Comparison of structural and least-squares lines for estimating geologic relations

USGS Publications Warehouse

Williams, G.P.; Troutman, B.M.

1990-01-01

Two different goals in fitting straight lines to data are to estimate a "true" linear relation (physical law) and to predict values of the dependent variable with the smallest possible error. Regarding the first goal, a Monte Carlo study indicated that the structural-analysis (SA) method of fitting straight lines to data is superior to the ordinary least-squares (OLS) method for estimating "true" straight-line relations. Number of data points, slope and intercept of the true relation, and variances of the errors associated with the independent (X) and dependent (Y) variables influence the degree of agreement. For example, differences between the two line-fitting methods decrease as error in X becomes small relative to error in Y. Regarding the second goal-predicting the dependent variable-OLS is better than SA. Again, the difference diminishes as X takes on less error relative to Y. With respect to estimation of slope and intercept and prediction of Y, agreement between Monte Carlo results and large-sample theory was very good for sample sizes of 100, and fair to good for sample sizes of 20. The procedures and error measures are illustrated with two geologic examples. ?? 1990 International Association for Mathematical Geology.

Relationships among the slopes of lines derived from various data analysis techniques and the associated correlation coefficient

NASA Technical Reports Server (NTRS)

Cohen, S. C.

1980-01-01

A technique for fitting a straight line to a collection of data points is given. The relationships between the slopes and correlation coefficients, and between the corresponding standard deviations and correlation coefficient are given.

A novel line segment detection algorithm based on graph search

NASA Astrophysics Data System (ADS)

Zhao, Hong-dan; Liu, Guo-ying; Song, Xu

2018-02-01

To overcome the problem of extracting line segment from an image, a method of line segment detection was proposed based on the graph search algorithm. After obtaining the edge detection result of the image, the candidate straight line segments are obtained in four directions. For the candidate straight line segments, their adjacency relationships are depicted by a graph model, based on which the depth-first search algorithm is employed to determine how many adjacent line segments need to be merged. Finally we use the least squares method to fit the detected straight lines. The comparative experimental results verify that the proposed algorithm has achieved better results than the line segment detector (LSD).

27 CFR 9.194 - San Antonio Valley.

Code of Federal Regulations, 2014 CFR

2014-04-01

... southeast in a straight line for approximately 5 miles across sections 24 and 25, T23S, R9E, and sections 30... Tierra Redonda Mountain map; then (3) Continue southeast in a straight line for approximately 3.25 miles... the Bradley map; then (4) Proceed straight south for approximately 2.5 miles along the eastern...

A method of plane geometry primitive presentation

NASA Astrophysics Data System (ADS)

Jiao, Anbo; Luo, Haibo; Chang, Zheng; Hui, Bin

2014-11-01

Point feature and line feature are basic elements in object feature sets, and they play an important role in object matching and recognition. On one hand, point feature is sensitive to noise; on the other hand, there are usually a huge number of point features in an image, which makes it complex for matching. Line feature includes straight line segment and curve. One difficulty in straight line segment matching is the uncertainty of endpoint location, the other is straight line segment fracture problem or short straight line segments joined to form long straight line segment. While for the curve, in addition to the above problems, there is another difficulty in how to quantitatively describe the shape difference between curves. Due to the problems of point feature and line feature, the robustness and accuracy of target description will be affected; in this case, a method of plane geometry primitive presentation is proposed to describe the significant structure of an object. Firstly, two types of primitives are constructed, they are intersecting line primitive and blob primitive. Secondly, a line segment detector (LSD) is applied to detect line segment, and then intersecting line primitive is extracted. Finally, robustness and accuracy of the plane geometry primitive presentation method is studied. This method has a good ability to obtain structural information of the object, even if there is rotation or scale change of the object in the image. Experimental results verify the robustness and accuracy of this method.

Advantages and disadvantages of straight-lined and nonstraight-lined organizations at the airway facilities training division of the Federal Aviation Administration Academy

NASA Astrophysics Data System (ADS)

McMullen, Jessie L.

Scope and method of study. This study describes the advantages and the disadvantages of straight-lined and nonstraight-lined organizations at the MMAC FAA Academy. The primary focus will be on the AF division within the FAA Academy. This study will assist in making sound decisions about which structure is better at the present time. Others who read this research will gain an awareness of advantages and disadvantages of each structure. The reason for focusing primarily on individuals from the FAA is because of their experience in straight-line and nonstraight-line organizations. Data were collected during the study and analyzed to determine what the majority of the candidates thought about the structure. Findings and conclusions. Many of the respondents believe the FAA Academy AF Division should be straight-lined to the AFZ organization in Headquarters. Most of the respondents still see the FAA organization as a closed-type structure with a top-down management style. Another important outcome of the findings was many of the respondents believed, regardless of the structure, employees should be empowered more and allowed to participate in the decision-making process. Based on the findings some of the advantages of straight-lined organizations were: it brings the parent organization in and gives them a first hand view of its operations, there is no middle person involved, and there is a direct line to parent organization. The disadvantages of straight-lined organizations based on the findings were: there is no middle management to speak to headquarters as an intermediator on training issues/concerns, it requires more resources and funding that may not be forthcoming, and it compels a parent organization to acquire more resources to handle its own business.

Resonant behaviour of MHD waves on magnetic flux tubes. III - Effect of equilibrium flow

NASA Technical Reports Server (NTRS)

Goossens, Marcel; Hollweg, Joseph V.; Sakurai, Takashi

1992-01-01

The Hollweg et al. (1990) analysis of MHD surface waves in a stationary equilibrium is extended. The conservation laws and jump conditions at Alfven and slow resonance points obtained by Sakurai et al. (1990) are generalized to include an equilibrium flow, and the assumption that the Eulerian perturbation of total pressure is constant is recovered as the special case of the conservation law for an equilibrium with straight magnetic field lines and flow along the magnetic field lines. It is shown that the conclusions formulated by Hollweg et al. are still valid for the straight cylindrical case. The effect of curvature is examined.

The new moon illusion and the role of perspective in the perception of straight and parallel lines.

PubMed

Rogers, Brian; Naumenko, Olga

2015-01-01

In the new moon illusion, the sun does not appear to be in a direction perpendicular to the boundary between the lit and dark sides of the moon, and aircraft jet trails appear to follow curved paths across the sky. In both cases, lines that are physically straight and parallel to the horizon appear to be curved. These observations prompted us to investigate the neglected question of how we are able to judge the straightness and parallelism of extended lines. To do this, we asked observers to judge the 2-D alignment of three artificial "stars" projected onto the dome of the Saint Petersburg Planetarium that varied in both their elevation and their separation in horizontal azimuth. The results showed that observers make substantial, systematic errors, biasing their judgments away from the veridical great-circle locations and toward equal-elevation settings. These findings further demonstrate that whenever information about the distance of extended lines or isolated points is insufficient, observers tend to assume equidistance, and as a consequence, their straightness judgments are biased toward the angular separation of straight and parallel lines.

Bloodstain Pattern Analysis: implementation of a fluid dynamic model for position determination of victims

PubMed Central

Laan, Nick; de Bruin, Karla G.; Slenter, Denise; Wilhelm, Julie; Jermy, Mark; Bonn, Daniel

2015-01-01

Bloodstain Pattern Analysis is a forensic discipline in which, among others, the position of victims can be determined at crime scenes on which blood has been shed. To determine where the blood source was investigators use a straight-line approximation for the trajectory, ignoring effects of gravity and drag and thus overestimating the height of the source. We determined how accurately the location of the origin can be estimated when including gravity and drag into the trajectory reconstruction. We created eight bloodstain patterns at one meter distance from the wall. The origin’s location was determined for each pattern with: the straight-line approximation, our method including gravity, and our method including both gravity and drag. The latter two methods require the volume and impact velocity of each bloodstain, which we are able to determine with a 3D scanner and advanced fluid dynamics, respectively. We conclude that by including gravity and drag in the trajectory calculation, the origin’s location can be determined roughly four times more accurately than with the straight-line approximation. Our study enables investigators to determine if the victim was sitting or standing, or it might be possible to connect wounds on the body to specific patterns, which is important for crime scene reconstruction. PMID:26099070

Bloodstain Pattern Analysis: implementation of a fluid dynamic model for position determination of victims.

PubMed

Laan, Nick; de Bruin, Karla G; Slenter, Denise; Wilhelm, Julie; Jermy, Mark; Bonn, Daniel

2015-06-22

Bloodstain Pattern Analysis is a forensic discipline in which, among others, the position of victims can be determined at crime scenes on which blood has been shed. To determine where the blood source was investigators use a straight-line approximation for the trajectory, ignoring effects of gravity and drag and thus overestimating the height of the source. We determined how accurately the location of the origin can be estimated when including gravity and drag into the trajectory reconstruction. We created eight bloodstain patterns at one meter distance from the wall. The origin's location was determined for each pattern with: the straight-line approximation, our method including gravity, and our method including both gravity and drag. The latter two methods require the volume and impact velocity of each bloodstain, which we are able to determine with a 3D scanner and advanced fluid dynamics, respectively. We conclude that by including gravity and drag in the trajectory calculation, the origin's location can be determined roughly four times more accurately than with the straight-line approximation. Our study enables investigators to determine if the victim was sitting or standing, or it might be possible to connect wounds on the body to specific patterns, which is important for crime scene reconstruction.

Bloodstain Pattern Analysis: implementation of a fluid dynamic model for position determination of victims

NASA Astrophysics Data System (ADS)

Laan, Nick; de Bruin, Karla G.; Slenter, Denise; Wilhelm, Julie; Jermy, Mark; Bonn, Daniel

2015-06-01

Bloodstain Pattern Analysis is a forensic discipline in which, among others, the position of victims can be determined at crime scenes on which blood has been shed. To determine where the blood source was investigators use a straight-line approximation for the trajectory, ignoring effects of gravity and drag and thus overestimating the height of the source. We determined how accurately the location of the origin can be estimated when including gravity and drag into the trajectory reconstruction. We created eight bloodstain patterns at one meter distance from the wall. The origin’s location was determined for each pattern with: the straight-line approximation, our method including gravity, and our method including both gravity and drag. The latter two methods require the volume and impact velocity of each bloodstain, which we are able to determine with a 3D scanner and advanced fluid dynamics, respectively. We conclude that by including gravity and drag in the trajectory calculation, the origin’s location can be determined roughly four times more accurately than with the straight-line approximation. Our study enables investigators to determine if the victim was sitting or standing, or it might be possible to connect wounds on the body to specific patterns, which is important for crime scene reconstruction.

27 CFR 9.179 - Southern Oregon.

Code of Federal Regulations, 2011 CFR

2011-04-01

... township line T22S-T23S; then (4) Proceed southeast approximately 8.5 miles along a straight line to the intersection of township line T23S-T24S with range line R7W-R8W; then south along the R7W-R8W range line... a straight line approximately 3.5 miles toward the intersection of township line T25S-T26S with...

27 CFR 9.179 - Southern Oregon.

Code of Federal Regulations, 2010 CFR

2010-04-01

... township line T22S-T23S; then (4) Proceed southeast approximately 8.5 miles along a straight line to the intersection of township line T23S-T24S with range line R7W-R8W; then south along the R7W-R8W range line... a straight line approximately 3.5 miles toward the intersection of township line T25S-T26S with...

27 CFR 9.223 - Coombsville.

Code of Federal Regulations, 2014 CFR

2014-04-01

... for 0.4 mile to the intersection of the 1,400-foot elevation line and an unnamed intermittent creek... straight line for 0.45 mile to the intersection of the 1,380-foot elevation line and an unnamed, unimproved...; then (3) Proceed south-southeast in a straight line for 0.6 mile to the unnamed 1,804-foot elevation...

27 CFR 9.223 - Coombsville.

Code of Federal Regulations, 2013 CFR

2013-04-01

... for 0.4 mile to the intersection of the 1,400-foot elevation line and an unnamed intermittent creek... straight line for 0.45 mile to the intersection of the 1,380-foot elevation line and an unnamed, unimproved...; then (3) Proceed south-southeast in a straight line for 0.6 mile to the unnamed 1,804-foot elevation...

27 CFR 9.223 - Coombsville.

Code of Federal Regulations, 2012 CFR

2012-04-01

... for 0.4 mile to the intersection of the 1,400-foot elevation line and an unnamed intermittent creek... straight line for 0.45 mile to the intersection of the 1,380-foot elevation line and an unnamed, unimproved...; then (3) Proceed south-southeast in a straight line for 0.6 mile to the unnamed 1,804-foot elevation...

Roadway data representation and application development : final report, December 2009.

DOT National Transportation Integrated Search

2009-08-06

The Straight-line Diagrammer, a web-based application to produce Straight-line Diagrams (SLDs) automatically, was developed in this project to replace old application (AutoSLD) which has outdated structure and limited capabilities.

The awakening of Attneave's sleeping cat: identification of everyday objects on the basis of straight-line versions of outlines.

PubMed

De Winter, Joeri; Wagemans, Johan

2008-01-01

Attneave (1954 Psychological Review 61 183-193) demonstrated that a line drawing of a sleeping cat can still be identified when the smoothly curved contours are replaced by straight-line segments connecting the positive maxima and negative minima of contour curvature. Using the set of line drawings by Snodgrass and Vanderwart (1980 Journal of Experimental Psychology: Human Learning and Memory 6 174-215) we made outline versions (with known curvature values along the contour) that can still be identified and that can be used to test Attneave's demonstration more systematically and more thoroughly. In five experiments (with 444 subjects in total), we tested identifiability of straight-line versions of 184 stimuli with different selections of points to be connected (using 24 to 28 subjects per stimulus per condition). Straight-line versions connecting curvature extrema were easier to identify than those based on inflections (where curvature changes sign), and those connecting salient points (determined by 161 independent subjects) were easier than those connecting midpoints. However, identification varied considerably between objects: some were almost always identifiable and others almost never, regardless of the selection criterion, whereas identifiability depended on the specific shape attributes preserved in the straight-line version of the outline in other objects. Results are discussed in relation to Attneave's original hypotheses as well as in the light of more recent theories on shape perception and object identification.

Power in randomized group comparisons: the value of adding a single intermediate time point to a traditional pretest-posttest design.

PubMed

Venter, Anre; Maxwell, Scott E; Bolig, Erika

2002-06-01

Adding a pretest as a covariate to a randomized posttest-only design increases statistical power, as does the addition of intermediate time points to a randomized pretest-posttest design. Although typically 5 waves of data are required in this instance to produce meaningful gains in power, a 3-wave intensive design allows the evaluation of the straight-line growth model and may reduce the effect of missing data. The authors identify the statistically most powerful method of data analysis in the 3-wave intensive design. If straight-line growth is assumed, the pretest-posttest slope must assume fairly extreme values for the intermediate time point to increase power beyond the standard analysis of covariance on the posttest with the pretest as covariate, ignoring the intermediate time point.

33 CFR 183.3 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... defined by a series of points of contact, with the boat structure, by straight lines at 45 degree angles... the line defined by a series of points of contact with the boat structure, by straight lines at 45 degree angles to the horizontal and contained in a vertical plane normal to the outside edge of the boat...

The comparison of Missouri mathematics project and teams games tournament viewed from emotional quotient eight grade student of junior school

NASA Astrophysics Data System (ADS)

Setyawan, Indra; Budiyono, Slamet, Isnandar

2017-08-01

This research was a quasi-experimental research with 2 × 3 factorial design. It aimed to determine the learning model between Missouri Mathematics Project (MMP) and Teams Games Tournament (TGT) that gave the best achievement on mathematics subject viewed from emotional quotient. The population of this research were all of Junior High School students at the 8th grade in Surakarta City, Central Java, Indonesia in academic year 2016/2017 which applied KTSP curriculum. The sample was taken by using stratified cluster random sampling. The data were collected by using methods of documentation, emotional quotient questionnaires, and mathematics achievement test. Data analysis technique used two ways analysis of variance (ANOVA) with unequal cell. According to the research findings, it could be concluded that: (1) students' mathematics achievement which were taught by using MMP is as good as emotional quotient achievement which were taught by using TGT in straight-line equation material, (2) mathematics achievement of students with high emotional quotient is better than students with medium and low emotional quotient, and mathematics achievement of students with medium emotional quotient is as good as students with low emotional quotient in straight-line equation material, (3) in each learning model, mathematics achievement of students with high emotional quotient is better than students with medium and low emotional quotient, and mathematics achievement of students with medium emotional quotient is as good as students with low emotional quotient in straight-line equation material (4) in each category of high and medium emotional quotient, student's mathematics achievement which were taught by using MMP is better than student's mathematics achievement which were taught by using TGT and in low emotional quotient student's mathematics achievement which were taught by using MMP is as good as student's mathematics achievement which were taught by using TGT in straight-line equation material.

Questa Baseline and Pre-Mining Ground-Water Quality Investigation. 24. Seismic Refraction Tomography for Volume Analysis of Saturated Alluvium in the Straight Creek Drainage and Its Confluence With Red River, Taos County, New Mexico

USGS Publications Warehouse

Powers, Michael H.; Burton, Bethany L.

2007-01-01

As part of a research effort directed by the New Mexico Environment Department to determine pre-mining water quality of the Red River at a molybdenum mining site in northern New Mexico, we used seismic refraction tomography to create subsurface compressional-wave velocity images along six lines that crossed the Straight Creek drainage and three that crossed the valley of Red River. Field work was performed in June 2002 (lines 1-4) and September 2003 (lines 5-9). We interpreted the images to determine depths to the water table and to the top of bedrock. Depths to water and bedrock in boreholes near the lines correlate well with our interpretations based on seismic data. In general, the images suggest that the alluvium in this area has a trapezoidal cross section. Using a U.S. Geological Survey digital elevation model grid of surface elevations of this region and the interpreted elevations to water table and bedrock obtained from the seismic data, we generated new models of the shape of the buried bedrock surface and the water table through surface interpolation and extrapolation. Then, using elevation differences between the two grids, we calculated volumes of dry and wet alluvium in the two drainages. The Red River alluvium is about 51 percent saturated, whereas the much smaller volume of alluvium in the tributary Straight Creek is only about 18 percent saturated. When combined with average ground-water velocity values, the information we present can be used to determine discharge of Straight Creek into Red River relative to the total discharge of Red River moving past Straight Creek. This information will contribute to more accurate models of ground-water flow, which are needed to determine the pre-mining water quality in the Red River.

Nanoscale shift of the intensity distribution of dipole radiation.

PubMed

Shu, Jie; Li, Xin; Arnoldus, Henk F

2009-02-01

The energy flow lines (field lines of the Poynting vector) for radiation emitted by a dipole are in general curves, rather than straight lines. For a linear dipole the field lines are straight, but when the dipole moment of a source rotates, the field lines wind numerous times around an axis, which is perpendicular to the plane of rotation, before asymptotically approaching a straight line. We consider an elliptical dipole moment, representing the most general state of oscillation, and this includes the linear dipole as a special case. Due to the spiraling near the source, for the case of a rotating dipole moment, the field lines in the far field are displaced with respect to the outward radial direction, and this leads to a shift of the intensity distribution of the radiation in the far field. This shift is shown to be independent of the distance to the source and, although of nanoscale dimension, should be experimentally observable.

26 CFR 1.9001 - Statutory provisions; Retirement-Straight Line Adjustment Act of 1958.

Code of Federal Regulations, 2010 CFR

2010-04-01

... line property on his 1956 adjustment date may elect to have this section apply. Such an election shall... beginning after December 31, 1940, and before January 1, 1956, changed from the retirement to the straight line method of computing the allowance of deductions for depreciation. (d) Basis adjustments as of 1956...

33 CFR 80.712 - Morris Island, SC to Hilton Head Island, SC.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Edisto River Entrance to the shore of Botany Bay Island. (d) A line drawn from the microwave antenna..., SC to Hilton Head Island, SC. (a) A straight line drawn from the seaward tangent of Folly Island through across Stono River to the shoreline of Sandy Point. (b) A straight line drawn from the seaward...

33 CFR 80.712 - Morris Island, SC to Hilton Head Island, SC.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Edisto River Entrance to the shore of Botany Bay Island. (d) A line drawn from the microwave antenna..., SC to Hilton Head Island, SC. (a) A straight line drawn from the seaward tangent of Folly Island through across Stono River to the shoreline of Sandy Point. (b) A straight line drawn from the seaward...

Straight line foraging in yellow-eyed penguins: new insights into cascading fisheries effects and orientation capabilities of marine predators.

PubMed

Mattern, Thomas; Ellenberg, Ursula; Houston, David M; Lamare, Miles; Davis, Lloyd S; van Heezik, Yolanda; Seddon, Philip J

2013-01-01

Free-ranging marine predators rarely search for prey along straight lines because dynamic ocean processes usually require complex search strategies. If linear movement patterns occur they are usually associated with travelling events or migratory behaviour. However, recent fine scale tracking of flying seabirds has revealed straight-line movements while birds followed fishing vessels. Unlike flying seabirds, penguins are not known to target and follow fishing vessels. Yet yellow-eyed penguins from New Zealand often exhibit directed movement patterns while searching for prey at the seafloor, a behaviour that seems to contradict common movement ecology theories. While deploying GPS dive loggers on yellow-eyed penguins from the Otago Peninsula we found that the birds frequently followed straight lines for several kilometres with little horizontal deviation. In several cases individuals swam up and down the same line, while some of the lines were followed by more than one individual. Using a remote operated vehicle (ROV) we found a highly visible furrow on the seafloor most likely caused by an otter board of a demersal fish trawl, which ran in a straight line exactly matching the trajectory of a recent line identified from penguin tracks. We noted high abundances of benthic scavengers associated with fisheries-related bottom disturbance. While our data demonstrate the acute way-finding capabilities of benthic foraging yellow-eyed penguins, they also highlight how hidden cascading effects of coastal fisheries may alter behaviour and potentially even population dynamics of marine predators, an often overlooked fact in the examination of fisheries' impacts.

Methods of Fitting a Straight Line to Data: Examples in Water Resources

USGS Publications Warehouse

Hirsch, Robert M.; Gilroy, Edward J.

1984-01-01

Three methods of fitting straight lines to data are described and their purposes are discussed and contrasted in terms of their applicability in various water resources contexts. The three methods are ordinary least squares (OLS), least normal squares (LNS), and the line of organic correlation (OC). In all three methods the parameters are based on moment statistics of the data. When estimation of an individual value is the objective, OLS is the most appropriate. When estimation of many values is the objective and one wants the set of estimates to have the appropriate variance, then OC is most appropriate. When one wishes to describe the relationship between two variables and measurement error is unimportant, then OC is most appropriate. Where the error is important in descriptive problems or in calibration problems, then structural analysis techniques may be most appropriate. Finally, if the problem is one of describing some geographic trajectory, then LNS is most appropriate.

Comparison of glue-line quality between gang edging and straight-line ripping

Treesearch

Charles J. Gatchell; James R. Olson; James R. Olson

1986-01-01

Gang edging with a dip-chain fed gang ripsaw produces gluing surfaces equal to those from a straight-line ripsaw in yellow-poplar (Liriodendron tulipifera) and red oak (Quercus rubra). Special care in gluing red oak was needed to get shear strengths equal to solid wood values. However, the strength comparisons between sawing methods showed no differences between gang...

26 CFR 1.57-0 - Scope.

Code of Federal Regulations, 2010 CFR

2010-04-01

... items of tax preference are: (a) Excess investment interest, (b) The excess of accelerated depreciation on section 1250 property over straight line depreciation, (c) The excess of accelerated depreciation on section 1245 property subject to a net lease over straight line depreciation, (d) The excess of...

5 CFR 532.241 - Analysis of usable wage survey data.

Code of Federal Regulations, 2014 CFR

2014-01-01

... the straight-line, least squares regression formula: Y=a+bx, where Y is the hourly rate, x is grade, a... least 10 unweighed matches and for each nonappropriated fund job having at least 5 unweighed matches...

5 CFR 532.241 - Analysis of usable wage survey data.

Code of Federal Regulations, 2013 CFR

2013-01-01

... the straight-line, least squares regression formula: Y=a+bx, where Y is the hourly rate, x is grade, a... least 10 unweighed matches and for each nonappropriated fund job having at least 5 unweighed matches...

5 CFR 532.241 - Analysis of usable wage survey data.

Code of Federal Regulations, 2012 CFR

2012-01-01

... the straight-line, least squares regression formula: Y=a+bx, where Y is the hourly rate, x is grade, a... least 10 unweighed matches and for each nonappropriated fund job having at least 5 unweighed matches...

5 CFR 532.241 - Analysis of usable wage survey data.

Code of Federal Regulations, 2011 CFR

2011-01-01

... the straight-line, least squares regression formula: Y=a+bx, where Y is the hourly rate, x is grade, a... least 10 unweighed matches and for each nonappropriated fund job having at least 5 unweighed matches...

Automated detection of jet contrails using the AVHRR split window

NASA Technical Reports Server (NTRS)

Engelstad, M.; Sengupta, S. K.; Lee, T.; Welch, R. M.

1992-01-01

This paper investigates the automated detection of jet contrails using data from the Advanced Very High Resolution Radiometer. A preliminary algorithm subtracts the 11.8-micron image from the 10.8-micron image, creating a difference image on which contrails are enhanced. Then a three-stage algorithm searches the difference image for the nearly-straight line segments which characterize contrails. First, the algorithm searches for elevated, linear patterns called 'ridges'. Second, it applies a Hough transform to the detected ridges to locate nearly-straight lines. Third, the algorithm determines which of the nearly-straight lines are likely to be contrails. The paper applies this technique to several test scenes.

International Boundary Study. Series A. Limits in the Seas. Number 42, Straight Baselines: Ecuador.

DTIC Science & Technology

1972-05-23

point a straight line to Puntilla de Santa Elena; (d) A straight line from Puntilla de Santa Elena in the direction of Cabo Blanco ( Peru ) to the...published by the U.S. Navy Oceanographic Office. 1. The seaward extension of the Colombia-Ecuador land boundary into Bahia Ancon de Sardinas is not...Comments 1-2 81 Closes Bahia Ancon de Sardinas, which is neither a historical nor juridical bay, by connecting Cabo Manglares, Colombia (1) and Punta Galera

Gaussian-Beam/Physical-Optics Design Of Beam Waveguide

NASA Technical Reports Server (NTRS)

Veruttipong, Watt; Chen, Jacqueline C.; Bathker, Dan A.

1993-01-01

In iterative method of designing wideband beam-waveguide feed for paraboloidal-reflector antenna, Gaussian-beam approximation alternated with more nearly exact physical-optics analysis of diffraction. Includes curved and straight reflectors guiding radiation from feed horn to subreflector. For iterative design calculations, curved mirrors mathematically modeled as thin lenses. Each distance Li is combined length of two straight-line segments intersecting at one of flat mirrors. Method useful for designing beam-waveguide reflectors or mirrors required to have diameters approximately less than 30 wavelengths at one or more intended operating frequencies.

27 CFR 9.97 - Sonoita.

Code of Federal Regulations, 2010 CFR

2010-04-01

... feet) in the Canelo Hills. (ii) From there in a straight line eastward for approximately 10 miles, to...-northwestward for approximately 21 miles in a straight line to the summit of Granite Peak (7,413 feet) in the... Mount Wrightson (9,543 feet) in the Santa Rita Mountains. (2) Boundary Description—(i) From the starting...

27 CFR 9.97 - Sonoita.

Code of Federal Regulations, 2013 CFR

2013-04-01

... feet) in the Canelo Hills. (ii) From there in a straight line eastward for approximately 10 miles, to...-northwestward for approximately 21 miles in a straight line to the summit of Granite Peak (7,413 feet) in the... Mount Wrightson (9,543 feet) in the Santa Rita Mountains. (2) Boundary Description—(i) From the starting...

27 CFR 9.134 - Oakville.

Code of Federal Regulations, 2014 CFR

2014-04-01

... Highway 29, then continuing in a straight line approximately .1 mile to the peak of the 320+ foot hill... direction in a straight line approximately 1.7 miles along Skellenger Lane, past its intersection with Conn... quadrangle map); (2) Then south along the center of the river bed approximately .4 miles to the point where...

27 CFR 9.97 - Sonoita.

Code of Federal Regulations, 2011 CFR

2011-04-01

... feet) in the Canelo Hills. (ii) From there in a straight line eastward for approximately 10 miles, to...-northwestward for approximately 21 miles in a straight line to the summit of Granite Peak (7,413 feet) in the... Mount Wrightson (9,543 feet) in the Santa Rita Mountains. (2) Boundary Description—(i) From the starting...

27 CFR 9.97 - Sonoita.

Code of Federal Regulations, 2014 CFR

2014-04-01

... feet) in the Canelo Hills. (ii) From there in a straight line eastward for approximately 10 miles, to...-northwestward for approximately 21 miles in a straight line to the summit of Granite Peak (7,413 feet) in the... Mount Wrightson (9,543 feet) in the Santa Rita Mountains. (2) Boundary Description—(i) From the starting...

27 CFR 9.97 - Sonoita.

Code of Federal Regulations, 2012 CFR

2012-04-01

... feet) in the Canelo Hills. (ii) From there in a straight line eastward for approximately 10 miles, to...-northwestward for approximately 21 miles in a straight line to the summit of Granite Peak (7,413 feet) in the... Mount Wrightson (9,543 feet) in the Santa Rita Mountains. (2) Boundary Description—(i) From the starting...

27 CFR 9.134 - Oakville.

Code of Federal Regulations, 2012 CFR

2012-04-01

... Highway 29, then continuing in a straight line approximately .1 mile to the peak of the 320+ foot hill... direction in a straight line approximately 1.7 miles along Skellenger Lane, past its intersection with Conn... quadrangle map); (2) Then south along the center of the river bed approximately .4 miles to the point where...

Pre-School Students' Informal Acquisitions Regarding the Concepts of Point and Straight Line

ERIC Educational Resources Information Center

Orbay, Keziban; Develi, Mehmet Hikmet

2015-01-01

This study aimed to investigate the informal cognitive structures regarding "point" and "straight line"--two basic and undefined terms of geometry--in children registered in preschool--the previous step before in-class formal education process. The study was conducted with the participation of 50 children enrolled in nursery,…

Accurately estimating PSF with straight lines detected by Hough transform

NASA Astrophysics Data System (ADS)

Wang, Ruichen; Xu, Liangpeng; Fan, Chunxiao; Li, Yong

2018-04-01

This paper presents an approach to estimating point spread function (PSF) from low resolution (LR) images. Existing techniques usually rely on accurate detection of ending points of the profile normal to edges. In practice however, it is often a great challenge to accurately localize profiles of edges from a LR image, which hence leads to a poor PSF estimation of the lens taking the LR image. For precisely estimating the PSF, this paper proposes firstly estimating a 1-D PSF kernel with straight lines, and then robustly obtaining the 2-D PSF from the 1-D kernel by least squares techniques and random sample consensus. Canny operator is applied to the LR image for obtaining edges and then Hough transform is utilized to extract straight lines of all orientations. Estimating 1-D PSF kernel with straight lines effectively alleviates the influence of the inaccurate edge detection on PSF estimation. The proposed method is investigated on both natural and synthetic images for estimating PSF. Experimental results show that the proposed method outperforms the state-ofthe- art and does not rely on accurate edge detection.

Optimal approaches for inline sampling of organisms in ballast water: L-shaped vs. Straight sample probes

NASA Astrophysics Data System (ADS)

Wier, Timothy P.; Moser, Cameron S.; Grant, Jonathan F.; Riley, Scott C.; Robbins-Wamsley, Stephanie H.; First, Matthew R.; Drake, Lisa A.

2017-10-01

Both L-shaped ("L") and straight ("Straight") sample probes have been used to collect water samples from a main ballast line in land-based or shipboard verification testing of ballast water management systems (BWMS). A series of experiments was conducted to quantify and compare the sampling efficiencies of L and Straight sample probes. The findings from this research-that both L and Straight probes sample organisms with similar efficiencies-permit increased flexibility for positioning sample probes aboard ships.

The FFAG return loop for the CBETA Energy Recovery Linac

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berg, J. S.

2017-04-28

The CBETA energy recovery linac uses a single xed eld alternating gradient (FFAG) beam line to return the beam for electron beams with four energies, ranging from 42 MeV to 150 MeV. To keep the beam line compact, the ends of the return line have a small radius of curvature, but the central part of the return line is straight. These are connected by transition lines that adiabatically change from one to the other. We rst describe the design or the arc cell. We then describe how a straight cell is created to be a good match to this arcmore » cell. We then describe the design of the transition line between them. The design process makes use of eld maps for the desired magnets. Because we switch magnet types as we move from the arc, through the transition, and into the straight, there are discrete jumps in the elds that degrade the adiabaticity of the transition, and we describe corrections to manage that.« less

Feature-based registration of historical aerial images by Area Minimization

NASA Astrophysics Data System (ADS)

Nagarajan, Sudhagar; Schenk, Toni

2016-06-01

The registration of historical images plays a significant role in assessing changes in land topography over time. By comparing historical aerial images with recent data, geometric changes that have taken place over the years can be quantified. However, the lack of ground control information and precise camera parameters has limited scientists' ability to reliably incorporate historical images into change detection studies. Other limitations include the methods of determining identical points between recent and historical images, which has proven to be a cumbersome task due to continuous land cover changes. Our research demonstrates a method of registering historical images using Time Invariant Line (TIL) features. TIL features are different representations of the same line features in multi-temporal data without explicit point-to-point or straight line-to-straight line correspondence. We successfully determined the exterior orientation of historical images by minimizing the area formed between corresponding TIL features in recent and historical images. We then tested the feasibility of the approach with synthetic and real data and analyzed the results. Based on our analysis, this method shows promise for long-term 3D change detection studies.

27 CFR 9.56 - San Lucas.

Code of Federal Regulations, 2014 CFR

2014-04-01

... mile to the 630-foot promontory in section 32, T. 20 S., R. 9 E.; (1) Then east southeasterly in a straight line approximately 0.6 mile to the 499-foot promontory in the southwest corner of section 33, T. 20 S., R. 9 E.; (2) Then east southeasterly in a straight line approximately 1.3 miles to the 847...

27 CFR 9.30 - North Coast.

Code of Federal Regulations, 2012 CFR

2012-04-01

... Valley Ford; (2) Then southeast in a straight line for approximately 22.0 miles to the peak of Barnabe Mountain (elevation 1466 feet); (3) Then southeast in a straight line for approximately 10.0 miles to the... approximately 5.8 miles to the confluence of San Rafael Creek and San Rafael Bay in San Rafael; (5) Then north...

27 CFR 9.56 - San Lucas.

Code of Federal Regulations, 2011 CFR

2011-04-01

... mile to the 630-foot promontory in section 32, T. 20 S., R. 9 E.; (1) Then east southeasterly in a straight line approximately 0.6 mile to the 499-foot promontory in the southwest corner of section 33, T. 20 S., R. 9 E.; (2) Then east southeasterly in a straight line approximately 1.3 miles to the 847...

27 CFR 9.56 - San Lucas.

Code of Federal Regulations, 2010 CFR

2010-04-01

... mile to the 630-foot promontory in section 32, T. 20 S., R. 9 E.; (1) Then east southeasterly in a straight line approximately 0.6 mile to the 499-foot promontory in the southwest corner of section 33, T. 20 S., R. 9 E.; (2) Then east southeasterly in a straight line approximately 1.3 miles to the 847...

27 CFR 9.178 - Columbia Gorge.

Code of Federal Regulations, 2013 CFR

2013-04-01

... Columbia River. From this point, the boundary line— (1) Goes 1.5 miles straight north along the R9E-R10E line to the northwest corner of section 19, T3N, R10E (Hood River Quadrangle); (2) Continues 2 miles... Quadrangle); (3) Goes 4.1 miles straight north along the section line, crossing onto the Northwestern Lake...

27 CFR 9.178 - Columbia Gorge.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Columbia River. From this point, the boundary line— (1) Goes 1.5 miles straight north along the R9E-R10E line to the northwest corner of section 19, T3N, R10E (Hood River Quadrangle); (2) Continues 2 miles... Quadrangle); (3) Goes 4.1 miles straight north along the section line, crossing onto the Northwestern Lake...

27 CFR 9.178 - Columbia Gorge.

Code of Federal Regulations, 2014 CFR

2014-04-01

... Columbia River. From this point, the boundary line— (1) Goes 1.5 miles straight north along the R9E-R10E line to the northwest corner of section 19, T3N, R10E (Hood River Quadrangle); (2) Continues 2 miles... Quadrangle); (3) Goes 4.1 miles straight north along the section line, crossing onto the Northwestern Lake...

27 CFR 9.30 - North Coast.

Code of Federal Regulations, 2013 CFR

2013-04-01

... Valley Ford; (2) Then southeast in a straight line for approximately 22.0 miles to the peak of Barnabe Mountain (elevation 1466 feet); (3) Then southeast in a straight line for approximately 10.0 miles to the... approximately 5.8 miles to the confluence of San Rafael Creek and San Rafael Bay in San Rafael; (5) Then north...

27 CFR 9.30 - North Coast.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Valley Ford; (2) Then southeast in a straight line for approximately 22.0 miles to the peak of Barnabe Mountain (elevation 1466 feet); (3) Then southeast in a straight line for approximately 10.0 miles to the... approximately 5.8 miles to the confluence of San Rafael Creek and San Rafael Bay in San Rafael; (5) Then north...

27 CFR 9.178 - Columbia Gorge.

Code of Federal Regulations, 2012 CFR

2012-04-01

... Columbia River. From this point, the boundary line— (1) Goes 1.5 miles straight north along the R9E-R10E line to the northwest corner of section 19, T3N, R10E (Hood River Quadrangle); (2) Continues 2 miles... Quadrangle); (3) Goes 4.1 miles straight north along the section line, crossing onto the Northwestern Lake...

27 CFR 9.226 - Inwood Valley.

Code of Federal Regulations, 2014 CFR

2014-04-01

... east-northeasterly in a straight line approximately 4.1 miles, onto the Inwood map, to the 1,786-foot... 2.1 miles to the 2,086-foot elevation point, section 15, T31N/R1W; then (3) Proceed north-northeasterly in a straight line approximately 0.7 mile to the marked 1,648-foot elevation point (which should...

27 CFR 9.56 - San Lucas.

Code of Federal Regulations, 2012 CFR

2012-04-01

... mile to the 630-foot promontory in section 32, T. 20 S., R. 9 E.; (1) Then east southeasterly in a straight line approximately 0.6 mile to the 499-foot promontory in the southwest corner of section 33, T. 20 S., R. 9 E.; (2) Then east southeasterly in a straight line approximately 1.3 miles to the 847...

27 CFR 9.30 - North Coast.

Code of Federal Regulations, 2014 CFR

2014-04-01

... Valley Ford; (2) Then southeast in a straight line for approximately 22.0 miles to the peak of Barnabe Mountain (elevation 1466 feet); (3) Then southeast in a straight line for approximately 10.0 miles to the... approximately 5.8 miles to the confluence of San Rafael Creek and San Rafael Bay in San Rafael; (5) Then north...

27 CFR 9.56 - San Lucas.

Code of Federal Regulations, 2013 CFR

2013-04-01

... mile to the 630-foot promontory in section 32, T. 20 S., R. 9 E.; (1) Then east southeasterly in a straight line approximately 0.6 mile to the 499-foot promontory in the southwest corner of section 33, T. 20 S., R. 9 E.; (2) Then east southeasterly in a straight line approximately 1.3 miles to the 847...

27 CFR 9.30 - North Coast.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Valley Ford; (2) Then southeast in a straight line for approximately 22.0 miles to the peak of Barnabe Mountain (elevation 1466 feet); (3) Then southeast in a straight line for approximately 10.0 miles to the... approximately 5.8 miles to the confluence of San Rafael Creek and San Rafael Bay in San Rafael; (5) Then north...

27 CFR 9.140 - Atlas Peak.

Code of Federal Regulations, 2014 CFR

2014-04-01

... straight line approximately one mile to an unnamed pass with an elevation of 1485 feet, located on Soda Canyon Road; (3) Then easterly in a straight line approximately 0.5 miles to an unnamed peak of 2135 feet... miles to the highest point of an unnamed peak of 1268 feet elevation in section 12, T. 6 N., R. 4 W. on...

27 CFR 9.226 - Inwood Valley.

Code of Federal Regulations, 2013 CFR

2013-04-01

... east-northeasterly in a straight line approximately 4.1 miles, onto the Inwood map, to the 1,786-foot... 2.1 miles to the 2,086-foot elevation point, section 15, T31N/R1W; then (3) Proceed north-northeasterly in a straight line approximately 0.7 mile to the marked 1,648-foot elevation point (which should...

27 CFR 9.140 - Atlas Peak.

Code of Federal Regulations, 2011 CFR

2011-04-01

... straight line approximately one mile to an unnamed pass with an elevation of 1485 feet, located on Soda Canyon Road; (3) Then easterly in a straight line approximately 0.5 miles to an unnamed peak of 2135 feet... miles to the highest point of an unnamed peak of 1268 feet elevation in section 12, T. 6 N., R. 4 W. on...

27 CFR 9.140 - Atlas Peak.

Code of Federal Regulations, 2012 CFR

2012-04-01

... straight line approximately one mile to an unnamed pass with an elevation of 1485 feet, located on Soda Canyon Road; (3) Then easterly in a straight line approximately 0.5 miles to an unnamed peak of 2135 feet... miles to the highest point of an unnamed peak of 1268 feet elevation in section 12, T. 6 N., R. 4 W. on...

27 CFR 9.140 - Atlas Peak.

Code of Federal Regulations, 2013 CFR

2013-04-01

... straight line approximately one mile to an unnamed pass with an elevation of 1485 feet, located on Soda Canyon Road; (3) Then easterly in a straight line approximately 0.5 miles to an unnamed peak of 2135 feet... miles to the highest point of an unnamed peak of 1268 feet elevation in section 12, T. 6 N., R. 4 W. on...

Neck Muscle Moment Arms Obtained In-Vivo from MRI: Effect of Curved and Straight Modeled Paths.

PubMed

Suderman, Bethany L; Vasavada, Anita N

2017-08-01

Musculoskeletal models of the cervical spine commonly represent neck muscles with straight paths. However, straight lines do not best represent the natural curvature of muscle paths in the neck, because the paths are constrained by bone and soft tissue. The purpose of this study was to estimate moment arms of curved and straight neck muscle paths using different moment arm calculation methods: tendon excursion, geometric, and effective torque. Curved and straight muscle paths were defined for two subject-specific cervical spine models derived from in vivo magnetic resonance images (MRI). Modeling neck muscle paths with curvature provides significantly different moment arm estimates than straight paths for 10 of 15 neck muscles (p < 0.05, repeated measures two-way ANOVA). Moment arm estimates were also found to be significantly different among moment arm calculation methods for 11 of 15 neck muscles (p < 0.05, repeated measures two-way ANOVA). In particular, using straight lines to model muscle paths can lead to overestimating neck extension moment. However, moment arm methods for curved paths should be investigated further, as different methods of calculating moment arm can provide different estimates.

Straight-run vs. sex separate rearing for two broiler genetic lines Part 2: Economic analysis and processing advantages.

PubMed

Da Costa, M J; Colson, G; Frost, T J; Halley, J; Pesti, G M

2017-07-01

The objective of this analysis was to evaluate the effects of raising broilers under sex separate and straight-run conditions for 2 broiler genetic lines. One-day-old Ross 308 and Ross 708 chicks (n = 1,344) were sex separated and placed in 48 pens according to rearing type: sex separate (28 males or 28 females) or straight-run (14 males + 14 females). There were 3 dietary phases: starter (zero to 17 d), grower (17 to 32 d), and finisher (32 to 48 d). Bird individual BW and group feed intakes were measured at 12, 17, 25, 32, 42, and 48 d to evaluate performance. At 33, 43, and 49 d 4 birds per pen (straight-run pens 2 males + 2 females) were sampled for carcass yield evaluation. Data were analyzed using linear and non-linear regression in order to estimate feed intake and cut-up weights at 3 separate market weights (1,700, 2,700, and 3,700 g). Returns over feed cost were estimated for a 1.8 million broiler complex for each rearing system and under 9 feed/meat price scenarios. Overall, rearing birds that were sex separated resulted in extra income that ranged from ${\\$}$48,824 to ${\\$}$330,300 per week, depending on the market targeted and feed and meat price scenarios. Sex separation was shown to be especially important in disadvantageous scenarios in which feed prices were high. Gains from sex separation were markedly higher for the Ross 708 than for the Ross 308 broilers. Bird variability also was evaluated at the 3 separate market ages under narrow ranges of BW that were targeted. Straight-run birds decreased the number of birds present in the desired range. Depending on market weight, straight-run rearing resulted in 9.1 to 16.6% fewer birds than sex separate rearing to meet marketing goals. It was concluded that sex separation can result in increased company profitability and have possible beneficial effects at the processing plant due to increased bird uniformity. © 2017 Poultry Science Association Inc.

Power spectrum weighted edge analysis for straight edge detection in images

NASA Astrophysics Data System (ADS)

Karvir, Hrishikesh V.; Skipper, Julie A.

2007-04-01

Most man-made objects provide characteristic straight line edges and, therefore, edge extraction is a commonly used target detection tool. However, noisy images often yield broken edges that lead to missed detections, and extraneous edges that may contribute to false target detections. We present a sliding-block approach for target detection using weighted power spectral analysis. In general, straight line edges appearing at a given frequency are represented as a peak in the Fourier domain at a radius corresponding to that frequency, and a direction corresponding to the orientation of the edges in the spatial domain. Knowing the edge width and spacing between the edges, a band-pass filter is designed to extract the Fourier peaks corresponding to the target edges and suppress image noise. These peaks are then detected by amplitude thresholding. The frequency band width and the subsequent spatial filter mask size are variable parameters to facilitate detection of target objects of different sizes under known imaging geometries. Many military objects, such as trucks, tanks and missile launchers, produce definite signatures with parallel lines and the algorithm proves to be ideal for detecting such objects. Moreover, shadow-casting objects generally provide sharp edges and are readily detected. The block operation procedure offers advantages of significant reduction in noise influence, improved edge detection, faster processing speed and versatility to detect diverse objects of different sizes in the image. With Scud missile launcher replicas as target objects, the method has been successfully tested on terrain board test images under different backgrounds, illumination and imaging geometries with cameras of differing spatial resolution and bit-depth.

Setting the Record Straight. The Truth About Fad Diets.

ERIC Educational Resources Information Center

Wheat Foods Council, Parker, CO.

The Setting the Record Straight information packet presents facts to set the record straight about nutrition and debunk fad diets. The kit features materials designed to communicate the importance of balanced eating. Materials include: a time line of fad diets; four reproducible fad diet book review handouts that show the misleading claims rampant…

Gyrokinetic continuum simulation of turbulence in a straight open-field-line plasma

DOE PAGES

Shi, E. L.; Hammett, G. W.; Stoltzfus-Dueck, T.; ...

2017-05-29

Here, five-dimensional gyrokinetic continuum simulations of electrostatic plasma turbulence in a straight, open-field-line geometry have been performed using a full- discontinuous-Galerkin approach implemented in the Gkeyll code. While various simplifications have been used for now, such as long-wavelength approximations in the gyrokinetic Poisson equation and the Hamiltonian, these simulations include the basic elements of a fusion-device scrape-off layer: localised sources to model plasma outflow from the core, cross-field turbulent transport, parallel flow along magnetic field lines, and parallel losses at the limiter or divertor with sheath-model boundary conditions. The set of sheath-model boundary conditions used in the model allows currentsmore » to flow through the walls. In addition to details of the numerical approach, results from numerical simulations of turbulence in the Large Plasma Device, a linear device featuring straight magnetic field lines, are presented.« less

Optical device fabrication using femtosecond laser processing with glass-hologram

NASA Astrophysics Data System (ADS)

Suzuki, Jun'ichi; Arima, Yasunori; Tanaka, Shuhei

2011-03-01

Using femtosecond laser processing with glass-hologram, fabrication of 1cm-long straight waveguide and X-coupler is reported in this paper. We design and fabricate 4-level glass-hologram which generates 1cm-long straight line intensity. We fabricate 1cm-long waveguides inside fused silica at one shot exposure with the glass-hologram. We investigate the waveguide performance of near field pattern and propagation loss at wavelength of 1550nm. The near field pattern is almost circular shape. The propagation loss at 1550nm is estimated to be < 1.0 dB/cm. As an example of an optical device consisting of straight waveguides, we fabricate X-coupler or 2x2 coupler using straight line waveguides, and observe the output power ratio depending on crossing angle.

Practical Repair Method for Unilateral Cleft Lips: Straight-Line Advanced Release Technique.

PubMed

Baek, Rong-Min; Choi, Jun-Ho; Kim, Baek-Kyu

2016-04-01

Straight-line closure repair of unilateral cleft lips was first introduced in the 1840s, and since then, many different techniques have been attempted for cleft repair. However, these methods have several disadvantages and are difficult to adopt. In this study, we describe our novel technique, known as Straight-Line Advanced Release Technique (StART), and its application in treating several cases of unilateral cleft lip. The preoperative design of the surgical method is drawn on the skin, the vermilion, and the oral mucosa. A total of 13 points are marked (points 0-12). The A flap, B flap, triangular flap, M (medial mucosal) flap, and L (lateral mucosal) flap are designed. After completion of the preoperative marking, the wide dissection is performed to separate the orbicularis oris muscle completely from the abnormally inserted bony structure and the enveloped skin-mucosal flap. The freed orbicularis oris muscle is then reconstructed with full width. After all planes of the lip wound are closed, a straight vertical skin suture line is achieved without any unnecessary transverse scar. Unilateral cleft lip repair using StART was conducted in 145 patients between 1993 and 2012. Cases of microform cleft lip were excluded. A total of 21 patients (14%) required a secondary operation on the lip after the first unilateral cheiloplasty. In all patients, satisfactory surgical outcomes were obtained with an indistinct straight-lined scar and a well-aligned lip contour. To acquire a natural and balanced shape in unilateral cleft lip repair, we recommend the novel StART.

Newton's Law: Not so Simple after All

ERIC Educational Resources Information Center

Robertson, William C.; Gallagher, Jeremiah; Miller, William

2004-01-01

One of the most basic concepts related to force and motion is Newton's first law, which essentially states, "An object at rest tends to remain at rest unless acted on by an unbalanced force. An object in motion in a straight line tends to remain in motion in a straight line unless acted upon by an unbalanced force." Judging by the time and space…

Magnetogate: Using an iPhone Magnetometer for Measuring Kinematic Variables

ERIC Educational Resources Information Center

Temiz, Burak Kagan; Yavuz, Ahmet

2016-01-01

This paper presents a method to measure the movement of an object from specific locations on a straight line using an iPhone's magnetometer. In this method, called "magnetogate," an iPhone is placed on a moving object (in this case a toy car) and small neodymium magnets are arranged at equal intervals on one side of a straight line. The…

Collinear Points Problem

ERIC Educational Resources Information Center

Shultz, Harris S.; Shiflett, Ray C.

2008-01-01

Students were asked to find all possible values for A so that the points (1, 2), (5, A), and (A, 7) lie on a straight line. This problem suggests a generalization: Given (x, y), find all values of A so that the points (x, y), (5, A), and (A, 7) lie on a straight line. We find that this question about linear equations must be resolved using the…

Generation of straight-line shifting bright-dark soliton trains with a wide dip in the symmetric center or dark solitons in optical fibers

NASA Astrophysics Data System (ADS)

Zhong, Xianqiong; Yao, Na; Sheng, Jia'nan; Cheng, Ke

2018-02-01

Nonlinear evolutions of dark soliton pulses with initially constant frequency chirps are investigated numerically for different soliton orders and chirp parameters in different dispersion regimes of optical fibers. The results show interestingly that, in the normal dispersion regime, the evolution properties remain unchanged apart from their straight-line shifts of the temporal trajectories compared with the chirp-free case. While in the anomalous dispersion regime, the dark solitons can evolve to bright-dark soliton trains with a wide black soliton in the symmetric center. The longer the distance, the more the pulse number. The larger the soliton order, the more the pulse number at the same distance. Similarly, straight-line shift of the temporal trajectory of the bright-dark soliton trains will also appear. The shifting amount and direction depend on the absolute value and the sign of the chirp parameter, respectively. This result inspires people to generate bright-dark soliton trains by using ordinary passive optical fibers instead of fiber lasers. Besides, this work also provides us an alternative approach to guide the formed solitons or soliton trains to move their temporal trajectories along straight lines.

Semi Inextensional Post Buckling Analysis of Annular Plates,

DTIC Science & Technology

1981-09-01

too. These methods have their advantages in accuracy but suffer from the drawback of being difficult to use for overall design data or for the...The fact that the high postbuckling curve of the plate approaches a straight line was observed eperimentally [81, [10], where the use of the two

Two-dimensional compressible flow in centrifugal compressors with straight blades

NASA Technical Reports Server (NTRS)

Stanitz, John D; Ellis, Gaylord O

1950-01-01

Six numerical examples are presented for steady, two-dimensional, compressible, nonviscous flow in centrifugal compressors with thin straight blades, the center lines of which generate the surface of a right circular cone when rotated about the axis of the compressor. A seventh example is presented for incompressible flow. The solutions were obtained in a region of the compressors, including the impeller tip, that was considered to be unaffected by the diffuser vanes or by the impeller-inlet configuration. Each solution applies to radial and mixed flow compressors with various cone angles but with the same angle between blades on the conic flow surface. The solution also apply to radial and mixed flow turbines with the rotation and the flow direction reversed. The effects of variations in the following parameters were investigated: (1) flow rate, (2) impeller-tip speed, (3) variation of passage height with radius, and (4) angle between blades on conic flow surface. The numerical results are presented in plots of the streamlines and constant Mach number lines. Correlation equations are developed whereby the flow conditions in any impeller with straight blades can be determined (in the region investigated by this analysis) for all operating conditions.

Destruction of Invariant Surfaces and Magnetic Coordinates for Perturbed Magnetic Fields

DOE Office of Scientific and Technical Information (OSTI.GOV)

S.R. Hudson

2003-11-20

Straight-field-line coordinates are constructed for nearly integrable magnetic fields. The coordinates are based on the robust, noble-irrational rotational-transform surfaces, whose existence is determined by an application of Greene's residue criterion. A simple method to locate these surfaces is described. Sequences of surfaces with rotational-transform converging to low order rationals maximize the region of straight-field-line coordinates.

Head and pelvic movement asymmetries at trot in riding horses in training and perceived as free from lameness by the owner

PubMed Central

Egenvall, Agneta; Haubro Andersen, Pia; Pfau, Thilo

2017-01-01

Recent studies evaluating horses in training and considered free from lameness by their owners have identified a large proportion of horses with motion asymmetries. However the prevalence, type and magnitude of asymmetries when trotting in a straight line or on the lunge have not been investigated. The aim of this study was to objectively investigate the presence of motion asymmetries in riding horses in training by identifying the side and quantifying the degree and type (impact, pushoff) of forelimb and hind limb asymmetries found during straight line trot and on the lunge. In a cross-sectional study, vertical head and pelvic movement symmetry was measured in 222 Warmblood type riding horses, all without perceived performance issues and considered free from lameness by their owners. Body-mounted uni-axial accelerometers were used and differences between maximum and minimum head (HDmax, HDmin) and pelvic (PDmax, PDmin) vertical displacement between left and right forelimb and hind limb stances were calculated during straight line trot and on the lunge. Previously reported symmetry thresholds were used. The thresholds for symmetry were exceeded in 161 horses for at least one variable while trotting in a straight line, HDmin (n = 58, mean 14.3 mm, SD 7.1), HDmax (n = 41, mean 12.7 mm, SD 5.5), PDmax (n = 87, mean 6.5 mm, SD 3.10), PDmin (n = 79, mean 5.7 mm, SD 2.1). Contralateral and ipsilateral concurrent forelimb and hind limb asymmetries were detected in 41 and 49 horses, respectively. There was a linear association between the straight line PDmin values and the values on the lunge with the lame limb to the inside of the circle. A large proportion (72.5%) of horses in training which were perceived as free from lameness by their owner showed movement asymmetries above previously reported asymmetry thresholds during straight line trot. It is not known to what extent these asymmetries are related to pain or to mechanical abnormalities. Therefore, one of the most important questions that must be addressed is how objective asymmetry scores can be translated into pain, orthopedic abnormality, or any type of unsoundness. PMID:28441406

Head and pelvic movement asymmetries at trot in riding horses in training and perceived as free from lameness by the owner.

PubMed

Rhodin, Marie; Egenvall, Agneta; Haubro Andersen, Pia; Pfau, Thilo

2017-01-01

Recent studies evaluating horses in training and considered free from lameness by their owners have identified a large proportion of horses with motion asymmetries. However the prevalence, type and magnitude of asymmetries when trotting in a straight line or on the lunge have not been investigated. The aim of this study was to objectively investigate the presence of motion asymmetries in riding horses in training by identifying the side and quantifying the degree and type (impact, pushoff) of forelimb and hind limb asymmetries found during straight line trot and on the lunge. In a cross-sectional study, vertical head and pelvic movement symmetry was measured in 222 Warmblood type riding horses, all without perceived performance issues and considered free from lameness by their owners. Body-mounted uni-axial accelerometers were used and differences between maximum and minimum head (HDmax, HDmin) and pelvic (PDmax, PDmin) vertical displacement between left and right forelimb and hind limb stances were calculated during straight line trot and on the lunge. Previously reported symmetry thresholds were used. The thresholds for symmetry were exceeded in 161 horses for at least one variable while trotting in a straight line, HDmin (n = 58, mean 14.3 mm, SD 7.1), HDmax (n = 41, mean 12.7 mm, SD 5.5), PDmax (n = 87, mean 6.5 mm, SD 3.10), PDmin (n = 79, mean 5.7 mm, SD 2.1). Contralateral and ipsilateral concurrent forelimb and hind limb asymmetries were detected in 41 and 49 horses, respectively. There was a linear association between the straight line PDmin values and the values on the lunge with the lame limb to the inside of the circle. A large proportion (72.5%) of horses in training which were perceived as free from lameness by their owner showed movement asymmetries above previously reported asymmetry thresholds during straight line trot. It is not known to what extent these asymmetries are related to pain or to mechanical abnormalities. Therefore, one of the most important questions that must be addressed is how objective asymmetry scores can be translated into pain, orthopedic abnormality, or any type of unsoundness.

Straight scaling FFAG beam line

NASA Astrophysics Data System (ADS)

Lagrange, J.-B.; Planche, T.; Yamakawa, E.; Uesugi, T.; Ishi, Y.; Kuriyama, Y.; Qin, B.; Okabe, K.; Mori, Y.

2012-11-01

Fixed field alternating gradient (FFAG) accelerators are recently subject to a strong revival. They are usually designed in a circular shape; however, it would be an asset to guide particles with no overall bend in this type of accelerator. An analytical development of a straight FFAG cell which keeps zero-chromaticity is presented here. A magnetic field law is thus obtained, called "straight scaling law", and an experiment has been conducted to confirm this zero-chromatic law. A straight scaling FFAG prototype has been designed and manufactured, and horizontal phase advances of two different energies are measured. Results are analyzed to clarify the straight scaling law.

Extrapolation of Functions of Many Variables by Means of Metric Analysis

NASA Astrophysics Data System (ADS)

Kryanev, Alexandr; Ivanov, Victor; Romanova, Anastasiya; Sevastianov, Leonid; Udumyan, David

2018-02-01

The paper considers a problem of extrapolating functions of several variables. It is assumed that the values of the function of m variables at a finite number of points in some domain D of the m-dimensional space are given. It is required to restore the value of the function at points outside the domain D. The paper proposes a fundamentally new method for functions of several variables extrapolation. In the presented paper, the method of extrapolating a function of many variables developed by us uses the interpolation scheme of metric analysis. To solve the extrapolation problem, a scheme based on metric analysis methods is proposed. This scheme consists of two stages. In the first stage, using the metric analysis, the function is interpolated to the points of the domain D belonging to the segment of the straight line connecting the center of the domain D with the point M, in which it is necessary to restore the value of the function. In the second stage, based on the auto regression model and metric analysis, the function values are predicted along the above straight-line segment beyond the domain D up to the point M. The presented numerical example demonstrates the efficiency of the method under consideration.

On the barn owl's visual pre-attack behavior: I. Structure of head movements and motion patterns.

PubMed

Ohayon, Shay; van der Willigen, Robert F; Wagner, Hermann; Katsman, Igor; Rivlin, Ehud

2006-09-01

Barn owls exhibit a rich repertoire of head movements before taking off for prey capture. These movements occur mainly at light levels that allow for the visual detection of prey. To investigate these movements and their functional relevance, we filmed the pre-attack behavior of barn owls. Off-line image analysis enabled reconstruction of all six degrees of freedom of head movements. Three categories of head movements were observed: fixations, head translations and head rotations. The observed rotations contained a translational component. Head rotations did not follow Listing's law, but could be well described by a second-order surface, which indicated that they are in close agreement with Donder's law. Head translations did not contain any significant rotational components. Translations were further segmented into straight-line and curved paths. Translations along an axis perpendicular to the line of sight were similar to peering movements observed in other animals. We suggest that these basic motion elements (fixations, head rotations, translations along a straight line, and translation along a curved trajectory) may be combined to form longer and more complex behavior. We speculate that these head movements mainly underlie estimation of distance during prey capture.

7 CFR 1786.153 - Discounted present value.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 2 1-year. 2 3 2-year. 3 4 3-year. 4 5 (1) 5 6 5-year. 6 7 (2) 7 8 7-year. 8 9 (3) 9 10 (3) 10 11 10... Maturities computed as above. 3 A straight line interpolated rate between the 7-year rate and the 10-year rate. (See formula below) 4 A straight line interpolated rate between the 10-year note and the 20-year...

7 CFR 1786.153 - Discounted present value.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 2 1-year. 2 3 2-year. 3 4 3-year. 4 5 (1) 5 6 5-year. 6 7 (2) 7 8 7-year. 8 9 (3) 9 10 (3) 10 11 10... Maturities computed as above. 3 A straight line interpolated rate between the 7-year rate and the 10-year rate. (See formula below) 4 A straight line interpolated rate between the 10-year note and the 20-year...

Parallel Hough Transform-Based Straight Line Detection and Its FPGA Implementation in Embedded Vision

PubMed Central

Lu, Xiaofeng; Song, Li; Shen, Sumin; He, Kang; Yu, Songyu; Ling, Nam

2013-01-01

Hough Transform has been widely used for straight line detection in low-definition and still images, but it suffers from execution time and resource requirements. Field Programmable Gate Arrays (FPGA) provide a competitive alternative for hardware acceleration to reap tremendous computing performance. In this paper, we propose a novel parallel Hough Transform (PHT) and FPGA architecture-associated framework for real-time straight line detection in high-definition videos. A resource-optimized Canny edge detection method with enhanced non-maximum suppression conditions is presented to suppress most possible false edges and obtain more accurate candidate edge pixels for subsequent accelerated computation. Then, a novel PHT algorithm exploiting spatial angle-level parallelism is proposed to upgrade computational accuracy by improving the minimum computational step. Moreover, the FPGA based multi-level pipelined PHT architecture optimized by spatial parallelism ensures real-time computation for 1,024 × 768 resolution videos without any off-chip memory consumption. This framework is evaluated on ALTERA DE2-115 FPGA evaluation platform at a maximum frequency of 200 MHz, and it can calculate straight line parameters in 15.59 ms on the average for one frame. Qualitative and quantitative evaluation results have validated the system performance regarding data throughput, memory bandwidth, resource, speed and robustness. PMID:23867746

Parallel Hough Transform-based straight line detection and its FPGA implementation in embedded vision.

PubMed

Lu, Xiaofeng; Song, Li; Shen, Sumin; He, Kang; Yu, Songyu; Ling, Nam

2013-07-17

Hough Transform has been widely used for straight line detection in low-definition and still images, but it suffers from execution time and resource requirements. Field Programmable Gate Arrays (FPGA) provide a competitive alternative for hardware acceleration to reap tremendous computing performance. In this paper, we propose a novel parallel Hough Transform (PHT) and FPGA architecture-associated framework for real-time straight line detection in high-definition videos. A resource-optimized Canny edge detection method with enhanced non-maximum suppression conditions is presented to suppress most possible false edges and obtain more accurate candidate edge pixels for subsequent accelerated computation. Then, a novel PHT algorithm exploiting spatial angle-level parallelism is proposed to upgrade computational accuracy by improving the minimum computational step. Moreover, the FPGA based multi-level pipelined PHT architecture optimized by spatial parallelism ensures real-time computation for 1,024 × 768 resolution videos without any off-chip memory consumption. This framework is evaluated on ALTERA DE2-115 FPGA evaluation platform at a maximum frequency of 200 MHz, and it can calculate straight line parameters in 15.59 ms on the average for one frame. Qualitative and quantitative evaluation results have validated the system performance regarding data throughput, memory bandwidth, resource, speed and robustness.

A Closed-Form Error Model of Straight Lines for Improved Data Association and Sensor Fusing

PubMed Central

2018-01-01

Linear regression is a basic tool in mobile robotics, since it enables accurate estimation of straight lines from range-bearing scans or in digital images, which is a prerequisite for reliable data association and sensor fusing in the context of feature-based SLAM. This paper discusses, extends and compares existing algorithms for line fitting applicable also in the case of strong covariances between the coordinates at each single data point, which must not be neglected if range-bearing sensors are used. Besides, in particular, the determination of the covariance matrix is considered, which is required for stochastic modeling. The main contribution is a new error model of straight lines in closed form for calculating quickly and reliably the covariance matrix dependent on just a few comprehensible and easily-obtainable parameters. The model can be applied widely in any case when a line is fitted from a number of distinct points also without a priori knowledge of the specific measurement noise. By means of extensive simulations, the performance and robustness of the new model in comparison to existing approaches is shown. PMID:29673205

40 CFR Appendix A to Subpart E of... - Cost-Effectiveness Analysis Guidelines

Code of Federal Regulations, 2011 CFR

2011-07-01

... of the resources which are attributable to the waste treatment management system or to one of its... end of the planning period. In this case, salvage value shall be estimated using straight line..., commercial and institutional sources, shall be based upon one of the following methods: (a) Preferred method...

40 CFR Appendix A to Subpart E of... - Cost-Effectiveness Analysis Guidelines

Code of Federal Regulations, 2012 CFR

2012-07-01

... of the resources which are attributable to the waste treatment management system or to one of its... end of the planning period. In this case, salvage value shall be estimated using straight line..., commercial and institutional sources, shall be based upon one of the following methods: (a) Preferred method...

40 CFR Appendix A to Subpart E of... - Cost-Effectiveness Analysis Guidelines

Code of Federal Regulations, 2010 CFR

2010-07-01

... of the resources which are attributable to the waste treatment management system or to one of its... end of the planning period. In this case, salvage value shall be estimated using straight line..., commercial and institutional sources, shall be based upon one of the following methods: (a) Preferred method...

40 CFR Appendix A to Subpart E of... - Cost-Effectiveness Analysis Guidelines

Code of Federal Regulations, 2013 CFR

2013-07-01

... of the resources which are attributable to the waste treatment management system or to one of its... end of the planning period. In this case, salvage value shall be estimated using straight line..., commercial and institutional sources, shall be based upon one of the following methods: (a) Preferred method...

40 CFR Appendix A to Subpart E of... - Cost-Effectiveness Analysis Guidelines

Code of Federal Regulations, 2014 CFR

2014-07-01

... of the resources which are attributable to the waste treatment management system or to one of its... end of the planning period. In this case, salvage value shall be estimated using straight line..., commercial and institutional sources, shall be based upon one of the following methods: (a) Preferred method...

Fins improve the swimming performance of fish sperm: a hydrodynamic analysis of the Siberian sturgeon Acipenser baerii.

PubMed

Gillies, Eric A; Bondarenko, Volodymyr; Cosson, Jacky; Pacey, Allan A

2013-02-01

The flagella of sturgeon sperm have an ultrastructure comprising paddle-like fins extending along most of their length. These fins are seen in several other marine and freshwater fish. The sperm of these fish are fast swimmers and are relatively short lived: it is therefore tempting to think of these fins as having evolved for hydrodynamic advantage, but the actual advantage they impart, at such a small length scale and slow speed, is unclear. The phrase "the fins improve hydrodynamic efficiency" is commonly found in biological literature, yet little hydrodynamic analysis has previously been used to support such conjectures. In this paper, we examine various hydrodynamic models of sturgeon sperm and investigate both swimming velocity and energy expenditure. All of the models indicate a modest hydrodynamic advantage of finned sperm, in both straight line swimming speed and a hydrodynamic efficiency measure. We find a hydrodynamic advantage for a flagellum with fins, over one without fins, of the order of 15-20% in straight line propulsive velocity and 10-15% in a hydrodynamic efficiency measure. Copyright © 2012 Wiley Periodicals, Inc.

Wave Breaking Induced Surface Wakes and Jets Observed during a Bora Event

DTIC Science & Technology

2005-01-01

terrain contours (interval = 200 m) superposed. The approximate NCAR Electra and NOAA P-3 flight tracks are indicated by bold and dotted straight lines ...Hz data. The red curves correspond to the COAMPS simulated fields obtained by interpolating the 1-km grid data to the straight line through the...Alpine Experiment (ALPEX) in 1982 [Smith, 1987]. These studies suggested that the bora flow shares some common characteristics with downslope windstorms

Strategic Embodiment in Virtual Spaces: Exploring an On-Line Discussion about Sexualities Equality in Schools

ERIC Educational Resources Information Center

Depalma, Renee; Atkinson, Elizabeth

2007-01-01

This paper analyses patterns of participation on a voluntary anonymous Web-based discussion forum, open to students and faculty in one UK university, concerning sexualities equality in schools. Analysis revealed that participants often rejected the security of anonymity and strategically embodied themselves and others (as gay, straight, parents,…

Beyond Line of Sight (BLOS) Command and Control (C2) Capability to Improve Disaster Response and Recovery

DTIC Science & Technology

2013-09-01

on the possible threat of an electromagnetic pulse (EMP) and its potential consequences following the destructive “ derecho ” that hit Washington, DC...in 2012.19 Spanish for the word “straight,” a derecho is a term used to describe a widespread, long- lived, straight-line windstorm that is...emergency communications system and raised concern for future response. Both Hurricane Katrina and the Washington, DC, area derecho have subsequently

Activity Demands During Multi-Directional Team Sports: A Systematic Review.

PubMed

Taylor, Jeffrey B; Wright, Alexis A; Dischiavi, Steven L; Townsend, M Allison; Marmon, Adam R

2017-12-01

Late-stage rehabilitation programs often incorporate 'sport-specific' demands, but may not optimally simulate the in-game volume or intensity of such activities as sprinting, cutting, jumping, and lateral movement. The aim of this review was to characterize, quantify, and compare straight-line running and multi-directional demands during sport competition. A systematic review of PubMed, CINAHL, SPORTDiscus, and Cochrane Central Register of Controlled Trials databases was conducted. Studies that reported time-motion analysis data on straight-line running, accelerations/decelerations, activity changes, jumping, cutting, or lateral movement over the course of an entire competition in a multi-directional sport (soccer, basketball, lacrosse, handball, field hockey, futsal, volleyball) were included. Data was organized based on sport, age level, and sex and descriptive statistics of the frequency, intensity, time, and volume of the characteristics of running and multi-directional demands were extracted from each study. Eighty-one studies were included in the review (n = 47 soccer, n = 11 basketball, n = 9 handball, n = 7 field hockey, n = 3 futsal, n = 4 volleyball). Variability of sport demand data was found across sports, sexes, and age levels. Specifically, soccer and field hockey demanded the most volume of running, while basketball required the highest ratio of high-intensity running to sprinting. Athletes change activity between 500 and 3000 times over the course of a competition, or once every 2-4 s. Studies of soccer reported the most frequent cutting (up to 800 per game), while studies of basketball reported the highest frequency of lateral movement (up to 450 per game). Basketball (42-56 per game), handball (up to 90 per game), and volleyball (up to 35 per game) were found to require the most jumping. These data may provide an incomplete view of an athlete's straight-line running load, considering that only competition and not practice data was provided. Considerable variability exists in the demands of straight-line running and multi-directional demands across sports, competition levels, and sexes, indicating the need for sports medicine clinicians to design future rehabilitation programs with improved specificity (including the type of activity and dosage) to these demands.

Exact Performance Analysis of Two Distributed Processes with Multiple Synchronization Points.

DTIC Science & Technology

1987-05-01

number of processes with straight-line sequences of semaphore operations . We use the geometric model for performance analysis, in contrast to proving...distribution unlimited. 4. PERFORMING’*ORGANIZATION REPORT NUMBERS) 5. MONITORING ORGANIZATION REPORT NUMB CS-TR-1845 6a. NAME OF PERFORMING ORGANIZATION 6b...OFFICE SYMBOL 7a. NAME OF MONITORING ORGANIZATIO U University of Maryland (If applicable) Office of Naval Research N/A 6c. ADDRESS (City, State, and

Period Variation in BW Vulpeculae (Abstract)

NASA Astrophysics Data System (ADS)

Cowall, D. E.; Odell, A. P.

2018-06-01

(Abstract only) BW Vulpeculae (BW Vul) has the largest amplitude of the beta Cephei stars. An observing campaign on this star using the AAVSOnetís Bright Star Monitor (BSM) telescopes was begun in December of 2015 and has yielded 66 nights of observations to date. A period analysis will be presented using the BSM data set in combination with unpublished data from the Lowell Observatory. Over almost 80 years of observations, BW Vul has closely followed a parabolic ephemeris (period increasing by 2.4 seconds/century) plus a light-travel-time effect. This parabola with excursions on either side also could be viewed as a sequence of straight lines (constant period) with abrupt period increases. The first paradigm predicted a necessary change in slope around 2004, which did not occur. Instead, the period decreased abruptly in 2009. That maximum occurred 250 minutes early compared to the first paradigm, and about 25 minutes early compared to the straight-line paradigm from 1982ñ2009.

Thinking in a straight line.

PubMed

Chambers, David W

2013-01-01

Rational human discourse is not as common as we imagine or as we would like it to be. Sometimes it is necessary to use fallacies and fabrication to get to the point we favor. This essay is an illustrated list of 33 handy tools for avoiding thinking straight.

Navy Nuclear Aircraft Carrier (CVN) Homeporting at Mayport: Background and Issues for Congress

DTIC Science & Technology

2010-12-09

Release No. 233-09 of April 10, 2009, entitled “Quadrennial Defense Review To Determine Aircraft Carrier Homeporting In Mayport,” available online at...is the straight-line distance between the two locations, as calculated by the “How Fair Is It?” online distance calculator available at http...straight-line distance between the two locations, as calculated by the “How Fair Is It?” online distance calculator available at http://www.indo.com/cgi

Rudiments of curvelet with applications

NASA Astrophysics Data System (ADS)

Zahra, Noor e.

2012-07-01

Curvelet transform is now a days a favored tool for image processing. Edges are an important part of an image and usually they are not straight lines. Curvelet prove to be very efficient in representing curve like edges. In this chapter application of curvelet is shown with some examples like seismic wave analysis, oil exploration, fingerprint identification and biomedical images like mammography and MRI.

Multidirectional Scanning Model, MUSCLE, to Vectorize Raster Images with Straight Lines

PubMed Central

Karas, Ismail Rakip; Bayram, Bulent; Batuk, Fatmagul; Akay, Abdullah Emin; Baz, Ibrahim

2008-01-01

This paper presents a new model, MUSCLE (Multidirectional Scanning for Line Extraction), for automatic vectorization of raster images with straight lines. The algorithm of the model implements the line thinning and the simple neighborhood methods to perform vectorization. The model allows users to define specified criteria which are crucial for acquiring the vectorization process. In this model, various raster images can be vectorized such as township plans, maps, architectural drawings, and machine plans. The algorithm of the model was developed by implementing an appropriate computer programming and tested on a basic application. Results, verified by using two well known vectorization programs (WinTopo and Scan2CAD), indicated that the model can successfully vectorize the specified raster data quickly and accurately. PMID:27879843

Multidirectional Scanning Model, MUSCLE, to Vectorize Raster Images with Straight Lines.

PubMed

Karas, Ismail Rakip; Bayram, Bulent; Batuk, Fatmagul; Akay, Abdullah Emin; Baz, Ibrahim

2008-04-15

This paper presents a new model, MUSCLE (Multidirectional Scanning for Line Extraction), for automatic vectorization of raster images with straight lines. The algorithm of the model implements the line thinning and the simple neighborhood methods to perform vectorization. The model allows users to define specified criteria which are crucial for acquiring the vectorization process. In this model, various raster images can be vectorized such as township plans, maps, architectural drawings, and machine plans. The algorithm of the model was developed by implementing an appropriate computer programming and tested on a basic application. Results, verified by using two well known vectorization programs (WinTopo and Scan2CAD), indicated that the model can successfully vectorize the specified raster data quickly and accurately.

Magnetogate: using an iPhone magnetometer for measuring kinematic variables

NASA Astrophysics Data System (ADS)

Kağan Temiz, Burak; Yavuz, Ahmet

2016-01-01

This paper presents a method to measure the movement of an object from specific locations on a straight line using an iPhone’s magnetometer. In this method, called ‘magnetogate’, an iPhone is placed on a moving object (in this case a toy car) and small neodymium magnets are arranged at equal intervals on one side of a straight line. The magnetometer sensor of the iPhone is switched on and then the car starts moving. The iPhone’s magnetometer is stimulated throughout its movement along a straight line. A ‘sensor Kinetics’ application on the iPhone saves the magnetic stimulations and produces a graph of the changing magnetic field near the iPhone. At the end of motion, data from the magnetometer is interpreted and peaks on the graph are detected. Thus, position-time changes can be analysed and comments about the motion of the object can be made. The position, velocity and acceleration of the object can be easily measured with this method.

Effect of prostatic fluid on the quality of fresh and frozen-thawed canine epididymal spermatozoa.

PubMed

Korochkina, E; Johannisson, A; Goodla, Lavanya; Morrell, J M; Axner, E

2014-12-01

Canine epididymal spermatozoa have a low freeze-tolerance ability compared with ejaculated spermatozoa, which could arise from the absence of prostatic fluid (PF). Therefore, the purpose of this work was to elucidate the influence of PF on the quality of canine epididymal sperm before and after freezing. Caudae epididymides were retrieved from eight dogs after routine castration. Spermatozoa were released by slicing the tissue and were extended in either Tris solution or PF before freezing. Frozen sperm samples were thawed at 70 °C for 8 seconds in a waterbath. Sperm concentration, motility using computer-assisted sperm analysis, morphology, plasma membrane, acrosome and chromatin integrity were assessed in the fresh sperm samples (after 20 minutes incubation) and at 0 and 4 hours after thawing. Progressive motility, distance straight line, distance average path, average path velocity, curvilinear velocity, straight line velocity, straightness, linearity, wobble, and beat cross frequency were significantly increased after extraction into PF. There was a higher proportion of spermatozoa with DNA damage in the PF treatment group at 4 hours after thawing than in the Tris treatment group (15.8% vs. 6.7%, P < 0.05). These results suggest that the addition of PF to canine spermatozoa activates sperm motility in fresh spermatozoa but has a negative effect on chromatin integrity after freezing-thawing. Copyright © 2014 Elsevier Inc. All rights reserved.

Linear Titration Curves of Acids and Bases.

PubMed

Joseph, N R

1959-05-29

The Henderson-Hasselbalch equation, by a simple transformation, becomes pH - pK = pA - pB, where pA and pB are the negative logarithms of acid and base concentrations. Sigmoid titration curves then reduce to straight lines; titration curves of polyelectrolytes, to families of straight lines. The method is applied to the titration of the dipeptide glycyl aminotricarballylic acid, with four titrable groups. Results are expressed as Cartesian and d'Ocagne nomograms. The latter is of a general form applicable to polyelectrolytes of any degree of complexity.

Navy Nuclear Aircraft Carrier (CVN) Homeporting at Mayport: Background and Issues for Congress

DTIC Science & Technology

2012-02-21

Pacific Ocean. The figure of about 32 nautical miles is the straight-line distance between the two locations, as calculated by the “How Far Is It?” online ...itself. 9 This is the straight-line distance between the two locations, as calculated by the “How Far Is It?” online distance calculator, available at...Authorization Act (S. 3001/P.L. 110- 417) Section 2207 of the FY2009 defense authorization bill as passed by the House (H.R. 5658; H.Rept. 110-652 of May

The long-solved problem of the best-fit straight line: application to isotopic mixing lines

NASA Astrophysics Data System (ADS)

Wehr, Richard; Saleska, Scott R.

2017-01-01

It has been almost 50 years since York published an exact and general solution for the best-fit straight line to independent points with normally distributed errors in both x and y. York's solution is highly cited in the geophysical literature but almost unknown outside of it, so that there has been no ebb in the tide of books and papers wrestling with the problem. Much of the post-1969 literature on straight-line fitting has sown confusion not merely by its content but by its very existence. The optimal least-squares fit is already known; the problem is already solved. Here we introduce the non-specialist reader to York's solution and demonstrate its application in the interesting case of the isotopic mixing line, an analytical tool widely used to determine the isotopic signature of trace gas sources for the study of biogeochemical cycles. The most commonly known linear regression methods - ordinary least-squares regression (OLS), geometric mean regression (GMR), and orthogonal distance regression (ODR) - have each been recommended as the best method for fitting isotopic mixing lines. In fact, OLS, GMR, and ODR are all special cases of York's solution that are valid only under particular measurement conditions, and those conditions do not hold in general for isotopic mixing lines. Using Monte Carlo simulations, we quantify the biases in OLS, GMR, and ODR under various conditions and show that York's general - and convenient - solution is always the least biased.

The conformal transformation of an airfoil into a straight line and its application to the inverse problem of airfoil theory

NASA Technical Reports Server (NTRS)

Mutterperl, William

1944-01-01

A method of conformal transformation is developed that maps an airfoil into a straight line, the line being chosen as the extended chord line of the airfoil. The mapping is accomplished by operating directly with the airfoil ordinates. The absence of any preliminary transformation is found to shorten the work substantially over that of previous methods. Use is made of the superposition of solutions to obtain a rigorous counterpart of the approximate methods of thin-airfoils theory. The method is applied to the solution of the direct and inverse problems for arbitrary airfoils and pressure distributions. Numerical examples are given. Applications to more general types of regions, in particular to biplanes and to cascades of airfoils, are indicated. (author)

Apparatus and method for routing a transmission line through a downhole tool

DOEpatents

Hall, David R.; Hall, Jr., H. Tracy; Pixton, David S.; Briscoe, Michael; Reynolds, Jay

2006-07-04

A method for routing a transmission line through a tool joint having a primary and secondary shoulder, a central bore, and a longitudinal axis, includes drilling a straight channel, at a positive, nominal angle with respect to the longitudinal axis, through the tool joint from the secondary shoulder to a point proximate the inside wall of the centtral bore. The method further includes milling back, from within the central bore, a second channel to merge with the straight channel, thereby forming a continuous channel from the secondary shoulder to the central bore. In selected embodiments, drilling is accomplished by gun-drilling the straight channel. In other embodiments, the method includes tilting the tool joint before drilling to produce the positive, nominal angle. In selected embodiments, the positive, nominal angle is less than or equal to 15 degrees.

Straight A's: Public Education Policy and Progress. Volume 12, Number 5

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2012-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) House Committee Passes Education Reform Legislation: On Party-Line Votes, Committee Passes Accountability and Teacher…

Building Bridges One Line at a Time

ERIC Educational Resources Information Center

Grigsby, Cathy Murray

2012-01-01

In this article, first-grade students were taught the different kinds of lines that were part of the construction of various bridges--the curved lines of the arches of stone bridges, straight lines connecting the cables of a suspension bridge, vertical lines, horizontal lines, and so on. They gained practice in drawing structures and in fine brush…

Nonlinear estimation of parameters in biphasic Arrhenius plots.

PubMed

Puterman, M L; Hrboticky, N; Innis, S M

1988-05-01

This paper presents a formal procedure for the statistical analysis of data on the thermotropic behavior of membrane-bound enzymes generated using the Arrhenius equation and compares the analysis to several alternatives. Data is modeled by a bent hyperbola. Nonlinear regression is used to obtain estimates and standard errors of the intersection of line segments, defined as the transition temperature, and slopes, defined as energies of activation of the enzyme reaction. The methodology allows formal tests of the adequacy of a biphasic model rather than either a single straight line or a curvilinear model. Examples on data concerning the thermotropic behavior of pig brain synaptosomal acetylcholinesterase are given. The data support the biphasic temperature dependence of this enzyme. The methodology represents a formal procedure for statistical validation of any biphasic data and allows for calculation of all line parameters with estimates of precision.

[Procedural analysis of acid-base balance disorder: case serials in 4 patents].

PubMed

Ma, Chunyuan; Wang, Guijie

2017-05-01

To establish the standardization process of acid-base balance analysis, analyze cases of acid-base balance disorder with the aid of acid-base balance coordinate graph. The acid-base balance theory were reviewed systematically on recent research progress, and the important concepts, definitions, formulas, parameters, regularity and inference in the analysis of acid-base balance were studied. The analysis of acid-base balance disordered processes and steps were figured. The application of acid-base balance coordinate graph in the cases was introduced. The method of "four parameters-four steps" analysis was put forward to analyze the acid-base balance disorders completely. "Four parameters" included pH, arterial partial pressure of carbon dioxide (PaCO 2 ), HCO 3 - and anion gap (AG). "Four steps" were outlined by following aspects: (1) according to the pH, PaCO 2 and HCO 3 - , the primary or main types of acid-base balance disorder was determined; (2) primary or main types of acid-base disorder were used to choose the appropriate compensation formula and to determine the presence of double mixed acid-base balance disorder; (3) the primary acid-base balance disorders were divided into two parts: respiratory acidosis or respiratory alkalosis, at the same time, the potential HCO 3 - should be calculated, the measured HCO 3 - should be replaced with potential HCO 3 - , to determine whether there were three mixed acid-base disorders; (4) based on the above analysis the data judged as the simple AG increased-metabolic acidosis was needed to be further analyzed. The ratio of ΔAG↑/ΔHCO 3 - ↓ was also needed to be calculated, to determine whether there was normal AG metabolic acidosis or metabolic alkalosis. In the clinical practice, PaCO 2 (as the abscissa) and HCO 3 - (as the ordinate) were used to establish a rectangular coordinate system, through origin (0, 0) and coordinate point (40, 24) could be a straight line, and all points on the straight line pH were equal to 7.40. The acid-base balance coordinate graph could be divided into seven areas by three straight lines [namely pH = 7.40 isoline, PaCO 2 = 40 mmHg (1 mmHg = 0.133 kPa) line and HCO 3 - = 24 mmol/L line]: main respiratory alkalosis area, main metabolic alkalosis area, respiratory + metabolic alkalosis area, main respiratory acidosis area, main metabolic acidosis area, respiratory + metabolic acidosis area and normal area. It was easier to determine the type of acid-base balance disorders by identifying the location of the (PaCO 2 , HCO 3 - ) or (PaCO 2 , potential HCO 3 - ) point on the acid-base balance coordinate graph. "Four parameters-four steps" method is systematic and comprehensive. At the same time, by using the acid-base balance coordinate graph, it is simpler to estimate the types of acid-base balance disorders. It is worthy of popularizing and generalizing.

49 CFR 179.201-3 - Lined tanks.

Code of Federal Regulations, 2011 CFR

2011-10-01

...-Pressure Tank Car Tanks (Classes DOT-111AW and 115AW) § 179.201-3 Lined tanks. (a) Rubber-lined tanks. (1) Each tank or each compartment thereof must be lined with acid-resistant rubber or other approved rubber... double thickness. The rubber lining must overlap at least 11/2 inches at all edges which must be straight...

49 CFR 179.201-3 - Lined tanks.

Code of Federal Regulations, 2012 CFR

2012-10-01

...-Pressure Tank Car Tanks (Classes DOT-111AW and 115AW) § 179.201-3 Lined tanks. (a) Rubber-lined tanks. (1) Each tank or each compartment thereof must be lined with acid-resistant rubber or other approved rubber... double thickness. The rubber lining must overlap at least 11/2 inches at all edges which must be straight...

49 CFR 179.201-3 - Lined tanks.

Code of Federal Regulations, 2013 CFR

2013-10-01

...-Pressure Tank Car Tanks (Classes DOT-111AW and 115AW) § 179.201-3 Lined tanks. (a) Rubber-lined tanks. (1) Each tank or each compartment thereof must be lined with acid-resistant rubber or other approved rubber... double thickness. The rubber lining must overlap at least 11/2 inches at all edges which must be straight...

49 CFR 179.201-3 - Lined tanks.

Code of Federal Regulations, 2014 CFR

2014-10-01

...-Pressure Tank Car Tanks (Classes DOT-111AW and 115AW) § 179.201-3 Lined tanks. (a) Rubber-lined tanks. (1) Each tank or each compartment thereof must be lined with acid-resistant rubber or other approved rubber... double thickness. The rubber lining must overlap at least 11/2 inches at all edges which must be straight...

Minimum-fuel turning climbout and descent guidance of transport jets

NASA Technical Reports Server (NTRS)

Neuman, F.; Kreindler, E.

1983-01-01

The complete flightpath optimization problem for minimum fuel consumption from takeoff to landing including the initial and final turns from and to the runway heading is solved. However, only the initial and final segments which contain the turns are treated, since the straight-line climbout, cruise, and descent problems have already been solved. The paths are derived by generating fields of extremals, using the necessary conditions of optimal control together with singular arcs and state constraints. Results show that the speed profiles for straight flight and turning flight are essentially identical except for the final horizontal accelerating or decelerating turns. The optimal turns require no abrupt maneuvers, and an approximation of the optimal turns could be easily integrated with present straight-line climb-cruise-descent fuel-optimization algorithms. Climbout at the optimal IAS rather than the 250-knot terminal-area speed limit would save 36 lb of fuel for the 727-100 aircraft.

Failure of the straight-line DCS boundary when extrapolated to the hypobaric realm.

PubMed

Conkin, J; Van Liew, H D

1992-11-01

The lowest pressure (P2) to which a diver can ascend without developing decompression sickness (DCS) after becoming equilibrated at some higher pressure (P1) is described by a straight line with a negative y-intercept. We tested whether extrapolation of such a line also predicts safe decompression to altitude. We substituted tissue nitrogen pressure (P1N2) calculated for a compartment with a 360-min half-time for P1 values; this allows data from hypobaric exposures to be plotted on a P2 vs. P1N2 graph, even if the subject breathes oxygen before ascent. In literature sources, we found 40 reports of human exposures in hypobaric chambers that fell in the region of a P2 vs. P1N2 plot where the extrapolation from hyperbaric data predicted that the decompression should be free of DCS. Of 4,576 exposures, 785 persons suffered decompression sickness (17%), indicating that extrapolation of the diver line to altitude is not valid. Over the pressure range spanned by human hypobaric exposures and hyperbaric air exposures, the best separation between no DCS and DCS on a P2 vs. P1N2 plot seems to be a curve which approximates a straight line in the hyperbaric region but bends toward the origin in the hypobaric region.

Shoran Photogrammetric Mapping Instructions

DTIC Science & Technology

1950-05-15

Armyoufi 16, t t! .: - ! ý 3ý,by The C raazdfrg Officer lngin~er Reserch aca Develolmnt Laboratories Prsperett by Archer M. WilsonL Photogrinmetrio, Brancoh...using agency. The Corps of EnizI.neers is rasponstbie for the final adjustment and analysis of completed control networks resulting from Shoran...path is greatest near the ground., but the path approaches a straight line at higher altitudles where atmosaleric pressure and moisture content become

Detection of soybean in soy-based meat substitutes.

PubMed

Abd Allah, M A; Foda, Y H; el-Dashlouty, S; el-Sanafiry, N Y; Abu Salem, F M

1986-01-01

The statistical analysis of the available data indicated that the straight line equations of protein, fat, fibre, calcium, methionine, and lysine could successively be used for forecasting the added soy percent in a given recipe. On the other hand, the areas of the identified bands in the electropherograms of the investigated samples were considered a reasonable tool for the quantitative determination of whole soybean in soy-based meat substitutes.

Characterization of fine motor development: dynamic analysis of children's drawing movements.

PubMed

Lin, Qiushi; Luo, Jianfei; Wu, Zhongcheng; Shen, Fei; Sun, Zengwu

2015-04-01

In this study, we investigated children's fine motor development by analyzing drawing trajectories, kinematics and kinetics. Straight lines drawing task and circles drawing task were performed by using a force sensitive tablet. Forty right-handed and Chinese mother-tongue students aged 6-12, attending classes from grade 1 to 5, were engaged in the experiment. Three spatial parameters, namely cumulative trace length, vector length of straight line and vertical diameter of circle were determined. Drawing duration, mean drawing velocity, and number of peaks in stroke velocity profile (NPV) were derived as kinematic parameters. Besides mean normal force, two kinetic indices were proposed: normalized force angle regulation (NFR) and variation of fine motor control (VFC) for circles drawing task. The maturation and automation of fine motor ability were reflected by increased drawing velocity, reduced drawing duration, NPV and NFR, with decreased VFC in circles drawing task. Grade and task main effects as well as significant correlations between age and parameters suggest that factors such as schooling, age and task should be considered in the assessment of fine motor skills. Compared with kinematic parameters, findings of NFR and VFC revealed that kinetics is another important perspective in the analysis of fine motor movement. Copyright © 2014 Elsevier B.V. All rights reserved.

Excitation condition analysis of guided wave on PFA tubes for ultrasonic flow meter.

PubMed

Li, Xuan; Xiao, Xufeng; Cao, Li

2016-12-01

Impurity accumulation, which decreases the accuracy of flow measurement, is a critical problem when applying Z-shaped or U-shaped ultrasonic flow meters on straight PFA tubes. It can be expected that the guided wave can be used to implement flow measurement on straight PFA tubes. In this paper, the propagation of guided wave is explained by finite element simulations for the flow meter design. Conditions of guided wave generation, including the excitation frequency and the wedge structure, are studied in the simulations. The wedge is designed as a cone which is friendly to be manufactured and installed. The cone angle, the piezoelectric wafer's resonant frequency and the vibration directions are studied in the simulations. The simulations shows that the propagation of guided wave in thin PFA tubes is influenced by the piezoelectric wafers' resonant frequency and the vibration direction when the mode is on the 'water line'. Based on the results of the simulations, an experiment is conducted to verify the principles of excitation conditions, which performs flow measurement on a straight PFA tube well. Copyright © 2016 Elsevier B.V. All rights reserved.

STUDIES ON THE FORMATION AND IONIZATION OF THE COMPOUNDS OF CASEIN WITH ALKALI

PubMed Central

Greenberg, David M.; Schmidt, Carl L. A.

1924-01-01

1. The results of conductivity experiments with alkali caseinate solutions are given and a graphical method of extrapolation, which gives a straight line, is described. The results of the conductivity experiments are shown to be in accord with the results of the previous transference experiments. 2. The change of conductivity of the alkali caseinate solutions with temperature is shown to follow a straight line relationship. 3. The high value of the mobility which was obtained for the casein ion and the high temperature gradient are discussed in relation to McBain's theory of colloidal electrolytes. PMID:19872136

Modeling and experimental characterization of electromigration in interconnect trees

NASA Astrophysics Data System (ADS)

Thompson, C. V.; Hau-Riege, S. P.; Andleigh, V. K.

1999-11-01

Most modeling and experimental characterization of interconnect reliability is focussed on simple straight lines terminating at pads or vias. However, laid-out integrated circuits often have interconnects with junctions and wide-to-narrow transitions. In carrying out circuit-level reliability assessments it is important to be able to assess the reliability of these more complex shapes, generally referred to as `trees.' An interconnect tree consists of continuously connected high-conductivity metal within one layer of metallization. Trees terminate at diffusion barriers at vias and contacts, and, in the general case, can have more than one terminating branch when they include junctions. We have extended the understanding of `immortality' demonstrated and analyzed for straight stud-to-stud lines, to trees of arbitrary complexity. This leads to a hierarchical approach for identifying immortal trees for specific circuit layouts and models for operation. To complete a circuit-level-reliability analysis, it is also necessary to estimate the lifetimes of the mortal trees. We have developed simulation tools that allow modeling of stress evolution and failure in arbitrarily complex trees. We are testing our models and simulations through comparisons with experiments on simple trees, such as lines broken into two segments with different currents in each segment. Models, simulations and early experimental results on the reliability of interconnect trees are shown to be consistent.

27 CFR 9.185 - Texoma.

Code of Federal Regulations, 2010 CFR

2010-04-01

...; and (2) Texarkana, Tex.; Ark.; Okla.; La., 1953, revised 1972. (c) Boundary. The Texoma viticultural... the Red River eastward along the Texas-Oklahoma State line, passes onto the Texarkana map, and... Texarkana map crosses the county line; then (4) Continues southwest in a straight line for approximately 13...

27 CFR 9.185 - Texoma.

Code of Federal Regulations, 2012 CFR

2012-04-01

...; and (2) Texarkana, Tex.; Ark.; Okla.; La., 1953, revised 1972. (c) Boundary. The Texoma viticultural... the Red River eastward along the Texas-Oklahoma State line, passes onto the Texarkana map, and... Texarkana map crosses the county line; then (4) Continues southwest in a straight line for approximately 13...

27 CFR 9.185 - Texoma.

Code of Federal Regulations, 2013 CFR

2013-04-01

...; and (2) Texarkana, Tex.; Ark.; Okla.; La., 1953, revised 1972. (c) Boundary. The Texoma viticultural... the Red River eastward along the Texas-Oklahoma State line, passes onto the Texarkana map, and... Texarkana map crosses the county line; then (4) Continues southwest in a straight line for approximately 13...

27 CFR 9.185 - Texoma.

Code of Federal Regulations, 2011 CFR

2011-04-01

...; and (2) Texarkana, Tex.; Ark.; Okla.; La., 1953, revised 1972. (c) Boundary. The Texoma viticultural... the Red River eastward along the Texas-Oklahoma State line, passes onto the Texarkana map, and... Texarkana map crosses the county line; then (4) Continues southwest in a straight line for approximately 13...

27 CFR 9.185 - Texoma.

Code of Federal Regulations, 2014 CFR

2014-04-01

...; and (2) Texarkana, Tex.; Ark.; Okla.; La., 1953, revised 1972. (c) Boundary. The Texoma viticultural... the Red River eastward along the Texas-Oklahoma State line, passes onto the Texarkana map, and... Texarkana map crosses the county line; then (4) Continues southwest in a straight line for approximately 13...

27 CFR 9.169 - Red Hills Lake County.

Code of Federal Regulations, 2014 CFR

2014-04-01

...-foot contour line with the section 17 east boundary line, and continue for about 0.45 miles along the...-foot elevation line (Kelseyville Quadrangle); then (18) Proceed about 1.35 miles straight easterly to... 4, T12N, R7W, proceed approximately 0.1 miles due south along the common section line to its...

The long-solved problem of the best-fit straight line: Application to isotopic mixing lines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wehr, Richard; Saleska, Scott R.

It has been almost 50 years since York published an exact and general solution for the best-fit straight line to independent points with normally distributed errors in both x and y. York's solution is highly cited in the geophysical literature but almost unknown outside of it, so that there has been no ebb in the tide of books and papers wrestling with the problem. Much of the post-1969 literature on straight-line fitting has sown confusion not merely by its content but by its very existence. The optimal least-squares fit is already known; the problem is already solved. Here we introducemore » the non-specialist reader to York's solution and demonstrate its application in the interesting case of the isotopic mixing line, an analytical tool widely used to determine the isotopic signature of trace gas sources for the study of biogeochemical cycles. The most commonly known linear regression methods – ordinary least-squares regression (OLS), geometric mean regression (GMR), and orthogonal distance regression (ODR) – have each been recommended as the best method for fitting isotopic mixing lines. In fact, OLS, GMR, and ODR are all special cases of York's solution that are valid only under particular measurement conditions, and those conditions do not hold in general for isotopic mixing lines. Here, using Monte Carlo simulations, we quantify the biases in OLS, GMR, and ODR under various conditions and show that York's general – and convenient – solution is always the least biased.« less

The long-solved problem of the best-fit straight line: Application to isotopic mixing lines

DOE PAGES

Wehr, Richard; Saleska, Scott R.

2017-01-03

It has been almost 50 years since York published an exact and general solution for the best-fit straight line to independent points with normally distributed errors in both x and y. York's solution is highly cited in the geophysical literature but almost unknown outside of it, so that there has been no ebb in the tide of books and papers wrestling with the problem. Much of the post-1969 literature on straight-line fitting has sown confusion not merely by its content but by its very existence. The optimal least-squares fit is already known; the problem is already solved. Here we introducemore » the non-specialist reader to York's solution and demonstrate its application in the interesting case of the isotopic mixing line, an analytical tool widely used to determine the isotopic signature of trace gas sources for the study of biogeochemical cycles. The most commonly known linear regression methods – ordinary least-squares regression (OLS), geometric mean regression (GMR), and orthogonal distance regression (ODR) – have each been recommended as the best method for fitting isotopic mixing lines. In fact, OLS, GMR, and ODR are all special cases of York's solution that are valid only under particular measurement conditions, and those conditions do not hold in general for isotopic mixing lines. Here, using Monte Carlo simulations, we quantify the biases in OLS, GMR, and ODR under various conditions and show that York's general – and convenient – solution is always the least biased.« less

46 CFR Appendix A to Part 45 - Load Line Certificate Form

Code of Federal Regulations, 2011 CFR

2011-10-01

... registry Type of Ship: TYPE “A” TYPE “B” TYPE “B” with increased freeboard freeboard from deck line Midsummer MS Summer S Intermediate I Winter W load line above S Upper edge of line through center of diamond... salt water of the St. Lawrence River west of a straight line from Cap de Rosiers to West Point...

System for line drawings interpretation

NASA Astrophysics Data System (ADS)

Boatto, L.; Consorti, Vincenzo; Del Buono, Monica; Eramo, Vincenzo; Esposito, Alessandra; Melcarne, F.; Meucci, Mario; Mosciatti, M.; Tucci, M.; Morelli, Arturo

1992-08-01

This paper describes an automatic system that extracts information from line drawings, in order to feed CAD or GIS systems. The line drawings that we analyze contain interconnected thin lines, dashed lines, text, and symbols. Characters and symbols may overlap with lines. Our approach is based on the properties of the run representation of a binary image that allow giving the image a graph structure. Using this graph structure, several algorithms have been designed to identify, directly in the raster image, straight segments, dashed lines, text, symbols, hatching lines, etc. Straight segments and dashed lines are converted into vectors, with high accuracy and good noise immunity. Characters and symbols are recognized by means of a recognizer, specifically developed for this application, designed to be insensitive to rotation and scaling. Subsequent processing steps include an `intelligent'' search through the graph in order to detect closed polygons, dashed lines, text strings, and other higher-level logical entities, followed by the identification of relationships (adjacency, inclusion, etc.) between them. Relationships are further translated into a formal description of the drawing. The output of the system can be used as input to a Geographic Information System package. The system is currently used by the Italian Land Register Authority to process cadastral maps.

The Dung Beetle Dance: An Orientation Behaviour?

PubMed Central

Baird, Emily; Byrne, Marcus J.; Smolka, Jochen; Warrant, Eric J.; Dacke, Marie

2012-01-01

An interesting feature of dung beetle behaviour is that once they have formed a piece of dung into a ball, they roll it along a straight path away from the dung pile. This straight-line orientation ensures that the beetles depart along the most direct route, guaranteeing that they will not return to the intense competition (from other beetles) that occurs near the dung pile. Before rolling a new ball away from the dung pile, dung beetles perform a characteristic “dance,” in which they climb on top of the ball and rotate about their vertical axis. This dance behaviour can also be observed during the beetles' straight-line departure from the dung pile. The aim of the present study is to investigate the purpose of the dung beetle dance. To do this, we explored the circumstances that elicit dance behaviour in the diurnal ball-rolling dung beetle, Scarabaeus (Kheper) nigroaeneus. Our results reveal that dances are elicited when the beetles lose control of their ball or lose contact with it altogether. We also find that dances can be elicited by both active and passive deviations of course and by changes in visual cues alone. In light of these results, we hypothesise that the dung beetle dance is a visually mediated mechanism that facilitates straight-line orientation in ball-rolling dung beetles by allowing them to 1) establish a roll bearing and 2) return to this chosen bearing after experiencing a disturbance to the roll path. PMID:22279572

Oculogravic illusion in response to straight-ahead acceleration of a CF-104 aircraft

NASA Technical Reports Server (NTRS)

Graybiel, A.; Jennings, G. L.; Johnson, W. H.; Money, K. E.; Malcolm, R. E.

1979-01-01

Experimental subjects wore goggles that restricted monocular vision to a luminous line fixed relative to the head, and they were exposed on one occasion to a straight-ahead acceleration of an aircraft and on another occasion to a tilting chair. The magnitude of change of direction of the resultant acceleration was the same on both occasions, but the perceived movement of the luminous line from the two stimuli was very different. In response to the aircraft stimulus, the oculogravic illusion was experienced and the luminous line was perceived as tilting relative to the subject, in response to the tilting chair stimulus, the line was perceived as remaining fixed relative to the subject. It was concluded that the oculogravic illusion, as experienced in the aircraft (and previously in centrifuges), is a true illusion and not merely a fact of physics.

Spring Regimes

DTIC Science & Technology

2003-04-15

of Albuquerque, New Mexico. . Since the system has “bottomed out” one could project a straight line northeastward (with little eastward movement of...in determining if forecast model guidance is “on track.” 14. 14. Subject Terms: CLOUDS, COMMA CLOUD, DRY LINE , GULF STRATUS, HEIGHT FALL CENTERS...4-40 Warm Fronts, Squall Lines and Mesocyclones

27 CFR 9.169 - Red Hills Lake County.

Code of Federal Regulations, 2012 CFR

2012-04-01

...-foot contour line with the section 17 east boundary line, and continue for about 0.45 miles along the... continue straight north 0.25 miles on Wilkinson Road to its intersection with the 1,600-foot elevation line...-foot elevation line, section 19, T13N, R8W (Kelseyville Quadrangle); then (20) Proceed about 3.0 miles...

27 CFR 9.169 - Red Hills Lake County.

Code of Federal Regulations, 2013 CFR

2013-04-01

...-foot contour line with the section 17 east boundary line, and continue for about 0.45 miles along the... continue straight north 0.25 miles on Wilkinson Road to its intersection with the 1,600-foot elevation line...-foot elevation line, section 19, T13N, R8W (Kelseyville Quadrangle); then (20) Proceed about 3.0 miles...

27 CFR 9.131 - Mt. Harlan.

Code of Federal Regulations, 2010 CFR

2010-04-01

... beginning is the unnamed 3,063′ peak on the county line between San Benito and Monterey Counties in Township... Sections 32, 29, and 30 all in Township 14 S., Range 5 E., to the point at which the county line intersects the line between Sections 30 and 19 of said Township and Range. (3) Thence proceed in a straight line...

27 CFR 9.131 - Mt. Harlan.

Code of Federal Regulations, 2011 CFR

2011-04-01

... beginning is the unnamed 3,063′ peak on the county line between San Benito and Monterey Counties in Township... Sections 32, 29, and 30 all in Township 14 S., Range 5 E., to the point at which the county line intersects the line between Sections 30 and 19 of said Township and Range. (3) Thence proceed in a straight line...

Fingering instability of Bingham fluids

NASA Astrophysics Data System (ADS)

Ghadge, Shilpa; Myers, Tim

2005-11-01

Contact line instabilities have been extensively studied and many useful results obtained for industrial applications. Our research in this area is to explore these instabilities for non-Newtonian fluids which has wide scope in geological, biological as well as industrial areas. In this talk, we will present an analysis of fingering instability near a contact line of the thin sheet of fluid flowing down on a moderately inclined plane. This instability has been well studied for Newtonian fluids. We explore the effect of a yield strength of the fluid on this instability. We have conveniently assumed the presence of the precussor film of small thickness ahead of the fluid film to avoid some mathematical singularities. Using a lubrication-type approximation, we perform a linear stability analysis of a straight contact line. We will show comparison with some experimental results using suspensions of kaolin in silicone oil as a yield strength fluid.

Change Detection of High-Resolution Remote Sensing Images Based on Adaptive Fusion of Multiple Features

NASA Astrophysics Data System (ADS)

Wang, G. H.; Wang, H. B.; Fan, W. F.; Liu, Y.; Chen, C.

2018-04-01

In view of the traditional change detection algorithm mainly depends on the spectral information image spot, failed to effectively mining and fusion of multi-image feature detection advantage, the article borrows the ideas of object oriented analysis proposed a multi feature fusion of remote sensing image change detection algorithm. First by the multi-scale segmentation of image objects based; then calculate the various objects of color histogram and linear gradient histogram; utilizes the color distance and edge line feature distance between EMD statistical operator in different periods of the object, using the adaptive weighted method, the color feature distance and edge in a straight line distance of combination is constructed object heterogeneity. Finally, the curvature histogram analysis image spot change detection results. The experimental results show that the method can fully fuse the color and edge line features, thus improving the accuracy of the change detection.

Raft cultivation area extraction from high resolution remote sensing imagery by fusing multi-scale region-line primitive association features

NASA Astrophysics Data System (ADS)

Wang, Min; Cui, Qi; Wang, Jie; Ming, Dongping; Lv, Guonian

2017-01-01

In this paper, we first propose several novel concepts for object-based image analysis, which include line-based shape regularity, line density, and scale-based best feature value (SBV), based on the region-line primitive association framework (RLPAF). We then propose a raft cultivation area (RCA) extraction method for high spatial resolution (HSR) remote sensing imagery based on multi-scale feature fusion and spatial rule induction. The proposed method includes the following steps: (1) Multi-scale region primitives (segments) are obtained by image segmentation method HBC-SEG, and line primitives (straight lines) are obtained by phase-based line detection method. (2) Association relationships between regions and lines are built based on RLPAF, and then multi-scale RLPAF features are extracted and SBVs are selected. (3) Several spatial rules are designed to extract RCAs within sea waters after land and water separation. Experiments show that the proposed method can successfully extract different-shaped RCAs from HR images with good performance.

Drug advertising and prescribing

PubMed Central

Dajda, Richard

1978-01-01

A study of the amount of drug advertisements received by general practitioners and the amount of the drugs practitioners prescribed showed a strong correlation of 0·80. Analysis suggests that a straight line graphic relationship provides the best fit for the results obtained. Further analysis of the quantity of advertising in relation to the amount of prescribing revealed two groups of drugs: those which were relatively more and those which were relatively less often advertised in proportion to the number of prescriptions issued for them. ImagesFigure 1.Figure 2. PMID:739456

Trajectory planning and control of a 6 DOF manipulator with Stewart platform-based mechanism

NASA Technical Reports Server (NTRS)

Nguyen, Charles C.; Antrazi, Sami

1990-01-01

The trajectory planning and control was studied of a robot manipulator that has 6 degrees of freedom and was designed based on the mechanism of the Stewart Platform. First the main components of the manipulator is described along with its operation. The solutions are briefly prescribed for the forward and inverse kinematics of the manipulator. After that, two trajectory planning schemes are developed using the manipulator inverse kinematics to track straight lines and circular paths. Finally experiments conducted to study the performance of the developed planning schemes in tracking a straight line and a circle are presented and discussed.

Normal probability plots with confidence.

PubMed

Chantarangsi, Wanpen; Liu, Wei; Bretz, Frank; Kiatsupaibul, Seksan; Hayter, Anthony J; Wan, Fang

2015-01-01

Normal probability plots are widely used as a statistical tool for assessing whether an observed simple random sample is drawn from a normally distributed population. The users, however, have to judge subjectively, if no objective rule is provided, whether the plotted points fall close to a straight line. In this paper, we focus on how a normal probability plot can be augmented by intervals for all the points so that, if the population distribution is normal, then all the points should fall into the corresponding intervals simultaneously with probability 1-α. These simultaneous 1-α probability intervals provide therefore an objective mean to judge whether the plotted points fall close to the straight line: the plotted points fall close to the straight line if and only if all the points fall into the corresponding intervals. The powers of several normal probability plot based (graphical) tests and the most popular nongraphical Anderson-Darling and Shapiro-Wilk tests are compared by simulation. Based on this comparison, recommendations are given in Section 3 on which graphical tests should be used in what circumstances. An example is provided to illustrate the methods. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Adaptive Control of Small Outboard-Powered Boats for Survey Applications

NASA Technical Reports Server (NTRS)

VanZwieten, T.S.; VanZwieten, J.H.; Fisher, A.D.

2009-01-01

Four autopilot controllers have been developed in this work that can both hold a desired heading and follow a straight line. These PID, adaptive PID, neuro-adaptive, and adaptive augmenting control algorithms have all been implemented into a numerical simulation of a 33-foot center console vessel with wind, waves, and current disturbances acting in the perpendicular (across-track) direction of the boat s desired trajectory. Each controller is tested for its ability to follow a desired heading in the presence of these disturbances and then to follow a straight line at two different throttle settings for the same disturbances. These controllers were tuned for an input thrust of 2000 N and all four controllers showed good performance with none of the controllers significantly outperforming the others when holding a constant heading and following a straight line at this engine thrust. Each controller was then tested for a reduced engine thrust of 1200 N per engine where each of the three adaptive controllers reduced heading error and across-track error by approximately 50% after a 300 second tuning period when compared to the fixed gain PID, showing that significant robustness to changes in throttle setting was gained by using an adaptive algorithm.

Comparison of perceived and modelled geographical access to accident and emergency departments: a cross-sectional analysis from the Caerphilly Health and Social Needs Study.

PubMed

Fone, David L; Christie, Stephen; Lester, Nathan

2006-04-13

Assessment of the spatial accessibility of hospital accident and emergency departments as perceived by local residents has not previously been investigated. Perceived accessibility may affect where, when, and whether potential patients attend for treatment. Using data on 11,853 respondents to a population survey in Caerphilly county borough, Wales, UK, we present an analysis comparing the accessibility of accident and emergency departments as reported by local residents and drive-time to the nearest accident and emergency department modelled using a geographical information system (GIS). Median drive-times were significantly shorter in the lowest perceived access category and longer in the best perceived access category (p < 0.001). The perceived access and GIS modelled drive-time variables were positively correlated (Spearman's rank correlation coefficient, r = 0.38, p < 0.01). The strongest correlation was found for respondents living in areas in which nearly all households had a car or van (r = 0.47, p < 0.01). Correlations were stronger among respondents reporting good access to public transport and among those reporting a recent accident and emergency attendance for injury treatment compared to other respondents. Correlation coefficients did not vary substantially by levels of household income. Drive-time, road distance and straight-line distance were highly inter-correlated and substituting road distance or straight-line distance as the GIS modelled spatial accessibility measure only marginally decreased the magnitude of the correlations between perceived and GIS modelled access. This study provides evidence that the accessibility of hospital-based health care services as perceived by local residents is related to measures of spatial accessibility modelled using GIS. For studies that aim to model geographical separation in a way that correlates well with the perception of local residents, there may be minimal advantage in using sophisticated measures. Straight-line distance, which can be calculated without GIS, may be as good as GIS-modelled drive-time or distance for this purpose. These findings will be of importance to health policy makers and local planners who seek to obtain local information on access to services through focussed assessments of residents' concerns over accessibility and GIS modelling.

Lungeing on hard and soft surfaces: Movement symmetry of trotting horses considered sound by their owners.

PubMed

Pfau, T; Jennings, C; Mitchell, H; Olsen, E; Walker, A; Egenvall, A; Tröster, S; Weller, R; Rhodin, M

2016-01-01

Lungeing is often part of the clinical lameness examination. The difference in movement symmetry, which is a commonly employed lameness measure, has not been quantified between surfaces. To compare head and pelvic movement symmetry between surfaces and reins during lungeing. Quantitative gait analysis in 23 horses considered sound by their owners. Twenty-three horses were assessed in-hand and on the lunge on both reins on hard and soft surfaces with inertial sensors. Seven movement symmetry parameters were quantified and used to establish 2 groups, namely symmetrical (n = 9) and forelimb-lame horses (n = 14), based on values from straight-line assessment. Movement symmetry values for left rein measurements were side corrected to allow comparison of the amount of movement symmetry between reins. A mixed model (P<0.05) was used to study effects on movement symmetry of surface (hard/soft) and rein (inside/outside with respect to movement symmetry on the straight). In forelimb-lame horses, surface and rein were identified as significantly affecting all head movement symmetry measures (rein, all P<0.0001; surface, all P<0.042). In the symmetrical group, no significant influence of surface or rein was identified for head movement symmetry (rein, all P>0.245; surface, all P>0.073). No significant influence of surface or rein was identified for any of the pelvic movement symmetry measures in either group. While more symmetrical horses showed a consistent amount of movement symmetry across surfaces/reins, horses objectively quantified as lame on the straight showed decreased movement symmetry during lungeing, in particular with the lame limb on the inside of a hard circle. The variation within group questions straight-line movement symmetry as a sole measure of lameness without quantification of movement symmetry on the lunge, ideally on hard and soft surfaces to evaluate differences between reins and surfaces. In future, thresholds for lungeing need to be determined using simultaneous visual and objective assessment. © 2014 EVJ Ltd.

27 CFR 9.204 - Tracy Hills.

Code of Federal Regulations, 2010 CFR

2010-04-01

... and Lammers Ferry Road, along the western boundary line of section 6, T3S/R5E. From the beginning... Western Pacific Railway line along the southern boundary line of section 6, T3S/R5E (Tracy map); then (2) Proceed 5.6 miles straight east along the Western Pacific Railway line and then along Linne Road to the...

27 CFR 9.215 - Lake Chelan.

Code of Federal Regulations, 2014 CFR

2014-04-01

... section 10 for 0.3 mile to its intersection with the 2,520-foot contour line and a 90-degree turn in the... boundary line 0.3 mile to its intersection with the 2,600-foot contour line and a 90-degree turn in the WNF... Landing. From the beginning point, proceed straight east 1.6 miles along the northern boundary line of...

27 CFR 9.230 - Ballard Canyon.

Code of Federal Regulations, 2014 CFR

2014-04-01

... straight line approximately 1.25 miles, crossing onto the Zaca Creek map, to the marked “Ball” 801-foot....45 miles, crossing onto the Solvang map, to a marked, unnamed 775-foot peak, T6N/R31W; then (6... the 400-foot contour line approximately 1.5 miles, to the contour line's first intersection with...

Line intersect sampling: Ell-shaped transects and multiple intersections

Treesearch

Timothy G. Gregoire; Harry T. Valentine

2003-01-01

The probability of selecting a population element under line intersect sampling depends on the width of the particle in the direction perpendicular to the transect, as is well known. The consequence of this when using ell-shaped transects rather than straight-line transects are explicated, and modifications that preserve design-unbiasedness of Kaiser's (1983)...

Responsiveness of Nigerian Students to Pictorial Depth Cues.

ERIC Educational Resources Information Center

Evans, G. S.; Seddon, G. M.

1978-01-01

Three groups of Nigerian high school and college students were tested for response to four pictorial depth cues. Students had more difficulty with cues concerning the relative size of objects and the foreshortening of straight lines than with cues involving overlap of lines and distortion of the angles between lines. (Author/JEG)

27 CFR 9.45 - Suisun Valley.

Code of Federal Regulations, 2011 CFR

2011-04-01

... township line “T5N/T4N”; (2) Thence in a straight line in a northeast direction to Bench Mark (BM) 19... just south of Section 34, Township 6 North, Range 2 West; (5) Thence due west along the Napa/Solano...

27 CFR 9.45 - Suisun Valley.

Code of Federal Regulations, 2010 CFR

2010-04-01

... township line “T5N/T4N”; (2) Thence in a straight line in a northeast direction to Bench Mark (BM) 19... just south of Section 34, Township 6 North, Range 2 West; (5) Thence due west along the Napa/Solano...

Rapidity evolution of Wilson lines at the next-to-leading order

DOE Office of Scientific and Technical Information (OSTI.GOV)

Balitsky, Ian; Chirilli, Giovanni

2013-12-01

At high energies particles move very fast so the proper degrees of freedom for the fast gluons moving along the straight lines are Wilson-line operators - infinite gauge factors ordered along the line. In the framework of operator expansion in Wilson lines the energy dependence of the amplitudes is determined by the rapidity evolution of Wilson lines. We present the next-to-leading order hierarchy of the evolution equations for Wilson-line operators.

Kinematics of center of mass and center of pressure predict friction requirement at shoe-floor interface during walking.

PubMed

Yamaguchi, Takeshi; Yano, Masaru; Onodera, Hiroshi; Hokkirigawa, Kazuo

2013-06-01

We aimed to determine whether inclination angles of the line connecting the whole body center of mass (COM) to the center of pressure (COP) (COM-COP angle) help predict the required coefficient of friction (RCOF) in young adult males during the weight acceptance and push-off phases in transient movements such as turning, gait termination and initiation, and steady-state movements such as straight walking. Seventeen healthy young adult males were asked to (1) walk in a straight line, (2) turn 60° with either foot (step and spin turns), and (3) initiate and terminate walking on a dry level floor. Peak absolute values of the ratio between resultant horizontal and vertical ground reaction forces during the weight acceptance and push-off phases (RCOFh and RCOFt, respectively) were calculated. COM-COP angles θh and θt at the instant of RCOFh and RCOFt, respectively, were also calculated. Bivariate regression analysis demonstrated that the |θh| and |θt| tangents were significant predictors of RCOFh (R = 0.878; R(2) = 0.770; p<0.001) and RCOFt (R = 0.918; R(2) = 0.843; p<0.001), respectively. The results suggest that COM and COP kinematics (i.e., the COM-COP angle) serve as a predictor of friction requirement during the weight acceptance and push-off phases in steady-state movements such as straight walking and transient movements such as turning as well as gait termination and initiation. Copyright © 2012 Elsevier B.V. All rights reserved.

A change in paradigm: lowering blood pressure in everyone over a certain age.

PubMed

Law, Malcolm

2012-06-01

Dividing people into 'hypertensives' and 'normotensives' is commonplace but problematic. The relationship between blood pressure and cardiovascular disease is continuous. The Prospective Studies Collaboration analysis shows a continuous straight line dose-response relationship across the entire population down to blood pressure levels of 115 mmHg systolic and 75 mmHg diastolic, the confidence limits on the individual data points being sufficiently narrow to exclude even a minor deviation from a linear relationship. Meta-analysis of randomized controlled trials shows that blood pressure-lowering drugs produce similar proportional reductions in risk of coronary heart disease (CHD) and stroke irrespective of pre-treatment blood pressure, down to levels of 110 mmHg systolic and 70 mmHg diastolic. There are also now sufficient trial data to show a statistically significant risk reduction in 'normotensive' people without known vascular disease on entry. The straight line (log-linear) relationship means that the benefit derived from lowering blood pressure is proportional to existing risk, so the decision on whom to treat with blood pressure-lowering drugs should depend on a person's overall absolute risk irrespective of blood pressure. In primary prevention, basing treatment on age alone rather than overall absolute risk entails little loss of efficacy and may be preferred on the basis of simplicity and avoidance of anxiety in telling people they are at elevated risk.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shi, E. L.; Hammett, G. W.; Stoltzfus-Dueck, T.

Here, five-dimensional gyrokinetic continuum simulations of electrostatic plasma turbulence in a straight, open-field-line geometry have been performed using a full- discontinuous-Galerkin approach implemented in the Gkeyll code. While various simplifications have been used for now, such as long-wavelength approximations in the gyrokinetic Poisson equation and the Hamiltonian, these simulations include the basic elements of a fusion-device scrape-off layer: localised sources to model plasma outflow from the core, cross-field turbulent transport, parallel flow along magnetic field lines, and parallel losses at the limiter or divertor with sheath-model boundary conditions. The set of sheath-model boundary conditions used in the model allows currentsmore » to flow through the walls. In addition to details of the numerical approach, results from numerical simulations of turbulence in the Large Plasma Device, a linear device featuring straight magnetic field lines, are presented.« less

Human pair walking behavior: evaluation of cooperation strategies

NASA Astrophysics Data System (ADS)

Dobramysl, Ulrich; Bodova, Katarina; Kollar, Richard; Erban, Radek

2015-03-01

Human walkers are notoriously poor at keeping a direction without external cues: Experimental work by Souman et al. with blindfolded subjects told to walk in a straight line revealed intriguing circular and spiraling trajectories, which can be approximated by a stochastic process. In this work, motivated by pair walking experiments by Miglierini et al., we introduce an analysis of various strategies employed by a pair of blindfolded walkers, who are communicating via auditory cues, to maximize their efficiency at walking straight. To this end, we characterize pairs of strategies such as free walking, side-by-side walking and unconditional following from data generated by robot pair walking experiments (using computer vision techniques) and numerical simulations. We extract the mean exit distances of walker pairs from a corridor with finite width to construct phase portraits of the walking performance. We find intriguing cooperative effects leading to non-trivial enhancements of the efficiency at walking straight. The research leading to these results has received funding from the European Research Council under the European Community's Seventh Framework Programme (FP7/2007-2013) / ERC Grant Agreement No. 239870; and from the Royal Society through a Research Grant.

A1C Test and Diabetes

MedlinePlus

... per day (fasting or pre-breakfast, pre-lunch, pre-dinner, and bedtime). The straight black line shows an A1C measurement of 7.0 percent. The blue line shows an example of how blood glucose test results might look from self-monitoring four times ...

An unexplained three-dimensional percept emerging from a bundle of lines.

PubMed

Altschuler, Eric L; Huang, Abigail E; Kim, Hee J; Battaglini, Luca; Roncato, Sergio

2017-10-01

Perceptual grouping has been extensively studied, but some areas are still unexplored-in particular, the figural organizations that emerge when bundles of intersecting lines are drawn. Here, we will describe some figural organizations that emerge after the superimposition of bundles of lines forming the profile of regular triangular waves. By manipulating the lines' jaggedness and junction geometry (regular or irregular X junction) we could generate the following organizations: (a) a grid, or a figural configuration in which both the lines and closed contours are perceived, (b) a figure-ground organization composed of figures separated by portions of the background, and (c) a corrugated surface appearing as a multifaceted polyhedral shell crossed by ridges and valleys. An experiment was conducted with the aim at testing the role of the good-continuation and closure Gestalt factors. Good continuation prevails when the lines are straight or close to straightness, but its role is questionable in the appearance of a corrugated surface. This perceptual organization occurs despite the violation of the good-continuation rule and consists of a structure of such complexity so as to challenge algorithms of computer vision and stimulate a deeper understanding of the perceptual interpretation of groups of lines.

DIAC object recognition system

NASA Astrophysics Data System (ADS)

Buurman, Johannes

1992-03-01

This paper describes the object recognition system used in an intelligent robot cell. It is used to recognize and estimate pose and orientation of parts as they enter the cell. The parts are mostly metal and consist of polyhedral and cylindrical shapes. The system uses feature-based stereo vision to acquire a wireframe of the observed part. Features are defined as straight lines and ellipses, which lead to a wireframe of straight lines and circular arcs (the latter using a new algorithm). This wireframe is compared to a number of wire frame models obtained from the CAD database. Experimental results show that image processing hardware and parallelization may add considerably to the speed of the system.

Rater agreement of visual lameness assessment in horses during lungeing.

PubMed

Hammarberg, M; Egenvall, A; Pfau, T; Rhodin, M

2016-01-01

Lungeing is an important part of lameness examinations as the circular path may accentuate low-grade lameness. Movement asymmetries related to the circular path, to compensatory movements and to pain make the lameness evaluation complex. Scientific studies have shown high inter-rater variation when assessing lameness during straight line movement. The aim was to estimate inter- and intra-rater agreement of equine veterinarians evaluating lameness from videos of sound and lame horses during lungeing and to investigate the influence of veterinarians' experience and the objective degree of movement asymmetry on rater agreement. Cross-sectional observational study. Video recordings and quantitative gait analysis with inertial sensors were performed in 23 riding horses of various breeds. The horses were examined at trot on a straight line and during lungeing on soft or hard surfaces in both directions. One video sequence was recorded per condition and the horses were classified as forelimb lame, hindlimb lame or sound from objective straight line symmetry measurements. Equine veterinarians (n = 86), including 43 with >5 years of orthopaedic experience, participated in a web-based survey and were asked to identify the lamest limb on 60 videos, including 10 repeats. The agreements between (inter-rater) and within (intra-rater) veterinarians were analysed with κ statistics (Fleiss, Cohen). Inter-rater agreement κ was 0.31 (0.38/0.25 for experienced/less experienced) and higher for forelimb (0.33) than for hindlimb lameness (0.11) or soundness (0.08) evaluation. Median intra-rater agreement κ was 0.57. Inter-rater agreement was poor for less experienced raters, and for all raters when evaluating hindlimb lameness. Since identification of the lame limb/limbs is a prerequisite for successful diagnosis, treatment and recovery, the high inter-rater variation when evaluating lameness on the lunge is likely to influence the accuracy and repeatability of lameness examinations and, indirectly, the efficacy of treatment. © 2015 The Authors. Equine Veterinary Journal published by John Wiley & Sons Ltd on behalf of EVJ Ltd.

Rater agreement of visual lameness assessment in horses during lungeing

PubMed Central

Hammarberg, M.; Egenvall, A.; Pfau, T.

2015-01-01

Summary Reasons for performing study Lungeing is an important part of lameness examinations as the circular path may accentuate low‐grade lameness. Movement asymmetries related to the circular path, to compensatory movements and to pain make the lameness evaluation complex. Scientific studies have shown high inter‐rater variation when assessing lameness during straight line movement. Objectives The aim was to estimate inter‐ and intra‐rater agreement of equine veterinarians evaluating lameness from videos of sound and lame horses during lungeing and to investigate the influence of veterinarians’ experience and the objective degree of movement asymmetry on rater agreement. Study design Cross‐sectional observational study. Methods Video recordings and quantitative gait analysis with inertial sensors were performed in 23 riding horses of various breeds. The horses were examined at trot on a straight line and during lungeing on soft or hard surfaces in both directions. One video sequence was recorded per condition and the horses were classified as forelimb lame, hindlimb lame or sound from objective straight line symmetry measurements. Equine veterinarians (n = 86), including 43 with >5 years of orthopaedic experience, participated in a web‐based survey and were asked to identify the lamest limb on 60 videos, including 10 repeats. The agreements between (inter‐rater) and within (intra‐rater) veterinarians were analysed with κ statistics (Fleiss, Cohen). Results Inter‐rater agreement κ was 0.31 (0.38/0.25 for experienced/less experienced) and higher for forelimb (0.33) than for hindlimb lameness (0.11) or soundness (0.08) evaluation. Median intra‐rater agreement κ was 0.57. Conclusions Inter‐rater agreement was poor for less experienced raters, and for all raters when evaluating hindlimb lameness. Since identification of the lame limb/limbs is a prerequisite for successful diagnosis, treatment and recovery, the high inter‐rater variation when evaluating lameness on the lunge is likely to influence the accuracy and repeatability of lameness examinations and, indirectly, the efficacy of treatment. PMID:25399722

33 CFR 80.712 - Morris Island, SC to Hilton Head Island, SC.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Island. (d) A line drawn from the microwave antenna tower on Edisto Beach charted in approximate position..., SC to Hilton Head Island, SC. (a) A line drawn from the easternmost tip of Folley Island to the... Island. (b) A straight line drawn from the seaward tangent of Folly Island through Folly River Daybeacon...

33 CFR 80.712 - Morris Island, SC to Hilton Head Island, SC.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Island. (d) A line drawn from the microwave antenna tower on Edisto Beach charted in approximate position..., SC to Hilton Head Island, SC. (a) A line drawn from the easternmost tip of Folley Island to the... Island. (b) A straight line drawn from the seaward tangent of Folly Island through Folly River Daybeacon...

50 CFR 660.399 - EFH Conservation Areas off the Coast of California.

Code of Federal Regulations, 2010 CFR

2010-10-01

.... The boundary of the Harris Point EFH Conservation Area is defined by the mean high water line and... commercial and recreational take of living marine resources is allowed, exists between the mean high water... Scorpion EFH Conservation Area is defined by the mean high water line and a straight line connecting all of...

50 CFR 660.79 - EFH Conservation Areas off the Coast of California.

Code of Federal Regulations, 2011 CFR

2011-10-01

.... The boundary of the Harris Point EFH Conservation Area is defined by the mean high water line and... commercial and recreational take of living marine resources is allowed, exists between the mean high water... Scorpion EFH Conservation Area is defined by the mean high water line and a straight line connecting all of...

A computer program (MACPUMP) for interactive aquifer-test analysis

USGS Publications Warehouse

Day-Lewis, F. D.; Person, M.A.; Konikow, Leonard F.

1995-01-01

This report introduces MACPUMP (Version 1.0), an aquifer-test-analysis package for use with Macintosh4 computers. The report outlines the input- data format, describes the solutions encoded in the program, explains the menu-items, and offers a tutorial illustrating the use of the program. The package reads list-directed aquifer-test data from a file, plots the data to the screen, generates and plots type curves for several different test conditions, and allows mouse-controlled curve matching. MACPUMP features pull-down menus, a simple text viewer for displaying data-files, and optional on-line help windows. This version includes the analytical solutions for nonleaky and leaky confined aquifers, using both type curves and straight-line methods, and for the analysis of single-well slug tests using type curves. An executable version of the code and sample input data sets are included on an accompanying floppy disk.

27 CFR 9.222 - Naches Heights.

Code of Federal Regulations, 2012 CFR

2012-04-01

... the intersection of the Burlington Northern single-track rail line and the Congdon (Schuler) Canal... a straight line approximately 0.15 mile to the Congdon (Schuler) Canal, which closely parallels the... Congdon (Schuler) Canal, onto the Selah map, approximately 3.25 miles, returning to the beginning point...

27 CFR 9.222 - Naches Heights.

Code of Federal Regulations, 2014 CFR

2014-04-01

... the intersection of the Burlington Northern single-track rail line and the Congdon (Schuler) Canal... a straight line approximately 0.15 mile to the Congdon (Schuler) Canal, which closely parallels the... Congdon (Schuler) Canal, onto the Selah map, approximately 3.25 miles, returning to the beginning point...

27 CFR 9.222 - Naches Heights.

Code of Federal Regulations, 2013 CFR

2013-04-01

... the intersection of the Burlington Northern single-track rail line and the Congdon (Schuler) Canal... a straight line approximately 0.15 mile to the Congdon (Schuler) Canal, which closely parallels the... Congdon (Schuler) Canal, onto the Selah map, approximately 3.25 miles, returning to the beginning point...

The challenge of global water access monitoring: evaluating straight-line distance versus self-reported travel time among rural households in Mozambique.

PubMed

Ho, Jeff C; Russel, Kory C; Davis, Jennifer

2014-03-01

Support is growing for the incorporation of fetching time and/or distance considerations in the definition of access to improved water supply used for global monitoring. Current efforts typically rely on self-reported distance and/or travel time data that have been shown to be unreliable. To date, however, there has been no head-to-head comparison of such indicators with other possible distance/time metrics. This study provides such a comparison. We examine the association between both straight-line distance and self-reported one-way travel time with measured route distances to water sources for 1,103 households in Nampula province, Mozambique. We find straight-line, or Euclidean, distance to be a good proxy for route distance (R(2) = 0.98), while self-reported travel time is a poor proxy (R(2) = 0.12). We also apply a variety of time- and distance-based indicators proposed in the literature to our sample data, finding that the share of households classified as having versus lacking access would differ by more than 70 percentage points depending on the particular indicator employed. This work highlights the importance of the ongoing debate regarding valid, reliable, and feasible strategies for monitoring progress in the provision of improved water supply services.

An apparatus to estimate the hydrodynamic coefficients of autonomous underwater vehicles using water tunnel testing.

PubMed

Nouri, N M; Mostafapour, K; Bahadori, R

2016-06-01

Hydrodynamic coefficients or hydrodynamic derivatives of autonomous underwater vehicles (AUVs) play an important role in their development and maneuverability. The most popular way of estimating their coefficients is to implement captive model tests such as straight line tests and planar motion mechanism (PMM) tests in the towing tanks. This paper aims to develop an apparatus based on planar experiments of water tunnel in order to estimate hydrodynamic derivatives due to AUVs' acceleration and velocity. The capability of implementing straight line tests and PMM ones using mechanical oscillators located in the downstream flow of the model is considered in the design procedure of the system. The hydrodynamic derivatives that resulted from the acceleration and velocity of the AUV model were estimated using the apparatus that we developed. Static and dynamics test results were compared for the similar derivatives. The findings showed that the system provided the basis for conducting static tests, i.e., straight-line and dynamic tests that included pure pitch and pure heave. By conducting such tests in a water tunnel, we were able to eliminate errors related to the time limitation of the tests and the effects of surface waves in the towing tank on AUVs with applications in the deep sea.

Statistical Methods in Physical Oceanography: Proceedings of ’Aha Huliko’a Hawaiian Winter Workshop Held in Manoa, Hawaii on January 12-15, 1993

DTIC Science & Technology

1993-11-01

field X(t) at time 1. Ti. is the set of all times when both pi and pi have been observed and ni. is the number of elements in T Definition Eq. (22) is...termed contour analysis, for melding of oceanic data and for space-time interpolation of gappy frontal data sets . The key elements of contour analysis...plane and let fl(1) be the set of all straight lines intersecting F. Directly measuring the number of intersections between a random element W E 11(F) and

Document localization algorithms based on feature points and straight lines

NASA Astrophysics Data System (ADS)

Skoryukina, Natalya; Shemiakina, Julia; Arlazarov, Vladimir L.; Faradjev, Igor

2018-04-01

The important part of the system of a planar rectangular object analysis is the localization: the estimation of projective transform from template image of an object to its photograph. The system also includes such subsystems as the selection and recognition of text fields, the usage of contexts etc. In this paper three localization algorithms are described. All algorithms use feature points and two of them also analyze near-horizontal and near- vertical lines on the photograph. The algorithms and their combinations are tested on a dataset of real document photographs. Also the method of localization quality estimation is proposed that allows configuring the localization subsystem independently of the other subsystems quality.

Regenerative Engine Analysis Program (REAP).

DTIC Science & Technology

1981-01-01

Output Shaft Forged SAE 9310 Performance for the TSE Model 1071 is shown in Figures 41, 42, and 43 for static and flight conditions at three altitudes...Flange - Air Inlet 3 in. dia 2 0.72 Duct - Air Outlet, 3.25 in. OD 0.050 2 0.78 Flange - Air Outlet 3.25 in. dia 2 0.78 Weld and Miscellaneous -- 2.67... 4140 tubes, plus the outer case. (This assumes straight line trajectory with no tumbling.) This would result in leakage of nearly one percent of the

Pentzien lays diagonal cross of Potomac for Columbia gas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klinger, O.

1976-05-01

One of the most unusual pipeline river crossings was completed last fall by Pentzien, Inc., for Columbia LNG Corp. on the Potomac River at Bryans Road, MD, 22 miles south of Washington, DC. Part of a line delivering regasified Algerian LNG to Virginia and Pennsylvania, this crossing would have been only 7896 ft straight across the river; however, to obtaining necessary country authorization without excessively delaying the project, the line was laid diagonally 19,500 ft across the river at a cost about two-thirds more than for a straight-line crossing. The concrete-coated 36-in.-diam pipe for the project was so heavy thatmore » each transport truck could handle only a single 40-ft length at a time. Laser beams on each side of the river were used to guide both the dredging and pipelaying operations.« less

Estimates of ocean wave heights and attenuation in sea ice using the SAR wave mode on Sentinel-1A

NASA Astrophysics Data System (ADS)

Ardhuin, Fabrice; Collard, Fabrice; Chapron, Bertrand; Girard-Ardhuin, Fanny; Guitton, Gilles; Mouche, Alexis; Stopa, Justin E.

2015-04-01

Swell evolution from the open ocean into sea ice is poorly understood, in particular the amplitude attenuation expected from scattering and dissipation. New synthetic aperture radar (SAR) data from Sentinel-1A wave mode reveal intriguing patterns of bright oscillating lines shaped like instant noodles. We investigate cases in which the oscillations are in the azimuth direction, around a straight line in the range direction. This observation is interpreted as the distortion by the SAR processing of crests from a first swell, due to the presence of a second swell. Since deviations from a straight line should be proportional to the orbital velocity toward the satellite, swell height can be estimated, from 1.5 to 5 m in the present case. The evolution of this 13 s period swell across the ice pack is consistent with an exponential attenuation on a length scale of 200 km.

Estimates of ocean wave heights and attenuation in sea ice using the SAR wave mode on Sentinel-1A

NASA Astrophysics Data System (ADS)

Ardhuin, Fabrice; Collard, Fabrice; Chapron, Bertrand; Girard-Ardhuin, Fanny; Guitton, Gilles; Mouche, Alexis; Stopa, Justin

2015-04-01

Swell evolution from the open ocean into sea ice is poorly understood, in particular the amplitude attenuation expected from scattering and dissipation. New synthetic aperture radar (SAR) data from Sentinel-1 wave mode reveal intriguing patterns of bright oscillating lines shaped like instant noodles. We investigate cases in which the oscillations are in the azimuth direction, around a straight line in the range direction. This observation is interpreted as the distortion by the SAR processing of crests from a first swell, due to the presence of a second swell. As deviations from a straight line should be proportional to the orbital velocity towards the satellite, swell height can be estimated, from 1.5 to 5 m in the present case. This evolution of this 13 s period swell across the ice pack is consistent with an exponential attenuation on a length scale of 200 km.

27 CFR 9.89 - Umpqua Valley.

Code of Federal Regulations, 2010 CFR

2010-04-01

... in Township 21 South (T21S), Range 4 West (R4W) on the “Roseburg” map. (1) From the beginning point... range line R8W/R9W approximately 3.5 miles to its intersection with township line T22S/T23S; (4) Thence southeast approximately 8.5 miles along a straight line to the intersection of township line T23S/T24S with...

27 CFR 9.89 - Umpqua Valley.

Code of Federal Regulations, 2011 CFR

2011-04-01

... in Township 21 South (T21S), Range 4 West (R4W) on the “Roseburg” map. (1) From the beginning point... range line R8W/R9W approximately 3.5 miles to its intersection with township line T22S/T23S; (4) Thence southeast approximately 8.5 miles along a straight line to the intersection of township line T23S/T24S with...

Chymotrypsin effects on the determination of sperm parameters and seminal biochemistry markers.

PubMed

Chen, Fang; Lu, Jin-Chun; Xu, Hui-Ru; Huang, Yu-Feng; Lu, Nian-Qing

2006-01-01

Few reports of the effects of treatment with chymotrypsin on the determination of sperm parameters and seminal biochemistry markers are documented. Sperm parameters of 63 liquefied and 27 non-liquefied samples, untreated or treated with chymotrypsin, were evaluated using computer-assisted semen analysis. In addition, biochemistry markers such as gamma-glutamyltranspeptidase, alpha-glucosidase and fructose in 50 liquefied and 39 non-liquefied samples, untreated or treated with chymotrypsin, were determined. Treatment with chymotrypsin had no effect on sperm concentration, motility, motility a and b, straightness, curvilinear velocity, straight line velocity, average path velocity and beat cross frequency in both liquefied and non-liquefied semen. However, linearity (p=0.025) decreased and the amplitude of the lateral head (p=0.029) increased significantly in non-liquefied semen after treatment with chymotrypsin. The levels of gamma-glutamyltranspeptidase, alpha-glucosidase and fructose in seminal plasma were unaffected by chymotrypsin, regardless of liquefaction status. Chymotrypsin had no effects on the detection of sperm parameters and biochemistry markers, and could be used to treat non-liquefied samples before semen analysis in the andrology laboratory.

The straight line hypothesis elaborated: case reference obesity, an argument for acidosis, oxidative stress, and disease conglomeration?

PubMed

Berkemeyer, Shoma

2010-07-01

Studies report on the association between obesity and oxidative stress, with and without additional diseases. Macrophages in adipocytes, and hypoxia in adipose tissue have been suggested to explain how obesity can relate to oxidative stress. The straight line hypothesis using the lactic acid trap construct has been put forward to explain how proton imbalance can relate to obesity. Proton imbalance has been also reported to associate with the production of reactive oxygen species by inhibition of mitochondrial energy production. This review brings together existing literature and concepts to explain how obesity can relate to oxidative stress via protons, uniquely for itself or, as often observed, in conglomeration of additional diseases. Copyright 2010 Elsevier Ltd. All rights reserved.

Collision-free motion of two robot arms in a common workspace

NASA Technical Reports Server (NTRS)

Basta, Robert A.; Mehrotra, Rajiv; Varanasi, Murali R.

1987-01-01

Collision-free motion of two robot arms in a common workspace is investigated. A collision-free motion is obtained by detecting collisions along the preplanned trajectories using a sphere model for the wrist of each robot and then modifying the paths and/or trajectories of one or both robots to avoid the collision. Detecting and avoiding collisions are based on the premise that: preplanned trajectories of the robots follow a straight line; collisions are restricted to between the wrists of the two robots (which corresponds to the upper three links of PUMA manipulators); and collisions never occur between the beginning points or end points on the straight line paths. The collision detection algorithm is described and some approaches to collision avoidance are discussed.

A comparison of techniques for inversion of radio-ray phase data in presence of ray bending

NASA Technical Reports Server (NTRS)

Wallio, H. A.; Grossi, M. D.

1972-01-01

Derivations are presented of the straight-line Abel transform and the seismological Herglotz-Wiechert transform (which takes ray bending into account) that are used in the reconstruction of refractivity profiles from radio-wave phase data. Profile inversion utilizing these approaches, performed in computer-simulated experiments, are compared for cases of positive, zero, and negative ray bending. For thin atmospheres and ionospheres, such as the Martian atmosphere and ionosphere, radio wave signals are shown to be inverted accurately with both methods. For dense media, such as the solar corona or the lower Venus atmosphere, the refractive recovered by the seismological Herglotz-Wiechert transform provide a significant improvement compared with the straight-line Abel transform.

Straight talk new approaches in healthcare. The outpatient market: protect important market share.

PubMed

Broermann, Robert A; Kerner, Donald J; Walters, H Patrick; Hickman, Brett M

2003-10-27

Hospitals are facing competition from myriad freestanding players in the outpatient market. It's a fight hospitals can't afford to lose because they often use outpatient profits to cover losses in other service lines. Indeed about 60% of the average hospital's operating margin depends on outpatient revenues. In this session of Straight Talk, we examine how hospitals can build and finance outpatient services with physicians, increasing their competitiveness in increasingly competitive markets.

33 CFR 80.1142 - San Francisco Harbor, CA.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 1 2012-07-01 2012-07-01 false San Francisco Harbor, CA. 80.1142 Section 80.1142 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY INTERNATIONAL NAVIGATION RULES COLREGS DEMARCATION LINES Pacific Coast § 80.1142 San Francisco Harbor, CA. A straight line...

33 CFR 80.1142 - San Francisco Harbor, CA.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false San Francisco Harbor, CA. 80.1142 Section 80.1142 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY INTERNATIONAL NAVIGATION RULES COLREGS DEMARCATION LINES Pacific Coast § 80.1142 San Francisco Harbor, CA. A straight line...

33 CFR 80.1142 - San Francisco Harbor, CA.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 1 2011-07-01 2011-07-01 false San Francisco Harbor, CA. 80.1142 Section 80.1142 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY INTERNATIONAL NAVIGATION RULES COLREGS DEMARCATION LINES Pacific Coast § 80.1142 San Francisco Harbor, CA. A straight line...

33 CFR 80.1142 - San Francisco Harbor, CA.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 1 2014-07-01 2014-07-01 false San Francisco Harbor, CA. 80.1142 Section 80.1142 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY INTERNATIONAL NAVIGATION RULES COLREGS DEMARCATION LINES Pacific Coast § 80.1142 San Francisco Harbor, CA. A straight line...

33 CFR 80.1142 - San Francisco Harbor, CA.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 1 2013-07-01 2013-07-01 false San Francisco Harbor, CA. 80.1142 Section 80.1142 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY INTERNATIONAL NAVIGATION RULES COLREGS DEMARCATION LINES Pacific Coast § 80.1142 San Francisco Harbor, CA. A straight line...

Pattern Recognition by Retina-Like Devices.

ERIC Educational Resources Information Center

Weiman, Carl F. R.; Rothstein, Jerome

This study has investigated some pattern recognition capabilities of devices consisting of arrays of cooperating elements acting in parallel. The problem of recognizing straight lines in general position on the quadratic lattice has been completely solved by applying parallel acting algorithms to a special code for lines on the lattice. The…

33 CFR 80.1430 - Kaneohe Bay, Oahu, HI.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Kaneohe Bay, Oahu, HI. 80.1430 Section 80.1430 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY INTERNATIONAL NAVIGATION RULES COLREGS DEMARCATION LINES Pacific Islands § 80.1430 Kaneohe Bay, Oahu, HI. A straight line...

Perceived relative attractiveness of facial profiles with varying degrees of skeletal anomalies.

PubMed

Hönn, Mirjam; Dietz, Klaus; Godt, Arnim; Göz, Gernot

2005-05-01

The objective of this study was to answer the following questions: Are profiles of Class I patients perceived as more attractive than profiles of Class II or Class III patients in Germany today? How pronounced must a skeletal malocclusion be to be perceived as less attractive? Are there differences in perception between dentists and laypersons? For the present study we examined seven patients with skeletal Class I, orthognathic maxillae and mandibles, and straight average faces (ideal biometric face as defined by A. M. Schwarz). Using the Onyx Ceph software, their profile lines were modified to reflect three different Class II profile variants and three different Class III profile variants. The 49 profiles thus obtained were assigned to two groups. Group 1 comprised the seven straight average faces and the first part of the retrognathic and prognathic profile variants. Group 2 comprised the same seven straight average faces and the remaining retrognathic and prognathic profile variants. Both groups of faces were scored by 130 laypersons and 126 dentists. Both groups of observers perceived the seven straight average faces similarly both in the first and second (subsequent) scoring rounds. The straight average face was perceived as most attractive by laypersons (mean, 5.48; 95% confidence interval (CI:) 5.33-5.60) and dentists (mean, 5.44; 95% CI, 5.28-5.50) alike, followed by the mildest variant of the retrognathic face (laypersons, mean, 4.85; 95% CI, 4.68-5.01; dentists, mean, 4.98; 95% CI, 4.81-5.10). Dentists differentiated more clearly by degree of skeletal malocclusion than did laypersons. Both groups alike perceived the extreme variant of the prognathic and retrognathic profile lines as the least attractive. Grouping the subjects by gender yielded only minor differences in perception. The straight average face is perceived as most attractive by representative German populations today. Dentists make clearer gradual distinctions in their perceptions than do laypersons.

76 FR 38718 - Indiana Disaster #IN-00037

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-01

.../23/2011. Incident: Severe Storms, Tornadoes, Straight-line Winds, and Flooding. Incident Period: 04..., Spencer, Starke, Sullivan, Switzerland, Vanderburgh, Warrick, Washington. The Interest Rates are: Percent...

Flow analysis for efficient design of wavy structured microchannel mixing devices

NASA Astrophysics Data System (ADS)

Kanchan, Mithun; Maniyeri, Ranjith

2018-04-01

Microfluidics is a rapidly growing field of applied research which is strongly driven by demands of bio-technology and medical innovation. Lab-on-chip (LOC) is one such application which deals with integrating bio-laboratory on micro-channel based single fluidic chip. Since fluid flow in such devices is restricted to laminar regime, designing an efficient passive modulator to induce chaotic mixing for such diffusion based flow is a major challenge. In the present work two-dimensional numerical simulation of viscous incompressible flow is carried out using immersed boundary method (IBM) to obtain an efficient design for wavy structured micro-channel mixing devices. The continuity and Navier-Stokes equations governing the flow are solved by fractional step based finite volume method on a staggered Cartesian grid system. IBM uses Eulerian co-ordinates to describe fluid flow and Lagrangian co-ordinates to describe solid boundary. Dirac delta function is used to couple both these co-ordinate variables. A tether forcing term is used to impose the no-slip boundary condition on the wavy structure and fluid interface. Fluid flow analysis by varying Reynolds number is carried out for four wavy structure models and one straight line model. By analyzing fluid accumulation zones and flow velocities, it can be concluded that straight line structure performs better mixing for low Reynolds number and Model 2 for higher Reynolds number. Thus wavy structures can be incorporated in micro-channels to improve mixing efficiency.

27 CFR 9.213 - Snipes Mountain.

Code of Federal Regulations, 2014 CFR

2014-04-01

... beginning point, proceed south along the eastern boundary of section 34 for less than 0.1 mile to its intersection with the 750-foot elevation line, T10N, R22E; then (2) Proceed along the 750-foot elevation line... boundary of section 27, T10N, R21E; then (4) Proceed north in a straight line for less than 0.1 mile to the...

27 CFR 9.213 - Snipes Mountain.

Code of Federal Regulations, 2011 CFR

2011-04-01

... beginning point, proceed south along the eastern boundary of section 34 for less than 0.1 mile to its intersection with the 750-foot elevation line, T10N, R22E; then (2) Proceed along the 750-foot elevation line... boundary of section 27, T10N, R21E; then (4) Proceed north in a straight line for less than 0.1 mile to the...

27 CFR 9.213 - Snipes Mountain.

Code of Federal Regulations, 2012 CFR

2012-04-01

... beginning point, proceed south along the eastern boundary of section 34 for less than 0.1 mile to its intersection with the 750-foot elevation line, T10N, R22E; then (2) Proceed along the 750-foot elevation line... boundary of section 27, T10N, R21E; then (4) Proceed north in a straight line for less than 0.1 mile to the...

27 CFR 9.213 - Snipes Mountain.

Code of Federal Regulations, 2010 CFR

2010-04-01

... beginning point, proceed south along the eastern boundary of section 34 for less than 0.1 mile to its intersection with the 750-foot elevation line, T10N, R22E; then (2) Proceed along the 750-foot elevation line... boundary of section 27, T10N, R21E; then (4) Proceed north in a straight line for less than 0.1 mile to the...

27 CFR 9.213 - Snipes Mountain.

Code of Federal Regulations, 2013 CFR

2013-04-01

... beginning point, proceed south along the eastern boundary of section 34 for less than 0.1 mile to its intersection with the 750-foot elevation line, T10N, R22E; then (2) Proceed along the 750-foot elevation line... boundary of section 27, T10N, R21E; then (4) Proceed north in a straight line for less than 0.1 mile to the...

75 FR 45679 - Oklahoma Disaster #OK-00043

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-03

.../26/2010. Incident: Severe Storms, Tornadoes, Straight-line Winds, and Flooding. Incident Period: 06...: Primary Counties: Beaver, Cimarron, Lincoln, Logan, Major, Oklahoma, Texas. The Interest Rates are...

The effect of ankle bracing on knee kinetics and kinematics during volleyball-specific tasks.

PubMed

West, T; Ng, L; Campbell, A

2014-12-01

The purpose of this study was to examine the effects of ankle bracing on knee kinetics and kinematics during volleyball tasks. Fifteen healthy, elite, female volleyball players performed a series of straight-line and lateral volleyball tasks with no brace and when wearing an ankle brace. A 14-camera Vicon motion analysis system and AMTI force plate were used to capture the kinetic and kinematic data. Knee range of motion, peak knee anterior-posterior and medial-lateral shear forces, and peak ground reaction forces that occurred between initial contact with the force plate and toe off were compared using paired sample t-tests between the braced and non-braced conditions (P < 0.05). The results revealed no significant effect of bracing on knee kinematics or ground reaction forces during any task or on knee kinetics during the straight-line movement volleyball tasks. However, ankle bracing was demonstrated to reduce knee lateral shear forces during all of the lateral movement volleyball tasks. Wearing the Active Ankle T2 brace will not impact knee joint range of motion and may in fact reduce shear loading to the knee joint in volleyball players. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Complexity and approximability for a problem of intersecting of proximity graphs with minimum number of equal disks

NASA Astrophysics Data System (ADS)

Kobylkin, Konstantin

2016-10-01

Computational complexity and approximability are studied for the problem of intersecting of a set of straight line segments with the smallest cardinality set of disks of fixed radii r > 0 where the set of segments forms straight line embedding of possibly non-planar geometric graph. This problem arises in physical network security analysis for telecommunication, wireless and road networks represented by specific geometric graphs defined by Euclidean distances between their vertices (proximity graphs). It can be formulated in a form of known Hitting Set problem over a set of Euclidean r-neighbourhoods of segments. Being of interest computational complexity and approximability of Hitting Set over so structured sets of geometric objects did not get much focus in the literature. Strong NP-hardness of the problem is reported over special classes of proximity graphs namely of Delaunay triangulations, some of their connected subgraphs, half-θ6 graphs and non-planar unit disk graphs as well as APX-hardness is given for non-planar geometric graphs at different scales of r with respect to the longest graph edge length. Simple constant factor approximation algorithm is presented for the case where r is at the same scale as the longest edge length.

Comparison of geographic methods to assess travel patterns of persons diagnosed with HIV in Philadelphia: how close is close enough?

PubMed

Eberhart, Michael G; Share, Amanda M; Shpaner, Mark; Brady, Kathleen A

2015-02-01

Travel distance to medical care has been assessed using a variety of geographic methods. Network analyses are less common, but may generate more accurate estimates of travel costs. We compared straight-line distances and driving distance, as well as average drive time and travel time on a public transit network for 1789 persons diagnosed with HIV between 2010 and 2012 to identify differences overall, and by distinct geographic areas of Philadelphia. Paired t-tests were used to assess differences across methods, and analysis of variance was used to assess between-group differences. Driving distances were significantly longer than straight-line distances (p<0.001) and transit times were significantly longer than driving times (p<0.001). Persons living in the northeast section of the city traveled greater distances, and at greater cost of time and effort, than persons in all other areas of the city (p<0.001). Persons living in the northwest section of the city traveled farther and longer than all other areas except the northeast (p<0.0001). Network analyses that include public transit will likely produce a more realistic estimate of the travel costs, and may improve models to predict medical care outcomes. Copyright © 2014 Elsevier Inc. All rights reserved.

Gate line edge roughness amplitude and frequency variation effects on intra die MOS device characteristics

NASA Astrophysics Data System (ADS)

Hamadeh, Emad; Gunther, Norman G.; Niemann, Darrell; Rahman, Mahmud

2006-06-01

Random fluctuations in fabrication process outcomes such as gate line edge roughness (LER) give rise to corresponding fluctuations in scaled down MOS device characteristics. A thermodynamic-variational model is presented to study the effects of LER on threshold voltage and capacitance of sub-50 nm MOS devices. Conceptually, we treat the geometric definition of the MOS devices on a die as consisting of a collection of gates. In turn, each of these gates has an area, A, and a perimeter, P, defined by nominally straight lines subject to random process outcomes producing roughness. We treat roughness as being deviations from straightness consisting of both transverse amplitude and longitudinal wavelength each having lognormal distribution. We obtain closed-form expressions for variance of threshold voltage ( Vth), and device capacitance ( C) at Onset of Strong Inversion (OSI) for a small device. Using our variational model, we characterized the device electrical properties such as σ and σC in terms of the statistical parameters of the roughness amplitude and spatial frequency, i.e., inverse roughness wavelength. We then verified our model with numerical analysis of Vth roll-off for small devices and σ due to dopant fluctuation. Our model was also benchmarked against TCAD of σ as a function of LER. We then extended our analysis to predict variations in σ and σC versus average LER spatial frequency and amplitude, and oxide-thickness. Given the intuitive expectation that LER of very short wavelengths must also have small amplitude, we have investigated the case in which the amplitude mean is inversely related to the frequency mean. We compare with the situation in which amplitude and frequency mean are unrelated. Given also that the gate perimeter may consist of different LER signature for each side, we have extended our analysis to the case when the LER statistical difference between gate sides is moderate, as well as when it is significantly large.

Seeing a straight line on a curved surface: decoupling of patterns from surfaces by single IT neurons

PubMed Central

Ratan Murty, N. Apurva

2016-01-01

We have no difficulty seeing a straight line drawn on a paper even when the paper is bent, but this inference is in fact nontrivial. Doing so requires either matching local features or representing the pattern after factoring out the surface shape. Here we show that single neurons in the monkey inferior temporal (IT) cortex show invariant responses to patterns across rigid and nonrigid changes of surfaces. We recorded neuronal responses to stimuli in which the pattern and the surrounding surface were varied independently. In a subset of neurons, we found pattern-surface interactions that produced similar responses to stimuli across congruent pattern and surface transformations. These interactions produced systematic shifts in curvature tuning of patterns when overlaid on convex and flat surfaces. Our results show that surfaces are factored out of patterns by single neurons, thereby enabling complex perceptual inferences. NEW & NOTEWORTHY We have no difficulty seeing a straight line on a curved piece of paper, but in fact, doing so requires decoupling the shape of the surface from the pattern itself. Here we report a novel form of invariance in the visual cortex: single neurons in monkey inferior temporal cortex respond similarly to congruent transformations of patterns and surfaces, in effect decoupling patterns from the surface on which they are overlaid. PMID:27733595

27 CFR 9.204 - Tracy Hills.

Code of Federal Regulations, 2012 CFR

2012-04-01

... miles generally northwest along the meandering 500-foot elevation line to section 18, T4S/R6E, where the... point, proceed 0.4 mile generally southeast along the Delta-Mendota Canal to its intersection with the...) Proceed 5.6 miles straight east along the Western Pacific Railway line and then along Linne Road to the...

27 CFR 9.204 - Tracy Hills.

Code of Federal Regulations, 2014 CFR

2014-04-01

... miles generally northwest along the meandering 500-foot elevation line to section 18, T4S/R6E, where the... point, proceed 0.4 mile generally southeast along the Delta-Mendota Canal to its intersection with the...) Proceed 5.6 miles straight east along the Western Pacific Railway line and then along Linne Road to the...

27 CFR 9.204 - Tracy Hills.

Code of Federal Regulations, 2013 CFR

2013-04-01

... miles generally northwest along the meandering 500-foot elevation line to section 18, T4S/R6E, where the... point, proceed 0.4 mile generally southeast along the Delta-Mendota Canal to its intersection with the...) Proceed 5.6 miles straight east along the Western Pacific Railway line and then along Linne Road to the...

27 CFR 9.204 - Tracy Hills.

Code of Federal Regulations, 2011 CFR

2011-04-01

... miles generally northwest along the meandering 500-foot elevation line to section 18, T4S/R6E, where the... point, proceed 0.4 mile generally southeast along the Delta-Mendota Canal to its intersection with the...) Proceed 5.6 miles straight east along the Western Pacific Railway line and then along Linne Road to the...

Controller Requirements for Uncoupled Aircraft Motion. Volume 1

DTIC Science & Technology

1984-09-01

the nose down to the run-in line, followed by roll- out into a straight line dive. Well learned precognitive maneuvers do not nvolve much psychomotor...This is initially a precognitive transient track- ing maneuver, fo’llowed by maintaining a constant, safe g level until a desired ra e of climb- is

27 CFR 9.38 - Cienega Valley.

Code of Federal Regulations, 2010 CFR

2010-04-01

... southeast portion of Section 21, Township 14 South, Range 6 East. (1) From the beginning point, the boundary... Township 14 South, Range 6 East, Section 21; (2) Thence in a straight line to the southwest portion of Section 28, Township 14 South, Range 6 East, where the 1400-foot contour line intersects the south border...

27 CFR 9.38 - Cienega Valley.

Code of Federal Regulations, 2011 CFR

2011-04-01

... southeast portion of Section 21, Township 14 South, Range 6 East. (1) From the beginning point, the boundary... Township 14 South, Range 6 East, Section 21; (2) Thence in a straight line to the southwest portion of Section 28, Township 14 South, Range 6 East, where the 1400-foot contour line intersects the south border...

Geometric Lie algebra in matter, arts and mathematics with incubation of the periodic systems of the elements

NASA Astrophysics Data System (ADS)

Trell, Erik; Edeagu, Samuel; Animalu, Alexander

2017-01-01

From a brief recapitulation of the foundational works of Marius Sophus Lie and Herrmann Günther Grassmann, and including missing African links, a rhapsodic survey is made of the straight line of extension and existence that runs as the very fibre of generation and creation throughout Nature's all utterances, which must therefore ultimately be the web of Reality itself of which the Arts and Sciences are interpreters on equal explorer terms. Assuming their direct approach, the straight line and its archaic and algebraic and artistic bearings and convolutions have been followed towards their inner reaches, which earlier resulted in a retrieval of the baryon and meson elementary particles and now equally straightforward the electron geodesics and the organic build of the periodic system of the elements.

Application and Analysis of the Isoelectronic Line Ratio Temperature Diagnostic in a Planar Ablating-Plasma Experiment at the National Ignition Facility

NASA Astrophysics Data System (ADS)

Epstein, R.; Rosenberg, M. J.; Solodov, A. A.; Myatt, J. F.; Regan, S. P.; Seka, W.; Hohenberger, M.; Barrios, M. A.; Moody, J. D.

2015-11-01

The Mn/Co isoelectronic emission-line ratio from a microdot source in planar CH foil targets was measured to infer the electron temperature (Te) in the ablating plasma during two-plasmon-decay experiments at the National Ignition Facility (NIF). We examine the systematic uncertainty in the Te estimate based on the temperature and density sensitivities of the line ratio in conjunction with plausible density constraints, and its contribution to the total Te estimate uncertainty. The potential advantages of alternative microdot elements (e.g., Ti/Cr and Sc/V) are considered. The microdot mass was selected to provide ample line strength while minimizing the effect of self-absorption on the line emission, which is of particular concern, given the narrow linewidths of mid- Z emitters at subcritical electron densities. Atomic line-formation theory and detailed atomic-radiative simulations show that the straight forward interpretation of the isoelectronic ratio solely in terms of its temperature independence remains valid with lines of moderate optical thickness (up to ~ 10) at line center. This material is based upon work supported by the Department of Energy National Nuclear Security Administration under Award Number DE-NA0001944.

Preliminary test results from a telescope of Hughes pixel arrays at FNAL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jernigan, J.G.; Arens, J.; Vezie, D.

1992-09-01

In December of 1991 three silicon hybrid pixel detectors each having 2.56 [times] 2.56 pixels 30 [mu]m square, made by the Hughes Aircraft Company, were placed in a high energy muon beam at the Fermi National Accelerator Laboratory. Straight tracks were recorded in these detectors at angles to the normal to the plane of the silicon ranging from 0 to 45[degrees]. In this note, preliminary results are presented on the straight through tracks, i.e., those passing through the telescope at normal incidence. Pulse height data, signal-to-noise data, and preliminary straight line fits to the data resulting in residual distributions aremore » presented. Preliminary calculations show spatial resolution of less than 5 [mu]m in two dimensions.« less

Preliminary test results from a telescope of Hughes pixel arrays at FNAL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jernigan, J.G.; Arens, J.; Vezie, D.

1992-09-01

In December of 1991 three silicon hybrid pixel detectors each having 2.56 {times} 2.56 pixels 30 {mu}m square, made by the Hughes Aircraft Company, were placed in a high energy muon beam at the Fermi National Accelerator Laboratory. Straight tracks were recorded in these detectors at angles to the normal to the plane of the silicon ranging from 0 to 45{degrees}. In this note, preliminary results are presented on the straight through tracks, i.e., those passing through the telescope at normal incidence. Pulse height data, signal-to-noise data, and preliminary straight line fits to the data resulting in residual distributions aremore » presented. Preliminary calculations show spatial resolution of less than 5 {mu}m in two dimensions.« less

27 CFR 9.186 - Niagara Escarpment.

Code of Federal Regulations, 2012 CFR

2012-04-01

... Road, then north on Kayner Road 0.65 mile to its junction with the 600-foot contour line; then (12...) Proceed north along the east bank of the Niagara River about 0.6 mile to the northern boundary of the... about 0.8 mile to the park's northeast corner, and continue east in a straight line a short distance to...

27 CFR 9.178 - Columbia Gorge.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Quadrangle, Washington—Oregon, 1994; (6) Brown Creek Quadrangle, Oregon, 1994; (7) Ketchum Reservoir... straight south on the R12E-R13E line, crossing onto the Brown Creek map, to its intersection with the T1N-T1S Base Line at the southeast corner of section 36 (Brown Creek Quadrangle); (19) Continues 6.1 miles...

Modeling the size-density relationship in direct-seeded slash pine stands

Treesearch

Quang V. Cao; Thomas J. Dean; V. Clark Baldwin

2000-01-01

The relationship between quadratic mean diameter and tree density appeared curvilinear on a log–log scale, based on data from direct-seeded slash pine (Pinus elliotti var. elliotti Engelm.) stands. The self-thinning trajectory followed a straight line for high tree density levels and then turned away from this line as tree density...

75 FR 45648 - Oklahoma; Major Disaster and Related Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-03

... areas of the State of Oklahoma resulting from severe storms, tornadoes, straight-line winds, and..., Logan, Major, Oklahoma, and Texas Counties for Public Assistance. All counties within the State of...

Reading the Rover Tracks

NASA Image and Video Library

2012-08-29

The straight lines in Curiosity zigzag track marks are Morse code for JPL. The footprint is an important reference mark that the rover can use to drive more precisely via a system called visual odometry.

76 FR 44028 - Indiana; Major Disaster and Related Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-22

..., and straight line winds occurring on April 19, 2011, and April 22 to May 2, 2011, and flooding..., Starke, Sullivan, Switzerland, Vanderburgh, Warrick, and Washington Counties for Public Assistance. All...

Optimal placement of a brachioplasty scar: a survey evaluation.

PubMed

Samra, Salem; Samra, Fares; Liu, Yuen-Jong; Sawh-Martinez, Rajendra; Persing, John

2013-10-01

Brachioplasty has become a popular procedure to rejuvenate the upper arm, with its frequency increasing proportionately to the popularity of surgical weight loss procedures. The major complication of the procedure is undesirable, visible scarring. An ongoing, unresolved debate in the brachioplasty literature is the optimal placement of the brachioplasty scar. Some authors advocate a medially based incision along the bicipital groove, whereas others prefer to leave the scar posteriorly in the brachial sulcus. In addition, some advocate a sinusoidal scar over a straight-line closure. This study attempts to resolve the question of where and how to place the scar based on population surveys. Photographs were taken of a model with her arm progressively abducted at the shoulder to a level of 90 degrees, with the elbow progressively flexed to 90 degrees and the arm externally rotated. Anterior and posterior views were included. Using Photoshop, a brachioplasty scar was digitally created and placed on the arm first medially in the bicipital groove, then posteriorly in the brachial sulcus. Straight-line scars and sinusoidal scars were also compared in each position. Before creating a computer-generated image of the scars, the scar lines were marked with a marking pen to ensure they could be followed with movement of the model's arm. An online survey was then created and distributed and included multiple variables: position of the scar, length of scar vs residual deformity, and acceptability based on phase of scar in time (early vs late result). The scale was numerical from 1 to 5, with 1 being a very objectionable scar and 5 being a very acceptable scar. The survey was disseminated among the general public, plastic surgeons, and patients in the Yale Cosmetic Surgery Resident Clinic who were either seen in consultation for brachioplasty or who underwent the procedure. Electronic surveys were distributed to and completed by the general public (n = 117), local plastic surgery residents and attendings (n = 10), and patients who had undergone or were seen in consultation for brachioplasty (n = 9). Among all participants, in the chronic phase, a medial straight scar received an average rating of 4.00, a posterior straight scar received an average rating of 3.14, a posterior sinusoidal scar received an average rating of 2.61, and a medial sinusoidal scar received an average rating of 2.03. Across age groups, gender, plastic surgeons, and patients, the medially based straight brachioplasty scar is more acceptable than the posteriorly based straight scar (4.00 vs 3.14, P < 0.001). If the scar shape is made sinusoidal, a posteriorly based scar is favored over a medial one (2.61 vs 2.03, P < 0.001), yet this is still not as aesthetically pleasing as a medial straight scar (4.00 vs 2.61, P < 0.001). Furthermore, survey participants accepted a longer scar over a residual deformity (58.8% vs 41.2%). Based on the preferences of the populations surveyed, we conclude that the medially based straight scar is the most aesthetically acceptable option when performing a brachioplasty.

27 CFR 9.214 - Haw River Valley.

Code of Federal Regulations, 2011 CFR

2011-04-01

... significance. (b) Approved maps. The two United States Geological Survey 1:100,000-scale metric topographic... boundary line with Lynch Creek, southeast of Corbett and the Corbett Ridge, and then proceed in a straight...

27 CFR 9.138 - Benmore Valley.

Code of Federal Regulations, 2011 CFR

2011-04-01

....” (b) Approved Maps. The appropriate maps for determining the boundaries of the Benmore Valley... northeast in a straight line to the easternmost peak of an unnamed ridge with four peaks in the center of...

27 CFR 9.138 - Benmore Valley.

Code of Federal Regulations, 2010 CFR

2010-04-01

....” (b) Approved Maps. The appropriate maps for determining the boundaries of the Benmore Valley... northeast in a straight line to the easternmost peak of an unnamed ridge with four peaks in the center of...

27 CFR 9.78 - Ohio River Valley.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Valley.” (b) Approved maps. The approved maps for determining the boundary of the Ohio River Valley... boundary proceeds in a straight line westerly to the town of Dry Ridge in Grant County, Kentucky...

76 FR 33805 - Tennessee Disaster Number TN-00055

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-09

... State of Tennessee (FEMA-1979-DR), dated 05/09/2011. Incident: Severe Storms, Tornadoes, Straight-line, Winds, and Flooding. Incident Period: 04/19/2011 and continuing. Effective Date: 06/01/2011. Physical...

76 FR 72020 - Missouri Disaster #MO-00051

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-21

... Administrative declaration of a disaster for the State of Missouri dated 11/09/2011. Incident: Severe storms, straight line winds, tornadoes and flooding. Incident Period: 06/26/2011 through 06/27/2011. Effective Date...

76 FR 32983 - Tennessee; Major Disaster and Related Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-07

... areas of the State of Tennessee resulting from severe storms, tornadoes, straight line winds, and... program in the designated areas, Hazard Mitigation throughout the State, and any other forms of assistance...

76 FR 32984 - Mississippi; Major Disaster and Related Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-07

... certain areas of the State of Mississippi resulting from severe storms, tornadoes, straight- line winds..., and any other forms of assistance under the Stafford Act that you deem appropriate subject to...

Non-hoop winding effect on bonding temperature of laser assisted tape winding process

NASA Astrophysics Data System (ADS)

Zaami, Amin; Baran, Ismet; Akkerman, Remko

2018-05-01

One of the advanced methods for production of thermoplastic composite methods is laser assisted tape winding (LATW). Predicting the temperature in LATW process is very important since the temperature at nip-point (bonding line through width) plays a pivotal role in a proper bonding and hence the mechanical performance. Despite the hoop-winding where the nip-point is the straight line, non-hoop winding includes a curved nip-point line. Hence, the non-hoop winding causes somewhat a different power input through laser-rays and-reflections and consequently generates unknown complex temperature profile on the curved nip-point line. Investigating the temperature at the nip-point line is the point of interest in this study. In order to understand this effect, a numerical model is proposed to capture the effect of laser-rays and their reflections on the nip-point temperature. To this end, a 3D optical model considering the objects in LATW process is considered. Then, the power distribution (absorption and reflection) from the optical analysis is used as an input (heat flux distribution) for the thermal analysis. The thermal analysis employs a fully-implicit advection-diffusion model to calculate the temperature on the surfaces. The results are examined to demonstrate the effect of winding direction on the curved nip-point line (tape width) which has not been considered in literature up to now. Furthermore, the results can be used for designing a better and more efficient setup in the LATW process.

Three-dimensional finite-element analysis of chevron-notched fracture specimens

NASA Technical Reports Server (NTRS)

Raju, I. S.; Newman, J. C., Jr.

1984-01-01

Stress-intensity factors and load-line displacements were calculated for chevron-notched bar and rod fracture specimens using a three-dimensional finite-element analysis. Both specimens were subjected to simulated wedge loading (either uniform applied displacement or uniform applied load). The chevron-notch sides and crack front were assumed to be straight. Crack-length-to-specimen width ratios (a/w) ranged from 0.4 to 0.7. The width-to-thickness ratio (w/B) was 1.45 or 2. The bar specimens had a height-to-width ratio of 0.435 or 0.5. Finite-element models were composed of singularity elements around the crack front and 8-noded isoparametric elements elsewhere. The models had about 11,000 degrees of freedom. Stress-intensity factors were calculated by using a nodal-force method for distribution along the crack front and by using a compliance method for average values. The stress intensity factors and load-line displacements are presented and compared with experimental solutions from the literature. The stress intensity factors and load-line displacements were about 2.5 and 5 percent lower than the reported experimental values, respectively.

Measuring (subglacial) bedform orientation, length, and longitudinal asymmetry - Method assessment.

PubMed

Jorge, Marco G; Brennand, Tracy A

2017-01-01

Geospatial analysis software provides a range of tools that can be used to measure landform morphometry. Often, a metric can be computed with different techniques that may give different results. This study is an assessment of 5 different methods for measuring longitudinal, or streamlined, subglacial bedform morphometry: orientation, length and longitudinal asymmetry, all of which require defining a longitudinal axis. The methods use the standard deviational ellipse (not previously applied in this context), the longest straight line fitting inside the bedform footprint (2 approaches), the minimum-size footprint-bounding rectangle, and Euler's approximation. We assess how well these methods replicate morphometric data derived from a manually mapped (visually interpreted) longitudinal axis, which, though subjective, is the most typically used reference. A dataset of 100 subglacial bedforms covering the size and shape range of those in the Puget Lowland, Washington, USA is used. For bedforms with elongation > 5, deviations from the reference values are negligible for all methods but Euler's approximation (length). For bedforms with elongation < 5, most methods had small mean absolute error (MAE) and median absolute deviation (MAD) for all morphometrics and thus can be confidently used to characterize the central tendencies of their distributions. However, some methods are better than others. The least precise methods are the ones based on the longest straight line and Euler's approximation; using these for statistical dispersion analysis is discouraged. Because the standard deviational ellipse method is relatively shape invariant and closely replicates the reference values, it is the recommended method. Speculatively, this study may also apply to negative-relief, and fluvial and aeolian bedforms.

Dispersal of potato cyst nematodes measured using historical and spatial statistical analyses.

PubMed

Banks, N C; Hodda, M; Singh, S K; Matveeva, E M

2012-06-01

Rates and modes of dispersal of potato cyst nematodes (PCNs) were investigated. Analysis of records from eight countries suggested that PCNs spread a mean distance of 5.3 km/year radially from the site of first detection, and spread 212 km over ≈40 years before detection. Data from four countries with more detailed histories of invasion were analyzed further, using distance from first detection, distance from previous detection, distance from nearest detection, straight line distance, and road distance. Linear distance from first detection was significantly related to the time since the first detection. Estimated rate of spread was 5.7 km/year, and did not differ statistically between countries. Time between the first detection and estimated introduction date varied between 0 and 20 years, and differed among countries. Road distances from nearest and first detection were statistically significantly related to time, and gave slightly higher estimates for rate of spread of 6.0 and 7.9 km/year, respectively. These results indicate that the original site of introduction of PCNs may act as a source for subsequent spread and that this may occur at a relatively constant rate over time regardless of whether this distance is measured by road or by a straight line. The implications of this constant radial rate of dispersal for biosecurity and pest management are discussed, along with the effects of control strategies.

Assessment of repeatability of a wireless, inertial sensor-based lameness evaluation system for horses.

PubMed

Keegan, Kevin G; Kramer, Joanne; Yonezawa, Yoshiharu; Maki, Hiromitchi; Pai, P Frank; Dent, Eric V; Kellerman, Thomas E; Wilson, David A; Reed, Shannon K

2011-09-01

To determine repeatability of a wireless, inertial sensor-based lameness evaluation system in horses. 236 horses. Horses were from 2 to 29 years of age and of various breeds and lameness disposition. All horses were instrumented with a wireless, inertial sensor-based motion analysis system on the head (accelerometer), pelvis (midline croup region [accelerometer]), and right forelimb (gyroscope) before evaluation in 2 consecutive trials, approximately 5 minutes apart, as the horse was trotted in a straight line. Signal-processing algorithms generated overall trial asymmetry measures for vertical head and pelvic movement and stride-by-stride differences in head and pelvic maximum and minimum positions between right and left sides of each stride. Repeatability was determined, and trial difference was determined for groups of horses with various numbers of strides for which data were collected per trial. Inertial sensor-based measures of torso movement asymmetry were repeatable. Repeatability for measures of torso asymmetry for determination of hind limb lameness was slightly greater than that for forelimb lameness. Collecting large numbers of strides degraded stride-to-stride repeatability but did not degrade intertrial repeatability. The inertial sensor system used to measure asymmetry of head and pelvic movement as an aid in the detection and evaluation of lameness in horses trotting in a straight line was sufficiently repeatable to investigate for clinical use.

Optical or mechanical aids to drawing in the early Renaissance? A geometric analysis of the trellis work in Robert Campin's Mérode Altarpiece

NASA Astrophysics Data System (ADS)

Kulkarni, Ashutosh; Stork, David G.

2009-02-01

A recent theory claims that some Renaissance artists, as early as 1425, secretly traced optically projected images during the execution of some passages in some of their works, nearly a quarter millennium before historians of art and of optics have secure evidence anyone recorded an image this way. Key evidence adduced by the theory's proponents includes the trelliswork in the right panel of Robert Campin's Merode altarpiece triptych (c. 1425-28). If their claim were verified for this work, such a discovery would be extremely important to the history of art and of image making more generally: the Altarpiece would be the earliest surviving image believed to record the projected image of an illuminated object, the first step towards photography, over 400 years later. The projection theory proponents point to teeny "kinks" in the depicted slats of one orientation in the Altarpiece as evidence that Campin refocussed a projector twice and traced images of physically straight slats in his studio. However, the proponents rotated the digital images of each slat individually, rather than the full trelliswork as a whole, and thereby disrupted the relative alignment between the images of the kinks and thus confounded their analysis. We found that when properly rotated, the kinks line up nearly perfectly and are consistent with Campin using a subtly kinked straightedge repeatedly, once for each of the slats. Moreover, the proponents did not report any analysis of the other set of slats-the ones nearly perpendicular to the first set. These perpendicular slats are straight across the break line of the first set-an unlikely scenario in the optical explanation. Finally, whereas it would have been difficult for Campin to draw the middle portions of the slats perfectly straight by tracing a projected image, it would have been trivially simple had he used a straightedge. Our results and the lack of any contemporaneous documentary evidence for the projection technique imply that Campin used a simple mechanical aid-such as a minutely kinked straightedge or a mahl stick commonly used in the early Renaissance-rather than a very complex optical projector and procedure, undocumented from that time.

A Comparison of Best Fit Lines for Data with Outliers

ERIC Educational Resources Information Center

Glaister, P.

2005-01-01

Three techniques for determining a straight line fit to data are compared. The methods are applied to a range of datasets containing one or more outliers, and to a specific example from the field of chemistry. For the method which is the most resistant to the presence of outliers, a Microsoft Excel spreadsheet, as well as two Matlab routines, are…

Experiment Pamir-3. Coplanar emission of high energy gamma-quanta at interaction of hadrons with nuclei of air atoms at energies above 10 to the 7th power GeV

NASA Technical Reports Server (NTRS)

Asatiani, T. L.; Genina, L. E.; Zatsepin, G. T.

1985-01-01

A systematic analysis of large gamma families, detected in X-ray emulsion chambers, cases of multicore halos have been observed, and among them five events in which the halo is divided into three of four separate cores with their alignment observed in the target diagram (coplanarity of axes of corresponding electron photon cascades). The halo alignment (tendency to the straight line) leads to the aximuthal asymmetry (thrust). The analysis of lateral and momentum distributions of particles in these families shows that they also have thrust that correlates with the direction of the halo core alignment.

78 FR 72919 - Illinois; Major Disaster and Related Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-04

..., straight-line winds, and tornadoes on November 17, 2013, is of sufficient severity and magnitude to warrant... Needs Assistance will be limited to 75 percent of the total eligible costs. Further, you are authorized...

77 FR 60003 - New Jersey Disaster #NJ-00031

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-01

... Administrative declaration of a disaster for the State of New Jersey dated 09/21/2012. Incident: Severe Storms and significant Straight-line Winds. Incident Period: 06/30/2012. Effective Date: 09/21/2012. Physical...

76 FR 32982 - Alabama; Major Disaster and Related Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-07

... certain areas of the State of Alabama resulting from severe storms, tornadoes, straight-line winds, and... throughout the State, and any other forms of assistance under the Stafford Act that you deem appropriate...

76 FR 32985 - Georgia; Major Disaster and Related Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-07

... certain areas of the State of Georgia resulting from severe storms, tornadoes, straight line winds, and... State, and any other forms of assistance under the Stafford Act that you deem appropriate subject to...

76 FR 78342 - Proposed Collection; Comment Request for Notice 2011-65

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-16

... housing relief needed as a result of the devastation caused by severe storms, tornadoes, straight-line... information on respondents, including through the use of automated collection techniques or other forms of...

75 FR 68848 - North Carolina Disaster Number NC-00030

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-09

...), dated 10/14/2010. Incident: Severe Storms, Flooding, and Straight-line Winds associated with remnants of Tropical Storm Nicole. Incident Period: 09/27/2010 through 10/01/2010. DATES: Effective Date: 11/01/2010...

40 CFR 86.125-94 - Methane analyzer calibration.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... Additional calibration points may be generated. For each range calibrated, if the deviation from a least-squares best-fit straight line is 2 percent or less of the value at each data point, concentration values...

40 CFR 86.125-94 - Methane analyzer calibration.

Code of Federal Regulations, 2014 CFR

2014-07-01

.... Additional calibration points may be generated. For each range calibrated, if the deviation from a least-squares best-fit straight line is 2 percent or less of the value at each data point, concentration values...

40 CFR 86.125-94 - Methane analyzer calibration.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... Additional calibration points may be generated. For each range calibrated, if the deviation from a least-squares best-fit straight line is 2 percent or less of the value at each data point, concentration values...

Percolation characteristics of solvent invasion in rough fractures under miscible conditions

NASA Astrophysics Data System (ADS)

Korfanta, M.; Babadagli, T.; Develi, K.

2017-10-01

Surface roughness and flow rate effects on the solvent transport under miscible conditions in a single fracture are studied. Surface replicas of seven different rocks (marble, granite, and limestone) are used to represent different surface roughness characteristics each described by different mathematical models including three fractal dimensions. Distribution of dyed solvent is investigated at various flow rate conditions to clarify the effect of roughness on convective and diffusive mixing. After a qualitative analysis using comparative images of different rocks, the area covered by solvent with respect to time is determined to conduct a semi-quantitative analysis. In this exercise, two distinct zones are identified, namely the straight lines obtained for convective (early times) and diffusive (late times) flow. The bending point between these two lines is used to point the transition between the two zones. Finally, the slopes of the straight lines and the bending points are correlated to five different roughness parameters and the rate (Peclet number). It is observed that both surface roughness and flow rate have significant effect on solvent spatial distribution. The largest area covered is obtained at moderate flow rates and hence not only the average surface roughness characteristic is important, but coessentially total fracture surface area needs to be considered when evaluating fluid distribution. It is also noted that the rate effect is critically different for the fracture samples of large grain size (marbles and granite) compared to smaller grain sizes (limestones). Variogram fractal dimension exhibits the strongest correlation with the maximum area covered by solvent, and display increasing trend at the moderate flow rates. Equations with variogram surface fractal dimension in combination with any other surface fractal parameter coupled with Peclet number can be used to predict maximum area covered by solvent in a single fracture, which in turn can be utilized to model oil recovery, waste disposal, and groundwater contamination processes in the presence of fractures.

Assessment of the Old Red Rock Indian Line Sycamore Tree, Lake Red Rock, Marion County, Iowa

DTIC Science & Technology

1992-01-01

miles, when reduced to a straight line , from the junction of the White Breast and Des Moines (Stiles 1911:4). George W. Harrison was instructed to...AD-A255 372 Assessment of the Old Red Rock Indian Line Sycamore Tree, Lake Red Rock, Marion County, Iowa DACW25-92-M-0414 by Leah D. Rogers Project...portion of tree 22 9. Map showing location of Red Rock line within treaty cession area of 23 1842 10. Portion of 1844 map showing incorrect placement of

Landscape, Mountain Worship and Astronomy in Socaire

NASA Astrophysics Data System (ADS)

Moyano, Ricardo

The spatiotemporal analysis of mountain worship in the indigenous community of Socaire, Atacama, northern Chile, relates to cultural, geographical, climatic, psychological, and astronomical information gathered from ethno archaeological studies. We identify a system of offerings to the mountains that incorporates concepts such as ceque (straight line), mayllku (mountain lord or ancestor), and pacha (space and time). Here, the mountains on the visible horizon (Tumisa, Lausa, Chiliques, Ipira, and Miñiques) feature as the fingers on the left hand (PAH Triad). This structure regulates annual activities and rituals and sets the basis for the Socaireños' worldview raised on a humanized landscape.

Photogrammetry of the solar aureole

NASA Technical Reports Server (NTRS)

Deepak, A.

1978-01-01

This paper presents a photogrammetric analysis of the solar aureole for the purpose of making photographic sky radiance measurements for determining aerosol physical characteristics. A photograph is essentially a projection of a 3-D object space onto a 2-D image space. Photogrammetry deals with relations that exist between the object and the image spaces. The main problem of photogrammetry is the reconstruction of configurations in the object space by means of the image space data. It is shown that the almucantar projects onto the photographic plane as a conic section and the sun vertical as a straight line.

Open-Cellular Co-Base and Ni-Base Superalloys Fabricated by Electron Beam Melting

PubMed Central

Murr, Lawrence; Li, Shujun; Tian, Yuxing; Amato, Krista; Martinez, Edwin; Medina, Frank

2011-01-01

Reticulated mesh samples of Co-29Cr-6Mo alloy and Ni-21Cr-9Mo-4Nb alloy (625) and stochastic foam samples of Co-29Cr-6Mo alloy fabricated by electron beam melting were characterized by optical metallography, and the dynamic stiffness (Young’s modulus) was measured by resonant frequency analysis. The relative stiffness (E/Es) versus relative density (ρ/ρs) plotted on a log-log basis resulted in a fitted straight line with a slope n ≅ 2, consistent with that for ideal open cellular materials. PMID:28879949

NJDOT Transportation Data User Survey

DOT National Transportation Integrated Search

2010-02-01

The New Jersey Straight Line Diagrams (SLD) is the main reference for the State's centerline roadway inventory. SLD was initially designed as a planning tool, but it has become a standard information platform for many other purposes within and outsid...

77 FR 64033 - Establishment of the Ancient Lakes of Columbia Valley Viticultural Area

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-18

...., Washington--Grant County, 1965; (10) Vantage, Washington, 1965, photorevised 1978; (11) Ginkgo, Washington...) Proceed west in a straight line along the section boundaries for approximately 7.9 miles, onto the Vantage...

26 CFR 1.167(e)-1 - Change in method.

Code of Federal Regulations, 2010 CFR

2010-04-01

... percent of the straight line rate, or any change in the interest factor used in connection with a compound interest or sinking fund method, will constitute a change in method of depreciation. Any request for a...

GPS/DR Error Estimation for Autonomous Vehicle Localization.

PubMed

Lee, Byung-Hyun; Song, Jong-Hwa; Im, Jun-Hyuck; Im, Sung-Hyuck; Heo, Moon-Beom; Jee, Gyu-In

2015-08-21

Autonomous vehicles require highly reliable navigation capabilities. For example, a lane-following method cannot be applied in an intersection without lanes, and since typical lane detection is performed using a straight-line model, errors can occur when the lateral distance is estimated in curved sections due to a model mismatch. Therefore, this paper proposes a localization method that uses GPS/DR error estimation based on a lane detection method with curved lane models, stop line detection, and curve matching in order to improve the performance during waypoint following procedures. The advantage of using the proposed method is that position information can be provided for autonomous driving through intersections, in sections with sharp curves, and in curved sections following a straight section. The proposed method was applied in autonomous vehicles at an experimental site to evaluate its performance, and the results indicate that the positioning achieved accuracy at the sub-meter level.

Mobile robot motion estimation using Hough transform

NASA Astrophysics Data System (ADS)

Aldoshkin, D. N.; Yamskikh, T. N.; Tsarev, R. Yu

2018-05-01

This paper proposes an algorithm for estimation of mobile robot motion. The geometry of surrounding space is described with range scans (samples of distance measurements) taken by the mobile robot’s range sensors. A similar sample of space geometry in any arbitrary preceding moment of time or the environment map can be used as a reference. The suggested algorithm is invariant to isotropic scaling of samples or map that allows using samples measured in different units and maps made at different scales. The algorithm is based on Hough transform: it maps from measurement space to a straight-line parameters space. In the straight-line parameters, space the problems of estimating rotation, scaling and translation are solved separately breaking down a problem of estimating mobile robot localization into three smaller independent problems. The specific feature of the algorithm presented is its robustness to noise and outliers inherited from Hough transform. The prototype of the system of mobile robot orientation is described.

GPS/DR Error Estimation for Autonomous Vehicle Localization

PubMed Central

Lee, Byung-Hyun; Song, Jong-Hwa; Im, Jun-Hyuck; Im, Sung-Hyuck; Heo, Moon-Beom; Jee, Gyu-In

2015-01-01

Autonomous vehicles require highly reliable navigation capabilities. For example, a lane-following method cannot be applied in an intersection without lanes, and since typical lane detection is performed using a straight-line model, errors can occur when the lateral distance is estimated in curved sections due to a model mismatch. Therefore, this paper proposes a localization method that uses GPS/DR error estimation based on a lane detection method with curved lane models, stop line detection, and curve matching in order to improve the performance during waypoint following procedures. The advantage of using the proposed method is that position information can be provided for autonomous driving through intersections, in sections with sharp curves, and in curved sections following a straight section. The proposed method was applied in autonomous vehicles at an experimental site to evaluate its performance, and the results indicate that the positioning achieved accuracy at the sub-meter level. PMID:26307997

Using Wannier functions to improve solid band gap predictions in density functional theory

DOE PAGES

Ma, Jie; Wang, Lin-Wang

2016-04-26

Enforcing a straight-line condition of the total energy upon removal/addition of fractional electrons on eigen states has been successfully applied to atoms and molecules for calculating ionization potentials and electron affinities, but fails for solids due to the extended nature of the eigen orbitals. Here we have extended the straight-line condition to the removal/addition of fractional electrons on Wannier functions constructed within the occupied/unoccupied subspaces. It removes the self-interaction energies of those Wannier functions, and yields accurate band gaps for solids compared to experiments. It does not have any adjustable parameters and the computational cost is at the DFT level.more » This method can also work for molecules, providing eigen energies in good agreement with experimental ionization potentials and electron affinities. Our approach can be viewed as an alternative approach of the standard LDA+U procedure.« less

Straight ahead running of a nonlinear car and driver model - new nonlinear behaviours highlighted

NASA Astrophysics Data System (ADS)

Della Rossa, Fabio; Mastinu, Giampiero

2018-05-01

The paper deals with the bifurcation analysis of a validated simple model describing a vehicle+driver running straight ahead. The mechanical model of the car has two degrees of freedom and the related equations of motion contain the nonlinear tyre characteristics. The driver is described by a very simple model. Bifurcation analysis is adopted for characterising straight ahead motion at different speeds for different drivers. A nonlinear sensitivity analysis is performed as a function of the driver's parameters and forward vehicle speed. A wealth of unreferenced bifurcations is discovered both for the understeering (UN) and for the oversteering (OV) vehicle. For the UN vehicle, a supercritical Hopf bifurcation may occur as the forward speed is increased. Also tangent (fold) bifurcations (saddle-node bifurcation of limit cycles) occur as the speed (or disturbance) is further increased. For the OV vehicle, a subcritical Hopf bifurcation occurs as the speed reaches a critical value. The preview distance (a driver's control parameter) plays a fundamental role in straight ahead driving. Either too short or too long preview distances are negative for straight ahead running.

Global solutions to the electrodynamic two-body problem on a straight line

NASA Astrophysics Data System (ADS)

Bauer, G.; Deckert, D.-A.; Dürr, D.; Hinrichs, G.

2017-06-01

The classical electrodynamic two-body problem has been a long standing open problem in mathematics. For motion constrained to the straight line, the interaction is similar to that of the two-body problem of classical gravitation. The additional complication is the presence of unbounded state-dependent delays in the Coulomb forces due to the finiteness of the speed of light. This circumstance renders the notion of local solutions meaningless, and therefore, straightforward ODE techniques cannot be applied. Here, we study the time-symmetric case, i.e., the Fokker-Schwarzschild-Tetrode (FST) equations, comprising both advanced and retarded delays. We extend the technique developed in Deckert and Hinrichs (J Differ Equ 260:6900-6929, 2016), where existence of FST solutions was proven on the half line, to ensure global existence—a result that had been obtained by Bauer (Ein Existenzsatz für die Wheeler-Feynman-Elektrodynamik, Herbert Utz Verlag, München, 1997). Due to the novel technique, the presented proof is shorter and more transparent but also relies on the idea to employ asymptotic data to characterize solutions.

Observation and parametrization of wave attenuation through the MIZ

NASA Astrophysics Data System (ADS)

Ardhuin, F.; Stopa, J.; Dumont, D.; Sévigny, C.; Collard, F.; Boutin, G.

2016-02-01

Swell evolution from the open ocean into sea ice is poorly understood, in particular the amplitude attenuation expected from scattering and dissipation. New synthetic aperture radar (SAR) data from Sentinel-1 wave mode reveal intriguing patterns of bright oscillating lines shaped like instant noodles. We investigate cases in which the oscillations are in the azimuth direction, around a straight line in the range direction. This observation is interpreted as the distortion by the SAR processing of crests from a first swell, due to the presence of a second swell. Since deviations from a straight line should be proportional to the orbital velocity towards the satellite, swell height can be estimated. The intensity of the backscatter modulation with a single swell can also be used to retrieve swell height as it is found that the constructive velocity bunching is very sensitive to wave height. Using a novel algorithm to invert the wave directional spectrum, we investigate several cases of attenuation in the Arctic and southern ocean. On this basis we have adjusted an empirical wave-ice dissipation source term in the WAVEWATCH III model.

Carbide Derived Carbon Super Capacitor Application

NASA Astrophysics Data System (ADS)

Appelgate, James; Bauer, Dave; Quirin, James; Lofland, S. E.; Hettinger, J. D.; Heon, M.; Gogotsi, Y.

2010-02-01

Supercapacitors can be applied into many different fields from nano-robots to high density energy storage. Growing TiC films from a know recipe and removing the transition metal element, Titanium, by chlorination leaves a carbon film that can then be applied as an electrode in a super capacitor. The problem is when the Titanium is removed from the film the stress induced by this process causes the films to fracture into isolated islands. The islands allow electrons to travel across them every easily, but there is no transfer of electrons from island to island. We present results of an investigation of a technique control the location of the fractures and use them to our benefit. Ideally, we want to create them to fracture in parallel lines. To force these fractures into straight lines we will purchase substrates with thermal SiO2 created on the surface of Si. Using an etching process we will removed a channel of SiO2 the same as the thickness of the TiC film we plan on growing. These channels will allow the fractures to form in a correlated way creating a straight line. )

Effects of the Use of Millimeter Waves on the Statistics of Writer-to-Reader Delays in Military Communications Systems,

DTIC Science & Technology

1980-12-01

distributions of Figs. 3 and 4 may be fitted quit, accurately by broken straight lines. If we had plotted the differential distributions directly...collection process. These fluctuations are smoothed by replacing the actual differential distribution by the derivative of the fitted broken-line lognormal...for each interval T. The constants in the distribution for each broken section of the lognormal approximations are found by fitting lines to the curve

Methods for trend analysis: Examples with problem/failure data

NASA Technical Reports Server (NTRS)

Church, Curtis K.

1989-01-01

Statistics are emphasized as an important role in quality control and reliability. Consequently, Trend Analysis Techniques recommended a variety of statistical methodologies that could be applied to time series data. The major goal of the working handbook, using data from the MSFC Problem Assessment System, is to illustrate some of the techniques in the NASA standard, some different techniques, and to notice patterns of data. Techniques for trend estimation used are: regression (exponential, power, reciprocal, straight line) and Kendall's rank correlation coefficient. The important details of a statistical strategy for estimating a trend component are covered in the examples. However, careful analysis and interpretation is necessary because of small samples and frequent zero problem reports in a given time period. Further investigations to deal with these issues are being conducted.

Macular Degeneration

MedlinePlus

... happens when the light-sensitive cells in the macula slowly break down. Your gradually lose your central vision. A common early symptom is that straight lines appear crooked. Regular comprehensive eye exams can detect macular degeneration before the disease causes vision loss. Treatment can ...

27 CFR 9.138 - Benmore Valley.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 1960, (photoinspected 1975); and (2) “Purdys Gardens, CA,” 7.5 Minute Series, edition of 1958.... 11 W., on the “Purdys Gardens, CA” U.S.G.S. map: (1) Then southwest in a straight line to the point...

27 CFR 9.138 - Benmore Valley.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 1960, (photoinspected 1975); and (2) “Purdys Gardens, CA,” 7.5 Minute Series, edition of 1958.... 11 W., on the “Purdys Gardens, CA” U.S.G.S. map: (1) Then southwest in a straight line to the point...

27 CFR 9.138 - Benmore Valley.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 1960, (photoinspected 1975); and (2) “Purdys Gardens, CA,” 7.5 Minute Series, edition of 1958.... 11 W., on the “Purdys Gardens, CA” U.S.G.S. map: (1) Then southwest in a straight line to the point...

Centripetal Force on an Overhead Projector.

ERIC Educational Resources Information Center

Rheam, Harry

1995-01-01

Describes two simple demonstrations of an object moving in a straight line tangent to the circle if centripetal force is removed. Demonstrations use a pie plate and petri dish with ball bearings to illustrate the phenomena on an overhead projector. (LZ)

Metabolic Power Requirement of Change of Direction Speed in Young Soccer Players: Not All Is What It Seems

PubMed Central

Mendez-Villanueva, Alberto; Palazzi, Dino; Ahmaidi, Saïd

2016-01-01

Purpose The aims of this study were to 1) compare the metabolic power demand of straight-line and change of direction (COD) sprints including 45° or 90°-turns, and 2) examine the relation between estimated metabolic demands and muscular activity throughout the 3 phases of COD-sprints. Methods Twelve highly-trained soccer players performed one 25-m and three 20-m sprints, either in straight-line or with one 45°- or 90°-COD. Sprints were monitored with 2 synchronized 100-Hz laser guns to assess players’ velocities before, during and after the COD. Acceleration and deceleration were derived from changes in speed over time. Metabolic power was estimated based on di Prampero’s approach (2005). Electromyography amplitude (RMS) of 2 lower limb muscles was measured. The expected energy expenditure during time-adjusted straight-line sprints (matching COD sprints time) was also calculated. Results Locomotor-dependant metabolic demand was largely lower with COD (90°, 142.1±13.5 J.kg-1) compared with time-adjusted (effect size, ES = -3.0; 193.2±18.6 J.kg-1) and non-adjusted straight-line sprints (ES = -1.7; 168.4±15.3 J.kg-1). Metabolic power requirement was angle-dependent, moderately lower for 90°-COD vs. 45°-COD sprint (ES = -1.0; 149.5±10.4 J.kg-1). Conversely, the RMS was slightly- (45°, ES = +0.5; +2.1%, 90% confidence limits (±3.6) for vastus lateralis muscle (VL)) to-largely (90°, ES = +1.6; +6.1 (3.3%) for VL) greater for COD-sprints. Metabolic power/RMS ratio was 2 to 4 times lower during deceleration than acceleration phases. Conclusion Present results show that COD-sprints are largely less metabolically demanding than linear sprints. This may be related to the very low metabolic demand associated with the deceleration phase during COD-sprints that may not be compensated by the increased requirement of the reacceleration phase. These results also highlight the dissociation between metabolic and muscle activity demands during COD-sprints, which questions the use of metabolic power as a single measure of running load in soccer. PMID:26930649

Map Projection Induced Variations in Locations of Polygon Geofence Edges

NASA Technical Reports Server (NTRS)

Neeley, Paula; Narkawicz, Anthony

2017-01-01

This Paper under-estimates answers to the following question under various constraints: If a geofencing algorithm uses a map projection to determine whether a position is inside/outside a polygon region, how far outside/inside the polygon can the point be and the algorithm determine that it is inside/outside (the opposite and therefore incorrect answer)? Geofencing systems for unmanned aircraft systems (UAS) often model stay-in and stay-out regions using 2D polygons with minimum and maximum altitudes. The vertices of the polygons are typically input as latitude-longitude pairs, and the edges as paths between adjacent vertices. There are numerous ways to generate these paths, resulting in numerous potential locations for the edges of stay-in and stay-out regions. These paths may be geodesics on a spherical model of the earth or geodesics on the WGS84 reference ellipsoid. In geofencing applications that use map projections, these paths are inverse images of straight lines in the projected plane. This projected plane may be a projection of a spherical earth model onto a tangent plane, called an orthographic projection. Alternatively, it may be a projection where the straight lines in the projected plane correspond to straight lines in the latitudelongitude coordinate system, also called a Plate Carr´ee projection. This paper estimates distances between different edge paths and an oracle path, which is a geodesic on either the spherical earth or the WGS84 ellipsoidal earth. This paper therefore estimates how far apart different edge paths can be rather than comparing their path lengths, which are not considered. Rather, the comparision is between the actual locations of the edges between vertices. For edges drawn using orthographic projections, this maximum distance increases as the distance from the polygon vertices to the projection point increases. For edges drawn using Plate Carr´ee projections, this maximum distance increases as the vertices become further from the equator. Distances between geodesics on a spherical earth and a WGS84 ellipsoidal earth are also analyzed, using the WGS84 ellipsoid as the oracle. Bounds on the 2D distance between a straight line and a great circle path, in an orthographically projected plane rather than on the surface of the earth, have been formally verified in the PVS theorem prover, meaning that they are mathematically correct in the absence of floating point errors.

Photovoltaic panel extraction from very high-resolution aerial imagery using region-line primitive association analysis and template matching

NASA Astrophysics Data System (ADS)

Wang, Min; Cui, Qi; Sun, Yujie; Wang, Qiao

2018-07-01

In object-based image analysis (OBIA), object classification performance is jointly determined by image segmentation, sample or rule setting, and classifiers. Typically, as a crucial step to obtain object primitives, image segmentation quality significantly influences subsequent feature extraction and analyses. By contrast, template matching extracts specific objects from images and prevents shape defects caused by image segmentation. However, creating or editing templates is tedious and sometimes results in incomplete or inaccurate templates. In this study, we combine OBIA and template matching techniques to address these problems and aim for accurate photovoltaic panel (PVP) extraction from very high-resolution (VHR) aerial imagery. The proposed method is based on the previously proposed region-line primitive association framework, in which complementary information between region (segment) and line (straight line) primitives is utilized to achieve a more powerful performance than routine OBIA. Several novel concepts, including the mutual fitting ratio and best-fitting template based on region-line primitive association analyses, are proposed. Automatic template generation and matching method for PVP extraction from VHR imagery are designed for concept and model validation. Results show that the proposed method can successfully extract PVPs without any user-specified matching template or training sample. High user independency and accuracy are the main characteristics of the proposed method in comparison with routine OBIA and template matching techniques.

14 CFR 417.215 - Straight-up time analysis.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 4 2014-01-01 2014-01-01 false Straight-up time analysis. 417.215 Section 417.215 Aeronautics and Space COMMERCIAL SPACE TRANSPORTATION, FEDERAL AVIATION ADMINISTRATION... vehicle's flight termination system or breakup of the launch vehicle would not cause hazardous debris or...

14 CFR 417.215 - Straight-up time analysis.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Straight-up time analysis. 417.215 Section 417.215 Aeronautics and Space COMMERCIAL SPACE TRANSPORTATION, FEDERAL AVIATION ADMINISTRATION... vehicle's flight termination system or breakup of the launch vehicle would not cause hazardous debris or...

14 CFR 417.215 - Straight-up time analysis.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 4 2011-01-01 2011-01-01 false Straight-up time analysis. 417.215 Section 417.215 Aeronautics and Space COMMERCIAL SPACE TRANSPORTATION, FEDERAL AVIATION ADMINISTRATION... vehicle's flight termination system or breakup of the launch vehicle would not cause hazardous debris or...

14 CFR 417.215 - Straight-up time analysis.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 4 2013-01-01 2013-01-01 false Straight-up time analysis. 417.215 Section 417.215 Aeronautics and Space COMMERCIAL SPACE TRANSPORTATION, FEDERAL AVIATION ADMINISTRATION... vehicle's flight termination system or breakup of the launch vehicle would not cause hazardous debris or...

14 CFR 417.215 - Straight-up time analysis.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 4 2012-01-01 2012-01-01 false Straight-up time analysis. 417.215 Section 417.215 Aeronautics and Space COMMERCIAL SPACE TRANSPORTATION, FEDERAL AVIATION ADMINISTRATION... vehicle's flight termination system or breakup of the launch vehicle would not cause hazardous debris or...

Stability analysis of flexible wind turbine blades using finite element method

NASA Technical Reports Server (NTRS)

Kamoulakos, A.

1982-01-01

Static vibration and flutter analysis of a straight elastic axis blade was performed based on a finite element method solution. The total potential energy functional was formulated according to linear beam theory. The inertia and aerodynamic loads were formulated according to the blade absolute acceleration and absolute velocity vectors. In vibration analysis, the direction of motion of the blade during the first out-of-lane and first in-plane modes was examined; numerical results involve NASA/DOE Mod-0, McCauley propeller, north wind turbine and flat plate behavior. In flutter analysis, comparison cases were examined involving several references. Vibration analysis of a nonstraight elastic axis blade based on a finite element method solution was performed in a similar manner with the straight elastic axis blade, since it was recognized that a curved blade can be approximated by an assembly of a sufficient number of straight blade elements at different inclinations with respect to common system of axes. Numerical results involve comparison between the behavior of a straight and a curved cantilever beam during the lowest two in-plane and out-of-plane modes.

Prism adaptation and neck muscle vibration in healthy individuals: are two methods better than one?

PubMed

Guinet, M; Michel, C

2013-12-19

Studies involving therapeutic combinations reveal an important benefit in the rehabilitation of neglect patients when compared to single therapies. In light of these observations our present work examines, in healthy individuals, sensorimotor and cognitive after-effects of prism adaptation and neck muscle vibration applied individually or simultaneously. We explored sensorimotor after-effects on visuo-manual open-loop pointing, visual and proprioceptive straight-ahead estimations. We assessed cognitive after-effects on the line bisection task. Fifty-four healthy participants were divided into six groups designated according to the exposure procedure used with each: 'Prism' (P) group; 'Vibration with a sensation of body rotation' (Vb) group; 'Vibration with a move illusion of the LED' (Vl) group; 'Association with a sensation of body rotation' (Ab) group; 'Association with a move illusion of the LED' (Al) group; and 'Control' (C) group. The main findings showed that prism adaptation applied alone or combined with vibration showed significant adaptation in visuo-manual open-loop pointing, visual straight-ahead and proprioceptive straight-ahead. Vibration alone produced significant after-effects on proprioceptive straight-ahead estimation in the Vl group. Furthermore all groups (except C group) showed a rightward neglect-like bias in line bisection following the training procedure. This is the first demonstration of cognitive after-effects following neck muscle vibration in healthy individuals. The simultaneous application of both methods did not produce significant greater after-effects than prism adaptation alone in both sensorimotor and cognitive tasks. These results are discussed in terms of transfer of sensorimotor plasticity to spatial cognition in healthy individuals. Copyright © 2013 IBRO. Published by Elsevier Ltd. All rights reserved.

Physics Notes.

ERIC Educational Resources Information Center

School Science Review, 1982

1982-01-01

Discusses dice model of exponential radionuclide decay; glancing and collinear perfectly elastic collisions; digital capacitance meter; use of top pan balance in physics; microcomputer calculation of gradient of straight line (includes complete Commodore PET computer program); Fresnel lenses; low-voltage radiant heater; Wheatssone's bridge used as…

Film-cooling effectiveness with developing coolant flow through straight and curved tubular passages

NASA Technical Reports Server (NTRS)

Papell, S. S.; Wang, C. R.; Graham, R. W.

1982-01-01

The data were obtained with an apparatus designed to determine the influence of tubular coolant passage curvature on film-cooling performance while simulating the developing flow entrance conditions more representative of cooled turbine blade. Data comparisons were made between straight and curved single tubular passages embedded in the wall and discharging at 30 deg angle in line with the tunnel flow. The results showed an influence of curvature on film-cooling effectiveness that was inversely proportional to the blowing rate. At the lowest blowing rate of 0.18, curvature increased the effectiveness of film cooling by 35 percent; but at a blowing rate of 0.76, the improvement was only 10 percent. In addition, the increase in film-cooling area coverage ranged from 100 percent down to 25 percent over the same blowing rates. A data trend reversal at a blowing rate of 1.5 showed the straight tubular passage's film-cooling effectiveness to be 20 percent greater than that of the curved passage with about 80 percent more area coverage. An analysis of turbulence intensity detain the mixing layer in terms of the position of the mixing interface relative to the wall supported the concept that passage curvature tends to reduce the diffusion of the coolant jet into the main stream at blowing rates below about. Explanations for the film-cooling performance of both test sections were made in terms differences in turbulences structure and in secondary flow patterns within the coolant jets as influenced by flow passage geometry.

Film-cooling effectiveness with developing coolant flow through straight and curved tubular passages

NASA Astrophysics Data System (ADS)

Papell, S. S.; Wang, C. R.; Graham, R. W.

1982-11-01

The data were obtained with an apparatus designed to determine the influence of tubular coolant passage curvature on film-cooling performance while simulating the developing flow entrance conditions more representative of cooled turbine blade. Data comparisons were made between straight and curved single tubular passages embedded in the wall and discharging at 30 deg angle in line with the tunnel flow. The results showed an influence of curvature on film-cooling effectiveness that was inversely proportional to the blowing rate. At the lowest blowing rate of 0.18, curvature increased the effectiveness of film cooling by 35 percent; but at a blowing rate of 0.76, the improvement was only 10 percent. In addition, the increase in film-cooling area coverage ranged from 100 percent down to 25 percent over the same blowing rates. A data trend reversal at a blowing rate of 1.5 showed the straight tubular passage's film-cooling effectiveness to be 20 percent greater than that of the curved passage with about 80 percent more area coverage. An analysis of turbulence intensity detain the mixing layer in terms of the position of the mixing interface relative to the wall supported the concept that passage curvature tends to reduce the diffusion of the coolant jet into the main stream at blowing rates below about. Explanations for the film-cooling performance of both test sections were made in terms differences in turbulences structure and in secondary flow patterns within the coolant jets as influenced by flow passage geometry.

Head and pelvic movement symmetry in horses during circular motion and in rising trot.

PubMed

Robartes, Helen; Fairhurst, Harriet; Pfau, Thilo

2013-12-01

Lameness examinations in horses often include lungeing and ridden exercise. To incorporate these exercises into the evidence-based decision making process aided by quantitative sensor based gait analysis, guideline values for movement asymmetry are needed. In this study, movement symmetry (MS) was quantified in horses during unridden and ridden trot on the straight and on the circle. Systematic changes in MS were expected as a result of the 'asymmetrical loading' caused by circular movement, the rising trot and the combination of the two. Out of 23 horses (age 4-20 years, height 13.3-17.2 hands), 13 presented within normal limits for head movement and 22 for pelvic movement. Inertial measurement units assessed MS of vertical head and sacral movement during trot in-hand, on the lunge and in rising trot (straight, left/right circle). Changes in MS between straight line trot and ridden exercise on the circle were more pronounced for the head than for the sacrum. The highest amount of asymmetry was observed during rising trot on the circle (symmetry index of the head: 1.23 for the left rein, 0.83 for the right rein; symmetry index of the sacrum 0.84 for the left rein, 1.15 for the right rein). Change in MS was significant between exercise conditions except for the difference between head displacement maxima. Horses had greatest asymmetry during rising trot on the circle, with MS values of comparable magnitude to mild lameness. Copyright © 2013 Elsevier Ltd. All rights reserved.

Senescent sperm performance in old male birds.

PubMed

Møller, A P; Mousseau, T A; Rudolfsen, G; Balbontín, J; Marzal, A; Hermosell, I; De Lope, F

2009-02-01

Senescence is the deterioration of the phenotype with age caused by negative effects of mutations acting late in life or the physiological deterioration of vital processes. Birds have traditionally been assumed to senescence slowly despite their high metabolic rates, high blood sugar levels and high body temperature. Here we investigate the patterns of age-related performance of sperm of a long distance migrant, the barn swallow Hirundo rustica, varying in age from 1 to 6 years, analysed by the computer-assisted sperm analysis equipment. Sperm showed deteriorating performance in terms of linear movement, track velocity, straight line velocity and reduced proportions of rapidly moving, progressive and motile sperm with age. In a second series of experiments, we assessed performance of sperm from the same males in neutral medium and in medium derived from the reproductive tract of females in an attempt to test if sperm of old males performed relatively better in female medium, as expected from extra-pair paternity being negatively related to male age, but not to female age. Older males showed consistently better performance in female medium than in neutral medium in terms of track velocity, straight line velocity and reduced proportions of rapidly moving, progressive and motile sperm, whereas young males showed better performance in neutral medium. These results provide evidence of declining sperm performance for important reproductive variables not only with age, but also with the sperm of old males performing differentially better in female medium than young males.

Straight-run vs. sex separate rearing for 2 broiler genetic lines Part 1: Live production parameters, carcass yield, and feeding behavior.

PubMed

Da Costa, M J; Zaragoza-Santacruz, S; Frost, T J; Halley, J; Pesti, G M

2017-08-01

The objective of this experiment was to evaluate the effects of raising broilers under sex separate and straight-run conditions for 2 broiler strains. Day-old Ross 308 and Ross 708 chicks (n = 1,344) were separated by sex and placed in 48 pens according to the rearing type: sex separate (28 males or 28 females) or straight-run (14 males + 14 females). There were 3 dietary phases: starter (zero to 17 d), grower (17 to 32 d), and finisher (32 to 48 d). Birds' individual BW and feed intakes were measured at 12, 17, 25, 32, 42, and 48 d to evaluate performance. At 33, 43, and 49 d, 4 birds per pen were sampled for carcass yield evaluation. Additionally, from 06:00 to 06:30, 13:00 to 13:30, and 22:00 to 22:30, video records were taken to assess behavior at 45 days. Data were analyzed as CRD with a 2 × 3 factorial arrangement of treatments over time. Throughout the experiment Ross 308 were heavier than the 708, and after 17 d, male pens had the heavier birds, followed by straight-run and then females. Straight-run pens had higher BW CV in comparison with sex separate pens. Sex separate male BW was negatively impacted from 17 to 32 days. On the other hand, females raised sex separate were heavier than females raised straight-run with lower CV from 25 to 41 days. Post 25 d, FCR was the lowest in male pens whereas feed intake was the highest for these pens after 17 days. Overall, males had total carcass cut-up weights higher than straight-run and females at the 3 processing times. The Ross 708 had higher white meat yields, whereas 308 had higher yields for dark meat. Feeding behavior results were not consistent over time. However, from 13:00 to 13:30, birds in female pens spent more time eating, followed by straight-run and then males. In conclusion, raising females in a straight-run system negatively impacted performance and CV, whereas males benefited from straight-run rearing, with the differences being possibly related to feeder space competition. © 2017 Poultry Science Association Inc.

Force Tests of the Boeing XB-47 Full-Scale Empennage in the Ames 40- by 80-Foot Wind Tunnel

NASA Technical Reports Server (NTRS)

Hunton, Lynn W.

1947-01-01

A wind-tunnel investigation of the Boeing XB-47 full-scale empennage was conducted to provide, prior to flight tests, data required on the effectiveness of the elevator and rudder. The XB-47 airplane is a jet-propelled medium bomber having wing and tail surfaces swept back 35 degrees. The investigation included tests of the effectiveness of the elevator with normal straight sides, with a buldged trailing edge, and with a modified hinge-line gap and tests of the effectiveness of the rudder with a normal straight-sided tab and with a bulged tab.

Related Rates and the Speed of Light.

ERIC Educational Resources Information Center

Althoen, S. C.; Weidner, J. F.

1985-01-01

Standard calculus textbooks often include a related rates problem involving light cast onto a straight line by a revolving light source. Mathematical aspects to these problems (both in the solution and in the method by which that solution is obtained) are examined. (JN)

DISTANT GOAL ORIENTATION IN BIRDS.

DTIC Science & Technology

homing to a Bowling Green , Ohio loft. Pigeons with one eye surgically removed were able to home. Helicopter tracking is suitable and efficient for...the observation of pigeon navigation behavior. The homeward path varies considerably from the straight line path, sudden attitude changes occur, very

Line drawing extraction from gray level images by feature integration

NASA Astrophysics Data System (ADS)

Yoo, Hoi J.; Crevier, Daniel; Lepage, Richard; Myler, Harley R.

1994-10-01

We describe procedures that extract line drawings from digitized gray level images, without use of domain knowledge, by modeling preattentive and perceptual organization functions of the human visual system. First, edge points are identified by standard low-level processing, based on the Canny edge operator. Edge points are then linked into single-pixel thick straight- line segments and circular arcs: this operation serves to both filter out isolated and highly irregular segments, and to lump the remaining points into a smaller number of structures for manipulation by later stages of processing. The next stages consist in linking the segments into a set of closed boundaries, which is the system's definition of a line drawing. According to the principles of Gestalt psychology, closure allows us to organize the world by filling in the gaps in a visual stimulation so as to perceive whole objects instead of disjoint parts. To achieve such closure, the system selects particular features or combinations of features by methods akin to those of preattentive processing in humans: features include gaps, pairs of straight or curved parallel lines, L- and T-junctions, pairs of symmetrical lines, and the orientation and length of single lines. These preattentive features are grouped into higher-level structures according to the principles of proximity, similarity, closure, symmetry, and feature conjunction. Achieving closure may require supplying missing segments linking contour concavities. Choices are made between competing structures on the basis of their overall compliance with the principles of closure and symmetry. Results include clean line drawings of curvilinear manufactured objects. The procedures described are part of a system called VITREO (viewpoint-independent 3-D recognition and extraction of objects).

Comparative proteome analysis of cryopreserved flagella and head plasma membrane proteins from sea bream spermatozoa: effect of antifreeze proteins.

PubMed

Zilli, Loredana; Beirão, José; Schiavone, Roberta; Herraez, Maria Paz; Gnoni, Antonio; Vilella, Sebastiano

2014-01-01

Cryopreservation induces injuries to fish spermatozoa that in turn affect sperm quality in terms of fertilization ability, motility, DNA and protein integrity and larval survival. To reduce the loss of sperm quality due to freezing-thawing, it is necessary to improve these procedures. In the present study we investigated the ability of two antifreeze proteins (AFPI and AFPIII) to reduce the loss of quality of sea bream spermatozoa due to cryopreservation. To do so, we compared viability, motility, straight-line velocity and curvilinear velocity of fresh and (AFPs)-cryopreserved spermatozoa. AFPIII addition to cryopreservation medium improved viability, motility and straight-line velocity with respect to DMSO or DMSO plus AFPI. To clarify the molecular mechanism(s) underlying these findings, the protein profile of two different cryopreserved sperm domains, flagella and head plasma membranes, was analysed. The protein profiles differed between fresh and frozen-thawed semen and results of the image analysis demonstrated that, after cryopreservation, out of 270 proteins 12 were decreased and 7 were increased in isolated flagella, and out of 150 proteins 6 showed a significant decrease and 4 showed a significant increase in head membranes. Mass spectrometry analysis identified 6 proteins (4 from isolated flagella and 2 present both in flagella and head plasma membranes) within the protein spots affected by the freezing-thawing procedure. 3 out of 4 proteins from isolated flagella were involved in the sperm bioenergetic system. Our results indicate that the ability of AFPIII to protect sea bream sperm quality can be, at least in part, ascribed to reducing changes in the sperm protein profile occurring during the freezing-thawing procedure. Our results clearly demonstrated that AFPIII addition to cryopreservation medium improved the protection against freezing respect to DMSO or DMSO plus AFPI. In addition we propose specific proteins of spermatozoa as markers related to the procedures of fish sperm cryopreservation.

Use of a Multiwavelength Pyrometer in Several Elevated Temperature Aerospace Applications

NASA Technical Reports Server (NTRS)

Ng, Daniel; Fralick, Gustave

2001-01-01

A multiwavelength pyrometer was developed for applications unique to aerospace environments. It was shown to be a useful and versatile technique for measuring temperature, even when the emissivity is unknown. It has also been used to measure the surface temperatures of ceramic zircomia thermal barrier coatings and alumina. The close agreement between pyrometer and thin film thermocouple temperatures provided an independent check. Other applications of the multiwavelength pyrometer are simultaneous surface and bulk temperature measurements of a transparent material, and combustion gas temperature measurement using a special probe interfaced to the multiwavelength pyrometer via an optical fiber. The multiwavelength pyrometer determined temperature by transforming the radiation spectrum in a broad wavelength region to produce a straight line (in a certain spectral region), whose intercept in the vertical axis gives the temperature. Implicit in a two-color pyrometer is the assumption of wavelength independent emissivity. Though the two data points of a two-color pyrometer similarly processed would result immediately in a similar straight line to give the unknown temperature, the two-color pyrometer lacks the greater data redundancy of the multiwavelength pyrometer, which enables it to do so with improved accuracy. It also confirms that emissivity is indeed wavelength independent, as evidenced by a multitude of the data lying on a simple straight line. The multiwavelength pyrometer was also used to study the optical transmission properties of a nanostructured material from which a quadratic exponential functional frequency dependence of its spectral transmission was determined. Finally, by operating the multiwavelength pyrometer in a very wide field of view mode, the surface temperature distribution of a large hot surface was obtained through measurement of just a single radiation spectrum.

Validation of travel times to hospital estimated by GIS.

PubMed

Haynes, Robin; Jones, Andrew P; Sauerzapf, Violet; Zhao, Hongxin

2006-09-19

An increasing number of studies use GIS estimates of car travel times to health services, without presenting any evidence that the estimates are representative of real travel times. This investigation compared GIS estimates of travel times with the actual times reported by a sample of 475 cancer patients who had travelled by car to attend clinics at eight hospitals in the North of England. Car travel times were estimated by GIS using the shortest road route between home address and hospital and average speed assumptions. These estimates were compared with reported journey times and straight line distances using graphical, correlation and regression techniques. There was a moderately strong association between reported times and estimated travel times (r = 0.856). Reported travel times were similarly related to straight line distances. Altogether, 50% of travel time estimates were within five minutes of the time reported by respondents, 77% were within ten minutes and 90% were within fifteen minutes. The distribution of over- and under-estimates was symmetrical, but estimated times tended to be longer than reported times with increasing distance from hospital. Almost all respondents rounded their travel time to the nearest five or ten minutes. The reason for many cases of reported journey times exceeding the estimated times was confirmed by respondents' comments as traffic congestion. GIS estimates of car travel times were moderately close approximations to reported times. GIS travel time estimates may be superior to reported travel times for modelling purposes because reported times contain errors and can reflect unusual circumstances. Comparison with reported times did not suggest that estimated times were a more sensitive measure than straight line distance.

Activity Profiles and Physiological Responses of Representative Tag Football Players in Relation to Playing Position and Physical Fitness

PubMed Central

2015-01-01

This study determined the physical fitness, match-activity profiles and physiological responses of representative tag football players and examined the relationship between physical fitness and the match-activity profile. Microtechnology devices and heart rate (HR) chest straps were used to determine the match-activity profiles of sixteen tag football players for five matches during the 2014 Australian National Championships. The relationships between lower body muscular power, straight line running speed and Yo-Yo intermittent recovery test level 2 (Yo-Yo IR2) and the match-activity profile were examined using Pearson’s correlation coefficients. Outside players had greater lower body muscular power (ES = 0.98) and straight line running speed (ES = 1.03–1.18) than inside players, and also covered greater very high-speed running (VHSR) distance/min (ES = 0.67) and reached higher peak running speeds (ES = 0.95) during matches. Inside and outside players performed a similar number of repeated high-intensity effort (RHIE) bouts and reported similar mean and maximum efforts per RHIE bout. However, there were differences between playing positions for mean and maximal RHIE effort durations (ES = 0.69–1.15) and mean RHIE bout recovery (ES = 0.56). Inside and outside players also reported small to moderate differences (ES = 0.43–0.80) for times spent in each HR zone. There were a number of moderate to very large correlations between physical fitness measures and match-activity profile variables. This study found lower body muscular power, straight line running speed and Yo-Yo IR2 to be related to the match-activities of representative tag football players, although differences between inside and outside players suggest that athlete testing and training practices should be modified for different playing positions. PMID:26642320

The effects of prosthetic foot stiffness on transtibial amputee walking mechanics and balance control during turning.

PubMed

Shell, Courtney E; Segal, Ava D; Klute, Glenn K; Neptune, Richard R

2017-11-01

Little evidence exists regarding how prosthesis design characteristics affect performance in tasks that challenge mediolateral balance such as turning. This study assesses the influence of prosthetic foot stiffness on amputee walking mechanics and balance control during a continuous turning task. Three-dimensional kinematic and kinetic data were collected from eight unilateral transtibial amputees as they walked overground at self-selected speed clockwise and counterclockwise around a 1-meter circle and along a straight line. Subjects performed the walking tasks wearing three different ankle-foot prostheses that spanned a range of sagittal- and coronal-plane stiffness levels. A decrease in stiffness increased residual ankle dorsiflexion (10-13°), caused smaller adaptations (<5°) in proximal joint angles, decreased residual and increased intact limb body support, increased residual limb propulsion and increased intact limb braking for all tasks. While changes in sagittal-plane joint work due to decreased stiffness were generally consistent across tasks, effects on coronal-plane hip work were task-dependent. When the residual limb was on the inside of the turn and during straight-line walking, coronal-plane hip work increased and coronal-plane peak-to-peak range of whole-body angular momentum decreased with decreased stiffness. Changes in sagittal-plane kinematics and kinetics were similar to those previously observed in straight-line walking. Mediolateral balance improved with decreased stiffness, but adaptations in coronal-plane angles, work and ground reaction force impulses were less systematic than those in sagittal-plane measures. Effects of stiffness varied with the residual limb inside versus outside the turn, which suggests that actively adjusting stiffness to turn direction may be beneficial. Copyright © 2017 Elsevier Ltd. All rights reserved.

THz and sub-THz (MMW)-over-Fiber Data Links and Radar Technology

DTIC Science & Technology

2016-12-05

propagation loss in free-space or transmission line, and their inherent straight-line path of propagation affects connections and synchronization between the...effort is to realize photonic-network compatible wireless data link at data rate up to 100 Gbit/s, and to explore a real-time MMW radar imaging system...global village at terabit rate, hopefully wirelessly. Unfortunately, such high-volume data transmission over air consumes radio bandwidth—lots of it

THz and sub THz (MMW)-over-Fiber Data Links and Radar Technology

DTIC Science & Technology

2016-11-30

propagation loss in free-space or transmission line, and their inherent straight-line path of propagation affects connections and synchronization between the...effort is to realize photonic-network compatible wireless data link at data rate up to 100 Gbit/s, and to explore a real-time MMW radar imaging system...global village at terabit rate, hopefully wirelessly. Unfortunately, such high-volume data transmission over air consumes radio bandwidth—lots of it

Custom-Made Pyramids.

DTIC Science & Technology

1986-11-01

V2 + V 2 2 We can formulate the general weighted resampling formulas by giving an inter - polation formula and a sampling formula. Specifically...tessellation grids. 4.1. One-dimensional Adaptive Pyramid We suggest an interest operator based on the local " busyness " of the data. It has been observed...that in human perception a line with higher " busyness " seems longer than a straight line segment [6], as in Figure 7. Here, we will use a smoothed

A real-time visual inspection method of fastening bolts in freight car operation

NASA Astrophysics Data System (ADS)

Nan, Guo; Yao, JunEn

2015-10-01

A real-time inspection of the key components is necessary for ensuring safe operation of freight car. While traditional inspection depends on the trained human inspectors, which is time-consuming and lower efficient. With the development of machine vision, vision-based inspection methods get more railway on-spot applications. The cross rod end fastening bolts are important components on both sides of the train body that fixing locking plates together with the freight car main structure. In our experiment, we get the images containing fastening bolt components, and accurately locate the locking plate position using a linear Support Vector Machine (SVM) locating model trained with Histograms of Oriented Gradients (HOG) features. Then we extract the straight line segment using the Line Segment Detector (LSD) and encoding them in a range, which constitute a straight line segment dataset. Lastly we determine the locking plate's working state by the linear pattern. The experiment result shows that the localization accurate rate is over 99%, the fault detection rate is over 95%, and the module implementation time is 2f/s. The overall performance can completely meet the practical railway safety assurance application.

47 CFR 15.31 - Measurement standards.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., such as perimeter protection systems, carrier current systems, and systems employing a “leaky” coaxial cable as an antenna, measurements for verification or for obtaining a grant of equipment authorization... interconnecting cables as determined by the boundary defined by an imaginary straight line periphery describing a...

Adjustable knife cuts honeycomb material to specified depth

NASA Technical Reports Server (NTRS)

Rauschl, J. A.

1966-01-01

Calibrated, adjustable knife cuts aluminum honeycomb or other soft materials to a desired depth. The frame of the device accommodates standard commercial blades. Since the blade is always visible to the operator, the device can be used on any straight or irregular layout line.

Three Perspectives on Teaching Least Squares

ERIC Educational Resources Information Center

Scariano, Stephen M.; Calzada, Maria

2004-01-01

The method of Least Squares is the most widely used technique for fitting a straight line to data, and it is typically discussed in several undergraduate courses. This article focuses on three developmentally different approaches for solving the Least Squares problem that are suitable for classroom exposition.

78 FR 45283 - Missouri Disaster #MO-00066

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-26

... 07/18/2013. Incident: Severe Storms, Straight-line Winds, Tornadoes, and Flooding. Incident Period: 05/29/2013 through 06/10/2013. Effective Date: 07/18/2013. Physical Loan Application Deadline Date: 09/16/2013. Economic Injury (EIDL) Loan Application Deadline Date: 04/18/2014. ADDRESSES: Submit...

Theoretical limit of spatial resolution in diffuse optical tomography using a perturbation model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Konovalov, A B; Vlasov, V V

2014-03-28

We have assessed the limit of spatial resolution of timedomain diffuse optical tomography (DOT) based on a perturbation reconstruction model. From the viewpoint of the structure reconstruction accuracy, three different approaches to solving the inverse DOT problem are compared. The first approach involves reconstruction of diffuse tomograms from straight lines, the second – from average curvilinear trajectories of photons and the third – from total banana-shaped distributions of photon trajectories. In order to obtain estimates of resolution, we have derived analytical expressions for the point spread function and modulation transfer function, as well as have performed a numerical experiment onmore » reconstruction of rectangular scattering objects with circular absorbing inhomogeneities. It is shown that in passing from reconstruction from straight lines to reconstruction using distributions of photon trajectories we can improve resolution by almost an order of magnitude and exceed the accuracy of reconstruction of multi-step algorithms used in DOT. (optical tomography)« less

14 CFR 417.207 - Trajectory analysis.

Code of Federal Regulations, 2011 CFR

2011-01-01

... after lift-off, the limits of a launch vehicle's normal flight, as defined by the nominal trajectory and... straight-up trajectory for any time after lift-off until the straight-up time that would result if the...

14 CFR 417.207 - Trajectory analysis.

Code of Federal Regulations, 2010 CFR

2010-01-01

... after lift-off, the limits of a launch vehicle's normal flight, as defined by the nominal trajectory and... straight-up trajectory for any time after lift-off until the straight-up time that would result if the...

Timing of Tympanostomy Tube Placement and Efficacy of Palatoplasty Technique on the Resolution of Chronic Otitis Media: A Cross-sectional Analysis

PubMed Central

Brgoch, M. S.; Dodson, K. M.; Kim, T. C.; Kim, D. M.; Rhodes, J. L.

2015-01-01

Background: Chronic otitis media with effusion is a persistent complication essentially universal in children with cleft palate. The prevalence of chronic otitis media with effusion is hypothesized to be a result of Eustachian tube dysfunction secondary to the anomalous insertion of the palatal musculature. This study was designed to evaluate the timing of tympanostomy tube placement and the effect of primary palatoplasty technique on the recovery of Eustachian tube function and resolution of chronic otitis media with effusion. Methods: We performed a retrospective, cross-sectional analysis of the previous 99 consecutive patients who underwent a palatoplasty at our institution. Variables included timing of initial tympanostomy tube placement, palatoplasty technique, cleft type, and gender. These were then evaluated to assess their impact on the resolution of chronic otitis media with effusion. Resolution was established as an inverse function of the number of tympanostomy tubes placed in correlation with available audiometric/tympanographic data. For all models, a generalized linear mixed model was applied using a Poisson distribution and a log-link function where the outcome variable was the total number of tympanostomy tubes. For all tests, a P = .05 level of significance was used. Results: Of 99 palatoplasties performed, 94 patients were included in the study. Ninety-one percent of patients had documented chronic otitis media with effusion at the time of palatoplasty. Forty-four percent underwent straight-line repair with aggressive intravelar veloplasty, 36% had Furlow double z-plasty, 20% had straight-line repair without intravelar veloplasty. There was a statistically significant difference (F2,83 = 5.36, P = .0065) between the 3 types of repair. The mean number of tubes placed was 0.6000 ± 0.1225, 0.8519 ± 0.1776, and 1.4737 ± 0.2785 for intravelar veloplasty, Furlow double z-plasty, and straight line without intravelar veloplasty, respectively . With regard to the timing of tympanostomy tube placement, there was a trend toward statistical significant (F2,83 = 3.02, P = .0540) in the mean number of tube insertions was 1.4286 ± 0.4518, 0.6964 ± 0.1115, and 1.1304 ± 0.2217 when the initial set was placed before palatoplasty, at the time of palatoplasty, and after palatoplasty, respectively. Conclusions: Despite its inherent limitations, this study suggests that palatal musculature reconstruction via intravelar veloplasty or reorientation via Furlow double z-plasty may improve Eustachian tube function and lower the need for tympanostomy tubes in this population. In comparison with other time points, patients who underwent initial tympanostomy tube placement at the time of palatoplasty trended toward improved chronic otitis media with effusion. PMID:26240670

Analysis and experimental studies of the control of hang gliders

NASA Technical Reports Server (NTRS)

Phillips, W. H.

1974-01-01

A theoretical analysis of the longitudinal and lateral characteristics of hang gliders in straight flight, pullups, and turns is presented. Some examples of the characteristics of a straight-wing configuration and a Rogallo-wing configuration are given. A means for improving the control of hang gliders while retaining the same basic control feel is proposed.

Time-varying impedance of the human ankle in the sagittal and frontal planes during straight walk and turning steps.

PubMed

Ficanha, Evandro M; Ribeiro, Guilherme A; Knop, Lauren; Rastgaar, Mo

2017-07-01

This paper describes the methods and experiment protocols for estimation of the human ankle impedance during turning and straight line walking. The ankle impedance of two human subjects during the stance phase of walking in both dorsiflexion plantarflexion (DP) and inversion eversion (IE) were estimated. The impedance was estimated about 8 axes of rotations of the human ankle combining different amounts of DP and IE rotations, and differentiating among positive and negative rotations at 5 instants of the stance length (SL). Specifically, the impedance was estimated at 10%, 30%, 50%, 70% and 90% of the SL. The ankle impedance showed great variability across time, and across the axes of rotation, with consistent larger stiffness and damping in DP than IE. When comparing straight walking and turning, the main differences were in damping at 50%, 70%, and 90% of the SL with an increase in damping at all axes of rotation during turning.

Aerodynamic analysis of the Darrieus rotor including secondary effects

NASA Astrophysics Data System (ADS)

Paraschivoiu, I.; Delclaux, F.; Fraunie, P.; Beguier, C.

1983-10-01

An aerodynamic analysis is made of two variants of the two-actuator-disk theory for modeling the Darrieus wind turbine. The double-multiple-streamtube model with constant and variable interference factors, including secondary effects, is examined for a Darrieus rotor. The influence of the secondary effects, namely, the blade geometry and profile type, the rotating tower, and the presence of struts and aerodynamic spoilers, is relatively significant, especially at high tip-speed ratios. Variation of the induced velocity as a function of the azimuthal angle allows a more accurate calculation of the aerodynamic loads on the downwind zone of the rotor with respect to the assumed constant interference factors. The theoretical results were compared with available experimental data for the Magdalen Islands wind turbine and Sandia-type machines (straight-line/circular-arc shape).

Analysis of Different Blade Architectures on small VAWT Performance

NASA Astrophysics Data System (ADS)

Battisti, L.; Brighenti, A.; Benini, E.; Raciti Castelli, M.

2016-09-01

The present paper aims at describing and comparing different small Vertical Axis Wind Turbine (VAWT) architectures, in terms of performance and loads. These characteristics can be highlighted by resorting to the Blade Element-Momentum (BE-M) model, commonly adopted for rotor pre-design and controller assessment. After validating the model with experimental data, the paper focuses on the analysis of VAWT loads depending on some relevant rotor features: blade number (2 and 3), airfoil camber line (comparing symmetrical and asymmetrical profiles) and blade inclination (straight versus helical blade). The effect of such characteristics on both power and thrusts (in the streamwise direction and in the crosswise one) as a function of both the blades azimuthal position and their Tip Speed Ratio (TSR) are presented and widely discussed.

Using Time-Series Regression to Predict Academic Library Circulations.

ERIC Educational Resources Information Center

Brooks, Terrence A.

1984-01-01

Four methods were used to forecast monthly circulation totals in 15 midwestern academic libraries: dummy time-series regression, lagged time-series regression, simple average (straight-line forecasting), monthly average (naive forecasting). In tests of forecasting accuracy, dummy regression method and monthly mean method exhibited smallest average…

Naive vs. Sophisticated Methods of Forecasting Public Library Circulations.

ERIC Educational Resources Information Center

Brooks, Terrence A.

1984-01-01

Two sophisticated--autoregressive integrated moving average (ARIMA), straight-line regression--and two naive--simple average, monthly average--forecasting techniques were used to forecast monthly circulation totals of 34 public libraries. Comparisons of forecasts and actual totals revealed that ARIMA and monthly average methods had smallest mean…

Calibrating Reach Distance to Visual Targets

ERIC Educational Resources Information Center

Mon-Williams, Mark; Bingham, Geoffrey P.

2007-01-01

The authors investigated the calibration of reach distance by gradually distorting the haptic feedback obtained when participants grasped visible target objects. The authors found that the modified relationship between visually specified distance and reach distance could be captured by a straight-line mapping function. Thus, the relation could be…

EXAMINATION - ASTRONAUT CARPENTER - SCHOOL OF AVIATION MEDICINE - PENSACOLA, FL

NASA Image and Video Library

1961-12-07

S61-04571 (1961) --- Astronaut M. Scott Carpenter's balance mechanism performance is tested as he walks a straight line by putting one foot directly in front of the other. He is performing this test at the School of Aviation Medicine, Pensicola, Florida. Photo credit: NASA

40 CFR 89.320 - Carbon monoxide analyzer calibration.

Code of Federal Regulations, 2010 CFR

2010-07-01

... introduction into service and annually thereafter, the NDIR carbon monoxide analyzer shall be checked for... to its introduction into service, after any maintenance which could alter calibration, and every two... engineering practice. For each range calibrated, if the deviation from a least-squares best-fit straight line...

Explorations in Statistics: Correlation

ERIC Educational Resources Information Center

Curran-Everett, Douglas

2010-01-01

Learning about statistics is a lot like learning about science: the learning is more meaningful if you can actively explore. This sixth installment of "Explorations in Statistics" explores correlation, a familiar technique that estimates the magnitude of a straight-line relationship between two variables. Correlation is meaningful only when the…

Do residents’ perceptions of being well-placed and objective presence of local amenities match? A case study in West Central Scotland, UK

PubMed Central

2013-01-01

Background Recently there has been growing interest in how neighbourhood features, such as the provision of local facilities and amenities, influence residents’ health and well-being. Prior research has measured amenity provision through subjective measures (surveying residents’ perceptions) or objective (GIS mapping of distance) methods. The latter may provide a more accurate measure of physical access, but residents may not use local amenities if they do not perceive them as ‘local’. We believe both subjective and objective measures should be explored, and use West Central Scotland data to investigate correspondence between residents’ subjective assessments of how well-placed they are for everyday amenities (food stores, primary and secondary schools, libraries, pharmacies, public recreation), and objective GIS-modelled measures, and examine correspondence by various sub-groups. Methods ArcMap was used to map the postal locations of ‘Transport, Health and Well-being 2010 Study’ respondents (n = 1760), and the six amenities, and the presence/absence of each of them within various straight-line and network buffers around respondents’ homes was recorded. SPSS was used to investigate whether objective presence of an amenity within a specified buffer was perceived by a respondent as being well-placed for that amenity. Kappa statistics were used to test agreement between measures for all respondents, and by sex, age, social class, area deprivation, car ownership, dog ownership, walking in the local area, and years lived in current home. Results In general, there was poor agreement (Kappa <0.20) between perceptions of being well-placed for each facility and objective presence, within 800 m and 1000 m straight-line and network buffers, with the exception of pharmacies (at 1000 m straight-line) (Kappa: 0.21). Results varied between respondent sub-groups, with some showing better agreement than others. Amongst sub-groups, at 800 m straight-line buffers, the highest correspondence between subjective and objective measures was for pharmacies and primary schools, and at 1000 m, for pharmacies, primary schools and libraries. For road network buffers under 1000 m, agreement was generally poor. Conclusion Respondents did not necessarily regard themselves as well-placed for specific amenities when these amenities were present within specified boundaries around their homes, with some exceptions; the picture is not clear-cut with varying findings between different amenities, buffers, and sub-groups. PMID:23651734

A multi-directional and multi-scale roughness filter to detect lineament segments on digital elevation models - analyzing spatial objects in R

NASA Astrophysics Data System (ADS)

Baumann, Sebastian; Robl, Jörg; Wendt, Lorenz; Willingshofer, Ernst; Hilberg, Sylke

2016-04-01

Automated lineament analysis on remotely sensed data requires two general process steps: The identification of neighboring pixels showing high contrast and the conversion of these domains into lines. The target output is the lineaments' position, extent and orientation. We developed a lineament extraction tool programmed in R using digital elevation models as input data to generate morphological lineaments defined as follows: A morphological lineament represents a zone of high relief roughness, whose length significantly exceeds the width. As relief roughness any deviation from a flat plane, defined by a roughness threshold, is considered. In our novel approach a multi-directional and multi-scale roughness filter uses moving windows of different neighborhood sizes to identify threshold limited rough domains on digital elevation models. Surface roughness is calculated as the vertical elevation difference between the center cell and the different orientated straight lines connecting two edge cells of a neighborhood, divided by the horizontal distance of the edge cells. Thus multiple roughness values depending on the neighborhood sizes and orientations of the edge connecting lines are generated for each cell and their maximum and minimum values are extracted. Thereby negative signs of the roughness parameter represent concave relief structures as valleys, positive signs convex relief structures as ridges. A threshold defines domains of high relief roughness. These domains are thinned to a representative point pattern by a 3x3 neighborhood filter, highlighting maximum and minimum roughness peaks, and representing the center points of lineament segments. The orientation and extent of the lineament segments are calculated within the roughness domains, generating a straight line segment in the direction of least roughness differences. We tested our algorithm on digital elevation models of multiple sources and scales and compared the results visually with shaded relief map of these digital elevation models. The lineament segments trace the relief structure to a great extent and the calculated roughness parameter represents the physical geometry of the digital elevation model. Modifying the threshold for the surface roughness value highlights different distinct relief structures. Also the neighborhood size at which lineament segments are detected correspond with the width of the surface structure and may be a useful additional parameter for further analysis. The discrimination of concave and convex relief structures perfectly matches with valleys and ridges of the surface.

Off-shell amplitudes as boundary integrals of analytically continued Wilson line slope

NASA Astrophysics Data System (ADS)

Kotko, P.; Serino, M.; Stasto, A. M.

2016-08-01

One of the methods to calculate tree-level multi-gluon scattering amplitudes is to use the Berends-Giele recursion relation involving off-shell currents or off-shell amplitudes, if working in the light cone gauge. As shown in recent works using the light-front perturbation theory, solutions to these recursions naturally collapse into gauge invariant and gauge-dependent components, at least for some helicity configurations. In this work, we show that such structure is helicity independent and emerges from analytic properties of matrix elements of Wilson line operators, where the slope of the straight gauge path is shifted in a certain complex direction. This is similar to the procedure leading to the Britto-Cachazo-Feng-Witten (BCFW) recursion, however we apply a complex shift to the Wilson line slope instead of the external momenta. While in the original BCFW procedure the boundary integrals over the complex shift vanish for certain deformations, here they are non-zero and are equal to the off-shell amplitudes. The main result can thus be summarized as follows: we derive a decomposition of a helicity-fixed off-shell current into gauge invariant component given by a matrix element of a straight Wilson line plus a reminder given by a sum of products of gauge invariant and gauge dependent quantities. We give several examples realizing this relation, including the five-point next-to-MHV helicity configuration.

METAL SPRAYER FOR USE IN VACUUM OR INERT ATMOSPHERE

DOEpatents

Monroe, R.E.

1958-10-14

A metal sprayer is described for use in a vacuum or inert atmosphere with a straight line wire feed and variable electrode contact angle. This apparatus comprises two wires which are fed through straight tubes of two mechanisms positioned on opposite sides of a central tube to which an inert gas is fed. The two mechanisms and the wires being fed constitute electrodes to which electrical current is supplied so that the wires are melted by the electric are formed at their contacting region and sprayed by the gas supplied by the central tube. This apparatus is designed specifically to apply a zirconium coating to uranium in an inert atmosphere and without the use of an oxidizing flame.

Estimating the coordinates of pillars and posts in the parking lots for intelligent parking assist system

NASA Astrophysics Data System (ADS)

Choi, Jae Hyung; Kuk, Jung Gap; Kim, Young Il; Cho, Nam Ik

2012-01-01

This paper proposes an algorithm for the detection of pillars or posts in the video captured by a single camera implemented on the fore side of a room mirror in a car. The main purpose of this algorithm is to complement the weakness of current ultrasonic parking assist system, which does not well find the exact position of pillars or does not recognize narrow posts. The proposed algorithm is consisted of three steps: straight line detection, line tracking, and the estimation of 3D position of pillars. In the first step, the strong lines are found by the Hough transform. Second step is the combination of detection and tracking, and the third is the calculation of 3D position of the line by the analysis of trajectory of relative positions and the parameters of camera. Experiments on synthetic and real images show that the proposed method successfully locates and tracks the position of pillars, which helps the ultrasonic system to correctly locate the edges of pillars. It is believed that the proposed algorithm can also be employed as a basic element for vision based autonomous driving system.

Evolution of the cosmic web

NASA Astrophysics Data System (ADS)

Cautun, Marius; van de Weygaert, Rien; Jones, Bernard J. T.; Frenk, Carlos S.

2014-07-01

The cosmic web is the largest scale manifestation of the anisotropic gravitational collapse of matter. It represents the transitional stage between linear and non-linear structures and contains easily accessible information about the early phases of structure formation processes. Here we investigate the characteristics and the time evolution of morphological components. Our analysis involves the application of the NEXUS Multiscale Morphology Filter technique, predominantly its NEXUS+ version, to high resolution and large volume cosmological simulations. We quantify the cosmic web components in terms of their mass and volume content, their density distribution and halo populations. We employ new analysis techniques to determine the spatial extent of filaments and sheets, like their total length and local width. This analysis identifies clusters and filaments as the most prominent components of the web. In contrast, while voids and sheets take most of the volume, they correspond to underdense environments and are devoid of group-sized and more massive haloes. At early times the cosmos is dominated by tenuous filaments and sheets, which, during subsequent evolution, merge together, such that the present-day web is dominated by fewer, but much more massive, structures. The analysis of the mass transport between environments clearly shows how matter flows from voids into walls, and then via filaments into cluster regions, which form the nodes of the cosmic web. We also study the properties of individual filamentary branches, to find long, almost straight, filaments extending to distances larger than 100 h-1 Mpc. These constitute the bridges between massive clusters, which seem to form along approximatively straight lines.

Utilizing the ratio and the summation of two spectral lines for estimation of optical depth: Focus on thick plasmas

NASA Astrophysics Data System (ADS)

Rezaei, Fatemeh; Tavassoli, Seyed Hassan

2016-11-01

In this paper, a study is performed on the spectral lines of plasma radiations created from focusing of the Nd:YAG laser on Al standard alloys at atmospheric air pressure. A new theoretical method is presented to investigate the evolution of the optical depth of the plasma based on the radiative transfer equation, in LTE condition. This work relies on the Boltzmann distribution, lines broadening equations, and as well as the self-absorption relation. Then, an experimental set-up is devised to extract some of plasma parameters such as temperature from modified line ratio analysis, electron density from Stark broadening mechanism, line intensities of two spectral lines in the same order of ionization from similar species, and the plasma length from the shadowgraphy section. In this method, the summation and the ratio of two spectral lines are considered for evaluation of the temporal variations of the plasma parameters in a LIBS homogeneous plasma. The main advantage of this method is that it comprises the both of thin and thick laser induced plasmas without straight calculation of self-absorption coefficient. Moreover, the presented model can also be utilized for evaluation the transition of plasma from the thin condition to the thick one. The results illustrated that by measuring the line intensities of two spectral lines at different evolution times, the plasma cooling and the growth of the optical depth can be followed.

Finger vein recognition using local line binary pattern.

PubMed

Rosdi, Bakhtiar Affendi; Shing, Chai Wuh; Suandi, Shahrel Azmin

2011-01-01

In this paper, a personal verification method using finger vein is presented. Finger vein can be considered more secured compared to other hands based biometric traits such as fingerprint and palm print because the features are inside the human body. In the proposed method, a new texture descriptor called local line binary pattern (LLBP) is utilized as feature extraction technique. The neighbourhood shape in LLBP is a straight line, unlike in local binary pattern (LBP) which is a square shape. Experimental results show that the proposed method using LLBP has better performance than the previous methods using LBP and local derivative pattern (LDP).

Dielectric constants of soils at microwave frequencies-2

NASA Technical Reports Server (NTRS)

Wang, J.; Schmugge, T.; Williams, D.

1978-01-01

The dielectric constants of several soil samples were measured at frequencies of 5 and 19 GHz using the infinite transmission line method. The results of these measurements are presented and discussed with respect to soil types and texture structures. A comparison is made with other measurements at 1.4 GHz. At all three frequencies, the dependence of dielectric constant on soil moisture can be approximated by two straight lines. At low moisture, the slope is less than at high moisture level. The intersection of the two lines is believed to be a function of soil texture.

Flight-path estimation in passive low-altitude flight by visual cues

NASA Technical Reports Server (NTRS)

Grunwald, Arthur J.; Kohn, S.

1993-01-01

A series of experiments was conducted, in which subjects had to estimate the flight path while passively being flown in straight or in curved motion over several types of nominally flat, textured terrain. Three computer-generated terrain types were investigated: (1) a random 'pole' field, (2) a flat field consisting of random rectangular patches, and (3) a field of random parallelepipeds. Experimental parameters were the velocity-to-height (V/h) ratio, the viewing distance, and the terrain type. Furthermore, the effect of obscuring parts of the visual field was investigated. Assumptions were made about the basic visual-field information by analyzing the pattern of line-of-sight (LOS) rate vectors in the visual field. The experimental results support these assumptions and show that, for both a straight as well as a curved flight path, the estimation accuracy and estimation times improve with the V/h ratio. Error scores for the curved flight path are found to be about 3 deg in visual angle higher than for the straight flight path, and the sensitivity to the V/h ratio is found to be considerably larger. For the straight motion, the flight path could be estimated successfully from local areas in the far field. Curved flight-path estimates have to rely on the entire LOS rate pattern.

Trajectories of Listeria-type motility in two dimensions

NASA Astrophysics Data System (ADS)

Wen, Fu-Lai; Leung, Kwan-tai; Chen, Hsuan-Yi

2012-12-01

Force generated by actin polymerization is essential in cell motility and the locomotion of organelles or bacteria such as Listeria monocytogenes. Both in vivo and in vitro experiments on actin-based motility have observed geometrical trajectories including straight lines, circles, S-shaped curves, and translating figure eights. This paper reports a phenomenological model of an actin-propelled disk in two dimensions that generates geometrical trajectories. Our model shows that when the evolutions of actin density and force per filament on the disk are strongly coupled to the disk self-rotation, it is possible for a straight trajectory to lose its stability. When the instability is due to a pitchfork bifurcation, the resulting trajectory is a circle; a straight trajectory can also lose stability through a Hopf bifurcation, and the resulting trajectory is an S-shaped curve. We also show that a half-coated disk, which mimics the distribution of functionalized proteins in Listeria, also undergoes similar symmetry-breaking bifurcations when the straight trajectory loses stability. For both a fully coated disk and a half-coated disk, when the trajectory is an S-shaped curve, the angular frequency of the disk self-rotation is different from that of the disk trajectory. However, for circular trajectories, these angular frequencies are different for a fully coated disk but the same for a half-coated disk.

Office Skills: What Are the Effects of a Composition Emphasis during Two Semesters of Typewriting?

ERIC Educational Resources Information Center

Gades, Robert E.; Dougal, Barbara

1979-01-01

A study which compared the composition approach of typewriting instruction with the traditional approach found no significant difference in typewriting speed after one year of instruction. Students trained with the composition approach showed significantly fewer errors on straight-line timings. (LRA)

46 CFR 382.3 - Determination of fair and reasonable rate.

Code of Federal Regulations, 2014 CFR

2014-10-01

... capitalized improvements, shall be depreciated on a straight-line basis over a 20-year economic life, except... equal installments over the economic life of the vessels as determined in accordance with paragraph (b... that the vessel's constructed net book value, less outstanding constructed principal, is equity. The...

46 CFR 382.3 - Determination of fair and reasonable rate.

Code of Federal Regulations, 2013 CFR

2013-10-01

... capitalized improvements, shall be depreciated on a straight-line basis over a 20-year economic life, except... equal installments over the economic life of the vessels as determined in accordance with paragraph (b... that the vessel's constructed net book value, less outstanding constructed principal, is equity. The...

27 CFR 9.133 - Rutherford.

Code of Federal Regulations, 2014 CFR

2014-04-01

... proceeds in a southwesterly direction in a straight line approximately 1.7 miles along Skellenger Lane... miles to the point where an unnamed stream drains into the Napa River from the west; (3) Then along the... Southern Pacific Railroad Track; (4) Then southeasterly along said railroad track 1,650 feet to a point...

49 CFR 572.7 - Neck.

Code of Federal Regulations, 2014 CFR

2014-10-01

... paragraph (c) of this section, the head shall rotate in reference to the pendulum's longitudinal centerline... the straight line distance between (1) the position relative to the pendulum arm of the head center of gravity at time zero, and (2) the position relative to the pendulum arm of the head center of gravity at...

49 CFR 572.7 - Neck.

Code of Federal Regulations, 2012 CFR

2012-10-01

... paragraph (c) of this section, the head shall rotate in reference to the pendulum's longitudinal centerline... the straight line distance between (1) the position relative to the pendulum arm of the head center of gravity at time zero, and (2) the position relative to the pendulum arm of the head center of gravity at...

49 CFR 572.7 - Neck.

Code of Federal Regulations, 2013 CFR

2013-10-01

... paragraph (c) of this section, the head shall rotate in reference to the pendulum's longitudinal centerline... the straight line distance between (1) the position relative to the pendulum arm of the head center of gravity at time zero, and (2) the position relative to the pendulum arm of the head center of gravity at...

49 CFR 572.7 - Neck.

Code of Federal Regulations, 2010 CFR

2010-10-01

... paragraph (c) of this section, the head shall rotate in reference to the pendulum's longitudinal centerline... the straight line distance between (1) the position relative to the pendulum arm of the head center of gravity at time zero, and (2) the position relative to the pendulum arm of the head center of gravity at...

49 CFR 572.7 - Neck.

Code of Federal Regulations, 2011 CFR

2011-10-01

... paragraph (c) of this section, the head shall rotate in reference to the pendulum's longitudinal centerline... the straight line distance between (1) the position relative to the pendulum arm of the head center of gravity at time zero, and (2) the position relative to the pendulum arm of the head center of gravity at...

Multiple Teaching Approaches, Teaching Sequence and Concept Retention in High School Physics Education

ERIC Educational Resources Information Center

Fogarty, Ian; Geelan, David

2013-01-01

Students in 4 Canadian high school physics classes completed instructional sequences in two key physics topics related to motion--Straight Line Motion and Newton's First Law. Different sequences of laboratory investigation, teacher explanation (lecture) and the use of computer-based scientific visualizations (animations and simulations) were…

48 CFR 9904.406-61 - Interpretation.

Code of Federal Regulations, 2010 CFR

2010-10-01

... ACCOUNTING STANDARDS COST ACCOUNTING STANDARDS 9904.406-61 Interpretation. (a) Questions have arisen as to... categories of costs that have been included in the past and may be considered in the future as restructuring... restructuring costs shall not exceed five years. The straight-line method of amortization should normally be...

50 CFR 665.931 - Boundaries.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., Baker, Howland, and Jarvis Islands, Johnston Atoll, Kingman Reef, and Palmyra Atoll, is defined as...″ 0°28′39″ N. (d) Johnston Atoll. The Johnston Atoll unit of the Monument includes the waters and submerged and emergent lands around Johnston Atoll within an area defined by straight lines connecting the...

50 CFR 665.931 - Boundaries.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., Baker, Howland, and Jarvis Islands, Johnston Atoll, Kingman Reef, and Palmyra Atoll, is defined as...″ 0°28′39″ N. (d) Johnston Atoll. The Johnston Atoll unit of the Monument includes the waters and submerged and emergent lands around Johnston Atoll within an area defined by straight lines connecting the...

26 CFR 1.167(b)-1 - Straight line method.

Code of Federal Regulations, 2010 CFR

2010-04-01

... estimated useful life of the property. The allowance for depreciation for the taxable year is determined by... reasonable allowance for depreciation for any property which is subject to depreciation under section 167 and... or other basis less salaries Useful life (years) Depreciation allowable 1954 1955 1956 1954: Asset A...

27 CFR 9.210 - Lehigh Valley.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Lehigh River in the city of Jim Thorpe; then (8) Proceed east-northeasterly in a straight line to the... along Interstate 80 through Stroudsburg to the west bank of the Delaware River; then (15) Proceed south (downstream) along the west bank of the Delaware River, and, crossing onto the Northampton County map...

47 CFR 80.769 - Shadow loss.

Code of Federal Regulations, 2013 CFR

2013-10-01

... average terrain elevation at the coast station antenna to the water level at the ship location. If average... antenna site elevation, the obstruction elevation and the height of the ship station on rectangular... the horizontal scale. Then draw a straight line between the antenna and the ship. (c) If a hill...

47 CFR 80.769 - Shadow loss.

Code of Federal Regulations, 2011 CFR

2011-10-01

... average terrain elevation at the coast station antenna to the water level at the ship location. If average... antenna site elevation, the obstruction elevation and the height of the ship station on rectangular... the horizontal scale. Then draw a straight line between the antenna and the ship. (c) If a hill...

47 CFR 80.769 - Shadow loss.

Code of Federal Regulations, 2014 CFR

2014-10-01

... average terrain elevation at the coast station antenna to the water level at the ship location. If average... antenna site elevation, the obstruction elevation and the height of the ship station on rectangular... the horizontal scale. Then draw a straight line between the antenna and the ship. (c) If a hill...

47 CFR 80.769 - Shadow loss.

Code of Federal Regulations, 2012 CFR

2012-10-01

... average terrain elevation at the coast station antenna to the water level at the ship location. If average... antenna site elevation, the obstruction elevation and the height of the ship station on rectangular... the horizontal scale. Then draw a straight line between the antenna and the ship. (c) If a hill...

40 CFR 89.322 - Carbon dioxide analyzer calibration.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Test Equipment Provisions § 89.322 Carbon dioxide analyzer calibration. (a) Prior to its introduction... requirements of paragraph (a)(3) of this section. Proceed as follows: (1) Follow good engineering practices for... engineering practice. For each range calibrated, if the deviation from a least-squares best-fit straight line...

40 CFR 85.2114 - Basis of certification.

Code of Federal Regulations, 2014 CFR

2014-07-01

... calculated using the least squares straight line method, in accordance with § 86.088-28(a). The deterioration... requirements of this paragraph for at least the part's useful life mileage interval. (i) If an original... the aftermarket parts that accumulated at least its useful life mileage during the aging process under...

40 CFR 85.2114 - Basis of certification.

Code of Federal Regulations, 2012 CFR

2012-07-01

... calculated using the least squares straight line method, in accordance with § 86.088-28(a). The deterioration... requirements of this paragraph for at least the part's useful life mileage interval. (i) If an original... the aftermarket parts that accumulated at least its useful life mileage during the aging process under...

40 CFR 85.2114 - Basis of certification.

Code of Federal Regulations, 2011 CFR

2011-07-01

... calculated using the least squares straight line method, in accordance with § 86.088-28(a). The deterioration... requirements of this paragraph for at least the part's useful life mileage interval. (i) If an original... the aftermarket parts that accumulated at least its useful life mileage during the aging process under...

40 CFR 85.2114 - Basis of certification.

Code of Federal Regulations, 2013 CFR

2013-07-01

... calculated using the least squares straight line method, in accordance with § 86.088-28(a). The deterioration... requirements of this paragraph for at least the part's useful life mileage interval. (i) If an original... the aftermarket parts that accumulated at least its useful life mileage during the aging process under...

86. Round Meadow Creek Viaduct. This steel girder bridge, built ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

86. Round Meadow Creek Viaduct. This steel girder bridge, built in 1939, has a reinforced concrete deck and piers. It is an example of a major in-line, or straight, viaduct over a deep ravine. - Blue Ridge Parkway, Between Shenandoah National Park & Great Smoky Mountains, Asheville, Buncombe County, NC

40 CFR 89.319 - Hydrocarbon analyzer calibration.

Code of Federal Regulations, 2013 CFR

2013-07-01

... each range calibrated, if the deviation from a least-squares best-fit straight line is 2 percent or... ±0.3 percent of full scale on the zero, the best-fit non-linear equation which represents the data to within these limits shall be used to determine concentration. (d) Oxygen interference optimization...

40 CFR 89.319 - Hydrocarbon analyzer calibration.

Code of Federal Regulations, 2014 CFR

2014-07-01

... each range calibrated, if the deviation from a least-squares best-fit straight line is 2 percent or... ±0.3 percent of full scale on the zero, the best-fit non-linear equation which represents the data to within these limits shall be used to determine concentration. (d) Oxygen interference optimization...

40 CFR 89.319 - Hydrocarbon analyzer calibration.

Code of Federal Regulations, 2012 CFR

2012-07-01

... each range calibrated, if the deviation from a least-squares best-fit straight line is 2 percent or... ±0.3 percent of full scale on the zero, the best-fit non-linear equation which represents the data to within these limits shall be used to determine concentration. (d) Oxygen interference optimization...

40 CFR 89.320 - Carbon monoxide analyzer calibration.

Code of Federal Regulations, 2014 CFR

2014-07-01

... monoxide as described in this section. (b) Initial and periodic interference check. Prior to its... engineering practice. For each range calibrated, if the deviation from a least-squares best-fit straight line... range. If the deviation exceeds these limits, the best-fit non-linear equation which represents the data...

40 CFR 89.320 - Carbon monoxide analyzer calibration.

Code of Federal Regulations, 2013 CFR

2013-07-01

... monoxide as described in this section. (b) Initial and periodic interference check. Prior to its... engineering practice. For each range calibrated, if the deviation from a least-squares best-fit straight line... range. If the deviation exceeds these limits, the best-fit non-linear equation which represents the data...

40 CFR 89.320 - Carbon monoxide analyzer calibration.

Code of Federal Regulations, 2012 CFR

2012-07-01

... monoxide as described in this section. (b) Initial and periodic interference check. Prior to its... engineering practice. For each range calibrated, if the deviation from a least-squares best-fit straight line... range. If the deviation exceeds these limits, the best-fit non-linear equation which represents the data...

40 CFR 89.320 - Carbon monoxide analyzer calibration.

Code of Federal Regulations, 2011 CFR

2011-07-01

... monoxide as described in this section. (b) Initial and periodic interference check. Prior to its... engineering practice. For each range calibrated, if the deviation from a least-squares best-fit straight line... range. If the deviation exceeds these limits, the best-fit non-linear equation which represents the data...

75 FR 25815 - Disadvantaged Business Enterprise: Program Improvements

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-10

... extent, the purpose of the three-year goal submission interval. We anticipate that this approach would be... approaches to making inflationary adjustments. The Department seeks comment on whether the straight-line CPI approach used in the NPRM is appropriate, or whether there are other approaches or techniques that would be...

The Shoemaker's Knife

ERIC Educational Resources Information Center

Thomson, Ian

2010-01-01

Archimedes, the famous Greek mathematician, lived from 287 BCE until approximately 212 BCE. He thought that the figure of two semi-circles on a straight line enclosed by a larger semi-circle resembled a shoemaker's knife. Archimedes called this figure an "arbelos" since arbelos is the Greek word for a shoemaker's knife. The author describes the…

46 CFR 115.900 - Applicability.

Code of Federal Regulations, 2012 CFR

2012-10-01

... International Convention for Safety of Life at Sea, 1974, as Amended (SOLAS) § 115.900 Applicability. (a) Except... applicable requirements of the International Convention for Safety of Life at Sea, 1974, as Amended (SOLAS... solely navigating the Great Lakes and the St. Lawrence River as far east as a straight line drawn from...

46 CFR 115.900 - Applicability.

Code of Federal Regulations, 2014 CFR

2014-10-01

... International Convention for Safety of Life at Sea, 1974, as Amended (SOLAS) § 115.900 Applicability. (a) Except... applicable requirements of the International Convention for Safety of Life at Sea, 1974, as Amended (SOLAS... solely navigating the Great Lakes and the St. Lawrence River as far east as a straight line drawn from...

46 CFR 115.900 - Applicability.

Code of Federal Regulations, 2013 CFR

2013-10-01

... International Convention for Safety of Life at Sea, 1974, as Amended (SOLAS) § 115.900 Applicability. (a) Except... applicable requirements of the International Convention for Safety of Life at Sea, 1974, as Amended (SOLAS... solely navigating the Great Lakes and the St. Lawrence River as far east as a straight line drawn from...

46 CFR 115.900 - Applicability.

Code of Federal Regulations, 2011 CFR

2011-10-01

... International Convention for Safety of Life at Sea, 1974, as Amended (SOLAS) § 115.900 Applicability. (a) Except... applicable requirements of the International Convention for Safety of Life at Sea, 1974, as Amended (SOLAS... solely navigating the Great Lakes and the St. Lawrence River as far east as a straight line drawn from...

Food Service: How and What to Plan.

ERIC Educational Resources Information Center

Buchanan, Robert D.

1962-01-01

The effectiveness of food service facilities will be greatly enhanced by--(1) developing operating policies early in the design stage, (2) translating menus and recipes into space, time, amounts, and equipment, (3) arranging kitchen functions and work centers into straight line flow, and (4) evaluation. Operating policies and procedures must be…

Microwave focusators

NASA Astrophysics Data System (ADS)

Vinogradov, E. A.; Gridin, S. A.; Golovanov, V. I.; Danilenko, A. A.; Bulatov, E. D.

1989-01-01

A system capable of focusing monochromatic microwave radiation with a spherical or planar wavefront into a straight line segment is designed. The system consists of zone elements made with numerically controlled machine tools. The study of the image obtained revealed that the width of the formed local segment is close to the diffraction limit.

Application of remote sensing techniques to hydrography with emphasis on bathymetry. M.S. Thesis

NASA Technical Reports Server (NTRS)

Dejesusparada, N. (Principal Investigator); Meireles, D. S.

1980-01-01

Remote sensing techniques are utilized for the determination of hydrographic characteristics, with emphasis in bathymetry. Two sensor systems were utilized: the Metric Camera Wild RC-10 and the Multispectral Scanner of LANDSAT Satellite (MSS-LANDSAT). From photographs of the metric camera, data of photographic density of points with known depth are obtained. A correlation between the variables density x depth is calculated through a regression straight line. From this line, the depth of points with known photographic density is determined. The LANDSAT MSS images are interpreted automatically in the Iterative Multispectral Analysis System (I-100) with the obtention of point subareas with the same gray level. With some simplifications done, it is assumed that the depth of a point is directly related with its gray level. Subareas with points of the same depth are then determined and isobathymetric curves are drawn. The coast line is obtained through the sensor systems already mentioned. Advantages and limitations of the techniques and of the sensor systems utilized are discussed and the results are compared with ground truth.

Volatile profiles of members of the USDA Geneva Malus Core Collection: utility in evaluation of a hypothesized biosynthetic pathway for esters derived from 2-methylbutanoate and 2-methylbutan-1-ol.

PubMed

Sugimoto, Nobuko; Forsline, Philip; Beaudry, Randolph

2015-02-25

The volatile ester and alcohol profiles of ripening apple fruit from 184 germplasm lines in the USDA Malus Germplasm Repository at the New York Agricultural Experiment Station in Geneva, NY, USA, were evaluated. Cluster analysis suggested biochemical relationships exist between several ester classes. A strong linkage was revealed between 2-methylbutanoate, propanoate, and butanoate esters, suggesting the influence of the recently proposed "citramalic acid pathway" in apple fruit. Those lines with a high content of esters formed from 2-methylbutan-1-ol and 2-methylbutanoate (2MB) relative to straight-chain (SC) esters (high 2MB/SC ratio) exhibited a marked increase in isoleucine and citramalic acid during ripening, but those lines with a low content did not. Thus, the data were consistent with the existence of the hypothesized citramalic acid pathway and suggest that the Geneva Malus Germplasm Repository, appropriately used, could be helpful in expanding our understanding of mechanisms for fruit volatile synthesis and other aspects of secondary metabolism.

Model atmospheres for cool stars. [varying chemical composition

NASA Technical Reports Server (NTRS)

Johnson, H. R.

1974-01-01

This report contains an extensive series of model atmospheres for cool stars having a wide range in chemical composition. Model atmospheres (temperature, pressure, density, etc.) are tabulated, along with emergent energy flux distributions, limb darkening, and information on convection for selected models. The models are calculated under the usual assumptions of hydrostatic equilibrium, constancy of total energy flux (including transport both by radiation and convection) and local thermodynamic equilibrium. Some molecular and atomic line opacity is accounted for as a straight mean. While cool star atmospheres are regimes of complicated physical conditions, and these atmospheres are necessarily approximate, they should be useful for a number of kinds of spectral and atmospheric analysis.

Modeling of outgassing and matrix decomposition in carbon-phenolic composites

NASA Technical Reports Server (NTRS)

Mcmanus, Hugh L.

1993-01-01

A new release rate equation to model the phase change of water to steam in composite materials was derived from the theory of molecular diffusion and equilibrium moisture concentration. The new model is dependent on internal pressure, the microstructure of the voids and channels in the composite materials, and the diffusion properties of the matrix material. Hence, it is more fundamental and accurate than the empirical Arrhenius rate equation currently in use. The model was mathematically formalized and integrated into the thermostructural analysis code CHAR. Parametric studies on variation of several parameters have been done. Comparisons to Arrhenius and straight-line models show that the new model produces physically realistic results under all conditions.

Stress Intensity Factors of Semi-Circular Bend Specimens with Straight-Through and Chevron Notches

NASA Astrophysics Data System (ADS)

Ayatollahi, M. R.; Mahdavi, E.; Alborzi, M. J.; Obara, Y.

2016-04-01

Semi-circular bend specimen is one of the useful test specimens for determining fracture toughness of rock and geo-materials. Generally, in rock test specimens, initial cracks are produced in two shapes: straight-edge cracks and chevron notches. In this study, the minimum dimensionless stress intensity factors of semi-circular bend specimen (SCB) with straight-through and chevron notches are calculated. First, using finite element analysis, a suitable relation for the dimensionless stress intensity factor of SCB with straight-through crack is presented based on the normalized crack length and half-distance between supports. For evaluating the validity and accuracy of this relation, the obtained results are then compared with numerical and experimental results reported in the literature. Subsequently, by performing some experiments and also finite element analysis of the SCB specimen with chevron notch, the minimum dimensionless stress intensity factor of this specimen is obtained. Using the new equation for the dimensionless stress intensity factor of SCB with straight-through crack and an analytical method, i.e., Bluhm's slice synthesis method, the minimum (critical) dimensionless stress intensity factor of chevron notched semi-circular bend specimens is calculated. Good agreement is observed between the results of two mentioned methods.

Single-Camera-Based Method for Step Length Symmetry Measurement in Unconstrained Elderly Home Monitoring.

PubMed

Cai, Xi; Han, Guang; Song, Xin; Wang, Jinkuan

2017-11-01

single-camera-based gait monitoring is unobtrusive, inexpensive, and easy-to-use to monitor daily gait of seniors in their homes. However, most studies require subjects to walk perpendicularly to camera's optical axis or along some specified routes, which limits its application in elderly home monitoring. To build unconstrained monitoring environments, we propose a method to measure step length symmetry ratio (a useful gait parameter representing gait symmetry without significant relationship with age) from unconstrained straight walking using a single camera, without strict restrictions on walking directions or routes. according to projective geometry theory, we first develop a calculation formula of step length ratio for the case of unconstrained straight-line walking. Then, to adapt to general cases, we propose to modify noncollinear footprints, and accordingly provide general procedure for step length ratio extraction from unconstrained straight walking. Our method achieves a mean absolute percentage error (MAPE) of 1.9547% for 15 subjects' normal and abnormal side-view gaits, and also obtains satisfactory MAPEs for non-side-view gaits (2.4026% for 45°-view gaits and 3.9721% for 30°-view gaits). The performance is much better than a well-established monocular gait measurement system suitable only for side-view gaits with a MAPE of 3.5538%. Independently of walking directions, our method can accurately estimate step length ratios from unconstrained straight walking. This demonstrates our method is applicable for elders' daily gait monitoring to provide valuable information for elderly health care, such as abnormal gait recognition, fall risk assessment, etc. single-camera-based gait monitoring is unobtrusive, inexpensive, and easy-to-use to monitor daily gait of seniors in their homes. However, most studies require subjects to walk perpendicularly to camera's optical axis or along some specified routes, which limits its application in elderly home monitoring. To build unconstrained monitoring environments, we propose a method to measure step length symmetry ratio (a useful gait parameter representing gait symmetry without significant relationship with age) from unconstrained straight walking using a single camera, without strict restrictions on walking directions or routes. according to projective geometry theory, we first develop a calculation formula of step length ratio for the case of unconstrained straight-line walking. Then, to adapt to general cases, we propose to modify noncollinear footprints, and accordingly provide general procedure for step length ratio extraction from unconstrained straight walking. Our method achieves a mean absolute percentage error (MAPE) of 1.9547% for 15 subjects' normal and abnormal side-view gaits, and also obtains satisfactory MAPEs for non-side-view gaits (2.4026% for 45°-view gaits and 3.9721% for 30°-view gaits). The performance is much better than a well-established monocular gait measurement system suitable only for side-view gaits with a MAPE of 3.5538%. Independently of walking directions, our method can accurately estimate step length ratios from unconstrained straight walking. This demonstrates our method is applicable for elders' daily gait monitoring to provide valuable information for elderly health care, such as abnormal gait recognition, fall risk assessment, etc.

Autonomous Unmanned Aerial Vehicle Rendezvous for Automated Aerial Refueling

DTIC Science & Technology

2007-03-01

represents a straight line segment. It can be seen that there are ten possible combinations of arcs and line segments (RSR, RSL, LSR, LSL, LRL, RLR , SLR...SRL, RLS, and LRS). However, L. E. Dubins proved that only these six sequences are possibly optimal: RSR, RSL, LSR, LSL, LRL, and RLR [Dubins 1957...From Figure 2-5 and Figure 2-6, it can be seen that the last two cases, RLR and LRL can only be optimal when the initial point and the terminal

Flood Plain Information Brandywine Creek, New Castle County, Delaware.

DTIC Science & Technology

1973-07-01

The Brandywine’s course through Delaware is fairly straight and cuts through a valley of rugged terrain. The adjacent land slopes that comprise its...varies sharply in 3 distinct reaches. The upper reach from the State Line to Rockland Road falls 15.5 feet at a slope of 4.9 feet per mile. The middle...Mileage Above Drainage Area Location Mouth Tributary Total sq. Mi. sq. mi. Pennsy lvania-Del aware State Line 10.55 ... 299.9 Confluence with Beaver

TRISTEN/FRAM II Cruise Report, East Arctic, April 1980.

DTIC Science & Technology

1981-04-13

is not readily accessible by air from Alaska. The Eurasia Basin contains the Arctic Midoceanic Ridge, which extends in a straight line for 2000 km...13 6 Bottom Refraction - Shot- Lines Overlain on FRAM II Positions 14 7 Waterfall Display of Successive Spectral Estimates of Single...Northeast leg of the array was oriented 341T and the NW leg 304 ’T. After a windstorm and flow break-up on 16 April, hydrophones 11 and 12 and 21-24 were

Applications of Advanced Experimental Methods to Visual Technology Research Simulator Studies: Supplemental Techniques.

DTIC Science & Technology

1981-01-01

straight line. Those that are larger than might be expected by chance will deviate i.oticeably from the line. Wilk and Gnanadesikan (1964; also see Roy... Gnanadesikan , and Srivasta, 1971, Chapter VIII; also see Simon, 1977a, pp 151-158 for a general description of the procedure) describe how to use a...by Wilk and Gnanadesikan is rather involved and is explained in matrix algebra terms, it is described b-low along with an example to facilitate its

Symbolic Image Understanding

DTIC Science & Technology

1991-11-01

publication. APPROVED: a LEE A. UVANNI Project Engineer FOR THE COMMANDER: GARRY W. BARRINGER Technical Director Intelligence & Reconnaissance...f Od1cAtl nd ir-’bm a UNl tofU~rtaw ."t Pu’ o scrxr± ing twra fa revrl r Jt,= seagrg d un zla souLces gahwtW" r T , iUm rm , rruk4 c adiwvctws coa w...1990j matches straight lines extracted from an image with model lines r projected to the image plane using an assumed location of the camera. This

AITRAC: Augmented Interactive Transient Radiation Analysis by Computer. User's information manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1977-10-01

AITRAC is a program designed for on-line, interactive, DC, and transient analysis of electronic circuits. The program solves linear and nonlinear simultaneous equations which characterize the mathematical models used to predict circuit response. The program features 100 external node--200 branch capability; conversional, free-format input language; built-in junction, FET, MOS, and switch models; sparse matrix algorithm with extended-precision H matrix and T vector calculations, for fast and accurate execution; linear transconductances: beta, GM, MU, ZM; accurate and fast radiation effects analysis; special interface for user-defined equations; selective control of multiple outputs; graphical outputs in wide and narrow formats; and on-line parametermore » modification capability. The user describes the problem by entering the circuit topology and part parameters. The program then automatically generates and solves the circuit equations, providing the user with printed or plotted output. The circuit topology and/or part values may then be changed by the user, and a new analysis, requested. Circuit descriptions may be saved on disk files for storage and later use. The program contains built-in standard models for resistors, voltage and current sources, capacitors, inductors including mutual couplings, switches, junction diodes and transistors, FETS, and MOS devices. Nonstandard models may be constructed from standard models or by using the special equations interface. Time functions may be described by straight-line segments or by sine, damped sine, and exponential functions. 42 figures, 1 table. (RWR)« less

Incidents between Straight-ahead Cyclists and Right-turning Motor Vehicles at Signalised Junctions.

PubMed

Buch, Thomas Skallebæk; Jensen, Søren Underlien

2017-08-01

Accidents between right-turning motor vehicles and straight-ahead cyclists are one of the most common accident types leading to cyclist injuries at signalised junctions in Denmark. A before-after safety evaluation of applying staggered stop lines in 189 arms at 123 signalised junctions is presented. The evaluation accounts for long-term accident trends and changes in motor vehicle traffic volumes. Applying staggered stop lines gives no decline in accidents between right-turning motor vehicles and straight-ahead cyclists. However, there is a statistical tendency to a decline of these right-turn accidents involving heavy vehicles. There are several questions about factors leading to right-turn accidents that cannot be answered by recorded accident data. A study of conflicting behaviour focuses on factors leading to conflicts. Video observations have been carried out in 10 arms at signalised junctions. A total of 45 situations with conflicting behaviour between right-turning motor vehicles and straight-ahead cyclists have been investigated and compared to a reference group of simultaneous arrivals. The relative risk is lowest when both parties stop on red before entering the junction. Upon simultaneous arrival of both parties at a green light, the relative risk is highest. Cyclists tend to have a higher relative risk of being involved in conflicts if they; a) ride through on yellow, b) have a time distance of at least 2seconds to other cyclists, c) wear a black jacket, and/or d) arrive at the junction at a speed of at least 25km/h. Much less can be said about the motor vehicles or their drivers on the basis of these video observations, but motor vehicles stopping in the cycle crossing in order to yield to pedestrians or cyclists have a higher relative risk of being involved in conflicts. Copyright © 2016 Elsevier Ltd. All rights reserved.

Cross-ply laminates with holes in compression - Straight free-edge stresses determined by two- to three-dimensional global/local finite element analysis

NASA Technical Reports Server (NTRS)

Thompson, Danniella Muheim; Griffin, O. Hayden, Jr.; Vidussoni, Marco A.

1990-01-01

A practical example of applying two- to three-dimensional (2- to 3-D) global/local finite element analysis to laminated composites is presented. Cross-ply graphite/epoxy laminates of 0.1-in. (0.254-cm) thickness with central circular holes ranging from 1 to 6 in. (2.54 to 15.2 cm) in diameter, subjected to in-plane compression were analyzed. Guidelines for full three-dimensional finite element analysis and two- to three-dimensional global/local analysis of interlaminar stresses at straight free edges of laminated composites are included. The larger holes were found to reduce substantially the interlaminar stresses at the straight free-edge in proximity to the hole. Three-dimensional stress results were obtained for thin laminates which require prohibitive computer resources for full three-dimensional analyses of comparative accuracy.

Performance of a superconducting magnet system operated in the Super Omega Muon beam line at J-PARC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Makida, Yasuhiro; Ikedo, Yutaka; Ogitsu, Toru

A superconducting magnet system, which is composed of an 8 m long solenoid for transportation and 12 short solenoids for focusing, has been developed for Muon Science Establishment facility of J-PARC. The transport solenoid is composed of a 6 m straight section connected to a 45 degree curved section at each end. Muons of various momenta and of both electric charges are transported through the solenoid inner bore with an effective diameter of 0.3 m, where 2 T magnetic field is induced. There are 12 focusing solenoids with an effective bore diameter of 0.6 m and a length of 0.35more » m arranged on a straight line at suitable intervals. The maximum central field of each focusing solenoid is 0.66 T. All solenoid coils are cooled by GM cryocoolers through their own conductions. The magnet system has been installed into the beam line in the summer of 2012, and its performance has been checked. Beam commissioning has been carried out since October 2012. During beam operation, temperature rise over 6 K in the transport solenoid due to a nuclear heating from the muon production target is observed at beam intensity of about 300 kW.« less

Nothing more than a pair of curvatures: A common mechanism for the detection of both radial and non-radial frequency patterns.

PubMed

Schmidtmann, Gunnar; Kingdom, Frederick A A

2017-05-01

Radial frequency (RF) patterns, which are sinusoidal modulations of a radius in polar coordinates, are commonly used to study shape perception. Previous studies have argued that the detection of RF patterns is either achieved globally by a specialized global shape mechanism, or locally using as cue the maximum tangent orientation difference between the RF pattern and the circle. Here we challenge both ideas and suggest instead a model that accounts not only for the detection of RF patterns but also for line frequency patterns (LF), i.e. contours sinusoidally modulated around a straight line. The model has two features. The first is that the detection of both RF and LF patterns is based on curvature differences along the contour. The second is that this curvature metric is subject to what we term the Curve Frequency Sensitivity Function, or CFSF, which is characterized by a flat followed by declining response to curvature as a function of modulation frequency, analogous to the modulation transfer function of the eye. The evidence that curvature forms the basis for detection is that at very low modulation frequencies (1-3 cycles for the RF pattern) there is a dramatic difference in thresholds between the RF and LF patterns, a difference however that disappears at medium and high modulation frequencies. The CFSF feature on the other hand explains why thresholds, rather than continuously declining with modulation frequency, asymptote at medium and high modulation frequencies. In summary, our analysis suggests that the detection of shape modulations is processed by a common curvature-sensitive mechanism that is subject to a shape-frequency-dependent transfer function. This mechanism is independent of whether the modulation is applied to a circle or a straight line. Copyright © 2017 Elsevier Ltd. All rights reserved.

"Appearance potent"? A content analysis of UK gay and straight men's magazines.

PubMed

Jankowski, Glen S; Fawkner, Helen; Slater, Amy; Tiggemann, Marika

2014-09-01

With little actual appraisal, a more 'appearance potent' (i.e., a reverence for appearance ideals) subculture has been used to explain gay men's greater body dissatisfaction in comparison to straight men's. This study sought to assess the respective appearance potency of each subculture by a content analysis of 32 issues of the most read gay (Attitude, Gay Times) and straight men's magazines (Men's Health, FHM) in the UK. Images of men and women were coded for their physical characteristics, objectification and nudity, as were the number of appearance adverts and articles. The gay men's magazines featured more images of men that were appearance ideal, nude and sexualized than the straight men's magazines. The converse was true for the images of women and appearance adverts. Although more research is needed to understand the effect of this content on the viewer, the findings are consistent with a more appearance potent gay male subculture. Crown Copyright © 2014. Published by Elsevier Ltd. All rights reserved.

Astronaut Scott Carpenter tests balance mechanism performance

NASA Technical Reports Server (NTRS)

1961-01-01

Astronaut M. Scott Carpenter's balance mechanism performance is tested by his walking on a narrow board in his bare feet. He is performing this test at the School of Aviation Medicine, Pensicola, Florida (04570); Carpenter walks a straight line by putting one foot directly in front of the other to test his balance (04571).

Construction of Mathematical Definitions: An Epistemological and Didactical Study

ERIC Educational Resources Information Center

Ouvrier-Buffet, Cecile

2004-01-01

The definition-construction process is central to mathematics. The aim of this paper is to propose a few Situations of Definition-Construction (called SDC) and to study them. Our main objectives are to describe the definition-construction process and to design SDC for classroom. A SDC on "discrete straight line" and its mathematical and…

Calculus, Radio Dials and the Straight-Line Frequency Variable Capacitor

ERIC Educational Resources Information Center

Boyadzhiev, Khristo N.

2010-01-01

Most often radio dials of analogue radios are not uniformly graded; the frequencies are cramped on the left side or on the right side. This makes tuning more difficult. Why are dials made this way? We shall see here that simple calculus can help understand this problem and solve it. (Contains 7 figures.)

78 FR 59045 - Missouri; Major Disaster and Related Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-25

..., straight-line winds, and flooding during the period of August 2-14, 2013, is of sufficient severity and... limited to 75 percent of the total eligible costs. Federal funds provided under the Stafford Act for Public Assistance also will be limited to 75 percent of the total eligible costs, with the exception of...

78 FR 67383 - Kansas; Major Disaster and Related Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-12

..., straight-line winds, tornadoes, and flooding during the period of July 22 to August 16, 2013, is of... Hazard Mitigation will be limited to 75 percent of the total eligible costs. Federal funds provided under the Stafford Act for Public Assistance also will be limited to 75 percent of the total eligible costs...

75 FR 51837 - Tennessee; Amendment No. 11 to Notice of a Major Disaster Declaration

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-23

... Supplemental Appropriations Act, 2010, Public Law 111-212, FEMA is amending the cost-sharing arrangement... of Tennessee due to the damage resulting from severe storms, flooding, straight-line winds, and... declaration are authorized at 90 percent of total eligible costs. (The following Catalog of Federal Domestic...

50 CFR 223.207 - Approved TEDs.

Code of Federal Regulations, 2014 CFR

2014-10-01

... wet or dry. Any such measurement will be of the stretched mesh size. (a) Hard TEDs. Hard TEDs are TEDs.... The resultant escape opening with a webbing flap must have a stretched mesh circumference of no less... used when making the side cuts. The sum of the straight-line base measurement and the stretched...

50 CFR 223.207 - Approved TEDs.

Code of Federal Regulations, 2012 CFR

2012-10-01

... wet or dry. Any such measurement will be of the stretched mesh size. (a) Hard TEDs. Hard TEDs are TEDs.... The resultant escape opening with a webbing flap must have a stretched mesh circumference of no less... used when making the side cuts. The sum of the straight-line base measurement and the stretched...

50 CFR 223.207 - Approved TEDs.

Code of Federal Regulations, 2013 CFR

2013-10-01

... wet or dry. Any such measurement will be of the stretched mesh size. (a) Hard TEDs. Hard TEDs are TEDs.... The resultant escape opening with a webbing flap must have a stretched mesh circumference of no less... used when making the side cuts. The sum of the straight-line base measurement and the stretched...

John Dewey on Listening and Friendship in School and Society

ERIC Educational Resources Information Center

Waks, Leonard J.

2011-01-01

In this essay, Leonard Waks examines John Dewey's account of listening, drawing on Dewey's writings to establish a direct connection in his work between listening and democracy. Waks devotes the first part of the essay to explaining Dewey's distinction between one-way or straight-line listening and transactional listening-in-conversation, and to…

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reister, D.B.

This paper uses the Pontryagin maximum principle to find time optimal paths for a constant speed unicycle. The time optimal paths consist of sequences of arcs of circles and straight lines. The maximum principle introduced concepts (dual variables, bang-bang solutions, singular solutions, and transversality conditions) that provide important insight into the nature of the time optimal paths. 10 refs., 6 figs.

Linearization: Students Forget the Operating Point

ERIC Educational Resources Information Center

Roubal, J.; Husek, P.; Stecha, J.

2010-01-01

Linearization is a standard part of modeling and control design theory for a class of nonlinear dynamical systems taught in basic undergraduate courses. Although linearization is a straight-line methodology, it is not applied correctly by many students since they often forget to keep the operating point in mind. This paper explains the topic and…

Reconstruction of flux coordinates from discretized magnetic field maps

NASA Astrophysics Data System (ADS)

Predebon, I.; Momo, B.; Suzuki, Y.; Auriemma, F.

2018-04-01

We provide a simple method to build a straight field-line coordinate system from discretized (Poincaré) magnetic field maps. The method is suitable for any plasma domain with nested flux surfaces, including magnetic islands. Illustrative examples are shown for tokamak, heliotron, and reversed-field-pinch plasmas with m = 1 islands.

40 CFR 89.324 - Calibration of other equipment.

Code of Federal Regulations, 2011 CFR

2011-07-01

... and operation. Adjust the analyzer to optimize performance. (2) Zero the methane analyzer with zero...-fit straight line is 2 percent or less of the value at each non-zero data point and within ± 0.3 percent of full scale on the zero, concentration values may be calculated by use of a single calibration...

40 CFR 89.324 - Calibration of other equipment.

Code of Federal Regulations, 2013 CFR

2013-07-01

... and operation. Adjust the analyzer to optimize performance. (2) Zero the methane analyzer with zero...-fit straight line is 2 percent or less of the value at each non-zero data point and within ± 0.3 percent of full scale on the zero, concentration values may be calculated by use of a single calibration...

40 CFR 89.324 - Calibration of other equipment.

Code of Federal Regulations, 2012 CFR

2012-07-01

... and operation. Adjust the analyzer to optimize performance. (2) Zero the methane analyzer with zero...-fit straight line is 2 percent or less of the value at each non-zero data point and within ± 0.3 percent of full scale on the zero, concentration values may be calculated by use of a single calibration...

40 CFR 89.324 - Calibration of other equipment.

Code of Federal Regulations, 2014 CFR

2014-07-01

... and operation. Adjust the analyzer to optimize performance. (2) Zero the methane analyzer with zero...-fit straight line is 2 percent or less of the value at each non-zero data point and within ± 0.3 percent of full scale on the zero, concentration values may be calculated by use of a single calibration...

Comprehension for What? Preparing Students for Their Meaningful Future

ERIC Educational Resources Information Center

Conley, Mark W.; Wise, Antoinette

2011-01-01

Researchers, policymakers, and educators face a daunting task these days concerning literacy education for the here and now and literacy for the future. Even though one clings to the romantic notion that education provides the building blocks in a straight line to a meaningful future, the reality is that mixed goals and instructional messages…

40 CFR 86.1324-84 - Carbon dioxide analyzer calibration.

Code of Federal Regulations, 2013 CFR

2013-07-01

... calibrated, if the deviation from a least-squares best-fit straight line is within ±2 percent or less of the... exceeds these limits, then the best-fit non-linear equation which represents the data within these limits shall be used to determine concentration values. (d) The initial and periodic interference, system check...

40 CFR 91.316 - Hydrocarbon analyzer calibration.

Code of Federal Regulations, 2014 CFR

2014-07-01

... deviation from a least-squares best-fit straight line is two percent or less of the value at each data point... exceeds two percent at any point, use the best-fit non-linear equation which represents the data to within two percent of each test point to determine concentration. (d) Oxygen interference optimization...

40 CFR 89.322 - Carbon dioxide analyzer calibration.

Code of Federal Regulations, 2011 CFR

2011-07-01

... engineering practice. For each range calibrated, if the deviation from a least-squares best-fit straight line... range. If the deviation exceeds these limits, the best-fit non-linear equation which represents the data... interference, system check, and calibration test procedures specified in 40 CFR part 1065 may be used in lieu...

40 CFR 90.316 - Hydrocarbon analyzer calibration.

Code of Federal Regulations, 2012 CFR

2012-07-01

... from a least-squares best-fit straight line is two percent or less of the value at each data point... exceeds two percent at any point, use the best-fit non-linear equation which represents the data to within two percent of each test point to determine concentration. (d) Oxygen interference optimization. Prior...

40 CFR 86.123-78 - Oxides of nitrogen analyzer calibration.

Code of Federal Regulations, 2012 CFR

2012-07-01

...-squares best-fit straight line is 2 percent or less of the value at each data point, concentration values... percent at any point, the best-fit non-linear equation which represents the data to within 2 percent of... may be necessary to clean the analyzer frequently to prevent interference with NOX measurements (see...

40 CFR 86.123-78 - Oxides of nitrogen analyzer calibration.

Code of Federal Regulations, 2014 CFR

2014-07-01

...-squares best-fit straight line is 2 percent or less of the value at each data point, concentration values... percent at any point, the best-fit non-linear equation which represents the data to within 2 percent of... may be necessary to clean the analyzer frequently to prevent interference with NOX measurements (see...

40 CFR 86.123-78 - Oxides of nitrogen analyzer calibration.

Code of Federal Regulations, 2013 CFR

2013-07-01

...-squares best-fit straight line is 2 percent or less of the value at each data point, concentration values... percent at any point, the best-fit non-linear equation which represents the data to within 2 percent of... may be necessary to clean the analyzer frequently to prevent interference with NOX measurements (see...

40 CFR 86.1324-84 - Carbon dioxide analyzer calibration.

Code of Federal Regulations, 2012 CFR

2012-07-01

... calibrated, if the deviation from a least-squares best-fit straight line is within ±2 percent or less of the... exceeds these limits, then the best-fit non-linear equation which represents the data within these limits shall be used to determine concentration values. (d) The initial and periodic interference, system check...

40 CFR 90.316 - Hydrocarbon analyzer calibration.

Code of Federal Regulations, 2013 CFR

2013-07-01

... from a least-squares best-fit straight line is two percent or less of the value at each data point... exceeds two percent at any point, use the best-fit non-linear equation which represents the data to within two percent of each test point to determine concentration. (d) Oxygen interference optimization. Prior...

40 CFR 90.316 - Hydrocarbon analyzer calibration.

Code of Federal Regulations, 2014 CFR

2014-07-01

... from a least-squares best-fit straight line is two percent or less of the value at each data point... exceeds two percent at any point, use the best-fit non-linear equation which represents the data to within two percent of each test point to determine concentration. (d) Oxygen interference optimization. Prior...

40 CFR 86.1324-84 - Carbon dioxide analyzer calibration.

Code of Federal Regulations, 2011 CFR

2011-07-01

... calibrated, if the deviation from a least-squares best-fit straight line is within ±2 percent or less of the... exceeds these limits, then the best-fit non-linear equation which represents the data within these limits shall be used to determine concentration values. (d) The initial and periodic interference, system check...

40 CFR 89.322 - Carbon dioxide analyzer calibration.

Code of Federal Regulations, 2013 CFR

2013-07-01

... engineering practice. For each range calibrated, if the deviation from a least-squares best-fit straight line... range. If the deviation exceeds these limits, the best-fit non-linear equation which represents the data... interference, system check, and calibration test procedures specified in 40 CFR part 1065 may be used in lieu...

40 CFR 91.316 - Hydrocarbon analyzer calibration.

Code of Federal Regulations, 2012 CFR

2012-07-01

... deviation from a least-squares best-fit straight line is two percent or less of the value at each data point... exceeds two percent at any point, use the best-fit non-linear equation which represents the data to within two percent of each test point to determine concentration. (d) Oxygen interference optimization...

40 CFR 90.318 - Oxides of nitrogen analyzer calibration.

Code of Federal Regulations, 2012 CFR

2012-07-01

... chemiluminescent oxides of nitrogen analyzer as described in this section. (b) Initial and Periodic Interference...-squares best-fit straight line is two percent or less of the value at each data point, calculate... at any point, use the best-fit non-linear equation which represents the data to within two percent of...

40 CFR 91.318 - Oxides of nitrogen analyzer calibration.

Code of Federal Regulations, 2012 CFR

2012-07-01

... nitrogen analyzer as described in this section. (b) Initial and periodic interference. Prior to its...-squares best-fit straight line is two percent or less of the value at each data point, concentration... two percent at any point, use the best-fit non-linear equation which represents the data to within two...

40 CFR 90.318 - Oxides of nitrogen analyzer calibration.

Code of Federal Regulations, 2014 CFR

2014-07-01

... chemiluminescent oxides of nitrogen analyzer as described in this section. (b) Initial and Periodic Interference...-squares best-fit straight line is two percent or less of the value at each data point, calculate... at any point, use the best-fit non-linear equation which represents the data to within two percent of...

40 CFR 91.318 - Oxides of nitrogen analyzer calibration.

Code of Federal Regulations, 2014 CFR

2014-07-01

... nitrogen analyzer as described in this section. (b) Initial and periodic interference. Prior to its...-squares best-fit straight line is two percent or less of the value at each data point, concentration... two percent at any point, use the best-fit non-linear equation which represents the data to within two...

40 CFR 86.1323-84 - Oxides of nitrogen analyzer calibration.

Code of Federal Regulations, 2012 CFR

2012-07-01

... calibrated, if the deviation from a least-squares best-fit straight line is within ±2 percent of the value at... exceeds these limits, then the best-fit non-linear equation which represents the data within these limits shall be used to determine concentration values. (c) The initial and periodic interference, system check...

40 CFR 86.1323-84 - Oxides of nitrogen analyzer calibration.

Code of Federal Regulations, 2013 CFR

2013-07-01

... calibrated, if the deviation from a least-squares best-fit straight line is within ±2 percent of the value at... exceeds these limits, then the best-fit non-linear equation which represents the data within these limits shall be used to determine concentration values. (c) The initial and periodic interference, system check...

40 CFR 89.322 - Carbon dioxide analyzer calibration.

Code of Federal Regulations, 2014 CFR

2014-07-01

... engineering practice. For each range calibrated, if the deviation from a least-squares best-fit straight line... range. If the deviation exceeds these limits, the best-fit non-linear equation which represents the data... interference, system check, and calibration test procedures specified in 40 CFR part 1065 may be used in lieu...

40 CFR 91.316 - Hydrocarbon analyzer calibration.

Code of Federal Regulations, 2013 CFR

2013-07-01

... deviation from a least-squares best-fit straight line is two percent or less of the value at each data point... exceeds two percent at any point, use the best-fit non-linear equation which represents the data to within two percent of each test point to determine concentration. (d) Oxygen interference optimization...

40 CFR 89.322 - Carbon dioxide analyzer calibration.

Code of Federal Regulations, 2012 CFR

2012-07-01

... engineering practice. For each range calibrated, if the deviation from a least-squares best-fit straight line... range. If the deviation exceeds these limits, the best-fit non-linear equation which represents the data... interference, system check, and calibration test procedures specified in 40 CFR part 1065 may be used in lieu...

[Analysis of different forms Linderae Radix based on HPLC and NIRS fingerprints].

PubMed

Du, Wei-Feng; Yue, Xian-Ke; Wu, Yao; Ge, Wei-Hong; Lu, Tu-Lin; Wang, Zhi-Min

2016-10-01

Three different forms of Linderae Radix were evaluated by HPLC combined with NIRS fingerprint. The Linderae Radix was divided into three forms, including spindle root, straight root and old root. The HPLC fingerprints were developed, and then cluster analysis was performed using the SPSS software. The near-infrared spectra of Linderae Radix was collected, and then established the discriminant analysis model. The similarity values of the spindle root and straight root all were above 0.990, while the similarity value of the old root was less than 0.850. Two forms of Linderae Radix were obviously divided into three parts by the NIRS model and Cluster analysis. The results of HPLC and FT-NIR analysis showed the quality of Linderae Radix old root was different from the spindle root and straight root. The combined use of the two methods could identify different forms of Linderae Radix quickly and accurately. Copyright© by the Chinese Pharmaceutical Association.

Method of measuring cross-flow vortices by use of an array of hot-film sensors

NASA Technical Reports Server (NTRS)

Agarwal, Aval K. (Inventor); Maddalon, Dal V. (Inventor); Mangalam, Siva M. (Inventor)

1993-01-01

The invention is a method for measuring the wavelength of cross-flow vortices of air flow having streamlines of flow traveling across a swept airfoil. The method comprises providing a plurality of hot-film sensors. Each hot-film sensor provides a signal which can be processed, and each hot-film sensor is spaced in a straight-line array such that the distance between successive hot-film sensors is less than the wavelength of the cross-flow vortices being measured. The method further comprises determining the direction of travel of the streamlines across the airfoil and positioning the straight-line array of hot film sensors perpendicular to the direction of travel of the streamlines, such that each sensor has a spanwise location. The method further comprises processing the signals provided by the sensors to provide root-mean-square values for each signal, plotting each root-mean-square value as a function of its spanwise location, and determining the wavelength of the cross-flow vortices by noting the distance between two maxima or two minima of root-mean-square values.

Quantifying and Reducing Curve-Fitting Uncertainty in Isc

DOE Office of Scientific and Technical Information (OSTI.GOV)

Campanelli, Mark; Duck, Benjamin; Emery, Keith

2015-06-14

Current-voltage (I-V) curve measurements of photovoltaic (PV) devices are used to determine performance parameters and to establish traceable calibration chains. Measurement standards specify localized curve fitting methods, e.g., straight-line interpolation/extrapolation of the I-V curve points near short-circuit current, Isc. By considering such fits as statistical linear regressions, uncertainties in the performance parameters are readily quantified. However, the legitimacy of such a computed uncertainty requires that the model be a valid (local) representation of the I-V curve and that the noise be sufficiently well characterized. Using more data points often has the advantage of lowering the uncertainty. However, more data pointsmore » can make the uncertainty in the fit arbitrarily small, and this fit uncertainty misses the dominant residual uncertainty due to so-called model discrepancy. Using objective Bayesian linear regression for straight-line fits for Isc, we investigate an evidence-based method to automatically choose data windows of I-V points with reduced model discrepancy. We also investigate noise effects. Uncertainties, aligned with the Guide to the Expression of Uncertainty in Measurement (GUM), are quantified throughout.« less

Short-term influence of tank tracks on vegetation and microphytic crusts in shrubsteppe habitat

USGS Publications Warehouse

Watts, Stephen E.

1998-01-01

Artemisia tridentata Nutt.) habitat within the Idaho Army National Guard Orchard Training Area in southwestern Idaho. The purpose of this study was to determine the short-term (1a??2 years) influence of tank tracks on vegetation and microphytic crusts in shrubsteppe habitat. The two types of tank tracks studied were divots (area where one track has been stopped or slowed to make a sharp turn) and straight-line tracks. Divots generally had a stronger influence on vegetation and microphytic crusts than did straight-line tracks. Tank tracks increased cover of bare ground, litter, and exotic annuals, and reduced cover of vegetation, perennial native grasses, sagebrush, and microphytic crusts. Increased bare ground and reduced cover of vegetation and microphytic crusts caused by tank tracks increase the potential for soil erosion and may reduce ecosystem productivity. Reduced sagebrush cover caused by tank tracks may reduce habitat quality for rodents. Tank tracks may also facilitate the invasion of exotic annuals into sagebrush habitat, increasing the potential for wildfire and subsequent habitat degradation. Thus, creation of divots and movement through sagebrush habitat by tanks should be minimized.

Investigation of the effect of a bend in a transfer line that separates a pulse tube cold head and a pressure wave generator

NASA Astrophysics Data System (ADS)

Dev, A. A.; Atrey, M. D.; Vanapalli, S.

2017-02-01

A transfer line between a pulse tube cold head and a pressure wave generator is usually required to isolate the cold head from the vibrations of the compressor. Although it is a common practice to use a thin and narrow straight tube, a bent tube would allow design flexibility and easy mounting of the cold head, such as in a split Stirling type pulse tube cryocooler. In this paper, we report a preliminary investigation on the effect of the bending of the tube on the flow transfer characteristics. A numerical study using commercial computational fluid dynamics model is performed to gain insight into the flow characteristics in the bent tube. Oscillating flow experiments are performed with a straight and a bent tube at a filling pressure of 15 bar and an operating frequency of 40, 50 and 60 Hz. The data and the corresponding numerical simulations point to the hypothesis that the secondary flow in the bent tube causes a decrease in flow at a fixed pressure amplitude.

Quantifying and Reducing Curve-Fitting Uncertainty in Isc: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Campanelli, Mark; Duck, Benjamin; Emery, Keith

Current-voltage (I-V) curve measurements of photovoltaic (PV) devices are used to determine performance parameters and to establish traceable calibration chains. Measurement standards specify localized curve fitting methods, e.g., straight-line interpolation/extrapolation of the I-V curve points near short-circuit current, Isc. By considering such fits as statistical linear regressions, uncertainties in the performance parameters are readily quantified. However, the legitimacy of such a computed uncertainty requires that the model be a valid (local) representation of the I-V curve and that the noise be sufficiently well characterized. Using more data points often has the advantage of lowering the uncertainty. However, more data pointsmore » can make the uncertainty in the fit arbitrarily small, and this fit uncertainty misses the dominant residual uncertainty due to so-called model discrepancy. Using objective Bayesian linear regression for straight-line fits for Isc, we investigate an evidence-based method to automatically choose data windows of I-V points with reduced model discrepancy. We also investigate noise effects. Uncertainties, aligned with the Guide to the Expression of Uncertainty in Measurement (GUM), are quantified throughout.« less

A power function profile of a ski jumping in-run hill.

PubMed

Zanevskyy, Ihor

2011-01-01

The aim of the research was to find a function of the curvilinear segment profile which could make possible to avoid an instantaneous increasing of a curvature and to replace a circle arc segment on the in-run of a ski jump without any correction of the angles of inclination and the length of the straight-line segments. The methods of analytical geometry and trigonometry were used to calculate an optimal in-run hill profile. There were two fundamental conditions of the model: smooth borders between a curvilinear segment and straight-line segments of an in-run hill and concave of the curvilinear segment. Within the framework of this model, the problem has been solved with a reasonable precision. Four functions of a curvilinear segment profile of the in-run hill were investigated: circle arc, inclined quadratic parabola, inclined cubic parabola, and power function. The application of a power function to the in-run profile satisfies equal conditions for replacing a circle arc segment. Geometrical parameters of 38 modern ski jumps were investigated using the methods proposed.

Measuring geographical accessibility to palliative and end of life (PEoLC) related facilities: a comparative study in an area with well-developed specialist palliative care (SPC) provision.

PubMed

Pearson, Clare; Verne, Julia; Wells, Claudia; Polato, Giovanna M; Higginson, Irene J; Gao, Wei

2017-01-26

Geographical accessibility is important in accessing healthcare services. Measuring it has evolved alongside technological and data analysis advances. High correlations between different methods have been detected, but no comparisons exist in the context of palliative and end of life care (PEoLC) studies. To assess how geographical accessibility can affect PEoLC, selection of an appropriate method to capture it is crucial. We therefore aimed to compare methods of measuring geographical accessibility of decedents to PEoLC-related facilities in South London, an area with well-developed SPC provision. Individual-level death registration data in 2012 (n = 18,165), from the Office for National Statistics (ONS) were linked to area-level PEoLC-related facilities from various sources. Simple and more complex measures of geographical accessibility were calculated using the residential postcodes of the decedents and postcodes of the nearest hospital, care home and hospice. Distance measures (straight-line, travel network) and travel times along the road network were compared using geographic information system (GIS) mapping and correlation analysis (Spearman rho). Borough-level maps demonstrate similarities in geographical accessibility measures. Strong positive correlation exist between straight-line and travel distances to the nearest hospital (rho = 0.97), care home (rho = 0.94) and hospice (rho = 0.99). Travel times were also highly correlated with distance measures to the nearest hospital (rho range = 0.84-0.88), care home (rho = 0.88-0.95) and hospice (rho = 0.93-0.95). All correlations were significant at p < 0.001 level. Distance-based and travel-time measures of geographical accessibility to PEoLC-related facilities in South London are similar, suggesting the choice of measure can be based on the ease of calculation.

New well testing applications of the pressure derivative

DOE Office of Scientific and Technical Information (OSTI.GOV)

Onur, M.

1989-01-01

This work presents new derivative type curves based on a new derivative group which is equal to the dimensionless pressure group divided by its logarithmic derivative with respect to dimensionless time group. One major advantage of these type curves is that the type-curve match of field pressure/pressure-derivative data with the new derivative type curves is accomplished by moving the field data plot in only the horizontal direction. This type-curve match fixes time match-point values. The pressure change versus time data is then matched with the dimensionless pressure solution to determine match-point values. Well/reservoir parameters can then be estimated in themore » standard way. This two step type-curve matching procedure increases the likelihood of obtaining a unique match. Moreover, the unique correspondence between the ordinate of the field data plot and the new derivative type curves should prove useful in determining whether given field data actually represents the well/reservoir model assumed by a selected type curve solution. It is also shown that the basic idea used in construction the type curves can be used to ensure that proper semilog straight lines are chosen when analyzing pressure data by semilog methods. Analysis of both drawdown and buildup data is considered and actual field cases are analyzed using the new derivative type curves and the semilog identification method. This work also presents new methods based on the pressure derivative to analyze buildup data obtained at a well (fracture or unfractured) produced to pseudosteady-state prior to shut-in. By using a method of analysis based on the pressure derivative, it is shown that a well's drainage area at the instant of shut-in and the flow capacity can be computed directly from buildup data even in cases where conventional semilog straight lines are not well-defined.« less

Physiological and technical commitment during a 300-m in-line skating trial in athletes of different age categories.

PubMed

Invernizzi, Pietro L; Scurati, Raffaele; Crotti, Matteo; Bosio, Andrea; Longo, Stefano; Esposito, Fabio

2018-01-04

This study investigated the differences in strength, technique and time performance in in-line skaters of three age categories during a 300 m trial. Possible correlations among these variables were also assessed. Thirty-six elite in-line skaters (Cadets, Juniors and Seniors, n=12 each; 14±1, 16±1, and 24±6 years of age, respectively) performed a 300-m trial on an outdoor oval track. Total time (Ttot), 100-m fractions and duration of each skating technique (initial acceleration phase, straight push and cross-over) were recorded. A squat jump (SJ) was performed before and after the trial. Heart rate, blood lactate concentration ([La-]) and rate of perceived exertion (RPE) were collected before, during and at the end of the trial. Ttot was longer and SJ lower in Cadets compared to the other groups. Seniors employed the cross-over technique for a longer period than the straight push technique, compared to Juniors and Cadets. Ttot correlated negatively with SJ in Seniors. The number of significant correlations between skating techniques' duration and both Ttot and SJ increased with age category. No differences among groups were found for heart rate, [La-] and RPE. With increasing age category, leg strength appeared to be the more related aspect to skating performance. To improve 300-m in-line skating performance, trainers should pay particular attention to the enhancement of leg strength and cross-over skating technique.

Effect of Vacuum on Venous Drainage: an Experimental Evaluation on Pediatric Venous Cannulas and Tubing Systems.

PubMed

Vida, V L; Bhattarai, A; Speggiorin, S; Zanella, F; Stellin, G

2014-01-01

To observe how vacuum assisted venous drainage (VAVD) may influence the flow in a cardiopulmonary bypass circuit with different size of venous lines and cannulas. The experimental circuit was assembled to represent the cardiopulmonary bypass circuit routinely used during cardiac surgery. Wall suction was applied directly, modulated and measured into the venous reservoir. The blood flow was measured with a flow-meter positioned on the venous line. The circuit prime volume was replaced with group O date expired re-suspended red cells and Plasmalyte 148 to a hematocrit of 28% to 30%. In an open circuit with gravity siphon venous drain, angled cannulae drain more than straight ones regardless the amount of suction applied to the venous line (16 Fr straight cannula (S) drains 90 ml/min less than a 16 Fr angled (A) with a siphon gravity). The same flow can be obtained with lower cannula size and higher suction (i.e. 12 A with and -30 mmHg). Tables have been created to list how the flow varies according to the size of the cannulas, the size of the venous tubes, and the amount of suction applied to the system. Vacuum assisted venous drainage allows the use of smaller cannulae and venous lines to maintain a good venous return, which is very useful during minimally invasive approaches. The present study should be considered as a preliminary attempt to create a scientific-based starting point for a uniform the use of VAVD.

The role of physical content in piagetian spatial tasks: Sex differences in spatial knowledge?

NASA Astrophysics Data System (ADS)

Golbeck, Susan L.

Sex-related differences on Piagetian horizontality (water level) and verticality (plumb line) tasks were examined in 64 college students. It was hypothesized that females' difficulties on these Euclidean spatial problems are due not to differences in underlying spatial competence, but rather to differences in knowledge of task specific information about the physical properties of water levels and plumb lines. This was tested by presenting subjects with the standard water level and plumb line problems and also modified problems not requiring knowledge of physical principles (i.e., drawing straight up and down or straight across lines inside tipped rectangles). While males were expected to outperform females on the standard tasks, no sex differences were expected on the modified tasks. Results of an ANOVA on scores for horizontality and verticality each showed main effects for sex and task version but failed to reveal the hypothesized interaction. However, performance on the Euclidean spatial tasks was also considered in terms of overall success versus failure. While males were more successful than females in the standard format, males and females were equally successful in the modified, nonphysical, format. Hence, college aged males and females generally do not differ in spatial competence although they may be differentially influenced by task content. Findings are discussed in terms of their implications for theory and practice. It is emphasized that science educators must be especially aware of such task influences for females so that performance deficits are not mistaken for competence deficits.

Application of Lorenz curve to interpret concentration of contraception and fertility in a population.

PubMed

Ghanma, M A; Rider, R V; Sirageldin, I

1984-01-01

The Lorenz Curve, originally developed to measure the concentration of wealth in a population, was used to describe the distribution of contraceptive practice in Jordan. Data from the 1976 Jordan Fertility Study, carried out as part of the World Fertility Survey program, was used in the analysis. The application of the Automatic Interaction Detector program to the survey's sample population of 3611 women of reproductive age divided the sample into 6 mutually exclusive groups on the basis of residence, education, and whether desired family size was attained or not attained. These 3 characteristics accounted for a major portion of the variation in contraceptive practice. These subgroups, in ascending order by the proportion practicing contraception, were: 1) rural women with unattained desired family size; 2) urban, illiterate women with unattained desired family size; 3) rural women with attained desired family size; 4) urban, literate women with unattained desired family size; 5) urban, illiterate women with attained desired family size; and 6) urban, literate women with attained desired family size. The cumulative proportion of the sample in each ordered subdivision was plotted on the X axis of a graph, and the cumulative proportion of those practicing contraception was plotted on the Y axis of the graph. A line connecting the intersection of the points on the X and Y axis was then drawn. The resultant line was a concave ascending line. If contraceptive practice was evenly distributed in the population, the line would be a straight diagonal line. The plotted curved line indicated that contraceptive practice was unevenly distributed in the population. 2 indexes for measuring the area between the diagonal and the line resulting from plotting the observed distribution for each subgroup was used to assess the degree of concentration of contraceptive practice in the population. The indexes also indicated that contraceptive practice was unequally distributed. When separate curves were plotted for the subgroups with attained desired family size and the subgroups without attained desired family size, it was apparent that the distribution of contraceptive practice was more uniform among those with attained desired family size than among the other 3 subgroups. A curve for the distribution of births was then plotted on the same graph. This curve was not a true application of the Lorenz Curve since it was based on the order of the subdivisions by birth rates. The resultant line approached the straight diagonal line and indicated that the distribution of births was fairly evenly distributed in the population. The uneven distribution of contraceptive practice and the uniform distribution of births suggests that contraceptive practice in this population is ineffective. This may be a characteristic of populations in the early stages of fertility control.

The Universal Transverse Mercator (UTM) grid

USGS Publications Warehouse

,

1997-01-01

The most convenient way to identify points on the curved surface of the Earth is with a system of reference lines called parallels of latitude and meridians of longitude. On some maps the meridians and parallels appear as straight lines. On most modern maps, however, the meridians and parallels may appear as curved lines. These differences are due to the mathematical treatment required to portray a curved surface on a flat surface so that important properties of the map (such as distance and areal accuracy) are shown with minimum distortion. The system used to portray a portion of the round Earth on a flat surface is called a map projection.

The Universal Transverse Mercator (UTM) grid

USGS Publications Warehouse

,

1999-01-01

The most convenient way to identify points on the curved surface of the Earth is with a system of reference lines called parallels of latitude and meridians of longitude. On some maps, the meridians and parallels appear as straight lines. On most modern maps, however, the meridians and parallels appear as curved lines. These differences sre due to the mathematical treatment required to portray a curved surface on a flat surface so that important properties of the map (such as distance and areal accuracy) are shown with minimum distortion. The system used to portray a portion of the round Earth on a flat surface is called a map projection.

Finger Vein Recognition Using Local Line Binary Pattern

PubMed Central

Rosdi, Bakhtiar Affendi; Shing, Chai Wuh; Suandi, Shahrel Azmin

2011-01-01

In this paper, a personal verification method using finger vein is presented. Finger vein can be considered more secured compared to other hands based biometric traits such as fingerprint and palm print because the features are inside the human body. In the proposed method, a new texture descriptor called local line binary pattern (LLBP) is utilized as feature extraction technique. The neighbourhood shape in LLBP is a straight line, unlike in local binary pattern (LBP) which is a square shape. Experimental results show that the proposed method using LLBP has better performance than the previous methods using LBP and local derivative pattern (LDP). PMID:22247670

Phonon Conduction in Silicon Nanobeam Labyrinths

DOE PAGES

Park, Woosung; Romano, Giuseppe; Ahn, Ethan C.; ...

2017-07-24

Here we study single-crystalline silicon nanobeams having 470 nm width and 80 nm thickness cross section, where we produce tortuous thermal paths (i.e. labyrinths) by introducing slits to control the impact of the unobstructed “line-of-sight” (LOS) between the heat source and heat sink. The labyrinths range from straight nanobeams with a complete LOS along the entire length to nanobeams in which the LOS ranges from partially to entirely blocked by introducing slits, s = 95, 195, 245, 295 and 395 nm. The measured thermal conductivity of the samples decreases monotonically from ~47 W m -1K -1 for straight beam tomore » ~31 W m -1 K -1 for slit width of 395 nm. A model prediction through a combination of the Boltzmann transport equation and ab initio calculations shows an excellent agreement with the experimental data to within ~8%. The model prediction for the most tortuous path (s = 395 nm) is reduced by ~14% compared to a straight beam of equivalent cross section. This study suggests that LOS is an important metric for characterizing and interpreting phonon propagation in nanostructures.« less

Tomography and the Herglotz-Wiechert inverse formulation

NASA Astrophysics Data System (ADS)

Nowack, Robert L.

1990-04-01

In this paper, linearized tomography and the Herglotz-Wiechert inverse formulation are compared. Tomographic inversions for 2-D or 3-D velocity structure use line integrals along rays and can be written in terms of Radon transforms. For radially concentric structures, Radon transforms are shown to reduce to Abel transforms. Therefore, for straight ray paths, the Abel transform of travel-time is a tomographic algorithm specialized to a one-dimensional radially concentric medium. The Herglotz-Wiechert formulation uses seismic travel-time data to invert for one-dimensional earth structure and is derived using exact ray trajectories by applying an Abel transform. This is of historical interest since it would imply that a specialized tomographic-like algorithm has been used in seismology since the early part of the century (see Herglotz, 1907; Wiechert, 1910). Numerical examples are performed comparing the Herglotz-Wiechert algorithm and linearized tomography along straight rays. Since the Herglotz-Wiechert algorithm is applicable under specific conditions, (the absence of low velocity zones) to non-straight ray paths, the association with tomography may prove to be useful in assessing the uniqueness of tomographic results generalized to curved ray geometries.

BEAM TRANSPORT LINES FOR THE BSNS.

DOE Office of Scientific and Technical Information (OSTI.GOV)

WEI, J.

2006-06-26

This paper presents the design of two beam transport lines at the BSNS: one is the injection line from the Linac to the RCS and the other is the target line from the RCS to the target station. In the injection beam line, space charge effects, transverse halo collimation, momentum tail collimation and debunching are the main concerned topics. A new method of using triplet cells and stripping foils is used to collimate transverse halo. A long straight section is reserved for the future upgrading linac and debuncher. In the target beam line, large halo emittance, beam stability at themore » target due to kicker failures and beam jitters, shielding of back-scattering neutrons from the target are main concerned topics. Special bi-gap magnets will be used to reduce beam losses in the collimators in front of the target.« less

Selecting maxillary anterior tooth width by measuring certain facial dimensions in the Kurdish population.

PubMed

A L-Kaisy, Neda; Garib, Balkees Taha

2016-03-01

One of the most difficult aspects of complete denture fabrication is selecting appropriately sized maxillary anterior teeth that will harmonize with the face. There are no generally accepted or naturally observed principles to guide dentists in this selection. The purpose of this study was to determine whether a relationship exists between various facial measurements and the different single or combined mesiodistal widths of maxillary anterior teeth in a Kurdish population. A total of 65 Kurdish dental students participated in this study. Two standardized digital photographs of the face (relaxed and smiling capture) were recorded. The interpupillary distance (IPD), inner canthal distance (ICD), interalar distance (IAD), and width of the 2 central incisors were determined by Image J software. The mesiodistal width and the combined straight-line width of the centrals, laterals, and canines were measured directly from the casts of the participants with digital calipers. A simple linear regression and the Pearson correlation coefficient were used to investigate the relationship between the particular facial measurement and the widths of the anterior teeth (α=.05). Significant correlations existed between the IPD and different tooth measurements; the highest was with the mean width of the canines (r=0.55). The proposed proportion between the IPD and the central incisor width was 6.93. The golden proportion of the ICD to the width of the central incisors and of the IAD to the straight-line width of the 6 anterior teeth could be used as a dependent parameter in Kurdish men. The IPD can be used to predict the width of anterior teeth in both sexes. In men, the width of the central incisors may be estimated from the ICD and the straight-line width of the 6 anterior teeth from the IAD. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Movements of wolves at the northern extreme of the species' range, including during four months of darkness

USGS Publications Warehouse

Mech, L.D.; Cluff, H.D.

2011-01-01

Information about wolf (Canis lupus) movements anywhere near the northern extreme of the species' range in the High Arctic (<75??N latitude) are lacking. There, wolves prey primarily on muskoxen (Ovibos moschatus) and must survive 4 months of 24 hr/day winter darkness and temperatures reaching -53 C. The extent to which wolves remain active and prey on muskoxen during the dark period are unknown, for the closest area where information is available about winter wolf movements is >2,250 km south. We studied a pack of ???20 wolves on Ellesmere Island, Nunavut, Canada (80??N latitude) from July 2009 through mid-April 2010 by collaring a lead wolf with a Global Positioning System (GPS)/Argos radio collar. The collar recorded the wolf's precise locations at 6:00 a.m. and 6:00 p.m. daily and transmitted the locations by satellite to our email. Straight-line distances between consecutive 12-hr locations varied between 0 and 76 km. Mean (SE) linear distance between consecutive locations (n = 554) was 11 (0.5) km. Total minimum distance traveled was 5,979 km, and total area covered was 6,640 km2, the largest wolf range reported. The wolf and presumably his pack once made a 263-km (straight-line distance) foray to the southeast during 19-28 January 2010, returning 29 January to 1 February at an average of 41 km/day straight-line distances between 12-hr locations. This study produced the first detailed movement information about any large mammal in the High Arctic, and the average movements during the dark period did not differ from those afterwards. Wolf movements during the dark period in the highest latitudes match those of the other seasons and generally those of wolves in lower latitudes, and, at least with the gross movements measurable by our methods, the 4-month period without direct sunlight produced little change in movements. ?? 2011 Mech, Cluff.

Movements of wolves at the northern extreme of the species' range, including during four months of darkness

USGS Publications Warehouse

Mech, L. David; Cluff, H. Dean

2011-01-01

Information about wolf (Canis lupus) movements anywhere near the northern extreme of the species' range in the High Arctic (>75°N latitude) are lacking. There, wolves prey primarily on muskoxen (Ovibos moschatus) and must survive 4 months of 24 hr/day winter darkness and temperatures reaching -53 C. The extent to which wolves remain active and prey on muskoxen during the dark period are unknown, for the closest area where information is available about winter wolf movements is >2,250 km south. We studied a pack of ≥20 wolves on Ellesmere Island, Nunavut, Canada (80°N latitude) from July 2009 through mid-April 2010 by collaring a lead wolf with a Global Positioning System (GPS)/Argos radio collar. The collar recorded the wolf's precise locations at 6:00 a.m. and 6:00 p.m. daily and transmitted the locations by satellite to our email. Straight-line distances between consecutive 12-hr locations varied between 0 and 76 km. Mean (SE) linear distance between consecutive locations (n = 554) was 11 (0.5) km. Total minimum distance traveled was 5,979 km, and total area covered was 6,640 km2, the largest wolf range reported. The wolf and presumably his pack once made a 263-km (straight-line distance) foray to the southeast during 19–28 January 2010, returning 29 January to 1 February at an average of 41 km/day straight-line distances between 12-hr locations. This study produced the first detailed movement information about any large mammal in the High Arctic, and the average movements during the dark period did not differ from those afterwards. Wolf movements during the dark period in the highest latitudes match those of the other seasons and generally those of wolves in lower latitudes, and, at least with the gross movements measurable by our methods, the 4-month period without direct sunlight produced little change in movements.

Preanalytic Factors Associated With Hemolysis in Emergency Department Blood Samples.

PubMed

Phelan, Michael P; Reineks, Edmunds Z; Schold, Jesse D; Hustey, Frederic M; Chamberlin, Janelle; Procop, Gary W

2018-02-01

- Hemolysis of emergency department blood samples is a common occurrence and has a negative impact on health care delivery. - To determine the effect of preanalytic factors (straight stick, intravenous [IV] line, needle gauge, location of blood draw, syringe versus vacuum tube use, tourniquet time) on hemolysis in emergency department blood samples. - A single 65 000-visit emergency department's electronic health record was queried for emergency department potassium results and blood draw technique for all samples obtained in calendar year 2014, resulting in 54 531 potassium results. Hemolyzed potassium was measured by hemolysis index. Comparisons of hemolysis by sampling technique were conducted by χ 2 tests. - Overall hemolysis was 10.0% (5439 of 54 531). Hemolysis among samples obtained from straight stick was significantly less than among those obtained with IV line (5.4% [33 of 615] versus 10.2% [4821 of 47 266], P < .001). For IV-placed blood draws, antecubital location had a statistically significant lower overall hemolysis compared with other locations: 7.4% (2117 of 28 786) versus 14.6% (2622 of 17 960) ( P < .001). For blood drawn with a syringe compared with vacuum, hemolysis was 13.0% (92 of 705) and 11.0% (1820 of 16 590), respectively ( P = .09, not significant). For large-gauge IV blood draws versus smaller-gauge IV lines, a lower hemolysis was also observed (9.3% [3882 of 41 571] versus 16.7% [939 of 5633]) ( P < .001). For IV-drawn blood with tourniquet time less than 60 seconds, hemolysis was 10.3% (1362 of 13 162) versus 13.9% for more than 60 seconds (532 of 3832), P < .001. - This study confirmed previous findings that straight stick and antecubital location are significantly associated with reduced hemolysis and indicated that shorter tourniquet time and larger gauge for IV draws were significantly associated with lower hemolysis.

Effect of post-thaw incubation on sperm kinematics and acrosomal integrity of ram spermatozoa cryopreserved in medium-sized French straws.

PubMed

Bag, Sadhan; Joshi, Anil; Naqvi, S M K; Mittal, J P

2004-08-01

The objectives were to assess the effect of post-thaw in vitro incubation on motion characteristics and acrosomal integrity of ram spermatozoa of native Malpura and Bharat Merino breeds maintained under a semi-arid tropical environment. Good quality semen samples of both breeds were diluted, packaged in medium-sized straws, and frozen under controlled conditions. Straws were thawed at 60 degrees C for 10s and thawed samples were incubated at 37 degrees C for 4h. Post-thaw motion characteristics and acrosomal integrity of incubated spermatozoa were assessed (by computer-aided semen analysis and Giemsa staining, respectively) just prior to incubation and at hourly intervals thereafter. There was a significant effect of incubation time on motility characteristics and the proportion of spermatozoa with normal acrosomes; 81.4% (arcsin transformed value, 65.2) of spermatozoa were motile at the start of incubation, with 47.9% (arcsin transformed value, 44.4) motile after 4h. At the corresponding times, there were normal acrosomes in 65.8 (arcsin transformed value, 54.8) and 55.7% (arcsin transformed value, 48.9) of spermatozoa, respectively. The percentage straightness of spermatozoa varied during incubation (P < 0.01). However, there was no significant change in percentage linearity, curvilinear velocity, average path velocity, straight line velocity, lateral head displacement, and beat cross frequency of spermatozoa during incubation. There were no breed variations in any motility parameters during incubation, except percentage straightness (P < 0.05), lateral head displacement (P < 0.05) and beat cross frequency (P < 0.01). That sperm motility and acrosomal morphology were very acceptable immediately post-thaw and after 4h of incubation indicated the efficacy of cryopreserving ram spermatozoa under controlled conditions in medium-sized straws.

A Novel Stimulus Artifact Removal Technique for High-Rate Electrical Stimulation

PubMed Central

Heffer, Leon F; Fallon, James B

2008-01-01

Electrical stimulus artifact corrupting electrophysiological recordings often make the subsequent analysis of the underlying neural response difficult. This is particularly evident when investigating short-latency neural activity in response to high-rate electrical stimulation. We developed and evaluated an off-line technique for the removal of stimulus artifact from electrophysiological recordings. Pulsatile electrical stimulation was presented at rates of up to 5000 pulses/s during extracellular recordings of guinea pig auditory nerve fibers. Stimulus artifact was removed by replacing the sample points at each stimulus artifact event with values interpolated along a straight line, computed from neighbouring sample points. This technique required only that artifact events be identifiable and that the artifact duration remained less than both the inter-stimulus interval and the time course of the action potential. We have demonstrated that this computationally efficient sample-and-interpolate technique removes the stimulus artifact with minimal distortion of the action potential waveform. We suggest that this technique may have potential applications in a range of electrophysiological recording systems. PMID:18339428

Shear wave speed and dispersion measurements using crawling wave chirps.

PubMed

Hah, Zaegyoo; Partin, Alexander; Parker, Kevin J

2014-10-01

This article demonstrates the measurement of shear wave speed and shear speed dispersion of biomaterials using a chirp signal that launches waves over a range of frequencies. A biomaterial is vibrated by two vibration sources that generate shear waves inside the medium, which is scanned by an ultrasound imaging system. Doppler processing of the acquired signal produces an image of the square of vibration amplitude that shows repetitive constructive and destructive interference patterns called "crawling waves." With a chirp vibration signal, successive Doppler frames are generated from different source frequencies. Collected frames generate a distinctive pattern which is used to calculate the shear speed and shear speed dispersion. A special reciprocal chirp is designed such that the equi-phase lines of a motion slice image are straight lines. Detailed analysis is provided to generate a closed-form solution for calculating the shear wave speed and the dispersion. Also several phantoms and an ex vivo human liver sample are scanned and the estimation results are presented. © The Author(s) 2014.

Residual stresses and plastic deformation in GTA-welded steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brand, P.C.; Keijser, T.H. de; Ouden, G. den

1993-03-01

Residual stresses and plastic deformation in single pass GTA welded low-carbon steel were studied by means of x-ray diffraction in combination with optical microscopy and hardness measurements. The residual stresses and the amount of plastic deformation (microstrain) were obtained from x-ray diffraction line positions and line broading. Since the plates were polished before welding, it was possible to observe in the optical microscope two types of Lueders bands. During heating curved Lueders bands and during cooling straight Lueders bands perpendicular to the weld are formed. The curved Lueders bands extend over a larger distance from the weld than the straightmore » Lueders bands. The amount of plastic deformation as obtained from the x-ray diffraction analysis is in agreement with these observations. An explanation is offered for the stresses measured in combination with plastic deformations observed. It is concluded that in the present experiments plastic deformation is the main cause of the residual stresses.« less

Comparison of beam position calculation methods for application in digital acquisition systems

NASA Astrophysics Data System (ADS)

Reiter, A.; Singh, R.

2018-05-01

Different approaches to the data analysis of beam position monitors in hadron accelerators are compared adopting the perspective of an analog-to-digital converter in a sampling acquisition system. Special emphasis is given to position uncertainty and robustness against bias and interference that may be encountered in an accelerator environment. In a time-domain analysis of data in the presence of statistical noise, the position calculation based on the difference-over-sum method with algorithms like signal integral or power can be interpreted as a least-squares analysis of a corresponding fit function. This link to the least-squares method is exploited in the evaluation of analysis properties and in the calculation of position uncertainty. In an analytical model and experimental evaluations the positions derived from a straight line fit or equivalently the standard deviation are found to be the most robust and to offer the least variance. The measured position uncertainty is consistent with the model prediction in our experiment, and the results of tune measurements improve significantly.

Effects of diluting medium and holding time on sperm motility analysis by CASA in ram.

PubMed

Mostafapor, Somayeh; Farrokhi Ardebili, Farhad

2014-01-01

The aim of this study was to evaluate the effects of dilution rate and holding time on various motility parameters using computer-assisted sperm analysis (CASA). The semen samples were collected from three Ghezel rams. Samples were diluted in seminal plasma (SP), phosphate-buffered saline (PBS) containing 1% bovine serum albumin (BSA) and Bioexcell. The motility parameters that computed and recorded by CASA include curvilinear velocity (VCL), straight line velocity (VSL), average path velocity (VAP), straightness (STR), linearity (LIN), amplitude of lateral head displacement (ALH), and beat cross frequency (BCF). In all diluters, there was a decrease in the average of all three parameters of sperms movement velocity as the time passed, but density of this decrease was more intensive in SP. The average of ALH between diluters indicated a significant difference, as it was more in Bioexcell in comparison with the similar amount in SP and PBS. The average of LIN in the diluted sperms in Bioexcell was less than two other diluters in all three times. The motility parameters of the diluted sperms in Bioexcell and PBS indicated an important and considerable difference with the diluted sperms in SP. According to the gained results, the Bioexcell has greater ability in preserving motility of sperm in comparison with the other diluters but as SP is considered as physiological environment for sperm. It seems that the evaluation of the motility parameters in Bioexcell and PBS cannot be an accurate and comparable evaluation with SP.

Centaur feedline dynamics study using power spectral methods. [fundamental mode resonant frequencies of RL-10 oxygen and hydrogen feed lines

NASA Technical Reports Server (NTRS)

Lorenzo, C. F.

1974-01-01

Tests were conducted to determine the dynamic characteristics of the Centaur/RL-10 oxygen and hydrogen feedlines. The fundamental-mode resonant frequencies were determined by applying power spectral methods to noise-generated data from hot firings of the RL-10 engine. The effect of net positive suction pressure of the main feed pumps on resonant frequency characteristics was determined to be a straight-line relation. Power spectral methods were also used to determine the dynamic characteristics of the boost pumps.

On the wrong inference of long-range correlations in climate data; the case of the solar and volcanic forcing over the Tropical Pacific

NASA Astrophysics Data System (ADS)

Varotsos, Costas A.; Efstathiou, Maria N.

2017-05-01

A substantial weakness of several climate studies on long-range dependence is the conclusion of long-term memory of the climate conditions, without considering it necessary to establish the power-law scaling and to reject a simple exponential decay of the autocorrelation function. We herewith show one paradigmatic case, where a strong long-range dependence could be wrongly inferred from incomplete data analysis. We firstly apply the DFA method on the solar and volcanic forcing time series over the tropical Pacific, during the past 1000 years and the results obtained show that a statistically significant straight line fit to the fluctuation function in a log-log representation is revealed with slope higher than 0.5, which wrongly may be assumed as an indication of persistent long-range correlations in the time series. We argue that the long-range dependence cannot be concluded just from this straight line fit, but it requires the fulfilment of the two additional prerequisites i.e. reject the exponential decay of the autocorrelation function and establish the power-law scaling. In fact, the investigation of the validity of these prerequisites showed that the DFA exponent higher than 0.5 does not justify the existence of persistent long-range correlations in the temporal evolution of the solar and volcanic forcing during last millennium. In other words, we show that empirical analyses, based on these two prerequisites must not be considered as panacea for a direct proof of scaling, but only as evidence that the scaling hypothesis is plausible. We also discuss the scaling behaviour of solar and volcanic forcing data based on the Haar tool, which recently proved its ability to reliably detect the existence of the scaling effect in climate series.

Dynamics of a homogeneous ball on a horizontal plane with sliding, spinning, and rolling friction taken into account

NASA Astrophysics Data System (ADS)

Ishkhanyan, M. V.; Karapetyan, A. V.

2010-04-01

We analyze the dynamics of a homogeneous ball on a horizontal plane with friction of all kinds, namely, sliding, spinning, and rolling friction, taken into account. The qualitative-analytic study of the ball dynamics is supplemented with numerical experiments. The problem on the motion of a homogeneous ball on a horizontal plane with friction was apparently first studied in 1758 by I. Euler (Leonard Euler's son) with sliding friction taken into account in the framework of the Coulomb model. I. Euler showed that the ball sliding ceases in finite time, after which the ball uniformly rolls along a fixed straight line and uniformly spins about the vertical. This result has long become classical and is described in many textbooks on theoretical mechanics. In 1998, V. F. Zhuravlev considered the problem of motion of a homogeneous ball on a horizontal plane with sliding and spinning friction taken into account in the framework of the Contensou-Zhuravlev model [1, 2] and showed that the ball sliding and spinning cease simultaneously, after which the ball uniformly rolls along a fixed straight line. The Contensou-Zhuravlev theory was further developed in [3-7]. In the present paper, we consider themotion of a homogeneous ball on a horizontal plane with friction of all kinds taken into account in the framework of the model proposed in [8]. We show that, in one and the same time, both the sliding velocity and the angular velocity of the ball become zero. Our studies are based on the results obtained in [2], the properties of the friction model proposed in [8], and the method for qualitative analysis of dynamics of dissipative systems [9, 10]. The qualitative-analytic study is supplemented with numerical experiments.

1DVAR Analysis of Temperature and Humidity Using GPS Radio Occultation Data

NASA Technical Reports Server (NTRS)

Poli, Paul; Joiner, Joanna; Kursinski, Robert

2000-01-01

The Global Positioning System enables positioning in 3 dimensions about our planet. It has been operational since 1994. Twenty-four satellites are used to aclile\\,e this performance. The signals sent by these satellites are electromagnetic waves travelling through our atmosphere down to the small receivers used by the civilian community and the military. Because of varying meteorological conditions (namely, temperature and humidity changes along the ray path), the rays do not travel in a straight line. They bend towards the surface. As a consequence, the ray path between two points is longer than a straight line, and the time it takes for a signal to travel this distance is longer. In 1995, a small GPS receiver was launched on a satellite (GPS/MET). It become possible to perform radio occultations around the Earth: the source - one of the 24 GPS satellites - is seen by the receiver as it rises or sets around the other side of the Earth. When the source disappears, the receiver progressively loses the signals. By measuring accurately the time delay between the emission and the reception of the signal, it is possible to infer which part of the delay is due to the atmosphere. We use GPS/MET data to retrieve temperature and humidity profiles simultaneously. A specific method is implemented: it combines information from numerical forecasts and GPS observations in an optimal way. Comparing the result with an independent source of observations (weather balloons), we demonstrate that GPS data have the potential to improve weather analyses. We also show that improved temperature and humidity profiles can be obtained using information from a forecast model. This confirms results obtained in this study using simulated data.

The Efficacy of FlexMaster's IntroFile, PreRaCe and Gates Glidden Drills in Straight-Line Access: A CBCT Assessment.

PubMed

Farhad Mollashahi, Narges; Sohrabi, Mahdi; Farhad Mollashahi, Leila; Mehdizadeh, Mojdeh

2014-01-01

An overlooked but important part of successful root canal treatment is a straight-line access (SLA). The purpose of this in vitro study was to compare the efficacy of IntroFile and PreRaCe rotary instruments with Gates Glidden (GG) drills in gaining SLA by cone-beam computed tomography (CBCT). A total of forty five extracted mandibular first molars were selected and mounted in dental like arches. Subsequently, they were randomly classified into three groups (n=15). After preparation of a standard access cavity, orifices of the mesiobuccal canal was reached and a #10 file was inserted to explore the canals until the file tip was visible at the apex. Then, preoperative CBCT images were taken. SLA was gained in three groups; group 1, FlexMaster's IntroFile (FM); group 2, PreRaCe (RC) and group 3, GG. Again, the first binding file at the working length (WL) was placed in the canal and postoperative CBCT images in similar positions were taken. The pre/post operative morphology of the canal was evaluated for changes. Data was analyzed using the one-way ANOVA and post-hoc Bonferroni analysis. The average amount of reduction in coronal canal curvature in FM, RC and GG groups was 2.43±1.79, 3.17±2.05 and 8.7±3.45, respectively. This descending trend was statistically significant. The difference between pre/post SLA changes in FM and RC groups was significant compared to GG group, while there were no significant differences between RC and FM. GG drills produced extraordinary results in reducing coronal curvature of the canal and achieving SLA. They are also more effective than nickel-titanium (NiTi) rotary instruments in canals with coronal curvature.

Texting and Walking: Strategies for Postural Control and Implications for Safety

PubMed Central

Schabrun, Siobhan M.; van den Hoorn, Wolbert; Moorcroft, Alison; Greenland, Cameron; Hodges, Paul W.

2014-01-01

There are concerns about the safety of texting while walking. Although evidence of negative effects of mobile phone use on gait is scarce, cognitive distraction, altered mechanical demands, and the reduced visual field associated with texting are likely to have an impact. In 26 healthy individuals we examined the effect of mobile phone use on gait. Individuals walked at a comfortable pace in a straight line over a distance of ∼8.5 m while; 1) walking without the use of a phone, 2) reading text on a mobile phone, or 3) typing text on a mobile phone. Gait performance was evaluated using a three-dimensional movement analysis system. In comparison with normal waking, when participants read or wrote text messages they walked with: greater absolute lateral foot position from one stride to the next; slower speed; greater rotation range of motion (ROM) of the head with respect to global space; the head held in a flexed position; more in-phase motion of the thorax and head in all planes, less motion between thorax and head (neck ROM); and more tightly organized coordination in lateral flexion and rotation directions. While writing text, participants walked slower, deviated more from a straight line and used less neck ROM than reading text. Although the arms and head moved with the thorax to reduce relative motion of the phone and facilitate reading and texting, movement of the head in global space increased and this could negatively impact the balance system. Texting, and to a lesser extent reading, modify gait performance. Texting or reading on a mobile phone may pose an additional risk to safety for pedestrians navigating obstacles or crossing the road. PMID:24465402

Analysis of high-aspect-ratio jet-flap wings of arbitrary geometry

NASA Technical Reports Server (NTRS)

Lissaman, P. B. S.

1973-01-01

An analytical technique to compute the performance of an arbitrary jet-flapped wing is developed. The solution technique is based on the method of Maskell and Spence in which the well-known lifting-line approach is coupled with an auxiliary equation providing the extra function needed in jet-flap theory. The present method is generalized to handle straight, uncambered wings of arbitrary planform, twist, and blowing (including unsymmetrical cases). An analytical procedure is developed for continuous variations in the above geometric data with special functions to exactly treat discontinuities in any of the geometric and blowing data. A rational theory for the effect of finite wing thickness is introduced as well as simplified concepts of effective aspect ratio for rapid estimation of performance.

Transition Within Leeward Plane of Axisymmetric Bodies at Incidence in Supersonic Flow

NASA Technical Reports Server (NTRS)

Tokugawa, Naoko; Choudhari, Meelan; Ishikawa, Hiroaki; Ueda, Yoshine; Fujii, Keisuke; Atobe, Takashi; Li, Fei; Chang, Chau-Lyan; White, Jeffery

2012-01-01

Boundary layer transition along the leeward symmetry plane of axisymmetric bodies at nonzero angle of attack in supersonic flow was investigated experimentally and numerically as part of joint research between the Japan Aerospace Exploration Agency (JAXA) and National Aeronautics and Space Administration (NASA). Transition over four axisymmetric bodies (namely, Sears-Haack body, semi-Sears-Haack body, straight cone and flared cone) with different axial pressure gradients was measured in two different facilities with different unit Reynolds numbers. The semi-Sears-Haack body and flared cone were designed at JAXA to broaden the range of axial pressure distributions. For a body shape with an adverse pressure gradient (i.e., flared cone), the experimentally measured transition patterns show an earlier transition location along the leeward symmetry plane in comparison with the neighboring azimuthal locations. For nearly zero pressure gradient (i.e.,straight cone), this feature is only observed at the larger unit Reynolds number. Later transition along the leeward plane was observed for the remaining two body shapes with a favorable pressure gradient. The observed transition patterns are only partially consistent with the numerical predictions based on linear stability analysis. Additional measurements are used in conjunction with the stability computations to explore the phenomenon of leeward line transition and the underlying transition mechanism in further detail.

Steering Performance, Tactical Vehicles

DTIC Science & Technology

2015-07-29

5 4.1 General Vehicle and Test Characterization ........................... 5 4.2 Weave Test...able to be driven in a straight line without steer input (i.e., “ hands free”). If the vehicle pulls in either direction, the alignment should be...Evaluation Center (AEC) prior to using military personnel as test participants. 4. TEST PROCEDURES. 4.1 General Vehicle and Test

27 CFR 9.233 - Kelsey Bench-Lake County.

Code of Federal Regulations, 2014 CFR

2014-04-01

... mile to the point where the road intersects a straight line drawn westward from the marked 2,493-foot..., approximately 0.8 mile to the first intersection of the eastern boundary of section 26 and the 1,720-foot..., a total distance of approximately 3.25 miles, to the marked 1,439-foot elevation point in section 29...