40 CFR 60.46c - Emission monitoring for sulfur dioxide.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Emission monitoring for sulfur dioxide... Industrial-Commercial-Institutional Steam Generating Units § 60.46c Emission monitoring for sulfur dioxide... the inlet to the steam generating unit and analyzed for sulfur content and heat content according the...

Steam dispatching control system demonstration at Fort Benjamin Harrison. Final technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Diks, C.L.; Moshage, R.E.; Lin, M.C.

1993-07-01

Currently most Army Central steam heating systems operate by maintaining a constant steam pressure regardless of actual steam demand. This method offers some operational convenience, but is often the cause of significant energy losses. Researchers at the U.S. Army Construction Engineering Research Laboratories (USACERL) have investigated the Steam Dispatching Control System (SDCS), a control system that lowers supply steam pressure-and therefore steam temperature-to slightly above the amount needed to meet the steam demand. The lower Steam temperature and reduction in steam loss (from leaks and faulty traps) result in lower heat losses and higher energy savings. Limiting steam pressure canmore » diminish the amount of excess heat loss in the distribution system while still meeting the demand. The Army's Facilities Engineering Applications Program (FEAP) chose Fort Benjamin Harrison, IN, as the Army demonstration site for SDCS. Researchers found that use of SDCS is technically and economically viable improvement over current operating procedures. Analysis based on demonstration results show that the simple payback for SDCS is less than 1 year. The results of this demonstration are generally applicable to installations with a large central heating plant and a substantial steam distribution system. Findings, indicate that energy savings form SDCS are significant regardless of what type of fuel powers the boiler. The authors note that, during the initial evaluation of a potential SDCS application, attention must be paid to the condensate return to ensure that it will operate properly. Fort Benjamin Harrison, IN, Steam Dispatching Control System(SDCS), Central heating plants, energy conservation.« less

Intelligent Chemistry Management System (ICMS)--A new approach to steam generator chemistry control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barto, R.J.; Farrell, D.M.; Noto, F.A.

1986-04-01

The Intelligent Chemistry Management System (ICMS) is a new tool which assists in steam generator chemistry control. Utilizing diagnostic capabilities, the ICMS will provide utility and industrial boiler operators, system chemists, and plant engineers with a tool for monitoring, diagnosing, and controlling steam generator system chemistry. By reducing the number of forced outages through early identification of potentially detrimental conditions, suggestion of possible causes, and execution of corrective actions, improvements in unit availability and reliability will result. The system monitors water and steam quality at a number of critical locations in the plant.

French Regulatory practice and experience feedback on steam generator tube integrity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sandon, G.

1997-02-01

This paper summarizes the way the French Safety Authority applies regulatory rules and practices to the problem of steam generator tube cracking in French PWR reactors. There are 54 reactors providing 80% of French electrical consumption. The Safety Authority closely monitors the performance of tubes in steam generators, and requires application of a program which deals with problems prior to the actual development of leakage. The actual rules regarding such performance are flexible, responding to the overall performance of operating steam generators. In addition there is an inservice inspection service to examine tubes during shutdown, and to monitor steam generatorsmore » for leakage during operation, with guidelines for when generators must be pulled off line.« less

High Temperature Ultrasonic Probe and Pulse-Echo Probe Mounting Fixture for Testing and Blind Alignment on Steam Pipes

NASA Technical Reports Server (NTRS)

Lih, Shyh-Shiuh (Inventor); Takano, Nobuyuki (Inventor); Lee, Hyeong Jae (Inventor); Bao, Xiaoqi (Inventor); Badescu, Mircea (Inventor); Bar-Cohen, Yoseph (Inventor); Sherrit, Stewart (Inventor); Ostlund, Patrick N. (Inventor)

2017-01-01

A high temperature ultrasonic probe and a mounting fixture for attaching and aligning the probe to a steam pipe using blind alignment. The high temperature ultrasonic probe includes a piezoelectric transducer having a high temperature. The probe provides both transmitting and receiving functionality. The mounting fixture allows the high temperature ultrasonic probe to be accurately aligned to the bottom external surface of the steam pipe so that the presence of liquid water in the steam pipe can be monitored. The mounting fixture with a mounted high temperature ultrasonic probe are used to conduct health monitoring of steam pipes and to track the height of condensed water through the wall in real-time.

[Sterilization effect analysis of B-class pulsation table top vacuum sterilizer to dental handpieces].

PubMed

Zeng, Shu-Rong; Jiang, Bo; Xiao, Xiao-Rong

2007-06-01

Discuss sterilization effect of B-class pulsation table top vacuum pressure steam sterilizer for dental handpiece. Analysis selection of sterilizer for dental handpiece and sterilization management processes and sterilization effect monitoring, evaluation of monitoring result and effective sterilization method. The B-class pulsation table top vacuum pressure steam sterilizer to dental handpiece in West China Stomatological Hospital of Sichuan University met the requirement of the chemical and biological monitoring. Its efficiency of sterilization was 100%. The results of aerobic culture, anaerobic culture, B-type hepatitis mark monitoring to sterilized dental handpiece were negative. It is effective method for dental handpiece sterilization to use B-class pulsation table top vacuum pressure steam sterilizer.

7 CFR 58.738 - Pasteurized process cheese spread and related products.

Code of Federal Regulations, 2013 CFR

2013-01-01

... homogeneous plastic mass, and be free from pin holes or openings except those caused by trapped steam. Product made for slicing shall slice freely when cut into approximately 1/8 inch slices with only a slight...

7 CFR 58.738 - Pasteurized process cheese spread and related products.

Code of Federal Regulations, 2014 CFR

2014-01-01

... homogeneous plastic mass, and be free from pin holes or openings except those caused by trapped steam. Product made for slicing shall slice freely when cut into approximately 1/8 inch slices with only a slight...

7 CFR 58.738 - Pasteurized process cheese spread and related products.

Code of Federal Regulations, 2012 CFR

2012-01-01

... homogeneous plastic mass, and be free from pin holes or openings except those caused by trapped steam. Product made for slicing shall slice freely when cut into approximately 1/8 inch slices with only a slight...

Effects of different cooking methods on nutritional and physicochemical characteristics of selected vegetables.

PubMed

Miglio, Cristiana; Chiavaro, Emma; Visconti, Attilio; Fogliano, Vincenzo; Pellegrini, Nicoletta

2008-01-09

The objective of the present study was to evaluate the effect of three common cooking practices (i.e., boiling, steaming, and frying) on phytochemical contents (i.e., polyphenols, carotenoids, glucosinolates, and ascorbic acid), total antioxidant capacities (TAC), as measured by three different analytical assays [Trolox equivalent antioxidant capacity (TEAC), total radical-trapping antioxidant parameter (TRAP), ferric reducing antioxidant power (FRAP)] and physicochemical parameters of three vegetables (carrots, courgettes, and broccoli). Water-cooking treatments better preserved the antioxidant compounds, particularly carotenoids, in all vegetables analyzed and ascorbic acid in carrots and courgettes. Steamed vegetables maintained a better texture quality than boiled ones, whereas boiled vegetables showed limited discoloration. Fried vegetables showed the lowest degree of softening, even though antioxidant compounds were less retained. An overall increase of TEAC, FRAP, and TRAP values was observed in all cooked vegetables, probably because of matrix softening and increased extractability of compounds, which could be partially converted into more antioxidant chemical species. Our findings defy the notion that processed vegetables offer lower nutritional quality and also suggest that for each vegetable a cooking method would be preferred to preserve the nutritional and physicochemical qualities.

40 CFR 60.4335 - How do I demonstrate compliance for NOX if I use water or steam injection?

Code of Federal Regulations, 2011 CFR

2011-07-01

... monitor and record the fuel consumption and the ratio of water or steam to fuel being fired in the turbine... continuous emission monitoring system (CEMS) consisting of a NOX monitor and a diluent gas (oxygen (O2) or... rate, temperature, and pressure, to continuously measure the total thermal energy output in British...

40 CFR 60.4335 - How do I demonstrate compliance for NOX if I use water or steam injection?

Code of Federal Regulations, 2014 CFR

2014-07-01

... monitor and record the fuel consumption and the ratio of water or steam to fuel being fired in the turbine... continuous emission monitoring system (CEMS) consisting of a NOX monitor and a diluent gas (oxygen (O2) or... rate, temperature, and pressure, to continuously measure the total thermal energy output in British...

40 CFR 60.4335 - How do I demonstrate compliance for NOX if I use water or steam injection?

Code of Federal Regulations, 2010 CFR

2010-07-01

... monitor and record the fuel consumption and the ratio of water or steam to fuel being fired in the turbine... continuous emission monitoring system (CEMS) consisting of a NOX monitor and a diluent gas (oxygen (O2) or... rate, temperature, and pressure, to continuously measure the total thermal energy output in British...

40 CFR 60.4335 - How do I demonstrate compliance for NOX if I use water or steam injection?

Code of Federal Regulations, 2012 CFR

2012-07-01

... monitor and record the fuel consumption and the ratio of water or steam to fuel being fired in the turbine... continuous emission monitoring system (CEMS) consisting of a NOX monitor and a diluent gas (oxygen (O2) or... rate, temperature, and pressure, to continuously measure the total thermal energy output in British...

40 CFR 60.4335 - How do I demonstrate compliance for NOX if I use water or steam injection?

Code of Federal Regulations, 2013 CFR

2013-07-01

... monitor and record the fuel consumption and the ratio of water or steam to fuel being fired in the turbine... continuous emission monitoring system (CEMS) consisting of a NOX monitor and a diluent gas (oxygen (O2) or... rate, temperature, and pressure, to continuously measure the total thermal energy output in British...

Optical wet steam monitor

DOEpatents

Maxey, L.C.; Simpson, M.L.

1995-01-17

A wet steam monitor determines steam particle size by using laser doppler velocimeter (LDV) device to produce backscatter light. The backscatter light signal is processed with a spectrum analyzer to produce a visibility waveform in the frequency domain. The visibility waveform includes a primary peak and a plurality of sidebands. The bandwidth of at least the primary frequency peak is correlated to particle size by either visually comparing the bandwidth to those of known particle sizes, or by digitizing the waveform and comparing the waveforms electronically. 4 figures.

Optical wet steam monitor

DOEpatents

Maxey, Lonnie C.; Simpson, Marc L.

1995-01-01

A wet steam monitor determines steam particle size by using laser doppler velocimeter (LDV) device to produce backscatter light. The backscatter light signal is processed with a spectrum analyzer to produce a visibility waveform in the frequency domain. The visibility waveform includes a primary peak and a plurality of sidebands. The bandwidth of at least the primary frequency peak is correlated to particle size by either visually comparing the bandwidth to those of known particle sizes, or by digitizing the waveform and comparing the waveforms electronically.

Distributed acoustic sensing technique and its field trial in SAGD well

NASA Astrophysics Data System (ADS)

Han, Li; He, Xiangge; Pan, Yong; Liu, Fei; Yi, Duo; Hu, Chengjun; Zhang, Min; Gu, Lijuan

2017-10-01

Steam assisted gravity drainage (SAGD) is a very promising way for the development of heavy oil, extra heavy oil and tight oil reservoirs. Proper monitoring of the SAGD operations is essential to avoid operational issues and improve efficiency. Among all the monitoring techniques, micro-seismic monitoring and related interpretation method can give useful information about the steam chamber development and has been extensively studied. Distributed acoustic sensor (DAS) based on Rayleigh backscattering is a newly developed technique that can measure acoustic signal at all points along the sensing fiber. In this paper, we demonstrate a DAS system based on dual-pulse heterodyne demodulation technique and did field trial in SAGD well located in Xinjiang Oilfield, China. The field trail results validated the performance of the DAS system and indicated its applicability in steam-chamber monitoring and hydraulic monitoring.

Use of borehole radar tomography to monitor steam injection in fractured limestone

USGS Publications Warehouse

Gregoire, C.; Joesten, P.K.

2006-01-01

Borehole radar tomography was used as part of a pilot study to monitor steam-enhanced remediation of a fractured limestone contaminated with volatile organic compounds at the former Loring Air Force Base, Maine, USA. Radar tomography data were collected using 100-MHz electric-dipole antennae before and during steam injection to evaluate whether cross-hole radar methods could detect changes in medium properties resulting from the steam injection. Cross-hole levelrun profiles, in which transmitting and receiving antennae are positioned at a common depth, were made before and after the collection of each full tomography data set to check the stability of the radar instruments. Before tomographic inversion, the levelrun profiles were used to calibrate the radar tomography data to compensate for changes in traveltime and antenna power caused by instrument drift. Observed changes in cross-hole radar traveltime and attenuation before and during steam injection were small. Slowness- and attenuation-difference tomograms indicate small increases in radar slowness and attenuation at depths greater than about 22 m below the surface, consistent with increases in water temperature observed in the boreholes used for the tomography. Based on theoretical modelling results, increases in slowness and attenuation are interpreted as delineating zones where steam injection heating increased the electrical conductivity of the limestone matrix and fluid. The results of this study show the potential of cross-hole radar tomography methods to monitor the effects of steam-induced heating in fractured rock environments. ?? 2006 European Association of Geoscientists & Engineers.

Back Propagation Artificial Neural Network and Its Application in Fault Detection of Condenser Failure in Thermo Plant

NASA Astrophysics Data System (ADS)

Ismail, Firas B.; Thiruchelvam, Vinesh

2013-06-01

Steam condenser is one of the most important equipment in steam power plants. If the steam condenser trips it may lead to whole unit shutdown, which is economically burdensome. Early condenser trips monitoring is crucial to maintain normal and safe operational conditions. In the present work, artificial intelligent monitoring systems specialized in condenser outages has been proposed and coded within the MATLAB environment. The training and validation of the system has been performed using real operational measurements captured from the control system of selected steam power plant. An integrated plant data preparation scheme for condenser outages with related operational variables has been proposed. Condenser outages under consideration have been detected by developed system before the plant control system"

A comparison of trapping methods for Tabanidae (Diptera) in North Queensland, Australia.

PubMed

van Hennekeler, K; Jones, R E; Skerratt, L F; Fitzpatrick, L A; Reid, S A; Bellis, G A

2008-03-01

The ability to monitor the abundance and diversity of tabanid flies over wide areas requires effective and low-cost surveillance methods. Such monitoring activities help to quantify the risk of transmission of pathogens by tabanids. Here we examine the effectiveness and practicality of two types of trap (canopy traps and Nzi traps) and two types of attractant (octenol and carbon dioxide) for monitoring tabanid flies in tropical Australia. The Nzi trap consistently caught more tabanids and more species of tabanids than the canopy trap. It was also more robust and therefore required less maintenance in remote locations. The use of attractants substantially increased capture rates, both of individuals and species, and traps using both attractants were consistently the most effective. However, in remote locations, where it is not possible to check traps frequently, the use of attractants may not be feasible. When attractants were not used, the canopy trap caught very few tabanids, but the Nzi trap remained effective enough to be useful as a monitoring device. In addition, the number of tabanid species caught by the Nzi traps remained high, and included those that were most abundant. We therefore conclude that, in this region, Nzi traps are preferable for tabanid monitoring and that attractants greatly improve their effectiveness. However, for longterm monitoring, especially in remote locations, Nzi traps without attractants are a satisfactory option.

Steam ejector-condenser: stage I of a differential vacuum pumping station

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hanson, C.L.; Alger, T.W.

1981-04-01

A steam ejector-condenser unit was built and tested to produce a 10 Torr (13.3 x 10/sup 2/Pa) vacuum with a 2 cm aperture to the atmosphere. This unit is the first stage of a differential vacuum pumping station that will be used with the Experimental Test Accelerator. The accelerator's electron beam will pass through a series of openings from a high vacuum (5 x 10/sup -6/ Torr) to the atmosphere. The differential system consists of four vacuum pumping units separated by 2 cm-diam apertures. Superheated steam is injected near the final beamline orifice to reduce the quantity of atmospheric airmore » flowing into the steam ejector--condenser unit. The steam ejector in the condenser vessel is open at its center to permit passage of the accelerator beam. Five nozzles mounted in a conical array produce the ejector vacuum of 10 Torr. The ejector exhausts into the condenser and forms a barrier to air flow into the lower pressure region. This feature permits high volume cold trapping and cryopumping of water vapor in the remaining lower-pressure stages. Tests have proven that the steam ejector--condenser is a reliable operating unit and suitable for long-term, steady-state accelerator operation.« less

In situ analysis of chemical components induced by steaming between fresh ginseng, steamed ginseng, and red ginseng.

PubMed

In, Gyo; Ahn, Nam-Geun; Bae, Bong-Seok; Lee, Myoung-Woo; Park, Hee-Won; Jang, Kyoung Hwa; Cho, Byung-Goo; Han, Chang Kyun; Park, Chae Kyu; Kwak, Yi-Seong

2017-07-01

The chemical constituents of Panax ginseng are changed by processing methods such as steaming or sun drying. In the present study, the chemical change of Panax ginseng induced by steaming was monitored in situ . Samples were separated from the same ginseng root by incision during the steaming process, for in situ monitoring. Sampling was sequentially performed in three stages; FG (fresh ginseng) → SG (steamed ginseng) → RG (red ginseng) and 60 samples were prepared and freeze dried. The samples were then analyzed to determine 43 constituents among three stages of P. ginseng . The results showed that six malonyl-ginsenoside (Rg1, Rb1, Rb3, Rc, Rd, Rb2) and 15 amino acids were decreased in concentration during the steaming process. In contrast, ginsenoside-Rh1, 20( S )-Rg2, 20( S, R )-Rg3 and Maillard reaction product such as AF (arginine-fructose), AFG (arginine-fructose-glucose), and maltol were newly generated or their concentrations were increased. This study elucidates the dynamic changes in the chemical components of P. ginseng when the steaming process was induced. These results are thought to be helpful for quality control and standardization of herbal drugs using P. ginseng and they also provide a scientific basis for pharmacological research of processed ginseng (Red ginseng).

40 CFR 60.4380 - How are excess emissions and monitor downtime defined for NOX?

Code of Federal Regulations, 2011 CFR

2011-07-01

... and monitor downtime that must be reported are defined as follows: (a) For turbines using water or... is injected into the turbine when a fuel is being burned that requires water or steam injection for... operating hour in which water or steam is injected into the turbine, but the essential parametric data...

40 CFR 60.4380 - How are excess emissions and monitor downtime defined for NOX?

Code of Federal Regulations, 2012 CFR

2012-07-01

... and monitor downtime that must be reported are defined as follows: (a) For turbines using water or... is injected into the turbine when a fuel is being burned that requires water or steam injection for... operating hour in which water or steam is injected into the turbine, but the essential parametric data...

40 CFR 60.4380 - How are excess emissions and monitor downtime defined for NOX?

Code of Federal Regulations, 2010 CFR

2010-07-01

... and monitor downtime that must be reported are defined as follows: (a) For turbines using water or... is injected into the turbine when a fuel is being burned that requires water or steam injection for... operating hour in which water or steam is injected into the turbine, but the essential parametric data...

40 CFR 60.4380 - How are excess emissions and monitor downtime defined for NOX?

Code of Federal Regulations, 2014 CFR

2014-07-01

... and monitor downtime that must be reported are defined as follows: (a) For turbines using water or... is injected into the turbine when a fuel is being burned that requires water or steam injection for... operating hour in which water or steam is injected into the turbine, but the essential parametric data...

40 CFR 60.4380 - How are excess emissions and monitor downtime defined for NOX?

Code of Federal Regulations, 2013 CFR

2013-07-01

... and monitor downtime that must be reported are defined as follows: (a) For turbines using water or... is injected into the turbine when a fuel is being burned that requires water or steam injection for... operating hour in which water or steam is injected into the turbine, but the essential parametric data...

A Home-Made Trap Baited With Sex Pheromone for Monitoring Spodoptera Frugiperda Males (Lepidoptera: Noctuidae) in Corn crops in Mexico.

PubMed

Malo, Edi A; Cruz-Esteban, Samuel; González, Francisco J; Rojas, Julio C

2018-05-15

Fall armyworm (FAW), Spodoptera frugiperda (J. E. Smith), populations are monitored with a variety of commercial sex pheromone-baited traps. However, a number of trap-related variables may affect the number of FAW males captured. In this study, we tested the effect of trap design, trap size, and trap color for monitoring FAW males in corn crops in Mexico. We found that plastic jug trap (a home-made trap), captured significantly more FAW males than a commercial trap (Scentry Heliothis) and water bottle trap (another home-made trap). We also found that size of plastic jug traps (3.78, 10, or 20 liters) did not affect the captures of FAW males. Our results indicated that plastic yellow jug traps captured significantly more males than blue and black traps. Plastic jug white, red, and green traps captured a similar number of FAW males than plastic jug yellow, blue, and black traps. Plastic jug blue, white, and yellow traps captured more nontarget insects compared to black traps. The number of nontarget insects captured by green and red traps was similar and not significantly different to that caught by blue, white, yellow, and black traps. Traps captured more individuals from Diptera than Coleoptera and Hymenoptera. Overall, the results suggest that yellow plastic jug may be used for monitoring FAW males in corn and sorghum crops in Mexico.

Precise and low-cost monitoring of plum curculio (Coleoptera: Curculionidae) pest activity in pyramid traps with cameras.

PubMed

Selby, R D; Gage, S H; Whalon, M E

2014-04-01

Incorporating camera systems into insect traps potentially benefits insect phenology modeling, nonlethal insect monitoring, and research into the automated identification of traps counts. Cameras originally for monitoring mammals were instead adapted to monitor the entrance to pyramid traps designed to capture the plum curculio, Conotrachelus nenuphar (Herbst) (Coleoptera: Curculionidae). Using released curculios, two new trap designs (v.I and v.II) were field-tested alongside conventional pyramid traps at one site in autumn 2010 and at four sites in autumn 2012. The traps were evaluated on the basis of battery power, ease-of-maintenance, adaptability, required-user-skills, cost (including labor), and accuracy-of-results. The v.II design fully surpassed expectations, except that some trapped curculios were not photographed. In 2012, 13 of the 24 traps recorded every curculio entering the traps during the 18-d study period, and in traps where some curculios were not photographed, over 90% of the omissions could be explained by component failure or external interference with the motion sensor. Significantly more curculios entered the camera traps between 1800 and 0000 hours. When compared with conventional pyramid traps, the v.I traps collected a similar number of curculios. Two observed but not significant trends were that the v.I traps collected twice as many plum curculios as the v.II traps, while at the same time the v.II traps collected more than twice as many photos per plum curculio as the v.I traps. The research demonstrates that low-cost, precise monitoring of field insect populations is feasible without requiring extensive technical expertise.

InSAR Monitoring of Surface Deformation in Alberta's Oil Sands

NASA Astrophysics Data System (ADS)

Pearse, J.; Singhroy, V.; Li, J.; Samsonov, S. V.; Shipman, T.; Froese, C. R.

2013-05-01

Alberta's oil sands are among the world's largest deposits of crude oil, and more than 80% of it is too deep to mine, so unconventional in-situ methods are used for extraction. Most in situ extraction techniques, such as Steam-Assisted Gravity Drainage (SAGD), use steam injection to reduce the viscosity of the bitumen, allowing it to flow into wells to be pumped to the surface. As part of the oil sands safety and environmental monitoring program, the energy regulator uses satellite radar to monitor surface deformation associated with in-situ oil extraction. The dense vegetation and sparse infrastructure in the boreal forest of northern Alberta make InSAR monitoring a challenge; however, we have found that surface heave associated with steam injection can be detected using traditional differential InSAR. Infrastructure and installed corner reflectors also allow us to use persistent scatterer methods to obtain time histories of deformation at individual sites. We have collected and processed several tracks of RADARSAT-2 data over a broad area of the oil sands, and have detected surface deformation signals of approximately 2-3 cm per year, with time series that correlate strongly with monthly SAGD steam injection volumes.

Continuous on-line steam quality monitoring system of the Bacman Geothermal Production Field, Philippines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Solis, R.P.; Chavez, F.C.; Garcia, S.E.

1997-12-31

In any operating geothermal power plant, steam quality is one of the most important parameters being monitored. In the Bacon-Manito Geothermal Production Field (BGPF), an online steam quality monitoring system have been installed in two operating power plants which provides an accurate, efficient and continuous real-time data which is more responsive to the various requirements of the field operation. The system utilizes sodium as an indicator of steam purity. Sodium concentration is read by the flame photometer located at the interface after aspirating a sample of the condensed steam through a continuous condensate sampler. The condensate has been degassed throughmore » a condensate-NCG separator. The flame photometer analog signal is then converted by a voltage-to-current converter/transmitter and relayed to the processor which is located at the control center through electrical cable to give a digital sodium concentration read-out at the control panel. The system features a high and high-high sodium level alarm, a continuous strip-chart recorder and a central computer for data capture, retrieval, and processing for further interpretation. Safety devices, such as the flame-off indicator at the control center and the automatic fuel cut-off device along the fuel line, are incorporated in the system.« less

Experiences with industrial solar process steam generation in Jordan

NASA Astrophysics Data System (ADS)

Krüger, Dirk; Berger, Michael; Mokhtar, Marwan; Willwerth, Lisa; Zahler, Christian; Al-Najami, Mahmoud; Hennecke, Klaus

2017-06-01

At the Jordanian pharmaceuticals manufacturing company RAM Pharma a solar process heat supply has been constructed by Industrial Solar GmbH in March 2015 and operated since then (Figure 1). The collector field consists of 394 m² of linear Fresnel collectors supplying saturated steam to the steam network at RAM Pharma at about 6 bar gauge. In the frame of the SolSteam project funded by the German Federal Ministry for Economic Affairs and Energy (BMWi) the installation has been modified introducing an alternative way to separate water and steam by a cyclone. This paper describes the results of experiments with the cyclone and compares the operation with a steam drum. The steam production of the solar plant as well as the fuel demand of the steam boiler are continuously monitored and results are presented in this paper.

40 CFR 60.4340 - How do I demonstrate continuous compliance for NOX if I do not use water or steam injection?

Code of Federal Regulations, 2010 CFR

2010-07-01

... compliance for NOX if I do not use water or steam injection? 60.4340 Section 60.4340 Protection of... NEW STATIONARY SOURCES Standards of Performance for Stationary Combustion Turbines Monitoring § 60.4340 How do I demonstrate continuous compliance for NOX if I do not use water or steam injection? (a...

40 CFR 60.4340 - How do I demonstrate continuous compliance for NOX if I do not use water or steam injection?

Code of Federal Regulations, 2014 CFR

2014-07-01

... compliance for NOX if I do not use water or steam injection? 60.4340 Section 60.4340 Protection of... NEW STATIONARY SOURCES Standards of Performance for Stationary Combustion Turbines Monitoring § 60.4340 How do I demonstrate continuous compliance for NOX if I do not use water or steam injection? (a...

40 CFR 60.4340 - How do I demonstrate continuous compliance for NOX if I do not use water or steam injection?

Code of Federal Regulations, 2011 CFR

2011-07-01

... compliance for NOX if I do not use water or steam injection? 60.4340 Section 60.4340 Protection of... NEW STATIONARY SOURCES Standards of Performance for Stationary Combustion Turbines Monitoring § 60.4340 How do I demonstrate continuous compliance for NOX if I do not use water or steam injection? (a...

40 CFR 60.4340 - How do I demonstrate continuous compliance for NOX if I do not use water or steam injection?

Code of Federal Regulations, 2012 CFR

2012-07-01

... compliance for NOX if I do not use water or steam injection? 60.4340 Section 60.4340 Protection of... NEW STATIONARY SOURCES Standards of Performance for Stationary Combustion Turbines Monitoring § 60.4340 How do I demonstrate continuous compliance for NOX if I do not use water or steam injection? (a...

40 CFR 60.4340 - How do I demonstrate continuous compliance for NOX if I do not use water or steam injection?

Code of Federal Regulations, 2013 CFR

2013-07-01

... compliance for NOX if I do not use water or steam injection? 60.4340 Section 60.4340 Protection of... NEW STATIONARY SOURCES Standards of Performance for Stationary Combustion Turbines Monitoring § 60.4340 How do I demonstrate continuous compliance for NOX if I do not use water or steam injection? (a...

Optical steam quality measurement system and method

DOEpatents

Davidson, James R.; Partin, Judy K.

2006-04-25

An optical measurement system is presented that offers precision on-line monitoring of the quality of steam. Multiple wavelengths of radiant energy are passed through the steam from an emitter to a detector. By comparing the amount of radiant energy absorbed by the flow of steam for each wavelength, a highly accurate measurement of the steam quality can be determined on a continuous basis in real-time. In an embodiment of the present invention, the emitter, comprises three separate radiant energy sources for transmitting specific wavelengths of radiant energy through the steam. In a further embodiment, the wavelengths of radiant energy are combined into a single beam of radiant energy for transmission through the steam using time or wavelength division multiplexing. In yet a further embodiment, the single beam of radiant energy is transmitted using specialized optical elements.

40 CFR 75.39 - Missing data procedures for sorbent trap monitoring systems.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Missing data procedures for sorbent... (CONTINUED) AIR PROGRAMS (CONTINUED) CONTINUOUS EMISSION MONITORING Missing Data Substitution Procedures § 75.39 Missing data procedures for sorbent trap monitoring systems. (a) If a primary sorbent trap...

Monitoring of European corn borer with pheromone-baited traps: review of trapping system basics and remaining problems.

PubMed

Laurent, Pélozuelo; Frérot, Brigitte

2007-12-01

Since the identification of female European corn borer, Ostrinia nubilalis (Hübner) pheromone, pheromone-baited traps have been regarded as a promising tool to monitor populations of this pest. This article reviews the literature produced on this topic since the 1970s. Its aim is to provide extension entomologists and other researchers with all the necessary information to establish an efficient trapping procedure for this moth. The different pheromone races of the European corn borer are described, and research results relating to the optimization of pheromone blend, pheromone bait, trap design, and trap placement are summarized followed by a state-of-the-art summary of data comparing blacklight trap and pheromone-baited trap techniques to monitor European corn borer flight. Finally, we identify the information required to definitively validate/invalidate the pheromone-baited traps as an efficient decision support tool in European corn borer control.

Development and optimization of the Suna trap as a tool for mosquito monitoring and control

PubMed Central

2014-01-01

Background Monitoring of malaria vector populations provides information about disease transmission risk, as well as measures of the effectiveness of vector control. The Suna trap is introduced and evaluated with regard to its potential as a new, standardized, odour-baited tool for mosquito monitoring and control. Methods Dual-choice experiments with female Anopheles gambiae sensu lato in a laboratory room and semi-field enclosure, were used to compare catch rates of odour-baited Suna traps and MM-X traps. The relative performance of the Suna trap, CDC light trap and MM-X trap as monitoring tools was assessed inside a human-occupied experimental hut in a semi-field enclosure. Use of the Suna trap as a tool to prevent mosquito house entry was also evaluated in the semi-field enclosure. The optimal hanging height of Suna traps was determined by placing traps at heights ranging from 15 to 105 cm above ground outside houses in western Kenya. Results In the laboratory the mean proportion of An. gambiae s.l. caught in the Suna trap was 3.2 times greater than the MM-X trap (P < 0.001), but the traps performed equally in semi-field conditions (P = 0.615). As a monitoring tool , the Suna trap outperformed an unlit CDC light trap (P < 0.001), but trap performance was equal when the CDC light trap was illuminated (P = 0.127). Suspending a Suna trap outside an experimental hut reduced entry rates by 32.8% (P < 0.001). Under field conditions, suspending the trap at 30 cm above ground resulted in the greatest catch sizes (mean 25.8 An. gambiae s.l. per trap night). Conclusions The performance of the Suna trap equals that of the CDC light trap and MM-X trap when used to sample An. gambiae inside a human-occupied house under semi-field conditions. The trap is effective in sampling mosquitoes outside houses in the field, and the use of a synthetic blend of attractants negates the requirement of a human bait. Hanging a Suna trap outside a house can reduce An. gambiae house entry and its use as a novel tool for reducing malaria transmission risk will be evaluated in peri-domestic settings in sub-Saharan Africa. PMID:24998771

Sediment traps for measuring onslope surface sediment movement

Treesearch

Wade G. Wells; Peter M. Wohlgemuth

1987-01-01

Two types of small (30-cm aperture) sheet metal sediment traps were developed to monitor onslope surface sediment transport. Traditionally, sediment traps and erosion pins have been used to measure the onslope movement of surficial soil material. While pins may be appropriate for documenting landscape denudation, traps are more suitable for monitoring downslope...

Plastic cup traps equipped with light-emitting diodes for monitoring adult Bemisia tabaci (Homoptera: Aleyrodidae).

PubMed

Chu, Chang-Chi; Jackson, Charles G; Alexander, Patrick J; Karut, Kamil; Henneberry, Thomas J

2003-06-01

Equipping the standard plastic cup trap, also known as the CC trap, with lime-green light-emitting diodes (LED-plastic cup trap) increased its efficacy for catching Bemisia tabaci by 100%. Few Eretmocerus eremicus Rose and Zolnerowich and Encarsia formosa Gahan were caught in LED-plastic cup traps. The LED-plastic cup traps are less expensive than yellow sticky card traps for monitoring adult whiteflies in greenhouse crop production systems and are more compatible with whitefly parasitoids releases for Bemisia nymph control.

Current techniques in acid-chloride corrosion control and monitoring at The Geysers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hirtz, Paul; Buck, Cliff; Kunzman, Russell

1991-01-01

Acid chloride corrosion of geothermal well casings, production piping and power plant equipment has resulted in costly corrosion damage, frequent curtailments of power plants and the permanent shut-in of wells in certain areas of The Geysers. Techniques have been developed to mitigate these corrosion problems, allowing continued production of steam from high chloride wells with minimal impact on production and power generation facilities.The optimization of water and caustic steam scrubbing, steam/liquid separation and process fluid chemistry has led to effective and reliable corrosion mitigation systems currently in routine use at The Geysers. When properly operated, these systems can yield steammore » purities equal to or greater than those encountered in areas of The Geysers where chloride corrosion is not a problem. Developments in corrosion monitoring techniques, steam sampling and analytical methodologies for trace impurities, and computer modeling of the fluid chemistry has been instrumental in the success of this technology.« less

A pheromone-baited trap for monitoring the Indian meal moth, Plodia interpunctella (Hübner) (Lepidoptera: Pyralidae).

PubMed

Mullen, M A.; Dowdy, A K.

2001-07-01

A pheromone-baited trap was developed to monitor the Indian meal moth in grocery stores and similar areas where visible traps are not desirable. The trap can be used under shelves and against walls. As a shelf mount, the trap is in close proximity to the food packages and may capture emerging insects before they mate. The trap can also be used as a hanging trap similar to the Pherocon II. When used as a shelf or wall mount, it was as effective as the Pherocon II, but when used as a hanging trap significantly fewer insects were captured.

On line instrument systems for monitoring steam turbogenerators

NASA Astrophysics Data System (ADS)

Clapis, A.; Giorgetti, G.; Lapini, G. L.; Benanti, A.; Frigeri, C.; Gadda, E.; Mantino, E.

A computerized real time data acquisition and data processing for the diagnosis of malfunctioning of steam turbogenerator systems is described. Pressure, vibration and temperature measurements are continuously collected from standard or special sensors including startup or stop events. The architecture of the monitoring system is detailed. Examples of the graphics output are presented. It is shown that such a system allows accurate diagnosis and the possibility of creating a data bank to describe the dynamic characteristics of the machine park.

Monitoring oriental fruit moth (Lepidoptera: Tortricidae) with sticky traps baited with terpinyl acetate and sex pheromone

USDA-ARS?s Scientific Manuscript database

Studies in Argentina and Chile during 2010-11 evaluated a new trap (Ajar) for monitoring the oriental fruit moth, Grapholita molesta (Busck). The Ajar trap was delta-shaped with a jar filled with a terpinyl acetate plus brown sugar bait attached to the bottom center of the trap. The screened lid of ...

Effectiveness of bed bug monitors for detecting and trapping bed bugs in apartments.

PubMed

Wang, Changlu; Tsai, Wan-Tien; Cooper, Richard; White, Jeffrey

2011-02-01

Bed bugs, Cimex lectularius L., are now considered a serious urban pest in the United States. Because they are small and difficult to find, there has been strong interest in developing and using monitoring tools to detect bed bugs and evaluate the results of bed bug control efforts. Several bed bug monitoring devices were developed recently, but their effectiveness is unknown. We comparatively evaluated three active monitors that contain attractants: CDC3000, NightWatch, and a home-made dry ice trap. The Climbup Insect Interceptor, a passive monitor (without attractants), was used for estimating the bed bug numbers before and after placing active monitors. The results of the Interceptors also were compared with the results of the active monitors. In occupied apartments, the relative effectiveness of the active monitors was: dry ice trap > CDC3000 > NightWatch. In lightly infested apartments, the Interceptor (operated for 7 d) trapped similar number of bed bugs as the dry ice trap (operated for 1 d) and trapped more bed bugs than CDC3000 and NightWatch (operated for 1 d). The Interceptor was also more effective than visual inspections in detecting the presence of small numbers of bed bugs. CDC3000 and the dry ice trap operated for 1 d were equally as effective as the visual inspections for detecting very low level of infestations, whereas 1-d deployment of NightWatch detected significantly lower number of infestations compared with visual inspections. NightWatch was designed to be able to operate for several consecutive nights. When operated for four nights, NightWatch trapped similar number of bed bugs as the Interceptors operated for 10 d after deployment of NightWatch. We conclude these monitors are effective tools in detecting early bed bug infestations and evaluating the results of bed bug control programs.

Study of water dynamics in the soaking, steaming, and solid-state fermentation of glutinous rice by LF-NMR: a novel monitoring approach.

PubMed

Li, Teng; Tu, Chuanhai; Rui, Xin; Gao, Yangwen; Li, Wei; Wang, Kun; Xiao, Yu; Dong, Mingsheng

2015-04-01

Solid-state fermentation (SSF) of starchy grain is a traditional technique for food and alcoholic beverage production in East Asia. In the present study, low-field nuclear magnetic resonance (LF-NMR) was introduced for the elucidation of water dynamics and microstructure alternations during the soaking, steaming, and SSF of glutinous rice as a rapid real-time monitoring method. Three different proton fractions with different mobilities were identified based on the degree of interaction between biopolymers and water. Soaking and steaming significantly changed the proton distribution of the sample. The different phases of SSF were reflected by the T2 parameters. In addition, the variations in the T2 parameters were explained by the microstructure changes of rice induced by SSF. The fermentation time and T2 parameters were sigmoidally correlated. Thus, LF-NMR may be an effective real-time monitoring method for SSF in starch systems.

Captures of Boll Weevils (Coleoptera: Curculionidae) in Relation to Trap Distance From Cotton Fields.

PubMed

Spurgeon, Dale W

2016-12-01

The boll weevil (Anthonomus grandis grandis Boheman) has been eradicated from much of the United States, but remains an important pest of cotton (Gossypium spp.) in other parts of the Americas. Where the weevil occurs, the pheromone trap is a key tool for population monitoring or detection. Traditional monitoring programs have placed traps in or near the outermost cotton rows where damage by farm equipment can cause loss of trapping data. Recently, some programs have adopted a trap placement adjacent to but outside monitored fields. The effects of these changes have not been previously reported. Captures of early-season boll weevils by traps near (≤1 m) or far (7-10 m) from the outermost cotton row were evaluated. In 2005, during renewed efforts to eradicate the boll weevil from the Lower Rio Grande Valley of Texas, far traps consistently captured more weevils than traps near cotton. Traps at both placements indicated similar patterns of early-season weevil captures, which were consistent with those previously reported. In 2006, no distinction between trap placements was detected. Early-season patterns of captures in 2006 were again similar for both trap placements, but captures were much lower and less regular compared with those observed in 2005. These results suggest magnitude and likelihood of weevil capture in traps placed away from cotton are at least as high as for traps adjacent to cotton. Therefore, relocation of traps away from the outer rows of cotton should not negatively impact ability to monitor or detect the boll weevil. Published by Oxford University Press on behalf of Entomological Society of America 2016. This work is written by a US Government employee and is in the public domain in the US.

Procedure 5 Quality Assurance Requirements For Vapor Phase Mercury Continuous Emissions Monitoring Systems And Sorbent Trap Monitoring Systems Used For Compliance Determination At Stationary Sources

EPA Pesticide Factsheets

Promulgated quality assurance Procedure 5 Quality Assurance Requirements For Vapor Phase Mercury Continuous Emissions Monitoring Systems And Sorbent Trap Monitoring Systems Used For Compliance Determination At Stationary Sources

Comparison of Trap Types, Placement, and Colors for Monitoring Anthonomus musculus (Coleoptera: Curculionidae) Adults in Highbush Blueberries

PubMed Central

Silva, Diego; Salamanca, Jordano; Kyryczenko-Roth, Vera; Alborn, Hans T; Rodriguez-Saona, Cesar

2018-01-01

Abstract The cranberry weevil, Anthonomus musculus Say (Coleoptera: Curculionidae), is a key (univoltine) pest of highbush blueberries in the northeast United States. To date, however, no trapping system has been developed to successfully monitor this pest. In 2012–2014, studies were conducted in commercial highbush blueberry farms in New Jersey to 1) evaluate the efficacy of various commercially available traps, designed for other weevil species (e.g., pepper weevil, plum curculio, boll weevil, red palm weevil, and black vine weevil), in capturing A. musculus adults; 2) test whether the relative location of traps within the blueberry canopy affects adult captures and 3) determine the effects of different colored (yellow, white, green, red, blue, brown, and black) sticky traps on weevil captures. For a comparison with existing techniques, we also monitored the number of overwintered adult weevils on blueberry bushes using beat sheet sampling. Of all traps and colors tested, the most A. musculus adults were caught on yellow sticky traps and more adults were captured when these traps were placed at the bottom half of the blueberry canopy, i.e., 0.5–1.0 m above ground. Most weevils were caught on colored traps late in the season (i.e., during bloom), which corresponds mostly to the second (summer) adult generation. Thus, number of overwintered adults caught on traps did not correlate with those on bushes. Although our study identified traps that can be used to capture A. musculus adults, these traps alone (i.e., without semiochemicals) have so far limited applicability for monitoring overwintered adult weevils in highbush blueberries.

Development of a Low-Cost and Effective Trapping Device for Apple Maggot Fly (Diptera: Tephritidae) Monitoring and Control in Mexican Commercial Hawthorn Groves.

PubMed

Tadeo, E; Muñiz, E; Rull, J; Yee, W L; Aluja, M; Lasa, R

2017-08-01

Few efforts have been made in Mexico to monitor Rhagoletis pomonella (Walsh) (Diptera: Tephritidae) in commercial hawthorn (Crataegus spp.) crops. Therefore, the main objectives of this study were to evaluate infestation levels of R. pomonella in feral and commercial Mexican hawthorn and to assess the efficacy of different trap-lure combinations to monitor the pest. Wild hawthorn was more infested than commercially grown hawthorn at the sample site. No differences among four commercial baits (Biolure, ammonium carbonate, CeraTrap, and Captor + borax) were detected when used in combination with a yellow sticky gel (SG) adherent trap under field conditions. However, liquid lures elicited a slightly higher, although not statistically different, capture. Cage experiments in the laboratory revealed that flies tended to land more often on the upper and middle than lower-bottom part of polyethylene (PET) bottle traps with color circles. Among red, orange, green, and yellow circles attached to a bottle trap, only yellow circles improved fly captures compared with a colorless trap. A PET bottle trap with a red circle over a yellow background captured more flies than a similar trap with yellow circles. An SG adherent yellow panel trap baited with ammonium carbonate was superior to the improved PET bottle trap (red over a yellow background) baited with different liquid proteins, but a higher proportion of females and no differences in fly detection were measured in PET traps baited with protein lures. These trials open the door for future research into development of a conventional nonadherent trap to monitor or control R. pomonella. © The Authors 2017. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Halyomorpha halys (Hemiptera: Pentatomidae) response to pyramid traps baited with attractive light and pheromonal stimuli

USDA-ARS?s Scientific Manuscript database

Halyomorpha halys is an invasive insect that causes severe economic damage to multiple agricultural commodities. Several monitoring techniques have been developed to monitor H. halys including pheromone and light-baited black pyramid traps. Here, we evaluated the attractiveness of these traps bait...

The Monitoring System of the Operating State of the Gear Wheels of the Torque Multiplier of the Desalination Plant Steam Generator

NASA Astrophysics Data System (ADS)

Danilin, A. I.; Neverov, V. V.; Danilin, S. A.; Shimanov, A. A.; Tsapkova, A. B.

2018-01-01

The article describes a noncontact operational control method based on the processing of a microwave signal reflected from the controlled teeth of the wheel. In this paper describes the influence of wear patterns on the characteristic information parameters of the analyzed signals. The block diagram in section 3 shows the experimental system for monitoring the operating state of the gear wheels of the steam compressor torque multiplier. The design of the primary converter is briefly described.

40 CFR Table 3 to Subpart Ooo of... - Batch Process Vent Monitoring Requirements

Code of Federal Regulations, 2013 CFR

2013-07-01

...) temperature Continuous records as specified in § 63.1416(d). a Carbon adsorber a Total regeneration steam flow or nitrogen flow, or pressure (gauge or absolute) during carbon bed regeneration cycle(s), and Record the total regeneration steam flow or nitrogen flow, or pressure for each carbon bed regeneration cycle...

40 CFR Table 3 to Subpart Ooo of... - Batch Process Vent Monitoring Requirements

Code of Federal Regulations, 2014 CFR

2014-07-01

...) temperature Continuous records as specified in § 63.1416(d). a Carbon adsorber a Total regeneration steam flow or nitrogen flow, or pressure (gauge or absolute) during carbon bed regeneration cycle(s), and Record the total regeneration steam flow or nitrogen flow, or pressure for each carbon bed regeneration cycle...

Can camera traps monitor Komodo dragons a large ectothermic predator?

PubMed

Ariefiandy, Achmad; Purwandana, Deni; Seno, Aganto; Ciofi, Claudio; Jessop, Tim S

2013-01-01

Camera trapping has greatly enhanced population monitoring of often cryptic and low abundance apex carnivores. Effectiveness of passive infrared camera trapping, and ultimately population monitoring, relies on temperature mediated differences between the animal and its ambient environment to ensure good camera detection. In ectothermic predators such as large varanid lizards, this criterion is presumed less certain. Here we evaluated the effectiveness of camera trapping to potentially monitor the population status of the Komodo dragon (Varanus komodoensis), an apex predator, using site occupancy approaches. We compared site-specific estimates of site occupancy and detection derived using camera traps and cage traps at 181 trapping locations established across six sites on four islands within Komodo National Park, Eastern Indonesia. Detection and site occupancy at each site were estimated using eight competing models that considered site-specific variation in occupancy (ψ)and varied detection probabilities (p) according to detection method, site and survey number using a single season site occupancy modelling approach. The most parsimonious model [ψ (site), p (site survey); ω = 0.74] suggested that site occupancy estimates differed among sites. Detection probability varied as an interaction between site and survey number. Our results indicate that overall camera traps produced similar estimates of detection and site occupancy to cage traps, irrespective of being paired, or unpaired, with cage traps. Whilst one site showed some evidence detection was affected by trapping method detection was too low to produce an accurate occupancy estimate. Overall, as camera trapping is logistically more feasible it may provide, with further validation, an alternative method for evaluating long-term site occupancy patterns in Komodo dragons, and potentially other large reptiles, aiding conservation of this species.

Can Camera Traps Monitor Komodo Dragons a Large Ectothermic Predator?

PubMed Central

Ariefiandy, Achmad; Purwandana, Deni; Seno, Aganto; Ciofi, Claudio; Jessop, Tim S.

2013-01-01

Camera trapping has greatly enhanced population monitoring of often cryptic and low abundance apex carnivores. Effectiveness of passive infrared camera trapping, and ultimately population monitoring, relies on temperature mediated differences between the animal and its ambient environment to ensure good camera detection. In ectothermic predators such as large varanid lizards, this criterion is presumed less certain. Here we evaluated the effectiveness of camera trapping to potentially monitor the population status of the Komodo dragon (Varanus komodoensis), an apex predator, using site occupancy approaches. We compared site-specific estimates of site occupancy and detection derived using camera traps and cage traps at 181 trapping locations established across six sites on four islands within Komodo National Park, Eastern Indonesia. Detection and site occupancy at each site were estimated using eight competing models that considered site-specific variation in occupancy (ψ)and varied detection probabilities (p) according to detection method, site and survey number using a single season site occupancy modelling approach. The most parsimonious model [ψ (site), p (site*survey); ω = 0.74] suggested that site occupancy estimates differed among sites. Detection probability varied as an interaction between site and survey number. Our results indicate that overall camera traps produced similar estimates of detection and site occupancy to cage traps, irrespective of being paired, or unpaired, with cage traps. Whilst one site showed some evidence detection was affected by trapping method detection was too low to produce an accurate occupancy estimate. Overall, as camera trapping is logistically more feasible it may provide, with further validation, an alternative method for evaluating long-term site occupancy patterns in Komodo dragons, and potentially other large reptiles, aiding conservation of this species. PMID:23527027

Fiber optic strain and temperature sensor for power plant applications

NASA Astrophysics Data System (ADS)

Narendran, Nadarajah; Weiss, Joseph M.

1996-01-01

The applicability of fiber-optic strain and temperature sensors to monitor power plant structures was evaluated on a super-heated steam pipe operating at 1000 degree(s)F at the Tennessee Valley Authority power plant in Kingston, Tennessee. The potential applications of these fiber-optic sensors include health monitoring of high-temperature structures such as boilers, tube headers, and steam pipes, as well as many other power plant structures exposed to less severe environments. The sensor selected for this application is based on a white-light interferometric technique. The key features of this sensor include its ability for absolute measurements that are not affected by light loss along the fiber cable due to, for example, microbending effects and coupler loss, its compatibility with off-the-shelf fiber-optic components, and its low cost. The glass fiber-optic strain sensors were packaged in a rugged metal housing and were spot welded to the high-temperature steam pipe. Another set of gages was placed inside a thermowell for steam temperature measurement. Data collected during a routine start-up is very encouraging and the details are presented in this manuscript.

Line-Trapping of Codling Moth (Lepidoptera: Tortricidae): A Novel Approach to Improving the Precision of Capture Numbers in Traps Monitoring Pest Density.

PubMed

Adams, C G; McGhee, P S; Schenker, J H; Gut, L J; Miller, J R

2017-08-01

This field study of codling moth, Cydia pomonella (L.), response to single versus multiple monitoring traps baited with codlemone demonstrates that precision of a given capture number is alarmingly poor when the population is held constant by releasing moths. Captures as low as zero and as high as 12 males per single trap are to be expected where the catch mode is three. Here, we demonstrate that the frequency of false negatives and overestimated positives for codling moth trapping can be substantially reduced by employing the tactic of line-trapping, where five traps were deployed 4 m apart along a row of apple trees. Codling moth traps spaced closely competed only slightly. Therefore, deploying five traps closely in a line is a sampling technique nearly as good as deploying five traps spaced widely. But line trapping offers a substantial savings in time and therefore cost when servicing aggregated versus distributed traps. As the science of pest management matures by mastering the ability to translate capture numbers into estimates of absolute pest density, it will be important to employ a tactic like line-trapping so as to shrink the troublesome variability associated with capture numbers in single traps that thwarts accurate decisions about if and when to spray. Line-trapping might similarly increase the reliability and utility of density estimates derived from capture numbers in monitoring traps for various pest and beneficial insects. © The Authors 2017. Published by Oxford University Press on behalf of Entomological Society of America.

40 CFR 60.4355 - How do I establish and document a proper parameter monitoring plan?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Standards of Performance for Stationary Combustion Turbines Monitoring § 60.4355 How do I establish and document a proper parameter monitoring plan? (a) The steam or water to fuel ratio or other parameters that...

Characterization of gas chemistry and noble-gas isotope ratios of inclusion fluids in magmatic-hydrothermal and magmatic-steam alunite

USGS Publications Warehouse

Landis, G.P.; Rye, R.O.

2005-01-01

Chemical and isotope data were obtained for the active gas and noble gas of inclusion fluids in coarse-grained samples of magmatic-hydrothermal and magmatic-steam alunite from well-studied deposits (Marysvale, Utah; Tambo, Chile; Tapajo??s, Brazil; Cactus, California; Pierina, Peru), most of which are discussed in this Volume. Primary fluid inclusions in the alunite typically are less than 0.2 ??m but range up to several micrometers. Analyses of the active-gas composition of these alunite-hosted inclusion fluids released in vacuo by both crushing and heating indicate consistent differences in the compositions of magmatic-hydrothermal and magmatic-steam fluids. The compositions of fluids released by crushing were influenced by contributions from significant populations of secondary inclusions that trapped largely postdepositional hydrothermal fluids. Thermally released fluids gave the best representation of the fluids that formed primary alunite. The data are consistent with current models for the evolution of magmatic-hydrothermal and magmatic-steam fluids. Magmatic-steam fluids are vapor-dominant, average about 49 mol% H2O, and contain N2, H2, CH4, CO, Ar, He, HF, and HCl, with SO2 the dominant sulfur gas (average SO2/ H2S=202). In contrast, magmatic-hydrothermal fluids are liquid-dominant, average about 88 mol% H2O, and N2, H2, CO2, and HF, with H2S about as abundant as SO2 (average SO2/H2 S=0.7). The low SO2/H2S and N2/Ar ratios, and the near-absence of He in magmatic-hydrothermal fluids, are consistent with their derivation from degassed condensed magmatic fluids whose evolution from reduced-to-oxidized aqueous sulfur species was governed first by rock and then by fluid buffers. The high SO2/H2S and N2/Ar with significant concentrations of He in magmatic-steam fluids are consistent with derivation directly from a magma. None of the data supports the entrainment of atmospheric gases or mixing of air-saturated gases in meteoric water in either magmatic-hydrothermal or magmatic-steam fluids. Thus, the oxidation of SO2 to aqueous sulfate in the magmatic-steam fluids did not result from mixing with atmospheric oxygen. Both of the fluid types are characterized by high H2 contents that range from 0.2 mol% to the extraordinarily large amounts (66 mol%) observed in some magmatic-steam fluids. Modeling of gas speciation using SOLVGAS requires most of the gas species to have been in disequilibrium at the time of their trapping in the fluid inclusions. The origin of such extreme H2 concentrations, although problematic, is thought to be largely related to accumulation of H2 from the reaction of water with ferrous iron during the rise of magma and probably even after exsolution of fluid from a magma. The large contents of reduced gases in the inclusion fluids are far in excess of those observed in volcanic emanations, and are thought to reflect the close "sampling position" of the host alunite relative to the location of the magma. Isotope ratios of He and Ne indicate largely crustal sources for these gases in the alunite parental fluids derived from Tertiary magmas, but a greater mantle component for the gases in alunite parental fluids derived from Proterozoic magmas.

A model for internal oscillations in geysers, with application to Old Faithful (Yellowstone, USA)

NASA Astrophysics Data System (ADS)

Rudolph, Maxwell L.; Sohn, Robert A.

2017-09-01

We present a mechanical model for internal oscillations in geysers with "bubble trap" configurations, where ascending gas or vapor becomes trapped beneath the roof of a cavity that is laterally offset from the eruption conduit. We consider two cases, one in which the trapped gas behaves as an isothermal ideal gas, and one where it is treated as isenthalpic steam. In both cases the system behaves as a damped, harmonic oscillator with a resonant frequency that is sensitive to the conduit geometries and fluid volumes. We use the model to predict internal oscillation frequencies for Old Faithful geyser, in Yellowstone, USA, using conduit geometry constraints from the literature, and find that the frequencies predicted by the model are consistent with observations ( 1 Hz). We show that systematic frequency increases during the recharge cycle, when the fluid volume of the system is increasing due to recharge, are consistent with either a decrease in the amount (both volume and mass) of trapped gas or vapor, a decrease in the eruption conduit area, or a combination of both.

40 CFR 63.453 - Monitoring requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... process wastewater feed rate; (2) The steam feed rate; and (3) The process wastewater column feed...: (A) Composite daily sample of outlet soluble BOD5 concentration to monitor for maximum daily and...

40 CFR 63.453 - Monitoring requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... process wastewater feed rate; (2) The steam feed rate; and (3) The process wastewater column feed...: (A) Composite daily sample of outlet soluble BOD5 concentration to monitor for maximum daily and...

40 CFR 63.453 - Monitoring requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... process wastewater feed rate; (2) The steam feed rate; and (3) The process wastewater column feed...: (A) Composite daily sample of outlet soluble BOD5 concentration to monitor for maximum daily and...

Field evaluation of four widely used mosquito traps in Central Europe

PubMed Central

2014-01-01

Background To monitor adult mosquitoes several trapping devices are available. These are differently constructed and use various mechanisms for mosquito attraction, thus resulting in different trapping sensitivities and efficacies for the various species. Mosquito monitoring and surveillance programs in Europe use various types of mosquito traps, but only a few comparisons have been conducted so far. This study compared the performance of four commercial trapping devices, which are commonly used in Europe. Methods Four different traps, Biogents Sentinel trap (BG trap), Heavy Duty Encephalitis Vector Survey trap (EVS trap), Centres for Disease Control miniature light trap (CDC trap) and Mosquito Magnet Patriot Mosquito trap (MM trap) were compared in a 4 × 4 latin square study. In the years 2012 and 2013, more than seventy 24-hour trap comparisons were conducted at ten different locations in northern and southern Germany, representing urban, forest and floodplain biotopes. Results Per 24-hour trapping period, the BG trap caught the widest range of mosquito species, the highest number of individuals of the genus Culex as well as the highest number of individuals of the species Ochlerotatus cantans, Aedes cinereus/geminus, Oc. communis and Culex pipiens/torrentium. The CDC trap revealed best performance for Aedes vexans, whereas the MM trap was most efficient for mosquitoes of the genus Anopheles and the species Oc. geniculatus. The EVS trap did not catch more individuals of any genus or species compared to the other three trapping devices. The BG trap caught the highest number of individuals per trapping period in urban environments as well as in wet forest, while the CDC trap caught the highest number of individuals in the floodplain biotopes. Additionally, the BG trap was most efficient for the number of mosquito species in urban locations. Conclusion The BG trap showed a significantly better or similar performance compared to the CDC, EVS or MM trap with regard to trapping efficacy for most common mosquito species in Germany, including diversity of mosquito species and number of mosquitoes per trapping period. Thus, the BG trap is probably the best solution for general monitoring or surveillance programs of adult mosquitoes in Central Europe. PMID:24924481

A partial pressure monitor and controller for stable ozone flow from a silica gel trap

NASA Astrophysics Data System (ADS)

Stevens, R. E.; Hsiao, C.-W.; Le, Linh; Curro, N. J.; Monton, B. J.; Chang, B.-Y.; Kung, C.-Y.; Kittrell, C.; Kinsey, J. L.

1998-06-01

A new ozone trapping system designed for safe and consistent delivery to a reaction vessel is described. Silica gel is used to trap the ozone because of its known safety advantages over traps that store ozone in liquid form. The new design is free of any liquid baths, such as freon or flammable solvents. A circuit design for monitoring and controlling the ozone partial pressure of 6-25 Torr is also described.

In-Service Monitoring of Steam Pipe Systems at High Temperatures

NASA Technical Reports Server (NTRS)

Bar-Cohen, Yoseph; Lih, Shyh-Shiuh; Badescu, Mircea; Bao, Xiaoqi; Sherrit, Stewart; Scott, James S.; Blosiu, Julian O.; Widholm, Scott E.

2011-01-01

An effective, in-service health monitoring system is needed to track water condensation in real time through the walls of steam pipes. The system is required to measure the height of the condensed water from outside the pipe, while operating at temperatures that are as high as 250 C. The system needs to account for the effects of water flow and cavitation. In addition, it is desired that the system does not require perforating the pipes and thereby reducing the structural integrity. Generally, steam pipes are used as part of the district heating system carrying steam from central power stations under the streets to heat, cool, or supply power to high-rise buildings and businesses. This system uses ultrasonic waves in pulse-echo and acquires reflected signal data. Via autocorrelation, it determines the water height while eliminating the effect of noise and multiple reflections from the wall of the pipe. The system performs nondestructive monitoring through the walls of steam pipes, and automatically measures the height of condensed water while operating at the high-temperature conditions of 250 C. For this purpose, the ultrasonic pulse-echo method is used where the time-of-flight of the wave reflections inside the water are measured, and it is multiplied by the wave velocity to determine the height. The pulse-echo test consists of emitting ultrasonic wave pulses from a piezoelectric transducer and receiving the reflections from the top and bottom of the condensed water. A single transducer is used as a transmitter as well as the receiver of the ultrasonic waves. To obtain high resolution, a broadband transducer is used and the frequency can be in the range of 2.25 to 10 MHz, providing sharp pulses in the time domain allowing for higher resolution in identifying the individual reflections.

40 CFR 63.7500 - What emission limitations, work practice standards, and operating limits must I meet?

Code of Federal Regulations, 2014 CFR

2014-07-01

... pounds per million Btu of steam output, in Tables 1 or 2 to this subpart are an alternative applicable only to boilers and process heaters that generate steam. The output-based emission limits, in units of..., monitoring results, review of operation and maintenance procedures, review of operation and maintenance...

40 CFR 63.7500 - What emission limitations, work practice standards, and operating limits must I meet?

Code of Federal Regulations, 2013 CFR

2013-07-01

... pounds per million Btu of steam output, in Tables 1 or 2 to this subpart are an alternative applicable only to boilers and process heaters that generate steam. The output-based emission limits, in units of..., monitoring results, review of operation and maintenance procedures, review of operation and maintenance...

40 CFR Table 3 to Subpart Ooo of... - Batch Process Vent Monitoring Requirements

Code of Federal Regulations, 2012 CFR

2012-07-01

... specified in § 63.1416(d). a Carbon adsorber a Total regeneration steam flow or nitrogen flow, or pressure (gauge or absolute) during carbon bed regeneration cycle(s), and Record the total regeneration steam flow or nitrogen flow, or pressure for each carbon bed regeneration cycle. Temperature of the carbon bed...

40 CFR Table 3 to Subpart Ooo of... - Batch Process Vent Monitoring Requirements

Code of Federal Regulations, 2010 CFR

2010-07-01

... specified in § 63.1416(d). a Carbon adsorber a Total regeneration steam flow or nitrogen flow, or pressure (gauge or absolute) during carbon bed regeneration cycle(s), and Record the total regeneration steam flow or nitrogen flow, or pressure for each carbon bed regeneration cycle. Temperature of the carbon bed...

40 CFR Table 3 to Subpart Ooo of... - Batch Process Vent Monitoring Requirements

Code of Federal Regulations, 2011 CFR

2011-07-01

... specified in § 63.1416(d). a Carbon adsorber a Total regeneration steam flow or nitrogen flow, or pressure (gauge or absolute) during carbon bed regeneration cycle(s), and Record the total regeneration steam flow or nitrogen flow, or pressure for each carbon bed regeneration cycle. Temperature of the carbon bed...

40 CFR 52.1170 - Identification of plan.

Code of Federal Regulations, 2014 CFR

2014-07-01

... compounds form existing automobile, truck, and business machine plastic part coating lines 4/27/93 9/7/94... Continuous emission monitoring, fossil fuel-fired steam generators 3/19/02 6/1/06, 71 FR 31093 R 336.2102... 336.2175 Data reduction procedures for fossil fuel-fired steam generators 11/15/04 6/1/06, 71 FR 31093...

40 CFR 52.1170 - Identification of plan.

Code of Federal Regulations, 2011 CFR

2011-07-01

... compounds form existing automobile, truck, and business machine plastic part coating lines 4/27/93 9/7/94... Continuous emission monitoring, fossil fuel-fired steam generators 3/19/02 6/1/06, 71 FR 31093 R 336.2102... 336.2175 Data reduction procedures for fossil fuel-fired steam generators 11/15/04 6/1/06, 71 FR 31093...

40 CFR 52.1170 - Identification of plan.

Code of Federal Regulations, 2012 CFR

2012-07-01

... compounds form existing automobile, truck, and business machine plastic part coating lines 4/27/93 9/7/94... Continuous emission monitoring, fossil fuel-fired steam generators 3/19/02 6/1/06, 71 FR 31093 R 336.2102... 336.2175 Data reduction procedures for fossil fuel-fired steam generators 11/15/04 6/1/06, 71 FR 31093...

40 CFR 52.1170 - Identification of plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... compounds form existing automobile, truck, and business machine plastic part coating lines 4/27/93 9/7/94... Continuous emission monitoring, fossil fuel-fired steam generators 3/19/02 6/1/06, 71 FR 31093 R 336.2102... 336.2175 Data reduction procedures for fossil fuel-fired steam generators 11/15/04 6/1/06, 71 FR 31093...

40 CFR 52.1170 - Identification of plan.

Code of Federal Regulations, 2013 CFR

2013-07-01

... compounds form existing automobile, truck, and business machine plastic part coating lines 4/27/93 9/7/94... Continuous emission monitoring, fossil fuel-fired steam generators 3/19/02 6/1/06, 71 FR 31093 R 336.2102... 336.2175 Data reduction procedures for fossil fuel-fired steam generators 11/15/04 6/1/06, 71 FR 31093...

Laboratory investigations of the physics of steam flow in a porous medium

USGS Publications Warehouse

Herkelrath, W.N.; Moench, A.F.

1982-01-01

Experiments were carried out in the laboratory to test a theory of transient flow of pure steam in a uniform porous medium. This theory is used extensively in modeling pressure-transient behavior in vapor-dominated geothermal systems. Transient, superheated steam-flow experiments were run by bringing a cylinder of porous material to a uniform initial pressure, and then making a step increase in pressure at one end of the sample, while monitoring the pressure-transient breakthrough at the other end. It was found in experiments run at 100?, 125?, and 146?C that the time required for steam-pressure transients to propagate through an unconsolidated material containing sand, silt, and clay was 10 to 25 times longer than predicted by theory. It is hypothesized that the delay in the steam-pressure transient was caused by adsorption of steam in the porous sample. In order to account for steam adsorption, a sink term was included in the conservation of mass equation. In addition, energy transfer in the system has to be considered because latent heat is released when steam adsorption occurs, increasing the sample temperature by as much as 10?C. Finally, it was recognized that the steam pressure was a function of both the temperature and the amount of adsorption in the sample. For simplicity, this function was assumed to be in equilibrium adsorption isotherm, which was determined by experiment. By solving the modified mass and energy equations numerically, subject to the empirical adsorption isotherm relationship, excellent theoretical simulation of the experiments was achieved. The experiments support the hypothesis that adsorption of steam can strongly influence steam pressure-transient behavior in porous media; the results suggest that the modified steam-flow theory, which includes steam adsorption terms, should be used in modeling steam flow in vapor-dominated geothermal systems.

Comparative analysis of three different methods for monitoring the use of green bridges by wildlife.

PubMed

Gužvica, Goran; Bošnjak, Ivana; Bielen, Ana; Babić, Danijel; Radanović-Gužvica, Biserka; Šver, Lidija

2014-01-01

Green bridges are used to decrease highly negative impact of roads/highways on wildlife populations and their effectiveness is evaluated by various monitoring methods. Based on the 3-year monitoring of four Croatian green bridges, we compared the effectiveness of three indirect monitoring methods: track-pads, camera traps and active infrared (IR) trail monitoring system. The ability of the methods to detect different species and to give good estimation of number of animal crossings was analyzed. The accuracy of species detection by track-pad method was influenced by granulometric composition of track-pad material, with the best results obtained with higher percentage of silt and clay. We compared the species composition determined by track-pad and camera trap methods and found that monitoring by tracks underestimated the ratio of small canids, while camera traps underestimated the ratio of roe deer. Regarding total number of recorder events, active IR detectors recorded from 11 to 19 times more events then camera traps and app. 80% of them were not caused by animal crossings. Camera trap method underestimated the real number of total events. Therefore, an algorithm for filtration of the IR dataset was developed for approximation of the real number of crossings. Presented results are valuable for future monitoring of wildlife crossings in Croatia and elsewhere, since advantages and disadvantages of used monitoring methods are shown. In conclusion, different methods should be chosen/combined depending on the aims of the particular monitoring study.

Measurement of the Neutron Lifetime with Ultra-cold Neutrons Stored in a Magneto-gravitational Trap

NASA Astrophysics Data System (ADS)

Ezhov, V. F.; Andreev, A. Z.; Ban, G.; Bazarov, B. A.; Geltenbort, P.; Glushkov, A. G.; Knyazkov, V. A.; Kovrizhnykh, N. A.; Krygin, G. B.; Naviliat-Cuncic, O.; Ryabov, V. L.

2018-05-01

We report a measurement of the neutron lifetime using ultra-cold neutrons stored in a magneto-gravitational trap made of permanent magnets. Neutrons surviving in the trap after fixed storage times have been counted and the trap losses have continuously been monitored during storage by detecting neutrons leaking from the trap. The value of the neutron lifetime resulting from this measurement is τ n = (878.3 ± 1.6stat ± 1.0syst) s. A unique feature of this experiment is the monitoring of leaking neutrons providing a robust control of the main systematic loss.

The relationship between surface temperature, tissue temperature, microbubble formation, and steam pops.

PubMed

Thompson, Nathaniel; Lustgarten, Daniel; Mason, Bryan; Mueller, Enkhtuyaa; Calame, James; Bell, Stephen; Spector, Peter

2009-07-01

It has been proposed that microbubble (MB) monitoring can be used to safely titrate radiofrequency (RF) power. However, MB formation has been found to be an insensitive indicator of tissue temperature during RF delivery. We hypothesized that MB formation corresponds to surface-not tissue--temperature, and therefore would be an insensitive predictor of steam pops. An in vitro bovine heart model was used to measure surface and tissue temperatures during RF delivery under conditions designed to cause steam pops. Sensitivity of type II MB (MBII) formation as a predictor of steam pops and for surface temperatures more than 80 degrees C was calculated. Of 105 lesions delivered, 99 steam pops occurred. Twenty-one steam pops were preceded by MBII. MBII were seen in 26 lesions, five of which were not associated with steam pop. Surface temperature at onset of MBII was 87 +/- 9 degrees C versus a tissue temperature of 78 +/- 23 degrees C (P = 0.044). Surface temperature at the time of steam pops was 71 +/- 17 degrees C versus a tissue temperature of 102 +/- 17 degrees C (P < 0.0001). The sensitivity of MBII for steam pops was 21%, and 58% for detecting surface temperature in excess of 80 degrees C. MBII correlated better with surface temperature than with tissue temperature; steam pops, on the other hand, correlated better with tissue temperature. MBII was an insensitive marker of steam pops and surface temperature in excess of 80 degrees C. Therefore, MBII should not be used to titrate RF power.

40 CFR Appendix A to Subpart Uuuuu... - Hg Monitoring Provisions

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 15 2014-07-01 2014-07-01 false Hg Monitoring Provisions A Appendix A... Steam Generating Units Pt. 63, Subpt. UUUUU, App. A Appendix A to Subpart UUUUU of Part 63—Hg Monitoring Provisions 1. General Provisions 1.1Applicability. These monitoring provisions apply to the measurement of...

40 CFR Appendix A to Subpart Uuuuu... - Hg Monitoring Provisions

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 15 2013-07-01 2013-07-01 false Hg Monitoring Provisions A Appendix A... Steam Generating Units Pt. 63, Subpt. UUUUU, App. A Appendix A to Subpart UUUUU of Part 63—Hg Monitoring Provisions 1. General Provisions 1.1Applicability. These monitoring provisions apply to the measurement of...

A simplified version of the total Kjeldahl nitrogen method using an ammonia extraction ultrasound-assisted purge-and-trap system and ion chromatography for analyses of geological samples.

PubMed

Pontes, Fernanda V M; Carneiro, Manuel C; Vaitsman, Delmo S; da Rocha, Genilda P; da Silva, Lílian I D; Neto, Arnaldo A; Monteiro, Maria Inês C

2009-01-26

The total Kjeldahl nitrogen (TKN) method was simplified by using a manifold connected to a purge-and-trap system immersed into an ultrasonic (US) bath for simultaneous ammonia (NH(3)) extraction from many previously digested samples. Then, ammonia was collected in an acidic solution, converted to ammonium (NH(4)(+)), and finally determined by ion chromatography method. Some variables were optimized, such as ultrasonic irradiation power and frequency, ultrasound-assisted NH(3) extraction time, NH(4)(+) mass and sulfuric acid concentration added to the NH(3) collector flask. Recovery tests revealed no changes in the pH values and no conversion of NH(4)(+) into other nitrogen species during the irradiation of NH(4)Cl solutions with 25 or 40 kHz ultrasonic waves for up to 20 min. Sediment and oil free sandstone samples and soil certified reference materials (NCS DC 73319, NCS DC 73321 and NCS DC 73326) with different total nitrogen concentrations were analysed. The proposed method is faster, simpler and more sensitive than the classical Kjeldahl steam distillation method. The time for NH(3) extraction by the US-assisted purge-and-trap system (20 min) was half of that by the Kjeldahl steam distillation (40 min) for 10 previously digested samples. The detection limit was 9 microg g(-1)N, while for the Kjeldahl classical/indophenol method was 58 microg g(-1)N. Precision was always better than 13%. In the proposed method, carcinogenic reagents are not used, contrarily to the indophenol method. Furthermore, the proposed method can be adapted for fixed-NH(4)(+) determination.

Use of black light traps to monitor the abundance, spread, and flight behavior of Halyomorpha halys (Hemiptera: Pentatomidae).

PubMed

Nielsen, Anne L; Holmstrom, Kristian; Hamilton, George C; Cambridge, John; Ingerson-Mahar, Joseph

2013-06-01

Monitoring the distribution and abundance of an invasive species is challenging, especially during the initial years of spread when population densities are low and basic biology and monitoring methods are being investigated. Brown marmorated stink bug (Halyomorpha halys (Stål)) is an invasive agricultural and urban pest that was first detected in the United States in the late 1990s. At the time of its detection, no method was available to effectively track H. halys populations, which are highly mobile and polyphagous. One possible solution was the utilization of black light traps, which are nonspecific traps attractive to night flying insects. To determine if black light traps are a reliable monitoring tool for H. halys, a state-wide network of 40-75 traps located on New Jersey farms were monitored from 2004 to 2011 for H. halys. This proved to be a highly effective method of monitoring H. halys populations and their spread at the landscape level. The total number of brown marmorated stink bug caught in New Jersey increased exponentially during this period at a rate of 75% per year. Logistic regression estimates that 2.84 new farms are invaded each year by H. halys. The results indicate that black light traps are attractive to early season populations as well as at low population densities. Weekly trap catch data are being used to generate state-wide population distribution maps made available to farmers in weekly newsletters and online. While no economic threshold currently exists for brown marmorated stink bug, the maps provide farmers with a tool to forecast pest pressure and plan management.

Insect Biometrics: Optoacoustic Signal Processing and Its Applications to Remote Monitoring of McPhail Type Traps.

PubMed

Potamitis, Ilyas; Rigakis, Iraklis; Fysarakis, Konstantinos

2015-01-01

Monitoring traps are important components of integrated pest management applied against important fruit fly pests, including Bactrocera oleae (Gmelin) and Ceratitis capitata (Widemann), Diptera of the Tephritidae family, which effect a crop-loss/per year calculated in billions of euros worldwide. Pests can be controlled with ground pesticide sprays, the efficiency of which depends on knowing the time, location and extent of infestations as early as possible. Trap inspection is currently carried out manually, using the McPhail trap, and the mass spraying is decided based on a decision protocol. We introduce the term 'insect biometrics' in the context of entomology as a measure of a characteristic of the insect (in our case, the spectrum of its wingbeat) that allows us to identify its species and make devices to help face old enemies with modern means. We modify a McPhail type trap into becoming electronic by installing an array of photoreceptors coupled to an infrared emitter, guarding the entrance of the trap. The beating wings of insects flying in the trap intercept the light and the light fluctuation is turned to a recording. Custom-made electronics are developed that are placed as an external add-on kit, without altering the internal space of the trap. Counts from the trap are transmitted using a mobile communication network. This trap introduces a new automated remote-monitoring method different to audio and vision-based systems. We evaluate our trap in large number of insects in the laboratory by enclosing the electronic trap in insectary cages. Our experiments assess the potential of delivering reliable data that can be used to initialize reliably the spraying process at large scales but to also monitor the impact of the spraying process as it eliminates the time-lag between acquiring and delivering insect counts to a central agency.

Insect Biometrics: Optoacoustic Signal Processing and Its Applications to Remote Monitoring of McPhail Type Traps

PubMed Central

Potamitis, Ilyas; Rigakis, Iraklis; Fysarakis, Konstantinos

2015-01-01

Monitoring traps are important components of integrated pest management applied against important fruit fly pests, including Bactrocera oleae (Gmelin) and Ceratitis capitata (Widemann), Diptera of the Tephritidae family, which effect a crop-loss/per year calculated in billions of euros worldwide. Pests can be controlled with ground pesticide sprays, the efficiency of which depends on knowing the time, location and extent of infestations as early as possible. Trap inspection is currently carried out manually, using the McPhail trap, and the mass spraying is decided based on a decision protocol. We introduce the term ‘insect biometrics’ in the context of entomology as a measure of a characteristic of the insect (in our case, the spectrum of its wingbeat) that allows us to identify its species and make devices to help face old enemies with modern means. We modify a McPhail type trap into becoming electronic by installing an array of photoreceptors coupled to an infrared emitter, guarding the entrance of the trap. The beating wings of insects flying in the trap intercept the light and the light fluctuation is turned to a recording. Custom-made electronics are developed that are placed as an external add-on kit, without altering the internal space of the trap. Counts from the trap are transmitted using a mobile communication network. This trap introduces a new automated remote-monitoring method different to audio and vision-based systems. We evaluate our trap in large number of insects in the laboratory by enclosing the electronic trap in insectary cages. Our experiments assess the potential of delivering reliable data that can be used to initialize reliably the spraying process at large scales but to also monitor the impact of the spraying process as it eliminates the time-lag between acquiring and delivering insect counts to a central agency. PMID:26544845

40 CFR 60.4350 - How do I use data from the continuous emission monitoring equipment to identify excess emissions?

Code of Federal Regulations, 2013 CFR

2013-07-01

... energy output of the combustion turbine in MW. (2) For combined-cycle and combined heat and power... the heat recovery steam generator, and 100 percent of the total useful thermal energy output that is... Where: Ps = useful thermal energy of the steam, measured relative to ISO conditions, not used to...

40 CFR 60.4350 - How do I use data from the continuous emission monitoring equipment to identify excess emissions?

Code of Federal Regulations, 2012 CFR

2012-07-01

... energy output of the combustion turbine in MW. (2) For combined-cycle and combined heat and power... the heat recovery steam generator, and 100 percent of the total useful thermal energy output that is... Where: Ps = useful thermal energy of the steam, measured relative to ISO conditions, not used to...

40 CFR 60.4350 - How do I use data from the continuous emission monitoring equipment to identify excess emissions?

Code of Federal Regulations, 2011 CFR

2011-07-01

... energy output of the combustion turbine in MW. (2) For combined-cycle and combined heat and power... the heat recovery steam generator, and 100 percent of the total useful thermal energy output that is... Where: Ps = useful thermal energy of the steam, measured relative to ISO conditions, not used to...

40 CFR 60.4350 - How do I use data from the continuous emission monitoring equipment to identify excess emissions?

Code of Federal Regulations, 2014 CFR

2014-07-01

... energy output of the combustion turbine in MW. (2) For combined-cycle and combined heat and power... the heat recovery steam generator, and 100 percent of the total useful thermal energy output that is... Where: Ps = useful thermal energy of the steam, measured relative to ISO conditions, not used to...

The Effect of a Climate Change Monitoring Program on Students' Knowledge and Perceptions of STEAM Education in Korea

ERIC Educational Resources Information Center

Jeong, Sophia; Kim, Hyoungbum

2015-01-01

Korea has recently started to implement a STEM-like approach in K-12 education, titled STEAM (Science, Technology, Engineering, Arts, and Mathematics) curriculum, to educate the next generation of students to become creative innovators. As this approach has been shown to increase educational success, it is vital to prepare and develop interest in…

Microwave limb sounding of the UT/LS: Stratosphere-Troposphere Exchange And Climate Monitor (STEAM) and related projects

NASA Astrophysics Data System (ADS)

Urban, Joachim

The Stratosphere-Troposphere Exchange And climate Monitor (STEAM) radiometer is designed to provide vertically and horizontally well resolved profiles of key species in the climate relevant upper troposphere and lower stratosphere (UT/LS) altitude region such as H2O, O3, CO, HCN, CH3CN, CH3Cl, N2O, HNO3, and temperature. The instrument is a multi-beam limb sounder employing 12GHz wide sub-harmonically pumped double sideband mixers targeting the 324-336GHz (lower sideband) and 343.25-355.25GHz (upper sideband) spectral bands with a local oscillator set at 339.625GHz. Whilst the instrument configuration had been optimized during the recent years to fit the ESA Earth Explorer 7 candidate mission PREMIER, the instrument payload is now being studied in a smaller configuration for a different satellite mission in collaboration with international partners. The presentation provides an overview of the STEAM project and its science objectives and focuses on a description of the measurement capabilities of the newly configured STEAM radiometer, in comparison to related projects and existing sensors such as Odin/SMR and Aura/MLS.

Oil Sands Characteristics and Time-Lapse and P-SV Seismic Steam Monitoring, Athabasca, Canada

NASA Astrophysics Data System (ADS)

Takahashi, A.; Nakayama, T.; Kashihara, K.; Skinner, L.; Kato, A.

2008-12-01

A vast amount of oil sands exists in the Athabasca area, Alberta, Canada. These oil sands consist of bitumen (extra-heavy oil) and unconsolidated sand distributed from surface to a depth of 750 meters. Including conventional crude oil, the total number of proved remaining oil reserves in Canada ranks second place in the world after Saudi Arabia. For the production of bitumen from the reservoir 200 to 500 meters in depth, the Steam Assisted Gravity Drainage (SAGD) method (Steam Injection EOR) has been adopted as bitumen is not movable at original temperatures. It is essential to understand the detailed reservoir distribution and steam chamber development extent for optimizing the field development. Oil sands reservoir characterization is conducted using 3D seismic data acquired in February 2002. Conducting acoustic impedance inversion to improve resolution and subsequent multi-attribute analysis integrating seismic data with well data facilitates an understanding of the detailed reservoir distribution. These analyses enable the basement shale to be imaged, and enables identification to a certain degree of thin shale within the reservoir. Top and bottom depths of the reservoir are estimated in the range of 2.0 meters near the existing wells even in such a complex channel sands environment characterized by abrupt lateral sedimentary facies changes. In March 2006, monitoring 3D seismic data was acquired to delineate steam-affected areas. The 2002 baseline data is used as a reference data and the 2006 monitoring data is calibrated to the 2002 seismic data. Apparent differences in the two 3D seismic data sets with the exception of production related response changes are removed during the calibration process. P-wave and S-wave velocities of oil sands core samples are also measured with various pressures and temperatures, and the laboratory measurement results are then combined to construct a rock physics model used to predict velocity changes induced by steam-injection. The differences of the seismic responses between the time-lapse seismic volumes can be quantitatively explained by P-wave velocity decrease of the oil sands layers due to steam-injection. In addition, the data suggests that a larger area would be influenced by pressure than temperature. We calculate several seismic attributes such as RMS values of amplitude difference, maximum cross correlations, and interval velocity differences. These attributes are integrated by using self-organization maps (SOM) and K-means methods. By this analysis, we are able to distinguish areas of steam chamber growth from transitional and non-affected areas. In addition, 3D P-SV converted-wave processing and analysis are applied on the second 3D data set (recorded with three-component digital sensor). Low Vp/Vs values in the P-SV volume show areas of steam chamber development, and high Vp/Vs values indicate transitional zones. Our analysis of both time-lapse 3D seismic and 3D P-SV data along with the rock physics model can be used to monitor qualitatively and quantitatively the rock property changes of the inter-well reservoir sands in the field.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dougan, P.M.

During the year, design, construction and installation of all project equipment was completed, and continuous steam injection began on September 18, 1979 and continued until February 29, 1980. In the five-month period of steam injection, 235,060 barrels of water as steam at an average wellhead pressure of 1199 psig and an average wellhead temperature of 456/sup 0/F were injected into the eight project injection wells. Operation of the project at design temperature and pressure (1000/sup 0/F and 1500 psig) was not possible due to continuing problems with surface equipment. Environmental monitoring at the project site continued during startup and operation.

40 CFR 146.23 - Operating, monitoring, and reporting requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the injection phase of cyclic steam operations And recording of one observation of injection pressure...; (4) Maintenance of the results of all monitoring until the next permit review (see 40 CFR 144.52(a)(5...

40 CFR 146.23 - Operating, monitoring, and reporting requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... the injection phase of cyclic steam operations And recording of one observation of injection pressure...; (4) Maintenance of the results of all monitoring until the next permit review (see 40 CFR 144.52(a)(5...

40 CFR 146.23 - Operating, monitoring, and reporting requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... the injection phase of cyclic steam operations And recording of one observation of injection pressure...; (4) Maintenance of the results of all monitoring until the next permit review (see 40 CFR 144.52(a)(5...

40 CFR 146.23 - Operating, monitoring, and reporting requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... the injection phase of cyclic steam operations And recording of one observation of injection pressure...; (4) Maintenance of the results of all monitoring until the next permit review (see 40 CFR 144.52(a)(5...

High Temperatures Health Monitoring of the Condensed Water Height in Steam Pipe Systems

NASA Technical Reports Server (NTRS)

Lih, Shyh-Shiuh; Bar-Cohen, Yoseph; Lee, Hyeong Jae; Badescu, Mircea; Bao, Xiaoqi; Sherrit, Stewart; Takano, Nobuyuki; Ostlund, Patrick; Blosiu, Julian

2013-01-01

Ultrasonic probes were designed, fabricated and tested for high temperature health monitoring system. The goal of this work was to develop the health monitoring system that can determine the height level of the condensed water through the pipe wall at high temperature up to 250 deg while accounting for the effects of surface perturbation. Among different ultrasonic probe designs, 2.25 MHz probes with air backed configuration provide satisfactory results in terms of sensitivity, receiving reflections from the target through the pipe wall. A series of tests were performed using the air-backed probes under irregular conditions, such as surface perturbation and surface disturbance at elevated temperature, to qualify the developed ultrasonic system. The results demonstrate that the fabricated air-backed probes combined with advanced signal processing techniques offer the capability of health monitoring of steam pipe under various operating conditions.

Use of borehole radar reflection logging to monitor steam-enhanced remediation in fractured limestone-results of numerical modelling and a field experiment

USGS Publications Warehouse

Gregoire, C.; Joesten, P.K.; Lane, J.W.

2006-01-01

Ground penetrating radar is an efficient geophysical method for the detection and location of fractures and fracture zones in electrically resistive rocks. In this study, the use of down-hole (borehole) radar reflection logs to monitor the injection of steam in fractured rocks was tested as part of a field-scale, steam-enhanced remediation pilot study conducted at a fractured limestone quarry contaminated with chlorinated hydrocarbons at the former Loring Air Force Base, Limestone, Maine, USA. In support of the pilot study, borehole radar reflection logs were collected three times (before, during, and near the end of steam injection) using broadband 100 MHz electric dipole antennas. Numerical modelling was performed to predict the effect of heating on radar-frequency electromagnetic (EM) wave velocity, attenuation, and fracture reflectivity. The modelling results indicate that EM wave velocity and attenuation change substantially if heating increases the electrical conductivity of the limestone matrix. Furthermore, the net effect of heat-induced variations in fracture-fluid dielectric properties on average medium velocity is insignificant because the expected total fracture porosity is low. In contrast, changes in fracture fluid electrical conductivity can have a significant effect on EM wave attenuation and fracture reflectivity. Total replacement of water by steam in a fracture decreases fracture reflectivity of a factor of 10 and induces a change in reflected wave polarity. Based on the numerical modelling results, a reflection amplitude analysis method was developed to delineate fractures where steam has displaced water. Radar reflection logs collected during the three acquisition periods were analysed in the frequency domain to determine if steam had replaced water in the fractures (after normalizing the logs to compensate for differences in antenna performance between logging runs). Analysis of the radar reflection logs from a borehole where the temperature increased substantially during the steam injection experiment shows an increase in attenuation and a decrease in reflectivity in the vicinity of the borehole. Results of applying the reflection amplitude analysis method developed for this study indicate that steam did not totally replace the water in most of the fractures. The observed decreases in reflectivity were consistent with an increase in fracture-water temperature, rather than the presence of steam. A limiting assumption of the reflection amplitude analysis method is the requirement for complete displacement of water in a fracture by steam. ?? 2006 Elsevier B.V. All rights reserved.

Use of Borehole-Radar Methods to Monitor a Steam-Enhanced Remediation Pilot Study at a Quarry at the Former Loring Air Force Base, Maine

USGS Publications Warehouse

Gregoire, Colette; Joesten, Peter K.; Lane, John W.

2007-01-01

Single-hole radar reflection and crosshole radar tomography surveys were used in conjunction with conventional borehole-geophysical methods to evaluate the effectiveness of borehole-radar methods for monitoring the movement of steam and heat through fractured bedrock. The U.S. Geological Survey, in cooperation with U.S. Environmental Protection Agency (USEPA), conducted surveys in an abandoned limestone quarry at the former Loring Air Force Base during a field-scale, steam-enhanced remediation (SER) pilot project conducted by the USEPA, the U.S. Air Force, and the Maine Department of Environmental Protection to study the viability of SER to remediate non-aqueous phase liquid contamination in fractured bedrock. Numerical modeling and field experiments indicate that borehole-radar methods have the potential to monitor the presence of steam and to measure large temperature changes in the limestone matrix during SER operations. Based on modeling results, the replacement of water by steam in fractures should produce a decrease in radar reflectivity (amplitude of the reflected wave) by a factor of 10 and a change in reflection polarity. In addition, heating the limestone matrix should increase the bulk electrical conductivity and decrease the bulk dielectric permittivity. These changes result in an increase in radar attenuation and an increase in radar-wave propagation velocity, respectively. Single-hole radar reflection and crosshole radar tomography data were collected in two boreholes using 100-megahertz antennas before the start of steam injection, about 10 days after the steam injection began, and 2 months later, near the end of the injection. Fluid temperature logs show that the temperature of the fluid in the boreholes increased by 10?C (degrees Celsius) in one borehole and 40?C in the other; maximum temperatures were measured near the bottom of the boreholes. The results of the numerical modeling were used to interpret the borehole-radar data. Analyses of the single-hole radar reflection data showed almost no indication that steam replaced water in fractures near the boreholes because (1) no change of polarity was observed in the radar reflections; (2) variations in the measured traveltimes were unsubstantial; and (3) most of the observed decreases in reflectivity were too small to have resulted from the replacement of water by steam. Analyses of the crosshole radar tomography data also support the conclusion that steam did not replace water in the fractures around the boreholes because traveltime-difference and attenuation-difference tomograms showed only small decreases in velocity and small increases in attenuation accompanying the steam injection. The radar data are consistent with an increase in the conductivity of the limestone as a result of heating of the limestone matrix near the boreholes. Single-hole radar reflection data collected near the end of the steam injection near the bottom of the borehole with the largest temperature increase showed substantial attenuation. Also, reflector analysis showed small decreases in the amplitudes of radar-wave reflections in data collected before injection and data collected near the end of the collection period. In the crosshole radar tomography data, decreases in velocity and small increases in attenuation also are consistent with temperature increases in the matrix.

Development of semiochemical attractants for monitoring bean seed beetle, Bruchus rufimanus.

PubMed

Bruce, Toby J A; Martin, Janet L; Smart, Lesley E; Pickett, John A

2011-10-01

Bruchus rufimanus is a serious pest of field beans. The objective here was to develop a semiochemical-baited trapping system to facilitate monitoring of the pest. Volatile compounds that were electrophysiologically active with the antennae of B. rufimanus females were identified from headspace samples of Vicia faba flowers and from male B. rufimanus. Selected headspace samples and synthetic compounds were tested in olfactometer bioassays. The semiochemicals were then formulated in lures for traps and evaluated in a field trapping experiment. Cone traps baited with a three-component blend of floral volatiles, releasing (R)-linalool (17.7 mg day(-1)), cinnamyl alcohol (0.4 mg day(-1)) and cinnamaldehyde (0.77 mg day(-1)), caught significantly more of both sexes of B. rufimanus than unbaited control traps. A male volatile, 1-undecene, was EAG active with female antennae. It was attractive to females in an olfactometer, indicating that it is a sex pheromone. However, in the field it only enhanced trap catches if it was released together with the floral volatiles. The blends of semiochemicals identified were shown to be attractive in cone traps under field conditions. The prototype trapping system developed could be used as a monitoring tool to determine infestation levels of B. rufimanus in bean fields. Copyright © 2011 Society of Chemical Industry.

Field optimization of the sex pheromone of Stenoma catenifer (Lepidoptera: Elachistidae): evaluation of lure types, trap height, male flight distances, and number of traps needed per avocado orchard for detection.

PubMed

Hoddle, M S; Millar, J G; Hoddle, C D; Zou, Y; McElfresh, J S; Lesch, S M

2011-04-01

The sex pheromone of Stenoma catenifer was evaluated in commercial avocado orchards in Guatemala to determine operational parameters, such as optimal lure type, trap height, trap density and estimates of the distances that male moths fly. Of four pheromone dispensers tested, gray and white rubber septa were of equal efficacy, whereas 1-ml low-density polyethylene vials and 2×3-cm polyethylene ziplock bags were least efficacious. The height at which wing traps were hung did not significantly affect the number of adult male S. catenifer captured. For monitoring S. catenifer, these data suggest that the pheromone should be dispensed from gray rubber septa in wing traps hung inside the tree canopy at 1.75 m, a height convenient for trap placement and monitoring. Mark-recapture studies of male S. catenifer indicated that, on average, males flew 67 m in one night. However, it is likely that this is an underestimate of the distance that male moths are capable of flying in a single night. Probabilistic modeling of S. catenifer capture data from different numbers of pheromone traps deployed in seven commercial avocado orchards of varying sizes and infestation levels suggested that 10-13 randomly deployed traps per orchard for a 7-day period are needed to detect at least one male S. catenifer with 90% confidence. These data provide sufficient information to develop effective protocols for using the S. catenifer pheromone to detect and monitor this pest in countries with endemic populations that are exporting fresh avocados, and for quarantine detection and incursion monitoring in countries receiving avocado imports from high risk areas.

Evaluation of Food Lures for Capture and Monitoring of Anastrepha fraterculus (Diptera: Tephritidae) on Temperate Fruit Trees.

PubMed

Rosa, J M da; Arioli, C J; Santos, J P Dos; Menezes-Netto, A C; Botton, M

2017-06-01

The Anastrepha fraterculus (Wiedemann) (Diptera: Tephritidae) is the main pest of fruit trees grown in temperate climates in the southern region of Brazil. The objective of this work was to evaluate the efficiency of the major commercial food lures used in Brazil for trapping and monitoring of A. fraterculus in plum, pear, and feijoa orchards. The assessed lures were hydrolyzed proteins of animal origin (CeraTrap) and plant origin (BioAnastrepha), torula yeast + borax (Torula), and grape juice. Response variables included the rate of adult capture (flies per trap per day, FTD) and the percentage of females captured. We also evaluated the number of times the weekly capture rate exceeded the traditional threshold of 0.5 FTD for each lure. Traps baited with grape juice, currently used for monitoring A. fraterculus in Southern Brazil, captured fewer adults and a lower percentage of females compared with the other lures. CeraTrap trapped a greater number of A. fraterculus adults and, in some cases, a lower percentage of females compared with the other lures in pears. Traps baited with CeraTrap had greater capture rates (FTD), particularly during the stages of fruit maturation and harvest, and even in years with low population density of A. fraterculus, thus demonstrating greater sensitivity in the detection of this pest. These results show that, in order to detect and monitor the presence of A. fraterculus in plum, feijoa, and pear crops, protein-based lures are superior to grape juice, especially the animal protein CeraTrap. © The Authors 2017. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

40 CFR Table 7 to Subpart Jjj of... - Group 1 Batch Process Vents and Aggregate Batch Vent Streams-Monitoring, Recordkeeping, and...

Code of Federal Regulations, 2012 CFR

2012-07-01

... collected—PR. d,e Carbon Adsorber f a. Total regeneration steam flow or nitrogen flow, or pressure (gauge or absolute) during carbon bed regeneration cycle(s), and 1. Record the total regeneration steam flow or nitrogen flow, or pressure for each carbon bed regeneration cycle.2. Record and report the total...

40 CFR Table 6 to Subpart U of... - Group 1 Batch Front-End Process Vents and Aggregate Batch Vent Streams-Monitoring, Recordkeeping...

Code of Federal Regulations, 2012 CFR

2012-07-01

... collected—PR. d,e Carbon adsorber f a. Total regeneration steam flow or nitrogen flow, or pressure gauge or absolute) during carbon bed regeneration cycle(s), and 1. Record of total regeneration steam flow or nitrogen flow, or pressure for each carbon bed regeneration cycle. 2. Record and report the total...

40 CFR Table 6 to Subpart U of... - Group 1 Batch Front-End Process Vents and Aggregate Batch Vent Streams-Monitoring, Recordkeeping...

Code of Federal Regulations, 2011 CFR

2011-07-01

... collected—PR. d,e Carbon adsorber f a. Total regeneration steam flow or nitrogen flow, or pressure gauge or absolute) during carbon bed regeneration cycle(s), and 1. Record of total regeneration steam flow or nitrogen flow, or pressure for each carbon bed regeneration cycle. 2. Record and report the total...

40 CFR Table 7 to Subpart Jjj of... - Group 1 Batch Process Vents and Aggregate Batch Vent Streams-Monitoring, Recordkeeping, and...

Code of Federal Regulations, 2010 CFR

2010-07-01

... collected—PR. d,e Carbon Adsorber f a. Total regeneration steam flow or nitrogen flow, or pressure (gauge or absolute) during carbon bed regeneration cycle(s), and 1. Record the total regeneration steam flow or nitrogen flow, or pressure for each carbon bed regeneration cycle.2. Record and report the total...

40 CFR Table 6 to Subpart U of... - Group 1 Batch Front-End Process Vents and Aggregate Batch Vent Streams-Monitoring, Recordkeeping...

Code of Federal Regulations, 2013 CFR

2013-07-01

... collected—PR. d,e Carbon adsorber f a. Total regeneration steam flow or nitrogen flow, or pressure gauge or absolute) during carbon bed regeneration cycle(s), and 1. Record of total regeneration steam flow or nitrogen flow, or pressure for each carbon bed regeneration cycle. 2. Record and report the total...

40 CFR Table 6 to Subpart U of... - Group 1 Batch Front-End Process Vents and Aggregate Batch Vent Streams-Monitoring, Recordkeeping...

Code of Federal Regulations, 2010 CFR

2010-07-01

... collected—PR. d,e Carbon adsorber f a. Total regeneration steam flow or nitrogen flow, or pressure gauge or absolute) during carbon bed regeneration cycle(s), and 1. Record of total regeneration steam flow or nitrogen flow, or pressure for each carbon bed regeneration cycle. 2. Record and report the total...

40 CFR Table 7 to Subpart Jjj of... - Group 1 Batch Process Vents and Aggregate Batch Vent Streams-Monitoring, Recordkeeping, and...

Code of Federal Regulations, 2013 CFR

2013-07-01

... collected—PR. d,e Carbon Adsorber f a. Total regeneration steam flow or nitrogen flow, or pressure (gauge or absolute) during carbon bed regeneration cycle(s), and 1. Record the total regeneration steam flow or nitrogen flow, or pressure for each carbon bed regeneration cycle.2. Record and report the total...

40 CFR Table 7 to Subpart Jjj of... - Group 1 Batch Process Vents and Aggregate Batch Vent Streams-Monitoring, Recordkeeping, and...

Code of Federal Regulations, 2011 CFR

2011-07-01

... collected—PR. d,e Carbon Adsorber f a. Total regeneration steam flow or nitrogen flow, or pressure (gauge or absolute) during carbon bed regeneration cycle(s), and 1. Record the total regeneration steam flow or nitrogen flow, or pressure for each carbon bed regeneration cycle.2. Record and report the total...

40 CFR Table 6 to Subpart U of... - Group 1 Batch Front-End Process Vents and Aggregate Batch Vent Streams-Monitoring, Recordkeeping...

Code of Federal Regulations, 2014 CFR

2014-07-01

... collected—PR. d e Carbon adsorber f a. Total regeneration steam flow or nitrogen flow, or pressure gauge or absolute) during carbon bed regeneration cycle(s), and 1. Record of total regeneration steam flow or nitrogen flow, or pressure for each carbon bed regeneration cycle. 2. Record and report the total...

40 CFR Table 7 to Subpart Jjj of... - Group 1 Batch Process Vents and Aggregate Batch Vent Streams-Monitoring, Recordkeeping, and...

Code of Federal Regulations, 2014 CFR

2014-07-01

... collected—PR. d e Carbon Adsorber f a. Total regeneration steam flow or nitrogen flow, or pressure (gauge or absolute) during carbon bed regeneration cycle(s), and 1. Record the total regeneration steam flow or nitrogen flow, or pressure for each carbon bed regeneration cycle.2. Record and report the total...

Corrective Action Plan for Corrective Action Unit 562: Waste Systems, Nevada National Security Site, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

NSTec Environmental Restoration

2011-04-30

This Corrective Action Plan has been prepared for Corrective Action Unit (CAU) 562, Waste Systems, in accordance with the Federal Facility Agreement and Consent Order (1996; as amended March 2010). CAU 562 consists of 13 Corrective Action Sites (CASs) located in Areas 2, 23, and 25 of the Nevada National Security Site. Site characterization activities were performed in 2009 and 2010, and the results are presented in Appendix A of the Corrective Action Decision Document for CAU 562. The scope of work required to implement the recommended closure alternatives is summarized. (1) CAS 02-26-11, Lead Shot, will be clean closedmore » by removing shot. (2) CAS 02-44-02, Paint Spills and French Drain, will be clean closed by removing paint and contaminated soil. As a best management practice (BMP), asbestos tile will be removed. (3) CAS 02-59-01, Septic System, will be clean closed by removing septic tank contents. As a BMP, the septic tank will be removed. (4) CAS 02-60-01, Concrete Drain, contains no contaminants of concern (COCs) above action levels. No further action is required; however, as a BMP, the concrete drain will be removed. (5) CAS 02-60-02, French Drain, was clean closed. Corrective actions were completed during corrective action investigation activities. As a BMP, the drain grates and drain pipe will be removed. (6) CAS 02-60-03, Steam Cleaning Drain, will be clean closed by removing contaminated soil. As a BMP, the steam cleaning sump grate and outfall pipe will be removed. (7) CAS 02-60-04, French Drain, was clean closed. Corrective actions were completed during corrective action investigation activities. (8) CAS 02-60-05, French Drain, will be clean closed by removing contaminated soil. (9) CAS 02-60-06, French Drain, contains no COCs above action levels. No further action is required. (10) CAS 02-60-07, French Drain, requires no further action. The french drain identified in historical documentation was not located during corrective action investigation activities. (11) CAS 23-60-01, Mud Trap Drain and Outfall, will be clean closed by removing sediment from the mud trap. As a BMP, the mud trap and outfall pipe will be removed. (12) CAS 23-99-06, Grease Trap, will be clean closed by removing sediment from the grease trap and backfilling the grease trap with grout. (13) CAS 25-60-04, Building 3123 Outfalls, will be clean closed by removing contaminated soil and the sludge-containing outfall pipe.« less

40 CFR 75.15 - Special provisions for measuring Hg mass emissions using the excepted sorbent trap monitoring...

Code of Federal Regulations, 2010 CFR

2010-07-01

... the excepted sorbent trap monitoring methodology. For an affected coal-fired unit under a State or...; (c) A certified flow monitoring system is required; (d) Correction for stack gas moisture content is... proportional to the stack gas volumetric flow rate. (f) At the beginning and end of each sample collection...

Rockfall Milepoint 49 Monitoring Plan for Check Dams on Mt. Hood Highway (US 26) (M.P. 49.10 to M.P. 49.23)

DOT National Transportation Integrated Search

2003-07-31

This Stormwater BMP Monitoring Plan details the approach to be used for monitoring : roadside ditch sediment traps located on Highway 26 in the Mt. Hood National Forest. : These sediment traps were designed and installed by ODOT for the capture of se...

Measuring the Effective Sampling Area of a Pheromone Trap for Monitoring Population Density of Southern Pine Beetle (Coleoptera: Scolytidae)

Treesearch

Peter Turchin; Francois J. Odendaal

1996-01-01

Multifunnel traps baited with frontalin and turpentine have been used to investigate dispersal of southern pine beetles, Dendroctonus front Zimmermann, and are routinely used in the southern United States to monitor population trends of this serious forest pest. However, there is no quantitative data on the effective sampling area of these traps that would allow us to...

Development of High-Powered Steam Turbines by OAO NPO Central Research and Design Institute for Boilers and Turbines

NASA Astrophysics Data System (ADS)

Mikhailov, V. E.; Khomenok, L. A.; Kovalev, I. A.

2018-01-01

The article provides an overview of the developments by OAO NPO TsKTI aimed at improvement of components and assemblies of new-generation turbine plants for ultra-supercritical steam parameters to be installed at the power-generating facilities in service. The list of the assemblies under development includes cylinder shells, the cylinder's flow paths and rotors, seals, bearings, and rotor cooling systems. The authors consider variants of the shafting-cylinder configurations for which advanced high-pressure and intermediate-pressure cylinders with reactive blading and low-pressure cylinders of conventional design and with counter-current steam flows are proposed and high-pressure rotors, which can increase the economic efficiency and reduce the overall turbine plant dimensions. Materials intended for the equipment components that operate at high temperatures and a steam cooling technique that allows the use of cheaper steel grades owing to the reduction in the metal's working temperature are proposed. A new promising material for the bearing surfaces is described that enables the operation at higher unit pressures. The material was tested on a full-scale test bench at OAO NPO TsKTI and a turbine in operation. Ways of controlling the erosion of the blades in the moisture-steam turbine compartments by the steam heating of the hollow guide blades are considered. To ensure the dynamic stability of the shafting, shroud and diaphragm seals that prevent the development of the destabilizing circulatory forces of the steam flow were devised and trialed. Advanced instrumentation and software are proposed to monitor the condition of the blading and thermal stresses under transient conditions, to diagnose the vibration processes, and to archive the obtained data. Attention is paid to the normalization of the electromagnetic state of the plant in order to prevent the electrolytic erosion of the plant components. The instrumentation intended for monitoring the relevant electric parameters is described.

A comparison of gravid and under-house CO2-baited CDC light traps for mosquito species of public health importance in Houston, Texas.

PubMed

White, Stephanie L; Ward, Michael P; Budke, Christine M; Cyr, Tracy; Bueno, Rudy

2009-11-01

The relative efficacy of gravid and under-house CO2 traps for monitoring mosquito species of public health importance within the Houston metroplex area was assessed. Gravid and under-house traps were colocated at 10 sites and monitored weekly between 1 March to 31 May 2007. The most numerous species caught was Culex pipiens quinquefasciatus Say. Other species of public health importance caught in gravid and under-house traps included Culex restuans Theobald, Aedes aegypti (L.), and Aedes albopictus Skuse. Adjusting for the week of collection, gravid traps caught significantly more mosquitoes (mean 23.1 per trap) in the study area than under-house traps (mean 3.6 per trap). However, under-house traps caught a greater variety of mosquito species (13) than gravid traps (11). Gravid and under-house traps only caught nine of 15 of the same mosquito species during the study period. In this study area, gravid traps should be used as the primary method of surveillance for mosquito-borne diseases of public health importance during the early part of the season, because of greater catch numbers of mosquitoes that pose a public health risk.

Captures of Boll Weevils (Coleoptera: Curculionidae) in Relation to Trap Orientation and Distance From Brush Lines.

PubMed

Spurgeon, Dale W

2016-04-01

Eradication programs for the boll weevil (Anthonomus grandis grandis Boheman) rely on pheromone-baited traps to trigger insecticide treatments and monitor program progress. A key objective of monitoring in these programs is the timely detection of incipient weevil populations to limit or prevent re-infestation. Therefore, improvements in the effectiveness of trapping would enhance efforts to achieve and maintain eradication. Association of pheromone traps with woodlots and other prominent vegetation are reported to increase captures of weevils, but the spatial scale over which this effect occurs is unknown. The influences of trap distance (0, 10, and 20 m) and orientation (leeward or windward) to brush lines on boll weevil captures were examined during three noncropping seasons (October to February) in the Rio Grande Valley of Texas. Differences in numbers of captured weevils and in the probability of capture between traps at 10 or 20 m from brush, although often statistically significant, were generally small and variable. Variations in boll weevil population levels, wind directions, and wind speeds apparently contributed to this variability. In contrast, traps closely associated with brush (0 m) generally captured larger numbers of weevils, and offered a higher probability of weevil capture compared with traps away from brush. These increases in the probability of weevil capture were as high as 30%. Such increases in the ability of traps to detect low-level boll weevil populations indicate trap placement with respect to prominent vegetation is an important consideration in maximizing the effectiveness of trap-based monitoring for the boll weevil.

Non-fluorescent nanoscopic monitoring of a single trapped nanoparticle via nonlinear point sources.

PubMed

Yoon, Seung Ju; Lee, Jungmin; Han, Sangyoon; Kim, Chang-Kyu; Ahn, Chi Won; Kim, Myung-Ki; Lee, Yong-Hee

2018-06-07

Detection of single nanoparticles or molecules has often relied on fluorescent schemes. However, fluorescence detection approaches limit the range of investigable nanoparticles or molecules. Here, we propose and demonstrate a non-fluorescent nanoscopic trapping and monitoring platform that can trap a single sub-5-nm particle and monitor it with a pair of floating nonlinear point sources. The resonant photon funnelling into an extremely small volume of ~5 × 5 × 7 nm 3 through the three-dimensionally tapered 5-nm-gap plasmonic nanoantenna enables the trapping of a 4-nm CdSe/ZnS quantum dot with low intensity of a 1560-nm continuous-wave laser, and the pumping of 1560-nm femtosecond laser pulses creates strong background-free second-harmonic point illumination sources at the two vertices of the nanoantenna. Under the stable trapping conditions, intermittent but intense nonlinear optical spikes are observed on top of the second-harmonic signal plateau, which is identified as the 3.0-Hz Kramers hopping of the quantum dot trapped in the 5-nm gap.

Acoustic signal emission monitoring as a novel method to predict steam pops during radiofrequency ablation: preliminary observations.

PubMed

Chik, William W B; Kosobrodov, Roman; Bhaskaran, Abhishek; Barry, Michael Anthony Tony; Nguyen, Doan Trang; Pouliopoulos, Jim; Byth, Karen; Sivagangabalan, Gopal; Thomas, Stuart P; Ross, David L; McEwan, Alistair; Kovoor, Pramesh; Thiagalingam, Aravinda

2015-04-01

Steam pop is an explosive rupture of cardiac tissue caused by tissue overheating above 100 °C, resulting in steam formation, predisposing to serious complications associated with radiofrequency (RF) ablations. However, there are currently no reliable techniques to predict the occurrence of steam pops. We propose the utility of acoustic signals emitted during RF ablation as a novel method to predict steam pop formation and potentially prevent serious complications. Radiofrequency generator parameters (power, impedance, and temperature) were temporally recorded during ablations performed in an in vitro bovine myocardial model. The acoustic system consisted of HTI-96-min hydrophone, microphone preamplifier, and sound card connected to a laptop computer. The hydrophone has the frequency range of 2 Hz to 30 kHz and nominal sensitivity in the range -240 to -165 dB. The sound was sampled at 96 kHz with 24-bit resolution. Output signal from the hydrophone was fed into the camera audio input to synchronize the video stream. An automated system was developed for the detection and analysis of acoustic events. Nine steam pops were observed. Three distinct sounds were identified as warning signals, each indicating rapid steam formation and its release from tissue. These sounds had a broad frequency range up to 6 kHz with several spectral peaks around 2-3 kHz. Subjectively, these warning signals were perceived as separate loud clicks, a quick succession of clicks, or continuous squeaking noise. Characteristic acoustic signals were identified preceding 80% of pops occurrence. Six cardiologists were able to identify 65% of acoustic signals accurately preceding the pop. An automated system identified the characteristic warning signals in 85% of cases. The mean time from the first acoustic signal to pop occurrence was 46 ± 20 seconds. The automated system had 72.7% sensitivity and 88.9% specificity for predicting pops. Easily identifiable characteristic acoustic emissions predictably occur before imminent steam popping during RF ablations. Such acoustic emissions can be carefully monitored during an ablation and may be useful to prevent serious complications during RF delivery. © 2014 Wiley Periodicals, Inc.

40 CFR 60.47b - Emission monitoring for sulfur dioxide.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Emission monitoring for sulfur dioxide... Industrial-Commercial-Institutional Steam Generating Units § 60.47b Emission monitoring for sulfur dioxide... generating unit and analyzing them for sulfur and heat content according to Method 19 of appendix A of this...

40 CFR 60.47b - Emission monitoring for sulfur dioxide.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Emission monitoring for sulfur dioxide... Industrial-Commercial-Institutional Steam Generating Units § 60.47b Emission monitoring for sulfur dioxide... generating unit and analyzing them for sulfur and heat content according to Method 19 of appendix A of this...

40 CFR 60.47b - Emission monitoring for sulfur dioxide.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Emission monitoring for sulfur dioxide... Industrial-Commercial-Institutional Steam Generating Units § 60.47b Emission monitoring for sulfur dioxide... generating unit and analyzing them for sulfur and heat content according to Method 19 of appendix A of this...

40 CFR 60.47b - Emission monitoring for sulfur dioxide.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Emission monitoring for sulfur dioxide... Industrial-Commercial-Institutional Steam Generating Units § 60.47b Emission monitoring for sulfur dioxide... generating unit and analyzing them for sulfur and heat content according to Method 19 of appendix A of this...

40 CFR 60.47b - Emission monitoring for sulfur dioxide.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Emission monitoring for sulfur dioxide... Industrial-Commercial-Institutional Steam Generating Units § 60.47b Emission monitoring for sulfur dioxide... generating unit and analyzing them for sulfur and heat content according to Method 19 of appendix A of this...

Hypersensitivity pneumonitis in a beautician.

PubMed

Soumagne, Thibaud; Reboux, Gabriel; Degano, Bruno; Dalphin, Jean Charles

2016-11-01

A 52-year-old non-smoking beautician using a skincare device spraying steam and ozone (a "vapozone" facial steamer) was referred for progressive dyspnea and dry cough during working periods. Although spirometry was normal, she had decreased diffusing capacity of the lung for carbon monoxide, bronchiolitis with air trapping on high-resolution CT scan and 60% lymphocytosis by bronchoalveolar lavage. Twenty-six antigens were tested and serum-specific precipitins were found mainly against Pseudomonas sp. and Mycobacterium mucogenicum. Cultures from her skincare device isolated Pseudomonas sp. Outcome was favorable with cessation of occupational exposure to the device, without any medication. This is the first report of a case of HP in a beautician due to steam contaminated by Pseudomonas sp. from a vapozone. HP, and not only asthma and contact dermatitis, should be suspected in beauticians with respiratory symptoms. Am. J. Ind. Med. 59:1041-1045, 2016. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Laboratory investigations of steam flow in a porous medium

USGS Publications Warehouse

Herkelrath, W.N.; Moench, A.F.; O'Neal, II

1983-01-01

Experiments were carried out in the laboratory to test a theory of transient flow of pure steam in a uniform porous medium. This theory is used in modeling pressure transient behavior in vapor dominated geothermal systems. Transient, superheated steam flow experiments were run by bringing a cylinder of porous material to a uniform initial pressure and then making a step increase in pressure at one end of the sample while monitoring the pressure transient breakthrough at the other end. It was found in experiments run at 100°, 125°, and 146°C that the time required for steam pressure transients to propagate through an unconsolidated material containing sand, silt, and clay was 10–25 times longer than predicted by conventional superheated steam flow theory. It is hypothesized that the delay in the steam pressure transient was caused by adsorption of steam in the porous sample. In order to account for steam adsorption, a sink term was included in the conservation of mass equation. In addition, energy transfer in the system has to be considered because latent heat is released when steam adsorption occurs, increasing the sample temperature by as much as 10°C. Finally, it was recognized that the steam pressure was a function of both the temperature and the amount of adsorption in the sample. This function was assumed to be an equilibrium adsorption isotherm, which was determined by experiment. By solving the modified mass and energy equations numerically, subject to the empirical adsorption isotherm relationship, excellent theoretical simulation of the experiments was achieved.

Dynamic underground stripping: steam and electric heating for in situ decontamination of soils and groundwater

DOEpatents

Daily, W.D.; Ramirez, A.L.; Newmark, R.L.; Udell, K.; Buetnner, H.M.; Aines, R.D.

1995-09-12

A dynamic underground stripping process removes localized underground volatile organic compounds from heterogeneous soils and rock in a relatively short time. This method uses steam injection and electrical resistance heating to heat the contaminated underground area to increase the vapor pressure of the contaminants, thus speeding the process of contaminant removal and making the removal more complete. The injected steam passes through the more permeable sediments, distilling the organic contaminants, which are pumped to the surface. Large electrical currents are also applied to the contaminated area, which heat the impermeable subsurface layers that the steam has not penetrated. The condensed and vaporized contaminants are withdrawn by liquid pumping and vacuum extraction. The steam injection and electrical heating steps are repeated as necessary. Geophysical imaging methods can be used to map the boundary between the hot, dry, contamination-free underground zone and the cool, damp surrounding areas to help monitor the dynamic stripping process. 4 figs.

Dynamic underground stripping: steam and electric heating for in situ decontamination of soils and groundwater

DOEpatents

Daily, William D.; Ramirez, Abelardo L.; Newmark, Robin L.; Udell, Kent; Buetnner, Harley M.; Aines, Roger D.

1995-01-01

A dynamic underground stripping process removes localized underground volatile organic compounds from heterogeneous soils and rock in a relatively short time. This method uses steam injection and electrical resistance heating to heat the contaminated underground area to increase the vapor pressure of the contaminants, thus speeding the process of contaminant removal and making the removal more complete. The injected steam passes through the more permeable sediments, distilling the organic contaminants, which are pumped to the surface. Large electrical currents are also applied to the contaminated area, which heat the impermeable subsurface layers that the steam has not penetrated. The condensed and vaporized contaminants are withdrawn by liquid pumping and vacuum extraction. The steam injection and electrical heating steps are repeated as necessary. Geophysical imaging methods can be used to map the boundary between the hot, dry, contamination-free underground zone and the cool, damp surrounding areas to help monitor the dynamic stripping process.

An innovative modular device and wireless control system enabling thermal and pressure sensors using FPGA on real-time fault diagnostics of steam turbine functional deterioration

NASA Astrophysics Data System (ADS)

Devi, S.; Saravanan, M.

2018-03-01

It is necessary that the condition of the steam turbines is continuously monitored on a scheduled basis for the safe operation of the steam turbines. The review showed that steam turbine fault detection and operation maintenance system (STFDOMS) is gaining importance recently. In this paper, novel hardware architecture is proposed for STFDOMS that can be communicated through the GSM network. Arduino is interfaced with the FPGA so as to transfer the message. The design has been simulated using the Verilog programming language and implemented in hardware using FPGA. The proposed system is shown to be a simple, cost effective and flexible and thereby making it suitable for the maintenance of steam turbines. This system forewarns the experts to access to data messages and take necessary action in a short period with great accuracy. The hardware developed is promised as a real-time test bench, specifically for investigations of long haul effects with different parameter settings.

Colored Sticky Traps to Selectively Survey Thrips in Cowpea Ecosystem.

PubMed

Tang, L D; Zhao, H Y; Fu, B L; Han, Y; Liu, K; Wu, J H

2016-02-01

The bean flower thrips, Megalurothrips usitatus (Bagrall) (Thysanoptera: Thripidae), is an important pest of legume crops in South China. Yellow, blue, or white sticky traps are currently recommended for monitoring and controlling thrips, but it is not known whether one is more efficient than the other or if selectivity could be optimized by trap color. We investigated the response of thrips and beneficial insects to different-colored sticky traps on cowpea, Vigna unguiculata. More thrips were caught on blue, light blue, white, and purple traps than on yellow, green, pink, gray, red, or black traps. There was a weak correlation on the number of thrips caught on yellow traps and survey from flowers (r = 0.139), whereas a strong correlation was found for blue traps and thrips' survey on flowers (r = 0.929). On commercially available sticky traps (Jiaduo®), two and five times more thrips were caught on blue traps than on white and yellow traps, respectively. Otherwise, capture of beneficial insects was 1.7 times higher on yellow than on blue traps. The major natural enemies were the predatory ladybird beetles (63%) and pirate bugs Orius spp. (29%), followed by a number of less representative predators and parasitoids (8%). We conclude the blue sticky trap was the best to monitor thrips on cowpea in South China.

Evaluation of Trap Designs and Deployment Strategies for Capturing Halyomorpha halys (Hemiptera: Pentatomidae)

PubMed Central

Morrison, William R.; Cullum, John P.; Leskey, Tracy C.

2015-01-01

Halyomorpha halys (Stål) is an invasive pest that attacks numerous crops. For growers to make informed management decisions against H. halys, an effective monitoring tool must be in place. We evaluated various trap designs baited with the two-component aggregation pheromone of H. halys and synergist and deployed in commercial apple orchards. We compared our current experimental standard trap, a black plywood pyramid trap 1.22 m in height deployed between border row apple trees with other trap designs for two growing seasons. These included a black lightweight coroplast pyramid trap of similar dimension, a smaller (29 cm) pyramid trap also ground deployed, a smaller limb-attached pyramid trap, a smaller pyramid trap hanging from a horizontal branch, and a semipyramid design known as the Rescue trap. We found that the coroplast pyramid was the most sensitive, capturing more adults than all other trap designs including our experimental standard. Smaller pyramid traps performed equally in adult captures to our experimental standard, though nymphal captures were statistically lower for the hanging traps. Experimental standard plywood and coroplast pyramid trap correlations were strong, suggesting that standard plywood pyramid traps could be replaced with lighter, cheaper coroplast pyramid traps. Strong correlations with small ground- and limb-deployed pyramid traps also suggest that these designs offer promise as well. Growers may be able to adopt alternative trap designs that are cheaper, lighter, and easier to deploy to monitor H. halys in orchards without a significant loss in sensitivity. PMID:26470309

Non-destructive measurement and role of surface residual stress monitoring in residual life assessment of a steam turbine blading material

NASA Astrophysics Data System (ADS)

Prabhu-Gaunkar, Gajanana; Rawat, M. S.; Prasad, C. R.

2014-02-01

Steam turbine blades in power generation equipment are made from martensitic stainless steels having high strength, good toughness and corrosion resistance. However, these steels are susceptible to pitting which can promote early failures of blades in the turbines, particularly in the low pressure dry/wet areas by stress corrosion and corrosion fatigue. Presence of tensile residual stresses is known to accelerate failures whereas compressive stresses can help in delaying failures. Shot peening has been employed as an effective tool to induce compressive residual stresses which offset a part of local surface tensile stresses in the surface layers of components. Maintaining local stresses at stress raisers, such as pits formed during service, below a threshold level can help in preventing the initiation microcracks and failures. The thickness of the layer in compression will, however, depend of the shot peening parameters and should extend below the bottom of corrosion pits. The magnitude of surface compressive drops progressively during service exposure and over time the effectiveness of shot peening is lost making the material susceptible to micro-crack initiation once again. Measurement and monitoring of surface residual stress therefore becomes important for assessing residual life of components in service. This paper shows the applicability of surface stress monitoring to life assessment of steam turbine blade material based on data generated in laboratory on residual surface stress measurements in relation to fatigue exposure. An empirical model is proposed to calculate the remaining life of shot peened steam turbine blades in service.

Cost-Effective Large-Scale Occupancy–Abundance Monitoring of Invasive Brushtail Possums (Trichosurus Vulpecula) on New Zealand’s Public Conservation Land

PubMed Central

Gormley, Andrew M.; Forsyth, David M.; Wright, Elaine F.; Lyall, John; Elliott, Mike; Martini, Mark; Kappers, Benno; Perry, Mike; McKay, Meredith

2015-01-01

There is interest in large-scale and unbiased monitoring of biodiversity status and trend, but there are few published examples of such monitoring being implemented. The New Zealand Department of Conservation is implementing a monitoring program that involves sampling selected biota at the vertices of an 8-km grid superimposed over the 8.6 million hectares of public conservation land that it manages. The introduced brushtail possum (Trichosurus Vulpecula) is a major threat to some biota and is one taxon that they wish to monitor and report on. A pilot study revealed that the traditional method of monitoring possums using leg-hold traps set for two nights, termed the Trap Catch Index, was a constraint on the cost and logistical feasibility of the monitoring program. A phased implementation of the monitoring program was therefore conducted to collect data for evaluating the trade-off between possum occupancy–abundance estimates and the costs of sampling for one night rather than two nights. Reducing trapping effort from two nights to one night along four trap-lines reduced the estimated costs of monitoring by 5.8% due to savings in labour, food and allowances; it had a negligible effect on estimated national possum occupancy but resulted in slightly higher and less precise estimates of relative possum abundance. Monitoring possums for one night rather than two nights would provide an annual saving of NZ$72,400, with 271 fewer field days required for sampling. Possums occupied 60% (95% credible interval; 53–68) of sampling locations on New Zealand’s public conservation land, with a mean relative abundance (Trap Catch Index) of 2.7% (2.0–3.5). Possum occupancy and abundance were higher in forest than in non-forest habitats. Our case study illustrates the need to evaluate relationships between sampling design, cost, and occupancy–abundance estimates when designing and implementing large-scale occupancy–abundance monitoring programs. PMID:26029890

TC-99 Decontaminant from heat treated gaseous diffusion membrane -Phase I, Part B

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oji, L.; Restivo, M.; Duignan, M.

2017-11-01

Uranium gaseous diffusion cascades represent a significant environmental challenge to dismantle, containerize and dispose as low-level radioactive waste. Baseline technologies rely on manual manipulations involving direct access to technetium-contaminated piping and materials. There is a potential to utilize novel decontamination technologies to remove the technetium and allow for on-site disposal of the very large uranium converters. Technetium entered these gaseous diffusion cascades as a hexafluoride complex in the same fashion as uranium. Technetium, as the isotope Tc-99, is an impurity that follows uranium in the first cycle of the Plutonium and Uranium Extraction (PUREX) process. The technetium speciation or exactmore » form in the gaseous diffusion cascades is not well defined. Several forms of Tc-99 compounds, mostly the fluorinated technetium compounds with varying degrees of volatility have been speculated by the scientific community to be present in these cascades. Therefore, there may be a possibility of using thermal or leaching desorption, which is independent of the technetium oxidation states, to perform an insitu removal of the technetium as a volatile species and trap the radionuclide on sorbent traps which could be disposed as low-level waste. Based on the positive results of the first part of this work1 the use of steam as a thermal decontamination agent was further explored with a second piece of used barrier material from a different location. This new series of tests included exposing more of the material surface to the flow of high temperature steam through the change in the reactor design, subjecting it to alternating periods of stream and vacuum, as well as determining if a lower temperature steam, i.e., 121°C (250°F) would be effective, too. Along with these methods, one other simpler method involving the leaching of the Tc-99 contaminated barrier material with a 1.0 M aqueous solution of ammonium carbonate, with and without sonication, was evaluated.« less

Criteria for personal dosimetry in mixed radiation fields in space. [analyzing trapped protons, tissue disintegration stars, and neutrons

NASA Technical Reports Server (NTRS)

Schaefer, H. J.

1974-01-01

The complexity of direct reading and passive dosimeters for monitoring radiation is studied to strike the right balance of compromise to simplify the monitoring procedure. Trapped protons, tissue disintegration stars, and neutrons are analyzed.

Post-Closure Monitoring Report for Corrective Action Unit 339: Area 12 Fleet Operations Steam Cleaning Effluent Nevada Test Site, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

K. B. Campbell

2002-09-01

The Area 12 Fleet Operations Steam Cleaning Effluent site is located in the southeastern portion of the Area 12 Camp at the Nevada Test Site. This site is identified in the Federal Facility Agreement and Consent Order (1996) as Corrective Action Site (CAS) 12-19-01 and is the only CAS assigned to Corrective Action Unit (CAU) 339. Post-closure sampling and inspection of the site were completed on March 27, 2002. Post-closure monitoring activities were scheduled biennially (every two years) in the Post-Closure Monitoring Plan provided in the Closure Report for CAU 339: Area 12 Fleet Operations Steam Cleaning Effluent, Nevada Testmore » Site (U.S. Department of Energy, Nevada Operations Office [DOEN], 1997). A baseline for the site was established by sampling in 1997. Based on the recommendations from the 1999 post-closure monitoring report (DOE/NV, 1999), samples were collected in 2000, earlier than originally proposed, because the 1999 sample results did not provide the expected decrease in total petroleum hydrocarbon (TPH) concentrations at the site. Sampling results from 2000 (DOE/NV, 2000) and 2001 (DOE/NV, 2001) revealed favorable conditions for natural degradation at the CAU 339 site, but because of differing sample methods and heterogeneity of the soil, data results from 2000 and later were not directly correlated with previous results. Post-closure monitoring activities for 2002 consisted of the following: (1) Soil sample collection from three undisturbed plots (Plots A, B, and C, Figure 2). (2) Sample analysis for TPH as oil and bio-characterization parameters (Comparative Enumeration Assay [CEA] and Standard Nutrient Panel [SNP]). (3) Site inspection to evaluate the condition of the fencing and signs. (4) Preparation and submittal of the Post-Closure Monitoring Report.« less

Sampling bee communities using pan traps: alternative methods increase sample size

USDA-ARS?s Scientific Manuscript database

Monitoring of the status of bee populations and inventories of bee faunas require systematic sampling. Efficiency and ease of implementation has encouraged the use of pan traps to sample bees. Efforts to find an optimal standardized sampling method for pan traps have focused on pan trap color. Th...

40 CFR 63.4168 - What are the requirements for continuous parameter monitoring system installation, operation, and...

Code of Federal Regulations, 2014 CFR

2014-07-01

... add-on control device, you must monitor the total regeneration desorbing gas (e.g., steam or nitrogen) mass flow for each regeneration cycle, the carbon bed temperature after each regeneration and cooling... regeneration desorbing gas mass flow monitor must be an integrating device having a measurement sensitivity of...

40 CFR 60.334 - Monitoring of operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... continuous monitoring system to monitor and record the fuel consumption and the ratio of water or steam to...) On a ppm basis (for NOX) and a percent O2 basis for oxygen; or (ii) On a ppm at 15 percent O2 basis... temperature (Ta), and minimum combustor inlet absolute pressure (Po) into the ISO correction equation. (iii...

40 CFR 60.334 - Monitoring of operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... continuous monitoring system to monitor and record the fuel consumption and the ratio of water or steam to...) On a ppm basis (for NOX) and a percent O2 basis for oxygen; or (ii) On a ppm at 15 percent O2 basis... temperature (Ta), and minimum combustor inlet absolute pressure (Po) into the ISO correction equation. (iii...

40 CFR 60.334 - Monitoring of operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... continuous monitoring system to monitor and record the fuel consumption and the ratio of water or steam to...) On a ppm basis (for NOX) and a percent O2 basis for oxygen; or (ii) On a ppm at 15 percent O2 basis... temperature (Ta), and minimum combustor inlet absolute pressure (Po) into the ISO correction equation. (iii...

40 CFR 60.334 - Monitoring of operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... continuous monitoring system to monitor and record the fuel consumption and the ratio of water or steam to...) On a ppm basis (for NOX) and a percent O2 basis for oxygen; or (ii) On a ppm at 15 percent O2 basis... temperature (Ta), and minimum combustor inlet absolute pressure (Po) into the ISO correction equation. (iii...

40 CFR 60.334 - Monitoring of operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... continuous monitoring system to monitor and record the fuel consumption and the ratio of water or steam to...) On a ppm basis (for NOX) and a percent O2 basis for oxygen; or (ii) On a ppm at 15 percent O2 basis... temperature (Ta), and minimum combustor inlet absolute pressure (Po) into the ISO correction equation. (iii...

Intercept™ Panel Trap (INT PT) effective in management of forest Coleoptera

Treesearch

D. Czokajlo; J. McLaughlin; L. I. Abu Ayyash; S. Teale; J. Wickham; J. Warren; R. Hoffman; B. Aukema; K. Raffa; P. Kirsch

2003-01-01

Trap efficacy in capturing economically important forest Coleoptera was measured in field trials comparing the Intercept Panel Trap (INT PT) with the Multi-Funnel Trap. The INT PT was designed to provide a better option for the monitoring of forest Coleoptera. The trap is made of corrugated plastic and is very robust under rigorous field conditions, but still...

Monitoring Pest Insect Traps by Means of Low-Power Image Sensor Technologies

PubMed Central

López, Otoniel; Rach, Miguel Martinez; Migallon, Hector; Malumbres, Manuel P.; Bonastre, Alberto; Serrano, Juan J.

2012-01-01

Monitoring pest insect populations is currently a key issue in agriculture and forestry protection. At the farm level, human operators typically must perform periodical surveys of the traps disseminated through the field. This is a labor-, time- and cost-consuming activity, in particular for large plantations or large forestry areas, so it would be of great advantage to have an affordable system capable of doing this task automatically in an accurate and a more efficient way. This paper proposes an autonomous monitoring system based on a low-cost image sensor that it is able to capture and send images of the trap contents to a remote control station with the periodicity demanded by the trapping application. Our autonomous monitoring system will be able to cover large areas with very low energy consumption. This issue would be the main key point in our study; since the operational live of the overall monitoring system should be extended to months of continuous operation without any kind of maintenance (i.e., battery replacement). The images delivered by image sensors would be time-stamped and processed in the control station to get the number of individuals found at each trap. All the information would be conveniently stored at the control station, and accessible via Internet by means of available network services at control station (WiFi, WiMax, 3G/4G, etc.). PMID:23202232

Monitoring pest insect traps by means of low-power image sensor technologies.

PubMed

López, Otoniel; Rach, Miguel Martinez; Migallon, Hector; Malumbres, Manuel P; Bonastre, Alberto; Serrano, Juan J

2012-11-13

Monitoring pest insect populations is currently a key issue in agriculture and forestry protection. At the farm level, human operators typically must perform periodical surveys of the traps disseminated through the field. This is a labor-, time- and cost-consuming activity, in particular for large plantations or large forestry areas, so it would be of great advantage to have an affordable system capable of doing this task automatically in an accurate and a more efficient way. This paper proposes an autonomous monitoring system based on a low-cost image sensor that it is able to capture and send images of the trap contents to a remote control station with the periodicity demanded by the trapping application. Our autonomous monitoring system will be able to cover large areas with very low energy consumption. This issue would be the main key point in our study; since the operational live of the overall monitoring system should be extended to months of continuous operation without any kind of maintenance (i.e., battery replacement). The images delivered by image sensors would be time-stamped and processed in the control station to get the number of individuals found at each trap. All the information would be conveniently stored at the control station, and accessible via Internet by means of available network services at control station (WiFi, WiMax, 3G/4G, etc.).

40 CFR 63.453 - Monitoring requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... outlet total HAP or methanol concentration, as an alternative to monitoring thermal oxidizer operating... operated to measure the methanol outlet concentration to comply with the steam stripper outlet... requirements specified in paragraphs (j)(1)(ii)(A) and (B) of this section. (A) Obtain daily inlet and outlet...

40 CFR 63.453 - Monitoring requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... outlet total HAP or methanol concentration, as an alternative to monitoring thermal oxidizer operating... operated to measure the methanol outlet concentration to comply with the steam stripper outlet... requirements specified in paragraphs (j)(1)(ii)(A) and (B) of this section. (A) Obtain daily inlet and outlet...

Monitoring stink bugs (Hemiptera: Pentatomidae) in mid-Atlantic apple and peach orchards.

PubMed

Leskey, T C; Hogmire, H W

2005-02-01

Pyramid traps coated with "industrial safety yellow" exterior latex gloss enamel paint and baited with Euschistus spp. aggregation pheromone, methyl (2E,4Z)-decadienoate captured more stink bugs than all other baited and unbaited trap types in both apple and peach orchards in 2002 and 2003. Commercial sources of dispensers of methyl (2E,4Z)-decadienoate deployed in association with pyramid traps had a significant impact on trap captures. Captures in pyramid traps were four-fold greater when baited with lures from IPM Technologies, Inc. (Portland, OR) than with lures from Suterra (Bend, OR). Variation in yellow pyramid trap color ("industrial safety yellow" and "standard coroplast yellow") and material (plywood, plastic, and masonite) did not affect trap captures. Brown stink bug was the predominant species captured (58%), followed by dusky stink bug, Euschistus tristigmus (Say) (20%); green stink bug, Acrosternum hilare (Say) (14%); and other stink bugs (Brochymena spp. and unidentified nymphs) (8%). Captures in baited pyramid traps were significantly correlated with tree beating samples in both managed and unmanaged apple orchards and with sweep netting samples in the unmanaged apple orchard. However, problems associated with trapping mechanisms of pyramid trap jar tops and jar traps likely resulted in reduced captures in baited traps. Improved trapping mechanisms must be established to develop an effective monitoring tool for stink bugs in mid-Atlantic orchards.

Combination phenyl propionate/pheromone traps for monitoring navel orangeworm (Lepidoptera: Pyralidae) in almonds in the vicinity of mating disruption

USDA-ARS?s Scientific Manuscript database

Aerosol mating disruption is used for management of navel orangeworm, Amyelois transitella (Walker) (Lepidoptera: Pyralidae), in an increasing portion of California almonds and pistachios. This formulation suppresses pheromone monitoring traps far beyond the treatment block, potentially complicating...

Influence of trap design on upwind flight behavior and capture of female grape berry moth (Lepidoptera: Tortricidae) with a kairomone lure.

PubMed

Cha, Dong H; Hesler, Stephen P; Linn, Charles E; Zhang, Aijun; Teal, Peter E A; Knight, Alan L; Roelofs, Wendell L; Loeb, Gregory M

2013-02-01

Oil-coated clear panel traps baited with a host plant-based kairomone lure have successfully been used for monitoring female grape berry moth, Paralobesia viteana (Clemens) (Lepidoptera: Tortricidae), but low capture rates as well as difficulty in servicing these traps makes them unsuitable for commercial use. We compared the performance of different trap designs in a flight tunnel and in a vineyard by using a 7-component synthetic kairomone blend, with a focus on trap visual cues. In flight tunnel experiments, a clear delta trap performed better than other traps. When we tested clear delta, green delta, or clear wing traps baited with a cut grape shoot, >50% of female grape berry moths made complete upwind flights. However, the clear delta trap was the only design that resulted in female moths entering the trap. Similar results were observed when females were tested with different traps (clear delta, green delta, white delta, clear wing, or green wing traps) baited with the kairomone lure. Adding a visual pattern that mimicked grape shoots to the outside surface of the clear delta trap resulted in 66% of the females that made upwind flights entering the trap. However, the positive effect of adding a visual pattern to the trap was not observed in a vineyard setting, where clear delta traps with or without a visual pattern caught similar numbers of females. Still, the number of male and female grape berry moths captured in clear delta traps with or without a visual pattern was not significantly different from the number of male and female grape berry moths captured in panel traps, suggesting that the use of these delta traps could be a less cumbersome alternative to oil-coated panel traps for monitoring female grape berry moth.

Steam explosions, earthquakes, and volcanic eruptions -- what's in Yellowstone's future?

USGS Publications Warehouse

Lowenstern, Jacob B.; Christiansen, Robert L.; Smith, Robert B.; Morgan, Lisa A.; Heasler, Henry

2005-01-01

Yellowstone, one of the world?s largest active volcanic systems, has produced several giant volcanic eruptions in the past few million years, as well as many smaller eruptions and steam explosions. Although no eruptions of lava or volcanic ash have occurred for many thousands of years, future eruptions are likely. In the next few hundred years, hazards will most probably be limited to ongoing geyser and hot-spring activity, occasional steam explosions, and moderate to large earthquakes. To better understand Yellowstone?s volcano and earthquake hazards and to help protect the public, the U.S. Geological Survey, the University of Utah, and Yellowstone National Park formed the Yellowstone Volcano Observatory, which continuously monitors activity in the region.

Simple and Efficient Trap for Bark and Ambrosia Beetles (Coleoptera: Curculionidae) to Facilitate Invasive Species Monitoring and Citizen Involvement.

PubMed

Steininger, M S; Hulcr, J; Šigut, M; Lucky, A

2015-06-01

Bark and ambrosia beetles (Coleoptera: Curculionidae: Scolytinae & Platypodinae) are among the most damaging forest pests worldwide, and monitoring is essential to damage prevention. Unfortunately, traps and attractants that are currently used are costly, and agencies rely on limited field personnel for deployment. The situation can be greatly aided by 1) the development of cost-effective trapping techniques, and 2) distribution of the effort through the Citizen Science approach. The goal of this study was to test a simple, effective trap that can be made and deployed by anyone interested in collecting bark and ambrosia beetles. Three trap types made from 2-liter soda bottles and, separately, four attractants were compared. Simple, one-window traps performed comparably at capturing species in traps painted or with multiple windows. A comparison of attractants in two-window traps found that 95% ethanol attracted the highest number of species but that Purell hand sanitizer (70% ethanol) and then Germ-X hand sanitizer (63% ethanol) were also effective. A perforated zip-top plastic bag containing Purell hanging over a trap filled with automobile antifreeze attracted the fewest species and individual specimens. Overall, >4,500 bark and ambrosia beetles, including 30 species were captured, representing a third of the regional species diversity. More than three quarters of the specimens were nonnative, representing nearly half of the known regional exotic species. These results suggest that simple one-window soda bottle traps baited with ethanol-based hand sanitizer will be effective and inexpensive tools for large-scale monitoring of bark and ambrosia beetles. © The Authors 2015. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Effectiveness of different types of hair traps for brown bear research and monitoring

PubMed Central

Okarma, Henryk; Selva, Nuria

2017-01-01

Non-invasive sampling by hair-trapping is increasingly used worldwide in wildlife research. Despite this rise and the potential of hair samples for ecology and conservation studies, the relative performance of hair collection devices has been rarely tested. Here, we compare the effectiveness of five types of hair traps for brown bears Ursus arctos in the Carpathian Mountains (SE Poland) and test the effects of trap type, season, number of days elapsed since trap installation and trap features on the trapping success in order to provide recommendations for optimal sampling in future studies. The trap types were corral, path-trap, “smola”(beechwood tar) tree-trap, turpentine tree-trap and natural rub. In 2010, we collected 858 hair samples during 2330 inspections of 175 hair traps and found that the most effective traps were smola tree-traps (mean percentage of successful inspections ± SD: 30.2% ± 26.0) and natural rubs (50.8% ± 16.7). Based on this finding, over the following 2 years we focused on 24 smola tree-traps and eight natural rubs. During this long-term survey (2010–2012, 969 inspections, 1322 samples collected) the trapping success increased with time and smola tree-traps achieved similar effectiveness to natural rubs (45.5% ± 29.7 and 45.9 ± 23.4, respectively). We show that when baiting smola tree-traps ten weeks prior to research or monitoring, sampling effectiveness can reach up to 30%. Taking into account the logistical and methodological constraints associated with detecting and using natural rubs for a proper survey design, we recommend using smola tree-traps baited in advance for hair sampling in wildlife studies. PMID:29073161

Effectiveness of different types of hair traps for brown bear research and monitoring.

PubMed

Berezowska-Cnota, Teresa; Luque-Márquez, Ignacio; Elguero-Claramunt, Isabel; Bojarska, Katarzyna; Okarma, Henryk; Selva, Nuria

2017-01-01

Non-invasive sampling by hair-trapping is increasingly used worldwide in wildlife research. Despite this rise and the potential of hair samples for ecology and conservation studies, the relative performance of hair collection devices has been rarely tested. Here, we compare the effectiveness of five types of hair traps for brown bears Ursus arctos in the Carpathian Mountains (SE Poland) and test the effects of trap type, season, number of days elapsed since trap installation and trap features on the trapping success in order to provide recommendations for optimal sampling in future studies. The trap types were corral, path-trap, "smola"(beechwood tar) tree-trap, turpentine tree-trap and natural rub. In 2010, we collected 858 hair samples during 2330 inspections of 175 hair traps and found that the most effective traps were smola tree-traps (mean percentage of successful inspections ± SD: 30.2% ± 26.0) and natural rubs (50.8% ± 16.7). Based on this finding, over the following 2 years we focused on 24 smola tree-traps and eight natural rubs. During this long-term survey (2010-2012, 969 inspections, 1322 samples collected) the trapping success increased with time and smola tree-traps achieved similar effectiveness to natural rubs (45.5% ± 29.7 and 45.9 ± 23.4, respectively). We show that when baiting smola tree-traps ten weeks prior to research or monitoring, sampling effectiveness can reach up to 30%. Taking into account the logistical and methodological constraints associated with detecting and using natural rubs for a proper survey design, we recommend using smola tree-traps baited in advance for hair sampling in wildlife studies.

40 CFR 63.3547 - What are the requirements for continuous parameter monitoring system installation, operation, and...

Code of Federal Regulations, 2012 CFR

2012-07-01

... adsorber as an add-on control device, you must monitor the total regeneration desorbing gas (e.g., steam or nitrogen) mass flow for each regeneration cycle, the carbon bed temperature after each regeneration and... regeneration desorbing gas mass flow monitor must be an integrating device having an accuracy of ±10 percent...

40 CFR 63.3547 - What are the requirements for continuous parameter monitoring system installation, operation, and...

Code of Federal Regulations, 2013 CFR

2013-07-01

... adsorber as an add-on control device, you must monitor the total regeneration desorbing gas (e.g., steam or nitrogen) mass flow for each regeneration cycle, the carbon bed temperature after each regeneration and... regeneration desorbing gas mass flow monitor must be an integrating device having an accuracy of ±10 percent...

40 CFR 63.3547 - What are the requirements for continuous parameter monitoring system installation, operation, and...

Code of Federal Regulations, 2014 CFR

2014-07-01

... adsorber as an add-on control device, you must monitor the total regeneration desorbing gas (e.g., steam or nitrogen) mass flow for each regeneration cycle, the carbon bed temperature after each regeneration and... regeneration desorbing gas mass flow monitor must be an integrating device having an accuracy of ±10 percent...

Monitoring of Cyclic Steam Stimulation by Inversion of Surface Tilt Measurements

NASA Astrophysics Data System (ADS)

Maharramov, M.; Zoback, M. D.

2014-12-01

Temperature and pressure changes associated with the cyclic steam simulation (CSS) used in heavy oil production from sands are accompanied by significant deformation. Inversion of geomechanical data may provide a potentially powerful reservoir monitoring tool where geomechanical effects are significant. Induced pore pressure changes can be inverted from measurable surface deformations by solving an inverse problem of poroelasticity. In this work, we apply this approach to estimating pore pressure changes from surface tilt measurements at a heavy oil reservoir undergoing cyclic steam simulation. Steam was injected from November 2007 through January 2008. Surface tilt measurements were collected from 25 surface tilt stations during this period. The injection ran in two overlapping phases: Phase 1 ran from the beginning of the injection though mid-December, and Phase 2 overlapped with Phase 1 and ran through the beginning of January. During Phase 1 steam was injected in the western part of the reservoir, followed by injection in the eastern part in Phase 2. The pore pressure evolution was inverted from daily tilt measurements using regularized constrained least squares fitting, the results are shown on the plot. Estimated induced pore pressure change (color scale), observed daily incremental tilts (green arrows) and modeled daily incremental tilts (red arrows) are shown in three panels corresponding to two and five weeks of injection, and the end of injection period. DGPS measurements available for a single location were used as an additional inversion constraint. The results indicate that the pore pressure increase in the reservoir follows the same pattern as the steam injection, from west to east. This qualitative behaviour is independent of the amount of regularization, indirectly validating our inversion approach. Patches of lower pressure appear to be stable with regard to regularization and may provide valuable insight into the efficiency of steam injection. Inversion of pore pressure (and surface deformation) from tilts in this case is non-unique, and the DGPS measurement provided an important additional constraint. The method can be applied to inverting pore pressure changes from InSAR observations, and the latter can be expected to reduce limitations due to noise in tilt measurements.

A new attractant for monitoring western flower thrips, Frankliniella occidentalis in protected crops.

PubMed

Abdullah, Zayed S; Greenfield, Bethany Pj; Ficken, Katherine J; Taylor, James Wd; Wood, Martyn; Butt, Tariq M

2015-01-01

Monitoring of pest populations is an essential component of integrated pest management. An early warning system helps growers decide when best to take control measures, or when to alter them, should a control method prove inadequate. Studies have shown that adding chemical attractants to sticky cards can increase trap catch of western flower thrips, Frankliniella occidentalis, a global pest of agriculture and horticulture, giving more accurate accounts of population size and dynamics, thus leading to more efficient monitoring. We identify a novel semiochemical to the species, (S)-(-)-verbenone, showing that addition of this compound to sticky traps significantly increased F. occidentalis catch in two geographically distinct populations, infesting two unrelated crops of global economic importance. We validate through field trials that (S)-(-)-verbenone is highly attractive to F.occidentalis and can be used with blue sticky traps to enhance trap catch, leading to better estimations of pest population densities. The compound may be used in other control methods against F.occidentalis such as lure and kill, mass trapping and push-pull.

An Experimental Evaluation of Cross-Vane Panel Traps for the Collection of Sylvatic Triatomines (Hemiptera: Reduviidae).

PubMed

Updyke, Erin Allmann; Allan, Brian F

2018-02-28

Due to the limited understanding of the sylvatic cycle of Chagas disease transmission, an efficient method to attract and capture sylvatic triatomines (Hemiptera: Reduviidae) is essential to monitor human exposure risk. Current collection methods for sylvatic species, though effective, are labor- and time-intensive. This study evaluated whether modified cross-vane panel traps (commonly used in forest entomology) can be used to attract and capture flying life-stages of sylvatic triatomines and whether a commercially available lure is effective in attracting sylvatic triatomines in the field. We evaluated four trap treatments in both the wet and dry seasons in central Panama: a cross-vane panel trap fitted with an ultraviolet (UV) light, a cross-vane panel trap fitted with a commercially available human-volatile lure, a cross-vane panel trap fitted with both a UV light and a human-volatile lure, and a white sheet fitted with a UV light (a standard collection method) as a control. A total of 45 adult Rhodnius pallescens Barber were captured across 10 nights of trapping representing 112 trap-nights. There was a significant overall effect of trap type on collection success; sheet traps collected more triatomines than lure traps, and there were no differences between the sheet trap and the UV trap, nor between the sheet trap and the UV + lure trap. The lure-only trap did not capture any triatomines in this study. These results indicate that cross-vane panel traps with a UV light are as effective as a sheet trap but offer the advantage of requiring less time and effort to maintain and monitor.

Combination Phenyl Propionate/Pheromone Traps for Monitoring Navel Orangeworm (Lepidoptera: Pyralidae) in Almonds in the Vicinity of Mating Disruption.

PubMed

Burks, Charles S

2017-04-01

Aerosol mating disruption is used for management of navel orangeworm, Amyelois transitella (Walker) (Lepidoptera: Pyralidae), in an increasing portion of California almonds and pistachios. This formulation suppresses pheromone monitoring traps far beyond the treatment block, potentially complicating monitoring and management of this key pest. Phenyl propionate is an attractant used to capture adults in the presence of mating disruption, completely suppressing pheromone traps, and lures combining phenyl propionate with a pheromone lure (PPO-combo lure) synergize trap capture in the presence of mating disruption. In this study, laboratory and field trials of different phenyl propionate dispensers indicate a useful life of six weeks. Controlled experiments found similar numbers of adults captured in phenyl propionate and PPO-combo lures in the presence of varying levels of mating disruption intensity. A subsequent trial compared monitoring of field plots at various distances from fields under commercial mating disruption for much of the growing season with pheromone and PPO-combo lures. Although there was some evidence of partial suppression of capture in PPO-combo traps closer to mating disruption compared with lures farther away, there was no failure of detection as occurred with pheromone lures. The ratio of adults in pheromone and PPO-combo traps varied with proximity from treated fields. These results indicate that, in addition to monitoring in mating disruption plots, phenyl propionate lures can be useful for insuring against failure of detection of navel orangeworm pressure in areas where mating disruption is widely used. Published by Oxford University Press on behalf of Entomological Society of America 2017. This work is written by a US Government employee and is in the public domain in the US.

Laser removal of sludge from steam generators

DOEpatents

Nachbar, Henry D.

1990-01-01

A method of removing unwanted chemical deposits known as sludge from the metal surfaces of steam generators with laser energy is provided. Laser energy of a certain power density, of a critical wavelength and frequency, is intermittently focused on the sludge deposits to vaporize them so that the surfaces are cleaned without affecting the metal surface (sludge substrate). Fiberoptic tubes are utilized for laser beam transmission and beam direction. Fiberoptics are also utilized to monitor laser operation and sludge removal.

Evaluation of traps used to monitor southern pine beetle aerial populations and sex ratios

Treesearch

James T. Cronin; Jane L. Hayes; Peter Turchin

2000-01-01

Various kinds of traps have been employed to monitor and forecast population trends of the southern pine beetle (Dendroctonus frontalis Zimmermann; Coleoptera: Scolytidae), but their accuracy in assessing pine-beetle abundance and sex ratio in the field has not been evaluated directly.In trus study, we...

Diaphorina citri (Hemiptera: Liviidae) responses to microcontroller-buzzer communication signals of potential use in vibration traps

USDA-ARS?s Scientific Manuscript database

Monitoring of Diaphorina citri Kuwayama populations is an important component of efforts to reduce damage caused by huanglongbing, a devastating disease it vectors in citrus groves. Currently, D. citri is monitored primarily by unbaited sticky traps or visual inspection of trees. A potentially more ...

Captures of boll weevils (Coleoptera: Curculionidae) in relation to trap orientation and distance from brush lines

USDA-ARS?s Scientific Manuscript database

Eradication programs for the boll weevil (Anthonomus grandis Boheman) rely on pheromone-baited traps to trigger insecticide treatments and monitor program progress. A key objective of monitoring in these programs is the timely detection of incipient weevil populations to limit or prevent re-infestat...

Comparison of trap types, placement, and colors for monitoring Anthonomus musculus (Coleoptera: Curculionidae) adults in highbush blueberries

USDA-ARS?s Scientific Manuscript database

Cranberry weevil, Anthonomus musculus Say (Coleoptera: Curculionidae), is a key pest of highbush blueberries in the northeast USA. To date, however, no trapping system has been developed to successfully monitor this pest. In 2012-2014, studies were conducted in commercial blueberry farms in New Jers...

Gypsy moth (Lepidoptera: Lymantriidae) flight behavior and phenology based on field-deployed automated pheromone-baited traps

Treesearch

Patrick C. Tobin; Kenneth T. Klein; Donna S. Leonard

2009-01-01

Populations of the gypsy moth, Lymantria dispar (L.), are extensively monitored in the United States through the use of pheromone-baited traps.We report on use of automated pheromone-baited traps that use a recording sensor and data logger to record the unique date-time stamp of males as they enter the trap.We deployed a total of 352 automated traps...

Aggregation pheromones for monitoring the coconut rhinoceros beetle (Oryctes rhinoceros) in Jerukwangi Village, Jepara, Indonesia

NASA Astrophysics Data System (ADS)

Indriyanti, D. R.; Lutfiana, J. E.; Widiyaningrum, P.; Susilowati, E.; Slamet, M.

2018-03-01

Oryctes rhinoceros (Coleoptera: Scarabaeidae) is the most serious pest of coconut plantations in Indonesia. Jerukwangi Village is O. rhinoceros attacked one of the coconuts producing villages with more than 75% of the coconut plant population O. rhinoceros. The study aimed to monitor the population and analyze the sex ratio of O. rhinoceros that were attracted to aggregation pheromones in the field. Aggregation pheromones is a chemical compound containing Ethyl 4-methyl octanoate. The pheromone compounds were placed in traps (buckets), hung 2 meters above the ground. The traps were observed, and the beetles trapped were counted every week. In 12 weeks of monitoring, the traps captured 101 insects consist of 90.1% O. rhinoceros and 9.9% other insect species (Rhynchophorus ferrugineus and Xylotrupes gideon). This result indicates the high population of O. rhinoceros in the field. Aggregation pheromone is useful for attracting females. Rhinoceros by 61% and the males by 39%. The advantage of research is it can be used in integrated pest management (IPM) packages for monitoring of beetle population, and removal of beetles.

40 CFR Table 12 to Subpart G of... - Monitoring Requirements for Treatment Processes

Code of Federal Regulations, 2013 CFR

2013-07-01

... Appropriate methods as specified in § 63.143 and as approved by permitting authority. 2. Steam stripper (i... recorder. (ii) Wastewater feed mass flow rate; and Continuously Liquid flow meter installed at stripper... operating temperature Continuously (A) Liquid temperature monitoring device installed at stripper influent...

40 CFR Table 12 to Subpart G of... - Monitoring Requirements for Treatment Processes

Code of Federal Regulations, 2010 CFR

2010-07-01

... Appropriate methods as specified in § 63.143 and as approved by permitting authority. 2. Steam stripper (i... recorder. (ii) Wastewater feed mass flow rate; and Continuously Liquid flow meter installed at stripper... operating temperature Continuously (A) Liquid temperature monitoring device installed at stripper influent...

40 CFR Table 12 to Subpart G of... - Monitoring Requirements for Treatment Processes

Code of Federal Regulations, 2011 CFR

2011-07-01

... Appropriate methods as specified in § 63.143 and as approved by permitting authority. 2. Steam stripper (i... recorder. (ii) Wastewater feed mass flow rate; and Continuously Liquid flow meter installed at stripper... operating temperature Continuously (A) Liquid temperature monitoring device installed at stripper influent...

40 CFR Table 12 to Subpart G of... - Monitoring Requirements for Treatment Processes

Code of Federal Regulations, 2014 CFR

2014-07-01

... Appropriate methods as specified in § 63.143 and as approved by permitting authority. 2. Steam stripper (i... recorder. (ii) Wastewater feed mass flow rate; and Continuously Liquid flow meter installed at stripper... operating temperature Continuously (A) Liquid temperature monitoring device installed at stripper influent...

40 CFR Table 12 to Subpart G of... - Monitoring Requirements for Treatment Processes

Code of Federal Regulations, 2012 CFR

2012-07-01

... Appropriate methods as specified in § 63.143 and as approved by permitting authority. 2. Steam stripper (i... recorder. (ii) Wastewater feed mass flow rate; and Continuously Liquid flow meter installed at stripper... operating temperature Continuously (A) Liquid temperature monitoring device installed at stripper influent...

Comparison of hoop-net trapping and visual surveys to monitor abundance of the Rio Grande cooter (Pseudemys gorzugi).

PubMed

Mali, Ivana; Duarte, Adam; Forstner, Michael R J

2018-01-01

Abundance estimates play an important part in the regulatory and conservation decision-making process. It is important to correct monitoring data for imperfect detection when using these data to track spatial and temporal variation in abundance, especially in the case of rare and elusive species. This paper presents the first attempt to estimate abundance of the Rio Grande cooter ( Pseudemys gorzugi ) while explicitly considering the detection process. Specifically, in 2016 we monitored this rare species at two sites along the Black River, New Mexico via traditional baited hoop-net traps and less invasive visual surveys to evaluate the efficacy of these two sampling designs. We fitted the Huggins closed-capture estimator to estimate capture probabilities using the trap data and distance sampling models to estimate detection probabilities using the visual survey data. We found that only the visual survey with the highest number of observed turtles resulted in similar abundance estimates to those estimated using the trap data. However, the estimates of abundance from the remaining visual survey data were highly variable and often underestimated abundance relative to the estimates from the trap data. We suspect this pattern is related to changes in the basking behavior of the species and, thus, the availability of turtles to be detected even though all visual surveys were conducted when environmental conditions were similar. Regardless, we found that riverine habitat conditions limited our ability to properly conduct visual surveys at one site. Collectively, this suggests visual surveys may not be an effective sample design for this species in this river system. When analyzing the trap data, we found capture probabilities to be highly variable across sites and between age classes and that recapture probabilities were much lower than initial capture probabilities, highlighting the importance of accounting for detectability when monitoring this species. Although baited hoop-net traps seem to be an effective sampling design, it is important to note that this method required a relatively high trap effort to reliably estimate abundance. This information will be useful when developing a larger-scale, long-term monitoring program for this species of concern.

Nantucket pine tip moth, Rhyacionia Frustrana, lures and traps: What is the optimum combination?

Treesearch

Gary L. DeBarr; J. wayne Brewer; R. Scott Cameron; C. Wayne Berisford

1999-01-01

Pheromone traps are used to monitor flight activity of male Nantucket pine tip moths, Rhyacionia frustrana (Comstock), to initialize spray timing models, determine activity periods, or detect population trends. However, a standardized trapping procedure has not been developed. The relative efficacies of six types of lures and eight commercial pheromone traps were...

Maximizing Information Yield From Pheromone-Baited Monitoring Traps: Estimating Plume Reach, Trapping Radius, and Absolute Density of Cydia pomonella (Lepidoptera: Tortricidae) in Michigan Apple

PubMed Central

Adams, C. G.; Schenker, J. H.; McGhee, P. S.; Gut, L. J.; Brunner, J. F.

2017-01-01

Abstract Novel methods of data analysis were used to interpret codling moth (Cydia pomonella) catch data from central-trap, multiple-release experiments using a standard codlemone-baited monitoring trap in commercial apple orchards not under mating disruption. The main objectives were to determine consistency and reliability for measures of: 1) the trapping radius, composed of the trap’s behaviorally effective plume reach and the maximum dispersive distance of a responder population; and 2) the proportion of the population present in the trapping area that is caught. Two moth release designs were used: 1) moth releases at regular intervals in the four cardinal directions, and 2) evenly distributed moth releases across entire approximately 18-ha orchard blocks using both high and low codling moth populations. For both release designs, at high populations, the mean proportion catch was 0.01, and for the even release of low populations, that value was approximately 0.02. Mean maximum dispersive distance for released codling moth males was approximately 260 m. Behaviorally effective plume reach for the standard codling moth trap was < 5 m, and total trapping area for a single trap was approximately 21 ha. These estimates were consistent across three growing seasons and are supported by extraordinarily high replication for this type of field experiment. Knowing the trapping area and mean proportion caught, catch number per single monitoring trap can be translated into absolute pest density using the equation: males per trapping area = catch per trapping area/proportion caught. Thus, catches of 1, 3, 10, and 30 codling moth males per trap translate to approximately 5, 14, 48, and 143 males/ha, respectively, and reflect equal densities of females, because the codling moth sex ratio is 1:1. Combined with life-table data on codling moth fecundity and mortality, along with data on crop yield per trapping area, this fundamental knowledge of how to interpret catch numbers will enable pest managers to make considerably more precise projections of damage and therefore more precise and reliable decisions on whether insecticide applications are justified. The principles and methods established here for estimating absolute codling moth density may be broadly applicable to pests generally and thereby could set a new standard for integrated pest management decisions based on trapping. PMID:28131989

Continuous monitoring of Mount St. Helens Volcano

USGS Publications Warehouse

Spall, H.

1980-01-01

Day by day monitoring of the Mount St. Helens Volcano. These are four scenarios, very different scenarios, that can occur in a average week at Mount St. Helens. Ranging from eruptions of gas and to steam to eruptions of ash and pyroclastic flows to even calm days. This example of monitoring illustrates the differences from day to day volcanic activities at Mount St. Helens. 

The efficiency of light-emitting diode suction traps for the collection of South African livestock-associated Culicoides species.

PubMed

Venter, G J; Boikanyo, S N B; De Beer, C J

2018-06-28

Culicoides biting midges (Diptera: Ceratopogonidae) are vectors of a range of orbiviruses that cause important veterinary diseases such as bluetongue and African horse sickness. The effective monitoring of Culicoides species diversity and abundance, both at livestock and near potential wildlife hosts, is essential for risk management. The Onderstepoort 220-V ultraviolet (UV) light trap is extensively used for this purpose. Reducing its power requirements by fitting low-energy light-emitting diodes (LEDs) can lead to greater flexibility in monitoring. A comparison of the efficiency of the 220-V Onderstepoort trap (8-W fluorescent UV light) with the efficiency of the 220-V or 12-V Onderstepoort traps fitted with red, white, blue or green LEDs or a 12-V fluorescent Onderstepoort trap demonstrated the 220-V Onderstepoort trap to be the most efficient. All the results showed nulliparous Culicoides imicola Kieffer females to be the dominant grouping. Despite the lower numbers collected, 12-V traps can be used in field situations to determine the most abundant species. © 2018 The Royal Entomological Society.

Trapping spotted wing drosophila, Drosophila suzukii (Matsumura)(Diptera: Drosophilidae) with combinations of vinegar and wine, and acetic acid and ethanol

USDA-ARS?s Scientific Manuscript database

Recommendations for monitoring spotted wing drosophila (SWD) Drosophila suzukii, (Matsumura) are to use either vinegar or wine as a bait for traps. Traps baited with vinegar and traps baited with wine, in field tests in northern Oregon, captured large numbers of male and female SWD flies. Numbers of...

Geothermal hazards - Mercury emission

NASA Technical Reports Server (NTRS)

Siegel, S. M.; Siegel, B. Z.

1975-01-01

Enthusiasm for intensified geothermal exploration may induce many participants to overlook a long-term potential toxicity hazard possibly associated with the tapping of magmatic steam. The association of high atmospheric Hg levels with geothermal activity has been established both in Hawaii and Iceland, and it has been shown that mercury can be introduced into the atmosphere from fumaroles, hot springs, and magmatic sources. These arguments, extended to thallium, selenium, and other hazardous elements, underscore the need for environmental monitoring in conjunction with the delivery of magmatic steam to the surface.

Evaluation of yellow sticky traps for monitoring the population of thrips (Thysanoptera) in a mango orchard.

PubMed

Aliakbarpour, Hamaseh; Rawi, Che Salmah Md

2011-08-01

Populations of several thrips species were estimated using yellow sticky traps in an orchard planted with mango, Mangifera indica L. during the dry and wet seasons beginning in late 2008-2009 on Penang Island, Malaysia. To determine the efficacy of using sticky traps to monitor thrips populations, we compared weekly population estimates on yellow sticky traps with thrips population sizes that were determined (using a CO(2) method) directly from mango panicles. Dispersal distance and direction of thrips movement out of the orchard also were studied using yellow sticky traps placed at three distances from the edge of the orchard in four cardinal directions facing into the orchard. The number of thrips associated with the mango panicles was found to be correlated with the number of thrips collected using the sticky trap method. The number of thrips captured by the traps decreased with increasing distance from the mango orchard in all directions. Density of thrips leaving the orchard was related to the surrounding vegetation. Our results demonstrate that sticky traps have the potential to satisfactorily estimate thrips populations in mango orchards and thus they can be effectively employed as a useful tactic for sampling thrips.

Sulfur removal and comminution of carbonaceous material

DOEpatents

Narain, Nand K.; Ruether, John A.; Smith, Dennis N.

1988-01-01

Finely divided, clean coal or other carbonaceous material is provided by forming a slurry of coarse coal in aqueous alkali solution and heating the slurry under pressure to above the critical conditions of steam. The supercritical fluid penetrates and is trapped in the porosity of the coal as it swells in a thermoplastic condition at elevated temperature. By a sudden, explosive release of pressure the coal is fractured into finely divided particles with release of sulfur-containing gases and minerals. The finely divided coal is recovered from the minerals for use as a clean coal product.

Evaluation of surveillance methods for monitoring house fly abundance and activity on large commercial dairy operations.

PubMed

Gerry, Alec C; Higginbotham, G E; Periera, L N; Lam, A; Shelton, C R

2011-06-01

Relative house fly, Musca domestica L., activity at three large dairies in central California was monitored during the peak fly activity period from June to August 2005 by using spot cards, fly tapes, bait traps, and Alsynite traps. Counts for all monitoring methods were significantly related at two of three dairies; with spot card counts significantly related to fly tape counts recorded the same week, and both spot card counts and fly tape counts significantly related to bait trap counts 1-2 wk later. Mean fly counts differed significantly between dairies, but a significant interaction between dairies sampled and monitoring methods used demonstrates that between-dairy comparisons are unwise. Estimate precision was determined by the coefficient of variability (CV) (or SE/mean). Using a CV = 0.15 as a desired level of estimate precision and assuming an integrate pest management (IPM) action threshold near the peak house fly activity measured by each monitoring method, house fly monitoring at a large dairy would require 12 spot cards placed in midafternoon shaded fly resting sites near cattle or seven bait traps placed in open areas near cattle. Software (FlySpotter; http://ucanr.org/ sites/FlySpotter/download/) using computer vision technology was developed to count fly spots on a scanned image of a spot card to dramatically reduce time invested in monitoring house flies. Counts provided by the FlySpotter software were highly correlated to visual counts. The use of spot cards for monitoring house flies is recommended for dairy IPM programs.

Experimental validation of the AVIVET trap, a tool to quantitatively monitor the dynamics of Dermanyssus gallinae populations in laying hens.

PubMed

Lammers, G A; Bronneberg, R G G; Vernooij, J C M; Stegeman, J A

2017-06-01

Dermanyssus gallinae (D.gallinae) infestation causes economic losses due to impaired health and production of hens and costs of parasite control across the world. Moreover, infestations are associated with reduced welfare of hens and may cause itching in humans. To effectively implement control methods it is crucially important to have high quality information about the D.gallinae populations in poultry houses in space and time. At present no validated tool is available to quantitatively monitor the dynamics of all four stages of D.gallinae (i.e., eggs, larvae, nymphs, and adults) in poultry houses.This article describes the experimental validation of the AVIVET trap, a device to quantitatively monitor dynamics of D.gallinae infestations. We used the device to study D.gallinae in fully equipped cages with two white specific pathogen free Leghorn laying hens experimentally exposed to three different infestation levels of D.gallinae (low to high).The AVIVET trap was successfully able to detect D.gallinae at high (5,000 D.gallinae), medium (2,500 D.gallinae), and low (50 D.gallinae) level of D.gallinae infestation. The linear equation Y = 10∧10∧(0.47 + 1.21X) with Y = log10 (Total number of D.gallinae nymphs and adults) in the cage and X = log10 (Total number of D.gallinae nymphs and adults) in the AVIVET trap explained 93.8% of the variation.The weight of D.gallinae in the AVIVET trap also appears to be a reliable parameter for quantifying D.gallinae infestation in a poultry house. The weight of D.gallinae in the AVIVET trap correlates 99.6% (P < 0.000) to the counted number of all stages of D.gallinae in the trap (i.e., eggs, larvae, nymphs, and adults) indicating that the trap is highly specific.From this experiment it can be concluded that the AVIVET trap is promising as quantitative tool for monitoring D.gallinae dynamics in a poultry house. © 2016 Poultry Science Association Inc.

Economic and Highly Effective Trap-Lure Combination to Monitor the Mexican Fruit Fly (Diptera: Tephritidae) at the Orchard Level.

PubMed

Lasa, R; Herrera, F; Miranda, E; Gómez, E; Antonio, S; Aluja, M

2015-08-01

Monitoring population levels of the Mexican fruit fly, Anastrepha ludens (Loew) (Diptera: Tephritidae), at the orchard level prior and during the fruit ripening period can result in significant savings in the costs of managing this pestiferous insect. Unfortunately, to date, no highly effective and economically viable trap is available to growers. To move toward this goal, trap-lure combinations were evaluated in trials performed in citrus orchards in Veracruz, Mexico. CeraTrap, an enzymatic hydrolyzed protein from pig intestinal mucose, was 3.6 times more attractive to A. ludens than the most commonly used bait of Captor (hydrolyzed protein and borax) when using Multilure traps. When several commercial traps were evaluated, the efficacy of a simple and inexpensive transparent polyethylene (PET) bottle with 10-mm lateral holes was similar to that of the costly Multilure trap when baited with CeraTrap and significantly more effective than a Multilure trap baited with Captor. PET bottles filled with Cera Trap, rebaited at 8-wk intervals, and tested in trials encompassing 72 ha of citrus groves, were significantly more effective than Multilure traps baited with Captor that need to be serviced weekly. In addition to this relevant finding, CeraTrap baited traps detected A. ludens at lower population densities and attracted a significantly higher number of flies at all densities when compared with Captor-baited traps. We conclude that CeraTrap represents a cost-effective and highly efficient bait that will enable us to pursue the goal of developing economic thresholds, a badly needed management tool for A. ludens. © The Authors 2015. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Evaluation of methyl eugenol and cue-lure traps with solid lure and insecticide dispensers for fruit fly monitoring and male annihilation in the Hawaii Areawide Pest Management Program.

PubMed

Vargas, Roger I; Mau, Ronald F L; Stark, John D; Piñero, Jaime C; Leblanc, Luc; Souder, Steven K

2010-04-01

Methyl eugenol (ME) and cue-lure (C-L) traps with solid lure dispensers were deployed in areas with low and high populations of oriental fruit fly, Bactrocera dorsalis (Hendel), and melon fly, Bactrocera cucurbitae (Coquillett), respectively. In low-density areas, standard Jackson traps or Hawaii Fruit Fly Areawide Pest Management (AWPM) traps with FT Mallet ME wafers impregnated with dimethyl dichloro-vinyl phosphate (DDVP) or AWPM traps with Scentry ME cones and vapor tape performed equally as well as standard Jackson traps with liquid ME/C-L and naled. Standard Jackson traps or AWPM traps with FT Mallet C-L wafers impregnated with DDVP or AWPM traps with Scentry C-L plugs with vapor tape performed equally as well as standard Jackson traps with a lure-naled solution. In high density areas, captures with traps containing FT Mallet wafers (ME and C-L) outperformed AWPM traps with Scentry cones and plugs (ME and C-L) with DDVP insecticidal strips over a 6-mo period. Captures of B. dorsalis and B. cucurbitae with wafers containing both ME and raspberry ketone (FT Mallet MC) were equivalent to those containing separate lures. From a worker safety and convenience standpoint, FT Mallet ME and C-L wafers with DDVP or Scentry plugs, with or without DDVP vapor tape, are more convenient and safer to handle than standard liquid insecticide formulations used for monitoring and male annihilation programs in Hawaii, and for detections traps used on the U.S. mainland. Furthermore, the FT Mallet MC wafer might be used in a single trap in place of two separate traps for detection of both ME and C-L responding fruit flies.

Application of displacement monitoring system on high temperature steam pipe

NASA Astrophysics Data System (ADS)

Ghaffar, M. H. A.; Husin, S.; Baek, J. E.

2017-10-01

High-energy piping systems of power plants such as Main Steam (MS) pipe or Hot Reheat (HR) pipe are operating at high temperature and high pressure at base and cyclic loads. In the event of transient condition, a pipe can be deflected dramatically and caused high stress in the pipe, yielding to failure of the piping system. Periodic monitoring and walk down can identify abnormalities but limitations exist in the standard walk down practice. This paper provides a study of pipe displacement monitoring on MS pipe of coal-fired power plant to continuously capture the pipe movement behaviour at different load using 3-Dimensional Displacement Measuring System (3DDMS). The displacement trending at Location 5 and 6 (north and south) demonstrated pipes displace less than 25% to that of design movement. It was determined from synchronisation analysis that Location 7 (north) and Location 8 (south) pipe actual movement difference has exceeded the design movement difference. Visual survey at specified locations with significant displacement trending reveals issues of hydraulic snubber and piping interferences. The study demonstrated that the displacement monitoring is able to capture pipe movement at all time and allows engineer to monitor pipe movement behaviour, aids in identifying issue early for remedy action.

Inactivation of Mold Spores from Moist Carpet Using Steam Vapor: Contact Time and Temperature.

PubMed

Ong, Kee-Hean; Emo, Brett; Lewis, Roger D; Kennedy, Jason; Thummalakunta, Laxmi N A; Elliott, Michael

2015-01-01

Steam vapor has been shown to reduce viable mold spores in carpet, but the minimal effective temperature and contact time has not been established. This study evaluated the effectiveness of steam vapor in reducing the number of viable mold spores in carpet as a function of temperature and contact time. Seventy carpet samples were inoculated with a liquid suspension of Cladosporium sphaerospermum and incubated over a water-saturated foam carpet pad for 24 hr. Steam was applied to the samples as the temperature was measured from the carpet backing. Contact time was closely monitored over seven time intervals: 0, 2, 4, 8, 12, 16, and 20 sec. Following steam vapor treatment, mold spores were extracted from the carpet samples and the extract was plated on DG-18 plates at 1:1, 1:10, 1:100 dilutions followed by one week of incubation. Raw colony forming units were determined using an automated colony counter and adjusted based on dilution factor, extraction volume, and plated volume. Analysis of variance and linear regression were used to test for statistically significant relationships. Steam contact time exhibited a linear relationship to observed temperature of carpet backing (F = 90.176, R(2) = 0.609). Observed temperature of carpet backing had a positive relationship to percent reduction of mold (F = 76.605, R(2) = 0.569). Twelve seconds of steam vapor contact time was needed to achieve over 90% mold reduction on moist carpet.

Signal Processing for Determining Water Height in Steam Pipes with Dynamic Surface Conditions

NASA Technical Reports Server (NTRS)

Lih, Shyh-Shiuh; Lee, Hyeong Jae; Bar-Cohen, Yoseph

2015-01-01

An enhanced signal processing method based on the filtered Hilbert envelope of the auto-correlation function of the wave signal has been developed to monitor the height of condensed water through the steel wall of steam pipes with dynamic surface conditions. The developed signal processing algorithm can also be used to estimate the thickness of the pipe to determine the cut-off frequency for the low pass filter frequency of the Hilbert Envelope. Testing and analysis results by using the developed technique for dynamic surface conditions are presented. A multiple array of transducers setup and methodology are proposed for both the pulse-echo and pitch-catch signals to monitor the fluctuation of the water height due to disturbance, water flow, and other anomaly conditions.

Physiological Monitoring of Optically Trapped Cells: Studying the Effects of Confinement by 1064 NM Lazer Tweezers Using Microfluorometry

NASA Astrophysics Data System (ADS)

Liu, Yagang

A novel technique that combines microfluorometric detection and optical laser trapping has been developed for in-situ assessing the physiological state of an optically trapped biological sample. This optical diagnostic technique achieves high sensitivity (>30 dB signal -to-noise ratio) and high spatial resolution (~ 1 μm) over a broad spectral range (>400 nm). The fluorescence spectra derived from exogenous fluorescent probes, including laurdan, acridine orange, propidium iodide and Snarf, are used to assess the effects of optical confinement with respect to temperature, DNA structure, cell viability, and intracellular pH, respectively. In the latter three cases, fluorescence is excited via a two-photon absorption process, using the cw laser trap itself as the fluorescence excitation source. This enables the cw near infrared laser trapping beam to be used simultaneously as an optical diagnostic probe as well as an optical micromanipulator. Using microfluorometry, a temperature increase of less than several degrees centigrade was measured for test samples, including liposomes, Chinese hamster ovary (CHO) cells and human sperm cells that were held stationary by 1064 nm optical tweezers having a power density of ~10^7 W/cm^2. Additional physiological monitoring experiments indicated that there is no observable denaturation of DNA, or change of intracellular pH under typical continuous wave laser trapping conditions (P <= 400 mW). Under some circumstances, however, it was possible to achieve a decrease in cell viability with cw trapping, as monitored by a live/dead vital stain. In comparison, significant DNA denaturation and cellular physiological changes (e.g. cell death) were observed when a Q-switched pulsed laser at a threshold of ~30mu J/pulse was used as trapping source. These results generally support the conclusion that cw laser trapping at 1064 nm wavelength is a safe, non-invasive process and should prove to be of great value for understanding the mechanisms of laser microirradiation effects on living cells held stationary in a near-infrared trapping beam.

Monitoring and Detecting the Cigarette Beetle (Coleoptera: Anobiidae) Using Ultraviolet (LED) Direct and Reflected Lights and/or Pheromone Traps in a Laboratory and a Storehouse.

PubMed

Miyatake, Takahisa; Yokoi, Tomoyuki; Fuchikawa, Taro; Korehisa, Nobuyoshi; Kamura, Toru; Nanba, Kana; Ryouji, Shinsuke; Kamioka, Nagisa; Hironaka, Mantaro; Osada, Midori; Hariyama, Takahiko; Sasaki, Rikiya; Shinoda, Kazutaka

2016-12-01

The cigarette beetle, Lasioderma serricorne (F.), is an important stored-product pest worldwide because it damages dry foods. Detection and removal of the female L. serricorne will help to facilitate the control of the insect by removal of the egg-laying populations. In this manuscript, we examined the responses by L. serricorne to direct and reflected light in transparent cube (50 m3) set in a chamber (200 m3) and a stored facility with both direct and reflected UV-LED lights. The study also examined the responses by the beetles to light in the presence or absence of pheromone in traps that are placed at different heights. Reflected light attracted more beetles than the direct light in the experimental chamber, but the direct light traps attracted more beetles than the reflected light traps in the storehouse. Pheromone traps attracted only males; UV-LED traps attracted both sexes. The UV-LED traps with a pheromone, i.e., combined trap, attracted more males than UV-LED light traps without a pheromone, whereas the attraction of UV-LED traps with and without the pheromone was similar in females. The results suggest that UV-LED light trap combined with a sex pheromone is the best solution for monitoring and controlling L. serricorne. © The Authors 2016. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

A novel mobile monitoring approach to characterize spatial and temporal variation in traffic-related air pollutants in an urban community

NASA Astrophysics Data System (ADS)

Yu, Chang Ho; Fan, Zhihua; Lioy, Paul J.; Baptista, Ana; Greenberg, Molly; Laumbach, Robert J.

2016-09-01

Air concentrations of traffic-related air pollutants (TRAPs) vary in space and time within urban communities, presenting challenges for estimating human exposure and potential health effects. Conventional stationary monitoring stations/networks cannot effectively capture spatial characteristics. Alternatively, mobile monitoring approaches became popular to measure TRAPs along roadways or roadsides. However, these linear mobile monitoring approaches cannot thoroughly distinguish spatial variability from temporal variations in monitored TRAP concentrations. In this study, we used a novel mobile monitoring approach to simultaneously characterize spatial/temporal variations in roadside concentrations of TRAPs in urban settings. We evaluated the effectiveness of this mobile monitoring approach by performing concurrent measurements along two parallel paths perpendicular to a major roadway and/or along heavily trafficked roads at very narrow scale (one block away each other) within short time period (<30 min) in an urban community. Based on traffic and particulate matter (PM) source information, we selected 4 neighborhoods to study. The sampling activities utilized real-time monitors, including battery-operated PM2.5 monitor (SidePak), condensation particle counter (CPC 3007), black carbon (BC) monitor (Micro-Aethalometer), carbon monoxide (CO) monitor (Langan T15), and portable temperature/humidity data logger (HOBO U12), and a GPS-based tracker (Trackstick). Sampling was conducted for ∼3 h in the morning (7:30-10:30) in 7 separate days in March/April and 6 days in May/June 2012. Two simultaneous samplings were made at 5 spatially-distributed locations on parallel roads, usually distant one block each other, in each neighborhood. The 5-min averaged BC concentrations (AVG ± SD, [range]) were 2.53 ± 2.47 [0.09-16.3] μg/m3, particle number concentrations (PNC) were 33,330 ± 23,451 [2512-159,130] particles/cm3, PM2.5 mass concentrations were 8.87 ± 7.65 [0.27-46.5] μg/m3, and CO concentrations were 1.22 ± 0.60 [0.22-6.29] ppm in the community. The traffic-related air pollutants, BC and PNC, but not PM2.5 or CO, varied spatially depending on proximity to local stationary/mobile sources. Seasonal differences were observed for all four TRAPs, significantly higher in colder months than in warmer months. The coefficients of variation (CVs) in concurrent measurements from two parallel routes were calculated around 0.21 ± 0.17, and variations were attributed by meteorological variation (25%), temporal variability (19%), concentration level (6%), and spatial variability (2%), respectively. Overall study findings suggest this mobile monitoring approach could effectively capture and distinguish spatial/temporal characteristics in TRAP concentrations for communities impacted by heavy motor vehicle traffic and mixed urban air pollution sources.

Improvement of Steam Turbine Operational Performance and Reliability with using Modern Information Technologies

NASA Astrophysics Data System (ADS)

Brezgin, V. I.; Brodov, Yu M.; Kultishev, A. Yu

2017-11-01

The report presents improvement methods review in the fields of the steam turbine units design and operation based on modern information technologies application. In accordance with the life cycle methodology support, a conceptual model of the information support system during life cycle main stages (LC) of steam turbine unit is suggested. A classifying system, which ensures the creation of sustainable information links between the engineer team (manufacture’s plant) and customer organizations (power plants), is proposed. Within report, the principle of parameterization expansion beyond the geometric constructions at the design and improvement process of steam turbine unit equipment is proposed, studied and justified. The report presents the steam turbine unit equipment design methodology based on the brand new oil-cooler design system that have been developed and implemented by authors. This design system combines the construction subsystem, which is characterized by extensive usage of family tables and templates, and computation subsystem, which includes a methodology for the thermal-hydraulic zone-by-zone oil coolers design calculations. The report presents data about the developed software for operational monitoring, assessment of equipment parameters features as well as its implementation on five power plants.

Rapid method for quantification of seven synthetic pigments in colored Chinese steamed buns using UFLC-MS/MS without SPE.

PubMed

Gao, He-Gang; Gong, Wen-Jie; Zhao, Yong-Gang

2015-01-01

Synthetic pigments are still used instead of natural pigments in many foods and their residues in food could be an important risk to human health. A simple and rapid analytical method combining the low-cost extraction protocol with ultra-fast liquid chromatography-tandem quadrupole mass spectrometry (UFLC-MS/MS) was developed for the simultaneous determination of seven synthetic pigments used in colored Chinese steamed buns. For the first time, ethanol/ammonia solution/water (7:2:1, v/v/v) was used as extraction solution for the synthetic pigments in colored Chinese steamed buns. The results showed that the property of the extraction solution used in this method was more effective than critic acid solution, which is used in the polyamide adsorption method. The limits of quantification for the seven synthetic pigments ranged from 0.15 to 0.50 μg/kg. The present method was successfully applied to samples of colored Chinese steamed buns for food-safety risk monitoring in Zhejiang Province, China. The results found sunset yellow pigment in six out of 300 colored Chinese steamed buns (from 0.50 to 32.6 μg/kg).

Results of a Monitoring Program at a Sediment Trap in the Elbe Estuary near Wedel

NASA Astrophysics Data System (ADS)

Ohle, N.; Entelmann, I.; Winterscheid, A.

2012-04-01

In June 2008 a sediment trap was built in the Tidal Elbe River near Wedel. The trap is about 2 km long, 2 m deep in average and spans the whole roughly 300 meter width of the navigation channel. The geometry of the trap is aligned to the zones with maximum sedimentation in the past. Therefore it has a triangular geometry on the western side. The dimensions of the sediment traps were restricted due to more or less legal circumstances. A longer and deeper sediment trap requires a planning approval as the used dimensions were evaluated as supporting maintenance works. Hamburg Port Authority (HPA) and the Waterway and Shipping Administration of the Federal Government (WSV) want jointly further improve the management of sediments and dredging activities by means of this measure. Until end of 2010 a total amount of about 4 Mio. m3 of fine sediments has been removed from the basin in 4 maintenance campaigns and was relocated about 50 km downstream to the relocation area at Elbe-km 690. The main function of the sediment trap is to reduce the residual transport of marine sediments from the North Sea in direction of Hamburg by trapping minor polluted sediments before they reach the port area. In this area these sediments mix-up with higher polluted sediments. The three specific objectives of the sediment trap are: to reduce the dredging amounts in the area of the Hamburg port; to be able to relocate minor polluted sediments further downstream to areas where the ebb-tidal current dominates the flow regime; to economically optimize maintenance dredging activities within the sediment trap. Beside these qualitative advantages the sediment trap has additional advantages in regard to maintenance works of the fairway due to a higher flexibility. Since sediments are collected in one defined place they can be dredged more efficiently through the use of optimized equipment, e.g. larger hopper dredgers can be used resulting in a cost-benefit. Another optimisation possibility can be found in the higher densities that can be dredged through a longer period of consolidation, resulting in higher hopper densities. In contrast to these advantages, a cost increase through preparation of the sediment trap in the first place needs to be considered. In order to report stakeholders, HPA runs a monitoring programme on how this sediment trap affects hydrology, morphology and ecological issues. Besides that, HPA carries out further monitoring activities tailored to system analysis and to study morphological processes in detail. The Federal Institute of Hydrology (BfG) analyses the data and carries out further investigations on the measuring data (refer to BfG, 2009 and BfG, 2010). Hydrological and morphological parameters are being constantly recorded at four monitoring stations which are located up- and downstream to the sediment trap. The current velocities were analysed by ADCP campaigns on several profiles. In order to study the near-bed morphological processes a steel-frame-platform - equipped with measurement devices and traps for suspended material - was installed directly on the bottom of the sediment trap. A pump sampler collects water samples from a survey vessel to obtain suspended matter (SPM) content. Furthermore, HPA uses a multibeam echo sounder to observe the resulting sedimentation patterns in the trap. Surface grab samples are used to collect data about grain size distributions. Echo soundings with two frequencies and sediment echo sounders were used to get a picture of the density and consolidation of the settled sediments within the trap. In this paper short results of the mentioned monitoring program should be presented.

Camera Traps on Wildlife Crossing Structures as a Tool in Gray Wolf (Canis lupus) Management - Five-Years Monitoring of Wolf Abundance Trends in Croatia

PubMed Central

Križan, Josip; Gužvica, Goran

2016-01-01

The conservation of gray wolf (Canis lupus) and its coexistence with humans presents a challenge and requires continuous monitoring and management efforts. One of the non-invasive methods that produces high-quality wolf monitoring datasets is camera trapping. We present a novel monitoring approach where camera traps are positioned on wildlife crossing structures that channel the animals, thereby increasing trapping success and increasing the cost-efficiency of the method. In this way we have followed abundance trends of five wolf packs whose home ranges are intersected by a motorway which spans throughout the wolf distribution range in Croatia. During the five-year monitoring of six green bridges we have recorded 28 250 camera-events, 132 with wolves. Four viaducts were monitored for two years, recording 4914 camera-events, 185 with wolves. We have detected a negative abundance trend of the monitored Croatian wolf packs since 2011, especially severe in the northern part of the study area. Further, we have pinpointed the legal cull as probable major negative influence on the wolf pack abundance trends (linear regression, r2 > 0.75, P < 0.05). Using the same approach we did not find evidence for a negative impact of wolves on the prey populations, both wild ungulates and livestock. We encourage strict protection of wolf in Croatia until there is more data proving population stability. In conclusion, quantitative methods, such as the one presented here, should be used as much as possible when assessing wolf abundance trends. PMID:27327498

Camera Traps on Wildlife Crossing Structures as a Tool in Gray Wolf (Canis lupus) Management - Five-Years Monitoring of Wolf Abundance Trends in Croatia.

PubMed

Šver, Lidija; Bielen, Ana; Križan, Josip; Gužvica, Goran

2016-01-01

The conservation of gray wolf (Canis lupus) and its coexistence with humans presents a challenge and requires continuous monitoring and management efforts. One of the non-invasive methods that produces high-quality wolf monitoring datasets is camera trapping. We present a novel monitoring approach where camera traps are positioned on wildlife crossing structures that channel the animals, thereby increasing trapping success and increasing the cost-efficiency of the method. In this way we have followed abundance trends of five wolf packs whose home ranges are intersected by a motorway which spans throughout the wolf distribution range in Croatia. During the five-year monitoring of six green bridges we have recorded 28 250 camera-events, 132 with wolves. Four viaducts were monitored for two years, recording 4914 camera-events, 185 with wolves. We have detected a negative abundance trend of the monitored Croatian wolf packs since 2011, especially severe in the northern part of the study area. Further, we have pinpointed the legal cull as probable major negative influence on the wolf pack abundance trends (linear regression, r2 > 0.75, P < 0.05). Using the same approach we did not find evidence for a negative impact of wolves on the prey populations, both wild ungulates and livestock. We encourage strict protection of wolf in Croatia until there is more data proving population stability. In conclusion, quantitative methods, such as the one presented here, should be used as much as possible when assessing wolf abundance trends.

Evaluation of sticky traps for adult Aedes mosquitoes in Malaysia: a potential monitoring and surveillance tool for the efficacy of control strategies.

PubMed

Roslan, Muhammad Aidil; Ngui, Romano; Vythilingam, Indra; Sulaiman, Wan Yusoff Wan

2017-12-01

The present study compared the performance of sticky traps in order to identify the most effective and practical trap for capturing Aedes aegypti and Aedes albopictus mosquitoes. Three phases were conducted in the study, with Phase 1 evaluating the five prototypes (Models A, B, C, D, and E) of sticky trap release-and-recapture using two groups of mosquito release numbers (five and 50) that were released in each replicate. Similarly, Phase 2 compared the performance between Model E and the classical ovitrap that had been modified (sticky ovitrap), using five and 50 mosquito release numbers. Further assessment of both traps was carried out in Phase 3, in which both traps were installed in nine sampling grids. Results from Phase 1 showed that Model E was the trap that recaptured higher numbers of mosquitoes when compared to Models A, B, C, and D. Further assessment between Model E and the modified sticky ovitrap (known as Model F) found that Model F outperformed Model E in both Phases 2 and 3. Thus, Model F was selected as the most effective and practical sticky trap, which could serve as an alternative tool for monitoring and controlling dengue vectors in Malaysia. © 2017 The Society for Vector Ecology.

The STEAM Project

NASA Astrophysics Data System (ADS)

von Schéele, F.; Steam Team

The proposed satellite project "Stratosphere-Troposphere Exchange And climate Monitor" (STEAM) is dedicated to the investigation of chemical, dynamical, and radiative processes in the upper troposphere and lower stratosphere (UT/LS) altitude range and their links with the Earth climate and stratosphere evolution. The main objectives are to provide vertically and horizontally resolved information on the global distributions of UT/LS key species such as H2O, O3, and CO, and global fields of O3, H2O and halogen compounds responsible for the O3 destruction like ClO in the stratosphere. The UT/LS region plays an important role in the Earth's climate system. Despite its importance there is still a lack of accurate, height-resolved data from the UT/LS. Confronting 3-D climate and chemical-transport models with STEAM observations will improve our knowledge of this atmospheric region. Furthermore, it will be important to continue monitoring the evolution of the stratosphere regarding the expected decline of halogen compounds and recovery of the ozone layer. STEAM consists of a microwave limb-sounding instrument, operating in the 320-360 GHz range to sound the UT/LS and in the 485-505 GHz range to sound the stratosphere, and an optical instrument. By sounding the Earth atmosphere's limb from 5 to 28 km employing a new technique with 8 simultaneous measurements, STEAM will produce a global dataset of UT/LS key species with high vertical (1.5-2.5 km) and horizontal (30-50 km) resolution. The sub-mm band will cover 15 to 40 km. An optical instrument, co-aligned with the mm-wave band, will support micro-wave measurements with cloud indications and in addition provide stratospheric ozone, and aerosol and cloud property measurements. STEAM, planned for a launch in 2008, will be a collaboration between laboratories, industry and agencies in several countries. The Odin heritage of the project (e.g. microwave and optical instruments) provides technical maturity and will help to keep instrument development efforts down. It will also help in the ground-segment development of a 2-D forward and retrieval model and of data assimilation tools. The STEAM mission definition review was held on February 19, concluding the first part of a phase A study. An update of the mission and instrument definitions and the project status will be given at COSPAR.

40 CFR 63.3557 - What are the requirements for continuous parameter monitoring system installation, operation, and...

Code of Federal Regulations, 2013 CFR

2013-07-01

... monitor the total regeneration desorbing gas (e.g., steam or nitrogen) mass flow for each regeneration cycle, the carbon bed temperature after each regeneration and cooling cycle, and comply with paragraphs (a)(3) through (5) and (d)(1) and (2) of this section. (1) The regeneration desorbing gas mass flow...

40 CFR 63.3168 - What are the requirements for continuous parameter monitoring system installation, operation, and...

Code of Federal Regulations, 2012 CFR

2012-07-01

... regenerative carbon adsorber as an add-on control device, you must monitor the total regeneration desorbing gas (e.g., steam or nitrogen) mass flow for each regeneration cycle, the carbon bed temperature after each regeneration and cooling cycle, and comply with paragraphs (a)(3) through (5) and (d)(1) and (2...

40 CFR 63.3557 - What are the requirements for continuous parameter monitoring system installation, operation, and...

Code of Federal Regulations, 2014 CFR

2014-07-01

... monitor the total regeneration desorbing gas (e.g., steam or nitrogen) mass flow for each regeneration cycle, the carbon bed temperature after each regeneration and cooling cycle, and comply with paragraphs (a)(3) through (5) and (d)(1) and (2) of this section. (1) The regeneration desorbing gas mass flow...

40 CFR 63.3557 - What are the requirements for continuous parameter monitoring system installation, operation, and...

Code of Federal Regulations, 2012 CFR

2012-07-01

... monitor the total regeneration desorbing gas (e.g., steam or nitrogen) mass flow for each regeneration cycle, the carbon bed temperature after each regeneration and cooling cycle, and comply with paragraphs (a)(3) through (5) and (d)(1) and (2) of this section. (1) The regeneration desorbing gas mass flow...

40 CFR 60.4176 - Additional requirements to provide heat input data.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Additional requirements to provide heat... Compliance Times for Coal-Fired Electric Steam Generating Units Monitoring and Reporting § 60.4176 Additional requirements to provide heat input data. The owner or operator of a Hg Budget unit that monitors and reports Hg...

Influence of trap design on capture of female grape berry moth (lepidoptera: tortricidae) with a kairomone Lure

USDA-ARS?s Scientific Manuscript database

Oil-coated clear panel traps baited with a host plant-based kairomone lure are effective in monitoring female grape berry moth (GBM), Paralobesia viteana (Clemens) (Lepidoptera:Tortricidae), but servicing these traps in a vineyard is cumbersome. In this study, we compared the performance of six diff...

Ammonium carbonate loss rates from lures differentially affect trap captures of Rhagoletis indifferens (Diptera: Tephritidae) and non-target flies

USDA-ARS?s Scientific Manuscript database

Western cherry fruit fly, Rhagoletis indifferens Curran (Diptera: Tephritidae), is a pest of cherry (Prunus spp.) in western North America that can be monitored using traps baited with ammonia. However, ammonia-based attractants also attract non-target Diptera that clutter traps. Here, the hypothe...

Molecular markers for identification of Hessian fly males caught on pheromone traps

USDA-ARS?s Scientific Manuscript database

Pheromone traps have been widely used to monitor insect populations in nature. However, pheromone traps for the Hessian fly (Mayetiola destructor), one of the most destructive insect pests of wheat, have been used only in recent years. Because Hessian fly male adults are small and fragile, it is d...

Monitoring of Dermanyssus gallinae in free-range poultry farms.

PubMed

Zenner, L; Bon, G; Chauve, C; Nemoz, C; Lubac, S

2009-06-01

Various methods for monitoring Dermanyssus gallinae infestations within free-range egg production units were compared. The study was carried out in five egg-producing free-range poultry buildings infested with D. gallinae. Each farm was divided into six zones (each zone including nest boxes, perches and duckboard) for placing two types of traps (corrugated cardboard and thick card traps) or examining dried droppings for presence of mites. Traps were removed 24 h later, placed into bags and mites were counted at the laboratory using binocular magnification. Droppings were also inspected by eye and mite numbers were estimated. All the methods used allowed us to detect mites although their efficacy differed. The number of mites collected was independent of the type of trap used. Examination of the droppings did not differentiate between buildings with differing mite populations. Placing traps in the nest boxes is a less reliable indicator than placing them on the perches. It appears that the most coherent method for evaluating the D. gallinae population within a free-range flock is to place thick card traps throughout the building, on perches favoured by birds.

A resettable in-line particle concentrator using AC electrokinetics for distributed monitoring of microalgae in source waters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yuan, Quan; Purdue Univ., West Lafayette, IN; Wu, Jayne

Green algae have been studied as an important and effective biomarker to indicate water quality due to their sensitivity to toxic agents in freshwater sources. But, conventional methods to monitor algal physiology use a chlorophyll fluorometer whose use is hampered by high-cost, large footprint, and limited sensitivity for practical samples containing low algal concentration. In order to overcome these constraints, we developed a multi-level electrode platform for resettable trapping of algae via AC electro-osmosis (ACEO) and negative dielectrophoresis. Preliminary experiments were performed in freshwater with conductivity of 0.02 S/m. Algal trapping was demonstrated at a low voltage of 2 V.more » The concentration effect was experimentally verified by measuring the fluorescence intensity of algae and using hemocytometer counting chambers at the inlet and outlet of the multilevel microchannel lab-on-a-chip. An optimal frequency was found for trapping, which agrees with the frequency dependence of ACEO flow velocity. Through-flow rate and electrode dimensions were optimized as well. Trapping efficiencies within the range of 26% - 65% have been obtained. A maximum trapping rate of 182 cells/s was obtained with a flow rate of 20 l/min. Our lab-on-a-chip shows high potential for improving the limit of detection in algal monitoring and enabling the development of a portable, integrated and automated system for monitoring the quality of source drinking waters.« less

A resettable in-line particle concentrator using AC electrokinetics for distributed monitoring of microalgae in source waters

DOE PAGES

Yuan, Quan; Purdue Univ., West Lafayette, IN; Wu, Jayne; ...

2016-12-29

Green algae have been studied as an important and effective biomarker to indicate water quality due to their sensitivity to toxic agents in freshwater sources. But, conventional methods to monitor algal physiology use a chlorophyll fluorometer whose use is hampered by high-cost, large footprint, and limited sensitivity for practical samples containing low algal concentration. In order to overcome these constraints, we developed a multi-level electrode platform for resettable trapping of algae via AC electro-osmosis (ACEO) and negative dielectrophoresis. Preliminary experiments were performed in freshwater with conductivity of 0.02 S/m. Algal trapping was demonstrated at a low voltage of 2 V.more » The concentration effect was experimentally verified by measuring the fluorescence intensity of algae and using hemocytometer counting chambers at the inlet and outlet of the multilevel microchannel lab-on-a-chip. An optimal frequency was found for trapping, which agrees with the frequency dependence of ACEO flow velocity. Through-flow rate and electrode dimensions were optimized as well. Trapping efficiencies within the range of 26% - 65% have been obtained. A maximum trapping rate of 182 cells/s was obtained with a flow rate of 20 l/min. Our lab-on-a-chip shows high potential for improving the limit of detection in algal monitoring and enabling the development of a portable, integrated and automated system for monitoring the quality of source drinking waters.« less

Straight-line drift fences and pitfall traps

USGS Publications Warehouse

Corn, Paul Stephen

1994-01-01

Straight-line drift fences typically are short barriers (5-15 m) that direct animals traveling on the substrate surface into traps places at the ends of or beside the barriers. Traps (described below) can be pitfalls, funnel traps, or a combination of the two. Drift fences with pitfall or funnel traps and pitfall traps without fences are used commonly to inventory and monitor populations of amphibians and reptiles. For example, 9 of 17 field studies reported for management of terrestrial vertebrates (Sarzo et al. 1988) used these techniques to sample amphibians. Drift fences with pitfall traps can be used to determine species richness at a site and to detect the presence of rare species. They also can yield data on relative abundances and habitat use of selected species. Pitfall traps arrayed in a grid without fences can also be used to study the population ecology and habitat use of selected species. Population density can be estimated with this latter technique if used in conjunction with mark-recapture techniques (see Chapter 8). Drift fence arrays or pitfall grids can be left in place for long-term monitoring. In this section, I discuss the use of this technique to obtain data on amphibians away from breeding ponds. Use of drift fences and traps to monitory amphibian activity at breeding ponds is discussed in the section "Drift Fences Encircling Breeding Sits", below (technique 9). Some materials and procedures are common to both techniques. Investigators contemplating the use of drift fences and traps in any context should read both accounts.

Prospects for the development of coal-steam plants in Russia

NASA Astrophysics Data System (ADS)

Tumanovskii, A. G.

2017-06-01

Evaluation of the technical state of the modern coal-fired power plants and quality of coal consumed by Russian thermal power plants (TPP) is provided. Measures aimed at improving the economic and environmental performance of operating 150-800 MW coal power units are considered. Ways of efficient use of technical methods of NO x control and electrostatic precipitators' upgrade for improving the efficiency of ash trapping are summarized. Examples of turbine and boiler equipment efficiency upgrading through its deep modernization are presented. The necessity of the development and introduction of new technologies in the coal-fired power industry is shown. Basic technical requirements for a 660-800 MW power unit with the steam conditions of 28 MPa, 600/600°C are listed. Design solutions taking into account features of Russian coal combustion are considered. A field of application of circulating fluidized bed (CFB) boilers and their effectiveness are indicated. The results of development of a new generation coal-fired TPP, including a steam turbine with an increased efficiency of the compartments and disengaging clutch, an elevated steam conditions boiler, and a highly efficient NO x /SO2 and ash particles emission control system are provided. In this case, the resulting ash and slag are not to be sent to the ash dumps and are to be used to a maximum advantage. Technical solutions to improve the efficiency of coal gasification combined cycle plants (CCP) are considered. A trial plant based on a 16 MW gas turbine plant (GTP) and an air-blown gasifier is designed as a prototype of a high-power CCP. The necessity of a state-supported technical reequipment and development program of operating coal-fired power units, as well as putting into production of new generation coal-fired power plants, is noted.

Evaluation of capture techniques on lesser prairie-chicken trap injury and survival

USGS Publications Warehouse

Grisham, Blake A.; Boal, Clint W.; Mitchell, Natasia R.; Gicklhorn, Trevor S.; Borsdorf, Philip K.; Haukos, David A.; Dixon, Charles

2015-01-01

Ethical treatment of research animals is required under the Animal Welfare Act. This includes trapping methodologies that reduce unnecessary pain and duress. Traps used in research should optimize animal welfare conditions within the context of the proposed research study. Several trapping techniques are used in the study of lesser prairie-chickens, despite lack of knowledge of trap injury caused by the various methods. From 2006 to 2012, we captured 217, 40, and 144 lesser prairie-chickens Tympanuchus pallidicinctus using walk-in funnel traps, rocket nets, and drop nets, respectively, in New Mexico and Texas, to assess the effects of capture technique on injury and survival of the species. We monitored radiotagged, injured lesser prairie-chickens 7–65 d postcapture to assess survival rates of injured individuals. Injuries occurred disproportionately among trap type, injury type, and sex. The predominant injuries were superficial cuts to the extremities of males captured in walk-in funnel traps. However, we observed no mortalities due to trapping, postcapture survival rates of injured birds did not vary across trap types, and the daily survival probability of an injured and uninjured bird was ≥99%. Frequency and intensity of injuries in walk-in funnel traps are due to the passive nature of these traps (researcher cannot select specific individuals for capture) and incidental capture of individuals not needed for research. Comparatively, rocket nets and drop nets allow observers to target birds for capture and require immediate removal of captured individuals from the trap. Based on our results, trap injuries would be reduced if researchers monitor and immediately remove birds from walk-in funnels before they injure themselves; move traps to target specific birds and reduce recaptures; limit the number of consecutive trapping days on a lek; and use proper netting techniques that incorporate quick, efficient, trained handling procedures.

Steam injection pilot study in a contaminated fractured limestone (Maine, USA): Modeling and analysis of borehole radar reflection data

USGS Publications Warehouse

Gregoire, C.; Lane, J.W.; Joesten, P.K.

2005-01-01

Steam-enhanced remediation (SER) has been successfully used to remove DNAPL and LNAPL contaminants in porous media. Between August and November 2002, SER was tested in fractured limestone at the former Loring Air Force Base, in Maine, USA. During the SER investigation, the U.S. Geological Survey conducted a series of borehole radar surveys to evaluate the effectiveness of radar methods for monitoring the movement of steam and heat through the fractured limestone. The data were collected before steam injection, 10 days after the beginning of injection, and at the end of injection. In this paper, reflection-mode borehole radar data from wells JBW-7816 and JBW-7817A are presented and discussed. Theoretical modeling was performed to predict the variation of fracture reflectivity owed to heating, to show displacement of water and to assess the effect of SER at the site. Analysis of the radar profile data indicates some variations resulting from heating (increase of continuity of reflectors, attenuation of deeper reflections) but no substantial variation of traveltimes. Spectral content analysis of several individual reflections surrounding the boreholes was used to investigate the replacement of water by steam in the fractures. Observed decrease in radar reflectivity was too small to be explained by a replacement of water by steam, except for two high-amplitude reflectors, which disappeared near the end of the injection; moreover, no change of polarity, consistent with steam replacing water, was observed. The decrease of amplitude was greater for reflectors near well JBW-7817A and is explained by a greater heating around this well.

Wireless Monitoring of the Height of Condensed Water in Steam Pipes

NASA Technical Reports Server (NTRS)

Lee, Hyeong Jae; Bar-Cohen, Yoseph; Lih, Shyh-Shiuh; Badescu, Mircea; Dingizian, Arsham; Takano, Nobuyuki; Blosiu, Julian O.

2014-01-01

A wireless health monitoring system has been developed for determining the height of water condensation in the steam pipes and the data acquisition is done remotely using a wireless network system. The developed system is designed to operate in the harsh environment encountered at manholes and the pipe high temperature of over 200 °C. The test method is an ultrasonic pulse-echo and the hardware includes a pulser, receiver and wireless modem for communication. Data acquisition and signal processing software were developed to determine the water height using adaptive signal processing and data communication that can be controlled while the hardware is installed in a manhole. A statistical decision-making tool is being developed based on the field test data to determine the height of in the condensed water under high noise conditions and other environmental factors.

Mobility Effect on Poroelastic Seismic Signatures in Partially Saturated Rocks With Applications in Time-Lapse Monitoring of a Heavy Oil Reservoir

NASA Astrophysics Data System (ADS)

Zhao, Luanxiao; Yuan, Hemin; Yang, Jingkang; Han, De-hua; Geng, Jianhua; Zhou, Rui; Li, Hui; Yao, Qiuliang

2017-11-01

Conventional seismic analysis in partially saturated rocks normally lays emphasis on estimating pore fluid content and saturation, typically ignoring the effect of mobility, which decides the ability of fluids moving in the porous rocks. Deformation resulting from a seismic wave in heterogeneous partially saturated media can cause pore fluid pressure relaxation at mesoscopic scale, thereby making the fluid mobility inherently associated with poroelastic reflectivity. For two typical gas-brine reservoir models, with the given rock and fluid properties, the numerical analysis suggests that variations of patchy fluid saturation, fluid compressibility contrast, and acoustic stiffness of rock frame collectively affect the seismic reflection dependence on mobility. In particular, the realistic compressibility contrast of fluid patches in shallow and deep reservoir environments plays an important role in determining the reflection sensitivity to mobility. We also use a time-lapse seismic data set from a Steam-Assisted Gravity Drainage producing heavy oil reservoir to demonstrate that mobility change coupled with patchy saturation possibly leads to seismic spectral energy shifting from the baseline to monitor line. Our workflow starts from performing seismic spectral analysis on the targeted reflectivity interface. Then, on the basis of mesoscopic fluid pressure diffusion between patches of steam and heavy oil, poroelastic reflectivity modeling is conducted to understand the shift of the central frequency toward low frequencies after the steam injection. The presented results open the possibility of monitoring mobility change of a partially saturated geological formation from dissipation-related seismic attributes.

Mass sensors with mechanical traps for weighing single cells in different fluids.

PubMed

Weng, Yaochung; Delgado, Francisco Feijó; Son, Sungmin; Burg, Thomas P; Wasserman, Steven C; Manalis, Scott R

2011-12-21

We present two methods by which single cells can be mechanically trapped and continuously monitored within the suspended microchannel resonator (SMR) mass sensor. Since the fluid surrounding the trapped cell can be quickly and completely replaced on demand, our methods are well suited for measuring changes in cell size and growth in response to drugs or other chemical stimuli. We validate our methods by measuring the density of single polystyrene beads and Saccharomyces cerevisiae yeast cells with a precision of approximately 10(-3) g cm(-3), and by monitoring the growth of single mouse lymphoblast cells before and after drug treatment.

Micro Penning Trap for Continuous Magnetic Field Monitoring in High Radiation Environments

NASA Astrophysics Data System (ADS)

Latorre, Javiera; Bollen, Georg; Gulyuz, Kerim; Ringle, Ryan; Bado, Philippe; Dugan, Mark; Lebit Team; Translume Collaboration

2016-09-01

As new facilities for rare isotope beams, like FRIB at MSU, are constructed, there is a need for new instrumentation to monitor magnetic fields in beam magnets that can withstand the higher radiation level. Currently NMR probes, the instruments used extensively to monitor magnetic fields, do not have a long lifespans in radiation-high environments. Therefore, a radiation-hard replacement is needed. We propose to use Penning trap mass spectrometry techniques to make high precision magnetic field measurements. Our Penning microtrap will be radiation resistant as all of the vital electronics will be at a safe distance from the radiation. The trap itself is made from materials not subject to radiation damage. Penning trap mass spectrometers can determine the magnetic field by measuring the cyclotron frequency of an ion with a known mass and charge. This principle is used on the Low Energy Beam Ion Trap (LEBIT) minitrap at NSCL which is the foundation for the microtrap. We have partnered with Translume, who specialize in glass micro-fabrication, to develop a microtrap in fused-silica glass. A microtrap is finished and ready for testing at NSCL with all of the electronic and hardware components setup. DOE Phase II SBIR Award No. DE-SC0011313, NSF Award Number 1062410 REU in Physics, NSF under Grant No. PHY-1102511.

Evaluation of a sticky trap (AedesTraP), made from disposable plastic bottles, as a monitoring tool for Aedes aegypti populations.

PubMed

de Santos, Eloína Maria Mendonça; de Melo-Santos, Maria Alice Varjal; de Oliveira, Claudia Maria Fontes; Correia, Juliana Cavalcanti; de Albuquerque, Cleide Maria Ribeiro

2012-09-07

Dengue virus, which is transmitted by Aedes aegypti mosquitoes is the most important emerging viral disease, infecting more than 50 million people annually. Currently used sticky traps are useful tools for monitoring and control of A. aegypti, despite differences in efficiency, labor requirements and cost. In the present work, a field assay was carried out to evaluate the performance of a sticky trap (AedesTrap), produced using disposable material, in capturing gravid Aedes spp. females. Additionally, conditions necessary for the improved performance of the device, such as number of traps per site and location (indoors or outdoors) were evaluated. During a one year period, traps were placed in a dengue endemic area in 28 day cycles. The trap, named AedesTrap, consisted of a disposable plastic soda bottle coated inside with colophony resin, which served as a sticky substrate. Disposable bottles were donated by restaurants, and traps were made by laboratory staff, reducing the cost of the sticky trap (less than U$3). Mosquito capture in indoor and outdoor areas was compared by placing the traps in laundry room, kitchen or bedroom (indoors) and front or back yard (outdoors). The relationship between the number of AedesTraps and quantity of captured mosquitoes was investigated by utilizing one or three traps/site. During a 28 day cycle, a single AedesTrap was capable of capturing up to 15 A. aegypti in a house, with a mean capture of 0.5 to 2.63 females per premise. The AedesTrap collected three times more outdoors versus indoors. Similarly, the capability of detecting Aedes spp. infestation, and of capturing females, was three times higher when using three AedesTraps per house, compared with one trap per house. AedesTrap was shown to be capable of capturing A. aegypti and other culicidae, providing information on the adult mosquito population, and allowing the identification of areas critically infested by mosquitoes. Low requirements for skilled labor together with easy maintenance and low cost are additional advantages of using this sticky trap.

Evaluation of a sticky trap (AedesTraP), made from disposable plastic bottles, as a monitoring tool for Aedes aegypti populations

PubMed Central

2012-01-01

Background Dengue virus, which is transmitted by Aedes aegypti mosquitoes is the most important emerging viral disease, infecting more than 50 million people annually. Currently used sticky traps are useful tools for monitoring and control of A. aegypti, despite differences in efficiency, labor requirements and cost. In the present work, a field assay was carried out to evaluate the performance of a sticky trap (AedesTrap), produced using disposable material, in capturing gravid Aedes spp. females. Additionally, conditions necessary for the improved performance of the device, such as number of traps per site and location (indoors or outdoors) were evaluated. Methods During a one year period, traps were placed in a dengue endemic area in 28 day cycles. The trap, named AedesTrap, consisted of a disposable plastic soda bottle coated inside with colophony resin, which served as a sticky substrate. Disposable bottles were donated by restaurants, and traps were made by laboratory staff, reducing the cost of the sticky trap (less than U$3). Mosquito capture in indoor and outdoor areas was compared by placing the traps in laundry room, kitchen or bedroom (indoors) and front or back yard (outdoors). The relationship between the number of AedesTraps and quantity of captured mosquitoes was investigated by utilizing one or three traps/site. Results During a 28 day cycle, a single AedesTrap was capable of capturing up to 15 A. aegypti in a house, with a mean capture of 0.5 to 2.63 females per premise. The AedesTrap collected three times more outdoors versus indoors. Similarly, the capability of detecting Aedes spp. infestation, and of capturing females, was three times higher when using three AedesTraps per house, compared with one trap per house. Conclusions AedesTrap was shown to be capable of capturing A. aegypti and other culicidae, providing information on the adult mosquito population, and allowing the identification of areas critically infested by mosquitoes. Low requirements for skilled labor together with easy maintenance and low cost are additional advantages of using this sticky trap. PMID:22958376

Improved capture of Drosophila suzukii by a trap baited with two attractants in the same device

PubMed Central

Tadeo, Eduardo; Toledo-Hérnandez, Ricardo A.; Carmona, Lino; Lima, Itzel; Williams, Trevor

2017-01-01

The improvement of trap-lure combinations is an important part of integrated pest management programs that involve monitoring pests for timely insecticide applications, or for their use in control strategies such as mass trapping or bait stations. In this study improvements in the capture of Drosophila suzukii were not observed following the inclusion of different color stimuli with respect to a red-black stripe cup trap. This red-black stripe trap with a hemispherical dome-shaped lid had a significantly improved physical retention of flies compared to traps fitted with a flat lid. Retention was further improved when an additional tube device, which could be baited with a supplemental attractant, was introduced through the dome-shaped lid. Under laboratory conditions, this trap, in which apple cider vinegar + 10% ethanol was present as the drowning solution and the additional tube device was baited with a fermenting mixture of sugar and yeast, was significantly more effective in catching D. suzukii flies than other conventional attractants or a commercial lure. The capture rate of this trap-lure combination remained higher than that of a commercial lure, even after 20 days of use under laboratory conditions. In a guava orchard this trap was 15-fold more effective in catching D. suzukii flies than similar traps baited with apple cider vinegar alone, 4 to 7 fold more effective than similar traps baited with a commercial lure, and 1.7-fold more effective than a fermenting mixture of yeasts and wheat flour. In commercial blackberry orchards, this trap was 6-fold more effective in trapping D. suzukii flies than the clear trap baited with apple cider vinegar used by growers. The efficacy of this trap presents a promising line of future research for monitoring and control of D. suzukii and likely other drosophilid pests. PMID:29149190

Improved capture of Drosophila suzukii by a trap baited with two attractants in the same device.

PubMed

Lasa, Rodrigo; Tadeo, Eduardo; Toledo-Hérnandez, Ricardo A; Carmona, Lino; Lima, Itzel; Williams, Trevor

2017-01-01

The improvement of trap-lure combinations is an important part of integrated pest management programs that involve monitoring pests for timely insecticide applications, or for their use in control strategies such as mass trapping or bait stations. In this study improvements in the capture of Drosophila suzukii were not observed following the inclusion of different color stimuli with respect to a red-black stripe cup trap. This red-black stripe trap with a hemispherical dome-shaped lid had a significantly improved physical retention of flies compared to traps fitted with a flat lid. Retention was further improved when an additional tube device, which could be baited with a supplemental attractant, was introduced through the dome-shaped lid. Under laboratory conditions, this trap, in which apple cider vinegar + 10% ethanol was present as the drowning solution and the additional tube device was baited with a fermenting mixture of sugar and yeast, was significantly more effective in catching D. suzukii flies than other conventional attractants or a commercial lure. The capture rate of this trap-lure combination remained higher than that of a commercial lure, even after 20 days of use under laboratory conditions. In a guava orchard this trap was 15-fold more effective in catching D. suzukii flies than similar traps baited with apple cider vinegar alone, 4 to 7 fold more effective than similar traps baited with a commercial lure, and 1.7-fold more effective than a fermenting mixture of yeasts and wheat flour. In commercial blackberry orchards, this trap was 6-fold more effective in trapping D. suzukii flies than the clear trap baited with apple cider vinegar used by growers. The efficacy of this trap presents a promising line of future research for monitoring and control of D. suzukii and likely other drosophilid pests.

Prototype Technology for Monitoring Volatile Organics. Volume 1.

DTIC Science & Technology

1988-03-01

117, pp. 285-294. Grote, J.O. and Westendorf , R.G., "An Automatic Purge and Trap Concentrator," American Laboratory, December 1979. Khromchenko, Y.L...Environmental Monitoring and Support Laboratory, Office of Research and Development, Cincinnati, OH. Westendorf , R.G., "Closed-loop Stripping Analysis...Technique and Applications," American Laboratory, December 1982. Westendorf , R.G., "Development Application of A Semi-Automatic Purge and Trap Concentrator

Sulfur removal and comminution of carbonaceous material

DOEpatents

Narain, N.K.; Ruether, J.A.; Smith, D.N.

1987-10-07

Finely divided, clean coal or other carbonaceous material is provided by forming a slurry of coarse coal in aqueous alkali solution and heating the slurry under pressure to above the critical conditions of steam. The supercritical fluid penetrates and is trapped in the porosity of the coal as it swells in a thermoplastic condition at elevated temperature. By a sudden, explosive release of pressure the coal is fractured into finely divided particles with release of sulfur-containing gases and minerals. The finely divided coal is recovered from the minerals for use as a clean coal product. 2 figs.

Beetle fauna captured in traps baited with Tomicus piniperda pheromone blends in a pine stand in Central Croatia

Treesearch

Milan Pernek; Boris Hrasovec; Miljenko Zupanic

2003-01-01

During field evaluations of pheromone blends used for monitoring Tomicus piniperda beetles, many non-target beetles were captured and identified. Five pheromone blends, plus commercially available TOMODOR were used in two different traps: the IPM Tech Intercept PTBB and the THEYSOHN intercept barrier trap. In addition to Tomicus...

Insects in IBL-4 pine weevil traps

Treesearch

I. Skrzecz

2003-01-01

Pipe traps (IBL-4) are used in Polish coniferous plantations to monitor and control the pine weevil (Hylobius abietis L.). This study was conducted in a one-year old pine plantation established on a reforested clear-cut area in order to evaluate the impact of these traps on non-target insects. Evaluation of the catches indicated that species of

Influence of trap design on upwind flight behavior and capture of female grape berry moth (Lepidoptera: Tortricidea) with a kairomone lure

USDA-ARS?s Scientific Manuscript database

Oil-coated clear panel traps baited with a host plant-based kairomone lure are effective in monitoring female grape berry moth (GBM), Paralobesia viteana (Clemens) (Lepidoptera:Tortricidae), but servicing these traps in a vineyard is cumbersome. In this study, we compared the performance of differen...

Impact of trap design and density on effectiveness of a commercial pheromone lure for monitoring navel orangeworm (Lepidoptera: Pyralidae)

USDA-ARS?s Scientific Manuscript database

The navel orangeworm is an important pest of almonds, pistachios, and walnuts. A commercial pheromone lure for this pest became publicly available in 2013. We compared effectiveness of this synthetic lure (NOW Biolure) between common commercial trap designs, and with unmated females in wing traps. O...

New associations of phoretic mites on Pityokteines curvidens (Coleoptera, Curculionidae, Scolytinae)

Treesearch

Milan Pernek; Stefan Wirth; Stacy R. Blomquist; Dimitrios N. Avtzis; John C. Moser

2012-01-01

Abstract: The species composition and abundance of phoretic mites of the bark beetle Pityokteines curvidens caught in pheromone traps were investigated in Croatia. The P. curvidens trapping programs have been in an experimental phase in Croatia since 2004 as a possible monitoring and control system. The trapping program also permits the opportunity to sample phoretic...

Evaluation of two least toxic integrated pest management programs for managing bed bugs (Heteroptera: Cimicidae) with discussion of a bed bug intercepting device.

PubMed

Wang, Changlu; Gibb, Timothy; Bennett, Gary W

2009-05-01

The cost and effectiveness of two bed bug (Cimex lectularius L.) integrated pest management (IPM) programs were evaluated for 10 wk. Sixteen bed bug-infested apartments were chosen from a high-rise low-income apartment building. The apartments were randomly divided into two treatment groups: diatomaceous earth dust-based IPM (D-IPM) and chlorfenapyr spray-based IPM (S-IPM). The initial median (minimum, maximum) bed bug counts (by visual inspection) of the two treatment groups were 73.5 (10, 352) and 77 (18, 3025), respectively. A seminar and an educational brochure were delivered to residents and staff. It was followed by installing encasements on mattresses and box springs and applying hot steam to bed bug-infested areas in all 16 apartments. Diatomaceous earth dust (Mother Earth-D) was applied in the D-IPM group 2 d after steaming. In addition, bed bug-intercepting devices were installed under legs of infested beds or sofas or chairs to intercept bed bugs. The S-IPM group only received 0.5% chlorfenapyr spray (Phantom) after the nonchemical treatments. All apartments were monitored bi-weekly and retreated when necessary. After 10 wk, bed bugs were eradicated from 50% of the apartments in each group. Bed bug count reduction (mean +/- SEM) was 97.6 +/- 1.6 and 89.7 +/- 7.3% in the D-IPM and S-IPM groups, respectively. Mean treatment costs in the 10-wk period were $463 and $482 per apartment in the D-IPM and S-IPM groups, respectively. Bed bug interceptors trapped an average of 219 +/- 135 bed bugs per apartment in 10 wk. The interceptors contributed to the IPM program efficacy and were much more effective than visual inspections in estimating bed bug numbers and determining the existence of bed bug infestations.

40 CFR 63.4768 - What are the requirements for continuous parameter monitoring system installation, operation, and...

Code of Federal Regulations, 2014 CFR

2014-07-01

... using a carbon adsorber as an add-on control device, you must monitor the total regeneration desorbing gas (e.g., steam or nitrogen) mass flow for each regeneration cycle, the carbon bed temperature after each regeneration and cooling cycle, and comply with paragraphs (a)(3) through (5) and (d)(1) and (2...

Development of a system for monitoring technical state of the equipment of a cogeneration steam turbine unit

NASA Astrophysics Data System (ADS)

Aronson, K. E.; Brodov, Yu. M.; Novoselov, V. B.

2012-12-01

Generalized results from the work on developing elements of a comprehensive system for monitoring technical state of the equipment of cogeneration turbines are presented. The parameters of the electrohydraulic turbine control system are considered together with a number of problems concerned with assessing the state of condensers and delivery water heaters.

Multivariate statistical monitoring as applied to clean-in-place (CIP) and steam-in-place (SIP) operations in biopharmaceutical manufacturing.

PubMed

Roy, Kevin; Undey, Cenk; Mistretta, Thomas; Naugle, Gregory; Sodhi, Manbir

2014-01-01

Multivariate statistical process monitoring (MSPM) is becoming increasingly utilized to further enhance process monitoring in the biopharmaceutical industry. MSPM can play a critical role when there are many measurements and these measurements are highly correlated, as is typical for many biopharmaceutical operations. Specifically, for processes such as cleaning-in-place (CIP) and steaming-in-place (SIP, also known as sterilization-in-place), control systems typically oversee the execution of the cycles, and verification of the outcome is based on offline assays. These offline assays add to delays and corrective actions may require additional setup times. Moreover, this conventional approach does not take interactive effects of process variables into account and cycle optimization opportunities as well as salient trends in the process may be missed. Therefore, more proactive and holistic online continued verification approaches are desirable. This article demonstrates the application of real-time MSPM to processes such as CIP and SIP with industrial examples. The proposed approach has significant potential for facilitating enhanced continuous verification, improved process understanding, abnormal situation detection, and predictive monitoring, as applied to CIP and SIP operations. © 2014 American Institute of Chemical Engineers.

Cotton production in the presence of Helicoverpa armigera (Hb.) in Central Greece.

PubMed

Stavridis, D G; Gliatis, A; Deligeorgidis, P N; Giatropoulos, C; Giatropoulos, A; Deligeorgidis, N P; Ipsilandis, C G

2008-11-01

The present study was conducted in 10 different communities of prefecture of Larissa, one of the main cotton-productive areas of Greece. Monitoring of Helicoverpa armigera lasted four years from 2002 to 2005. The monitoring system included four locations within each community and three traps in each location. Traps were of the funnel type, a reusable injection-moulded kind of plastic trap. Pheromone was z-11-hexadecenyl aldehyde 0.36% w/w. Insecticide (Vapona) was used for all the four years, but for years 2003 and 2004 double traps were used additionally, without the presence of insecticide (only with pheromone). Traps containing a pheromone and an insecticide had significantly greater number of insects trapped than those containing no insecticide. Fluctuation of insect population was different from year to year. Correlations on data between years (insect populations and cotton production across all communities) revealed that, when cotton production was low, the number of adult male insects of H. armigera captured in pheromone traps was high (r = -0.69). There were no statistically significant correlations between cotton production and number of trapped insects when data from all communities (across the four years) were used. Local conditions within each area have been proved important and these results were completely different compared to data concerning specific years. Prediction models must be used for average estimations within great areas that include data from many locations.

A collapsible trap for capturing ruffe

USGS Publications Warehouse

Edwards, Andrew J.; Czypinski, Gary D.; Selgeby, James H.

1998-01-01

A modified version of the Windermere trap was designed, constructed, and tested for its effectiveness in capturing ruffe Gymnocephalus cernuus. The inexpensive, lightweight, collapsible trap was easily deployed and retrieved from a small boat. Field tests conducted at the St. Louis River estuary in western Lake Superior in spring 1995 and 1996 indicated that the trap was effective in capturing ruffe. Proportions of the ruffe in trap and bottom trawl catches were similar in 1995 and 1996. This trap could be a useful tool in surveillance, monitoring, or control programs for ruffe or similar species, either to augment existing sampling programs or especially in situations where gillnetting or bottom trawling are not feasible.

Design and evaluation of a simple signaling device for live traps

USGS Publications Warehouse

Benevides, F.L.; Hansen, H.; Hess, S.C.

2008-01-01

Frequent checks of live traps require enormous amounts of labor and add human scents associated with repeated monitoring, which may reduce capture efficiency. To reduce efforts and increase efficiency, we developed a trap-signaling device with long-distance reception, durability in adverse weather, and ease of transport, deployment, and use. Modifications from previous designs include a normally open magnetic switch and a mounting configuration to maximize reception. The system weighed <225 g, was effective ???17.1 km, and failed in <1% of trap-nights. Employing this system, researchers and wildlife managers may reduce the amount of effort checking traps while improving the welfare of trapped animals.

Microfluidic acoustophoretic force based low-concentration oil separation and detection from the environment.

PubMed

Wang, Han; Liu, Zhongzheng; Kim, Sungman; Koo, Chiwan; Cho, Younghak; Jang, Dong-Young; Kim, Yong-Joe; Han, Arum

2014-03-07

Detecting and quantifying extremely low concentrations of oil from the environment have broad applications in oil spill monitoring in ocean and coastal areas as well as in oil leakage monitoring on land. Currently available methods for low-concentration oil detection are bulky or costly with limited sensitivities. Thus they are difficult to be used as portable and field-deployable detectors in the case of oil spills or for monitoring the long-term effects of dispersed oil on marine and coastal ecosystems. Here, we present a low-concentration oil droplet trapping and detection microfluidic system based on the acoustophoresis phenomenon where oil droplets in water having a negative acoustic contrast factor move towards acoustic pressure anti-nodes. By trapping oil droplets from water samples flowing through a microfluidic channel, even very low concentrations of oil droplets can be concentrated to a detectable level for further analyses, which is a significant improvement over currently available oil detection systems. Oil droplets in water were successfully trapped and accumulated in a circular acoustophoretic trapping chamber of the microfluidic device and detected using a custom-built compact fluorescent detector based on the natural fluorescence of the trapped crude oil droplets. After the on-line detection, crude oil droplets released from the trapping chamber were successfully separated into a collection outlet by acoustophoretic force for further off-chip analyses. The developed microfluidic system provides a new way of trapping, detecting, and separating low-concentration crude oil from environmental water samples and holds promise as a low-cost field-deployable oil detector with extremely high sensitivity. The microfluidic system and operation principle are expected to be utilized in a wide range of applications where separating, concentrating, and detecting small particles having a negative acoustic contrast factor are required.

Acoustic emission analysis on tensile failure of steam-side oxide scales formed on T22 alloy superheater tubes

NASA Astrophysics Data System (ADS)

Huang, Jun-Lin; Zhou, Ke-Yi; Wang, Xin-Meng; Tu, Yi-You; Xu, Jian-Qun

2014-07-01

Failure of steam-side oxide scales on boiler tubes can seriously influence the safety of coal-fired power plants. Uniaxial tensile tests employing acoustic emission (AE) monitoring were performed, in this work, to investigate the failure behavior of steam-side oxide scales on T22 alloy boiler superheater tubes. The characteristic frequency spectra of the captured AE signals were obtained by performing fast Fourier transform. Three distinct peak frequency bands, 100-170, 175-250, and 280-390 kHz, encountered in different testing stages were identified in the frequency spectra, which were confirmed to, respectively, correspond to substrate plastic deformation, oxide vertical cracking, and oxide spalling with the aid of scanning electronic microscopy observations, and can thus be used for distinguishing different oxide failure mechanisms. Finally, the critical cracking strain of the oxide scale and the interfacial shear strength of the oxide/substrate interface were estimated, which are the critical parameters urgently desired for modeling the failure behavior of steam-side oxide scales on boiler tubes of coal-fired power plants.

Temporal abundance of Aedes aegypti in Manaus, Brazil, measured by two trap types for adult mosquitoes

PubMed Central

Degener, Carolin Marlen; de Ázara, Tatiana Mingote Ferreira; Roque, Rosemary Aparecida; Codeço, Cláudia Torres; Nobre, Aline Araújo; Ohly, Jörg Johannes; Geier, Martin; Eiras, Álvaro Eduardo

2014-01-01

A longitudinal study was conducted in Manaus, Brazil, to monitor changes of adult Aedes aegypti (L.) abundance. The objectives were to compare mosquito collections of two trap types, to characterise temporal changes of the mosquito population, to investigate the influence of meteorological variables on mosquito collections and to analyse the association between mosquito collections and dengue incidence. Mosquito monitoring was performed fortnightly using MosquiTRAPs (MQT) and BG-Sentinel (BGS) traps between December 2008-June 2010. The two traps revealed opposing temporal infestation patterns, with highest mosquito collections of MQTs during the dry season and highest collections of BGS during the rainy seasons. Several meteorological variables were significant predictors of mosquito collections in the BGS. The best predictor was the relative humidity, lagged two weeks (in a positive relationship). For MQT, only the number of rainy days in the previous week was significant (in a negative relationship). The correlation between monthly dengue incidence and mosquito abundance in BGS and MQT was moderately positive and negative, respectively. Catches of BGS traps reflected better the dynamic of dengue incidence. The findings help to understand the effects of meteorological variables on mosquito infestation indices of two different traps for adult dengue vectors in Manaus. PMID:25494470

The Electronic McPhail Trap

PubMed Central

Potamitis, Ilyas; Rigakis, Iraklis; Fysarakis, Konstantinos

2014-01-01

Certain insects affect cultivations in a detrimental way. A notable case is the olive fruit fly (Bactrocera oleae (Rossi)), that in Europe alone causes billions of euros in crop-loss/per year. Pests can be controlled with aerial and ground bait pesticide sprays, the efficiency of which depends on knowing the time and location of insect infestations as early as possible. The inspection of traps is currently carried out manually. Automatic monitoring traps can enhance efficient monitoring of flying pests by identifying and counting targeted pests as they enter the trap. This work deals with the hardware setup of an insect trap with an embedded optoelectronic sensor that automatically records insects as they fly in the trap. The sensor responsible for detecting the insect is an array of phototransistors receiving light from an infrared LED. The wing-beat recording is based on the interruption of the emitted light due to the partial occlusion from insect's wings as they fly in the trap. We show that the recordings are of high quality paving the way for automatic recognition and transmission of insect detections from the field to a smartphone. This work emphasizes the hardware implementation of the sensor and the detection/counting module giving all necessary implementation details needed to construct it. PMID:25429412

Demonstration and Characterization of a Persistent Pheromone Lure for the Navel Orangeworm, Amyelois transitella (Lepidoptera: Pyralidae).

PubMed

Higbee, Bradley S; Burks, Charles S; Larsen, Thomas E

2014-07-22

The lack of an effective pheromone lure has made it difficult to monitor and manage the navel orangeworm, Amyelois transitella (Lepidoptera: Pyralidae), in the economically important crops in which it is the primary insect pest. A series of experiments was conducted to demonstrate and characterize a practical synthetic pheromone lure for capturing navel orangeworm males. Traps baited with lures prepared with 1 or 2 mg of a three- or four-component formulation captured similar numbers of males. The fluctuation over time in the number of males captured in traps baited with the pheromone lure correlated significantly with males captured in female-baited traps. Traps baited with the pheromone lure usually did not capture as many males as traps baited with unmated females, and the ratio of males trapped with pheromone to males trapped with females varied between crops and with abundance. The pheromone lure described improves the ability of pest managers to detect and monitor navel orangeworm efficiently and may improve management and decrease insecticide treatments applied as a precaution against damage. Awareness of differences between male interaction with the pheromone lure and calling females, as shown in these data, will be important as further studies and experience determine how best to use this lure for pest management.

Demonstration and Characterization of a Persistent Pheromone Lure for the Navel Orangeworm, Amyelois transitella (Lepidoptera: Pyralidae)

PubMed Central

Higbee, Bradley S.; Burks, Charles S.; Larsen, Thomas E.

2014-01-01

The lack of an effective pheromone lure has made it difficult to monitor and manage the navel orangeworm, Amyelois transitella (Lepidoptera: Pyralidae), in the economically important crops in which it is the primary insect pest. A series of experiments was conducted to demonstrate and characterize a practical synthetic pheromone lure for capturing navel orangeworm males. Traps baited with lures prepared with 1 or 2 mg of a three- or four-component formulation captured similar numbers of males. The fluctuation over time in the number of males captured in traps baited with the pheromone lure correlated significantly with males captured in female-baited traps. Traps baited with the pheromone lure usually did not capture as many males as traps baited with unmated females, and the ratio of males trapped with pheromone to males trapped with females varied between crops and with abundance. The pheromone lure described improves the ability of pest managers to detect and monitor navel orangeworm efficiently and may improve management and decrease insecticide treatments applied as a precaution against damage. Awareness of differences between male interaction with the pheromone lure and calling females, as shown in these data, will be important as further studies and experience determine how best to use this lure for pest management. PMID:26462827

PET imaging of β-glucuronidase activity by an activity-based 124I-trapping probe for the personalized glucuronide prodrug targeted therapy.

PubMed

Su, Yu-Cheng; Cheng, Ta-Chun; Leu, Yu-Ling; Roffler, Steve R; Wang, Jaw-Yuan; Chuang, Chih-Hung; Kao, Chien-Han; Chen, Kai-Chuan; Wang, Hsin-Ell; Cheng, Tian-Lu

2014-12-01

Beta-glucuronidase (βG) is a potential biomarker for cancer diagnosis and prodrug therapy. The ability to image βG activity in patients would assist in personalized glucuronide prodrug cancer therapy. However, whole-body imaging of βG activity for medical usage is not yet available. Here, we developed a radioactive βG activity-based trapping probe for positron emission tomography (PET). We generated a (124)I-tyramine-conjugated difluoromethylphenol beta-glucuronide probe (TrapG) to form (124)I-TrapG that could be selectively activated by βG for subsequent attachment of (124)I-tyramine to nucleophilic moieties near βG-expressing sites. We estimated the specificity of a fluorescent FITC-TrapG, the cytotoxicity of tyramine-TrapG, and the serum half-life of (124)I-TrapG. βG targeting of (124)I-TrapG in vivo was examined by micro-PET. The biodistribution of (131)I-TrapG was investigated in different organs. Finally, we imaged the endogenous βG activity and assessed its correlation with therapeutic efficacy of 9-aminocamptothecin glucuronide (9ACG) prodrug in native tumors. FITC-TrapG showed specific trapping at βG-expressing CT26 (CT26/mβG) cells but not in CT26 cells. The native TrapG probe possessed low cytotoxicity. (124)I-TrapG preferentially accumulated in CT26/mβG but not CT26 cells. Meanwhile, micro-PET and whole-body autoradiography results demonstrated that (124)I-TrapG signals in CT26/mβG tumors were 141.4-fold greater than in CT26 tumors. Importantly, Colo205 xenografts in nude mice that express elevated endogenous βG can be monitored by using infrared glucuronide trapping probes (NIR-TrapG) and suppressed by 9ACG prodrug treatment. (124)I-TrapG exhibited low cytotoxicity allowing long-term monitoring of βG activity in vivo to aid in the optimization of prodrug targeted therapy. ©2014 American Association for Cancer Research.

Seasonality and daily activity of male and female tabanid flies monitored in a Hungarian hill-country pasture by new polarization traps and traditional canopy traps.

PubMed

Herczeg, Tamás; Blahó, Miklós; Száz, Dénes; Kriska, György; Gyurkovszky, Mónika; Farkas, Róbert; Horváth, Gábor

2014-11-01

Blood-sucking female tabanid flies cause serious problems for animals and humans. For the control of tabanids, the knowledge about their seasonality and daily activity is of great importance. Earlier, only traditional traps capturing exclusively female tabanids have been used to survey tabanid activity. The data of such temporal trapping do not reflect correctly the activity of male and female tabanid flies. Our major aim was to monitor the trapping numbers of male and female tabanids during a 3-month summer survey in Hungary. We used (i) conventional canopy traps with liquid traps on the ground beneath the canopy and (ii) L-shaped sticky traps with vertical and horizontal components. Our other goal was to compare the efficiencies of the two components of each trap type used. We observed two greater peaks of the trapping number of tabanids. These peaks started with increased catches of female tabanids captured by the canopy traps and the vertical sticky traps and ended with a dominance of male and female tabanids caught by the liquid traps and the horizontal sticky traps. The swarming periods were interrupted by rainy/cool days, when the number of tabanids decreased drastically. Among the 17 species, six dominated and composed 89.4% of the captured tabanids: Haematopota pluvialis, Tabanus tergestinus, Tabanus bromius, Tabanus maculicornis, Tabanus bovinus and Atylotus loewianus. The number of water-seeking male and female tabanids rose up to 12-13 h and then decreased but had a secondary peak at about 17 h. The stochastic weather change and the communities of different species resulted in large standard deviations of the averaged number of tabanids in the course of a day. The horizontally polarizing (liquid and horizontal sticky) traps captured both male and female specimens and were about three times more efficient than the canopy and vertical sticky traps that caught only females. The results of the horizontal sticky traps corresponded to those of the liquid traps, while the catches of the vertical sticky traps corresponded to those of the canopy traps. The catches of the used trap types reflected well the species and water/host-seeking composition of tabanids.

Monitoring oriental fruit moth (Lepidoptera:Tortricidae) with the ajar bait trap in pome and stone fruit orchards under mating disruption

USDA-ARS?s Scientific Manuscript database

Studies in Oregon, California, Pennsylvania, and Italy evaluated the relative performance of the Ajar trap for Grapholita molesta (Busck), in pome and stone fruit orchards treated with sex pheromone dispensers for mating disruption. The Ajar is a delta-shaped trap with a screened jar filled with a t...

Effect of trap type, trap position, time of year, and beetle density on captures of the Redbay Ambrosia Beetle (Coleoptera: Curculionidae: Scolytinae).

Treesearch

James Hanula; Michael Ulyshen; Scott Horn`

2011-01-01

The exotic redbay ambrosia beetle, Xyleborus glabratus Eichhoff (Coleoptera: Curculionidae: Scolytinae), and its fungal symbiont Raffaellea lauricola Harrington, Fraedrich, and Aghayeva are responsible for widespread redbay, Persea borbonia (L.) Spreng., mortality in the southern United States. Effective traps and lures are needed to monitor spread of the beetle and...

Predicting infestation levels of the nantucket pine tip moth (Lepidoptera: Tortricidae) using pheromone traps

Treesearch

Christopher Asaro; C. Wayne Berisford

2001-01-01

There is considerable interest in using pheromone trap catches of the Nantucket pine tip moth, Rhyacionia frustrana (Conistock), to estimate or predict population density and damage. At six sites in the Georgia Piedmont, adult tip moths were monitored through one or more years using pheromone traps while population density and damage for each tip...

Comparison of trapping for eggs, females, and males of the navel orangeworm Amyelois transitella (Walker) in almonds

USDA-ARS?s Scientific Manuscript database

The navel orangeworm is the primary insect pest of almonds in California, and egg traps are the primary means of monitoring this pest. A previous study found that the current use of 2-4 traps per block usually is not sufficient to provide management information specifically for that block. In this s...

Summer trapping method for mule deer. [Nevada Test Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Giles, K.R.

1979-07-01

A summer mule deer trapping method which uses modified Clover traps in a circular corral with water as a bait is described. Drug restraint was used to facilitate safe handling of mule deer by the investigator. Fifteen mule deer were safely captured and outfitted with radio transmitters, ear tags, and reflective markers, and their movements monitored to determine migration patterns.

Use of pheromone traps to predict infestation levels of the nantucket pine tip moth: Can it be done?

Treesearch

Christopher Asaro; C. Wayne Berisford

1999-01-01

Pheromone traps baited with synthetic baits are used in southeastern pine plantations to monitor the phenology of the Nantucket pine tip moth (Rhyacionia frustrana (Comstock)) for timing of insecticide applications. Trap catches of tip moths have been difficult to interpret because they decrease considerably relative to population density from the...

40 CFR 60.4171 - Initial certification and recertification procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... and Compliance Times for Coal-Fired Electric Steam Generating Units Monitoring and Reporting § 60.4171... disapproval under paragraph (c)(3)(iv)(C) of this section. The 120-day review period shall not begin before...

40 CFR 60.4171 - Initial certification and recertification procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... and Compliance Times for Coal-Fired Electric Steam Generating Units Monitoring and Reporting § 60.4171... disapproval under paragraph (c)(3)(iv)(C) of this section. The 120-day review period shall not begin before...

A study revealing the key aroma compounds of steamed bread made by Chinese traditional sourdough*

PubMed Central

Zhang, Guo-hua; Wu, Tao; Sadiq, Faizan A.; Yang, Huan-yi; Liu, Tong-jie; Ruan, Hui; He, Guo-qing

2016-01-01

Aroma of Chinese steamed bread (CSB) is one of the important parameters that determines the overall quality attributes and consumer acceptance. However, the aroma profile of CSB still remains poorly understood, mainly because of relying on only a single method for aroma extraction in previous studies. Therefore, the objective of this study was to determine the volatile aroma compounds of five different samples of CSB using three different aroma extraction methods, namely solid-phase microextraction (SPME), simultaneous distillation–extraction (SDE), and purge and trap (P&T). All samples showed a unique aroma profile, which could be attributed to their unique microbial consortia. (E)-2-Nonenal and (E,E)-2,4-decadienal were the most prevalent aromatic compounds revealed by SDE, which have not been reported previously, while ethanol and acetic acid proved to be the most dominant compounds by both SPME and P&T. Our approach of combining three different aroma extraction methods provided better insights into the aroma profile of CSB, which had remained largely unknown in previous studies. PMID:27704748

High Temperature Monitoring the Height of Condensed Water in Steam Pipes

NASA Technical Reports Server (NTRS)

Bar-Cohen, Yoseph; Lih, Shyh-Shiuh; Badescu, Mircea; Bao, Xiaoqi; Sherrit, Stewart; Widholm, Scott; Ostlund, Patrick; Blosiu, Julian

2011-01-01

An in-service health monitoring system is needed for steam pipes to track through their wall the condensation of water. The system is required to measure the height of the condensed water inside the pipe while operating at temperatures that are as high as 250 deg. C. The system needs to be able to make real time measurements while accounting for the effects of cavitation and wavy water surface. For this purpose, ultrasonic wave in pulse-echo configuration was used and reflected signals were acquired and auto-correlated to remove noise from the data and determine the water height. Transmitting and receiving the waves is done by piezoelectric transducers having Curie temperature that is significantly higher than 250 deg. C. Measurements were made at temperatures as high as 250 deg. C and have shown the feasibility of the test method. This manuscript reports the results of this feasibility study.

Interactive chemistry management system (ICMS); Field demonstration results at United Illuminating

DOE Office of Scientific and Technical Information (OSTI.GOV)

Noto, F.A.; Farrell, D.M.; Lombard, E.V.

1988-01-01

The authors report on a field demonstration of the interactive chemistry management system (ICMS) performed in the late summer of 1987 at the New Haven Harbor Station of United Illuminating Co. This demonstration was the first installation of the ICMS at an actual plant site. The ICMS is a computer-based system designed to monitor, diagnose, and provide optional automatic control of water and steam chemistry throughout the steam generator cycle. It is one of the diagnostic modules that comprises CE-TOPS (combustion engineering total on-line performance system), which continuously monitors operating conditions and suggests priority actions to increase operation efficiency, extendmore » the performance life of boiler components and reduce maintenance costs. By reducing the number of forced outages through early identification of potentially detrimental conditions, diagnosis of possible causes, and execution of corrective actions, improvements in unit availability and reliability will result.« less

Apparatus for and Method of Monitoring Condensed Water in Steam Pipes at High Temperature

NASA Technical Reports Server (NTRS)

Lih, Shyh-Shiuh (Inventor); Bao, Xiaoqi (Inventor); Bar-Cohen, Yoseph (Inventor); Lee, Hyeong Jae (Inventor)

2016-01-01

A system and method for monitoring the properties of a fluid, such as water, in a steam pipe without mechanically penetrating the wall of the pipe. The system uses a piezoelectric transducer to launch an ultrasonic probe signal into the pipe. Reflected ultrasonic signals are captured in a transducer, which can be the same transducer that launched the probe signal. The reflected signals are subjected to data processing, which can include filtering, amplification, analog-to-digital conversion and autocorrelation analysis. A result is extracted which is indicative of a property of the fluid, such as a height of the condensed fluid, a cavitation of the condensed fluid, and a surface perturbation of the condensed fluid. The result can be recorded, displayed, and/or transmitted to another location. One embodiment of the system has been constructed and tested based on a general purpose programmable computer using instructions recorded in machine-readable non-volatile memory.

In-Service Monitoring of Steam Pipe Systems at High Temperatures

NASA Technical Reports Server (NTRS)

Sherrit, Stewart (Inventor); Scott, James Samson (Inventor); Bar-Cohen, Yoseph (Inventor); Badescu, Mircea (Inventor); Widholm, Scott E. (Inventor); Lih, Shyh-Shiuh (Inventor); Bao, Xiaoqi (Inventor); Blosiu, Julian O. (Inventor)

2014-01-01

A system and method for monitoring the properties of a fluid, such as water, in a steam pipe without mechanically penetrating the wall of the pipe. The system uses a piezoelectric transducer to launch an ultrasonic probe signal into the pipe. Reflected ultrasonic signals are captured in a transducer, which can be the same transducer that launched the probe signal. The reflected signals are subjected to data processing, which can include filtering, amplification, analog-to-digital conversion and autocorrelation analysis. A result is extracted which is indicative of a property of the fluid, such as a height of the condensed fluid, a cavitation of the condensed fluid, and a surface perturbation of the condensed fluid. The result can be recorded, displayed, and/or transmitted to another location. One embodiment of the system has been constructed and tested based on a general purpose programmable computer using instructions recorded in machine-readable non-volatile memory.

Characterizing physical properties and heterogeneous chemistry of single particles in air using optical trapping-Raman spectroscopy

NASA Astrophysics Data System (ADS)

Gong, Z.; Wang, C.; Pan, Y. L.; Videen, G.

2017-12-01

Heterogeneous reactions of solid particles in a gaseous environment are of increasing interest; however, most of the heterogeneous chemistry studies of airborne solids were conducted on particle ensembles. A close examination on the heterogeneous chemistry between single particles and gaseous-environment species is the key to elucidate the fundamental mechanisms of hydroscopic growth, cloud nuclei condensation, secondary aerosol formation, etc., and reduce the uncertainty of models in radiative forcing, climate change, and atmospheric chemistry. We demonstrate an optical trapping-Raman spectroscopy (OT-RS) system to study the heterogeneous chemistry of the solid particles in air at single-particle level. Compared to other single-particle techniques, optical trapping offers a non-invasive, flexible, and stable method to isolate single solid particle from substrates. Benefited from two counter-propagating hollow beams, the optical trapping configuration is adaptive to trap a variety of particles with different materials from inorganic substitution (carbon nanotubes, silica, etc.) to organic, dye-doped polymers and bioaerosols (spores, pollen, etc.), with different optical properties from transparent to strongly absorbing, with different sizes from sub-micrometers to tens of microns, or with distinct morphologies from loosely packed nanotubes to microspheres and irregular pollen grains. The particles in the optical trap may stay unchanged, surface degraded, or optically fragmented according to different laser intensity, and their physical and chemical properties are characterized by the Raman spectra and imaging system simultaneously. The Raman spectra is able to distinguish the chemical compositions of different particles, while the synchronized imaging system can resolve their physical properties (sizes, shapes, morphologies, etc.). The temporal behavior of the trapped particles also can be monitored by the OT-RS system at an indefinite time with a resolution from 10 ms to 5 min, which can be further applied to monitor the dynamics of heterogeneous reactions. The OT-RS system provides a flexible method to characterize and monitor the physical properties and heterogeneous chemistry of optically trapped solid particles in gaseous environment at single-particle level.

Optimising Camera Traps for Monitoring Small Mammals

PubMed Central

Glen, Alistair S.; Cockburn, Stuart; Nichols, Margaret; Ekanayake, Jagath; Warburton, Bruce

2013-01-01

Practical techniques are required to monitor invasive animals, which are often cryptic and occur at low density. Camera traps have potential for this purpose, but may have problems detecting and identifying small species. A further challenge is how to standardise the size of each camera’s field of view so capture rates are comparable between different places and times. We investigated the optimal specifications for a low-cost camera trap for small mammals. The factors tested were 1) trigger speed, 2) passive infrared vs. microwave sensor, 3) white vs. infrared flash, and 4) still photographs vs. video. We also tested a new approach to standardise each camera’s field of view. We compared the success rates of four camera trap designs in detecting and taking recognisable photographs of captive stoats ( Mustela erminea ), feral cats (Felis catus) and hedgehogs ( Erinaceus europaeus ). Trigger speeds of 0.2–2.1 s captured photographs of all three target species unless the animal was running at high speed. The camera with a microwave sensor was prone to false triggers, and often failed to trigger when an animal moved in front of it. A white flash produced photographs that were more readily identified to species than those obtained under infrared light. However, a white flash may be more likely to frighten target animals, potentially affecting detection probabilities. Video footage achieved similar success rates to still cameras but required more processing time and computer memory. Placing two camera traps side by side achieved a higher success rate than using a single camera. Camera traps show considerable promise for monitoring invasive mammal control operations. Further research should address how best to standardise the size of each camera’s field of view, maximise the probability that an animal encountering a camera trap will be detected, and eliminate visible or audible cues emitted by camera traps. PMID:23840790

Sorbent-based sampling methods for volatile and semi-volatile organic compounds in air. Part 2. Sorbent selection and other aspects of optimizing air monitoring methods.

PubMed

Woolfenden, Elizabeth

2010-04-16

Sorbent tubes/traps are widely used in combination with gas chromatographic (GC) analytical methods to monitor the vapour-phase fraction of organic compounds in air. Applications range from atmospheric research and ambient air monitoring (indoor and outdoor) to occupational hygiene (personal exposure assessment) and measuring chemical emission levels. Part 1 of this paper reviewed the main sorbent-based air sampling strategies including active (pumped) tube monitoring, diffusive (passive) sampling onto sorbent tubes/cartridges plus sorbent trapping/focusing of whole air samples that are either collected in containers (such as canisters or bags) or monitored online. Options for subsequent extraction and transfer to GC(MS) analysis were also summarised and the trend to thermal desorption (TD)-based methods and away from solvent extraction was explained. As a result of this trend, demand for TD-compatible sorbents (alternatives to traditional charcoal) is growing. Part 2 of this paper therefore continues with a summary of TD-compatible sorbents, their respective advantages and limitations and considerations for sorbent selection. Other analytical considerations for optimizing sorbent-based air monitoring methods are also discussed together with recent technical developments and sampling accessories which have extended the application range of sorbent trapping technology generally. Copyright 2010 Elsevier B.V. All rights reserved.

An evaluation of western bean cutworm pheromone trapping techniques (Lepidoptera: Noctuidae) in a corn and soybean agroecosystem.

PubMed

Dorhout, David L; Rice, Marlin E

2008-04-01

Pheromone traps can be used to monitor for adult western bean cutworms, Striacosta albicosta (Smith) (Lepidoptera: Noctuidae), and for the timing of field scouting. Understanding the effect that different trapping techniques have on adult captures could help corn (Zea mays L.) producers make better pest management decisions. Several approaches to trapping adults were evaluated in 2005 and 2006 by using two different pheromone traps (sticky wing and jug traps) in two different environments (corn or corn/soybean [Glycine max (L.) Merr.] at three different heights (0.6, 1.2, and 1.8 m). There was no significant difference in the trap catches by trap type in either 2005 or 2006. There were significantly more adults captured in traps placed between two cornfields than traps placed between corn/soybean fields during both years. Trap height also was significant, with the traps at 1.2 and 1.8 m catching more moths than traps at 0.6 m during both years. These results show that trapping techniques do affect trap catches and that either trap type placed between two cornfields at either 1.2 or 1.8 m above the ground will maximize trap catches.

Inconel 690 is alloy of choice for steam-generator tubing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Strauss, S.D.

1996-02-01

The product of two decades of research and plant application, Inconel 690 promises superior long-term resistance to tube cracking in comparison to alloy 600. Ongoing steam-generator management techniques applied at nuclear pressurized-water-reactor (PWR) plants focus on tube monitoring, inspection, and repair, and on water-chemistry control. Of greatest concern to owner/operators of steam generators (SGs) with recirculating (U-bend) rather than straight through tubes is corrosion of several forms, including pitting, thinning, and cracking. As problems persist and operating and maintenance (O and M) costs become prohibitive, managers must consider the remaining option: complete or partial SG replacement. Although replacement costs canmore » range upward of $100-million, this step restores full-power operation, simplifies inspection, shortens subsequent outages, increases unit availability, and reduces radiation exposure of maintenance personnel. Taken together, these can lead to economies over the long term.« less

New-onset asthma after exposure to the steam system additive 2-diethylaminoethanol. A descriptive study.

PubMed

Gadon, M E; Melius, J M; McDonald, G J; Orgel, D

1994-06-01

Through a leak in the steam heating system, the anticorrosive agent 2-diethylaminoethanol was released into the air of a large office building. Irritative symptoms were experienced by most of the 2500 employees, and 14 workers developed asthma within 3 months of exposure. This study was undertaken to review clinical characteristics of these asthmatics. Environmental exposure monitoring data and medical records were reviewed. Seven of 14 cases were defined as "confirmed" and 7 of 14 as "suspect," using the National Institute for Occupational Safety and Health surveillance case definition of occupational asthma. Spirometry was positive in 4 of 14 of the cases and peak flow testing in 10 of 14. Three cases were diagnosed on the basis of work-related symptoms and physical examination alone. The study suggests that acute exposure to the irritating steam additive 2-diethylaminoethanol was a contributing factor in the development of clinical asthma in this population.

A novel technique to control high temperature materials degradation in fossil plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gonzalez-Rodriguez, J.G.; Porcayo-Calderon, J.; Martinez-Villafane, A.

1995-11-01

High temperature corrosion of superheater (SH) and, specially, reheater (RH) is strongly dependent on metal temperature. In this work, a way to continuously monitor the metal temperature of SH or RH, elements developed by the Instituto de Investigaciones Electricas (IIE) is described and the effects of operating parameters on metal temperature are evaluated. Also, the effects the steam-generator design and metal temperature on the corrosion rates have been investigated. In some steam generators, corrosion rates were reduced from 0.7 to 0.2 mm/y by changing the tube material and reducing the metal temperature. Also, the effect of metal temperature on themore » residual life of a 347H tube in a 158MW steam generator is evaluated. It is concluded that metal temperature is the most important parameter in controlling the high-temperature materials behavior in boiler environments.« less

Hemodialysis dialyzers contribute to contamination of air microemboli that bypass the alarm system in the air trap.

PubMed

Stegmayr, C; Jonsson, P; Forsberg, U; Stegmayr, B

2008-04-01

Previous studies have shown that micrometer-sized air bubbles are introduced into the patient during hemodialysis. The aim of this study was to investigate, in vitro, the influence of dialysis filters on the generation of air bubbles. Three different kind of dialyzers were tested: one high-flux FX80 dry filter (Fresenius Medical Care AG&Co. KGaA, Bad Homburg, Germany), one low-flux F8HPS dry filter (Fresenius Medical Care AG&Co. KGaA, Bad Homburg, Germany) and a wet-stored APS-18u filter (Asahi Kasei Medical, Tokyo, Japan). The F8HPS was tested with pump flow ranging between 100 to 400 ml/min. The three filters were compared using a constant pump flow of 300 ml/min. Measurements were performed using an ultrasound Doppler instrument. In 90% of the series, bubbles were measured after the outlet line of the air trap without triggering an alarm. There were significantly more bubbles downstream than upstream of the filters F8HPS and FX80, while there was a significant reduction using the APS-18u. There was no reduction in the number of bubbles after passage through the air trap versus before the air trap (after the dialyzer). Increased priming volume reduced the extent of bubbles in the system. Data indicate that the air trap does not prevent air microemboli from entering the venous outlet part of the dialysis tubing (entry to the patient). More extended priming of the dialysis circuit may reduce the extent of microemboli that originate from dialysis filters. A wet filter may be favorable instead of dry-steam sterilized filters.

Evaluation of monitoring traps with novel bait for navel orangeworm (Lepidoptera: Pyralidae) in California almond and pistachio orchards.

PubMed

Nay, Justin E; Peterson, Elonce M; Boyd, Elizabeth A

2012-08-01

Experiments conducted in three almond, Prunus dulcis (Rosales: Rosaceae), orchards and three pistachio, Pistacia vera (Sapindales: Anicardiaceae), orchards in 2009 and 2010, and determined that sticky bottom wing traps baited with ground pistachio mummies, or a combination of ground pistachio plus ground almond mummies, trapped more adult female navel orangeworm, Amyelois transitella (Walker) (Lepidoptera: Pyralidae), than did traps baited with ground almond mummies alone. During both years of this study, 2.9 and 1.8 more moths were caught in traps baited with pistachio mummies compared with traps baited with almond mummies in almond orchards and pistachio orchards, respectively. Also, traps located in pistachio orchards caught 5.9 and 8.3 times more navel orangeworm than were trapped from almond orchards in 2009 and 2010, respectively. Implications for use of this novel baited trap in almond and pistachio orchard integrated pest management programs are discussed.

Integrated environmental monitoring and multivariate data analysis-A case study.

PubMed

Eide, Ingvar; Westad, Frank; Nilssen, Ingunn; de Freitas, Felipe Sales; Dos Santos, Natalia Gomes; Dos Santos, Francisco; Cabral, Marcelo Montenegro; Bicego, Marcia Caruso; Figueira, Rubens; Johnsen, Ståle

2017-03-01

The present article describes integration of environmental monitoring and discharge data and interpretation using multivariate statistics, principal component analysis (PCA), and partial least squares (PLS) regression. The monitoring was carried out at the Peregrino oil field off the coast of Brazil. One sensor platform and 3 sediment traps were placed on the seabed. The sensors measured current speed and direction, turbidity, temperature, and conductivity. The sediment trap samples were used to determine suspended particulate matter that was characterized with respect to a number of chemical parameters (26 alkanes, 16 PAHs, N, C, calcium carbonate, and Ba). Data on discharges of drill cuttings and water-based drilling fluid were provided on a daily basis. The monitoring was carried out during 7 campaigns from June 2010 to October 2012, each lasting 2 to 3 months due to the capacity of the sediment traps. The data from the campaigns were preprocessed, combined, and interpreted using multivariate statistics. No systematic difference could be observed between campaigns or traps despite the fact that the first campaign was carried out before drilling, and 1 of 3 sediment traps was located in an area not expected to be influenced by the discharges. There was a strong covariation between suspended particulate matter and total N and organic C suggesting that the majority of the sediment samples had a natural and biogenic origin. Furthermore, the multivariate regression showed no correlation between discharges of drill cuttings and sediment trap or turbidity data taking current speed and direction into consideration. Because of this lack of correlation with discharges from the drilling location, a more detailed evaluation of chemical indicators providing information about origin was carried out in addition to numerical modeling of dispersion and deposition. The chemical indicators and the modeling of dispersion and deposition support the conclusions from the multivariate statistics. Integr Environ Assess Manag 2017;13:387-395. © 2016 SETAC. © 2016 SETAC.

Nuclear Submarines and Aircraft Carriers | Radiation ...

EPA Pesticide Factsheets

2017-08-07

Nuclear submarines and aircraft carriers are powered by onboard nuclear reactors. Heat from the nuclear reaction makes the steam needed to power the submarine. When a nuclear vessel is taken out of service, its radioactive parts are disposed of and monitored.

Field evaluation of effect of temperature on release of Disparlure from a pheromone-baited trapping system used to monitor gypsy moth (Lepidoptera: Lymantriidae)

Treesearch

Patrick C. Tobin; Aijun Zhang; Ksenia Onufrieva; Donna Leonard

2011-01-01

Traps baited with disparlure, the synthetic form of the gypsy moth, Lymantria dispar (L.) (Lepidoptera: Lymantriidae), sex pheromone are used to detect newly founded populations and estimate population density across the United States. The lures used in trapping devices are exposed to field conditions with varying climates, which can affect the rate...

Evaluation of funnel traps for characterizing the bark beetle (Coleoptera: Scolytidae) communities in ponderosa pine forests of North-Central Arizona

Treesearch

Christopher J. Hayes; Tom E. DeGomez; Karen M. Clancy; Kelly K. Williams; Joel D. McMillin; John A. Anhold

2008-01-01

Lindgren funnel traps baited with aggregation pheromones are widely used to monitor and manage populations of economically important bark beetles (Coleoptera: Scolytidae). This study was designed to advance our understanding of how funnel trap catches assess bark beetle communities and relative abundance of individual species. In the second year (2005) of a 3-yr study...

Traps and attractants for wood-boring insects in ponderosa pine stands in the Black Hills, South Dakota

Treesearch

Sheryl L. Costello; Jose F. Negron; William R. Jacobi

2008-01-01

Recent large-scale wildfires have increased populations of wood-boring insects in the Black Hills of South Dakota. Because little is known about possible impacts of wood-boring insects in the Black Hills, land managers are interested in developing monitoring techniques such as flight trapping with semiochemical baits. Two trap designs and four semiochemical attractants...

Efficacy of traps, lures, and repellents for Xylosandrus compactus (Coleoptera: Curculionidae) and other ambrosia beetles on Coffea arabica plantations and Acacia koa nurseries in Hawaii

Treesearch

E. G. Burbano; M.G. Wright; N.E. Gillette; S. Mori; N. Dudley; N. Jones; M. Kaufmann

2012-01-01

The black twig borer, Xylosandrus compactus (Eichhoff) (Coleoptera: Curculionidae: Scolytinae), is a pest of coffee and many endemic Hawaiian plants. Traps baited with chemical attractants commonly are used to capture ambrosia beetles for purposes of monitoring, studying population dynamics, predicting outbreaks, and mass trapping to reduce damage...

Field Comparisons of the Gravid Aedes Trap (GAT) and BG-Sentinel Trap for Monitoring Aedes albopictus (Diptera: Culicidae) Populations and Notes on Indoor GAT Collections in Vietnam.

PubMed

Johnson, Brian J; Hurst, Tim; Quoc, Hung Luu; Unlu, Isik; Freebairn, Christopher; Faraji, Ary; Ritchie, Scott A

2017-03-01

We report on the use of the Gravid Aedes Trap (GAT) as a surveillance device for Aedes albopictus (Skuse) relative to the BG-Sentinel (BGS) trap in field studies conducted in Trenton, NJ, and on Hammond Island, Queensland, Australia. A parallel study conducted in Nha Trang, Vietnam, assessed the use of the GAT as an indoor surveillance device as well as the use of canola oil as a noninsecticide killing agent. In Trenton and Hammond Island, the GAT collected fewer male (0.40 ± 0.12 and 0.43 ± 0.30, respectively) and female (3.05 ± 0.67 and 2.7 ± 2.3, respectively) Ae. albopictus than the BGS trap (males: 3.54 ± 1.26 and 3.75 ± 0.83; females: 4.66 ± 1.18 and 3.9 ± 0.23) over their respective sampling periods (i.e., 24 h for the BGS and 1 wk for the GAT). Despite differences in capture rates, the percentage of traps positive for female Ae. albopictus was similar between the BGS and GAT (Trenton: 60.1 ± 6.3% and 64.4 ± 4.1%; Hammond: 87.5 ± 6.9% and 80.0 ± 8.2%). In Nha Trang, the GAT was equally effective indoors and outdoors with (10 g hay or 3 g fish food) and without (water or empty) infusion. Additionally, no significant decrease in collections was observed between GATs set with canola oil or long-lasting insecticidal net. In summary, both traps were successful in monitoring female Ae. albopictus over their respective trapping intervals, but would be best used to complement each other to monitor both sexes and all physiological stages of female Ae. albopictus. However, the versatility and low-cost of the GAT makes it an attractive alternative to the more expensive BGS trap. © The Authors 2016. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Monitoring populations of saddled prominent (Lepidoptera: Notodontidae) with pheromone-baited traps.

PubMed

Spear-O'Mara, Jennifer; Allen, Douglas C

2007-04-01

Field trials with three types of pheromone traps were performed in eight northern hardwood stands in northern New York state to develop a population-monitoring tool for the saddled prominent, Heterocampa guttivitta (Walker) (Lepidoptera: Notodontidae). Lure specificity and the relationship between pheromone trap catch and subsequent egg density were examined. A study of moth emergence in relation to temperature was designed to determine whether moth activity throughout the flight season can be predicted using a growing degree-day (DD) model. Pherocon 1C wing traps were significantly more effective than the green Unitrap bucket style. Catch was not affected by position when traps were > or =20 m from an opening (road), and lures were specific to saddled prominent. Lure specificity was examined using green Multipher bucket traps, which effectively attracted and held moths. In the first year of the study, number of viable eggs per 10 leaf clusters was significantly correlated (r2 = 0.59) with average moth catch/trap in pheromone-baited Pherocon traps. When differences in stand density (basal area) and relative abundance of sugar maple (percentage of total stems per hectare), the principle host, were accounted for, the multiple regression model also was significant and r2 = 0. 83. Neither model, however, was significant the second year. Using a base temperature of 5.5 degrees C and on-site temperature data, the peak of moth flight occurred at 316 +/- 8 DD and end of flight occurred at 533 +/- 9 DD.

Evaluation of trap types and food attractants for Rhagoletis cerasi (Diptera: Tephritidae).

PubMed

Katsoyannos, B I; Papadopoulos, N T; Stavridis, D

2000-06-01

Trapping experiments were conducted during the period of flight activity of the cherry fruit fly Rhagoletis cerasi L. in the area of Thessaloniki, northern Greece, during the years 1993-1997 to test several traps alone and in combination with different food attractants. Yellow sticky-coated visual traps were more effective than McPhail-type traps baited with different food attractants. Of the visual traps, the most effective was the yellow Rebell trap. The Rebell trap, provided with a dispenser containing a slow release formulation of ammonium acetate attached to the lower part of the trap, was found to be the most effective of all treatments tested, capturing approximately 50% more R. cerasi flies than the Rebell trap without any attractant. Ammonium carbonate dispensers did not increase the performance of Rebell traps. More mature females were captured in Rebell traps baited with or without ammonium acetate than in McPhail-type traps baited with ammonium acetate. This study demonstrates that Rebell traps baited with an ammonium acetate dispenser can provide a more effective tool for monitoring and mass trapping of R. cerasi than the currently used unbaited Rebell traps.

Assessing the potential of reservoir outflow management to reduce sedimentation using continuous turbidity monitoring and reservoir modelling

USGS Publications Warehouse

Lee, Casey; Foster, Guy

2013-01-01

In-stream sensors are increasingly deployed as part of ambient water quality-monitoring networks. Temporally dense data from these networks can be used to better understand the transport of constituents through streams, lakes or reservoirs. Data from existing, continuously recording in-stream flow and water quality monitoring stations were coupled with the two-dimensional hydrodynamic CE-QUAL-W2 model to assess the potential of altered reservoir outflow management to reduce sediment trapping in John Redmond Reservoir, located in east-central Kansas. Monitoring stations upstream and downstream from the reservoir were used to estimate 5.6 million metric tons of sediment transported to John Redmond Reservoir from 2007 through 2010, 88% of which was trapped within the reservoir. The two-dimensional model was used to estimate the residence time of 55 equal-volume releases from the reservoir; sediment trapping for these releases varied from 48% to 97%. Smaller trapping efficiencies were observed when the reservoir was maintained near the normal operating capacity (relative to higher flood pool levels) and when average residence times were relatively short. An idealized, alternative outflow management scenario was constructed, which minimized reservoir elevations and the length of time water was in the reservoir, while continuing to meet downstream flood control end points identified in the reservoir water control manual. The alternative scenario is projected to reduce sediment trapping in the reservoir by approximately 3%, preventing approximately 45 000 metric tons of sediment from being deposited within the reservoir annually. This article presents an approach to quantify the potential of reservoir management using existing in-stream data; actual management decisions need to consider the effects on other reservoir benefits, such as downstream flood control and aquatic life.

Focal Hydrothermal Ablation: Preliminary Investigation of a New Concept

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roy, Sumit, E-mail: sumit.roy@online.no

2013-08-01

PurposeTo determine whether focal tissue ablation is possible with interstitial instillation of steam.MethodsFresh swine livers were used. Through a 20 gauge needle, steam was instilled every 5 s, 3 (n = 5), 6 (n = 5), 9 (n = 5), or 12 (n = 5 + 5) times in a liver lobe. The ablated zones were sectioned parallel (n = 20) or perpendicular (n = 5) to the needle track. The longitudinal long and short axis diameters, or transverse long and short axis diameters of areas with discoloration on macroscopic examination, were measured. The experiment was repeated in vivo onmore » a pig. Steam instillation was performed once every 5 s for 5 min in the liver (n = 3) and in muscle (n = 4), and temperature changes at three neighboring sites were monitored. Long and short axis diameters of the discolored areas were measured.ResultsA well-defined area of discoloration was invariably present at the site of steam instillation. The median longitudinal long axis diameter were 2.0, 2.5, 2.5, and 3.5 cm for 3, 6, 9, and 12 steam instillations in vitro, while median short axis diameters were 1.0, 1.5, 1.5, and 1.5 cm, respectively. Six attempts at ablation in vivo could be successfully completed. The long axis diameters of the ablated zones in the liver were 7.0 and 8.0 cm, while in muscle it ranged from 5.5 to 7.0 cm.ConclusionInstillation of steam in the liver in vitro and in vivo, and in muscle in vivo rapidly leads to circumscribed zones of coagulation necrosis.« less

Integration of laser trapping for continuous and selective monitoring of photothermal response of a single microparticle.

PubMed

Vasudevan, Srivathsan; Chen, George C K; Ahluwalia, Balpreet Singh

2008-12-01

Photothermal response (PTR) is an established pump and probe technique for real-time sensing of biological assays. Continuous and selective PTR monitoring is difficult owing to the Brownian motion changing the relative position of the target with respect to the beams. Integration of laser trapping with PTR is proposed as a solution. The proposed method is verified on red polystyrene microparticles. PTR is continuously monitored for 30 min. Results show that the mean relaxation time variation of the acquired signals is less than 5%. The proposed method is then applied to human red blood cells for continuous and selective PTR.

High Resolution Rapid Revisits Insar Monitoring of Surface Deformation

NASA Astrophysics Data System (ADS)

Singhroy, V.; Li, J.; Charbonneau, F.

2014-12-01

Monitoring surface deformation on strategic energy and transportation corridors requires high resolution spatial and temporal InSAR images for mitigation and safety purposes. High resolution air photos, lidar and other satellite images are very useful in areas where the landslides can be fatal. Recently, radar interferometry (InSAR) techniques using more rapid revisit images from several radar satellites are increasingly being used in active deformation monitoring. The Canadian RADARSAT Constellation (RCM) is a three-satellite mission that will provide rapid revisits of four days interferometric (InSAR) capabilities that will be very useful for complex deformation monitoring. For instance, the monitoring of surface deformation due to permafrost activity, complex rock slide motion and steam assisted oil extraction will benefit from this new rapid revisit capability. This paper provide examples of how the high resolution (1-3 m) rapid revisit InSAR capabilities will improve our monitoring of surface deformation and provide insights in understanding triggering mechanisms. We analysed over a hundred high resolution InSAR images over a two year period on three geologically different sites with various configurations of topography, geomorphology, and geology conditions. We show from our analysis that the more frequent InSAR acquisitions are providing more information in understanding the rates of movement and failure process of permafrost triggered retrogressive thaw flows; the complex motion of an asymmetrical wedge failure of an active rock slide and the identification of over pressure zones related to oil extraction using steam injection. Keywords: High resolution, InSAR, rapid revisits, triggering mechanisms, oil extraction.

A New Visual Trap for Rhagoletis cerasi (L.) (Diptera: Tephritidae).

PubMed

Daniel, Claudia; Mathis, Samuel; Feichtinger, Georg

2014-07-18

The European cherry fruit fly, Rhagoletis cerasi (L.) (Diptera: Tephritidae), is the most important pest of sweet cherries in Europe. The aim of our experiments was to develop a new, cost-efficient, lead chromate-free and more eco-friendly trap for monitoring and mass trapping of R. cerasi. Five different-colored yellow panels and three different trap shapes were compared to a standard Rebell(®) amarillo trap in three experimental orchards in 2012. Trap color F, with a strong increase in reflectance at 500-550 nm and a secondary peak in the UV-region at 300-400 nm, captured significantly more flies than the standard Rebell(®) amarillo trap. Yellow traps with increased reflectance in the blue region (400-500 nm) were least attractive. Trap shape was of minor importance, as long as the object was three-dimensional and visible from all directions. Based on economic and practical considerations, a cylinder-shaped trap "UFA-Samen Kirschenfliegenfalle" was developed for commercial use and is currently under on-farm evaluation.

A new approach to determine the capture conditions of bark beetles in pheromone-baited traps

PubMed Central

Ozcan, Gonca Ece; Cicek, Osman; Enez, Korhan; Yildiz, Mustafa

2014-01-01

Forests form an organic unity with a great number of organic and inorganic components and tend to maintain the sustainability of their existing balance. However, some factors which adversely affect the balance of nature may interrupt this sustainability. The epidemic which is formed by bark beetles in their spreading region, due to various factors, changes the stability so much that interference is required. One of the most common methods used to monitor these beetles is pheromone-baited traps. The recognition of parameters, such as date (day/month/year), temperature and humidity, when bark beetles are captured in pheromone-baited traps, especially those used for monitoring will help to increase the trap efficiency on land and to develop an effective strategy for combating pests. In this study, an electronic control unit was added to pheromone-baited traps in order to obtain all of the above mentioned parameters. This unit operates with microcontrollers and data related to the parameters is saved in a storage unit. This is triggered by the beetle at the moment it is captured in the trap. A photovoltaic system was used to meet the energy needed for the system functioning and to complete the counting process in due time. PMID:26019592

Sorbent-based sampling methods for volatile and semi-volatile organic compounds in air Part 1: Sorbent-based air monitoring options.

PubMed

Woolfenden, Elizabeth

2010-04-16

Sorbent tubes/traps are widely used in combination with gas chromatographic (GC) analytical methods to monitor the vapour-phase fraction of organic compounds in air. Target compounds range in volatility from acetylene and freons to phthalates and PCBs and include apolar, polar and reactive species. Airborne vapour concentrations will vary depending on the nature of the location, nearby pollution sources, weather conditions, etc. Levels can range from low percent concentrations in stack and vent emissions to low part per trillion (ppt) levels in ultra-clean outdoor locations. Hundreds, even thousands of different compounds may be present in any given atmosphere. GC is commonly used in combination with mass spectrometry (MS) detection especially for environmental monitoring or for screening uncharacterised workplace atmospheres. Given the complexity and variability of organic vapours in air, no one sampling approach suits every monitoring scenario. A variety of different sampling strategies and sorbent media have been developed to address specific applications. Key sorbent-based examples include: active (pumped) sampling onto tubes packed with one or more sorbents held at ambient temperature; diffusive (passive) sampling onto sorbent tubes/cartridges; on-line sampling of air/gas streams into cooled sorbent traps; and transfer of air samples from containers (canisters, Tedlar) bags, etc.) into cooled sorbent focusing traps. Whichever sampling approach is selected, subsequent analysis almost always involves either solvent extraction or thermal desorption (TD) prior to GC(/MS) analysis. The overall performance of the air monitoring method will depend heavily on appropriate selection of key sampling and analytical parameters. This comprehensive review of air monitoring using sorbent tubes/traps is divided into 2 parts. (1) Sorbent-based air sampling option. (2) Sorbent selection and other aspects of optimizing sorbent-based air monitoring methods. The paper presents current state-of-the-art and recent developments in relevant areas such as sorbent research, sampler design, enhanced approaches to analytical quality assurance and on-tube derivatisation. Copyright 2009 Elsevier B.V. All rights reserved.

Evaluation of seven aquatic sampling methods for amphibians and other aquatic fauna

USGS Publications Warehouse

Gunzburger, M.S.

2007-01-01

To design effective and efficient research and monitoring programs researchers must have a thorough understanding of the capabilities and limitations of their sampling methods. Few direct comparative studies exist for aquatic sampling methods for amphibians. The objective of this study was to simultaneously employ seven aquatic sampling methods in 10 wetlands to compare amphibian species richness and number of individuals detected with each method. Four sampling methods allowed counts of individuals (metal dipnet, D-frame dipnet, box trap, crayfish trap), whereas the other three methods allowed detection of species (visual encounter, aural, and froglogger). Amphibian species richness was greatest with froglogger, box trap, and aural samples. For anuran species, the sampling methods by which each life stage was detected was related to relative length of larval and breeding periods and tadpole size. Detection probability of amphibians varied across sampling methods. Box trap sampling resulted in the most precise amphibian count, but the precision of all four count-based methods was low (coefficient of variation > 145 for all methods). The efficacy of the four count sampling methods at sampling fish and aquatic invertebrates was also analyzed because these predatory taxa are known to be important predictors of amphibian habitat distribution. Species richness and counts were similar for fish with the four methods, whereas invertebrate species richness and counts were greatest in box traps. An effective wetland amphibian monitoring program in the southeastern United States should include multiple sampling methods to obtain the most accurate assessment of species community composition at each site. The combined use of frogloggers, crayfish traps, and dipnets may be the most efficient and effective amphibian monitoring protocol. ?? 2007 Brill Academic Publishers.

Behavioral Response of the Brown Marmorated Stink Bug (Hemiptera: Pentatomidae) to Semiochemicals Deployed Inside and Outside Anthropogenic Structures During the Overwintering Period.

PubMed

Morrison, William R; Acebes-Doria, Angelita; Ogburn, Emily; Kuhar, Thomas P; Walgenbach, James F; Bergh, J Christopher; Nottingham, Louis; Dimeglio, Anthony; Hipkins, Patricia; Leskey, Tracy C

2017-06-01

The brown marmorated stink bug, Halyomorpha halys (Stål), is an invasive species from Asia capable of causing severe agricultural damage. It can also be a nuisance pest when it enters and exits anthropogenic overwintering sites. In recent years, pheromone lures and traps for H. halys have been developed and used to monitor populations in field studies. To date, no study has investigated the applicability of these monitoring tools for use indoors by building residents during the overwintering period. Herein, we 1) assessed when in late winter (diapause) and spring (postdiapause) H. halys begins to respond to its pheromone (10,11-epoxy-1-bisabolen-3-ol), 2) evaluated whether pheromone-based tools can be used reliably for monitoring H. halys adults in unheated and heated buildings, and 3) elucidated the potential for indoor management using pheromone-baited traps. A 2-yr trapping study suggested that H. halys began to respond reliably to pheromone-baited traps after a critical photoperiod of 13.5 h in the spring. Captures before that point were not correlated with visual counts of bugs in buildings despite robust populations, suggesting currently available pheromone-baited traps were ineffective for surveillance of diapausing H. halys. Finally, because baited traps captured only 8-20% of the adult H. halys known to be present per location, they were not an effective indoor management tool for overwintering H. halys. Our study contributes important knowledge about the capacity of H. halys to perceive its pheromone during overwintering, and the ramifications thereof for building residents with nuisance problems. Published by Oxford University Press on behalf of Entomological Society of America 2017. This work is written by US Government employees and is in the public domain in the US.

Real-time dual-loop electric current measurement for label-free nanofluidic preconcentration chip.

PubMed

Chung, Pei-Shan; Fan, Yu-Jui; Sheen, Horn-Jiunn; Tian, Wei-Cheng

2015-01-07

An electrokinetic trapping (EKT)-based nanofluidic preconcentration device with the capability of label-free monitoring trapped biomolecules through real-time dual-loop electric current measurement was demonstrated. Universal current-voltage (I-V) curves of EKT-based preconcentration devices, consisting of two microchannels connected by ion-selective channels, are presented for functional validation and optimal operation; universal onset current curves indicating the appearance of the EKT mechanism serve as a confirmation of the concentrating action. The EKT mechanism and the dissimilarity in the current curves related to the volume flow rate (Q), diffusion coefficient (D), and diffusion layer (DL) thickness were explained by a control volume model with a five-stage preconcentration process. Different behaviors of the trapped molecular plug were categorized based on four modes associated with different degrees of electroosmotic instability (EOI). A label-free approach to preconcentrating (bio)molecules and monitoring the multibehavior molecular plug was demonstrated through real-time electric current monitoring, rather than through the use of microscope images.

On-Line Monitoring and Diagnostics of the Integrity of Nuclear Plant Steam Generators and Heat Exchangers, Volumes 1, 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Upadhyaya, Belle R.; Hines, J. Wesley; Lu, Baofu

2005-06-03

The overall purpose of this Nuclear Engineering Education Research (NEER) project was to integrate new, innovative, and existing technologies to develop a fault diagnostics and characterization system for nuclear plant steam generators (SG) and heat exchangers (HX). Issues related to system level degradation of SG and HX tubing, including tube fouling, performance under reduced heat transfer area, and the damage caused by stress corrosion cracking, are the important factors that influence overall plant operation, maintenance, and economic viability of nuclear power systems. The research at The University of Tennessee focused on the development of techniques for monitoring process and structuralmore » integrity of steam generators and heat exchangers. The objectives of the project were accomplished by the completion of the following tasks. All the objectives were accomplished during the project period. This report summarizes the research and development activities, results, and accomplishments during June 2001 September 2004. Development and testing of a high-fidelity nodal model of a U-tube steam generator (UTSG) to simulate the effects of fouling and to generate a database representing normal and degraded process conditions. Application of the group method of data handling (GMDH) method for process variable prediction. Development of a laboratory test module to simulate particulate fouling of HX tubes and its effect on overall thermal resistance. Application of the GMDH technique to predict HX fluid temperatures, and to compare with the calculated thermal resistance.Development of a hybrid modeling technique for process diagnosis and its evaluation using laboratory heat exchanger test data. Development and testing of a sensor suite using piezo-electric devices for monitoring structural integrity of both flat plates (beams) and tubing. Experiments were performed in air, and in water with and without bubbly flow. Development of advanced signal processing methods using wavelet transforms and image processing techniques for isolating flaw types. Development and implementation of a new nonlinear and non-stationary signal processing method, called the Hilbert-Huang transform (HHT), for flaw detection and location. This is a more robust and adaptive approach compared to the wavelet transform.Implementation of a moving-window technique in the time domain for detecting and quantifying flaw types in tubular structures. A window zooming technique was also developed for flaw location in tubes. Theoretical study of elastic wave propagation (longitudinal and shear waves) in metallic flat plates and tubing with and without flaws. Simulation of the Lamb wave propagation using the finite-element code ABAQUS. This enabled the verification of the experimental results. The research tasks included both analytical research and experimental studies. The experimental results helped to enhance the robustness of fault monitoring methods and to provide a systematic verification of the analytical results. The results of this research were disseminated in scientific meetings. The journal manuscript titled, "Structural Integrity Monitoring of Steam generator Tubing Using Transient Acoustic Signal Analysis," was published in IEEE Trasactions on Nuclear Science, Vol. 52, No. 1, February 2005. The new findings of this research have potential applications in aerospace and civil structures. The report contains a complete bibliography that was developed during the course of the project.« less

Evaluation of Four Bed Bug Traps for Surveillance of the Brown Dog Tick (Acari: Ixodidae).

PubMed

Carnohan, Lucas P; Kaufman, Phillip E; Allan, Sandra A; Gezan, Salvador A; Weeks, Emma N I

2015-03-01

The brown dog tick, Rhipicephalus sanguineus (Latrielle), can be a serious residential pest due to its unique ability, among ticks, to complete its lifecycle indoors. A single engorged and fertilized female tick can oviposit around 4,000 eggs, allowing indoor establishment to be rapid and easy to miss in early-stage infestations. Acaricide treatment is currently the primary method of control, but can be costly and can lead to the development of acaricide resistance in tick populations. Traps of various designs can be used to help monitor and manage populations of indoor pests, such as cockroaches and bed bugs, but there are currently no commercially available traps for use with brown dog tick infestations. This study included a comparison of four commercially available bed bug traps (NightWatch [BioSensory Inc., Putnam, CT], Bed Bug Beacon [PackTite, Fort Collins, CO], ClimbUp [Susan McKnight Inc., Memphis, TN], and Verify [FMC Corporation, Philadelphia, PA]) with regard to their efficacy in capturing brown dog ticks, and also compared tick attraction to ClimbUp traps baited with several stimuli including CO2. Significantly more ticks were captured and attracted to the NightWatch and CO2-baited ClimbUp traps than the other two trap models. The results suggest that bed bug traps may be useful in brown dog tick monitoring, and CO2 will likely be an important component of a trapping system employed in the future. Published by Oxford University Press on behalf of Entomological Society of America 2015. This work is written by US Government employees and is in the public domain in the US.

Nonlinearity and seasonal bias in an index of brushtail possum abundance

USGS Publications Warehouse

Forsyth, D.M.; Link, W.A.; Webster, R.; Nugent, G.; Warburton, B.

2005-01-01

Introduced brushtail possums (Trichosurus vulpecula) are a widespread pest of conservation and agriculture in New Zealand, and considerable effort has been expended controlling populations to low densities. A national protocol for monitoring the abundance of possums, termed trap catch index (TCI), was adopted in 1996. The TCI requires that lines of leghold traps set at 20-m spacing are randomly located in a management area. The traps are set for 3 fine nights and checked daily, and possums are killed and traps reset. The TCI is the mean percentage of trap nights that possums were caught, corrected for sprung traps and nontarget captures, with trap line as the sampling unit. We studied I forest and I farmland area in the North Island, New Zealand, to address concerns that TCI estimates may not be readily comparable because of seasonal changes in the capture probability of possums. We located blocks of 6 trap lines at each area and randomly trapped I line in each block in 3 seasons (summer, winter, and spring) in 2000 and 2001. We developed a model to allow for variation in local population size and nightly capture probability, and fitted the model using the Bayesian analysis software BUGS. Capture probability declined with increasing abundance of possums, generating a nonlinear TCI. Capture probability in farmland was lower during spring relative to winter and summer, and to forest during summer. In the absence of a proven and cost-effective alternative, our results support the continued use of the TCI for monitoring the abundance of possums in New Zealand. Seasonal biases in the TCI should be minimized by conducting repeat sampling in the same season.

A comparison of solids collected in sediment traps and automated water samplers

USGS Publications Warehouse

Bartsch, L.A.; Rada, R.G.; Sullivan, J.F.

1996-01-01

Sediment traps are being used in some pollution monitoring programs in the USA to sample suspended solids for contaminant analyses. This monitoring approach assumes that the characteristics of solids obtained in sediment traps are the same as those collected in whole-water sampling devices. We tested this assumption in the upper Mississippi River, based on the inorganic particle-size distribution (determined with a laser particle- analyzer) and volatile matter content of solids (a surrogate for organic matter). Cylindrical sediment traps (aspect ratio 3) were attached to a rigid mooring device and deployed in a flowing side channel in Navigation Pool 7 of the upper Mississippi River. On each side of the mooring device, a trap was situated adjacent to a port of an autosampler that collected raw water samples hourly to form 2-d composite samples. Paired samples (one trap and one raw water, composite sample) were removed from each end of the mooring device at 2-d intervals during the 30-d study period and compared. The relative particle collection efficiency of paired samplers did not vary temporally. Particle-size distributions of inorganic solids from sediment traps and water samples were not significantly different. The volatile matter content of solids was lesser in sediment traps (mean, 9.5%) than in corresponding water samples (mean, 22.7%). This bias may have been partly due to under-collection of phytoplankton (mainly cyanobacteria), which were abundant in the water column during the study. The positioning of water samplers and sediment traps in the mooring device did not influence the particle-size distribution or total solids of samples. We observed a small difference in the amount of organic matter collected by water samplers situated at opposite ends of the mooring device.

INCREASING HEAVY OIL RESERVES IN THE WILMINGTON OIL FIELD THROUGH ADVANCED RESERVOIR CHARACTERIZATION AND THERMAL PRODUCTION TECHNOLOGIES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Unknown

2001-08-08

The objective of this project is to increase the recoverable heavy oil reserves within sections of the Wilmington Oil Field, near Long Beach, California, through the testing and application of advanced reservoir characterization and thermal production technologies. The hope is that successful application of these technologies will result in their implementation throughout the Wilmington Field and, through technology transfer, will be extended to increase the recoverable oil reserves in other slope and basin clastic (SBC) reservoirs. The existing steamflood in the Tar zone of Fault Block II-A (Tar II-A) has been relatively inefficient because of several producibility problems which aremore » common in SBC reservoirs: inadequate characterization of the heterogeneous turbidite sands, high permeability thief zones, low gravity oil and non-uniform distribution of the remaining oil. This has resulted in poor sweep efficiency, high steam-oil ratios, and early steam breakthrough. Operational problems related to steam breakthrough, high reservoir pressure, and unconsolidated sands have caused premature well and downhole equipment failures. In aggregate, these reservoir and operational constraints have resulted in increased operating costs and decreased recoverable reserves. A suite of advanced reservoir characterization and thermal production technologies are being applied during the project to improve oil recovery and reduce operating costs, including: (1) Development of three-dimensional (3-D) deterministic and stochastic reservoir simulation models--thermal or otherwise--to aid in reservoir management of the steamflood and post-steamflood phases and subsequent development work. (2) Development of computerized 3-D visualizations of the geologic and reservoir simulation models to aid reservoir surveillance and operations. (3) Perform detailed studies of the geochemical interactions between the steam and the formation rock and fluids. (4) Testing and proposed application of a novel alkaline-steam well completion technique for the containment of the unconsolidated formation sands and control of fluid entry and injection profiles. (5) Installation of a 2100 ft, 14 inch insulated, steam line beneath a harbor channel to supply steam to an island location. (6) Testing and proposed application of thermal recovery technologies to increase oil production and reserves: (a) Performing pilot tests of cyclic steam injection and production on new horizontal wells. (b) Performing pilot tests of hot water-alternating-steam (WAS) drive in the existing steam drive area to improve thermal efficiency. (7) Perform a pilot steamflood with the four horizontal injectors and producers using a pseudo steam-assisted gravity-drainage (SAGD) process. (8) Advanced reservoir management, through computer-aided access to production and geologic data to integrate reservoir characterization, engineering, monitoring and evaluation.« less

40 CFR 52.1923 - Best Available Retrofit Requirements (BART) for SO2 and Interstate pollutant transport provisions...

Code of Federal Regulations, 2014 CFR

2014-07-01

... combusted at any time at the steam generating unit. Daily average means the arithmetic average of the hourly... which may include, but is not limited to, monitoring results, review of operating and maintenance...

Monitoring the Status and Trends of Tropical Forest Terrestrial Vertebrate Communities from Camera Trap Data: A Tool for Conservation

PubMed Central

Ahumada, Jorge A.; Hurtado, Johanna; Lizcano, Diego

2013-01-01

Reducing the loss of biodiversity is key to ensure the future well being of the planet. Indicators to measure the state of biodiversity should come from primary data that are collected using consistent field methods across several sites, longitudinal, and derived using sound statistical methods that correct for observation/detection bias. In this paper we analyze camera trap data collected between 2008 and 2012 at a site in Costa Rica (Volcan Barva transect) as part of an ongoing tropical forest global monitoring network (Tropical Ecology Assessment and Monitoring Network). We estimated occupancy dynamics for 13 species of mammals, using a hierarchical modeling approach. We calculated detection-corrected species richness and the Wildlife Picture Index, a promising new indicator derived from camera trap data that measures changes in biodiversity from the occupancy estimates of individual species. Our results show that 3 out of 13 species showed significant declines in occupancy over 5 years (lowland paca, Central American agouti, nine-banded armadillo). We hypothesize that hunting, competition and/or increased predation for paca and agouti might explain these patterns. Species richness and the Wildlife Picture Index are relatively stable at the site, but small herbivores that are hunted showed a decline in diversity of about 25%. We demonstrate the usefulness of longitudinal camera trap deployments coupled with modern statistical methods and advocate for the use of this approach in monitoring and developing global and national indicators for biodiversity change. PMID:24023898

Sampling bees in tropical forests and agroecosystems: A review

USGS Publications Warehouse

Prado, Sara G.; Ngo, Hien T.; Florez, Jaime A.; Collazo, Jaime A.

2017-01-01

Bees are the predominant pollinating taxa, providing a critical ecosystem service upon which many angiosperms rely for successful reproduction. Available data suggests that bee populations worldwide are declining, but scarce data in tropical regions precludes assessing their status and distribution, impact on ecological services, and response to management actions. Herein, we reviewed >150 papers that used six common sampling methods (pan traps, baits, Malaise traps, sweep nets, timed observations and aspirators) to better understand their strengths and weaknesses, and help guide method selection to meet research objectives and development of multi-species monitoring approaches. Several studies evaluated the effectiveness of sweep nets, pan traps, and malaise traps, but only one evaluated timed observations, and none evaluated aspirators. Only five studies compared two or more of the remaining four sampling methods to each other. There was little consensus regarding which method would be most reliable for sampling multiple species. However, we recommend that if the objective of the study is to estimate abundance or species richness, malaise traps, pan traps and sweep nets are the most effective sampling protocols in open tropical systems; conversely, malaise traps, nets and baits may be the most effective in forests. Declining bee populations emphasize the critical need in method standardization and reporting precision. Moreover, we recommend reporting a catchability coefficient, a measure of the interaction between the resource (bee) abundance and catching effort. Melittologists could also consider existing methods, such as occupancy models, to quantify changes in distribution and abundance after modeling heterogeneity in trapping probability, and consider the possibility of developing monitoring frameworks that draw from multiple sources of data.

Does Passive Sampling Accurately Reflect the Bee (Apoidea: Anthophila) Communities Pollinating Apple and Sour Cherry Orchards?

PubMed

Gibbs, Jason; Joshi, Neelendra K; Wilson, Julianna K; Rothwell, Nikki L; Powers, Karen; Haas, Mike; Gut, Larry; Biddinger, David J; Isaacs, Rufus

2017-06-01

During bloom of spring orchard crops, bees are the primary providers of pollination service. Monitoring these insects for research projects is often done by timed observations or by direct aerial netting, but there has been increasing interest in blue vane traps as an efficient passive approach to collecting bees. Over multiple spring seasons in Michigan and Pennsylvania, orchards were monitored for wild bees using timed netting from crop flowers and blue vane traps. This revealed a distinctly different community of wild bees captured using the two methods, suggesting that blue vane traps can complement but cannot replace direct aerial netting. The bee community in blue vane traps was generally composed of nonpollinating species, which can be of interest for broader biodiversity studies. In particular, blue vane traps caught Eucera atriventris (Smith), Eucera hamata (Bradley), Bombus fervidus (F.), and Agapostemon virescens (F.) that were never collected from the orchard crop flowers during the study period. Captures of bee species in nets was generally stable across the 3 yr, whereas we observed significant declines in the abundance of Lasioglossum pilosum (Smith) and Eucera spp. trapped using blue vane traps during the project, suggesting local overtrapping of reproductive individuals. We conclude that blue vane traps are a useful tool for expanding insights into bee communities within orchard crop systems, but they should be used with great caution to avoid local extirpation of these important insects. © The Authors 2017. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

An expert system/ion trap mass spectrometry approach for life support systems monitoring

NASA Technical Reports Server (NTRS)

Palmer, Peter T.; Wong, Carla M.; Yost, Richard A.; Johnson, Jodie V.; Yates, Nathan A.; Story, Michael

1992-01-01

Efforts to develop sensor and control system technology to monitor air quality for life support have resulted in the development and preliminary testing of a concept based on expert systems and ion trap mass spectrometry (ITMS). An ITMS instrument provides the capability to identify and quantitate a large number of suspected contaminants at trace levels through the use of a variety of multidimensional experiments. An expert system provides specialized knowledge for control, analysis, and decision making. The system is intended for real-time, on-line, autonomous monitoring of air quality. The key characteristics of the system, performance data and analytical capabilities of the ITMS instrument, the design and operation of the expert system, and results from preliminary testing of the system for trace contaminant monitoring are described.

High pressure/high temperature thermogravimetric apparatus. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Calo, J.M.; Suuberg, E.M.

1999-12-01

The purpose of this instrumentation grant was to acquire a state-of-the-art, high pressure, high temperature thermogravimetric apparatus (HP/HT TGA) system for the study of the interactions between gases and carbonaceous solids for the purpose of solving problems related to coal utilization and applications of carbon materials. The instrument that we identified for this purpose was manufactured by DMT (Deutsche Montan Technologies)--Institute of Cokemaking and Coal Chemistry of Essen, Germany. Particular features of note include: Two reactors: a standard TGA reactor, capable of 1100 C at 100 bar; and a high temperature (HT) reactor, capable of operation at 1600 C andmore » 100 bar; A steam generator capable of generating steam to 100 bar; Flow controllers and gas mixing system for up to three reaction gases, plus a separate circuit for steam, and another for purge gas; and An automated software system for data acquisition and control. The HP/TP DMT-TGA apparatus was purchased in 1996 and installed and commissioned during the summer of 1996. The apparatus was located in Room 128 of the Prince Engineering Building at Brown University. A hydrogen alarm and vent system were added for safety considerations. The system has been interfaced to an Ametek quadruple mass spectrometer (MA 100), pumped by a Varian V250 turbomolecular pump, as provided for in the original proposed. With this capability, a number of gas phase species of interest can be monitored in a near-simultaneous fashion. The MS can be used in a few different modes. During high pressure, steady-state gasification experiments, it is used to sample, measure, and monitor the reactant/product gases. It can also be used to monitor gas phase species during nonisothermal temperature programmed reaction (TPR) or temperature programmed desorption (TPD) experiments.« less

Abundance and species richness of snakes along the Middle Rio Grande riparian forest in New Mexico

Treesearch

Heather L. Bateman; Alice Chung-MacCoubrey; Howard L. Snell; Deborah M. Finch

2009-01-01

To understand the effects of removal of non-native plants and fuels on wildlife in the riparian forest of the Middle Rio Grande in New Mexico, we monitored snakes from 2000 to 2006 using trap arrays of drift fences, pitfalls, and funnel traps. We recorded 158 captures of 13 species of snakes from 12 study sites. We captured more snakes in funnel traps than in pitfalls...

Test of nonhost angiosperm volatiles and verbenone to protect trap trees for Sirex noctilio (Hymenoptera: Siricidae) from attacks by bark beetles (Coleoptera: Scolytidae) in the Northeastern United States

Treesearch

Kevin Dodds; Daniel Miller

2010-01-01

Sirex noctilio F. (Hymenoptera: Siricidae) is an invasive woodwasp, currently established in northeastern North America. In other regions of the world, stressed trap trees are used to monitor populations of S. noctilio and to provide inoculation points for the biological control nematode Deladenus siricidicola Bedding. However, the operational use of trap trees for S....

Evaluation of rapid readout biological indicators for 132 degrees C gravity and 132 degrees C vacuum-assisted steam sterilization cycles using a new automated fluorescent reader.

PubMed

Alfa, Michelle J; Olson, Nancy; DeGagne, Pat; Jackson, Michele

2002-07-01

The primary objective of this study was to evaluate fluorescent readout results of Attest 1291 Biological Indicators (BIs) (3M Health Care, St. Paul, MN) and Attest 1296 BI test packs (containing Attest 1292 BIs) using full and fractional cycles compared with the growth data when prolonged incubation (7 days) was included. Gravity displacement and vacuum-assisted steam sterilization cycles were evaluated. A secondary objective of this study was to evaluate the new automated rapid fluorescent reader (Attest 290 Auto Reader). The rapid readout BIs for gravity displacement and vacuum-assisted steam autoclave cycles at 132 degrees C were processed using full (4 minutes) and four fractional cycles that provided 30% to 80% positive results for growth after 24 hours of incubation (48 hours of incubation for Attest 1292 BIs from the Attest 1296 test packs). Sixty of each type of BI were tested for each cycle (300 of each BI type in total). For all full steam sterilization cycles, results of the rapid fluorescent readout and the 24-hour, 48-hour, and 7-day growth tests were negative for all Attest 1291 and 1292 BIs tested. For all fractional cycles, the 24- and 48-hour growth results for the Attest 1291 and 1292 BIs, respectively, were the same as the 7-day growth results. The fractional cycle data indicated that fluorescent rapid readout was a more sensitive indicator than growth. There were rare (0.9%) false-negative results for BIs under fractional cycle conditions and these all correlated with short fractional cycle exposure times. The fluorescent rapid readout results of the 1291 BIs and 1296 BI test packs reliably predict both 24- and 48-hour and 7-day growth. These data support the value of rapid readout BIs for sterilizer monitoring for both the vacuum-assisted and the gravity displacement steam sterilization cycles. The new automated reader requires less manipulation of the BI and makes monitoring user friendly and less prone to user errors.

Hydrologic and geochemical monitoring in Long Valley Caldera, Mono County, California, 1985

USGS Publications Warehouse

Farrar, C.D.; Sorey, M.L.; Rojstaczer, S.A.; Janik, C.J.; Winnett, T.L.; Clark, M.D.

1987-01-01

Hydrologic and geochemical monitoring, to detect changes caused by magmatic and tectonic processes in the Long Valley caldera has continued through 1985. The monitoring included the collection of the following types of data: chemical and isotopic composition of water and gases from springs, wells, and steam vents; temperatures in wells, springs, and steam vents; flow rates of springs and streams; water levels in wells; and barometric pressure and precipitation at several sites. In addition, reservoir temperatures for the geothermal system were estimated from computations based on chemical geothermometers applied to fluid samples from wells and springs. Estimates of thermal water discharged from springs were made on the basis of boron and chloride fluxes in surface waters for selected sites in the Casa Diablo area and along the Mammoth-Hot Creek drainage. These data are presented in tables and graphs. The Long Valley area was relatively quiescent throughout 1985 in terms of geodetic changes and seismic activity. As a consequence , the hydrologic system varied mainly in response to seasonal influences of temperature, atmospheric pressure, and precipitation. However, spring flows near Casa Diablo were influenced by pumping at the geothermal production well field nearby. (Author 's abstract)

Advanced Signal Processing for High Temperatures Health Monitoring of Condensed Water Height in Steam Pipes

NASA Technical Reports Server (NTRS)

Lih, Shyh-Shiuh; Bar-Cohen, Yoseph; Lee, Hyeong Jae; Takano, Nobuyuki; Bao, Xiaoqi

2013-01-01

An advanced signal processing methodology is being developed to monitor the height of condensed water thru the wall of a steel pipe while operating at temperatures as high as 250deg. Using existing techniques, previous study indicated that, when the water height is low or there is disturbance in the environment, the predicted water height may not be accurate. In recent years, the use of the autocorrelation and envelope techniques in the signal processing has been demonstrated to be a very useful tool for practical applications. In this paper, various signal processing techniques including the auto correlation, Hilbert transform, and the Shannon Energy Envelope methods were studied and implemented to determine the water height in the steam pipe. The results have shown that the developed method provides a good capability for monitoring the height in the regular conditions. An alternative solution for shallow water or no water conditions based on a developed hybrid method based on Hilbert transform (HT) with a high pass filter and using the optimized windowing technique is suggested. Further development of the reported methods would provide a powerful tool for the identification of the disturbances of water height inside the pipe.

Quantification of the effect of terrace maintenance on soil erosion: two seasons of monitoring experiments in Cyprus

NASA Astrophysics Data System (ADS)

Camera, Corrado; Djuma, Hakan; Zoumides, Christos; Eliades, Marinos; Charalambous, Katerina; Bruggeman, Adriana

2017-04-01

In the Mediterranean region, rural communities in topographically challenging sites have converted large areas into dry-stone terraces, as the only way to develop sustainable agriculture. Terraces allow softening the steep mountainous slopes, favoring water infiltration and reducing water runoff and soil erosion. However, population decrease over the past 30 years has led to a lack of maintenance of the terraces and the onset of a process of land degradation. The objective of this study is the quantification of the effect of terrace maintenance on soil erosion. We selected two terraces - A and B, 11 and 14 m long, respectively - for monitoring purposes. They are located in a small catchment (10,000 m2) in the Troodos Mountains of Cyprus, at an elevation of 1,300 m a.s.l., and cultivated with vineyards, which is the main agricultural land use of the region. We monitored soil erosion by means of sediment traps, which are installed along 1-m long sections of terrace. We monitored four sections on terrace A and seven on terrace B. During the first monitoring season (winter 2015/16), on terrace A the traps caught sediment of two collapsed and two standing sections of dry-stone wall. The catchment areas of one set of traps (degraded and non-degraded) were closed by a 1x4-m2 plot, to relate erosion rates to a known draining area. On terrace B the traps were all open and caught four collapsed and three standing sections. Also, we installed a weather station (5-minute rainfall, temperature, and relative humidity) and 15 soil moisture sensors, to relate soil erosion processes with climate and (sub)surface hydrology. From the open traps, we observed that soil loss is on average 8 times higher from degraded terrace sections than from standing, well maintained sections, which in our case study corresponds to an 87% reduction of soil loss due to terrace maintenance. If we compare data from the two closed plots, we obtain a much higher soil loss ratio (degraded/standing) of 56, which corresponds to a soil loss reduction of 98%. From the closed plots, we derived an erosion rate of 2.8 t ha-1 y-1 for degraded terraces and 0.05 t ha-1 y-1 for well-maintained terraces. Also, soil moisture monitoring confirmed that standing terraces favor surface water infiltration. For the second season (winter 2016/17), given the differences in results between open and closed traps and therefore the difficulty in consistently upscaling the results, we modified the monitoring design. The 11 traps were kept, all open, but the comparison between maintained and degraded areas is carried out on a sub-catchment basis, rather than on a section basis. We restored the whole sub-catchment of terrace A (≈480-m2) to be considered the maintained treatment of our experiment and kept the sub-catchment of terrace B (≈600-m2) in degraded conditions. To obtain the sub-catchment erosion rate, the sediment collected in the traps is averaged on running meter of wall and integrated on the wall length. This research is supported by the European Union's FP7 RECARE Project (GA 603498).

Seasonal dynamics of three insect pests in the cabbage field in central Slovenia.

PubMed

Trdan, Stanislav; Vidrih, Matej; Bobnar, Aleksander

2008-01-01

From the beginning of April until the beginning of November 2006, a seasonal dynamics of three harmful insect species--Swede midge (Contarinia nasturtii [Kieffer], Diptera, Cecidomyiidae), flea beetles (Phyllotreta spp., Coleoptera, Chrysomelidae), and diamondback moth (Plutella xylostella [L.], Lepidoptera, Plutellidae)--was investigated at the Laboratory Field of the Biotechnical Faculty in Ljubljana (Slovenia). The males were monitored with pheromone traps; the males of Swede midge were trapped with the traps of Swiss producer (Agroscope FAW, Wädenswill), while the adult flea beetles (trap type KLP+) and diamondback moths (trap type RAG) were trapped with the Hungarian traps (Plant Protection Institute, Hungarian Academy of Sciences). The pheromone capsules were changed in 4-week intervals, while the males were counted on about every 7th day. The first massive occurrence of diamondback moth (1.6 males/trap/day) was established in the second 10 days period of April, and the pest remained active until the 2nd 10 days period of September. The adults were the most numerous in the period between the end of May until the middle of June, but even then their number did not exceed three males caught per day. In the first 10 days period of May, the first adult flea beetles were recorded in the pheromone traps, while their notable number (0.8 males/trap/day) was stated in the third 10 days period of May. Absolutely the highest number of the beetles was recorded in the second (19 adults/trap/day) and in the third (25 adults/trap/day) 10 days of July, and the pest occurred until the beginning of October. The first massive occurrence of Swede midge (0.4 males/trap/day) was established in the second 10 days period of May, while the highest number of males (8/trap/day) were caught in the second 10 days period of July. In the third 10 days period of October, the last adults were found in the traps. Based on the results of monitoring of three cabbage insect pests we ascertained that in the central Slovenia the Swede midge has 3-4 generations, the flea beetles has 1-2 generations, and the diamondback moth has 4 generations.

Trappers set up trap for lizard

NASA Technical Reports Server (NTRS)

2000-01-01

In hope of catching a large monitor lizard seen in the area, state-licensed animal trappers Dewey Kessler and James Dean (at left), with Gary Povitch (kneeling) of the U.S. Wildlife and Dan Turner (standing) set up a trap on KSC. The lizard has been spotted recently near S.R. 3, a route into the Center, by several area residents. Turner is a monitor expert. The lizard is not a native of the area, and possibly a released pet. Dean is working with the cooperation of KSC and the Merritt Island National Wildlife Refuge.

A New Visual Trap for Rhagoletis cerasi (L.) (Diptera: Tephritidae)

PubMed Central

Daniel, Claudia; Mathis, Samuel; Feichtinger, Georg

2014-01-01

The European cherry fruit fly, Rhagoletis cerasi (L.) (Diptera: Tephritidae), is the most important pest of sweet cherries in Europe. The aim of our experiments was to develop a new, cost-efficient, lead chromate-free and more eco-friendly trap for monitoring and mass trapping of R. cerasi. Five different-colored yellow panels and three different trap shapes were compared to a standard Rebell® amarillo trap in three experimental orchards in 2012. Trap color F, with a strong increase in reflectance at 500–550 nm and a secondary peak in the UV-region at 300–400 nm, captured significantly more flies than the standard Rebell® amarillo trap. Yellow traps with increased reflectance in the blue region (400–500 nm) were least attractive. Trap shape was of minor importance, as long as the object was three-dimensional and visible from all directions. Based on economic and practical considerations, a cylinder-shaped trap “UFA-Samen Kirschenfliegenfalle” was developed for commercial use and is currently under on-farm evaluation. PMID:26462825

Camera traps can be heard and seen by animals.

PubMed

Meek, Paul D; Ballard, Guy-Anthony; Fleming, Peter J S; Schaefer, Michael; Williams, Warwick; Falzon, Greg

2014-01-01

Camera traps are electrical instruments that emit sounds and light. In recent decades they have become a tool of choice in wildlife research and monitoring. The variability between camera trap models and the methods used are considerable, and little is known about how animals respond to camera trap emissions. It has been reported that some animals show a response to camera traps, and in research this is often undesirable so it is important to understand why the animals are disturbed. We conducted laboratory based investigations to test the audio and infrared optical outputs of 12 camera trap models. Camera traps were measured for audio outputs in an anechoic chamber; we also measured ultrasonic (n = 5) and infrared illumination outputs (n = 7) of a subset of the camera trap models. We then compared the perceptive hearing range (n = 21) and assessed the vision ranges (n = 3) of mammals species (where data existed) to determine if animals can see and hear camera traps. We report that camera traps produce sounds that are well within the perceptive range of most mammals' hearing and produce illumination that can be seen by many species.

[Affecting factors on capture efficacy of sex pheromone traps for Cydia pomonella L].

PubMed

Zhai, Xiao-Wei; Liu, Wan-Xue; Zhang, Gui-Fen; Wan, Fang-Hao; Xu, Hong-Fu; Pu, Chong-Jian

2010-03-01

Codling moth Cydia pomonella L. (Lepidoptera, Olethreutidae) is the most serious pest of orchards, and one of the most important quarantine pests in China. This paper studied the effects of the color, shape, placement location, lure color, and lure number of sex pheromone traps on the capture efficacy for C. pomonella L. male moth. It was found that the capture efficacy of white and green traps was two times higher than that of blue trap (P < 0.05), and water bottle and triangle traps had no significant difference in their trapping effect. The traps hung in the middle of crown gave two times higher catches than those hung in the upper portion of crown (P < 0.05). Lure color and number had no significant effect on the capture efficacy. The present results could be used in better monitoring C. pomonella by using its sex pheromones.

SURVEY ON PREVACUUM HIGH-PRESSURE STEAM STERILIZERS.

PubMed

DARMADY, E M; DREWETT, S E; HUGHES, K E

1964-03-01

None of the 10 prevacuum high-pressure sterilizers of different makes tested was able to produce and maintain the conditions advocated by the Medical Research Council working party on high-pressure steam sterilizers (1959) or by Knox and Penikett (1958) with the result that steam did not penetrate adequately the single challenge load and it was not sterilized. The sterilization of ;group drums' of various sizes and contents was erratic and tended to give operators a false sense of security. An alarming number of minor engineering faults were present in seven out of 10 machines tested and they require very much more skilled maintenance than is being given at the moment. The possibility of centralizing sterilizers to central sterile supply departments and placing them under the care of a regional engineer cannot be too highly recommended. The presence of undetected ;leaks' and a failure to draw a prevacuum of 20 mm. even with a steam burst interferes with sterilization of a challenge load. A leak test should be performed twice daily and should not exceed more than 1 mm. in one minute at 20 mm. absolute. The centre of the load should be monitored by crossed tapes or Brownes tubes in each sterilizing cycle. Although the challenge load was sterilized when the chamber was filled to capacity, a more reliable cycle consisting of a double prevacuum of 20 mm. or more with intermediate steam burst to 10 lb. ensured the sterilizing of a single challenge load, which could be adequately controlled by the chamber drain temperature.

Sample environment for in situ synchrotron corrosion studies of materials in extreme environments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Elbakhshwan, Mohamed S.; Gill, Simerjeet K.; Motta, Arthur T.

A new in situ sample environment has been designed and developed to study the interfacial interactions of nuclear cladding alloys with high temperature steam. The sample environment is particularly optimized for synchrotron X-ray diffraction (XRD) studies for in situ structural analysis. The sample environment is highly corrosion resistant and can be readily adapted for steam environments. The in situ sample environment design complies with G2 ASTM standards for studying corrosion in zirconium and its alloys and offers remote temperature and pressure monitoring during the in situ data collection. The use of the in situ sample environment is exemplified by monitoringmore » the oxidation of metallic zirconium during exposure to steam at 350°C. Finally, the in situ sample environment provides a powerful tool for fundamental understanding of corrosion mechanisms by elucidating the substoichiometric oxide phases formed during early stages of corrosion, which can provide a better understanding the oxidation process.« less

Sample environment for in situ synchrotron corrosion studies of materials in extreme environments

DOE PAGES

Elbakhshwan, Mohamed S.; Gill, Simerjeet K.; Motta, Arthur T.; ...

2016-10-25

A new in situ sample environment has been designed and developed to study the interfacial interactions of nuclear cladding alloys with high temperature steam. The sample environment is particularly optimized for synchrotron X-ray diffraction (XRD) studies for in situ structural analysis. The sample environment is highly corrosion resistant and can be readily adapted for steam environments. The in situ sample environment design complies with G2 ASTM standards for studying corrosion in zirconium and its alloys and offers remote temperature and pressure monitoring during the in situ data collection. The use of the in situ sample environment is exemplified by monitoringmore » the oxidation of metallic zirconium during exposure to steam at 350°C. Finally, the in situ sample environment provides a powerful tool for fundamental understanding of corrosion mechanisms by elucidating the substoichiometric oxide phases formed during early stages of corrosion, which can provide a better understanding the oxidation process.« less

Building double-decker traps for early detection of emerald ash borer

Treesearch

Deborah G. McCullough; Therese M. Poland

2017-01-01

Emerald ash borer (EAB) (Agrilus planipennis Fairmaire), the most destructive forest insect to have invaded North America, has killed hundreds of millions of forest and landscape ash (Fraxinus spp.) trees. Several artificial trap designs to attract and capture EAB beetles have been developed to detect, delineate, and monitor...

Captures of boll weevils (Coleoptera: Curculionidae) in relation to trap distance from cotton fields

USDA-ARS?s Scientific Manuscript database

Once populations of the boll weevil (Anthonomus grandis grandis Boheman) are suppressed, eradication programs rely on pheromone trap-based monitoring for timely detection of weevil populations in cotton (Gossypium spp.). Delayed detection may increase the costs of remedial treatments, and permit rep...

Experiments With Trapped Neutral Atoms

DTIC Science & Technology

2010-01-05

number of condensate atoms in the trap [11]. (a) i solitons (b) £ 10 \\QT>J — \\^y Darks -WW . ’ VrV Ground state A(|>=0 <* -^ Mr...interacting condensates leading to soliton formation for a relative phase of Pi. (b) The relative phase of two split condensates was monitored for various

Diaphorina citri (Hemiptera:Liviidae) abundance in Puerto Rico declines with elevation

USDA-ARS?s Scientific Manuscript database

Diaphorina citri is the primary vector of Hunglongbing disease, the most devastating disease of citrus. Diaphorina citri populations in Puerto Rico were monitored with yellow sticky traps on citrus trees at different elevations, ranging from 10 to 880 m above sea level. Trapping was conducted in Mar...

Haematophageous vector monitoring in Djibouti city from 2008 to 2009: first records of Culex pipiens ssp. torridus (IGLISCH), and Anopheles sergentii (theobald).

PubMed

Faulde, Michael K; Ahmed, Ammar A

2010-08-01

The Horn of Africa represents a region formerly known to be highly susceptible to mosquito-borne infectious diseases. In order to monitor and analyze the current presence and threat of vector mosquitoes, continuous and standardized trapping using CDC light traps without an additional CO2-generator has been carried out at six selected monitoring sites located in Djibouti City, from August 2008 until December 2009. An overall of 620 haematophageous Diptera were trapped, 603 (97.3%) were mosquitoes, 10 (1.6%) were sand flies, and 7 (1.1%) were biting midges, respectively. Genus distribution of mosquitoes revealed that 600 (99.5%) were Culex spp., 2 (0.3%) were Anopheles sergentii, and 1 (0.2%) was Aedes aegypti. Culex species were represented by Cx. quinquefasciatus (78.5%), and Cx. pipiens ssp. torridus (21.5%). The later species was first detected focally in early December 2009 showing a strongly increasing population density resulting in a maximum trap rate of 25 mosquitoes per trap night. Sand flies were all Sergentomyia antennata, and biting midges of the genus Culicoides were represented by C. nubeculosus (71.4%) and C. vexans (28.6 %). The findings included the first records for Cx. pipiens ssp. torridus and An. sergentii in Djibouti. However, none of the captured female Culex spp, the known vector for West Nile Virus, showed positive results for viral nucleic acids using WNV RT-real time PCR system. Also, females An. sergentii were Plasmodium falciparum and P. vivax circumsporozoite protein negative.

40 CFR 69.12 - Continuing exemptions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... “the Act”, the Administrator of the Environmental Protection Agency (EPA) exempts the Guam Power Authority's two sixty-six megawatt oil-fired steam units which comprise the Cabras Power Plant from sulfur... limited to strict implementation of both the monitoring (wind direction and ambient SO2 concentration) and...

40 CFR 69.12 - Continuing exemptions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... “the Act”, the Administrator of the Environmental Protection Agency (EPA) exempts the Guam Power Authority's two sixty-six megawatt oil-fired steam units which comprise the Cabras Power Plant from sulfur... limited to strict implementation of both the monitoring (wind direction and ambient SO2 concentration) and...

Nanophotonic Trapping for Precise Manipulation of Biomolecular Arrays

PubMed Central

Soltani, Mohammad; Lin, Jun; Forties, Robert A.; Inman, James T.; Saraf, Summer N.; Fulbright, Robert M.; Lipson, Michal; Wang, Michelle D.

2014-01-01

Optical trapping is a powerful manipulation and measurement technique widely employed in the biological and materials sciences1–8. Miniaturizing optical trap instruments onto optofluidic platforms holds promise for high throughput lab-on-chip applications9–16. However, a persistent challenge with existing optofluidic devices has been controlled and precise manipulation of trapped particles. Here we report a new class of on-chip optical trapping devices. Using photonic interference functionalities, an array of stable, three-dimensional on-chip optical traps is formed at the antinodes of a standing-wave evanescent field on a nanophotonic waveguide. By employing the thermo-optic effect via integrated electric microheaters, the traps can be repositioned at high speed (~ 30 kHz) with nanometer precision. We demonstrate sorting and manipulation of individual DNA molecules. In conjunction with laminar flows and fluorescence, we also show precise control of the chemical environment of a sample with simultaneous monitoring. Such a controllable trapping device has the potential for high-throughput precision measurements on chip. PMID:24776649

Nanophotonic trapping for precise manipulation of biomolecular arrays.

PubMed

Soltani, Mohammad; Lin, Jun; Forties, Robert A; Inman, James T; Saraf, Summer N; Fulbright, Robert M; Lipson, Michal; Wang, Michelle D

2014-06-01

Optical trapping is a powerful manipulation and measurement technique widely used in the biological and materials sciences. Miniaturizing optical trap instruments onto optofluidic platforms holds promise for high-throughput lab-on-a-chip applications. However, a persistent challenge with existing optofluidic devices has been achieving controlled and precise manipulation of trapped particles. Here, we report a new class of on-chip optical trapping devices. Using photonic interference functionalities, an array of stable, three-dimensional on-chip optical traps is formed at the antinodes of a standing-wave evanescent field on a nanophotonic waveguide. By employing the thermo-optic effect via integrated electric microheaters, the traps can be repositioned at high speed (∼30 kHz) with nanometre precision. We demonstrate sorting and manipulation of individual DNA molecules. In conjunction with laminar flows and fluorescence, we also show precise control of the chemical environment of a sample with simultaneous monitoring. Such a controllable trapping device has the potential to achieve high-throughput precision measurements on chip.

Developing an ecosystem perspective from experimental monitoring programs: I. Demographic responses of a rare geothermal grass to soil temperature.

PubMed

Pavlik, B M; Enberg, A

2001-08-01

The geysers panic grass [Dichanthelium lanuginosum Spellenberg var. thermale (Bol.) Spellenberg or DILA] is exclusively associated with surface geothermal manifestations in Sonoma County, California, USA (38 degrees 46'N, 122 degrees 38'W). Steam extraction by power plants could alter the subsurface distribution of heat and water to the site, potentially impacting subpopulations of this rare plant. The purpose of this study was to use demographic monitoring to determine: (1) temporal and spatial patterns of soil temperature in relation to the distribution of established DILA individuals at Little Geysers, (2) in situ response of experimental populations of DILA to spatial variations in soil temperature, and (3) habitat requirements of DILA as an indicator of its tolerance to variations in surficial geothermal features. Thermocouple transects and a datalogger provided data for characterizing the spatial and temporal patterns of soil temperature in four microhabitats (fumarole, DILA stand, Andropogon stand, and cleared). Experimental populations were established by precisely sowing and monitoring DILA seeds in these microhabitats. The results indicated that spatial and temporal variations in soil temperature had significant effects on the processes of germination, growth, survivorship, and reproduction, thus producing a readily observed metapopulation patch dynamic in relation to geothermal activity. Seasonal depressions of soil temperature near the fumaroles by cold air and prolonged rainfall events also promoted the emergence and survival of DILA seedlings in a microhabitat that was previously too hot to occupy. Over longer periods of time, DILA metapopulation dynamism reflected climatic and geothermal variation. Drought years inhibited germination for lack of water, but more importantly for the lack of requisite soil temperature depressions in the fumarole microhabitat. Wet years promoted subpopulation expansion into transition areas that were once too hot and dry. There have also been shifts in the underground distribution of steam into areas distant from known geothermal features. The demographic responses of DILA to spatial and temporal variations in soil temperature indicate that heat is an absolutely essential component of the steam resource. In its absence, germination, seeding survivorship, growth, and maturation are significantly inhibited even if soil conditions are favorable and potential competitors are controlled. Ultimately, persistence of the species depends on maintaining the ecosystem dynamic of colonization and extirpation in response to variations in surficial geothermal features over long spatial and temporal scales. This should shift management perspective from its narrow focus on individual plants to a wider focus on monitoring the essential habitat component of steam.

Benzalkonium Chloride Provides Remarkable Stability to Liquid Protein Lures for Trapping Anastrepha obliqua (Diptera: Tephritidae).

PubMed

Lasa, R; Williams, T

2017-12-05

Hydrolyzed protein lures are widely used to monitor fruit fly pests but are rapidly degraded by microbial activity and must be replaced frequently. To improve the stability of lures, the quaternary ammonium biocide, benzalkonium chloride (BC), was evaluated in mixtures with two hydrolyzed proteins commonly used to monitor Anastrepha spp. The mean number of Anastrepha obliqua adults captured during six consecutive weeks using Captor + borax with the addition of 240 mg BC/liter, not renewed during the test, was similar to Captor + borax that was replaced at weekly intervals and was more effective than Captor + borax without BC. Numbers of A. obliqua flies captured in 30% CeraTrap diluted in water containing 240 mg BC/liter were similar to those caught in traps baited with Captor + borax or 30% CeraTrap without BC in the first 9 d of evaluation but was significantly more effective than both lures after 56 d. After >2 mo of use, 30% CeraTrap containing 240 mg BC/liter remained as effective as newly prepared 30% CeraTrap. The addition of BC to lures reduced surface tension of liquid lures by ~40-50%. However, when BC was increased to 720 mg BC/liter, only a small additional reduction in surface tension was observed and higher concentrations of BC did not increase capture rates. These findings could contribute to reduced costs for trapping networks and the development of long-lasting formulations of liquid protein lures for bait stations and mass-trapping targeted at major tephritid pests. © The Author(s) 2017. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Trap-effectiveness and response to tiletamine-zolazepam and medetomidine anaesthesia in Eurasian wild boar captured with cage and corral traps

PubMed Central

2013-01-01

Background Capture, handling and chemical restraint are basic techniques often needed for research or management purposes. The aim of this study was testing a combination of tiletamine-zolazepam (TZ) (3 mg/kg) and medetomidine (M) (0.05 mg/kg) on Eurasian wild boar (Sus scrofa). A total of 77 free-ranging wild boar were captured by means of portable cages and corral traps and then anaesthetized with intramuscular darts using a blowpipe. The individual response to chemical immobilization was characterized using anaesthetic, clinical, and serum biochemical variables. After the procedure, 14 of these wild boar were monitored for 20 days using GPS-GSM collars. Results Pre-release mortality during capture and handling (6.5%) was associated with severe trauma in corral traps. Capture specificity for wild boar was 96.3% and trapping effort was 16.5 days per captured wild boar. Mean induction period was 4.5 ± 2.2 min, hypnosis period enabling effective handling was 61.6 ± 25.4 min, and recovery period was 12.8 ± 12.1 min. No heart or respiratory failure due to added stress occurred and post-release monitoring by GPS-devices revealed no mortality due to anaesthesia. According to the best statistical model obtained, the main factor driving anaesthetic efficacy and stress indicators is trap type. Conclusions Both cage and corral traps are efficient methods to capture wild boar. Cage traps are safer, as demonstrated by mortality rates as well as anaesthetic, physiological, and serum biochemical responses. This anaesthetic protocol is useful for prolonged handling of wild boar and allows sampling and collecting data for ecological and epidemiological studies. PMID:23702232

Sticky Traps Baited with Synthetic Aggregation Pheromone Predict Fruit Orchard Infestations of Plautia stali (Hemiptera: Pentatomidae).

PubMed

Toyama, Masatoshi; Kishimoto, Hidenari; Mishiro, Koji; Nakano, Ryo; Ihara, Fumio

2015-10-01

The brown-winged green bug, Plautia stali Scott, mainly reproduces on Japanese cedar or cypress cones in Japanese plantation forests during summer and autumn. It often depletes its food sources in forest habitats and moves to cultivated crops in large numbers. To establish an easy method for assessing the risk of fruit orchard infestation by P. stali, we conducted a 3-yr field survey that monitored the attraction of bugs to the synthetic P. stali aggregation pheromone using a sticky trap. We used a morphological indicator, variable body size depending on food intake, to estimate the nutritional status in nymphs, which showed that nymphs attracted to the synthetic pheromone were starving. Comparisons between increasing changes in the number of stylet sheaths left on the cones by P. stali and the number of trapped nymphs show that monitoring nymphs with the pheromone-baited sticky trap is useful for inferring conditions regarding food resources in forest habitats. The trend toward trapping second instars can provide a timely overview of resource competition for cones. Trapping middle-to-late (third-fifth) instars is a warning that the cones are finally depleted and that there is a high probability that adults will leave the forests and invade the orchards. In addition, trends in trapping adults suggest that there is a potential risk of orchard infestation by the pest and predict the intensity and period of the invasion. The pheromone-baited sticky trap is an easy but useful survey tool for predicting P. stali orchard infestations. © The Authors 2015. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Integrated Status and Effectiveness Monitoring Program; Expansion of Existing Smolt Trapping Program in Nason Creek, 2005 Annual Report.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prevatte, Scott A.

2006-03-01

In the fall of 2004, as one part of a Basin-Wide Monitoring Program developed by the Upper Columbia Regional Technical Team and Upper Columbia Salmon Recovery Board, the Yakama Nation Fisheries Resource Management program began monitoring downstream migration of ESA listed Upper Columbia River spring chinook salmon and Upper Columbia River steelhead in Nason Creek, a tributary to the Wenatchee River. This report summarizes juvenile spring chinook salmon and steelhead trout migration data collected in Nason Creek during 2005 and also incorporates data from 2004. We used species enumeration at the trap and efficiency trials to describe emigration timing andmore » to estimate population size. Data collection was divided into spring/early summer and fall periods with a break during the summer months occurring due to low stream flow. Trapping began on March 1st and was suspended on July 29th when stream flow dropped below the minimum (30 cfs) required to rotate the trap cone. The fall period began on September 28th with increased stream flow and ended on November 23rd when snow and ice began to accumulate on the trap. During the spring and early summer we collected 311 yearling (2003 brood) spring chinook salmon, 86 wild steelhead smolts and 453 steelhead parr. Spring chinook (2004 brood) outgrew the fry stage of fork length < 60 mm during June and July, 224 were collected at the trap. Mark-recapture trap efficiency trials were performed over a range of stream discharge stages whenever ample numbers of fish were being collected. A total of 247 spring chinook yearlings, 54 steelhead smolts, and 178 steelhead parr were used during efficiency trials. A statically significant relationship between stream discharge and trap efficiency has not been identified in Nason Creek, therefore a pooled trap efficiency was used to estimate the population size of both spring chinook (14.98%) and steelhead smolts (12.96%). We estimate that 2,076 ({+-} 119 95%CI) yearling spring chinook and 688 ({+-} 140 95%CI) steelhead smolts emigrated past the trap during the spring/early summer sample period along with 10,721 ({+-} 1,220 95%CI) steelhead parr. During the fall we collected 924 subyearling (2004 brood) spring chinook salmon and 1,008 steelhead parr of various size and age classes. A total of 732 spring chinook subyearlings and 602 steelhead parr were used during 13 mark-recapture trap efficiency trials. A pooled trap efficiency of 24.59% was used to calculate the emigration of spring chinook and 17.11% was used for steelhead parr during the period from September 28th through November 23rd. We estimate that 3758 ({+-} 92 95%CI) subyearling spring chinook and 5,666 ({+-} 414 95%CI) steelhead parr migrated downstream past the trap along with 516 ({+-} 42 95%CI) larger steelhead pre-smolts during the 2005 fall sample period.« less

Validation of the Hirst-Type Spore Trap for Simultaneous Monitoring of Prokaryotic and Eukaryotic Biodiversities in Urban Air Samples by Next-Generation Sequencing.

PubMed

Núñez, Andrés; Amo de Paz, Guillermo; Ferencova, Zuzana; Rastrojo, Alberto; Guantes, Raúl; García, Ana M; Alcamí, Antonio; Gutiérrez-Bustillo, A Montserrat; Moreno, Diego A

2017-07-01

Pollen, fungi, and bacteria are the main microscopic biological entities present in outdoor air, causing allergy symptoms and disease transmission and having a significant role in atmosphere dynamics. Despite their relevance, a method for monitoring simultaneously these biological particles in metropolitan environments has not yet been developed. Here, we assessed the use of the Hirst-type spore trap to characterize the global airborne biota by high-throughput DNA sequencing, selecting regions of the 16S rRNA gene and internal transcribed spacer for the taxonomic assignment. We showed that aerobiological communities are well represented by this approach. The operational taxonomic units (OTUs) of two traps working synchronically compiled >87% of the total relative abundance for bacterial diversity collected in each sampler, >89% for fungi, and >97% for pollen. We found a good correspondence between traditional characterization by microscopy and genetic identification, obtaining more-accurate taxonomic assignments and detecting a greater diversity using the latter. We also demonstrated that DNA sequencing accurately detects differences in biodiversity between samples. We concluded that high-throughput DNA sequencing applied to aerobiological samples obtained with Hirst spore traps provides reliable results and can be easily implemented for monitoring prokaryotic and eukaryotic entities present in the air of urban areas. IMPORTANCE Detection, monitoring, and characterization of the wide diversity of biological entities present in the air are difficult tasks that require time and expertise in different disciplines. We have evaluated the use of the Hirst spore trap (an instrument broadly employed in aerobiological studies) to detect and identify these organisms by DNA-based analyses. Our results showed a consistent collection of DNA and a good concordance with traditional methods for identification, suggesting that these devices can be used as a tool for continuous monitoring of the airborne biodiversity, improving taxonomic resolution and characterization together. They are also suitable for acquiring novel DNA amplicon-based information in order to gain a better understanding of the biological particles present in a scarcely known environment such as the air. Copyright © 2017 American Society for Microbiology.

Validation of the Hirst-Type Spore Trap for Simultaneous Monitoring of Prokaryotic and Eukaryotic Biodiversities in Urban Air Samples by Next-Generation Sequencing

PubMed Central

Núñez, Andrés; Amo de Paz, Guillermo; Ferencova, Zuzana; Rastrojo, Alberto; Guantes, Raúl; García, Ana M.; Alcamí, Antonio; Gutiérrez-Bustillo, A. Montserrat

2017-01-01

ABSTRACT Pollen, fungi, and bacteria are the main microscopic biological entities present in outdoor air, causing allergy symptoms and disease transmission and having a significant role in atmosphere dynamics. Despite their relevance, a method for monitoring simultaneously these biological particles in metropolitan environments has not yet been developed. Here, we assessed the use of the Hirst-type spore trap to characterize the global airborne biota by high-throughput DNA sequencing, selecting regions of the 16S rRNA gene and internal transcribed spacer for the taxonomic assignment. We showed that aerobiological communities are well represented by this approach. The operational taxonomic units (OTUs) of two traps working synchronically compiled >87% of the total relative abundance for bacterial diversity collected in each sampler, >89% for fungi, and >97% for pollen. We found a good correspondence between traditional characterization by microscopy and genetic identification, obtaining more-accurate taxonomic assignments and detecting a greater diversity using the latter. We also demonstrated that DNA sequencing accurately detects differences in biodiversity between samples. We concluded that high-throughput DNA sequencing applied to aerobiological samples obtained with Hirst spore traps provides reliable results and can be easily implemented for monitoring prokaryotic and eukaryotic entities present in the air of urban areas. IMPORTANCE Detection, monitoring, and characterization of the wide diversity of biological entities present in the air are difficult tasks that require time and expertise in different disciplines. We have evaluated the use of the Hirst spore trap (an instrument broadly employed in aerobiological studies) to detect and identify these organisms by DNA-based analyses. Our results showed a consistent collection of DNA and a good concordance with traditional methods for identification, suggesting that these devices can be used as a tool for continuous monitoring of the airborne biodiversity, improving taxonomic resolution and characterization together. They are also suitable for acquiring novel DNA amplicon-based information in order to gain a better understanding of the biological particles present in a scarcely known environment such as the air. PMID:28455334

Activation of platelet-rich plasma using thrombin receptor agonist peptide.

PubMed

Landesberg, Regina; Burke, Andrea; Pinsky, David; Katz, Ronald; Vo, Jennifer; Eisig, Sidney B; Lu, Helen H

2005-04-01

This study proposes an alternative preparation method of platelet-rich plasma (PRP). Specifically, we compare the use of thrombin receptor agonist peptide-6 (TRAP) and bovine thrombin as a clotting agent in the preparation of PRP. PRP was prepared by centrifugation and clotted with thrombin or TRAP. In vitro clotting times were monitored as a function of TRAP concentration, and clot retraction was determined by measuring clot diameter over time. Following the optimization of TRAP concentration, experiments were repeated with the addition of several commercially available bone substitutes. The release of PRP-relevant growth factors as a function of PRP preparation was also determined. The most rapid polymerization of PRP takes place with the addition of thrombin, followed by TRAP/Allogro (Ceramed, Lakewood, CO), TRAP/BioGlass (Mo-Sci, Rolla, MN), TRAP/BioOss (Osteohealth, Shirley, NY), and TRAP alone. Thrombin caused considerable clot retraction (43%), whereas TRAP alone resulted in only 15% retraction. TRAP/Allogro, TRAP/BioOss, and TRAP/BioGlass all exhibited minimal retraction (8%). The use of TRAP to activate clot formation in the preparation of PRP may be a safe alternative to bovine thrombin. It results in an excellent working time and significantly less clot retraction than the currently available methods of PRP production.

Monitoring xenon purity in the LUX detector with a mass spectrometry system

NASA Astrophysics Data System (ADS)

Balajthy, Jon; LUX Experiment Collaboration

2015-04-01

The LUX dark matter search experiment is a 350 kg two-phase liquid/gas xenon time projection chamber located at the 4850 ft level of the Sanford Underground Research Facility in Lead, SD. To monitor for radioactive impurities such as krypton and impurities which limit charge yield such as oxygen, LUX uses a xenon sampling system consisting of a mass spectrometer and a liquid nitrogen cold trap. The cold trap separates the gaseous impurities from a small sample of xenon and allows them to pass to the mass spectrometer for analysis. We report here on results from the LUX xenon sampling program. We also report on methods to enhance the sensitivity of the cold trap technique in preparation for the next-generation LUX-ZEPLIN experiment which will have even more stringent purity requirements.

Automated Surveillance of Fruit Flies

PubMed Central

Potamitis, Ilyas; Rigakis, Iraklis; Tatlas, Nicolaos-Alexandros

2017-01-01

Insects of the Diptera order of the Tephritidae family cause costly, annual crop losses worldwide. Monitoring traps are important components of integrated pest management programs used against fruit flies. Here we report the modification of typical, low-cost plastic traps for fruit flies by adding the necessary optoelectronic sensors to monitor the entrance of the trap in order to detect, time-stamp, GPS tag, and identify the species of incoming insects from the optoacoustic spectrum analysis of their wingbeat. We propose that the incorporation of automated streaming of insect counts, environmental parameters and GPS coordinates into informative visualization of collective behavior will finally enable better decision making across spatial and temporal scales, as well as administrative levels. The device presented is at product level of maturity as it has solved many pending issues presented in a previously reported study. PMID:28075346

Direct Monitoring of Trace Atmospheric Species via Ion Trap Mass Spectrometry

NASA Technical Reports Server (NTRS)

Palmer, P. T.; Pearson, Richard; Saimonson, Jay D.; Wong, Carla M.; Lawless, James G. (Technical Monitor)

1994-01-01

There is an ever-increasing emphasis on the part of government agencies, academia, and industry on enhancing our understanding of atmospheric processes and assessing the impact of human activities on these processes. While issues such as the ozone hole and rising levels of greenhouse gases have received major attention. relatively little is known about the types, concentrations, sources, and sinks of hydrocarbons in the troposphere and stratosphere. Such information would be of tremendous utility in assessing the roles of various anthropogenic and biogenic processes on global carbon cycles. An ion trap mass spectrometer has been developed for monitoring trace levels of hydrocarbons in the atmosphere on NASA's DC-8 "flying laboratory". This aircraft is used to provide measurements in support of a number of "Mission to Planet Earth" activities and tropospheric chemistry experiments. In past missions, specific compounds have been monitored via highly specialized instrumentation, fast GO, or collection of whole air samples for subsequent ground-based analysis. The ion trap has several features. including small size. excellent sensitivity, and broad applicability, which make it highly atttrat:ive for atmospheric monitoring. The design of this instrument, its air sampling interface. and the various complications associated with aircraft-deployment will be described. Data showing the sensitivity of the instrument for detecting hydrocarbons at mixing ratios below one part-per-billion, and the use of MS/MS for direct, on-line, real-time monitoring will be presented.

Capture of breeding and wintering shorebirds with leg-hold noose-mats

USGS Publications Warehouse

Mehl, K.R.; Drake, K.L.; Page, G.W.; Sanzenbacher, Peter M.; Haig, Susan M.; Thompson, J.E.

2003-01-01

Development of effective trapping techniques is important for conservation efforts, as marking and subsequent monitoring of individuals is necessary to obtain accurate estimates of demography, movements, and habitat use. We describe a leg-hold noose-mat trap for capturing breeding and nonbreeding shorebirds. Using this method, we trapped 50 Piping Plovers (Charadrius melodus), 2258 Snowy Plovers (C. alexandrinus), 38 Killdeers (C. vociferus), and 64 Dunlins (Calidris alpina) in the western and southern United States. The trap was lightweight, making it easy to transport and set up. It was effective on unvegetated substrates at both coastal and inland sites and could be modified for a variety of habitats. Furthermore, this trap allowed researchers to target specific groups of birds including territorial individuals. Easy removal of birds from traps minimized handling time, stress, and injury

Determination of methylamines in air using activated charcoal traps and gas chromatographic analysis with an alkali flame detector (AFD)

NASA Astrophysics Data System (ADS)

Fuselli, Sergio; Benedetti, Giorgio; Mastrangeli, Renato

A method is described for trapping and analysing airborne methylamines (MMA, DMA and TMA) by means of a 20/35 mesh activated charcoal traps and subsequent GLSC analysis of collected sample using 0.1 N NaOH acqueous solution. The method described may be applied to monitoring methylamines in air in industrial areas, with an Alkali Flame Detector; sensitivities of approx. 0.005 ppmv for each of the three methylamines analysed are reached. Trapping efficiency is compared with that of Tenax GC 60/80 mesh and 60/80 Carbopack B which uses thermal desorption of air samples before GLSC analysis. The Tenax GC trap method enables TMA recovery only with a sensitivity of 0.0001 ppmv. Recovery obtained with 60/80 Carbopack B traps is practically zero.

Make your trappings count: The mathematics of pest insect monitoring. Comment on “Multiscale approach to pest insect monitoring: Random walks, pattern formation, synchronization, and networks” by Petrovskii et al.

NASA Astrophysics Data System (ADS)

Blasius, Bernd

2014-09-01

Since the beginnings of agriculture the production of crops is characterized by an ongoing battle between farmers and pests [1]. Already during biblical times swarms of the desert locust, Schistocerca gregaria, were known as major pest that can devour a field of corn within an hour. Even today, harmful organisms have the potential to threaten food production worldwide. It is estimated that about 37% of all potential crops are destroyed by pests. Harmful insects alone destroy 13%, causing financial losses in the agricultural industry of millions of dollars each year [2-4]. These numbers emphasize the importance of pest insect monitoring as a crucial step of integrated pest management [1]. The main approach to gain information about infestation levels is based on trapping, which leads to the question of how to extrapolate the sparse population counts at singularly disposed traps to a spatial representation of the pest species distribution. In their review Petrovskii et al. provide a mathematical framework to tackle this problem [5]. Their analysis reveals that this seemingly inconspicuous problem gives rise to surprisingly deep mathematical challenges that touch several modern contemporary concepts of statistical physics and complex systems theory. The review does not aim for a collection of numerical recipes to support crop growers in the analysis of their trapping data. Instead the review identifies the relevant biological and physical processes that are involved in pest insect monitoring and it presents the mathematical techniques that are required to capture these processes.

Development of the gravid Aedes trap for the capture of adult female container-exploiting mosquitoes (Diptera: Culicidae).

PubMed

Eiras, Alvaro E; Buhagiar, Tamara S; Ritchie, Scott A

2014-01-01

Monitoring dengue vector control by sampling adult Aedes aegypti (L.) recently has been used to replace both larval and pupal surveys. We have developed and evaluated the Gravid Aedes Trap (GAT) through a sequential behavioral study. The GAT does not require electricity to function, and trapped mosquitoes are identified easily during trap inspections. The GAT concept relies on visual and olfactory cues to lure gravid Ae. aegypti and an insecticide to kill trapped mosquitoes. Gravid mosquitoes are lured to a black bucket base containing oviposition attractant (infusion) and are trapped in a translucent chamber impregnated with a pyrethroid insecticide where they are killed within 3-15 min. In semifield observations, the GAT captured a significantly higher proportion of gravid mosquitoes than the double sticky ovitrap. We also demonstrated that the visual cues of the prototype GAT-LgBF (large black base bucket with a black funnel at the top of the translucent chamber) captured a significantly higher proportion of gravid mosquitoes than the other prototypes. The visual contrast created by the addition of a white lid to the top of the black funnel significantly increased the number of captured gravid mosquitoes when compared with the GAT-LgBF in semifield trials. We conclude that the GAT is more efficient in recapturing gravid Ae. aegypti when compared with sticky ovitraps. The GAT is an effective, practical, low cost, and easily transportable trap, features that are essential in large-scale monitoring programs, particularly in areas where funding is limited.

Traps and Baits for Luring Grapholita molesta (Busck) Adults in Mating Disruption-Treated Apple Orchards.

PubMed

Padilha, A C; Arioli, C J; Boff, M I C; Rosa, J M; Botton, M

2018-02-01

Grapholita molesta (Busck) is one of the main pests in apple crops in Brazil, where it is controlled by mating disruption (MD) with the use of the synthetic sex pheromone. However, sex-pheromone-based monitoring is not effective in MD-treated areas and may result in losses in production. This work has defined a trap model and a bait for luring G. molesta adults in MD apple orchards. The experiments were conducted in commercial apple orchards located in São Joaquim, SC, Brazil. Three trap models-McPhail, Pot, and Ajar-and three baits-grape juice (25%) (GJ), sugarcane molasses (25%) (SM), and a solution containing brown sugar (8.69%) and terpinyl acetate (0.05%) (TAS)-were assessed for luring G. molesta adults in areas subjected to the mating disruption. The assessments were performed weekly by collecting the insects caught in the traps. In addition, time needed to replace traps was also assessed, as well as the selectivity of the trap/bait set. In the laboratory, G. molesta adults were sexed, and the females were dissected to confirm reproductive status. We discuss our results and sugarcane molasses (25%) captured the least number of G. molesta adults regardless of the tested traps. The Ajar/TAS, Pot/TAS, and McPhail/GJ captured the largest number of G. molesta adults. The Ajar/TAS was the most selective and easier to handle. TAS was efficient in catching G. molesta until 14 days after preparation of the solution. Ajar/TAS has potential to be used in the monitoring of G. molesta in apple orchards.

Monitoring social indicators in the Bear Trap Canyon Wilderness 1988-1998

Treesearch

Joe L. Ashor

2000-01-01

Since its inception as a wilderness planning and management tool almost 15 years ago, the Limits of Acceptable Change (LAC) process has stressed the importance of monitoring. Monitoring social conditions is critical to ensure that quality visitor experiences are maintained. Ten years of data collected from monitoring three river corridor-related social indicators in...

40 CFR 63.9990 - What are the subcategories of EGUs?

Code of Federal Regulations, 2012 CFR

2012-07-01

... coal or gasified solid oil-derived fuel. For purposes of compliance, monitoring, recordkeeping, and...) National Emission Standards for Hazardous Air Pollutants: Coal- and Oil-Fired Electric Utility Steam... equal to 8,300 Btu/lb, and (2) EGUs designed for low rank virgin coal. (b) Oil-fired EGUs are...

40 CFR 63.9990 - What are the subcategories of EGUs?

Code of Federal Regulations, 2013 CFR

2013-07-01

... coal or gasified solid oil-derived fuel. For purposes of compliance, monitoring, recordkeeping, and...) National Emission Standards for Hazardous Air Pollutants: Coal- and Oil-Fired Electric Utility Steam... equal to 8,300 Btu/lb, and (2) EGUs designed for low rank virgin coal. (b) Oil-fired EGUs are...

40 CFR 63.9990 - What are the subcategories of EGUs?

Code of Federal Regulations, 2014 CFR

2014-07-01

... coal or gasified solid oil-derived fuel. For purposes of compliance, monitoring, recordkeeping, and...) National Emission Standards for Hazardous Air Pollutants: Coal- and Oil-Fired Electric Utility Steam... equal to 8,300 Btu/lb, and (2) EGUs designed for low rank virgin coal. (b) Oil-fired EGUs are...

Liquid level, void fraction, and superheated steam sensor for nuclear-reactor cores. [PWR; BWR

DOEpatents

Tokarz, R.D.

1981-10-27

This disclosure relates to an apparatus for monitoring the presence of coolant in liquid or mixed liquid and vapor, and superheated gaseous phases at one or more locations within an operating nuclear reactor core, such as pressurized water reactor or a boiling water reactor.

iss009e26364

NASA Image and Video Library

2004-10-01

ISS009-E-26364 (1 October 2004) --- Mount Saint Helens, Washington, is featured in this image photographed by an Expedition 9 crewmember on the International Space Station (ISS). The USGS has been monitoring Mount Saint Helens closely since last Thursday, when the volcano began to belch steam and swarms of tiny earthquakes were first recorded.

Correlation between y-type ions observed in ion trap and triple quadrupole mass spectrometers.

PubMed

Sherwood, Carly A; Eastham, Ashley; Lee, Lik Wee; Risler, Jenni; Vitek, Olga; Martin, Daniel B

2009-09-01

Multiple reaction monitoring mass spectrometry (MRM-MS) is a technique for high-sensitivity targeted analysis. In proteomics, MRM-MS can be used to monitor and quantify a peptide based on the production of expected fragment peaks from the selected peptide precursor ion. The choice of which fragment ions to monitor in order to achieve maximum sensitivity in MRM-MS can potentially be guided by existing MS/MS spectra. However, because the majority of discovery experiments are performed on ion trap platforms, there is concern in the field regarding the generalizability of these spectra to MRM-MS on a triple quadrupole instrument. In light of this concern, many operators perform an optimization step to determine the most intense fragments for a target peptide on a triple quadrupole mass spectrometer. We have addressed this issue by targeting, on a triple quadrupole, the top six y-ion peaks from ion trap-derived consensus library spectra for 258 doubly charged peptides from three different sample sets and quantifying the observed elution curves. This analysis revealed a strong correlation between the y-ion peak rank order and relative intensity across platforms. This suggests that y-type ions obtained from ion trap-based library spectra are well-suited for generating MRM-MS assays for triple quadrupoles and that optimization is not required for each target peptide.

Gallery productivity, emergence, and flight activity of the redbay ambrosia beetle (Coleoptera: Curculionidae: Scolytinae)

Treesearch

M. Lake Maner; James Hanula; S. Kristine Braman

2013-01-01

Flight and emergence of the redbay ambrosia beetle, Xyleborus glabratus Eichhoff, were monitored from March 2011 through August 2012 using Lindgren funnel traps baited with manuka oil and emergence traps attached over individual beetle galleries on infested redbay (Persea borbonia (L.) Sprengel) trees. Of the 432 gallery entrances...

Monitoring Oriental Fruit Moth (Lepidoptera: Tortricidae) and Peach Twig Borer (Lepidoptera: Gelechiidae) with Clear Delta-shaped Traps

USDA-ARS?s Scientific Manuscript database

Field studies evaluated the relative performance of a clear versus several colored delta traps baited with sex pheromone or a food bait for two key moth pests of stone fruits: oriental fruit moth, Graphollita molesta (Busck); and peach twig borer, Anarsia lineatella Zeller. Preliminary studies found...

Swarming of the Formosan Subteranean Termite (Isoptera: Rhinotermitidae) in Southern Mississippi

USDA-ARS?s Scientific Manuscript database

Swarms of Formosan subterranean termites (FST) in Southern Mississippi were monitored from mid-April through late June, 2007-2009. Distribution of swarming colonies was recorded at 69 traps within Poplarville (Pearl River County) and an additional 45-65 traps, spaced at 1-5 mile (1.6-8 km) intervals...

Pheromone-food-bait trap and acoustic surveys of Rhynchophorus Ferrugineus (Coleoptera:Curculionidae)in Curacao

USDA-ARS?s Scientific Manuscript database

Pheromone-food-bait trap and acoustic surveys were conducted in Curacao to monitor a recently discovered invasion of Rhynchophorus ferrugineus L. (RPW). This pest of economic importance in regions of Asia, the Middle East, and the Mediterranean was not observed in the Americas until 2009. Due to its...

Mountain pine beetle population sampling: inferences from Lindgren pheromone traps and tree emergence cages

Treesearch

Barbara J. Bentz

2006-01-01

Lindgren pheromone traps baited with a mountain pine beetle (Dendroctonus ponderosae Hopkins (Coleoptera: Curculionidae, Scolytinae)) lure were deployed for three consecutive years in lodgepole pine stands in central Idaho. Mountain pine beetle emergence was also monitored each year using cages on infested trees. Distributions of beetles caught in...

Camera trapping estimates of density and survival of fishers (Martes pennanti)

Treesearch

Mark J. Jordan; Reginald H. Barrett; Kathryn L. Purcell

2011-01-01

Developing efficient monitoring strategies for species of conservation concern is critical to ensuring their persistence. We have developed a method using camera traps to estimate density and survival in mesocarnivores and tested it on a population of fishers Martes pennanti in an area of approximately 300 km2 of the southern...

Factors affecting the efficacy of a vinegar trap for Drosophila suzukii (Diptera: Drosophilidae)

USDA-ARS?s Scientific Manuscript database

Studies were conducted to develop an optimized, economical trap for monitoring the spotted wing fruit fly, Drosophila suzukii Matsumura. Flies were attracted to dark colors ranging from red to black compared with low attraction to white, yellow, and light blue. Similarly, fly catches in 237 ml plast...

Double-deckers and towers: emerald ash borer traps in 2007

Treesearch

Deborah G. McCullough; Therese M. Poland; Andrea C. Anulewicz; David L. Cappaert

2008-01-01

Effective and efficient methods to detect and monitor emerald ash borer (EAB), Agrilus planipennis Fairmaire, have been a high priority for scientists since this invasive pest was identified in 2002. In 2006, our objectives included development of a practical trap design suitable for operational programs and evaluation of lures. In 2007, we continued...

Monitoring sperm mitochondrial respiration response in a laser trap using ratiometric fluorescence

NASA Astrophysics Data System (ADS)

Mei, Adrian; Botvinick, Elliot; Berns, Michael

2005-08-01

Sperm motility is an important area in understanding male infertility. Various techniques, such as the Computer Assisted Sperm Analysis (CASA), have been used to understand sperm motility. Sperm motility is related to the energy (ATP) production of sperm. ATP is produced by the depolarization of the membrane potential of the inner membrane of the mitochondria. In this study, a mitochondrial dye, JC-1, has been used to monitor the energetics of the mitochondria. This fluorescent dye can emit at two different wavelengths, depending on the membrane potential of the mitochondria. It can fluoresce green at low membrane potential and red at high membrane potential. The ratio of the two colors (red/green) allows for an accurate measurement of the change of membrane potential. Various experiments were conducted to quantify the behavior of the dye within the sperm and the reaction of the sperm to trap. Sperm were trapped using laser tweezers. Results have shown that the ratio drops dramatically when sperm are trapped, indicating a depolarization of the membrane. The physiological response to this depolarization is yet to be determined, but the studies indicate that the sperm could have been slightly damaged by the laser. However, knowing that sperm depolarizes their membrane when trapped can help understand how sperm react to their environment and consequently help treat male infertility.

The use (and misuse) of sediment traps in coral reef environments: theory, observations, and suggested protocols

NASA Astrophysics Data System (ADS)

Storlazzi, C. D.; Field, M. E.; Bothner, M. H.

2011-03-01

Sediment traps are commonly used as standard tools for monitoring "sedimentation" in coral reef environments. In much of the literature where sediment traps were used to measure the effects of "sedimentation" on corals, it is clear from deployment descriptions and interpretations of the resulting data that information derived from sediment traps has frequently been misinterpreted or misapplied. Despite their widespread use in this setting, sediment traps do not provide quantitative information about "sedimentation" on coral surfaces. Traps can provide useful information about the relative magnitude of sediment dynamics if trap deployment standards are used. This conclusion is based first on a brief review of the state of knowledge of sediment trap dynamics, which has primarily focused on traps deployed high above the seabed in relatively deep water, followed by our understanding of near-bed sediment dynamics in shallow-water environments that characterize coral reefs. This overview is followed by the first synthesis of near-bed sediment trap data collected with concurrent hydrodynamic information in coral reef environments. This collective information is utilized to develop nine protocols for using sediment traps in coral reef environments, which focus on trap parameters that researchers can control such as trap height ( H), trap mouth diameter ( D), the height of the trap mouth above the substrate ( z o ), and the spacing between traps. The hydrodynamic behavior of sediment traps and the limitations of data derived from these traps should be forefront when interpreting sediment trap data to infer sediment transport processes in coral reef environments.

The use (and misuse) of sediment traps in coral reef environments: Theory, observations, and suggested protocols

USGS Publications Warehouse

Storlazzi, C.D.; Field, M.E.; Bothner, Michael H.

2011-01-01

Sediment traps are commonly used as standard tools for monitoring “sedimentation” in coral reef environments. In much of the literature where sediment traps were used to measure the effects of “sedimentation” on corals, it is clear from deployment descriptions and interpretations of the resulting data that information derived from sediment traps has frequently been misinterpreted or misapplied. Despite their widespread use in this setting, sediment traps do not provide quantitative information about “sedimentation” on coral surfaces. Traps can provide useful information about the relative magnitude of sediment dynamics if trap deployment standards are used. This conclusion is based first on a brief review of the state of knowledge of sediment trap dynamics, which has primarily focused on traps deployed high above the seabed in relatively deep water, followed by our understanding of near-bed sediment dynamics in shallow-water environments that characterize coral reefs. This overview is followed by the first synthesis of near-bed sediment trap data collected with concurrent hydrodynamic information in coral reef environments. This collective information is utilized to develop nine protocols for using sediment traps in coral reef environments, which focus on trap parameters that researchers can control such as trap height (H), trap mouth diameter (D), the height of the trap mouth above the substrate (z o ), and the spacing between traps. The hydrodynamic behavior of sediment traps and the limitations of data derived from these traps should be forefront when interpreting sediment trap data to infer sediment transport processes in coral reef environments.

Camera Traps Can Be Heard and Seen by Animals

PubMed Central

Meek, Paul D.; Ballard, Guy-Anthony; Fleming, Peter J. S.; Schaefer, Michael; Williams, Warwick; Falzon, Greg

2014-01-01

Camera traps are electrical instruments that emit sounds and light. In recent decades they have become a tool of choice in wildlife research and monitoring. The variability between camera trap models and the methods used are considerable, and little is known about how animals respond to camera trap emissions. It has been reported that some animals show a response to camera traps, and in research this is often undesirable so it is important to understand why the animals are disturbed. We conducted laboratory based investigations to test the audio and infrared optical outputs of 12 camera trap models. Camera traps were measured for audio outputs in an anechoic chamber; we also measured ultrasonic (n = 5) and infrared illumination outputs (n = 7) of a subset of the camera trap models. We then compared the perceptive hearing range (n = 21) and assessed the vision ranges (n = 3) of mammals species (where data existed) to determine if animals can see and hear camera traps. We report that camera traps produce sounds that are well within the perceptive range of most mammals’ hearing and produce illumination that can be seen by many species. PMID:25354356

Evaluation of a new rapid readout biological indicator for use in 132°C and 135°C vacuum-assisted steam sterilization cycles.

PubMed

Schneider, Philip M

2014-02-01

Sterilization is a process that cannot be inspected or tested in a practical manner to assure that all microorganisms have been inactivated. The process must therefore be validated for all of the specific items processed or monitored on a per cycle basis. A new, faster rapid readout biological indicator (RRBI) has been developed for use in 132°C and 135°C vacuum-assisted steam sterilization cycles. The aim of this study was to evaluate the performance of this new 1-hour readout RRBI at 132°C in side-by-side testing with an existing 3-hour readout RRBI and also evaluate the performance of the new RRBI in 135°C cycles. Readout responses of 1 hour (fluorescent) and 48 hours and 7 days (growth) of the new RRBI were compared with 3-hour, 48-hour, and 7-day readouts of the 3-hour RRBI following exposures in 132°C cycles using a highly controlled test vessel, ie, a steam resistometer. Additional testing of the 1-hour RRBIs was also performed in 135°C cycles. The number and percentage of fluorescent-positive 1-hour RRBIs were virtually identical to those of the 3-hour RRBIs after 1 and 3 hours of incubation, respectively. Testing of the 1-hour RRBI in 135°C cycles paralleled the results of the testing at 132°C but with the expected shorter exposure times. The results of this study suggest that the 1-hour RRBI is equivalent to the 3-hour RRBI and would be suitable for use in monitoring dynamic air removal steam sterilization cycles at both 132°C and 135°C per recommended practice guidelines. Copyright © 2014 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Mosby, Inc. All rights reserved.

Smolt Monitoring at the Head of Lower Granite Reservoir and Lower Granite Dam; Smolt Monitoring by Federal and Non-Federal Entities, 2001-2002 Annual Report.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Buettner, Edwin W.; Putnam, Scott A.

This project monitored the daily passage of chinook salmon Oncorhynchus tshawytscha, steelhead trout O. mykiss, and sockeye salmon smolts O. nerka during the 2001 spring out-migration at migrant traps on the Snake River and Salmon River. In 2001 fish management agencies released significant numbers of hatchery chinook salmon and steelhead trout above Lower Granite Dam that were not marked with a fin clip or coded-wire tag. Generally, these fish were distinguishable from wild fish by the occurrence of fin erosion. Total annual hatchery chinook salmon catch at the Snake River trap was 11% of the 2000 numbers. The wild chinookmore » catch was 3% of the previous year's catch. Hatchery steelhead trout catch was 49% of 2000 numbers. Wild steelhead trout catch was 69% of 2000 numbers. The Snake River trap collected 28 age-0 chinook salmon. During 2001 the Snake River trap captured zero hatchery and zero wild/natural sockeye salmon and six hatchery coho salmon O. kisutch. Differences in trap catch between years are due to fluctuations not only in smolt production, but also differences in trap efficiency and duration of trap operation associated with flow. The significant reduction in catch during 2001 was due to a reduction in hatchery chinook production (60% of 2000 release) and due to extreme low flows. Trap operations began on March 11 and were terminated on June 29. The trap was out of operation for a total of two days due to mechanical failure or debris. Hatchery chinook salmon catch at the Salmon River trap was 47% and wild chinook salmon catch was 67% of 2000 numbers. The hatchery steelhead trout collection in 2001 was 178% of the 2000 numbers. Wild steelhead trout collection in 2001 was 145% of the previous year's catch. Trap operations began on March 11 and were terminated on June 8 due to the end of the smolt monitoring season. There were no days where the trap was out of operation due to high flow or debris. The decrease in hatchery chinook catch in 2001 was due to a reduction in hatchery production (39% of 2000 releases). The increase in hatchery and wild steelhead trap catch is due to the ability to operate the trap in the thalweg for a longer period of time because of the extreme low flow condition in 2001. Travel time (d) and migration rate (km/d) through Lower Granite Reservoir for PIT-tagged chinook salmon and steelhead trout marked at the head of the reservoir were affected by discharge. There were not enough hatchery and wild chinook salmon tagged at the Snake River trap in 2001 to allow migration rate/discharge analysis. For steelhead trout tagged at the Snake River trap, statistical analysis of 2001 data detected a significant relation between migration rate and Lower Granite Reservoir inflow discharge. For hatchery and wild steelhead trout, there was a 2.2-fold and a 1.5-fold increase in migration rate in, respectively, between 50 and 100 kcfs. Travel time and migration rate to Lower Granite Dam for fish marked at the Salmon River trap were calculated. Statistical analysis of the 2001 data detected a significant relation between migration rate and Lower Granite Reservoir inflow discharge for hatchery and wild chinook salmon and hatchery and wild steelhead trout. Migration rate increased 3.7-fold for hatchery chinook salmon and 2.5-fold for wild chinook salmon between 50 and 100 kcfs. For hatchery steelhead there was a 1.6-fold increase in migration rate, and for wild steelhead trout there was a 2.2-fold increase between 50 kcfs and 100 kcfs. Fish tagged with passive integrated transponder (PIT) tags at the Snake River trap were interrogated at four dams with PIT tag detection systems (Lower Granite, Little Goose, Lower Monumental, and McNary dams). Because of the addition of the fourth interrogation site (Lower Monumental) in 1993, cumulative interrogation data is not comparable with the prior five years (1988-1992). Cumulative interrogations at the four dams for fish marked at the Snake River trap were 86% for hatchery chinook, 70% for wild chinook, 71% for hatchery steelhead, and 89% for wild steelhead. Cumulative interrogations at the four dams for fish marked at the Salmon River trap were 74% for hatchery chinook, 83% for wild chinook salmon, 75% for hatchery steelhead trout, and 81% for wild steelhead trout.« less

Restoration of the USS Monitor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krop, David

2010-03-02

David Krop will discuss the ongoing efforts to conserve and exhibit the iconic Civil War ironclad USS Monitor at The Mariners' Museum. The presentation will cover past conservation accomplishments by conservators and NOAA specialists, current activities in the lab, and future plans to bring back to life one of the world's most famous warships. Learn about the complex methods and procedures used to treat the ship's revolving gun turret, steam engine, Dahlgren guns and carriages, as well as numerous small artifacts like personal items from the crew.

A cost-effective, community-based, mosquito-trapping scheme that captures spatial and temporal heterogeneities of malaria transmission in rural Zambia

PubMed Central

2014-01-01

Background Monitoring mosquito population dynamics is essential to guide selection and evaluation of malaria vector control interventions but is typically implemented by mobile, centrally-managed teams who can only visit a limited number of locations frequently enough to capture longitudinal trends. Community-based (CB) mosquito trapping schemes for parallel, continuous monitoring of multiple locations are therefore required that are practical, affordable, effective, and reliable. Methods A CB surveillance scheme, with a monthly sampling and reporting cycle for capturing malaria vectors, using Centers for Disease Control and Prevention light traps (LT) and Ifakara Tent Traps (ITT), were conducted by trained community health workers (CHW) in 14 clusters of households immediately surrounding health facilities in rural south-east Zambia. At the end of the study, a controlled quality assurance (QA) survey was conducted by a centrally supervised expert team using human landing catch (HLC), LT and ITT to evaluate accuracy of the CB trapping data. Active surveillance of malaria parasite infection rates amongst humans was conducted by CHWs in the same clusters to determine the epidemiological relevance of these CB entomological surveys. Results CB-LT and CB-ITT exhibited relative sampling efficiencies of 50 and 7%, respectively, compared with QA surveys using the same traps. However, cost per sampling night was lowest for CB-LT ($13.6), followed closely by CB-ITT ($18.0), both of which were far less expensive than any QA survey (HLC: $138, LT: $289, ITT: $269). Cost per specimen of Anopheles funestus captured was lowest for CB-LT ($5.3), followed by potentially hazardous QA-HLC ($10.5) and then CB-ITT ($28.0), all of which were far more cost-effective than QA-LT ($141) and QA-ITT ($168). Time-trends of malaria diagnostic positivity (DP) followed those of An. funestus density with a one-month lag and the wide range of mean DP across clusters was closely associated with mean densities of An. funestus caught by CB-LT (P < 0.001). Conclusions CB trapping schemes appear to be far more affordable, epidemiologically relevant and cost-effective than centrally supervised trapping schemes and may well be applicable to enhance intervention trials and even enable routine programmatic monitoring of vector population dynamics on unprecedented national scales. PMID:24906704

Survey on prevacuum high-pressure steam sterilizers

PubMed Central

Darmady, E. M.; Drewett, S. E.; Hughes, K. E. A.

1964-01-01

None of the 10 prevacuum high-pressure sterilizers of different makes tested was able to produce and maintain the conditions advocated by the Medical Research Council working party on high-pressure steam sterilizers (1959) or by Knox and Penikett (1958) with the result that steam did not penetrate adequately the single challenge load and it was not sterilized. The sterilization of `group drums' of various sizes and contents was erratic and tended to give operators a false sense of security. An alarming number of minor engineering faults were present in seven out of 10 machines tested and they require very much more skilled maintenance than is being given at the moment. The possibility of centralizing sterilizers to central sterile supply departments and placing them under the care of a regional engineer cannot be too highly recommended. The presence of undetected `leaks' and a failure to draw a prevacuum of 20 mm. even with a steam burst interferes with sterilization of a challenge load. A leak test should be performed twice daily and should not exceed more than 1 mm. in one minute at 20 mm. absolute. The centre of the load should be monitored by crossed tapes or Brownes tubes in each sterilizing cycle. Although the challenge load was sterilized when the chamber was filled to capacity, a more reliable cycle consisting of a double prevacuum of 20 mm. or more with intermediate steam burst to 10 lb. ensured the sterilizing of a single challenge load, which could be adequately controlled by the chamber drain temperature. PMID:14149935

First Report of Zaprionus indianus (Diptera: Drosophilidae) in Commercial Fruits and Vegetables in Pennsylvania

PubMed Central

Joshi, Neelendra K.; Biddinger, David J.; Demchak, Kathleen; Deppen, Alan

2014-01-01

Abstract Zaprionus indianus (Gupta) (Diptera: Drosophilidae), an invasive vinegar fly, was found for the first time in Adams County, Pennsylvania, in 2011. It was found in a commercial tart cherry orchard using apple cider vinegar (ACV) traps that were monitoring another invasive vinegar fly, the spotted wing drosophila, Drosophila suzukii (Matsumura) (Diptera: Drosophilidae). Coincidentally, the first record of D. suzukii found in Pennsylvania was also found in this same cherry orchard only 3 months earlier as part of a spotted wing drosophila survey effort in raspberry, blackberry, grape, and tart cherry in Adams County. These same crops plus blueberry and tomato were monitored again in 2012. In this article, adult Z. indianus captures in ACV traps and other traps deployed in the aforementioned crops during 2012 season are presented and the economic importance of Z. indianus is discussed. PMID:25434039

Determination of the NOx Loading of an Automotive Lean NOx Trap by Directly Monitoring the Electrical Properties of the Catalyst Material Itself

PubMed Central

Fremerey, Peter; Reiß, Sebastian; Geupel, Andrea; Fischerauer, Gerhard; Moos, Ralf

2011-01-01

Recently, it has been shown that the degree of loading of several types of automotive exhaust aftertreatment devices can be directly monitored in situ and in a contactless way by a microwave-based method. The goal of this study was to clarify whether this method can also be applied to NOx storage and reduction catalysts (lean NOx traps) in order to obtain further knowledge about the reactions occurring in the catalyst and to compare the results with those obtained by wirebound NOx loading sensors. It is shown that both methods are able to detect the different catalyst loading states. However, the sensitivity of the microwave-based method turned out to be small compared to that previously observed for other exhaust aftertreatment devices. This may limit the practical applicability of the microwave-based NOx loading detection in lean NOx traps. PMID:22164074

Charge carriers' trapping states in pentacene films studied by modulated photocurrent

NASA Astrophysics Data System (ADS)

Gorgolis, S.; Giannopoulou, A.; Kounavis, P.

2013-03-01

The modulated photocurrent (MPC) technique is employed to study the charge carriers' trapping states of pentacene films. The characteristics of the experimental MPC spectra were found to be compatible with trapping-detrapping process of holes in gap states in which their occupancy can be modified by the bias illumination. A demarcation energy level separating empty from partially occupied traps was deduced from the MPC spectra, which can be used to monitor bias-light induced changes in the quasi Fermi level. An exponential trap distribution from structural disorder and a deep metastable gaussian trap distribution from adsorbed environmental impurities were extracted by means of the MPC spectroscopy. An attempt to escape frequency of the order of 1010s-1 was deduced for the gap sates. The derived trap distributions agree with those found before by means of other techniques. The present results indicate that the MPC technique can be used as a valuable tool for pentacene films characterization since it can be also applied to field effect samples.

Sustainable Remediation for Enhanced NAPL Recovery from Groundwater

NASA Astrophysics Data System (ADS)

Javaher, M.

2012-12-01

Sustainable remediation relates to the achievement of balance between environmental, social, and economic elements throughout the remedial lifecycle. A significant contributor to this balance is the use of green and sustainable technologies which minimize environmental impacts, while maximizing social and economic benefits of remedial implementation. To this end, a patented mobile vapor energy generation (VEG) technology has been developed targeting variable applications, including onsite soil remediation for unrestricted reuse and enhanced non-aqueous phase liquid (NAPL) recover at the water table. At the core of the mobile VEG technology is a compact, high efficiency vapor generator, which utilizes recycled water and propane within an entirely enclosed system to generate steam as high as 1100°F. Operating within a fully enclosed system and capturing all heat that is generated within this portable system, the VEG technology eliminates all emissions to the atmosphere and yields an undetected carbon footprint with resulting carbon dioxide concentrations that are below ambient levels. Introduction of the steam to the subsurface via existing wells results in a desired change in the NAPL viscosity and the interfacial tension at the soil, water, NAPL interface; in turn, this results in mobilization and capture of the otherwise trapped, weathered NAPL. Approved by the California Air Resources Control Board (and underlying Air Quality Management Districts) and applied in California's San Joaquin Valley, in-well heating of NAPLs trapped at the water table using the VEG technology has proven as effective as electrical resistivity heating (ERH) in changing the viscosity of and mobilizing NAPLs in groundwater in support of recovery, but has achieved these results while minimizing the remedial carbon footprint by 90%, reducing energy use by 99%, and reducing remedial costs by more than 95%. NAPL recovery using VEG has also allowed for completion of source removal historically stalled, thereby eliminating ongoing and future groundwater impacts; in turn, this has increased project efficiency and stakeholder satisfaction by as much as 100%.

Influence of trap color and host volatiles on capture of the emerald ash borer (Coleoptera: Buprestidae).

PubMed

Crook, Damon J; Khrimian, Ashot; Cossé, Allard; Fraser, Ivich; Mastro, Victor C

2012-04-01

Field trapping assays were conducted in 2009 and 2010 throughout western Michigan, to evaluate lures for adult emerald ash borer, A. planipennis Fairmaire (Coleoptera: Buprestidae). Several ash tree volatiles were tested on purple prism traps in 2009, and a dark green prism trap in 2010. In 2009, six bark oil distillate lure treatments were tested against manuka oil lures (used in 2008 by USDA APHIS PPQ emerald ash borer cooperative program). Purple traps baited with 80/20 (manuka/phoebe oil) significantly increased beetle catch compared with traps baited with manuka oil alone. In 2010 we monitored emerald ash borer attraction to dark green traps baited with six lure combinations of 80/20 (manuka/phoebe), manuka oil, and (3Z)-hexenol. Traps baited with manuka oil and (3Z)-hexenol caught significantly more male and total count insects than traps baited with manuka oil alone. Traps baited with manuka oil and (3Z)-hexenol did not catch more beetles when compared with traps baited with (3Z)-hexenol alone. When compared with unbaited green traps our results show that (3Z)-hexenol improved male catch significantly in only one of three field experiments using dark green traps. Dark green traps caught a high number of A. planipennis when unbaited while (3Z)-hexenol was seen to have a minimal (nonsignificant) trap catch effect at several different release rates. We hypothesize that the previously reported kairomonal attractancy of (3Z)-hexenol (for males) on light green traps is not as obvious here because of improved male attractancy to the darker green trap.

Evaluation of pheromone-baited traps for the monitoring and management of nuisance problems associated with the invasive brown marmorated stink bug

USDA-ARS?s Scientific Manuscript database

The brown marmorated stink bug, or Halyomorpha halys, is an invasive species from southeast Asia, and has caused extensive agricultural damage in North America and Europe. Pheromone-based technology has been developed over the past 10 years, and when combined with appropriate traps, is highly effect...

Attraction of Agrilus planipennis (Coleoptera: Buprestidae) and other buprestids to sticky traps of various colors and shapes

Treesearch

Toby R. Petrice; Robert A. Haack; Therese M. Poland

2013-01-01

The family Buprestidae (Coleoptera) contains numerous economically significant species, including the emerald ash borer (EAB), Agrilus planipennis Fairmaire, first discovered in North America in 2002. Effective traps for monitoring spread and population densities of EAB and other buprestids are needed. Studies were conducted in 2008 to test different...

Amphibian breeding phenology and reproductive outcome: an examination using terrestrial and aquatic sampling

Treesearch

C.H. Greenberg; S.A. Johnson; R. Owen; A. Storfer

2017-01-01

Worldwide amphibian declines highlight the need for programs that monitor species presence and track population trends. We sampled larval amphibians with a box trap at 3-week intervals for 23 months in eight wetlands, and concurrently trapped adults and juveniles with drift fences, to examine spatiotemporal patterns of tadpole occurrence; explore relationships between...

Spatial displacement of a lure component can reduce catches of two nontarget species during spring monitoring of southern pine beetle

Treesearch

William P Shepherd; Brian T Sullivan

2017-01-01

Local outbreak risk for the southern pine beetle, Dendroctonus frontalis Zimmermann (Coleoptera: Curculionidae),is forecast with a trapping survey conducted every spring throughout the southeastern United States. Traps baitedwith pine odors and components of the D. frontalis aggregation pheromone are used to obtain abundance estimates

Measurements of key life history metrics of Coho salmon in Pudding Creek, California

Treesearch

David W. Wright; Sean P. Gallagher; Christopher J. Hannon

2012-01-01

Since 2005, a life cycle monitoring project in Pudding Creek, California, has utilized a variety of methodologies including an adult trap, spawning surveys, PIT tags, electro-fishing, and a smolt trap to estimate coho salmon adult escapement, juvenile abundance, juvenile growth, winter survival, and marine survival. Adult coho salmon escapement and smolt abundance are...

An ex situ evaluation of TBA- and MTBE-baited bio-traps.

PubMed

North, Katharine P; Mackay, Douglas M; Annable, Michael D; Sublette, Kerry L; Davis, Greg; Holland, Reef B; Petersen, Daniel; Scow, Kate M

2012-08-01

Aquifer microbial communities can be investigated using Bio-traps(®) ("bio-traps"), passive samplers containing Bio-Sep(®) beads ("bio-beads") that are deployed in monitoring wells to be colonized by bacteria delivered via groundwater flow through the well. When bio-beads are "baited" with organic contaminants enriched in (13)C, stable isotope probing allows assessment of the composition and activity of the microbial community. This study used an ex situ system fed by groundwater continuously extracted from an adjacent monitoring well within an experimentally-created aerobic zone treating a tert-butyl alcohol (TBA) plume. The goal was to evaluate aspects of bio-trap performance that cannot be studied quantitatively in situ. The measured groundwater flow through a bio-trap housing suggests that such traps might typically "sample" about 1.8 L per month. The desorption of TBA or methyl tert-butyl ether (MTBE) bait from bio-traps during a typical deployment duration of 6 weeks was approximately 90% and 45%, respectively, of the total initial bait load, with initially high rate of mass loss that decreased markedly after a few days. The concentration of TBA in groundwater flowing by the TBA-baited bio-beads was estimated to be as high as 3400 mg/L during the first few days, which would be expected to inhibit growth of TBA-degrading microbes. Initial inhibition was also implied for the MTBE-baited bio-trap, but at lower concentrations and for a shorter time. After a few days, concentrations in groundwater flowing through the bio-traps dropped below inhibitory concentrations but remained 4-5 orders of magnitude higher than TBA or MTBE concentrations within the aquifer at the experimental site. Desorption from the bio-beads during ex situ deployment occurred at first as predicted by prior sorption analyses of bio-beads but with apparent hysteresis thereafter, possibly due to mass transfer limitations caused by colonizing microbes. These results suggest that TBA- or MTBE-baited bio-traps could be baited at lower initial total mass loading with no detriment to trapping ability. The bio-traps were able to collect detectable amounts of microbial DNA and thus allow some insight into the sparse microbial community present in the aquifer during remediation of the low concentration plume. Copyright © 2012 Elsevier Ltd. All rights reserved.

Noninvasive and cost-effective trapping method for monitoring sensitive mammal populations

Treesearch

Stephanie E. Trapp; Elizabeth A. Flaherty

2017-01-01

Noninvasive sampling methods provide a means to monitor endangered, threatened, or sensitive species or populations while increasing the efficacy of personnel effort and time. We developed a monitoring protocol that utilizes single-capture hair snares and analysis of morphological features of hair for evaluating populations. During 2015, we used the West Virginia...

Abiotic factors and trap design modulate the performance of traps used to monitor the plum curculio.

PubMed

Lamothe, Steve; Chouinard, Gérald; Vincent, Charles

2008-12-01

All published studies on effects of abiotic factors on plum curculio, Conotrachelus nenuphar (Hersbt), adults have taken a retrospective approach. Here, we present the results of experiments where factors and their levels were determined and controlled a priori. We compared the effectiveness of miniature pyramidal traps (45 by 20 by 20 cm) constructed of four kind of materials--wood, geotextile, nylon screening, and corrugated plastic--to monitor overwintered and summer adults of univoltine plum curculio. We also studied the effects of photoperiod, temperature, wind, and rain on pyramidal trap effectiveness. The experiments, which were replicated over time, were done in two controlled chambers that were divided into four sections, corresponding to simulated combinations (wind or no wind/rain or no rain). The temperatures tested (15, 20, and 25 degrees C) were randomly assigned in the chambers. During scotophase, geotextile traps captured significantly more overwintered and summer adults than traps made of other materials. The maximum proportion of captures (for overwintered and summer adults) during photophase was obtained at 25 degrees C, and it was significantly different than captures at 15 and 20 degrees C. During scotophase, significantly more overwintered and summer plum curculios were caught at 20 and 25 degrees C than at 15 degrees C. Our experiments demonstrated that geotextile is a good alternative to wooden pyramidal trap. Our results suggest that captures were higher 1) at night, 2) during warmer periods (20 and 25 degrees C), 3) when wind velocity was low and 4) during or shortly after rainfall, and 5) that photoperiod is a factor having an important predictive value for plum curculio captures.

Screening the Hanford tanks for trapped gas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Whitney, P.

1995-10-01

The Hanford Site is home to 177 large, underground nuclear waste storage tanks. Hydrogen gas is generated within the waste in these tanks. This document presents the results of a screening of Hanford`s nuclear waste storage tanks for the presence of gas trapped in the waste. The method used for the screening is to look for an inverse correlation between waste level measurements and ambient atmospheric pressure. If the waste level in a tank decreases with an increase in ambient atmospheric pressure, then the compressibility may be attributed to gas trapped within the waste. In this report, this methodology ismore » not used to estimate the volume of gas trapped in the waste. The waste level measurements used in this study were made primarily to monitor the tanks for leaks and intrusions. Four measurement devices are widely used in these tanks. Three of these measure the level of the waste surface. The remaining device measures from within a well embedded in the waste, thereby monitoring the liquid level even if the liquid level is below a dry waste crust. In the past, a steady rise in waste level has been taken as an indicator of trapped gas. This indicator is not part of the screening calculation described in this report; however, a possible explanation for the rise is given by the mathematical relation between atmospheric pressure and waste level used to support the screening calculation. The screening was applied to data from each measurement device in each tank. If any of these data for a single tank indicated trapped gas, that tank was flagged by this screening process. A total of 58 of the 177 Hanford tanks were flagged as containing trapped gas, including 21 of the 25 tanks currently on the flammable gas watch list.« less

Thermoelectrically cooled water trap

DOEpatents

Micheels, Ronald H [Concord, MA

2006-02-21

A water trap system based on a thermoelectric cooling device is employed to remove a major fraction of the water from air samples, prior to analysis of these samples for chemical composition, by a variety of analytical techniques where water vapor interferes with the measurement process. These analytical techniques include infrared spectroscopy, mass spectrometry, ion mobility spectrometry and gas chromatography. The thermoelectric system for trapping water present in air samples can substantially improve detection sensitivity in these analytical techniques when it is necessary to measure trace analytes with concentrations in the ppm (parts per million) or ppb (parts per billion) partial pressure range. The thermoelectric trap design is compact and amenable to use in a portable gas monitoring instrumentation.

Herpetological Monitoring Using a Pitfall Trapping Design in Southern California

USGS Publications Warehouse

Fisher, Robert; Stokes, Drew; Rochester, Carlton; Brehme, Cheryl; Hathaway, Stacie; Case, Ted

2008-01-01

The steps necessary to conduct a pitfall trapping survey for small terrestrial vertebrates are presented. Descriptions of the materials needed and the methods to build trapping equipment from raw materials are discussed. Recommended data collection techniques are given along with suggested data fields. Animal specimen processing procedures, including toe- and scale-clipping, are described for lizards, snakes, frogs, and salamanders. Methods are presented for conducting vegetation surveys that can be used to classify the environment associated with each pitfall trap array. Techniques for data storage and presentation are given based on commonly use computer applications. As with any study, much consideration should be given to the study design and methods before beginning any data collection effort.

40 CFR 60.1810 - How do I monitor the load of my municipal waste combustion unit?

Code of Federal Regulations, 2012 CFR

2012-07-01

... municipal waste combustion unit? 60.1810 Section 60.1810 Protection of Environment ENVIRONMENTAL PROTECTION... Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30... combustion unit? (a) If your municipal waste combustion unit generates steam, you must install, calibrate...

40 CFR 60.1810 - How do I monitor the load of my municipal waste combustion unit?

Code of Federal Regulations, 2011 CFR

2011-07-01

... municipal waste combustion unit? 60.1810 Section 60.1810 Protection of Environment ENVIRONMENTAL PROTECTION... Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30... combustion unit? (a) If your municipal waste combustion unit generates steam, you must install, calibrate...

40 CFR 60.1810 - How do I monitor the load of my municipal waste combustion unit?

Code of Federal Regulations, 2013 CFR

2013-07-01

... municipal waste combustion unit? 60.1810 Section 60.1810 Protection of Environment ENVIRONMENTAL PROTECTION... Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30... combustion unit? (a) If your municipal waste combustion unit generates steam, you must install, calibrate...

40 CFR 60.1810 - How do I monitor the load of my municipal waste combustion unit?

Code of Federal Regulations, 2010 CFR

2010-07-01

... municipal waste combustion unit? 60.1810 Section 60.1810 Protection of Environment ENVIRONMENTAL PROTECTION... Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30... combustion unit? (a) If your municipal waste combustion unit generates steam, you must install, calibrate...

40 CFR 60.1810 - How do I monitor the load of my municipal waste combustion unit?

Code of Federal Regulations, 2014 CFR

2014-07-01

... municipal waste combustion unit? 60.1810 Section 60.1810 Protection of Environment ENVIRONMENTAL PROTECTION... Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30... combustion unit? (a) If your municipal waste combustion unit generates steam, you must install, calibrate...

High temperature annealing of minority carrier traps in irradiated MOCVD n(+)p InP solar cell junctions

NASA Technical Reports Server (NTRS)

Messenger, S. R.; Walters, R. J.; Summers, G. P.

1993-01-01

Deep level transient spectroscopy was used to monitor thermal annealing of trapping centers in electron irradiated n(+)p InP junctions grown by metalorganic chemical vapor deposition, at temperatures ranging from 500 up to 650K. Special emphasis is given to the behavior of the minority carrier (electron) traps EA (0.24 eV), EC (0.12 eV), and ED (0.31 eV) which have received considerably less attention than the majority carrier (hole) traps H3, H4, and H5, although this work does extend the annealing behavior of the hole traps to higher temperatures than previously reported. It is found that H5 begins to anneal above 500K and is completely removed by 630K. The electron traps begin to anneal above 540K and are reduced to about half intensity by 630K. Although they each have slightly different annealing temperatures, EA, EC, and ED are all removed by 650K. A new hole trap called H3'(0.33 eV) grows as the other traps anneal and is the only trap remaining at 650K. This annealing behavior is much different than that reported for diffused junctions.

Synergistic Trap Response of the False Stable Fly and Little House Fly (Diptera: Muscidae) to Acetic Acid and Ethanol, Two Principal Sugar Fermentation Volatiles.

PubMed

Landolt, Peter J; Cha, Dong H; Zack, Richard S

2015-10-01

In an initial observation, large numbers of muscoid flies (Diptera) were captured as nontarget insects in traps baited with solutions of acetic acid plus ethanol. In subsequent field experiments, numbers of false stable fly Muscina stabulans (Fallén) and little house fly Fannia canicularis (L.) trapped with the combination of acetic acid plus ethanol were significantly higher than those trapped with either chemical alone, or in unbaited traps. Flies were trapped with acetic acid and ethanol that had been formulated in the water of the drowning solution of the trap, or dispensed from polypropylene vials with holes in the vial lids for diffusion of evaporated chemical. Numbers of both species of fly captured were greater with acetic acid and ethanol in glass McPhail traps, compared to four other similar wet trap designs. This combination of chemicals may be useful as an inexpensive and not unpleasant lure for monitoring or removing these two pest fly species. Published by Oxford University Press on behalf of Entomological Society of America 2015. This work is written by US Government employees and is in the public domain in the US.

Building Double-decker Traps for Early Detection of Emerald Ash Borer.

PubMed

McCullough, Deborah G; Poland, Therese M

2017-10-04

Emerald ash borer (EAB) (Agrilus planipennis Fairmaire), the most destructive forest insect to have invaded North America, has killed hundreds of millions of forest and landscape ash (Fraxinus spp.) trees. Several artificial trap designs to attract and capture EAB beetles have been developed to detect, delineate, and monitor infestations. Double-decker (DD) traps consist of two corrugated plastic prisms, one green and one purple, attached to a 3 m tall polyvinyl chloride (PVC) pipe supported by a t-post. The green prism at the top of the PVC pipe is baited with cis-3-hexenol, a compound produced by ash foliage. Surfaces of both prisms are coated with sticky insect glue to capture adult EAB beetles. Double-decker traps should be placed near ash trees but in open areas, exposed to sun. Double-decker trap construction and placement are presented here, along with a summary of field experiments demonstrating the efficacy of DD traps in capturing EAB beetles. In a recent study in sites with relatively low EAB densities, double-decker traps captured significantly more EAB than green or purple prism traps or green funnel traps, all of which are designed to be suspended from a branch in the canopy of ash trees. A greater percentage of double decker traps were positive, i.e., captured at least one EAB, than the prism traps or funnel traps that were hung in ash tree canopies.

Industrially induced changes in Earth structure at the geysers geothermal area, California

USGS Publications Warehouse

Foulger, G.R.; Grant, C.C.; Ross, A.; Julian, B.R.

1997-01-01

Industrial exploitation is causing clearly-measurable changes in Earth structure at The Geysers geothermal area, California. Production at The Geysers peaked in the late 1980s at ???3.5 ?? 103 kg s-1 of steam and 1800 MW of electricity. It subsequently decreased by about 10% per year [Barker et al., 1992] because of declining reservoir pressure. The steam reservoir coincides with a strong negative anomaly (???0.16, ???9%) in the compressional-to-shear seismic wave speed ratio vP/vS, consistent with the expected effects of low-pressure vapor-phase pore fluid [Julian et al., 1996]. Between 1991 and 1994 this anomaly increased in amplitude by up to about 0.07 (???4%). This is consistent with the expected effects of continued pressure reduction and conversion of pore water to steam as a result of exploitation. These unique results show that vP/vS tomography can easily detect saturation changes caused by exploitation of reservoirs, and is a potentially valuable technique for monitoring environmental change. They also provide geophysical observational evidence that geothermal energy is not a renewable energy source.

EVALUATION OF EYE LENS DOSE TO WORKERS IN THE STEAM GENERATOR AT THE KOREAN OPTIMIZED POWER REACTOR 1000.

PubMed

Maeng, Sung Jun; Kim, Jinhwan; Cho, Gyuseong

2018-03-15

ICRP (2011) revised the dose limit to the eye lens to 20 mSv/y based on a recent epidemiological study of radiation-induced cataracts. Maintenance of steam generators at nuclear power plants is one of the highest radiation-associated tasks within a non-uniform radiation field. This study aims to evaluate eye lens doses in the steam generators of the Korean OPR1000 design. The source term was characterized based on the CRUD-specific activity, and both the eye lens dose and organ dose were simulated using MCNP6 combined with an ICRP voxel phantom and a mesh phantom, respectively. The eye lens dose was determined to be 5.39E-02-9.43E-02 Sv/h, with a negligible effect by beta particles. As the effective dose was found to be 0.81-1.21 times the lens equivalent dose depending on the phantom angles, the former can be used to estimate the lens dose in the SG of the OPR1000 for radiation monitoring purposes.

Industrially induced changes in Earth structure at the Geysers Geothermal Area, California

NASA Astrophysics Data System (ADS)

Foulger, G. R.; Grant, C. C.; Ross, A.; Julian, B. R.

Industrial exploitation is causing clearly-measurable changes in Earth structure at The Geysers geothermal area, California. Production at The Geysers peaked in the late 1980s at ˜3.5 × 10³ kg s-1 of steam and 1800 MW of electricity. It subsequently decreased by about 10% per year [Barker et al., 1992] because of declining reservoir pressure. The steam reservoir coincides with a strong negative anomaly (˜0.16, ˜9%) in the compressional-to-shear seismic wave speed ratio VP/ VS, consistent with the expected effects of low-pressure vapor-phase pore fluid [Julian et al., 1996]. Between 1991 and 1994 this anomaly increased in amplitude by up to about 0.07 (˜4%). This is consistent with the expected effects of continued pressure reduction and conversion of pore water to steam as a result of exploitation. These unique results show that VP/VS tomography can easily detect saturation changes caused by exploitation of reservoirs, and is a potentially valuable technique for monitoring environmental change. They also provide geophysical observational evidence that geothermal energy is not a renewable energy source.

Passive Baited Sequential Fly Trap

USDA-ARS?s Scientific Manuscript database

Sampling fly populations associated with human populations is needed to understand diel behavior and to monitor population densities before and after control operations. Population control measures are dependent on the results of monitoring efforts as they may provide insight into the fly behavior ...

Application of geochemical techniques to deduce the reservoir performance of the Palinpinon Geothermal Field, Philippines - an update

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramos-Candelaria, M.N.; Garcia, S.E.; Hermoso, D.Z.

1997-12-31

Regular monitoring of various geochemical parameters in the water and vapor phases of the production wells at the Palinpinon I and II sectors of the Southern Negros Geothermal Field have been useful in the identification of the dominant reservoir processes occurring related to the present exploitation strategy. Observed geochemical and physical changes in the output of production wells have dictated production and injection strategies adopted to maximize production to meet the steam requirements of the power plant. Correlation of both physical and chemical data have identified the following reservoir processes: (1) Injection breakthrough via the Ticala Fault of the highlymore » mineralized (Cl {approximately}8,000-10,500 mg/kg), isotopically enriched ({delta}{sup 18}O = -3.00{per_thousand}, {delta}{sup 2} H = -39{per_thousand}), and gas depleted brine for wells in the SW and central Puhagan. Injection breakthrough is also occurring in Palinpinon II and has resulted in temperature drops of 5-10{degrees}C.2. Pressure drawdown enhanced boiling in the liquid reservoir with steam separation of 220-240{degrees}C, feeding wells tapping the natural steam zone. However, enhanced drawdown has induced the entry of shallow acid steam condensate fluids in some wells (e.g. OK-7, PN-29D, PN-18D), which if not arrested could reduce production.« less

Steam flooding from mine workings, a viable alternative

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ayler, M.F.; Brechtel, C.

1987-05-01

The advent of steam flooding has given new life to several fields in California, substantially increasing the recoverable reserve. This process can be combined with a newly developed concept combining petroleum and mining technology. By placing mine workings 100 ft, more or less, below the bottom of the reservoir, it is possible to safely drill wells upward through the reservoir and complete them in such a way that all produced cuttings and fluids are contained within closed pipelines. Each completed well could serve as a steam injection well with continuous gravity-produced oil from the same well. As all fluids wouldmore » flow by gravity to a collection pipeline, the only needed pumps would be at the discharge within the mine shaft. Mine shafts serving the oil field could be placed in environmentally optimum sites roughly one mile apart, eliminating many of the visually objectionable disturbances. Production wells could be placed on one acre or even closer spacing, whatever good engineering dictates. Automatic controls can continuously monitor and control production from each well. Assuming one-acre well spacing, continuous steam flooding, and production from each well, a detailed analysis of anticipated mining costs indicate oil production costs under $5/bbl are possible. Even at $10/BO, a positive cash flow within two years after the start of shaft sinking is expected.« less

Determining oxide trapped charges in Al2O3 insulating films on recessed AlGaN/GaN heterostructures by gate capacitance transients measurements

NASA Astrophysics Data System (ADS)

Fiorenza, Patrick; Greco, Giuseppe; Schilirò, Emanuela; Iucolano, Ferdinando; Lo Nigro, Raffaella; Roccaforte, Fabrizio

2018-05-01

This letter presents time-dependent gate-capacitance transient measurements (C–t) to determine the oxide trapped charges (N ot) in Al2O3 films deposited on recessed AlGaN/GaN heterostructures. The C–t transients acquired at different temperatures under strong accumulation allowed to accurately monitor the gradual electron trapping, while hindering the re-emission by fast traps that may affect conventional C–V hysteresis measurements. Using this method, an increase of N ot from 2 to 6 × 1012 cm‑2 was estimated between 25 and 150 °C. The electron trapping is ruled by an Arrhenius dependence with an activation energy of 0.12 eV which was associated to points defects present in the Al2O3 films.

Comparison of Methods for Xenomonitoring in Vectors of Lymphatic Filariasis in Northeastern Tanzania

PubMed Central

Irish, Seth R.; Stevens, William M. B.; Derua, Yahya A.; Walker, Thomas; Cameron, Mary M.

2015-01-01

Monitoring Wuchereria bancrofti infection in mosquitoes (xenomonitoring) can play an important role in determining when lymphatic filariasis has been eliminated, or in focusing control efforts. As mosquito infection rates can be low, a method for collecting large numbers of mosquitoes is necessary. Gravid traps collected large numbers of Culex quinquefasciatus in Tanzania, and a collection method that targets mosquitoes that have already fed could result in increased sensitivity in detecting W. bancrofti-infected mosquitoes. The aim of this experiment was to test this hypothesis by comparing U.S. Centers for Disease Control and Prevention (CDC) light traps with CDC gravid traps in northeastern Tanzania, where Cx. quinquefasciatus is a vector of lymphatic filariasis. After an initial study where small numbers of mosquitoes were collected, a second study collected 16,316 Cx. quinquefasciatus in 60 gravid trap-nights and 240 light trap-nights. Mosquitoes were pooled and tested for presence of W. bancrofti DNA. Light and gravid traps collected similar numbers of mosquitoes per trap-night, but the physiological status of the mosquitoes was different. The estimated infection rate in mosquitoes collected in light traps was considerably higher than in mosquitoes collected in gravid traps, so light traps can be a useful tool for xenomonitoring work in Tanzania. PMID:26350454

Shot-noise-limited monitoring and phase locking of the motion of a single trapped ion.

PubMed

Bushev, P; Hétet, G; Slodička, L; Rotter, D; Wilson, M A; Schmidt-Kaler, F; Eschner, J; Blatt, R

2013-03-29

We perform a high-resolution real-time readout of the motion of a single trapped and laser-cooled Ba+ ion. By using an interferometric setup, we demonstrate a shot-noise-limited measurement of thermal oscillations with a resolution of 4 times the standard quantum limit. We apply the real-time monitoring for phase control of the ion motion through a feedback loop, suppressing the photon recoil-induced phase diffusion. Because of the spectral narrowing in the phase-locked mode, the coherent ion oscillation is measured with a resolution of about 0.3 times the standard quantum limit.

Real-time monitoring and visualization of the multi-dimensional motion of an anisotropic nanoparticle

NASA Astrophysics Data System (ADS)

Go, Gi-Hyun; Heo, Seungjin; Cho, Jong-Hoi; Yoo, Yang-Seok; Kim, Minkwan; Park, Chung-Hyun; Cho, Yong-Hoon

2017-03-01

As interest in anisotropic particles has increased in various research fields, methods of tracking such particles have become increasingly desirable. Here, we present a new and intuitive method to monitor the Brownian motion of a nanowire, which can construct and visualize multi-dimensional motion of a nanowire confined in an optical trap, using a dual particle tracking system. We measured the isolated angular fluctuations and translational motion of the nanowire in the optical trap, and determined its physical properties, such as stiffness and torque constants, depending on laser power and polarization direction. This has wide implications in nanoscience and nanotechnology with levitated anisotropic nanoparticles.

Dengue Fever Occurrence and Vector Detection by Larval Survey, Ovitrap and MosquiTRAP: A Space-Time Clusters Analysis

PubMed Central

de Melo, Diogo Portella Ornelas; Scherrer, Luciano Rios; Eiras, Álvaro Eduardo

2012-01-01

The use of vector surveillance tools for preventing dengue disease requires fine assessment of risk, in order to improve vector control activities. Nevertheless, the thresholds between vector detection and dengue fever occurrence are currently not well established. In Belo Horizonte (Minas Gerais, Brazil), dengue has been endemic for several years. From January 2007 to June 2008, the dengue vector Aedes (Stegomyia) aegypti was monitored by ovitrap, the sticky-trap MosquiTRAP™ and larval surveys in an study area in Belo Horizonte. Using a space-time scan for clusters detection implemented in SaTScan software, the vector presence recorded by the different monitoring methods was evaluated. Clusters of vectors and dengue fever were detected. It was verified that ovitrap and MosquiTRAP vector detection methods predicted dengue occurrence better than larval survey, both spatially and temporally. MosquiTRAP and ovitrap presented similar results of space-time intersections to dengue fever clusters. Nevertheless ovitrap clusters presented longer duration periods than MosquiTRAP ones, less acuratelly signalizing the dengue risk areas, since the detection of vector clusters during most of the study period was not necessarily correlated to dengue fever occurrence. It was verified that ovitrap clusters occurred more than 200 days (values ranged from 97.0±35.35 to 283.0±168.4 days) before dengue fever clusters, whereas MosquiTRAP clusters preceded dengue fever clusters by approximately 80 days (values ranged from 65.5±58.7 to 94.0±14. 3 days), the former showing to be more temporally precise. Thus, in the present cluster analysis study MosquiTRAP presented superior results for signaling dengue transmission risks both geographically and temporally. Since early detection is crucial for planning and deploying effective preventions, MosquiTRAP showed to be a reliable tool and this method provides groundwork for the development of even more precise tools. PMID:22848729

Effectiveness of odor-baited trap trees for plum curculio (Coleoptera: Curculionidae) monitoring in commercial apple orchards in the northeast.

PubMed

Piñero, Jaime C; Agnello, Arthur M; Tuttle, Arthur; Leskey, Tracy C; Faubert, Heather; Koehler, Glen; Los, Lorraine; Morin, Glenn; Leahy, Kathleen; Cooley, Daniel R; Prokopy, Ronald J

2011-10-01

The plum curculio, Conotrachelus nenuphar (Herbst), is a key pest of pome and stone fruit in eastern and central North America. For effective management of this insect pest in commercial apple (Malus spp.) orchards in the northeastern United States and Canada, one of the greatest challenges has been to determine the need for and timing of insecticide applications that will protect apple fruit from injury by adults. In a 2004-2005 study, we assessed the efficacy and economic viability of a reduced-risk integrated pest management strategy involving an odor-baited trap tree approach to determine need for and timing of insecticide use against plum curculio based on appearance of fresh egg-laying scars. Evaluations took place in commercial apple orchards in seven northeastern U.S. states. More specifically, we compared the trap-tree approach with three calendar-driven whole-block sprays and with heat-unit accumulation models that predict how long insecticide should be applied to orchard trees to prevent injury by plum curculio late in the season. Trap tree plots received a whole-plot insecticide spray by the time of petal fall, and succeeding sprays (if needed) were applied to peripheral-row trees only, depending on a threshold of one fresh plum curculio egg-laying scar out of 25 fruit sampled from a single trap tree. In both years, level of plum curculio injury to fruit sampled from perimeter-row, the most interior-row trees and whole-plot injury in trap tree plots did not differ significantly from that recorded in plots subject to conventional management or in plots managed using the heat-unit accumulation approach. The amount of insecticide used in trap tree plots was reduced at least by 43% compared with plots managed with the conventional approach. Advantages and potential pitfalls of the bio-based trap tree approach to plum curculio monitoring in apple orchards are discussed.

Development of behaviorally based monitoring tools for the brown marmorated stink bug, Halyomorpha Halys (Stal) (Heteroptera: Pentatomidae) in commercial tree fruit orchards

USDA-ARS?s Scientific Manuscript database

We found that captures of the invasive brown marmorated stink bug, Halyomorpha halys (Stal), were significantly greater in pyramid traps baited with the known attractant, methyl (2E,4E,6Z)-decatrienoate, compared with unbaited traps. A dose-dependent response by adults to lures formulated with incr...

Ethanol and (–)-α-pinene for detecting and monitoring bark and ambrosia beetles in the southeastern USA

Treesearch

Daniel R. Miller; Robert J. Rabaglia; Christopher M. Crowe

2011-01-01

Our objective was to verify the need for separate traps baited with ethanol or ethanol and (–)-α-pinene for bark and ambrosia beetles in pine stands of the southeastern U.S. Eight trapping experiments were conducted in stands of mature pine in Alabama, Florida, Georgia, North Carolina, and South Carolina.

Detection of and Monitoring for Aedes albopictus (Diptera: Culicidae) in Suburban and Sylvatic Habitats in North Central Florida using Four Sampling Techniques

USDA-ARS?s Scientific Manuscript database

A sampling study using a BG-Sentinel trap baited with CO2, a gravid trap baited with an oak-pine infusion, a human subject and a vegetative aspirator was conducted to compare their reliability at detecting Ae. albopictus in suburban and sylvatic habitats. We collected 73,849 mosquitoes, representin...

Comparative evaluation of the efficiency of the BG-Sentinel trap, CDC light trap and Mosquito-oviposition trap for the surveillance of vector mosquitoes.

PubMed

Li, Yiji; Su, Xinghua; Zhou, Guofa; Zhang, Hong; Puthiyakunnon, Santhosh; Shuai, Shufen; Cai, Songwu; Gu, Jinbao; Zhou, Xiaohong; Yan, Guiyun; Chen, Xiao-Guang

2016-08-12

The surveillance of vector mosquitoes is important for the control of mosquito-borne diseases. To identify a suitable surveillance tool for the adult dengue vector Aedes albopictus, the efficacy of the BG-Sentinel trap, CDC light trap and Mosquito-oviposition trap (MOT) on the capture of vector mosquitoes were comparatively evaluated in this study. The capture efficiencies of the BG-Sentinel trap, CDC light trap and Mosquito-oviposition trap for common vector mosquitoes were tested in a laboratory setting, through the release-recapture method, and at two field sites of Guangzhou, China from June 2013 to May 2014. The captured mosquitoes were counted, species identified and compared among the three traps on the basis of species. In the release-recapture experiments in a laboratory setting, the BG-Sentinel trap caught significantly more Aedes albopictus and Culex quinquefasciatus than the CDC light trap and Mosquito-ovitrap, except for Anopheles sinensis. The BG-Sentinel trap had a higher efficacy in capturing female rather than male Ae. albopictus and Cx. quinquefasciatus, but the capture in CDC light traps displayed no significant differences. In the field trial, BG-Sentinel traps collected more Aedes albopictus than CDC light traps and MOTs collected in both urban and suburban areas. The BG-Sentinel trap was more sensitive for monitoring the population density of Aedes albopictus than the CDC light trap and MOT during the peak months of the year 2013. However, on an average, CDC light traps captured significantly more Cx. quinquefasciatus than BG-Sentinel traps. The population dynamics of Cx. quinquefasciatus displayed a significant seasonal variation, with the lowest numbers in the middle of the year. This study indicates that the BG-Sentinel trap is more effective than the commonly used CDC light trap and MOT in sampling adult Aedes albopictus and Culex quinquefasciatus. We recommend its use in the surveillance of dengue vector mosquitoes in China.

Monitoring Aethina tumida (Coleoptera: Nitidulidae) with baited bottom board traps: occurrence and seasonal abundance in honey bee colonies in Kenya.

PubMed

Torto, Baldwyn; Fombong, Ayuka T; Arbogast, Richard T; Teal, Peter E A

2010-12-01

The population dynamics of the honey bee pest Aethina tumida Murray (small hive beetle) have been studied in the United States with flight and Langstroth hive bottom board traps baited with pollen dough inoculated with a yeast Kodamaea ohmeri associated with the beetle. However, little is known about the population dynamics of the beetle in its native host range. Similarly baited Langstroth hive bottom board traps were used to monitor the occurrence and seasonal abundance of the beetle in honey bee colonies at two beekeeping locations in Kenya. Trap captures indicated that the beetle was present in honey bee colonies in low numbers all year round, but it was most abundant during the rainy season, with over 80% trapped during this period. The survival of larvae was tested in field releases under dry and wet soil conditions, and predators of larvae were identified. The actvity and survival of the beetle were strongly influenced by a combination of abiotic and biotic factors. Larval survival was higher during wet (28%) than dry (1.1%) conditions, with pupation occurring mostly at 0-15 cm and 11-20 cm, respectively, beneath the surface soil during these periods. The ant Pheidole megacephala was identified as a key predator of larvae at this site, and more active during the dry than wet seasons. These observations imply that intensive trapping during the rainy season could reduce the population of beetles infesting hives in subsequent seasons especially in places where the beetle is a serious pest. © 2010 Entomological Society of America

An ex situ evaluation of TBA- and MTBE-baited bio-traps

PubMed Central

North, Katharine P.; Mackay, Douglas M.; Annable, Michael D.; Sublette, Kerry L.; Davis, Greg; Holland, Reef B.; Petersen, Daniel; Scow, Kate M.

2013-01-01

Aquifer microbial communities can be investigated using Bio-traps® (“bio-traps”), passive samplers containing Bio-Sep® beads (“bio-beads”) that are deployed in monitoring wells to be colonized by bacteria delivered via groundwater flow through the well. When bio-beads are “baited” with organic contaminants enriched in 13C, stable isotope probing allows assessment of the composition and activity of the microbial community. This study used an ex situ system fed by groundwater continuously extracted from an adjacent monitoring well within an experimentally-created aerobic zone treating a tert-butyl alcohol (TBA) plume. The goal was to evaluate aspects of bio-trap performance that cannot be studied quantitatively in situ. The measured groundwater flow through a bio-trap housing suggests that such traps might typically “sample” about 1.8 L per month. The desorption of TBA or methyl tert-butyl ether (MTBE) bait from bio-traps during a typical deployment duration of 6 weeks was approximately 90% and 45%, respectively, of the total initial bait load, with initially high rate of mass loss that decreased markedly after a few days. The concentration of TBA in groundwater flowing by the TBA-baited bio-beads was estimated to be as high as 3400 mg/L during the first few days, which would be expected to inhibit growth of TBA-degrading microbes. Initial inhibition was also implied for the MTBE-baited bio-trap, but at lower concentrations and for a shorter time. After a few days, concentrations in groundwater flowing through the bio-traps dropped below inhibitory concentrations but remained 4–5 orders of magnitude higher than TBA or MTBE concentrations within the aquifer at the experimental site. Desorption from the bio-beads during ex situ deployment occurred at first as predicted by prior sorption analyses of bio-beads but with apparent hysteresis thereafter, possibly due to mass transfer limitations caused by colonizing microbes. These results suggest that TBA- or MTBE-baited bio-traps could be baited at lower initial total mass loading with no detriment to trapping ability. The bio-traps were able to collect detectable amounts of microbial DNA and thus allow some insight into the sparse microbial community present in the aquifer during remediation of the low concentration plume. PMID:22621895

Failure of non-vacuum steam sterilization processes for dental handpieces.

PubMed

Winter, S; Smith, A; Lappin, D; McDonagh, G; Kirk, B

2017-12-01

Dental handpieces are used in critical and semi-critical operative interventions. Although some dental professional bodies recommend that dental handpieces are sterilized between patient use there is a lack of clarity and understanding of the effectiveness of different steam sterilization processes. The internal mechanisms of dental handpieces contain narrow lumens (0.8-2.3 mm) which can impede the removal of air and ingress of saturated steam required to achieve sterilization conditions. To identify the extent of sterilization failure in dental handpieces using a non-vacuum process. In-vitro and in-vivo investigations were conducted on widely used UK bench-top steam sterilizers and three different types of dental handpieces. The sterilization process was monitored inside the lumens of dental handpieces using thermometric (TM; dataloggers), chemical indicator (CI), and biological indicator (BI) methods. All three methods of assessing achievement of sterility within dental handpieces that had been exposed to non-vacuum sterilization conditions demonstrated a significant number of failures [CI: 8/3024 (fails/no. of tests); BI: 15/3024; TM: 56/56] compared to vacuum sterilization conditions (CI: 2/1944; BI: 0/1944; TM: 0/36). The dental handpiece most likely to fail sterilization in the non-vacuum process was the surgical handpiece. Non-vacuum sterilizers located in general dental practice had a higher rate of sterilization failure (CI: 25/1620; BI: 32/1620; TM: 56/56) with no failures in vacuum process. Non-vacuum downward/gravity displacement, type N steam sterilizers are an unreliable method for sterilization of dental handpieces in general dental practice. The handpiece most likely to fail sterilization is the type most frequently used for surgical interventions. Copyright © 2017 The Healthcare Infection Society. Published by Elsevier Ltd. All rights reserved.

Effect of Environment on the Stress- Rupture Behavior of a C/SiC Composite Studied

NASA Technical Reports Server (NTRS)

Verrilli, Michael J.; Kiser, J. Douglas; Opila, Elizabeth J.; Calomino, Anthony M.

2002-01-01

Advanced reusable launch vehicles will likely incorporate fiber-reinforced ceramic matrix composites (CMC's) in critical propulsion and airframe components. The use of CMC's is highly desirable to save weight, improve reuse capability, and increase performance. One of the candidate CMC materials is carbon-fiber-reinforced silicon carbide (C/SiC). In potential propulsion applications, such as turbopump rotors and nozzle exit ramps, C/SiC components will be subjected to a service cycle that includes mechanical loading under complex, high-pressure environments containing hydrogen, oxygen, and steam. Degradation of both the C fibers and the SiC matrix are possible in these environments. The objective of this effort was to evaluate the mechanical behavior of C/SiC in various environments relevant to reusable launch vehicle applications. Stress-rupture testing was conducted at the NASA Glenn Research Center on C/SiC specimens in air and steam-containing environments. Also, the oxidation kinetics of the carbon fibers that reinforce the composite were monitored by thermogravimetric analysis in the same environments and temperatures used for the stress-rupture tests of the C/SiC composite specimens. The stress-rupture lives obtained for C/SiC tested in air and in steam/argon mixtures are shown in the following bar chart. As is typical for most materials, lives obtained at the lower temperature (600 C) are longer than for the higher temperature (1200 C). The effect of environment was most pronounced at the lower temperature, where the average test duration in steam at 600 C was at least 30 times longer than the lives obtained in air. The 1200 C data revealed little difference between the lives of specimens tested in air and steam at atmospheric pressure.

Monitoring tigers with confidence.

PubMed

Linkie, Matthew; Guillera-Arroita, Gurutzeta; Smith, Joseph; Rayan, D Mark

2010-12-01

With only 5% of the world's wild tigers (Panthera tigris Linnaeus, 1758) remaining since the last century, conservationists urgently need to know whether or not the management strategies currently being employed are effectively protecting these tigers. This knowledge is contingent on the ability to reliably monitor tiger populations, or subsets, over space and time. In the this paper, we focus on the 2 seminal methodologies (camera trap and occupancy surveys) that have enabled the monitoring of tiger populations with greater confidence. Specifically, we: (i) describe their statistical theory and application in the field; (ii) discuss issues associated with their survey designs and state variable modeling; and, (iii) discuss their future directions. These methods have had an unprecedented influence on increasing statistical rigor within tiger surveys and, also, surveys of other carnivore species. Nevertheless, only 2 published camera trap studies have gone beyond single baseline assessments and actually monitored population trends. For low density tiger populations (e.g. <1 adult tiger/100 km(2)) obtaining sufficient precision for state variable estimates from camera trapping remains a challenge because of insufficient detection probabilities and/or sample sizes. Occupancy surveys have overcome this problem by redefining the sampling unit (e.g. grid cells and not individual tigers). Current research is focusing on developing spatially explicit capture-mark-recapture models and estimating abundance indices from landscape-scale occupancy surveys, as well as the use of genetic information for identifying and monitoring tigers. The widespread application of these monitoring methods in the field now enables complementary studies on the impact of the different threats to tiger populations and their response to varying management intervention. © 2010 ISZS, Blackwell Publishing and IOZ/CAS.

Encapsulated Essential Oils as an Alternative to Insecticides in Funnel Traps.

PubMed

Pascual-Villalobos, M J; López, M D; Castañé, C; Soler, A; Riudavets, J

2015-08-01

Pheromone-lured funnel traps are widely used for pest monitoring and mass trapping in agricultural fields and stores. DDVP vapona (dichlorvos), the insecticide of choice as a killing agent inside traps, has been banned, and research on new products is being pursued. Essential oils (EO) could be an alternative if properly formulated. To test their potential, beads of encapsulated coriander and basil EO were tested in funnel traps in stores of almonds and pet foods during 2 mo. The number of adult moth (Plodia interpunctella (Hübner) and Ephestia kuehniella Zeller) dead captures was similar with either coriander or basil EO beads and with vapona tablets while there were more insects alive in the control. These preliminary results indicate a good potential for the development of such natural products as an alternative to synthetic insecticides to include them inside funnel traps. © The Authors 2015. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

40 CFR 63.10011 - How do I demonstrate initial compliance with the emissions limits and work practice standards?

Code of Federal Regulations, 2013 CFR

2013-07-01

... Hazardous Air Pollutants: Coal- and Oil-Fired Electric Utility Steam Generating Units Testing and Initial... liquid oil-fired unit, and you use quarterly stack testing for HCl and HF plus site-specific parameter monitoring to demonstrate continuous performance, you must also establish a site-specific operating limit, in...

40 CFR 63.10011 - How do I demonstrate initial compliance with the emissions limits and work practice standards?

Code of Federal Regulations, 2014 CFR

2014-07-01

... Hazardous Air Pollutants: Coal- and Oil-Fired Electric Utility Steam Generating Units Testing and Initial... liquid oil-fired unit, and you use quarterly stack testing for HCl and HF plus site-specific parameter monitoring to demonstrate continuous performance, you must also establish a site-specific operating limit, in...

40 CFR 62.15265 - How do I monitor the load of my municipal waste combustion unit?

Code of Federal Regulations, 2013 CFR

2013-07-01

... Mechanical Engineers (ASME PTC 4.1—1964): Test Code for Steam Generating Units, Power Test Code 4.1-1964... of Mechanical Engineers, Service Center, 22 Law Drive, Post Office Box 2900, Fairfield, NJ 07007. You....archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. (4) Design, construct...

40 CFR 62.15265 - How do I monitor the load of my municipal waste combustion unit?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Mechanical Engineers (ASME PTC 4.1—1964): Test Code for Steam Generating Units, Power Test Code 4.1-1964... of Mechanical Engineers, Service Center, 22 Law Drive, Post Office Box 2900, Fairfield, NJ 07007. You....archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. (4) Design, construct...

40 CFR 62.15265 - How do I monitor the load of my municipal waste combustion unit?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Mechanical Engineers (ASME PTC 4.1—1964): Test Code for Steam Generating Units, Power Test Code 4.1-1964... of Mechanical Engineers, Service Center, 22 Law Drive, Post Office Box 2900, Fairfield, NJ 07007. You....archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. (4) Design, construct...

40 CFR 62.15265 - How do I monitor the load of my municipal waste combustion unit?

Code of Federal Regulations, 2012 CFR

2012-07-01

... Mechanical Engineers (ASME PTC 4.1—1964): Test Code for Steam Generating Units, Power Test Code 4.1-1964... of Mechanical Engineers, Service Center, 22 Law Drive, Post Office Box 2900, Fairfield, NJ 07007. You....archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. (4) Design, construct...

40 CFR 62.15265 - How do I monitor the load of my municipal waste combustion unit?

Code of Federal Regulations, 2014 CFR

2014-07-01

... Mechanical Engineers (ASME PTC 4.1—1964): Test Code for Steam Generating Units, Power Test Code 4.1-1964... of Mechanical Engineers, Service Center, 22 Law Drive, Post Office Box 2900, Fairfield, NJ 07007. You....archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. (4) Design, construct...

40 CFR Table 7 to Subpart U of... - Operating Parameters for Which Monitoring Levels Are Required To Be Established for Continuous...

Code of Federal Regulations, 2012 CFR

2012-07-01

.... Condenser Exit temperature Maximum temperature. Carbon adsorber Total regeneration steam flow or nitrogen flow, or pressure (gauge or absolute) a during carbon bed regeneration cycle; and temperature of the carbon bed after regeneration (and within 15 minutes of completing any cooling cycle(s)) Maximum flow or...

40 CFR Table 7 to Subpart U of... - Operating Parameters for Which Monitoring Levels Are Required To Be Established for Continuous...

Code of Federal Regulations, 2014 CFR

2014-07-01

.... Condenser Exit temperature Maximum temperature. Carbon adsorber Total regeneration steam flow or nitrogen flow, or pressure (gauge or absolute) a during carbon bed regeneration cycle; and temperature of the carbon bed after regeneration (and within 15 minutes of completing any cooling cycle(s)) Maximum flow or...

40 CFR Table 7 to Subpart U of... - Operating Parameters for Which Monitoring Levels Are Required To Be Established for Continuous...

Code of Federal Regulations, 2010 CFR

2010-07-01

.... Condenser Exit temperature Maximum temperature. Carbon adsorber Total regeneration steam flow or nitrogen flow, or pressure (gauge or absolute) a during carbon bed regeneration cycle; and temperature of the carbon bed after regeneration (and within 15 minutes of completing any cooling cycle(s)) Maximum flow or...

40 CFR Table 7 to Subpart U of... - Operating Parameters for Which Monitoring Levels Are Required To Be Established for Continuous...

Code of Federal Regulations, 2011 CFR

2011-07-01

.... Condenser Exit temperature Maximum temperature. Carbon adsorber Total regeneration steam flow or nitrogen flow, or pressure (gauge or absolute) a during carbon bed regeneration cycle; and temperature of the carbon bed after regeneration (and within 15 minutes of completing any cooling cycle(s)) Maximum flow or...

40 CFR Table 7 to Subpart U of... - Operating Parameters for Which Monitoring Levels Are Required To Be Established for Continuous...

Code of Federal Regulations, 2013 CFR

2013-07-01

.... Condenser Exit temperature Maximum temperature. Carbon adsorber Total regeneration steam flow or nitrogen flow, or pressure (gauge or absolute) a during carbon bed regeneration cycle; and temperature of the carbon bed after regeneration (and within 15 minutes of completing any cooling cycle(s)) Maximum flow or...

40 CFR 63.143 - Process wastewater provisions-inspections and monitoring of operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... separator that receives, manages, or treats a Group 1 wastewater stream, a residual removed from a Group 1 wastewater stream, a recycled Group 1 wastewater stream, or a recycled residual removed from a Group 1... of this subpart. (b) For each design steam stripper and biological treatment unit used to comply with...

Optical pumping of deep traps in AlGaN/GaN-on-Si HEMTs using an on-chip Schottky-on-heterojunction light-emitting diode

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Baikui; Tang, Xi; Chen, Kevin J., E-mail: eekjchen@ust.hk

2015-03-02

In this work, by using an on-chip integrated Schottky-on-heterojunction light-emitting diode (SoH-LED) which is seamlessly integrated with the AlGaN/GaN high electron mobility transistor (HEMT), we studied the effect of on-chip light illumination on the de-trapping processes of electrons from both surface and bulk traps. Surface trapping was generated by applying OFF-state drain bias stress, while bulk trapping was generated by applying positive substrate bias stress. The de-trapping processes of surface and/or bulk traps were monitored by measuring the recovery of dynamic on-resistance R{sub on} and/or threshold voltage V{sub th} of the HEMT. The results show that the recovery processes ofmore » both dynamic R{sub on} and threshold voltage V{sub th} of the HEMT can be accelerated by the on-chip SoH-LED light illumination, demonstrating the potentiality of on-chip hybrid opto-HEMTs to minimize the influences of traps during dynamic operation of AlGaN/GaN power HEMTs.« less

Cycle chemistry monitoring system as means of improving the reliability of the equipment at the power plants

NASA Astrophysics Data System (ADS)

Yegoshina, O. V.; Voronov, V. N.; Yarovoy, V. O.; Bolshakova, N. A.

2017-11-01

There are many problems in domestic energy at the present that require urgent solutions in the near future. One of these problems - the aging of the main and auxiliary equipment. Wear of equipment is the cause of decrease reliability and efficiency of power plants. Reliability of the equipment are associated with the introduction of cycle chemistry monitoring system. The most damageable equipment’s are boilers (52.2 %), turbines (12.6 %) and heating systems (12.3 %) according to the review of failure rate on the power plants. The most part of the damageability of the boiler is heated surfaces (73.2 %). According to the Russian technical requirements, the monitoring systems are responsible to reduce damageability the boiler heating surfaces and to increase the reliability of the equipment. All power units capacity of over 50 MW are equipped with cycle chemistry monitoring systems in order to maintain water chemistry within operating limits. The main idea of cycle chemistry monitoring systems is to improve water chemistry at power plants. According to the guidelines, cycle chemistry monitoring systems of a single unit depends on its type (drum or once-through boiler) and consists of: 20…50 parameters of on-line chemical analyzers; 20…30 «grab» sample analyses (daily) and about 15…20 on-line monitored operating parameters. The operator of modern power plant uses with many data at different points of steam/water cycle. Operators do not can estimate quality of the cycle chemistry due to the large volume of daily and every shift information and dispersion of data, lack of systematization. In this paper, an algorithm for calculating the quality index developed for improving control the water chemistry of the condensate, feed water and prevent scaling and corrosion in the steam/water cycle.

Rock Island Dam Smolt Monitoring; 1994-1995 Annual Report.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Truscott, Keith B.; Fielder, Paul C.

1995-10-01

Downstream migrating salmon and steelhead trout (Oncorhynchus spp.) smolts were monitored at the Rock Island Dam bypass trap from April 1 - August 31, 1954. This was the tenth consecutive year that the bypass trap was monitored. Data collected included: (1) number of fish caught by species, (2) number of adipose clipped and/or Passive Integrated Transponder (PIT) tagged fish caught by species, (3) daily average riverflow, (4) daily average powerhouse No. 1 and No. 2 flows and daily average spill. These data were transmitted to the Fish Passage Center, which manages the Smolt Monitoring Program throughout the Columbia River Basin.more » The Smolt Monitoring Program is used to manage the {open_quotes}water budget{close_quotes}, releasing upstream reservoir water storage allocated to supplement river flows to enhance survival of downstream migrating juvenile salmonids. The Rock Island Dam trapping facility collected 37,795 downstream migrating salmonids in 1994. Collected fish included 4 yearling and 4 sub-yearling chinook salmon (O. tshawytscha) that had been previously PIT tagged to help determine migration rates. Additionally, 1,132 sub-yearling chinook, 4,185 yearling chinook, 6,627 steelhead, (O. mykiss) and 422 sockeye (O. nerka) with clipped adipose fins were collected. The middle 80% of the 1994 spring migration (excluding sub-yearling chinooks) passed Rock Island Dam during a 34 day period, April 25 - May 28. Passage rates of chinook and steelhead smolts released from hatcheries and the downstream migration timing of all salmonids are presented. The spring migration timing of juvenile salmonids is strongly influenced by hatchery releases above Rock Island Dam.« less

System for particle concentration and detection

DOEpatents

Morales, Alfredo M.; Whaley, Josh A.; Zimmerman, Mark D.; Renzi, Ronald F.; Tran, Huu M.; Maurer, Scott M.; Munslow, William D.

2013-03-19

A new microfluidic system comprising an automated prototype insulator-based dielectrophoresis (iDEP) triggering microfluidic device for pathogen monitoring that can eventually be run outside the laboratory in a real world environment has been used to demonstrate the feasibility of automated trapping and detection of particles. The system broadly comprised an aerosol collector for collecting air-borne particles, an iDEP chip within which to temporarily trap the collected particles and a laser and fluorescence detector with which to induce a fluorescence signal and detect a change in that signal as particles are trapped within the iDEP chip.

Investigating Trapped Particle Asymmetry Modes and Temperature Effects in the Lawrence Non-neutral Torus II

NASA Astrophysics Data System (ADS)

Nirwan, R.; Swanson, P.; Stoneking, M. R.

2017-10-01

Electron plasma is confined in the Lawrence Non-Neutral Torus II using a purely toroidal magnetic field (R0 = 18 cm, B < 1 kG) for confinement times exceeding 1 second. The LNT II can be configured for fully toroidal traps or variable-length partial toroidal traps. The behavior of the plasma is observed by monitoring the image charge on isolated wall sectors. The plasma is excited by application of a sinusoidal tone burst to selected wall sectors. Phase-space separatrices are introduced by applying squeeze potentials to toroidally localized, but poloidally continuous sectors and the resulting interaction between trapped and passing particles populations results in asymmetry modes and transport. These experiments provide a comparison with similar experiments in cylindrical traps. We also report on the development of temperature measurement techniques and assess temperature affects on diocotron and asymmetry modes. This work is supported by National Science Foundation Grant No. PHY-1202540.

Mini ion trap mass spectrometer

DOEpatents

Dietrich, Daniel D.; Keville, Robert F.

1995-01-01

An ion trap which operates in the regime between research ion traps which can detect ions with a mass resolution of better than 1:10.sup.9 and commercial mass spectrometers requiring 10.sup.4 ions with resolutions of a few hundred. The power consumption is kept to a minimum by the use of permanent magnets and a novel electron gun design. By Fourier analyzing the ion cyclotron resonance signals induced in the trap electrodes, a complete mass spectra in a single combined structure can be detected. An attribute of the ion trap mass spectrometer is that overall system size is drastically reduced due to combining a unique electron source and mass analyzer/detector in a single device. This enables portable low power mass spectrometers for the detection of environmental pollutants or illicit substances, as well as sensors for on board diagnostics to monitor engine performance or for active feedback in any process involving exhausting waste products.

Mini ion trap mass spectrometer

DOEpatents

Dietrich, D.D.; Keville, R.F.

1995-09-19

An ion trap is described which operates in the regime between research ion traps which can detect ions with a mass resolution of better than 1:10{sup 9} and commercial mass spectrometers requiring 10{sup 4} ions with resolutions of a few hundred. The power consumption is kept to a minimum by the use of permanent magnets and a novel electron gun design. By Fourier analyzing the ion cyclotron resonance signals induced in the trap electrodes, a complete mass spectra in a single combined structure can be detected. An attribute of the ion trap mass spectrometer is that overall system size is drastically reduced due to combining a unique electron source and mass analyzer/detector in a single device. This enables portable low power mass spectrometers for the detection of environmental pollutants or illicit substances, as well as sensors for on board diagnostics to monitor engine performance or for active feedback in any process involving exhausting waste products. 10 figs.

Electron source for a mini ion trap mass spectrometer

DOEpatents

Dietrich, Daniel D.; Keville, Robert F.

1995-01-01

An ion trap which operates in the regime between research ion traps which can detect ions with a mass resolution of better than 1:10.sup.9 and commercial mass spectrometers requiring 10.sup.4 ions with resolutions of a few hundred. The power consumption is kept to a minimum by the use of permanent magnets and a novel electron gun design. By Fourier analyzing the ion cyclotron resonance signals induced in the trap electrodes, a complete mass spectra in a single combined structure can be detected. An attribute of the ion trap mass spectrometer is that overall system size is drastically reduced due to combining a unique electron source and mass analyzer/detector in a single device. This enables portable low power mass spectrometers for the detection of environmental pollutants or illicit substances, as well as sensors for on board diagnostics to monitor engine performance or for active feedback in any process involving exhausting waste products.

Cell Deformation by Single-beam Acoustic Trapping: A Promising Tool for Measurements of Cell Mechanics

PubMed Central

Hwang, Jae Youn; Kim, Jihun; Park, Jin Man; Lee, Changyang; Jung, Hayong; Lee, Jungwoo; Shung, K. Kirk

2016-01-01

We demonstrate a noncontact single-beam acoustic trapping method for the quantification of the mechanical properties of a single suspended cell with label-free. Experimentally results show that the single-beam acoustic trapping force results in morphological deformation of a trapped cell. While a cancer cell was trapped in an acoustic beam focus, the morphological changes of the immobilized cell were monitored using bright-field imaging. The cell deformability was then compared with that of a trapped polystyrene microbead as a function of the applied acoustic pressure for a better understanding of the relationship between the pressure and degree of cell deformation. Cell deformation was found to become more pronounced as higher pressure levels were applied. Furthermore, to determine if this acoustic trapping method can be exploited in quantifying the cell mechanics in a suspension and in a non-contact manner, the deformability levels of breast cancer cells with different degrees of invasiveness due to acoustic trapping were compared. It was found that highly-invasive breast cancer cells exhibited greater deformability than weakly-invasive breast cancer cells. These results clearly demonstrate that the single-beam acoustic trapping technique is a promising tool for non-contact quantitative assessments of the mechanical properties of single cells in suspensions with label-free. PMID:27273365

Evaluation of collection methods for Culex quinquefasciatus, Aedes aegypti, and Aedes simpsoni in northeastern Tanzania.

PubMed

Thornton, Jonathan Harold; Batengana, Bernard Malongo; Eiras, Alvaro Eduardo; Irish, Seth Robert

2016-12-01

In East Africa, significant morbidity and mortality are caused by infections spread by Culex quinquefasciatus and Aedes aegypti. Sticky traps have been shown to be effective tools for sampling populations of Aedes mosquitoes and have been found to catch Cx. quinquefasciatus. Thus, they could potentially be used to sample populations of this species. This study compared Sticky ovitraps (SO) and MosquiTraps (MQT) with the CDC Gravid trap (CDC-GT) for collection of Culex and Aedes mosquito populations in Tanzania. A follow-up experiment was carried out using traps set for a 24-h period to accommodate the oviposition habits of Aedes aegypti and Ae. simpsoni s.l. mosquitoes. The results showed that the CDC-GT caught significantly more Cx. quinquefasciatus and Ae. aegypti than the SO or MQT, but there was no significant difference in the number of mosquitoes caught between the two sticky traps or of Ae. simpsoni s.l. caught among the three trap types. The results suggest that CDC-GTs are the most appropriate in sampling of Cx. quinquefasciatus. Although CDC-GTs collected more Ae. aegypti than the sticky traps, the simplicity and cost benefit of sticky traps facilitates large scale studies. All three trap types should be considered for monitoring Aedes mosquitoes. © 2016 The Society for Vector Ecology.

Trapper readies trap for lizard

NASA Technical Reports Server (NTRS)

2000-01-01

State-licensed animal trapper James Dean sets the open door of an animal trap on KSC. He hopes to catch a large monitor lizard spotted recently near S.R. 3, a route into the Center, by several area residents. The lizard is not a native of the area, and possibly a released pet. Dean is working with the cooperation of KSC and the Merritt Island National Wildlife Refuge.

Filter for on-line air monitor unaffected by radon progeny and method of using same

DOEpatents

Phillips, Terrance D.; Edwards, Howard D.

1999-01-01

An apparatus for testing air having contaminants and radon progeny therein. The apparatus includes a sampling box having an inlet for receiving the air and an outlet for discharging the air. The sampling box includes a filter made of a plate of sintered stainless steel. The filter traps the contaminants, yet allows at least a portion of the radon progeny to pass therethrough. A method of testing air having contaminants and radon progeny therein. The method includes providing a testing apparatus that has a sampling box with an inlet for receiving the air and an outlet for discharging the air, and has a sintered stainless steel filter disposed within said sampling box; drawing air from a source into the sampling box using a vacuum pump; passing the air through the filter; monitoring the contaminants trapped by the filter; and providing an alarm when a selected level of contaminants is reached. The filter traps the contaminants, yet allows at least a portion of the radon progeny to pass therethrough.

First report of Zaprionus indianus (Diptera: Drosophilidae) in commercial fruits and vegetables in Pennsylvania.

PubMed

Joshi, Neelendra K; Biddinger, David J; Demchak, Kathleen; Deppen, Alan

2014-01-01

Zaprionus indianus (Gupta) (Diptera: Drosophilidae), an invasive vinegar fly, was found for the first time in Adams County, Pennsylvania, in 2011. It was found in a commercial tart cherry orchard using apple cider vinegar (ACV) traps that were monitoring another invasive vinegar fly, the spotted wing drosophila, Drosophila suzukii (Matsumura) (Diptera: Drosophilidae). Coincidentally, the first record of D. suzukii found in Pennsylvania was also found in this same cherry orchard only 3 months earlier as part of a spotted wing drosophila survey effort in raspberry, blackberry, grape, and tart cherry in Adams County. These same crops plus blueberry and tomato were monitored again in 2012. In this article, adult Z. indianus captures in ACV traps and other traps deployed in the aforementioned crops during 2012 season are presented and the economic importance of Z. indianus is discussed. © The Author 2014. Published by Oxford University Press on behalf of the Entomological Society of America.

Superoxide Anion Radical Production in the Tardigrade Paramacrobiotus richtersi, the First Electron Paramagnetic Resonance Spin-Trapping Study.

PubMed

Savic, Aleksandar G; Guidetti, Roberto; Turi, Ana; Pavicevic, Aleksandra; Giovannini, Ilaria; Rebecchi, Lorena; Mojovic, Milos

2015-01-01

Anhydrobiosis is an adaptive strategy that allows withstanding almost complete body water loss. It has been developed independently by many organisms belonging to different evolutionary lines, including tardigrades. The loss of water during anhydrobiotic processes leads to oxidative stress. To date, the metabolism of free radicals in tardigrades remained unclear. We present a method for in vivo monitoring of free radical production in tardigrades, based on electron paramagnetic resonance and spin-trap DEPMPO, which provides simultaneous identification of various spin adducts (i.e., different types of free radicals). The spin trap can be easily absorbed in animals, and tardigrades stay alive during the measurements and during 24-h monitoring after the treatment. The results show that hydrated specimens of the tardigrade Paramacrobiotus richtersi produce the pure superoxide anion radical ((•)O2(-)). This is an unexpected result, as all previously examined animals and plants produce both superoxide anion radical and hydroxyl radical ((•)OH) or exclusively hydroxyl radical.

Evaluation of funnel traps for characterizing the bark beetle (Coleoptera: Scolytidae) communities in ponderosa pine forests of north-central Arizona.

PubMed

Hayes, Christopher J; DeGomez, Tom E; Clancy, Karen M; Williams, Kelly K; McMillin, Joel D; Anhold, John A

2008-08-01

Lindgren funnel traps baited with aggregation pheromones are widely used to monitor and manage populations of economically important bark beetles (Coleoptera: Scolytidae). This study was designed to advance our understanding of how funnel trap catches assess bark beetle communities and relative abundance of individual species. In the second year (2005) of a 3-yr study of the bark beetle community structure in north-central Arizona pine (Pinus spp.) forests, we collected data on stand structure, site conditions, and local bark beetle-induced tree mortality at each trap site. We also collected samples of bark from infested (brood) trees near trap sites to identify and determine the population density of bark beetles that were attacking ponderosa pine, Pinus ponderosa Douglas ex Lawson, in the area surrounding the traps. Multiple regression models indicated that the number of Dendroctonus and Ips beetles captured in 2005 was inversely related to elevation of the trap site, and positively associated with the amount of ponderosa pine in the stand surrounding the site. Traps located closer to brood trees also captured more beetles. The relationship between trap catches and host tree mortality was weak and inconsistent in forest stands surrounding the funnel traps, suggesting that trap catches do not provide a good estimate of local beetle-induced tree mortality. However, pheromone-baited funnel trap data and data from gallery identification in bark samples produced statistically similar relative abundance profiles for the five species of bark beetles that we examined, indicating that funnel trap data provided a good assessment of species presence and relative abundance.

Many-body Study of Core-valence Partitioning and Correlation in Systems with Large-Z Element

NASA Astrophysics Data System (ADS)

Zehtabi-Oskuie, Ana

This thesis presents optical trapping of various single nanoparticles, and the method for integrating the optical trap system into a microfluidic channel to examine the trapping stiffness and to study binding at the single molecule level. Optical trapping is the capability to immobilize, move, and manipulate small objects in a gentle way. Conventional trapping methods are able to trap dielectric particles with size greater than 100 nm. Optical trapping using nanostructures has overcome this limitation so that it has been of interest to trap nanoparticles for bio-analytical studies. In particular, aperture optical trapping allows for trapping at low powers, and easy detection of the trapping events by noting abrupt jumps in the transmission intensity of the trapping beam through the aperture. Improved trapping efficiency has been achieved by changing the aperture shape from a circle; for example, to a rectangle, double nanohole (DNH), or coaxial aperture. The DNH has the advantage of a well-defined trapping region between the two cusps where the nanoholes overlap, which typically allows only single particle trapping due to steric hindrance. Trapping of 21 nm encapsulated quantum dot has been achieved which shows optical trapping can be used in technologies that seek to place a quantum dot at a specific location in a plasmonic or nanophotonic structure. The DNH has been used to trap and unfold a single protein. The high signal-to-noise ratio of 33 in monitoring single protein trapping and unfolding shows a tremendous potential for using the double nanohole as a sensor for protein binding events at a single molecule level. The DNH integrated in a microfluidic chip with flow to show that stable trapping can be achieved under reasonable flow rates of a few microL/min. With such stable trapping under flow, it is possible to envision co-trapping of proteins to study their interactions. Co-trapping is achieved for the case where we flow in a protein (bovine serum albumin -- BSA) and co-trap its antibody (anti-BSA).

ARTIST: An International Project Investigating Aerosol Retention in a Ruptured Steam Generator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guentay, S.; Dehbi, A.; Suckow, D.

2002-07-01

Steam generator tube ruptures (SGTR) with a concurrent stuck open safety relief valve are counted among the risk dominant accident sequences because of the potential for radioactive products to bypass the containment. Owing to the absence of relevant empirical data and the complexity of the geometry and controlling processes, the aerosol removal in the steam generator (SG) tubes and in the secondary side is not well understood. Therefore, little or no credit is usually taken for aerosol retention due to natural processes in the various components of a SG. To help reduce the uncertainties associated with fission product release followingmore » an SGTR sequence, the Paul Scherrer Institut has initiated an international experimental project to be performed in the ARTIST (AeRosol Trapping In a Steam generaTor) facility in the time period from 2002 to 2007. The ARTIST test section is a scaled model of a real SG, and is comprised of a 264-tube bundle with a maximum height of 3.8 m, as well as one full-size droplet separator and one full-size steam dryer. The ARTIST facility is capable of producing soluble and insoluble aerosols and entrain them at sonic gas flow rates (up to 0.25 kg/s, thus matching comparable values predicted by the codes. In addition, aerosols can be generated at prototypical concentrations (up to 5 g/m{sup 3}) and sizes (0.2-5 mm AMMD). State of the art instrumentation is used (Low-pressure impactors, photometers, on-line particle sizer, online droplet sizer, etc.). The ARTIST project will simulate the flow and retention of aerosol-borne fission products in the SG, and provide a unique database to support safety assessments and analytical models. The project is foreseen in seven phases: 1) Aerosol retention in the tube under dry secondary side conditions, 2) Aerosol retention in the near field close to break under dry conditions, 3) Aerosol retention in the bundle far field under dry conditions, 4) Aerosol retention in the separator and dryer under dry conditions, 5) Aerosol retention in the bundle section under wet conditions, 6) Droplet retention in separator and dryer sections and 7) Integral tests to examine overall retention in the SG unit. The project will investigate phenomena at the separate effect and integral levels, and will also address selected accident management (AM) issues. The kick-off experiments are scheduled for the first half of 2002, and some early results will be summarized at the meeting. (authors)« less

High-flow bypass and wrap-clipping for ruptured blood blister-like aneurysm of the internal carotid artery using intraoperative monitoring of cerebral hemodynamics

PubMed Central

Kubo, Yoshitaka; Koji, Takahiro; Yoshida, Kenji; Saito, Hideo; Ogawa, Akira; Ogasawara, Kuniaki

2015-01-01

Aneurysms at non-branching sites in the supraclinoid internal carotid artery (ICA) can be classified as “blood blister-like aneurysms” (BBAs), which have blood blister-like configurations and fragile walls. While surgical treatment for the BBA in the acute stage is recommended, the optimal surgical procedure remains controversial. In the study reported here, we describe the case of a 37-year-old woman with a ruptured BBA in the ophthalmic segment of the right ICA who underwent wrap-clipping with external carotid artery–internal carotid artery bypass by intraoperative estimation of the measurement of cortical cerebral blood flow (CoBF) using a thermal diffusion flow probe. Trapping of the ICA in the acute stage of subarachnoid hemorrhage may result in ischemic complications secondary to hemodynamic hypoperfusion or occlusion of the perforating artery, and/or delayed vasospasm, even with concomitant bypass surgery. We believe that it is important to perform scheduled external carotid artery–internal carotid artery bypass before trapping of the ICA in patients with a ruptured BBA in the acute stage of subarachnoid hemorrhage and to perform wrap-clipping rather than trapping. This would provide much more CoBF if a reduction of CoBF occurs after trapping occlusion of the ICA including a ruptured BBA according to intraoperative CoBF monitoring. As far as we are aware, the case reported here is the first report on high-flow bypass and wrap-clipping for a ruptured BBA of the ICA using intraoperative monitoring of cerebral hemodynamics. PMID:26082641

Monitoring and Managing Codling Moth Clearly and Precisely

USDA-ARS?s Scientific Manuscript database

Studies were conducted in two ‘Comice’ pear orchards treated with sex pheromone in southern Oregon to implement the use of site-specific management practices for codling moth. The density of monitoring traps was increased and insecticide sprays were applied based on moth catch thresholds. Only porti...

A comparison of the Nzi, Horse Pal® and Bite-Lite® H-traps and selected baits for the collection of adult Tabanidae in Florida and North Carolina.

PubMed

Kline, Daniel L; Hogsette, Jerome A; Rutz, Donald A

2018-06-01

Despite the veterinary and medical importance of horse flies, deer flies, and yellow flies, only a few trap types have been evaluated to monitor adult population dynamics. Currently, three trap types are being utilized (H-trap, Horse Pal® (HP), and Nzi trap), but no head-to-head comparisons have been reported. Thus, we conducted comparative trapping studies in Florida and North Carolina. At two study sites in Florida, the efficacy of all three trap types was compared, but only the H-trap and HP were compared in North Carolina. Although trap type was significant at all sites, the trap type which caught the most specimens was not the same. In Florida at the Lower Suwannee Wildlife Refuge (LSWR) site, the H-trap caught the most specimens (2,006), followed in decreasing order by Nzi (938) and HP (541). At the Cedar Ridge Ranch site, the Nzi caught significantly more specimens (1,439) than the H-trap (215) and HP (161), which were not significantly different from each other. In North Carolina, the H-trap caught approximately twice as many specimens as the HP (1,458 vs 720). These trap comparison studies were followed up by a study on the efficacy of various bait combinations: (No Bait (NB), dry ice only (DI), Trap Tech Lure (TTL) only, and DI + TTL), which was conducted only at the two Florida sites with H-traps. At both sites, bait combinations significantly affected trap collections. One pattern (DI +TTL > DI > TTL > NB) was recorded at the LSWR, while at the Cedar River Ranch the pattern was DI > DI +TTL > TTL > NB. Our data showed that trap type and bait combination significantly influence overall adult tabanid abundance as well as individual species composition. © 2018 The Society for Vector Ecology.

Evaluation of temperature sum models and timing of Quassia amara (Simaroubaceae) wood-chip extract to control apple sawfly (Hoplocampa testudinea Klug) in Sweden.

PubMed

Sjöberg, P; Swiergiel, W; Neupane, D; Lennartsson, E; Thierfelder, T; Tasin, M; Rämert, B

Apple sawfly ( Hoplocampa testudinea Klug) is a serious pest in European organic apple production. They hatch during a short period only, making correct timing of control measures crucial. Swedish organic growers have requested a strategy for optimal timing of the Quassia amara (Simaroubaceae) extract against the apple sawfly. The aim of this study was, therefore, to develop methods to predict the timing of Q. amara control in Sweden. A temperature sum model for timely placement of monitoring or mass-trapping sticky traps was validated for Swedish conditions. The average emergence of sawflies occurred at 169 degree days (SD = 20) counted from March 15 (threshold temperature 4 °C). The difference in emergence from existing first flight model of average and maximum 9 and 39 degree days (1 and 9 calendar days) was found acceptable. Accumulated oviposition of 85 % at full bloom (BBCH 65) suggests that mass trapping and monitoring could stop at this time. This is supported by a tendency of decreased trap catches during that period. Three application times for Q. amara were compared: (A) at petal fall (BBCH 67), (B) at a date calculated using female trap catch numbers and temperature sums, and (C) prior to peak egg hatch observed in the field. All treatments resulted in significantly lower percentage of damaged apples compared to the unsprayed control, with significantly less damage (1.3 %) in plots treated according to method (B). The results provide information on adult phenology and methods that could be used to determine timing of mass trapping and insecticide application against the apple sawfly.

Occupancy models for monitoring marine fish: a bayesian hierarchical approach to model imperfect detection with a novel gear combination.

PubMed

Coggins, Lewis G; Bacheler, Nathan M; Gwinn, Daniel C

2014-01-01

Occupancy models using incidence data collected repeatedly at sites across the range of a population are increasingly employed to infer patterns and processes influencing population distribution and dynamics. While such work is common in terrestrial systems, fewer examples exist in marine applications. This disparity likely exists because the replicate samples required by these models to account for imperfect detection are often impractical to obtain when surveying aquatic organisms, particularly fishes. We employ simultaneous sampling using fish traps and novel underwater camera observations to generate the requisite replicate samples for occupancy models of red snapper, a reef fish species. Since the replicate samples are collected simultaneously by multiple sampling devices, many typical problems encountered when obtaining replicate observations are avoided. Our results suggest that augmenting traditional fish trap sampling with camera observations not only doubled the probability of detecting red snapper in reef habitats off the Southeast coast of the United States, but supplied the necessary observations to infer factors influencing population distribution and abundance while accounting for imperfect detection. We found that detection probabilities tended to be higher for camera traps than traditional fish traps. Furthermore, camera trap detections were influenced by the current direction and turbidity of the water, indicating that collecting data on these variables is important for future monitoring. These models indicate that the distribution and abundance of this species is more heavily influenced by latitude and depth than by micro-scale reef characteristics lending credence to previous characterizations of red snapper as a reef habitat generalist. This study demonstrates the utility of simultaneous sampling devices, including camera traps, in aquatic environments to inform occupancy models and account for imperfect detection when describing factors influencing fish population distribution and dynamics.

Occupancy Models for Monitoring Marine Fish: A Bayesian Hierarchical Approach to Model Imperfect Detection with a Novel Gear Combination

PubMed Central

Coggins, Lewis G.; Bacheler, Nathan M.; Gwinn, Daniel C.

2014-01-01

Occupancy models using incidence data collected repeatedly at sites across the range of a population are increasingly employed to infer patterns and processes influencing population distribution and dynamics. While such work is common in terrestrial systems, fewer examples exist in marine applications. This disparity likely exists because the replicate samples required by these models to account for imperfect detection are often impractical to obtain when surveying aquatic organisms, particularly fishes. We employ simultaneous sampling using fish traps and novel underwater camera observations to generate the requisite replicate samples for occupancy models of red snapper, a reef fish species. Since the replicate samples are collected simultaneously by multiple sampling devices, many typical problems encountered when obtaining replicate observations are avoided. Our results suggest that augmenting traditional fish trap sampling with camera observations not only doubled the probability of detecting red snapper in reef habitats off the Southeast coast of the United States, but supplied the necessary observations to infer factors influencing population distribution and abundance while accounting for imperfect detection. We found that detection probabilities tended to be higher for camera traps than traditional fish traps. Furthermore, camera trap detections were influenced by the current direction and turbidity of the water, indicating that collecting data on these variables is important for future monitoring. These models indicate that the distribution and abundance of this species is more heavily influenced by latitude and depth than by micro-scale reef characteristics lending credence to previous characterizations of red snapper as a reef habitat generalist. This study demonstrates the utility of simultaneous sampling devices, including camera traps, in aquatic environments to inform occupancy models and account for imperfect detection when describing factors influencing fish population distribution and dynamics. PMID:25255325

Captures of Ostrinia furnacalis (Lepidoptera: Crambidae) With Sex Pheromone Traps in NE China Corn and Soybeans.

PubMed

Chen, Ri-Zhao; Li, Lian-Bing; Klein, Michael G; Li, Qi-Yun; Li, Peng-Pei; Sheng, Cheng-Fa

2016-02-01

Ostrinia furnacalis (Guenée) (Lepidoptera: Crambidae), commonly referred to as the Asian corn borer, is the most important corn pest in Asia. Although capturing males with pheromone traps has recently been the main monitoring tool and suppression technique, the best trap designs remain unclear. Commercially available Delta and funnel traps, along with laboratory-made basin and water traps, and modified Delta traps, were evaluated in corn and soybean fields during 2013-2014 in NE China. The water trap was superior for capturing first-generation O. furnacalis (1.37 times the Delta trap). However, the basin (8.3 ± 3.2 moths/trap/3 d), Delta (7.9 ± 2.5), and funnel traps (7.0 ± 2.3) were more effective than water traps (1.4 ± 0.4) during the second generation. Delta traps gave optimal captures when deployed at ca. 1.57 × the highest corn plants, 1.36× that of average soybean plants, and at the field borders. In Delta traps modified by covering 1/3 of their ends, captures increased by ca. 15.7 and 8.1% in the first and second generations, respectively. After 35 d in the field, pheromone lures were still ca. 50% as attractive as fresh lures, and retained this level of attraction for ca. 25 more days. Increased captures (first and second generation: 90.9 ± 9.5%; 78.3 ± 9.3%) were obtained by adding a lure exposed for 5 d to funnel traps baited with a 35-d lure. © The Authors 2015. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Real-time interactive 3D manipulation of particles viewed in two orthogonal observation planes.

PubMed

Perch-Nielsen, Ivan; Rodrigo, Peter; Glückstad, Jesper

2005-04-18

The generalized phase contrast (GPC) method has been applied to transform a single TEM00 beam into a manifold of counterpropagating-beam traps capable of real-time interactive manipulation of multiple microparticles in three dimensions (3D). This paper reports on the use of low numerical aperture (NA), non-immersion, objective lenses in an implementation of the GPC-based 3D trapping system. Contrary to high-NA based optical tweezers, the GPC trapping system demonstrated here operates with long working distance (>10 mm), and offers a wider manipulation region and a larger field of view for imaging through each of the two opposing objective lenses. As a consequence of the large working distance, simultaneous monitoring of the trapped particles in a second orthogonal observation plane is demonstrated.

ANTS AS BIOLOGICAL INDICATORS FOR MONITORING CHANGES IN ARID ENVIRONMENTS: LESSONS FOR MONITORING PROTECTED AREAS

EPA Science Inventory

The responses of ant communities to structural change (removal of an invasive were studied in a replicated experiment in a Chihuahuan Desert grassland. The results from sampling of ant communities by pit-fall trapping were validated by mapping ant colonies on the experimental plo...

40 CFR 75.84 - Recordkeeping and reporting.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) CONTINUOUS EMISSION MONITORING Hg Mass Emission Provisions § 75.84 Recordkeeping and reporting... Federal Hg mass emission reduction program”; (2) The information required in § 75.58(b)(3), for units with... or sorbent trap monitoring systems, for each hour when the unit is operating, record the Hg mass...

Monitoring Amyelois transitella Males and Females with Phenyl Propionate Traps in Almonds and Pistachios

USDA-ARS?s Scientific Manuscript database

Attractants that lure both sexes and both mated and unmated females have been used to monitor the effect of mating disruption on the mating status and relative abundance of lepidopteran females. For the navel orangeworm, Amyelois transitella (Walker) (Lepidoptera: Pyralidae), phenyl propionate attra...

Epidemiology and control of rusts of wheat and barley

USDA-ARS?s Scientific Manuscript database

Rusts of wheat and barley were monitored throughout the Pacific Northwest (PNW) using trap plots and through field surveys during the 2008 growing season. Through collaborators in other states, stripe rusts of wheat and barley were monitored throughout the US. In 2008, stripe rust occurred in 18 st...

Forest fragments as barriers to fruit fly dispersal: Anastrepha (Diptera: Tephritidae) populations in orchards and adjacent forest fragments in Puerto Rico.

PubMed

Jenkins, David A; Kendra, Paul E; Van Bloem, Skip; Whitmire, Stefanie; Mizell, Russ; Goenaga, Ricardo

2013-04-01

McPhail-type traps baited with ammonium acetate and putrescine were used to monitor populations of Anastrepha obliqua (Macquart) and Anastrepha suspensa (Loew) in two orchards with hosts of these flies (mango, Mangifera indica L., and carambola, Averrhoa carambola L.), as well as in forest fragments bordering these orchards. Contour maps were constructed to measure population distributions in and around orchards. Our results indicate that Anastrepha populations are focused around host fruit in both space and time, that traps do not draw fruit flies away from hosts, even when placed within 15 m of the host, and that lures continue to function for 6 mo in the field. The contour mapping analyses reveal that populations of fruit flies are focused around ovipositional hosts. Although the trapping system does not have a very long effective sampling range, it is ideal, when used in combination with contour analyses, for assessing fine-scale (on the order of meters) population distributions, including identifying resources around which fly populations are focused or, conversely, assessing the effectiveness of management tools. The results are discussed as they pertain to monitoring and detecting Anastrepha spp. with the McPhail-type trap and ammonium acetate and putrescine baiting system and the dispersal of these flies within Puerto Rico.

Supplement Analysis for the Grande Ronde Basin Endemic Spring Chinook Salmon Supplementation Program EA (DOE/EA-1173/SA-01)

DOE Office of Scientific and Technical Information (OSTI.GOV)

N /A

2003-12-18

The CTUIR and ODFW propose to expand their monitoring and evaluation for the Grande Ronde spring chinook supplementation program to take additional data on summer steelhead that are trapped at the existing adult collection weirs on the upper Grande Ronde River and Catherine Creek. The weirs are a movable design and are operated seasonally during the adult chinook migration. Bull trout and summer steelhead have been trapped at the weirs since 1997 incidental to the spring chinook broodstock collection activities. Minimal data is recorded on both species as a requirement of the ESA permits, and reported to USFWS and NOAAmore » Fisheries. This supplement analysis covers a minor expansion of the program to collect more extensive life history data on summer steelhead. The weir and trap will be installed 2-3 weeks earlier (early to mid-March) than was previously needed for the spring chinook broodstock collection in order to monitor the summer steelhead migration period. The adult steelhead will be captured in the traps, anesthetized, and measured. Data will be recorded on the date of capture, fork length, sex, markings, and maturity of the fish, and scale and punch tissue samples will be taken for genetic analyses.« less

Real-time quantitative analysis of H2, He, O2, and Ar by quadrupole ion trap mass spectrometry.

PubMed

Ottens, Andrew K; Harrison, W W; Griffin, Timothy P; Helms, William R

2002-09-01

The use of a quadrupole ion trap mass spectrometer (QITMS) for quantitative analysis of hydrogen and helium as well as of other permanent gases is demonstrated. Like commercial instruments, the customized QITMS uses mass selective instability; however, this instrument operates at a greater trapping frequency and without a buffer gas. Thus, a useable mass range from 2 to over 50 daltons (Da) is achieved. The performance of the ion trap is evaluated using part-per-million (ppm) concentrations of hydrogen, helium, oxygen, and argon mixed into a nitrogen gas stream, as outlined by the National Aeronautics and Space Administration (NASA), which is interested in monitoring for cryogenic fuel leaks within the Space Shuttle during launch preparations. When quantitating the four analytes, relative accuracy and precision were better than the NASA-required minimum of 10% error and 5% deviation, respectively. Limits of detection were below the NASA requirement of 25-ppm hydrogen and 100-ppm helium; those for oxygen and argon were within the same order of magnitude as the requirements. These results were achieved at a fast data recording rate, and demonstrate the utility of the QITMS as a real-time quantitative monitoring device for permanent gas analysis. c. 2002 American Society for Mass Spectrometry.

Monitoring of the Red-Belted Clearwing Moth, Synanthedon myopaeformis, and its Parasitoid Liotryphon crassiseta in Apple Orchards in Yellow Moericke Traps

PubMed Central

Bąkowski, Marek; Piekarska-Boniecka, Hanna; Dolańska-Niedbała, Ewa

2013-01-01

This study was conducted in 2008–2010 in three apple orchards in western Poland and involved a massive catch of the red-belted clearwing moth, Synanthedon myopaeformis (Borkhausen) (Lepidoptera: Sesiidae), and its parasitoid Liotryphon crassiseta (Thomson) (Hymenoptera: Ichneumonidae) in yellow Moericke traps. The flight time for both species was correlated and fell in the first half of July. However, the correlation between the occurrences of both species was statistically significant only in 2008, when most specimens were caught. A total of 7960 S. myopaeformis were caught, with a 2:1 male:female sex ratio, and 415 adult L. crassiseta. No correlation between the numbers of S. myopaeformis and L. crassiseta in relation to age, variety of trees, or orchard surface area was noted. Significant differences between the catches of S. myopaeformis and L. crassiseta were reported in particular years. Furthermore, clear differences in the yields of S. myopaeformis and L. crassiseta between traps situated in the orchard and those on its edges were recorded, particularly in the orchard surrounded by cultivated fields. Yellow pan-traps could be used more widely in order to monitor and control the abundance of S. myopaeformis, especially by catching its females. PMID:23879220

Arthropod Surveillance Programs: Basic Components, Strategies, and Analysis.

PubMed

Cohnstaedt, Lee W; Rochon, Kateryn; Duehl, Adrian J; Anderson, John F; Barrera, Roberto; Su, Nan-Yao; Gerry, Alec C; Obenauer, Peter J; Campbell, James F; Lysyk, Tim J; Allan, Sandra A

2012-03-01

Effective entomological surveillance planning stresses a careful consideration of methodology, trapping technologies, and analysis techniques. Herein, the basic principles and technological components of arthropod surveillance plans are described, as promoted in the symposium "Advancements in arthropod monitoring technology, techniques, and analysis" presented at the 58th annual meeting of the Entomological Society of America in San Diego, CA. Interdisciplinary examples of arthropod monitoring for urban, medical, and veterinary applications are reviewed. Arthropod surveillance consists of the three components: 1) sampling method, 2) trap technology, and 3) analysis technique. A sampling method consists of selecting the best device or collection technique for a specific location and sampling at the proper spatial distribution, optimal duration, and frequency to achieve the surveillance objective. Optimized sampling methods are discussed for several mosquito species (Diptera: Culicidae) and ticks (Acari: Ixodidae). The advantages and limitations of novel terrestrial and aerial insect traps, artificial pheromones and kairomones are presented for the capture of red flour beetle (Coleoptera: Tenebrionidae), small hive beetle (Coleoptera: Nitidulidae), bed bugs (Hemiptera: Cimicidae), and Culicoides (Diptera: Ceratopogonidae) respectively. After sampling, extrapolating real world population numbers from trap capture data are possible with the appropriate analysis techniques. Examples of this extrapolation and action thresholds are given for termites (Isoptera: Rhinotermitidae) and red flour beetles.

Arthropod Surveillance Programs: Basic Components, Strategies, and Analysis

PubMed Central

Rochon, Kateryn; Duehl, Adrian J.; Anderson, John F.; Barrera, Roberto; Su, Nan-Yao; Gerry, Alec C.; Obenauer, Peter J.; Campbell, James F.; Lysyk, Tim J.; Allan, Sandra A.

2015-01-01

Effective entomological surveillance planning stresses a careful consideration of methodology, trapping technologies, and analysis techniques. Herein, the basic principles and technological components of arthropod surveillance plans are described, as promoted in the symposium “Advancements in arthropod monitoring technology, techniques, and analysis” presented at the 58th annual meeting of the Entomological Society of America in San Diego, CA. Interdisciplinary examples of arthropod monitoring for urban, medical, and veterinary applications are reviewed. Arthropod surveillance consists of the three components: 1) sampling method, 2) trap technology, and 3) analysis technique. A sampling method consists of selecting the best device or collection technique for a specific location and sampling at the proper spatial distribution, optimal duration, and frequency to achieve the surveillance objective. Optimized sampling methods are discussed for several mosquito species (Diptera: Culicidae) and ticks (Acari: Ixodidae). The advantages and limitations of novel terrestrial and aerial insect traps, artificial pheromones and kairomones are presented for the capture of red flour beetle (Coleoptera: Tenebrionidae), small hive beetle (Coleoptera: Nitidulidae), bed bugs (Hemiptera: Cimicidae), and Culicoides (Diptera: Ceratopogonidae) respectively. After sampling, extrapolating real world population numbers from trap capture data are possible with the appropriate analysis techniques. Examples of this extrapolation and action thresholds are given for termites (Isoptera: Rhinotermitidae) and red flour beetles. PMID:26543242

Correlation between the proportion of stained eggs and the number of mites (Dermanyssus gallinae) monitored using a 'non-parallel board trap'.

PubMed

Odaka, Makiko; Ogino, Kazumasa; Shikada, Michitaka; Asada, Kenichi; Kasa, Syoujirou; Inoue, Takahiro; Maeda, Ken

2017-12-01

The poultry red mite (Dermanyssus gallinae) is a serious problem for the poultry industry worldwide. However, the relationship between the mite population and the damage that they cause is still unclear. In this study, the mite population in poultry houses was examined using an established trap method, and the risk of blood-stained eggs caused by the mites was assessed. Traps were placed once a week outside the egg channels and/or on the floor in two poultry farms in Fukuoka Prefecture, Japan, from April 2012 to July 2014. The numbers of blood-stained eggs and total eggs were counted at weekly intervals. The results showed that the number of mites increased from April to May, and reached a peak around the beginning of June when the average temperature and humidity were >24°C and 70-90%, respectively. In the segmented model, the correlation between the proportion of blood-stained eggs and the number of mites or temperature was positive over a threshold. In conclusion, our established trap method is useful for monitoring mites and can be used to predict when poultry farms should be treated to prevent appearance of blood-stained eggs. © 2017 Japanese Society of Animal Science.

Evaluation of the cure kinetics of the wood/pMDI bondline

Treesearch

David P. Harper; Michael P. Wolcott; Timothy G. Rials

2001-01-01

Micro-dielectric analysis (µDEA) and differentia1 scanning calorimetry (DSC) were used to monitor cure of polymeric diphenyl-methane diisocyanate (pMDI) resin with wood strands in a saturated steam environment. A first-order autocatalyzed kinetic model was employed to determine kinetic parameters. The kinetics were found to follow an Arrhenius relation. A single ramp...

46 CFR 62.35-50 - Tabulated monitoring and safety control requirements for specific systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Status Main (Propulsion steam) turbine (2) (2) (2) (4, 5) Manual trip Main propulsion, diesel (1) (1) (1... Temperature High Generators Ship service (1) (1) Starting pressure/voltage Low Tripped Emergency (5) (5) (5) Turbogenerator (1,6) (1,6) (6) Manual trip Diesel (1,7) (1,7) (7) (5) Manual trip Auxiliary boiler Run Trip (12...

An automatic system to study sperm motility and energetics

PubMed Central

Nascimento, Jaclyn M.; Chandsawangbhuwana, Charlie; Botvinick, Elliot L.; Berns, Michael W.

2012-01-01

An integrated robotic laser and microscope system has been developed to automatically analyze individual sperm motility and energetics. The custom-designed optical system directs near-infrared laser light into an inverted microscope to create a single-point 3-D gradient laser trap at the focal spot of the microscope objective. A two-level computer structure is described that quantifies the sperm motility (in terms of swimming speed and swimming force) and energetics (measuring mid-piece membrane potential) using real-time tracking (done by the upper-level system) and fluorescent ratio imaging (done by the lower-level system). The communication between these two systems is achieved by a gigabit network. The custom-built image processing algorithm identifies the sperm swimming trajectory in real-time using phase contrast images, and then subsequently traps the sperm by automatically moving the microscope stage to relocate the sperm to the laser trap focal plane. Once the sperm is stably trapped (determined by the algorithm), the algorithm can also gradually reduce the laser power by rotating the polarizer in the laser path to measure the trapping power at which the sperm is capable of escaping the trap. To monitor the membrane potential of the mitochondria located in a sperm’s mid-piece, the sperm is treated with a ratiometrically-encoded fluorescent probe. The proposed algorithm can relocate the sperm to the center of the ratio imaging camera and the average ratio value can be measured in real-time. The three parameters, sperm escape power, sperm swimming speed and ratio values of the mid-piece membrane potential of individual sperm can be compared with respect to time. This two-level automatic system to study individual sperm motility and energetics has not only increased experimental throughput by an order of magnitude but also has allowed us to monitor sperm energetics prior to and after exposure to the laser trap. This system should have application in both the human fertility clinic and in animal husbandry. PMID:18299996

An automatic system to study sperm motility and energetics.

PubMed

Shi, Linda Z; Nascimento, Jaclyn M; Chandsawangbhuwana, Charlie; Botvinick, Elliot L; Berns, Michael W

2008-08-01

An integrated robotic laser and microscope system has been developed to automatically analyze individual sperm motility and energetics. The custom-designed optical system directs near-infrared laser light into an inverted microscope to create a single-point 3-D gradient laser trap at the focal spot of the microscope objective. A two-level computer structure is described that quantifies the sperm motility (in terms of swimming speed and swimming force) and energetics (measuring mid-piece membrane potential) using real-time tracking (done by the upper-level system) and fluorescent ratio imaging (done by the lower-level system). The communication between these two systems is achieved by a gigabit network. The custom-built image processing algorithm identifies the sperm swimming trajectory in real-time using phase contrast images, and then subsequently traps the sperm by automatically moving the microscope stage to relocate the sperm to the laser trap focal plane. Once the sperm is stably trapped (determined by the algorithm), the algorithm can also gradually reduce the laser power by rotating the polarizer in the laser path to measure the trapping power at which the sperm is capable of escaping the trap. To monitor the membrane potential of the mitochondria located in a sperm's mid-piece, the sperm is treated with a ratiometrically-encoded fluorescent probe. The proposed algorithm can relocate the sperm to the center of the ratio imaging camera and the average ratio value can be measured in real-time. The three parameters, sperm escape power, sperm swimming speed and ratio values of the mid-piece membrane potential of individual sperm can be compared with respect to time. This two-level automatic system to study individual sperm motility and energetics has not only increased experimental throughput by an order of magnitude but also has allowed us to monitor sperm energetics prior to and after exposure to the laser trap. This system should have application in both the human fertility clinic and in animal husbandry.

Apparatus and methods for supplying auxiliary steam in a combined cycle system

DOEpatents

Gorman, William G.; Carberg, William George; Jones, Charles Michael

2002-01-01

To provide auxiliary steam, a low pressure valve is opened in a combined cycle system to divert low pressure steam from the heat recovery steam generator to a header for supplying steam to a second combined cycle's steam turbine seals, sparging devices and cooling steam for the steam turbine if the steam turbine and gas turbine lie on a common shaft with the generator. Cooling steam is supplied the gas turbine in the combined cycle system from the high pressure steam turbine. Spent gas turbine cooling steam may augment the low pressure steam supplied to the header by opening a high pressure valve whereby high and low pressure steam flows are combined. An attemperator is used to reduce the temperature of the combined steam in response to auxiliary steam flows above a predetermined flow and a steam header temperature above a predetermined temperature. The auxiliary steam may be used to start additional combined cycle units or to provide a host unit with steam turbine cooling and sealing steam during full-speed no-load operation after a load rejection.

Stable isotope monitoring of ionic trapping of CO2 in deep brines

NASA Astrophysics Data System (ADS)

Myrttinen, A.; Barth, J. A. C.; Becker, V.; Blum, P.; Grathwohl, P.

2009-04-01

CO2 injection into a depleted gas-reservoir is used as a combined method for Enhanced Gas Recovery (EGR) and CO2 storage. In order to safeguard this process, monitoring the degree of dissolution and potential further precipitation and mineral interactions are a necessity. Here a method is introduced, in which stable isotope and geochemical data can be used as a monitoring technique to quantify ionic trapping of injected CO2. Isotope and geochemical data of dissolved inorganic carbon (DIC) can be used to distinguish between already present and to be injected inorganic carbon. Injected CO2, for instance, is formed during combustion of former plant material and is expected to have a different isotope ratio (δ13C value) than the baseline data of the aquifer. This is because combusted CO2 originates from organic material, such as coal and oil with a predominant C3 plant signature. Mixing the injected CO2 with groundwater is therefore expected to change the isotope, as well as the geochemical composition of the groundwater. Mass balance calculations with stable isotope ratios can serve to quantify ionic trapping of CO2 as DIC in groundwater. However, depending on the composition of the aquifer, weathering of carbonate or silicates may occur. Enhanced weathering processes due to CO2 injection can also further influence the isotopic composition. Such interactions between dissolved CO2 and minerals depend on the temperature and pressure regimes applied. Field data, as well as laboratory experiments are planned to quantify isotope ratios of dissolved inorganic carbon as well as oxygen isotope ratios of the water. These are indicative of geochemical processes before, during and after EGR. The isotope method should therefore provide a new tool to quantify the efficiency of ionic trapping under various temperatures and pressures. Keywords: Enhanced Gas Recovery, monitoring of CO2 dissolution, stable isotopes

Apparatus and methods of reheating gas turbine cooling steam and high pressure steam turbine exhaust in a combined cycle power generating system

DOEpatents

Tomlinson, Leroy Omar; Smith, Raub Warfield

2002-01-01

In a combined cycle system having a multi-pressure heat recovery steam generator, a gas turbine and steam turbine, steam for cooling gas turbine components is supplied from the intermediate pressure section of the heat recovery steam generator supplemented by a portion of the steam exhausting from the HP section of the steam turbine, steam from the gas turbine cooling cycle and the exhaust from the HP section of the steam turbine are combined for flow through a reheat section of the HRSG. The reheated steam is supplied to the IP section inlet of the steam turbine. Thus, where gas turbine cooling steam temperature is lower than optimum, a net improvement in performance is achieved by flowing the cooling steam exhausting from the gas turbine and the exhaust steam from the high pressure section of the steam turbine in series through the reheater of the HRSG for applying steam at optimum temperature to the IP section of the steam turbine.

Development of a Novel Trap for the Collection of Black Flies of the Simulium ochraceum Complex

PubMed Central

Rodríguez-Pérez, Mario A.; Adeleke, Monsuru A.; Burkett-Cadena, Nathan D.; Garza-Hernández, Javier A.; Reyes-Villanueva, Filiberto; Cupp, Eddie W.; Toé, Laurent; Salinas-Carmona, Mario C.; Rodríguez-Ramírez, Américo D.; Katholi, Charles R.; Unnasch, Thomas R.

2013-01-01

Background Human landing collections are currently the standard method for collecting onchocerciasis vectors in Africa and Latin America. As part of the efforts to develop a trap to replace human landing collections for the monitoring and surveillance of onchocerciasis transmission, comprehensive evaluations of several trap types were conducted to assess their ability to collect Simulium ochraceum sensu lato, one of the principal vectors of Onchocerca volvulus in Latin America. Methodology/Principal Findings Diverse trap designs with numerous modifications and bait variations were evaluated for their abilities to collect S. Ochraceum s.l. females. These traps targeted mostly host seeking flies. A novel trap dubbed the “Esperanza window trap” showed particular promise over other designs. When baited with CO2 and BG-lure (a synthetic blend of human odor components) a pair of Esperanza window traps collected numbers of S. Ochraceum s.l. females similar to those collected by a team of vector collectors. Conclusions/Significance The Esperanza window trap, when baited with chemical lures and CO2 can be used to collect epidemiologically significant numbers of Simulium ochraceum s.l., potentially serving as a replacement for human landing collections for evaluation of the transmission of O. volvulus. PMID:24116169

A brief report on the illegal cage-bird trade in southern Florida: a potentially serious negative impact on the eastern population of Painted Bunting (Passerina ciris)

USGS Publications Warehouse

Sykes, P.W.; Manfredi, L.; Padura, M.

2006-01-01

Populations of Painted Bunting (Passerina ciris) have been declining annually over the past 35 years. A cursory survey indicates that illegal trapping of Painted Buntings for a black market cage-bird trade is widespread in southeastern Florida. Coupled with other negative factors confronting the eastern population, the trapping of buntings for the cagebird trade may, in time, produce dire results for this native songbird. Law enforcement personnel need to continue to monitor the illegal activity of trapping native passerines for the local songbird market and to continue to arrest those who support it.

Traps and attractants for wood-boring insects in ponderosa pine stands in the Black Hills, South Dakota.

PubMed

Costello, Sheryl L; Negrón, José F; Jacobi, William R

2008-04-01

Recent large-scale wildfires have increased populations of wood-boring insects in the Black Hills of South Dakota. Because little is known about possible impacts of wood-boring insects in the Black Hills, land managers are interested in developing monitoring techniques such as flight trapping with semiochemical baits. Two trap designs and four semiochemical attractants were tested in a recently burned ponderosa pine, Pinus ponderosa Dougl. ex Laws., forest in the Black Hills. Modified panel and funnel traps were tested in combination with the attractants, which included a woodborer standard (ethanol and alpha-pinene), standard plus 3-carene, standard plus ipsenol, and standard plus ipsdienol. We found that funnel traps were equally efficient or more efficient in capturing wood-boring insects than modified panel traps. Trap catches of cerambycids increased when we added the Ips spp. pheromone components (ipsenol or ipsdienol) or the host monoterpene (3-carene) to the woodborer standard. During the summers of 2003 and 2004, 18 cerambycid, 14 buprestid, and five siricid species were collected. One species of cerambycid, Monochamus clamator (LeConte), composed 49 and 40% of the 2003 and 2004 trap catches, respectively. Two other cerambycids, Acanthocinus obliquus (LeConte) and Acmaeops proteus (Kirby), also were frequently collected. Flight trap data indicated that some species were present throughout the summer, whereas others were caught only at the beginning or end of the summer.

High-resolution dual-trap optical tweezers with differential detection: alignment of instrument components.

PubMed

Bustamante, Carlos; Chemla, Yann R; Moffitt, Jeffrey R

2009-10-01

Optical traps or "optical tweezers" have become an indispensable tool in understanding fundamental biological processes. Using our design, a dual-trap optical tweezers with differential detection, we can detect length changes to a DNA molecule tethering the trapped beads of 1 bp. By forming two traps from the same laser and maximizing the common optical paths of the two trapping beams, we decouple the instrument from many sources of environmental and instrumental noise that typically limit spatial resolution. The performance of a high-resolution instrument--the formation of strong traps, the minimization of background signals from trap movements, or the mitigation of the axial coupling, for example--can be greatly improved through careful alignment. This procedure, which is described in this article, starts from the laser and advances through the instrument, component by component. Alignment is complicated by the fact that the trapping light is in the near infrared (NIR) spectrum. Standard infrared viewing cards are commonly used to locate the beam, but unfortunately, bleach quickly. As an alternative, we use an IR-viewing charge-coupled device (CCD) camera equipped with a C-mount telephoto lens and display its image on a monitor. By visualizing the scattered light on a pair of irises of identical height separated by >12 in., the beam direction can be set very accurately along a fixed axis.

Uncertainty in particle number modal analysis during transient operation of compressed natural gas, diesel, and trap-equipped diesel transit buses.

PubMed

Holmén, Britt A; Qu, Yingge

2004-04-15

The relationships between transient vehicle operation and ultrafine particle emissions are not well-known, especially for low-emission alternative bus technologies such as compressed natural gas (CNG) and diesel buses equipped with particulate filters/traps (TRAP). In this study, real-time particle number concentrations measured on a nominal 5 s average basis using an electrical low pressure impactor (ELPI) for these two bus technologies are compared to that of a baseline catalyst-equipped diesel bus operated on ultralow sulfur fuel (BASE) using dynamometer testing. Particle emissions were consistently 2 orders of magnitude lower for the CNG and TRAP compared to BASE on all driving cycles. Time-resolved total particle numbers were examined in terms of sampling factors identified as affecting the ability of ELPI to quantify the particulate matter number emissions for low-emitting vehicles such as CNG and TRAP as a function of vehicle driving mode. Key factors were instrument sensitivity and dilution ratio, alignment of particle and vehicle operating data, sampling train background particles, and cycle-to-cycle variability due to vehicle, engine, after-treatment, or driver behavior. In-cycle variability on the central business district (CBD) cycle was highest for the TRAP configuration, but this could not be attributed to the ELPI sensitivity issues observed for TRAP-IDLE measurements. Elevated TRAP emissions coincided with low exhaust temperature, suggesting on-road real-world particulate filter performance can be evaluated by monitoring exhaust temperature. Nonunique particle emission maps indicate that measures other than vehicle speed and acceleration are necessary to model disaggregated real-time particle emissions. Further testing on a wide variety of test cycles is needed to evaluate the relative importance of the time history of vehicle operation and the hysteresis of the sampling train/dilution tunnel on ultrafine particle emissions. Future studies should monitor particle emissions with high-resolution real-time instruments and account for the operating regime of the vehicle using time-series analysis to develop predictive number emissions models.

Economic comparison of the monitoring programmes for bluetongue vectors in Austria and Switzerland.

PubMed

Pinior, B; Brugger, K; Köfer, J; Schwermer, H; Stockreiter, S; Loitsch, A; Rubel, F

2015-05-02

With the bluetongue virus serotype 8 (BTV-8) outbreak in 2006, vector monitoring programmes (according to EU regulation 1266/2007) were implemented by European countries to obtain information on the spatial distribution of vectors and the vector-free period. This study investigates the vector monitoring programmes in Austria and Switzerland by performing a retrospective cost analysis for the period 2006-2010. Two types of costs were distinguished: costs financed directly via the national bluetongue programmes and costs contributed in-kind by the responsible institutions and agricultural holdings. The total net costs of the monitoring programme in Austria amounted to €1,415,000, whereby in Switzerland the costs were valued at €94,000. Both countries followed the legislation complying with requirements, but differed in regard to sampling frequency, number of trap sites and sampling strategy. Furthermore, the surface area of Austria is twice the area of Switzerland although the number of ruminants is almost the same in both countries. Thus, for comparison, the costs were normalised with regard to the sampling frequency and the number of trap sites. Resulting costs per trap sample comprised €164 for Austria and €48 for Switzerland. In both countries, around 50 per cent of the total costs can be attributed to payments in-kind. The benefit of this study is twofold: first, veterinary authorities may use the results to improve the economic efficiency of future vector monitoring programmes. Second, the analysis of the payment in-kind contribution is of great importance to public authorities as it makes the available resources visible and demonstrates how they have been used. British Veterinary Association.

Economic comparison of the monitoring programmes for bluetongue vectors in Austria and Switzerland

PubMed Central

Pinior, B.; Brugger, K.; Köfer, J.; Schwermer, H.; Stockreiter, S.; Loitsch, A.; Rubel, F.

2015-01-01

With the bluetongue virus serotype 8 (BTV-8) outbreak in 2006, vector monitoring programmes (according to EU regulation 1266/2007) were implemented by European countries to obtain information on the spatial distribution of vectors and the vector-free period. This study investigates the vector monitoring programmes in Austria and Switzerland by performing a retrospective cost analysis for the period 2006–2010. Two types of costs were distinguished: costs financed directly via the national bluetongue programmes and costs contributed in-kind by the responsible institutions and agricultural holdings. The total net costs of the monitoring programme in Austria amounted to €1,415,000, whereby in Switzerland the costs were valued at €94,000. Both countries followed the legislation complying with requirements, but differed in regard to sampling frequency, number of trap sites and sampling strategy. Furthermore, the surface area of Austria is twice the area of Switzerland although the number of ruminants is almost the same in both countries. Thus, for comparison, the costs were normalised with regard to the sampling frequency and the number of trap sites. Resulting costs per trap sample comprised €164 for Austria and €48 for Switzerland. In both countries, around 50 per cent of the total costs can be attributed to payments in-kind. The benefit of this study is twofold: first, veterinary authorities may use the results to improve the economic efficiency of future vector monitoring programmes. Second, the analysis of the payment in-kind contribution is of great importance to public authorities as it makes the available resources visible and demonstrates how they have been used. PMID:25841165

Evaluation of mosquito (Diptera: Culicidae) species richness using two sampling methods in the hydroelectric reservoir of Simplício, Minas Gerais, Brazil.

PubMed

Alencar, Jeronimo; de Mello, Viviane Soares; Serra-Freire, Nicolau Maués; Silva, Júlia dos Santos; Morone, Fernanda; Guimarães, Anthony Érico

2012-04-01

We compared two types of light traps used for monitoring mosquito abundance in the hydroelectric reservoir of Simplício, Além Paraíba - Minas Gerais. Mosquitoes were captured bimonthly using automatic CDC and Shannon traps before the filling of the hydroelectric plant reservoir from December 2008 to December 2009. In total, 1474 specimens from 13 genera were captured. Among the captured specimens, several species known to be vectors of disease-causing agents for humans and/or animals were identified, including Anopheles aquasalis, Aedes albopictus, Coquillettidia venezuelensis, Haemagogus leucocelaenus, and Aedes scapularis. Sampling efficacy between the four capture sites was not found to be significantly different, irrespective of species captured or type of trap used. Poor correlation (r (x, y) = -0.0444) between the number of mosquito species and capture site was observed when not influenced by the type of trap used. Among the installation sites of the CDC and Shannon traps in the areas investigated, CDC traps fixed in livestock shelters obtained an overall higher abundance of species captured.

Large Cleaner Detectors for the UCN τ Neutron Lifetime Experiment

NASA Astrophysics Data System (ADS)

Gonzalez, Francisco; UCNtau Collaboration

2017-09-01

The UCN τ experiment at Los Alamos National Laboratory measures the neutron β-decay lifetime by storing ultracold neutrons (UCNs) in a magneto-gravitational trap for holding times longer than the neutron's lifetime. Neutrons with energies above the trapping potential can escape the trap, giving rise to a systematic error. To mitigate this effect, a large polyethylene sheet is lowered into the trap to remove the high energy unbound neutrons. High energy UCN upscatter in the polyethylene sheet and leave the trap. Such a ``UCN spectrum cleaner,'' covering half the trap top, was shown to be effective in removing high-energy neutrons in previous run cycles. During this run cycle, the UCN τ collaboration has added two thermal neutron detectors on the spectrum cleaner. The new thermal neutron detectors will monitor high-energy neutrons throughout upcoming run cycles, providing important information on the neutron normalization, spectral cleaning, and heating during storage. These detectors use LiF-ZnS sheets coupled to a wavelength-shifting plastic slab, with silicon photomultipliers attached to the edges. We will present results of the light detection simulation and performance tests of these detectors.