Effect of heat treatment on mechanical properties of age-hardenable gold alloy at intraoral temperature.

PubMed

Watanabe, I; Watanabe, E; Cai, Z; Okabe, T; Atsuta, M

2001-09-01

The aim of this study was to investigate the effect of various heat treatments on the mechanical properties of gold alloys capable of age-hardening at intraoral temperature. Dumbbell-shaped patterns (ISO 6871) were cast with three gold alloys (Sofard; NC Type-IV; Aurum Cast, NihombashiTokuriki Co.). The Sofard alloy is age-hardenable at intraoral temperature. The castings underwent various heat treatments [as-cast (AC); solution treatment (ST); high-temperature aging (HA); intraoral aging (IA)]. After these heat treatments, ultimate tensile strength (UTS), 0.2% offset yield strength (YS), and elongation (EL) were measured at a strain rate of 1.7x10(-4)/s. Fracture surfaces of the specimens after tensile testing were observed using SEM. Vickers hardness was also measured after heat treating. After IA, the hardness values of the Sofard alloy increased and reached values similar to the hardness of the Sofard specimens aged at high temperature (HA). The hardness values of the NC Type-IV and Aurum Cast specimens slightly increased after IA, but did not reach the values of the specimens after HA. All the Sofard, NC Type-IV and Aurum Cast specimens showed significantly (P<0.05) greater hardness values after HA, compared with the values after any other heat treatments (AC, ST and IA). The UTS and YS of the specimens indicated a tendency similar to the results obtained for hardness. The Sofard specimens with ST showed the greatest elongation compared to the corresponding NC Type-IV and Aurum Cast specimens. However, the elongation of the Sofard specimens was abruptly reduced after intraoral aging. Intraoral aging significantly improved the mechanical properties and hardness of the Sofard alloy.

Grain-Refined AZ92 Alloy with Superior Strength and Ductility

NASA Astrophysics Data System (ADS)

Lee, Jong Un; Kim, Sang-Hoon; Jo, Wan-Kuen; Hong, Won-Hwa; Kim, Woong; Bae, Jun Ho; Park, Sung Hyuk

2018-03-01

Grain-refined AZ92 (GR-AZ92) alloy with superior tensile properties is developed by adding 1 wt% Zn and a very small amount of SiC (0.17 wt%) to commercial AZ91 alloy for enhancing the solid-solution strengthening effect and refining the crystal grains, respectively. The homogenized GR-AZ92 alloy with an average grain size of 91 μm exhibits a tensile yield strength (TYS) of 125 MPa, ultimate tensile strength (UTS) of 281 MPa, and elongation of 12.1%, which are significantly higher than those of AZ91 alloy with a grain size of 420 μm (TYS of 94 MPa, UTS of 192 MPa, and elongation of 7.0%). The peak-aging time of GR-AZ92 alloy (8 h) is significantly shorter than that of AZ91 alloy (32 h) owing to a larger amount of grain boundaries in the former, which serve as nucleation sites of Mg17Al12 precipitates. A short-aging treatment for less than 1 h of the GR-AZ92 alloy causes an effective improvement in its strength without a significant reduction in its ductility. The 30-min-aged GR-AZ92 alloy has an excellent combination of strength and ductility, with a TYS of 142 MPa, UTS of 304 MPa, and elongation of 8.0%.

Prediction of Tensile Strength of Friction Stir Weld Joints with Adaptive Neuro-Fuzzy Inference System (ANFIS) and Neural Network

NASA Technical Reports Server (NTRS)

Dewan, Mohammad W.; Huggett, Daniel J.; Liao, T. Warren; Wahab, Muhammad A.; Okeil, Ayman M.

2015-01-01

Friction-stir-welding (FSW) is a solid-state joining process where joint properties are dependent on welding process parameters. In the current study three critical process parameters including spindle speed (??), plunge force (????), and welding speed (??) are considered key factors in the determination of ultimate tensile strength (UTS) of welded aluminum alloy joints. A total of 73 weld schedules were welded and tensile properties were subsequently obtained experimentally. It is observed that all three process parameters have direct influence on UTS of the welded joints. Utilizing experimental data, an optimized adaptive neuro-fuzzy inference system (ANFIS) model has been developed to predict UTS of FSW joints. A total of 1200 models were developed by varying the number of membership functions (MFs), type of MFs, and combination of four input variables (??,??,????,??????) utilizing a MATLAB platform. Note EFI denotes an empirical force index derived from the three process parameters. For comparison, optimized artificial neural network (ANN) models were also developed to predict UTS from FSW process parameters. By comparing ANFIS and ANN predicted results, it was found that optimized ANFIS models provide better results than ANN. This newly developed best ANFIS model could be utilized for prediction of UTS of FSW joints.

Influence of the welding temperature and the welding speed on the mechanical properties of friction stir welds in EN AW-2219-T87

NASA Astrophysics Data System (ADS)

Bachmann, A.; Krutzlinger, M.; Zaeh, M. F.

2018-06-01

Friction Stir Welding (FSW) is an innovative joining technique, which has proven to produce high quality joints in high strength aluminum alloys. Consequently, it is commonly used to manufacture lightweight aerospace structures with stringent requirements. For these structures, it is necessary to ensure a high ultimate tensile strength (UTS). Various studies have reported that the UTS is significantly influenced by the welding parameters. Samples welded with different parameter sets showed a considerably different UTS, despite being free from detectable welding defects (e.g. tunnel defect, voids, or lack of penetration). Based on the observations in the literature, a hypothesis was posed. The welding temperature along with the welding speed determine the UTS of the weld. This study aims to prove this hypothesis experimentally by using temperature-controlled FSW to join plates of EN AW-2219-T87 in butt joint configuration. The welded samples were examined using visual inspection, metallography, X-ray imaging, and uniaxial tensile tests. Finally, a statistical analysis was conducted. Hereby, the hypothesis was confirmed.

The synchronous improvement of strength and plasticity (SISP) in new Ni-Co based disc superalloys by controling stacking fault energy.

PubMed

Xu, H; Zhang, Z J; Zhang, P; Cui, C Y; Jin, T; Zhang, Z F

2017-08-14

It is a great challenge to improve the strength of disc superalloys without great loss of plasticity together since the microstructures benefiting the strength always do not avail the plasticity. Interestingly, this study shows that the trade-off relationship between strength and plasticity can be broken through decreasing stacking fault energy (SFE) in newly developed Ni-Co based disc superalloys. Axial tensile tests in the temperature range of 25 to 725 °C were carried out in these alloys with Co content ranging from 5% to 23% (wt.%). It is found that the ultimate tensile strength (UTS) and uniform elongation (UE) are improved synchronously when microtwinning is activated by decreasing the SFE at 650 and 725 °C. In contrast, only UTS is improved when stacking fault (SF) dominates the plastic deformation at 25 and 400 °C. These results may be helpful for designing advanced disc superalloys with relatively excellent strength and plasticity simultaneously.

Research and Development of High-Strength of Al-Zn-Mg-Cu Alloys

NASA Astrophysics Data System (ADS)

Vakhromov, R. O.; Antipov, V. V.; Tkachenko, E. A.

The paper is focused on high-strength alloys (UTS=600-650 MPa, specific strength (UTS/density) 220-230 kN•m/kg) which will allow one to retain aluminum's predominant position during the next 15-20 years as applied in advanced aircraft primary structures. Parameters of microstructure (dispersoids, precipitates, degree of recrystallisation, grain size) and properties of semiproducts were studied in dependence on content of base alloying elements in chemical compositions of alloys (total sum of Zn+Mg+Cu — higher than 10 % mass). Contribution of minor additions (Zr, Sc, Ag) to strengthening and creation of improved combination of service properties was investigated. Evolution of phase composition and properties was studied as a dependence of different aging treatments.

Can nature's design be improved upon? High strength, transparent nacre-like nanocomposites with double network of sacrificial cross links.

PubMed

Podsiadlo, Paul; Kaushik, Amit K; Shim, Bong Sup; Agarwal, Ashish; Tang, Zhiyong; Waas, Anthony M; Arruda, Ellen M; Kotov, Nicholas A

2008-11-20

The preparation of a high-strength and highly transparent nacre-like nanocomposite via layer-by-layer assembly technique from poly(vinyl alcohol) (PVA) and Na+-montmorillonite clay nanosheets is reported in this article. We show that a high density of weak bonding interactions between the polymer and the clay particles: hydrogen, dipole-induced dipole, and van der Waals undergoing break-reform deformations, can lead to high strength nanocomposites: sigmaUTS approximately 150 MPa and E' approximately 13 GPa. Further introduction of ionic bonds into the polymeric matrix creates a double network of sacrificial bonds which dramatically increases the mechanical properties: sigmaUTS approximately 320 MPa and E' approximately 60 GPa.

Investigation of the Quasi-Brittle Failure of Alashan Granite Viewed from Laboratory Experiments and Grain-Based Discrete Element Modeling

PubMed Central

Zhang, Luqing; Yang, Duoxing; Braun, Anika; Han, Zhenhua

2017-01-01

Granite is a typical crystalline material, often used as a building material, but also a candidate host rock for the repository of high-level radioactive waste. The petrographic texture—including mineral constituents, grain shape, size, and distribution—controls the fracture initiation, propagation, and coalescence within granitic rocks. In this paper, experimental laboratory tests and numerical simulations of a grain-based approach in two-dimensional Particle Flow Code (PFC2D) were conducted on the mechanical strength and failure behavior of Alashan granite, in which the grain-like structure of granitic rock was considered. The microparameters for simulating Alashan granite were calibrated based on real laboratory strength values and strain-stress curves. The unconfined uniaxial compressive test and Brazilian indirect tensile test were performed using a grain-based approach to examine and discuss the influence of mineral grain size and distribution on the strength and patterns of microcracks in granitic rocks. The results show it is possible to reproduce the uniaxial compressive strength (UCS) and uniaxial tensile strength (UTS) of Alashan granite using the grain-based approach in PFC2D, and the average mineral size has a positive relationship with the UCS and UTS. During the modeling, most of the generated microcracks were tensile cracks. Moreover, the ratio of the different types of generated microcracks is related to the average grain size. When the average grain size in numerical models is increased, the ratio of the number of intragrain tensile cracks to the number of intergrain tensile cracks increases, and the UCS of rock samples also increases with this ratio. However, the variation in grain size distribution does not have a significant influence on the likelihood of generated microcracks. PMID:28773201

Investigation of the Quasi-Brittle Failure of Alashan Granite Viewed from Laboratory Experiments and Grain-Based Discrete Element Modeling.

PubMed

Zhou, Jian; Zhang, Luqing; Yang, Duoxing; Braun, Anika; Han, Zhenhua

2017-07-21

Granite is a typical crystalline material, often used as a building material, but also a candidate host rock for the repository of high-level radioactive waste. The petrographic texture-including mineral constituents, grain shape, size, and distribution-controls the fracture initiation, propagation, and coalescence within granitic rocks. In this paper, experimental laboratory tests and numerical simulations of a grain-based approach in two-dimensional Particle Flow Code (PFC2D) were conducted on the mechanical strength and failure behavior of Alashan granite, in which the grain-like structure of granitic rock was considered. The microparameters for simulating Alashan granite were calibrated based on real laboratory strength values and strain-stress curves. The unconfined uniaxial compressive test and Brazilian indirect tensile test were performed using a grain-based approach to examine and discuss the influence of mineral grain size and distribution on the strength and patterns of microcracks in granitic rocks. The results show it is possible to reproduce the uniaxial compressive strength (UCS) and uniaxial tensile strength (UTS) of Alashan granite using the grain-based approach in PFC2D, and the average mineral size has a positive relationship with the UCS and UTS. During the modeling, most of the generated microcracks were tensile cracks. Moreover, the ratio of the different types of generated microcracks is related to the average grain size. When the average grain size in numerical models is increased, the ratio of the number of intragrain tensile cracks to the number of intergrain tensile cracks increases, and the UCS of rock samples also increases with this ratio. However, the variation in grain size distribution does not have a significant influence on the likelihood of generated microcracks.

The Effect of Scale Dependent Discretization on the Progressive Failure of Composite Materials Using Multiscale Analyses

NASA Technical Reports Server (NTRS)

Ricks, Trenton M.; Lacy, Thomas E., Jr.; Pineda, Evan J.; Bednarcyk, Brett A.; Arnold, Steven M.

2013-01-01

A multiscale modeling methodology, which incorporates a statistical distribution of fiber strengths into coupled micromechanics/ finite element analyses, is applied to unidirectional polymer matrix composites (PMCs) to analyze the effect of mesh discretization both at the micro- and macroscales on the predicted ultimate tensile (UTS) strength and failure behavior. The NASA code FEAMAC and the ABAQUS finite element solver were used to analyze the progressive failure of a PMC tensile specimen that initiates at the repeating unit cell (RUC) level. Three different finite element mesh densities were employed and each coupled with an appropriate RUC. Multiple simulations were performed in order to assess the effect of a statistical distribution of fiber strengths on the bulk composite failure and predicted strength. The coupled effects of both the micro- and macroscale discretizations were found to have a noticeable effect on the predicted UTS and computational efficiency of the simulations.

Precise Analysis of Microstructural Effects on Mechanical Properties of Cast ADC12 Aluminum Alloy

NASA Astrophysics Data System (ADS)

Okayasu, Mitsuhiro; Takeuchi, Shuhei; Yamamoto, Masaki; Ohfuji, Hiroaki; Ochi, Toshihiro

2015-04-01

The effects of microstructural characteristics (secondary dendrite arm spacing, SDAS) and Si- and Fe-based eutectic structures on the mechanical properties and failure behavior of an Al-Si-Cu alloy are investigated. Cast Al alloy samples are produced using a special continuous-casting technique with which it is easy to control both the sizes of microstructures and the direction of crystal orientation. Dendrite cells appear to grow in the casting direction. There are linear correlations between SDAS and tensile properties (ultimate tensile strength σ UTS, 0.2 pct proof strength σ 0.2, and fracture strain ɛ f). These linear correlations, however, break down, especially for σ UTS vs SDAS and ɛ f vs SDAS, as the eutectic structures become more than 3 μm in diameter, when the strength and ductility ( σ UTS and ɛ f) decrease significantly. For eutectic structures larger than 3 μm, failure is dominated by the brittle eutectic phases, for which SDAS is no longer strongly correlated with σ UTS and ɛ f. In contrast, a linear correlation is obtained between σ 0.2 and SDAS, even for eutectic structures larger than 3 μm, and the eutectic structure does not have a strong effect on yield behavior. This is because failure in the eutectic phases occurs just before final fracture. In situ failure observation during tensile testing is performed using microstructural and lattice characteristics. From the experimental results obtained, models of failure during tensile loading are proposed.

Mechanical properties of as-cast and heat-treated ZA-27 alloy/short glass fiber composites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sharma, S.C.; Girish, B.M.; Satish, B.M.

1998-02-01

This paper reports on the mechanical properties of as-cast and heat-treated ZA-27 alloy composites reinforced with glass fibers from 1 to 5 wt%. The composites were fabricated using the Compocasting method, in which short glass fibers were introduced into the vortex created in the molten alloy through an impeller rotated at 500 rpm. The molten mass was thoroughly stirred and poured into permanent molds and squeezed under pressure. The specimens were heat treated at 320 C for 1, 2, 3, and 4 h. The tests on the as-cast composites revealed that as the glass content in the composites was increased,more » the ultimate tensile strength (UTS), compressive strength, and hardness of the composite increased, while the ductility and impact strength were decreased. Heat treatment was found to improve significantly the ductility, compressive strength, and impact strength, while the hardness and UTS were reduced. This paper discusses the behavior of these composites.« less

The development of ultrahigh strength low alloy cast steels with increased toughness

NASA Astrophysics Data System (ADS)

Lynch, Paul C.

This work describes the initial work on the development of the next generation of ultrahigh strength low alloy (UHSLA) cast steels. These UHSLA cast steels have both ultrahigh strength levels and good impact toughness. The influence of heat treatment, secondary processing using hot isostatic processing (HIP), and chemical composition on the microstructure and properties of UHSLA cast steels have been evaluated. The extent of microsegregation reduction expected during the heat treatment of UHSLA cast steels has also been estimated by diffusion modeling. This new family of UHSLA cast steels is similar in composition and properties to UHSLA wrought steels. However, the heat treatment and secondary processing of the UHSLA cast steels is used to develop microstructures and properties typically developed through thermomechanical processing and heat treatment for wrought UHSLA steels. Two martensitic UHSLA steels, 4340+ (silicon modified 4340) and ES-1 were investigated for this study. For the 4340+ alloy, heat treatment variables evaluated include homogenization temperature and time, tempering temperature, and austempering temperature and time. For the ES-1 alloy, heat treatment variables evaluated include homogenization temperature and time, austenization temperature, cryogenic treatment, and tempering temperature. The effect of high temperature hot isostatic processing (HIP) on the 4340+ and ES- 1 alloys was also investigated. Tensile properties, charpy v-notch impact toughness (CVN), microstructures, and fractographs have all been characterized after heat treatment. The effects of HIP on microporosity reduction in the ES-1 alloy were also investigated. The experiments carried out on the investment cast 4340+ alloy have shown that increasing the homogenization temperature can increase CVN without changing the ultimate tensile strength (UTS) or yield strength (YS) of the cast material. By replacing the homogenization step in the conventional heat treatment process with a high temperature HIP treatment, both the CVN and ductility of the alloy was found to increase while maintaining comparable ultimate tensile strength (UTS) and yield strength (YS) levels as compared to the original homogenization treatment. Austempering the (IC) 4340+ material led to a significant increase in CVN and ductility at the expense of UTS and yield strength as the primarily martensitic microstructure was converted to a mixed martensitic-bainitic structure. An initial heat of induction melted, aluminum deoxidized investment cast ES-1 with 0.06 wt % of aluminum showed that the average -40°F and +72°F impact toughness, % elongation, and UTS and YS of the fully heat treated investment cast + HIP ES-1 material lagged significantly behind that of the vacuum degassed cast + HIP ES-1 ingot material. Even though the % elongation and impact toughness of the investment cast ES-1 material changed between heat treatment conditions, the average UTS and YS values remained relatively unchanged throughout the heat treatments for the investment cast study. Etched micrographs of the investment cast ES-1 material showed evidence of significant differences in microsegregation reduction between the samples homogenized at 2125°F for 4 hours and those not homogenized at 2125°F for 4 hours. SEM fracture surface work performed on the investment cast material clearly showed that the induction melted investment and aluminum killed cast material contained significant amounts of MnS and Al2O3 inclusions that were not discovered in the vacuum degassed cast ingot material. Lastly, the results of a third heat of induction melted, aluminum deoxidized investment cast ES-1 material possessing just 0.01wt% of aluminum showed that the decrease in aluminum content from the first experimental heat did not improve the mechanical properties of the investment cast material. (Abstract shortened by UMI.)

Pre-heated dual-cured resin cements: analysis of the degree of conversion and ultimate tensile strength.

PubMed

França, Flávio Álvares; Oliveira, Michele de; Rodrigues, José Augusto; Arrais, César Augusto Galvão

2011-01-01

This study evaluated the degree of conversion (DC) and ultimate tensile strength (UTS) of dual-cured resin cements heated to 50º C prior to and during polymerization. Disc- and hourglass-shaped specimens of Rely X ARC (RX) and Variolink II (VII) were obtained using addition silicon molds. The products were manipulated at 25º C or 50º C and were subjected to 3 curing conditions: light-activation through a glass slide or through a pre-cured 2-mm thick resin composite disc, or they were allowed to self-cure (SC). All specimens were dark-stored dry for 15 days. For DC analysis, the resin cements were placed into the mold located on the center of a horizontal diamond on the attenuated total reflectance element in the optical bench of a Fourier Transformed Infrared spectrometer. Infrared spectra (n = 6) were collected between 1680 and 1500 cm-1, and DC was calculated by standard methods using changes in ratios of aliphatic-to-aromatic C=C absorption peaks from uncured and cured states. For UTS test, specimens (n = 10) were tested in tension in a universal testing machine (crosshead speed of 1 mm/min) until failure. DC and UTS data were submitted to 2-way ANOVA, followed by Tukey's test (α= 5%). Both products showed higher DC at 50º C than at 25º C in all curing conditions. No significant difference in UTS was noted between most light-activated groups at 25º C and those at 50º C. VII SC groups showed higher UTS at 50º C than at 25º C (p < 0.05). Increased temperature led to higher DC, but its effects on resin cement UTS depended on the curing condition.

Ultrasound phonophoresis of panax notoginseng improves the strength of repairing ligament: a rat model.

PubMed

Ng, Gabriel Y F; Wong, Richard Y F

2008-12-01

This study examined the phonophoretic effect of a therapeutic ultrasound coupled with a Panax notoginseng (PN) gel and compared it with a therapeutic ultrasound alone for medial collateral ligament repair in rats. Twenty mature male Sprague-Dawley rats receiving surgical transection to the left medial collateral ligament (MCL) were divided randomly into three groups: ultrasound (US, n = 7), ultrasound with PN coupling gel (PNUS, n = 7) and control (n = 6). The treatments started on day 3 after surgery for six days per week over a two-week period. The US group received 4 min of pulsed ultrasound (1 MHz) at the intensity of 0.5W/cm(2) with a normal ultrasonic coupling gel. The PNUS group received the same ultrasound treatment, but with a coupling gel that contained PN extract. The control group received a placebo ultrasound treatment similar to the other two groups. On day 17, the ligaments were mechanically tested for load-relaxation, stiffness and ultimate tensile strength (UTS). Values of the left side were normalized against that of the right side of each animal for analysis. Results revealed significantly higher normalized stiffness (p = 0.009) and UTS (p = 0.022) in the PNUS group than the other two groups, but insignificant difference in load-relaxation among all groups. This study reveals a positive ultrasonic phonophoretic effect of Panax notoginseng extract for improving the strength of ligament repair than ultrasound therapy alone.

Optimizing pulsed Nd:YAG laser beam welding process parameters to attain maximum ultimate tensile strength for thin AISI316L sheet using response surface methodology and simulated annealing algorithm

NASA Astrophysics Data System (ADS)

Torabi, Amir; Kolahan, Farhad

2018-07-01

Pulsed laser welding is a powerful technique especially suitable for joining thin sheet metals. In this study, based on experimental data, pulsed laser welding of thin AISI316L austenitic stainless steel sheet has been modeled and optimized. The experimental data required for modeling are gathered as per Central Composite Design matrix in Response Surface Methodology (RSM) with full replication of 31 runs. Ultimate Tensile Strength (UTS) is considered as the main quality measure in laser welding. Furthermore, the important process parameters including peak power, pulse duration, pulse frequency and welding speed are selected as input process parameters. The relation between input parameters and the output response is established via full quadratic response surface regression with confidence level of 95%. The adequacy of the regression model was verified using Analysis of Variance technique results. The main effects of each factor and the interactions effects with other factors were analyzed graphically in contour and surface plot. Next, to maximum joint UTS, the best combinations of parameters levels were specified using RSM. Moreover, the mathematical model is implanted into a Simulated Annealing (SA) optimization algorithm to determine the optimal values of process parameters. The results obtained by both SA and RSM optimization techniques are in good agreement. The optimal parameters settings for peak power of 1800 W, pulse duration of 4.5 ms, frequency of 4.2 Hz and welding speed of 0.5 mm/s would result in a welded joint with 96% of the base metal UTS. Computational results clearly demonstrate that the proposed modeling and optimization procedures perform quite well for pulsed laser welding process.

Cardiac findings in Quarter Horses with heritable equine regional dermal asthenia.

PubMed

Brinkman, Erin L; Weed, Benjamin C; Patnaik, Sourav S; Brazile, Bryn L; Centini, Ryan M; Wills, Robert W; Olivier, Bari; Sledge, Dodd G; Cooley, Jim; Liao, Jun; Rashmir-Raven, Ann M

2017-03-01

OBJECTIVE To compare biomechanical and histologic features of heart valves and echocardiographic findings between Quarter Horses with and without heritable equine regional dermal asthenia (HERDA). DESIGN Prospective case-control study. ANIMALS 41 Quarter Horses. PROCEDURES Ultimate tensile strength (UTS) of aortic and mitral valve leaflets was assessed by biomechanical testing in 5 horses with HERDA and 5 horses without HERDA (controls). Histologic evaluation of aortic and mitral valves was performed for 6 HERDA-affected and 3 control horses. Echocardiography was performed in 14 HERDA-affected and 11 control horses. Biomechanical data and echocardiographic variables of interest were compared between groups by statistical analyses, RESULTS Mean values for mean and maximum UTS of heart valves were significantly lower in HERDA-affected horses than in controls. Blood vessels were identified in aortic valve leaflets of HERDA-affected but not control horses. Most echocardiographic data did not differ between groups. When the statistical model for echocardiographic measures was controlled for body weight, mean and maximum height and width of the aorta at the valve annulus in short-axis images were significantly associated with HERDA status and were smaller for affected horses. CONCLUSIONS AND CLINICAL RELEVANCE Lower UTS of heart valves in HERDA-affected horses, compared with those of control horses, supported that tissues other than skin with high fibrillar collagen content are abnormal in horses with HERDA. Lack of significant differences in most echocardiographic variables between affected and control horses suggested that echocardiography may not be useful to detect a substantial loss of heart valve tensile strength. Further investigation is warranted to confirm these findings. Studies in horses with HERDA may provide insight into cardiac abnormalities in people with collagen disorders.

Effect of ultrasound on electrochemical chloride extraction from mortar

NASA Astrophysics Data System (ADS)

Chen, Yiqun; Yao, Wu; Zuo, Junqing

2018-03-01

In this paper, the effect of auxiliary ultrasound on electrochemical chloride extraction (ECE) was studied. The chloride removal efficiency was investigated by examining the chloride content with ultrasound-assisted ECE and changing the introducing time of ultrasound. The experimental results showed that removal of chloride ions was noted to be more effective in ECE treatment assisted with ultrasound treatment (UT). In addition, the lower w/c ratio led to more distinct effect of ultrasonic cavitation on chloride removal. Electrochemical behaviors measured with different treatment revealed that UT treatment was effective on moderating the corrosion condition. Microstructural analyses revealed a significant alteration in composition and morphology of cementitious phases with UT treatment. Pull-out tests indicated that ultrasound had a certain negative impact on the bond strength. Although the effect of introducing ultrasound in the first 2 weeks or the last 2 weeks on the extraction efficiency was not obvious, intermittent ultrasound could not only ensure the chloride extraction efficiency, but also reduce the adverse effect of ultrasound on the bond strength.

[The effects of different welding wires on the mechanical properties of laser welding joints].

PubMed

Huang, Qing-feng; Zhang, Jian-zhong; Jiang, Wei-dong; Li, Quan; Yu, Jin-xing

2006-08-01

To evaluate the mechanical properties and microstructure of laser-welded joints with different welding wires for clinical use of welding wire. The standard tensile test and three-point bending test rods were made from Co-Cr and Ni-Cr alloy, and were laser-welded with different welding wire (commercially welding wire and casting wire). Then the tensile rods were tested for the ultimate tensile strength (UTS), and the bending rods for the ultimate bending strength (UBS). The results was analyzed by one-way ANOVA. The tensile fracture surface were examined by scanning electron microscopy (SEM). Metallurgical analysis were also performed on polished longitudinal sectioned samples. For Co-Cr alloy, the UTS of casting wire group and commercially welding wire group was respectively (606.40+/-82.53)MPa and (693.61+/-47.68)MPa; the UBS was respectively (997.95+/-88.89)MPa and (1160.76+/-91.59)MPa. ANOVA showed a significant difference of UTS and UBS between the two groups at the 0.05 level (P<0.05). For Ni-Cr alloy, the UTS of casting wire group and commercially welding wire group was respectively (558.14+/-46.75)MPa and (582.32+/-35.43)MPa; the UBS was respectively (1084.75+/-46.02)MPa and (1078.29+/-36.25)MPa. There was no significant difference between the two groups (P>0.05). SEM and metallurgical examination showed the welded zone exhibiting more cracks in the casting wire group than in the commercially welding wire group. It would be advisable to work with commercially welding wire for the joints that need better strength.

Effects of Sn addition on the microstructure and tensile properties of AX55 alloys

NASA Astrophysics Data System (ADS)

Qiu, K. Q.; Huang, P.

2018-04-01

The microstructures and tensile properties at both room and elevated temperatures for both the as-cast and as-aged Mg-5Al-5Ca (AX55) alloy with 0–2 wt% Sn addition were studied. The results indicate that the α-Mg dendrite is gradually refined and the interdendritic Al2Ca and Mg2Ca intermetallics become more connected with Sn addition. The as-cast AX55-1Sn alloy shows optimal ultimate tensile strength (UTS) at testing temperature from 25 to 225 °C. After T61 and T62 heat treatment, the eutectic-lamellar microstructure of the as-cast alloys tends to be spheroidized and distributed uniformly along the grain boundaries. While the alloys with higher Sn content show higher density of granulated and needle-shaped Al2Ca phases precipitated into α-Mg matrix, which results in the increase of UTS, yield strength (YS), elongation and microhardness with Sn addition. The morphology of CaMgSn phase can be improved by T62 treatment, which makes as-aged AX55-2.0Sn alloy exhibit a smaller decrease rate of the UTS at temperature up to 225 °C. The heat resistance of different heat-resistant magnesium alloys were compared and discussed by using the decrease rate of the UTS.

Orientation and size dependence of the elastic properties of zinc oxide nanobelts

NASA Astrophysics Data System (ADS)

Kulkarni, A. J.; Zhou, M.; Ke, F. J.

2005-12-01

Molecular dynamics simulations are performed to characterize the response of zinc oxide (ZnO) nanobelts to tensile loading. The ultimate tensile strength (UTS) and Young's modulus are obtained as functions of size and growth orientation. Nanobelts in three growth orientations are generated by assembling the unit wurtzite cell along the [0001], [01\\bar {1} 0] , and [2\\bar {1} \\bar {1}0] crystalline axes. Following the geometric construction, dynamic relaxation is carried out to yield free-standing nanobelts at 300 K. Two distinct configurations are observed in the [0001] and [01\\bar {1} 0] orientations. When the lateral dimensions are above 10 Å, nanobelts with rectangular cross-sections are seen. Below this critical size, tubular structures involving two concentric shells similar to double-walled carbon nanotubes are obtained. Quasi-static deformations of belts with [2\\bar {1} \\bar {1} 0] and [01\\bar {1} 0] orientations consist of three stages, including initial elastic stretching, wurtzite-ZnO to graphitic-ZnO structural transformation, and cleavage fracture. On the other hand, [0001] belts do not undergo any structural transformation and fail through cleavage along (0001) planes. Calculations show that the UTS and Young's modulus of the belts are size dependent and are higher than the corresponding values for bulk ZnO. Specifically, as the lateral dimensions increase from 10 to 40 Å, decreases between 38-76% and 24-63% are observed for the UTS and Young's modulus, respectively. This effect is attributed to the size-dependent compressive stress induced by tensile surface stress in the nanobelts. [01\\bar {1} 0] and [2\\bar {1} \\bar {1} 0] nanobelts with multi-walled tubular structures are seen to have higher values of elastic moduli (~340 GPa) and UTS (~36 GPa) compared to their wurtzite counterparts, echoing a similar trend in multi-walled carbon nanotubes.

Yttria Nanoparticle Reinforced Commercially Pure (CP) Titanium

DTIC Science & Technology

2011-09-01

nanoparticles as well as titanium boride (TiB) reinforcements were produced through gas atomization. After consolidation and extrusion, room temperature...pure FE iron O oxygen Ti titanium TiB titanium boride TYS tensile yield strength UTS ultimate tensile strength wt% weight percent Y2O3

The Astronomical Almanac Online - Glossary

Science.gov Websites

Astronomical Almanac. Δ A B C D E F G H I J K L M N O P Q R S T U V W X Y Z $\\boldmath{\\Delta {\\rm T}}$: the difference between Terrestrial Time (TT) and Universal Time (UT): $\\Delta {\\rm T} = {\\rm TT} - {\\rm UT}1 $. $\\boldmath{\\Delta {\\rm UT1}}$ (or $\\boldmath{\\Delta {\\rm UT}}$): the value of the difference between

Anisotropic Responses of Mechanical and Thermal Processed Cast Al-Si-Mg-Cu Alloy

NASA Astrophysics Data System (ADS)

Adeosun, S. O.; Akpan, E. I.; Balogun, S. A.; Onoyemi, O. K.

2015-05-01

The effects of ambient directional rolling and heat treatments on ultimate tensile strength (UTS), hardness (HD), percent elongation (PE), and impact energy (IE) on Al-Si-Mg-Cu alloy casting with reference to inclination to rolling direction are discussed in this article. The results show that rolled and quenched (CQ) sample possess superior UTS and HD to as-cast and those of rolled and aged samples (CA). Improved IE resistance with ductility is shown by both CQ and CA samples. However, these mechanical properties are enhanced as changes in the test sample direction moved away from rolling direction for all heat-treated samples. The CQ samples displayed highest tensile strength (108 MPa) and PE (19.8%) in the 90° direction.

Fabrication and Characterization of Plasma-Sprayed Carbon-Fiber-Reinforced Aluminum Composites

NASA Astrophysics Data System (ADS)

Xiong, Jiang-tao; Zhang, Hao; Peng, Yu; Li, Jing-long; Zhang, Fu-sheng

2018-04-01

Carbon fiber ( C f)/Al specimens were fabricated by plasma-spraying aluminum powder on unidirectional carbon fiber bundles (CFBs) layer by layer, followed by a densification heat treatment process. The microstructure and chemical composition of the C f/Al composites were examined by scanning electron microscopy and energy-dispersive spectrometry. The CFBs were completely enveloped by aluminum matrix, and the peripheral regions of the CFBs were wetted by aluminum. In the wetted region, no significant Al4C3 reaction layer was found at the interface between the carbon fibers and aluminum matrix. The mechanical properties of the C f/Al specimens were evaluated. When the carbon fiber volume fraction (CFVF) was 9.2%, the ultimate tensile strength (UTS) of the C f/Al composites reached 138.3 MPa with elongation of 4.7%, 2.2 times the UTS of the Al matrix (i.e., 63 MPa). This strength ratio (between the UTS of C f/Al and the Al matrix) is higher than for most C f/Al composites fabricated by the commonly used method of liquid-based processing at the same CFVF level.

The variability and IRI2007-predictability of hmF2 over South Africa

NASA Astrophysics Data System (ADS)

Mbambo, M. C.; McKinnell, Lee-Anne; Habarulema, J. B.

2013-11-01

This paper presents an investigation into the variability and predictability of the maximum height of the ionospheric F2 layer, hmF2 over the South African region. Data from three South African stations, namely Madimbo (22.4°S, 26.5°E, dip angle: -61.47°), Grahamstown (33.3°S, 26.5°E, dip angle: -64.08°) and Louisvale (28.5°S, 21.2°E, dip angle: -65.44°) were used in this study. The results indicate that hmF2 shows a larger variability around midnight than during the daytime for all seasons. Monthly median hmF2 values were used in all cases and were compared with predictions from the IRI-2007 model, using the URSI (Union Radio-Scientifique Internationale) coefficient option. The analysis covers the diurnal and seasonal hourly hmF2 values for the selected months and time sectors e.g. January, July, April and October for 2003 and 2005. The time ranges between (03h00-23h00 UT; LT = UT + 2h) representing the local sunrise, midday, sunset and midnight hours. The time covers sunrise, midday, sunrise, and midnight hours (03-06h00 UT, 07-11h00 UT, sunrise 16-18h00 UT and 22-23h00 UT; LT = UT + 2h). The dependence of the results on solar activity levels was also investigated. The IRI-2007 predictions follow fairly well the diurnal and seasonal variation patterns of the observed hmF2 values at all the stations. However, the IRI-2007 model overestimates and underestimates the hmF2 value during different months for all the solar activity periods.

Ultra-Rapid dUT1 Measurements on Japan-Fennoscandian Baselines - Application to 24-hour Sessions

NASA Technical Reports Server (NTRS)

Matsuzaka, Shigeru; Kurihara, Shinobu; Sekido, Mamoru; Hobiger, Thomas; Haas, Rudiger; Ritakari, Jouko; Wagner, Jan

2010-01-01

GSI, NICT, OSO, and MRO have been engaged in Ultra-rapid dUT1 experiments since 2007 aiming at the technological possibility of real-time dUT1 results using the e-VLBI technique. We have already successfully determined dUT1 in less than four minutes after the end of an experimental Intensive session in 2008, and at present we routinely get the results within 30 minutes for regular Intensives. In 2009 we applied the technique to 24-hour sessions and continuously obtained dUT1 values by processing and analyzing Tsukuba Onsala data in near real-time. It showed a detailed behavior of UT1 variations, which could be very valuable for scientific study as well as for precise prediction of UT1-UTC.

Evaluation of tensile strength and surface topography of orthodontic wires after infection control procedures: An in vitro study

PubMed Central

Brindha, M.; Kumaran, N. Kurunji; Rajasigamani, K.

2014-01-01

Aim: The aim of this study is to evaluate, the influence of four types of sterilization/disinfection procedures (autoclave, hot air oven, glutaraldehyde, and ultraviolet [UV] light) on the tensile strength and surface topography of three orthodontic wires (stainless steel (SS), titanium - molybdenum alloy [TMA], and cobalt chromium (CoCr)). Materials and Methods: Sample comprised of three types of 8 inches straight length segments of orthodontic wires. They were divided into three groups according to wire composition comprising of 50 samples each. Totally 50 samples of each group were then equally divided into five subgroups according to sterilization method. After sterilization and disinfection of the experimental group, surface topography was examined with scanning electron microscope (SEM) and tensile strength was tested using universal testing machine. Result: The results of this study show that the mean ultimate tensile strength (UTS) of SS wire after four sterilization procedures were similar to the control group (1845.815 ± 142.29 MPa). The mean UTS of TMA wire increases after four sterilization procedures when compared with the control group (874.107 ± 275.939 MPa). The mean UTS of CoCr wire remains same after UV light disinfection, but increases after other three sterilization procedures when compared with the control group (1449.759 ± 156.586 MPa). SEM photographs of the present study shows gross increase in pitting roughness of the surface topography of all the three types of wires after four types of sterilization. Conclusion: Orthodontists who want to offer maximum safety for their patients can sterilize orthodontic wires before placement, as it does not deteriorate the tensile strength and surface roughness of the alloys. PMID:25210383

Evaluation of tensile strength and surface topography of orthodontic wires after infection control procedures: An in vitro study.

PubMed

Brindha, M; Kumaran, N Kurunji; Rajasigamani, K

2014-07-01

The aim of this study is to evaluate, the influence of four types of sterilization/disinfection procedures (autoclave, hot air oven, glutaraldehyde, and ultraviolet [UV] light) on the tensile strength and surface topography of three orthodontic wires (stainless steel (SS), titanium - molybdenum alloy [TMA], and cobalt chromium (CoCr)). Sample comprised of three types of 8 inches straight length segments of orthodontic wires. They were divided into three groups according to wire composition comprising of 50 samples each. Totally 50 samples of each group were then equally divided into five subgroups according to sterilization method. After sterilization and disinfection of the experimental group, surface topography was examined with scanning electron microscope (SEM) and tensile strength was tested using universal testing machine. The results of this study show that the mean ultimate tensile strength (UTS) of SS wire after four sterilization procedures were similar to the control group (1845.815 ± 142.29 MPa). The mean UTS of TMA wire increases after four sterilization procedures when compared with the control group (874.107 ± 275.939 MPa). The mean UTS of CoCr wire remains same after UV light disinfection, but increases after other three sterilization procedures when compared with the control group (1449.759 ± 156.586 MPa). SEM photographs of the present study shows gross increase in pitting roughness of the surface topography of all the three types of wires after four types of sterilization. Orthodontists who want to offer maximum safety for their patients can sterilize orthodontic wires before placement, as it does not deteriorate the tensile strength and surface roughness of the alloys.

High Tensile Strength of Engineered β-Solenoid Fibrils via Sonication and Pulling.

PubMed

Peng, Zeyu; Parker, Amanda S; Peralta, Maria D R; Ravikumar, Krishnakumar M; Cox, Daniel L; Toney, Michael D

2017-11-07

We present estimates of ultimate tensile strength (UTS) for two engineered β-solenoid protein mutant fibril structures (spruce budworm and Rhagium inquisitor antifreeze proteins) derived from sonication-based measurements and from force pulling molecular dynamics simulations, both in water. Sonication experiments generate limiting scissioned fibrils with a well-defined length-to-width correlation for the mutant spruce budworm protein and the resultant UTS estimate is 0.66 ± 0.08 GPa. For fibrils formed from engineered R. inquisitor antifreeze protein, depending upon geometry, we estimate UTSs of 3.5 ± 3.2-5.5 ± 5.1 GPa for proteins with interfacial disulfide bonds, and 1.6 ± 1.5-2.5 ± 2.3 GPa for the reduced form. The large error bars for the R. inquisitor structures are intrinsic to the broad distribution of limiting scission lengths. Simulations provide pulling velocity-dependent UTSs increasing from 0.2 to 1 GPa in the available speed range, and 1.5 GPa extrapolated to the speeds expected in the sonication experiments. Simulations yield low-velocity values for the Young's modulus of 6.0 GPa. Without protein optimization, these mechanical parameters are similar to those of spider silk and Kevlar, but in contrast to spider silk, these proteins have a precisely known sequence-structure relationship. Copyright © 2017 Biophysical Society. Published by Elsevier Inc. All rights reserved.

Influence of multiple-passes on microstructure and mechanical properties of Al-Mg/SiC surface composites fabricated via underwater friction stir processing

NASA Astrophysics Data System (ADS)

Srivastava, Manu; Rathee, Sandeep; Maheshwari, Sachin; Siddiquee, Arshad Noor

2018-06-01

Friction stir processing (FSP) is a relatively newly developed solid-state process involving surface modifications for fabricating metal matrix surface composites. Obtaining metal matrix nano-composites with uniform dispersion of reinforcement particles via FSP route is an intricate task to accomplish. In this work, AA5059/SiC nano surface composites (SCs) were developed. Effect of multiple FSP passes and SiC addition on microstructure and mechanical properties of fabricated SCs during underwater condition was investigated. Results reflected that the average microhardness value of base metal (BM) increases from 85 Hv to 159 Hv in stir zone of four pass underwater friction stir processed (FSPed) SC. Highest ultimate tensile strength (UTS) achieved during four pass FSPed sample was 377 MPa that is higher than UTS of BM (321 MPa) and four pass FSPed sample developed at ambient air FSP conditions (347 MPa). An appreciably narrower heat affected zone is obtained owing to fast cooling and reduced heat conduction during underwater FSP, amounting to higher UTS as compared to BM and SC at ambient conditions. Thus, it can be concluded that surrounding medium and number of FSP passes have significant impact on mechanical properties of fabricated SCs. Analysis of microstructures and distribution of SiC particles in fabricated SCs were studied by optical microscope and FESEM respectively and found in good corroboration with the mechanical properties.

Al2O3 Nanoparticle Addition to Commercial Magnesium Alloys: Multiple Beneficial Effects

PubMed Central

Paramsothy, Muralidharan; Chan, Jimmy; Kwok, Richard; Gupta, Manoj

2012-01-01

The multiple beneficial effects of Al2O3 nanoparticle addition to cast magnesium based systems (followed by extrusion) were investigated, constituting either: (a) enhanced strength; or (b) simultaneously enhanced strength and ductility of the corresponding magnesium alloys. AZ31 and ZK60A nanocomposites containing Al2O3 nanoparticle reinforcement were each fabricated using solidification processing followed by hot extrusion. Compared to monolithic AZ31 (tension levels), the corresponding nanocomposite exhibited higher yield strength (0.2% tensile yield strength (TYS)), ultimate strength (UTS), failure strain and work of fracture (WOF) (+19%, +21%, +113% and +162%, respectively). Compared to monolithic AZ31 (compression levels), the corresponding nanocomposite exhibited higher yield strength (0.2% compressive yield strength (CYS)) and ultimate strength (UCS), lower failure strain and higher WOF (+5%, +5%, −4% and +11%, respectively). Compared to monolithic ZK60A (tension levels), the corresponding nanocomposite exhibited lower 0.2% TYS and higher UTS, failure strain and WOF (−4%, +13%, +170% and +200%, respectively). Compared to monolithic ZK60A (compression levels), the corresponding nanocomposite exhibited lower 0.2% CYS and higher UCS, failure strain and WOF (−10%, +7%, +15% and +26%, respectively). The capability of Al2O3 nanoparticles to enhance the properties of cast magnesium alloys in a way never seen before with micron length scale reinforcements is clearly demonstrated. PMID:28348301

Clinical utility of third-trimester uterine artery Doppler in the prediction of brain hemodynamic deterioration and adverse perinatal outcome in small-for-gestational-age fetuses.

PubMed

Cruz-Martinez, R; Savchev, S; Cruz-Lemini, M; Mendez, A; Gratacos, E; Figueras, F

2015-03-01

To assess the clinical value of third-trimester uterine artery (UtA) Doppler ultrasound in the prediction of hemodynamic deterioration and adverse perinatal outcome in term small-for-gestational-age (SGA) fetuses. UtA Doppler parameters, cerebroplacental ratio (CPR) and fetal middle cerebral artery (MCA) pulsatility index (PI) were evaluated weekly, starting from the time of SGA diagnosis until 24 h before induction of labor, in a cohort of 327 SGA fetuses with normal umbilical artery PI (< 95th centile), delivered at > 37 weeks' gestation. Differences in the sequence of CPR and MCA-PI changes < 5th centile, between the group with normal UtA Doppler indices at diagnosis and those with abnormal UtA indices, were analyzed by survival analysis. In addition, the use of UtA Doppler value, alone or in combination with a brain Doppler scan before delivery, to predict the risk of Cesarean section, Cesarean section for non-reassuring fetal status (NRFS), neonatal acidosis and neonatal hospitalization was evaluated by logistic regression analysis, adjusted for gestational age at birth and birth-weight percentile. Abnormal UtA Doppler at diagnosis of SGA was associated with a higher risk of developing abnormal brain Doppler indices before induction of labor than in those with a normal UtA at diagnosis (62.7% vs 34.6%, respectively; P < 0.01). Compared to those with normal UtA Doppler indices, those with abnormal UtA Doppler findings were associated with a higher risk of intrapartum Cesarean section (52.2% vs 37.3%, respectively; P = 0.03), Cesarean section for NRFS (35.8% vs 23.1%, respectively; P = 0.03), neonatal acidosis (10.4% vs 7.7%, respectively; P = 0.47) and neonatal hospitalization (23.9% vs 16.5%, respectively; P = 0.16). Logistic regression analysis indicated that UtA Doppler findings were not significantly associated with adverse perinatal outcome independent of brain Doppler findings. UtA Doppler indices predict adverse perinatal outcome, but do not help to improve the predictive value of brain Doppler indices. However, at the time of SGA diagnosis they identify the subgroup of fetuses at highest risk of progression to abnormal brain Doppler findings. Copyright © 2014 ISUOG. Published by John Wiley & Sons Ltd.

Investigation of thermal aging effects on the tensile properties of Alloy 617 by in-situ synchrotron wide-angle X-ray scattering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Xiang; Mo, Kun; Miao, Yinbin

The nickel-base Alloy 617 has been considered as the lead candidate structural material for the intermediate heat exchanger (IHX) of the Very-High-Temperature Reactor (VHTR). In order to assess the long-term performance of Alloy 617, thermal aging experiments up to 10,000 h in duration were performed at 1000 degrees C. Subsequently, in-situ synchrotron wide-angle X-ray scattering (WAXS) tensile tests were carried out at ambient temperature. M23C6 carbides were identified as the primary precipitates, while a smaller amount of M6C was also observed. The aging effects were quantified in several aspects: (1) macroscopic tensile properties, (2) volume fraction of the M23C6 Phase,more » (3) the lattice strain evolution of both the matrix and the M23C6 precipitates, and (4) the dislocation density evolution during plastic deformation. The property-microstructure relationship is described with a focus on the evolution of the M23C6 phase. For aging up to 3000 h, the yield strength (YS) and ultimate tensile strength (UTS) showed little variation, with average values being 454 MPa and 787 MPa, respectively. At 10,000 h, the YS and UTS reduced to 380 MPa and 720 MPa, respectively. The reduction in YS and UTS is mainly due to the coarsening of the M23C6 Precipitates. After long term aging, the volume fraction of the M23C6 phase reached a plateau and its maximum internal stress was reduced, implying that under large internal stresses the carbides were more susceptible to fracture or decohesion from the matrix. Finally, the calculated dislocation densities were in good agreement with transmission electron microscopy (TEM) measurements. The square roots of the dislocation densities and the true stresses displayed typical linear behavior and no significant change was observed in the alloys in different aging conditions.« less

Tensile properties and water absorption assessment of linear low-Density Polyethylene/Poly (Vinyl Alcohol)/Kenaf composites: effect of eco-friendly coupling agent

NASA Astrophysics Data System (ADS)

Pang, A. L.; Ismail, H.; Abu Bakar, A.

2018-02-01

Linear low-density polyethylene (LLDPE)/poly (vinyl alcohol) (PVOH) filled with untreated kenaf (UT-KNF) and eco-friendly coupling agent (ECA)-treated kenaf (ECAT-KNF) were prepared using ThermoHaake internal mixer, respectively. Filler loadings of UT-KNF and ECAT-KNF used in this study are 10 and 40 parts per hundred parts of resin (phr). The effect of ECA on tensile properties and water absorption of LLDPE/PVOH/KNF composites were investigated. Field emission scanning electron microscopy (FESEM) analysis was applied to visualize filler-matrix adhesion. The results indicate LLDPE/PVOH/ECAT-KNF composites possess higher tensile strength and tensile modulus, but lower elongation at break compared to LLDPE/PVOH/UT-KNF composites. The morphological studies of tensile fractured surfaces using FESEM support the increment in tensile properties of LLDPE/PVOH/ECAT-KNF composites. Nevertheless, LLDPE/PVOH/UT-KNF composites reveal higher water absorption compared to LLDPE/PVOH/ECAT-KNF composites.

Can extended photoactivation time of resin-based fissure sealer materials improve ultimate tensile strength and decrease water sorption/solubility?

PubMed

Borges, Boniek Castillo Dutra; Souza-Júnior, Eduardo José; Catelan, Anderson; Paulillo, Luís Alexandre Maffei Sartini; Aguiar, Flávio Henrique Baggio

2012-10-01

This study aimed to evaluate the impact of extended photoactivation time on ultimate tensile strength (UTS), water sorption (WS) and solubility (WSB) of resin-based materials used as fissure-sealants. A fissure-sealant (Fluroshield) and a flowable composite (Permaflo) polymerized for 20 and 60 seconds were tested. For UTS, 20 hourglass shaped samples were prepared representing two materials and two photoactivation time (n=5). After 24-h dry-storage, samples were tested in tension using a universal testing machine at a cross-head speed of 0.5 mm/min (UTS was calculated in MPa). For WS and WSB, 20 disks with 5 mm diameter and 1 mm height (n=5) were prepared and volumes were calculated (mm(3)). They were transferred to desiccators until a constant mass was obtained (m1) and were subsequently immersed in distilled water until no alteration in mass was detected (m2). Samples were reconditioned to constant mass in desiccators (m3). WS and WSB were determined using the equations m2-m3/V and m1-m3/V, respectively. Data were subjected to two-way ANOVA and Tukey's HSD test (P<.05). There was no significant difference between materials or photoactivation times for the UTS and WS. Permaflo presented lower but negative WSB compared to Fluroshield. Extended photoactivation time did not improve the physical properties tested. Fluroshield presented physical properties that were similar to or better than Permaflo.

Proceedings: ecology and management of pinyon-juniper communities within the Interior West; 1997 September 15-18; Provo, UT

Treesearch

Stephen B. Monsen; Richard Stevens

1999-01-01

A symposium held September 15-18,1997, in Provo, UT, and Sanpete County, UT, provided information on the ecology, management, resource values, and restoration of pinyon-juniper communities in the Interior Western United States. The conference was hosted by the USDA Forest Service, Rocky Mountain Research Station and the Utah Division of Wildlife Resources in...

Microstructure and Mechanical Properties of Fiber-Laser-Welded and Diode-Laser-Welded AZ31 Magnesium Alloy

NASA Astrophysics Data System (ADS)

Chowdhury, S. M.; Chen, D. L.; Bhole, S. D.; Powidajko, E.; Weckman, D. C.; Zhou, Y.

2011-07-01

The microstructures, tensile properties, strain hardening, and fatigue strength of fiber-laser-welded (FLW) and diode-laser-welded (DLW) AZ31B-H24 magnesium alloys were studied. Columnar dendrites near the fusion zone (FZ) boundary and equiaxed dendrites at the center of FZ, with divorced eutectic β-Mg17Al12 particles, were observed. The FLW joints had smaller dendrite cell sizes with a narrower FZ than the DLW joints. The heat-affected zone consisted of recrystallized grains. Although the DLW joints fractured at the center of FZ and exhibited lower yield strength (YS), ultimate tensile strength (UTS), and fatigue strength, the FLW joints failed at the fusion boundary and displayed only moderate reduction in the YS, UTS, and fatigue strength with a joint efficiency of ~91 pct. After welding, the strain rate sensitivity basically vanished, and the DLW joints exhibited higher strain-hardening capacity. Stage III hardening occurred after yielding in both base metal (BM) and welded samples. Dimple-like ductile fracture characteristics appeared in the BM, whereas some cleavage-like flat facets together with dimples and river marking were observed in the welded samples. Fatigue crack initiated from the specimen surface or near-surface defects, and crack propagation was characterized by the formation of fatigue striations along with secondary cracks.

Fabrication of Al/Mg/Al Composites via Accumulative Roll Bonding and Their Mechanical Properties

PubMed Central

Nie, Jinfeng; Liu, Mingxing; Wang, Fang; Zhao, Yonghao; Li, Yusheng; Cao, Yang; Zhu, Yuntian

2016-01-01

Al(1060)/Mg(AZ31)/Al(1060) multilayered composite was successfully produced using an accumulative roll bonding (ARB) process for up to four cycles at an elevated temperature (400 °C). The microstructure evolution of the composites and the bonding characteristics at the interfaces between Al and Mg layers with increasing ARB cycles were characterized through optical microscopy, field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM). It was found that the grains of Al and Mg layers were significantly refined and Al3Mg2 and Al12 Mg17 intermetallic compound layers formed at the Al/Mg bonding interfaces. The strength increased gradually and the ultimate tensile strength (UTS) reached a maximum value of about 240 MPa at the third pass. Furthermore, the strengthening mechanism of the composite was analyzed based on the fracture morphologies. PMID:28774072

Causes of high O3 in the lower free troposphere over the Pacific Northwest as observed at the Mt. Bachelor Observatory

NASA Astrophysics Data System (ADS)

Ambrose, J. L.; Reidmiller, D. R.; Jaffe, D. A.

2011-09-01

We measured O3, CO, Hg, sub-micron particle scattering of mid-visible light (σsp), and water vapor (WV) at the Mt. Bachelor Observatory (MBO) in central Oregon, USA since 2004. The data were used to identify sources of large ozone enhancements in the lower free troposphere (FT). A total of 25 high-ozone events, defined as time periods when the 8-h averaged O3 mixing ratio was >70.0 ppbv, were recorded. The events occurred between early March and late September. For 18 of the 25 event days we were able to identify sources based on (1) relative enhancements of O3, CO, Hg and WV compared with the corresponding monthly distributions and (2) supporting data from the Hybrid Single-Particle Lagrangian Integrated Trajectory (HYSPLIT) model, the Navy Aerosol Analysis and Prediction System (NAAPS) global aerosol model, and Moderate Resolution Imaging Spectroradiometer (MODIS) satellite-derived active fire counts from the Fire Information for Resource Management System (FIRMS). Our analysis suggests that enhanced O3 levels during all the identified events were transported to MBO in the FT and were driven mostly by subsidence of O3-rich air masses from the upper troposphere/lower stratosphere (UT/LS), Asian long range transport (ALRT) and mixed ALRT + UT/LS influences. The UT/LS events were depleted in CO and total atmospheric mercury (TAM) compared to monthly median values. Levels of O3 and CO tended to be anti-correlated during UT/LS events, consistent with transport from clean regions in the UT. Conversely, the ALRT events were characterized by concomitant enhancements in CO and TAM with mean values during each event that were >70th percentile values for the months during which the events occurred. Unlike for UT/LS events, levels of O3 and CO during ALRT events tended to be correlated, consistent with photochemical O3 production in polluted air masses transported across the Pacific. The mixed ALRT + UT/LS events exhibited characteristics that were intermediate between those of the ALRT and UT/LS events. For the classifiable cases the fractional distribution of each event type was: UT/LS, ˜44% (n = 8); ALRT + UT/LS, ˜33% (n = 6); ALRT, ˜22% (n = 4). In terms of the total number of classifiable high-ozone event hours UT/LS, ALRT + UT/LS and ALRT events accounted for ˜52% (t = 85), ˜36% (t = 59) and ˜13% (t = 21), respectively. The results indicate that downward mixing of O3-rich air masses from the UT/LS together with trans-Pacific transport of urban/industrial and biomass burning emissions from the Asian continent are the most important mechanisms for delivering high O3 levels (i.e., 8-h averages >70.0 ppbv) to the lower FT in the Pacific Northwest.

Seasonal cycles of atmospheric methane and its carbon and hydrogen isotopic ratios in the lower and upper troposphere of the western Pacific region

NASA Astrophysics Data System (ADS)

Umezawa, T.; Aoki, S.; Nakazawa, T.; Machida, T.; Matsueda, H.; Sawa, Y.; Ishijima, K.; Patra, P. K.

2009-12-01

Although carbon and hydrogen isotopic ratios (δ13C and δD) of CH4 provide useful information about its sources and sinks, systematic measurements were quite limited. Tohoku University group and NIES group have conducted air-sampling programs by using commercial container ships sailing between Japan and New Zealand and by using commercial airliners flying between Australia and Japan, respectively. Using air samples collected by the programs, systematic measurements of δ13C and δD of atmospheric CH4 as well as CH4 concentration ([CH4]) have been made since 2006. Here, we report their spatial and temporal variations in the lower and upper troposphere (LT and UT). In the LT of the northern hemisphere (NH), the seasonal cycle of [CH4] showed the maximum in winter and the minimum in summer. δ13C varied seasonally almost negatively correlating with the [CH4], and the seasonality of δD showed much more significant negative correlation with the [CH4]. It was also found that CH4 sources with seasonally varying strength, such as wetlands with high emissions in late summer, play an important role in the atmospheric CH4 variations. In the tropics, a seasonally-dependent air exchange between the NH and the southern hemisphere (SH) was found to characterize the seasonal CH4 cycle. When the NH and SH air arrived, high and low [CH4] were observed, accompanied by low and high δ13C and δD values, respectively. In the LT of the SH, the seasonal maximum and minimum of the [CH4] appeared in austral winter and summer, respectively. The seasonal CH4 cycle was mainly ascribed to the seasonality in the CH4+OH reaction, but δ13C and δD showed rather complicated seasonality with larger amplitudes than expected from the CH4+OH reaction alone, suggesting additional contribution of a CH4+Cl reaction in the marine boundary layer. In the UT of the NH, the seasonal maximum and minimum of the [CH4] appeared in summer and winter-spring, respectively, with low and high values of δ13C and δD in corresponding seasons. The summertime high [CH4] was observed when the [CH4] showed the seasonal minimum in the LT. By examining the relationship between δ13C (or δD) and the [CH4], as well as the results of tagged tracer experiments using the CCSR/NIES/FRCGC AGCM-based chemical transport model, we found that biogenic CH4 emissions from India, Southeast Asia and China are responsible for such summertime high [CH4] in the UT. By comparing the latitudinal distributions of the annual average [CH4], δ13C and δD in the UT and LT, we found that [CH4] and δD in the NH were higher and lower in the LT than in the UT, respectively, while the situation was opposite in the SH, due to NH air intrusion through the UT. On the other hand, δ13C showed no different distributions in the LT and UT of the NH, while δ13C in the SH was higher in the LT than in the UT, probably due to the contribution of the CH4+Cl reaction in the marine boundary layer.

Improving nondestructive characterization of dual phase steels using data fusion

NASA Astrophysics Data System (ADS)

Kahrobaee, Saeed; Haghighi, Mehdi Salkhordeh; Akhlaghi, Iman Ahadi

2018-07-01

The aim of this paper is to introduce a novel methodology for nondestructive determination of microstructural and mechanical properties (due to the various heat treatments), as well as thickness variations (as a result of corrosion effect) of dual phase steels. The characterizations are based on the variations in the electromagnetic properties extracted from magnetic hysteresis loop and eddy current methods which are coupled with a data fusion system. This study was conducted on six groups of samples (with different thicknesses, from 1 mm to 4 mm) subjected to the various intercritical annealing processes to produce different fractions of martensite/ferrite phases and consequently, changes in hardness, yield strength and ultra tensile strength (UTS). This study proposes a novel soft computing technique to increase accuracy of nondestructive measurements and resolving overlapped NDE outputs related to the various samples. The empirical results indicate that applying the proposed data fusion technique on the two electromagnetic NDE data sets nondestructively, causes an increase in the accuracy and reliability of determining material features including ferrite fraction, hardness, yield strength, UTS, as well as thickness variations.

Aircraft Steels

DTIC Science & Technology

2009-02-19

component usage. PH 13-8Mo is a precipitation-hardenable martensitic stainless steel combining excellent corrosion resistance with strength. Custom 465 is...a martensitic , age-hardenable stainless steel capable of about 1,724 MPa (250 ksi) UTS when peak-aged (H900 condition). Especially, this steel can...NOTES 14. ABSTRACT Five high strength steels (4340, 300M, AerMet 100, Ferrium S53, and Hy-Tuf) and four stainless steels (High Nitrogen, 13

Modified ring stretch tensile testing of Zr-1Nb cladding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cohen, A.B.; Majumdar, S.; Ruther, W.E.

1998-03-01

In a round robin effort between the US Nuclear Regulatory Commission, Institut de Protection et de Surete Nucleaire in France, and the Russian Research Centre-Kurchatov Institute, Argonne National Laboratory conducted 16 modified ring stretch tensile tests on unirradiated samples of zr-1Nb cladding, which is used in Russian VVER reactors. Test were conducted at two temperatures (25 and 400 C) and two strain rates (0.001 and 1 s{sup {minus}1}). At 25 C and 0.001 s{sup {minus}1}, the yield strength (YS), ultimate tensile strength (UTS), uniform elongation (UE), and total elongation (TE) were 201 MPa, 331 MPa, 18.2%, and 57.6%, respectively. Atmore » 400 C and 0.001 s{sup {minus}1}, the YS, UTS, UE, and TE were 109 MPa, 185 MPa, 15.4%, and 67.7%, respectively. Finally, at 400 C and 1 s{sup {minus}1}, the YS, UTS, UE, and TE were 134 MPa, 189 MPa, 18.9%, and 53.4%, respectively. The high strain rate tests at room temperature were not successful. Test results proved to be very sensitive to the amount of lubrication used on the inserts; because of the large contact area between the inserts and specimen, too little lubrication leads to significantly higher strengths and lower elongations being reported. It is also important to note that only 70 to 80% of the elongation takes place in the gauge section, depending on specimen geometry. The appropriate percentage can be estimated from a simple model or can be calculated from finite-element analysis.« less

Causes of high O3 in the lower free troposphere over the Pacific Northwest as observed at the Mt. Bachelor Observatory

NASA Astrophysics Data System (ADS)

Ambrose, J. L.; Reidmiller, D.; Jaffe, D. A.

2011-12-01

We measured O3, CO, Hg, sub-micron particle scattering of mid-visible light (σsp), and water vapor (WV) at the Mt. Bachelor Observatory (MBO) in central Oregon, USA since 2004. The data were used to identify sources of large ozone enhancements in the lower free troposphere (FT) from 2004-2009. A total of 25 high-ozone events, defined as time periods when the 8-hr averaged O3 mixing ratio was >70.0 ppbv, were recorded. The events occurred between early March and late September. For 18 of the 25 event days we were able to identify sources based on (1) relative enhancements of O3, CO, Hg and WV compared with the corresponding monthly distributions and (2) supporting data from the Hybrid Single-Particle Lagrangian Integrated Trajectory (HYSPLIT) model, the Navy Aerosol Analysis and Prediction System (NAAPS) global aerosol model, and Moderate Resolution Imaging Spectroradiometer (MODIS) satellite-derived active fire counts from the Fire Information for Resource Management System (FIRMS). Our analysis suggests that enhanced O3 levels during all the identified events were transported to MBO in the FT and were driven mostly by subsidence of O3-rich air masses from the upper troposphere/lower stratosphere (UT/LS), Asian long range transport (ALRT) and mixed ALRT+UT/LS influences. The UT/LS events were depleted in CO and total atmospheric mercury (TAM) compared to monthly median values. Levels of O3 and CO tended to be anti-correlated during UT/LS events, consistent with transport from clean regions in the UT. Conversely, the ALRT events were characterized by concomitant enhancements in CO and TAM with mean values during each event that were >70th percentile values for the months during which the events occurred. Unlike for UT/LS events, levels of O3 and CO during ALRT events tended to be correlated, consistent with photochemical O3 production in polluted air masses transported across the Pacific. The mixed ALRT+UT/LS events exhibited characteristics that were intermediate between those of the ALRT and UT/LS events. For the classifiable cases the fractional distribution of each event type was: UT/LS, ~44% (n=8); ALRT+UT/LS, ~33% (n=6); ALRT, ~22% (n=4). In terms of the total number of classifiable high-ozone event hours UT/LS, ALRT+UT/LS and ALRT events accounted for ~52% (t=85), ~36% (t=59) and ~13% (t=21), respectively. The results indicate that downward mixing of O3-rich air masses from the UT/LS together with trans-Pacific transport of urban/industrial and biomass burning emissions from the Asian continent are the most important mechanisms for delivering high O3 levels (i.e., 8-hr averages >70.0 ppbv) to the lower FT in the Pacific Northwest. The high-ozone event characterization methodology developed from the 2004-2009 data set is further applied to observations made at MBO during 2010 and 2011.

Molecular Mechanisms of Urea Transport in Health and Disease

PubMed Central

Klein, Janet D.; Blount, Mitsi A.; Sands, Jeff M.

2012-01-01

In the late 1980s, urea permeability measurements produced values that could not be explained by paracellular transport or lipid phase diffusion. The existence of urea transport proteins were thus proposed and less than a decade later, the first urea transporter was cloned. The SLC14A family of urea transporters has two major subgroups, designated SLC14A1 (or UT-B) and Slc14A2 (or UT-A). UT-B and UT-A gene products are glycoproteins located in various extra-renal tissues however, a majority of the resulting isoforms are found in the kidney. The UT-B (Slc14A1) urea transporter was originally isolated from erythrocytes and two isoforms have been reported. In kidney, UT-B is located primarily in the descending vasa recta. The UT-A (Slc14A2) urea transporter yields 6 distinct isoforms, of which 3 are found chiefly in the kidney medulla. UT-A1 and UT-A3 are found in the inner medullary collecting duct (IMCD), while UT-A2 is located in the thin descending limb. These transporters are crucial to the kidney’s ability to concentrate urine. The regulation of urea transporter activity in the IMCD involves acute modification through phosphorylation and subsequent movement to the plasma membrane. UT-A1 and UT-A3 accumulate in the plasma membrane in response to stimulation by vasopressin or hypertonicity. Long term regulation of the urea transporters in the IMCD involves altering protein abundance in response to changes in hydration status, low protein diets, or adrenal steroids. Urea transporters have been studied using animal models of disease including diabetes mellitus, lithium intoxication, hypertension, and nephrotoxic drug responses. Exciting new genetically engineered mouse models are being developed to study these transporters. PMID:23007461

Molecular mechanisms of urea transport in health and disease.

PubMed

Klein, Janet D; Blount, Mitsi A; Sands, Jeff M

2012-12-01

In the late 1980s, urea permeability measurements produced values that could not be explained by paracellular transport or lipid phase diffusion. The existence of urea transport proteins were thus proposed and less than a decade later, the first urea transporter was cloned. The family of urea transporters has two major subgroups, designated SLC14A1 (or UT-B) and Slc14A2 (or UT-A). UT-B and UT-A gene products are glycoproteins located in various extra-renal tissues however, a majority of the resulting isoforms are found in the kidney. The UT-B (Slc14A1) urea transporter was originally isolated from erythrocytes and two isoforms have been reported. In kidney, UT-B is located primarily in the descending vasa recta. The UT-A (Slc14A2) urea transporter yields six distinct isoforms, of which three are found chiefly in the kidney medulla. UT-A1 and UT-A3 are found in the inner medullary collecting duct (IMCD), while UT-A2 is located in the thin descending limb. These transporters are crucial to the kidney's ability to concentrate urine. The regulation of urea transporter activity in the IMCD involves acute modification through phosphorylation and subsequent movement to the plasma membrane. UT-A1 and UT-A3 accumulate in the plasma membrane in response to stimulation by vasopressin or hypertonicity. Long-term regulation of the urea transporters in the IMCD involves altering protein abundance in response to changes in hydration status, low protein diets, or adrenal steroids. Urea transporters have been studied using animal models of disease including diabetes mellitus, lithium intoxication, hypertension, and nephrotoxic drug responses. Exciting new genetically engineered mouse models are being developed to study these transporters.

CPO Prediction: Accuracy Assessment and Impact on UT1 Intensive Results

NASA Technical Reports Server (NTRS)

Malkin, Zinovy

2010-01-01

The UT1 Intensive results heavily depend on the celestial pole offset (CPO) model used during data processing. Since accurate CPO values are available with a delay of two to four weeks, CPO predictions are necessarily applied to the UT1 Intensive data analysis, and errors in the predictions can influence the operational UT1 accuracy. In this paper we assess the real accuracy of CPO prediction using the actual IERS and PUL predictions made in 2007-2009. Also, results of operational processing were analyzed to investigate the actual impact of EOP prediction errors on the rapid UT1 results. It was found that the impact of CPO prediction errors is at a level of several microseconds, whereas the impact of the inaccuracy in the polar motion prediction may be about one order of magnitude larger for ultra-rapid UT1 results. The situation can be amended if the IERS Rapid solution will be updated more frequently.

POLAR-UVI and other Coordinated Observations of a Traveling Convection Vortex Event Observed on 24 July 1996

NASA Technical Reports Server (NTRS)

Clauer, C. R.; Baker, J. B.; Ridley, A. J.; Sitar, R. J.; Papitashvili, V. O.; Cumnock, J.; Spann, J. F., Jr.; Brittnacher, M. J.; Parks, G. K.

1997-01-01

Coordinated analysis of data from the POLAR UVI instrument, ground magnetometers, incoherent scatter radar, solar wind monitors IMP-8 and WIND, and DMSP satellite is focused on a traveling convection vortex (TCV) event on 24 July 1966. Starting at 10:48 UT, ground magnetometers in Greenland and eastern Canada measure pulsations consistent with the passing overhead of a series of alternating TCV field-aligned current pairs. Sondrestrom incoherent scatter radar measures strong modulation of the strength and direction of ionospheric plasma flow, The magnetometer pulsations grow in magnitude over the next hour, peaking in intensity at 11:39 UT, at which time the UVI instrument measures a localized intensification of auroral emissions over central and western Greenland. Subsequent images show the intensification grow in strength and propagate westward (tailward) until approximately 11:58 UT at which time the emissions fade. These observations are consistent with the westward passage of two pairs of moderately intense TCVs over central Greenland followed by a third very intense TCV pair. The intensification of auroral emissions at 11:39 UT is associated with the trailing vortex of the third TCV pair, thought to be the result of an upward field-aligned current. Measurements of the solar wind suggest that a pressure change may be responsible for triggering the first two pairs of TCVS, and that a subsequent sudden change in orientation of the IMF may have produced the intensification of the third TCV pair and the associated aurora] brightening. DMSP particle data indicate that the TCVs occur on field lines which map to the boundary plasma sheet or outer edge of the low latitude boundary layer.

Investigation of morphological, structural, and mechanical characteristics of Zircaloy-4 irradiated with 3.5 MeV hydrogen ions beam

NASA Astrophysics Data System (ADS)

Rafique, Mohsin; Butt, M. Z.; Ahmad, Sajjad

2017-09-01

Zircaloy-4 specimens were irradiated with 3.5 MeV hydrogen ions (dose range: 1  ×  1013 H+1 cm-2 to 1  ×  1015 H+1 cm-2) using a Pelletron accelerator. FESEM studies reveal formation of hydrogen micro-bubbles, bubbles induced blisters of irregular shapes, and development of cracks on the specimen surface, as in the case of pure zirconium. However, for the highest irradiation dose of 1  ×  1015 H+1 cm-2, agglomeration of flower-shape blisters is observed. XRD analysis shows that the most preferentially oriented crystallographic plane is (0 0 4) with texture coefficient values 1.832-2.308 depending on the ions dose. Its diffraction peak intensity first decreases with the increase in ions dose up to 5  ×  1013 H+1 cm-2 and later increases up to 1  ×  1015 H+1 cm-2. Opposite is found in case of diffraction peak width. Crystallite size and lattice strain determined by Williamson-Hall analysis display a linear relationship between the two with positive slope. Mechanical strength, namely yield stress (YS), ultimate tensile strength (UTS), and fracture stress (FS), increases sharply with ions dose up to 5  ×  1013 H+1 cm-2. For 1  ×  1014 H+1 cm-2 dose there is a sudden drop of stress to a lowest value and then a slow steady increase in stress up to the highest dose 1  ×  1015 H+1 cm-2. Same pattern is followed by uniform elongation and total elongation. All three stress parameters YS, UTS, and FS follow Inverse Hall-Petch relation.

Effect of hot-dip galvanizing processes on the microstructure and mechanical properties of 600-MPa hot-dip galvanized dual-phase steel

NASA Astrophysics Data System (ADS)

Kuang, Chun-fu; Zheng, Zhi-wang; Wang, Min-li; Xu, Quan; Zhang, Shen-gen

2017-12-01

A C-Mn dual-phase steel was soaked at 800°C for 90 s and then either rapidly cooled to 450°C and held for 30 s (process A) or rapidly cooled to 350°C and then reheated to 450°C (process B) to simulate the hot-dip galvanizing process. The influence of the hot-dip galvanizing process on the microstructure and mechanical properties of 600-MPa hot-dip galvanized dual-phase steel (DP600) was investigated using optical microscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and tensile tests. The results showed that, in the case of process A, the microstructure of DP600 was composed of ferrite, martensite, and a small amount of bainite. The granular bainite was formed in the hot-dip galvanizing stage, and martensite islands were formed in the final cooling stage after hot-dip galvanizing. By contrast, in the case of process B, the microstructure of the DP600 was composed of ferrite, martensite, bainite, and cementite. In addition, compared with the yield strength (YS) of the DP600 annealed by process A, that for the DP600 annealed by process B increased by approximately 50 MPa because of the tempering of the martensite formed during rapid cooling. The work-hardening coefficient ( n value) of the DP600 steel annealed by process B clearly decreased because the increase of the YS affected the computation result for the n value. However, the ultimate tensile strength (UTS) and elongation ( A 80) of the DP600 annealed by process B exhibited less variation compared with those of the DP600 annealed by process A. Therefore, DP600 with excellent comprehensive mechanical properties (YS = 362 MPa, UTS = 638 MPa, A 80 = 24.3%, n = 0.17) was obtained via process A.

Microstructure and properties of ultrafine grained structure of Cu-Zn-Si alloy fabricated by heavy cold rolling

NASA Astrophysics Data System (ADS)

Miura, H.; Kobayashi, T.; Kobayashi, M.

2014-08-01

Cu-18.2Zn-1.5Si-0.25Fe (mass%) alloy was heavily cold rolled. Ultrafine grained (UFGed) structure, containing a mixture of lamellar and mechanical twins, was easily and homogeneously formed. The average grain size was approximately 100 nm. The as-rolled sample showed quite high ultimate tensile strength (UTS) over 1 GPa. The UTS was higher than those obtained by multi directional forging. When the samples were annealed at relatively low temperatures between 553 K and 653 K, they showed slight hardening followed by large softening due to occurrence of static recrystallization (SRX). Annealing of UFGed structure at relatively low temperature of around 0.4 Tm caused extensive SRX that, in turn, induces ultrafine RXed grained structure. The grain size of the RXed sample was as fine as 200 nm. Although the annealing induced recovery of ductility while UTS gradually reduces, UTS over 1 GPa with ductility of 15 % were attained. The RXed grains mainly contained ultrafine annealing twins. Therefore, UFGed structure and superior mechanical properties could be achieved by a simple process of cold rolling, i.e., without severe plastic deformation.

Nitrogen oxides and ozone in the tropopause region of the Northern Hemisphere: Measurements from commercial aircraft in 1995/1996 and 1997

NASA Astrophysics Data System (ADS)

Brunner, Dominik; Staehelin, Johannes; Jeker, Dominique; Wernli, Heini; Schumann, Ulrich

2001-11-01

Measurements of nitrogen oxides (NO and NO2) and ozone (O3) were performed from a Swissair B-747 passenger aircraft in two extended time periods (May 1995 to May 1996, August to November 1997) in the framework of the Swiss NOXAR and the European POLINAT 2 project. The measurements were obtained on a total of 623 flights between Europe and destinations in the United States and the Far East. NO2 measurements were obtained only after December 1995 and were less precise than the NO measurements. Therefore daytime NO2 values were derived from measured NO and O3 concentrations assuming photostationary equilibrium. The completed NOx data set (measured NO, measured NO2 during night, and calculated NO2 during day) includes a complete annual cycle and is the most extensive and representative data set currently available for the upper troposphere (UT) and the lower stratosphere (LS) covering a significant proportion of the northern hemisphere between 15°N and 65°N. NOx concentrations in midlatitudes (30°-60°N) showed a marked seasonal variation both in the UT and the LS with a maximum in summer (median/mean values of 159/264 pptv in UT, 199/237 pptv in LS) and a minimum in winter (51/99 pptv in UT, 67/91 pptv in LS). Mean NOx concentrations were generally much higher than the respective median values, in particular in the UT, which reflects the important contribution from comparatively few very high concentrations observed in large-scale convection/lightning and small-scale aircraft plumes. Seasonal mean NOx concentrations in the UT were up to 3-4 times higher over continental regions than over the North Atlantic during summer. Lightning production of NO and convective vertical transport from the polluted boundary layer thus appear to have dominated the upper tropospheric NOx budget over these continental regions, particularly during summer. Ozone concentrations at aircraft cruising levels typically varied by an order of magnitude due to the strong vertical gradient in the LS. Seasonal mean values were dominated by large-scale dynamical processes controlling the altitude of the tropopause and the O3 abundance in the LS. O3 in the UT in midlatitudes showed a broad maximum between June and August, typical of observations in the free troposphere.

Biocompatibility and bond degradation of poly-acrylic acid coated copper iodide-adhesives.

PubMed

ALGhanem, Adi; Fernandes, Gabriela; Visser, Michelle; Dziak, Rosemary; Renné, Walter G; Sabatini, Camila

2017-09-01

To investigate the effect of poly-acrylic acid (PAA) copper iodide (CuI) adhesives on bond degradation, tensile strength, and biocompatibility. PAA-CuI particles were incorporated into Optibond XTR, Optibond Solo and XP Bond in 0.1 and 0.5mg/ml. Clearfil SE Protect, an MDPB-containing adhesive, was used as control. The adhesives were applied to human dentin, polymerized and restored with composite in 2mm-increments. Resin-dentin beams (0.9±0.1mm 2 ) were evaluated for micro-tensile bond strength after 24h, 6 months and 1year. Hourglass specimens (10×2×1mm) were evaluated for ultimate tensile strength (UTS). Cell metabolic function of human gingival fibroblast cells exposed to adhesive discs (8×1mm) was assessed with MTT assay. Copper release from adhesive discs (5×1mm) was evaluated with UV-vis spectrophotometer after immersion in 0.9% NaCl for 1, 3, 5, 7, 10, 14, 21 and 30 days. SEM, EDX and XRF were conducted for microstructure characterization. XTR and Solo did not show degradation when modified with PAA-CuI regardless of the concentration. The UTS for adhesives containing PAA-CuI remained unaltered relative to the controls. The percent viable cells were reduced for Solo 0.5mg/ml and XP 0.1 or 0.5mg/ml PAA-CuI. XP demonstrated the highest ion release. For all groups, the highest release was observed at days 1 and 14. PAA-CuI particles prevented the bond degradation of XTR and Solo after 1year without an effect on the UTS for any adhesive. Cell viability was affected for some adhesives. A similar pattern of copper release was demonstrated for all adhesives. Copyright © 2017. Published by Elsevier Ltd.

Structural, mechanical and light yield characterisation of heat treated LYSO:Ce single crystals for medical imaging applications

NASA Astrophysics Data System (ADS)

Mengucci, P.; André, G.; Auffray, E.; Barucca, G.; Cecchi, C.; Chipaux, R.; Cousson, A.; Davì, F.; Di Vara, N.; Rinaldi, D.; Santecchia, E.

2015-06-01

Five single crystals of cerium-doped lutetium yttrium oxyorthosilicate (LYSO:Ce) grown by the Czochralski method were submitted to structural characterisation by X-ray (XRD) and neutron (ND) diffraction, scanning (SEM) and transmission (TEM) electron microscopy and energy dispersive microanalysis (EDS). The Ultimate Tensile Strength (UTS), the Young Modulus (YM) and the Light Yield (LY) of the samples were also measured in order to correlate the mechanical and the optical behaviour of the crystals with the characteristics of their microstructure. Two of the samples analysed were also heat treated at 300 °C for 10 h to evidence possible variations induced by the temperature in the optical and mechanical response of the crystals. Results showed that the mean compositional variations evidenced by the structural analyses do not affect the mechanical and optical behaviour of the samples. On the contrary, the thermal treatment could induce the formation of coherent spherical particles (size 10 to 15 nm), not uniformly distributed inside the sample, that strongly reduce the UTS and YM values, but it does not affect the optical response of the crystal. This latter result was attributed to the low value of the heating temperature (300 °C) that is not sufficiently high to induce annealing of the oxygen vacancies traps that are responsible of the deterioration of the scintillation properties of the LYSO:Ce crystals. This study was carried out in the framework of the Crystal Clear Collaboration (CCC).

Structure and mechanical characterization of Mg-Nd-Zn alloys prepared by different processes

NASA Astrophysics Data System (ADS)

Dvorský, D.; Kubásek, J.; Vojtěch, D.; Voňavková, I.; Veselý, M.; Čavojský, M.

2017-02-01

Magnesium alloys containing about 3 wt. % of Nd and 0.5 wt. % of Zn are considered as promising materials for application in transport and medical industry. Properly treated materials can reach ultimate tensile strength (UTS) higher than 300 MPa. Also the corrosion resistance of these alloys is superior to many other magnesium-based materials. Present work is focused on the preparation of Mg-3Nd-0.5Zn magnesium alloy by classical casting and subsequent thermal treatment. As-cast material was extruded at 400 °C, with extrusion ratio equal to 16 and velocity of 0.2 mm/s. The effect of thermal treatment and also strong plastic deformation during extrusion on final structure conditions and mechanical properties is specified. Present results confirm significant improvement of tensile yield strength (TYS) and UTS after extrusion process as a consequence of fine-grained structure combined with precipitation strengthening. Beside, texture strengthening in the direction parallel to the extrusion has been observed too.

Uterine artery flow velocity waveform, arterial flow indices, follicular dynamics, and sex hormones during preovulatory period in synchronized ovulatory cycle of Bos indicus beef cows.

PubMed

Moonmanee, Tossapol; Navanukraw, Chainarong; Yama, Punnawut; Jitjumnong, Jakree

2018-03-01

A greater understanding of the uterine artery's (UtA) biology is essential to the increase in female reproductive abilities. The UtA flow velocity waveform, blood flow volume (BFV), pulsatility and resistance indices (PI and RI), blood flow velocities, dynamics of the dominant follicle (DF), and estradiol (E2) and progesterone (P4) levels in an induced ovulatory cycle were evaluated in Thai native cattle. Twenty cows were induced with synchronized ovulation through a P4-releasing device, from Day -9 to Day -4, concurrent with the administration of two doses of a gonadotropin-releasing hormone on Day -9 and Day -1, and two doses of prostaglandin F 2α on Day -4 and 8 h later. Day 0 was designated as the day of ovulation. The cows underwent Doppler sonographic determination and blood collection from Day -4 to Day 0. The cows were classified in the non-ovulating (n = 5) and ovulating groups (n = 15). The ovulating cows presented higher BFV values, blood flow velocities, DF growth rates, and E2 levels; yet lower PI values and P4 concentrations, than those of the non-ovulating cows. The BFV values and the blood flow velocities were greater, but the RI and PI values were lower in the ovulatory side UtA than in the contraovulatory side UtA. The BFV values were positively correlated with blood flow velocities, DF growth rates and E2 concentrations in the ovulating cows; confirming the importance of UtA blood flow, follicular growth, and E2-vasodilation during preovulatory phase in the induced ovulatory cycle of Bos indicus beef cows. Copyright © 2018 Society for Biology of Reproduction & the Institute of Animal Reproduction and Food Research of Polish Academy of Sciences in Olsztyn. Published by Elsevier B.V. All rights reserved.

The study of variability of TEC over mid-latitude American regions during the ascending phase of solar cycle 24 (2009-2011)

NASA Astrophysics Data System (ADS)

Asmare Tariku, Yekoye

2016-08-01

This paper deals with the pattern of the variability of the Global Positioning System vertical total electron content (GPS VTEC) and the modeled vertical total electron content (IRI 2012 TEC) over American mid-latitude regions during the rising phase of solar cycle 24 (2009-2011). This has been conducted employing ground-based dual frequency GPS receiver installed at Mississippi County Airport (geographic lat. 36.85°N and long. 270.64°E). In this work, the monthly and seasonal variations in the measured VTEC have been analyzed and compared with the VTEC inferred from IRI-2012 model. It has been shown that the monthly and seasonal mean VTEC values get decreased mostly between 05:00 and 10:00 UT and reach their minimal nearly at around 10:00 UT for both the experimental and the model. The VTEC values then get increased and reach the peak values at around 20:00 UT and decrease again. Moreover, it is depicted that the model better estimates both the monthly and seasonal mean hourly VTEC values mostly between 15:00 and 20:00 UT. The modeled monthly and seasonal VTEC values are smaller than the corresponding measured values as the solar activity decreases when all options for the topside electron density are used. However, as the Sun goes from a very low to a high solar activity, the overestimation performance of the VTEC values derived from the model increases. The overall results show that it is generally better to use the model with IRI-2000 option for the topside electron density in estimating the monthly and seasonal VTEC variations, especially when the activity of the Sun decreases.

A comparison of three different physiotherapy modalities used in the physiotherapy of burns.

PubMed

Sar, Zübeyir; Polat, Mine Gülden; Özgül, Bahar; Aydoğdu, Onur; Camcoğlu, Burcu; Acar, Ahmet Hakan; Yurdalan, Saadet Ufuk

2013-01-01

The present study compared the effectiveness of matrix rhythm therapy, ultrasound treatment (UT), laser treatment (LT) used in the physiotherapy of burns. The study was conducted at the Wound and Burn Healing Center, Dr. Lütfi Kırdar Kartal Education and Research Hospital (Turkey) from June 2009 to January 2012. The case series comprised 39 individuals with second- and third-degree upper-limb burns, whose burn traumas ended approximately 1 to 3 months previously. Participants were separated into three groups: matrix rhythm treatment (MRT), UT and LT; each group was also applied a treatment protocol including whirlpool and exercise. Pain, range of motion (ROM), muscular strength, skin elasticity, and sensory functions were evaluated before and after the treatment. Pressure sense and passive ROM were higher in the MRT group than in the LT group (P < .05). Pain was lower in the LT group than in the UT group, and passive ROM was higher in the UT group than the in LT group (P < .05). Active ROM was found to increase in all treatment groups, whereas passive ROM increased only in the MRT and UT groups; pressure sense increased only in the MRT group, and pain decreased only in the LT group (P < .05). MRT was found to be more effective in the restoration of sensory functions than LT, whereas LT was more effective in reducing pain than UT. No significant difference was observed in terms of skin elasticity according to the results of three treatment modalities. It is suggested that further research with more cases should be conducted to examine the long-term effect of treatment modalities.

Peripheral markers of central fatigue in trained and untrained during uncompensable heat stress.

PubMed

Wright, Heather E; Selkirk, Glen A; Rhind, Shawn G; McLellan, Tom M

2012-03-01

The development of fatigue is more pronounced in the heat than thermoneutral environments; however, it is unclear whether biomarkers of central fatigue are consistent with the higher core temperature (T (c)) tolerated by endurance trained (TR) versus untrained (UT) during exertional heat stress (EHS). The purpose of this study was to examine the indicators of central fatigue during EHS in TR versus UT. Twelve TR and 11 UT males (mean ± SE [Formula: see text] = 70 ± 2 and 50 ± 1 mL kg LBM(-1) min(-1), respectively) walked on a treadmill to exhaustion (EXH) in 40°C (dry) wearing protective clothing. Venous blood was obtained at PRE and 0.5°C T (c) increments from 38 to 40°C/EXH. Free tryptophan (f-TRP) decreased dramatically at 39.5°C for the TR. Branch chain amino acids decreased with T (c) and were greater for UT than TR at EXH. Tyrosine and phenylalanine remained unchanged. Serum S100β was undetectable (<5 pg mL(-1)). Albumin was greater for the UT from PRE to 39.0°C and at EXH. Prolactin (PRL) responded to relative thermal strain with similar EXH values despite higher T (c) tolerated for TR (39.7 ± 0.09°C) than UT (39.0 ± 0.09°C). The high EXH PRL values for both groups support its use as a biomarker of the serotonin and dopamine interplay within the brain during the development of central fatigue.

High-rate tensile properties of Si-reduced TRIP sheet steels

NASA Astrophysics Data System (ADS)

Choi, Ildong; Park, Yeongdo; Son, Dongmin; Kim, Sung-Joon; Moon, Manbeen

2010-02-01

There have been efforts to develop Si-reduced TRIP steels to improve the wettability of Zn coatings, since the conventional CMnSi-TRIP steels suffer from poor galvanizability. In addition, for the development of potential applications of Si-reduced TRIP steels in vehicle crash management, a better understanding of high strain rate properties is required. In the present study, the effects of alloying elements, such as Cu, Al, Si, and P, on the high-rate tensile properties of Si-reduced TRIP sheet steels were investigated. Tensile tests were performed with a servo-hydraulic tensile testing machine at strain rates ranging from 10-2 to 6 × 102 s-1, and the ultimate tensile strength, elongation, strain rate sensitivity, and absorbed energy were evaluated. The retained austenite volume fractions and carbon content of the specimens were measured using neutron diffraction. The UTS was increased with Cu, Al, Si, and P alloying throughout the strain rate range, and the alloying effect on UTS was considerable with Cu and P. The effects of alloying on the microstructure were not significant. All the steels tested in this study exhibited positive strain rate sensitivity, and the m value at strain rates higher than 10 s-1 was at least two times higher than that at lower strain rates.

On the Logical Development of Statistical Models.

DTIC Science & Technology

1983-12-01

David Steinberg, and Jean Wallis for their helpful cosments to a preliminary draft of this work. -21- REFERENCES [1] Anscombe, F. J. and Tukey, J. W ...effect of a known vector x of predictor variables. In this way we obtain an explicative-static or type 11 model and -3- W .- r󈧬 41 U) 3 0) H + N 1 0...dependency is: Yt M it + ut p(ut ) - U It P(ut M-t) - I - t (2.1) t W P01 + Vt-1(P11 - P0 1) where Yt can only have the values zero and one, p is its

Transport characteristics of urea transporter-B.

PubMed

Yang, Baoxue

2014-01-01

UT-B represents the major urea transporter in erythrocytes, in addition to being expressed in kidney descending vasa recta, brain, spleen, ureter, bladder, and testis. Expression of urea transporter UT-B confers high urea permeability to mammalian erythrocytes. Erythrocyte membranes are also permeable to various urea analogues, suggesting common transport pathways for urea and structurally similar solutes. UT-B is highly permeable to urea and the chemical analogues formamide, acetamide, methylurea, methylformamide, ammonium carbamate, and acrylamide, each with a Ps > 5.0 × 10(-6) cm/s at 10 °C. The amides formamide, acetamide, acrylamide, and butyramide efficiently diffuse across lipid bilayers. The urea analogues dimethylurea, acryalmide, methylurea, thiourea, and methylformamide inhibit UT-B-mediated urea transport by >60 % by a pore-blocking mechanism. UT-B is also a water channel in erythrocytes and has a single-channel water permeability that is similar to aquaporin-1. Whether UT-B is an NH3 channel still needs further study. Urea permeability (Purea) in erythrocytes differs between different mammals. Carnivores (dog, fox, cat) exhibit high Purea. In contrast, herbivores (cow, donkey, sheep) show much lower Purea. Erythrocyte Purea in human and pig (omnivores) was intermediate. Rodents and lagomorphs (mouse, rat, rabbit) have Purea intermediate between carnivores and omnivores. Birds that do not excrete urea and do not express UT-B in their erythrocytes have very low values. In contrast to Purea, water permeability is relatively similar in all mammals studied. This chapter will provide information about the transporter characteristics of UT-B.

Ionospheric redistribution during geomagnetic storms

PubMed Central

Immel, T J; Mannucci, A J

2013-01-01

[1]The abundance of plasma in the daytime ionosphere is often seen to grow greatly during geomagnetic storms. Recent reports suggest that the magnitude of the plasma density enhancement depends on the UT of storm onset. This possibility is investigated over a 7year period using global maps of ionospheric total electron content (TEC) produced at the Jet Propulsion Laboratory. The analysis confirms that the American sector exhibits, on average, larger storm time enhancement in ionospheric plasma content, up to 50% in the afternoon middle-latitude region and 30% in the vicinity of the high-latitude auroral cusp, with largest effect in the Southern Hemisphere. We investigate whether this effect is related to the magnitude of the causative magnetic storms. Using the same advanced Dst index employed to sort the TEC maps into quiet and active (Dst<−100 nT) sets, we find variation in storm strength that corresponds closely to the TEC variation but follows it by 3–6h. For this and other reasons detailed in this report, we conclude that the UT-dependent peak in storm time TEC is likely not related to the magnitude of external storm time forcing but more likely attributable to phenomena such as the low magnetic field in the South American region. The large Dst variation suggests a possible system-level effect of the observed variation in ionospheric storm response on the measured strength of the terrestrial ring current, possibly connected through UT-dependent modulation of ion outflow. PMID:26167429

Ionospheric redistribution during geomagnetic storms.

PubMed

Immel, T J; Mannucci, A J

2013-12-01

[1]The abundance of plasma in the daytime ionosphere is often seen to grow greatly during geomagnetic storms. Recent reports suggest that the magnitude of the plasma density enhancement depends on the UT of storm onset. This possibility is investigated over a 7year period using global maps of ionospheric total electron content (TEC) produced at the Jet Propulsion Laboratory. The analysis confirms that the American sector exhibits, on average, larger storm time enhancement in ionospheric plasma content, up to 50% in the afternoon middle-latitude region and 30% in the vicinity of the high-latitude auroral cusp, with largest effect in the Southern Hemisphere. We investigate whether this effect is related to the magnitude of the causative magnetic storms. Using the same advanced Dst index employed to sort the TEC maps into quiet and active ( D s t <-100 nT) sets, we find variation in storm strength that corresponds closely to the TEC variation but follows it by 3-6h. For this and other reasons detailed in this report, we conclude that the UT-dependent peak in storm time TEC is likely not related to the magnitude of external storm time forcing but more likely attributable to phenomena such as the low magnetic field in the South American region. The large Dst variation suggests a possible system-level effect of the observed variation in ionospheric storm response on the measured strength of the terrestrial ring current, possibly connected through UT-dependent modulation of ion outflow.

Textural and biochemical properties of cobia (Rachycentron canadum) sashimi tenderised with the ultrasonic water bath.

PubMed

Chang, Hung-Chia; Wong, Ren-Xian

2012-06-01

The present study investigated the tenderisation effects ultrasound processing (UT) on farmed cobia sashimi. Age-treated cobia trunk muscles (AT) were used as the control. The pH, total volatile base nitrogen, trimethylamine nitrogen, thiobarbituric acid reactive substances, ATP catabolism components, K 1 value, and texture were evaluated. The texture of AT sashimi reached the optimal firmness range with 8.53N at day 7. However, AT samples could not be served raw after day 7 because of their poor freshness indexes, including a TVBN value of 18.53g/100g, a TMAN value of 3.25mg/100g, and a TBARS value 0.983MDAmg/100g. Moreover, the K 1 value of AT sashimi was 20.21% at day 5. UT was employed to efficiently tenderise cobia sashimi with an initial firmness of 9.70-7.82N after 90min of treatment. The results of this study indicate that UT accelerates the biochemical reaction rate, as evidenced by the increases in the TVBN, TMAN, and TBARS contents; however, these values were very low. The results of this study could provide basic information for the development of a novel ultrasonic tenderisation technique in raw seafood designed for restaurants and consumers. Copyright © 2011 Elsevier Ltd. All rights reserved.

Bond strength of etch-and-rinse and self-etch adhesive systems to enamel and dentin irradiated with a novel CO2 9.3 μm short-pulsed laser for dental restorative procedures.

PubMed

Rechmann, Peter; Bartolome, N; Kinsel, R; Vaderhobli, R; Rechmann, B M T

2017-12-01

The objective of this study was to evaluate the influence of CO 2 9.3 μm short-pulsed laser irradiation on the shear bond strength of composite resin to enamel and dentin. Two hundred enamel and 210 dentin samples were irradiated with a 9.3 µm carbon dioxide laser (Solea, Convergent Dental, Inc., Natick, MA) with energies which either enhanced caries resistance or were effective for ablation. OptiBond Solo Plus [OptiBondTE] (Kerr Corporation, Orange, CA) and Peak Universal Bond light-cured adhesive [PeakTE] (Ultradent Products, South Jordan, UT) were used. In addition, Scotchbond Universal [ScotchbondSE] (3M ESPE, St. Paul, MN) and Peak SE self-etching primer with Peak Universal Bond light-cured adhesive [PeakSE] (Ultradent Products) were tested. Clearfil APX (Kuraray, New York, NY) was bonded to the samples. After 24 h, a single plane shear bond test was performed. Using the caries preventive setting on enamel resulted in increased shear bond strength for all bonding agents except for self-etch PeakSE. The highest overall bond strength was seen with PeakTE (41.29 ± 6.04 MPa). Etch-and-rinse systems achieved higher bond strength values to ablated enamel than the self-etch systems did. PeakTE showed the highest shear bond strength with 35.22 ± 4.40 MPa. OptiBondTE reached 93.8% of its control value. The self-etch system PeakSE presented significantly lower bond strength. The shear bond strength to dentin ranged between 19.15 ± 3.49 MPa for OptiBondTE and 43.94 ± 6.47 MPa for PeakSE. Etch-and-rinse systems had consistently higher bond strength to CO 2 9.3 µm laser-ablated enamel. Using the maximum recommended energy for dentin ablation, the self-etch system PeakSE reached the highest bond strength (43.9 ± 6.5 MPa).

Engaging with Clients and Personalising Services at UTS Library: Measuring the Value for Libraries and Their Clients

ERIC Educational Resources Information Center

Tiffen, Belinda; England, Ashley

2011-01-01

Libraries have found themselves overtaken by commercial entities providing open, unmediated information services, causing debate about the future of libraries. It has been argued that in order to stay relevant, libraries must undertake a fundamental shift towards a new focus on engaging with clients. At University of Technology, Sydney (UTS)…

Explosive Chromospheric Evaporation and Warm Rain in a GOES C3 Flare Observed by IRIS, Hinode/EIS, and RHESSI

NASA Astrophysics Data System (ADS)

Brosius, J. W.; Inglis, A. R.

2017-12-01

IRIS and Hinode/EIS observed a C3.1 flare in AR 12002 in stare mode on 2014 March 15.GOES observed the flare to start at 00:21:35 UT and peak at 00:26:30 UT. The IRIS slitwas pointed near the center of the flare while the EIS slit was pointed 35 arcsec westof the IRIS slit. About 4 minutes before the GOES flare start, the C II and Si IV lineintensities observed by IRIS became (and remained) significantly greater than theirpre-flare average values; this indicates that the flare had begun and that thechromosphere and transition region were involved. IRIS first detected significant,blueshifted Fe XXI emission at 00:22:42 UT, by which time the C II and Si IV lineintensities had increased by factors around 100 and their profiles were significantlyredshifted. This combination of simultaneous, cospatial blueshifted Fe XXI emissionwith redshifted C II and Si IV emission indicates explosive chromospheric evaporation.SDO's HMI observed a localized area of enhanced magnetic field strength toward thesouthernmost portion of the EIS slit's position that appears to be connected to theflare site by faint loops evident in AIA 131 A emission. EIS spectra at this locationreveal intensity enhancements by factors up to about 1.7 in the Fe XIV and Fe XVI lineemission, and the emergence of faint Fe XXIII emission that is too weak to measurevelocities. Emission lines from the two coronal ions show redshifts of about 9 km/saround 00:24:00 UT. The density sensitive line intensity ratio of Fe XIV 264.7/274.2observed by EIS reveals an increase of electron density from (1.03+/-0.20)X10^9 /cm^3before the flare to (3.58+/-0.68)X10^9 /cm^3 during the flare. This combination ofredshifted coronal line emission and increased coronal electron density is consistentwith explosively evaporated flare material observed by IRIS falling as warm rain andaccumulating in the remote area observed by EIS. A thermal/nonthermal fit to the hardX-ray spectrum observed by RHESSI yields a nonthermal energy injection rate of4.9X10^26 ergs/s; combining this with an estimated injection area of (2.1+/-1.7)X10^17cm^2 based on IRIS slit-jaw images, we estimate a HXR beam energy flux of(6.7+/-5.5)X10^9 ergs/cm^2/s, a wide range whose larger values are consistent withexplosive chromospheric evaporation.

Elevated temperature tensile and creep behavior of a SiC fiber-reinforced titanium metal matrix composite. Final Report, 22 Dec. 1994 M.S. Thesis, 7 May 1993

NASA Technical Reports Server (NTRS)

Thurston, Rita J.

1995-01-01

In this research program, the tensile properties and creep behavior in air of (0)(sub 4), (0/90)(sub s) and (90)(sub 4) SCS-9/Beta 21S composite layups with 0.24 volume fraction fiber were evaluated. Monotonic tensile tests at 23, 482, 650 and 815 C yielded the temperature dependence of the elastic modulus, proportional limit, ultimate tensile strength and total strain at failure. At 650 C, the UTS of the (0)(sub 4) and (0/90)(sub s) layups decreases by almost 50 percent from the room temperature values, indicating that operating temperatures should be less than 650 C to take advantage of the specific tensile properties of these composites.

The Microstructure and Tensile Properties of a Newly Developed Mg-Al/Mg3Sb2 In Situ Composite in As-Cast and Extruded Conditions

NASA Astrophysics Data System (ADS)

Montajabnia, A.; Pourbahari, B.; Emamy, M.

2018-04-01

The microstructures and tensile properties of Mg-x wt%Al-y wt%Sb alloys have been studied where x/y ratio was 1 and Sb(Al) contents were 5, 10, 15 and 20 wt%, respectively. The results indicated that by increasing Sb(Al) content, not only the crystals of primary Mg3Sb2 alter from small flake-like particles to polygonal or needle-like morphology, but also the eutectic structure changes from semi-continuous network in Mg-5Al-5Sb to continuous network in Mg-20Sb-20Al alloy. The results obtained from thermal analysis revealed different peaks related to the formation of Mg3Sb2 as primary phase and eutectic structure containing Mg17Al12 + Al3Mg2 intermetallic phases. Further results also revealed that Sb(Al) additions change the solidification performance of the material by depressing the Mg3Sb2 nucleation temperature, reducing solidification range and widening eutectic area. Tensile testing results showed that with the increase in Sb (Al) content, ultimate tensile strength (UTS) and elongation values of the alloys are decreased in as-cast condition. But, significant improvement in the UTS and elongation values of the extruded specimens was attributed to the severe fragmentation of intermetallic phases and well distributed fine particles in the matrix which provided proper obstacles for dislocation motion. It was interesting to note that the fracture behavior of intermetallic particles was found to be different, while Mg3Sb2 was ductile, intermetallic compounds in eutectic regions were brittle.

High Static Stability in the Mixed Layer Above the Extratropical Tropopause

NASA Astrophysics Data System (ADS)

Kunz, A.; Konopka, P.; Müller, R.; Schiller, C.

2008-12-01

A strong relationship between the static stability N2 and the strength of mixing in the mixed layer above the extratropical tropopause is evident from in-situ data observed during the SPURT aircraft campaigns. We present a method for quantifying the strength of mixing from O3/CO tracer correlations and we find that N2 is positively correlated with the strength of mixing. Age of air simulations with the CLaMS model reveal two different types of mixed regions. One type consisting of older airmasses with higher values of N2 which are created by radiative adjustment after a mixing event. These airmasses are within the TIL (Tropopause Inversion Layer), considering the TIL as part of the mixing layer. The second type comprises younger airmasses with somehow lower stratospheric N2 values within the mixing layer, because of recent intrusion processes due to the permeability or so-called mid-latitude-breaks associated with the jet stream. With the help of radiative transfer calculations we simulate the influence of trace gases such as O3 and H2O on the temperature gradient and thus on the static stability above the tropopause in the idealized case of non-mixing (L-shape) O3 and H2O profiles and in the reference case of mixed profiles. Within the altitude range of the SPURT campaigns the mean vertical SPURT profiles are used as reference, which are fitted to the HALOE climatological profiles above the UT/LS.

Maternal serum homocysteine and uterine artery Doppler as predictors of preeclampsia and poor placentation.

PubMed

Maged, Ahmed M; Saad, Hany; Meshaal, Hadeer; Salah, Emad; Abdelaziz, Suzy; Omran, Eman; Deeb, Wesam S; Katta, Maha

2017-09-01

The aim of this study was to evaluate the role of maternal serum total Homocysteine (tHcy) and uterine artery (Ut-A) Doppler as predictors of preeclampsia (PE), intrauterine growth restriction (IUGR), and other complications related to poor placentation. A prospective cohort study was conducted on 500 women with spontaneous pregnancies. tHcy was measured at 15-19 weeks, and then, Ut-A Doppler was performed at 18-22 weeks of pregnancy. 453 pregnant women completed the follow-up of the study. The tHcy and Ut-A resistance index were significantly higher in women who developed PE, IUGR, and other complications when compared to controls (tHcy: 7.033 ± 2.744, 6.321 ± 3.645, and 6.602 ± 2.469 vs 4.701 ± 2.082 μmol/L, respectively, p value <0.001 and Ut-A resistance index: 0.587 ± 0.072, 0.587 ± 0.053, and 0.597 ± 0.069 vs 0.524 ± 0.025, respectively, p value <0.001). The use of both tHcy assessment and Ut-A Doppler improved the sensitivity of prediction of PE relative to the use of each one alone (85.2 relative to 73.33 and 60%, respectively). The use of elevated homocysteine and uterine artery Doppler screening are valuable in prediction of preeclampsia, IUGR, and poor placentation disorders. CLINCALTRIAL. NCT02854501.

Substorms, Plasmoids, Flux Robes, and Magnetotail Flux Loss on March 25, 1983: CDAW-8

DTIC Science & Technology

1988-10-03

1400 UT. The magnitude and orientation of the 11 GOES 5 OR 1982-01 9A SE14 14 ZSM -l1ORe ISEE 3 -10 -5 5 OReYSM YS m ISEE 1 5 14r- -* IMP 8 0 Fig. lb...and references therein]. ISEE 1 saw a 31% field decrease from 55 nT to 38 nT between 1020 and 1058 UT, and a 35 % decrease from 62 nT to 41 nT between...strength is determined by the component 29 2.5 POLAR CAP AREA 2.0 E ISEE 1 . 5 -i 60 x - 50 IMP 8 - 40 35 ISEE-3 (B = 22nt) 30 25 ISE IMP8 cc" Z u

Effect of continuous annealing temperature on microstructure and properties of ferritic rolled interstitial-free steel

NASA Astrophysics Data System (ADS)

Qiu, Chen-yang; Li, Lang; Hao, Lei-lei; Wang, Jian-gong; Zhou, Xun; Kang, Yong-lin

2018-05-01

In this report, the microstructure, mechanical properties, and textures of warm rolled interstitial-free steel annealed at four different temperatures (730, 760, 790, and 820°C) were studied. The overall structural features of specimens were investigated by optical microscopy, and the textures were measured by X-ray diffraction (XRD). Nano-sized precipitates were then observed by a transmission electron microscope (TEM) on carbon extraction replicas. According to the results, with increased annealing temperatures, the ferrite grains grew; in addition, the sizes of Ti4C2S2 and TiC precipitates also increased. Additionally, the sizes of TiN and TiS precipitates slightly changed. When the annealing temperature increased from 730 to 820°C, the yield strength (YS) and the ultimate tensile strength (UTS) showed a decreasing trend. Meanwhile, elongation and the strain harden exponent (n value) increased to 49.6% and 0.34, respectively. By comparing textures annealed at different temperatures, the intensity of {111} texture annealed at 820°C was the largest, while the difference between the intensity of {111}<110> and {111}<112> was the smallest when the annealing temperature was 820°C. Therefore, the plastic strain ratio (r value) annealed at 820°C was the highest.

Hand grip strength and dexterity function in children aged 6-12 years: A cross-sectional study.

PubMed

Omar, Mohammed T A; Alghadir, Ahmad H; Zafar, Hamayun; Al Baker, Shaheerah

Cross-sectional and clinical measurement. Assessment of hand function considers an essential part in clinical practice. To develop normative values of hand grip strength and dexterity function for 6-12-year-old children in Saudi Arabia. Grip strength and dexterity function was measured in 525 children using Grip Track hand dynamometer (JTECH Medical, Midvale, UT, USA) and 9-hole pegboard test respectively. The grip strength and dexterity function was improved as age progressed regardless of gender. Across all age groups, the hand grip strength of boys was significantly higher than girls for dominant hand (31.75 ± 10.33 vs 28.24 ± 9.35; P < .001) and nondominant hand (31.01 ± 10.27 vs 27.27 ± 9.30; P < .001). The girls performed slightly faster than boys for dominant hand (19.70 vs 20.68; P < .05) and nondominant hand (21.79 vs 23.46; P < .05). In general, girls completed a 9-HPT faster than boys in the 2 of 7 age groups: 11 years (9-HPT scores = 2.10 seconds; P < .01) and 12 years (9-HPT scores = 1.93 seconds; P < .01). The overall patterns of hand grip strength and dexterity function observed in the present study are similar to the previous studies that established acceleration of grip strength with advanced age, and faster performance scores in older children than younger children in both genders. Norms of hand grip strength and dexterity enable therapists to identify some developmental characteristics of hand function among Saudi children, determine the presence of impairment, and compare scores from children in different clinical settings. Not applicable. Copyright © 2017 Hanley & Belfus. Published by Elsevier Inc. All rights reserved.

Effect of tensile pre-strain at different orientation on martensitic transformation and mechanical properties of 316L stainless steel

NASA Astrophysics Data System (ADS)

Wibowo, F.; Zulfi, F. R.; Korda, A. A.

2017-01-01

Deformation induced martensite was studied in 316L stainless steel through tensile pre-strain deformation in the rolling direction (RD) and perpendicular to the rolling direction (LT) at various %pre-strain. The experiment was carried out at various given %pre-strain, which were 0%, 4.6%, 12%, 17.4%, and 25.2% for the RD, whereas for LT were 0%, 4.6%, 12%, 18%, and 26% for LT. Changes in the microstructure and mechanical properties were observed using optical microscope, tensile testing, hardness testing, and X-ray diffraction (XRD) analysis. The experimental results showed that the volume fraction of martensite was increased as the %pre-strain increased. In the same level of deformation by tensile pre-strain, the volume of martensite for RD was higher than that with LT direction. The ultimate tensile strength (UTS), yield strength (YS), and hardness of the steel were increased proportionally with the increases in %pre-strain, while the value of elongation and toughness were decreased with the increases in %pre-strain.

Influence of Fluidized Bed Quenching on the Mechanical Properties and Quality Index of T6 Tempered B319.2-Type Aluminum Alloys

NASA Astrophysics Data System (ADS)

Ragab, Kh. A.; Samuel, A. M.; Al-Ahmari, A. M. A.; Samuel, F. H.; Doty, H. W.

2013-11-01

The current study aimed to investigate the effect of fluidized sand bed (FB) quenching on the mechanical performance of B319.2 aluminum cast alloys. Traditional water and conventional hot air (CF) quenching media were used to establish a relevant comparison with FB quenching. Quality charts were generated using two models of quality indices to support the selection of material conditions on the basis of the proposed quality indices. The use of an FB for the direct quenching-aging treatment of B319.2 casting alloys yields greater UTS and YS values compared to conventional furnace quenched alloys. The strength values of T6 tempered B319 alloys are greater when quenched in water compared with those quenched in an FB or CF. For the same aging conditions (170°C/4h), the fluidized bed quenched-aged 319 alloys show nearly the same or better strength values than those quenched in water and then aged in a CF or an FB. Based on the quality charts developed for alloys subjected to different quenching media, higher quality index values are obtained by conventional furnace quenched-aged T6-tempered B319 alloys. The modification factor has the most significant effect on the quality results of the alloys investigated, for all heat treatment cycles, as compared to other metallurgical parameters. The results of alloys subjected to multi-temperature aging cycles reveal that the optimum strength properties of B319.2 alloys, however, is obtained by applying multi-temperature aging cycles such as, for example, 240 °C/2 h followed by 170 °C/8 h, rather than T6 aging treatments. The regression models indicate that the mean quality values of B319 alloys are highly quench sensitive due to the formation of a larger percent of clusters in Al-Si-Cu-Mg alloys. These clusters act as heterogeneous nucleation sites for precipitation and enhance the aging process.

Effects of ultrasonic pretreatments on quality, energy consumption and sterilization of barley grass in freeze drying.

PubMed

Cao, Xiaohuang; Zhang, Min; Mujumdar, Arun S; Zhong, Qifeng; Wang, Zhushang

2018-01-01

Barley grass is a plant resource for rehabilitation therapy. Its processing requires retaining nutrition well for rehabilitation cure of consumers. To meet the aim as well as low energy consumption and microbiological safety of products, ultrasonic treatments (UT) were applied to bathing materials at different power levels (10, 30, 45, 60W/L) for 10mins. After treatments, the bathed barley grass (100g) was freeze-dried under vacuum -0.09MPa with fixed power of 2W/g. Parameters of color, microbial colony, energy consumption, glass transition temperature, moisture content, water activity, taste substances, contents of flavonoid and chlorophyll were determined after drying. In contrast with no treatment case, UT (45W/L) decreased drying time by 14% and decreased energy consumption by 19%; UT (60W/L) decreased total microbial colonies by 33%. Also, UT (30W/L) yielded contents of flavonoid (9.2/kg) and chlorophyll (10.5g/kg) of dried sample; UT power (10W/L) yielded the highest L ∗ (51.5) and the lowest a ∗ (-9.3) value. Simultaneously, UT leads to a higher glass transition temperature (Tg), lower water activity and produces less sourness and bitterness of dried products. Ultra-sonication is an alternative to improve quality, flavor and energy consumption of barley grass in freeze drying. Copyright © 2017 Elsevier B.V. All rights reserved.

Effects of Retained Austenite Volume Fraction, Morphology, and Carbon Content on Strength and Ductility of Nanostructured TRIP-assisted Steels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shen, Yongfeng; Qiu, LN; Sun, Xin

2015-06-01

With a suite of multi-modal and multi-scale characterization techniques, the present study unambiguously proves that a substantially-improved combination of ultrahigh strength and good ductility can be achieved by tailoring the volume fraction, morphology, and carbon content of the retained austenite (RA) in a transformation-induced-plasticity (TRIP) steel with the nominal chemical composition of 0.19C-0.30Si-1.76Mn-1.52Al (weight percent, wt.%). After intercritical annealing and bainitic holding, a combination ultimate tensile strength (UTS) of 1,100 MPa and true strain of 50% has been obtained, as a result of the ultrafine RA lamellae, which are alternately arranged in the bainitic ferrite around junction regions of ferritemore » grains. For reference, specimens with a blocky RA, prepared without the bainitic holding, yield a low ductility (35%) and a low UTS (800 MPa). The volume fraction, morphology, and carbon content of RA have been characterized using various techniques, including magnetic probing, scanning electron microscopy (SEM), electron-backscatter-diffraction (EBSD), and transmission electron microscopy (TEM). Interrupted tensile tests, mapped using EBSD in conjunction with the kernel average misorientation (KAM) analysis, reveal that the lamellar RA is the governingmicrostructure component responsible for the higher mechanical stability, compared to the blocky one. By coupling these various techniques, we quantitatively demonstrate that in addition to the RA volume fraction, its morphology and carbon content are equally important in optimizing the strength and ductility of TRIP-assisted steels.« less

Tensile Flow Behavior of Tungsten Heavy Alloys Produced by CIPing and Gelcasting Routes

NASA Astrophysics Data System (ADS)

Panchal, Ashutosh; Ravi Kiran, U.; Nandy, T. K.; Singh, A. K.

2018-04-01

Present work describes the flow behavior of tungsten heavy alloys with nominal compositions 90W-7Ni-3Fe, 93W-4.9Ni-2.1Fe, and 95W-3.5Ni-1.5Fe (wt pct) produced by CIPing and gelcasting routes. The overall microstructural features of gelcasting are finer than those of CIPing alloys. Both the grain size of W and corresponding contiguity values increase with increase in W content in the present alloys. The volume fraction of matrix phase decreases with increase in W content in both the alloys. The lattice parameter values of the matrix phase also increase with increase in W content. The yield strength (σ YS) continuously increases with increase in W content in both the alloys. The σ YS values of CIPing alloys are marginally higher than those of gelcasting at constant W. The ultimate tensile strength (σ UTS) and elongation values are maximum at intermediate W content. Present alloys exhibit two slopes in true stress-true plastic strain curves in low and high strain regimes and follow a characteristic Ludwigson relation. The two slopes are associated with two deformation mechanisms that are occurring during tensile deformation. The overall nature of differential curves of all the alloys is different and these curves contain three distinctive stages of work hardening (I, II, and III). This suggests varying deformation mechanisms during tensile testing due to different volume fractions of constituent phases. The slip is the predominant deformation mechanism of the present alloys during tensile testing.

Tensile Flow Behavior of Tungsten Heavy Alloys Produced by CIPing and Gelcasting Routes

NASA Astrophysics Data System (ADS)

Panchal, Ashutosh; Ravi Kiran, U.; Nandy, T. K.; Singh, A. K.

2018-06-01

Present work describes the flow behavior of tungsten heavy alloys with nominal compositions 90W-7Ni-3Fe, 93W-4.9Ni-2.1Fe, and 95W-3.5Ni-1.5Fe (wt pct) produced by CIPing and gelcasting routes. The overall microstructural features of gelcasting are finer than those of CIPing alloys. Both the grain size of W and corresponding contiguity values increase with increase in W content in the present alloys. The volume fraction of matrix phase decreases with increase in W content in both the alloys. The lattice parameter values of the matrix phase also increase with increase in W content. The yield strength ( σ YS) continuously increases with increase in W content in both the alloys. The σ YS values of CIPing alloys are marginally higher than those of gelcasting at constant W. The ultimate tensile strength ( σ UTS) and elongation values are maximum at intermediate W content. Present alloys exhibit two slopes in true stress-true plastic strain curves in low and high strain regimes and follow a characteristic Ludwigson relation. The two slopes are associated with two deformation mechanisms that are occurring during tensile deformation. The overall nature of differential curves of all the alloys is different and these curves contain three distinctive stages of work hardening (I, II, and III). This suggests varying deformation mechanisms during tensile testing due to different volume fractions of constituent phases. The slip is the predominant deformation mechanism of the present alloys during tensile testing.

Cultural Values Predicting Acculturation Orientations: Operationalizing a Quantitative Measure

ERIC Educational Resources Information Center

Ehala, Martin

2012-01-01

This article proposes that acculturation orientations are related to two sets of cultural values: utilitarianism (Ut) and traditionalism (Tr). While utilitarian values enhance assimilation, traditional values support language and identity maintenance. It is proposed that the propensity to either end of this value opposition can be measured by an…

GPS TEC Fluctuations in the Low and High Latitudes During the 2015 St. Patrick`s Day Storm

NASA Astrophysics Data System (ADS)

Chung, Jong-Kyun; Hong, Junseok; Yoo, Sung-Moon; Kim, Jeong-Han; Jee, Geonhwa; Hegai, Valery V.

2017-12-01

As a part of collaborative efforts to understand ionospheric irregularities, the Korea ionospheric scintillation sites (KISS) network has been built based on global positioning system (GPS) receivers with sampling rates higher than 1 Hz. We produce the rate of TEC index (ROTI) to represent GPS TEC fluctuations related to ionospheric irregularities. In the KISS network, two ground-based GPS sites at Kiruna (marker: KIRN; geographic: 67.9° N, 21.4° E; geomagnetic: 65.2° N) and Chuuk (marker: CHUK; geographic: 7.5° N, 151.9° E; geomagnetic: 0.4° N) were selected to evaluate the ROTI value for ionospheric irregularities during the occurrence of the 2015 St. Patrick’s Day storm. The KIRN ROTI values in the aurora region appear to be generally much higher than the CHUK ROTI values in the EIA region. The CHUK ROTI values increased to 0.5 TECU/min around UT=13:00 (LT=23:00) on March 16 in the quiet geomagnetic condition. On March 17, 2015, CHUK ROTI values more than 1.0 TECU/min were measured between UT=9:00 and 12:00 (LT=19:00 and 22:00) during the first main phase of the St. Patrick’s Day storm. This may be due to ionospheric irregularities by increased pre-reversal enhancement (PRE) after sunset during the geomagnetic storm. Post-midnight, the CHUK ROTI showed two peaks of 0.5 TECU/min and 0.3 TECU/min near UT=15:00 (LT=01:00) and UT=18:00 (LT=04:00) at the second main phase. The KIRN site showed significant peaks of ROTI around geomagnetic latitude=63.3° N and MLT=15:40 on the same day. These can be explained by enhanced ionospheric irregularities in the auroral oval at the maximum of AE index

Sources of enhanced SO2 in the tropical Western Pacific UT/LS

NASA Astrophysics Data System (ADS)

Rollins, A. W.; Thornberry, T. D.; Liu, S.; Ray, E. A.; Atlas, E. L.; Navarro, M. A.; Schauffler, S.; Bui, T. V.; Gao, R. S.

2017-12-01

Sulfur dioxide is an important precursor to aerosols in the stratosphere. Typical mixing ratios of SO2 in the tropical upper troposphere and lower stratosphere (UT/LS) are on the order of a few pptv. Convective transport of SO2 from source regions near the surface can produce local enhancements in the UT/LS of more than one order of magnitude compared to typical values. These local enhancements if sufficient in number and/or magnitude might be important for the stratospheric aerosol budget. Here we analyze three such local enhancements observed during the NASA POSIDON mission. We use back-trajectories and tracer species to demonstrate that significant SO2 in the UT/LS on different occasions originated from 1) a volcano in Papua New Guinea, 2) convection over Asia, and 3) transport of air by a typhoon. These examples that were observed on three out of ten flights indicate that significant SO2 over the Western Pacific is not uncommon, and may be an important fraction of the stratospheric aerosol budget.

Effect of in-situ formed Al3Ti particles on the microstructure and mechanical properties of 6061 Al alloy

NASA Astrophysics Data System (ADS)

Gupta, Rahul; Chaudhari, G. P.; Daniel, B. S. S.

2018-03-01

In this study, in situ Titanium-tri-aluminide (Al3Ti) particles reinforced Al 6061 alloy matrix composites were fabricated by the reaction of potassium hexafluorotitanate (K2TiF6) inorganic salt with molten Al 6061 alloy via liquid metallurgy route. The development of in-situ Al3Ti particles and their effects on the mechanical properties such as yield strength (YS), ductility, ultimate tensile strength (UTS) and hardness, and microstructure of Al 6061 alloy were studied. It was observed from the results that in-situ formed Al3Ti particles were blocky in morphology whose average size was around 2.6 ± 1.1 μm. Microstructure studies showed that grain size of Al matrix was reduced due to the nucleating effect of Al3Ti particles. It was observed from the mechanical properties analysis that when the volume fraction of Al3Ti particles was increased, the hardness, UTS and YS of the composites were also increased as compared to that of Al 6061 alloy. An improvement in ductility was observed with the dispersion of Al3Ti particles in base alloy which is contrary to many other composites.

Magnetic susceptibility, artifact volume in MRI, and tensile properties of swaged Zr-Ag composites for biomedical applications.

PubMed

Imai, Haruki; Tanaka, Yoji; Nomura, Naoyuki; Doi, Hisashi; Tsutsumi, Yusuke; Ono, Takashi; Hanawa, Takao

2017-02-01

Zr-Ag composites were fabricated to decrease the magnetic susceptibility by compensating for the magnetic susceptibility of their components. The Zr-Ag composites with a different Zr-Ag ratio were swaged, and their magnetic susceptibility, artifact volume, and mechanical properties were evaluated by magnetic balance, three-dimensional (3-D) artifact rendering, and a tensile test, respectively. These properties were correlated with the volume fraction of Ag using the linear rule of mixture. We successfully obtained the swaged Zr-Ag composites up to the reduction ratio of 96% for Zr-4, 16, 36, 64Ag and 86% for Zr-81Ag. However, the volume fraction of Ag after swaging tended to be lower than that before swaging, especially for Ag-rich Zr-Ag composites. The magnetic susceptibility of the composites linearly decreased with the increasing volume fraction of Ag. No artifact could be estimated with the Ag volume fraction in the range from 93.7% to 95.4% in three conditions. Young's modulus, ultimate tensile strength (UTS), and 0.2% yield strength of Zr-Ag composites showed slightly lower values compared to the estimated values using a linear rule of mixture. The decrease in magnetic susceptibility of Zr and Ag by alloying or combining would contribute to the decrease of the Ag fraction, leading to the improvement of mechanical properties. Copyright © 2016 Elsevier Ltd. All rights reserved.

The Effects of Antimony Addition on the Microstructural, Mechanical, and Thermal Properties of Sn-3.0Ag-0.5Cu Solder Alloy

NASA Astrophysics Data System (ADS)

Sungkhaphaitoon, Phairote; Plookphol, Thawatchai

2018-02-01

In this study, we investigated the effects produced by the addition of antimony (Sb) to Sn-3.0Ag-0.5Cu-based solder alloys. Our focus was the alloys' microstructural, mechanical, and thermal properties. We evaluated the effects by means of scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), differential scanning calorimetry (DSC), and a universal testing machine (UTM). The results showed that a part of the Sb was dissolved in the Sn matrix phase, and the remaining one participated in the formation of intermetallic compounds (IMCs) of Ag3(Sn,Sb) and Cu6(Sn,Sb)5. In the alloy containing the highest wt pct Sb, the added component resulted in the formation of SnSb compound and small particle pinning of Ag3(Sn,Sb) along the grain boundary of the IMCs. Our tests of the Sn-3.0Ag-0.5Cu solder alloys' mechanical properties showed that the effects produced by the addition of Sb varied as a function of the wt pct Sb content. The ultimate tensile strength (UTS) increased from 29.21 to a maximum value of 40.44 MPa, but the pct elongation (pct EL) decreased from 48.0 to a minimum 25.43 pct. Principally, the alloys containing Sb had higher UTS and lower pct EL than Sb-free solder alloys due to the strengthening effects of solid solution and second-phase dispersion. Thermal analysis showed that the alloys containing Sb had a slightly higher melting point and that the addition amount ranging from 0.5 to 3.0 wt pct Sb did not significantly change the solidus and liquidus temperatures compared with the Sb-free solder alloys. Thus, the optimal concentration of Sb in the alloys was 3.0 wt pct because the microstructure and the ultimate tensile strength of the SAC305 solder alloys were improved.

Transgenic Restoration of Urea Transporter A1 Confers Maximal Urinary Concentration in the Absence of Urea Transporter A3.

PubMed

Klein, Janet D; Wang, Yanhua; Mistry, Abinash; LaRocque, Lauren M; Molina, Patrick A; Rogers, Richard T; Blount, Mitsi A; Sands, Jeff M

2016-05-01

Urea has a critical role in urinary concentration. Mice lacking the inner medullary collecting duct (IMCD) urea transporter A1 (UT-A1) and urea transporter A3 (UT-A3) have very low levels of urea permeability and are unable to concentrate urine. To investigate the role of UT-A1 in the concentration of urine, we transgenically expressed UT-A1 in knockout mice lacking UT-A1 and UT-A3 using a construct with a UT-A1 gene that cannot be spliced to produce UT-A3. This construct was inserted behind the original UT-A promoter to yield a mouse expressing only UT-A1 (UT-A1(+/+)/UT-A3(-/-)). Western blot analysis demonstrated UT-A1 in the inner medulla of UT-A1(+/+)/UT-A3(-/-) and wild-type mice, but not in UT-A1/UT-A3 knockout mice, and an absence of UT-A3 in UT-A1(+/+)/UT-A3(-/-) and UT-A1/UT-A3 knockout mice. Immunohistochemistry in UT-A1(+/+)/UT-A3(-/-) mice also showed negative UT-A3 staining in kidney and other tissues and positive UT-A1 staining only in the IMCD. Urea permeability in isolated perfused IMCDs showed basal permeability in the UT-A1(+/+)/UT-A3(-/-) mice was similar to levels in wild-type mice, but vasopressin stimulation of urea permeability in wild-type mice was significantly greater (100% increase) than in UT-A1(+/+)/UT-A3(-/-) mice (8% increase). Notably, basal urine osmolalities in both wild-type and UT-A1(+/+)/UT-A3(-/-) mice increased upon overnight water restriction. We conclude that transgenic expression of UT-A1 restores basal urea permeability to the level in wild-type mice but does not restore vasopressin-stimulated levels of urea permeability. This information suggests that transgenic expression of UT-A1 alone in mice lacking UT-A1 and UT-A3 is sufficient to restore urine-concentrating ability. Copyright © 2016 by the American Society of Nephrology.

Transgenic Restoration of Urea Transporter A1 Confers Maximal Urinary Concentration in the Absence of Urea Transporter A3

PubMed Central

Wang, Yanhua; Mistry, Abinash; LaRocque, Lauren M.; Molina, Patrick A.; Rogers, Richard T.; Blount, Mitsi A.; Sands, Jeff M.

2016-01-01

Urea has a critical role in urinary concentration. Mice lacking the inner medullary collecting duct (IMCD) urea transporter A1 (UT-A1) and urea transporter A3 (UT-A3) have very low levels of urea permeability and are unable to concentrate urine. To investigate the role of UT-A1 in the concentration of urine, we transgenically expressed UT-A1 in knockout mice lacking UT-A1 and UT-A3 using a construct with a UT-A1 gene that cannot be spliced to produce UT-A3. This construct was inserted behind the original UT-A promoter to yield a mouse expressing only UT-A1 (UT-A1+/+/UT-A3−/−). Western blot analysis demonstrated UT-A1 in the inner medulla of UT-A1+/+/UT-A3−/− and wild-type mice, but not in UT-A1/UT-A3 knockout mice, and an absence of UT-A3 in UT-A1+/+/UT-A3−/− and UT-A1/UT-A3 knockout mice. Immunohistochemistry in UT-A1+/+/UT-A3−/− mice also showed negative UT-A3 staining in kidney and other tissues and positive UT-A1 staining only in the IMCD. Urea permeability in isolated perfused IMCDs showed basal permeability in the UT-A1+/+/UT-A3−/− mice was similar to levels in wild-type mice, but vasopressin stimulation of urea permeability in wild-type mice was significantly greater (100% increase) than in UT-A1+/+/UT-A3−/− mice (8% increase). Notably, basal urine osmolalities in both wild-type and UT-A1+/+/UT-A3−/− mice increased upon overnight water restriction. We conclude that transgenic expression of UT-A1 restores basal urea permeability to the level in wild-type mice but does not restore vasopressin-stimulated levels of urea permeability. This information suggests that transgenic expression of UT-A1 alone in mice lacking UT-A1 and UT-A3 is sufficient to restore urine-concentrating ability. PMID:26407594

High-Strength Low-Alloy Steel Strengthened by Multiply Nanoscale Microstructures

NASA Astrophysics Data System (ADS)

Shen, Y. F.; Zuo, L.

Recently, we have being focused on improving the strength without sacrificing ductility of High-strength low-alloy (HSLA) steels by designing nanostructures. Several developments have been obtained, summarized as the following three parts: (a) Depressively nanoscale precipitates: A ferritic steel with finely dispersed precipitates reveals a yield strength of 760 MPa, approximately three times higher than that of conventional Ti-bearing high strength hot-rolled sheet steels, and its ultimate tensile strength reaches 850 MPa with an elongation-to-failure value of 18%. The finely dispersed TiC precipitates in the matrix provide matrix strengthening. The estimated magnitude of precipitation strengthening is around 458 MPa. The effects of the particle size, particle distribution and intrinsic particle strength have been investigated through dislocation dynamics (DD) simulations. The DD results show that strengthening is not only a function of the density of the nano-scale precipitates but also of their size. (b) Ultrafinely ferritic plate: An interstitial-free (IF) steel sheet with a cold-rolling reduction of 75% shows a high tensile strength (710MPa) while preserving a considerable plastic strain (13%). The ductility recovery with increasing the rolling reduction up to 75% is related with the decreasing both in lamellar spacings and cell blocks sizes. (c) Parallel nano-laminated austenite: A composite microstructure consisting of ferrite, bainitic ferrite (BF) laths and retained austenite (RA) platelets has been found for the steel with a chemical composition of 0.19C-0.30Si-1.76Mn-1.52Al (in mass fraction), processed with annealing and bainitic holding. The sample annealed at 820oC (for 120s) and partitioned at 400oC (for 300s) has the best combination of ultimate tensile strength (UTS, 682 MPa) and elongation to failure ( 70%) with about 26% of BF plates 16% RA in its microstructure.

Modified natural fibrils for structural hybrid composites: Towards an investigation of textile reduction

NASA Astrophysics Data System (ADS)

Ufodike, Chukwuzubelu Okenwa

Recently, the interest for renewable resources for fibers particularly of plant origin has been increasing. Reduction of use of traditional textile materials is now considered more critical due to the increasing environmental concern. Natural fibers are renewable, biodegradable, recyclable, and lightweight materials with high specific modulus, in competition with man-made fossil materials and fiberglass. Natural fibers are used for preparation of functionalized textiles to achieve smart and intelligent properties. However, the incorporation of these fibers in composite systems has been challenging due to their hydrophilic nature. Nevertheless, the fact that these biodegradable materials can be manipulated at a nano-scale to complement desired objective and application has made them a favorable option. The idea behind this project is to explore ways to convert green waste to high value materials and to utilize natural building blocks to design textile reinforcement materials. In this work, cellulose nanofibrils (CNF) supplied from the University of Maine were hydrophobized by silylation and characterized using Fourier-Transform Infrared (FTIR) spectroscopy, Raman spectroscopy, and Thermogravimetric analysis (TGA). Results from FTIR spectroscopy showed a formation of Si-O-C bonds, indicating better fiber-matrix adhesion. Raman spectroscopy showed disruption of hydrogen bonding which indicates interference of parallel nanocellulose fiber adhesion to neighboring fibrils. The TGA suggests that the thermal stability of the functionalized CNF is higher than that of the corresponding neat sample, which could be a result of stable Si bond formation. The raw materials (neat and functionalized) were encapsulated in a polystyrene matrix through a solvent and non-solvent precipitation process, and then extruded using single and dual heat processing. The extruded thin filaments were tested according to the ASTM D638 (tensile test of plastics). Results showed an increasing Ultimate Tensile Strength (UTS) and Elastic Modulus, with peak values attributed to the dual-heat processing up to 79% and 69% increase respectively at 5wt% loading. Further increase was seen at 10wt% loading up to 112MPa UTS, and modulus up to 10.7GPa for the dual-heat processing. The UTS increase is assumed to be a result of linear arrangement of CNF in the matrix during the extrusion process. The results revealed the strong reinforcing ability of CNF and their compatibility with thermoplastic matrix if functionalized.

Structure and mechanical properties of Cresco-Ti laser-welded joints and stress analyses using finite element models of fixed distal extension and fixed partial prosthetic designs.

PubMed

Uysal, Hakan; Kurtoglu, Cem; Gurbuz, Riza; Tutuncu, Naki

2005-03-01

The Cresco-Ti System uses a laser-welded process that provides an efficient technique to achieve passive fit frameworks. However, mechanical behavior of the laser-welded joint under biomechanical stress factors has not been demonstrated. This study describes the effect of Cresco-Ti laser-welding conditions on the material properties of the welded specimen and analyzes stresses on the weld joint through 3-dimensional finite element models (3-D FEM) of implant-supported fixed dentures with cantilever extensions and fixed partial denture designs. Twenty Grade III (ASTM B348) commercially pure titanium specimens were machine-milled to the dimensions described in the EN10002-1 tensile test standard and divided into test (n = 10) and control (n = 10) groups. The test specimens were sectioned and laser-welded. All specimens were subjected to tensile testing to determine yield strength (YS), ultimate tensile strength (UTS), and percent elongation (PE). The Knoop micro-indentation test was performed to determine the hardness of all specimens. On welded specimens, the hardness test was performed at the welded surface. Data were analyzed with the Mann-Whitney U test and Student's t test (alpha=.05). Fracture surfaces were examined by scanning electron microscopy to characterize the mode of fracture and identify defects due to welding. Three-dimensional FEMs were created that simulated a fixed denture with cantilever extensions supported by 5 implants (M1) and a fixed partial denture supported by 2 implants (M2), 1 of which was angled 30 degrees mesio-axially. An oblique load of 400 N with 15 degrees lingual-axial inclinations was applied to both models at various locations. Test specimens fractured between the weld and the parent material. No porosities were observed on the fractured surfaces. Mean values for YS, UTS, PE, and Knoop hardness were 428 +/- 88 MPa, 574 +/- 113 MPa, 11.2 +/- 0.4%, 270 +/- 17 KHN, respectively, for the control group and 642 +/- 2 MPa, 772 +/- 72 MPa, 4.8 +/- 0.7%, 353 +/- 23 KHN, respectively, for the test group. The differences between the groups were significant for all mechanical properties ( P <.05). For both models, the FEA revealed that maximum principal stresses were concentrated at the framework-weld junction but did not exceed the UTS of the weld joint. Within the constraints of the finite element models, mechanical failure of the welded joint between the support and the framework may not be expected under biomechanical conditions simulated in this study.

Latitudinal features of Total Electron Content over the African and European longitude sector following the St. Patrick's day storm of 2015

NASA Astrophysics Data System (ADS)

Paul, A.; Kascheyev, A.; Rodriguez-Bouza, M.; Pathak, K.; Ferreira, A. A.; Shetti, D.; Yao, J. N.

2018-04-01

GNSS TEC values have been obtained from 18 stations distributed from the magnetic equator to nearly 80°N magnetic dip in the African and west-European longitude sector corresponding to the March 17-18, 2015 geomagnetic storm. Significantly depleted ionosphere have been observed at stations north of 50°N geographic on March 18, 2015 following the above storm over a longitude swath 11.9°-21°E covering the Eastern Africa and Western European longitude sector. High ROTI values were noted on March 17th at locations around 80°N magnetic dip. Two prominent peaks in PCN were noted around 09:00 UT and 14:00 UT on March 17, 2015 and around 15:00 UT on March 18, 2015. Daytime thermospheric (O/N2) ratio was markedly less on March 18th at latitudes above 60°N geographic which is suggested to be the major driver behind depleted high latitude ionosphere during the recovery phase of the storm on March 18, 2015.

4-station ultra-rapid EOP experiment with e-VLBI technique and automated correlation/analysis

NASA Astrophysics Data System (ADS)

Kurihara, S.; Nozawa, K.; Haas, R.; Lovell, J.; McCallum, J.; Quick, J.; Hobiger, T.

2013-08-01

Since 2007, the Geospatial Information Authority of Japan (GSI) and the Onsala Space Observatory (OSO) have performed the ultra-rapid dUT1 experiments, which can provide us with near real-time dUT1 value. Its technical knowledge has already been adopted for the regular series of the Tsukuba-Wettzell intensive session. Now we tried some 4-station ultra-rapid EOP experiments in association with Hobart and HartRAO so that we can estimate not only dUT1 but also the two polar motion parameters. In this experiment a new analysis software c5++ developed by the National Institute of Information and Communications Technology (NICT) was used. We describe past developments and an overview of the experiment, and conclude with its results in this report.

An Observational and Modeling Study of Auroral Upwelling in the Thermosphere

DTIC Science & Technology

2016-04-28

0000UT) on each of the nights of 15 and 17 February 2015. The Kilpisjärvi Atmospheric Imaging Receiver Array (KAIRA) provided additional line-of...photoionisation based on solar fluxes, Figure 5 Conventional Joule heating in the region 110-150 km (Thayer et al., 1995) Distribution A: Approved...i.e. 2100 UT). The simulations are for January solar minimum, using f10.7 value of 80 and quiet steady state conditions. Table 1: Four CMAT2

Microstructure and Strain Rate-Dependent Tensile Deformation Behavior of Fiber Laser-Welded Butt Joints of Dual-Phase Steels

NASA Astrophysics Data System (ADS)

Liu, Yang; Dong, Danyang; Han, Zhiqiang; Yang, Zhibin; Wang, Lu; Dong, Qingwei

2018-05-01

The microstructure and tensile deformation behavior of the fiber laser-welded similar and dissimilar dual-phase (DP) steel joints over a wide range of strain rates from 10-3 to 103 s-1 were investigated for the further applications on the lightweight design of vehicles. The high strain rate dynamic tensile deformation process and full-field strain distribution of the base metals and welded joints were examined using the digital image correlation method and high-speed photography. The strain rate effects on the stress-strain responses, tensile properties, deformation, and fracture behavior of the investigated materials were analyzed. The yield stress (YS) and ultimate tensile strength (UTS) of the dissimilar DP780/DP980 welded joints were lying in-between those of the DP780 and DP980 base metals, and all materials exhibited positive strain rate dependence on the YS and UTS. Owing to the microstructure heterogeneity, the welded joints showed relatively lower ductility in terms of total elongation (TE) than those of the corresponding base metals. The strain localization started before the maximum load was reached, and the strain localization occurred earlier during the whole deformation process with increasing strain rate. As for the dissimilar welded joint, the strain localization tended to occur in the vicinity of the lowest hardness value across the welded joint, which was in the subcritical HAZ at the DP780 side. As the strain rate increased, the typical ductile failure characteristic of the investigated materials did not change.

Microstructure and Strain Rate-Dependent Tensile Deformation Behavior of Fiber Laser-Welded Butt Joints of Dual-Phase Steels

NASA Astrophysics Data System (ADS)

Liu, Yang; Dong, Danyang; Han, Zhiqiang; Yang, Zhibin; Wang, Lu; Dong, Qingwei

2018-04-01

The microstructure and tensile deformation behavior of the fiber laser-welded similar and dissimilar dual-phase (DP) steel joints over a wide range of strain rates from 10-3 to 103 s-1 were investigated for the further applications on the lightweight design of vehicles. The high strain rate dynamic tensile deformation process and full-field strain distribution of the base metals and welded joints were examined using the digital image correlation method and high-speed photography. The strain rate effects on the stress-strain responses, tensile properties, deformation, and fracture behavior of the investigated materials were analyzed. The yield stress (YS) and ultimate tensile strength (UTS) of the dissimilar DP780/DP980 welded joints were lying in-between those of the DP780 and DP980 base metals, and all materials exhibited positive strain rate dependence on the YS and UTS. Owing to the microstructure heterogeneity, the welded joints showed relatively lower ductility in terms of total elongation (TE) than those of the corresponding base metals. The strain localization started before the maximum load was reached, and the strain localization occurred earlier during the whole deformation process with increasing strain rate. As for the dissimilar welded joint, the strain localization tended to occur in the vicinity of the lowest hardness value across the welded joint, which was in the subcritical HAZ at the DP780 side. As the strain rate increased, the typical ductile failure characteristic of the investigated materials did not change.

Response of the mid-latitude D-region ionosphere to the total solar eclipse of 22 July 2009 studied using VLF signals in South Korean peninsula

NASA Astrophysics Data System (ADS)

Phanikumar, D. V.; Kwak, Y.-S.; Patra, A. K.; Maurya, A. K.; Singh, Rajesh; Park, S.-M.

2014-09-01

In this paper, we analyze VLF signals received at Busan to study the the D-region changes linked with the solar eclipse event of 22 July 2009 for very short (∼390 km) transmitter-receiver great circle path (TRGCP) during local noon time 00:36-03:13 UT (09:36-12:13 KST). The eclipse crossed south of Busan with a maximum obscuration of ∼84%. Observations clearly show a reduction of ∼6.2 dB in the VLF signal strength at the time of maximum solar obscuration (84% at 01:53 UT) as compared to those observed on the control days. Estimated values of change in Wait ionospheric parameters: reflection height (h‧) in km and inverse scale height parameter (β) in km-1 from Long Wave Propagation Capability (LWPC) model during the maximum eclipse phase as compared to unperturbed ionosphere are 7 km and 0.055 km-1, respectively. Moreover, the D-region electron density estimated from model computation shows 95% depletion in electron density at the height of ∼71 km. The reflection height is found to increase by ∼7 km in the D-region during the eclipse as compared to those on the control days, implying a depletion in the Lyman-α flux by a factor of ∼7. The present observations are discussed in the light of current understanding on the solar eclipse induced D-region dynamics.

Tensile bond strength of an aged resin composite repaired with different protocols.

PubMed

Celik, Esra Uzer; Ergücü, Zeynep; Türkün, L Sebnem; Ercan, Utku Kürșat

2011-08-01

To evaluate the effect of different surface treatments and bonding procedures on the tensile bond strength (TBS) of resin composites repaired 6 months after polymerization. Resin composite sticks were aged in distilled water at 37°C for 6 months. They were divided into 12 groups (n = 10) according to the combination of surface treatment/bonding procedures [none, only bur treatment, XP Bond (XPB/Dentsply/DeTrey) with/without bur, AdheSE (A-SE/Ivoclar/Vivadent) with/without bur, Composite Primer (CP/GC) with/without bur, CP after bur and acid-etching, XPB after acid etching and CP with bur, A-SE after bur and CP]. The ultimate tensile bond strength (UTS) of the resin composites was tested in intact but aged specimens. Tensile bond strengths were tested with a universal testing machine (Shimadzu). Data were analyzed using one-way ANOVA and Duncan Multiple Comparisons tests (p < 0.05). All repaired groups showed significantly higher TBS than the group without any sureface treatment (p < 0.05). Four groups resulted in TBS similar to those of intact resin composite UTS: A-SE, A-SE with bur, A-SE after CP with bur, and XPB after acid etching+CP with bur. Bur treatment, silane primer or etch-and-rinse adhesive application alone were not successful in the repair process of aged resin composite, whereas self-etching adhesive alone showed similar performance to the intact specimens. Combined procedures generally showed better performance: A-SE with bur, A-SE after CP with bur, and XPB after acid etching +CP with bur showed TBS similar to those of the intact specimens. It was concluded that bur roughening of the surfaces and rebonding procedures were essential for repairing aged resin composites.

Microstructure, Texture, and Mechanical Behavior of As-cast Ni-Fe-W Matrix Alloy

NASA Astrophysics Data System (ADS)

Rao, A. Sambasiva; Manda, Premkumar; Mohan, M. K.; Nandy, T. K.; Singh, A. K.

2018-04-01

This article describes the tensile properties, flow, and work-hardening behavior of an experimental alloy 53Ni-29Fe-18W in as-cast condition. The microstructure of the alloy 53Ni-29Fe-18W displays single phase (fcc) in as-cast condition along with typical dendritic features. The bulk texture of the as-cast alloy reveals the triclinic sample symmetry and characteristic nature of coarse-grained materials. The alloy exhibits maximum strength ( σ YS and σ UTS) values along the transverse direction. The elongation values are maximum and minimum along the transverse and longitudinal directions, respectively. Tensile fracture surfaces of both the longitudinal and transverse samples display complete ductile fracture features. Two types of slip lines, namely, planar and intersecting, are observed in deformed specimens and the density of slip lines increases with increasing the amount of deformation. The alloy displays moderate in-plane anisotropy ( A IP) and reasonably low anisotropic index ( δ) values, respectively. The instantaneous or work-hardening rate curves portray three typical stages (I through III) along both the longitudinal and transverse directions. The alloy exhibits dislocation-controlled strain hardening during tensile testing, and slip is the predominant deformation mechanism.

Architectures for High-Performance Ceramic Composites Being Improved

NASA Technical Reports Server (NTRS)

Yun, Hee Mann; DiCarlo, James A.

2002-01-01

A major thrust of the Ultra-Efficient Engine Technology (UEET) Program at the NASA Glenn Research Center is to develop advanced hot-section engine components using SiC/SiC ceramic matrix composites (CMC's) with thermostructural capability to 2400 F (1315 C). In previous studies, UEET determined that the higher the ultimate tensile strength (UTS) of the as-fabricated CMC, the greater its structural performance at 2400 F. Thus efforts have been ongoing within UEET to understand and develop fiber architecture approaches that can improve the UTS of SiC/SiC CMC's. Under UEET, SiC/SiC test panels and demonstration engine components are currently produced by the multi-ply layup of two-dimensional fabric pieces. The fabric is typically formed of multifilament tows containing high-performance Sylramic (Dow Corning) SiC fiber that is woven into two-dimensional five-harness satin fabric with 20 ends per inch in the 0 degree and 90 degree directions. In some cases, fabric pieces containing woven Sylramic fiber tows are thermally treated at NASA to form Sylramic-iBN fibers that contain a very thin in-situ-grown boron nitride layer on their surfaces. The final SiC/SiC panels and components are fabricated at the CMC vendor by compressing the fabric pieces in tools and then depositing a thin BN interphase coating on the fibers by chemical vapor deposition. The last step at the vendor is to infiltrate the BN-coated fiber architecture with SiC and silicon matrix constituents to form a dense product. Because the as-produced Sylramic fiber tows are sized with a thin polymer coating to facilitate handling and weaving, the individual fibers within the tows and fabric are in close contact with each other. This contact is further increased during fabric compression. One important recent finding is that increasing Sylramic fiber tow width in a fabric increases the UTS of the final SiC/SiC CMC. This effect is presumably related to minimizing fiber/fiber contact, which can be detrimental to CMC strength because of the boron-rich chemistry and roughness of the Sylramic fiber surface. Tows can be spread by mechanically agitating the Sylramic fabric prior to CMC fabrication or by simply thermally treating the Sylramic fabric as in the formation of the Sylramic-iBN fibers. However, CMC's with the treated Sylramic-iBN fabric are even stronger than CMC's with mechanically spread Sylramic tows. The extra strength capability is presumably related to the in situ BN on the fiber surface, which adds compliance to the fiber surfaces and is more resistant to oxygen impurities introduced during the chemical vapor deposition BN process. As shown, another important finding is that the use of fabric with tows having less than the standard of 20 ends per inch provides advantages in terms of reduced ply height and increased ply and CMC strength. The reduced ply height provides more control of part thickness by allowing more plies for a given thickness and by reducing interlaminar residual stresses between plies. The increased ply strength is presumably related to a reduced number of interlaced 90 tows, which, in turn, reduces the crimp angle on the high-modulus fibers in the 0 degree tows. Also, as shown, although fabric with fewer ends per inch reduced the maximum fiber fraction in an eight-ply CMC panel; CMC UTS actually increased because of increased ply strength. Thus, using fabric with fewer ends per inch has several advantages, including providing a significantly higher strength per fiber fraction in the CMC. Consequently, ongoing UEET efforts will attempt to use architectural approaches for components that minimize fiber-fiber contacts and fiber bending within the final composite microstructure.

Taylor dispersion in premixed combustion: Questions from turbulent combustion answered for laminar flames

NASA Astrophysics Data System (ADS)

Daou, Joel; Pearce, Philip; Al-Malki, Faisal

2018-02-01

We present a study of Taylor dispersion in premixed combustion and use it to clarify fundamental issues related to flame propagation in a flow field. In particular, simple analytical formulas are derived for variable density laminar flames with arbitrary Lewis number Le providing clear answers to important questions arising in turbulent combustion, when these questions are posed for the case of one-scale laminar parallel flows. Exploiting, in the context of a laminar Poiseuille flow model, a thick flame distinguished asymptotic limit for which the flow amplitude is large with the Reynolds number Re fixed, three main contributions are made. First, a link is established between Taylor dispersion [G. Taylor, Proc. R. Soc. London Ser. A 219, 186 (1953), 10.1098/rspa.1953.0139] and Damköhler's second hypothesis [G. Damköhler, Ber. Bunsen. Phys. Chem. 46, 601 (1940)] by describing analytically the enhancement of the effective propagation speed UT due to small flow scales. More precisely, it is shown that Damköhler's hypothesis is only partially correct for one-scale parallel laminar flows. Specifically, while the increase in UT due to the flow is shown to be directly associated with the increase in the effective diffusivity as suggested by Damköhler, our results imply that UT˜Re (for Re≫1 ) rather than UT˜√{Re} , as implied by Damköhler's hypothesis. Second, it is demonstrated analytically and confirmed numerically that, when UT is plotted versus the flow amplitude for fixed values of Re, the curve levels off to a constant value depending on Re. We may refer to this effect as the laminar bending effect as it mimics a similar bending effect known in turbulent combustion. Third, somewhat surprising implications associated with the dependence of UT and of the effective Lewis number Leeff on the flow are reported. For example, Leeff is found to vary from Le to Le-1 as Re varies from small to large values. Also, UT is found to be a monotonically increasing function of Re if Le<√{2 } and a nonmonotonic function if Le>√{2 } .

Relationship between the number of repetitions and selected percentages of one repetition maximum in free weight exercises in trained and untrained men.

PubMed

Shimano, Tomoko; Kraemer, William J; Spiering, Barry A; Volek, Jeff S; Hatfield, Disa L; Silvestre, Ricardo; Vingren, Jakob L; Fragala, Maren S; Maresh, Carl M; Fleck, Steven J; Newton, Robert U; Spreuwenberg, Luuk P B; Häkkinen, Keijo

2006-11-01

Resistance exercise intensity is commonly prescribed as a percent of 1 repetition maximum (1RM). However, the relationship between percent 1RM and the number of repetitions allowed remains poorly studied, especially using free weight exercises. The purpose of this study was to determine the maximal number of repetitions that trained (T) and untrained (UT) men can perform during free weight exercises at various percentages of 1RM. Eight T and 8 UT men were tested for 1RM strength. Then, subjects performed 1 set to failure at 60, 80, and 90% of 1RM in the back squat, bench press, and arm curl in a randomized, balanced design. There was a significant (p < 0.05) intensity x exercise interaction. More repetitions were performed during the back squat than the bench press or arm curl at 60% 1RM for T and UT. At 80 and 90% 1RM, there were significant differences between the back squat and other exercises; however, differences were much less pronounced. No differences in number of repetitions performed at a given exercise intensity were noted between T and UT (except during bench press at 90% 1RM). In conclusion, the number of repetitions performed at a given percent of 1RM is influenced by the amount of muscle mass used during the exercise, as more repetitions can be performed during the back squat than either the bench press or arm curl. Training status of the individual has a minimal impact on the number of repetitions performed at relative exercise intensity.

Baseline UT Measurements for Armor Inspection

NASA Astrophysics Data System (ADS)

Margetan, Frank J.; Richter, Nate; Barnard, Dan; Hsu, David; Gray, Tim; Brasche, Lisa; Bruce Thompson, R.

2010-02-01

Some prototype armor panels are fabricated from several layers of dissimilar material bonded together. These may include ceramics, graphite composites, fiberglass composites and rubber. The ultrasonic properties of these layers influence inspections for armor defects. In this paper we describe measurements of ultrasonic velocity, attenuation, sound beam distortion and signal fluctuations for the individual layers comprising one armor prototype. We then discuss how knowledge of these properties can be used when choosing an optimum frequency for an ultrasonic pitch/catch immersion inspection. In our case an effective inspection frequency near 1.5 MHz affords: (1) adequate strength of through-transmitted signals in unflawed armor; (2) adequate lateral resolution for detecting small disbonds at interfaces; and (3) low levels of UT signal fluctuations due to the natural inhomogeneity of certain armor layers. The utility of this approach is demonstrated using armor panels containing artificial disbonds at selected interfaces.

An evaluation of GTAW-P versus GTA welding of alloy 718

NASA Technical Reports Server (NTRS)

Gamwell, W. R.; Kurgan, C.; Malone, T. W.

1991-01-01

Mechanical properties were evaluated to determine statistically whether the pulsed current gas tungsten arc welding (GTAW-P) process produces welds in alloy 718 with room temperature structural performance equivalent to current Space Shuttle Main Engine (SSME) welds manufactured by the constant current GTAW-P process. Evaluations were conducted on two base metal lots, two filler metal lots, two heat input levels, and two welding processes. The material form was 0.125-inch (3.175-mm) alloy 718 sheet. Prior to welding, sheets were treated to either the ST or STA-1 condition. After welding, panels were left as welded or heat treated to the STA-1 condition, and weld beads were left intact or machined flush. Statistical analyses were performed on yield strength, ultimate tensile strength (UTS), and high cycle fatigue (HCF) properties for all the post welded material conditions. Analyses of variance were performed on the data to determine if there were any significant effects on UTS or HCF life due to variations in base metal, filler metal, heat input level, or welding process. Statistical analyses showed that the GTAW-P process does produce welds with room temperature structural performance equivalent to current SSME welds manufactured by the GTAW process, regardless of prior material condition or post welding condition.

Microstructural evolution and mechanical properties of a low alloy high strength Ni-Cr-Mo-V steel during heat treatment process

NASA Astrophysics Data System (ADS)

Wu, C.; Han, S.

2018-05-01

In order to obtain an optimal heat treatment for a low alloy high strength Ni-Cr-Mo-V steel, the microstructural evolution and mechanical properties of the material were studied. For this purpose, a series of quenching and temper experiments were carried out. The results showed that the effects of tempering temperature, time, original microstructure on the microstructural evolution and final properties were significant. The martensite can be completely transformed into the tempered lath structure. The width and length of the lath became wider and shorter, respectively with increasing temperature and time. The amount and size of the precipitates increased with temperature and time. The yield strength (YS), ultimate tensile strength (UTS) and hardness decreased with temperature and time, but the reduction in area (Z), elongation (E) and impact toughness displayed an opposite trend, which was related to the morphological evolution of the lath tempered structure.

Using GMD Data, AIRS Measurements, and the NASA Chemistry-Climate Model to Reveal Regional and Seasonal Variation of Methane

NASA Astrophysics Data System (ADS)

Steele, K. J.; Duncan, B. N.; Warner, J. X.; Nielsen, J. E.

2010-12-01

The concentration of methane (CH4) has more than doubled in the atmosphere since the preindustrial era due to a change in source-sink interactions. Many studies have aimed to quantify CH4 source contributions, but 1) the long tropospheric lifetime of CH4, resulting in a high background concentration, 2) along with sources often having overlapping distributions, and 3) the uncertainty in the chemical sink of CH4 with the hydroxyl radical makes it difficult to constrain inputs to the CH4 budget. The purpose of this study was to use a variety of observations in conjunction with the NASA GEOS-5 climate-chemistry model (CCM) to better understand regional and seasonal variation in atmospheric CH4. Seasonal variation in surface in situ data from the NOAA ESRL Global Monitoring Division (GMD) and data from the Japanese Airlines (JAL) in the upper troposphere (UT) were compared to satellite observations recorded by the Atmospheric Infrared Sounder (AIRS) on the EOS/Aqua satellite, which is most sensitive to CH4 in the UT. There was more variability in CH4 at the GMD sites than in the JAL data or AIRS because the GMD sites are closer to the source. As the CH4 is lofted into the UT, it mixes with the background CH4 so the seasonal variation is dampened. The JAL data followed the AIRS observations as expected. There was less variability in all measurements in the Southern Hemisphere and over oceans because these areas are farther away from sources. While the observations from AIRS, JAL flights, and the GMD sites provide valuable information regarding source locations and atmospheric CH4 concentration, it is important to understand which CH4 sources have the largest contribution to CH4 emissions in different regions of the world and the influence of these sources on the global CH4 cycle. Model output from the GEOS-5 CCM was used to monitor individual CH4 sources (e.g. from rice production, wetlands, biofuel use, etc.) as they are transported from the surface to the UT. The model revealed that variation in source strength is dependent on the site location in relation to the source strength. Assessing CH4 source contributions to the UT revealed that variability is affected by seasonal variation in the sources convolved with seasonal variation in deep convection. More work is needed in order to constrain sources of atmospheric CH4. However, surface and tropospheric in situ data can be used to validate AIRS observations so that CH4 can be monitored at a global scale, and CCM output can aid in determining which sources have the largest contribution to atmospheric CH4.

Multi-Instrument Analysis of a Traveling Convection Vortex Event on July 24, 1996 Coordinated with the Polar UVI

NASA Technical Reports Server (NTRS)

Sitar, R. J.; Clauer, C. R.; Baker, J. B.; Ridley, A. J.; Cumnock, J.; Germany, G. A.; Spann, J. F., Jr.; Brittnacher, M. J.; Parks, G. K.

1998-01-01

We present the analysis of a coordinated set of observations from the POLAR Ultraviolet Imager (UVI), ground magnetometers, incoherent scatter radar, solar wind monitors, DMSP and GOES satellites, focused on a traveling convection vortex (TCV) event on 24th July 1996. Starting at approximately 10:48 UT, around magnetometers in Greenland and northern Canada observe pulsations consistent with the passing overhead of a series of alternating TCV filed-aligned current pairs. Azimuthal scans by the Sondrestrom incoherent scatter radar located near Kangerlussuaq (formerly Sondrestrom), Greenland, at this time show strong modulation in the strength and direction of ionospheric plasma flow. The magnetometer pulsations grow in magnitude over the next hour, peaking in intensity at 11:39 UT, at which time images form the UVI instrument show a localized intensification of auroral emissions over central and western Greenland. Subsequent images show the intensification grow in strength and propagate westward (tailward) until approximately 11:58 UT at which time the intensification fades. These observations are consistent with the westward passage of two pairs of moderately intense TCVs over central Greenland followed by a third very intense TCV pair. The intensification of auroral emissions at 11:39 UT is associated with the trailing vortex of the third TCV pair, thought to be the result of an upward field aligned current. The modulated flow observed by the radar is the result of the strong electric fields associated with the impulsive TCV related field aligned current systems as they pass through the field of view of the radar. Measurements of the solar wind from the V;IND and IMP-8 spacecraft suggest that a pressure change may be responsible for triggering the first two pairs of TCVS, and that a subsequent sudden change in the orientation of the interplanetary magnetic field may have produced the intensification of the third TCV pair and the associated auroral brightening. Magnetometer data from the GOES satellite located over the eastern United States at geostationary orbit is consistent with a series of field-aligned moving tailward past the satellite. DMSP particle data indicated that the TCVs occur on field lines which map to the boundary plasma sheet (BPS).

Bonding durability of dual-curing composite core material with different self-etching adhesive systems in a model complete vertical root fracture reconstruction.

PubMed

Waidyasekera, Kanchana; Nikaido, Toru; Weerasinghe, Dinesh; Nurrohman, Hamid; Tagami, Junji

2012-04-01

This study evaluated a dual-curing composite along with different dentin adhesive systems for 1 year under water storage, as a new bonding method of root fragments in complete vertical root fracture. Bovine root fragments were bonded with the dual-curing resin composite Clearfil DC Core Automix (DCA) and one of three adhesive systems: two-step self-etching adhesive Clearfil SE Bond (SE), one-step self-etching adhesive Tokuyama Bond Force (BF), one-step dual-curing self-etching adhesive Clearfil DC Bond (DC). Microtensile bond strength (µTBS)/ultimate tensile bond strength (UTS), FE-SEM ultramorphology of fracture modes, and adhesive dentin interface were observed after water storage for periods of up to one year. The data were analyzed with two-way ANOVA. µTBS was influenced by "dentin adhesive system" (F = 324.455, p < 0.001) and "length of water storage" (F = 8.470, p < 0.001). SE yielded significantly higher µTBS, regardless of storage period (p < 0.05) and maintained the initial µTBS without a significant change after 1 year of water storage (p > 0.05). From 24 h to 1 month, BF showed significantly higher bond strength than DC. UTS of DCA was influenced only by the curing mode of the material (F = 5.051, p = 0.027), but not by the length of water storage (F = 0.053, p > 0.05). Two-step self-etching adhesive systems and dual-curing composite core material can be considered as a suitable bonding method for complete root fractures.

Scapular Stabilization and Muscle Strength in Manual Wheelchair Users with Spinal Cord Injury and Subacromial Impingement.

PubMed

Wilbanks, Susan R; Bickel, C Scott

2016-01-01

Background: Manual wheelchair users with spinal cord injury (SCI) are frequently diagnosed with subacromial impingement. Objective: To determine whether the pattern of muscle imbalance and impaired scapular stabilization in able-bodied (AB) adults with impingement is different from that in manual wheelchair users with SCI and impingement. Methods: The following measurements were collected from 22 adults with subacromial impingement (11 SCI, 11 AB): ratio of normalized muscle electrical activity of upper and lower trapezius (UT:LT) during arm abduction; force during abduction, adduction, internal rotation, external rotation, and push and pull; ratios of force for abduction to adduction (AB:ADD), internal to external rotation (IR:ER), and push to pull (PUSH:PULL). Results: Shoulders with impingement had significantly higher UT:LT activation (1.46 ± 0.52) than shoulders without impingement (0.93 ± 0.45) ( P = .006), regardless of wheelchair user status. Significant differences between AB participants and those with SCI were observed for ABD:ADD ( P = .005), PUSH:PULL ( P = .012), and pull strength ( P = .043). Participants with SCI had a significantly greater ABD:ADD (1.37 ± 0.36) than AB participants (1.04 ± 0.22) ( P = .002) and a significantly greater PUSH:PULL (1.53 ± 0.36) than AB participants (1.26 ± 0.18) ( P = .005) because of decreased strength in adduction ( P = .021) and pull ( P = .013). Conclusions: Strategies targeting the posterior shoulder girdle for AB adults are appropriate for manual wheelchair users with SCI and impingement and should focus on scapular retractors and arm adductors with emphasis on scapular depression and posterior tilting.

Quality assessment of filtered smoked yellowfin tuna (Thunnus albacares) steaks.

PubMed

Pivarnik, Lori F; Faustman, Cameron; Rossi, Santiago; Suman, Surendranath P; Palmer, Catherine; Richard, Nicole L; Ellis, P Christopher; DiLiberti, Michael

2011-08-01

Filtered smoke (FS) has been used to preserve taste, texture, and/or color in tuna and other fish species. This treatment is particularly important in color preservation during frozen storage. The objective of this study was to compare changes in the quality profiles of FS-treated and untreated (UT) yellowfin tuna (Thunnus albacares) steaks stored in 3 ways: room temperature (21 to 22 °C), refrigerated (4 to 5 °C), and iced (0 °C). FS and UT steaks were processed from the same lot of fish and analyzed for chemical, microbiological, lipid oxidation, color, and sensory profiles. Similar trends were seen for microbial proliferation and accumulation of apparent ammonia and total volatile base nitrogen (TVB-N) during the storage temperatures evaluated. Notable exception in quality profile was found in lipid oxidation which was, as expected, lower for treated samples at all storage temperatures for TBARS (P < 0.05) and lower or significantly (P < 0.05) lower for POV values. FS increased the initial redness value significantly (P < 0.05). Unlike UT product, there was no loss of color value concomitant with quality changes for FS-treated tuna for all storage temperatures evaluated. The overall goal of this project was to evaluate filtered smoked tuna steaks as to the impact on the overall quality profile. As a color-stabilizing technology, it could mask deteriorating quality. © 2011 Institute of Food Technologists®

Urea transporter proteins as targets for small-molecule diuretics.

PubMed

Esteva-Font, Cristina; Anderson, Marc O; Verkman, Alan S

2015-02-01

Conventional diuretics such as furosemide and thiazides target salt transporters in kidney tubules, but urea transporters (UTs) have emerged as alternative targets. UTs are a family of transmembrane channels expressed in a variety of mammalian tissues, in particular the kidney. UT knockout mice and humans with UT mutations exhibit reduced maximal urinary osmolality, demonstrating that UTs are necessary for the concentration of urine. Small-molecule screening has identified potent and selective inhibitors of UT-A, the UT protein expressed in renal tubule epithelial cells, and UT-B, the UT protein expressed in vasa recta endothelial cells. Data from UT knockout mice and from rodents administered UT inhibitors support the diuretic action of UT inhibition. The kidney-specific expression of UT-A1, together with high selectivity of the small-molecule inhibitors, means that off-target effects of such small-molecule drugs should be minimal. This Review summarizes the structure, expression and function of UTs, and looks at the evidence supporting the validity of UTs as targets for the development of salt-sparing diuretics with a unique mechanism of action. UT-targeted inhibitors may be useful alone or in combination with conventional diuretics for therapy of various oedemas and hyponatraemias, potentially including those refractory to treatment with current diuretics.

Anti-inflammatory and antioxidant activities of cat's claw (Uncaria tomentosa and Uncaria guianensis) are independent of their alkaloid content.

PubMed

Sandoval, M; Okuhama, N N; Zhang, X J; Condezo, L A; Lao, J; Angeles', F M; Musah, R A; Bobrowski, P; Miller, M J S

2002-05-01

Cat's claw is an herbal medicine from the Amazon that is used widely to treat inflammatory disorders. The purpose of this study was to characterize the antioxidative and antiinflammatory properties of cat's claw, Uncaria tomentosa (UT) and Uncaria guianensis (UG). Alkaloids and flavanols were determined using reversed-phase HPLC; scavenging of 1,1-diphenyl-2-picrilhydrazyl (DPPH), hydroxyl radicals, and lipid peroxidation by spectrophotometry; and TNFalpha production by ELISA. Anti-inflammatory activity was assessed in vitro by inhibition of TNFalpha and nitrite production from RAW 264.7 cells exposed to LPS (50 ng/ml) and in vivo using the indomethacin-induced gastritis model. Apoptosis was assessed using the TUNEL technique and TNFalpha mRNA by in situ RT-PCR. In each of the antioxidant assays tested, UG was more potent than UT (P < 0.01). The total oxindole and pentacyclic alkaloid content of UT was 35-fold > UG. The IC50 value for inhibition of TNFalpha production was significantly (P < 0.01) higher for UT (14.1 ng/ml) vs UG (9.5 ng/ml), yet at concentrations that were considerable lower than that required for antioxidant activity. Non-alkaloid HPLC fractions from UT decreased LPS-induced TNFalpha and nitrite production in RAW 264.7 cells (P < 0.01) at a concentration range comparable to the parent botanical. Oral pretreatment for 3 d with UT protected against indomethacin-induced gastritis, and prevented TNFalpha mRNA expression and apoptosis. These results indicate that while both species of cat's claw provide effective antioxidant and anti-inflammatory activities, U. guianensis is more potent. In conclusion, the presence of oxindole or pentacyclic alkaloids did not influence the antioxidant and anti-inflammatory properties of cat's claw.

Accurate procedure for deriving UTI at a submilliarcsecond accuracy from Greenwich Sidereal Time or from the stellar angle

NASA Astrophysics Data System (ADS)

Capitaine, N.; Gontier, A.-M.

1993-08-01

Present observations using modern astrometric techniques are supposed to provide the Earth orientation parameters, and therefore UT1, with an accuracy better than ±1 mas. In practice, UT1 is determined through the intermediary of Greenwich Sidereal Time (GST), using both the conventional relationship between Greenwich Mean Sidereal Time (GMST) and UTl (Aoki et al. 1982) and the so-called "equation of the equinoxes" limited to the first order terms with respect to the nutation quantities. This highly complex relation between sidereal time and UT1 is not accurate at the milliaresecond level which gives rise to spurious terms of milliaresecond amplitude in the derived UTl. A more complete relationship between GST and UT1 has been recommended by Aoki & Kinoshita (1983) and Aoki (1991) taking into account the second order terms in the difference between GST and GM ST, the largest one having an amplitude of 2.64 mas and a 18.6 yr-period. This paper explains how this complete expansion of GST implicitly uses the concept of "nonrotating origin" (NRO) as proposed by Guinot in 1979 and would, therefore, provide a more accurate value of UTl and consequently of the Earth's angular velocity. This paper shows, moreover, that such a procedure would be simplified and conceptually clarified by the explicit use of the NRO as previously proposed (Guinot 1979; Capitaine et al. 1986). The two corresponding options (implicit or explicit use of the NRO) are shown to be equivalent for defining the specific Earth's angle of rotation and then UT1. The of the use of such an accurate procedure which has been proposed in the new IERS standards (McCarthy 1992a) instead of the usual one are estimated for the practical derivation of UT1.

Configuration and Calibration of High Temperature Furnaces for Testing Ceramic Matrix Composites

DTIC Science & Technology

2014-10-01

Actual Furnace Cavity Stainless Steel Mesh Cage For Electrical Connections (both sides) High Temperature Power Lead Clamp Furnace Control TC’s Power... tests generate the basic properties such as modulus (E), ultimate tensile strength (UTS), proportional limit (PL), strain at failure (f), as well as...stress- strain behavior. Each material was tested at room temperature, at the maximum use temperature for the CMC system (as determined by the CMC

A comparison of LOD and UT1-UTC forecasts by different combined prediction techniques

NASA Astrophysics Data System (ADS)

Kosek, W.; Kalarus, M.; Johnson, T. J.; Wooden, W. H.; McCarthy, D. D.; Popiński, W.

Stochastic prediction techniques including autocovariance, autoregressive, autoregressive moving average, and neural networks were applied to the UT1-UTC and Length of Day (LOD) International Earth Rotation and Reference Systems Servive (IERS) EOPC04 time series to evaluate the capabilities of each method. All known effects such as leap seconds and solid Earth zonal tides were first removed from the observed values of UT1-UTC and LOD. Two combination procedures were applied to predict the resulting LODR time series: 1) the combination of the least-squares (LS) extrapolation with a stochastic predition method, and 2) the combination of the discrete wavelet transform (DWT) filtering and a stochastic prediction method. The results of the combination of the LS extrapolation with different stochastic prediction techniques were compared with the results of the UT1-UTC prediction method currently used by the IERS Rapid Service/Prediction Centre (RS/PC). It was found that the prediction accuracy depends on the starting prediction epochs, and for the combined forecast methods, the mean prediction errors for 1 to about 70 days in the future are of the same order as those of the method used by the IERS RS/PC.

Sex differences in quadrupedal walking gaits of Uner Tan syndrome cases, healthy humans and nonhuman primates.

PubMed

Tan, Uner

2017-03-01

Uner Tan syndrome (UTS) cases with habitual quadrupedal locomotion (QL), impaired intelligence, and dysarthric or no speech predominantly use lateral sequence (LS) gait like nonprimates rather than the predominantly diagonal sequence (DS) gait of nonhuman primates. However, these studies neglected possible sex-related differences in these gait types. (1) To assess the possible sex-related gait types in UTS cases, healthy infants and adults with requested QL, and the nonhuman primates. (2) To test the hypothesis that sex differences may exist in quadrupedal walking gaits in UTS cases, healthy humans, and nonhuman primates. The UTS cases were filmed, the other study groups were taken from public open 'youtube' videos, which were used to assess the walking gait types as DS and LS. The right and left hind-limb phase values were calculated separately for males and females to allow a possible sex difference in walking gaits to be determined. Females predominantly used DS gait, contrary to males with predominantly LS gait. Consistent with the working hypothesis, the results suggested a biological sex-related trend in preferred walking gaits exists in all of the human and nonhuman primates using QL.

Role of thin descending limb urea transport in renal urea handling and the urine concentrating mechanism

PubMed Central

Lei, Tianluo; Zhou, Lei; Layton, Anita T.; Zhou, Hong; Zhao, Xuejian; Bankir, Lise

2011-01-01

Urea transporters UT-A2 and UT-B are expressed in epithelia of thin descending limb of Henle's loop and in descending vasa recta, respectively. To study their role and possible interaction in the context of the urine concentration mechanism, a UT-A2 and UT-B double knockout (UT-A2/B knockout) mouse model was generated by targeted deletion of the UT-A2 promoter in embryonic stem cells with UT-B gene knockout. The UT-A2/B knockout mice lacked detectable UT-A2 and UT-B transcripts and proteins and showed normal survival and growth. Daily urine output was significantly higher in UT-A2/B knockout mice than that in wild-type mice and lower than that in UT-B knockout mice. Urine osmolality in UT-A2/B knockout mice was intermediate between that in UT-B knockout and wild-type mice. The changes in urine osmolality and flow rate, plasma and urine urea concentration, as well as non-urea solute concentration after an acute urea load or chronic changes in protein intake suggested that UT-A2 plays a role in the progressive accumulation of urea in the inner medulla. These results suggest that in wild-type mice UT-A2 facilitates urea absorption by urea efflux from the thin descending limb of short loops of Henle. Moreover, UT-A2 deletion in UT-B knockout mice partially remedies the urine concentrating defect caused by UT-B deletion, by reducing urea loss from the descending limbs to the peripheral circulation; instead, urea is returned to the inner medulla through the loops of Henle and the collecting ducts. PMID:21849488

Role of thin descending limb urea transport in renal urea handling and the urine concentrating mechanism.

PubMed

Lei, Tianluo; Zhou, Lei; Layton, Anita T; Zhou, Hong; Zhao, Xuejian; Bankir, Lise; Yang, Baoxue

2011-12-01

Urea transporters UT-A2 and UT-B are expressed in epithelia of thin descending limb of Henle's loop and in descending vasa recta, respectively. To study their role and possible interaction in the context of the urine concentration mechanism, a UT-A2 and UT-B double knockout (UT-A2/B knockout) mouse model was generated by targeted deletion of the UT-A2 promoter in embryonic stem cells with UT-B gene knockout. The UT-A2/B knockout mice lacked detectable UT-A2 and UT-B transcripts and proteins and showed normal survival and growth. Daily urine output was significantly higher in UT-A2/B knockout mice than that in wild-type mice and lower than that in UT-B knockout mice. Urine osmolality in UT-A2/B knockout mice was intermediate between that in UT-B knockout and wild-type mice. The changes in urine osmolality and flow rate, plasma and urine urea concentration, as well as non-urea solute concentration after an acute urea load or chronic changes in protein intake suggested that UT-A2 plays a role in the progressive accumulation of urea in the inner medulla. These results suggest that in wild-type mice UT-A2 facilitates urea absorption by urea efflux from the thin descending limb of short loops of Henle. Moreover, UT-A2 deletion in UT-B knockout mice partially remedies the urine concentrating defect caused by UT-B deletion, by reducing urea loss from the descending limbs to the peripheral circulation; instead, urea is returned to the inner medulla through the loops of Henle and the collecting ducts.

Growth of surface structures correlated with structural and mechanical modifications of brass by laser-induced Si plasma ions implantation

NASA Astrophysics Data System (ADS)

Ahmad, Shahbaz; Bashir, Shazia; Rafique, M. Shahid; Yousaf, Daniel

2017-04-01

Laser-produced Si plasma is employed as an ion source for implantation on the brass substrate for its surface, structural, and mechanical modifications. Thomson parabola technique is employed for the measurement of energy and flux of Si ions using CR-39. In response to stepwise increase in number of laser pulses from 3000 to 12000, four brass substrates were implanted by laser-induced Si plasma ions of energy 290 keV at different fluxes ranging from 45 × 1012 to 75 × 1015 ions/cm2. SEM analysis reveals the formation of nano/micro-sized irregular shaped cavities and pores for the various ion fluxes for varying numbers of laser pulses from 3000 to 9000. At the maximum ion flux for 12,000 pulses, distinct and organized grains with hexagonal and irregular shaped morphology are revealed. X-ray diffractometer (XRD) analysis exhibits that a new phase of CuSi (311) is identified which confirms the implantation of Si ions in brass substrate. A significant decrease in mechanical properties of implanted brass, such as Yield Stress (YS), Ultimate Tensile Strength (UTS), and hardness, with increasing laser pulses from 3000 to 6000 is observed. However, with increasing laser pulses from 9000 to a maximum value of 12,000, an increase in mechanical properties like hardness, YS, and UTS is observed. The generation as well as annihilation of defects, recrystallization, and intermixing of Si precipitates with brass matrix is considered to be responsible for variations in surface, structural, and mechanical modifications of brass.

Mechanical and microbiological properties and drug release modeling of an etch-and-rinse adhesive containing copper nanoparticles.

PubMed

Gutiérrez, M F; Malaquias, P; Matos, T P; Szesz, A; Souza, S; Bermudez, J; Reis, A; Loguercio, A D; Farago, P V

2017-03-01

To evaluate the effect of addition of copper nanoparticles (CN) at different concentrations into a two-step etch-and-rinse (2-ER) adhesive on antimicrobial activity (AMA), copper release (CR), ultimate tensile strength (UTS), degree of conversion (DC), water sorption (WS), solubility (SO), as well as the immediate (IM) and 1-year resin-dentin bond strength (μTBS) and nanoleakage (NL). Seven adhesives were formulated according to the addition of CN (0, 0.0075, 0.015, 0.06, 0.1, 0.5 and 1wt%) in adhesive. The AMA was evaluated against Streptococcus mutans using agar diffusion assay. For CR, WS and SO, specimens were constructed and tested for 28 days. For UTS, specimens were tested after 24h and 28 days. For DC, specimens were constructed and tested after 24h by FTIR. After enamel removal, the ER was applied to dentin. After composite resin build-ups, specimens were sectioned to obtain resin-dentin sticks. For μTBS and NL, specimens were tested after 24h and 1-year periods. All data were submitted to statistical analysis (α=0.05). The addition of CN provided AMA to the adhesives at all concentrations. Higher CR was observed in adhesives with higher concentration of CN. UTS, DC, WS and SO were not influenced. For μTBS an increase was observed in 0.1 and 0.5% copper group. For NL, a significant decrease was observed in all groups in comparison with control group. After 1-year, no significant reductions of μTBS and no significant increases of NL were observed for copper containing adhesives compared to the control group. The addition of CN in concentrations up to 1wt% in the 2-ER adhesive may be an alternative to provide AMA and preserve the bonding to dentin, without reducing adhesives' mechanical properties evaluated. Copyright © 2016 The Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Genes and proteins of urea transporters.

PubMed

Sands, Jeff M; Blount, Mitsi A

2014-01-01

A urea transporter protein in the kidney was first proposed in 1987. The first urea transporter cDNA was cloned in 1993. The SLC14a urea transporter family contains two major subgroups: SLC14a1, the UT-B urea transporter originally isolated from erythrocytes; and SLC14a2, the UT-A group originally isolated from kidney inner medulla. Slc14a1, the human UT-B gene, arises from a single locus located on chromosome 18q12.1-q21.1, which is located close to Slc14a2. Slc14a1 includes 11 exons, with the coding region extending from exon 4 to exon 11, and is approximately 30 kb in length. The Slc14a2 gene is a very large gene with 24 exons, is approximately 300 kb in length, and encodes 6 different isoforms. Slc14a2 contains two promoter elements: promoter I is located in the typical position, upstream of exon 1, and drives the transcription of UT-A1, UT-A1b, UT-A3, UT-A3b, and UT-A4; while promoter II is located within intron 12 and drives the transcription of UT-A2 and UT-A2b. UT-A1 and UT-A3 are located in the inner medullary collecting duct, UT-A2 in the thin descending limb and liver, UT-A5 in testis, UT-A6 in colon, UT-B1 primarily in descending vasa recta and erythrocytes, and UT-B2 in rumen.

Influence of biocorrosion on microstructure and mechanical properties of deformed Mg-Y-Er-Zn biomaterial containing 18R-LPSO phase.

PubMed

Leng, Zhe; Zhang, Jinghuai; Yin, Tingting; Zhang, Li; Guo, Xuying; Peng, Qiuming; Zhang, Milin; Wu, Ruizhi

2013-12-01

The microstructure and mechanical properties of as-extruded Mg-8Y-1Er-2Zn (wt%) alloy containing long period stacking ordered (LPSO) phase are comparatively investigated before and after corrosion in a simulated body fluid (SBF) at 37°C. The as-extruded alloy consists of a long strip-like 18R-LPSO phase and some fine lamellae grains formed by primary recrystallization during the extrusion process. The hydrogen evolution volume per day fluctuates between 0.21 and 0.32ml/cm(2) in the immersion test for 240h, and the corresponding corrosion rate is calculated as 0.568mm/y. The corrosion product is determined as Mg(OH)2, whilst a Ca(H2PO4)2 compound is also observed on the surface of the samples. The corrosion site preferentially occurs at the interface between LPSO phase and Mg matrix. Before immersing, the tensile yield strength (TYS), ultimate tensile strength (UTS) and elongation of the alloy are 275MPa, 359MPa, and 19%, respectively. More attractively, these mechanical properties can be maintained even after immersing in SBF for 240h (TYS, UTS and elongation are 216MPa, 286MPa and 6.8%, respectively) because of the existence of high anti-corrosion LPSO phase. © 2013 Elsevier Ltd. All rights reserved.

Electromyographic analysis of knee push up plus variations: what is the influence of the kinetic chain on scapular muscle activity?

PubMed

Maenhout, A; Van Praet, K; Pizzi, L; Van Herzeele, M; Cools, A

2010-11-01

First, to look for appropriate closed kinetic chain exercises to restore intramuscular imbalance between upper trapezius (UT) and serratus anterior (SA) in overhead athletes. Second, to determine the influence of using diagonal pattern muscle recruitment during knee push up plus (KPP) exercises on scapular electromyographic activity. Single group repeated-measures design. Controlled laboratory study. Thirty-two physically active individuals in good general health who did not have a history of neck and/or shoulder injury or surgery nor participated in high-level overhead sports or performed upper limb strength training for more than 5 h/week. Interventions Subjects performed the standard KPP and six variations. Electromyographic activity of the three trapezius parts and the SA. Four exercises with a low UT/SA can be selected for rehabilitation of intramuscular balance: standard KPP, KPP with homolateral leg extension, KPP with a wobble board and homolateral leg extension and one-handed KPP. The use of a wobble board during KPP exercises and performance on one hand has no influence on SA electromyographic activity. Heterolateral leg extension during KPP stimulates lower trapezius activity, whereas homolateral leg extension stimulates SA activity. In case of intramuscular scapular imbalance, some exercises are preferable over others because of their low UT/SA ratio. The use of a kinetic chain approach during KPP exercises influences scapular muscle activity.

Structural instability in polyacene: A projector quantum Monte Carlo study

NASA Astrophysics Data System (ADS)

Srinivasan, Bhargavi; Ramasesha, S.

1998-04-01

We have studied polyacene within the Hubbard model to explore the effect of electron correlations on the Peierls' instability in a system marginally away from one dimension. We employ the projector quantum Monte Carlo method to obtain ground-state estimates of the energy and various correlation functions. We find strong similarities between polyacene and polyacetylene which can be rationalized from the real-space valence-bond arguments of Mazumdar and Dixit. Electron correlations tend to enhance the Peierls' instability in polyacene. This enhancement appears to attain a maximum at U/t~3.0, and the maximum shifts to larger values when the alternation parameter is increased. The system shows no tendency to destroy the imposed bond-alternation pattern, as evidenced by the bond-bond correlations. The cis distortion is seen to be favored over the trans distortion. The spin-spin correlations show that undistorted polyacene is susceptible to a spin-density-wave distortion for large interaction strength. The charge-charge correlations indicate the absence of a charge-density-wave distortion for the parameters studied.

Forskolin stimulation promotes urea transporter UT-A1 ubiquitination, endocytosis, and degradation in MDCK cells

PubMed Central

Su, Hua; Carter, Conner B.; Laur, Oskar; Sands, Jeff M.

2012-01-01

The adenylyl cyclase stimulator forskolin (FSK) stimulates UT-A1 phosphorylation, membrane trafficking, and urea transport activity. Here, we found that FSK stimulation induces UT-A1 ubiquitination in UT-A1 Madin-Darby canine kidney (MDCK) cells. This suggests that phosphorylation by FSK also triggers the protein degradation machinery for UT-A1. UT-A1-MDCK cells were treated with 100 μg/ml cycloheximide to inhibit protein synthesis, with or without 10 μM FSK. Total UT-A1 protein abundance was significantly reduced after FSK treatment, concomitantly ubiquitinated UT-A1 was increased. We then specifically investigated the effect of FSK on UT-A1 expressed on the cell plasma membrane. FSK treatment accelerated UT-A1 removal from the cell plasma membrane by increasing UT-A1 endocytosis as judged by biotinylation/MesNa treatment and confocal microscopy. We further found that inhibition of the clathrin-mediated endocytic pathway, but not the caveolin-mediated endocytic pathway, significantly blocks FSK-stimulated UT-A1 endocytosis. The PKA inhibitor H89 and the proteasome inhibitors MG132 and lactacystin reduced FSK-induced membrane UT-A1 reduction. Our study shows that FSK activates the UT-A1 urea transporter and the activation/phosphorylation subsequently triggers the downregulation of UT-A1, which represents an important mechanism for the cell to return to the basal conditions after vasopressin stimulation. PMID:22914781

Mechanical properties and modeling of drug release from chlorhexidine-containing etch-and-rinse adhesives.

PubMed

Stanislawczuk, Rodrigo; Reis, Alessandra; Malaquias, Pamela; Pereira, Fabiane; Farago, Paulo Vitor; Meier, Marcia Margarete; Loguercio, Alessandro D

2014-04-01

To evaluate the effects of chlorhexidine (CHX) addition in different concentrations into simplified etch-and-rinse adhesives on the ultimate tensile strength (UTS), water sorption (WS), solubility (SO) and the rate of CHX release over time. We added CHX diacetate to Ambar [AM] (FGM) and XP Bond [XP] (Dentsply) in concentrations of 0, 0.01, 0.05, 0.1 and 0.2 wt%. For UTS (n=10 for each group), adhesive specimens were constructed in an hourglass shape metallic matrix with cross-sectional area of 0.8 mm(2). Half of specimens were tested after 24 h and the other half after 28 days of water storage in tension of 0.5 mm/min. For WS and SO (n=10 for each group), adhesive discs (5.8 mm×1.0 mm) were prepared into a mold. After desiccation, we weighed and stored the cured adhesive specimens in distilled water for evaluation of the WS, SO and the cumulative release of CHX over a 28-day period. For CHX release (n=10 for each group), spectrophotometric measurements of storage solution were performed to examine the release kinetics of CHX. We subjected data from each test to ANOVA and Tukey' test (α=0.05). XP Bond adhesive showed significantly more WS and SO and lower UTS than Ambar. In general, the addition of CHX did not alter WS, SO and UTS of the adhesives. XP showed a higher CHX release than AM (p<0.05) in all concentrations and the final amount of CHX release was directly proportional to the initial CHX concentration added to the adhesives. After 28 days of water storage, approximately 20% of CHX was released from XP and 8.0-12.0% from AM. Addition of CHX to commercial adhesive is a feasible method to provide a controlled release of CHX over time without jeopardizing WS, SO and UTS of the adhesives. Manufacturers should consider adding CHX to commercial adhesives to provide a controlled release of CHX over time. Copyright © 2014 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Modulation of kidney urea transporter UT-A3 activity by alpha2,6-sialylation

PubMed Central

Qian, Xiaoqian; Sands, Jeff M.; Song, Xiang; Chen, Guangping

2016-01-01

Two urea transporters, UT-A1 and UT-A3, are expressed in the kidney terminal inner medullary collecting duct (IMCD) and are important for the production of concentrated urine. UT-A1, as the largest isoform of all UT-A urea transporters, has gained much attention and been extensively studied; however the role and the regulation of UT-A3 are less explored. In this study, we investigated UT-A3 regulation by glycosylation modification. A site-directed mutagenesis verified a single glycosylation site in UT-A3 at Asn279. Loss of the glycosylation reduced forskolin-stimulated UT-A3 cell membrane expression and urea transport activity. UT-A3 has two glycosylation forms, 45 kDa and 65 kDa. Using sugar specific-binding lectins, the UT-A3 glycosylation profile was examined. The 45 kDa form was pulled down by lectin Con A and GNL, indicating an immature glycan with a high amount of mannose (Man); whereas the 65 kDa form is a mature glycan composed of acetylglucosamine (GlcNAc), poly-N-acetyllactosame (poly-LacNAc) that was pulled down by WGA and tomato lectin, respectively. Interestingly, the mature form of UT-A3 glycan contains significant amounts of sialic acid. We explored the enzymes responsible for directing UT-A3 sialylation. Sialyltransferase ST6GalI, but not ST3GalIV, catabolizes UT-A3 α2, 6-sialylation. Activation of PKC by PDB treatment promoted UT-A3 glycan sialylation and membrane surface expression. PKC inhibitor chelerythrine blocks ST6GalI-induced UT-A3 sialylation. Increased sialylation by ST6GalI increased UT-A3 protein stability and urea transport activity. Collectively, our study reveals a novel mechanism of UT-A3 regulation by ST6GalI-mediated sialylation modification that may play an important in kidney urea reabsorption and the urinary concentrating mechanism. PMID:26972907

Urea Transport and Clinical Potential of Urearetics

PubMed Central

Klein, Janet D.; Sands, Jeff M.

2016-01-01

Purpose of review Urea is transported by urea transporter proteins in kidney, erythrocytes, and other tissues. Mice in which different urea transporters have been knocked-out have urine concentrating defects, which has led to the development and testing of UT-A and UT-B inhibitors as urearetics. This review summarizes the knowledge gained during the past year on urea transporter regulation and investigations into the clinical potential of urearetics. Recent findings UT-A1 undergoes several post-translational modifications that increase its function by increasing UT-A1 accumulation in the apical plasma membrane. UT-A1 is phosphorylated by PKA, Epac, PKCα, and AMPK, all at different serine residues. UT-A1 is also regulated by 14-3-3, which contributes to UT-A1 removal from the membrane. UT-A1 is glycosylated with various glycan moieties in animal models of diabetes mellitus. Transgenic expression of UT-A1 into UT-A1/UT-A3 knock-out mice restores urine concentrating ability. UT-B is present in descending vasa recta and urinary bladder, and is linked to bladder cancer. Inhibitors of UT-A and UT-B have been developed that result in diuresis with fewer abnormalities in serum electrolytes than conventional diuretics. Summary Urea transporters play critical roles in the urine concentrating mechanism. Urea transport inhibitors are a promising new class of diuretic agents. PMID:27367911

Grain Refinement of Al-Si Hypoeutectic Alloys by Al3Ti1B Master Alloy and Ultrasonic Treatment

NASA Astrophysics Data System (ADS)

Wang, Gui; Wang, Eric Qiang; Prasad, Arvind; Dargusch, Matthew; StJohn, David H.

Al-Si alloys are widely used in automotive and aerospace industries due to their excellent castability, high strength to weight ratio and good corrosion resistance. However, Si poisoning severely limits the degree of grain refinement with the grain size becoming larger as the Si content increases. Generally the effect of Si poisoning is reduced by increasing the amount of master alloy added to the melt during casting. However, an alternative approach is physical grain refinement through the application of an external force (e.g. mechanical or electromagnetic stirring, intensive shearing and ultrasonic irradiation). This work compares the grain refining efficiency of three approaches to the grain refinement of a range of hypoeutectic Al-Si alloys by (i) the addition of A13Ti1B master alloy, (ii) the application of Ultrasonic Treatment (UT) and (iii) the combined addition of A13Ti1B master alloy and the application of UT.

Developing Hypothetical Inhibition Mechanism of Novel Urea Transporter B Inhibitor

NASA Astrophysics Data System (ADS)

Li, Min; Tou, Weng Ieong; Zhou, Hong; Li, Fei; Ren, Huiwen; Chen, Calvin Yu-Chian; Yang, Baoxue

2014-07-01

Urea transporter B (UT-B) is a membrane channel protein that specifically transports urea. UT-B null mouse exhibited urea selective urine concentrating ability deficiency, which suggests the potential clinical applications of the UT-B inhibitors as novel diuretics. Primary high-throughput virtual screening (HTVS) of 50000 small-molecular drug-like compounds identified 2319 hit compounds. These 2319 compounds were screened by high-throughput screening using an erythrocyte osmotic lysis assay. Based on the pharmacological data, putative UT-B binding sites were identified by structure-based drug design and validated by ligand-based and QSAR model. Additionally, UT-B structural and functional characteristics under inhibitors treated and untreated conditions were simulated by molecular dynamics (MD). As the result, we identified four classes of compounds with UT-B inhibitory activity and predicted a human UT-B model, based on which computative binding sites were identified and validated. A novel potential mechanism of UT-B inhibitory activity was discovered by comparing UT-B from different species. Results suggest residue PHE198 in rat and mouse UT-B might block the inhibitor migration pathway. Inhibitory mechanisms of UT-B inhibitors and the functions of key residues in UT-B were proposed. The binding site analysis provides a structural basis for lead identification and optimization of UT-B inhibitors.

Microstructures, Mechanical Properties, and Strain Hardening Behavior of an Ultrahigh Strength Dual Phase Steel Developed by Intercritical Annealing of Cold-Rolled Ferrite/Martensite

NASA Astrophysics Data System (ADS)

Mazaheri, Y.; Kermanpur, A.; Najafizadeh, A.

2015-07-01

A dual phase (DP) steel was produced by a new process utilizing an uncommon cold-rolling and subsequent intercritical annealing of a martensite-ferrite duplex starting structure. Ultrafine grained DP steels with an average grain size of about 2 μm and chain-networked martensite islands were achieved by short intercritical annealing of the 80 pct cold-rolled duplex microstructure. The strength of the low carbon steel with the new DP microstructure was reached about 1300 MPa (140 pct higher than that of the as-received state, e.g., 540 MPa), without loss of ductility. Tensile testing revealed good strength-elongation balance for the new DP steels (UTS × UE ≈ 11,000 to 15,000 MPa pct) in comparison with the previous works and commercially used high strength DP steels. Two strain hardening stages with comparable exponents were observed in the Holloman analysis of all DP steels. The variations of hardness, strength, elongation, and strain hardening behavior of the specimens with thermomechanical parameters were correlated to microstructural features.

Small-Molecule Inhibitors of Urea Transporters

PubMed Central

Verkman, Alan S.; Esteva-Font, Cristina; Cil, Onur; Anderson, Marc O.; Li, Fei; Li, Min; Lei, Tianluo; Ren, Huiwen; Yang, Baoxue

2015-01-01

Urea transporter (UT) proteins, which include isoforms of UT-A in kidney tubule epithelia and UT-B in vasa recta endothelia and erythrocytes, facilitate urinary concentrating function. Inhibitors of urea transporter function have potential clinical applications as sodium-sparing diuretics, or ‘urearetics,’ in edema from different etiologies, such as congestive heart failure and cirrhosis, as well as in syndrome of inappropriate antidiuretic hormone (SIADH). High-throughput screening of drug-like small molecules has identified UT-A and UT-B inhibitors with nanomolar potency. Inhibitors have been identified with different UT-A versus UT-B selectivity profiles and putative binding sites on UT proteins. Studies in rodent models support the utility of UT inhibitors in reducing urinary concentration, though testing in clinically relevant animal models of edema has not yet been done. PMID:25298345

Urea transport and clinical potential of urearetics.

PubMed

Klein, Janet D; Sands, Jeff M

2016-09-01

Urea is transported by urea transporter proteins in kidney, erythrocytes, and other tissues. Mice in which different urea transporters have been knocked out have urine-concentrating defects, which has led to the development and testing of urea transporters Slc14A2 (UT-A) and Slc14A1 (UT-B) inhibitors as urearetics. This review summarizes the knowledge gained during the past year on urea transporter regulation and investigations into the clinical potential of urearetics. UT-A1 undergoes several posttranslational modifications that increase its function by increasing UT-A1 accumulation in the apical plasma membrane. UT-A1 is phosphorylated by protein kinase A, exchange protein activated by cyclic AMP, protein kinase Cα, and AMP-activated protein kinase, all at different serine residues. UT-A1 is also regulated by 14-3-3, which contributes to UT-A1 removal from the membrane. UT-A1 is glycosylated with various glycan moieties in animal models of diabetes mellitus. Transgenic expression of UT-A1 into UT-A1/UT-A3 knockout mice restores urine-concentrating ability. UT-B is present in descending vasa recta and urinary bladder, and is linked to bladder cancer. Inhibitors of UT-A and UT-B have been developed that result in diuresis with fewer abnormalities in serum electrolytes than conventional diuretics. Urea transporters play critical roles in the urine-concentrating mechanism. Urea transport inhibitors are a promising new class of diuretic agent.

Effects of aging on mechanical properties of sternocleidomastoid and trapezius muscles during transition from lying to sitting position-A cross-sectional study.

PubMed

Kocur, Piotr; Grzeskowiak, Marcin; Wiernicka, Marzena; Goliwas, Magdalena; Lewandowski, Jacek; Łochyński, Dawid

The aim of this study was to analyze the effects of aging on the viscoelastic properties of the upper trapezius (UT) and the sternocleidomastoid (SCM) muscle during transition from lying to sitting position. The study included 39 older (mean age 67±5.9years) and 36 younger (21.1±1.8years) women. Tone, stiffness and elasticity of the UT and the SCM were measured by means of myotonometry (MyotonPRO) in lying and then, in sitting position. The results were compared using two-way analysis of variance. Irrespective of the position, older women presented with significantly higher muscle tone, stiffness and elasticity than younger subjects (P<0.05). In both groups, the transition from lying to sitting position resulted in a decrease (P<0.05) in the tone and stiffness, but not the elasticity (P>0.05) of the SCM, and stimulated an increase in the tone, stiffness and elasticity of the UT (P<0.05). The degree of changes in both study groups was similar, except from the absolute value of the UT elasticity, significantly higher increase in older women than in younger subjects (P<0.05). Age contributes to an increase in the stiffness and tone of the UT and the SCM, as well as to a decrease in the elasticity of these muscles in female subjects. In contrast, age exerts only a slight effect on the mechanical properties of both muscles during transition from lying to sitting position. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Modulation of kidney urea transporter UT-A3 activity by alpha2,6-sialylation.

PubMed

Qian, Xiaoqian; Sands, Jeff M; Song, Xiang; Chen, Guangping

2016-07-01

Two urea transporters, UT-A1 and UT-A3, are expressed in the kidney terminal inner medullary collecting duct (IMCD) and are important for the production of concentrated urine. UT-A1, as the largest isoform of all UT-A urea transporters, has gained much attention and been extensively studied; however, the role and the regulation of UT-A3 are less explored. In this study, we investigated UT-A3 regulation by glycosylation modification. A site-directed mutagenesis verified a single glycosylation site in UT-A3 at Asn279. Loss of the glycosylation reduced forskolin-stimulated UT-A3 cell membrane expression and urea transport activity. UT-A3 has two glycosylation forms, 45 and 65 kDa. Using sugar-specific binding lectins, the UT-A3 glycosylation profile was examined. The 45-kDa form was pulled down by lectin concanavalin A (Con A) and Galant husnivalis lectin (GNL), indicating an immature glycan with a high amount of mannose (Man), whereas the 65-kDa form is a mature glycan composed of acetylglucosamine (GlcNAc) and poly-N-acetyllactosame (poly-LacNAc) that was pulled down by wheat germ agglutinin (WGA) and tomato lectin, respectively. Interestingly, the mature form of UT-A3 glycan contains significant amounts of sialic acid. We explored the enzymes responsible for directing UT-A3 sialylation. Sialyltransferase ST6GalI, but not ST3GalIV, catabolizes UT-A3 α2,6-sialylation. Activation of protein kinase C (PKC) by PDB treatment promoted UT-A3 glycan sialylation and membrane surface expression. The PKC inhibitor chelerythrine blocks ST6GalI-induced UT-A3 sialylation. Increased sialylation by ST6GalI increased UT-A3 protein stability and urea transport activity. Collectively, our study reveals a novel mechanism of UT-A3 regulation by ST6GalI-mediated sialylation modification that may play an important role in kidney urea reabsorption and the urinary concentrating mechanism.

Fabrication of Carbon Nanofibers/A356 Nanocomposites by High-Intensity Ultrasonic Processing

NASA Astrophysics Data System (ADS)

Wu, Qing-Jie; Yan, Hong

2018-03-01

A356 alloy reinforced with carbon nanofibers (CNFs) was fabricated by high-intensity ultrasonic vibration processing. The microstructure and mechanical properties were investigated. The distribution of CNFs became more and more uniform with the increase of ultrasonic power, and the mechanical properties of nanocomposites were significantly enhanced accordingly. The yield strength (YS), ultimate tensile strength (UTS), and microhardness of the nanocomposite increased by 38.3, 21.9, and 43.2 pct, respectively, at a CNF content of 0.9 wt pct compared with the matrix without CNF addition. The improvement in mechanical properties was the effect of CNFs on the thermal expansion mismatch strengthening of the nanocomposite, the grain refinement of the nanocomposite, and the load transfer from the matrix to the nanofibers.

Fabrication of Carbon Nanofibers/A356 Nanocomposites by High-Intensity Ultrasonic Processing

NASA Astrophysics Data System (ADS)

Wu, Qing-Jie; Yan, Hong

2018-06-01

A356 alloy reinforced with carbon nanofibers (CNFs) was fabricated by high-intensity ultrasonic vibration processing. The microstructure and mechanical properties were investigated. The distribution of CNFs became more and more uniform with the increase of ultrasonic power, and the mechanical properties of nanocomposites were significantly enhanced accordingly. The yield strength (YS), ultimate tensile strength (UTS), and microhardness of the nanocomposite increased by 38.3, 21.9, and 43.2 pct, respectively, at a CNF content of 0.9 wt pct compared with the matrix without CNF addition. The improvement in mechanical properties was the effect of CNFs on the thermal expansion mismatch strengthening of the nanocomposite, the grain refinement of the nanocomposite, and the load transfer from the matrix to the nanofibers.

Processing of Aluminum-Graphite Particulate Metal Matrix Composites by Advanced Shear Technology

NASA Astrophysics Data System (ADS)

Barekar, N.; Tzamtzis, S.; Dhindaw, B. K.; Patel, J.; Hari Babu, N.; Fan, Z.

2009-12-01

To extend the possibilities of using aluminum/graphite composites as structural materials, a novel process is developed. The conventional methods often produce agglomerated structures exhibiting lower strength and ductility. To overcome the cohesive force of the agglomerates, a melt conditioned high-pressure die casting (MC-HPDC) process innovatively adapts the well-established, high-shear dispersive mixing action of a twin screw mechanism. The distribution of particles and properties of composites are quantitatively evaluated. The adopted rheo process significantly improved the distribution of the reinforcement in the matrix with a strong interfacial bond between the two. A good combination of improved ultimate tensile strength (UTS) and tensile elongation (ɛ) is obtained compared with composites produced by conventional processes.

Regulation of Urea Transporters by Tonicity-responsive Enhancer Binding Protein

PubMed Central

Kwon, H. Moo; Kim, Jim

2007-01-01

Urea accumulation in the renal inner medulla plays a key role in the maintenance of maximal urinary concentrating ability. Urea transport in the kidney is mediated by transporter proteins that include renal urea transporter (UT-A) and erythrocyte urea transporter (UT-B). UT-A1 and UT-A2 are produced from the same gene. There is an active tonicity-responsive enhancer (TonE) in the promoter of UT-A1, and the UT-A1 promoter is stimulated by hypertonicity via tonicity-responsive enhancer binding protein (TonEBP). The downregulation of UT-A2 raises the possibility that TonEBP also regulates its promoter. There is some evidence that TonEBP regulates expression of UT-A in vivo; (1) during the renal development of the urinary concentrating ability, expression of TonEBP precedes that of UT-A1; (2) in transgenic mice expressing a dominant negative form of TonEBP, expression of UT-A1 and UT-A2 is severely impaired; (3) in treatment with cyclosporine A, TonEBP was significantly downregulated after 28 days. This downregulation involves mRNA levels of UT-A2; (4) in hypokalemic animals, downregulation of TonEBP contributed to the down regulation of UT-A in the inner medulla. These data support that TonEBP directly contributes to the urinary concentration and renal urea recycling by the regulation of urea transporters. PMID:24459497

Effect of Annealing on Microstructure, Texture and Tensile Properties of Twin-Roll Cast AZ31B

NASA Astrophysics Data System (ADS)

Masoumi, Mohsen; Zarandi, Faramarz; Pekguleryuz, Mihriban O.

Twin-roll cast (TRC) AZ31 alloy (Mg-3wt.%Al-1wt.%Zn) was subjected to heat treatment at 420 °C. As a result, the intensity of the original basal texture was reduced considerably. Crystallographic orientation analysis revealed that such a change in the texture is due to particle-stimulated nucleation of new grains with random orientations. The tensile test results indicate that annealing slightly increases ultimate tensile strength (UTS), however, dramatically improves the elongation.

View of the cinder block milking barn (UT126D) and attached ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View of the cinder block milking barn (UT-126-D) and attached livestock barn (UT-126-B) with large barn (UT-126-A) in the foreground, looking east-northeast - Thomas Powers Ranch, Milking Barn, 4137 North Highway 224, Snyderville, Summit County, UT

Hot Press as a Sustainable Direct Recycling Technique of Aluminium: Mechanical Properties and Surface Integrity

PubMed Central

Lajis, Mohd Amri; Ahmad, Azlan

2017-01-01

Meltless recycling technique has been utilized to overcome the lack of primary resources, focusing on reducing the usage of energy and materials. Hot press was proposed as a novel direct recycling technique which results in astoundingly low energy usage in contrast with conventional recycling. The aim of this study is to prove the technical feasibility of this approach by characterizing the recycled samples. For this purpose, AA6061 aluminium chips were recycled by utilizing hot press process under various operating temperature (Ts = 430, 480, and 530 °C) and holding times (ts = 60, 90, and 120 min). The maximum mechanical properties of recycled chip are Ultimate tensile strength (UTS) = 266.78 MPa, Elongation to failure (ETF) = 16.129%, while, for surface integrity of the chips, the calculated microhardness is 81.744 HV, exhibited at Ts = 530 °C and ts = 120 min. It is comparable to theoretical AA6061 T4-temper where maximum UTS and microhardness is increased up to 9.27% and 20.48%, respectively. As the desired mechanical properties of forgings can only be obtained by means of a final heat treatment, T5-temper, aging after forging process was employed. Heat treated recycled billet AA6061 (T5-temper) are considered comparable with as-received AA6061 T6, where the value of microhardness (98.649 HV) at 175 °C and 120 min of aging condition was revealed to be greater than 3.18%. Although it is quite early to put a base mainly on the observations in experimental settings, the potential for significant improvement offered by the direct recycling methods for production aluminium scrap can be clearly demonstrated. This overtures perspectives for industrial development of solid state recycling processes as environmentally benign alternatives of current melting based practices. PMID:28771207

Earth’s Rotational Deceleration: Determination of Tidal Friction Independent of Timescales

NASA Astrophysics Data System (ADS)

Deines, Steven D.; Williams, Carol A.

2016-04-01

This paper determines Earth's rotational deceleration without relying on atomic or ephemeris timescales. Earth's rotation defines the civil time standard called Universal Time (UT). Our previous paper did not examine tidal friction in depth when analyzing the timescale divergence between UT and International Atomic Time (TAI). We examine all available paleontological fossils and deposits for the direct measurements of Earth's past rotation rates, because that record includes all contributing effects. We examine paleontological reports that date Earth's rotation rate using corals, bivalves, brachiopods, rhythmites, and stromatolites. Contributions that vary Earth's moment of inertia, such as continental plate drifts, coastline changes, ice age formations, and viscous glacial rebounds, are superimposed with the secular deceleration. The average deceleration of Earth's rotation rate from all available fossil data is found to be (5.969 ± 1.762) × 10-7 rad yr-2. Our value is 99.8% of the total rotational deceleration determined by Christodoulidis et al., who used artificial satellite data, and our value is 96.6% of the expected tidal friction value obtained by Stephenson and Morrison. Taking the derivative of conserved angular momentum, the predicted lunar orbital deceleration caused by the average rotational deceleration corresponds closely to lunar models. When evaluating the significant time gaps between UT and TAI, Earth's rotational deceleration is a minor contributing factor. Also, the secular deceleration rate is necessary to correctly date ancient astronomical events. We strongly encourage that more ocean paleontological evidence be found to supplement the record to separate the many periodic variations embedded in these data.

Serotyping reanalysis of unserotypable Actinobacillus pleuropneumoniae isolates by agar gel diffusion test.

PubMed

Morioka, Ayako; Shimazaki, Yoko; Uchiyama, Mariko; Suzuki, Shoko

2016-05-03

We observed increasing unserotypable (UT) Actinobacillus pleuropneumoniae isolates using agar gel diffusion (AGD) test. To reanalyze their serovar, we performed rapid slide agglutination (RSA) test and multiplex PCR for 47 UT isolates. Of these, 25 were serovar 1 (UT-serovar 1), 20 were serovar 2 (UT-serovar 2) and 2 were serovar 15 (UT-serovar 15). We examined serotyping antigen extraction temperature to determine heat influence. UT-serovar 1 and 15 were influenced by heat, because their precipitation lines were observed in the case of low antigen extraction temperature. To investigate the relationship between antigenicity and genotype, we performed pulsed-field gel electrophoresis (PFGE) analysis using UT-serovar 2 and 15. The predominant PFGE pattern of UT-serovar 2 was identical to that of serovar 2.

Serotyping reanalysis of unserotypable Actinobacillus pleuropneumoniae isolates by agar gel diffusion test

PubMed Central

MORIOKA, Ayako; SHIMAZAKI, Yoko; UCHIYAMA, Mariko; SUZUKI, Shoko

2016-01-01

We observed increasing unserotypable (UT) Actinobacillus pleuropneumoniae isolates using agar gel diffusion (AGD) test. To reanalyze their serovar, we performed rapid slide agglutination (RSA) test and multiplex PCR for 47 UT isolates. Of these, 25 were serovar 1 (UT-serovar 1), 20 were serovar 2 (UT-serovar 2) and 2 were serovar 15 (UT-serovar 15). We examined serotyping antigen extraction temperature to determine heat influence. UT-serovar 1 and 15 were influenced by heat, because their precipitation lines were observed in the case of low antigen extraction temperature. To investigate the relationship between antigenicity and genotype, we performed pulsed-field gel electrophoresis (PFGE) analysis using UT-serovar 2 and 15. The predominant PFGE pattern of UT-serovar 2 was identical to that of serovar 2. PMID:26726101

Clustered lot quality assurance sampling to assess immunisation coverage: increasing rapidity and maintaining precision.

PubMed

Pezzoli, Lorenzo; Andrews, Nick; Ronveaux, Olivier

2010-05-01

Vaccination programmes targeting disease elimination aim to achieve very high coverage levels (e.g. 95%). We calculated the precision of different clustered lot quality assurance sampling (LQAS) designs in computer-simulated surveys to provide local health officers in the field with preset LQAS plans to simply and rapidly assess programmes with high coverage targets. We calculated sample size (N), decision value (d) and misclassification errors (alpha and beta) of several LQAS plans by running 10 000 simulations. We kept the upper coverage threshold (UT) at 90% or 95% and decreased the lower threshold (LT) progressively by 5%. We measured the proportion of simulations with < or =d individuals unvaccinated or lower if the coverage was set at the UT (pUT) to calculate beta (1-pUT) and the proportion of simulations with >d unvaccinated individuals if the coverage was LT% (pLT) to calculate alpha (1-pLT). We divided N in clusters (between 5 and 10) and recalculated the errors hypothesising that the coverage would vary in the clusters according to a binomial distribution with preset standard deviations of 0.05 and 0.1 from the mean lot coverage. We selected the plans fulfilling these criteria: alpha < or = 5% beta < or = 20% in the unclustered design; alpha < or = 10% beta < or = 25% when the lots were divided in five clusters. When the interval between UT and LT was larger than 10% (e.g. 15%), we were able to select precise LQAS plans dividing the lot in five clusters with N = 50 (5 x 10) and d = 4 to evaluate programmes with 95% coverage target and d = 7 to evaluate programmes with 90% target. These plans will considerably increase the feasibility and the rapidity of conducting the LQAS in the field.

Placental size and the prediction of severe early-onset intrauterine growth restriction in women with low pregnancy-associated plasma protein-A.

PubMed

Proctor, L K; Toal, M; Keating, S; Chitayat, D; Okun, N; Windrim, R C; Smith, G C S; Kingdom, J C P

2009-09-01

Screening studies for trisomy 21 demonstrate that low maternal serum pregnancy-associated plasma protein-A (PAPP-A) at 11-13 weeks' gestation is associated with stillbirth, intrauterine growth restriction (IUGR) and pre-eclampsia in chromosomally normal fetuses. However, the strength of these associations is too weak to justify screening for these placental insufficiency syndromes. Our objective was to evaluate placental size and uterine artery (UtA) Doppler imaging as second-stage screening tests for women with low PAPP-A. We prospectively studied 90 normal singleton pregnancies with first-trimester PAPP-A

Urea transporter UT-B deletion induces DNA damage and apoptosis in mouse bladder urothelium.

PubMed

Dong, Zixun; Ran, Jianhua; Zhou, Hong; Chen, Jihui; Lei, Tianluo; Wang, Weiling; Sun, Yi; Lin, Guiting; Bankir, Lise; Yang, Baoxue

2013-01-01

Previous studies found that urea transporter UT-B is abundantly expressed in bladder urothelium. However, the dynamic role of UT-B in bladder urothelial cells remains unclear. The objective of this study is to evaluate the physiological roles of UT-B in bladder urothelium using UT-B knockout mouse model and T24 cell line. Urea and NO measurement, mRNA expression micro-array analysis, light and transmission electron microscopy, apoptosis assays, DNA damage and repair determination, and intracellular signaling examination were performed in UT-B null bladders vs wild-type bladders and in vitro T24 epithelial cells. UT-B was highly expressed in mouse bladder urothelium. The genes, Dcaf11, MCM2-4, Uch-L1, Bnip3 and 45 S pre rRNA, related to DNA damage and apoptosis were significantly regulated in UT-B null urothelium. DNA damage and apoptosis highly occurred in UT-B null urothelium. Urea and NO levels were significantly higher in UT-B null urothelium than that in wild-type, which may affect L-arginine metabolism and the intracellular signals related to DNA damage and apoptosis. These findings were consistent with the in vitro study in T24 cells that, after urea loading, exhibited cell cycle delay and apoptosis. UT-B may play an important role in protecting bladder urothelium by balancing intracellular urea concentration. Disruption of UT-B function induces DNA damage and apoptosis in bladder, which can result in bladder disorders.

Thienoquinolins exert diuresis by strongly inhibiting UT-A urea transporters

PubMed Central

Ren, Huiwen; Wang, Yanhua; Xing, Yongning; Ran, Jianhua; Liu, Ming; Lei, Tianluo; Zhou, Hong; Li, Runtao; Sands, Jeff M.

2014-01-01

Urea transporters (UT) play an important role in the urine concentration mechanism by mediating intrarenal urea recycling, suggesting that UT inhibitors could have therapeutic use as a novel class of diuretic. Recently, we found a thienoquinolin UT inhibitor, PU-14, that exhibited diuretic activity. The purpose of this study was to identify more potent UT inhibitors that strongly inhibit UT-A isoforms in the inner medullary collecting duct (IMCD). Efficient thienoquinolin UT inhibitors were identified by structure-activity relationship analysis. Urea transport inhibition activity was assayed in perfused rat terminal IMCDs. Diuretic activity of the compound was determined in rats and mice using metabolic cages. The results show that the compound PU-48 exhibited potent UT-A inhibition activity. The inhibition was 69.5% with an IC50 of 0.32 μM. PU-48 significantly inhibited urea transport in perfused rat terminal IMCDs. PU-48 caused significant diuresis in UT-B null mice, which indicates that UT-A is the target of PU-48. The diuresis caused by PU-48 did not change blood Na+, K+, or Cl− levels or nonurea solute excretion in rats and mice. No toxicity was detected in cells or animals treated with PU-48. The results indicate that thienoquinolin UT inhibitors induce a diuresis by inhibiting UT-A in the IMCD. This suggests that they may have the potential to be developed as a novel class of diuretics with fewer side effects than classical diuretics. PMID:25298523

Thienoquinolins exert diuresis by strongly inhibiting UT-A urea transporters.

PubMed

Ren, Huiwen; Wang, Yanhua; Xing, Yongning; Ran, Jianhua; Liu, Ming; Lei, Tianluo; Zhou, Hong; Li, Runtao; Sands, Jeff M; Yang, Baoxue

2014-12-15

Urea transporters (UT) play an important role in the urine concentration mechanism by mediating intrarenal urea recycling, suggesting that UT inhibitors could have therapeutic use as a novel class of diuretic. Recently, we found a thienoquinolin UT inhibitor, PU-14, that exhibited diuretic activity. The purpose of this study was to identify more potent UT inhibitors that strongly inhibit UT-A isoforms in the inner medullary collecting duct (IMCD). Efficient thienoquinolin UT inhibitors were identified by structure-activity relationship analysis. Urea transport inhibition activity was assayed in perfused rat terminal IMCDs. Diuretic activity of the compound was determined in rats and mice using metabolic cages. The results show that the compound PU-48 exhibited potent UT-A inhibition activity. The inhibition was 69.5% with an IC50 of 0.32 μM. PU-48 significantly inhibited urea transport in perfused rat terminal IMCDs. PU-48 caused significant diuresis in UT-B null mice, which indicates that UT-A is the target of PU-48. The diuresis caused by PU-48 did not change blood Na(+), K(+), or Cl(-) levels or nonurea solute excretion in rats and mice. No toxicity was detected in cells or animals treated with PU-48. The results indicate that thienoquinolin UT inhibitors induce a diuresis by inhibiting UT-A in the IMCD. This suggests that they may have the potential to be developed as a novel class of diuretics with fewer side effects than classical diuretics. Copyright © 2014 the American Physiological Society.

Urea Transporter UT-B Deletion Induces DNA Damage and Apoptosis in Mouse Bladder Urothelium

PubMed Central

Zhou, Hong; Chen, Jihui; Lei, Tianluo; Wang, Weiling; Sun, Yi; Lin, Guiting; Bankir, Lise; Yang, Baoxue

2013-01-01

Background Previous studies found that urea transporter UT-B is abundantly expressed in bladder urothelium. However, the dynamic role of UT-B in bladder urothelial cells remains unclear. The objective of this study is to evaluate the physiological roles of UT-B in bladder urothelium using UT-B knockout mouse model and T24 cell line. Methodology/Principal Findings Urea and NO measurement, mRNA expression micro-array analysis, light and transmission electron microscopy, apoptosis assays, DNA damage and repair determination, and intracellular signaling examination were performed in UT-B null bladders vs wild-type bladders and in vitro T24 epithelial cells. UT-B was highly expressed in mouse bladder urothelium. The genes, Dcaf11, MCM2-4, Uch-L1, Bnip3 and 45 S pre rRNA, related to DNA damage and apoptosis were significantly regulated in UT-B null urothelium. DNA damage and apoptosis highly occurred in UT-B null urothelium. Urea and NO levels were significantly higher in UT-B null urothelium than that in wild-type, which may affect L-arginine metabolism and the intracellular signals related to DNA damage and apoptosis. These findings were consistent with the in vitro study in T24 cells that, after urea loading, exhibited cell cycle delay and apoptosis. Conclusions/Significance UT-B may play an important role in protecting bladder urothelium by balancing intracellular urea concentration. Disruption of UT-B function induces DNA damage and apoptosis in bladder, which can result in bladder disorders. PMID:24204711

Objective assessment of surgical training in flexor tendon repair: the utility of a low-cost porcine model as demonstrated by a single-subject research design.

PubMed

Zetlitz, Elisabeth; Wearing, Scott Cameron; Nicol, Alexander; Hart, Andrew Mackay

2012-01-01

This study evaluated the utility of a porcine flexor tendon model and standard biomechanical testing procedures to quantify the acquisition of surgical skills associated with Zone II flexor tendon repair in a trainee by benchmarking task performance outcomes relative to evidence-based standards. Single-subject repeated measures research design. Bench-top set-up of apparatus undertaken in a University Research laboratory. After initial directed learning, a trainee repaired 70 fresh flexor digitorum profundus tendons within the flexor sheath using either a Pennington or ventral-locking-loop modification of a two-strand Kessler core repair. Tendon repairs were then preconditioned and distracted to failure. Key biomechanical parameters of the repair, including the ultimate tensile strength (UTS), yield strength, 3 mm gap force and stiffness, were calculated. Repairs were divided into 3 categories, early (first 10 days), intermediate (ensuing 10 days), and late repairs (final 10 days), and potential changes in repair properties over the training period were evaluated using a general linear modeling approach. There was a significant change in the mechanical characteristics of the repairs over the training period, evidencing a clear learning effect (p < 0.05). Irrespective of the repair technique employed, early and intermediate repairs were characterized by a significantly lower UTS (29% and 20%, respectively), 3 mm gap (21% and 16%, respectively), and yield force (18% and 23%, respectively), but had a higher stiffness (33% and 38%, respectively) than late repairs (p < 0.05). The UTS of late repairs (47-48 N) were comparable to those published within the literature (45-51 N), suggesting surgical competence of the trainee. This simple, low-cost porcine model appears to be useful for providing preclinical training in flexor tendon repair techniques and has the potential to provide a quantitative index to evaluate the competency of surgical trainees. Further research is now required to identify optimal training parameters for flexor tendon repair and to develop procedure-specific standards for adequate benchmarking. Copyright © 2012 Association of Program Directors in Surgery. Published by Elsevier Inc. All rights reserved.

Effects of chlorhexidine-containing adhesives on the durability of resin-dentine interfaces.

PubMed

Stanislawczuk, Rodrigo; Pereira, Fabiane; Muñoz, Miguel Angel; Luque, Issis; Farago, Paulo Vitor; Reis, Alessandra; Loguercio, Alessandro D

2014-01-01

This study evaluated the effect of addition of diacetate CHX in different concentrations into two simplified etch-and-rinse (ER) adhesive systems (XP Bond [XP] and Ambar {AM}) on the ultimate tensile strength (UTS), degree of conversion (DC), 60-day cumulative water sorption (WS), solubility (SO) and CHX release (CR) as well as the immediate (IM) and 1-year (1Y) resin-dentine bond strength (μTBS) and nanoleakage (NL). Ten experimental adhesive systems were formulated according to the addition of CHX diacetate (0 [control], 0.01, 0.05, 0.1 and 0.2%) in the two ER. For UTS and DC, specimens were constructed and tested after 24h. For WS, SO and CR, after specimens build-up, they were stored in water and the properties measured after 60 days. The occlusal enamel of fifty molars was removed and the adhesives were applied in dentine surface after 37% phosphoric acid etching. After composite resin build-ups, specimens were longitudinally sectioned to obtain resin-dentine bonded sticks (0.8mm(2)). Specimens were tested in tension at 0.5mm/min in the IM or 1Y. For NL, 2 bonded sticks from each tooth were prepared and analyzed under SEM. The data were submitted to appropriate statistical analysis (α=0.05). The addition of CHX did not influence UTS, DC, WS and SO (p<0.05). Higher CR was observed in adhesives with higher concentration of CHX (p<0.05). After 1Y, significant reductions of μTBS and increases of NL were observed in the control groups (p<0.05). Reductions of μTBS and increase of NL over time were not observed (AM) for CHX-containing adhesives or it was less pronounced than the control (XP) regardless of the CHX concentration. The addition of CHX diacetate in concentrations until 0.2% in the simplified ER adhesive systems may be an alternative to increase the long-term stability of resin-dentine interfaces, without jeopardizing the adhesives' mechanical properties evaluated. Copyright © 2013. Published by Elsevier Ltd.

Assessment of the Effects of Plasma Bubbles on GAIM-GM

DTIC Science & Technology

2011-09-01

m / s , 230 m / s was chosen as a realistic upper bound that fit well into the modified IFM grid resolution. The sun...to a second condition where the bubbles would form at 2000 LT and then allowed to super-rotate at 230 m / s , or 7.5 degrees/hr, depicted in Figure 7...moving east at 230 m / s . Units are in TEC electrons per square meter. ( a ) 00UT (b) 01UT (c) 02UT (d) 03 UT (e) 04UT (f) 05UT 1 1 2 1

[Further microbiological studies of the air in a newly built (under the pavement) section of the underground railway in Budapest].

PubMed

Szám, L; Vedres, I; Csatai, L; Nikodemusz, I

1983-04-01

In three subway stations, which are "sub-pavement" stations (Budapest), microbiological air analyses were simultaneously carried out by means of sedimentation and by the use of Krotow's impactor. In the course of the examinations, which lasted eight months, the following max. values were obtained on the agar plates: 78 colonies/dm2/h and 239 colonies/m3; the rates of incidence for pathogenic and indicator bacteria were 2.7 and 1.7 per 10 plates. The strongest airflow was 0.7 m/sec. These values were obtained at the "Nagy-várad tér" station, which forms a transition to the subway stations. The "stopper effect" was found to exist here as well, although not to such an extent as in the deep subway stations, but still more pronounced than in the other two "subpavement" stations "Esceri ut" and "Határ ut". The microbiological values are at any rate more favourable than in the subway stations dealt with in an earlier paper.

Effects of short-term training on insulin sensitivity and skeletal muscle glucose metabolism in standardbred horses.

PubMed

Stewart-Hunt, L; Geor, R J; McCutcheon, L J

2006-08-01

Increased insulin sensitivity occurs after a period of exercise training, but the mechanisms underlying this training-associated increase in insulin action have not been investigated. To examine the effects of short-term endurance training (7 consecutive days) and a subsequent period of inactivity (5 days) on whole body insulin sensitivity and GLUT-4 protein and the activities of glycogen synthase (GS) and hexokinase (HK) in skeletal muscle. It was hypothesised that training would increase insulin sensitivity in association with increased GLUT-4 protein and activities of GS and HK, but that these changes would be transient, returning to baseline after 5 days of inactivity. Seven mature Standardbred horses completed training consisting of 7 consecutive days of 45 min of treadmill exercise at a speed that elicited 55% of pretraining maximal aerobic capacity (VO2peak). Insulin sensitivity was determined by rate of glucose disposal (M) during the last 60 min of a 120 min euglycaemic-hyperinsulinaemic clamp (EHC) performed before (-2 days) and at 1 and 6 days following training. VO2peak was measured before (UT) and after (TR) training and the period of inactivity (IA). Training resulted in a 9% increase in mean VO2peak (P<0.05) that was maintained following inactivity (IA). Mean M values were more than 2-fold higher (P<0.05) in TR than in UT. Mean M was also higher (P<0.05) in IA when compared to UT. GLUT-4 protien abundancewas more than 10-fold higher in TR and IA (P<0.001) than in UT. Pre-EHC GS activity and GS fractional velocity were increased (P<0.05) in TR when compared to UT and IA. Pre-EHC HK activity was increased (P<0.05) in IA when compared to UT and TR. Muscle glycogen was 66% lower (P<0.05) in TR than in UT and IA. Short-term training resulted in increases in whole body insulin sensitivity, and GLUT-4 protein content and glycogen synthase activity in skeletal muscle. The enhancements in insulin sensitivity, GLUT-4 protein and glycogen synthase activity were still evident after 5 days of inactivity. Insulin resistance in equids has been associated with obesity and predisposition to laminitis. Regular physical activity may mitigate risk of these conditions via enhancement of insulin sensitivity and/or control of bodyweight.

Generation and phenotypic analysis of mice lacking all urea transporters.

PubMed

Jiang, Tao; Li, Yingjie; Layton, Anita T; Wang, Weiling; Sun, Yi; Li, Min; Zhou, Hong; Yang, Baoxue

2017-02-01

Urea transporters (UT) are a family of transmembrane urea-selective channel proteins expressed in multiple tissues and play an important role in the urine concentrating mechanism of the mammalian kidney. UT inhibitors have diuretic activity and could be developed as novel diuretics. To determine if functional deficiency of all UTs in all tissues causes physiological abnormality, we established a novel mouse model in which all UTs were knocked out by deleting an 87 kb of DNA fragment containing most parts of Slc14a1 and Slc14a2 genes. Western blot analysis and immunofluorescence confirmed that there is no expression of urea transporter in these all-UT-knockout mice. Daily urine output was nearly 3.5-fold higher, with significantly lower urine osmolality in all-UT-knockout mice than that in wild-type mice. All-UT-knockout mice were not able to increase urinary urea concentration and osmolality after water deprivation, acute urea loading, or high protein intake. A computational model that simulated UT-knockout mouse models identified the individual contribution of each UT in urine concentrating mechanism. Knocking out all UTs also decreased the blood pressure and promoted the maturation of the male reproductive system. Thus, functional deficiency of all UTs caused a urea-selective urine-concentrating defect with little physiological abnormality in extrarenal organs. Copyright © 2016 International Society of Nephrology. Published by Elsevier Inc. All rights reserved.

Generation and phenotypic analysis of mice lacking all urea transporters

PubMed Central

Jiang, Tao; Li, Yingjie; Layton, Anita T.; Wang, Weiling; Sun, Yi; Li, Min; Zhou, Hong; Yang, Baoxue

2017-01-01

Urea transporters (UT) are a family of transmembrane urea-selective channel proteins expressed in multiple tissues and play an important role in the urine concentrating mechanism of the mammalian kidney. UT inhibitors have been identified to have diuretic activity and might be developed as novel diuretics. To determine if functional deficiency of all UTs in all tissues causes physiological abnormality, we established a novel mouse model in which all UTs were knocked out by deleting an 87 kb of DNA fragment containing most parts of Slc14a1 and Slc14a2 genes. Western blot analysis and immunofluorescence confirmed that there is no expression of urea transporter in all-UT-knockout mice. Daily urine output was nearly 3.5-fold higher, with significantly lower urine osmolality, in all-UT-knockout-mice than that in wild-type mice, and urine osmolality was significantly lower. All-UT-knockout mice were not able to increase urinary urea concentration and osmolality after water deprivation, acute urea loading or high protein intake. A computational model that simulated UT knockout mouse models identified the individual contribution of each UT in urine concentrating mechanism. Knocking out all UTs also decreased the blood pressure and promoted the maturation of the male reproductive system. These results revealed that functional deficiency of all UTs caused urea selective urine concentrating defect with little physiological abnormality in extrarenal organs. PMID:27914708

Orbit Estimation of Non-Cooperative Maneuvering Spacecraft

DTIC Science & Technology

2015-06-01

only take on values that generate real sigma points; therefore, λ > −n. The additional weighting scheme is outlined in the following equations κ = α2...orbit shapes resulted in a similar model weighting. Additional cases of this orbit type also resulted in heavily weighting smaller η value models. It is...determined using both the symmetric and additional parameters UTs. The best values for the weighting parameters are then compared for each test case

The effect of TiB2 reinforcement on the mechanical properties of an Al-Cu-Li alloy-based metal-matrix composite

NASA Technical Reports Server (NTRS)

1991-01-01

The addition of ceramic particles to aluminum based alloys can substantially improve mechanical properties, especially Young's modulus and room and elevated temperature strengths. However, these improvements typically occur at the expense of tensile ductility. The mechanical properties are evaluated to a metal matrix composite (MMC) consisting of an ultrahigh strength aluminum lithium alloy, Weldalite (tm) 049, reinforced with TiB2 particles produced by an in situ precipitation technique called the XD (tm) process. The results are compared to the behavior of a nonreinforced Weldalite 049 variant. It is shown that both 049 and 049-TiB2 show very attractive warm temperature properties e.g., 625 MPa yield strength at 150 C after 100 h at temperature. Weldalite 049 reinforced with a nominal 4 v pct. TiB2 shows an approx. 8 pct. increase in modulus and a good combination of strength (529 MPa UTS) and ductility (6.5 pct.) in the T3 temper. And the high ductility of Weldalite 049 in the naturally aged and underaged tempers makes the alloy a good, high strength matrix for ceramic reinforcement.

Development of Fine-Grained, Low-Carbon Bainitic Steels with High Strength and Toughness Produced Through the Conventional Hot-Rolling and Air-Cooling

NASA Astrophysics Data System (ADS)

Dhua, Sanjay Kumar; Sarkar, Partha Pratim; Saxena, Atul; Jha, Bimal Kumar

2016-12-01

Low-carbon bainitic steels have created enormous interest among scientists across the world in the past few decades because of their high strength, toughness, and weldability replacing the conventional quenched and tempered medium-carbon steels. Three experimental steels with varying alloy additions were made in a 100-kg laboratory induction furnace and cast into 100-mm-diameter cylindrical ingots. These ingots were hot-rolled and air-cooled to 6-mm plates in an experimental rolling mill with selected thermomechanical parameters. Steels processed through this process provided an ultrafine low-carbon bainitic microstructure with maximum yield strength (YS) and ultimate tensile strength (UTS) 575 and 705 MPa, respectively. The Charpy impact toughness of the experimental steels was excellent, and at 253 K (-20 °C), it varied from 114 to 170 Joules. Cu-B-added steel was found to give an optimum combination of strength, YS-575 MPa, and toughness, 114 J at 253 K (-20 °C). Thus, fine-grained, low-carbon bainitic steels could be developed with a proper combination of alloying elements and thermomechanical parameters even by air-cooling.

Magnetic excitation spectra of strongly correlated quasi-one-dimensional systems: Heisenberg versus Hubbard-like behavior

DOE PAGES

Nocera, Alberto; Patel, Niravkumar D.; Fernandez-Baca, Jaime A.; ...

2016-11-28

In this paper, we study the effects of charge degrees of freedom on the spin excitation dynamics in quasi-one-dimensional magnetic materials. Using the density matrix renormalization group method, we calculate the dynamical spin structure factor of the Hubbard model at half electronic filling on a chain and on a ladder geometry, and compare the results with those obtained using the Heisenberg model, where charge degrees of freedom are considered frozen. For both chains and two-leg ladders, we find that the Hubbard model spectrum qualitatively resembles the Heisenberg spectrum—with low-energy peaks resembling spinonic excitations—already at intermediate on-site repulsion as small asmore » U/t ~ 2–3, although ratios of peak intensities at different momenta continue evolving with increasing U/t converging only slowly to the Heisenberg limit. Finally, we discuss the implications of these results for neutron scattering experiments and we propose criteria to establish the values of U/t of quasi-one-dimensional systems described by one-orbital Hubbard models from experimental information.« less

Magnetic excitation spectra of strongly correlated quasi-one-dimensional systems: Heisenberg versus Hubbard-like behavior

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nocera, Alberto; Patel, Niravkumar D.; Fernandez-Baca, Jaime A.

In this paper, we study the effects of charge degrees of freedom on the spin excitation dynamics in quasi-one-dimensional magnetic materials. Using the density matrix renormalization group method, we calculate the dynamical spin structure factor of the Hubbard model at half electronic filling on a chain and on a ladder geometry, and compare the results with those obtained using the Heisenberg model, where charge degrees of freedom are considered frozen. For both chains and two-leg ladders, we find that the Hubbard model spectrum qualitatively resembles the Heisenberg spectrum—with low-energy peaks resembling spinonic excitations—already at intermediate on-site repulsion as small asmore » U/t ~ 2–3, although ratios of peak intensities at different momenta continue evolving with increasing U/t converging only slowly to the Heisenberg limit. Finally, we discuss the implications of these results for neutron scattering experiments and we propose criteria to establish the values of U/t of quasi-one-dimensional systems described by one-orbital Hubbard models from experimental information.« less

Localization and regulation of a facilitative urea transporter in the kidney of the red-eared slider turtle (Trachemys scripta elegans).

PubMed

Uchiyama, Minoru; Kikuchi, Ryosuke; Konno, Norifumi; Wakasugi, Tatsuya; Matsuda, Kouhei

2009-01-01

Urea is the major excretory end product of nitrogen metabolism in most chelonian reptiles. In the present study, we report the isolation of a 1632 base pair cDNA from turtle kidney with one open reading frame putatively encoding a 403-residue protein, the turtle urea transporter (turtle UT). The first cloned reptilian UT has high homology with UTs (facilitated urea transporters) cloned from vertebrates, and most closely resembles the UT-A subfamily. Injection of turtle UT cRNA into Xenopus oocytes induced a 6-fold increase in [(14)C]urea uptake that was inhibited by phloretin. The turtle UT mRNA expression and tissue distribution were examined by RT-PCR with total RNA from various tissues. Expression of turtle UT mRNA was restricted to the kidney, and no signal was detected in the other tissues, such as brain, heart, alimentary tract and urinary bladder. An approximately 58 kDa protein band was detected in membrane fractions of the kidney by western blot using an affinity-purified antibody that recognized turtle UT expressed in Xenopus oocytes. In an immunohistochemical study using the anti-turtle UT antibody, UT-immunopositive cells were observed along the distal tubule but not in the collecting duct. In turtles under dry conditions, plasma osmolality and urea concentration increased, and using semi-quantitative RT-PCR the UT mRNA expression level in the kidney was found to increase 2-fold compared with control. The present results, taken together, suggest that the turtle UT probably contributes to urea transport in the distal tubule segments of the kidney in response to hyperosmotic stress under dry conditions.

EARTH’S ROTATIONAL DECELERATION: DETERMINATION OF TIDAL FRICTION INDEPENDENT OF TIMESCALES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deines, Steven D.; Williams, Carol A., E-mail: steven.deines@gmail.com, E-mail: cw@math.usf.edu

This paper determines Earth's rotational deceleration without relying on atomic or ephemeris timescales. Earth's rotation defines the civil time standard called Universal Time (UT). Our previous paper did not examine tidal friction in depth when analyzing the timescale divergence between UT and International Atomic Time (TAI). We examine all available paleontological fossils and deposits for the direct measurements of Earth's past rotation rates, because that record includes all contributing effects. We examine paleontological reports that date Earth's rotation rate using corals, bivalves, brachiopods, rhythmites, and stromatolites. Contributions that vary Earth's moment of inertia, such as continental plate drifts, coastline changes, icemore » age formations, and viscous glacial rebounds, are superimposed with the secular deceleration. The average deceleration of Earth's rotation rate from all available fossil data is found to be (5.969 ± 1.762) × 10{sup −7} rad yr{sup −2}. Our value is 99.8% of the total rotational deceleration determined by Christodoulidis et al., who used artificial satellite data, and our value is 96.6% of the expected tidal friction value obtained by Stephenson and Morrison. Taking the derivative of conserved angular momentum, the predicted lunar orbital deceleration caused by the average rotational deceleration corresponds closely to lunar models. When evaluating the significant time gaps between UT and TAI, Earth's rotational deceleration is a minor contributing factor. Also, the secular deceleration rate is necessary to correctly date ancient astronomical events. We strongly encourage that more ocean paleontological evidence be found to supplement the record to separate the many periodic variations embedded in these data.« less

Renal Phenotype of UT-A Urea Transporter Knockout Mice

PubMed Central

Fenton, Robert A.; Flynn, Anneliese; Shodeinde, Adetola; Smith, Craig P.; Schnermann, Jurgen; Knepper, Mark A.

2006-01-01

The urea transporters UT-A1 and UT-A3 mediate rapid transepithelial urea transport across the inner medullary collecting duct (IMCD). In a previous study, using a new mouse model in which both UT-A1 and UT-A3 were genetically deleted from the IMCD (UT-A1/3−/− mice), we investigated the role of these transporters in the function of the renal inner medulla. Here we report a series of studies investigating more generally the renal phenotype of UT-A1/3−/− mice. Pathological screening revealed abnormalities in both the testis (increased size) and kidney (decreased size and vascular congestion) of UT-A1/3−/− mice. Total urinary nitrate and nitrite excretion rates in UT-A1/3−/− mice were more than double those in wildtype mice. Total renal blood flow was not different between UT-A1/3−/− and wildtype mice, but underwent a greater percentage decrease in response to NG-Nitro-L-arginine Methyl Ester Hydrochloride (L-NAME) infusion. Whole kidney glomerular filtration rate was not different in UT-A1/3−/− mice compared to controls and underwent a similar increase in response to a greater dietary protein intake. Fractional urea excretion was markedly elevated in UT-A1/3−/− mice on a 40% protein diet, reaching 102.4 ± 8.8% of the filtered load, suggesting that there may be active urea secretion along the renal tubule. Although there was a marked urinary concentrating defect in UT-A1/3−/− mice, there was no decrease in aquaporin-2 or -3 expression. Furthermore, although urea accumulation in the inner medulla was markedly attenuated, there was no decrease in NaCl concentration in tissue from outer medulla or 2 levels of the inner medulla. PMID:15829709

Ca Addition Effects on the Microstructure, Tensile and Corrosion Properties of Mg Matrix Alloy Containing 8 wt.% Mg2Si

NASA Astrophysics Data System (ADS)

Lotfpour, M.; Emamy, M.; Dehghanian, C.; Pourbahari, B.

2018-02-01

The microstructure, tensile properties and corrosion behavior of the Mg-8 wt.% Mg2Si-x%Ca alloy have been studied by the use of optical microscopy, scanning electron microscopy equipped with energy-dispersive spectroscopy, x-ray diffraction, standard tensile testing, polarization test and electrochemical impedance spectroscopy (EIS) measurements. Microstructural studies indicated that Ca modifies both primary and eutectic Mg2Si phase. It was found that the average size of primary Mg2Si particles is about 60 μm, which is dropped by about 82% in the alloy containing 0.05 wt.% Ca. By the addition of different Ca contents, Ca-rich intermetallics (i.e., CaSi2 and CaMgSi) were formed. The modification mechanism of adding Ca during solidification was found to be due to the strong effect of CaMgSi phase as a heterogonous nucleation site, apart from CaSi2 which was reported before, for Mg2Si intermetallics. Tensile testing results ascertained that Ca addition enhances both ultimate tensile strength (UTS) and elongation values. The optimum amount of Ca was found to be 0.1 wt.%, which improved UTS and elongation values from about 130 MPa and 2% to 165 MPa and 5.5%, whereas more Ca addition (i.e., 3 wt.%) reduced the tensile properties of the alloy to about 105 MPa and 1.8%, which can be due to the formation of CaMgSi intermetallics with deteriorating needle-like morphology. Polarization and EIS tests also showed that the Mg-3%Si-0.5%Ca alloy pronounces as the best anti-corrosion alloy. Nevertheless, further added Ca (up to 3 wt.%) deteriorated the corrosion resistance due to predominance of worse galvanic coupling effect stemmed from the presence of stronger CaMgSi cathode in comparison with Mg2Si. With higher Ca additions, an adverse effect was seen on corrosion resistance of the Mg-3%Si alloy, as a result of forming a weak film on the alloy specimen surface.

Influence of irradiation by a novel CO2 9.3-μm short-pulsed laser on sealant bond strength.

PubMed

Rechmann, P; Sherathiya, K; Kinsel, R; Vaderhobli, R; Rechmann, B M T

2017-04-01

The objective of this in vitro study was to evaluate whether irradiation of enamel with a novel CO 2 9.3-μm short-pulsed laser using energies that enhance caries resistance influences the shear bond strength of composite resin sealants to the irradiated enamel. Seventy bovine and 240 human enamel samples were irradiated with a 9.3-μm carbon dioxide laser (Solea, Convergent Dental, Inc., Natick, MA) with four different laser energies known to enhance caries resistance or ablate enamel (pulse duration from 3 μs at 1.6 mJ/pulse to 43 μs at 14.9 mJ/pulse with fluences between 3.3 and 30.4 J/cm 2 , pulse repetition rate between 4.1 and 41.3 Hz, beam diameter of 0.25 mm and 1-mm spiral pattern, and focus distance of 4-15 mm). Irradiation was performed "freehand" or using a computerized, motor-driven stage. Enamel etching was achieved with 37% phosphoric acid (Scotchbond Universal etchant, 3M ESPE, St. Paul, MN). As bonding agent, Adper Single Bond Plus was used followed by placing Z250 Filtek Supreme flowable composite resin (both 3M ESPE). After 24 h water storage, a single-plane shear bond test was performed (UltraTester, Ultradent Products, Inc., South Jordan, UT). All laser-irradiated samples showed equal or higher bond strength than non-laser-treated controls. The highest shear bond strength values were observed with the 3-μs pulse duration/0.25-mm laser pattern (mean ± SD = 31.90 ± 2.50 MPa), representing a significant 27.4% bond strength increase over the controls (25.04 ± 2.80 MPa, P ≤ 0.0001). Two other caries-preventive irradiation (3 μs/1 mm and 7 μs/0.25 mm) and one ablative pattern (23 μs/0.25 mm) achieved significantly increased bond strength compared to the controls. Bovine enamel also showed in all test groups increased shear bond strength over the controls. Computerized motor-driven stage irradiation did not show superior bond strength values over the clinically more relevant freehand irradiation. Enamel that is made caries-resistant with CO 2 9.3-μm short-pulsed laser irradiation showed at least equal or significantly higher shear bond strength to pit and fissure sealants than non-laser-irradiated enamel. The risk of a sealant failure due to CO 2 9.3-μm short-pulsed laser irradiation appears reduced. If additional laser ablation is required before placing a sealant, the CO 2 9.3-μm enamel laser-cut showed equivalent or superior bond strength to a flowable sealant.

Rehabilitation Exercises to Induce Balanced Scapular Muscle Activity in an Anti-gravity Posture

PubMed Central

Ishigaki, Tomonobu; Yamanaka, Masanori; Hirokawa, Motoki; Tai, Keita; Ezawa, Yuya; Samukawa, Mina; Tohyama, Harukazu; Sugawara, Makoto

2014-01-01

[Purpose] The purpose of this study was to compare the intramuscular balance ratios of the upper trapezius muscle (UT) and the lower trapezius muscle (LT), and the intermuscular balance ratios of the UT and the serratus anterior muscle (SA) among prone extension (ProExt), prone horizontal abduction with external rotation (ProHAbd), forward flexion in the side-lying position (SideFlex), side-lying external rotation (SideEr), shoulder flexion with glenohumeral horizontal abduction load (FlexBand), and shoulder flexion with glenohumeral horizontal adduction load (FlexBall) in the standing posture. [Methods] The electromyographic (EMG) activities of the UT, LT and SA were measured during the tasks. The percentage of maximum voluntary isometric contraction (%MVIC) was calculated for each muscle, and the UT/LT ratios and the UT/SA ratios were compared among the tasks. [Results] The UT/LT ratio with the FlexBand was not significantly different from those of the four exercises in the side-lying and prone postures. The UT/SA ratio with the FlexBall demonstrated appropriate balanced activity. [Conclusion] In an anti-gravity posture, we recommend the FlexBand and the FlexBall for inducing balanced UT/LT and UT/SA ratios, respectively. PMID:25540485

The UT-A Urea Transporter Promoter, UT-Aα, Targets Principal Cells of the Renal Inner Medullary Collecting Duct

PubMed Central

Fenton, Robert A.; Shodeinde, Adetola; Knepper, Mark A.

2006-01-01

The urea transporters, UT-A1 and UT-A3, two members of the UT-A gene family, are localized to the terminal portion of the inner medullary collecting duct (IMCD). In this manuscript, we demonstrate that 4.2-kb of the 5′-flanking region of the UT-A gene (UT-Aα promoter) is sufficient to drive the IMCD-specific expression of a heterologous reporter gene, β-galactosidase (β-Gal), in transgenic mice. RT-PCR, immunoblotting and immunohistochemistry demonstrate that within the kidney, transgene expression is confined to the terminal portion of the IMCD. Co-localization studies with aquaporin 2 show that expression is localized to the principal cells of the IMCD2 and IMCD3 regions. Utilizing β-Gal activity assays, we further show that within the kidney, the β-Gal transgene can be regulated by both water restriction and glucocorticoids, similar to the regulation of the endogenous UT-A gene. These results demonstrate that 4.2-kb of the UT-Aα promoter is sufficient to drive expression of a heterologous reporter gene in a tissue-specific and cell-specific fashion in transgenic mice PMID:16091580

Rehabilitation Exercises to Induce Balanced Scapular Muscle Activity in an Anti-gravity Posture.

PubMed

Ishigaki, Tomonobu; Yamanaka, Masanori; Hirokawa, Motoki; Tai, Keita; Ezawa, Yuya; Samukawa, Mina; Tohyama, Harukazu; Sugawara, Makoto

2014-12-01

[Purpose] The purpose of this study was to compare the intramuscular balance ratios of the upper trapezius muscle (UT) and the lower trapezius muscle (LT), and the intermuscular balance ratios of the UT and the serratus anterior muscle (SA) among prone extension (ProExt), prone horizontal abduction with external rotation (ProHAbd), forward flexion in the side-lying position (SideFlex), side-lying external rotation (SideEr), shoulder flexion with glenohumeral horizontal abduction load (FlexBand), and shoulder flexion with glenohumeral horizontal adduction load (FlexBall) in the standing posture. [Methods] The electromyographic (EMG) activities of the UT, LT and SA were measured during the tasks. The percentage of maximum voluntary isometric contraction (%MVIC) was calculated for each muscle, and the UT/LT ratios and the UT/SA ratios were compared among the tasks. [Results] The UT/LT ratio with the FlexBand was not significantly different from those of the four exercises in the side-lying and prone postures. The UT/SA ratio with the FlexBall demonstrated appropriate balanced activity. [Conclusion] In an anti-gravity posture, we recommend the FlexBand and the FlexBall for inducing balanced UT/LT and UT/SA ratios, respectively.

A Comprehensive Study on the Internet of Underwater Things: Applications, Challenges, and Channel Models †

PubMed Central

Wu, Geng-De; Huang, Chun-Ju

2017-01-01

The Internet of Underwater Things (IoUT) is a novel class of Internet of Things (IoT), and is defined as the network of smart interconnected underwater objects. IoUT is expected to enable various practical applications, such as environmental monitoring, underwater exploration, and disaster prevention. With these applications, IoUT is regarded as one of the potential technologies toward developing smart cities. To support the concept of IoUT, Underwater Wireless Sensor Networks (UWSNs) have emerged as a promising network system. UWSNs are different from the traditional Territorial Wireless Sensor Networks (TWSNs), and have several unique properties, such as long propagation delay, narrow bandwidth, and low reliability. These unique properties would be great challenges for IoUT. In this paper, we provide a comprehensive study of IoUT, and the main contributions of this paper are threefold: (1) we introduce and classify the practical underwater applications that can highlight the importance of IoUT; (2) we point out the differences between UWSNs and traditional TWSNs, and these differences are the main challenges for IoUT; and (3) we investigate and evaluate the channel models, which are the technical core for designing reliable communication protocols on IoUT. PMID:28640220

A Comprehensive Study on the Internet of Underwater Things: Applications, Challenges, and Channel Models.

PubMed

Kao, Chien-Chi; Lin, Yi-Shan; Wu, Geng-De; Huang, Chun-Ju

2017-06-22

The Internet of Underwater Things (IoUT) is a novel class of Internet of Things (IoT), and is defined as the network of smart interconnected underwater objects. IoUT is expected to enable various practical applications, such as environmental monitoring, underwater exploration, and disaster prevention. With these applications, IoUT is regarded as one of the potential technologies toward developing smart cities. To support the concept of IoUT, Underwater Wireless Sensor Networks (UWSNs) have emerged as a promising network system. UWSNs are different from the traditional Territorial Wireless Sensor Networks (TWSNs), and have several unique properties, such as long propagation delay, narrow bandwidth, and low reliability. These unique properties would be great challenges for IoUT. In this paper, we provide a comprehensive study of IoUT, and the main contributions of this paper are threefold: (1) we introduce and classify the practical underwater applications that can highlight the importance of IoUT; (2) we point out the differences between UWSNs and traditional TWSNs, and these differences are the main challenges for IoUT; and (3) we investigate and evaluate the channel models, which are the technical core for designing reliable communication protocols on IoUT.

Middle and long-term prediction of UT1-UTC based on combination of Gray Model and Autoregressive Integrated Moving Average

NASA Astrophysics Data System (ADS)

Jia, Song; Xu, Tian-he; Sun, Zhang-zhen; Li, Jia-jing

2017-02-01

UT1-UTC is an important part of the Earth Orientation Parameters (EOP). The high-precision predictions of UT1-UTC play a key role in practical applications of deep space exploration, spacecraft tracking and satellite navigation and positioning. In this paper, a new prediction method with combination of Gray Model (GM(1, 1)) and Autoregressive Integrated Moving Average (ARIMA) is developed. The main idea is as following. Firstly, the UT1-UTC data are preprocessed by removing the leap second and Earth's zonal harmonic tidal to get UT1R-TAI data. Periodic terms are estimated and removed by the least square to get UT2R-TAI. Then the linear terms of UT2R-TAI data are modeled by the GM(1, 1), and the residual terms are modeled by the ARIMA. Finally, the UT2R-TAI prediction can be performed based on the combined model of GM(1, 1) and ARIMA, and the UT1-UTC predictions are obtained by adding the corresponding periodic terms, leap second correction and the Earth's zonal harmonic tidal correction. The results show that the proposed model can be used to predict UT1-UTC effectively with higher middle and long-term (from 32 to 360 days) accuracy than those of LS + AR, LS + MAR and WLS + MAR.

Biochemical properties of urea transporters.

PubMed

Chen, Guangping

2014-01-01

Urea and urea transporters (UT) are critical to the production of concentrated urine and hence in maintaining body fluid balance. The UT-A1 urea transporter is the major and most important UT isoform in the kidney. Native UT-A1, expressed in the terminal inner medullary collecting duct (IMCD) epithelial cells, is a glycosylated protein with two glycoforms of 117 and 97 kDa. Vasopressin is the major hormone in vivo that rapidly increases urea permeability in the IMCD through increases in phosphorylation and apical plasma-membrane accumulation of UT-A1. The cell signaling pathway for vasopressin-mediated UT-A1 phosphorylation and activity involves two cAMP-dependent signaling pathways: protein kinase A (PKA) and exchange protein activated by cAMP (Epac). In this chapter, we will discuss UT-A1 regulation by phosphorylation, ubiquitination, and glycosylation.

Climatology and long-term evolution of ozone and carbon monoxide in the upper troposphere-lower stratosphere (UTLS) at northern midlatitudes, as seen by IAGOS from 1995 to 2013

NASA Astrophysics Data System (ADS)

Cohen, Yann; Petetin, Hervé; Thouret, Valérie; Marécal, Virginie; Josse, Béatrice; Clark, Hannah; Sauvage, Bastien; Fontaine, Alain; Athier, Gilles; Blot, Romain; Boulanger, Damien; Cousin, Jean-Marc; Nédélec, Philippe

2018-04-01

In situ measurements in the upper troposphere-lower stratosphere (UTLS) have been performed in the framework of the European research infrastructure IAGOS (In-service Aircraft for a Global Observing System) for ozone since 1994 and for carbon monoxide (CO) since 2002. The flight tracks cover a wide range of longitudes in the northern extratropics, extending from the North American western coast (125° W) to the eastern Asian coast (135° E) and more recently over the northern Pacific Ocean. Several tropical regions are also sampled frequently, such as the Brazilian coast, central and southern Africa, southeastern Asia, and the western half of the Maritime Continent. As a result, a new set of climatologies for O3 (August 1994-December 2013) and CO (December 2001-December 2013) in the upper troposphere (UT), tropopause layer, and lower stratosphere (LS) are made available, including gridded horizontal distributions on a semi-global scale and seasonal cycles over eight well-sampled regions of interest in the northern extratropics. The seasonal cycles generally show a summertime maximum in O3 and a springtime maximum in CO in the UT, in contrast to the systematic springtime maximum in O3 and the quasi-absence of a seasonal cycle of CO in the LS. This study highlights some regional variabilities in the UT, notably (i) a west-east difference of O3 in boreal summer with up to 15 ppb more O3 over central Russia compared with northeast America, (ii) a systematic west-east gradient of CO from 60 to 140° E, especially noticeable in spring and summer with about 5 ppb by 10 degrees longitude, (iii) a broad spring/summer maximum of CO over northeast Asia, and (iv) a spring maximum of O3 over western North America. Thanks to almost 20 years of O3 and 12 years of CO measurements, the IAGOS database is a unique data set to derive trends in the UTLS at northern midlatitudes. Trends in O3 in the UT are positive and statistically significant in most regions, ranging from +0.25 to +0.45 ppb yr-1, characterized by the significant increase in the lowest values of the distribution. No significant trends of O3 are detected in the LS. Trends of CO in the UT, tropopause, and LS are almost all negative and statistically significant. The estimated slopes range from -1.37 to -0.59 ppb yr-1, with a nearly homogeneous decrease in the lowest values of the monthly distribution (5th percentile) contrasting with the high interregional variability in the decrease in the highest values (95th percentile).

Modeling of flux, binding and substitution of urea molecules in the urea transporter dvUT.

PubMed

Zhang, Hai-Tian; Wang, Zhe; Yu, Tao; Sang, Jian-Ping; Zou, Xian-Wu; Zou, Xiaoqin

2017-09-01

Urea transporters (UTs) are transmembrane proteins that transport urea molecules across cell membranes and play a crucial role in urea excretion and water balance. Modeling the functional characteristics of UTs helps us understand how their structures accomplish the functions at the atomic level, and facilitates future therapeutic design targeting the UTs. This study was based on the crystal structure of Desulfovibrio vulgaris urea transporter (dvUT). To model the binding behavior of urea molecules in dvUT, we constructed a cooperative binding model. To model the substitution of urea by the urea analogue N,N'-dimethylurea (DMU) in dvUT, we calculated the occupation probability of DMU along the urea pore and the ratio of the occupation probabilities of DMU at the external (S ext ) and internal (S int ) binding sites, and we established the mutual substitution rule for binding and substitution of urea and DMU. Based on these calculations and modelings, together with the use of the Monte Carlo (MC) method, we further modeled the urea flux in dvUT, equilibrium urea binding to dvUT, and the substitution of urea by DMU in the dvUT. Our modeling results are in good agreement with the existing experimental functional data. Furthermore, the modelings have discovered the microscopic process and mechanisms of those functional characteristics. The methods and the results would help our future understanding of the underlying mechanisms of the diseases associated with impaired UT functions and rational drug design for the treatment of these diseases. Copyright © 2017 Elsevier Inc. All rights reserved.

Rupture utérine sur utérus bicorne à 12 semaines d'aménorrhée: à propos d'un cas

PubMed Central

Itchimouh, Sanaa; Khabtou, Karima; Mahdaoui, Sakher; Boufettal, Houssine; Samouh, Naima

2016-01-01

La fréquence des malformations utérines ayant un impact sur la reproduction est difficile à apprécier. Leur mise en évidence nécessite un bilan spécifique (hystérosalpingographie, hystéroscopie, cœlioscopie). La fertilité spontanée peut être altérée en fonction du type d'anomalie utérine. Toutes ces anomalies peuvent avoir des répercussions sur l’évolution de la conception à type de fausses couches précoces et tardives, de grossesse extra utérine, de menace d'accouchement prématuré, d'accouchement prématuré, de pathologies vasculaires gravidiques et de retard de croissance intra-utérin. L'utérus bicorne est la plus connue des malformations et représente environ la moitié des anomalies de l'utérus. La survenue d'une telle grossesse constitue une situation à risque pouvant entraîner une mort maternelle, mais le diagnostic précoce et un bon suivi peut mener des grossesses à terme sur des utérus malformé. Le dépistage échographique devrait permettre la détection systématique de ce genre de cas afin de prendre préventivement les mesures qui s'imposent. Nous rapportons un cas de rupture utérine sur utérus bicorne unicervical sur grossesse à 12 semaines d'aménorrhée. PMID:27642490

Multiscale structure and damage tolerance of coconut shells.

PubMed

Gludovatz, B; Walsh, F; Zimmermann, E A; Naleway, S E; Ritchie, R O; Kruzic, J J

2017-12-01

We investigated the endocarp of the fruit of Cocos nucifera (i.e., the inner coconut shell), examining the structure across multiple length scales through advanced characterization techniques and in situ testing of mechanical properties. Like many biological materials, the coconut shell possesses a hierarchical structure with distinct features at different length scales that depend on orientation and age. Aged coconut was found to have a significantly stronger (ultimate tensile strength, UTS = 48.5MPa), stiffer (Young's modulus, E = 1.92GPa), and tougher (fracture resistance (R-curve) peak of K J = 3.2MPa m 1/2 ) endocarp than the younger fruit for loading in the latitudinal orientation. While the mechanical properties of coconut shell were observed to improve with age, they also become more anisotropic: the young coconut shell had the same strength (17MPa) and modulus (0.64GPa) values and similar R-curves for both longitudinal and latitudinal loading configurations, whereas the old coconut had 82% higher strength for loading in the latitudinal orientation, and >50% higher crack growth toughness for cracking on the latitudinal plane. Structural aspects affecting the mechanical properties across multiple length scales with aging were identified as improved load transfer to the cellulose crystalline nanostructure (identified by synchrotron x-ray diffraction) and sclerification of the endocarp, the latter of which included closing of the cell lumens and lignification of the cell walls. The structural changes gave a denser and mechanically superior micro and nanostructure to the old coconut shell. Additionally, the development of anisotropy was attributed to the formation of an anisotropic open channel structure throughout the shell of the old coconut that affected both crack initiation during uniaxial tensile tests and the toughening mechanisms of crack trapping and deflection during crack propagation. Copyright © 2017 Elsevier Ltd. All rights reserved.

78 FR 45473 - Proposed Amendment of Class E Airspace; St. George, UT

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-29

...-0600; Airspace Docket No. 13-ANM-18 Proposed Amendment of Class E Airspace; St. George, UT AGENCY... action proposes to amend Class E airspace at St. George Municipal Airport, St. George, UT, by removing... aircraft operations at St. George Municipal Airport, St. George, UT. DATES: Comments must be received on or...

76 FR 2800 - Establishment of Class E Airspace; Lucin, UT

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-18

...-2010-1208; Airspace Docket No. 10-ANM-16] Establishment of Class E Airspace; Lucin, UT AGENCY: Federal... E en route domestic airspace for the Lucin VORTAC, Lucin, UT. DATES: Effective 0901 UTC, February 17..., UT, incorrectly referenced the existing Class E en route domestic airspace exclusion above 8,500 feet...

Deletion of the UT receptor gene results in the selective loss of urotensin-II contractile activity in aortae isolated from UT receptor knockout mice

PubMed Central

Behm, David J; Harrison, Stephen M; Ao, Zhaohui; Maniscalco, Kristeen; Pickering, Susan J; Grau, Evelyn V; Woods, Tina N; Coatney, Robert W; Doe, Christopher P A; Willette, Robert N; Johns, Douglas G; Douglas, Stephen A

2003-01-01

Urotensin-II (U-II) is among the most potent mammalian vasoconstrictors identified and may play a role in the aetiology of essential hypertension. Currently, only one mouse U-II receptor (UT) gene has been cloned. It is postulated that this protein is solely responsible for mediating U-II-induced vasoconstriction. This hypothesis has been investigated in the present study, which assessed basal haemodynamics and vascular reactivity to hU-II in wild-type (UT(+/+)) and UT receptor knockout (UT(−/−)) mice. Basal left ventricular end-diastolic and end-systolic volumes/pressures, stroke volumes, mean arterial blood pressures, heart rates, cardiac outputs and ejection fractions in UT(+/+) mice and in UT(−/−) mice were similar. Relative to UT(+/+) mouse isolated thoracic aorta, where hU-II was a potent spasmogen (pEC50=8.26±0.08) that evoked relatively little vasoconstriction (17±2% 60 mM KCl), vessels isolated from UT(−/−) mice did not respond to hU-II. However, in contrast, the superior mesenteric artery isolated from both the genotypes did not contract in the presence of hU-II. Reactivity to unrelated vasoconstrictors (phenylephrine, endothelin-1, KCl) and endothelium-dependent/independent vasodilator agents (carbachol, sodium nitroprusside) was similar in the aorta and superior mesenteric arteries isolated from both the genotypes. The present study is the first to directly link hU-II-induced vasoconstriction with the UT receptor. Deletion of the UT receptor gene results in loss of hU-II contractile action with no ‘nonspecific' alterations in vascular reactivity. However, as might be predicted based on the limited contractile efficacy recorded in vitro, the contribution that hU-II and its receptor make to basal systemic haemodynamics appears to be negligible in this species. PMID:12770952

The Effects of Pulsed Radiation Therapy on Tumor Oxygenation in 2 Murine Models of Head and Neck Squamous Cell Carcinoma

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wobb, Jessica; Krueger, Sarah A.; Kane, Jonathan L.

2015-07-15

Purpose: To evaluate the efficacy of low-dose pulsed radiation therapy (PRT) in 2 head and neck squamous cell carcinoma (HNSCC) xenografts and to investigate the mechanism of action of PRT compared with standard radiation therapy (SRT). Methods and Materials: Subcutaneous radiosensitive UT-SCC-14 and radioresistant UT-SCC-15 xenografts were established in athymic NIH III HO female mice. Tumors were irradiated with 2 Gy/day by continuous standard delivery (SRT: 2 Gy) or discontinuous low-dose pulsed delivery (PRT: 0.2 Gy × 10 with 3-min pulse interval) to total doses of 20 Gy (UT14) or 40 Gy (UT15) using a clinical 5-day on/2-day off schedule. Treatment response was assessed by changes inmore » tumor volume, {sup 18}F-fluorodeoxyglucose (FDG) (tumor metabolism), and {sup 18}F-fluoromisonidazole (FMISO) (hypoxia) positron emission tomography (PET) imaging before, at midpoint, and after treatment. Tumor hypoxia using pimonidazole staining and vascular density (CD34 staining) were assessed by quantitative histopathology. Results: UT15 and UT14 tumors responded similarly in terms of growth delay to either SRT or PRT. When compared with UT14 tumors, UT15 tumors demonstrated significantly lower uptake of FDG at all time points after irradiation. UT14 tumors demonstrated higher levels of tumor hypoxia after SRT when compared with PRT as measured by {sup 18}F-FMISO PET. By contrast, no differences were seen in {sup 18}F-FMISO PET imaging between SRT and PRT for UT15 tumors. Histologic analysis of pimonidazole staining mimicked the {sup 18}F-FMISO PET imaging data, showing an increase in hypoxia in SRT-treated UT14 tumors but not PRT-treated tumors. Conclusions: Differences in {sup 18}F-FMISO uptake for UT14 tumors after radiation therapy between PRT and SRT were measurable despite the similar tumor growth delay responses. In UT15 tumors, both SRT and PRT were equally effective at reducing tumor hypoxia to a significant level as measured by {sup 18}F-FMISO and pimonidazole.« less

Effects of quaternary ammonium-methacrylates on the mechanical properties of unfilled resins.

PubMed

Hoshika, Tomohiro; Nishitani, Yoshihiro; Yoshiyama, Masahiro; Key, William O; Brantley, William; Agee, Kelli A; Breschi, Lorenzo; Cadenaro, Milena; Tay, Franklin R; Rueggeberg, Frederick; Pashley, David H

2014-11-01

Adding antimicrobial/anti-MMP quaternary ammonium methacrylates (QAMs) to comonomer blends should not weaken the mechanical properties of dental resins. This work evaluated the degree conversion and mechanical properties of BisGMA/TEGDMA/HEMA (60:30:10) containing 0-15 mass% QAMs A-E (A: 2-acryloxyethyltrimethyl ammonium chloride; B: [3-(methacryloylamino)propyl]trimethylammonium chloride; C: [2-(methacryloxy)ethyl] trimethyl ammonium chloride; D: diallyldimethyl ammonium chloride; E: 2-(methacryloyloxy) ethyltrimethyl ammonium methyl sulfate. Unfilled resins with and without QAM were placed on ATR-FTIR and light-polymerized for 20s in a thin film at 30°C. Unfilled resin beams were casted from square hollow glass tubings. Half of the beams were tested after 3 days of drying (control); the other half were tested wet after 3 days of water storage. Addition of QAMs in control resins significantly increased conversion 600 s after light termination, with the exception of 5% MAPTAC (p<0.05). Increase of QAM content within a formulation significantly increased conversion. Control beams gave dry Young's moduli of ∼700 MPa. Addition of 5, 10 or 15 mass% QAMs produced significant reductions in dry Young's moduli except for 5% B or C. 15 mass% A, B and C lowered the wet Young's moduli of the resin beams by more than 30%. The ultimate tensile stress (UTS) of control dry resin was 89±11 MPa. Addition of 5-10 mass% QAMs had no adverse effect on the dry UTS. After water storage, the UTS of all resin blends fell significantly (p<0.05), especially when 15 wt% QAMs was added. Control dry beams gave fracture toughness (KIC) values of 0.88±0.1 MPa m(1/2). Wet values were significantly higher at 1.02±0.06 (p<0.05). KIC of dry beams varied from 0.85±0.08 at 5% QAMs to 0.49±0.05 at 15% QAMs. Wet beams gave KIC values of 1.02±0.06 MPa m(1/2) that fell to 0.23±0.01 at 15% QAMs. Addition of 10% QAMs increased the degree of conversion of unfilled resins, but lowered wet toughness and UTS; addition of 15% QAMs lowered the mechanical properties of wet resins below acceptable levels. Copyright © 2014 Academy of Dental Materials. All rights reserved.

Evaluating Corrosion in SAVY Containers using Non-Destructive Techniques

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davenport, Matthew Nicholas; Vaidya, Rajendra U.; Abeyta, Adrian Anthony

Powerpoint presentation on Ultrasonic and Eddy Current NDT; UT Theory; Eddy current (ECA): How it works; Controlled Corrosion at NM Tech; Results – HCl Corrosion; Waveform Data for 10M HCl; Accuracy Statistics; Results – FeCl 3 Pitting; Waveforms for Anhydrous FeCl 3; Analyzing Corroded Stainless Steel 316L Plates; 316L Plate to Imitate Pitting; ECA Pit Depth Calibration Curve; C Scan Imaging; UT Pit Detection; SST Containers: Ultrasonic (UT) vs. CMM; UT Data Analysis; UT Conclusions and Observations; ECA Conclusions; Automated System Vision.

Modelling and optimising of physicochemical features of walnut-oil beverage emulsions by implementation of response surface methodology: effect of preparation conditions on emulsion stability.

PubMed

Homayoonfal, Mina; Khodaiyan, Faramarz; Mousavi, Mohammad

2015-05-01

The major purpose of this study is to apply response surface methodology to model and optimise processing conditions for the preparation of beverage emulsions with maximum emulsion stability and viscosity, minimum particle size, turbidity loss rate, size index and peroxide value changes. A three-factor, five-level central composite design was conducted to estimate the effects of three independent variables: ultrasonic time (UT, 5-15 min), walnut-oil content (WO, 4-10% (w/w)) and Span 80 content (S80, 0.55-0.8). The results demonstrated the empirical models were satisfactorily (p < 0.0001) fitted to the experimental data. Evaluation of responses by analysis of variance indicated high coefficient determination values. The overall optimisation of preparation conditions was an UT of 14.630 min, WO content of 8.238% (w/w), and S80 content of 0.782% (w/w). Under this optimum region, responses were found to be 219.198, 99.184, 0.008, 0.008, 2.43 and 16.65 for particle size, emulsion stability, turbidity loss rate, size index, viscosity and peroxide value changes, respectively. Copyright © 2014 Elsevier Ltd. All rights reserved.

Chemical Tracers as an Indicator of Transport in the UT/LS

NASA Astrophysics Data System (ADS)

Moore, F. L.; Hurst, D. F.; Elkins, J. W.; Nance, J. D.; Dutton, G. S.; Hall, B. D.

2009-12-01

Previous airborne studies have proven the scientific value of chemical tracers in examining transport of the Upper Troposphere and Lower Stratosphere (UT/LS). ESRL scientists operated two airborne gas chromatographs on the NCAR G-V during the NSF sponsored Stratosphere-Troposphere Analyses of Regional Transport START-08 campaign over the midlatitudes of central North America. The Unmanned aircraft systems Chromatograph for Atmospheric Trace Species (UCATS) is comprised of a two-channel electron capture detection-gas chromatograph (ECD-GC), an ozone absorption photometer, and a water vapor tunable diode laser spectrometer. It measures N2O and SF6 every 70 seconds on one EC-GC channel, and H2, CO, and CH4 every 140 seconds on the second channel. PAN and Trace Hydrohalocarbon ExpeRiment (PANTHER) is a six-channel gas chromatograph with four ECD-GC channels and two mass selective detector-gas chromatograph (MSD-GC) channels that double the sampling rate to 180 seconds by using two traps and columns. The ECD-GC channels measure N2O, SF6, CFC-11, CFC-12, halon-1211, and PAN once every 70 seconds, H2, CH4, and CO once every 140 seconds. The two MSD-GC channels measure methyl halides (CH3I, CH3Cl, CH3I), HCFCs (22, 141b, 142b), HFC-134a, sulfur gases (COS and CS2) once every 180 seconds. These data represent a diversity of atmospheric lifetimes and are useful in examining transport in UT/LS. One example is the tracer-tracer correlation plot of N2O versus SF6, which shows three distinction regions of transport, LS, tropospause transition, and UT. Tropospheric gradients for both gases are apparent in the UT region. Other correlations will be shown in this presentation. A comparison of common species measured between UCATS and PANTHER shows a better than one percent agreement between the two instruments.

Cultivar x binary mixture interaction effect on agronomic traits in orchardgrass

USDA-ARS?s Scientific Manuscript database

A study was conducted to evaluate and characterize the agronomic value, including dry matter yield and forage quality of 25 orchardgrass cultivars grown in monoculture and binary mixtures with alfalfa under supplemental irrigation from 2009 to 2012 at a Millville, UT, field site. Orchardgrass monoc...

Genotype by environment interaction effects of propagation and defoliation on meadow bromegrass

USDA-ARS?s Scientific Manuscript database

Sixty-three meadow bromegrass (Bromus riparius Rehm.) half-sib families were evaluated over two years at Millville, UT location for biomass production and nutritive value. Families were evaluated under either space-plant or sward conditions combined with either grazed or cut management. The objectiv...

Diuresis and reduced urinary osmolality in rats produced by small-molecule UT-A-selective urea transport inhibitors.

PubMed

Esteva-Font, Cristina; Cil, Onur; Phuan, Puay-Wah; Su, Tao; Lee, Sujin; Anderson, Marc O; Verkman, A S

2014-09-01

Urea transport (UT) proteins of the UT-A class are expressed in epithelial cells in kidney tubules, where they are required for the formation of a concentrated urine by countercurrent multiplication. Here, using a recently developed high-throughput assay to identify UT-A inhibitors, a screen of 50,000 synthetic small molecules identified UT-A inhibitors of aryl-thiazole, γ-sultambenzosulfonamide, aminocarbonitrile butene, and 4-isoxazolamide chemical classes. Structure-activity analysis identified compounds that inhibited UT-A selectively by a noncompetitive mechanism with IC50 down to ∼1 μM. Molecular modeling identified putative inhibitor binding sites on rat UT-A. To test compound efficacy in rats, formulations and administration procedures were established to give therapeutic inhibitor concentrations in blood and urine. We found that intravenous administration of an indole thiazole or a γ-sultambenzosulfonamide at 20 mg/kg increased urine output by 3-5-fold and reduced urine osmolality by ∼2-fold compared to vehicle control rats, even under conditions of maximum antidiuresis produced by 1-deamino-8-D-arginine vasopressin (DDAVP). The diuresis was reversible and showed urea > salt excretion. The results provide proof of concept for the diuretic action of UT-A-selective inhibitors. UT-A inhibitors are first in their class salt-sparing diuretics with potential clinical indications in volume-overload edemas and high-vasopressin-associated hyponatremias. © FASEB.

Movie Smoking, Movie Horror, and Urge to Smoke

PubMed Central

SARGENT, James D.; MARUSKA, Karin; MORGENSTERN, Matthis; ISENSEE, Barbara; HANEWINKEL, Reiner

2010-01-01

It is known that exposure to smoking cues increases urge to smoke (UTS), but little is known about other media factors that might also increase UTS. We hypothesized that horror/thriller movies might also increase UTS by increasing negative affect. We surveyed 536 movie patrons who were smokers aged 18 years or older. Subjects had exited 26 movies, of which 12 contained smoking and two were horror films, one with and one without smoking. We used random effects regression to assess the association between exposure to movie smoking, movie horror, both and UTS, controlling for confounding factors. Median age was 26 years and 52% were female. Mean UTS was 5.9, 6.6, 6.6, and 8.7 for smokers exiting movies without smoking, with smoking, horror without smoking and horror with smoking respectively. Smoking in movies was associated with a significantly higher UTS (0.63 [95% CI 0.31–0.94]). Horror with smoking increased UTS by 2.8 points (95% C.I. 2.3, 3.5); the horror without smoking estimate was 0.88, but not statistically significant. This short report offers preliminary evidence that movie horror as one factor besides visual smoking cues that could increase UTS in a community setting. PMID:20301876

Movie smoking, movie horror, and urge to smoke.

PubMed

Sargent, James D; Maruska, Karin; Morgenstern, Matthis; Isensee, Barbara; Hanewinkel, Reiner

2009-01-01

It is known that exposure to smoking cues increases urge to smoke (UTS), but little is known about other media factors that might also increase UTS. We hypothesized that horror/ thriller movies might also increase UTS by increasing negative affect. We surveyed 536 movie patrons who were smokers aged 18 years or older. Subjects had exited 26 movies, of which 12 contained smoking and two were horrorfilms, one with and one without smoking. We used random effects regression to assess the association between exposure to movie smoking, movie horror, both and UTS, controlling for confounding factors. Median age was 26 years and 52% were female. Mean UTS was 5.9, 6.6, 6.6, and 8.7 for smokers exiting movies without smoking, with smoking, horror without smoking and horror with smoking respectively. Smoking in movies was associated with a significantly higher UTS (0.63 [95% CI 0.31-0.94]). Horror with smoking increased UTS by 2.8 points (95% C.I. 2.3, 3.5); the horror without smoking estimate was 0.88, but not statistically significant. This short report offers preliminary evidence that movie horror as one factor besides visual smoking cues that could increase UTS in a community setting.

Simultaneous Strength-Ductility Enhancement of a Nano-Lamellar AlCoCrFeNi2.1 Eutectic High Entropy Alloy by Cryo-Rolling and Annealing.

PubMed

Bhattacharjee, T; Wani, I S; Sheikh, S; Clark, I T; Okawa, T; Guo, S; Bhattacharjee, P P; Tsuji, N

2018-02-19

Nano-lamellar (L1 2  + B2) AlCoCrFeNi 2.1 eutectic high entropy alloy (EHEA) was processed by cryo-rolling and annealing. The EHEA developed a novel hierarchical microstructure featured by fine lamellar regions consisting of FCC lamellae filled with ultrafine FCC grains (average size ~200-250 nm) and B2 lamellae, and coarse non-lamellar regions consisting of ultrafine FCC (average size ~200-250 nm), few coarse recrystallized FCC grains and rather coarse unrecrystallized B2 phase (~2.5 µm). This complex and hierarchical microstructure originated from differences in strain-partitioning amongst the constituent phases, affecting the driving force for recrystallization. The hierarchical microstructure of the cryo-rolled and annealed material resulted in simultaneous enhancement in strength (Yield Strength/YS: 1437 ± 26 MPa, Ultimate Tensile Strength/UTS: 1562 ± 33 MPa) and ductility (elongation to failure/e f  ~ 14 ± 1%) as compared to the as-cast as well as cold-rolled and annealed materials. The present study for the first time demonstrated that cryo-deformation and annealing could be a novel microstructural design strategy for overcoming strength-ductility trade off in multiphase high entropy alloys.

Improving the fracture toughness and the strength of epoxy using nanomaterials--a review of the current status.

PubMed

Domun, N; Hadavinia, H; Zhang, T; Sainsbury, T; Liaghat, G H; Vahid, S

2015-06-21

The incorporation of nanomaterials in the polymer matrix is considered to be a highly effective technique to improve the mechanical properties of resins. In this paper the effects of the addition of different nanoparticles such as single-walled CNT (SWCNT), double-walled CNT (DWCNT), multi-walled CNT (MWCNT), graphene, nanoclay and nanosilica on fracture toughness, strength and stiffness of the epoxy matrix have been reviewed. The Young's modulus (E), ultimate tensile strength (UTS), mode I (GIC) and mode II (GIIC) fracture toughness of the various nanocomposites at different nanoparticle loadings are compared. The review shows that, depending on the type of nanoparticles, the integration of the nanoparticles has a substantial effect on mode I and mode II fracture toughness, strength and stiffness. The critical factors such as maintaining a homogeneous dispersion and good adhesion between the matrix and the nanoparticles are highlighted. The effect of surface functionalization, its relevancy and toughening mechanism are also scrutinized and discussed. A large variety of data comprised of the mechanical properties of nanomaterial toughened composites reported to date has thus been compiled to facilitate the evolution of this emerging field, and the results are presented in maps showing the effect of nanoparticle loading on mode I fracture toughness, stiffness and strength.

Further development of chemical vapor deposition process for production of large diameter carbon-base monofilaments

NASA Technical Reports Server (NTRS)

Hough, R. L.; Richmond, R. D.

1974-01-01

The development of large diameter carbon-base monofilament in the 50 micron to 250 micron diameter range using the chemical vapor deposition process is described. The object of this program was to determine the critical process variables which control monofilament strength, monofilament modulus, and monofilament diameter. It was confirmed that wide scatter in the carbon substrate strength is primarily responsible for the scatter in the monofilament strength. It was also shown through etching experiments that defective substrate surface conditions which can induce low strength modular growth in the monofilament layers are best controlled by processing improvements during the synthesis of the substrate. Modulus was found to be linearily proportional to monofilament boron content. Filament modulus was increased to above 27.8MN/sq cm but only by a considerable increase in monofilament boron content to 60 wt. % or more. Monofilament diameter depended upon dwell time in the synthesis apparatus. A monofilament was prepared using these findings which had the combined properties of a mean U.T.S. of 398,000 N/sq cm, a modulus of 18.9 MN/sq cm (24,000,000 psi), and a diameter of 145 microns. Highest measured strength for this fiber was 451,000 N/sq cm (645,000 psi).

Role of Uremic Toxins for Kidney, Cardiovascular, and Bone Dysfunction.

PubMed

Fujii, Hideki; Goto, Shunsuke; Fukagawa, Masafumi

2018-05-16

With decreasing kidney function, cardiovascular disease (CVD) and mineral bone disorders frequently emerge in patients with chronic kidney disease (CKD). For these patients, in addition to the traditional risk factors, non-traditional CKD-specific risk factors are also associated with such diseases and conditions. One of these non-traditional risk factors is the accumulation of uremic toxins (UTs). In addition, the accumulation of UTs further deteriorates kidney function. Recently, a huge number of UTs have been identified. Although many experimental and clinical studies have reported associations between UTs and the progression of CKD, CVD, and bone disease, these relationships are very complex and have not been fully elucidated. Among the UTs, indoxyl sulfate, asymmetric dimethylarginine, and p -cresylsulfate have been of particular focus, up until now. In this review, we summarize the pathophysiological influences of these UTs on the kidney, cardiovascular system, and bone, and discuss the clinical data regarding the harmful effects of these UTs on diseases and conditions.

Effects of alloying element on weld characterization of laser-arc hybrid welding of pure copper

NASA Astrophysics Data System (ADS)

Hao, Kangda; Gong, Mengcheng; Xie, Yong; Gao, Ming; Zeng, Xiaoyan

2018-06-01

Effects of alloying elements of Si and Sn on weld characterizations of laser-arc hybrid welded pure copper (Cu) with thickness of 2 mm was studied in detail by using different wires. The weld microstructure was analyzed, and the mechanical properties (micro-hardness and tensile property), conductivity and corrosion resistance were tested. The results showed that the alloying elements benefit the growth of column grains within weld fusion zone (FZ), increase the ultimate tensile strength (UTS) of the FZ and weld corrosion resistance, and decrease weld conductivity. The mechanisms were discussed according to the results.

SU-F-19A-07: Is a Day30 Scan Necessary to Evaluate Activity-Based Regulatory Compliance in Permanent Interstitial Brachytherapy for Prostate Cancer?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kapur, P; Ford, J; Moghanaki, D

Purpose: To evaluate the Medical Event (ME) criteria for I-125 prostate implants based on the assessment of post implant dosimetry on “Day0”/“Day30” imaging. The new ME criteria do not mandate a timeframe for this assessment. The compliance criteria are: more than 80% of the activity from the written directive for treatment site (TS) must be implanted inside TS, and doses to 1cc of either uninvolved rectum (D1-UR) or uninvolved bladder (D1-UB), or 2cc of other non-specified tissue (D2-UT) must be less than 150% of the planned dose. Methods: “Day0”/“Day30” post-implant analyses for 25 patients were evaluated. Treatment plans had amore » peripheral loading pattern with 2 core needles placed at least 10 mm away from urethra, with several seeds planned outside of the prostate for adequate target coverage. TS were a uniform 5 mm expansion of the prostate, except posteriorly (no expansion). Results: “Day0”/“Day30”analyses found no MEs. The relative changes for D1-UR, D1-UB, and D2-UT were (ranges): [−37.0, 38.2]%, [−96.5, 74.7]%, and [−41.2, 37.7]%. Furthermore, changes did not correlate with prostate volume changes of −18.7% [σ:16.0%, range:−60.5%, +6.4%]. These unfavorable changes did not lead to ME at “Day30” because these values were generally well below 150% at “Day0”. However, D2-UT dose values exceeded those for D1-UR and D1-UB at both “Day0”/“Day30”. Conclusion: The total activity was relatively insensitive to changes in target volume from “Day0” to ”Day30”. The dose metrics of interest, albeit susceptible to large, often unfavorable changes, remained less than the 150% threshold. Data from this study suggest that “Day0” can be used for the regulatory compliance evaluation. However, further evaluation at “Day30” is advisable if D2-UT is 110% or above (based on the largest D2-UT increase of 37.7% observed in this patient population). Future rigorous statistical analysis of a larger cohort will afford a refinement of this recommendation.« less

Alternative channels for urea in the inner medulla of the rat kidney.

PubMed

Nawata, C Michele; Dantzler, William H; Pannabecker, Thomas L

2015-12-01

The ascending thin limbs (ATLs) and lower descending thin limbs (DTLs) of Henle's loop in the inner medulla of the rat are highly permeable to urea, and yet no urea transporters have been identified in these sections. We hypothesized that novel, yet-unidentified transporters in these tubule segments could explain the high urea permeability. cDNAs encoding for Na(+)-glucose transporter 1a (SGLT1a), Na(+)-glucose transporter 1 (NaGLT1), urea transporter (UT)-A2c, and UT-A2d were isolated and cloned from the Munich-Wistar rat inner medulla. SGLT1a is a novel NH2-terminal truncated variant of SGLT1. NaGLT1 is a Na(+)-dependent glucose transporter primarily located in the proximal tubules and not previously described in the thin limbs. UT-A2c and UT-A2d are novel variants of UT-A2. UT-A2c is truncated at the COOH terminus, and UT-A2d has one exon skipped. When rats underwent water restriction for 72 h, mRNA levels of SGLT1a increased in ATLs, NaGLT1 levels increased in both ATLs and DTLs, and UT-A2c increased in ATLs. [(14)C]urea uptake assays performed on Xenopus oocytes heterologously expressing these proteins revealed that despite having structural differences from their full-length versions, SGLT1a, UT-A2c, and UT-A2d enhanced urea uptake. NaGLT1 also facilitated urea uptake. Uptakes were Na(+) independent and inhibitable by phloretin and/or phloridzin. Our data indicate that there are several alternative channels for urea in the rat inner medulla that could potentially contribute to the high urea permeabilities in thin limb segments. Copyright © 2015 the American Physiological Society.

Stinging Nettle (Urtica dioica L.) Attenuates FFA Induced Ceramide Accumulation in 3T3-L1 Adipocytes in an Adiponectin Dependent Manner.

PubMed

Obanda, Diana N; Zhao, Peng; Richard, Allison J; Ribnicky, David; Cefalu, William T; Stephens, Jacqueline M

2016-01-01

Excess dietary lipids result in the accumulation of lipid metabolites including ceramides that can attenuate insulin signaling. There is evidence that a botanical extract of Urtica dioica L. (stinging nettle) improves insulin action, yet the precise mechanism(s) are not known. Hence, we examined the effects of Urtica dioica L. (UT) on adipocytes. We investigated the effects of an ethanolic extract of UT on free fatty acid (palmitic acid) induced inhibition of insulin-stimulated Akt serine phosphorylation and modulation of ceramidase expression in 3T3-L1 adipocytes. Adipocytes were exposed to excess FFAs in the presence or absence of UT. Effects on adiponectin expression, ceramidase expression, ceramidase activity, ceramide accumulation and insulin signaling were determined. As expected, FFAs reduced adiponectin expression and increased the expression of ceramidase enzymes but not their activity. FFA also induced the accumulation of ceramides and reduced insulin-stimulated phosphorylation of Akt in adipocytes. The effects of FFA were partially reversed by UT. UT enhanced adiponectin expression and ceramidase activity in the presence of excess FFAs. UT abated ceramide accumulation and increased insulin sensitivity via enhanced Akt phosphorylation. A siRNA knockdown of adiponectin expression prevented UT from exerting positive effects on ceramidase activity but not Akt phosphorylation. In adipocytes, the ability of UT to antagonize the negative effects of FFA by modulating ceramidase activity and ceramide accumulation is dependent on the presence of adiponectin. However, the ability of UT to enhance Akt phosphorylation is independent of adiponectin expression. These studies demonstrate direct effects of UT on adipocytes and suggest this botanical extract is metabolically beneficial.

Salt-sparing diuretic action of a water-soluble urea analog inhibitor of urea transporters UT-A and UT-B in rats

PubMed Central

Cil, Onur; Esteva-Font, Cristina; Tas, Sadik Taskin; Su, Tao; Lee, Sujin; Anderson, Marc O.; Ertunc, Mert; Verkman, A. S.

2015-01-01

Inhibitors of kidney urea transporter (UT) proteins have potential use as salt-sparing diuretics (‘urearetics’) with a different mechanism of action than diuretics that target salt transporters. To study UT inhibition in rats, we screened about 10,000 drugs, natural products and urea analogs for inhibition of rat UT-A1. Drug and natural product screening found nicotine, sanguinarine and an indolcarbonylchromenone with IC50 of 10–20 μM. Urea analog screening found methylacetamide and dimethylthiourea (DMTU). DMTU fully and reversibly inhibited rat UT-A1 and UT-B by a noncompetitive mechanism with IC50 of 2–3 mM. Homology modeling and docking computations suggested DMTU binding sites on rat UT-A1. Following a single intraperitoneal injection of 500 mg/kg DMTU, peak plasma concentration was 9 mM with t1/2 of about 10 hours, and a urine concentration of 20–40 mM. Rats chronically treated with DMTU had a sustained, reversible reduction in urine osmolality from 1800 to 600 mOsm, a 3-fold increase in urine output, and mild hypokalemia. DMTU did not impair urinary concentrating function in rats on a low protein diet. Compared to furosemide-treated rats, the DMTU-treated rats had greater diuresis and reduced urinary salt loss. In a model of Syndrome of Inappropriate Antidiuretic Hormone secretion, DMTU treatment prevented hyponatremia and water retention produced by water-loading in dDAVP-treated rats. Thus, our results establish a rat model of UT inhibition and demonstrate the diuretic efficacy of UT inhibition. PMID:25993324

Alternative channels for urea in the inner medulla of the rat kidney

PubMed Central

Dantzler, William H.; Pannabecker, Thomas L.

2015-01-01

The ascending thin limbs (ATLs) and lower descending thin limbs (DTLs) of Henle's loop in the inner medulla of the rat are highly permeable to urea, and yet no urea transporters have been identified in these sections. We hypothesized that novel, yet-unidentified transporters in these tubule segments could explain the high urea permeability. cDNAs encoding for Na+-glucose transporter 1a (SGLT1a), Na+-glucose transporter 1 (NaGLT1), urea transporter (UT)-A2c, and UT-A2d were isolated and cloned from the Munich-Wistar rat inner medulla. SGLT1a is a novel NH2-terminal truncated variant of SGLT1. NaGLT1 is a Na+-dependent glucose transporter primarily located in the proximal tubules and not previously described in the thin limbs. UT-A2c and UT-A2d are novel variants of UT-A2. UT-A2c is truncated at the COOH terminus, and UT-A2d has one exon skipped. When rats underwent water restriction for 72 h, mRNA levels of SGLT1a increased in ATLs, NaGLT1 levels increased in both ATLs and DTLs, and UT-A2c increased in ATLs. [14C]urea uptake assays performed on Xenopus oocytes heterologously expressing these proteins revealed that despite having structural differences from their full-length versions, SGLT1a, UT-A2c, and UT-A2d enhanced urea uptake. NaGLT1 also facilitated urea uptake. Uptakes were Na+ independent and inhibitable by phloretin and/or phloridzin. Our data indicate that there are several alternative channels for urea in the rat inner medulla that could potentially contribute to the high urea permeabilities in thin limb segments. PMID:26423860

Salt-sparing diuretic action of a water-soluble urea analog inhibitor of urea transporters UT-A and UT-B in rats.

PubMed

Cil, Onur; Esteva-Font, Cristina; Tas, Sadik Taskin; Su, Tao; Lee, Sujin; Anderson, Marc O; Ertunc, Mert; Verkman, Alan S

2015-08-01

Inhibitors of kidney urea transporter (UT) proteins have potential use as salt-sparing diuretics ('urearetics') with a different mechanism of action than diuretics that target salt transporters. To study UT inhibition in rats, we screened about 10,000 drugs, natural products and urea analogs for inhibition of rat UT-A1. Drug and natural product screening found nicotine, sanguinarine and an indolcarbonylchromenone with IC50 of 10-20 μM. Urea analog screening found methylacetamide and dimethylthiourea (DMTU). DMTU fully and reversibly inhibited rat UT-A1 and UT-B by a noncompetitive mechanism with IC50 of 2-3 mM. Homology modeling and docking computations suggested DMTU binding sites on rat UT-A1. Following a single intraperitoneal injection of 500 mg/kg DMTU, peak plasma concentration was 9 mM with t1/2 of about 10 h, and a urine concentration of 20-40 mM. Rats chronically treated with DMTU had a sustained, reversible reduction in urine osmolality from 1800 to 600 mOsm, a 3-fold increase in urine output, and mild hypokalemia. DMTU did not impair urinary concentrating function in rats on a low protein diet. Compared to furosemide-treated rats, the DMTU-treated rats had greater diuresis and reduced urinary salt loss. In a model of syndrome of inappropriate antidiuretic hormone secretion, DMTU treatment prevented hyponatremia and water retention produced by water-loading in dDAVP-treated rats. Thus, our results establish a rat model of UT inhibition and demonstrate the diuretic efficacy of UT inhibition.

Stinging Nettle (Urtica dioica L.) Attenuates FFA Induced Ceramide Accumulation in 3T3-L1 Adipocytes in an Adiponectin Dependent Manner

PubMed Central

Obanda, Diana N.; Zhao, Peng; Richard, Allison J.; Ribnicky, David; Cefalu, William T.; Stephens, Jacqueline M.

2016-01-01

Objective Excess dietary lipids result in the accumulation of lipid metabolites including ceramides that can attenuate insulin signaling. There is evidence that a botanical extract of Urtica dioica L. (stinging nettle) improves insulin action, yet the precise mechanism(s) are not known. Hence, we examined the effects of Urtica dioica L. (UT) on adipocytes. Research Design We investigated the effects of an ethanolic extract of UT on free fatty acid (palmitic acid) induced inhibition of insulin-stimulated Akt serine phosphorylation and modulation of ceramidase expression in 3T3-L1 adipocytes. Adipocytes were exposed to excess FFAs in the presence or absence of UT. Effects on adiponectin expression, ceramidase expression, ceramidase activity, ceramide accumulation and insulin signaling were determined. Results As expected, FFAs reduced adiponectin expression and increased the expression of ceramidase enzymes but not their activity. FFA also induced the accumulation of ceramides and reduced insulin-stimulated phosphorylation of Akt in adipocytes. The effects of FFA were partially reversed by UT. UT enhanced adiponectin expression and ceramidase activity in the presence of excess FFAs. UT abated ceramide accumulation and increased insulin sensitivity via enhanced Akt phosphorylation. A siRNA knockdown of adiponectin expression prevented UT from exerting positive effects on ceramidase activity but not Akt phosphorylation. Conclusions In adipocytes, the ability of UT to antagonize the negative effects of FFA by modulating ceramidase activity and ceramide accumulation is dependent on the presence of adiponectin. However, the ability of UT to enhance Akt phosphorylation is independent of adiponectin expression. These studies demonstrate direct effects of UT on adipocytes and suggest this botanical extract is metabolically beneficial. PMID:26939068

Enhanced micro-vibration sensitive high-damping capacity and mechanical strength achieved in Al matrix composites reinforced with garnet-like lithium electrolyte

NASA Astrophysics Data System (ADS)

Wang, Xian-Ping; Zhang, Yi; Xia, Yu; Jiang, Wei-Bing; Liu, Hui; Liu, Wang; Gao, Yun-Xia; Zhang, Tao; Fang, Qian-Feng

2017-03-01

A novel micro-vibration sensitive-type high-damping Al matrix composites reinforced with Li7- x La3Zr2- x Nb x O12 (LLZNO, x = 0.25) was designed and prepared using an advanced spark plasma sintering (SPS) technique. The damping capacity and mechanical properties of LLZNO/Al composites (LLZNO content: 0-40 wt.%) were found to be greatly improved by the LLZNO addition. The maximum damping capacity and the ultimate tensile strength (UTS) of LLZNO/Al composite can be respectively up to 0.033 and 101.2 MPa in the case of 20 wt.% LLZNO addition. The enhancement of damping and mechanical properties of the composites was ascribed to the intrinsic high-damping capacity and strengthening effects of hard LLZNO particulate. This investigation provides a new insight to sensitively suppress micro-vibration of payloads in the aerospace environment.

The Early Spectral Evolution of the Classical Nova ASASSN-15th in M33

NASA Astrophysics Data System (ADS)

Wagner, R. Mark; Neric, Marko; Darnley, Matt J.; Williams, Steven; Starrfield, Sumner; Woodward, Charles E.; Prieto, Jose Luis

2016-06-01

During the course of the All Sky Automated Survey for SuperNovae (ASAS-SN) a new transient source designated ASASSN-15th was identified on images of the nearby galaxy M33 obtained with the 14 cm Brutus telescope in Haleakala, Hawaii on 2015 Dec 1.4 UT at V ~ 16.5 mag. Given the location of the transient in M33 and its apparent V magnitude at discovery, the implied absolute visual magnitude was about -8.5 mag suggesting that the transient was a new classical nova outburst in M33. Optical spectroscopy obtained by us on 2015 Dec 2.3 showed broad emission lines of Balmer, Fe II, and Na I D with P Cygni-type line profiles superposed on a blue continuum. The spectrum was consistent with a Fe II-type classical nova in M33 discovered early in the outburst. Subsequent spectra obtained by us on 2015 Dec 10.9 UT showed significant evolution since our first spectrum in that the deep P Cygni-type line profiles seen earlier were now extremely shallow or had almost completely disappeared with the emission component growing in strength. Additional emission lines from O I, Si II, and possibly He I were also present. We obtained optical spectroscopy of ASASSN-15th on 17 epochs between 2015 Dec 1 and 2016 Feb 11 UT with the 2.4 m Hiltner telescope (+OSMOS) of the MDM Observatory, the 2 m fully robotic Liverpool Telescope (+SPRAT), and the 2 x 8.4 m Large Binocular Telescope (+MODS). We will present our spectroscopy and discuss the early evolution of ASASSN-15th in the context of Galactic Fe II-class novae.

Scapular muscle activity in a variety of plyometric exercises.

PubMed

Maenhout, Annelies; Benzoor, Maya; Werin, Maria; Cools, Ann

2016-04-01

Plyometric shoulder exercises are commonly used to progress from slow analytical strength training to more demanding high speed power training in the return to play phase after shoulder injury. The aim of this study was first, to investigate scapular muscle activity in plyometric exercises to support exercise selection in practice and second, to enhance understanding of how scapular muscles are recruited during the back and forth movement phase of these exercises. Thirty-two healthy subjects performed 10 plyometric exercises while surface EMG-activity of the scapular muscles (upper (UT), middle (MT) and lower trapezius (LT) and serratus anterior (SA)) was registered. A high speed camera tracked start and end of the back and forth movement. Mean scapular EMG activity during the 10 exercises ranged from 14.50% to 76.26%MVC for UT, from 15.19% to 96.55%MVC for MT, from 13.18% to 94.35%MVC for LT and from 13.50% to 98.50%MVC for SA. Anova for repeated measures showed significant differences in scapular muscle activity between exercises (p<0.001) and between the back and forth movement (p<0.001) within exercises. Plyometric shoulder exercises require moderate (31-60%MVC) to high (>60%MVC) scapular muscle activity. Highest MT/LT activity was present in prone plyometric external rotation and flexion. Highest SA activity was found in plyometric external rotation and flexion with Xco and plyometric push up on Bosu. Specific exercises can be selected that recruit minimal levels of UT activity (<15%): side lying plyometric external rotation and horizontal abduction or plyometric push up on the Bosu. The results of this study support exercise selection for clinical practice. Copyright © 2016 Elsevier Ltd. All rights reserved.

Hot Press as a Sustainable Direct Recycling Technique of Aluminium: Mechanical Properties and Surface Integrity.

PubMed

Yusuf, Nur Kamilah; Lajis, Mohd Amri; Ahmad, Azlan

2017-08-03

Meltless recycling technique has been utilized to overcome the lack of primary resources, focusing on reducing the usage of energy and materials. Hot press was proposed as a novel direct recycling technique which results in astoundingly low energy usage in contrast with conventional recycling. The aim of this study is to prove the technical feasibility of this approach by characterizing the recycled samples. For this purpose, AA6061 aluminium chips were recycled by utilizing hot press process under various operating temperature (T s = 430, 480, and 530 °C) and holding times (t s = 60, 90, and 120 min). The maximum mechanical properties of recycled chip are Ultimate tensile strength (UTS) = 266.78 MPa, Elongation to failure (ETF) = 16.129%, while, for surface integrity of the chips, the calculated microhardness is 81.744 HV, exhibited at T s = 530 °C and t s = 120 min. It is comparable to theoretical AA6061 T4-temper where maximum UTS and microhardness is increased up to 9.27% and 20.48%, respectively. As the desired mechanical properties of forgings can only be obtained by means of a final heat treatment, T5-temper, aging after forging process was employed. Heat treated recycled billet AA6061 (T5-temper) are considered comparable with as-received AA6061 T6, where the value of microhardness (98.649 HV) at 175 °C and 120 min of aging condition was revealed to be greater than 3.18%. Although it is quite early to put a base mainly on the observations in experimental settings, the potential for significant improvement offered by the direct recycling methods for production aluminium scrap can be clearly demonstrated. This overtures perspectives for industrial development of solid state recycling processes as environmentally benign alternatives of current melting based practices.

Upregulation of erythropoietin receptor in UT-7/EPO cells inhibits simulated microgravity-induced cell apoptosis

NASA Astrophysics Data System (ADS)

Zou, Li-xue; Cui, Shao-yan; Zhong, Jian; Yi, Zong-chun; Sun, Yan; Fan, Yu-bo; Zhuang, Feng-yuan

2011-07-01

Hematopoietic progenitor cell proliferation can be altered in either spaceflight or under simulated microgravity experiments on the ground, however, the underlying mechanism remains unknown. Our previous study showed that exposure of the human erythropoietin (EPO)-dependent leukemia cell line UT-7/EPO to conditions of simulated microgravity significantly inhibited the cellular proliferation rate and induced cell apoptosis. We postulated that the downregulation of the erythropoietin receptor (EPOR) expression in UT-7/EPO cells under simulated microgravity may be a possible reason for microgravity triggered apoptosis. In this paper, a human EPOR gene was transferred into UT-7/EPO cells and the resulting expression of EPOR on the surface of UT-7/EPO cells increased approximately 61% ( p < 0.05) as selected by the antibiotic G418. It was also shown through cytometry assays and morphological observations that microgravity-induced apoptosis markedly decreased in these UT-7/EPO-EPOR cells. Thus, we concluded that upregulation of EPOR in UT-7/EPO cells could inhibit the simulated microgravity-induced cell apoptosis in this EPO dependent cell line.

Consolidation of commercial pure aluminum particles by hot ECAP

NASA Astrophysics Data System (ADS)

Gudimetla, Kondaiah; Kumar, S. Ramesh; Ravisankar, B.; Prasad Prathipati, R.; Kumaran, S.

2018-03-01

In the current study undertaken, aluminum particles of commercial purity grade were compacted using hot ECAP. Investigation of the structural evolution and mechanical properties was done. Measurements of the densities of the samples was done for the purpose of evaluation the performance of the consolidation process. A tensile strength (UTS) of 98 MPa (after first pass) was obtained under tensile loads and the percent elongation to fracture was found to be 5.5%, which indicated good tensile strength and ductility as compared to the commercial pure Al powders consolidated by ambient temperature ECAP and other techniques. The relative density and Rockwell hardness (HRB) of compacts (after first pass) was 99% and 42 respectively. This is indisputable proof for establishing the compatibility of ECAP in the matter of producing bulk materials. Characterization of the material microstructure and fracture behavior was done through use of optical and scanning electron microscopy (SEM). The Al powders consolidated at 400°C through ECAP process, exhibited the best combination of yield strength and ductility and hence hot ECAP is suitable method for consolidation of micro powders.

High temperature tensile behavior and microstructure of Al-SiC nanocomposite fabricated by mechanical milling and hot extrusion technique

NASA Astrophysics Data System (ADS)

Soltani, Mohammadreza; Atrian, Amir

2018-02-01

This paper investigates the high-temperature tensile behavior of Al-SiC nanocomposite reinforced with 0, 1.5, and 3 vol% SiC nano particles. To fabricate the samples, SiC nano reinforcements and aluminum (Al) powders were milled using an attritor milling and then were cold pressed and hot extruded at 500 °C. Afterward, mechanical and microstructural characteristics were studied in different temperatures. To this end, tensile and compressive tests, micro-hardness test, microscopic examinations, and XRD analysis were performed. The results showed significant improvement of mechanical properties of Al-SiC nanocomposite in room temperature including 40% of ultimate tensile strength (UTS), 36% of ultimate compressive strength (UCS), and 44% of micro-hardness. Moreover, performing tensile tests at elevated temperatures (up to 270 °C) decreased the tensile strength by about 53%, 46%, and 45% for Al-0 vol% SiC, Al-1.5 vol% SiC, and Al-3 vol% SiC, respectively. This temperature rise also enhanced the elongation by about 11% and 133% for non-reinforced Al and Al-3 vol% SiC, respectively.

Multilayer Mg-Stainless Steel Sheets, Microstructure, and Mechanical Properties

NASA Astrophysics Data System (ADS)

Inoue, Junya; Sadeghi, Alireza; Kyokuta, Nobuhiko; Ohmori, Toshinori; Koseki, Toshihiko

2017-05-01

Different multilayer Mg AZ31 and SS304L steel sheet combinations were prepared with different volume fractions of Mg. Isolated stress-strain curves of the Mg layers showed significant improvements in the strength and elongation of multilayer samples. Results indicated that in the most extreme situation with the lowest Mg volume fraction ( V f = 0.39), the ultimate strength was increased by 25 pct to 370 MPa and the elongation was improved by 70 pct to 0.34. Investigation of the fracture surface showed that failure occurs by the coalescence of cracks close to the interface region. The improved strength of the multilayer samples was due to the combined effect of surface crack prevention by the steel layer and the higher work-hardening rate caused by the possible increased activity of non-basal systems. It is suggested that the stronger work-hardening behavior and the enhanced activity of non-basal systems in the multilayer samples were due to the formation of new stress components in the transverse direction. The larger the volume fraction of steel in the multilayer, the longer the distance remaining unstrained before the UTS.

Impact of aerobic and anaerobic exercise training on oxidative stress and antioxidant defense in athletes.

PubMed

Park, Song-Young; Kwak, Yi-Sub

2016-04-01

Exercise mediates an excessive free radical production leading to oxidative stress (OS). The body has natural antioxidant systems that help decrease OS, and these systems may be enhanced with exercise training. However, only a few studies have investigated the differences in resting OS and antioxidant capacity (AOC) between aerobically trained athletes (ET), anaerobically trained athletes (RT), and untrained individuals (UT). Therefore, this study sought to investigate the resting and postexercise OS and AOC in ET, RT, and UT. Sixty healthy young males (26.6±0.8 yr) participated in this study. Subjects were divided into three groups, ET, RT, and UT by distinct training background. Resting plasma malondialdehyde (MDA) and protein carbonyls (PC) were not significantly different in ET, RT, and UT. However, MDA and PC were significantly increased following a graded exercise test (GXT) in UT but not in ET and RT. Resting total antioxidant capacity (TAC) levels and TAC were not different in ET, RT, and UT. Interestingly, TAC levels significantly decreased after the GXT in all groups. Additionally, UT showed lower post-exercise TAC levels compared to ET and RT. These results showed that ET, RT, and UT have similar OS and AOC at rest. However, both ET and RT have greater AOC against exercise mediated OS compared to UT. These findings may explain, at least in part, why both aerobic and anaerobic types of exercise training improve redox balance. However, it appears there is no specific exercise type effect in terms of redox balance.

Data and Tools | Research Site Name | NREL

Science.gov Websites

aliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo laboris nisi ut aliquip ex ea commodo consequat. Research Topic 1 Lorem Ipsum Tool 1 Lorem Ipsum Facility

78 FR 49116 - Modification of Class E Airspace; Brigham City, UT

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-13

...; telephone (425) 203-4537. SUPPLEMENTARY INFORMATION: History On June 5, 2013, the FAA published in the... extending upward from 700 feet or more above the surface of the earth. * * * * * ANM UT E5 Brigham City, UT...

Regions of conservation and divergence in the 3' untranslated sequences of genomic RNA from Ross River virus isolates.

PubMed

Faragher, S G; Dalgarno, L

1986-07-20

The 3' untranslated (UT) sequences of the genomic RNAs of five geographic variants of the alphavirus Ross River virus (RRV) were determined and compared with the 3' UT sequence of RRV T48, the prototype strain. Part of the 3' UT region of Getah virus, a close serological relative of RRV, was also sequenced. The RRV 3' UT region varies markedly in length between variants. Large deletions or insertions, sequence rearrangements and single nucleotide substitutions are observed. A sequence tract of 49 to 58 nucleotides, which is repeated as four blocks in the RRV T48 3' UT region, occurs only once in the 3' UT region of one RRV strain (NB5092), indicating that the existence of repeat sequence blocks is not essential for RRV replication. However, the precise sequence of the 3' proximal copy of the repeat block and its position relative to the poly(A) tail were identical in all RRV isolates examined, suggesting that it has an important role in RRV replication. Nucleotide substitutions between RRV variants are distributed non-randomly along the length of the 3' UT region. The sequence of 120 to 130 nucleotides adjacent to the poly(A) tail is strongly conserved. Getah virus RNA contains three repeat sequence blocks in the 3' UT region. These are similar in sequence to those in RRV RNA but differ in their arrangement. Homology between the RRV and Getah 3' UT sequences is greatest in the 3' proximal repeat sequence block that shows three differences in 49 nucleotides. The 3' proximal repeat in Getah RNA occurs at the same position, relative to the poly(A) tail, as in all RRV variants. The RRV and Getah virus 3' UT sequences show extensive homology in the region between the 3' proximal repeat and the poly(A) tail but, apart from the repeat blocks themselves, they show no significant homology elsewhere.

Evidence that one is more likely to see the aurora near Moscow than near Ann Arbor

NASA Astrophysics Data System (ADS)

Liemohn, Michael; Immel, Thomas; Katus, Roxanne

We present a superposed epoch analysis of solar wind drivers and geomagnetic index responses during magnetic storms, categorized as a function of universal time (UT) of the storm peak, to investigate the dependency of storm intensity on UT. Storms with Dst minimum less than - 100 nT were identified in the 1970 - 2012 era (totaling 310 events), covering four solar cycles. The storms were classified into 6 groups based on the UT of the minimum Dst (36 to 82 events per bin), then each grouping was superposed on a timeline that aligns the time of the minimum Dst. Fifteen different quantities were considered, seven solar wind parameters and eight activity indices derived from ground-based magnetometers. Statistical analyses of the superposed means against each other (between the different UT groupings) were conducted to determine the mathematical significance of similarities and differences in the time series plots. It was found that most of the solar wind parameters have essentially no significant difference between the UT groupings, as expected. The exception is solar wind velocity, which appears to be bifurcated into two levels with three of the UT groupings systematically faster than the other three (although, interestingly, not three consecutive UT bins). The geomagnetic activity indices, however, all show statistically significant differences with UT during the main phase and/or early recovery phase. Specifically, the 16, 20, and 00 UT groupings are stronger storms than those in the other UT bins. That is, storms are stronger when the Asian sector is on the nightside (American sector on the dayside) during the main phase. An inference from these findings, therefore, is that one is more likely to see the aurora near Moscow in Russia than near Ann Arbor, Michigan in the United States, even though these two cities have very similar magnetic latitudes (52 degrees).

Applying Public Health Screening Criteria: How Does Universal Newborn Screening Compare to Universal Tumor Screening for Lynch Syndrome in Adults with Colorectal Cancer?

PubMed Central

Cragun, Deborah; DeBate, Rita D.; Pal, Tuya

2014-01-01

Institutions have increasingly begun to adopt universal tumor screening (UTS) programs whereby tumors from all newly diagnosed patients with colorectal cancer (CRC) are screened to identify who should be offered germline testing for Lynch syndrome (the most common cause of hereditary CRC). Given limited information about the impact of universal screening programs to detect hereditary disease in adults, we apply criteria used to evaluate public health screening programs and compares and contrasts UTS with universal newborn screening (NBS) for the purpose of examining ethical implications and anticipating potential outcomes of UTS. Both UTS and a core set of NBS conditions clearly meet most of the Wilson and Jungner screening criteria. However, many state NBS panels include additional conditions that do not meet several of these criteria, and there is currently insufficient data to confirm that UTS meets some of these criteria. Comparing UTS and NBS with regard to newer screening criteria raises additional issues that require attention for both UTS and NBS. Comparisons also highlight the importance of evaluating the implementation of genomic tests to ensure or improve their effectiveness at reducing morbidity and mortality while minimizing potential harms. PMID:25323653

Smart Textile Based on Fiber Bragg Grating Sensors for Respiratory Monitoring: Design and Preliminary Trials

PubMed Central

Ciocchetti, Marco; Massaroni, Carlo; Saccomandi, Paola; Caponero, Michele A.; Polimadei, Andrea; Formica, Domenico; Schena, Emiliano

2015-01-01

Continuous respiratory monitoring is important to assess adequate ventilation. We present a fiber optic-based smart textile for respiratory monitoring able to work during Magnetic Resonance (MR) examinations. The system is based on the conversion of chest wall movements into strain of two fiber Bragg grating (FBG) sensors, placed on the upper thorax (UT). FBGs are glued on the textile by an adhesive silicon rubber. To increase the system sensitivity, the FBGs positioning was led by preliminary experiments performed using an optoelectronic system: FBGs placed on the chest surface experienced the largest strain during breathing. System performances, in terms of respiratory period (TR), duration of inspiratory (TI) and expiratory (TE) phases, as well as left and right UT volumes, were assessed on four healthy volunteers. The comparison of results obtained by the proposed system and an optoelectronic plethysmography highlights the high accuracy in the estimation of TR, TI, and TE: Bland-Altman analysis shows mean of difference values lower than 0.045 s, 0.33 s, and 0.35 s for TR, TI, and TE, respectively. The mean difference of UT volumes between the two systems is about 8.3%. The promising results foster further development of the system to allow routine use during MR examinations. PMID:26389961

Implementation of straight and curved steel girder erection design tools construction : summary.

DOT National Transportation Integrated Search

2010-11-05

Project 0-5574 Curved Plate Girder Design for Safe and Economical Construction, resulted in the : development of two design tools, UT Lift and UT Bridge. UT Lift is a spreadsheet-based program for analyzing : steel girders during lifting while ...

Prevention of experimental diabetes by Uncaria tomentosa extract: Th2 polarization, regulatory T cell preservation or both?

PubMed

Domingues, Alexandre; Sartori, Alexandrina; Golim, Marjorie Assis; Valente, Ligia Maria Marino; da Rosa, Larissa Camargo; Ishikawa, Larissa Lumi Watanabe; Siani, Antonio Carlos; Viero, Rosa Marlene

2011-09-01

Uncaria tomentosa (Willd.) DC (Rubiaceae) is a species native to the Amazon rainforest and surrounding tropical areas that is endowed with immunomodulatory properties and widely used around the world. In this study we investigated the immunomodulatory potential of Uncaria tomentosa (UT) aqueous-ethanol extract on the progression of immune-mediated diabetes. C57BL/6 male mice were injected with MLDS (40 mg/kg) and orally treated with UT at 10-400mg/kg during 21 days. Control groups received MLDS alone or the respective dilution vehicle. Pancreatic mononuclear infiltrate and β-cell insulin content were analyzed by HE and immunohistochemical staining, respectively, and measured by digital morphometry. Lymphocyte immunophenotyping and cytokine production were determined by flow cytometry analysis. Treating the animals with 50-400mg/kg of UT caused a significant reduction in the glycemic levels, as well as in the incidence of diabetes. The morphometric analysis of insulitis revealed a clear protective effect. Animals treated with UT at 400mg/kg presented a higher number of intact islets and a significant inhibition of destructive insulitis. Furthermore, a significant protection against the loss of insulin-secreting presented β-cells was achieved, as observed by a careful immunohistochemical evaluation. The phenotypic analysis indicated that the groups treated with higher doses (100-400mg/kg) presented CD4(+) and CD8(+) T-cell values similar to those observed in healthy animals. These same higher doses also increased the number of CD4(+)CD25(+)Foxp3(+) regulatory T-cells. Moreover, the extract modulated the production of Th1 and Th2, with increased levels of IL-4 and IL-5. The extract was effective to prevent the progression of immune-mediated diabetes by distinct pathways. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

Glycogen Synthase Kinase-3 Modulates Hyperosmotic-Induced Urea Transporter A1 Relocation in the Inner Medullary Collecting Duct Cells.

PubMed

Li, Yong-Xia; Huang, Yun; Liu, Song; Mao, Yan; Yuan, Cheng-Yan; Yang, Xiao; Yao, Li-Jun

2016-01-01

Glycogen synthase kinase 3 (GSK3) regulates urine concentration by mediating the vasopressin-induced aquaporin 2 expression and water permeability, although it is unknown whether GSK3 also mediates the accumulation of the urea transporter A1 (UT-A1). The aim of this study is to investigate the effect of GSK3 on UT-A1 distribution. Mouse inner medullary collecting duct 3 cells were transfected with UT-A1-GFP construct. The stable transfected cells were cultured under hypertonic conditions, treated with GSK3 inhibitor lithium chloride, GSK3 activator, lysosome or proteasome inhibitor. The expression levels of UT-A1, GSK3, and phospho-GSK3 were analyzed using western blot. The interaction between UT-A1 and the Golgi apparatus was examined using confocal immunofluorescence microscope. The UT-A1 trafficking was examined using the biotinylation of surface membranes. UT-A1 dissociated away from the Golgi apparatus and translocated to the plasma membrane under hypertonic-NaCl and NaCl plus urea stimulation. This movement was accompanied by the increased phosphorylation of GSK3 and its localization on the cellular membrane. Moreover, these results were duplicated by treating the cells with the GSK3 inhibitor, and by contrast, were partially reversed by the GSK3 activator. Treating cells with a lysosome or proteasome inhibitor failed to attenuate the effects of hypertonic stimulus, indicating that the loss of UT-A1 from the Golgi was not due to degradation. Our results suggest that GSK3 may in part modulate the hypertonic-induced intracellular UT-A1 redistribution and its accumulation on the plasma membrane, which may constitute another mechanism by which GSK3 modulates urine concentration. © 2016 S. Karger AG, Basel.

Isometric muscle activation of the serratus anterior and trapezius muscles varies by arm position: a pilot study with healthy volunteers with implications for rehabilitation.

PubMed

Miyasaka, Junsuke; Arai, Ryuzo; Ito, Taisuke; Shingu, Nobuyuki; Hasegawa, Satoshi; Ibuki, Satoko; Ichihashi, Noriaki; Matsuda, Shuichi; Moritani, Toshio

2017-07-01

This study aimed to determine the most appropriate angle and moving direction of the arm for improving coordination of the periscapular muscles, including the serratus anterior (SA), upper trapezius (UT), middle trapezius (MT), and lower trapezius (LT). Muscle activation amplitudes were evaluated in the SA, UT, MT, and LT in 11 healthy subjects by use of surface electromyography. The subjects were asked to maintain the arm position at 5 elevated positions with maximal effort against applied manual forces, which were directed from upper to lower (test 1), lower to upper (test 2), posterior to anterior in the frontal plane and lateral to medial in the sagittal plane (test 3), and anterior to posterior in the frontal plane and medial to lateral in the sagittal plane (test 4). The relative activity of the UT with respect to the SA, MT, and LT was calculated, resulting in the UT/SA, UT/MT, and UT/LT ratios. Test 4 in all positions but 150° of elevation in the frontal plane showed high activity of the SA with a low UT/SA ratio. High MT activity with a low UT/MT ratio was observed during test 3 at the 90° elevated position, whereas high LT activity without UT hyperactivation was not found. To strengthen the periscapular muscles in the balanced condition, horizontal adduction is recommended for the SA. Horizontal abduction at the 90° elevated position should be effective for the MT. Because no technique in this study was effective for the LT, further studies are needed. Copyright © 2016 Journal of Shoulder and Elbow Surgery Board of Trustees. Published by Elsevier Inc. All rights reserved.

Urinary concentrating defect in mice with selective deletion of phloretin-sensitive urea transporters in the renal collecting duct

PubMed Central

Fenton, Robert A.; Chou, Chung-Lin; Stewart, Gavin S.; Smith, Craig P.; Knepper, Mark A.

2004-01-01

To investigate the role of inner medullary collecting duct (IMCD) urea transporters in the renal concentrating mechanism, we deleted 3 kb of the UT-A urea transporter gene containing a single 140-bp exon (exon 10). Deletion of this segment selectively disrupted expression of the two known IMCD isoforms of UT-A, namely UT-A1 and UT-A3, producing UT-A1/3-/- mice. In isolated perfused IMCDs from UT-A1/3-/- mice, there was a complete absence of phloretin-sensitive or vasopressin-stimulated urea transport. On a normal protein intake (20% protein diet), UT-A1/3-/- mice had significantly greater fluid consumption and urine flow and a reduced maximal urinary osmolality relative to wild-type controls. These differences in urinary concentrating capacity were nearly eliminated when urea excretion was decreased by dietary protein restriction (4% by weight), consistent with the 1958 Berliner hypothesis stating that the chief role of IMCD urea transport in the concentrating mechanism is the prevention of urea-induced osmotic diuresis. Analysis of inner medullary tissue after water restriction revealed marked depletion of urea in UT-A1/3-/- mice, confirming the concept that phloretin-sensitive IMCD urea transporters play a central role in medullary urea accumulation. However, there were no significant differences in mean inner medullary Na+ or Cl- concentrations between UT-A1/3-/- mice and wild-type controls, indicating that the processes that concentrate NaCl were intact. Thus, these results do not corroborate the predictions of passive medullary concentrating models stating that NaCl accumulation in the inner medulla depends on rapid vasopressin-regulated urea transport across the IMCD epithelium. PMID:15123796

Transcranial direct current stimulation versus user training on improving online myoelectric control for amputees

NASA Astrophysics Data System (ADS)

Pan, Lizhi; Zhang, Dingguo; Jiang, Ning; Sheng, Xinjun; Zhu, Xiangyang

2017-08-01

Objective. Transcranial direct current stimulation (tDCS) and user training (UT) are two types of methods to improve myoelectric control performance for amputees. In this study, we compared the independent effect between tDCS and UT, and investigated the combined effect of tDCS and UT. Approach. An online paradigm of simultaneous and proportional control (SPC) based on electromyography (EMG) was adopted. The proposed experiments were conducted on six naïve unilateral trans-radial amputees. The subjects each received three types of 20 min interventions: active tDCS with motor training (tDCS  +  UT), active tDCS with quiet sitting (tDCS), and sham tDCS with motor training (UT). The interventions were applied at one week intervals in a randomized order. The subjects performed online control of a feedback arrow with two degrees of freedom (DoFs) to accomplish target reaching motor tasks in pre-sessions and post-sessions. We compared the performance, measured by completion rate, completion time, and efficiency coefficient, between pre-sessions and post-sessions. Main results. The results showed that the intervention tDCS  +  UT and tDCS significantly improved the online SPC performance (i.e. improved the completion rate; reduced the completion time; and improved the efficiency coefficient), while intervention UT did not significantly change the performance. The results also showed that the online SPC performance after intervention tDCS  +  UT and tDCS was not significantly different, but both were significantly better than that after intervention UT. Significance. tDCS could be an effective intervention to improve the online SPC performance in a short time.

Near real-time monitoring of UT1 with geodetic VLBI

NASA Astrophysics Data System (ADS)

Haas, R.; Hobiger, T.; Sekido, M.; Koyama, Y.; Kondo, T.; Takiguchi, H.; Kurihara, S.; Kokado, K.; Tanimoto, D.; Nozawa, K.; Wagner, J.; Ritakari, J.; Mujunen, A.; Uunila, M.

2011-07-01

Geodetic VLBI is unique among the geodetic space techniques since it provides a direct connection between the international terrestrial reference frame and the international celestial reference frame. The Earth rotation angle, usually expressed as UT1, can be determined directly from geodetic VLBI observations. Accurate information about the Earth rotation angle is necessary and important for navigation purposes, in particular for satellite missions and space navigation. A near real-time knowledge of UT1 with high accuracy is therefore highly desirable. During the last few years the advances in data transfer over high-speed optical fibre lines have made it possible to electronically send the observational data from a VLBI radio telescope on one side of the globe in real-time to a VLBI correlator on the other side of the globe. Thus, data of two telescopes on opposite sides of the Earth, forming a long east-west oriented baseline, can be correlated in near real-time. Furthermore, advances in automated processing of the correlation results have made it possible to derive the Earth rotation angle UT1 in near real-time. Since 2007, the VLBI research groups in Sweden, Finland and Japan collaborate to derive UT1 in near real-time. Several dedicated so-called ultra-rapid UT1-sessions with 1-2 hours duration were performed. It was shown that final UT1-results can be derived within a few minutes after the end of an observing session (Sekido et al., 2008; Matsuzaka et al., 2008). The quality of the UT1-results is on the same level as the so-called IERS rapid solutions, but with a much lower latency (Haas et al., 2010). Recently, the ultra-rapid approach has been applied to standard 24 hour long VLBI observing sessions that are organized by the International VLBI Service for Geodesy and Astrometry (IVS). The long east-west baseline between Onsala (Sweden) and Tsukuba (Japan) is used to derive UT1 with a sliding window approach already during the ongoing IVS-session. The data processing and analysis is performed with a fully automated analysis software (Hobiger et al., 2010). We present results from the ultra-rapid UT1-sessions, both, from dedicated one-baseline sessions, as well from 24-hour ultra-rapid sessions during standard IVS-experiments. The near real-time UT1 results are compared to corresponding post-processing results, and results from independent analyses and techniques. Refrences: Sekido et al. (2008) Ultra-rapid UT1 measurements by e-VLBI, Earth Planets and Space, Vol. 60, 865-870. Matsuzaka et al. (2008) Ultra Rapid UT1 Experiment with e-VLBI, In: Proc. 5th IVS General Meeting, 68-71. Haas R et al. (2010) Ultra-Rapid DUT1-Observations with E-VLBI. Artificial Satellites, 45, 75-79. Hobiger et al. (2010) Fully automated VLBI analysis with c5++ for ultra-rapid determination of UT1, Earth Planets Space.

Knowledge Retrieval as Specialized Inference.

DTIC Science & Technology

1987-05-01

by both the Science and 0 Engineering Research Council and the Alvey Directorate under grant SERC GR/D/16062. -DISR~UtIOr s~rT EMiNT r.jAv ’r’v’vI for...Accommodating value assignments at this point facilitates the incorporation of quantifiers in Chapter 4 %S -". PLS - 20 - way. It should now be clear

The effect of nano-SiC on characteristics of ADC12/nano-SiC composite with Sr and TiB addition produced by stir casting process

NASA Astrophysics Data System (ADS)

Anne Zulfia, S.; Salshabia, Nadella; Dhaneswara, Donanta; Utomo, Budi Wahyu

2018-05-01

ADC12 reinforced nano SiC has been successfully produced by stir casting process. Nano SiC was added into ADC12 alloy varied from 0.05 to 0.3 vf-% while Al-5Ti-1B and Sr were kept constant at 0.04 and 0.02 wt-% respectively to all composites. Mg was added 10 wt% to improve reinforce's wettability. The addition of Al-5Ti-1B to the alloy was as grain refiner while Sr was added to modify Mg2Si. All composites were characterized both microstructures analysis and mechanical properties include tensile strength, hardness, wear rate, impact strength, and porosity. The highest properties of composites was obtained at 0.3 vf-% nano SiC addition with UTS of 155.4 MPa, hardness of 46.16 HRB, impact strength of 0.22 J/mm2, and wear rate of 1.71 × 10-5 mm3/m. Tensile strength and hardness increased as grain size and porosities decreased. The highest wear resistance was investigated on the composition with the highest hardness. Impact strength decreased due to increasing volume fraction of nano-SiC. The phases present in microsturucture was dominantly Mg2Si which also affected mechanical properties of these composites.

Damage assessment and progression in a polyisocyanurate-based continuous swirl mat composite

NASA Astrophysics Data System (ADS)

Worley, Darwell Carlton, II

This research conducted in conjunction with Oak Ridge National Laboratories and the Automotive Composite Consortium, ACC, was motivated by the desire to reduce vehicle weight for increased efficiency. At present, there are no databases of failure mechanisms, experimental procedures to study failure, mathematical expressions for empirical or theoretical prediction of properties of a continuous swirl mat composite, CSMC. Therefore, to contribute to the increased utilization of this class of materials the following research was performed. This research enabled the failure mechanism to be formulated, development of a method to quantify failure based on ultrasonic attenuation maps, and the prediction of the fracture toughness parameter KIC. The use of scanning electron microscopy, light microscopy, and real-time tensile loading showed that the CSMC failed in a brittle mode. These techniques also provided imaging information as to how a dominant crack propagates in the presence of a continuously swirled E-glass mat reinforcement and voids. This evaluation enabled a reconstruction of failure in order to demonstrate a possible failure mechanism. The aforementioned techniques revealed that the dominant crack follows the fiber/matrix interface, but may be influenced by the presence of voids. Voids have the tendency of luring the growing crack away from the interface. A growing crack would, however, return to a fiber/matrix interface until complete failure occurred. Another aspect of this work was the quantification of progressive damage using ultrasound. Comparisons were made between ultrasonic attenuation maps for unloaded and sequentially loaded specimens. The sequential loads were applied at different percentages of the ultimate tensile strength, UTS. This technique provided attenuation maps for a series of specimens with a controlled degree of damage, which showed an increase in attenuation with an increase in percent UTS. Fracture toughness experiments yielded an average KIC value of 17.1 MPa√m, while the prediction of the fracture toughness parameter, KIC, was achieved by combining K-solution expressions for in-line and parallel crack configurations while evaluating the needed stress, sigma, using of the "Rule of Mixtures". The average void length was used as the crack length, which was obtained by light microscopy in conjunction with NIHTM software. The predicted KIC value at 40% glass fiber and void orientations of 45°, 30° and 25° was 11.4 MPa√m, 17.0 MPa√m and 18.6 MPa√m, respectively.

A novel small-molecule thienoquinolin urea transporter inhibitor acts as a potential diuretic.

PubMed

Li, Fei; Lei, Tianluo; Zhu, Juanjuan; Wang, Weiling; Sun, Yi; Chen, Jihui; Dong, Zixun; Zhou, Hong; Yang, Baoxue

2013-06-01

Urea transporters (UTs) are a family of membrane channel proteins that are specifically permeable to urea and play an important role in intrarenal urea recycling and in urine concentration. Using an erythrocyte osmotic lysis assay, we screened a small-molecule library for inhibitors of UT-facilitated urea transport. A novel class of thienoquinolin UT-B inhibitors were identified, of which PU-14 had potent inhibition activity on human, rabbit, rat, and mouse UT-B. The half-maximal inhibitory concentration of PU-14 on rat UT-B-mediated urea transport was ∼0.8 μmol/l, and it did not affect urea transport in mouse erythrocytes lacking UT-B but inhibited UT-A-type urea transporters, with 36% inhibition at 4 μmol/l. PU-14 showed no significant cellular toxicity at concentrations up to its solubility limit of 80 μmol/l. Subcutaneous delivery of PU-14 (at 12.5, 50, and 100 mg/kg) to rats caused an increase of urine output and a decrease of the urine urea concentration and subsequent osmolality without electrolyte disturbances and liver or renal damages. This suggests that PU-14 has a diuretic effect by urea-selective diuresis. Thus, PU-14 or its analogs might be developed as a new diuretic to increase renal fluid clearance in diseases associated with water retention without causing electrolyte imbalance. PU-14 may establish 'chemical knockout' animal models to study the physiological functions of UTs.

Effects of extrusion and heat treatment on the mechanical properties and biocorrosion behaviors of a Mg-Nd-Zn-Zr alloy.

PubMed

Zhang, Xiaobo; Yuan, Guangyin; Mao, Lin; Niu, Jialin; Fu, Penghuai; Ding, Wenjiang

2012-03-01

Mechanical properties at room temperature and biocorrosion behaviors in simulated body fluid (SBF) at 37 °C of a new type of patented Mg-3Nd-0.2Zn-0.4Zr (hereafter, denoted as JDBM) alloy prepared at different extrusion temperatures, as well as heat treatment, were studied. The mechanical properties of this magnesium alloy at room temperature were improved significantly after extrusion and heat treatment compared to an as-cast alloy. The results of mechanical properties show that the yield strength (YS) decreases with increasing extrusion temperature. The tensile elongation decreases a little while the ultimate tensile strength (UTS) has no obvious difference. The yield strength and ultimate tensile strength were improved clearly after heat treatment at 200 °C for 10 h compared with that at the extrusion state, which can be mainly contributed to the precipitation strengthening. The biocorrosion behaviors of the JDBM alloy were studied using immersion tests and electrochemical tests. The results reveal that the extruded JDBM alloy and the aging treatment on the extruded alloy show much better biocorrosion resistance than that at solid solution state (T4 treatment), and the JDBM exhibited favorable uniform corrosion mode in SBF. Copyright © 2011 Elsevier Ltd. All rights reserved.

Forecasting Kp from solar wind data: input parameter study using 3-hour averages and 3-hour range values

NASA Astrophysics Data System (ADS)

Wintoft, Peter; Wik, Magnus; Matzka, Jürgen; Shprits, Yuri

2017-11-01

We have developed neural network models that predict Kp from upstream solar wind data. We study the importance of various input parameters, starting with the magnetic component Bz, particle density n, and velocity V and then adding total field B and the By component. As we also notice a seasonal and UT variation in average Kp we include functions of day-of-year and UT. Finally, as Kp is a global representation of the maximum range of geomagnetic variation over 3-hour UT intervals we conclude that sudden changes in the solar wind can have a big effect on Kp, even though it is a 3-hour value. Therefore, 3-hour solar wind averages will not always appropriately represent the solar wind condition, and we introduce 3-hour maxima and minima values to some degree address this problem. We find that introducing total field B and 3-hour maxima and minima, derived from 1-minute solar wind data, have a great influence on the performance. Due to the low number of samples for high Kp values there can be considerable variation in predicted Kp for different networks with similar validation errors. We address this issue by using an ensemble of networks from which we use the median predicted Kp. The models (ensemble of networks) provide prediction lead times in the range 20-90 min given by the time it takes a solar wind structure to travel from L1 to Earth. Two models are implemented that can be run with real time data: (1) IRF-Kp-2017-h3 uses the 3-hour averages of the solar wind data and (2) IRF-Kp-2017 uses in addition to the averages, also the minima and maxima values. The IRF-Kp-2017 model has RMS error of 0.55 and linear correlation of 0.92 based on an independent test set with final Kp covering 2 years using ACE Level 2 data. The IRF-Kp-2017-h3 model has RMSE = 0.63 and correlation = 0.89. We also explore the errors when tested on another two-year period with real-time ACE data which gives RMSE = 0.59 for IRF-Kp-2017 and RMSE = 0.73 for IRF-Kp-2017-h3. The errors as function of Kp and for different years are also studied.

75 FR 22892 - Environmental Impact Statement: Salt Lake County, UT

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-30

... Lake County, UT AGENCY: Federal Highway Administration (FHWA), USDOT. ACTION: Notice of Intent. SUMMARY... be prepared for a proposed transportation improvement project in Salt Lake County, Utah. FOR FURTHER... 4700 South, Suite 9A, Salt Lake City, UT 84118, telephone (801) 963-0182, e-mail [email protected

75 FR 9476 - Environmental Impact Statement: Salt Lake County, UT

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-02

... Lake County, UT AGENCY: Federal Highway Administration (FHWA), DOT. ACTION: Notice of intent. SUMMARY... be prepared for a proposed transportation improvement project in Salt Lake County, Utah. FOR FURTHER... 9A, Salt Lake City, UT 84118, Telephone: (801) 963-0182, E-mail: [email protected] . The Utah...

A Study of the Broadband Parametric Acoustic Array

DTIC Science & Technology

1982-01-04

iJ~ exp[~~) fj 2 0 . (3.8) This expression indicates a maximum when f =--n (3.9) This result was derived by Findeisen . 64 Using the definitions of n...Interactions of Progressive Finite Amplitude Waves in Nondispersive Fluids," J. Acoust. Soc. Am. 50, 1299-1312 (1971). 64. A. G. Findeisen and S. A. Means, "A...Clynch, ARL:UT 126 George P. Coble, ARL:UT 127 Bernie R. Criswell, ARL:IJT 128 Charles R. Culbertson, ARL:UT 129 Allen G. Findeisen , ARL:UT 130 Karl C

Symmetry Reductions of Fourth-Order Nonlinear Diffusion Equations: Lubrication Model and Some Generalizations

NASA Astrophysics Data System (ADS)

Gandarias, M. L.; Medina, E.

Fourth-order nonlinear diffusion equations appear frequently in the description of physical processes, among these, the lubrication equation ut = (unuxxxx)x or the corresponding modified version ut = unuxxxx play an important role in the study of the interface movements. In this work we analyze the generalizations of the above equations given by ut = (f(u)uxxxx)x, ut = (f(u)uxxxx, and we find that if f(u) = un or f(u) = e-u the equations admit extra classical symmetries. The corresponding reductions are performed and some solutions are characterized.

Neural reactivation links unconscious thought to decision-making performance.

PubMed

Creswell, John David; Bursley, James K; Satpute, Ajay B

2013-12-01

Brief periods of unconscious thought (UT) have been shown to improve decision making compared with making an immediate decision (ID). We reveal a neural mechanism for UT in decision making using blood oxygen level-dependent (BOLD) functional magnetic resonance imaging. Participants (N = 33) encoded information on a set of consumer products (e.g. 48 attributes describing four different cars), and we manipulated whether participants (i) consciously thought about this information (conscious thought), (ii) completed a difficult 2-back working memory task (UT) or (iii) made an immediate decision about the consumer products (ID) in a within-subjects blocked design. To differentiate UT neural activity from 2-back working memory neural activity, participants completed an independent 2-back task and this neural activity was subtracted from neural activity occurring during the UT 2-back task. Consistent with a neural reactivation account, we found that the same regions activated during the encoding of complex decision information (right dorsolateral prefrontal cortex and left intermediate visual cortex) continued to be activated during a subsequent 2-min UT period. Moreover, neural reactivation in these regions was predictive of subsequent behavioral decision-making performance after the UT period. These results provide initial evidence for post-encoding unconscious neural reactivation in facilitating decision making.

Usability Tests in Medicine: A Cost-Benefit Analysis for Hospitals Before Acquiring Medical Devices for Theatre.

PubMed

Gonser, Phillipp; Fuchsberger, Thomas; Matern, Ulrich

2017-08-01

The use of active medical devices in clinical routine should be as safe and efficient as possible. Usability tests (UTs) help improve these aspects of medical devices during their development, but UTs can be of use for hospitals even after a product has been launched. The present pilot study examines the costs and possible benefits of UT for hospitals before buying new medical devices for theatre. Two active medical devices with different complexity were tested in a standardized UT and a cost-benefit analysis was carried out assuming a different device bought at the same price with a higher usability could increase the efficiency of task solving and due to that save valuable theatre time. The cost of the UT amounted up to €19.400. Hospitals could benefit from UTs before buying new devices for theatre by reducing time-consuming operator errors and thereby increase productivity and patient safety. The possible benefits amounted from €23.300 to €1.570.000 (median = €797.000). Not only hospitals could benefit economically from investing in a UT before deciding to buy a medical device, but especially patients would profit from a higher usability by reducing possible operator errors and increase safety and performance of use.

Neural reactivation links unconscious thought to decision-making performance

PubMed Central

Bursley, James K.; Satpute, Ajay B.

2013-01-01

Brief periods of unconscious thought (UT) have been shown to improve decision making compared with making an immediate decision (ID). We reveal a neural mechanism for UT in decision making using blood oxygen level-dependent (BOLD) functional magnetic resonance imaging. Participants (N = 33) encoded information on a set of consumer products (e.g. 48 attributes describing four different cars), and we manipulated whether participants (i) consciously thought about this information (conscious thought), (ii) completed a difficult 2-back working memory task (UT) or (iii) made an immediate decision about the consumer products (ID) in a within-subjects blocked design. To differentiate UT neural activity from 2-back working memory neural activity, participants completed an independent 2-back task and this neural activity was subtracted from neural activity occurring during the UT 2-back task. Consistent with a neural reactivation account, we found that the same regions activated during the encoding of complex decision information (right dorsolateral prefrontal cortex and left intermediate visual cortex) continued to be activated during a subsequent 2-min UT period. Moreover, neural reactivation in these regions was predictive of subsequent behavioral decision-making performance after the UT period. These results provide initial evidence for post-encoding unconscious neural reactivation in facilitating decision making. PMID:23314012

Issue des accouchements sur utérus cicatriciel dans un hôpital universitaire au Burkina

PubMed Central

Dembélé, Adama; Tarnagda, Zekiba; Ouédraogo, Jean Louis; Thiombiano, Oumarou; Bambara, Moussa

2012-01-01

Certains auteurs ont tendance à privilégier la césarienne comme méthode de prise en charge d'une parturiente porteuse d'un utérus cicatriciel. D'autres auteurs préconisent un accouchement par voie basse quand des paramètres cliniques précis sont observés. Le but de cette étude est d'analyser la prise en charge et l'issue des accouchements sur utérus cicatriciel au Centre Hospitalier Universitaire Souro Sanou de Bobo-Dioulasso et de la comparer aux différentes approches recommandées. Nous avons menés une étude transversale dans le Département de Gynécologie d'Obstétrique et de Médecine de la Reproduction du Centre Hospitalier Universitaire Sanou Souro de Bobo Dioulasso du 1er août 2006 au 1er août 2007 et a concerné 252 parturientes ayant un utérus cicatriciel parmi 4256 accouchements déroulés pendant la même période. Les accouchements sur utérus cicatriciels ont représenté 5,92 % de l'ensemble des accouchements dans notre département. La moyenne d'âge des patientes était de 26,2 ans et la parité moyenne de 4,3. Une césarienne d'emblée a été pratiquée chez 44% des parturientes ayant un utérus cicatriciel et 56 % parmi elles ont fait l'objet d'une épreuve utérine. Sur l'ensemble des épreuves utérines, 61% des parturientes ont accouché par voie basse. La mortalité maternelle était nulle et La mortalité périnatale était relativement importante. Les conditions d'acceptabilité de la voie basse ont été les mêmes chez toutes les patientes et un check liste a été proposé pour une meilleure prise en charge. L'épreuve utérine en salle d'accouchement doit être la règle à chaque fois que cela est possible chez une parturiente porteuse d'utérus cicatriciel. L’établissement d'un check liste pour accouchement par voie basse sur utérus cicatriciel facilite les prises de décision. PMID:23133695

Accouchements sur utérus cicatriciel en République Démocratique du Congo: épreuve utérine et facteurs déterminants de l’issue

PubMed Central

Momat, Félix Kitenge wa; Zalagile, Pierre Akilimali; Mukalenge, Faustin Chenge; Luboya, Oscar Numbi; Kalala, Cléophas Tshibangu; Mashinda, Désiré; Grangé, Gilles; Mukuku, Olivier; Kaj, Fanny Malonga; Lubamba, Chamy Cham; Bwama, Joseph Bagambe; Mukoko, Célestin Kayembe; Kakoma, Jean Baptiste; Kalungwe, Justin Kizonde

2017-01-01

Introduction L'objectif était d'identifier les principaux facteurs de risque associés à un échec d'épreuve utérine et définir un score prédictif d'accouchement sur utérus cicatriciel en République Démocratique du Congo. Méthodes Étude multicentrique, transversale et analytique des patientes porteuses d'un utérus cicatriciel sur la période du 1er janvier au 31 décembre 2013 dans quatre maternités de la République Démocratique du Congo (RDC). Un modèle de régression logistique a été construit pour identifier les facteurs associés à l'échec de l'épreuve utérine. De ce modèle, un score prédictif a été construit pour prédire l'échec de l'épreuve utérine dans les maternités de la RDC. La courbe ROC a été utilisée pour évaluer la capacité du score construit à identifier les patientes à risque de connaitre un échec de l'épreuve utérine. Le cut off point du score prédictif a été déterminé en fonction de la sensibilité et spécificité optimale via l'index de Youden. Tous les tests ont été réalisés au seuil de signification α=0,05. Résultats Deux types de facteurs explicatifs de l'échec de l'épreuve utérine ont été retenus. Il s'agit d'un facteur sociodémographique (âge maternel) et de trois facteurs obstétricaux (hauteur utérine, présentation du fœtus et rupture prématurée des membranes). Le score de prédiction a été défini pour prédire l'échec de l'épreuve utérine. La construction de ce score s'est basée sur quatre éléments : l'âge maternel, l'état de la poche des eaux à l'admission, la hauteur utérine et la présentation fœtale. Le score minimal est de 4 et le score maximal est de 16. Le seuil est de 7. Un Score total supérieur ou égal à 7 traduit un risque d'échec de l'épreuve utérine. Conclusion L'utilisation de ce score prédictif chez les patientes pourra améliorer la qualité dans les indications de la voie haute, l'augmentation des taux de césariennes prophylactiques ainsi que la meilleure sélection des patientes soumises à l'épreuve utérine. Ceci pourra également contribuer à la réduction de la morbi-mortalité fœto-maternelle liée à la gestion de l'accouchement sur utérus cicatriciels. PMID:28819492

Evaluation of uterine artery recanalization and doppler parameters after bilateral uterine artery ligation in women with postpartum hemorrhage

PubMed Central

Kaplanoglu, Mustafa; Karateke, Atilla; Un, Burak; Gunsoy, Levend; Baloglu, Ali

2015-01-01

Aim: The evaluation of the uterine artery recanalization rate and color Doppler parameters during follow-up after bilateral uterine artery ligation (BUAL) for postpartum hemorrhage (PPH) related to uterine atony. Material and method: A total of 40 female patients who underwent BUAL for PPH related to uterine atony and 96 females who gave birth without complication at Hatay Obstetrics and Gynecology Hospital between January 2009 and December 2012 (48 months) were included in the study. The patients’ uterine artery recanalization rate and all subjects’ color Doppler ultrasonographic parameters (PI, RI, PSV and EDV) were evaluated at the 6th and 12th months. Result: No statistically significant difference was found between the age, obstetric history (gravida and parity), BMI, type of delivery, birth weight and gestational age when the demographic data of the groups were evaluated. The patient group UtA recanalization rate was 32.5% and 37.5% for the left and right UtA respectively at the 12-month follow-up. No statistically significant difference was found in the comparison of 6- and 12-month right and left uterine artery diameters and color doppler parameters of the patient group (UtA diameters P=0.322 and P=0.787, RI index P=0.390 and P=0.094, PI index P=0.949 and P=0.374, PSV P=0.335 and P=0.085, EDV P=0.173 and P=0.418, respectively). However, right and left ovarian volume was found to significantly increase during follow-up in patient group (P<0.001 for both right and left ovary). On the other hand, a statistically significant difference was found between the patient group and the control group in the comparison of the 6- and 12-month right and left uterine artery values (6th month; P<0.001 for both UtA diameters, RI, PI, PSV, EDV; 12th month; P<0.001 for right UtA diameter, RI, PI, PSV, EDV and P=0.002 for left UtA diameter). A statistically significant difference was found only in right ovary volume in the 6th month evaluation of the patient and control group ovary volumes (P=0.011). Discussion: The recanalization rate and isolated uterine blood supply during low-term follow-up are low following the BUAL technique. The evaluation of future fertility results will be helpful in determining the reliability of this procedure in a definite manner. PMID:26221335

Quantify work load and muscle functional activation patterns in neck-shoulder muscles of female sewing machine operators using surface electromyogram.

PubMed

Zhang, Fei-Ruo; He, Li-Hua; Wu, Shan-Shan; Li, Jing-Yun; Ye, Kang-Pin; Wang, Sheng

2011-11-01

Work-related musculoskeletal disorders (WMSDs) have high prevalence in sewing machine operators employed in the garment industry. Long work duration, sustained low level work and precise hand work are the main risk factors of neck-shoulder disorders for sewing machine operators. Surface electromyogram (sEMG) offers a valuable tool to determine muscle activity (internal exposure) and quantify muscular load (external exposure). During sustained and/or repetitive muscle contractions, typical changes of muscle fatigue in sEMG, as an increase in amplitude or a decrease as a shift in spectrum towards lower frequencies, can be observed. In this paper, we measured and quantified the muscle load and muscular activity patterns of neck-shoulder muscles in female sewing machine operators during sustained sewing machine operating tasks using sEMG. A total of 18 healthy women sewing machine operators volunteered to participate in this study. Before their daily sewing machine operating task, we measured the maximal voluntary contractions (MVC) and 20%MVC of bilateral cervical erector spinae (CES) and upper trapezius (UT) respectively, then the sEMG signals of bilateral UT and CES were monitored and recorded continuously during 200 minutes of sustained sewing machine operating simultaneously which equals to 20 time windows with 10 minutes as one time window. After 200 minutes' work, we retest 20%MVC of four neck-shoulder muscles and recorded the sEMG signals. Linear analysis, including amplitude probability distribution frequency (APDF), amplitude analysis parameters such as roof mean square (RMS) and spectrum analysis parameter as median frequency (MF), were used to calculate and indicate muscle load and muscular activity of bilateral CES and UT. During 200 minutes of sewing machine operating, the median load for the left cervical erector spinae (LCES), right cervical erector spinae (RCES), left upper trapezius (LUT) and right upper trapezius (RUT) were 6.78%MVE, 6.94%MVE, 6.47%MVE and 5.68%MVE, respectively. Work load of right muscles are significantly higher than that of the left muscles (P < 0.05); sEMG signal analysis of isometric contractions indicated that the amplitude value before operating was significantly higher than that of after work (P < 0.01), and the spectrum value of bilateral CES and UT were significantly lower than those of after work (P < 0.01); according to the sEMG signal data of 20 time windows, with operating time pass by, the muscle activity patterns of bilateral CES and UT showed dynamic changes, the maximal amplitude of LCES, RCES, LUT occurred at the 20th time window, RUT at 16th time window, spectrum analysis showed that the lower value happened at 7th, 16th, 20th time windows. Female sewing machine operators were exposed to high sustained static load on bilateral neck-shoulder muscles; left neck and shoulder muscles were held in more static positions; the 7th, 16th, and 20th time windows were muscle fatigue period that ergonomics intervention can protocol at these periods.

Forecasting irregular variations of UT1-UTC and LOD data caused by ENSO

NASA Astrophysics Data System (ADS)

Niedzielski, T.; Kosek, W.

2008-04-01

The research focuses on prediction of LOD and UT1-UTC time series up to one-year in the future with the particular emphasis on the prediction improvement during El Nĩ o or La Nĩ a n n events. The polynomial-harmonic least-squares model is applied to fit the deterministic function to LOD data. The stochastic residuals computed as the difference between LOD data and the polynomial- harmonic model reveal the extreme values driven by El Nĩ o or La Nĩ a. These peaks are modeled by the n n stochastic bivariate autoregressive prediction. This approach focuses on the auto- and cross-correlations between LOD and the axial component of the atmospheric angular momentum. This technique allows one to derive more accurate predictions than purely univariate forecasts, particularly during El Nĩ o/La n Nĩ a events. n

Impact behavior of basalt/epoxy composite: Comparison between flat and twill fabric

NASA Astrophysics Data System (ADS)

Papa, I.; Ricciardi, M. R.; Antonucci, V.; Langella, A.; Lopresto, V.

2018-05-01

Two types of basalt fibre reinforced epoxy laminates were realized by overlapping flat and twill woven basalt fabrics by resin infusion. Rectangular specimens, cut from the panels were impacted at penetration and at increasing energy values, to investigate the damage onset and propagation. A non-destructive technique, Ultrasound testing (UT), was adopted to investigate the internal damage. Despite the difficulties to obtain information by UT method due to the high amount of signal absorbed, the technique, properly calibrated, proved to be very useful in providing information about the presence, the shape and the extent of the delaminations. The results were compared at the aim to investigate the effect of the fiber architecture (textile). The experimental results indicate a similar impact behavior between basalt flat and twill composites but in the case of the twill a minor delaminated area was detected, even if a higher absorbed energy was recorded

New Generation VLBI: Intraday UT1 Estimations

NASA Astrophysics Data System (ADS)

Ipatov, Alexander; Ivanov, Dmitriy; Ilin, Gennadiy; Smolentsev, Sergei; Gayazov, Iskander; Mardyshkin, Vyacheslav; Fedotov, Leonid; Stempkovski, Victor; Vytnov, Alexander; Salnikov, Alexander; Surkis, Igor; Mikhailov, Andrey; Marshalov, Dmitriy; Bezrukov, Ilya; Melnikov, Alexey; Ken, Voytsekh; Kurdubov, Sergei

2016-12-01

IAA finished work on the creation of the new generation radio interferometer with two VGOS antennas co-located at Badary and Zelenchukskaya. 48 single baseline one-hour VLBI sessions (up to four sessions per day) were performed from 04 Nov to 18 Nov 2015. Observations were carried out using wideband S/X receivers, three X-band and one S-band 512 MHz channels at one or two circular polarizations. Sessions consisted of about 60 scans with a 22-second minimum scan duration. The stations' broadband acquisition systems generated 1.5-3 TB data per session, which were transferred via Internet to the IAA FX correlator. The accuracy of the group delay in a single channel was 10-20 ps, which allows the use of every single channel's observations for geodetic analysis without synthesis. 156 single channel NGS-cards were obtained in total. The RMS of the differences between UT1-UTC estimates and IERS finals values is 19 μs.

Nanocomposite scaffold with enhanced stability by hydrogen bonds between collagen, polyvinyl pyrrolidone and titanium dioxide.

PubMed

Li, Na; Fan, Xialian; Tang, Keyong; Zheng, Xuejing; Liu, Jie; Wang, Baoshi

2016-04-01

In this study, three-dimensional (3D) nanocomposite scaffolds, as potential substrates for skin tissue engineering, were fabricated by freeze drying the mixture of type I collagen extracted from porcine skin and polyvinyl pyrrolidone (PVP)-coated titanium dioxide (TiO2) nanoparticles. This procedure was performed without any cross-linker or toxic reagents to generate porosity in the scaffold. Both morphology and thermal stability of the nanocomposite scaffold were examined. The swelling behavior, mechanical properties and hydrolytic degradation of the composite scaffolds were carefully investigated. Our results revealed that collagen, PVP and TiO2 are bonded together by four main hydrogen bonds, which is an essential action for the formation of nanocomposite scaffold. Using Coasts-Redfern model, we were able to calculate the thermal degradation apparent activation energy and demonstrated that the thermal stability of nanocomposites is dependent on amount of PVP incorporated. Furthermore, SEM images showed that the collagen fibers are wrapped and stabilized on scaffolds by PVP molecules, which improve the ultimate tensile strength (UTS). The UTS of PVP-contained scaffold is four times higher than that of scaffold without PVP, whereas ultimate percentage of elongation (UPE) is decreased, and PVP can enhance the degradation resistance. Copyright © 2015 Elsevier B.V. All rights reserved.

Cluster Observations of Ion Dispersions near the Exterior Cusp

NASA Astrophysics Data System (ADS)

Escoubet, C.; Grison, B.; Berchem, J.; Trattner, K. J.; Pitout, F.; Richard, R. L.; Taylor, M. G.; Laakso, H. E.; Masson, A.; Dunlop, M. W.; Dandouras, I. S.; Reme, H.; Fazakerley, A. N.; Daly, P. W.

2013-12-01

The cusps are the places where the Earth's magnetic field lines, connected to the inner side of the magnetopause, converge. It is therefore the place where signatures of processes occurring near the subsolar point, in the tail lobes, as well as near the dawn and dusk flanks are observed. The main process that injects solar wind plasma into the polar cusp is now generally accepted to be magnetic reconnection. Depending on the IMF direction, this process will take place equatorward (for IMF southward), poleward (for IMF northward) or on the side (for IMF azimuthal) of the cusp. We report a Cluster crossing on 5 January 2002 near the exterior cusp on the southern dusk side. The IMF was mainly azimuthal (IMF-By around -5 nT), the solar wind speed around 280 km/s and the density around 5 cm-3. The four Cluster spacecraft were still in the "magnetotail" configuration with two perfect tetrahedra of 2000 km around apogee and turning into an elongated configuration near the magnetopause. C4 was the first spacecraft to enter the cusp around 19:52:04 UT, followed by C2 at 19:52:35 UT, C1 at 19:54:24 UT and C3 at 20:13:15 UT. C4 and C1 observed two ion energy dispersions at 20:10 UT and 20:40 UT and C3 at 20:35 UT and 21:15 UT. We will investigate the origin of the injections forming the dispersions and if these can be explained by the reconnection between the interplanetary magnetic field and the Earth's magnetic field.

Ultrasonic Phased Array Assessment of the Interference Fit and Leak Path of the North Anna Unit 2 Control Rod Drive Mechanism Nozzle 63 with Destructive Validation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crawford, Susan L.; Cinson, Anthony D.; MacFarlan, Paul J.

2012-08-01

The objective of this investigation was to evaluate the efficacy of ultrasonic testing (UT) for primary water leak path assessments of reactor pressure vessel (RPV) upper head penetrations. Operating reactors have experienced leakage when stress corrosion cracking of nickel-based alloy penetrations allowed primary water into the annulus of the interference fit between the penetration and the low-alloy steel RPV head. In this investigation, UT leak path data were acquired for an Alloy 600 control rod drive mechanism nozzle penetration, referred to as Nozzle 63, which was removed from the North Anna Unit 2 reactor when the RPV head was replacedmore » in 2002. In-service inspection prior to the head replacement indicated that Nozzle 63 had a probable leakage path through the interference fit region. Nozzle 63 was examined using a phased-array UT probe with a 5.0-MHz, eight-element annular array. Immersion data were acquired from the nozzle inner diameter surface. The UT data were interpreted by comparing to responses measured on a mockup penetration with known features. Following acquisition of the UT data, Nozzle 63 was destructively examined to determine if the features identified in the UT examination, including leakage paths and crystalline boric acid deposits, could be visually confirmed. Additional measurements of boric acid deposit thickness and low-alloy steel wastage were made to assess how these factors affect the UT response. The implications of these findings for interpreting UT leak path data are described.« less

Improving Strength-Ductility Balance of High Strength Dual-Phase Steels by Addition of Vanadium

NASA Astrophysics Data System (ADS)

Gong, Yu; Hua, M.; Uusitalo, J.; DeArdo, A. J.

For galvanized or galvannealed steels to be commercially successful, they must exhibit several attributes: (i) easy and inexpensive processing in the hot mill, cold mill and on the coating line, (ii) high strength with good formability and spot weldability, and (iii) good corrosion resistance, especially after cold forming. For good corrosion resistance, the coating must have sufficient coverage, be of uniform thickness, and most importantly, the coating must survive the cold stamping or forming operation. The purpose of this paper is to present research aiming at improving the steel substrate, such that high strength can be obtained while maintaining good global formability (tensile ductility), local formability (sheared-edge ductility), and good spot weldability. It is well-known that the strength of DP steels is controlled by several factors, including the amount of martensite found in the final microstructure. Recent research has revealed that the amount of austenite formed during intercritical annealing can be strongly influenced by the annealing temperature and the pre-annealing conditions of the hot band (coiling temperature) and cold band (% cold reduction). Current experiments have explored the combination of pre-annealing conditions and four annealing practices to help define the best practice to optimize the strength-formability balance in these higher strength DP steels. The steels used in these experiments contained (i) low carbon content for good spot weldability, (ii) the hardenability additions Mo and Cr for strength, and (iii) V for grain refinement, precipitation hardening and temper resistance. When processed correctly, these steels exhibited UTS levels up to 1000MPa, total elongation to 25%, reduction in area to 45%, and Hole Expansion Ratios to 50%. The results of this program will be presented and discussed.

Impacts | Research Site Name | NREL

Science.gov Websites

laboris nisi ut aliquip ex ea commodo consequat. Width of 1746px - Height can vary Read more Success nisi ut aliquip ex ea commodo consequat. Title 2 Lorem ipsum dolor sit amet, consectetur adipiscing nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Title 3 Lorem ipsum dolor

78 FR 63380 - Amendment of Class E Airspace; St. George, UT

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-24

...-0600; Airspace Docket No. 13-ANM-18] Amendment of Class E Airspace; St. George, UT AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Final rule. SUMMARY: This action amends Class E airspace at St. George Municipal Airport, St. George, UT, by removing the operating hours established by a Notice to...

Comparison of Dawn and Dusk Precipitating Electron Energy Populations Shortly After the Initial Shock for the January 10th, 1997 Magnetic Cloud

NASA Technical Reports Server (NTRS)

Spann, J.; Germany, G.; Swift, W.; Parks, G.; Brittnacher, M.; Elsen, R.

1997-01-01

The observed precipitating electron energy between 0130 UT and 0400 UT of January 10 th, 1997, indicates that there is a more energetic precipitating electron population that appears in the auroral oval at 1800-2200 UT at 030) UT. This increase in energy occurs after the initial shock of the magnetic cloud reaches the Earth (0114 UT) and after faint but dynamic polar cap precipitation has been cleared out. The more energetic population is observed to remain rather constant in MLT through the onset of auroral activity (0330 UT) and to the end of the Polar spacecraft apogee pass. Data from the Ultraviolet Imager LBH long and LBH short images are used to quantify the average energy of the precipitating auroral electrons. The Wind spacecraft located about 100 RE upstream monitored the IMF and plasma parameters during the passing of the cloud. The affects of oblique angle viewing are included in the analysis. Suggestions as to the source of this hot electron population will be presented.

Cross-Modal Approach for Karaoke Artifacts Correction

NASA Astrophysics Data System (ADS)

Yan, Wei-Qi; Kankanhalli, Mohan S.

In this chapter, we combine adaptive sampling in conjunction with video analogies (VA) to correct the audio stream in the karaoke environment κ= {κ (t) : κ (t) = (U(t), K(t)), t in ({t}s, {t}e)} where t s and t e are start time and end time respectively, U(t) is the user multimedia data. We employ multiple streams from the karaoke data K(t) = ({K}_{V }(t), {K}M(t), {K}S(t)), where K V (t), K M (t) and K S (t) are the video, musical accompaniment and original singer's rendition respectively along with the user multimedia data U(t) = ({U}A(t),{U}_{V }(t)) where U V (t) is the user video captured with a camera and U A (t) is the user's rendition of the song. We analyze the audio and video streaming features Ψ (κ ) = {Ψ (U(t), K(t))} = {Ψ (U(t)), Ψ (K(t))} = {{Ψ }U(t), {Ψ }K(t)}, to produce the corrected singing, namely output U '(t), which is made as close as possible to the original singer's rendition. Note that Ψ represents any kind of feature processing.

Cross-Modal Approach for Karaoke Artifacts Correction

NASA Astrophysics Data System (ADS)

Yan, Wei-Qi; Kankanhalli, Mohan S.

In this chapter, we combine adaptive sampling in conjunction with video analogies (VA) to correct the audio stream in the karaoke environment kappa= {kappa (t) : kappa (t) = (U(t), K(t)), t in ({t}s, {t}e)} where t s and t e are start time and end time respectively, U(t) is the user multimedia data. We employ multiple streams from the karaoke data K(t) = ({K}_{V }(t), {K}M(t), {K}S(t)), where K V (t), K M (t) and K S (t) are the video, musical accompaniment and original singer's rendition respectively along with the user multimedia data U(t) = ({U}A(t),{U}_{V }(t)) where U V (t) is the user video captured with a camera and U A (t) is the user's rendition of the song. We analyze the audio and video streaming features Ψ (kappa ) = {Ψ (U(t), K(t))} = {Ψ (U(t)), Ψ (K(t))} = {{Ψ }U(t), {Ψ }K(t)}, to produce the corrected singing, namely output U ' (t), which is made as close as possible to the original singer's rendition. Note that Ψ represents any kind of feature processing.

Cerebro-renal interactions: impact of uremic toxins on cognitive function.

PubMed

Watanabe, Kimio; Watanabe, Tsuyoshi; Nakayama, Masaaki

2014-09-01

Cognitive impairment (CI) associated with chronic kidney disease (CKD) has received attention as an important problem in recent years. Causes of CI with CKD are multifactorial, and include cerebrovascular disease, renal anemia, secondary hyperparathyroidism, dialysis disequilibrium, and uremic toxins (UTs). Among these causes, little is known about the role of UTs. We therefore selected 21 uremic compounds, and summarized reports of cerebro-renal interactions associated with UTs. Among the compounds, uric acid, indoxyl sulfate, p-cresyl sulfate, interleukin 1-β, interleukin 6, TNF-α, and PTH were most likely to affect the cerebro-renal interaction dysfunction; however, sufficient data have not been obtained for other UTs. Notably, most of the data were not obtained under uremic conditions; therefore, the impact and mechanism of each UT on cognition and central nervous system in uremic state remains unknown. At present, impacts and mechanisms of UT effects on cognition are poorly understood. Clarifying the mechanisms and establishing novel therapeutic strategies for cerebro-renal interaction dysfunction is expected to be subject of future research. Copyright © 2014 Elsevier Inc. All rights reserved.

Stabilization in a two-species chemotaxis system with a logistic source

NASA Astrophysics Data System (ADS)

Tello, J. I.; Winkler, M.

2012-05-01

We study a system of three partial differential equations modelling the spatio-temporal behaviour of two competitive populations of biological species both of which are attracted chemotactically by the same signal substance. More precisely, we consider the initial-boundary value problem for \\[ \\begin{equation*} \\fl\\left\\{ \\begin{array}{@{}l} u_t= d_1\\Delta u - \\chi_1 \

Developing precipitation hardenable high entropy alloys

NASA Astrophysics Data System (ADS)

Gwalani, Bharat

High entropy alloys (HEAs) is a concept wherein alloys are constructed with five or more elements mixed in equal proportions; these are also known as multi-principle elements (MPEs) or complex concentrated alloys (CCAs). This PhD thesis dissertation presents research conducted to develop precipitation-hardenable high entropy alloys using a much-studied fcc-based equi-atomic quaternary alloy (CoCrFeNi). Minor additions of aluminium make the alloy amenable for precipitating ordered intermetallic phases in an fcc matrix. Aluminum also affects grain growth kinetics and Hall-Petch hardenability. The use of a combinatorial approach for assessing composition-microstructure-property relationships in high entropy alloys, or more broadly in complex concentrated alloys; using laser deposited compositionally graded AlxCrCuFeNi 2 (0 < x < 1.5) complex concentrated alloys as a candidate system. The composition gradient has been achieved from CrCuFeNi2 to Al 1.5CrCuFeNi2 over a length of ˜25 mm, deposited using the laser engineered net shaping process from a blend of elemental powders. With increasing Al content, there was a gradual change from an fcc-based microstructure (including the ordered L12 phase) to a bcc-based microstructure (including the ordered B2 phase), accompanied with a progressive increase in microhardness. Based on this combinatorial assessment, two promising fcc-based precipitation strengthened systems have been identified; Al0.3CuCrFeNi2 and Al0.3CoCrFeNi, and both compositions were subsequently thermo-mechanically processed via conventional techniques. The phase stability and mechanical properties of these alloys have been investigated and will be presented. Additionally, the activation energy for grain growth as a function of Al content in these complex alloys has also been investigated. Change in fcc grain growth kinetic was studied as a function of aluminum; the apparent activation energy for grain growth increases by about three times going from Al0.1CoCrFeNi (3% Al (at%)) to Al0.3CoCrFeNi. (7% Al (at%)). Furthermore, Al addition leads to the precipitation of highly refined ordered L12 (gamma') and B2 precipitates in Al0.3CoCrFeNi. A detailed investigation of precipitation of the ordered phases in Al0.3CoCrFeNi and their thermal stability is done using atom probe tomography (APT), transmission electron microscopy (TEM) and Synchrotron X-ray in situ and ex situ analyses. The alloy strengthened via grain boundary strengthening following the Hall-Petch relationship offers a large increment of strength with small variation in grain size. Tensile strength of the Al0.3CoFeNi is increased by 50% on precipitation fine-scale gamma' precipitates. Furthermore, precipitation of bcc based ordered phase B2 in Al0.3CoCrFeNi can further strengthen the alloy. Fine-tuning the microstructure by thermo-mechanical treatments achieved a wide range of mechanical properties in the same alloy. The Al0.3CoCrFeNi HEA exhibited ultimate tensile strength (UTS) of ˜250 MPa and ductility of ˜65%; a UTS of ˜1100 MPa and ductility of ˜30%; and a UTS of 1850 MPa and a ductility of 5% after various thermo-mechanical treatments. Grain sizes, precipitates type and size scales manipulated in the alloy result in different strength ductility combinations. Henceforth, the alloy presents a fertile ground for development by grain boundary strengthening and precipitation strengthening, and offers very high activation energy of grain growth aptly suitable for high-temperature applications.

Movement of NH3 through the human urea transporter B: a new gas channel

PubMed Central

Musa-Aziz, Raif; Enkavi, Giray; Mahinthichaichan, P.; Tajkhorshid, Emad; Boron, Walter F.

2013-01-01

Aquaporins and Rh proteins can function as gas (CO2 and NH3) channels. The present study explores the urea, H2O, CO2, and NH3 permeability of the human urea transporter B (UT-B) (SLC14A1), expressed in Xenopus oocytes. We monitored urea uptake using [14C]urea and measured osmotic water permeability (Pf) using video microscopy. To obtain a semiquantitative measure of gas permeability, we used microelectrodes to record the maximum transient change in surface pH (ΔpHS) caused by exposing oocytes to 5% CO2/33 mM HCO3− (pHS increase) or 0.5 mM NH3/NH4+ (pHS decrease). UT-B expression increased oocyte permeability to urea by >20-fold, and Pf by 8-fold vs. H2O-injected control oocytes. UT-B expression had no effect on the CO2-induced ΔpHS but doubled the NH3-induced ΔpHS. Phloretin reduced UT-B-dependent urea uptake (Jurea*) by 45%, Pf* by 50%, and (−ΔpHS*)NH3 by 70%. p-Chloromercuribenzene sulfonate reduced Jurea* by 25%, Pf* by 30%, and (ΔpHS*)NH3 by 100%. Molecular dynamics (MD) simulations of membrane-embedded models of UT-B identified the monomeric UT-B pores as the main conduction pathway for both H2O and NH3 and characterized the energetics associated with permeation of these species through the channel. Mutating each of two conserved threonines lining the monomeric urea pores reduced H2O and NH3 permeability. Our data confirm that UT-B has significant H2O permeability and for the first time demonstrate significant NH3 permeability. Thus the UTs become the third family of gas channels. Inhibitor and mutagenesis studies and results of MD simulations suggest that NH3 and H2O pass through the three monomeric urea channels in UT-B. PMID:23552862

Tolerance of uncertainty: Conceptual analysis, integrative model, and implications for healthcare.

PubMed

Hillen, Marij A; Gutheil, Caitlin M; Strout, Tania D; Smets, Ellen M A; Han, Paul K J

2017-05-01

Uncertainty tolerance (UT) is an important, well-studied phenomenon in health care and many other important domains of life, yet its conceptualization and measurement by researchers in various disciplines have varied substantially and its essential nature remains unclear. The objectives of this study were to: 1) analyze the meaning and logical coherence of UT as conceptualized by developers of UT measures, and 2) develop an integrative conceptual model to guide future empirical research regarding the nature, causes, and effects of UT. A narrative review and conceptual analysis of 18 existing measures of Uncertainty and Ambiguity Tolerance was conducted, focusing on how measure developers in various fields have defined both the "uncertainty" and "tolerance" components of UT-both explicitly through their writings and implicitly through the items constituting their measures. Both explicit and implicit conceptual definitions of uncertainty and tolerance vary substantially and are often poorly and inconsistently specified. A logically coherent, unified understanding or theoretical model of UT is lacking. To address these gaps, we propose a new integrative definition and multidimensional conceptual model that construes UT as the set of negative and positive psychological responses-cognitive, emotional, and behavioral-provoked by the conscious awareness of ignorance about particular aspects of the world. This model synthesizes insights from various disciplines and provides an organizing framework for future research. We discuss how this model can facilitate further empirical and theoretical research to better measure and understand the nature, determinants, and outcomes of UT in health care and other domains of life. Uncertainty tolerance is an important and complex phenomenon requiring more precise and consistent definition. An integrative definition and conceptual model, intended as a tentative and flexible point of departure for future research, adds needed breadth, specificity, and precision to efforts to conceptualize and measure UT. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Impact of aspirin on trophoblastic invasion in women with abnormal uterine artery Doppler at 11-14 weeks: a randomized controlled study.

PubMed

Scazzocchio, E; Oros, D; Diaz, D; Ramirez, J C; Ricart, M; Meler, E; González de Agüero, R; Gratacos, E; Figueras, F

2017-04-01

Defective trophoblastic invasion is a key feature in many cases of pre-eclampsia (PE). Uterine artery (UtA) Doppler is a validated non-invasive proxy for trophoblastic invasion. The aim of this study was to explore whether low-dose aspirin, administered from the first trimester, improves trophoblastic invasion, evaluated by UtA Doppler during the second and third trimesters in women defined as high risk by abnormal first-trimester UtA Doppler. This randomized Phase-II study had a triple-blind, parallel-arm, controlled design. Singleton pregnancies with abnormal mean UtA Doppler at 11-14 weeks and absence of other major risk factors for PE received 150 mg extended-release aspirin or identical-appearing placebo tablets from study inclusion to 28 weeks. Main outcome measure was UtA pulsatility index (PI) at 28 weeks' gestation. Secondary outcomes included frequency of development of PE and growth restriction/small-for-gestational age (SGA). A total of 155 women completed the follow-up and were analyzed. No difference in mean UtA-PI was found between women in the aspirin and placebo groups at 28 weeks (mean UtA-PI Z-score (mean ± SD), 0.99 ± 1.48 vs 0.85 ± 1.25; P = 0.52). Seven women developed PE: four (5%) in the aspirin group and three (4%) in the placebo group. There was a trend toward lower incidence of SGA in the aspirin group (8.8% vs 17.3%; P = 0.11). In women with defective trophoblastic invasion, as reflected by abnormal UtA Doppler, low-dose aspirin started in the first trimester does not have a significant effect on UtA impedance as pregnancy progresses; however, the study was underpowered to detect potential small effects . Copyright © 2016 ISUOG. Published by John Wiley & Sons Ltd. Copyright © 2016 ISUOG. Published by John Wiley & Sons Ltd.

Broad band energy spectrum and a low frequency QPO from H1743-322 in the hard state revealed by INTEGRAL and Swift observations

NASA Astrophysics Data System (ADS)

Rodriguez, J.; Cadolle Bel, M.; Tomsick, J. A.; Hannikainen, D.; Pottschmidt, K.; Kuulkers, E.; Corbel, S.; Coriat, M.; Goldwurm, A.; Russell, D. M.; Wilms, J.

2011-04-01

Following the report of renewed activity of the microquasar H1743-322 (aka IGR J17464-3213, ATels #3263, #3267) we have triggered a Swift ToO. The observation was performed on April 10, 2011 between 7.9h UT and 16.12h UT, therefore in quasi-simultaneity with the INTEGRAL bulge monitoring program (April 10, 2011 18.0h UT to 21.7h UT). The Swift/XRT was operated in Window Timing mode.

An extract of Urtica dioica L. mitigates obesity induced insulin resistance in mice skeletal muscle via protein phosphatase 2A (PP2A).

PubMed

Obanda, Diana N; Ribnicky, David; Yu, Yongmei; Stephens, Jacqueline; Cefalu, William T

2016-02-26

The leaf extract of Urtica dioica L. (UT) has been reported to improve glucose homeostasis in vivo, but definitive studies on efficacy and mechanism of action are lacking. We investigated the effects of UT on obesity- induced insulin resistance in skeletal muscle. Male C57BL/6J mice were divided into three groups: low-fat diet (LFD), high-fat diet (HFD) and HFD supplemented with UT. Body weight, body composition, plasma glucose and plasma insulin were monitored. Skeletal muscle (gastrocnemius) was analyzed for insulin sensitivity, ceramide accumulation and the post translational modification and activity of protein phosphatase 2A (PP2A). PP2A is activated by ceramides and dephosphorylates Akt. C2C12 myotubes exposed to excess free fatty acids with or without UT were also evaluated for insulin signaling and modulation of PP2A. The HFD induced insulin resistance, increased fasting plasma glucose, enhanced ceramide accumulation and PP2A activity in skeletal muscle. Supplementation with UT improved plasma glucose homeostasis and enhanced skeletal muscle insulin sensitivity without affecting body weight and body composition. In myotubes, UT attenuated the ability of FFAs to induce insulin resistance and PP2A hyperactivity without affecting ceramide accumulation and PP2A expression. UT decreased PP2A activity through posttranslational modification that was accompanied by a reduction in Akt dephosphorylation.

Major Solar Proton Event during September 24-30, 2001 using Imaging Riometer Technique (P42)

NASA Astrophysics Data System (ADS)

Sharma, A. K.; Vhatkar, R. S.

2006-11-01

sharma_ashokkumar@yahoo.com Major outbursts of mass and energy i.e. a fast full halo CME with speed of 2402 km/sec from region 9632, located on the Sun at S16 E23 was observed at 1030 UT by SOHO/LASCO C3 coronagraph on September 24, 2001. The proton event at greater than 100 MeV began at 1440 UT on 24 September, reached a maximum of 31.2 PFU at 0755 UT on 25 September and ended at 1940 UT on 26 September 2001. The protons event at greater than 10 MeV began at 1215 UT on 24 September, reached a maximum of 12,900 PFU at 2235 UT on 25 September and ended at 1710 UT on 30 September 2001. These extremely high energetic protons accelerated during CMEs produces significant ionization in the D region of the ionosphere at high latitudes. Increase in ionization in the D region causes cosmic noise absorption. The major Polar Cap Absorption (PCA) observed during SEPTEMBER 24 -30, 2001 will be discussed in this paper. Imaging riometer observations were made from Kilpisjarvi (69.05oN; 20.79oW), Northern Finland during the PCA event. For this the remote and insitu data have been used. The imaging riometer for ionospheric studies (IRIS) is used to quantify the intensity, time of occurrence and location of CME effects on the ionosphere.

The Use of Daily Geodetic UT1 and LOD Data in the Optimal Estimation of UT1 and LOD With the JPL Kalman Earth Orientation Filter

NASA Technical Reports Server (NTRS)

Freedman, A. P.; Steppe, J. A.

1995-01-01

The Jet Propulsion Laboratory Kalman Earth Orientation Filter (KEOF) uses several of the Earth rotation data sets available to generate optimally interpolated UT1 and LOD series to support spacecraft navigation. This paper compares use of various data sets within KEOF.

75 FR 62461 - Revocation and Establishment of Class E Airspace; St. George, UT

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-12

...-0660; Airspace Docket No. 10-ANM-4] Revocation and Establishment of Class E Airspace; St. George, UT... Class E airspace at St. George, UT, as the airport will be closing, eliminating the need for controlled airspace. This action will establish Class E airspace for the new St. George Municipal Airport located to...

76 FR 28074 - Notice of Inventory Completion: Utah Museum of Natural History, Salt Lake City, UT

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-13

... Museum of Natural History, Salt Lake City, UT AGENCY: National Park Service, Interior. ACTION: Notice... of the Utah Museum of Natural History, Salt Lake City, UT. The human remains were removed from Snow... sole responsibility of the museum, institution, or Federal agency that has control of the Native...

On the Processing of Martensitic Steels in Continuous Galvanizing Lines: Part II

NASA Astrophysics Data System (ADS)

Song, Taejin; Kwak, Jaihyun; de Cooman, B. C.

2012-01-01

The conventional continuous hot-dip galvanizing (GI) and galvannealing (GA) processes can be applied to untransformed austenite to produce Zn and Zn-alloy coated low-carbon ultra-high-strength martensitic steel provided specific alloying additions are made. The most suitable austenite decomposition behavior results from the combined addition of boron, Cr, and Mo, which results in a pronounced transformation bay during isothermal transformation. The occurrence of this transformation bay implies a considerable retardation of the austenite decomposition in the temperature range below the bay, which is close to the stages in the continuous galvanizing line (CGL) thermal cycle related to the GI and GA processes. After the GI and GA processes, a small amount of granular bainite, which consists of bainitic ferrite and discrete islands of martensite/austenite (M/A) constituents embedded in martensite matrix, is present in the microstructure. The ultimate tensile strength (UTS) of the steel after the GI and GA cycle was over 1300 MPa, and the stress-strain curve was continuous without any yielding phenomena.

Effect of Multi-Pass Friction Stir Processing on Mechanical Properties for AA2024/Al2O3 Nanocomposites

PubMed Central

2017-01-01

In the present work, an aluminum metal matrix reinforced with (Al2O3) nanoparticles was fabricated as a surface composite sheet using friction stir processing (FSP). The effects of processing parameters on mechanical properties, hardness, and microstructure grain were investigated. The results revealed that multi-pass FSP causes a homogeneous distribution and good dispersion of Al2O3 in the metal matrix, and consequently an increase in the hardness of the matrix composites. A finer grain is observed in the microstructure examination in specimens subjected to second and third passes of FSP. The improvement in the grain refinement is 80% compared to base metal. The processing parameters, particularly rotational tool speed and pass number in FSP, have a major effect on strength properties and surface hardness. The ultimate tensile strength (UTS) and the average hardness are improved by 25% and 46%, respectively, due to presence of reinforcement Al2O3 nanoparticles. PMID:28885575

Effects of Zr Addition on Strengthening Mechanisms of Al-Alloyed High-Cr ODS Steels.

PubMed

Ren, Jian; Yu, Liming; Liu, Yongchang; Liu, Chenxi; Li, Huijun; Wu, Jiefeng

2018-01-12

Oxide dispersion strengthened (ODS) steels with different contents of zirconium (denoted as 16Cr ODS, 16Cr-0.3Zr ODS and 16Cr-0.6Zr ODS) were fabricated to investigate the effects of Zr on strengthening mechanism of Al-alloyed 16Cr ODS steel. Electron backscatter diffraction (EBSD) results show that the mean grain size of ODS steels could be decreased by Zr addition. Transmission electron microscope (TEM) results indicate that Zr addition could increase the number density but decrease the mean diameter and inter-particle spacing of oxide particles. Furthermore, it is also found that in addition to Y-Al-O nanoparticles, Y-Zr-O oxides with finer size were observed in 16Cr-0.3Zr ODS and 16Cr-0.6Zr ODS steels. These changes in microstructure significantly increase the yield strength (YS) and ultimate tensile strength (UTS) of ODS steels through mechanisms of grain boundary strengthening and dispersion strengthening.

Effect of Copper Coated SiC Reinforcements on Microstructure, Mechanical Properties and Wear of Aluminium Composites

NASA Astrophysics Data System (ADS)

Kori, P. S.; Vanarotti, Mohan; Angadi, B. M.; Nagathan, V. V.; Auradi, V.; Sakri, M. I.

2017-08-01

Experimental investigations are carried out to study the influence of copper coated Silicon carbide (SiC) reinforcements in Aluminum (Al) based Al-SiC composites. Wear behavior and mechanical Properties like, ultimate tensile strength (UTS) and hardness are studied in the present work. Experimental results clearly revealed that, an addition of SiC particles (5, 10 and 15 Wt %) has lead in the improvement of hardness and ultimate tensile strength. Al-SiC composites containing the Copper coated SiC reinforcements showed better improvement in mechanical properties compared to uncoated ones. Characterization of Al-SiC composites are carried out using optical photomicrography and SEM analysis. Wear tests are carried out to study the effects of composition and normal pressure using Pin-On Disc wear testing machine. Results suggested that, wear rate decreases with increasing SiC composition, further an improvement in wear resistance is observed with copper coated SiC reinforcements in the Al-SiC metal matrix composites (MMC’s).

Effects of Zr Addition on Strengthening Mechanisms of Al-Alloyed High-Cr ODS Steels

PubMed Central

Ren, Jian; Yu, Liming; Liu, Yongchang; Liu, Chenxi; Li, Huijun; Wu, Jiefeng

2018-01-01

Oxide dispersion strengthened (ODS) steels with different contents of zirconium (denoted as 16Cr ODS, 16Cr-0.3Zr ODS and 16Cr-0.6Zr ODS) were fabricated to investigate the effects of Zr on strengthening mechanism of Al-alloyed 16Cr ODS steel. Electron backscatter diffraction (EBSD) results show that the mean grain size of ODS steels could be decreased by Zr addition. Transmission electron microscope (TEM) results indicate that Zr addition could increase the number density but decrease the mean diameter and inter-particle spacing of oxide particles. Furthermore, it is also found that in addition to Y-Al-O nanoparticles, Y-Zr-O oxides with finer size were observed in 16Cr-0.3Zr ODS and 16Cr-0.6Zr ODS steels. These changes in microstructure significantly increase the yield strength (YS) and ultimate tensile strength (UTS) of ODS steels through mechanisms of grain boundary strengthening and dispersion strengthening. PMID:29329260

Polar Electrodynamics During the 14-16 July 2012 Geomagnetic Storm

NASA Astrophysics Data System (ADS)

Anderson, B. J.; Merkin, V. G.; Korth, H.; Dyrud, L. P.; Barnes, R. J.; Ruohoniemi, J. M.; Gjerloev, J. W.; Fentzke, J.

2012-12-01

We present an analysis of the Birkeland current dynamics observed by AMPERE during the CME-driven geomagnetic storm of 14-16 July, 2012, when the provisional Dst reached -125 nT from 17 to 19 UT on 15 July. The CME magnetic cloud presented a consistently southward IMF lasting over 30 hours, affording an opportunity to examine the system response under sustained, steady forcing. The shock arrived at ACE at 1725 UT on 14 July 2012 when the proton speed increased from 390 to 640 km/s by 1738 UT, while the IMF remained southward and intensified from -4 nT to between -10 and -15 nT. By 1810 UT the Birkeland currents increased in intensity by a factor of 5 to 10 and expanded equatorward to about 60N MLAT. During the sheath passage, the IMF rotated multiple times between southward, duskward, dawnard, or northward and the dayside Birkeland currents displayed considerable variability in both intensity and distribution. An impulsive enhancement in nightside currents occurred near 0150 UT on 15 July followed by a second event near 0330 UT, after which the nightside expanded equatorward to 55 MLAT. At ACE the CME sheath was observed until 0551 UT on 15 July when the IMF magnitude increased from 10 nT to 25 nT by 0554 UT and turned consistently southward, BZ = -13 to -15 nT, and anti-sunward, BX = +18 to +23 nT as the CME magnetic cloud arrived. The cloud passage lasted until 1350 UT on 16 July during which time the IMF decreased nearly linearly in time from 27 nT to 10 nT, had a consistently southward orientation, and the proton speed gradually decreased from 650 km/s to 400 km/s. The IMF BZ remained steadily below -14 nT until 0400 UT on 16 July. The first additional current intensification occurred on the dayside at 0620 UT on 15 July. During the next three hours, the currents expanded equatorward of 50N MLAT, and were generally symmetric between dawn and dusk exhibiting pertburbations exceeding 3000 nT. There were multiple, >2000 nT, nightside impulsive events indicating major substorms followed by extended periods displaying two sets of upward-downward current pairs in the evening sector, consistent with a double auroral oval structure. SuperDARN observations, and MHD simulations are used to estimate the time history of energy flux to the ionosphere, quantify the flows, and discuss the possible effects of heavy ion loading and inner magnetosphere dynamics not included in MHD simulations presented here.

Aerobic capacity in speed-power athletes aged 20-90 years vs endurance runners and untrained participants.

PubMed

Kusy, K; Zieliński, J

2014-02-01

We studied relationships between age and aerobic capacity in three groups of subjects adhering to different exercise modalities. A total of 203 men aged 20-90 years were examined: 52 speed-power track and field athletes (SP), 89 endurance runners (ER) and 62 untrained individuals (UT). Maximal exercise characteristics were obtained during a graded treadmill test until exhaustion: oxygen uptake (VO2max), heart rate (HRmax), oxygen pulse (O2 Pulsemax) and maximal distance (Distmax). Information about training history and weekly training amount was collected. A linear model of regression was adopted. VO2max in SP was lower than in ER, but significantly higher than in UT. The cross-sectional rates of decline in body mass-adjusted VO2max and Distmax were significantly smaller in SP than in ER and UT. About 80 years of age, the levels of VO2max and Distmax reached similar values in SP and ER. The decline in HRmax, but not in O2 Pulsemax was suggested as a cardiac adaptation accounting for between-group differences in VO2max loss. Weekly training volume was a significant positive predictor of age-related changes in aerobic capacity. In conclusion, not only endurance, but also speed-power exercise appears adequate to ensure an elevated aerobic capacity at old age. © 2012 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Target Housing Material Options

DOE Office of Scientific and Technical Information (OSTI.GOV)

Woloshun, Keith Albert

2016-02-11

With gas cooling, heat transfer coefficients are low compared to water. The benefit of gas from a heat transfer point of view is that there is really no upper temperature limit for the coolant, as compared to water, which is limited ultimately by the critical point, and in practice the critical heat flux. In our case with parallel flow channels, water is limited to even lower operating limits by nucleate boiling. So gas can get as hot as the containment material will allow, but to get the density and heat transfer up to something reasonable, we must also increase pressure,more » thus increasing stress on the containment, namely the front and back faces. We are designing to ASME BPVC, which, for most materials allows a maximum stress of UTS/3. So we want the highest possible UTS. For reference, the front face stress in the 12 mm target at 300 psi was about 90 MPa. The inconel 718 allowable stress at 900°C is 1/3 of 517 or 172 MPa. So we are in a very safe place, but the uTS is dropping rapidly with temperature above 900°C. As we increase target diameter, the challenge will be to keep the stress down. We are probably looking at keeping the allowable at or above the present value, and at as high a temperature as possible.« less

Very high cloud detection in more than two decades of HIRS data

NASA Astrophysics Data System (ADS)

Kolat, Utkan; Menzel, W. Paul; Olson, Erik; Frey, Richard

2013-04-01

This paper reports on the use of High-resolution Infrared Radiation Sounder (HIRS) measurements to infer the presence of upper tropospheric and lower stratospheric (UT/LS) clouds. UT/LS cloud detection is based on the fact that, when viewing an opaque UT/LS cloud that fills the sensor field of view, positive lapse rates above the tropopause cause a more absorbing CO2 or H2O-sensitive spectral band to measure a brightness temperature warmer than that of a less absorbing or nearly transparent infrared window spectral band. The HIRS sensor has flown on 16 polar-orbiting satellites from TIROS-N through NOAA-19 and Metop-A and -B, forming the only 30 year record that includes H2O and CO2-sensitive spectral bands enabling the detection of these UT/LS clouds. Comparison with collocated Cloud-Aerosol Lidar with Orthogonal Polarization data reveals that 97% of the HIRS UT/LS cloud determinations are within 2.5 km of the tropopause (defined as the coldest level in the National Centers for Environmental Prediction Global Data Assimilation System); more clouds are found above the tropopause than below. From NOAA-14 data spanning 1995 through 2005, we find indications of UT/LS clouds in 0.7% of the observations from 60N to 60S using CO2 absorption bands; however, in the region of the Inter-Tropical Convergence Zone (ITCZ), this increases to 1.7%. During El Niño years, UT/LS clouds shift eastward out of their normal location in the western Pacific region. Monthly trends from 1987 through 2011 using data from NOAA-10 onwards show decreases in UT/LS cloud detection in the region of the ITCZ from 1987 until 1996, increases until 2001, and decreases thereafter.

Distinct sources of injections in the polar cusp observed by Cluster

NASA Astrophysics Data System (ADS)

Escoubet, C. Philippe; Reme, Henri; Dunlop, Malcolm; Daly, Patrick; Laakso, Harri; Berchem, Jean; Richard, Robert; Taylor, Matthew; Trattner, Karlheinz; Grison, Benjamin; Dandouras, Iannis; Fazakerley, Andrew; Pitout, Frederic; Masson, Arnaud

The main process that injects solar wind plasma into the polar cusp is now generally accepted to be magnetic reconnection. Depending on the IMF direction, this process takes place equatorward (for IMF southward), poleward (for IMF northward) or on the dusk or dawn sides (for IMF azimuthal) of the cusp. We report a Cluster crossing on 5 January 2002 near the exterior cusp on the southern dusk side. The IMF was mainly azimuthal (IMF-By around -5 nT), the solar wind speed lower than usual around 280 km/s and the density around 5 cm-3. The four Cluster spacecraft had an elongated configuration near the magnetopause. C4 was the first spacecraft to enter the cusp around 19:52:04 UT, followed by C2 at 19:52:35 UT, C1 at 19:54:24 UT and C3 at 20:13:15 UT. C4 and C1 observed two ion energy dispersions at 20:10 UT and 20:40 UT and C3 at 20:35 UT and 21:15 UT. Using the time of flight technique on the upgoing and downgoing ions in the dispersions, we obtain an altitude of the sources of these ions between 14 and 20 RE. Using Tsyganenko model, these sources are located on the dusk flank, past the terminator. The first injection by C3 is seen at approximately the same time as the 2nd injection on C1 but their sources at the magnetopause were separated by more than 10 RE. This would imply that two distinct sources were active at the same time on the dusk flank of the magnetosphere.

Uterine artery blood flow, fetal hypoxia and fetal growth

PubMed Central

Browne, Vaughn A.; Julian, Colleen G.; Toledo-Jaldin, Lillian; Cioffi-Ragan, Darleen; Vargas, Enrique; Moore, Lorna G.

2015-01-01

Evolutionary trade-offs required for bipedalism and brain expansion influence the pregnancy rise in uterine artery (UtA) blood flow and, in turn, reproductive success. We consider the importance of UtA blood flow by reviewing its determinants and presenting data from 191 normotensive (normal, n = 125) or hypertensive (preeclampsia (PE) or gestational hypertension (GH), n = 29) Andean residents of very high (4100–4300 m) or low altitude (400 m, n = 37). Prior studies show that UtA blood flow is reduced in pregnancies with intrauterine growth restriction (IUGR) but whether the IUGR is due to resultant fetal hypoxia is unclear. We found higher UtA blood flow and Doppler indices of fetal hypoxia in normotensive women at high versus low altitude but similar fetal growth. UtA blood flow was markedly lower in early-onset PE versus normal high-altitude women, and their fetuses more hypoxic as indicated by lower fetal heart rate, Doppler indices and greater IUGR. We concluded that, despite greater fetal hypoxia, fetal growth was well defended by higher UtA blood flows in normal Andeans at high altitude but when compounded by lower UtA blood flow in early-onset PE, exaggerated fetal hypoxia caused the fetus to respond by decreasing cardiac output and redistributing blood flow to help maintain brain development at the expense of growth elsewhere. We speculate that UtA blood flow is not only an important supply line but also a trigger for stimulating the metabolic and other processes regulating feto-placental metabolism and growth. Studies using the natural laboratory of high altitude are valuable for identifying the physiological and genetic mechanisms involved in human reproductive success. PMID:25602072

Emergence of late-onset placental dysfunction: relationship to the change in uterine artery blood flow resistance between the first and third trimesters.

PubMed

Llurba, Elisa; Turan, Ozhan; Kasdaglis, Tania; Harman, Chris R; Baschat, Ahmet A

2013-06-01

To test if emergence of third-trimester (T3) placental dysfunction is related to the impedance change in uterine artery blood flow resistance between the first trimester (T1) and T3. Mean T1 and T3 uterine artery (mUtA) pulsatility index (PI) was measured in 1098 singletons. Each patient's individual mUtA-PI change was calculated ([(T3 PI - T1 PI/interval in days)] × 100; ΔmUtA-PI). This parameter and T1 and T3 mUtA-PI z-scores were related to placenta-related disease (PRD) and to constitutionally small neonates (CS). Forty-seven (5%) women had PRD and 83 (8.7%) delivered a CS neonate. T1 and T3 mUtA-PI z-scores were higher with PRD (0.418 versus -0.097 and 1.06 versus -0.13, p < 0.001 for all). Change in mUtA-PI (ΔmUtA PI) was similar for patients with PRD. However, the prevalence of PRD doubled with rising ΔmUtA-PI (11.1% versus 5.2%, p = 0.041). T3 uterine artery Doppler performs significantly better in detecting patients at risk for late-onset PRD than T1 or the gestational age change in uterine artery Doppler resistance This suggests that a proportion of late emerging PRD is not amenable to early screening by uterine artery Doppler. Further research is essential to identify the optimal screening strategy for late-onset placental dysfunction. Thieme Medical Publishers 333 Seventh Avenue, New York, NY 10001, USA.

Structure and permeation mechanism of a mammalian urea transporter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Levin, Elena J.; Cao, Yu; Enkavi, Giray

2012-09-17

As an adaptation to infrequent access to water, terrestrial mammals produce urine that is hyperosmotic to plasma. To prevent osmotic diuresis by the large quantity of urea generated by protein catabolism, the kidney epithelia contain facilitative urea transporters (UTs) that allow rapid equilibration between the urinary space and the hyperosmotic interstitium. Here we report the first X-ray crystal structure of a mammalian UT, UT-B, at a resolution of 2.36 {angstrom}. UT-B is a homotrimer and each protomer contains a urea conduction pore with a narrow selectivity filter. Structural analyses and molecular dynamics simulations showed that the selectivity filter has twomore » urea binding sites separated by an approximately 5.0 kcal/mol energy barrier. Functional studies showed that the rate of urea conduction in UT-B is increased by hypoosmotic stress, and that the site of osmoregulation coincides with the location of the energy barrier.« less

Structure and permeation mechanism of a mammalian urea transporter

PubMed Central

Levin, Elena J.; Cao, Yu; Enkavi, Giray; Quick, Matthias; Pan, Yaping; Tajkhorshid, Emad; Zhou, Ming

2012-01-01

As an adaptation to infrequent access to water, terrestrial mammals produce urine that is hyperosmotic to plasma. To prevent osmotic diuresis by the large quantity of urea generated by protein catabolism, the kidney epithelia contain facilitative urea transporters (UTs) that allow rapid equilibration between the urinary space and the hyperosmotic interstitium. Here we report the first X-ray crystal structure of a mammalian UT, UT-B, at a resolution of 2.36 Å. UT-B is a homotrimer and each protomer contains a urea conduction pore with a narrow selectivity filter. Structural analyses and molecular dynamics simulations showed that the selectivity filter has two urea binding sites separated by an approximately 5.0 kcal/mol energy barrier. Functional studies showed that the rate of urea conduction in UT-B is increased by hypoosmotic stress, and that the site of osmoregulation coincides with the location of the energy barrier. PMID:22733730

Simultaneous observation of the poleward expansion of substorm electrojet activity and the tailward expansion of current sheet disruption in the near-earth magnetotail

NASA Technical Reports Server (NTRS)

Lopez, R. E.; Koskinen, H. E. J.; Pulkkinen, T. I.; Bosinger, T.; Mcentire, R. W.; Potemra, T. A.

1993-01-01

A substorm that occurred on 7 June 1985 at 2209 UT for which simultaneous measurements from ground stations and CCE are available is considered. The event occurred during a close conjunction between CCE, the EISCAT magnetometer cross, and the STARE radar, allowing a detailed comparison of satellite and ground-based data. Two discrete activations took place during the first few minutes of this substorm: the expansion phase onset at 2209 UT and an intensification at 2212 UT, corresponding to a poleward expansion of activity. The energetic particle data indicate that the active region of the magnetotail during the 2212 UT intensification was located tailward of the active region at 2209 UT. This is direct evidence for a correspondence between tailward expansion of localized activity in the near-earth magnetotail (current disruption and particle energization) and poleward expansion of activity (electrojet formation) in the ionosphere.

Microstructural and mechanical characterization of postweld heat-treated thermite weld in rails

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ilic, N.; Jovanovic, M.T.; Todorovic, M.

1999-10-01

This paper describes a comparative study of the hardness characteristics, mechanical properties, microstructures, and fracture mechanisms of the thermite welded rail steel joints before and after heat treatment. It has been found that heat treatment of the welded joint improves the mechanical properties (UTS and elongation), and changes the fracture mechanism from brittle to ductile. Improved strength and elongation are attributed to the finer ferrite-pearlite microstructure and the different fracture mechanism. Microporosity and numerous inclusions were seen on the fracture surface of the welded joint. The chemical composition of the inclusions indicated that the molten thermite mixture had reacted withmore » the magnesite lining of the ladle and the feeder.« less

Theoretical Radiation Patterns of NAVSPASUR Transmitter Antennas

DTIC Science & Technology

1988-11-30

NAVSPASUR handbooks[7,8]. Our calculated north-south 3 dB far-field beamwidth of 0.0210 agrees with the reported value, as does the first sidelobe level ...in Fig. 18, has far-field 3 dB beamwidth and first side lobe levels which agree with the reported values 0.220 and -13 dB, respectively. 3 Again, the...L. Berg .::, UT1 rAT pu;blic release 3 Novemer 198e I 30 November 1988 I I I = i i I I I29I /I I I EXECUTIVE SUMMARY I Interferometrics Inc. has

75 FR 58433 - Notice of Inventory Completion: Brigham Young University, Museum of Peoples and Cultures, Provo, UT

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-24

... University, Museum of Peoples and Cultures, Provo, UT AGENCY: National Park Service, Interior. ACTION: Notice... objects in the possession of the Brigham Young University, Museum of Peoples and Cultures, Provo, UT. The..., 25 U.S.C. 3003(d)(3). The determinations in this notice are the sole responsibility of the museum...

VizieR Online Data Catalog: Discovery of 2 hot Jupiters KELT-14b & KELT-15b (Rodriguez+, 2016)

NASA Astrophysics Data System (ADS)

Rodriguez, J. E.; Colon, K. D.; Stassun, K. G.; Wright, D.; Cargile, P. A.; Bayliss, D.; Pepper, J.; Collins, K. A.; Kuhn, R. B.; Lund, M. B.; Siverd, R. J.; Zhou, G.; Gaudi, B. S.; Tinney, C. G.; Penev, K.; Tan, T. G.; Stockdale, C.; Curtis, I. A.; James, D.; Udry, S.; Segransan, D.; Bieryla, A.; Latham, D. W.; Beatty, T. G.; Eastman, J. D.; Myers, G.; Bartz, J.; Bento, J.; Jensen, E. L. N.; Oberst, T. E.; Stevens, D. J.

2018-04-01

Spectroscopic observations of KELT-14 and KELT-15 were carried out using the CYCLOPS2 fiber feed with the UCLES spectrograph instrument on the Anglo-Australian Telescope (AAT) over two observing runs: UT 2015 February 02-UT 2015 March 01 and UT 2015 May 6-UT 2015 May 13. The instrumental set-up and observing strategy for these observations closely follow that described in earlier CYCLOPS RV papers (Addison et al. 2013ApJ...774L...9A, 2014ApJ...792..112A). CORALIE is a fiber-fed echelle spectrograph (Queloz et al. 2001Msngr.105....1Q) attached to the Swiss 1.2 m Leonard Euler telescope at the ESO La Silla Observatory in Chile. It has a spectral resolution of R~60000, a wavelength range of 3900-6800 Å, and is able to measure radial velocities of bright stars to a precision of 3 m/s or better (Pepe et al. 2002, J/A+A/388/632). We obtained spectra at five epochs of KELT-15 from UT 2015 September 02 to UT 2015 September 14. (3 data files).

Structural, optical, thermal and mechanical properties of Urea tartaric acid single crystals.

PubMed

Vinothkumar, P; Rajeswari, K; Kumar, R Mohan; Bhaskaran, A

2015-06-15

Urea tartaric acid (UT) an organic nonlinear optical (NLO) material was synthesized from aqueous solution and the crystals were grown by the slow evaporation technique. The single crystal X-ray diffraction (XRD) analysis revealed that the UT crystal belongs to the orthorhombic system. The functional groups of UT have been identified by the Fourier transform infrared spectral studies. The optical transparent window in the visible and near the IR regions was investigated. The transmittance of UT has been used to calculate the refractive index (n) as a function of the wavelength. The nonlinear optical property of the grown crystal has been confirmed by the Kurtz powder second harmonic generation test. The birefringence of the crystal was determined using a tungsten halogen lamp source. The laser induced surface damage threshold for the grown crystal was measured using the Nd:YAG laser. The anisotropic in mechanical property of the grown crystals was studied using Vicker's microhardness tester at different planes. The etch pit density of UT crystals was investigated. The thermal behavior of UT was investigated using the TG-DTA and DSC studies. Copyright © 2015 Elsevier B.V. All rights reserved.

Comparative Study of the December 28, 2015 - January 2, 2016 and April 7 - 11, 1997 Sun-Earth Connection Events

NASA Astrophysics Data System (ADS)

Berdichevsky, D. B.; Richardson, I. G.; Farrugia, C. J.

2016-12-01

A Sun-Earth connection event started on December 28, 2015 in association with a M1.8 X-ray flare, commencing at 1120 UT detected by the GOES Environmental satellites, and a partial halo coronal mass ejection (CME) observed from 1200 UT by the SOHO LASCO coronographs. SDO AIA observations indicate that this event was located at W11S22. The related interplanetary coronal mass ejection (ICME) drove an above average strength fast-forward interplanetary shock observed by the Wind spacecraft at the start of Dec 31. This shock also appears to have accelerated solar energetic particles; ACE/EPAM observations show that these energetic particles peaked at shock passage. The shock driver, i.e. the ICME, appears to have impacted the Earth's environment near 17 UT on December 31. This ICME seems to have included several substructures and possibly extended to around midday on January 2, 2016. The impact of the ICME produced lively auroras at low Earth latitudes in the Western-North hemisphere. The associated strong magnetic storm was due to the leading part of the ICME maintaining a southward-oriented magnetic field for several hours. The purpose of this study is to compare and contrast this event with the April 7-11, 1997 Sun-Earth connection event previously discussed by Berdichevsky et al. (1998) which included the passage of an ICME at Earth with a persistent northward, rather than southward, magnetic-field and produced an unusually long-lasting compression of the Earth's magnetosphere. Berdichevsky, D, J.-L. Bougeret, J.-P. Delaboudinière, N. Fox, M. Kaiser, R. Lepping, D. Michels, S. Plunkett, D. Reames, M. Reiner, I. Richardson, G. Rostoker, J. Steinberg, B. Thompson, and T. von Rosenvinge, Evidence for multiple ejecta: April 7-11, 1997, ISTP Sun-Earth connection event GRL, 25, 2473-6, 1998.

VizieR Online Data Catalog: Imaging and spectroscopy in Lynx W (Jorgensen+, 2014)

NASA Astrophysics Data System (ADS)

Jorgensen, I.; Chiboucas, K.; Toft, S.; Bergmann, M.; Zirm, A.; Schiavon, R. P.; Grutzbauch, R.

2017-01-01

Ground-based imaging of RX J0848.6+4453 was obtained primarily to show the performance gain provided by replacing the original E2V charge-coupled devices (E2V CCDs) in Gemini Multi-Object Spectrograph on Gemini North (GMOS-N) with E2V Deep Depletion CCDs (E2V DD CCDs). This replacement was done in 2011 October. Imaging of RX J0848.6+4453 was obtained with the original E2V CCDs in 2011 October (UT 2011 Oct 1 to 2011 Oct 2; Program ID: GN-2011B-DD-3) and repeated with the E2V DD CCDs in 2011 November. The imaging was done in the z' filter. For the observations with the original E2V CCDs the total exposure time was 60 minutes (obtained as 12 five-minute exposures) and the co-added image had an image quality of FWHM=0.52'' measured from point sources in the field. For the E2V DD CCDs a total exposure time of 55 minutes was obtained and the resulting image quality was FWHM=0.51''. Imaging of RX J0848.6+4453 was also obtained with Hubble Space Telescope /Advanced Camera for Surveys (HST/ACS using the filters F775W and F850LP) under the program ID 9919. The spectroscopic observations were obtained in multi-object spectroscopic (MOS) mode with GMOS-N (UT 2011 Nov 24 to 2012 Jan 4, Program ID: GN-2011B-DD-5; UT 2013 Mar 9 to 2013 May 18, Program ID: GN-2013A-Q-65). Table10 lists the photometric parameters for the spectroscopic sample as derived from the HST/ACS observations in F850LP and F775W. Tables 11 and 12 list the results from the template fitting and the derived line strengths, respectively. (3 data files).

Vertical profile of tropospheric ozone derived from synergetic retrieval using three different wavelength ranges, UV, IR, and microwave: sensitivity study for satellite observation

NASA Astrophysics Data System (ADS)

Sato, Tomohiro O.; Sato, Takao M.; Sagawa, Hideo; Noguchi, Katsuyuki; Saitoh, Naoko; Irie, Hitoshi; Kita, Kazuyuki; Mahani, Mona E.; Zettsu, Koji; Imasu, Ryoichi; Hayashida, Sachiko; Kasai, Yasuko

2018-03-01

We performed a feasibility study of constraining the vertical profile of the tropospheric ozone by using a synergetic retrieval method on multiple spectra, i.e., ultraviolet (UV), thermal infrared (TIR), and microwave (MW) ranges, measured from space. This work provides, for the first time, a quantitative evaluation of the retrieval sensitivity of the tropospheric ozone by adding the MW measurement to the UV and TIR measurements. Two observation points in East Asia (one in an urban area and one in an ocean area) and two observation times (one during summer and one during winter) were assumed. Geometry of line of sight was nadir down-looking for the UV and TIR measurements, and limb sounding for the MW measurement. The retrieval sensitivities of the ozone profiles in the upper troposphere (UT), middle troposphere (MT), and lowermost troposphere (LMT) were estimated using the degree of freedom for signal (DFS), the pressure of maximum sensitivity, reduction rate of error from the a priori error, and the averaging kernel matrix, derived based on the optimal estimation method. The measurement noise levels were assumed to be the same as those for currently available instruments. The weighting functions for the UV, TIR, and MW ranges were calculated using the SCIATRAN radiative transfer model, the Line-By-Line Radiative Transfer Model (LBLRTM), and the Advanced Model for Atmospheric Terahertz Radiation Analysis and Simulation (AMATERASU), respectively. The DFS value was increased by approximately 96, 23, and 30 % by adding the MW measurements to the combination of UV and TIR measurements in the UT, MT, and LMT regions, respectively. The MW measurement increased the DFS value of the LMT ozone; nevertheless, the MW measurement alone has no sensitivity to the LMT ozone. The pressure of maximum sensitivity value for the LMT ozone was also increased by adding the MW measurement. These findings indicate that better information on LMT ozone can be obtained by adding constraints on the UT and MT ozone from the MW measurement. The results of this study are applicable to the upcoming air-quality monitoring missions, APOLLO, GMAP-Asia, and uvSCOPE.

Automated Analysis of dUT1 from IVS Intensive Sessions with VieVS

NASA Astrophysics Data System (ADS)

Uunila, M.; Haas, R.; Kareinen, N.; Lindfors, T.

2012-12-01

The Vienna VLBI Software (VieVS) version 1d is used in its batch mode to analyze IVS Intensive sessions automatically to derive the Earth rotation parameter dUT1. The automation process uses a shell script that is run daily by a cron process. The goal is to achieve dUT1 results as soon as the NGS file is fetched from the VieVS server. Three types of analysis strategies, called S-1, S-2 and S-3, are used in the process in order to compare different parameterizations and to improve the latency of deriving dUT1. The S-1 analysis strategy uses as a priori Earth orientation parameters the values provided by the EOP-file "finals2000A", uses as mapping function the Global Mapping Function (GMF), and does not apply atmospheric loading. The S-2 analysis strategy differs from the first analysis strategy by using the Vienna Mapping function (VM1) instead of the GMF and by applying atmospheric loading. The S-3 analysis strategy differs from the second approach by using the IERS C04 values as a priori Earth orientation parameters. All other parameters are treated identically for the three analysis strategies. The latency of the results for the first analysis strategy is 2-3 days from the end of a session and is dominated by the time that is necessary to correlate the observational data and to pre-process the data, i.e. to provide an NGS file where group delay ambiguities are resolved and the ionospheric effects are corrected. The latency of the results for the second strategy is slightly worse, about 3-4 days, mainly due to the time that it takes until VMF1 and atmospheric loading based on ECMWF analysis data are available. The latency of the results for the third strategy is even worse, about 30 days, and is dominated by the time that it takes until the IERS C04 data are available. The RMS values of the formal errors of the three strategies in the case of INT1 sessions are 21, 22, and 17 microseconds for strategies 1, 2 and 3, respectively. The formal error of S-3 is the best, but the latency is the worst. To enhance the latency of the S-1, we currently are working on including the necessary pre-processing steps, i.e. group delay ambiguity resolution and ionospheric correction, directly into VieVS. The results of the automated analysis are provided both as data files and in graphical form on the Metsähovi Web pages http://www.metsahovi.fi/vlbi/vievs/results GMF, .../results VM1, and .../results C04, respectively.

Approaches to reduce urinary tract injury during management of placenta accreta, increta, and percreta: a systematic review.

PubMed

Tam Tam, Kiran Babu; Dozier, James; Martin, James Nello

2012-04-01

A systematic review of the literature was conducted to answer the following question: are there enhancements to standard peripartum hysterectomy technique that minimize unintentional urinary tract (UT) injury in pregnancies complicated by invasive placental attachment (INPLAT)? A PubMed search of English language articles on INPLAT published by June 2010 was conducted. Data regarding the following parameters was required for inclusion in the quantitative analysis of the review's objective: (1) type of INPLAT, (2) details pertaining to medical and surgical management of INPLAT, and (3) complications, if any, associated with management. An attempt was made to identify approaches that may lower the risk of unintentional UT injury. Most cases (285 of 292) were managed by hysterectomy. There were 83 (29%) cases of unintentional UT injury. Antenatal diagnosis of INPLAT lowered the rate of UT injury (39% vs. 63%; P = 0.04). Information regarding surgical technique or medical management was available for 90 cases; 14 of these underwent a standard hysterectomy technique. Methotrexate treatment and 11 modifications of the surgical technique were associated with 16% unintentional UT injury rate as opposed to 57% for standard hysterectomy (P = 0.002). The use of ureteral stents reduced risk of urologic injury (P = 0.01). Multiple logistic regression analysis identified antenatal diagnosis as the significant predictor of an intact UT. Antenatal diagnosis of INPLAT is paramount to minimize UT injury. Utilization of management modifications identified in this review may reduce urologic injury due to INPLAT.

An extract of Urtica dioica L. mitigates obesity induced insulin resistance in mice skeletal muscle via protein phosphatase 2A (PP2A)

PubMed Central

Obanda, Diana N.; Ribnicky, David; Yu, Yongmei; Stephens, Jacqueline; Cefalu, William T.

2016-01-01

The leaf extract of Urtica dioica L. (UT) has been reported to improve glucose homeostasis in vivo, but definitive studies on efficacy and mechanism of action are lacking. We investigated the effects of UT on obesity- induced insulin resistance in skeletal muscle. Male C57BL/6J mice were divided into three groups: low-fat diet (LFD), high-fat diet (HFD) and HFD supplemented with UT. Body weight, body composition, plasma glucose and plasma insulin were monitored. Skeletal muscle (gastrocnemius) was analyzed for insulin sensitivity, ceramide accumulation and the post translational modification and activity of protein phosphatase 2A (PP2A). PP2A is activated by ceramides and dephosphorylates Akt. C2C12 myotubes exposed to excess free fatty acids with or without UT were also evaluated for insulin signaling and modulation of PP2A. The HFD induced insulin resistance, increased fasting plasma glucose, enhanced ceramide accumulation and PP2A activity in skeletal muscle. Supplementation with UT improved plasma glucose homeostasis and enhanced skeletal muscle insulin sensitivity without affecting body weight and body composition. In myotubes, UT attenuated the ability of FFAs to induce insulin resistance and PP2A hyperactivity without affecting ceramide accumulation and PP2A expression. UT decreased PP2A activity through posttranslational modification that was accompanied by a reduction in Akt dephosphorylation. PMID:26916435

The use of fluidized sand bed as an innovative technique for heat treating aluminum based castings

NASA Astrophysics Data System (ADS)

Ragab, Khaled

The current study was carried out to arrive at a better understanding of the influences of the fluidized sand bed heat treatment on the tensile properties and quality indices of A356.2 and B319.2 casting alloys. For the purposes of validating the use of fluidized sand bed furnaces in industrial applications for heat treatment of 356 and 319 castings, the tensile properties and the quality indices of these alloys were correlated with the most common metallurgical parameters, such as strontium modification, grain refining, solutionizing time, aging parameters and quenching media. Traditional heat treatment technology, employing circulating air convection furnaces, was used to establish a relevant comparison with fluidized sand beds for the heat treatment of the alloys investigated, employing T6 continuous aging cycles or multi-temperature aging cycles. Quality charts were used to predict and/or select the best heat treatment conditions and techniques to be applied in industry in order to obtain the optimum properties required for particular engineering applications. The results revealed that the strength values achieved in T6-tempered 319 and 356 alloys are more responsive to fluidized bed (FB) heat treatment than to conventional convection furnace (CF) treatment for solution treatment times of up to 8 hours. Beyond this solution time, no noticeable difference in properties is observed with the two techniques. A significant increase in strength is observed in the FB heat-treated samples after short aging times of 0.5 and 1 hour, the trend continuing up to 5 hours. The 319 alloys show signs of overaging after 8 hours of aging using a conventional furnace, whereas with a fluidized bed, overaging occurs after 12 hours. Analysis of the tensile properties in terms of quality index charts showed that both modified and non-modified 319 and 356 alloys display the same, or better, quality, after only a 2-hr treatment in an FB compared to 10 hours when using a CF. The quality values of the 356 alloys are more responsive to the FB technique than 319 alloys through long aging times of up to 5 hours. The 319 alloys heat-treated in an FB, however, show better quality values after 0.5 hour of aging and for solution treatment times of up to 5 hours than those treated using a CF. With regard to the quality charts of 319 alloys, heat-treated samples show that increasing the aging time up to peak-strength, i.e. 8 and 12 hours in a CF and an FB, respectively, results in increasing in the alloy strength with a decrease in the quality values, for each of the solution heat treatment times used. The statistical analysis of the results reveals that modification and heating rate of the heat treatment technique have the greatest positive effects on the quality values of the 356 alloys. The use of a fluidized sand bed for the direct quenching-aging treatment of A356.2 and B319.2 casting alloys yields greater UTS and YS values compared to conventional furnace quenched alloys. The strength values of T6 tempered A356 and B319 alloys are greater when quenched in water compared to those quenched in an FB or CF. For the same aging conditions (170°C/4h), the fluidized bed quenched-aged 319 and 356 alloys show nearly the same or better strength values than those quenched in water and then aged in a CF or an FB. Based on the quality charts developed for alloys subjected to different quenching media, higher quality index values are obtained by water-quenched T6-tempered A356 alloys, and conventional furnace quenched-aged T6-tempered B319 alloys, respectively. The modification factor has the most significant effect on the quality results of the alloys investigated, for all heat treatment cycles, as compared to other metallurgical parameters. The results of alloys subjected to multi-temperature aging cycles reveal that the strength results obtained after the T6 continuous aging treatment of A356 alloys are not improved by means of multi-temperature aging cycles, indicating therefore that the optimum properties are obtained using a T6 aging treatment. The optimum strength properties of B319.2 alloys, however, is obtained by applying multi-temperature aging cycles such as, for example, 230°C/2h followed by 180°C/8h, rather than T6 aging treatment. In the case of multi-temperature aging cycles, the modification factor has the most significant role in improving the quality index values of 356 and 319 alloys. The FB heat-treated alloys have the highest strength values for all heat treatment cycles compared to CF heat-treated alloys; however, the FB has no significant effect on the quality values of 319 alloys compared to the CF. Regarding the interaction plots for multi-temperature aging cycles, the most significant factors that have a positive effect on the quality values of 356 alloys are modification and the 230°C/2h + 180°C/8h multi-temperature aging cycle. (Abstract shortened by UMI.)

Hypovolemic intolerance to lower body negative pressure in female runners.

PubMed

Morikawa, T; Sagawa, S; Torii, R; Endo, Y; Yamazaki, F; Shiraki, K

2001-12-01

An attenuated baroreflex response and orthostatic intolerance have been reported in endurance-trained male athletes; however, it is still unknown whether this occurs also in females. The purpose of the present study was to examine whether endurance exercise-trained women had a predisposition to orthostatic compromise, and if so, what causative factor(s) may induce orthostatic intolerance. We studied cardiovascular and hormonal responses to graded lower body negative pressure (LBNP) (0 to -60 mm Hg) in 26 middle-distance female runners (18.6 +/- 0.1 yr) as the exercise-trained (ET) subjects and 23 age-matched untrained (UT) control subjects. On the basis of the occurrence of syncope episodes during LBNP, ET and UT subjects were further allocated to two groups; ET with presyncope (ET+syncope) and without presyncope (ET-syncope) and UT with presyncope (UT+syncope) and without presyncope (UT-syncope). Occurrence of presyncope episodes during LBNP was higher in ET (65.4%, P < 0.05) than that for UT (34.8%). Leg compliance was higher (P < 0.05) in ET than in UT. LBNP reduced stroke volume (SV) more (P < 0.05), increased heart rate (HR) higher (P < 0.05), and increased forearm vascular resistance (FVR) more in ET+syncope as compared with the other groups. Response of vasoactive hormones to LBNP was higher in ET+syncope (P < 0.05) than that of the other groups except for norepinephrine (NE); high in both ET+syncope and UT+syncope. The relationship between SV and NE, an index of sympathetic neuronal response, had no training-related changes during LBNP. We conclude that exercise-trained females have a high incidence of orthostatic intolerance during LBNP, with a greater reduction of SV independent of changes in baroreflex and neurohumoral function. A lower incidence of LBNP intolerance in UT may be accounted for by a lower reduction of SV during LBNP. An increase in leg compliance in the exercise-trained females may play an important role in inducing pronounced reduction of SV and hence the intolerance to LBNP.

Hypoxia-Inducible Factor Pathway Inhibition Resolves Tumor Hypoxia and Improves Local Tumor Control After Single-Dose Irradiation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Helbig, Linda; Department of Radiation Oncology, University Hospital Carl Gustav Carus, Technische Universität Dresden, Dresden; Koi, Lydia

2014-01-01

Purpose: To study the effects of BAY-84-7296, a novel orally bioavailable inhibitor of mitochondrial complex I and hypoxia-inducible factor 1 (HIF-1) activity, on hypoxia, microenvironment, and radiation response of tumors. Methods and Materials: UT-SCC-5 and UT-SCC-14 human squamous cell carcinomas were transplanted subcutaneously in nude mice. When tumors reached 4 mm in diameter BAY-84-7296 (Bayer Pharma AG) or carrier was daily administered to the animals. At 7 mm tumors were either excised for Western blot and immunohistologic investigations or were irradiated with single doses. After irradiation animals were randomized to receive BAY-84-7296 maintenance or carrier. Local tumor control was evaluatedmore » 150 days after irradiation, and the dose to control 50% of tumors (TCD{sub 50}) was calculated. Results: BAY-84-7296 decreased nuclear HIF-1α expression. Daily administration of inhibitor for approximately 2 weeks resulted in a marked decrease of pimonidazole hypoxic fraction in UT-SCC-5 (0.5% vs 21%, P<.0001) and in UT-SCC-14 (0.3% vs 19%, P<.0001). This decrease was accompanied by a significant increase in fraction of perfused vessels in UT-SCC-14 but not in UT-SCC-5. Bromodeoxyuridine and Ki67 labeling indices were significantly reduced only in UT-SCC-5. No significant changes were observed in vascular area or necrosis. BAY-84-7296 before single-dose irradiation significantly decreased TCD{sub 50}, with an enhancement ratio of 1.37 (95% confidence interval [CI] 1.13-1.72) in UT-SCC-5 and of 1.55 (95% CI 1.26-1.94) in UT-SCC-14. BAY-84-7296 maintenance after irradiation did not further decrease TCD{sub 50}. Conclusions: BAY-84-7296 resulted in a marked decrease in tumor hypoxia and substantially reduced radioresistance of tumor cells with the capacity to cause a local recurrence after irradiation. The data suggest that reduction of cellular hypoxia tolerance by BAY-84-7296 may represent the primary biological mechanism underlying the observed enhancement of radiation response. Whether this mechanism contributes to the improved outcome of fractionated chemoradiation therapy warrants further investigation.« less

Increased Upper Trapezius Muscle Stiffness in Overhead Athletes with Rotator Cuff Tendinopathy

PubMed Central

Leong, Hio Teng; Hug, François; Fu, Siu Ngor

2016-01-01

Although excessive tension of the upper trapezius (UT) is thought to contribute to rotator cuff tendinopathy, no study examined UT tension in athletes with and without rotator cuff tendinopathy. Here we used UT shear modulus measured using ultrasound shear wave elastography as an index of muscle stiffness/tension. The aims of this study were twofold: 1) to determine whether the UT muscle shear modulus is altered in athletes with rotator cuff tendinopathy compared to asymptomatic athletes, and 2) to detect optimal cut-off points of UT shear modulus in identifying athletes with rotator cuff tendinopathy. Forty-three male volleyball players (17 asymptomatic and 26 with rotator cuff tendinopathy, mean age = 22.9±3.5 years) participated in the study. UT shear modulus was quantified during active arm holding at 30° and 60° of shoulder abduction and passive arm positioning at 0°, 30° and 60° of shoulder abduction. During the active tasks, the UT shear modulus was higher in athletes with rotator cuff tendinopathy than the asymptomatic athletes (p = 0.002), regardless the arm position. During the passive tasks, athletes with rotator cuff tendinopathy exhibited a higher UT shear modulus than asymptomatic athletes only at 0° of shoulder abduction (13.0±2.5 kPa vs 10.2±1.8 kPa, p = 0.001). When considering the active task, an optimal cut-off shear modulus of 12.0 kPa at 30° of shoulder abduction (sensitivity = 0.84, specificity = 0.57, AUC = 0.757, p = 0.008) and 9.5 kPa at 60° of shoulder abduction (sensitivity = 0.88, specificity = 0.67, AUC = 0.816, p = 0.002) was detected. When considering the passive task at 0° of shoulder abduction, a cut-off of 12.2 kPa was found (sensitivity = 0.73, AUC = 0.817, p = 0.001). Findings from the present study show that monitoring passive and active UT muscle shear modulus may provide important information for the prevention/rehabilitation of rotator cuff tendinopathy. PMID:27159276

Increased Upper Trapezius Muscle Stiffness in Overhead Athletes with Rotator Cuff Tendinopathy.

PubMed

Leong, Hio Teng; Hug, François; Fu, Siu Ngor

2016-01-01

Although excessive tension of the upper trapezius (UT) is thought to contribute to rotator cuff tendinopathy, no study examined UT tension in athletes with and without rotator cuff tendinopathy. Here we used UT shear modulus measured using ultrasound shear wave elastography as an index of muscle stiffness/tension. The aims of this study were twofold: 1) to determine whether the UT muscle shear modulus is altered in athletes with rotator cuff tendinopathy compared to asymptomatic athletes, and 2) to detect optimal cut-off points of UT shear modulus in identifying athletes with rotator cuff tendinopathy. Forty-three male volleyball players (17 asymptomatic and 26 with rotator cuff tendinopathy, mean age = 22.9±3.5 years) participated in the study. UT shear modulus was quantified during active arm holding at 30° and 60° of shoulder abduction and passive arm positioning at 0°, 30° and 60° of shoulder abduction. During the active tasks, the UT shear modulus was higher in athletes with rotator cuff tendinopathy than the asymptomatic athletes (p = 0.002), regardless the arm position. During the passive tasks, athletes with rotator cuff tendinopathy exhibited a higher UT shear modulus than asymptomatic athletes only at 0° of shoulder abduction (13.0±2.5 kPa vs 10.2±1.8 kPa, p = 0.001). When considering the active task, an optimal cut-off shear modulus of 12.0 kPa at 30° of shoulder abduction (sensitivity = 0.84, specificity = 0.57, AUC = 0.757, p = 0.008) and 9.5 kPa at 60° of shoulder abduction (sensitivity = 0.88, specificity = 0.67, AUC = 0.816, p = 0.002) was detected. When considering the passive task at 0° of shoulder abduction, a cut-off of 12.2 kPa was found (sensitivity = 0.73, AUC = 0.817, p = 0.001). Findings from the present study show that monitoring passive and active UT muscle shear modulus may provide important information for the prevention/rehabilitation of rotator cuff tendinopathy.

The first super geomagnetic storm of solar cycle 24: "The St. Patrick day (17 March 2015)" event

NASA Astrophysics Data System (ADS)

Wu, C. C.; Liou, K.; Socker, D. G.; Howard, R.; Jackson, B. V.; Yu, H. S.; Hutting, L.; Plunkett, S. P.

2015-12-01

The first super geomagnetic storm of solar cycle 24 occurred on the "St. Patrick's day" (17 March 2015). Notably, it was a two-step storm. The source of the storm can be traced back to the solar event on March 15, 2015. At ~2:10 UT on that day, SOHO/LASCO C3 recorded a partial halo corona mass ejection (CME) which was associated with a C9.1/1F flare (S22W25) and a series of type II/IV radio bursts. The propagation speed of this CME is estimated to be ~668 km/s during 02:10 - 06:20 UT (Figure 1). An interplanetary (IP) shock, likely driven by the CME, arrived at the Wind spacecraft at 03:59 UT on 17 March (Figure 2). The arrival of the IP shock at the Earth may have caused a sudden storm commencement (SSC) at 04:45 UT on March 17. The storm intensified (Dst dropped to -80 nT at ~10:00 UT) during the crossing of the CME sheath. Later, the storm recovered slightly (Dst ~ -50 nT) after the IMF turned northward. At 11:01 UT, IMF started turning southward again due to the large magnetic cloud (MC) field itself and caused the second storm intensification, reaching Dst = - 228 nT on March 18. We conclude that the St. Patrick day event is a two-step storm. The first step is associated with the sheath, whereas the second step is associated with the MC. Here, we employ a numerical simulation using the global, three-dimensional (3D), time-dependent, magnetohydrodynamic (MHD) model (H3DMHD, Wu et al. 2007) to study the CME propagation from the Sun to the Earth. The H3DMHD model has been modified so that it can be driven by (solar wind) data at the inner boundary of the computational domain. In this study, we use time varying, 3D solar wind velocity and density reconstructed from STELab, Japan interplanetary scintillation (IPS) data by the University of California, San Diego, and magnetic field at the IPS inner boundary provided by CSSS model closed-loop propagation (Jackson et a., 2015). The simulation result matches well with the in situ solar wind plasma and field data at Wind, in terms of the peak values of the IP shock and its arrival time (Figure 3). The simulation not only helps us to identify the driver of the IP shock, but also demonstrates that the modified H3DMHD model is capable of realistic simulations of large solar event. In this presentation, we will discuss the CME/storm event with detailed data from observations (Wind and SOHO) and our numerical simulation.

Interpretation of Aura satellite observations of CO and aerosol index related to the December 2006 Australia fires

NASA Astrophysics Data System (ADS)

Luo, M.; Boxe, C.; Jiang, J.; Nassar, R.; Livesey, N.

2009-11-01

Enhanced Carbon Monoxide (CO) in the upper troposphere (UT) is shown by collocated Tropospheric Emission Spectrometer (TES) and Microwave Limb Sounder (MLS) measurements near and down-wind from the known wildfire region of SE Australia from 12-19 December 2006. Enhanced UV aerosol index (AI) derived from Ozone Monitoring Instrument (OMI) measurements correlate with these high CO concentrations. HYSPLIT model back trajectories trace selected air parcels to the SE Australia fire region as their initial location, where TES observes enhanced CO in the upper and lower troposphere. Simultaneously, they show a lack of vertical advection along their tracks. TES retrieved CO vertical profiles in the higher and lower southern latitudes are examined together with the averaging kernels and show that TES CO retrievals are most sensitive at approximately 300-400 hPa. The enhanced CO observed by TES at the upper (215 hPa) and lower (681 hPa) troposphere are, therefore, influenced by mid-tropospheric CO. GEOS-Chem model simulations with an 8-day emission inventory, as the wildfire source over Australia, are sampled to the TES/MLS observation times and locations. These simulations only show CO enhancements in the lower troposphere near and down-wind from the wildfire region of SE Australia with drastic underestimates of UT CO. Although CloudSat along-track ice-water content curtains are examined to see whether possible vertical convection events can explain the high UT CO values, sparse observations of collocated Aura CO and CloudSat along-track ice-water content measurements for the single event precludes any conclusive correlation. Vertical convection that uplift fire-induced CO (i.e. most notably referred to as pyro-cumulonimbus, pyroCb) may provide an explanation for the incongruence between these simulations and the TES/MLS observations of enhanced CO in the UT. Future GEOS-Chem simulations are needed to validate this conjecture as the the PyroCb mechanism is currently not incorporated in GEOS-Chem.

Spatio-temporal aerosol particle distributions in the UT/LMS measured by the IAGOS-CARIBIC Observatory

NASA Astrophysics Data System (ADS)

Assmann, D. N.; Hermann, M.; Weigelt, A.; Martinsson, B. G.; Brenninkmeijer, C. A. M.; Rauthe-Schoech, A.; van Velthoven, P. J. F.; Boenisch, H.; Zahn, A.

2016-12-01

Submicrometer aerosol particles in the upper troposphere and lowermost stratosphere (UT/LMS) influence the Earth`s radiation budget directly and, more important, indirectly, by acting as cloud condensation nuclei and by changing trace gas concentrations through heterogeneous chemical processes. Since 1997, regular in situ UT/LMS aerosol particle measurements have been conducted by the Leibniz Institute for Tropospheric Research, Leipzig, Germany and the University of Lund, Sweden, using the the CARIBIC (now IAGOS-CARIBIC) observatory (www.caribic-atmospheric.com) onboard a passenger aircraft. Submicrometer aerosol particle number concentrations and the aerosol particle size distribution are measured using three condensation particle counters and one optical particle size spectrometer. Moreover, particle elemental composition is determined using an aerosol impactor sampler and post-flight ion beam analysis (PIXE, PESA) of the samples in the laboratory. Based on this unique data set, including meteorological analysis, we present representative spatio-temporal distributions of particle number, surface, volume, and elemental concentrations in an altitude of 8-12 km covering a large fraction of the northern hemisphere. We discuss the measured values in the different size regimes with respect to sources and sinks in different regions. Additionally, we calculated highly resolved latitudinal and longitudinal cross sections of the particle number size distribution, probability density functions and trends in particle number concentrations, but also in elemental composition, determined from our regular measurements over more than a decade. Moreover, we present the seasonality of particle number concentration in an equivelent latitude - potential temperature coordinate framework (see figure). The results are interpreted with respect to aerosol microphysics and transport using CARIBIC trace gas data like ozone and water vapour. The influence of clouds in the troposphere and the different stratosphere-troposphere-exchange processes are clearly visible. Besides providing information about UT/LMS aerosol particle sources, transport, and sinks, these distributions can be used to validate remote sensing instruments or global atmospheric aerosol models.

Spatio-temporal aerosol particle distributions in the UT/LMS measured by the IAGOS-CARIBIC Observatory

NASA Astrophysics Data System (ADS)

Assmann, Denise; Hermann, Markus; Weigelt, Andreas; Martinsson, Bengt; Brenninkmeijer, Carl; Rauthe-Schöch, Armin; van Velthoven, Peter; Bönisch, Harald; Zahn, Andreas

2017-04-01

Submicrometer aerosol particles in the upper troposphere and lowermost stratosphere (UT/LMS) influence the Earth`s radiation budget directly and, more important, indirectly, by acting as cloud condensation nuclei and by changing trace gas concentrations through heterogeneous chemical processes. Since 1997, regular in situ UT/LMS aerosol particle measurements have been conducted by the Leibniz Institute for Tropospheric Research, Leipzig, Germany and the University of Lund, Sweden, using the the CARIBIC (now IAGOS-CARIBIC) observatory (www.caribic-atmospheric.com) onboard a passenger aircraft. Submicrometer aerosol particle number concentrations and the aerosol particle size distribution are measured using three condensation particle counters and one optical particle size spectrometer. Moreover, particle elemental composition is determined using an aerosol impactor sampler and post-flight ion beam analysis (PIXE, PESA) of the samples in the laboratory. Based on this unique data set, including meteorological analysis, we present representative spatio-temporal distributions of particle number, surface, volume and elemental concentrations in an altitude of 8-12 km covering a large fraction of the northern hemisphere. We discuss the measured values in the different size regimes with respect to sources and sinks in different regions. Additionally, we calculated highly resolved latitudinal and longitudinal cross sections of the particle number size distribution, probability density functions and trends in particle number concentrations, but also in elemental composition, determined from our regular measurements over more than a decade. Moreover, we generated seasonal contour plots for particle number concentrations, the potential temperature, and the equivalent latitude. The results are interpreted with respect to aerosol microphysics and transport using CARIBIC trace gas data like ozone and water vapour. The influence of clouds in the troposphere and the different stratosphere-troposphere-exchange processes is clearly visible. Besides providing information about UT/LMS aerosol particle sources, transport, and sinks, these distributions can be used to validate remote sensing instruments or global atmospheric aerosol models.

Preliminary report of 48-hours Atosiban administration in spontaneous preterm labor - Doppler blood flow assessment of placental and fetal circulation.

PubMed

Grzesiak, Mariusz; Wilczynski, Jan

2013-01-01

The aims were to investigate whether there are any changes in placental and fetal circulation during Atosiban tocolysis within the first 48 hours of therapy. Detailed Doppler evaluation of placental and fetal circulation was performed prior to Atosiban administration and thereafter at 24 and 48 hours. Maternal heart rate and the pulsatility index (PI) in both uterine arteries (R-UtA, L-UtA) were assessed. Fetal heart rate (FHR), the resistance (RI) and pulsatility index (PI) of umbilical (UA) and middle cerebral artery (MCA) were measured. Additionally cerebroplacental ratio was calculated. E-wave/A-wave ratio (E/A) for atrioventricular valves, the myocardial performance index (MPI) and shortening fraction (SF) for both ventricles were calculated for both ventricles independently. To determine changes over time in all study variables analysis of variance (ANOVA) for repeated measurements followed by Tukey-Kramer's post hoc test was used. The effects of additional clinical covariates were checked. Maternal heart rate and blood flow in (R-UtA/L-UtA) were not altered significantly during Atosiban administration. No significant changes in FHR as well as Doppler parameters (RI, PI, PSV) in UA and MCA were recorded after 24/48 hours of tocolytic treatment. The mean values of cerebroplacental ratio (CPR) remained unaltered during treatment. Detailed evaluation of fetal cardiac function parameters (E/A, SF, MPI) calculated independently for both ventricles, revealed no significant changes over the time. To our best knowledge this study has been first evaluation of placental and fetal circulation with assessment of cardiac hemodynamic function during 48-hours administration of Atosiban. This kind of tocolysis treatment seems not to alter uterine nor fetal arterial blood flow pattern seriously. Hemodynamic cardiac activity in fetuses has remained unaffected. We cannot conclude definitely that there are absolutely no changes in the fetal hemodynamic condition due to Atosiban. Further studies should be performed to verify its possible influence on fetal venous blood flow.

The First Use of Coordinated Ionospheric Radio and Optical Observations Over Italy: Convergence of High-and Low-Latitude Storm-Induced Effects

NASA Astrophysics Data System (ADS)

Cesaroni, C.; Alfonsi, L.; Pezzopane, M.; Martinis, C.; Baumgardner, J.; Wroten, J.; Mendillo, M.; Musicò, E.; Lazzarin, M.; Umbriaco, G.

2017-11-01

Ionospheric storm effects at midlatitudes were analyzed using different ground-based instruments distributed in Italy during the 13-15 November 2012 geomagnetic storm. These included an all-sky imager (ASI) in Asiago (45.8°N, 11.5°E), a network of dual-frequeny Global Navigation Satellite Systems receivers (Rete Integrata Nazionale GPS network), and ionosondes in Rome (41.8°N, 12.5°E) and San Vito (40.6°N, 17.8°E). GPS measurements showed an unusual enhancement of total electron content (TEC) in southern Italy, during the nights of 14 and 15 November. The ASI observed colocated enhancements of 630 nm airglow at the same time, as did variations in NmF2 measured by the ionosondes. Moreover, wave-like perturbations were identified propagating from the north. The Ensemble Empirical Mode Decomposition, applied to TEC values revealed the presence of traveling ionospheric disturbances (TIDs) propagating southward between 01:30 UT and 03:00 UT on 15 November. These TIDs were characterized by weak TEC oscillations ( ±0.5 TEC unit), period of 45 min, and velocity of 500 m/s typical of large-scale TIDs. Optical images showed enhanced airglow entering the field of view of the ASI from the N-NE at 02:00 UT and propagating to the S-SW, reaching the region covered by the GPS stations after 03:00 UT, when TEC fluctuations are very small ( ±0.2 TEC unit). The enhancement of TEC and airglow observed in southern Italy could be a consequence of a poleward expansion of the northern crest of the equatorial ionization anomaly. The enhanced airglow propagating from the north and the TEC waves resulted from energy injected at auroral latitudes as confirmed by magnetometer observations in Scandinavia.

Protective effect of Uncaria tomentosa extract against oxidative stress and genotoxicity induced by glyphosate-Roundup® using zebrafish (Danio rerio) as a model.

PubMed

Santo, Glaucia Dal; Grotto, Alan; Boligon, Aline A; Da Costa, Bárbara; Rambo, Cassiano L; Fantini, Emily A; Sauer, Elisa; Lazzarotto, Luan M V; Bertoncello, Kanandra T; Júnior, Osmar Tomazelli; Garcia, Solange C; Siebel, Anna M; Rosemberg, Denis B; Magro, Jacir Dal; Conterato, Greicy M M; Zanatta, Leila

2018-04-01

Oxidative stress and DNA damage are involved in the glyphosate-based herbicide toxicity. Uncaria tomentosa (UT; Rubiaceae) is a plant species from South America containing bioactive compounds with known beneficial properties. The objective of this work was to evaluate the antioxidant and antigenotoxic potential of UT extract in a model of acute exposure to glyphosate-Roundup® (GR) in zebrafish (Danio rerio). We showed that UT (1.0 mg/mL) prevented the decrease of brain total thiols, the increase of lipid peroxidation in both brain and liver, and the decrease of liver GPx activity caused after 96 h of GR (5.0 mg/L) exposure. In addition, UT partially protected against the increase of micronucleus frequency induced by GR exposure in fish brain. Overall, our results indicate that UT protects against damage induced by a glyphosate-based herbicide by providing antioxidant and antigenotoxic effects, which may be related to the phenolic compounds identified in the extract.

Ultrasonic characterization of engineering performanace of oriented strandboard

NASA Astrophysics Data System (ADS)

Vun, Ronnie Yunheu

Direct-contact (DC) and non-contact (NC) ultrasonic transmission (UT) methods were developed to characterize the structural performance of oriented strandboard (OSB). The UT variable velocity was shown to be sensitive to the physical impediments caused by flake interfacial boundaries and embedded voids. Both attenuation and root mean square (RMS) voltage were good indicators of the "zero void" densification level for OSB, a point of the greatest transmissivity of the stress wave energy. For both DC and NC methods, the predicted densities of the model were validated for spatial distribution over each OSB type. Based on the control limits of +/-10% of the panel average density, density prediction improved with higher resin content (RC) and higher nominal density (ND) levels. From the out-of-limits plots, the predicted in-situ densities produced a reasonably spatial coherence to the measured values. All panels made with ND 0.60 g/cm3 or greater conformed well within the limits, with declining conformity towards lower RC panels. For each composite type made of different particle sizes, the equilibrium moisture content showed a decreasing trend toward smaller particle panels. The attenuation and RMS were good indicators for moisture change and densification level for each composite type. The velocity, sensitive to physical resistance of particle sizes, increased with increasing IB strength and sample density, manifesting the positive influence of layering, resin content, and the negative effect of bark as a constituent. The results of the creep rupture tests on commercial OSB using an acoustic emission (AE) technique indicated that the cumulative AE event count parameter was highly correlated with deflection parameter and appropriately represented the accumulation of incipient damage. Under high stress levels, specimens with high moisture content (MC) sustained the worse damages having the shortest creep rupture time followed by specimens with dynamically rising MC. Defects on the compression-side of the bending specimen were found critical to creep rupture than those on the tension-side. The in-plane fracture patterns tended to follow the defect trenches of low-density valleys, and worsened with greater variability of the horizontal density, indicating the need to measure and control the horizontal density variation within reasonable limits.

The Hale-Bopp comet - an unexpected guest

NASA Astrophysics Data System (ADS)

Gorodetchi, Dumitru

A number of 3 photographs are given of the comewt Hale-Bopp made at UT 1997 March 18.0937 (refractor RT-80(80 cm., 1:10); Fomapan T-800 (DT=10 min). 2) UT 1997 March 18.010; Cassegrain-reflector AT -400 (630, 1:16); film 100 ASA (DT=1 min) 3)UT 1997 April 5.8097; telobiectiv Tair -11 (13,5 cm, 1:2.8); Fomapan T-800 (DT =2 min)

SALT Spectroscopic classification of ASASSN-18lp as a dwarf nova

NASA Astrophysics Data System (ADS)

Buckley, D. A. H.; Gromadzki, M.; Dong, Subo; Stanek, K. Z.

2018-06-01

ASASSN-18lp (AT 2018cex) was discovered by the All Sky Automated Survey for SuperNovae (ASAS-SN, Shappee et al. 2014) on UT 2018-06-05.24 at g 16 mag. It was observed with the Southern African Large Telescope (SALT) using the Robert Stobie Spectrograph on UT 2018-06-05.75 UT (HJD 2458275.2561) employing the PG300 lines/mm grating.

CRTS-II Detection of Increased Optical Activity from CTA 102

NASA Astrophysics Data System (ADS)

Djorgovski, S. G.; Drake, A. J.; Mahabal, A. A.; Graham, M. J.; Christensen, E.; Larson, S. M.

2017-12-01

We report the detection of significant optical brightening of FSRQ CTA 102 by CRTS-II on 2017 Dec. 8.15 UT. At that time CTA 102 was seen to have risen approximately 1.4 mags (to V_CSS = 14.15) compared with previous observations taken on 2017 Nov. 23 UT. Additional survey observations taken on 2017 Dec. 15 UT show CTA 102 at V_CSS = 14.05.

Different weight bearing push-up plus exercises with and without isometric horizontal abduction in subjects with scapular winging: A randomized trial.

PubMed

Choi, Woo-Jeong; Yoon, Tae-Lim; Choi, Sil-Ah; Lee, Ji-Hyun; Cynn, Heon-Seock

2017-07-01

The aim of the present study was to determine whether the application of isometric horizontal abduction (IHA) differentially affected two weight-bearing push-up plus exercises by examining activation of the scapulothoracic muscles in subjects with scapular winging. Fifteen male subjects performed standard push-up plus (SPP) and wall push-up plus (WPP), with and without IHA. Two-way analyses of variance using two within-subject factors were used to determine the statistical significance of observed differences in upper trapezius (UT), pectoralis major (PM), and serratus anterior (SA) muscle activities and UT/SA and PM/SA muscle activity ratios. UT and SA muscle activities were greater during SPP than WPP. PM muscle activity was lower with IHA application. The UT/SA and PM/SA muscle activity ratios were lower during SPP than WPP. The PM/SA muscle activity ratio was lower with IHA application. The results suggest that IHA application using a Thera-Band can effectively reduce PM muscle activity during SPP and WPP exercises. Moreover, the SPP exercise can be used to increase UT and SA muscle activity and reduce the UT/SA and PM/SA muscle activity ratios in subjects with scapular winging. Copyright © 2016 Elsevier Ltd. All rights reserved.

Science alliance: A vital ORNL-UT partnership

DOE Office of Scientific and Technical Information (OSTI.GOV)

Richmond, C.R.; Riedinger, L.; Garritano, T.

1991-01-01

Partnerships between Department of Energy national laboratories and universities have long been keys to advancing scientific research and education in the United States. Perhaps the most enduring and closely knit of these relationships is the one between Oak Ridge National Laboratory and the University of Tennessee at Knoxville. Since its birth in the 1940's, ORNL has had a very special relationship with UT, and today the two institutions have closer ties than virtually any other university and national laboratory. Seven years ago, ORNL and UT began a new era of cooperation by creating the Science Alliance, a Center of Excellencemore » at UT sponsored by the Tennessee Higher Education Commission. As the oldest and largest of these centers, the Science Alliance is the primary vehicle through which Tennessee promotes research and educational collaboration between UT and ORNL. By letting the two institutions pool their intellectual and financial resources, the alliance creates a more fertile scientific environment than either could achieve on its own. Part of the UT College of Liberal Arts, the Science Alliance is composed of four divisions (Biological Sciences, Chemical Sciences, Physical Sciences, and Mathematics and Computer Science) that team 100 of the university's top faculty with their outstanding colleagues from ORNL.« less

The emerging physiological roles of the SLC14A family of urea transporters

PubMed Central

Stewart, Gavin

2011-01-01

In mammals, urea is the main nitrogenous breakdown product of protein catabolism and is produced in the liver. In certain tissues, the movement of urea across cell membranes is specifically mediated by a group of proteins known as the SLC14A family of facilitative urea transporters. These proteins are derived from two distinct genes, UT-A (SLC14A2) and UT-B (SLC14A1). Facilitative urea transporters play an important role in two major physiological processes – urinary concentration and urea nitrogen salvaging. Although UT-A and UT-B transporters both have a similar basic structure and mediate the transport of urea in a facilitative manner, there are a number of significant differences between them. UT-A transporters are mainly found in the kidney, are highly specific for urea, have relatively lower transport rates and are highly regulated at both gene expression and cellular localization levels. In contrast, UT-B transporters are more widespread in their tissue location, transport both urea and water, have a relatively high transport rate, are inhibited by mercurial compounds and currently appear to be less acutely regulated. This review details the fundamental research that has so far been performed to investigate the function and physiological significance of these two types of urea transporters. PMID:21449978

Performance of the Finnish Diabetes Risk Score and a Simplified Finnish Diabetes Risk Score in a Community-Based, Cross-Sectional Programme for Screening of Undiagnosed Type 2 Diabetes Mellitus and Dysglycaemia in Madrid, Spain: The SPREDIA-2 Study.

PubMed

Salinero-Fort, M A; Burgos-Lunar, C; Lahoz, C; Mostaza, J M; Abánades-Herranz, J C; Laguna-Cuesta, F; Estirado-de Cabo, E; García-Iglesias, F; González-Alegre, T; Fernández-Puntero, B; Montesano-Sánchez, L; Vicent-López, D; Cornejo-Del Río, V; Fernández-García, P J; Sánchez-Arroyo, V; Sabín-Rodríguez, C; López-López, S; Patrón-Barandio, P; Gómez-Campelo, P

2016-01-01

To evaluate the performance of the Finnish Diabetes Risk Score (FINDRISC) and a simplified FINDRISC score (MADRISC) in screening for undiagnosed type 2 diabetes mellitus (UT2DM) and dysglycaemia. A population-based, cross-sectional, descriptive study was carried out with participants with UT2DM, ranged between 45-74 years and lived in two districts in the north of metropolitan Madrid (Spain). The FINDRISC and MADRISC scores were evaluated using the area under the receiver operating characteristic curve method (ROC-AUC). Four different gold standards were used for UT2DM and any dysglycaemia, as follows: fasting plasma glucose (FPG), oral glucose tolerance test (OGTT), HbA1c, and OGTT or HbA1c. Dysglycaemia and UT2DM were defined according to American Diabetes Association criteria. The study population comprised 1,426 participants (832 females and 594 males) with a mean age of 62 years (SD = 6.1). When HbA1c or OGTT criteria were used, the prevalence of UT2DM was 7.4% (10.4% in men and 5.2% in women; p<0.01) and the FINDRISC ROC-AUC for UT2DM was 0.72 (95% CI, 0.69-0.74). The optimal cut-off point was ≥13 (sensitivity = 63.8%, specificity = 65.1%). The ROC-AUC of MADRISC was 0.76 (95% CI, 0.72-0.81) with ≥13 as the optimal cut-off point (sensitivity = 84.8%, specificity = 54.6%). FINDRISC score ≥12 for detecting any dysglycaemia offered the best cut-off point when HbA1c alone or OGTT and HbA1c were the criteria used. FINDRISC proved to be a useful instrument in screening for dysglycaemia and UT2DM. In the screening of UT2DM, the simplified MADRISC performed as well as FINDRISC.

Cluster Observations of Particle Injections in the Exterior Cusp

NASA Astrophysics Data System (ADS)

Escoubet, C. P.; Grison, B.; Berchem, J.; Trattner, K. J.; Lavraud, B.; Pitout, F.; Soucek, J.; Richard, R. L.; Laakso, H. E.; Masson, A.; Dunlop, M. W.; Dandouras, I. S.; Reme, H.; Fazakerley, A. N.; Daly, P. W.

2014-12-01

The main process that injects solar wind plasma into the polar cusp is now generally accepted to be magnetic reconnection. Depending on the IMF direction, this process takes place equatorward (for IMF southward), poleward (for IMF northward) or on the dusk or dawn sides (for IMF azimuthal) of the cusp. We report a Cluster crossing on 5 January 2002 near the exterior cusp on the southern dusk side. The IMF was mainly azimuthal (IMF-By around -5 nT), the solar wind speed lower than usual around 280 km/s with the density of order 5 cm-3. The four Cluster spacecraft had an elongated configuration near the magnetopause. C4 was the first spacecraft to enter the cusp around 19:52:04 UT, followed by C2 at 19:52:35 UT, C1 at 19:54:24 UT and C3 at 20:13:15 UT. C4 and C1 observed two ion energy dispersions at 20:10 UT and 20:40 UT and C3 at 20:35 UT and 21:15 UT. Using the time of flight technique on the upgoing and downgoing ions, which leads to energy dispersions, we obtain distances of the ion sources between 14 and 20 RE from the spacecraft. Using Tsyganenko model, we find that these sources are located on the dusk flank, past the terminator. The first injection by C3 is seen at approximately the same time as the 2nd injection on C1 but their sources at the magnetopause were separated by more than 7 RE. This would imply that two distinct sources were active at the same time on the dusk flank of the magnetosphere. In addition, a flow reversal was observed at the magnetopause on C4 which would be an indication that reconnection is taking place near the exterior cusp.

Microstructure and Mechanical Properties of Dissimilar Joints of Al-Mg2Si and 5052 Aluminum Alloy by Friction Stir Welding

NASA Astrophysics Data System (ADS)

Huang, B. W.; Qin, Q. D.; Zhang, D. H.; Wu, Y. J.; Su, X. D.

2018-03-01

Al-Mg2Si alloy and 5052 Al alloy were welded successfully by friction stir welding (FSW) in this study. The results show that the alloy consists of three distinct zones after FSW: the base material zone (BMZ), the transitional zone, and the weld nugget (WN). The morphologies of the primary Mg2Si phases are identified as coarse equiaxed crystals for Al-Mg2Si alloys in the BMZ. The WN is a mixture of rich Al-Mg2Si and rich 5052 alloy, and a banded structure is formed in the zone. Interestingly, in the WN, the equiaxed crystals changed to polygonal particles with substantially reduced sizes in the rich Al-Mg2Si zone. However, in addition to the white rich Mg phase appearing in the rich 5052 zone near the interface, the 5052 alloy does not show obvious changes. The hardness gradually increases from the BMZ of the 5052 to the welded joint to the Al-Mg2Si BMZ. In addition, the ultimate tensile strength (UTS) of the welded joint is higher than that of the base material of the Al-Mg2Si, whereas it is lower than that of the 5052 base alloy. The results of the elongation are similar to the UTS results. The fracture mechanism is also investigated.

Effect of photoactivated riboflavin on the biodegradation-resistance of root-dentin collagen.

PubMed

Priyadarshini, Balasankar Meera; Lu, Thong Beng; Fawzy, Amr S

2017-12-01

This study was conducted to evaluate the effect of UVA-activated 1% riboflavin solution on structural integrity; mechanical properties and stability; and collagenase-mediated collagen solubilisation resistance of demineralized root dentin collagen matrix. Root dentin specimens demineralized with 17% EDTA for 7days were treated with 1% RF for 1min followed by UVA photo-activation at intensity 7mW/cm 2 for 1min. Control specimens were completely devoid of riboflavin and/or UVA treatments. Specimens were challenged with bacterial collagenase type-I solution for different time-periods at 37°C. Collagen solubilisation resistance was evaluated in terms of hydroxyproline (HYP) liberation. Mechanical characterization of dentin specimens before and after 24h of exposure to collagenase solution was done in terms of apparent-elastic modulus (E appr ) and ultimate tensile strength (UTS). Variations in dentin collagen-network structure with exposure time in collagenase were visualized by TEM. Crosslinking dentin with UVA-activated riboflavin significantly decreased HYP release and increased E appr and UTS compared to control specimens with storage time in collagenase. Moreover, crosslinked specimens showed higher structural resistance to collagenase effect reflected from dense, well-formed collagen fibrils-network with characteristic collagen cross-banding. UVA-activated riboflavin treatment increased collagenase-mediated collagen degradation resistance and enhanced mechanical stability against collagenase challenges of root dentin after EDTA demineralization. Copyright © 2017 Elsevier B.V. All rights reserved.

Incorporation of composite defects from ultrasonic NDE into CAD and FE models

NASA Astrophysics Data System (ADS)

Bingol, Onur Rauf; Schiefelbein, Bryan; Grandin, Robert J.; Holland, Stephen D.; Krishnamurthy, Adarsh

2017-02-01

Fiber-reinforced composites are widely used in aerospace industry due to their combined properties of high strength and low weight. However, owing to their complex structure, it is difficult to assess the impact of manufacturing defects and service damage on their residual life. While, ultrasonic testing (UT) is the preferred NDE method to identify the presence of defects in composites, there are no reasonable ways to model the damage and evaluate the structural integrity of composites. We have developed an automated framework to incorporate flaws and known composite damage automatically into a finite element analysis (FEA) model of composites, ultimately aiding in accessing the residual life of composites and make informed decisions regarding repairs. The framework can be used to generate a layer-by-layer 3D structural CAD model of the composite laminates replicating their manufacturing process. Outlines of structural defects, such as delaminations, are automatically detected from UT of the laminate and are incorporated into the CAD model between the appropriate layers. In addition, the framework allows for direct structural analysis of the resulting 3D CAD models with defects by automatically applying the appropriate boundary conditions. In this paper, we show a working proof-of-concept for the composite model builder with capabilities of incorporating delaminations between laminate layers and automatically preparing the CAD model for structural analysis using a FEA software.

Infrared observations of an outburst of small dust grains from the nucleus of Comet P/Halley 1986 III at perihelion

NASA Technical Reports Server (NTRS)

Gehrz, R. D.; Johnson, C. H.; Magnuson, S. D.; Ney, E. P.; Hayward, T. L.

1995-01-01

A close examination of the 0.7- to 23-micron infrared data base acquired by Gehrz and Ney (1992), suggests that the nucleus of Comet P/Halley 1986 III emitted a burst of small dust grains during a 3-day period commencing within hours of perihelion passage on 1986 February 9.46 UT. The outburst was characterized by significant increases in the coma's grain color temperature T(sub obs), temperature excess (superheat: S = T(sub obs)/T(sub BB)), infrared luminosity, albedo, and 10-micron silicate emission feature strength. These changes are all consistent with the sudden ejection from the nucleus of a cloud of grains with radii of approximately 0.5 micron. This outburst may have produced the dust that was responsible for some of the tail streamers photographed on 1986 February 22 UT. The peak of the dust outburst occurred about 3 days before a pronounced increase in the water production rate measured by the Pioneer Venus Orbiter Ultraviolet Spectrometer. We suggest that jets that release large quantities of small particles may be largely responsible for some of the variable infrared behavior that has been reported for P/Halley and other comets during the past two decades. Such jets may also account for some of the differences IR Type I and IR Type II comets.

First simultaneous measurements of waves generated at the bow shock in the solar wind, the magnetosphere and on the ground

NASA Astrophysics Data System (ADS)

Clausen, L. B. N.; Yeoman, T. K.; Fear, R. C.; Behlke, R.; Lucek, E. A.; Engebretson, M. J.

2009-01-01

On 5 September 2002 the Geotail satellite observed the cone angle of the Interplanetary Magnetic Field (IMF) change to values below 30° during a 56 min interval between 18:14 and 19:10 UT. This triggered the generation of upstream waves at the bow shock, 13 RE downstream of the position of Geotail. Upstream generated waves were subsequently observed by Geotail between 18:30 and 18:48 UT, during times the IMF cone angle dropped below values of 10°. At 18:24 UT all four Cluster satellites simultaneously observed a sudden increase in wave power in all three magnetic field components, independent of their position in the dayside magnetosphere. We show that the 10 min delay between the change in IMF direction as observed by Geotail and the increase in wave power observed by Cluster is consistent with the propagation of the IMF change from the Geotail position to the bow shock and the propagation of the generated waves through the bow shock, magnetosheath and magnetosphere towards the position of the Cluster satellites. We go on to show that the wave power recorded by the Cluster satellites in the component containing the poloidal and compressional pulsations was broadband and unstructured; the power in the component containing toroidal oscillations was structured and shows the existence of multi-harmonic Alfvénic continuum waves on field lines. Model predictions of these frequencies fit well with the observations. An increase in wave power associated with the change in IMF direction was also registered by ground based magnetometers which were magnetically conjunct with the Cluster satellites during the event. To the best of our knowledge we present the first simultaneous observations of waves created by backstreaming ions at the bow shock in the solar wind, the dayside magnetosphere and on the ground.

Local regularity for time-dependent tug-of-war games with varying probabilities

NASA Astrophysics Data System (ADS)

Parviainen, Mikko; Ruosteenoja, Eero

2016-07-01

We study local regularity properties of value functions of time-dependent tug-of-war games. For games with constant probabilities we get local Lipschitz continuity. For more general games with probabilities depending on space and time we obtain Hölder and Harnack estimates. The games have a connection to the normalized p (x , t)-parabolic equation ut = Δu + (p (x , t) - 2) Δ∞N u.

The liquidus temperature of nuclear waste glasses: an international Round-Robin Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Riley, Brian J.; Hrma, Pavel R.; Vienna, John D.

2012-12-01

Ten institutions from five countries participated in a Round Robin study to contribute to the Precision and Bias section of an American Society for Testing and Materials standard procedure that Pacific Northwest National Laboratory (PNNL) is developing for measuring the liquidus temperature (TL) of radioactive and simulated waste glasses. In this study, three separate TL measurement methods were a gradient temperature (GT) method, a uniform temperature (UT) method, and a crystal fraction extrapolation (CF) method. Three different glasses were measured with a combination of these three methods. The TL values reported by different institutions are generally consistent and vary withinmore » a narrow range. The precision of a TL measurement was evaluated as ±10°C regardless of the method used for making the measurement. The Round Robin glasses were all previously studied at PNNL and included ARG-1 (Glass A), Zr-9 (Glass B), and AmCm2-19 (Glass C), with measured TL values spanning the temperature range ~960-1240°C. The three methods discussed here in more detail are the GT, UT, and CF methods. A best-case precision for TL has been obtained from the data, even though the data were not acquired for all three glasses using all three methods from each participating organization.« less

Elevated temperature mechanical properties of line pipe steels

NASA Astrophysics Data System (ADS)

Jacobs, Taylor Roth

The effects of test temperature on the tensile properties of four line pipe steels were evaluated. The four materials include a ferrite-pearlite line pipe steel with a yield strength specification of 359 MPa (52 ksi) and three 485 MPa (70 ksi) yield strength acicular ferrite line pipe steels. Deformation behavior, ductility, strength, strain hardening rate, strain rate sensitivity, and fracture behavior were characterized at room temperature and in the temperature range of 200--350 °C, the potential operating range for steels used in oil production by the steam assisted gravity drainage process. Elevated temperature tensile testing was conducted on commercially produced as-received plates at engineering strain rates of 1.67 x 10 -4, 8.33 x 10-4, and 1.67 x 10-3 s-1. The acicular ferrite (X70) line pipe steels were also tested at elevated temperatures after aging at 200, 275, and 350 °C for 100 h under a tensile load of 419 MPa. The presence of serrated yielding depended on temperature and strain rate, and the upper bound of the temperature range where serrated yielding was observed was independent of microstructure between the ferrite-pearlite (X52) steel and the X70 steels. Serrated yielding was observed at intermediate temperatures and continuous plastic deformation was observed at room temperature and high temperatures. All steels exhibited a minimum in ductility as a function of temperature at testing conditions where serrated yielding was observed. At the higher temperatures (>275 °C) the X52 steel exhibited an increase in ductility with an increase in temperature and the X70 steels exhibited a maximum in ductility as a function of temperature. All steels exhibited a maximum in flow strength and average strain hardening rate as a function of temperature. The X52 steel exhibited maxima in flow strength and average strain hardening rate at lower temperatures than observed for the X70 steels. For all steels, the temperature where the maximum in both flow strength and strain hardening occurred increased with increasing strain rate. Strain rate sensitivities were measured using flow stress data from multiple tensile tests and strain rate jump tests on single tensile samples. In flow stress strain rate sensitivity measurements, a transition from negative to positive strain rate sensitivity was observed in the X52 steel at approximately 275--300 °C, and negative strain rate sensitivity was observed at all elevated temperature testing conditions in the X70 steels. In jump test strain rate sensitivity measurements, all four steels exhibited a transition from negative to positive strain rate sensitivity at approximately 250--275 °C. Anisotropic deformation in the X70 steels was observed by measuring the geometry of the fracture surfaces of the tensile samples. The degree of anisotropy changed as a function of temperature and minima in the degree of anisotropy was observed at approximately 300 °C for all three X70 steels. DSA was verified as an active strengthening mechanism at elevated temperatures for all line pipe steels tested resulting in serrated yielding, a minimum in ductility as a function of temperature, a maximum in flow strength as a function of temperature, a maximum in average strain hardening rate as a function of temperature, and negative strain rate sensitivities. Mechanical properties of the X70 steels exhibited different functionality with respect to temperature compared to the X52 steels at temperatures greater than 250 ºC. Changes in the acicular ferrite microstructure during deformation such as precipitate coarsening, dynamic precipitation, tempering of martensite in martensite-austenite islands, or transformation of retained austenite could account for differences in tensile property functionality between the X52 and X70 steels. Long term aging under load (LTA) testing of the X70 steels resulted in increased yield strength compared to standard elevated temperature tensile tests at all temperatures as a result of static strain aging. LTA specimen ultimate tensile strengths (UTS) increased slightly at 200 °C, were comparable at 275 °C, and decreased significantly at 350 °C when compared to as-received (standard) tests at 350 °C. Observed reductions in UTS were a result of decreased strain hardening in the LTA specimens compared to standard tensile specimens. Ideal elevated temperature operating conditions (based on tensile properties) for the X70 line pipe steels in the temperature range relevant to the steam assisted gravity drainage process are around 275--325 °C at the strain rates tested. In the temperature range of 275--325 °C the X70 steels exhibited continuous plastic deformation, a maximum in ductility, a maximum in flow stress, improved strain hardening compared to intermediate temperatures, reduced anisotropic deformation, and after extended use at elevated temperatures, yield strength increases with little change in UTS.

Turbulent flame propagation and combustion in spark ignition engines

NASA Technical Reports Server (NTRS)

Beretta, G. P.; Rashidi, M.; Keck, J. C.

1983-01-01

Pressure measurements synchronized with high-speed motion-picture records of flame propagation have been made in a transparent-piston engine. The data show that the initial expansion speed of the flame front is close to that of a laminar flame. As the flame expands, its speed rapidly accelerates to a quasi-steady value comparable with that of the turbulent velocity fluctuations in the unburned gas. During the quasi-steady propagation phase, a significant fraction of the gas behind the visible front is unburned. Final burnout of the charge may be approximated by an exponential decay in time. The data have been analyzed in a model-independent way to obtain a set of empirical equations for calculating mass burning rates in spark-ignition engines. The burning equations contain three parameters: the laminar burning speed, a characteristic speed (uT), and a characteristic length (lT). The laminar burning speed is known from laboratory measurements. Tentative correlations relating uT and lT to engine geometry and operating variables have been derived from the engine data.

Mechanical properties of aluminium fused SiO2 particulate composites cast using metallic and non-metallic chills

NASA Astrophysics Data System (ADS)

Harshith, H. S.; Hemanth, Joel

2018-04-01

This research work aims at developing and mechanical characterization of aluminium (LM13) based metal matrix composite reinforced with varying percentage of fused SiO2 (3%,6%,9%,12%). The mechanical properties are completely dependent on the microstructural parameters of the system. Also the microstructure further depends on the cooling rates during solidification process. Various Chills like Silicon carbide, Mild steel, Copper were used during the casting process to increase the rate of solidification, which enhances the mechanical properties of the composite. The chill casted specimens were subjected to tensile and hardness tests followed by microstructure studies. A casting produced using mild steel chill exhibited higher young's modulus and was found to be maximum at 9% reinforcement. Finer microstructure and better UTS were seen for specimen's casted using copper chills, whereas silicon carbide and mild steel chills gave rise to very coarse structure with reduced UTS values compared to copper chills.

Energy decay of a viscoelastic wave equation with supercritical nonlinearities

NASA Astrophysics Data System (ADS)

Guo, Yanqiu; Rammaha, Mohammad A.; Sakuntasathien, Sawanya

2018-06-01

This paper presents a study of the asymptotic behavior of the solutions for the history value problem of a viscoelastic wave equation which features a fading memory term as well as a supercritical source term and a frictional damping term: u_{tt}- k(0) Δ u - \\int \\limits _0^{&infty } k'(s) Δ u(t-s) ds +|u_t|^{m-1}u_t =|u|^{p-1}u, { in } Ω × (0,T), u(x,t)=u_0(x,t), \\quad { in } Ω × (-∞,0]), where Ω is a bounded domain in R^3 with a Dirichlét boundary condition and u_0 represents the history value. A suitable notion of a potential well is introduced for the system, and global existence of solutions is justified, provided that the history value u_0 is taken from a subset of the potential well. Also, uniform energy decay rate is obtained which depends on the relaxation kernel -k'(s) as well as the growth rate of the damping term. This manuscript complements our previous work (Guo et al. in J Differ Equ 257:3778-3812, 2014, J Differ Equ 262:1956-1979, 2017) where Hadamard well-posedness and the singularity formulation have been studied for the system. It is worth stressing the special features of the model, namely the source term here has a supercritical growth rate and the memory term accounts to the full past history that goes back to -∞.

A review on mechanical properties of magnesium based nano composites

NASA Astrophysics Data System (ADS)

Tarafder, Nilanjan; Prasad, M. Lakshmi Vara

2018-04-01

A review was done on Magnesium (Mg) based composite materials reinforced with different nano particles such as TiO2, Cu, Y2O3, SiC, ZrO2 and Al2O3. TiO2 and Al2O3 nanoparticles were synthesised by melt deposition process. Cu, Y2O3, SiC and ZrO2 nanoparticles were synthesised by powder metallurgy process. Composite microstructural characteristics shows that the nano-size reinforcements are uniformly distributed in the composite matrix and also minimum porosity with solid interfacial integrity. The mechanical properties showed yield strength improvement by 0.2 percentage and Ultimate tensile strength (UTS) was also improved for all the nano-particles. But UTS was adversely affected with TiO2 reinforcement while ductility was increased. With Cu reinforcement elastic modulus, hardness and fracture resistance increased and improved the co-efficient of thermal expansion (CTE) of Mg based matrix. By Y2O3 reinforcement hardness, fracture resistance was improved and ductility reached maximum by 0.22 volume percentage of Y2O3 and decreased with succeeding increase in Y2O3 reinforcement. The readings exposed that mechanical properties were gathered from the composite comprising 2.0 weight percentage of Y2O3. Ductility and fracture resistance increased with ZrO2 reinforcement in Mg matrix. Using Al2O3 as reinforcement in Mg composite matrix hardness, elastic modulus and ductility was increased but porosity reduced with well interfacial integrity. Dissipation of energy in the form of damping capacity was resolved by classical vibration theory. The result showed that an increasing up to 0.4 volume percentage alumina content increases the damping capacity up to 34 percent. In another sample, addition of 2 weight percentage nano-Al2O3 particles showed big possibility in reducing CTE from 27.9-25.9×10-6 K-1 in Magnesium, tensile and yield strength amplified by 40MPa. In another test, Mg/1.1Al2O3 nanocomposite was manufactured by solidification process followed by hot extrusion. Results showed that strengthening effect was maintained up to 150°C and fracture characteristics of Mg composite transformed from brittle to mixed ductile mode and fully ductile in attendance of nano-Al2O3 particulates.

On the initial-boundary value problem for some quasilinear parabolic equations of divergence form

NASA Astrophysics Data System (ADS)

Nakao, Mitsuhiro

2017-12-01

In this paper we give an existence theorem of global classical solution to the initial boundary value problem for the quasilinear parabolic equations of divergence form ut -div { σ (| ∇u|2) ∇u } = f (∇u , u , x , t) where σ (| ∇u|2) may not be bounded as | ∇u | → ∞. As an application the logarithmic type nonlinearity σ (| ∇u|2) = log ⁡ (1 + | ∇u|2) which is growing as | ∇u | → ∞ and degenerate at | ∇u | = 0 is considered under f ≡ 0.

A Review of Methods for Moving Boundary Problems

DTIC Science & Technology

2009-07-01

the bound- ary value problem for the eikonal equation: ‖∇u‖ = 1 for x ∈ Ω (29) u = 0 for x ∈ Γ (30) ERDC/CHL TR-09-10 8 where ‖ ‖ is the Euclidean norm...Solutions of the eikonal equation can in turn be characterized as steady state solutions of the initial value prob- lem ut + sgn(u0)(‖∇u‖ − 1) = 0...LS using the eikonal equation and use the NCI equation for the LS dynam- ics. The complete system of equations in weak form is ∫ Ω (‖∇u‖ − 1)wdV = 0

Effect of Continuous Galvanizing Heat Treatments on the Microstructure and Mechanical Properties of High Al-Low Si Transformation Induced Plasticity Steels

NASA Astrophysics Data System (ADS)

Bellhouse, E. M.; McDermid, J. R.

2010-02-01

Heat treatments were performed using an isothermal bainitic transformation (IBT) temperature compatible with continuous hot-dip galvanizing on two high Al-low Si transformation induced plasticity (TRIP)-assisted steels. Both steels had 0.2 wt pct C and 1.5 wt pct Mn; one had 1.5 wt pct Al and the other had 1 wt pct Al and 0.5 wt pct Si. Two different intercritical annealing (IA) temperatures were used, resulting in intercritical microstructures of 50 pct ferrite (α)-50 pct austenite (γ) and 65 pct α-35 pct γ. Using the IBT temperature of 465 °C, five IBT times were tested: 4, 30, 60, 90, and 120 seconds. Increasing the IBT time resulted in a decrease in the ultimate tensile strength (UTS) and an increase in the uniform elongation, yield strength, and yield point elongation. The uniform elongation was higher when using the 50 pct α-50 pct γ IA temperature when compared to the 65 pct α-35 pct γ IA temperature. The best combinations of strength and ductility and their corresponding heat treatments were as follows: a tensile strength of 895 MPa and uniform elongation of 0.26 for the 1.5 pct Al TRIP steel at the 50 pct γ IA temperature and 90-second IBT time; a tensile strength of 880 MPa and uniform elongation of 0.27 for the 1.5 pct Al TRIP steel at the 50 pct γ IA temperature and 120-second IBT time; and a tensile strength of 1009 MPa and uniform elongation of 0.22 for the 1 pct Al-0.5 pct Si TRIP steel at the 50 pct γ IA temperature and 120-second IBT time.

VizieR Online Data Catalog: Sloan i follow-up light curves of HATS-18 (Penev+, 2016)

NASA Astrophysics Data System (ADS)

Penev, K.; Hartman, J. D.; Bakos, G. A.; Ciceri, S.; Brahm, R.; Bayliss, D.; Bento, J.; Jordan, A.; Csubry, Z.; Bhatti, W.; de Val-Borro, M.; Espinoza, N.; Zhou, G.; Mancini, L.; Rabus, M.; Suc, V.; Henning, T.; Schmidt, B.; Noyes, R. W.; Lazar, J.; Papp, I.; Sari, P.

2017-02-01

The star HATS-18 was observed by HATSouth instruments between UT 2011 April 18 and UT 2013 July 21 using the HS-2, HS-4, and HS-6 units at the Las Campanas Observatory in Chile, the High Energy Spectroscopic Survey (H.E.S.S.) site in Namibia, and Siding Spring Observatory (SSO) in Australia, respectively. A total of 5372, 3758, and 4008 images of HATS-18 were obtained with HS-2, HS-4, and HS-6, respectively. The observations were obtained through a Sloan r filter with an exposure time of 240s. We obtained follow-up light curves of HATS-18 using the Las Cumbres Observatory Global Telescope (LCOGT) 1m telescope network. An ingress was observed on UT 2015 July 18 with the SBIG camera and a Sloan i filter on the 1m at the South African Astronomical Observatory (SAAO). A total of 33 images were collected at a median cadence of 201s. A full transit was observed on UT 2016 January 22 with the sinistro camera and a Sloan i filter on the 1m at Cerro Tololo Inter-American Observatory. A total of 61 images were collected at a median cadence of 219s. For the record, we also note that a full transit was observed on UT 2016 January 3 with the SBIG camera on the 1m at SAAO; however, due to tracking and weather problems, we were unable to extract high-precision photometry from these images, and therefore do not include these data in our analysis. The data are available in Table1. Spectroscopic follow-up observations of HATS-18 were carried out with WiFeS on the Australian National University (ANU) 2.3m telescope and with the Fiber-fed Extended Range Optical Spectrograph (FEROS) on the MPG 2.2m. A total of three spectra were obtained with WiFeS between UT 2015 February 28 and UT 2015 March 2, two at a resolution of R=Δλ/λ=7000, and one at R=3000. We obtained six R=48000 spectra with FEROS between UT 2015 June 12 and UT 2015 June 20. The data are provided in Table2. (2 data files).

In-Plane Anisotropy in Mechanical Behavior and Microstructural Evolution of Commercially Pure Titanium in Tensile and Cyclic Loading

NASA Astrophysics Data System (ADS)

Sinha, Subhasis; Gurao, N. P.

2017-12-01

Tensile and cyclic deformation behavior of three samples oriented at 0, 45, and 90 deg to the rolling direction in the rolling direction-transverse direction (RD-TD) plane of cold-rolled and annealed plate of commercially pure titanium is studied in the present investigation. The sample along the RD (R0) shows the highest strength but lowest ductility in monotonic tension. Although ultimate tensile strength (UTS) and elongation of samples along 45 and 90 deg to the RD (R45 and R90, respectively) are similar, the former has significantly higher yield strength than the latter, indicating different strain-hardening behavior. It is found that the R90 sample exhibits the highest monotonic ductility as well as fatigue life. This is attributed to a higher propensity for twinning in this sample with the presence of multiple variants and twin intersections. Cyclic life is also influenced by the high tendency for detwinning of contraction twins in this orientation. Elastoplastic self-consistent (EPSC) simulations of one-cycle tension-compression load reversal indicate that the activity of pyramidal 〈 c + a〉 slip and extension twinning oscillates during cyclic loading that builds up damage in a cumulative manner, leading to failure in fatigue.

The InterCon network: a program for education partnerships at the University of Texas-Houston Health Science Center.

PubMed

Castro, G A; Bouldin, P A; Farver, D W; Maugans, L A; Sanders, L C; Booker, J

1999-04-01

The University of Texas-Houston Health Science Center (UT-Houston) has created programs and activities to address the state's pressing needs in minority education. Through InterCon, a network of universities and K-12 schools, UT-Houston works with its partners to identify competitive candidates in the current pool of minority graduates with bachelor's degrees and to help them--along with their non-minority counterparts--progress in their education. Another objective is to expand the pool of minorities underrepresented in medicine who complete high school and go to college. In 1994 UT-Houston and Prairie View A&M University created a collaborative venture to provide new educational opportunities at UT-Houston for Prairie View's predominantly African American students. A three-track summer internship program--a result of that collaboration--has since been expanded to partnerships with other minority and majority universities throughout Texas. In 1998, for example, 108 undergraduate students from these universities (and 40 other universities nationwide) participated in research, professional, and administrative summer internships at UT-Houston. The InterCon network also has partnerships with K-12 schools. UT-Houston works with inner-city, suburban, and rural school districts to develop education models that can be transferred throughout the state. The partnerships deal with helping to teach basic academic skills and computer literacy, improve science-related instruction, meet demands for health promotion materials and information for school-initiated health and wellness programs, and develop distance-learning paradigms. UT-Houston views InterCon as a program helping Texas institutions to engage and adapt to the socioeconomic factors, demographic changes, and technology explosion that currently challenge public education.

Distribution of extracellular matrix molecules in human uterine tubes during the menstrual cycle: a histological and immunohistochemical analysis.

PubMed

Godoy-Guzmán, Carlos; Nuñez, Claudio; Orihuela, Pedro; Campos, Antonio; Carriel, Víctor

2018-04-16

The uterine tube (UT) is an important and complex organ of the women's reproductive system. In general, the anatomy and basic histology of this organ are well-known. However, the composition and function of the extracellular matrix (ECM) of the UT is still poorly understood. The ECM is a complex supramolecular material produced by cells which is commonly restricted to the basement membrane and interstitial spaces. ECM molecules play not only a structural role, they are also important for cell growth, survival and differentiation in all tissues. In this context, the aim of this study was to evaluate the deposition and distribution of type I and III collagens and proteoglycans (decorin, biglycan, fibromodulin and versican) in human UT during the follicular and luteal phases by using histochemical and immunohistochemical techniques. Our results showed a broad synthesis of collagens (I and III) in the stroma of the UT. The analysis by regions showed, in the mucosa, a specific distribution of versican and fibromodulin in the epithelial surface, whereas decorin and fibromodulin were observed in the lamina propria. Versican and decorin were found in the stroma of the muscular layer, whereas all studied proteoglycans were identified in the serosa. Curiously, biglycan was restricted to the wall of the blood vessels of the serosa and muscular layers. Furthermore, there was an immunoreaction for collagens, decorin, versican and fibromodulin in the UT peripheral nerves. The differential distribution of these ECM molecules in the different layers of the UT could be related to specific structural and/or biomechanical functions needed for the oviductal transport, successful fertilization and early embryogenesis. However, further molecular studies under physiological and pathological conditions are still needed to elucidate the specific role of each molecule in the human UT. © 2018 Anatomical Society.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bonner, H.W.; Buffington, C.K.; Leslie, S.W.

Following a 25 ..mu..Ci/kg i/p injection, /sup 45/Ca/sup + +/ activity from the mitochondria and fragmented sarcoplasmic reticulum (FSR) of the superficial rectus femoris (FG-fibers) and combined soleus muscle (SO-fibers) of trained (T, N = 9) and untrained (UT, N = 8) male Wistar rats was determined. The FG mitochondrial /sup 45/Ca/sup + +/ activity from rested animals was 3.9 (T) and 5.3 (UT) times greater than the FSR from this muscle group while the SO-mitochondrial /sup 45/Ca/sup + +/ activity was 13.2 (T) and 20.5 (UT) times greater when compared with the respective SO-FSR (p less than 0.01). Themore » mitochondrial /sup 45/Ca/sup + +/ content of the SO-fibers from rested animals was 58% UT, (p less than 0.01) and 148% (T, p less than 0.001) greater than that of the FG mitochondria. After 20 to 26 weeks of exercise training the SO-mitochondrial /sup 45/Ca/sup + +/ content of the rested-T animals was approximately 18% lower (p less than 0.05) while the T-FG-mitochondrial /sup 45/Ca/sup + +/ content was 48% less than that of UT animals (p less than 0.01) with a concomitant 28% greater /sup 45/Ca/sup + +/ activity in SO-FSR for the T-group as compared to UT (p less than 0.01). Following a rapidly exhaustive treadmill run the mitochondrial /sup 45/Ca/sup + +/ content in the UT group was depressed by 21% in SO-fibers and 37% in FG-fibers (p less than 0.01) with no changes occurring in the T-group. Exhaustion produced no significant changes in the /sup 45/Ca/sup + +/ activity of the FSR from either group of animals.« less

EEJ and EIA variations during modeling substorms with different onset moments

NASA Astrophysics Data System (ADS)

Klimenko, V. V.; Klimenko, M. V.

2015-11-01

This paper presents the simulations of four modeling substorms with different moment of substorm onset at 00:00 UT, 06:00 UT, 12:00 UT, and 18:00 UT for spring equinoctial conditions in solar activity minimum. Such investigation provides opportunity to examine the longitudinal dependence of ionospheric response to geomagnetic substorms. Model runs were performed using modified Global Self-consistent Model of the Thermosphere, Ionosphere and Protonosphere (GSM TIP). We analyzed GSM TIP simulated global distributions of foF2, low latitude electric field and ionospheric currents at geomagnetic equator and their disturbances at different UT moments substorms. We considered in more detail the variations in equatorial ionization anomaly, equatorial electrojet and counter equatorial electrojet during substorms. It is shown that: (1) the effects in EIA, EEJ and CEJ strongly depend on the substorm onset moment; (2) disturbances in equatorial zonal current density during substorm has significant longitudinal dependence; (3) the observed controversy on the equatorial ionospheric electric field signature of substorms can depend on the substorm onset moments, i.e., on the longitudinal variability in parameters of the thermosphere-ionosphere system.

A human pericardium biopolymeric scaffold for autologous heart valve tissue engineering: cellular and extracellular matrix structure and biomechanical properties in comparison with a normal aortic heart valve.

PubMed

Straka, Frantisek; Schornik, David; Masin, Jaroslav; Filova, Elena; Mirejovsky, Tomas; Burdikova, Zuzana; Svindrych, Zdenek; Chlup, Hynek; Horny, Lukas; Daniel, Matej; Machac, Jiri; Skibová, Jelena; Pirk, Jan; Bacakova, Lucie

2018-04-01

The objective of our study was to compare the cellular and extracellular matrix (ECM) structure and the biomechanical properties of human pericardium (HP) with the normal human aortic heart valve (NAV). HP tissues (from 12 patients) and NAV samples (from 5 patients) were harvested during heart surgery. The main cells in HP were pericardial interstitial cells, which are fibroblast-like cells of mesenchymal origin similar to the valvular interstitial cells in NAV tissue. The ECM of HP had a statistically significantly (p < 0.001) higher collagen I content, a lower collagen III and elastin content, and a similar glycosaminoglycans (GAGs) content, in comparison with the NAV, as measured by ECM integrated density. However, the relative thickness of the main load-bearing structures of the two tissues, the dense part of fibrous HP (49 ± 2%) and the lamina fibrosa of NAV (47 ± 4%), was similar. In both tissues, the secant elastic modulus (Es) was significantly lower in the transversal direction (p < 0.05) than in the longitudinal direction. This proved that both tissues were anisotropic. No statistically significant differences in UTS (ultimate tensile strength) values and in calculated bending stiffness values in the longitudinal or transversal direction were found between HP and NAV. Our study confirms that HP has an advantageous ECM biopolymeric structure and has the biomechanical properties required for a tissue from which an autologous heart valve replacement may be constructed.

Defense Waste Processing Facility Canister Closure Weld Current Validation Testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Korinko, P. S.; Maxwell, D. N.

Two closure welds on filled Defense Waste Processing Facility (DWPF) canisters failed to be within the acceptance criteria in the DWPF operating procedure SW4-15.80-2.3 (1). In one case, the weld heat setting was inadvertently provided to the canister at the value used for test welds (i.e., 72%) and this oversight produced a weld at a current of nominally 210 kA compared to the operating procedure range (i.e., 82%) of 240 kA to 263 kA. The second weld appeared to experience an instrumentation and data acquisition upset. The current for this weld was reported as 191 kA. Review of the datamore » from the Data Acquisition System (DAS) indicated that three of the four current legs were reading the expected values, approximately 62 kA each, and the fourth leg read zero current. Since there is no feasible way by further examination of the process data to ascertain if this weld was actually welded at either the target current or the lower current, a test plan was executed to provide assurance that these Nonconforming Welds (NCWs) meet the requirements for strength and leak tightness. Acceptance of the welds is based on evaluation of Test Nozzle Welds (TNW) made specifically for comparison. The TNW were nondestructively and destructively evaluated for plug height, heat tint, ultrasonic testing (UT) for bond length and ultrasonic volumetric examination for weld defects, burst pressure, fractography, and metallography. The testing was conducted in agreement with a Task Technical and Quality Assurance Plan (TTQAP) (2) and applicable procedures.« less

VizieR Online Data Catalog: Venus mesosphere ALMA observations (Piccialli+, 2017)

NASA Astrophysics Data System (ADS)

Piccialli, A.; Moreno, R.; Encrenaz, T.; Fouchet, T.; Lellouch, E.; Widemann, T.

2017-07-01

Observations of Venus were obtained using the ALMA interferometer within the project labeled 2011.0.00136.S. We observed - with a single receiver tuning setup - the CO, SO, SO2 and H2O rotational lines at frequencies of 345.795GHz, 346.528GHz, 346.652GHz and 335.395GHz, respectively. The spectral resolution (originally 61kHz) was binned to 0.35MHz in order to optimize the S/N. These observations were obtained on November 14, 2011, between 22:15 and 22:53 UT; on November 15, 2011, between 20:39 and 21:11 UT; on November 26, 2011, between 21:24 and 22:02 UT; and on November 27, 2011, between 21:07 and 21:58 UT. (23 data files).

Effect of protein supplementation on expression and distribution of urea transporter-B in lambs fed low-quality forage.

PubMed

Ludden, P A; Stohrer, R M; Austin, K J; Atkinson, R L; Belden, E L; Harlow, H J

2009-04-01

Two experiments were conducted to determine the effects of ruminal protein degradability, supplementation frequency, and increasing dietary protein on the expression and distribution of urea transporter-B (UT-B) in lambs fed low-quality forage (mature crested wheatgrass hay; 4.2 to 4.7% CP). In Exp. 1, 15 Dorset wether lambs (initial BW=45.8+/-1.3 kg) were blocked by initial BW and assigned to 1 of 3 treatments within a randomized complete block design for 28 d, with supplements fed to achieve 7, 10, or 13% total dietary CP. In Exp. 2, 13 Dorset wether lambs (initial BW=34+/-4 kg) were used in a completely randomized design and given 1 of 4 isonitrogenous supplements: 1) ruminally degradable protein (RDP) fed daily (n=3), 2) RDP fed on alternate days (n=3), 3) ruminally undegradable protein (RUP) fed on alternate days (n=3), or 4) a 50:50 mixture of RDP and RUP fed on alternate days (n=4) for 18 d. Alternate-day treatments were fed at twice that of daily supplementation. On the last day of both experiments, lambs were killed and samples taken for Western blot analyses for UT-B. Immunoblotting using a rabbit polyclonal antibody to UT-B confirmed the presence of distinct 32-kDa (consistent with a nonglycosylated UT-B protein) and 47-kDa (probable N-glycosylated form of UT-B) protein bands in all 9 tissues analyzed. In both experiments, the liver, dorsal rumen, reticulum, and ventral rumen displayed strong bands at 32 kDa and lighter bands at 47 kDa, whereas the cecum, large colon, spiral colon, and parotid salivary gland displayed slight 32-kDa bands and stronger, more visible bands at 47 kDa. Both protein bands were apparent in the kidney at similar visual intensities in Exp. 1, whereas the relative intensities of the 2 UT-B bands in the kidney were variable, and appeared somewhat reciprocal among animals in Exp. 2. Although the abundance of the 47-kDa UT-B band in the ventral rumen was greater (P=0.03) in lambs fed RDP daily in Exp. 2, no other treatment differences (P >or= 0.15 to 0.99) in the abundance of the 32- or 47-kDa UT-B proteins within tissues were observed in either experiment. Although protein supplementation strategy had little effect on UT-B expression in tissues other than the ventral rumen, differences in the degree of glycosylation of UT-B across tissues may provide insight into its regulation.

Estimation of ring tensile properties of steam oxidized Zircaloy-4 fuel cladding under simulated LOCA condition

NASA Astrophysics Data System (ADS)

Shriwastaw, R. S.; Sawarn, Tapan K.; Banerjee, Suparna; Rath, B. N.; Dubey, J. S.; Kumar, Sunil; Singh, J. L.; Bhasin, Vivek

2017-09-01

The present study involves the estimation of ring tensile properties of Indian Pressurised Heavy Water Reactor (IPHWR) fuel cladding made of Zircaloy-4, subjected to experiments under a simulated loss-of-coolant-accident (LOCA) condition. Isothermal steam oxidation experiments were conducted on clad tube specimens at temperatures ranging from 900 to 1200 °C at an interval of 50 °C for different soaking periods with subsequent quenching in water at ambient temperature. The specimens, which survived quenching, were then subjected to ambient temperature ring tension test (RTT). The microstructure was correlated with the mechanical properties. The yield strength (YS) and ultimate tensile strength (UTS) increased initially with rise in oxidation temperature and time duration but then decreased with further increase in oxidation. Ductility is adversely affected with rising oxidation temperature and longer holding time. A higher fraction of load bearing phase and lower oxygen content in it ensures higher residual ductility. Cladding shows almost zero ductility behavior in RIT when load bearing phase fraction is less than 0.72 and its average oxygen concentration is greater than 0.58 wt%.

Effect of ferrite transformation on the tensile and stress corrosion properties of type 316 L stainless steel weld metal thermally aged at 873 K

NASA Astrophysics Data System (ADS)

Shaikh, H.; Khatak, H. S.; Seshadri, S. K.; Gnanamoorthy, J. B.; Rodriguez, P.

1995-07-01

This article deals with the effect of the microstructural changes, due to transformation of delta ferrite, on the associated variations that take place in the tensile and stress corrosion properties of type 316 L stainless steel weld deposits when subjected to postweld heat treatment at 873 K for prolonged periods (up to 2000 hours). On aging for short durations (up to 20 hours), carbide/ carbonitride was the dominant transformation product, whereas sigma phase was dominant at longer aging times. The changes in the tensile and stress corrosion behavior of the aged weld metal have been attributed to the two competitive processes of matrix softening and hardening. Yield strength (YS) was found to depend predominantly on matrix softening only, while sig-nificant changes in the ultimate tensile strength (UTS) and the work-hardening exponent, n, occurred due to matrix hardening. Ductility and stress corrosion properties were considerably affected by both factors. Fractographic observations on the weld metal tested for stress-corrosion cracking (SCC) indicated a combination of transgranular cracking of the austenite and interface cracking.

A 3D-Printable Polymer-Metal Soft-Magnetic Functional Composite-Development and Characterization.

PubMed

Khatri, Bilal; Lappe, Karl; Noetzel, Dorit; Pursche, Kilian; Hanemann, Thomas

2018-01-25

In this work, a 3D printed polymer-metal soft-magnetic composite was developed and characterized for its material, structural, and functional properties. The material comprises acrylonitrile butadiene styrene (ABS) as the polymer matrix, with up to 40 vol. % stainless steel micropowder as the filler. The composites were rheologically analyzed and 3D printed into tensile and flexural test specimens using a commercial desktop 3D printer. Mechanical characterization revealed a linearly decreasing trend of the ultimate tensile strength (UTS) and a sharp decrease in Young's modulus with increasing filler content. Four-point bending analysis showed a decrease of up to 70% in the flexural strength of the composite and up to a two-factor increase in the secant modulus of elasticity. Magnetic hysteresis characterization revealed retentivities of up to 15.6 mT and coercive forces of up to 4.31 kA/m at an applied magnetic field of 485 kA/m. The composite shows promise as a material for the additive manufacturing of passive magnetic sensors and/or actuators.

A 3D-Printable Polymer-Metal Soft-Magnetic Functional Composite—Development and Characterization

PubMed Central

Lappe, Karl; Noetzel, Dorit; Pursche, Kilian; Hanemann, Thomas

2018-01-01

In this work, a 3D printed polymer–metal soft-magnetic composite was developed and characterized for its material, structural, and functional properties. The material comprises acrylonitrile butadiene styrene (ABS) as the polymer matrix, with up to 40 vol. % stainless steel micropowder as the filler. The composites were rheologically analyzed and 3D printed into tensile and flexural test specimens using a commercial desktop 3D printer. Mechanical characterization revealed a linearly decreasing trend of the ultimate tensile strength (UTS) and a sharp decrease in Young’s modulus with increasing filler content. Four-point bending analysis showed a decrease of up to 70% in the flexural strength of the composite and up to a two-factor increase in the secant modulus of elasticity. Magnetic hysteresis characterization revealed retentivities of up to 15.6 mT and coercive forces of up to 4.31 kA/m at an applied magnetic field of 485 kA/m. The composite shows promise as a material for the additive manufacturing of passive magnetic sensors and/or actuators. PMID:29370112

Effects of MgO modified β-TCP nanoparticles on the microstructure and properties of β-TCP/Mg-Zn-Zr composites.

PubMed

Zheng, H R; Li, Z; You, C; Liu, D B; Chen, M F

2017-03-01

The mechanical properties and corrosion resistance of magnesium alloy composites were improved by the addition of MgO surface modified tricalcium phosphate ceramic nanoparticles (m-β-TCP). Mg-3Zn-0.8Zr composites with unmodified (MZZT) and modified (MZZMT) nanoparticles were produced by high shear mixing technology. Effects of MgO m-β-TCP nanoparticles on the microstructure, mechanical properties, electrochemical corrosion properties and cytocompatibility of Mg-Zn-Zr/β-TCP composites were investigated. After hot extrusion deformation and dynamic recrystallization, the grain size of MZZMT was the half size of MZZT and the distribution of m-β-TCP particles in the matrix was more uniform than β-TCP particles. The yield tensile strength (YTS), ultimate tensile strength (UTS), and corrosion potential (Ecorr) of MZZMT were higher than MZZT; the corrosion current density (I corr ) of MZZMT was lower than MZZT. Cell proliferation of co-cultured MZZMT and MZZT composite samples were roughly the same and the cell number at each time point is higher for MZZMT than for MZZT samples.

New horizon for high performance Mg-based biomaterial with uniform degradation behavior: Formation of stacking faults

PubMed Central

Zhang, Jinghuai; Xu, Chi; Jing, Yongbin; Lv, Shuhui; Liu, Shujuan; Fang, Daqing; Zhuang, Jinpeng; Zhang, Milin; Wu, Ruizhi

2015-01-01

Designing the new microstructure is an effective way to accelerate the biomedical application of magnesium (Mg) alloys. In this study, a novel Mg–8Er–1Zn alloy with profuse nano-spaced basal plane stacking faults (SFs) was prepared by combined processes of direct-chill semi-continuous casting, heat-treatment and hot-extrusion. The formation of SFs made the alloy possess outstanding comprehensive performance as the biodegradable implant material. The ultimate tensile strength (UTS: 318 MPa), tensile yield strength (TYS: 207 MPa) and elongation (21%) of the alloy with SFs were superior to those of most reported degradable Mg-based alloys. This new alloy showed acceptable biotoxicity and degradation rate (0.34 mm/year), and the latter could be further slowed down through optimizing the microstructure. Most amazing of all, the uniquely uniform in vitro/vivo corrosion behavior was obtained due to the formation of SFs. Accordingly we proposed an original corrosion mechanism for the novel Mg alloy with SFs. The present study opens a new horizon for developing new Mg-based biomaterials with highly desirable performances. PMID:26349676

Improved UT1 Predictions through Low-Latency VLBI Observations

DTIC Science & Technology

2010-03-14

J Geod (2010) 84:399–402 DOI 10.1007/s00190-010-0372-8 SHORT NOTE Improved UT1 predictions through low-latency VLBI observations Brian Luzum · Axel...polar motion and nutation on UT1 determinations from VLBI Intensive obser- vations. J Geod 82(12):863. doi:10.1007/s00190-008-0212-2 Ray JR, Carter WE...Behrend D (2007) The International VLBI Service for Geodesy and Astrometry (IVS): current capabilities and future prospects. J Geod 81(6–8):479. doi

Disposition of feedwater nozzle UT indications in a BWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leshnoff, S.D.; Orski, M.A.

A technical logic is developed, which justifies the disposition of feedwater nozzle ultrasonic testing (UT) indications in order to return to operation without visual inspection of the vessel inside surface. Present regulatory guidance is to inspect the inside surface from the inside if a reportable indication is found. A highly sensitive, tomographic UT technique, developed by Kraftwerk Union, is used to detect and size machined notches in the blend radius and bore regions of a full-sized feedwater nozzle mock-up.

Hariswaran Sitaraman | NREL

Science.gov Websites

pertaining to combustion and particulate flows. Education 2013 Ph.D., Aerospace Engineering, UT, Austin 2010 M.S., Aerospace Engineering, UT, Austin 2008 B. Tech, Aerospace Engineering, IIT Madras, Chennai

Antigenic and functional properties of the human red blood cell urea transporter hUT-B1.

PubMed

Lucien, Nicole; Sidoux-Walter, Frédéric; Roudier, Nathalie; Ripoche, Pierre; Huet, Martine; Trinh-Trang-Tan, Marie-Marcelle; Cartron, Jean-Pierre; Bailly, Pascal

2002-09-13

The Kidd (JK) blood group locus encodes the urea transporter hUT-B1, which is expressed on human red blood cells and other tissues. The common JK*A/JK*B blood group polymorphism is caused by a single nucleotide transition G838A changing Asp-280 to Asn-280 on the polypeptide, and transfection of erythroleukemic K562 cells with hUT-B1 cDNAs carrying either the G838 or the A838 nucleotide substitutions resulted in the isolation of stable clones that expressed the Jk(a) or Jk(b) antigens, respectively, thus providing the first direct demonstration that the hUT-B1 gene encodes the Kidd blood group antigens. In addition, immunochemical analysis of red blood cells demonstrated that hUT-B1 also exhibits ABO determinants attached to the single N-linked sugar chain at Asn-211. Moreover, immunoadsorption studies, using inside-out and right-side-out red cell membrane vesicles as competing antigen, demonstrated that the C- and N-terminal ends of hUT-B1 are oriented intracellularly. Mutagenesis and functional studies by expression in Xenopus oocytes revealed that both cysteines Cys-25 and Cys-30 (but not alone) are essential for plasma membrane addressing. Conversely, the transport function was not affected by the JK*A/JK*B polymorphism, C-terminal deletion (residues 360-389), or mutation of the extracellular N-glycosylation consensus site and remains poorly para-chloromercuribenzene sulfonate (pCMBS)-sensitive. However, transport studies by stopped flow light scattering using Jk-K562 transfectants demonstrated that the hUT-B1-mediated urea transport is pCMBS-sensitive in an erythroid context, as reported previously for the transporter of human red blood cells. Mutagenesis analysis also indicated that Cys-151 and Cys-236, at least alone, are not involved in pCMBS inhibition. Altogether, these antigenic, topologic, and functional properties might have implications into the physiology of hUT-B1 and other members of the urea transporter family.

Multi-point observations of Ion Dispersions near the Exterior Cusp with Cluster

NASA Astrophysics Data System (ADS)

Escoubet, C.-Philippe; Grison, Benjamin; Berchem, Jean; Trattner, Kralheinz; Pitout, Frederic; Richard, Robert; Taylor, Matt; Soucek, Jan; Laakso, Harri; Masson, Arnaud; Dunlop, Malcolm; Dandouras, Iannis; Reme, Henri; Fazakerley, Andrew; Daly, Patrick

2014-05-01

The exterior cusp is the most external region of the polar magnetosphere in direct contact with the plasma and the magnetic field from the solar wind. Unlike the rest of the magnetopause surface, the exterior cusp is a singular region with small and turbulent magnetic field and where large entry of plasma from solar origin takes place. The main process that injects solar wind plasma into the polar cusp is now generally accepted to be magnetic reconnection. Depending on the IMF direction, this process will take place equatorward (for IMF southward), poleward (for IMF northward) or on the dusk or dawn sides (for IMF azimuthal) of the cusp. We report a Cluster crossing on 5 January 2002 near the exterior cusp on the southern dusk side. The IMF was mainly azimuthal (IMF-By around -5 nT), the solar wind speed lower than usual around 280 km/s and the density around 5 cm-3. The four Cluster spacecraft were still in the "magnetotail" configuration with two perfect tetrahedra of 2000 km around apogee and turning into an elongated configuration near the magnetopause. C4 was the first spacecraft to enter the cusp around 19:52:04 UT, followed by C2 at 19:52:35 UT, C1 at 19:54:24 UT and C3 at 20:13:15 UT. C4 and C1 observed two ion energy dispersions at 20:10 UT and 20:40 UT and C3 at 20:35 UT and 21:15 UT. Using the time of flight technique on the upgoing and downgoing ions in the dispersions, we obtain an altitude of the sources of these ions between 14 and 20 RE. Using Tsyganenko model, these sources are located on the dusk flank, past the terminator. In addition, before entering the cusp, the magnetopause crossing was characterized by a large shear in By and bipolar plasma flows, suggesting that reconnection was taking place near the exterior cusp. We will discuss the extent of the reconnection line along the flank of the magnetopause based on these observations.

Improving a Bimanual Motor Skill Through Unimanual Training

PubMed Central

Hayashi, Takuji; Nozaki, Daichi

2016-01-01

When we learn a bimanual motor skill (e.g., rowing a boat), we often break it down into unimanual practices (e.g., a rowing drill with the left or right arm). Such unimanual practice is thought to be useful for learning bimanual motor skills efficiently because the learner can concentrate on learning to perform a simpler component. However, it is not so straightforward to assume that unimanual training (UT) improves bimanual performance. We have previously demonstrated that motor memories for reaching movements consist of three different parts: unimanual-specific, bimanual-specific, and overlapping parts. According to this scheme, UT appears to be less effective, as its training effect is only partially transferred to the same limb for bimanual movement. In the present study, counter-intuitively, we demonstrate that, even after the bimanual skill is almost fully learned by means of bimanual training (BT), additional UT could further improve bimanual skill. We hypothesized that this effect occurs because UT increases the memory content in the overlapping part, which might contribute to an increase in the memory for bimanual movement. To test this hypothesis, we examined whether the UT performed after sufficient BT could improve the bimanual performance. Participants practiced performing bimanual reaching movements (BM) in the presence of a novel force-field imposed only on their left arm. As an index for the motor performance, we used the error-clamp method (i.e., after-effect of the left arm) to evaluate the force output to compensate for the force-field during the reaching movement. After sufficient BT, the training effect reached a plateau. However, UT performed subsequently improved the bimanual performance significantly. In contrast, when the same amount of BT was continued, the bimanual performance remained unchanged, highlighting the beneficial effect of UT on bimanual performance. Considering memory structure, we also expected that BT could improve unimanual performance, which was confirmed by another experiment. These results provide a new interpretation of why UT was useful for improving a bimanual skill, and propose a practical strategy for enhancing performance by performing training in various contexts. PMID:27471452

Mare and foal survival and subsequent fertility of mares treated for uterine torsion.

PubMed

Spoormakers, T J P; Graat, E A M; ter Braake, F; Stout, T A E; Bergman, H J

2016-03-01

Previous surveys have reported that mare and foal survival after correction of uterine torsion (UT) varies from 60 to 84% and from 30 to 54%, respectively. Furthermore, resolution via a standing flank laparotomy (SFL) has been associated with better foal, but not mare, survival. To compare the success of SFL with other correction methods (e.g. midline or flank laparotomy under general anaesthesia; correction per vaginam). Retrospective analysis of clinical records. Data on correction technique, stage of gestation, degree of rotation, survival and subsequent fertility for 189 mares treated for UT at 3 equine referral hospitals in The Netherlands during 1987-2007 were analysed. Mean stage of gestation at diagnosis was 283 days (range 153-369 days), with the majority of UTs (77.5%) occurring before Day 320 of gestation. After correction of UT, 90.5% of mares and 82.3% of foals survived to hospital discharge, between 3 and 39 days later, and to foaling. Multivariable logistic regression indicated that correction method and stage of gestation at UT affected survival of foals and mares. For foals, survival was 88.7% after SFL compared with 35.0% after other methods (P = 0.001). When UT occurred at <320 days, 90.6% of foals survived, compared with 56.1% at ≥320 days (P = 0.007). For mare survival, an interaction between stage of gestation and correction method was detected (P = 0.02), with higher survival after SFL (97.1%) than other methods (50.0%) at <320 days of gestation (P<0.01). When UT occurred at ≥320 days, mare survival did not differ between techniques (76.0 vs. 68.8%; P = 0.6). Of 123 mares that were bred again, 93.5% became pregnant; fertility did not differ between mares treated by SFL (93.9%) and other techniques (87.5%; P = 0.9). Standing flank laparotomy is the surgical technique of choice for resolving uncomplicated equine UT (i.e. with no coexisting gastrointestinal lesions) except when the stage of gestation exceeds 320 days. © 2015 EVJ Ltd.

The transverse technique; a complementary approach to the measurement of first-trimester uterine artery Doppler.

PubMed

Drouin, Olivier; Johnson, Jo-Ann; Chaemsaithong, Piya; Metcalfe, Amy; Huber, Janie; Schwarzenberger, Jill; Winters, Erin; Stavness, Lesley; Tse, Ada W T; Lu, Jing; Lim, Wan Teng; Leung, Tak Yeung; Bujold, Emmanuel; Sahota, Daljit; Poon, Liona C

2017-10-04

The objectives of this study were to 1) define the protocol for the first-trimester assessment of the uterine artery pulsatility index (UtA-PI) using the new transverse technique, 2) evaluate UtA-PI measured by the transverse approach versus that obtained by the conventional sagittal approach, and 3) determine if accelerated onsite training (both methods) of inexperienced sonographers can achieve reproducible UtA-PI measurements compared to that measured by an experienced sonographer. The study consists of 2 parts conducted in 2 centers (Part 1, Calgary, Canada and Part 2, Hong Kong). Part 1 Prospective observational study of women with singleton pregnancies between 11-13+6 weeks' gestation. UtA-PI measurements were performed using the 2 techniques (4 sonographers trained in both methods, 10 cases each) and measurement indices (PI), time required and subjective difficulty to obtain satisfactory measurements were compared. One sample t-test and Wilcoxon rank sign test was used when appropriate. Bland-Altman difference plots were used to assess measurement agreement, and intra-class correlation (ICC) was used to evaluate measurement reliability. A target plot was used to assess measures of central tendency and dispersion. Part 2 One experienced and three inexperienced sonographers prospectively measured the UtA-PI at 11-13+6 weeks' gestation in two groups of women (42 and 35, respectively), with singleton pregnancies using both approaches. Inexperienced sonographers underwent accelerated on-site training by the experienced sonographer. Measurement approach and sonographer order were on a random basis. ICC, Bland-Altman and Passing-Bablok analyses were performed to assess measurement agreement, reliability and effect of accelerated training. Part 1 We observed no difference in the mean time to acquire the measurements (Sagittal: 118 seconds vs Transverse: 106 seconds, p=0.38). The 4 sonographers reported the transverse technique was subjectively easier to perform (p=0.04). The bias (95% LOA) and the ICC between sagittal and transverse measurements was -0.05 (-0.48 to 0.37) and 0.94 for the mean UtA-PIs respectively. Measurements obtained using the transverse technique after correcting for gestation were significantly closer to the expected distribution than the sagittal technique. Part 2 There were no significant differences in the median UtA-PI measurements using the different approaches for both experienced and inexperienced sonographers (p>0.05 for all sonographers). Mean UtA-PI measurement reliability between approaches was high for the experienced (ICC=0.92) and inexperienced sonographers (ICC>0.81). UtA-PI measurement approaches did not deviate from linearity whilst biases ranged from -0.10 to 0.07. Median time required was similar (sagittal vs. transverse: 56.11 sec vs. 49.29 sec; p=0.054). This novel transverse approach for the measurement of UtA-PI in the first-trimester appears comparable to the sagittal approach and can be used in first-trimester preeclampsia screening. Providing accelerated onsite training can be helpful to improve UtA-PI measurement reliability and could potentially facilitate the broad implementation of first-trimester preeclampsia screening. This article is protected by copyright. All rights reserved.

The Accuracy of Radio Interferometric Measurements of Earth Rotation

NASA Technical Reports Server (NTRS)

Eubanks, T. M.; Steppe, J. A.; Spieth, M. A.

1985-01-01

The accuracy of very long base interferometry earth rotation (UT1) measurements is examined by intercomparing TEMPO and POLARIS data for 1982 and the first half of 1983. None of these data are simultaneous, and so a proper intercomparison requires accounting for the scatter introduced by the rapid, unpredictable, UT1 variations driven by exchanges of angular momentum with the atmosphere. A statistical model of these variations, based on meteorological estimates of the Atmospheric Angular Momentum is derived, and the optimal linear (Kalman) smoother for this model is constructed. The scatter between smoothed and independent raw data is consistent with the residual formal errors, which do not depend upon the actual scatter of the UT1 data. This represents the first time that an accurate prediction of the scatter between UT1 data sets were possible.

Using Phased Array Ultrasonic Testing in Lieu of Radiography for Acceptance of Carbon Steel Piping Welds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moran, Traci L.; Anderson, Michael T.; Cinson, Anthony D.

2014-08-01

The Pacific Northwest National Laboratory (PNNL) is conducting studies for the U.S. Nuclear Regulatory Commission (NRC) to assess the capability, effectiveness, and reliability of ultrasonic testing (UT) as a replacement method for radiographic testing (RT) for volumetric examination of nuclear power plant (NPP) components. This particular study focused on evaluating the use of UT on carbon steel plate welds. Welding fabrication flaws included a combination of planar and volumetric types, e.g., incomplete fusion, lack of penetration, cracks, porosity, and slag inclusions. The examinations were conducted using phased-array (PA) UT techniques applied primarily for detection and flaw type characterization. This papermore » will discuss the results of using UT in lieu of RT for detection and classification of fabrication flaws in carbon steel plate welds.« less

Electromyographic analysis of the serratus anterior and trapezius muscles during push-ups on stable and unstable bases in subjects with scapular dyskinesis.

PubMed

Pirauá, André Luiz Torres; Pitangui, Ana Carolina Rodarti; Silva, Juliana Pereira; Pereira dos Passos, Muana Hiandra; Alves de Oliveira, Valéria Mayaly; Batista, Laísla da Silva Paixão; Cappato de Araújo, Rodrigo

2014-10-01

The present study was performed to assess the electromyographic activity of the scapular muscles during push-ups on a stable and unstable surface, in subjects with scapular dyskinesis. Muscle activation (upper trapezius [UT]; lower trapezius [LT]; upper serratus anterior [SA_5th]; lower serratus anterior [SA_7th]) and ratios (UT/LT; UT/SA_5th; UT/ SA_7th) levels were determined by surface EMG in 30 asymptomatic men with scapular dyskinesis, during push-up performed on a stable and unstable surface. Multivariate analysis of variance with repeated measures was used for statistical analyses. The unstable surface caused a decrease in the EMG activity of the serratus anterior and an increase in EMG activity of the trapezius (p=0.001). UT/SA_5th and UT/ SA_7th ratios were higher during unstable push-ups (p=0.001). The results suggest that, in individuals with scapular dyskinesis, there is increased EMG activity of the trapezius and decreased EMG activity of the serratus anterior in response to an unstable surface. These results suggest that the performance of the push up exercise on an unstable surface may be more favorable to produce higher levels of trapezius activation and lower levels of serratus anterior activation. However, if the goal of the exercise program is the strengthening of the SA muscle, it is suggested to perform the push up on a stable surface. Copyright © 2014 Elsevier Ltd. All rights reserved.

Aerodynamics and pollen ultrastructure in Ephedra.

PubMed

Bolinder, Kristina; Niklas, Karl J; Rydin, Catarina

2015-03-01

• Pollen dispersal is affected by the terminal settling velocity (Ut) of the grains, which is determined by their size, bulk density, and by atmospheric conditions. The likelihood that wind-dispersed pollen is captured by ovulate organs is influenced by the aerodynamic environment created around and by ovulate organs. We investigated pollen ultrastructure and Ut of Ephedra foeminea (purported to be entomophilous), and simulated the capture efficiency of its ovules. Results were compared with those from previously studied anemophilous Ephedra species.• Ut was determined using stroboscopic photography of pollen in free fall. The acceleration field around an "average" ovule was calculated, and inflight behavior of pollen grains was predicted using computer simulations. Pollen morphology and ultrastructure were investigated using SEM and STEM.• Pollen wall ultrastructure was correlated with Ut in Ephedra. The relative proportion and amount of granules in the infratectum determine pollen bulk densities, and (together with overall size) determine Ut and thus dispersal capability. Computer simulations failed to reveal any functional traits favoring anemophilous pollen capture in E. foeminea.• The fast Ut and dense ultrastructure of E. foeminea pollen are consistent with functional traits that distinguish entomophilous species from anemophilous species. In anemophilous Ephedra species, ovulate organs create an aerodynamic microenvironment that directs airborne pollen to the pollination drops. In E. foeminea, no such microenvironment is created. Ephedroid palynomorphs from the Cretaceous share the ultrastructural characteristics of E. foeminea, and at least some may, therefore, have been produced by insect-pollinated plants. © 2015 Botanical Society of America, Inc.

Status and Prospects for Combined GPS LOD and VLBI UT1 Measurements

NASA Astrophysics Data System (ADS)

Senior, K.; Kouba, J.; Ray, J.

2010-01-01

A Kalman filter was developed to combine VLBI estimates of UT1-TAI with biased length of day (LOD) estimates from GPS. The VLBI results are the analyses of the NASA Goddard Space Flight Center group from 24-hr multi-station observing sessions several times per week and the nearly daily 1-hr single-baseline sessions. Daily GPS LOD estimates from the International GNSS Service (IGS) are combined with the VLBI UT1-TAI by modeling the natural excitation of LOD as the integral of a white noise process (i.e., as a random walk) and the UT1 variations as the integration of LOD, similar to the method described by Morabito et al. (1988). To account for GPS technique errors, which express themselves mostly as temporally correlated biases in the LOD measurements, a Gauss-Markov model has been added to assimilate the IGS data, together with a fortnightly sinusoidal term to capture errors in the IGS treatments of tidal effects. Evaluated against independent atmospheric and oceanic axial angular momentum (AAM + OAM) excitations and compared to other UT1/LOD combinations, ours performs best overall in terms of lowest RMS residual and highest correlation with (AAM + OAM) over sliding intervals down to 3 d. The IERS 05C04 and Bulletin A combinations show strong high-frequency smoothing and other problems. Until modified, the JPL SPACE series suffered in the high frequencies from not including any GPS-based LODs. We find, surprisingly, that further improvements are possible in the Kalman filter combination by selective rejection of some VLBI data. The best combined results are obtained by excluding all the 1-hr single-baseline UT1 data as well as those 24-hr UT1 measurements with formal errors greater than 5 μs (about 18% of the multi-baseline sessions). A rescaling of the VLBI formal errors, rather than rejection, was not an effective strategy. These results suggest that the UT1 errors of the 1-hr and weaker 24-hr VLBI sessions are non-Gaussian and more heterogeneous than expected, possibly due to the diversity of observing geometries used, other neglected systematic effects, or to the much shorter observational averaging interval of the single-baseline sessions. UT1 prediction services could benefit from better handling of VLBI inputs together with proper assimilation of IGS LOD products, including using the Ultra-rapid series that is updated four times daily with 15 hr delay.

A prospective randomized comparison of unsedated ultrathin versus standard esophagogastroduodenoscopy in routine outpatient gastroenterology practice: does it work better through the nose?

PubMed

Birkner, B; Fritz, N; Schatke, W; Hasford, J

2003-08-01

In an outpatient gastroenterological practice setting, highly effective diagnostic procedures and patient satisfaction play an important role. Ultrathin endoscopy in unsedated patients has been shown to be more cost-effective and time-efficient in comparison with standard endoscopy. A prospective randomized study was carried out in unsedated patients to compare performance, feasibility, safety, and patient tolerance between ultrathin transnasal (UT), ultrathin oral (UO), and standard (SO) esophagogastroduodenoscopy (EGD). A total of 200 of 600 eligible patients consented to participate in the study, and were randomly assigned to undergo UT, UO, or SO. Patients reported their tolerance of the procedure (anxiety, pain, gagging, and overall satisfaction; Likert scale 1-10), and the endoscopists reported the effectiveness of the procedure (handling, picture quality, and overall performance; Likert scale 1-10). Statistics were calculated using the Kruskal-Wallis test. After randomization, 65, 67, and 68 patients were allocated to the UT, UO, and SO groups, respectively. Failure to achieve complete EGD by the intended route occurred in 14 patients (22 %) in the UT group. Compared to the SO group, patients in the UT and UO groups rated anxiety before the procedure as being more intense - median score (10 % quantile estimate; 90 % quantile estimate): UT, 2.0 (1.0; 4.0); UO, 2.0 (1.0; 4.0); SO, 0.0 (0.0; 2.0); p < 0.0001), whereas SO patients experienced a higher level of anxiety during the procedure ( P < 0.0001). Pain during insertion of the endoscope was the least intense in the UO group: UT, 2.0 (1.0; 5.0); UO, 1.0 (1.0; 3.0); SO, 2.0 (1.0; 4.0); P < 0.001). Gagging during insertion was more pronounced in the UO group: UT, 2.0 (1.0; 4.0); UO, 3.0 (1.0; 7.0); SO, 2.0 (1.0; 5.0); P < 0.01). The patients' score for the overall assessment was better in the SO group ( P < 0.0001). The endoscopists' overall assessment for ultrathin EGD was poorer than for standard EGD: UT, 3.0 (2.0; 5.0); UO, 3.0 (2.0; 5.0); SO, 2.0 (1.0; 3.0); P < 0.0001). Ultrathin endoscopy through both the transnasal and oral routes has limited use in routine outpatient practice. Techniques for reducing pain and gagging may improve patient tolerance. Further technical improvements are needed to allow routine implementation.

Air impacts from three alternatives for producing JP-8 jet fuel.

PubMed

Kositkanawuth, Ketwalee; Gangupomu, Roja Haritha; Sattler, Melanie L; Dennis, Brian H; MacDonnell, Frederick M; Billo, Richard; Priest, John W

2012-10-01

To increase U.S. petroleum energy independence, the University of Texas at Arlington (UT Arlington) has developed a direct coal liquefaction process which uses a hydrogenated solvent and a proprietary catalyst to convert lignite coal to crude oil. This sweet crude can be refined to form JP-8 military jet fuel, as well as other end products like gasoline and diesel. This paper presents an analysis of air pollutants resulting from using UT Arlington's liquefaction process to produce crude and then JP-8, compared with 2 alternative processes: conventional crude extraction and refining (CCER), and the Fischer-Tropsch process. For each of the 3 processes, air pollutant emissions through production of JP-8 fuel were considered, including emissions from upstream extraction/ production, transportation, and conversion/refining. Air pollutants from the direct liquefaction process were measured using a LandTEC GEM2000 Plus, Draeger color detector tubes, OhioLumex RA-915 Light Hg Analyzer, and SRI 8610 gas chromatograph with thermal conductivity detector. According to the screening analysis presented here, producing jet fuel from UT Arlington crude results in lower levels of pollutants compared to international conventional crude extraction/refining. Compared to US domestic CCER, the UTA process emits lower levels of CO2-e, NO(x), and Hg, and higher levels of CO and SO2. Emissions from the UT Arlington process for producing JP-8 are estimated to be lower than for the Fischer-Tropsch process for all pollutants, with the exception of CO2-e, which were high for the UT Arlington process due to nitrous oxide emissions from crude refining. When comparing emissions from conventional lignite combustion to produce electricity, versus UT Arlington coal liquefaction to make JP-8 and subsequent JP-8 transport, emissions from the UT Arlington process are estimated to be lower for all air pollutants, per MJ of power delivered to the end user. The United States currently imports two-thirds of its crude oil, leaving its transportation system especially vulnerable to disruptions in international crude supplies. At current use rates, U.S. coal reserves (262 billion short tons, including 23 billion short tons lignite) would last 236 years. Accordingly, the University of Texas at Arlington (UT Arlington) has developed a process that converts lignite to crude oil, at about half the cost of regular crude. According to the screening analysis presented here, producing jet fuel from UT Arlington crude generates lower levels of pollutants compared to international conventional crude extraction/refining (CCER).

PREFACE: 19th International Conference on the Application of High Magnetic Fields in Semiconductor Physics and Nanotechnology (HMF-19)

NASA Astrophysics Data System (ADS)

Muraki, Koji; Takeyama, Shojiro

2011-12-01

This volume contains invited and contributed papers from the 19th International Conference on the Application of High Magnetic Fields in Semiconductor Physics and Nanotechnology (HMF-19) held in Fukuoka, Japan, from 1-6 August 2010. This conference was mainly sponsored by the Tokyo University-'Horiba International fund', which was donated by Dr Masao Horiba, the founder of Horiba Ltd. The scientific program of HMF-19 consisted of 37 invited talks, 24 contributed talks, and 83 posters, which is available from the conference homepage http://www.hmf19.iis.u-tokyo.ac.jp/index.html. Each manuscript submitted for publication in this volume has been independently reviewed. The Editor is very grateful to all the reviewers for their quick responses and helpful reports and to all the authors for their submissions and patience for the delay in the editorial process. Finally, the Editor would like to express his sincere gratitude to all the individuals involved in the conference organization and all the attendees, who made this conference so successful. Koji Muraki Conference photograph Committees Chair Conference chairS Takeyama(ISSP-UT) Conference secretary T Machida (IIS-UT) Program chair K Muraki (NTT) Local organizing chair K Oto (Chiba Univ.) Advisory Committee International Domestic L Brey (ES) T Ando (TIT) Z H Chen (CN) Y Hirayama (Tohoku Univ.) S Das Sarma (US) G Kido (NIMS) L Eaves (GB) N Miura (JP) J P Eisenstein (US) J Nitta (Tohoku Univ.) K Ensslin (CH) T Takamasu (NIMS) J Furdyna (US) G M Gusev (BR) I Kukushkin (RU) Z D Kvon (RU) G Landwehr (DE) J C Maan (NL) A H MacDonald (US) N F Oliveira Jr (BR) A Pinczuk (US) J C Portal (FR) A Sachrajda (CA) M K Sanyal(IN) R Stepniewski(PL) Program Committee Chair: K Muraki(NTT) International Domestic G Bauer (AU) H Ajiki (Osaka Univ.) G Boebinger (US) H Aoki (Hongo, UT) S Ivanov (RU) K Nomura (RIKEN) K von Klitzing (DE) T Okamoto (Hongo, UT) R Nicholas (GB) T Osada (ISSP-UT ) M Potemski (FR) N Studart (BR) U Zeitler (NL) Local Organizing Committee Chair: K Oto(Chiba Univ.) Y H Matsuda (ISSP-UT) H Yokoi (Kumamoto Univ.) M Itoh (IIS-UT) M Noda (ISSP-UT) H Sawabe (ISSP-UT) Sponsors Horiba International Conference (Dr Masao Horiba's Donation) The University of Tokyo Fukuoka City The Institute for Solid State Physics, The University of Tokyo The Global Center of Excellence for Physical Sciences Frontier, The University of Tokyo

VizieR Online Data Catalog: Follow-up photometry and spectroscopy of KELT-17 (Zhou+, 2016)

NASA Astrophysics Data System (ADS)

Zhou, G.; Rodriguez, J. E.; Collins, K. A.; Beatty, T.; Oberst, T.; Heintz, T. M.; Stassun, K. G.; Latham, D. W.; Kuhn, R. B.; Bieryla, A.; Lund, M. B.; Labadie-Bartz, J.; Siverd, R. J.; Stevens, D. J.; Gaudi, B. S.; Pepper, J.; Buchhave, L. A.; Eastman, J.; Colon, K.; Cargile, P.; James, D.; Gregorio, J.; Reed, P. A.; Jensen, E. L. N.; Cohen, D. H.; McLeod, K. K.; Tan, T. G.; Zambelli, R.; Bayliss, D.; Bento, J.; Esquerdo, G. A.; Berlind, P.; Calkins, M. L.; Blancato, K.; Manner, M.; Samulski, C.; Stockdale, C.; Nelson, P.; Stephens, D.; Curtis, I.; Kielkopf, J.; Fulton, B. J.; Depoy, D. L.; Marshall, J. L.; Pogge, R.; Gould, A.; Trueblood, M.; Trueblood, P.

2017-05-01

KELT-17, the first exoplanet host discovered through the combined observations of both the Kilodegree Extremely Little Telescope (KELT)-North and KELT-South, is located in KELT-South field 06 (KS06) and KELT-North field 14 (KN14), which are both centered on α=07h39m36s δ=+03°00'00'' (J2000). At the time of identification, the post-processed KELT data set included 2092 images from KN14, taken between UT 2011 October 11 and UT 2013 March 26 and 2636 images from KS06 taken between UT 2010 March 02 and 2013 May 10. The discovery light curves from both KELT-North and KELT-South are shown in Figure1. We obtained higher spatial resolution and precision photometric follow-up observations of KELT-17b in multiple filters. An I-band transit was observed on UT 2015 March 05 at the Canela's Robotic Observatory (CROW) with the 0.3m SCT12 telescope, remotely operated from Portalegre, Portugal. Observations were acquired with the ST10XME CCD camera, with a 30'*20' field of view and a 0.86'' pixel scale. A full multi-color (V and I) transit of KELT-17b was observed on UT 2015 March 12 at Kutztown University Observatory (KUO), located on the campus of Kutztown University in Kutztown, Pennsylvania. KUO's main instrument is the 0.6 m Ritchey-Chretien optical telescope with a focal ratio of f/8. The imaging CCD (KAF-6303E) camera has an array of 3K*2K (9μm) pixels and covers a field of view of 19.5'*13.0'. The Peter van de Kamp Observatory (PvdK) at Swarthmore College (near Philadelphia) houses a 0.62m Ritchey-Chretien reflector with a 4K*4K pixel Apogee CCD. The telescope and camera together have a 26'*26' field of view and a 0.61'' pixel scale. PvdK observed KELT-17b on UT 2015 March 12 in the SDSS z' filter. KELT-17b was observed in both g' and i' on UT 2015 March 12 at Wellesley College's Whitin Observatory in Massachusetts. The telescope is a 0.6m Boller and Chivens with a DFM focal reducer yielding an effective focal ratio of f/9.6. We used an Apogee U230 2K*2K camera with a 0.58''/pixel scale and a 20'*20' field of view. One full transit of KELT-17b was observed from the Westminster College Observatory (WCO), PA, on UT 2015 November 4 in the z' filter. The observations employed a 0.35m f/11 Celestron C14 Schmidt-Cassegrain telescope and SBIG STL-6303E CCD with a ~3K*2K array of 9μm pixels, yielding a 24'*16' field of view and 1.4''/pixel image scale at 3*3 pixel binning. The stellar FWHM was seeing-limited with a typical value of ~3.2''. Three full transits of KELT-17b were observed on UT 2016 February 26 (g' and i') and UT 2016 March 31 (r') using the Manner-Vanderbilt Ritchie-Chrtien (MVRC) telescope located at the Mt. Lemmon summit of Steward Observatory, AZ. The observations employed a 0.6m f/8 RC Optical Systems Ritchie-Chretien telescope and SBIG STX-16803 CCD with a 4K*4K array of 9μm pixels, yielding a 26'*26' field of view and 0.39''/pixel image scale. The telescope was heavily defocused for all three observations resulting in a typical stellar FWHM of ~17''. The Perth Exoplanet Survey Telescope (PEST) observatory is a backyard observatory owned and operated by ThiamGuan (TG) Tan, located in Perth, Australia. It is equipped with a 0.3m Meade LX200 SCT f/10 telescope with focal reducer yielding f/5 and an SBIG ST-8XME CCD camera. The telescope and camera combine to have a 31'*21' field of view and a 1.2'' pixel scale. PEST observed KELT-17b on UT 2016 March 06 in the B band. A series of spectroscopic follow-up observations were performed to characterize the KELT-17 system. We performed low-resolution, high-signal-to-noise reconnaissance spectroscopic follow-up of KELT-17 using the Wide Field Spectrograph (WiFeS) on the Australian National University (ANU) 2.3m telescope at Siding Spring Observatory, Australia in 2015 February. In-depth spectroscopic characterization of KELT-17 was performed by the Tillinghast Reflector Echelle Spectrograph (TRES) on the 1.5m telescope at the Fred Lawrence Whipple Observatory, Mount Hopkins, Arizona, USA. TRES has a wavelength coverage of 3900-9100Å over 51 echelle orders, with a resolving power of λ/Δλ R=44000. A total of 12 out-of-transit observations were taken to characterize the radial velocity orbital variations exhibited by KELT-17. In addition, we also observed spectroscopic transits of KELT-17b with TRES on 2016 February 23 and 2016 February 26 UT, gathering 33 and 29 sets of spectra, respectively. (4 data files).

Simulated microgravity induce apoptosis and down-regulation of erythropoietin receptor of UT-7/EPO cells

NASA Astrophysics Data System (ADS)

Zou, Li-xue; Cui, Shao-yan; Zhong, Jian; Yi, Zong-chun; Sun, Yan; Fan, Yu-bo; Zhuang, Feng-yuan

2010-11-01

Hematopoietic progenitor cell proliferation can be alternated on either spaceflight or under simulated microgravity experiments on the ground; however, the underlying mechanism remains largely unknown. In the present study, we have demonstrated that exposure of human erythropoietin (EPO)-dependent leukemia cell line UT-7/EPO cells to conditions of simulated microgravity with a rotary culture instrument significantly inhibited the cellular proliferation rate. Adding higher concentrations of EPO to the culture medium failed to improve the inhibitory status. Cell apoptosis was detected by fluorescence staining of cell nuclei and a flow cytometry assay using Annexin V/PI double staining. This microgravity-induced apoptosis in UT-7/EPO cells could be blocked by a pancaspase inhibitor Z-VAD-FMK. Immunoblotting demonstrated that rotary culture resulted in a reduction of the expression of Bcl-xL, an anti-apoptotic protein, and the cleavage of caspase-3. Furthermore, rotary culture reduced surface localization and protein content, as well as the mRNA expression of erythropoietin receptor (EPOR) of UT-7/EPO. Take together, the findings indicated that simulated microgravity may induce mitochondrial related apoptosis of UT-7/EPO cell through depressing the EPO-EPOR pathway.

Joint NuSTAR and IRIS observation of a microflaring active region

NASA Astrophysics Data System (ADS)

Hannah, I. G.; Kleint, L.; Krucker, S.; Glesener, L.; Grefenstette, B.

2017-12-01

We present observations of a weakly microflaring active region observed in X-rays with NuSTAR, UV with IRIS and EUV with SDO/AIA. NuSTAR was pointed at this unnamed active region near the East limb between 23:27UT and 23:37UT 26-July-2016, finding mostly quiescent emission except for a small microflare about 23:35UT. The NuSTAR spectrum for the pre-microflare time (23:27UT to 23:34UT) is well fitted by a single thermal component of about 3MK and combined with SDO/AIA we can determine the differential emission measure (DEM), finding it, as expected, drops very sharply to higher temperatures. During the subsequent microflare, the increase in NuSTAR counts matches a little brightening loop observed with IRIS SJI 1400Å and SDO/AIA. Fortuitously the IRIS slit crosses this microflaring loop and we find an increased emission in Si IV 1394Å, Si IV 1403Å and O IV 1402Å but only average line widths and velocities. The NuSTAR microflare spectrum shows heating to higher temperatures and also allows us to investigate the energetics of this event.

On the mechanical properties of tooth enamel under spherical indentation.

PubMed

Chai, Herzl

2014-11-01

The mechanical properties of tooth enamel generally exhibit large variations, which reflect its structural and material complexity. Some key properties were evaluated under localized contact, simulating actual functioning conditions. Prominent cusps of extracted human molar teeth were polished down ~0.7 mm below the cusp tip and indented by tungsten carbide balls. The internal damage was assessed after unloading from longitudinal or transverse sections. The ultimate tensile stress (UTS) was determined using a novel bilayer specimen. The damage is characterized by penny-like radial cracks driven by hoop stresses and cylindrical cracks driven along protein-rich interrod materials by shear stresses. Shallow cone cracks typical of homogeneous materials which may cause rapid tooth wear under repeat contact are thus avoided. The mean stress vs. indentation strain curve is highly nonlinear, attributable to plastic shearing of protein between and within enamel rods. This curve is also affected by damage, especially radial cracks, the onset of which depends on ball radius. Several material properties were extracted from the tests, including shear strain at the onset of ring cracks γ(F) (=0.14), UTS (=119 MPa), toughness K(C) (=0.94 MPa m(1/2)), a crack propagation law and a constitutive response determined by trial and error with the aid of a finite-element analysis. These quantities, which are only slightly sensitive to anatomical location within the enamel region tested, facilitate a quantitative assessment of crown failure. Causes for variations in published UTS and K(C) values are discussed. Copyright © 2014 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Combinations of Earth Orientation Measurements: SPACE94, COMB94, and POLE94

NASA Technical Reports Server (NTRS)

Gross, Richard S.

1996-01-01

A Kalman filter has been used to combine independent measurements of the Earth's orientation taken by the space-geodetic observing techniques of lunar laser ranging, satellite laser ranging, very long baseline interferometry, and the Global Positioning System. Prior to their combination, the data series were adjusted to have the same bias and rate, the stated uncertainties of the measurements were adjusted, and data points considered to be outliers were deleted. The resulting combination, SPACE94, consists of smoothed, interpolated polar motion and UT1-UTC values spanning October 6, 1976, to January 27, 1995, at 1-day intervals. The Kalman filter was then used to combine the space-geodetic series comprising SPACE94 with two different, independent series of Earth orientation measurements taken by the technique of optical astrometry. Prior to their combination with SPACE94, the bias, rate and annual term of the optical astrometric series were corrected, the stated uncertainties of the measurements were adjusted, and data points considered to be outliers were deleted. The adjusted optical astrometric series were then combined with SPACE94 in two steps: (1) the Bureau International de l'Heure (BIH) optical astrometric series was combined with SPACE94 to form COMB94, a combined series of smoothed, interpolated polar motion and UT1-UTC values spanning January 20, 1962, to January 27, 1995, at 5-day intervals, and (2) the International Latitude Service (ILS) optical astrometric series was combined with COMB94 to form POLE94, a combined series of smoothed, interpolated polar motion values spanning January 20, 1900, to January 21, 1995, at 30.4375-day intervals.

X-ray Pulsations from AXP 1E 1547-5407 Detected with RXTE

NASA Astrophysics Data System (ADS)

Dib, R.; Kaspi, V. M.; Gavriil, F. P.; Woods, P. M.

2008-10-01

We observed AXP 1E 1547-5407 which is currently in outburst (see ATELs #1756, #1761, #1763) with RXTE on October 4 (4 ks), and 6 (1.4 ks, 1.6 ks). The 2-20 keV pulse profile of these observations (October 04 UT 21:51:04, October 06 UT 01:46:04, and October 06 UT 23:31:04) shows a single broad pulse that is qualitatively similar to that reported in Halpern et al. (2008, ApJ, 676, 1178), though there is a possible hint of additional peaks.

Characterization of the near-Earth Asteroid 2002 NY40

DTIC Science & Technology

2007-09-01

central wavelength for a given observation, it typically operates in two modes, a blue -wavelength mode that ranges from 4000–7000 Å and a red...wavelength mode that covers 6000–9000 Å. The blue mode currently operates with a long pass filter configuration blocking all wavelengths shorter than 4000 Å... blue spectra were taken from 9:10–9:54 UT and red spectra were taken from 10:59–11:25 UT. Additional red data were taken on the 18th from 8:41–9:17 UT

Direct Measurements of the Convective Recycling of the Upper Troposphere

NASA Technical Reports Server (NTRS)

Bertram, Timothy H.; Perring, Anne E.; Wooldridge, Paul J.; Crounse, John D.; Kwan, Alan J.; Wennberg, Paul O.; Scheuer, Eric; Dibb, Jack; Avery, Melody; Sachse, Glen;

Experimental Studies on Al (5.7% Zn) Alloy based Hybrid MMC

NASA Astrophysics Data System (ADS)

Shivaprakash, Y. M.; Ramu, H. C.; Chiranjivee; Kumar, Roushan; Kumar, Deepak

2018-02-01

In this investigation, an attempt is made to disperse SiC (20-25 microns) and Gr (15-20 microns) in the aluminium alloy having Zn, Mg and coper as major alloying elements. The composite is further subjected to mechanical testing to determine various properties like hardness, tensile strength and wear resistance. The alloy and composite samples were tested in the un heat treated conditions. All the tests were done at the laboratory conditions as per ASTM standards. The Pin-On-Disc tribometer is used to test the two-body abrasive sliding wear behaviour in dry conditions. The wear pattern is analysed by the optical images of worn surface taken in an inverted metallurgical microscope. The calculated density is found to be reducing as the SiC and Gr quantity is increased in the base alloy. The as cast Al alloy was found to be having highest hardness. The introduction of SiC tend to increase the hardness and UTS, since Gr is also introduced simultaneously which tends to reduce the hardness and UTS of composite. The composite having highest quantity of Gr showed superior wear resistance which is mainly because the Gr particulates provide an inbuilt lubricating properties to composite. The analysis of images of worn surface showed the abrasive and delamination pattern of wear. The composites developed in the present work can be used in the automobile and aerospace parts that are light in weight and require self-lubricating properties to enhance the wear resistance.

Bone bonding ability of a chemically and thermally treated low elastic modulus Ti alloy: gum metal.

PubMed

Tanaka, Masashi; Takemoto, Mitsuru; Fujibayashi, Shunsuke; Kawai, Toshiyuki; Yamaguchi, Seiji; Kizuki, Takashi; Matsushita, Tomiharu; Kokubo, Tadashi; Nakamura, Takashi; Matsuda, Shuichi

2014-03-01

The gum metal with composition Ti-36Nb-2Ta-3Zr-0.3O, is free from cytotoxic elements and exhibits a low elastic modulus as well as high mechanical strength. We have previously demonstrated that this gum metal, once subjected to a series of surface treatments--immersion in 1 M NaOH (alkali treatment) and then 100 mM CaCl2, before heating at 700 °C (sample: ACaH-GM), with an optional final hot water immersion (sample: ACaHW-GM)--has apatite-forming ability in simulated body fluid. To confirm the in vivo bioactivity of these treated alloys, failure loads between implants and bone at 4, 8, 16, and 26 weeks after implantation in rabbits' tibiae were measured for untreated gum metal (UT-GM), ACaH-GM and ACaHW-GM, as well as pure titanium plates after alkali and heat treatment (AH-Ti). The ACaH-GM and UT-GM plates showed almost no bonding, whereas ACaHW-GM and AH-Ti plates showed successful bonding by 4 weeks, and their failure loads subsequently increased with time. The histological findings showed a large amount of new bone in contact with the surface of ACaHW-GM and AH-Ti plates, suggesting that the ACaHW treatment could impart bone-bonding bioactivity to a gum metal in vivo. Thus, with this improved bioactive treatment, these advantageous gum metals become useful candidates for orthopedic and dental devices.

Development of 70/30 Poly-L-DL-Lactic Acid Filaments for 3D Printers (Part 2): Mechanical and Surface Properties of Bioabsorbable Printed Plates for Biomedical Applications

NASA Astrophysics Data System (ADS)

Fernandes, Daniel J.; Vidal, Rafael; Assayag, Ariel; de Biasi, Ronaldo S.; Elias, Carlos N.

2017-01-01

The mechanical, chemical, roughness and wettability properties of 70/30 poly (L,DL-lactide acid) three-dimensional (3D)-printed surgical plates made with extruded polymer filaments developed in the first part of this work were investigated. The plates were printed with horizontal (HRZ) and vertical (VRT) running layer orientations and evaluated by tensile, Fourier transform infrared (FTIR), optical perfilometry and wettability tests before and after degradation in simulated body fluid (SBF) for 21 days. The results show that the ultimate tensile strength (UTS) of HRZ plates before immersion in SBF was higher (34.1 MPa) than that of VRT plates (31.8 MPa). The Young's modulus ( E) of HRZ plates and VRT plates are similar (4 GPa). After immersion in SBF, the UTS of HRZ plates dropped to 20.5 MPa and E decreased to 3.3 GPa. VRT were not tested after SBF immersion due to the large degradation. FTIR analysis showed no evidence of chemical change in the plates after immersion in SBF. The roughness parameter R3z of VRT surfaces (19.54 µm) was higher than that of the HRZ surfaces (12.80 µm). The roughness parameters increased after degradation in SBF ( p = 0.7048). The contact angles of HRZ surfaces before immersion in SBF (66.28°) were higher than after immersion in SBF (18.12°); the same behavior was also observed in VRT plates.

Effects of crosslinking on the mechanical properties, drug release and cytocompatibility of protein polymers.

PubMed

Martinez, Adam W; Caves, Jeffrey M; Ravi, Swathi; Li, Wehnsheng; Chaikof, Elliot L

2014-01-01

Recombinant elastin-like protein polymers are increasingly being investigated as component materials of a variety of implantable medical devices. This is chiefly a result of their favorable biological properties and the ability to tailor their physical and mechanical properties. In this report, we explore the potential of modulating the water content, mechanical properties, and drug release profiles of protein films through the selection of different crosslinking schemes and processing strategies. We find that the selection of crosslinking scheme and processing strategy has a significant influence on all aspects of protein polymer films. Significantly, utilization of a confined, fixed volume, as well as vapor-phase crosslinking strategies, decreased protein polymer equilibrium water content. Specifically, as compared to uncrosslinked protein gels, water content was reduced for genipin (15.5%), glutaraldehyde (GTA, 24.5%), GTA vapor crosslinking (31.6%), disulfide (SS, 18.2%) and SS vapor crosslinking (25.5%) (P<0.05). Distinct crosslinking strategies modulated protein polymer stiffness, strain at failure and ultimate tensile strength (UTS). In all cases, vapor-phase crosslinking produced the stiffest films with the highest UTS. Moreover, both confined, fixed volume and vapor-phase approaches influenced drug delivery rates, resulting in decreased initial drug burst and release rates as compared to solution phase crosslinking. Tailored crosslinking strategies provide an important option for modulating the physical, mechanical and drug delivery properties of protein polymers. Copyright © 2013 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Impact of Aerosol Model Selection on Water-Leaving Radiance Retrievals from Satellite Ocean Color Imagery

DTIC Science & Technology

2012-11-22

tion Imagin e Aerosol ust 2010. P ve humidit aerosol m odel indic e 5 × 5 box f 10% and 5 alue would in the size OA Lt val the retriev rger impact...mparison p points for 6, 247, and ptical Dep compare A e location Lw matchup AOD value 18. AOD risons, Ven DIS vs. S t for descr en MODIS oints, 2...366 n Figure 17 ut of the 1 osol mode . sured value ups lead t satellite an NET) T, and purple. 0 . 5 ls s o d R r n ( in f a p m

Prediction of UT1-UTC, LOD and AAM χ3 by combination of least-squares and multivariate stochastic methods

NASA Astrophysics Data System (ADS)

Niedzielski, Tomasz; Kosek, Wiesław

2008-02-01

This article presents the application of a multivariate prediction technique for predicting universal time (UT1-UTC), length of day (LOD) and the axial component of atmospheric angular momentum (AAM χ 3). The multivariate predictions of LOD and UT1-UTC are generated by means of the combination of (1) least-squares (LS) extrapolation of models for annual, semiannual, 18.6-year, 9.3-year oscillations and for the linear trend, and (2) multivariate autoregressive (MAR) stochastic prediction of LS residuals (LS + MAR). The MAR technique enables the use of the AAM χ 3 time-series as the explanatory variable for the computation of LOD or UT1-UTC predictions. In order to evaluate the performance of this approach, two other prediction schemes are also applied: (1) LS extrapolation, (2) combination of LS extrapolation and univariate autoregressive (AR) prediction of LS residuals (LS + AR). The multivariate predictions of AAM χ 3 data, however, are computed as a combination of the extrapolation of the LS model for annual and semiannual oscillations and the LS + MAR. The AAM χ 3 predictions are also compared with LS extrapolation and LS + AR prediction. It is shown that the predictions of LOD and UT1-UTC based on LS + MAR taking into account the axial component of AAM are more accurate than the predictions of LOD and UT1-UTC based on LS extrapolation or on LS + AR. In particular, the UT1-UTC predictions based on LS + MAR during El Niño/La Niña events exhibit considerably smaller prediction errors than those calculated by means of LS or LS + AR. The AAM χ 3 time-series is predicted using LS + MAR with higher accuracy than applying LS extrapolation itself in the case of medium-term predictions (up to 100 days in the future). However, the predictions of AAM χ 3 reveal the best accuracy for LS + AR.

Creep and Fatigue in Inert and Vacuum Environments of Woven Sylramic-iBN Melt-Infiltrated Composites (Preprint)

DTIC Science & Technology

2011-07-01

300 400 500 Time, hr R up tu re S tre ng th o f F ib er s, M Pa approximate stress-rupture behavior of Syl...8 T x Tq f c c o                2 11 (2) Where q is the probability of failure of a fiber (equation 24 in reference...1/1 2 12 2 1                   m o UTS c mm m m m f  (5) Then, the in-situ strength of individual

75 FR 10995 - IFR Altitudes; Miscellaneous Amendments

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-10

... Read in Part Alma, GA VORTAC......... Dublin, GA *3000 VORTAC. *1700--MOCA *2000--GNSS MEA Alma R-345... V626 Is Amended To Read in Part Myton, UT VORTAC Ymont, UT FIX *15000 *12600--MOCA *12600--GNSS MEA...

Use of anaerobic hydrolysis pretreatment to enhance ultrasonic disintegration of excess sludge.

PubMed

Li, Xianjin; Zhu, Tong; Shen, Yang; Chai, Tianyu; Xie, Yuanhua; You, Meiyan; Wang, Youzhao

2016-01-01

To improve the excess sludge disintegration efficiency, reduce the sludge disintegration cost, and increase sludge biodegradability, a combined pretreatment of anaerobic hydrolysis (AH) and ultrasonic treatment (UT) was proposed for excess sludge. Results showed that AH had an advantage in dissolving flocs, modifying sludge characteristics, and reducing the difficulty of sludge disintegration, whereas UT was advantageous in damaging cell walls, releasing intracellular substances, and decomposing macromolecular material. The combined AH-UT process was an efficient method for excess sludge pretreatment. The optimized solution involved AH for 3 days, followed by UT for 10 min. After treatment, chemical oxygen demand, protein, and peptidoglycan concentrations reached 3,949.5 mg O2/L, 752.5 mg/L and 619.1 mg/L, respectively. This work has great significance for further engineering applications, namely, reducing energy consumption, increasing the sludge disintegration rate, and improving the biochemical properties of sludge.

Carcinome à cellule vitreuse du col de l'utérus: à propos d'un cas et revue de littérature

PubMed Central

Hakimi, Ihssane; Zazi, Abdelghani; Chahdi, Hafsa; Guelzim, Khalid; Kouach, Jaouad; Babahabib, Myabdellah; Elhassani, Myehdi; Rahali, Driss Moussaoui; Dehayni, Mohammed

2015-01-01

Le carcinome à cellule vitreuse du col de l'utérus est un type de histologique rare de cancer du col de l'utérus qui survient à un âge plus jeune, et s'associe au risque élevé d’échec thérapeutique et le pronostic est plus mauvais en comparaison au type cellulaire squameux. La radiothérapie est associée au risque diminué de récidive. Le but de cette étude est de récapituler à travers d'une observation et une revue de littérature les données sur l'incidence, le comportement clinique et la survie globale de patients avec le carcinome à cellule vitreuse du col de l'utérus. PMID:26664556

A Case for Thinking Without Consciousness.

PubMed

Dijksterhuis, Ap; Strick, Madelijn

2016-01-01

People can engage in prolonged thought processes, such as when they are facing an important decision or when they are working on a scientific discovery. Such thought processes can take months or even years. We argue that while people engage in such thinking, they make progress not only when they consciously think but also sometimes when they are consciously thinking about something else-that is, while they think unconsciously. We review the literature on unconscious thought (UT) processes and conclude that there is indeed quite some evidence for UT. Conceptualized as a form of unconscious goal pursuit, UT is likely to be especially fruitful for thought processes that are complex, important, or interesting to the thinker. In addition, we discuss other characteristics of the UT process. We end with proposing Type 3 processes, in addition to Type 1 and Type 2 (or Systems 1 and 2) processes, to accommodate prolonged thought processes in models on thought. © The Author(s) 2015.

Microstructure evolution and mechanical properties of nano-SiCp/AZ91 composite processed by extrusion and equal channel angular pressing (ECAP)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Qiao, X.G.; Ying, T.

Nano-SiCp/AZ91 magnesium matrix composite was fabricated by stir casting. The as-cast ingots were extruded at 350 °C, then processed by equal channel angular pressing (ECAP) at various temperatures (250 °C, 300 °C and 350 °C). Grains are significantly refined after the extrusion and the ECAP. A basal fibre texture was detected by neutron diffraction after the extrusion, which inclines about 45° to the extrusion direction (ED) after the ECAP. Nano-scaled SiC particles agglomerate in the as-cast composite. After the extrusion, the agglomeration tends to form continuous or discontinuous strips along the extrusion direction. By application of the ECAP, the agglomeratedmore » SiC particles are partly dispersed and the strips formed during the extrusion tend to be thinner and broken with the increasing pass number. The yield tensile strength (YTS) and the ultimate tensile strength (UTS) of the composite are dramatically increased after the extrusion. ECAP for one pass at various temperatures further increases the strength, however, the YTS decreases with the increasing ECAP temperature and the pass number. The Orowan equations predict the maximum YTS of the composite may be up to 400 MPa providing SiC particles are homogenously distributed in the matrix. - Highlights: •Nano-scaled SiC particles were successfully added into AZ91 by stirring casting. •Agglomeration of nano-particles were improved by extrusion and ECAP. •Yield strength of the composite is 328 MPa after one pass of ECAP. •Further ECAP process with optimized parameters may fully disperse nano-particles. •Yield strength is predicted to up to 400 MPa when particles are fully dispersed.« less

A university system's approach to enhancing the educational mission of health science schools and institutions: the University of Texas Academy of Health Science Education

PubMed Central

Buja, L. Maximilian; Cox, Susan M.; Lieberman, Steven A.; MacClements, Jonathan; Williams, Janet F.; Esterl, Robert M.; Shine, Kenneth I.

2013-01-01

Background The academy movement developed in the United States as an important approach to enhance the educational mission and facilitate the recognition and work of educators at medical schools and health science institutions. Objectives Academies initially formed at individual medical schools. Educators and leaders in The University of Texas System (the UT System, UTS) recognized the academy movement as a means both to address special challenges and pursue opportunities for advancing the educational mission of academic health sciences institutions. Methods The UTS academy process was started by the appointment of a Chancellor's Health Fellow for Education in 2004. Subsequently, the University of Texas Academy of Health Science Education (UTAHSE) was formed by bringing together esteemed faculty educators from the six UTS health science institutions. Results Currently, the UTAHSE has 132 voting members who were selected through a rigorous, system-wide peer review and who represent multiple professional backgrounds and all six campuses. With support from the UTS, the UTAHSE has developed and sustained an annual Innovations in Health Science Education conference, a small grants program and an Innovations in Health Science Education Award, among other UTS health science educational activities. The UTAHSE represents one university system's innovative approach to enhancing its educational mission through multi- and interdisciplinary as well as inter-institutional collaboration. Conclusions The UTAHSE is presented as a model for the development of other consortia-type academies that could involve several components of a university system or coalitions of several institutions. PMID:23490406

Treatment patterns in hyperlipidaemia patients based on administrative claim databases in Japan.

PubMed

Wake, Mayumi; Onishi, Yoshie; Guelfucci, Florent; Oh, Akinori; Hiroi, Shinzo; Shimasaki, Yukio; Teramoto, Tamio

2018-05-01

Real-world evidence on treatment of hyperlipidaemia (HLD) in Japan is limited. We aimed to describe treatment patterns, persistence with, and adherence to treatment in Japanese patients with HLD. Retrospective analyses of adult HLD patients receiving drug therapy in 2014-2015 were conducted using the Japan Medical Data Center (JMDC) and Medical Data Vision (MDV) databases. Depending on their HLD treatment history, individuals were categorised as untreated (UT) or previously treated (PT), and were followed for at least 12 months. Outcomes of interest included prescribing patterns of HLD drug classes, persistence with treatment at 12 months, and adherence to treatment. Data for 49,582 and 53,865 patients from the JMDC and MDV databases, respectively, were analysed. First-line HLD prescriptions for UT patients were predominantly for moderate statins (JMDC: 75.9%, MDV: 77.0%). PT patients most commonly received combination therapy (JMDC: 43.9%, MDV: 52.6%). Approximately half of the UT patients discontinued treatment during observation. Within each cohort, persistence rates were lower in UT patients than in PT patients (JMDC: 45.0% vs. 77.5%; MDV: 51.9% vs. 85.3%). Adherence was ≥80% across almost all HLD drug classes, and was slightly lower in the JMDC cohort than MDV cohort. Most common prescriptions were moderate statins in UT patients and combination therapy in PT patients. The high discontinuation rate of HLD therapy in UT patients warrants further investigation and identification of methods to encourage and support long-term persistence. Copyright © 2018. Published by Elsevier B.V.

Metformin, an AMPK activator, stimulates the phosphorylation of aquaporin 2 and urea transporter A1 in inner medullary collecting ducts.

PubMed

Klein, Janet D; Wang, Yanhua; Blount, Mitsi A; Molina, Patrick A; LaRocque, Lauren M; Ruiz, Joseph A; Sands, Jeff M

2016-05-15

Nephrogenic diabetes insipidus (NDI) is characterized by production of very large quantities of dilute urine due to an inability of the kidney to respond to vasopressin. Congenital NDI results from mutations in the type 2 vasopressin receptor (V2R) in ∼90% of families. These patients do not have mutations in aquaporin-2 (AQP2) or urea transporter UT-A1 (UT-A1). We tested adenosine monophosphate kinase (AMPK) since it is known to phosphorylate another vasopressin-sensitive transporter, NKCC2 (Na-K-2Cl cotransporter). We found AMPK expressed in rat inner medulla (IM). AMPK directly phosphorylated AQP2 and UT-A1 in vitro. Metformin, an AMPK activator, increased phosphorylation of both AQP2 and UT-A1 in rat inner medullary collecting ducts (IMCDs). Metformin increased the apical plasma membrane accumulation of AQP2, but not UT-A1, in rat IM. Metformin increased both osmotic water permeability and urea permeability in perfused rat terminal IMCDs. These findings suggest that metformin increases osmotic water permeability by increasing AQP2 accumulation in the apical plasma membrane but increases urea permeability by activating UT-A1 already present in the membrane. Lastly, metformin increased urine osmolality in mice lacking a V2R, a mouse model of congenital NDI. We conclude that AMPK activation by metformin mimics many of the mechanisms by which vasopressin increases urine-concentrating ability. These findings suggest that metformin may be a novel therapeutic option for congenital NDI due to V2R mutations. Copyright © 2016 the American Physiological Society.

Metformin, an AMPK activator, stimulates the phosphorylation of aquaporin 2 and urea transporter A1 in inner medullary collecting ducts

PubMed Central

Wang, Yanhua; Blount, Mitsi A.; Molina, Patrick A.; LaRocque, Lauren M.; Ruiz, Joseph A.

2016-01-01

Nephrogenic diabetes insipidus (NDI) is characterized by production of very large quantities of dilute urine due to an inability of the kidney to respond to vasopressin. Congenital NDI results from mutations in the type 2 vasopressin receptor (V2R) in ∼90% of families. These patients do not have mutations in aquaporin-2 (AQP2) or urea transporter UT-A1 (UT-A1). We tested adenosine monophosphate kinase (AMPK) since it is known to phosphorylate another vasopressin-sensitive transporter, NKCC2 (Na-K-2Cl cotransporter). We found AMPK expressed in rat inner medulla (IM). AMPK directly phosphorylated AQP2 and UT-A1 in vitro. Metformin, an AMPK activator, increased phosphorylation of both AQP2 and UT-A1 in rat inner medullary collecting ducts (IMCDs). Metformin increased the apical plasma membrane accumulation of AQP2, but not UT-A1, in rat IM. Metformin increased both osmotic water permeability and urea permeability in perfused rat terminal IMCDs. These findings suggest that metformin increases osmotic water permeability by increasing AQP2 accumulation in the apical plasma membrane but increases urea permeability by activating UT-A1 already present in the membrane. Lastly, metformin increased urine osmolality in mice lacking a V2R, a mouse model of congenital NDI. We conclude that AMPK activation by metformin mimics many of the mechanisms by which vasopressin increases urine-concentrating ability. These findings suggest that metformin may be a novel therapeutic option for congenital NDI due to V2R mutations. PMID:26962099

Ionospheric Anomalies Related to the (M = 7.3), August 27, 2012, Puerto Earthquake, (M = 6.8), August 30, 2012 Jan Mayen Island Earthquake, and (M = 7.6), August 31, 2012, Philippines Earthquake: Two-Dimensional Principal Component Analysis

PubMed Central

Lin, Jyh-Woei

2013-01-01

Two-dimensional principal component analysis (2DPCA) and principal component analysis (PCA) are used to examine the ionospheric total electron content (TEC) data during the time period from 00:00 on August 21 to 12: 45 on August 31 (UT), which are 10 days before the M = 7.6 Philippines earthquake at 12:47:34 on August 31, 2012 (UT) with the depth at 34.9 km. From the results by using 2DPCA, a TEC precursor of Philippines earthquake is found during the time period from 4:25 to 4:40 on August 28, 2012 (UT) with the duration time of at least 15 minutes. Another earthquake-related TEC anomaly is detectable for the time period from 04:35 to 04:40 on August 27, 2012 (UT) with the duration time of at least 5 minutes during the Puerto earthquake at 04: 37:20 on August 27, 2012 (UT) (M w = 7.3) with the depth at 20.3 km. The precursor of the Puerto earthquake is not detectable. TEC anomaly is not to be found related to the Jan Mayen Island earthquake (M w = 6.8) at 13:43:24 on August 30, 2012 (UT). These earthquake-related TEC anomalies are detectable by using 2DPCA rather than PCA. They are localized nearby the epicenters of the Philippines and Puerto earthquakes. PMID:23844386

RadNet Air Data From St. George, UT

EPA Pesticide Factsheets

This page presents radiation air monitoring and air filter analysis data for St. George, UT from EPA's RadNet system. RadNet is a nationwide network of monitoring stations that measure radiation in air, drinking water and precipitation.

INTERSECTION OF 445 NORTH & 1040 EAST, SALT LAKE CITY, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERSECTION OF 445 NORTH & 1040 EAST, SALT LAKE CITY, UT. VIEW LOOKING SOUTH. REPHOTOGRAPH OF HISTORIC SHIPLER PHOTO # 18272, UTAH STATE HISTORICAL SOCIETY COLLECTION. - Salt Lake City Cemetery, 200 N Street, Salt Lake City, Salt Lake County, UT

Nonpeptidic urotensin-II receptor antagonists I: in vitro pharmacological characterization of SB-706375

PubMed Central

Douglas, Stephen A; Behm, David J; Aiyar, Nambi V; Naselsky, Diane; Disa, Jyoti; Brooks, David P; Ohlstein, Eliot H; Gleason, John G; Sarau, Henry M; Foley, James J; Buckley, Peter T; Schmidt, Dulcie B; Wixted, William E; Widdowson, Katherine; Riley, Graham; Jin, Jian; Gallagher, Timothy F; Schmidt, Stanley J; Ridgers, Lance; Christmann, Lisa T; Keenan, Richard M; Knight, Steven D; Dhanak, Dashyant

2005-01-01

SB-706375 potently inhibited [125I]hU-II binding to both mammalian recombinant and ‘native' UT receptors (Ki 4.7±1.5 to 20.7±3.6 nM at rodent, feline and primate recombinant UT receptors and Ki 5.4±0.4 nM at the endogenous UT receptor in SJRH30 cells). Prior exposure to SB-706375 (1 μM, 30 min) did not alter [125I]hU-II binding affinity or density in recombinant cells (KD 3.1±0.4 vs 5.8±0.9 nM and Bmax 3.1±1.0 vs 2.8±0.8 pmol mg−1) consistent with a reversible mode of action. The novel, nonpeptidic radioligand [3H]SB-657510, a close analogue of SB-706375, bound to the monkey UT receptor (KD 2.6±0.4 nM, Bmax 0.86±0.12 pmol mg−1) in a manner that was inhibited by both U-II isopeptides and SB-706375 (Ki 4.6±1.4 to 17.6±5.4 nM) consistent with the sulphonamides and native U-II ligands sharing a common UT receptor binding domain. SB-706375 was a potent, competitive hU-II antagonist across species with pKb 7.29–8.00 in HEK293-UT receptor cells (inhibition of [Ca2+]i-mobilization) and pKb 7.47 in rat isolated aorta (inhibition of contraction). SB-706375 also reversed tone established in the rat aorta by prior exposure to hU-II (Kapp∼20 nM). SB-706375 was a selective U-II antagonist with ⩾100-fold selectivity for the human UT receptor compared to 86 distinct receptors, ion channels, enzymes, transporters and nuclear hormones (Ki/IC50>1 μM). Accordingly, the contractile responses induced in isolated aortae by KCl, phenylephrine, angiotensin II and endothelin-1 were unaltered by SB-706375 (1 μM). In summary, SB-706375 is a high-affinity, surmountable, reversible and selective nonpeptide UT receptor antagonist with cross-species activity that will assist in delineating the pathophysiological actions of U-II in mammals. PMID:15852036

Cluster Observations of reconnection along the dusk flank of the magnetosphere

NASA Astrophysics Data System (ADS)

Escoubet, C.-Philippe; Grison, Benjamin; Berchem, Jean; Trattner, Karlheinz; Lavraud, Benoit; Pitout, Frederic; Soucek, Jan; Richard, Robert; Laakso, Harri; Masson, Arnaud; Dunlop, Malcolm; Dandouras, Iannis; Reme, Henri; Fazakerley, Andrew; Daly, Patrick

2015-04-01

Magnetic reconnection is generally accepted to be the main process that transfers particles and energy from the solar wind to the magnetosphere. The location of the reconnection site depends on the orientation of the interplanetary magnetic field (IMF) in the solar wind: on the dayside magnetosphere for an IMF southward, on the lobes for an IMF northward and on the flanks for an IMF in the East-West direction. Since most of observations of reconnection events have sampled a limited region of space simultaneously it is still not yet know if the reconnection line is extended over large regions of the magnetosphere or if is patchy and made of many reconnection lines. We report a Cluster crossing on 5 January 2002 near the exterior cusp on the southern dusk side where we observe multiple sources of reconnection/injections. The IMF was mainly azimuthal (IMF-By around -5 nT), the solar wind speed lower than usual around 280 km/s with the density of order 5 cm-3. The four Cluster spacecraft had an elongated configuration near the magnetopause. C4 was the first spacecraft to enter the cusp around 19:52:04 UT, followed by C2 at 19:52:35 UT, C1 at 19:54:24 UT and C3 at 20:13:15 UT. C4 and C1 observed two ion energy dispersions at 20:10 UT and 20:40 UT and C3 at 20:35 UT and 21:15 UT. Using the time of flight technique on the upgoing and downgoing ions, which leads to energy dispersions, we obtain distances of the ion sources between 14 and 20 RE from the spacecraft. The slope of the ion energy dispersions confirmed these distances. Using Tsyganenko model, we find that these sources are located on the dusk flank, past the terminator. The first injection by C3 is seen at approximately the same time as the 2nd injection on C1 but their sources at the magnetopause were separated by more than 7 RE. This would imply that two distinct sources were active at the same time on the dusk flank of the magnetosphere. In addition, a flow reversal was observed at the magnetopause on C4 which would be an indication that reconnection is also taking place near the exterior cusp quasi-simultaneously.

Local over-expression of VEGF-DΔNΔC in the uterine arteries of pregnant sheep results in long-term changes in uterine artery contractility and angiogenesis.

PubMed

Mehta, Vedanta; Abi-Nader, Khalil N; Shangaris, Panicos; Shaw, S W Steven; Filippi, Elisa; Benjamin, Elizabeth; Boyd, Michael; Peebles, Donald M; Martin, John; Zachary, Ian; David, Anna L

2014-01-01

The normal development of the uteroplacental circulation in pregnancy depends on angiogenic and vasodilatory factors such as vascular endothelial growth factor (VEGF). Reduced uterine artery blood flow (UABF) is a common cause of fetal growth restriction; abnormalities in angiogenic factors are implicated. Previously we showed that adenovirus (Ad)-mediated VEGF-A165 expression in the pregnant sheep uterine artery (UtA) increased nitric oxide synthase (NOS) expression, altered vascular reactivity and increased UABF. VEGF-D is a VEGF family member that promotes angiogenesis and vasodilatation but, in contrast to VEGF-A, does not increase vascular permeability. Here we examined the effect of Ad.VEGF-DΔNΔC vector encoding a fully processed form of VEGF-D, on the uteroplacental circulation. UtA transit-time flow probes and carotid artery catheters were implanted in mid-gestation pregnant sheep (n = 5) to measure baseline UABF and maternal haemodynamics respectively. 7-14 days later, after injection of Ad.VEGF-DΔNΔC vector (5×10(11) particles) into one UtA and an Ad vector encoding β-galactosidase (Ad.LacZ) contralaterally, UABF was measured daily until scheduled post-mortem examination at term. UtAs were assessed for vascular reactivity, NOS expression and endothelial cell proliferation; NOS expression was studied in ex vivo transduced UtA endothelial cells (UAECs). At 4 weeks post-injection, Ad.VEGF-DΔNΔC treated UtAs showed significantly lesser vasoconstriction (Emax144.0 v/s 184.2, p = 0.002). There was a tendency to higher UABF in Ad.VEGF-DΔNΔC compared to Ad.LacZ transduced UtAs (50.58% v/s 26.94%, p = 0.152). There was no significant effect on maternal haemodynamics. An increased number of proliferating endothelial cells and adventitial blood vessels were observed in immunohistochemistry. Ad.VEGF-DΔNΔC expression in cultured UAECs upregulated eNOS and iNOS expression. Local over-expression of VEGF-DΔNΔC in the UtAs of pregnant mid-gestation sheep reduced vasoconstriction, promoted endothelial cell proliferation and showed a trend towards increased UABF. Studies in cultured UAECs indicate that VEGF-DΔNΔC may act in part through upregulation of eNOS and iNOS.

Tropical upper troposphere and tropopause layer in situ measurement of H2O by the micro- SDLA balloon borne diode laser spectrometer: modelling interpretation.

NASA Astrophysics Data System (ADS)

Durry, G.; Huret, N.; Freitas, S.; Hauchecorne, A.; Longo, K.

2006-12-01

During the HIBISCUS European campaign in Bauru (Brazil, 22°S) in 2004, the micro-SDLA diode laser sensor was flown twice on February the 13th (SF2 flight) and the 24th (SF4 flight) from small size open stratospheric balloons operated by the CNES. In situ measurements of H2O, CH4 at high spatial resolution (a few meters) were obtained in the UT and in the TTL. Both flights took place in convective conditions. Layering in the TTL water vapour content is observed with values from 3 ppmv (typical of TTL) to high values of 6 ppmv. To investigate such layering we have used a combination of 3D trajectory calculations (Freitas et al., JGR, 2000) using the mesoscale model BRAMS outputs and Potential vorticity map obtained from the high- resolution PV-advection model MIMOSA (Hauchecorne et al., JGR, 2001). The mesoscale model BRAMS allows us to study processes associated with convective systems, whereas isentropic transport at global scale is investigated with MIMOSA. Backward 3D trajectories have been calculated every km for the two flights. It appears that a very strong uplifting from the ground to 16.5 km has occurred 80 hours before the SF4 flight. This uplifting is associated with a 3 ppmv water vapor layer whereas just above twice more water vapour is observed. This layer with high water vapor is associated with trajectories that skim over the top of the convective region. This leads us to discuss on the ability of convective system to inject water vapour in the TTL. For both flights we investigate also the impact of isentropic transport from extratropical region on TTL water vapour content. It appears that for the SF2 and SF4 flight using the PV maps from MIMOSA model we report filamentation in the TTL and in the UT respectively. This filamentation is associated in the UT with strong dehydration observed at 8-10 km for the SF4 flight and with high water vapour content in the TTL typical of mid- latitude region during SF2 flight.

RadNet Air Data From Salt Lake City, UT

EPA Pesticide Factsheets

This page presents radiation air monitoring and air filter analysis data for Salt Lake City, UT from EPA's RadNet system. RadNet is a nationwide network of monitoring stations that measure radiation in air, drinking water and precipitation.

Studies of Ionospheric Processes in the Atmosphere and the Laboratory

DTIC Science & Technology

2006-06-01

relevance to HAARP observations, and on vibrationally-excited levels of the O2 ground state [2] and the b1Σ +g excited state [3]. Synergy with the...UT [20] 29.4 (33) 260 0.94 .077 3/24/95 1737 UT 43.4 (44) 278 0.54 0.53 HAARP 62N, 145W 3/20/04 0617 UT [21] 54 (44) 290 0.33 0.54... HAARP 0.62 5.0E8 1.09E8 4.6 Studies of Ionospheric Processes in the Atmosphere and the Laboratory RTO-MP-IST-056 1 - 9 UNCLASSIFIED/UNLIMITED

Systems Engineering Body of Knowledge and Its Integration with Software Engineering

DTIC Science & Technology

2011-05-01

e pro ess ona  soc e es  y  end of 2012. 801/27/2010 4/25/2011 9 Topic 2 (Article Title)Part 1 Related Topics Article Structure Lorem ipsum dolor  sit...amet[1], consectetuer adipiscing elit, sed diam nonummy nibh euismod tincidunt ut laoreet dolore magna aliquam erat volutpat. Ut wisi enim ad minim...veniam, quis nostrud exerci tation ullamcorper suscipit lobortis nisl ut aliquip ex ea commodo consequat. Duis autem vel eum iriure dolor [2] in

Can flavonoid-rich chocolate modulate arterial elasticity and pathological uterine artery Doppler blood flow in pregnant women? A pilot study.

PubMed

von Wowern, Emma; Olofsson, Per

2018-09-01

Dark chocolate has shown beneficial effects on cardiovascular health and might also modulate hypertensive complications in pregnancy and uteroplacental blood flow. Increased uteroplacental resistance is associated with systemic arterial stiffness. We aimed to investigate the short-term effect of flavonoid-rich chocolate on arterial stiffness and Doppler blood flow velocimetry indexes in pregnant women with compromised uteroplacental blood flow. Doppler blood flow velocimetry and digital pulse wave analysis (DPA) were performed in 25 women pregnant in the second and third trimesters with uterine artery (UtA) score (UAS) 3-4, before and after 3 days of ingestion of chocolate with high flavonoid and antioxidant contents. UtA pulsatility index (PI), UtA diastolic notching, UAS (semiquantitative measure of PI and notching combined), and umbilical artery PI were calculated, and DPA variables representing central and peripheral maternal arteries were recorded. Mean UtA PI (p = .049) and UAS (p = .025) significantly decreased after chocolate consumption. There were no significant changes in UtA diastolic notching or any DPA indexes of arterial stiffness/vascular tone. Chocolate may have beneficial effects on the uteroplacental circulation, but in this pilot study, we could not demonstrate effects on arterial vascular tone as assessed by DPA.

Breakout Reconnection Observed by the TESIS EUV Telescope

NASA Astrophysics Data System (ADS)

Reva, A. A.; Ulyanov, A. S.; Shestov, S. V.; Kuzin, S. V.

2016-01-01

We present experimental evidence of the coronal mass ejection (CME) breakout reconnection, observed by the TESIS EUV telescope. The telescope could observe solar corona up to 2 R⊙ from the Sun center in the Fe 171 Å line. Starting from 2009 April 8, TESIS observed an active region (AR) that had a quadrupolar structure with an X-point 0.5 R⊙ above photosphere. A magnetic field reconstructed from the Michelson Doppler Imager data also has a multipolar structure with an X-point above the AR. At 21:45 UT on April 9, the loops near the X-point started to move away from each other with a velocity of ≈7 km s-1. At 01:15 UT on April 10, a bright stripe appeared between the loops, and the flux in the GOES 0.5-4 Å channel increased. We interpret the loops’ sideways motion and the bright stripe as evidence of the breakout reconnection. At 01:45 UT, the loops below the X-point started to slowly move up. At 15:10 UT, the CME started to accelerate impulsively, while at the same time a flare arcade formed below the CME. After 15:50 UT, the CME moved with constant velocity. The CME evolution precisely followed the breakout model scenario.

Influence of fatigue and velocity on the latency and recruitment order of scapular muscles.

PubMed

Mendez-Rebolledo, Guillermo; Gatica-Rojas, Valeska; Guzman-Muñoz, Eduardo; Martinez-Valdes, Eduardo; Guzman-Venegas, Rodrigo; Berral de la Rosa, Francisco Jose

2018-07-01

To determine the influence of velocity and fatigue on scapular muscle activation latency and recruitment order during a voluntary arm raise task, in healthy individuals. Cross-sectional study. University laboratory. Twenty three male adults per group (high-velocity and low-velocity). Onset latency of scapular muscles [Anterior deltoid (AD), lower trapezius (LT), middle trapezius (MT), upper trapezius (UT), and serratus anterior (SA)] was assessed by surface electromyography. The participants were assigned to one of two groups: low-velocity or high-velocity. Both groups performed a voluntary arm raise task in the scapular plane under two conditions: no-fatigue and fatigue. The UT showed early activation (p < 0.01) in the fatigue condition when performing the arm raise task at a high velocity. At a low velocity and with no muscular fatigue, the recruitment order was MT, LT, SA, AD, and UT. However, the recruitment order changed in the high-velocity with muscular fatigue condition, since the recruitment order was UT, AD, SA, LT, and MT. The simultaneous presence of fatigue and high-velocity in an arm raise task is associated with a decrease in the UT activation latency and a modification of the recruitment order of scapular muscles. Copyright © 2018 Elsevier Ltd. All rights reserved.

A Randomized Multicenter Clinical Trial of Ultrathin Descemet Stripping Automated Endothelial Keratoplasty (DSAEK) versus DSAEK.

PubMed

Dickman, Mor M; Kruit, Pieter J; Remeijer, Lies; van Rooij, Jeroen; Van der Lelij, Allegonda; Wijdh, Robert H J; van den Biggelaar, Frank J H M; Berendschot, Tos T J M; Nuijts, Rudy M M A

2016-11-01

To compare visual acuity, refraction, endothelial cell density (ECD), and complications after Descemet stripping automated endothelial keratoplasty (DSAEK) and ultrathin DSAEK (UT-DSAEK). A multicenter, prospective, double-masked, randomized, controlled clinical trial. From 66 patients with irreversible corneal endothelial dysfunction dues to Fuchs' dystrophy who enrolled from 4 tertiary medical centers in the Netherlands, 66 eyes were studied. Participants were centrally randomized to undergo either UT-DSAEK or DSAEK, based on preoperative best spectacle-corrected visual acuity (BSCVA), recipient central corneal thickness, patient age, and recruitment center. Donor corneas were precut by a single cornea bank. Participants underwent ophthalmic examinations preoperatively and 3, 6, and 12 months after the operation, including manifest refraction, BSCVA using an Early Treatment Diabetic Retinopathy Study chart, and endothelium imaging. BSCVA 12 months postoperatively. Preoperative BSCVA did not differ between patients undergoing DSAEK (0.35 logarithm of the minimum angle of resolution [logMAR] [95% confidence interval {CI} 0.27-0.43]; n = 32) and UT-DSAEK (0.37 logMAR [95% CI 0.31-0.43]; n = 34; P = 0.8). BSCVA was significantly better after UT-DSAEK compared with that after DSAEK at 3 months (0.17 logMAR [95% CI 0.13-0.21], n = 31 vs. 0.28 logMAR [95% CI 0.23-0.33], n = 31; P = 0.001), 6 months (0.14 logMAR [95% CI 0.10-0.18], n = 30 vs. 0.24 logMAR [95% CI 0.20-0.28], n = 30; P = 0.002), and 12 months (0.13 logMAR [95% CI 0.09-0.17], n = 33 vs. 0.20 logMAR [95% CI 0.15-0.25], n = 29; P = 0.03). Refraction, ECD loss (40% at 3 months; P < 0.001), donor loss (DSAEK n = 2 vs. UT-DSAEK n = 3 [relative risk {RR} 1.4 {95% CI 0.24-7.5}; P = 0.7]), and graft dislocation (DSAEK n = 5 vs. UT-DSAEK n = 5 [RR 1.0 {95% CI 0.34-3.33}; P = 0.9]) did not differ between UT-DSAEK and DSAEK. Donor thickness was significantly thinner for UT-DSAEK (101 μm [95% CI 93-110 μm]; range 50-145 μm) than for DSAEK (209 μm [95% CI 196-222 μm]; range 147-289 μm; P < 0.001). This study indicates that compared with DSAEK, UT-DSAEK results in faster and better recovery of BSCVA with similar refractive outcomes, endothelial cell loss, and incidence of complications. Copyright © 2016 American Academy of Ophthalmology. Published by Elsevier Inc. All rights reserved.

Analyzing Commodity Council Development and Implementation: The Air Force Furnishings Commodity Council

DTIC Science & Technology

2011-12-01

all production carried on by one big firm? … First, as a firm gets larger, there may be decreasing returns to the entrepreneur function, that is, the...the entrepreneur fails to place the factors of production in the uses where their value is greatest, that is, fails to make the best use of the...three one-week classroom modules. UT coordinated with AFFCC to ensure team members received the module training at a specific point during the strategy

Reference Values of Grip Strength, Prevalence of Low Grip Strength, and Factors Affecting Grip Strength Values in Chinese Adults.

PubMed

Yu, Ruby; Ong, Sherlin; Cheung, Osbert; Leung, Jason; Woo, Jean

2017-06-01

The objectives of this study were to update the reference values of grip strength, to estimate the prevalence of low grip strength, and to examine the impact of different aspects of measurement protocol on grip strength values in Chinese adults. A cross-sectional survey of Chinese men (n = 714) and women (n = 4014) aged 18-102 years was undertaken in different community settings in Hong Kong. Grip strength was measured with a digital dynamometer (TKK 5401 Grip-D; Takei, Niigata, Japan). Low grip strength was defined as grip strength 2 standard deviations or more below the mean for young adults. The effects of measurement protocol on grip strength values were examined in a subsample of 45 men and women with repeated measures of grip strength taken with a hydraulic dynamometer (Baseline; Fabrication Enterprises Inc, Irvington, NY), using pair t-tests, intraclass correlation coefficient, and Bland and Altman plots. Grip strength was greater among men than among women (P < .001) and the rate of decline differed between sexes (P < .001). The prevalence of low grip strength also increased with age, reaching a rate of 16.5% in men and 20.6% in women aged 65+. Although the TKK digital dynamometer gave higher grip strength values than the Baseline hydraulic dynamometer (P < .001), the degree of agreement between the 2 dynamometers was satisfactory. Higher grip strength values were also observed when the measurement was performed with the elbow extended in a standing position, compared with that with the elbow flexed at 90° in a sitting position, using the same dynamometer (P < .05). This study updated the reference values of grip strength and estimated the prevalence of low grip strength among Chinese adults spanning a wide age range. These findings might be useful for risk estimation and evaluation of interventions. However, grip strength measurements should be interpreted with caution, as grip strength values can be affected by type of dynamometer used, assessment posture, and elbow position. Copyright © 2017 AMDA – The Society for Post-Acute and Long-Term Care Medicine. Published by Elsevier Inc. All rights reserved.

CHINESE PLAT, 1919 (L19 19 4 E, SALT LAKE CITY ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

CHINESE PLAT, 1919 (L19 19 4 E, SALT LAKE CITY CEMETERY LOCATER), SALT LAKE CITY, UT. VIEW LOOKING NORTHEAST AT CHINESE PLAT MARKER AND BURNER. - Salt Lake City Cemetery, 200 N Street, Salt Lake City, Salt Lake County, UT

Simple Event | Center for Cancer Research

Cancer.gov

Morbi lobortis urna et posuere interdum. Fusce vulputate finibus magna et molestie. Fusce consequat, sapien a euismod vestibulum, nisl quam hendrerit quam, vitae finibus tellus orci viverra lacus. Donec condimentum purus ut fermentum egestas. Praesent tempus ligula ut ipsum tempus, eu ullamcorper arcu fringilla.

Role of IMF B y in the prompt electric field disturbances over equatorial ionosphere during a space weather event

DOE PAGES

Chakrabarty, Dipu; Hui, Debrup; Rout, Diptiranjan; ...

2017-02-04

On 7 January 2005 (Ap=40) prompt penetration electric field perturbations of opposite polarities were observed over Thumba and Jicamarca on a few occasions during 13:45–16:30 UT. However, the electric field was found to be eastward during 14:45–15:30 UT over both Thumba and Jicamarca contrary to the general expectation wherein opposite polarities are expected at nearly antipodal points. On closer scrutiny, three important observational features are noticed during 14:10–15:15 UT. First, during 14:10–14:45 UT, despite increasing southward interplanetary magnetic field (IMF) B z condition, the already westward electric field over Thumba weakened (less westward) while the eastward electric field over Jicamarcamore » intensified (more eastward). Second, the electric field not only became anomalously eastward over Thumba but also got intensified further during 14:45–15:00 UT similar to Jicamarca. Third, during 15:00–15:15 UT, despite IMF B z remaining steadily southward, the eastward electric field continued to intensify over Thumba but weakened over Jicamarca. It is suggested that the changes in IMF B y component under southward IMF B z condition are responsible for skewing the ionospheric equipotential patterns over the dip equator in such a way that Thumba came into the same DP2 cell as that of Jicamarca leading to anomalous electric field variations. Magnetic field measurements along the Indian and Jicamarca longitude sectors and changes in high-latitude ionospheric convection patterns provide credence to this proposition. Therefore, in conclusion, the present investigation shows that the variations in IMF B y are fundamentally important to understand the prompt penetration effects over low latitudes.« less

Comparison between transdermal nitroglycerin and sildenafil citrate in intrauterine growth restriction: effects on uterine, umbilical and fetal middle cerebral artery pulsatility indices.

PubMed

Trapani, A; Gonçalves, L F; Trapani, T F; Franco, M J; Galluzzo, R N; Pires, M M S

2016-07-01

To evaluate the effects of transdermal nitroglycerin (GTN) and sildenafil citrate on Doppler velocity waveforms of the uterine (UtA), umbilical (UA) and fetal middle cerebral (MCA) arteries in pregnancies with intrauterine growth restriction (IUGR). This was a prospective study of 35 singleton pregnancies (gestational age, 24-31 weeks) with IUGR and abnormal UtA and UA Doppler waveforms. We compared maternal arterial blood pressure and Z-scores of the pulsatility index (PI) of UtA, UA and fetal MCA before and after application of a transdermal GTN patch (average dose, 0.4 mg/h), oral sildenafil citrate (50 mg) or placebo. Statistical analysis was performed by ANOVA for paired samples. There was a significant decrease in UtA-PI after application of GTN (21.0%) and sildenafil citrate (20.4%). A significant reduction in UA-PI was also observed for both GTN (19.1%) and sildenafil citrate (18.2%). There was no difference in UtA- and UA-PI when the GTN and sildenafil groups were compared. No changes in Doppler velocimetry were observed in the placebo group and no significant change in MCA-PI was observed in any group. Maternal arterial blood pressure decreased with administration of both GTN and sildenafil citrate in those with pre-eclampsia. The use of transdermal GTN or sildenafil citrate in pregnancies with IUGR is associated with a significant reduction in both UtA and UA Doppler PI, as well as maternal arterial blood pressure. Neither drug affected the MCA-PI. Copyright © 2015 ISUOG. Published by John Wiley & Sons Ltd. Copyright © 2015 ISUOG. Published by John Wiley & Sons Ltd.

Role of IMF B y in the prompt electric field disturbances over equatorial ionosphere during a space weather event

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chakrabarty, Dipu; Hui, Debrup; Rout, Diptiranjan

On 7 January 2005 (Ap=40) prompt penetration electric field perturbations of opposite polarities were observed over Thumba and Jicamarca on a few occasions during 13:45–16:30 UT. However, the electric field was found to be eastward during 14:45–15:30 UT over both Thumba and Jicamarca contrary to the general expectation wherein opposite polarities are expected at nearly antipodal points. On closer scrutiny, three important observational features are noticed during 14:10–15:15 UT. First, during 14:10–14:45 UT, despite increasing southward interplanetary magnetic field (IMF) B z condition, the already westward electric field over Thumba weakened (less westward) while the eastward electric field over Jicamarcamore » intensified (more eastward). Second, the electric field not only became anomalously eastward over Thumba but also got intensified further during 14:45–15:00 UT similar to Jicamarca. Third, during 15:00–15:15 UT, despite IMF B z remaining steadily southward, the eastward electric field continued to intensify over Thumba but weakened over Jicamarca. It is suggested that the changes in IMF B y component under southward IMF B z condition are responsible for skewing the ionospheric equipotential patterns over the dip equator in such a way that Thumba came into the same DP2 cell as that of Jicamarca leading to anomalous electric field variations. Magnetic field measurements along the Indian and Jicamarca longitude sectors and changes in high-latitude ionospheric convection patterns provide credence to this proposition. Therefore, in conclusion, the present investigation shows that the variations in IMF B y are fundamentally important to understand the prompt penetration effects over low latitudes.« less

The overall computer/mobile devices usage time is related to newly diagnosed non-alcoholic fatty liver disease: a population-based study.

PubMed

Meng, Ge; Liu, Fangfang; Fang, Liyun; Li, Chunlei; Zhang, Qing; Liu, Li; Wu, Hongmei; Du, Huanmin; Shi, Hongbin; Xia, Yang; Guo, Xiaoyan; Liu, Xing; Bao, Xue; Su, Qian; Gu, Yeqing; Yu, Fei; Yang, Huijun; Yu, Bin; Sun, Shaomei; Wang, Xing; Zhou, Ming; Jia, Qiyu; Guo, Qi; Chen, Xin; Song, Kun; Wang, Guolin; Huang, Guowei; Niu, Kaijun

2016-11-01

The computer/mobile devices usage time (CMD-UT) is closely related to a sedentary lifestyle, which is an important risk factor for non-alcoholic fatty liver disease (NAFLD). But their direct relationship remains unclear. We aimed to examine the relationship between CMD-UT and newly diagnosed non-alcoholic fatty liver disease (NAFLD) in Chinese adults. This cross-sectional study was conducted on 7516 adults in Tianjin, China. The CMD-UT was collected via a questionnaire included five categories. NAFLD [with normal or elevated alanine transaminase (ALT) levels] was diagnosed by at least twice liver ultrasonography examinations and serum ALT concentrations (>41 U/L in males and >33 U/L in females). The prevalence of overall NAFLD, NAFLD with normal or elevated ALT levels was 18.2, 14.2, and 4.0%, respectively. After adjustments for potential confounding factors, the odds ratios (95% confidence interval) of having overall NAFLD by increasing CMD-UT levels were 1.00 for <1 h/d, 1.58 (1.22-2.05) for 1-3 h/d, 1.58 (1.18-2.11) for 3-5 h/d, 1.65 (1.21-2.27) for 5-10 h/d, and 1.99 (1.29-3.05) for ≥10h/d (P-trend for CMD-UT levels = 0.02), respectively. Similar relations were observed with the use of NAFLD with normal or elevated ALT levels. The present study is the first to find that CMD-UT levels are independently associated with NAFLD. Key Messages The computer/mobile devices usage time levels are independently associated with the prevalence of non-alcoholic fatty liver disease.

Musculoskeletal health profile for elite female footballers versus untrained young women before and after 16 weeks of football training.

PubMed

Jackman, Sarah R; Scott, Suzanne; Randers, Morten Bredsgaard; Orntoft, Christina; Blackwell, Jamie; Zar, Abdossaleh; Helge, Eva Wulff; Mohr, Magni; Krustrup, Peter

2013-01-01

We investigated the musculoskeletal health profile of elite female football players (ET) in comparison to untrained (UT) young women subjected to 16 weeks of football training (2 × 1 h per week). DXA scans, blood sampling, sprint testing and Flamingo postural balance testing were carried out for 27 Danish national team players and 28 untrained women, with eight women being tested after training. At baseline total BMD and BMC were 13% (1.305 ± 0.050 versus 1.159 ± 0.056 g · cm(-2)) and 23% (3047 ± 235 versus 2477 ± 526 g) higher (P <0.001) and leg BMD and BMC were 24 and 28% higher (P <0.01) in ET than in UT. Resting plasma osteocalcin was 45% higher in ET than in UT (28.8 ± 10.9 versus 19.9 ± 9.9 µg · L(-1), P <0.05). Total lean body mass was 14% higher (50.4 ± 3.3 versus 44.3 ± 4.0 kg) in ET compared with UT, with no difference in total body mass. The number of Flamingo test falls was 56-63% less (P <0.01) and 30 m sprinting speed was 31% faster (P <0.001) in ET than UT. After 16 weeks of football training for UT, lean body mass increased by 1.4 ± 0.5 kg and the number of left leg falls decreased by 29% (P <0.05). No significant changes occurred in BMD or BMC, but plasma osteocalcin increased (P <0.05) by 37%. In summary, elite women footballers have an impressive musculoskeletal health profile compared with untrained controls, but short-term football training seems to reduce the risk of falls and increase bone formation.

Concentrically trained cyclists are not more susceptible to eccentric exercise-induced muscle damage than are stretch-shortening exercise-trained runners.

PubMed

Snieckus, Audrius; Kamandulis, Sigitas; Venckūnas, Tomas; Brazaitis, Marius; Volungevičius, Gintautas; Skurvydas, Albertas

2013-03-01

Here, we test the hypothesis that continuous concentric exercise training renders skeletal muscles more susceptible to damage in response to eccentric exercise. Elite road cyclists (CYC; n = 10, training experience 8.1 ± 2.0 years, age 22.9 ± 3.7 years), long-distance runners (LDR; n = 10, 9.9 ± 2.3 years, 24.4 ± 2.5 years), and healthy untrained (UT) men (n = 10; 22.4 ± 1.7 years) performed 100 submaximal eccentric contractions at constant angular velocity of 60° s(-1). Concentric isokinetic peak torque, isometric maximal voluntary contraction (MVC), and electrically induced knee extension torque were measured at baseline and immediately and 48 h after an eccentric exercise bout. Muscle soreness was assessed and plasma creatine kinase (CK) activity was measured at baseline and 48 h after exercise. Voluntary and electrically stimulated knee extension torque reduction were significantly greater (p < 0.05) in UT than in LDR and CYC. Immediately and 48 h after exercise, MVC decreased by 32 % and 20 % in UT, 20 % and 5 % in LDR, and 25 % and 6 % in CYC. Electrically induced 20 Hz torque decreased at the same times by 61 and 29 % in UT, 40 and 17 % in LDR, and 26 and 14 % in CYC. Muscle soreness and plasma CK activity 48 h after exercise did not differ significantly between athletes and UT subjects. In conclusion, even though elite endurance athletes are more resistant to eccentric exercise-induced muscle damage than are UT people, stretch-shortening exercise-trained LDR have no advantage over concentrically trained CYC.

Enhanced Right-Chamber Remodeling in Endurance Ultra-Trail Athletes Compared to Marathon Runners Detected by Standard and Speckle-Tracking Echocardiography

PubMed Central

Ujka, Kristian; Bastiani, Luca; D'Angelo, Gennaro; Catuzzo, Bruna; Tonacci, Alessandro; Mrakic-Sposta, Simona; Vezzoli, Alessandra; Giardini, Guido; Pratali, Lorenza

2017-01-01

Background: Strenuous and endurance exercise training have been associated with morphological and functional heart remodeling. Two-dimensional speckle-tracking echocardiography (STE) is a novel technique that allows an accurate quantification of global myocardium deformation. Our aim was to evaluate together left and right cardiac remodeling in different long-distance running athletes: marathon runners (42 km) (M) and endurance mountain runners (>300 Km) (UT). Methods: A total of 92 athletes (70 males, 76%) including 47 M [age 45 ± 7 years; training: 18 (9–53) years*days/week], 45 UT [age 42 ± 9, training: 30 (15–66) years*days/week] underwent conventional echocardiography and STE (Beyond Diogenes 2.0, AMID) during the agonistic season. Results: Right ventricle (RV) end-diastolic area (p = 0.026), fractional area changing (FAC) (p = 0.008) and RV global longitudinal strain (GLS) were significantly increasedin UT athletes. Furthermore, UT showed larger right atrium (RA) volume (p = 0.03), reduced RA GLS and significantly increased RA global circumferential strain (GCS) compared to M. After adjustment for age, sex, and HR as covariates, UT showed a reduced RA GLS (OR 0.907; CI 0.856–0.961) and increased RV FAC (OR 1.172; CI: 1.044–1.317) compared to M. Conclusion: Athletes enrolled in UT endurance activities showed RV and RA morphological and functional remodeling to increased preload in comparison with M runners characterized by increased RV FAC and reduced RA GLS. Follow-up studies are needed to better assess the long-term clinical impact of these modifications. 2D STE is a useful tool for investigating the deformation dynamic in different sports specialties. PMID:28790928

Role of IMF By in the prompt electric field disturbances over equatorial ionosphere during a space weather event

NASA Astrophysics Data System (ADS)

Chakrabarty, D.; Hui, Debrup; Rout, Diptiranjan; Sekar, R.; Bhattacharyya, Archana; Reeves, G. D.; Ruohoniemi, J. M.

2017-02-01

On 7 January 2005 (Ap=40) prompt penetration electric field perturbations of opposite polarities were observed over Thumba and Jicamarca on a few occasions during 13:45-16:30 UT. However, the electric field was found to be eastward during 14:45-15:30 UT over both Thumba and Jicamarca contrary to the general expectation wherein opposite polarities are expected at nearly antipodal points. On closer scrutiny, three important observational features are noticed during 14:10-15:15 UT. First, during 14:10-14:45 UT, despite increasing southward interplanetary magnetic field (IMF) Bz condition, the already westward electric field over Thumba weakened (less westward) while the eastward electric field over Jicamarca intensified (more eastward). Second, the electric field not only became anomalously eastward over Thumba but also got intensified further during 14:45-15:00 UT similar to Jicamarca. Third, during 15:00-15:15 UT, despite IMF Bz remaining steadily southward, the eastward electric field continued to intensify over Thumba but weakened over Jicamarca. It is suggested that the changes in IMF By component under southward IMF Bz condition are responsible for skewing the ionospheric equipotential patterns over the dip equator in such a way that Thumba came into the same DP2 cell as that of Jicamarca leading to anomalous electric field variations. Magnetic field measurements along the Indian and Jicamarca longitude sectors and changes in high-latitude ionospheric convection patterns provide credence to this proposition. Thus, the present investigation shows that the variations in IMF By are fundamentally important to understand the prompt penetration effects over low latitudes.

CHINESE PLAT, 1919 (L19 19 4 E, SALT LAKE CITY ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

CHINESE PLAT, 1919 (L19 19 4 E, SALT LAKE CITY CEMETERY LOCATER), SALT LAKE CITY, UT. VIEW LOOKING NORTHEAST AT CHINESE PLAT MARKER, BURNER & CHINESE GRAVES. - Salt Lake City Cemetery, 200 N Street, Salt Lake City, Salt Lake County, UT

Modulation of sheep ruminal urea transport by ammonia and pH.

PubMed

Lu, Zhongyan; Stumpff, Friederike; Deiner, Carolin; Rosendahl, Julia; Braun, Hannah; Abdoun, Khalid; Aschenbach, Jörg R; Martens, Holger

2014-09-01

Ruminal fermentation products such as short-chain fatty acids (SCFA) and CO2 acutely stimulate urea transport across the ruminal epithelium in vivo, whereas ammonia has inhibitory effects. Uptake and signaling pathways remain obscure. The ruminal expression of SLC14a1 (UT-B) was studied using polymerase chain reaction (PCR). The functional short-term effects of ammonia on cytosolic pH (pHi) and ruminal urea transport across native epithelia were investigated using pH-sensitive microelectrodes and via flux measurements in Ussing chambers. Two variants (UT-B1 and UT-B2) could be fully sequenced from ovine ruminal cDNA. Functionally, transport was passive and modulated by luminal pH in the presence of SCFA and CO2, rising in response to luminal acidification to a peak value at pH 5.8 and dropping with further acidification, resulting in a bell-shaped curve. Presence of ammonia reduced the amplitude, but not the shape of the relationship between urea flux and pH, so that urea flux remained maximal at pH 5.8. Effects of ammonia were concentration dependent, with saturation at 5 mmol/l. Clamping the transepithelial potential altered the inhibitory potential of ammonia on urea flux. Ammonia depolarized the apical membrane and acidified pHi, suggesting that, at physiological pH (< 7), uptake of NH4 (+) into the cytosol may be a key signaling event regulating ruminal urea transport. We conclude that transport of urea across the ruminal epithelium involves proteins subject to rapid modulation by manipulations that alter pHi and the cytosolic concentration of NH4 (+). Implications for epithelial and ruminal homeostasis are discussed. Copyright © 2014 the American Physiological Society.

Giant Metrewave Radio Telescope Monitoring of the Black Hole X-Ray Binary, V404 Cygni during Its 2015 June Outburst

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chandra, Poonam; Kanekar, Nissim

We report results from a Giant Metrewave Radio Telescope (GMRT) monitoring campaign of the black hole X-ray binary V404 Cygni during its 2015 June outburst. The GMRT observations were carried out at observing frequencies of 1280, 610, 325, and 235 MHz, and extended from June 26.89 UT (a day after the strongest radio/X-ray outburst) to July 12.93 UT. We find the low-frequency radio emission of V404 Cygni to be extremely bright and fast-decaying in the outburst phase, with an inverted spectrum below 1.5 GHz and an intermediate X-ray state. The radio emission settles to a weak, quiescent state ≈11 daysmore » after the outburst, with a flat radio spectrum and a soft X-ray state. Combining the GMRT measurements with flux density estimates from the literature, we identify a spectral turnover in the radio spectrum at ≈1.5 GHz on ≈ June 26.9 UT, indicating the presence of a synchrotron self-absorbed emitting region. We use the measured flux density at the turnover frequency with the assumption of equipartition of energy between the particles and the magnetic field to infer the jet radius (≈4.0 × 10{sup 13} cm), magnetic field (≈0.5 G), minimum total energy (≈7 × 10{sup 39} erg), and transient jet power (≈8 × 10{sup 34} erg s{sup −1}). The relatively low value of the jet power, despite V404 Cygni’s high black hole spin parameter, suggests that the radio jet power does not correlate with the spin parameter.« less

Observations of Deep Ionospheric F-Region Density Depletions with FPMU Instrumentation and their Relationship with the Global Dynamics of the June 22-23, 2015 Geomagnetic Storm

NASA Technical Reports Server (NTRS)

Coffey, Victoria; Sazykin, Stan; Chandler, Michael; Hairston, Marc; Minow, Joseph; Anderson, Brian

2017-01-01

The magnetic storm that commenced on June 22, 2015 was one of the largest storms in the current solar cycle, resulting from an active region on the Sun that produced numerous coronal mass ejections (CMEs) and associated interplanetary shock waves. On June 22 at 18:36 UT the magnetosphere was impacted by the leading-edge shock wave and a sheath carrying a large and highly variable interplanetary magnetic field (IMF) Bz with values ranging from +25 to -40 nT. During the subsequent interval from 0000 to 0800 UT, there was a second intensification of the geomagnetic storm resulting from the impact of the CME. We present dramatic responses of simultaneous particle measurements from the high-altitude Magnetospheric Multiscale Mission (MMS) at high altitudes in the magnetosphere (approx. 9-12 Re) and from the low-altitude (F-region) Floating Potential Measurement Unit (FPMU) on board the International Space Station (ISS). We analyze potential causes of these dramatic particle flux dropouts by putting them in the context of storm-time electrodynamics, and support our results with numerical simulations of the global magnetosphere and ionosphere. During the sheath phase of the storm, the MMS spacecraft in the near-earth equatorial plane observed a rapid reconfiguration of the magnetic field near 1923 UT. Initially in the warm plasmasheet, particle flux dropouts were observed as they tracked the plasma-sheet to lobe transitions with the stretching and thinning of the plasmasheet. Anti-sunward flowing O+ ions of ionospheric origin were also measured during this period, confirming that the MMS spacecraft temporarily was in a lobe.

Observations of Deep Ionospheric F-Region Density Depletions with FPMU Instrumentation and Their Relationship with the Global Dynamics of the June 22-23, 2015 Geomagnetic Storm

NASA Technical Reports Server (NTRS)

Coffey, Victoria; Sazykin, Stan; Chandler, Michael; Hairston, Marc; Minow, Joseph; Anderson, Brian

2017-01-01

The magnetic storm that commenced on June 22, 2015 was one of the largest storms in the current solar cycle, resulting from an active region on the Sun that produced numerous coronal mass ejections (CMEs) and associated interplanetary shock waves. On June 22 at 18:36 UT the magnetosphere was impacted by the leading-edge shock wave and a sheath carrying a large and highly variable interplanetary magnetic field (IMF) Bz with values ranging from +25 to -40 nT. During the subsequent interval from 0000 to 0800 UT, there was a second intensification of the geomagnetic storm resulting from the impact of the CME. We present dramatic responses of simultaneous particle measurements from the high-altitude Magnetospheric Multiscale Mission (MMS) at high altitudes in the magnetosphere (approx. 9-12 Re) and from the low-altitude (F-region) Floating Potential Measurement Unit (FPMU) on board the International Space Station (ISS). We analyze potential causes of these dramatic particle flux dropouts by putting them in the context of storm-time electrodynamics, and support our results with numerical simulations of the global magnetosphere and ionosphere. During the sheath phase of the storm, the MMS spacecraft in the near-earth equatorial plane observed a rapid reconfiguration of the magnetic field near 1923 UT. Initially in the warm plasma sheet, particle flux dropouts were observed as they tracked the plasma-sheet to lobe transitions with the stretching and thinning of the plasma sheet. Anti-sunward flowing O+ ions of ionospheric origin were also measured during this period, confirming that the MMS spacecraft temporarily was in a lobe.

Ultrathin nanosheets of graphitic carbon nitride heterojunction with flower like Bi2O3 for photodegradation of organic pollutants

NASA Astrophysics Data System (ADS)

Bano, Zahira; Muhmood, Tahir; Xia, Mingzhu; Lei, Wu; Wang, Fengyun

2018-05-01

The flower like microrods (MR) of α-Bi2O3 defined as (MR-Bi2O3) and ultrathin g-C3N4(UT-C3N4) p-n junction was successfully prepared by loading different concentrations of UT-C3N4 over MR-Bi2O3. Their morphology and structure were thoroughly studied by XRD, SEM, XPS, TEM, UV–vis diffuse reflectance spectra, FT-IR and PL spectra. The results showed that the UT-C3N4 has been wrapped in the flower like MR-Bi2O3. The designing of the p-n junction of UT- C3N4 and MR-Bi2O3 can enhance the separation efficiency of the electron-hole pairs. The photocatalytic degradation of RhB was drastically increased by designing of the p-n junction that is due to the photogenerated electron–hole pair’s separation efficiency.

Regulation of renal urea transport by vasopressin.

PubMed

Sands, Jeff M; Blount, Mitsi A; Klein, Janet D

2011-01-01

Terrestrial life would be miserable without the ability to concentrate urine. Production of concentrated urine requires complex interactions among the nephron segments and vasculature in the kidney medulla. In addition to water channels (aquaporins) and sodium transporters, urea transporters are critically important to the theories proposed to explain the physiologic processes occurring when urine is concentrated. Vasopressin (anti-diuretic hormone) is the key hormone regulating the production of concentrated urine. Vasopressin rapidly increases water and urea transport in the terminal inner medullary collecting duct (IMCD). Vasopressin rapidly increases urea permeability in the IMCD through increases in phosphorylation and apical plasma-membrane accumulation of the urea transporter A1 (UT-A1). Vasopressin acts through two cAMP-dependent signaling pathways in the IMCD: protein kinase A and exchange protein activated by cAMP Epac. Protein kinase A phosphorylates UT-A1 at serines 486 and 499. In summary, vasopressin regulates urea transport acutely by increasing UT-A1 phosphorylation and the apical plasma-membrane accumulation of UT-A1 through two cAMP-dependent pathways.

Nova Scorpii 2011 = PNV J16551100-3838120

NASA Astrophysics Data System (ADS)

Waagen, Elizabeth O.

2011-06-01

Announces the discovery of Nova Scorpii 2011 = PNV J16551100-3838120 by John Seach (Chatsworth Island, NSW, Australia) on 2011 June 1.40 UT at magnitude 9.5 (DSLR + orange filter). Spectra by Bernard Heathcote (South Yarra, Vic, Australia) on Jun 2.4896 UT, A. Arai, T. Kajikawa, and M. Nagashima (Kyoto Sangyo University, Japan) on 2011 June 2.68 UT, and Masayuki Yamanaka and Ryosuke Itoh (Hiroshima University, Japan) on Jun 2 UT indicate a highly-reddened classical nova. Initially reported to the AAVSO by Seach and announced in AAVSO Special Notice #240 (Arne Henden) and IAU CBET 2735 (Daniel W. E. Green, ed.). The object was designated PNV J18102135-2305306 when posted on the Central Bureau's Transient Objects Confirmation Page (TOCP) webpage. Finder charts with sequence may be created using the AAVSO Variable Star Plotter (http://www.aavso.org/vsp). Observations should be submitted to the AAVSO International Database. See full Alert Notice for more details, observations, and links to images. [Nova Sco 2011 subsequently assigned the name V1312 Sco

Une complication rare des léiomyomes utérins: hémopéritoine massif par rupture de varices

PubMed Central

Ymele, Florent Fouelifack; Tsuala, Jovanny Fouogue; Fouedjio, Jeanne Hortence; Nangué, Charlette; De Kayo, Caroline Kayo; Dobgima, Pisoh Walter; Mbu, Robinson Enoh

2013-01-01

Les léiomyomes utérins sont des causes exceptionnelles d'hémopéritoine. Nous rapportons ici le cas d'une femme de 46 ans nullipare, en instance d'une hystérectomie totale indiquée pour utérus polymyomateux symptomatique. Elle a été opérée en urgence pour hémopéritoine aigu et massif compliqué de choc hémorragique. L'origine de l'hémopéritoine était la rupture spontanée d'une varice du léiomyome. Quoique rare l'éventualité d'un hémopéritoine causé par un fibrome utérin devrait être évoquée devant tout abdomen aigu spontané chez une femme en âge de procréer. La présence de varices sur les fibromes augmenterait le risque d'hémorragie spontanée. PMID:23717724

VizieR Online Data Catalog: The AllWISE motion survey (AllWISE2) (Kirkpatrick+, 2016)

NASA Astrophysics Data System (ADS)

Kirkpatrick, J. D.; Kellogg, K.; Schneider, A. C.; Fajardo-Acosta, S.; Cushing, M. C.; Greco, J.; Mace, G. N.; Gelino, C. R.; Wright, E. L.; Eisenhardt, P. R. M.; Stern, D.; Faherty, J. K.; Sheppard, S. S.; Lansbury, G. B.; Logsdon, S. E.; Martin, E. C.; McLean, I. S.; Schurr, S. D.; Cutri, R. M.; Conrow, T.

2016-07-01

Observations for the spectroscopic follow-up of interesting AllWISE sources are listed in Table 4. Optical follow-up was conducted with the Palomar/Double Spectrograph on the Hale 5m telescope on Palomar Mountain, California, as our primary optical spectrograph in the northern hemisphere. It was used during the UT nights of 2014 January 26, February 23/24, April 22, June 25/26, July 21, September 27, October 24, and November 15 as well as 2015 June 08, September 07, and December 10. The Boller & Chivens Spectrograph (BCSpec) on the 2.5m Irenee duPont telescope at Las Campanas Observatory, Chile, served as our primary optical spectrograph in the southern hemisphere and was used on the UT nights of 2014 April 30, May 01-04, and November 16-20. Spectra of 10 objects were obtained on the UT nights of 2014 July 03-04 and 2015 December 07-10 at the European Southern Observatory (ESO) 3.58m New Technology Telescope (NTT) at La Silla, Chile. Spectra of seven objects were obtained on the UT nights of 2014 June 26, 2015 August 13, and 2015 December 05 with the Low Resolution Imaging Spectrometer (LRIS) at the 10m W. M. Keck Observatory on Mauna Kea, Hawaii. SpeX on the NASA 3m Infrared Telescope Facility (IRTF) on Mauna Kea, Hawaii, served as our primary near-infrared spectrograph in the northern hemisphere. The UT dates of observation were 2014 November 11 and 2015 January 27, May 08-09, June 27, July 03-05, and July 20. The Folded-port Infrared Echellette (FIRE) at the 6.5m Walter Baade Telescope at Las Campanas Observatory, Chile, served as our primary near-infrared spectrograph in the southern hemisphere. The UT dates of observation were 2014 August 07-09, 2015 February 08, and 2015 May 31. Several sources were also observed with the Near-Infrared Spectrometer (NIRSPEC) at the 10m W. M. Keck Observatory on Mauna Kea, Hawaii. The observation dates were UT 2014 April 12 and December 03, and 2015 July 03 and July 11. (9 data files).

Nitrogen oxides in the global upper troposphere interpreted with cloud-sliced NO2 from the Ozone Monitoring Instrument

NASA Astrophysics Data System (ADS)

Marais, Eloise A.; Jacob, Daniel J.; Choi, Sungyeon; Joiner, Joanna; Belmonte-Rivas, Maria; Cohen, Ronald C.; Ryerson, Thomas B.; Weinheimer, Andrew J.; Volz-Thomas, Andreas

2017-04-01

Nitrogen oxides (NOx ≡ NO + NO2) are long lived in the upper troposphere (UT), and so have a large impact on ozone formation where ozone is a powerful greenhouse gas. Measurements of UT NOx are limited to summertime aircraft campaigns predominantly in North America. There are year-round NOx measurements from instruments onboard commercial aircraft, but NO2 measurements are susceptible to large interferences. Satellites provide global coverage, but traditional space-based NO2 observations only provide one piece of vertical information in the troposphere. New cloud-sliced satellite NO2 products offer additional vertical information by retrieving partial NO2 columns above clouds and further exploit differences in cloud heights to calculate UT NO2 mixing ratios. Two new cloud-sliced NO2 products from the Ozone Monitoring Instrument (OMI; 2004 launch) provide seasonal UT NO2 data centered at 350 hPa for 2005-2007 (NASA product) and 380 hPa for 2006 only (KNMI). Differences between the products include spectral fitting to obtain NO2 along the viewing path (slant column), the air mass factor calculation to convert slant columns to true vertical columns, treatment of the stratospheric NO2 component, and the choice of cloud products. The resultant NASA NO2 mixing ratios are 30% higher than KNMI NO2 and are consistent with summertime aircraft NO2 observations over North America. Comparison between NASA NO2 and the GEOS-Chem chemical transport model exposes glaring inadequacies in the model. In summer in the eastern US lightning NOx emissions are overestimated by at least a factor of 2, corroborated by comparison of GEOS-Chem and MOZAIC aircraft observations of reactive nitrogen (NOy). Too fast heterogeneous hydrolysis of dinitrogen pentoxide (N2O5) leads to an underestimate in UT NO2 in winter across the northern hemisphere. Absence of interannual variability in lightning flashes in the lightning NOx parameterization induces biases in UT NO2 in the tropics due to anomalous lightning activity linked to the El Niño Southern Oscillation. Ongoing work is to use GEOS-Chem to investigate the implications of updated representation of UT NOx on ozone.

Mechanical Characteristics, In Vitro Degradation, Cytotoxicity, and Antibacterial Evaluation of Zn-4.0Ag Alloy as a Biodegradable Material

PubMed Central

Li, Ping; Schille, Christine; Schweizer, Ernst; Rupp, Frank; Heiss, Alexander; Legner, Claudia; Klotz, Ulrich E.; Geis-Gerstorfer, Jürgen

2018-01-01

Zn-based biodegradable metallic materials have been regarded as new potential biomaterials for use as biodegradable implants, mainly because of the ideal degradation rate compared with those of Mg-based alloys and Fe-based alloys. In this study, we developed and investigated a novel Zn-4 wt % Ag alloy as a potential biodegradable metal. A thermomechanical treatment was applied to refine the microstructure and, consequently, to improve the mechanical properties, compared to pure Zn. The yield strength (YS), ultimate tensile strength (UTS) and elongation of the Zn-4Ag alloy are 157 MPa, 261 MPa, and 37%, respectively. The corrosion rate of Zn-4Ag calculated from released Zn ions in DMEM extracts is approximately 0.75 ± 0.16 μg cm–2 day–1, which is higher than that of pure Zn. In vitro cytotoxicity tests showed that the Zn-4Ag alloy exhibits acceptable toxicity to L929 and Saos-2 cells, and could effectively inhibit initial bacteria adhesion. This study shows that the Zn-4Ag exhibits excellent mechanical properties, predictable degradation behavior, acceptable biocompatibility, and effective antibacterial properties, which make it a candidate biodegradable material. PMID:29518938

The Role of Retained Austenite on the Mechanical Properties of a Low Carbon 3Mn-1.5Ni Steel

NASA Astrophysics Data System (ADS)

Chen, Jun; Zhang, Wei-na; Liu, Zhen-yu; Wang, Guo-dong

2017-12-01

The present studies focus on the correlation between retained austenite characteristics and the cryogenic temperature Charpy impact toughness, strength, and plasticity. The steels with different volume fractions and stabilities of retained austenite were prepared by quenching followed by intercritical heat treatment, and the microstructure was characterized using scanning electron microscope, electron back-scattered diffraction, and X-ray diffraction. The grain size, dislocation density, crack initiation energy, and crack propagation energy were quantified. It has been demonstrated that the volume fraction of retained austenite plays a significant role in the reduction of the measured yield strength and the effect of tempered martensite/ferrite matrix on cryogenic temperature impact toughness can be assumed to be similar due to the similar grain size, dislocation density and element content in solution for different heat treatments. It was found that the stability of retained austenite plays a determining role in the increase of cryogenic temperature impact toughness. Furthermore, the dependence of the crack propagation energy on retained austenite is much greater than that of the crack initiation energy. Generally, an excellent UTS × TEL does not produce good cryogenic temperature impact toughness.

Strengthening Effect of Extruded Mg-8Sn-2Zn-2Al Alloy: Influence of Micro and Nano-Size Mg2Sn Precipitates

PubMed Central

Cheng, Weili; Bai, Yang; Wang, Lifei; Wang, Hongxia; Bian, Liping; Yu, Hui

2017-01-01

In this study, Mg-8Sn-2Zn-2Al (TZA822) alloys with varying Mg2Sn contents prior to extrusion were obtained by different pre-treatments (without and with T4), and the strengthening response related to micro and nano-size Mg2Sn precipitates in the extruded TZA822 alloys was reported. The results showed that the morphology of nano-size Mg2Sn precipitates exhibits a significant change in basal plane from rod-like to spherical, owing to the decrement in the fraction of micro-size particles before extrusion. Meanwhile, the spherical Mg2Sn precipitates provided a much stronger strengthening effect than did the rod-like ones, which was ascribed to uniform dispersion and refinement of spherical precipitates to effectively hinder basal dislocation slip. As a consequence, the extruded TZA822 alloy with T4 showed a higher tensile yield strength (TYS) of 245 MPa, ultimate tensile strength (UTS) of 320 MPa and elongation (EL) of 26.5%, as well as a lower degree of yield asymmetry than their counterpart without T4. Detailed reasons for the strengthening effect were given and analyzed. PMID:28773180

Structure formation in grade 20 steel during equal-channel angular pressing and subsequent heating

NASA Astrophysics Data System (ADS)

Dobatkin, S. V.; Odesskii, P. D.; Raab, G. I.; Tyutin, M. R.; Rybalchenko, O. V.

2016-11-01

The structure formation and the mechanical properties of quenched and tempered grade 20 steel after equal-channel angular pressing (ECAP) at various true strains and 400°C are studied. Electron microscopy analysis after ECAP shows a partially submicrocrystalline and partially subgrain structure with a structural element size of 340-375 nm. The structural element size depends on the region in which the elements are formed (polyhedral ferrite, needle-shaped ferrite, tempered martensite, and pearlite). Heating of the steel after ECAP at 400 and 450°C increases the fraction of high-angle boundaries and the structural ferrite element size to 360-450 nm. The fragmentation and spheroidization of cementite lamellae of pearlite and subgrain coalescence in the regions of needle-shaped ferrite and tempered martensite take place at a high ECAP true strain and heating temperature. Structural refinement ensures considerable strengthening, namely, UTS 742-871 MPa at EL 11-15.3%. The strength slightly increases, whereas the plasticity slightly decreases when the true strain increases during ECAP. After ECAP and heating, the strength and plastic properties of the grade 20 steel remain almost the same.

Strengthening Effect of Extruded Mg-8Sn-2Zn-2Al Alloy: Influence of Micro and Nano-Size Mg₂Sn Precipitates.

PubMed

Cheng, Weili; Bai, Yang; Wang, Lifei; Wang, Hongxia; Bian, Liping; Yu, Hui

2017-07-18

In this study, Mg-8Sn-2Zn-2Al (TZA822) alloys with varying Mg₂Sn contents prior to extrusion were obtained by different pre-treatments (without and with T4), and the strengthening response related to micro and nano-size Mg₂Sn precipitates in the extruded TZA822 alloys was reported. The results showed that the morphology of nano-size Mg₂Sn precipitates exhibits a significant change in basal plane from rod-like to spherical, owing to the decrement in the fraction of micro-size particles before extrusion. Meanwhile, the spherical Mg₂Sn precipitates provided a much stronger strengthening effect than did the rod-like ones, which was ascribed to uniform dispersion and refinement of spherical precipitates to effectively hinder basal dislocation slip. As a consequence, the extruded TZA822 alloy with T4 showed a higher tensile yield strength (TYS) of 245 MPa, ultimate tensile strength (UTS) of 320 MPa and elongation (EL) of 26.5%, as well as a lower degree of yield asymmetry than their counterpart without T4. Detailed reasons for the strengthening effect were given and analyzed.

On the Performance of Quorum Replication on the Internet

DTIC Science & Technology

2008-10-31

ISP in Cambridge, MA MA2 ISP in Cambridge, MA MA3 ISP in Martha’s Vineyard, MA MA4 ISP in Massachusetts, MA MD ISP in Laurel, MD MEX National...1523 171 96% 58% MA2 28% 742 1517 230 94% 59% NC 32% 465 616 255 90% 63% ISR2 3% 424 70 400 100% 97% UT1 27% 979 1847 189 96% 55% MA1 29% 645 712 238... MA2 UT2 UT1 CA1 AUS NC NZ TW KR CA2 CA3 Fig. 4. Our crumbling wall quorum system. of the first row are in North America. TW, which has lossy

Spectroscopic classification of supernova SN 2018Z by NUTS (NOT Un-biased Transient Survey)

NASA Astrophysics Data System (ADS)

Kuncarayakti, H.; Mattila, S.; Kotak, R.; Harmanen, J.; Reynolds, T.; Pastorello, A.; Benetti, S.; Stritzinger, M.; Onori, F.; Somero, A.; Kangas, T.; Lundqvist, P.; Taddia, F.; Ergon, M.

2018-01-01

The NOT Unbiased Transient Survey (NUTS; ATel #8992) collaboration reports the spectroscopic classification of supernova SN 2018Z in host galaxy SDSS J231809.76+212553.5 The observations were performed with the 2.56 m Nordic Optical Telescope equipped with ALFOSC (range 350-950 nm; resolution 1.6 nm) on 2018-01-09.9 UT. Survey Name | IAU Name | Discovery (UT) | Discovery mag | Observation (UT) | Redshift | Type | Phase | Notes PS18ao | SN 2018Z | 2018-01-01.2 | 19.96 | 2018-01-09.9 | 0.102 | Ia | post-maximum? | (1) (1) Redshift was derived from the SN and host absorption features.

Comet ISON Swoops Around the Sun

NASA Image and Video Library

2013-12-02

Comet ISON swoops around the sun and through Scorpius. This composite merges an SDO AIA 171 sun image (Nov. 28, 2214 UT), SOHO C2 (2036 UT) and C3 (2030 UT) images, and a DSS view of the sky in northern Scorpius. Credit: NASA/ESA/SOHO, NASA/SDO, DSS, and Francis Reddy NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

Spectroscopic classification of SN 2017hro with NOT

NASA Astrophysics Data System (ADS)

Babooram, C.; Jormanainen, J.; Wagner, S.; Wierda, F.; Kuncarayakti, H.; Fedorets, G.; Dyrbye, S.

2017-11-01

We report the spectroscopic classification of supernova SN 2017hro (ATLAS17mwv) in host galaxy 2MASX J22161573+4003267. The observations were performed with the 2.56 m Nordic Optical Telescope equipped with ALFOSC (range 350-950 nm; resolution 1.6 nm) on 2017-11-01.8 UT. Survey Name | IAU Name | Discovery (UT) | Discovery mag | Observation (UT) | Redshift | Type | Phase | Notes ATLAS17mwv | SN 2017hro | 2017-10-28.3 | 18.765 | 2017-11-01.8 | 0.015 | II | around maximum | (1) (1) SN redshift is obtained from host emission lines and consistent with that derived from the SN spectrum.

77 FR 61652 - Utah Disaster # UT-00015

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-10

... SMALL BUSINESS ADMINISTRATION [Disaster Declaration 13326 and 13327] Utah Disaster UT-00015 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY: This is a notice of an Administrative declaration of a disaster for the State of UTAH dated 10/01/2012. Incident: Flooding. Incident Period: 09/11...

Swift/XRT detection of an outburst from SXP 15.3

NASA Astrophysics Data System (ADS)

Ducci, L.; Romano, P.; Kennea, J. A.; Malacaria, C.; Covino, S.; Santangelo, A.; Evans, P. A.; Coe, M. J.; Townsend, L. J.

2017-12-01

During an observation of the Small Magellanic Cloud (SMC) carried out from December 2nd 2017, 11:12:03 UT to 19:30:52 UT (total exposure time of 7 ks), Swift/XRT detected renewed activity from the Be X-ray binary SXP 15.3.

76 FR 45177 - Establishment of Class E Airspace; Nephi, UT

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-28

... at Nephi UT, to accommodate aircraft using new Area Navigation (RNAV) Global Positioning System (GPS) standard instrument approach procedures at Nephi Municipal Airport. This improves the safety and management of Instrument Flight Rules (IFR) operations at the airport. DATES: Effective date, 0901 UTC, October...

Distinct sources of particles near the cusp and the dusk flank of the magnetosphere

NASA Astrophysics Data System (ADS)

Escoubet, C. P.; Grison, B.; Berchem, J.; Trattner, K. J.; Lavraud, B.; Pitout, F.; Soucek, J.; Richard, R. L.; Laakso, H. E.; Masson, A.; Dunlop, M.; Dandouras, I. S.; Rème, H.; Fazakerley, A. N.; Daly, P. W.

2015-12-01

At the magnetopause, the location of the magnetic reconnection sites depends on the orientation of the interplanetary magnetic field (IMF) in the solar wind: on the dayside magnetosphere for an IMF southward, on the lobes for an IMF northward and on the flanks for an IMF in the East-West direction. Since most of observations of reconnection events have sampled a limited region of space simultaneously it is still not yet know if the reconnection line is extended over large regions of the magnetosphere or if is patchy and made of many reconnection lines. We report a Cluster crossing on 5 January 2002 near the exterior cusp on the southern dusk side where we observe multiple sources of reconnection/injections. The IMF was mainly azimuthal (IMF-By around -5 nT), the solar wind speed lower than usual around 280 km/s with the density of order 5 cm-3. The four Cluster spacecraft had an elongated configuration near the magnetopause. C4 was the first spacecraft to enter the cusp around 19:52:04 UT, followed by C2 at 19:52:35 UT, C1 at 19:54:24 UT and C3 at 20:13:15 UT. C4 and C1 observed two ion energy dispersions at 20:10 UT and 20:40 UT and C3 at 20:35 UT and 21:15 UT. Using the time of flight technique on the upgoing and downgoing ions, which leads to energy dispersions, we obtain distances of the ion sources between 14 and 20 RE from the spacecraft. The slope of the ion energy dispersions confirmed these distances. Using Tsyganenko model, we find that these sources are located on the dusk flank, past the terminator. The first injection by C3 is seen at approximately the same time as the 2nd injection on C1 but their sources at the magnetopause were separated by more than 7 RE. This would imply that two distinct sources were active at the same time on the dusk flank of the magnetosphere. In addition, a flow reversal was observed at the magnetopause on C4 which would be an indication that reconnection is also taking place near the exterior cusp quasi-simultaneously. A three-dimensional global magnetohydrodynamic (MHD) simulation will be used to determine the global topology of the magnetic field during the event.

Analysis of Island Formation Due to RMPs in D3D Plasmas Using SIESTA

NASA Astrophysics Data System (ADS)

Hirshman, Steven; Shafer, Morgan; Seal, Sudip; Canik, John

2015-11-01

By varying the initial helical perturbation amplitude of Resonant Magnetic Perturbations (RMPs) applied to a Doublet III-D (DIII-D) plasma, a variety of meta-stable equilibrium are scanned using the SIESTA MHD equilibrium code. It is found that increasing the perturbation strength at the dominant m =2 resonant surface leads to lower MHD energies and significant increases in the equilibrium island widths at the m =2 (and sidebands) surfaces. Island overlap eventually leads to stochastic magnetic fields which correlate well with the experimentally inferred field line structure. The magnitude and spatial phase (around associated rational surfaces) of resonant (shielding) components of the parallel current is shown to be correlated with the magnetic island topology. Work supported by U.S. DOE under Contract DE-AC05-00OR22725 with UT-Battelle, LLC.

Research on hardness and tensile properties of A390 alloy with tin addition

NASA Astrophysics Data System (ADS)

Si, Yi

2018-03-01

The effect of tin content on hardness and tensile properties of A390 alloys has been discussed. The microstructure of the A390 alloy with tin addition has been surveyed by OM and investigated by SEM. Research showed that β-Sn in the alloy precipitation forms were mainly small blocks and thin strips, particles within the Al2Cu network or large blocks consisting of β-Sn and Al2Cu on Al/Si interfaces or α-Al grain boundaries. Spheroidization of the primary and eutectic silicon was improved due to Sn accretion. With the augment of element tin, hardness of casting alloy is much higher than that of alloy after heat treatment. The elongation and ultimate tensile strength (UTS) were increased in Sn addition from 0 to 1%, which is attributed to the multiple action of Sn.

The effects of smartphone use on upper extremity muscle activity and pain threshold

PubMed Central

Lee, Minkyung; Hong, Yunkyung; Lee, Seunghoon; Won, Jinyoung; Yang, Jinjun; Park, Sookyoung; Chang, Kyu-Tae; Hong, Yonggeun

2015-01-01

[Purpose] The purpose of this study was to determine whether muscle activity and pressure-induced pain in the upper extremities are affected by smartphone use, and to compare the effects of phone handling with one hand and with both hands. [Subjects] The study subjects were asymptomatic women 20–22 years of age. [Methods] The subjects sat in a chair with their feet on the floor and the elbow flexed, holding a smartphone positioned on the thigh. Subsequently, the subjects typed the Korean anthem for 3 min, one-handed or with both hands. Each subject repeated the task three times, with a 5-min rest period between tasks to minimize fatigue. Electromyography (EMG) was used to record the muscle activity of the upper trapezius (UT), extensor pollicis longus (EPL), and abductor pollicis (AP) during phone operation. We also used a dolorimeter to measure the pressure-induced pain threshold in the UT. [Results] We observed higher muscle activity in the UT, AP, and EPL in one-handed smartphone use than in its two-handed use. The pressure-induced pain threshold of the UT was lower after use of the smartphone, especially after one-handed use. [Conclusion] Our results show that smartphone operation with one hand caused greater UT pain and induced increased upper extremity muscle activity. PMID:26180311

High-flavanol and high-theobromine versus low-flavanol and low-theobromine chocolate to improve uterine artery pulsatility index: a double blind randomized clinical trial.

PubMed

Bujold, Emmanuel; Leblanc, Vicky; Lavoie-Lebel, Élise; Babar, Asma; Girard, Mario; Poungui, Lionel; Blanchet, Claudine; Marc, Isabelle; Lemieux, Simone; Belkacem, Abdous; Sidi, Elhadji Laouan; Dodin, Sylvie

2017-09-01

To evaluate the impact of high-flavanol and high-theobromine (HFHT) chocolate in women at risk of preeclampsia (PE). We conducted a single-center randomized controlled trial including women with singleton pregnancy between 11 and 14 weeks gestation who had bilateral abnormal uterine artery (UtA) waveforms (notching) and elevated pulsatility index (PI). Participants were randomized to either HFHT or low-flavanol and low-theobromine (LFLT) chocolate (30 grams daily for a total of 12 weeks). UtA PI, reported as multiple of medians (MoM) adjusted for gestational age, was assessed at baseline and 12 weeks after randomization. One hundred thirty-one women were randomized with mean gestational age of 12.4 ± 0.6 weeks and a mean UtA PI of 1.39 ± 0.31 MoM. UtA PI adjusted for gestational age significantly decreased from baseline to the second visit (12 weeks later) in the two groups (p < 0.0001) but no significant difference was observed between the groups (p = 0.16). Compared with LFLT chocolate, daily intake of HFHT chocolate was not associated with significant changes of UtA PI. Nevertheless, the improvement observed in both groups suggests that chocolate could improve placental function independently of flavanol and/or theobromine content.

CO-CD base management model of Universitas Terbuka community service program

NASA Astrophysics Data System (ADS)

Kridasakti, S. W.; Sudirah; Siregar, H.

2018-03-01

These studies were to respond whether the UT social-aid management had been executed under CO-CD principles (Ife J. 1995) and what CO-CD base community service management model can be built. The goals of these evaluational studies were UT social-aid managerial performance profile (2011-2013) and CO-CD management model development. The methods used were Survey and FGD. For data collection were involving the UT officers, the counterparts, and the documents. The analysis used combination between the Performance Analysis (Irawan P., 2003) and the CIPP (Stuffelbeam, D, L., & Shinkfield, A, J., 1985). The findings showed that the quantitative targeting in program completion was credible in achievement (85%). However, the “qulitative targeting” of the management goals was indicating far from a good-stage (≤5.0_Interval-Force: 1-10 Scale). The “Gap” was due to the absent of socialization_needs-analysis_maintenance_release factors on the UT social-service grand-policy. The trial of CO-CD Base Management Model had been imposed to the community that turned out to be very effective to self-help, and the ensuing SOP had been successfully defined. Conclusion, ‘CO-CD Principles’ were not designed in UT community service programs management. However, if efficiency and effectivity likely to be achieved, the SOP of ‘CO-CD Base Management Model has to be adopted.

Temporary hearing loss influences post-stimulus time histogram and single neuron action potential estimates from human compound action potentials

PubMed Central

Lichtenhan, Jeffery T.; Chertoff, Mark E.

2008-01-01

An analytic compound action potential (CAP) obtained by convolving functional representations of the post-stimulus time histogram summed across auditory nerve neurons [P(t)] and a single neuron action potential [U(t)] was fit to human CAPs. The analytic CAP fit to pre- and postnoise-induced temporary hearing threshold shift (TTS) estimated in vivoP(t) and U(t) and the number of neurons contributing to the CAPs (N). The width of P(t) decreased with increasing signal level and was wider at the lowest signal level following noise exposure. P(t) latency decreased with increasing signal level and was shorter at all signal levels following noise exposure. The damping and oscillatory frequency of U(t) increased with signal level. For subjects with large amounts of TTS, U(t) had greater damping than before noise exposure particularly at low signal levels. Additionally, U(t) oscillation was lower in frequency at all click intensities following noise exposure. N increased with signal level and was smaller after noise exposure at the lowest signal level. Collectively these findings indicate that neurons contributing to the CAP during TTS are fewer in number, shorter in latency, and poorer in synchrony than before noise exposure. Moreover, estimates of single neuron action potentials may decay more rapidly and have a lower oscillatory frequency during TTS. PMID:18397026

Expression of urea transporters and their regulation.

PubMed

Klein, Janet D

2014-01-01

UT-A and UT-B families of urea transporters consist of multiple isoforms that are subject to regulation of both acutely and by long-term measures. This chapter provides a brief overview of the expression of the urea transporter forms and their locations in the kidney. Rapid regulation of UT-A1 results from the combination of phosphorylation and membrane accumulation. Phosphorylation of UT-A1 has been linked to vasopressin and hyperosmolality, although through different kinases. Other acute influences on urea transporter activity are ubiquitination and glycosylation, both of which influence the membrane association of the urea transporter, again through different mechanisms. Long-term regulation of urea transport is most closely associated with the environment that the kidney experiences. Low-protein diets may influence the amount of urea transporter available. Conditions of osmotic diuresis, where urea concentrations are low, will prompt an increase in urea transporter abundance. Although adrenal steroids affect urea transporter abundance, conflicting reports make conclusions tenuous. Urea transporters are upregulated when P2Y2 purinergic receptors are decreased, suggesting a role for these receptors in UT regulation. Hypercalcemia and hypokalemia both cause urine concentration deficiencies. Urea transporter abundances are reduced in aging animals and animals with angiotensin-converting enzyme deficiencies. This chapter will provide information about both rapid and long-term regulation of urea transporters and provide an introduction into the literature.

The Ionospheric Impact of an ICME-Driven Sheath Region Over Indian and American Sectors in the Absence of a Typical Geomagnetic Storm

NASA Astrophysics Data System (ADS)

Rout, Diptiranjan; Chakrabarty, D.; Sarkhel, S.; Sekar, R.; Fejer, B. G.; Reeves, G. D.; Kulkarni, Atul S.; Aponte, Nestor; Sulzer, Mike; Mathews, John D.; Kerr, Robert B.; Noto, John

2018-05-01

On 13 April 2013, the ACE spacecraft detected arrival of an interplanetary shock at 2250 UT, which is followed by the passage of the sheath region of an interplanetary coronal mass ejection (ICME) for a prolonged (18-hr) period. The polarity of interplanetary magnetic field Bz was northward inside the magnetic cloud region of the ICME. The ring current (SYM-H) index did not go below -7 nT during this event suggesting the absence of a typical geomagnetic storm. The responses of the global ionospheric electric field associated with the passage of the ICME sheath region have been investigated using incoherent scatter radar measurements of Jicamarca and Arecibo (postmidnight sector) along with the variations of equatorial electrojet strength over India (day sector). It is found that westward and eastward prompt penetration (PP) electric fields affected ionosphere over Jicamarca/Arecibo and Indian sectors, respectively, during 0545-0800 UT. The polarities of the PP electric field perturbations over the day/night sectors are consistent with model predictions. In fact, DP2-type electric field perturbations with ˜40-min periodicity are found to affect the ionosphere over both the sectors for about 2.25 hr during the passage of the ICME sheath region. This result shows that SYM-H index may not capture the full geoeffectivenss of the ICME sheath-driven storms and suggests that the PP electric field perturbations should be evaluated for geoeffectiveness of ICME when the polarity of interplanetary magnetic field Bz is northward inside the magnetic cloud region of the ICME.

An evidence for prompt electric field disturbance driven by changes in the solar wind density under northward IMF Bz condition

DOE PAGES

Rout, Diptiranjan; Chakrabarty, D.; Sekar, R.; ...

2016-05-26

Before the onset of a geomagnetic storm on 22 January 2012 (Ap = 24), an enhancement in solar wind number density from 10/cm 3 to 22/cm 3 during 0440–0510 UT under northward interplanetary magnetic field (IMF Bz) condition is shown to have enhanced the high-latitude ionospheric convection and also caused variations in the geomagnetic field globally. Some conspicuous changes in ΔX are observed not only at longitudinally separated low-latitude stations over Indian (prenoon), South American (midnight), Japanese (afternoon), Pacific (afternoon) and African (morning) sectors but also at latitudinally separated stations located over high and middle latitudes. The latitudinal variation ofmore » the amplitude of the ΔX during 0440–0510 UT is shown to be consistent with the characteristics of prompt penetration electric field disturbances. Most importantly, the density pulse event caused enhancements in the equatorial electrojet strength and the peak height of the F layer (h mF 2) over the Indian dip equatorial sector. Furthermore, the concomitant enhancements in electrojet current and F layer movement over the dip equator observed during this space weather event suggest a common driver of prompt electric field disturbance at this time. Such simultaneous variations are found to be absent during magnetically quiet days. In the absence of significant change in solar wind velocity and magnetospheric substorm activity, these observations point toward perceptible prompt electric field disturbance over the dip equator driven by the overcompression of the magnetosphere by solar wind density enhancement.« less

Effect of temperature and flux concentration on soldering of base metal.

PubMed

Lee, S Y; Lin, C T; Wang, M H; Tseng, H; Huang, H M; Dong, D R; Pan, L C; Shih, Y H

2000-12-01

The present study used the acoustic emission (AE) technique to evaluate interactions among soldering temperature, flux treatment, and the resultant ultimate tensile strength (UTS). Scanning electron microscopy (SEM) was used to examine fracture surfaces of the solder joints. Specimens were cast from removable partial denture alloy and then placed in a jig with a gap distance of 1.0 mm. A high-frequency soldering machine with an optical pyrometer was used for soldering at 1150 degrees C and 1200 degrees C, respectively. The flux concentrations were 67% and 75%. The soldered specimens were subjected to tensile test at a crosshead speed of 0.05 mm/min. During testing, acoustic emissions in the frequency range of 100--1200 kHz were collected, filtered, recorded, and processed by a sensing device. The results were analysed by ANOVA and Tukey LSD test. UTS at different temperatures showed no significant difference according to either mechanical or acoustic results. But in the 1200 degrees C group, the UTSs and AE counts showed significant differences (P<0.05) at both flux concentrations. SEM showed that the 1200C group had better dendritic crystal structure than did the 1150 degrees C group. In the 1200 degrees C group specimens with 67% flux had fewer flux inclusion bodies and dendritic crystals than did specimens with 75% flux. The 75% flux subgroup produced high-amplitude (60--70 dB) acoustic signals within the elastic deformation zone, while the 67% flux subgroup produced similar signals within the plastic deformation zone, either beyond the 0.2% yield point or before fracture.

Hydrochemical and Isotopic Composition of The Water Resources In The Po Delta Plain (northern Italy) and Its Environmental Impact

NASA Astrophysics Data System (ADS)

Rapti Caputo, D.; Martinelli, G.

Groundwater samples from wells were collected to examine the hydrochemical char- acteristics and isotopic composition of the water resources in the Ferrara area (delta Po plain). Electrical conductivity (EC), pH, total dissolved solid (TDS), temperature of the water were directly measured in the field. Subsequently, in the laboratory, the samples were analysed for the determination of major ions such as Ca, Mg, K, Na, SO4, Cl, NO3 and HCO3. Also, oxygen, deuterium and tritium isotopic composition, of the same samples were analysed for the isotopic characterisation of the waters. Three principal water groups can be distinguished on the basis of the distribution of the values of 18O and 2H. The first group (A), include the waters from the wells that exploit the unsatured shallow aquifer, developing in mainly sandy or sandy-silty lenses. These are large diameter wells, whose depth does not exceed the 7 m, while their piezometric level is at depth varying between 2 and 3 m from the soil surface. The isotopic composition of such wells is strongly affected by meteorological events (local recharge). Indeed, the main supply to the aquifer occurs through infiltration, mainly from rainwaters and, secondly, from the waters contained in the drainage channels. The hydrochemical characteristics of the waters coming from those wells present a very high sulphate concentration (up to 508 mg/l). To the second group (B) belong the waters with an 18O and 2H content lower than the previously described group and varying, respectively, between -9.6 < 18O < -9.0 and 68.9 < 2H < -64.7. In partic- ular, this group include the waters from the wells exploiting the first confined aquifer sistem, developed in mainly sandy layers. The top of this hydrogeological units, is at a depth varying between 15 and 20 m from the soil surface, while the thickness varies from 20 and 35 m. The waters of this goup present low oxygen values and deuterium and a substantial variation in the traces of tritium with variations from 2.5 to 22.5 +/- 3.9 UT. The low concentration of 2.5 UT, in particular, allows us to evaluate a resi- dence time in underground aquifer for these waters of about 30 years. The high tritium content value of the waters (22.5 +/- 5.6 UT) can be interpreted as mixing phenom- ena between the 'old' waters of the confined aquifer and the 'recent additions' of the network hydrological system situated in the area of the Ferrara plain (Po and Po di Volano rivers). In group C, are the waters of the Po River, where low values can be 1 observed both in oxygen and deuterium contents, with values equal to -9.90 s´ 0.03 and -71.3 s´ 0.9, respectively.

Research Topic | Research Site Name | NREL

Science.gov Websites

exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Capabilities Width of 1746px - Height can , quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Subtopic Heading 2 ex ea commodo consequat. Publications Article Title, Journal Name (Year) Conference Paper Title

Research Staff | Research Site Name | NREL

Science.gov Websites

Research Staff Research Staff Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et , consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. lorem.ipsum

Radio re-brightening of MAXI J1535-571 as it transitions back towards the hard state

NASA Astrophysics Data System (ADS)

Russell, T. D.; Altamirano, D.; Tetarenko, A. J.; Sivakoff, G. R.; Neilsen, J.; Miller-Jones, J. C. A.; van den Eijnden, J.; Jacpot Xrb Collaboration

2017-10-01

As part of an ongoing Australia Telescope Compact Array (ATCA) campaign monitoring the current outburst of MAXI J1535-571, we observed the source on 2017 October 25 between 06:09 UT and 09:24 UT (MJD 58051.32 +/- 0.07).

75 FR 39147 - Establishment of Class E Airspace; Bryce Canyon, UT

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-08

... E airspace at Bryce Canyon, UT, to accommodate aircraft using a new Area Navigation (RNAV) Global Positioning System (GPS) Standard Instrument Approach Procedures (SIAPs) at Bryce Canyon Airport. This will improve the safety and management of Instrument Flight Rules (IFR) operations at the airport. DATES...

ISSE | The University of Tennessee, Knoxville

Science.gov Websites

are leading a study to better understand Appalachian tourism and identify opportunities to grow tourism activities and encourage business development. See the February 8, 2018 article in the UT Daily Beacon, "UT faculty members conduct research on tourism in Appalachia" and the December 18

Deer Creek Dam, Dam, 1,204 feet/238 degrees from intersection of ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Deer Creek Dam, Dam, 1,204 feet/238 degrees from intersection of dam complex access road and U.S. Highway 189 to center of dam, 874 feet/352 degrees from Hydroelectric Powerplant (HAER UT-93-B) to center of dam, Charleston, Wasatch County, UT

Day Jobs/Nightwork: Academic Staff Studying towards Higher Degrees

ERIC Educational Resources Information Center

Winberg, C.; Adams, A.; Esbach, J.; Groenewald, W.; Lakay, D.; Muzondo, I.; Randall, K.; Seane, G.; Siyepu, S.; Veeran, P.

2010-01-01

Universities of Technology (UTs) offer career-focused education in a wide variety of disciplines and fields. Traditionally, UTs recruited academic staff with relevant workplace experience, rather than academic qualifications. The result of this strategy was, while many lecturers possessed professional qualifications in their field, they did not…

Threshold friction velocity of crusted windblown soils in the Columbia Plateau

USDA-ARS?s Scientific Manuscript database

Wind erosion processes are governed by soil physical properties and surface characteristics. Erosion is initiated when the friction velocity exceeds the threshold friction velocity (u*t) of soils. Although u*t is influenced by soil physical properties such as wetness and crusting, there is little in...

Validation of Chlorine and Oxygen Isotope Ratio Analysis to Differentiate Perchlorate Sources and to Document Perchlorate Biodegradation

DTIC Science & Technology

2011-12-01

UCMR) data Hockley County, TX (s)Improper Cathodic Protection Elevated Storage Tank 32 TX Lone Star Army Ammunition Plant Texarkana ...River Army Depot Texarkana , TX Propellant Handling Monitoring Well 80 UT Alliant Tech Systems Magna, UT Rocket Manufacturing Public Water Supply Well

Microsatellite markers and polymorphism in cheatgrass (Bromus tectorum L.)

Treesearch

Alisa P. Ramakrishnan; Craig E. Coleman; Susan E. Meyer; Daniel J. Fairbanks

2001-01-01

Cheatgrass (Bromus tectorum) individuals were genetically characterized using polymorphic microsatellite markers. Through analysis of alleles of five polymorphic loci, genotypes were constructed of individuals from four populations in Utah and Nevada. There were 15 different genotypes: Whiterocks, UT, had nine genotypes, Hobble Creek, UT, had seven genotypes,...

75 FR 62627 - Environmental Impact Statement; Davis County, UT

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-12

... County, UT AGENCY: Federal Highway Administration (FHWA), DOT. ACTION: Notice of Intent. SUMMARY: FWHA is... cooperation with the Utah Department of Transportation (UDOT), will prepare an EIS on a proposal to address... and need and are based on agency and public input. These alternatives include: (1) Taking no action...

Analysis of the Use of Online Tutorial

ERIC Educational Resources Information Center

Fatimah, Fatia; Andriyansah; Wahyuni, Purwaningdyah Murti

2012-01-01

UT (Universitas Terbuka), the open university in Indonesia, is one of the large universities in Indonesia that has more than 300,000 students. UT, as a distance learning education, has conducted online tutorial since 2001. The implementation of an effective and efficient online tutorial depends on three components: students, tutors, and supporting…

34. August, 1971. PHOTOCOPY: GENERAL VIEW OF CITY OF MERCUR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

34. August, 1971. PHOTOCOPY: GENERAL VIEW OF CITY OF MERCUR CA. 1910 (THIS HISTORIC VIEW IS TAKEN FROM A PUBLICATION BY UTAH POWER & LIGHT CO. CREDIT REQUESTED TO COMPANY.). (SEE UT-10-2 FOR PRESENT DAY VIEW). - DeLamar Mercur Mines Company, Golden Gate Mill, Ophir, Tooele County, UT

Nova Centauri 2013 = PNV J13544700-5909080

NASA Astrophysics Data System (ADS)

Waagen, Elizabeth O.

2013-12-01

Announces the discovery of V1369 Cen = Nova Cen 2013 = PNV J13544700-5909080 by John Seach (Chatsworth Island, NSW, Australia) at unfiltered magnitude 5.5 on 2013 December 02.692 UT. Low-resolution spectra obtained by Locke on Dec. 03.3776 UT and by Kaufman on Dec. 03.621 UT show strong Ha and Hb emission lines, indicating the object is a nova. Announced on IAU CBAT Central Bureau Electronic Telegram 3732 (Daniel W. E. Green, ed.). Finder charts with sequences may be created using the AAVSO Variable Star Plotter (http://www.aavso.org/vsp). Observations should be submitted to the AAVSO International Database. See full Alert Notice for more details and observations.

The generic gradient-like structure of certain asymptotically autonomous semilinear parabolic equations

NASA Astrophysics Data System (ADS)

Jänig, A.

2018-05-01

We consider asymptotically autonomous semilinear parabolic equations u_t + Au = f(t,u). Suppose that $f(t,.)\\to f^\\pm$ as $t\\to\\pm\\infty$, where the semiflows induced by \\label{eq:140602-1511} u_t + Au = f^\\pm(u) \\tag{*} are gradient-like. Under certain assumptions, it is shown that generically with respect to a perturbation $g$ with $g(t)\\to 0$ as $|t|\\to\\infty$, every solution of u_t + Au = f(t,u) + g(t) is a connection between equilibria $e^\\pm$ of \\eqref{eq:140602-1511} with $m(e^-)\\geq m(e^+)$. Moreover, if the Morse indices satisfy $m(e^-) = m(e^+)$, then $u$ is isolated by linearization.

Comet C/2012 S1 (ISON)'s carbon-rich and micron-size-dominated coma dust

NASA Astrophysics Data System (ADS)

Wooden, D.; De Buizer, J.; Kelley, M.; Sitko, M.; Woodward, C.; Harker, D.; Reach, W.; Russell, R.; Kim, D.; Yanamadra-Fisher, P.; Lisse, C.; de Pater, I.; Gehrz, R.; Kolokolova, L.

2014-07-01

Comet C/2012 S1 (ISON) was unique in that it was a dynamically new comet derived from the Nearly Isotropic Oort cloud reservoir of comets with a sun-grazing orbit. We present thermal models for comet ISON (r_h ˜ 1.15 au, 2013-Oct-25 11:30 UT) that reveal comet ISON's dust was carbon-rich and dominated by a steep (and therefor narrow) grain size distribution (GSD) dominated by ˜ micron-sized grains. We constrained the models by our SOFIA FORCAST photometry at 11.1, 19.7 and 31.5 μ m and by a silicate feature strength of ˜1.1 and an 8-13 μ m continuum greybody color temperature of ˜275-280 K (using T_{bb}∝ {r}_h^{-0.5} and T_{bb}˜260-265 K from Subaru+COMICS, 2013-Oct-19 UT) [1,2]. Spectra of comet ISON with IRTF+BASS (2013-Nov-11-12 UT) also show a silicate feature strength of ˜1.1 as well as an 11.2 μ m forsterite peak [3]. Our thermal models [6], which employ 0.1-1000 μ m grains, yield constraints for the dust composition as well as GSD parameters of slope, peak grain size, porosity: ISON's dust has a low silicate-to-amorphous carbon ratio (˜1:9), the GSD has a steep slope (N≃4.5), a peak grain radius of ˜0.7 μ m, and moderately porous grains. Specifically, the 8-13 μ m continuum color temperature implies submicron- to micron-size grains and the steep fall off of the SOFIA far-IR photometry requires the GSD to have fewer relative numbers of larger and cooler grains compared to smaller and hotter grains. A IR proxy for the dust production rate is ɛ f ρ ˜ 1500 cm [4], which is akin to but larger than Afρ in scattered light (2013-Oct-20 UT, Afρ=796 cm(±5 %) in V-band from Swift) [5]. Also, ISON had a moderate-to-low dust-to-gas ratio [6]. Comet ISON's dust composition and GSD properties are distinct from the few well-studied long-period Nearly Isotropic Comets (NICs) that all had 'typical' GSD slopes (3.4≤N≤3.7) and silicate-to-amorphous carbon ratios ≫1 as well as the following properties: C/1995 O1 (Hale-Bopp)[7,8,9,10] and C/2001 Q4 (NEAT)[11] had smaller and highly porous grains, whereas C/2007 N4 (Lulin)[12] and C/2006 P1 (McNaught)[13] had larger and compact porous grains. Radial transport to comet-forming disk distances (≥ 20 au) is easier for smaller grains than for larger grains (≤ 1 μ m vs.˜20 μ m-like Stardust terminal particles) [14]. Perhaps Comet ISON formed either earlier in disk evolution whereby larger grains did not have the time to be transported to distances beyond Neptune, or the comet formed so far out in the disk that larger grains did not traverse such large radial distances. The high carbon-content of ISON's refractory dust appears to be complimented by the presence of limited-lifetime organic (CHON-like) grain materials: preliminary analyses of near-IR and high-resolution optical spectra indicate that gas-phase daughter molecules C_2, CN, and CH were more abundant than their parent molecules (HCN, C_2H_2, C_2H_6, measured in the near-IR) [15]. Dust composition as well as grain size distribution parameters (slope, peak grain size, and porosity) give clues to comet origins [16,17].

Normative values of isometric elbow strength in healthy adults: a systematic review.

PubMed

Kotte, Shamala H P; Viveen, Jetske; Koenraadt, Koen L M; The, Bertram; Eygendaal, Denise

2018-07-01

Post-traumatic deformities such as biceps tendon rupture or (peri-)articular fractures of the elbow are often related to a decrease in muscle strength. Postoperative evaluation of these deformities requires normative values of elbow strength. The purpose of this systematic review was to determine these normative values of isometric elbow strength in healthy adults resulting from studies evaluating this strength (i.e. flexion, extension, pronation and supination strength). The databases of PubMed, EMBASE and Web of Sciences were searched and screened for studies involving the isometric elbow strength as measured in asymptomatic volunteers. The quality of the studies was assessed and studies of low quality were excluded. Nineteen studies met the inclusion criteria and were of sufficiently high quality to be included in the present review. In these studies, elbow strength was measured in a total of 1880 healthy volunteers. The experimental set-up and devices used to measure elbow strength varied between studies. Using some assumptions, a normative values table was assembled. Large standard deviations of normative values in combination with different measurement devices used, as well as the different measurement positions of the subjects, demonstrated that there is no consensus about measuring the isometric elbow strength and therefore the normative values have to be interpreted with caution.

Neutrino Interactions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kamyshkov, Yuri; Handler, Thomas

The neutrino group of the University of Tennessee, Knoxville was involved from 05/01/2013 to 04/30/2015 in the neutrino physics research funded by DOE-HEP grant DE-SC0009861. Contributions were made to the Double Chooz nuclear reactor experiment in France where second detector was commissioned during this period and final series of measurements has been started. Although Double Chooz was smaller experimental effort than competitive Daya Bay and RENO experiments, its several advantages make it valuable for understanding of systematic errors in measurements of neutrino oscillations. Double Chooz was the first experiment among competing three that produced initial result for neutrino angle θmore » 13 measurement, giving other experiments the chance to improve measured value statistically. Graduate student Ben Rybolt defended his PhD thesis on the results of Double Chooz experiment in 2015. UT group has fulfilled all the construction and analysis commitments to Double Chooz experiment, and has withdrawn from the collaboration by the end of the mentioned period to start another experiment. Larger effort of UT neutrino group during this period was devoted to the participation in another DOE-HEP project - NOvA experiment. The 14,000-ton "FAR" neutrino detector was commissioned in northern Minnesota in 2014 together with 300-ton "NEAR" detector located at Fermilab. Following that, the physics measurement program has started when Fermilab accelerator complex produced the high-intensity neutrino beam propagating through Earth to detector in MInnessota. UT group contributed to NOvA detector construction and developments in several aspects. Our Research Associate Athanasios Hatzikoutelis was managing (Level 3 manager) the construction of the Detector Control System. This work was successfully accomplished in time with the commissioning of the detectors. Group was involved in the development of the on-line software and study of the signatures of the cosmic ray backgrounds. Flumerfelt and another graduate student Philip Mason were also studying the non-linearity properties of the NOvA liquid scintillator - information that will be essential at the final stages of NOvA data analysis. Philip Mason also studied the response of the FAR NOvA detector in correlation with solar flares. Flumerfelt and Mason successfully defended their PhD in 2015. Also, undergraduate student Cameron Blake Erickson has defended his undergraduate thesis on the NOvA liquid scintillator studies with Compton gamma spectrometer at UT.« less

Composition and Trends of Short-Lived Trace Gases in the UT/LS over Europe Observed by the CARIBIC Aircraft

NASA Astrophysics Data System (ADS)

Baker, A. K.; Brenninkmeijer, C. A.; Oram, D. E.; O'Sullivan, D. A.; Slemr, F.; Schuck, T. J.

2009-12-01

The CARIBIC project (Civil Aircraft for the Regular Investigation of the atmosphere Based on an Instrument Container) involves the monthly deployment of an instrument container equipped to make atmospheric measurements from aboard a commercial airliner, and has operated since 2005 from aboard a Lufthansa Airbus 340-600 . Measurements from the container include in-situ trace gas and aerosol analyses and the collection of aerosol and whole air samples for post-flight laboratory analysis. Measurements made from the sampling flasks include greenhouse gas (GHG), halocarbon and nonmethane hydrocarbon (NMHC) analysis. CARIBIC flights originate in Frankfurt, Germany with routes to India, East Asia, South America, North America and Africa, and typical aircraft cruising altitudes of 10-12km allow for the monitoring of the upper troposphere/lower stratosphere (UT/LS) along these routes. Data collected during the aircraft’s departure from and return to Frankfurt provide a 4 year time series of near-monthly measurements of the composition of the UT/LS above Europe. Here we present a discussion of the composition of short-lived trace gases in the whole air samples collected above Europe during CARIBIC flights. Over 150 air samples were collected between May 2005 and July 2009, or about 4 samples per month. Of the whole air samples collected, about 45% showed influence by stratospheric air (i.e. very low values of GHG, NMHC and halocarbons, elevated O3, high potential vorticity). The remaining samples were representative of the upper troposphere; back trajectories for these samples indicate that a little over half were collected in air masses that had been in the boundary layer within the previous 8 days. The predominant source regions for these samples were the Gulf of Mexico and continental North America. Owing to their wide range of chemical lifetimes and the varying composition of emissions, short-lived trace gases transported to the UT/LS can be useful indicators of source region, photochemical processing and transport timescales of an air mass. Seasonal and longer-term trends in trace gases and trace gas composition are discussed, as well as composition of air masses having different origins. Additionally, we apply relationships between the different species, particularly the NMHC, to gain a qualitative understanding of photochemical processes occurring during transport from the boundary layer to the upper troposphere over Europe.

The Use of Open Educational Resources in Online Learning: A Study of Students' Perception

ERIC Educational Resources Information Center

Harsasi, Meirani

2015-01-01

Universitas Terbuka (UT) is Indonesia's higher education institution which implements distance education system. The term distance implies that learning is not performed face-to-face but there is geographically separation between students and teacher. Therefore, UT must provide many kinds of learning modes and learning support. To facilitate…

Career Support for Students with Disabilities.

ERIC Educational Resources Information Center

Greenberg, Robert M.; Muir, Alan; Gilreath, Crystal

2003-01-01

Career services at the University of Tennessee-Knoxville (UT-Knoxville) had always strived to serve students with disabilities, but didn't know how many students with disabilities actually "were" being served. Then, in the summer of 1998, Alan Muir walked into UT career services and things began to change. This article details how that change came…

76 FR 40354 - Environmental Impacts Statements; Notice of Availability

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-08

.... 20110216, Final EIS, FHWA, UT, Hyde Park/North Logan Corridor Project, Proposed 200 East Transportation Corridor between North Logan City and Hyde Park, Funding, Right-of-Way Acquisitions and US Army COE Section 404 Permit, Cache County, UT, Review Period Ends: 08/08/2011, Contact: Paul C. Ziman 801-955-3525...

78 FR 45848 - Amendment of Class E Airspace; Salt Lake City, UT

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-30

... Salt Lake City, UT, to accommodate aircraft using Area Navigation (RNAV) Global Positioning System (GPS) and Instrument Landing System (ILS) or Localizer (LOC) standard instrument approach procedures at Salt..., and makes a minor change to the legal description of Class E airspace extending upward from 1,200 feet...

Pragmatic Exchanges and Cooperation to Prepare Quality Engineers and Technologists

ERIC Educational Resources Information Center

Lee, Lung-Sheng

2014-01-01

The mission of national colleges of technology (NCT's) in Japan and the universities of technology (UT's) in Taiwan is to pragmatically prepare quality engineers and technologists. In recent years, the partnership among NCT's and UT's is extended and expanded. This paper introduces the pragmatic and successful partnership between National United…

75 FR 75492 - Notice of Realty Action; Recreation and Public Purposes Act Classification, San Juan County, UT

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-03

...-87677] Notice of Realty Action; Recreation and Public Purposes Act Classification, San Juan County, UT... Management (BLM) has examined and found suitable for classification for lease or conveyance to the Utah... regarding this proposed classification until January 18, 2011. ADDRESSES: Comments may be submitted to the...

78 FR 2434 - Notice of Inventory Completion: Natural History Museum of Utah, Salt Lake City, UT

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-11

... Inventory Completion: Natural History Museum of Utah, Salt Lake City, UT AGENCY: National Park Service, Interior. ACTION: Notice. SUMMARY: The Natural History Museum of Utah has completed an inventory of human... culturally affiliated with the human remains and associated funerary objects may contact the Natural History...

78 FR 2430 - Notice of Inventory Completion: Natural History Museum of Utah, Salt Lake City, UT

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-11

... Inventory Completion: Natural History Museum of Utah, Salt Lake City, UT AGENCY: National Park Service, Interior. ACTION: Notice. SUMMARY: The Natural History Museum of Utah has completed an inventory of human... culturally affiliated with the human remains and associated funerary objects may contact the Natural History...

77 FR 52057 - Notice of Inventory Completion: Brigham Young University, Museum of Peoples and Cultures, Provo...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-28

... Inventory Completion: Brigham Young University, Museum of Peoples and Cultures, Provo, UT; Correction AGENCY... Museum of Peoples and Cultures, Provo, UT. The human remains and associated funerary objects were removed... 1971, the human remains were donated to the Museum of Peoples and Cultures and were accessioned...

Conscious and unconscious thought in risky choice: testing the capacity principle and the appropriate weighting principle of unconscious thought theory.

PubMed

Ashby, Nathaniel J S; Glöckner, Andreas; Dickert, Stephan

2011-01-01

Daily we make decisions ranging from the mundane to the seemingly pivotal that shape our lives. Assuming rationality, all relevant information about one's options should be thoroughly examined in order to make the best choice. However, some findings suggest that under specific circumstances thinking too much has disadvantageous effects on decision quality and that it might be best to let the unconscious do the busy work. In three studies we test the capacity assumption and the appropriate weighting principle of Unconscious Thought Theory using a classic risky choice paradigm and including a "deliberation with information" condition. Although we replicate an advantage for unconscious thought (UT) over "deliberation without information," we find that "deliberation with information" equals or outperforms UT in risky choices. These results speak against the generality of the assumption that UT has a higher capacity for information integration and show that this capacity assumption does not hold in all domains. Furthermore, we show that "deliberate thought with information" leads to more differentiated knowledge compared to UT which speaks against the generality of the appropriate weighting assumption.

Regulation of Renal Urea Transport by Vasopressin

PubMed Central

Sands, Jeff M.; Blount, Mitsi A.; Klein, Janet D.

2011-01-01

Terrestrial life would be miserable without the ability to concentrate urine. Production of concentrated urine requires complex interactions among the nephron segments and vasculature in the kidney medulla. In addition to water channels (aquaporins) and sodium transporters, urea transporters are critically important to the theories proposed to explain the physiologic processes occurring when urine is concentrated. Vasopressin (anti-diuretic hormone) is the key hormone regulating the production of concentrated urine. Vasopressin rapidly increases water and urea transport in the terminal inner medullary collecting duct (IMCD). Vasopressin rapidly increases urea permeability in the IMCD through increases in phosphorylation and apical plasma-membrane accumulation of the urea transporter A1 (UT-A1). Vasopressin acts through two cAMP-dependent signaling pathways in the IMCD: protein kinase A and exchange protein activated by cAMP Epac. Protein kinase A phosphorylates UT-A1 at serines 486 and 499. In summary, vasopressin regulates urea transport acutely by increasing UT-A1 phosphorylation and the apical plasma-membrane accumulation of UT-A1 through two cAMP-dependent pathways. PMID:21686211

Novel FR-900493 Analogues That Inhibit the Outgrowth of Clostridium difficile Spores

PubMed Central

2018-01-01

The spectrum of antibacterial activity for the nucleoside antibiotic FR-900493 (1) can be extended by chemical modifications. We have generated a small focused library based on the structure of 1 and identified UT-17415 (9), UT-17455 (10), UT-17460 (11), and UT-17465 (12), which exhibit anti-Clostridium difficile growth inhibitory activity. These analogues also inhibit the outgrowth of C. difficile spores at 2× minimum inhibitory concentration. One of these analogues, 11, relative to 1 exhibits over 180-fold and 15-fold greater activity against the enzymes, phospho-MurNAc-pentapeptide translocase (MraY) and polyprenyl phosphate-GlcNAc-1-phosphate transferase (WecA), respectively. The phosphotransferase inhibitor 11 displays antimicrobial activity against several tested bacteria including Bacillus subtilis, Clostridium spp., and Mycobacterium smegmatis, but no growth inhibitory activity is observed against the other Gram-positive and Gram-negative bacteria. The selectivity index (Vero cell cytotoxicity/C. difficileantimicrobial activity) of 11 is approximately 17, and 11 does not induce hemolysis even at a 100 μM concentration. PMID:29503973

Effective four-fermion operators in top physics: A roadmap

NASA Astrophysics Data System (ADS)

Aguilar-Saavedra, J. A.

2011-02-01

We write down a minimal basis for dimension-six gauge-invariant four-fermion operators, with some operator replacements with respect to previous ones which make it simpler for calculations. Using this basis we classify all four-fermion operator contributions involving one or two top quarks. Taking into account the different fermion chiralities, possible colour contractions and independent flavour combinations, a total number of 572 gauge-invariant operators are involved. We apply this to calculate all three-body top decay widths t→dud, t→dei+ν, t→uuu, t→uej+ei-, t→uνν (with i,j,k generation indices) mediated by dimension-six four-fermion operators, including the interference with the Standard Model amplitudes when present. All single top production cross sections in pp, pp¯ and ee collisions are calculated as well, namely ud→dt, dd→ut, ud→dt, uu→ut, uu→ut, ee→ut and the charge conjugate processes. We also compute all top pair production cross sections, uu→tt¯, dd→tt¯, uu→tt and ee→tt¯. Our results are completely general, without assuming any particular relation among effective operator coefficients.