Ways to Improve the Quality of Die Steel 5KhNM

NASA Astrophysics Data System (ADS)

Efimov, S. V.; Malykhina, O. Yu; Pavlova, A. G.; Milyuts, V. G.; Tsukanov, V. V.; Vikharev, V. V.

2017-12-01

There was performed an analysis of influence of the deoxidation technology, hydrogen content and high concentration of titanium in steel 5KhNM (Rus. “5XHM”) on quality of die blanks, evaluated based on the results of the ultrasonic test. The fractographic examinations of fractures and the X-ray microprobe analysis of chemical composition of non-metallic inclusions were conducted, the evaluation of macro- and micro-structure of a die blank with high titanium content was performed. It is demonstrated that defects of dies from steel 5KhNM (Rus. “5XHM”) are cracks from merged flakes and micro-flakes; in most cases large concentrations of sulphides appeared to be hydrogen collectors for formation of flakes and micro-flakes.

Studying damage accumulation in martensitic corrosion-resistant steel under cold radial reduction

NASA Astrophysics Data System (ADS)

Karamyshev, A. P.; Nekrasov, I. I.; Nesterenko, A. V.; Parshin, V. S.; Smirnov, S. V.; Shveikin, V. P.; Fedulov, A. A.

2017-12-01

Cold radial reduction of specimens made of the Kh17N2 corrosion-resistant martensitic steel is studied on a lever-type radial-forging machine (RFM). The mechanical properties of the deformed specimens, the "damage accumulation - strain" relation in the specimens are obtained with the application of hydrostatic and fractographic methods for fractured specimens. The damage of the Kh17N2 corrosion-resistant steel is evaluated as a result of an experimental study considering the data of simulation by a complex finite element model of cold deformation on a lever-type RFM.

On the possibility of producing piston pins for diesel engines from steel 18KhGT with the use of mechanical and chemical heat treatment

NASA Astrophysics Data System (ADS)

Zolot'ko, V. A.

1997-06-01

At the present time pisto pins of highly loaded diesel engines are produced by mechanical treatment from tube preforms of steel 12KhN3A and carburized by subsequent heat treatment. The high cost of domestic steel and the absence of preforms of the requisite size make it necessary to choose a less scare material and develop a treatment process that would provide the requisite operational characteristics of the parts. The present work is devoted to a study of the possibility of using for the purpose steel 18KhGT in a state of substructural toughening created by cold plastic straining (CPS) and a stabilizing heat treatment with subsequent ion nitriding.

Structural transformations, strengthening, and wear resistance of titanium nickelide upon abrasive and adhesive wear

NASA Astrophysics Data System (ADS)

Korshunov, L. G.; Pushin, V. G.; Chernenko, N. L.; Makarov, V. V.

2010-07-01

Wear resistance and structural transformations upon abrasive and adhesive wear of titanium nickelide Ti49.4Ni50.6 in microcrystalline (MC) and submicrocrystalline (SMC) states have been investigated. It has been shown that the abrasive wear resistance of this alloy exceeds that of the steel 12Kh18N9 by a factor of about 2, that of the steel 110G13 (Hadfield steel), by a factor of 1.3, and is close to that of the steel 95Kh18. Upon adhesive wear in a testing-temperature range from -50 to +300°C, the Ti49.4Ni50.6 alloy, as compared to the steel 12Kh18N9, is characterized by the wear rate that is tens of times smaller and by a reduced (1.5-2.0 times) friction coefficient. The enhanced wear resistance of the Ti49.4Ni50.6 alloy is due to the development of intense strain hardening in it and to a high fracture toughness, which is a consequence of effective relaxation of high contact stresses arising in the surface layer of the alloy. The SMC state produced in the alloy with the help of equal-channel angular pressing (ECAP) has no effect on the abrasive wear resistance of the alloy. The favorable effect of ECAP on the wear resistance of the Ti49.4Ni50.6 alloy takes place under conditions of its adhesive wear at temperatures from -25 to +70°C. The electron-microscopic investigation showed that under conditions of wear at negative and room temperatures in the surface layer (1-5 μm thick) of titanium nickelide there arises a mixed structure consisting of an amorphous phase and nanocrystals of supposedly austenite and martensite. Upon friction at 200-300°C, a nanocrystalline structure of the B2 phase arises near the alloy surface, which, as is the case with the amorphous-nanocrystalline structure, is characterized by significant effective strength and wear resistance.

Structural transformations in hull material clad by nitrogen stainless steel using various methods

NASA Astrophysics Data System (ADS)

Sagaradze, V. V.; Kataeva, N. V.; Mushnikova, S. Yu.; Khar'kov, O. A.; Kalinin, G. Yu.; Yampol'skii, V. D.

2014-02-01

Specimens of a 10N3KhDMBF shipbuilding hull steel were clad by a 04Kh20N6G11M2AFB nitrogen austenitic steel using various treatment conditions, which included hot rolling, austenitic facing, and explosive welding followed by hot rolling and heat treatment. Between the base and cladding materials, an intermediate layer with variable concentrations of chromium, manganese, and nickel was found, in which a martensitic structure was formed. In all the cases, the strength of bonding of the cladding layer to the hull steel (determined in tests for shear to fracture) was fairly high (σsh = 437-520 MPa). The only exception was the specimen produced by unidirectional facing without subsequent hot rolling (σsh = 308 MPa), in which nonfusions between the faced beads of stainless steel were detected.

TRIP effect in austenitic-martensitic VNS9-Sh steel at various strain rates

NASA Astrophysics Data System (ADS)

Terent'ev, V. F.; Slizov, A. K.; Prosvirnin, D. V.

2016-10-01

The mechanical properties of austenitic-martensitic VNS9-Sh (23Kh15N5AM3-Sh) steel are studied at a static strain rate from 4.1 × 10-5 to 17 × 10-3 s-1 (0.05-20 mm/min). It is found that, as the strain rate increases, the ultimate tensile strength decreases and the physical yield strength remains unchanged (≈1400 MPa). As the strain rate increases, the yield plateau remains almost unchanged and the relative elongation decreases continuously. Because of high microplastic deformation, the conventional yield strength is lower than the physical yield strength over the entire strain rate range under study. The influence of the TRIP effect on the changes in the mechanical properties of VNS9-Sh steel at various strain rates is discussed.

Fracture behavior of neutron-irradiated high-manganese austenitic steels

NASA Astrophysics Data System (ADS)

Yoshida, H.; Miyata, K.; Narui, M.; Kayano, H.

1991-03-01

The instrumented Charpy impact test was applied to study the fracture behavior of high-manganese austenitic steels before and after neutron irradiations. Quarter-size specimens of a commercial high-manganese steel (18% Mn-5% Ni-16% Cr), three reference steels (21% Mn-1% Ni-9% Cr, 20% Mn-1% Ni-11% Cr, 15% Mn-1% Ni-13% Cr) and two model steels (17% Mn-4.5% Si-6.5% Cr, 22% Mn-4.5% Si-6.5% Cr-0.2% N) were used for the impact tests at temperatures between 77 and 523 K. The load-deflection curves showed typical features corresponding to characteristics of the fracture properties. The temperature dependences of fracture energy and failure deflection obtained from the curves clearly demonstrate only small effects up to 2 × 10 23 n/m 2 ( E > 0.1 MeV) and brittleness at room temperature in 17% Mn-Si-Cr steel at 1.6 × 10 25 n/m 2 ( E > 0.1 MeV), while ductility still remains in 22%Mn-Si-Cr steel.

Influence of the tempering temperature on the mechanical properties and the phase composition of thin sheet TRIP steel

NASA Astrophysics Data System (ADS)

Terent'ev, V. F.; Eliseev, E. A.; Matyunin, V. M.; Slizov, A. K.; Marchenkov, A. Yu.; Sirotinkin, V. P.; Baikin, A. S.; Seval'nev, G. S.

2017-10-01

The strength and the plasticity properties of sheet high-strength austenitic-martensitic VNS9-Sh TRIP steel (23Kh15N5AM3-Sh) are studied as functions of the tempering temperature in the range 125-600°C. A nonmonotonic decease in the strength and the plasticity properties of the steel has been detected when the tempering temperature increases, and they increase in the range 300-450°C. The influence of aging processes, the precipitation of carbide, and the phase transformations in tempering on the mechanical properties of austenitic-martensitic corrosion-resistant steel is discussed.

Microstructural changes in steel 10Kh9V2MFBR during creep for 40000 hours at 600°C

NASA Astrophysics Data System (ADS)

Fedoseeva, A. E.; Kozlov, P. A.; Dudko, V. A.; Skorobogatykh, V. N.; Shchenkova, I. A.; Kaibyshev, R. O.

2015-10-01

In this work, we have investigated microstructural changes in steel 10Kh9V2MFBR (analog of P02 steel) after long-term creep tests at a temperature of 600°C under an initial stress of 137 MPa. Time to rupture was found to be more than 40000 h. It has been established that, in the zone of grips and in the neck region of the sample, the size of the particles of the M 23C6 carbides increases from 85 nm to 152 nm and 182 nm, respectively. In addition, large particles of the Laves phase with an average size of 295 nm are separated. The particles of these phases are located along high-angle boundaries. During prolonged aging and creep, the transformation of the M(C,N) particles enriched in V into the Z phase occurs. The average size of particles of the Z phase after prolonged ageing was 48 nm; after creep, it reached 97 nm. The size of M(C,N) particles enriched by Nb increases from 26 nm after tempering to 55 nm after prolonged aging and creep. It has been established that, in spite of an increase in the transverse size of the laths of tempered martensite from 0.4 to 0.9 µm in the neck of the sample, the misorientation of the lath boundaries does not increase. No recrystallization processes were found to develop in the steel during creep.

Mechanical characteristics and microstructure of weld joint of high-temperature martensitic steel containing 9% Cr

NASA Astrophysics Data System (ADS)

Shakhova, Ya. E.; Belyakov, A. N.; Kaibyshev, R. O.

2016-04-01

The structure and mechanical characteristics of a weld joint of 10Kh9K3V2MFBR steel (0.097 C, 0.17.Si, 0.54 Mn, 8.75 Cr, 0.21 Ni, 0.51 Mo, 0.07 Nb, 0.23 V, 0.004 N, 0.003 B, 1.6 W, 0.15 Cu, and Fe for balance, wt %) have been studied; the joint was produced by hand welding in an argon atmosphere using 03Kh20N45M7G6B welding wire (0.3 C, 20 Cr, 45 Ni, 7 Mo, 6 Mn, and 1 Nb, wt %). The weld joint is divided into the zone of the base metal, a thermal effect zone, which consists of zones that contain fine and coarse original austenitic grains, and the zone of seam metal. It has been shown that the weld joint of 10Kh9K3V2MFBR steel possesses high strength characteristics at the room temperature under static loading and a satisfactorily impact toughness, which has the minimum value of 30 J/cm2 in the zone of the seam metal and does not depend on the temperature. With a decrease in the temperature from the room temperature to 253 K, a ductile-brittle transition occurs in the thermal effect zone. Creep tests carried out at the temperature of 923 K have shown that the long-term strength of the weld seam is lower than that of the base material in the entire stress range being tested. At stresses of 140 MPa or higher, the acceleration of creep in the weld seam is observed, while at low stresses of about 120 MPa, the rates of creep in the weld seam and in the base metal remain similar until the transition to the stage of accelerated fracture occurs. The difference in the values of the long-term strength is due to premature fracture, which occurs in the thermal effect zone with the finegrained structure.

Thermal tests of large recirculation cooling installations for nuclear power plants

NASA Astrophysics Data System (ADS)

Balunov, B. F.; Lychakov, V. D.; Il'in, V. A.; Shcheglov, A. A.; Maslov, O. P.; Rasskazova, N. A.; Rakhimov, R. Z.; Boyarov, R. A.

2017-11-01

The article presents the results from thermal tests of some recirculation installations for cooling air in nuclear power plant premises, including the volume under the containment. The cooling effect in such installations is produced by pumping water through their heat-transfer tubes. Air from the cooled room is blown by a fan through a bundle of transversely finned tubes and is removed to the same room after having been cooled. The finning of tubes used in the tested installations was made of Grade 08Kh18N10T and Grade 08Kh18N10 stainless steels or Grade AD1 aluminum. Steel fins were attached to the tube over their entire length by means of high-frequency welding. Aluminum fins were extruded on a lathe from the external tube sheath into which a steel tube had preliminarily been placed. Although the fin extrusion operation was accompanied by pressing the sheath inner part to the steel tube, tight contact between them over the entire surface was not fully achieved. In view of this, the air gap's thermal resistance coefficient was introduced in calculating the heat transfer between the heat-transferring media. The air gap average thickness was determined from the test results taking into account the gap variation with temperature due to different linear expansion coefficients of steel and aluminum. These tests, which are part of the acceptance tests of the considered installations, were carried out at the NPO TsKTI test facility and were mainly aimed at checking if the obtained thermal characteristics were consistent with the values calculated according to the standard recommendations with introduction, if necessary, of modifications to those recommendations.

Alloying Elements Transition Into the Weld Metal When Using an Inventor Power Source

NASA Astrophysics Data System (ADS)

Mamadaliev, R. A.; Kuskov, V. N.; Popova, A. A.; Valuev, D. V.

2016-04-01

The temperature distribution over the surface of the welded 12Kh18N10T steel plates using the inventor power source ARC-200 has been calculated. In order to imitate multipass welding when conducting the thermal analysis the initial temperature was changed from 298K up to 798K in 100K increments. It has been determined that alloying elements transition into the weld metal depends on temperature. Using an inventor power source facilitates a uniform distribution of alloying elements along the length and height of the weld seam.

Analytical description of changes in the magnetic states of chromium-nickel steel under uniaxial elastic deformation

NASA Astrophysics Data System (ADS)

Gorkunov, E. S.; Yakushenko, E. I.; Zadvorkin, S. M.; Mushnikov, A. N.

2017-12-01

Dependences of magnetization and magnetic permeability of the 15KhN4D structural steel on the value of uniaxial stresses and magnetic field strength are obtained. A polynomial approximation fairly accurately describing the observed changes is proposed on the basis of experimental data.

The Kinetics of Bainitic Transformation of Roll Steel 75Kh3MF

NASA Astrophysics Data System (ADS)

Kletsova, O. A.; Krylova, S. E.; Priymak, E. Yu.; Gryzunov, V. I.; Kamantsev, S. V.

2018-01-01

The critical points of steel 75Kh3MF and the temperature of the start of martensitic transformation are determined by a dilatometric method. The thermokinetic and isothermal diagrams of decomposition of supercooled austenite are plotted. The microstructure and microhardness of steel specimens cooled at different rates are studied. The kinetics of the occurrence of bainitic transformation in the steel is calculated using the Austin-Ricket equation.

Special Features of Induction Annealing of Friction Stir Welded Joints of Medium-Alloy Steels

NASA Astrophysics Data System (ADS)

Priymak, E. Yu.; Stepanchukova, A. V.; Bashirova, E. V.; Fot, A. P.; Firsova, N. V.

2018-01-01

Welded joints of medium-alloy steels XJY750 and 40KhN2MA are studied in the initial condition and after different variants of annealing. Special features of the phase transformations occurring in the welded steels are determined. Optimum modes of annealing are recommended for the studied welded joints of drill pipes, which provide a high level of mechanical properties including the case of impact loading.

Reinvestigation of the Henry's law constant for hydrogen peroxide with temperature and acidity variation.

PubMed

Huang, Daoming; Chen, Zhongming

2010-01-01

Hydrogen peroxide is not only an important oxidant in itself; it also serves as both sink and temporary reservoir for other important oxidants including HOx (OH and HO2) radicals and O3 in the atmosphere. Its partitioning between gas and aqueous phases in the atmosphere, usually described by its Henry's law constant (K(H)), significantly influences its role in atmospheric processes. Large discrepancies between the K(H) values reported in previous work, however, have created uncertainty for atmospheric modelers. Based on our newly developed online instrumentation, we have re-determined the temperature and acidity dependence of K(H) for hydrogen peroxide at an air pressure of (0.960 +/- 0.013) atm (1 atm = 1.01325 x 10(5) Pa). The results indicated that the temperature dependence of K(H) for hydrogen peroxide fits to the Van't Hoff equation form, expressed as lnK(H) = a/T - b, and a = -deltaH/R, where K(H) is in M/atm (M is mol/L), T is in degrees Kelvin, R is the ideal gas constant, and deltaH is the standard heat of solution. For acidity dependence, results demonstrated that the K(H) value of hydrogen peroxide appeared to have no obvious dependence on decreasing pH level (from pH 7 to pH 1). Combining the dependence of both temperature and acidity, the obtained a and b were 7024 +/- 138 and 11.97 +/- 0.48, respectively, deltaH was (58.40 +/- 1.15) kJ/(K x mol), and the uncertainties represent sigma. Our determined K(H) values for hydrogen peroxide will therefore be of great use in atmospheric models.

Thermal conductance of gold plated metallic contacts at liquid helium temperatures

NASA Technical Reports Server (NTRS)

Kittel, Peter; Spivak, Alan L.; Salerno, Louis J.

1992-01-01

The thermal conductance of gold plated OFHC copper, 6061-T6 aluminum, free-machining brass, and 304 stainless steel contacts has been measured over the temperature range of 1.6 to 4.2 K, with applied forces from 22 N to 670 N. The contact surfaces were prepared with a 0.8 micron lapped finish prior to gold coating. It was found that for all materials, except stainless steel, the thermal conductance was significantly improved as the result of gold coating the contact surfaces.

Simulation of Microdamage and Evaluation of Remaining Life of Steam Conduit Components from New-Generation Refractory Steel 10Kh9MF-Sh

NASA Astrophysics Data System (ADS)

Gladshtein, V. I.

2018-03-01

The effects of microdamage on the remaining life of high-temperature components of steam conduits from high-chromium steel 10Kh9MF-Sh and low-alloy steel 12Kh1M1F are compared. To simulate the microdamage, specimens with a circular notch and different relative diameters are fabricated. Specimens with a notch simulating the highest degree of microdamage and smooth specimens are tested for long-term strength. The coefficient of the remaining life of a conduit is computed for the range of relative damage presenting practical interest.

Shielding Requirements for Particle Bed Propulsion Systems.

DTIC Science & Technology

1991-06-01

Heating Rates Rates Rates [W/cc] [W/cc] [W/cc] Hydrogen 11.5 0.09 0.38 Carbon 48 2.2 8.3 Aluminum 80 3.6 14.5 Titanium 335 4.8 36 Stainless Steel 500...12.4 31 Stainless Steel 320 21.5 80 Dose [Rad] Dose [Rad] Dose [Rad] Silicon 4.9e+9 1.36e+5 3.6e 5 The plenum region for these measurements can be...Aluminum (TPA) 0.32 Titanium (TPA) 0.41 Stainless Steel (TPA) 2.3 Dose/Fluence [Rad] / [n/c. 2 ] _ Silicon (TPA/void) 2.4e+4/2.2e+13 The neutron fluence

Elimination of Airborne Lead Contamination from Caliber .22 Ammunition.

DTIC Science & Technology

1987-06-01

R191 365 ELIMINATION OF AIRBORNE LEAD CONTAMINATION FROM CALIBER 1/1 Ri ’ 3 5 22 N INITION(U) ARMY ARMAMENT RESEARCH DE VELOPMENT AM D...E JUNE 1987 U. S. MMW ARKM SRcKH, IDVROPMEff n U COOE US" ARMY EARMLMA CLOSE COMBAT ARMAMENT CENTER - MUNITBONS Et CHEMICAL COMMANDR D RA - A9~laIENT...Command tasked the U.S. Army Armament, Research , Development and Engineering Center (ARDEC) to determine if the sources of lead contamination could be

Rheinheimera salexigens sp. nov., isolated from a fishing hook, and emended description of the genus Rheinheimera.

PubMed

Hayashi, Kazukuni; Busse, Hans-Jürgen; Golke, Jan; Anderson, James; Wan, Xuehua; Hou, Shaobin; Chain, Patrick S G; Prescott, Rebecca D; Donachie, Stuart P

2018-01-01

A Gram-negative, rod-shaped bacterium, designated KH87 T , was isolated from a fishing hook that had been baited and suspended in seawater off O'ahu, Hawai'i. Based on a comparison of 1524 nt of the 16S rRNA gene sequence of strain KH87 T , its nearest neighbours were the GammaproteobacteriaRheinheimera nanhaiensis E407-8 T (96.2 % identity), Rheinheimera chironomi K19414 T (96.0 %), Rheinheimera pacifica KMM 1406 T (95.8 %), Rheinheimera muenzenbergensis E49 T (95.7 %), Alishewanella solinquinati KMK6 T (94.9 %) and Arsukibacterium ikkense GCM72 T (94.6 %). Cells of KH87 T were motile by a single polar flagellum, strictly aerobic, and catalase- and oxidase-positive. Growth occurred between 4 and 39 °C, and in a circumneutral pH range. Major fatty acids in whole cells of strain KH87 T were cis-9-hexadecenoic acid, hexadecanoic acid and cis-11-octadecenoic acid. The quinone system contained mostly menaquinone MK-7, and a minor amount of ubiquinone Q-8. The polar lipid profile contained the major lipids phosphatidylglycerol, phosphatidylserine, phosphatidylethanolamine, an unidentified aminolipid, and a lipid not containing phosphate, an amino group or a sugar moiety. Putrescine was the major polyamine. Physiological, biochemical and genomic data, including obligate halophily, absence of amylolytic activity, a quinone system dominated by MK-7 and DNA G+C content (42.0 mol%) distinguished KH87 T from extant Rheinheimera species; strain KH87 T was also distinguished by a multi-locus sequence analysis of aligned and concatenated 16S rRNA, gyrB, rpoB and rpoD gene sequences. Based on phenotypic and genotypic differences, the species Rheinheimera salexigens sp. nov. is proposed to accommodate KH87 T as the type strain (=ATCC BAA-2715 T =CIP 111115 T ). An emended description of the genus Rheinheimera is also proposed.

The effect of diamond burnishing on structure and properties of detonation-gas coatings on gas-turbine engine parts

NASA Astrophysics Data System (ADS)

Boguslaev, V. A.; Yatsenko, V. K.; Yakovlev, V. G.; Stepanova, L. P.; Pukhal'skaya, G. V.

2008-01-01

A diamond burnishing procedure for detonation coatings made from powder alloys PKKhN-15 and VKNA of parts made of steel Kh12NMBFSh is selected and substantiated, which ensures a favorable combination of the surface layer structure and properties.

The Use of the Maurer Factor for Estimating the Cost of a Turbine Engine in the Early Stages of Development

DTIC Science & Technology

1979-06-01

0-24%) 15-51H AISI 8735-40 17-22A B5F5 301-306 B1112 4O 10 6-321, 347 Chromology0•o5,410 D6ac 416, 420, 431, 440 M50 1010 Carbon Steel Magnesium...Thorium 1074, 1095 Nitrally N135 413o- 4140 S Monel 4340 Wrought 4140 , 464P Wrought Alloy Steel 8630 Vasoojet 1000 9310 A (weighting factor = 6.65--Nickel

Evolution of the structure and the phase composition of a bainitic structural steel during plastic deformation

NASA Astrophysics Data System (ADS)

Nikitina, E. N.; Glezer, A. M.; Ivanov, Yu. F.; Aksenova, K. V.; Gromov, V. E.; Kazimirov, S. A.

2017-10-01

The evolution of the phase composition and the imperfect substructure of the 30Kh2N2MFA bainitic structural steel subjected to compressive deformation by 36% is quantitatively analyzed. It is shown that deformation is accompanied by an increase in the scalar dislocation density, a decrease in the longitudinal fragment sizes, an increase in the number of stress concentrators, the dissolution of cementite particles, and the transformation of retained austenite.

Prime Contract Awards Alphabetically by Contractor, by State or Country, and Place. Part 19 (Swanda Brothers Incorporated-TRT Telecommunications Corp)

DTIC Science & Technology

1990-01-01

0000000000 400c 00) -4000C20 (400000 N44V 010 "- K W Io0-4 Kfc oc a c In00000 i4 00 oo %nw 00 000000 0000 (30 Ji K a 1 0-4 KH00000000000 -W4C4- CD0 anw000...44440444444UUU44444 Kf I W-ONO KIf KfC t -4 -4N K. N K I M-40410 K11 K I 00-4iri4I &, mO &n o In in in in 0 In o inY) )ofIn in in o In In 0 DIn 0oIn In...44444444444444 N44 4 *ON co a 4 .- c) in di n I n t t i i An in t mnam bfIn wi wi wmi wa w) wI In in Infin in in In0 S doaN w4 4’m 113(’ a C) VMmmMV MI

Structural features and properties of the laser-deposited nickel alloy layer on a KhV4F tool steel after heat treatment

NASA Astrophysics Data System (ADS)

Shcherbakov, V. S.; Dikova, Ts. D.; Stavrev, D. S.

2017-07-01

The study and application of the materials that are stable in the temperature range up to 1000°C are necessary to repair forming dies operating in this range. Nickel-based alloys can be used for this purpose. The structural state of a nickel alloy layer deposited onto a KhV4F tool steel and then heat treated is investigated. KhV4F tool steel (RF GOST) samples are subjected to laser deposition using a pulsed Nd:YAG laser. A nickel-based material (0.02C-73.8Ni-2.5Nb-19.5Cr-1.9Fe-2.8Mn) is employed for laser deposition. After laser deposition, the samples are subjected to heat treatment at 400°C for 5 h, 600°C for 1 h, 800°C for 1 h, and 1000°C for 1 h. The microstructure, the phase composition, and the microhardness of the deposited layer are studied. The structure of the initial deposited layer has relatively large grains (20-40 μm in size). The morphology is characterized by a cellular-dendritic structure in the transition zone. The following two structural constituents with a characteristic dendritic structure are revealed: a supersaturated nickel-based γ solid solution and a chromium-based bcc α solid solution. In the initial state and after heat treatment, the hardness of the deposited material (210-240 HV 0.1) is lower than the hardness of the base material (400-440 HV 0.1). Only after heat treatment at 600°C for 1 h, the hardness increases to 240-250 HV0.1. Structure heredity in the form of a dendritic morphology is observed at temperatures of 400, 600, and 800°C. The following sharp change in the structural state is detected upon heat treatment at 1000°C for 1 h: the dendritic morphology changes into a typical α + γ crystalline structure. The hardness of the base material decreases significantly to 160-180 HV 0.1. The low hardness of the deposited layer implies the use of the layer material in limited volume to repair the forming surfaces of dies and molds for die casting. However, the high ductility of the deposited layer of the nickel-based material is a prerequisite for a high stability under thermocycling loading conditions.

Stratospheric Turbulence and Vertical Effective Diffusion Coefficients

DTIC Science & Technology

1975-09-29

UMBER AFCRL-TR-75.-0519 - 4. TILE (moiS."Eti) S. Tlr OF C RP~hT S PESO0 COVERED STRATOSPHERIC TURBULENCE AND VERTICAL EFFECTIVE DIFFUSION COEFFICIENTS...that CAT plays a prominent role in vertical transport in the stratosphere. I ~1 Unclassified t FUrs,*Tv C , Uq C ~ml .. at ’r *n he.. a* U I Department...phenomenon. Thorpe himself refers (1973) to underwater K-H as "underwater CAT." ____ ____ ____WE006 SflJGLE ( SPAD M LAVER 4" Ri" i0 15 0t (m’iJr

Stabilities and partitioning of arenonium ions in aqueous media.

PubMed

Lawlor, D A; More O'Ferrall, R A; Rao, S N

2008-12-31

The phenathrenonium ion is formed as a reactive intermediate in the solvolysis of 9-dichloroacetoxy-9,10-dihydrophenanthrene in aqueous acetonitrile and undergoes competing reactions with water acting as a base and nucleophile. Measurements of product ratios in the presence of azide ion as a trap and 'clock' yield rate constants kp = 3.7 x 10(10) and kH2O = 1.5 x 10(8) s(-1), respectively. Combining these with rate constants for the reverse reactions (protonation of phenanthrene and acid-catalyzed aromatization of its water adduct) gives equilibrium constants pKa = -20.9 and pK(R) = -11.6. For a series of arenonium and benzylic cations, correlation of log kp with pKa, taking account of the limit to kp set by the relaxation of water (10(11) s(-1)), leads to extrapolation of kp = 9.0 x 10(10) s(-1) and pKa = -24.5 for the benzenonium ion and kp = 6.5 x 10(10) s(-1) and pKa = -22.5 for the 1-naphthalenonium ion. Combining these pKa's with estimates of equilibrium constants pKH2O for the hydration of benzene and naphthalene, and the relationship pKR = pKa + pKH2O based on Hess's law, gives pKR = -2.3 and -8.0 respectively, and highlights the inherent stability of the benzenonium ion. A correlation exists between the partitioning ratio, kp/kH2O, for carbocations reacting in water and KH2O the equilibrium constant between the respective reaction products, i.e., log(kp/kH2O) = 0.46pKH2O - 3.7. It implies that kp exceeds kH2O only when KH2O > 10(8). This is consistent with the proton transfer (a) possessing a lower intrinsic reactivity than reaction of the carbocation with water as a nucleophile and (b) being rate-determining in the hydration of alkenes (and dehydration of alcohols) except when the double bond of the alkene is unusually stabilized, as in the case of aromatic molecules.

Roseomonas hibiscisoli sp. nov., isolated from the rhizosphere of Mugunghwa (Hibiscus syriacus).

PubMed

Yan, Zheng-Fei; Lin, Pei; Li, Chang-Tian; Kook, MooChang; Wang, Qi-Jun; Yi, Tae-Hoo

2017-08-01

A Gram-stain-negative, aerobic, non-motile and coccoid to short-rod-shaped bacterial strain (THG-N2.22T) was isolated from the rhizosphere of Mugunghwa (Hibiscus syriacus). Growth occurred at 20-40 °C (optimum 28 °C), at pH 5-9 (optimum 7) and with 0-4 % (w/v) NaCl (optimum 1 %). Based on 16S rRNA gene sequence analysis, the nearest phylogenetic neighbours of strain THG-N2.22T were identified as Roseomonas rhizosphaerae YW11T (98.5 % similarity), Roseomonas rubra S5T (98.5 %), Roseomonas cervicalis ATCC 49957T (98.2 %), Roseomonas aestuarii JC17T (97.8 %), Roseomonas oryzae JC288T (97.3 %) and Roseomonas ludipueritiae 170/96T (97.3 %); levels of similarity with the type strains of other Roseomonas species were lower than 97.0 %. The polar lipids were diphosphatidylglycerol, phosphatidylethanolamine, phosphatidylglycerol, phosphatidylcholine, two unidentified aminolipids, three unidentified phospholipids and three unidentified lipids. The major quinone was ubiquinone-10. The major fatty acids were C16 : 0, C18 : 1 2-OH, C18 : 1ω7c and summed feature 3 (C16 : 1ω7c and/or C16 : 1ω6c). The DNA G+C content of strain THG-N2.22T was 64.1 mol%. DNA-DNA hybridization values between strain THG-N2.22T and R. rhizosphaerae YW11T, R. rubra S5T, R. cervicalis ATCC 49957T, R. aestuarii JC17T, R. oryzae JC288T and R. ludipueritiae 170/96T were 43.1 % (30.2 %, reciprocal analysis), 39.0 % (24.7 %), 34.4 % (15.2 %), 18.0 % (14.5 %), 14.7 % (9.7 %) and 11.0 % (5.6 %), respectively. On the basis of the phylogenetic analysis, chemotaxonomic data, physiological characteristics and DNA-DNA hybridization data, strain THG-N2.22T represents a novel species of the genus Roseomonas, for which the name Roseomonas hibiscisoli sp. nov. is proposed. The type strain is THG-N2.22T (=KACC 18935T=CCTCC AB 2016176T).

Worldwide Crisis Alerting Network, Phase II. Task 2. Identification of Existing Communications Systems,

DTIC Science & Technology

1980-04-01

Pacific Fisher GUUR 1443174 Carrier James Fisher & Sons Pacific Swan GYAB 1440303 Carrier Pacific Nuclear Transport Prins der Nederlanden GYLM 2440601...100 k" III kM 4 10 kz L *O o 1andet 2 182 .S at0 go.t: 2 18 . M 2 112 k H 2411a k~z 210k211 k kNz 223 𔄀’. ":atphnt1, td So0 k.. 5 0 a~ 416 M~ LA ;D...Pd rvk OSkN8. S0 k8 It1 IkNa8e" la ed 2102 kl 2182 kHz 2182 kNZ 2102 kNz 21102 kN$ 2S76 kHz 2 57 kH8 17S? kNj EAST CENTRAL ATLANTIC O aal and SOO kN8 SO

Statistics on Aircraft Gas Turbine Engine Rotor Failures That Occurred in U.S Commercial Aviation During 1988.

DTIC Science & Technology

1992-03-01

1.7 5.1 RB211 384 1.2638 3 0 8 11 2.4 0.0 6.3 8.7 PW2037/2040 192 0.4090 7 1 3 11 17.1 2.4 7.3 26.8 SPEY 860 0.2774 1 1 2 4 63.6 3.6 7.2 14.4 TFE731 ...L382 501D22 T N 3 N 4 S-881017278 MRKA L382 501D22 C N 3 N 3 S-890207092 MRKA L382 501D22 C N 3 N 10 S-880112116 WP15 HS1257 TFE731 T B 7 C 4 S...880211030 EA21 LEAR35 TFE731 T B 7 C 5 S-880411043 EA21 LEAR36 TFE731 T B 7 C 1 S-880628013 EA17 BAE128 TFE731 T B 7 C 4 S-880906154 GL23 FALCON50 TFE731 T B

Aircraft System One-Sixth Scale Model Studies. Coanda/Refraction Noise Suppression Concept. Advanced Development

DTIC Science & Technology

1976-03-01

a 020-/ 6 1- - -J,. I SIDEWALLS I .- .25 THICK STEEL L50 COANDA SURFACE 3 ..16 THICK STEEL 30-INCH RADIUS COANDA SURFACE 38 󈧦k R9 9.00 DIA kt...Kdnsas 67210 REVIEWED BY "_APPROVED BY . 0, I (~ii)Cf I V J COX - Pi, 1i,, t Deur~e Oopart’meni Supe,ntendeni 4ND.NAEC-5215/4 (REV. 3 -70) PLATE NO...Center.Unclassif e Groud 5upoot E u irflet D t 96 3 LR eutN . 083 allard 156r> 74A*C- _ _ _ _ _ _ _ _ _ __ _ _ _ _ _ N , Naervaicyses, aCostics throdn0is aon re

Interrelationship of mechanical and corrosion-mechanical characteristics of type 12KhN4MF steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Voronin, V.P.; Goncharov, A.F.; Maslov, V.A.

1985-11-01

Investigations presented include a comparative evaluation of the corrosionmechanical characteristics of specimens of high-strength chrome-nickelmolybdenum steel taking into consideration the different methods of melting of the original metal. A comparison of the corrosion-mechanical test results obtained with the results of acceptance tests are presented. A study of the fracture surfaces and the specimen material with the use of fractographic, macroscopic, and microscopic analyses is given. The systematization of the corrosion-mechanical test results with the use of methods of mathematical statistics are presented.

Bacteriophage T4D Gene 42 Mutants Exhibit a Defective Genetic Exclusion Phenotype

DTIC Science & Technology

1991-02-01

first noted by Delbruck and Luria (1942) as infection "interference" between various coliphages , was shown by Delbruck and Bailey (1946) to be the...prepare this solution the following were added per liter of distilled deionized water : 5.8 g Na HPO 2 4 3.0 g KH PO , 0.5 g NaCl, 1.0 g NH Cl, and

Coupling Between CTH and LS-DYNA for Thermal Postprocessing: Application to Propellant Cookoff From a Residual Penetrator

DTIC Science & Technology

2006-09-01

1 1 θα θ ∇= ∂ ∂ t ; 1Ω∈x , 0>t (7) and 2 2 2 2 θα θ ∇= ∂ ∂ t ; 2Ω∈x , 0>t , (8) 12 in which α1 and α2 are the thermal diffusivities of steel and...M30A1, respectively. These are defined by p11 1 1 cρ κ α = (9) and p22 2 2 cρ κ α = . (10) Here, κ1 ad κ2 are the thermal conductivities...Coupling Between CTH and LS-DYNA for Thermal Postprocessing: Application to Propellant Cookoff From a Residual Penetrator by Martin N

The effect of chloride ions on the corroded surface layer of 00Cr22Ni5Mo3N duplex stainless steel under cavitation.

PubMed

Wan, Tong; Xiao, Ning; Shen, Hanjie; Yong, Xingyue

2016-11-01

The effects of Cl(-) on the corroded surface layer of 00Cr22Ni5Mo3N duplex stainless steel under cavitation in chloride solutions were investigated using nanoindentation in conjunction with XRD and XPS. The results demonstrate that Cl(-) had a strong effect on the nano-mechanical properties of the corroded surface layer under cavitation, and there was a threshold Cl(-) concentration. Furthermore, a close relationship between the nano-mechanical properties and the cavitation corrosion resistance of 00Cr22Ni5Mo3N duplex stainless steel was observed. The degradation of the nano-mechanical properties of the corroded surface layer was accelerated by the synergistic effect between cavitation erosion and corrosion. A key factor was the adsorption of Cl(-), which caused a preferential dissolution of the ferrous oxides in the passive film layer on the corroded surface layer. Cavitation further promoted the preferential dissolution of the ferrous oxides in the passive film layer. Simultaneously, cavitation accelerated the erosion of the ferrite in the corroded surface layer, resulting in the degradation of the nano-mechanical properties of the corroded surface layer on 00Cr22Ni5Mo3N duplex stainless steel under cavitation. Copyright © 2016. Published by Elsevier B.V.

New data on the kinetics and governing factors of the spall fracture of metals

NASA Astrophysics Data System (ADS)

Kanel, G. I.; Razorenov, S. V.; Garkushin, G. V.; Savinykh, A. S.

2018-01-01

This paper presents two examples of significant departures from usual trends of varying the resistance to spall fracture (spall strength) with changing loading history, load duration and peak shock stress. In experiments with vanadium single crystals we observed an important decrease of spall strength when increasing the shock stress. This was interpreted in terms of disruption of the matter homogeneity as a result of its twinning at shock compression. In experiments with 12Kh18N10T austenitic stainless steel we observed a sharp increase of recorded spall strength value when short load pulses of a triangular profile were replaced by shock pulses of long duration having a trapezoidal shape. This anomaly is associated with formation of the deformation-induced martensitic phase.

Simulated Air Launch Environment. Volume 1

DTIC Science & Technology

1974-10-01

area. The same is true at the aft end where the large steel fairing provides a considerable heat sink. One would, of course, expect similar gradients...111 SZ-110 TZ-51 C0-17 C2-15 C2-16":, T2-17 T2- 15 TZ- 16:’" TZ-1 TZ-2 T2-3 TZ-4 TZ-5 IM H13 N3-44 N3-43 N3-45 T3-44 T3-43 T3-108 S3-104 N3-47 C3-20...Of course, routing of the lead wires must bbe compatible with tooling . 0 The GFE gages used in this program were of poor quality which compromised the

Cumulative Author Index for Soviet Laser Bibliographies Nos. 67-93, September 1983-February 1989

DTIC Science & Technology

1990-02-01

91:62 ABRAHOV A YU 82:30 91:26 92:30 ABAKUOV V N 68:66 73:84 78:82 ABRAMOV 0 I 67:57 72:79 77:46 82:55 86: 15 88:70 ADALIYEV A E 75:9 ABRAHOV 0 V 90...75;68 93:77 ABRAMYAN ’T 0 70:52,72 ABDULLAYEV D A 74:36 ABRAHYAN YE A 70:99 ABDULIAYEV E A 91:25 ABRASIIIN V N 76:54 79:34 81:39 ABDULLAYEV F KH 86...LOYI,; V N S 67:71 91:53 ABSALYAHOVA E KI 87:84 ABDU[JHAIOV I G 90:108 ABSATAROVA N G 93:44 A8DUJL’tANIV R R 71:59 75:82 ABIJBAKIRUV A S 74:30 76:32 90

Microbial Culturomics Broadens Human Vaginal Flora Diversity: Genome Sequence and Description of Prevotella lascolaii sp. nov. Isolated from a Patient with Bacterial Vaginosis.

PubMed

Diop, Khoudia; Diop, Awa; Levasseur, Anthony; Mediannikov, Oleg; Robert, Catherine; Armstrong, Nicholas; Couderc, Carine; Bretelle, Florence; Raoult, Didier; Fournier, Pierre-Edouard; Fenollar, Florence

2018-03-01

Microbial culturomics is a new subfield of postgenomic medicine and omics biotechnology application that has broadened our awareness on bacterial diversity of the human microbiome, including the human vaginal flora bacterial diversity. Using culturomics, a new obligate anaerobic Gram-stain-negative rod-shaped bacterium designated strain khD1 T was isolated in the vagina of a patient with bacterial vaginosis and characterized using taxonogenomics. The most abundant cellular fatty acids were C 15:0 anteiso (36%), C 16:0 (19%), and C 15:0 iso (10%). Based on an analysis of the full-length 16S rRNA gene sequences, phylogenetic analysis showed that the strain khD1 T exhibited 90% sequence similarity with Prevotella loescheii, the phylogenetically closest validated Prevotella species. With 3,763,057 bp length, the genome of strain khD1 T contained (mol%) 48.7 G + C and 3248 predicted genes, including 3194 protein-coding and 54 RNA genes. Given the phenotypical and biochemical characteristic results as well as genome sequencing, strain khD1 T is considered to represent a novel species within the genus Prevotella, for which the name Prevotella lascolaii sp. nov. is proposed. The type strain is khD1 T ( = CSUR P0109, = DSM 101754). These results show that microbial culturomics greatly improves the characterization of the human microbiome repertoire by isolating potential putative new species. Further studies will certainly clarify the microbial mechanisms of pathogenesis of these new microbes and their role in health and disease. Microbial culturomics is an important new addition to the diagnostic medicine toolbox and warrants attention in future medical, global health, and integrative biology postgraduate teaching curricula.

Alpha List of Prime Contract Awards. Oct 91 - Sep 92. FY 92 (Federal Environmental Services - General Hospital Corporation)

DTIC Science & Technology

1993-01-01

4 I COON 4 X- IN IM COO 44 It~ LILA 55 ’)ýl LL - L W I -LLW - UUU-ýý .ý -UL..-- gL lA -40-U- (t’- 0-4-4 N CLIII S O0 I40 0x c> 4Nof-4-.) 05 CI OO 444...000 0- OC C CO C : 1 0-4-4 If 33 33:7 t3::t ;r333333:333r 333 3333: :r --3l3c c 3 c 33 3 :3 ofw 4. I000) i5 55 0 00) it so uC) 11 MM o 00...2Zzzzzz22zzzz2z22Zzzzzzzzzzzzzzz2222 z222zzzz 2 if 1C.)0-4 11 22zzmZZZZZZZZzzzz2zzzz2zz2zzzz~zzzzzzzzz2zz Z 55 C-4(10 II NN N NmJN N N N N :5 -4 1 CO-4NO 51 5 IO W-4NCO 19 it CO-4NCO

The Development of a Droplet Formation and Entrainment Model for Simulations of Immiscible Liquid-Liquid Flows

DTIC Science & Technology

1999-01-01

scale lch and with some constant C2 by 89.02 gchp RilCd ⋅⋅≅ (5.3.13) This was done so that the length scale included in the model...εαα 23 22 12.0 k rrd p RiL < 1.0 Rig < 0.2 K-H Vortices ( ) ( ) 89.022 10.5 gchp Rilrrd ⋅⋅−⋅≅ αα where lch = MIN(δmx

Radio-Astronomical Instruments Observations (Selected Articles),

DTIC Science & Technology

1982-08-02

NL SIIDAUG 82 L I MATVEYENKO, G S MISEZHNIKOV UNCLASSIFIED FTO_ ID(RS) -0564-82 N FTD-ID(RS) T -0564-82 FOREIGN TECHNOLOGY DIVISION RADIO-ASTRONOMICAL...INSTR1ThMNTS OBSERVATIONS (Selected Articles) 3 71982 Approved for public release; LAJ distribuion~ urJA’nited. • I . FTD- ID(RS) T -0564-82 UNEDITED... T , t * r a yy y y 7, u F, f E # Ye, ye; E, e* X x X x Kh, kh X C Zh, zn .4 u L q Ts, ts - -. Z ,. 4 f 14 Ch ,ch U 7 H u I , i w Sh, sh 2 R ia Y, y

75 FR 30377 - Certain Potassium Phosphate Salts from the People's Republic of China: Final Determination of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-01

....7[percnt] phosphorus and 47.3[percnt] potassium. It is generally greater than or equal to 43.0... KH 2 PO 4 . The CAS registry number for MKP is 7778- 77-0. MKP is typically 22.7[percnt] phosphorus... typically 17.8[percnt] phosphorus, 44.8[percnt] potassium and 40[percnt] P 2 O 5 content. DKP is classified...

Improvements in the hydrogen storage properties of the Mg(NH2)2-LiH composite by KOH addition.

PubMed

Amica, G; Enzo, S; Larochette, P Arneodo; Gennari, F C

2018-06-06

Potassium-containing compounds, such as KH, KOH, KNH2 and different potassium halides, have shown positive effects on the dehydrogenation properties of the Li-Mg-N-H system. However, it is still discussed whether the K-compounds modify the thermodynamics of the system or if they have only a catalytic effect. In this work the impact of the addition of two K-containing compounds (0.08 mol% of KCl and KOH) on the hydrogen storage performance of the Mg(NH2)2-LiH composite was studied. The KOH incorporation reduced the dehydrogenation temperature from 197 °C to 154 °C, beginning the process at low temperature (∼70 °C). The doped sample was able to reversibly absorb and desorb 4.6 wt% of hydrogen with improved kinetics; dehydrogenation rates were increased four times, whereas absorptions required 20% less time to be completed in comparison to the pristine material. The thermodynamic destabilization of the Mg(NH2)2-2LiH composite by the addition of a small amount of KOH was demonstrated by an increment of 30% in the dehydrogenation equilibrium pressure. According to detailed structural investigations, the KH formed by the KOH decomposition through milling and thermal treatment, can replace LiH and react with Mg(NH2)2 to produce a mixed potassium-lithium amide (Li3K(NH2)4). The KH role is not limited to catalysis, but rather it is responsible for the thermodynamic destabilization of the Mg(NH2)2-LiH composite and it is actively involved in the dehydrogenation process.

Normothermic and hypothermic models for studying the deleterious effects of hypoxia-reoxygenation on EDHF-mediated relaxation in isolated porcine coronary arteries.

PubMed

Ziberna, Lovro; Lunder, Mojca; Kuzner, Jernej; Drevensek, Gorazd

2009-01-01

The vasomotor response of the coronary artery is altered by hypoxia-reoxygenation (H-R) induced damage. The aim of our study was to compare and evaluate normothermic and hypothermic models which are suitable for future drug studies of vasoprotective action against H-R injury. Porcine coronary arterial rings were isolated and placed in Krebs-Henseleit (K-H) solution. Rings were exposed to normoxic conditions (control group) and two different H-R conditions: the first induced by a 95% N(2)-5% CO(2) gas mixture (40- and 60-min hypoxia) in a normothermic protocol, and the second induced by hypothermic (4 degrees C) hypoxia-reoxygenation in an air-tight beaker filled with K-H solution (24- and 48-hours hypoxia). Reoxygenation was applied by introducing K-H solution aerated with a 95% O(2)-5% CO(2) mixture under normothermic (37 degrees C) conditions. To test the EDHF-mediated relaxation by substance P, rings were first incubated in L-NNA, nitric oxide synthase inhibitor, and indomethacin, cyclooxygenase inhibitor, and then pre-contracted with thromboxane analogue U-46619. Analysis of the maximum relaxation of the arterial rings was performed by one-way ANOVA, followed by Bonferroni's post-test. Distal segments of the coronary artery responded faster to contraction induced by U-46619 and were relaxed by substance P to a greater extent than proximal segments. Maximal relaxations of arterial rings induced by a 10 nM solution of substance P were significantly reduced (p<0.001) from the values for normoxic rings (81.0+/-1.0%, n=30) after 40-min H-R (50.5+/-5.3%, n=30), 60-min H-R (32.1+/-3.5%, n=30), 24-hours hypothermic H-R (56.0+/-2.3%, n=30) and after 48-hours hypothermic H-R (38.5+/-5.1%, n=30). The model employing 40-min normothermic H-R is as effective as 24-hours hypothermic H-R, and 60-min normothermic H-R as 48-hours hypothermic H-R for studying the deleterious effects of H-R on EDHF-mediated relaxation.

Acoustic Studies of Colloidal Suspensions and Marine Sediments. I. Theoretical Considerations and High Frequency Measurements.

DTIC Science & Technology

1980-01-15

coth(KH/2) - 1] (5) 16 Similarly, Hamaker has shown that the potential energy of in- teraction due to van der Waals-London attractive forces between...two flat plates of thickness t is given by AIVA 121r [=H0 (Ho0’+2t)-" (Ho0+t)/z (6 where A is the Hamaker constant for interaction of the particles. It...deflocculation by adsorption of montmorillonite particles. K I1 - 54 - Key to Symbols A Hamaker constant VA attractive energy A area in eq. (44) V

Effect of Cooling Rate and Chemical Composition on Microstructure and Properties of Naturally Cooled Vanadium-Microalloyed Steels

NASA Astrophysics Data System (ADS)

Karmakar, Anish; Sahu, Pooja; Neogy, Suman; Chakrabarti, Debalay; Mitra, Rahul; Mukherjee, Subrata; Kundu, Saurabh

2017-04-01

Samples from two V-microalloyed steels (0.05 wt pct V) having different C and N levels, namely high-C low-N steel, HCLN (0.22 wt pct C, 0.007 wt pct N) and low-C high-N steel, LCHN (0.06 wt pct C, 0.013 wt pct N) were naturally cooled from 1373 K (1100 °C) to room temperature over a range of cooling rates (0.07 to 3.33 K/s). Samples from a plain C-Mn steel (0.06 wt pct C, 0.007 wt pct N) were also subjected to the same heat treatment for comparison. The effect of cooling rate and steel composition on microstructures, precipitates, and tensile properties has been investigated. Due to the presence of large fraction of harder constituents, like pearlite and bainite, HCLN steel showed higher strength and lower ductility than LCHN steel. LCHN steel, on the other hand, showed good combination of strength and ductility due to its predominantly ferrite matrix with precipitation strengthening. The V-precipitate size was more refined and the precipitate density was higher in HCLN steel than that in LCHN steel. This observation confirms the importance of C content in V-microalloyed steel in terms of precipitation strengthening. An intermediate cooling rate ( 1.4 K/s) has been found to be the optimum choice in order to maximize the precipitation strengthening in V-containing steels.

Influence of thermo-mechanical treatment in ferritic phase field on microstructure and mechanical properties of reduced activation ferritic-martensitic steel

NASA Astrophysics Data System (ADS)

Prakash; Vanaja, J.; Laha, K.; Nageswara Rao, G. V. S.

2018-03-01

The present study focuses on the evaluation of microstructure and mechanical properties of reduced activation ferritic-martensitic (RAFM) steel (9Cr-1W-0.06Ta) subjected to thermo-mechanical treatment (TMT) in ferritic phase field. The results obtained were compared with the steel in conventional normalised plus tempered (N+T) condition. The microstructure of the steel in N+T and TMT conditions was assessed by optical and scanning electron microscopes. Hardness, tensile and creep studies were carried out and the results were correlated with the microstructural studies. While the TMT processed steel resulted in coarser prior austenite grains and exhibited ferritic microstructure with large distribution of fine M23C6 and MX precipitates, the N+T steel reveals tempered martensitic structure with finer prior austenitic grains with coarser M23C6 and MX precipitates. Although ferritic structure is present in TMT processed steel, it exhibits better tensile and creep rupture strengths than N+T steel due to the presence of increased dislocation density and finer distribution of precipitates.

Ultrathin g-C3N4 films supported on Attapulgite nanofibers with enhanced photocatalytic performance

NASA Astrophysics Data System (ADS)

Xu, Yongshuai; Zhang, Lili; Yin, Minghui; Xie, Dengyu; Chen, Jiaqi; Yin, Jingzhou; Fu, Yongsheng; Zhao, Pusu; Zhong, Hui; Zhao, Yijiang; Wang, Xin

2018-05-01

A novel visible-light-responsive photocatalyst is fabricated by introducing g-C3N4 ultrathin films onto the surface of attapulgite (ATP) via a simple in-situ depositing technique, in which ATP was pre-grafted using (3-Glycidyloxypropyl) trimethoxysilane (KH560) as the surfactant. A combination of XRD, FT-IR, BET, XPS, UV-vis, TEM and SEM techniques are utilized to characterize the composition, morphology and optical properties of the products. The results show that with the help of KH560, g-C3N4 presented as ultrathin layer is uniformly loaded onto the surface of ATP by forming a new chemical bond (Sisbnd Osbnd C). Comparing with g-C3N4 and ATP, ATP/g-C3N4 exhibits remarkably enhanced visible-light photocatalytic activity in degradation of methyl orange (MO) because of its high surface area, appropriate band gap and the synergistic effect between g-C3N4 and ATP. To achieve the best photocatalyst, the ratio of g-C3N4 was adjusted by controlling the mass portion between ATP-KH560 and melamine (r = m (ATP-KH560)/m (melamine)). The highest decomposition rate of methyl orange (MO) was 96.06% when r = 0.5 and this degradation efficiency remained unchanged after 4 cycles, which is 10 times as that of pure g-C3N4 particles. Possible photocatalytic mechanism is presented.

Biofilm formation by Salmonella spp. in catfish mucus extract under industrial conditions.

PubMed

Dhowlaghar, Nitin; De Abrew Abeysundara, Piumi; Nannapaneni, Ramakrishna; Schilling, Mark W; Chang, Sam; Cheng, Wen-Hsing; Sharma, Chander S

2018-04-01

The objective of this study was to determine the effect of strain and temperature on the growth and biofilm formation of Salmonella spp. in high and low concentrations of catfish mucus extract on different food-contact surfaces at 22 °C and 10 °C. The second objective of this study was to evaluate the efficacy of disinfectants at recommended concentrations and contact times for removing Salmonella biofilms cells on a stainless steel surface containing catfish mucus extract. Growth and biofilm formation of all Salmonella strains increased with higher concentrations of catfish mucus extract at both 10 °C and 22 °C. In 15 μg/ml of catfish mucus extract inoculated with 3 log CFU/ml, the biofilm levels of Salmonella on stainless steel surface reached to 3.5 log CFU/cm 2 at 10 °C or 5.5 log CFU/cm 2 at 22 °C in 7 days. In 375 μg/ml of catfish mucus extract inoculated with 3 log CFU/ml, the biofilm levels of Salmonella on the stainless steel surface reached 4.5 log CFU/cm 2 at 10 °C and 6.5 log CFU/cm 2 at 22 °C in 7 days. No differences were observed between Salmonella strains tested for biofilm formation in catfish mucus extract on the stainless steel surface. The biofilm formation by Salmonella Blockley (7175) in catfish mucus extract was less (P < 0.05) on buna-N rubber when compared to stainless steel, polyethylene and polyurethane surfaces. Salmonella biofilm cells were not detectable on the stainless steel surface after treatment with a mixture of disinfectants but were still present when single compound disinfectants were used. Copyright © 2017 Elsevier Ltd. All rights reserved.

Experimental determination of Henry's law constants of difluoromethane (HFC-32) and the salting-out effects in aqueous salt solutions relevant to seawater

NASA Astrophysics Data System (ADS)

Kutsuna, Shuzo

2017-06-01

Gas-to-water equilibrium coefficients, KeqS (in M atm-1), of difluoromethane (CH2F2), a hydrofluorocarbon refrigerant (HFC-32), in aqueous salt solutions relevant to seawater were determined over a temperature (T) range from 276 to 313 K and a salinity (S) range up to 51 ‰ by means of an inert-gas stripping method. From the van't Hoff equation, the KeqS value in water, which corresponds to the Henry's law constant (KH), at 298 K was determined to be 0.065 M atm-1. The salinity dependence of KeqS (the salting-out effect), ln(KH/KeqS), did not obey the Sechenov equation but was proportional to S0. 5. Overall, the KeqS(T) value was expressed by ln(KeqS(T)) = -49.71 + (77.70 - 0.134 × S0. 5) × (100/T) + 19.14 × ln(T/100). By using this equation in a lower-tropospheric semi-hemisphere (30-90 °S) of the Advanced Global Atmospheric Gases Experiment (AGAGE) 12-box model, we estimated that 1 to 4 % of the atmospheric burden of CH2F2 resided in the ocean mixed layer and that this percentage was at least 4 % in the winter; dissolution of CH2F2 in the ocean may partially influence estimates of CH2F2 emissions from long-term observational data of atmospheric CH2F2 concentrations.

Strain hardening and fracture behavior during tension of directionally solidified high-nitrogen austenitic steel

NASA Astrophysics Data System (ADS)

Maier, Galina; Astafurova, Elena; Melnikov, Eugene; Moskvina, Valentina; Galchenko, Nina

2017-12-01

The effect of grain orientation relative to tensile load on the strain hardening behavior and fracture mechanism of directionally solidified high-nitrogen steel Fe-20Cr-22Mn-1.5V-0.2C-0.6N (in wt %) was studied. The tensile samples oriented along the longitudinal direction of columnar grains demonstrated the improved mechanical properties compared to specimens with the transversal directions of columnar grains: the values of tensile strength and strain-to-fracture were as high as 1080 MPa and 22%, respectively, for tension along the columnar grains and 870 MPa and 11%, respectively, for the tension transversal to the columnar grains. The change in the grain orientation relative to the tensile load varies a fracture mode of the steel. The fraction of the transgranular fracture was higher in the samples with longitudinal directions of the columnar grains compared to the transversal ones.

Effect of hot rolling on the structure and the mechanical properties of nitrogen-bearing austenitic-martensitic 14Kh15AN4M steel

NASA Astrophysics Data System (ADS)

Bannykh, O. A.; Betsofen, S. Ya.; Lukin, E. I.; Blinov, V. M.; Voznesenskaya, N. M.; Tonysheva, O. A.; Blinov, E. V.

2016-04-01

The effect of the rolling temperature and strain on the structure and the properties of corrosionresistant austenitic-martensitic 14Kh15AN4M steel is studied. The steel is shown to exhibit high ductility: upon rolling in the temperature range 700-1100°C at a reduction per pass up to 80%, wedge steel specimens are uniformly deformed along and across the rolling direction without cracking and other surface defects. Subsequent cold treatment and low-temperature tempering ensure a high hardness of the steel (50-56 HRC). Austenite mainly contributes to the hardening upon rolling in the temperature range 700-800°C at a reduction of 50-70%, and martensite makes the main contribution at higher temperatures and lower strains. Texture does not form under the chosen deformation conditions, which indicates dynamic recrystallization with the nucleation and growth of grains having no preferential orientation.

Theoretical Studies of Materials for High-Power Infrared Coatings

DTIC Science & Technology

1975-12-31

occurs when T reaches a value Tf fc 1000 K, as a rough estimate. Setting T = Tf in (8.2) and (8.3) and solving for It gives Itp =- ♦aCjVtra2...r tp « TH (^ Itp = (4KHtpTf/a)(traVaab8) . ^r tp X> TH . 1^5) 2 For the moment it is assumed that o. = 0.1 ffa , and that all...VIII Next consider the ratio < ^ >! /( Itp ),0ns. From (8.4) and (8.5), (VlUs dtp) lOns 3KH(lMs) Cja2 - 7.5 (8.8) where the numerical value

Long-term myocardial preservation: beneficial and additive effects of polarized arrest (Na+-channel blockade), Na+/H+-exchange inhibition, and Na+/K+/2Cl- -cotransport inhibition combined with calcium desensitization.

PubMed

Snabaitis, A K; Chambers, D

1999-11-27

Polarized arrest, induced by tetrodotoxin (TTX) at an optimal concentration of 22 micromol/L, has been shown to reduce ionic imbalance and improve myocardial preservation compared with hyperkalemic (depolarized) arrest. Additional pharmacologic manipulation of ionic changes (involving inhibition of Na+ influx by the Na+/H+ exchanger [HOE694] and Na+/K+/2Cl- cotransporter [furosemide], and calcium desensitization [BDM]) may further improve long-term preservation. In this study, we (i) established optimal concentrations of each drug, (ii) determined additive effects of optimal concentrations of each drug and (iii) compared our optimal preservation solution to an established depolarizing cardioplegia (St Thomas' Hospital solution No 2: STH2) used during long-term hypothermic storage for clinical transplantation. The isolated working rat heart, perfused with Krebs Henseleit (KH) buffer was used; cardiac function was measured after 20 min aerobic working mode perfusion. The hearts (n=6/group) were arrested with a 2 ml infusion (for 30 sec) of the polarizing (control) solution (22 micromol/L TTX in KH) or control+drug and subjected to 5 hr or 8 hr of storage at 7.5 degrees C in the arresting solution. Postischemic function during reperfusion was measured (expressed as percentage of preischemic function). Dose-response studies established optimal concentrations of HOE694 (10 micromol/L), furosemide (1.0 micromol/L) and BDM (30 mmol/L) in the polarizing (control) solution. Sequential addition to the control solution (Group I) of optimal concentrations of HOE694 (Group II), furosemide (Group III), and BDM (Group IV) were compared with STH2 (Group V); postischemic recovery of aortic flow was 29+/-7%, 49+/-6%*, 56+/-2%*, 76+/-3%*, and 25+/-6%, respectively (*P<0.05 vs. I and V). Creatine kinase leakage was lowest, and myocardial ATP content was highest in Group IV. A polarizing preservation solution (KH+TTX) containing HOE694, furosemide, and BDM significantly enhanced long-term preservation compared with an optimized depolarizing solution (STH2) used clinically for long-term donor heart preservation.

Neisseria arctica sp. nov. isolated from nonviable eggs of greater white-fronted geese (Anser albifrons) in Arctic Alaska

USGS Publications Warehouse

Hansen, Cristina M.; Himschoot, Elizabeth; Hare, Rebekah F.; Meixell, Brandt W.; Van Hemert, Caroline R.; Hueffer, Karsten

2017-01-01

During the summers of 2013 and 2014, isolates of a novel Gram-negative coccus in the Neisseria genus were obtained from the contents of nonviable greater white-fronted goose (Anser albifrons) eggs on the Arctic Coastal Plain of Alaska. We used a polyphasic approach to determine whether these isolates represent a novel species. 16S rRNA gene sequences, 23S rRNA gene sequences, and chaperonin 60 gene sequences suggested that these Alaskan isolates are members of a distinct species that is most closely related to Neisseria canis, N. animaloris, and N. shayeganii. Analysis of the rplF gene additionally showed that our isolates are unique and most closely related to N. weaveri. Average nucleotide identity of the whole genome sequence of our type strain was between 71.5% and 74.6% compared to close relatives, further supporting designation as a novel species. Fatty acid methyl ester analysis showed a predominance of C14:0, C16:0, and C16:1ω7c fatty acids. Finally, biochemical characteristics distinguished our isolates from other Neisseria species. The name Neisseria arctica (type strain KH1503T = ATCC TSD-57T = DSM 103136T) is proposed.

Identification of 80K-H as a protein involved in GLUT4 vesicle trafficking

PubMed Central

2005-01-01

PKCζ (protein kinase Cζ) is a serine/threonine protein kinase controlled by insulin, various growth factors and phosphoinositide 3-kinase. It has been implicated in controlling glucose transport in response to insulin by the translocation of GLUT4-(glucose transporter 4) containing vesicles to the plasma membrane in stimulated cells. How PKCζ modulates GLUT4 vesicle trafficking remains unknown. A yeast two-hybrid screen using full-length human PKCζ identified 80K-H protein as an interactor with PKCζ. GST (glutathione S-transferase) pull-down assays with GST-tagged 80K-H constructs confirmed the interaction and showed that the N-terminal portion of 80K-H was not required for the interaction. Immunoprecipitates of endogenous PKCζ from Cho cells, 3T3-L1 adipocytes or L6 myotubes contained endogenous 80K-H, demonstrating a physiological interaction. Insulin stimulation enhanced the association 3–5-fold. Immunoprecipitates of endogenous 80K-H contained endogenous munc18c and immunoprecipitates of endogenous munc18c contained endogenous PKCζ, with insulin markedly increasing the amount of co-immunoprecipitated protein in each case. These results show that insulin triggers interactions in vivo between PKCζ, 80K-H and munc18c. Overexpression of 80K-H constructs mimicked the action of insulin in stimulating both glucose uptake and translocation of Myc-tagged GLUT4 in Cho cells, with the level of effect proportional to the ability of the constructs to associate with munc18c. These results identify 80K-H as a new player involved in GLUT4 vesicle transport and identify a link between a kinase involved in the insulin signalling cascade, PKCζ, and a known component of the GLUT4 vesicle trafficking pathway, munc18c. The results suggest a model whereby insulin triggers the formation of a PKCζ–80K-H–munc18c complex that enhances GLUT4 translocation to the plasma membrane. PMID:15707389

Investigation into the Cyclic Strength of the Bodies of Steam Shutoff Valves from 10Kh9MFB-Sh Steel

NASA Astrophysics Data System (ADS)

Skorobogatykh, V. N.; Kunavin, S. A.; Prudnikov, D. A.; Shchenkova, I. A.; Bazhenov, A. M.; Zadoinyi, V. A.; Starkovskii, G. L.

2018-02-01

Steam shutoff valves are operated under complex loading conditions at thermal and nuclear power stations. In addition to exposure to high temperature and stresses resulting in fatigue, these valves are subjected to cyclic loads in heating-up-cooling down, opening-closing, etc. cycles. The number of these cycles to be specified in designing the valves should not exceed the maximum allowable value. Hence, the problem of cyclic failure rate of steam shutoff valve bodies is critical. This paper continues the previous publications about properties of the construction material for steam shutoff valve bodies (grade 10Kh9MFB-Sh steel) produced by electroslag melting and gives the results of investigation into the cyclic strength of this material. Fatigue curves for the steal used for manufacturing steam shutoff valve bodies are presented. The experimental data are compared with the calculated fatigue curves plotted using the procedures outlined in PNAE G-002-986 and RD 10-249-98. It is confirmed that these procedures may be used in designing valve bodies from 10Kh9MFB-Sh steel. The effect of the cyclic damage after preliminary cyclic loading of the specimens according to the prescribed load conditions on the high-temperature strength of the steel is examined. The influence of cyclic failure rate on the long-term strength was investigated using cylindrical specimens with a smooth working section in the as-made conditions and after two regimes of preliminary cyclic loading (training) at a working temperature of 570°C and the number of load cycles exceeding the design value, which was 2 × 103 cycles. The experiments corroborated that the material (10Kh9MFB-Sh steel) of the body manufactured by the method of electroslag melting had high resistance to cyclic failure rate. No effect of cyclic damages in the metal of the investigated specimens on the high-temperature strength has been found.

Study of the Micro-Nonuniformity of the Plastic Deformation of Steel

NASA Technical Reports Server (NTRS)

Chechulin, B. B.

1957-01-01

The plastic flow during deformation of real polycrystalline metals has specific characteristics which distinguish the plastic deformation of metals from the deformation of ordinary isotropic bodies. One of these characteristics is the marked micro-nonuniformity of the plastic deformation of metals. P.O. Pashkov demonstrated the presence of a considerable micro-nonuniformity of the plastic deformation of coarse-grained steel wit medium or low carbon content. Analogous results in the case of tension of coarse-grained aluminum were obtained by W. Boas, who paid particular attention to the role of the grain boundaries in plastic flow. The nonuniformit of the plastic deformation in microvolumes was also recorded by T.N. Gudkova and others, on the alloy KhN80T. N.F. Lashko pointed out the nonuniformity of the plastic deformation for a series of pure polycrystalline metals and one-phase alloys. In his later reports, P.O. Pashkov arrives at he conclusion that the nonuniformity of the distribution of the deformation along the individual grains has a significant effect on the strength and plastic characteristics of polycrystalline metals in the process of plastic flow. However, until now there has not existed any systematic investigation of the general rules of the microscopic nonuniformit of plastic deformation even though the real polycrystalline metals are extremely simple with regard to structure. In the present report, an attempt is made to study the micrononuniformity of the flow of polycrystalline metals by the method of statistical analysis of the variation of the frequency diagrams of the nonuniformity of the grains in the process of plastic deformation.

The Ground-Level Enhancements of 29 September and 22 October 1989

DTIC Science & Technology

1993-01-01

3409 September 29 OLE Static Zenith Auimuth Thmrahl lwuaae % m~GV -’O0-13:0 . T 130-,,14:00 UT : Mawson 42? N -3 2.5 1.7 42? S -3 2.5 1.7 620 N -5 1.3...seen by all stations except above 2 GV. J is in units of (cm- s ster GV)-. Source direc- Mawson and the second not seen by the low latitude stations...t989 October 22 GLE sun and further studies are continuing. The main GLE was complex with several peaks. We have Time T J J 1, per Source Source

The Effect of Spray Initial Conditions on Heat Release and Emissions in LDI CFD Calculations (Preprint)

DTIC Science & Technology

2008-06-01

Shih, T.-H., Povinelli , L. A., Liu, N.-S and Chen, K.-H., (2000), “Generalized Wall Function for...J. Marek, T. D. Smith, N.-S. Liu, and L. A. Povinelli (NASA, Glenn Research Center, Cleveland, OH, “A Study of Hydrogen/Air Combustor Using NCC

A Thermodynamic Model to Estimate the Formation of Complex Nitrides of Al x Mg(1- x)N in Silicon Steel

NASA Astrophysics Data System (ADS)

Luo, Yan; Zhang, Lifeng; Li, Ming; Sridhar, Seetharaman

2018-06-01

A complex nitride of Al x Mg(1- x)N was observed in silicon steels. A thermodynamic model was developed to predict the ferrite/nitride equilibrium in the Fe-Al-Mg-N alloy system, using published binary solubility products for stoichiometric phases. The model was used to estimate the solubility product of nitride compound, equilibrium ferrite, and nitride compositions, and the amounts of each phase, as a function of steel composition and temperature. In the current model, the molar ratio Al/(Al + Mg) in the complex nitride was great due to the low dissolved magnesium in steel. For a steel containing 0.52 wt pct Als, 10 ppm T.Mg., and 20 ppm T.N. at 1100 K (827 °C), the complex nitride was expressed by Al0.99496Mg0.00504N and the solubility product of this complex nitride was 2.95 × 10-7. In addition, the solution temperature of the complex nitride increased with increasing the nitrogen and aluminum in steel. The good agreement between the prediction and the detected precipitate compositions validated the current model.

An Economic Model of Future Coal/Densified Refuse-Derived Fuel Use at Wright-Patterson AFB, Ohio.

DTIC Science & Technology

1981-09-01

9118 21.5 18.7 27.0 7.5 21 Jul 7845 17.9 23.3 23.5 4.4 22 Jul 9345 18.3 22.2 18.2 15.2 23 Jul 7922 15.9 8.9 19.8 14.0 24 Jul 8177 21.3 18.7 21.2 16.5...40 0 P- 41 40 %0 Ch 0 .) 0 A0 $4 r. UU W - 4 C’f -W .1 H4 IV𔃾 .r44 448 ot (a0 (’ e 4 0 r- :j 4.) r-f t- o: 0n to N .. IU) 4.1 41 N 1 *, tS% H-. to...4J . t 4) 9 1 4 4)0 Ch M oa𔃾 03 Ř A*r04 ’.10 U) o 0 tv 00 .A tn a Ln U1 J Sl:3 to LA 4)r- rz4IL~o-~’.4J $r- ’ 4) -I r. N4 o I~% r ’.~r-4 to * *l * 0

Variation with thermal cycling in microstructure and area specific resistance of a ferritic stainless steel having rough surfaces

NASA Astrophysics Data System (ADS)

Song, Myoung Youp; Mumm, Daniel R.; Song, Jiunn

2013-03-01

Crofer22 APU specimens were prepared by grinding with grit 120 and 400 SiC grinding papers, and were then thermally cycled. The variation in oxidation behavior with thermal cycling was then investigated. Observation of microstructures, measurement of area-specific resistance (ASR), analysis of the atomic percentages of the elements by EDX, and XRD analysis were performed. XRD patterns showed that the (Cr, Mn)3O4 spinel phase grew on the surface of the Crofer22 APU samples ground using grit 120. For the samples ground with grit 400, ASR increased as the number of thermal cycles ( n) increased. Plots of ln (ASR/T) vs. 1/ T for the samples ground with grit 400 after n = 4, 20, and 40 exhibited good linearity, and the apparent activation energies were between 73.4 kJ/mole and 82.5 kJ/mole.

The Mechanism of High Ductility for Novel High-Carbon Quenching-Partitioning-Tempering Martensitic Steel

NASA Astrophysics Data System (ADS)

Qin, Shengwei; Liu, Yu; Hao, Qingguo; Wang, Ying; Chen, Nailu; Zuo, Xunwei; Rong, Yonghua

2015-09-01

In this article, a novel quenching-partitioning-tempering (Q-P-T) process was applied to treat Fe-0.6C-1.5Mn-1.5Si-0.6Cr-0.05Nb hot-rolled high-carbon steel and the microstructures including retained austenite fraction and the average dislocation densities in both martensite and retained austenite were characterized by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy, respectively. The Q-P-T steel exhibits high strength (1950 MPa) and elongation (12.4 pct). Comparing with the steel treated by traditional quenching and tempering (Q&T) process, the mechanism of high ductility for high-carbon Q-P-T steel is revealed as follows. Much more retained austenite existing in Q-P-T steel than in Q&T one remarkably enhances the ductility by the following two effects: the dislocation absorption by retained austenite effect and the transformation-induced plasticity effect. Besides, lower dislocation density in martensite matrix produced by Q-P-T process plays an important role in the improvement of ductility. However, some thin plates of twin-type martensite embedded in dislocation-type martensite matrix in high-carbon Q-P-T steel affect the further improvement of ductility.

Multi-wavelength photometry of the T Tauri binary V582 Mon (KH 15D): A new epoch of occultations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Windemuth, Diana; Herbst, William, E-mail: dwindemuth@wesleyan.edu

2014-01-01

We present multi-wavelength (VRIJHK) observations of KH 15D obtained in 2012/2013, as well as a master table of standard photometry spanning the years 1967 to 2013. The system is a close, eccentric T Tauri binary embedded in an inclined precessing circumbinary (CB) ring. The most recent data show the continued rise of star B with respect to the trailing edge of the occulting horizon as the system's maximum brightness steadily increases. The wealth of data in time and wavelength domains allows us to track the long-term CCD color evolution of KH 15D. We find that the V – I behaviormore » is consistent with direct and scattered light from the composite color of two stars with slightly different temperatures. There is no evidence for any reddening or bluing associated with extinction or scattering by interstellar-medium-size dust grains. Furthermore, we probe the system's faint phase behavior at near-infrared wavelengths in order to investigate extinction properties of the ring and signatures of a possible shepherding planet sometimes invoked to confine the CB ring at ∼5 AU. The wavelength independence of eclipse depth at second contact is consistent with the ring material being fully opaque to 2.2 μm. The color-magnitude diagrams demonstrate excess flux in J and H at low light levels, which may be due to the presence of a hot, young Jupiter-mass planet.« less

Multi-wavelength Photometry of the T Tauri Binary V582 Mon (KH 15D): a New Epoch of Occultations

NASA Astrophysics Data System (ADS)

Windemuth, Diana; Herbst, William

2014-01-01

We present multi-wavelength (VRIJHK) observations of KH 15D obtained in 2012/2013, as well as a master table of standard photometry spanning the years 1967 to 2013. The system is a close, eccentric T Tauri binary embedded in an inclined precessing circumbinary (CB) ring. The most recent data show the continued rise of star B with respect to the trailing edge of the occulting horizon as the system's maximum brightness steadily increases. The wealth of data in time and wavelength domains allows us to track the long-term CCD color evolution of KH 15D. We find that the V - I behavior is consistent with direct and scattered light from the composite color of two stars with slightly different temperatures. There is no evidence for any reddening or bluing associated with extinction or scattering by interstellar-medium-size dust grains. Furthermore, we probe the system's faint phase behavior at near-infrared wavelengths in order to investigate extinction properties of the ring and signatures of a possible shepherding planet sometimes invoked to confine the CB ring at ~5 AU. The wavelength independence of eclipse depth at second contact is consistent with the ring material being fully opaque to 2.2 μm. The color-magnitude diagrams demonstrate excess flux in J and H at low light levels, which may be due to the presence of a hot, young Jupiter-mass planet.

Prime Contractors with Awards Over $25,000 by Name, Location, and Contract Number, Fiscal Year 87. Part 12. United Steel & Wire Company-Zynar, Incorporated.

DTIC Science & Technology

1987-01-01

00 Z C. 4 9 > > t ’r z> >> > > > > I Z C0 0 K r . 50 F580 0 9000 > >> > > >> > > > 4444 Cd~dd > IL . *’% IP ~ ~ V -,~.: :<~ ID O* 0040C\\ t- O O1’INMN N...04 - CC 00 0 .4L 00000 . Ze) L) Sz0 Z3 :333 0%3 : m U3 0.w Ip w ? L) s u H U 0 7 Z 7- u cc 5 m 00 w~ > I w~ : < en 20 WI CW m : ) A e u0 000 00 WLLSW...ON a’ OD 0.0V .. N-0 t- 0 N 0DM a 0 4 N cc r0!0 w . Vw w w mw0wwm wc V m 0 0~. .0 0 0) Voz . Nw( g-) 00 m 1 0c 0 C00 00 N 0-Mm0mV 0 0 0 -Cmm e) 0 - V f

Behavior of lateral-deformation coefficients during elastoplastic deformation of metals

NASA Astrophysics Data System (ADS)

Zimin, B. A.; Smirnov, I. V.; Sudenkov, Yu. V.

2017-06-01

The results of investigations into variation of the coefficients of lateral deformation (the Poisson ratio) during single-axis tension of samples of steel 12Kh18N10T and St3, titanium VT1, the aluminum alloy D16AM, copper M1, and a magnesium alloy are considered. The technique developed on the basis of the optoacoustic effect and simultaneous measurements of the longitudinal and surface speeds of sound in metallic samples during the tension makes it possible to measure the rates at various stages of the deformation process. The data obtained make it possible to construct the dependences of variation of the lateral-deformation coefficients at all stages of the plastic flow. The correlation of these variations both with known processes of structural reconstructions at various stages of plastic flow and with the process of localization of plastic-shear bands in the aluminum alloy is noted.

The Renewal Equation for Markov Renewal Processes with Applications to Storage Models.

DTIC Science & Technology

1986-05-01

2.21) = pt(Bf(jO,A))v(EO, tD )+I(6=O)[:P(YnkB,T nkTnkk~t’Ynk-kiY) -2pO(Bn(j0 ,A))v([O,tJ3 if ye (j09A), with p, v as in corollary 2.2, and y and 6 are...S.) max ( max (S n-S )+(S n-S n 0~. l 5j:n no 0 14_XM nk -n: j!nk 0kI n n Thus, for all w 4EA, Z (wlmax( max (S -S.),x +S 1=0. (3.4) l,n 0 1j n 0

Patch test reactivity to a cobalt-chromium-molybdenum alloy and stainless steel in metal-allergic patients in correlation to the metal ion release.

PubMed

Summer, Burkhard; Fink, Ulrich; Zeller, Richard; Rueff, Franziska; Maier, Sonja; Roider, Gabriele; Thomas, Peter

2007-07-01

Nickel, chromium, and cobalt released from stainless steel and CoCrMo alloys have been postulated to trigger hypersensitivity reactions. The objective of this study was to assess the ion release from a CoCrMo alloy and stainless steel in vitro and the cutaneous reactivity to it by patch test. 52 metal-allergic patients and 48 non-allergic controls were patch tested to stainless steel and CoCrMo discs. In addition, using atomic absorption spectrometry, the release of nickel, cobalt, and chromium from both materials was assessed upon 2-day exposure to distilled water, artificial sweat (AS), and cell culture medium. There was low nickel ion release from stainless steel (0.3-0.46 microg/cm(2)/2 days) and CoCrMo discs (up to 0.33 microg/cm(2)/2 days) into the different elution media. Chromium release from the 2 materials was also very low (0.06-0.38 microg/cm(2)/2 days from stainless steel and 0.52-1.36 microg/cm(2)/2 days from CoCrMo alloy). In contrast, AS led to abundant cobalt release (maximally 18.94 microg/cm(2)/2 days) from the CoCrMo discs, with concomitant eczematous reaction upon patch testing: 0 of the 52 metal-allergic patients reacted to stainless steel discs and 5 of the 52 patients to CoCrMo discs (all 5 patients were cobalt allergic and 3 also nickel and chromium allergic). None of the controls reacted to the discs. Apart from nickel being a focus of allergological research, our results point to the possibly underestimated association of cobalt release and potential hyperreactivity to CoCrMo alloy.

INVESTIGATION OF THE HUMIDITY EFFECT ON THE FAC-IR-300 IONIZATION CHAMBER RESPONSE.

PubMed

Mohammadi, Seyed Mostafa; Tavakoli-Anbaran, Hossein

2018-02-01

The free-air ionization chamber is communicating with the ambient air, therefore, the atmospheric parameters such as temperature, pressure and humidity effect on the ionization chamber performance. The free-air ionization chamber, entitled as FAC-IR-300, that design at the Atomic Energy Organization of Iran, AEOI, is required the atmospheric correction factors for correct the chamber reading. In this article, the effect of humidity on the ionization chamber response was investigated. For this reason, was introduced the humidity correction factor, kh. In this article, the Monte Carlo simulation was used to determine the kh factor. The simulation results show in relative humidities between 30% to 80%, the kh factor is equal 0.9970 at 20°C and 0.9975 at 22°C. From the simulation results, at low energy the energy dependence of the kh factor is significant and with increasing energy this dependence is negligible. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Genetic Exclusion in Bacteriophage T4.

DTIC Science & Technology

1987-01-01

1942) as "interference" between various coliphages , was shown by Delbruck and Bailey (1946) to be the inability of superinfecting phage to contribute... water : 5.8 g Na IPO , 3.0 2 4 g KH PO , 0.5 g NaCl, 1.0 g NH Cl, and the pH adjusted to 2 4 4 o 6.8 to 7.0. All media were autoclaved, cooled to 55 C...0.5M Tris), once with a 1:1 mixture of phenol and chloroform (1/24 isoamyl alcohol) then thrice iith an equal volume of water saturated ether. After

Restoration of Spermatogenesis Using a New Combined Herbal Formula of Epimedium koreanum Nakai and Angelica gigas Nakai in an Luteinizing Hormone-Releasing Hormone Agonist-Induced Rat Model of Male Infertility

PubMed Central

2017-01-01

Purpose We investigated the protective effect of a mixture of 2 herbal extracts, KH-465, which consisted of Epimedium koreanum Nakai and Angelica gigas Nakai, on spermatogenesis in a luteinizing hormone-releasing hormone (LHRH) agonist-induced rat model of male infertility. Materials and Methods Seventy-five 12-week-old male Sprague-Dawley rats were randomly divided into 5 groups, containing 15 rats each: a normal control group that received no treatment and 4 experimental groups (I, II, III, and IV) in which an LHRH agonist was administered for 4 weeks to induce spermatogenic failure. Group I received distilled water, and groups II, III, and IV received 200 mg/kg/day of KH-465, 400 mg/kg/day KH-465, and depo-testosterone for 4 weeks, respectively. Weight changes of the testis and epididymis, sperm count motility, and levels of testosterone (T), free T, follicle-stimulating hormone (FSH), luteinizing hormone (LH), superoxide dismutase (SOD), and 8-hydroxy-2′-deoxyguanosine (8-OHdG) were estimated. Results Body, testis, and epididymis weight showed no significant differences among the control and experimental groups. Treatment with KH-465 increased the sperm count and motility. Serum hormone levels of T, free T, and FSH were not significantly different in the experimental groups, while the LH level was higher than in the LHRH agonist-induced control group, but not to a significant extent. Levels of SOD were higher and 8-OHdG were lower in the groups that received KH-465 than in the LHRH agonist-induced control group. Conclusions Our results suggest that KH-465 increased sperm production via reducing oxidative stress and had a positive effect in a male infertility model. PMID:29076302

Effects of cooling time and alloying elements on the microstructure of the gleeble-simulated heat-affected zone of 22% Cr duplex stainless steels

NASA Astrophysics Data System (ADS)

Hsieh, Rong-Iuan; Liou, Horng-Yih; Pan, Yeong-Tsuen

2001-10-01

The effects of austenite stabilizers, such as nitrogen, nickel, and manganese, and cooling time on the microstructure of the Gleeble simulated heat-affected zone (HAZ) of 22% Cr duplex stainless steels were investigated. The submerged are welding was performed for comparison purposes. Optical microscopy (OM) and transmission electron microscopy (TEM) were used for microscopic studies. The amount of Cr2N precipitates in the simulated HAZ was determined using the potentiostatic electrolysis method. The experimental results indicate that an increase in the nitrogen and nickel contents raised the δ to transformation temperature and also markedly increased the amount of austenite in the HAZ. The lengthened cooling time promotes the reformation of austenite. An increase in the austenite content reduces the supersaturation of nitrogen in ferrite matrix as well as the precipitation tendency of Cr2N. The optimum cooling time from 800 to 500 °C (Δ t 8/5) obtained from the Gleeble simulation is between 30 and 60 s, which ensures the austenite content in HAZ not falling below 25% and superior pitting and stress corrosion cracking resistance for the steels. The effect of manganese on the formation of austenite can be negligible.

The Structure and Mechanical Properties of Ni-Mo PM Steels with Addition of Mn And Cu

NASA Astrophysics Data System (ADS)

Lichańska, E.; Kulecki, P.; Pańcikiewicz, K.

2017-12-01

The aim of the study was to evaluate the effect of chemical composition on the structure and mechanical properties of Mn-Ni-Mo and Ni-Mo-Cu PM steels. Pre-alloyed powder Astaloy 85Mo, diffusion alloyed powders Distaloy AQ and Distaloy AB produced by Höganäs, low carbon ferromanganese, carbonyl nickel powder T255 with three-dimensional filamentary structure and graphite CU-F have been used as the basic powders. Three mixtures with compositions of Fe-1%Mn-(0.5/1.75)%Ni-(0.5/0.85)%Mo-0.8%C and Fe-1.75%Ni-0.5%Mo-1.5%Cu-0.8%C were prepared in a Turbula mixer. Green compacts were single pressed in a steel die at 660 MPa according to PN-EN ISO 2740 standard. Sinterhardening was carried out at 1250°C in a mixture of 95% N2+5% H2 for 60 minutes. Mechanical tests (tensile, bend, hardness) and microstructural investigations were performed. Additionally, XRD and EDS analysis, fractographic investigations were carried out. The microstructures of steels investigated were mainly bainitic or bainitic-martensitic. Addition 1% Mn to Distaloy AQ based steel caused increase of tensile properties (YS from 422 to 489 MPa, UTS from 522 to 638 MPa, TRS from 901 to 1096 MPa) and decrease of plasticity (elongation from 3.65 to 2.84%).

Inhibition of Mild Steel Corrosion in Hydrochloric Acid Solution by New Coumarin

PubMed Central

Kadhum, Abdul Amir H.; Mohamad, Abu Bakar; Hammed, Leiqaa A.; Al-Amiery, Ahmed A.; San, Ng Hooi; Musa, Ahmed Y.

2014-01-01

A new coumarin derivative, N,N′-((2E,2′E)-2,2′-(1,4-phenylenebis(methanylylidene))bis(hydrazinecarbonothioyl))bis(2-oxo-2H-chromene-3-carboxamide) PMBH, was synthesized and its chemical structure was elucidated and confirmed using spectroscopic techniques (Infrared spectroscopy IR, Proton nuclear magnetic resonance, 1H-NMR and carbon-13 nuclear magnetic resonance 13C-NMR). The corrosion inhibition effect of PMBH on mild steel in 1.0 M HCl was investigated using corrosion potential (ECORR), potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), and electrochemical frequency modulation (EFM) measurements. The obtained results indicated that PMBH has promising inhibitive effects on the corrosion of mild steel in 1.0 M HCl across all of the conditions examined. Scanning electron microscopy (SEM) was used to investigate the morphology of the mild steel before and after immersion in 1.0 M HCl solution containing 0.5 mM of PMBH. Surface analysis revealed improvement of corrosion resistance in presence of PMBH. PMID:28788680

Killing Effects of an Isolated Serratia marcescens KH-001 on Diaphorina citri via Lowering the Endosymbiont Numbers

PubMed Central

Hu, Wei; Kuang, Fan; Lu, Zhanjun; Zhang, Ning; Chen, Tingtao

2018-01-01

Huanglongbing (HLB) is the most devastating citrus disease worldwide, and suppression of the Asian citrus psyllid (Diaphorina citri) is regarded as an effective method to inhibit the spread of HLB. In this study, we isolated a strain named as Serratia marcescens KH-001 from D. citri nymphs suffering from disease, and evaluated its killing effect on D. citri via toxicity test and effect on microbial community in D. citri using high-throughput sequencing. Our results indicated that S. marcescens KH-001 could effectively kill 83% of D. citri nymphs, while the fermentation products of S. marcescens KH-001 only killed 40% of the D. citrinymphs. High-throughput sequencing results indicated that the S. marcescens KH-001 increased the OTU numbers from 62.5 (PBS buffer) to 81.5, while significantly lowered the Shannon index compared with Escherichia coli DH5α (group E) (p < 0.05). OTU analysis showed that the S. marcescens KH-001 had significantly reduced the relative abundance of endosymbionts Wolbachia, Profftella, and Carsonella in group S compared with that in other groups (p < 0.05). Therefore, the direct killing effect of the fermentation products of S. marcescens KH-001 and the indirect effect via reducing the numbers of endosymbionts (Wolbachia, Profftella, and Carsonella) of D. citri endow S. marcescens KH-001 a sound killing effect on D. citri. Further work need to do before this strain is used as a sound biological control agents. PMID:29765368

Killing Effects of an Isolated Serratia marcescens KH-001 on Diaphorina citri via Lowering the Endosymbiont Numbers.

PubMed

Hu, Wei; Kuang, Fan; Lu, Zhanjun; Zhang, Ning; Chen, Tingtao

2018-01-01

Huanglongbing (HLB) is the most devastating citrus disease worldwide, and suppression of the Asian citrus psyllid ( Diaphorina citri ) is regarded as an effective method to inhibit the spread of HLB. In this study, we isolated a strain named as Serratia marcescens KH-001 from D. citri nymphs suffering from disease, and evaluated its killing effect on D. citri via toxicity test and effect on microbial community in D. citri using high-throughput sequencing. Our results indicated that S. marcescens KH-001 could effectively kill 83% of D. citri nymphs, while the fermentation products of S. marcescens KH-001 only killed 40% of the D. citri nymphs. High-throughput sequencing results indicated that the S. marcescens KH-001 increased the OTU numbers from 62.5 (PBS buffer) to 81.5, while significantly lowered the Shannon index compared with Escherichia coli DH5α (group E) ( p < 0.05). OTU analysis showed that the S. marcescens KH-001 had significantly reduced the relative abundance of endosymbionts Wolbachia , Profftella , and Carsonella in group S compared with that in other groups ( p < 0.05). Therefore, the direct killing effect of the fermentation products of S. marcescens KH-001 and the indirect effect via reducing the numbers of endosymbionts ( Wolbachia , Profftella , and Carsonella ) of D. citri endow S. marcescens KH-001 a sound killing effect on D. citri . Further work need to do before this strain is used as a sound biological control agents.

Postpartum immobilization of adult female moose using xylazine, ketamine and yohimbine hydrochlorides.

PubMed

Garner, D L; Addison, E M

1994-01-01

Twenty-two free-ranging adult female moose (Alces alces) were immobilized with a 1:4 mixture of xylazine hydrochloride (XH) and ketamine hydrochloride (KH). Mean (SD) dosages/animal for XH and KH were 419 (148) and 1565 (433) mg, respectively. Mean (SD) induction time was 18.4 (9.7) minutes. Reversal with yohimbine hydrochloride using a mean dosage of 83 mg/animal resulted in a mean (SD) recovery time of 22.8 (28.5) minutes.

Velocity shear Kelvin-Helmholtz instability with inhomogeneous DC electric field in the magnetosphere of Saturn

NASA Astrophysics Data System (ADS)

Kandpal, Praveen; Kaur, Rajbir; Pandey, R. S.

2018-01-01

In this paper parallel flow velocity shear Kelvin-Helmholtz instability has been studied in two different extended regions of the inner magnetosphere of Saturn. The method of the characteristic solution and kinetic approach has been used in the mathematical calculation of dispersion relation and growth rate of K-H waves. Effect of magnetic field (B), inhomogeneity (P/a), velocity shear scale length (Ai), temperature anisotropy (T⊥ /T||), electric field (E), ratio of electron to ion temperature (Te /Ti), density gradient (εnρi) and angle of propagation (θ) on the dimensionless growth rate of K-H waves in the inner magnetosphere of Saturn has been observed with respect to k⊥ρi . Calculations of this theoretical analysis have been done taking the data from the Cassini in the inner magnetosphere of Saturn in the two extended regions of Rs ∼4.60-4.01 and Rs ∼4.82-5.0. In our study velocity shear, temperature anisotropy and magnitude of the electric field are observed to be the major sources of free energy for the K-H instability in both the regions considered. The inhomogeneity of electric field, electron-ion temperature ratio, and density gradient have been observed playing stabilizing effect on K-H instability. This study also indicates the effect of the vicinity of icy moon Enceladus on the growth of K-H instability.

Hell-Bent on Force Protection: Confusing Troop Welfare With Mission Accomplishment in Counterinsurgency

DTIC Science & Technology

2009-01-01

embrace the tactical risks necessary for operational and strategic success. It is time to put our money where our mouth is, steel ourselves for the...to embrace the tactical risks necessary for operational and strategic success. It is time to put our money where our mouth is, steel ourselves for t...http://www.nytimes.com/2009/0]/22/world/asia/22taliban.html? fta =y (accessed February 26, 2009). , Foot , Richard. "Deadly lED Tactics Honed in Iraq

Structure-activity relationship studies and pharmacological characterization of N5-heteroarylalkyl-substituted-2-(2-furanyl)thiazolo[5,4-d]pyrimidine-5,7-diamine-based derivatives as inverse agonists at human A2A adenosine receptor.

PubMed

Varano, Flavia; Catarzi, Daniela; Vincenzi, Fabrizio; Falsini, Matteo; Pasquini, Silvia; Borea, Pier Andrea; Colotta, Vittoria; Varani, Katia

2018-06-09

This paper describes the synthesis and characterization of N 5 -(hetero)arylalkyl-substituted-thiazolo [5,4-d]pyrimidine-5,7-diamine derivatives (4-19) as novel human (h) A 2A adenosine receptor (AR) inverse agonists. Competition binding and cyclic AMP assays indicate that the examined compounds behave as hA 2A AR inverse agonists showing binding affinity values in the nanomolar or subnanomolar range. Notably, compounds 4, 5, 6 and 11 showed two affinity values for the hA 2A ARs with the highest (KH) falling in the femtomolar range and the lowest (KL) of the nanomolar order. In addition, in cyclic AMP assays, compounds 4, 5, 6 and 11 exhibited potency (IC 50 ) values in the picomolar range. This study has confirmed that 2-(2-furanyl)thiazolo [5,4-d]pyrimidine-5,7-diamine-based derivatives represent a unique new class of hA 2A AR inverse agonists. Copyright © 2018 Elsevier Masson SAS. All rights reserved.

Substorms, Plasmoids, Flux Robes, and Magnetotail Flux Loss on March 25, 1983: CDAW-8

DTIC Science & Technology

1988-10-03

1400 UT. The magnitude and orientation of the 11 GOES 5 OR 1982-01 9A SE14 14 ZSM -l1ORe ISEE 3 -10 -5 5 OReYSM YS m ISEE 1 5 14r- -* IMP 8 0 Fig. lb...and references therein]. ISEE 1 saw a 31% field decrease from 55 nT to 38 nT between 1020 and 1058 UT, and a 35 % decrease from 62 nT to 41 nT between...strength is determined by the component 29 2.5 POLAR CAP AREA 2.0 E ISEE 1 . 5 -i 60 x - 50 IMP 8 - 40 35 ISEE-3 (B = 22nt) 30 25 ISE IMP8 cc" Z u

Kinetics of the oxidation of hydrogen sulfite by hydrogen peroxide in aqueous solution:. ionic strength effects and temperature dependence

NASA Astrophysics Data System (ADS)

Maaß, Frank; Elias, Horst; Wannowius, Klaus J.

Conductometry was used to study the kinetics of the oxidation of hydrogen sulfite, HSO -3, by hydrogen peroxide in aqueous non-buffered solution at the low concentration level of 10 -5-10 -6 M, typically found in cloud water. The kinetic data confirm that the rate law reported for the pH range 3-6 at higher concentration levels, rate= kH·[H +]·[HSO -3]·[H 2O 2], is valid at the low concentration level and at low ionic strength Ic. At 298 K and Ic=1.5×10 -4 M, third-order rate constant kH was found to be kH=(9.1±0.5)×10 7 M -2 s -1. The temperature dependence of kH led to an activation energy of Ea=29.7±0.9 kJ mol -1. The effect of the ionic strength (adjusted with NaCl) on rate constant kH was studied in the range Ic=2×10 -4-5.0 M at pH=4.5-5.2 by conductometry and stopped-flow spectrophotometry. The dependence of kH on Ic can be described with a semi-empirical relationship, which is useful for the purpose of comparison and extrapolation. The kinetic data obtained are critically compared with those reported earlier.

Updated atmospheric speciated mercury emissions from iron and steel production in China during 2000-2015

NASA Astrophysics Data System (ADS)

Wu, Qingru; Gao, Wei; Wang, Shuxiao; Hao, Jiming

2017-09-01

Iron and steel production (ISP) is one of the significant atmospheric Hg emission sources in China. Atmospheric mercury (Hg) emissions from ISP during 2000-2015 were estimated by using a technology-based emission factor method. To support the application of this method, databases of Hg concentrations in raw materials, technology development trends, and Hg removal efficiencies of air pollution control devices (APCDs) were constructed through national sampling and literature review. Hg input to ISP increased from 21.6 t in 2000 to 94.5 t in 2015. In the various types of raw materials, coking coal and iron concentrates contributed 35-46 and 25-32 % of the total Hg input. Atmospheric Hg emissions from ISP increased from 11.5 t in 2000 to 32.7 t in 2015 with a peak of 35.6 t in 2013. Pollution control promoted the increase in average Hg removal efficiency, from 47 % in 2000 to 65 % in 2015. During the study period, sinter/pellet plants and blast furnaces were the largest two emission processes. However, emissions from roasting plants and coke ovens cannot be ignored, which accounted for 22-34 % of ISP's emissions. Overall, Hg speciation shifted from 50/44/6 (gaseous elemental Hg (Hg0)/gaseous oxidized Hg (HgII)/particulate-bound Hg (Hgp)) in 2000 to 40/59/1 in 2015, which indicated a higher proportion of Hg deposition around the emission points. Future emissions of ISP were expected to decrease based on the comprehensive consideration crude-steel production, steel scrap utilization, energy saving, and pollution control measures.

[Effect of KH2PO4 on the odonto- and osteogenic differentiation potential of human stem cells from apical papillae].

PubMed

Wang, Yan-ping; Wu, Jin-tao; Wang, Zi-lu; Zheng, Yang-yu; Zhang, Guang-dong; Yu, Jin-hua

2013-01-01

To determine the effects of KH2PO4 on the odonto- and osteogenic differentiation potential of human stem cells from apical papillae (SCAP) in vitro. SCAP were isolated and cultured respectively in alpha minimum essential medium (α-MEM) or α-MEM containing 1.8 mmol/L KH2PO4. Alkaline phosphatase (ALP) activity, alizarin red staining, real-time reverse transcription polymerase chain reaction (RT-PCR) and Western blotting were used to examine the odonto and osteogenic potential of SCAP in the two media. SCAP cultured in α-MEM containing 1.8 mmol/L KH2PO4 exhibited a higher ALP activity [(0.370 ± 0.013) Sigma unit×min(-1)×mg(-1)] at day 3 than control group [(0.285 ± 0.008) Sigma unit×min(-1)×mg(-1)] and KH2PO4-treated SCAP formed more calcified nodules at day 5 [(0.539 ± 0.007) µg/g] and day 7 [(1.617 ± 0.042) µg/g] than those in normal medium [(0.138 ± 0.037) µg/g, P < 0.01]. The expression of odonto- and osteogenic markers were significantly up-regulated after the stimulation of KH2PO4 at day 3 and 7 respectively, as compared with control group. 1.8 mmol/L KH2PO4 can promote the odonto and osteogenic differentiation potential of human SCAP.

Enhanced Inactivation of Salmonella and Pseudomonas Biofilms on Stainless Steel by Use of T-128, a Fresh-Produce Washing Aid, in Chlorinated Wash Solutions

PubMed Central

Shen, Cangliang; Luo, Yaguang; Nou, Xiangwu; Bauchan, Gary; Zhou, Bin; Wang, Qin

2012-01-01

The effect of the washing aid T-128 (generally recognized as safe [GRAS] formulation, composed mainly of phosphoric acid and propylene glycol) on inactivation of Salmonella and Pseudomonas populations in biofilms on stainless steel was evaluated under conditions of increasing organic matter loads in chlorinated wash solutions dominated by hypochlorous acid. Biofilms were formed statically on stainless steel coupons suspended in 2% lettuce extract after inoculation with Salmonella enterica serovar Thompson or Newport or with Pseudomonas fluorescens. Coupons with biofilms were washed in chlorine solutions (0, 0.5, 1, 2, 5, 10, or 20 mg/liter at pH 6.5, 5.0 and 2.9), with or without T-128, and with increasing loads of organic matter (0, 0.25, 0.5, 0.75, or 1.0% lettuce extract). Cell populations on coupons were dispersed using intermittent, pulsed ultrasonication and vortexing and enumerated by colony counts on XLT-4 or Pseudomonas agars. Cell responses to fluorescent viability staining of biofilm treatment washing solutions were examined using confocal laser scanning microscopy. Results showed that 0.1% T-128 (without chlorine) reduced P. fluorescens biofilm populations by 2.5 log10 units but did not reduce Salmonella populations. For both Salmonella and Pseudomonas, the sanitizing effect of free chlorine (1.0 to 5.0 mg/liter) was enhanced (P < 0.05) when it was combined with T-128. Application of T-128 decreased the free chlorine depletion rate caused by increasing organic matter in wash waters and significantly (P < 0.05) augmented inactivation of bacteria in biofilms compared to treatments without T-128. Image analysis of surfaces stained with SYTO and propidium iodide corroborate the cultural assay results showing that T-128 can aid in reducing pathogen viability in biofilms and thus can aid in sanitizing stainless steel contact surfaces during processing of fresh-cut produce. PMID:22752180

Effect of preliminary thermal treatment on decomposition kinetics of austenite in low-alloyed pipe steel in intercritical temperature interval

NASA Astrophysics Data System (ADS)

Makovetskii, A. N.; Tabatchikova, T. I.; Yakovleva, I. L.; Tereshchenko, N. A.; Mirzaev, D. A.

2013-06-01

The decomposition kinetics of austenite that appears in the 13KhFA low-alloyed pipe steel upon heating the samples in an intercritical temperature interval (ICI) and exposure for 5 or 30 min has been studied by the method of high-speed dilatometry. The results of dilatometry are supplemented by the microstructure analysis. Thermokinetic diagrams of the decomposition of the γ phase are represented. The conclusion has been drawn that an increase in the duration of exposure in the intercritical interval leads to a significant increase in the stability of the γ phase.

Wear-resistance investigation of electro-screen coatings obtained using electroerosive powders of micro and nanofractions

NASA Astrophysics Data System (ADS)

Ageev, E. V.; Altukhov, A. Yu; Malneva, Yu V.; Novikov, A. N.

2018-03-01

The results of the wear resistance investigation of electro sparking coatings, applied using electrode material from electroerosive powders of hard alloy VK-8 (90%) with the addition of powder of high-speed steel of grade R6M5 (10%), are presented. Electro spark coatings were formed on samples of 30KhGSA steel using these electrodes and installation UR-121. The coefficient of friction and the wear rate of the surface of the sample and counterbody were measured on an automated friction machine “Tribometer” (CSM Instruments, Switzerland), controlled by a computer, according to the standard “ball-disk” test scheme.

HỖ TRỢ CỦA GIA ĐÌNH ĐỐI VỚI NAM TIÊM CHÍCH MA TÚY NHIỄM HIV TẠI HÀ NỘI

PubMed Central

Ngọc, Lùng Bích; Ly, An Thanh; Hòa, Trần Thị; Giang, Lê Minh

2016-01-01

Nghiên cứu định tính nhằm mô tả hỗ trợ của gia đình trong chăm sóc sức khỏe, đặc biệt trong điều trị HIV và nghiện chắt của nam tiêm chích ma túy nhiễm HIV tại Hà Nội. Kết quả phân tích cho thấy gia đình chủ yếu hỗ trợ tài chính, tinh thần và chăm sóc sức khỏe trong khi các hỗ trợ thông tin liên quan đến điều trị HIV và nghiện chất cho nam tiêm chích ma túy nhiễm HIV của gia đình còn khá hạn chế. Hỗ trợ của gia đình cho nam tiêm chích ma túy nhiễm HIV khác nhau giữa các giai đoạn sử dụng ma túy, nhiễm HIV, điều trị HIV và điều trị nghiện chất. Đáng chú ý là việc tiết lộ tình trạng nhiễm HIV đã giúp các nam tiêm chích ma túy nhận được nhiều hơn sự hỗ trợ từ gia đình. Các can thiệp nhằm nâng cao hiệu quả điều trị HIV và điều trị nghiện chất cho nam tiêm chích ma túy nhiễm HIV cần tính đến sự tham gia hỗ trợ của gia đình. PMID:28393100

Effect of electrical spot welding on load deflection rate of orthodontic wires.

PubMed

Alavi, Shiva; Abrishami, Arezoo

2015-01-01

One of the methods used for joining metals together is welding, which can be carried out using different techniques such as electric spot welding. This study evaluated the effect of electric spot welding on the load deflection rate of stainless steel and chromium-cobalt orthodontic wires. In this experimental-laboratory study, load deflection rate of 0.016 × 0.022 inch stainless steel and chromium cobalt wires were evaluated in five groups (n =18): group one: Stainless steel wires, group two: chromium-cobalt wires, group three: stainless steel wires welded to stainless steel wires, group four: Stainless steel wires welded to chromium-cobalt wires, group five: chromium-cobalt wire welded to chromium-cobalt wires. Afterward, the forces induced by the samples in 0.5 mm, 1 mm, 1.5 mm deflection were measured using a universal testing machine. Then mean force measured for each group was compared with other groups. The data were analyzed using repeated measure analysis of variance (ANOVA), one-way ANOVA, and paired t-test by the SPSS software. The significance level was set as 0.05. The Tukey test showed that there were significant differences between the load deflection rates of welded groups compared to control ones (P < 0.001). Considering the limitation of this study, the electric spot welding process performed on stainless steel and chromium-cobalt wires increased their load deflection rates.

Heterogeneous cytogenetic subgroups and outcomes in childhood acute megakaryoblastic leukemia: a retrospective international study

PubMed Central

Zhou, Yinmei; Abla, Oussama; Adachi, Souichi; Auvrignon, Anne; Beverloo, H. Berna; de Bont, Eveline; Chang, Tai-Tsung; Creutzig, Ursula; Dworzak, Michael; Elitzur, Sarah; Fynn, Alcira; Forestier, Erik; Hasle, Henrik; Liang, Der-Cherng; Lee, Vincent; Locatelli, Franco; Masetti, Riccardo; De Moerloose, Barbara; Reinhardt, Dirk; Rodriguez, Laura; Van Roy, Nadine; Shen, Shuhong; Taga, Takashi; Tomizawa, Daisuke; Yeoh, Allen E. J.; Zimmermann, Martin; Raimondi, Susana C.

2015-01-01

Comprehensive clinical studies of patients with acute megakaryoblastic leukemia (AMKL) are lacking. We performed an international retrospective study on 490 patients (age ≤18 years) with non–Down syndrome de novo AMKL diagnosed from 1989 to 2009. Patients with AMKL (median age 1.53 years) comprised 7.8% of pediatric AML. Five-year event-free (EFS) and overall survival (OS) were 43.7% ± 2.7% and 49.0% ± 2.7%, respectively. Patients diagnosed in 2000 to 2009 were treated with higher cytarabine doses and had better EFS (P = .037) and OS (P = .003) than those diagnosed in 1989 to 1999. Transplantation in first remission did not improve survival. Cytogenetic data were available for 372 (75.9%) patients: hypodiploid (n = 18, 4.8%), normal karyotype (n = 49, 13.2%), pseudodiploid (n = 119, 32.0%), 47 to 50 chromosomes (n = 142, 38.2%), and >50 chromosomes (n = 44, 11.8%). Chromosome gain occurred in 195 of 372 (52.4%) patients: +21 (n = 106, 28.5%), +19 (n = 93, 25.0%), +8 (n = 77, 20.7%). Losses occurred in 65 patients (17.5%): –7 (n = 13, 3.5%). Common structural chromosomal aberrations were t(1;22)(p13;q13) (n = 51, 13.7%) and 11q23 rearrangements (n = 38, 10.2%); t(9;11)(p22;q23) occurred in 21 patients. On the basis of frequency and prognosis, AMKL can be classified to 3 risk groups: good risk—7p abnormalities; poor risk—normal karyotypes, –7, 9p abnormalities including t(9;11)(p22;q23)/MLL-MLLT3, –13/13q-, and –15; and intermediate risk—others including t(1;22)(p13;q13)/OTT-MAL (RBM15-MKL1) and 11q23/MLL except t(9;11). Risk-based innovative therapy is needed to improve patient outcomes. PMID:26215111

Application of hard coatings to substrates at low temperatures

NASA Technical Reports Server (NTRS)

Sproul, William D.

1993-01-01

BIRL, the industrial research laboratory of Northwestern University, has conducted unique and innovative research, under sponsorship from the NASA Marshall Space Flight Center (MSFC), in the application of hard, wear resistant coatings to bearing steels using the high-rate reactive sputtering (HRRS) process that was pioneered by Dr. William Sproul, the principal investigator on this program. Prior to this program, Dr. Sproul had demonstrated that it is possible to apply hard coatings such as titanium nitride (TiN) to alloy steels at low temperatures via the HRRS process without changing the metallurgical properties of the steel. The NASA MSFC program at BIRL had the specific objectives to: apply TiN to 440C stainless steel without changing the metallurgical properties of the steel; prepare rolling contact fatigue (RCF) test samples coated with binary hard coatings of TiN, zirconium nitride (ZrN), hafnium nitride (HfN), chromium nitride (CrN), and molybdenum nitride (MoN), and metal coatings of copper (Cu) and gold (Au); and develop new alloyed hard coatings of titanium aluminum nitride (Ti(0.5)Al(0.5)N), titanium zirconium nitride (Ti(0.5)Zr(0.5)N), and titanium aluminum vanadium nitride.

Wave interactions with multiple semi-immersed Jarlan-type perforated breakwaters

NASA Astrophysics Data System (ADS)

Elbisy, Moussa S.

2017-06-01

This study examines wave interactions with multiple semi-immersed Jarlan-type perforated breakwaters. A numerical model based on linear wave theory and an eigenfunction expansion method has been developed to study the hydrodynamic characteristics of breakwaters. The numerical results show a good agreement with previous analytical results and experimental data for limiting cases of double partially immersed impermeable walls and double and triple Jarlan-type breakwaters. The wave transmission coefficient C T; reflection coefficient C R, and energy dissipation coefficient C E coefficients and the horizontal wave force exerted on the front and rear walls are examined. The results show that C R reaches the maximum value when B/L = 0.46 n while it is smallest when B/L=0.46 n+0.24 ( n=0, 1, 2,...). An economical triple semi-immersed Jarlan-type perforated breakwater can be designed with B/L = 0.25 and C R and C T ranging from 0.25 to 0.32 by choosing a relative draft d/h of 0.35 and a permeability parameter of the perforated front walls being 0.5 for an incident wave number kh nearly equal to 2.0. The triple semi-immersed Jarlan-type perforated breakwaters with significantly reduced C R, will enhance the structure's wave absorption ability, and lead to smaller wave forces compared with the double one. The proposed model may be used to predict the response of a structure in the preliminary design stage for practical engineering.

Martensitic transformations, structure, and strengthness of processed high-nitrogen and high-carbon ferrous alloys

NASA Astrophysics Data System (ADS)

Kaputkina, L. M.; Prokoshkina, V. G.

2003-10-01

Structures and properties of metastable austenitic alloys Fe-18Cr-16Ni-I2Mn-(0.17 to 0. 50)N, Fe-18Cr-12Mn-(0.48 to 1.12)N, Fe-18Cr-(0.1 to 1.18)N, and Fe-(12 to 20)Ni-(0.6 to 1.3)C, Fe-(6 to 8)Mn-(0.6 to 1.0)C, Fe-(5 to 6)Cr-(4 to 5)Mn-(0.6 to 0.8)C, Fe-6Cr-(1.0 to 1.3)C resulting from martensitic transformations under cooling and cold deformation (CD), as well as following tempering processes, were studied by magnetometry, X-ray and electron microscopy analyses, hardness measurements and mechanical properties tests. Martensite with a b.c.t. lattice was formed in all alloys with M_s{>}-196^circC during cooling. Under CD transformations of γ{to}α, γ{to}\\varepsilon{to}α, or γ{to}\\varepsilon types were realized depending on the alloy composition. Carbon increased but nitrogen decreased stacking fault energy. Thus carbon assists α-martensite formation but nitrogen promotese. As CD level and/or concentration of carbon and nitrogen increase residual stresses resulting from the CD also increase. The martensitic transformation during CD can decrease the residual stresses. Kinetic of tempering of b.c.t. thermal martensite differs from those of CD-induced martensite. In the second case, deformation aging, texture, and residual stresses are more visible. The maximal strengthening under CD takes place in (Mn+N)-steels. (Cr+N) and (Cr+Mn+N)-steels are high-strength, non-magnetic and corrosion resistant and are easily hardened by a low level of plastic deformation.

27 CFR 9.187 - Covelo.

Code of Federal Regulations, 2014 CFR

2014-04-01

...), proceed west 0.3 miles on Highway 162 to BM 2006 in section 36, T22N, R13W; then (2) Proceed straight west-northwest 1.5 miles to the 2,537-foot elevation point in the northwest quadrant of section 26, T22N, R13W, Dos Rios map; then (3) Proceed straight northwest 1.6 miles to the 2,488-foot peak in the northwest...

27 CFR 9.187 - Covelo.

Code of Federal Regulations, 2012 CFR

2012-04-01

...), proceed west 0.3 miles on Highway 162 to BM 2006 in section 36, T22N, R13W; then (2) Proceed straight west-northwest 1.5 miles to the 2,537-foot elevation point in the northwest quadrant of section 26, T22N, R13W, Dos Rios map; then (3) Proceed straight northwest 1.6 miles to the 2,488-foot peak in the northwest...

27 CFR 9.187 - Covelo.

Code of Federal Regulations, 2013 CFR

2013-04-01

...), proceed west 0.3 miles on Highway 162 to BM 2006 in section 36, T22N, R13W; then (2) Proceed straight west-northwest 1.5 miles to the 2,537-foot elevation point in the northwest quadrant of section 26, T22N, R13W, Dos Rios map; then (3) Proceed straight northwest 1.6 miles to the 2,488-foot peak in the northwest...

All Prime Contract Awards by State or Country, Place, and Contractor. Part 22 (Aua Amer-Honduras)

DTIC Science & Technology

1990-01-01

5 01 񓡞i 0 La 4. U.444.4 4c 4c 41* UWl dc 4c...4C C. 0 d IL ~a.4 MW 1-1 U be 0 a 00003 0 mU 0 * a I 10.4 CD LL 00 Go G00 40 0000 1-1 qW In 0 40 t&. - 5 -4 -i..t- maoooonon 04.)m -im’ 000o >.a 0 . CV...00 t 2 Q0000000 OaN xa i004 aNO4 5 -1- J-JIJ-J 00 0 00f 0.4c 000000 0 1010CL a41 d-# 1 300000 22 1 00 wa 00000000 02 -9 a 3 4") a~ A -4-4 .4 -4-4 a 0

Resolute Apt, Northwest Territories, Canada. Revised Uniform Summary of Surface Weather Observations (RUSSWO). Parts A-F.

DTIC Science & Technology

1972-01-17

ITS ASHEVILLE, N. C. II POI L, TD ’ Reiew and-Approval Statement This report is approved for public release. There is no objection to unlimited...14000 -,46 0 t* ski :ph 0 51194 TTj i-ri -T-. _T7. 40( -~677. - Td -. 7.4 12000 40’ aiNb6 5(2,7 03*1 67.0 67*9 7gT) 7Z* 9 7Z*9 70,0 77., 774 70uZ i 1...DEPRESSION (F) TOTAL TOTAL(F I o 1 2 3 4 5 - ..7 - . - 27-..8. .93...B W8- BubWe B.b TD ..ew . (F’ 0 . 2 3-4 ’ 5-6 7.8 9-10 1.12 13-1415-16 17- 819.20 21-22 22

Investigation of the interfacial reactions between steel and aluminum coatings for hybrid casting

NASA Astrophysics Data System (ADS)

Bobzin, K.; Öte, M.; Wiesner, S.; Gerdt, L.

2018-06-01

Coating of AA7075 was applied by means of cold gas spraying on steel substrates of 22MnB5 and DC04 as an interlayer for high pressure die casting of aluminum/steel hybrid components. The morphology and growth kinetics of intermetallic compounds formed at the interface between coating and steel has been investigated. Furthermore, the effect of alloying elements on the formation of the intermetallic phases was analyzed. The coated samples were heat treated by means of induction heating at the temperature T = 550 °C with different dwell times in the range of 10 s < t < 5 min. The reaction layer growth was examined by means of scanning electron microscope (SEM) with energy dispersive spectroscopy (EDS). Additionally, the intermetallic compounds were characterized by means of nanoindentation. Intermetallic compounds of AlFe phases occurred as the major constituent in the reaction zone for different combinations of coating and substrates.

Plasma lipidomics reveals potential prognostic signatures within a cohort of cystic fibrosis patients

PubMed Central

Ollero, Mario; Astarita, Giuseppe; Guerrera, Ida Chiara; Sermet-Gaudelus, Isabelle; Trudel, Stéphanie; Piomelli, Daniele; Edelman, Aleksander

2011-01-01

Cystic fibrosis (CF) is associated with abnormal lipid metabolism. We have recently shown variations in plasma levels of several phosphatidylcholine (PC) and lysophopshatidylcholine (LPC) species related to disease severity in CF patients. Here our goal was to search for blood plasma lipid signatures characteristic of CF patients bearing the same mutation (F508del) and different phenotypes, and to study their correlation with forced expiratory volume in 1 s (FEV1) and Pseudomonas aeruginosa chronic infection, evaluated at the time of testing (t = 0) and three years later (t = 3). Samples from 44 F508del homozygotes were subjected to a lipidomic approach based on LC-ESI-MS. Twelve free fatty acids were positively correlated with FEV1 at t = 0 (n = 29). Four of them (C20:3n-9, C20:5n-3, C22:5n-3, and C22:6n-3) were also positively correlated with FEV1 three years later, along with PC(32:2) and PC(36:4) (n = 31). Oleoylethanolamide (OEA) was negatively correlated with FEV1 progression (n = 17). Chronically infected patients at t = 0 showed lower PC(32:2), PC(38:5), and C18:3n-3 and higher cholesterol, cholesterol esters, and triacylglycerols (TAG). Chronically infected patients at t = 3 showed significantly lower levels of LPC(18:0). These results suggest a potential prognostic value for some lipid signatures in, to our knowledge, the first longitudinal study aimed at identifying lipid biomarkers for CF. PMID:21335323

Effect of heat-treatment conditions on the structure and physicomechanical and chemical properties of a Ni-Cr-Cu-Ti maraging steel

NASA Astrophysics Data System (ADS)

Bannykh, O. A.; Berezovskaya, V. V.

2007-06-01

The effects of quenching (from 950°C or from 950 and 850°C) and the aging conditions on the structure, properties, and delayed fracture (DF) of 03Kh11N10M2DT maraging steel has been studied by dilatometry, X-ray diffraction, and fracture tests. The DF-crack growth rate is maximal after aging at 400°C irrespective of the quenching conditions, and the corrosion rate is maximal after aging at 350 400°C in the case of single quenching and at 350°C after double quenching. The kinetics and mechanism of the early stages of the decomposition of a supersaturated α solid solution are investigated by electrical-resistance measurements and transmission electron microscopy. In the state after single quenching, aging occurs in two stages at all isothermal heat treatments; in the state after double quenching, aging occurs in one stage at a time exponent n = 0.2 in the Johnson-Mehl equation. Upon aging at 400°C, the intermediate ordered Fe3(Ni,Ti) phase with a complex cubic lattice precipitates, and the intermetallic compound Ni3Ti precipitates upon subsequent aging. Moreover, copper-rich ɛ-phase precipitates form only in the case of single quenching. The substantial increase in the crack growth rate during DF with n < 0.2 is likely to be caused by the formation of Guinier-Preston zones enriched in nickel and titanium.

Preparation of Stable Photopatternable Polymeric Materials for Non- linear Optics

DTIC Science & Technology

1993-05-01

Scheme 3 OC 2)2-, .~(CH 2)2O N"I ~ NI H IH NCO dibutyltin-0 6a + OCN dilaurateD, DMF 0 0a r - 0 0 -N)K 0(CH22,,(H)OAN I Id H IHo=s= o NCO0n 6b + OC...Angerer, V. Desobry, K. Dietliker, R . Husler ; Proc. 16th Inter. Cont. in Ort nic Coatings Science and Technology, (July 9-13, 1990) Athens, Greece, 423. 7 ...AD-A265 359 O AGMB N.’ 0704-0Orpq 1. AGEN My1,993 3. REPORT TYPE AND OATES COVERED May12 T99 Technical Re port # IQ. 4. TITLE AND SUBTITLE 5. FUNDING

Hydrothermal growth of potassium titanyl arsenate (KTA) in large autoclaves

NASA Astrophysics Data System (ADS)

Belt, Roger F.; Ings, John B.

1993-03-01

Solubility and phase relations were investigated for selected K/As ratios in KH2AsO4-KOH solutions at 600°C and 2040 atm. All initial data were obtained with 5 mm diameter x 50 mm long platinum capsules in Tem-Pres type autoclaves. The most favorable results were repeated in Morey type autoclaves of 2.2 cm diameter. The P-V-T data were generated and extrapolated for use in gold liners and René 41 autoclaves with a pressure balancing method. Transfer to the 3.8 cm diameter x 46 cm long autoclaves with gold liners was achieved. Both nutrient and larger seed crystals were grown from a K2WO4-Li2WO4 flux. The internal and external degrees of fill were adjusted to obtain a balance of pressure at 1700 atm and 590°C. Initial growth runs were made for 1-2 weeks under a gradient of 30°C with a 4 molar KH2AsO4 mineralizer. Natural facet seeds were employed first while later runs utilized (011) cut and polished seeds.

Summary of Meteorological Observations, Surface (SMOS) for Keflavik, Iceland

DTIC Science & Technology

1989-04-01

is not considered obstruction to vision for purposes of this summary; therefore, the percentage total of obstructions to vis need not reflect the total...1 .J . I0 . . 1 0 .0 .c IC 10 .5 CLP .’ .C .0 . : . .0 C0 1.2 .0 AL 3I.4 331. 3 2%. 1 ’* A$. p~t r~ r Iro C0 I03’. 2 T VI AL N. (3 0~A 10 t 42 p f W...55w ’LI. • b VI "w" Jut NOUN :0 n0 Lk 1 ):51 )il /4Il6 : J ): r , 7(2. 20.6 72.1 20.7 70.7 ,’ 7 1. 21.6 7.1 7 II-? 71.1 .S 22.( 22.6 72.7 27.7 72

Parasitic Disease in the U.S. Navy

DTIC Science & Technology

1989-07-21

Protozoal (007)* 80 1.9 (1.5, 2.4) Amebiasis (006) 78 1.9 (1.5,2.3) Malaria (084) 52 1.2 (0.9, 1.6) Other infestation (134)t 47 1.1 (0.8, 1.5) Toxoplasmosis ...N-30) (-1127) (N-78) (N-112) (N-106) (N-52) Toxoplasmosis 65.0 0.0 0.0 0.0 0.0 0.0 Other intestinal helmlnthiasis 0.0 33.0 0.0 0.0 0.0 0.0 Amebiasis...Other unspecified helminth 2 1 6 5.0 Toxoplasmosis 30 0 10 16.0 Trichomoniasis A 82 22* 9.0 Pediculosis 17 0 100 9.2 Acariasis 106 6 95 14.0 Other

Durability of bends in high-temperature steam lines under the conditions of long-term operation

NASA Astrophysics Data System (ADS)

Katanakha, N. A.; Semenov, A. S.; Getsov, L. B.

2015-04-01

The article presents the results of stress-strain state computations and durability of bent and steeply curved branches of high-temperature steam lines carried out on the basis of the finite element method using the modified Soderberg formula for describing unsteady creep processes with taking the accumulation of damage into account. The computations were carried out for bends made of steel grades that are most widely used for manufacturing steam lines (12Kh1MF, 15Kh1M1F, and 10Kh9MFB) and operating at different levels of inner pressure and temperature. The solutions obtained using the developed creep model are compared with those obtained using the models widely used in practice.

Elevated Temperature Corrosion Studies of AlCrN and TiAlN Coatings by PAPVD on T91 Boiler Steel

NASA Astrophysics Data System (ADS)

Goyal, Lucky; Chawla, Vikas; Hundal, Jasbir Singh

2017-11-01

The present investigation discusses the hot corrosion behavior of AlCrN and TiAlN nano-coatings on T91 boiler steel by PAPVD process subjected to molten salt of Na2SO4-60%V2O5 at 900 °C for 50 cycles. Surface and cross-sectional studies were performed by AFM, SEM/EDS and XRD techniques to understand the corrosion kinetics and mechanism. T91 bare boiler steel as well as TiAlN-coated specimen has shown higher internal oxidation as well as weight gain. The better corrosion resistance of AlCrN-coated specimen has been observed by virtue of higher availability of Cr and Al in the oxide scale as well as adherent and dense coating. The betterment of AlCrN coating can be attributed to low internal oxidation as well as movement of Cr and Al toward oxide scale to form protective corrosion barriers.

Creep and microstructural processes in a low-alloy 2.25%Cr1.6%W steel (ASTM Grade 23)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kucharova, K.; Sklenicka, V., E-mail: sklen@ipm.cz; CEITEC — IPM, Institute of Physics of Materials, Academy of Sciences of the Czech Republic, CZ-616 62 Brno

2015-11-15

A low-alloy 2.25%Cr1%Mo steel (ASTM Grade 22) has been greatly improved by the substitution of almost all of the 1%Mo by 1.6%W. The improved material has been standardized as P/T23 steel (Fe–2.25Cr–1.6W–0.25V–0.05Nb–0.07C). The present investigation was conducted on T23 steel in an effort to obtain a more complete description and understanding of the role of the microstructural evolution and deformation processes in high-temperature creep. Constant load tensile creep tests were carried out in an argon atmosphere in the temperature range 500–650 °C at stresses ranging from 50 to 400 MPa. It was found that the diffusion in the matrix latticemore » is the creep-rate controlling process. The results of an extensive transmission electron microscopy (TEM) analysis programme to investigate microstructure evolution as a function of temperature are described and compared with the thermodynamic calculations using the software package Thermo-Calc. The significant creep-strength drop of T23 steel after long-term creep exposures can be explained by the decrease in dislocation hardening, precipitation hardening and solid solution hardening due to the instability of the microstructure at high temperature. - Highlights: • The constant load creep tests of T23 steel were carried out at 500–650 °C. • The stress exponents of the creep rate correspond to power law (dislocation) creep. • Diffusion in the matrix lattice is the creep-rate controlling process. • The microstructure instability is the main creep degradation process in T23 steel.« less

Effects of High Power Lasers, Number 5, September 1974 - February 1975

DTIC Science & Technology

1975-05-01

EOM J AiO FG1V FiKhOM F-KhMM FMiM FTP FTT FZh GiA GiK IAN Arm D\\.N Az SOURCE AB13Ri:viATIONS Avtomatika i tclcmekhanika Acta physica ... polonica Akadcniya nauk Armyanskoy SSR. Doklady Akadcrniya nauk Azerbaydzhanskoy SSR. Doklady Akadcrniya nauk Belorusskoy SSR. Doklady Ak

Precipitation and Phase Transformations in 2101 Lean Duplex Stainless Steel During Isothermal Aging

NASA Astrophysics Data System (ADS)

Maetz, Jean-Yves; Cazottes, Sophie; Verdu, Catherine; Kleber, Xavier

2016-01-01

The effect of isothermal aging at 963 K (690 °C) on the microstructure of a 2101 lean duplex stainless steel, with the composition Fe-21.5Cr-5Mn-1.6Ni-0.22N-0.3Mo, was investigated using a multi-technique and multi-scale approach. The kinetics of phase transformation and precipitation was followed from a few minutes to thousands of hours using thermoelectric power measurements; based on these results, certain aging states were selected for electron microscopy characterization. Scanning electron microscopy, electron back-scattered diffraction, and transmission electron microscopy were used to quantitatively describe the microstructural evolution through crystallographic analysis, chemical analysis, and volume fraction measurements from the macroscopic scale down to the nanometric scale. During aging, the precipitation of M23C6 carbides, Cr2N nitrides, and σ phase as well as the transformation of ferrite into austenite and austenite into martensite was observed. These complex microstructural changes are controlled by Cr volume diffusion. The precipitation and phase transformation mechanisms are described.

Time-Reversal Based Range Extension Technique for Ultra-Wideband (UWB) Sensors and Applications in Tactical Communications and Networking

DTIC Science & Technology

2009-01-16

i0ii ••• xNx ] T (5.11) Construct channel matrix H(NX+I)X(NP+I)’ where (•)<, denotes the entry in the i-th row and j-th column of the matrix or vector...should be minimized. The entries in x outside integration window constitute x/ as, X; = [ar0 • • E/Vjo-l xN,n+N,+l • • • xNx ] T (5.22) and the

Creep and Oxidation Behavior of Modified CF8C-Plus with W, Cu, Ni, and Cr

NASA Astrophysics Data System (ADS)

Unocic, Kinga A.; Dryepondt, Sebastien; Yamamoto, Yukinori; Maziasz, Philip J.

2016-04-01

The microstructures of modified CF8C-Plus (Fe-19Cr-12Ni-0.4W-3.8Mn-0.2Mo-0.6Nb-0.5Si-0.9C) with W and Cu (CF8CPWCu) and CF8CPWCu enhanced with 21Cr + 15Ni or 22Cr + 17.5Ni were characterized in the as-cast condition and after creep testing. When imaged at lower magnifications, the as-cast microstructure was similar among all three alloys as they all contained a Nb-rich interdendritic phase and Mn-based inclusions. Transmission electron microscopy (TEM) analysis showed the presence of nanoscale Cu-rich nanoprecipitates distributed uniformly throughout the matrix of CF8CPWCu, whereas in CF8CPWCu22/17, Cu precipitates were found primarily at the grain boundaries. The presence of these nanoscale Cu-rich particles, in addition to W-rich Cr23C6, nanoscale Nb carbides, and Z-phase (Nb2Cr2N2), improved the creep strength of the CF8CPWCu steel. Modification of CF8CPWCu with Cr and Ni contents slightly decreased the creep strength but significantly improved the oxidation behavior at 1073 K (800 °C). In particular, the addition of 22Cr and 17.5Ni strongly enhanced the oxidation resistance of the stainless steel resulting in a 100 degrees or greater temperature improvement, and this composition provided the best balance between improving both mechanical properties and oxidation resistance.

Creep and oxidation behavior of modified CF8C-plus with W, Cu, Ni, and Cr

DOE Office of Scientific and Technical Information (OSTI.GOV)

Unocic, Kinga A.; Dryepondt, Sebastien N.; Yamamoto, Yukinori

Here, the microstructures of modified CF8C-Plus (Fe-19Cr-12Ni-0.4W-3.8Mn-0.2Mo-0.6Nb-0.5Si-0.9C) with W and Cu (CF8CPWCu) and CF8CPWCu enhanced with 21Cr + 15Ni or 22Cr + 17.5Ni were characterized in the as-cast condition and after creep testing. When imaged at lower magnifications, the as-cast microstructure was similar among all three alloys as they all contained a Nb-rich interdendritic phase and Mn-based inclusions. Transmission electron microscopy (TEM) analysis showed the presence of nanoscale Cu-rich nanoprecipitates distributed uniformly throughout the matrix of CF8CPWCu, whereas in CF8CPWCu22/17, Cu precipitates were found primarily at the grain boundaries. The presence of these nanoscale Cu-rich particles, in addition to W-richmore » Cr 23C 6, nanoscale Nb carbides, and Z-phase (Nb 2Cr 2N 2), improved the creep strength of the CF8CPWCu steel. Modification of CF8CPWCu with Cr and Ni contents slightly decreased the creep strength but significantly improved the oxidation behavior at 1073 K (800 °C). In particular, the addition of 22Cr and 17.5Ni strongly enhanced the oxidation resistance of the stainless steel resulting in a 100 degrees or greater temperature improvement, and this composition provided the best balance between improving both mechanical properties and oxidation resistance.« less

Creep and oxidation behavior of modified CF8C-plus with W, Cu, Ni, and Cr

DOE PAGES

Unocic, Kinga A.; Dryepondt, Sebastien N.; Yamamoto, Yukinori; ...

2016-02-01

Here, the microstructures of modified CF8C-Plus (Fe-19Cr-12Ni-0.4W-3.8Mn-0.2Mo-0.6Nb-0.5Si-0.9C) with W and Cu (CF8CPWCu) and CF8CPWCu enhanced with 21Cr + 15Ni or 22Cr + 17.5Ni were characterized in the as-cast condition and after creep testing. When imaged at lower magnifications, the as-cast microstructure was similar among all three alloys as they all contained a Nb-rich interdendritic phase and Mn-based inclusions. Transmission electron microscopy (TEM) analysis showed the presence of nanoscale Cu-rich nanoprecipitates distributed uniformly throughout the matrix of CF8CPWCu, whereas in CF8CPWCu22/17, Cu precipitates were found primarily at the grain boundaries. The presence of these nanoscale Cu-rich particles, in addition to W-richmore » Cr 23C 6, nanoscale Nb carbides, and Z-phase (Nb 2Cr 2N 2), improved the creep strength of the CF8CPWCu steel. Modification of CF8CPWCu with Cr and Ni contents slightly decreased the creep strength but significantly improved the oxidation behavior at 1073 K (800 °C). In particular, the addition of 22Cr and 17.5Ni strongly enhanced the oxidation resistance of the stainless steel resulting in a 100 degrees or greater temperature improvement, and this composition provided the best balance between improving both mechanical properties and oxidation resistance.« less

Properties of super stainless steels for orthodontic applications.

PubMed

Oh, Keun-Taek; Kim, Young-Sik; Park, Yong-Soo; Kim, Kyoung-Nam

2004-05-15

Orthodontic stainless-steel appliances are considered to be corrosion resistant, but localized corrosion can occur in the oral cavity. This study was undertaken to evaluate the properties of super stainless steels in orthodontic applications. Accordingly, the metallurgical properties, mechanical properties, corrosion resistance, amount of the released nickel, cytotoxicity, and characteristics of the passive film were investigated. Corrosion resistances of the specimens were high and in the following order: super austenitic stainless steel (SR-50A) > super ferritic stainless steel (SFSS) = super duplex stainless steel (SR-6DX) > 316L SS > super martensitic stainless steel (SR-3Mo) in artificial saliva, 37 degrees C. At 500 mV (SCE), current densities of SR-50A, SFSS, SR-6DX, 316L SS, and SR-3Mo were 5.96 microA/cm(2), 20.3 microA/cm(2), 31.9 microA/cm(2), 805 microA/cm(2), and 5.36 mA/cm(2), respectively. Open circuit potentials of SR-50A, 316L SS, SR-6DX, SR-3Mo, and SFSS were - 0.2, - 0.22, - 0.24, - 0.43, and - 0.46 V (SCE), respectively. SR-50A, SFSS, and SR-6DX released below 3 ng/ml nickel for 8 weeks, and increased a little with immersion time, and 316L SS released about 3.5 ng/ml nickel, but SR-3Mo released a large amount of nickel, which increased with immersion time. The study demonstrated that SR-50A, SR-6DX, and SFSS have high corrosion resistance and mild or no cytotoxicity, due to the passive film enhanced by synergistic effect of Mo + N or by high addition effect of Cr + W. All super stainless steels showed very low cytotoxicity regardless of their nickel contents, although SR-3Mo was found to be relatively cytotoxic. From these studies, these steels are considered suitable for orthodontic applications. Copyright 2004 Wiley Periodicals, Inc.

Transportation Lines on the Great Lakes System; Transportation Series 3; 1980.

DTIC Science & Technology

1982-05-01

I 94 24 29 O 22. SPAR NONE CALCITE, 1952 ELECTRIC, STEEL MICH. (221 LITTON GREAT LA ES CORP, MJV PRESQUE ISLE TOWBOAT; STEEL 107 141 IS S4 5 2 21...1464 - -6 LIGHT NONE ERIE , PA, 1973PRESQUE ISLE BARGE, STEEL 22251 94 974 104 104 . 12 - 5720 7 6, LIGHT SE4F-UNLOADIN- DO 1973 ELEC., 250’ BOOM- 10,000...MOTOR, DIESEL. 1 37 41 I t 230 -, PAST NONE LGONAC. 1948 STEEL NIC. (23) PARKER BOAT 4INI ERIE ISLE MOTOR, DIESEL, 4 6 6 24 2 9 330 2 16014o LIGHT

Behavior of ferritic/martensitic steels after n-irradiation at 200 and 300 °C

NASA Astrophysics Data System (ADS)

Matijasevic, M.; Lucon, E.; Almazouzi, A.

2008-06-01

High chromium ferritic/martensitic (F/M) steels are considered as the most promising structural materials for accelerator driven systems (ADS). One drawback that needs to be quantified is the significant hardening and embrittlement caused by neutron irradiation at low temperatures with production of spallation elements. In this paper irradiation effects on the mechanical properties of F/M steels have been studied and comparisons are provided between two ferritic/martensitic steels, namely T91 and EUROFER97. Both materials have been irradiated in the BR2 reactor of SCK-CEN/Mol at 300 °C up to doses ranging from 0.06 to 1.5 dpa. Tensile tests results obtained between -160 °C and 300 °C clearly show irradiation hardening (increase of yield and ultimate tensile strengths), as well as reduction of uniform and total elongation. Irradiation effects for EUROFER97 starting from 0.6 dpa are more pronounced compared to T91, showing a significant decrease in work hardening. The results are compared to our latest data that were obtained within a previous program (SPIRE), where T91 had also been irradiated in BR2 at 200 °C (up to 2.6 dpa), and tested between -170 °C and 300 °C. Irradiation effects at lower irradiation temperatures are more significant.

Observations of Kelvin-Helmholtz instability at a cloud base with the middle and upper atmosphere (MU) and weather radars

NASA Astrophysics Data System (ADS)

Luce, Hubert; Mega, Tomoaki; Yamamoto, Masayuki K.; Yamamoto, Mamoru; Hashiguchi, Hiroyuki; Fukao, Shoichiro; Nishi, Noriyuki; Tajiri, Takuya; Nakazato, Masahisa

2010-10-01

Using the very high frequency (46.5 MHz) middle and upper atmosphere radar (MUR), Ka band (35 GHz) and X band (9.8 GHz) weather radars, a Kelvin-Helmholtz (KH) instability occurring at a cloud base and its impact on modulating cloud bottom altitudes are described by a case study on 8 October 2008 at the Shigaraki MU Observatory, Japan (34.85°N, 136.10°E). KH braids were monitored by the MUR along the slope of a cloud base gradually rising with time around an altitude of ˜5.0 km. The KH braids had a horizontal wavelength of about 3.6 km and maximum crest-to-trough amplitude of about 1.6 km. Nearly monochromatic and out of phase vertical air motion oscillations exceeding ±3 m s-1 with a period of ˜3 min 20 s were measured by the MUR above and below the cloud base. The axes of the billows were at right angles of the wind and wind shear both oriented east-north-east at their altitude. The isotropy of the radar echoes and the large variance of Doppler velocity in the KH billows (including the braids) indicate the presence of strong turbulence at the Bragg (˜3.2 m) scale. After the passage of the cloud system, the KH waves rapidly damped and the vertical scale of the KH braids progressively decreased down to about 100 m before their disappearance. The radar observations suggest that the interface between clear air and cloud was conducive to the presence of the dynamical shear instability by reducing static stability (and then the Richardson number) near the cloud base. Downward cloudy protuberances detected by the Ka band radar had vertical and horizontal scales of about 0.6-1.1 and 3.2 km, respectively, and were clearly associated with the downward air motions. Observed oscillations of the reflectivity-weighted Doppler velocity measured by the X band radar indicate that falling ice particles underwent the vertical wind motions generated by the KH instability to form the protuberances. The protuberances at the cloud base might be either KH billow clouds or perhaps some sort of mamma. Reflectivity-weighted particle fall velocity computed from Doppler velocities measured by the X band radar and the MUR showed an average value of 1.3 ms-1 within the cloud and in the protuberance environment.

Fort Wayne, Muni, Indiana. Revised Uniform Summary of Surface Weather Observations (RUSSWO). Parts A-F.

DTIC Science & Technology

1987-10-09

1-4 7 4R-S5 6.E S6 FETAL MEAN I DF I.REELS I I hIND N I .~ .? 1 9 .93.7 A.1 PcE 3 .1 .3 .213 9 .8 NI . . .3 . 1.6 P .9 ENE 1 ~ .2 1.3 .3 1.3 Ic. 7 L 5...11.2 3. 7 .9 22.R 13. 1 N 1 .1 2.6 .4 . 3 4 6. 7 9.6 NW I .5 2.2 1.1 .2 4.9 9.8 t: , 1.7 1.7 1.2 .1 6.5 p .6...1.2 . ,2 .0 12,7 II*- S .1 j1.9 6.1 0.2 .0 2.5 .1 21.A 1Z.8 bUW • . 1.2 2.1 I.p .5 .1 5. p 10.2 NW . 1.3 n .0 1.6 .3 .0 .2 9.7 NA .2 2.2 1, 3.3 ,2 .2 4,4

Structure and properties of corrosion and wear resistant Cr-Mn-N steels

NASA Astrophysics Data System (ADS)

Lenel, U. R.; Knott, B. R.

1987-06-01

Steels containing about 12 pct Cr, 10 pct Mn, and 0.2 pct N have been shown to have an unstable austenitic microstructure and have good ductility, extreme work hardening, high fracture strength, excellent toughness, good wear resistance, and moderate corrosion resistance. A series of alloys containing 9.5 to 12.8 pct Cr, 5.0 to 10.4 pct Mn, 0.16 to 0.32 pct N, 0.05 pct C, and residual elements typical of stainless steels was investigated by microstructural examination and mechanical, abrasion, and corrosion testing. Microstructures ranged from martensite to unstable austenite. The unstable austenitic steels transformed to α martensite on deformation and displayed very high work hardening, exceeding that of Hadfield’s manganese steels. Fracture strengths similar to high carbon martensitic stainless steels were obtained while ductility and toughness values were high, similar to austenitic stainless steels. Resistance to abrasive wear exceeded that of commercial abrasion resistant steels and other stainless steels. Corrosion resistance was similar to that of other 12 pct Cr steels. Properties were not much affected by minor compositional variations or rolled-in nitrogen porosity. In 12 pct Cr-10 pct Mn alloys, ingot porosity was avoided when nitrogen levels were below 0.19 pet, and austenitic microstructures were obtained when nitrogen levels exceeded 0.14 pct.

Installation Restoration Program. Volume 3. 152nd Tactical Reconnaissance Group, Nevada Air National Guard, Reno Cannon International Airport, Reno, Nevada

DTIC Science & Technology

1994-04-01

N F-67 PROJECTt REINO AZR NATIONAL GUARD DATE:03/25/94 ANALYSIS: BNA - CONTANINATZON REPORT REVIEWER: DENNIS MART27...10SS 0.569 0.7021 -23.4 T 12/14/92 2259 CRIoemmA 3 loSS 0.027 1.011 -22.2 T 12/14/92 2259 DIO 1055 l 0.703 .0.11 -22.5 T 12/14/92 2259 NTUL= CULORIDS...seetma. rule VOL DIo -U-T...z..-- 1064 1055 Perocnt D in the Coatcal ezood limits. wa 1064 10ss The ouaes.. does not met 52/102 no contemin. rule NIT

Biomarkers of exposure to stainless steel tungsten inert gas welding fumes and the effect of exposure on exhaled breath condensate.

PubMed

Riccelli, Maria Grazia; Goldoni, Matteo; Andreoli, Roberta; Mozzoni, Paola; Pinelli, Silvana; Alinovi, Rossella; Selis, Luisella; Mutti, Antonio; Corradi, Massimo

2018-08-01

The respiratory tract is the main target organ of the inhaled hexavalent chromium (Cr-VI) and nickel (Ni) contained in stainless steel (SS) welding fumes (WFs). The aim of this study was to investigate the Cr and Ni content of the exhaled breath condensate (EBC) of SS tungsten inert gas (TIG) welders, and relate their concentrations with oxidative stress and inflammatory biomarkers. EBC and urine from 100 SS TIG welders were collected pre-(T 0 ) and post-shift (T 1 ) on a Friday, and pre-shift (T 2 ) on the following Monday morning. Both EBC and urinary Cr concentrations were higher at T 1 (0.08 μg/L and 0.71 μg/g creatinine) and T 0 (0.06 μg/L and 0.74 μg/g creatinine) than at T 2 (below the limit of detection [LOD] and 0.59 μg/g creatinine), and EBC Ni concentrations generally remained

A third generation vaccine for human visceral leishmaniasis and post kala azar dermal leishmaniasis: First-in-human trial of ChAd63-KH

PubMed Central

Osman, Mohamed; Mistry, Anoop; Keding, Ada; Cook, Elizabeth; Wiggins, Rebecca; Di Marco, Stefania; Colloca, Stefano; Siani, Loredana; Smith, Deborah F.; Aebischer, Toni; Lacey, Charles J.

2017-01-01

Background Visceral leishmaniasis (VL or kala azar) is the most serious form of human leishmaniasis, responsible for over 20,000 deaths annually, and post kala azar dermal leishmaniasis (PKDL) is a stigmatizing skin condition that often occurs in patients after successful treatment for VL. Lack of effective or appropriately targeted cell mediated immunity, including CD8+ T cell responses, underlies the progression of VL and progression to PKDL, and can limit the therapeutic efficacy of anti-leishmanial drugs. Hence, in addition to the need for prophylactic vaccines against leishmaniasis, the development of therapeutic vaccines for use alone or in combined immuno-chemotherapy has been identified as an unmet clinical need. Here, we report the first clinical trial of a third-generation leishmaniasis vaccine, developed intentionally to induce Leishmania-specific CD8+ T cells. Methods We conducted a first-in-human dose escalation Phase I trial in 20 healthy volunteers to assess the safety, tolerability and immunogenicity of a prime-only adenoviral vaccine for human VL and PKDL. ChAd63-KH is a replication defective simian adenovirus expressing a novel synthetic gene (KH) encoding two Leishmania proteins KMP-11 and HASPB. Uniquely, the latter was engineered to reflect repeat domain polymorphisms and arrangements identified from clinical isolates. We monitored innate immune responses by whole blood RNA-Seq and antigen specific CD8+ T cell responses by IFNγ ELISPOT and intracellular flow cytometry. Findings ChAd63-KH was safe at intramuscular doses of 1x1010 and 7.5x1010 vp. Whole blood transcriptomic profiling indicated that ChAd63-KH induced innate immune responses characterized by an interferon signature and the presence of activated dendritic cells. Broad and quantitatively robust CD8+ T cell responses were induced by vaccination in 100% (20/20) of vaccinated subjects. Conclusion The results of this study support the further development of ChAd63-KH as a novel third generation vaccine for VL and PKDL. Trial registration This clinical trial (LEISH1) was registered at EudraCT (2012-005596-14) and ISRCTN (07766359). PMID:28498840

A third generation vaccine for human visceral leishmaniasis and post kala azar dermal leishmaniasis: First-in-human trial of ChAd63-KH.

PubMed

Osman, Mohamed; Mistry, Anoop; Keding, Ada; Gabe, Rhian; Cook, Elizabeth; Forrester, Sarah; Wiggins, Rebecca; Di Marco, Stefania; Colloca, Stefano; Siani, Loredana; Cortese, Riccardo; Smith, Deborah F; Aebischer, Toni; Kaye, Paul M; Lacey, Charles J

2017-05-01

Visceral leishmaniasis (VL or kala azar) is the most serious form of human leishmaniasis, responsible for over 20,000 deaths annually, and post kala azar dermal leishmaniasis (PKDL) is a stigmatizing skin condition that often occurs in patients after successful treatment for VL. Lack of effective or appropriately targeted cell mediated immunity, including CD8+ T cell responses, underlies the progression of VL and progression to PKDL, and can limit the therapeutic efficacy of anti-leishmanial drugs. Hence, in addition to the need for prophylactic vaccines against leishmaniasis, the development of therapeutic vaccines for use alone or in combined immuno-chemotherapy has been identified as an unmet clinical need. Here, we report the first clinical trial of a third-generation leishmaniasis vaccine, developed intentionally to induce Leishmania-specific CD8+ T cells. We conducted a first-in-human dose escalation Phase I trial in 20 healthy volunteers to assess the safety, tolerability and immunogenicity of a prime-only adenoviral vaccine for human VL and PKDL. ChAd63-KH is a replication defective simian adenovirus expressing a novel synthetic gene (KH) encoding two Leishmania proteins KMP-11 and HASPB. Uniquely, the latter was engineered to reflect repeat domain polymorphisms and arrangements identified from clinical isolates. We monitored innate immune responses by whole blood RNA-Seq and antigen specific CD8+ T cell responses by IFNγ ELISPOT and intracellular flow cytometry. ChAd63-KH was safe at intramuscular doses of 1x1010 and 7.5x1010 vp. Whole blood transcriptomic profiling indicated that ChAd63-KH induced innate immune responses characterized by an interferon signature and the presence of activated dendritic cells. Broad and quantitatively robust CD8+ T cell responses were induced by vaccination in 100% (20/20) of vaccinated subjects. The results of this study support the further development of ChAd63-KH as a novel third generation vaccine for VL and PKDL. This clinical trial (LEISH1) was registered at EudraCT (2012-005596-14) and ISRCTN (07766359).

Porphyrins as Corrosion Inhibitors for N80 Steel in 3.5% NaCl Solution: Electrochemical, Quantum Chemical, QSAR and Monte Carlo Simulations Studies.

PubMed

Singh, Ambrish; Lin, Yuanhua; Quraishi, Mumtaz A; Olasunkanmi, Lukman O; Fayemi, Omolola E; Sasikumar, Yesudass; Ramaganthan, Baskar; Bahadur, Indra; Obot, Ime B; Adekunle, Abolanle S; Kabanda, Mwadham M; Ebenso, Eno E

2015-08-18

The inhibition of the corrosion of N80 steel in 3.5 wt. % NaCl solution saturated with CO2 by four porphyrins, namely 5,10,15,20-tetrakis(4-hydroxyphenyl)-21H,23H-porphyrin (HPTB), 5,10,15,20-tetra(4-pyridyl)-21H,23H-porphyrin (T4PP), 4,4',4″,4‴-(porphyrin-5,10,15,20-tetrayl)tetrakis(benzoic acid) (THP) and 5,10,15,20-tetraphenyl-21H,23H-porphyrin (TPP) was studied using electrochemical impedance spectroscopy (EIS), potentiodynamic polarization, scanning electrochemical microscopy (SECM) and scanning electron microscopy (SEM) techniques. The results showed that the inhibition efficiency, η% increases with increasing concentration of the inhibitors. The EIS results revealed that the N80 steel surface with adsorbed porphyrins exhibited non-ideal capacitive behaviour with reduced charge transfer activity. Potentiodynamic polarization measurements indicated that the studied porphyrins acted as mixed type inhibitors. The SECM results confirmed the adsorption of the porphyrins on N80 steel thereby forming a relatively insulated surface. The SEM also confirmed the formation of protective films of the porphyrins on N80 steel surface thereby protecting the surface from direct acid attack. Quantum chemical calculations, quantitative structure activity relationship (QSAR) were also carried out on the studied porphyrins and the results showed that the corrosion inhibition performances of the porphyrins could be related to their EHOMO, ELUMO, ω, and μ values. Monte Carlo simulation studies showed that THP has the highest adsorption energy, while T4PP has the least adsorption energy in agreement with the values of σ from quantum chemical calculations.

Embankment Criteria and Performance Report, Red River Watershed, Dierks Lake, Saline River, Arkansas

DTIC Science & Technology

1987-10-01

S’NDED.GL Report //22 7 i- -- , -- "-. . II _I IJ 12- ic d-- --- - ic diaete mol S-~---- ------ ,-- ..... .. .. . \\ \\...c u~ ton t _________ ’ blv e aho 3 lyr...2 2 NeMA STE.0 T/39 I 8 10T 211 122 7 -q- - 2 NORMA TRTI e1 .538 FT 5410 .56 125 . 5 e I F ~WATER CONTENT. % wo 2 9. 2 9. j Dr- DENSITY . 1.0LaCU...e n o ld d MIM) N. SQUARE 5 N. TH IC CLSS CATON Ca e SAND ( ) 3 .23 3 _____~~FILRE MINO _ _ (P G 0 - - -_ __ _ PROE ICt UILRKS 00A1 . ST AREA TYPE

Shipyard Marking Methods

DTIC Science & Technology

1980-09-01

K ( 7 ) D , SOAPSTONE ( 1 3 ) E. lNK (5) F. CRAYON OR PAINT STICK (14) G.DYE (1) H . PE N C I L ( 1 ) 1. ELECTRIC ENGRAVING (1) 2. WHO MANUFACTURES...CHALK ( 2 ) D . DYE (1) H, SOAPSTONE (4) 4. W HAT TYPE OF DISPENSING METHOD IS UTILIZED WITH MARKING MATERIALS? A . BALL POINT TUBE ( 1 3 ) H , STEEL...9 ) L, BAMBOO PEN & INK POT F. SOAPSTONE (12) M . OIL PENCIL ( 1 ) G . L A C S T I C K ( 0 ) N . ELECTRI c ENGRAVER (1) 5, ARE STANDARD COLORS

Optimization of polyhydroxybutyrate production by Bacillus sp. CFR 256 with corn steep liquor as a nitrogen source.

PubMed

Vijayendra, S V N; Rastogi, N K; Shamala, T R; Anil Kumar, P K; Kshama, L; Joshi, G J

2007-06-01

Polyhydroxyalkanotes (PHAs), the eco-friendly biopolymers produced by many bacteria, are gaining importance in curtailing the environmental pollution by replacing the non-biodegradable plastics derived from petroleum. The present study was carried out to economize the polyhydroxybutyrate (PHB) production by optimizing the fermentation medium using corn steep liquor (CSL), a by-product of starch processing industry, as a cheap nitrogen source, by Bacillus sp. CFR 256. Response surface methodology (RSM) was used to optimize the fermentation medium using the variables such as corn steep liquor (5-25 g l(-1)), Na(2)HPO(4) 2H(2)O (2.2-6.2 g l(-1)), KH(2)PO(4) (0.5-2.5 g l(-1)), sucrose (5-55 g l(-1)) and inoculum concentration (1-25 ml l(-1)). Central composite rotatable design (CCRD) experiments were carried out to study the complex interactions of the variables.The optimum conditions for maximum PHB production were (g l(-1)): CSL-25, Na(2)HPO(4) 2H(2)O-2.2, KH(2)PO(4) - 0.5, sucrose - 55 and inoculum - 10 (ml l(-1)). After 72 h of fermentation, the amount of PHA produced was 8.20 g l(-1) (51.20% of dry cell biomass). It is the first report on optimization of fermentation medium using CSL as a nitrogen source, for PHB production by Bacillus sp.

Ultrasensitive Infrared Chemiluminescence Detection

DTIC Science & Technology

1993-10-01

avelengt (14M) 2.01 1 NO Fundamental (Av-2) 2-0 3-1 S1.0 N(WA.fl Ŕ 4-1 5-2 0.0 2.0 2.5 3.0 3.5 4.0 Wavelength (urn) 42 NX -in Nowo cc E 0 Imt 𔃺 poz ow...2 p _4S) 347 nm INTENSITY AS A FUNCTION OF [N( 2 P)] T-5216 3.0 2.5 - 2.0- •. 1.5’- 0. S1.0 0.5 0.0 0 1 2 3 4 5 6 7 [N(2P)J (1011 atoms cm-3) 8-74M...observing the forbidden N( 2P- 4S) emission at 347 nm. The rate coefficient for N(ZP) quenching by 02 is (2.2 *0.4) x 10 cm3 molecule-I s-I and that

75 FR 6627 - Stainless Steel Sheet and Strip in Coils From Mexico; Final Results of Antidumping Duty...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-10

... between 0.20 and 0.80 percent manganese. This steel also contains, by weight, phosphorus of 0.025 percent... 19 and 22 percent, aluminum of no less than 5.0 percent, phosphorus of no more than 0.045 percent..., manganese, silicon and molybdenum each comprise, by weight, 0.05 percent or less, with phosphorus and sulfur...

75 FR 81214 - Stainless Steel Sheet and Strip in Coils From Italy: Preliminary Results of the Full Second Five...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-27

... between 0.20 and 0.80 percent manganese. This steel also contains, by weight, phosphorus of 0.025 percent... 19 and 22 percent, aluminum of no less than 5.0 percent, phosphorus of no more than 0.045 percent..., manganese, silicon and molybdenum each comprise, by weight, 0.05 percent or less, with phosphorus and sulfur...

Effect of dark chocolate on plasma epicatechin levels, DNA resistance to oxidative stress and total antioxidant activity in healthy subjects.

PubMed

Spadafranca, A; Martinez Conesa, C; Sirini, S; Testolin, G

2010-04-01

Dark chocolate (DC) may be cardioprotective by antioxidant properties of flavonoids. We investigated the effect of DC (860 mg polyphenols, of which 58 mg epicatechin) compared with white chocolate (WC; 5 mg polyphenols, undetectable epicatechin) on plasma epicatechin levels, mononuclear blood cells (MNBC) DNA damage and plasma total antioxidant activity (TAA). Twenty healthy subjects followed a balanced diet (55 % of energy from carbohydrates, 30 % from fat and 1 g protein/kg body weight) for 4 weeks. Since the 14th day until the 27th day, they introduced daily 45 g of either WC (n 10) or DC (n 10). Whole experimental period was standardised in antioxidant intake. Blood samples were collected at T(0), after 2 weeks (T(14)), 2 h and 22 h after the first chocolate intake (T(14+2 h) and T(14+22 h)), and at 27th day, before chocolate intake (T(27)), 2 h and 22 h after (T(27+2 h) and T(27+22 h)). Samples, except for T(14+2 h) and T(27+2 h), were fasting collected. Detectable epicatechin levels were observed exclusively 2 h after DC intake (T(14+2 h) = 0.362 (se 0.052) micromol/l and T(27+2 h) = 0.369 (se 0.041) micromol/l); at the same times corresponded lower MNBC DNA damages (T(14+2 h) = - 19.4 (se 3.4) % v. T(14), P < 0.05; T(27+2 h) = - 24 (se 7.4) % v. T(27), P < 0.05; T(14+2 h) v. T(27+2 h), P = 0.7). Both effects were no longer evident after 22 h. No effect was observed on TAA. WC did not affect any variable. DC may transiently improve DNA resistance to oxidative stress, probably for flavonoid kinetics.

Gastric and hepatocellular carcinomas do not overexpress the same ribosomal protein messenger RNAs as colonic carcinoma.

PubMed

Barnard, G F; Staniunas, R J; Mori, M; Puder, M; Jessup, M J; Steele, G D; Chen, L B

1993-09-01

The levels of a number of ribosomal protein mRNAs are reported to be increased in human colon cancer. We have assessed whether selected ribosomal protein mRNAs are overexpressed in other gastrointestinal malignancies, namely gastric and hepatocellular carcinomas. Subtracted complementary DNA libraries were generated from paired samples of human (a) colorectal carcinoma minus adjacent normal colonic mucosa and (b) hepatocellular carcinoma minus adjacent normal liver. Screening of approximately 3% of these library clones determined that ribosomal protein mRNAs encoding L18 and L37 (not previously reported) and P0 and S6 were overexpressed in one or the other library. Their complementary DNA inserts were then used as probes to evaluate their expression in a larger number of paired tumor/normal surgical samples of human colonic, gastric, and hepatocellular carcinomas, by Northern hybridization. The mRNA signal was greater in the colonic carcinoma than in paired adjacent normal colonic mucosa in 38 of 42 cases for P0 [tumor/normal (T/N) ratio = 3.0 +/- 0.3, mean +/- SE, P < 0.001] (G. F. Barnard, R. J. Staniunas, S. Bao, K. Mafune, J. L. Gollan, G. D. Steele, Jr., and L. B. Chen, Cancer Res., 52: 3067-3072, 1992), in 25 of 28 cases for L18 (T/N ratio = 3.7 +/- 0.5, P < 0.001), in 27 of 28 cases for L37 (T/N ratio = 5.3 +/- 0.4, P < 0.001), and in 24 of 28 cases for S6 (T/N ratio = 3.1 +/- 0.5, P < 0.01). The level of mRNA overexpression of L18 and S6 did not correlate with the Dukes' stage of disease. In hepatocellular carcinoma samples, using the same four ribosomal protein complementary DNA probes, only P0 mRNA was significantly increased (T/N ratio = 2.8 +/- 0.4, n = 6, P = 0.047). In gastric carcinoma samples, none of these mRNAs was increased (mean T/N ratios = 0.9-1.2, n = 6). Therefore, gastric and hepatocellular carcinomas do not overexpress the same ribosomal protein mRNAs as do colonic carcinoma.

MESSENGER Orbital Observations of Large-Amplitude Kelvin-Helmholtz Waves at Mercury's Magnetopause

NASA Technical Reports Server (NTRS)

Sundberg, Torbjorn; Boardsen, Scott A.; Slavin, James A.; Anderson, Brian J.; Korth, Haje; Zurbuchen, Thomas H.; Raines, Jim M.; Solomon, Sean C.

2012-01-01

We present a survey of Kelvi\\ n-Helmholtz (KH) waves at Mercury's magnetopause during MESSENGER's first Mercury year in orb it. The waves were identified on the basis of the well-established sawtooth wave signatures that are associated with non-linear KH vortices at the magnetopause. MESSENGER frequently observed such KH waves in the dayside region of the magnetosphere where the magnetosheath flow velocity is still sub -sonic, which implies that instability growth rates at Mercury's magnetopau are much larger than at Earth. We attribute these greater rates to the limited wave energy dissipation in Mercury's highly resistive regolith. The wave amplitude was often on the order of ' 00 nT or more, and the wave periods were - 10- 20 s. A clear dawn-dusk asymmetry is present in the data, in that all of the observed wave events occurred in the post-noon and dusk-side sectors of the magnetopause. This asymmetry is like ly related to finite Larmor-radius effects and is in agreement with results from particle-in-cell simulations of the instability. The waves were observed almost exclusively during periods when the north-south component of the magnetosheath magnetic field was northward, a pattern similar to that for most terrestrial KH wave events. Accompanying plasma measurements show that the waves were associated with the transport of magnetosheath plasma into the magnetosphere.

Electrogenerated chemiluminescence of tris(2-phenylpyridine)iridium(III) in water, acetonitrile and trifluorethanol.

PubMed

Robinson, Wesley D; Richter, Mark M

2015-02-01

The spectroscopic, electrochemical and coreactant electrogenerated chemiluminescence (ECL) properties of Ir(ppy)3 (where ppy = 2-phenylpyridine) have been obtained in aqueous buffered (KH2PO4), 50 : 50 (v/v) acetonitrile-aqueous buffered (MeCN-KH2PO4) and 30% trifluoroethanol (TFE) solutions. Tri-n-propylamine was used as the oxidative-reductive ECL coreactant. The photoluminescence (PL) efficiency (ϕem) of Ir(ppy)3 in TFE (ϕem ≈ 0.029) was slightly higher than in 50 : 50 MeCN-KH2PO4 (ϕem ≈ 0.0021) and water (ϕem ≈ 0.00016) compared to a Ru(bpy)32+ standard solution in water (Φem ≈ 0.042). PL and ECL emission spectra were nearly identical in all three solvents, with dual emission maxima at 510 and 530 nm. The similarity between the ECL and PL spectra indicate that the same excited state is probably formed in both experiments. ECL efficiencies (ϕecl) in 30% TFE solution (ϕecl = 0.0098) were higher than aqueous solution (ϕecl = 0.00092) system yet lower than a 50% MeCN-KH2PO4 solution (ϕecl = 0.0091). Copyright © 2014 John Wiley & Sons, Ltd.

Resistance to Reperfusion Injury Following Short Term Postischemic Administration of Natural Honey in Globally Ischemic Isolated Rat Heart

PubMed Central

Vaez, Haleh; Samadzadeh, Mehrban; Zahednezhad, Fahimeh; Najafi, Moslem

2012-01-01

Purpose: Results of our previous study revealed that preischemic perfusion of honey before zero flow global ischemia had cardioprotective effects in rat. The present study investigated potential resistance to reperfusion injury following short term postischemic administration of natural honey in globally ischemic isolated rat heart. Methods: Male Wistar rats were divided into five groups (n=10-13). The rat hearts were isolated, mounted on a Langendorff apparatus, allowed to equilibrate for 30 min then subjected to 30 min global ischemia. In the control group, the hearts were reperfused with drug free normal Krebs-Henseleit (K/H) solution before ischemia and during 120 min reperfusion. In the treatment groups, reperfusion was initiated with K/H solution containing different concentration of honey (0.25, 0.5, 1 and 2%) for 15 min and was resumed until the end of 120 min with normal K/H solution. Results: In the control group, VEBs number was 784±199, while in honey concentration of 0.25, 0.5, 1 and 2%, it decreased to 83±23 (P<0.001), 138±48 (P<0.01), 142±37 (P<0.001) and 157±40 (P<0.01), respectively. Number and duration of VT and time spent in reversible VF were also reduced by honey. In the control group, the infarct size was 54.1±7.8%, however; honey (0.25, 0.5, 1 and 2%) markedly lowered the value to 12.4±2.4, 12.7±3.3, 11.3±2.6 and 7.9±1.7 (P<0.001), respectively. Conclusion: Postischemic administration of natural honey in global ischemia showed protective effects against ischemia/reperfusion (I/R) injuries in isolated rat heart. Antioxidant and radical scavenging activity, lipoperoxidation inhibition, reduction of necrotized tissue, presence of rich energy sources, various type of vitamins, minerals and enzymes and formation of NO-contain metabolites may probably involve in those cardioprotective effects. PMID:24312792

Identification of two novel mammalian genes establishes a subfamily of KH-domain RNA-binding proteins.

PubMed

Makeyev, A V; Liebhaber, S A

2000-08-01

We have identified two novel human genes encoding proteins with a high level of sequence identity to two previously characterized RNA-binding proteins, alphaCP-1 and alphaCP-2. Both of these novel genes, alphaCP-3 and alphaCP-4, are predicted to encode proteins with triplicated KH domains. The number and organization of the KH domains, their sequences, and the sequences of the contiguous regions are conserved among all four alphaCP proteins. The common evolutionary origin of these proteins is substantiated by conservation of exon-intron organization in the corresponding genes. The map positions of alphaCP-1 and alphaCP-2 (previously reported) and those of alphaCP-3 and alphaCP-4 (present report) reveal that the four alphaCP loci are dispersed in the human genome; alphaCP-3 and alphaCP-4 mapped to 21q22.3 and 3p21, and the respective mouse orthologues mapped to syntenic regions of the mouse genome, 10B5 and 9F1-F2, respectively. Two additional loci in the human genome were identified as alphaCP-2 processed pseudogenes (PCBP2P1, 21q22.3, and PCBP2P2, 8q21-q22). Although the overall levels of alphaCP-3 and alphaCP-4 mRNAs are substantially lower than those of alphaCP-1 and alphaCP-2, transcripts of alphaCP-3 and alphaCP-4 were found in all mouse tissues tested. These data establish a new subfamily of genes predicted to encode closely related KH-containing RNA-binding proteins with potential functions in posttranscriptional controls. Copyright 2000 Academic Press.

A Converter for Producing a Hydrogen-Containing Synthesis Gas

NASA Astrophysics Data System (ADS)

Malkov, Yu. P.; Molchanov, O. N.; Britov, B. K.; Fedorov, I. A.

2016-11-01

A computational thermodynamic and experimental investigation of the characteristics of a model of a converter for producing a hydrogen-containing synthesis gas from a hydrocarbon fuel (kerosene) with its separate delivery to thermal-oxidative and steam conversions has been carried out. It is shown that the optimum conditions of converter operation correspond to the oxidant excess coefficient in the converter's combustion chamber α > 0.5 at a temperature of the heat-transmitting wall (made from a heat-resistant KhN78T alloy (ÉI 435)) of 1200 K in the case of using a nickel corrugated tape catalyst. The content of hydrogen in the synthesis gas attains in this case 60 vol.%, and there is no release of carbon (soot) in the conversion products as well as no need for water cooling of the converter walls.

Effect of neutron irradiation at low temperature on the embrittlement of the reduced-activation ferritic steels

NASA Astrophysics Data System (ADS)

Rybin, V. V.; Kursevich, I. P.; Lapin, A. N.

1998-10-01

Effects of neutron irradiation to fluence of 2.0 × 10 24 n/m 2 ( E > 0.5 MeV) in temperature range 70-300°C on mechanical properties and structure of the experimental reduced-activation ferritic 0.1%C-(2.5-12)%Cr-(1-2)%W-(0.2-0.7)%V alloys were investigated. The steels were studied in different initial structural conditions obtained by changing the modes of heat treatments. Effect of neutron irradiation estimated by a shift in ductile-brittle transition temperature (ΔDBTT) and reduction of upper shelf energy (ΔUSE) highly depends on both irradiation condition and steel chemical composition and structure. For the steel with optimum chemical composition (9Cr-1.5WV) after irradiation to 2 × 10 24 n/m 2 ( E ⩾ 0.5 MeV) at 280°C the ΔDBTT does not exceed 25°C. The shift in DBTT increased from 35°C to 110°C for the 8Cr-1.5WV steel at a decrease in irradiation temperature from 300°C to 70°C. The CCT diagrams are presented for several reduced-activated steels.

High degree of BMI misclassification of malnutrition among Swedish elderly population: Age-adjusted height estimation using knee height and demispan

PubMed Central

Gavriilidou, N N; Pihlsgård, M; Elmståhl, S

2015-01-01

Background/Objectives: The degree of misclassification of obesity and undernutrition among elders owing to inaccurate height measurements is investigated using height predicted by knee height (KH) and demispan equations. Subjects/Methods: Cross-sectional investigation was done among a random heterogeneous sample from five municipalities in Southern Sweden from a general population study ‘Good Aging in Skåne' (GÅS). The sample comprised two groups: group 1 (KH) including 2839 GÅS baseline participants aged 60–93 years with a valid KH measurement and group 2 (demispan) including 2871 GÅS follow-up examination participants (1573 baseline; 1298 new), aged 60–99 years, with a valid demispan measurement. Participation rate was 80%. Height, weight, KH and demispan were measured. KH and demispan equations were formulated using linear regression analysis among participants aged 60–64 years as reference. Body mass index (BMI) was calculated in kg/m2. Results: Undernutrition prevalences in men and women were 3.9 and 8.6% by KH, compared with 2.4 and 5.4% by standard BMI, and more pronounced for all women aged 85+ years (21% vs 11.3%). The corresponding value in women aged 85+ years by demispan was 16.5% vs 10% by standard BMI. Obesity prevalences in men and women were 17.5 and 14.6% by KH, compared with 19.0 and 20.03% by standard BMI. Values among women aged 85+ years were 3.7% vs 10.4% by KH and 6.5% vs 12.7% by demispan compared with the standard. Conclusions: There is an age-related misclassification of undernutrition and obesity attributed to inaccurate height estimation among the elderly. This could affect the management of patients at true risk. We therefore propose using KH- and demispan-based formulae to address this issue. PMID:25205322

Characterization of Hot Deformation Behavior of a Fe-Cr-Ni-Mo-N Superaustenitic Stainless Steel Using Dynamic Materials Modeling

NASA Astrophysics Data System (ADS)

Pu, Enxiang; Zheng, Wenjie; Song, Zhigang; Feng, Han; Zhu, Yuliang

2017-03-01

Hot deformation behavior of a Fe-24Cr-22Ni-7Mo-0.5N superaustenitic stainless steel was investigated by hot compression tests in a wide temperature range of 950-1250 °C and strain rate range of 0.001-10 s-1. The flow curves show that the flow stress decreases as the deformation temperature increases or the strain rate decreases. The processing maps developed on the basis of the dynamic materials model and flow stress data were adopted to optimize the parameters of hot working. It was found that the strain higher than 0.2 has no significant effect on the processing maps. The optimum processing conditions were in the temperature range of 1125-1220 °C and strain rate range of 0.1-3 s-1. Comparing to other stable domains, microstructural observations in this domain revealed the complete dynamic recrystallization (DRX) with finer and more uniform grain size. Flow instability occurred in the domain of temperature lower than 1100 °C and strain rate higher than 0.1 s-1.

Phosphorus bioavailability, true metabolizable energy, and amino acid digestibilities of high protein corn distillers dried grains and dehydrated corn germ.

PubMed

Kim, E J; Amezcua, C Martinez; Utterback, P L; Parsons, C M

2008-04-01

There is currently much ongoing research and interest for developing new processing technologies to produce corn distillers dried grains with solubles (DDGS). The current study evaluated a high protein (HP) distillers dried grains (DDG) and a dehydrated corn germ, which are products that can be produced by a modified dry milling process. Two chick experiments were conducted to determine the P bioavailability based on tibia ash. In addition, precision-fed rooster assays were conducted to determine TME(n) and amino acid digestibility. In the first chick assay, a P-deficient cornstarch-dextrose-soybean meal basal diet containing 0.10 to 0.13% nonphytate P was supplemented with 0.0, 0.05, and 0.10% P from KH(2)PO(4) or 7 and 14% conventional DDGS, HP DDG, and corn germ. In the second experiment, the P-deficient basal was supplemented with 7 and 14% conventional DDGS and 12.5 and 25% HP DDG. New Hampshire x Columbian female chicks were fed the experimental diets from 9 to 22 d posthatch, and bioavailability of P was estimated using the slope-ratio method where tibia ash was regressed on P intake. The total P content (90% DM basis) of the conventional DDGS, HP DDG, and corn germ were 0.76, 0.33, and 1.29%, respectively. Bioavailabilities of the P in conventional DDGS, HP DDG, and corn germ relative to KH(2)PO(4) were found to be 60, 56, and 25%, respectively. The TME(n) in conventional roosters was found to be significantly reduced for HP DDG and increased for the corn germ when compared with the conventional DDGS. The protein content (90% DM basis) of the HP DDG and corn germ was 33 and 14%, respectively, and the total lysine as a % of CP was approximately 2 times greater for the corn germ than for the HP DDG. Amino acid digestibilities in cecectomized roosters were consistently higher for the corn germ than for the HP DDG, which was similar to conventional DDGS.

Software Reliability Estimation under Conditions of Incomplete Information.

DTIC Science & Technology

1979-10-01

6k) 1 I’a 1 aN+6d (k D N ae a a m a m where ae i Jl i-rnm ae Mem 0 i~m and -A.7- I pop ," -, (L 0 a o\\ a a(0 0 a) ( T n +L L0- (k0 B2 e e aL (0 -TA...zLLki2ZLK22 9o 10 LuNTINUL 97 METURN -D.7- I ,u~t(OUTLiNE H.TA(ABPeNA.T#VvRRPJJJ) .5 mEAL*b toA 𔃾 HLAL kAeX~ oHP #RNiAtR7#DPRZ thEAL RO a Ia$GL(hiR) Kb

Estimation of the Temperature-Dependent Nitrogen Solubility in Stainless Fe-Cr-Mn-Ni-Si-C Steel Melts During Processing

NASA Astrophysics Data System (ADS)

Wendler, Marco; Hauser, Michael; Sandig, Eckhard Frank; Volkova, Olena

2018-04-01

The influence of chemical composition, temperature, and pressure on the nitrogen solubility of various high alloy stainless steel grades, namely Fe-14Cr-(0.17-7.77)Mn-6Ni-0.5Si-0.03C [wt pct], Fe-15Cr-3Mn-4Ni-0.5Si-0.1C [wt pct], and Fe-19Cr-3Mn-4Ni-0.5Si-0.15C [wt pct], was studied in the melt. The temperature-dependent N-solubility was determined using an empirical approach proposed by Wada and Pehlke. The thus calculated N-concentrations overestimate the actual N-solubility of all the studied Fe-Cr-Mn-Ni-Si-C steel melts at a given temperature and pressure. Consequently, the calculation model has to be modified by Si and C because both elements are not recognized in the original equation. The addition of the 1st and 2nd order interaction parameters for Si and C to the model by Wada and Pehlke allows a precise estimation of the temperature-dependent nitrogen solubility in the liquid steel bath, and fits very well with the measured nitrogen concentrations during processing of the steels. Moreover, the N-solubility enhancing effect of Cr- and Mn-additions has been demonstrated.

Vehicle Noise Measurements.

DTIC Science & Technology

1980-04-01

TEST: ’? REC. FREQ. SPEC. INRL. BW ENGINE SPEED ANTENNI S TI)N 71 MHz 30 kH: 1500 RPM 0 dog. 3 N. MEASURED APD VALUES: PoiMt P b. PCo S . C&I . RMS Vb.,g...PROBiM8 IL ITY F8 S TEST CO’DE 11 .6881 sew6 .681 .01 .02 805 1 .2 .3 .4 Apo osuv v) ERs1 .s F~oeABIL1TY FR eW TEST CODE 2 5 4 40 .0001 am68 .681 .61 .62

Abdominopelvic 1.5-T and 3.0-T MR Imaging in Healthy Volunteers: Relationship to Formation of DNA Double-Strand Breaks.

PubMed

Suntharalingam, Saravanabavaan; Mladenov, Emil; Sarabhai, Theresia; Wetter, Axel; Kraff, Oliver; Quick, Harald H; Forsting, Michael; Iliakis, Georg; Nassenstein, Kai

2018-05-01

Purpose To investigate the relationship between abdominopelvic magnetic resonance (MR) imaging and formation of DNA double-strand breaks (DSBs) in peripheral blood lymphocytes among a cohort of healthy volunteers. Materials and Methods Blood samples were obtained from 40 healthy volunteers (23 women and 17 men; mean age, 27.2 years [range, 21-37 years]) directly before and 5 and 30 minutes after abdominopelvic MR imaging performed at 1.5 T (n = 20) or 3.0 T (n = 20). The number of DNA DSBs in isolated blood lymphocytes was quantified after indirect immunofluorescent staining of a generally accepted DSB marker, γ-H2AX, by means of high-throughput automated microscopy. As a positive control of DSB induction, blood lymphocytes from six volunteers were irradiated in vitro with x-rays at a dose of 1 Gy (70-90 keV). Statistical analysis was performed by using a Friedman test. Results No significant alteration in the frequency of DNA DSB induction was observed after MR imaging (before imaging: 0.22 foci per cell, interquartile range [IQR] = 0.54 foci per cell; 5 minutes after MR imaging: 0.08 foci per cell, IQR = 0.39 foci per cell; 30 minutes after MR imaging: 0.09 foci per cell, IQR = 0.63 foci per cell; P = .057). In vitro radiation of lymphocytes with 1 Gy led to a significant increase in DSBs (0.22 vs 3.43 foci per cell; P = .0312). The frequency of DSBs did not differ between imaging at 1.5 T and at 3.0 T (5 minutes after MR imaging: 0.23 vs 0.06 foci per cell, respectively [P = .57]; 30 minutes after MR imaging: 0.12 vs 0.08 foci per cell [P = .76]). Conclusion Abdominopelvic MR imaging performed at 1.5 T or 3.0 T does not affect the formation of DNA DSBs in peripheral blood lymphocytes. © RSNA, 2018.

75 FR 62104 - Certain Stainless Steel Sheet and Strip in Coils From Germany, Japan, the Republic of Korea, and...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-07

... also contains, by weight, phosphorus of 0.025 percent or less, silicon of between 0.20 and 0.50 percent..., chromium of between 19 and 22 percent, aluminum of no less than 5.0 percent, phosphorus of no more than 0... percent or less, with phosphorus and sulfur each comprising, by weight, 0.03 percent or less. This steel...

75 FR 81221 - Stainless Steel Sheet and Strip in Coils From Mexico; Preliminary Results of the Five-Year...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-27

... also contains, by weight, phosphorus of 0.025 percent or less, silicon of between 0.20 and 0.50 percent..., chromium of between 19 and 22 percent, aluminum of no less than 5.0 percent, phosphorus of no more than 0... percent or less, with phosphorus and sulfur each comprising, by weight, 0.03 percent or less. This steel...

Corrosion of stainless steels in lead-bismuth eutectic up to 600 °C

NASA Astrophysics Data System (ADS)

Soler, L.; Martín, F. J.; Hernández, F.; Gómez-Briceño, D.

2004-11-01

An experimental program has been carried out to understand the differences in the corrosion behaviour between different stainless steels: the austenitic steels 304L and 316L, the martensitic steels F82Hmod, T91 and EM10, and the low alloy steel P22. The influence of oxygen level in Pb-Bi, temperature and exposure time is studied. At 600 °C, the martensitic steels and the P22 steel exhibit thick oxide scales that grow with time, following a linear law for the wet environment and a parabolic law for the dry one. The austenitic stainless steels show a better corrosion behaviour, especially AISI 304L. Under reducing conditions, the steels exhibit dissolution, more severe for the austenitic stainless steels. At 450 °C, all the materials show an acceptable behaviour provided a sufficient oxygen level in the Pb-Bi. At reducing conditions, the martensitic steels and the P22 steel have a good corrosion resistance, while the austenitic steels exhibit already dissolution at the longer exposures.

Current Methodologies for the Analysis of Contingency Tables: Robustness with Respect to Small Expected Values.

DTIC Science & Technology

1982-06-09

40 @ "o VAi %P t 00493f "f t0 IVI Ř "f %,?I 0N% &p &~9. - 4F.904 S d @ 4P099 4U d 909@ 00F 99@ 5 44%4#f m 999F.490F~pPd.5 WAPd 040Pdp.4Pd44090095...64 គ 67 22 21 63 គ 51 18 51 គ ’-, IS N -- -. - . . . . . . . . . - .. .. - .. - 71 264 MINIMUM N (N) TABLE: 2 x5 .10__ .05 .01 VECTOR K P G K P...the Use and Interpretation of Certain Test Cviteria for the Purpose of Statistical Inference, Part II", Biometrika, 20, 264 -299. Odoroff, C. L. (1970

Surface modification of silicon carbide with silane coupling agent and hexadecyl iodiele

NASA Astrophysics Data System (ADS)

Shang, Xujing; Zhu, Yumei; Li, Zhihong

2017-02-01

In this paper, two kinds of silane coupling agents, namely 3-aminopropyl triethoxysilane (KH550) and 3-mercaptopropyl trimethoxysilane (KH590), were adopted as preliminary modifiers to improve the hydrophobic surface properties of silicon carbide (SiC) powder for the first step. The factors that influence the modification effects were investigated by measuring the contact angle. The results showed that KH590 has a better effect than KH550 for the hydrophobic modification of SiC, and the contact angle improved most after SiC powder was reacted with 0.3 g KH590 at 75 °C in aqueous/alcohol solution for 4 h. On account of further enhancement of hydrophobicity, the study was focused on utilizing nucleophilic substitution between KH590 and hexadecyl iodiele to extend the length of alkyl chain. Compared with using KH590 alone, SiC powder modified by KH590 and hexadecyl iodiele showed better water resistance with an increase of contact angle from 106.8° to 127.5°. The Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectra (XPS) as well as X-ray diffraction (XRD) analysis results showed that KH550/KH590 and hexadecyl iodiele can be covalently bonded to the surface of SiC powder without altering its crystal configuration. This methodology may provide a new way of the modification of inorganic materials in further.

Composite Material Repair and Reliability

DTIC Science & Technology

1989-03-01

BET TABLE 1 0.1 90 1 VIEW ID=I XVIEl=1 YVIE=0 ZVIEN=O EGZONE NAME=TTODSOLID 1/2 49 FR ~AME HEADING=UPPER XSF=1O0 YSF=O.5 XFMA)X=22.5 YFMAX=17.0 MESH...stiff 36 6 sig- no ;epsno -2E05; -6E-01 -5.713’ -0152 m 31 _ T_ ! 8E03: 7E-4 edx -2E-06! 0.001, ____ w/so 38 2 2E-03 6E-07 e/i 8E-04!- -0.001’:___ fn...U) nC 0 o00 coC 00 r- MO en ~ 0) mmr Nr fr W r4 W -4 .1m -4 N OM 0(1m tL m .- -t ’A LAMn %D 14LA ,-4 LA 0 0 00 00 00 00 00 00 0 0 %D4 O OW O W ow 0I

Microstructural analysis of hot press formed 22MnB5 steel

NASA Astrophysics Data System (ADS)

Aziz, Nuraini; Aqida, Syarifah Nur; Ismail, Izwan

2017-10-01

This paper presents a microstructural study on hot press formed 22MnB5 steel for enhanced mechanical properties. Hot press forming process consists of simultaneous forming and quenching of heated blank. The 22MnB5 steel was processed at three different parameter settings: quenching time, water temperature and water flow rate. 22MnB5 was processed using 33 full factorial design of experiment (DOE). The full factorial DOE was designed using three factors of quenching time, water temperature and water flow rate at three levels. The factors level were quenching time range of 5 - 11 s, water temperature; 5 - 27°C and water flow rate; 20 - 40 L/min. The as-received and hot press forming processed steel was characterised for metallographic study and martensitic structure area percentage using JEOL Field Emission Scanning Electron Microscopic (FESEM). From the experimental finding, the hot press formed 22MnB5 steel consisted of 50 to 84% martensitic structure area. The minimum quenching time of 8 seconds was required to obtain formed sample with high percentage of martensite. These findings contribute to initial design of processing parameters in hot press forming of 22MnB5 steel blanks for automotive component.

Effects of temperature, pH, and ionic strength on the Henry's law constant of triethylamine

NASA Astrophysics Data System (ADS)

Leng, Chun-Bo; Roberts, Jason E.; Zeng, Guang; Zhang, Yun-Hong; Liu, Yong

2015-05-01

The Henry's law constants (KH) of triethylamine (TEA) in pure water and in 1-octanol were measured for the temperatures pertinent to the lower troposphere (278-298 K) using a bubble column system coupled to a Fourier transform infrared spectrometer. The KH values of TEA in water and 1-octanol at 298 K are 5.75 ± 0.86 mol L-1 atm-1 and 115.62 ± 5.78 mol L-1 atm-1. The KH values display strong dependence on temperature, pH, and ionic strength. The characteristic times for TEA to establish an equilibrium between gas and droplet with a size of 5.6 µm are ~33 s (298 K, pH = 5.6); ~8.9 × 102 s (278 K, pH = 5.6); ~1.3 × 103 s (298 K, pH = 4.0); and 3.6 × 104 s (278 K, pH = 4.0). The evaluation of TEA partitioning between gas phase and condensed phase implies that TEA predominantly resides in rainwater, and TEA loss to organic aerosol is negligible.

Thermal Design of Boiler Unit (Standard Method).

DTIC Science & Technology

1980-04-29

T-0411-80" h EhlllllEI mhEhhhhh m~lEElhElllllE Elhllllllhllll llllllllmllllu llllllllhllllu "’FTD-ID(RS)T-0411-80 FOREIGN TECHNOLOGY DIVISION THERMAL...Block italic Transliter. - - A a A, a P p p p R, r S B, b C C S B V, v T m , t r g Y y SD, d SE a Ye, ye; E, e* x X x Kh, , W Zc h , z h L 4 Ti , L...sh sn arc_4n 6 ch cosh arc or -. tar. th tanh arc t- Scot zth cct arc c’- h sec Sch sech arc sc- . - o-ec csc cscn cs ch aronc sc Russian Er.I n h rot

Interaction between Marine-Derived n-3 Long Chain Polyunsaturated Fatty Acids and Uric Acid on Glucose Metabolism and Risk of Type 2 Diabetes Mellitus: A Case-Control Study.

PubMed

Li, Kelei; Wu, Kejian; Zhao, Yimin; Huang, Tao; Lou, Dajun; Yu, Xiaomei; Li, Duo

2015-08-26

The present case-control study explored the interaction between marine-derived n-3 long chain polyunsaturated fatty acids (n-3 LC PUFAs) and uric acid (UA) on glucose metabolism and risk of type 2 diabetes mellitus (T2DM). Two hundred and eleven healthy subjects in control group and 268 T2DM subjects in case group were included. Plasma phospholipid (PL) fatty acids and biochemical parameters were detected by standard methods. Plasma PL C22:6n-3 was significantly lower in case group than in control group, and was negatively correlated with fasting glucose (r = -0.177, p < 0.001). Higher plasma PL C22:6n-3 was associated with lower risk of T2DM, and the OR was 0.32 (95% confidence interval (CI), 0.12 to 0.80; p = 0.016) for per unit increase of C22:6n-3. UA was significantly lower in case group than in control group. UA was positively correlated with fasting glucose in healthy subjects, but this correlation became negative in T2DM subjects. A significant interaction was observed between C22:6n-3 and UA on fasting glucose (p for interaction = 0.005): the lowering effect of C22:6n-3 was only significant in subjects with a lower level of UA. In conclusion, C22:6n-3 interacts with UA to modulate glucose metabolism.

Effects of Trypanocidal Drugs on the Function of Trypanosomes.

DTIC Science & Technology

1978-09-01

trtod) -Odr__primary results during this past year are: a. 7 tbihdtosriso rpnooabue T rciETO10 n T. brucel 427) in vitro as cultured infective...A 174 .I A -V. A, A’ ~ ~ hA 4 T. brucel 0--a BERENIL TRE:ATEO, 5 mg/kg 0-4 CONTROL 20.0- 10.0: 8.0- 4 .0- 0 I- 1.0 - HOURS Figure 22 t7 d **VI Figure...URIDINE INCORPORATION 14- 12- CONTROL 0 E I- I- ETHIDIUM O BROMIDE 4 6 ANTRYCIDE 2 BERENIL SURAMIN 0 10 20 30 40 50 60 MINUTES Figure 29 T. brucel

A Comparative Study on Formability of the Third-Generation Automotive Medium-Mn Steel and 22MnB5 Steel

NASA Astrophysics Data System (ADS)

Zheng, Guojun; Li, Xiaodong; Chang, Ying; Wang, Cunyu; Dong, Han

2018-02-01

Third-generation advanced automotive medium-Mn steel, which can replace 22MnB5 steel, was newly developed to improve the lightweight and crashworthiness of automobile. Studies on the formability and simulation method of medium-Mn steel have just been initiated. In this study, finite element simulation models of square-cup deep drawing were established based on various material property experiments and validated by experiments. The effects of blank holder force (BHF), fillet radii of tools (die and punch) on the maximum drawing depth (MDD), thickness distribution of the formed products, and the microstructure before and after forming were investigated and compared with those on 22MnB5 steel. Results show that the MDD of the two steels decreased with increased BHF but increased with the fillet radius of punch; however, the fillet radius of die showed no significant effect on the MDD for both steels. Compared with hot-formed 22MnB5 steel, the martensitic transformation of the hot-formed medium-Mn steel is rarely influenced by the process parameters; thus, it holds the complete, fine-grained, and uniform martensitic microstructure. Moreover, the medium-Mn has better formability, lower initial blank temperature, and smaller impact of BHF and fillet radius of tools on the hot-formed product. Thus, a theoretical basis for the replacement of 22MnB5 steel by medium-Mn steel in hot forming process is provided.

Design and development of a hard tube flexible radiator system

NASA Technical Reports Server (NTRS)

Hixon, C. W.

1980-01-01

The construction and operational characteristics of an extended life flexible radiator panel is described. The radiator panel consists of a flexible fin laminate and stainless steel flow tubes designed for a 90 percent probability of surviving 5 years in an Earth orbit micrometeoroid environment. The radiator panel rejects 1.1 kW sub t of heat into an environmental sink temperature of 0 F. Total area is 170 square feet and the panel extends 25 feet in the fully deployed position. When retracted the panel rolls onto a 11.5 inch diameter by 52 inch long storage drum, for a final stored diameter of 22 inches.

Influence of Joint Configuration on the Strength of Laser Welded Presshardened Steel

NASA Astrophysics Data System (ADS)

Kügler, H.; Mittelstädt, C.; Vollertsen, F.

Presshardened steel is used in nowadays automotive production. Due to its high strength, sheet thicknesses can be reduced which results in decreasing weight of car body components. However, because of microstructure softening and coating agglomerations in the seam, welding is still a challenge. In this paper laser beam welding of 22MnB5 with varying energy input per irradiated area is presented. It is found that increasing energy input per seam length reduces tensile strength. Using a small spot size of 200 μm, tensile strength of 1434 N/mm2 can be reached in bead on plate welds. In lap welds tensile strength is limited because of coating particles agglomerating at the melt pool border line. However, the resulting strength is higher when using several small weld seams than using one seam with the same total seam width. With three weld seams, each 0.5mm in width, tensile strength of 911N/mm2 is reached in lap welding.

Finite Element Modelling Full Vehicle Side Impact with Ultrahigh Strength Hot Stamped Steels

NASA Astrophysics Data System (ADS)

Taylor, T.; Fourlaris, G.; Cafolla, J.

2016-10-01

"Hot stamped boron steel" 22MnB5 has been imperative in meeting the automotive industry's demand for materials exhibiting higher tensile strength in the final component. In this paper, the crash performance of three experimental grades developed for automotive hot stamping technologies, exhibiting wider tensile property ranges than 22MnB5, was validated by finite element modelling full vehicle side impact with the experimental material data applied to the B-pillar reinforcement. The superior anti-intrusive crash performance of grade 38MnB5 was demonstrated, with 11 mm less intrusion of the B-pillar reinforcement compared to 22MnB5. Moreover, the superior "impact-energy absorptive" crash performance of grade 15MnCr5 was demonstrated, with 0.15 kJ greater impact-energy absorption by the B-pillar reinforcement compared to 22MnB5.

Thermal properties of spin-S Kitaev-Heisenberg model on a honeycomb lattice

NASA Astrophysics Data System (ADS)

Suzuki, Takafumi; Yamaji, Youhei

2018-05-01

Temperature (T) dependence of heat capacity C (T) in the S = 1 / 2 Kitaev honeycomb model shows a double-peak structure resulting from fractionalization of spins into two kinds of Majorana fermions. Recently it has been discussed that the double-peak structure in C (T) is also observed in magnetic ordered phases of the S = 1 / 2 Kitaev-Heisenberg (KH) model on a honeycomb lattice when the system is located in the vicinity of the Kitaev's spin liquid phase. In addition to the S = 1 / 2 spin case, similar double-peak structure has been confirmed in the KH honeycomb model for classical Heisenberg spins, where spin S is regarded as S → ∞ . We investigate spin-S dependence of C (T) for the KH honeycomb models by using thermal pure quantum state. We also perform classical Monte Carlo calculations to obtain C (T) for the classical KH model. From obtained results, we find that the origin of the high-temperature peak is different between the quantum spin case with small Ss and the classical Heisenberg spin case. Furthermore, the high-temperature peak in the quantum spin case, which is one of the clues for fractionalization of spins, disappears for S > 1 .

Conceptual Knowledge Foundations for Naval Medical Training: A Scheme for Directed Curricular Planning and Instructional Design.

DTIC Science & Technology

1992-01-14

N00014-88-K-0286 (R&T4428014) Reproduction in whole or pai t is permitted for any purpose of the United States Government Approved for public release ...128.DISRIBTIO , AAILAILIY SATEENT12b. DISTRIBUTION CODE Approved for public release ; distribution unlimited. CX 13. ABSTRACT (Maximum 200 words) A...Structures 30 16.5 16.6 17.5 25.5* p<(.004 ) (e"g. esophagus) Substances 8 0.5 0.4 1.0 4.0 * p<(.0001) (e.g. gastrin ) Neuro-endo 6 0.5 0.2 0.5 2.2 * p<(.0008

Restricted L1 Estimators and Their Covariances,

DTIC Science & Technology

1980-06-01

CD22 w =e 1-.< l’ -- I -M Ce -=, -2 C 22 CD -. 00 CD LJ L":v, wD .-C >-C CD U., -D -a 22J CD: CD. Vt. U.1 . CD* 31- a UOC CD I" -J zI == CŖ - 1- InCC.J...C 22 CC:.: 2 15Cb In0’C C 4 t’ 3 CD.2-cm I- I.- iC2 CD-3SJ U. cc CDam CC 22 0.-J~ I- iD C Me CC .JJ . A.2 Dt-2C. 2. D ~ 2 CD, Z-i- C -J 2Cn LI CD22 ...22 "I.- bII CD 0.-..CW I -- k- -o. CDCD-c =DDCCC-ce CDI- 22eCCDC.C I-L- 5 2wI-CDUct. I4.CDgCD Ci L., 2=9 E Mm t,2 cm CD22 ,,- D.-.2RCC Ce:CD .Cc n 9

Strength of "Light" Ferritic and Austenitic Steels Based on the Fe - Mn - Al - C System

NASA Astrophysics Data System (ADS)

Kaputkina, L. M.; Svyazhin, A. G.; Smarygina, I. V.; Kindop, V. E.

2017-01-01

The phase composition, the hardness, the mechanical properties at room temperature, and the resistance to hot (950 - 1000°C) and warm (550°C) deformation are studied for cast deformable "light" ferritic and austenitic steels of the Fe - (12 - 25)% Mn - (0 - 15)% Al - (0 - 2)% C system alloyed additionally with about 5% Ni. The high-aluminum high-manganese low-carbon and carbonless ferritic steels at a temperature of about 0.5 T melt have a specific strength close to that of the austenitic steels and may be used as weldable scale-resistant and wear-resistant materials. The high-carbon Fe - (20 - 24)% Mn - (5 - 9)% Al - 5% Ni - 1.5% C austenitic steels may be applied as light high-strength materials operating at cryogenic temperatures after a solution treatment and as scale- and heat-resistant materials in an aged condition.

Propulsion and Energetics Panel Working Group 20 on Test Cases for Engine Life Assessment Technology (Cas d’Essai pour la Gestion de la Duree de Vie des Moteurs)

DTIC Science & Technology

1992-09-01

the 10 Figure 2.1 LARZAC ENGINE - welded disk-shaft 1 - shaft-spacer 2 -cone 3 - aft seal 4 - blades 5 Figure 2.2 COMPONENT GEOMETRY OEZ 0 9LL 0 It- C4...57 ൒--m-- 5.735 29.475 95 12.525 0.08 F60,45 chom at 456 -- - 6 1 Holes equall WIN 2,24! sae 80 T RIo.2 R838*20’ •-R2o4..6 0537,6 4 0640.226 R4...steel attempt was made Lo predict wire. Control thermocouples were initiation at the oil feed holes, welded to the compressor and since the stated goal of

Coastal groundwater dynamics off Santa Barbara, California: combining geochemical tracers, electromagnetic seepmeters, and electrical resistivity

USGS Publications Warehouse

Swarzenski, Peter W.; Izbicki, John A.

2009-01-01

This paper presents repeat field measurements of 222Rn and 223,224,226,228Ra, electromagnetic seepage meter-derived advective fluxes, and multi-electrode, stationary and continuous marine resistivity surveys collected between November 2005 and April 2007 to study coastal groundwater dynamics within a marine beach in Santa Barbara, California. The study provides insight into magnitude and dynamics of submarine groundwater discharge (SGD) and associated nutrient loadings into near-shore coastal waters, where the predominant SGD drivers can be both spatially and temporally separated. Rn-222 and 223,224,226,228Ra were utilized to quantify the total and saline contribution, respectively, of SGD. The two short-lived 224,223Ra isotopes provided an estimate of apparent near-shore water mass age, as well as an estimate of the Ra-derived eddy diffusion coefficient, Kh (224Ra = 2.86 ?? 0.7 m2 s-1; 223Ra = 1.32 ?? 0.5 m2 s-1). Because 222Rn (t1/2 = 3.8 day) and 224Ra (t1/2 = 3.66 day) have comparable half-lives and production terms, they were used in concert to examine respective water column removal rates. Electromagnetic seepage meters recorded the physical, bi-directional exchange across the sediment/water interface, which ranged from -6.7 to 14.5 cm day-1, depending on the sampling period and position relative to the low tide line. Multi-day time-series 222Rn measurements in the near-shore water column yielded total (saline + fresh) SGD rates that ranged from 3.1 ?? 2.6 to 9.2 ?? 0.8 cm day-1, depending on the sampling season. Offshore 226Ra (t1/2 = 1600 year) and 222Rn gradients were used with the calculated Kh values to determine seabed flux estimates (dpm m-2 day-1), which were then converted into SGD rates (7.1 and 7.9 cm day-1, respectively). Lastly, SGD rates were used to calculate associated nutrient loads for the near-shore coastal waters off Santa Barbara. Depending on both the season and the SGD method utilized, the following SGD-derived nutrient inputs were computed (mol per day per meter of shoreline): NH4+ = 0.06-0.29 mol day-1 m-1; SiO4 = 0.22-0.29 mol day-1 m-1; PO43-= 0.04-0.17 mol day-1 m-1; [NO2- + NO3-] = 0-0.52 mol day-1 m-1; dissolved inorganic nitrogen (DIN) = 0.01-0.17 mol day-1 m-1, and dissolved organic nitrogen (DON) = 0.08-0.09 mol day-1 m-1. Compared to the ephemeral nature of fluvial and marine inputs into this region, such SGD-derived loadings can provide a sustained source of select nutrients to the coastal waters off Santa Barbara, California that should be accounted for in mass balance estimates.

Causes of distal volcano-tectonic seismicity inferred from hydrothermal modeling

NASA Astrophysics Data System (ADS)

Coulon, C. A.; Hsieh, P. A.; White, R.; Lowenstern, J. B.; Ingebritsen, S. E.

2017-10-01

Distal volcano-tectonic (dVT) seismicity typically precedes eruption at long-dormant volcanoes by days to years. Precursory dVT seismicity may reflect magma-induced fluid-pressure pulses that intersect critically stressed faults. We explored this hypothesis using an open-source magmatic-hydrothermal code that simulates multiphase fluid and heat transport over the temperature range 0 to 1200 °C. We calculated fluid-pressure changes caused by a small (0.04 km3) intrusion and explored the effects of flow geometry (channelized vs. radial flow), magma devolatilization rates (0-15 kg/s), and intrusion depths (5 and 7.5 km, above and below the brittle-ductile transition). Magma and host-rock permeabilities were key controlling parameters and we tested a wide range of permeability (k) and permeability anisotropies (kh/kv), including k constant, k(z), k(T), and k(z, T, P) distributions, examining a total of 1600 realizations to explore the relevant parameter space. Propagation of potentially causal pressure changes (ΔP ≥ 0.1 bars) to the mean dVT location (6 km lateral distance, 6 km depth) was favored by channelized fluid flow, high devolatilization rates, and permeabilities similar to those found in geothermal reservoirs (k 10- 16 to 10- 13 m2). For channelized flow, magma-induced thermal pressurization alone can generate cases of Δ P ≥ 0.1 bars for all permeabilities in the range 10- 16 to 10- 13 m2, whereas in radial flow regimes thermal pressurization causes Δ P < 0.1 bars for all permeabilities. Changes in distal fluid pressure occurred before proximal pressure changes given modest anisotropies (kh/kv 10-100). Invoking k(z,T,P) and high, sustained devolatilization rates caused large dynamic fluctuations in k and P in the near-magma environment but had little effect on pressure changes at the distal dVT location. Intrusion below the brittle-ductile transition damps but does not prevent pressure transmission to the dVT site.

VizieR Online Data Catalog: K-H2 line shapes for cool brown dwarfs spectra (Allard+,

NASA Astrophysics Data System (ADS)

Allard, N. F.; Spiegelman, F.; Kielkopf, J. F.

2016-04-01

The relationship between the computed cross section and the normalized absorption coefficient is: I(Δω)=σ(Δω)/π*r0f where r0 is the classical radius of the electron, and f is the oscillator strength of the transition. The far red wing is linearly dependent on H2 density for lower density than 1021cm-3 and can be obtained from the following tables for T=600, 820, 1000, 1500, 2000 and 3000K where n(H2)=1021cm-3. For a more complete profile including the blue wing, opacity tables are available on request from nicole.allard@obspm.fr (2 data files).

Microstructures and Continuous Cooling Transformation of CGHAZ in E36 Class V-N-Ti, V-Ti and Nb-Ti Shipbuilding Steels

NASA Astrophysics Data System (ADS)

Shi, Zhongran; Wang, Ruizhen; Wang, Qingfeng; Su, Hang; Chai, Feng; Yang, Caifu

For the purpose of obtaining the optimal microstructures and mechanical properties of the CGHAZ under high input welding, continuous cooling transformation diagrams of the coarse grain heat-affected zone (CGHAZ) and the corresponding microstructures were investigated for a E36 class V-N-Ti, V-Ti, and Nb-Ti shipbuilding steels. The results indicated that the CGHAZ continuous transformation behaviors of Nb-Ti and V-Ti steel were similar, but the V-retard phenomenon was not as apparent as that of Nb. In addition, the cooling rate of ferrite transformation of V-Ti steel was higher than that of Nb-Ti steel. The nitrogen addition in the V-Ti steel enhanced the ferrite transformation, since that increasing the nitrogen could obtain fine (Ti, V)(C, N) particles and refine the original austenite size, which can promote the ferrite nucleation. The bainite transformation range of V-N-Ti steel was obviously lower than that of Nb-Ti, V-Ti steel at the t8/5≥100s.

The 21st Century Marine Expeditionary Unit

DTIC Science & Technology

2012-05-01

SUBTITLE The 21st Century Marine Expeditionary Unit 5a. CONTRACT NUMBER N/ A 5b. GRANT NUMBER N/ A 5c. PROGRAM ELEMENT NUMBER N/ A 6. AUTHOR(S) Steele...Christopher T 5d. PROJECT NUMBER N/ A 5e. TASK NUMBER N/ A 5f. WORK UNIT NUMBER N/ A 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) USMC...Command and Staff College Marine Corps University 2076 South Street Quantico, VA 22134-5068 8. PERFORMING ORGANIZATION REPORT NUMBER N/ A 9

MEMS Lens Scanners for Free-Space Optical Interconnects

DTIC Science & Technology

2011-12-15

22] D. C. O ? Brien , G. E. Faulkner, T. D. Wilkinson, B. Robertson, and D. G. Leyva, “Design and Analysis of an Adaptive Board-to-Board Dynamic...trenches on 20 µm device layer. (c-d) Deposit and pattern low-stress nitride and polysilicon for electrical isolation. (e) DRIE for MEMS structures...Telecentric Lateral Shift Board Translation (mm) D is p la c e m e n t o f S p o t (  m ) 0 0.5 1 1.5 2 0 100 200 300 400 Tilt Error Board Tilt (deg) D

Chromium release from new stainless steel, recycled and nickel-free orthodontic brackets.

PubMed

Sfondrini, Maria Francesca; Cacciafesta, Vittorio; Maffia, Elena; Massironi, Sarah; Scribante, Andrea; Alberti, Giancarla; Biesuz, Raffaela; Klersy, Catherine

2009-03-01

To test the hypothesis that there is no difference in the amounts of chromium released from new stainless steel brackets, recycled stainless steel brackets, and nickel-free (Ni-free) orthodontic brackets. This in vitro study was performed using a classic batch procedure by immersion of the samples in artificial saliva at various acidities (pH 4.2, 6.5, and 7.6) over an extended time interval (t(1) = 0.25 h, t(2) = 1 h, t(3) = 24 h, t(4) = 48 h, t(5) = 120 h). The amount of chromium release was determined using an atomic absorption spectrophotometer and an inductively coupled plasma atomic emission spectrometer. Statistical analysis included a linear regression model for repeated measures, with calculation of Huber-White robust standard errors to account for intrabracket correlation of data. For post hoc comparisons the Bonferroni correction was applied. The greatest amount of chromium was released from new stainless steel brackets (0.52 +/- 1.083 microg/g), whereas the recycled brackets released 0.27 +/- 0.38 microg/g. The smallest release was measured with Ni-free brackets (0.21 +/- 0.51 microg/g). The difference between recycled brackets and Ni-free brackets was not statistically significant (P = .13). For all brackets, the greatest release (P = .000) was measured at pH 4.2, and a significant increase was reported between all time intervals (P < .002). The hypothesis is rejected, but the amount of chromium released in all test solutions was well below the daily dietary intake level.

Differential Equations, Related Problems of Pade Approximations and Computer Applications

DTIC Science & Technology

1988-12-31

Building 410 1z C ’. O, 4- ~ ~ t ~ Boiling, APE DC 20332-6448 k &L jY naIc l iV n~a -(2)7 _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 8a. NAME OF FUNDING / SPONSORING 1b...SECUAITY C SSIFICATION 0 UNCLASSIFIEO/UNLIMITE-D 0 SAME AS RPT. C3 DTIC USERS ((1 ’ ’ 𔃺C 222. NAME OP RESPONSILI INDIVIDUAL 22b. TELEPHONE (include A...0Ŗ- IN A C h M 6 w V21 767- i-= DForm 1473. Je N 6Previou editons are ouch"e PAC 89 5 1 22 5 Grant No. AFOSR-87-0117 - 9 )6 2 Differential

Environmental Impact Statement for BOMARC Missile Site, McGuire AFB, New Jersey. Volume 2. Public Hearings, Comments, and Consultation Letters. Appendices 2-1 through 2-6

DTIC Science & Technology

1992-05-22

mwwOr kh" I amb m . i COh NO oO*Mm WII Mdhssosm t eu Sm MONLd ispom. "INOW N awo o d td ,1 0 e sk owasomm do ya Cmis Me ThmtU .111Nw dosd ckwfy W4...9We sb bbD Pf - ue my. ai misyss m k -dm ad IRS vr b 1s man cmm ato blb, Wman sinrn as m Air Fam. IOW Vow W k" atss adh do asmm wEwie miad go mo a my...rteutes end energy(lea"se) hus " td thse draft g5 su ta l lePuot ttesnt fur thu SUMibsile ine. saftre Alt r#_u le. Ste Jersey. end ma he. 0440e atuu Ce% bo I

Investigation of Creep Processes and Microdamages in 10Kh9V2MFBR-Sh High-Chromium Steel

NASA Astrophysics Data System (ADS)

Grin', E. A.; Pchelintsev, A. V.

2018-01-01

During the modernization and the new construction of power units at TPPs in Russia, high-chromium martensitic steels with higher heat-resistant properties than the traditional perlite steels are increasingly used as structural materials. High-chromium steels have a necessary regulatory support for their use in domestic power engineering. However, up to the present time, the issue of assessing the quality of these steels at the analysis of their state during long-term operation remains open. The article proposed is one of the first attempts to create a system of quality criteria for martensitic steels based on their microdamage parameters. Tests were carried out on the long-term strength and creep of samples from 10Kh9V2MFBR-Sh steel at high temperatures with the construction of creep curves in relative coordinates "deformation related to the deformation of fracture, current time related to time to failure." For some samples, the tests were interrupted and the metal was subjected to metallographic studies consisting of the analysis of microdamage with reference to the accumulated creep strain. It has been shown experimentally that the deformation curve of high-chromium steel differs from the analogous curve of pearlitic steel by a longer and flat section of steady creep and by a sharper transition to the third accelerated creep stage, which has a very short time period (approximately 10% of the total durability). The tendency to the increase in the microdamage of the structure of steel as the accumulated creep strain increases with time was confirmed. The beginning of transition to the final creep phase is characterized by the formation of contours of future pore chains and by the appearance of individual large pores of up to 6 μm in size, the presence of which in the microstructure of the martensitic steel indicates a very significant accumulation of creep strain, and corresponds to the predestruction stage of metal. It is necessary to continue the research to obtain quantitative indicators on the accumulation of microdamage in high-chromium steel in a conjunction with the development of a metal resource under creep conditions.

Effect of 0.2 and 0.5% Ti on the microstructure and mechanical properties of 13Cr supermartensitic stainless steel

NASA Astrophysics Data System (ADS)

Lian, Yong; Huang, Jinfeng; Zhang, Jin; Zhang, Cheng; Gao, Wen; Zhao, Chao

2015-11-01

The effect that a 0, 0.2, and 0.5 wt.% titanium content has on the microstructure and mechanical properties of 13Cr supermartensitic stainless steel was investigated using an optical microscope, transmission electron microscope, and X-ray diffraction. The resultant microstructures of the three steels were tempered martensite with a reversed austenite dispersed throughout the matrix. Additionally, the formation of Cr-rich carbides was suppressed by stable Ti(C, N), which improved the strength without severely decreasing in the Ti-microalloyed steel toughness. Nano-precipitation of Ni3Ti was found for the 0.5 wt.% Ti steel during tempering, which significantly increased the strength, but decreased the toughness. The reversed austenite volume fraction also significantly influenced the mechanical properties.

Operable Unit B Remedial Investigation Sampling and Analysis Plan. Installation Restoration Program (IRP) McClellan Air Force Base

DTIC Science & Technology

1991-11-01

R A DIA N.... cCELA AFB CALIFRNI55259......... ... RADIAN C 0 37 54 0 z is T 1 0 10395 Old Placcrvillc Road Sacramcnto, CA 95827 191461362-5 H3 2...SAME AS r __ OTic usERs Undlassified 22a. NAME OF RESPONSIBLE INDIVIDUAL 22b. TELEPHONE oncoude Area Code) 22c. OFFICE SYMBOL Mr. P. Haas 1 -800-821...Page 1.0 INTRODUCTION .................................... . 1 - 1 2.0 SITE DESCRIPTION .................................. 2- 1 2.1 Type of Facilities

Pressure effects in the itinerant antiferromagnetic metal TiAu

DOE PAGES

Wolowiec, C. T.; Fang, Y.; McElroy, C. A.; ...

2017-06-07

Here, we report the pressure dependence of the Néel temperature T N up to P ≈ 27 GPa for the recently discovered itinerant antiferromagnet (IAFM) TiAu. The T N(P) phase boundary exhibits unconventional behavior in which the Néel temperature is enhanced from T N ≈ 33 K at ambient pressure to a maximum of T N ≈ 35 K occurring at P ≈ 5.5 GPa. Upon a further increase in pressure, T N is monotonically suppressed to ~22 K at P ≈ 27 GPa. We also find a crossover in the temperature dependence of the electrical resistivity ρ in themore » antiferromagnetic (AFM) phase that is coincident with the peak in T N(P), such that the temperature dependence of ρ = ρ 0 + A nT n changes from n≈3 during the enhancement of T N to n ≈ 2 during the suppression of T N. Based on an extrapolation of the T N(P) data to a possible pressure-induced quantum critical point, we estimate the critical pressure to be P c ≈ 45 GPa.« less

The effect of APOA5 and APOC3 variants on lipid parameters in European Whites, Indian Asians and Afro-Caribbeans with type 2 diabetes.

PubMed

Dorfmeister, Birgit; Cooper, Jackie A; Stephens, Jeffrey W; Ireland, Helen; Hurel, Steven J; Humphries, Steve E; Talmud, Philippa J

2007-03-01

Common variants in APOA5 and APOC3 have been associated with differences in plasma triglyceride (TG) levels in healthy individuals. The aim of this study was to examine the association of APOA5 (-1131T>C, S19W) and APOC3 (-482C>T, 1100C>T) polymorphisms in patients with type 2 diabetes (T2D) of European White (EW) (n=931), Indian Asian (IA) (n=610) and Afro-Caribbean (AC) (n=167) origin, with lipid and T2D parameters. Rare allele frequencies and linkage disequilibrium differed significantly amongst ethnic groups. Compared to APOA5 -1131T and 19S homozygotes, -1131C and 19W carriers had higher TGs in all groups, but this effect was only statistically significant for the -1131C in the EWs (P=0.04) and 19W in the IAs (P<0.001). APOC3 SNPs showed no significant association with lipid levels in any ethnic group. While haplotypes carrying -1131C allele showed significant TG-raising in the EWs only, the 19W defined haplotype showed significant TG-raising in both IAs and EWs. Comparing all four SNPs in EW T2D subjects with healthy EWs (n=2579), the APOC3 1100C>T frequency was significantly higher in T2D [0.26 (0.24, 0.28)] vs. healthy EWs [0.22 (0.20, 0.23)], P=0.001. While the variable size effects of the two APOA5 SNPs on TG levels may result from ethnically different gene-gene or gene-environment interactions, APOA5 and APOC3 variants did not affect parameters of T2D. However, comparison between EWs with T2D and healthy EWs suggest APOC3 1100C>T is associated with increased risk of diabetes probably through mechanisms other than direct effects on TG.

Taipei IAP, Taiwan. Revised Uniform Summary of Surface Weather Observations (RUSSWO). Parts A-F.

DTIC Science & Technology

1973-09-07

p ILA" .O.. (L.’ SPEED ,t MEAN (KNTS) 14-6 7. 10 1 -16 17- 21 22 -27 28 33 34 40 41 %. WEND DIR. iSP~ tD N ___ _ .1! 3_ _ - N .71 I _2 ._ 1 .- 5. ENE...LL .,. ,L - k -- ... 1 1. 117 L53 561 55 .3 3.2 3.0 151 1.1 .31 13Q 119 120 128 54/ 53. ,. 3.7 2 5 1,4 7_ 12A 137 106 52/ 51 .1 2.2 2.21 .2 ,1 86 86...43 1Z 362 74/ 7l . j~e *b .6 .1 .1 𔃻! 41 97 2101 72/ 71 tL. ,. 13 . .A__._ __.. 16 - L53 88 7./ 69 .2 .1 . 6 23 571 ___o zL -- -- .. A. .. 66/ 65

Low Cycle Fatigue Behavior of 316LN Stainless Steel Alloyed with Varying Nitrogen Content. Part II: Fatigue Life and Fracture Behavior

NASA Astrophysics Data System (ADS)

Prasad Reddy, G. V.; Sandhya, R.; Sankaran, S.; Mathew, M. D.

2014-10-01

Influence of nitrogen content on low cycle fatigue life and fracture behavior of 316LN stainless steel (SS) alloyed with 0.07 to 0.22 wt pct nitrogen is presented in this paper over a range of total strain amplitudes ( ±0.25 to 1.0 pct) in the temperature range from 773 K to 873 K (500 °C to 600 °C). The combined effect of nitrogen and strain amplitude on fatigue life is observed to be complex i.e., fatigue life either decreases/increases with increase in nitrogen content or saturates/peaks at 0.14 wt pct N depending on strain amplitude and temperature. Coffin-Manson plots (CMPs) revealed both single-slope and dual-slope strain-life curves depending on the test temperature and nitrogen content. 316LN SS containing 0.07 and 0.22 wt pct N showed nearly single-slope CMP at all test temperatures, while 316LN SS with 0.11 and 0.14 wt pct N exhibited marked dual-slope behavior at 773 K (500 °C) that changes to single-slope behavior at 873 K (600 °C). The changes in slope of CMP are found to be in good correlation with deformation substructural changes.

Successful Microbubble Sonothrombolysis without Tissue Plasminogen Activator in a Rabbit Model of Acute Ischemic Stroke

PubMed Central

Culp, William C.; Flores, Rene; Brown, Aliza T.; Lowery, John D.; Roberson, Paula K.; Hennings, Leah J.; Woods, Sean D.; Hatton, Jeff H.; Culp, Benjamin C.; Skinner, Robert D.; Borrelli, Michael J.

2011-01-01

Background Microbubbles (MB) combined with ultrasound (US) have been shown to lyse clots without tissue plasminogen activator (tPA) both in vitro and in vivo. We evaluated sonothrombolysis with three types of MB using a rabbit embolic stroke model. Methods New Zealand White rabbits (n=74) received internal carotid angiographic embolization of single 3 day-old cylindrical clots (0.6×4.0-mm). Groups included: 1) control (n=11) embolized without treatment, 2) tPA (n=20), 3) tPA+US (n=10), 4) Perflutren Lipid MB+US (n=16), 5) albumin 3µm MB+US (n=8), and 6) tagged albumin 3µm MB+US (n=9). Treatment began 1 hour post-embolization. Ultrasound was pulsed-wave (1 MHz; 0.8 W/cm2) for 1 hour; rabbits with tPA received intravenous tPA (0.9 mg/kg) over 1 hour. Lipid MB dose was intravenous (0.16 mg/kg) over 30 minutes. Dosage of 3µm MB was 5×109 MB intravenously alone or tagged with eptifibatide and fibrin antibody over 30 minutes. Rabbits were euthanized at 24 hours. Infarct volume was determined using vital stains on brain sections. Hemorrhage was evaluated on H&E sections. Results Infarct volume percent was lower for rabbits treated with Lipid MB+US (1.0%±0.6%; P=0.013), 3µm MB+US (0.7%±0.9%; P=0.018), and tagged 3µm MB+US (0.8%±0.8%; P=0.019) compared with controls (3.5%±0.8%). The three MB types collectively had lower infarct volumes (P=0.0043) than controls. Infarct volume averaged 2.2%±0.6% and 1.7%±0.8% for rabbits treated with tPA alone and tPA+US, respectively (P=NS). Conclusions Sonothrombolysis without tPA using these MB is effective in decreasing infarct volumes. Study of human application and further MB technique development are justified. PMID:21700942

On the Extreme Order Statistics for a Stationary Sequence.

DTIC Science & Technology

1987-07-01

n- n n-a [on] n n-.n ’[on] n 5 ur p[\\(k) su (aT) !£ --<lim P[M kOT) ] n-" O n < n 2 by (2.1) and (2.2), it is easily seen that P[M (k) < u ( r ...8217 ; 0 i< n IS1, - ( r , i7 k-i1 2 k-ii "’’ .- (k) -OTk i ( s) - . Corollary 3.2 P[" [on] < = e [k 1 7 n (i’T)] + o (I)-.’]v =I Z ! i=Z n where 7 (i;T) is...tends to o by (3.3). Thusn r n kn n I (X > 0) converges in distribution to a Poisson variable with mean m=I ~n,m OT, from which the result easily follows

Corrosion behavior of an HVOF-sprayed Fe3Al coating in a high-temperature oxidizing/sulfidizing environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Covino, Bernard S., Jr.; Bullard, Sophie J.; Cramer, Stephen D.

An iron aluminide (Fe3Al) intermetallic coating was deposited onto a F22 (2.25Cr-1Mo) steel substrate using a JP-5000 high velocity oxy-fuel (HVOF) thermal spray system. The as-sprayed coating was examined by electron microscopy and X-ray diffraction and was characterized in terms of oxidation and adhesion. Fe3Al-coated steel specimens were exposed to a mixed oxidizing/sulfidizing environment at 500, 600, 700, and 800DGC for approximately seven days. The gaseous environment consisted of N2-10%CO-5%CO2-2%H2O-0.12%H2S (by volume). All specimens gained mass after exposure to the environment and the mass gains were found to be inversely proportional to temperature increases. Representative specimens exposed at each temperaturemore » were cross-sectioned and subjected to examination under a scanning electron microscope (SEM) and X-ray mapping. Results are presented in terms of corrosion weight gain and corrosion product formation. The purpose of the research presented here was to evaluate the effectiveness of an HVOF-sprayed Fe3Al coating in protecting a steel substrate exposed to a fossil energy environment.« less

Interaction of elongation factor Tu from Escherichia coli with aminoacyl-tRNA carrying a fluorescent reporter group on the 3' terminus.

PubMed

Ott, G; Faulhammer, H G; Sprinzl, M

1989-09-15

Transfer ribonucleic acids containing 2-thiocytidine in position 75 ([s2C]tRNAs) were prepared by incorporation of the corresponding cytidine analogue into 3'-shortened tRNA using ATP(CTP):tRNA nucleotidyltransferase. [s2C]tRNA was selectively alkylated with fluorescent N-iodoacetyl-N'-(5-sulfo-1-naphthyl)ethylenediamine (1,5-I-AEDANS) on the 2-thiocytidine residue. The product [AEDANS-s2C]aminoacyl-tRNA, forms a ternary complex with Escherichia coli elongation factor Tu and GTP, leading to up to 130% fluorescence enhancement of the AEDANS chromophore. From fluorescence titration experiments, equilibrium dissociation constants of 0.24 nM, 0.22 nM and 0.60 nM were determined for yeast [AEDANS-s2C]Tyr-tRNATyr, yeast Tyr-tRNATyr, and the homologous E. coli Phe-tRNAPhe, respectively, interacting with E. coli elongation factor Tu.GTP. The measurement of the association and dissociation rates of the interaction of [AEDANS-s2C]Tyr-tRNATyr with EF-Tu.GTP and the temperature dependence of the resulting dissociation constants gave values of 55 J mol-1 K-1 for delta S degrees' and -34.7 kJ mol-1 for delta H degrees' of this reaction.

Numerical studies of the Kelvin-Hemholtz instability in a coronal jet

NASA Astrophysics Data System (ADS)

Zhao, Tian-Le; Ni, Lei; Lin, Jun; Ziegler, Udo

2018-04-01

Kelvin-Hemholtz (K-H) instability in a coronal EUV jet is studied via 2.5D MHD numerical simulations. The jet results from magnetic reconnection due to the interaction of the newly emerging magnetic field and the pre-existing magnetic field in the corona. Our results show that the Alfvén Mach number along the jet is about 5–14 just before the instability occurs, and it is even higher than 14 at some local areas. During the K-H instability process, several vortex-like plasma blobs with high temperature and high density appear along the jet, and magnetic fields have also been rolled up and the magnetic configuration including anti-parallel magnetic fields forms, which leads to magnetic reconnection at many X-points and current sheet fragments inside the vortex-like blob. After magnetic islands appear inside the main current sheet, the total kinetic energy of the reconnection outflows decreases, and cannot support the formation of the vortex-like blob along the jet any longer, then the K-H instability eventually disappears. We also present the results about how the guide field and flux emerging speed affect the K-H instability. We find that a strong guide field inhibits shock formation in the reconnecting upward outflow regions but helps secondary magnetic islands appear earlier in the main current sheet, and then apparently suppresses the K-H instability. As the speed of the emerging magnetic field decreases, the K-H instability appears later, the highest temperature inside the vortex blob gets lower and the vortex structure gets smaller.

Pakistan’s Nuclear Future: Worries Beyond War

DTIC Science & Technology

2008-01-01

sources such as cobalt irradiation sources , neutron sources , etc. that could be utilized by experienced...Kh an AQ K ha n o ffe r t o I ra q Pr es sle r s an cti on s ( Oc t.) 19 91 Gh ula m Ish aq K ha n Na wa z S ha rif Mi rza A sla m Be g ( Ja nu...or th Ko re a ( De c.) 19 94 Fa ro oq Le gh ar i Be na zir B hu tto Ab du l W ah id Ka ka r Se

Development of CMOS MEMS inductive type tactile sensor with the integration of chrome steel ball force interface

NASA Astrophysics Data System (ADS)

Yeh, Sheng-Kai; Chang, Heng-Chung; Fang, Weileun

2018-04-01

This study presents an inductive tactile sensor with a chrome steel ball sensing interface based on the commercially available standard complementary metal-oxide-semiconductor (CMOS) process (the TSMC 0.18 µm 1P6M CMOS process). The tactile senor has a deformable polymer layer as the spring of the device and no fragile suspended thin film structures are required. As a tactile force is applied on the chrome steel ball, the polymer would deform. The distance between the chrome steel ball and the sensing coil would changed. Thus, the tactile force can be detected by the inductance change of the sensing coil. In short, the chrome steel ball acts as a tactile bump as well as the sensing interface. Experimental results show that the proposed inductive tactile sensor has a sensing range of 0-1.4 N with a sensitivity of 9.22(%/N) and nonlinearity of 2%. Preliminary wireless sensing test is also demonstrated. Moreover, the influence of the process and material issues on the sensor performances have also been investigated.

Comparison of spring characteristics of titanium-molybdenum alloy and stainless steel

PubMed Central

Salehi, Anahita; Asatourian, Armen

2017-01-01

Background Titanium-molybdenum alloy (TMA) and stainless steel (SS) wires are commonly used in orthodontics as arch-wires for tooth movement. However, plastic deformation phenomenon in these arch-wires seems to be a major concern among orthodontists. This study aimed to compare the mechanical properties of TMA and SS wires with different dimensions. Material and Methods Seventy-two wire samples (36 TMA and 36 SS) of three different sizes (19×25, 17×25 and 16×22) were analyzed in vitro, with 12 samples in each group. Various mechanical properties of the wires, including spring-back, bending moment and stiffness were determined using a universal testing machine. Student’s t-test showed statistically significant differences in the mean values of all the groups. In addition, metallographic comparison of SS and TMA wires was conducted under an optical microscope. Results The degree of stiffness of 16×22-sized SS and TMA springs was found to be 12±2 and 5±0.4, respectively, while the bending moment was estimated to be 1927±352 (gm-mm) and 932±16 (gm-mm), respectively; the spring-back index was determined to be 0.61±0.2 and 0.4±.09, respectively (p<0.001). There were no statistically significant differences in spring-back index in larger dimensions of the wires. Conclusions Systematic analysis indicated that springs made of TMA were superior compared to those made of SS. Although both from economic and functionality viewpoints the use of TMA is suggested, further clinical investigations are recommended. Key words:Bending moment, optical microscope, spring-back, stainless steel, stiffness, titanium‒molybdenum alloy. PMID:28149469

Investigation of the structure and properties of titanium-stainless steel permanent joints obtained by laser welding with the use of intermediate inserts and nanopowders

NASA Astrophysics Data System (ADS)

Cherepanov, A. N.; Orishich, A. M.; Pugacheva, N. B.; Shapeev, V. P.

2015-03-01

Results of an experimental study of the structure, the phase composition, and the mechanical properties of laser-welded joints of 3-mm thick titanium and 12Kh18N10T steel sheets obtained with the use of intermediate inserts and nanopowdered modifying additives are reported. It is shown that that such parameters as the speed of welding, the radiation power, and the laser-beam focal spot position all exert a substantial influence on the welding-bath process and on the seam structure formed. In terms of chemical composition, most uniform seams with the best mechanical strength are formed at a 1-m/min traverse speed of laser and 2.35-kW laser power, with the focus having been positioned at the lower surface of the sheets. Under all other conditions being identical, uplift of the focus to workpiece surface or to a higher position results in unsteady steel melting, in a decreased depth and reduced degree of the diffusion-induced mixing of elements, and in an interpolate connection formed according to the soldering mechanism in the root portion of the seam. The seam material is an over-saturated copper-based solid solution of alloying elements with homogeneously distributed intermetallic disperse particles (Ti(Fe, Cr)2 and TiCu3) contained in this alloy. Brittle fracture areas exhibiting cleavage and quasi-cleavage facets correspond to coarse Ti(Fe, Cr)2 intermetallic particles or to diffusion zones primarily occurring at the interface with the titanium alloy. The reported data and the conclusions drawn from the numerical calculations of the thermophysical processes of welding of 3-mm thick titanium and steel sheets through an intermediate copper insert are in qualitative agreement with the experimental data. The latter agreement points to adequacy of the numerical description of the melting processes of contacting materials versus welding conditions and focal-spot position in the system.

Exposure to air pollution near a steel plant and effects on cardiovascular physiology: a randomized crossover study.

PubMed

Liu, Ling; Kauri, Lisa Marie; Mahmud, Mamun; Weichenthal, Scott; Cakmak, Sabit; Shutt, Robin; You, Hongyu; Thomson, Errol; Vincent, Renaud; Kumarathasan, Premkumari; Broad, Gayle; Dales, Robert

2014-03-01

Iron and steel industry is an important source of air pollution emissions. Few studies have investigated cardiovascular effects of air pollutants emitted from steel plants. We examined the influence of outdoor air pollution in the vicinity of a steel plant on cardiovascular physiology in Sault Ste. Marie, Canada. Sixty-one healthy, non-smoking subjects (females/males=33/28, median age 22 years) spent 5 consecutive 8-hour days outdoors in a residential area neighbouring a steel plant, or on a college campus approximately 5 kilometres away from the plant, and then crossed over to the other site with a 9-day washout. Mid day, subjects underwent daily 30-minute moderate intensity exercise. Blood pressure (BP) and pulse rate were determined daily and post exercise at both sites. Flow-mediated vasodilation (FMD) was determined at the site near the plant. Air pollution was monitored at both sites. Mixed-effects regressions were run for statistical associations, adjusting for weather variables. Concentrations of ultrafine particles, sulphur dioxide (SO2), nitrogen dioxide (NO2) and carbon monoxide (CO) were 50-100% higher at the site near the plant than at the college site, with minor differences in temperature, humidity, and concentrations of particulate matter ≤2.5 μm in size (PM2.5) and ozone (O3). Resting pulse rate [mean (95% confidence interval)] was moderately higher near the steel plant [+1.53 bpm (0.31, 2.78)] than at the college site, male subjects having the highest pulse rate elevation [+2.77 bpm (0.78, 4.76)]. Resting systolic and diastolic BP and pulse pressure, and post-exercise BP and pulse rate were not significantly different between two sites. Interquartile range concentrations of SO2 (2.9 ppb), NO2 (5.0 ppb) and CO (0.2 ppm) were associated with increased pulse rate [0.19 bpm (-0.00, 0.38), 0.86 bpm (0.03, 1.68), and 0.11 bpm (0.00, 0.22), respectively], ultrafine particles (10,256 count/cm(3)) associated with increased pulse pressure [0.85 mmHg (0.23, 1.48)], and NO2 and CO inversely associated with FMD [-0.14% (-0.31, 0.02), -0.02% (-0.03, -0.00), respectively]. SO2 during exercise was associated with increased pulse rate [0.26 bpm (0.01, 0.51)]. Air quality in residential areas near steel plants may influence cardiovascular physiology. Copyright © 2013 Elsevier GmbH. All rights reserved.

Evaluating Henry's law constant of N-nitrosodimethylamine (NDMA).

PubMed

Haruta, Shinsuke; Jiao, Wentao; Chen, Weiping; Chang, Andrew C; Gan, Jay

2011-01-01

N-Nitrosodimethylamine (NDMA), a potential carcinogen, may contaminate the groundwater when the reclaimed wastewater is used for irrigation and groundwater recharge. Henry's law constant is a critical parameter to assess the fate and transport of reclaimed wastewater-borne NDMA in the soil profile. We conducted a laboratory experiment in which the change of NDMA concentration in water exposed to the atmosphere was measured with respect to time and, based on the data, obtained the dimensionless Henry's law constant (K(H)') of NDMA, at 1.0 x 10(-4). The K(H)' suggests that NDMA has a relatively high potential to volatilize in the field where NDMA-containing wastewater is used for irrigation and the volatilization loss may be a significant pathway of NDMA transport. The experiment was based on the two boundary-layer approach of mass transfer at the atmosphere-water interface. It is an expedient method to delineate K(H)' for volatile or semi-volatile compounds present in water at low concentrations.

Ultra-High-Modulus Graphite-Epoxy Conical Shell Development. Supplement

DTIC Science & Technology

1979-04-01

934 (0/±45/90)8 t = o.040 T - 300/934 MS124815 CRES HELICOIL O. 190-32 TiffiEAD, 3 DIA · NOM. LG. Install per MS33537 Oirnensions are inches...1613 psi avg 325F critu 1384 psi avg 3 -29 0.5 i ’ I 2.0 DIA • .. - -..-.! 0.75 DIA . + LOAD t LOAD THREAD Dimensions are inches. STEEL...THiCK T-300/934 (Ol!. 45/90Jsc T-300/934 [ 0/:!::. 45/90]5 t := 0.040 MS124815 CRES HEUCOIL I I I I ’ ’ I I ~ ;, 0 . 190-32 WREAD, 3 DIA

Dissimilar Impact Welding of 6111-T4, 5052-H32 Aluminum Alloys to 22MnB5, DP980 Steels and the Structure-Property Relationship of a Strongly Bonded Interface

NASA Astrophysics Data System (ADS)

Liu, Bert; Vivek, Anupam; Presley, Michael; Daehn, Glenn S.

2018-03-01

The ability to weld high-strength aluminum to high-strength steel is highly desired for vehicle lightweighting but difficult to attain by conventional means. In this work, vaporizing foil actuator welding was used to successfully weld four Al/Fe combinations consisting of high-strength alloys: AA5052-H32, AA6111-T4, DP980, and 22MnB5. Flyer velocities up to 727 m/s were reached using 10 kJ input energy. In lap-shear testing, samples primarily failed in base aluminum near the aluminum's native strength, showing that the welds were stronger than a base metal and that the base metal was not significantly weakened by the welding process. A particularly strong weld area was studied by transmission electron microscopy to shed light on the microstructural features of strong impact welds. It was found to be characterized by a continuously bonded, fully crystalline interface, extremely fine (nanoscale) grains, mesoscopic as well as microscopic wavy features, and lack of large continuous intermetallic compounds.

Prime Contract Awards Alphabetically by Contractor, by State or Country, and Place, Fiscal Year 1987. Part 2. American Steel & Wldg. Company-Becker Sand & Gravel Company, Incorporated.

DTIC Science & Technology

1987-01-01

m 0 mOC uO 0 NO 0) u0 co C..N EN N O NN -4-a) 0)L 4 0.) MOOC en 0 Z CO 00Z CL 0 QI 0 Oo 000 0O (UA -4A m 1 000 00 00 00 00 0 0 CID 0 C o C C00 00 00...N t- 0: 02 ClO ’ 02 0’ r) 4)C (clC𔃺tA.0-I (04-.J 00 00-Ala-CDom~ 𔃺 C ) ) 0) cn 04 ON) ZN ZOII’’OI 0 30-4 (D M 0 mooC ~l-AO-NO N0-0.-0(0 0 0 ON. 4I...D 00m aA C3’) (N * 0N 020 0 0 4 0 En Caw 001 0 0 00 0 00 0 >-)l󈧄I’ ’a 0൓ mooc - 0 * n cw ztcIt -o 0. . . (a m1 -t10OOD Oi t )U)c 1 0z -0- Tz 0m = M

Salibacter halophilus gen. nov., sp. nov., isolated from a saltern

USDA-ARS?s Scientific Manuscript database

A Gram-stain-negative and facultatively anaerobic bacterium, JZ3C34**T, was isolated from a saltern near Feicheng, China (36°8'24.45" E, 116°49'22.46" N). Cells of strain JZ3C34**T were 0.3-0.4µm wide and 1.5-2.0µm long, catalase-positive and oxidase-negative. Colonies were transparent, orange and a...

In-vitro Assessment of Knee MRI in the Presence of Metal Implants Comparing MAVRIC-SL and Conventional FSE Sequences at 1.5 and 3 Tesla Field Strength

PubMed Central

Liebl, Hans; Heilmeier, Ursula; Lee, Sonia; Nardo, Lorenzo; Patsch, Janina; Schuppert, Christopher; Han, Misung; Rondak, Ina-Christine; Banerjee, Suchandrima; Koch, Kevin; Link, Thomas M.; Krug, Roland

2014-01-01

PURPOSE To assess lesion detection and artifact size reduction of a MAVRIC-SEMAC hybrid sequence (MAVRIC-SL) compared to standard sequences at 1.5T and 3T in porcine knee specimens with metal hardware. METHODS Artificial cartilage and bone lesions of defined size were created in the proximity of titanium and steel screws with 2.5 mm diameter in 12 porcine knee specimens and were imaged at 1.5T and 3T MRI with MAVRIC-SL PD and STIR, standard FSE T2 PD and STIR and fat-saturated T2 FSE sequences. Three radiologists blinded to the lesion locations assessed lesion detection rates on randomized images for each sequence using ROC. Artifact length and width were measured. RESULTS Metal artifact sizes were largest in the presence of steel screws at 3T (FSE T2 FS: 28.7cm2) and 1.5T (16.03cm2). MAVRIC-SL PD and STIR reduced artifact sizes at both 3T (1.43cm2; 2.46cm2) and 1.5T (1.16cm2; 1.59cm2) compared to FS T2 FSE sequences (27.57cm2; 13.20cm2). At 3T, ROC derived AUC values using MAVRIC-SL sequences were significantly higher compared to standard sequences (MAVRIC-PD: 0.87, versus FSE-T2-FS: 0.73 (p=0.025); MAVRIC- STIR: 0.9 versus T2-STIR: 0.78 (p=0.001) and versus FSE-T2-FS: 0.73 (p=0.026)). Similar values were observed at 1.5T. Comparison of 3T and 1.5T showed no significant differences (MAVRIC-SL PD: p=0.382; MAVRIC-SL STIR: p=0.071. CONCLUSION MAVRIC-SL sequences provided superior lesion detection and reduced metal artifact size at both 1.5T and 3T compared to conventionally used FSE sequences. No significant disadvantage was found comparing MAVRIC-SL at 3T and 1.5T, though metal artifacts at 3T were larger. PMID:24912802

Hot water-extracted Lycium barbarum and Rehmannia glutinosa inhibit proliferation and induce apoptosis of hepatocellular carcinoma cells

PubMed Central

Chao, Jane C-J; Chiang, Shih-Wen; Wang, Ching-Chiung; Tsai, Ya-Hui; Wu, Ming-Shun

2006-01-01

AIM: To investigate the effect of hot water-extracted Lycium barbarum (LBE) and Rehmannia glutinosa (RGE) on cell proliferation and apoptosis in rat and/or human hepatocellular carcinoma (HCC) cells. METHODS: Rat (H-4-II-E) and human HCC (HA22T/VGH) cell lines were incubated with various concentrations (0-10 g/L) of hot water-extracted LBE and RGE. After 6-24 h incubation, cell proliferation (n = 6) was measured by a colorimetric method. The apoptotic cells (n = 6) were detected by flow cytometry. The expression of p53 protein (n = 3) was determined by SDS-PAGE and Western blotting. RESULTS: Crude LBE (2-5 g/L) and RGE (2-10 g/L) dose-dependently inhibited proliferation of H-4-II-E cells by 11% (P < 0.05) to 85% (P < 0.01) after 6-24 h treatment. Crude LBE at a dose of 5 g/L suppressed cell proliferation of H-4-II-E cells more effectively than crude RGE after 6-24 h incubation (P < 0.01). Crude LBE (2-10 g/L) and RGE (2-5 g/L) also dose-dependently inhibited proliferation of HA22T/VGH cells by 14%-43% (P < 0.01) after 24 h. Crude LBE at a dose of 10 g/L inhibited the proliferation of HA22T/VGH cells more effectively than crude RGE (56.8% ± 1.6% vs 70.3% ± 3.1% of control, P = 0.0003 < 0.01). The apoptotic cells significantly increased in H-4-II-E cells after 24 h treatment with higher doses of crude LBE (2-5 g/L) and RGE (5-10 g/L) (P < 0.01). The expression of p53 protein in H-4-II-E cells was 119% and 143% of the control group compared with the LBE-treated (2, 5 g/L) groups, and 110% and 132% of the control group compared with the RGE -treated (5, 10 g/L) groups after 24 h. CONCLUSION: Hot water-extracted crude LBE (2-5 g/L) and RGE (5-10 g/L) inhibit proliferation and stimulate p53-mediated apoptosis in HCC cells. PMID:16874858

Enhancement and Bandwidth Compression of Noisy Speech by Estimation of Speech and Its Model Parameters

DTIC Science & Technology

1978-08-01

110 V.4.1 Motivation for the Revision 110 V.4.2 Estimation of s(i)’s(j) by E[s(i) s(j) la ,v 111 V.4.3 RLMAP Estimation Procedure 114 V.5 Extension to...and .ne distinction will be left to the context in which it is used. -83- P(Sola,g,si) = p~s(N-1,0) la ,g,s(-!,-p)) N-i = i p (s (n) Ia,g, s(n-1, -p...s(n) la ,g,s(n-!,n-p)) - 1 (si) T 2 2 exp[- -I- (s(n)-a *s(n-1,n-p)) (4-5) (2"rg /2g From equations (4-4) and (4-5), a 1 NI T 2 (Ig ) 22 N/Iexp

Development of a FDA-Approved Pharmaceutical to Treat Noise-Induced Hearing Loss

DTIC Science & Technology

2014-08-13

be reduced by 40 dB, resulting in a 115 dB SPL of noise exposure for personnel servicing the flight operations. (5) BODY: Scientific and Technical...80 . 70 . Zklh ! 60 i - 41oHz 81611 16KH.I i 50 ·-·-----~~---- ! 40 l i JO • 1 zo ------------ 10 0 Z IoHz 41oHz 81oHz 16KHz...15•0/0I ~ 40 \\-- •• -----~r-----/----- -n-151131!0/JOOJ ! JO : 1 zo ’------~~--------- 10 0 1 IoHz 41oHz 8IoHz 16KHz 2 Main Effect: • • • -+-(S.0

Effect of microstructure on transformation-induced plasticity of silicon-containing low-alloy steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tomita, Yoshiyuki; Morioka, Kojiro

1997-04-01

Fe-0.6C-1.5Si-0.8Mn steel was studied to determine the effect of the microstructure on transformation-induced plasticity (TRIP) of silicon-containing low-alloy steel. A remarkable increase in elongation through TRIP can develop in the steel subjected to the following heat treatments: (1) austemper combined with subcritical annealing (SA Aus-T): subcritical annealing at 993K followed by austempering at 673K and then light tempering (after austenitization at 1173K); (2) austemper coupled with interrupted quenching (IQ Aus-T): interrupted quenching at 533K followed by austempering at 673K and light tempering (after austenization at 1,173K). The SA Aus-T treatment produced the triple structures of carbide-free upper bainite, retained austenitemore » ({gamma}R), and free ferrite. As a result of the IQ Aus-T treatment, the triple structures of carbide-free upper bainite, {gamma}R, and tempered martensite appeared. The results are described and microstructural factors in TRIP are discussed.« less

The effect of temperature on post-feeding ammonia excretion and oxygen consumption in the southern catfish.

PubMed

Luo, Yiping; Xie, Xiaojun

2009-08-01

The post-prandial rates of ammonia excretion (TAN) and oxygen consumption MO2 in the southern catfish (Silurus meridionalis) were assessed at 2 h intervals post-feeding until the rates returned to those of the fasting rates, at 17.5, 22.5, 27.5, and 32.5 degrees C, respectively. Both fasting TAN and MO2 increased with temperature, and were lower than those previously reported for many fish species. The relationship between fasting TAN (mmol NH(3)-N kg(-1) h(-1)) and temperature (T, degrees C) was described as: fasting TAN = 0.144e (0.0266T) (r = 0.526, n = 27, P < 0.05). The magnitude of ammonia excretion and its ratio to total N intake EXNH3-N during the specific dynamic action (SDA) tended to increase initially, and then decrease with increasing temperature. The ammonia quotient (AQ), calculated as mol NH(3)-N/mol O(2), following feeding decreased as temperature increased. The relationship between AQ during SDA and temperature was described as: AQ(during SDA) = 0.303e (-0.0143T) (r = 0.739, n = 21, P < 0.05). Our results suggest that ammonia excretion and oxygen consumption post-feeding are operating independently of each other. Furthermore, it appears that the importance of protein as a metabolic substrate in postprandial fish decreases with temperature.

Linear Modulation Techniques for Digital Microwave

DTIC Science & Technology

1979-08-01

impulse response. Following Forney, a polynomial R(D) is defined such that +0o R(D) - Rh (iT)0i (2-2) i00 The coefficients of R(D) are symnetrical...EQUALIZATION: 8/ I - NYQUIST EQUALIZED / 5- -- DUOINARY EQUALIZED NOTE: 6 MODIFIED 6-QAM I- 4 / 4 -2 2 0 5 10 15 20 25 30 35 40 PEAK AMPLIFIER Eb/N0 Ift 103M

Modular Matrix Multiplication on a Linear Array.

DTIC Science & Technology

1983-11-01

is fl(n2). 2 Case e Irl __ (see Figure 5.2) 2 2 ,1 Y, " X2v- ’ Y2 -. x= -- ~ Y4 "i; Yin Figure 5Ŗ At t--xi, either all Gk, such that IkEA , have n...nat and Image Proceuing, IEEE Transactions on Computers, Vol. C-31, No. 10 22 (October, 1982), pp. IO0oo09. [41 H.T. Kung, Let’s Design Algorithms for...VLSI Systems, Proc. Caltech Conf. on Very Large Scale Integration: Architecture, Design , Fabrication (January, 1979), pp. 65. 90. 151 H.T. Kung, and

Anthropometry of Women of the U.S. Army - 1977. Report No. 5 - Comparative Data for U.S. Army Men

DTIC Science & Technology

1977-07-01

75-109.75 18 147 6.27 51922 74.75- 75#70 26 162 9e06 5299b 10?7S-1d8.75 22 129 7.67 44.95 73.75- 74*7:P 2? 126 3.41 43.90 1ab *?$-t~f.75 18 107 6.27...00 P4, " d L5 a .4. eI- uid 0 * (A C3 (4 %a t 4 W4* N 4 4M v4 N 4 1 -4 𔃺 Z O Nr. N I.- udA V- 4 . 02 Lz V5 aA N.4 4 N N f M A V4 Ps (A :." Id -AAi

Use of an Aerodynamic Turn to Maximize the Orbit Inclination Change for the Space Shuttle Orbiter.

DTIC Science & Technology

1979-12-01

0 9 3 p s B A N K A, . 01 . 2 0 d e g ALT MiS -3.57 -0.21 -22.91 m 15. VEL T .009 .005 .00 k s Ai .15 .17 .22 deg ALT ISS -5.66 -12.66 -26.04...ALT MISS 32 7 29. 1 22.5 km 0 VEL MISS -.01. 16 -.018 ,S 0. 0. 0. ALT mISS 31.9 9m 50 VEL MISS -.010 - .016 -. 018 "ps .03 .04 .0- eg ANGLE ALT MISS...31.4 9.1 2_.9 km OF 10 VEL MISS -. 0101 kps Ao .06 .07 .09 dec AL MISS 31.6 27.1 19.5 15 ° VEL MISS -. 010 -. 015 -. 017 kps ,\\i .08 .11 .13 deg ALT

Influence of Zoledronic Acid on Atrial Electrophysiological Parameters and Electrocardiographic Measurements.

PubMed

Tisdale, James E; Allen, Matthew R; Overholser, Brian R; Jaynes, Heather A; Kovacs, Richard J

2015-06-01

Our objective was to determine effects of zoledronic acid (ZA) on atrial electrophysiological parameters and electrocardiographic measurements. Ex vivo perfusion study: Isolated guinea pig hearts were perfused with modified Krebs-Henseleit (K-H) buffer with or without ZA 0.07 mg/kg/L (each n = 6). In ZA-perfused hearts, atrial action potential at 90% repolarization (APD90 ) decreased more from baseline than in controls (-23.2% ± -5.1% vs. -2.1% ± -8.1%, P < 0 .0001), as did APD30 (-28.8% ± -3.8% vs. -2.1% ± -2.1%, P < 0.0001). In vivo dose-response study: Guinea pigs underwent intraperitoneal injections every 2 weeks in 1 of 4 groups (each n = 8): ZA 0.007 mg/kg (low-dose), ZA 0.07 mg/kg (medium-dose), ZA 0.7 mg/kg (high-dose), or placebo. Hearts were excised at 8 weeks and perfused with modified K-H. Atrial effective refractory period (ERP) was lower with medium- and high-dose ZA versus placebo (P = 0.004). Atrial APD30 was lower with high-dose ZA versus placebo, low and medium doses (P < 0.001). Canine ECG study: Mature female beagles received intravenous ZA 0.067 mg/kg or saline (placebo; each n = 6) every 2 weeks for 12 weeks. P wave dispersion was greater in the ZA group (7.7 ± 3.7 vs. 3.4 ± 2.6 ms, P = 0.04). There were no significant differences in P wave index, maximum or minimum P wave duration, or PR interval. ZA shortens left atrial APD and ERP and increases P wave dispersion. © 2015 Wiley Periodicals, Inc.

ACES. Accelerated Corrosion Expert Simulator

DTIC Science & Technology

2010-02-01

Composites Coating Systems Organic Inorganic Ceramic Materials 22 Inputs and Dimensions Xi Thickness Hardness Strength Ductility Abrasion Resistance...GPU 25 T-Handle Latch 10-Year ACT Material/ Coating Configuration Die Cast Zinc T-Handle Carbon Steel Pin CS Shank CS T-Washer Carbon Steel Dish E- coat ...CARC Zinc Plating Cadmium Plated BoltE- coat /CARC CS Panel CS Panel O-Ring E- coat /CARC Original (10-year ACT) Design Green Flag Color Qualitative

Stochastic Euler Equations of Fluid Dynamics with Lvy Noise

DTIC Science & Technology

2016-08-10

Rε ( 1 + E [ sup 0tT∧τN ∥∥uR(t)∥∥2Hs])+ LTE [ sup 0tT∧τN ∥∥uR(t)− u(t)∥∥2Hs′] → 0, as R → ∞, since uR ∈ L2(;L2(0, T ∧ τN ;Hs(Rn))) for any s > n/2...2Hs])+ LTE [ sup 0tT∧τN ∥∥uR(t)− u(t)∥∥2Hs′] → 0, as R → ∞, M.T. Mohan and S.S. Sritharan / Stochastic Euler equations 101 since uR ∈ L2(;L2(0, T

Alpha List of Prime Contract Awards. Oct 91 - Sep 92. FY 92. (Malloy Corporation - Milk Maid Inc)

DTIC Science & Technology

1993-01-01

3 ~LL) CL- a -4 0 00 00 0 0 00 0 0 000 0000 Is 0-4-4 It *N O-40 a tZ on. Oo0) ft Z 2 22 22222*222222 22 22222 a nowo ’ a ca CID mm0)mm0m0mm)002 mm t...4 ONI ON N--’ ’ItN CON 00 00 00000 NO NOC- 34 0 -4 44 3-0 -7 43-3- (Mr Im0 )0 W00 w400 44 -4 0) 347 on a0 1 0-4 300 CV 00a 044 04 (4 0 n(44CI 00.1 -o... NOWO 󈧬ý ’-.IC) :bt L CD0 L-0 L go0 0) N WOO o00 N A0% N -4 -44 ýt .4-4 -4 0 Ln 4N -4,0 L..4 0GO0 C ON X0 N1 N 00 k00 = .C( 0 N L- (n0L L. 0U) -0

Fatty acid composition and oxidative stability of breast meat from broiler chickens supplemented with Moringa oleifera leaf meal over a period of refrigeration.

PubMed

Nkukwana, T T; Muchenje, V; Masika, P J; Hoffman, L C; Dzama, K; Descalzo, A M

2014-01-01

Effects of diets supplemented with or without Moringa oleifera leaf meal (MOLM) on fatty acid (FA) composition and oxidative stability of broiler breast meat during refrigerated storage was determined. Dietary treatments (T) were as follows: T1, positive control, 668g/ton Salinomycin and 500g/ton Albac; T2, T3 and T4 contained graded levels of MOLM at 1%, 3% and 5% of dry matter (DM) intake, respectively; and T5, a negative control (0% additives). Oxidative stability was evaluated by thiobarbituric acid reactive substances (TBARS) on day (D) 1-8 of storage at 4°C; and FA analysis was done on samples obtained on D1 and D8. Significant effects on TBARS were noted on day (D) 1, 3, 4 and 7; increased with increasing storage time, and with increase in MOLM supplementation. Highest (P<0.05) C18:0 and C15:0 levels were noted on D1 in T2; C20:0 in T4 on D8; C20:2, C20:3n6 and C22:6n3 in T2; C18:3n6 and P/S ratio in T4 on D1; and n-3 in T3. Thus, despite the high SFA content, additive supplementation of M. oleifera leaf meal up to 5% of the bird's DMI improved the FA profile and reduced lipid oxidation in broiler breast meat. Copyright © 2013 Elsevier Ltd. All rights reserved.

Chemomechanical preparation by hand instrumentation and by Mtwo engine-driven rotary files, an ex vivo study.

PubMed

Krajczár, Károly; Tigyi, Zoltán; Papp, Viktória; Marada, Gyula; Sára, Jeges; Tóth, Vilmos

2012-07-01

To compare the disinfecting efficacy of the sodium hypochlorite irrigation by root canal preparation with stainless steel hand files, taper 0.02 and nickel-titanium Mtwo files with taper 0.04-0.06. 40 extracted human teeth were sterilized, and then inoculated with Enterococcus faecalis (ATCC 29212). After 6 day incubation time the root canals were prepared by hand with K-files (n=20) and by engine-driven Mtwo files (VDW, Munich, Germany) (n=20). Irrigation was carried out with 2.5% NaOCl in both cases. Samples were taken and determined in colony forming units (CFU) from the root canals before and after the preparation with instruments #25 and #35. Significant reduction in bacterial count was determined after filing at both groups. The number of bacteria kept on decreasing with the extension of apical preparation diameter. There was no significant difference between the preparation sizes in the bacterial counts after hand or engine-driven instrumentation at the same apical size. Statistical analysis was carried out with Mann-Whitney test, paired t-test and independent sample t-test. Significant reduction in CFU was achieved after the root canal preparation completed with 2.5% NaOCl irrigation, both with stainless steel hand or nickel-titanium rotary files. The root canal remained slightly infected after chemo mechanical preparation in both groups. Key words:Chemomechanical preparation, root canal disinfection, nickel-titanium, conicity, greater taper, apical size.

Chemomechanical preparation by hand instrumentation and by Mtwo engine-driven rotary files, an ex vivo study

PubMed Central

Krajczár, Károly; Tigyi, Zoltán; Papp, Viktória; Sára, Jeges; Tóth, Vilmos

2012-01-01

Objective: To compare the disinfecting efficacy of the sodium hypochlorite irrigation by root canal preparation with stainless steel hand files, taper 0.02 and nickel-titanium Mtwo files with taper 0.04-0.06. Study Design: 40 extracted human teeth were sterilized, and then inoculated with Enterococcus faecalis (ATCC 29212). After 6 day incubation time the root canals were prepared by hand with K-files (n=20) and by engine-driven Mtwo files (VDW, Munich, Germany) (n=20). Irrigation was carried out with 2.5% NaOCl in both cases. Samples were taken and determined in colony forming units (CFU) from the root canals before and after the preparation with instruments #25 and #35. Results: Significant reduction in bacterial count was determined after filing at both groups. The number of bacteria kept on decreasing with the extension of apical preparation diameter. There was no significant difference between the preparation sizes in the bacterial counts after hand or engine-driven instrumentation at the same apical size. Statistical analysis was carried out with Mann-Whitney test, paired t-test and independent sample t-test. Conclusions: Significant reduction in CFU was achieved after the root canal preparation completed with 2.5% NaOCl irrigation, both with stainless steel hand or nickel-titanium rotary files. The root canal remained slightly infected after chemo mechanical preparation in both groups. Key words:Chemomechanical preparation, root canal disinfection, nickel-titanium, conicity, greater taper, apical size. PMID:24558545

Effect of metal ions on the reactions of the cumyloxyl radical with hydrogen atom donors. Fine control on hydrogen abstraction reactivity determined by Lewis acid-base interactions.

PubMed

Salamone, Michela; Mangiacapra, Livia; DiLabio, Gino A; Bietti, Massimo

2013-01-09

A time-resolved kinetic study on the effect of metal ions (M(n+)) on hydrogen abstraction reactions from C-H donor substrates by the cumyloxyl radical (CumO(•)) was carried out in acetonitrile. Metal salt addition was observed to increase the CumO(•) β-scission rate constant in the order Li(+) > Mg(2+) > Na(+). These effects were explained in terms of the stabilization of the β-scission transition state determined by Lewis acid-base interactions between M(n+) and the radical. When hydrogen abstraction from 1,4-cyclohexadiene was studied in the presence of LiClO(4) and Mg(ClO(4))(2), a slight increase in rate constant (k(H)) was observed indicating that interaction between M(n+) and CumO(•) can also influence, although to a limited extent, the hydrogen abstraction reactivity of alkoxyl radicals. With Lewis basic C-H donors such as THF and tertiary amines, a decrease in k(H) with increasing Lewis acidity of M(n+) was observed (k(H)(MeCN) > k(H)(Li(+)) > k(H)(Mg(2+))). This behavior was explained in terms of the stronger Lewis acid-base interaction of M(n+) with the substrate as compared to the radical. This interaction reduces the degree of overlap between the α-C-H σ* orbital and a heteroatom lone-pair, increasing the C-H BDE and destabilizing the carbon centered radical formed after abstraction. With tertiary amines, a >2-order of magnitude decrease in k(H) was measured after Mg(ClO(4))(2) addition up to a 1.5:1 amine/Mg(ClO(4))(2) ratio. At higher amine concentrations, very similar k(H) values were measured with and without Mg(ClO(4))(2). These results clearly show that with strong Lewis basic substrates variations in the nature and concentration of M(n+) can dramatically influence k(H), allowing for a fine control of the substrate hydrogen atom donor ability, thus providing a convenient method for C-H deactivation. The implications and generality of these findings are discussed.

Nitrogen conservation in simulated food waste aerobic composting process with different Mg and P salt mixtures.

PubMed

Li, Yu; Su, Bensheng; Liu, Jianlin; Du, Xianyuan; Huang, Guohe

2011-07-01

To assess the effects of three types of Mg and P salt mixtures (potassium phosphate [K3PO4]/magnesium sulfate [MgSO4], potassium dihydrogen phosphate [K2HPO4]/MgSO4, KH2PO4/MgSO4) on the conservation of N and the biodegradation of organic materials in an aerobic food waste composting process, batch experiments were undertaken in four reactors (each with an effective volume of 30 L). The synthetic food waste was composted of potatoes, rice, carrots, leaves, meat, soybeans, and seed soil, and the ratio of C and N was 17:1. Runs R1-R3 were conducted with the addition of K3PO4/ MgSO4, K2HPO4/MgSO4, and KH2PO4/MgSO4 mixtures, respectively; run R0 was a blank performed without the addition of Mg and P salts. After composting for 25 days, the degrees of degradation of the organic materials in runs R0-R3 were 53.87, 62.58, 59.14, and 49.13%, respectively. X-ray diffraction indicated that struvite crystals were formed in runs R1-R3 but not in run R0; the gaseous ammonia nitrogen (NH3-N) losses in runs R0-R3 were 21.2, 32.8, 12.6, and 3.5% of the initial total N, respectively. Of the tested Mg/P salt mixtures, the K2HPO4/ MgSO4 system provided the best combination of conservation of N and biodegradation of organic materials in this food waste composting process.

TRANSMISSION OF COMPOSITE POLYMERIZATION CONTRACTION FORCE THROUGH A FLOWABLE COMPOSITE AND A RESIN-MODIFIED GLASS IONOMER CEMENT

PubMed Central

Castañeda-Espinosa, Juan Carlos; Pereira, Rosana Aparecida; Cavalcanti, Ana Paula; Mondelli, Rafael Francisco Lia

2007-01-01

The purpose of this study was to evaluate the individual contraction force during polymerization of a composite resin (Z-250), a flowable composite (Filtek Flow, FF) and a resin-modified glass ionomer cement (Vitrebond, VB), and the transmission of Z-250 composite resin polymerization contraction force through different thicknesses of FF and VB. The experiment setup consisted of two identical parallel steel plates connected to a universal testing machine. One was fixed to a transversal base and the other to the equipment's cross head. The evaluated materials were inserted into a 1-mm space between the steel plates or between the inferior steel plate and a previously polymerized layer of an intermediate material (either FF or VB) adhered to the upper steel plate. The composite resin was light-cured with a halogen lamp with light intensity of 500 mW/cm2 for 60 s. A force/time graph was obtained for each sample for up to 120 s. Seven groups of 10 specimens each were evaluated: G1: Z-250; G2: FF; G3: VB; G4: Z-250 through a 0.5-mm layer of FF; G5: Z-250 through a 1-mm layer of FF; G6: Z-250 through a 0.5-mm of VB; G7: Z-250 through a 1-mm layer of VB. They were averaged and compared using one-way ANOVA and Tukey test at a = 0.05. The obtained contraction forces were: G1: 6.3N ± 0.2N; G2: 9.8 ± 0.2N; G3: 1.8 ± 0.2N; G4: 6.8N ± 0.2N; G5: 6.9N ± 0.3N; G6: 4.0N ± 0.4N and G7: 2.8N ± 0.4N. The use of VB as an intermediate layer promoted a significant decrease in polymerization contraction force values of the restorative system, regardless of material thickness. The use of FF as an intermediate layer promoted an increase in polymerization contraction force values with both material thicknesses. PMID:19089187

Hot Deformation Behavior of As-Cast 2101 Grade Lean Duplex Stainless Steel and the Associated Changes in Microstructure and Crystallographic Texture

NASA Astrophysics Data System (ADS)

Patra, Sudipta; Ghosh, Abhijit; Singhal, Lokesh Kumar; Podder, Arijit Saha; Sood, Jagmohan; Kumar, Vinod; Chakrabarti, Debalay

2017-01-01

The hot deformation behavior of 2101 grade lean duplex stainless steel (DSS, containing 5 wt pct Mn, 0.2 wt pct N, and 1.4 wt pct Ni) and associated microstructural changes within δ-ferrite and austenite ( γ) phases were investigated by hot-compression testing in a GLEEBLE 3500 simulator over a range of deformation temperatures, T def [1073 K to 1373 K (800 °C to 1100 °C)], and applied strains, ɛ (0.25 to 0.80), at a constant true strain rate of 1/s. The microstructural softening inside γ was dictated by discontinuous dynamic recrystallization (DDRX) at a higher T def [1273 K to 1373 K (1000 °C to 1100 °C)], while the same was dictated by continuous dynamic recrystallization (CDRX) at a lower T def (1173 K (900 °C)]. Dynamic recovery (DRV) and CDRX dominated the softening inside δ-ferrite at T def ≥ 1173 K (900 °C). The dynamic recrystallization (DRX) inside δ and γ could not take place upon deformation at 1073 K (800 °C). The average flow stress level increased 2 to 3 times as the T def dropped from 1273 to 1173 K (1000 °C to 900 °C) and finally to 1073 K (800 °C). The average microhardness values taken from δ-ferrite and γ regions of the deformed samples showed a different trend. At T def of 1373 K (1100 °C), microhardness decreased with the increase in strain, while at T def of 1173 K (900 °C), microhardness increased with the increase in strain. The microstructural changes and hardness variation within individual phases of hot-deformed samples are explained in view of the chemical composition of the steel and deformation parameters ( T def and ɛ).

Improvement of Strength-Toughness-Hardness Balance in Large Cross-Section 718H Pre-Hardened Mold Steel

PubMed Central

Liu, Hanghang; Fu, Paixian; Liu, Hongwei; Li, Dianzhong

2018-01-01

The strength-toughness combination and hardness uniformity in large cross-section 718H pre-hardened mold steel from a 20 ton ingot were investigated with three different heat treatments for industrial applications. The different microstructures, including tempered martensite, lower bainite, and retained austenite, were obtained at equivalent hardness. The microstructures were characterized by using metallographic observations, scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and electron back-scattered diffraction (EBSD). The mechanical properties were compared by tensile, Charpy U-notch impact and hardness uniformity tests at room temperature. The results showed that the test steels after normalizing-quenching-tempering (N-QT) possessed the best strength-toughness combination and hardness uniformity compared with the conventional quenched-tempered (QT) steel. In addition, the test steel after austempering-tempering (A-T) demonstrated the worse hardness uniformity and lower yield strength while possessing relatively higher elongation (17%) compared with the samples after N-QT (14.5%) treatments. The better ductility of A-T steel mainly depended on the amount and morphology of retained austenite and thermal/deformation-induced twined martensite. This work elucidates the mechanisms of microstructure evolution during heat treatments and will highly improve the strength-toughness-hardness trade-off in large cross-section steels. PMID:29642642

Deflection in Tapered Cantilever Beams Deflection (Gap Opening) in Double Cantilever Type Fracture Toughness Specimens.

DTIC Science & Technology

1985-08-01

o10 ------- --------- tx] (26) t 5 t bE ho 2(h0+tx) 2 and as before 12 9 1 p ho + tx 2ho + 3tx bend3 + bE ho 2(ho+tX)2 txcos2 At the limit, as t...h0+tx) 2tx Therefore P 1 x P x lim 6 bend3 n2 -(-) - 4 -(;) t+o bE 3ho bE h 22 which, except for the sign, is the same as that arrived at in Eq. (9

Low Temperature Deposition of Diamond Films for Optical Coatings

DTIC Science & Technology

1989-10-18

Optical Materials, " Infrared Opfical Materials VI, Solomon Musikant , Editor, Proc. SPIE 929, p. 65 (1988). 14. M.S. Wong, R. Meilunas, T.P. Ong and...of the grinding. The small arrow indicates the materials transferred from the steel bearing. So0 600 ’-400 200- At 00 n 0 20 40 60 So t (min) r.m.s

Gas Furnace with Pulsed Feeding of the Heating Agent for Volume Precision Heat Treatment of CCM Rolls

NASA Astrophysics Data System (ADS)

Moroz, V. I.; Egorova, V. M.; Gusev, S. V.

2001-05-01

A standard chamber batch furnace of the Severstal' plant has been modified for precision heat treatment of CCM rolls. The certification tests of a charge of rolls from steel 24KhM1F have shown the technical and economical advantages of the new design.

Study of Aerospace Materials, Coatings, Adhesions and Processes. Aircraft Icing Processes. Volume 2.

DTIC Science & Technology

1984-09-14

la direccio’n del eje de la son - da. DATOS ELECTRICOS Rint’erna 20.26 . R(OC) =5.35 Q R(22 0 C).. 5.93 Q R(100 0 C) 7.43 . Roperacio’n... son las constantes de calibraci6n propias del sensor. 1INT A FN. de Informe I-231/S10/84.076Pg. . La temperatura de funcionamiento se deterrnin6 por l...funcionamiento del sensor, T la temperatura ambiente, la densidad y v la velocidad. A, B y n son las constantes de cal- z braci6n propias del

Low temperature studies of the removal reactions of 1CH2 with particular relevance to the atmosphere of Titan

NASA Astrophysics Data System (ADS)

Douglas, Kevin; Blitz, Mark A.; Feng, Wuhu; Heard, Dwayne E.; Plane, John M. C.; Slater, Eloise; Willacy, Karen; Seakins, Paul W.

2018-03-01

Methylene, CH2, is one of the major photolysis products of methane by Lyman-α radiation and is involved in the photochemistry of the atmospheres of Titan and the giant planets. The kinetics of the reactions of the first excited state of methylene, 1CH2, with He, N2, O2, H2 and CH4 have been measured over the temperature range 43-160 K by pulsed laser photolysis, monitoring 1CH2 removal by laser induced fluorescence. Low temperatures were obtained with either a pulsed Laval expansion (43-134 K) or a, slow flow reaction cell (160 K). The rate coefficients for the reactions with N2, O2, H2 and CH4 all showed a strong negative temperature dependence. In combination with other literature data, the rate coefficients can be parameterised as: kHe(43 < T/K < 800) = (1.90 ± 0.23) × 10-12 × (T/298)1.74±0.16 × exp((88±23)/T) kN2(43 < T / K < 800) = (2.29 ± 1.12) × 10-12 × (T/298)-2.15±1.38 × exp((-74±96)/T) + (3.91 ± 0.78) × 10-11 × exp((-469±114)/T) kO2(43 < T / K < 300) = (6.16 ± 1.09) × 10-11 × (T/298)-0.65±0.14 kH2(43 < T / K < 800) = (1.10 ± 0.04) × 10-10 × (T/298)-0.40±0.06 × exp((11.1±6.9)/T) kCH4(43 < T / K < 475) = (8.20 ± 0.46) × 10-11 × (T/298)-0.93±0.10 × exp((-20.5±12.8)/T) For the reactions of 1CH2 with H2 and CH4, the branching ratio for quenching to ground state, 3CH2, vs chemical reaction was also determined at 160 and 73 K. The values measured (H2: 0.39 ± 0.10 at 160 K, 0.78 ± 0.15 at 73 K; CH4: 0.49 ± 0.09 at 160 K, 0.64 ± 0.19 at 73 K) confirm trends of an increased proportion of reactive loss with increasing temperature determined at higher temperatures. The impacts of the new measurements for Titan's atmosphere have been ascertained using a 1D chemistry and transport model. A significant decrease (∼40%) in the mixing ratio of ethane between 800 and 1550 km is calculated due to the decrease contribution of methyl production from the reaction of 1CH2 with CH4, with smaller increases in the concentrations of ethene and acetylene. Ethene production is enhanced by more methylene being converted to methylidene, CH, and the subsequent reaction of CH with CH4 to generate ethene. Photolysis of ethene is the major route to acetylene formation.

High Energy Solid State and Free Electron Laser Systems in Tactical Aviation

DTIC Science & Technology

2005-06-01

specifically neodymium and ytterbium doped yttrium aluminum garnet (Nd:YAG and Yb:YAG) have been shown to produce pump absorption efficiencies (i.e...Search Radar Dish Aluminum Alloy 2.71 10.0 0.91 321 932 300 22.1 SAM nosecone Ceramic* 3.0 1.0 0.9 1600 3300 250 12.1 T-72 Tank Armor Steel...development at Lawrence Livermore National Laboratory, is the solid-state heat capacity laser, which is an array of diode- pumped neodymium-doped gadolinium

Effect of Nd:YAG laser light on post-extractive socket healing in rats treated with zoledronic acid and dexamethasone

NASA Astrophysics Data System (ADS)

Mergoni, Giovanni; Merigo, Elisabetta; Passerini, Pietro; Corradi, Domenico; Maestri, Roberta; Bussolati, Ovidio; Bianchi, Massimiliano; Sala, Roberto; Govoni, Paolo; Namour, Samir; Vescovi, Paolo

2016-03-01

Introduction The effect of low level laser therapy (LLLT) on the healing process could be useful for the prevention of post-extractive Bisphosphonate-related Osteonecrosis of the Jaws (BRONJ). The aim of the study was to investigate the effect of LLLT on the post-extractive socket healing in rats treated with zoledronic acid and dexamethasone. Material and Methods Thirty male Sprague-Dawley rats were divided in 4 groups: control group (C, n = 5), laser group (L, n = 5), treatment group (T, n = 10) and treatment plus laser group (T+L, n = 10). Rats of group T and T+L received zoledronate 0,1 mg/Kg and dexamethasone 1 mg/Kg every 2 days for 10 weeks. Rats of group C and L were infused with vehicle. After 9 weeks the first maxillary molars were extracted in all rats. Rats of groups L and T+L received laser therapy (Nd:YAG, 1064 nm, 1.25W, 15Hz, 5 min, 14.37 J/cm2) in the socket area at days 0, 2, 4 and 6 after surgery. At 8 days from extraction, the sockets were clinically assessed with a grading score and the wound area was measured with a dedicate software. Histomorphometric evaluation and western blot analysis of osteopontin and osteocalcin expression were performed. Results Group T+L showed a trend toward a better clinical grading score compared to group T (grade I 22% Vs 28 % - grade II 56% Vs 28% - grade III 22% Vs 44%, respectively). The average wound area was similar among the groups. Inhibition of osteoclastic alveolar bone resorption was found in groups T and T+L (P<0.001). Rats of groups L and T+L showed a significant higher expression of osteocalcin compared to rats of groups C and T (C=0.3993; L=1.394; T=0.2922; T+L=1.156; P=0.0001). The expression of osteopontin did not show significant differences in the groups treated with Nd:YAG compared to the ones that did not receive laser irradiation. Conclusion Our findings suggest that laser irradiation after tooth extraction can promote osteoblast differentiation, as demonstrated by the higher expression of osteocalcin. Thus, laser irradiation could be considered a way to improve socket healing in conditions at risk for MRONJ development.

Extremely bulky secondary phosphinoamines as substituents for sterically hindered aminosilanes.

PubMed

Böttcher, Tobias; Jones, Cameron

2015-09-07

The synthesis of a series of extremely bulky secondary amines with a phosphine function, Ar(†)(PR2)NH (Ar(†) = C6H2{C(H)Ph2}2Pr(i)-2,6,4; R = Ph, NEt2, NPr(i)2) is described. Deprotonation with either n-BuLi or KH yields the respective alkali metal amides in some cases. Their reaction with the chlorosilanes SiCl4, HSiCl3, Cl2SiPh2, Cl3Si-SiCl3 and Si5Cl10 allows access to monomeric molecular compounds bearing the extremely bulky amino substituents via salt elimination. The products obtained may serve as precursors for subsequent reduction reactions to access sterically protected low valent and low coordinate silicon compounds.

BILIRUBIN CONCENTRATIONS IN CLINICALLY HEALTHY AND DISEASED CAPTIVE WATERBUCK (KOBUS ELLIPSIPRYMNUS) AT THE SAN DIEGO ZOO SAFARI PARK.

PubMed

Sadler, Ryan A; Lamberski, Nadine; Christopher, Mary M

2016-06-01

Captive waterbuck ( Kobus ellipsiprymnus ) that appear clinically healthy have been noted to have high serum bilirubin concentrations compared with other ruminants; however, questions remain about the physiologic factors affecting bilirubin concentration and its potential association with underlying disease and icteric serum or mucous membranes. Serum bilirubin concentrations of healthy and diseased waterbuck housed at the San Diego Zoo Safari Park from 1989 to 2012 were retrospectively analyzed to determine any link between icteric serum, total bilirubin concentration (tBili), and disease entities in this species. Total bilirubin and direct (dBili) bilirubin concentrations and the prevalence of icteric serum were compared by subspecies, age group, and health status; associations with complete blood count and biochemical results and clinical diagnosis were assessed. No significant differences were found in tBili or dBili between Ellipsen (n = 32) and Defassa (n = 29) subspecies or in juveniles (n = 22) versus adults (n = 39). Clinically healthy waterbuck (n = 40) had significantly higher tBili (mean ± 2SD, 7.9 ± 1.2 mg/dl; P < 0.001) and dBili (3.7 ± 1.0 mg/dl; P < 0.001) than did diseased waterbuck (n = 21; tBili: 4.9 ± 2.56 mg/dl; dBili: 2.2 ± 0.8 mg/dl). No waterbuck had icteric tissues on physical examination. Twelve (19.7%) waterbuck (six healthy, six diseased) had icteric serum. Few minor correlations were seen between tBili or dBili and clinical, laboratory, or necropsy evidence of disease, though an inverse correlation between dBili and blood glucose was noted. Of the 40 healthy animals, reference intervals were calculated for tBili (5.5-10.3 mg/dl), dBili (1.7-5.7 mg/dl), and indirect bilirubin (2.2-6.2 mg/dl). These results suggest healthy waterbuck have relatively high tBili and dBili compared with related species. Icteric serum may be seen in up to 15% of healthy animals in the absence of icteric tissues.

WAZP Observations during MILDEX October-November 1983.

DTIC Science & Technology

1984-03-01

SIGMAR T TAPE 16 NEIL BROWN SENSOR FILE 16 01T 10 20 C30 s- 60 ’.4 70 10 15 20 22 24 26 33.0 33.5 34..0 * V S S *** * 22o 26-OCT-83 22 *37 TEMP, SALINITY... SIGMAR T TAPE 17 NEIL BROWN SENSOR FILE 3 0 10 20 3 0 I- so- .1*r 60 70 a a wl10 15 20 22 24. 26 33.0 33.5 34..0 26-OCT-83 23󈧕 TEMIP, SFLINITY

Nha Trang Apt.,Vietnam. Revised Uniform Summary of Surface Weather Observations (RUSSWO). Parts A-F

DTIC Science & Technology

1971-01-29

DO-02 boi 647 07 $o63 yeo0 be?, 1190 lv 9@4 21.4 146 (6el 748 J-05 el 09.3 L.e 6.0 19o4 0i,9 1067 1.o i$05 25.3 13.a 603 971 0 0 hO iha - 4 3 70. 790...Temperature I ReId ti!n 32831 5) 4 II 9Z 7𔃺 2P I 5 I= 7IP -<OF I -T32F n67F 72 eO e93 F Total < wet BoI 2 99o51o 117 ’ 3, 6,11 93t i , 7POO.t~: ~?6...22 23 24 25 26 27-2829- 301 31 D B. W B FDry B.uIb Wc Bulb ew Porn ? 7t 7 all/ 87 i _,._7 a 4 834*3Is$ Ill1621 208 bo/ 79 Jll 7.0’l 3.1 2.6 7 2 194

Induced magnetic moment in stainless steel components of orthodontic appliances in 1.5 T MRI scanners

PubMed Central

Rollins, Nancy K.; Liang, Hui; Park, Yong Jong

2015-01-01

Purpose: Most orthodontic appliances are made of stainless steel materials and induce severe magnetic susceptibility artifacts in brain MRI. In an effort for correcting these artifacts, it is important to know the value of induced magnetic moments in all parts of orthodontic appliances. In this study, the induced magnetic moment of stainless steel orthodontic brackets, molar bands, and arch-wires from several vendors is measured. Methods: Individual stainless steel brackets, molar bands, and short segments of arch-wire were positioned in the center of spherical flask filled with water through a thin plastic rod. The induced magnetic moment at 1.5 T was determined by fitting the B0 map to the z-component of the magnetic dipole field using a computer routine. Results: The induced magnetic moment at 1.5 T was dominated by the longitudinal component mz, with a small contribution from the transverse components. The mz was insensitive to the orientation of the metal parts. The orthodontic brackets collectively dominated the magnetic dipole moment in orthodontic appliances. In brackets from six vendors, the total induced mz from 20 brackets for nonmolar teeth ranged from 0.108 to 0.158 (median 0.122) A ⋅ m2. The mz in eight molar bands with bracket attachment from two vendors ranged from 0.0004 to 0.0166 (median 0.0035) A ⋅ m2. Several full length arch wires had induced magnetic moment in the range of 0.006–0.025 (median 0.015) A ⋅ m2. Conclusions: Orthodontic brackets collectively contributed most to the total magnetic moment. Different types of brackets, molar bands, and arch wires all exhibit substantial variability in the induced magnetic moment. PMID:26429261

Oxidation behavior of a ferritic stainless steel Crofer22 APU with thermal cycling

NASA Astrophysics Data System (ADS)

Song, MyoungYoup; Duong, Anh T.; Mumm, Daniel R.

2013-01-01

Crofer22 APU specimens were prepared by grinding with grit 80 and 120 SiC grinding papers and were thermally cycled. The variation in oxidation behavior with thermal cycling was then investigated. Observation of microstructure, measurement of area specific resistance (ASR), analysis of the atomic percentages of the elements by EDX, and XRD analysis were performed. XRD patterns showed that the (Cr, Mn)3O4 spinel phase grew on the surface of the Crofer22 APU samples ground with grit 120. For the samples ground with grit 80, the ASR increased as the number of thermal cycles increased. Plots of ln (ASR/T) vs. 1/T for the samples ground with grit 80 after n = 4, 20 and 40 exhibited good linearity, and the apparent activation energies were between 63.7 kJ/mole and 76.3 kJ/mole.

Energy and Tangential Momentum Accommodation on Different Flashed Tungsten and Gas Covered Tungsten Surfaces.

DTIC Science & Technology

1981-10-29

and r. (r. co2 0o/wn and r’ = rw/co, where co is the ideal gas free space sound velocity, po is the equilibrium density, w is the angular frequency, q...LAC 1, 1 u s IA’ xI i i k-h t I t i. - LI t HiOil, tI it I o) %’t.liii I t and a 1 -~i1 )t lulil PI t. AIs o 1 v vii in i lit, t ll 1 1 k FAP vst lics

Preparation of Keratin Hydrolysate from Chicken Feathers and Its Application in Cosmetics.

PubMed

Mokrejš, Pavel; Huťťa, Matouš; Pavlačková, Jana; Egner, Pavlína

2017-11-27

Keratin hydrolysates (KHs) are established standard components in hair cosmetics. Understanding the moisturizing effects of KH is advantageous for skin-care cosmetics. The goals of the protocol are: (1) to process chicken feathers into KH by alkaline-enzymatic hydrolysis and purify it by dialysis, and (2) to test if adding KH into an ointment base (OB) increases hydration of the skin and improves skin barrier function by diminishing transepidermal water loss (TEWL). During alkaline-enzymatic hydrolysis feathers are first incubated at a higher temperature in an alkaline environment and then, under mild conditions, hydrolyzed with proteolytic enzyme. The solution of KH is dialyzed, vacuum dried, and milled to a fine powder. Cosmetic formulations comprising from oil in water emulsion (O/W) containing 2, 4, and 6 weight% of KH (based on the weight of the OB) are prepared. Testing the moisturizing properties of KH is carried out on 10 men and 10 women at time intervals of 1, 2, 3, 4, 24, and 48 h. Tested formulations are spread at degreased volar forearm sites. The skin hydration of stratum corneum (SC) is assessed by measuring capacitance of the skin, which is one of the most world-wide used and simple methods. TEWL is based on measuring the quantity of water transported per a defined area and period of time from the skin. Both methods are fully non-invasive. KH makes for an excellent occlusive; depending on the addition of KH into OB, it brings about a 30% reduction in TEWL after application. KH also functions as a humectant, as it binds water from the lower layers of the epidermis to the SC; at the optimum KH addition in the OB, up to 19% rise in hydration in men and 22% rise in women occurs.

Application experience of grade 10Kh9MFB chromium steel for steam shutoff and control valve bodies

NASA Astrophysics Data System (ADS)

Skorobogatykh, V. N.; Schenkova, I. A.; Danyushevskiy, I. A.; Grin', E. A.; Levkov, L. Ya.; Prudnikov, D. A.; Zhuravlev, D. N.; Bazhenov, A. M.

2017-04-01

In 2014-2015, the engineers of JSC "NPO "TsNIITMash", in cooperation with JSC "Energomash (Chekhov)—ChZEM", developed a technology for manufacturing D u = 250 mm valve bodies from 10Kh9MFB chromium steel by electroslag melting (ESM) and produced their pilot copies within the frame of import substitution program. This article provides results of research into determining the design values of metal characteristics, including short-term mechanical properties at working temperatures and impact and long-term strength. The test specimens have been sampled from the following four zones: bottom, central, branch-pipe, and head. Tensile short-term rupture testing has been performed at temperatures of 350, 450, 500, 550, 600, and 650°C. Testing for long-term strength has been carried out at temperatures of 550, 575, 600, and 625°C and stresses of 156.8, 137.2, 117.6, and 98 MPa. To estimate brittle fracture resistance, impact-strength tests have been run at temperatures of-20 and-10°C; 20 and 50°C. The specimens have been sampled from the middle of the blank section. All short-term mechanical properties and impact strength are in agreement with the requirements imposed on the metal of hot-deformed steam piping made of 10Kh9MFB steel as per TU (Technical Conditions) 14-3R-55-2001. The absence of microliquation of alloying elements and the high homogeneity of chemical composition (as demonstrated with nine specimens) have also been experimentally confirmed. Metallographic analysis has shown that the structure of the tested metal is that of tempered martensite with local areas of tempered bainite. Overall, the microscopic structure of metal is practically the same in all the studied zones. Service-life calculation of pilot valve bodies has proved conformity with the safety-margin regulations. Such properties of electroslag melting blank as long-term strength and allowable stress correspond to the level of deformed metal and to regulations.

IR detector system based on high-Tc superconducting bolometer on SI membrane

NASA Astrophysics Data System (ADS)

Burnus, M.; Hefle, G.; Heidenblut, T.; Khrebtov, Igor A.; Laukemper, J.; Michalke, W.; Neff, H.; Schwierzi, B.; Semtchinova, O. K.; Steinbeiss, E.; Tkachenko, A. D.

1996-06-01

An infrared detector system based on high-T(subscript c) superconducting (HTS) membrane bolometer is reported. Superconducting transition-edge bolometer has been manufactured by silicon micromachining using an epitaxial GdBa(subscript 2)Cu(subscript 3)O(subscript 7-x) film on an epitaxial yttria- stabilized zirconia buffer layer on silicon. The active area of the element is 0.85 X 0.85 mm(superscript 2). The membrane thickness is 1 micrometers , those of the buffer layer and HTS films are 50 nm. The detectivity of bolometer, D(superscript *), is 3.8 X 10(superscript 9) cm Hz(superscript 1/2) W(superscript -1) at 84.5 K and within the frequency regime 100 < f < 300 Hz. The optical response is 580 V/W at time constant 0.4 ms. This is one of the fastest composite type HTS-bolometer ever reported. The bolometer is mounted on a metal N(subscript 2)-liquid cryostat, which fits the preamplifier. With the volume of N(subscript 2)-reservoir being 0.1 liter, the cryostat holds nitrogen for about 8 hours. Using only wire heater with constant current, the temperature stability of about 0.03 K/h is achieved. The detector system can be used in IR- Fourier spectroscopy at wavelengths longer than the typical operating range of semiconductor detectors (wavelength greater than about 20 micrometers ).

Fracture toughness of irradiated modified 9Cr-1Mo steel

NASA Astrophysics Data System (ADS)

Kim, Sung Ho; Yoon, Ji-Hyun; Ryu, Woo Seog; Lee, Chan Bock; Hong, Jun Hwa

2009-04-01

The effects of irradiation on fracture toughness of modified 9Cr-1Mo steel in the transition region were investigated. Half size precracked Charpy specimens were irradiated up to 1.2 × 10 21n/cm 2 ( E > 0.1 MeV) at 340 °C and 400 °C in the Korean research reactor. The irradiation induced transition temperature shift for a modified 9Cr-1Mo was evaluated by using the Master Curve methodology. The T0 temperature for the unirradiated specimens were measured as -67.7 °C and -72.4 °C from the tests with standard PCVN (precracked charpy V-notch) and half sized PCVN specimens, respectively. The T0 shifts of specimens after irradiation at 340 °C and 400 °C were 70.7 °C and 66.1 °C, respectively. The Weibull slopes for the fracture toughness data obtained from the unirradiated and irradiated modified 9Cr-1Mo steels were determined to confirm the applicability of master curve methodology to modified 9Cr-1Mo steel.

Electron impact excitation of NeIII intercombination lines

NASA Astrophysics Data System (ADS)

Daw, Adrian; McLaughlin, Brendan M.; Bell, Kenneth L.

2000-06-01

Observations on the spectra of doubly ionized neon (NeIII) have been recently recorded below 25O Å(A. E. Livington, R. Buttner, A. S. Zacarias, B. Kraus, K-H Schartner, F. Folkmann and P. H. Mokler, J. Opt. Soc. Am. B 14) 522-525 (1997).. This work together with previous studies give line intensies which may be used as density diagnostics but required accurate collision strengths and transition probabilities for their interpretation. Recent studies on electron collisions with NeIII ions using the R-matrix approach (B. M. McLaughlin and K. L. Bell, J. Phys. B. 33), 597 (2000). for Δ n=0 transitions, illustrated the importance of including n=3 and 4 levels in the calculations compared to previous work. (K. Butler and C. Mendoza, Mon. Not. R. Astr. Soc. 208), 17 (1984). Particular emphasis is now placed on transitions to the intercombination 2s^22p^3[^4S^o]3s ^3,5S^o levels and to the other n=3 levels where comparison can be made with previous distorted-wave work. The calculations of fine-structure transitions by electron impact, to and within these multiplets of NeIII provide much needed accurate data for astrophysical models. Further details and a comprehensive set of results will be presented at the meeting.

N2O and CH4 emissions from N-fertilized rice paddy soil can be mitigated by wood vinegar application at an appropriate rate

NASA Astrophysics Data System (ADS)

Sun, Haijun; Feng, Yanfang; Ji, Yang; Shi, Weiming; Yang, Linzhang; Xing, Baoshan

2018-07-01

To understand the impacts of wood vinegar (WV), a by-product of biochar production, on N2O and CH4 emissions and their total global warming potential (GWPt) from N-fertilized rice paddy soil, a soil column experiment was conducted using three treatments: 240 kg urea-N ha-1 accompanied with 0, 5, and 10 t WV ha-1, respectively. Results showed that N2O and CH4 emission flux patterns were dominated by water regime of rice growth cycle, which was independent with WV application. The total N2O, CH4 emission loads and GWPt over rice season of three N received treatments were 6.41-8.85 kg ha-1, 127.7-405.0 kg ha-1, and 5.24-12.03 t CO2-e ha-1, respectively. Rice seasonal N2O and CH4 emissions were synchronously mitigated by 22.4% and 36.4%, respectively, when WV was applied at 5 t ha-1. Consequently, 5 t ha-1 WV treatment reduced 31.5% of GWPt compared with the urea treatment. In addition, 10 t ha-1 WV treatment exerted a more positive effect on suppressing N2O with 27.6% reduction. However, it increased GWPt by 57.2% because its CH4 emission load was increased by 101.8%. In conclusion, WV amendment applied at an appropriate rate (5 t ha-1) or combination with other CH4 control technologies were suggested to reduce both N2O and CH4 emissions and thereby the GWPt in N-fertilized rice paddy soil.

Avoiding chromium transport from stainless steel interconnects into contact layers and oxygen electrodes in intermediate temperature solid oxide electrolysis stacks

NASA Astrophysics Data System (ADS)

Schlupp, Meike V. F.; Kim, Ji Woo; Brevet, Aude; Rado, Cyril; Couturier, Karine; Vogt, Ulrich F.; Lefebvre-Joud, Florence; Züttel, Andreas

2014-12-01

We investigated the ability of (La0.8Sr0.2)(Mn0.5Co0.5)O3-δ (LSMC) and La(Ni0.6Fe0.4)O3-δ (LNF) contact coatings to avoid the transport of Cr from steel interconnects to solid oxide electrolysis electrodes, especially to the anode. The transport of chromium from commercial Crofer 22 APU (ThyssenKrupp) and K41X (AISI441, Aperam Isbergues) steels through LSMC and LNF contact coatings into adjacent (La0.8Sr0.2)MnO3-δ (LSM) oxygen electrodes was investigated in an oxygen atmosphere at 700 °C. Chromium concentrations of up to 4 atom% were detected in the contact coatings after thermal treatments for 3000 h, which also lead to the presence of chromium in adjacent LSM electrodes. Introduction of a dense (Co,Mn)3O4 coating between steel and contact coating was necessary to prevent the diffusion of chromium into contact coatings and electrodes and should lead to extended stack performance and lifetime.

Causes of distal volcano-tectonic seismicity inferred from hydrothermal modeling

USGS Publications Warehouse

Coulon, Cecile A.; Hsieh, Paul A.; White, Randall A.; Lowenstern, Jacob B.; Ingebritsen, Steven E.

2017-01-01

Distal volcano-tectonic (dVT) seismicity typically precedes eruption at long-dormant volcanoes by days to years. Precursory dVT seismicity may reflect magma-induced fluid-pressure pulses that intersect critically stressed faults. We explored this hypothesis using an open-source magmatic-hydrothermal code that simulates multiphase fluid and heat transport over the temperature range 0 to 1200 °C. We calculated fluid-pressure changes caused by a small (0.04 km3) intrusion and explored the effects of flow geometry (channelized vs. radial flow), magma devolatilization rates (0–15 kg/s), and intrusion depths (5 and 7.5 km, above and below the brittle-ductile transition). Magma and host-rock permeabilities were key controlling parameters and we tested a wide range of permeability (k) and permeability anisotropies (kh/kv), including k constant, k(z), k(T), and k(z, T, P) distributions, examining a total of ~ 1600 realizations to explore the relevant parameter space. Propagation of potentially causal pressure changes (ΔP ≥ 0.1 bars) to the mean dVT location (6 km lateral distance, 6 km depth) was favored by channelized fluid flow, high devolatilization rates, and permeabilities similar to those found in geothermal reservoirs (k ~ 10− 16 to 10− 13 m2). For channelized flow, magma-induced thermal pressurization alone can generate cases of ∆ P ≥ 0.1 bars for all permeabilities in the range 10− 16 to 10− 13 m2, whereas in radial flow regimes thermal pressurization causes ∆ P < 0.1 bars for all permeabilities. Changes in distal fluid pressure occurred before proximal pressure changes given modest anisotropies (kh/kv ~ 10–100). Invoking k(z,T,P) and high, sustained devolatilization rates caused large dynamic fluctuations in k and P in the near-magma environment but had little effect on pressure changes at the distal dVT location. Intrusion below the brittle-ductile transition damps but does not prevent pressure transmission to the dVT site.

Residual pathological stage at radical cystectomy significantly impacts outcomes for initial T2N0 bladder cancer.

PubMed

Isbarn, Hendrik; Karakiewicz, Pierre I; Shariat, Shahrokh F; Capitanio, Umberto; Palapattu, Ganesh S; Sagalowsky, Arthur I; Lotan, Yair; Schoenberg, Mark P; Amiel, Gilad E; Lerner, Seth P; Sonpavde, Guru

2009-08-01

We hypothesized that in patients with T2N0 stage disease at transurethral bladder tumor resection a lower residual cancer stage (P1N0 or less) at radical cystectomy may correlate with improved outcomes relative to those with residual P2N0 disease. We analyzed 208 patients with T2N0 stage disease at transurethral bladder tumor resection whose tumors were organ confined at radical cystectomy (P2 or lower, pN0). None received perioperative chemotherapy. Kaplan-Meier as well as univariable and multivariable Cox regression models addressed the effect of residual pT stage at radical cystectomy on recurrence and cancer specific mortality rates. Covariates consisted of age, gender, grade, lymphovascular invasion, carcinoma in situ, number of lymph nodes removed and year of surgery. Residual pT stage at radical cystectomy was P0 in 24 (11.5%) patients, Pa in 9 (4.3%), PCIS in 22 (10.6%), P1 in 35 (16.8%) and P2 in 118 (56.7%). Median followup of censored patients was 55.7 months for recurrence and 52.1 months for cancer specific mortality analyses. The 5-year recurrence-free survival rates of patients with P0/Pa/PCIS, P1 and P2 stage disease were 100%, 85% and 75%, respectively. The 5-year cancer specific survival rates for the same cohorts were 100%, 93% and 81%, respectively. On multivariable analysis the effect of residual stage P1 or lower at radical cystectomy achieved independent predictor status for recurrence (adjusted HR 0.20, p = 0.002) and cancer specific mortality (adjusted HR 0.24, p = 0.02). Down staging from initial T2N0 bladder cancer at transurethral bladder tumor resection to lower stage at radical cystectomy significantly reduces recurrence and cancer specific mortality. Further validation of this finding is warranted.

High temperature gas nitriding and tempering in 17Cr-1Ni-0.5C-0.4V steel

NASA Astrophysics Data System (ADS)

Kong, J. H.; Lee, D. J.; On, H. Y.; Park, S. J.; Kim, S. K.; Kang, C. Y.; Sung, J. H.; Lee, H. W.

2010-12-01

High temperature gas nitriding (HTGN) at 1050 °C and tempering of a 17Cr-1Ni-0.5C-0.4V (CNV) steel were experimentally investigated. The phases appearing in the surface layer of the HTGN-treated steel were martensite and austenite with mostly Cr2N precipitates that were formed by permeated nitrogen, and a small amount of Cr23C6 and VN precipitates. The reverse migration of carbon hindered the diffusion of nitrogen when nitrogen permeated from the surface to the interior, which resulted in the accumulation of nitrogen on the outermost surface. The strong affinity between nitrogen and chromium atoms induced the diffusion of chromium from the interior to the surface, leading to the substitution of Cr23C6 for Cr2N. After tempering the HTGN-treated steel at 500 °C, the dense precipitates of Cr2N and the increased martensite phase in the surface layer led to secondary hardening, which increased the hardness value up to 901 Hv.

SEEING THROUGH THE RING: NEAR-INFRARED PHOTOMETRY OF V582 MON (KH 15D)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arulanantham, Nicole A.; Herbst, William; Cody, Ann Marie

2016-04-15

We examine the light and color evolution of the T Tauri binary KH 15D through photometry obtained at wavelengths between 0.55 and 8.0 μm. The data were collected with A Novel Dual Imaging CAMera (ANDICAM) on the 1.3 m SMARTS telescope at Cerro-Tololo Inter-American Observatory and with InfraRed Array Camera on the Spitzer Space Telescope. We show that the system’s circumbinary ring, which acts as a screen that covers and uncovers different portions of the binary orbit as the ring precesses, has reached an orientation where the brighter component (star B) fully or nearly fully emerges during each orbital cycle.more » The fainter component (star A) remains fully occulted by the screen at all phases. The leading and trailing edges of the screen move across the sky at the same rate of ∼15 m s{sup −1}, consistent with expectation for a ring with a radius and width of ∼4 au and a precession period of ∼6500 years. Light and color variations continue to indicate that the screen is sharp edged and opaque at VRIJH wavelengths. However, we find an increasing transparency of the ring edge at 2.2, 3.6, and 4.5 μm. Reddening seen at the beginning of the eclipse that occurred during the CSI 2264 campaign particularly suggests selective extinction by a population of large dust grains. Meanwhile, the gradual bluing observed while star B is setting is indicative of forward scattering effects at the edge of the ring. The spectral energy distribution of the system at its bright phase shows no evidence of infrared excess emission that can be attributed to radiation from the ring or other dust component out to 8 μm.« less

Estimation of Inventory Item Demand Distributions: Modeling Item Migration at the Defense Electronics Supply Center.

DTIC Science & Technology

1985-12-01

LLEC𔃺,𔃾 PEAD(I.5E31 IFIRST 5 --: FJP ..... iEH,-, V 15)i :cN’ER, T’ COS’, J:.,. ATE EPiRE ... . F - 8E0P I. 1 PFSTC = :YEAR * : 65 , IPA 2 D.J’T FOF...RIL 0 209 1391 135 5 2 1741 ACTUAL 25 19 3262 196 2 0 3503 SIMULATED RIM 0 65 82 1456 125 40 1768 ACTUAL 13 16 236 1677 110 5 2057 SIMULATED RIHI 0 9...117 2540 149 22 2975 ACTUAL 6 61 220 1462 90 a 1847 SIMULATED RHl 0 10 1 70 700 117 899 ACTUAL 2 7 1 97 476 112 65 SIMULATED RIH2 0 5 0 0 12 1419 1436

Maui Optical Site, Mt. Halekulia, Hawaii, Revised Uniform Summary of Surface Weather Observations (RUSSWO) Parts C, E-F.

DTIC Science & Technology

1980-09-23

PAGE 1 no2IJ1L HouRs I.. S. T .) Tomp. _ _WET BULB TEMPERATURE DEPRESSION (F) TOTAL TOTAL (F) 0_1__2_.4 1 5. 0111- 12113.-14 15.-16117.-1S119.-20 21.22...80 JAN STATION STATION NAME YEARS MONTH PAGE 1 (13110-1 1501711 HOURS (L. S. T .) Temp. _ WET BULB TEMPERATURE DEPRESsION (F) J TOTAL TOTAL (F) o 1. T 3...NAME YEARS MONTH PAGE 1 111nn-nAnn HOURS t . S. T ,) Temp. WET BULB TEMPERATURE DEPRESSION (P) TOTAL TOTAL F 0 1.? 3-4 5.6 7-S 9.10 11 1213 14 1 16

Investigations on Laser Beam Welding of Different Dissimilar Joints of Steel and Aluminum Alloys for Automotive Lightweight Construction

NASA Astrophysics Data System (ADS)

Seffer, Oliver; Pfeifer, Ronny; Springer, André; Kaierle, Stefan

Due to the enormous potential of weight saving, and the consequential reduction of pollutant emissions, the use of hybrid components made of steel and aluminum alloys is increasing steadily, especially concerning automotive lightweight construction. However, thermal joining of steel and aluminum is still being researched, due to a limited solubility of the binary system of iron and aluminum causing the formation of hard and brittle intermetallic phases, which decrease the strength and the formability of the dissimilar seam. The presented results show the investigation of laser beam welding for joining different dissimilar hybrid components of the steel materials HX220LAD+Z100, 22MnB5+AS150 and 1.4301, as well as the aluminum alloy AA6016-T4 as a lap joint. Among other things, the influences of the energy per unit length, the material grade, the sheet thickness t, the weld type (lap weld, fillet weld) and the arrangement of the base materials in a lap joint (aluminum-sided irradiation, steel-sided irradiation) on the achievable strengths are analyzed. The characterization of the dissimilar joints includes tensile shear tests and metallographic analyses, depending on the energy per unit length.

Bacteriocidal activity of sanitizers against Enterococcus faecium attached to stainless steel as determined by plate count and impedance methods.

PubMed

Andrade, N J; Bridgeman, T A; Zottola, E A

1998-07-01

Enterococcus faecium attached to stainless steel chips (100 mm2) was treated with the following sanitizers: sodium hypochlorite, peracetic acid (PA), peracetic acid plus an organic acid (PAS), quaternary ammonium, organic acid, and anionic acid. The effectiveness of sanitizer solutions on planktonic cells (not attached) was evaluated by the Association of Official Analytical Chemists (AOAC) suspension test. The number of attached cells was determined by impedance measurement and plate count method after vortexing. The decimal reduction (DR) in numbers of the E. faecium population was determined for the three methods and was analyzed by analysis of variance (P < 0.05) using Statview software. The adhered cells were more resistant (P < 0.05) than nonadherent cells. The DR averages for all of the sanitizers for 30 s of exposure were 6.4, 2.2, and 2.5 for the AOAC suspension test, plate count method after vortexing, and impedance measurement, respectively. Plate count and impedance methods showed a difference (P < 0.05) after 30 s of sanitizer exposure but not after 2 min. The impedance measurement was the best method to measure adherent cells. Impedance measurement required the development of a quadratic regression. The equation developed from 82 samples is as follows: log CFU/chip = 0.2385T2-0.96T + 9.35, r2 = 0.92, P < 0.05, T = impedance detection time in hours. This method showed that the sanitizers PAS and PA were more effective against E. faecium than the other sanitizers. At 30 s, the impedance method recovered about 25 times more cells than the plate count method after vortexing. These data suggest that impedance measurement is the method of choice when evaluating the number of bacterial cells adhered to a surface.

Surface tension measurement of undercooled liquid Ni-based multicomponent alloys

NASA Astrophysics Data System (ADS)

Chang, J.; Wang, H. P.; Zhou, K.; Wei, B.

2012-09-01

The surface tensions of liquid ternary Ni-5%Cu-5%Fe, quaternary Ni-5%Cu-5%Fe-5%Sn and quinary Ni-5%Cu-5%Fe-5%Sn-5%Ge alloys were determined as a function of temperature by the electromagnetic levitation oscillating drop method. The maximum undercoolings obtained in the experiments are 272 (0.15T L), 349 (0.21T L) and 363 K (0.22T L), respectively. For all the three alloys, the surface tension decreases linearly with the rise of temperature. The surface tension values are 1.799, 1.546 and 1.357 N/m at their liquidus temperatures of 1719, 1644 and 1641 K. Their temperature coefficients are -4.972 × 10-4, -5.057 × 10-4 and -5.385 × 10-4 N/m/K. It is revealed that Sn and Ge are much more efficient than Cu and Fe in reducing the surface tension of Ni-based alloys. The addition of Sn can significantly enlarge the maximum undercooling at the same experimental condition. The viscosity of the three undercooled liquid alloys was also derived from the surface tension data.

Assessment of biological chromium among stainless steel and mild steel welders in relation to welding processes.

PubMed

Edmé, J L; Shirali, P; Mereau, M; Sobaszek, A; Boulenguez, C; Diebold, F; Haguenoer, J M

1997-01-01

Air and biological monitoring were used for assessing external and internal chromium exposure among 116 stainless steel welders (SS welders) using manual metal arc (MMA), metal inert gas (MIG) and tungsten inert gas (TIG) welding processes (MMA: n = 57; MIG: n = 37; TIG: n = 22) and 30 mild steel welders (MS welders) using MMA and MIG welding processes (MMA: n = 14; MIG: n = 16). The levels of atmospheric total chromium were evaluated after personal air monitoring. The mean values for the different groups of SS welders were 201 micrograms/m3 (MMA) and 185 micrograms/m3 (MIG), 52 micrograms/m3 (TIG) and for MS welders 8.1 micrograms/m3 (MMA) and 7.3 micrograms/m3 (MIG). The curve of cumulative frequency distribution from biological monitoring among SS welders showed chromium geometric mean concentrations in whole blood of 3.6 micrograms/l (95th percentile = 19.9), in plasma of 3.3 micrograms/l (95th percentile = 21.0) and in urine samples of 6.2 micrograms/l (95th percentile = 58.0). Among MS welders, mean values in whole blood and plasma were rather more scattered (1.8 micrograms/l, 95th percentile = 9.3 and 1.3 micrograms/l, 95th percentile = 8.4, respectively) and in urine the value was 2.4 micrograms/l (95th percentile = 13.3). The analysis of variance of chromium concentrations in plasma previously showed a metal effect (F = 29.7, P < 0.001), a process effect (F = 22.2, P < 0.0001) but no metal-process interaction (F = 1.3, P = 0.25). Concerning urinary chromium concentration, the analysis of variance also showed a metal effect (F = 30, P < 0.0001), a process effect (F = 72, P < 0.0001) as well as a metal-process interaction (F = 13.2, P = 0.0004). Throughout the study we noted any significant differences between smokers and non-smokers among welders. Taking in account the relationships between chromium concentrations in whole, plasma or urine and the different welding process. MMA-SS is definitely different from other processes because the biological values are clearly higher. These higher levels are due to the very significant concentrations of total soluble chromium, mainly hexavalent chromium, in welding fumes.

Weather-Crop Yield Relationships in Drought-Prone Countries of Sub-Saharan Africa Appendix.

DTIC Science & Technology

1979-07-01

commi.- ar A- ::z X: r-’a L< < -t 18 Ei w 4N- nr) % 0I nMMC -D M% - 41 DMr ’ JCI a O0(1a -C, I m n0 e ) I Tr f Tf Ir n% nr - T )W )’ TrI’ rr nr 4)r)e...0.48 0.2 3.25 12.44 8.24 22.02 16.24 21.56 1.0 0.00 0.00 130 0.00 0.87 0.oo 1.24 -.62 12.1; 20.70 30.o3 15.64 13.07 1.64 0.03 131 0.00 0.00 0.20 ..33 7...0.00 I.q1 I.o0 5.:1 10.-6 :t.16 I .75 21.q3 10.41 0.55 0.00 130 0.00 0.00 0.16 0.00 >.16 14.𔃿 2-24 50.72 20.80 20.07 0.00 0.00 131 0.00 0.00 2.10 0.00

Effect of Heat Treatment on the Structure and Properties of Explosion Welded Bimetal Kh20N80 + AD1

NASA Astrophysics Data System (ADS)

Shmorgun, V. G.; Arisova, V. N.; Slautin, O. V.; Taube, A. O.; Bakuntseva, V. M.

2017-05-01

Results of a study of the effect of heat treatment on the microhardness, structure and phase composition of diffusion zone in explosion-welded `refractory nickel alloy Kh20N80 + aluminum alloy AD1' bimetal are presented.

Synthesis, structure, and catalytic performance in cyclooctene epoxidation of a molybdenum oxide/bipyridine hybrid material: {[MoO3(bipy)][MoO3(H2O)]}n.

PubMed

Abrantes, Marta; Amarante, Tatiana R; Antunes, Margarida M; Gago, Sandra; Paz, Filipe A Almeida; Margiolaki, Irene; Rodrigues, Alírio E; Pillinger, Martyn; Valente, Anabela A; Gonçalves, Isabel S

2010-08-02

The reaction of [MoO(2)Cl(2)(bipy)] (1) (bipy = 2,2'-bipyridine) with water in a Teflon-lined stainless steel autoclave (100 degrees C, 19 h), in an open reflux system with oil bath heating (12 h) or in a microwave synthesis system (120 degrees C, 4 h), gave the molybdenum oxide/bipyridine hybrid material {[MoO(3)(bipy)][MoO(3)(H(2)O)]}(n) (2) as a microcrystalline powder in yields of 72-92%. The crystal structure of 2 determined from synchrotron X-ray powder diffraction data is composed of two distinct neutral one-dimensional polymers: an organic-inorganic polymer, [MoO(3)(bipy)](n), and a purely inorganic chain, [MoO(3)(H(2)O)](n), which are interconnected by O-H...O hydrogen bonding interactions. Compound 2 is a moderately active, stable, and selective catalyst for the epoxidation of cis-cyclooctene at 55 degrees C with tert-butylhydroperoxide (tBuOOH, 5.5 M in decane or 70% aqueous) as the oxidant. Biphasic solid-liquid or triphasic solid-organic-aqueous mixtures are formed, and 1,2-epoxycyclooctane is the only reaction product. When n-hexane is employed as a cosolvent and tBuOOH(decane) is the oxidant, the catalytic reaction is heterogeneous in nature, and the solid catalyst can be recycled and reused without a loss of activity. For comparison, the catalytic performance of the precursor 1 was also investigated. The IR spectra of solids recovered after catalysis indicate that 1 transforms into the organic-inorganic polymer [MoO(3)(bipy)] when the oxidant is tBuOOH(decane) and compound 2 when the oxidant is 70% aqueous tBuOOH.

The Syntheses and Structure of the First Vanadium(IV) and Vanadium(V) Binary Azides, V(N3)4, [V(N3)6]2- and [V(N3)6]- (Preprint)

DTIC Science & Technology

2009-11-17

V(N3)3(N3S2)] 2- , [22] have been reported, and no binary vanadium(V) compounds had been known except for VF5, VF6 - and V2O5 . By analogy with...valves. Volatile materials were handled in a Pyrex glass or stainless steel/Teflon-FEP vacuum line. [31] All reaction vessels were passivated with ClF3...successful synthesis of the [V(N3)6] - anion, the only binary vanadium(V) compound known besides VF5, VF6 - and V2O5 . N1’ N8 N9 N1 N2 N3 V N4 N5 N6 N2

Master curve characterization of the fracture toughness behavior in SA508 Gr.4N low alloy steels

NASA Astrophysics Data System (ADS)

Lee, Ki-Hyoung; Kim, Min-Chul; Lee, Bong-Sang; Wee, Dang-Moon

2010-08-01

The fracture toughness properties of the tempered martensitic SA508 Gr.4N Ni-Mo-Cr low alloy steel for reactor pressure vessels were investigated by using the master curve concept. These results were compared to those of the bainitic SA508 Gr.3 Mn-Mo-Ni low alloy steel, which is a commercial RPV material. The fracture toughness tests were conducted by 3-point bending with pre-cracked charpy (PCVN) specimens according to the ASTM E1921-09c standard method. The temperature dependency of the fracture toughness was steeper than those predicted by the standard master curve, while the bainitic SA508 Gr.3 steel fitted well with the standard prediction. In order to properly evaluate the fracture toughness of the Gr.4N steels, the exponential coefficient of the master curve equation was changed and the modified curve was applied to the fracture toughness test results of model alloys that have various chemical compositions. It was found that the modified curve provided a better description for the overall fracture toughness behavior and adequate T0 determination for the tempered martensitic SA508 Gr.4N steels.

In vitro tensile bond strength of adhesive cements to new post materials.

PubMed

O'Keefe, K L; Miller, B H; Powers, J M

2000-01-01

The purpose of this study was to measure the in vitro tensile bond strength of 3 types of adhesive resin cements to stainless steel, titanium, carbon fiber-reinforced resin, and zirconium oxide post materials. Disks of post materials were polished to 600 grit, air abraded, and ultrasonically cleaned. Zirconium oxide bonding surfaces were pretreated with hydrofluoric acid and silanated. Bis-Core, C&B Metabond, and Panavia cements were bonded to the post specimens and placed in a humidor for 24 hours. Post specimens were debonded in tension. Means and standard deviations (n = 5) were analyzed by 2-way analysis of variance. Tukey-Kramer intervals at the 0.05 significance level were calculated. Failure modes were observed. Panavia 21 provided the highest bond strengths for all types of post materials, ranging from 22 MPa (zirconium oxide) to 37 MPa (titanium). C&B Metabond bonded significantly more strongly to stainless steel (27 MPa) and titanium (22 MPa) than to zirconium oxide (7 MPa). Bis-Core results were the lowest, ranging from 16 MPa (stainless steel) to 8 MPa (zirconium oxide). In most cases, bonds to carbon fiber post materials were weaker than to stainless steel and titanium, but stronger than to zirconium oxide. In general, higher bond strengths resulted in a higher percentage of cohesive failures within the cement. Panavia 21 provided the highest bond strengths to all post materials, followed by C&B Metabond. In most cases, adhesive resins had higher bond strengths to stainless steel, titanium, and carbon fiber than to zirconium oxide.

Tribological performance of an H-DLC coating prepared by PECVD

NASA Astrophysics Data System (ADS)

Solis, J.; Zhao, H.; Wang, C.; Verduzco, J. A.; Bueno, A. S.; Neville, A.

2016-10-01

Carbon-based coatings are of wide interest due to their application in machine elements subjected to continuous contact where fluid lubricant films are not permitted. This paper describes the tribological performance under dry conditions of duplex layered H-DLC coating sequentially deposited by microwave excited plasma enhanced chemical vapour deposition on AISI 52100 steel. The architecture of the coating comprised Cr, WC, and DLC (a-C:H) with a total thickness of 2.8 μm and compressive residual stress very close to 1 GPa. Surface hardness was approximately 22 GPa and its reduced elastic modulus around 180 GPa. Scratch tests indicated a well adhered coating achieving a critical load of 80 N. The effect of normal load on the friction and wear behaviours were investigated with steel pins sliding against the actual coating under dry conditions at room temperature (20 ± 2 °C) and 35-50% RH. The results show that coefficient of friction of the coating decreased from 0.21 to 0.13 values with the increase in the applied loads (10-50 N). Specific wear rates of the surface coating also decrease with the increase in the same range of applied loads. Maximum and minimum values were 14 × 10-8 and 5.5 × 10-8 mm-3/N m, respectively. Through Raman spectroscopy and electron microscopy it was confirmed the carbon-carbon contact, due to the tribolayer formation on the wear scars of the coating and pin. In order to further corroborate the experimental observations regarding the graphitisation behaviour, the existing mathematical relationships to determine the graphitisation temperature of the coating/steel contact as well as the flash temperature were used.

Effect of feeding lambs with a tanniferous shrub (rockrose) and a vegetable oil blend on fatty acid composition of meat lipids.

PubMed

Francisco, A; Alves, S P; Portugal, P V; Pires, V M R; Dentinho, M T; Alfaia, C M; Jerónimo, E; Prates, J A M; Santos-Silva, J; Bessa, R J B

2016-12-01

The effects of feeding Cistus ladanifer (Cistus) and a blend of soybean and linseed oil (1 : 2 vol/vol) on fatty acid (FA) composition of lamb meat lipids and messenger RNA (mRNA) expression of desaturase enzymes was assessed. In total, 54 male lambs were randomly assigned to 18 pens and to nine diets, resulting from the combination of three inclusion levels of Cistus (50 v. 100 v. 200 g/kg of dry matter (DM)) and three inclusion levels of oil (0 v. 40 v. 80 g/kg of DM). The forage-to-concentrate ratio of the diets was 1 : 1. Longissimus muscle lipids were extracted, fractionated into neutral (NL) and polar lipid (PL) and FA methyl esters obtained and analyzed by GLC. The expression of genes encoding Δ5, Δ6 and Δ9 desaturases (fatty acid desaturase 1 (FADS1), fatty acid desaturase 2 (FADS2) and stearoyl CoA desaturase (SCD)) was determined. Intramuscular fat, NL and PL contents were not affected by oil or Cistus. Oil supplementation reduced (P<0.05) 16:0, c9-16:1, 17:0, c9-17:1 and c9-18:1 FA and increased (P<0.05) 18:2n-6, 18:3n-3 and the majority of biohydrogenation intermediates in NL. Cistus alone had few effects on FA of NL but interacted with oil (P<0.05) by increasing t10-18:1,t10,t12-18:2,t10,c12-18:2 and t7,c9-18:2. The t10-/t11-18:1 ratio increased with both Cistus and oil levels. The c9, t11-18:2 did not increase (P<0.05) with both oil and Cistus dietary inclusion. Oil reduced c9-16:1, 17:0, c9-17:1,c9-18:1, 20:4n-6, 22:4n-6 and 20:3n-9 proportions in PL, and increased 18:2n-6, 18:3n-3, 20:3n-3 and of most of the biohydrogenation intermediates. The Cistus had only minor effects on FA composition of PL. Cistus resulted in a reduction (P<0.05) of 20:5n-3 and 22:6n-3 in the meat PL. The expression level of SCD mRNA increased (P=0.015) with Cistus level, although a linear relationship with condensed tannins intake (P=0.11) could not be established. FADS1 mRNA expressed levels increased linearly (P=0.019) with condensed tannins intake. In summary, the inclusion of Cistus and oil in 1 : 1 forage-to-concentrate ratio diets resulted in a large increase in t10-18:1 and no increase in c9,t11-18:2 or n-3 long chain poor in polyunsaturated fatty acids in lamb meat.

Familial translocation involving chromosomes 1 and 9 in a patient with Philadelphia-positive CML

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rehman, K.; Rosner, F.; Shanske, A.

1994-09-01

CML has provided a model for understanding the genetic basis of neoplasia. Approximately 5% of Philadelphia-positive patients have a variant chromosome rearrangement. We recently evaluated a patient with a previously unreported simple variant translocation that is part of a familial rearrangement. He had a constitutional translocation, t(1;9)(p21;p22), which was initially identified after his wife had a routine amniocentesis. Case report: K.H. was a 54-year-old male with CML for 4 years. He had been treated until recently with hydroxyurea. An abnormal male karyotype, 46,XY,t(1;9)(q21;p22),t(9;22)(q34;q11) was recorded from an unstimulated blood sample soon after diagnosis. Both translocations involved the same number 9more » homologue resulting in a derivative 9(1pter{r_arrow}1q21::9p22{r_arrow}9q34::22q11{r_arrow}22qter). A recent CT scan of the chest showed a lytic lesion of a rib with associated soft tissue mass in the right costo-vertebral angle. He was hospitalized for progressive pain in the right lower chest and fever, treated for a UTI, required multiple transfusions for declining hemoglobin and platelets and died shortly thereafter. Autopsy revealed widespread chloromas as part of terminal CML. At least 13 complex rearrangements involving chromosomes 1, 9 and 22 are known. Our case represents a unique rearrangement with a familial component and also unique breakpoints for a Philadelphia variant. In line with the current view of cancer as a clonal disorder, perhaps the constitutional translocation contributed to the multi-step nature of the malignant transformation. In fact, a number of cancer-specific breakpoints in both regions of 1p and 9p are involved in the familial translocation.« less

AirBase - A database of 160,000 aerial photos of Greenland 1930-1980s

NASA Astrophysics Data System (ADS)

Korsgaard, Niels; Weng, Willy L.; Kjær, Kurt H.

2017-04-01

Beginning in the 1930s Danish survey agencies and US military organizations conducted large-scale aerial photograph surveys of Greenland for mapping purposes (1), eventuating in the recording of more than 160,000 photographs. Glaciological researchers have used this amazing resource of multi-decadal observations of the Greenlandic cryosphere for many decades (e.g. (2), (3), (4)). In recent years this information has been synthesized with modern remote sensing data resulting in a range of published research and data sets ((5), (6), (7), (8)). Today, the historical aerial photographs are stored at the SDFE (Agency for Data Supply and Effiency), the successor agency for the institutions doing the surveying and mapping of Greenland where the material is accessible to researchers and general public alike. The digitized flightline maps and databases necessary for the creation of this data for this work was made available by the SDFE, and it the past and present work with this database we present here. Based on digitized flight line maps, the database contains geocoded metadata such as recording dates, camera and film roll canister, connecting the database with the analog archive material. Past work concentrated on bulk digitization, while the focus of the current work is to improve positional accuracy, completeness, and refinements for web publication. (1) Nielsen, A., Olsen, J. & Weng, W. L. Grønlands opmåling og kortlægning. Landinspektøren 37 (1995). (2) Weidick A. Frontal variations at Upernaviks Isstrøm in the last 100 years. Medd. fra Dansk Geol. Forening. Vol. 14 (1958. (3) Bauer, A., Baussart, M., Carbonnell, M., Kasser, P. Perroud, P. & Renaud, A. Missions aériennes de reconnaissance au Groenland 1957-1958. Observations aériennes et terrestres, exploitation des photographies aériennes, détermination des vitesses des glaciers vêlant dans Disko Bugt et Umanak Fjord. Meddelelser om Grønland 173(3) (1968a. (4) Rignot, E. Box, J.E., Burgess, E. & Hanna, E. Mass balance of the Greenland ice sheet from 1958 to 2007. Geophys. Res. Lett. (2008. (5) Kjær, K.H., Khan, S.A., Korsgaard, N.J., Wahr, J., Bamber, J.L., Hurkmans, R., van den Broeke, M., Timm, L.H., Kjeldsen, K.K., Bjørk, A.A., Larsen, N.K., Jørgensen, L.T., Færch-Jensen, A. & Willerslev, E. Aerial Photographs Reveal Late-20th-Century Dynamic Ice Loss in Northwestern Greenland. Science 337 (2012). (6) Bjørk, A.A., Kjær, K.H., Korsgaard, N.J., Khan, S.A., Kjeldsen, K.K., Andresen, C.S., Box, J, Larsen, N.K. & Funder, S.V. An aerial view of 80 years of climate-related glacier fluctuations in southeast Greenland. Nat. Geosci. 5 (2012). (7) Kjeldsen, K.K., Korsgaard, N.J., Bjørk, A.A., Khan, S.A., Box, J.E., Funder, S., Larsen, N.K., Bamber, J.L., Colgan, W., van den Broeke, M., Siggaard-Andersen, M.-L., Nuth, C., Schomacker, A., Andresen, C.S., Willerslev, E. & Kjær, K.H. Spatial and temporal distribution of mass loss from the Greenland Ice Sheet since AD 1900. Nature 528 (2015). (8) Korsgaard, N.J., Nuth, C., Khan, S.A., Kjeldsen, K.K., Bjørk, A.A., Schomacker A. & Kjær, K.H. Digital elevation model and orthophotographs of Greenland based on aerial photographs from 1978-1987. Sci. Data 3:160032 (2016).

77 FR 64352 - Notice of Temporary Closure of Public Lands in Custer County, ID

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-19

..., Idaho Potential Capture Site 1 T. 11 N., R. 19 E. Secs. 22, 23, 26, 27, 28, 29, 32, 33 and 34 Potential Capture Site 2 T. 10 N., R. 19 E. Secs. 21, 22, 23, 25, 26, 27 and 35 T. 10 N., R. 20 E. Secs. 29, 30, 31, 32 Potential Capture Site 3 T. 11 N., R. 20 E. Secs. 4, 5, 8, 9, 10, and 17 Potential Capture Site 4...

Effects of temperature on the specific dynamic action of the southern catfish, Silurus meridionalis.

PubMed

Luo, Yiping; Xie, Xiaojun

2008-02-01

Specific dynamic action (SDA), the energy expended on all physiological processes that is associated with meal digestion and assimilation, is strongly affected by temperature. We assessed the effects of temperature on the postprandial metabolic response and calculated SDA of the southern catfish, Silurus meridionalis. The fish was fed with experimental diets at a meal size of 4% body mass, and by using an 8-chamber, continuous-flow respirometer the oxygen consumption rate was determined at a 2 h interval until the postprandial oxygen consumption rate returning to the preprandial level, at four different temperatures. The energy expended on SDA (SDA(E)) were 2.71, 3.07, 3.16, and 3.62 kJ, the SDA(coefficients) (energy expended on SDA quantified as a percentage of the digestible energy content of the meal) were 7.70, 9.44, 10.36, and 11.12%, and the peak metabolic rates (R(peak)) of SDA were 3.48, 4.31, 5.96, and 7.30 mg O2 h(-1), at 17.5, 22.5, 27.5, and 32.5 degrees C respectively. The relationships between those parameters and temperature were: SDA(E)=1.74+0.0559T (n=26, r(2)=0.676), SDA(coefficient)=4.10+0.223T (n=26, r(2)=0.726), and R(peak)=-1.34+0.264T (n=26, r(2)=0.896). The SDA durations showed a slow-fast-slow tendency of decrease with increasing temperature, and were 88.00, 85.71, 67.71, and 66.50 h at 17.5, 22.5, 27.5 and 32.5 degrees C respectively. Two separate peaks appeared during the SDA response at 17.5 degrees C, and it might be due to a rapid startup of the mechanical process with a lag of the biochemical process, which suggested that the peaks of "mechanical component" and "biochemical component" of SDA might be separated when temperature was low enough.

Cast, heat-resistant austenitic stainless steels having reduced alloying element content

DOEpatents

Muralidharan, Govindarajan [Knoxville, TN; Sikka, Vinod Kumar [Oak Ridge, TN; Maziasz, Philip J [Oak Ridge, TN; Pankiw, Roman I [Greensburg, PA

2011-08-23

A cast, austenitic steel composed essentially of, expressed in weight percent of the total composition, about 0.4 to about 0.7 C, about 20 to about 30 Cr, about 20 to about 30 Ni, about 0.5 to about 1 Mn, about 0.6 to about 2 Si, about 0.05 to about 1 Nb, about 0.05 to about 1 W, about 0.05 to about 1.0 Mo, balance Fe, the steel being essentially free of Ti and Co, the steel characterized by at least one microstructural component selected from the group consisting of MC, M.sub.23C.sub.6, and M(C, N).

Cast, heat-resistant austenitic stainless steels having reduced alloying element content

DOEpatents

Muralidharan, Govindarajan [Knoxville, TN; Sikka, Vinod Kumar [Oak Ridge, TN; Maziasz, Philip J [Oak Ridge, TN; Pankiw, Roman I [Greensburg, PA

2010-07-06

A cast, austenitic steel composed essentially of, expressed in weight percent of the total composition, about 0.4 to about 0.7 C, about 20 to about 30 Cr, about 20 to about 30 Ni, about 0.5 to about 1 Mn, about 0.6 to about 2 Si, about 0.05 to about 1 Nb, about 0.05 to about 1 W, about 0.05 to about 1.0 Mo, balance Fe, the steel being essentially free of Ti and Co, the steel characterized by at least one microstructural component selected from the group consisting of MC, M.sub.23C.sub.6, and M(C, N).

PCBs Alter Dopamine Mediated Function in Aging Workers

DTIC Science & Technology

2007-01-01

Thyroid Hormone Function Analysis of serum samples collected for thyroid hormone function (T3, T4, free T3, free T4, and TSH levels) has been conducted by...Thyroid Hormone Measure Mean sem Mean sem TSH 2.06 0.13 2.55 0.36 T4 7.94 0.18 8.72 0.22 Free T4 1.23 0.02 1.22 0.03 T3 133 3.05 122 2.74...FreeT3 5.31 0.08 4.56 0.08 TSH = Thyroid Stimulating Hormone T4 = Thyroxine T3 = 3,5,3-Triidothyronine Investigators Meetings and

Triatoma ryckmani (Hemiptera: Reduviidae) in the epiphyte Tillandsia xerographica (Bromeliaceae) in the semiarid region of Guatemala.

PubMed

Marroquín, Ricardo; Monroy, Carlota; Jaenson, Thomas G T

2004-05-01

For the first time, the reduviid bug Triatoma ryckmani Zeledón and Ponce (Hemiptera; Reduviidae) was recorded to inhabit the epiphyte Tillandsia xerographica Rohweder (Bromeliaceae) in the semiarid region of Guatemala. These bromeliads grow mainly in drought-resistant trees with rough bark such as Pereskia lychnidiflora (Cactaceae). In our study site, we investigated 30 T. xerographica, and 53 specimens of T. ryckmani were found. Most T. ryckmani (68.5%) were unfed. Ants (Formicidae) were the predominant (92.2%) insect taxon in T. xerographica. Other insects such as Blattidae (3.0%), Reduviidae (T. ryckmani: 2.5%), Blaberidae (2.2%), Gryllidae (0.1%), and Acrididae (0.1%) were recorded in the bromeliads. T. xerographica is illegally commercialized without previous inspection. This may cause accidental introduction of T. ryckmani to houses and to other countries.

Increasing phosphorus concentration in the extraradical hyphae of Rhizophagus irregularis DAOM 197198 leads to a concomitant increase in metal minerals.

PubMed

Zhang, Lin; Jiang, Caiyun; Zhou, Jiachao; Declerck, Stéphane; Tian, Changyan; Feng, Gu

2016-11-01

Plants associated with arbuscular mycorrhizal fungi (AMF) acquire phosphorus via roots and extraradical hyphae. How soil P level affects P accumulation within hyphae and how P in hyphae influences the accumulation of metal minerals remains little explored. A bi-compartmented in vitro cultivation system separating a root compartment (RC), containing a Ri T-DNA transformed carrot root associated to the AMF Rhizophagus irregularis DAOM 197198, from a hyphal compartment (HC), containing only the extraradical hyphae, was used. The HC contained a liquid growth medium (i.e., the modified Strullu-Romand medium containing P in the form of KH 2 PO 4 ) without (0 μM) or adjusted to 35, 100, and 700 μM of KH 2 PO 4 . The accumulation of P and metal minerals (Ca, Mg, K, Na, Fe, Cu, Mn) within extraradical hyphae and AMF-colonized roots, and the expression of the phosphate transporter gene GintPT were assessed. The expression of GintPT in the extraradical hyphae did not differ in absence of KH 2 PO 4 or in presence of 35 and 100 μM KH 2 PO 4 in the HC but was markedly reduced in presence of 700 μM KH 2 PO 4 . Hyphal P concentration was significantly lowest in absence of KH 2 PO 4 , intermediate at 35 and 100 μM KH 2 PO 4 and significantly highest in presence of 700 μM KH 2 PO 4 in the HC. The concentrations of K, Mg, and Na were positively associated with the concentration of P in the extraradical hyphae developing in the HC. Similarly, P concentration in extraradical hyphae in the HC was related to P concentration in the growth medium and influenced the concentration of K, Mg, and Na. The accumulation of the metal mineral K, Mg, and Na in the extraradical hyphae developing in the HC was possibly related to their function in neutralizing the negative charges of PolyP accumulated in the hyphae.

Study on underclad cracking in nuclear reactor vessel steels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Horiya, T.; Takeda, T.; Yamato, K.

1985-02-01

Susceptibility to underclad cracking in nuclear reactor vessel steels, such as SA533 Grade B Class 1 and SA508 Class 2, was studied in detail. A convenient simulation test method using simulated HAZ specimens of small size has been developed for quantitative evaluation of susceptibility to underclad cracks. The method can predict precisely the cracking behavior in weldments of steels with relative low crack susceptibility. The effect of chemical compositions on susceptibility to the cracking was examined systematically using the developed simulation test method and the following index was obtained from the test results: U = 20(V) + 7(C) + 4(Mo)more » + (Cr) + (Cu) - 0.5(Mn) + 1.5 log(X) X = Al . . . Al/2N less than or equal to 1 X = 2N . . . Al/2N > 1 It was confirmed that the new index (U) is useful for the prediction of crack susceptibility of the nuclear vessel steels; i.e., no crack initiation is detected in weldments in the roller bend test for steels having U value below 0.90.« less

Effect of Continuous Galvanizing Heat Treatments on the Microstructure and Mechanical Properties of High Al-Low Si Transformation Induced Plasticity Steels

NASA Astrophysics Data System (ADS)

Bellhouse, E. M.; McDermid, J. R.

2010-02-01

Heat treatments were performed using an isothermal bainitic transformation (IBT) temperature compatible with continuous hot-dip galvanizing on two high Al-low Si transformation induced plasticity (TRIP)-assisted steels. Both steels had 0.2 wt pct C and 1.5 wt pct Mn; one had 1.5 wt pct Al and the other had 1 wt pct Al and 0.5 wt pct Si. Two different intercritical annealing (IA) temperatures were used, resulting in intercritical microstructures of 50 pct ferrite (α)-50 pct austenite (γ) and 65 pct α-35 pct γ. Using the IBT temperature of 465 °C, five IBT times were tested: 4, 30, 60, 90, and 120 seconds. Increasing the IBT time resulted in a decrease in the ultimate tensile strength (UTS) and an increase in the uniform elongation, yield strength, and yield point elongation. The uniform elongation was higher when using the 50 pct α-50 pct γ IA temperature when compared to the 65 pct α-35 pct γ IA temperature. The best combinations of strength and ductility and their corresponding heat treatments were as follows: a tensile strength of 895 MPa and uniform elongation of 0.26 for the 1.5 pct Al TRIP steel at the 50 pct γ IA temperature and 90-second IBT time; a tensile strength of 880 MPa and uniform elongation of 0.27 for the 1.5 pct Al TRIP steel at the 50 pct γ IA temperature and 120-second IBT time; and a tensile strength of 1009 MPa and uniform elongation of 0.22 for the 1 pct Al-0.5 pct Si TRIP steel at the 50 pct γ IA temperature and 120-second IBT time.

High trapped fields in bulk YBCO superconductors

NASA Astrophysics Data System (ADS)

Fuchs, Günter; Gruss, Stefan; Krabbes, Gernot; Schätzle, Peter; Verges, Peter; Müller, Karl-Hartmut; Fink, Jörg; Schultz, Ludwig

The trapped field properties of bulk melt-textured YBCO material were investigated at different temperatures. In the temperature range of liquid nitrogen, maximum trapped fields of 1.1 T were found at 77 K by doping of YBCO with small amounts of zinc. The improved pinning of zinc-doped YBa2Cu3O7-x (YBCO) results in a pronounced peak effect in the field dependence of the critical current density. the trapped field at lower temperatures increases due to the increasing critical current density, however, at temperatures around 50 K cracking of the material is observed which is exposed to considerably tensile stresses due to Lorentz forces. Very high trapped fields up to 14.4 T were achieved at 22.5 K for a YBCO disk pair by the addition of silver improving the tensile strength of YBCO and by using a bandage made of a steel tube. The steel tube produces a compressive stress on YBCO after cooling down from 300 K to the measuring temperature, which is due to the higher coeeficient of thermal expansion of steel compared with that of YBCO in the a,b plane. The application of superconducting permanent magnets with trapped fields of 10 T and more in superconducting bearings would allow to obtain very high levitation pressures up to 2500 N/cm2 which is two orders of magnitude higher than the levitation pressure achievable in superconducting bearings with conventional permanent magnets. The most important problem for the application of superconducting permanent magnets is the magnetizing procedure of the YBCO material. Results of magnetizing YBCO disks by using of pulsed magnetic fields will be presented.

Laccase production by Coriolopsis caperata RCK2011: Optimization under solid state fermentation by Taguchi DOE methodology

PubMed Central

Nandal, Preeti; Ravella, Sreenivas Rao; Kuhad, Ramesh Chander

2013-01-01

Laccase production by Coriolopsis caperata RCK2011 under solid state fermentation was optimized following Taguchi design of experiment. An orthogonal array layout of L18 (21 × 37) was constructed using Qualitek-4 software with eight most influensive factors on laccase production. At individual level pH contributed higher influence, whereas, corn steep liquor (CSL) accounted for more than 50% of the severity index with biotin and KH2PO4 at the interactive level. The optimum conditions derived were; temperature 30°C, pH 5.0, wheat bran 5.0 g, inoculum size 0.5 ml (fungal cell mass = 0.015 g dry wt.), biotin 0.5% w/v, KH2PO4 0.013% w/v, CSL 0.1% v/v and 0.5 mM xylidine as an inducer. The validation experiments using optimized conditions confirmed an improvement in enzyme production by 58.01%. The laccase production to the level of 1623.55 Ugds−1 indicates that the fungus C. caperata RCK2011 has the commercial potential for laccase. PMID:23463372

Investigation of a Multifrequency Reconfigurable Phased Array Antenna

DTIC Science & Technology

1991-05-01

236 2.04 37.5 194 487 1639 22 05 2.ř 4A 2.37 I4.0 2.00 26.2 95 385 1.73 376 1497 23 -01 102 4.4 2.41 131 2.12 25.7 1.97 380 17 37.3 1497 24 0.1 313 46...CONTROL VOLTAGE - --- -30 I8 3I i 2 1 4 4 to I 10 At FREQUENCY C o 9Gift Figure 3-8. MMIC Specification 3-9 Report 6693 0 , coc D0C U, m wC, fc N 14 N...I I I -f 1-:t- 14 tj I IV t-r: It tU t- -11 H ill Afff Mill I I- -all tjLu 4A ff-- _mf 41 Mil Aill &U I 11i 7 > I till r4t I 11-11 It fl-lH f

Effects of self-ligating and conventional brackets on halitosis and periodontal conditions.

PubMed

Kaygisiz, Emine; Uzuner, Fatma Deniz; Yuksel, Sema; Taner, Levent; Çulhaoğlu, Rana; Sezgin, Yasemin; Ateş, Can

2015-05-01

To evaluate the effects of fixed orthodontic treatment with steel-ligated conventional brackets and self-ligating brackets on halitosis and periodontal health. Sixty patients, at the permanent dentition stage aged 12 to 18 years, who had Angle Class I malocclusion with mild-to-moderate crowding were randomly selected. Inclusion criteria were nonsmokers, without systematic disease, and no use of antibiotics and oral mouth rinses during the 2-month period before the study. The patients were subdivided into three groups randomly: the group treated with conventional brackets (group 1, n  =  20) ligated with steel ligature wires, the group treated with self-ligating brackets (group 2, n  =  20), and the control group (group 3, n  =  20). The periodontal records were obtained 1 week before bonding (T1), immediately before bonding (T2), 1 week after bonding (T3), 4 weeks after bonding (T4), and 8 weeks after bonding (T5). Measurements of the control group were repeated within the same periods. The volatile sulfur components determining halitosis were measured with the Halimeter at T2, T3, T4, and T5. A two-way repeated measures of analysis of variance (ANOVA) was used to compare the groups statistically. No statistically significant group × time interactions were found for plaque index, gingival index, pocket depth, bleeding on probing, and halitosis, which means three independent groups change like each other by time. The risk of tongue coating index (TCI) being 2 was 10.2 times higher at T1 than at T5 (P < .001). Therefore, the probability of higher TCI was decreased by time in all groups. The self-ligating brackets do not have an advantage over conventional brackets with respect to periodontal status and halitosis.

Thyroid and sympathetic influences on plasma leptin in hypothyroidism and hyperthyroidism.

PubMed

Pinkney, J H; Goodrick, S J; Katz, J R; Johnson, A B; Lightman, S L; Coppack, S W; Medbak, S; Mohamed-Ali, V

2000-06-01

To determine the dependence of plasma leptin concentrations upon circulating noradrenaline (NA) and thyroid hormones (TH) in humans. Cross-sectional study in 40 newly diagnosed untreated patients with primary thyroid disease, and 69 lean and obese euthyroid control subjects. Plasma leptin, NA, free T3 (fT3) and TSH in the fasting state. Anthropometry and % body fat (electrical bioimpedance). Leptin levels were highest in 37 obese euthyroid and 22 hypothyroid (median [interquartiles]31.5 [19.0- 48.0], 19.2 [11.5-31.5] ng ml(-1)), and lowest in 32 lean euthyroid and 18 hyperthyroid subjects (6.6 [3.9-14.4], 8.9 [5.5-11.1]; ANOVA, P< 0.0001). Plasma NA was similar in all groups (P= n.s.). In obese controls, TSH correlated with % body fat and leptin (r= 0.67, r= 0.61; P< 0.001). Treatment of hypothyroidism (n= 10) with T4 reduced leptin from 20.8 [11.8-31.6] to 12.9[4.6-21.2] (P= 0.005) with no change in BMI. Thyroid status modifies leptin secretion independently of adiposity and NA. The data suggest leptin-thyroid interactions at hypothalamic and adipocyte level.

Biophysics of cochlear implant/MRI interactions emphasizing bone biomechanical properties.

PubMed

Sonnenburg, Robert E; Wackym, Phillip A; Yoganandan, Narayan; Firszt, Jill B; Prost, Robert W; Pintar, Frank A

2002-10-01

The forces exerted during a 1.5-Tesla MRI evaluation on the internal magnet of a cochlear implant (CI) raise concern about the safety for CI recipients. This study determines the magnitude of force required to fracture the floor of a CI receiver bed. Recessed CI beds were drilled to maximum uniform thinness into formalin-fixed and fresh-frozen human calvaria specimens. A Med-El stainless steel CI template mounted to the piston of an electrohydraulic testing device was used to fracture the floor of the implant beds. Force and displacement were measured as a function of time using a digital data acquisition system. Mean force to first failure, displacement to first failure, and minimum thickness, respectively, were: group 1 (formalin-fixed, 0.3-0.4-mm thick [n = 22]), 34.08 N (8.21-59.64 N, standard deviation [SD] 15.41 N), 1.09 mm (0.40-2.16 mm, SD 0.51 mm), 0.36 mm (0.3-0.4 mm, SD 0.05 mm); group 2 (formalin-fixed, 0.5-0.9 mm thick [n = 21]), 52.82 N (20.28-135.53 N, SD 25.29 N), 1.08 mm (0.50-2.28 mm, SD 0.47 mm), 0.58 mm (0.5-0.9 mm, SD 0.12 mm); group 3 (fresh-frozen [n = 9]), 134.13 N (86.44-190.70 N, SD 34.92 N), 1.96 mm (1.47-2.46 mm, SD 0.35 mm), 0.42 mm (0.3-0.6 mm, SD 0.11 mm). The mean magnitude of force required to fracture the floor of a CI bed is significantly greater than those that are generated when a Med-El Combi 40+, CII Bionic Ear CI, or Nucleus Contour CI is placed into a 1.5-Tesla MRI unit.

Effects of Non-metallic Inclusions on Hot Ductility of High Manganese TWIP Steels Containing Different Aluminum Contents

NASA Astrophysics Data System (ADS)

Wang, Yu-Nan; Yang, Jian; Wang, Rui-Zhi; Xin, Xiu-Ling; Xu, Long-Yun

2016-06-01

The characteristics of inclusions in Fe-16Mn- xAl-0.6C ( x = 0.002, 0.033, 0.54, 2.10 mass pct) steels have been investigated and their effects on hot ductility of the high manganese TWIP steels have been discussed. Ductility is very poor in the steel containing 0.54 mass pct aluminum, which is lower than 20 pct in the temperature range of 873 K to 1473 K (600 °C to 1200 °C). For the steels containing 0.002 and 2.10 mass pct aluminum, ductility is higher than 40 pct in the same temperature range. The hot ductility of steel containing 0.033 mass pct aluminum is higher than 30 pct throughout the temperature range under examination. With increasing aluminum content, the main inclusions in the steels change along the route of MnO/(MnO + MnS) → MnS/(Al2O3 + MnS) → AlN/(Al2O3 + MnS)/(MgAl2O4 + MnS) → AlN. The thermodynamic results of inclusion types calculated with FactSage software are in agreement with the experimental observation results. The inclusions in the steels containing 0.002 mass pct aluminum do not deteriorate the hot ductility. MnS inclusions whose average size, number density, and volume ratio are 1.12 μm, 15.62 mm-2, and 2.51 × 10-6 in the steel containing 0.033 mass pct aluminum reduce the ductility. In the steel containing 0.54 mass pct aluminum, AlN inclusions whose average size, number density, and volume ratio are 0.878 μm, 16.28 mm-2 and 2.82 × 10-6 can precipitate at the austenite grain boundaries, prevent dynamic recrystallization and deteriorate the hot ductility. On the contrary, in the steel containing 2.10 mass pct aluminum, the average size, number density and volume ratio of AlN inclusions change to 2.418 μm, 35.95 mm-2, and 2.55 × 10-5. They precipitate in the matrix, which do not inhibit dynamic recrystallization and thereby do not lead to poor hot ductility.

Application of laser in seam welding of dissimilar steel to aluminium joints for thick structural components

NASA Astrophysics Data System (ADS)

Meco, S.; Pardal, G.; Ganguly, S.; Williams, S.; McPherson, N.

2015-04-01

Laser welding-brazing technique, using a continuous wave (CW) fibre laser with 8000 W of maximum power, was applied in conduction mode to join 2 mm thick steel (XF350) to 6 mm thick aluminium (AA5083-H22), in a lap joint configuration with steel on the top. The steel surface was irradiated by the laser and the heat was conducted through the steel plate to the steel-aluminium interface, where the aluminium melts and wets the steel surface. The welded samples were defect free and the weld micrographs revealed presence of a brittle intermetallic compounds (IMC) layer resulting from reaction of Fe and Al atoms. Energy Dispersive Spectroscopy (EDS) analysis indicated the stoichiometry of the IMC as Fe2Al5 and FeAl3, the former with maximum microhardness measured of 1145 HV 0.025/10. The IMC layer thickness varied between 4 to 21 μm depending upon the laser processing parameters. The IMC layer showed an exponential growth pattern with the applied specific point energy (Esp) at a constant power density (PD). Higher PD values accelerate the IMC layer growth. The mechanical shear strength showed a narrow band of variation in all the samples (with the maximum value registered at 31.3 kN), with a marginal increase in the applied Esp. This could be explained by the fact that increasing the Esp results into an increase in the wetting and thereby the bonded area in the steel-aluminium interface.

Steel tanks T5 and T4 with overhead pipeline between. Redwood ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Steel tanks T5 and T4 with overhead pipeline between. Redwood tanks seen in background - Hawaii Volcanoes National Park Water Collection System, Hawaii Volcanoes National Park, Volcano, Hawaii County, HI

Mean Conditions and Turbulence Statistics at Vandenberg AFB, California,

DTIC Science & Technology

1984-11-01

2NN M N NN ’CN N NN N4 I’~tJN NN NIJN I pIi JN’ W’N NCJ’ ViNNCJ m I’N’(I N’N CJ N N N C’ 0 ’o CD22 REPRODUCEDU AT CG0VFRr4?A.FJ1 uvrF 11.4 PiJ0t’ N

Xanthan gum production using jackfruit-seed-powder-based medium: optimization and characterization.

PubMed

Felicia Katherine, R; Muthukumaran, C; Sharmila, G; Manoj Kumar, N; Tamilarasan, K; Jaiganesh, R

2017-08-01

Xanthan gum (XG) production by Xanthomonas campestris NCIM 2961 using jackfruit seed powder (JSP) as a novel substrate was reported. Central composite design (CCD) of response surface method (RSM) was used to evaluate the linear and interaction effects of five medium variables (JSP, peptone, citric acid, K 2 HPO 4 and KH 2 PO 4 ) for XG production. Maximum XG production (51.62 g/L) was observed at the optimum level of JSP (4 g/L), peptone (0.93 g/L), citric acid (0.26 g/L), K 2 HPO 4 (1.29 g/L) and KH 2 PO 4 (0.5 g/L). K 2 HPO 4 and KH 2 PO 4 were found as significant medium components, which served as buffering agents as well as nutrients for X. campestris growth. The obtained biopolymer was characterized as XG by XRD and FTIR analysis. Results of this study revealed that JSP was found to be a suitable low cost substrate for XG production.

Association of the protein tyrosine phosphatase non-receptor 22 polymorphism (PTPN22) with endometriosis: a meta-analysis.

PubMed

Pabalan, Noel; Jarjanazi, Hamdi; Christofolini, Denise Maria; Bianco, Bianca; Barbosa, Caio Parente

2017-01-01

To evaluate PTPN22 C1858T polymorphism and the risk of endometriosis. A meta-analysis of 10 published case-control studies (from four articles), with a total sample of 971 cases and 1,181 controls, was performed. We estimated risk (odds ratio and 95% confidence intervals) of endometriosis associations with the C1858T polymorphism. A significant increased risk in all genetic models of the variant T allele with endometriosis (odds ratio: 3.14-5.55; p<0.00001-0.002) was found. The analysis without the study whose controls deviated from the Hardy-Weinberg equilibrium exacerbated these effects in the homozygous and recessive models (odds ratio: 7.19-9.45; p<0.00001-0.0002). In the Italian subgroup, a significant risk association was found in the homozygous and recessive models (odds ratio: 8.72-11.12; p=0.002). The associations observed between PTPN22 (C1858T) and the risk of endometriosis suggest this polymorphism might be a useful susceptibility marker for this disease. Avaliar o polimorfismo PTPN22 C1858T e o risco de endometriose. Foi realizada uma metanálise de 10 estudos caso-controle publicados (a partir de quatro artigos), com uma amostra total de 971 casos e 1.181 controles. O risco da associação da endometriose com o polimorfismo C1858T foi estimado em razão de chance e intervalo de confiança de 95%. Observou-se um aumento de risco significativo em todos os modelos genéticos com o alelo variante T e a endometriose (razão de chance: 3,14-5,55; p<0,00001-0,002). A análise sem incluir o estudo, em que os controles não estavam em equilíbrio de Hardy-Weinberg, mostrou aumento significativo nos modelos homozigotos e recessivos (razão de chance: 7,19-9,45; p<0,00001-0,0002). No subgrupo italiano, uma associação significativa foi encontrada considerando os modelos homozigoto e recessivo (razão de chance: 8,72-11,12; p=0,002). As associações observadas entre PTPN22 (C1858T) e o risco de endometriose sugerem que este polimorfismo pode ser um marcador de suscetibilidade para a endometriose.

Effect of heat treatment on the crystal structure of deformed samples of chromium-manganese steel

NASA Astrophysics Data System (ADS)

Chezganov, D. S.; Chikova, O. A.; Borovykh, M. A.

2017-09-01

Results of studying microstructures and the crystal structure of samples of 35KhGF steel (0.31-0.38 wt % C, 0.17-0.37 wt % Si, 0.95-1.25 wt % Mn, 1.0-1.3 wt % Cr, 0.06-0.12 wt % V, and the remainder was Fe) have been presented. The samples have been selected from hot-rolled pipes subjected to different heat treatments. A study has been carried out in order to explain the choice of the heat-treatment regime based on determining the structure-properties relationship that provides an increase in the corrosion resistance of pipes to the effect of hydrocarbons. Methods of the energy-dispersive X-ray spectroscopy (EDS) and electron backscatter diffraction (EBSD) have been used. In the microstructure of samples, oxide inclusions and discontinuities with sizes of 1-50 μm that presumably consist of the scale were detected. The ferrite grain size and the orientations of crystals were determined; the data on the local mechanical stresses in the Taylor orientation- factor maps were obtained. The grain refinement; the increase in the fraction of the low-angle boundaries; and the decrease in the local mechanical stresses and, therefore, the highest corrosion resistance to the effect of hydrocarbons is achieved by normalizing at 910°C.

Environmental Consequences of Nanotechnologies: Nanoparticle Dispersion in Aqueous Media: SOP-T-1

DTIC Science & Technology

2015-02-01

containing ice • Bath sonicator • Weighing dish (aluminum) • Stainless steel spatula • Analytical balance • Lab jack for lifting sample • Volumetric...balance and an aluminum dish, weigh an adequate mass of dry powder under a fume hood to achieve the desired concentration into ultrapure water (<T>, <R...0.025 0.5 0.05 1 0.5 10 1 20 2. Add ultra-pure water in a glass beaker with NP powder to /flask under fume hood (<T>, <R>). 3. Degas the bath

A Preliminary Investigation on the Destruction of Solid-Propellant Rocket Motors by Impact from Small Particles

NASA Technical Reports Server (NTRS)

Carter, David J., Jr.

1960-01-01

An investigation was conducted to determine whether solid-propellant rocket motors could be ignited and destroyed by small-particle impacts at particle velocities up to a approximately 10,940 feet per second. Spheres ranging from 1/16 to 7/32 inch in diameter were fired into simulated rocket motors containing T-22 propellant over a range of ambient pressures from sea level to 0.12 inch of mercury absolute. Simulated cases of stainless steel, aluminum alloy, and laminated Fiberglas varied in thickness from 1/50 to 1/8 inch. Within the scope of this investigation, it was found that ignition and explosive destruction of simulated steel-case rocket motors could result from impacts by steel spheres at the lowest attainable pressure.

[Biomechanical properties of bioabsorbable cannulated screws for surgical fixation of dislocated epiphysiolysis capitis femoris].

PubMed

Kröber, M W; Rovinsky, D; Lotz, J; Carstens, C; Otsuka, N Y

2002-06-01

Bioabsorbable materials are well suited for fixation of slipped capital femoral epiphysis (SCFE) as they are resorbable, compatible with magnetic resonance imaging, and well tolerated by the pediatric population. We compared cannulated 4.5-mm bioabsorbable screws made of self-reinforced polylevolactic acid (SR-PLLA) to cannulated 4.5-mm steel and titanium screws for their resistance to shear stress and ability to generate compression in a polyurethane foam model of SCFE fixation. The maximum shear stress resisted by the three screw types was similar (SR-PLLA 371 +/- 146, steel 442 +/- 43, titanium 470 +/- 91 MPa, NS). The maximum compression generated by both the SR-PLLA screw (68.5 +/- 3.3 N) and the steel screw (63.3 +/- 5.9 N) was greater than that for the titanium screw (3.0 +/- 1.4 N, p < 0.05). These data suggest that cannulated SR-PLLA screws have sufficient biomechanical strength to be used in the treatment of SCFE.

Vance AFB, Oklahoma. Revised Uniform Summary of Surface Weather Observations (RUSSWO). Parts A-F.

DTIC Science & Technology

1982-12-02

w. -AL Lr ?LO’~ hH o,.T SURFACE WINDS 2 .. ?. SEPVIC/-AC PERCENTAGE FREQUENCY OF WIND DIRECTION AND SPEED (FROM HOURLY OBSERVATIONS... Jb A 4. AL CL TL0- A’i 2i ~CEILING VERSUS VISIBILITY PE ;CE N7AGE :EO, ;ENC Y 0(1 OCU RE’,(jE 1 .-- "J ;R3M H0BY BSR ,A- ONS ., 7 s 6 7 . -5. 󈨐. . 6...15 16 17 1819. 20-21 -. 22 23.24-25 26. 27-2 2.9 30 3 D.- .S. D, 8,11 W,, BJb D- P.... / /Z 5 B 01 0 fl--.., (.) Z.. i-- N.. Ob.. .... N.. .1 . 4th

Heat-Resistant Alloys for Ordnance Materiel and Aircraft and Naval Engine Parts (N-102): Part 1 - Heat Resistant Alloys of the 21%Cr:9%Ni Type

DTIC Science & Technology

1945-06-29

10.555Ni Alloy 22 Sigma and Ferrite In 22.3#r:7.7*Ni Alloy 23 Ferrite Mosaic In 22.3#r:7.7#Ni Alloy 24 Precipitated Carbides In 21.2*Cr:8.7*Ni... ferritic steels and heat resistant cast irons are widely applied. Where plasticity is essential,steels must be used. The irons exhibit some...ductility above 900°F, but they are seldom able to survive sudden thermal or mechanical stresses that exceed their elastic strength. Ferritic steels, of

Arsenic-Rich Polyarsenides Stabilized by Cp*Fe Fragments.

PubMed

Schmidt, Monika; Konieczny, David; Peresypkina, Eugenia V; Virovets, Alexander V; Balázs, Gabor; Bodensteiner, Michael; Riedlberger, Felix; Krauss, Hannes; Scheer, Manfred

2017-06-12

The redox chemistry of [Cp*Fe(η 5 -As 5 )] (1, Cp*=η 5 -C 5 Me 5 ) has been investigated by cyclic voltammetry, revealing a redox behavior similar to that of its lighter congener [Cp*Fe(η 5 -P 5 )]. However, the subsequent chemical reduction of 1 by KH led to the formation of a mixture of novel As n scaffolds with n up to 18 that are stabilized only by [Cp*Fe] fragments. These include the arsenic-poor triple-decker complex [K(dme) 2 ][{Cp*Fe(μ,η 2:2 -As 2 )} 2 ] (2) and the arsenic-rich complexes [K(dme) 3 ] 2 [(Cp*Fe) 2 (μ,η 4:4 -As 10 )] (3), [K(dme) 2 ] 2 [(Cp*Fe) 2 (μ,η 2:2:2:2 -As 14 )] (4), and [K(dme) 3 ] 2 [(Cp*Fe) 4 (μ 4 ,η 4:3:3:2:2:1:1 -As 18 )] (5). Compound 4 and the polyarsenide complex 5 are the largest anionic As n ligand complexes reported thus far. Complexes 2-5 were characterized by single-crystal X-ray diffraction, 1 H NMR spectroscopy, EPR spectroscopy (2), and mass spectrometry. Furthermore, DFT calculations showed that the intermediate [Cp*Fe(η 5 -As 5 )] - , which is presumably formed first, undergoes fast dimerization to the dianion [(Cp*Fe) 2 (μ,η 4:4 -As 10 )] 2- . © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Kub5-Hera, the human Rtt103 homolog, plays dual functional roles in transcription termination and DNA repair

PubMed Central

Morales, Julio C.; Richard, Patricia; Rommel, Amy; Fattah, Farjana J.; Motea, Edward A.; Patidar, Praveen L.; Xiao, Ling; Leskov, Konstantin; Wu, Shwu-Yuan; Hittelman, Walter N.; Chiang, Cheng-Ming; Manley, James L.; Boothman, David A.

2014-01-01

Functions of Kub5-Hera (In Greek Mythology Hera controlled Artemis) (K-H), the human homolog of the yeast transcription termination factor Rtt103, remain undefined. Here, we show that K-H has functions in both transcription termination and DNA double-strand break (DSB) repair. K-H forms distinct protein complexes with factors that repair DSBs (e.g. Ku70, Ku86, Artemis) and terminate transcription (e.g. RNA polymerase II). K-H loss resulted in increased basal R-loop levels, DSBs, activated DNA-damage responses and enhanced genomic instability. Significantly lowered Artemis protein levels were detected in K-H knockdown cells, which were restored with specific K-H cDNA re-expression. K-H deficient cells were hypersensitive to cytotoxic agents that induce DSBs, unable to reseal complex DSB ends, and showed significantly delayed γ-H2AX and 53BP1 repair-related foci regression. Artemis re-expression in K-H-deficient cells restored DNA-repair function and resistance to DSB-inducing agents. However, R loops persisted consistent with dual roles of K-H in transcription termination and DSB repair. PMID:24589584

Kub5-Hera, the human Rtt103 homolog, plays dual functional roles in transcription termination and DNA repair.

PubMed

Morales, Julio C; Richard, Patricia; Rommel, Amy; Fattah, Farjana J; Motea, Edward A; Patidar, Praveen L; Xiao, Ling; Leskov, Konstantin; Wu, Shwu-Yuan; Hittelman, Walter N; Chiang, Cheng-Ming; Manley, James L; Boothman, David A

2014-04-01

Functions of Kub5-Hera (In Greek Mythology Hera controlled Artemis) (K-H), the human homolog of the yeast transcription termination factor Rtt103, remain undefined. Here, we show that K-H has functions in both transcription termination and DNA double-strand break (DSB) repair. K-H forms distinct protein complexes with factors that repair DSBs (e.g. Ku70, Ku86, Artemis) and terminate transcription (e.g. RNA polymerase II). K-H loss resulted in increased basal R-loop levels, DSBs, activated DNA-damage responses and enhanced genomic instability. Significantly lowered Artemis protein levels were detected in K-H knockdown cells, which were restored with specific K-H cDNA re-expression. K-H deficient cells were hypersensitive to cytotoxic agents that induce DSBs, unable to reseal complex DSB ends, and showed significantly delayed γ-H2AX and 53BP1 repair-related foci regression. Artemis re-expression in K-H-deficient cells restored DNA-repair function and resistance to DSB-inducing agents. However, R loops persisted consistent with dual roles of K-H in transcription termination and DSB repair.

Demonstration and Validation of Stainless Steel Materials for Critical Above Grade Piping in Highly Corrosive Locations

DTIC Science & Technology

2017-05-01

Protecting And Bonding Reinforcing Steel In Cement -Based Composites, Corrosion 2009, Atlanta, GA, 22-26 March 2009. 7. Hock, V., O. Marshall, S...ER D C/ CE RL T R- 17 -1 3 DoD Corrosion Prevention and Control Program Demonstration and Validation of Stainless Steel Materials for...ERDC/CERL TR-17-13 May 2017 Demonstration and Validation of Stainless Steel Materials for Critical Above-Grade Piping in Highly Corrosive

Kinetics of austenite-pearlite transformation in eutectoid carbon steel

NASA Astrophysics Data System (ADS)

Hawbolt, E. B.; Chau, B.; Brimacombe, J. K.

1983-09-01

The kinetics of the austenite-to-pearlite transformation have been measured under isothermal and continuous-cooling conditions on a eutectoid carbon (1080) steel using a diametral dilatometric technique. The isothermal transformation kinetics have been analyzed in terms of the Avrami Equation containing the two parameters n and b; the initiation of transformation was characterized by an empirically determined transformation-start time (tAv). The parameter n was found to be nearly constant; and neither n nor b was dependent on the cooling rate between T A1 and the test temperature. Continuous-cooling tests were performed with cooling rates ranging from 7.5 to 108 °C per second, and the initiation of transformation was determined. Comparison of this transformation-start time for different cooling rates with the measured slow cooling of a test coupon immersed in a salt bath indicates that, particularly at lower temperatures, the transformation in the traditional T-T-T test specimen may not be isothermal. The additivity rule was found to predict accurately the time taken, relative to tAv, to reach a given fraction of austenite transformed, even though there is some question that the isokinetic condition was met above 660 °C. However, the additivity rule does not hold for the pretransformation or incubation period, as originally proposed by Scheil, and seriously overestimates the incubation time. Application of the additivity rule to the prediction of transformation-finish time, based on transformation start at TA1, also leads to overestimates, but these are less serious. The isothermal parameters— n ( T), b ( T), and tAv ( T)—have been used to predict continuous-cooling transformation kinetics which are in close agreement with measurements at four cooling rates ranging from 7.5 to 64 °C per second.

The nature of nano-sized precipitates in ferritic/martensitic steel P92 produced by thermomechanical treatment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shen, Yinzhong, E-mail: shenyz@sjtu.edu.cn

Thermomechanical treatment (TMT) can effectively improve the mechanical properties of high-Cr ferritic/martensitic (F/M) steels, which has been mainly attributed to a dense dispersion of nano-sized precipitates. Precipitate phases in high-Cr F/M steels produced by TMT require further investigations. Precipitates in commercial F/M steel P92 produced by a TMT process, warm-rolled at 650 °C plus tempered at 650 °C for 1 h, were investigated by transmission electron microscopy. Nano-sized precipitates with a high number density in the steel after the TMT were found to be Cr-rich M{sub 2}(C,N) carbonitride, rather than MX or M{sub 23}C{sub 6} phase. The M{sub 2}(C,N) carbonitridemore » has a hexagonal lattice with the lattice parameters about a/c = 0.299/0.463 nm. These M{sub 2}(C,N) carbonitrides with a typical composition of (Cr{sub 0.85}V{sub 0.06}Fe{sub 0.06}Mo{sub 0.03}){sub 2}(C,N) have an average diameter smaller than 30 nm, and mainly distribute on dislocations and at the boundaries of equiaxed ferrite grains in the TMT steel. The TMT process inhibits the precipitation of M{sub 23}C{sub 6} and M{sub 5}C{sub 2} phases. Enhanced creep properties of the P92 steel after the TMT, as reported previously, were considered to be mainly attributed to plenty of nano-sized Cr-rich M{sub 2}(C,N) carbonitrides produced by the TMT rather than to MX and M{sub 23}C{sub 6} precipitates. - Graphical abstract: TEM micrographs of precipitates on extraction carbon replicas prepared from ferritic/martensitic (F/M) steel P92. (a) After conventional heat treatment, normalized at 1050 °C for 30 min plus tempered at 765 °C for 1 h. (b) After a thermomechanical treatment (TMT), warm-rolled at 650 °C plus tempered at 650 °C for 1 h. Nano-sized precipitates with a high number density in the steel produced by the TMT were found to be Cr-rich M{sub 2}(C,N) carbonitride, rather than MX or M{sub 23}C{sub 6} phase. The TMT process inhibits the precipitation of M{sub 23}C{sub 6} and M{sub 5}C{sub 2} phases. Enhanced creep properties of the steel by the TMT are mainly attributed to plenty of nano-sized Cr-rich M{sub 2}(C,N) carbonitrides, rather than to MX and M{sub 23}C{sub 6} precipitates. It is suggested that plenty of nano-sized Cr-rich M{sub 2}(C,N) carbonitrides produced by the TMT are more helpful to improve the creep properties of the steel than M{sub 23}C{sub 6} plus MX precipitates obtained by the conventional heat treatment. - Highlights: •Carbon replicas were used for precisely identifying nano-sized phases in steel produced by TMT. •Densely nano-sized precipitates in P92 steel after TMT were found to be Cr-rich M{sub 2}(C,N) phase. •Fine precipitates produced by TMT can be M{sub 2}X phase instead of MX and/or M{sub 23}C{sub 6} phase. •Enhanced creep properties of P92 steel by TMT is attributed to fine M{sub 2}X, rather than to MX and M{sub 23}C{sub 6}. •TMT involving a tempering at 650 °C inhibits the formation of M{sub 23}C{sub 6}/M{sub 5}C{sub 2} phases in high-Cr steels.« less

Effective boson g factors in the mass 80 region

NASA Astrophysics Data System (ADS)

Mertzimekis, T. J.; Taylor, M. J.; Kumbartzki, G.; Benczer-Koller, N.; Stuchbery, A. E.

2002-10-01

Recent precision g factors have been obtained by using the transient field technique combined with Coulomb excitation in inverse kinematics in several, near spherical, nuclei around A ˜ 80. The g factors were analyzed in terms of an IBA-II formulation which treats the n and p boson effective g factors as mass-independent free parameters (A.Wolf et al.), Phys. Lett. B190, 19 (1987).. The data yielded more accurate effective boson g factors than obtained in the previous systematics for this region, g_π=0.50(3), g_ν=0.24(5) and g_π=0.45(3), g_ν=0.35(3) for the regions 28 <= N <= 50 and 38 <= N <= 50 respectively, with comparable i^2's. Evidence of shell closure for N=38 (K.-H. Speidel et al.), Phys. Rev. C57, 2181 (1998). prompted the need to examine these two regions separately. The deviations of g_π from unity and g_ν from zero indicate the importance of the underlying fermion structure.

Validation of a Computational Model for Autogenous Arc Welding

DTIC Science & Technology

1990-03-01

Structure of Austenitic Stainless Steels ." M1etallurgical 7Tansactions A, v.20A, May 1989. Zacharia. T., Eraslan. A.l.. and Aidun. D.K., "Modeling of...Figure 4. Temperature profiles for low and high conductivity flaws ........... 13 Figure 5. Rosenthal verification results...The sulfur contents (90 ppm and 24() ppn’n had a significant effect on the weld penetration for the GTA process for 304 stainless steel , however, there

The 25 percent-efficient GaAs Cassegrainian concentrator cell

NASA Technical Reports Server (NTRS)

Hamaker, H. C.; Grounner, M.; Kaminar, N. R.; Kuryla, M. S.; Ladle, M. J.; Liu, D. D.; Macmillan, H. F.; Partain, L. D.; Virshup, G. F.; Werthen, J. G.

1989-01-01

Very high-efficiency GaAs Cassegrainian solar cells have been fabricated in both the n-p and p-n configurations. The n-p configuration exhibits the highest efficiency at concentration, the best cells having an efficiency eta of 24.5 percent (100X, AM0, temperature T = 28 C). Although the cells are designed for operation at this concentration, peak efficiency is observed near 300 suns (eta = 25.1 percent). To our knowledge, this is the highest reported solar cell efficiency for space applications. The improvement in efficiency over that reported at the previous SPRAT conference is attributed primarily to lower series resistance and improved grid-line plating procedures. Using previously measured temperature coefficients, researchers estimate that the n-p GaAs cells should deliver approximately 22.5 percent efficiency at the operating conditions of 100 suns and T = 80 C. This performance exceeds the NASA program goal of 22 percent for the Cassegrainian cell. One hundred Cassegrainian cells have been sent to NASA as deliverables, sixty-eight in the n-p configuration and thirty-two in the p-n configuration.

Relative Modification of Prompt ψ ( 2 S ) and J / ψ Yields from p p to PbPb Collisions at s N N = 5.02 TeV

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sirunyan, A. M.; Tumasyan, A.; Adam, W.

The relative modification of the prompt ψ(2S) and J/ψ yields from pp to PbPb collisions, at the center-of-mass energy of 5.02 TeV per nucleon pair, is presented. The analysis is based on pp and PbPb data samples collected by the CMS experiment at the LHC in 2015, corresponding to integrated luminosities of 28.0 pb -1 and 464 μb -1, respectively. The double ratio of measured yields of prompt charmonia reconstructed through their decays into muon pairs, (N ψ(2S)/N J/ψ) PbPb/(N ψ(2S)/N J/ψ) pp, is determined as a function of PbPb collision centrality and charmonium transverse momentum p T, in two kinematicmore » intervals: |y|<1.6 covering 6.5< pT<30 GeV/c and 1.6<|y|<2.4 covering 3< pT<30 GeV/c. The centrality-integrated double ratios are 0.36 ± 0.08(stat) ±0.05 (syst) in the first interval and 0.24 ± 0.22(stat) ± 0.09 (syst) in the second. The double ratio is lower than unity in all the measured bins, suggesting that the ψ(2S) yield is more suppressed than the J/ψ yield in the explored phase space.« less

Relative Modification of Prompt ψ ( 2 S ) and J / ψ Yields from p p to PbPb Collisions at s N N = 5.02 TeV

DOE PAGES

Sirunyan, A. M.; Tumasyan, A.; Adam, W.; ...

2017-04-20

The relative modification of the prompt ψ(2S) and J/ψ yields from pp to PbPb collisions, at the center-of-mass energy of 5.02 TeV per nucleon pair, is presented. The analysis is based on pp and PbPb data samples collected by the CMS experiment at the LHC in 2015, corresponding to integrated luminosities of 28.0 pb -1 and 464 μb -1, respectively. The double ratio of measured yields of prompt charmonia reconstructed through their decays into muon pairs, (N ψ(2S)/N J/ψ) PbPb/(N ψ(2S)/N J/ψ) pp, is determined as a function of PbPb collision centrality and charmonium transverse momentum p T, in two kinematicmore » intervals: |y|<1.6 covering 6.5< pT<30 GeV/c and 1.6<|y|<2.4 covering 3< pT<30 GeV/c. The centrality-integrated double ratios are 0.36 ± 0.08(stat) ±0.05 (syst) in the first interval and 0.24 ± 0.22(stat) ± 0.09 (syst) in the second. The double ratio is lower than unity in all the measured bins, suggesting that the ψ(2S) yield is more suppressed than the J/ψ yield in the explored phase space.« less

Contribution of the first K-homology domain of poly(C)-binding protein 1 to its affinity and specificity for C-rich oligonucleotides

PubMed Central

Yoga, Yano M. K.; Traore, Daouda A. K.; Sidiqi, Mahjooba; Szeto, Chris; Pendini, Nicole R.; Barker, Andrew; Leedman, Peter J.; Wilce, Jacqueline A.; Wilce, Matthew C. J.

2012-01-01

Poly-C-binding proteins are triple KH (hnRNP K homology) domain proteins with specificity for single stranded C-rich RNA and DNA. They play diverse roles in the regulation of protein expression at both transcriptional and translational levels. Here, we analyse the contributions of individual αCP1 KH domains to binding C-rich oligonucleotides using biophysical and structural methods. Using surface plasmon resonance (SPR), we demonstrate that KH1 makes the most stable interactions with both RNA and DNA, KH3 binds with intermediate affinity and KH2 only interacts detectibly with DNA. The crystal structure of KH1 bound to a 5′-CCCTCCCT-3′ DNA sequence shows a 2:1 protein:DNA stoichiometry and demonstrates a molecular arrangement of KH domains bound to immediately adjacent oligonucleotide target sites. SPR experiments, with a series of poly-C-sequences reveals that cytosine is preferred at all four positions in the oligonucleotide binding cleft and that a C-tetrad binds KH1 with 10 times higher affinity than a C-triplet. The basis for this high affinity interaction is finally detailed with the structure determination of a KH1.W.C54S mutant bound to 5′-ACCCCA-3′ DNA sequence. Together, these data establish the lead role of KH1 in oligonucleotide binding by αCP1 and reveal the molecular basis of its specificity for a C-rich tetrad. PMID:22344691

Contribution of the first K-homology domain of poly(C)-binding protein 1 to its affinity and specificity for C-rich oligonucleotides.

PubMed

Yoga, Yano M K; Traore, Daouda A K; Sidiqi, Mahjooba; Szeto, Chris; Pendini, Nicole R; Barker, Andrew; Leedman, Peter J; Wilce, Jacqueline A; Wilce, Matthew C J

2012-06-01

Poly-C-binding proteins are triple KH (hnRNP K homology) domain proteins with specificity for single stranded C-rich RNA and DNA. They play diverse roles in the regulation of protein expression at both transcriptional and translational levels. Here, we analyse the contributions of individual αCP1 KH domains to binding C-rich oligonucleotides using biophysical and structural methods. Using surface plasmon resonance (SPR), we demonstrate that KH1 makes the most stable interactions with both RNA and DNA, KH3 binds with intermediate affinity and KH2 only interacts detectibly with DNA. The crystal structure of KH1 bound to a 5'-CCCTCCCT-3' DNA sequence shows a 2:1 protein:DNA stoichiometry and demonstrates a molecular arrangement of KH domains bound to immediately adjacent oligonucleotide target sites. SPR experiments, with a series of poly-C-sequences reveals that cytosine is preferred at all four positions in the oligonucleotide binding cleft and that a C-tetrad binds KH1 with 10 times higher affinity than a C-triplet. The basis for this high affinity interaction is finally detailed with the structure determination of a KH1.W.C54S mutant bound to 5'-ACCCCA-3' DNA sequence. Together, these data establish the lead role of KH1 in oligonucleotide binding by αCP1 and reveal the molecular basis of its specificity for a C-rich tetrad.

An Electrochemical Investigation of Corrosion Rates for 1020 Steel in Environments Which Simulate Conditions in Marine Reinforced Concrete.

DTIC Science & Technology

1981-06-01

which affect the corrosion of steel in concrete. The effects of moisture content [21, 22] of the concrete and the use of inhibitors in concrete mixes...use of inhibitors to reduce or eliminate corrosion. 3. The use of different alloys as rebar. 4. The use of cathodic protection in new and...8217- qq q or-wwr- - 4 m ON unlw Nr H E4E-4 0 vv o ~ o wq O % UU%D www AI L % z H Z 00 %ocnrj %o w o w (% N or csq r- qr IM c4 n NLn r- r -w 00 ’ 04

An investigation of laser cutting quality of 22MnB5 ultra high strength steel using response surface methodology

NASA Astrophysics Data System (ADS)

Tahir, Abdul Fattah Mohd; Aqida, Syarifah Nur

2017-07-01

In hot press forming, changes of mechanical properties in boron steel blanks have been a setback in trimming the final shape components. This paper presents investigation of kerf width and heat affected zone (HAZ) of ultra high strength 22MnB5 steel cutting. Sample cutting was conducted using a 4 kW Carbon Dioxide (CO2) laser machine with 10.6 μm wavelength with the laser spot size of 0.2 mm. A response surface methodology (RSM) using three level Box-Behnken design of experiment was developed with three factors of peak power, cutting speed and duty cycle. The parameters were optimised for minimum kerf width and HAZ formation. Optical evaluation using MITUTOYO TM 505 were conducted to measure the kerf width and HAZ region. From the findings, laser duty cycle was crucial to determine cutting quality of ultra-high strength steel; followed by cutting speed and laser power. Meanwhile, low power intensity with continuous wave contributes the narrowest kerf width formation and least HAZ region.

Inherent Error in Asynchronous Digital Flight Controls.

DTIC Science & Technology

1980-02-01

IMAXJ DIIMENSION AP(2,2) PBIP(2v2),CP(lv2) ,FC(2,2) iGC(2,1) , PHIT ’(4,4), I HC(2v2)vEC(2w1)wPHITI(4,4,l01),PSITI(4,4),PHTAU(4,4) ,PSTAU(4,4),I 4 INJ3EX(4...1.0 4 02. CON’T I NUE [𔃺 4 11 :: 2 7NT TI =T14-E:’LTA PHITl(2yJ1,11) =0.0 4 FHIT1(2y2vlJ.) EXP(-10.*TI) [DO 400 11 = lNP DO0 400 JJ = INP 400 PHIT (IlJJ...PHIT1(IIr,J.JYN’T) WRITE(6y860) 860 FORMAT (5X Y’PH IT’) [DO 861 1 -IYiNP 1361 WRITE(6v802) ( PHIT (I9vJ) ,J:=1,NP) DO :1800 KK2 1,J.6 IAU N1

Design of Steel Structures to Resist the Effects of HE Explosions

DTIC Science & Technology

1975-08-01

n-;)L]- )AbFdcosY SCOMSINIED MECHANISMm C , , (2n- w Mp t4 CM5 , ngM w Number )ff oAh~d M boys -- ,2, 3.. /,,’ b~dy ---1~ bF~ w zUniform bbd T/d SL L_...mink’ccli Hs F d 1)Vnamlc yield, ,v: sili-dr s~zcss (psL) F d Dynanic v t’ I’! rr (psi) F’ J Kuler buckling: %tr.’srns t2. td ’ v s.iS&’tv Iacto’r I(p>-’, F1

78 FR 56242 - Notice of Realty Action: Competitive Sale of 28 Parcels of Public Land in Clark County, NV

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-12

... acres: T. 20 S., R. 60 E., Sec. 6, NW\\1/4\\SW\\1/4\\SE\\1/4\\, W\\1/2\\NE\\1/4\\SW\\1/4\\SE\\1/4\\, NE\\1/4\\NE\\1/4\\SW\\1/4\\SE\\1/4\\. N-78190, 2.50 acres: T. 22 S., R. 60 E., Sec. 14, NW\\1/4\\SW\\1/4\\NW\\1/4\\SW\\1/4\\. N-91783, 5.00 acres: T. 22 S., R. 60 E., Sec. 14, S\\1/2\\SW\\1/4\\SW\\1/4\\SW\\1/4\\. N-91794, 10.00 acres: T. 22 S...

C3H7NO2S effect on concrete steel-rebar corrosion in 0.5 M H2SO4 simulating industrial/microbial environment

NASA Astrophysics Data System (ADS)

Okeniyi, Joshua Olusegun; Nwadialo, Christopher Chukwuweike; Olu-Steven, Folusho Emmanuel; Ebinne, Samaru Smart; Coker, Taiwo Ebenezer; Okeniyi, Elizabeth Toyin; Ogbiye, Adebanji Samuel; Durotoye, Taiwo Omowunmi; Badmus, Emmanuel Omotunde Oluwasogo

2017-02-01

This paper investigates C3H7NO2S (Cysteine) effect on the inhibition of reinforcing steel corrosion in concrete immersed in 0.5 M H2SO4, for simulating industrial/microbial environment. Different C3H7NO2S concentrations were admixed, in duplicates, in steel-reinforced concrete samples that were partially immersed in the acidic sulphate environment. Electrochemical monitoring techniques of open circuit potential, as per ASTM C876-91 R99, and corrosion rate, by linear polarization resistance, were then employed for studying anticorrosion effect in steel-reinforced concrete samples by the organic hydrocarbon admixture. Analyses of electrochemical test-data followed ASTM G16-95 R04 prescriptions including probability distribution modeling with significant testing by Kolmogorov-Smirnov and student's t-tests statistics. Results established that all datasets of corrosion potential distributed like the Normal, the Gumbel and the Weibull distributions but that only the Weibull model described all the corrosion rate datasets in the study, as per the Kolmogorov-Smirnov test-statistics. Results of the student's t-test showed that differences of corrosion test-data between duplicated samples with the same C3H7NO2S concentrations were not statistically significant. These results indicated that 0.06878 M C3H7NO2S exhibited optimal inhibition efficiency η = 90.52±1.29% on reinforcing steel corrosion in the concrete samples immersed in 0.5 M H2SO4, simulating industrial/microbial service-environment.

A benchmark theoretical study of the electronic ground state and of the singlet-triplet split of benzene and linear acenes

NASA Astrophysics Data System (ADS)

Hajgató, B.; Szieberth, D.; Geerlings, P.; De Proft, F.; Deleuze, M. S.

2009-12-01

A benchmark theoretical study of the electronic ground state and of the vertical and adiabatic singlet-triplet (ST) excitation energies of benzene (n =1) and n-acenes (C4n+2H2n+4) ranging from naphthalene (n =2) to heptacene (n =7) is presented, on the ground of single- and multireference calculations based on restricted or unrestricted zero-order wave functions. High-level and large scale treatments of electronic correlation in the ground state are found to be necessary for compensating giant but unphysical symmetry-breaking effects in unrestricted single-reference treatments. The composition of multiconfigurational wave functions, the topologies of natural orbitals in symmetry-unrestricted CASSCF calculations, the T1 diagnostics of coupled cluster theory, and further energy-based criteria demonstrate that all investigated systems exhibit a A1g singlet closed-shell electronic ground state. Singlet-triplet (S0-T1) energy gaps can therefore be very accurately determined by applying the principles of a focal point analysis onto the results of a series of single-point and symmetry-restricted calculations employing correlation consistent cc-pVXZ basis sets (X=D, T, Q, 5) and single-reference methods [HF, MP2, MP3, MP4SDQ, CCSD, CCSD(T)] of improving quality. According to our best estimates, which amount to a dual extrapolation of energy differences to the level of coupled cluster theory including single, double, and perturbative estimates of connected triple excitations [CCSD(T)] in the limit of an asymptotically complete basis set (cc-pV∞Z), the S0-T1 vertical excitation energies of benzene (n =1) and n-acenes (n =2-7) amount to 100.79, 76.28, 56.97, 40.69, 31.51, 22.96, and 18.16 kcal/mol, respectively. Values of 87.02, 62.87, 46.22, 32.23, 24.19, 16.79, and 12.56 kcal/mol are correspondingly obtained at the CCSD(T)/cc-pV∞Z level for the S0-T1 adiabatic excitation energies, upon including B3LYP/cc-PVTZ corrections for zero-point vibrational energies. In line with the absence of Peierls distortions, extrapolations of results indicate a vanishingly small S0-T1 energy gap of 0 to ˜4 kcal/mol (˜0.17 eV) in the limit of an infinitely large polyacene.

Hydraulic Design of Navigation Locks

DTIC Science & Technology

1989-09-01

service brought about by surface deposits, erossion, corrosion , bacterial slimes and growths and marine and fresh water fouling. Experience of similar...Drawn brass, copper, alluminium , etc. 0.0025 Glass, plastic, perspex, fibre glass, etc. 0.0025 2. Steel pipes New smooth pipes 0.025 Centrifugally...1 H l I T j I 1 1 In E 1- 0 C D I ) N N C4dv Fig. .1. oodyChar TBT7 2. Adequate initial protection to prevent corrosion and erosion. 3. Chlorination

Rubrobacter spartanus sp. nov., a moderately thermophilic oligotrophic bacterium isolated from volcanic soil.

PubMed

Norman, Jeffrey S; King, Gary M; Friesen, Maren L

2017-09-01

Bacterial strain HPK2-2T was isolated from soil adjacent to the caldera of Kilauea Volcano in Hawaii Volcanoes National Park. HPK2-2T is a chemoorganoheterotroph that shows optimal growth at 50 °C (range 45-55 °C) and pH 8.0 (range 5.0-10.0). Sequence analysis of the 16S subunit of the rRNA gene showed that HPK2-2T is most closely related to the type strain of Rubrobactertaiwanensis (ATCC BAA-406T), with which it shared 94.5 % sequence identity. The major fatty acids detected in HPK2-2T were C18 : 0 14-methyl and C16 : 0 12-methyl; internally branched fatty acids such as these are characteristic of the genus Rubrobacter. The only respiratory quinone detected was MK-8, which is the major respiratory quinone for all members of the family Rubrobacteraceae examined thus far. We propose that HPK2-2T represents a novel species of the genus Rubrobacter, for which we propose the name Rubrobacterspartanus (type strain HPK2-2T; DSM 102139T; LMG 29988T).

Thermophysical and Electronic Properties of Foreign Stainless Steels, A Comprehensive Survey of the World Literature,

DTIC Science & Technology

1981-11-01

included in its companion volume on nonstainless alloy steels carbon steels and cast irons. The TEPIAC retrieval system is based on assigning a seven...LOEFFILIENTS OF STRTUCTURAL M;.TE.)IALS AT LOW A. T,-E Tt-i!1AL 0,)NCuCfIVITY AND ITHE THERIIAL T ImA-FRi.Tu’ES. 11,fC’.4T OF IROI. AND STEELS It, THE Hlf...PROPERTIES OF FOREIGN STAINLESS STEELS A Comprehensive Survey of the World Literature P.D. DESAI CINDAS REPORT 61 November 1981 DTICS ELECTE Prepared by 0U

Elliptic flow of electrons from heavy-flavor hadron decays in Au + Au collisions at √{sN N}=200 , 62.4, and 39 GeV

NASA Astrophysics Data System (ADS)

Adamczyk, L.; Adkins, J. K.; Agakishiev, G.; Aggarwal, M. M.; Ahammed, Z.; Ajitanand, N. N.; Alekseev, I.; Anderson, D. M.; Aoyama, R.; Aparin, A.; Arkhipkin, D.; Aschenauer, E. C.; Ashraf, M. U.; Attri, A.; Averichev, G. S.; Bai, X.; Bairathi, V.; Behera, A.; Bellwied, R.; Bhasin, A.; Bhati, A. K.; Bhattarai, P.; Bielcik, J.; Bielcikova, J.; Bland, L. C.; Bordyuzhin, I. G.; Bouchet, J.; Brandenburg, J. D.; Brandin, A. V.; Brown, D.; Bunzarov, I.; Butterworth, J.; Caines, H.; Calderón de la Barca Sánchez, M.; Campbell, J. M.; Cebra, D.; Chakaberia, I.; Chaloupka, P.; Chang, Z.; Chankova-Bunzarova, N.; Chatterjee, A.; Chattopadhyay, S.; Chen, X.; Chen, J. H.; Chen, X.; Cheng, J.; Cherney, M.; Christie, W.; Contin, G.; Crawford, H. J.; Das, S.; De Silva, L. C.; Debbe, R. R.; Dedovich, T. G.; Deng, J.; Derevschikov, A. A.; Didenko, L.; Dilks, C.; Dong, X.; Drachenberg, J. L.; Draper, J. E.; Dunkelberger, L. E.; Dunlop, J. C.; Efimov, L. G.; Elsey, N.; Engelage, J.; Eppley, G.; Esha, R.; Esumi, S.; Evdokimov, O.; Ewigleben, J.; Eyser, O.; Fatemi, R.; Fazio, S.; Federic, P.; Federicova, P.; Fedorisin, J.; Feng, Z.; Filip, P.; Finch, E.; Fisyak, Y.; Flores, C. E.; Fulek, L.; Gagliardi, C. A.; Garand, D.; Geurts, F.; Gibson, A.; Girard, M.; Grosnick, D.; Gunarathne, D. S.; Guo, Y.; Gupta, S.; Gupta, A.; Guryn, W.; Hamad, A. I.; Hamed, A.; Harlenderova, A.; Harris, J. W.; He, L.; Heppelmann, S.; Heppelmann, S.; Hirsch, A.; Hoffmann, G. W.; Horvat, S.; Huang, H. Z.; Huang, X.; Huang, B.; Huang, T.; Humanic, T. J.; Huo, P.; Igo, G.; Jacobs, W. W.; Jentsch, A.; Jia, J.; Jiang, K.; Jowzaee, S.; Judd, E. G.; Kabana, S.; Kalinkin, D.; Kang, K.; Kauder, K.; Ke, H. W.; Keane, D.; Kechechyan, A.; Khan, Z.; Kikoła, D. P.; Kisel, I.; Kisiel, A.; Kochenda, L.; Kocmanek, M.; Kollegger, T.; Kosarzewski, L. K.; Kraishan, A. F.; Kravtsov, P.; Krueger, K.; Kulathunga, N.; Kumar, L.; Kvapil, J.; Kwasizur, J. H.; Lacey, R.; Landgraf, J. M.; Landry, K. D.; Lauret, J.; Lebedev, A.; Lednicky, R.; Lee, J. H.; Li, X.; Li, C.; Li, Y.; Li, W.; Lidrych, J.; Lin, T.; Lisa, M. A.; Liu, P.; Liu, Y.; Liu, F.; Liu, H.; Ljubicic, T.; Llope, W. J.; Lomnitz, M.; Longacre, R. S.; Luo, X.; Luo, S.; Ma, Y. G.; Ma, L.; Ma, R.; Ma, G. L.; Magdy, N.; Majka, R.; Mallick, D.; Margetis, S.; Markert, C.; Matis, H. S.; Meehan, K.; Mei, J. C.; Miller, Z. W.; Minaev, N. G.; Mioduszewski, S.; Mishra, D.; Mizuno, S.; Mohanty, B.; Mondal, M. M.; Morozov, D. A.; Mustafa, M. K.; Nasim, Md.; Nayak, T. K.; Nelson, J. M.; Nie, M.; Nigmatkulov, G.; Niida, T.; Nogach, L. V.; Nonaka, T.; Nurushev, S. B.; Odyniec, G.; Ogawa, A.; Oh, K.; Okorokov, V. A.; Olvitt, D.; Page, B. S.; Pak, R.; Pandit, Y.; Panebratsev, Y.; Pawlik, B.; Pei, H.; Perkins, C.; Pile, P.; Pluta, J.; Poniatowska, K.; Porter, J.; Posik, M.; Poskanzer, A. M.; Pruthi, N. K.; Przybycien, M.; Putschke, J.; Qiu, H.; Quintero, A.; Ramachandran, S.; Ray, R. L.; Reed, R.; Rehbein, M. J.; Ritter, H. G.; Roberts, J. B.; Rogachevskiy, O. V.; Romero, J. L.; Roth, J. D.; Ruan, L.; Rusnak, J.; Rusnakova, O.; Sahoo, N. R.; Sahu, P. K.; Salur, S.; Sandweiss, J.; Saur, M.; Schambach, J.; Schmah, A. M.; Schmidke, W. B.; Schmitz, N.; Schweid, B. R.; Seger, J.; Sergeeva, M.; Seyboth, P.; Shah, N.; Shahaliev, E.; Shanmuganathan, P. V.; Shao, M.; Sharma, M. K.; Sharma, A.; Shen, W. Q.; Shi, Z.; Shi, S. S.; Shou, Q. Y.; Sichtermann, E. P.; Sikora, R.; Simko, M.; Singha, S.; Skoby, M. J.; Smirnov, N.; Smirnov, D.; Solyst, W.; Song, L.; Sorensen, P.; Spinka, H. M.; Srivastava, B.; Stanislaus, T. D. S.; Stock, R.; Strikhanov, M.; Stringfellow, B.; Sugiura, T.; Sumbera, M.; Summa, B.; Sun, Y.; Sun, X. M.; Sun, X.; Surrow, B.; Svirida, D. N.; Tang, A. H.; Tang, Z.; Taranenko, A.; Tarnowsky, T.; Tawfik, A.; Thäder, J.; Thomas, J. H.; Timmins, A. R.; Tlusty, D.; Todoroki, T.; Tokarev, M.; Trentalange, S.; Tribble, R. E.; Tribedy, P.; Tripathy, S. K.; Trzeciak, B. A.; Tsai, O. D.; Ullrich, T.; Underwood, D. G.; Upsal, I.; Van Buren, G.; van Nieuwenhuizen, G.; Vasiliev, A. N.; Videbæk, F.; Vokal, S.; Voloshin, S. A.; Vossen, A.; Wang, G.; Wang, Y.; Wang, F.; Wang, Y.; Webb, J. C.; Webb, G.; Wen, L.; Westfall, G. D.; Wieman, H.; Wissink, S. W.; Witt, R.; Wu, Y.; Xiao, Z. G.; Xie, W.; Xie, G.; Xu, J.; Xu, N.; Xu, Q. H.; Xu, W.; Xu, Y. F.; Xu, Z.; Yang, Y.; Yang, Q.; Yang, C.; Yang, S.; Ye, Z.; Ye, Z.; Yi, L.; Yip, K.; Yoo, I.-K.; Yu, N.; Zbroszczyk, H.; Zha, W.; Zhang, Z.; Zhang, X. P.; Zhang, J. B.; Zhang, S.; Zhang, J.; Zhang, Y.; Zhang, J.; Zhang, S.; Zhao, J.; Zhong, C.; Zhou, L.; Zhou, C.; Zhu, X.; Zhu, Z.; Zyzak, M.; STAR Collaboration

2017-03-01

We present measurements of elliptic flow (v2) of electrons from the decays of heavy-flavor hadrons (eHF) by the STAR experiment. For Au+Au collisions at √{sN N}=200 GeV we report v2, for transverse momentum (pT) between 0.2 and 7 GeV /c , using three methods: the event plane method (v2{EP } ), two-particle correlations (v2{2 } ), and four-particle correlations (v2{4 } ). For Au+Au collisions at √{sN N}=62.4 and 39 GeV we report v2{2 } for pT<2 GeV /c . v2{2 } and v2{4 } are nonzero at low and intermediate pT at 200 GeV, and v2{2 } is consistent with zero at low pT at other energies. The v2{2 } at the two lower beam energies is systematically lower than at √{sN N}=200 GeV for pT<1 GeV /c . This difference may suggest that charm quarks interact less strongly with the surrounding nuclear matter at those two lower energies compared to √{sN N}=200 GeV.

Influence of the redox active ligand on the reactivity and electronic structure of a series of Fe(TIM) complexes.

PubMed

Hess, Corinna R; Weyhermüller, Thomas; Bill, Eckhard; Wieghardt, Karl

2010-06-21

The redox properties of Fe and Zn complexes coordinated by an alpha-diimine based N(4)-macrocyclic ligand (TIM) have been examined using spectroscopic methods and density functional theory (DFT) computational analysis. DFT results on the redox series of [Zn(TIM*)](n) and [Fe(TIM*)](n) molecules indicate the preferential reduction of the alpha-diimine ligand moiety. In addition to the previously reported [Fe(TIM*)](2) dimer, we have now synthesized and characterized a further series of monomeric and dimeric complexes coordinated by the TIM ligand. This includes the five-coordinate monomeric [Fe(TIM*)I], the neutral and cationic forms of a monomeric phosphite adduct, [Fe(TIM*)(P(OPh)(3))] and [Fe(TIM*)(P(OPh)(3))](PF(6)), as well as a binuclear hydroxy-bridged complex, [{Fe(TIM*)}(2)(mu-OH)](PF(6)). Experimental and computational data for these synthetic compounds denote the presence of ferrous and ferric species, suggesting that the alpha-diimine based macrocycles do not readily support the formation of formally low-valent (M(0) or M(I)) metal complexes as previously speculated. Magnetochemical, Mossbauer, electron paramagnetic resonance (EPR), and electronic spectral data have been employed to experimentally determine the oxidation state of the central metal ion and of the macrocyclic ligand (TIM*) in each compound. The series of compounds is described as follows: [Fe(II)(TIM(0))(CH(3)CN(2))](2+), S(Fe) = S(T) = 0; [Fe(2.5)(TIM(2.5-))](2), S(T) = 1; [{Fe(III)(TIM(2-))}(2)(mu-OH)](+), S(Fe) = 3/2, S(T) = 0; [Fe(III)(TIM(2-))I], S(Fe) = 3/2, S(T) = 1/2; [Fe(II)(TIM(2-))(P(OPh(3)))], S(Fe) = S(T) = 0; and [Fe(II)(TIM(1-))(P(OPh(3)))](1+)/[Fe(I)(TIM(0))(P(OPh(3)))](1+), S(T) = 1/2. The results have been corroborated by DFT calculations.

A novel ultrafine-grained Fe−22Mn−0.6C TWIP steel with superior strength and ductility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tian, Y.Z., E-mail: yztian@imr.ac.cn

A fully recrystallized ultrafine-grained (UFG) Fe−22wt.%Mn−0.6wt.%C twinning-induced plasticity (TWIP) steel with mean grain size of 576 nm was fabricated by cold rolling and annealing process. Tensile test showed that this UFG steel possessed high yield strength of 785 MPa, and unprecedented uniform elongation of 48%. The Hall-Petch relationship was verified from the coarse-grained (CG) regime to the ultrafine-grained (UFG) regime. The microstructures at specified tensile strains were characterized by electron backscattered diffraction (EBSD) and transmission electron microscopy (TEM). The microstructures and strain hardening behavior of the UFG TWIP steel were compared with the CG counterpart. The strong strain hardening capabilitymore » of the UFG steel is supposed to be responsible for the high strength and good ductility. - Highlights: • A fully recrystallized Fe−22Mn−0.6C TWIP steel with mean grain size of 576 nm was fabricated. • The ultrafine-grained (UFG) steel exhibits strong strain-hardening capability, excellent strength and ductility. • The Hall-Petch relationship is fitted well from the CG regime to the UFG regime.« less

A study of the contact interaction between a plate with a hole and a washer in the presence of clearances and interferences

NASA Astrophysics Data System (ADS)

Grishin, V. I.

The contact interaction between a plate with a hole and a washer fitted into the hole with a clearance or an interference is investigated analytically using a finite element method implemented in a computer code. Data on changes in stress concentration with the distance from the filled hole to the plate edge are obtained for several materials, including D16-T, AK4-1, V95-T, OT4-1, 30KhGSA, and 30KhGSNA alloys.

Thulium fiber laser induced vapor bubbles using bare, tapered, ball, hollow steel, and muzzle brake fiber optic tips

NASA Astrophysics Data System (ADS)

Gonzalez, David A.; Hardy, Luke A.; Hutchens, Thomas C.; Irby, Pierce B.; Fried, Nathaniel M.

2018-02-01

This study characterizes laser-induced vapor bubbles for five distal fiber optic tip configurations, to provide insight into stone retropulsion experienced during laser ablation of kidney stones. A TFL with 1908-nm wavelength delivered 34 mJ energy per pulse at 500-μs pulse duration through five different fibers: 100-μm-core/170-μm-OD bare fiber tip, 150-μm- to 300-μm-core tapered fiber tip, 100-μm-core/300-μm-OD ball tip fiber, 100-μm-core/340- μm-OD hollow steel tip fiber, and 100-μm-core/560-μm-OD muzzle brake fiber tip. A high speed camera with 10- μm spatial and 9.5-μs temporal resolution imaged vapor bubble dynamics. A needle hydrophone measured pressure transients in forward (0°) and side (90°) directions while placed at a 6.8 +/- 0.4 mm distance from fiber tip. Maximum bubble dimensions (width/length) averaged 0.7/1.5, 1.0/1.6, 0.5/1.1, 0.8/1.9, and 0.7/1.5 mm, for bare, tapered, ball, hollow steel, and muzzle tips, respectively (n=5). The hollow steel tip exhibited the most elongated vapor bubble shape, translating into increased forward pressure in this study and consistent with higher stone retropulsion in previous reports. Relative pressures (a.u.) in (forward/side) directions averaged 1.7/1.6, 2.0/2.0, 1.4/1.2, 6.8/1.1, and 0.3/1.2, for each fiber tip (n=5). For hollow steel tip, forward pressure was 4× higher than for bare fiber. For the muzzle brake fiber tip, forward pressure was 5× lower than for bare fiber. Bubble dimensions and pressure measurements demonstrated that the muzzle tip reduced forward pressure by partially venting vapors through side holes, consistent with lower stone retropulsion observed in previous reports.

Docosahexaenoic Acid and Eicosapentaenoic Acid Did not Alter trans-10,cis-12 Conjugated Linoleic Acid Incorporation into Mice Brain and Eye Lipids.

PubMed

Vemuri, Madhuri; Adkins, Yuriko; Mackey, Bruce E; Kelley, Darshan S

2017-09-01

trans 10,cis 12-CLA has been reported to alter fatty acid composition in several non-neurological tissues, but its effects are less known in neurological tissues. Therefore, the purpose of this study was to determine if CLA supplementation would alter brain and eye fatty acid composition and if those changes could be prevented by concomitant supplementation with docosahexaenoic acid (DHA; 22:6n3) or eicosapentaenoic acid (EPA; 20:5n3). Eight-week-old, pathogen-free C57BL/6N female mice (n = 6/group) were fed either the control diet or diets containing 0.5% (w/w) t10,c12-CLA in the presence or absence of either 1.5% DHA or 1.5% EPA for 8 weeks. CLA concentration was significantly (P < 0.05) greater in the eye but not in the brain lipids of the CLA group when compared with the control group. The sums of saturated, monounsaturated, polyunsaturated fatty acids, and n3:n6 ratio did not differ between these two groups for both tissues. The n3:n6 ratio and concentrations of 20:5n3 and 22:5n3 were significantly greater, and those of 20:4n6, 22:4n6, and 22:5n6 were lesser in the CLA + DHA and CLA + EPA groups than in the control and CLA groups for either tissue. DHA concentration was higher in the CLA + DHA group only but not in the CLA + EPA group when compared with the CLA group for both tissues. The dietary fatty acids generally induced similar changes in brain and eye fatty acid concentration and at the concentrations used both DHA and EPA fed individually with CLA were more potent than CLA alone in altering the tissue fatty acid concentration.

Strengthening and Toughening of a Heavy Plate Steel for Shipbuilding with Yield Strength of Approximately 690 MPa

NASA Astrophysics Data System (ADS)

Liu, Dongsheng; Cheng, Binggui; Chen, Yuanyuan

2013-01-01

HSLA-100 steel with high content of alloying elements (nominally in wt pct, 3.5 Ni, 1.6 Cu, and 0.6Mo) is now used to produce heavy plates for constructing a hull and drilling platform. We proposed here a substantially leaner steel composition (containing 1.7 Ni, 1.1 Cu, and 0.5Mo) to produce a heavy plate to 80 mm thickness with mechanical properties comparable with those of the HSLA-100 grade. A continuous cooling transformation (CCT) diagram of the steel was constructed. Key parameters of thermal treatment and revealing mechanisms of strengthening and toughening were derived based on industrial production trials. The microstructures of the 80-mm-thick plate were lath-like bainite (LB) at near surface of the quarter thickness ( t/4), and granular bainite (GB)+LB at center thickness ( t/2) after solutionizing and water quenching (Q). The effect of tempering (T) on the microstructures and properties of the plate was investigated. Excellent combination of room temperature strength and low-temperature Charpy V-notch (CVN) toughness approximately equivalent to that of the HSLA 100 grade (YS > 690 MPa, CVN energy >100 J even at 193 K [-80 °C]) was achieved in the plate treated by the QT process with tempering temperature of 898 K (625 °C). The combination of strength and toughness at t/4 is superior to that at t/2 of the plate under both as-quenched and QT conditions. This result is attributed to that the fraction of high-angle grain boundaries (HAGBs) at t/4 is higher than that at t/2.

Theoretical Stark broadening parameters for spectral lines arising from the 2p5ns, 2p5np and 2p5nd electronic configurations of Mg III

NASA Astrophysics Data System (ADS)

Colón, C.; Moreno-Díaz, C.; Alonso-Medina, A.

2013-10-01

In the present work we report theoretical Stark widths and shifts calculated using the Griem semi-empirical approach, corresponding to 237 spectral lines of Mg III. Data are presented for an electron density of 1017 cm-3 and temperatures T = 0.5-10.0 (104K). The matrix elements used in these calculations have been determined from 23 configurations of Mg III: 2s22p6, 2s22p53p, 2s22p54p, 2s22p54f and 2s22p55f for even parity and 2s22p5ns (n = 3-6), 2s22p5nd (n = 3-9), 2s22p55g and 2s2p6np (n = 3-8) for odd parity. For the intermediate coupling (IC) calculations, we use the standard method of least-squares fitting from experimental energy levels by means of the Cowan computer code. Also, in order to test the matrix elements used in our calculations, we present calculated values of 70 transition probabilities of Mg III spectral lines and 14 calculated values of radiative lifetimes of Mg III levels. There is good agreement between our calculations and experimental radiative lifetimes. Spectral lines of Mg III are relevant in astrophysics and also play an important role in the spectral analysis of laboratory plasma. Theoretical trends of the Stark broadening parameter versus the temperature for relevant lines are presented. No values of Stark parameters can be found in the bibliography.

A Computer Code to Calculate Emission and Transmission of Infrared Radiation through Non-Equilibrium Atmospheres.

DTIC Science & Technology

1983-07-08

A(xPCQNWL SEARCI THE. LINE FILE rbN,5, C’ 129 lIE,’ CM-I FOR LINES OF *,A&’,/,5X, III 2-- - ’IS C CFE =’,14,/95xs 131 T’e;NO =,IX .5,’ - ,x5/5, 1 32...15407wE’C8 131 -7e.3(5 221.141 .11Z230"J7 .1462zGE*1e 132 487.34C 22?.w53 .10S47C1-,7 .1.84E01.18 133 %9( Zfl375 22 -,E su 11M -0 7 klu 136 523.410 22M...144 589.530 23C.441 SME0043E-08 .2294301.07 145 59?.fi1C 23r.420 GsC?jlnF- .;cc.2iFtc7 146 604.490 iO35 .5345431-08 E271?53E*C7 14? R1lf LAIC t. 131

Diversity of Bacillus-like bacterial community in the sediments of the Bamenwan mangrove wetland in Hainan, China.

PubMed

Liu, Min; Cui, Ying; Chen, Yuqing; Lin, Xiangzhi; Huang, Huiqin; Bao, Shixiang

2017-03-01

Members of the genus Bacillus and related spore-forming genera are ubiquitous. However, Bacillus-like species isolated from marine sediments have attracted less interest than their terrestrial relatives. Here, we investigated the diversity of Bacillus-like bacterial communities in the sediments of the Bamenwan mangrove wetland in Hainan, China, using culture-dependent and culture-independent methods, and present the first report on this subject. We also discovered some potential novel species from the sediment samples. Four families, Bacillaceae (58%), Paenibacillaceae (22%), Alicyclobacillaceae (15%), and Planococcaceae (5%), and 9 genera, Bacillus (42%), Paenibacillus (16%), Halobacillus (13%), Alicyclobacillus (11%), Rummeliibacillus (5%), Cohnella (5%), Tumebacillus (4%), Pontibacillus (3%), and Aneurinibacillus (2%), were identified by pyrosequencing. In contrast, only 4 genera, Bacillus (57%), Paenibacillus (23%), Halobacillus (14%), and Virgibacillus (6%), were detected by the culture-dependent method. In the 16S rDNA sequencing analysis, the isolates HB12036 and HB12037 were closest to Bacillus okuhidensis Kh10-101 T and Paenibacillus xylanilyticus XIL14 T with similarities of 94.8% and 95.9%, respectively, indicating that these were novel species. Bacillus sp. HB12035 and HB12040 exhibited antimicrobial activity against Staphylococcus aureus ATCC 25923, and Bacillus sp. HB12033 exhibited antimicrobial activity against Ustilago scitaminea Syd.

Microstructural development under irradiation in European ODS ferritic/martensitic steels

NASA Astrophysics Data System (ADS)

Schäublin, R.; Ramar, A.; Baluc, N.; de Castro, V.; Monge, M. A.; Leguey, T.; Schmid, N.; Bonjour, C.

2006-06-01

Oxide dispersion strengthened steels based on the ferritic/martensitic steel EUROFER97 are promising candidates for a fusion reactor because of their improved high temperature mechanical properties and their potential higher radiation resistance relative to the base material. Several EUROFER97 based ODS F/M steels are investigated in this study. There are the Plansee ODS steels containing 0.3 wt% yttria, and the CRPP ODS steels, whose production route is described in detail. The reinforcing particles represent 0.3-0.5% weight and are composed of yttria. The effect of 0.3 wt% Ti addition is studied. ODS steel samples have been irradiated with 590 MeV protons to 0.3 and 1.0 dpa at room temperature and 350 °C. Microstructure is investigated by transmission electron microscopy and mechanical properties are assessed by tensile and Charpy tests. While the Plansee ODS presents a ferritic structure, the CRPP ODS material presents a tempered martensitic microstructure and a uniform distribution of the yttria particles. Both materials provide a yield stress higher than the base material, but with reduced elongation and brittle behaviour. Ti additions improve elongation at high temperatures. After irradiation, mechanical properties of the material are only slightly altered with an increase in the yield strength, but without significant decrease in the total elongation, relative to the base material. Samples irradiated at room temperature present radiation induced defects in the form of blacks dots with a size range from 2 to 3 nm, while after irradiation at 350 °C irradiation induced a0<1 0 0>{1 0 0} dislocation loops are clearly visible along with nanocavities. The dispersed yttria particles with an average size of 6-8 nm are found to be stable for all irradiation conditions. The density of the defects and the dispersoid are measured and found to be about 2.3 × 10 22 m -3 and 6.2 × 10 22 m -3, respectively. The weak impact of irradiation on mechanical properties of ODS F/M steel is thus explained by a lower density of irradiation induced defects relative to the density of reinforcing particles.

Optimization of D-lactic acid production using unutilized biomass as substrates by multiple parallel fermentation.

PubMed

Mufidah, Elya; Wakayama, Mamoru

2016-12-01

This study investigated the optimization of D-lactic acid production from unutilized biomass, specifically banana peel and corncob by multiple parallel fermentation (MPF) with Leuconostoc mesenteroides and Aspergillus awamori. The factors involved in MPF that were assessed in this study comprised banana peel and corncob, KH 2 PO 4 , Tween 80, MgSO 4 ·7H 2 O, NaCl, yeast extract, and diammonium hydrogen citrate to identify the optimal concentration for D-lactic acid production. Optimization of these component factors was performed using the Taguchi method with an L8 orthogonal array. The optimal concentrations for the effectiveness of MPF using biomass substrates were as follows: (1) banana peel, D-lactic acid production was 31.8 g/L in medium containing 15 % carbon source, 0.5 % KH 2 PO 4 , 0.1 % Tween 80, 0.05 % MgSO 4 ·7H 2 O, 0.05 % NaCl, 1.5 % yeast extract, and 0.2 % diammonium hydrogen citrate. (2) corncob, D-lactic acid production was 38.3 g/L in medium containing 15 % of a carbon source, 0.5 % KH 2 PO 4 , 0.1 % Tween 80, 0.05 % MgSO 4 ·7H 2 O, 0.1 % NaCl, 1.0 % yeast extract, and 0.4 % diammonium hydrogen citrate. Thus, both banana peel and corncob are unutilized potential resources for D-lactic acid production. These results indicate that MPF using L. mesenteroides and A. awamori could constitute part of a potential industrial application of the currently unutilized banana peel and corncob biomass for D-lactic acid production.

Demonstration of the production of oxygen-centered free radicals during electrolysis using E.S.R. spin-trapping techniques: effects on cardiac function in the isolated rat heart.

PubMed

Lecour, S; Baouali, A B; Maupoil, V; Chahine, R; Abadie, C; Javouhey-Donzel, A; Rochette, L; Nadeau, R

1998-03-01

The present study was designed to identify the free radicals generated during the electrolysis of the solution used to perfuse isolated rat heart Langendorff preparations. The high reactivity and very short half-life of oxygen free radicals make their detection and identification difficult. A diamagnetic organic molecule (spin trap) can be used to react with a specific radical to produce a more stable secondary radical or "spin adduct" detected by electron spin resonance (ESR). Isovolumic left ventricular systolic pressure (LVSP) and left ventricular end diastolic pressure (LVEDP) were measured by a fluid-filled latex balloon inserted into the left ventricle. The coronary flow was measured by effluent collection. Electrolysis was performed with constant currents of 0.5, 1, 1.5, 3, 5, 7.5, and 10 mA generated by a Grass stimulator and applied to the perfusion solution for 1 min. A group of experiments was done using a 1.5 mA current and a Krebs-Henseleit (K-H) solution containing free radical scavengers (superoxide dismutase (SOD): 100 IU/ml or mannitol: 50 mM). Heart function rapidly declined in hearts perfused with K-H buffer that had been electrolyzed for 1 min. The addition of mannitol (50 mM) to the perfusion solution had no effect on baseline cardiac function before electrolysis while SOD (100 IU/ml) increased the coronary flow. However, SOD was more effective than the mannitol in protecting the heart against decreased of cardiac function, 5 min after the end of electrolysis. Samples of the K-H medium subjected to electrolysis were collected in cuvettes containing a final concentration of 125 mM 5,5-dimethyl-1-pyrroline-N-oxide (DMPO) and analyzed by spectroscopy. The ESR spectrum consisted of a quartet signal (hyperfine couplings aN = aH = 14.9 G) originating from the hydroxyl adduct signal, DMPO-OH. The intensity of the DMPO-OH signal remained stable during the 60 s of electrolysis and the quantity of free radicals induced by electrolysis was directly proportional to the intensity of the current. The addition of mannitol and SOD to the perfusate scavenged the hydroxyl radicals present in the solution, suggesting that both hydroxyl and superoxide radicals were formed during electrolysis.

Dissimilar Arc Welding of Advanced High-Strength Car-Body Steel Sheets

NASA Astrophysics Data System (ADS)

Russo Spena, P.; D'Aiuto, F.; Matteis, P.; Scavino, G.

2014-11-01

A widespread usage of new advanced TWIP steel grades for the fabrication of car-body parts is conditional on the employment of appropriate welding methods, especially if dissimilar welding must be performed with other automotive steel grades. Therefore, the microstructural features and the mechanical response of dissimilar butt weld seams of TWIP and 22MnB5 steel sheets after metal-active-gas arc welding are examined. The microstructural and mechanical characterization of the welded joints was carried out by optical metallography, microhardness and tensile testing, and fractographic examination. The heat-affected zone on the TWIP side was fully austenitic and the only detectable effect was grain coarsening, while on the 22MnB5 side it exhibited newly formed martensite and tempered martensite. The welded tensile specimens exhibited a much larger deformation on the TWIP steel side than on the 22MnB5. The fracture generally occurred at the interface between the fusion zone and the heat-affected zones, with the fractures surfaces being predominantly ductile. The ultimate tensile strength of the butt joints was about 25% lower than that of the TWIP steel.

Myocardial adaption to HI(R)T in previously untrained men with a randomized, longitudinal cardiac MR imaging study (Physical adaptions in Untrained on Strength and Heart trial, PUSH-trial).

PubMed

Scharf, Michael; Oezdemir, Derya; Schmid, Axel; Kemmler, Wolfgang; von Stengel, Simon; May, Matthias S; Uder, Michael; Lell, Michael M

2017-01-01

Although musculoskeletal effects in resistance training are well described, little is known about structural and functional cardiac adaption in formerly untrained subjects. We prospectively evaluated whether short term high intensity (resistance) training (HI(R)T) induces detectable morphologic cardiac changes in previously untrained men in a randomized controlled magnetic resonance imaging (MRI) study. 80 untrained middle-aged men were randomly assigned to a HI(R)T-group (n = 40; 43.5±5.9 years) or an inactive control group (n = 40; 42.0±6.3 years). HI(R)T comprised 22 weeks of training focusing on a single-set to failure protocol in 2-3 sessions/week, each with 10-13 exercises addressing main muscle groups. Repetitions were decreased from 8-10 to 3-5 during study period. Before and after HI(R)T all subjects underwent physiologic examination and cardiac MRI (cine imaging, tagging). Indexed left (LV) and right ventricular (RV) volume (LV: 76.8±15.6 to 78.7±14.8 ml/m2; RV: 77.0±15.5 to 78.7±15.1 ml/m2) and mass (LV: 55.5±9.7 to 57.0±8.8 g/m2; RV: 14.6±3.0 to 15.0±2.9 g/m2) significantly increased with HI(R)T (all p<0.001). Mean LV and RV remodeling indices of HI(R)T-group did not alter with training (0.73g/mL and 0.19g/mL, respectively [p = 0.96 and p = 0.87]), indicating balanced cardiac adaption. Indexed LV (48.4±11.1 to 50.8±11.0 ml/m2) and RV (48.5±11.0 to 50.6±10.7 ml/m2) stroke volume significantly increased with HI(R)T (p<0.001). Myocardial strain and strain rates did not change following resistance exercise. Left atrial volume at end systole slightly increased after HI(R)T (36.2±7.9 to 37.0±8.4 ml/m2, p = 0.411), the ratio to end-diastolic LV volume at baseline and post-training was unchanged (0.47 vs. 0.47, p = 0.79). 22 weeks of HI(R)T lead to measurable, physiological changes in cardiac atrial and ventricular morphologic characteristics and function in previously untrained men. The PUSH-trial is registered at the US National Institutes of Health (ClinicalTrials.gov), NCT01766791.

Advanced Battery Management Challenges for Military Vehicles

DTIC Science & Technology

2013-12-06

NCA, NCM) 2.5-4.1 7.5-12.3 10-16.4 15-24.6 17.5-28.7 20-32.8 L F P Nominal Voltage(V) ( LiFePO4 ) 3.3 9.9 13.2 19.8 23.1 26.4 n x 3.3 Voltage range...V) ( LiFePO4 ) 2.0-3.7 6-11.1 8-14.8 12-22.2 14-25.9 16-29.6 15 12V 6T 24V 6T UNCLASSIFIED Advanced Chemistry BMS • Required for Li-ion

Tribological properties of CrN coatings deposited by nitro-chromizing treatment on AISI D2 steel

NASA Astrophysics Data System (ADS)

Durmaz, M.; Kilinc, B.; Abakay, E.; Sen, U.; Sen, S.

2015-03-01

In this work, the wear test of uncoated and chromium nitride coated AISI D2 cold work tool steel against alumina ball realized at 0.1 m/s sliding speeds and under the loads of 2.5N, 5N and 10N. Steel samples were nitrided at 575°C for 8 h in the first step of the coating process, and then chromium nitride coating was performed thermo-reactive deposition technique (TRD) in a powder mixture consisting of ferro-chromium, ammonium chloride and alumina at 1000°C for 2 h. Nitro-chromized samples were characterized by X-Ray diffraction analysis (XRD), scanning electron microscopy (SEM), micro-hardness and ball on disk wear tests. The coating layer formed on the AISI D2 steel was compact and homogeneous. X-ray studies showed that the phase formed in the coated layer is Cr2N. The depth of the layer was 8.15 µm. The average hardness of the layer was 2160±15 HV0.025. For uncoated and chromium nitride materials, wear rate increased with increasing load. The results of friction coefficient and wear rate of the tested materials showed that the CrN coating presents the lowest results.

Tribological properties of CrN coatings deposited by nitro-chromizing treatment on AISI D2 steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Durmaz, M., E-mail: mdurmaz@sakarya.edu.tr; Abakay, E.; Sen, U.

2015-03-30

In this work, the wear test of uncoated and chromium nitride coated AISI D2 cold work tool steel against alumina ball realized at 0.1 m/s sliding speeds and under the loads of 2.5N, 5N and 10N. Steel samples were nitrided at 575°C for 8 h in the first step of the coating process, and then chromium nitride coating was performed thermo-reactive deposition technique (TRD) in a powder mixture consisting of ferro-chromium, ammonium chloride and alumina at 1000°C for 2 h. Nitro-chromized samples were characterized by X-Ray diffraction analysis (XRD), scanning electron microscopy (SEM), micro-hardness and ball on disk wear tests. The coating layermore » formed on the AISI D2 steel was compact and homogeneous. X-ray studies showed that the phase formed in the coated layer is Cr{sub 2}N. The depth of the layer was 8.15 µm. The average hardness of the layer was 2160±15 HV{sub 0.025}. For uncoated and chromium nitride materials, wear rate increased with increasing load. The results of friction coefficient and wear rate of the tested materials showed that the CrN coating presents the lowest results.« less

Atmospheric fates of Criegee intermediates in the ozonolysis of isoprene.

PubMed

Nguyen, Tran B; Tyndall, Geoffrey S; Crounse, John D; Teng, Alexander P; Bates, Kelvin H; Schwantes, Rebecca H; Coggon, Matthew M; Zhang, Li; Feiner, Philip; Milller, David O; Skog, Kate M; Rivera-Rios, Jean C; Dorris, Matthew; Olson, Kevin F; Koss, Abigail; Wild, Robert J; Brown, Steven S; Goldstein, Allen H; de Gouw, Joost A; Brune, William H; Keutsch, Frank N; Seinfeld, John H; Wennberg, Paul O

2016-04-21

We use a large laboratory, modeling, and field dataset to investigate the isoprene + O3 reaction, with the goal of better understanding the fates of the C1 and C4 Criegee intermediates in the atmosphere. Although ozonolysis can produce several distinct Criegee intermediates, the C1 stabilized Criegee (CH2OO, 61 ± 9%) is the only one observed to react bimolecularly. We suggest that the C4 Criegees have a low stabilization fraction and propose pathways for their decomposition. Both prompt and non-prompt reactions are important in the production of OH (28% ± 5%) and formaldehyde (81% ± 16%). The yields of unimolecular products (OH, formaldehyde, methacrolein (42 ± 6%) and methyl vinyl ketone (18 ± 6%)) are fairly insensitive to water, i.e., changes in yields in response to water vapor (≤4% absolute) are within the error of the analysis. We propose a comprehensive reaction mechanism that can be incorporated into atmospheric models, which reproduces laboratory data over a wide range of relative humidities. The mechanism proposes that CH2OO + H2O (k(H2O)∼ 1 × 10(-15) cm(3) molec(-1) s(-1)) yields 73% hydroxymethyl hydroperoxide (HMHP), 6% formaldehyde + H2O2, and 21% formic acid + H2O; and CH2OO + (H2O)2 (k(H2O)2∼ 1 × 10(-12) cm(3) molec(-1) s(-1)) yields 40% HMHP, 6% formaldehyde + H2O2, and 54% formic acid + H2O. Competitive rate determinations (kSO2/k(H2O)n=1,2∼ 2.2 (±0.3) × 10(4)) and field observations suggest that water vapor is a sink for greater than 98% of CH2OO in a Southeastern US forest, even during pollution episodes ([SO2] ∼ 10 ppb). The importance of the CH2OO + (H2O)n reaction is demonstrated by high HMHP mixing ratios observed over the forest canopy. We find that CH2OO does not substantially affect the lifetime of SO2 or HCOOH in the Southeast US, e.g., CH2OO + SO2 reaction is a minor contribution (<6%) to sulfate formation. Extrapolating, these results imply that sulfate production by stabilized Criegees is likely unimportant in regions dominated by the reactivity of ozone with isoprene. In contrast, hydroperoxide, organic acid, and formaldehyde formation from isoprene ozonolysis in those areas may be significant.

Causal Neuro-immune Relationships at Patients with Chronic Pyelonephritis and Cholecystitis. Correlations between Parameters EEG, HRV and White Blood Cell Count.

PubMed

Kul'chyns'kyi, Andriy B; Kyjenko, Valeriy M; Zukow, Walery; Popovych, Igor L

2017-01-01

We aim to analyze in bounds KJ Tracey's immunological homunculus conception the relationships between parameters of electroencephalogram (EEG) and heart rate variability (HRV), on the one hand, and the parameters of bhite blood cell count, on the other hand. In basal conditions in 23 men, patients with chronic pyelonephritis and cholecystitis in remission, recorded EEG ("NeuroCom Standard", KhAI Medica, Ukraine) and HRV ("Cardiolab+VSR", KhAI Medica, Ukraine). In portion of blood counted up white blood cell count. Revealed that canonical correlation between constellation EEG and HRV parameters form with blood level of leukocytes 0.92 (p<10-5), with relative content in white blood cell count stubnuclear neutrophiles 0.93 (p<10-5), segmentonucleary neutrophiles 0.89 (p<10-3), eosinophiles 0.87 (p=0.003), lymphocytes 0.77 (p<10-3) and with monocytes 0.75 (p=0.003). Parameters of white blood cell count significantly modulated by electrical activity some structures of central and autonomic nervous systems.

The effect of natural and anthropogenic factors on sorption of copper in chernozem

NASA Astrophysics Data System (ADS)

Bauer, Tatiana; Minkina, Tatiana; Mandzhieva, Saglara; Pinskii, David; Linnik, Vitaly; Sushkova, Svetlana

2016-04-01

The aim of this work was to study the effect of the attendant anions and particle-size distribution on the adsorption of copper by ordinary chernozem. Solutions of HM nitrates, acetates, chlorides, and sulfates were used to study the effect of the chemical composition of added copper salts on the adsorption of copper by an ordinary chernozem. Samples of the soil sieved through a 1-mm sieve in the natural ionic form and soil fraction with different particle size (clay - the particle with size < 1μm and physical clay < 10 μm) were treated with solutions of the corresponding copper salts at a soil : solution ratio of 1:10. The concentrations of the initial copper solutions were 0.02, 0.05, 0.08, 0.1, 0.3, 0.5, and 1.0 mM/L. The range of Cu2+ concentrations in the studied system covers different geochemical situations corresponding to the actual levels of soil contamination with the metal under study. The suspensions were shaken for 1 h, left to stand for 24 h, and then filtered. The contents of the HM in the filtrates were determined by atomic absorption spectrometry (AAS). The contents of the adsorbed copper cations were calculated from the difference between the metal concentrations in the initial and equilibrium solutions. The isotherms of copper adsorption from the metal nitrate, chloride, and sulfate solutions have near linear shapes and, hence, can be satisfactorily described by a Henry or Freundlich equation: Cads = KH •Ceq.(1) Cads = KF •Ceqn,(2) where Cadsis the content of the adsorbed cations, mM/kg soil;Ceq is the concentration of copper in the equilibrium solution, mM/L; KH and KF denote the Henry and Freundlich adsorption coefficients, respectively, kg/L. The isotherm of Cu2+ adsorption by ordinary chernozem from acetate solutions is described by the Langmuir equation: Cads = C∞ÊLC / (1 + ÊLC), (3) where Cadsis the content of the adsorbed cations, mM/kg soil;C∞ is the maximum adsorption of the HM, mM/kg soil; ÊL is the affinity constant, L/mM; C is the concentration of the HM in the equilibrium solution, mM/L. According to the values of KH, the binding strength of the copper cations adsorbed from different salt solutions decreases in the series: Cu(Ac)2(1880,5± 76,2) > CuCl2(1442,8±113,5) > Cu(NO3)2(911,4 ± 31,1) >> CuSO4(165,3 ± 12,9). Thus, copper is most strongly adsorbed from the acetate solution and least strongly from the sulfate solution. The adsorption of copper by clay and physical clay fractions from the ordinary chernozem was of limited character and followed the (3) equation. In the particle-size fractions separated from the soils, the concentrations of copper decreased with the decreasing particle size. The values of ÊL and C∞characterizing the HM adsorption by the chernozem and its particle-size fractions formed the following sequence: clay (80,20±20,29 and 28,45±0,46 > physical clay (58,20±14,54 and 22,15±1,22) > entire soil (38,80±12,33 and 17,58±3,038). This work was supported by the Russian Ministry of Education and Science, project no. 5.885.2014/K, Russian Foundation for Basic Research, projects no. 14-05-00586 À

In-plane electrical transport in n-type selectively doped GaSb/AlGaSb multiquantum wells

NASA Astrophysics Data System (ADS)

Ghezzi, C.; Cioce, B.; Magnanini, R.; Parisini, A.

2001-11-01

Results are reported regarding in-plane electrical transport in n-type selectively doped GaSb/AlGaSb multiquantum wells. In the samples, which were grown by molecular beam epitaxy, only the central regions of the Al0.40Ga0.60Sb barriers were Te doped. Low-field, low-temperature Hall measurements in the dark demonstrated the presence in the GaSb wells of a degenerate electron gas with nonzero occupancy only for the lowest miniband. A positive persistent photoconductivity effect, related to the DX character of the Te impurity, was also observed. This behavior enabled the μ electron mobility to be measured at T=10 K as a function of the nS sheet carrier density. Since the experimental data were consistent with a dominant role of the interface roughness scattering in the limiting of μ, the height, Δ, and the lateral size, Λ, of the interface roughness were determined from the analysis of the μ=μ(nS) dependence. Acceptable values of Δ were obtained, consistent with results of structural investigations in single quantum well samples of GaSb/Al0.40Ga0.60Sb [E. Kh. Mukhamedzhanov, C. Bocchi, S. Franchi, A. Baraldi, R. Magnanini, and L. Nasi, J. Appl. Phys. 87, 4234 (2000)].

High Temperature Strengthening in 12Cr-W-Mo Steels by Controlling the Formation of Delta Ferrite

NASA Astrophysics Data System (ADS)

Wang, Shushen; Chang, Li; Lin, Deye; Chen, Xiaohua; Hui, Xidong

2014-09-01

Novel 12Cr-W-Mo-Co heat resistance steels (HRSs) with excellent mechanical properties have been developed for ultra-supercritical (USC) applications above 923 K (650 °C). The thermal analysis of the present steels indicates that the remelting temperature of secondary phases is increased by Co alloying, resulting in the improvement of microstructural stability. Delta ferrite in these HRSs is completely suppressed as the content of Co is increased up to 5 pct. The room temperature tensile strength (TS), yield strength (YS), and the elongation (EL) of the HRS with 5 pct Co reach 887.9, 652.6 MPa, and 21.07 pct, respectively. At 948 K (675 °C), the TS and YS of the HRS with 5 pct Co attain 360 and 290 MPa, respectively, which are higher than those of T/P122 steel by 27.4 and 22.1 pct, respectively. TEM study of the microstructure confirmed that the strengthening effects for these 12Cr-W-Mo-Co HRSs are attributed to the suppression of delta ferrite, the formation of fine martensitic laths with substructure, dislocation networks and walls, and the precipitation of second nanoscale phases.

Reliability of MRSI brain temperature mapping at 1.5 and 3 T.

PubMed

Thrippleton, Michael J; Parikh, Jehill; Harris, Bridget A; Hammer, Steven J; Semple, Scott I K; Andrews, Peter J D; Wardlaw, Joanna M; Marshall, Ian

2014-02-01

MRSI permits the non-invasive mapping of brain temperature in vivo, but information regarding its reliability is lacking. We obtained MRSI data from 31 healthy male volunteers [age range, 22-40 years; mean ± standard deviation (SD), 30.5 ± 5.0 years]. Eleven subjects (age range, 23-40 years; mean ± SD, 30.5 ± 5.2 years) were invited to receive four point-resolved spectroscopy MRSI scans on each of 3 days in both 1.5-T (TR/TE = 1000/144 ms) and 3-T (TR/TE = 1700/144 ms) clinical scanners; a further 20 subjects (age range, 22-40 years; mean ± SD, 30.5 ± 4.9 years) were scanned on a single occasion at 3 T. Data were fitted in the time domain to determine the water-N-acetylaspartate chemical shift difference, from which the temperature was estimated. Temperature data were analysed using a linear mixed effects model to determine variance components and systematic temperature changes during the scanning sessions. To characterise the effects of instrumental drift on apparent MRSI brain temperature, a temperature-controlled phantom was constructed and scanned on multiple occasions. Components of apparent in vivo temperature variability at 1.5 T/3 T caused by inter-subject (0.18/0.17 °C), inter-session (0.18/0.15 °C) and within-session (0.36/0.14 °C) effects, as well as voxel-to-voxel variation (0.59/0.54 °C), were determined. There was a brain cooling effect during in vivo MRSI of 0.10 °C [95% confidence interval (CI): -0.110, -0.094 °C; p < 0.001] and 0.051 °C (95% CI: -0.054, -0.048 °C; p < 0.001) per scan at 1.5 T and 3 T, respectively, whereas phantom measurements revealed minimal drift in apparent MRSI temperature relative to fibre-optic temperature measurements. The mean brain temperature at 3 T was weakly associated with aural (R = 0.55, p = 0.002) and oral (R = 0.62, p < 0.001) measurements of head temperature. In conclusion, the variability associated with MRSI brain temperature mapping was quantified. Repeatability was somewhat higher at 3 T than at 1.5 T, although subtle spatial and temporal variations in apparent temperature were demonstrated at both field strengths. Such data should assist in the efficient design of future clinical studies. © 2013 The Authors. NMR in Biomedicine published by John Wiley & Sons, Ltd.

Austenitic stainless steel for high temperature applications

DOEpatents

Johnson, Gerald D.; Powell, Roger W.

1985-01-01

This invention describes a composition for an austenitic stainless steel which has been found to exhibit improved high temperature stress rupture properties. The composition of this alloy is about (in wt. %): 12.5 to 14.5 Cr; 14.5 to 16.5 Ni; 1.5 to 2.5 Mo; 1.5 to 2.5 Mn; 0.1 to 0.4 Ti; 0.02 to 0.08 C; 0.5 to 1.0 Si; 0.01 maximum, N; 0.02 to 0.08 P; 0.002 to 0.008 B; 0.004-0.010 S; 0.02-0.05 Nb; 0.01-0.05 V; 0.005-0.02 Ta; 0.02-0.05 Al; 0.01-0.04 Cu; 0.02-0.05 Co; 0.03 maximum, As; 0.01 maximum, O; 0.01 maximum, Zr; and with the balance of the alloy being essentially iron. The carbon content of the alloy is adjusted such that wt. % Ti/(wt. % C+wt. % N) is between 4 and 6, and most preferably about 5. In addition the sum of the wt. % P+wt. % B+wt. % S is at least 0.03 wt. %. This alloy is believed to be particularly well suited for use as fast breeder reactor fuel element cladding.

Cape Newenham AFS, Alaska. Revised Uniform Summary of Surface Weather Observations (RUSSWO). Parts A-F.

DTIC Science & Technology

1983-04-01

OBSERVATIONS) L P- 14 H~N A A-F S .~ 73-F2 ____ JA&,. ALL WI- LAt E -- .. - - 6 7 0 11 16 17 21 22 27 28- 33 34 *0 41 A7 48 5 .7 * . .3 .4 .4 . 1 . i E...PERCENTAGE FREQUENCY OF WIND DIRECTION AND SPEED (FROM HOURLY OBSERVATIONS) 4LL . LAT -E- - 10 1 1 i 7 23 22 ’ 2 3 3 A 40 A 3 5 A7 A • ’ .. 5 .t",5...SCOTT A. APR 03 UNCLASSIFIED USAFETAC/DS-83/019 SBI-AD-EB50 397 F/6 4/2 NL SU 2. lii .0 EM *,*,- Ica L- 11111 1.25 s~w ,r- 1 . 11.6 I MiCRQ OPY

Application of liquid-liquid-liquid microextraction and high-performance liquid chromatography for the determination of alkylphenols and bisphenol-A in water.

PubMed

Lin, Che-Yi; Fuh, Ming-Ren; Huang, Shang-Da

2011-02-01

A method termed liquid-liquid-liquid microextraction (LLLME) was utilized to extract 4-t-butylphenol, 4-t-octylphenol, 4-n-nonylphenol, and bisphenol-A from water. The extracted target analytes were separated and quantified by high-performance liquid chromatography using a fluorescence detector. In LLLME, the donor phase (i.e. water sample) was made weakly acidic by adding monobasic potassium phosphate (KH(2) PO(4)); the organic phase adopted was 4-chlorotoluene; the acceptor phase (i.e. enriched extract) was 0.2 M tetraethylammonium hydroxide dissolved in ethylene glycol. This study solves a problem associated with the surface activity of long-chain alkylphenolate ions, permitting LLLME to extract long-chain alkylphenols. Experimental conditions such as acceptor phase composition, organic phase identity, acceptor phase volume, sample agitation, extraction time, and salt addition were optimized. The relative standard deviation (RSD, 2.0-5.8%), coefficient of determination (r(2) 0.9977-0.9999), and detection limit (0.017-0.0048 ng/mL) of the proposed method were achieved under the selected optimized conditions. The method was successfully applied to analyses of lake and tap water samples, and the relative recoveries of target analytes from the spiked lake and tap water samples were 92.8-106.3 and 93.6-105.6%, respectively. The results obtained with the proposed method confirm this microextraction technique to be reliable for the monitoring of alkylphenols and bisphenol-A in water samples. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

[Simultaneous determination of four common nonprotein nitrogen substances in urine by high performance liquid chromatography].

PubMed

Ma, Yuhua; Huang, Dongqun; Zhang, Rui; Xu, Shiru; Feng, Shun

2013-11-01

A high performance liquid chromatographic (HPLC) method was proposed to simultaneously determine four common nonprotein nitrogen substances, including creatine (Cr), creatinine (Cn), uric acid (Ua) and pseudouridine (Pu) in urine. After proteins being removed by acetone precipitation method, freeze drying and redissolving, the urine samples were analyzed by HPLC. Chromatographic separation was performed on a Waters RP18 Column (150 mm x 4.60 mm, 3.5 microm) in gradient elution mode using 10.0 mmol/L KH2PO4 solution (pH 4.78) and acetonitrile as mobile phases at a flow rate of 0.8 mL/min. The samples were detected at 220 nm. Rapid separation was achieved within 7 min. Under the optimized conditions, good linearities of four common nonprotein nitrogen substances were obtained in the range of 0.1-250 mg/L. The detection limits were 9.31 (Cr), 26.19 (Cn), 4.70 (Ua), an 6.30 (Pu) microg/L and the recoveries were in the range of 81%-111% with the relative standar deviations of 0.23%-2.78% (n = 3). The results demonstrate that this method is simple, rapid and accurate with good reproducibility, and can provide early diagnosis and preliminary judgment for type 2 diabetes mellitus (T2DM) patients with renal damage.

Reducing soil erosion and nutrient loss on sloping land under crop-mulberry management system.

PubMed

Fan, Fangling; Xie, Deti; Wei, Chaofu; Ni, Jiupai; Yang, John; Tang, Zhenya; Zhou, Chuan

2015-09-01

Sloping croplands could result in soil erosion, which leads to non-point source pollution of the aquatic system in the Three Gorges Reservoir Region. Mulberry, a commonly grown cash plant in the region, is traditionally planted in contour hedgerows as an effective management practice to control soil erosion and non-point source pollution. In this field study, surface runoff and soil N and P loss on sloping land under crop-mulberry management were investigated. The experiments consisted of six crop-mulberry treatments: Control (no mulberry hedgerow with mustard-corn rotation); T1 (two-row contour mulberry with mustard-corn rotation); T2 (three-row contour mulberry with mustard-corn rotation); T3 (border mulberry and one-row contour mulberry with mustard-corn rotation); T4 (border mulberry with mustard-corn rotation); T5 (two-row longitudinal mulberry with mustard). The results indicated that crop-mulberry systems could effectively reduce surface runoff and soil and nutrient loss from arable slope land. Surface runoff from T1 (342.13 m(3) hm(-2)), T2 (260.6 m(3) hm(-2)), T3 (113.13 m(3) hm(-2)), T4 (114 m(3) hm(-2)), and T5 (129 m(3) hm(-2)) was reduced by 15.4, 35.6, 72.0, 71.8, and 68.1%, respectively, while soil loss from T1 (0.21 t hm(-2)), T2 (0.13 t hm(-2)), T3 (0.08 t hm(-2)), T4 (0.11 t hm(-2)), and T5 (0.12 t hm(-2)) was reduced by 52.3, 70.5, 81.8, 75.0, and 72.7%, respectively, as compared with the control. Crop-mulberry ecosystem would also elevate soil N by 22.3% and soil P by 57.4%, and soil nutrient status was contour-line dependent.

D816 mutation of the KIT gene in core binding factor acute myeloid leukemia is associated with poorer prognosis than other KIT gene mutations.

PubMed

Yui, Shunsuke; Kurosawa, Saiko; Yamaguchi, Hiroki; Kanamori, Heiwa; Ueki, Toshimitsu; Uoshima, Nobuhiko; Mizuno, Ishikazu; Shono, Katsuhiro; Usuki, Kensuke; Chiba, Shigeru; Nakamura, Yukinori; Yanada, Masamitsu; Kanda, Junya; Tajika, Kenji; Gomi, Seiji; Fukunaga, Keiko; Wakita, Satoshi; Ryotokuji, Takeshi; Fukuda, Takahiro; Inokuchi, Koiti

2017-10-01

The clinical impact of KIT mutations in core binding factor acute myeloid leukemia (CBF-AML) is still unclear. In the present study, we analyzed the prognostic significance of each KIT mutation (D816, N822K, and other mutations) in Japanese patients with CBF-AML. We retrospectively analyzed 136 cases of CBF-AML that had gone into complete remission (CR). KIT mutations were found in 61 (45%) of the patients with CBF-AML. D816, N822K, D816 and N822K, and other mutations of the KIT gene were detected in 29 cases (21%), 20 cases (15%), 7 cases (5%), and 5 cases (4%), respectively. The rate of relapse-free survival (RFS) and overall survival (OS) in patients with D816 and with both D816 and N822K mutations was significantly lower than in patients with other or with no KIT mutations (RFS: p < 0.001, OS: p < 0.001). Moreover, stratified analysis of the chromosomal abnormalities t(8;21)(q22;q22) and inv(16)(p13.1q22), t(16;16)(p13.1;q22) showed that D816 mutation was associated with a significantly worse prognosis. In a further multivariate analysis of RFS and OS, D816 mutation was found to be an independent risk factor for significantly poorer prognosis. In the present study, we were able to establish that, of all KIT mutations, D816 mutation alone is an unfavorable prognostic factor.

Changes in microbial biomass and P fractions in biogenic household waste compost amended with inorganic P fertilizers.

PubMed

Khan, Khalid Saifullah; Joergensen, Rainer Georg

2009-01-01

The present study was conducted to evaluate the changes in microbial biomass indices (C, N, and especially P) and in P fractions in compost amended with inorganic P fertilizers. In the non-amended control, the average contents of microbial biomass C, N, and P were 1744, 193, and 63 microg g(-1) compost, respectively. On average, 1.3% of total P was stored as microbial biomass P. The addition of KH(2)PO(4) and TSP (triple super phosphate) led to immediate significant increases in microbial biomass C, N, and P. Approximately, 4.6% of the added TSP and 5.8% of the added KH(2)PO(4) were incorporated on average into the microbial biomass throughout the incubation. Approximately, 4.7% of the 1mg and 5.8% of the 2mg addition rate were incorporated on average into the microbial biomass. In the amendment treatments, the average contents of microbial biomass C, N, and P declined by 44%, 64%, and 49%, respectively. Initially, the average size of the P fractions in the non-amended compost increased in the order (% of total P in brackets) resin P (0.7%)

Thermophysical Property Measurements of Liquid Gadolinium by Containerless Methods

NASA Astrophysics Data System (ADS)

Ishikawa, T.; Okada, J. T.; Paradis, P.-F.; Watanabe, Y.

2010-02-01

Thermophysical properties of liquid gadolinium were measured using non-contact diagnostic techniques with an electrostatic levitator. Over the 1585 K to 1920 K temperature range, the density can be expressed as ρ( T) = 7.41 × 103 - 0.46 ( T - T m) (kg · m-3) where T m = 1585 K, yielding a volume expansion coefficient of 6.2 × 10-5 K-1. In addition, the surface tension data can be fitted as γ( T) = 8.22 × 102 - 0.097( T - T m)(10-3 N · m-1) over the 1613 K to 1803 K span and the viscosity as η( T) = 1.7exp[1.4 × 104/( RT)](10-3 Pa · s) over the same temperature range.

The Dependence of Heat and Gas Transfer Velocities on Wind-Generated and Mechanically Generated Aqueous-Phase Turbulence

NASA Astrophysics Data System (ADS)

Liang, H.; Mukto, M.; Loewen, M.; Zappa, C.; Litchendorf, T.; Asher, W.; Jessup, A.

2006-12-01

The air-sea flux, F, of a sparingly soluble nonreactive gas can be expressed as F = kG( CS-CW), where kG is the gas transfer velocity, CS is the concentration of gas that would be expected in the water if the system were in Henry`s Gas Law equilibrium, and CW is the actual concentration of the gas in the water. An analogous relationship for the net heat flux can also be written using the heat transfer velocity, kH, and the bulk-skin temperature difference in the aqueous phase. Hydrodynamical models of gas and heat exchange based on surface renewal theory predict that kG and kH will scale as the square root of the inverse of a timescale of the turbulence. Furthermore, if surface renewal provides an accurate conceptual model for both transfer processes, then both kG and kH should behave identically as turbulence conditions change. Here we report on recent laboratory experiments in which we measured turbulence, heat fluxes, kG, and kH in a 0.5 m by 0.5 m by 1 m deep tank in the presence of turbulence generated mechanically using a random synthetic jet array. The turbulence tank was embedded in a small wind tunnel so that kG and kH could be studied as a function of the mechanically generated turbulence but also turbulence generated by wind stress. Net heat transfer velocities were measured using Active Controlled Flux Technique and estimated from measurements of the latent and sensible heat fluxes combined with direct measurements of the bulk-skin temperature difference. Gas transfer velocities were determined by measuring the evasion rates of sulfur hexafluoride and helium. The length and velocity scales of the aqueous-phase turbulence were measured using a Digital Particle-Image Velocimetry system. These combined data sets are used to study how kG and kH depend on system turbulence, whether this dependence is consonant with that predicted using surface renewal, and whether there is a quantitative difference between mechanically generated turbulence and turbulence generated by the wind stress insofar as air-water exchange is concerned.

Influence of 5,10-methylenetetrahydrofolate reductase polymorphism on whole-blood folate concentrations measured by LC-MS/MS, microbiologic assay, and bio-rad radioassay.

PubMed

Fazili, Zia; Pfeiffer, Christine M; Zhang, Mindy; Jain, Ram B; Koontz, Deborah

2008-01-01

The 5,10-methylenetetrahydrofolate reductase (NADPH) (MTHFR) C677T polymorphism may affect whole-blood folate pattern measured by liquid chromatography-tandem mass spectrometry (LC-MS/MS) and total folate measured by LC-MS/MS, microbiologic assay, and Bio-Rad radioassay (BR). We analyzed 171 whole blood hemolysates from 2 blood banks for folate pattern and total folate concentrations using these 3 methods and determined MTHFR genotype. The median (range) total folate concentration by LC-MS/MS was higher in the US set [378 (228-820) nmol/L; n = 96] than in the European set [250 (122-582) nmol/L; n = 75]. The whole-blood folate pattern [median (range)] was similar for individuals with C/C (n = 73) and C/T (n = 66) genotype: 88% (71%-91%) and 86% (50%-91%), respectively, for 5-methyltetrahydrofolic acid (5CH(3)THF) vs 12% (9%-29%) and 14% (9%-51%) for forms other than 5-methyltetrahydrofolic acid (non-5CH(3)THF). Individuals with T/T (n = 32) genotype had 58% (22%-87%) 5CH(3)THF vs 42% (13%-78%) non-5CH(3)THF. Compared with microbiologic assay results, LC-MS/MS (r = 0.94) and BR (r = 0.87) results were significantly lower (-10% and -45%, respectively); however, these differences were concentration dependent and also genotype dependent for the BR assay (-48% for C/C+C/T and -31% for T/T). The microbiologic assay completely recovered [mean (SD)] folates added to a whole blood hemolysate, except for tetrahydrofolic acid (THF) [46.4% (8.1%)]. The BR assay under-recovered 5CH(3)THF [51% (4.1%)] and 5-formyltetrahydrofolic acid [18% (0.1%)], and over-recovered THF [152% (19%)]. MTHFR C677T polymorphism influences the folate pattern in whole blood. The agreement between total folate by LC-MS/MS and microbiologic assay, independent of the MTHFR genotype, allows the use of one regression equation. Because BR results are genotype dependent, different regression equations should be used.

Radiographic liver size in Pekingese dogs versus other dog breeds.

PubMed

Choi, Jihye; Keh, Seoyeon; Kim, Hyunwook; Kim, Junyoung; Yoon, Junghee

2013-01-01

Differential diagnoses for canine liver disease are commonly based on radiographic estimates of liver size, however little has been published on breed variations. Aims of this study were to describe normal radiographic liver size in Pekingese dogs and to compare normal measurements for this breed with other dog breeds and Pekingese dogs with liver disease. Liver measurements were compared for clinically normal Pekingese (n = 61), normal non-Pekingese brachycephalic (n = 45), normal nonbrachycephalic (n = 71), and Pekingese breed dogs with liver disease (n = 22). For each dog, body weight, liver length, T11 vertebral length, thoracic depth, and thoracic width were measured on right lateral and ventrodorsal abdominal radiographs. Liver volume was calculated using a formula and ratios of liver length/T11 vertebral length and liver volume/body weight ratio were determined. Normal Pekingese dogs had a significantly smaller liver volume/body weight ratio (16.73 ± 5.67, P < 0.05) than normal non-Pekingese brachycephalic breed dogs (19.54 ± 5.03) and normal nonbrachycephalic breed dogs (18.72 ± 6.52). The liver length/T11 vertebral length ratio in normal Pekingese (4.64 ± 0.65) was significantly smaller than normal non-Pekingese brachycephalic breed dogs (5.16 ± 0.74) and normal nonbrachycephalic breed dogs (5.40 ± 0.74). Ratios of liver volume/body weight and liver length/T11 vertebral length in normal Pekingese were significantly different from Pekingese with liver diseases (P < 0.05). Findings supported our hypothesis that Pekingese dogs have a smaller normal radiographic liver size than other breeds. We recommend using 4.64× the length of the T11 vertebra as a radiographic criterion for normal liver length in Pekingese dogs. © 2012 Veterinary Radiology & Ultrasound.

Micro-Raman observation on the H2PO4- association structures in a supersaturated droplet of potassium dihydrogen phosphate (KH2PO4)

NASA Astrophysics Data System (ADS)

Syed, Kamran Ajmal; Pang, Shu-Feng; Zhang, Yun; Zhang, Yun-Hong

2013-01-01

The efflorescence of an individual KH2PO4 droplet on Teflon substrate was investigated by micro-Raman spectroscopy. With the decrease of relative humidity (RH) from 98.0% to 73.0%, the KH2PO4 droplet lost water gradually and entered into supersaturated state, which was reflected by the area ratio between the water stretching band to the sum of νs-PO2 and νs-P(OH)2 bands of the H2PO4- (A_{H_2 O} /(A_{(ν _s -PO_2 } {+ A}_{ν _s -P(OH)_2 {)}} {)}). In 1.0 mol l-1 KH2PO4 solution, the νs-P(OH)2 and νs-PO2 bands appeared at 877 and 1077 cm-1. In the KH2PO4 droplet, the two bands shifted to 894 and 1039 cm-1 at 98.0% RH, to 899 and 1031 cm-1 at 89.6% RH, and then to 904 and 997 cm-1 at 73.0% RH. Moreover, the aggregation process between the H2PO4- ions was observed from the spectral characteristic of the νs-P(OH)2 band in the concentration process, including the transitions of the H2PO4- ions from monomer in bulk solutions (0.5-1.0 mol l-1) to possible dimers at 98.0% RH and then further to oligomers in the droplet with the RH decrease, which were indicated by the blueshift of the νs-P(OH)2 band and its full width at half-height as a function of the RH. When the RH reached at 72.0%, the anhydrous crystal was obtained. A strong peak appeared at 928 cm-1, implying that the four oxygen atoms of the H2PO4- were all hydrogen bonding through the bridge hydrogen atoms to get the extensive hydrogen-bonded network structure of the H2PO4- association, leading to the symmetric increase of the H2PO4- ion from C2v in dilute solution to quasi-Td in the anhydrous crystal.

78 FR 79667 - Stainless Steel Sheet and Strip in Coils From Japan: Initiation of Expedited Changed...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-31

... weight, phosphorus of 0.025 percent or less, silicon of between 0.20 and 0.50 percent, and sulfur of 0... 19 and 22 percent, aluminum of no less than 5.0 percent, phosphorus of no more than 0.045 percent..., manganese, silicon and molybdenum each comprise, by weight, 0.05 percent or less, with phosphorus and sulfur...

Modeling Complex Nonlinear Optical Systems

DTIC Science & Technology

2006-07-01

L .k cycycyT kzk kzkkVxV kzkxTzVzTxVV ω β ββ κ 3 trapping cases (GS: ω(v=0) ≈ 0.96) |),,0(| tzxE =+ 2. Trapping into one defect...sech1 2 1 ),(sech2 where ),1)((tanh1 ),5;()()5;()( 22 222 2 22 1 22 21 . ., ., ., .- .k cycycyT kzk kzkkVxV kzkxTzVzTxVV L

An arsenate-reducing and alkane-metabolizing novel bacterium, Rhizobium arsenicireducens sp. nov., isolated from arsenic-rich groundwater.

PubMed

Mohapatra, Balaram; Sarkar, Angana; Joshi, Swati; Chatterjee, Atrayee; Kazy, Sufia Khannam; Maiti, Mrinal Kumar; Satyanarayana, Tulasi; Sar, Pinaki

2017-03-01

A novel arsenic (As)-resistant, arsenate-respiring, alkane-metabolizing bacterium KAs 5-22 T , isolated from As-rich groundwater of West Bengal was characterized by physiological and genomic properties. Cells of strain KAs 5-22 T were Gram-stain-negative, rod-shaped, motile, and facultative anaerobic. Growth occurred at optimum of pH 6.0-7.0, temperature 30 °C. 16S rRNA gene affiliated the strain KAs 5-22 T to the genus Rhizobium showing maximum similarity (98.4 %) with the type strain of Rhizobium naphthalenivorans TSY03b T followed by (98.0 % similarity) Rhizobium selenitireducens B1 T . The genomic G + C content was 59.4 mol%, and DNA-DNA relatedness with its closest phylogenetic neighbors was 50.2 %. Chemotaxonomy indicated UQ-10 as the major quinone; phosphatidylethanolamine, phosphatidylglycerol, and diphosphatidylglycerol as major polar lipids; C 16:0 , C 17:0 , 2-OH C 10:0 , 3-OH C 16:0 , and unresolved C 18:1 ɷ7C/ɷ9C as predominant fatty acids. The cells were found to reduce O 2 , As 5+ , NO 3 - , SO 4 2- and Fe 3+ as alternate electron acceptors. The strain's ability to metabolize dodecane or other alkanes as sole carbon source using As 5+ as terminal electron acceptor was supported by the presence of genes encoding benzyl succinate synthase (bssA like) and molybdopterin-binding site (mopB) of As 5+ respiratory reductase (arrA). Differential phenotypic, chemotaxonomic, genotypic as well as physiological properties revealed that the strain KAs 5-22 T is separated from its nearest recognized Rhizobium species. On the basis of the data presented, strain KAs 5-22 T is considered to represent a novel species of the genus Rhizobium, for which the name Rhizobium arsenicireducens sp. nov. is proposed as type strain (=LMG 28795 T =MTCC 12115 T ).

Effects of process variables in decarburization annealing of Fe-3%Si-0.3%C steel sheet on textures and magnetic properties

NASA Astrophysics Data System (ADS)

Park, Se Min; Koo, Yang Mo; Shim, Byoung Yul; Lee, Dong Nyung

2017-01-01

In Fe-3%Si-0.3%C steel sheet, a relatively strong <100>//ND texture can evolve in the surface layer through the α→γ→α phase transformation in relatively low vacuum (4 Pa) for an annealing time of 10 min and at a cooling rate of 20 K/s. Oxidation of the steel sheet surface prevents the evolution of the <100>//ND texture. However, vacuum-annealing under a vacuum pressure of 1.3×10-3 Pa causes decarburization of the steel sheet, which suppresses oxidation of the steel sheet surface, and subsequent annealing in wet hydrogen of 363 K in dew points causes a columnar grain structure with the <100>//ND texture. After the two-step-annealing (the vacuum annealing under a vacuum pressure of 1.3×10-3 Pa and subsequent decarburizing annealing in wet hydrogen of 363 K in dew points), the decarburized steel sheet exhibits good soft magnetic properties in NO with 3%Si, W15/50 (core loss at 1.5T and 50 Hz) = 2.47 W/kg and B50 (magnetic flux density at 5000 A/m) = 1.71 T.

Amylose Phase Composition As Analyzed By FTIR In A Temperature Ramp: Influence Of Short Range Order On The Thermodynamic Properties

NASA Astrophysics Data System (ADS)

Bernazzani, Paul; Delmas, Genevieve

1998-03-01

Amylose, a major component of starch, is one of the most important biopolymers, being mainly associated with the pharmacological and food industries. Although widely studied, a complete control and understanding of the physical properties of amylose is still lacking. It is well known that structure and phase transition are important aspects of the functionality of biopolymers since they influence physical attributes such as appearance, digestibility, water holding capacity, etc. In the past, we have studied polyethylene phase composition by DSC in a very slow temperature (T) ramp (1K/h) and have demonstrated the presence and importance of short-range order on the polymer and its characteristics. In this study, we evaluated the phase composition of potato amylose and associated the thermodynamic properties with the presence of short-range order. Two methods were correlated, DSC (in a 1K/h T-ramp) and FTIR as a function of temperature, also in a 1K/h T-ramp. The effects of the various phases on thermodynamic properties such as gelation and enzyme or chemical resistance are discussed.

Outcomes and Prognostic Variables in Adenoid Cystic Carcinoma of the Head and Neck: A Recent Experience

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gomez, Daniel R.; Hoppe, Bradford S.; Wolden, Suzanne L.

2008-04-01

Purpose: To analyze the recent experience of patients with adenoid cystic carcinoma treated with radiation therapy at Memorial Sloan-Kettering Cancer Center. Methods and Materials: From 1990 to 2004, a total of 59 patients with a diagnosis of primary adenoid cystic carcinoma of the head and neck received radiation therapy at our institution. The subsite distribution was oral cavity, 28% (n = 17); paranasal sinuses, 22% (n = 13); parotid, 14% (n = 8); submandibular, 14% (n = 8); oropharynx, 10% (n = 6); sublingual, 3% (n = 2); nasopharynx, 3% (n = 2); and other, 5% (n = 3). Tmore » Stage distribution was T1, 34% (n = 20); T2, 19% (n = 11); T3, 14% (n = 8); and T4, 34% (n = 20). Twenty-nine percent of patients (n = 17) were treated with intensity-modulated radiation therapy; 25% (n =15), with three-dimensional conformal therapy, and the remainder, with conventional techniques. Ninety percent (n = 53) of patients received treatment including the base of skull. Results: Median follow-up for surviving patients was 5.9 years. Five-year and 10-year rates of local control and distant metastases-free survival were 91%/81% and 81%/49%, respectively. Five-year and 10-year rates of disease-free and overall survival were 76%/40% and 87%/65%, respectively. On univariate analysis, stage T4 (p = 0.004) and gross/clinical nerve involvement (p = 0.002) were associated with decreased progression free survival, whereas stage T4 and lymph node involvement were associated with decreased overall survival (p = 0.046 and p < 0.001, respectively). Conclusions: Radiation therapy in combination with surgery produces excellent rates of local control, although distant metastases account for a high proportion of failures. Routine treatment to the base of skull reduces the significance of histologic perineural invasion, but major nerve involvement remains an adverse prognostic factor.« less

Prevalence of Trichomonas vaginalis and Coinfection with Chlamydia trachomatis and Neisseria gonorrhoeae in the United States as Determined by the Aptima Trichomonas vaginalis Nucleic Acid Amplification Assay

PubMed Central

Chapin, K.; Smith, J. S.; Aslanzadeh, J.; Snook, J.; Hill, C. S.; Gaydos, C. A.

2012-01-01

Our aim was to determine Trichomonas vaginalis prevalence using the Aptima Trichomonas vaginalis assay (ATV; Gen-Probe) and the prevalence of Chlamydia trachomatis and Neisseria gonorrhoeae coinfections in U.S. women undergoing screening for C. trachomatis/N. gonorrhoeae. Discarded urogenital samples from 7,593 women (18 to 89 years old) undergoing C. trachomatis/N. gonorrhoeae screening using the Aptima Combo 2 assay (Gen-Probe) in various clinical settings were tested with ATV. Overall, T. vaginalis, C. trachomatis, and N. gonorrhoeae prevalences were 8.7%, 6.7%, and 1.7%, respectively. T. vaginalis was more prevalent than C. trachomatis or N. gonorrhoeae in all age groups except the 18- to 19-year-old group. The highest T. vaginalis prevalence was in women ≥40 years old (>11%), while the highest C. trachomatis prevalence (9.2%) and N. gonorrhoeae prevalence (2.2%) were in women <30 years old. Coinfection prevalences were 1.3% for C. trachomatis/T. vaginalis, 0.61% for C. trachomatis/N. gonorrhoeae and N. gonorrhoeae/T. vaginalis, and 0.24% for C. trachomatis/N. gonorrhoeae/T. vaginalis and highest in women <30 years old. T. vaginalis prevalence differed by race/ethnicity, with the highest prevalence in black women (20.2%). T. vaginalis prevalence ranged from 5.4% in family planning clinics to 22.3% in jails. Multivariate analysis determined that ages of ≥40 years, black race, and patient locations were significantly associated with T. vaginalis infection. T. vaginalis is the most common sexually transmitted infection (STI) in women of >40 years, while C. trachomatis and N. gonorrhoeae prevalence is lowest in that age group. Higher T. vaginalis prevalence in women of >40 years is probably attributed to the reason for testing, i.e., symptomatic status versus routine screening in younger women. Coinfections were relatively low. High T. vaginalis prevalence in all age groups suggests that women screened for C. trachomatis/N. gonorrhoeae, whether asymptomatic or symptomatic, should be screened for T. vaginalis. PMID:22622447

49 CFR 178.338-1 - General requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... contacted with a continuously heated glowing platinum wire. The cargo tank must be marked in accordance with... Gauge Inches Stainless steel 18 0.0428 22 0.0269 Low carbon mild steel 12 0.0946 14 0.0677 Aluminum 0...

Comparison of friction force between corroded and noncorroded titanium nitride plating of metal brackets.

PubMed

Kao, Chia-Tze; Guo, Jia-Uei; Huang, Tsui-Hsien

2011-05-01

Titanium nitride (TiN) plating is a method to prevent metal corrosion and can increase the surface smoothness. The purpose of this study was to evaluate the friction forces between the orthodontic bracket, with or without TiN plating, and stainless steel wire after it was corroded in fluoride-containing solution. In total, 540 metal brackets were divided into a control group and a TiN-coated experimental group. The electrochemical corrosion was performed in artificial saliva with 1.23% acidulated phosphate fluoride (APF) as the electrolytes. Static and kinetic friction were measured by an EZ-test machine (Shimadazu, Tokyo, Japan) with a crosshead speed of 10 mm per minute over a 5-mm stretch of stainless steel archwire. The data were analyzed by using unpaired t test and analysis of variance (ANOVA). Both the control and TiN-coated groups' corrosion potential was higher with 1.23% APF solution than with artificial solution (P <0.05). In brackets without corrosion, both the static and kinetic friction force between the control and TiN-coated brackets groups showed a statistically significant difference (P <0.05). In brackets with corrosion, the control group showed no statistical difference on kinetic or static friction. The TiN-coated brackets showed a statistical difference (P <0.05) on kinetic and static friction in different solutions. TiN-coated metal brackets, with corrosion or without corrosion, cannot reduce the frictional force. Copyright © 2011 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Rapid Thermal Processing to Enhance Steel Toughness.

PubMed

Judge, V K; Speer, J G; Clarke, K D; Findley, K O; Clarke, A J

2018-01-11

Quenching and Tempering (Q&T) has been utilized for decades to alter steel mechanical properties, particularly strength and toughness. While tempering typically increases toughness, a well-established phenomenon called tempered martensite embrittlement (TME) is known to occur during conventional Q&T. Here we show that short-time, rapid tempering can overcome TME to produce unprecedented property combinations that cannot be attained by conventional Q&T. Toughness is enhanced over 43% at a strength level of 1.7 GPa and strength is improved over 0.5 GPa at an impact toughness of 30 J. We also show that hardness and the tempering parameter (TP), developed by Holloman and Jaffe in 1945 and ubiquitous within the field, is insufficient for characterizing measured strengths, toughnesses, and microstructural conditions after rapid processing. Rapid tempering by energy-saving manufacturing processes like induction heating creates the opportunity for new Q&T steels for energy, defense, and transportation applications.

Harmonic surface acoustic waves on gallium nitride thin films.

PubMed

Justice, Joshua; Lee, Kyoungnae; Korakakis, D

2012-08-01

SAW devices operating at the fundamental frequency and the 5th, 7th, 9th, and 11th harmonics have been designed, fabricated, and measured. Devices were fabricated on GaN thin films on sapphire substrates, which were grown via metal organic vapor phase epitaxy (MOVPE). Operating frequencies of 230, 962, 1338, 1720, and 2100 MHz were achieved with devices that had a fundamental wavelength, lambda0 = 20 μm. Gigahertz operation is realized with relatively large interdigital transducers that do not require complicated submicrometer fabrication techniques. SAW devices fabricated on the GaN/sapphire bilayer have an anisotropic propagation when the wavelength is longer than the GaN film thickness. It is shown that for GaN thin films, where kh(GaN) > 10 (k = 2pi/lambda and h(GaN) = GaN film thickness), effects of the substrate on the SAW propagation are eliminated. Bulk mode suppression at harmonic operation is also demonstrated.

Nanoplatinates for Breast Cancer

DTIC Science & Technology

2010-10-01

18 . NUMBER OF...kg Oxaliplatin15 mg/kg NP 5 mg/kg NP 15mg/kg No. of Days Tu m or V ol um e (m m 3 ) Tumor volume 0 1 2 3 4 5 6 7 8 15 16 17 18 19 20 21 22 23 24...O O OHOH HO OH OH OH OH OH HO HO HO H3N Pt H3N OH2 OH2 A B 4hr 6hr 12hr 24hr EDC 0 1 2 3 4 5 6 7 8 12 13 14 15 16 17 18 19 days W ei gh t o f m ic

Modeling Plastic Shocks in Periodic Laminates with Gradient Plasticity Theories

DTIC Science & Technology

2007-08-26

stainless steel (SS)) layers with volume fractions being respectively, LLf /11= , LLf /22= . (3) Material characteristics of the...characteristics of polycarbonate and stainless steel Poisson ratio Elastic shear modulus Mass density PC...Polycarbonate) 0.37 0.94 Gpa 1190 kg/m3 SS ( Stainless steel ) 0.29 77 Gpa 7890 kg

Analysis of Wartime Consumption Rates for Chemical Defensive Equipment. Volume 3. Appendix D. Post-Processor Data

DTIC Science & Technology

1986-05-01

101.18 113.96 123.0 -N-----5 CTIC CATA - 10 RMXL FO]R WVCl&A KR DAYS 1 DRDI 15 Mv% tM OF O-eiICA&L RT•M••M 25 MIL DAS FJIF FOER EKH ODY OF BATTLE OaNm 1...0.68 0.68 6.66s 0.08 0.6 AG 0.68 .0.6 0.68 6.68 0.68e 66 0. 68 0. 68 ~e 0.0 AVEVM NM. RMAIE PER DAY PER 160M ~ TM AfW I CaMrWi 1 2 3 4 5 6 7 8 MCG 2...I6 IN W3’PPLM2 FR’ T - TMS CJ1Rw 1 2 3 4 5 6 7 8 TOTAL 1 0.95 3.42 2.14 0.19 3.05 5.02 4.25 0.60 19.1 2 4.37 3.29 5.57 2.22 3.93 0.0 6.60 3.94 23.1 3

Determination of the analgesic components of Spasmomigraine tablet by liquid chromatography with ultraviolet detection.

PubMed

Elbarbry, Fawzy A; Mabrouk, Mokhtar M; El-Dawy, Mohamed A

2007-01-01

A procedure was developed for the determination of the analgesic components of Spasmomigraine tablets, which are ergotamine (I), propyphenazone (II), caffeine (III), camylofin (IV), and mecloxamine (V). They were subjected to high-performance liquid chromatography on a column (300 x 3.9 mm, 10 rlm particle size) packed with micro-Bondapak C18. Separations were achieved with the mobile phase methanol-water-triethylamine (60 + 40 + 0.1, v/v/v) flowing at a rate of 1.5 mL/min, and quantitative determination was performed at 254 nm at ambient temperature for I-III; acetonitrile-25 mM KH2PO4-acetic acid (45 + 55 + 0.2, v/v/v), flowing at a rate of 1.5 mL/min and detection at 234 nm at ambient temperature, was used for IV and V. Methyl paraben was used as an internal standard. The detection limits were 0.35 (I), 5.0 (11), 1.5 (111), 3.0 (IV), and 2.0 microg/mL (V). The method was accurate (mean recovery 98+/-2%, n = 4) and precise (coefficient of variation <5%, n = 5). The proposed method is rapid and sensitive and, therefore, suitable for the routine control of these ingredients in multicomponent dosage forms.

Brunswick NAS, Maine. Revised Uniform Summary of Surface Weather Observations (RUSSWO). Parts A-F.

DTIC Science & Technology

1982-06-02

23.’f .a. .3 2,.- .fl .i rOTAL NUEE Of ONATIONS 913 C (- porn USAPETAC Poe" 04.5 (OLA) avo. n ,,,inm oI tis pow Am iounnln AI. 6 GLOBAL CLIMATOLOGY...N U 29-20 31 D.. Boy lb Wet i61wb POWn.S ,16/-IT9, F ( " - --21--,,10 -22/-23-- 5 -24/-25 2 r OTAL 2*lZD40*O0. T .I .3 h 01 *1 821811 821 _ 821 (j1

Reduced Th22 cell proportion and prevention of atopic dermatitis in infants following maternal probiotic supplementation.

PubMed

Rø, A D B; Simpson, M R; Rø, T B; Storrø, O; Johnsen, R; Videm, V; Øien, T

2017-08-01

In the randomized, controlled study Probiotics in the Prevention of Allergy among Children in Trondheim (ProPACT), maternal probiotic supplementation reduced the incidence of atopic dermatitis (AD) in the offspring. In the current study, we hypothesized that the effect was mediated by a shift in the T helper (Th) cells in the children. To examine whether Th cell proportions were affected by maternal probiotic supplementation and thus could mediate the preventive effect of probiotics on AD. A total of 415 pregnant women were randomized to ingest a combination of Lactobacillus rhamnosus GG (LGG), Bifidobacterium animalis subsp. lactis Bb-12 (Bb-12) and Lactobacillus acidophilus La-5 (La-5) or placebo, and their offspring were assessed for AD during the first 2 years of life. Peripheral blood collected at 3 months of age was analysed for regulatory T cells (n=140) and Th subsets (n=77) including Th1, Th2, Th9, Th17 and Th22. The proportion of Th22 cells was reduced in children in the probiotic group compared to the placebo group (median 0.038% vs 0.064%, P=.009). The difference between the probiotic and placebo groups was also observed in the children who did not develop AD during the 2-year follow-up. The proportion of Th22 cells was increased in children who developed AD compared to the children who did not develop AD (0.090% vs 0.044%, P<.001). Mediation analysis indicated that the preventive effect of probiotics was partially mediated through the reduction in Th22 cells. Perinatal maternal probiotic supplementation with a combination of LGG, Bb-12 and La-5 reduced the proportion of Th22 cells in 3-month-old children. This may partially explain the preventive effect of probiotics on AD. © 2017 John Wiley & Sons Ltd.

Separated and Nonseparated Turbulent Flows about Axisymmetric Nozzle Afterbodies. Part II. Detailed Flow Measurements

DTIC Science & Technology

1979-10-01

total pressures and the model static pressures were converted to a d-c electrical signal by one of two Scanivalve ®, Druck Model PDCR22, 0- to l0...31 3d 33 3+ 3’:, 3~ 3~ ~d ~ 4 4 b 4 h ,.,.9 50 0 , 0 0 + 0 . 0 9 9 n . 0 1 4 0.019 0 , 0 ~ 4 0 . 0 2 9 C . 0 3 ~ ~ . 0 3...1 ° 5 8 5 £ 02 0 .322 - 1 ° 2 5 b £ O~ 0,3~2 - 9 . f i ~ 3 £ t)l 0 ,36~ - 7 , b P ~ £ 01 0 . 3d ~ - 5 , ~ 3 9 £ Ol 0 , ~ 0 ~ - ~ ° 5 1

Improved production and processing of ⁸⁹Zr using a solution target.

PubMed

Pandey, Mukesh K; Bansal, Aditya; Engelbrecht, Hendrik P; Byrne, John F; Packard, Alan B; DeGrado, Timothy R

2016-01-01

The objectives of the present work were to improve the cyclotron production yield of (89)Zr using a solution target, develop a practical synthesis of the hydroxamate resin used to process the target, and develop a biocompatible medium for (89)Zr elution from the hydroxamate resin. A new solution target (BMLT-2) with enhanced heat dissipation capabilities was designed by using helium-cooled dual foils (0.2 mm Al and 25 μ Havar) and an enhanced water-cooled, elongated solution cavity in the target insert. Irradiations were performed with 14 MeV protons on a 2M solution of yttrium nitrate in 1.25 M nitric acid at 40-μA beam current for 2 h in a closed system. Zirconium-89 was separated from Y by use of a hydroxamate resin. A one-pot synthesis of hydroxamate resin was accomplished by activating the carboxylate groups on a carboxymethyl cation exchange resin using methyl chloroformate followed by reaction with hydroxylamine hydrochloride. After trapping of (89)Zr on hydroxamate resin and rinsing the resin with HCl and water to release Y, (89)Zr was eluted with 1.2 M K2HPO4/KH2PO4 buffer (pH3.5). ICP-MS was used to measure metal contaminants in the final (89)Zr solution. The BMLT-2 target produced 349±49 MBq (9.4±1.2 mCi) of (89)Zr at the end of irradiation with a specific activity of 1.18±0.79 GBq/μg. The hydroxamate resin prepared using the new synthesis method showed a trapping efficiency of 93% with a 75 mg resin bed and 96-97% with a 100-120 mg resin bed. The elution efficiency of (89)Zr with 1.2M K2HPO4/KH2PO4 solution was found to be 91.7±3.7%, compared to >95% for 1 M oxalic acid. Elution with phosphate buffer gave very small levels of metal contaminants: Al=0.40-0.86 μg (n=2), Fe=1.22±0.71 μg (n=3), Y=0.29 μg (n=1). The BMLT-2 target allowed doubling of the beam current for production of (89)Zr, resulting in a greater than 2-fold increase in production yield in comparison with a conventional liquid target. The new one-pot synthesis of hydroxamate resin provides a simpler synthesis method for the (89)Zr trapping resin. Finally, phosphate buffer elutes the (89)Zrfrom the hydroxamate resin in high efficiency while at the same time providing a more biocompatible medium for subsequent use of (89)Zr. Copyright © 2015 Elsevier Inc. All rights reserved.

National Dam Safety Program. Alder Pond Dam (Inventory Number N.Y. 1489), Black River Basin, Oneida County, New York. Phase I Inspection Report,

DTIC Science & Technology

1981-06-17

CAMAL )57 7) Maximum K~nown Flood 8) At Time of Inspection______ 93-15-4( 9/8C) AL R Po4 PAPA CREST: (CLAT IE) ELEVATION: .7 Type: -AQI H 5 a Width...T - L jR iT BLACK RNE. CAmAL --- Io 1500 A .T- PRO F ILE. T-OP EABA"MEIPT (CANAL) --ECT -14 A-A to/8O 100 I-.U 2O 11 0. 7 22I- co I.)-- LII___ ___ __1

Precipitation Behaviors of TiN Inclusion in GCr15 Bearing Steel Billet

NASA Astrophysics Data System (ADS)

Tian, Qianren; Wang, Guocheng; Zhao, Yang; Li, Jing; Wang, Qi

2018-06-01

There are many types of non-metallic TiN-based inclusions observed in GCr15 bearing steel, including single-particle TiN, multi-particle polymerized TiN, and complex inclusions like TiN-MnS, TiN-MgO-MgAl2O4 (TiN-MgO-MA), and TiN-MgAl2O4-MnS (TiN-MA-MnS). Thermodynamic calculations suggest that single-particle TiN precipitates dominate the mushy zone of GCr15 bearing steel. Kinetic calculations regarding TiN growth suggest that the final size of the single-particle TiN ranges between 1 and 6 μm in the initial concentration range of [pct Ti] = 0.0060 to 0.0079 and [pct N] = 0.0049 to 0.0070, at 1620 to 1640 K and a local cooling rate of 0.5 to 10 K/s. The multi-particle polymerized TiN are formed by single TiN particles in three stages: single-particle TiN inclusions approach each other drawn by the cavity bridge force (CBF), local active angles consolidate, and neck region sintering occurs. Based on the thermodynamic calculations of TiN, MnS, and MgO precipitation, the formation behaviors of complex inclusions of TiN-MnS, TiN-MgO-MA, and TiN-MA-MnS were investigated.

Aqueous aerosol may build up large upper tropospheric ice supersaturation

NASA Astrophysics Data System (ADS)

Bogdan, Anatoli; Molina, Mario J.

2010-05-01

Keywords: ice supersaturation, upper tropospheric cirrus clouds, freezing of aqueous aerosol. Observations often reveal enhanced and persistent upper tropospheric (UT) ice supersaturation, Si up to 100%, independently of whether cirrus ice clouds are present or not (Krämer et al., 2009; Lawson et al., 2008). However, a water activity criterion (WAC) (Koop et al., 2000) does not allow the formation of Si > ~67% by the homogeneous freezing of aqueous droplets even at the lowest atmospheric temperature of ~185 K. For aqueous aerosol the WAC predicts the existence of a so called homogeneous ice nucleation threshold which, being expressed as Si, is between ~52 and 67% in the temperature range of ~220 - 185 K. The nature of the formation of large Si remains unclear. Since water vapor is the dominant greenhouse gas it is important to know the nature of the accumulation and persistence of water vapor in the UT. We studied the freezing behavior of micrometer-scaled 3-, 4-, and 5-component droplets, which contain different weight fractions of H2O, H2SO4, HNO3, (NH4)2SO4, (NH4)HSO4, NH4NO3, and (NH4)3H(SO4)2. The study was performed between 133 and 278 K at cooling rates of 3, 0.1, and 0.05 K/min using differential scanning calorimetry (DSC) (Bogdan and Molina, 2010). The cooling rates of 0.1 and 0.05 K/min (6 and 3 K/h) are similar to the smallest reported synoptic temperature change of ~2 K/h (Carslaw et al., 1998). Using the measured freezing temperature of ice, Ti, and the thermodynamic E-AIM model of the system of H+ - NH4+ - SO42-- NO3-- H2O (Clegg et al., 1998), we calculated the corresponding clear-sky Si which would be built up immediately prior to the formation of ice cirrus clouds by the homogeneous freezing of aqueous aerosol of similar composition. We found that our calculated values of Si are both larger and smaller than the homogeneous ice nucleation threshold. For example, for the droplets of compositions of 15/10 and 20/10 wt % (NH4)3H(SO4)2/H2SO4, which freeze at 194 and 186 K, respectively, the calculated clear-sky Si can exceed 80%. Although our Si values are smaller than the largest observed value of Si ≈ 100%, they are nevertheless larger than the Si ≈ 67% predicted by the WAC at 185 K. Our results can give an impetus for the study of whether multi-component aqueous aerosol, which besides inorganic components also contains organics, may produce the observed Si ≈ 100%. Krämer, M., Schiller, C., Afchine, A., Bauer, R., Gensch, I., Mangold, A.., Schlicht, S., Spelten, N., Sitnikov, N., Borrmann, S., de Reus, M., Spichtinger, P. (2009), Atmos. Chem. Phys. 9, 3505. Lawson, R. P., Pilson, B., Baker, B., Mo, Q., Jensen, E., Pfister, L., Bui, P. (2008), Atmos. Chem. Phys. 8, 1609. Koop, T., Luo, B., Tsias, A., Peter, T. (2000), Nature, 406, 611. Bogdan, A. and Moilna, M. J. (2010), J. Phys. Chem. A (Published online: 5 February). Carslaw, K. S., Wirth, M., Tsias, A., Luo, B. P., Dörnbrack, A., Leutbecher, M., Volkert, H., Renger, W., Bacmeister, J. T., Peter, T. (1998), J. Geophys. Res. 103, 5785. Clegg, S. L., Brimblecombe, P., Wexler, A. S. (1998), J. Phys. Chem. A 102, 2137.

Investigation of γ-(2,3-Epoxypropoxy)propyltrimethoxy Silane Surface Modified Layered Double Hydroxides Improving UV Ageing Resistance of Asphalt.

PubMed

Zhang, Canlin; Yu, Jianying; Xue, Lihui; Sun, Yubin

2017-01-19

γ-(2,3-Epoxypropoxy)propyltrimethoxy silane surface modified layered double hydroxides (KH560-LDHs) were prepared and used to improve the ultraviolet ageing resistance of asphalt. The results of X-ray photoelectron spectrometry (XPS) indicated that KH560 has been successfully grafted onto the surface of LDHs. The agglomeration of LDHs particles notably reduced after KH560 surface modification according to scanning electron microscopy (SEM), which implied that the KH560 surface modification was helpful to promote the dispersibility of LDHs in asphalt. Then, the influence of KH560-LDHs and LDHs on the physical and rheological properties of asphalt before and after UV ageing was thoroughly investigated. The storage stability test showed that the difference in softening point (Δ S ) of LDHs modified asphalt decreased from 0.6 °C to 0.2 °C at an LDHs content of 1% after KH560 surface modification, and the tendency became more pronounced with the increase of LDH content, indicating that KH560 surface modification could improve the stability of LDHs in asphalt. After UV ageing, the viscous modulus ( G'' ) of asphalt significantly reduced, and correspondingly, the elastic modulus ( G' ) and rutting factor ( G */sin δ) rapidly increased. Moreover, the asphaltene increased and the amount of "bee-like" structures of the asphalt decreased. Compared with LDHs, KH560-LDHs obviously restrained performance deterioration of the asphalt, and helped to relieve the variation of the chemical compositions and morphology of asphalt, which suggested that the improvement of KH560-LDHs on UV ageing resistance of asphalt was superior to LDHs.

Lower Wingate Test Power Outcomes From "All-Out" Pretest Pedaling Cadence Compared With Moderate Cadence.

PubMed

Lunn, William R; Zenoni, Maria A; Crandall, Ian H; Dress, Ashley E; Berglund, Michelle L

2015-08-01

The aim of the present study was to determine the effect of different pretest pedaling cadences on power outcomes obtained during the Wingate Anaerobic Test (WAnT). Vigorously exercising adult men (n = 14, 24.9 ± 1.2 years) and women (n = 14, 20.4 ± 0.6 years) participated in a randomized crossover study during which they performed the 30-second WAnT on a mechanically braked cycle ergometer (0.075 kg·kg(-1) body weight) under 2 conditions. Participants pedaled maximally with an unloaded flywheel during 5 seconds before resistance was applied and the test began (FAST). In another trial, participants maintained a moderate cadence (80 revolutions per minute [rpm]) during 5 seconds before the test began (MOD). All other components of the WAnT were identical. Peak power (PP), mean power (MP), minimum power (MinP), fatigue index (%FAT), and maximum cadence during test were recorded. Comparisons were made using a 2 × 2 factorial repeated-measures analysis of variance. Regardless of gender, the FAST condition resulted in 22.2% lower PP (612.6 ± 33.0 W vs. 788.3 ± 43.5 W), 13.3% lower MP (448.4 ± 22.2 W vs. 517.2 ± 26.4 W), 11.7% lower MinP (280.9 ± 14.8 W vs. 318.3 ± 17.2 W), and 9.0% lower %FAT (53.5 ± 1.3% vs. 58.8 ± 1.5%) than MOD condition (p < 0.01; mean ± SD). Similar outcomes were observed within gender. The authors conclude that practitioners of the WAnT should instruct participants to maintain a moderate pedal cadence (∼80 rpm) during 5 seconds before the test commences to avoid bias from software sampling and peripheral fatigue. Standardizing the pretest pedal cadence will be important to exercise testing professionals who compare data with norms or generate norms for specific populations.

Investigating The Kinematics of Canids and Felids

NASA Astrophysics Data System (ADS)

Sur, D.

2016-12-01

For all organisms, metabolic energy is critical for survival. While moving efficiently is a necessity for large carnivores, the influence of kinematics on energy demand remains poorly understood. We measured the kinematics of dogs, wolves, and pumas to detect any differences in their respective energy expenditures. Using 22 kinematic parameters measured on 78 videos, we used one-way ANOVAs and paired T-tests to compare 5 experimental treatments among gaits in dogs (n=11 in 3 breed groups), wolves (n=2), and pumas (n=2). Across the measured parameters, we found greater kinematic similarity than expected among dog breeds and no trend in any of the 22 parameters regarding the effect of steepness on locomotion mechanics. Similarly, treadmill kinematics were nearly identical to those measured during outdoor movement. However, in 3 inches of snow, we observed significant differences (p<0.05) in 5 of the 22 parameters for one wolf. When comparing canids (wolves and dogs) to a felid (pumas), we found that pumas and dogs are the most kinematically distinct (differing in 13 of 22 parameters, compared with 5 of 22 for wolves and pumas). Lastly, compared with wolves, walking pumas had larger head angles (p=0.0025), forelimb excursion angles (p=0.0045), and hindlimb excursion angles (p=0.0327). After comparing the energetics of pumas and dogs with their respective kinematics, we noted that less dynamic kinematics result in energy savings. Through tracking the locations and gait behavior of large carnivores, novel sensor technology can reveal how indoor kinematics applies to wild animals and improve the conservation of these species.

Taxonomic Evaluation of Cleveland Harbor Lake Areas

DTIC Science & Technology

2014-01-01

collected using a standard (8.2-L) stainless steel ponar grab (229 x 229 mm) in basic accordance with USEPA (2001). The grab sampler was dropped from...through stacked 1.0- and 0.5-mm stainless steel sieves to separate coarse and fine material. Sample material retained in both sieves was thoroughly... 416 . Berry, E. 1943. The Amnicolidae of Michigan: Distribution, ecology, and taxonomy. Misc. Publ. Mus. Zool. U. Mich. 57:1-68. Dillon, R. T., Jr

[The impact of experience in bearing child on the body mass index and obesity in women].

PubMed

Lai, Jian-qiang; Yin, Shi-an

2009-02-01

To analyze the relations of body mass index(BMI)and obese prevalence in differently aged women and explore the effective strategy for preventing obesity among adult Chinese women. This study was based on the data from 2002 National Nutrition and Health Survey. The method of multi-steps cluster sampling was adopted. Total subjects including unmarried women (n = 2474), married women without the experience of childbearing (n = 10,816), and married and bearing-child women (n = 4103), were 17,393. In urban areas, the average body weights of unmarried, married and without childbearing experience, and the married with born-child were (53.7 +/- 9.0) kg, (57.6 +/- 9.4) kg and (54.5 +/- 8.5) kg respectively; the body weights of unmarried, married and without childbearing experience were significantly higher than that of the married with born-child women (t = 12.25, P < 0.001; t = 8.32, P < 0.001); the BMIs of unmarried, married without childbearing experience, and the married with born-child women were (21.1 +/- 3.3) kg/m(2), (22.8 +/- 3.4) kg/m(2) and (22.0 +/- 2.9) kg/m(2) respectively; the BMIs of married without childbearing experience and married with born-child women were significantly higher than that of unmarried women (t = 14.88, P < 0.001; t = 5.76, P < 0.001). In the rural areas, the body weights of unmarried, married without childbearing experience, and the married with born-child women were (52.3 +/- 7.8) kg, (55.3 +/- 8.6) kg and (52.8 +/- 8.1) kg respectively; the body weights of unmarried, the married with born-child women were significantly higher than that of married without childbearing experience (t = 11.67, P < 0.001; t = 14.15, P < 0.001); the BMIs of unmarried, married without childbearing experience, and the married with born-child women were (21.2 +/- 2.8) kg/m(2), (22.5 +/- 3.1) kg/m(2), and (21.8 +/- 3.0) kg/m(2) respectively; the BMIs of married and the married with born-child were significantly higher than that of unmarried women (t = 13.80, P < 0.001; t = 5.34, P < 0.001). In urban areas, the rate of low body weight of unmarried women (18.1%) was higher than that of married without childbearing experience and married with born-child group (7.3% vs. 9.1%; comparing with married without childbearing experience: chi(2) = 113.69, P < 0.001; comparing with married with born-child: chi(2) = 29.65, P < 0.001); the prevalence of overweight and obesity (32.7%) in married without childbearing was significantly higher than that of unmarried women (14.4%) (chi(2) = 28.257, P < 0.001). In rural areas, the rate of low body weight of unmarried women (12.4%) was higher than that of married without childbearing group (6.7%, chi(2) = 50.040, P < 0.001); however, the prevalence of overweight (22.4%) in the married without childbearing was significantly higher than that of unmarried women (12.3%) (chi(2) = 69.119, P < 0.001) and the married with born-child women (15.4%) (chi(2) = 69.866, P < 0.001). The prevalence of overweight and obesity of the married with born-child women was decreasing with extending time of postpartum in urban and rural areas. Weight retention of married with born-child women was one of the most important factors leading to the obesity in the adulthood. However, more attentions should be paid to the changing trend of body weight in the married without childbearing experience.

An Oceanographic and Climatological Atlas of the Chukchi Sea

DTIC Science & Technology

1990-02-01

61 Vi I 3 I I I I U BLANK ] I I I I I I I I I I I viii I INTRODUCTION In the event of an oil spill in the Chukchi for decision making in...Point Ley Borrow 256 2- 25- 1 � 3254 ! 7879 020- 020. 020. aL Q 0 0U’- 0 0 0 0 0 0 Marine Area A Marino Area 8 Marine Area 0 1 ~ 56 0 0204 2.0 0 𔃺...T CAL MILES VI SI iTy N NAUrICAL ki..E<. N NE E SE S S* tv NA ZN- NE E SE S 3w Or I C N~ E SE S Stv a N* 42 2 22 � ? 0 2 5 2 MY$ U.Ien ]fTin City

A Locally Nonlinear Interpretation of PUV Measurements

DTIC Science & Technology

1998-10-01

k ,h s vyk U ygk tanh khs0Ž . Ž .1 a a a cosh k hqzŽ .P obsf v ,k ,h sr g hyp s0Ž .2 a dcosh kh 14Ž .k cosh k hqzŽ .1 UV obsf v ,k ,h sU q vyk U hyu ...s0Ž . Ž .3 a 1 a a 1k sinh kh k cosh k hqzŽ .2 UV obsf v ,k ,h sU q vyk U hyu s0,Ž . Ž .4 a 2 a a 2k sinh kh In principle, a unique local solution at

49 CFR 178.338-1 - General requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... glowing platinum wire. The cargo tank must be marked in accordance with § 178.338-18(b)(7). (3) Each... steel 18 0.0428 22 0.0269 Low carbon mild steel 12 0.0946 14 0.0677 Aluminum 0.125 0.1000 (f) An...

Association between Erythrocyte Membrane Phospholipid Fatty Acids and Sleep Disturbance in Chinese Children and Adolescents

PubMed Central

Tang, Jun; Yan, Yinkun; Zheng, Ju-Sheng; Mi, Jie

2018-01-01

The relationship between circulating fatty acid (FA) composition and childhood sleep disturbance remains largely unclear. We aimed to investigate the association of erythrocyte membrane FA composition with prevalence of sleep disturbance in Chinese children and adolescents. A cross-sectional survey was conducted among 2337 school-aged children and adolescents who completed a clinical assessment in Beijing, China. Presence of sleep disturbance was self-reported or parent-reported by questionnaires. Erythrocyte FAs were measured by gas chromatography, and desaturase activities were estimated by FA ratios. Multivariable-adjusted odds ratios (ORs) and 95% confidence intervals (CIs) for sleep disturbance across FA quartiles were calculated by a logistical regression model. We found higher proportions of erythrocyte phospholipid 24:0, 24:1n-9, and lower proportions of total n-3 polyunsaturated FA (PUFA), 22:5n-3 and 22:6n-3 in participants with sleep disturbance compared with those without. In the logistical regression models, significant inverse associations were found for total n-3 PUFA, 22:5n-3 and 22:6n-3, the highest versus lowest quartile ORs and 95% CIs were 0.57 (0.40, 0.82), 0.67 (0.47, 0.97) and 0.69 (0.49, 0.96), respectively. For per 1 SD difference of proportion, OR and 95% CI of prevalence of sleep disturbance was 0.91 (0.86, 0.97) for total n-3 PUFA, 0.90 (0.82, 0.98) for 22:5n-3, and 0.92 (0.86, 0.99) for 22:6n-3, respectively. No significant association was found for saturated fatty acids, monounsaturated fatty acids, n-6 polyunsaturated fatty acids or FA ratios. The present study suggested that erythrocyte n-3 PUFAs, especially 22:5n-3 and 22:6n-3, are inversely associated with prevalence of sleep disturbance in Chinese children and adolescents. PMID:29534525

Impact of Si on Microstructure and Mechanical Properties of 22MnB5 Hot Stamping Steel Treated by Quenching & Partitioning (Q&P)

NASA Astrophysics Data System (ADS)

Linke, Bernd M.; Gerber, Thomas; Hatscher, Ansgar; Salvatori, Ilaria; Aranguren, Iñigo; Arribas, Maribel

2018-01-01

Based on 22MnB5 hot stamping steel, three model alloys containing 0.5, 0.8, and 1.5 wt pct Si were produced, heat treated by quenching and partitioning (Q&P), and characterized. Aided by DICTRA calculations, the thermal Q&P cycles were designed to fit into industrial hot stamping by keeping partitioning times ≤ 30 seconds. As expected, Si increased the amount of retained austenite (RA) stabilized after final cooling. However, for the intermediate Si alloy the heat treatment exerted a particularly pronounced influence with an RA content three times as high for the one-step process compared to the two-step process. It appeared that 0.8 wt pct Si sufficed to suppress direct cementite formation from within martensite laths but did not sufficiently stabilize carbon-soaked RA at higher temperatures. Tensile and bending tests showed strongly diverging effects of austenite on ductility. Total elongation improved consistently with increasing RA content independently from its carbon content. In contrast, the bending angle was not impacted by high-carbon RA but deteriorated almost linearly with the amount of low-carbon RA.

P/M Processing of Rare Earth Modified High Strength Steels.

DTIC Science & Technology

1980-12-01

AA094 165 TRW INC CLEVELAND OH MATERIALS TECHNOLOGY F 6 P/N PROCESSING OF RARE EARTH MODIFIED HIGH STRENGTH STEELS DEC So A A SHEXM(ER NOOŕT76-C...LEVEL’ (7 PIM PROCESSING OF RARE EARTH MODIFIED HIGH STRENGTH STEELS By A. A. SHEINKER 00 TECHNICAL REPORT Prepared for Office of Naval Research...Processing of Rare Earth Modified High 1 Technical -’ 3t eC"Strength Steels * 1dc4,093Se~ 9PEFRIGOGNZTONAEADADDRESS 10. PROGRAM ELEMENT. PROJECT. TASK

Investigation and Application of Nb Microalloying Technology in Seamless Steel Tube with High Performance

NASA Astrophysics Data System (ADS)

Zhang, Chuanyou; Wang, Qian; Sun, Yu; Wang, Huibin; Zhang, Wei; Wang, Qingfeng; Guo, Aimin; Sun, Kaiming

Extensive investigations of metallurgical roles played by Nb microalloying in advanced products of seamless steel tube have been carried out. The results show that with Nb microalloyed , the recrystallized austenite grain (RAG) and final ferrite grain of tubular steel are evidently refined even experiencing a piercing and a continuous rolling at very high temperature, and a certain quantity of (Nb,V)(C,N) and (Ti,Nb,V)(C,N) particles form on air cooling. Moreover, for quenching (Q) & tempering (T) treated tubular steels, the nanoscale particles of (Nb,V) (C,N) further precipitate on heating stage of Q at 900-1000°C, leading to a significant refinement of prior austenite grain (PAG) and final martensitic or bainitic packet/block structures, and during subsequent T at 600-700°C, producing an improved resistance to softening.

The protective effect of thalidomide on left ventricular function in a rat model of diabetic cardiomyopathy.

PubMed

Kim, Dae-Hee; Kim, Yong-Jin; Chang, Sung-A; Lee, Hye-Won; Kim, Ha-Na; Kim, Hyung-Kwan; Chang, Hyuk-Jae; Sohn, Dae-Won; Park, Young-Bae

2010-10-01

To evaluate the protective effect of thalidomide, a potent anti-inflammatory drug, on the development of diabetic cardiomyopathy (DMCMP). We induced type 1 diabetes using streptozocin in 8-week-old Sprague-Dawley rats, divided them into two groups-a thalidomide treatment group (DM-T, n = 15) and a non-treatment group (DM-N, n = 15)-and compared them with a normal control (n = 10). Ten weeks after diabetes induction, heart and lung mass indices were higher in the DM-N group compared with the control group. In the DM-T group, increases in heart and lung mass indices were attenuated compared with the DM-N group. On echocardiographic examination, systolic and diastolic mitral annulus velocities were impaired in the DM-N group, but they remained normal in the DM-T group. On haemodynamic analyses, left ventricular (LV) systolic function, represented by end-systolic elastance (0.35 ± 0.14 vs. 0.18 ± 0.07 mmHg/μl, P < 0.001) and preload-recruitable stroke work (90.5 ± 24.3 vs. 51.8 ± 22.0 mmHg, P < 0.001), was preserved in the DM-T group compared with the DM-N group. Likewise, deterioration of LV diastolic function was attenuated in the DM-T group. Increases in serum levels of TNF-α were attenuated in the DM-T group compared with the DM-N group. On histological analysis, thalidomide treatment lowered total myocardial collagen content and the expression of TNF-α, IL-1β, ICAM-1, and VCAM-1. In an animal model of DMCMP, deterioration of LV systolic and diastolic function was partially prevented by thalidomide treatment.

Quantitative assessment of biliary stent artifacts on MR images: Potential implications for target delineation in radiotherapy.

PubMed

Gurney-Champion, Oliver J; Bruins Slot, Thijs; Lens, Eelco; van der Horst, Astrid; Klaassen, Remy; van Laarhoven, Hanneke W M; van Tienhoven, Geertjan; van Hooft, Jeanin E; Nederveen, Aart J; Bel, Arjan

2016-10-01

Biliary stents may cause susceptibility artifacts, gradient-induced artifacts, and radio frequency (RF) induced artifacts on magnetic resonance images, which can hinder accurate target volume delineation in radiotherapy. In this study, the authors investigated and quantified the magnitude of these artifacts for stents of different materials. Eight biliary stents made of nitinol, platinum-cored nitinol, stainless steel, or polyethylene from seven vendors, with different lengths (57-98 mm) and diameters (3.0-11.7 mm), were placed in a phantom. To quantify the susceptibility artifacts sequence-independently, ΔB0-maps and T2 ∗ -maps were acquired at 1.5 and 3 T. To study the effect of the gradient-induced artifacts at 3 T, signal decay in images obtained with maximum readout gradient-induced artifacts was compared to signal decay in reference scans. To quantify the RF induced artifacts at 3 T, B1-maps were acquired. Finally, ΔB0-maps and T2 ∗ -maps were acquired at 3 T of two pancreatic cancer patients who had received platinum-cored nitinol biliary stents. Outside the stent, susceptibility artifacts dominated the other artifacts. The stainless steel stent produced the largest susceptibility artifacts. The other stents caused decreased T2 ∗ up to 5.1 mm (1.5 T) and 8.5 mm (3 T) from the edge of the stent. For sequences with a higher bandwidth per voxel (1.5 T: BW vox > 275 Hz/voxel; 3 T: BW vox > 500 Hz/voxel), the B0-related susceptibility artifacts were negligible (<0.2 voxels). The polyethylene stent showed no artifacts. In vivo, the changes in B0 and T2 ∗ induced by the stent were larger than typical variations in B0 and T2 ∗ induced by anatomy when the stent was at an angle of 30° with the main magnetic field. Susceptibility artifacts were dominating over the other artifacts. The magnitudes of the susceptibility artifacts were determined sequence-independently. This method allows to include additional safety margins that ensure target irradiation.

Economic Drivers of Strategic & Critical Materials

DTIC Science & Technology

2012-05-01

Calla<la. r>eru, cnre ZINC 7J ----i Can.ad:J, Peru, Mexico, l relaniJ TIT .. .Nll.JM (&p1111ge) ’i">9 -----j K azaUI&tan. Japan. ~ R~a ~.0:!\\JM Ml N...G YPS’Uloil PHOSPI1AT E ROCK IRON and STEEL IRON and STE EL SlAG OEME:NT PUMICE DIIL\\IO.N !> (na:lr.ll t1du&trtal s!Oile) U:ME STO.N E (Ct...PLATINUM ZINC TU.NGSTE.N mA.~w.l ($f10nge) HICK EL PEAT MAGNESIUM METAL SltVER S t’UCON BERYLUUM MAGNESIUM COMPOU l>S ALUMI NUM PUMICIE

Relative Modification of Prompt ψ(2S) and J/ψ Yields from pp to PbPb Collisions at sqrt[s_{NN}]=5.02  TeV.

PubMed

Sirunyan, A M; Tumasyan, A; Adam, W; Asilar, E; Bergauer, T; Brandstetter, J; Brondolin, E; Dragicevic, M; Erö, J; Flechl, M; Friedl, M; Frühwirth, R; Ghete, V M; Hartl, C; Hörmann, N; Hrubec, J; Jeitler, M; König, A; Krätschmer, I; Liko, D; Matsushita, T; Mikulec, I; Rabady, D; Rad, N; Rahbaran, B; Rohringer, H; Schieck, J; Strauss, J; Waltenberger, W; Wulz, C-E; Chekhovsky, V; Dvornikov, O; Dydyshka, Y; Emeliantchik, I; Litomin, A; Makarenko, V; Mossolov, V; Stefanovitch, R; Suarez Gonzalez, J; Zykunov, V; Shumeiko, N; Alderweireldt, S; De Wolf, E A; Janssen, X; Lauwers, J; Van De Klundert, M; Van Haevermaet, H; Van Mechelen, P; Van Remortel, N; Van Spilbeeck, A; Abu Zeid, S; Blekman, F; D'Hondt, J; Daci, N; De Bruyn, I; Deroover, K; Lowette, S; Moortgat, S; Moreels, L; Olbrechts, A; Python, Q; Skovpen, K; Tavernier, S; Van Doninck, W; Van Mulders, P; Van Parijs, I; Brun, H; Clerbaux, B; De Lentdecker, G; Delannoy, H; Fasanella, G; Favart, L; Goldouzian, R; Grebenyuk, A; Karapostoli, G; Lenzi, T; Léonard, A; Luetic, J; Maerschalk, T; Marinov, A; Randle-Conde, A; Seva, T; Vander Velde, C; Vanlaer, P; Vannerom, D; Yonamine, R; Zenoni, F; Zhang, F; Cimmino, A; Cornelis, T; Dobur, D; Fagot, A; Garcia, G; Gul, M; Khvastunov, I; Poyraz, D; Salva, S; Schöfbeck, R; Tytgat, M; Van Driessche, W; Yazgan, E; Zaganidis, N; Bakhshiansohi, H; Beluffi, C; Bondu, O; Brochet, S; Bruno, G; Caudron, A; De Visscher, S; Delaere, C; Delcourt, M; Francois, B; Giammanco, A; Jafari, A; Jez, P; Komm, M; Krintiras, G; Lemaitre, V; Magitteri, A; Mertens, A; Musich, M; Nuttens, C; Piotrzkowski, K; Quertenmont, L; Selvaggi, M; Vidal Marono, M; Wertz, S; Beliy, N; Aldá Júnior, W L; Alves, F L; Alves, G A; Brito, L; Hensel, C; Moraes, A; Pol, M E; Rebello Teles, P; Belchior Batista Das Chagas, E; Carvalho, W; Chinellato, J; Custódio, A; Da Costa, E M; Da Silveira, G G; De Jesus Damiao, D; De Oliveira Martins, C; Fonseca De Souza, S; Huertas Guativa, L M; Malbouisson, H; Matos Figueiredo, D; Mora Herrera, C; Mundim, L; Nogima, H; Prado Da Silva, W L; Santoro, A; Sznajder, A; Tonelli Manganote, E J; Vilela Pereira, A; Ahuja, S; Bernardes, C A; Dogra, S; Tomei, T R Fernandez Perez; Gregores, E M; Mercadante, P G; Moon, C S; Novaes, S F; Padula, Sandra S; Romero Abad, D; Ruiz Vargas, J C; Aleksandrov, A; Hadjiiska, R; Iaydjiev, P; Rodozov, M; Stoykova, S; Sultanov, G; Vutova, M; Dimitrov, A; Glushkov, I; Litov, L; Pavlov, B; Petkov, P; Fang, W; Ahmad, M; Bian, J G; Chen, G M; Chen, H S; Chen, M; Chen, Y; Cheng, T; Jiang, C H; Leggat, D; Liu, Z; Romeo, F; Shaheen, S M; Spiezia, A; Tao, J; Wang, C; Wang, Z; Zhang, H; Zhao, J; Ban, Y; Chen, G; Li, Q; Liu, S; Mao, Y; Qian, S J; Wang, D; Xu, Z; Avila, C; Cabrera, A; Chaparro Sierra, L F; Florez, C; Gomez, J P; González Hernández, C F; Ruiz Alvarez, J D; Sanabria, J C; Godinovic, N; Lelas, D; Puljak, I; Ribeiro Cipriano, P M; Sculac, T; Antunovic, Z; Kovac, M; Brigljevic, V; Ferencek, D; Kadija, K; Mesic, B; Micanovic, S; Sudic, L; Susa, T; Attikis, A; Mavromanolakis, G; Mousa, J; Nicolaou, C; Ptochos, F; Razis, P A; Rykaczewski, H; Tsiakkouri, D; Finger, M; Finger, M; Carrera Jarrin, E; Ellithi Kamel, A; Mahmoud, M A; Radi, A; Kadastik, M; Perrini, L; Raidal, M; Tiko, A; Veelken, C; Eerola, P; Pekkanen, J; Voutilainen, M; Härkönen, J; Järvinen, T; Karimäki, V; Kinnunen, R; Lampén, T; Lassila-Perini, K; Lehti, S; Lindén, T; Luukka, P; Tuominiemi, J; Tuovinen, E; Wendland, L; Talvitie, J; Tuuva, T; Besancon, M; Couderc, F; Dejardin, M; Denegri, D; Fabbro, B; Faure, J L; Favaro, C; Ferri, F; Ganjour, S; Ghosh, S; Givernaud, A; Gras, P; Hamel de Monchenault, G; Jarry, P; Kucher, I; Locci, E; Machet, M; Malcles, J; Rander, J; Rosowsky, A; Titov, M; Zghiche, A; Abdulsalam, A; Antropov, I; Arleo, F; Baffioni, S; Beaudette, F; Busson, P; Cadamuro, L; Chapon, E; Charlot, C; Davignon, O; Granier de Cassagnac, R; Jo, M; Lisniak, S; Martin Blanco, J; Miné, P; Nguyen, M; Ochando, C; Ortona, G; Paganini, P; Pigard, P; Regnard, S; Salerno, R; Sirois, Y; Stahl Leiton, A G; Strebler, T; Yilmaz, Y; Zabi, A; Agram, J-L; Andrea, J; Aubin, A; Bloch, D; Brom, J-M; Buttignol, M; Chabert, E C; Chanon, N; Collard, C; Conte, E; Coubez, X; Fontaine, J-C; Gelé, D; Goerlach, U; Le Bihan, A-C; Van Hove, P; Gadrat, S; Beauceron, S; Bernet, C; Boudoul, G; Carrillo Montoya, C A; Chierici, R; Contardo, D; Courbon, B; Depasse, P; El Mamouni, H; Fan, J; Fay, J; Gascon, S; Gouzevitch, M; Grenier, G; Ille, B; Lagarde, F; Laktineh, I B; Lethuillier, M; Mirabito, L; Pequegnot, A L; Perries, S; Popov, A; Sabes, D; Sordini, V; Vander Donckt, M; Verdier, P; Viret, S; Toriashvili, T; Tsamalaidze, Z; Autermann, C; Beranek, S; Feld, L; Kiesel, M K; Klein, K; Lipinski, M; Preuten, M; Schael, S; Schomakers, C; Schulz, J; Verlage, T; Albert, A; Brodski, M; Dietz-Laursonn, E; Duchardt, D; Endres, M; Erdmann, M; Erdweg, S; Esch, T; Fischer, R; Güth, A; Hamer, M; Hebbeker, T; Heidemann, C; Hoepfner, K; Knutzen, S; Merschmeyer, M; Meyer, A; Millet, P; Mukherjee, S; Olschewski, M; Padeken, K; Pook, T; Radziej, M; Reithler, H; Rieger, M; Scheuch, F; Sonnenschein, L; Teyssier, D; Thüer, S; Cherepanov, V; Flügge, G; Kargoll, B; Kress, T; Künsken, A; Lingemann, J; Müller, T; Nehrkorn, A; Nowack, A; Pistone, C; Pooth, O; Stahl, A; Aldaya Martin, M; Arndt, T; Asawatangtrakuldee, C; Beernaert, K; Behnke, O; Behrens, U; Bin Anuar, A A; Borras, K; Campbell, A; Connor, P; Contreras-Campana, C; Costanza, F; Diez Pardos, C; Dolinska, G; Eckerlin, G; Eckstein, D; Eichhorn, T; Eren, E; Gallo, E; Garay Garcia, J; Geiser, A; Gizhko, A; Grados Luyando, J M; Grohsjean, A; Gunnellini, P; Harb, A; Hauk, J; Hempel, M; Jung, H; Kalogeropoulos, A; Karacheban, O; Kasemann, M; Keaveney, J; Kleinwort, C; Korol, I; Krücker, D; Lange, W; Lelek, A; Leonard, J; Lipka, K; Lobanov, A; Lohmann, W; Mankel, R; Melzer-Pellmann, I-A; Meyer, A B; Mittag, G; Mnich, J; Mussgiller, A; Ntomari, E; Pitzl, D; Placakyte, R; Raspereza, A; Roland, B; Sahin, M Ö; Saxena, P; Schoerner-Sadenius, T; Seitz, C; Spannagel, S; Stefaniuk, N; Van Onsem, G P; Walsh, R; Wissing, C; Blobel, V; Centis Vignali, M; Draeger, A R; Dreyer, T; Garutti, E; Gonzalez, D; Haller, J; Hoffmann, M; Junkes, A; Klanner, R; Kogler, R; Kovalchuk, N; Lapsien, T; Lenz, T; Marchesini, I; Marconi, D; Meyer, M; Niedziela, M; Nowatschin, D; Pantaleo, F; Peiffer, T; Perieanu, A; Poehlsen, J; Sander, C; Scharf, C; Schleper, P; Schmidt, A; Schumann, S; Schwandt, J; Stadie, H; Steinbrück, G; Stober, F M; Stöver, M; Tholen, H; Troendle, D; Usai, E; Vanelderen, L; Vanhoefer, A; Vormwald, B; Akbiyik, M; Barth, C; Baur, S; Baus, C; Berger, J; Butz, E; Caspart, R; Chwalek, T; Colombo, F; De Boer, W; Dierlamm, A; Fink, S; Freund, B; Friese, R; Giffels, M; Gilbert, A; Goldenzweig, P; Haitz, D; Hartmann, F; Heindl, S M; Husemann, U; Katkov, I; Kudella, S; Mildner, H; Mozer, M U; Müller, Th; Plagge, M; Quast, G; Rabbertz, K; Röcker, S; Roscher, F; Schröder, M; Shvetsov, I; Sieber, G; Simonis, H J; Ulrich, R; Wayand, S; Weber, M; Weiler, T; Williamson, S; Wöhrmann, C; Wolf, R; Anagnostou, G; Daskalakis, G; Geralis, T; Giakoumopoulou, V A; Kyriakis, A; Loukas, D; Topsis-Giotis, I; Kesisoglou, S; Panagiotou, A; Saoulidou, N; Tziaferi, E; Evangelou, I; Flouris, G; Foudas, C; Kokkas, P; Loukas, N; Manthos, N; Papadopoulos, I; Paradas, E; Filipovic, N; Bencze, G; Hajdu, C; Horvath, D; Sikler, F; Veszpremi, V; Vesztergombi, G; Zsigmond, A J; Beni, N; Czellar, S; Karancsi, J; Makovec, A; Molnar, J; Szillasi, Z; Bartók, M; Raics, P; Trocsanyi, Z L; Ujvari, B; Bahinipati, S; Choudhury, S; Mal, P; Mandal, K; Nayak, A; Sahoo, D K; Sahoo, N; Swain, S K; Bansal, S; Beri, S B; Bhatnagar, V; Chawla, R; Bhawandeep, U; Kalsi, A K; Kaur, A; Kaur, M; Kumar, R; Kumari, P; Mehta, A; Mittal, M; Singh, J B; Walia, G; Kumar, Ashok; Bhardwaj, A; Choudhary, B C; Garg, R B; Keshri, S; Malhotra, S; Naimuddin, M; Nishu, N; Ranjan, K; Sharma, R; Sharma, V; Bhattacharya, R; Bhattacharya, S; Chatterjee, K; Dey, S; Dutt, S; Dutta, S; Ghosh, S; Majumdar, N; Modak, A; Mondal, K; Mukhopadhyay, S; Nandan, S; Purohit, A; Roy, A; Roy, D; Roy Chowdhury, S; Sarkar, S; Sharan, M; Thakur, S; Behera, P K; Chudasama, R; Dutta, D; Jha, V; Kumar, V; Mohanty, A K; Netrakanti, P K; Pant, L M; Shukla, P; Topkar, A; Aziz, T; Dugad, S; Kole, G; Mahakud, B; Mitra, S; Mohanty, G B; Parida, B; Sur, N; Sutar, B; Banerjee, S; Bhowmik, S; Dewanjee, R K; Ganguly, S; Guchait, M; Jain, Sa; Kumar, S; Maity, M; Majumder, G; Mazumdar, K; Sarkar, T; Wickramage, N; Chauhan, S; Dube, S; Hegde, V; Kapoor, A; Kothekar, K; Pandey, S; Rane, A; Sharma, S; Chenarani, S; Eskandari Tadavani, E; Etesami, S M; Fahim, A; Khakzad, M; Mohammadi Najafabadi, M; Naseri, M; Paktinat Mehdiabadi, S; Rezaei Hosseinabadi, F; Safarzadeh, B; Zeinali, M; Felcini, M; Grunewald, M; Abbrescia, M; Calabria, C; Caputo, C; Colaleo, A; Creanza, D; Cristella, L; De Filippis, N; De Palma, M; Fiore, L; Iaselli, G; Maggi, G; Maggi, M; Miniello, G; My, S; Nuzzo, S; Pompili, A; Pugliese, G; Radogna, R; Ranieri, A; Selvaggi, G; Sharma, A; Silvestris, L; Venditti, R; Verwilligen, P; Abbiendi, G; Battilana, C; Bonacorsi, D; Braibant-Giacomelli, S; Brigliadori, L; Campanini, R; Capiluppi, P; Castro, A; Cavallo, F R; Chhibra, S S; Codispoti, G; Cuffiani, M; Dallavalle, G M; Fabbri, F; Fanfani, A; Fasanella, D; Giacomelli, P; Grandi, C; Guiducci, L; Marcellini, S; Masetti, G; Montanari, A; Navarria, F L; Perrotta, A; Rossi, A M; Rovelli, T; Siroli, G P; Tosi, N; Albergo, S; Costa, S; Di Mattia, A; Giordano, F; Potenza, R; Tricomi, A; Tuve, C; Barbagli, G; Ciulli, V; Civinini, C; D'Alessandro, R; Focardi, E; Lenzi, P; Meschini, M; Paoletti, S; Sguazzoni, G; Viliani, L; Benussi, L; Bianco, S; Fabbri, F; Piccolo, D; Primavera, F; Calvelli, V; Ferro, F; Lo Vetere, M; Monge, M R; Robutti, E; Tosi, S; Brianza, L; Brivio, F; Dinardo, M E; Fiorendi, S; Gennai, S; Ghezzi, A; Govoni, P; Malberti, M; Malvezzi, S; Manzoni, R A; Menasce, D; Moroni, L; Paganoni, M; Pedrini, D; Pigazzini, S; Ragazzi, S; Tabarelli de Fatis, T; Buontempo, S; Cavallo, N; De Nardo, G; Di Guida, S; Esposito, M; Fabozzi, F; Fienga, F; Iorio, A O M; Lanza, G; Lista, L; Meola, S; Paolucci, P; Sciacca, C; Thyssen, F; Azzi, P; Bacchetta, N; Benato, L; Bisello, D; Boletti, A; Carlin, R; Carvalho Antunes De Oliveira, A; Checchia, P; Dall'Osso, M; De Castro Manzano, P; Dorigo, T; Dosselli, U; Gasparini, F; Gasparini, U; Gozzelino, A; Lacaprara, S; Margoni, M; Meneguzzo, A T; Pazzini, J; Pozzobon, N; Ronchese, P; Simonetto, F; Torassa, E; Zanetti, M; Zotto, P; Zumerle, G; Braghieri, A; Magnani, A; Montagna, P; Ratti, S P; Re, V; Riccardi, C; Salvini, P; Vai, I; Vitulo, P; Alunni Solestizi, L; Bilei, G M; Ciangottini, D; Fanò, L; Lariccia, P; Leonardi, R; Mantovani, G; Menichelli, M; Saha, A; Santocchia, A; Androsov, K; Azzurri, P; Bagliesi, G; Bernardini, J; Boccali, T; Castaldi, R; Ciocci, M A; Dell'Orso, R; Donato, S; Fedi, G; Giassi, A; Grippo, M T; Ligabue, F; Lomtadze, T; Martini, L; Messineo, A; Palla, F; Rizzi, A; Savoy-Navarro, A; Spagnolo, P; Tenchini, R; Tonelli, G; Venturi, A; Verdini, P G; Barone, L; Cavallari, F; Cipriani, M; Del Re, D; Diemoz, M; Gelli, S; Longo, E; Margaroli, F; Marzocchi, B; Meridiani, P; Organtini, G; Paramatti, R; Preiato, F; Rahatlou, S; Rovelli, C; Santanastasio, F; Amapane, N; Arcidiacono, R; Argiro, S; Arneodo, M; Bartosik, N; Bellan, R; Biino, C; Cartiglia, N; Cenna, F; Costa, M; Covarelli, R; Degano, A; Demaria, N; Finco, L; Kiani, B; Mariotti, C; Maselli, S; Migliore, E; Monaco, V; Monteil, E; Monteno, M; Obertino, M M; Pacher, L; Pastrone, N; Pelliccioni, M; Pinna Angioni, G L; Ravera, F; Romero, A; Ruspa, M; Sacchi, R; Shchelina, K; Sola, V; Solano, A; Staiano, A; Traczyk, P; Belforte, S; Casarsa, M; Cossutti, F; Della Ricca, G; Zanetti, A; Kim, D H; Kim, G N; Kim, M S; Lee, S; Lee, S W; Oh, Y D; Sekmen, S; Son, D C; Yang, Y C; Lee, A; Kim, H; Brochero Cifuentes, J A; Kim, T J; Cho, S; Choi, S; Go, Y; Gyun, D; Ha, S; Hong, B; Jo, Y; Kim, Y; Lee, B; Lee, K; Lee, K S; Lee, S; Lim, J; Park, S K; Roh, Y; Almond, J; Kim, J; Lee, H; Oh, S B; Radburn-Smith, B C; Seo, S H; Yang, U K; Yoo, H D; Yu, G B; Choi, M; Kim, H; Kim, J H; Lee, J S H; Park, I C; Ryu, G; Ryu, M S; Choi, Y; Goh, J; Hwang, C; Lee, J; Yu, I; Dudenas, V; Juodagalvis, A; Vaitkus, J; Ahmed, I; Ibrahim, Z A; Komaragiri, J R; Md Ali, M A B; Mohamad Idris, F; Wan Abdullah, W A T; Yusli, M N; Zolkapli, Z; Castilla-Valdez, H; De La Cruz-Burelo, E; Heredia-De La Cruz, I; Hernandez-Almada, A; Lopez-Fernandez, R; Magaña Villalba, R; Mejia Guisao, J; Sanchez-Hernandez, A; Carrillo Moreno, S; Oropeza Barrera, C; Vazquez Valencia, F; Carpinteyro, S; Pedraza, I; Salazar Ibarguen, H A; Uribe Estrada, C; Morelos Pineda, A; Krofcheck, D; Butler, P H; Ahmad, A; Ahmad, M; Hassan, Q; Hoorani, H R; Khan, W A; Saddique, A; Shah, M A; Shoaib, M; Waqas, M; Bialkowska, H; Bluj, M; Boimska, B; Frueboes, T; Górski, M; Kazana, M; Nawrocki, K; Romanowska-Rybinska, K; Szleper, M; Zalewski, P; Bunkowski, K; Byszuk, A; Doroba, K; Kalinowski, A; Konecki, M; Krolikowski, J; Misiura, M; Olszewski, M; Walczak, M; Bargassa, P; Beirão Da Cruz E Silva, C; Calpas, B; Di Francesco, A; Faccioli, P; Ferreira Parracho, P G; Gallinaro, M; Hollar, J; Leonardo, N; Lloret Iglesias, L; Nemallapudi, M V; Rodrigues Antunes, J; Seixas, J; Toldaiev, O; Vadruccio, D; Varela, J; Vischia, P; Afanasiev, S; Bunin, P; Gavrilenko, M; Golutvin, I; Gorbunov, I; Kamenev, A; Karjavin, V; Lanev, A; Malakhov, A; Matveev, V; Palichik, V; Perelygin, V; Shmatov, S; Shulha, S; Skatchkov, N; Smirnov, V; Voytishin, N; Zarubin, A; Chtchipounov, L; Golovtsov, V; Ivanov, Y; Kim, V; Kuznetsova, E; Murzin, V; Oreshkin, V; Sulimov, V; Vorobyev, A; Andreev, Yu; Dermenev, A; Gninenko, S; Golubev, N; Karneyeu, A; Kirsanov, M; Krasnikov, N; Pashenkov, A; Tlisov, D; Toropin, A; Epshteyn, V; Gavrilov, V; Lychkovskaya, N; Popov, V; Pozdnyakov, I; Safronov, G; Spiridonov, A; Toms, M; Vlasov, E; Zhokin, A; Bylinkin, A; Chistov, R; Markin, O; Polikarpov, S; Andreev, V; Azarkin, M; Dremin, I; Kirakosyan, M; Leonidov, A; Terkulov, A; Baskakov, A; Belyaev, A; Boos, E; Ershov, A; Gribushin, A; Kaminskiy, A; Kodolova, O; Korotkikh, V; Lokhtin, I; Miagkov, I; Obraztsov, S; Petrushanko, S; Savrin, V; Snigirev, A; Vardanyan, I; Blinov, V; Skovpen, Y; Shtol, D; Azhgirey, I; Bayshev, I; Bitioukov, S; Elumakhov, D; Kachanov, V; Kalinin, A; Konstantinov, D; Krychkine, V; Petrov, V; Ryutin, R; Sobol, A; Troshin, S; Tyurin, N; Uzunian, A; Volkov, A; Adzic, P; Cirkovic, P; Devetak, D; Dordevic, M; Milosevic, J; Rekovic, V; Alcaraz Maestre, J; Barrio Luna, M; Calvo, E; Cerrada, M; Chamizo Llatas, M; Colino, N; De La Cruz, B; Delgado Peris, A; Escalante Del Valle, A; Fernandez Bedoya, C; Fernández Ramos, J P; Flix, J; Fouz, M C; Garcia-Abia, P; Gonzalez Lopez, O; Goy Lopez, S; Hernandez, J M; Josa, M I; Navarro De Martino, E; Pérez-Calero Yzquierdo, A; Puerta Pelayo, J; Quintario Olmeda, A; Redondo, I; Romero, L; Soares, M S; de Trocóniz, J F; Missiroli, M; Moran, D; Cuevas, J; Fernandez Menendez, J; Gonzalez Caballero, I; González Fernández, J R; Palencia Cortezon, E; Sanchez Cruz, S; Suárez Andrés, I; Vizan Garcia, J M; Cabrillo, I J; Calderon, A; Castiñeiras De Saa, J R; Curras, E; Fernandez, M; Garcia-Ferrero, J; Gomez, G; Lopez Virto, A; Marco, J; Martinez Rivero, C; Matorras, F; Piedra Gomez, J; Rodrigo, T; Ruiz-Jimeno, A; Scodellaro, L; Trevisani, N; Vila, I; Vilar Cortabitarte, R; Abbaneo, D; Auffray, E; Auzinger, G; Bachtis, M; Baillon, P; Ball, A H; Barney, D; Bloch, P; Bocci, A; Bonato, A; Botta, C; Camporesi, T; Castello, R; Cepeda, M; Cerminara, G; d'Enterria, D; Dabrowski, A; Daponte, V; David, A; De Gruttola, M; De Roeck, A; Di Marco, E; Dobson, M; Dorney, B; du Pree, T; Duggan, D; Dünser, M; Dupont, N; Elliott-Peisert, A; Everaerts, P; Fartoukh, S; Franzoni, G; Fulcher, J; Funk, W; Gigi, D; Gill, K; Girone, M; Glege, F; Gulhan, D; Gundacker, S; Guthoff, M; Hammer, J; Harris, P; Hegeman, J; Innocente, V; Janot, P; Kieseler, J; Kirschenmann, H; Knünz, V; Kornmayer, A; Kortelainen, M J; Kousouris, K; Krammer, M; Lange, C; Lecoq, P; Lourenço, C; Lucchini, M T; Malgeri, L; Mannelli, M; Martelli, A; Meijers, F; Merlin, J A; Mersi, S; Meschi, E; Milenovic, P; Moortgat, F; Morovic, S; Mulders, M; Neugebauer, H; Orfanelli, S; Orsini, L; Pape, L; Perez, E; Peruzzi, M; Petrilli, A; Petrucciani, G; Pfeiffer, A; Pierini, M; Racz, A; Reis, T; Rolandi, G; Rovere, M; Ruan, M; Sakulin, H; Sauvan, J B; Schäfer, C; Schwick, C; Seidel, M; Sharma, A; Silva, P; Sphicas, P; Steggemann, J; Stoye, M; Takahashi, Y; Tosi, M; Treille, D; Triossi, A; Tsirou, A; Veckalns, V; Veres, G I; Verweij, M; Wardle, N; Wöhri, H K; Zagozdzinska, A; Zeuner, W D; Bertl, W; Deiters, K; Erdmann, W; Horisberger, R; Ingram, Q; Kaestli, H C; Kotlinski, D; Langenegger, U; Rohe, T; Bachmair, F; Bäni, L; Bianchini, L; Casal, B; Dissertori, G; Dittmar, M; Donegà, M; Grab, C; Heidegger, C; Hits, D; Hoss, J; Kasieczka, G; Lecomte, P; Lustermann, W; Mangano, B; Marionneau, M; Martinez Ruiz Del Arbol, P; Masciovecchio, M; Meinhard, M T; Meister, D; Micheli, F; Musella, P; Nessi-Tedaldi, F; Pandolfi, F; Pata, J; Pauss, F; Perrin, G; Perrozzi, L; Quittnat, M; Rossini, M; Schönenberger, M; Starodumov, A; Tavolaro, V R; Theofilatos, K; Wallny, R; Aarrestad, T K; Amsler, C; Caminada, L; Canelli, M F; De Cosa, A; Galloni, C; Hinzmann, A; Hreus, T; Kilminster, B; Ngadiuba, J; Pinna, D; Rauco, G; Robmann, P; Salerno, D; Yang, Y; Zucchetta, A; Candelise, V; Doan, T H; Jain, Sh; Khurana, R; Konyushikhin, M; Kuo, C M; Lin, W; Lu, Y J; Pozdnyakov, A; Yu, S S; Kumar, Arun; Chang, P; Chang, Y H; Chang, Y W; Chao, Y; Chen, K F; Chen, P H; Dietz, C; Fiori, F; Hou, W-S; Hsiung, Y; Liu, Y F; Lu, R-S; Miñano Moya, M; Paganis, E; Psallidas, A; Tsai, J F; Tzeng, Y M; Asavapibhop, B; Singh, G; Srimanobhas, N; Suwonjandee, N; Adiguzel, A; Cerci, S; Damarseckin, S; Demiroglu, Z S; Dozen, C; Dumanoglu, I; Girgis, S; Gokbulut, G; Guler, Y; Hos, I; Kangal, E E; Kara, O; Kayis Topaksu, A; Kiminsu, U; Oglakci, M; Onengut, G; Ozdemir, K; Sunar Cerci, D; Tali, B; Turkcapar, S; Zorbakir, I S; Zorbilmez, C; Bilin, B; Bilmis, S; Isildak, B; Karapinar, G; Yalvac, M; Zeyrek, M; Gülmez, E; Kaya, M; Kaya, O; Yetkin, E A; Yetkin, T; Cakir, A; Cankocak, K; Sen, S; Grynyov, B; Levchuk, L; Sorokin, P; Aggleton, R; Ball, F; Beck, L; Brooke, J J; Burns, D; Clement, E; Cussans, D; Flacher, H; Goldstein, J; Grimes, M; Heath, G P; Heath, H F; Jacob, J; Kreczko, L; Lucas, C; Newbold, D M; Paramesvaran, S; Poll, A; Sakuma, T; Seif El Nasr-Storey, S; Smith, D; Smith, V J; Belyaev, A; Brew, C; Brown, R M; Calligaris, L; Cieri, D; Cockerill, D J A; Coughlan, J A; Harder, K; Harper, S; Olaiya, E; Petyt, D; Shepherd-Themistocleous, C H; Thea, A; Tomalin, I R; Williams, T; Baber, M; Bainbridge, R; Buchmuller, O; Bundock, A; Burton, D; Casasso, S; Citron, M; Colling, D; Corpe, L; Dauncey, P; Davies, G; De Wit, A; Della Negra, M; Di Maria, R; Dunne, P; Elwood, A; Futyan, D; Haddad, Y; Hall, G; Iles, G; James, T; Lane, R; Laner, C; Lucas, R; Lyons, L; Magnan, A-M; Malik, S; Mastrolorenzo, L; Nash, J; Nikitenko, A; Pela, J; Penning, B; Pesaresi, M; Raymond, D M; Richards, A; Rose, A; Seez, C; Summers, S; Tapper, A; Uchida, K; Vazquez Acosta, M; Virdee, T; Wright, J; Zenz, S C; Cole, J E; Hobson, P R; Khan, A; Kyberd, P; Leslie, D; Reid, I D; Symonds, P; Teodorescu, L; Turner, M; Borzou, A; Call, K; Dittmann, J; Hatakeyama, K; Liu, H; Pastika, N; Cooper, S I; Henderson, C; Rumerio, P; West, C; Arcaro, D; Avetisyan, A; Bose, T; Gastler, D; Rankin, D; Richardson, C; Rohlf, J; Sulak, L; Zou, D; Benelli, G; Berry, E; Cutts, D; Garabedian, A; Hakala, J; Heintz, U; Hogan, J M; Jesus, O; Kwok, K H M; Laird, E; Landsberg, G; Mao, Z; Narain, M; Piperov, S; Sagir, S; Spencer, E; Syarif, R; Breedon, R; Breto, G; Burns, D; Calderon De La Barca Sanchez, M; Chauhan, S; Chertok, M; Conway, J; Conway, R; Cox, P T; Erbacher, R; Flores, C; Funk, G; Gardner, M; Ko, W; Lander, R; Mclean, C; Mulhearn, M; Pellett, D; Pilot, J; Shalhout, S; Smith, J; Squires, M; Stolp, D; Tripathi, M; Bravo, C; Cousins, R; Dasgupta, A; Florent, A; Hauser, J; Ignatenko, M; Mccoll, N; Saltzberg, D; Schnaible, C; Takasugi, E; Valuev, V; Weber, M; Bouvier, E; Burt, K; Clare, R; Ellison, J; Gary, J W; Ghiasi Shirazi, S M A; Hanson, G; Heilman, J; Jandir, P; Kennedy, E; Lacroix, F; Long, O R; Olmedo Negrete, M; Paneva, M I; Shrinivas, A; Si, W; Wei, H; Wimpenny, S; Yates, B R; Branson, J G; Cerati, G B; Cittolin, S; Derdzinski, M; Gerosa, R; Holzner, A; Klein, D; Krutelyov, V; Letts, J; Macneill, I; Olivito, D; Padhi, S; Pieri, M; Sani, M; Sharma, V; Simon, S; Tadel, M; Vartak, A; Wasserbaech, S; Welke, C; Wood, J; Würthwein, F; Yagil, A; Zevi Della Porta, G; Amin, N; Bhandari, R; Bradmiller-Feld, J; Campagnari, C; Dishaw, A; Dutta, V; Franco Sevilla, M; George, C; Golf, F; Gouskos, L; Gran, J; Heller, R; Incandela, J; Mullin, S D; Ovcharova, A; Qu, H; Richman, J; Stuart, D; Suarez, I; Yoo, J; Anderson, D; Bendavid, J; Bornheim, A; Bunn, J; Chen, Y; Duarte, J; Lawhorn, J M; Mott, A; Newman, H B; Pena, C; Spiropulu, M; Vlimant, J R; Xie, S; Zhu, R Y; Andrews, M B; Ferguson, T; Paulini, M; Russ, J; Sun, M; Vogel, H; Vorobiev, I; Weinberg, M; Cumalat, J P; Ford, W T; Jensen, F; Johnson, A; Krohn, M; Mulholland, T; Stenson, K; Wagner, S R; Alexander, J; Chaves, J; Chu, J; Dittmer, S; Mcdermott, K; Mirman, N; Nicolas Kaufman, G; Patterson, J R; Rinkevicius, A; Ryd, A; Skinnari, L; Soffi, L; Tan, S M; Tao, Z; Thom, J; Tucker, J; Wittich, P; Zientek, M; Winn, D; Abdullin, S; Albrow, M; Apollinari, G; Apresyan, A; Banerjee, S; Bauerdick, L A T; Beretvas, A; Berryhill, J; Bhat, P C; Bolla, G; Burkett, K; Butler, J N; Cheung, H W K; Chlebana, F; Cihangir, S; Cremonesi, M; Elvira, V D; Fisk, I; Freeman, J; Gottschalk, E; Gray, L; Green, D; Grünendahl, S; Gutsche, O; Hare, D; Harris, R M; Hasegawa, S; Hirschauer, J; Hu, Z; Jayatilaka, B; Jindariani, S; Johnson, M; Joshi, U; Klima, B; Kreis, B; Lammel, S; Linacre, J; Lincoln, D; Lipton, R; Liu, M; Liu, T; Lopes De Sá, R; Lykken, J; Maeshima, K; Magini, N; Marraffino, J M; Maruyama, S; Mason, D; McBride, P; Merkel, P; Mrenna, S; Nahn, S; O'Dell, V; Pedro, K; Prokofyev, O; Rakness, G; Ristori, L; Sexton-Kennedy, E; Soha, A; Spalding, W J; Spiegel, L; Stoynev, S; Strait, J; Strobbe, N; Taylor, L; Tkaczyk, S; Tran, N V; Uplegger, L; Vaandering, E W; Vernieri, C; Verzocchi, M; Vidal, R; Wang, M; Weber, H A; Whitbeck, A; Wu, Y; Acosta, D; Avery, P; Bortignon, P; Bourilkov, D; Brinkerhoff, A; Carnes, A; Carver, M; Curry, D; Das, S; Field, R D; Furic, I K; Konigsberg, J; Korytov, A; Low, J F; Ma, P; Matchev, K; Mei, H; Mitselmakher, G; Rank, D; Shchutska, L; Sperka, D; Thomas, L; Wang, J; Wang, S; Yelton, J; Linn, S; Markowitz, P; Martinez, G; Rodriguez, J L; Ackert, A; Adams, J R; Adams, T; Askew, A; Bein, S; Diamond, B; Hagopian, S; Hagopian, V; Johnson, K F; Prosper, H; Santra, A; Yohay, R; Baarmand, M M; Bhopatkar, V; Colafranceschi, S; Hohlmann, M; Noonan, D; Roy, T; Yumiceva, F; Adams, M R; Apanasevich, L; Berry, D; Betts, R R; Bucinskaite, I; Cavanaugh, R; Evdokimov, O; Gauthier, L; Gerber, C E; Hofman, D J; Jung, K; Kurt, P; O'Brien, C; Sandoval Gonzalez, I D; Turner, P; Varelas, N; Wang, H; Wu, Z; Zakaria, M; Zhang, J; Bilki, B; Clarida, W; Dilsiz, K; Durgut, S; Gandrajula, R P; Haytmyradov, M; Khristenko, V; Merlo, J-P; Mermerkaya, H; Mestvirishvili, A; Moeller, A; Nachtman, J; Ogul, H; Onel, Y; Ozok, F; Penzo, A; Snyder, C; Tiras, E; Wetzel, J; Yi, K; Anderson, I; Blumenfeld, B; Cocoros, A; Eminizer, N; Fehling, D; Feng, L; Gritsan, A V; Maksimovic, P; Martin, C; Osherson, M; Roskes, J; Sarica, U; Swartz, M; Xiao, M; Xin, Y; You, C; Al-Bataineh, A; Baringer, P; Bean, A; Boren, S; Bowen, J; Bruner, C; Castle, J; Forthomme, L; Kenny, R P; Khalil, S; Kropivnitskaya, A; Majumder, D; Mcbrayer, W; Murray, M; Sanders, S; Stringer, R; Tapia Takaki, J D; Wang, Q; Ivanov, A; Kaadze, K; Maravin, Y; Mohammadi, A; Saini, L K; Skhirtladze, N; Toda, S; Rebassoo, F; Wright, D; Anelli, C; Baden, A; Baron, O; Belloni, A; Calvert, B; Eno, S C; Ferraioli, C; Gomez, J A; Hadley, N J; Jabeen, S; Kellogg, R G; Kolberg, T; Kunkle, J; Lu, Y; Mignerey, A C; Ricci-Tam, F; Shin, Y H; Skuja, A; Tonjes, M B; Tonwar, S C; Abercrombie, D; Allen, B; Apyan, A; Azzolini, V; Barbieri, R; Baty, A; Bi, R; Bierwagen, K; Brandt, S; Busza, W; Cali, I A; D'Alfonso, M; Demiragli, Z; Di Matteo, L; Gomez Ceballos, G; Goncharov, M; Hsu, D; Iiyama, Y; Innocenti, G M; Klute, M; Kovalskyi, D; Krajczar, K; Lai, Y S; Lee, Y-J; Levin, A; Luckey, P D; Maier, B; Marini, A C; Mcginn, C; Mironov, C; Narayanan, S; Niu, X; Paus, C; Roland, C; Roland, G; Salfeld-Nebgen, J; Stephans, G S F; Tatar, K; Varma, M; Velicanu, D; Veverka, J; Wang, J; Wang, T W; Wyslouch, B; Yang, M; Zhukova, V; Benvenuti, A C; Chatterjee, R M; Evans, A; Finkel, A; Gude, A; Hansen, P; Kalafut, S; Kao, S C; Kubota, Y; Lesko, Z; Mans, J; Nourbakhsh, S; Ruckstuhl, N; Rusack, R; Tambe, N; Turkewitz, J; Acosta, J G; Oliveros, S; Avdeeva, E; Bartek, R; Bloom, K; Claes, D R; Dominguez, A; Fangmeier, C; Gonzalez Suarez, R; Kamalieddin, R; Kravchenko, I; Malta Rodrigues, A; Meier, F; Monroy, J; Siado, J E; Snow, G R; Stieger, B; Alyari, M; Dolen, J; George, J; Godshalk, A; Harrington, C; Iashvili, I; Kaisen, J; Kharchilava, A; Kumar, A; Parker, A; Rappoccio, S; Roozbahani, B; Alverson, G; Barberis, E; Hortiangtham, A; Massironi, A; Morse, D M; Nash, D; Orimoto, T; Teixeira De Lima, R; Trocino, D; Wang, R-J; Wood, D; Bhattacharya, S; Charaf, O; Hahn, K A; Kubik, A; Kumar, A; Mucia, N; Odell, N; Pollack, B; Schmitt, M H; Sung, K; Trovato, M; Velasco, M; Dev, N; Hildreth, M; Hurtado Anampa, K; Jessop, C; Karmgard, D J; Kellams, N; Lannon, K; Marinelli, N; Meng, F; Mueller, C; Musienko, Y; Planer, M; Reinsvold, A; Ruchti, R; Smith, G; Taroni, S; Wayne, M; Wolf, M; Woodard, A; Alimena, J; Antonelli, L; Bylsma, B; Durkin, L S; Flowers, S; Francis, B; Hart, A; Hill, C; Hughes, R; Ji, W; Liu, B; Luo, W; Puigh, D; Winer, B L; Wulsin, H W; Cooperstein, S; Driga, O; Elmer, P; Hardenbrook, J; Hebda, P; Lange, D; Luo, J; Marlow, D; Medvedeva, T; Mei, K; Mooney, M; Olsen, J; Palmer, C; Piroué, P; Stickland, D; Svyatkovskiy, A; Tully, C; Zuranski, A; Malik, S; Barker, A; Barnes, V E; Folgueras, S; Gutay, L; Jha, M K; Jones, M; Jung, A W; Khatiwada, A; Miller, D H; Neumeister, N; Schulte, J F; Shi, X; Sun, J; Wang, F; Xie, W; Parashar, N; Stupak, J; Adair, A; Akgun, B; Chen, Z; Ecklund, K M; Geurts, F J M; Guilbaud, M; Li, W; Michlin, B; Northup, M; Padley, B P; Redjimi, R; Roberts, J; Rorie, J; Tu, Z; Zabel, J; Betchart, B; Bodek, A; de Barbaro, P; Demina, R; Duh, Y T; Ferbel, T; Galanti, M; Garcia-Bellido, A; Han, J; Hindrichs, O; Khukhunaishvili, A; Lo, K H; Tan, P; Verzetti, M; Agapitos, A; Chou, J P; Contreras-Campana, E; Gershtein, Y; Gómez Espinosa, T A; Halkiadakis, E; Heindl, M; Hidas, D; Hughes, E; Kaplan, S; Kunnawalkam Elayavalli, R; Kyriacou, S; Lath, A; Nash, K; Saka, H; Salur, S; Schnetzer, S; Sheffield, D; Somalwar, S; Stone, R; Thomas, S; Thomassen, P; Walker, M; Delannoy, A G; Foerster, M; Heideman, J; Riley, G; Rose, K; Spanier, S; Thapa, K; Bouhali, O; Celik, A; Dalchenko, M; De Mattia, M; Delgado, A; Dildick, S; Eusebi, R; Gilmore, J; Huang, T; Juska, E; Kamon, T; Mueller, R; Pakhotin, Y; Patel, R; Perloff, A; Perniè, L; Rathjens, D; Rose, A; Safonov, A; Tatarinov, A; Ulmer, K A; Akchurin, N; Cowden, C; Damgov, J; De Guio, F; Dragoiu, C; Dudero, P R; Faulkner, J; Gurpinar, E; Kunori, S; Lamichhane, K; Lee, S W; Libeiro, T; Peltola, T; Undleeb, S; Volobouev, I; Wang, Z; Greene, S; Gurrola, A; Janjam, R; Johns, W; Maguire, C; Melo, A; Ni, H; Sheldon, P; Tuo, S; Velkovska, J; Xu, Q; Arenton, M W; Barria, P; Cox, B; Goodell, J; Hirosky, R; Ledovskoy, A; Li, H; Neu, C; Sinthuprasith, T; Sun, X; Wang, Y; Wolfe, E; Xia, F; Clarke, C; Harr, R; Karchin, P E; Sturdy, J; Belknap, D A; Buchanan, J; Caillol, C; Dasu, S; Dodd, L; Duric, S; Gomber, B; Grothe, M; Herndon, M; Hervé, A; Klabbers, P; Lanaro, A; Levine, A; Long, K; Loveless, R; Ojalvo, I; Perry, T; Pierro, G A; Polese, G; Ruggles, T; Savin, A; Smith, N; Smith, W H; Taylor, D; Woods, N

2017-04-21

The relative modification of the prompt ψ(2S) and J/ψ yields from pp to PbPb collisions, at the center-of-mass energy of 5.02 TeV per nucleon pair, is presented. The analysis is based on pp and PbPb data samples collected by the CMS experiment at the LHC in 2015, corresponding to integrated luminosities of 28.0  pb^{-1} and 464  μb^{-1}, respectively. The double ratio of measured yields of prompt charmonia reconstructed through their decays into muon pairs, (N_{ψ(2S)}/N_{J/ψ})_{PbPb}/(N_{ψ(2S)}/N_{J/ψ})_{pp}, is determined as a function of PbPb collision centrality and charmonium transverse momentum p_{T}, in two kinematic intervals: |y|<1.6 covering 6.5

An Introduction to Structural Reliability Theory

DTIC Science & Technology

1989-01-01

Test Samples psi COV Distribution Remarks Yield stress 66 (XX 0.09 assumed lognormal mill test I containment vesel SA537 GrB Yield stress 󈧗 6W8...straightened shape Tension :32 57.909 0.089 cold straightened shape Tension 9 84.039 0.1124 annealed , alloy steel Tension 9 124,9 0.1796 . quenched...alloys, annealed and quenched, and drawn samples Tension 22 29.50 X 103 0.0072 .. structural steel Compression 22 29.49 X 103 0.0146 ... structural

Acute corticospinal and spinal modulation after whole body vibration

PubMed Central

Krause, A.; Gollhofer, A.; Freyler, K.; Jablonka, L.; Ritzmann, R.

2016-01-01

Objectives: The objective of this study was to investigate neural effects of acute whole body vibration (WBV) on lower limb muscles regarding corticospinal and spinal excitability. Methods: In 44 healthy subjects (16 f/ 28 m), motor evoked potentials (MEP) and H-reflexes in m. soleus (SOL) and gastrocnemius medialis (GM) were elicited before (t1), immediately after (t2), 2 (t3), 4 (t4) and 10 min after (t5) WBV. Results: After WBV, MEP amplitudes were significantly increased in SOL (t2+15±30%, t3+22±32%, t4+15±35%, t5+20±30%, P<0.05), but not in GM (t2+32±62%, t3+9±35%, t4+8±36%, t5+22±47%; P=0.07). Contrarily, H-reflexes were significantly reduced in SOL (t2-19±28%, t3-21±22%, t4-20±21%, t5-14±28%, P<0.05) and GM (t2-14±37%, t3-16±25%, t4-18±29%, t5-16±28%, P<0.05). Conclusions: A temporary sustained enhancement of corticospinal excitability concomitant with spinal inhibition after WBV points towards persisting neural modulation in the central nervous system. This could indicate greater neural modulation over M1 and descending pathways, while the contribution of spinal pathways is reduced. PMID:27973385

Addendum 1, to Resource Conservation and Recovery Act (RCRA) Facility Investigation R Report for IRP Sites Number’s 17, 18, 19 and 21. Volume 2. Appendices A-L. 148th Fighter Group, Minnesota Air National Guard Duluth Air National Guard Base, Duluth, Minnesota.

DTIC Science & Technology

1996-03-01

1224 1-3:8 AMLSSa IS j 57D .J.q IN1TE~RNAL rEriP 31 OL’LL’Tr, RNGS 2.1- 2.3 us PH0P HOTOU9n POOUl ST’lF3. -ý ED= rAwiAE SEr T .2Er.t SAM’PLE LISR !ARr...I JUL 23 133,2 12:22 IN TERNA5L Tr • ? 𔃽 OULU T , ir1Q4G G I g (M L LIRRYIImrPLE LIBRARY I JUL 22 1.1-, 12,12 ARNILE LISR /RT 2 JUL 221 2-3. 1211.3...0 =UP ACI i-ITrEN 1 31212. 2 rI𔃼 aS,~~ -102.5 100.2 rro SAMLE LISR PRY I JUL 23 ISlt 19252 PNL SIs a 2 1 J BYRD, JR. 1r•T RNAL TEIP 235 PULUTM RriGs

Effect of non-metallic precipitates and grain size on core loss of non-oriented electrical silicon steels

NASA Astrophysics Data System (ADS)

Wang, Jiayi; Ren, Qiang; Luo, Yan; Zhang, Lifeng

2018-04-01

In the current study, the number density and size of non-metallic precipitates and the size of grains on the core loss of the 50W800 non-oriented electrical silicon steel sheets were investigated. The number density and size of precipitates and grains were statistically analyzed using an automatic scanning electron microscope (ASPEX) and an optical microscope. Hypothesis models were established to reveal the physical feature for the function of grain size and precipitates on the core loss of the steel. Most precipitates in the steel were AlN particles smaller than 1 μm so that were detrimental to the core loss of the steel. These finer AlN particles distributed on the surface of the steel sheet. The relationship between the number density of precipitates (x in number/mm2 steel area) and the core loss (P1.5/50 in W/kg) was regressed as P1.5/50 = 4.150 + 0.002 x. The average grain size was approximately 25-35 μm. The relationship between the core loss and grain size (d in μm) was P1.5/50 = 3.851 + 20.001 d-1 + 60.000 d-2.

Effect of KH2PO4 on gene expression, morphological and biochemical characteristics of stevia rebaudiana Bertoni under in vitro conditions.

PubMed

Kahrizi, D; Ghari, S M; Ghaheri, M; Fallah, F; Ghorbani, T; Beheshti Ale Agha, A; Kazemi, E; Ansarypour, Z

2017-08-15

Stevia rebaudiana is one of the most important biologically sourced and low-calorie sweeteners Bertoni that has a lot of steviol glycosides. Tissue culture is the best for propagation of stevia and micro nutrients can affect both morphological traits and steviol glycosides production. Therefore, the effect of different concentrations of KH2PO4on stevia growth factors and gene expression had been studied by tissue culture methods, RT-PCR and HPLC. According the results, bud numbers had increased significantly in MS + 0.034 mMKH2PO4 media and the highest measured length was seen in plants grown under MS + 0.034 mM KH2PO4 treatment. Also, the highest growth rate (1.396 mm/d) was observed in MS + 0.034 mMKH2PO4.The best concentration of KH2PO4 for expression of UGT74G1 was 0.00425mMand the best one for UGT76G1 expression was 0.017mM. Interestingly, the best media for both stevioside and rebaudioside A accumulation was 0.017mM KH2PO4containing media. There was positive correlation between the best media for gene expression and the best one for steviol glycosides production.

Discontinuous precipitation in a nickel-free high nitrogen austenitic stainless steel on solution nitriding

NASA Astrophysics Data System (ADS)

Mohammadzadeh, Roghayeh; Akbari, Alireza; Grumsen, Flemming B.; Somers, Marcel A. J.

2017-10-01

Chromium-rich nitride precipitates in production of nickel-free austenitic stainless steel plates via pressurised solution nitriding of Fe-22.7Cr-2.4Mo ferritic stainless steel at 1473 K (1200 °C) under a nitrogen gas atmosphere was investigated. The microstructure, chemical and phase composition, morphology and crystallographic orientation between the resulted austenite and precipitates were investigated using optical microscopy, X-ray Diffraction (XRD), Scanning and Transmission Electron Microscopy (TEM) and Electron Back Scatter Diffraction (EBSD). On prolonged nitriding, Chromium-rich nitride precipitates were formed firstly close to the surface and later throughout the sample with austenitic structure. Chromium-rich nitride precipitates with a rod or strip-like morphology was developed by a discontinuous cellular precipitation mechanism. STEM-EDS analysis demonstrated partitioning of metallic elements between austenite and nitrides, with chromium contents of about 80 wt.% in the precipitates. XRD analysis indicated that the Chromium-rich nitride precipitates are hexagonal (Cr, Mo)2N. Based on the TEM studies, (Cr, Mo)2N precipitates presented a (1 1 1)γ//(0 0 2)(Cr, Mo)2N, ?γ//?(Cr, Mo)2N orientation relationship with respect to the austenite matrix. EBSD studies revealed that the austenite in the regions that have transformed into austenite and (Cr, Mo)2N have no orientation relation to the untransformed austenite.

Analysis of features of stainless steels in dissimilar welded joints in chloride inducted corrosion

NASA Astrophysics Data System (ADS)

Topolska, S.; Łabanowski, J.

2017-08-01

Stainless steels of femtic-austenitic microstructure that means the duplex Cr-Ni-Mo steels, in comparison with austenitic steel includes less expensive nickel and has much better mechanical properties with good formability and corrosion resistance, even in environments containing chloride ions. Similar share of high chromium ferrite and austenite, which is characterized by high ductility, determines that the duplex steels have good crack resistance at temperatures up to approximately -40°C. The steels containing approximately 22% Cr, 5% Ni, 3% Mo and 0.2% N crystallizes as a solid solution δ, partially transforming from the temperature of about 1200°C to 850°C into the phase α. The stable structure of considered steels, at temperatures above 850°C, is ferrite, and at lower temperatures the mixture of phase γ+α +σ. The two-phase structure α+γ the duplex steel obtains after hyperquenching at the temperature of stability of the mixture of α+γ phases, and the share of the phases depends on the hyper quenching attributes. Hyperquenching in water, with a temperature close to 1200°C, ensures the instance in the microstructure of the steel a large share of ferrite and a small share of the high chromium austenite. This causes the increase of strength properties and reducing the plasticity of the steel and its resistance ability to cracking and corrosion. Slower cooling from the mentioned temperature, for example in the air, enables the partial transformation of the a phase into the γ one (α → γ) and increasing the share of austenite in the steel structure. It leads to improvement of plasticity properties. In the paper are presented the results of investigations of heteronymous welded joints of duplex steel and austenitic one. The results include the relation between the chemical composition of steels and their weldability.

Mantle water contents beneath the Rio Grande Rift (NM, USA): FTIR analysis of Rio Puerco and Kilbourne Hole peridotite xenoliths

NASA Astrophysics Data System (ADS)

Schaffer, L. A.; Peslier, A. H.; Brandon, A. D.; Selverstone, J.

2015-12-01

Peridotite xenoliths from the Rio Grande Rift (RGR) are being analyzed for H2O contents by FTIR as well as for major and trace element compositions. Nine samples are from the Rio Puerco Volcanic Field (RP) which overlaps the central RGR and southeastern Colorado Plateau; seventeen samples are from Kilbourne Hole (KH) in the southern RGR. Spinel Cr# (Cr/(Cr+Al) = 0.08-0.46) and olivine Mg# (Mg/(Mg+Fe) = 0.883-0.911) of samples fall within the olivine-spinel mantle array from [1], an indicator that these are residues of partial melting. Pyroxene H2O contents in KH correlate with bulk rock and pyroxene Al2O3 contents. The KH clinopyroxene rare earth element (REE) variations fit models of 0-13% fractional melting of a primitive upper mantle. Most KH peridotites have bulk-rock light REE depleted patterns, but five are enriched in light REEs consistent with metasomatism. Variation in H2O content seems unrelated to REE enrichment. Metasomatism is seen in RP pyroxenite xenoliths [2] and will be examined in the peridotites studied here. Olivine H2O contents are low (≤20 ppm), and decrease from core to rim within grains. This is likely due to H loss during xenolith transport by the host magma [3]. Diffusion models of H suggest that mantle H2O contents are still preserved in cores of KH olivine, but not those of RP olivine. The average H2O content of Colorado Plateau clinopyroxene (670 ppm) [4] is ~300 ppm higher than RGR clinopyroxene (350 ppm). This upholds the hypothesis that hydration-induced lithospheric melting occurred during flat-slab subduction of the Farallon plate [5]. Numerical models indicate hydration via slab fluids is possible beneath the plateau, ~600 km from the paleo-trench, but less likely ~850 km away beneath the rift [6]. [1]Arai, 1994 CG 113, 191-204.[2]Porreca et al., 2006 Geosp 2, 333-351.[3]Peslier and Luhr, 2006 EPSL 242, 302-319.[4]Li et al., 2008 JGR 113, 1978-2012.[5]Humphreys et al., 2003 Int Geol Rev 45, 575-595.[6]English et al., 2003 EPSL 214, 619-632.

Effect of natural betaine on estimates of semen quality in mature AI boars during summer heat stress.

PubMed

Cabezón, F A; Stewart, K R; Schinckel, A P; Barnes, W; Boyd, R D; Wilcock, P; Woodliff, J

2016-07-01

This study evaluated the effect of supplemental dietary betaine at three concentrations (0.0%, 0.63% and 1.26%) on semen characteristics, quality and quality after storage on boars. The trial was conducted between 22 July and 1 October 2014 in a boar stud located in Oklahoma. Boars were blocked by age within genetic line and randomly allotted to receive 0% (CON, n (line T)=22, n (line L)=10), 0.63% (BET-0.63%, n (line T)=21, n (line L)=6) or 1.26% (BET-1.26%, n (line T)=23, n (line L)=7). The diets containing betaine were fed over 10 weeks, to ensure supplemental betaine product (96% betaine) daily intakes of 16.34 and 32.68g, for the BET-0.63% and BET-1.26% diets, respectively. Serum homocysteine concentrations were less for animals with betaine treatments (P=0.016). Rectal temperatures of the boars were unaffected by betaine diets. Betaine tended to increase total sperm in the ejaculates when collectively compared with data of the control animals (P=0.093). Sperm morphology analysis indicated there was a greater percent of sperm with distal midpiece reflex (P=0.009) and tail (P=0.035) abnormalities in boars fed the BET-1.26% than boars fed the BET-0.63% diet. Betaine concentration in the seminal plasma was greater in boars with betaine treatments, with animals being fed the 0.63% and 1.26% diets having 59.2% and 54.5% greater betaine concentrations in seminal plasma as compared with boars of the control group (P=0.046). In conclusion, betaine supplementation at 0.63% and 1.26% tended to increase sperm concentration in the ejaculates by 6% and 13%, respectively, with no negative impacts on semen quality when 0.63% of betaine was included in the diet. Copyright © 2016 Elsevier B.V. All rights reserved.

76 FR 25670 - Stainless Steel Sheet and Strip in Coils From Italy: Final Results of the Full Five-Year (“Sunset...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-05

... weight, phosphorus of 0.025 percent or less, silicon of between 0.20 and 0.50 percent, and sulfur of 0... 19 and 22 percent, aluminum of no less than 5.0 percent, phosphorus of no more than 0.045 percent..., manganese, silicon and molybdenum each comprise, by weight, 0.05 percent or less, with phosphorus and sulfur...

Worldwide Esophageal Cancer Collaboration: clinical staging data.

PubMed

Rice, T W; Apperson-Hansen, C; DiPaola, L M; Semple, M E; Lerut, T E M R; Orringer, M B; Chen, L-Q; Hofstetter, W L; Smithers, B M; Rusch, V W; Wijnhoven, B P L; Chen, K N; Davies, A R; D'Journo, X B; Kesler, K A; Luketich, J D; Ferguson, M K; Räsänen, J V; van Hillegersberg, R; Fang, W; Durand, L; Allum, W H; Cecconello, I; Cerfolio, R J; Pera, M; Griffin, S M; Burger, R; Liu, J-F; Allen, M S; Law, S; Watson, T J; Darling, G E; Scott, W J; Duranceau, A; Denlinger, C E; Schipper, P H; Ishwaran, H; Blackstone, E H

2016-10-01

To address uncertainty of whether clinical stage groupings (cTNM) for esophageal cancer share prognostic implications with pathologic groupings after esophagectomy alone (pTNM), we report data-simple descriptions of patient characteristics, cancer categories, and non-risk-adjusted survival-for clinically staged patients from the Worldwide Esophageal Cancer Collaboration (WECC). Thirty-three institutions from six continents submitted data using variables with standard definitions: demographics, comorbidities, clinical cancer categories, and all-cause mortality from first management decision. Of 22,123 clinically staged patients, 8,156 had squamous cell carcinoma, 13,814 adenocarcinoma, 116 adenosquamous carcinoma, and 37 undifferentiated carcinoma. Patients were older (62 years) men (80%) with normal body mass index (18.5-25 mg/kg 2 , 47%), little weight loss (2.4 ± 7.8 kg), 0-1 ECOG performance status (67%), and history of smoking (67%). Cancers were cT1 (12%), cT2 (22%), cT3 (56%), cN0 (44%), cM0 (95%), and cG2-G3 (89%); most involved the distal esophagus (73%). Non-risk-adjusted survival for squamous cell carcinoma was not distinctive for early cT or cN; for adenocarcinoma, it was distinctive for early versus advanced cT and for cN0 versus cN+. Patients with early cancers had worse survival and those with advanced cancers better survival than expected from equivalent pathologic categories based on prior WECC pathologic data. Thus, clinical and pathologic categories do not share prognostic implications. This makes clinically based treatment decisions difficult and pre-treatment prognostication inaccurate. These data will be the basis for the 8th edition cancer staging manuals following risk adjustment for patient characteristics, cancer categories, and treatment characteristics and should direct 9th edition data collection. © 2016 International Society for Diseases of the Esophagus.

Effect of isothermal heat treatment on microstructure and mechanical properties of Reduced Activation Ferritic Martensitic steel

NASA Astrophysics Data System (ADS)

Chandravathi, K. S.; Sasmal, C. S.; Laha, K.; Parameswaran, P.; Nandagopal, M.; Vijayanand, V. D.; Mathew, M. D.; Jayakumar, T.; Rajendra Kumar, E.

2013-04-01

Hardness, tensile properties and microstructural changes in 9Cr-1W-0.06Ta-0.22V-0.08C Reduced Activation Ferritic-Martensitic steel have been investigated after subjecting the steel with isothermal heat treatments for 5 min at temperatures in the range 973-1473 K (below Ac1 to above Ac3 transformation temperatures) followed by oil quenching and tempering at 1033 K for 1 h. These studies have been carried out in an effort to assess the strength of the steel at different microstructural conditions. Optical, scanning and transmission electron microscopic investigations have been carried out to assess the microstructural changes of the steel upon various heat treatments. The steel developed predominantly tempered martensitic structure after the heat treatments. The hardness, tensile strength and the prior austenitic grain size of the steel exhibited minimum values for soaking heat treatment in the intercritical temperature range (i.e.) between Ac1 and Ac3; whereas the ductility was maximum. With increase in isothermal heat treatment temperature above Ac3, hardness, tensile strength and grain size of the steel were found to increase with consequent decrease in tensile ductility. TEM investigations revealed that the coarsening of subgrain and precipitates at grain and sub-grain boundaries on heat treatment of the steel in the inter-critical temperature range. The tensile properties of the steel have been correlated with microstructure.

Two pathways for electrocatalytic oxidation of hydrogen by a nickel bis(diphosphine) complex with pendant amines in the second coordination sphere.

PubMed

Yang, Jenny Y; Smith, Stuart E; Liu, Tianbiao; Dougherty, William G; Hoffert, Wesley A; Kassel, W Scott; Rakowski DuBois, M; DuBois, Daniel L; Bullock, R Morris

2013-07-03

A nickel bis(diphosphine) complex containing pendant amines in the second coordination sphere, [Ni(P(Cy)2N(t-Bu)2)2](BF4)2 (P(Cy)2N(t-Bu)2 = 1,5-di(tert-butyl)-3,7-dicyclohexyl-1,5-diaza-3,7-diphosphacyclooctane), is an electrocatalyst for hydrogen oxidation. The addition of hydrogen to the Ni(II) complex gives three isomers of the doubly protonated Ni(0) complex [Ni(P(Cy)2N(t-Bu)2H)2](BF4)2. Using the pKa values and Ni(II/I) and Ni(I/0) redox potentials in a thermochemical cycle, the free energy of hydrogen addition to [Ni(P(Cy)2N(t-Bu)2)2](2+) was determined to be -7.9 kcal mol(-1). The catalytic rate observed in dry acetonitrile for the oxidation of H2 depends on base size, with larger bases (NEt3, t-BuNH2) resulting in much slower catalysis than n-BuNH2. The addition of water accelerates the rate of catalysis by facilitating deprotonation of the hydrogen addition product before oxidation, especially for the larger bases NEt3 and t-BuNH2. This catalytic pathway, where deprotonation occurs prior to oxidation, leads to an overpotential that is 0.38 V lower compared to the pathway where oxidation precedes proton movement. Under the optimal conditions of 1.0 atm H2 using n-BuNH2 as a base and with added water, a turnover frequency of 58 s(-1) is observed at 23 °C.

Re-evaluation of Ipsilateral Radiation for T1-T2N0-N2b Tonsil Carcinoma at the Princess Margaret Hospital in the Human Papillomavirus Era, 25 Years Later

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Shao Hui, E-mail: shaohui.huang@rmp.uhn.on.ca; Waldron, John; Department of Otolaryngology—Head & Neck Surgery, The Princess Margaret Cancer Centre, University of Toronto, Toronto, Ontario

Purpose: To report the outcome of ipsilateral radiation therapy (RT) in human papillomavirus (HPV)-positive (HPV+) patients and HPV-negative (HPV−) patients with T1-T2N0-N2b tonsillar cancer treated 25 years after our initial historical cohort. Methods and Materials: Patients with T1-T2N0-N2b tonsillar cancer who received ipsilateral RT or bilateral RT between 1999 and 2014 were reviewed. Overall survival (OS), local control (LC), regional control (RC), and grade 3 to 4 late toxicity (LT) were compared between ipsilateral RT and bilateral RT within HPV+ and HPV− patients, separately. Results: HPV status was ascertained in 379/427 (88%) consecutive patients (ipsilateral RT: 62 HPV+, 34 HPV−; bilateralmore » RT: 240 HPV+ 240, 41 HPV−). The proportion of ipsilateral RT by N category for HPV+ and HPV− patients were as follows: N0: 24/37 (65%) versus 28/48 (74%); N1: 21/49 (43%) versus 4/9 (44%); N2a: 10/39 (26%) versus 1/4 (25%); and N2b: 7/177 (4%) versus 1/24 (4%), respectively. Of the patients receiving ipsilateral RT, 94/96 (98%) were treated with RT alone. The median follow-up time was 5.03 years. The respective 5-year rates of OS, LC, RC, and LT were similar between ipsilateral RT and bilateral RT for the HPV+ patients (OS: 89% vs 87%, P=.55; LC: 97% vs 98%, P=.65; RC: 98% vs 97%, P=.27; LT: 17% vs 12%, P=.83) and HPV− patients (OS: 63% vs 48%, P=.27; LC: 90% vs 80%, P=.19; RC: 94% vs 83%, P=.14; LT: 15% vs 22%, P=.36). Of the 96 patients receiving ipsilateral RT, contralateral neck failure (CNF) occurred in 1/52 HPV+ patients and 1/34 HPV− patients. The 5-year CNF rates were 2% (95% CI: 1-9) (HPV+: 2% [0-14]; HPV−: 3% [0-21], P=.66). Five local failures (2 HPV+; 3 HPV−) and no distant failures were seen. The 5-year rates of LC, RC, and LT were 97% versus 90% (P=.24), 98% versus 94% (P=.25), and 18% versus 15% (P=.75) for the HPV+ and HPV− cohorts, respectively. Osteoradionecrosis occurred in 9 patients: 6/47 (13%) treated with conventional RT and 3/49 (6%) with intensity modulated RT (P=.32). Conclusion: Ipsilateral radiation to selected patients with T1-T2N0-N2b tonsillar cancer results in equally excellent outcomes regardless of tumor HPV status.« less

Friction and wear performance of ion-beam deposited diamondlike carbon films on steel substrates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Erdemir, A.; Nichols, F.A.; Pan, X.Z.

1993-01-01

In this study, we investigated the friction and wear performance of ion-beam-deposited diamondlike-carbon (DLC) films (1.5 {mu}m thick) on AISI 440C steel substrates. Furthermore, we ran a series of long-duration wear tests under 5, 10, and 20 N load to assess the load-bearing capacity and durability limits of these films under each load. Tests were performed on a ball-on-disk machine in open air at room temperature {approx} 22{plus_minus}1{degrees}C, and humidity, {approx} 30{plus_minus}5%. For the test conditions explored, we found that (1) the steady-state friction coefficients of pairs without a DLC film were in the range of 0.7 to 0.9 andmore » the average wear rates of 440C balls (9.55 mm diameter) sliding against uncoated 440C disks were on the order of 10{sup {minus}5} mm{sup 3}/N.m, depending on contact load; (2) DLC films reduced the steady-state friction coefficients of test pairs by factors of 6 to 8, and the wear rates of pins by factors of 500 to 2000; (3) The wear of disks coated with a DLC film was virtually unmeasurable while the wear of uncoated disks was quite substantial, (4) these DLC films were able to endure the range of loads, 5 to 20 N, without any delamination and to last over a million cycles before wearing out. During long-duration wear tests, the friction coefficients were initially on the order of 0.15, but decreased to some low values of 0.05 to 0.07 after sliding for 15 to 25 km, depending on the load, and remained low until wearing out. This low-friction regime was correlated with the formation of a carbon-rich transfer film on the wear scar of 440C balls. Micro-laser-Raman spectroscopy and scanning-electron microscopy were used to examine the structure and chemistry of worn surfaces and to elucidate the wear- and friction-reducing mechanisms of the DLC film.« less

Friction and wear performance of ion-beam deposited diamondlike carbon films on steel substrates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Erdemir, A.; Nichols, F.A.; Pan, X.Z.

1993-01-01

In this study, we investigated the friction and wear performance of ion-beam-deposited diamondlike-carbon (DLC) films (1.5 [mu]m thick) on AISI 440C steel substrates. Furthermore, we ran a series of long-duration wear tests under 5, 10, and 20 N load to assess the load-bearing capacity and durability limits of these films under each load. Tests were performed on a ball-on-disk machine in open air at room temperature [approx] 22[plus minus]1[degrees]C, and humidity, [approx] 30[plus minus]5%. For the test conditions explored, we found that (1) the steady-state friction coefficients of pairs without a DLC film were in the range of 0.7 tomore » 0.9 and the average wear rates of 440C balls (9.55 mm diameter) sliding against uncoated 440C disks were on the order of 10[sup [minus]5] mm[sup 3]/N.m, depending on contact load; (2) DLC films reduced the steady-state friction coefficients of test pairs by factors of 6 to 8, and the wear rates of pins by factors of 500 to 2000; (3) The wear of disks coated with a DLC film was virtually unmeasurable while the wear of uncoated disks was quite substantial, (4) these DLC films were able to endure the range of loads, 5 to 20 N, without any delamination and to last over a million cycles before wearing out. During long-duration wear tests, the friction coefficients were initially on the order of 0.15, but decreased to some low values of 0.05 to 0.07 after sliding for 15 to 25 km, depending on the load, and remained low until wearing out. This low-friction regime was correlated with the formation of a carbon-rich transfer film on the wear scar of 440C balls. Micro-laser-Raman spectroscopy and scanning-electron microscopy were used to examine the structure and chemistry of worn surfaces and to elucidate the wear- and friction-reducing mechanisms of the DLC film.« less

Cosmic temperature fluctuations from two years of COBE differential microwave radiometers observations

NASA Technical Reports Server (NTRS)

Bennett, C. L.; Kogut, A.; Hinshaw, G.; Banday, A. J.; Wright, E. L.; Gorski, K. M.; Wilkinson, D. T.; Weiss, R.; Smoot, G. F.; Meyer, S. S.

1994-01-01

The first two years of Cosmic Background Explorer (COBE) Differential Microwave Radiometers (DMR) observations of the cosmic microwave background (CMB) anisotropy are analyzed and compared with our previously published first year results. The results are consistent, but the addition of the second year of data increases the precision and accuracy detected CMB temperature fluctuations. The 2 yr 53 GHz data are characterized by rms temperature fluctuations of (delta-T)(sub rms) (7 deg) = 44 +/- 7 micro-K and (delta-T)(sub rms) (10 deg) = 30.5 +/- 2.7 micro-K at 7 deg and 10 deg angular resolution, respectively. The 53 x 90 GHz cross-correlation amplitude at zero lag is C(0)(sup 1/2) = 36 +/- 5 micro-K (68% CL) for the unsmoothed (7 deg resolution) DMR data. We perform a likelihood analysis of the cross-correlation function, with Monte Carlo simulations to infer biases of the method, for a power-law model of initial density fluctuations, P(k) proportional to R(exp n). The Monte Carlo simulations indicate that derived estimates of n are biased by +0.11 +/- 0.01, while the subset of simulations with a low quadrupole (as observed) indicate a bias of +0.31+/- 0.04. Derived values for 68% confidence intervals are given corrected (and not corrected) for our estimated biases. Including the quadrupole anisotropy, the most likely quadrupole-normalized amplitude is Q(sub rms-PS) = 14.3(sup + 5.2 sub -3.3) micro-K (12.8(sup + 5.2 sub -3.3) micro-K0 with a spectral index n = 1.42(sup + 0.49 sub -0.55)(n = 1.53(sup + 0.49 sub -0.55). With n fixed to 1.0 the most likely amplitude is 18.2 +/- 11.5 micro-K (17.4 +/- 1.5 micro-K). The marginal likelihood of n is 1.42 +/- 0.37 (1.53 +/- 0.37). Excluding the quadrupole anisotropy, the most likely quadrupole-normalized amplitude is Q(sub rms-PS) = 17.4(sup + 7.5 sub -5.2) micro-K (15.8(sup + 7.5 sub -5.2) micro-K) with a spectral index n = 1.11(sup + 0.60 sub -0.55) (n = 1.22(sup + 0.60 sub -0.55). With n fixed to 1.0 the most likely amplitude is 18.6 +/- 1.6 micro-K (18.2 +/- 1.6 micro-K). The marginal likelihood of n is 1.11 +/- 0.40 (1.22 +/- 0.40). Our best estimate of the dipole from the 2 yr DMR data is 3.363 +/- 0.024 mK toward Galactic coordinates (l, b) = (264.4 deg +/- 0.2 deg, 48.1 deg +/- 0.4 deg), and our best estimate of the rms quadrupole amplitude in our sky is 6 +/- 3 micro-K (68% CL).

An Acoustic-Instrumented Mine for Studying Subsequent Burial

DTIC Science & Technology

2007-01-01

seawater . A strong reflection from the transducer face therefore indicates sediment flush with the mine surface (i.e., the mine surface is buried...variations in seawater sound speed and urethane sound speed that create a slight acoustic impedance mismatch at the water-urethane in- terface. The water...following was used: w. = \\//,„/2f/« TTH, U, T;Sinh( kh ) /„• = 0.237 0.52 /„, is the wave friction factor, Uw is the wave orbital velocity

Nutrient loading enhances methane flux in an ombrotrophic bog

NASA Astrophysics Data System (ADS)

Bubier, Jill L.; Juutinen, Sari; Moore, Tim; Arnkil, Sini; Humphreys, Elyn; Marincak, Brenden; Roy, Cameron; Larmola, Tuula

2017-04-01

Peatlands are significant sources of atmospheric methane (CH4) and emission rates may be affected by atmospheric nutrient inputs and associated changes in vegetation. In a long-term (10-15 yr) fertilization experiment at a nutrient-poor, Sphagnum moss- and dwarf shrub-dominated bog in eastern Canada, we tested the effect of ammonium nitrate (NH4NO3,0 to 6.4 g N m-2 yr-1) and potassium phosphate (KH2PO4,5 g P m-2 yr-1) on fluxes of CH4. Fluxes were measured using a closed chamber technique over the growing seasons of 2005 and 2015. The effect of long-term field treatments on aerobic consumption and anaerobic production potentials of CH4 was tested by laboratory incubations of peat samples, as well as an amendment with KH2PO4on anaerobic production potentials at the water table. Over the 10-15 yr, three levels of N plus PK addition and N-only addition of 6.4g N m-2yr-1 decreased the abundance of Sphagnum and Polytrichum mosses, increased the growth and coverage of dwarf shrubs, and caused a decline in surface elevation and thus a higher water table. Overall, CH4 flux was small, ˜ 12 mg m-2 d-1 in the control plots, primarily because of the low water table (30 to 50 cm beneath the peat surface), but flux varied as a function of water table position and treatment. KH2PO4 addition was associated with the highest fluxes: in the 5th treatment year, the PK treatment had the largest CH4 flux (˜25 mg m-2 d-1), whereas in the 15th year the 6.4NPK treatment had the largest flux (˜50 mg m-2 d-1). Rates of potential production and consumption of CH4in laboratory incubations of peat samples were associated with position relative to the water table. Anaerobic potential CH4production was largest in the PK treatment and overall was marginally increased by PK amendment; there were no clear effects of NH4NO3 on CH4 production. The major increase in CH4 flux appearing in the long term seemed to be result of the change in water table position owing to peat subsidence and loss of moss, plus potential stimulation of CH4 production by PK.

Production of 6-pentyl-α-pyrone by trichoderma harzianum in solid-state fermentation

PubMed Central

de Souza Ramos, Aline; Fiaux, Sorele Batista; Leite, Selma Gomes Ferreira

2008-01-01

Many Trichoderma species are able to produce 6-pentyl-α-pyrone (6-PP), a lactone with coconut-like aroma. In the present work, several culture parameters were studied to enhance the production of 6-PP by Trichoderma harzianum 4040 in solid-state fermentation. Green coir powder added to a nutrient solution was used as support material for fermentation. A Plackett-Burman screening technique was applied, followed by a fractionary factorial design. The best culture conditions within the experimental domain studied were (100 g support)−1: sucrose, 3 g; NaNO3, 0.24 g; (NH4)2SO4, 0.18 g; KH2PO4, 0.1 g; inoculum concentration, 2.2 × 106 spores; moisture level, 55%. The temperature established was 28°C. The fermentation under the selected conditions led to a 6-PP production six times higher (5.0 mg/g dry matter) than the initial one (0.8 mg/g dry matter) after seven days of cultivation. PMID:24031295

Production of 6-pentyl-α-pyrone by trichoderma harzianum in solid-state fermentation.

PubMed

de Souza Ramos, Aline; Fiaux, Sorele Batista; Leite, Selma Gomes Ferreira

2008-10-01

Many Trichoderma species are able to produce 6-pentyl-α-pyrone (6-PP), a lactone with coconut-like aroma. In the present work, several culture parameters were studied to enhance the production of 6-PP by Trichoderma harzianum 4040 in solid-state fermentation. Green coir powder added to a nutrient solution was used as support material for fermentation. A Plackett-Burman screening technique was applied, followed by a fractionary factorial design. The best culture conditions within the experimental domain studied were (100 g support)(-1): sucrose, 3 g; NaNO3, 0.24 g; (NH4)2SO4, 0.18 g; KH2PO4, 0.1 g; inoculum concentration, 2.2 × 10(6) spores; moisture level, 55%. The temperature established was 28°C. The fermentation under the selected conditions led to a 6-PP production six times higher (5.0 mg/g dry matter) than the initial one (0.8 mg/g dry matter) after seven days of cultivation.

Effect of Long-Term Service on Microstructure and Mechanical Properties of Martensitic 9% Cr Steel

NASA Astrophysics Data System (ADS)

Golański, Grzegorz; Zielińska-Lipiec, Anna; Zieliński, Adam; Sroka, Marek

2017-03-01

The paper presents the results of research on the X10CrMoVNbN9-1 (T91) steel after long-term service. The material for testing was taken from a pipe section of a boiler superheater coil serviced for around 105,000 h at the temperature of 540 °C, at the pressure of 12.5 MPa. A quantitative analysis including the measurement of mean diameter of subgrains and precipitates as well as the density of dislocations of the examined steel was performed by means of TEM. The microscopic tests of T91 steel were complemented with the results of tests on mechanical properties which included also the short creep tests. After service, the investigated steel was characterized by a retained lath microstructure of tempered martensite with fine subgrain and quite large density of dislocations as well as numerous precipitates. In the microstructure, apart from the particles of M23C6 and MX (VX, NbC, V-wings), the precipitates of Laves phase and single particles of Z phase were revealed. It has been shown that the extent of degradation of the T91 steel microstructure was minor, which resulted from its low temperature of service. Performed tests of mechanical properties showed that these properties fulfilled the minimum requirements for this steel in the as-received condition. A favorable influence of fine precipitates of Laves phase on mechanical properties was observed. Moreover, an insignificant influence of single precipitates of Z phase on the creep resistance of the examined steel was stated.

SU-E-T-274: Radiation Therapy with Very High-Energy Electron (VHEE) Beams in the Presence of Metal Implants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jensen, C; Palma, B; Qu, B

2014-06-01

Purpose: To evaluate the effect of metal implants on treatment plans for radiation therapy with very high-energy electron (VHEE) beams. Methods: The DOSXYZnrc/BEAMnrc Monte Carlo (MC) codes were used to simulate 50–150MeV VHEE beam dose deposition and its effects on steel and titanium (Ti) heterogeneities in a water phantom. Heterogeneities of thicknesses ranging from 0.5cm to 2cm were placed at 10cm depth. MC was also used to calculate electron and photon spectra generated by the VHEE beams' interaction with metal heterogeneities. The original VMAT patient dose calculation was planned in Eclipse. Patient dose calculations with MC-generated beamlets were planned usingmore » a Matlab GUI and research version of RayStation. VHEE MC treatment planning was performed on water-only geometry and water with segmented prostheses (steel and Ti) geometries with 100MeV and 150MeV beams. Results: 100MeV PDD 5cm behind steel/Ti heterogeneity was 51% less than in the water-only phantom. For some cases, dose enhancement lateral to the borders of the phantom increased the dose by up to 22% in steel and 18% in Ti heterogeneities. The dose immediately behind steel heterogeneity decreased by an average of 6%, although for 150MeV, the steel heterogeneity created a 23% increase in dose directly behind it. The average dose immediately behind Ti heterogeneities increased 10%. The prostate VHEE plans resulted in mean dose decrease to the bowel (20%), bladder (7%), and the urethra (5%) compared to the 15MV VMAT plan. The average dose to the body with prosthetic implants was 5% higher than to the body without implants. Conclusion: Based on MC simulations, metallic implants introduce dose perturbations to VHEE beams from lateral scatter and backscatter. However, when performing clinical planning on a prostate case, the use of multiple beams and inverse planning still produces VHEE plans that are dosimetrically superior to photon VMAT plans. BW Loo and P Maxim received research support from RaySearch laboratories; B Hardemark and E Hynning are employees of RaySearch.« less

Chanute AFB, Rantoul, Illinois. Revised Uniform Summary of Surfae Weather Observations (RUSSWO). Parts A-F

DTIC Science & Technology

1972-10-27

FROM HOURLY OBSERVATIONS) 148b__ (- td ,4uTs, ,A-g ILL IN ,IS/RANTQIJL 17-70 F F 1)STATION STATION RARE YEARS NORTH C ALL ;lN IT14FR 1200-1400 CLASS...SPEED MEAN (KNTS) 1 • 3 4.*6 7 - 10 11 •16 17 -. 21 22 *27 28 • 33 34.• 40 41 •47 48 •55 ->56 % I WIND DIR. t . SPEED N _ 0 .2 . 0 5 8,4 NrE , td 1.4...PERCENTAGE FREQUENCY OF WIND *DIRECTION AND SPEED (FROM HOURLY OBSERVATIONS) S Ij) CAjhitblf td - i ILLINJUS/pA1T;JL 37-70 _ - L STATION STATION RAMS TZAIS

Borehole characterization of hydraulic properties and groundwater flow in a crystalline fractured aquifer of a headwater mountain watershed, Laramie Range, Wyoming

NASA Astrophysics Data System (ADS)

Ren, Shuangpo; Gragg, Samuel; Zhang, Ye; Carr, Bradley J.; Yao, Guangqing

2018-06-01

Fractured crystalline aquifers of mountain watersheds may host a significant portion of the world's freshwater supply. To effectively utilize water resources in these environments, it is important to understand the hydraulic properties, groundwater storage, and flow processes in crystalline aquifers and field-derived insights are critically needed. Based on borehole hydraulic characterization and monitoring data, this study inferred hydraulic properties and groundwater flow of a crystalline fractured aquifer in Laramie Range, Wyoming. At three open holes completed in a fractured granite aquifer, both slug tests and FLUTe liner profiling were performed to obtain estimates of horizontal hydraulic conductivity (Kh). Televiewer (i.e., optical and acoustic) and flowmeter logs were then jointly interpreted to identify the number of flowing fractures and fracture zones. Based on these data, hydraulic apertures were obtained for each borehole. Average groundwater velocity was then computed using Kh, aperture, and water level monitoring data. Finally, based on all available data, including cores, borehole logs, LIDAR topography, and a seismic P-wave velocity model, a three dimensional geological model of the site was built. In this fractured aquifer, (1) borehole Kh varies over ∼4 orders of magnitude (10-8-10-5 m/s). Kh is consistently higher near the top of the bedrock that is interpreted as the weathering front. Using a cutoff Kh of 10-10 m/s, the hydraulically significant zone extends to ∼40-53 m depth. (2) FLUTe-estimated hydraulic apertures of fractures vary over 1 order of magnitude, and at each borehole, the average hydraulic aperture by FLUTe is very close to that obtained from slug tests. Thus, slug test can be used to provide a reliable estimate of the average fracture hydraulic aperture. (3) Estimated average effective fracture porosity is 4.0 × 10-4, therefore this fractured aquifer can host significant quantity of water. (4) Natural groundwater velocity is estimated to range from 0.4 to 81.0 m/day, implying rapid pathways of fracture flow. (5) The average ambient water table position follows the boundary between saprolite and fractured bedrock. Groundwater flow at the site appears topography driven.

Serrated Flow and Dynamic Strain Aging in Fe-Mn-C TWIP Steel

NASA Astrophysics Data System (ADS)

Lan, Peng; Zhang, Jiaquan

2018-01-01

The tensile behavior, serrated flow, and dynamic strain aging of Fe-(20 to 24)Mn-(0.4 to 0.6)C twinning-induced plasticity (TWIP) steel have been investigated. A mathematical approach to analyze the DSA and PLC band parameters has been developed. For Fe-(20 to 24)Mn-(0.4 to 0.6)C TWIP steel with a theoretical ordering index (TOI) between 0.1 and 0.3, DSA can occur at the very beginning of plastic deformation and provide serrations during work hardening, while for TOI less than 0.1 the occurrence of DSA is delayed and twinning-dominant work hardening remains relatively smooth. The critical strain for the onset of DSA and PLC bands in Fe-Mn-C TWIP steels decreases as C content increases, while the numbers of serrations and bands increase. As Mn content increases, the critical strain for DSA and PLC band varies irregularly, but the numbers of serrations and bands increase. For Fe-(20 to 24)Mn-(0.4 to 0.6)C TWIP steel with grain size of about 10 to 20 μm, the twinning-induced work hardening rate is about 2.5 to 3.0 GPa, while the DSA-dominant hardening rate is about 2.0 GPa on average. With increasing engineering strain from 0.01 to 0.55 at an applied strain rate of 0.001s-1, the cycle time for PLC bands in Fe-Mn-C TWIP steel increases from 6.5 to 162 seconds, while the band velocity decreases from 4.5 to 0.5 mm s-1, and the band strain increases from 0.005 to 0.08. Increasing applied strain rate leads to a linear increase of band velocity despite composition differences. In addition, the influence of the Mn and C content on the tensile properties of Fe-Mn-C TWIP steel has been also studied. As C content increases, the yield strength and tensile strength of Fe-Mn-C TWIP steel increase, but the total elongation variation against C content is dependent on Mn content. As Mn content increases, the yield strength and tensile strength decrease, while the total elongation increases, despite C content. Taking both tensile properties and serrated flow behavior into consideration, Fe-22Mn-0.4C TWIP steel shows excellent mechanical performance with a high product of tensile strength and total elongation and a slightly serrated stress-strain response. To suppress the negative effect of DSA in Fe-Mn-C TWIP steels on the stability of tensile behavior, a TOI lower than 0.1 is strongly suggested.

Phase composition and fine structure of 0.18C-1Cr-3Ni-1Mo-Fe steel after plasma-electrolytic treatment

NASA Astrophysics Data System (ADS)

Popova, Natalya; Bayatanova, Lyayla; Nikonenko, Elena; Skakov, Mazhyn; Kozlov, Eduard

2017-01-01

The paper presents the transmission electron microscopy (TEM) investigation of 0.18C-1Cr-3Mn-1Mo- Fe steel specimens to study phase transitions and modification of fine structure after plasma-electrolytic treatment (carbonitriding at 850°C during 5 min). TEM investigations involve two points: on the specimen surface and at ˜40 µm distance from it. The experiments show that the structure in the original state is a mixture consisting of ferrite and perlite grains. Carbonitriding results in a considerable modification of the quality and quantity of steel structure. Thus, on the surface, α-phase is represented by lamellar martensite, while at ˜40 µm depth - by massive and lamellar martensite tempered at low and high temperatures. Moreover, on the subsurface of the martensite plates' boundaries retained austenite layers are observed, while inside plates the particles of alloyed cementite, carbonitrides of M23(C,N)6, M2C0.61N0.39, M6,2C3,5N0,3, M(C,N)2, Cr12Fe32Mo7Ni7 types, and β-graphite are present. In the specimen at the depth of ˜40 µm, retained austenite layers are observed on the boundaries of martensite laths and plates, while inside plates only the particles of alloyed cementite and M23(C,N)6 carbonitride are formed.

75 FR 5947 - Stainless Steel Sheet and Strip in Coils from Taiwan: Final Results and Rescission in Part of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-05

... also contains, by weight, phosphorus of 0.025 percent or less, silicon of between 0.20 and 0.50 percent..., chromium of between 19 and 22 percent, aluminum of no less than 5.0 percent, phosphorus of no more than 0..., silicon and molybdenum each comprise, by weight, 0.05 percent or less, with phosphorus and sulfur each...

Investigations on the Behavior of HVOF and Cold Sprayed Ni-20Cr Coating on T22 Boiler Steel in Actual Boiler Environment

NASA Astrophysics Data System (ADS)

Bala, Niraj; Singh, Harpreet; Prakash, Satya; Karthikeyan, J.

2012-01-01

High temperature corrosion accompanied by erosion is a severe problem, which may result in premature failure of the boiler tubes. One countermeasure to overcome this problem is the use of thermal spray protective coatings. In the current investigation high velocity oxy-fuel (HVOF) and cold spray processes have been used to deposit commercial Ni-20Cr powder on T22 boiler steel. To evaluate the performance of the coatings in actual conditions the bare as well as the coated steels were subjected to cyclic exposures, in the superheater zone of a coal fired boiler for 15 cycles. The weight change and thickness loss data were used to establish kinetics of the erosion-corrosion. X-ray diffraction, surface and cross-sectional field emission scanning electron microscope/energy dispersive spectroscopy (FE-SEM/EDS) and x-ray mapping techniques were used to analyse the as-sprayed and corroded specimens. The HVOF sprayed coating performed better than its cold sprayed counterpart in actual boiler environment.

Improved austenitic stainless steel for high temperature applications. [Improved stress-rupture properties

DOEpatents

Not Available

This invention describes a composition for an austenitic stainless steel which has been found to exhibit improved high temperature stress rupture properties. The composition of this alloy is about (in wt. %): 12.5 to 14.5 Cr; 14.5 to 16.5 Ni; 1.5 to 2.5 Mo; 1.5 to 2.5 Mn; 0.1 to 0.4 Ti; 0.02 to 0.08 C; 0.5 to 1.0 Si; 0.01 maximum, N; 0.02 to 0.08 P; 0.002 to 0.008 B; 0.004-0.010 S; 0.02-0.05 Nb; .01-.05 V; 0.005-0.02 Ta; 0.02-0.05 Al; 0.01-0.04 Cu; 0.02-0.05 Co; .03 maximum, As; 0.01 maximum, 0; 0.01 maximum, Zr; and with the balance of the alloy being essentially iron. The carbon content of the alloy is adjusted such that wt. % Ti/(wt. % C+wt. % N) is between 4 and 6, and most preferably about 5. In addition the sum of the wt. % P + wt. % B + wt. % S is at least 0.03 wt. %. This alloy is believed to be particularly well suited for use as fast breeder reactor fuel element cladding.

Inhibition of Mild Steel Corrosion in Hydrochloric Acid Solution by New Coumarin.

PubMed

Kadhum, Abdul Amir H; Mohamad, Abu Bakar; Hammed, Leiqaa A; Al-Amiery, Ahmed A; San, Ng Hooi; Musa, Ahmed Y

2014-06-05

A new coumarin derivative, N , N '-((2E,2'E)-2,2'-(1,4-phenylenebis (methanylylidene))bis(hydrazinecarbonothioyl))bis(2-oxo-2H-chromene-3-carboxamide) PMBH, was synthesized and its chemical structure was elucidated and confirmed using spectroscopic techniques (Infrared spectroscopy IR, Proton nuclear magnetic resonance, 1 H-NMR and carbon-13 nuclear magnetic resonance 13 C-NMR). The corrosion inhibition effect of PMBH on mild steel in 1.0 M HCl was investigated using corrosion potential ( E CORR ), potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), and electrochemical frequency modulation (EFM) measurements. The obtained results indicated that PMBH has promising inhibitive effects on the corrosion of mild steel in 1.0 M HCl across all of the conditions examined. Scanning electron microscopy (SEM) was used to investigate the morphology of the mild steel before and after immersion in 1.0 M HCl solution containing 0.5 mM of PMBH. Surface analysis revealed improvement of corrosion resistance in presence of PMBH.

Far-Field Acoustic Data for the Texas ASE, Inc. Hush-House. Supplement.

DTIC Science & Technology

1982-04-01

wJ t* = -W 0 0.0 cu x. C. m 4!T a. 1 1I IA r2 m0 r t S ’ (A WA w. ". .9 wL * . ac ti 40 I m. aL O 0.14 .) . w -4 En 1 4~~~ 0n an ~ .~( LL (AU. a.3W 0...I I I A (P8%48~t N0I f IS I I coI N m M V4 MO N MM M 6N I 1 0 1 0 .* . .. . . I N 1) %0JO e 10kainM rt w tSY (n0 En " I N W M V 0 4tF . I4 Ilg~g w r 1...A m~ommm at a-at t- * * I m* m a 5 1. tS go .W m 0A400. 0* eN d W) I 4 z 5 -?ZX5OGs II*PII. 1 0 5 OR I ’. Of . I of 50 I * V)A9Ct. 1;4 44944a so ~ ~ 1

Occurrence of two-stage hardening in C-Mn steel wire rods containing pearlitic microstructure

NASA Astrophysics Data System (ADS)

Singh, Balbir; Sahoo, Gadadhar; Saxena, Atul

2016-09-01

The 8 and 10 mm diameter wire rods intended for use as concrete reinforcement were produced/ hot rolled from C-Mn steel chemistry containing various elements within the range of C:0.55-0.65, Mn:0.85-1.50, Si:0.05-0.09, S:0.04 max, P:0.04 max and N:0.006 max wt%. Depending upon the C and Mn contents the product attained pearlitic microstructure in the range of 85-93% with balance amount of polygonal ferrite transformed at prior austenite grain boundaries. The pearlitic microstructure in the wire rods helped in achieving yield strength, tensile strength, total elongation and reduction in area values within the range of 422-515 MPa, 790-950 MPa, 22-15% and 45-35%, respectively. On analyzing the tensile results it was revealed that the material experienced hardening in two stages separable by a knee strain value of about 0.05. The occurrence of two stage hardening thus in the steel with hardening coefficients of 0.26 and 0.09 could be demonstrated with the help of derived relationships existed between flow stress and the strain.

Thulium fiber laser-induced vapor bubble dynamics using bare, tapered, ball, hollow steel, and muzzle brake fiber optic tips

NASA Astrophysics Data System (ADS)

Gonzalez, David A.; Hardy, Luke A.; Hutchens, Thomas C.; Irby, Pierce B.; Fried, Nathaniel M.

2018-03-01

This study characterizes laser-induced vapor bubble dynamics for five different distal fiber optic tip configurations, to provide insight into stone retropulsion commonly experienced during laser ablation of kidney stones. A thulium fiber laser with 1908-nm wavelength delivered 34-mJ energy per pulse at 500-μs pulse duration through five different fibers such as 100-μm-core / 170-μm-OD bare fiber tip, 150- to 300-μm-core tapered fiber tip, 100-μm-core / 300-μm-OD ball tip fiber, 100-μm-core / 340-μm-OD hollow steel tip fiber, and 100-μm-core / 560-μm-OD muzzle brake fiber tip. A high-speed camera with 10-μm-spatial and 9.5-μs-temporal resolution was used to image the vapor bubble dynamics. A needle hydrophone measured pressure transients in the forward (0 deg) and side (90 deg) directions while placed at a 6.8 ± 0.4 mm distance from the distal fiber tip. Maximum bubble dimensions (width/length) averaged 0.7/1.5, 1.0/1.6, 0.5/1.1, 0.8/1.9, and 0.7 / 1.5 mm, for bare, tapered, ball, hollow steel, and muzzle brake fiber tips, respectively (n = 5). The hollow steel tip exhibited the most elongated vapor bubble shape, translating into increased forward pressure in this study and consistent with higher stone retropulsion in previous reports. Relative pressures (a.u.) in (forward/side) directions averaged 1.7/1.6, 2.0/2.0, 1.4/1.2, 6.8/1.1, and 0.3/1.2, for each fiber tip (n = 5). For the hollow steel tip, forward pressure was 4 × higher than for the bare fiber. For the muzzle brake fiber tip, forward pressure was 5 × lower than the bare fiber. Bubble dimensions and pressure measurements demonstrated that the muzzle brake fiber tip reduced forward pressure by partially venting vapors through the portholes, which is consistent with the observation of lower stone retropulsion in previous reports.

Coated 4340 Steel

DTIC Science & Technology

2013-08-26

Magazine, 2004, Vol. 60, No. 68, pp. 7-11. 2. A. Wrigley: Aerospace Metals, American Metal Market , of May 1994. 3. L. L. Sherir: in Corrosion 1...Electrochemistry and Engineering, ASTM STP 801, T. W. Crooker and B. N Leis, Eds., American Society for Testing and Materials, 1983, pp. 5-25. 8. B. Fitzsimons

Evaluation of Mobility, Bioavailability and Toxicity of Pb and Cd in Contaminated Soil Using TCLP, BCR and Earthworms

PubMed Central

Kede, Maria Luiza F. M.; Correia, Fabio V.; Conceição, Paulo F.; Salles Junior, Sidney F.; Marques, Marcia; Moreira, Josino C.; Pérez, Daniel V.

2014-01-01

The objective of the present study was to investigate the reduction of mobility, availability and toxicity found in soil contaminated with lead (Pb) and cadmium (Cd) from Santo Amaro Municipality, Bahia, Brazil using two combined methods, commonly tested separately according to the literature: metal mobilization with phosphates and phytoextraction. The strategy applied was the treatment with two sources of phosphates (separately and mixed) followed by phytoremediation with vetiver grass (Vetiveria zizanioides (L.)). The treatments applied (in triplicates) were: T1—potassium dihydrogen phosphate (KH2PO4); T2—reactive natural phosphate fertilizer (NRP) and; T3—a mixture 1:1 of KH2PO4 and NRP. After this step, untreated and treated soils were planted with vetiver grass. The extraction procedures and assays applied to contaminated soil before and after the treatments included metal mobility test (TCLP); sequential extraction with BCR method; toxicity assays with Eisenia andrei. The soil-to-plant transfer factors (TF) for Pb and Cd were estimated in all cases. All treatments with phosphates followed by phytoremediation reduced the mobility and availability of Pb and Cd, being KH2PO4 (T1) plus phytoremediation the most effective one. Soil toxicity however, remained high after all treatments. PMID:25386955

Reliability of MRSI brain temperature mapping at 1.5 and 3 T

PubMed Central

Thrippleton, Michael J; Parikh, Jehill; Harris, Bridget A; Hammer, Steven J; Semple, Scott I K; Andrews, Peter J D; Wardlaw, Joanna M; Marshall, Ian

2014-01-01

MRSI permits the non-invasive mapping of brain temperature in vivo, but information regarding its reliability is lacking. We obtained MRSI data from 31 healthy male volunteers [age range, 22–40 years; mean ± standard deviation (SD), 30.5 ± 5.0 years]. Eleven subjects (age range, 23–40 years; mean ± SD, 30.5 ± 5.2 years) were invited to receive four point-resolved spectroscopy MRSI scans on each of 3 days in both 1.5-T (TR/TE = 1000/144 ms) and 3-T (TR/TE = 1700/144 ms) clinical scanners; a further 20 subjects (age range, 22–40 years; mean ± SD, 30.5 ± 4.9 years) were scanned on a single occasion at 3 T. Data were fitted in the time domain to determine the water–N-acetylaspartate chemical shift difference, from which the temperature was estimated. Temperature data were analysed using a linear mixed effects model to determine variance components and systematic temperature changes during the scanning sessions. To characterise the effects of instrumental drift on apparent MRSI brain temperature, a temperature-controlled phantom was constructed and scanned on multiple occasions. Components of apparent in vivo temperature variability at 1.5 T/3 T caused by inter-subject (0.18/0.17 °C), inter-session (0.18/0.15 °C) and within-session (0.36/0.14 °C) effects, as well as voxel-to-voxel variation (0.59/0.54 °C), were determined. There was a brain cooling effect during in vivo MRSI of 0.10 °C [95% confidence interval (CI): –0.110, –0.094 °C; p < 0.001] and 0.051 °C (95% CI: –0.054, –0.048 °C; p < 0.001) per scan at 1.5 T and 3 T, respectively, whereas phantom measurements revealed minimal drift in apparent MRSI temperature relative to fibre-optic temperature measurements. The mean brain temperature at 3 T was weakly associated with aural (R = 0.55, p = 0.002) and oral (R = 0.62, p < 0.001) measurements of head temperature. In conclusion, the variability associated with MRSI brain temperature mapping was quantified. Repeatability was somewhat higher at 3 T than at 1.5 T, although subtle spatial and temporal variations in apparent temperature were demonstrated at both field strengths. Such data should assist in the efficient design of future clinical studies. © 2013 The Authors. NMR in Biomedicine published by John Wiley & Sons, Ltd. PMID:24273188

The terrestrial reptile fauna of the Abrolhos Archipelago: species list and ecological aspects.

PubMed

Rocha, C F D; Dutra, G F; Vrcibradic, D; Menezes, V A

2002-05-01

We have studied the terrestrial reptile fauna of the Abrolhos Archipelago (a group of five islands located ca. 70 km off the southern coast of the State of Bahia, Brazil) and analyze here some of its ecological aspects such as diet, thermal ecology, activity, and some reproductive parameters. Three lizards comprise the archipelago's terrestrial reptile fauna: Tropidurus torquatus (Tropiduridae), Mabuya agilis (Scincidae), and Hemidactylus mabouia (Gekkonidae). The first two are diurnal and the latter is crepuscular/nocturnal (initiating activity at ca. 17:30). The activity period of T. torquatus extended from 5:30 to 18:30 h. Mean field body temperatures of active T. torquatus, M. agilis, and H. mabouia were, respectively, 34.0 +/- 3.7 degrees C (range 23.8-38.0 degrees C; N = 75), 34.5 +/- 2.2 degrees C (range 30.8-37.0 degrees C; N = 6), and 26.3 +/- 1.1 degrees C (range 24.8-28.0 degrees C; N = 8). The predominant prey items in the diet of T. torquatus were ants, coleopterans, and hemipterans. In the diet of M. agilis, coleopterans were the most frequent prey items. For H. mabouia, the most important dietary items were orthopterans. Clutch size of T. torquatus averaged 4.1 +/- 1.1 (range 2-6; N = 15) and was significantly related to female size (R2 = 0.618; p = 0.001; N = 15). Clutch size for H. mabouia was fixed (two) and mean litter size of the viviparous M. agilis was 3.3 +/- 0.6 (range 3-4; N = 3). Tropidurus torquatus and H. mabouia deposit their eggs under rocks in the study area, with the former burying them but not the latter; in both species, more than one female often oviposit under the same rock.

Cr[(H3N-(CH2)2-PO3)(Cl)(H2O)]: X-ray single-crystal structure and magnetism of a polar organic-inorganic hybrid chromium(II) organophosphonate.

PubMed

Bauer, Elvira M; Bellitto, Carlo; Colapietro, Marcello; Portalone, Gustavo; Righini, Guido

2003-10-06

Cr[(H(3)N-(CH(2))(2)-PO(3))(Cl)(H(2)O)], a rare example of a polar organic-inorganic hybrid material containing Cr(2+), was prepared from CrCl(2), 2-aminoethylphosphonic acid, and urea in water and isolated as light-blue crystals. It crystallizes in the noncentrosymmetric monoclinic space group P2(1), with a = 5.249(1) A, b = 14.133(3) A, c = 5.275(1) A, and beta = 105.55(2) degrees. The inorganic layer of the hybrid network is formed by Cr(II) five-coordinated by three oxygen atoms from the phosphonates and one from the water molecule in a square pyramidal unit, whose apical position is occupied by the Cl(-) ion. Hydrogen bonds are established between the coordinating water molecule and the oxygen atoms of adjacent phosphonate ligands. The inorganic network is interspersed by ethylammonium groups, and the terminal ammonium moiety is linked to the apical Cl(-) ions through hydrogen bonds. Electrostatic interactions as well as hydrogen bonds and the coordinated chlorine atoms ensure the cohesion of the 3D structure. The lattice is polar (lack of inversion center), and this fact determines the magnetic behavior of the compound at low temperatures. The magnetic susceptibility data in the temperature range from 300 to 50 K show Curie-Weiss behavior, with C = 2.716 cm(3) K mol(-1) and the Weiss constant theta = -2.2 K. The corresponding effective magnetic moment of 4.7 mu(B) compares well with the expected value for Cr(2+) in d(4) high-spin configuration. A slight decrease of the chiT product versus T observed at temperatures below 50 K indicates nearest-neighbor antiferromagnetic exchange interactions. On cooling below T = 6 K, the magnetic susceptibility increases sharply up to a maximum at ca. 5 K and then decreases again. Below T = 6 K, hysteresis loops taken at different temperatures show that Cr[(H(3)N-(CH(2))(2)-PO(3))(Cl)(H(2)O)] behaves as a weak ferromagnet with the critical temperature T(N) at 5.5 K. The spin canting is responsible of the long-range magnetic ordering. The values of the coercive field, H(c), and of remnant magnetization, M(r), obtained from the hysteresis loop at T = 4.5 K (the lowest measured temperature) are 30 Oe and 0.08 mu(B), respectively.

High Fragmentation Steel Production Process

DTIC Science & Technology

1981-08-01

Hsv j , —U -I* : -’ 1 . ’ ; - * - 1 "^Sv i ! :.:.; 1 HEBUCTIOK AHU.,, .../y?.;-’" • jttoireAnoi..|..r!.5^«. ::^;;;i:^l^~!’in...on rmrerae aide 11 neceaaary and Identity by block number) HF- 1 Steel Metallurgical Evaluation MMT-Process improvement 20. ABSTRACT ("ContfBu...ao reraram attba tt n*c*aaMey and. IderUlty by block numbat) Two heats of B0F HF- 1 steel were purchased, one from Republic Steel and one from

Causal Neuro-immune Relationships at Patients with Chronic Pyelonephritis and Cholecystitis. Correlations between Parameters EEG, HRV and White Blood Cell Count

PubMed Central

Kul’chyns’kyi, Andriy B; Kyjenko, Valeriy M; Zukow, Walery; Popovych, Igor L

2017-01-01

Abstract We aim to analyze in bounds KJ Tracey’s immunological homunculus conception the relationships between parameters of electroencephalogram (EEG) and heart rate variability (HRV), on the one hand, and the parameters of bhite blood cell count, on the other hand. Methods In basal conditions in 23 men, patients with chronic pyelonephritis and cholecystitis in remission, recorded EEG (“NeuroCom Standard”, KhAI Medica, Ukraine) and HRV (“Cardiolab+VSR”, KhAI Medica, Ukraine). In portion of blood counted up white blood cell count. Results Revealed that canonical correlation between constellation EEG and HRV parameters form with blood level of leukocytes 0.92 (p<10-5), with relative content in white blood cell count stubnuclear neutrophiles 0.93 (p<10-5), segmentonucleary neutrophiles 0.89 (p<10-3), eosinophiles 0.87 (p=0.003), lymphocytes 0.77 (p<10-3) and with monocytes 0.75 (p=0.003). Conclusion Parameters of white blood cell count significantly modulated by electrical activity some structures of central and autonomic nervous systems. PMID:28730179

A Bridging Water Anchors the Tethered 5-(3-Aminopropyl)-2′-deoxyuridine Amine in the DNA Major Groove Proximate to the N+2 C·G Base Pair: Implications for Formation of Interstrand 5′-GNC-3′ Cross-Links by Nitrogen Mustards‡

PubMed Central

Wang, Feng; Li, Feng; Ganguly, Manjori; Marky, Luis A.; Gold, Barry; Egli, Martin; Stone, Michael P.

2009-01-01

Site-specific insertion of 5-(3-aminopropyl)-2′-deoxyuridine (Z3dU) and 7-deaza-dG into the Dickerson-Drew dodecamers 5′-d(C1G2C3G4A5A6T7T8C9Z10C11G12)-3′ · 5′-d(C13G14C15G16A17A18T19T20-C21Z22C23G24)-3′ (named DDDZ10) and 5′-d(C1G2C3G4A5A6T7X8C9Z10C11G12)-3′ · 5′-d(C13G14C15G16A17A18-T19X20C21Z22C23G24)-3′ (named DDD2+Z10)(X = Z3dU; Z = 7-deaza-dG) suggests a mechanism underlying the formation of interstrand N+2 DNA cross-links by nitrogen mustards, e.g., melphalan and mechlorethamine. Analysis of the DDD2+Z10 duplex reveals that the tethered cations at base pairs A5 · X20 and X8 · A17 extend within the major groove in the 3′-direction, toward conserved Mg2+ binding sites located adjacent to N+2 base pairs C3 · Z22 and Z10 · C15. Bridging waters located between the tethered amines and either Z10 or Z22 O6 stabilize the tethered cations and allow interactions with the N + 2 base pairs without DNA bending. Incorporation of 7-deaza-dG into the DDD2+Z10 duplex weakens but does not eliminate electrostatic interactions between tethered amines and Z10 O6 and Z22 O6. The results suggest a mechanism by which tethered N7-dG aziridinium ions, the active species involved in formation of interstrand 5′-GNC-3′ cross-links by nitrogen mustards, modify the electrostatics of the major groove and position the aziridinium ions proximate to the major groove edge of the N+2 C · G base pair, facilitating interstrand cross-linking. PMID:18549246

List of Inspected Tank Barges and Tankships

DTIC Science & Technology

1980-01-01

C) CC’ L-4 I-I. tD w V) 8.L T 4 I-I a 0 7 z 70 70 z7 ab 2! 7.I in -9 00 M T 0 x 0 0 t0 0 t3 M wA (0 a a ty m 0 0 LA UN U 0 C3 U’N C; N; ’ ’ ’ - N C...4 0 4 4C 13&; 51 a 2I x~ -i wt W tD . w3 9 1 0& C) 1 w I U4 ox’. 94. 0: .5 It o 5A (Z it CorI.- .5L LD D w U) N-CLPp0l 0w . 0 a. ts. m5. t49- -1 0...7IL a,& 1 -j & I m 7’ en.I.1 . 4. co 4 m I f r.) ’N a, 𔃺 a, U. U. N4.’ ,sL a .4 r .47 . 󈧭u 1. X- D2 4.. a. t. x 43 N P. tD Il ’DX 03 P X tm. I V , r

In a 21-2n deformed stainless steel influence of recovery temperature

NASA Astrophysics Data System (ADS)

De Ita, A.; Ugalde, P.; Flores, D.

2017-01-01

We present the influence high heat treatment temperature of a nitrogen austenitic stainless steel, deform by cold compression, in 10 different percentages. The steel contains high chromium (19.25 %), nickel (1.5 %) and nitrogen (0.2 %). The typical applications for this alloy are automobile parts and special valves for his excellent mechanical properties and corrosion resistance. Produced by hot rolling, they were subjected homogenized treatment at 975 °C for 45 minutes. Subsequently, deformed, by cold compression. We get ten different deformations, from 3 % to 22 %. These samples then to a heat treatment at 750 °C for one, 2 and 4 hours respectively. To observe the microstructure all samples were metallographic study and measured also their Rockwell C hardness. The initial sample has an austenitic matrix with a small amount of precipitates with a 42 RC average hardness. The homogenized sample had a 39 RC hardness. The deformed samples increased their hardness with a maximum of 49 RC. The samples with the treatment, showed a lower hardness with longer time with high dispersion. The decreased of hardness is due to the elimination of residual stresses and precipitates increasing size.

A biomechanical analysis of sublaminar and subtransverse process fixation using metal wires and polyethylene cables.

PubMed

Fujita, Masaru; Diab, Mohammad; Xu, Zheng; Puttlitz, Christian M

2006-09-01

An in vitro biomechanical calf thoracic spine study. To evaluate the biomechanical stability of sublaminar and subtransverse process fixation using stainless steel wires and ultra-high molecular weight polyethylene (UHMWPE) cables. It is commonly held that transverse process fixation provides less stability than sublaminar fixation. To our knowledge, this is the first biomechanical study to compare the stability afforded by sublaminar fixation and subtransverse process fixation using metal wire and UHMWPE cable before and after cyclic loading. There were 6 fresh-frozen calf thoracic spines (T4-T9) used to determine the sublaminar fixation stiffness and subtransverse process fixation stiffness in each group. Double strands of 18-gauge stainless steel wire, 3 and 5 mm-width UHMWPE cable (Nesplon; Alfresa, Inc., Osaka, Japan) were applied to each spine. Cyclic pure flexion-extension moment loading (2 Nm, 0.5 Hz, 5000 cycles) was applied after the initial stability was analyzed by measuring the range of motion. Statistical analyses were used to delineate differences between the various experimental groups. Subtransverse process wiring was more stable than sublaminar wiring after cyclic loading in flexion-extension (P < 0.05). There were no significant differences between each group in lateral bending and axial rotation after cyclic loading. Sublaminar stainless steel wiring was more stable than sublaminar 3 and 5-mm cable before and after cyclic loading in axial rotation (P < 0.01). Acute subtransverse process fixation using 3-mm cable was less stable after cyclic loading in axial rotation (P < 0.05). All other groups did not produce statistically significant differences. Subtransverse process fixation provides at least as much stability as sublaminar fixation. A 5-mm UHMWPE cable and stainless steel wire result in equivalent sublaminar and subtransverse process stability.

Geographic List of Prime Contract Awards. Oct 91 - Sep 92. FY92. (Nanticoke Maryland - Garden City Michigan)

DTIC Science & Technology

1993-01-01

N4 ._ K MWL0.I- It 0o 00 10 0 0 00-40000 -04 0 (nK 00M0 a >- 22 Z 22222 z zzz z R nowo u 0 cow0 Q 4040040404 0 40404 40 If I001- a 04C 0ɜ 0 0 04 04.4...W40ld 00000I -4-000 C> 0 C000o1.170 1-00 -4 X I ( 1 010-4 1 0):C 0)~ Y- 40oO -4(0(0 oxZZ-j 0000 0-I -f) 347 M. Hf 4 5 00-4 if0)0 04 4000 04V)(󈨋) (7< <) 4...00000000’cJa 40C0,ln)00 Af I M02000 it vlwt"A4 (0 NOWO -t4--4-No )0) )NN0)I)1l00D0-40-I)0 -40D-𔃺C’.I002C-4 of I M0C000 ofiil -f 00 nn)U0f4 ~ aiN)noo~0)t

Proceedings of the OGAMM Meeting (3rd) Held in Keswick-On-Derwentwater, Cumbria, England on September 4-7, 1990

DTIC Science & Technology

1990-09-07

and frequency shifting, (4) Investigation of device processes in optical waveguides and fibers; optical bistability for optical memory operation, and...all relative to urea, unless stated otherwise. Compound SHG Colour (1) 0.60 Yellow (2) 0.70 Dark green (3) 0.01 Pale yellow (4) 0.22 Yellow (5) 0.73...LOUGHBOROUGH T. KING UNIVERSITY OF TECHNOLOGY H. Coles N. PHILIPS I - LASER ENCHANCED 1 - OPTICAL & THERMAL DENSIFICATION PROPERTIES 2 - SOLID STATE

Laser Welding of Coated Press-hardened Steel 22MnB5

NASA Astrophysics Data System (ADS)

Siltanen, Jukka; Minkkinen, Ari; Järn, Sanna

The press-hardening process is widely used for steels that are used in the automotive industry. Using ultra-high-strength steels enables car manufacturers to build lighter, stronger, and safer vehicles at a reduced cost and generating lower CO2 emissions. In the study, laser welding properties of the coated hot stamped steel 22BMn5 were studied. A constant 900 °C temperature was used to heat the steel plates, and two different furnace times were used in the press-hardening, being 300 and 740 seconds. Some of the plates were shot blasted to see the influence of the partly removed oxide layer on the laser welding and quality. The welding set-up, welding, and testing of the weld specimens complied with the automotive testing code SEP 1220.

Expression of fas protein on CD4+T cells irradiated by low level He-Ne

NASA Astrophysics Data System (ADS)

Nie, Fan; Zhu, Jing; Zhang, Hui-Guo

2005-07-01

Objective: To investigate the influence on the Expression of Fas protein on CD4+ T cells irradiated by low level He-Ne laser in the cases of psoriasis. Methods:the expression of CD4+ T Fas protein was determined in the casee of psoriasis(n=5) pre and post-low level laser irradiation(30 min、60min and 120min)by flow cytometry as compared withthe control(n=5). Results:In the cases of psoriasis,the expression of CD4+T FAS protein 21.4+/-3.1% was increased significantly than that of control group 16.8+/-2.1% pre-irradiation, p<0.05in the control,there is no difference between pre and post- irradiation,p>0.05in the cases , the expression of CD4+T Fas protein wae positively corelated to the irradiation times, when the energy density arrived to 22.92J/cm2（60 minutes）and 45.84J/cm2（120minutes）, the expression of CD4+ T Fas protein was increased significantly as compared with pre-irradiation,p<0.05.Conclusion: The expression of CD4+T Fas protein may be increased by low level He-Ne laser irradiation ,the uncontrolled status of apoptosis could be corrected.

Conditions and phase shift of fluid resonance in narrow gaps of bottom mounted caissons

NASA Astrophysics Data System (ADS)

Zhu, Da-tong; Wang, Xing-gang; Liu, Qing-jun

2017-12-01

This paper studies the viscid and inviscid fluid resonance in gaps of bottom mounted caissons on the basis of the plane wave hypothesis and full wave model. The theoretical analysis and the numerical results demonstrate that the condition for the appearance of fluid resonance in narrow gaps is kh=(2 n+1)π ( n=0, 1, 2, 3, …), rather than kh= nπ ( n=0, 1, 2, 3, …); the transmission peaks in viscid fluid are related to the resonance peaks in the gaps. k and h stand for the wave number and the gap length. The combination of the plane wave hypothesis or the full wave model with the local viscosity model can accurately determine the heights and the locations of the resonance peaks. The upper bound for the appearance of fluid resonance in gaps is 2 b/ L<1 (2 b, grating constant; L, wave length) and the lower bound is h/ b≤1. The main reason for the phase shift of the resonance peaks is the inductive factors. The number of resonance peaks in the spectrum curve is dependent on the ratio of the gap length to the grating constant. The heights and the positions of the resonance peaks predicted by the present models agree well with the experimental data.

Evaluation of MR issues for the latest standard brands of orthopedic metal implants: plates and screws.

PubMed

Zou, Yue-Fen; Chu, Bin; Wang, Chuan-Bing; Hu, Zhi-Yi

2015-03-01

The study was performed to evaluate magnetic resonance (MR) issues for the latest standard brands of plates and screws used in orthopedic surgery at a 1.5-T MR system, including the safety and metallic artifacts. The plates and screws (made of titanium alloy and stainless steel materials, according to the latest standard brands) were assessed for displacement in degrees, MRI-related heating and artifacts at a 1.5-T MR system. The displacement in degrees of the plates and screws was evaluated on an angel-measurement instrument at the entrance of the MR scanner. The MRI-related heating was assessed on a swine leg fixed with a plate by using a "worst-case" pulse sequence. A rectangular water phantom was designed to evaluate metallic artifacts of a screw on different sequences (T1/T2-weighted FSE, STIR, T2-FSE fat saturation, GRE, DWI) and then artifacts were evaluated on T2-weighted FSE sequence by modifying the scanning parameters including field of view (FOV), echo train length (ETL) and bandwidth to identify the influence of parameters on metallic artifacts. 15 volunteers with internal vertebral fixation (titanium alloy materials) were scanned with MR using axial and sagittal T2-FSE, sagittal T2-FSE fat suppression and STIR with conventional and optimized parameters, respectively. Then all images were graded by two experienced radiologists having the experience of more than 7 years under double-blind studies that is neither of them knew which was conventional parameter group and optimized parameter group. The average deflection angle of titanium alloy and stainless steel implants were 4.3° and 7.7°, respectively, (less than 45°) which indicated that the magnetically induced force was less than the weight of the object. The deflection angle of the titanium alloy implants was less than the stainless steel one (t=9.69, P<0.001). The average temperature changes of titanium alloy before and after the scan was 0.48°C and stainless steel implants was 0.74°C, respectively, with the background temperature changes of 0.24°C. The water phantom test indicated that the DWI sequence produced largest artifacts, while FSE pulse sequence produced smallest artifacts. And T2-weighted FSE fat saturation sequence produced larger artifacts than STIR sequence. The influence of the scanning parameters on metallic artifacts was verified that metallic artifacts increased with longer echo train length and bigger FOV, while decreased with larger bandwidth. The interreader agreement was good or excellent for each set of images graded with Cohen's Kappa statistic. Image grading of axial and sagittal T2-FSE with optimized parameters were significantly superior to that with conventional parameters (grade, 3.3±0.5 vs 2.7±0.6, P=0.003; 3.2±0.4 vs 1.9±0.7, P=0.001) and image of STIR sequence received a better grade than T2-FSE FS sequence (grade, 3.4±0.5 vs 1.7±0.6, P<0.001). The latest standard plates and screws used in orthopedic surgery do not pose an additional hazard or risk to patients undergoing MR imaging at 1.5-T or less. Though artifacts caused by them cannot be ignored because of their relatively large size, it is possible to be minimized by choosing appropriate pulse sequences and optimizing scanning parameters, such as FSE and STIR sequence with large bandwidth, small FOV and appropriate echo train length. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Chinae, ROK AFS K-10, Korea. Revised Uniform Summary of Surface Weather Observations (RUSSWO). Parts A-F.

DTIC Science & Technology

1968-04-10

5.L 5.6 5.8 2.5 o.’ 9 7 6c NCV .’ 5.4 . 5.4 6.6 4.1 1’.2 8758 CEC 3.7 .5 3.7 5.3 6.6 11.6 9ർ TOTALS .1 9.4 .1 7 1 .0 9.5 11.6 6.2 . 17.2 1,.8565...51-N3,55-61,63-66 NCV STATION STATO NAME YEARS MANTH ALL WEATHER ? C -11. CLASS HOURS I ST I SPEED --0 - MEAN (KNTS) 1 - 3 4 - 6 7-10 11 - 16 17 21 22...61963-66 Ncv STATION STATION SAME YEARS .ONT. ALL WEATFER 12-C-4 ClAs L S C5 T ) SPEED - I MEAN (KNTS) 1 - 3 4 - 6 7 - 10 11 - 16 17 21 22 27 28 - 33

Magnetic structures of R5Ni2In4 and R11Ni4In9 (R  =  Tb and Ho): strong hierarchy in the temperature dependence of the magnetic ordering in the multiple rare-earth sublattices.

PubMed

Ritter, C; Provino, A; Manfrinetti, P; Pecharsky, V K; Gschneidner, K A; Dhar, S K

2015-12-02

The magnetic properties and magnetic structures of the R 5Ni2In4 and the microfibrous R 11Ni4In9 compounds with R  =  Tb and Ho have been examined using magnetization, heat capacity, and neutron diffraction data. Rare earth atoms occupy three and five symmetrically inequivalent rare earth sites in R 5Ni2In4 and R 11Ni4In9 compounds, respectively. As a result of the intra- and inter-magnetic sublattice interactions, the magnetic exchange interactions are different for various rare earth sites; this leads to a cascade of magnetic transitions with a strong hierarchy in the temperature dependence of the magnetic orderings. A transition at T C  =  125 K in Tb5Ni2In4 [κ 1  =  (0, 0, 0)] leads to a ferro/ferrimagnetic order where the magnetic ordering in one of the three R-sublattices leads to the ordering of another one; the third sublattice stays non-magnetic. New magnetic Bragg peaks appearing below T N  =  20 K can be indexed with the incommensurate magnetic propagation vector κ 2  =  (0, 0.636, ½); at T N  =  20 K a cycloidal spin order, which acts mostly upon the third R-sublattice, occurs. Ho5Ni2In4 establishes first antiferromagnetism [κ  =  (0, 0, 0)] at T N  =  31 K on two R-sublattices; then the system becomes ferro/ferrimagnetic at T C  =  25 K with the third sublattice ordering as well. Tb11Ni4In9 has three magnetic transitions at T C  =  135 K, T N1  =  35 K and at T N2  =  20 K; they are respectively coupled to the appearance of different propagation vectors [κ 1  =  (0, 0, 0), κ 2  =  (0, 0, ½), κ 3  =  (0, 1, ½)], which themselves are operating differently on the five different R-sublattices. Two sublattices remain mostly ferromagnetic down to lowest temperature while the three others are predominantly coupled antiferromagnetically. In Ho11Ni4In9 a purely antiferromagnetic order, described by four different magnetic propagation vectors [κ 1  =  (0, 0.62, 0), κ 2  =  (0, 1, 0), κ 3  =  (0, 0, ½), κ 4  =  (0, 1, ½)], succeedingly includes all five different sublattices on cooling through transitions at T N1  =  22 K, T N2  =  12 K, T N3  =  8 K and T N4  =  7 K. The strength of the magnetic interactions of the different sublattices can be linked to structural details for both R 5Ni2In4 and R 11Ni4In9 compounds.

[Induction of free radicals after dietary exposure by mercury contaminated rice and protective effect of coexisting selenium].

PubMed

Ji, Xiu-ling; Cheng, Jin-ping; Wang, Wen-hua; Qu, Li-ya; Zhao, Xiao-xiang; Zhuang, Hui-sheng

2006-10-01

Sprague-Dawley rats were reared by environmental mercury contaminated rice to survey the potential health risk of Wanshan mercury mining area. Electron spin resonance (ESR) was introduced to detect the species and the intensities of free radicals, using spin trap 5,5-dimethyl-1-pyrroline-N-oxide (DMPO). The results showed that the mercury-contaminated rice significantly increased the levels of free radicals and MDA in rat brain at 7 days (p < 0.05). ESR spectrums showed that the principal spin adducts resulted from the trapping of alkyl free radical (alphaH = 22.7 x 10(-4)T +/- 1.6 x 10(-4)T, alphaN = 15.5 x 10(-4)T +/- 0.5 x 10(-4)T), and hydroxyl radical. Levels of free radicals and MDA increased slowly until after 90-day exposure period (83%, 100%). Element correlation analysis showed high correlations of mercury and selenium in the brain of rat fed with Wanshan rice, suggesting that the coexisting selenium in rice exhibited antagonistic effects on both mercury accumulation and toxicity. The slight increases of free radicals in rat brain at 7, 20 and 30-day exposure periods should be related with the scavenger effect of Se.

Williams AFB, Chandler, Arizona. Revised Uniform Summary of Surface Weather Observations (RUSSWO)

DTIC Science & Technology

1975-07-16

I 9 ,3 " T o, , l o,_ _ _ _ 4LOt O Ib ,7T.1.T; * i1 2~ . 3- 7V3,.l . 6 2076 I . 5 .B--- . 0T - 𔃾.01 - - - ’ Wet~~~~26 Boi 206786 101 5;4715 2 C...1 9. 1011.12 13. 14 I. 16 17.18 19.20 21.22 23.24 25".26 27.28129.30 .31 D.B./W.B. pDy nulbFWetI ulbOew Porn , 34/ 33 289 32/3R1 _ I jJ _, _ 267 30...34 Boi ., __ __ __’ _ _ ’ i ’ ... .____... --I-- LU O , B. I t .<- " B _ __,, , Z X1>.I I _.....__ .. ._-via O.. n I I- -V)~~ - - - - -- - - - - - - -A

Cardiovascular magnetic resonance profiling of coronary atherosclerosis: vessel wall remodelling and related myocardial blood flow alterations.

PubMed

Jahnke, Cosima; Manka, Robert; Kozerke, Sebastian; Schnackenburg, Bernhard; Gebker, Rolf; Marx, Nikolaus; Paetsch, Ingo

2014-12-01

To determine the association between coronary vessel wall morphology and haemodynamic consequences to the myocardium using a combined cardiovascular magnetic resonance (CMR) imaging protocol. Non-invasive CMR profiling of coronary atherosclerotic wall changes and related myocardial blood flow impairment has not been established yet. Sixty-three patients (45 men, 61.5 ± 10.7 years) with suspected or known coronary artery disease underwent 3.0 Tesla CMR imaging. The combined CMR protocol consisted of the following imaging modules at rest: 3D vessel wall imaging and flow measurement of the proximal right coronary artery (RCA), myocardial T2*, and first-pass perfusion imaging. During adenosine stress coronary flow, T2* and first-pass perfusion imaging were repeated. Coronary X-ray angiography classified patient groups: (i) all-smooth (n = 19); (ii) luminal irregular (diameter reduction < 30%; n = 35); and (iii) stenosed RCA (diameter reduction ≥ 50%; n = 9). The ratio of CMR-derived vessel wall area-to-lumen area significantly increased stepwise for the comparison of all-smooth vs. luminal irregular vs. stenosed RCA (1.9 ± 0.6 vs. 2.6 ± 0.6 vs. 3.6 ± 0.9, P < 0.01). Epicardial coronary flow reserve exhibited a stepwise significant decrease (3.4 ± 0.5 vs. 2.9 ± 0.7 vs. 1.7 ± 0.3, P < 0.01). On the myocardial level, stress-induced percentage gain of T2* values (ΔT2*) was significantly decreased between groups (29.2 ± 10.6 vs. 9.0 ± 9.8 vs. 2.2 ± 11.8%, P < 0.01) while perfusion reserve index decreased in the presence of stenosed RCA only (2.2 ± 0.6 vs. 2.0 ± 0.4 vs. 1.3 ± 0.3, P = ns and P < 0.01, respectively). The proposed comprehensive CMR imaging protocol provided a non-invasive approach for direct assessment of coronary vessel wall remodelling and resultant pathophysiological consequences on the level of epicardial coronary and myocardial blood flow in patients. Published on behalf of the European Society of Cardiology. All rights reserved. © The Author 2014. For permissions please email: journals.permissions@oup.com.

Single step biotransformation of corn oil phytosterols to boldenone by a newly isolated Pseudomonas aeruginosa.

PubMed

Eisa, Mohamed; El-Refai, Heba; Amin, Magdy

2016-09-01

A new potent Pseudomonas aeruginosa isolate capable for biotransformation of corn oil phytosterol (PS) to 4-androstene-3, 17-dione (AD), testosterone (T) and boldenone (BOL) was identified by phenotypic analysis and 16S rRNA gene sequencing. Sequential statistical strategy was used to optimize the biotransformation process mainly concerning BOL using Factorial design and response surface methodology (RSM). The production of BOL in single step microbial biotransformation from corn oil phytosterols by P. aeruginosa was not previously reported. Results showed that the pH concentration of the medium, (NH 4 ) 2 SO 4 and KH 2 PO 4 were the most significant factors affecting BOL production. By analyzing the statistical model of three-dimensional surface plot, BOL production increased from 36.8% to 42.4% after the first step of optimization, and the overall biotransformation increased to 51.9%. After applying the second step of the sequential statistical strategy BOL production increased to 53.6%, and the overall biotransformation increased to 91.9% using the following optimized medium composition (g/l distilled water) (NH 4 ) 2 SO 4 , 2; KH 2 PO 4 , 4; Na 2 HPO 4 . 1; MgSO 4 ·7H 2 O, 0.3; NaCl, 0.1; CaCl 2 ·2H 2 O, 0.1; FeSO 4 ·7H 2 O, 0.001; ammonium acetate 0.001; Tween 80, 0.05%; corn oil 0.5%; 8-hydroxyquinoline 0.016; pH 8; 200 rpm agitation speed and incubation time 36 h at 30 °C. Validation experiments proved the adequacy and accuracy of model, and the results showed the predicted value agreed well with the experimental values.

The slab thickness of the mid-latitude ionosphere.

NASA Technical Reports Server (NTRS)

Titheridge, J. E.

1973-01-01

The thickness of the peak of the ionosphere depends primarily on the temperature T sub n of the neutral gas, and corresponds approximately to an alpha-Chapman layer at a temperature of 0.87T sub n. The overall slab thickness, as given by Faraday rotation measurements, is then tau = 0.22T sub n + 7 km. Expansion of the topside ionosphere, and changes in the E- and F1-regions increase tau by about 20 km during the day in summer. Near solar minimum, tau is increased by a lowering of the O(+)/H(+) transition height; if the neutral temperature T sub n is estimated, this height can be obtained from observed values of tau. Hourly values of slab thickness were determined over a period of 6 yr at 34 and 42 S. Near solar maximum the nighttime values were about 260 km in all seasons. The corresponding neutral temperatures agree with satellite drag values; they show a semiannual variation of 14% and a seasonal change of 5%. Daytime values of tau were about 230 km in winter and 320 km in summer, implying a seasonal change of 30% in T sub n.

Project of Reforms Proposed for the Don Public Education in the First Half of 1860: A. M. Dondukov-Korsakov, Kh. I. Popov, N. I. Krasnov

ERIC Educational Resources Information Center

Peretyatko, Artyom Yu.; Zulfugarzade, Teymur E.

2017-01-01

The paper reviews the project of reforms in the Don education, which were proposed by prominent public figures in the early 1860s., namely by A. M. Dondukov-Korsakov, Kh. I. Popov and N. I. Krasnov. Based on archival materials and publications by these authors, which in some cases have not been previously used in scientific studies, the paper…

Air Force Global Weather Central System Architecture Study. Final System/Subsystem Summary Report. Volume 5. System Description

DTIC Science & Technology

1976-03-01

ORGANIZATION AIR FORCE SYSTEMS COMMAND LOS ANGELES, CALIFORNIA 90009 339 /* nr ■■■■’ ■■ - -— MkteÄä^HlÜtilÜ • i T-^-’-^w^:—v-T^^-vwr-« -.— ^■.».,𔃾...NUMBER T CONTRACT OR CHANT NUMBER,«) F04701-75-C-0n4 9 PERFORMING ORGANIZATION NAM« AND ADDRESS SYSTEM DEVELOPMENT CORPORATION 2500 Colorado...22 Current AFGWC Organizational Structure 68 23 Operations Staff Organization 70 24 Satellite Data Processing Branch Organization 71 25 Data

Coating-Substrate Systems for Thermomechanically Durable Turbine Airfoils

DTIC Science & Technology

2015-06-30

vapor phase NiA ! aluminide and NiAI(Cr.Zr) coated Rene N5 samples cycled at 1093°C with Ae, = 0.35%. PtAI VPA NiAI(Cr,Zr) EQ Y-Y’ 10000.0... 505 (2001). 2. T.M. Pollock and S. Tin, AIAA J. Propulsion and Power, 22, 2, (2006), pp. 361 - 374. 3. A.G. Evans, D.R. Clarke and C.G. Lev

Validity of Bioelectrical Impedance Analysis for Measuring Changes in Body Water and Percent Fat After Bariatric Surgery

PubMed Central

Widen, Elizabeth M.; Strain, Gladys; King, Wendy C.; Yu, Wenwen; Lin, Susan; Goodpaster, Bret; Thornton, John; Courcoulas, Anita; Pomp, Alfons

2014-01-01

Background Few studies have validated bioelectrical impedance analysis (BIA) following bariatric surgery. Methods We examined agreement of BIA (Tanita 310) measures of total body water (TBW) and percent body fat (%fat) before (T0) and 12 months (T12) after bariatric surgery, and change between T0 and T12 with reference measures: deuterium oxide dilution for TBW and three-compartment model (3C) for %fat in a subset of participants (n=50) of the Longitudinal Assessment of Bariatric Surgery-2. Results T0 to T12 median (IQR) change in deuterium TBW and 3C %fat was −6.4 L (6.4 L) and −14.8 % (13.4 %), respectively. There were no statistically significant differences between deuterium and BIA determined TBW [median (IQR) difference: T0 −0.1 L (7.1 L), p=0.75; T12 0.2 L (5.7 L), p=0.35; Δ 0.35 L(6.3 L), p=1.0]. Compared with 3C, BIA underestimated %fat at T0 and T12 [T0 −3.3 (5.6), p<0.001; T12 −1.7 (5.2), p=0.04] but not change [0.7 (8.2), p=0.38]. Except for %fat change, Bland-Altman plots indicated no proportional bias. However, 95 % limits of agreement were wide (TBW 15–22 L, %fat 19–20 %). Conclusions BIA may be appropriate for evaluating group level response among severely obese adults. However, clinically meaningful differences in the accuracy of BIA between individuals exist. PMID:24464517

Processes affecting the stable isotope composition of calcite during precipitation on the surface of stalagmites: Laboratory experiments investigating the isotope exchange between DIC in the solution layer on top of a speleothem and the CO2 of the cave atmosphere

NASA Astrophysics Data System (ADS)

Dreybrodt, Wolfgang; Hansen, Maximilian; Scholz, Denis

2016-02-01

We present a theoretical derivation of the exchange time, τex, needed to establish isotopic equilibrium between atmospheric CO2 in a cave and HCO3- dissolved in a thin water film covering the surface of a speleothem. The result is τex = τredex · [HCO3-]/ (KH · pCO2cave) , where τredex depends on the depth, a, of the water film and on temperature. [HCO3-] is the concentration of bicarbonate, pCO2cave the partial pressure of CO2, and KH is Henry's constant. To test the theory we prepared stagnant or flowing thin films of a NaHCO3 solution and exposed them at 20 °C to an CO2 containing atmosphere of pCO2 500, 12,500, or 25,000 ppmV and defined isotope composition. The δ13C and δ18O values of the DIC in the solution were measured as a function of the exposure time. For stagnant films with depths between 0.06 and 0.2 cm the δ13C values exhibit an exponential approach towards isotope equilibrium with the atmospheric CO2 with exchange time, τex. The δ18O values first evolve towards isotopic equilibrium with atmospheric CO2, reach a minimum value and then drift away from the isotopic equilibrium with atmospheric CO2 approaching a steady state caused by isotopic exchange of oxygen with water. The experimental findings are in satisfactory agreement with the theoretical predictions. To further investigate isotope evolution in cave analogue conditions, a water film containing 5 mmol/L of NaHCO3 with a depth of 0.013 cm flowing down an inclined borosilicate glass plate was exposed to an atmosphere with pCO2 = 500 ppmV at a temperature of 20 °C. The δ13C and δ18O values were measured as a function of flow (exposure) time, t. The isotope compositions in the DIC of the water film decrease linear in time by δDIC (t) =δDIC (0) - (δDIC (0) -δDIC (∞)) · t /τex where δDIC (0) is the initial isotope composition of dissolved inorganic carbon (DIC) in the water film and δDIC (∞) its final value. From these data an exchange time τex of ca. 7000 s was obtained, in satisfactory agreement with the theoretical predictions. The exchange times can be calculated by τex = τredex · [HCO3-]/ (KH · pCO2cave), where τredex is given by the theory as function of temperature and the depth, a, of the water film. This way it is possible to obtain exchange times for various conditions of stalagmite growth as they occur in caves.

TRIM67 Protein Negatively Regulates Ras Activity through Degradation of 80K-H and Induces Neuritogenesis*

PubMed Central

Yaguchi, Hiroaki; Okumura, Fumihiko; Takahashi, Hidehisa; Kano, Takahiro; Kameda, Hiroyuki; Uchigashima, Motokazu; Tanaka, Shinya; Watanabe, Masahiko; Sasaki, Hidenao; Hatakeyama, Shigetsugu

2012-01-01

Tripartite motif (TRIM)-containing proteins, which are defined by the presence of a common domain structure composed of a RING finger, one or two B-box motifs and a coiled-coil motif, are involved in many biological processes including innate immunity, viral infection, carcinogenesis, and development. Here we show that TRIM67, which has a TRIM motif, an FN3 domain and a SPRY domain, is highly expressed in the cerebellum and that TRIM67 interacts with PRG-1 and 80K-H, which is involved in the Ras-mediated signaling pathway. Ectopic expression of TRIM67 results in degradation of endogenous 80K-H and attenuation of cell proliferation and enhances neuritogenesis in the neuroblastoma cell line N1E-115. Furthermore, morphological and biological changes caused by knockdown of 80K-H are similar to those observed by overexpression of TRIM67. These findings suggest that TRIM67 regulates Ras signaling via degradation of 80K-H, leading to neural differentiation including neuritogenesis. PMID:22337885

TRIM67 protein negatively regulates Ras activity through degradation of 80K-H and induces neuritogenesis.

PubMed

Yaguchi, Hiroaki; Okumura, Fumihiko; Takahashi, Hidehisa; Kano, Takahiro; Kameda, Hiroyuki; Uchigashima, Motokazu; Tanaka, Shinya; Watanabe, Masahiko; Sasaki, Hidenao; Hatakeyama, Shigetsugu

2012-04-06

Tripartite motif (TRIM)-containing proteins, which are defined by the presence of a common domain structure composed of a RING finger, one or two B-box motifs and a coiled-coil motif, are involved in many biological processes including innate immunity, viral infection, carcinogenesis, and development. Here we show that TRIM67, which has a TRIM motif, an FN3 domain and a SPRY domain, is highly expressed in the cerebellum and that TRIM67 interacts with PRG-1 and 80K-H, which is involved in the Ras-mediated signaling pathway. Ectopic expression of TRIM67 results in degradation of endogenous 80K-H and attenuation of cell proliferation and enhances neuritogenesis in the neuroblastoma cell line N1E-115. Furthermore, morphological and biological changes caused by knockdown of 80K-H are similar to those observed by overexpression of TRIM67. These findings suggest that TRIM67 regulates Ras signaling via degradation of 80K-H, leading to neural differentiation including neuritogenesis.

Microstructure and Mechanical Properties of Fe-18Mn-18Cr-0.5N Austenitic Nonmagnetic Stainless Steel in Asymmetric Hot Rolling

NASA Astrophysics Data System (ADS)

Song, Y. L.; Li, C. S.; Ma, B.; Han, Y. H.

2017-05-01

Asymmetric hot rolling (ASHR) with a mismatch speed ratio of 1.15 in a single pass was applied to Fe-18Mn-18Cr-0.5N steel and was compared with symmetric hot rolling (SHR). The results indicated that a through-thickness microstructure gradient was formed in the plate due to the shear strain (0.36) introduced by ASHR. A fine-grained layer with the average size of 3 μm was achieved at the top surface of ASHR plate, while numerous elongated grains with a few recrystallized grains were presented at the center layer. The texture was distributed randomly at the top surface of ASHR plate, and a weaker intensity of typical hot-rolled texture in austenitic steel was obtained at the center layer of ASHR plate compared to SHR plate. An excellent combination of microhardness, strength and ductility was obtained in the ASHR plate, which was attributed to gradient microstructure induced by ASHR.

Fracture toughness and Charpy impact properties of several RAFMS before and after irradiation in HFIR

NASA Astrophysics Data System (ADS)

Sokolov, M. A.; Tanigawa, H.; Odette, G. R.; Shiba, K.; Klueh, R. L.

2007-08-01

As part of the development of candidate reduced-activation ferritic steels for fusion applications, several steels, namely F82H, 9Cr-2WVTa steels and F82H weld metal, are being investigated in the joint DOE-JAEA collaboration program. Within this program, three capsules containing a variety of specimen designs were irradiated at two design temperatures in the ORNL High Flux Isotope Reactor (HFIR). Two capsules, RB-11J and RB-12J, were irradiated in the HFIR removable beryllium positions with europium oxide (Eu 2O 3) thermal neutron shields in place. Specimens were irradiated up to 5 dpa. Capsule JP25 was irradiated in the HFIR target position to 20 dpa. The design temperatures were 300 °C and 500 °C. Precracked third-sized V-notch Charpy (3.3 × 3.3 × 25.4 mm) and 0.18 T DC(T) specimens were tested to determine transition and ductile shelf fracture toughness before and after irradiation. The master curve methodology was applied to evaluate the fracture toughness transition temperature, T0. Irradiation induced shifts of T0 and reductions of JQ were compared with Charpy V-notch impact properties. Fracture toughness and Charpy shifts were also compared to hardening results.

Concepts for the Development of a Nondestructive Testing and Evaluation System for Rigid Airfield Pavements.

DTIC Science & Technology

1985-01-01

T01A 141 401 619 4.89 3.38 2.98 3.71 4.18 3.83 T03A 41 488 708 5.09 5.09 5.09 42 347 564 2.52 2.52 43 406 695 4.98 4.98 T05A 39 537 757 5.74 5.75 5.75...r N0fl Nl 0 P NN0N eNON,0 f0NrO N 0200 gomlf Onnin 1n00 0000 nOwo aNt 0 cu1-W O l Mef 0qb (A vN N flONQ N N* N NNM ycN ty ,NN c 0 0 0 mNf YOJ l PN 0

Physics basis for an advanced physics and advanced technology tokamak power plant configuration: ARIES-ACT1

DOE PAGES

Kessel, C. E.; Poli, F. M.; Ghantous, K.; ...

2015-01-01

Here, the advanced physics and advanced technology tokamak power plant ARIES-ACT1 has a major radius of 6.25 m at an aspect ratio of 4.0, toroidal field of 6.0 T, strong shaping with elongation of 2.2, and triangularity of 0.63. The broadest pressure cases reached wall-stabilized β N ~ 5.75, limited by n = 3 external kink mode requiring a conducting shell at b/a = 0.3, requiring plasma rotation, feedback, and/or kinetic stabilization. The medium pressure peaking case reaches β N = 5.28 with B T = 6.75, while the peaked pressure case reaches β N < 5.15. Fast particle magnetohydrodynamicmore » stability shows that the alpha particles are unstable, but this leads to redistribution to larger minor radius rather than loss from the plasma. Edge and divertor plasma modeling shows that 75% of the power to the divertor can be radiated with an ITER-like divertor geometry, while >95% can be radiated in a stable detached mode with an orthogonal target and wide slot geometry. The bootstrap current fraction is 91% with a q95 of 4.5, requiring ~1.1 MA of external current drive. This current is supplied with 5 MW of ion cyclotron radio frequency/fast wave and 40 MW of lower hybrid current drive. Electron cyclotron is most effective for safety factor control over ρ~0.2 to 0.6 with 20 MW. The pedestal density is ~0.9×10 20/m 3, and the temperature is ~4.4 keV. The H98 factor is 1.65, n/n Gr = 1.0, and the ratio of net power to threshold power is 2.8 to 3.0 in the flattop.« less

Sphingobium barthaii sp. nov., a high molecular weight polycyclic aromatic hydrocarbon-degrading bacterium isolated from cattle pasture soil.

PubMed

Maeda, Allyn H; Kunihiro, Marie; Ozeki, Yasuhiro; Nogi, Yuichi; Kanaly, Robert A

2015-09-01

A Gram-stain-negative, yellow, rod-shaped bacterium, designated strain KK22(T), was isolated from a microbial consortium that grew on diesel fuel originally recovered from cattle pasture soil. Strain KK22(T) has been studied for its ability to biotransform high molecular weight polycyclic aromatic hydrocarbons. On the basis of 16S rRNA gene sequence phylogeny, strain KK22(T) was affiliated with the genus Sphingobium in the phylum Proteobacteria and was most closely related to Sphingobium fuliginis TKP(T) (99.8%) and less closely related to Sphingobium quisquiliarum P25(T) (97.5%). Results of DNA-DNA hybridization (DDH) revealed relatedness values between strain KK22(T) and strain TKP(T) and between strain KK22(T) and strain P25(T) of 21 ± 4% (reciprocal hybridization, 27 ± 2%) and 15 ± 2% (reciprocal hybridization, 17 ± 1%), respectively. Chemotaxonomic analyses of strain KK22(T) showed that the major respiratory quinone was ubiquinone Q-10, that the polar lipid profile consisted of phosphatidylglycerol, phosphatidylethanolamine, phosphatidylcholine, phosphatidyl-N-methylethylethanolamine and sphingoglycolipid, and that C18 : 1ω7c and C14 : 0 2-OH were the main fatty acid and hydroxylated fatty acids, respectively. This strain was unable to reduce nitrate and the genomic DNA G+C content was 64.7 mol%. Based upon the results of the DDH analyses, the fact that strain KK22(T) was motile, and its biochemical and physiological characteristics, strain KK22(T) could be separated from recognized species of the genus Sphingobium. We conclude that strain KK22(T) represents a novel species of this genus for which the name Sphingobium barthaii sp. nov. is proposed; the type strain is KK22(T) ( = DSM 29313(T) = JCM 30309(T)).

IMRT for Sinonasal Tumors Minimizes Severe Late Ocular Toxicity and Preserves Disease Control and Survival

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duprez, Frederic, E-mail: frederic.duprez@ugent.be; Madani, Indira; Morbee, Lieve

2012-05-01

Purpose: To report late ocular (primary endpoint) and other toxicity, disease control, and survival (secondary endpoints) after intensity-modulated radiotherapy (IMRT) for sinonasal tumors. Methods and Materials: Between 1998 and 2009, 130 patients with nonmetastatic sinonasal tumors were treated with IMRT at Ghent University Hospital. Prescription doses were 70 Gy (n = 117) and 60-66 Gy (n = 13) at 2 Gy per fraction over 6-7 weeks. Most patients had adenocarcinoma (n = 82) and squamous cell carcinoma (n = 23). One hundred and one (101) patients were treated postoperatively. Of 17 patients with recurrent tumors, 9 were reirradiated. T-stages weremore » T1-2 (n = 39), T3 (n = 21), T4a (n = 38), and T4b (n = 22). Esthesioneuroblastoma was staged as Kadish A, B, and C in 1, 3, and 6 cases, respectively. Results: Median follow-up was 52, range 15-121 months. There was no radiation-induced blindness in 86 patients available for late toxicity assessment ({>=}6 month follow-up). We observed late Grade 3 tearing in 10 patients, which reduced to Grade 1-2 in 5 patients and Grade 3 visual impairment because of radiation-induced ipsilateral retinopathy and neovascular glaucoma in 1 patient. There was no severe dry eye syndrome. The worst grade of late ocular toxicity was Grade 3 (n = 11), Grade 2 (n = 31), Grade 1 (n = 33), and Grade 0 (n = 11). Brain necrosis and osteoradionecrosis occurred in 6 and 1 patients, respectively. Actuarial 5-year local control and overall survival were 59% and 52%, respectively. On multivariate analysis local control was negatively affected by cribriform plate and brain invasion (p = 0.044 and 0.029, respectively) and absence of surgery (p = 0.009); overall survival was negatively affected by cribriform plate and orbit invasion (p = 0.04 and <0.001, respectively) and absence of surgery (p = 0.001). Conclusions: IMRT for sinonasal tumors allowed delivering high doses to targets at minimized ocular toxicity, while maintaining disease control and survival. Avoidance of severe dry eye syndrome and radiation-induced blindness suggests IMRT as a standard treatment for sinonasal tumors.« less

Crustal Structure of Khövsgöl, Mongolia

NASA Astrophysics Data System (ADS)

Scott, A. M.; Meltzer, A.; Stachnik, J.; Russo, R.; Munkhuu, U.; Tsagaan, B.

2017-12-01

Mongolia is part of the Central Asian Orogenic Belt, an accretionary event that spanned 800 million years from the mid-Proterozoic to mid-Phanerozoic. As a result of the past collisional and rifting events, the modern Khövsgöl rift system of northern Mongolia contains a heterogeneous lithospheric structure. The current rift system has three parallel N-S trending basins that roughly align with terrane boundaries. Structures inherited during the accretionary events may be a factor influencing regional deformation. The forces that drive local deformation are not well understood, but varying processes have been proposed: far-field effects of India-Eurasian plate convergence, westward subduction of the Pacific plate, magmatic underplating at the base of the crust, mantle plume activity, and asthenospheric mantle convection. Determining the nature of crustal features within this poorly understood region may illuminate processes that control rifting within intracontinental settings. A network of 26 broadband seismic stations encompassing 200 square kilometers of the Khövsgöl rift system were deployed from August 2014 to June 2016. More than 2100 events were detected, and most earthquakes were concentrated near rift structures. Events between Busiin-Gol and Darkhad, the westernmost and central basins of the Khövsgöl rift system, are distributed within the crust. An active fault is outlined along the eastern border of the Darkhad basin. Khövsgöl earthquakes bound both sides of the rift. Along the northern border of Lake Khövsgöl, seismic events define a shallow active fault orthogonal to the basin. The largest event recorded within the network was a magnitude ml=5.2 located near the northeastern border of Lake Khövsgöl on 12-05-2014. The focal mechanism of this earthquake is predominantly strike-slip, but also includes an extensional component. This work focuses on earthquake relocation and calculating moment tensors and focal mechanisms of larger regional events to extract additional information about the local faults and their relationship to preexisting structures.

The Mechanism of High Strength-Ductility Steel Produced by a Novel Quenching-Partitioning-Tempering Process and the Mechanical Stability of Retained Austenite at Elevated Temperatures

NASA Astrophysics Data System (ADS)

Zhou, S.; Zhang, K.; Wang, Y.; Gu, J. F.; Rong, Y. H.

2012-03-01

The designed steel of Fe-0.25C-1.5Mn-1.2Si-1.5Ni-0.05Nb (wt pct) treated by a novel quenching-partitioning-tempering (Q-P-T) process demonstrates an excellent product of strength and elongation (PSE) at deformed temperatures from 298 K to 573 K (25 °C to 300 °C) and shows a maximum value of PSE (over 27,000 MPa pct) at 473 K (200 °C). The results fitted by the exponent decay law indicate that the retained austenite fraction with strain at a deformed temperature of 473 K (200 °C) decreases slower than that at 298 K (25 °C); namely, the transformation induced plasticity (TRIP) effect occurs in a larger strain range at 473 K (200 °C) than at 298 K (25 °C), showing better mechanical stability. The work-hardening exponent curves of Q-P-T steel further indicate that the largest plateau before necking appears at the deformed temperature of 473 K (200 °C), showing the maximum TRIP effect, which is due to the mechanical stability of considerable retained austenite. The microstructural characterization reveals that the high strength of Q-P-T steels results from dislocation-type martensite laths and dispersively distributed fcc NbC or hcp ɛ-carbides in martensite matrix, while excellent ductility is attributed to the TRIP effect produced by considerable retained austenite.

Titanium isopropoxide complexes of a series of sterically demanding aryloxo based [N2O2]2- ligands as precatalysts for ethylene polymerization.

PubMed

Panda, Manas K; Kaur, Sukhdeep; Reddy, Annapureddy Rajasekhar; Shaikh, Mobin M; Butcher, Ray J; Gupta, Virendrakumar; Ghosh, Prasenjit

2010-12-07

Several titanium isopropoxide complexes [N,N'-bis(2-oxo-3-R(1)-5-R(2)-phenylmethyl)-N,N'-bis(methylene-p-R(3)-C(6)H(4))-ethylenediamine]Ti(O(i)Pr)(2) [R(1) = t-Bu, R(2) = Me, R(3) = H (1b); R(1) = R(2) = t-Bu, R(3) = H, (2b); R(1) = R(2) = Cl, R(3) = H, (3b), R(1) = t-Bu, R(2) = Me, R(3) = Cl (4b); R(1) = R(2) = t-Bu, R(3) = Cl, (5b); R(1) = R(2) = R(3) = Cl, (6b)] supported over sterically demanding aryloxy based [N(2)O(2)]H(2) ligands have been designed as precatalysts for the ethylene polymerization. Specifically, the 1b-6b complexes, when treated with methylaluminoxane (MAO) under 88 ± 0.5 psi of ethylene at 30 °C for 3 h, produced polyethylene polymers of high molecular weight (M(w) = ca. 7.2-8.3 × 10(5) g mol(-1)) having broad molecular weight distribution (PDI = ca. 13.1-14.6). The 1b-6b complexes were conveniently synthesized from the direct reaction of the [N(2)O(2)]H(2) ligands, 1a-6a, with Ti(O(i)Pr)(4) in 69-86% yield.

Ruthenium complexes containing 2-(2-nitrosoaryl)pyridine: structural, spectroscopic, and theoretical studies.

PubMed

Chan, Siu-Chung; Cheung, Ho-Yuen; Wong, Chun-Yuen

2011-11-21

Ruthenium complexes containing 2-(2-nitrosoaryl)pyridine (ON(^)N) and tetradentate thioether 1,4,8,11-tetrathiacyclotetradecane ([14]aneS4), [Ru(ON(^)N)([14]aneS4)](2+) [ON(^)N = 2-(2-nitrosophenyl)pyridine (2a), 10-nitrosobenzo[h]quinoline (2b), 2-(2-nitroso-4-methylphenyl)pyridine, (2c), 2-(2-nitrosophenyl)-5-(trifluoromethyl)pyridine (2d)] and analogues with the 1,4,7-trithiacyclononane ([9]aneS3)/tert-butylisocyanide ligand set, [Ru(ON(^)N)([9]aneS3)(C≡N(t)Bu)](2+) (4a and 4b), have been prepared by insertion of a nitrosonium ion (NO(+)) into the Ru-aryl bond of cyclometalated ruthenium(II) complexes. The molecular structures of the ON(^)N-ligated complexes 2a and 2b reveal that (i) the ON(^)N ligands behave as bidentate chelates via the two N atoms and the bite angles are 86.84(18)-87.83(16)° and (ii) the Ru-N(NO) and N-O distances are 1.942(5)-1.948(4) and 1.235(6)-1.244(5) Å, respectively. The Ru-N(NO) and N-O distances, together with ν(N═O), suggest that the coordinated ON(^)N ligands in this work are neutral moiety (ArNO)(0) rather than monoanionic radical (ArNO)(•-) or dianion (ArNO)(2-) species. The nitrosated complexes 2a-2d show moderately intense absorptions centered at 463-484 nm [ε(max) = (5-6) × 10(3) dm(3) mol(-1) cm(-1)] and a clearly discriminable absorption shoulder around 620 nm (ε(max) = (6-9) × 10(2) dm(3) mol(-1) cm(-1)), which tails up to 800 nm. These visible absorptions are assigned as a mixing of d(Ru) → ON(^)N metal-to-ligand charge-transfer and ON(^)N intraligand transitions on the basis of time-dependent density functional theory (TD-DFT) calculations. The first reduction couples of the nitrosated complexes range from -0.53 to -0.62 V vs Cp(2)Fe(+/0), which are 1.1-1.2 V less negative than that for [Ru(bpy)([14]aneS4)](2+) (bpy = 2,2'-bipyridine). Both electrochemical data and DFT calculations suggest that the lowest unoccupied molecular orbitals of the nitrosated complexes are ON(^)N-centered. Natural population analysis shows that the amount of positive charge on the Ru centers and the [Ru([14]aneS4)] moieties in 2a and 2b is larger than that in [Ru(bpy)([14]aneS4)](2+). According to the results of the structural, spectroscopic, electrochemical, and theoretical investigations, the ON(^)N ligands in this work have considerable π-acidic character and behave as better electron acceptors than bpy.

Very large cooperative effects in heterobimetallic titanium-chromium catalysts for ethylene polymerization/copolymerization.

PubMed

Liu, Shaofeng; Motta, Alessandro; Mouat, Aidan R; Delferro, Massimiliano; Marks, Tobin J

2014-07-23

The heterobimetallic complexes, (η(5)-indenyl)[1-Me2Si((t)BuN)TiCl2]-3-CnH2n-[N,N-bis(2-(ethylthio)ethyl)amine]CrCl3 (n = 0, Ti-C0-Cr(SNS); n = 2, Ti-C2-Cr(SNS); n = 6, Ti-C6-Cr(SNS)), (η(5)-indenyl)[1-Me2Si((t)BuN)TiCl2]-3-C2H4-[N,N-bis((o-OMe-C6H4)2P)amine]CrCl3 (Ti-C2-Cr(PNP)), and (η(5)-indenyl)[1-Me2Si((t)BuN)TiCl2]-3-C2H4-[N,N-bis((diethylamine)ethyl)-amine]CrCl3 (Ti-C2-Cr(NNN)), are synthesized, fully characterized, and employed as olefin polymerization catalysts. With ethylene as the feed and MAO as cocatalyst/activator, SNS-based complexes Ti-C0-Cr(SNS), Ti-C2-Cr(SNS), and Ti-C6-Cr(SNS) afford linear low-density polyethylenes (LLDPEs) with exclusive n-butyl branches (6.8-25.8 branches/1000 C), while under identical polymerization conditions Ti-C2-Cr(PNP) and Ti-C2-Cr(NNN) produce polyethylenes with heterogeneous branching (C2, C4, and C≥6) or negligible branching, respectively. Under identical ethylene polymerization conditions, Ti-C0-Cr(SNS) produces polyethylenes with higher activity (4.5× and 6.1×, respectively), Mn (1.3× and 1.8×, respectively), and branch density (1.4× and 3.8×, respectively), than Ti-C2-Cr(SNS) and Ti-C6-Cr(SNS). Versus a CGC(Et)Ti + SNSCr tandem catalyst, Ti-C0-Cr(SNS) yields polyethylene with somewhat lower activity, but with 22.6× higher Mn and 4.0× greater branching density under identical conditions. In ethylene +1-pentene competition experiments, Ti-C0-Cr(SNS) yields 5.5% n-propyl branches and 94.5% n-butyl branches at [1-pentene] = 0.1 M, and the estimated effective local concentration of 1-hexene is ∼8.6 M. In contrast, the tandem CGC(Et)Ti + SNSCr system yields 91.0% n-propyl branches under identical reaction conditions. The homopolymerization and 1-pentene competition results argue that close Ti···Cr spatial proximity together with weak C-H···Ti and C-H···S interactions significantly influence relative 1-hexene enchainment and chain transfer rates, supported by DFT computation, and that such effects are conversion insensitive but cocatalyst and solvent sensitive.

Mantle Water Contents Beneath the Rio Grande Rift (NM, USA): FTIR Analysis of Rio Puerco and Kilbourne Hole Peridotite Xenoliths

NASA Technical Reports Server (NTRS)

Schaffer, L. A.; Peslier, A. H.; Brandon, A.; Selverstone, J.

2015-01-01

Peridotite xenoliths from the Rio Grande Rift (RGR) are being analyzed for H (sub 2) O contents by FTIR (Fourier Transform Infrared) as well as for major and trace element compositions. Nine samples are from the Rio Puerco Volcanic Field (RP) which overlaps the central RGR and southeastern Colorado Plateau; seventeen samples are from Kilbourne Hole (KH) in the southern RGR. Spinel Cr# (Cr/(Cr+Al)) (0.08-0.46) and olivine Mg# (Mg/(Mg plus Fe)) (0.883-0.911) of all RGR samples fall within the olivine-spinel mantle array from [1], an indicator that peridotites are residues of partial melting. Pyroxene H (sub 2) O in KH correlate with bulk rock and pyroxene Al (sub 2) O (sub 3).The KH clinopyroxene rare earth element (REE) variations fit models of 0-13 percent fractional melting of a primitive upper mantle. Most KH peridotites have bulk-rock light REE depleted patterns, but five are enriched in light REEs consistent with metasomatism. Variation in H (sub 2) O content is unrelated to REE enrichment. Metasomatism is seen in RP pyroxenite xenoliths [2] and will be examined in the peridotites studied here. Olivine H (sub 2) O contents are low (less than or equal to 15 parts per million), and decrease from core to rim within grains. This is likely due to H loss during xenolith transport by the host magma [3]. Diffusion models of H suggest that mantle H (sub 2) O contents are still preserved in cores of KH olivine, but not RP olivine. The average H (sub 2) O content of Colorado Plateau clinopyroxene (670 parts per million) [4] is approximately 300 parts per million higher than RGR clinopyroxene (350 parts per million). This upholds the hypothesis that hydration-induced lithospheric melting occurred during flat-slab subduction of the Farallon plate [5]. Numerical models indicate hydration via slab fluids is possible beneath the plateau, approximately 600 kilometers from the paleo-trench, but less likely approximately 850 kilometers away beneath the rift [6].

Sex-dependent association between erythrocyte n-3 PUFA and type 2 diabetes in older overweight people.

PubMed

Abbott, Kylie A; Veysey, Martin; Lucock, Mark; Niblett, Suzanne; King, Katrina; Burrows, Tracy; Garg, Manohar L

2016-04-01

The association between n-3 PUFA intake and type 2 diabetes (T2D) is unclear, and studies relating objective biomarkers of n-3 PUFA consumption to diabetic status remain limited. The aim of this study was to determine whether erythrocyte n-3 PUFA levels (n-3 index; n-3I) are associated with T2D in a cohort of older adults (n 608). To achieve this, the n-3I (erythrocyte %EPA+%DHA) was determined by GC and associated with fasting blood glucose; HbA1c; and plasma insulin. Insulin resistance (IR) was assessed using the homeostatic model assessment of insulin resistance (HOMA--IR). OR for T2D were calculated for each quartile of n-3I. In all, eighty-two type 2 diabetic (46·3 % female; 76·7 (sd 5·9) years) and 466 non-diabetic (57·9 % female; 77·8 (sd 7·1) years) individuals were included in the analysis. In overweight/obese (BMI≥27 kg/m2), the prevalence of T2D decreased across ascending n-3I quartiles: 1·0 (reference), 0·82 (95 % CI 0·31, 2·18), 0·56 (95 % CI 0·21, 1·52) and 0·22 (95 % CI 0·06, 0·82) (P trend=0·015). A similar but non-significant trend was seen in overweight men. After adjusting for BMI, no associations were found between n-3I and fasting blood glucose, HbA1c, insulin or HOMA-IR. In conclusion, higher erythrocyte n-3 PUFA status may be protective against the development of T2D in overweight women. Further research is warranted to determine whether dietary interventions that improve n-3 PUFA status can improve measures of IR, and to further elucidate sex-dependent differences.

SYNERGISTIC EFFECT OF HALIDE IONS ON THE CORROSION INHIBITION OF MILD STEEL IN SULPHURIC ACID USING METHYL, N-METHYL ETHYL AND ETHYL SUBSTITUTED γ-2,c-6-DIPHENYL PIPERIDIN-4-ONE SEMICARBAZONES

NASA Astrophysics Data System (ADS)

Priya, V. Shanmuga; Rani, C. Uma; Velrani, S.

The synergistic effect of halide ions such as KCl, KBr and KI on the corrosion inhibition of mild steel in 1 N sulphuric acid by γ-2,c-6-diphenyl-t-3-methyl piperdin-4-ones with semicarbazone (01SC), γ-2,c-6-diphenyl-N-methyl-t-3-ethyl piperdin-4-ones with semicarbazone (02SC) and 2,6-diphenyl-t-3-ethyl piperdin-4-one with semicarbazone (03SC) has been examined by weight loss method, potentiodynamic polarization measurements and electrochemical AC impedance spectroscopy. Results show that substituted γ-2,c-6-diphenyl piperidin-4-ones with semicarbazone act as the perfect corrosion inhibitors and their inhibition efficiency increases with the addition of halide ions. The inhibitor (01SC) shows the inhibition efficiency of 78.28% (0.2mM) by using a weight loss method. The influence of I-, Br- and Cl- anions raises the inhibition efficiency of the substituted 2,6-diphenyl piperidin-4-ones with semicarbazone due to the synergistic effect. The synergistic effect of halide ions was formed in the following order: KI > KBr > KCl.

Tool wear of (Ti, Al) N-coated polycrystalline cubic boron nitride compact in cutting of hardened steel

NASA Astrophysics Data System (ADS)

Wada, Tadahiro; Hanyu, Hiroyuki

2017-11-01

Polycrystalline cubic boron nitride compact (cBN) is effective tool material for cutting hardened steel. In addition to coated high speed steel and coated cemented carbide that has long been used for cutting materials, more recently, coated cBN has also been used. In this study, to verify the effectiveness of the (Ti,Al)N-coated cBN, which is formed on the substrate of cBN by the physical vapor deposition method, the hardened steel was turned with the (Ti,Al)N-coated cBN tool at a cutting speed of 3.33, 5.00 m/s, a feed rate of 0.3 mm/rev and a depth of cut of 0.1 mm. Furthermore, the uncoated cBN, which was the substrate of the (Ti,Al)N-coated, was also used. The tool wear of the cBN tools was experimentally investigated. The following results were obtained: (1) The contact area between the rake face and the chip of the (Ti,.Al)N-coated cBN tool was smaller than that of the uncoated cBN tool. (2) The tool wear of the (Ti,Al)N-coated cBN was smaller than that of uncoated cBN. (3) The wear progress of the (Ti,Al)N-coated cBN with the main element phase of the TiCN-Al, was slower than that of the (Ti,Al)N-coated cBN with the main element phase of the TiN-Al. (4) In the case of the high cutting speed of 5.00 m/s, the tool wear of the (Ti,Al)N-coated cBN was also smaller than that of uncoated cBN. The above results clarify that the (Ti,Al)N-coated cBN can be used as a tool material in high feed cutting of hardened steel.

Evaluation of frictional resistance and surface characteristics after immersion of orthodontic brackets and wire in different chemical solutions: A comparative in vitrostudy.

PubMed

Nanjundan, Kavitha; Vimala, G

2016-01-01

To evaluate the changes of static and kinetic frictional forces between the brackets and wires following exposure to a soft drink, acidic food ingredient, and acidulated fluoride prophylactic agents. Two types of Roth prescription mandibular incisor brackets were used: 3M Unitek Victory stainless steel (SS) brackets (n = 40) and Transcend 6000 polycrystalline alumina (PCA) brackets (n = 40) as well as eighty 0.019 × 0.025" dimension ortho technology SS wires of 50 mm length each. Subsequently, brackets tied with SS wires divided into eight subgroups (n = 10) and were immersed in vinegar (pH = 3.5 ± 0.5), Pepsi ® (pH = 2.46), Colgate Phos-Flur mouth rinse (pH = 5.1), and artificial saliva (control group pH = 7) for 24 h. Changes in surface morphology under scanning electron microscope ×1000, surface roughness (Ra) with surface profilometer (single bracket and single wire from each subgroup), and frictional resistance using universal testing machine were evaluated. Highest mean (standard deviation) static frictional force of 2.65 (0.25) N was recorded in Pepsi ® followed by 2.57 (0.25) N, 2.40 (0.22) N, and 2.36 (0.17) N for Vinegar, Colgate Phos-Flur mouth rinse, and artificial saliva groups, respectively. In a similar order, lesser mean kinetic frictional forces obtained. PCA brackets revealed more surface deterioration and higher frictional force values than SS brackets. A significant positive correlation was observed between frictional forces and bracket slot roughness (r = 0.861 and 0.802, respectively, for static and kinetic frictional forces, p < 0.001 for both) and wire roughness (r = 0.243 and 0.242, respectively, for static and kinetic frictional forces, p < 0.05 for both). Findings may have long-term implications when acidic food substances are used during fixed orthodontic treatment. Further, in vivo studies are required to analyze the clinical effect of acidic mediums in the oral environment during orthodontic treatment.

Determination of triterpene glycosides in sea cucumber (Stichopus japonicus) and its related products by high-performance liquid chromatography.

PubMed

Dong, Ping; Xue, Chang-Hu; Yu, Lin-Fang; Xu, Jie; Chen, Shi-Guo

2008-07-09

A creative and sensitive method has been developed for the determination of triterpene glycosides concentrations in sea cucumber ( Stichopus japonicus) and related products by using d-quinovose (6-deoxyglucose) as the measurement standard by reverse-phase high-performance liquid chromatography (HPLC) and variable-wavelength detection. d-quinovose, which is a unique monosaccharide in holostane triterpene glycosides, was liberated by acid hydrolysis and precolumn derivatized by 1-phenyl-3-methyl-5-pyrazolone (PMP). PMP-quinovose was analyzed by HPLC with 22% acetonitrile in 0.05 M KH2PO4 aquatic solution (pH 5.2) as mobile phase. The calibration curves of d-quinovose were linear within the range of 6.56-164 mg/L (r(2) > 0.995). The contents of triterpene glycosides in various S. japonicus products were determined after appropriate pretreatment methods. The concentration of triterpene glycosides was calculated by the formula C = C(qui) x alpha (alpha = 8.5). The result showed that this method was a simple, rapid, and stable method for the determination of triterpene glycosides in S. japonicus products.

Hancock IAP, Syracuse, New York. Revised Uniform Summary of Surface Weather Observations (RUSSWO). Parts A-F.

DTIC Science & Technology

1982-04-06

57.3 57.4 57." 57.4 5 7 .4 57.4 57.4 57.. 57.4 57.4 , 5 5 56.9 5§. 0-9.35.1 .- ,Z 2.l 5,;.8 54,C c .2 60.3 bJb 61.3 bl.4 61.4, 61.4 61.’. 61. 4 t .4...SUMMARY OF SURPR b2ti UNC.LASSIFIED U SAFETAC/OS-82/O2O SB1-AD-ESSO 164 N I hh Ih,,h ii1 111111111m 4I o5 AO_ IWA 1008 ’LAL CLIMATCLOGY BRACH -LTAC EXTREME...TEMPERATURE OEPRESSION (F) TOTAL TOTAL () 0 1-2 3-4 5 .6 7 5 9.I .2 22. (231S -67 I8I.02.2 2? 2 26127 2 29.-30 * 31OS’S. jb ., W..,I .b0. P..n* 7 / 77

Polymorphisms in Protein Tyrosine Phosphatase Non-receptor Type 2 and 22 (PTPN2/22) Are Linked to Hyper-Proliferative T-Cells and Susceptibility to Mycobacteria in Rheumatoid Arthritis

PubMed Central

Sharp, Robert C.; Beg, Shazia A.; Naser, Saleh A.

2018-01-01

A shared genetic pre-disposition, chronic inflammation, and treatment with similar biologics between Rheumatoid arthritis (RA) and Crohn's disease (CD) have intrigued us to investigate whether the two disorders share trigger association or possible causation. We hypothesized earlier that Single Nucleotide Polymorphisms (SNPs) in the negative regulators Protein Tyrosine Phosphatase Non-receptor type 2 and 22 (PTPN2/22) lead to a dysregulated immune response, susceptibility to environmental triggers, and continued apoptosis as seen in chronic inflammation in RA and CD. To test the hypothesis, peripheral leukocytes samples from 132 consented subjects were genotyped for 9 SNPs in PTPN2/22 using TaqMan™ genotyping. The effect of the SNPs on PTPN2/22 and IFN-γ expression was determined using real time PCR. T-cell proliferation and response to phytohematoagglutonin (PHA) mitogen and mycobacterial antigens were determined by BrdU proliferation assay. Blood samples were also analyzed for the Mycobacterium avium subspecies paratuberculosis (MAP) IS900 gene by nPCR. Out of 9 SNPs examined, heterozygous (TC) or minor (CC) alleles of PTPN2:rs478582 occurred in 79% RA compared to 60% healthy controls (p-values ≤ 0.05; OR = 2.28). Similarly, heterozygous (GA) or minor (AA) alleles of PTPN22:rs2476601 occurred in 29% RA compared to 6% healthy controls (p-values ≤ 0.05; OR = 5.90). PTPN2/22 expression in RA was decreased by 1.2-fold compared to healthy controls. PTPN2:rs478582 upregulated IFN-γ in RA by 1.5-fold. Combined PTPN2:rs478582 and PTPN22:rs2476601 increased T-cell proliferation by 2.7-fold when treated with PHA. Surprisingly, MAP DNA was detected in 34% of RA samples compared to 8% healthy controls, (p-values ≤ 0.05, OR = 5.74). RA samples with PTPN2:rs478582 and/or PTPN22:rs2476601 were more positive for MAP than samples without polymorphisms. Combined occurrence of PTPN2:rs478582 and PTPN22:rs2476601 in association with the presence of MAP has significantly increased T-cell response and elevated IFN-γ expression in RA samples. The data suggest that genetic polymorphisms may play vital role in T-cell regulation, susceptibility to mycobacteria and ultimately response to treatment. This is the first study to report the detection of MAP DNA in the blood of RA patients; further studies are needed using larger number of samples. PMID:29423382

Toward a feline-optimized culture medium: impact of ions, carbohydrates, essential amino acids, vitamins, and serum on development and metabolism of in vitro fertilization-derived feline embryos relative to embryos grown in vivo.

PubMed

Herrick, Jason R; Bond, Jennifer B; Magarey, Genevieve M; Bateman, Helen L; Krisher, Rebecca L; Dunford, Susan A; Swanson, William F

2007-05-01

The objective of this study was to define the physiologic needs of domestic cat embryos to facilitate development of a feline-specific culture medium. In a series of factorial experiments, in vivo-matured oocytes (n = 2040) from gonadotropin-treated domestic cats were inseminated in vitro to generate embryos (n = 1464) for culture. In the initial study, concentrations of NaCl (100.0 vs. 120.0 mM), KCl (4.0 vs. 8.0 mM), KH(2)PO(4) (0.25 vs. 1.0 mM), and the ratio of CaCl(2) to MgSO(4)-7H(2)O (1.0:2.0 mM vs. 2.0:1.0 mM) in the medium were evaluated during Days 1-6 (Day 0: oocyte recovery and in vitro fertilization [IVF]) of culture. Subsequent experiments assessed the effects of varying concentrations of carbohydrate (glucose, 1.5, 3.0, or 6.0 mM; l-lactate, 3.0, 6.0, or 12.0 mM; and pyruvate, 0.1 or 1.0 mM) and essential amino acids (EAAs; 0, 0.5, or 1.0x) in the medium during Days 1-3 and Days 3-6 of culture. Inclusion of vitamins (0 vs. 1.0x) and fetal calf serum (FCS; 0 vs. 5% [v/v]) in the medium also was evaluated during Days 3-6. Development and metabolism of IVF embryos on Day 3 or Day 6 were compared to age-matched in vivo embryos recovered from naturally mated queens. A feline-optimized culture medium (FOCM) was formulated based on these results (100.0 mM NaCl, 8.0 mM KCl, 1.0 mM KH(2)PO(4), 2.0 mM CaCl(2), 1.0 mM MgSO(4), 1.5 mM glucose, 6.0 mM L-lactate, 0.1 mM pyruvate, and 0x EAAs with 25.0 mM NaHCO(3), 1.0 mM alanyl-glutamine, 0.1 mM taurine, and 1.0x nonessential amino acids) with 0.4% (w/v) BSA from Days 0-3 and 5% FCS from Days 3-6. Using this medium, ~70% of cleaved embryos developed into blastocysts with profiles of carbohydrate metabolism similar to in vivo embryos. Our results suggest that feline embryos have stage-specific responses to carbohydrates and are sensitive to EAAs but are still reliant on one or more unidentified components of FCS for optimal blastocyst development.

Welding of HSLA-100 steel using ultra low carbon bainitic weld metal to eliminate preheating

DOE Office of Scientific and Technical Information (OSTI.GOV)

Devletian, J.H.; Singh, D.; Wood, W.E.

1996-12-31

Advanced high strength steels such as the Navy`s HSLA-100 and HSLA-80 contain sufficiently low carbon levels to be weldable without preheating. Unfortunately, commercial filler metals specifically designed to weld these steels without costly preheating have not yet been developed. The objective of this paper is to show that the Navy`s advanced steels can be welded by gas metal-arc (GMAW) and gas tungsten-arc welding (GTAW) without preheating by using filler metal compositions that produce weld metal with an ultra-low carbon bainitic (ULCB) microstructure. Filler metals were fabricated from vacuum induction melted (VIM) ingots containing ultra-low levels of C, O and N.more » HSLA-100 plate and plate from the VIM ingots were welded by both GMAW and GTAW with Ar-5% CO{sub 2} shielding gas using welding conditions to achieve cooling times from 800 to 500 C (t{sub 8-5}) from 35 to 14 sec. Weld metal tensile, hardness and CVN impact toughness testing as well as microstructural studies using transmission electron microscopy were conducted. The ULCB weld metal was relatively insensitive to cooling rate, resulting in good strength and toughness values over a wide range of t{sub 8-5} cooling times. Filler metal compositions which met the mechanical property requirements for HSLA-100, HSLA-80 and HSLA-65 weld metal were developed.« less

A neutron activation analysis procedure for the determination of uranium, thorium and potassium in geologic samples

USGS Publications Warehouse

Aruscavage, P. J.; Millard, H.T.

1972-01-01

A neutron activation analysis procedure was developed for the determination of uranium, thorium and potassium in basic and ultrabasic rocks. The three elements are determined in the same 0.5-g sample following a 30-min irradiation in a thermal neutron flux of 2??1012 n??cm-2??sec-1. Following radiochemical separation, the nuclides239U (T=23.5 m),233Th (T=22.2 m) and42K (T=12.36 h) are measured by ??-counting. A computer program is used to resolve the decay curves which are complex owing to contamination and the growth of daughter activities. The method was used to determine uranium, throium and potassium in the U. S. Geological Survey standard rocks DTS-1, PCC-1 and BCR-1. For 0.5-g samples the limits of detection for uranium, throium and potassium are 0.7, 1.0 and 10 ppb, respectively. ?? 1972 Akade??miai Kiado??.

Measurements of ion stopping around the Bragg peak in high-energy-density plasmas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Frenje, J. A.; Grabowski, P. E.; Li, C. K.

2015-11-09

For the first time, quantitative measurements of ion stopping at energies about the Bragg peak (or peak ion stopping, which occurs at an ion velocity comparable to the average thermal electron velocity), and its dependence on electron temperature (T e) and electron number density (n e) in the range of 0.5 – 4.0 keV and 3 × 10 22 – 3 × 10 23 cm -3 have been conducted, respectively. It is experimentally demonstrated that the position and amplitude of the Bragg peak varies strongly with T e with n e. As a result, the importance of including quantum diffractionmore » is also demonstrated in the stopping-power modeling of High-Energy-Density Plasmas.« less

Does growth path influence beef lipid deposition and fatty acid composition?

PubMed Central

Costa, Ana S. H.; Alves, Susana P.; Alfaia, Cristina M.; Prates, José A. M.; Vleck, Veronica; Cassar-Malek, Isabelle; Hocquette, Jean-François; Bessa, Rui J. B.

2018-01-01

Despite the recent advances in transcriptomics, gene expression studies addressing cattle´s skeletal muscle adaptations in response to compensatory growth are warranted, particularly regarding lipid metabolism due to its impact in meat sensory and nutritional traits. In the present study, in comparison to ad libitum feeding, a period of feed restriction was used in order to understand the changes in bull´s lipid metabolism and gene expression of the adipogenic and lipogenic pathways after re-alimentation. Thus, 40 young Alentejana bulls were either fed ad libitum (CG group) from 9 to 18 months of age or subjected to food restriction from 9 to 15 months of age, and fed ad libitum until 24 months of age (DG group). The intramuscular fat (IMF) and total fatty acids (FA) contents were similar between groups. The major FA (>2%) contents were similar (16:0, 16:1c9, 18:1c9 and 18:2n-6) between treatments with the exception of 18:0 content that was 15% lower in DG than in CG and 20:4n-6 that tended to be greater on DG bulls. Regarding minor FA (<2%), the DG group presented greater proportions (P<0.01) of 17:1c9, 18:1t9, 18:1t10 (, 18:1c11), 18:1c13, 18:3n-6, 22:0, 22:4n-6 and 22:6n-3 and lower (P<0.05) proportions of 20:0, 18:1t16+c14, and branched chain FA (iso-15:0, anteiso-15:0, iso-16:0 and anteiso-17:0) than the CG group. Delta-9 desaturase activity indices were consistently greater (P<0.05) in DG, when compared to the CG group. Regarding microarray analysis, differentially expressed genes between CG and DG bulls were grouped in 5 main biological functions: lipid and nucleic acid metabolisms, small molecule biochemistry, molecular transport and translational modification. Discontinuous growth down-regulated the expression of ACACB (FC (fold-change) = 1.32), FABP3 (FC = 1.45), HADHA (FC = 1.41) and SLC37A4 (FC = 1.40) genes, when compared to the CG system (FDR<0.05). In contrast, in the CG bulls, the expression of ELOVL5 (FC = 1.58) and FASN (FC = 1.71) was down-regulated when compared to DG bulls. These results were confirmed to be significant (P<0.05) in the case of ELOVL5, FASN and SLC37A4, and almost significant for FABP3 by qRT-PCR analysis. The SCD1 and SCD5 gene expressions were not found to be affected by growth path. These results contribute to the still scarce knowledge about the mechanisms involved in fatty acid metabolism during compensatory growth which have decisive role on meat quality produced in Mediterranean areas. PMID:29614102

Effects of oxygen content on the oxidation process of Si-containing steel during anisothermal heating

NASA Astrophysics Data System (ADS)

Yuan, Qing; Xu, Guang; Liang, Wei-cheng; He, Bei; Zhou, Ming-xing

2018-02-01

The oxidizing behavior of Si-containing steel was investigated in an O2 and N2 binary-component gas with oxygen contents ranging between 0.5vol% and 4.0vol% under anisothermal-oxidation conditions. A simultaneous thermal analyzer was employed to simulate the heating process of Si-containing steel in industrial reheating furnaces. The oxidation gas mixtures were introduced from the commencement of heating. The results show that the oxidizing rate remains constant in the isothermal holding process at high temperatures; therefore, the mass change versus time presents a linear law. A linear relation also exists between the oxidizing rate and the oxygen content. Using the linear regression equation, the oxidation rate at different oxygen contents can be predicted. In addition, the relationship between the total mass gain and the oxygen content is linear; thus, the total mass gain at oxygen contents between 0.5vol%-4.0vol% can be determined. These results enrich the theoretical studies of the oxidation process in Si-containing steels.

A Study of Mechanical Alloying of Metal Powders

DTIC Science & Technology

1981-05-01

UYON STAYt~ENT (d ida .... Approved for public release, distribution unlimited -𔄁. "’ I’ T PJIu TIO N IT A T EMT• ( ofe~ • e ao . m .. M•A 2-9, If...RELATIVE INTENSITY OF TIlE (1i1) BRAGG REFLECTION, 316 STAINLESS STEEL ,. 2.5 w/o Ti02 POWDER MILLED 98 HOURS AT 300 RPM...micrograph. 316.2.5 w/o Ti02 milled at 󈨋 300 RPM. Annealed 1.5 hours at 11000C. 30. Micrographs, iron - 10 w/o TiO2 milled 64 hours 72 at 300 RIh

Effect of stresses on the structural changes in high-chromium steel upon creep

NASA Astrophysics Data System (ADS)

Fedoseeva, A. E.; Dudova, N. R.; Kaibyshev, R. O.

2017-06-01

The effect of stresses on the microstructure and dispersed particles in a heating-performance Fe‒0.12C-0.06Si-0.04Ni-0.2Mn-9.5Cr-3.2Co-0.45Mo-3.1W-0.2V-0.06Nb-0.005B-0.05N (wt %) steel has been studied under long-term strength tests at T = 650°C under initial applied stresses ranging from 220 to 100 MPa with a step of 20 MPa. Under an applied stress of 160 MPa, which corresponds to a time to fracture of 1703 h, a transfer from short- to long-term creep takes place. It has been shown that alloying with 3% Co and an increase in W content to 3% significantly increase the short-term creep resistance and slightly increase the long-term strength upon tests by more than 104 h. The transfer from short- to the long-term creep is accompanied by substantial changes in the microstructure of the steel. Under long-term creep, the solid solution became depleted of tungsten and of molybdenum down to the thermodynamically equilibrium content of these elements in the solid solution, which leads to the precipitation of a large amount of fine particles of the Laves phase at the boundaries of laths and prior austenitic grains. At a time to fracture of more than 4 × 103 h, the coalescence of the M23C6 carbides and Laves-phase particles occurs, which causes the transformation of the structure of fine tempered martensite lath structure into a subgrained structure.