.1352 - Additional test methods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Standards for Hazardous Air Pollutants From the Portland Cement Manufacturing Industry Monitoring and... rates of emission of HCl from kilns and associated bypass stacks at portland cement manufacturing... specific organic HAP from raw material dryers, kilns and in-line kiln/raw mills at Portland cement...

Bright Side of Lignin Depolymerization: Toward New Platform Chemicals

PubMed Central

2018-01-01

Lignin, a major component of lignocellulose, is the largest source of aromatic building blocks on the planet and harbors great potential to serve as starting material for the production of biobased products. Despite the initial challenges associated with the robust and irregular structure of lignin, the valorization of this intriguing aromatic biopolymer has come a long way: recently, many creative strategies emerged that deliver defined products via catalytic or biocatalytic depolymerization in good yields. The purpose of this review is to provide insight into these novel approaches and the potential application of such emerging new structures for the synthesis of biobased polymers or pharmacologically active molecules. Existing strategies for functionalization or defunctionalization of lignin-based compounds are also summarized. Following the whole value chain from raw lignocellulose through depolymerization to application whenever possible, specific lignin-based compounds emerge that could be in the future considered as potential lignin-derived platform chemicals. PMID:29337543

Antimicrobial Effect of Nisin against Bacillus cereus in Beef Jerky during Storage

PubMed Central

Lee, Na-Kyoung; Kim, Hyoun Wook; Lee, Joo Yeon; Ahn, Dong Uk; Kim, Cheon-Jei; Paik, Hyun-Dong

2015-01-01

The microbial distribution of raw materials and beef jerky, and the effect of nisin on the growth of Bacillus cereus inoculated in beef jerky during storage, were studied. Five strains of pathogenic B. cereus were detected in beef jerky, and identified with 99.8% agreement using API CHB 50 kit. To evaluate the effect of nisin, beef jerky was inoculated with approximately 3 Log CFU/g of B. cereus mixed culture and nisin (100 IU/g and 500 IU/g). During the storage of beef jerky without nisin, the number of mesophilic bacteria and B. cereus increased unlikely for beef jerky with nisin. B. cereus started to grow after 3 d in 100 IU nisin/g treatment, and after 21 d in 500 IU nisin/g treatment. The results suggest that nisin could be an effective approach to extend the shelf-life, and improve the microbial safety of beef jerky, during storage. PMID:26761838

The joint Australia/Federal Republic of Germany feasibility study on the conversion of Australian coals into liquid fuels in Australia

NASA Astrophysics Data System (ADS)

Imhausen, K. H.

1982-08-01

The IG hydrogenation process used commercially in Germany up to 1945, was improved. Pilot plants in Germany are presently under construction or in the start-up phase. A technical concept for the conversion of Australian bituminous coals and/or Australian brown coals into automotive fuels, using coal hydrogenation, gasification and Fisher-Tropsch synthesis was developed. Development of technology, consumption figures and of expenditure/investment for a complete plant, producing about 3 million tons of automotive fuels per year, was also attempted. The results show that standard automotive fuels are produced from bituminous coal, using a combination of high pressure coal hydrogenation and of Fisher-Tropsch synthesis, and from brown coal, using high pressure coal hydrogenation only. Under the assumption that crude oil prices increase 3% more rapidly than yearly inflation, and the raw material cost are staying at a low level, commercial plants are planned.

Study of Catalyst Variation Effect in Glycerol Conversion Process to Hydrogen Gas by Steam Reforming

NASA Astrophysics Data System (ADS)

Widayat; Hartono, R.; Elizabeth, E.; Annisa, A. N.

2018-04-01

Along with the economic development, needs of energy being increase too. Hydrogen as alternative energy has many usages. Besides that, hydrogen is one source of energy that is a clean fuel, but process production of hydrogen from natural gas as a raw material has been used for a long time. Therefore, there is need new invention to produce hydrogen from the others raw material. Glycerol, a byproduct of biodiesel production, is a compound which can be used as a raw material for hydrogen production. By using glycerol as a raw material of hydrogen production, we can get added value of glycerol as well as an energy source solution. The process production of hydrogen by steam reforming is a thermochemical process with efficiency 70%. This process needs contribution of catalyst to improve its efficiency and selectivity of the process. In this study will be examined the effect variation of catalyst for glycerol conversion process to hydrogen by steam reforming. The method for catalyst preparation was variation of catalyst impregnation composition, catalyst calcined with difference concentration of hydrochloric acid and calcined with difference hydrochloric acid ratio. After that, all of catalyst which have been prepared, used for steam reforming process for hydrogen production from glycerol as a raw material. From the study, the highest yield of hydrogen gas showed in the process production by natural zeolite catalyst with 1:15 Hydrochloric acid ratio was 42.28%. Hydrogen yield for 2M calcined natural zeolite catalyst was 38.37%, for ZSM-5 catalyst was 15.83%, for 0.5M calcined natural zeolite was 13.09% and for ultrasonic natural zeolite was 11.43%. The lowest yield of hydrogen gas showed in catalyst 2Zn/ZSM-5 with 11.22%. This result showed that hydrogen yield product was affected by catalyst variation because of the catalyst has difference characteristic and difference catalytic activity after the catalyst preparation process.

Microbiological sampling plan based on risk classification to verify supplier selection and production of served meals in food service operation.

PubMed

Lahou, Evy; Jacxsens, Liesbeth; Van Landeghem, Filip; Uyttendaele, Mieke

2014-08-01

Food service operations are confronted with a diverse range of raw materials and served meals. The implementation of a microbial sampling plan in the framework of verification of suppliers and their own production process (functionality of their prerequisite and HACCP program), demands selection of food products and sampling frequencies. However, these are often selected without a well described scientifically underpinned sampling plan. Therefore, an approach on how to set-up a focused sampling plan, enabled by a microbial risk categorization of food products, for both incoming raw materials and meals served to the consumers is presented. The sampling plan was implemented as a case study during a one-year period in an institutional food service operation to test the feasibility of the chosen approach. This resulted in 123 samples of raw materials and 87 samples of meal servings (focused on high risk categorized food products) which were analyzed for spoilage bacteria, hygiene indicators and food borne pathogens. Although sampling plans are intrinsically limited in assessing the quality and safety of sampled foods, it was shown to be useful to reveal major non-compliances and opportunities to improve the food safety management system in place. Points of attention deduced in the case study were control of Listeria monocytogenes in raw meat spread and raw fish as well as overall microbial quality of served sandwiches and salads. Copyright © 2014 Elsevier Ltd. All rights reserved.

Laboratory-scale study of possible use of residual sludge from glass sand beneficiation

NASA Astrophysics Data System (ADS)

Prikryl, Richard; Weishauptova, Zuzana; Zach, Jaroslav; Kozlovcev, Petr

2016-04-01

Beneficiation of quartz sand from sedimentary deposits for glass sands results in significant amounts of under-size fraction, a sludge rich in clay minerals. This sludge is considered as a waste and is returned in mined-out spaces for a simple rehabilitation, which is also the case of one of the largest glass sand production areas in the Czech Republic. The amount of produced waste sludge in the studied area (glass sand works in Provodín area, Bohemian Cretaceous Basin) is about 20 kt per year. In the recent study, we have focused on possible employment of this waste material for three applications: (1) a clay component in a raw material mixture for making of hydraulic lime, (2) a kaolinite absorbent, and (3) a geotechnical material. The sampled sludge was primarily analysed for mineralogical and chemical composition, mechanical and physical properties, the specific surface area, and parameters of pore space. X-ray analysis proved the presence of kaolinite, illite (both WCI and PCI), quartz, and accessory microcline. According to silicate analysis, the material is composed of SiO2 (80.52 wt. %), Al2O3 (11.36 wt. %), and K2O (2.14 wt. %). For its potential use as an artificial admixture for hydraulic lime production, the studied material was mixed with pure limestone in ratio of 10, 15, 20, and/or 25 wt. %. The experimental mixtures were burnt in the temperature range from 850 to 1,200°C. XRD was employed for the detection of newly formed phases showing formation of hydraulic phase such as C2S, C3A, C4AF starting from the 1050°C burning temperature. Peak burning temperature significantly influenced amount of individual phases in the burnt product. Second possible mode of use of the investigated waste material focused on its application as a sorbent. Pore space and specific surface area characteristics (SBET 7.4 sq. m/g) range this material to the group of low grade kaolinite-dominated adsorbents. Thermal treatment (burning of raw waste material at temperatures of 500°C and/or 900°C) lead to rapid deterioration of specific surface area, probably due to the structural and phase changes of dominant clay minerals. The latest considered use in the field of geotechnical applications proved possible employment of the studied material as a sealing clay for smaller dams, ponds and/or as a geotechnical barrier for waste dumps.

Assessment of Damage Tolerance Requirements and Analysis. Volume 4. Raw Test Data

DTIC Science & Technology

1986-03-31

T3XX aluminum alloy . Four (4) product forms were selected: MATERIAL PRODUCT FORM THICKNESS (IN) 2024-T3 Sheet 0.090, 0.190 2024-T351 Plate 0.250 2024...T3511 Extruded Tee 0.190 2024-T3511 Extruded Angle 0.250 The material selected to represent bomber/transport/cargo aircraft is 7075- T6XX aluminum alloy ...aluminum alloys , respectively. The raw test data were processed in accordance with ASTM Standard E-8. All the tensile properties, except those marked

Recoveries raw data

EPA Pesticide Factsheets

Dataset shows the calculation of reported decontamination efficacies from the raw data (i.e., measured amount of chemical recovered from test coupons and positive controls) to actual decontamination efficacy for all chemicals and decontaminantsThis dataset is associated with the following publication:Oudejans , L., J. O'Kelly, A. Evans, B. Barbara Wyrzykowska-Ceradini, A. Toauati, D. Tabor , and E. Snyder. Efficacy of decontaminant solutions for remediation on TICs on PPE materials. JOURNAL OF HAZARDOUS MATERIALS. Elsevier Science Ltd, New York, NY, USA, 1-5, (2016).

Verification of vermural stabilization of ash from biomass and sewage sludge

NASA Astrophysics Data System (ADS)

Adamkova, L.; Kucerova, D.; Lyckova, B.; Kucerova, R.; Takac, D.

2017-10-01

The aim of this study was to find dependence on biofuels and sludge from sewage treatment plants in the vermicomposting process. In the framework of the research carried out at our workplace, a project aimed at finding an appropriate method for the reprocessing of problematic biodegradable waste and asphalt from combustion biomass was used as a raw material for the production of rectification substrate and sludge from sewage treatment plants that could be used as Secondary raw material.

Evaluation of the innate immune-stimulating activity of amazake using a silkworm muscle contraction assay.

PubMed

Maruki-Uchida, Hiroko; Sai, Masahiko; Sekimizu, Kazuhisa

2017-11-22

We evaluated the innate immune-stimulating activity of amazake using a silkworm muscle contraction assay. Sake cake, a raw material used to make amazake, had high innate immunity-stimulating activity, whereas rice malt, another raw material used to make amazake, did not, even after fermentation. These results suggest that the silkworm muscle contraction assay is a useful tool to screen foods with high innate immune-stimulating activity and that amazake made from sake cake has immunomodulatory potential.

Toward the Printed World: Additive Manufacturing and Implications for National Security (Defense Horizons, Number 73)

DTIC Science & Technology

2012-09-01

allowing it to dry or baking it in a kiln . A modern factory would take a block of raw material and then use machinery to pare away un- necessary... conventional “subtractive manu- facturing”—taking a block of raw material and removing excess until the finished product remains—the process as a whole...is more efficient and less wasteful. Another major benefit of AM is the fact that com- plexity is “free.” In conventional manufacturing, increasing

Study of Pellets and Lumps as Raw Materials in Silicon Production from Quartz and Silicon Carbide

NASA Astrophysics Data System (ADS)

Dal Martello, E.; Tranell, G.; Gaal, S.; Raaness, O. S.; Tang, K.; Arnberg, L.

2011-10-01

The use of high-purity carbon and quartz raw materials reduces the need for comprehensive refining steps after the silicon has been produced carbothermically in the electric reduction furnace. The current work aims at comparing the reaction mechanisms and kinetics occurring in the inner part of the reduction furnace when pellets or lumpy charge is used, as well as the effect of the raw material mix. Laboratory-scale carbothermic reduction experiments have been carried out in an induction furnace. High-purity silicon carbide and two different high-purity hydrothermal quartzes were charged as raw materials at different molar ratios. The charge was in the form of lumps (size, 2-5 mm) or as powder (size, 10-20 μm), mixed and agglomerated as pellets (size, 1-3 mm) and reacted at 2273 K (2000 °C). The thermal properties of the quartzes were measured also by heating a small piece of quartz in CO atmosphere. The investigated quartzes have different reactivity in reducing atmosphere. The carbothermal reduction experiments show differences in the reacted charge between pellets and lumps as charge material. Solid-gas reactions take place from the inside of the pellets porosity, whereas reactions in lumps occur topochemically. Silicon in pellets is produced mainly in the rim zone. Larger volumes of silicon have been found when using lumpy charge. More SiO is produced when using pellets than for lumpy SiO2 for the same molar ratio and heating conditions. The two SiC polytypes used in the carbothermal reduction experiments as carbon reductants presented different reactivity.

Fueling industrial biotechnology growth with bioethanol.

PubMed

Otero, José Manuel; Panagiotou, Gianni; Olsson, Lisbeth

2007-01-01

Industrial biotechnology is the conversion of biomass via biocatalysis, microbial fermentation, or cell culture to produce chemicals, materials, and/or energy. Industrial biotechnology processes aim to be cost-competitive, environmentally favorable, and self-sustaining compared to their petrochemical equivalents. Common to all processes for the production of energy, commodity, added value, or fine chemicals is that raw materials comprise the most significant cost fraction, particularly as operating efficiencies increase through practice and improving technologies. Today, crude petroleum represents the dominant raw material for the energy and chemical sectors worldwide. Within the last 5 years petroleum prices, stability, and supply have increased, decreased, and been threatened, respectively, driving a renewed interest across academic, government, and corporate centers to utilize biomass as an alternative raw material. Specifically, bio-based ethanol as an alternative biofuel has emerged as the single largest biotechnology commodity, with close to 46 billion L produced worldwide in 2005. Bioethanol is a leading example of how systems biology tools have significantly enhanced metabolic engineering, inverse metabolic engineering, and protein and enzyme engineering strategies. This enhancement stems from method development for measurement, analysis, and data integration of functional genomics, including the transcriptome, proteome, metabolome, and fluxome. This review will show that future industrial biotechnology process development will benefit tremendously from the precedent set by bioethanol - that enabling technologies (e.g., systems biology tools) coupled with favorable economic and socio-political driving forces do yield profitable, sustainable, and environmentally responsible processes. Biofuel will continue to be the keystone of any industrial biotechnology-based economy whereby biorefineries leverage common raw materials and unit operations to integrate diverse processes to produce demand-driven product portfolios.

Performance of food safety management systems in poultry meat preparation processing plants in relation to Campylobacter spp. contamination.

PubMed

Sampers, Imca; Jacxsens, Liesbeth; Luning, Pieternel A; Marcelis, Willem J; Dumoulin, Ann; Uyttendaele, Mieke

2010-08-01

A diagnostic instrument comprising a combined assessment of core control and assurance activities and a microbial assessment instrument were used to measure the performance of current food safety management systems (FSMSs) of two poultry meat preparation companies. The high risk status of the company's contextual factors, i.e., starting from raw materials (poultry carcasses) with possible high numbers and prevalence of pathogens such as Campylobacter spp., requires advanced core control and assurance activities in the FSMS to guarantee food safety. The level of the core FSMS activities differed between the companies, and this difference was reflected in overall microbial quality (mesophilic aerobic count), presence of hygiene indicators (Enterobacteriaceae, Staphylococcus aureus, and Escherichia coli), and contamination with pathogens such as Salmonella, Listeria monocytogenes, and Campylobacter spp. The food safety output expressed as a microbial safety profile was related to the variability in the prevalence and contamination levels of Campylobacter spp. in poultry meat preparations found in a Belgian nationwide study. Although a poultry meat processing company could have an advanced FSMS in place and a good microbial profile (i.e., lower prevalence of pathogens, lower microbial numbers, and less variability in microbial contamination), these positive factors might not guarantee pathogen-free products. Contamination could be attributed to the inability to apply effective interventions to reduce or eliminate pathogens in the production chain of (raw) poultry meat preparations.

Particle size distribution: A key factor in estimating powder dustiness.

PubMed

López Lilao, Ana; Sanfélix Forner, Vicenta; Mallol Gasch, Gustavo; Monfort Gimeno, Eliseo

2017-12-01

A wide variety of raw materials, involving more than 20 samples of quartzes, feldspars, nephelines, carbonates, dolomites, sands, zircons, and alumina, were selected and characterised. Dustiness, i.e., a materials' tendency to generate dust on handling, was determined using the continuous drop method. These raw materials were selected to encompass a wide range of particle sizes (1.6-294 µm) and true densities (2650-4680 kg/m 3 ). The dustiness of the raw materials, i.e., their tendency to generate dust on handling, was determined using the continuous drop method. The influence of some key material parameters (particle size distribution, flowability, and specific surface area) on dustiness was assessed. In this regard, dustiness was found to be significantly affected by particle size distribution. Data analysis enabled development of a model for predicting the dustiness of the studied materials, assuming that dustiness depended on the particle fraction susceptible to emission and on the bulk material's susceptibility to release these particles. On the one hand, the developed model allows the dustiness mechanisms to be better understood. In this regard, it may be noted that relative emission increased with mean particle size. However, this did not necessarily imply that dustiness did, because dustiness also depended on the fraction of particles susceptible to be emitted. On the other hand, the developed model enables dustiness to be estimated using just the particle size distribution data. The quality of the fits was quite good and the fact that only particle size distribution data are needed facilitates industrial application, since these data are usually known by raw materials managers, thus making additional tests unnecessary. This model may therefore be deemed a key tool in drawing up efficient preventive and/or corrective measures to reduce dust emissions during bulk powder processing, both inside and outside industrial facilities. It is recommended, however, to use the developed model only if particle size, true density, moisture content, and shape lie within the studied ranges.

40 CFR 409.31 - Specialized definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.31 Specialized... shall mean the addition of pollutants. (c) Melt shall mean that amount of raw material (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

40 CFR 409.31 - Specialized definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.31 Specialized... shall mean the addition of pollutants. (c) Melt shall mean that amount of raw material (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

40 CFR 409.31 - Specialized definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.31 Specialized... shall mean the addition of pollutants. (c) Melt shall mean that amount of raw material (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

40 CFR 409.31 - Specialized definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.31 Specialized... shall mean the addition of pollutants. (c) Melt shall mean that amount of raw material (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

48 CFR 31.205-26 - Material costs.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 48 Federal Acquisition Regulations System 1 2014-10-01 2014-10-01 false Material costs. 31.205-26....205-26 Material costs. (a) Material costs include the costs of such items as raw materials, parts... material costs, the contractor shall consider reasonable overruns, spoilage, or defective work (unless...

48 CFR 31.205-26 - Material costs.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 48 Federal Acquisition Regulations System 1 2013-10-01 2013-10-01 false Material costs. 31.205-26....205-26 Material costs. (a) Material costs include the costs of such items as raw materials, parts... material costs, the contractor shall consider reasonable overruns, spoilage, or defective work (unless...

48 CFR 52.211-5 - Material Requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... readjustments and material replacement. Recovered material means waste materials and by-products recovered or diverted from solid waste, but the term does not include those materials and by-products generated from... is, or with new technology will become, a source of raw materials. (b) Unless this contract otherwise...

Methods for the additive manufacturing of semiconductor and crystal materials

DOEpatents

Stowe, Ashley C.; Speight, Douglas

2016-11-22

A method for the additive manufacturing of inorganic crystalline materials, including: physically combining a plurality of starting materials that are used to form an inorganic crystalline compound to be used as one or more of a semiconductor, scintillator, laser crystal, and optical filter; heating or melting successive regions of the combined starting materials using a directed heat source having a predetermined energy characteristic, thereby facilitating the reaction of the combined starting materials; and allowing each region of the combined starting materials to cool in a controlled manner, such that the desired inorganic crystalline compound results. The method also includes, prior to heating or melting the successive regions of the combined starting materials using the directed heat source, heating the combined starting materials to facilitate initial reaction of the combined starting materials. The method further includes translating the combined starting materials and/or the directed heat source between successive locations. The method still further includes controlling the mechanical, electrical, photonic, and/or optical properties of the inorganic crystalline compound.

Use of municipal solid waste incineration bottom ashes in alkali-activated materials, ceramics and granular applications: A review.

PubMed

Silva, R V; de Brito, J; Lynn, C J; Dhir, R K

2017-10-01

This paper presents a literature review on the incorporation of municipal solid waste incinerated bottom ash as raw material in several markets, other than those where it is conventionally used, such as geotechnical applications and road pavement construction. The main findings of an ample selection of experimental investigations on the use of the bottom ash as precursor of alkali-activated materials, as an adsorbent material for the removal of hazardous elements from wastewater and landfill gases, as soil replacement in agricultural activities, as partial or complete substitute of raw materials for the manufacture of ceramic-based products, as landfill cover and as biogas production enhancer, were gathered, collated and analysed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Identification and Purification of Nyalo River Silica Sand as Raw Material for the Synthesis of Sodium Silicate

NASA Astrophysics Data System (ADS)

Aini, S.; Nizar, U. K.; NST, A. Amelia; Efendi, J.

2018-04-01

This research is on identification and purification of silica sand from Nyalo River. It will be used as a raw material for synthesis of sodium silicate. Silica sand was separated from clay by washing it with water, and then the existing alumina and iron oxide were removed by soaking the silica sand with 1 M HNO3 solution. Qualitative and quantitative analysis of the silica sand with X-ray diffraction and X-ray fluorescence revealed that, silica sand existed in quartz form and contained a small amount of impurity oxide such as Al2O3, K2O, MgO, CaO, Fe2O3 with percentage below the minimum threshold. The percentages of silica were 80.59% before purification. After three purificationsteps the silica percentage become 98.38%. It exceedsthe minimum threshold of silica percentage for industry.So, the silica sand from Nyalo River has high potency as a raw material for sodium silicate synthesizing.

Politics and the world's raw materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lepkowski, W.

1979-06-04

New meaning is given to problems of raw materials scarcity in the development of national policies by mineral-rich developing countries. A combination of socio-economic and political factors is shown in countries like Zaire to be shaping decisions on ore production, which directly affects the economies of industrialized countries and world trade. The developing countries need cash from their ores to finance debts, but capitalism has not produced an adequate infrastructure and has not satisfied the poor. A debate is emerging between those who want to restructure a new international economic order and those who want to use industrial wealth andmore » existing financial institutions to secure order in these countries so that mineral production continues. Critical raw materials imported by the US from developing countries are felt by some to have created a situation of vulnerability as Union Carbide and other multinational corporations have shifted processing operations to the source of the ore. Arguments are presented for both sides of the question of whether a new economic order is needed.« less

Evaluation of the lubricating effect of magnesium stearate and glyceryl behenate solid lipid nanoparticles in a direct compression process.

PubMed

Martínez-Acevedo, Lizbeth; Zambrano-Zaragoza, María de la Luz; Vidal-Romero, Gustavo; Mendoza-Elvira, Susana; Quintanar-Guerrero, David

2018-05-02

The aim of this study was to develop solid lipid nanoparticles (SLN) and introduce them into a direct compression process to evaluate their lubricant properties. The study consisted of preparing glyceryl behenate SLN (Compritol® 888 ATO) by hot dispersion, and magnesium stearate SLN by a novel nanoprecipitation/ion exchange method. The ejection force was measured for nanosystems and raw materials in a formulation typically used for direct compression. The smallest particle sizes obtained were 456 nm for Compritol® 888 ATO and 330 nm for magnesium stearate. Results show that the NPs used as lubricants in a direct compression model formulation provided efficient lubrication by maintaining the lubricating properties of the system, thereby decreasing the amount of lubricant used compared to the raw material. The lubricating effect showed an increase of 15-30% for magnesium stearate and Compritol® 888 ATO, compared to the raw material at concentrations above 2%. Copyright © 2018 Elsevier B.V. All rights reserved.

Parameters for assessing the aquatic environmental impact of cosmetic products.

PubMed

Vita, N A; Brohem, C A; Canavez, A D P M; Oliveira, C F S; Kruger, O; Lorencini, M; Carvalho, C M

2018-05-01

The cosmetic industry's growing concern about the impact of its supply chain on the environment, sustainability of raw materials, and biodiversity increases the need to ensure that the final product has a lower environmental impact. The objective of this review is to summarize and compare the information available from international organizations and legislation regarding the main criteria used to assess raw materials for aquatic toxicity, as well as the most suitable alternative methods for obtaining assessment parameters. Using the literature available in databases, a review of the scientific literature and international legislation, this work discusses and compares the parameters established by international organizations such as the Environmental Protection Agency (EPA) and Cradle to Cradle (C2C), as well as European legislation, namely, European Regulation 1272/2008, for assessing environmental impact. Defining the ecotoxicity parameters of the main classes of raw materials in rinse-off cosmetic products can enable the development of products that are more environmentally sustainable, prioritizing substances with less environmental impact. Copyright © 2018 Elsevier B.V. All rights reserved.

Freezing of meat raw materials affects tyramine and diamine accumulation in spontaneously fermented sausages.

PubMed

Bover-Cid, Sara; Miguelez-Arrizado, M Jesús; Luz Latorre Moratalla, L; Vidal Carou, M Carmen

2006-01-01

Biogenic amine accumulation was studied in spontaneously fermented sausages (Fuet) manufactured from unfrozen-fresh meat (U-sausages) and frozen-thawed meat (F-sausages). The aim was to investigate whether the frozen storage of raw materials affects the microbial composition and its aminogenic activity during sausage fermentation. Tyramine was the major amine in all sausages. Although the final levels were similar, tyramine accumulated more rapidly in F-sausages, which contained putrescine as the second amine. By contrast, U-sausages accumulated much more cadaverine than putrescine. F-sausages showed a slightly lower pH and free amino acid content as well as higher counts of technological flora (lactic acid and gram positive catalase positive bacteria) and lower counts of enterobacteria. Therefore, to freeze the meat raw materials for few days before sausage manufacture could be a useful practice, especially for the artisan fermented sausages (without starter), because it helps to reduce enterobacteria development and cadaverine production.

Influence of sugarcane bagasse variability on sugar recovery for cellulosic ethanol production.

PubMed

Andrade, Liliane Pires; Crespim, Elaine; de Oliveira, Nilton; de Campos, Rafael Carinha; Teodoro, Juliana Conceição; Galvão, Célia Maria Araújo; Maciel Filho, Rubens

2017-10-01

In the context of cellulosic ethanol production, special attention must be given to the raw material, as it affects final product yield. As observed for sugarcane, bagasse variations may derive from several elements, for instance edaphoclimatic factors, seasonality, maturation stage and harvesting techniques. Therefore, in the present work, to investigate the impact of raw material characteristics on process performance, sugarcane bagasse from four harvests from October/2010 to October/2011 was pretreated by steam explosion and had its soluble and insoluble solids contents measured, following enzymatic hydrolysis to assess glucan conversion. As confirmed by ANOVA, glucose concentration was related to the solids content in the reactor, whereas glucan conversion was related to the enzymatic load. Variations in raw material composition were indeed observed to significantly interfere in the final sugar recovery, probably due to the increase in the impurities observed as a result of the type of harvest performed in 2011. Copyright © 2017 Elsevier Ltd. All rights reserved.

Determination of Major Phenolic Compounds in Echinacea spp. Raw Materials and Finished Products by High-Performance Liquid Chromatography with Ultraviolet Detection: Single-Laboratory Validation Matrix Extension

PubMed Central

Brown, Paula N.; Chan, Michael; Paley, Lori; Betz, Joseph M.

2013-01-01

A method previously validated to determine caftaric acid, chlorogenic acid, cynarin, echinacoside, and cichoric acid in echinacea raw materials has been successfully applied to dry extract and liquid tincture products in response to North American consumer needs. Single-laboratory validation was used to assess the repeatability, accuracy, selectivity, LOD, LOQ, analyte stability (ruggedness), and linearity of the method, with emphasis on finished products. Repeatability precision for each phenolic compound was between 1.04 and 5.65% RSD, with HorRat values between 0.30 and 1.39 for raw and dry extract finished products. HorRat values for tinctures were between 0.09 and 1.10. Accuracy of the method was determined through spike recovery studies. Recovery of each compound from raw material negative control (ginseng) was between 90 and 114%, while recovery from the finished product negative control (maltodextrin and magnesium stearate) was between 97 and 103%. A study was conducted to determine if cichoric acid, a major phenolic component of Echinacea purpurea (L.) Moench and E. angustifolia DC, degrades during sample preparation (extraction) and HPLC analysis. No significant degradation was observed over an extended testing period using the validated method. PMID:22165004

Determination of major phenolic compounds in Echinacea spp. raw materials and finished products by high-performance liquid chromatography with ultraviolet detection: single-laboratory validation matrix extension.

PubMed

Brown, Paula N; Chan, Michael; Paley, Lori; Betz, Joseph M

2011-01-01

A method previously validated to determine caftaric acid, chlorogenic acid, cynarin, echinacoside, and cichoric acid in echinacea raw materials has been successfully applied to dry extract and liquid tincture products in response to North American consumer needs. Single-laboratory validation was used to assess the repeatability, accuracy, selectivity, LOD, LOQ, analyte stability (ruggedness), and linearity of the method, with emphasis on finished products. Repeatability precision for each phenolic compound was between 1.04 and 5.65% RSD, with HorRat values between 0.30 and 1.39 for raw and dry extract finished products. HorRat values for tinctures were between 0.09 and 1.10. Accuracy of the method was determined through spike recovery studies. Recovery of each compound from raw material negative control (ginseng) was between 90 and 114%, while recovery from the finished product negative control (maltodextrin and magnesium stearate) was between 97 and 103%. A study was conducted to determine if cichoric acid, a major phenolic component of Echinacea purpurea (L.) Moench and E. angustifolia DC, degrades during sample preparation (extraction) and HPLC analysis. No significant degradation was observed over an extended testing period using the validated method.

75 FR 32505 - Importer of Controlled Substances; Notice of Registration

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-08

... 55858), Johnson Matthey, Inc., Pharmaceutical Materials, 2003 Nolte Drive, West Deptford, New Jersey... Phenylacetone (8501) II Coca Leaves (9040) II Thebaine (9333) II Opium, raw (9600) II Noroxymorphone (9668) II Poppy Straw Concentrate (9670) II The company plans to import the listed controlled substances as raw...

Process for removing polymer-forming impurities from naphtha fraction

DOEpatents

Kowalczyk, D.C.; Bricklemyer, B.A.; Svoboda, J.J.

1983-12-27

Polymer precursor materials are vaporized without polymerization or are removed from a raw naphtha fraction by passing the raw naphtha to a vaporization zone and vaporizing the naphtha in the presence of a wash oil while stripping with hot hydrogen to prevent polymer deposits in the equipment. 2 figs.

Process for removing polymer-forming impurities from naphtha fraction

DOEpatents

Kowalczyk, Dennis C.; Bricklemyer, Bruce A.; Svoboda, Joseph J.

1983-01-01

Polymer precursor materials are vaporized without polymerization or are removed from a raw naphtha fraction by passing the raw naphtha to a vaporization zone (24) and vaporizing the naphtha in the presence of a wash oil while stripping with hot hydrogen to prevent polymer deposits in the equipment.

Energy-Efficient and Low-GHG-Emission "Thiometallurgy"

NASA Astrophysics Data System (ADS)

Neelameggham, Neale R.; Brown, Robert E.; Davis, Brian R.

2014-09-01

Extractive metallurgy has used free or combined sulfur as both the raw material and the energy material in carrying out economical manufacture of several metals in millions of tons per year quantities over the past century. This has controlled carbon emissions in an unintentional fashion and out of necessity as the ores in many cases have been sulfides to start with. And the benefits of heat generation by the sulfides reacting with oxygen in the process steps have avoided the use of carbon as a fuel in providing the reaction temperatures. In this article, we will show the inherent benefits of "thiometallurgy," which uses sulfur in the extraction of metals in alleviating CO2 and water vapor-greenhouse gas (GHG) emissions, as well as its ability to provide a cost-effective energy material solution. Such solutions are not only applicable to existing base metal production but, as the authors will show, also are applicable to newer processes in the production of other metals and chemicals, such as alkaline earth metals, titanium, and to an extent aluminum in an indirect fashion. Iron ores can also be treated with thiometallurgy to meet the ULCOS criterion of ultra-low carbon dioxide steel being studied in Europe. The concept of generating "thiopower" as an alternative energy approach is also introduced by the authors.

High-purity silicon for solar cell applications

NASA Technical Reports Server (NTRS)

Dosaj, V. D.; Hunt, L. P.; Schei, A.

1978-01-01

The article discusses the production of solar cells from high-purity silicon. The process consists of reducing the level of impurities in the raw materials, preventing material contamination before and after entering the furnace, and performing orders-of-magnitude reduction of metal impurity concentrations. The high-purity raw materials are considered with reference to carbon reductants, silica, and graphite electrodes. Attention is also given to smelting experiments used to demonstrate, in an experimental-scale furnace, the production of high-purity SoG-Si. It is found that high-purity silicon may be produced from high-purity quartz and chemically purified charcoal in a 50-kVA arc furnace. The major contamination source is shown to be impurities from the carbon reducing materials.

Fermentanomics: Relating quality attributes of a monoclonal antibody to cell culture process variables and raw materials using multivariate data analysis.

PubMed

Rathore, Anurag S; Kumar Singh, Sumit; Pathak, Mili; Read, Erik K; Brorson, Kurt A; Agarabi, Cyrus D; Khan, Mansoor

2015-01-01

Fermentanomics is an emerging field of research and involves understanding the underlying controlled process variables and their effect on process yield and product quality. Although major advancements have occurred in process analytics over the past two decades, accurate real-time measurement of significant quality attributes for a biotech product during production culture is still not feasible. Researchers have used an amalgam of process models and analytical measurements for monitoring and process control during production. This article focuses on using multivariate data analysis as a tool for monitoring the internal bioreactor dynamics, the metabolic state of the cell, and interactions among them during culture. Quality attributes of the monoclonal antibody product that were monitored include glycosylation profile of the final product along with process attributes, such as viable cell density and level of antibody expression. These were related to process variables, raw materials components of the chemically defined hybridoma media, concentration of metabolites formed during the course of the culture, aeration-related parameters, and supplemented raw materials such as glucose, methionine, threonine, tryptophan, and tyrosine. This article demonstrates the utility of multivariate data analysis for correlating the product quality attributes (especially glycosylation) to process variables and raw materials (especially amino acid supplements in cell culture media). The proposed approach can be applied for process optimization to increase product expression, improve consistency of product quality, and target the desired quality attribute profile. © 2015 American Institute of Chemical Engineers.

Antimicrobial and Antiradical Activity of Extracts Obtained from Leaves of Five Species of the Genus Bergenia: Identification of Antimicrobial Compounds.

PubMed

Żbikowska, Beata; Franiczek, Roman; Sowa, Alina; Połukord, Grażyna; Krzyżanowska, Barbara; Sroka, Zbigniew

2017-09-01

An important focus of modern medicine is the search for new substances and strategies to combat infectious diseases, which present an increasing threat due to the growth of bacterial resistance to antibiotics. Another problem concerns free radicals, which in excess can cause several serious diseases. An alternative to chemical synthesis of antimicrobial and antiradical compounds is to find active substances in plant raw materials. We prepared extracts from leaves of five species of the genus Bergenia: B. purpurascens, B. cordifolia, B. ligulata, B. crassifolia, and B. ciliata. Antimicrobial and antiradical features of extracts and raw materials were assessed, and the quantities of phenolic compounds were determined. We also evaluated, using high-performance liquid chromatography, the amounts of arbutin and hydroquinone, compounds related to antimicrobial activity of these raw materials. The strongest antiradical properties were shown by leaves of B. crassifolia and B. cordifolia, the lowest by leaves of B. ciliata. The antiradical activity of extracts showed a strong positive correlation with the amount of phenols. All raw materials have significant antimicrobial properties. Among them, the ethyl acetate extracts were the most active. Antimicrobial activity very weakly correlated with the amount of arbutin, but correlated very strongly with the contents of both hydroquinone and phenolic compounds. Additional experiments using artificially prepared mixtures of phenolic compounds and hydroquinone allowed us to conclude that the most active antimicrobial substance is hydroquinone.

Optimization of substrate preparation for oyster mushroom (Pleurotus ostreatus) cultivation by studying different raw materials and substrate preparation conditions (composting: phases I and II).

PubMed

Vieira, Fabrício Rocha; de Andrade, Meire Cristina Nogueira

2016-11-01

In recent years, oyster mushroom (Pleurotus ostreatus) has become one of the most cultivated mushrooms in the world, mainly in Brazil. Among many factors involved in a mushroom production, substrate preparation is the most critical step, which can be influenced by composting management techniques. Looking forward to optimizing the substrate preparation process, were tested different composting conditions (7 and 14 days of composting with or without conditioning), potential raw materials (decumbens grass, brizantha grass and sugarcane straw) and nitrogen supplementation (with or without wheat bran) on oyster mushroom yield and biological efficiency (BE). The substrate composted for 7 days with conditioning showed higher yield and biological efficiency of mushroom (24.04 and 100.54 %, respectively). Substrates without conditioning (7 and 14 days of composting) showed smaller mushroom yield and biological efficiency. Among the raw materials tested, brizantha grass showed higher mushroom yield followed by decumbens grass, sugarcane straw and wheat straw (28.5, 24.32, 23.5 and 19.27 %, respectively). Brizantha grass also showed higher biological efficiency followed by sugarcane straw, decumbens grass and wheat straw (123.95, 103.70, 96.90 and 86.44 %, respectively). Supplementation with wheat bran improved yield and biological efficiency in all substrate formulations tested; thus, oyster mushroom yield and biological efficiency were influenced by substrate formulation (raw materials), supplementation and composting conditions.

Designing Business System Model using System Modeling Approach to the Small and Medium Enterprises (SME) of Furniture in Indonesia

NASA Astrophysics Data System (ADS)

Sukendar, Irwan; Fatmawati, Wiwiek; Much Ibnu Subroto, Imam; Arigama, Rizki

2017-04-01

This paper studies the design of business system model with System Modeling Approach on small and medium enterprises (SMEs) of furniture. Methods used consists of five phases: phase of identification of business processes actual on SMEs of Furniture, phase of identification of deficiencies and improvement of business processes, phase of design algorithm and flowchart business processes, phase of analysis of the elements of the system, and phase of the design of data flow diagram (DFD), The results of the analysis of the elements of the system are: Products and quantities ordered product consumers and DP paid by consumers identified as elements of system inputs 1,2 and 3. The result of the calculation, payment slips and mail order (SO) are identified as elements of system output 1, 2 and 3. Acceptance of orders, stocks checking of raw materials at the warehouse, calculating raw material requirements, adequacy of raw materials, the price of the contract, and the due date, as well as the submission of the results of calculations to consumers were identified as elements of system components 1, 2, 3, and 4. Admin taking orders, Admin check stocks of raw materials at the warehouse, Admin making calculation, and Admin convey the results of calculations to consumers were identified as an element of interaction system 1, 2, 3, and 4. Consumers were identified as element of environmental systems. Moreover, the boundary between SMEs and consumers were identified as elements of the system boundary.

Soanian lithic occurrences and raw material exploitation in the Siwalik Frontal Zone, northern India: a geoarchaeological perspective.

PubMed

Chauhan, Parth R

2008-05-01

In the Himalayan foothills of northern India, evidence of widespread hominin occupation since at least the late Middle Pleistocene has been known since the early 20th century and indicates varied patterns of land-use and intraregional mobility. This lithic evidence primarily belongs to the Soanian industry, representing some of the highest concentrations of Paleolithic assemblages in the Old World based exclusively on pebble and cobble clasts. This body of evidence also signifies interregional dispersal from peninsular India or northern Pakistan, leading to environmental preferences that spread quickly through hominin populations in the region within a relatively short timespan. While rich in its technological repertoire, the Soanian industry is poorly- understood regarding site selection and raw material exploitation over time. Recent efforts demonstrate that Soanian sites on Siwalik frontal slopes between two major rivers vary considerably in their artifact quantities regardless of abundant raw material sources found across the landscape. Most of the assemblages suggest raw material transport distances of three kilometers or less from the localized sources. Geoarchaeological investigations at the richest known Soanian site, Toka, reveal dynamic evidence of pre- and postdepositional site formation including the exploitation of quartzite pebbles and cobbles by Pleistocene hominins from terrace and streambed contexts within a 1 km2 radius. Some field observations also disprove claims made by previous workers, of artifacts eroding out of late Pliocene exposures of the Upper Siwalik Tatrot Formation around Toka.

[Simultaneous separation and detection of principal component isomer and related substances of raw material drug of ammonium glycyrrhizinate by RP-HPLC and structure confirmation].

PubMed

Zhao, Yan-Yan; Liu, Li-Yan; Han, Yuan-Yuan; Li, Yue-Qiu; Wang, Yan; Shi, Min-Jian

2013-08-01

A simple, fast and sensitive analytical method for the simultaneous separation and detection of 18alpha-glycyrrhizinic acid, 18beta-glycyrrhizinic acid, related substance A and related substance B by RP-HPLC and drug quality standard was established. The structures of principal component isomer and related substances of raw material drug of ammonium glycyrrhizinate have been confirmed. Reference European Pharmacopoeia EP7.0 version, British Pharmacopoeia 2012 version, National Drug Standards of China (WS 1-XG-2002), domestic and international interrelated literature were referred to select the composition of mobile phase. The experimental parameters including salt concentration, pH, addition quantities of organic solvent, column temperature and flow rate were optimized. Finally, the assay was conducted on a Durashell-C18 column (250 mm x 4.6 mm, 5 microm) with 0.01 mol x mL(-1) ammonium perchlorate (add ammonia to adjust the pH value to 8.2) -methanol (48 : 52) as mobile phase at the flow rate of 0.8 mL x min(-1), and the detection wavelength was set at 254 nm. The column temperature was 50 degrees C and the injection volume was 10 microL. The MS, NMR, UV and RP-HPLC were used to confirm the structures of principal component isomer and related substances of raw material drug of ammonium glycyrrhizinate. Under the optimized separation conditions, the calibration curves of 18 alpha-glycyrrhizinic acid, 18beta-glycyrrhizinic acid, related substance A and related substance B showed good linearity within the concentration of 0.50-100 microg x mL(-1) (r = 0.999 9). The detection limits for 18alpha-glycyrrhizinic acid, 18beta-glycyrrhizinic acid, related substance A and related substance B were 0.15, 0.10, 0.10, 0.15 microg x mL(-1) respectively. The method is sensitive, reproducible and the results are accurate and reliable. It can be used for chiral resolution of 18alpha-glycyrrhizinic acid, 18Pbeta-glycyrrhizinic acid, and detection content of principal component and related substances of raw material drug of ammonium glycyrrhizinate. It is concluded that the separation of principal component isomer of raw material drug of ammonium glycyrrhizinate and the validity of the substance's structure assignments of retention time being 1.2 in the European pharmacopoeia EP7.0 version, British pharmacopoeia 2012 version remains open to question. It may be of practical value for the quality control of raw material drug, preparation, and Chinese herbal medicine of ammonium glycyrrhizinate.

Adaptation of Methanogenic Inocula to Anaerobic Digestion of Maize Silage

PubMed Central

Wojcieszak, Martyna; Pyzik, Adam; Poszytek, Krzysztof; Krawczyk, Pawel S.; Sobczak, Adam; Lipinski, Leszek; Roubinek, Otton; Palige, Jacek; Sklodowska, Aleksandra; Drewniak, Lukasz

2017-01-01

A well-balanced microbial consortium is crucial for efficient biogas production. In turn, one of a major factor that influence on the structure of anaerobic digestion (AD) consortium is a source of microorganisms which are used as an inoculum. This study evaluated the influence of inoculum sources (with various origin) on adaptation of a biogas community and the efficiency of the biomethanization of maize silage. As initial inocula for AD of maize silage the samples from: (i) an agricultural biogas plant (ABP) which utilizes maize silage as a main substrate, (ii) cattle slurry (CS), which contain elevated levels of lignocelluloses materials, and (iii) raw sewage sludge (RSS) with low content of plant origin materials were used. The adaptation of methanogenic consortia was monitored during a series of passages, and the functionality of the adapted consortia was verified through start-up operation of AD in two-stage reactors. During the first stages of the adaptation phase, methanogenic consortia occurred very slowly, and only after several passages did the microbial community adapts to allow production of biogas with high methane content. The ABP consortium revealed highest biogas production in the adaptation and in the start-up process. The biodiversity dynamics monitored during adaptation and start-up process showed that community profile changed in a similar direction in three studied consortia. Native communities were very distinct to each other, while at the end of the Phase II of the start-up process microbial diversity profile was similar in all consortia. All adopted bacterial communities were dominated by representatives of Porphyromonadaceae, Rikenellaceae, Ruminococcaceae, and Synergistaceae. A shift from low acetate-preferring acetoclastic Methanosaetaceae (ABP and RSS) and/or hydrogenotrophic Archaea, e.g., Methanomicrobiaceae (CS) prevailing in the inoculum samples to larger populations of high acetate-preferring acetoclastic Methanosarcinaceae was observed by the end of the experiment. As a result, three independent, functional communities that syntrophically produced methane from acetate (primarily) and H2/CO2, methanol and methylamines were adapted. This study provides new insights into the specific process by which different inocula sampled from typical methanogenic environments that are commonly used to initiate industrial installations gradually adapted to allow biogas production from maize silage. PMID:29033919

[Effect of qinghuobaiduyin on the expression of high mobility group box chromosomal protein 1 in macrophage].

PubMed

Li, Ping; Xu, Dan; Luo, Chengqun

2010-07-01

To observe the expression of high mobility group box chromosomal protein 1(HMGB1) in RAW264.7 macrophages after interfering with burning serum and qinghuobaidu-yin (QHBDY), and to find out the endogenous protection mechanism of QHBDY resisting inflammation reaction. RT-PCR was used to detect the expression of HMGB1 in RAW264.7 macrophages after interfering RAW264.7 macrophages with normal SD rat serum, burning SD rat serum, and QHBDY feeding SD rat serum. Small quantity of HMGB1 mRNA was expressed in RAW264.7. The expression of HMGB1 mRNA fluctuated around the standard level after interfering with normal serum of SD rats. The expression of HMGB1 mRNA rose at 3 h, and then decreased to the standard level; at 18 h, it rose rapidly; at 36 h, it reached the peak; and at 48 h, it remained at the high level after interfering with burning serum. The expression of HMGB1 mRNA increased at 3 h, and then decreased to the standard level. At 24 h, it started to rise after interfering with herb serum, and was lower than that of; the burning serum group (P<0.05). Burning serum can increase the expression of HMGB1 mRNA in RAW264.7. QHBDY can decrease the high expression of HMGB1 mRNA in RAW264.7 caused by burning serum.

Longitudinal study on the sources of Listeria monocytogenes contamination in cold-smoked salmon and its processing environment in Italy.

PubMed

Di Ciccio, Pierluigi; Meloni, Domenico; Festino, Anna Rita; Conter, Mauro; Zanardi, Emanuela; Ghidini, Sergio; Vergara, Alberto; Mazzette, Rina; Ianieri, Adriana

2012-08-01

The aim of the present study was to investigate the sources of Listeria monocytogenes contamination in a cold smoked salmon processing environment over a period of six years (2003-2008). A total of 170 samples of raw material, semi-processed, final product and processing surfaces at different production stages were tested for the presence of L. monocytogenes. The L. monocytogenes isolates were characterized by multiplex PCR for the analysis of virulence factors and for serogrouping. The routes of contamination over the six year period were traced by PFGE. L. monocytogenes was isolated from 24% of the raw salmon samples, 14% of the semi-processed products and 12% of the final products. Among the environmental samples, 16% were positive for L. monocytogenes. Serotyping yielded three serovars: 1/2a, 1/2b, 4b, with the majority belonging to serovars 1/2a (46%) and 1/2b (39%). PFGE yielded 14 profiles: two of them were repeatedly isolated in 2005-2006 and in 2007-2008 mainly from the processing environment and final products but also from raw materials. The results of this longitudinal study highlighted that contamination of smoked salmon occurs mainly during processing rather than originating from raw materials, even if raw fish can be a contamination source of the working environment. Molecular subtyping is critical for the identification of the contamination routes of L. monocytogenes and its niches into the production plant when control strategies must be implemented with the aim to reduce its prevalence during manufacturing. Copyright © 2012 Elsevier B.V. All rights reserved.

FennoFlakes: a project for identifying flake graphite ores in the Fennoscandian shield and utilizing graphite in different applications

NASA Astrophysics Data System (ADS)

Palosaari, Jenny; Eklund, O.; Raunio, S.; Lindfors, T.; Latonen, R.-M.; Peltonen, J.; Smått, J.-H.; Kauppila, J.; Lund, S.; Sjöberg-Eerola, P.; Blomqvist, R.; Marmo, J.

2016-04-01

Natural graphite is a strategic mineral, since the European Commission stated (Report on critical raw materials for the EU (2014)) that graphite is one of the 20 most critical materials for the European Union. The EU consumed 13% of all flake graphite in the world but produced only 3%, which stresses the demand of the material. Flake graphite, which is a flaky version of graphite, forms under high metamorphic conditions. Flake graphite is important in different applications like batteries, carbon brushes, heat sinks etc. Graphene (a single layer of graphite) can be produced from graphite and is commonly used in many nanotechnological applications, e.g. in electronics and sensors. The steps to obtain pure graphene from graphite ore include fragmentation, flotation and exfoliation, which can be cumbersome and resulting in damaging the graphene layers. We have started a project named FennoFlakes, which is a co-operation between geologists and chemists to fill the whole value chain from graphite to graphene: 1. Exploration of graphite ores (geological and geophysical methods). 2. Petrological and geochemical analyses on the ores. 3. Development of fragmentation methods for graphite ores. 4. Chemical exfoliation of the enriched flake graphite to separate flake graphite into single and multilayer graphene. 5. Test the quality of the produced material in several high-end applications with totally environmental friendly and disposable material combinations. Preliminary results show that flake graphite in high metamorphic areas has better qualities compared to synthetic graphite produced in laboratories.

Wind energy in the United States and materials required for the land-based wind turbine industry from 2010 through 2030

USGS Publications Warehouse

Wilburn, David R.

2011-01-01

The generation of electricity in the United States from wind-powered turbines is increasing. An understanding of the sources and abundance of raw materials required by the wind turbine industry and the many uses for these materials is necessary to assess the effect of this industry's growth on future demand for selected raw materials relative to the historical demand for these materials. The U.S. Geological Survey developed estimates of future requirements for raw (and some recycled) materials based on the assumption that wind energy will supply 20 percent of the electricity consumed in the United States by 2030. Economic, environmental, political, and technological considerations and trends reported for 2009 were used as a baseline. Estimates for the quantity of materials in typical "current generation" and "next generation" wind turbines were developed. In addition, estimates for the annual and total material requirements were developed based on the growth necessary for wind energy when converted in a wind powerplant to generate 20 percent of the U.S. supply of electricity by 2030. The results of the study suggest that achieving the market goal of 20 percent by 2030 would require an average annual consumption of about 6.8 million metric tons of concrete, 1.5 million metric tons of steel, 310,000 metric tons of cast iron, 40,000 metric tons of copper, and 380 metric tons of the rare-earth element neodymium. With the exception of neodymium, these material requirements represent less than 3 percent of the U.S. apparent consumption for 2008. Recycled material could supply about 3 percent of the total steel required for wind turbine production from 2010 through 2030, 4 percent of the aluminum required, and 3 percent of the copper required. The data suggest that, with the possible exception of rare-earth elements, there should not be a shortage of the principal materials required for electricity generation from wind energy. There may, however, be selective manufacturing shortages if the total demand for raw materials from all markets is greater than the available supply of these materials or the capacity of industry to manufacture components. Changing economic conditions could also affect the development schedule of anticipated capacity.

Life cycle assessment of Mexican polymer and high-durability cotton paper banknotes.

PubMed

Luján-Ornelas, Cristina; Mancebo Del C Sternenfels, Uriel; Güereca, Leonor Patricia

2018-07-15

This study compares the environmental performance of Mexican banknotes printed on high-durability cotton paper (HD paper) and thermoplastic polymer (polymer) through a life cycle assessment to appraise the environmental impacts from the extraction of raw materials to the final disposal of the banknotes. The functional unit was defined considering the next parameters: 1) lifespan of the banknotes, stablished in 31.5 and 54months for HD paper and polymer, respectively; 2) denomination, selecting $200 pesos banknotes; 3) a 5year time frame and 4) a defined amount of money, in this case stablished as the monthly cash supply of an average Mexican household, equaling $12,708 pesos. Accordingly, 121 pieces for the HD paper and 71 pieces for the polymer banknotes were analyzed. The results favor the banknotes printed on polymer substrate primarily because of the longer lifespan of this type of material; however, there is a considerable environmental impact in the stages of distribution, followed by the extraction of the raw materials (crude oil) during manufacturing. Regarding the HD cotton paper, the major impact corresponds to extraction of the raw materials, followed by the distribution of the banknotes. The inclusion of the automatic teller machines (ATMs) in the life cycle assessment of banknotes shows that the electricity required by these devices became the largest contributor to the environmental impacts. Additionally, the sensitivity analysis that the average lifetime of the banknotes is a determining factor for the environmental impacts associated with the whole life cycle of this product. The life cycle stages that refer to the extraction of the raw materials, combined with the average lifetime of the banknotes and the electricity required during the usage stage, are determining factors in the total environmental impact associated with Mexican banknotes. Copyright © 2018 Elsevier B.V. All rights reserved.

Physicochemical characterization of raw materials and co-products from the titanium dioxide industry.

PubMed

Gázquez, M J; Bolívar, J P; García-Tenorio, R; Vaca, F

2009-07-30

The present study was conducted to characterize several raw materials and co-products from the titanium dioxide industry in relation to their elemental composition (major, minor and trace elements), granulometry, mineralogy, microscopic morphology and physical composition. The main objective was to gain basic information for the future potential application of these co-products in fields such as agriculture, construction, civil engineering, etc. Microscopic studies were performed by applying scanning electron microscopy with X-ray microanalysis (SEM-XRMA) while the mineralogical compositions were analysed by means of the X-ray diffraction (XRD) technique. The concentrations of major elements such as Na, Al, Si, Ca, Ti, Fe, S and K were determined by X-ray fluorescence (XRF), while heavy metals and other trace elements were determined by ICP-MS. The physicochemical characterization of the raw materials used in the titanium dioxide industry, in addition to the characterization of the co-products generated, has enabled the evaluation of the degree of fractionation of different elements and compounds between the different co-products, as well as the control of the possible variations in the physicochemical composition of the raw materials throughout the time and the study of the influence of these variations in the characteristics of the obtained co-products. As a main conclusion of our study, it is possible to indicate that the levels of the pollutant elements associated to the co-products analysed were, in general, within safe limits and, therefore, they could potentially be used in composites as fertilizers or for building materials in road construction, etc. Nevertheless, for the specific application of each of these co-products in agriculture, construction and civil engineering, additional studies need to be performed to evaluate their appropriateness for the proposed application, together with specific studies on their health and environmental impact.

Contents of vitamin C, carotenoids, tocopherols, and tocotrienols in the subtropical plant species Cyphostemma digitatum as affected by processing.

PubMed

Al-Duais, Mohammed; Hohbein, Juliane; Werner, Susanne; Böhm, Volker; Jetschke, Gottfried

2009-06-24

The subtropical plant species Cyphostemma digitatum, Vitaceae, is used in central Yemen in traditional medicine, as a culinary herb, and as a source of food flavoring. The contents of vitamin C, vitamin E, and carotenoids and changes caused by common processing were investigated. Carotenoids were determined by reversed phase C30-high-performance liquid chromatography (HPLC) with diode array detection at 470 nm, while tocopherols and tocotrienols were analyzed by using normal phase HPLC with fluorescence detection (excitation, 292 nm; emission, 330 nm). Ascorbic acid was determined spectrophotometrically after reaction with DNP by measuring the absorbance at 520 nm. For the raw material and for the processed commercial food product, both in dried form, reasonable quantities of carotenoids were found in the raw material as follows: lutein, 18.89 +/- 0.73 mg/100 g; zeaxanthin, 9.46 +/- 0.30 mg/100 g; canthaxanthin, 0.21 +/- 0.01 mg/100 g; beta-cryptoxanthin, 0.67 +/- 0.03 mg/100 g; and beta-carotene, 14.60 +/- 0.46 mg/100 g. Household processing reduced the carotenoid contents dramatically; only beta-carotene sustained the processing. Likewise, vitamin C, 49.50 +/- 0.01 mg/100 g in the raw material and 20.30 +/- 0.02 mg/100 g in the processed material, was affected negatively by processing; only 41% was retained after processing. In contrast, the outstanding high content of vitamin E, 82.74 +/- 0.63 mg/100 g in the raw material, was increased by processing to 101.20 +/- 1.38 mg/100 g; it was found in different forms, some of which were rare in other sources.

Characterization of some selected vulcanized and raw silicon rubber materials

NASA Astrophysics Data System (ADS)

Sasikala, A.; Kala, A.

2017-06-01

Silicone Rubber is a high need of importance of Medical devices, Implants, Aviation and Aerospace wiring applications. Silicone rubbers are widely used in industry, and there are in multiple formulations. A raw and vulcanized silicone rubber Chemical and Physical structures of particles was confirmed and mechanical strength has been analyzed by FTIR spectroscopy. Thermal properties studied from Thermo Gravimetric Analysis (TGA) and Differential Scanning Calorimetry (DSC) analysis. Activation energy of the rubber materials were calculated using Broido method, Piloyon-Novikova relation and coats-Red fern methods.

Analysis of the cement clinker produced with incorporation of petroleum sludge

NASA Astrophysics Data System (ADS)

Benlamoudi, A.; Kadir, A. Abdul; Khodja, M.; Nuruddin, M. F.

2018-04-01

Very limited researches have been conducted on the incorporation of petroleum sludge waste into cement clinker production even though this waste may contain similar components to those of clinker raw materials. In this research, petroleum sludge was integrated into cement plant as raw material to produce the cement clinker. As results, incorporation of 5% of this waste was able to produce an acceptable quality of cement. Despite the use of petroleum sludge has decreased the properties of the produced clinker, but it still fit the requirements.

Gas fluidized-bed stirred media mill

DOEpatents

Sadler, III, Leon Y.

1997-01-01

A gas fluidized-bed stirred media mill is provided for comminuting solid ticles. The mill includes a housing enclosing a porous fluidizing gas diffuser plate, a baffled rotor and stator, a hollow drive shaft with lateral vents, and baffled gas exhaust exit ports. In operation, fluidizing gas is forced through the mill, fluidizing the raw material and milling media. The rotating rotor, stator and milling media comminute the raw material to be ground. Small entrained particles may be carried from the mill by the gas through the exit ports when the particles reach a very fine size.

RECOVERY OF URANIUM VALUES FROM URANIUM BEARING RAW MATERIALS

DOEpatents

Michal, E.J.; Porter, R.R.

1959-06-16

Uranium leaching from ground uranium-bearing raw materials using MnO/sub 2/ in H/sub 2/SO/sub 4/ is described. The MnO/sub 2/ oxidizes U to the leachable hexavalent state. The MnO/sub 2/ does not replace Fe normally added, because the Fe complexes P and catalyzes the MnO/sub 2/ reaction. Three examples of continuous processes are given, but batch operation is also possible. The use of MnO/sub 2/ makes possible recovery of very low U values. (T.R.H.)

6. Photocopied August 1978. LINEUP OF HORRY ROTARY FURNACES ON ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. Photocopied August 1978. LINE-UP OF HORRY ROTARY FURNACES ON THE SECOND FLOOR OF THE MICHIGAN LAKE SUPERIOR POWER COMPANY POWER HOUSE. THE HOPPERS WHICH FED THE RAW MATERIALS INTO THE FURNACES ARE SHOWN ABOVE THE FURNACES. AS THE 'SPOOL' OF THE FURNACE ROTATED PAST THE ELECTRODES PLATES WERE ADDED TO HOLD THE FINISHED PRODUCT AND THE DESCENDING RAW MATERIALS IN PLACE. THE DIRECTION OF ROTATION OF THE FURNACES SHOWN IN THIS PHOTO IS CLOCKWISE, (M). - Michigan Lake Superior Power Company, Portage Street, Sault Ste. Marie, Chippewa County, MI

Method of producing .beta.-spodumene bodies

DOEpatents

Chyung, Kenneth; Day, J. Paul; Holleran, Louis M.; Olszewski, Anthony R.

1999-01-01

Beta-spodumene bodies and method of preparing the bodies that involves providing a uniform plastic batch of inorganic raw materials, organic binder, and vehicle, wherein the inorganic raw materials are composed of, in percent by weight, about 75% to 95% minerals, and about 5% to 25% glass. The batch is formed into a green body that is fired to produce a body composed substantially of beta-spodumene, and having a thermal expansion coefficient of <10.times.10.sup.-7 /.degree.C.(0-800.degree. C.), and a strength of .gtoreq.4 Ksi.

Defense Horizons. No. 73. September 2012. Toward the Printed World: Additive Manufacturing and Implications for National Security

DTIC Science & Technology

2012-09-01

allowing it to dry or baking it in a kiln . A modern factory would take a block of raw material and then use machinery to pare away un- necessary... conventional “subtractive manu- facturing”—taking a block of raw material and removing excess until the finished product remains—the process as a whole...is more efficient and less wasteful. Another major benefit of AM is the fact that com- plexity is “free.” In conventional manufacturing, increasing

Petro-mineralogy and geochemistry as tools of provenance analysis on archaeological pottery: Study of Inka Period ceramics from Paria, Bolivia

NASA Astrophysics Data System (ADS)

Szilágyi, V.; Gyarmati, J.; Tóth, M.; Taubald, H.; Balla, M.; Kasztovszky, Zs.; Szakmány, Gy.

2012-07-01

This paper summarized the results of comprehensive petro-mineralogical and geochemical (archeometrical) investigation of Inka Period ceramics excavated from Inka (A.D. 1438-1535) and Late Intermediate Period (A.D. 1000/1200-1438) sites of the Paria Basin (Dept. Oruro, Bolivia). Applying geological analytical techniques we observed a complex and important archaeological subject of the region and the era, the cultural-economic influence of the conquering Inkas in the provincial region of Paria appearing in the ceramic material. According to our results, continuity and changes of raw material utilization and pottery manufacturing techniques from the Late Intermediate to the Inka Period are characterized by analytical methods. The geological field survey provided efficient basis for the identification of utilized raw material sources. On the one hand, ceramic supply of both eras proved to be based almost entirely on local and near raw material sources. So, imperial handicraft applied local materials but with sophisticated imperial techniques in Paria. On the other hand, Inka Imperial and local-style vessels also show clear differences in their material which suggests that sources and techniques functioned already in the Late Intermediate Period subsisted even after the Inka conquest of the Paria Basin. Based on our geological investigations, pottery supply system of the Paria region proved to be rather complex during the Inka Period.

The Behavioural Approach in Schools: A Time for Caution Revisited

ERIC Educational Resources Information Center

Harrop, Alex; Swinson, Jeremy

2007-01-01

This paper takes as its starting point an examination of the current status of some of the concerns that were raised in the mid-1980s about methodological problems faced by educational researchers using the behavioural approach in schools. These concerns included the measurement of agreement between observers, the interpretation of raw data…

Determination of ultraviolet filter activity on coconut oil cosmetic cream

NASA Astrophysics Data System (ADS)

Widiyati, Eni

2017-08-01

A research on determination of ultraviolet (UV) filter activity of cosmetic cream with coconut oil as raw material has been done. The cream was made by mixing the oil phase (coconut oil, stearic acid, lanolin and cetyl alcohol) at 70°C and the water phase (glycerin, aquadest and triethanolamine) at 70°C, while stirring until reached a temperature of 35°C. It was made also a cream with inorganic sunscreen TiO2 and organic sunscreen benzophenone-3 as a comparison. To study the UV filter activity, each cream was determined the UV absorption using UV spectrophotometer. The results show that cosmetic cream with coconut oil as raw material absorbs UV rays in the region of UV-C, whereas the cream with TiO2 absorbs the UV rays from UV-C to UV-A and cream with benzophenone-3 absorbs the UV rays from UV-B to UV-A region. This means that, the cosmetic cream with coconut oil as raw material has an activity as UV-C filter. If this cream is expected to have an activity as a sunscreen, it must be added an inorganic or organic sunscreen or a mixture of both as an active materials.

Investigation of Interrelation between Deformation, Composition and Structural Characteristics of Magnesium Oxychloride Cements

NASA Astrophysics Data System (ADS)

Averina, G. F.; Chernykh, T. N.; Kramar, L. Ya

2017-11-01

The paper studies the process of volume deformation changes in magnesium cement at its hardening in accordance with its composition and structural peculiarities, which result from the roasting parameters of the raw materials. The study has been carried out with the aim of broadening raw materials sources for production of magnesia cements and construction materials through the use waste products of ore-dressing and processing enterprises. The mineralogical and phase composition of magnesium cements, obtained on the basis of magnesite with high content of impurity minerals from the mine dumps, has been studied by the X-ray phase analysis and derivatography. The roasting of the initial raw materials was carried out at various temperature conditions in order to get cements of different activities. The typical content of hydrated phases has been found for the hardened magnesian stone obtained from cements with different activity degrees. The characteristics of volume deformations developed in the magnesian stone have been described in relation to its phase composition. The influence of low- and high-activity crystals and calcium oxide crystals on the soundness and the structural integrity of magnesian stone has been covered.

Researchers propose single grade rule for evaluating hardwood pallet cants

Treesearch

Hal Mitchell; Marshall White; Philip Araman; Peter Hamner

2008-01-01

In "price taker" markets, successful businesses are the low cost producers, and pallet manufacturers are no exception. The single largest cost component of pallet manufacturing is raw material costs. Cants and lumber typically account for over 60% of operating costs. In the last three decades, cants have replaced lumber as the primary raw...

77 FR 43862 - Importer of Controlled Substances; Notice of Registration; Noramco, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-26

... basic classes of controlled substances: Drug Schedule Phenylacetone (8501) II Opium, raw (9600) II Poppy... a controlled substance. Comments and requests for hearings on applications to import narcotic raw material are not appropriate. 72 FR 3417 (2007). DEA has considered the factors in 21 U.S.C. 823(a) and 952...

76 FR 35241 - Importer of Controlled Substances; Notice of Application

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-16

...-Piperidine (8333).. II Phenylacetone (8501) II Raw Opium (9600) II Concentrate of Poppy Straw (9670) II The... Technologies, 72 FR 3417 (2007), comments and requests for hearings on applications to import narcotic raw material are not appropriate. Any bulk manufacturer who is presently, or is applying to be, registered with...

PRELIMINARY COMPARATIVE STUDY OF METHODS TO EXTRACT VIRUS FROM RAW AND PROCESSED SEWAGE SLUDGES

EPA Science Inventory

Two simple virus extraction techniques were compared to an EPA standard method for detection of human enteric viruses in raw sewage sludge and class A biosolids. The techniques were used to detect both indigenous and seeded virus from a plant that distributes class A material pr...

A review on the challenges for increassed production of castor

USDA-ARS?s Scientific Manuscript database

The oil produced by castor (Ricinus communis) is an important raw material for chemical industry for its unique properties such as the only commercial source of a hydroxilated fatty acid that composes around 90% of the oil. This crop has a remarkable potential for increasing importance as a raw mate...

Optimization of Parameters for Manufacture Nanopowder Bioceramics at Machine Pulverisette 6 by Taguchi and ANOVA Method

NASA Astrophysics Data System (ADS)

Van Hoten, Hendri; Gunawarman; Mulyadi, Ismet Hari; Kurniawan Mainil, Afdhal; Putra, Bismantoloa dan

2018-02-01

This research is about manufacture nanopowder Bioceramics from local materials used Ball Milling for biomedical applications. Source materials for the manufacture of medicines are plants, animal tissues, microbial structures and engineering biomaterial. The form of raw material medicines is a powder before mixed. In the case of medicines, research is to find sources of biomedical materials that will be in the nanoscale powders can be used as raw material for medicine. One of the biomedical materials that can be used as raw material for medicine is of the type of bioceramics is chicken eggshells. This research will develop methods for manufacture nanopowder material from chicken eggshells with Ball Milling using the Taguchi method and ANOVA. Eggshell milled using a variation of Milling rate on 150, 200 and 250 rpm, the time variation of 1, 2 and 3 hours and variations the grinding balls to eggshell powder weight ratio (BPR) 1: 6, 1: 8, 1: 10. Before milled with Ball Milling crushed eggshells in advance and calcinate to a temperature of 900°C. After the milled material characterization of the fine powder of eggshell using SEM to see its size. The result of this research is optimum parameter of Taguchi Design analysis that is 250 rpm milling rate, 3 hours milling time and BPR is 1: 6 with the average eggshell powder size is 1.305 μm. Milling speed, milling time and ball to powder weight of ratio have contribution successively equal to 60.82%, 30.76% and 6.64% by error equal to 1.78%.

From the Cradle to the Grave.

ERIC Educational Resources Information Center

Hill, Jim, Ed.

1994-01-01

Examines the emerging discipline known as life-cycle assessment (LCA) used to evaluate the true environmental impacts of products, materials, or activities from the time raw materials leave the earth until those materials return to their final resting place. (LZ)

Directions for material recovery of used tires and their use in the production of new products intended for the industry of civil construction and pavements

NASA Astrophysics Data System (ADS)

Bulei, C.; Todor, M. P.; Heput, T.; Kiss, I.

2018-01-01

The management of waste from used tires is one of the major principles of recycling and reuse, which involves encouraging a high level of material recovery components, preferably by recycling. Given the current pressure on natural resources on a global scale we must fully take into account the waste in a broader framework defined by the flow of raw materials and their sustainable use. Thus, the opportunity to use various waste from used tires as raw material in order to support economic activities becomes a priority. The recycling of raw materials from waste products and their use in new production processes for their material capitalization is becoming a sustainable approach. Used tire recycling, is the process of recycling waste tires that are no longer suitable for use on vehicles due to wear or irreparable damage. These tires are a problematic source of waste, due to the large volume produced, the durability of the tires, and the components in the tire that are ecologically problematic. Although tires are usually burnt, not recycled, efforts are continuing to find value. Tires can be recycled into, among other things, typically as crumb rubber modifier in recycled pavement. The paper presents aspects of the product resulting from crushing of used tires (powder), which can be used properly valued in the street furniture field or building materials containing rubber.

Peak Doctor v 1.0.0 Labview Version

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garner, Scott

2014-05-29

PeakDoctor software works interactively with its user to analyze raw gamma-ray spectroscopic data. The goal of the software is to produce a list of energies and areas of all of the peaks in the spectrum, as accurately as possible. It starts by performing an energy calibration, creating a function that describes how energy can be related to channel number. Next, the software determines which channels in the raw histogram are in the Compton continuum and which channels are parts of a peak. Then the software fits the Compton continuum with cubic polynomials. The last step is to fit all ofmore » the peaks with Gaussian functions, thus producing the list.« less

Sensory quality and appropriateness of raw and boiled Jerusalem artichoke tubers (Helianthus tuberosus L.).

PubMed

Bach, Vibe; Kidmose, Ulla; Thybo, Anette K; Edelenbos, Merete

2013-03-30

The aim of the present study was to investigate the sensory attributes, dry matter and sugar content of five varieties of Jerusalem artichoke tubers and their relation to the appropriateness of the tubers for raw and boiled preparation. Sensory evaluation of raw and boiled Jerusalem artichoke tubers was performed by a trained sensory panel and a semi-trained consumer panel of 49 participants, who also evaluated the appropriateness of the tubers for raw and boiled preparation. The appropriateness of raw Jerusalem artichoke tubers was related to Jerusalem artichoke flavour, green nut flavour, sweetness and colour intensity, whereas the appropriateness of boiled tubers was related to celeriac aroma, sweet aroma, sweetness and colour intensity. In both preparations the variety Dwarf stood out from the others by being the least appropriate tuber. A few sensory attributes can be used as predictors of the appropriateness of Jerusalem artichoke tubers for raw and boiled consumption. Knowledge on the quality of raw and boiled Jerusalem artichoke tubers can be used to inform consumers on the right choice of raw material and thereby increase the consumption of the vegetable. © 2012 Society of Chemical Industry.

SMART GROUND Project: SMART data collection and inteGRation platform to enhance availability and accessibility of data and infOrmation in the EU territory on SecoNDary Raw Materials

NASA Astrophysics Data System (ADS)

Rossetti, Piergiorgio; Antonella Dino, Giovanna; de la Feld, Marco; Pizza, Antonietta; Coulon, Frederic; Wagland, Stuart; Gomes, Diogo

2016-04-01

The issue of resource security has come to the forefront of the debate over recent years, partly due to considerable concern over the security of supply of the so called 'critical' materials, with rare earths attracting the greatest attention in the press. Their supply is fundamental to maintain and develop EU economy and its industries relied on a steady supply of Raw Materials. Thus considering the increasing scarcity and raising prices of both, energy raw materials and other raw materials, such as metals and minerals, the recycling and recovery of these materials from anthropogenic deposits such as landfills is of increasing relevance. Europe has somewhere between 150,000 and 500,000 landfill sites, with an estimated 90% of them being "non-sanitary" pre-dating the EU Landfill Directive of 1999. Thus historical background makes the numerous old waste dumps as possible sources of critical and secondary raw materials (SRM and CRM). However, to date there is no inventory available of SRM and CRM present in EU landfills, and best management practices to recover SRM from landfill activities are inefficient. In this context, the EU SMART GROUND (SG) project (Grant Agreement No 641988) intends to foster resource recovery in landfills by improving both the availability and the accessibility of data and information on SRM in the EU and creating synergies among the different stakeholders involved in the SRM value chain. To do so, the project aims to collect and integrate in a single EU databank (SMART GROUND Data Bank) all the data from existing databases and new information retrieved during project activities. Such data will be collected from the different waste streams including municipal, industrial and mining wastes across EU landfills. It will improve data gathering on SRM from different types of waste, by defining new and integrated data acquisition methods and standards. At last, but not least, the project will also improve the SRM economic and employment potential, by i) providing training on the assessment of landfill sites material recovery to targeting end-users, ii) establishing a dedicated network of academic, industrial, regulators and other stakeholders committed to cost-effective research, technology transfer and training. The present contribution will provide an overview of the SMART GROUND project and highlights the results obtained during the first six months of project activity.

Management and characteristics of recycled manure solids used for bedding in Midwest freestall dairy herds.

PubMed

Husfeldt, A W; Endres, M I; Salfer, J A; Janni, K A

2012-04-01

Interest in using recycled manure solids (RMS) as a bedding material for dairy cows has grown in the US Midwest. Cost of common bedding materials has increased in recent years and availability has decreased. Information regarding the composition of RMS and its use as a bedding material for dairy cows in the Midwest is very limited. The objectives of this study were to characterize RMS as a bedding material, observe bedding management practices, document methods of obtaining RMS, and describe housing facilities. We visited 38 Midwest dairy operations bedding freestalls with RMS to collect data. Methods of obtaining RMS for bedding included separation of anaerobic digested manure, separation of raw manure, and separation of raw manure followed by mechanical drum-composting for 18 to 24 h. Average bedding moisture of unused RMS was 72.4% with a pH of 9.16. Unused samples contained (on a dry basis) 1.4% N, 44.9% C, 32.7C:N ratio, 0.44% P, 0.70% K, 76.5% neutral detergent fiber, 9.4% ash, 4.4% nonfiber carbohydrates, and 1.1% fat. Moisture was lowest for drum-composted solids before and after use as freestall bedding. After use in the stalls, digested solids had lower neutral detergent fiber content (70.5%) than drum-composted (75.0%) and separated raw (73.1%) solids. Total N content was greater in digested solids (2.0%) than in separated raw (1.7%) solids. Total bacterial populations in unused bedding were greatest in separated raw manure solids but were similar between digested and drum-composted manure solids. Drum-composted manure solids had no coliform bacteria before use as freestall bedding. After use as bedding, digested manure solids had lower total bacteria counts compared with drum-composted and separated raw manure solids, which had similar counts. Used bedding samples of digested solids contained fewer environmental streptococci than drum-composted and separated raw solids and had reduced Bacillus counts compared with separated raw solids. Coliform counts were similar for all 3 bedding sources. Addition of a mechanical blower post-separation and use of a shelter for storage were associated with reduced fresh-bedding moisture but not associated with bacterial counts. This was the first survey of herds using RMS for bedding in the Midwest. We learned that RMS was being used successfully as a source of bedding for dairy cows. For most farms in the study, somatic cell count was comparable to the average in the region and not excessively high. Copyright © 2012 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Preparation of polyol esters based on vegetable and animal fats.

PubMed

Gryglewicz, S; Piechocki, W; Gryglewicz, G

2003-03-01

The possibility of using some natural fats: rapeseed oil, olive oil and lard, as starting material for the preparation of neopentyl glycol (NPG) and trimethylol propane (TMP) esters is reported. The syntheses of final products were performed by alcoholysis of fatty acid methyl esters, obtained from natural fats studied, with the appropriate polyhydric alcohol using calcium methoxide as a catalyst. The basic physicochemical properties of the NPG and TMP esters synthesized were the following: viscosity at 40 degrees C in the range of 13.5-37.6 cSt, pour point between -10.5 and -17.5 degrees C and very high viscosity indices, higher than 200. Generally, the esters of neopentyl alcohols were characterized by higher stability in thermo-oxidative conditions in comparison to native triglycerides. Due to the low content of polyunsaturated acids, the olive oil based esters showed the highest thermo-oxidative resistance. Also, methyl esters of fatty acids of lard would constitute a good raw material for the synthesis of lubricating oils, provided that their saturated acids content was lowered. This permits synthesis of NPG and TMP esters with a lower pour point (below -10 degrees C) than natural lard (+33 degrees C).

The Use of Tunnel Muck as Industrial Raw Material: Two Case-Studies

NASA Astrophysics Data System (ADS)

Marini, P.; Bellopede, R.

2013-03-01

The re-use of rock as an industrial material requires more treatments than those foreseen for the reuse of muck as an aggregate for concrete and for road construction. The treatments always start with comminution, which has the goal of liberating the rock-forming minerals. Liberation is achieved with the appearance of grains which are composed of only one mineral. The subsequent treatment steps are based on the physical-mechanical-chemical properties of the different minerals, that is, density, magnetic susceptibility, wettability etc. Magnetic separation and flotation, the two techniques examined in this research, are the two most common techniques used in industrial mineral production plants. The mucks that were analysed are from the Omegna and Brennero tunnels, both of which are granitic rocks with different textures. From the analysis and comparison of the preliminary treatment results, it has been possible to optimise the treatment method. Petrographic, mineralogic and firing tests have been conducted to evaluate the obtained results. High-gradient magnetic separation (HGMS) on defined grain sizes appears to be suitable to obtain a product with a high feldspar-quartz content which could be used in the ceramic field.

Investigation of the influence of pretreatment parameters on the surface characteristics of amorphous metal for use in power industry

NASA Astrophysics Data System (ADS)

Nieroda, Jolanta; Rybak, Andrzej; Kmita, Grzegorz; Sitarz, Maciej

2018-05-01

Metallic glasses are metallic materials, which exhibit an amorphous structure. These are mostly three or more component alloys, and some of them are magnetic metals. Materials of this kind are characterized by high electrical resistivity and at the same time exhibit very good magnetic properties (e.g. low-magnetization loss). The above mentioned properties are very useful in electrical engineering industry and this material is more and more popular as a substance for high-efficiency electrical devices production. This industry area is still evolving, and thus even higher efficiency of apparatus based on amorphous material is expected. A raw material must be carefully investigated and characterized before the main production process is started. Presented work contains results of complementary examination of amorphous metal Metglas 2605. Studies involve two ways to obtain clean and oxidized surface with high reactivity, namely degreasing followed by annealing process and plasma treatment. The amorphous metal parameters were examined by means of several techniques: surface free energy (SFE) measurements by sessile drop method, X-ray Photoelectron Spectroscopy (XPS), Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD), and both ex situ and in situ Raman spectroscopy. Additionally, influence of plasma parameters on wetting properties were optimized in systematic way with Design of Experiments (DOE) method. A wide range of used methods allow to fully investigate the amorphous metal material during preliminary preparation of surface. Obtained results provide information about appropriate parameters that should be applied in order to obtain highly reactive surface with functional oxide layer on it.

Study on the Particle Size Distribution Nano-Particles of Mining Minerals on Whiteness of Triaxial Body

NASA Astrophysics Data System (ADS)

Mathur, Ravi; Soni, Aditi

White wares produced worldwide represent the foundation of much of the ceramic industry; Porcelain bodies fabricated from triaxial mixtures of clay, quartz and feldspar with different size and amounts of nano particles were investigated. Although the purity of raw materials has a strong effect on the colour of the fired bodies, the particle size of raw materials also effect the whiteness The raw material mining minerals china Clay, Feldspar, quarts were prepared of various sized nano particles contains 10.60 -20.22%, 56.84- 70.80 % and 34.87-50.76 % of 100nm respectively. The fired bodies of raw mining minerals and triaxial bodies were subjected to colour measurement. The differences in whiteness were compared and discussed. The studies so far carried out is upto 400 mesh size while the present study has included up to 100nm particle size. A statistical correlation between whiteness of feldspar and triaxial body was also carried out. The correlation between china clay and triaxial body are 0.53, 0.57 and 0.66 for china clay similarly correlation for feldspar is 0.49, 0.73 and 0.83 for triaxial body it are 0.97, 0.84 and 0.75 for A1, A2 and A3 samples. Correlation between china clay and feldspar with triaxial body are 0.79 and 0.92 respectively.

Flexible chitosan-nano ZnO antimicrobial pouches as a new material for extending the shelf life of raw meat.

PubMed

Rahman, P Mujeeb; Mujeeb, V M Abdul; Muraleedharan, K

2017-04-01

As a breakthrough to open up the industrial use of novel environmentally benign packaging material, we propose the first report on portable chitosan-ZnO nano-composite pouches that will serve as elite entrants in smart packaging. A facile, one pot procedure was adopted for the preparation of the C-ZnC films. In order to tune the property of C-ZnC films, four different composite films were prepared by varying the concentration of ZnO. The prepared films were found to be much superior when compared to bare chitosan and other conventional films. Two bacterial strains that commonly contaminate in packed meat were selected as target microbes to elucidate the antimicrobial activity of the prepared C-ZnO film. Detailed investigations revealed that the antimicrobial efficiency is linearly related to the amount of ZnO nano-particles in the composite. The C-2 films exhibited excellent antimicrobial activity and was fabricated into packaging pouches for raw meat. The prepared pouches showed significant action against the microbes in raw meat owing to its complete inhibition of microbial growth on the sixth day of storage at 4°C. The C-2 pouches stand as a top-notch material when compared to polyethylene bag in extending the shelf life of raw meat. Copyright © 2017 Elsevier B.V. All rights reserved.

Beneficiation of Kulon Progo iron sand by using tabling and magnetic separation methods

NASA Astrophysics Data System (ADS)

Oediyani, Soesaptri; Ikhlasul Amal, M.; M. Victoriyan, N.; Juniarsih, Andinnie

2018-04-01

There are two types of iron resources such as primary iron ore and iron sand. In general, primary iron ores use as raw materials in iron and steel making because the iron content is high (± 60%) and can reduce directly. On the other and, iron sand is rarely used as a raw material because the iron content is low (20-40%) but the iron sand reserves are very abundant in Indonesia for instance is about 173 million tons in Kulon Progo, Jogyakarta. In addition, the new regulation of Energy and Mineral Resources Ministry required that iron sands must process before are being export. Therefore, the proper beneficiation methods are need to improve the iron content of iron sand. In this research Kulon Progo iron sand was used as a raw materials because not only the reserves very abundant but also the new iron making plant will build here soon. The combine of ore concentration methods such as tabling and magnetic separation used to improve the iron content. Then, the variable process were inclination of the table (2°,3° and 4°), fraction of feed size (-100 mesh, -150 mesh and -200 mesh) and the magnetic intensity (176, 830, 1500 Gauss). The highest recovery was about 96.75% and the concentrate which is contain 59.78 % Fe achieved by using -200 mesh particle size, 4° inclination of table and 1500 Gauss as a magnetic intensity. In conclusion, this concentrate fulfilled raw material requires of iron making (≥ 55%Fe).

Sewage sludge as a fuel and raw material for phosphorus recovery: Combined process of gasification and P extraction.

PubMed

Gorazda, K; Tarko, B; Werle, S; Wzorek, Z

2018-03-01

Increasing problems associated with sewage sludge disposal are observed nowadays. As the thermal conversion of sewage sludge (combustion, co-combustion, gasification and pyrolysis) appears to be the most promising alternative for its management, the solid residues left after gasification were examined. The present study evaluates the potential of this waste as an alternative phosphorus source in the context of phosphorus recovery. The obtained solid gasification residues were characterised (chemical and phase composition, thermal properties, surface properties and technological parameters used for phosphorus raw materials) and compared to commercial phosphate raw materials. It was revealed that gasification residue is a valuable source of phosphorus and microelements, comparable to sewage sludge ash (SSA) considered nowadays as secondary phosphorus raw materials. Chemical properties as well as technological parameters characteristic for natural phosphate ores are different. Solid gasification residue was leached with mineral acids (phosphoric and nitric) according to the patented method of phosphorus recovery - PolFerAsh, developed by Cracow University of Technology. It was revealed that phosphorus can be selectively leached from solid gasification residue with high efficiency (73-82%); moreover, most of the iron and heavy metals stay in the solid phase due to the low concentration of acids and proper solid to liquid phase ratio. The obtained leachates are valuable products that can be considered for the production of fertilisers. Combining the gasification process with nutrient recovery provides the opportunity for more environmentally efficient technologies driven by sustainable development rules. Copyright © 2017 Elsevier Ltd. All rights reserved.

Chemical and thermal studies on esterification of EDTA with raw cellulose and mercerized cellulose EFB

NASA Astrophysics Data System (ADS)

Azamkamal, Fatihah; Zakaria, Sarani; Gan, Sinyee; Kaco, Hatika

2018-04-01

Oil palm empty fruit bunch fibre (EFB) was bleached using four stages bleaching sequences (DEED) where D was a bleaching process composed of 1.7 wt% NaClO2 and buffer solution while E was composed of NaOH solution. Raw cellulose and mercerized cellulose which treated with 3.5 N sodium hydroxide were used as a raw material for esterification with ethylenediaminetetraacetic acid (EDTA) and enhancement with acetic acid. The samples of raw cellulose and mercerized cellulose were observed using optical microscope. The thermal properties of raw cellulose and mercerized cellulose esterified with EDTA were studied. The effect of mercerized cellulose on esterification process of EDTA was investigated. The studies suggested that the mercerization process affect the thermal stability of the cellulose. The transmittance of FTIR band showed that raw cellulose gave better esterification product compared to mercerized cellulose. Hence, the mercerization process of cellulose does not improve the esterification of cellulose with EDTA.

Heat inactivation of poliovirus in wastewater sludge

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ward, R.L.; Ashley, C.S.; Moseley, R.H.

1976-09-01

The effect of raw and anaerobically digested sludge on heat inactivation of poliovirus was investigated. Raw sludge was found to be very protective of poliovirus plaque-forming ability at all temperatures studied, but digested sludge had variable effects that were highly dependent upon the experimental conditions. In low concentrations and at relatively low inactivation temperatures, digested sludge is nearly as protective of poliovirus as raw sludge. However, at higher temperatures and concentrations, digested sludge caused a significant acceleration of poliovirus inactivation. The difference between the protective capability of raw and digested sludge is not due to loss of protective material, becausemore » this component is present in the solids of digested sludge as well as in those of raw sludge. Instead, the difference is due to a virucidal agent acquired during digestion. Addition of this agent to the solids of either raw or digested sludge reverses the protective potential of these solids during heat treatment of poliovirus.« less