Restoring method for missing data of spatial structural stress monitoring based on correlation

NASA Astrophysics Data System (ADS)

Zhang, Zeyu; Luo, Yaozhi

2017-07-01

Long-term monitoring of spatial structures is of great importance for the full understanding of their performance and safety. The missing part of the monitoring data link will affect the data analysis and safety assessment of the structure. Based on the long-term monitoring data of the steel structure of the Hangzhou Olympic Center Stadium, the correlation between the stress change of the measuring points is studied, and an interpolation method of the missing stress data is proposed. Stress data of correlated measuring points are selected in the 3 months of the season when missing data is required for fitting correlation. Data of daytime and nighttime are fitted separately for interpolation. For a simple linear regression when single point's correlation coefficient is 0.9 or more, the average error of interpolation is about 5%. For multiple linear regression, the interpolation accuracy is not significantly increased after the number of correlated points is more than 6. Stress baseline value of construction step should be calculated before interpolating missing data in the construction stage, and the average error is within 10%. The interpolation error of continuous missing data is slightly larger than that of the discrete missing data. The data missing rate of this method should better not exceed 30%. Finally, a measuring point's missing monitoring data is restored to verify the validity of the method.

12 CFR 327.9 - Assessment pricing methods.

Code of Federal Regulations, 2013 CFR

2013-01-01

...: Capital adequacy—25%, Asset quality—20%, Management—25%, Earnings—10%, Liquidity—10%, and Sensitivity to... Asset-Related Stress 50 Tier 1 Leverage Ratio 10 Concentration Measure 35 Core Earnings/Average Quarter-End Total Assets * 20 Credit Quality Measure 35 P.3 Ability to Withstand Funding-Related Stress 20...

12 CFR 327.9 - Assessment pricing methods.

Code of Federal Regulations, 2014 CFR

2014-01-01

...: Capital adequacy—25%, Asset quality—20%, Management—25%, Earnings—10%, Liquidity—10%, and Sensitivity to... Asset-Related Stress 50 Tier 1 Leverage Ratio 10 Concentration Measure 35 Core Earnings/Average Quarter-End Total Assets * 20 Credit Quality Measure 35 P.3 Ability to Withstand Funding-Related Stress 20...

Post-Traumatic Stress Disorder in Young People with Intellectual Disability

ERIC Educational Resources Information Center

Turk, J.; Robbins, I.; Woodhead, M.

2005-01-01

Background: Post-traumatic stress disorder (PTSD) is common and treatable. There is extensive research on people of average intelligence yet little on individuals with developmental disabilities. Methods: We report two people with intellectual disability (ID) who experienced PTSD. The relevance of their developmental difficulties, social and…

Turbulence modeling for hypersonic flows

NASA Technical Reports Server (NTRS)

Marvin, J. G.; Coakley, T. J.

1989-01-01

Turbulence modeling for high speed compressible flows is described and discussed. Starting with the compressible Navier-Stokes equations, methods of statistical averaging are described by means of which the Reynolds-averaged Navier-Stokes equations are developed. Unknown averages in these equations are approximated using various closure concepts. Zero-, one-, and two-equation eddy viscosity models, algebraic stress models and Reynolds stress transport models are discussed. Computations of supersonic and hypersonic flows obtained using several of the models are discussed and compared with experimental results. Specific examples include attached boundary layer flows, shock wave boundary layer interactions and compressible shear layers. From these examples, conclusions regarding the status of modeling and recommendations for future studies are discussed.

Integrated In Situ Stress Estimation by Hydraulic Fracturing, Borehole Observations and Numerical Analysis at the EXP-1 Borehole in Pohang, Korea

NASA Astrophysics Data System (ADS)

Kim, Hanna; Xie, Linmao; Min, Ki-Bok; Bae, Seongho; Stephansson, Ove

2017-12-01

It is desirable to combine the stress measurement data produced by different methods to obtain a more reliable estimation of in situ stress. We present a regional case study of integrated in situ stress estimation by hydraulic fracturing, observations of borehole breakouts and drilling-induced fractures, and numerical modeling of a 1 km-deep borehole (EXP-1) in Pohang, South Korea. Prior to measuring the stress, World Stress Map (WSM) and modern field data in the Korean Peninsula are used to construct a best estimate stress model in this area. Then, new stress data from hydraulic fracturing and borehole observations is added to determine magnitude and orientation of horizontal stresses. Minimum horizontal principal stress is estimated from the shut-in pressure of the hydraulic fracturing measurement at a depth of about 700 m. The horizontal stress ratios ( S Hmax/ S hmin) derived from hydraulic fracturing, borehole breakout, and drilling-induced fractures are 1.4, 1.2, and 1.1-1.4, respectively, and the average orientations of the maximum horizontal stresses derived by field methods are N138°E, N122°E, and N136°E, respectively. The results of hydraulic fracturing and borehole observations are integrated with a result of numerical modeling to produce a final rock stress model. The results of the integration give in situ stress ratios of 1.3/1.0/0.8 ( S Hmax/ S V/ S hmin) with an average azimuth of S Hmax in the orientation range of N130°E-N136°E. It is found that the orientation of S Hmax is deviated by more than 40° clockwise compared to directions reported for the WSM in southeastern Korean peninsula.

Meta-Analysis of Dropout in Treatments for Posttraumatic Stress Disorder

ERIC Educational Resources Information Center

Imel, Zac E.; Laska, Kevin; Jakupcak, Matthew; Simpson, Tracy L.

2013-01-01

Objective: Many patients drop out of treatments for posttraumatic stress disorder (PTSD); some clinicians believe that trauma-focused treatments increase dropout. Method: We conducted a meta-analysis of dropout among active treatments in clinical trials for PTSD (42 studies; 17 direct comparisons). Results: The average dropout rate was 18%, but it…

[Contact characteristics research of acetabular weight-bearing area with different internal fixation methods after compression fracture of acetabular dome].

PubMed

Xu, Bowen; Zhang, Qingsong; An, Siqi; Pei, Baorui; Wu, Xiaobo

2017-08-01

To establish the model of compression fracture of acetabular dome, and to measure the contact characteristics of acetabular weight-bearing area of acetabulum after 3 kinds of internal fixation. Sixteen fresh adult half pelvis specimens were randomly divided into 4 groups, 4 specimens each group. Group D was the complete acetabulum (control group), and the remaining 3 groups were prepared acetabular dome compression fracture model. The fractures were fixed with reconstruction plate in group A, antegrade raft screws in group B, and retrograde raft screws in group C. The pressure sensitive films were attached to the femoral head, and the axial compression test was carried out on the inverted single leg standing position. The weight-bearing area, average stress, and peak stress were measured in each group. Under the loading of 500 N, the acetabular weight-bearing area was significantly higher in group D than in other 3 groups ( P <0.05), and the average stress and peak stress were significantly lower than in other 3 groups ( P <0.05). The acetabular weight-bearing area were significantly higher in group B and group C than in group A, and the average stress and peak stress were significantly lower than in group A ( P <0.05). There was no significant difference in the above indexes between group B and group C ( P >0.05). For the compression fracture of the acetabular dome, the contact characteristics of the weight-bearing area can not restore to the normal level, even if the anatomical reduction and rigid internal fixation were performed; compared with the reconstruction plate fixation, antegrade and retrograde raft screws fixations can increase the weight-bearing area, reduce the average stress and peak stress, and reduce the incidence of traumatic arthritis.

Sleep quantity, quality, and insomnia symptoms of medical students during clinical years

PubMed Central

Alsaggaf, Mohammed A.; Wali, Siraj O.; Merdad, Roah A.; Merdad, Leena A.

2016-01-01

Objectives: To determine sleep habits and sleep quality in medical students during their clinical years using validated measures; and to investigate associations with academic performance and psychological stress. Methods: In this cross-sectional study, medical students (n=320) were randomly selected from a list of all enrolled clinical-year students in a Saudi medical school from 2011-2012. Students filled a questionnaire including demographic and lifestyle factors, Pittsburgh Sleep Quality Index, Epworth Sleepiness Scale, and Perceived Stress Scale. Results: Students acquired on average, 5.8 hours of sleep each night, with an average bedtime at 01:53. Approximately 8% reported acquiring sleep during the day, and not during nighttime. Poor sleep quality was present in 30%, excessive daytime sleepiness (EDS) in 40%, and insomnia symptoms in 33% of students. Multivariable regression models revealed significant associations between stress, poor sleep quality, and EDS. Poorer academic performance and stress were associated with symptoms of insomnia. Conclusion: Sleep deprivation, poor sleep quality, and EDS are common among clinical years medical students. High levels of stress and the pressure of maintaining grade point averages may be influencing their quality of sleep. PMID:26837401

Quantification of wall shear stress in large blood vessels using Lagrangian interpolation functions with cine phase-contrast magnetic resonance imaging.

PubMed

Cheng, Christopher P; Parker, David; Taylor, Charles A

2002-09-01

Arterial wall shear stress is hypothesized to be an important factor in the localization of atherosclerosis. Current methods to compute wall shear stress from magnetic resonance imaging (MRI) data do not account for flow profiles characteristic of pulsatile flow in noncircular vessel lumens. We describe a method to quantify wall shear stress in large blood vessels by differentiating velocity interpolation functions defined using cine phase-contrast MRI data on a band of elements in the neighborhood of the vessel wall. Validation was performed with software phantoms and an in vitro flow phantom. At an image resolution corresponding to in vivo imaging data of the human abdominal aorta, time-averaged, spatially averaged wall shear stress for steady and pulsatile flow were determined to be within 16% and 23% of the analytic solution, respectively. These errors were reduced to 5% and 8% with doubling in image resolution. For the pulsatile software phantom, the oscillation in shear stress was predicted to within 5%. The mean absolute error of circumferentially resolved shear stress for the nonaxisymmetric phantom decreased from 28% to 15% with a doubling in image resolution. The irregularly shaped phantom and in vitro investigation demonstrated convergence of the calculated values with increased image resolution. We quantified the shear stress at the supraceliac and infrarenal regions of a human abdominal aorta to be 3.4 and 2.3 dyn/cm2, respectively.

Analysis and Development of Finite Element Methods for the Study of Nonlinear Thermomechanical Behavior of Structural Components

NASA Technical Reports Server (NTRS)

Oden, J. Tinsley

1995-01-01

Underintegrated methods are investigated with respect to their stability and convergence properties. The focus was on identifying regions where they work and regions where techniques such as hourglass viscosity and hourglass control can be used. Results obtained show that underintegrated methods typically lead to finite element stiffness with spurious modes in the solution. However, problems exist (scalar elliptic boundary value problems) where underintegrated with hourglass control yield convergent solutions. Also, stress averaging in underintegrated stiffness calculations does not necessarily lead to stable or convergent stress states.

College Freshman Stress and Weight Change: Differences by Gender

ERIC Educational Resources Information Center

Economos, Christina D.; Hildebrandt, M. Lise; Hyatt, Raymond R.

2008-01-01

Objectives: To examine how stress and health-related behaviors affect freshman weight change by gender. Methods: Three hundred ninety-six freshmen completed a 40-item health behavior survey and height and weight were collected at baseline and follow-up. Results: Average weight change was 5.04 lbs for males, 5.49 lbs for females. Weight gain was…

Impact of Hybrid Delivery of Education on Student Academic Performance and the Student Experience

PubMed Central

Nutter, Douglas A.; Charneski, Lisa; Butko, Peter

2009-01-01

Objectives To compare student academic performance and the student experience in the first-year doctor of pharmacy (PharmD) program between the main and newly opened satellite campuses of the University of Maryland. Methods Student performance indicators including graded assessments, course averages, cumulative first-year grade point average (GPA), and introductory pharmacy practice experience (IPPE) evaluations were analyzed retrospectively. Student experience indicators were obtained via an online survey instrument and included involvement in student organizations; time-budgeting practices; and stress levels and their perceived effect on performance. Results Graded assessments, course averages, GPA, and IPPE evaluations were indistinguishable between campuses. Students' time allocation was not different between campuses, except for time spent attending class and watching lecture videos. There was no difference between students' stress levels at each campus. Conclusions The implementation of a satellite campus to expand pharmacy education yielded academic performance and student engagement comparable to those from traditional delivery methods. PMID:19960080

The effect of neuro-linguistic programming on occupational stress in critical care nurses

PubMed Central

HemmatiMaslakpak, Masumeh; Farhadi, Masumeh; Fereidoni, Javid

2016-01-01

Background: The use of coping strategies in reducing the adverse effects of stress can be helpful. Nero-linguistic programming (NLP) is one of the modern methods of psychotherapy. This study aimed to determine the effect of NLP on occupational stress in nurses working in critical care units of Urmia. Materials and Methods: This study was carried out quasi-experimentally (before–after) with control and experimental groups. Of all the nurses working in the critical care units of Urmia Imam Khomeini and Motahari educational/therapeutic centers, 60 people participated in this survey. Eighteen sessions of intervention were done, each for 180 min. The experimental group received NLP program (such as goal setting, time management, assertiveness skills, representational system, and neurological levels, as well as some practical and useful NLP techniques). Expanding Nursing Stress Scale (ENSS) was used as the data gathering tool. Data were analyzed using SPSS version 16. Descriptive statistics and Chi-square test, Mann–Whitney test, and independent t-test were used to analyze the data. Results: The baseline score average of job stress was 120.88 and 121.36 for the intervention and control groups, respectively (P = 0.65). After intervention, the score average of job stress decreased to 64.53 in the experimental group while that of control group remained relatively unchanged (120.96). Mann–Whitney test results showed that stress scores between the two groups was statistically significant (P = 0.0001). Conclusions: The results showed that the use of NLP can increase coping with stressful situations, and it can reduce the adverse effects of occupational stress. PMID:26985221

Effect of crack curvature on stress intensity factors for ASTM standard compact tension specimens

NASA Technical Reports Server (NTRS)

Alam, J.; Mendelson, A.

1983-01-01

The stress intensity factors (SIF) are calculated using the method of lines for the compact tension specimen in tensile and shear loading for curved crack fronts. For the purely elastic case, it was found that as the crack front curvature increases, the SIF value at the center of the specimen decreases while increasing at the surface. For the higher values of crack front curvatures, the maximum value of the SIF occurs at an interior point located adjacent to the surface. A thickness average SIF was computed for parabolically applied shear loading. These results were used to assess the requirements of ASTM standards E399-71 and E399-81 on the shape of crack fronts. The SIF is assumed to reflect the average stress environment near the crack edge.

A method to quantify hand-transmitted vibration exposure based on the biodynamic stress concept.

PubMed

Dong, R G; Welcome, D E; Wu, J Z

2007-11-01

This study generally hypothesized that the vibration-induced biodynamic stress and number of its cycles in a substructure of the hand-arm system play an important role in the development of vibration-induced disorders in the substructure. As the first step to test this hypothesis, the specific aims of this study were to develop a practical method to quantify the biodynamic stress-cycle measure, to compare it with ISO-weighted and unweighted accelerations, and to assess its potential for applications. A mechanical-equivalent model of the system was established using reported experimental data. The model was used to estimate the average stresses in the fingers and palm. The frequency weightings of the stresses in these substructures were derived using the proposed stress-cycle measure. This study found the frequency dependence of the average stress distributed in the fingers is different from that in the palm. Therefore, this study predicted that the frequency dependencies of finger disorders could also be different from those of the disorders in the palm, wrist, and arms. If vibration-induced white finger (VWF) is correlated better with unweighted acceleration than with ISO-weighted acceleration, the biodynamic stress distributed in the fingers is likely to play a more important role in the development of VWF than is th e biodynamic stressdistributed in the other substructures of the hand-arm system. The results of this study also suggest that the ISO weighting underestimates the high-frequency effect on the finger disorder development but it may provide a reasonable risk assessment of the disorders in the wrist and arm.

Comparison and verification of two models which predict minimum principal in situ stress from triaxial data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harikrishnan, R.; Hareland, G.; Warpinski, N.R.

This paper evaluates the correlation between values of minimum principal in situ stress derived from two different models which use data obtained from triaxial core tests and coefficient for earth at rest correlations. Both models use triaxial laboratory tests with different confining pressures. The first method uses a vcrified fit to the Mohr failure envelope as a function of average rock grain size, which was obtained from detailed microscopic analyses. The second method uses the Mohr-Coulomb failure criterion. Both approaches give an angle in internal friction which is used to calculate the coefficient for earth at rest which gives themore » minimum principal in situ stress. The minimum principal in situ stress is then compared to actual field mini-frac test data which accurately determine the minimum principal in situ stress and are used to verify the accuracy of the correlations. The cores and the mini-frac stress test were obtained from two wells, the Gas Research Institute`s (GRIs) Staged Field Experiment (SFE) no. 1 well through the Travis Peak Formation in the East Texas Basin, and the Department of Energy`s (DOE`s) Multiwell Experiment (MWX) wells located west-southwest of the town of Rifle, Colorado, near the Rulison gas field. Results from this study indicates that the calculated minimum principal in situ stress values obtained by utilizing the rock failure envelope as a function of average rock grain size correlation are in better agreement with the measured stress values (from mini-frac tests) than those obtained utilizing Mohr-Coulomb failure criterion.« less

Quantifying the Physiological Stress Response to Simulated Maritime Pilotage Tasks

PubMed Central

Main, Luana C.; Wolkow, Alexander; Chambers, Timothy P.

2017-01-01

Objective: The aim of this study was to quantify the stress associated with performing maritime pilotage tasks in a high-fidelity simulator. Methods: Eight trainee and 13 maritime pilots completed two simulated pilotage tasks of varying complexity. Salivary cortisol samples were collected pre- and post-simulation for both trials. Heart rate was measured continuously throughout the study. Results: Significant changes in salivary cortisol (P = 0.000, η2 = 0.139), average (P = 0.006, η2 = 0.087), and peak heart rate (P = 0.013, η2 = 0.077) from pre- to postsimulation were found. Varying task complexity did partially influence stress response; average (P = 0.016, η2 = 0.026) and peak heart rate (P = 0.034, η2 = 0.020) were higher in the experimental condition. Trainees also recorded higher average (P = 0.000, η2 = 0.054) and peak heart rates (P = 0.027, η2 = 0.022). Conclusion: Performing simulated pilotage tasks evoked a measurable stress response in both trainee and expert maritime pilots. PMID:28922309

Modelling and analysis of the stress distribution in a multi-thin film system Pt/USG/Si

NASA Astrophysics Data System (ADS)

Yao, W. Z.; Roqueta, F.; Craveur, J. C.; Belhenini, S.; Gardes, P.; Tougui, A.

2018-04-01

Residual stress analysis is commonly achieved through curvature measurement with the help of Stoney’s formula. However, this conventional approach is inadequate for multi-layer thin film systems, which are widely used in today’s microelectronics. Also, for the thin film case, the residual stress is composed of thermal stress and intrinsic stress. Measuring the wafer curvature at room temperature provides a value for the average stresses in the layer, the two components cannot be distinguished by the existing methodologies of curvature measurement. To alleviate these problems, a modified curvature method combining finite element (FE) modelling is proposed to study the stress distribution in a Pt/USG/Si structure. A 2D FE model is firstly built in order to calculate the thermal stress in the multilayer structure, the obtained thermal stresses in respective films are verified by an analytical model. Then, we calculate the warpage of the multilayer structure by considering the intrinsic stress in the respective films. The residual stresses in the films are determined by minimizing the difference between the simulated warpage and that of experimental measurement. The proposed approach can be used to calculate not only the average residual stress but also thermal and intrinsic stress components in the USG and Platinum films. The obtained residual and intrinsic stresses from a numerical model are compared with the values of other studies. There is no limitation for the application of our methodologies regarding the number of the layers in the stack.

Differences in the stress distribution in the distal femur between patellofemoral joint replacement and total knee replacement: a finite element study

PubMed Central

2012-01-01

Background Patellofemoral joint replacement is a successful treatment option for isolated patellofemoral osteoarthritis. However, results of later conversion to total knee replacement may be compromised by periprosthetic bone loss. Previous clinical studies have demonstrated a decrease in distal femoral bone mineral density after patellofemoral joint replacement. It is unclear whether this is due to periprosthetic stress shielding. The main objective of the current study was to evaluate the stress shielding effect of prosthetic replacement with 2 different patellofemoral prosthetic designs and with a total knee prosthesis. Methods We developed a finite element model of an intact patellofemoral joint, and finite element models of patellofemoral joint replacement with a Journey PFJ prosthesis, a Richards II prosthesis, and a Genesis II total knee prosthesis. For each of these 4 finite element models, the average Von Mises stress in 2 clinically relevant regions of interest were evaluated during a simulated squatting movement until 120 degrees of flexion. Results During deep knee flexion, in the anterior region of interest, the average Von Mises stress with the Journey PFJ design was comparable to the physiological knee, while reduced by almost 25% for both the Richards II design and the Genesis II total knee joint replacement design. The average Von Mises stress in the supracondylar region of interest was similar for both patellofemoral prosthetic designs and the physiological model, with slightly lower stress for the Genesis II design. Conclusions Patellofemoral joint replacement results in periprosthetic stress-shielding, although to a smaller degree than in total knee replacement. Specific patellofemoral prosthetic design properties may result in differences in femoral stress shielding. PMID:22704638

Measurement of regional compliance using 4DCT images for assessment of radiation treatment1

PubMed Central

Zhong, Hualiang; Jin, Jian-yue; Ajlouni, Munther; Movsas, Benjamin; Chetty, Indrin J.

2011-01-01

Purpose: Radiation-induced damage, such as inflammation and fibrosis, can compromise ventilation capability of local functional units (alveoli) of the lung. Ventilation function as measured with ventilation images, however, is often complicated by the underlying mechanical variations. The purpose of this study is to present a 4DCT-based method to measure the regional ventilation capability, namely, regional compliance, for the evaluation of radiation-induced lung damage. Methods: Six 4DCT images were investigated in this study: One previously used in the generation of a POPI model and the other five acquired at Henry Ford Health System. A tetrahedral geometrical model was created and scaled to encompass each of the 4DCT image domains. Image registrations were performed on each of the 4DCT images using a multiresolution Demons algorithm. The images at the end of exhalation were selected as a reference. Images at other exhalation phases were registered to the reference phase. For the POPI-modeled patient, each of these registration instances was validated using 40 landmarks. The displacement vector fields (DVFs) were used first to calculate the volumetric variation of each tetrahedron, which represents the change in the air volume. The calculated results were interpolated to generate 3D ventilation images. With the computed DVF, a finite element method (FEM) framework was developed to compute the stress images of the lung tissue. The regional compliance was then defined as the ratio of the ventilation and stress values and was calculated for each phase. Based on iterative FEM simulations, the potential range of the mechanical parameters for the lung was determined by comparing the model-computed average stress to the clinical reference value of airway pressure. The effect of the parameter variations on the computed stress distributions was estimated using Pearson correlation coefficients. Results: For the POPI-modeled patient, five exhalation phases from the start to the end of exhalation were denoted by Pi, i=1,…,5, respectively. The average lung volume variation relative to the reference phase (P5) was reduced from 18% at P1 to 4.8% at P4. The average stress at phase Pi was 1.42, 1.34, 0.74, and 0.28 kPa, and the average regional compliance was 0.19, 0.20, 0.20, and 0.24 for i=1,…,4, respectively. For the other five patients, their average Rv value at the end-inhalation phase was 21.1%, 19.6%, 22.4%, 22.5%, and 18.8%, respectively, and the regional compliance averaged over all six patients is 0.2. For elasticity parameters chosen from the potential parameter range, the resultant stress distributions were found to be similar to each other with Pearson correlation coefficients greater than 0.81. Conclusions: A 4DCT-based mechanical model has been developed to calculate the ventilation and stress images of the lung. The resultant regional compliance represents the lung’s elasticity property and is potentially useful in correlating regions of lung damage with radiation dose following a course of radiation therapy. PMID:21520868

Measurement of regional compliance using 4DCT images for assessment of radiation treatment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhong Hualiang; Jin Jianyue; Ajlouni, Munther

2011-03-15

Purpose: Radiation-induced damage, such as inflammation and fibrosis, can compromise ventilation capability of local functional units (alveoli) of the lung. Ventilation function as measured with ventilation images, however, is often complicated by the underlying mechanical variations. The purpose of this study is to present a 4DCT-based method to measure the regional ventilation capability, namely, regional compliance, for the evaluation of radiation-induced lung damage. Methods: Six 4DCT images were investigated in this study: One previously used in the generation of a POPI model and the other five acquired at Henry Ford Health System. A tetrahedral geometrical model was created and scaledmore » to encompass each of the 4DCT image domains. Image registrations were performed on each of the 4DCT images using a multiresolution Demons algorithm. The images at the end of exhalation were selected as a reference. Images at other exhalation phases were registered to the reference phase. For the POPI-modeled patient, each of these registration instances was validated using 40 landmarks. The displacement vector fields (DVFs) were used first to calculate the volumetric variation of each tetrahedron, which represents the change in the air volume. The calculated results were interpolated to generate 3D ventilation images. With the computed DVF, a finite element method (FEM) framework was developed to compute the stress images of the lung tissue. The regional compliance was then defined as the ratio of the ventilation and stress values and was calculated for each phase. Based on iterative FEM simulations, the potential range of the mechanical parameters for the lung was determined by comparing the model-computed average stress to the clinical reference value of airway pressure. The effect of the parameter variations on the computed stress distributions was estimated using Pearson correlation coefficients. Results: For the POPI-modeled patient, five exhalation phases from the start to the end of exhalation were denoted by P{sub i}, i=1,...,5, respectively. The average lung volume variation relative to the reference phase (P{sub 5}) was reduced from 18% at P{sub 1} to 4.8% at P{sub 4}. The average stress at phase P{sub i} was 1.42, 1.34, 0.74, and 0.28 kPa, and the average regional compliance was 0.19, 0.20, 0.20, and 0.24 for i=1,...,4, respectively. For the other five patients, their average R{sub v} value at the end-inhalation phase was 21.1%, 19.6%, 22.4%, 22.5%, and 18.8%, respectively, and the regional compliance averaged over all six patients is 0.2. For elasticity parameters chosen from the potential parameter range, the resultant stress distributions were found to be similar to each other with Pearson correlation coefficients greater than 0.81. Conclusions: A 4DCT-based mechanical model has been developed to calculate the ventilation and stress images of the lung. The resultant regional compliance represents the lung's elasticity property and is potentially useful in correlating regions of lung damage with radiation dose following a course of radiation therapy.« less

Influence of lithostatic stress on earthquake stress drops in North America

USGS Publications Warehouse

Boyd, Oliver; McNamara, Daniel E.; Hartzell, Stephen; Choy, George

2017-01-01

We estimate stress drops for earthquakes in and near the continental United States using the method of spectral ratios. The ratio of acceleration spectra between collocated earthquakes recorded at a given station removes the effects of path and recording site and yields source parameters including corner frequency for, and the ratio of seismic moment between, the two earthquakes. We determine stress drop from these parameters for 1121 earthquakes greater than M∼3 in 60 earthquake clusters. We find that the average Brune stress drop for the few eastern United States (EUS) tectonic mainshocks studied (2.6–36 MPa) is about three times greater than that of tectonic mainshocks in the western United States (WUS, 1.0–7.9 MPa) and five times greater than mainshocks potentially induced by wastewater injection in the central United States (CUS, 0.6–5.6 MPa). EUS events tend to be deeper thrusting events, whereas WUS events tend to be shallower but have a wide range of focal mechanisms. CUS events tend to be shallow with strike‐slip to normal‐faulting mechanisms. With the possible exception of CUS aftershocks, we find that differences in stress drop among all events can be taken into account, within one standard deviation of significance, by differences in the shear failure stress as outlined by Mohr–Coulomb theory. The shear failure stress is a function of vertical stress (or depth), the fault style (normal, strike slip, or reverse), and coefficient of friction (estimated here to be, on average, 0.64). After accounting for faulting style and depth dependence, we find that the average Brune stress drop is about 3% of the failure stress. These results suggest that high‐frequency shaking hazard (>∼1  Hz) from shallow induced events and aftershocks is reduced to some extent by lower stress drop. However, the shallow hypocenters will increase hazard within several kilometers of the source.

A Note on Spatial Averaging and Shear Stresses Within Urban Canopies

NASA Astrophysics Data System (ADS)

Xie, Zheng-Tong; Fuka, Vladimir

2018-04-01

One-dimensional urban models embedded in mesoscale numerical models may place several grid points within the urban canopy. This requires an accurate parametrization for shear stresses (i.e. vertical momentum fluxes) including the dispersive stress and momentum sinks at these points. We used a case study with a packing density of 33% and checked rigorously the vertical variation of spatially-averaged total shear stress, which can be used in a one-dimensional column urban model. We found that the intrinsic spatial average, in which the volume or area of the solid parts are not included in the average process, yield greater time-spatial average of total stress within the canopy and a more evident abrupt change at the top of the buildings than the comprehensive spatial average, in which the volume or area of the solid parts are included in the average.

The impact of different aperture distribution models and critical stress criteria on equivalent permeability in fractured rocks

NASA Astrophysics Data System (ADS)

Bisdom, Kevin; Bertotti, Giovanni; Nick, Hamidreza M.

2016-05-01

Predicting equivalent permeability in fractured reservoirs requires an understanding of the fracture network geometry and apertures. There are different methods for defining aperture, based on outcrop observations (power law scaling), fundamental mechanics (sublinear length-aperture scaling), and experiments (Barton-Bandis conductive shearing). Each method predicts heterogeneous apertures, even along single fractures (i.e., intrafracture variations), but most fractured reservoir models imply constant apertures for single fractures. We compare the relative differences in aperture and permeability predicted by three aperture methods, where permeability is modeled in explicit fracture networks with coupled fracture-matrix flow. Aperture varies along single fractures, and geomechanical relations are used to identify which fractures are critically stressed. The aperture models are applied to real-world large-scale fracture networks. (Sub)linear length scaling predicts the largest average aperture and equivalent permeability. Barton-Bandis aperture is smaller, predicting on average a sixfold increase compared to matrix permeability. Application of critical stress criteria results in a decrease in the fraction of open fractures. For the applied stress conditions, Coulomb predicts that 50% of the network is critically stressed, compared to 80% for Barton-Bandis peak shear. The impact of the fracture network on equivalent permeability depends on the matrix hydraulic properties, as in a low-permeable matrix, intrafracture connectivity, i.e., the opening along a single fracture, controls equivalent permeability, whereas for a more permeable matrix, absolute apertures have a larger impact. Quantification of fracture flow regimes using only the ratio of fracture versus matrix permeability is insufficient, as these regimes also depend on aperture variations within fractures.

Gamification in Stress Management Apps: A Critical App Review

PubMed Central

Christmann, Corinna A; Bleser, Gabriele

2017-01-01

Background In today’s society, stress is more and more often a cause of disease. This makes stress management an important target of behavior change programs. Gamification has been suggested as one way to support health behavior change. However, it remains unclear to which extend available gamification techniques are integrated in stress management apps, and if their occurrence is linked to the use of elements from behavior change theory. Objective The aim of this study was to investigate the use of gamification techniques in stress management apps and the cooccurrence of these techniques with evidence-based stress management methods and behavior change techniques. Methods A total of 62 stress management apps from the Google Play Store were reviewed on their inclusion of 17 gamification techniques, 15 stress management methods, and 26 behavior change techniques. For this purpose, an extended taxonomy of gamification techniques was constructed and applied by 2 trained, independent raters. Results Interrater-reliability was high, with agreement coefficient (AC)=.97. Results show an average of 0.5 gamification techniques for the tested apps and reveal no correlations between the use of gamification techniques and behavior change techniques (r=.17, P=.20), or stress management methods (r=.14, P=.26). Conclusions This leads to the conclusion that designers of stress management apps do not use gamification techniques to influence the user’s behaviors and reactions. Moreover, app designers do not exploit the potential of combining gamification techniques with behavior change theory. PMID:28592397

Estimation of stress distribution in ferromagnetic tensile specimens using low cost eddy current stress measurement system and BP neural network.

PubMed

Li, Jianwei; Zhang, Weimin; Zeng, Weiqin; Chen, Guolong; Qiu, Zhongchao; Cao, Xinyuan; Gao, Xuanyi

2017-01-01

Estimation of the stress distribution in ferromagnetic components is very important for evaluating the working status of mechanical equipment and implementing preventive maintenance. Eddy current testing technology is a promising method in this field because of its advantages of safety, no need of coupling agent, etc. In order to reduce the cost of eddy current stress measurement system, and obtain the stress distribution in ferromagnetic materials without scanning, a low cost eddy current stress measurement system based on Archimedes spiral planar coil was established, and a method based on BP neural network to obtain the stress distribution using the stress of several discrete test points was proposed. To verify the performance of the developed test system and the validity of the proposed method, experiment was implemented using structural steel (Q235) specimens. Standard curves of sensors at each test point were achieved, the calibrated data were used to establish the BP neural network model for approximating the stress variation on the specimen surface, and the stress distribution curve of the specimen was obtained by interpolating with the established model. The results show that there is a good linear relationship between the change of signal modulus and the stress in most elastic range of the specimen, and the established system can detect the change in stress with a theoretical average sensitivity of -0.4228 mV/MPa. The obtained stress distribution curve is well consonant with the theoretical analysis result. At last, possible causes and improving methods of problems appeared in the results were discussed. This research has important significance for reducing the cost of eddy current stress measurement system, and advancing the engineering application of eddy current stress testing.

Estimation of stress distribution in ferromagnetic tensile specimens using low cost eddy current stress measurement system and BP neural network

PubMed Central

Li, Jianwei; Zeng, Weiqin; Chen, Guolong; Qiu, Zhongchao; Cao, Xinyuan; Gao, Xuanyi

2017-01-01

Estimation of the stress distribution in ferromagnetic components is very important for evaluating the working status of mechanical equipment and implementing preventive maintenance. Eddy current testing technology is a promising method in this field because of its advantages of safety, no need of coupling agent, etc. In order to reduce the cost of eddy current stress measurement system, and obtain the stress distribution in ferromagnetic materials without scanning, a low cost eddy current stress measurement system based on Archimedes spiral planar coil was established, and a method based on BP neural network to obtain the stress distribution using the stress of several discrete test points was proposed. To verify the performance of the developed test system and the validity of the proposed method, experiment was implemented using structural steel (Q235) specimens. Standard curves of sensors at each test point were achieved, the calibrated data were used to establish the BP neural network model for approximating the stress variation on the specimen surface, and the stress distribution curve of the specimen was obtained by interpolating with the established model. The results show that there is a good linear relationship between the change of signal modulus and the stress in most elastic range of the specimen, and the established system can detect the change in stress with a theoretical average sensitivity of -0.4228 mV/MPa. The obtained stress distribution curve is well consonant with the theoretical analysis result. At last, possible causes and improving methods of problems appeared in the results were discussed. This research has important significance for reducing the cost of eddy current stress measurement system, and advancing the engineering application of eddy current stress testing. PMID:29145500

Mechanical characterization and modeling of brazed tungsten and Cu-Cr-Zr alloy using stress relief interlayers

NASA Astrophysics Data System (ADS)

Qu, Dandan; Zhou, Zhangjian; Yum, Youngjin; Aktaa, Jarir

2014-12-01

A rapidly solidified foil-type Ti-Zr based amorphous filler with a melting temperature of 850 °C was used to braze tungsten to Cu-Cr-Zr alloy for water cooled divertors and plasma facing components application. Brazed joints of dissimilar materials suffer from a mismatch in coefficients of thermal expansion. In order to release the residual stress caused by the mismatch, brazed joints of tungsten and Cu-Cr-Zr alloy using different interlayers were studied. The shear strength tests of brazed W/Cu joints show that the average strength of the joint with a W70Cu30 composite plate interlayer reached 119.8 MPa, and the average strength of the joint with oxygen free high conductivity copper (OFHC Cu)/Mo multi-interlayers reached 140.8 MPa, while the joint without interlayer was only 16.6 MPa. Finite element method (FEM) has been performed to investigate the stress distribution and effect of stress relief interlayers. FEM results show that the maximum von Mises stress occurs in the tungsten/filler interface and that the filler suffers the peak residual stresses and becomes the weakest zone. And the use of OFHC Cu/Mo multi-interlayers can reduce the residual stress significantly, which agrees with the mechanical experiment data.

Modeling for stress-strain curve of a porous NiTi under compressive loading

NASA Astrophysics Data System (ADS)

Zhao, Ying; Taya, Minoru

2005-05-01

Two models for predicting the stress-strain curve of porous NiTi under compressive loading are presented in this paper. Porous NiTi shape memory alloy is investigated as a composite composed of solid NiTi as matrix and pores as inclusions. Eshelby"s equivalent inclusion method and Mori-Tanaka"s mean-field theory are employed in both models. In the first model, the geometry of the pores is assumed as sphere. The composite is with close-cells. While in the second model, two geometries of the pores, sphere and ellipsoid, are investigated. The pores are interconnected to each other forming an open-cell microstructure. The two adjacent pores connected along equator ring are investigated as a unit. Two pores interact with each other as they are connected. The average eigenstrain of each unit is obtained by taking the average of each pore"s eigenstrain. The stress-strain curves of porous shape memory alloy with spherical pores and ellipsoidal pores are compared, it is found that the shape of the pores has a nonignorable influence on the mechanical property of the porous NiTi. Comparison of the stress-strain curves of the two models shows that introducing of the average eigenstrains in the second model makes the predictions more agreeable to the experimental results.

Bi-ventricular finite element model of right ventricle overload in the healthy rat heart.

PubMed

Masithulela, Fulufhelo

2016-11-25

The recognition of RV overpressure is critical to human life, as this may signify morbidity and mortality. Right ventricle (RV) dysfunction is understood to have an impact on the performance of the left ventricle (LV), but the mechanisms remain poorly understood. It is understood that ventricular compliance has the ability to affect cardiac performance. In this study, a bi-ventricular model of the rat heart was used in preference to other, single-ventricle models. Finite element analysis (FEA) of the bi-ventricular model provides important information on the function of the healthy heart. The passive myocardium was modelled as a nearly incompressible, hyperelastic, transversely isotropic material using finite element (FE) methods. Bi-ventricular geometries of healthy rat hearts reconstructed from magnetic resonance images were imported in Abaqus©. In simulating the normal passive filling of the rat heart, pressures of 4.8 kPa and 0.0098 kPa were applied to the inner walls of the LV and RV respectively. In addition, to simulate the overpressure of the RV, pressures of 2.4 kPa and 4.8 kPa were applied to the endocardial walls of the LV and RV respectively. As boundary conditions, the circumferential and longitudinal displacements at the base were set to zero. The radial displacements at the base were left free. The results show that the average circumferential stress at the mid-wall in the overloaded model increased from 2.8 kPa to 18.2 kPa. The average longitudinal stress increased from 1.5 kPa to 9.7 kPa. Additionally, in the radial direction, the average stress increased from 0.1 kPa to 0.6 kPa in the mid-wall. The average circumferential strain was found to be 0.138 and 0.100 on the endocardium of the over pressured and healthy model respectively. The average circumferential stress at the epicardium, mid-wall and endocardium in the case of a normal heart is 10 times lower than in the overloaded heart model. The finite analysis method is able to provide insights into the behaviour of the over pressured model (myocardium). In the overloaded model the high stresses and strains were observed on the septal wall. The bi-ventricular model was shown to provide useful information relating to the over pressured ventricle. The possible heart dysfunction may be attributable to high stress and strain in the over pressured heart.

Therapeutic touch and post-Hurricane Hugo stress.

PubMed

Olson, M; Sneed, N; Bonadonna, R; Ratliff, J; Dias, J

1992-06-01

This repeated-session design sought to answer questions about the effectiveness of therapeutic touch in reduction of stress for 23 individuals following a natural disaster. In addition, methodological issues related to the average length of time for a therapeutic-touch treatment and a method of documenting the nonverbal interaction between subject and toucher were investigated. Findings indicate that stressed people report themselves to be less stressed following therapeutic touch (p = .05). Time of therapeutic-touch intervention varied significantly between the touchers, with a range of 6.8 to 20 minutes. Qualitative data examining the interaction of toucher and subject raised a number of questions that require further study.

Impact of hybrid delivery of education on student academic performance and the student experience.

PubMed

Congdon, Heather Brennan; Nutter, Douglas A; Charneski, Lisa; Butko, Peter

2009-11-12

To compare student academic performance and the student experience in the first-year doctor of pharmacy (PharmD) program between the main and newly opened satellite campuses of the University of Maryland. Student performance indicators including graded assessments, course averages, cumulative first-year grade point average (GPA), and introductory pharmacy practice experience (IPPE) evaluations were analyzed retrospectively. Student experience indicators were obtained via an online survey instrument and included involvement in student organizations; time-budgeting practices; and stress levels and their perceived effect on performance. Graded assessments, course averages, GPA, and IPPE evaluations were indistinguishable between campuses. Students' time allocation was not different between campuses, except for time spent attending class and watching lecture videos. There was no difference between students' stress levels at each campus. The implementation of a satellite campus to expand pharmacy education yielded academic performance and student engagement comparable to those from traditional delivery methods.

Residual Stresses in SAVY 4000 and Hagan Container Bodies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stroud, Mary Ann; Hill, Mary Ann; Tokash, Justin Charles

Chloride-induced stress corrosion cracking (SCC) has been investigated as a potential failure mechanism for the SAVY 4000 and the Hagan containers used to store plutonium-bearing materials at Los Alamos National Laboratory. This report discusses the regions of the container bodies most susceptible to SCC and the magnitude of the residual stresses in those regions. Boiling MgCl2 testing indicated that for both containers the region near the top weld was most susceptible to SCC. The Hagan showed through wall cracking after 22-24 hours of exposure both parallel (axial stresses) and perpendicular (hoop stresses) to the weld. The SAVY 4000 container showedmore » significant cracking above and below the weld after 47 hours of exposure but there was no visual evidence of a through wall crack and the cracks did not leak water. Two through wall holes formed in the bottom of the SAVY 4000 container after 44-46 hours of exposure. For both containers, average “through wall” residual stresses were determined from hole drilling data 4 mm below the weld. In the Hagan body, average tensile hoop stresses were 194 MPa and average compressive axial stresses were -120 MPa. In the SAVY 4000 body, average compressive hoop stresses were 11 MPa and average tensile axial stresses were 25 MPa. Results suggest that because the Hagan container exhibited through wall cracking in a shorter time in boiling MgCl2 and had the higher average tensile stress, 194 MPa hoop stress, it is more susceptible to SCC than the SAVY 4000 container.« less

Monitoring eruption activity using temporal stress changes at Mount Ontake volcano.

PubMed

Terakawa, Toshiko; Kato, Aitaro; Yamanaka, Yoshiko; Maeda, Yuta; Horikawa, Shinichiro; Matsuhiro, Kenjiro; Okuda, Takashi

2016-02-19

Volcanic activity is often accompanied by many small earthquakes. Earthquake focal mechanisms represent the fault orientation and slip direction, which are influenced by the stress field. Focal mechanisms of volcano-tectonic earthquakes provide information on the state of volcanoes via stresses. Here we demonstrate that quantitative evaluation of temporal stress changes beneath Mt. Ontake, Japan, using the misfit angles of focal mechanism solutions to the regional stress field, is effective for eruption monitoring. The moving average of misfit angles indicates that during the precursory period the local stress field beneath Mt. Ontake was deviated from the regional stress field, presumably by stress perturbations caused by the inflation of magmatic/hydrothermal fluids, which was removed immediately after the expulsion of volcanic ejecta. The deviation of the local stress field can be an indicator of increases in volcanic activity. The proposed method may contribute to the mitigation of volcanic hazards.

Monitoring eruption activity using temporal stress changes at Mount Ontake volcano

PubMed Central

Terakawa, Toshiko; Kato, Aitaro; Yamanaka, Yoshiko; Maeda, Yuta; Horikawa, Shinichiro; Matsuhiro, Kenjiro; Okuda, Takashi

2016-01-01

Volcanic activity is often accompanied by many small earthquakes. Earthquake focal mechanisms represent the fault orientation and slip direction, which are influenced by the stress field. Focal mechanisms of volcano-tectonic earthquakes provide information on the state of volcanoes via stresses. Here we demonstrate that quantitative evaluation of temporal stress changes beneath Mt. Ontake, Japan, using the misfit angles of focal mechanism solutions to the regional stress field, is effective for eruption monitoring. The moving average of misfit angles indicates that during the precursory period the local stress field beneath Mt. Ontake was deviated from the regional stress field, presumably by stress perturbations caused by the inflation of magmatic/hydrothermal fluids, which was removed immediately after the expulsion of volcanic ejecta. The deviation of the local stress field can be an indicator of increases in volcanic activity. The proposed method may contribute to the mitigation of volcanic hazards. PMID:26892716

Modeling the effects of high-G stress on pilots in a tracking task

NASA Technical Reports Server (NTRS)

Korn, J.; Kleinman, D. L.

1978-01-01

Air-to-air tracking experiments were conducted at the Aerospace Medical Research Laboratories using both fixed and moving base dynamic environment simulators. The obtained data, which includes longitudinal error of a simulated air-to-air tracking task as well as other auxiliary variables, was analyzed using an ensemble averaging method. In conjunction with these experiments, the optimal control model is applied to model a human operator under high-G stress.

Local yield stress statistics in model amorphous solids

NASA Astrophysics Data System (ADS)

Barbot, Armand; Lerbinger, Matthias; Hernandez-Garcia, Anier; García-García, Reinaldo; Falk, Michael L.; Vandembroucq, Damien; Patinet, Sylvain

2018-03-01

We develop and extend a method presented by Patinet, Vandembroucq, and Falk [Phys. Rev. Lett. 117, 045501 (2016), 10.1103/PhysRevLett.117.045501] to compute the local yield stresses at the atomic scale in model two-dimensional Lennard-Jones glasses produced via differing quench protocols. This technique allows us to sample the plastic rearrangements in a nonperturbative manner for different loading directions on a well-controlled length scale. Plastic activity upon shearing correlates strongly with the locations of low yield stresses in the quenched states. This correlation is higher in more structurally relaxed systems. The distribution of local yield stresses is also shown to strongly depend on the quench protocol: the more relaxed the glass, the higher the local plastic thresholds. Analysis of the magnitude of local plastic relaxations reveals that stress drops follow exponential distributions, justifying the hypothesis of an average characteristic amplitude often conjectured in mesoscopic or continuum models. The amplitude of the local plastic rearrangements increases on average with the yield stress, regardless of the system preparation. The local yield stress varies with the shear orientation tested and strongly correlates with the plastic rearrangement locations when the system is sheared correspondingly. It is thus argued that plastic rearrangements are the consequence of shear transformation zones encoded in the glass structure that possess weak slip planes along different orientations. Finally, we justify the length scale employed in this work and extract the yield threshold statistics as a function of the size of the probing zones. This method makes it possible to derive physically grounded models of plasticity for amorphous materials by directly revealing the relevant details of the shear transformation zones that mediate this process.

Tensile stress-strain behavior of graphite/epoxy laminates

NASA Technical Reports Server (NTRS)

Garber, D. P.

1982-01-01

The tensile stress-strain behavior of a variety of graphite/epoxy laminates was examined. Longitudinal and transverse specimens from eleven different layups were monotonically loaded in tension to failure. Ultimate strength, ultimate strain, and strss-strain curves wee obtained from four replicate tests in each case. Polynominal equations were fitted by the method of least squares to the stress-strain data to determine average curves. Values of Young's modulus and Poisson's ratio, derived from polynomial coefficients, were compared with laminate analysis results. While the polynomials appeared to accurately fit the stress-strain data in most cases, the use of polynomial coefficients to calculate elastic moduli appeared to be of questionable value in cases involving sharp changes in the slope of the stress-strain data or extensive scatter.

Spatially explicit estimation of heat stress-related impacts of climate change on the milk production of dairy cows in the United Kingdom.

PubMed

Fodor, Nándor; Foskolos, Andreas; Topp, Cairistiona F E; Moorby, Jon M; Pásztor, László; Foyer, Christine H

2018-01-01

Dairy farming is one the most important sectors of United Kingdom (UK) agriculture. It faces major challenges due to climate change, which will have direct impacts on dairy cows as a result of heat stress. In the absence of adaptations, this could potentially lead to considerable milk loss. Using an 11-member climate projection ensemble, as well as an ensemble of 18 milk loss estimation methods, temporal changes in milk production of UK dairy cows were estimated for the 21st century at a 25 km resolution in a spatially-explicit way. While increases in UK temperatures are projected to lead to relatively low average annual milk losses, even for southern UK regions (<180 kg/cow), the 'hottest' 25×25 km grid cell in the hottest year in the 2090s, showed an annual milk loss exceeding 1300 kg/cow. This figure represents approximately 17% of the potential milk production of today's average cow. Despite the potential considerable inter-annual variability of annual milk loss, as well as the large differences between the climate projections, the variety of calculation methods is likely to introduce even greater uncertainty into milk loss estimations. To address this issue, a novel, more biologically-appropriate mechanism of estimating milk loss is proposed that provides more realistic future projections. We conclude that South West England is the region most vulnerable to climate change economically, because it is characterised by a high dairy herd density and therefore potentially high heat stress-related milk loss. In the absence of mitigation measures, estimated heat stress-related annual income loss for this region by the end of this century may reach £13.4M in average years and £33.8M in extreme years.

Prediction of the Creep-Fatigue Lifetime of Alloy 617: An Application of Non-destructive Evaluation and Information Integration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vivek Agarwal; Richard Wright; Timothy Roney

A relatively simple method using the nominal constant average stress information and the creep rupture model is developed to predict the creep-fatigue lifetime of Alloy 617, in terms of time to rupture. The nominal constant average stress is computed using the stress relaxation curve. The predicted time to rupture can be converted to number of cycles to failure using the strain range, the strain rate during each cycle, and the hold time information. The predicted creep-fatigue lifetime is validated against the experimental measurements of the creep-fatigue lifetime collected using conventional laboratory creep-fatigue tests. High temperature creep-fatigue tests of Alloy 617more » were conducted in air at 950°C with a tensile hold period of up to 1800s in a cycle at total strain ranges of 0.3% and 0.6%. It was observed that the proposed method is conservative in that the predicted lifetime is less than the experimentally determined values. The approach would be relevant to calculate the remaining useful life to a component like a steam generator that might fail by the creep-fatigue mechanism.« less

On computing stress in polymer systems involving multi-body potentials from molecular dynamics simulation

NASA Astrophysics Data System (ADS)

Fu, Yao; Song, Jeong-Hoon

2014-08-01

Hardy stress definition has been restricted to pair potentials and embedded-atom method potentials due to the basic assumptions in the derivation of a symmetric microscopic stress tensor. Force decomposition required in the Hardy stress expression becomes obscure for multi-body potentials. In this work, we demonstrate the invariance of the Hardy stress expression for a polymer system modeled with multi-body interatomic potentials including up to four atoms interaction, by applying central force decomposition of the atomic force. The balance of momentum has been demonstrated to be valid theoretically and tested under various numerical simulation conditions. The validity of momentum conservation justifies the extension of Hardy stress expression to multi-body potential systems. Computed Hardy stress has been observed to converge to the virial stress of the system with increasing spatial averaging volume. This work provides a feasible and reliable linkage between the atomistic and continuum scales for multi-body potential systems.

Stress interactions among arrays of tensile cracks in 3D: Implications for the nucleation of shear failure and the orientations of faults.

NASA Astrophysics Data System (ADS)

Healy, D.; Davis, T.

2017-12-01

In low porosity rocks it is widely believed that planes of shear failure nucleate through the interaction of arrays of smaller tensile microcracks. This model has been confirmed through laboratory rock deformation experiments and detailed microstructural analyses. In this contribution we use the Boundary Element Method (BEM) to model the interactions of arrays of tensile cracks, discretised as ellipsoidal voids in three dimensions (3D). We calculate the elastic stresses in the solid matrix surrounding the cracks resulting from an applied load and include the interaction effects of each crack upon all the others. We explore the role of variations in crack shape, size, position and orientation upon the total and locally perturbed stress fields. We calculate the average crack normal stress (CNS) acting over the area of each tensile crack, and then find the locus of the maximum value of this stress throughout the modelled volume. Following Reches & Lockner (1994) and Healy et al. (2006a, 2006b), we assert that planes of shear failure will most likely nucleate on surfaces parallel to the locus of maximum average CNS. These shear planes are oblique to all three principal stresses in the far field.

In vitro simulator with numerical stress analysis for evaluation of stent-assisted coiling embolization in cerebral aneurysm treatments.

PubMed

Shi, Chaoyang; Kojima, Masahiro; Tercero, Carlos; Najdovski, Zoran; Ikeda, Seiichi; Fukuda, Toshio; Arai, Fumihito; Negoro, Makoto

2014-12-01

There are several complications associated with Stent-assisted Coil Embolization (SACE) in cerebral aneurysm treatments, due to damaging operations by surgeons and undesirable mechanical properties of stents. Therefore, it is necessary to develop an in vitro simulator that provides both training and research for evaluating the mechanical properties of stents. A new in vitro simulator for three-dimensional digital subtraction angiography was constructed, followed by aneurysm models fabricated with new materials. Next, this platform was used to provide training and to conduct photoelastic stress analysis to evaluate the SACE technique. The average interaction stress increasingly varied for the two different stents. Improvements for the Maximum-Likelihood Expectation-Maximization method were developed to reconstruct cross-sections with both thickness and stress information. The technique presented can improve a surgeon's skills and quantify the performance of stents to improve mechanical design and classification. This method can contribute to three-dimensional stress and volume variation evaluation and assess a surgeon's skills. Copyright © 2013 John Wiley & Sons, Ltd.

Subgrid or Reynolds stress-modeling for three-dimensional turbulence computations

NASA Technical Reports Server (NTRS)

Rubesin, M. W.

1975-01-01

A review is given of recent advances in two distinct computational methods for evaluating turbulence fields, namely, statistical Reynolds stress modeling and turbulence simulation, where large eddies are followed in time. It is shown that evaluation of the mean Reynolds stresses, rather than use of a scalar eddy viscosity, permits an explanation of streamline curvature effects found in several experiments. Turbulence simulation, with a new volume averaging technique and third-order accurate finite-difference computing is shown to predict the decay of isotropic turbulence in incompressible flow with rather modest computer storage requirements, even at Reynolds numbers of aerodynamic interest.

Mental and Physical Workload, Salivary Stress Biomarkers and Taste Perception: Mars Desert Research Station Expedition

PubMed Central

Rai, Balwant; Kaur, Jasdeep

2012-01-01

Background: Very few studies have been conducted on the effects of simulation of Mars conditions on taste. Aims: This study was planned to find the effects of physical and mental workload on taste sensitivity and salivary stress biomarkers. Materials and Methods: Twelve crew members were selected. Taste reactions and intensity of the taste sensations to quinine sulfate, citric acid, and sucrose were tested before and after mental and physical tasks for one hour. Also, psychological mood states by profile of mood state, salivary, salivary alpha amylase and cortisol, and current stress test scores were measured before and after mental and physical tasks. Results: Average time intensity evaluation showed that after the mental and physical tasks, the perceived duration of bitter, sour, and sweet taste sensations was significantly shortened relative to control group. There were good correlations between average time intensity of sweetness, bitterness, sourness and cortisol levels. Conclusions: Taste alterations due to stress can have an effect on the health and confidence of astronauts in long- term space missions. Thus, this issue remains one of the important issues for future human explorations. PMID:23181230

Stress Testing After Percutaneous Coronary Intervention in the Veterans Affairs HealthCare System: Insights from the Veterans Affairs Clinical Assessment, Reporting, and Tracking Program.

PubMed

Bradley, Steven M; Hess, Edward; Winchester, David E; Sussman, Jeremy B; Aggarwal, Vikas; Maddox, Thomas M; Barón, Anna E; Rumsfeld, John S; Ho, P Michael

2015-09-01

Stress testing after percutaneous coronary intervention (PCI) in fee-for-service settings is common and rates vary by hospital. Rates of stress testing after PCI within integrated healthcare systems, such as the Veterans Affairs (VA) are unknown. We evaluated all VA patients who underwent PCI from October 2007 through June 2010. To avoid the influence of Medicare eligibility on rates of stress testing use in the VA, we excluded Medicare eligible patients during the follow-up period. Hospital-level variation in risk-standardized rates of stress testing and the association with 1-year mortality and myocardial infarction was determined from Markov chain Monte Carlo methods. Among 10 293 patients undergoing PCI at 55 VA hospitals, 2239 (21.8%) had a stress test performed within 1 year of PCI and 3902 (37.9%) within 2 years. Most stress tests after PCI were performed with nuclear imaging (79.8%). The hospital-level risk-standardized rate of stress testing differed significantly from the average at 14 hospitals, with 8 (14.5%) hospitals significantly below and 6 (10.9%) hospitals significantly above the average stress testing rate. Hospital-level risk-standardized stress testing rates were not significantly correlated with risk-standardized mortality (Spearman ρ=-0.24; P=0.08) or myocardial infarction rates (Spearman ρ=0.20; P=0.14). In the VA, nearly 40% of patients underwent stress testing in the 2 years after PCI, which is a third less than published studies from other healthcare systems. However, stress testing rates varied across VA hospitals, suggesting opportunities to optimize the use of stress testing are still present in integrated healthcare systems. © 2015 American Heart Association, Inc.

Chronic stress and sexual function in women.

PubMed

Hamilton, Lisa Dawn; Meston, Cindy M

2013-10-01

Chronic stress is known to have negative effects on reproduction, but little is known about how it affects the sexual response cycle. The present study examined the relationship between chronic stress and sexual arousal and the mechanisms that mediate this relationship. The aim of this study is to test the relationship between chronic stress and sexual arousal and identify mechanisms that may explain this relationship. We predicted that women experiencing high levels of chronic stress would show lower levels of genital arousal and dehydroepiandrosterone (DHEAS) and higher levels of cortisol and cognitive distraction compared with women with average levels of stress. Women who were categorized as high in chronic stress (high stress group; n=15) or average in chronic stress (average stress group; n=15) provided saliva samples and watched an erotic film while having their genital and psychological arousal measured. Main outcome measures were vaginal pulse amplitude, psychological arousal, salivary cortisol, salivary DHEAS, and heart rate and compared them between women with high and average levels of chronic stress. Women in the high stress group had lower levels of genital, but not psychological arousal, had higher levels of cortisol, and reported more distraction during the erotic film than women in the average stress group. The main predictor of decreased genital sexual arousal was participants' distraction scores. High levels of chronic stress were related to lower levels of genital sexual arousal. Both psychological (distraction) and hormonal (increased cortisol) factors were related to the lower levels of sexual arousal seen in women high in chronic stress, but distraction was the only significant predictor when controlling for other variables. © 2013 International Society for Sexual Medicine.

Dislocation-induced stress in polycrystalline materials: mesoscopic simulations in the dislocation density formalism

NASA Astrophysics Data System (ADS)

Berkov, D. V.; Gorn, N. L.

2018-06-01

In this paper we present a simple and effective numerical method which allows a fast Fourier transformation-based evaluation of stress generated by dislocations with arbitrary directions and Burgers vectors if the (site-dependent) dislocation density is known. Our method allows the evaluation of the dislocation stress using a rectangular grid with shape-anisotropic discretization cells without employing higher multipole moments of the dislocation interaction coefficients. Using the proposed method, we first simulate the stress created by relatively simple non-homogeneous distributions of vertical edge and so-called ‘mixed’ dislocations in a disk-shaped sample, which is necessary to understand the dislocation behavior in more complicated systems. The main part of our research is devoted to the stress distribution in polycrystalline layers with the dislocation density rapidly varying with the distance to the layer bottom. Considering GaN as a typical example of such systems, we investigate dislocation-induced stress for edge and mixed dislocations, having random orientations of Burgers vectors among crystal grains. We show that the rapid decay of the dislocation density leads to many highly non-trivial features of the stress distributions in such layers and study in detail the dependence of these features on the average grain size. Finally we develop an analytical approach which allows us to predict the evolution of the stress variance with the grain size and compare analytical predictions with numerical results.

Exercise mitigates cumulative associations between stress and BMI in girls age 10–19

PubMed Central

Prather, Aric A.; Epel, Elissa S.; Loharuka, Sheila; Adler, Nancy E.; Laraia, Barbara

2015-01-01

Objective Long-term psychological stress is associated with BMI increases in children as they transition to adulthood, while long-term maintenance of physical activity can slow excess weight gain. We hypothesized that in addition to these main effects, long-term physical activity mitigates the relationship between long-term stress and BMI increase. Methods The NHLBI Growth and Health Study enrolled 2,379 10-year-old Black and White girls, following them annually for 10 measurement points. Growth curve modeling captured the dynamics of BMI, measured yearly, and stress and physical activity, measured every other year. Results At average levels of activity and stress, with all covariates remaining fixed, average BMI at baseline was 19.74 (SE = 0.38) and increased 0.64 BMI (SE= 0.01, p < .001) units every year. However, this increase in BMI significantly varied as a function of cumulative stress and physical activity. Slower BMI gain occurred in those girls who were less stressed and more active (0.62 BMI units/year, SE= .02, p < .001), whereas the most rapid and largest growth occurred in girls who were the more stressed and less active (0.92 BMI units/year, SE= .02, p < .001). Racial identification did not alter these effects. Conclusions As hypothesized, in girls who maintained long-term activity, BMI growth was mitigated, even when reporting high long-term stress, compared to less physically active girls. This study adds to a converging literature in which physical activity, a modifiable prevention target, functions to potentially limit the damaging health effects of long-term psychological stress. PMID:26301595

The Impact of Laughter Yoga on the Stress of Cancer Patients before Chemotherapy

PubMed Central

Farifteh, Shadi; Mohammadi-Aria, Alireza; Kiamanesh, Alireza; Mofid, Bahram

2014-01-01

Background Cancer is usually accompanied by considerable stress for the sufferer, and the stress has destructive effects on Chemotherapy treatment process. Therefore, the current research deals with the effect of yoga laughter on the cancer patients’ stress before chemotherapy. Methods In this research, as the first step, 37 cancer sufferers , who had been hospitalized in Shohada Tajrish Hospital (Behnam Daneshpoor Charity Organization) and had the requirements necessary for being taken as research samples, were selected for data collection. The mentioned patients were classified randomly in experimental and control groups. Collected data were analyzed by the multi-variable covariance analysis test. Results The results show there is a meaningful difference in the stress average before and after interference in the test group (p<0.05). Conclusion Laughter yoga can decrease the stress in cancer sufferers before chemotherapy. PMID:25628838

Fatigue Moderates the Relationship Between Perceived Stress and Suicidal Ideation: Evidence From Two High-Resolution Studies.

PubMed

Kleiman, Evan M; Turner, Brianna J; Chapman, Alexander L; Nock, Matthew K

2018-01-01

Theoretical models of self-harm suggest that high perceived stress and high fatigue (which might affect the ability to cope with stress) may interact to predict the short-term occurrence of suicidal ideation and nonsuicidal self-injury (NSSI). We tested 3 approaches to examining this interaction, each of which provided a different understanding of the specific nature of these associations: comparing each individual's daily stress/fatigue to the entire sample's overall average (i.e., grand-mean centering), comparing each individual's daily perceived stress/fatigue to his or her overall average (i.e., group- or participant-mean centering), and comparing each individual's average perceived stress/fatigue to the sample's overall average (i.e., centering participant means on overall grand mean). In 2 studies, adolescents (n = 30; 574 daily reports, M age = 17.3 years, range = 12-19; 87.6% female) and young adults (n = 60; 698 daily reports; M age = 23.25 years, range = 18-35; 85% female) completed daily measures of perceived stress, fatigue, suicidal ideation, and NSSI. In both samples, the interaction between high daily perceived stress and high daily fatigue predicted greater odds of daily suicidal ideation (but not NSSI). Only the model comparing each individual's daily stress/fatigue to the entire sample's overall average was consistently significant across the two studies. Participants were most likely to experience suicidal ideation on days when both perceived stress and fatigue were elevated relative to the average level experienced across people and time points. Studies should build upon these findings with more in-depth examination of the temporal nature of stability and change in these factors as they relate to sustained suicidal ideation.

Inertia and Couple-Stress Effects in a Curvilinear Thrust Hydrostatic Bearing

NASA Astrophysics Data System (ADS)

Walicka, A.; Jurczak, P.; Falicki, J.

2017-08-01

The flow of a couple-stress lubricant in a clearance of a curvilinear thrust hydrostatic bearing with impermeable walls is considered. The flow in the bearing clearance is considered with inertia forces. The equations of motion are solved by an averaged inertia method. As a result, the formulae for pressure distributions without and with inertia effects were obtained. Radial thrust bearings and spherical bearings are discussed as numerical examples. It is shown that inertia effects influence the bearing performance considerably.

A synchrotron X-ray diffraction deconvolution method for the measurement of residual stress in thermal barrier coatings as a function of depth.

PubMed

Li, C; Jacques, S D M; Chen, Y; Daisenberger, D; Xiao, P; Markocsan, N; Nylen, P; Cernik, R J

2016-12-01

The average residual stress distribution as a function of depth in an air plasma-sprayed yttria stabilized zirconia top coat used in thermal barrier coating (TBC) systems was measured using synchrotron radiation X-ray diffraction in reflection geometry on station I15 at Diamond Light Source, UK, employing a series of incidence angles. The stress values were calculated from data deconvoluted from diffraction patterns collected at increasing depths. The stress was found to be compressive through the thickness of the TBC and a fluctuation in the trend of the stress profile was indicated in some samples. Typically this fluctuation was observed to increase from the surface to the middle of the coating, decrease a little and then increase again towards the interface. The stress at the interface region was observed to be around 300 MPa, which agrees well with the reported values. The trend of the observed residual stress was found to be related to the crack distribution in the samples, in particular a large crack propagating from the middle of the coating. The method shows promise for the development of a nondestructive test for as-manufactured samples.

The effect of temperature on the average volume of Barkhausen jump on Q235 carbon steel

NASA Astrophysics Data System (ADS)

Guo, Lei; Shu, Di; Yin, Liang; Chen, Juan; Qi, Xin

2016-06-01

On the basis of the average volume of Barkhausen jump (AVBJ) vbar generated by irreversible displacement of magnetic domain wall under the effect of the incentive magnetic field on ferromagnetic materials, the functional relationship between saturation magnetization Ms and temperature T is employed in this paper to deduce the explicit mathematical expression among AVBJ vbar, stress σ, incentive magnetic field H and temperature T. Then the change law between AVBJ vbar and temperature T is researched according to the mathematical expression. Moreover, the tensile and compressive stress experiments are carried out on Q235 carbon steel specimens at different temperature to verify our theories. This paper offers a series of theoretical bases to solve the temperature compensation problem of Barkhausen testing method.

Assessment of the Local Residual Stresses of 7050-T7452 Aluminum Alloy in Microzones by the Instrumented Indentation with the Berkovich Indenter

NASA Astrophysics Data System (ADS)

He, M.; Huang, C. H.; Wang, X. X.; Yang, F.; Zhang, N.; Li, F. G.

2017-10-01

The local residual stresses in microzones are investigated by the instrumented indentation method with the Berkovich indenter. The parameters required for determination of residual stresses are obtained from indentation load-penetration depth curves constructed during instrumented indentation tests on flat square 7050-T7452 aluminum alloy specimens with a central hole containing the compressive residual stresses generated by the cold extrusion process. The force balance system with account of the tensile and compressive residual stresses is used to explain the phenomenon of different contact areas produced by the same indentation load. The effect of strain-hardening exponent on the residual stress is tuned-off by application of the representative stress σ_{0.033} in the average contact pressure assessment using the Π theorem, while the yield stress value is obtained from the constitutive function. Finally, the residual stresses are calculated according to the proposed equations of the force balance system, and their feasibility is corroborated by the XRD measurements.

Effects of hydrodynamic conditions on the sorption behaviors of aniline on sediment with coexistence of nitrobenzene.

PubMed

Wang, Peng; Hua, Zulin; Cai, Yunjie; Shen, Xia; Li, Qiongqiong; Liu, Xiaoyuan

2015-08-01

The sorption behaviors of pollutants affected by hydrodynamic conditions were confirmed in natural water environment. The effects of hydrodynamic conditions on the sorption behaviors of aniline on sediment with coexistence of nitrobenzene were investigated. The particle entrainment simulator (PES) was used to simulate varied bottom shear stresses. The batch equilibrium method was applied to the experiments with the stress levels and the action time controlled at 0.2-0.5 N/m(2) and 24 h, respectively. The findings indicated that apparent partition coefficient of aniline on sediment increased with the shear stress significantly, while decreased with nitrobenzene concentration. On the contrary, both the sorption amount of aniline on suspended particulate matter (Q s) and the effect of nitrobenzene concentration on Q s declined as the shear stress increased. The sorption kinetic results showed that the sorption process followed the pseudo-second-order kinetics equation, and the process included two stages: fast sorption stage and slow sorption stage, among which the average sorption rate of fast stage was 7.5-9.5 times that of slow one. The effect of shear stress on the average sorption rate of aniline was enhanced with the increase of nitrobenzene concentration. And shear stress weakened the disturbance of cosolute on main solute sorption process. In addition, experiment results of sorption kinetic show that only the initial sorption rate was affected by shear stress and cosolute concentration. In the first 5 min, shear stress had positive effects on the sorption rate. After that, the sorption rate barely changed with shear stress and cosolute concentration.

Method for making nanomaterials

DOEpatents

Fan, Hongyou; Wu, Huimeng

2013-06-04

A method of making a nanostructure by preparing a face centered cubic-ordered metal nanoparticle film from metal nanoparticles, such as gold and silver nanoparticles, exerting a hydrostatic pressure upon the film at pressures of several gigapascals, followed by applying a non-hydrostatic stress perpendicularly at a pressure greater than approximately 10 GPA to form an array of nanowires with individual nanowires having a relatively uniform length, average diameter and density.

Directly Estimating Earthquake Rupture Area using Second Moments to Reduce the Uncertainty in Stress Drop

NASA Astrophysics Data System (ADS)

McGuire, Jeffrey J.; Kaneko, Yoshihiro

2018-06-01

The key kinematic earthquake source parameters: rupture velocity, duration and area, shed light on earthquake dynamics, provide direct constraints on stress-drop, and have implications for seismic hazard. However, for moderate and small earthquakes, these parameters are usually poorly constrained due to limitations of the standard analysis methods. Numerical experiments by Kaneko and Shearer [2014,2015] demonstrated that standard spectral fitting techniques can lead to roughly 1 order of magnitude variation in stress-drop estimates that do not reflect the actual rupture properties even for simple crack models. We utilize these models to explore an alternative approach where we estimate the rupture area directly. For the suite of models, the area averaged static stress drop is nearly constant for models with the same underlying friction law, yet corner frequency based stress-drop estimates vary by a factor of 5-10 even for noise free data. Alternatively, we simulated inversions for the rupture area as parameterized by the second moments of the slip distribution. A natural estimate for the rupture area derived from the second moments is A=πLcWc, where Lc and Wc are the characteristic rupture length and width. This definition yields estimates of stress drop that vary by only 10% between the models but are slightly larger than the true area-averaged values. We simulate inversions for the second moments for the various models and find that the area can be estimated well when there are at least 15 available measurements of apparent duration at a variety of take-off angles. The improvement compared to azimuthally-averaged corner-frequency based approaches results from the second moments accounting for directivity and removing the assumption of a circular rupture area, both of which bias the standard approach. We also develop a new method that determines the minimum and maximum values of rupture area that are consistent with a particular dataset at the 95% confidence level. For the Kaneko and Shearer models with 20+ randomly distributed observations and ˜10% noise levels, we find that the maximum and minimum bounds on rupture area typically vary by a factor of two and that the minimum stress drop is often more tightly constrained than the maximum.

Mediation of the Relationship between Maternal Phthalate Exposure and Preterm Birth by Oxidative Stress with Repeated Measurements across Pregnancy.

PubMed

Ferguson, Kelly K; Chen, Yin-Hsiu; VanderWeele, Tyler J; McElrath, Thomas F; Meeker, John D; Mukherjee, Bhramar

2017-03-01

Mediation analysis is useful for understanding mechanisms and has been used minimally in the study of the environment and disease. We examined mediation of the association between phthalate exposure during pregnancy and preterm birth by oxidative stress. This nested case-control study of preterm birth ( n = 130 cases, 352 controls) included women who delivered in Boston, Massachusestts, from 2006 through 2008. Phthalate metabolites and 8-isoprostane, an oxidative stress biomarker, were measured in urine from three visits in pregnancy. We applied four counterfactual mediation methods: method 1, utilizing exposure and mediator averages; method 2, using averages but allowing for an exposure-mediator interaction; method 3, incorporating longitudinal measurements of the exposure and mediator; and method 4, using longitudinal measurements and allowing for an exposure-mediator interaction. We observed mediation of the associations between phthalate metabolites and all preterm birth by 8-isoprostane, with the greatest estimated proportion mediated observed for spontaneous preterm births specifically. Fully utilizing repeated measures of the exposure and mediator improved precision of indirect (i.e., mediated) effect estimates, and including an exposure-mediator interaction increased the estimated proportion mediated. For example, for mono(2-ethyl-carboxy-propyl) phthalate (MECPP), a metabolite of di(2-ethylhexyl) phthalate (DEHP), the percent of the total effect mediated by 8-isoprostane increased from 47% to 60% with inclusion of an exposure-mediator interaction term, in reference to a total adjusted odds ratio of 1.67 or 1.48, respectively. This demonstrates mediation of the phthalate-preterm birth relationship by oxidative stress, and the utility of complex regression models in capturing mediated associations when repeated measures of exposure and mediator are available and an exposure-mediator interaction may exist. Citation: Ferguson KK, Chen YH, VanderWeele TJ, McElrath TF, Meeker JD, Mukherjee B. 2017. Mediation of the relationship between maternal phthalate exposure and preterm birth by oxidative stress with repeated measurements across pregnancy. Environ Health Perspect 125:488-494; http://dx.doi.org/10.1289/EHP282.

Analysis of crack propagation in roller bearings using the boundary integral equation method - A mixed-mode loading problem

NASA Technical Reports Server (NTRS)

Ghosn, L. J.

1988-01-01

Crack propagation in a rotating inner raceway of a high-speed roller bearing is analyzed using the boundary integral method. The model consists of an edge plate under plane strain condition upon which varying Hertzian stress fields are superimposed. A multidomain boundary integral equation using quadratic elements was written to determine the stress intensity factors KI and KII at the crack tip for various roller positions. The multidomain formulation allows the two faces of the crack to be modeled in two different subregions, making it possible to analyze crack closure when the roller is positioned on or close to the crack line. KI and KII stress intensity factors along any direction were computed. These calculations permit determination of crack growth direction along which the average KI times the alternating KI is maximum.

Gamification in Stress Management Apps: A Critical App Review.

PubMed

Hoffmann, Alexandra; Christmann, Corinna A; Bleser, Gabriele

2017-06-07

In today's society, stress is more and more often a cause of disease. This makes stress management an important target of behavior change programs. Gamification has been suggested as one way to support health behavior change. However, it remains unclear to which extend available gamification techniques are integrated in stress management apps, and if their occurrence is linked to the use of elements from behavior change theory. The aim of this study was to investigate the use of gamification techniques in stress management apps and the cooccurrence of these techniques with evidence-based stress management methods and behavior change techniques. A total of 62 stress management apps from the Google Play Store were reviewed on their inclusion of 17 gamification techniques, 15 stress management methods, and 26 behavior change techniques. For this purpose, an extended taxonomy of gamification techniques was constructed and applied by 2 trained, independent raters. Interrater-reliability was high, with agreement coefficient (AC)=.97. Results show an average of 0.5 gamification techniques for the tested apps and reveal no correlations between the use of gamification techniques and behavior change techniques (r=.17, P=.20), or stress management methods (r=.14, P=.26). This leads to the conclusion that designers of stress management apps do not use gamification techniques to influence the user's behaviors and reactions. Moreover, app designers do not exploit the potential of combining gamification techniques with behavior change theory. ©Alexandra Hoffmann, Corinna A Christmann, Gabriele Bleser. Originally published in JMIR Serious Games (http://games.jmir.org), 07.06.2017.

Grain size effect on Lcr elastic wave for surface stress measurement of carbon steel

NASA Astrophysics Data System (ADS)

Liu, Bin; Miao, Wenbing; Dong, Shiyun; He, Peng

2018-04-01

Based on critical refraction longitudinal wave (Lcr wave) acoustoelastic theory, correction method for grain size effect on surface stress measurement was discussed in this paper. Two fixed distance Lcr wave transducers were used to collect Lcr wave, and difference in time of flight between Lcr waves was calculated with cross-correlation coefficient function, at last relationship of Lcr wave acoustoelastic coefficient and grain size was obtained. Results show that as grain size increases, propagation velocity of Lcr wave decreases, one cycle is optimal step length for calculating difference in time of flight between Lcr wave. When stress value is within stress turning point, relationship of difference in time of flight between Lcr wave and stress is basically consistent with Lcr wave acoustoelastic theory, while there is a deviation and it is higher gradually as stress increasing. Inhomogeneous elastic plastic deformation because of inhomogeneous microstructure and average value of surface stress in a fixed distance measured with Lcr wave were considered as the two main reasons for above results. As grain size increasing, Lcr wave acoustoelastic coefficient decreases in the form of power function, then correction method for grain size effect on surface stress measurement was proposed. Finally, theoretical discussion was verified by fracture morphology observation.

The Inclusion of In-Plane Stresses in Delamination Criteria

NASA Technical Reports Server (NTRS)

Fenske, Matthew T.

1999-01-01

A study of delamination failure was conducted with emphasis on delamination criteria. Evidence is presented which supports the inclusion of the in-plane stresses in addition to the interlaminar stress terms in delamination criteria. The delamination is characterized as the failure of a resin rich region in between ply sets. The entire six component stress state in this resin layer is calculated through a finite element analysis, averaged over a dimension of 1.75 ply thicknesses, and used in a Modified von Mises Delamination Criterion. This criterion builds onto previous criteria by including all six stress components in the interply resin layer. The MVMDC shows good correlation to experimental data. The results show that the treatment of delamination as the failure of a finite interply resin layer is a valid method and that the MVMDC, considering the full stress state, accurately indicates delamination for different laminate families.

On computing stress in polymer systems involving multi-body potentials from molecular dynamics simulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fu, Yao, E-mail: fu5@mailbox.sc.edu, E-mail: jhsong@cec.sc.edu; Song, Jeong-Hoon, E-mail: fu5@mailbox.sc.edu, E-mail: jhsong@cec.sc.edu

2014-08-07

Hardy stress definition has been restricted to pair potentials and embedded-atom method potentials due to the basic assumptions in the derivation of a symmetric microscopic stress tensor. Force decomposition required in the Hardy stress expression becomes obscure for multi-body potentials. In this work, we demonstrate the invariance of the Hardy stress expression for a polymer system modeled with multi-body interatomic potentials including up to four atoms interaction, by applying central force decomposition of the atomic force. The balance of momentum has been demonstrated to be valid theoretically and tested under various numerical simulation conditions. The validity of momentum conservation justifiesmore » the extension of Hardy stress expression to multi-body potential systems. Computed Hardy stress has been observed to converge to the virial stress of the system with increasing spatial averaging volume. This work provides a feasible and reliable linkage between the atomistic and continuum scales for multi-body potential systems.« less

Finite element modelling versus classic beam theory: comparing methods for stress estimation in a morphologically diverse sample of vertebrate long bones

PubMed Central

Brassey, Charlotte A.; Margetts, Lee; Kitchener, Andrew C.; Withers, Philip J.; Manning, Phillip L.; Sellers, William I.

2013-01-01

Classic beam theory is frequently used in biomechanics to model the stress behaviour of vertebrate long bones, particularly when creating intraspecific scaling models. Although methodologically straightforward, classic beam theory requires complex irregular bones to be approximated as slender beams, and the errors associated with simplifying complex organic structures to such an extent are unknown. Alternative approaches, such as finite element analysis (FEA), while much more time-consuming to perform, require no such assumptions. This study compares the results obtained using classic beam theory with those from FEA to quantify the beam theory errors and to provide recommendations about when a full FEA is essential for reasonable biomechanical predictions. High-resolution computed tomographic scans of eight vertebrate long bones were used to calculate diaphyseal stress owing to various loading regimes. Under compression, FEA values of minimum principal stress (σmin) were on average 142 per cent (±28% s.e.) larger than those predicted by beam theory, with deviation between the two models correlated to shaft curvature (two-tailed p = 0.03, r2 = 0.56). Under bending, FEA values of maximum principal stress (σmax) and beam theory values differed on average by 12 per cent (±4% s.e.), with deviation between the models significantly correlated to cross-sectional asymmetry at midshaft (two-tailed p = 0.02, r2 = 0.62). In torsion, assuming maximum stress values occurred at the location of minimum cortical thickness brought beam theory and FEA values closest in line, and in this case FEA values of τtorsion were on average 14 per cent (±5% s.e.) higher than beam theory. Therefore, FEA is the preferred modelling solution when estimates of absolute diaphyseal stress are required, although values calculated by beam theory for bending may be acceptable in some situations. PMID:23173199

ZnO thin film piezoelectric micromachined microphone with symmetric composite vibrating diaphragm

NASA Astrophysics Data System (ADS)

Li, Junhong; Wang, Chenghao; Ren, Wei; Ma, Jun

2017-05-01

Residual stress is an important factor affecting the sensitivity of piezoelectric micromachined microphone. A symmetric composite vibrating diaphragm was adopted in the micro electro mechanical systems piezoelectric microphone to decrease the residual stress and improve the sensitivity of microphone in this paper. The ZnO film was selected as piezoelectric materials of microphone for its higher piezoelectric coefficient d 31 and lower relative dielectric constant. The thickness optimization of piezoelectric film on square diaphragm is difficult to be fulfilled by analytic method. To optimize the thickness of ZnO films, the stress distribution in ZnO film was analyzed by finite element method and the average stress in different thickness of ZnO films was given. The ZnO films deposited using dc magnetron sputtering exhibits a densely packed structure with columnar crystallites preferentially oriented along (002) plane. The diaphragm of microphone fabricated by micromachining techniques is flat and no wrinkling at corners, and the sensitivity of microphone is higher than 1 mV Pa-1. These results indicate the diaphragm has lower residual stress.

Professional burnout, stress and job satisfaction of nursing staff at a university hospital1

PubMed Central

Portero de la Cruz, Silvia; Vaquero Abellán, Manuel

2015-01-01

OBJECTIVES: to describe the social and work characteristics of the nursing staff at a tertiary hospital in the Public Health Service of Andalucía, to assess the degree of professional professional burnout and job satisfaction of those professionals and to study the possible relation between the professional burnout variables and the stress and job satisfaction levels on the one hand and social and employment variables on the other. METHOD: descriptive and cross-sectional study in a sample of 258 baccalaureate and auxiliary nurses. As research instruments, an original and specific questionnaire was used to collect social and employment variables, the Maslach Burnout Inventory, the Nursing Stress Scale and the Font-Roja questionnaire. Descriptive, inferential statistics and multivariate analysis were applied. RESULTS: average scores were found for professional stress and satisfaction, corresponding to 44,23 and 65,46 points, respectively. As regards professional burnout, an average score was found on the emotional exhaustion subscale; a high score for depersonalization and a low score for professional accomplishment. Studies are needed to identify the scores on these subscales in health organizations and to produce knowledge on their interrelations. PMID:26155012

Dietary taurine intake, nutrients intake, dietary habits and life stress by depression in Korean female college students: a case-control study.

PubMed

Park, Ji-Yeon; You, Jeong-Soon; Chang, Kyung-Ja

2010-08-24

The purpose of this study was to investigate the dietary taurine intake, nutrients intake, dietary habits and life stress by depression in Korean female college students. In this study, research data were collected in March 2009 and 65 patients with depression and 65 controls without depression participated. The CES-D (Center for Epidemiologic Studies Depression) scale was used for depression measure and controls were matched for age. A 3-day recall method was used for dietary assessment (2 weekdays and 1 weekend day). Average height, weight and body mass index (BMI) were 161.3+/-0.5 cm, 55.3+/-1.0 kg and 21.2+/-0.4 kg/m2 for depression patients and those of control group were 161.4+/-0.7 cm, 53.1+/-0.8 kg and 20.3+/-0.2 kg/m2, respectively. Average dietary taurine intakes of depression patients and control group were 89.1 and 88.0 mg/day, respectively. There was no significant difference in dietary taurine intake between depression patients and control group. The average intakes of vitamin A (p<0.05), beta-carotene (p<0.01), vitamin C (p<0.05), folic acid (p<0.05) and fiber (p<0.05) of depression patients were significantly lower compared to control group. The average total dietary habit score of depression patients (47.2) was significantly lower than that of control group (51.3) (p<0.01). The average dietary habit scores of "eating meals at regular times" (p<0.05), "eating adequate amount of meals" (p<0.05), "having meals with diverse foods" (p<0.05), "avoiding eating spicy foods" (p<0.01) and "eating protein foods such as meat, fish, eggs, beans more than 2 times a day" (p<0.05) were significantly lower in depression patients compare to control group. The average scores of total life stress (p<0.001) and all stress categories of depression patients were significantly higher than those of control group except faculty problem score. These results show that depression patients have poor dietary habits and unbalanced nutrition status. Also depression patients have higher life stress score.Therefore, continuous nutrition education and counselling for good dietary habits and balanced nutrition status are needed to prevent depression in Korean college students.

Thinning increases climatic resilience of red pine

USGS Publications Warehouse

Magruder, Matthew; Chhin, Sophan; Palik, Brian; Bradford, John B.

2013-01-01

Forest management techniques such as intermediate stand-tending practices (e.g., thinning) can promote climatic resiliency in forest stands by moderating tree competition. Residual trees gain increased access to environmental resources (i.e., soil moisture, light), which in turn has the potential to buffer trees from stressful climatic conditions. The influences of climate (temperature and precipitation) and forest management (thinning method and intensity) on the productivity of red pine (Pinus resinosa Ait.) in Michigan were examined to assess whether repeated thinning treatments were able to increase climatic resiliency (i.e., maintaining productivity and reduced sensitivity to climatic stress). The cumulative productivity of each thinning treatment was determined, and it was found that thinning from below to a residual basal area of 14 m2·ha−1 produced the largest average tree size but also the second lowest overall biomass per acre. On the other hand, the uncut control and the thinning from above to a residual basal area of 28 m2·ha−1 produced the smallest average tree size but also the greatest overall biomass per acre. Dendrochronological methods were used to quantify sensitivity of annual radial growth to monthly and seasonal climatic factors for each thinning treatment type. Climatic sensitivity was influenced by thinning method (i.e., thinning from below decreased sensitivity to climatic stress more than thinning from above) and by thinning intensity (i.e., more intense thinning led to a lower climatic sensitivity). Overall, thinning from below to a residual basal area of 21 m2·ha−1 represented a potentially beneficial compromise to maximize tree size, biomass per acre, and reduced sensitivity to climatic stress, and, thus, the highest level of climatic resilience.

3,4-Methylenedioxymethamphetamine (MDMA) abuse may cause oxidative stress and potential free radical damage.

PubMed

Zhou, Jun F; Chen, Peng; Zhou, Ye H; Zhang, Liang; Chen, Huai H

2003-05-01

To investigate whether 3,4-methylenedioxymethamphetamine abuse (MDMA abuse) may cause oxidative stress and potential free radical damage in the bodies of MDMA abusers (MA), and to explore the mechanisms by which MDMA abuse may be causing oxidative stress. One hundred and twenty MA and 120 healthy volunteers (HV) were enrolled in a random control study design, in which the level of lipoperoxide (LPO) in erythrocytes, and the levels of Vitamin C (VC), Vitamin E (VE) and beta-carotene (beta-CAR) in plasma as well as the activities of superoxide dismutase (SOD) and catalase (CAT) in erythrocytes were determined by spectrophotometric methods. Compared with the average values of the above biochemical parameters in the HV group, the average value of LPO in erythrocytes in the MA group was significantly increased (P < 0.0001), while the average values of VC, VE and beta-CAR in plasma as well as those of SOD and CAT in erythrocytes in the MA group were significantly decreased (P < 0.0001). The analysis of bivariate correlations suggested that with the increase of the MDMA abuse dose and the MDMA abuse duration, the level of LPO in erythrocytes in the MA was increased (P < 0.0001), while the levels of VC, VE and beta-CAR in plasma as well as the activities of SOD and CAT in erythrocytes in the MA were decreased (P < 0.0001). The findings in this study suggest that MDMA abuse may cause oxidative stress and potential free radical damage to MA.

Mass Function of Galaxy Clusters in Relativistic Inhomogeneous Cosmology

NASA Astrophysics Data System (ADS)

Ostrowski, Jan J.; Buchert, Thomas; Roukema, Boudewijn F.

The current cosmological model (ΛCDM) with the underlying FLRW metric relies on the assumption of local isotropy, hence homogeneity of the Universe. Difficulties arise when one attempts to justify this model as an average description of the Universe from first principles of general relativity, since in general, the Einstein tensor built from the averaged metric is not equal to the averaged stress-energy tensor. In this context, the discrepancy between these quantities is called "cosmological backreaction" and has been the subject of scientific debate among cosmologists and relativists for more than 20 years. Here we present one of the methods to tackle this problem, i.e. averaging the scalar parts of the Einstein equations, together with its application, the cosmological mass function of galaxy clusters.

Myocardial perfusion quantification using simultaneously acquired 13 NH3 -ammonia PET and dynamic contrast-enhanced MRI in patients at rest and stress.

PubMed

Kunze, Karl P; Nekolla, Stephan G; Rischpler, Christoph; Zhang, Shelley HuaLei; Hayes, Carmel; Langwieser, Nicolas; Ibrahim, Tareq; Laugwitz, Karl-Ludwig; Schwaiger, Markus

2018-04-19

Systematic differences with respect to myocardial perfusion quantification exist between DCE-MRI and PET. Using the potential of integrated PET/MRI, this study was conceived to compare perfusion quantification on the basis of simultaneously acquired 13 NH 3 -ammonia PET and DCE-MRI data in patients at rest and stress. Twenty-nine patients were examined on a 3T PET/MRI scanner. DCE-MRI was implemented in dual-sequence design and additional T 1 mapping for signal normalization. Four different deconvolution methods including a modified version of the Fermi technique were compared against 13 NH 3 -ammonia results. Cohort-average flow comparison yielded higher resting flows for DCE-MRI than for PET and, therefore, significantly lower DCE-MRI perfusion ratios under the common assumption of equal arterial and tissue hematocrit. Absolute flow values were strongly correlated in both slice-average (R 2  = 0.82) and regional (R 2  = 0.7) evaluations. Different DCE-MRI deconvolution methods yielded similar flow result with exception of an unconstrained Fermi method exhibiting outliers at high flows when compared with PET. Thresholds for Ischemia classification may not be directly tradable between PET and MRI flow values. Differences in perfusion ratios between PET and DCE-MRI may be lifted by using stress/rest-specific hematocrit conversion. Proper physiological constraints are advised in model-constrained deconvolution. © 2018 International Society for Magnetic Resonance in Medicine.

Noninvasive evaluation of mental stress using by a refined rough set technique based on biomedical signals.

PubMed

Liu, Tung-Kuan; Chen, Yeh-Peng; Hou, Zone-Yuan; Wang, Chao-Chih; Chou, Jyh-Horng

2014-06-01

Evaluating and treating of stress can substantially benefits to people with health problems. Currently, mental stress evaluated using medical questionnaires. However, the accuracy of this evaluation method is questionable because of variations caused by factors such as cultural differences and individual subjectivity. Measuring of biomedical signals is an effective method for estimating mental stress that enables this problem to be overcome. However, the relationship between the levels of mental stress and biomedical signals remain poorly understood. A refined rough set algorithm is proposed to determine the relationship between mental stress and biomedical signals, this algorithm combines rough set theory with a hybrid Taguchi-genetic algorithm, called RS-HTGA. Two parameters were used for evaluating the performance of the proposed RS-HTGA method. A dataset obtained from a practice clinic comprising 362 cases (196 male, 166 female) was adopted to evaluate the performance of the proposed approach. The empirical results indicate that the proposed method can achieve acceptable accuracy in medical practice. Furthermore, the proposed method was successfully used to identify the relationship between mental stress levels and bio-medical signals. In addition, the comparison between the RS-HTGA and a support vector machine (SVM) method indicated that both methods yield good results. The total averages for sensitivity, specificity, and precision were greater than 96%, the results indicated that both algorithms produced highly accurate results, but a substantial difference in discrimination existed among people with Phase 0 stress. The SVM algorithm shows 89% and the RS-HTGA shows 96%. Therefore, the RS-HTGA is superior to the SVM algorithm. The kappa test results for both algorithms were greater than 0.936, indicating high accuracy and consistency. The area under receiver operating characteristic curve for both the RS-HTGA and a SVM method were greater than 0.77, indicating a good discrimination capability. In this study, crucial attributes in stress evaluation were successfully recognized using biomedical signals, thereby enabling the conservation of medical resources and elucidating the mapping relationship between levels of mental stress and candidate attributes. In addition, we developed a prototype system for mental stress evaluation that can be used to provide benefits in medical practice. Copyright © 2014. Published by Elsevier B.V.

BIMOS transistor solutions for ESD protection in FD-SOI UTBB CMOS technology

NASA Astrophysics Data System (ADS)

Galy, Philippe; Athanasiou, S.; Cristoloveanu, S.

2016-01-01

We evaluate the Electro-Static Discharge (ESD) protection capability of BIpolar MOS (BIMOS) transistors integrated in ultrathin silicon film for 28 nm Fully Depleted SOI (FD-SOI) Ultra Thin Body and BOX (UTBB) high-k metal gate technology. Using as a reference our measurements in hybrid bulk-SOI structures, we extend the BIMOS design towards the ultrathin silicon film. Detailed study and pragmatic evaluations are done based on 3D TCAD simulation with standard physical models using Average Current Slope (ACS) method and quasi-static DC stress (Average Voltage Slope AVS method). These preliminary 3D TACD results are very encouraging in terms of ESD protection efficiency in advanced FD-SOI CMOS.

Spatially explicit estimation of heat stress-related impacts of climate change on the milk production of dairy cows in the United Kingdom

PubMed Central

Topp, Cairistiona F. E.; Moorby, Jon M.; Pásztor, László; Foyer, Christine H.

2018-01-01

Dairy farming is one the most important sectors of United Kingdom (UK) agriculture. It faces major challenges due to climate change, which will have direct impacts on dairy cows as a result of heat stress. In the absence of adaptations, this could potentially lead to considerable milk loss. Using an 11-member climate projection ensemble, as well as an ensemble of 18 milk loss estimation methods, temporal changes in milk production of UK dairy cows were estimated for the 21st century at a 25 km resolution in a spatially-explicit way. While increases in UK temperatures are projected to lead to relatively low average annual milk losses, even for southern UK regions (<180 kg/cow), the ‘hottest’ 25×25 km grid cell in the hottest year in the 2090s, showed an annual milk loss exceeding 1300 kg/cow. This figure represents approximately 17% of the potential milk production of today’s average cow. Despite the potential considerable inter-annual variability of annual milk loss, as well as the large differences between the climate projections, the variety of calculation methods is likely to introduce even greater uncertainty into milk loss estimations. To address this issue, a novel, more biologically-appropriate mechanism of estimating milk loss is proposed that provides more realistic future projections. We conclude that South West England is the region most vulnerable to climate change economically, because it is characterised by a high dairy herd density and therefore potentially high heat stress-related milk loss. In the absence of mitigation measures, estimated heat stress-related annual income loss for this region by the end of this century may reach £13.4M in average years and £33.8M in extreme years. PMID:29738581

A study of job stress and burnout and related factors in the hospital personnel of Iran

PubMed Central

Abarghouei, Mohammad Reza; Sorbi, Mohammad Hossein; Abarghouei, Mehdi; Bidaki, Reza; Yazdanpoor, Shirin

2016-01-01

Introduction Job stress has become one of the main factors in reducing efficiency and the loss of human resources that may cause physical and psychological adverse effects in employees. Hospital personnel are facing different stressful events, such as birth, pain and death, in a single day. Hence, identifying the job stress rates and related factors may be effective in offering proper strategies. Therefore, the present research was done to study the rate of job stress and burnout in hospital personnel and compare some of the related factors in hospitals personnel of Yazd, Iran. Methods This cross-sectional study was conducted on 306 hospital personnel (Male: 114, Female: 192) in Yazd in 2015–16. The data were collected using a demographic questionnaire, Maslach Burnout Inventory (MBI), and Hospital Stress (HSS-35). SPSS-16 software and Pearson-product moment correlation and independent-samples t-test were used for data analysis. Results The mean job stress score was above average. The mean burnout dimensions that were above average included emotional exhaustion (21.7 ± 7.27), depersonalization (9.61 ± 3.74) and personal accomplishment (26.80 ± 6.17). While Pearson correlation revealed a significant positive relationship between job stress, emotional exhaustion, and depersonalization, there was a negative relationship between job stress and personal accomplishment (p < 0.01). Independent-samples t-test results showed that the rate of job stress, emotional exhaustion, and depersonalization in males is higher than females, married people have more emotional exhaustion than single ones, and, finally, health staff have more job stress than administrative staff. At the same time, the administrative staff and females have better personal accomplishment than other groups (p < 0.05). Conclusion Since the rate of job stress in hospital personnel is worrying and it has adverse effects on personnel health, effective strategies on physical and mental health, such as employment support and stress management training, seem crucial to enhance physical and psychological health of hospital personnel. PMID:27648189

Application of Deep Learning and Supervised Learning Methods to Recognize Nonlinear Hidden Pattern in Water Stress Levels from Spatiotemporal Datasets across Rural and Urban US Counties

NASA Astrophysics Data System (ADS)

Eisenhart, T.; Josset, L.; Rising, J. A.; Devineni, N.; Lall, U.

2017-12-01

In the wake of recent water crises, the need to understand and predict the risk of water stress in urban and rural areas has grown. This understanding has the potential to improve decision making in public resource management, policy making, risk management and investment decisions. Assuming an underlying relationship between urban and rural water stress and observable features, we apply Deep Learning and Supervised Learning models to uncover hidden nonlinear patterns from spatiotemporal datasets. Results of interest includes prediction accuracy on extreme categories (i.e. urban areas highly prone to water stress) and not solely the average risk for urban or rural area, which adds complexity to the tuning of model parameters. We first label urban water stressed counties using annual water quality violations and compile a comprehensive spatiotemporal dataset that captures the yearly evolution of climatic, demographic and economic factors of more than 3,000 US counties over the 1980-2010 period. As county-level data reporting is not done on a yearly basis, we test multiple imputation methods to get around the issue of missing data. Using Python libraries, TensorFlow and scikit-learn, we apply and compare the ability of, amongst other methods, Recurrent Neural Networks (testing both LSTM and GRU cells), Convolutional Neural Networks and Support Vector Machines to predict urban water stress. We evaluate the performance of those models over multiple time spans and combine methods to diminish the risk of overfitting and increase prediction power on test sets. This methodology seeks to identify hidden nonlinear patterns to assess the predominant data features that influence urban and rural water stress. Results from this application at the national scale will assess the performance of deep learning models to predict water stress risk areas across all US counties and will highlight a predominant Machine Learning method for modeling water stress risk using spatiotemporal data.

Method of monitoring crystal growth

DOEpatents

Sachs, Emanual M.

1982-01-01

A system and method are disclosed for monitoring the growth of a crystalline body from a liquid meniscus in a furnace. The system provides an improved human/machine interface so as to reduce operator stress, strain and fatigue while improving the conditions for observation and control of the growing process. The system comprises suitable optics for forming an image of the meniscus and body wherein the image is anamorphic so that the entire meniscus can be viewed with good resolution in both the width and height dimensions. The system also comprises a video display for displaying the anamorphic image. The video display includes means for enhancing the contrast between any two contrasting points in the image. The video display also comprises a signal averager for averaging the intensity of at least one preselected portions of the image. The value of the average intensity, can in turn be utilized to control the growth of the body. The system and method are also capable of observing and monitoring multiple processes.

Evaluation of critical shear stresses for consolidated cohesive sediment depositions by using PIV compared with field measurements

NASA Astrophysics Data System (ADS)

Harb, Gabriele; Haun, Stefan

2013-04-01

Reservoir sedimentation is a common problem today. Due to the reduced flow velocities, turbulences and bed shear stresses the transported sediment load start to settle. These depositions reduce the worldwide average storage capacity in the range of about 1% per year. However, depending on the climate conditions and the geology in the catchment area this value may vary strongly. Therefore sediment management tasks, especially the removal of already accumulated sediments, have to be developed for each reservoir separately. The critical bed shear stress is a key parameter used to evaluate the different management tasks and depend strongly on the grain size distribution of the inflowing sediments. However, depositions which contain fine particles like clay and silt increase the critical bed shear stress due to occurring cohesive forces and the use of the Shield curve for evaluating the critical shear stress is no longer valid. Additional data is required for estimating the valid critical shear stress at the reservoir bed. In this study the critical shear stress was evaluated for cohesive sediment samples, taken from two different reservoirs, in a flume in the laboratory. The sediment samples were placed in an installed double bottom in the research flume and the discharge was increased stepwise until mass erosion took place (determined by visual inspection). A 2D PIV device was used to measure the flow conditions (velocities and turbulences) over the sediment sample. The obtained values were used to calculate the bed shear stress for the specific discharge rate by the gravity method and the Reynolds stress method. The results of both methods showed good agreement in the comparison of the values, what indicates that nearly uniform flow conditions occurred in the flume. The results from this study showed that the behaviour of natural cohesive sediments depend strongly on the natural conditions as a result of physical, chemical and biological processes. In this case especially the effect of the layer structure in the sediment samples was controlling the erosion mechanism. The results of the experiments showed also that the obtained average shear stress was above most of the values found in previous conducted studies, which may be explained by consolidation effects in the reservoirs. Additional conducted vane strength measurements have been carried out in situ. The in the field obtained vane strength values were set in relation to the critical shear stresses derived by the experimental tests from the laboratory and to data from a previous conducted study to develop a new relation function. This function may be used in future studies for a rough estimation of the critical shear stress, based on in situ measured vane strength values.

Measurement of fecal glucocorticoids in parrotfishes to assess stress

USGS Publications Warehouse

Turner, J.W.; Nemeth, R.; Rogers, C.

2003-01-01

Coral reefs are in decline worldwide from a combination of natural and human forces. The environmental compromises faced by coral reef habitats and their associated fishes are potentially stressful, and in this study we examined the potential for assessing stress levels in coral reef fish. We determined the feasibility of using fecal casts from parrotfishes for remote assessment of stress-related hormones (cortisol and corticosterone), and the response of these hormones to the stress of restraint and hypoxia. Measurement of these hormones in fecal extracts by high performance liquid chromatography (HPLC) was validated using mass spectrometry, chemical derivitization, and radioactive tracer methods. In aquarium-adapted parrotfish, baseline levels of cortisol and corticosterone averaged 3.4??1.1 and 14.8??2.8ng/g feces, respectively, across 32 days. During 13 days of periodic stress these hormones, respectively, average 10.8-fold and 3.2-fold greater than baseline, with a return to near baseline during a 23-day follow-up. Testosterone was also measured as a reference hormone which is not part of the stress-response axis. Levels of this hormone were similar across the study. These fecal hormones were also measured in a field study of parrotfish in 10 fringing coral reef areas around the Caribbean Island of St. John, US Virgin Islands. Extracts of remotely collected fecal casts of three parrotfish species revealed no difference in respective average hormone levels among these species. Also, there was no difference in respective hormone levels between aquarium and field environments. However, levels of both cortisol and corticosterone, but not testosterone, were elevated in two of the 10 reef sites surveyed. This study demonstrates that parrotfish fecals can be collected in aquarium and field conditions and that steroid hormones in these fecals can be extracted and reliably measured. The study also demonstrates that cortisol and corticosterone in parrotfish fecals can be used as an indicator of the stress-response which is unlikely to be masked by intrinsic variability in the sample source, environment or methodology. ?? 2003 Elsevier Science (USA). All rights reserved.

Spatially averaged flow over a wavy boundary revisited

USGS Publications Warehouse

McLean, S.R.; Wolfe, S.R.; Nelson, J.M.

1999-01-01

Vertical profiles of streamwise velocity measured over bed forms are commonly used to deduce boundary shear stress for the purpose of estimating sediment transport. These profiles may be derived locally or from some sort of spatial average. Arguments for using the latter procedure are based on the assumption that spatial averaging of the momentum equation effectively removes local accelerations from the problem. Using analogies based on steady, uniform flows, it has been argued that the spatially averaged velocity profiles are approximately logarithmic and can be used to infer values of boundary shear stress. This technique of using logarithmic profiles is investigated using detailed laboratory measurements of flow structure and boundary shear stress over fixed two-dimensional bed forms. Spatial averages over the length of the bed form of mean velocity measurements at constant distances from the mean bed elevation yield vertical profiles that are highly logarithmic even though the effect of the bottom topography is observed throughout the water column. However, logarithmic fits of these averaged profiles do not yield accurate estimates of the measured total boundary shear stress. Copyright 1999 by the American Geophysical Union.

Linking initial microstructure and local response during quasistatic granular compaction

DOE PAGES

Hurley, R. C.; Lind, J.; Pagan, D. C.; ...

2017-07-24

In this study, we performed experiments combining three-dimensional x-ray diffraction and x-ray computed tomography to explore the relationship between microstructure and local force and strain during quasistatic granular compaction. We found that initial void space around a grain and contact coordination number before compaction can be used to predict regions vulnerable to above-average local force and strain at later stages of compaction. We also found correlations between void space around a grain and coordination number, and between grain stress and maximum interparticle force, at all stages of compaction. Finally, we observed grains that fracture to have an above-average initial localmore » void space and a below-average initial coordination number. In conclusion, our findings provide (1) a detailed description of microstructure evolution during quasistatic granular compaction, (2) an approach for identifying regions vulnerable to large values of strain and interparticle force, and (3) methods for identifying regions of a material with large interparticle forces and coordination numbers from measurements of grain stress and local porosity.« less

Accuracy of the Generalized Self-Consistent Method in Modelling the Elastic Behaviour of Periodic Composites

NASA Technical Reports Server (NTRS)

Walker, Kevin P.; Freed, Alan D.; Jordan, Eric H.

1993-01-01

Local stress and strain fields in the unit cell of an infinite, two-dimensional, periodic fibrous lattice have been determined by an integral equation approach. The effect of the fibres is assimilated to an infinite two-dimensional array of fictitious body forces in the matrix constituent phase of the unit cell. By subtracting a volume averaged strain polarization term from the integral equation we effectively embed a finite number of unit cells in a homogenized medium in which the overall stress and strain correspond to the volume averaged stress and strain of the constrained unit cell. This paper demonstrates that the zeroth term in the governing integral equation expansion, which embeds one unit cell in the homogenized medium, corresponds to the generalized self-consistent approximation. By comparing the zeroth term approximation with higher order approximations to the integral equation summation, both the accuracy of the generalized self-consistent composite model and the rate of convergence of the integral summation can be assessed. Two example composites are studied. For a tungsten/copper elastic fibrous composite the generalized self-consistent model is shown to provide accurate, effective, elastic moduli and local field representations. The local elastic transverse stress field within the representative volume element of the generalized self-consistent method is shown to be in error by much larger amounts for a composite with periodically distributed voids, but homogenization leads to a cancelling of errors, and the effective transverse Young's modulus of the voided composite is shown to be in error by only 23% at a void volume fraction of 75%.

In vivo evaluation of needle force and friction stress during insertion at varying insertion speed into the brain.

PubMed

Casanova, Fernando; Carney, Paul R; Sarntinoranont, Malisa

2014-11-30

Convection enhanced delivery (CED) infuses drugs directly into brain tissue. Needle insertion is required and results in tissue damage which can promote flowback along the needle track and improper targeting. The goal of this study was to evaluate friction stress (calculated from needle insertion force) as a measure of tissue contact and damage during needle insertion for varying insertion speeds. Forces and surface dimpling during needle insertion were measured in rat brain in vivo. Needle retraction forces were used to calculate friction stresses. These measures were compared to track damage from a previous study. Differences between brain tissues and soft hydrogels were evaluated for varying insertion speeds: 0.2, 2, and 10mm/s. In brain tissue, average insertion force and surface dimpling increased with increasing insertion speed. Average friction stress along the needle-tissue interface decreased with insertion speed (from 0.58 ± 0.27 to 0.16 ± 0.08 kPa). Friction stress varied between brain regions: cortex (0.227 ± 0.27 kPa), external capsule (0.222 ± 0.19 kPa), and CPu (0.383 ± 0.30 kPa). Hydrogels exhibited opposite trends for dimpling and friction stress with insertion speed. Previously, increasing needle damage with insertion speed has been measured with histological methods. Friction stress appears to decrease with increasing tissue damage and decreasing tissue contact, providing the potential for in vivo and real time evaluation along the needle track. Force derived friction stress decreased with increasing insertion speed and was smaller within white matter regions. Hydrogels exhibited opposite trends to brain tissue. Copyright © 2014 Elsevier B.V. All rights reserved.

Reynolds averaged turbulence modelling using deep neural networks with embedded invariance

DOE PAGES

Ling, Julia; Kurzawski, Andrew; Templeton, Jeremy

2016-10-18

There exists significant demand for improved Reynolds-averaged Navier–Stokes (RANS) turbulence models that are informed by and can represent a richer set of turbulence physics. This paper presents a method of using deep neural networks to learn a model for the Reynolds stress anisotropy tensor from high-fidelity simulation data. A novel neural network architecture is proposed which uses a multiplicative layer with an invariant tensor basis to embed Galilean invariance into the predicted anisotropy tensor. It is demonstrated that this neural network architecture provides improved prediction accuracy compared with a generic neural network architecture that does not embed this invariance property.more » Furthermore, the Reynolds stress anisotropy predictions of this invariant neural network are propagated through to the velocity field for two test cases. For both test cases, significant improvement versus baseline RANS linear eddy viscosity and nonlinear eddy viscosity models is demonstrated.« less

Reynolds averaged turbulence modelling using deep neural networks with embedded invariance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ling, Julia; Kurzawski, Andrew; Templeton, Jeremy

There exists significant demand for improved Reynolds-averaged Navier–Stokes (RANS) turbulence models that are informed by and can represent a richer set of turbulence physics. This paper presents a method of using deep neural networks to learn a model for the Reynolds stress anisotropy tensor from high-fidelity simulation data. A novel neural network architecture is proposed which uses a multiplicative layer with an invariant tensor basis to embed Galilean invariance into the predicted anisotropy tensor. It is demonstrated that this neural network architecture provides improved prediction accuracy compared with a generic neural network architecture that does not embed this invariance property.more » Furthermore, the Reynolds stress anisotropy predictions of this invariant neural network are propagated through to the velocity field for two test cases. For both test cases, significant improvement versus baseline RANS linear eddy viscosity and nonlinear eddy viscosity models is demonstrated.« less

Effet de l'anisotropie élastique cristalline sur la distribution des facteurs de Schmid à la surface des polycristaux

NASA Astrophysics Data System (ADS)

Sauzay, Maxime

2006-06-01

Experimental studies of the plasticity mechanisms of polycrystals are usually based on the Schmid factor distribution supposing crystalline elasticity isotropy. A numerical evaluation of the effect of crystalline elasticity anisotropy on the apparent Schmid factor distribution at the free surface of polycrystals is presented. Cubic elasticity is considered. Order II stresses (averaged on all grains with the same crystallographic orientation) as well as variations between averages computed on grains with the same crystallographic orientation but with different neighbour grains are computed. The Finite Element Method is used. Commonly studied metals presenting an increasing anisotropy degree are considered (aluminium, nickel, austenite, copper). Concerning order II stresses in strongly anisotropic metals, the apparent Schmid factor distribution is drifted towards small Schmid factor values (the maximum Schmid factor is equal to 0.43 instead of 0.5) and the slip activation order between characteristic orientations of the crystallographic standard triangle is modified. The computed square deviations of the stresses averaged on grains with the same crystallographic orientation but with different neighbour grains are a bit higher than the second order ones (inter-orientation scatter). Our numerical evaluations agree quantitatively with several observations and measures of the literature concerning stress and strain distribution in copper and austenite polycrystals submitted to low amplitude loadings. Hopefully, the given apparent Schmid factor distributions could help to better understand the observations of the plasticity mechanisms taking place at the free surface of polycrystals. To cite this article: M. Sauzay, C. R. Mecanique 334 (2006).

Constraining Depositional Slope From Sedimentary Structures in Sandy Braided Streams

NASA Astrophysics Data System (ADS)

Lynds, R. M.; Mohrig, D.; Heller, P. L.

2003-12-01

Determination of paleoslopes in ancient fluvial systems has potentially broad application to quantitatively constraining the history of tectonics and paleoclimate in continental sequences. Our method for calculating paleoslopes for sandy braided streams is based upon a simple physical model that establishes depositional skin-frictional shear stresses from assemblages of sedimentary structures and their associated grain size distributions. The addition of a skin-frictional shear stress, with a geometrically determined form-drag shear stress results in a total boundary shear stress which is directly related to water-surface slope averaged over an appropriate spatial scale. In order to apply this model to ancient fluvial systems, it is necessary to measure the following: coarsest suspended sediment size, finest grain size carried in bed load, flow depth, dune height, and dune length. In the rock record, suspended load and bed load can be accurately assessed by well-preserved suspended load deposits ("low-energy" ripples) and bed load deposits (dune foresets). This model predicts an average slope for the North Loup River near Taylor, Nebraska (modern case study) of 2.7 x 10-3. The measured reach-averaged water surface slope for the same reach of the river is 1.37 x 10-3. We suggest that it is possible to calculate the depositional slope of a sandy fluvial system by a factor of approximately two. Additionally, preliminary application of this model to the Lower Jurassic Kayenta Formation throughout the Colorado Plateau provides a promising and consistent evaluation of paleoslope in an ancient and well-preserved, sandy braided stream deposit.

Lagrangian methods for blood damage estimation in cardiovascular devices--How numerical implementation affects the results.

PubMed

Marom, Gil; Bluestein, Danny

2016-01-01

This paper evaluated the influence of various numerical implementation assumptions on predicting blood damage in cardiovascular devices using Lagrangian methods with Eulerian computational fluid dynamics. The implementation assumptions that were tested included various seeding patterns, stochastic walk model, and simplified trajectory calculations with pathlines. Post processing implementation options that were evaluated included single passage and repeated passages stress accumulation and time averaging. This study demonstrated that the implementation assumptions can significantly affect the resulting stress accumulation, i.e., the blood damage model predictions. Careful considerations should be taken in the use of Lagrangian models. Ultimately, the appropriate assumptions should be considered based the physics of the specific case and sensitivity analysis, similar to the ones presented here, should be employed.

Does Stress Result in You Exercising Less? Or Does Exercising Result in You Being Less Stressed? Or is it Both?

PubMed Central

Burg, Matthew M.; Schwartz, Joseph E.; Kronish, Ian M.; Diaz, Keith M.; Alcantara, Carmela; Duer-Hefele, Joan; Davidson, Karina W.

2017-01-01

Background Psychosocial stress contributes to heart disease in part by adversely affecting maintenance of health behaviors, while exercise can reduce stress. Assessing the bi-directional relationship between stress and exercise has been limited by lack of real-time data, and theoretical and statistical models. This lack may hinder efforts to promote exercise maintenance. Purpose We test the bi-directional relationship between stress and exercise using real-time data for the average person, and the variability – individual differences – in this relationship. Methods A single cohort randomized controlled experiment. Healthy young adults (n=79) who reported only intermittent exercise, completed 12 months of stress monitoring by ecological momentary assessment (at the beginning of, end of, and during the day), and continuous activity monitoring by Fitbit. A random coefficients linear mixed model was used to predict end-of-day stress from the occurrence/non-occurrence of exercise that day; a logistic mixed model was used to predict the occurrence/non-occurrence of exercise from ratings of anticipated stress. Separate regression analyses were also performed for each participant. Sensitivity analysis tested all models, restricted to the first 180 days of observation (prior to randomization). Results We found a significant average inverse (i.e., negative) effect of exercise on stress and of stress on exercise. There was significant between-person variability. Of N=69, exercise was associated with a stress reduction for 15, a stress increase for 2, and no change for the remainder. We also found that an increase in anticipated stress reported the previous night or that morning was associated with a significant 20–22% decrease (OR=0.78–0.80) in the odds of exercising that day. Of N=69, this increase in stress reduced the likelihood of exercise for 17, increased the odds for 1, and had no effect for the remainder. We were unable to identify psychosocial factors that moderate the individual differences in these effects. Conclusions The relationship of stress to exercise can be uni- or bi-directional, and varies from person to person. A precision medicine approach may improve exercise uptake. PMID:28290065

Effects of work-related stress on work ability index among refinery workers

PubMed Central

Habibi, Ehsanollah; Dehghan, Habibollah; Safari, Shahram; Mahaki, Behzad; Hassanzadeh, Akbar

2014-01-01

Introduction: Work-related stress is one of the basic problems in industrial also top 10 work-related health problems and it is increasingly implicated in the development a number of problems such as cardiovascular disease, musculoskeletal diseases, early retirement to employees. On the other hand, early retirement to employees from the workplace has increased on the problems of today's industries. Hereof, improving work ability is one of the most effective ways to enhance the ability and preventing disability and early retirement. The aim of This study is determine the relationship between job stress score and work ability index (WAI) at the refinery workers. Materials and Methods: This is a cross-sectional study in which 171 workers from a refinery in isfahan in 2012 who were working in different occupational groups participated. Based on appropriate assignment sampling, 33 office workers, 69 operational workers, and 69 maintenance workers, respectively, were invited to participate in this study. Two questionnaires including work related-stress and WAI were filled in. Finally, the information was analyzed using the SPSS-20 and statistic tests namely, analysis of covariance Kruskal-Wallis test. Pearson correlation coefficient, ANOVA and t-test. Results: Data analysis revealed that 86% and 14% of participants had moderate and severe stress respectively. Average score of stress and standard deviation was 158.7 ± 17.3 that was in extreme stress range. Average score and standard deviation of WAI questionnaire were 37.18 and 3.86 respectively. That placed in a good range. Pearson correlation coefficient showed that WAI score had significant reversed relationship with a score of stress. Conclusion: According to the results, mean stress score among refinery worker was high and one fator that affect work abiity was high stress, hence training on communication skills and safe working environment in order to decreses stress, enhance the work ability of workers. PMID:24741658

Unmanned aircraft system-derived crop height and normalized difference vegetation index metrics for sorghum yield and aphid stress assessment

NASA Astrophysics Data System (ADS)

Stanton, Carly; Starek, Michael J.; Elliott, Norman; Brewer, Michael; Maeda, Murilo M.; Chu, Tianxing

2017-04-01

A small, fixed-wing unmanned aircraft system (UAS) was used to survey a replicated small plot field experiment designed to estimate sorghum damage caused by an invasive aphid. Plant stress varied among 40 plots through manipulation of aphid densities. Equipped with a consumer-grade near-infrared camera, the UAS was flown on a recurring basis over the growing season. The raw imagery was processed using structure-from-motion to generate normalized difference vegetation index (NDVI) maps of the fields and three-dimensional point clouds. NDVI and plant height metrics were averaged on a per plot basis and evaluated for their ability to identify aphid-induced plant stress. Experimental soil signal filtering was performed on both metrics, and a method filtering low near-infrared values before NDVI calculation was found to be the most effective. UAS NDVI was compared with NDVI from sensors onboard a manned aircraft and a tractor. The correlation results showed dependence on the growth stage. Plot averages of NDVI and canopy height values were compared with per-plot yield at 14% moisture and aphid density. The UAS measures of plant height and NDVI were correlated to plot averages of yield and insect density. Negative correlations between aphid density and NDVI were seen near the end of the season in the most damaged crops.

Measurement of fracture stress for 6000-series extruded aluminum alloy tube using multiaxial tube expansion testing method

NASA Astrophysics Data System (ADS)

Nagai, Keisuke; Kuwabara, Toshihiko; Ilinich, Andrey; Luckey, George

2018-05-01

A servo-controlled tension-internal pressure testing machine with an optical 3D digital image correlation system (DIC) is used to measure the multiaxial deformation behavior of an extruded aluminum alloy tube for a strain range from initial yield to fracture. The outer diameter of the test sample is 50.8 mm and wall thickness 2.8 mm. Nine linear stress paths are applied to the specimens: σɸ (axial true stress component) : σθ (circumferential true stress component) = 1:0, 4:1, 2:1, 4:3, 1:1, 3:4, 1:2, 1:4, and 0:1. The equivalent strain rate is approximately 5 × 10-4 s-1 constant. The forming limit curve (FLC) and forming limit stress curve (FLSC) are also measured. Moreover, the average true stress components inside a localized necking area are determined for each specimen from the thickness strain data for the localized necking area and the geometry of the fracture surface.

Stress Fractures of Tibia Treated with Ilizarov External Fixator.

PubMed

Górski, Radosław; Żarek, Sławomir; Modzelewski, Piotr; Górski, Ryszard; Małdyk, Paweł

2016-08-30

Stress fractures are the result of cyclic loading of the bone, which gradually becomes damaged. Most often they are treated by rest or plaster cast and, in rare cases, by internal fixation. There is little published data on initial reposition followed by stabilization with the Ilizarov apparatus in such fractures. Six patients were treated with an external fixator according to the Ilizarov method for a stress fracture of the tibia between 2007 and 2015. Three patients were initially treated conservatively. Due to increasing tibial deformation, they were qualified for surgical treatment with external stabilization. In the other patients, surgery was the first-line treatment. All patients demonstrated risk factors for a stress fracture. After the surgery, they fully loaded the operated limb. No patient developed malunion, nonunion, infection or venous thrombosis. The average time from the first operation to the removal of the external fixator was 19 weeks. Radiographic and clinical outcomes were satisfactory in all patients. 1. The Ilizarov method allows for successful stabilization of stress fractures of the tibia. 2. It may be a good alternative to internal stabilization, especially in patients with multiple comorbidities which affect bone quality and may impair soft tissue healing.

A comparison of constant-load and constant-deflection stress-corrosion tests on precracked DCB specimens. [Double Cantilever Beam

NASA Technical Reports Server (NTRS)

Dorward, R. C.; Hasse, K. R.

1978-01-01

A comparison is made between measurements of stress-corrosion crack propagation made by a constant-load procedure and by a constant-deflection procedure. Precracked double cantilever beam specimens from 7075 aluminum alloy plate were used. The specimens were oriented in such a way that cracking would begin in the short-transverse plane and would propagate in the rolling direction. The specimens were subjected to a buffered salt-chromate solution and a 3.6% synthetic sea salt solution. The measurements were made optically with a binocular microscope. Stress intensities and crack lengths were calculated and crack velocities were obtained. Velocity was plotted against the average calculated stress intensity. Good agreement between the two methods was found for the salt-chromate solution, although some descrepancies were noted for the artificial sea salt solution.

Coseismic temporal changes of slip direction: the effect of absolute stress on dynamic rupture

USGS Publications Warehouse

Guatteri, Mariagiovanna; Spudich, P.

1998-01-01

We investigate the dynamics of rupture at low-stress level. We show that one main difference between the dynamics of high- and low-stress events is the amount of coseismic temporal rake rotation occurring at given points on the fault. Curved striations on exposed fault surfaces and earthquake dislocation models derived from ground-motion inversion indicate that the slip direction may change with time at a point on the fault during dynamic rupture. We use a 3D boundary integral method to model temporal rake variations during dynamic rupture propagation assuming a slip-weakening friction law and isotropic friction. The points at which the slip rotates most are characterized by an initial shear stress direction substantially different from the average stress direction over the fault plane. We show that for a given value of stress drop, the level of initial shear stress (i.e., the fractional stress drop) determines the amount of rotation in slip direction. We infer that seismic events that show evidence of temporal rake rotations are characterized by a low initial shear-stress level with spatially variable direction on the fault (possibly due to changes in fault surface geometry) and an almost complete stress drop.Our models motivate a new interpretation of curved and cross-cutting striations and put new constraints on their analysis. The initial rake is in general collinear with the initial stress at the hypocentral zone, supporting the assumptions made in stress-tensor inversion from first-motion analysis. At other points on the fault, especially away from the hypocenter, the initial slip rake may not be collinear with the initial shear stress, contradicting a common assumption of structural geology. On the other hand, the later part of slip in our models is systematically more aligned with the average stress direction than the early slip. Our modeling suggests that the length of the straight part of curved striations is usually an upper bound of the slip-weakening distance if this parameter is uniform over the fault plane, and the direction of the late part of slip of curved striations should have more weight in the estimate of initial stress direction.

Effects of thermal cycling parameters on residual stresses in alumina scales of CoNiCrAlY and NiCoCrAlY bond coats

DOE PAGES

Nordhorn, Christian; Mücke, Robert; Unocic, Kinga A.; ...

2014-08-20

In this paper, furnace cycling experiments were performed on free-standing high-velocity oxygen-fuel bond coat samples to investigate the effect of material composition, surface texture, and cycling conditions on the average stresses in the formed oxide scales after cooling. The oxide scale thicknesses were determined by SEM image analyses and information about the stresses were acquired by photo-stimulated luminescence-spectroscopy. Additionally, the scale thickness dependent stress fields were calculated in finite-element analyses including approximation functions for the surface roughness derived on the basis of profilometry data. The evolution of the average residual stress as a function of oxide scale thickness was subjectmore » to stochastic fluctuations predominantly caused by local scale spallations. In comparison to the supplemental modeling results, thermal stresses due to mismatch of thermal expansion coefficients are identified as the main contribution to the residual stresses. Finally, the theoretical results emphasize that analyses of spectroscopic data acquired for average stress investigations of alumina scales rely on detailed information about microstructural features.« less

Aerodynamic surface stress intermittency and conditionally averaged turbulence statistics

NASA Astrophysics Data System (ADS)

Anderson, William; Lanigan, David

2015-11-01

Aeolian erosion is induced by aerodynamic stress imposed by atmospheric winds. Erosion models prescribe that sediment flux, Q, scales with aerodynamic stress raised to exponent, n, where n > 1 . Since stress (in fully rough, inertia-dominated flows) scales with incoming velocity squared, u2, it follows that q ~u2n (where u is some relevant component of the flow). Thus, even small (turbulent) deviations of u from its time-mean may be important for aeolian activity. This rationale is augmented given that surface layer turbulence exhibits maximum Reynolds stresses in the fluid immediately above the landscape. To illustrate the importance of stress intermittency, we have used conditional averaging predicated on stress during large-eddy simulation of atmospheric boundary layer flow over an arid, bare landscape. Conditional averaging provides an ensemble-mean visualization of flow structures responsible for erosion `events'. Preliminary evidence indicates that surface stress peaks are associated with the passage of inclined, high-momentum regions flanked by adjacent low-momentum regions. We characterize geometric attributes of such structures and explore streamwise and vertical vorticity distribution within the conditionally averaged flow field. This work was supported by the National Sci. Foundation, Phys. and Dynamic Meteorology Program (PM: Drs. N. Anderson, C. Lu, and E. Bensman) under Grant # 1500224. Computational resources were provided by the Texas Adv. Comp. Center at the Univ. of Texas.

Average Associations Between Sexual Desire, Testosterone, and Stress in Women and Men Over Time.

PubMed

Raisanen, Jessica C; Chadwick, Sara B; Michalak, Nicholas; van Anders, Sari M

2018-05-29

Sexual desire and testosterone are widely assumed to be directly and positively linked to each other despite the lack of supporting empirical evidence. The literature that does exist is mixed, which may result from a conflation of solitary and dyadic desire, and the exclusion of contextual variables, like stress, known to be relevant. Here, we use the Steroid/Peptide Theory of Social Bonds as a framework for examining how testosterone, solitary and partnered desire, and stress are linked over time. To do so, we collected saliva samples (for testosterone and cortisol) and measured desire as well as other variables via questionnaires over nine monthly sessions in 78 women and 79 men. Linear mixed models showed that testosterone negatively predicted partnered desire in women but not men. Stress moderated associations between testosterone and solitary desire in both women and men, but differently: At lower levels of stress, higher average testosterone corresponded to higher average solitary desire for men, but lower solitary desire on average for women. Similarly, for partnered desire, higher perceived stress predicted lower desire for women, but higher desire for men. We conclude by discussing the ways that these results both counter presumptions about testosterone and desire but fit with the existing literature and theory, and highlight the empirical importance of stress and gender norms.

Three-dimensional finite-element analysis of chevron-notched fracture specimens

NASA Technical Reports Server (NTRS)

Raju, I. S.; Newman, J. C., Jr.

1984-01-01

Stress-intensity factors and load-line displacements were calculated for chevron-notched bar and rod fracture specimens using a three-dimensional finite-element analysis. Both specimens were subjected to simulated wedge loading (either uniform applied displacement or uniform applied load). The chevron-notch sides and crack front were assumed to be straight. Crack-length-to-specimen width ratios (a/w) ranged from 0.4 to 0.7. The width-to-thickness ratio (w/B) was 1.45 or 2. The bar specimens had a height-to-width ratio of 0.435 or 0.5. Finite-element models were composed of singularity elements around the crack front and 8-noded isoparametric elements elsewhere. The models had about 11,000 degrees of freedom. Stress-intensity factors were calculated by using a nodal-force method for distribution along the crack front and by using a compliance method for average values. The stress intensity factors and load-line displacements are presented and compared with experimental solutions from the literature. The stress intensity factors and load-line displacements were about 2.5 and 5 percent lower than the reported experimental values, respectively.

Wall Shear Stress, Wall Pressure and Near Wall Velocity Field Relationships in a Whirling Annular Seal

NASA Technical Reports Server (NTRS)

Morrison, Gerald L.; Winslow, Robert B.; Thames, H. Davis, III

1996-01-01

The mean and phase averaged pressure and wall shear stress distributions were measured on the stator wall of a 50% eccentric annular seal which was whirling in a circular orbit at the same speed as the shaft rotation. The shear stresses were measured using flush mounted hot-film probes. Four different operating conditions were considered consisting of Reynolds numbers of 12,000 and 24,000 and Taylor numbers of 3,300 and 6,600. At each of the operating conditions the axial distribution (from Z/L = -0.2 to 1.2) of the mean pressure, shear stress magnitude, and shear stress direction on the stator wall were measured. Also measured were the phase averaged pressure and shear stress. These data were combined to calculate the force distributions along the seal length. Integration of the force distributions result in the net forces and moments generated by the pressure and shear stresses. The flow field inside the seal operating at a Reynolds number of 24,000 and a Taylor number of 6,600 has been measured using a 3-D laser Doppler anemometer system. Phase averaged wall pressure and wall shear stress are presented along with phase averaged mean velocity and turbulence kinetic energy distributions located 0.16c from the stator wall where c is the seal clearance. The relationships between the velocity, turbulence, wall pressure and wall shear stress are very complex and do not follow simple bulk flow predictions.

A Methodology to Detect Abnormal Relative Wall Shear Stress on the Full Surface of the Thoracic Aorta Using 4D Flow MRI

PubMed Central

van Ooij, Pim; Potters, Wouter V.; Nederveen, Aart J.; Allen, Bradley D.; Collins, Jeremy; Carr, James; Malaisrie, S. Chris; Markl, Michael; Barker, Alex J.

2014-01-01

Purpose To compute cohort-averaged wall shear stress (WSS) maps in the thoracic aorta of patients with aortic dilatation or valvular stenosis and to detect abnormal regional WSS. Methods Systolic WSS vectors, estimated from 4D flow MRI data, were calculated along the thoracic aorta lumen in 10 controls, 10 patients with dilated aortas and 10 patients with aortic valve stenosis. 3D segmentations of each aorta were co-registered by group and used to create a cohort-specific aortic geometry. The WSS vectors of each subject were interpolated onto the corresponding cohort-specific geometry to create cohort-averaged WSS maps. A Wilcoxon rank sum test was used to generate aortic P-value maps (P<0.05) representing regional relative WSS differences between groups. Results Cohort-averaged systolic WSS maps and P-value maps were successfully created for all cohorts and comparisons. The dilation cohort showed significantly lower WSS on 7% of the ascending aorta surface, whereas the stenosis cohort showed significantly higher WSS aorta on 34% the ascending aorta surface. Conclusions The findings of this study demonstrated the feasibility of generating cohort-averaged WSS maps for the visualization and identification of regionally altered WSS in the presence of disease, as compared to healthy controls. PMID:24753241

Maximum stress estimation model for multi-span waler beams with deflections at the supports using average strains.

PubMed

Park, Sung Woo; Oh, Byung Kwan; Park, Hyo Seon

2015-03-30

The safety of a multi-span waler beam subjected simultaneously to a distributed load and deflections at its supports can be secured by limiting the maximum stress of the beam to a specific value to prevent the beam from reaching a limit state for failure or collapse. Despite the fact that the vast majority of accidents on construction sites occur at waler beams in retaining wall systems, no safety monitoring model that can consider deflections at the supports of the beam is available. In this paper, a maximum stress estimation model for a waler beam based on average strains measured from vibrating wire strain gauges (VWSGs), the most frequently used sensors in construction field, is presented. The model is derived by defining the relationship between the maximum stress and the average strains measured from VWSGs. In addition to the maximum stress, support reactions, deflections at supports, and the magnitudes of distributed loads for the beam structure can be identified by the estimation model using the average strains. Using simulation tests on two multi-span beams, the performance of the model is evaluated by estimating maximum stress, deflections at supports, support reactions, and the magnitudes of distributed loads.

Finite Element Analysis of the Endodontically-treated Maxillary Premolars restored with Composite Resin along with Glass Fiber Insertion in Various Positions.

PubMed

Navimipour, Elmira Jafari; Firouzmandi, Maryam; Mirhashemi, Fatemeh Sadat

2015-04-01

This study evaluated the effect of three methods of glass fiber insertion on stress distribution pattern and cusp movement of the root-filled maxillary premolars using finite element method (FEM) analysis. A three-dimensional (3 D) FEM model of a sound upper premolar tooth and four models of root-filled upper premolars with mesiocclusodistal (MOD) cavities were molded and restored with: (1) Composite resin only (NF); (2) Composite resin along with a ribbon of glass fiber placed in the occlusal third (OF); (3) Composite resin along with a ribbon of glass fiber placed circumferentially in the cervical third (CF), and (4) Composite resin along with occlusal and circumferential fibers (OCF). A static vertical load was applied to calculate the stress distributions. Structural analysis program by Solidworks were used for FEM analysis. Von-Mises stress values and cusp movements induced by occlusal loading were evaluated. Maximum Von-Mises stress of enamel occurred in sound tooth, followed by NF, CF, OF and OCF. Maximum Von-Mises stress of dentin occurred in sound tooth, followed by OF, OCF, CF and NF. Stress distribution patterns of OF and OCF were similar. Maximum overall stress values were concentrated in NF. Although stress distribution patterns of NF and CF were found as similar, CF showed lower stress values. Palatal cusp movement was more than buccal cusp in all of the models. The results of our study indicated that while the circumferential fiber had little effect on overall stress concentration, it provided a more favorable stress distribution pattern in cervical region. The occlusal fiber reduced the average stress in the entire structure but did not reduce cuspal movement. Incorporating glass fiber in composite restorations may alter the stress state within the structure depending on fiber position.

Nondestructive monitoring of fatigue damage evolution in austenitic stainless steel by positron-lifetime measurements

NASA Astrophysics Data System (ADS)

Holzwarth, Uwe; Schaaff, Petra

2004-03-01

Positron-lifetime measurements have been performed on austenitic stainless steel during (i) stress- and (ii) strain-controlled fatigue experiments for different applied stress and strain amplitudes, respectively. For this purpose a generator-detector assembly with a 72Se/72As positron generator [maximum activity 25 μCi (0.9 MBq)] has been mounted on mechanical testing machines in order to measure the positron lifetime without removing the specimens from the load train. The average positron lifetime has been determined by a β+-γ coincidence. The feasibility to use the average positron lifetime for monitoring the evolution of fatigue damage and to predict early failure has been examined. In strain- and stress-controlled experiments the average positron lifetime shows a pronounced increase within the first 10% and 40% of the fatigue life, respectively. In stress-controlled experiments the average positron lifetime at failure depends significantly on the applied stress amplitude. In strain-controlled experiments significantly different positron lifetimes for different applied plastic strain amplitudes are obtained within the first 1.000 fatigue cycles, whereas differences get wiped out during further cycling until failure.

Effect of pinpoint plantar long-wavelength infrared light irradiation on subcutaneous temperature and stress markers

PubMed Central

Ryotokuji, Kenji; Ishimaru, Keisou; Kihara, Kazuhiko; Namiki, Yoshihisa; Hozumi, Nobumichi

2013-01-01

Background and aims: The current investigation was aimed at the development of a novel non-invasive treatment system, “pinpoint plantar long-wavelength infrared light irradiation (PP-LILI)”, which may be able to relieve mental stress and reduce stress-related hormones. Materials (Subjects) and methods: We compared the subcutaneous temperature, blood pressure, the degree of secretion of stress hormones before and after pinpoint irradiations (wavelength: 8–11 μm; output: 30mW). The study enrolled 15 subjects (Japanese healthy adults; 8 males, 7 females; average age 47.8 ± 14.6 years). Two parts of the planter region were irradiated for 15 min respectively. The stress markers such as ACTH, salivary amylase and cortisol were measured. As well, core body temperature and blood pressure were analyzed before and after the irradiation. Results: A series of experiments revealed increased body temperature, decreased levels of blood pressure and stress markers described above after the irradiation. Conclusions: These results clearly suggest that the PP-LILI system will be quite useful for relieving stress and improvement of homeostatic functions in the body. PMID:24155554

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lewis, John R.; Brooks, Dusty Marie

In pressurized water reactors, the prevention, detection, and repair of cracks within dissimilar metal welds is essential to ensure proper plant functionality and safety. Weld residual stresses, which are difficult to model and cannot be directly measured, contribute to the formation and growth of cracks due to primary water stress corrosion cracking. Additionally, the uncertainty in weld residual stress measurements and modeling predictions is not well understood, further complicating the prediction of crack evolution. The purpose of this document is to develop methodology to quantify the uncertainty associated with weld residual stress that can be applied to modeling predictions andmore » experimental measurements. Ultimately, the results can be used to assess the current state of uncertainty and to build confidence in both modeling and experimental procedures. The methodology consists of statistically modeling the variation in the weld residual stress profiles using functional data analysis techniques. Uncertainty is quantified using statistical bounds (e.g. confidence and tolerance bounds) constructed with a semi-parametric bootstrap procedure. Such bounds describe the range in which quantities of interest, such as means, are expected to lie as evidenced by the data. The methodology is extended to provide direct comparisons between experimental measurements and modeling predictions by constructing statistical confidence bounds for the average difference between the two quantities. The statistical bounds on the average difference can be used to assess the level of agreement between measurements and predictions. The methodology is applied to experimental measurements of residual stress obtained using two strain relief measurement methods and predictions from seven finite element models developed by different organizations during a round robin study.« less

Compassion satisfaction, burnout, and secondary traumatic stress in UK therapists who work with adult trauma clients

PubMed Central

Sodeke-Gregson, Ekundayo A.; Holttum, Sue; Billings, Jo

2013-01-01

Background Therapists who work with trauma clients are impacted both positively and negatively. However, most studies have tended to focus on the negative impact of the work, the quantitative evidence has been inconsistent, and the research has primarily been conducted outside the United Kingdom. Objectives This study aimed to assess the prevalence of, and identify predictor variables for, compassion satisfaction, burnout, and secondary traumatic stress in a group of UK therapists (N=253) working with adult trauma clients. Method An online questionnaire was developed which used The Professional Quality of Life Scale (Version 5) to assess compassion satisfaction, burnout, and secondary traumatic stress and collect demographics and other pertinent information. Results Whilst the majority of therapists scored within the average range for compassion satisfaction and burnout, 70% of scores indicated that therapists were at high risk of secondary traumatic stress. Maturity, time spent engaging in research and development activities, a higher perceived supportiveness of management, and supervision predicted higher potential for compassion satisfaction. Youth and a lower perceived supportiveness of management predicted higher risk of burnout. A higher risk of secondary traumatic stress was predicted in therapists engaging in more individual supervision and self-care activities, as well as those who had a personal trauma history. Conclusions UK therapists working with trauma clients are at high risk of being negatively impacted by their work, obtaining scores which suggest a risk of developing secondary traumatic stress. Of particular note was that exposure to trauma stories did not significantly predict secondary traumatic stress scores as suggested by theory. However, the negative impact of working with trauma clients was balanced by the potential for a positive outcome from trauma work as a majority indicated an average potential for compassion satisfaction. PMID:24386550

[Stress in nurses at a hemodynamics ward in Rio Grande do Sul, Brazil].

PubMed

Linch, Graciele Fernanda da Costa; Guido, Laura de Azevedo

2011-03-01

This study aimed to evaluate the relationship between stress and symptoms reported by nurses working in units hemodynamics. Data were collected through a questionnaire. For analysis, the results were considered statistically significant if p < 0.05, with an interval of 95% confidence. The population consisted of 63 nurses with a predominance of females (90.5%) and average age of 35.24 (+/- 8.21) years. Most participants werepostgraduate (77.8%) and did not have another job (77.8%). In relation to stress, 52.4% of nurses had an average between 1.11 and 1.97, classified as medium stress, and the critical situations domain presented the highest score (1.63 +/- 0.29). Regarding symptoms, the domain skeletal muscle had a higher average (1.39 +/- 0.94). In this study, there was high significant positive correlation between stress and symptoms (r = 0.629, p < 0.001), thus it is concluded that stress is directly related to the symptomspresented by the nurses.

A new momentum integral method for approximating bed shear stress

NASA Astrophysics Data System (ADS)

Wengrove, M. E.; Foster, D. L.

2016-02-01

In nearshore environments, accurate estimation of bed stress is critical to estimate morphologic evolution, and benthic mass transfer fluxes. However, bed shear stress over mobile boundaries in wave environments is notoriously difficult to estimate due to the non-equilibrium boundary layer. Approximating the friction velocity with a traditional logarithmic velocity profile model is common, but an unsteady non-uniform flow field violates critical assumptions in equilibrium boundary layer theory. There have been several recent developments involving stress partitioning through an examination of the momentum transfer contributions that lead to improved estimates of the bed stress. For the case of single vertical profile observations, Mehdi et al. (2014) developed a full momentum integral-based method for steady-unidirectional flow that integrates the streamwise Navier-Stokes equation three times to an arbitrary position within the boundary layer. For the case of two-dimensional velocity observations, Rodriguez-Abudo and Foster (2014) were able to examine the momentum contributions from waves, turbulence and the bedform in a spatial and temporal averaging approach to the Navier-Stokes equations. In this effort, the above methods are combined to resolve the bed shear stress in both short and long wave dominated environments with a highly mobile bed. The confluence is an integral based approach for determining bed shear stress that makes no a-priori assumptions of boundary layer shape and uses just a single velocity profile time series for both the phase dependent case (under waves) and the unsteady case (under solitary waves). The developed method is applied to experimental observations obtained in a full scale laboratory investigation (Oregon State's Large Wave Flume) of the nearbed velocity field over a rippled sediment bed in oscillatory flow using both particle image velocimetry and a profiling acoustic Doppler velocimeter. This method is particularly relevant for small scale field observations and laboratory observations.

Lagrangian methods for blood damage estimation in cardiovascular devices - How numerical implementation affects the results

PubMed Central

Marom, Gil; Bluestein, Danny

2016-01-01

Summary This paper evaluated the influence of various numerical implementation assumptions on predicting blood damage in cardiovascular devices using Lagrangian methods with Eulerian computational fluid dynamics. The implementation assumptions that were tested included various seeding patterns, stochastic walk model, and simplified trajectory calculations with pathlines. Post processing implementation options that were evaluated included single passage and repeated passages stress accumulation and time averaging. This study demonstrated that the implementation assumptions can significantly affect the resulting stress accumulation, i.e., the blood damage model predictions. Careful considerations should be taken in the use of Lagrangian models. Ultimately, the appropriate assumptions should be considered based the physics of the specific case and sensitivity analysis, similar to the ones presented here, should be employed. PMID:26679833

A Life Events Scale for Armed Forces personnel

PubMed Central

Chaudhury, Suprakash; Srivastava, Kalpana; Raju, M.S.V. Kama; Salujha, S.K.

2006-01-01

Background: Armed Forces personnel are routinely exposed to a number of unique stressful life events. None of the available scales are relevant to service personnel. Aim: To construct a scale to measure life events in service personnel. Methods: In the first stage of the study open-ended questions along with items generated by the expert group by consensus method were administered to 50 soldiers. During the second stage a scale comprising 59 items and open-ended questions was administered to 165 service personnel. The final scale of 52 items was administered to 200 service personnel in group setting. Weightage was assigned on a 0 to 100 range. For normative study the Armed Forces Medical College Life Events Scale (AFMC LES) was administered to 1200 Army, 100 Air Force and 100 Navy personnel. Results: Service personnel experience an average of 4 life events in past one year and 13 events in a life-time. On an average service personnel experience 115 life change unit scores in past one year and 577 life change unit scores in life-time on the AFMC LES. The scale has concurrent validity when compared with the Presumptive Stressful Life Events Scale (PSLES). There is internal consistency in the scale with the routine items being rated very low. There is a pattern of uniformity with the civilian counterparts along with differences in the items specific to service personnel. Conclusions: The AFMC LES includes the unique stresses of service personnel that are not included in any life events scale available in India or in the west and should be used to assess stressful life events in service personnel. PMID:20844647

Mind-Body Skills Training for Resident Wellness: A Pilot Study of a Brief Mindfulness Intervention

PubMed Central

Romcevich, Laura E; Reed, Suzanne; Flowers, Stacy R; Kemper, Kathi J; Mahan, John D

2018-01-01

Background: Interventions to address burnout include mind-body skills training (MBST), but few studies have evaluated the feasibility of MBST for busy pediatric residents. Objective: In this pilot study, we tested the feasibility of a brief MBST intervention, using in-person peer-led training supported by online modules, to decrease stress and burnout in pediatric resident physicians. Methods: Of 99 (10%) residents, 10 residents at Nationwide Children’s Hospital in Ohio participated in up to four 90-minute MBST sessions more than 1 month, led by a co-resident with 5 years of informal training in mind-body skills. Participants were offered 8 assigned online modules through OSU Center for Integrative Health and Wellness. Measures including Maslach Burnout Inventory (MBI), Cohen’s Perceived Stress, Smith’s Brief Resilience, Cognitive and Affective Mindfulness Scale-Revised, and Neff’s Self-Compassion Scale (NSS) were administered before (T1) and after (T2) the course. Participants were offered optional monthly “maintenance” sessions for 6 months and completed a third set of measures at this follow-up (T3). Results: The residents completed an average of 4.3/8 online modules and attended an average of 2.8/4 in-person sessions. There was significant improvement in positive attitude, perceived stress, and resilience post intervention (T2). Follow-up evaluation (T3) also demonstrated significant improvement in burnout (depersonalization) and mindfulness. More than 75% of participants found the course worthwhile. Conclusions: A short mixed-method mindfulness-based skills course may be a practical way to offer resilience and stress management training to busy resident physicians. PMID:29780891

Effects of Heat Treatment on SiC-SiC Ceramic Matrix Composites

NASA Astrophysics Data System (ADS)

Knauf, Michael W.

Residual stresses resulting from the manufacturing process found within a silicon carbide/silicon carbide (SiC/SiC) ceramic matrix composite were thoroughly investigated through the use of high-energy X-ray diffraction and Raman microspectroscopy. The material system studied was a Rolls-Royce composite produced with Hi-Nicalon fibers woven into a five harness satin weave, coated with boron nitride and silicon carbide interphases, and subsequently infiltrated with silicon carbide particles and a silicon matrix. Constituent stress states were measured before, during, and after heat treatments ranging from 900 °C to 1300 °C for varying times between one and sixty minutes. Stress determination methods developed through these analyses can be utilized in the development of ceramic matrix composites and other materials employing boron-doped silicon. X-ray diffraction experiments were performed at the Argonne National Laboratory Advanced Photon Source to investigate the evolution of constituent stresses through heat treatment, and determine how stress states are affected at high temperature through in situ measurements during heat treatments up to 1250 °C for 30 minutes. Silicon carbide particles in the as-received condition exhibited a nearly isotropic stress state with average tensile stresses of approximately 300 MPa. The silicon matrix exhibited a complimentary average compressive stress of approximately 300 MPa. Strong X-ray diffraction evidence is presented demonstrating solid state boron diffusion and increased boron solubility found in silicon throughout heat treatment. While the constituent stress states did evolve through the heat treatment cycles, including approaching nearly stress-free conditions at temperatures close to the manufacturing temperature, no permanent relaxation of stress was observed. Raman spectroscopy was utilized to investigate stresses found within silicon carbide particles embedded within the matrix and the silicon matrix as an alternate method of measurement. The stresses determined through Raman spectroscopy were comparable to those determined through X-ray diffraction. Neither silicon carbide particles nor silicon were significantly affected through heat treatment, corroborating the X-ray diffraction results. Silicon present near fibers exhibited less compressive stress than the majority of silicon found throughout the matrix. Measurements were taken in situ and ex situ to determine the temporal evolution of the stress state at various temperatures. Heat treatments up to 1300 °C for one hour failed to produce significant changes in the residual stress state of the composite constituents. A strong trend was identified in the Raman silicon signal manifesting a continuously decreasing wavenumber with increasing heat treatment temperature between 1100 °C and 1300 °C in timeframes of less than one minute. This was found to be due to a continuously increasing electronic activation of boron within the silicon matrix, stemming from an increase of boron atoms occupying substitutional silicon lattice sites while covalently bonded to surrounding silicon. A methodology to determine the residual stress state of silicon exhibiting varying degrees of boron dopant is proposed by accounting for the changes in the Raman profile parameters. This method also allows for observing activated boron segregation in various matrix areas; wavenumber gradients in these areas exist which have been misconstrued in literature as large variations in stress, while in fact the variability is likely relatively benign.

Patient safety culture and job stress among nurses in Mazandaran, Iran.

PubMed

Asefzadeh, Saeed; Kalhor, Rohollah; Tir, Mohammad

2017-12-01

Paying attention to patient safety is a basic right and a necessary issue in providing medical care, and failure to observe it leads to irreparable damage. One of the factors affecting an individuals' performance in an organization is stress, which also endangers their health. To determine the relationship between patient safety culture and levels of job stress among the nurses working in the hospitals affiliated with Mazandaran University of Medical Sciences. The present study was carried out using a cross-sectional method in the hospitals affiliated with Mazandaran University of Medical Sciences in 2016. A multistage stratified sampling method using a Morgan Table was employed to select 380 nurses as the study sample from among 3,180 nurses. They were selected by a multistage stratified sampling method. The study instruments were Stinemetz Standard Job Stress Questionnaire and Hospital Survey on Patient Safety Culture (HSOPSC). After the required data were collected, they were analyzed using descriptive and inferential statistical methods (Pearson correlation, independent-samples t-test, and ANOVA) through SPSS version 23. The results of the present study showed that 75% of the nurses experienced average and high levels of stress. Among different dimensions of safety culture, organizational learning and handoffs and transitions obtained the highest and the lowest scores, respectively (72.5 and 24.5). The mean score of safety culture dimensions was 51.52. The results of the Pearson correlation test showed that there was a direct significant relationship between different dimensions of safety culture among nurses and the level of stress (p≤0.05). According to the findings, patient safety should be considered as a strategic priority for the senior managers of the health system. In order to enhance patient safety, managers should pay special attention to evaluating safety culture in organizations that deliver health service, especially hospitals.

Random Process Simulation for stochastic fatigue analysis. Ph.D. Thesis - Rice Univ., Houston, Tex.

NASA Technical Reports Server (NTRS)

Larsen, Curtis E.

1988-01-01

A simulation technique is described which directly synthesizes the extrema of a random process and is more efficient than the Gaussian simulation method. Such a technique is particularly useful in stochastic fatigue analysis because the required stress range moment E(R sup m), is a function only of the extrema of the random stress process. The family of autoregressive moving average (ARMA) models is reviewed and an autoregressive model is presented for modeling the extrema of any random process which has a unimodal power spectral density (psd). The proposed autoregressive technique is found to produce rainflow stress range moments which compare favorably with those computed by the Gaussian technique and to average 11.7 times faster than the Gaussian technique. The autoregressive technique is also adapted for processes having bimodal psd's. The adaptation involves using two autoregressive processes to simulate the extrema due to each mode and the superposition of these two extrema sequences. The proposed autoregressive superposition technique is 9 to 13 times faster than the Gaussian technique and produces comparable values for E(R sup m) for bimodal psd's having the frequency of one mode at least 2.5 times that of the other mode.

Outcomes and radiographic findings of anatomic press-fit radial head arthroplasty.

PubMed

Levy, Jonathan C; Formaini, Nathan T; Kurowicki, Jennifer

2016-05-01

Radial head arthroplasty (RHA) is a popular method of treatment for complex fractures of the radial head. The purpose of this study was to investigate patient outcomes and radiographic findings associated with a single anatomic monopolar press-fit radial head system commonly used for the treatment of radial head fractures. A retrospective review of prospectively collected data was performed for a consecutive series of patients treated with a press-fit anatomically designed RHA between November 2007 and April 2014. The most recent radiographs were evaluated for loosening, stress shielding, and instability. Postoperative motion and outcomes were reported at most recent follow-up. At an average follow-up of 30 months, 6 of the 15 patients (40%) demonstrated radiographic loosening. Six of the 9 patients (67%) without loosening demonstrated stress shielding (average, 6 mm). Functional outcome scores included a mean American Shoulder and Elbow Surgeons score of 70, Mayo Elbow Performance Score of 85, visual analog scale score for pain of 2, visual analog scale score for function of 7, and Single Assessment Numeric Evaluation score of 75. Average flexion-extension arc was 14° to 138°, and average pronation-supination was 75° to 74°. All 6 of the patients with radiographic loosening had undergone RHA with an associated ligamentous injury repair. Satisfaction among patients was high as no patient reported an unsatisfactory outcome. The use of an anatomic, press-fit monopolar RHA in the management of acute complex radial head fractures has yielded excellent clinical outcomes despite high rates of radiographic loosening and stress shielding. Press-fit RHA in the setting of ligamentous injury warrants further investigation because of a high rate of implant loosening observed. Copyright © 2016 Journal of Shoulder and Elbow Surgery Board of Trustees. Published by Elsevier Inc. All rights reserved.

Maximum Stress Estimation Model for Multi-Span Waler Beams with Deflections at the Supports Using Average Strains

PubMed Central

Park, Sung Woo; Oh, Byung Kwan; Park, Hyo Seon

2015-01-01

The safety of a multi-span waler beam subjected simultaneously to a distributed load and deflections at its supports can be secured by limiting the maximum stress of the beam to a specific value to prevent the beam from reaching a limit state for failure or collapse. Despite the fact that the vast majority of accidents on construction sites occur at waler beams in retaining wall systems, no safety monitoring model that can consider deflections at the supports of the beam is available. In this paper, a maximum stress estimation model for a waler beam based on average strains measured from vibrating wire strain gauges (VWSGs), the most frequently used sensors in construction field, is presented. The model is derived by defining the relationship between the maximum stress and the average strains measured from VWSGs. In addition to the maximum stress, support reactions, deflections at supports, and the magnitudes of distributed loads for the beam structure can be identified by the estimation model using the average strains. Using simulation tests on two multi-span beams, the performance of the model is evaluated by estimating maximum stress, deflections at supports, support reactions, and the magnitudes of distributed loads. PMID:25831087

Normal and radial impact of composites with embedded penny-shaped cracks

NASA Technical Reports Server (NTRS)

Sih, G. C.

1979-01-01

A method is developed for the dynamic stress analysis of a layered composite containing an embedded penny-shaped crack and subjected to normal and radial impact. The material properties of the layers are chosen such that the crack lies in a layer of matrix material while the surrounding material possesses the average elastic properties of a two-phase medium consisting of a large number of fibers embedded in the matrix. Quantitatively, the time-dependent stresses near the crack border can be described by the dynamic stress intensity factors. Their magnitude depends on time, on the material properties of the composite and on the relative size of the crack compared to the composite local geometry. Results obtained show that, for the same material properties and geometry of the composite, the dynamic stress intensity factors for an embedded (penny-shaped) crack reach their peak values within a shorter period of time and with a lower magnitude than the corresponding dynamic stress intensity factors for a through-crack.

A Comparison of Brain Wave Patterns of High and Low Grade Point Average Students During Rest, Problem Solving, and Stress Situations.

ERIC Educational Resources Information Center

Montor, Karel

The purpose of this study was to compare brain wave patterns produced by high and low grade point average students, while they were resting, solving problems, and subjected to stress situations. The study involved senior midshipmen at the United States Naval Academy. The high group was comprised of those whose cumulative grade point average was…

Chronic Stress and Fatigue-Related Quality of Life after Mild-to-Moderate Traumatic Brain Injury (TBI)

PubMed Central

Bay, Esther; de-Leon, Marita B.

2010-01-01

Objective To determine relationships between chronic stress, fatigue-related quality of life (QOL-F) and related covariates after mild-to-moderate traumatic brain injury (TBI). Design Observational and cross-sectional Participants A total of 84 community-dwelling individuals with mild-to-moderate TBI recruited from multiple out-patient rehabilitation clinics assessed on average 15 months after injury. Method Data were collected with self-report surveys and chart abstraction. Measures Neurofunctional Behavioral Inventory, Perceived Stress Scale-14, Impact of Events Scale, McGill Pain Short-form Scale, and modified version of the Fatigue Impact Scale. Results Fatigue-related quality of life was associated with somatic symptoms, perceived situational stress, but not with event-related stress (PTSD symptoms) related to index TBI, pre-injury demographic, or post-injury characteristics. Somatic symptoms and chronic situational stress accounted for 42% of the variance in QOL (F). Conclusions QOL (F) in community-dwelling individuals with mild-to- moderate TBI is associated with chronic situational stress and somatic symptoms. Symptom management strategies may need to include general stress management to reduce fatigue burden and improve quality of life. PMID:21169862

Primary teachers' knowledge and acquisition of stress relieving strategies.

PubMed

Cockburn, A D

1996-09-01

Over the last 20 years there have been numerous studies of teacher stress but little is known of how teachers acquire coping strategies; their knowledge of those available to them and their opinion of these techniques. A total of 335 Norfolk primary teachers responded to a postal questionnaire providing biographical details; levels of job satisfaction and work related stress; responses to a range of commonly advocated techniques to reduce teacher stress and their opinion on who-if anyone-should take more responsibility for reducing teacher stress. On average the respondents were aware of 35 stress reduction strategies. The most effective strategies were ensuring that one understood what one was about to teach and thorough lesson preparation. A significant proportion of practitioners said that they would not consider seeking expert sources of advice. A total of 89 per cent of practitioners reported that they acquired at least some strategies through their own experience. It was concluded that the issue of teacher stress needs to be considered at governmental, school and individual levels. In the light of some resistance to traditional methods of stress reduction, the implications for initial and in-service training were explored.

Job demand-control and job stress at work: A cross-sectional study among prison staff

PubMed Central

Akbari, Jafar; Akbari, Rouhollah; Shakerian, Mahnaz; Mahaki, Behzad

2017-01-01

Introduction: Job stress can impose significant costs to the workplaces and organizations due to some issues such as absenteeism, less productivity, and medical costs. Job overload and lack of decision latitude can lead to job stress. The current study aimed to investigate the job demands and control as predictor of job stress and its relationship, with some of the demographic characteristics of Iranian prison staff. Materials and Methods: This study was performed on 171 male employees working in four prisons located in Ilam, Iran. The sampling method was census and all four prisons’ staff were selected to respond the Job Content Questionnaires. Finally, the data were analyzed using t-test or independent samples test as well as SPSS 20. Results: The highest amount of job demand (mean = 21.28) and the lowest amount of job control on average (9.76) were reported by those staff working in Darehshahr prison. There was also a significant relationship between job post and job control among the prison staff (β = −0.375, P = 0.001). Conclusion: The level of job stress reported by prison staff was high in this study mainly caused by high job demand and low job control, especially in Darehshahr prison staff. PMID:28546980

Estimation of lattice strain in nanocrystalline RuO2 by Williamson-Hall and size-strain plot methods

NASA Astrophysics Data System (ADS)

Sivakami, R.; Dhanuskodi, S.; Karvembu, R.

2016-01-01

RuO2 nanoparticles (RuO2 NPs) have been successfully synthesized by the hydrothermal method. Structure and the particle size have been determined by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM) and transmission electron microscopy (TEM). UV-Vis spectra reveal that the optical band gap of RuO2 nanoparticles is red shifted from 3.95 to 3.55 eV. BET measurements show a high specific surface area (SSA) of 118-133 m2/g and pore diameter (10-25 nm) has been estimated by Barret-Joyner-Halenda (BJH) method. The crystallite size and lattice strain in the samples have been investigated by Williamson-Hall (W-H) analysis assuming uniform deformation, deformation stress and deformation energy density, and the size-strain plot method. All other relevant physical parameters including stress, strain and energy density have been calculated. The average crystallite size and the lattice strain evaluated from XRD measurements are in good agreement with the results of TEM.

Electric pulses used in electrochemotherapy and electrogene therapy do not significantly change the expression profile of genes involved in the development of cancer in malignant melanoma cells.

PubMed

Mlakar, Vid; Todorovic, Vesna; Cemazar, Maja; Glavac, Damjan; Sersa, Gregor

2009-08-26

Electroporation is a versatile method for in vitro or in vivo delivery of different molecules into cells. However, no study so far has analysed the effects of electric pulses used in electrochemotherapy (ECT pulses) or electric pulses used in electrogene therapy (EGT pulses) on malignant cells. We studied the effect of ECT and EGT pulses on human malignant melanoma cells in vitro in order to understand and predict the possible effect of electric pulses on gene expression and their possible effect on cell behaviour. We used microarrays with 2698 different oligonucleotides to obtain the expression profile of genes involved in apoptosis and cancer development in a malignant melanoma cell line (SK-MEL28) exposed to ECT pulses and EGT pulses. Cells exposed to ECT pulses showed a 68.8% average survival rate, while cells exposed to EGT pulses showed a 31.4% average survival rate. Only seven common genes were found differentially expressed in cells 16 h after exposure to ECT and EGT pulses. We found that ECT and EGT pulses induce an HSP70 stress response mechanism, repress histone protein H4, a major protein involved in chromatin assembly, and down-regulate components involved in protein synthesis. Our results show that electroporation does not significantly change the expression profile of major tumour suppressor genes or oncogenes of the cell cycle. Moreover, electroporation also does not changes the expression of genes involved in the stability of DNA, supporting current evidence that electroporation is a safe method that does not promote tumorigenesis. However, in spite of being considered an isothermal method, it does to some extent induce stress, which resulted in the expression of the environmental stress response mechanism, HSP70.

Apparatus for monitoring crystal growth

DOEpatents

Sachs, Emanual M.

1981-01-01

A system and method are disclosed for monitoring the growth of a crystalline body from a liquid meniscus in a furnace. The system provides an improved human/machine interface so as to reduce operator stress, strain and fatigue while improving the conditions for observation and control of the growing process. The system comprises suitable optics for forming an image of the meniscus and body wherein the image is anamorphic so that the entire meniscus can be viewed with good resolution in both the width and height dimensions. The system also comprises a video display for displaying the anamorphic image. The video display includes means for enhancing the contrast between any two contrasting points in the image. The video display also comprises a signal averager for averaging the intensity of at least one preselected portions of the image. The value of the average intensity, can in turn be utilized to control the growth of the body. The system and method are also capable of observing and monitoring multiple processes.

Average static stress drops for heterogeneous slip distributions: Comparison of several measures and implications for energy partition in earthquakes

NASA Astrophysics Data System (ADS)

Noda, H.; Lapusta, N.; Kanamori, H.

2010-12-01

Static stress drop is often estimated using the seismic moment and rupture area based on a model for uniform stress drop distribution; we denote this estimate by Δσ_M. Δσ_M is sometimes interpreted as the spatial average of stress change over the ruptured area, denoted here as Δσ_A, and used accordingly, for example, to discuss the relation between recurrence interval and the healing of the frictional surface in a system with one degree of freedom [e.g., Marone, 1998]. Δσ_M is also used to estimate available energy (defined as the strain energy change computed using the final stress state as the reference one) and radiation efficiency [e.g., Venkataraman and Kanamori, 2004]. In this work, we define a stress drop measure, Δσ_E, that would enter the exact computation of available energy and radiation efficiency. The three stress drop measures - Δσ_M that can be estimated from observations, Δσ_A, and Δσ_E - are equal if the static stress change is spatially uniform, and that motivates substituting Δσ_M for the other two quantities in applications. However, finite source inversions suggest that the stress change is heterogeneous in natural earthquakes [e.g., Bouchon, 1997]. Since Δσ_M is the average of stress change weighted by slip distribution due to a uniform stress drop [Madariaga, 1979], Δσ_E is the average of stress change weighted by actual slip distribution in the event (this work), and Δσ_A is the simple spatial average of stress change, the three measures should, in general, be different. Here, we investigate the effect of heterogeneity aiming to understand how to use the seismological estimates of stress drop appropriately. We create heterogeneous slip distributions for both circular and rectangular planar ruptures using the approach motivated by Liu-Zeng et al. [2005] and Lavalleé et al [2005]. We find that, indeed, the three stress drop measures differ in our scenarios. In particular, heterogeneity increases Δσ_E and thus the available energy when the seismic moment (and hence Δσ_M) is preserved. So using Δσ_M instead of Δσ_E would underestimate available energy and hence overestimate radiation efficiency. For a range of parameters, Δσ_E is well-approximated by the seismic estimate Δσ_M if the latter is computed using a modified (decreased) rupture area that excludes low-slipped regions; a qualitatively similar procedure is already being used in practice [Somerville et al, 1999].

Experimental analysis and application of the effect of stress on continental shale reservoir brittleness

NASA Astrophysics Data System (ADS)

Yin, Shuai; Lv, Dawei; Jin, Lin; Ding, Wenlong

2018-04-01

Hydraulic fracturing is an effective measure of reservoir modification for the development of shale gas. The evaluation of rock brittleness can provide a basis for the optimization of fracturing. In this paper, the effect of stress on the brittleness of shale is systematically analyzed by designing triaxial mechanics tests. The strain analysis method was used to evaluate the shale brittleness. The research indicates that, with the increase of effective confining pressure, the value of the brittleness index (B 1) decreases. There is a linear and positive correlation between the average reduction ratio of B 1 and the buried depth. The stress has a significant effect on the shale brittleness. Therefore, the rock brittleness can be overestimated without considering the influence of the buried depth or the stress of formation when using the mineral composition method. Being affected by the stress, when the brittle mineral content of the shale reservoir is 70%, 65%, 60%, and 55%, the lower limit depth of the shale gas development is 5000 m, 4400 m, 3000 m, and 1800 m, respectively. However, when the brittle mineral content of the shale is less than 50%, the brittleness index is less than 50% in all of the buried depths. In this case, the shale will not have any commercial development potential. The logging interpretation results of the brittleness index conducted with stress correction are more consistent with the real situation, and thus, this method can be better used to help the optimization of the fracturing intervals of shale gas.

Earthquake stress drops, ambient tectonic stresses and stresses that drive plate motions

USGS Publications Warehouse

Hanks, T.C.

1977-01-01

A variety of geophysical observations suggests that the upper portion of the lithosphere, herein referred to as the elastic plate, has long-term material properties and frictional strength significantly greater than the lower lithosphere. If the average frictional stress along the non-ridge margin of the elastic plate is of the order of a kilobar, as suggested by the many observations of the frictional strength of rocks at mid-crustal conditions of pressure and temperature, the only viable mechanism for driving the motion of the elastic plate is a basal shear stress of several tens of bars. Kilobars of tectonic stress are then an ambient, steady condition of the earth's crust and uppermost mantle. The approximate equality of the basal shear stress and the average crustal earthquake stress drop, the localization of strain release for major plate margin earthquakes, and the rough equivalence of plate margin slip rates and gross plate motion rates suggest that the stress drops of major plate margin earthquakes are controlled by the elastic release of the basal shear stress in the vicinity of the plate margin, despite the existence of kilobars of tectonic stress existing across vertical planes parallel to the plate margin. If the stress differences available to be released at the time of faulting are distributed in a random, white fasbion with a mean-square value determined by the average earthquake stress drop, the frequency of occurrence of constant stress drop earthquakes will be proportional to reciprocal faulting area, in accordance with empirically known frequency of occurrence statistics. ?? 1977 Birkha??user Verlag.

Occupational stress and related factors among surgical residents in Korea

PubMed Central

Kang, Sanghee; Jo, Hye Sung; Lee, Ji Sung; Kim, Chong Suk

2015-01-01

Purpose The application rate for surgical residents in Korea has continuously decreased over the past few years. The demanding workload and the occupational stress of surgical training are likely causes of this problem. The aim of this study was to investigate occupational stress and its related factors in Korean surgical residents. Methods With the support of the Korean Surgical Society, we conducted an electronic survey of Korean surgical residents related to occupational stress. We used the Korean Occupational Stress Scale (KOSS) to measure occupational stress. We analyzed the data focused on the stress level and the factors associated with occupational stress. Results The mean KOSS score of the surgical residents was 55.39, which was significantly higher than that of practicing surgeons (48.16, P < 0.001) and the average score of specialized professionals (46.03, P < 0.001). Exercise was the only factor found to be significantly associated with KOSS score (P = 0.001) in univariate analysis. However, in multiple linear regression analysis, the mean number of assigned patients, resident occupation rate and exercise were all significantly associated with KOSS score. Conclusion Surgical residents have high occupational stress compared to practicing surgeons and other professionals. Their mean number of assigned patients, resident recruitment rate and exercise were all significantly associated with occupational stress for surgical residents. PMID:26576407

Stress Drop and Its Relationship to Radiated Energy, Ground Motion and Uncertainty

NASA Astrophysics Data System (ADS)

Baltay, A.

2014-12-01

Despite the seemingly diverse circumstances under which crustal earthquakes occur, scale-invariant stress drop and apparent stress, the ratio of radiated seismic energy to moment, is observed. The magnitude-independence of these parameters is central to our understanding of both earthquake physics and strong ground motion genesis. Estimates of stress drop and radiated energy, however, display large amounts of scatter potentially masking any secondary trends in the data. We investigate sources of this uncertainty within the framework of constant stress drop and apparent stress. We first re-visit estimates of energy and stress drop from a variety of earthquake observations and methods, for events ranging from magnitude ~2 to ~9. Using an empirical Green's function (eGf) deconvolution method, which removes the path and site effects, radiated energy and Brune stress drop are estimated for both regional events in the western US and Eastern Honshu, Japan from the HiNet network, as well as teleseismically recorded global great earthquakes [Baltay et al., 2010, 2011, 2014]. In addition to eGf methods, ground-motion based metrics for stress drop are considered, using both KikNet data from Japan [Baltay et al., 2013] and the NGA-West2 data, a very well curated ground-motion database. Both the eGf-based stress drop estimates and those from the NGA-West2 database show a marked decrease in scatter, allowing us to identify deterministic secondary trends in stress drop. We find both an increasing stress drop with depth, as well as a larger stress drop of about 30% on average for mainshock events as compared to on-fault aftershocks. While both of these effects are already included in some ground-motion prediction equations (GMPE), many previous seismological studies have been unable to conclusively uncover these trends because of their considerable scatter. Elucidating these effects in the context of reduced and quantified epistemic uncertainty can help both seismologists and engineers to understand the true aleatory variability of the earthquake source, which may be due to the complex and diverse circumstances under which these earthquake occur and which we are yet unable to model.

Tectonic stress orientations and magnitudes, and friction of faults, deduced from earthquake focal mechanism inversions over the Korean Peninsula

NASA Astrophysics Data System (ADS)

Soh, Inho; Chang, Chandong; Lee, Junhyung; Hong, Tae-Kyung; Park, Eui-Seob

2018-05-01

We characterize the present-day stress state in and around the Korean Peninsula using formal inversions of earthquake focal mechanisms. Two different methods are used to select preferred fault planes in the double-couple focal mechanism solutions: one that minimizes average misfit angle and the other choosing faults with higher instability. We invert selected sets of fault planes for estimating the principal stresses at regularly spaced grid points, using a circular-area data-binning method, where the bin radius is optimized to yield the best possible stress inversion results based on the World Stress Map quality ranking scheme. The inversions using the two methods yield well constrained and fairly comparable results, which indicate that the prevailing stress regime is strike-slip, and the maximum horizontal principal stress (SHmax) is oriented ENE-WSW throughout the study region. Although the orientation of the stresses is consistent across the peninsula, the relative stress magnitude parameter (R-value) varies significantly, from 0.22 in the northwest to 0.89 in the southeast. Based on our knowledge of the R-values and stress regime, and using a value for vertical stress (Sv) estimated from the overburden weight of rock, together with a value for the maximum differential stress (based on the Coulomb friction of faults optimally oriented for slip), we estimate the magnitudes of the two horizontal principal stresses. The horizontal stress magnitudes increase from west to east such that SHmax/Sv ratio rises from 1.5 to 2.4, and the Shmin/Sv ratio from 0.6 to 0.8. The variation in the magnitudes of the tectonic stresses appears to be related to differences in the rigidity of crustal rocks. Using the complete stress tensors, including both orientations and magnitudes, we assess the possible ranges of frictional coefficients for different types of faults. We show that normal and reverse faults have lower frictional coefficients than strike-slip faults, suggesting that the former types of faults can be activated under a strike-slip stress regime. Our observations of the seismicity, with normal faulting concentrated offshore to the northwest and reverse faulting focused offshore to the east, are compatible with the results of our estimates of stress magnitudes.

Depression, Stress and Body Fat are Associated with Binge Eating in a Community Sample of African American and Hispanic Women

PubMed Central

Adamus-Leach, Heather J.; Wilson, Penny L.; O’Connor, Daniel P.; Rhode, Paula C.; Mama, Scherezade K.; Lee, Rebecca E.

2013-01-01

Objective The purpose of this study was to examine the relationships among depressive symptoms, stress and severity of binge eating symptoms in a community sample of African American and Hispanic or Latina women. Method Women (African American n=127, Hispanic or Latina n=44) completed measures of body composition, stress, depression, and binge eating. Results Scores on a depressive symptom scale indicated that 24.0% of participants exhibited clinically significant levels of depressive symptoms. Mean binge eating scores were below the threshold for clinically diagnosed binge eating (12.99±7.90). Mean stressful event scores were 25.86±14.26 and the average stress impact score was 78.36±55.43. Linear regression models found that body composition, stress impact score, and being classified as having clinically significant levels of depression, were associated with severity of binge eating symptoms. Conclusion Higher levels of percent body fat, a CES-D score ≥16 and higher WSI-Impact scores were associated with greater severity of binge eating symptoms. PMID:23760851

Effect of root canal treatment procedures with a novel rotary nickel titanium instrument (TRUShape) on stress in mandibular molars: a comparative finite element analysis.

PubMed

Bonessio, Noemi; Arias, Ana; Lomiento, Guiseppe; Peters, Ove A

2017-01-01

The aim of this study was to investigate and compare, via finite element analysis (FEA), the effects of endodontic access and canal preparation on stress distribution under functional loading of a mandibular molar treated with novel (TRUShape) and conventional (Vortex) rotary root canal preparation instruments. Identical plastic mandibular molars with natural anatomy had all 4 canals shaped with either TRUShape or a conventional rotary, Vortex (#20 and #30, both by Dentsply Tulsa Dental). Finite element analysis was used to evaluate stress distribution in untreated and treated models. Micro-computed tomography (MCT) of the extracted teeth shaped in vitro was used to inform the FEA model regarding the geometry of root canals and external surfaces. Modeling the intact periodontal support and cancellous/cortical bone was based on anatomical data. Profiles of average and maximum von Mises stresses in dentin of the four treated conditions under functional loading were compared to the untreated model. This comparison was performed for each tooth model with and without root canal obturation and composite restoration. On average, the dentin sections with the most changes after preparation were located in the access cavity, with average stress increase up to +5.7, +8.5, +8.9, and +10.2 % for the TRUShape #20, Vortex #20, TRUShape #30 and Vortex #30, respectively, relative to the untreated model. Within the root canal system, the average stress differences were smaller than <5 % with lower values for TRUShape preparation. A reduction of the average stress in the access cavity was observed as an effect of the composite restoration, while about the same von Mises stress' profiles were found into the root canal. In this finite element analysis, preparation of the access cavity resulted in increased von Mises stresses under functional occlusal load. The limited (up to 0.7 %) retained radicular dentin in the TRUShape versus the Vortex cavity proved effective in reducing masticatory stresses. The bonded restoration modeled in this study only partially counterbalance the combined effects of access cavity and root canal preparation.

Sexual Self-concept and Its Relationship to Depression, Stress and Anxiety in Postmenopausal Women

PubMed Central

Heidari, Mohammad; Rafiei, Hossein

2017-01-01

Objectives Women in menopause have the more mood swings than before menopause. At the same time seem to sexual self-concept and sexual aspects of self-knowledge has a great impact on their mental health. This study aimed to investigate the sexual self-concept and its relationship to depression, stress and anxiety in postmenopausal women's. Methods In this descriptive correlation research, 300 of postmenopausal women referred to healthcare and medical treatment centers in Abadeh city were selected by convenience sampling method. The information in this study was collected by using questionnaires of multidimensional sexual self-concept and depression anxiety stress scale 21 (DASS-21). For data analysis, SPSS/17 software was used. Results The results showed the mean score positive sexual self-concept was 41.03 ± 8.66 and the average score of negative sexual self in women's was 110.32 ± 43.05. As well as scores of depression, stress, and anxiety, 35.67%, 32.33% and 37.67% respectively were in severe level. Positive and negative sexual self-concept scores with scores of stress, anxiety, and depression, of post-menopausal women in the confidence of 0.01, is significantly correlated (P < 0.05). Conclusions Being stress, anxiety, and depression in severe level and also a significant correlation between increased stress, anxiety and depression with negative and weak self-concept of women's, it is necessary to devote more careful attention to mental health issues of women's and have appropriate interventions. PMID:28523258

Differences in stress-related ratings between research center and home environments in dementia caregivers using ecological momentary assessment

PubMed Central

Fonareva, Irina; Amen, Alexandra M.; Ellingson, Roger M.; Oken, Barry S.

2012-01-01

Background Clinicians and researchers working with dementia caregivers typically assess caregiver stress in a clinic or research center, but caregivers’ stress is rooted at home where they provide care. The study aimed to compare ratings of stress-related measures obtained in research setting and home using ecological momentary assessment (EMA). Methods EMA of 18 caregivers (mean age 66.4±7.8, 89% females) and 23 non-caregivers (mean age 66.4±7.9, 87% females) was implemented using a personal digital assistant. Subjects rated their perceived stress, fatigue, coping with current situation, mindfulness, and situational demand once in the research center and again at 3–4 semi-random points during a day at home. The data from several assessments conducted at home were averaged for statistical analyses and compared to the data collected in the research center. Results Testing environment had a differential effect on caregivers and non-caregivers for the ratings of perceived stress (p < 0.01) and situational demand (p = 0.01). When tested in research center, ratings for all measures were similar between groups, but when tested at home, caregivers rated their perceived stress higher than non-caregivers (p = 0.02). Overall, caregivers reported higher perceived stress at home than in the research center (p = 0.02), and non-caregivers reported greater situational demand in the research center than at home (p < 0.01). Conclusions The assessment method and environment affect stress-related outcomes. Evaluating participants in their natural environment provides a more sensitive measure of stress-related outcomes. EMA provides a convenient way to gather data when evaluating dementia caregivers. PMID:21777503

Mechanical analysis and force chain determination in granular materials using digital image correlation.

PubMed

Chen, Fanxiu; Zhuang, Qi; Zhang, Huixin

2016-06-20

The mechanical behaviors of granular materials are governed by the grain properties and microstructure of the materials. We conducted experiments to study the force transmission in granular materials using plane strain tests. The large amount of nearly continuous displacement data provided by the advanced noncontact experimental technique of digital image correlation (DIC) has provided a means to quantify local displacements and strains at the particle level. The average strain of each particle could be calculated based on the DIC method, and the average stress could be obtained using Hooke's law. The relationship between the stress and particle force could be obtained based on basic Newtonian mechanics and the balance of linear momentum at the particle level. This methodology is introduced and validated. In the testing procedure, the system is tested in real 2D particle cases, and the contact forces and force chain are obtained and analyzed. The system has great potential for analyzing a real granular system and measuring the contact forces and force chain.

Wall relaxation in growing stems: comparison of four species and assessment of measurement techniques

NASA Technical Reports Server (NTRS)

Cosgrove, D. J.

1987-01-01

This study was carried out to develop improved methods for measuring in-vivo stress relaxation of growing tissues and to compare relaxation in the stems of four different species. When water uptake by growing tissue is prevented, in-vivo stress relaxation occurs because continued wall loosening reduces wall stress and cell turgor pressure. With this procedure one may measure the yield threshold for growth (Y), the turgor pressure in excess of the yield threshold (P-Y), and the physiological wall extensibility (phi). Three relaxation techniques proved useful: "turgor-relaxation", "balance-pressure" and "pressure-block". In the turgor-relaxation method, water is withheld from growing tissue and the reduction in turgor is measured directly with the pressure probe. This technique gives absolute values for P and Y, but requires tissue excision. In the balance-pressure technique, the excised growing region is sealed in a pressure chamber, and the subsequent reduction in water potential is measured as the applied pressure needed to return xylem sap to the cut surface. This method is simple, but only measures (P-Y), not the individual values of P and Y. In the pressure-block technique, the growing tissue is sealed into a pressure chamber, growth is monitored continuously, and just sufficient pressure is applied to the chamber to block growth. The method gives high-resolution kinetics of relaxation and does not require tissue excision, but only measures (P-Y). The three methods gave similar results when applied to the growing stems of pea (Pisum sativum L.), cucumber (Cucumis sativus L.), soybean (Glycine max (L.) Merr.) and zucchini (Curcubita pepo L.) seedlings. Values for (P-Y) averaged between 1.4 and 2.7 bar, depending on species. Yield thresholds averaged between 1.3 and 3.0 bar. Compared with the other methods, relaxation by pressure-block was faster and exhibited dynamic changes in wall-yielding properties. The two pressure-chamber methods were also used to measure the internal water-potential gradient (between the xylem and the epidermis) which drives water uptake for growth. For the four species it was small, between 0.3 and 0.6 bar, and so did not limit growth substantially.

Role of stress in burnout among students of medicine and dentistry--a study in Ljubljana, Slovenia, Faculty of Medicine.

PubMed

Kogoj, Tina Krokter; Cebašek-Travnik, Zdenka; Zaletel-Kragelj, Lijana

2014-09-01

Medical education is challenging, but for some students it can be very stressful. Studies suggest that stress during medical education can have a negative impact on students' mental health and that burnout is frequent among medical school students. The aim of this study was to measure burnout among students of medicine/dentistry (M/D) at the Faculty of Medicine, University of Ljubljana, Slovenia, in relation to their perception of stress, so as to enable planning preventative activities for students at risk. The data were collected in a cross-sectional study, carried out in spring 2008 among the total population of MID students of 1St, 3rd, 4th and 6th year, using a self-administered online questionnaire. Oldenburg Burnout Inventory (OLBI) instrument was used. Separate burnout scores were calculated for the exhaustion and disengagement dimensions of burnout, and related to students'perception of stress. Multiple linear regression method was carried out to adjust the association estimates for several potential confounders (gender, study program, relationship status, and grade). The overall response rate was 47.2%, and a total of 476 students participated. Students scored higher on exhaustion than on disengagement dimension--the mean value of burnout scores on the exhaustion dimension scale was -1.68, while it was -4.58 on the disengagement dimension scale. The results showed a statistically significant difference between high and low risk-for-stress groups of students in both burnout dimensions (average value of burnout scores on the exhaustion scale: high risk-for-stress group -3.69, low risk-for-stress group 0.19, p<0.001; average value of burnout scores on the disengagement scale: high risk-for-stress group -5.57, low risk-for-stress group -3.65, p<0.001). After adjustment for potential confounders differences on both burnout subscales remained almost unchanged. Results confirmed our hypothesis that M/D students of Ljubljana Faculty of Medicine who frequently experience stress (especially those with poor coping mechanisms), exhibit higher degree of burnout.

Stress and strain distribution in three different mini dental implant designs using in implant retained overdenture: a finite element analysis study

PubMed Central

AUNMEUNGTONG, W.; KHONGKHUNTHIAN, P.; RUNGSIYAKULL, P.

2016-01-01

SUMMARY Finite Element Analysis (FEA) has been used for prediction of stress and strain between dental implant components and bone in the implant design process. Purpose Purpose of this study was to characterize and analyze stress and strain distribution occurring in bone and implants and to compare stress and strain of three different implant designs. Materials and methods Three different mini dental implant designs were included in this study: 1. a mini dental implant with an internal implant-abutment connection (MDIi); 2. a mini dental implant with an external implant-abutment connection (MDIe); 3. a single piece mini dental implant (MDIs). All implant designs were scanned using micro-CT scans. The imaging details of the implants were used to simulate models for FEA. An artificial bone volume of 9×9 mm in size was constructed and each implant was placed separately at the center of each bone model. All bone-implant models were simulatively loaded under an axial compressive force of 100 N and a 45-degree force of 100 N loading at the top of the implants using computer software to evaluate stress and strain distribution. Results There was no difference in stress or strain between the three implant designs. The stress and strain occurring in all three mini dental implant designs were mainly localized at the cortical bone around the bone-implant interface. Oblique 45° loading caused increased deformation, magnitude and distribution of stress and strain in all implant models. Conclusions Within the limits of this study, the average stress and strain in bone and implant models with MDIi were similar to those with MDIe and MDIs. The oblique 45° load played an important role in dramatically increased average stress and strain in all bone-implant models. Clinical implications Mini dental implants with external or internal connections have similar stress distribution to single piece mini dental implants. In clinical situations, the three types of mini dental implant should exhibit the same behavior to chewing force. PMID:28042449

[BURNOUT SYNDROME AND STRESS OF NURSING STAFF IN A OURENSE HOSPITAL].

PubMed

Soto-Rodríguez, Anxela; Pérez-Fernandez, Ma Reyes

2015-02-01

Set up the stress prevalence and burnout syndrome in different units of nursing staff of the Complexo Hospitalario Universitario de Ourense (CHUOU) and analyse which factors cause it. It has been designed a transversal, descriptive study by performing three assessment instruments: questionnaire of social-demographic variables; Maslach Burnout Inventory (MBI), and Nursing Stress Scale (NSS), to a 117 nursing staff of CHUOU as population. The average age was 39.23 years old and 83.8% were women. The average scoring in the emotional exhaustion dimension was 24.44, in the component of depersonalization was 7.58, and in the personal accomplishment was 34.50. Moreover, 89.7% suffer stress related with work environment. The average score in the dimension of emotional exhaustion was 24.44, the depersonalization of 7.58 and the personal accomplishment of 34.50. The 89.7% suffered from work-related stress. Nursing staff present high burnout syndrome and stress. It has been observed a higher vulnerability to the syndrome from subjects with temporary contract and rotary shift. There has been statistically significant differences in young nursing staff and less career seniority, whom present hiqher stress levels.

Aerodynamic Surface Stress Intermittency and Conditionally Averaged Turbulence Statistics

NASA Astrophysics Data System (ADS)

Anderson, W.

2015-12-01

Aeolian erosion of dry, flat, semi-arid landscapes is induced (and sustained) by kinetic energy fluxes in the aloft atmospheric surface layer. During saltation -- the mechanism responsible for surface fluxes of dust and sediment -- briefly suspended sediment grains undergo a ballistic trajectory before impacting and `splashing' smaller-diameter (dust) particles vertically. Conceptual models typically indicate that sediment flux, q (via saltation or drift), scales with imposed aerodynamic (basal) stress raised to some exponent, n, where n > 1. Since basal stress (in fully rough, inertia-dominated flows) scales with the incoming velocity squared, u^2, it follows that q ~ u^2n (where u is some relevant component of the above flow field, u(x,t)). Thus, even small (turbulent) deviations of u from its time-averaged value may play an enormously important role in aeolian activity on flat, dry landscapes. The importance of this argument is further augmented given that turbulence in the atmospheric surface layer exhibits maximum Reynolds stresses in the fluid immediately above the landscape. In order to illustrate the importance of surface stress intermittency, we have used conditional averaging predicated on aerodynamic surface stress during large-eddy simulation of atmospheric boundary layer flow over a flat landscape with momentum roughness length appropriate for the Llano Estacado in west Texas (a flat agricultural region that is notorious for dust transport). By using data from a field campaign to measure diurnal variability of aeolian activity and prevailing winds on the Llano Estacado, we have retrieved the threshold friction velocity (which can be used to compute threshold surface stress under the geostrophic balance with the Monin-Obukhov similarity theory). This averaging procedure provides an ensemble-mean visualization of flow structures responsible for erosion `events'. Preliminary evidence indicates that surface stress peaks are associated with the passage of inclined, high-momentum regions flanked by adjacent low-momentum regions. We will characterize geometric attributes of such structures and explore streamwise and vertical vorticity distribution within the conditionally averaged flow field.

Association between temperature and maternal stress during pregnancy.

PubMed

Lin, Yanfen; Hu, Wenjing; Xu, Jian; Luo, Zhongcheng; Ye, Xiaofang; Yan, Chonghuai; Liu, Zhiwei; Tong, Shilu

2017-10-01

Maternal psychological stress during pregnancy has essentially been conceptualized as a teratogen. However, little is known about the effect of temperature on maternal stress during pregnancy. The aim of this study is to investigate the relationship between temperature and maternal stress during pregnancy. In 2010, a total of 1931 eligible pregnant women were enrolled across Shanghai from four prenatal-care clinics during their mid-to-late pregnancy. Maternal life-event stress and emotional stress levels during pregnancy were assessed by the "Life Event Scale for Pregnant Women" (LESPW) and "Symptom Checklist-90-Revised Scale" (SCL-90-R), respectively. Exposure to ambient temperature was evaluated based on daily regional average in different moving average and lag days. The generalized estimating equations were used to evaluate the relationship between daily average temperature/temperature difference and maternal stress. After adjusting for relevant confounders, an U-shaped relationship was observed between daily average temperature and maternal Global-Severity-Index (GSI) of the SCL-90-R. Cumulative exposures to extremely low temperatures (< P5, 1.4-10.5℃, lag 0-1 days, 0-2 days and 0-5 days) and extremely high temperatures (≥ P95, 31.2-34.1℃, lag 0-1 days and 0-2 days), and acute exposures to extremely low (lag day 0, 1, 2 and 3) and high (lag day 0, 1) temperatures, all induced higher risks of high GSI (the highest tertile), compared to the risk induced by exposed to an optimal temperature range (20-25℃) (P< 0.05). Increased temperature difference was associated with high maternal GSI (P< 0.05). However, non-significant associations were observed between daily average temperatures/temperature differences and maternal log-transferred LESPW scores. Cumulative and acute exposures to extremely low/high temperatures may both induce emotional stress during pregnancy. Copyright © 2017 Elsevier Inc. All rights reserved.

Numerical investigation of airflow in an idealised human extra-thoracic airway: a comparison study

PubMed Central

Chen, Jie; Gutmark, Ephraim

2013-01-01

Large eddy simulation (LES) technique is employed to numerically investigate the airflow through an idealised human extra-thoracic airway under different breathing conditions, 10 l/min, 30 l/min, and 120 l/min. The computational results are compared with single and cross hot-wire measurements, and with time-averaged flow field computed by standard k-ω and k-ω-SST Reynolds averaged Navier-Stokes (RANS) models and the Lattice-Boltzmann method (LBM). The LES results are also compared to root-mean-square (RMS) flow field computed by the Reynolds stress model (RSM) and LBM. LES generally gives better prediction of the time-averaged flow field than RANS models and LBM. LES also provides better estimation of the RMS flow field than both the RSM and the LBM. PMID:23619907

Diastolic stress echocardiography detects coronary artery disease in patients with asymptomatic type II diabetes.

PubMed

Paraskevaidis, Ioannis A; Tsougos, Elias; Panou, Fotios; Dagres, Nikolaos; Karatzas, Dimitrios; Boutati, Eleni; Varounis, Christos; Kremastinos, Dimitrios Th

2010-03-01

Diabetes mellitus is considered as an equivalent of coronary artery disease (CAD). Aim of the study was to investigate whether in asymptomatic patients with type II diabetes, diastolic stress echocardiography may represent an alternative tool for the detection of CAD. The study population consisted of 105 patients with diabetes mellitus (age 61+/-9 years, 26% female, duration of diabetes 37+/-14 months). We performed an exercise stress test, followed by an echo-study and a single-positron emission tomography. Coronary angiography was performed within 1 month. Coronary angiography revealed a coronary artery stenosis of at least 70% in 72 patients (69%, CAD group), while the remaining formed the non-CAD group. Exercise induced an increase of both E/E' lateral and septal ratios as well as their average in the CAD group and on the contrary a decrease of these ratios in the non-CAD group. Receiver operating curve analysis for discrimination between patients with and without obstructive CAD showed an optimal cut-off value of -0.0708 for the exercise-induced change of E/E' average (area under curve 0.892, P<0.001). Sensitivities of scintigraphy and of diastolic stress echocardiography for detection of CAD were 75.0 and 93.1%, respectively; specificity was 78.8% for both methods. In asymptomatic patients, sensitivities of scintigraphy and diastolic stress echocardiography were 76.9 and 92.3%; specificity of both was 80%. In patients with type II diabetes, diastolic stress echocardiography, by means of E/E' ratio exercise-induced changes, can be used for the diagnosis and severity of CAD and for the detection of occult myocardial ischemia.

Effects of particle-fluid density ratio on the interactions between the turbulent channel flow and finite-size particles

NASA Astrophysics Data System (ADS)

Yu, Zhaosheng; Lin, Zhaowu; Shao, Xueming; Wang, Lian-Ping

2017-09-01

A parallel direct-forcing fictitious domain method is employed to perform fully resolved numerical simulations of turbulent channel flow laden with finite-size particles. The effects of the particle-fluid density ratio on the turbulence modulation in the channel flow are investigated at the friction Reynolds number of 180, the particle volume fraction of 0.84 % , and the particle-fluid density ratio ranging from 1 to 104.2. The results show that the variation of the flow drag with the particle-fluid density ratio is not monotonic, with a larger flow drag for the density ratio of 10.42, compared to those of unity and 104.2. A significant drag reduction by the particles is observed for large particle-fluid density ratios during the transient stage, but not at the statistically stationary stage. The intensity of particle velocity fluctuations generally decreases with increasing particle inertia, except that the particle streamwise root-mean-square velocity and streamwise-transverse velocity correlation in the near-wall region are largest at the density ratio of the order of 10. The averaged momentum equations are derived with the spatial averaging theorem and are used to analyze the mechanisms for the effects of the particles on the flow drag. The results indicate that the drag-reduction effect due to the decrease in the fluid Reynolds shear stress is counteracted by the drag-enhancement effect due to the increase in the total particle stress or the interphase drag force for the large particle-inertia case. The sum of the total Reynolds stress and particle inner stress contributions to the flow drag is largest at the density ratio of the order of 10, which is the reason for the largest flow drag at this density ratio. The interphase drag force obtained from the averaged momentum equation (the balance theory) is significantly smaller than (but agrees qualitatively with) that from the empirical drag formula based on the phase-averaged slip velocity for large density ratios. For the neutrally buoyant case, the balance theory predicts a positive interphase force on the particles arising from the negative gradient of the particle inner stress, which cannot be predicted by the drag formula based on the phase-averaged slip velocity. In addition, our results show that both particle collision and particle-turbulence interaction play roles in the formation of the inhomogeneous distribution of the particles at the density ratio of the order of 10.

Effects of particle-fluid density ratio on the interactions between the turbulent channel flow and finite-size particles.

PubMed

Yu, Zhaosheng; Lin, Zhaowu; Shao, Xueming; Wang, Lian-Ping

2017-09-01

A parallel direct-forcing fictitious domain method is employed to perform fully resolved numerical simulations of turbulent channel flow laden with finite-size particles. The effects of the particle-fluid density ratio on the turbulence modulation in the channel flow are investigated at the friction Reynolds number of 180, the particle volume fraction of 0.84%, and the particle-fluid density ratio ranging from 1 to 104.2. The results show that the variation of the flow drag with the particle-fluid density ratio is not monotonic, with a larger flow drag for the density ratio of 10.42, compared to those of unity and 104.2. A significant drag reduction by the particles is observed for large particle-fluid density ratios during the transient stage, but not at the statistically stationary stage. The intensity of particle velocity fluctuations generally decreases with increasing particle inertia, except that the particle streamwise root-mean-square velocity and streamwise-transverse velocity correlation in the near-wall region are largest at the density ratio of the order of 10. The averaged momentum equations are derived with the spatial averaging theorem and are used to analyze the mechanisms for the effects of the particles on the flow drag. The results indicate that the drag-reduction effect due to the decrease in the fluid Reynolds shear stress is counteracted by the drag-enhancement effect due to the increase in the total particle stress or the interphase drag force for the large particle-inertia case. The sum of the total Reynolds stress and particle inner stress contributions to the flow drag is largest at the density ratio of the order of 10, which is the reason for the largest flow drag at this density ratio. The interphase drag force obtained from the averaged momentum equation (the balance theory) is significantly smaller than (but agrees qualitatively with) that from the empirical drag formula based on the phase-averaged slip velocity for large density ratios. For the neutrally buoyant case, the balance theory predicts a positive interphase force on the particles arising from the negative gradient of the particle inner stress, which cannot be predicted by the drag formula based on the phase-averaged slip velocity. In addition, our results show that both particle collision and particle-turbulence interaction play roles in the formation of the inhomogeneous distribution of the particles at the density ratio of the order of 10.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tan, Yi, E-mail: tanyi@dlut.edu.cn; You, Xiaogang; You, Qifan

Electron beam smelting (EBS) has been used to fabricate the Inconel 740 superalloy. Microstructures, hardness, and deformation characteristics of the alloy are studied. It is observed that carbides and fine secondary phase nuclei are distributed in the hot worked EBS 740 superalloy. The Ostwald ripening occurs during solution treatment and leads to aggregation of the γ′ precipitates, the size of γ′ precipitates varies from several nanometers to more than one hundred nanometers as a result. The average size of the secondary phase is < 30 nm after aging treatment and the average Vickers hardness is measured to be about 370.more » The critical shear stress is calculated to be 0.627 GPa with governing mechanism of shearing, causing a stronger strengthening effect than the traditionally prepared Inconel 740 superalloy. The compression behavior indicates that the EBS 740 superalloy shows higher flow stress than 740H at low Zener-Hollomon parameter, which may arise from the undissolved γ′ precipitates and higher activation energy Q. The tensile results show that the fracture surface exhibits a ductile fracture pattern, in contrast to no obvious plastic deformation on the macroscopic fracture. Crack propagation proceeds in a transgranular fracture mode with facets and voids presented on the fracture surface. - Graphical abstract: Electron beam smelting (EBS) has been used to fabricate the Inconel 740 superalloy. Microstructures, hardness, and deformation characteristics of the alloy are studied. The average size of the secondary phase is < 30 nm after aging treatment and the average Vickers hardness is measured to be about 370. The critical shear stress is calculated to be 0.627 GPa with governing mechanism of shearing, causing a stronger strengthening effect than the traditionally prepared Inconel 740 superalloy. The EBS 740 superalloy shows higher flow stress than 740H at low Zener-Hollomon parameter, which may arise from the undissolved γ′ precipitates and higher activation energy Q. The EBS technology shows encouraging potential in preparation of nickel-based superalloys. Morphologies of γ′ precipitates and Vickers hardness as well as hot compression curves for electron beam smelting 740 superalloy. - Highlights: • Electron beam smelting, a novel method, was used to prepare the Inconel 740 superalloy. • The average size of the γ′ precipitates after aging treatment is < 30 nm. • The shearing mode generates a stronger strengthening effect than the traditional 740. • At low Zener-Hollomon parameter, the EBS 740 shows higher flow stress than 740H.« less

Evaluation of the Effect of Surface Finish on High-Cycle Fatigue for SLM-IN718

NASA Technical Reports Server (NTRS)

Lambert, Dennis M.

2016-01-01

A high-cycle fatigue (HCF) knockdown factor was estimated for Inconel 718, manufactured with the selective laser melt (SLM) process. This factor is the reduction at a common fatigue life from the maximum stress in fatigue for low-stress ground (LSG) specimens to the maximum stress of those left with the original surface condition. Various vendors provided specimens. To reduce the number of degrees-of-freedom, only one heat treat condition was evaluated. Testing temperatures included room temperature, 800F, 1000F, and 1200F. The two surface conditions were compared at constant lives, where data was available. The recommended knockdown factor of the as-built surface condition (average roughness of approximately 245 micro-inches/inch) versus low-stress ground condition (roughness <= 4 micro-inches/inch) is approximately 1/3 or 33%. This is to say that for the as-built surface condition, a maximum stress of 2/3 of the stress for LSG can be expected to produce the same life in the as built surface condition. As an alternative method, the surface finish was incorporated into a new parameter with the maximum stress. The new parameter was formulated to be similar to the fracture mechanics stress intensity factor, and it was named the pseudo stress intensity factor, Kp. Using Kp, the variance seemed acceptable across all sources, and the knockdown factor was estimated over the range of data identified by Kp where data occurred. A plot of the results suggests that the knockdown factor is a function of temperature, and that for low lives the knockdown is greater than the knockdown observed above about one million cycles, where it stabilizes. One data point at room temperature was clearly different, and the sparsity of data in the higher life region reduces the value of these results. The method does appear to provide useful results, and further characterization of the method is suggested.

The tidally averaged momentum balance in a partially and periodically stratified estuary

USGS Publications Warehouse

Stacey, M.T.; Brennan, Matthew L.; Burau, J.R.; Monismith, Stephen G.

2010-01-01

Observations of turbulent stresses and mean velocities over an entire spring-neap cycle are used to evaluate the dynamics of tidally averaged flows in a partially stratified estuarine channel. In a depth-averaged sense, the net flow in this channel is up estuary due to interaction of tidal forcing with the geometry of the larger basin. The depth-variable tidally averaged flow has the form of an estuarine exchange flow (downstream at the surface, upstream at depth) and varies in response to the neap-spring transition. The weakening of the tidally averaged exchange during the spring tides appears to be a result of decreased stratification on the tidal time scale rather than changes in bed stress. The dynamics of the estuarine exchange flow are defined by a balance between the vertical divergence of the tidally averaged turbulent stress and the tidally averaged pressure gradient in the lower water column. In the upper water column, tidal stresses are important contributors, particularly during the neap tides. The usefulness of an effective eddy viscosity in the tidally averaged momentum equation is explored, and it is seen that the effective eddy viscosity on the subtidal time scale would need to be negative to close the momentum balance. This is due to the dominant contribution of tidally varying turbulent momentum fluxes, which have no specific relation to the subtidal circulation. Using a water column model, the validity of an effective eddy viscosity is explored; for periodically stratified water columns, a negative effective viscosity is required. ?? 2010 American Meteorological Society.

Stress drop inferred from dynamic rupture simulations consistent with Moment-Rupture area empirical scaling models: Effects of week shallow zone

NASA Astrophysics Data System (ADS)

Dalguer, L. A.; Miyake, H.; Irikura, K.; Wu, H., Sr.

2016-12-01

Empirical scaling models of seismic moment and rupture area provide constraints to parameterize source parameters, such as stress drop, for numerical simulations of ground motion. There are several scaling models published in the literature. The effect of the finite width seismogenic zone and the free-surface have been attributed to cause the breaking of the well know self-similar scaling (e.g. Dalguer et al, 2008) given origin to the so called L and W models for large faults. These models imply the existence of three-stage scaling relationship between seismic moment and rupture area (e.g. Irikura and Miyake, 2011). In this paper we extend the work done by Dalguer et al 2008, in which these authors calibrated fault models that match the observations showing that the average stress drop is independent of earthquake size for buried earthquakes, but scale dependent for surface-rupturing earthquakes. Here we have developed additional sets of dynamic rupture models for vertical strike slip faults to evaluate the effect of the weak shallow layer (WSL) zone for the calibration of stress drop. Rupture in the WSL zone is expected to operate with enhanced energy absorption mechanism. The set of dynamic models consists of fault models with width 20km and fault length L=20km, 40km, 60km, 80km, 100km, 120km, 200km, 300km and 400km and average stress drop values of 2.0MPa, 2.5MPa, 3.0MPa, 3.5MPa, 5.0MPa and 7.5MPa. For models that break the free-surface, the WSL zone is modeled assuming a 2km width with stress drop 0.0MPa or -2.0 MPa. Our results show that depending on the characterization of the WSL zone, the average stress drop at the seismogenic zone that fit the empirical models changes. If WSL zone is not considered, that is, stress drop at SL zone is the same as the seismogenic zone, average stress drop is about 20% smaller than models with WSL zone. By introducing more energy absorption at the SL zone, that could be the case of large mature faults, the average stress drop in the seismogenic zone increases. Suggesting that large earthquakes need higher stress drop to break the fault than buried and moderate earthquakes. Therefore, the value of the average stress drop for large events that break the free-source depend on the definition of the WSL. Suggesting that the WSL plays an important role on the prediction of final slip and fault displacement.

Texture analysis at neutron diffractometer STRESS-SPEC

NASA Astrophysics Data System (ADS)

Brokmeier, H.-G.; Gan, W. M.; Randau, C.; Völler, M.; Rebelo-Kornmeier, J.; Hofmann, M.

2011-06-01

In response to the development of new materials and the application of materials and components in advanced technologies, non-destructive measurement methods of textures and residual stresses have gained worldwide significance in recent years. The materials science neutron diffractometer STRESS-SPEC at FRM II (Garching, Germany) is designed to be applied equally to texture and residual stress analyses by virtue of its very flexible configuration. Due to the high penetration capabilities of neutrons and the high neutron flux of STRESS-SPEC it allows a combined analysis of global texture, local texture, strain pole figure and FWHM pole figure in a wide variety of materials including metals, alloys, composites, ceramics and geological materials. Especially, the analysis of texture gradients in bulk materials using neutron diffraction has advantages over laboratory X-rays and EBSD for many scientific cases. Moreover, neutron diffraction is favourable for coarse-grained materials, where bulk information averaged over texture inhomogeneities is needed, and also stands out due to easy sample preparation. In future, the newly developed robot system for STRESS-SPEC will allow much more flexibility than an Eulerian cradle as on standard instruments. Five recent measurements are shown to demonstrate the wide range of possible texture applications at STRESS-SPEC diffractometer.

Stress and Schooling: A Search for Stress Profiles of Adolescent Students.

ERIC Educational Resources Information Center

Thomas, Elwyn

This study examined how a sample of pre-university Singaporean adolescents (N=212) with an average age of 17 years 5 months attending a variety of junior colleges perceived and managed different sources of stress. Measures of stress included Behavior Profile, Life Events, School Stress Factors, Home-School Stress Conditions and Stress Symptoms.…

Electric pulses used in electrochemotherapy and electrogene therapy do not significantly change the expression profile of genes involved in the development of cancer in malignant melanoma cells

PubMed Central

2009-01-01

Background Electroporation is a versatile method for in vitro or in vivo delivery of different molecules into cells. However, no study so far has analysed the effects of electric pulses used in electrochemotherapy (ECT pulses) or electric pulses used in electrogene therapy (EGT pulses) on malignant cells. We studied the effect of ECT and EGT pulses on human malignant melanoma cells in vitro in order to understand and predict the possible effect of electric pulses on gene expression and their possible effect on cell behaviour. Methods We used microarrays with 2698 different oligonucleotides to obtain the expression profile of genes involved in apoptosis and cancer development in a malignant melanoma cell line (SK-MEL28) exposed to ECT pulses and EGT pulses. Results Cells exposed to ECT pulses showed a 68.8% average survival rate, while cells exposed to EGT pulses showed a 31.4% average survival rate. Only seven common genes were found differentially expressed in cells 16 h after exposure to ECT and EGT pulses. We found that ECT and EGT pulses induce an HSP70 stress response mechanism, repress histone protein H4, a major protein involved in chromatin assembly, and down-regulate components involved in protein synthesis. Conclusion Our results show that electroporation does not significantly change the expression profile of major tumour suppressor genes or oncogenes of the cell cycle. Moreover, electroporation also does not changes the expression of genes involved in the stability of DNA, supporting current evidence that electroporation is a safe method that does not promote tumorigenesis. However, in spite of being considered an isothermal method, it does to some extent induce stress, which resulted in the expression of the environmental stress response mechanism, HSP70. PMID:19709437

High performance lignin-acrylonitrile polymer blend materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Naskar, Amit K.; Tran, Chau D.

A polymer blend material comprising: (i) a lignin component having a weight-average molecular weight of up to 1,000,000 g/mol; and (ii) an acrylonitrile-containing copolymer rubber component comprising acrylonitrile units in combination with diene monomer units, and having an acrylonitrile content of at least 20 mol %; wherein said lignin component is present in an amount of at least 5 wt % and up to about 95 wt % by total weight of components (i) and (ii); and said polymer blend material possesses a tensile yield stress of at least 5 MPa, or a tensile stress of at least 5 MPamore » at 10% elongation, or a tensile stress of at least 5 MPa at 100% elongation. Methods for producing the polymer blend, molded forms thereof, and articles thereof, are also described.« less

Hydromagnetic couple-stress nanofluid flow over a moving convective wall: OHAM analysis

NASA Astrophysics Data System (ADS)

Awais, M.; Saleem, S.; Hayat, T.; Irum, S.

2016-12-01

This communication presents the magnetohydrodynamics (MHD) flow of a couple-stress nanofluid over a convective moving wall. The flow dynamics are analyzed in the boundary layer region. Convective cooling phenomenon combined with thermophoresis and Brownian motion effects has been discussed. Similarity transforms are utilized to convert the system of partial differential equations into coupled non-linear ordinary differential equation. Optimal homotopy analysis method (OHAM) is utilized and the concept of minimization is employed by defining the average squared residual errors. Effects of couple-stress parameter, convective cooling process parameter and energy enhancement parameters are displayed via graphs and discussed in detail. Various tables are also constructed to present the error analysis and a comparison of obtained results with the already published data. Stream lines are plotted showing a difference of Newtonian fluid model and couplestress fluid model.

Advanced High Cycle Fatigue (HCF) Life Assurance Methodologies

DTIC Science & Technology

2004-07-01

Fatigue in 2024 - T351 Aluminum Alloy , Wear, 221(1), pp 24-36 (1998) 27. Doner, M., Bain, K.R., and Adams, J.H... alloy , PWA 1484, where temperature and orientation effects both have to be taken into account. Both fracture mechanics and fatigue life methods... effect on predicted fatigue life . On average, the fatigue life is several orders of magnitude less when residual stresses are included. The

Novel Gyroscopic Mounting for Crystal Oscillators to Increase Short and Medium Term Stability under Highly Dynamic Conditions.

PubMed

Abedi, Maryam; Jin, Tian; Sun, Kewen

2015-06-17

In this paper, a gyroscopic mounting method for crystal oscillators to reduce the impact of dynamic loads on their output stability has been proposed. In order to prove the efficiency of this mounting approach, each dynamic load-induced instability has been analyzed in detail. A statistical study has been performed on the elevation angle of the g-sensitivity vector of Stress Compensated-cut (SC-cut) crystals. The analysis results show that the proposed gyroscopic mounting method gives good performance for host vehicle attitude changes. A phase noise improvement of 27 dB maximum and 5.7 dB on average can be achieved in the case of steady state loads, while under sinusoidal vibration conditions, the maximum and average phase noise improvement are as high as 24 dB and 7.5 dB respectively. With this gyroscopic mounting method, random vibration-induced phase noise instability is reduced 30 dB maximum and 8.7 dB on average. Good effects are apparent for crystal g-sensitivity vectors with low elevation angle φ and azimuthal angle β. under highly dynamic conditions, indicating the probability that crystal oscillator instability will be significantly reduced by using the proposed mounting approach.

Shear viscosity of a two-dimensional emulsion of drops using a multiple-relaxation-time-step lattice Boltzmann method

NASA Astrophysics Data System (ADS)

Halliday, I.; Xu, X.; Burgin, K.

2017-02-01

An extended Benzi-Dellar lattice Boltzmann equation scheme [R. Benzi, S. Succi, and M. Vergassola, Europhys. Lett. 13, 727 (1990), 10.1209/0295-5075/13/8/010; R. Benzi, S. Succi, and M. Vergassola, Phys. Rep. 222, 145 (1992), 10.1016/0370-1573(92)90090-M; P. J. Dellar, Phys. Rev. E 65, 036309 (2002), 10.1103/PhysRevE.65.036309] is developed and applied to the problem of confirming, at low Re and drop fluid concentration, c , the variation of effective shear viscosity, ηeff=η1[1 +f (η1,η2) c ] , with respect to c for a sheared, two-dimensional, initially crystalline emulsion [here η1 (η2) is the fluid (drop fluid) shear viscosity]. Data obtained with our enhanced multicomponent lattice Boltzmann method, using average shear stress and hydrodynamic dissipation, agree well once appropriate corrections to Landau's volume average shear stress [L. Landau and E. M. Lifshitz, Fluid Mechanics, 6th ed. (Pergamon, London, 1966)] are applied. Simulation results also confirm the expected form for f (ηi,η2) , and they provide a reasonable estimate of its parameters. Most significantly, perhaps, the generality of our data supports the validity of Taylor's disputed simplification [G. I. Taylor, Proc. R. Soc. London, Ser. A 138, 133 (1932), 10.1098/rspa.1932.0175] to reduce the effect of one hydrodynamic boundary condition (on the continuity of the normal contraction of stress) to an assumption that interfacial tension is sufficiently strong to maintain a spherical drop shape.

Reduction in the cumulative effect of stress-induced inbreeding depression due to intragenerational purging in Drosophila melanogaster.

PubMed

Enders, L S; Nunney, L

2016-03-01

Environmental stress generally exacerbates the harmful effects of inbreeding and it has been proposed that this could be exploited in purging deleterious alleles from threatened inbred populations. However, understanding what factors contribute to variability in the strength of inbreeding depression (ID) observed across adverse environmental conditions remains a challenge. Here, we examined how the nature and timing of stress affects ID and the potential for purging using inbred and outbred Drosophila melanogaster larvae exposed to biotic (larval competition, bacteria infection) and abiotic (ethanol, heat) stressors compared with unstressed controls. ID was measured during (larval survival) and after (male mating success) stress exposure. The level of stress imposed by each stressor was approximately equal, averaging a 42% reduction in outbred larval survival relative to controls. All stressors induced on average the same ID, causing a threefold increase in lethal equivalents for larval survival relative to controls. However, stress-induced ID in larval success was followed by a 30% reduction in ID in mating success of surviving males. We propose that this fitness recovery is due to 'intragenerational purging' whereby fitness correlations facilitate stress-induced purging that increases the average fitness of survivors in later life history stages. For biotic stressors, post-stress reductions in ID are consistent with intragenerational purging, whereas for abiotic stressors, there appeared to be an interaction between purging and stress-induced physiological damage. For all stressors, there was no net effect of stress on lifetime ID compared with unstressed controls, undermining the prediction that stress enhances the effectiveness of population-level purging across generations.

Reduction in the cumulative effect of stress-induced inbreeding depression due to intragenerational purging in Drosophila melanogaster

PubMed Central

Enders, L S; Nunney, L

2016-01-01

Environmental stress generally exacerbates the harmful effects of inbreeding and it has been proposed that this could be exploited in purging deleterious alleles from threatened inbred populations. However, understanding what factors contribute to variability in the strength of inbreeding depression (ID) observed across adverse environmental conditions remains a challenge. Here, we examined how the nature and timing of stress affects ID and the potential for purging using inbred and outbred Drosophila melanogaster larvae exposed to biotic (larval competition, bacteria infection) and abiotic (ethanol, heat) stressors compared with unstressed controls. ID was measured during (larval survival) and after (male mating success) stress exposure. The level of stress imposed by each stressor was approximately equal, averaging a 42% reduction in outbred larval survival relative to controls. All stressors induced on average the same ID, causing a threefold increase in lethal equivalents for larval survival relative to controls. However, stress-induced ID in larval success was followed by a 30% reduction in ID in mating success of surviving males. We propose that this fitness recovery is due to ‘intragenerational purging' whereby fitness correlations facilitate stress-induced purging that increases the average fitness of survivors in later life history stages. For biotic stressors, post-stress reductions in ID are consistent with intragenerational purging, whereas for abiotic stressors, there appeared to be an interaction between purging and stress-induced physiological damage. For all stressors, there was no net effect of stress on lifetime ID compared with unstressed controls, undermining the prediction that stress enhances the effectiveness of population-level purging across generations. PMID:26604190

Determination of Residual Stress Distributions in Polycrystalline Alumina using Fluorescence Microscopy

PubMed Central

Michaels, Chris A.; Cook, Robert F.

2016-01-01

Maps of residual stress distributions arising from anisotropic thermal expansion effects in a polycrystalline alumina are generated using fluorescence microscopy. The shifts of both the R1 and R2 ruby fluorescence lines of Cr in alumina are used to create maps with sub-µm resolution of either the local mean and shear stresses or local crystallographic a- and c-stresses in the material, with approximately ± 1 MPa stress resolution. The use of single crystal control materials and explicit correction for temperature and composition effects on line shifts enabled determination of the absolute values and distributions of values of stresses. Temperature correction is shown to be critical in absolute stress determination. Experimental determinations of average stress parameters in the mapped structure are consistent with assumed equilibrium conditions and with integrated large-area measurements. Average crystallographic stresses of order hundreds of MPa are determined with characteristic distribution widths of tens of MPa. The stress distributions reflect contributions from individual clusters of stress in the structure; the cluster size is somewhat larger than the grain size. An example application of the use of stress maps is shown in the calculation of stress-intensity factors for fracture in the residual stress field. PMID:27563163

The natural history of the anterior knee instability by stress radiography

PubMed Central

de Rezende, Márcia Uchôa; Hernandez, Arnaldo José; Camanho, Gilberto Luis

2014-01-01

OBJECTIVE: To analyze the anteroposterior displacement of the knee by means of stress radiography in individuals with unilateral anterior knee instability and relate to time of instability. METHODS: Sixty individuals with intact knees (control group) and 125 patients with unilateral anterior instability (AI group) agreed to participate in the study. Gender, age, weight, height, age at injury, time between injury and testing, and surgical findings are studied. Both groups are submitted to anterior and posterior stress radiographies of both knees. Anterior (ADD) and posterior displacement difference (PDD) were calculated between sides. RESULTS: In the control group ADD and PDD are in average, zero, whereas in the AI group ADD averaged 9.8mm and PDD, 1.92mm. Gender, age, weight, height, age at trauma and presence of menisci's lesions do not intervene in the values of ADD and PDD. Meniscal injuries increase with time. ADD and PDD do not relate with the presence or absence of associated menisci's lesions. The ADD and the PDD are related to each other and increase with time. CONCLUSION: There is a permanent anterior subluxation of the injured knee that is related to the amount of anterior displacement that increases with time. Level of Evidence III, Study Types Case-control study. PMID:25246846

Paternal and maternal concerns for their very low-birth-weight infants transitioning from the NICU to home.

PubMed

Garfield, Craig F; Lee, Young; Kim, Hyung Nam

2014-01-01

This study examines qualitatively the concerns and coping mechanisms of fathers and mothers of very low-birth-weight (VLBW; <1500 g) neonatal intensive care unit (NICU) infants as they transition to home from the NICU. In-depth, semistructured phone interviews were conducted with a sample of fathers and mothers of VLBW NICU infants in the Chicago area who had transitioned home, and parental concerns were examined during the transition to home. Phone interviews lasting 30 to 60 minutes were transcribed verbatim, and all interviews were coded using content and narrative analysis. Twenty-five parents (10 fathers, 15 mothers) of 16 VLBW infants who had an average gestational age of 29.5 weeks and an average NICU stay of 58.38 days completed the interview. Overriding concerns included pervasive uncertainty, lingering medical concerns, and partner-related adjustment concerns that differed by gender. A variety of resilient coping methods during this stressful transition are also described. Fathers and mothers of VLBW NICU graduates have evolving but often differing concerns as they transition from the NICU to home. Many of these concerns can be addressed with improved discharge information exchanges and anticipatory guidance. Supporting parents during this stressful and often difficult transition may lead to decreased family stress, improved care, and better infant outcomes.

Daily Stressor Reactivity during Adolescence: The Buffering Role of Parental Warmth

PubMed Central

Lippold, Melissa; Davis, Kelly D.; McHale, Susan M.; Buxton, Orfeu; Almeida, David M.

2016-01-01

Objective This study examined youth stressor reactivity in the form of links between daily stressors and adolescents’ negative affect, physical health symptoms, and cortisol patterns. We also tested whether youth gender and parental warmth moderated these linkages. Method Participants were the children of employees in the Information Technology division of a large company (N = 132, mean age = 13.39 years, 55% female). Youth completed daily diary telephone interviews on 8 consecutive evenings and provided saliva samples at 4 time points over 4 days to assess daily stressors and youth physiological and affective functioning. Parental warmth was assessed during in-home interviews. Multi-level modeling was used to account for interdependencies in the data. Results Youth who experienced more daily stressors, on average, reported more negative affect and physical health symptoms, on average. Further, on days youth reported more stressors than usual (compared to their own across-day average), they also exhibited more physical health symptoms, reduced evening cortisol decline (e.g., flatter slopes), higher bedtime cortisol, and more negative affect. Girls had stronger within-person linkages between daily stressors and daily negative affect than boys. Parental warmth moderated these within-person linkages: Youth who experienced more parental warmth had lower negative affect and steeper cortisol decline than usual on less stressful days. Yet, youth who experienced less parental warmth had higher negative affect and their cortisol levels declined less, even on days with lower-than-usual stress. Conclusions Daily stressors are associated with youth's affective and physiological functioning, but parental warmth can support youth's stress recovery. PMID:27175577

New concept for treating female stress urinary incontinence with radiofrequency

PubMed Central

Lordelo, Patrícia; Boas, Andrea Vilas; Sodré, Danielle; Lemos, Amanda; Tozetto, Sibele; Brasil, Cristina

2017-01-01

ABSTRACT Purpose: To evaluate the clinical response and adverse effects of radiofrequency on the urethral meatus in the treatment of stress urinary incontinence in women. Materials and Methods: This phase one study included ten women with Stress Urinary Incontinence (SUI). The evaluation consisted of 1 hour Pad tests to quantify urine loss and to assess the degree of procedure satisfaction by using the Likert scale. To evaluate safety, we observed the number of referred side effects. Results: Average age was 53.10 years±7.08 years. In assessing the final Pad Test, 70% showed a reduction and 30% a worsening of urinary loss. Using the Pad Test one month later, there was a reduction in all patients (p=0.028). The degree of satisfaction was 90% and no side effects have been observed. One patient reported burning sensation. Conclusion: The treatment of SUI with radiofrequency on the urethral meatus has no adverse effects, being a low risk method that reduces urinary loss in women. However, to increase the validity of the study, larger clinical trials are warranted. PMID:28727373

A real-time assessment of work stress in physicians and nurses.

PubMed

Rutledge, Thomas; Stucky, Erin; Dollarhide, Adrian; Shively, Martha; Jain, Sonia; Wolfson, Tanya; Weinger, Matthew B; Dresselhaus, Timothy

2009-03-01

This study adapted ecological momentary assessment methods to: (a) examine differences in work stress between nurses and physicians, and (b) to study relationships between work stress, work activity patterns, and sleep. A total of 185 physicians and 119 nurses (206 women, 98 men) working in four teaching hospitals participated in an observational study of work stress. Participants carried handheld computers that randomly prompted them for work activity, patient load, and work stress information. Participants completed more than 9,500 random interval surveys during the study (an average of 30.8 surveys per person-week). Approximately 85% of all surveys were completed in full (73.3%) or partially (11.6%). Emotional stress scores among physicians were nearly 50% higher (26.9[19.0]) than those of nurses (18.1[14.9], r[302] = .37, p < .001). Direct and indirect care activities were associated with higher stress reports by both clinician groups (rs[159] = .14-.26, ps < .01). Sleep quality and quantity were predictors of work stress scores (ps < .05). Finally, higher work stress and lower sleep quality were also associated with poorer memory performance (r[302] = -.12, .17, ps < 05). The findings identify patterns of work stress in relationship to work activities, sleep habits, and provider differences that may be used to assist ongoing hospital work reform efforts. (c) 2009 APA, all rights reserved

Determining Individual Phase Properties in a Multi-phase Q&P Steel using Multi-scale Indentation Tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cheng, Guang; Choi, Kyoo Sil; Hu, Xiaohua

2016-01-15

A new inverse method was developed to predict the stress-strain behaviors of constituent phases in a multi-phase steel using the load-depth curves measured in nanoindentation tests combined with microhardness measurements. A power law hardening response was assumed for each phase, and an empirical relationship between hardness and yield strength was assumed. Adjustment was made to eliminate the indentation size effect and indenter bluntness effect. With the newly developed inverse method and statistical analysis of the hardness histogram for each phase, the average stress-strain curves of individual phases in a quench and partitioning (Q&P) steel, including austenite, tempered martensite and untemperedmore » martensite, were calculated and the results were compared with the phase properties obtained by in-situ high energy X-ray diffraction (HEXRD) test. It is demonstrated that multi-scale instrumented indentation tests together with the new inverse method are capable of determining the individual phase flow properties in multi-phase alloys.« less

Sleep quantity, quality, and insomnia symptoms of medical students during clinical years. Relationship with stress and academic performance.

PubMed

Alsaggaf, Mohammed A; Wali, Siraj O; Merdad, Roah A; Merdad, Leena A

2016-02-01

To determine sleep habits and sleep quality in medical students during their clinical years using validated measures; and to investigate associations with academic performance and psychological stress. In this cross-sectional study, medical students (n=320) were randomly selected from a list of all enrolled clinical-year students in a Saudi medical school from 2011-2012. Students filled a questionnaire including demographic and lifestyle factors, Pittsburgh Sleep Quality Index, Epworth Sleepiness Scale, and Perceived Stress Scale. Students acquired on average, 5.8 hours of sleep each night, with an average bedtime at 01:53. Approximately 8% reported acquiring sleep during the day, and not during nighttime. Poor sleep quality was present in 30%, excessive daytime sleepiness (EDS) in 40%, and insomnia symptoms in 33% of students. Multivariable regression models revealed significant associations between stress, poor sleep quality, and EDS. Poorer academic performance and stress were associated with symptoms of insomnia. Sleep deprivation, poor sleep quality, and EDS are common among clinical years medical students. High levels of stress and the pressure of maintaining grade point averages may be influencing their quality of sleep.

Estimation of dislocations density and distribution of dislocations during ECAP-Conform process

NASA Astrophysics Data System (ADS)

Derakhshan, Jaber Fakhimi; Parsa, Mohammad Habibi; Ayati, Vahid; Jafarian, Hamidreza

2018-01-01

Dislocation density of coarse grain aluminum AA1100 alloy (140 µm) that was severely deformed by Equal Channel Angular Pressing-Conform (ECAP-Conform) are studied at various stages of the process by electron backscattering diffraction (EBSD) method. The geometrically necessary dislocations (GNDs) density and statistically stored dislocations (SSDs) densities were estimate. Then the total dislocations densities are calculated and the dislocation distributions are presented as the contour maps. Estimated average dislocations density for annealed of about 2×1012 m-2 increases to 4×1013 m-2 at the middle of the groove (135° from the entrance), and they reach to 6.4×1013 m-2 at the end of groove just before ECAP region. Calculated average dislocations density for one pass severely deformed Al sample reached to 6.2×1014 m-2. At micrometer scale the behavior of metals especially mechanical properties largely depend on the dislocation density and dislocation distribution. So, yield stresses at different conditions were estimated based on the calculated dislocation densities. Then estimated yield stresses were compared with experimental results and good agreements were found. Although grain size of material did not clearly change, yield stress shown intensive increase due to the development of cell structure. A considerable increase in dislocations density in this process is a good justification for forming subgrains and cell structures during process which it can be reason of increasing in yield stress.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jones, David R.; Morrow, Benjamin M.; Trujillo, Carl P.

Here, we present a series of experiments probing the martensitic α–ω (hexagonal close-packed to simple hexagonal) transition in titanium under shock-loading to peak stresses around 15 GPa. Gas-gun plate impact techniques were used to locate the α–ω transition stress with a laser-based velocimetry diagnostic. A change in the shock-wave profile at 10.1 GPa suggests the transition begins at this stress. A second experiment shock-loaded and then soft-recovered a similar titanium sample. We then analyzed this recovered material with electron-backscatter diffraction methods, revealing on average approximately 65% retained ω phase. Furthermore, based on careful analysis of the microstructure, we propose thatmore » the titanium never reached a full ω state, and that there was no observed phase-reversion from ω to α. Texture analysis suggests that any α titanium found in the recovered sample is the original α. The data show that both the α and ω phases are stable and can coexist even though the shock-wave presents as steady-state, at these stresses.« less

Post-traumatic stress symptoms and structure among orphan and vulnerable children and adolescents in Zambia

PubMed Central

Familiar, Itziar; Murray, Laura; Gross, Alden; Skavenski, Stephanie; Jere, Elizabeth; Bass, Judith

2014-01-01

Background Scant information exists on PTSD symptoms and structure in youth from developing countries. Methods We describe the symptom profile and exposure to trauma experiences among 343 orphan and vulnerable children and adolescents from Zambia. We distinguished profiles of post-traumatic stress symptoms using latent class analysis. Results Average number of trauma-related symptoms (21.6; range 0-38) was similar across sex and age. Latent class model suggested 3 classes varying by level of severity: low (31% of the sample), medium (45% of the sample), and high (24% of the sample) symptomatology. Conclusions Results suggest that PTSD is a continuously distributed latent trait. PMID:25382359

Propagation of elastic wave in nanoporous material with distributed cylindrical nanoholes

NASA Astrophysics Data System (ADS)

Qiang, FangWei; Wei, PeiJun; Liu, XiQiang

2013-08-01

The effective propagation constants of plane longitudinal and shear waves in nanoporous material with random distributed parallel cylindrical nanoholes are studied. The surface elastic theory is used to consider the surface stress effects and to derive the nontraditional boundary condition on the surface of nanoholes. The plane wave expansion method is used to obtain the scattering waves from the single nanohole. The multiple scattering effects are taken into consideration by summing the scattered waves from all scatterers and performing the configuration averaging of random distributed scatterers. The effective propagation constants of coherent waves along with the associated dynamic effective elastic modulus are numerically evaluated. The influences of surface stress are discussed based on the numerical results.

Microstructural evaluation of cumulative fatigue damage below the fatigue limit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fukuoka, C.; Nakagawa, Y.G.

1996-05-01

The objective of this work is to evaluate the microstructural changes induced near and below the fatigue limit in a pressure vessel steel plate, SA508. Dislocation cell to cell misorientation differences, {theta}, which increase with fatigue damage accumulation, are measured by the Selected Area Diffraction (SAD) method. The misorientation difference, {theta}, of the sample failed just above the fatigue limit is about 4.0 degrees on the average, which is about the same as that for the failure conditions of low cycle fatigue at higher stresses. The {theta} value increases even below the fatigue limit, but it does not increase atmore » stresses which are lower than 50% of the fatigue limit.« less

[Influence of trabecular microstructure modeling on finite element analysis of dental implant].

PubMed

Shen, M J; Wang, G G; Zhu, X H; Ding, X

2016-09-01

To analyze the influence of trabecular microstructure modeling on the biomechanical distribution of implant-bone interface with a three-dimensional finite element mandible model of trabecular structure. Dental implants were embeded in the mandibles of a beagle dog. After three months of the implant installation, the mandibles with dental implants were harvested and scaned by micro-CT and cone-beam CT. Two three-dimensional finite element mandible models, trabecular microstructure(precise model) and macrostructure(simplified model), were built. The values of stress and strain of implant-bone interface were calculated using the software of Ansys 14.0. Compared with the simplified model, the precise models' average values of the implant bone interface stress increased obviously and its maximum values did not change greatly. The maximum values of quivalent stress of the precise models were 80% and 110% of the simplified model and the average values were 170% and 290% of simplified model. The maximum and average values of equivalent strain of precise models were obviously decreased, and the maximum values of the equivalent effect strain were 17% and 26% of simplified model and the average ones were 21% and 16% of simplified model respectively. Stress and strain concentrations at implant-bone interface were obvious in the simplified model. However, the distributions of stress and strain were uniform in the precise model. The precise model has significant effect on the distribution of stress and strain at implant-bone interface.

Marginal fit and photoelastic stress analysis of CAD-CAM and overcast 3-unit implant-supported frameworks.

PubMed

Presotto, Anna Gabriella Camacho; Bhering, Cláudia Lopes Brilhante; Mesquita, Marcelo Ferraz; Barão, Valentim Adelino Ricardo

2017-03-01

Several studies have shown the superiority of computer-assisted design and computer-assisted manufacturing (CAD-CAM) technology compared with conventional casting. However, an advanced technology exists for casting procedures (the overcasting technique), which may serve as an acceptable and affordable alternative to CAD-CAM technology for fabricating 3-unit implant-supported fixed dental prostheses (FDPs). The purpose of this in vitro study was to evaluate, using quantitative photoelastic analysis, the effect of the prosthetic framework fabrication method (CAD-CAM and overcasting) on the marginal fit and stress transmitted to implants. The correlation between marginal fit and stress was also investigated. Three-unit implant-supported FDP frameworks were made using the CAD-CAM (n=10) and overcasting (n=10) methods. The frameworks were waxed to simulate a mandibular first premolar (PM region) to first molar (M region) FDP using overcast mini-abutment cylinders. The wax patterns were overcast (overcast experimental group) or scanned to obtain the frameworks (CAD-CAM control group). All frameworks were fabricated from cobalt-chromium (CoCr) alloy. The marginal fit was analyzed according to the single-screw test protocol, obtaining an average value for each region (M and PM) and each framework. The frameworks were tightened for the photoelastic model with standardized 10-Ncm torque. Stress was measured by quantitative photoelastic analysis. The results were submitted to the Student t test, 2-way ANOVA, and Pearson correlation test (α=.05). The framework fabrication method (FM) and evaluation site (ES; M and PM regions) did not affect the marginal fit values (P=.559 for FM and P=.065 for ES) and stress (P=.685 for FM and P=.468 for ES) in the implant-supported system. Positive correlations between marginal fit and stress were observed (CAD-CAM: r=0.922; P<.001; overcast: r=0.908; P<.001). CAD-CAM and overcasting methods present similar marginal fit and stress values for 3-unit FDP frameworks. The decreased marginal fit of frameworks induces greater stress in the implant-supported system. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Perceived Stress in Patients with Common Gastrointestinal Disorders: Associations with Quality of Life, Symptoms and Disease Management.

PubMed

Edman, Joel S; Greeson, Jeffrey M; Roberts, Rhonda S; Kaufman, Adam B; Abrams, Donald I; Dolor, Rowena J; Wolever, Ruth Q

Research supports relationships between stress and gastrointestinal (GI) symptoms and disorders. This pilot study assesses relationships between perceived stress, quality of life (QOL), and self-reported pain ratings as an indicator of symptom management in patients who self-reported gastroesophageal reflux disease (GERD), irritable bowel syndrome (IBS), and inflammatory bowel disease (IBD). In the full sample (n = 402) perceived stress positively correlated with depression (r = 0.76, P < .0001), fatigue (r = 0.38, P < .0001), sleep disturbance (r = 0.40, P < .0001), average pain (r = 0.26, P < .0001), and worst pain (r = 0.25, P < .0001). Higher perceived stress also correlated with lower mental health-related QOL. Similar correlations were found for the participants with GERD (n = 188), IBS (n = 132), and IBD (n = 82). Finally, there were significant correlations in the GERD cohort between perceived stress, and average pain (r = 0.34, P < .0001) and worst pain (r = 0.29, P < .0001), and in the IBD cohort between perceived stress, and average pain (r = 0.32, P < .0001), and worst pain (r = 0.35, P < .01). Perceived stress broadly correlated with QOL characteristics in patients with GERD, IBS, and IBD, and their overall QOL was significantly lower than the general population. Perceived stress also appeared to be an indicator of symptom management (self-reported pain ratings) in GERD and IBD, but not IBS. While future research using objective measures of stress and symptom/disease management is needed to confirm these associations, as well as to evaluate the ability of stress reduction interventions to improve perceived stress, QOL and disease management in these GI disorders, integrative medicine treatment programs would be most beneficial to study. Copyright © 2017 Elsevier Inc. All rights reserved.

Quantifying Grain Level Stress-Strain Behavior for AM40 via Instrumented Microindentation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cheng, Guang; Barker, Erin I.; Stephens, Elizabeth V.

2016-01-01

ABSTRACT Microindentation is performed on hot isostatic pressed (HIP) Mg-Al (AM40) alloy samples produced by high-pressure die cast (HPDC) process for the purpose of quantifying the mechanical properties of the α-Mg grains. The process of obtaining elastic modulus and hardness from indentation load-depth curves is well established in the literature. A new inverse method is developed to extract plastic properties in this study. The method utilizes empirical yield strength-hardness relationship reported in the literature together with finite element modeling of the individual indentation. Due to the shallow depth of the indentation, indentation size effect (ISE) is taken into account whenmore » determining plastic properties. The stress versus strain behavior is determined for a series of indents. The resulting average values and standard deviations are obtained for future use as input distributions for microstructure-based property prediction of AM40.« less

Stress Management Apps With Regard to Emotion-Focused Coping and Behavior Change Techniques: A Content Analysis

PubMed Central

Hoffmann, Alexandra; Bleser, Gabriele

2017-01-01

Background Chronic stress has been shown to be associated with disease. This link is not only direct but also indirect through harmful health behavior such as smoking or changing eating habits. The recent mHealth trend offers a new and promising approach to support the adoption and maintenance of appropriate stress management techniques. However, only few studies have dealt with the inclusion of evidence-based content within stress management apps for mobile phones. Objective The aim of this study was to evaluate stress management apps on the basis of a new taxonomy of effective emotion-focused stress management techniques and an established taxonomy of behavior change techniques. Methods Two trained and independent raters evaluated 62 free apps found in Google Play with regard to 26 behavior change and 15 emotion-focused stress management techniques in October 2015. Results The apps included an average of 4.3 behavior change techniques (SD 4.2) and 2.8 emotion-focused stress management techniques (SD 2.6). The behavior change technique score and stress management technique score were highly correlated (r=.82, P=.01). Conclusions The broad variation of different stress management strategies found in this sample of apps goes in line with those found in conventional stress management interventions and self-help literature. Moreover, this study provided a first step toward more detailed and standardized taxonomies, which can be used to investigate evidence-based content in stress management interventions and enable greater comparability between different intervention types. PMID:28232299

Comparison of treadmill exercise stress cardiac MRI to stress echocardiography in healthy volunteers for adequacy of left ventricular endocardial wall visualization: A pilot study

PubMed Central

Thavendiranathan, Paaladinesh; Dickerson, Jennifer A.; Scandling, Debbie; Balasubramanian, Vijay; Pennell, Michael L.; Hinton, Alice; Raman, Subha V.; Simonetti, Orlando P.

2013-01-01

Purpose To compare exercise stress cardiac magnetic resonance (cardiac MR) to echocardiography in healthy volunteers with respect to adequacy of endocardial visualization and confidence of stress study interpretation. Materials and Methods 28 healthy volunteers (aged 28 ± 11 years, 15 males) underwent exercise stress echo and cardiac MR one week apart assigned randomly to one test first. Stress cardiac MR was performed using an MRI-compatible treadmill; stress echo was performed as per routine protocol. Cardiac MR and echo images were independently reviewed and scored for adequacy of endocardial visualization and confidence in interpretation of the stress study. Results Heart rate at the time of imaging was similar between the studies. Average time from cessation of exercise to start of imaging (21 vs. 31 seconds, p<0.001) and time to acquire stress images (20 vs. 51 seconds, p<0.001) was shorter for cardiac MR. The number of myocardial segments adequately visualized was significantly higher by cardiac MR at rest (99.8% versus 96.4%, p=0.002) and stress (99.8% versus 94.1%, p=0.001). The proportion of subjects in whom there was high confidence in the interpretation was higher for cardiac MR than echo (96% vs 60%, p=0.005). Conclusion Exercise stress cardiac MR to assess peak exercise wall motion is feasible and can be performed at least as rapidly as stress echo. PMID:24123562

Profiles of African American College Students' Alcohol Use and Sexual Behaviors: Associations With Stress, Racial Discrimination, and Social Support.

PubMed

Metzger, Isha W; Cooper, Shauna M; Ritchwood, Tiarney D; Onyeuku, Chisom; Griffin, Charity Brown

2017-01-01

Though studies show that alcohol use and sexual activity increase during emerging adulthood, few studies examine within-ethnic group differences, particularly among African American college students. This investigation utilized a latent class analytic methodology to identify risk behavior profiles of alcohol use (frequency and amount of alcohol consumed), sexual activity (number of intimate partners), and co-occurring risk behaviors (drinking before sexual intercourse) among 228 African American college students. This investigation also examined whether identified risk behavior profiles were associated with stress (interpersonal, intrapersonal, academic, and environmental), experiences of racial discrimination, and social support (from family, friends, and the college community). Results identified five distinct profiles within this sample: (a) High Sexual Risk-above-average sexual activity; (b) Abstainers-below-average alcohol use and sexual activity; (c) Low Risk-average alcohol use and sexual activity; (d) Alcohol Risk-above-average alcohol use and below-average sexual activity; and (e) Co-Occurring Risk-above-average alcohol use and sexual activity. Identified profiles differed across interpersonal and environmental stress, and self-reported frequency of experiences with racial discrimination. Implications for prevention programs and interventions aimed at reducing alcohol and sexual activity for African American college students are discussed.

A Tale of Two Features: Perception of Cantonese Lexical Tone and English Lexical Stress in Cantonese-English Bilinguals.

PubMed

Tong, Xiuli; Lee, Stephen Man Kit; Lee, Meg Mei Ling; Burnham, Denis

2015-01-01

This study investigated the similarities and differences in perception of Cantonese tones and English stress patterns by Cantonese-English bilingual children, adults, and English monolingual adults. All three groups were asked to discriminate pairs of syllables that minimally differed in either Cantonese tone or in English stress. Bilingual children's performance on tone perception was comparable to their performance on stress perception. By contrast, bilingual adults' performance on tone perception was lower than their performance on stress perception, and there was a similar pattern in English monolingual adults. Bilingual adults tended to perform better than English monolingual adults on both the tone and stress perception tests. A significant correlation between tone perception and stress perception performance was found in bilingual children but not in bilingual adults. All three groups showed lower accuracy in the high rising-low rising contrast than any of the other 14 Cantonese tone contrasts. The acoustic analyses revealed that average F0, F0 onset, and F0 major slope were the critical acoustic correlates of Cantonese tones, whereas multiple acoustic correlates were salient in English stress, including average F0, spectral balance, duration and intensity. We argue that participants' difficulty in perceiving high rising-low rising contrasts originated from the contrasts' similarities in F0 onset and average F0; indeed the difference between their major slopes was the only cue with which to distinguish them. Acoustic-perceptual correlation analyses showed that although the average F0 and F0 onset were associated with tone perception performance in all three groups, F0 major slope was only associated with tone perception in the bilingual adult group. These results support a dynamic interactive account of suprasegmental speech perception by emphasizing the positive prosodic transfer between Cantonese tone and English stress, and the role that level of bilingual language experience and age play in shaping suprasegmental speech perception.

A Tale of Two Features: Perception of Cantonese Lexical Tone and English Lexical Stress in Cantonese-English Bilinguals

PubMed Central

Tong, Xiuli; Burnham, Denis

2015-01-01

This study investigated the similarities and differences in perception of Cantonese tones and English stress patterns by Cantonese-English bilingual children, adults, and English monolingual adults. All three groups were asked to discriminate pairs of syllables that minimally differed in either Cantonese tone or in English stress. Bilingual children’s performance on tone perception was comparable to their performance on stress perception. By contrast, bilingual adults’ performance on tone perception was lower than their performance on stress perception, and there was a similar pattern in English monolingual adults. Bilingual adults tended to perform better than English monolingual adults on both the tone and stress perception tests. A significant correlation between tone perception and stress perception performance was found in bilingual children but not in bilingual adults. All three groups showed lower accuracy in the high rising-low rising contrast than any of the other 14 Cantonese tone contrasts. The acoustic analyses revealed that average F0, F0 onset, and F0 major slope were the critical acoustic correlates of Cantonese tones, whereas multiple acoustic correlates were salient in English stress, including average F0, spectral balance, duration and intensity. We argue that participants’ difficulty in perceiving high rising-low rising contrasts originated from the contrasts’ similarities in F0 onset and average F0; indeed the difference between their major slopes was the only cue with which to distinguish them. Acoustic-perceptual correlation analyses showed that although the average F0 and F0 onset were associated with tone perception performance in all three groups, F0 major slope was only associated with tone perception in the bilingual adult group. These results support a dynamic interactive account of suprasegmental speech perception by emphasizing the positive prosodic transfer between Cantonese tone and English stress, and the role that level of bilingual language experience and age play in shaping suprasegmental speech perception. PMID:26606073

Medial tibial plateau morphology and stress fracture location: A magnetic resonance imaging study

PubMed Central

Yukata, Kiminori; Yamanaka, Issei; Ueda, Yuzuru; Nakai, Sho; Ogasa, Hiroyoshi; Oishi, Yosuke; Hamawaki, Jun-ichi

2017-01-01

AIM To determine the location of medial tibial plateau stress fractures and its relationship with tibial plateau morphology using magnetic resonance imaging (MRI). METHODS A retrospective review of patients with a diagnosis of stress fracture of the medial tibial plateau was performed for a 5-year period. Fourteen patients [three female and 11 male, with an average age of 36.4 years (range, 15-50 years)], who underwent knee MRI, were included. The appearance of the tibial plateau stress fracture and the geometry of the tibial plateau were reviewed and measured on MRI. RESULTS Thirteen of 14 stress fractures were linear, and one of them stellated on MRI images. The location of fractures was classified into three types. Three fractures were located anteromedially (AM type), six posteromedially (PM type), and five posteriorly (P type) at the medial tibial plateau. In addition, tibial posterior slope at the medial tibial plateau tended to be larger when the fracture was located more posteriorly on MRI. CONCLUSION We found that MRI showed three different localizations of medial tibial plateau stress fractures, which were associated with tibial posterior slope at the medial tibial plateau. PMID:28660141

A 2D mechanical-magneto-thermal model for direction-dependent magnetoelectric effect in laminates

NASA Astrophysics Data System (ADS)

Zhang, Shunzu; Yao, Hong; Gao, Yuanwen

2017-04-01

A two dimensional (2D) mechanical-magneto-thermal model of direction-dependent magnetoelectric (ME) effect in Terfenol-D/PZT/Terfenol-D laminated composites is established. The expressions of ME coefficient at low and resonance frequencies are derived by the average field method, respectively. The prediction of theoretical model presents a good agreement with the experimental data. The combined effect of orientation-dependent stress and magnetic fields, as well as operating temperature on ME coefficient is discussed. It is shown that ME effect presents a significantly nonlinear change with the increasing pre-stress under different loading angles. There exists an optimal angle and value of pre-stress corresponding to the best ME effect, improving the angle of pre-stress can get more prominent ME coupling than in x axis state. Note that an optimal angle of magnetic field gradually increases with the rise of pre-stress, which can further lead to the enhancement of ME coefficient. Meanwhile, reducing the operating temperature can enhance ME coefficient. Furthermore, resonance frequency, affected by pre-stress, magnetic field and temperature via " ΔE effect", can enhance ME coefficient about 100 times than that at low frequency.

A method for mapping apparent stress and energy radiation applied to the 1994 Northridge earthquake fault zone

USGS Publications Warehouse

McGarr, A.; Fletcher, Joe B.

2000-01-01

Using the Northridge earthquake as an example, we demonstrate a new technique able to resolve apparent stress within subfaults of a larger fault plane. From the model of Wald et al. (1996), we estimated apparent stress for each subfault using τa = (G/β)/2 where G is the modulus of rigidity, β is the shear wave speed, and is the average slip rate. The image of apparent stress mapped over the Northridge fault plane supports the idea that the stresses causing fault slip are inhomogeneous, but limited by the strength of the crust. Indeed, over the depth range 5 to 17 km, maximum values of apparent stress for a given depth interval agree with τa(max)=0.06S(z), where S is the laboratory estimate of crustal strength as a function of depth z. The seismic energy from each subfault was estimated from the product τaDA, where A is subfault area and D its slip. Over the fault zone, we found that the radiated energy is quite variable spatially, with more than 50% of the total coming from just 15% of the subfaults.

Estimation of lattice strain in nanocrystalline RuO2 by Williamson-Hall and size-strain plot methods.

PubMed

Sivakami, R; Dhanuskodi, S; Karvembu, R

2016-01-05

RuO2 nanoparticles (RuO2 NPs) have been successfully synthesized by the hydrothermal method. Structure and the particle size have been determined by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM) and transmission electron microscopy (TEM). UV-Vis spectra reveal that the optical band gap of RuO2 nanoparticles is red shifted from 3.95 to 3.55eV. BET measurements show a high specific surface area (SSA) of 118-133m(2)/g and pore diameter (10-25nm) has been estimated by Barret-Joyner-Halenda (BJH) method. The crystallite size and lattice strain in the samples have been investigated by Williamson-Hall (W-H) analysis assuming uniform deformation, deformation stress and deformation energy density, and the size-strain plot method. All other relevant physical parameters including stress, strain and energy density have been calculated. The average crystallite size and the lattice strain evaluated from XRD measurements are in good agreement with the results of TEM. Copyright © 2015 Elsevier B.V. All rights reserved.

Academic-related stress among graduate students in nursing in a Jamaican school of nursing.

PubMed

Brown, Kimarie; Anderson-Johnson, Pauline; McPherson, Andrea Norman

2016-09-01

Graduate students perceive their education as highly stressful, have consistently rated their stress levels as above average and have consistently scored above average on stress scales. The consequences of stress include negative academic outcomes, reduction in cognitive ability, impaired coping and incompletion of graduate studies. Stress is also associated with physical and psychological symptoms such as altered appetite, sleep pattern disturbances and headache. A descriptive correlational design was used to determine the perceived levels and sources of academic-related stress among students enrolled in a Master of Science in Nursing (MScN) degree programme at school of nursing in urban section of Jamaica. The Perceived Stress Scale-14 and Stress Survey were used to collect data from the 81 students enrolled in full or part time study in the MScN programme. Univariate and bivariate analyses were conducted using SPSS version 20. The majority (50.9%) were moderately stressed while 22.8% and 24.6% had high and low levels of stress respectively. Stress associated with the preparation for and prospect of final examinations received the highest overall mean stress rating, causing "a lot of stress". Attendances at classes and relationships with lecturers received the lowest mean stress rating. Research was not listed as a stressor. Copyright © 2016 Elsevier Ltd. All rights reserved.

Plant moisture stress: a portable freezing-point meter compared with the psychrometer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cary, J.W.; Fisher, H.D.

A small portable instrument for measuring the freezing-point depression of plant tissue has been developed for field use. The instrument is easy to operate and can be constructed from materials costing less than $100. Moisture stress measurements made with the freezing-point meter on a variety of plants were compared with vapor pressure psychrometer measurements. Variation between duplicates in the freezing point averaged 1.2 bars, but differences between stress measurements made with the psychrometer and freezing-point instrument averaged 2.6 bars. 11 references, 5 figures, 2 tables.

Fluid losses and hydration status of industrial workers under thermal stress working extended shifts

PubMed Central

Brake, D; Bates, G

2003-01-01

Aims: To assess whether workers under significant thermal stress necessarily dehydrated during their exposure and whether "involuntary dehydration" was inevitable, as supported by ISO 9866 and other authorities. Other objectives were to quantify sweat rates against recommended occupational limits, to develop a dehydration protocol to assist with managing heat exposures, and to understand the role of meal breaks on extended shifts in terms of fluid replacement. Methods: A field investigation to examine the fluid consumption, sweat rates, and changes in the hydration state of industrial workers on extended (10, 12, and 12.5 hour) shifts under significant levels of thermal stress (wet bulb globe temperature (WBGT) >28°C) was conducted on 39 male underground miners. Urinary specific gravity was measured before, during, and at the completion of the working shift. Environmental conditions were measured hourly during the shift. Fluid replacement was measured during the working periods and during the meal breaks. Results: Average environmental conditions were severe (WBGT 30.9°C (SD 2.0°C), range 25.7–35.2°C). Fluid intake averaged 0.8 l/h during exposure (SD 0.3 l/h, range 0.3–1.5 l/h). Average urinary specific gravity at start, mid, and end of shift was 1.0251, 1.0248, and 1.0254 respectively; the differences between start and mid shift, mid and end shift, and start and end shift were not significant. However, a majority of workers were coming to work in a moderately hypohydrated state (average urinary specific gravity 1.024 (SD 0.0059)). A combined dehydration and heat illness protocol was developed. Urinary specific gravity limits of 1.022 for start of shift and 1.030 for end of shift were selected; workers exceeding these values were not allowed into the workplace (if the start of shift limit was exceeded) or were retested prior to their next working shift (if the end of shift limit was exceeded). A target of 1.015 as a euhydrated state for start of shift was adopted for workforce education. Conclusions: This study found that "involuntary dehydration" did not occur in well informed workers, which has implications for heat stress standards that do not make provision for full fluid replacement during heat exposure. Fluid replacement during meal breaks was not significantly increased above fluid replacement rates during work time, with implications for the duration and spacing of meal breaks on long shifts. Testing of urinary specific gravity was found to be a good indication of hydration status and a practical method of improving workforce awareness and understanding of this important risk factor. Approximately 10 000 dehydration tests have been conducted under the dehydration protocol in a workforce of 2000 persons exposed to thermal stress and has proved practical and reliable. PMID:12554834

12 CFR 252.154 - Annual stress test.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 12 Banks and Banking 4 2013-01-01 2013-01-01 false Annual stress test. 252.154 Section 252.154... (CONTINUED) ENHANCED PRUDENTIAL STANDARDS (REGULATION YY) Company-Run Stress Test Requirements for Banking... stress test. (a) General requirements—(1) Savings and loan holding companies with average total...

12 CFR 252.154 - Annual stress test.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 12 Banks and Banking 4 2014-01-01 2014-01-01 false Annual stress test. 252.154 Section 252.154... (CONTINUED) ENHANCED PRUDENTIAL STANDARDS (REGULATION YY) Company-Run Stress Test Requirements for Banking... stress test. (a) General requirements—(1) Savings and loan holding companies with average total...

Thermo-mechanically coupled fracture analysis of shape memory alloys using the extended finite element method

NASA Astrophysics Data System (ADS)

Hatefi Ardakani, S.; Ahmadian, H.; Mohammadi, S.

2015-04-01

In this paper, the extended finite element method is used for fracture analysis of shape memory alloys for both cases of super elastic and shape memory effects. Heat generation during the forward and reverse phase transformations can lead to temperature variation in the material because of strong thermo-mechanical coupling, which significantly influences the SMA mechanical behavior. First, the stationary crack mode is studied and the effects of loading rate on material behavior in the crack tip are examined. Then, the crack propagation analysis is performed in the presence of an initial crack by adopting a weighted averaging criterion, where the direction of crack propagation is determined by weighted averaging of effective stresses at all the integration points in the vicinity of the crack tip. Finally, several numerical examples are analyzed and the obtained results are compared with the available reference results.

Associations of oxidative stress and inflammatory biomarkers with chemically-characterized air pollutant exposures in an elderly cohort

PubMed Central

Zhang, Xian; Staimer, Norbert; Gillen, Daniel L.; Tjoa, Tomas; Schauer, James J.; Shafer, Martin M.; Hasheminassab, Sina; Pakbin, Payam; Vaziri, Nosratola D.; Sioutas, Constantinos; Delfino, Ralph J.

2016-01-01

Background Exposure to air pollution has been associated with cardiorespiratory morbidity and mortality. However, the chemical constituents and pollution sources underlying these associations remain unclear. Method We conducted a cohort panel study involving 97 elderly subjects living in the Los Angeles metropolitan area. Airway and circulating biomarkers of oxidative stress and inflammation were measured weekly over 12 weeks and included, exhaled breath condensate malondialdehyde (EBC MDA), fractional exhaled nitric oxide (FeNO), plasma oxidized low-density lipoprotein (oxLDL), and plasma interleukin-6 (IL-6). Exposures included 7-day personal nitrogen oxides (NOX), daily criteria-pollutant data, five-day average particulate matter (PM) measured in three size-fractions and characterized by chemical components including transition metals, and in vitro PM oxidative potential (dithiothreitol and macrophage reactive oxygen species). Associations between biomarkers and pollutants were assessed using linear mixed effects regression models. Results We found significant positive associations of airway oxidative stress and inflammation with traffic-related air pollutants, ultrafine particles and transition metals. Positive but nonsignificant associations were observed with PM oxidative potential. The strongest associations were observed among PM variables in the ultrafine range (PM <0.18 μm). It was estimated that an interquartile increase in 5-day average ultrafine polycyclic aromatic hydrocarbons was associated with a 6.3% (95% CI: 1.1%, 11.6%) increase in EBC MDA and 6.7% (95% CI: 3.4%, 10.2%) increase in FeNO. In addition, positive but nonsignificant associations were observed between oxLDL and traffic-related pollutants, ultrafine particles and transition metals while plasma IL-6 was positively associated with 1-day average traffic-related pollutants. Conclusion Our results suggest that exposure to pollutants with high oxidative potential (traffic-related pollutants, ultrafine particles, and transition metals) may lead to increased airway oxidative stress and inflammation in elderly adults. This observation was less clear with circulating biomarkers. PMID:27336235

Numerical simulation of microstructural damage and tensile strength of snow

NASA Astrophysics Data System (ADS)

Hagenmuller, Pascal; Theile, Thiemo C.; Schneebeli, Martin

2014-01-01

This contribution uses finite-element analysis to simulate microstructural failure processes and the tensile strength of snow. The 3-D structure of snow was imaged by microtomography. Modeling procedures used the elastic properties of ice with bond fracture assumptions as inputs. The microstructure experiences combined tensile and compressive stresses in response to macroscopic tensile stress. The simulated nonlocalized failure of ice lattice bonds before or after reaching peak stress creates a pseudo-plastic yield curve. This explains the occurrence of acoustic events observed in advance of global failure. The measured and simulated average tensile strengths differed by 35%, a typical range for strength measurements in snow given its low Weibull modulus. The simulation successfully explains damage, fracture nucleation, and strength according to the geometry of the microstructure of snow and the mechanical properties of ice. This novel method can be applied to more complex snow structures including the weak layers that cause avalanches.

Talking about health: correction employees' assessments of obstacles to healthy living.

PubMed

Morse, Tim; Dussetschleger, Jeffrey; Warren, Nicholas; Cherniack, Martin

2011-09-01

Describe health risks/obstacles to health among correctional employees. Mixed-methods approach combined results from four focus groups, 10 interviews, 335 surveys, and 197 physical assessments. Obesity levels were higher than national averages (40.7% overweight and 43.3% obese), with higher levels associated with job tenure, male gender, and working off-shift. Despite widespread concern about the lack of fitness, leisure exercise was higher than national norms. Respondents had higher levels of hypertension than national norms, with 31% of men and 25.8% of women hypertensive compared with 17.1% and 15.1% for national norms. Stress levels were elevated. Officers related their stress to concerns about security, administrative requirements, and work/family imbalance. High stress levels are reflected in elevated levels of hypertension. Correctional employees are at high risk for chronic disease, and environmental changes are needed to reduce risk factors. (C)2011The American College of Occupational and Environmental Medicine

A Brief Exploratory Report of Coping Strategies Among Police Recruits During Academy Training.

PubMed

Patterson, George T

2016-10-01

Few longitudinal studies have investigated the use of coping strategies among police recruits. This study investigated perceived life and work stressors, appraisal, and coping over a seven-month police recruit academy training program. Participants were 81 police recruits who completed the Ways of Coping Questionnaire at three time points approximately three months apart. The average age of the recruits was 27.6 years (SD = 5.1, range 20-51). Separate repeated measures analyses of variance were conducted to examine coping scores. Statistically significant decreases, although small, were observed in reported emotion-focused, problem-focused, and seeking social support coping strategies. Results suggested that as police recruits undergo academy training, they rely on fewer coping strategies to deal with life and work stress. More longitudinal studies are needed that assess the methods police recruits utilize to manage stress during academy training. Such results can inform stress management interventions. © The Author(s) 2016.

Effect of loading rate on the monotonic tensile behavior of a continuous-fiber-reinforced glass-ceramic matrix composite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Soerensen, B.F.; Holmes, J.W.

The stress-strain behavior of a continuous-fiber-reinforced ceramic matrix composite has been measured over a wide range of loading rates (0.01 to 500 MPa/s). It was found that the loading rate has a strong effect on almost every feature of the stress-strain curve: the proportionality stress, the composite strength and failure strain increase with increasing loading rate. The microstructural damage varies also with the loading rate; with increasing loading rate, the average matrix crack spacing increases and the average fiber pullout length decreases. Using simple models, it is suggested that these phenomena are caused partly by time-dependent matrix cracking (due tomore » stress corrosion) and partly by an increasing interfacial shear stress with loading rate.« less

Towards multilevel mental stress assessment using SVM with ECOC: an EEG approach.

PubMed

Al-Shargie, Fares; Tang, Tong Boon; Badruddin, Nasreen; Kiguchi, Masashi

2018-01-01

Mental stress has been identified as one of the major contributing factors that leads to various diseases such as heart attack, depression, and stroke. To avoid this, stress quantification is important for clinical intervention and disease prevention. This study aims to investigate the feasibility of exploiting electroencephalography (EEG) signals to discriminate between different stress levels. We propose a new assessment protocol whereby the stress level is represented by the complexity of mental arithmetic (MA) task for example, at three levels of difficulty, and the stressors are time pressure and negative feedback. Using 18-male subjects, the experimental results showed that there were significant differences in EEG response between the control and stress conditions at different levels of MA task with p values < 0.001. Furthermore, we found a significant reduction in alpha rhythm power from one stress level to another level, p values < 0.05. In comparison, results from self-reporting questionnaire NASA-TLX approach showed no significant differences between stress levels. In addition, we developed a discriminant analysis method based on multiclass support vector machine (SVM) with error-correcting output code (ECOC). Different stress levels were detected with an average classification accuracy of 94.79%. The lateral index (LI) results further showed dominant right prefrontal cortex (PFC) to mental stress (reduced alpha rhythm). The study demonstrated the feasibility of using EEG in classifying multilevel mental stress and reported alpha rhythm power at right prefrontal cortex as a suitable index.

Simulation fails to replicate stress in trainees performing a technical procedure in the clinical environment.

PubMed

Baker, B G; Bhalla, A; Doleman, B; Yarnold, E; Simons, S; Lund, J N; Williams, J P

2017-01-01

Simulation-based training (SBT) has become an increasingly important method by which doctors learn. Stress has an impact upon learning, performance, technical, and non-technical skills. However, there are currently no studies that compare stress in the clinical and simulated environment. We aimed to compare objective (heart rate variability, HRV) and subjective (state trait anxiety inventory, STAI) measures of stress theatre with a simulated environment. HRV recordings were obtained from eight anesthetic trainees performing an uncomplicated rapid sequence induction at pre-determined procedural steps using a wireless Polar RS800CX monitor © in an emergency theatre setting. This was repeated in the simulated environment. Participants completed an STAI before and after the procedure. Eight trainees completed the study. The theatre environment caused an increase in objective stress vs baseline (p = .004). There was no significant difference between average objective stress levels across all time points (p = .20) between environments. However, there was a significant interaction between the variables of objective stress and environment (p = .045). There was no significant difference in subjective stress (p = .27) between environments. Simulation was unable to accurately replicate the stress of the technical procedure. This is the first study that compares the stress during SBT with the theatre environment and has implications for the assessment of simulated environments for use in examinations, rating of technical and non-technical skills, and stress management training.

Recent changes of rice heat stress in Jiangxi province, southeast China.

PubMed

Huang, Jin; Zhang, Fangmin; Xue, Yan; Lin, Jie

2017-04-01

Around the intensity, frequency, duration, accumulated temperature, and even extremes of high-temperature events, nine selected temperature-related indices were used to explore the space and time changes of rice heat stress in Jiangxi province, southeast China. Several statistical methods including Mann-Kendall trend test (M-K test) and principal component analysis (PCA) were used in this study, and main results were listed as follows: (1) The changes in the intensity indices for high-temperature events were more significant, it was mainly embodied in that more than 80 % of stations had positive trends. (2) R-mode PCA was applied to the multiannual average values of nine selected indices of whole stations, and the results showed that the higher hazard for rice heat stress could be mainly detected in the middle and northeast area of Jiangxi. (3) S-mode PCA was applied to the integrated heat stress index series, and the results demonstrated that Jiangxi could be divided into four sub-regions with different variability in rice heat stress. However, all the sub-regions are dominated by increasing tendencies in rice heat stress since 1990. (4) Further analysis indicated that the western north Pacific sub-tropical high (WPSH) had the significant dominant influence on the rice heat stress in Jiangxi province.

The development and validation of a numerical integration method for non-linear viscoelastic modeling

PubMed Central

Ramo, Nicole L.; Puttlitz, Christian M.

2018-01-01

Compelling evidence that many biological soft tissues display both strain- and time-dependent behavior has led to the development of fully non-linear viscoelastic modeling techniques to represent the tissue’s mechanical response under dynamic conditions. Since the current stress state of a viscoelastic material is dependent on all previous loading events, numerical analyses are complicated by the requirement of computing and storing the stress at each step throughout the load history. This requirement quickly becomes computationally expensive, and in some cases intractable, for finite element models. Therefore, we have developed a strain-dependent numerical integration approach for capturing non-linear viscoelasticity that enables calculation of the current stress from a strain-dependent history state variable stored from the preceding time step only, which improves both fitting efficiency and computational tractability. This methodology was validated based on its ability to recover non-linear viscoelastic coefficients from simulated stress-relaxation (six strain levels) and dynamic cyclic (three frequencies) experimental stress-strain data. The model successfully fit each data set with average errors in recovered coefficients of 0.3% for stress-relaxation fits and 0.1% for cyclic. The results support the use of the presented methodology to develop linear or non-linear viscoelastic models from stress-relaxation or cyclic experimental data of biological soft tissues. PMID:29293558

Acoustic-radiation stress in solids. I - Theory

NASA Technical Reports Server (NTRS)

Cantrell, J. H., Jr.

1984-01-01

The general case of acoustic-radiation stress associated with quasi-compressional and quasi-shear waves propagating in infinite and semiinfinite lossless solids of arbitrary crystalline symmetry is studied. The Boussinesq radiation stress is defined and found to depend directly on an acoustic nonlinearity parameter which characterizes the radiation-induced static strain, a stress-generalized nonlinearity parameter which characterizes the stress nonlinearity, and the energy density of the propagating wave. Application of the Boltzmann-Ehrenfest principle of adiabatic invariance to a self-constrained system described by the nonlinear equations of motion allows the acoustic-radiation-induced static strain to be identified with a self-constrained variation in the time-averaged product of the internal energy density and displacement gradient. The time-averaged product is scaled by the acoustic nonlinearity parameter and represents the first-order nonlinearity in the virial theorem. Finally, the relationship between the Boussinesq and the Cauchy radiation stress is obtained in a closed three-dimensional form.

Gender-specific selection in utero among contemporary human birth cohorts.

PubMed

Catalano, Ralph; Ahern, Jennifer; Bruckner, Tim; Anderson, Elizabeth; Saxton, Katherine

2009-05-01

Much literature argues that natural selection has conserved mechanisms by which stressed females cull frail males in utero. This argument implies that males from low sex ratio birth cohorts should, on average, live longer than those from high sex ratio cohorts. Research reports such associations but these tests use completed lifespan as the outcome and, therefore, must end with cohorts born in 1913 because too many males survive from more contemporary cohorts to determine average lifespan. The empirical literature does not, therefore, address whether selection affects male mortality in contemporary cohorts. We apply time-series methods to monthly cohorts born in California between 1989 and 2003 to measure the association between the ratio of male to female live births and infant mortality, controlling for all forms of autocorrelation that induce spurious correlations. Consistent with theories of selection in utero, we find a positive correlation between cohort sex ratio and male infant mortality. The results suggest that natural selection conserved the stress mechanism in females to end the gestation of relatively less fit males and that this mechanism manifests itself in contemporary human societies.

Properties of the Residual Stress of the Temporally Filtered Navier-Stokes Equations

NASA Technical Reports Server (NTRS)

Pruett, C. D.; Gatski, T. B.; Grosch, C. E.; Thacker, W. D.

2002-01-01

The development of a unifying framework among direct numerical simulations, large-eddy simulations, and statistically averaged formulations of the Navier-Stokes equations, is of current interest. Toward that goal, the properties of the residual (subgrid-scale) stress of the temporally filtered Navier-Stokes equations are carefully examined. Causal time-domain filters, parameterized by a temporal filter width 0 less than Delta less than infinity, are considered. For several reasons, the differential forms of such filters are preferred to their corresponding integral forms; among these, storage requirements for differential forms are typically much less than for integral forms and, for some filters, are independent of Delta. The behavior of the residual stress in the limits of both vanishing and in infinite filter widths is examined. It is shown analytically that, in the limit Delta to 0, the residual stress vanishes, in which case the Navier-Stokes equations are recovered from the temporally filtered equations. Alternately, in the limit Delta to infinity, the residual stress is equivalent to the long-time averaged stress, and the Reynolds-averaged Navier-Stokes equations are recovered from the temporally filtered equations. The predicted behavior at the asymptotic limits of filter width is further validated by numerical simulations of the temporally filtered forced, viscous Burger's equation. Finally, finite filter widths are also considered, and a priori analyses of temporal similarity and temporal approximate deconvolution models of the residual stress are conducted.

Shear-stress fluctuations and relaxation in polymer glasses

NASA Astrophysics Data System (ADS)

Kriuchevskyi, I.; Wittmer, J. P.; Meyer, H.; Benzerara, O.; Baschnagel, J.

2018-01-01

We investigate by means of molecular dynamics simulation a coarse-grained polymer glass model focusing on (quasistatic and dynamical) shear-stress fluctuations as a function of temperature T and sampling time Δ t . The linear response is characterized using (ensemble-averaged) expectation values of the contributions (time averaged for each shear plane) to the stress-fluctuation relation μsf for the shear modulus and the shear-stress relaxation modulus G (t ) . Using 100 independent configurations, we pay attention to the respective standard deviations. While the ensemble-averaged modulus μsf(T ) decreases continuously with increasing T for all Δ t sampled, its standard deviation δ μsf(T ) is nonmonotonic with a striking peak at the glass transition. The question of whether the shear modulus is continuous or has a jump singularity at the glass transition is thus ill posed. Confirming the effective time-translational invariance of our systems, the Δ t dependence of μsf and related quantities can be understood using a weighted integral over G (t ) .

Effects of Temperature and Strain Rate on Tensile Deformation Behavior of 9Cr-0.5Mo-1.8W-VNb Ferritic Heat-Resistant Steel

NASA Astrophysics Data System (ADS)

Guo, Xiaofeng; Weng, Xiaoxiang; Jiang, Yong; Gong, Jianming

2017-09-01

A series of uniaxial tensile tests were carried out at different strain rate and different temperatures to investigate the effects of temperature and strain rate on tensile deformation behavior of P92 steel. In the temperature range of 30-700 °C, the variations of flow stress, average work-hardening rate, tensile strength and ductility with temperature all show three temperature regimes. At intermediate temperature, the material exhibited the serrated flow behavior, the peak in flow stress, the maximum in average work-hardening rate, and the abnormal variations in tensile strength and ductility indicates the occurrence of DSA, whereas the sharp decrease in flow stress, average work-hardening rate as well as strength values, and the remarkable increase in ductility values with increasing temperature from 450 to 700 °C imply that dynamic recovery plays a dominant role in this regime. Additionally, for the temperature ranging from 550 to 650 °C, a significant decrease in flow stress values is observed with decreasing in strain rate. This phenomenon suggests the strain rate has a strong influence on flow stress. Based on the experimental results above, an Arrhenius-type constitutive equation is proposed to predict the flow stress.

Nonlinear mesomechanics of composites with periodic microstructure

NASA Technical Reports Server (NTRS)

Walker, Kevin P.; Jordan, Eric H.; Freed, Alan D.

1989-01-01

This work is concerned with modeling the mechanical deformation or constitutive behavior of composites comprised of a periodic microstructure under small displacement conditions at elevated temperature. A mesomechanics approach is adopted which relates the microimechanical behavior of the heterogeneous composite with its in-service macroscopic behavior. Two different methods, one based on a Fourier series approach and the other on a Green's function approach, are used in modeling the micromechanical behavior of the composite material. Although the constitutive formulations are based on a micromechanical approach, it should be stressed that the resulting equations are volume averaged to produce overall effective constitutive relations which relate the bulk, volume averaged, stress increment to the bulk, volume averaged, strain increment. As such, they are macromodels which can be used directly in nonlinear finite element programs such as MARC, ANSYS and ABAQUS or in boundary element programs such as BEST3D. In developing the volume averaged or efective macromodels from the micromechanical models, both approaches will require the evaluation of volume integrals containing the spatially varying strain distributions throughout the composite material. By assuming that the strain distributions are spatially constant within each constituent phase-or within a given subvolume within each constituent phase-of the composite material, the volume integrals can be obtained in closed form. This simplified micromodel can then be volume averaged to obtain an effective macromodel suitable for use in the MARC, ANSYS and ABAQUS nonlinear finite element programs via user constitutive subroutines such as HYPELA and CMUSER. This effective macromodel can be used in a nonlinear finite element structural analysis to obtain the strain-temperature history at those points in the structure where thermomechanical cracking and damage are expected to occur, the so called damage critical points of the structure.

Beyond the Map: Enamel Distribution Characterized from 3D Dental Topography

PubMed Central

Thiery, Ghislain; Lazzari, Vincent; Ramdarshan, Anusha; Guy, Franck

2017-01-01

Enamel thickness is highly susceptible to natural selection because thick enamel may prevent tooth failure. Consequently, it has been suggested that primates consuming stress-limited food on a regular basis would have thick-enameled molars in comparison to primates consuming soft food. Furthermore, the spatial distribution of enamel over a single tooth crown is not homogeneous, and thick enamel is expected to be more unevenly distributed in durophagous primates. Still, a proper methodology to quantitatively characterize enamel 3D distribution and test this hypothesis is yet to be developed. Unworn to slightly worn upper second molars belonging to 32 species of anthropoid primates and corresponding to a wide range of diets were digitized using high resolution microcomputed tomography. In addition, their durophagous ability was scored from existing literature. 3D average and relative enamel thickness were computed based on the volumetric reconstruction of the enamel cap. Geometric estimates of their average and relative enamel-dentine distance were also computed using 3D dental topography. Both methods gave different estimations of average and relative enamel thickness. This study also introduces pachymetric profiles, a method inspired from traditional topography to graphically characterize thick enamel distribution. Pachymetric profiles and topographic maps of enamel-dentine distance are combined to assess the evenness of thick enamel distribution. Both pachymetric profiles and topographic maps indicate that thick enamel is not significantly more unevenly distributed in durophagous species, except in Cercopithecidae. In this family, durophagous species such as mangabeys are characterized by an uneven thick enamel and high pachymetric profile slopes at the average enamel thickness, whereas non-durophagous species such as colobine monkeys are not. These results indicate that the distribution of thick enamel follows different patterns across anthropoids. Primates might have developed different durophagous strategies to answer the selective pressure exerted by stress-limited food. PMID:28785226

Stress Drop Estimates from Induced Seismic Events in the Fort Worth Basin, Texas

NASA Astrophysics Data System (ADS)

Jeong, S. J.; Stump, B. W.; DeShon, H. R.

2017-12-01

Since the beginning of Barnett shale oil and gas production in the Fort Worth Basin, there have been earthquake sequences, including multiple magnitude 3.0+ events near the DFW International Airport, Azle, Irving-Dallas, and throughout Johnson County (Cleburne and Venus). These shallow depth earthquakes (2 to 8 km) have not exceeded magnitude 4.0 and have been widely felt; the close proximity of these earthquakes to a large population center motivates an assessment of the kinematics of the events in order to provide more accurate ground motion predictions. Previous studies have estimated average stress drops for the DFW airport and Cleburne earthquakes at 10 and 43 bars, respectively. Here, we calculate stress drops for Azle, Irving-Dallas and Venus earthquakes using seismic data from local (≤25 km) and regional (>25 km) seismic networks. Events with magnitudes above 2.5 are chosen to ensure adequate signal-to-noise. Stress drops are estimated by fitting the Brune earthquake model to the observed source spectrum with correction for propagation path effects and a local site effect using a high-frequency decay parameter, κ, estimated from acceleration spectrum. We find that regional average stress drops are similar to those estimated using local data, supporting the appropriateness of the propagation path and site corrections. The average stress drop estimates are 72 bars, which range from 7 to 240 bars. The results are consistent with global averages of 10 to 100 bars for intra-plate earthquakes and compatible with stress drops of DFW airport and Cleburne earthquakes. The stress drops show a slight breakdown in self-similarity with increasing moment magnitude. The breakdown of similarity for these events requires further study because of the limited magnitude range of the data. These results suggest that strong motions and seismic hazard from an injection-induced earthquake can be expected to be similar to those for tectonic events taking into account the shallow depth of induced earthquakes.

Sectoral contributions to surface water stress in the coterminous United States

NASA Astrophysics Data System (ADS)

Averyt, K.; Meldrum, J.; Caldwell, P.; Sun, G.; McNulty, S.; Huber-Lee, A.; Madden, N.

2013-09-01

Here, we assess current stress in the freshwater system based on the best available data in order to understand possible risks and vulnerabilities to regional water resources and the sectors dependent on freshwater. We present watershed-scale measures of surface water supply stress for the coterminous United States (US) using the water supply stress index (WaSSI) model which considers regional trends in both water supply and demand. A snapshot of contemporary annual water demand is compared against different water supply regimes, including current average supplies, current extreme-year supplies, and projected future average surface water flows under a changing climate. In addition, we investigate the contributions of different water demand sectors to current water stress. On average, water supplies are stressed, meaning that demands for water outstrip natural supplies in over 9% of the 2103 watersheds examined. These watersheds rely on reservoir storage, conveyance systems, and groundwater to meet current water demands. Overall, agriculture is the major demand-side driver of water stress in the US, whereas municipal stress is isolated to southern California. Water stress introduced by cooling water demands for power plants is punctuated across the US, indicating that a single power plant has the potential to stress water supplies at the watershed scale. On the supply side, watersheds in the western US are particularly sensitive to low flow events and projected long-term shifts in flow driven by climate change. The WaSSI results imply that not only are water resources in the southwest in particular at risk, but that there are also potential vulnerabilities to specific sectors, even in the ‘water-rich’ southeast.

Investigation of Occupational Stress and its Relationship with the Demographic Characteristics of Workers in Ilam, Iran.

PubMed

Rahmani, Abdolrasoul; Khodaei, Roghiyeh; Mahmodkhani, Somayeh; Moslemi, Mehrnoush; Gharagozlou, Faramarz; Ahmadnezhad, Iman; Karchani, Mohsen; Vatani, Javad

2013-01-01

Workers are more susceptible to stress disorder for several reasons. The aim of this study was to investigate occupational stress among workers and other personnel at the ZardjinBaft Workshop in Ilam, Iran, and to examine the relationship between occupational stress and several parameters, such as age, gender, marital status, educational level, work experience, tobacco use, body mass index (BMI), and the type of work. This was a descriptive, cross-sectional study that was performed in June 2010. The sample population that was studied consisted of all of the workers and other personnel (130 people) at ZardjinBaft Workshop in Ilam, Iran. They were studied using Cooper's standard questionnaire for stress in the work environment, and we examined the relationship between stress, as the dependent variable, and the eight independent variables mentioned in the Abstract. In the sample population that was studied, severe stress was not observed in most of the sections of the workshop. In addition, using the analysis of variance test (ANOVA), no significant relationship was observed between the average degree of stress and the average demographic characteristics. However, the average stress level had significant relationships with the level of education, work experience, and the type of work, suggesting that stress increases as the level of education increases. In addition, in the beginning and early years of employment, medium levels of stress were observed, and the prevalence of stress decreased after the first 10 years of employment. In addition, workers in the ventilation section of the factory had the highest stress levels. The fear of losing their jobs was the main factor that caused stress among the workers at ZardjinBaft Workshop in Ilam. We suggest that managers consider the high importance of stress in the work environment. They should be able to recognize when workers are stressed and offer them assistance and training. They also can eliminate the factors that cause stress in the work environment by taking preventive action. In parallel, workers should try to interact well with their managers and talk to her or him about the conditions of their jobs.

Stress release structures for actuator beams with a stress gradient

NASA Astrophysics Data System (ADS)

Klaasse, G.; Puers, R.; Tilmans, H. A. C.

2007-10-01

Stress release structures are introduced in fixed-fixed beams or membranes for releasing average stress. The influence of a stress gradient on the initial deformation of a fixed-fixed beam with stress release structures is studied in this paper. The objective is to obtain actuator beams that are insensitive to both the average stress and the stress gradient. The target application for the actuator beam in this study is a surface micromachined variable capacitor with a fixed electrode at the center of the beam. An analytical one-dimensional model is derived which predicts the initial deflection of a fixed-fixed beam with one stress release structure at any location and with two stress release structures, placed symmetrically with respect to the center of the beam at any location. The initial center deflection of the beam with one stress release structure was found from the analytical modeling to be zero for a specific set of parameters, but a negative deflection is always present for this specific configuration, leading to beams that touch the substrate at undesired positions, which implies non-functional devices. The configuration with the two symmetrically placed stress release structures can have zero initial center deflection, according to the analytical model, when the stress release structures are placed at a distance of a quarter of the beam length from the anchor points. Finite-element simulations are performed for both configurations and validate the theory. Deviations from the assumed model result in small initial center deflections, but can be compensated for by a little shift of the stress release structures. Experiments are performed for less ideal configurations with two stress release structures where they are shaped as round meanders. These structures do not fully release the stress and the center deflection therefore depends on the average stress to some extent, as demonstrated by finite element simulations. However, the location can be chosen such that there is an initial center deflection that is close to zero. These experiments are, therefore, in qualitative agreement with the analytical model.

A cross-sectional study of the association between mobile phone use and symptoms of ill health

PubMed Central

2016-01-01

Objectives This study analyzed the associations between mobile phone call frequency and duration with non-specific symptoms. Methods This study was conducted with a population group including 532 non-patient adults established by the Korean Genome and Epidemiology Study. The pattern of phone call using a mobile phone was investigated through face-to-face interview. Structured methods applied to quantitatively assess health effects are Headache Impact Test-6 (HIT-6), Psychosocial Well-being Index-Short Form, Beck Depression Inventory, Korean-Instrumental Activities of Daily Living, Perceived Stress Scale (PSS), Pittsburgh Sleep Quality Index, and 12-item Short Form Health Survey where a higher score represents a higher greater health effect. Results The average daily phone call frequency showed a significant correlation with the PSS score in female subjects. Increases in the average duration of one phone call were significantly correlated with increases in the severity of headaches in both sexes. The mean (standard deviation) HIT-6 score in the subgroup of subjects whose average duration of one phone call was five minutes or longer was 45.98 (8.15), as compared with 42.48 (7.20) in those whose average duration of one phone call was <5 minutes. The severity of headaches was divided into three levels according to the HIT-6 score (little or no impact/moderate impact/substantial or severe impact), and a logistic regression analysis was performed to investigate the association between an increased phone call duration and the headache severity. When the average duration of one phone call was five minutes or longer, the odds ratio (ORs) and the 95% confidence intervals (CIs) for the moderate impact group were 2.22 and 1.18 to 4.19, respectively. The OR and 95% CI for the substantial or severe impact group were 4.44 and 2.11 to 8.90, respectively. Conclusions Mobile phone call duration was not significantly associated with stress, sleep, cognitive function, or depression, but was associated with the severity of headaches. PMID:27788568

Profiles of African American College Students’ Alcohol Use and Sexual Behaviors: Associations With Stress, Racial Discrimination, and Social Support

PubMed Central

Metzger, Isha W.; Cooper, Shauna M.; Ritchwood, Tiarney D.; Onyeuku, Chisom; Griffin, Charity Brown

2017-01-01

Though studies show that alcohol use and sexual activity increase during emerging adulthood, few studies examine within–ethnic group differences, particularly among African American college students. This investigation utilized a latent class analytic methodology to identify risk behavior profiles of alcohol use (frequency and amount of alcohol consumed), sexual activity (number of intimate partners), and co-occurring risk behaviors (drinking before sexual intercourse) among 228 African American college students. This investigation also examined whether identified risk behavior profiles were associated with stress (interpersonal, intraperso-nal, academic, and environmental), experiences of racial discrimination, and social support (from family, friends, and the college community). Results identified five distinct profiles within this sample: (a) High Sexual Risk—above-average sexual activity; (b) Abstainers—below-average alcohol use and sexual activity; (c) Low Risk—average alcohol use and sexual activity; (d) Alcohol Risk—above-average alcohol use and below-average sexual activity; and (e) Co-Occurring Risk—above-average alcohol use and sexual activity. Identified profiles differed across interpersonal and environmental stress, and self-reported frequency of experiences with racial discrimination. Implications for prevention programs and interventions aimed at reducing alcohol and sexual activity for African American college students are discussed. PMID:27215314

About the coupling of turbulence closure models with averaged Navier-Stokes equations

NASA Technical Reports Server (NTRS)

Vandromme, D.; Ha Minh, H.

1986-01-01

The MacCormack implicit predictor-corrector model (1981) for numerical solution of the coupled Navier-Stokes equations for turbulent flows is extended to nonconservative multiequation turbulence models, as well as the inclusion of second-order Reynolds stress turbulence closure. A scalar effective pressure turbulent contribution to the pressure field is defined to approximate the effects of the Reynolds stress in strongly sheared flows. The Jacobian matrices of the transport equations are diagonalized to reduce the required computer memory and run time. Techniques are defined for including turbulence in the diagonalization. Application of the method is demonstrated with solutions generated for transonic nozzle flow and for the interaction between a supersonic flat plate boundary layer and a 12 deg compression-expansion ramp.

Stress fracture as a complication of autogenous bone graft harvest from the distal tibia.

PubMed

Chou, Loretta B; Mann, Roger A; Coughlin, Michael J; McPeake, William T; Mizel, Mark S

2007-02-01

Autogenous bone graft from the distal tibia provides cancellous bone graft for foot and ankle operations, and it has osteogenic and osteoconductive properties. The site is in close proximity to the foot and ankle, and published retrospective studies show low morbidity from the procedure. One-hundred autografts were obtained from the distal tibia between 2000 and 2003. In four cases the distal tibial bone graft harvest resulted in a stress fracture. There were three women and one man. The average time of diagnosis of the stress fracture from the operation was 1.8 months. All stress fractures healed with a short course (average 2.4 months) of cast immobilization. This study demonstrated that a stress fracture from the donor site of autogenous bone graft of the distal tibia occurs and can be successfully treated nonoperatively.

Vacuum quantum stress tensor fluctuations: A diagonalization approach

NASA Astrophysics Data System (ADS)

Schiappacasse, Enrico D.; Fewster, Christopher J.; Ford, L. H.

2018-01-01

Large vacuum fluctuations of a quantum stress tensor can be described by the asymptotic behavior of its probability distribution. Here we focus on stress tensor operators which have been averaged with a sampling function in time. The Minkowski vacuum state is not an eigenstate of the time-averaged operator, but can be expanded in terms of its eigenstates. We calculate the probability distribution and the cumulative probability distribution for obtaining a given value in a measurement of the time-averaged operator taken in the vacuum state. In these calculations, we study a specific operator that contributes to the stress-energy tensor of a massless scalar field in Minkowski spacetime, namely, the normal ordered square of the time derivative of the field. We analyze the rate of decrease of the tail of the probability distribution for different temporal sampling functions, such as compactly supported functions and the Lorentzian function. We find that the tails decrease relatively slowly, as exponentials of fractional powers, in agreement with previous work using the moments of the distribution. Our results lend additional support to the conclusion that large vacuum stress tensor fluctuations are more probable than large thermal fluctuations, and may have observable effects.

Acculturation Stress and Bullying among Immigrant Youths in Spain

ERIC Educational Resources Information Center

Messinger, Adam M.; Nieri, Tanya A.; Villar, Paula; Luengo, Maria Angeles

2012-01-01

Few bullying studies focus on immigrant youths or acculturation stress as a risk factor for bullying and being bullied. Employing a sample of 1,157 foreign-born secondary students in Spain, we found that acculturation stress was widely experienced, although the average level of stress was moderate. Five percent of the sample reported being…

Mind-Body Skills Training for Resident Wellness: A Pilot Study of a Brief Mindfulness Intervention.

PubMed

Romcevich, Laura E; Reed, Suzanne; Flowers, Stacy R; Kemper, Kathi J; Mahan, John D

2018-01-01

Interventions to address burnout include mind-body skills training (MBST), but few studies have evaluated the feasibility of MBST for busy pediatric residents. In this pilot study, we tested the feasibility of a brief MBST intervention, using in-person peer-led training supported by online modules, to decrease stress and burnout in pediatric resident physicians. Of 99 (10%) residents, 10 residents at Nationwide Children's Hospital in Ohio participated in up to four 90-minute MBST sessions more than 1 month, led by a co-resident with 5 years of informal training in mind-body skills. Participants were offered 8 assigned online modules through OSU Center for Integrative Health and Wellness. Measures including Maslach Burnout Inventory (MBI), Cohen's Perceived Stress, Smith's Brief Resilience, Cognitive and Affective Mindfulness Scale-Revised, and Neff's Self-Compassion Scale (NSS) were administered before (T1) and after (T2) the course. Participants were offered optional monthly "maintenance" sessions for 6 months and completed a third set of measures at this follow-up (T3). The residents completed an average of 4.3/8 online modules and attended an average of 2.8/4 in-person sessions. There was significant improvement in positive attitude, perceived stress, and resilience post intervention (T2). Follow-up evaluation (T3) also demonstrated significant improvement in burnout (depersonalization) and mindfulness. More than 75% of participants found the course worthwhile. A short mixed-method mindfulness-based skills course may be a practical way to offer resilience and stress management training to busy resident physicians.

Prevalence of Burnout Syndrome in Patients Admitted with Acute Coronary Syndrome

PubMed Central

Prosdócimo, Ana Cláudia Giaxa; Lucina, Luciane Boreki; Marcia, Olandoski; Jobs, Priscila Megda João; Schio, Nicolle Amboni; Baldanzi, Fernanda Fachin; Costantini, Costantino Ortiz; Benevides-Pereira, Ana Maria Teresa; Guarita-Souza, Luiz Cesar; Faria-Neto, José Rocha

2015-01-01

Background Burnout Syndrome is the extreme emotional response to chronic occupational stress, manifesting as physical and mental exhaustion. Although associated with higher prevalence of cardiovascular risk factors, no study so far has evaluated whether the Burnout Syndrome could be a prevalent factor in non-elderly individuals active in the labor market, admitted for acute coronary syndrome (ACS). Objective To evaluate the prevalence of the Burnout Syndrome in non-elderly, economically active patients, hospitalized with ACS. Methods Cross-sectional study conducted in a tertiary and private cardiology center, with economically active patients aged <65 years, hospitalized with diagnosis of ACS. The Burnout Syndrome was evaluated with the Burnout Syndrome Inventory (BSI), which assesses workplace conditions and four dimensions that characterize the syndrome: emotional exhaustion (EE), emotional distancing (EmD), dehumanization (De) and professional fulfillment (PF). The Lipp’s Stress Symptoms Inventory for Adults (LSSI) was applied to evaluate global stress. Results Of 830 patients evaluated with suspected ACS, 170 met the study criteria, 90% of which were men, overall average age was 52 years, and 40.5% had an average income above 11 minimum wages. The prevalence of the Burnout Syndrome was 4.1%. When we evaluated each dimension individually, we found high EE in 34.7%, high De in 52.4%, high EDi in 30.6%, and low PF in 5.9%. The overall prevalence of stress was 87.5%. Conclusion We found a low prevalence of Burnout Syndrome in an economically active, non-elderly population among patients admitted for ACS in a tertiary and private hospital. PMID:25517388

Stress induced magnetic-domain evolution in magnetoelectric composites

NASA Astrophysics Data System (ADS)

Trivedi, Harsh; Shvartsman, Vladimir V.; Lupascu, Doru C.; Medeiros, Marco S. A.; Pullar, Robert C.

2018-06-01

Local observation of the stress mediated magnetoelectric (ME) effect in composites has gained a great deal of interest over the last decades. However, there is an apparent lack of rigorous methods for a quantitative characterization of the ME effect at the local scale, especially in polycrystalline microstructures. In the present work, we address this issue by locally probing the surface magnetic state of barium titante–hexagonal barium ferrite (BaTiO3–BaFe12O19) ceramic composites using magnetic force microscopy (MFM). The effect of the piezoelectrically induced local stress on the magnetostrictive component (BaFe12O19, BaM) was observed in the form of the evolution of the magnetic domains. The local piezoelectric stress was induced by applying a voltage to the neighboring BaTiO3 grains, using a conductive atomic force microscopy tip. The resulting stochastic evolution of magnetic domains was studied in the context of the induced magnetoelastic anisotropy. In order to overcome the ambiguity in the domain changes observed by MFM, certain generalizations about the observed MFM contrast are put forward, followed by application of an algorithm for extracting the average micromagnetic changes. An average change in domain wall thickness of 50 nm was extracted, giving a lower limit on the corresponding induced magnetoelastic anisotropy energy. Furthermore, we demonstrate that this induced magnetomechanical energy is approximately equal to the K1 magnetocrystalline anisotropy constant of BaM, and compare it with a modeled value of applied elastic energy density. The comparison allowed us to judge the quality of the interfaces in the composite system, by roughly gauging the energy conversion ratio.

Predictors of job satisfaction and burnout among tuberculosis management nurses and physicians

PubMed Central

2016-01-01

OBJECTIVES: This study examined job satisfaction, empowerment, job stress, and burnout among tuberculosis management nurses and physicians in public healthcare institutions. METHODS: This was a cross-sectional study analyzing survey data collected from 249 nurses and 57 physicians in 105 public health centers, three public tuberculosis hospitals, and one tertiary hospital. The survey questionnaire comprised general characteristics, work-related characteristics, and four index scales (job satisfaction, empowerment, job stress, and burnout). The two-sample t-test was used to estimate the mean differences in the four index scales. Multiple regression analysis was used to determine whether general and work-related characteristics affected the four index scales. RESULTS: The job satisfaction and empowerment scores of the nurses were lower than those of the physicians. Except for the tuberculosis-specialized hospitals alone, the average job satisfaction scores of nurses were higher than those of physicians. Moreover, the nurses reported more job stress and burnout than did the physicians in tuberculosis departments in public healthcare institutions in Korea; in particular, the burnout reported by nurses was significantly higher than that reported by physicians at the National Medical Center. Marital status, nursing position, number of coworkers, the average number of days of overtime work per month, self-rated health, and hospital type were associated with the four index scales. CONCLUSIONS: Overall, nurses were more vulnerable to job stress and burnout than physicians. Reducing the workload of nurses by ensuring the presence of sufficient nursing staff and equipment, as well as by equipping facilities to prevent tuberculosis infections, should be considered priorities. PMID:26971698

Day-to-Day Inconsistency in Parent Knowledge: Links with Youth Health and Parents’ Stress

PubMed Central

Lippold, Melissa A.; McHale, Susan M.; Davis, Kelly D.; Kossek, Ellen Ernst

2015-01-01

Purpose Considerable evidence documents the linkages between higher levels of parental knowledge about youth activities and positive youth outcomes. This study investigated how day-to-day inconsistency in parental knowledge of youth activities was linked to youth behavioral, psychological, and physical health as well as parents’ stress. Methods Participants were employees in the Information Technology division of a Fortune 500 company and their children (N =129, Mean age youth = 13.39 years, 55% female). Data were collected from parents and youth via separate workplace and in-home surveys as well as telephone diary surveys on 8 consecutive evenings. We assessed day-to-day inconsistency in parental knowledge across these eight calls. Results Parents differed in their knowledge from day to day almost as much as their average knowledge scores differed from those of other parents. Controlling for mean levels of knowledge, youth whose parents exhibited more knowledge inconsistency reported more physical health symptoms (e.g., colds, flu). Knowledge inconsistency was also associated with more risky behavior for girls but greater psychological well-being for older adolescents. Parents who reported more stressors also had higher knowledge inconsistency. Conclusions Assessing only average levels of parental knowledge does not fully capture how this parenting dimension is associated with youth health. Consistent knowledge may promote youth physical health and less risky behavior for girls. Yet knowledge inconsistency also may reflect normative increases in autonomy as it was positively associated with psychological well-being for older adolescents. Given the linkages between parental stress and knowledge inconsistency, parent interventions should include stress-management components. PMID:25703318

Novel Gyroscopic Mounting for Crystal Oscillators to Increase Short and Medium Term Stability under Highly Dynamic Conditions

PubMed Central

Abedi, Maryam; Jin, Tian; Sun, Kewen

2015-01-01

In this paper, a gyroscopic mounting method for crystal oscillators to reduce the impact of dynamic loads on their output stability has been proposed. In order to prove the efficiency of this mounting approach, each dynamic load-induced instability has been analyzed in detail. A statistical study has been performed on the elevation angle of the g-sensitivity vector of Stress Compensated-cut (SC-cut) crystals. The analysis results show that the proposed gyroscopic mounting method gives good performance for host vehicle attitude changes. A phase noise improvement of 27 dB maximum and 5.7 dB on average can be achieved in the case of steady state loads, while under sinusoidal vibration conditions, the maximum and average phase noise improvement are as high as 24 dB and 7.5 dB respectively. With this gyroscopic mounting method, random vibration-induced phase noise instability is reduced 30 dB maximum and 8.7 dB on average. Good effects are apparent for crystal g-sensitivity vectors with low elevation angle φ and azimuthal angle β. under highly dynamic conditions, indicating the probability that crystal oscillator instability will be significantly reduced by using the proposed mounting approach. PMID:26091393

Dislocation, crystallite size distribution and lattice strain of magnesium oxide nanoparticles

NASA Astrophysics Data System (ADS)

Sutapa, I. W.; Wahid Wahab, Abdul; Taba, P.; Nafie, N. L.

2018-03-01

The oxide of magnesium nanoparticles synthesized using sol-gel method and analysis of the structural properties was conducted. The functional groups of nanoparticles has been analysed by Fourier Transform Infrared Spectroscopy (FT-IR). Dislocations, average size of crystal, strain, stress, the energy density of crystal, crystallite size distribution and morphologies of the crystals were determined based on X-ray diffraction profile analysis. The morphological of the crystal was analysed based on the image resulted from SEM analysis. The crystallite size distribution was calculated with the contention that the particle size has a normal logarithmic form. The most orientations of crystal were determined based on the textural crystal from diffraction data of X-ray diffraction profile analysis. FT-IR results showed the stretching vibration mode of the Mg-O-Mg in the range of 400.11-525 cm-1 as a broad band. The average size crystal of nanoparticles resulted is 9.21 mm with dislocation value of crystal is 0.012 nm-2. The strains, stress, the energy density of crystal are 1.5 x 10-4 37.31 MPa; 0.72 MPa respectively. The highest texture coefficient value of the crystal is 0.98. This result is supported by morphological analysis using SEM which shows most of the regular cubic-shaped crystals. The synthesis method is suitable for simple and cost-effective synthesis model of MgO nanoparticles.

[Intensification of post-traumatic stress disorder of Siberian deportees from the North-East region of Poland].

PubMed

Monieta, Adela; Anczurowski, Wojciech

2004-01-01

Presentation of Post-Traumatic Stress Disorder based on the approach of various authors concentrating, upon the concept of the American classification: DSM III (1980) and DSM IV (1994). We acknowledged the necessity of displaying empirical results of intensification of PTSD among the Siberian deportees population in the region of North-East part of Poland. In our analysis, we stressed the importance of the distant in time, psychological consequences of dwelling in extremely difficult living conditions that often threatened the life of those who had been deported to Siberia between 1939 and 1956. 40 "Siberian deportees" (20 men and 20 women) were examined. The method of PTSD-Interview (PTSD-I) was used here in order to obtain, in each individual case, the indicatory number indispensable for the statistical analysis. An average result of PTSD intensification in the case of women reaches a "very significant" level and in the case of men it is even higher. The disparity between the average results of women and of men are statistically significant (p<0.05). This research has confirmed the assumptions that suffering from trauma in the early stage of development (within the age range of 8-15) leaves a permanent mark in the human psyche. Statistical analysis revealed a high level of intensification of PTSD among the population of the "Siberian deportees" from the North-East region of Poland.

Upscaling the Navier-Stokes Equation for Turbulent Flows in Porous Media Using a Volume Averaging Method

NASA Astrophysics Data System (ADS)

Wood, Brian; He, Xiaoliang; Apte, Sourabh

2017-11-01

Turbulent flows through porous media are encountered in a number of natural and engineered systems. Many attempts to close the Navier-Stokes equation for such type of flow have been made, for example using RANS models and double averaging. On the other hand, Whitaker (1996) applied volume averaging theorem to close the macroscopic N-S equation for low Re flow. In this work, the volume averaging theory is extended into the turbulent flow regime to posit a relationship between the macroscale velocities and the spatial velocity statistics in terms of the spatial averaged velocity only. Rather than developing a Reynolds stress model, we propose a simple algebraic closure, consistent with generalized effective viscosity models (Pope 1975), to represent the spatial fluctuating velocity and pressure respectively. The coefficients (one 1st order, two 2nd order and one 3rd order tensor) of the linear functions depend on averaged velocity and gradient. With the data set from DNS, performed with inertial and turbulent flows (pore Re of 300, 500 and 1000) through a periodic face centered cubic (FCC) unit cell, all the unknown coefficients can be computed and the closure is complete. The macroscopic quantity calculated from the averaging is then compared with DNS data to verify the upscaling. NSF Project Numbers 1336983, 1133363.

Observations of the Space-time Structure of Flow, Vorticity and Stress over Orbital-scale Ripples

NASA Astrophysics Data System (ADS)

Hare, J.; Hay, A. E.; Cheel, R. A.; Zedel, L. J.

2012-12-01

Results are presented from a laboratory investigation of the spatial and temporal structure at turbulence-resolving scales of the flow, vorticity and stress over equilibrium orbital-scale sand ripples. The ripples were created in 0.153 mm median diameter sand, at 10 s period and an excursion of 0.5 m, using the oscillating tray apparatus described in Hay et al. (JGR-Oceans, 2012). Vertical profiles of velocity above the bed were obtained at 40 Hz and 3 mm vertical resolution using a wide-band coherent Doppler profiler (MFDop). Through runs at different positions of the MFDop relative to a particular ripple crest, phase-averaged measures of the flow over a full ripple wavelength were obtained as a function of phase during the forcing cycle. These measurements are used to determine the formation of the lee vortex and the position of the point of reattachment. Estimates of the phase-averaged bottom stress (obtained using the vertical integral of the defect acceleration, the Reynolds stress and the law-of-the-wall) as a function of position along the ripple profile are inter-compared.Phase-averaged horizontal velocity over one ripple where the black line indicates the sediment-water interface. Phase-averaged vertical velocity over one ripple where the black line indicates the sediment-water interface.

Episode-Specific Drinking-to-Cope Motivation and Next-Day Stress-Reactivity

PubMed Central

Armeli, Stephen; O’Hara, Ross E.; Covault, Jon; Scott, Denise M.; Tennen, Howard

2016-01-01

Background Research consistently shows drinking-to-cope (DTC) motivation is uniquely associated with drinking-related problems. We furthered this line of research by examining whether DTC motivation is predictive of processes indicative of poor emotion regulation. Specifically, we tested whether nighttime levels of episode-specific DTC motivation, controlling for drinking level, were associated with intensified affective reactions to stress the following day (i.e., stress-reactivity). Design and Methods We used a micro-longitudinal design to test this hypothesis in two college student samples from demographically distinct institutions: a large, rural state university (N = 1421; 54% female) and an urban historically Black college/university (N = 452; 59% female). Results In both samples the within-person association between daily stress and negative affect on days following drinking episodes was stronger in the positive direction when previous night’s drinking was characterized by relatively higher levels of DTC motivation. We also found evidence among students at the state university that average levels of DTC motivation moderated the daily stress-negative affect association. Conclusions Findings are consistent with the notion that DTC motivation confers a unique vulnerability that affects processes associated with emotion regulation. PMID:26691066

Traction force and tension fluctuations in growing axons

NASA Astrophysics Data System (ADS)

Urbach, Jeffrey; Polackwich, Jamie; Koch, Daniel; McAllister, Ryan; Geller, Herbert

Actively generated mechanical forces play a central role in axon growth and guidance during nervous system development. We describe the dynamics of traction stresses from growth cones of actively advancing axons from postnatal rat DRG neurons. By tracking the movement of the growth cone and analyzing the traction stresses in a co-moving reference frame, we show that there is a clear and consistent average stress field underlying the complex spatial stresses present at any one time. The average stress field has strong maxima on the sides of the growth cone, directed inward toward the growth cone neck. This pattern represents a Contractile stress contained within the growth cone, and a net force that is balanced by the axon tension. In addition, using high time-resolution measurements, we show that the stress field is composed of fluctuating local stress peaks, with a population of peaks whose lifetime distribution follows an exponential decay, and a small number of very long-lived peaks. We also find that the tension appears to vary randomly over short time scales, roughly consistent with the lifetime of the stress peaks, suggesting that the tension fluctuations originate from stochastic adhesion dynamics.

Variation in the reference Shields stress for bed load transport in gravel‐bed streams and rivers

USGS Publications Warehouse

Mueller, Erich R.; Pitlick, John; Nelson, Jonathan M.

2005-01-01

The present study examines variations in the reference shear stress for bed load transport (τr) using coupled measurements of flow and bed load transport in 45 gravel‐bed streams and rivers. The study streams encompass a wide range in bank‐full discharge (1–2600 m3/s), average channel gradient (0.0003–0.05), and median surface grain size (0.027–0.21 m). A bed load transport relation was formed for each site by plotting individual values of the dimensionless transport rate W* versus the reach‐average dimensionless shear stress τ*. The reference dimensionless shear stress τ*r was then estimated by selecting the value of τ* corresponding to a reference transport rate of W* = 0.002. The results indicate that the discharge corresponding to τ*r averages 67% of the bank‐full discharge, with the variation independent of reach‐scale morphologic and sediment properties. However, values of τ*r increase systematically with average channel gradient, ranging from 0.025–0.035 at sites with slopes of 0.001–0.006 to values greater than 0.10 at sites with slopes greater than 0.02. A corresponding relation for the bank‐full dimensionless shear stress τ*bf, formulated with data from 159 sites in North America and England, mirrors the relation between τ*r and channel gradient, suggesting that the bank‐full channel geometry of gravel‐ and cobble‐bedded streams is adjusted to a relatively constant excess shear stress, τ*bf − τ*r, across a wide range of slopes.

Measurement of Young's modulus and residual stress of thin SiC layers for MEMS high temperature applications

NASA Astrophysics Data System (ADS)

Pabst, Oliver; Schiffer, Michael; Obermeier, Ernst; Tekin, Tolga; Lang, Klaus Dieter; Ngo, Ha-Duong

2011-06-01

Silicon carbide (SiC) is a promising material for applications in harsh environments. Standard silicon (Si) microelectromechanical systems (MEMS) are limited in operating temperature to temperatures below 130 °C for electronic devices and below 600 °C for mechanical devices. Due to its large bandgap SiC enables MEMS with significantly higher operating temperatures. Furthermore, SiC exhibits high chemical stability and thermal conductivity. Young's modulus and residual stress are important mechanical properties for the design of sophisticated SiC-based MEMS devices. In particular, residual stresses are strongly dependent on the deposition conditions. Literature values for Young's modulus range from 100 to 400 GPa, and residual stresses range from 98 to 486 MPa. In this paper we present our work on investigating Young's modulus and residual stress of SiC films deposited on single crystal bulk silicon using bulge testing. This method is based on measurement of pressure-dependent membrane deflection. Polycrystalline as well as single crystal cubic silicon carbide samples are studied. For the samples tested, average Young's modulus and residual stress measured are 417 GPa and 89 MPa for polycrystalline samples. For single crystal samples, the according values are 388 GPa and 217 MPa. These results compare well with literature values.

A Comparison of Artificial Intelligence Methods on Determining Coronary Artery Disease

NASA Astrophysics Data System (ADS)

Babaoğlu, Ismail; Baykan, Ömer Kaan; Aygül, Nazif; Özdemir, Kurtuluş; Bayrak, Mehmet

The aim of this study is to show a comparison of multi-layered perceptron neural network (MLPNN) and support vector machine (SVM) on determination of coronary artery disease existence upon exercise stress testing (EST) data. EST and coronary angiography were performed on 480 patients with acquiring 23 verifying features from each. The robustness of the proposed methods is examined using classification accuracy, k-fold cross-validation method and Cohen's kappa coefficient. The obtained classification accuracies are approximately 78% and 79% for MLPNN and SVM respectively. Both MLPNN and SVM methods are rather satisfactory than human-based method looking to Cohen's kappa coefficients. Besides, SVM is slightly better than MLPNN when looking to the diagnostic accuracy, average of sensitivity and specificity, and also Cohen's kappa coefficient.

A pilot study on mindfulness based stress reduction for smokers

PubMed Central

Davis, James M; Fleming, Michael F; Bonus, Katherine A; Baker, Timothy B

2007-01-01

Background Mindfulness means paying attention in the present moment, non-judgmentally, without commentary or decision-making. We report results of a pilot study designed to test the feasibility of using Mindfulness Based Stress Reduction (MBSR) (with minor modifications) as a smoking intervention. Methods MBSR instructors provided instructions in mindfulness in eight weekly group sessions. Subjects attempted smoking cessation during week seven without pharmacotherapy. Smoking abstinence was tested six weeks after the smoking quit day with carbon monoxide breath test and 7-day smoking calendars. Questionnaires were administered to evaluate changes in stress and affective distress. Results 18 subjects enrolled in the intervention with an average smoking history of 19.9 cigarettes per day for 26.4 years. At the 6-week post-quit visit, 10 of 18 subjects (56%) achieved biologically confirmed 7-day point-prevalent smoking abstinence. Compliance with meditation was positively associated with smoking abstinence and decreases in stress and affective distress. Discussions and conclusion The results of this study suggest that mindfulness training may show promise for smoking cessation and warrants additional study in a larger comparative trial. PMID:17254362

The α–ω phase transition in shock-loaded titanium

DOE PAGES

Jones, David R.; Morrow, Benjamin M.; Trujillo, Carl P.; ...

2017-07-28

Here, we present a series of experiments probing the martensitic α–ω (hexagonal close-packed to simple hexagonal) transition in titanium under shock-loading to peak stresses around 15 GPa. Gas-gun plate impact techniques were used to locate the α–ω transition stress with a laser-based velocimetry diagnostic. A change in the shock-wave profile at 10.1 GPa suggests the transition begins at this stress. A second experiment shock-loaded and then soft-recovered a similar titanium sample. We then analyzed this recovered material with electron-backscatter diffraction methods, revealing on average approximately 65% retained ω phase. Furthermore, based on careful analysis of the microstructure, we propose thatmore » the titanium never reached a full ω state, and that there was no observed phase-reversion from ω to α. Texture analysis suggests that any α titanium found in the recovered sample is the original α. The data show that both the α and ω phases are stable and can coexist even though the shock-wave presents as steady-state, at these stresses.« less

Determining suspended sediment particle size information from acoustical and optical backscatter measurements

NASA Astrophysics Data System (ADS)

Lynch, James F.; Irish, James D.; Sherwood, Christopher R.; Agrawal, Yogesh C.

1994-08-01

During the winter of 1990-1991 an Acoustic BackScatter System (ABSS), five Optical Backscatterance Sensors (OBSs) and a Laser In Situ Settling Tube (LISST) were deployed in 90 m of water off the California coast for 3 months as part of the Sediment Transport Events on Shelves and Slopes (STRESS) experiment. By looking at sediment transport events with both optical (OBS) and acoustic (ABSS) sensors, one obtains information about the size of the particles transported as well as their concentration. Specifically, we employ two different methods of estimating "average particle size". First, we use vertical scattering intensity profile slopes (acoustical and optical) to infer average particle size using a Rouse profile model of the boundary layer and a Stokes law fall velocity assumption. Secondly, we use a combination of optics and acoustics to form a multifrequency (two frequency) inverse for the average particle size. These results are compared to independent observations from the LISST instrument, which measures the particle size spectrum in situ using laser diffraction techniques. Rouse profile based inversions for particle size are found to be in good agreement with the LISST results except during periods of transport event initiation, when the Rouse profile is not expected to be valid. The two frequency inverse, which is boundary layer model independent, worked reasonably during all periods, with average particle sizes correlating well with the LISST estimates. In order to further corroborate the particle size inverses from the acoustical and optical instruments, we also examined size spectra obtained from in situ sediment grab samples and water column samples (suspended sediments), as well as laboratory tank experiments using STRESS sediments. Again, good agreement is noted. The laboratory tank experiment also allowed us to study the acoustical and optical scattering law characteristics of the STRESS sediments. It is seen that, for optics, using the cross sectional area of an equivalent sphere is a very good first approximation whereas for acoustics, which is most sensitive in the region ka ˜ 1, the particle volume itself is best sensed. In concluding, we briefly interpret the history of some STRESS transport events in light of the size distribution and other information available. For one of the events "anomalous" suspended particle size distributions are noted, i.e. larger particles are seen suspended before finer ones. Speculative hypotheses for why this signature is observed are presented.

Fiber stress values for design of glulam timber utility structures

Treesearch

R. Hernandez; R. C. Moody; R. H. Falk

In this study, we developed a simple equation to calculate average fiber stress values for design of glued-laminated (glulam) timber utility structures as a function of design bending stress. We took design stress in bending values specified by the American Institute of Timber Construction (AITC) for various combinations of glulam timber, applied appropriate end-use...

Extraction and analysis of cortisol from human and monkey hair.

PubMed

Meyer, Jerrold; Novak, Melinda; Hamel, Amanda; Rosenberg, Kendra

2014-01-24

The stress hormone cortisol (CORT) is slowly incorporated into the growing hair shaft of humans, nonhuman primates, and other mammals. We developed and validated a method for CORT extraction and analysis from rhesus monkey hair and subsequently adapted this method for use with human scalp hair. In contrast to CORT "point samples" obtained from plasma or saliva, hair CORT provides an integrated measure of hypothalamic-pituitary-adrenocortical (HPA) system activity, and thus physiological stress, during the period of hormone incorporation. Because human scalp hair grows at an average rate of 1 cm/month, CORT levels obtained from hair segments several cm in length can potentially serve as a biomarker of stress experienced over a number of months. In our method, each hair sample is first washed twice in isopropanol to remove any CORT from the outside of the hair shaft that has been deposited from sweat or sebum. After drying, the sample is ground to a fine powder to break up the hair's protein matrix and increase the surface area for extraction. CORT from the interior of the hair shaft is extracted into methanol, the methanol is evaporated, and the extract is reconstituted in assay buffer. Extracted CORT, along with standards and quality controls, is then analyzed by means of a sensitive and specific commercially available enzyme immunoassay (EIA) kit. Readout from the EIA is converted to pg CORT per mg powdered hair weight. This method has been used in our laboratory to analyze hair CORT in humans, several species of macaque monkeys, marmosets, dogs, and polar bears. Many studies both from our lab and from other research groups have demonstrated the broad applicability of hair CORT for assessing chronic stress exposure in natural as well as laboratory settings.

Combined In-Plane and Through-the-Thickness Analysis for Failure Prediction of Bolted Composite Joints

NASA Technical Reports Server (NTRS)

Kradinov, V.; Madenci, E.; Ambur, D. R.

2004-01-01

Although two-dimensional methods provide accurate predictions of contact stresses and bolt load distribution in bolted composite joints with multiple bolts, they fail to capture the effect of thickness on the strength prediction. Typically, the plies close to the interface of laminates are expected to be the most highly loaded, due to bolt deformation, and they are usually the first to fail. This study presents an analysis method to account for the variation of stresses in the thickness direction by augmenting a two-dimensional analysis with a one-dimensional through the thickness analysis. The two-dimensional in-plane solution method based on the combined complex potential and variational formulation satisfies the equilibrium equations exactly, and satisfies the boundary conditions and constraints by minimizing the total potential. Under general loading conditions, this method addresses multiple bolt configurations without requiring symmetry conditions while accounting for the contact phenomenon and the interaction among the bolts explicitly. The through-the-thickness analysis is based on the model utilizing a beam on an elastic foundation. The bolt, represented as a short beam while accounting for bending and shear deformations, rests on springs, where the spring coefficients represent the resistance of the composite laminate to bolt deformation. The combined in-plane and through-the-thickness analysis produces the bolt/hole displacement in the thickness direction, as well as the stress state in each ply. The initial ply failure predicted by applying the average stress criterion is followed by a simple progressive failure. Application of the model is demonstrated by considering single- and double-lap joints of metal plates bolted to composite laminates.

Averaging interval selection for the calculation of Reynolds shear stress for studies of boundary layer turbulence.

NASA Astrophysics Data System (ADS)

Lee, Zoe; Baas, Andreas

2013-04-01

It is widely recognised that boundary layer turbulence plays an important role in sediment transport dynamics in aeolian environments. Improvements in the design and affordability of ultrasonic anemometers have provided significant contributions to studies of aeolian turbulence, by facilitating high frequency monitoring of three dimensional wind velocities. Consequently, research has moved beyond studies of mean airflow properties, to investigations into quasi-instantaneous turbulent fluctuations at high spatio-temporal scales. To fully understand, how temporal fluctuations in shear stress drive wind erosivity and sediment transport, research into the best practice for calculating shear stress is necessary. This paper builds upon work published by Lee and Baas (2012) on the influence of streamline correction techniques on Reynolds shear stress, by investigating the time-averaging interval used in the calculation. Concerns relating to the selection of appropriate averaging intervals for turbulence research, where the data are typically non-stationary at all timescales, are well documented in the literature (e.g. Treviño and Andreas, 2000). For example, Finnigan et al. (2003) found that underestimating the required averaging interval can lead to a reduction in the calculated momentum flux, as contributions from turbulent eddies longer than the averaging interval are lost. To avoid the risk of underestimating fluxes, researchers have typically used the total measurement duration as a single averaging period. For non-stationary data, however, using the whole measurement run as a single block average is inadequate for defining turbulent fluctuations. The data presented in this paper were collected in a field study of boundary layer turbulence conducted at Tramore beach near Rosapenna, County Donegal, Ireland. High-frequency (50 Hz) 3D wind velocity measurements were collected using ultrasonic anemometry at thirteen different heights between 0.11 and 1.62 metres above the bed. A technique for determining time-averaging intervals for a series of anemometers stacked in a close vertical array is presented. A minimum timescale is identified using spectral analysis to determine the inertial sub-range, where energy is neither produced nor dissipated but passed down to increasingly smaller scales. An autocorrelation function is then used to derive a scaling pattern between anemometer heights, which defines a series of averaging intervals of increasing length with height above the surface. Results demonstrate the effect of different averaging intervals on the calculation of Reynolds shear stress and highlight the inadequacy of using the total measurement duration as a single block average. Lee, Z. S. & Baas, A. C. W. (2012). Streamline correction for the analysis of boundary layer turbulence. Geomorphology, 171-172, 69-82. Treviño, G. and Andreas, E.L., 2000. Averaging Intervals For Spectral Analysis Of Nonstationary Turbulence. Boundary-Layer Meteorology, 95(2): 231-247. Finnigan, J.J., Clement, R., Malhi, Y., Leuning, R. and Cleugh, H.A., 2003. Re-evaluation of long-term flux measurement techniques. Part I: Averaging and coordinate rotation. Boundary-Layer Meteorology, 107(1): 1-48.

Hydraulic-fracturing measurmements in two boreholes near the Spent Fuel Test-Climax, Climax Stock, Nevada Test Site

USGS Publications Warehouse

Ellis, William L.

1983-01-01

Hydraulic-fracturing measurements are used to infer the magnitude of the least principal stress in the vicinity of the Spent Fuel Test-Climax, located in the Climax stock at the Nevada Test Site. The measurements, made at various depths in two exploratory boreholes, suggest that the local stress field is not uniform. Estimates of the least principal stress magnitude vary over distances of a few tens of meters, with the smaller values averaging 2.9 MPa and the larger values averaging 5.5 MPa. The smaller values are in agreement with the minimum-stress magnitude of 2.8 MPa determined in a nearby drift in 1979, using an overcoring technique. Jointing in the granitic rock mass and (or) the influence of nearby faults may account for the apparent variation in minimum-stress magnitude indicated by the hydrofracture data.

Chronic Stress in the Mother-Infant Dyad: Maternal Hair Cortisol, Infant Salivary Cortisol and Interactional Synchrony

PubMed Central

Tarullo, Amanda R.; St. John, Ashley Moore; Meyer, Jerrold S.

2017-01-01

Stress physiology is shaped by early experience, with enduring effects on health. The relation of chronic maternal physiological stress, as indexed by hair cortisol, to infants' stress systems and to mother-infant interaction quality has not been established. We examined maternal hair and salivary cortisol, six-month-old infants' salivary cortisol, and mother-infant interaction in 121 mother-infant dyads. High maternal hair cortisol was related to higher infant average salivary cortisol concentration. Maternal hair cortisol and bedtime salivary cortisol were both uniquely related to infant bedtime salivary cortisol. Mothers with higher hair cortisol were more intrusive and had lower positive engagement synchrony with their infants. Maternal intrusiveness moderated the association of maternal hair cortisol and infant salivary cortisol, such that maternal hair and infant average salivary cortisol were related only when mothers were more intrusive. Maternal chronic physiological stress may upregulate infants' developing stress systems, particularly in the context of lower mother-infant interaction quality. PMID:28391126

Taking aim at nurse stress: a call to action.

PubMed

Kashani, Mariam; Eliasson, Arn; Chrosniak, Linda; Vernalis, Marina

2010-02-01

The study investigates stress levels and related behaviors of nurses in a military medical center during wartime. In 2007, nurses completed a questionnaire survey with objective validation of data in a subsample using actigraphy over 12 weeks. Of 270 nurses, 255 (94%) returned surveys. A total of 81% reported moderately high or high stress with sources listed as work (66%) and fatigue (39%). Many reported coming to work despite feeling ill and/or stressed (13.6 days/3 months). In contrast, morale was high or moderately high in 71%. Nurses reported an average of 5.5 hours of sleep/night, 8.8 h/wk taken for self, and 3.8 h/wk for exercise. Actigraphy data showed an average of 6.0 hours of sleep/night. These findings highlight a mismatch between stress levels and coping perceptions indicating an inability to properly care for self. To manage the effects of chronic stress, nurse leaders should implement systems targeting healthy life balance.

Chronic stress in the mother-infant dyad: Maternal hair cortisol, infant salivary cortisol and interactional synchrony.

PubMed

Tarullo, Amanda R; St John, Ashley Moore; Meyer, Jerrold S

2017-05-01

Stress physiology is shaped by early experience, with enduring effects on health. The relation of chronic maternal physiological stress, as indexed by hair cortisol, to infants' stress systems and to mother-infant interaction quality has not been established. We examined maternal hair and salivary cortisol, six-month-old infants' salivary cortisol, and mother-infant interaction in 121 mother-infant dyads. High maternal hair cortisol was related to higher infant average salivary cortisol concentration. Maternal hair cortisol and bedtime salivary cortisol were both uniquely related to infant bedtime salivary cortisol. Mothers with higher hair cortisol were more intrusive and had lower positive engagement synchrony with their infants. Maternal intrusiveness moderated the association of maternal hair cortisol and infant salivary cortisol, such that maternal hair and infant average salivary cortisol were related only when mothers were more intrusive. Maternal chronic physiological stress may upregulate infants' developing stress systems, particularly in the context of lower mother-infant interaction quality. Copyright © 2017 Elsevier Inc. All rights reserved.

Quantifying the Physiological Stress Response to Simulated Maritime Pilotage Tasks: The Influence of Task Complexity and Pilot Experience.

PubMed

Main, Luana C; Wolkow, Alexander; Chambers, Timothy P

2017-11-01

The aim of this study was to quantify the stress associated with performing maritime pilotage tasks in a high-fidelity simulator. Eight trainee and 13 maritime pilots completed two simulated pilotage tasks of varying complexity. Salivary cortisol samples were collected pre- and post-simulation for both trials. Heart rate was measured continuously throughout the study. Significant changes in salivary cortisol (P = 0.000, η = 0.139), average (P = 0.006, η = 0.087), and peak heart rate (P = 0.013, η = 0.077) from pre- to postsimulation were found. Varying task complexity did partially influence stress response; average (P = 0.016, η = 0.026) and peak heart rate (P = 0.034, η = 0.020) were higher in the experimental condition. Trainees also recorded higher average (P = 0.000, η = 0.054) and peak heart rates (P = 0.027, η = 0.022). Performing simulated pilotage tasks evoked a measurable stress response in both trainee and expert maritime pilots.

Stress modeling in colloidal dispersions undergoing non-viscometric flows

NASA Astrophysics Data System (ADS)

Dolata, Benjamin; Zia, Roseanna

2017-11-01

We present a theoretical study of the stress tensor for a colloidal dispersion undergoing non-viscometric flow. In such flows, the non-homogeneous suspension stress depends on not only the local average total stresslet-the sum of symmetric first moments of both the hydrodynamic traction and the interparticle force-but also on the average quadrupole, octupole, and higher-order moments. To compute the average moments, we formulate a six dimensional Smoluchowski equation governing the microstructural evolution of a suspension in an arbitrary fluid velocity field. Under the conditions of rheologically slow flow, where the Brownian relaxation of the particles is much faster than the spatiotemporal evolution of the flow, the Smoluchowski equation permits asymptotic solution, revealing a suspension stress that follows a second-order fluid constitutive model. We obtain a reciprocal theorem and utilize it to show that all constitutive parameters of the second-order fluid model may be obtained from two simpler linear-response problems: a suspension undergoing simple shear and a suspension undergoing isotropic expansion. The consequences of relaxing the assumption of rheologically slow flow, including the appearance of memory and microcontinuum behaviors, are discussed.

Risk Factor, Job Stress and Quality of Life in Workers With Lower Extremity Pain Who Use Video Display Terminals

PubMed Central

2018-01-01

Objective To investigate the general characteristics of video display terminal (VDT) workers with lower extremity pain, to identify the risk factors of work-related lower extremity pain, and to examine the relationship between work stress and health-related quality of life. Methods A questionnaire about the general characteristics of the survey group and the musculoskeletal symptom was used. A questionnaire about job stress used the Korean Occupational Stress Scale and medical outcome study 36-item Short Form Health Survey (SF-36) to assess health-related quality of life. Results There were 1,711 subjects in the lower extremity group and 2,208 subjects in the control group. Age, sex, hobbies, and feeling of loading affected lower extremity pain as determined in a crossover analysis of all variables with and without lower extremity pain. There were no statistically significant difference between the two groups in terms of job stress and SF-36 values of the pain and control groups. Conclusion Job stress in VDT workers was higher than average, and the quality of life decreased as the stress increased. Factors such as younger age, women, hobbies other than exercise, and feeling of loading influenced lower extremity pain of workers. Further long-term follow-up and supplementary studies are needed to identify risk factors for future lower extremity pain, taking into account ergonomic factors such as worker's posture. PMID:29560330

Effects of Meridian Acupressure Massage on Body Composition, Edema, Stress, and Fatigue in Postpartum Women.

PubMed

Jung, Geum-Sook; Choi, In-Ryoung; Kang, Hee-Young; Choi, Eun-Young

2017-10-01

This study aims to investigate the effects of meridian acupressure massage on body composition, edema, stress, and fatigue in postpartum women. A quasi-experimental design with a nonequivalent control group was utilized. The Postpartum Care Center of Women's Hospital in Gwangju City, Republic of Korea. The study group consisted of 39 postpartum women, 19 in the experimental group and 20 in the control group, recruited from the postpartum care center of Women's Hospital in Gwangju city, South Korea. The experimental group was provided with meridian acupressure massage for 90 min daily over 5 days as an experimental therapy. Body composition (body weight, BMI, total body water, ECW ratio, LBM, and body fat) Edema (subjective edema, average girth of the upper limbs, and average girth of the lower limbs), Stress (psychological stress and physical stress), and Fatigue. The experimental group demonstrated a significantly larger decrease compared with the control group in measures of body composition, edema, total subjective stress, psychological stress, and subjective fatigue. Meridian acupressure massage can hasten the return to original body composition after childbirth.

Impact of Bony Stress Injuries on Professional Basketball Performance

PubMed Central

Khan, Moin; Madden, Kim; Rogowski, Joseph P.; Stotts, Jeff; Burrus, Matthew Tyrrell; Samani, Marisa; Sikka, Robby Singh; Bedi, Asheesh

2017-01-01

Objectives: Players in the National Basketball Association (NBA) subject their lower extremities to significant repetitive loading during the season as well as during off-season training. Little is known about the incidence and impact of lower extremity bony stress injuries in these athletes. Methods: Using the player injury database maintained by the NBA Players’ Association, all bony stress injuries from 1992 to May 2016 were identified. Those not involving the lower extremity were excluded from the study. Stress fractures and stress reactions were grouped together. Number of games missed due to the injury as well as player statistics including points per game (ppg), assists per game (apg), steals per game (spg), and blocks per game (bpg) were collected from two years prior to the injury to two years after the injury. Results: 76 lower extremity bony stress injuries were identified involving 75 different NBA players with an average player age of 25.4 ± 4.1 years. 55.3% (42/76) involved the foot, 21.1% (16/76) involved the ankle or fibula, 17.1% (13/76) involved the tibia, and 6.6% (5/76) involved either the knee or patella. The majority of injuries occurred in season 82.9% (63/76) with half of the injuries occurring within the first 6 weeks of the season. 38.2% (29/76) of these injuries were managed surgically. An average of 25.1 ± 21.3 games were missed. 19.7% (15/76) of patients who sustained a stress fracture also had a subsequent injury. 29.2% (21/76) of players were not able to return to professional basketball after the season in which the injury was sustained; however, those who were able to return to the same level of play did not see a significant change in performance as measured by ppg, apg, spg, or bpg when comparing the season prior to the injury and either one or two years after the injury. Stress injuries to the foot carried the worst prognosis, 57.1% (12/21) of those unable to return to professional basketball sustained such an injury. Conclusion: While not extremely common in NBA players, lower extremity bony stress injuries may be career-ending. However, if they are able to return to the NBA following this injury, then their level of play should return to their pre-injury level.

Estimation of Blood Flow Rates in Large Microvascular Networks

PubMed Central

Fry, Brendan C.; Lee, Jack; Smith, Nicolas P.; Secomb, Timothy W.

2012-01-01

Objective Recent methods for imaging microvascular structures provide geometrical data on networks containing thousands of segments. Prediction of functional properties, such as solute transport, requires information on blood flow rates also, but experimental measurement of many individual flows is difficult. Here, a method is presented for estimating flow rates in a microvascular network based on incomplete information on the flows in the boundary segments that feed and drain the network. Methods With incomplete boundary data, the equations governing blood flow form an underdetermined linear system. An algorithm was developed that uses independent information about the distribution of wall shear stresses and pressures in microvessels to resolve this indeterminacy, by minimizing the deviation of pressures and wall shear stresses from target values. Results The algorithm was tested using previously obtained experimental flow data from four microvascular networks in the rat mesentery. With two or three prescribed boundary conditions, predicted flows showed relatively small errors in most segments and fewer than 10% incorrect flow directions on average. Conclusions The proposed method can be used to estimate flow rates in microvascular networks, based on incomplete boundary data and provides a basis for deducing functional properties of microvessel networks. PMID:22506980

Brace related stress in scoliosis patients – Comparison of different concepts of bracing

PubMed Central

Weiss, Hans-Rudolf; Werkmann, Mario; Stephan, Carola

2007-01-01

Background The BSSQbrace questionnaire has been shown to be reliable with good internal consistency and reproducibility estimating the stress scoliosis patients have whilst wearing their brace. Eight questions are provided focussing on this topic. A max. score of 24 can be achieved (from 0 for most stress to 24 for no stress). The subdivision of the score values is: 0–8 (strong stress), 9–16 (medium stress) and 17–24 (little stress). Study design Two BSSQbrace questionnaires have been posted to 65 patients under brace treatment from our Cheneau light data base. All patients had another kind of brace prior to the Cheneau light. The patients have been asked to rate their stress level using one questionnaire for the current brace and the other for the previous one. Results 63 Patients (59 girls and 4 boys) returned their fully completed questionnaires (average age 13,6 years, average Cobb angle 43,7 degrees). Stress level in the previous brace was 11,04 and in the Cheneau light(r) 13,87. The differences were highly significant in the t-test; t = -4,67; p < 0,001. Conclusion The use of the Cheneau light® brace leads to reduced stress and/or impairment for the patients under treatment compared to heavier brace models used so far. PMID:17708766

Tool life and surface integrity aspects when drilling nickel alloy

NASA Astrophysics Data System (ADS)

Kannan, S.; Pervaiz, S.; Vincent, S.; Karthikeyan, R.

2018-04-01

Nickel based super alloys manufactured through powder metallurgy (PM) route are required to increase the operational efficiency of gas turbine engines. They are material of choice for high pressure components due to their superior high temperature strength, excellent corrosion, oxidation and creep resistance. This unique combination of mechanical and thermal properties makes them even more difficult-to-machine. In this paper, the hole making process using coated carbide inserts by drilling and plunge milling for a nickel-based powder metallurgy super alloy has been investigated. Tool life and process capability studies were conducted using optimized process parameters using high pressure coolants. The experimental trials were directed towards an assessment of the tendency for surface malformations and detrimental residual stress profiles. Residual stresses in both the radial and circumferential directions have been evaluated as a function of depth from the machined surface using the target strain gauge / center hole drilling method. Circumferential stresses near workpiece surface and at depth of 512 µm in the starting material was primarily circumferential compression which was measured to be average of –404 MPa. However, the radial stresses near workpiece surface was tensile and transformed to be compressive in nature at depth of 512 µm in the starting material (average: -87 Mpa). The magnitude and the depth below the machined surface in both radial and circumferential directions were primarily tensile in nature which increased with hole number due to a rise of temperature at the tool–workpiece interface with increasing tool wear. These profiles are of critical importance for the selection of cutting strategies to ensure avoidance/minimization of tensile residual stresses that can be detrimental to the fatigue performance of the components. These results clearly show a tendency for the circumferential stresses to be more tensile than the radial stresses. Overall the results indicate that the effect of drilling and milling parameters is most marked in terms of surface quality in the circumferential direction. Material removal rates and tool flank wear must be maintained within the control limits to maintain hole integrity.

Relationship between large slip area and static stress drop of aftershocks of inland earthquake :Example of the 2007 Noto Hanto earthquake

NASA Astrophysics Data System (ADS)

Urano, S.; Hiramatsu, Y.; Yamada, T.

2013-12-01

The 2007 Noto Hanto earthquake (MJMA 6.9; hereafter referred to the main shock) occurred at 0:41(UTC) on March 25, 2007 at a depth of 11km beneath the west coast of Noto Peninsula, central Japan. The dominant slip of the main shock was on a reverse fault with a right-lateral slip and the large slip area was distributed from hypocenter to the shallow part on the fault plane (Horikawa, 2008). The aftershocks are distributed not only in the small slip area but also in the large slip area (Hiramatsu et al., 2011). In this study, we estimate static stress drops of aftershocks on the fault plane of the main shock. We discuss the relationship between the static stress drops of the aftershocks and the large slip area of the main shock by investigating spatial pattern of the values of the static stress drops. We use the waveform data obtained by the group for the joint aftershock observations of the 2007 Noto Hanto Earthquake (Sakai et al., 2007). The sampling frequency of the waveform data is 100 Hz or 200 Hz. Focusing on similar aftershocks reported by Hiramatsu et al. (2011), we analyze static stress drops by using the method of empirical Green's function (EGF) (Hough, 1997) as follows. The smallest earthquake (MJMA≥2.0) of each group of similar earthquakes is set to the EGF earthquake, and the largest earthquake (MJMA≥2.5) is set to the target earthquake. We then deconvolve the waveform of an interested earthquake with that of the EGF earthquake at each station and obtain the spectral ratio of the sources that cancels the propagation effects (path and site effects). Following the procedure of Yamada et al. (2010), we finally estimate static stress drops for P- and S-waves from corner frequencies of the spectral ratio by using a model of Madariaga (1976). The estimated average value of static stress drop is 8.2×1.3 MPa (8.6×2.2 MPa for P-wave and 7.8×1.3 MPa for S-wave). These values are coincident approximately with the static stress drop of aftershocks of other inland earthquakes in Japan (Ito et al., 2005; Iio et al., 2006) and independent of the seismic moment. We then compare the values with the coseismic slip distribution of the main shock reported by Horikawa (2008). If we define large slip areas as areas with a slip exceeding 1 m, the average value of static stress drop is 12×2.3 (MPa) in the area. On the other hand, the average value is 5.7×0.9 (MPa) outside the large slip area. These results suggest that aftershocks in the large slip area likely have larger values of static stress drop, which would reflect the spatial heterogeneity of shear strength and dynamic stress level. Our results are coincident with the result of Yamada et al. (2010).

12 CFR 46.3 - Applicability.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE TREASURY ANNUAL STRESS TEST § 46.3 Applicability... Report used in the calculation of the average. (b) First stress test for covered institutions subject to stress testing requirements as of October 9, 2012. (1) A national bank or Federal savings association...

12 CFR 46.3 - Applicability.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE TREASURY ANNUAL STRESS TEST § 46.3 Applicability... Report used in the calculation of the average. (b) First stress test for covered institutions subject to stress testing requirements as of October 9, 2012. (1) A national bank or Federal savings association...

A data fusion-based drought index

NASA Astrophysics Data System (ADS)

Azmi, Mohammad; Rüdiger, Christoph; Walker, Jeffrey P.

2016-03-01

Drought and water stress monitoring plays an important role in the management of water resources, especially during periods of extreme climate conditions. Here, a data fusion-based drought index (DFDI) has been developed and analyzed for three different locations of varying land use and climate regimes in Australia. The proposed index comprehensively considers all types of drought through a selection of indices and proxies associated with each drought type. In deriving the proposed index, weekly data from three different data sources (OzFlux Network, Asia-Pacific Water Monitor, and MODIS-Terra satellite) were employed to first derive commonly used individual standardized drought indices (SDIs), which were then grouped using an advanced clustering method. Next, three different multivariate methods (principal component analysis, factor analysis, and independent component analysis) were utilized to aggregate the SDIs located within each group. For the two clusters in which the grouped SDIs best reflected the water availability and vegetation conditions, the variables were aggregated based on an averaging between the standardized first principal components of the different multivariate methods. Then, considering those two aggregated indices as well as the classifications of months (dry/wet months and active/non-active months), the proposed DFDI was developed. Finally, the symbolic regression method was used to derive mathematical equations for the proposed DFDI. The results presented here show that the proposed index has revealed new aspects in water stress monitoring which previous indices were not able to, by simultaneously considering both hydrometeorological and ecological concepts to define the real water stress of the study areas.

Averaging problem in general relativity, macroscopic gravity and using Einstein's equations in cosmology.

NASA Astrophysics Data System (ADS)

Zalaletdinov, R. M.

1998-04-01

The averaging problem in general relativity is briefly discussed. A new setting of the problem as that of macroscopic description of gravitation is proposed. A covariant space-time averaging procedure is described. The structure of the geometry of macroscopic space-time, which follows from averaging Cartan's structure equations, is described and the correlation tensors present in the theory are discussed. The macroscopic field equations (averaged Einstein's equations) derived in the framework of the approach are presented and their structure is analysed. The correspondence principle for macroscopic gravity is formulated and a definition of the stress-energy tensor for the macroscopic gravitational field is proposed. It is shown that the physical meaning of using Einstein's equations with a hydrodynamic stress-energy tensor in looking for cosmological models means neglecting all gravitational field correlations. The system of macroscopic gravity equations to be solved when the correlations are taken into consideration is given and described.

Stress field modelling from digital geological map data

NASA Astrophysics Data System (ADS)

Albert, Gáspár; Barancsuk, Ádám; Szentpéteri, Krisztián

2016-04-01

To create a model for the lithospheric stress a functional geodatabase is required which contains spatial and geodynamic parameters. A digital structural-geological map is a geodatabase, which usually contains enough attributes to create a stress field model. Such a model is not accurate enough for engineering-geological purposes because simplifications are always present in a map, but in many cases maps are the only sources for a tectonic analysis. The here presented method is designed for field geologist, who are interested to see the possible realization of the stress field over the area, on which they are working. This study presents an application which can produce a map of 3D stress vectors from a kml-file. The core application logic is implemented on top of a spatially aware relational database management system. This allows rapid and geographically accurate analysis of the imported geological features, taking advantage of standardized spatial algorithms and indexing. After pre-processing the map features in a GIS, according to the Type-Property-Orientation naming system, which was described in a previous study (Albert et al. 2014), the first stage of the algorithm generates an irregularly spaced point cloud by emitting a pattern of points within a user-defined buffer zone around each feature. For each point generated, a component-wise approximation of the tensor field at the point's position is computed, derived from the original feature's geodynamic properties. In a second stage a weighted moving average method calculates the stress vectors in a regular grid. Results can be exported as geospatial data for further analysis or cartographic visualization. Computation of the tensor field's components is based on the implementation of the Mohr diagram of a compressional model, which uses a Coulomb fracture criterion. Using a general assumption that the main principal stress must be greater than the stress from the overburden, the differential stress is calculated from the fracture criterion. The calculation includes the gravitational acceleration, the average density of rocks and the experimental 60 degree of the fracture angle from the normal of the fault plane. This way, the stress tensors are calculated as absolute pressure values per square meters on both sides of the faults. If the stress from the overburden is greater than 1 bar (i.e. the faults are buried), a confined compression would be present. Modelling this state of stress may result a confusing pattern of vectors, because in a confined position the horizontal stress vectors may point towards structures primarily associated with extension. To step over this, and to highlight the variability in the stress-field, the model calculates the vectors directly from the differential stress (practically subtracting the minimum principal stress from the critical stress). The result of the modelling is a vector map, which theoretically represents the minimum tectonic pressure in the moment, when the rock body breaks from an initial state. This map - together with the original fault-map - is suitable for determining those areas where unrevealed tectonic, sedimentary and lithological structures are possibly present (e.g. faults, sub-basins and intrusions). With modelling different deformational phases on the same area, change of the stress vectors can be detected which reveals not only the varying directions of the principal stresses, but the tectonic-driven sedimentation patterns too. The decrease of necessary critical stress in the case of a possible reactivation of a fault in subsequent deformation phase can be managed with the down-ranking of the concerning structural elements. Reference: Albert G., Ungvári ZS., Szentpéteri K. 2014: Modeling the present day stress field of the Pannonian Basin from neotectonic maps - In: Beqiraj A, Ionescu C, Christofides G, Uta A, Beqiraj Goga E, Marku S (eds.) Proceedings XX Congress of the Carpathian-Balkan Geological Association. Tirana: p. 2.

Numerical analysis of Venous External Scaffolding Technology for Saphenous Vein Grafts.

PubMed

Meirson, T; Orion, E; Avrahami, I

2015-07-16

This paper presents a method for analyzing and comparing numerically Saphenous Vein Grafts (SVGs) following Coronary Artery Bypass Graft surgery (CABG). The method analyses the flow dynamics inside vein grafts with and without supporting using Venous External Scaffolding Technology (VEST). The numerical method uses patients׳ specific computational fluid dynamics (CFD) methods to characterize the relevant hemodynamic parameters of patients׳ SVGs. The method was used to compare the hemodynamics of six patient׳s specific model and flow conditions of stented and non-stented SVGs, 12 months post-transplantation. The flow parameters used to characterize the grafts׳ hemodynamics include Time Averaged Wall Shear Stress (TAWSS), Oscillatory Shear Index (OSI) and Relative Residence Time (RRT). The effect of stenting was clearly demonstrated by the chosen parameters. SVGs under constriction of VEST were associated with similar spatial average of TAWSS (10.73 vs 10.29 dyn/cm(2)), yet had fewer lesions with low TAWSS, lower OSI (0.041 vs 0.08) and RRT (0.12 vs 0.24), and more uniform flow with less flow discrepancies. In conclusion, the suggested method and parameters well demonstrated the advantage of VEST support. Stenting vein grafts with VEST improved hemodynamic factors which are correlated to graft failure following CABG procedure. Copyright © 2015 Elsevier Ltd. All rights reserved.

Compassion satisfaction, burnout, and secondary traumatic stress in heart and vascular nurses.

PubMed

Young, Jennifer L; Derr, Denise M; Cicchillo, Vikki J; Bressler, Sonya

2011-01-01

Objectives for this project were to determine the prevalence of compassion satisfaction (CS), burnout, and secondary traumatic stress (STS) in heart and vascular nurses to confirm whether differences exist between intensive care and intermediate care nurses. The Professional Quality of Life Scale Compassion Satisfaction and Compassion Fatigue: Version 5 developed by Stamm (2009) was used. Results showed that nurses who work in the heart and vascular intermediate care unit had average to high scores of CS, low to average levels of burnout, and low to average levels of STS. Nurses who work in the heart and vascular intensive care unit had average to high levels of CS, low to average levels of burnout, and low to average levels of STS. These findings suggest that leadership should be aware of the prevalence of STS and burnout in heart and vascular nurses. Raising awareness of STS and burnout in intensive care and intermediate care nurses can help in targeting more specific strategies that may prevent the onset of developing these symptoms.

T wave alternans during exercise and atrial pacing in humans

NASA Technical Reports Server (NTRS)

Hohnloser, S. H.; Klingenheben, T.; Zabel, M.; Li, Y. G.; Albrecht, P.; Cohen, R. J.

1997-01-01

INTRODUCTION: Evidence is accumulating that microvolt T wave alternans (TWA) is a marker of increased risk for ventricular tachyarrhythmias. Initially, atrial pacing was used to elevate heart rate and elicit TWA. More recently, a noninvasive approach has been developed that elevates heart rate using exercise. METHODS AND RESULTS: In 30 consecutive patients with a history of ventricular tachyarrhythmias, the spectral method was used to detect TWA during both atrial pacing and submaximal exercise testing. The concordance rate for the presence or absence of TWA using the two measurement methods was 84%. There was a patient-specific heart rate threshold for the detection of TWA that averaged 100 +/- 14 beats/min during exercise compared with 97 +/- 9 beats/min during right atrial pacing (P = NS). Beyond this threshold, there was a significant and comparable increase in level of TWA with decreasing pacing cycle length and increasing exercise heart rates. CONCLUSIONS: The present study is the first to demonstrate that microvolt TWA can be assessed reliably and noninvasively during exercise stress. There is a patient-specific heart rate threshold beyond which TWA continues to increase with increasing heart rates. Heart rate thresholds for the onset of TWA measured during atrial pacing and exercise stress were comparable, indicating that heart rate alone appears to be the main factor of determining the onset of TWA during submaximal exercise stress.

46 CFR 52.01-95 - Design (modifies PG-16 through PG-31 and PG-100).

Code of Federal Regulations, 2010 CFR

2010-10-01

... exceeding 525 °F. Refer to § 56.30-30(b)(1) of this subchapter for applicable requirements. (e) Stresses. (Modifies PG-22.) The stresses due to hydrostatic head shall be taken into account in determining the... stresses, imposed by effects other than internal pressure or static head, which increase the average stress...

46 CFR 52.01-95 - Design (modifies PG-16 through PG-31 and PG-100).

Code of Federal Regulations, 2012 CFR

2012-10-01

... exceeding 525 °F. Refer to § 56.30-30(b)(1) of this subchapter for applicable requirements. (e) Stresses. (Modifies PG-22.) The stresses due to hydrostatic head shall be taken into account in determining the... stresses, imposed by effects other than internal pressure or static head, which increase the average stress...

46 CFR 52.01-95 - Design (modifies PG-16 through PG-31 and PG-100).

Code of Federal Regulations, 2011 CFR

2011-10-01

... exceeding 525 °F. Refer to § 56.30-30(b)(1) of this subchapter for applicable requirements. (e) Stresses. (Modifies PG-22.) The stresses due to hydrostatic head shall be taken into account in determining the... stresses, imposed by effects other than internal pressure or static head, which increase the average stress...

[Modeling employee stress in psychiatric rehabilitation--effects of personal and organizational factors].

PubMed

Queri, S; Konrad, M; Keller, K

2012-08-01

Increasing stress-associated health problems in Germany often are attributed to problems on the job, in particular to rising work demands. The study includes several stress predictors from other results and from literature in one predictive model for the field of work of "psychiatric rehabilitation".A cross-sectional design was used to measure personal and organizational variables with quantitative standard questionnaires as self-ratings from n=243 pedagogically active employees from various professions. Overall stress and job stress were measured with different instruments.The sample showed above-average overall stress scores along with below-average job stress scores. The multivariate predictive model for explaining the heightened stress shows pathogenetic and salutogenetic main effects for organizational variables such as "gratification crisis" and personal variables such as "occupational self-efficacy expectations" as well as an interaction of both types of variables. There are relevant gender-specific results concerning empathy and differences between professions concerning the extent of occupational self-efficacy.The results are a matter of particular interest for the practice of workplace health promotion as well as for social work schools, the main group in our sample being social workers. © Georg Thieme Verlag KG Stuttgart · New York.

Couples coping with stress: Between-person differences and within-person processes.

PubMed

Hilpert, Peter; Xu, Feng; Milek, Anne; Atkins, David C; Bodenmann, Guy; Bradbury, Thomas N

2018-04-01

In intimate relationships, spousal support (or dyadic coping) can directly benefit relationships (i.e., direct effect) and protect the relationship against the negative spillover effects of stress (i.e., buffer effect). As stress-coping theories suggest, both processes can vary between persons as well as within persons. However, empirically, this distinction is not always made explicit, resulting in potentially misleading conclusions about dyadic stress-coping processes. In the current study, we investigated stress and coping processes in couples at both between- and within-person levels. Participants were 84 Chinese dual-earning couples (N = 168 individuals) participated in a 7-day diary study. Between persons, our multilevel analyses replicated well-established buffering effects: The link between average stress and relationship outcomes was reduced if the partner provided more support on average. Within persons, results implied a significant buffer effect only in women; their relationship satisfaction was highest on days when they experienced higher levels of stress and higher levels of partner support. The present findings demonstrate how distinguishing between- and within-person effects can provide a better conceptual understanding of dyadic processes in intimate relationships while examining stress-coping associations in an understudied group. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

EEG changes as heat stress reactions in rats irradiated by high intensity 35 GHz millimeter waves.

PubMed

Xie, Taorong; Pei, Jian; Cui, Yibin; Zhang, Jie; Qi, Hongxing; Chen, Shude; Qiao, Dengjiang

2011-06-01

As the application of millimeter waves for civilian and military use increases, the possibility of overexposure to millimeter waves will also increase. This paper attempts to evaluate stress reactions evoked by 35 GHz millimeter waves. The stress reactions in Sprague-Dawley (SD) rats were quantitatively studied by analyzing electroencephalogram (EEG) changes induced by overexposure to 35 GHz millimeter waves. The relative changes in average energy of the EEG and its wavelet decompositions were used for extracting the stress reaction indicators. Incident average power densities (IAPDs) of 35 GHz millimeter waves from 0.5 W cm(-2) to 7.5 W cm(-2) were employed to investigate the relation between irradiation dose and the stress reactions in the rats. Different stress reaction periods evoked by irradiation were quantitatively evaluated by EEG results. The results illustrate that stress reactions are more intense during the first part of the irradiation than during the later part. The skin temperature increase produced by millimeter wave irradiation is the principle reason for stress reactions and skin injuries. As expected, at the higher levels of irradiation, the reaction time decreases and the reaction intensity increases.

A new approach to assess the skier additional stress within a multi-layered snowpack

NASA Astrophysics Data System (ADS)

Monti, Fabiano; Gaume, Johan; van Herwijnen, Alec; Schweizer, Jürg

2014-05-01

The physical and mechanical processes of dry-snow slab avalanche formation can be distinguished into two subsequent phases: failure initiation and crack propagation. Several approaches tried to quantify slab avalanche release probability in terms of failure initiation, based on a simple strength-of-material approach (strength vs. stress). Even if it is known that both weak layer and slab properties play a major role in avalanche release, apart from weak layer characteristics, often only the slab thickness and its average density were considered. For calculating the amount of additional stress (e.g. due to a skier) at the depth of the weak layer, the snow cover was often assumed to be a semi-infinite elastic half space in order to apply Boussinesq's theory. However, finite element (FE) calculations have shown that slab layering strongly influences the stress at depth. To avoid FE calculations, we suggest a new approach based on a simplification of multi-layered elasticity theory. It allows computing the additional stress due to a skier at the depth of the weak layer, taking into account the layering of the snow slab and the substratum. The proposed approach was first tested on simplified snow profiles and compared reasonably well with FE calculations. We then implemented the method to refine the classical skier stability index. Using manually observed snow profiles, classified in different stability classes using stability tests, we obtained a satisfactory discrimination power. Lastly, the refined skier stability index was implemented into the 1-D snow cover model SNOWPACK and presented on two case studies. In the future, it will be interesting to implement the proposed method for describing skier-induced stress within a multi-layered snowpack into more complex models which take into account not only failure initiation but also crack propagation.

Time-dependent reliability analysis of ceramic engine components

NASA Technical Reports Server (NTRS)

Nemeth, Noel N.

1993-01-01

The computer program CARES/LIFE calculates the time-dependent reliability of monolithic ceramic components subjected to thermomechanical and/or proof test loading. This program is an extension of the CARES (Ceramics Analysis and Reliability Evaluation of Structures) computer program. CARES/LIFE accounts for the phenomenon of subcritical crack growth (SCG) by utilizing either the power or Paris law relations. The two-parameter Weibull cumulative distribution function is used to characterize the variation in component strength. The effects of multiaxial stresses are modeled using either the principle of independent action (PIA), the Weibull normal stress averaging method (NSA), or the Batdorf theory. Inert strength and fatigue parameters are estimated from rupture strength data of naturally flawed specimens loaded in static, dynamic, or cyclic fatigue. Two example problems demonstrating proof testing and fatigue parameter estimation are given.

Favre-Averaged Turbulence Statistics in Variable Density Mixing of Buoyant Jets

NASA Astrophysics Data System (ADS)

Charonko, John; Prestridge, Kathy

2014-11-01

Variable density mixing of a heavy fluid jet with lower density ambient fluid in a subsonic wind tunnel was experimentally studied using Particle Image Velocimetry and Planar Laser Induced Fluorescence to simultaneously measure velocity and density. Flows involving the mixing of fluids with large density ratios are important in a range of physical problems including atmospheric and oceanic flows, industrial processes, and inertial confinement fusion. Here we focus on buoyant jets with coflow. Results from two different Atwood numbers, 0.1 (Boussinesq limit) and 0.6 (non-Boussinesq case), reveal that buoyancy is important for most of the turbulent quantities measured. Statistical characteristics of the mixing important for modeling these flows such as the PDFs of density and density gradients, turbulent kinetic energy, Favre averaged Reynolds stress, turbulent mass flux velocity, density-specific volume correlation, and density power spectra were also examined and compared with previous direct numerical simulations. Additionally, a method for directly estimating Reynolds-averaged velocity statistics on a per-pixel basis is extended to Favre-averages, yielding improved accuracy and spatial resolution as compared to traditional post-processing of velocity and density fields.

Performance Under Stress Conditions During Multidisciplinary Team Immersive Pediatric Simulations.

PubMed

Ghazali, Daniel Aiham; Darmian-Rafei, Ivan; Ragot, Stéphanie; Oriot, Denis

2018-06-01

The primary objective was to determine whether technical and nontechnical performances were in some way correlated during immersive simulation. Performance was measured among French Emergency Medical Service workers at an individual and a team level. Secondary objectives were to assess stress response through collection of physiologic markers (salivary cortisol, heart rate, the proportion derived by dividing the number of interval differences of successive normal-to-normal intervals > 50 ms by the total number of normal-to-normal intervals [pNN50], low- and high-frequency ratio) and affective data (self-reported stress, confidence, and dissatisfaction), and to correlate them to performance scores. Prospective observational study performed as part of a larger randomized controlled trial. Medical simulation laboratory. Forty-eight participants distributed among 12 Emergency Medical System teams. Individual and team performance measures and individual stress response were assessed during a high-fidelity simulation. Technical performance was assessed by the intraosseous access performance scale and the Team Average Performance Assessment Scale; nontechnical performance by the Behavioral Assessment Tool for leaders, and the Clinical Teamwork Scale. Stress markers (salivary cortisol, heart rate, pNN50, low- and high-frequency ratio) were measured both before (T1) and after the session (T2). Participants self-reported stress before and during the simulation, self-confidence, and perception of dissatisfaction with team performance, rated on a scale from 0 to 10. Scores (out of 100 total points, mean ± SD) were intraosseous equals to 65.6 ± 14.4, Team Average Performance Assessment Scale equals to 44.6 ± 18.1, Behavioral Assessment Tool equals to 49.5 ± 22.0, Clinical Teamwork Scale equals to 50.3 ± 18.5. There was a strong correlation between Behavioral Assessment Tool and Clinical Teamwork Scale (Rho = 0.97; p = 0.001), and Behavioral Assessment Tool and Team Average Performance Assessment Scale (Rho = 0.73; p = 0.02). From T1 to T2, all stress markers (salivary cortisol, heart rate, pNN50, and low- and high-frequency ratio) displayed an increase in stress level (p < 0.001 for all). Self-confidence was positively correlated with performance (Clinical Teamwork Scale: Rho = 0.47; p = 0.001, Team Average Performance Assessment Scale: Rho = 0.46; p = 0.001). Dissatisfaction was negatively correlated with performance (Rho = -0.49; p = 0.0008 with Behavioral Assessment Tool, Rho = -0.47; p = 0.001 with Clinical Teamwork Scale, Rho = -0.51; p = 0.0004 with Team Average Performance Assessment Scale). No correlation between stress response and performance was found. There was a positive correlation between leader (Behavioral Assessment Tool) and team (Clinical Teamwork Scale and Team Average Performance Assessment Scale) performances. These performance scores were positively correlated with self-confidence and negatively correlated with dissatisfaction.

The Dementia Services Mini-Screen: A Simple Method to Identify Patients and Caregivers Needing Enhanced Dementia Care Services

PubMed Central

Borson, Soo; Scanlan, James M.; Sadak, Tatiana; Lessig, Mary; Vitaliano, Peter

2014-01-01

Objective The National Alzheimer’s Plan calls for targeted health system change to improve outcomes for persons with dementia and their family caregivers. We explored whether dementia-specific service needs and gaps could be predicted from simple information that can be readily acquired in routine medical care settings. Method Primary family caregivers for cognitively impaired older adults (n=215) were asked about current stress, challenging patient behaviors, and prior-year needs and gaps in 16 medical and psychosocial services. Demographic data, caregiver stress, and patient clinical features were evaluated in regression analyses to identify unique predictors of service needs and gaps. Results Caregiver stress and patient behavior problems together accounted for an average of 24% of the whole-sample variance in total needs and gaps. Across all analyses, including total, medical, and psychosocial services needs and gaps, all other variables combined (comorbid chronic disease, dementia severity, age, caregiver relationship, and residence) accounted for an accounted for a mean of 3%, with no variable yielding more than 4% in any equation. We combined stress and behavior problem indicators into a simple screen. In early/mild dementia dyads (n=111) typical in primary care settings, the screen identified gaps in total and psychosocial care in 84% and 77%, respectively, of those with high stress/high behavior problems vs. 25% and 23%, respectively, of those with low stress/low behavior problems. Medical care gaps were dramatically higher in high stress/high behavior problem dyads (66%) than all others (12%). Conclusion A simple tool (likely completed in 1–2 minutes) which combines caregiver stress and patient behavior problems, the Dementia Services Mini-Screen, could help clinicians rapidly identify high need, high gap dyads. Health care systems could use it to estimate population needs for targeted dementia services and facilitate their development. PMID:24315560

Should fertilization treatment start with reducing stress?

PubMed

Campagne, Daniel M

2006-07-01

In the past few decades, new and more efficient techniques to help solve fertility problems have become widely available throughout the developed world. These techniques include hormonal stimulation, ICSI, gamete intra-Fallopian transfer (GIFT) and IVF, and their cost is, on average, considerable. There is substantial initial evidence that the psychological disposition of the parents-to-be influences their fertility and thus the outcome of fertilization techniques. Many fertility treatments include consultation with a psychologist and do try to keep the stress produced by the treatment itself to a minimum, using concurrent therapy. However, the accumulating evidence points to the need to program medical fertility treatment, bearing in mind both chronic and acute stress levels, and to treat for their reduction before commencing the (actual) fertility treatment. There is ample evidence that lower stress levels mean better female and male natural fertility, though there is as yet no conclusive experimental evidence that lower stress levels result in better fertility treatment outcome. However, first reducing stress may diminish the number of treatment cycles needed before pregnancy is obtained, may prepare the couple for an initial failure of treatment or even make the more invasive techniques unnecessary. Primary psychological treatment for trait and state stress, being a less invasive method than IVF, ICSI or GIFT, is to be applied whenever indicated. Also, treatment and therapy to reduce stress, and in so doing enhance fertility, do not provoke the ethical and religious objections raised by infertility treatments.

Management of heat stress in the livestock industry

USDA-ARS?s Scientific Manuscript database

Heat stress costs the animal industry over $1.7 billion annually. Annual losses average $369 million in the beef cattle industry and $299 million in the swine industry. The impacts of a single heat stress event on individual animals are quite varied. Brief events often cause little or no effect. ...

Primary caregivers of in-home oxygen-dependent children: predictors of stress based on characteristics, needs and social support.

PubMed

Wang, Kai-Wei K; Lin, Hung-Ching; Lee, Chin-Ting; Lee, Kuo-Sheng

2016-07-01

To identify the predictors of primary caregivers' stress in caring for in-home oxygen-dependent children by examining the association between their levels of stress, caregiver needs and social support. Increasing numbers of primary caregivers of oxygen-dependent children experience caregiving stress that warrants investigation. The study used a cross-sectional design with three psychometric scales - Modified-Parenting Stress Index, Caregiver Needs Scale and Social Support Index. The data collected during 2010-2011 were from participants who were responsible for their child's care that included oxygen therapy for ≧6 hours/day; the children's ages ranged from 3 months-16 years. Descriptive statistics and multivariable linear regression were used. A total of 104 participants (M = 34, F = 70) were recruited, with an average age of 39·7 years. The average age of the oxygen-dependent children was 6·68 years and their daily use of oxygen averaged 11·39 hours. The caregivers' overall levels of stress were scored as high and information needs were scored as the highest. The most available support from family and friends was emotional support. Informational support was mostly received from health professionals, but both instrumental and emotional support were important. Levels of stress and caregiver needs were significantly correlated. Multivariable linear regression analyses identified three risk factors predicting stress, namely, the caregiver's poor health status, the child's male gender and the caregiver's greater financial need. To support these caregivers, health professionals can maintain their health status and provide instrumental, emotional, informational and financial support. © 2016 John Wiley & Sons Ltd.

Quantify patient-specific coronary material property and its impact on stress/strain calculations using in vivo IVUS data and 3D FSI models: a pilot study

PubMed Central

Guo, Xiaoya; Zhu, Jian; Maehara, Akiko; Monoly, David; Samady, Habib; Wang, Liang; Billiar, Kristen L.; Zheng, Jie; Yang, Chun; Mintz, Gary S.; Giddens, Don P.; Tang, Dalin

2016-01-01

Computational models have been used to calculate plaque stress and strain for plaque progression and rupture investigations. An intravascular ultrasound (IVUS)-based modeling approach is proposed to quantify in vivo vessel material properties for more accurate stress/strain calculations. In vivo Cine IVUS and VH-IVUS coronary plaque data were acquired from one patient with informed consent obtained. Cine IVUS data and 3D thin-slice models with axial stretch were used to determine patient-specific vessel material properties. Twenty full 3D fluid–structure interaction models with ex vivo and in vivo material properties and various axial and circumferential shrink combinations were constructed to investigate the material stiffness impact on stress/strain calculations. The approximate circumferential Young’s modulus over stretch ratio interval [1.0, 1.1] for an ex vivo human plaque sample and two slices (S6 and S18) from our IVUS data were 1631, 641, and 346 kPa, respectively. Average lumen stress/strain values from models using ex vivo, S6 and S18 materials with 5 % axial shrink and proper circumferential shrink were 72.76, 81.37, 101.84 kPa and 0.0668, 0.1046, and 0.1489, respectively. The average cap strain values from S18 material models were 150–180 % higher than those from the ex vivo material models. The corresponding percentages for the average cap stress values were 50–75 %. Dropping axial and circumferential shrink consideration led to stress and strain over-estimations. In vivo vessel material properties may be considerably softer than those from ex vivo data. Material stiffness variations may cause 50–75 % stress and 150–180 % strain variations. PMID:27561649

“The Cough Game”: Are there characteristic urethrovesical movement patterns associated with stress incontinence?

PubMed Central

LEWICKY-GAUPP, Christina; BLAIVAS, Jerry; CLARK, Amanda; McGUIRE, Edward J.; SCHAER, Gabriel; TUMBARELLO, Julie; TUNN, Ralf; DeLANCEY, John O.L.

2009-01-01

Introduction and Hypothesis To determine if 5 experts in female stress urinary incontinence (SUI) could discover a pattern of urethrovesical movement characteristic of SUI on dynamic perineal ultrasound. Methods A secondary analysis of data from a case-control study was performed. Ultrasounds from 31 cases (daily SUI) and 42 controls (continent volunteers) of similar age and parity were analyzed. Perineal ultrasound was performed during a single cough. The 5 experts, blinded to continence status and urodynamics, classified each woman as stress continent or incontinent. Results Correct responses ranged from 45.7% to 65.8% (mean 57.4 ± 7.6). Sensitivity was 53.0 ± 8.8% and specificity 61.2 ± 12.4%. The positive predictive value was 48.8 ± 8.2% and negative predictive value was 65.0 ± 7.3%. Inter-rater reliability, evaluated by Cohen's kappa statistic, averaged 0.47 [95% CI 0.40 – 0.50]. Conclusions Experts could not identify a pattern of urethrovesical movement characteristic of SUI on ultrasound. PMID:18850057

Fabrication and Probabilistic Fracture Strength Prediction of High-Aspect-Ratio Single Crystal Silicon Carbide Microspecimens With Stress Concentration

NASA Technical Reports Server (NTRS)

Nemeth, Noel N.; Evans, Laura J.; Jadaan, Osama M.; Sharpe, William N., Jr.; Beheim, Glenn M.; Trapp, Mark A.

2005-01-01

Single crystal silicon carbide micro-sized tensile specimens were fabricated with deep reactive ion etching (DRIE) in order to investigate the effect of stress concentration on the room-temperature fracture strength. The fracture strength was defined as the level of stress at the highest stressed location in the structure at the instant of specimen rupture. Specimens with an elliptical hole, a circular hole, and without a hole (and hence with no stress concentration) were made. The average fracture strength of specimens with a higher stress concentration was larger than the average fracture strength of specimens with a lower stress concentration. Average strength of elliptical-hole, circular-hole, and without-hole specimens was 1.53, 1.26, and 0.66 GPa, respectively. Significant scatter in strength was observed with the Weibull modulus ranging between 2 and 6. No fractographic examination was performed but it was assumed that the strength controlling flaws originated from etching grooves along the specimen side-walls. The increase of observed fracture strength with increasing stress concentration was compared to predictions made with the Weibull stress-integral formulation by using the NASA CARES/Life code. In the analysis isotropic material and fracture behavior was assumed - hence it was not a completely rigorous analysis. However, even with these assumptions good correlation was achieved for the circular-hole specimen data when using the specimen data without stress concentration as a baseline. Strength was over predicted for the elliptical-hole specimen data. Significant specimen-to-specimen dimensional variation existed in the elliptical-hole specimens due to variations in the nickel mask used in the etching. To simulate the additional effect of the dimensional variability on the probabilistic strength response for the single crystal specimens the ANSYS Probabilistic Design System (PDS) was used with CARES/Life.

Nonlinear Viscoelastic Characterization of the Porcine Spinal Cord

PubMed Central

Shetye, Snehal; Troyer, Kevin; Streijger, Femke; Lee, Jae H. T.; Kwon, Brian K.; Cripton, Peter; Puttlitz, Christian M.

2014-01-01

Although quasi-static and quasi-linear viscoelastic properties of the spinal cord have been reported previously, there are no published studies that have investigated the fully (strain-dependent) nonlinear viscoelastic properties of the spinal cord. In this study, stress relaxation experiments and dynamic cycling were performed on six fresh porcine lumbar cord specimens to examine their viscoelastic mechanical properties. The stress relaxation data were fitted to a modified superposition formulation and a novel finite ramp time correction technique was applied. The parameters obtained from this fitting methodology were used to predict the average dynamic cyclic viscoelastic behavior of the porcine cord. The data indicate that the porcine spinal cord exhibited fully nonlinear viscoelastic behavior. The average weighted RMSE for a Heaviside ramp fit was 2.8kPa, which was significantly greater (p < 0.001) than that of the nonlinear (comprehensive viscoelastic characterization (CVC) method) fit (0.365kPa). Further, the nonlinear mechanical parameters obtained were able to accurately predict the dynamic behavior, thus exemplifying the reliability of the obtained nonlinear parameters. These parameters will be important for future studies investigating various damage mechanisms of the spinal cord and studies developing high resolution finite elements models of the spine. PMID:24211612

Biological Rhythms Modelisation of Vigilance and Sleep in Microgravity State with COSINOR and Volterra's Kernels Methods

NASA Astrophysics Data System (ADS)

Gaudeua de Gerlicz, C.; Golding, J. G.; Bobola, Ph.; Moutarde, C.; Naji, S.

2008-06-01

The spaceflight under microgravity cause basically biological and physiological imbalance in human being. Lot of study has been yet release on this topic especially about sleep disturbances and on the circadian rhythms (alternation vigilance-sleep, body, temperature...). Factors like space motion sickness, noise, or excitement can cause severe sleep disturbances. For a stay of longer than four months in space, gradual increases in the planned duration of sleep were reported. [1] The average sleep in orbit was more than 1.5 hours shorter than the during control periods on earth, where sleep averaged 7.9 hours. [2] Alertness and calmness were unregistered yield clear circadian pattern of 24h but with a phase delay of 4h.The calmness showed a biphasic component (12h) mean sleep duration was 6.4 structured by 3-5 non REM/REM cycles. Modelisations of neurophysiologic mechanisms of stress and interactions between various physiological and psychological variables of rhythms have can be yet release with the COSINOR method. [3

Nurses' self-care behaviors related to weight and stress.

PubMed

Nahm, Eun-Shim; Warren, Joan; Zhu, Shijun; An, Minjeong; Brown, Jeanine

2012-01-01

Considerable research on preventive health care behaviors has been conducted in different segments of the population. Although nurses are the largest group of direct health care providers (3 million), little is known about their preventive health care behaviors. As the average age of nurses working in the United States (US) increases (mean age 47 years), maintaining their health to ensure they can continue to provide optimal health care to others becomes a greater priority. This descriptive online study examined registered nurses' dietary and exercise practices, weight status, stress levels, and preferred preventive health strategies using a sample of nurses recruited from a community-based, urban teaching hospital (n = 183; mean age 47 ± 11.3 years). The majority of participants (72.2%, n = 122) reported a lack of exercise, and more than half (53.8%, n = 91) had an irregular meal pattern. The average body mass index (BMI) was 28.3 ± 6.8, and 59.2% (n = 100) were either overweight (n = 47) or obese (n = 53). BMI had a significant inverse relationship with having a regular meal schedule and the amount of time spent exercising. Participants who reported greater stress had more irregular meal schedules. The most frequently used stress-release method was eating (n = 32), followed by exercise (n = 31). Nurses are fully aware of measures that should be taken for healthy living. Their knowledge, however, has not been well translated into their own self-care. As nursing shortages loom, maintaining the health of the aging nursing workforce is essential to retention. Further research is needed to identify factors that may motivate nurses to better care for themselves and measures that can be implemented by employers to initiate and sustain these preventive health care behaviors. Copyright © 2012 Elsevier Inc. All rights reserved.

Speed ratio but cabin temperature positively correlated with increased heart rates among professional drivers during car races.

PubMed

Yanagida, Ryo; Takahashi, Kiichi; Miura, Masaru; Nomura, Masahiro; Ogawa, Yojiro; Aoki, Ken; Iwasaki, Ken-Ichi

2016-11-01

The present study measures heart rate (HR) on a number of professional race-car drivers during actual car races through annual seasons to test hypotheses that faster relative speed and higher cabin temperature would induce higher HR. Heart rates in fifteen male drivers (31.2 ± 5.5 years old) were obtained by chest-strap sensors during official-professional 13 races. Average HR was calculated while the driver was racing from the start to the end of each race. The average HR during races was 164.5 ± 15.1 beats min -1 and the average amount of time each driver spent driving per race was 54.2 ± 13.7 min. Average HR significantly and positively correlated with mean speed ratio (P < 0.001), but not with the average cabin temperatures (P = 0.533, range 25.6-41.8 °C) by the multiple linear regression analysis. Both average HR and mean speed ratio were significantly lower under wet, than dry conditions (151.9 ± 16.5 vs. 168.3 ± 12.5 beats min -1 , 86.9 ± 4.4 vs. 93.4 ± 1.5 %). The cardiovascular system of drivers is considerably stressed at extremely high HR. This high average HR positively correlated with mean speed ratio, suggesting that faster driving speed would induce greater cardiovascular stress to professional drivers during actual races. However, contrary to our hypothesis, cabin temperature was not significantly correlated with average HR. It is speculated that direct body cooling systems used in this professional race category work well against increases in HR by thermal stress under the temperature range found herein.

AN INVERSE MODELING APPROACH FOR STRESS ESTIMATION IN MITRAL VALVE ANTERIOR LEAFLET VALVULOPLASTY FOR IN-VIVO VALVULAR BIOMATERIAL ASSESSMENT

PubMed Central

Lee, Chung-Hao; Amini, Rouzbeh; Gorman, Robert C.; Gorman, Joseph H.; Sacks, Michael S.

2013-01-01

Estimation of regional tissue stresses in the functioning heart valve remains an important goal in our understanding of normal valve function and in developing novel engineered tissue strategies for valvular repair and replacement. Methods to accurately estimate regional tissue stresses are thus needed for this purpose, and in particular to develop accurate, statistically informed means to validate computational models of valve function. Moreover, there exists no currently accepted method to evaluate engineered heart valve tissues and replacement heart valve biomaterials undergoing valvular stresses in blood contact. While we have utilized mitral valve anterior leaflet valvuloplasty as an experimental approach to address this limitation, robust computational techniques to estimate implant stresses are required. In the present study, we developed a novel numerical analysis approach for estimation of the in-vivo stresses of the central region of the mitral valve anterior leaflet (MVAL) delimited by a sonocrystal transducer array. The in-vivo material properties of the MVAL were simulated using an inverse FE modeling approach based on three pseudo-hyperelastic constitutive models: the neo-Hookean, exponential-type isotropic, and full collagen-fiber mapped transversely isotropic models. A series of numerical replications with varying structural configurations were developed by incorporating measured statistical variations in MVAL local preferred fiber directions and fiber splay. These model replications were then used to investigate how known variations in the valve tissue microstructure influence the estimated ROI stresses and its variation at each time point during a cardiac cycle. Simulations were also able to include estimates of the variation in tissue stresses for an individual specimen dataset over the cardiac cycle. Of the three material models, the transversely anisotropic model produced the most accurate results, with ROI averaged stresses at the fully-loaded state of 432.6±46.5 kPa and 241.4±40.5 kPa in the radial and circumferential directions, respectively. We conclude that the present approach can provide robust instantaneous mean and variation estimates of tissue stresses of the central regions of the MVAL. PMID:24275434

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

Nacre, also known as mother-of-pearl, is a biocomposite material that exhibits higher strength and fracture toughness than its component materials. It derives its strength from the brick-and-mortar layering of aragonite (CaCO{sub 3}) platelets and organic binder. It is believed that the protein binder helps redistribute the stress throughout all tablets for optimal mechanical performance. In this study, we attempt to measure the mechanical properties of aragonite within nacre and compare them to bulk aragonite and bulk nacre and understand the redistribution of stresses. Here we show that x-ray diffraction techniques are useful for isolating and measuring strain of crystallites withinmore » a composite material. Our results show that the apparent stiffness of aragonite varies with crystallographic directions and is higher than the stiffness of bulk nacre in all cases, meaning that aragonite tablets are exposed to less than the average bulk stress. The average force applied to the bulk sample is partitioned between the aragonite and the binder, so that the protein layer bears as much as 27.2% of the total applied force. Different crystallographic directions exhibit behaviors different than bulk aragonite or bulk nacre. These are related to texture of aragonite platelets (i.e. preferred orientations within nacre). By examining nacre, we can obtain a better understanding of the mechanical relationship between the ceramic and polymer in composite materials. We expect that x-ray diffraction will become the standard method for probing the mechanical properties of composite materials.« less

Spatiotemporal variations in the b-value of earthquake magnitude-frequency distributions: Classification and causes

NASA Astrophysics Data System (ADS)

El-Isa, Z. H.; Eaton, David W.

2014-03-01

Interpretation of the b-value of earthquake frequency-magnitude distributions has received considerable attention in recent decades. This paper provides a comprehensive review of previous investigations of spatial and temporal variations in b-value, including their classification and possible causes. Based on least-squares regression of seismicity data compiled from the NEIC, IRIS and ISC catalogs, we find an average value of 1.02 ± 0.03 for the whole Earth and its two hemispheres, consistent with the general view that in seismically active regions the long-term average value is close to unity. Nevertheless, wide-ranging b-variations (0.3 ≤ b ≤ 2.5) have been reported in the literature. This variability has been interpreted to arise from one or more of the following factors: prevailing stress state, crustal heterogeneity, focal depth, pore pressure, geothermal gradient, tectonic setting, petrological/environmental/geophysical characteristics, clustering of events, incomplete catalog data, and/or method of calculation. Excluding the latter, all of these factors appear to be linked, directly or indirectly, with the effective state of stress. Although time-dependent changes in b-value are well documented, conflicting observations reveal either a precursory increase or decrease in b value before major earthquakes. Our compilation of published analyses suggests that statistically significant b-variations occur globally on various timescales, including annual, monthly and perhaps diurnal. Taken together, our review suggests that b-variations are most plausibly linked with changes in effective stress.

Effects of chocolate intake on Perceived Stress; a Controlled Clinical Study

PubMed Central

Al Sunni, Ahmed; Latif, Rabia

2014-01-01

Background Cocoa polyphenols have been shown to reduce stress in highly stressed, as well as normal healthy individuals, we wondered whether commercially available chocolate could reduce perceived stress in medical students or not, so we decided to conduct this study. Methods Sixty students were divided into 3 groups (10 males + 10 females/group): i) Dark chocolate (DC) ii) Milk chocolate (MC) iii) White chocolate (WC). Subjects answered a PSS-10 (Perceived Stress Scale) questionnaire at baseline and after consumption of chocolate (40 g/day) for 2 weeks. Data were analyzed by using Microsoft Excel and SPSS version 20. Descriptive analyses were conducted. Means were compared across the study groups by One-Way ANOVA and within the same group by paired ‘t’ test. Results Mean stress scores compared between the groups by ANOVA revealed statistically not significant differences before (F =0.505; P=0.606) and after chocolate consumption (F=0.188; P=0.829). Paired ‘t’ test compared stress scores means before and after chocolate supplementation within the same group and exhibited statistically significant decrease in DC (t = 2.341; p value = 0.03) and MC (t = 3.302; p value = 0.004) groups. Mean stress scores decreased, on average, by approximately 2 and 3 points in DC and MC groups, respectively, at 95% Confidence Interval. The difference was more evident and statistically significant in female students as compared to the males. Conclusion Consumption of 40 g of Dark and Milk chocolate daily during a period of 2 weeks appear to be an effective way to reduce perceived stress in females. PMID:25780358

Analysis of the occupational stress of Korean surgeons: a pilot study

PubMed Central

Kang, Sang-Hee; Lee, Ji-Sung; Ji, Woong-Bae; Yoo, Byoung-Eun; You, Ji-Young

2013-01-01

Purpose Surgeons serve one of the most challenging and stressful professions. Ineffective control of occupational stress leads to burnout of the surgeon. The aim of this study was to obtain preliminary data on the sources and the degree of stress of surgeons and to determine the feasibility of the survey. Methods A total of 63 surgeons in our three affiliated hospitals were enrolled in this study. Fifty-five questions were used to assess the demographics, characteristics and Korean occupational stress scale (KOSS), which were prepared and validated by the National Study for Development and Standardization of Occupational Stress. Results Forty-seven of the 63 surgeons participated in this study (74.6%). The mean KOSS score of the survey was 50.9 ± 8.55, which was significantly higher than that of other professions (P < 0.01). Drinking and smoking habits were not related to the KOSS score. Doing exercise was related to a low KOSS score in terms of low KOSS total score (P < 0.01). Average duty hours (P < 0.01) and night duty days per week (P = 0.01) were strongly related to higher KOSS in the linear regression analysis. Conclusion This is the first study to evaluate job stress of surgeons in Korea. This study showed that Korean Surgeons had higher occupational stress than other Korean professions. A larger study based on this pilot study will help generate objective data for occupational stress of Korean Surgeons by performing a survey of the members of the Korean Surgical Society. PMID:23646310

Mapping the rupture process of moderate earthquakes by inverting accelerograms

USGS Publications Warehouse

Hellweg, M.; Boatwright, J.

1999-01-01

We present a waveform inversion method that uses recordings of small events as Green's functions to map the rupture growth of moderate earthquakes. The method fits P and S waveforms from many stations simultaneously in an iterative procedure to estimate the subevent rupture time and amplitude relative to the Green's function event. We invert the accelerograms written by two moderate Parkfield earthquakes using smaller events as Green's functions. The first earthquake (M = 4.6) occurred on November 14, 1993, at a depth of 11 km under Middle Mountain, in the assumed preparation zone for the next Parkfield main shock. The second earthquake (M = 4.7) occurred on December 20, 1994, some 6 km to the southeast, at a depth of 9 km on a section of the San Andreas fault with no previous microseismicity and little inferred coseismic slip in the 1966 Parkfield earthquake. The inversion results are strikingly different for the two events. The average stress release in the 1993 event was 50 bars, distributed over a geometrically complex area of 0.9 km2. The average stress release in the 1994 event was only 6 bars, distributed over a roughly elliptical area of 20 km2. The ruptures of both events appear to grow spasmodically into relatively complex shapes: the inversion only constrains the ruptures to grow more slowly than the S wave velocity but does not use smoothness constraints. Copyright 1999 by the American Geophysical Union.

Heat stress and a countermeasure in the Shuttle rescueman's suit

NASA Technical Reports Server (NTRS)

Doerr, D. F.; Reed, H.; Convertino, V. A.

1992-01-01

Rescue of the astronaut flight crew from a contingency landing may risk exposure of the rescue crew to toxic propellants spilling from potentially ruptured tanks in the crew module area. An Aquala dry diver's suit has been in service by the rescue team to preclude exposure, especially in the water rescue scenario. Heat stress has become a factor of concern in recent years when older and less physically-fit team members work in this suit. Methods: Field testing was initiated using fully instrumented rescue men in a simulated scenario to determine the extent of heat stress. Two tests were accomplished, one in the normal (N) configuration and one with a proposed cooling countermeasure, the Steele vest (S). Results: Heat stress was high as indicated by average rectal temperatures (Tre) of 38.28 degrees C(100.9 degrees F) after the 45 minute protocol. Slopes of the regression equations describing the increase in Tre with time were greater (P less than 0.05) with N (0.073 plus or minus .008) compared to S (0.060 plus or minus .007). Projection of time to the 38.89 degree C (102 degree F) limit was increased by 15.3 percent with the vest. Mean skin temperature (Tsk) was higher (P less than 0.05) in N (38.33 plus or minus .11 degrees C) compared to S (34.33 plus or minus .39 degrees C). Average heart rate was higher (P less than 0.05 in N than S. Sweat loss, as measured by weight loss, was more (P less than 0.05) for N (1.09 plus or minus .09 kg versus 0.77 plus or minus .06 kg). Air usage, while slightly less for S, was not statistically different. Conclusion: The use of the cool vest provided significant relief from thermal stress in spite of the addition of 3.4 kg (7.5 pounds) weight and some loss in mobility.

ESTIMATION OF EFFECTIVE SHEAR STRESS WORKING ON FLAT SHEET MEMBRANE USING FLUIDIZED MEDIA IN MBRs

NASA Astrophysics Data System (ADS)

Zaw, Hlwan Moe; Li, Tairi; Nagaoka, Hiroshi; Mishima, Iori

This study was aimed at estimating effective shear stress working on flat sheet membrane by the addition of fluidized media in MBRs. In both of laboratory-scale aeration tanks with and without fluidized media, shear stress variations on membrane surface and water phase velocity variations were measured and MBR operation was conducted. For the evaluation of the effective shear stress working on membrane surface to mitigate membrane surface, simulation of trans-membrane pressure increase was conducted. It was shown that the time-averaged absolute value of shear stress was smaller in the reactor with fluidized media than without fluidized media. However, due to strong turbulence in the reactor with fluidized media caused by interaction between water-phase and media and also due to the direct interaction between membrane surface and fluidized media, standard deviation of shear stress on membrane surface was larger in the reactor with fluidized media than without media. Histograms of shear stress variation data were fitted well to normal distribution curves and mean plus three times of standard deviation was defined to be a maximum shear stress value. By applying the defined maximum shear stress to a membrane fouling model, trans-membrane pressure curve in the MBR experiment was simulated well by the fouling model indicting that the maximum shear stress, not time-averaged shear stress, can be regarded as an effective shear stress to prevent membrane fouling in submerged flat-sheet MBRs.

The turbulent mean-flow, Reynolds-stress, and heat flux equations in mass-averaged dependent variables

NASA Technical Reports Server (NTRS)

Rubesin, M. W.; Rose, W. C.

1973-01-01

The time-dependent, turbulent mean-flow, Reynolds stress, and heat flux equations in mass-averaged dependent variables are presented. These equations are given in conservative form for both generalized orthogonal and axisymmetric coordinates. For the case of small viscosity and thermal conductivity fluctuations, these equations are considerably simpler than the general Reynolds system of dependent variables for a compressible fluid and permit a more direct extension of low speed turbulence modeling to computer codes describing high speed turbulence fields.

Design optimization of a radial functionally graded dental implant.

PubMed

Ichim, Paul I; Hu, Xiaozhi; Bazen, Jennifer J; Yi, Wei

2016-01-01

In this work, we use FEA to test the hypothesis that a low-modulus coating of a cylindrical zirconia dental implant would reduce the stresses in the peri-implant bone and we use design optimization and the rule of mixture to estimate the elastic modulus and the porosity of the coating that provides optimal stress shielding. We show that a low-modulus coating of a dental implant significantly reduces the maximum stresses in the peri-implant bone without affecting the average stresses thus creating a potentially favorable biomechanical environment. Our results suggest that a resilient coating is capable of reducing the maximum compressive and tensile stresses in the peri-implant bone by up to 50% and the average stresses in the peri-implant bone by up to 15%. We further show that a transitional gradient between the high-modulus core and the low-modulus coating is not necessary and for a considered zirconia/HA composite the optimal thickness of the coating is 100 µ with its optimal elastic at the lowest value considered of 45 GPa. © 2015 Wiley Periodicals, Inc.

Dispersive aortic cannulas reduce aortic wall shear stress affecting atherosclerotic plaque embolization.

PubMed

Assmann, Alexander; Gül, Fethi; Benim, Ali Cemal; Joos, Franz; Akhyari, Payam; Lichtenberg, Artur

2015-03-01

Neurologic complications during on-pump cardiovascular surgery are often induced by mobilization of atherosclerotic plaques, which is directly related to enhanced wall shear stress. In the present study, we numerically evaluated the impact of dispersive aortic cannulas on aortic blood flow characteristics, with special regard to the resulting wall shear stress profiles. An idealized numerical model of the human aorta and its branches was created and used to model straight as well as bent dispersive aortic cannulas with meshlike tips inserted in the distal ascending aorta. Standard cannulas with straight beveled or bent tips served as controls. Using a recently optimized computing method, simulations of pulsatile and nonpulsatile extracorporeal circulation were performed. Dispersive aortic cannulas reduced the maximum and average aortic wall shear stress values to approximately 50% of those with control cannulas, while the difference in local values was even larger. Moreover, under pulsatile circulation, dispersive cannulas shortened the time period during which wall shear stress values were increased. The turbulent kinetic energy was also diminished by utilizing dispersive cannulas, reducing the risk of hemolysis. In summary, dispersive aortic cannulas decrease aortic wall shear stress and turbulence during extracorporeal circulation and may therefore reduce the risk of endothelial and blood cell damage as well as that of neurologic complications caused by atherosclerotic plaque mobilization. Copyright © 2014 International Center for Artificial Organs and Transplantation and Wiley Periodicals, Inc.

Psychological and Social Factors Affecting Internet Searches on Suicide in Korea: A Big Data Analysis of Google Search Trends

PubMed Central

Song, Tae Min; Song, Juyoung; Hayman, Laura L.; Woo, Jong-Min

2014-01-01

Purpose The average mortality rate for death by suicide among OECD countries is 12.8 per 100000, and 33.5 for Korea. The present study analyzed big data extracted from Google to identify factors related to searches on suicide in Korea. Materials and Methods Google search trends for the search words of suicide, stress, exercise, and drinking were obtained for 2004-2010. Analyzing data by month, the relationship between the actual number of suicides and search words per year was examined using multi-level models. Results Both suicide rates and Google searches on suicide in Korea increased since 2007. An unconditional slope model indicated stress and suicide-related searches were positively related. A conditional model showed that factors associated with suicide by year directly affected suicide-related searches. The interaction between stress-related searches and the actual number of suicides was significant. Conclusion A positive relationship between stress- and suicide-related searches further confirmed that stress affects suicide. Taken together and viewed in context of the big data analysis, our results point to the need for a tailored prevention program. Real-time big data can be of use in indicating increases in suicidality when search words such as stress and suicide generate greater numbers of hits on portals and social network sites. PMID:24339315

Stress free configuration of the human eye.

PubMed

Elsheikh, Ahmed; Whitford, Charles; Hamarashid, Rosti; Kassem, Wael; Joda, Akram; Büchler, Philippe

2013-02-01

Numerical simulations of eye globes often rely on topographies that have been measured in vivo using devices such as the Pentacam or OCT. The topographies, which represent the form of the already stressed eye under the existing intraocular pressure, introduce approximations in the analysis. The accuracy of the simulations could be improved if either the stress state of the eye under the effect of intraocular pressure is determined, or the stress-free form of the eye estimated prior to conducting the analysis. This study reviews earlier attempts to address this problem and assesses the performance of an iterative technique proposed by Pandolfi and Holzapfel [1], which is both simple to implement and promises high accuracy in estimating the eye's stress-free form. A parametric study has been conducted and demonstrated reliance of the error level on the level of flexibility of the eye model, especially in the cornea region. However, in all cases considered 3-4 analysis iterations were sufficient to produce a stress-free form with average errors in node location <10(-6)mm and a maximal error <10(-4)mm. This error level, which is similar to what has been achieved with other methods and orders of magnitude lower than the accuracy of current clinical topography systems, justifies the use of the technique as a pre-processing step in ocular numerical simulations. Crown Copyright © 2012. Published by Elsevier Ltd. All rights reserved.

[Stress among nurses: an examination of salivary cortisol levels on work and day off].

PubMed

Pires da Rocha, Maria Cecília; Figueiredo de Martino, Milva Maria; Grassi-Kassisse, Dora Maria; Luiz de Souza, Aglécio

2013-10-01

The present study evaluates the use of salivary cortisol concentration as a physiological index of the stress level among nurses on their work day and day off and correlates it with the questionnaire used to measure occupational stress in nurses (Inventário de Estresse em Enfermeiros - IEE). This is a comparative, cross-sectional descriptive study in which sociodemographic data, IEE results and salivary cortisol levels were used. Fifty-seven nurses participated in the study (80.7% females and a mean age of 37.1 years old). The IEE average score was 124.5. The average cortisol level was 564.1 ng/m on work day and 354.1 ng/mL on day off. Nurses who had double workdays presented high values of salivary cortisol during the work day (638.1 ng/mL). In conclusion, salivary cortisol identified the nurses' stress level, and differences were found between a work day and day off. On the nurses' day off, their salivary cortisol levels and stress scores were lower.

Medial malleolar stress fracture secondary to chronic ankle impingement.

PubMed

Jowett, Andrew J L; Birks, Christopher L; Blackney, Mark C

2008-07-01

Medial malleolar stress fractures are uncommon even in the sporting population. We believe that stress fractures of the medial malleolus may be the end stage of chronic anteromedial ankle impingement in elite running and jumping athletes. We present five cases of elite athletes who presented to our institution with stress fractures of the medial malleolus over a 3-year period (2004 to 2007). In each case preoperative imaging revealed an anteromedial bony spur on the tibia. All fractures were internally fixed and at the same sitting had arthroscopic debridement of the bony spur. All fractures united without further intervention, average time to union was 10.2 (range, 6 to 16) weeks. At most recent review (average, 18 months; range, 8 to 37 months), all patients had resumed sporting activity to their previous level. No patient had suffered a recurrent fracture of the medial malleolus. We believe this region of impingement to be important in the development of the stress fracture and should be addressed at the time of fracture fixation.

Characterizing cycle-to-cycle variations of the shedding cycle in the turbulent wake of a normal flat plate using generalized phase averages

NASA Astrophysics Data System (ADS)

Martinuzzi, Robert

2016-11-01

Quasi-periodic vortex shedding in the turbulent wake of a thin-flat plate placed normal to a uniform stream at Reynolds number of 6700 is investigated based on Particle Image Velocimetry experiments. The wake structure and vortex formation are characterized using a generalized phase average (GPA), a refinement of the triple decomposition of Reynolds and Hussain (1970) incorporating elements of mean-field theory (Stuart, 1958). The resulting analysis highlights the importance of cycle-to-cycle variations in characterizing vortex formation, wake topology and the residual turbulent Reynolds Stresses. For example, it is shown that during high-amplitude cycles vorticity is strongly concentrated within the well-organized shed vortices, whereas during low-amplitude cycles the shed vortices are highly distorted resulting in significant modulation of the shedding frequency. It is found that high-amplitude cycles contribute more to the coherent Reynolds stress field while the low-amplitude cycles contribute to the residual stress field. It is further shown that traditional phase-averaging techniques lead to an over-estimation of the residual stress field. Natural Sciences and Engineering Research Council of Canada.

Sexual Self-concept and Its Relationship to Depression, Stress and Anxiety in Postmenopausal Women.

PubMed

Heidari, Mohammad; Ghodusi, Mansureh; Rafiei, Hossein

2017-04-01

Women in menopause have the more mood swings than before menopause. At the same time seem to sexual self-concept and sexual aspects of self-knowledge has a great impact on their mental health. This study aimed to investigate the sexual self-concept and its relationship to depression, stress and anxiety in postmenopausal women's. In this descriptive correlation research, 300 of postmenopausal women referred to healthcare and medical treatment centers in Abadeh city were selected by convenience sampling method. The information in this study was collected by using questionnaires of multidimensional sexual self-concept and depression anxiety stress scale 21 (DASS-21). For data analysis, SPSS/17 software was used. The results showed the mean score positive sexual self-concept was 41.03 ± 8.66 and the average score of negative sexual self in women's was 110.32 ± 43.05. As well as scores of depression, stress, and anxiety, 35.67%, 32.33% and 37.67% respectively were in severe level. Positive and negative sexual self-concept scores with scores of stress, anxiety, and depression, of post-menopausal women in the confidence of 0.01, is significantly correlated ( P < 0.05). Being stress, anxiety, and depression in severe level and also a significant correlation between increased stress, anxiety and depression with negative and weak self-concept of women's, it is necessary to devote more careful attention to mental health issues of women's and have appropriate interventions.

Stress engineering of high-quality single crystal diamond by heteroepitaxial lateral overgrowth

DOE PAGES

Tang, Y. -H.; Golding, B.

2016-02-02

Here, we describe a method for lateral overgrowth of low-stress single crystal diamond by chemical vapor deposition (CVD). The process is initiated by deposition of a thin (550 nm) (001) diamond layer on Ir-buffered a-plane sapphire. The diamond is partially masked by periodic thermally evaporated Au stripes using photolithography. Lateral overgrowth of the Au occurs with extremely effective filtering of threading dislocations. Thermal stress resulting from mismatch of the low thermal expansion diamond and the sapphire substrate is largely accommodated by the ductile Au layer. The stress state of the diamond is investigated by Raman spectroscopy for two thicknesses: atmore » 10 μm where the film has just overgrown the Au mask and at 180 μm where the film thickness greatly exceeds the scale of the masking. For the 10-μm film, the Raman linewidth shows spatial oscillations with the period of the Au stripes with a factor of 2 to 3 reduction relative to the unmasked region. In a 180-μm thick diamond film, the overall surface stress was extremely low, 0.00 ± 0.16 GPa, obtained from the Raman shift averaged over the 7.5mm diameter of the crystal at its surface. We conclude that the metal mask protects the overgrown diamond layer from substrate-induced thermal stress and cracking. Lastly, it is also responsible for low internal stress by reducing dislocation density by several orders of magnitude.« less

A cross-sectional study of the association between mobile phone use and symptoms of ill health.

PubMed

Cho, Yong Min; Lim, Hee Jin; Jang, Hoon; Kim, Kyunghee; Choi, Jae Wook; Shin, Chol; Lee, Seung Ku; Kwon, Jong Hwa; Kim, Nam

2016-01-01

This study analyzed the associations between mobile phone call frequency and duration with non-specific symptoms. This study was conducted with a population group including 532 non-patient adults established by the Korean Genome and Epidemiology Study. The pattern of phone call using a mobile phone was investigated through face-to-face interview. Structured methods applied to quantitatively assess health effects are Headache Impact Test-6 (HIT-6), Psychosocial Well-being Index-Short Form, Beck Depression Inventory, Korean-Instrumental Activities of Daily Living, Perceived Stress Scale (PSS), Pittsburgh Sleep Quality Index, and 12-item Short Form Health Survey where a higher score represents a higher greater health effect. The average daily phone call frequency showed a significant correlation with the PSS score in female subjects. Increases in the average duration of one phone call were significantly correlated with increases in the severity of headaches in both sexes. The mean (standard deviation) HIT-6 score in the subgroup of subjects whose average duration of one phone call was five minutes or longer was 45.98 (8.15), as compared with 42.48 (7.20) in those whose average duration of one phone call was <5 minutes. The severity of headaches was divided into three levels according to the HIT-6 score (little or no impact/moderate impact/substantial or severe impact), and a logistic regression analysis was performed to investigate the association between an increased phone call duration and the headache severity. When the average duration of one phone call was five minutes or longer, the odds ratio (ORs) and the 95% confidence intervals (CIs) for the moderate impact group were 2.22 and 1.18 to 4.19, respectively. The OR and 95% CI for the substantial or severe impact group were 4.44 and 2.11 to 8.90, respectively. Mobile phone call duration was not significantly associated with stress, sleep, cognitive function, or depression, but was associated with the severity of headaches.

Another Look at Strong Ground Motion Accelerations and Stress Drop

NASA Astrophysics Data System (ADS)

Baltay, A.; Prieto, G.; Ide, S.; Hanks, T. C.; Beroza, G. C.

2010-12-01

The relationship between earthquake stress drop and ground motion acceleration is central to seismic hazard analysis. We revisit measurements of root-mean-square (RMS) acceleration, arms, using KikNet accelerometer data from Japan. We directly measure RMS and peak acceleration, and estimate both apparent stress and corner frequencies using the empirical Green’s function (eGf) coda method of Baltay et al. [2010]. We predict armsfrom corner frequency and stress drop following McGuire and Hanks [1980] to compare with measurements. The theoretical relationship does a good job of predicting observed arms. We use four earthquake sequences in Japan to investigate the source parameters and accelerations: the 2008 Iwate-Miyagi earthquake; the off-Kamaishi repeating sequence; and the 2004 and 2007 Niigata events. In each data set, we choose events that are nearly co-located so that the path term to any station is constant. Small events are used as empirical Green’s functions to correct for propagation effects. For all sequences, we find that the apparent stress averages ~1 MPa for most events. Corner frequencies are consistent with Mo-1/3 scaling. We find the ratio of stress drop and apparent stress to be 5, consistent with the theoretical derivation of Singh and Ordaz [1994], using a Brune [1970] spectra. armsis theoretically proportional to stress drop and the inverse square root of the corner frequency. We show that this calculation can be used as a proxy for armsobservations from strong motion records, using recent data from the four earthquake sequences mentioned above. Even for the Iwate-Miyagi mainshock, which experienced over 4 g’s of acceleration, we find that apparent stress, stress drop and corner frequency follow expected scaling laws and support self-similarity.

Differences in stress-related ratings between research center and home environments in dementia caregivers using ecological momentary assessment.

PubMed

Fonareva, Irina; Amen, Alexandra M; Ellingson, Roger M; Oken, Barry S

2012-01-01

Clinicians and researchers working with dementia caregivers typically assess caregiver stress in a clinic or research center, but caregivers' stress is rooted at home where they provide care. This study aimed to compare ratings of stress-related measures obtained in research settings and in the home using ecological momentary assessment (EMA). EMA of 18 caregivers (mean age 66.4 years ±7.8; 89% females) and 23 non-caregivers (mean age 66.4 years ±7.9; 87% females) was implemented using a personal digital assistant. Subjects rated their perceived stress, fatigue, coping with current situation, mindfulness, and situational demand once in the research center and again at 3-4 semi-random points during a day at home. The data from several assessments conducted at home were averaged for statistical analyses and compared with the data collected in the research center. The testing environment had a differential effect on caregivers and non-caregivers for the ratings of perceived stress (p < 0.01) and situational demand (p = 0.01). When tested in the research center, ratings for all measures were similar between groups, but when tested at home, caregivers rated their perceived stress as higher than non-caregivers (p = 0.02). Overall, caregivers reported higher perceived stress at home than in the research center (p = 0.02), and non-caregivers reported greater situational demand in the research center than at home (p < 0.01). The assessment method and environment affect stress-related outcomes. Evaluating participants in their natural environment provides a more sensitive measure of stress-related outcomes. EMA provides a convenient way to gather data when evaluating dementia caregivers.

[Study of the occupational stress norm and it's application for the executive group and administrative support group].

PubMed

Yang, Xin-wei; Wang, Zhi-ming; Jin, Tai-yi; Lan, Ya-jia

2006-07-01

A study of the occupational stress norm and it's application for the executive group and administrative support group. In this study, cross-sectional study method is used, and a synthetic way of sorting and randomized sampling is adopted to deal with research targets (263 executive group, 569 administrative support group). Descriptive statistics for OSI-R scale scores for the executive group, administrative support group were modulated. Scale raw score to T-score conversion tables derived from the OSI-R normative sample for executive group, administrative support group were established. OSI-R profile from for executive group, administrative support group were established. For the ORQ and PSQ scales, scores at or above 70 indicate a strong levels of maladaptive stress and strain. Score inthe range of 60 to 69 suggest middle levels of maladaptive stress and strain. Score in the range of 40 to 59 indicate normal levels of stress and strain. Score below 40 indicate a relative absence of occupational stress and strain. For the PRQ scales, score below 30 indicate a significant lack of coping resources. Score in the range of 30 to 39 suggest middle deficits in coping resources. Score in the range of 40 to 59 indicate average coping resources. Scores at or above 60 indicate a strong levels of coping resources. Based on occupational Stress norm, raw score to T-score conversion tables, OSI-R profile form and classification criterion, we could estimate the level of occupation stress, stressor, strain and coping resources in different occupation. In addition, we combined subjective and objective environment match model of occupational stress. The various individual and organizational intervention measures should be taken to reduce the occupational stress and to increase coping so as to improve the work ability.

Impact of stressful life events on central adiposity in the Pelotas Birth Cohort

PubMed Central

Surkan, Pamela J; Sakyi, Kwame S; Hu, Alice; Olinto, Maria T; Gonçalves, Helen; Horta, Bernardo L; Gigante, Denise P

2018-01-01

ABSTRACT OBJECTIVE: To investigate how stressful life events and social support relate to central adiposity in Southern Brazil. METHODS: Data included information from 802 participants in the 1982 Pelotas Birth Cohort that was collect in 2004-2005 and 2006. Stratifying by sex, we studied self-reported stressful life events during the year before 2004-2005 in relation to change in waist circumference between 2004-2005 and 2006 and waist-to-hip ratio in 2006, using both bivariate and multivariate linear regression models. RESULTS: In adjusted models, the experience of stressful life events during the year before 2004-2005 predicted a change in waist circumference in 2006 in men and a change in both waist-to-hip ratio in 2006 and waist circumference between 2004-2005 and 2006 in women. Men who experienced two or more stressful events had on average a one centimeter increase in their waist circumference between 2004-2005 and 2006 (β = 0.97, 95%CI 0.02-1.92), compared to those reporting no stressful events. For women, those who had one and those who had two or more stressful life events had over a 1 cm increase in their waist circumference from 2004-2005 to 2006 (β = 1.37, 95%CI 0.17-2.54; β = 1.26, 95%CI 0.11-2.40, respectively), compared to those who did not experience any stressful event. For both sexes, social support level was not significantly related to either waist-to-hip ratio or change in waist circumference, and it did not modify the association between stress and central adiposity. CONCLUSIONS: The experience of more than one stressful life event was associated with distinct indicators of central adiposity for men versus women. PMID:29791680

Emotional stress recognition using a new fusion link between electroencephalogram and peripheral signals

PubMed Central

Hosseini, Seyyed Abed; Khalilzadeh, Mohammad Ali; Naghibi-Sistani, Mohammad Bagher; Homam, Seyyed Mehran

2015-01-01

Background: This paper proposes a new emotional stress assessment system using multi-modal bio-signals. Electroencephalogram (EEG) is the reflection of brain activity and is widely used in clinical diagnosis and biomedical research. Methods: We design an efficient acquisition protocol to acquire the EEG signals in five channels (FP1, FP2, T3, T4 and Pz) and peripheral signals such as blood volume pulse, skin conductance (SC) and respiration, under images induction (calm-neutral and negatively excited) for the participants. The visual stimuli images are selected from the subset International Affective Picture System database. The qualitative and quantitative evaluation of peripheral signals are used to select suitable segments of EEG signals for improving the accuracy of signal labeling according to emotional stress states. After pre-processing, wavelet coefficients, fractal dimension, and Lempel-Ziv complexity are used to extract the features of the EEG signals. The vast number of features leads to the problem of dimensionality, which is solved using the genetic algorithm as a feature selection method. Results: The results show that the average classification accuracy is 89.6% for two categories of emotional stress states using the support vector machine (SVM). Conclusion: This is a great improvement in results compared to other similar researches. We achieve a noticeable improvement of 11.3% in accuracy using SVM classifier, in compared to previous studies. Therefore, a new fusion between EEG and peripheral signals are more robust in comparison to the separate signals. PMID:26622979

An Efficient Implementation of the GMC Micromechanics Model for Multi-Phased Materials with Complex Microstructures

NASA Technical Reports Server (NTRS)

Pindera, Marek-Jerzy; Bednarcyk, Brett A.

1997-01-01

An efficient implementation of the generalized method of cells micromechanics model is presented that allows analysis of periodic unidirectional composites characterized by repeating unit cells containing thousands of subcells. The original formulation, given in terms of Hill's strain concentration matrices that relate average subcell strains to the macroscopic strains, is reformulated in terms of the interfacial subcell tractions as the basic unknowns. This is accomplished by expressing the displacement continuity equations in terms of the stresses and then imposing the traction continuity conditions directly. The result is a mixed formulation wherein the unknown interfacial subcell traction components are related to the macroscopic strain components. Because the stress field throughout the repeating unit cell is piece-wise uniform, the imposition of traction continuity conditions directly in the displacement continuity equations, expressed in terms of stresses, substantially reduces the number of unknown subcell traction (and stress) components, and thus the size of the system of equations that must be solved. Further reduction in the size of the system of continuity equations is obtained by separating the normal and shear traction equations in those instances where the individual subcells are, at most, orthotropic. The reformulated version facilitates detailed analysis of the impact of the fiber cross-section geometry and arrangement on the response of multi-phased unidirectional composites with and without evolving damage. Comparison of execution times obtained with the original and reformulated versions of the generalized method of cells demonstrates the new version's efficiency.

Form drag in rivers due to small-scale natural topographic features: 1. Regular sequences

USGS Publications Warehouse

Kean, J.W.; Smith, J.D.

2006-01-01

Small-scale topographic features are commonly found on the boundaries of natural rivers, streams, and floodplains. A simple method for determining the form drag on these features is presented, and the results of this model are compared to laboratory measurements. The roughness elements are modeled as Gaussian-shaped features defined in terms of three parameters: a protrusion height, H; a streamwise length scale, ??; and a spacing between crests, ??. This shape is shown to be a good approximation to a wide variety of natural topographic bank features. The form drag on an individual roughness element embedded in a series of identical elements is determined using the drag coefficient of the individual element and a reference velocity that includes the effects of roughness elements further upstream. In addition to calculating the drag on each element, the model determines the spatially averaged total stress, skin friction stress, and roughness height of the boundary. The effects of bank roughness on patterns of velocity and boundary shear stress are determined by combining the form drag model with a channel flow model. The combined model shows that drag on small-scale topographic features substantially alters the near-bank flow field. These methods can be used to improve predictions of flow resistance in rivers and to form the basis for fully predictive (no empirically adjusted parameters) channel flow models. They also provide a foundation for calculating the near-bank boundary shear stress fields necessary for determining rates of sediment transport and lateral erosion.

Relationship between stress coping and sleep disorders among the general Japanese population: a nationwide representative survey.

PubMed

Otsuka, Yuichiro; Kaneita, Yoshitaka; Itani, Osamu; Nakagome, Sachi; Jike, Maki; Ohida, Takashi

2017-09-01

To clarify the prevalence of stress, and examine the relationship between sleep disorders and stress coping strategies among highly stressed individuals in the general Japanese population. A cross-sectional nationwide survey was undertaken in November 2007. Men and women were randomly selected from 300 districts throughout Japan. Data from 7671 (3532 men (average age 53.5 ± 17.0 years) and 4139 women (average age 53.9 ± 17.7 years)) were analyzed. Participants completed a self-reported questionnaire on stress, sleep disorders, and stress coping strategies in the previous month. Highly stressed individuals comprised 16.6% (95% confidence interval 15.8-17.5%) of the total sample, and most were aged 20-49 years. In multiple logistic regression, symptoms of insomnia (ie, difficulty initiating sleep, difficulty maintaining sleep, and early morning awakening), excessive daytime sleepiness, nightmares, daytime malfunction, and lack of rest due to sleep deprivation were more prone to occur in highly stressed individuals. In addition, logistic regression analysis controlling for other adjustment factors revealed that stress coping strategies such as 'giving up on problem-solving', 'enduring problems patiently', 'smoking' and 'drinking alcohol' were positively associated with the above-mentioned sleep disorders. On the other hand, stress coping strategies such as 'exercising', 'enjoying hobbies', and 'sharing worries' were inversely associated with the above-mentioned sleep disorders. Distraction-based stress coping (eg, hobbies, exercise, and optimistic thinking) was found to be preferable to problem-based stress coping in a highly stressed Japanese general population. Copyright © 2017 Elsevier B.V. All rights reserved.

Associations between air pollution and perceived stress: the Veterans Administration Normative Aging Study.

PubMed

Mehta, Amar J; Kubzansky, Laura D; Coull, Brent A; Kloog, Itai; Koutrakis, Petros; Sparrow, David; Spiro, Avron; Vokonas, Pantel; Schwartz, Joel

2015-01-27

There is mixed evidence suggesting that air pollution may be associated with increased risk of developing psychiatric disorders. We aimed to investigate the association between air pollution and non-specific perceived stress, often a precursor to development of affective psychiatric disorders. This longitudinal analysis consisted of 987 older men participating in at least one visit for the Veterans Administration Normative Aging Study between 1995 and 2007 (n = 2,244 visits). At each visit, participants were administered the 14-item Perceived Stress Scale (PSS), which quantifies stress experienced in the previous week. Scores ranged from 0-56 with higher scores indicating increased stress. Differences in PSS score per interquartile range increase in moving average (1, 2, and 4-weeks) of air pollution exposures were estimated using linear mixed-effects regression after adjustment for age, race, education, physical activity, anti-depressant medication use, seasonality, meteorology, and day of week. We also evaluated effect modification by season (April-September and March-October for warm and cold season, respectively). Fine particles (PM2.5), black carbon (BC), nitrogen dioxide, and particle number counts (PNC) at moving averages of 1, 2, and 4-weeks were associated with higher perceived stress ratings. The strongest associations were observed for PNC; for example, a 15,997 counts/cm(3) interquartile range increase in 1-week average PNC was associated with a 3.2 point (95%CI: 2.1-4.3) increase in PSS score. Season modified the associations for specific pollutants; higher PSS scores in association with PM2.5, BC, and sulfate were observed mainly in colder months. Air pollution was associated with higher levels of perceived stress in this sample of older men, particularly in colder months for specific pollutants.

Effect of needle insertion speed on tissue injury, stress, and backflow distribution for convection-enhanced delivery in the rat brain.

PubMed

Casanova, Fernando; Carney, Paul R; Sarntinoranont, Malisa

2014-01-01

Flow back along a needle track (backflow) can be a problem during direct infusion, e.g. convection-enhanced delivery (CED), of drugs into soft tissues such as brain. In this study, the effect of needle insertion speed on local tissue injury and backflow was evaluated in vivo in the rat brain. Needles were introduced at three insertion speeds (0.2, 2, and 10 mm/s) followed by CED of Evans blue albumin (EBA) tracer. Holes left in tissue slices were used to reconstruct penetration damage. These measurements were also input into a hyperelastic model to estimate radial stress at the needle-tissue interface (pre-stress) before infusion. Fast insertion speeds were found to produce more tissue bleeding and disruption; average hole area at 10 mm/s was 1.87-fold the area at 0.2 mm/s. Hole measurements also differed at two fixation time points after needle retraction, 10 and 25 min, indicating that pre-stresses are influenced by time-dependent tissue swelling. Calculated pre-stresses were compressive (0 to 485 Pa) and varied along the length of the needle with smaller average values within white matter (116 Pa) than gray matter (301 Pa) regions. Average pre-stress at 0.2 mm/s (351.7 Pa) was calculated to be 1.46-fold the value at 10 mm/s. For CED backflow experiments (0.5, 1, and 2 µL/min), measured EBA backflow increased as much as 2.46-fold between 10 and 0.2 mm/s insertion speeds. Thus, insertion rate-dependent damage and changes in pre-stress were found to directly contribute to the extent of backflow, with slower insertion resulting in less damage and improved targeting.

Role of pseudo-turbulent stresses in shocked particle clouds and construction of surrogate models for closure

NASA Astrophysics Data System (ADS)

Sen, O.; Gaul, N. J.; Davis, S.; Choi, K. K.; Jacobs, G.; Udaykumar, H. S.

2018-05-01

Macroscale models of shock-particle interactions require closure terms for unresolved solid-fluid momentum and energy transfer. These comprise the effects of mean as well as fluctuating fluid-phase velocity fields in the particle cloud. Mean drag and Reynolds stress equivalent terms (also known as pseudo-turbulent terms) appear in the macroscale equations. Closure laws for the pseudo-turbulent terms are constructed in this work from ensembles of high-fidelity mesoscale simulations. The computations are performed over a wide range of Mach numbers ( M) and particle volume fractions (φ ) and are used to explicitly compute the pseudo-turbulent stresses from the Favre average of the velocity fluctuations in the flow field. The computed stresses are then used as inputs to a Modified Bayesian Kriging method to generate surrogate models. The surrogates can be used as closure models for the pseudo-turbulent terms in macroscale computations of shock-particle interactions. It is found that the kinetic energy associated with the velocity fluctuations is comparable to that of the mean flow—especially for increasing M and φ . This work is a first attempt to quantify and evaluate the effect of velocity fluctuations for problems of shock-particle interactions.

Abdominal Aortic Hemodynamics in Intermittent Claudication Patients at Rest and During Dynamic Pedaling Exercise

PubMed Central

Cheng, Christopher P.; Taylor, Charles A.; Dalman, Ronald L.

2015-01-01

Introduction Lower extremity exercise has been shown to eliminate adverse hemodynamics conditions, such as low and oscillating blood flow and wall shear stress, in the abdominal aortas of healthy young and older adults. Methods We use cine phase-contrast magnetic resonance imaging and a custom MRI-compatible exercise cycle to quantify hemodynamic changes due to pedaling exercise in patients diagnosed with intermittent claudication. Results and Conclusions With only an average heart increase of 35±18% and exercise workload of 36±16 Watts, the patients experienced approximately 3- and 6-fold increases in blood flow, and 4- and 16-fold increases in wall shear stress at the supraceliac and infrarenal aortic locations, respectively. Also, all oscillations in flow and shear stress at rest were eliminated with exercise. Claudication patients experience 3 to 4-fold lower oscillations in flow and shear stress at rest as compared to healthy age-matched controls, likely due to reduced distal arterial compliance as a result of distal atherosclerosis. The magnitude of flow and shear oscillatory indices may be good indicators of distal arterial compliance and health, and may provide predictive power for the efficacy of focal interventions. PMID:26315797

Analysis of wall shear stress around a competitive swimmer using 3D Navier-Stokes equations in CFD.

PubMed

Popa, C V; Zaidi, H; Arfaoui, A; Polidori, G; Taiar, R; Fohanno, S

2011-01-01

This paper deals with the flow dynamics around a competitive swimmer during underwater glide phases occurring at the start and at every turn. The influence of the head position, namely lifted up, aligned and lowered, on the wall shear stress and the static pressure distributions is analyzed. The problem is considered as 3D and in steady hydrodynamic state. Three velocities (1.4 m/s, 2.2 m/s and 3.1 m/s) that correspond to inter-regional, national and international swimming levels are studied. The flow around the swimmer is assumed turbulent. The Reynolds-averaged Navier-Stokes (RANS) equations are solved with the standard k-ω turbulent model by using the CFD (computational fluid dynamics) numerical method based on a volume control approach. Numerical simulations are carried out with the ANSYS FLUENT® CFD code. The results show that the wall shear stress increases with the velocity and consequently the drag force opposing the movement of the swimmer increases as well. Also, high wall shear stresses are observed in the areas where the body shape, globally rigid in form, presents complex surface geometries such as the head, shoulders, buttocks, heel and chest.

Matrix regeneration agents improve wound healing in non-stressed human corneal epithelial cells.

PubMed

Robciuc, A; Arvola, R P J; Jauhiainen, M; Holopainen, J M

2018-04-01

PurposeMatrix regenerating agents (RGTAs) emerged as promising in vivo wound-healing agents. These agents could prove beneficial for the treatment of dry eye disease-associated corneal micro-erosions; therefore, we aimed to evaluate the wound healing efficacy of regenerative agents (RGTAs or serum) in an in vitro model of hyperosmolarity (HO) stressed and non-stressed human corneal epithelial cells.Patients and methodsThe migration and proliferation induced by the regenerative agents was evaluated using an in vitro scratch wound assay and brome-deoxy-uridine incorporation. The inflammatory profile and effects of osmoregulators were also investigated. The two-tailed paired t-test calculated the statistical significance, with P-value<0.05 considered significant.ResultsThe most efficient inducer of re-epithelization was 2% serum, followed closely by 2% RGTA with an average improvement in cell migration of 1.8- and 1.4-fold, respectively, when compared with the non-treated control. Hyperosmolar stress significantly reduced the restorative effects of both serum and RGTAs; these effects were, however, neutralized by the osmoregulator betaine.ConclusionThese findings suggest that RGTAs could provide efficient treatment for dry-eye associated corneal micro-lesions if ocular surface HO is neutralized.

Qigong in Injured Military Service Members.

PubMed

Reb, Anne Marie; Saum, Nancy Seaby; Murphy, Deborah Ann; Breckenridge-Sproat, Sara Todd; Su, Xiaogang; Bormann, Jill Ellen

2017-03-01

Wounded, ill, and injured (WII) Military Service members experience significant stress and are at risk for developing chronic conditions including posttraumatic stress disorder and depression. Qigong, a meditative movement practice, may positively affect their ability to engage in successful rehabilitation. We assessed the feasibility of Qigong practice in WII Service members returning from combat; effects on stress, sleep, and somatic symptoms; satisfaction; and participants' experience with the practice. Single-group, pre- and posttest, mixed methods approach. Twenty-six WII were enrolled. The program was designed to include 20 classes over 10 weeks. Participants completed self-report questionnaires, practice logs, and an exit interview. Average attendance was 8.14 classes ( SD = 4.9); mean engagement was 5.7 ( SD = 3.5) weeks. Participants endorsed a high level of satisfaction with the practice. Qualitative themes included coping with stress; feeling more resilient and empowered; improvement in symptoms including sleep and physical function; and factors affecting practice. Participant-reported facilitators included accessibility and portability of the practice; barriers included scheduling conflicts and personal challenges. Participants recommended offering shorter programs with flexible scheduling options, increasing program awareness, and including significant others in future classes. Qigong was safe, portable, and easily adapted for WII Service members.

Role of pseudo-turbulent stresses in shocked particle clouds and construction of surrogate models for closure

NASA Astrophysics Data System (ADS)

Sen, O.; Gaul, N. J.; Davis, S.; Choi, K. K.; Jacobs, G.; Udaykumar, H. S.

2018-02-01

Macroscale models of shock-particle interactions require closure terms for unresolved solid-fluid momentum and energy transfer. These comprise the effects of mean as well as fluctuating fluid-phase velocity fields in the particle cloud. Mean drag and Reynolds stress equivalent terms (also known as pseudo-turbulent terms) appear in the macroscale equations. Closure laws for the pseudo-turbulent terms are constructed in this work from ensembles of high-fidelity mesoscale simulations. The computations are performed over a wide range of Mach numbers (M) and particle volume fractions (φ ) and are used to explicitly compute the pseudo-turbulent stresses from the Favre average of the velocity fluctuations in the flow field. The computed stresses are then used as inputs to a Modified Bayesian Kriging method to generate surrogate models. The surrogates can be used as closure models for the pseudo-turbulent terms in macroscale computations of shock-particle interactions. It is found that the kinetic energy associated with the velocity fluctuations is comparable to that of the mean flow—especially for increasing M and φ . This work is a first attempt to quantify and evaluate the effect of velocity fluctuations for problems of shock-particle interactions.

Developing a program to promote stress resilience and self-care in first-year medical students.

PubMed

Thomas, Suzanne E; Haney, Myra K; Pelic, Chris M; Shaw, Darlene; Wong, Jeffrey G

2011-01-01

BACKGROUND: Facilitating stress resilience in future physicians is an important role of medical educators and administrators. We developed an extracurricular program and pilot tested the program on first year medical students. METHODS: Presentations on topics related to mental health, help-seeking, and stress resilience were presented (one topic per session). Attendance was voluntary. Attendees were requested to complete anonymous evaluations following each presentation. Primary outcome variables were rates of agreement that the presentation (1) was interesting, (2) provided valuable information, and (3) provided information relevant for the student's future practice as a physician. RESULTS: Each of the seven topics was attended on average by approximately half of the student body. Evaluations were very positive that presentations were interesting and provided information useful to maintaining balance during medical school (all had ≥85% rates of agreement). Evaluations by students were variable (41%-88% rates of agreement) on whether each presented information relevant for future practice. CONCLUSIONS: The results support that first-year medical students value explicit guidance on ways to bolster stress resilience and self-care during medical school. It is important to clarify with each presentation how the information is relevant to their future practice as a physician.

Links between alcohol and other drug problems and maltreatment among adolescent girls: Perceived discrimination, ethnic identity, and ethnic orientation as moderators

PubMed Central

Gray, Calonie M. K.; Montgomery, Marilyn J.

2012-01-01

Objectives This study examined the links between maltreatment, posttraumatic stress symptoms, ethnicity-specific factors (i.e., perceived discrimination, ethnic identity, and ethnic orientation), and alcohol and/or other drug (AOD) problems among adolescent girls. Methods These relations were examined using archived data from a community sample of 168 Black and Hispanic adolescent girls who participated in a school-based substance use intervention. Results The results revealed that maltreatment was linked to AOD problems, but only through its relation with posttraumatic stress symptoms; maltreatment was positively related to posttraumatic stress symptoms, which were positively related to AOD problems. Both perceived discrimination and ethnic orientation were significant moderators. Specifically, greater perceived discrimination was associated with an increased effect of maltreatment on posttraumatic stress symptoms. Ethnic orientation demonstrated protective properties in the relation between maltreatment and AOD problem severity, such that the effect of maltreatment on AOD problem severity was less for girls with average to high ethnic orientation compared to girls with low ethnic orientation. Conclusions The findings of this study underscore the importance of developing interventions for Black and Hispanic girls that target maltreatment and AOD use concurrently and address ethnicity-specific factors. PMID:22608406

The Influence of Relative Submergence on the Near-bed Flow Field: Implications for Bed-load Transport

NASA Astrophysics Data System (ADS)

Cooper, J.; Tait, S.; Marion, A.

2005-12-01

Bed-load is governed by interdependent mechanisms, the most significant being the interaction between bed roughness, surface layer composition and near-bed flow. Despite this, practically all transport rate equations are described as a function of average bed shear stress. Some workers have examined the role of turbulence in sediment transport (Nelson et al. 1995) but have not explored the potential significance of spatial variations in the near-bed flow field. This is unfortunate considering evidence showing that transport is spatially heterogeneous and could be linked to the spatial nature of the near-bed flow (Drake et al., 1988). An understanding is needed of both the temporal and spatial variability in the near-bed flow field. This paper presents detailed spatial velocity measurements of the near-bed flow field over a gravel-bed, obtained using Particle Image Velocimetry. These data have been collected in a laboratory flume under two regimes: (i) tests with one bed slope and different flow depths; and (ii) tests with a combination of flow depths and slopes at the same average bed shear stress. Results indicate spatial variation in the streamwise velocities of up to 45 per cent from the double-averaged velocity (averaged in both time and space). Under both regimes, as the depth increased, spatial variability in the flow field increased. The probability distributions of near-bed streamwise velocities became progressively more skewed towards the higher velocities. This change was more noticeable under regime (i). This has been combined with data from earlier tests in which the near-bed velocity close to an entraining grain was measured using a PIV/image analysis system (Chegini et al, 2002). This along with data on the shape of the probability density function of velocities capable of entraining individual grains derived from a discrete-particle model (Heald et al., 2004) has been used to estimate the distribution of local velocities required for grain motion in the above tests. The overlap between this distribution and the measured velocities are used to estimate entrainment rates. Predicted entrainment rates increase with relative submergence, even for similar bed shear stress. Assuming bed-load rate is the product of entrainment rate and hop length, and that hop lengths are sensibly stable, suggests that transport rate has a dependence on relative submergence. This demonstrates that transport rate is not a direct function of average bed shear stress. The results describe a mechanism that will cause river channels with contrasting morphologies (and different relative submergence) but similar levels of average bed stress to experience different levels of sediment mobility. Chegini A. Tait S. Heald J. McEwan I. 2002 The development of an automated system for the measurement of near bed turbulence and grain motion. Proc. ASCE Conf. on Hydraulic Measurements and Experimental Methods, ISBN 0-7844-0655-3. Drake T.G. Shreve R.L. Dietrich W.E. Whiting P.J. Leopold L.B. 1988 Bedload transport of fine gravel observed by motion-picture photography, J. Fluid Mech., 192, 193-217. Heald J. McEwan I. Tait, S. 2004 Sediment transport over a flat bed in a unidirectional flow: simulations and validation, Phil. Trans. Roy. Soc. of London A, 362, 1973-1986. Nelson J.M. Shreve R.L. McLean S.R. Drake T.G. 1995 Role of near-bed turbulence structure in bed-load transport and bed form mechanics, Water. Res. Res., 31, 8, 2071-2086.

A New Method for Negative Bias Temperature Instability Assessment in P-Channel Metal Oxide Semiconductor Transistors

NASA Astrophysics Data System (ADS)

Djezzar, Boualem; Tahi, Hakim; Benabdelmoumene, Abdelmadjid; Chenouf, Amel; Kribes, Youcef

2012-11-01

In this paper, we present a new method, named on the fly oxide trap (OTFOT), to extract the bias temperature instability (BTI) in MOS transistors. The OTFOT method is based on charge pumping technique (CP) at low and high frequencies. We emphasize on the theoretical-based concept, giving a clear insight on the easy-use of the OTFOT methodology and demonstrating its viability to characterize the negative BTI (NBTI). Using alternatively high and low frequencies, OTFOT method separates the interface-traps (ΔNit) and border-trap (ΔNbt) (switching oxide-trap) densities independently and also their contributions to the threshold voltage shift (ΔVth), without needing additional methods. The experimental results, from two experimental scenarios, showing the extraction of NBTI-induced shifts caused by interface- and oxide-trap increases are also presented. In the first scenario, all stresses are performed on the same transistor. It exhibits an artifact value of exponent n. In the second scenario, each voltage stress is applied only on one transistor. Its results show an average n of 0.16, 0.05, and 0.11 for NBTI-induced ΔNit, ΔNbt, ΔVth, respectively. Therefore, OTFOT method can contribute to further understand the behavior of the NBTI degradation, especially through the threshold voltage shift components such as ΔVit and ΔVot caused by interface-trap and border-trap, respectively.

Kinematics and dynamics of Nubia-Somalia divergence along the East African rift

NASA Astrophysics Data System (ADS)

Stamps, Dorothy Sarah

Continental rifting is fundamental to the theory of plate tectonics, yet the force balance driving Earth's largest continental rift system, the East African Rift (EAR), remains debated. The EAR actively diverges the Nubian and Somalian plates spanning ˜5000 km N-S from the Red Sea to the Southwest Indian Ridge and ˜3000 km NW-SE from eastern Congo to eastern Madagascar. Previous studies suggest either lithospheric buoyancy forces or horizontal tractions dominate the force balance acting to rupture East Africa. In this work, we investigate the large-scale dynamics of Nubia-Somalia divergence along the EAR driving present-day kinematics. Because Africa is largely surrounded by spreading ridges, we assume plate-plate interactions are minimal and that the major driving forces are gradients in gravitational potential energy (GPE), which includes the effect of vertical mantle tractions, and horizontal basal tractions arising from viscous coupling to horizontal mantle flow. We quantify a continuous strain rate and velocity field based on kinematic models, an updated GPS velocity solution, and the style of earthquake focal mechanisms, which we use as an observational constraint on surface deformation. We solve the 3D force balance equations and calculate vertically averaged deviatoric stress for a 100 km thick lithosphere constrained by the CRUST2.0 crustal density and thickness model. By comparing vertically integrated deviatoric stress with integrated lithospheric strength we demonstrate forces arising from gradients in gravitational potential energy are insufficient to rupture strong lithosphere, hence weakening mechanisms are required to initiate continental rupture. The next step involves inverting for a stress field boundary condition that is the long-wavelength minimum energy deviatoric stress field required to best-fit the style of our continuous strain rate field in addition to deviatoric stress from gradients in GPE. We infer the stress field boundary condition is an estimate of basal shear stress from viscous coupling to horizontal mantle flow. The stress field boundary condition is small (˜1.6 MPa) compared to deviatoric stress from GPE gradients (8-20 MPa) and does not improve the fit to surface deformation indicators more than 8% when combined with deviatoric stress from GPE gradients. Hence we suggest the style of deformation across the EAR can be explained by forces derived from gradients in GPE. We then calculate dynamic velocities using two types of forward models to solve the instantaneous momentum equations. One method is regional and requires vertically averaged effective viscosity to define lithospheric structure with velocity boundary conditions and a free-slip basal boundary condition. The second is a global model that accounts for a brittle upper crust and viscous mantle lithosphere with velocity boundary conditions imposed at the base of the lithosphere from 5 mantle flow models. With both methods we find deformation driven by internal lithospheric buoyancy forces provides the best-fit to GPS observations of surface velocities on the Somalian plate. We find that any additional contribution from horizontal tractions results in overpredicting surface velocities. This work indicates horizontal mantle flow plays a minimal role in Nubia-Somalia divergence and the EAR is driven largely by gradients in GPE.

Surface vapor conductance derived from the ETRHEQ: Dependence on environmental variables and similarity to Oren's stomatal stress model for vapor pressure deficit

NASA Astrophysics Data System (ADS)

Salvucci, G.; Rigden, A. J.

2015-12-01

Daily time series of evapotranspiration and surface conductance to water vapor were estimated using the ETRHEQ method (Evapotranspiration from Relative Humidity at Equilibrium). ETRHEQ has been previously compared with ameriflux site-level measurements of ET at daily and seasonal time scales, with watershed water balance estimates, and with various benchmark ET data sets. The ETRHEQ method uses meteorological data collected at common weather stations and estimates the surface conductance by minimizing the vertical variance of the calculated relative humidity profile averaged over the day. The key advantage of the ETRHEQ method is that it does not require knowledge of the surface state (soil moisture, stomatal conductance, leaf are index, etc.) or site-specific calibration. The daily estimates of conductance from 229 weather stations for 53 years were analyzed for dependence on environmental variables known to impact stomatal conductance and soil diffusivity: surface temperature, surface vapor pressure deficit, solar radiation, antecedent precipitation (as a surrogate for soil moisture), and a seasonal vegetation greenness index. At each site the summertime (JJAS) conductance values estimated from ETRHEQ were fitted to a multiplicate Jarvis-type stress model. Functional dependence was not proscribed, but instead fitted using flexible piecewise-linear splines. The resulting stress functions reproduce the time series of conductance across a wide range of ecosystems and climates. The VPD stress term resembles that proposed by Oren (i.e., 1-m*log(VPD) ), with VPD measured in kilopascals. The equivalent value of m derived from our spline-fits at each station varied over a remarkably small range of 0.58 to 0.62, in agreement with Oren's original analysis based on leaf and tree-level measurements.

Low shear stress gravel-bed river

USGS Publications Warehouse

Milhous, Robert T.

1997-01-01

A low stress gravel bed river is a river where the cross-sectional average dimensionless shear stress (??*) rarely exceeds 0.047. That is the case for the Gunnison River below Delta in Western Colorado. The cross-sectional average ??* in the Gunnison River has not exceeded 0.047, except at one cross section during one year, in the 87 years of record. A ??* of 0.047 is the critical ??* in the bed-load equation considered to be most applicable to gravel/cobble bed rivers (the Meyer-Peter, Mueller equation). According to this equation, there has been no bed-material movement in the Gunnison River since 1920; in fact there has been bed-material movement and this movement is biologically important. Bed-material is moved when the ??* is 0.016 or larger. Streamflows that cause a ??* of at least 0.016 maintain the aquatic habitat in a low shear stress river.

Nonlinear mechanics of composite materials with periodic microstructure

NASA Technical Reports Server (NTRS)

Jordan, E. H.; Walker, K. P.

1991-01-01

This report summarizes the result of research done under NASA NAG3-882 Nonlinear Mechanics of Composites with Periodic Microstructure. The effort involved the development of non-finite element methods to calculate local stresses around fibers in composite materials. The theory was developed and some promising numerical results were obtained. It is expected that when this approach is fully developed, it will provide an important tool for calculating local stresses and averaged constitutive behavior in composites. NASA currently has a major contractual effort (NAS3-24691) to bring the approach developed under this grant to application readiness. The report has three sections. One, the general theory that appeared as a NASA TM, a second section that gives greater details about the theory connecting Greens functions and Fourier series approaches, and a final section shows numerical results.

Fast Physically Accurate Rendering of Multimodal Signatures of Distributed Fracture in Heterogeneous Materials.

PubMed

Visell, Yon

2015-04-01

This paper proposes a fast, physically accurate method for synthesizing multimodal, acoustic and haptic, signatures of distributed fracture in quasi-brittle heterogeneous materials, such as wood, granular media, or other fiber composites. Fracture processes in these materials are challenging to simulate with existing methods, due to the prevalence of large numbers of disordered, quasi-random spatial degrees of freedom, representing the complex physical state of a sample over the geometric volume of interest. Here, I develop an algorithm for simulating such processes, building on a class of statistical lattice models of fracture that have been widely investigated in the physics literature. This algorithm is enabled through a recently published mathematical construction based on the inverse transform method of random number sampling. It yields a purely time domain stochastic jump process representing stress fluctuations in the medium. The latter can be readily extended by a mean field approximation that captures the averaged constitutive (stress-strain) behavior of the material. Numerical simulations and interactive examples demonstrate the ability of these algorithms to generate physically plausible acoustic and haptic signatures of fracture in complex, natural materials interactively at audio sampling rates.

High Self-Perceived Stress and Poor Coping in Intellectually Able Adults with Autism Spectrum Disorder

ERIC Educational Resources Information Center

Hirvikoski, Tatja; Blomqvist, My

2015-01-01

Despite average intellectual capacity, autistic traits may complicate performance in many everyday situations, thus leading to stress. This study focuses on stress in everyday life in intellectually able adults with autism spectrum disorders. In total, 53 adults (25 with autism spectrum disorder and 28 typical adults from the general population)…

Relationships among Perceived Stress, Coping, and Grade Point Average in University Students

ERIC Educational Resources Information Center

Kewallal, Rajendra David

2013-01-01

This study explored the relationships among perceived stress, coping style, and academic performance in 210 students from a mid-sized public university and a small private college. Study participants were asked to complete the Perceived Stress Scale, the Brief COPE Questionnaire, and a demographic survey asking about their age, gender, grade point…

The Effect of Perfectionism and Acculturative Stress on Levels of Depression Experienced by East Asian International Students

ERIC Educational Resources Information Center

Hamamura, Toshitaka; Laird, Philip G.

2014-01-01

This study examined relationships among acculturative stress, grade point average satisfaction, maladaptive perfectionism, and depression in 52 East Asian international students and 126 North American students. Results indicated that a combined effect of perfectionism and acculturative stress accounted for more than 30% of the variance related to…

Stress, Social Support, and Health among College Students after September 11, 2001

ERIC Educational Resources Information Center

MacGeorge, Erina L.; Samter, Wendy; Feng, Bo; Gillihan, Seth J.; Graves, Angela R.

2004-01-01

The current study was designed to examine associations among stress due to the 9/11 terrorist attacks, social support, and health (depression and physical illness) in a college student sample. In December 2001, students from Eastern universities (N = 666; 482 women, 184 men; average age 19.5 yrs.) completed measures of stress from terrorism…

Predicting Secondary Agriculture Teachers' Job Stress from Selected Personal, Family, and Work-Related Characteristics

ERIC Educational Resources Information Center

Torres, Robert M.; Lambert, Misty D.; Lawver, Rebecca G.

2010-01-01

The study sought to describe the characteristics and explain the current level of job stress among secondary agriculture teachers. The sample consisted of 370 secondary agriculture teachers. Data were collected using the Job Stress Survey (Spielberger & Vagg, 1999). From the findings it was concluded that the average secondary agriculture teacher…

Geohydrology and numerical simulation of the alluvium and terrace aquifer along the Beaver-North Canadian River from the Panhandle to Canton Lake, northwestern Oklahoma

USGS Publications Warehouse

Davis, Robert E.; Christenson, Scott C.

1981-01-01

A quantitative description of the hydrologic system in alluvium and terrace deposits along the Beaver-North Canadian River in northwestern Oklahoma is needed as an aid for planning and management of the aquifer. A two-dimensional finite-difference model was used to describe the aquifer and to predict the effects of future ground-water withdrawals.The aquifer principally consists of three geologic units: Alluvium with an average thickness of 30 feet, low terrace deposits with an average thickness of 50 feet, and high terrace deposits with an average thickness of 70 feet. A thin cover of dune sand overlies much of the area and provides an excellent catchment for recharge, but is generally unsaturated.Hydraulic conductivity of the aquifer ranges from 0 to 160 feet per day and averages 59 feet per day. Specific yield is estimated to be 0.29. Recharge to the aquifer is approximately 1 inch annually. Under present conditions (1978), most discharge is the result of ground-water flow to the Beaver-North Canadian River at a rate of 36 cubic feet per second and to pumpage for public-supply, industrial, and irrigation use at a rate of 28 cubic feet per second. In 1978, the aquifer had an average saturated thickness of 31 feet and contained 4.07 million acre-feet of water.The model was used to predict future head response in the aquifer to various pumping stresses. For any one area, the pumping stress was applied until the saturated thickness for that area was less than 5 feet, at which time the pumping ceased.The results of the modeled projections show that if the aquifer is stressed from 1978 to 1993 at the 1977 pumpage rates and well distribution, the average saturated thickness will decrease 1.0 foot and the volume of water in storage will be 3.94 million acre-feet, or 97 percent of the 1978 volume. If the aquifer is stressed at this same rate until 2020, the average saturated thickness will decrease an additional 0.7 foot and the volume of water in storage will be 3.84 million acre-feet, or 94 percent of the 1978 volume.If all areas of the aquifer having a 1978 saturated thickness of 5 feet or more are stressed from 1978 to 1993 at a rate of approximately1.4 acre-feet per acre per year, the average saturated thickness will decrease by 20.9 feet and the volume of water in storage will be 1.28 million acre-feet, or 31 percent of the 1978 volume. If the aquifer is stressed at this same rate until 2020, the average saturated thickness will decrease an additional 2.2 feet and the volume of water in storage will be 980,000 acre-feet, or 24 percent of the 1978 volume.The water in the aquifer is generally of the calcium bicarbonate type and is suitable for most uses. Most of the 30 water samples analyzed contained less than 500 milligrams of dissolved solids per liter.

Occupational Stress and Physical Symptoms among Family Medicine Residents

PubMed Central

Choi, So-Myung; Park, Yong Soon; Kim, Go-Young

2013-01-01

Background The purpose of this study was to examine the levels of occupational stress and physical symptoms among family medicine residents and investigate the effect of subscales of occupational stress on physical symptoms. Methods A self-administered questionnaire survey of 1,152 family medicine residents was carried out via e-mail from April 2010 to July 2010. The response rate was 13.1% and the R (ver. 2.9.1) was used for the analysis of completed data obtained from 150 subjects. The questionnaire included demographic factors, resident training related factors, 24-items of the Korean Occupational Stress Scales and Korean Versions of the Wahler Physical Symptom Inventory. Results The total score of occupational stress of family medicine residents was relatively low compared to that of average workers. The scores of 'high job demand', 'inadequate social support', 'organizational injustice', and 'discomfort in occupational climate' were within the top 50%. Parameters associated with higher occupational stress included level of training, on-duty time, daily patient load, critical patient assigned, total working days, night duty day, sleep duration, and sleep quality. The six subscales of occupational stress, except for 'Job insecurity', had a significant positive correlation with physical symptom scores after adjustment had been made for potential confounders (total score, r = 0.325 and P < 0.001; high job demand, r = 0.439 and P < 0.001). Conclusion After the adjustment had been made for potential confounders, the total score of occupational stress and six subscales in family medicine residents showed a significant positive correlation with physical symptom scores. PMID:23372906

Speckle techniques for determining stresses in moving objects

NASA Technical Reports Server (NTRS)

Murphree, E. A.; Wilson, T. F.; Ranson, W. F.; Swinson, W. F.

1978-01-01

Laser speckle interferometry is a relatively new experimental technique which shows promise of alleviating many difficult problems in experimental mechanics. The method utilizes simple high-resolution photographs of the surface which is illuminated by coherent light. The result is a real-time or permanently stored whole-field record of interference fringes which yields a map of displacements in the object. In this thesis, the time-average theory using the Fourier transform is developed to present the application of this technique to measurement of in-plane displacement induced by the vibration of an object.

Summary of EASM Turbulence Models in CFL3D With Validation Test Cases

NASA Technical Reports Server (NTRS)

Rumsey, Christopher L.; Gatski, Thomas B.

2003-01-01

This paper summarizes the Explicit Algebraic Stress Model in k-omega form (EASM-ko) and in k-epsilon form (EASM-ke) in the Reynolds-averaged Navier-Stokes code CFL3D. These models have been actively used over the last several years in CFL3D, and have undergone some minor modifications during that time. Details of the equations and method for coding the latest versions of the models are given, and numerous validation cases are presented. This paper serves as a validation archive for these models.

Temperature Dependence on the Strength and Stress Rupture Behavior of a Carbon-Fiber Reinforced Silicon Carbide (C/SiC) Composite

NASA Technical Reports Server (NTRS)

Verrilli, Michael J.; Calomino, Anthony

2002-01-01

Tensile strengths and stress rupture lives of carbon-fiber reinforced silicon carbide (C/SiC) specimens were measured at 800 C and are compared to previously reported 1200 C data. All tests were conducted in an environmental chamber containing 1000 ppm of oxygen in argon. The average 800 C tensile strength of 610 MPa is 10% greater than at 1200 C. Average stress rupture lives at 800 C were 2.5 times longer than those obtained at 1200 C. The difference in the 800 and 1200 C lives is related to the oxidation rate of the reinforcing carbon fibers, which is the primary damage mode of C/SiC composites in oxygen-containing environments.

Observed source parameters for dynamic rupture with non-uniform initial stressand relatively high fracture energy

USGS Publications Warehouse

Beeler, Nicholas M.; Kilgore, Brian D.; McGarr, Arthur F.; Fletcher, Jon Peter B.; Evans, John R.; Steven R. Baker,

2012-01-01

We have conducted dynamic rupture propagation experiments to establish the relations between in-source stress drop, fracture energy and the resulting particle velocity during slip of an unconfined 2 m long laboratory fault at normal stresses between 4 and 8 MPa. To produce high fracture energy in the source we use a rough fault that has a large slip weakening distance. An artifact of the high fracture energy is that the nucleation zone is large such that precursory slip reduces fault strength over a large fraction of the total fault length prior to dynamic rupture, making the initial stress non-uniform. Shear stress, particle velocity, fault slip and acceleration were recorded coseismically at multiple locations along strike and at small fault-normal distances. Stress drop increases weakly with normal stress. Average slip rate depends linearly on the fault strength loss and on static stress drop, both with a nonzero intercept. A minimum fracture energy of 1.8 J/m2 and a linear slip weakening distance of 33 μm are inferred from the intercept. The large slip weakening distance also affects the average slip rate which is reduced by in-source energy dissipation from on-fault fracture energy.Because of the low normal stress and small per event slip (∼86 μm), no thermal weakening such as melting or pore fluid pressurization occurs in these experiments. Despite the relatively high fracture energy, and the very low heat production, energy partitioning during these laboratory earthquakes is very similar to typical earthquake source properties. The product of fracture energy and fault area is larger than the radiated energy. Seismic efficiency is low at ∼2%. The ratio of apparent stress to static stress drop is ∼27%, consistent with measured overshoot. The fracture efficiency is ∼33%. The static and dynamic stress drops when extrapolated to crustal stresses are 2–7.3 MPa and in the range of typical earthquake stress drops. As the relatively high fracture energy reduces the slip velocities in these experiments, the extrapolated average particle velocities for crustal stresses are 0.18–0.6 m/s. That these experiments are consistent with typical earthquake source properties suggests, albeit indirectly, that thermal weakening mechanisms such as thermal pressurization and melting which lead to near complete stress drops, dominate earthquake source properties only for exceptional events unless crustal stresses are low.

Study on electromagnetic radiation and mechanical characteristics of coal during an SHPB test

NASA Astrophysics Data System (ADS)

Chengwu, Li; Qifei, Wang; Pingyang, Lyu

2016-06-01

Dynamic loads provided by a Split Hopkinson pressure bar are applied in the impact failure experiment on coal with an impact velocity of 4.174-17.652 m s-1. The mechanical property characteristics of coal and an electromagnetic radiation signal can be detected and measured during the experiment. The variation of coal stress, strain, incident energy, dissipated energy and other mechanical parameters are analyzed by the unidimensional stress wave theory. It suggests that with an increase of the impact velocity, the mechanical parameters and electromagnetic radiation increased significantly and the dissipated energy of the coal sample has a high discrete growing trend during the failure process of coal impact. Combined with the received energy of the electromagnetic radiation signal, the relationship between these mechanical parameters and electromagnetic radiation during the failure process of coal burst could be analyzed by the grey correlation model. The results show that the descending order of the gray correlation degree between the mechanical characteristics and electromagnetic radiation energy are impact velocity, maximum stress, the average stress, incident energy, the average strain, maximum strain, the average strain rate and dissipation energy. Due to the correlation degree, the impact velocity and incident energy are relatively large, and the main factor affecting the electromagnetic radiation energy of coal is the energy magnitude. While the relationship between extreme stress and the radiation energy change trend is closed, the stress state of coal has a greater impact on electromagnetic radiation than the strain and destruction which can deepen the research of the coal-rock dynamic disaster electromagnetic monitoring technique.

Material Properties from Air Puff Corneal Deformation by Numerical Simulations on Model Corneas

PubMed Central

Dorronsoro, Carlos; de la Hoz, Andrés; Marcos, Susana

2016-01-01

Objective To validate a new method for reconstructing corneal biomechanical properties from air puff corneal deformation images using hydrogel polymer model corneas and porcine corneas. Methods Air puff deformation imaging was performed on model eyes with artificial corneas made out of three different hydrogel materials with three different thicknesses and on porcine eyes, at constant intraocular pressure of 15 mmHg. The cornea air puff deformation was modeled using finite elements, and hyperelastic material parameters were determined through inverse modeling, minimizing the difference between the simulated and the measured central deformation amplitude and central-peripheral deformation ratio parameters. Uniaxial tensile tests were performed on the model cornea materials as well as on corneal strips, and the results were compared to stress-strain simulations assuming the reconstructed material parameters. Results The measured and simulated spatial and temporal profiles of the air puff deformation tests were in good agreement (< 7% average discrepancy). The simulated stress-strain curves of the studied hydrogel corneal materials fitted well the experimental stress-strain curves from uniaxial extensiometry, particularly in the 0–0.4 range. Equivalent Young´s moduli of the reconstructed material properties from air-puff were 0.31, 0.58 and 0.48 MPa for the three polymer materials respectively which differed < 1% from those obtained from extensiometry. The simulations of the same material but different thickness resulted in similar reconstructed material properties. The air-puff reconstructed average equivalent Young´s modulus of the porcine corneas was 1.3 MPa, within 18% of that obtained from extensiometry. Conclusions Air puff corneal deformation imaging with inverse finite element modeling can retrieve material properties of model hydrogel polymer corneas and real corneas, which are in good correspondence with those obtained from uniaxial extensiometry, suggesting that this is a promising technique to retrieve quantitative corneal biomechanical properties. PMID:27792759

A new culture system for in situ observation of the growth and development of Eucyclops serrulatus (Copepoda: Cyclopoida)

PubMed Central

Park, Sung-Hee; Chang, Cheon-Young

2005-01-01

A practical and convenient method of rearing Eucyclops serrulatus in a microculture environment is described. A complete life cycle of E. serrulatus was maintained in a narrow space on a microscope slide glass on which a cover glass of 22 x 40 mm in size was mounted at a height of 0.8 mm. The culture medium was constituted by bottled mineral water boiled with grains of Glycine max (soybean). Chilomonas paramecium, a free-living protozoan organism, was provided as live food. Growth of nauplii hatched from eggs to the first stage of copepodite took an average of 7.7 days, and the growth of copepodite 1 to the egg-bearing adult female took an average of 20.1 days in the microculture cell with an average life time of 44.7 days. Continuous passage of copepods was successfully maintained as long as sufficient medium and food were provided. The microculture method enables an in situ microscopic observation on the growth and developmental process of helminth larvae experimentally infected to copepods as well as of copepod itself. Furthermore, it does not require anesthetization and, therefore, minimize the amount of stress exposed to copepods during the handling process. PMID:16340303

Telomere Length, Current Perceived Stress, and Urinary Stress Hormones in Women

PubMed Central

Parks, Christine G.; Miller, Diane B.; McCanlies, Erin C.; Cawthon, Richard M.; Andrew, Michael E.; DeRoo, Lisa A.; Sandler, Dale P.

2009-01-01

Telomeres are repetitive DNA sequences that cap and protect the ends of chromosomes; critically short telomeres may lead to cellular senescence or carcinogenic transformation. Previous findings suggest a link between psychosocial stress, shorter telomeres, and chronic disease risk. This cross-sectional study examined relative telomere length in relation to perceived stress and urinary stress hormones in a sample of participants (n = 647) in the National Institute of Environmental Health Sciences Sister Study, a cohort of women ages 35 to 74 years who have a sister with breast cancer. Average leukocyte telomere length was determined by quantitative PCR. Current stress was assessed using the Perceived Stress Scale and creatinine-adjusted neuroendocrine hormones in first morning urines. Linear regression models estimated differences in telomere length base pairs (bp) associated with stress measures adjusted for age, race, smoking, and obesity. Women with higher perceived stress had somewhat shorter telomeres [adjusted difference of −129bp for being at or above moderate stress levels; 95% confidence interval (CI), −292 to 33], but telomere length did not decrease monotonically with higher stress levels. Shorter telomeres were independently associated with increasing age (−27bp/year), obesity, and current smoking. Significant stress-related differences in telomere length were seen in women ages 55 years and older (−289bp; 95% CI, −519 to −59), those with recent major losses (−420bp; 95% CI, −814 to −27), and those with above-average urinary catecholamines (e.g., epinephrine: −484bp; 95% CI, −709 to −259). Although current perceived stress was only modestly associated with shorter telomeres in this broad sample of women, our findings suggest the effect of stress on telomere length may vary depending on neuroendocrine responsiveness, external stressors, and age. PMID:19190150

Compressible Boundary Layer Predictions at High Reynolds Number using Hybrid LES/RANS Methods

NASA Technical Reports Server (NTRS)

Choi, Jung-Il; Edwards, Jack R.; Baurle, Robert A.

2008-01-01

Simulations of compressible boundary layer flow at three different Reynolds numbers (Re(sub delta) = 5.59x10(exp 4), 1.78x10(exp 5), and 1.58x10(exp 6) are performed using a hybrid large-eddy/Reynolds-averaged Navier-Stokes method. Variations in the recycling/rescaling method, the higher-order extension, the choice of primitive variables, the RANS/LES transition parameters, and the mesh resolution are considered in order to assess the model. The results indicate that the present model can provide good predictions of the mean flow properties and second-moment statistics of the boundary layers considered. Normalized Reynolds stresses in the outer layer are found to be independent of Reynolds number, similar to incompressible turbulent boundary layers.

Timing of favorable conditions, competition and fertility interact to govern recruitment of invasive Chinese tallow tree in stressful environments.

PubMed

Gabler, Christopher A; Siemann, Evan

2013-01-01

The rate of new exotic recruitment following removal of adult invaders (reinvasion pressure) influences restoration outcomes and costs but is highly variable and poorly understood. We hypothesize that broad variation in average reinvasion pressure of Triadica sebifera (Chinese tallow tree, a major invader) arises from differences among habitats in spatiotemporal availability of realized recruitment windows. These windows are periods of variable duration long enough to permit establishment given local environmental conditions. We tested this hypothesis via a greenhouse mesocosm experiment that quantified how the duration of favorable moisture conditions prior to flood or drought stress (window duration), competition and nutrient availability influenced Triadica success in high stress environments. Window duration influenced pre-stress seedling abundance and size, growth during stress and final abundance; it interacted with other factors to affect final biomass and germination during stress. Stress type and competition impacted final size and biomass, plus germination, mortality and changes in size during stress. Final abundance also depended on competition and the interaction of window duration, stress type and competition. Fertilization interacted with competition and stress to influence biomass and changes in height, respectively, but did not affect Triadica abundance. Overall, longer window durations promoted Triadica establishment, competition and drought (relative to flood) suppressed establishment, and fertilization had weak effects. Interactions among factors frequently produced different effects in specific contexts. Results support our 'outgrow the stress' hypothesis and show that temporal availability of abiotic windows and factors that influence growth rates govern Triadica recruitment in stressful environments. These findings suggest that native seed addition can effectively suppress superior competitors in stressful environments. We also describe environmental scenarios where specific management methods may be more or less effective. Our results enable better niche-based estimates of local reinvasion pressure, which can improve restoration efficacy and efficiency by informing site selection and optimal management.

Continuous Rapid Quantification of Stroke Volume using Magnetohydrodynamic Voltages in 3T MRI

PubMed Central

Gregory, T. Stan; Oshinski, John; Schmidt, Ehud J.; Kwong, Raymond Y.; Stevenson, William G.; Tse, Zion Tsz Ho

2015-01-01

Background To develop a technique to non-invasively estimate Stroke Volume (SV) in real-time during Magnetic Resonance Imaging (MRI) guided procedures, based on induced Magnetohydrodynamic Voltages (VMHD) that occur in Electrocardiogram (ECG) recordings during MRI exams, leaving the MRI scanner free to perform other imaging tasks. Due to the relationship between blood-flow (BF) and VMHD, we hypothesized that a method to obtain SV could be derived from extracted VMHD vectors in the Vectorcardiogram frame-of-reference (VMHDVCG). Methods and Results To estimate a subject-specific BF-VMHD model, VMHDVCG was acquired during a 20-second breath-hold and calibrated versus aortic BF measured using Phase Contrast Magnetic Resonance (PCMR) in 10 subjects (n=10) and one subject diagnosed with Premature Ventricular Contractions (PVCs). Beat-to-Beat validation of VMHDVCG derived BF was performed using Real-Time Phase Contrast (RTPC) imaging in 7 healthy subjects (n=7) during a 15 minute cardiac exercise stress tests and 30 minutes after stress relaxation in 3T MRIs. Subject-specific equations were derived to correlate VMHDVCG to BF at rest, and validated using RTPC. An average error of 7.22% and 3.69% in SV estimation, respectively, was found during peak stress, and after complete relaxation. Measured beat-to-beat blood flow time-history derived from RTPC and VMHD were highly correlated using a Spearman Rank Correlation Coefficient during stress tests (0.89) and after stress relaxation (=0.86). Conclusions Accurate beat-to-beat SV and BF were estimated using VMHDVCG extracted from intra-MRI 12-lead ECGs, providing a means to enhance patient monitoring during MR imaging and MR-guided interventions. PMID:26628581

Thermal hydraulic design and decay heat removal of a solid target for a spallation neutron source

NASA Astrophysics Data System (ADS)

Takenaka, N.; Nio, D.; Kiyanagi, Y.; Mishima, K.; Kawai, M.; Furusaka, M.

2005-08-01

Thermal hydraulic design and thermal stress calculations were conducted for a water-cooled solid target irradiated by a MW-class proton beam for a spallation neutron source. Plate type and rod bundle type targets were examined. The thickness of the plate and the diameter of the rod were determined based on the maximum and the wall surface temperature. The thermal stress distributions were calculated by a finite element method (FEM). The neutronics performance of the target is roughly proportional to its average density. The averaged densities of the designed targets were calculated for tungsten plates, tantalum clad tungsten plates, tungsten rods sheathed by tantalum and Zircaloy and they were compared with mercury density. It was shown that the averaged density was highest for the tungsten plates and was high for the tantalum cladding tungsten plates, the tungsten rods sheathed by tantalum and Zircaloy in order. They were higher than or equal to that of mercury for the 1 2 MW proton beams. Tungsten target without the cladding or the sheath is not practical due to corrosion by water under irradiation condition. Therefore, the tantalum cladding tungsten plate already made successfully by HIP and the sheathed tungsten rod are the candidate of high performance solid targets. The decay heat of each target was calculated. It was low enough low compared to that of ISIS for the target without tantalum but was about four times as high as that of ISIS when the thickness of the tantalum cladding was 0.5 mm. Heat removal methods of the decay heat with tantalum were examined. It was shown that a special cooling system was required for the target exchange when tantalum was used for the target. It was concluded that the tungsten rod target sheathed with stainless steel or Zircaloy was the most reliable from the safety considerations and had similar neutronics performance to that of mercury.

Incidence and prevalence of elite male cricket injuries using updated consensus definitions

PubMed Central

Orchard, John W; Kountouris, Alex; Sims, Kevin

2016-01-01

Background T20 (Twenty20 or 20 over) cricket has emerged in the last decade as the most popular form of cricket (in terms of spectator attendances). International consensus cricket definitions, first published in 2005, were updated in 2016 to better reflect the rise to prominence of T20 cricket. Methods Injury incidence and prevalence rates were calculated using the new international methods and units for elite senior male Australian cricketers over the past decade (season 2006–2007 to season 2015–2016 inclusive). Results Over the past 10 seasons, average match injury incidence, for match time-loss injuries, was 155 injuries/1,000 days of play, with the highest daily rates in 50-over cricket, followed by 20-over cricket and First-Class matches. Annual injury incidence was 64 injuries/100 players per season, and average annual injury prevalence was 12.5% (although fast bowlers averaged 20.6%, much higher than other positions). The most common injury was the hamstring strain (seasonal incidence 8.7 injuries/100 players per season). The most prevalent injury was lumbar stress fractures (1.9% of players unavailable at all times owing to these injuries, which represents 15% of all missed playing time). Discussion The hamstring strain has emerged from being one of the many common injuries in elite cricket a decade ago to being clearly the most common injury in the sport at the elite level. This is presumably in association with increased T20 cricket. Lumbar stress fractures in fast bowlers are still the most prevalent injury in the sport of cricket at the elite level, although these injuries are more associated with high workloads arising from the longer forms of the game. Domestic and international matches have very similar match injury incidence rates across the formats, but injury prevalence is higher in international players as they play for most of the year without a substantial off-season. PMID:28008292

Traction force microscopy in rapidly moving cells reveals separate roles for ROCK and MLCK in the mechanics of retraction.

PubMed

Morin, Timothy R; Ghassem-Zadeh, Sean A; Lee, Juliet

2014-08-15

Retraction is a major rate-limiting step in cell motility, particularly in slow moving cell types that form large stable adhesions. Myosin II dependent contractile forces are thought to facilitate detachment by physically pulling up the rear edge. However, retraction can occur in the absence of myosin II activity in cell types that form small labile adhesions. To investigate the role of contractile force generation in retraction, we performed traction force microscopy during the movement of fish epithelial keratocytes. By correlating changes in local traction stress at the rear with the area retracted, we identified four distinct modes of retraction. "Recoil" retractions are preceded by a rise in local traction stress, while rear edge is temporarily stuck, followed by a sharp drop in traction stress upon detachment. This retraction type was most common in cells generating high average traction stress. In "pull" type retractions local traction stress and area retracted increase concomitantly. This was the predominant type of retraction in keratocytes and was observed mostly in cells generating low average traction stress. "Continuous" type retractions occur without any detectable change in traction stress, and are seen in cells generating low average traction stress. In contrast, to many other cell types, "release" type retractions occur in keratocytes following a decrease in local traction stress. Our identification of distinct modes of retraction suggests that contractile forces may play different roles in detachment that are related to rear adhesion strength. To determine how the regulation of contractility via MLCK or Rho kinase contributes to the mechanics of detachment, inhibitors were used to block or augment these pathways. Modulation of MLCK activity led to the most rapid change in local traction stress suggesting its importance in regulating attachment strength. Surprisingly, Rho kinase was not required for detachment, but was essential for localizing retraction to the rear. We suggest that in keratocytes MLCK and Rho kinase play distinct, complementary roles in the respective temporal and spatial control of rear detachment that is essential for maintaining rapid motility. Copyright © 2014 Elsevier Inc. All rights reserved.

Skin-Friction Measurements in Incompressible Flow

NASA Technical Reports Server (NTRS)

Smith, Donald W.; Walker, John H.

1959-01-01

Experiments have been conducted to measure the local surface-shear stress and the average skin-friction coefficient in Incompressible flow for a turbulent boundary layer on a smooth flat plate having zero pressure gradient. Data were obtained for a range of Reynolds numbers from 1 million to 45 million. The local surface-shear stress was measured by a floating-element skin-friction balance and also by a calibrated total head tube located on the surface of the test wall. The average skin-friction coefficient was obtained from boundary-layer velocity profiles.

Towards the Irving-Kirkwood limit of the mechanical stress tensor

NASA Astrophysics Data System (ADS)

Smith, E. R.; Heyes, D. M.; Dini, D.

2017-06-01

The probability density functions (PDFs) of the local measure of pressure as a function of the sampling volume are computed for a model Lennard-Jones (LJ) fluid using the Method of Planes (MOP) and Volume Averaging (VA) techniques. This builds on the study of Heyes, Dini, and Smith [J. Chem. Phys. 145, 104504 (2016)] which only considered the VA method for larger subvolumes. The focus here is typically on much smaller subvolumes than considered previously, which tend to the Irving-Kirkwood limit where the pressure tensor is defined at a point. The PDFs from the MOP and VA routes are compared for cubic subvolumes, V =ℓ3. Using very high grid-resolution and box-counting analysis, we also show that any measurement of pressure in a molecular system will fail to exactly capture the molecular configuration. This suggests that it is impossible to obtain the pressure in the Irving-Kirkwood limit using the commonly employed grid based averaging techniques. More importantly, below ℓ ≈3 in LJ reduced units, the PDFs depart from Gaussian statistics, and for ℓ =1.0 , a double peaked PDF is observed in the MOP but not VA pressure distributions. This departure from a Gaussian shape means that the average pressure is not the most representative or common value to arise. In addition to contributing to our understanding of local pressure formulas, this work shows a clear lower limit on the validity of simply taking the average value when coarse graining pressure from molecular (and colloidal) systems.

Towards the Irving-Kirkwood limit of the mechanical stress tensor.

PubMed

Smith, E R; Heyes, D M; Dini, D

2017-06-14

The probability density functions (PDFs) of the local measure of pressure as a function of the sampling volume are computed for a model Lennard-Jones (LJ) fluid using the Method of Planes (MOP) and Volume Averaging (VA) techniques. This builds on the study of Heyes, Dini, and Smith [J. Chem. Phys. 145, 104504 (2016)] which only considered the VA method for larger subvolumes. The focus here is typically on much smaller subvolumes than considered previously, which tend to the Irving-Kirkwood limit where the pressure tensor is defined at a point. The PDFs from the MOP and VA routes are compared for cubic subvolumes, V=ℓ 3 . Using very high grid-resolution and box-counting analysis, we also show that any measurement of pressure in a molecular system will fail to exactly capture the molecular configuration. This suggests that it is impossible to obtain the pressure in the Irving-Kirkwood limit using the commonly employed grid based averaging techniques. More importantly, below ℓ≈3 in LJ reduced units, the PDFs depart from Gaussian statistics, and for ℓ=1.0, a double peaked PDF is observed in the MOP but not VA pressure distributions. This departure from a Gaussian shape means that the average pressure is not the most representative or common value to arise. In addition to contributing to our understanding of local pressure formulas, this work shows a clear lower limit on the validity of simply taking the average value when coarse graining pressure from molecular (and colloidal) systems.

Towards the Irving-Kirkwood limit of the mechanical stress tensor

PubMed Central

Heyes, D. M.; Dini, D.

2017-01-01

The probability density functions (PDFs) of the local measure of pressure as a function of the sampling volume are computed for a model Lennard-Jones (LJ) fluid using the Method of Planes (MOP) and Volume Averaging (VA) techniques. This builds on the study of Heyes, Dini, and Smith [J. Chem. Phys. 145, 104504 (2016)] which only considered the VA method for larger subvolumes. The focus here is typically on much smaller subvolumes than considered previously, which tend to the Irving-Kirkwood limit where the pressure tensor is defined at a point. The PDFs from the MOP and VA routes are compared for cubic subvolumes, V=ℓ3. Using very high grid-resolution and box-counting analysis, we also show that any measurement of pressure in a molecular system will fail to exactly capture the molecular configuration. This suggests that it is impossible to obtain the pressure in the Irving-Kirkwood limit using the commonly employed grid based averaging techniques. More importantly, below ℓ≈3 in LJ reduced units, the PDFs depart from Gaussian statistics, and for ℓ=1.0, a double peaked PDF is observed in the MOP but not VA pressure distributions. This departure from a Gaussian shape means that the average pressure is not the most representative or common value to arise. In addition to contributing to our understanding of local pressure formulas, this work shows a clear lower limit on the validity of simply taking the average value when coarse graining pressure from molecular (and colloidal) systems. PMID:29166053

75 FR 2067 - Airworthiness Directives; Turbomeca S.A. Model Arriel 1B, 1D, and 1D1 Turboshaft Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-14

... originated at the pinion teeth root due to increased vibratory stresses. This increase in vibratory stresses... reduce the level of vibratory stresses and improve tooth resistance, Turbom[eacute]ca modification... estimate that it would take about 6 work-hours per product to comply with this AD. The average labor rate...

Predicting boundary shear stress and sediment transport over bed forms

USGS Publications Warehouse

McLean, S.R.; Wolfe, S.R.; Nelson, J.M.

1999-01-01

To estimate bed-load sediment transport rates in flows over bed forms such as ripples and dunes, spatially averaged velocity profiles are frequently used to predict mean boundary shear stress. However, such averaging obscures the complex, nonlinear interaction of wake decay, boundary-layer development, and topographically induced acceleration downstream of flow separation and often leads to inaccurate estimates of boundary stress, particularly skin friction, which is critically important in predicting bed-load transport rates. This paper presents an alternative methodology for predicting skin friction over 2D bed forms. The approach is based on combining the equations describing the mechanics of the internal boundary layer with semiempirical structure functions to predict the velocity at the crest of a bedform, where the flow is most similar to a uniform boundary layer. Significantly, the methodology is directed toward making specific predictions only at the bed-form crest, and as a result it avoids the difficulty and questionable validity of spatial averaging. The model provides an accurate estimate of the skin friction at the crest where transport rates are highest. Simple geometric constraints can be used to derive the mean transport rates as long as bed load is dominant.To estimate bed-load sediment transport rates in flows over bed forms such as ripples and dunes, spatially averaged velocity profiles are frequently used to predict mean boundary shear stress. However, such averaging obscures the complex, nonlinear interaction of wake decay, boundary-layer development, and topographically induced acceleration downstream of flow separation and often leads to inaccurate estimates of boundary stress, particularly skin friction, which is critically important in predicting bed-load transport rates. This paper presents an alternative methodology for predicting skin friction over 2D bed forms. The approach is based on combining the equations describing the mechanics of the internal boundary layer with semiempirical structure functions to predict the velocity at the crest of a bedform, where the flow is most similar to a uniform boundary layer. Significantly, the methodology is directed toward making specific predictions only at the bed-form crest, and as a result it avoids the difficulty and questionable validity of spatial averaging. The model provides an accurate estimate of the skin friction at the crest where transport rates are highest. Simple geometric constraints can be used to derive the mean transport rates as long as bed load is dominant.

Estimating hydraulic properties using a moving-model approach and multiple aquifer tests

USGS Publications Warehouse

Halford, K.J.; Yobbi, D.

2006-01-01

A new method was developed for characterizing geohydrologic columns that extended >600 m deep at sites with as many as six discrete aquifers. This method was applied at 12 sites within the Southwest Florida Water Management District. Sites typically were equipped with multiple production wells, one for each aquifer and one or more observation wells per aquifer. The average hydraulic properties of the aquifers and confining units within radii of 30 to >300 m were characterized at each site. Aquifers were pumped individually and water levels were monitored in stressed and adjacent aquifers during each pumping event. Drawdowns at a site were interpreted using a radial numerical model that extended from land surface to the base of the geohydrologic column and simulated all pumping events. Conceptually, the radial model moves between stress periods and recenters on the production well during each test. Hydraulic conductivity was assumed homogeneous and isotropic within each aquifer and confining unit. Hydraulic property estimates for all of the aquifers and confining units were consistent and reasonable because results from multiple aquifers and pumping events were analyzed simultaneously. Copyright ?? 2005 National Ground Water Association.

Computational fluid dynamics challenges for hybrid air vehicle applications

NASA Astrophysics Data System (ADS)

Carrin, M.; Biava, M.; Steijl, R.; Barakos, G. N.; Stewart, D.

2017-06-01

This paper begins by comparing turbulence models for the prediction of hybrid air vehicle (HAV) flows. A 6 : 1 prolate spheroid is employed for validation of the computational fluid dynamics (CFD) method. An analysis of turbulent quantities is presented and the Shear Stress Transport (SST) k-ω model is compared against a k-ω Explicit Algebraic Stress model (EASM) within the unsteady Reynolds-Averaged Navier-Stokes (RANS) framework. Further comparisons involve Scale Adaptative Simulation models and a local transition transport model. The results show that the flow around the vehicle at low pitch angles is sensitive to transition effects. At high pitch angles, the vortices generated on the suction side provide substantial lift augmentation and are better resolved by EASMs. The validated CFD method is employed for the flow around a shape similar to the Airlander aircraft of Hybrid Air Vehicles Ltd. The sensitivity of the transition location to the Reynolds number is demonstrated and the role of each vehicle£s component is analyzed. It was found that the ¦ns contributed the most to increase the lift and drag.

Estimating hydraulic properties using a moving-model approach and multiple aquifer tests.

PubMed

Halford, Keith J; Yobbi, Dann

2006-01-01

A new method was developed for characterizing geohydrologic columns that extended >600 m deep at sites with as many as six discrete aquifers. This method was applied at 12 sites within the Southwest Florida Water Management District. Sites typically were equipped with multiple production wells, one for each aquifer and one or more observation wells per aquifer. The average hydraulic properties of the aquifers and confining units within radii of 30 to >300 m were characterized at each site. Aquifers were pumped individually and water levels were monitored in stressed and adjacent aquifers during each pumping event. Drawdowns at a site were interpreted using a radial numerical model that extended from land surface to the base of the geohydrologic column and simulated all pumping events. Conceptually, the radial model moves between stress periods and recenters on the production well during each test. Hydraulic conductivity was assumed homogeneous and isotropic within each aquifer and confining unit. Hydraulic property estimates for all of the aquifers and confining units were consistent and reasonable because results from multiple aquifers and pumping events were analyzed simultaneously.

Perceived Stress and Coffee and Energy Drink Consumption Predict Poor Sleep Quality in Podiatric Medical Students A Cross-sectional Study.

PubMed

Sawah, Mohomad Al; Ruffin, Naeemah; Rimawi, Mohammad; Concerto, Carmen; Aguglia, Eugenio; Chusid, Eileen; Infortuna, Carmenrita; Battaglia, Fortunato

2015-09-01

A cross-sectional survey administered to first- and second-year podiatric medical students aimed to investigate the effect of coffee intake, energy drink consumption, and perceived stress on sleep quality in medical students during their preclinical studies. Ninety-eight of 183 students contacted (53.6%) completed a questionnaire comprising standard instruments measuring sleep quality (Pittsburgh Sleep Quality Index), daytime sleepiness (Epworth Sleepiness scale), and perceived stress (ten-item Perceived Stress Scale). Furthermore, we investigated coffee and energy drink consumption. Logistic regression was conducted to identify factors associated with poor sleep quality and the relation between sleep quality and academic performance (grade point average). High prevalences of poor sleep quality, excessive daytime sleepiness, and perceived stress were reported. In addition, higher odds of developing poor sleep quality were associated with coffee and energy drink intake, perceived stress, and excessive daytime sleepiness. The total Pittsburgh Sleep Quality Index score was inversely correlated with grade point average. First- and second-year podiatric medical students have poor sleep quality. Further research is needed to identify effective strategies to reduce stress and decrease coffee and energy drink intake to minimize their negative effect on sleep quality and academic performance in podiatric medical students.

Stress changes ahead of an advancing tunnel

USGS Publications Warehouse

Abel, J.F.; Lee, F.T.

1973-01-01

Instrumentation placed ahead of three model tunnels in the laboratory and ahead of a crosscut driven in a metamorphic rock mass detected stress changes several tunnel diameters ahead of the tunnel face. Stress changes were detected 4 diameters ahead of a model tunnel drilled into nearly elastic acrylic, 2??50 diameters ahead of a model tunnel drilled into concrete, and 2 diameters ahead of a model tunnel drilled into Silver Plume Granite. Stress changes were detected 7??50 diameters ahead of a crosscut driven in jointed, closely foliated gneisses and gneissic granites in an experimental mine at Idaho Springs, Colorado. These results contrast markedly with a theoretical elastic estimate of the onset of detectable stress changes at 1 tunnel diameter ahead of the tunnel face. A small compressive stress concentration was detected 2 diameters ahead of the model tunnel in acrylic, 1.25 diameters ahead of the model tunnel in concrete, and 1 diameter ahead of the model tunnel in granite. A similar stress peak was detected about 6 diameters ahead of the crosscut. No such stress peak is predicted from elastic theory. The 3-dimensional in situ stress determined in the field demonstrate that geologic structure controls stress orientations in the metamorphic rock mass. Two of the computed principal stresses are parallel to the foliation and the other principal stress is normal to it. The principal stress orientations vary approximately as the foliation attitude varies. The average horizontal stress components and the average vertical stress component are three times and twice as large, respectively, as those predicted from the overburden load. An understanding of the measured stress field appears to require the application of either tectonic or residual stress components, or both. Laboratory studies indicate the presence of proportionately large residual stresses. Mining may have triggered the release of strain energy, which is controlled by geologic structure. ?? 1973.

Application of the Shiono and Knight Method in asymmetric compound channels with different side slopes of the internal wall

NASA Astrophysics Data System (ADS)

Alawadi, Wisam; Al-Rekabi, Wisam S.; Al-Aboodi, Ali H.

2018-03-01

The Shiono and Knight Method (SKM) is widely used to predict the lateral distribution of depth-averaged velocity and boundary shear stress for flows in compound channels. Three calibrating coefficients need to be estimated for applying the SKM, namely eddy viscosity coefficient ( λ), friction factor ( f) and secondary flow coefficient ( k). There are several tested methods which can satisfactorily be used to estimate λ, f. However, the calibration of secondary flow coefficients k to account for secondary flow effects correctly is still problematic. In this paper, the calibration of secondary flow coefficients is established by employing two approaches to estimate correct values of k for simulating asymmetric compound channel with different side slopes of the internal wall. The first approach is based on Abril and Knight (2004) who suggest fixed values for main channel and floodplain regions. In the second approach, the equations developed by Devi and Khatua (2017) that relate the variation of the secondary flow coefficients with the relative depth ( β) and width ratio ( α) are used. The results indicate that the calibration method developed by Devi and Khatua (2017) is a better choice for calibrating the secondary flow coefficients than using the first approach which assumes a fixed value of k for different flow depths. The results also indicate that the boundary condition based on the shear force continuity can successfully be used for simulating rectangular compound channels, while the continuity of depth-averaged velocity and its gradient is accepted boundary condition in simulations of trapezoidal compound channels. However, the SKM performance for predicting the boundary shear stress over the shear layer region may not be improved by only imposing the suitable calibrated values of secondary flow coefficients. This is because difficulties of modelling the complex interaction that develops between the flows in the main channel and on the floodplain in this region.

Notch strength of composites

NASA Technical Reports Server (NTRS)

Whitney, J. M.

1983-01-01

The notch strength of composites is discussed. The point stress and average stress criteria relate the notched strength of a laminate to the average strength of a relatively long tensile coupon. Tests of notched specimens in which microstrain gages have been placed at or near the edges of the holes have measured strains much larger that those measured in an unnotched tensile coupon. Orthotropic stress concentration analyses of failed notched laminates have also indicated that failure occurred at strains much larger than those experienced on tensile coupons with normal gage lengths. This suggests that the high strains at the edge of a hole can be related to the very short length of fiber subjected to these strains. Lockheed has attempted to correlate a series of tests of several laminates with holes ranging from 0.19 to 0.50 in. Although the average stress criterion correlated well with test results for hole sizes equal to or greater than 0.50 in., it over-estimated the laminate strength in the range of hole sizes from 0.19 to 0.38 in. It thus appears that a theory is needed that is based on the mechanics of failure and is more generally applicable to the range of hole sizes and the varieties of laminates found in aircraft construction.

Surfactant Effect on the Average Flow Generation Near Curved Interface

NASA Astrophysics Data System (ADS)

Klimenko, Lyudmila; Lyubimov, Dmitry

2018-02-01

The present work is devoted to the average flow generation near curved interface with a surfactant adsorbed on the surface layer. The investigation was carried out for a liquid drop embedded in a viscous liquid with a different density. The liquid flows inside and outside the drop are generated by small amplitude and high frequency vibrations. Surfactant exchange between the drop surface and the surrounding liquid is limited by the process of adsorption-desorption. It was assumed that the surfactant is soluble in the surrounding liquid, but not soluble in the liquid drop. Surrounding liquid and the liquid in the drop are considered incompressible. Normal and shear viscous stresses balance at the interface is performed under the condition that the film thickness of the adsorbed surfactant is negligible. The problem is solved under assumption that the shape of the drop in the presence of adsorbed surfactant remains spherical symmetry. The effective boundary conditions for the tangential velocity jump and shear stress jump, describing the above generation have been obtained by matched asymptotic expansions method. The conditions under which the drop surface can be considered as a quasi-solid are determined. It is shown that in the case of the significant effect of surfactant on the surface tension, the dominant mechanism for the generation is the Schlichting mechanisms under vibrations.

Protection of Electrical Systems from EM Hazards - Design Guide.

DTIC Science & Technology

1981-09-01

cm) Surface flashover Voltage (KV/cm) This criterion should be met for lighting voltage stresses of either polarity applied at up to 1000 KV/v sec rate...suppressor devices can be predicted. The part failure rate models in the handbook include the effects of part electrical stress , thermal stress , operating... stress . This test series contained over one million device hours of operation at temperatures uF to 145°C. The average duration of testing ranges from

Histology and Biaxial Mechanical Behavior of Abdominal Aortic Aneurysm Tissue Samples.

PubMed

Pancheri, Francesco Q; Peattie, Robert A; Reddy, Nithin D; Ahamed, Touhid; Lin, Wenjian; Ouellette, Timothy D; Iafrati, Mark D; Luis Dorfmann, A

2017-03-01

Abdominal aortic aneurysms (AAAs) represent permanent, localized dilations of the abdominal aorta that can be life-threatening if progressing to rupture. Evaluation of risk of rupture depends on understanding the mechanical behavior of patient AAA walls. In this project, a series of patient AAA wall tissue samples have been evaluated through a combined anamnestic, mechanical, and histopathologic approach. Mechanical properties of the samples have been characterized using a novel, strain-controlled, planar biaxial testing protocol emulating the in vivo deformation of the aorta. Histologically, the tissue ultrastructure was highly disrupted. All samples showed pronounced mechanical stiffening with stretch and were notably anisotropic, with greater stiffness in the circumferential than the axial direction. However, there were significant intrapatient variations in wall stiffness and stress. In biaxial tests in which the longitudinal stretch was held constant at 1.1 as the circumferential stretch was extended to 1.1, the maximum average circumferential stress was 330 ± 70 kPa, while the maximum average axial stress was 190 ± 30 kPa. A constitutive model considering the wall as anisotropic with two preferred directions fit the measured data well. No statistically significant differences in tissue mechanical properties were found based on patient gender, age, maximum bulge diameter, height, weight, body mass index, or smoking history. Although a larger patient cohort is merited to confirm these conclusions, the project provides new insight into the relationships between patient natural history, histopathology, and mechanical behavior that may be useful in the development of accurate methods for rupture risk evaluation.

Bed material transport in the Virgin River, Utah

USGS Publications Warehouse

Andrews, E.D.

2000-01-01

Detailed information concerning the rate and particle size distribution of bed material transport by streamflows can be very difficult and expensive to obtain, especially where peak streamflows are brief and bed material is poorly sorted, including some very large boulders. Such streams, however, are common in steep, arid watersheds. Any computational approach must consider that (1) only the smaller particle sizes present on the streambed move even during large floods and (2) the largest bed particles exert a significant form drag on the flow. Conventional methods that rely on a single particle size to estimate the skin friction shear stress acting on the mobile fraction of the bed material perform poorly. Instead, for this study, the skin friction shear stress was calculated for the observed range of streamflows by calculating the form drag exerted on the reach‐averaged flow field by all particle sizes. Suspended and bed load transported rates computed from reach‐averaged skin friction shear stress are in excellent agreement with measured transport rates. The computed mean annual bed material load, including both bed load and suspended load, of the East Fork Virgin River for the water years 1992‐1996 was approximately 1.3×10 5 t. A large portion of the bed material load consists of sand‐sized particles, 0.062–1.0 mm in diameter, that are transported in suspension. Such particles, however, constituted only 10% of the surface bed material and less than 25% of the subsurface bed material. The mean annual quantity of bed load transported was 1060 t/yr with a median size of 15 mm.

Pubertal Stress and Nutrition and their Association with Sexual Orientation and Height in the Add Health Data

PubMed Central

Bogaert, Anthony F.

2018-01-01

A number of studies have indicated that gay men tend to be shorter, on average, than heterosexual men. Less evidence exists that lesbian women are taller, on average, than heterosexual women. The most popular explanation of the association between sexual orientation and height involves prenatal factors, such that, for example, gay men may have been exposed to lower than typical androgens during fetal development, which impacts their height and sexual orientation as adults. An alternative explanation involves stress, given that stress has been associated with sexual minority identification and with lower height. Another alternative explanation involves nutrition, although its relationship is less clear with sexual minority identification. Using the Add Health data, which is a large, nationally representative and longitudinal sample of American adolescents (n = 14,786), we tested a mediation model, such that sexual orientation → pubertal stress/nutrition → height. Within men, we found that gay men (n = 126) were shorter, on average, than heterosexual men (n = 6412). None of the 24 pubertal stress-related and 15 pubertal nutrition-related variables assessed in the Add Health data mediated the relationship between sexual orientation and height in men. Within women, lesbians (n = 75) did not differ significantly in stature compared to heterosexual women (n = 6267). Thus, prenatal mechanisms (e.g., hormones, maternal immune response) are likely better candidates for explaining the height difference between gay men and heterosexual men. PMID:27511207

Pubertal Stress and Nutrition and their Association with Sexual Orientation and Height in the Add Health Data.

PubMed

Skorska, Malvina N; Bogaert, Anthony F

2017-01-01

A number of studies have indicated that gay men tend to be shorter, on average, than heterosexual men. Less evidence exists that lesbian women are taller, on average, than heterosexual women. The most popular explanation of the association between sexual orientation and height involves prenatal factors, such that, for example, gay men may have been exposed to lower than typical androgens during fetal development, which impacts their height and sexual orientation as adults. An alternative explanation involves stress, given that stress has been associated with sexual minority identification and with lower height. Another alternative explanation involves nutrition, although its relationship is less clear with sexual minority identification. Using the Add Health data, which is a large, nationally representative and longitudinal sample of American adolescents (n = 14,786), we tested a mediation model, such that sexual orientation → pubertal stress/nutrition → height. Within men, we found that gay men (n = 126) were shorter, on average, than heterosexual men (n = 6412). None of the 24 pubertal stress-related and 15 pubertal nutrition-related variables assessed in the Add Health data mediated the relationship between sexual orientation and height in men. Within women, lesbians (n = 75) did not differ significantly in stature compared to heterosexual women (n = 6267). Thus, prenatal mechanisms (e.g., hormones, maternal immune response) are likely better candidates for explaining the height difference between gay men and heterosexual men.

Noise, stress, and annoyance in a pediatric intensive care unit.

PubMed

Morrison, Wynne E; Haas, Ellen C; Shaffner, Donald H; Garrett, Elizabeth S; Fackler, James C

2003-01-01

To measure and describe hospital noise and determine whether noise can be correlated with nursing stress measured by questionnaire, salivary amylase, and heart rate. Cohort observational study. Tertiary care center pediatric intensive care unit. Registered nurses working in the unit. None. Eleven nurse volunteers were recruited. An audiogram, questionnaire data, salivary amylase, and heart rate were collected in a quiet room. Each nurse was observed for a 3-hr period during patient care. Heart rate and sound level were recorded continuously; saliva samples and stress/annoyance ratings were collected every 30 mins. Variables assessed as potential confounders were years of nursing experience, caffeine intake, patients' Pediatric Risk of Mortality Score, shift assignment, and room assignment. Data were analyzed by random effects multiple linear regression using Stata 6.0. The average daytime sound level was 61 dB(A), nighttime 59 dB(A). Higher average sound levels significantly predicted higher heart rates (p =.014). Other significant predictors of tachycardia were higher caffeine intake, less nursing experience, and daytime shift. Ninety percent of the variability in heart rate was explained by the regression equation. Amylase measurements showed a large variability and were not significantly affected by noise levels. Higher average sound levels were also predictive of greater subjective stress (p =.021) and annoyance (p =.016). In this small study, noise was shown to correlate with several measures of stress including tachycardia and annoyance ratings. Further studies of interventions to reduce noise are essential.

Thermal deformations and stresses in composite materials

NASA Technical Reports Server (NTRS)

Daniel, I. M.

1980-01-01

Residual stresses are induced during curing in angle-ply laminates as a result of anisotropic thermal deformations of the variously oriented plies. Residual strains are measured experimentally using embedded strain gage techniques, and residual stresses are computed using orthotropic stress-strain relations. The results show that, for graphite and Kevlar laminates, residual stresses at room temperature are high enough to cause damage in the plies in the transverse to the fiber direction. It is also shown that residual stresses do not relax appreciably. The ply stacking sequence is found to have no effect on the magnitude of average residual stresses. Residual stresses and susceptibility to cracking during curing depend to a marked extent on ply layup.

Leisure education reduces stress among older adults.

PubMed

Chang, Liang-Chih

2014-01-01

The objectives of this study were to examine whether a leisure education program could facilitate leisure competence among older adults and whether it could also reduce their stress. A pre-test-post-test randomized experimental design was conducted. Subjects were randomly assigned to either an experimental group (n = 30) or a control group (n = 30). A leisure education program was used to serve as the intervention. A day before this experiment was carried out, pre-test data were collected using leisure competence and stress scales. Thirty minutes after this experiment ended, post-test data were collected using the same scales. These data were analyzed using an analysis of covariance. The results indicated that the average post-test scores of leisure competence in the experimental group were significantly higher than those in the control group and that the average post-test scores of stress in the experimental group were significantly lower than those in the control group. Healthcare practitioners should adopt the provision of leisure education as a priority to facilitate leisure competence and reduce stress among older adults.

Arthroscopic repair of chronic lateral ankle instability.

PubMed

Corte-Real, Nuno M; Moreira, Rodrigo M

2009-03-01

The current "gold standard'' for treatment of chronic lateral ankle instability is the Broström-Gould procedure. Most authors recommend this type of operation even after an arthroscopic inspection of the joint. We review our results with an arthroscopic method of lateral ankle ligament repair. A method of arthroscopic lateral ligament repair with an anchor placed in the fibula is described. We used this technique on 31 consecutive patients (28 were available for followup). Twenty-one patients had work or traffic accidents, four suffered casual falls. and three had sport-related lesions. The patients were evaluated after 24.5 month average followup. The average postoperative AOFAS score was 85.3 (82.3 in the workers-compensation group and 94.4 in the others) and average satisfaction was 3.8 (3.5 to workers-compensation and 4.6 for the others). Complications occurred in nine patients (29%), but only three cases had ongoing problems. We had two recurrences (another sprain without instability on the stress radiograph). Three patients had some wound healing problems and three had injuries of the superficial peroneal nerve, one of which is persistent. One patient developed a deep venous thrombosis postoperatively. With this method, we achieved good clinical results. We had several complications but most of them were minor. It was a simple procedure with less morbidity to most patients. We believe it produced an anatomical repair of the lateral ligament with clinical and functional results similar to other techniques.

Timing of Favorable Conditions, Competition and Fertility Interact to Govern Recruitment of Invasive Chinese Tallow Tree in Stressful Environments

PubMed Central

Gabler, Christopher A.; Siemann, Evan

2013-01-01

The rate of new exotic recruitment following removal of adult invaders (reinvasion pressure) influences restoration outcomes and costs but is highly variable and poorly understood. We hypothesize that broad variation in average reinvasion pressure of Triadica sebifera (Chinese tallow tree, a major invader) arises from differences among habitats in spatiotemporal availability of realized recruitment windows. These windows are periods of variable duration long enough to permit establishment given local environmental conditions. We tested this hypothesis via a greenhouse mesocosm experiment that quantified how the duration of favorable moisture conditions prior to flood or drought stress (window duration), competition and nutrient availability influenced Triadica success in high stress environments. Window duration influenced pre-stress seedling abundance and size, growth during stress and final abundance; it interacted with other factors to affect final biomass and germination during stress. Stress type and competition impacted final size and biomass, plus germination, mortality and changes in size during stress. Final abundance also depended on competition and the interaction of window duration, stress type and competition. Fertilization interacted with competition and stress to influence biomass and changes in height, respectively, but did not affect Triadica abundance. Overall, longer window durations promoted Triadica establishment, competition and drought (relative to flood) suppressed establishment, and fertilization had weak effects. Interactions among factors frequently produced different effects in specific contexts. Results support our ‘outgrow the stress’ hypothesis and show that temporal availability of abiotic windows and factors that influence growth rates govern Triadica recruitment in stressful environments. These findings suggest that native seed addition can effectively suppress superior competitors in stressful environments. We also describe environmental scenarios where specific management methods may be more or less effective. Our results enable better niche-based estimates of local reinvasion pressure, which can improve restoration efficacy and efficiency by informing site selection and optimal management. PMID:23967212

Male lifespan and the secondary sex ratio.

PubMed

Catalano, Ralph; Bruckner, Tim

2006-01-01

Literature speculating on the fetal origins of later life morbidity often invokes the "damaged cohort" theory, i.e., that maternal responses to exogenous shocks induce "stress reactivity" in fetuses and thereby shorten the lifespan of males in utero during stressful times. A rival, or "culled cohort," theory posits that exogenous shocks to gravid females induce spontaneous abortions of frail male fetuses, leaving relatively hardy survivors who enjoy, on average, lifespans longer than males in less stressed birth cohorts. A recent test based on archival data from Sweden supported the culled cohort theory. Several characteristics of the Swedish data, however, raise questions regarding the external validity of the findings. We repeat the test with data from Denmark, Iceland, and England and Wales. We use time-series methods that control for trends, seasonal cycles, and other forms of autocorrelation that could confound the test. None of the results supports the "damaged cohort" theory. Consistent with the Swedish findings and with evolutionary theory, we find support in Iceland and England and Wales for the "culled cohort" theory. We discuss the implications of our findings for basic research as well as for public health.

New concept for treating female stress urinary incontinence with radiofrequency.

PubMed

Lordelo, Patrícia; Vilas Boas, Andrea; Sodré, Danielle; Lemos, Amanda; Tozetto, Sibele; Brasil, Cristina

2017-01-01

To evaluate the clinical response and adverse effects of radiofrequency on the urethral meatus in the treatment of stress urinary incontinence in women. This phase one study included ten women with Stress Urinary Incontinence (SUI). The evaluation consisted of 1 hour Pad tests to quantify urine loss and to assess the degree of procedure satisfaction by using the Likert scale. To evaluate safety, we observed the number of referred side effects. Average age was 53.10 years±7.08 years. In assessing the final Pad Test, 70% showed a reduction and 30% a worsening of urinary loss. Using the Pad Test one month later, there was a reduction in all patients (p=0.028). The degree of satisfaction was 90% and no side effects have been observed. One patient reported burning sensation. The treatment of SUI with radiofrequency on the urethral meatus has no adverse effects, being a low risk method that reduces urinary loss in women. However, to increase the validity of the study, larger clinical trials are warranted. Copyright® by the International Brazilian Journal of Urology.

The Role and Modeling of Dispersive Stresses

NASA Astrophysics Data System (ADS)

Shavit, U.; Moltchanov, S.

2012-12-01

Dispersive stresses represent momentum fluxes that are induced by the spatial heterogeneity of flow environments such as forest canopies, river vegetation and coral reefs. When deriving the average momentum equation for such flow environments, these dispersive stresses resemble the Reynolds stresses but instead of correlations of temporal fluctuations they represent correlations of spatial fluctuations. Surprisingly, these stresses are ignored in flow models and very few studies attempted to provide a physical interpretation, let alone a closure model. Typical arguments that justify such modeling are that these stresses are small and negligible; however, recent studies have shown that they may be important. In a recent study we showed that dispersive stresses at the inlet to obstructed region (made of glass cylinders) are larger than the Reynolds stresses and their contribution to the momentum balance is as important as the pressure and the drag forces. In this presentation we will try to explain what they are, provide some intuitive physical interoperation and show that closure models can be developed. Our results are based on highly detailed particle image velocimeter (PIV) measurements that were obtained inside a canopy model made of vertical thin glass plates. Forty nine vertical cross sections were obtained 1000 times generating a huge dataset of more than 250 million data points for each flow conditions. A careful spatial averaging procedure was developed and both temporal and spatial correlations were obtained. An order of magnitude analysis will be presented and the role of each of the terms in the momentum equation will be evaluated. It will be shown that the dispersive stresses are large and significant within the area of the canopy leading edge. Since dispersive stresses do not exist upstream from the canopy they are expected to grow once the flow enters the canopy. Our PIV data shows an initial fast growth up to about one length scale into the patch. Following this peak value the dispersive stresses decrease, reaching low and constant values further downstream. The actual distance of importance depends on the drag imposed by the canopy. The challenging task of studying dispersive stresses is the development of closure models. We will demonstrate a linear relationship between the normal dispersive stresses and the square of the double-average velocity. We will also show that the non-constant proportionality coefficient depends on the area of the wakes behind the obstacles. We will propose a simple formulation for this coefficient and will use our detailed PIV measurements to demonstrate the good agreement between the modeled and measured stresses, both at the entry region and in the fully-developed region.

FEM Modeling of In-Plane Stress Distribution in Thick Brittle Coatings/Films on Ductile Substrates Subjected to Tensile Stress to Determine Interfacial Strength.

PubMed

Wang, Kaishi; Zhang, Fangzhou; Bordia, Rajendra K

2018-03-27

The ceramic-metal interface is present in various material structures and devices that are vulnerable to failures, like cracking, which are typically due to their incompatible properties, e.g., thermal expansion mismatch. In failure of these multilayer systems, interfacial shear strength is a good measure of the robustness of interfaces, especially for planar films. There is a widely-used shear lag model and method by Agrawal and Raj to analyse and measure the interfacial shear strength of thin brittle film on ductile substrates. The use of this classical model for a type of polymer derived ceramic coatings (thickness ~18 μm) on steel substrate leads to high values of interfacial shear strength. Here, we present finite element simulations for such a coating system when it is subjected to in-plane tension. Results show that the in-plane stresses in the coating are non-uniform, i.e., varying across the thickness of the film. Therefore, they do not meet one of the basic assumptions of the classical model: uniform in-plane stress. Furthermore, effects of three significant parameters, film thickness, crack spacing, and Young's modulus, on the in-plane stress distribution have also been investigated. 'Thickness-averaged In-plane Stress' (TIS), a new failure criterion, is proposed for estimating the interfacial shear strength, which leads to a more realistic estimation of the tensile strength and interfacial shear strength of thick brittle films/coatings on ductile substrates.

Fully solution processed PEDOT:PSS and silver nanowire semitransparent electrodes for thin film solar cells

NASA Astrophysics Data System (ADS)

Vaagensmith, Bjorn

Building integrated photovoltaics (BIPV), such as semitransparent organic solar cells (OSC) for power generating windows, is a promising method for implementing renewable energy under the looming threat of depleting fossil fuels. OSC require a solution processed transparent electrode to be cost effective; but typically employ a non-solution processed indium tin oxide (ITO) transparent electrode. PEDOT:PSS and silver nanowire transparent electrodes have emerged as a promising alternative to ITO and are solution processed compatible. However, PEDOT:PSS requires a strong acid treatment, which is incompatible with high throughput solution processed fabrication techniques. Silver nanowires suffer from a short lifetime when subject to electrical stress. The goals of this work were to fabricate a PEDOT:PSS electrodes without using strong acids, a silver nanowire electrode with a lifetime that can exceed 6000 hours of constant electrical stress, and use these two electrodes to fabricate a semitransparent OSC. Exploring optimal solvent blend additives in conjunction with solvent bend post treatments for PEDOT:PSS electrodes could provide an acid free method that results in comparable sheet resistance and transmittance of ITO electrodes. Silver nanowires fail under electrical stress due to sulfur corrosion and Joule heating (which melts and breaks apart electrical contact). A silver oxide layer coating the nanowires could hinder sulfur corrosion and help redistribute heat. Moreover, nanowires with thicker diameters could also exhibit higher heat tolerance and take longer to corrode. Four layer PEDOT:PSS electrodes with optimal solvent blend additives and post treatments were fabricated by spin coating. Silver nanowire electrodes of varying nanowire diameter with and without UV-ozone treatment were fabricated by spray coating and subject to electrical stress of 20 mA/cm2 constant current density. PEDOT:PSS electrodes exhibited a sheet resistance of 80 O/□ and average transmittance of 73%, which were too high and too low, respectively. Silver nanowire electrodes, on the other hand, were able to achieve sheet resistances below 50 O/□ while maintaining a direct transmittance above 80%. Silver nanowires electrodes with average nanowire diameters of 80 nm lasted 2 days longer with UV-ozone treatment than without; and silver nanowire electrodes with average nanowire diameters of 233 nm lasted for 6,312 hours, which met the 6000 hour goal. PEDOT:PSS transparent electrode needs to be improved where the sheet resistance is below 50 O/□ and transmittance above 80%. This could be achieved by adding silver nanoparticles (SNP) less than 40 nm in size, which would also have a plasmonic effect enabling the solar cell to absorb ultraviolet light. Then a fully solution processed semitransparent solar cell utilizing a PEDOT:PSS:SNP and silver nanowire transparent electrodes can be fabricated.

Simulation of surface hardening in the deep rolling process by means of an axial symmetric nodal averaged finite element

NASA Astrophysics Data System (ADS)

Morrev, P. G.; Gordon, V. A.

2018-03-01

Surface hardening by deep rolling can be considered as the axial symmetric problem in some special events (namely, when large R and small r radii of the deforming roller meet the requirement R>> r). An axisymmetric nodal averaged stabilized finite element is formulated. The formulation is based on a variational principle with a penalty (stabilizing) item in order to involve large elastic-plastic strain and near to incompressible materials. The deep rolling process for a steel rod is analyzed. Axial residual stress, yield stress, and Odkvist’s parameter are calculated. The residual stress is compared with the data obtained by other authors using a three-dimensional statement of the problem. The results obtained demonstrate essential advantages of the newly developed finite element.

A phoenics model for the triaxial loading of an initially cylindrical mass of rate-type material with provisions for bulging and yield

NASA Technical Reports Server (NTRS)

French, K. W., Jr.

1986-01-01

This work traces the response of a granular material via the Ten Coefficient Truesdell rate-type constituitive model into the simplest meaningful loading: the triaxial test configuration. A functional relation has been posed for computing the rather peculiar relation between average applied stress and average porosity. Using that relation an attack has been mounted on the dilemma that exists between dynamic and constitutive use of the pressure variable; that is relating dynamic pressure, thermodynamic pressure, stress deviator and higher stress invariants. The resolution was as a linear superposition with a one-way feedback, in that while the dynamic component could not effect the constituitive component, the converse was not true since density appears in the momentum transport relation.

Rock Fracture Toughness Under Mode II Loading: A Theoretical Model Based on Local Strain Energy Density

NASA Astrophysics Data System (ADS)

Rashidi Moghaddam, M.; Ayatollahi, M. R.; Berto, F.

2018-01-01

The values of mode II fracture toughness reported in the literature for several rocks are studied theoretically by using a modified criterion based on strain energy density averaged over a control volume around the crack tip. The modified criterion takes into account the effect of T-stress in addition to the singular terms of stresses/strains. The experimental results are related to mode II fracture tests performed on the semicircular bend and Brazilian disk specimens. There are good agreements between theoretical predictions using the generalized averaged strain energy density criterion and the experimental results. The theoretical results reveal that the value of mode II fracture toughness is affected by the size of control volume around the crack tip and also the magnitude and sign of T-stress.

A New and General Formulation of the Parametric HFGMC Micromechanical Method for Three-Dimensional Multi-Phase Composites

NASA Technical Reports Server (NTRS)

Haj-Ali, Rami; Aboudi, Jacob

2012-01-01

The recent two-dimensional (2-D) parametric formulation of the high fidelity generalized method of cells (HFGMC) reported by the authors is generalized for the micromechanical analysis of three-dimensional (3-D) multiphase composites with periodic microstructure. Arbitrary hexahedral subcell geometry is developed to discretize a triply periodic repeating unit-cell (RUC). Linear parametric-geometric mapping is employed to transform the arbitrary hexahedral subcell shapes from the physical space to an auxiliary orthogonal shape, where a complete quadratic displacement expansion is performed. Previously in the 2-D case, additional three equations are needed in the form of average moments of equilibrium as a result of the inclusion of the bilinear terms. However, the present 3-D parametric HFGMC formulation eliminates the need for such additional equations. This is achieved by expressing the coefficients of the full quadratic polynomial expansion of the subcell in terms of the side or face average-displacement vectors. The 2-D parametric and orthogonal HFGMC are special cases of the present 3-D formulation. The continuity of displacements and tractions, as well as the equilibrium equations, are imposed in the average (integral) sense as in the original HFGMC formulation. Each of the six sides (faces) of a subcell has an independent average displacement micro-variable vector which forms an energy-conjugate pair with the transformed average-traction vector. This allows generating symmetric stiffness matrices along with internal resisting vectors for the subcells which enhances the computational efficiency. The established new parametric 3-D HFGMC equations are formulated and solution implementations are addressed. Several applications for triply periodic 3-D composites are presented to demonstrate the general capability and varsity of the present parametric HFGMC method for refined micromechanical analysis by generating the spatial distributions of local stress fields. These applications include triply periodic composites with inclusions in the form of a cavity, spherical inclusion, ellipsoidal inclusion, discontinuous aligned short fiber. A 3-D repeating unit-cell for foam material composite is simulated.

Preliminary investigation of steel girder end panel shear resistance.

DOT National Transportation Integrated Search

2010-01-01

Prior to 1973, steel bridges in California were designed based on Allowable Stress : Design and the shear design of web and transverse stiffeners was based on the : average shear stress in the web. The tension field action equation similar to the : c...

Managing Stress in the Principalship.

ERIC Educational Resources Information Center

Lyons, James E.

1990-01-01

The principal's office is frequently a collection point for problems and demands. Secondary school principals often average 1,000 interactions daily. Principals can manage stress by declining to solve every problem, delegating responsibility, reexamining their supervisory role, developing networks of trusted friends, and engaging in…

How Health Behaviors Relate to Academic Performance via Affect: An Intensive Longitudinal Study

PubMed Central

Flueckiger, Lavinia; Lieb, Roselind; Meyer, Andrea H.; Mata, Jutta

2014-01-01

Objective This intensive longitudinal study examined how sleep and physical activity relate to university students’ affect and academic performance during a stressful examination period. Methods On 32 consecutive days, 72 first-year students answered online questionnaires on their sleep quality, physical activity, positive and negative affect, learning goal achievement, and examination grades. First-year university students are particularly well-suited to test our hypotheses: They represent a relatively homogeneous population in a natural, but controlled setting, and simultaneously deal with similar stressors, such as examinations. Data were analyzed using multilevel structural equation models. Results Over the examination period, better average sleep quality but not physical activity predicted better learning goal achievement. Better learning goal achievement was associated with increased probability of passing all examinations. Relations of average sleep quality and average physical activity with learning goal achievement were mediated by experienced positive affect. In terms of day-to-day dynamics, on days with better sleep quality, participants reported better learning goal achievement. Day-to-day physical activity was not related to daily learning goal achievement. Daily positive and negative affect both mediated the effect of day-to-day sleep quality and physical activity on daily learning goal achievement. Conclusion Health behaviors such as sleep quality and physical activity seem important for both academic performance and affect experience, an indicator of mental health, during a stressful examination period. These results are a first step toward a better understanding of between- and within-person variations in health behaviors, affect, and academic performance, and could inform prevention and intervention programs for university students. PMID:25353638

Distinguishing body mass and activity level from the lower limb: can entheses diagnose obesity?

PubMed

Godde, Kanya; Taylor, Rebecca Wilson

2013-03-10

The ability to estimate body size from the skeleton has broad applications, but is especially important to the forensic community when identifying unknown skeletal remains. This research investigates the utility of using entheses/muscle skeletal markers of the lower limb to estimate body size and to classify individuals into average, obese, and active categories, while using a biomechanical approach to interpret the results. Eighteen muscle attachment sites of the lower limb, known to be involved in the sit-to-stand transition, were scored for robusticity and stress in 105 white males (aged 31-81 years) from the William M. Bass Donated Skeletal Collection. Both logistic regression and log linear models were applied to the data to (1) test the utility of entheses as an indicator of body weight and activity level, and (2) to generate classification percentages that speak to the accuracy of the method. Thirteen robusticity scores differed significantly between the groups, but classification percentages were only slightly greater than chance. However, clear differences could be seen between the average and obese and the average and active groups. Stress scores showed no value in discriminating between groups. These results were interpreted in relation to biomechanical forces at the microscopic and macroscopic levels. Even though robusticity alone is not able to classify individuals well, its significance may show greater value when incorporated into a model that has multiple skeletal indicators. Further research needs to evaluate a larger sample and incorporate several lines of evidence to improve classification rates. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

Modular Hamiltonians for deformed half-spaces and the averaged null energy condition

DOE PAGES

Faulkner, Thomas; Leigh, Robert G.; Parrikar, Onkar; ...

2016-09-08

We study modular Hamiltonians corresponding to the vacuum state for deformed half-spaces in relativistic quantum field theories on R 1,d-1. We show that in addition to the usual boost generator, there is a contribution to the modular Hamiltonian at first order in the shape deformation, proportional to the integral of the null components of the stress tensor along the Rindler horizon. We use this fact along with monotonicity of relative entropy to prove the averaged null energy condition in Minkowski space-time. This subsequently gives a new proof of the Hofman-Maldacena bounds on the parameters appearing in CFT three-point functions. Ourmore » main technical advance involves adapting newly developed perturbative methods for calculating entanglement entropy to the problem at hand. Our methods were recently used to prove certain results on the shape dependence of entanglement in CFTs and here we generalize these results to excited states and real time dynamics. Finally, we discuss the AdS/CFT counterpart of this result, making connection with the recently proposed gravitational dual for modular Hamiltonians in holographic theories.« less

Modular Hamiltonians for deformed half-spaces and the averaged null energy condition

NASA Astrophysics Data System (ADS)

Faulkner, Thomas; Leigh, Robert G.; Parrikar, Onkar; Wang, Huajia

2016-09-01

We study modular Hamiltonians corresponding to the vacuum state for deformed half-spaces in relativistic quantum field theories on {{R}}^{1,d-1} . We show that in addition to the usual boost generator, there is a contribution to the modular Hamiltonian at first order in the shape deformation, proportional to the integral of the null components of the stress tensor along the Rindler horizon. We use this fact along with monotonicity of relative entropy to prove the averaged null energy condition in Minkowski space-time. This subsequently gives a new proof of the Hofman-Maldacena bounds on the parameters appearing in CFT three-point functions. Our main technical advance involves adapting newly developed perturbative methods for calculating entanglement entropy to the problem at hand. These methods were recently used to prove certain results on the shape dependence of entanglement in CFTs and here we generalize these results to excited states and real time dynamics. We also discuss the AdS/CFT counterpart of this result, making connection with the recently proposed gravitational dual for modular Hamiltonians in holographic theories.

Modular Hamiltonians for deformed half-spaces and the averaged null energy condition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Faulkner, Thomas; Leigh, Robert G.; Parrikar, Onkar

We study modular Hamiltonians corresponding to the vacuum state for deformed half-spaces in relativistic quantum field theories on R 1,d-1. We show that in addition to the usual boost generator, there is a contribution to the modular Hamiltonian at first order in the shape deformation, proportional to the integral of the null components of the stress tensor along the Rindler horizon. We use this fact along with monotonicity of relative entropy to prove the averaged null energy condition in Minkowski space-time. This subsequently gives a new proof of the Hofman-Maldacena bounds on the parameters appearing in CFT three-point functions. Ourmore » main technical advance involves adapting newly developed perturbative methods for calculating entanglement entropy to the problem at hand. Our methods were recently used to prove certain results on the shape dependence of entanglement in CFTs and here we generalize these results to excited states and real time dynamics. Finally, we discuss the AdS/CFT counterpart of this result, making connection with the recently proposed gravitational dual for modular Hamiltonians in holographic theories.« less

Ex-Vivo Lymphatic Perfusion System for Independently Controlling Pressure Gradient and Transmural Pressure in Isolated Vessels

PubMed Central

Kornuta, Jeffrey A.; Dixon, J. Brandon

2015-01-01

In addition to external forces, collecting lymphatic vessels intrinsically contract to transport lymph from the extremities to the venous circulation. As a result, the lymphatic endothelium is routinely exposed to a wide range of dynamic mechanical forces, primarily fluid shear stress and circumferential stress, which have both been shown to affect lymphatic pumping activity. Although various ex-vivo perfusion systems exist to study this innate pumping activity in response to mechanical stimuli, none are capable of independently controlling the two primary mechanical forces affecting lymphatic contractility: transaxial pressure gradient, ΔP, which governs fluid shear stress; and average transmural pressure, Pavg, which governs circumferential stress. Hence, the authors describe a novel ex-vivo lymphatic perfusion system (ELPS) capable of independently controlling these two outputs using a linear, explicit model predictive control (MPC) algorithm. The ELPS is capable of reproducing arbitrary waveforms within the frequency range observed in the lymphatics in vivo, including a time-varying ΔP with a constant Pavg, time-varying ΔP and Pavg, and a constant ΔP with a time-varying Pavg. In addition, due to its implementation of syringes to actuate the working fluid, a post-hoc method of estimating both the flow rate through the vessel and fluid wall shear stress over multiple, long (5 sec) time windows is also described. PMID:24809724

[A study of the occupational stress norm and it' s application for the technical group and scientific research group].

PubMed

Yang, Xin-wei; Liu, Ze-jun; Zhao, Pei-qing; Bai, Shao-ying; Pang, Xing-huo; Wang, Zhi-ming; Jin, Tai-yi; Lan, Ya-jia

2006-11-01

A study of the occupational stress norm and it' s application for the technical group and scientific research group. In this study, cross-sectional study method is used, and a synthetic way of sorting and randomized sampling is adopted to deal with research targets(235 scientific research group, 857 technical group). Descriptive statistics for OSI-R scale scores for the technical group and scientific research group were modulated. Scale raw score to T-score conversion tables derived from the OSI-R normative sample for technical group and scientific research group were established. OSI-R profile from for technical group and scientific research group were established. For the ORQ and PSQ scales, scores at or above 70T indicate a strong levels of maladaptive stress and strain. Score in the range of 60T to 69T suggest middle levels of maladaptive stress and strain. Score in the range of 40T to 59T indicate normal levels of stress and strain. Score below 40T indicate a relative absence of occupational stress and strain. For the PRQ scales, score below 30T indicate a significant lack of coping resources. Score in the range of 30T to 39T suggest middle deficits in coping resources. Score in the range of 40T to 59T indicate average coping resources. Scores at or above 60T indicate a strong levels of coping resources. Different intervention measure should be take to reduce the occupational stress so as to improve the work ability.

Compensation for use of monthly-averaged winds in numerical modeling

NASA Technical Reports Server (NTRS)

Parkinson, C. L.

1981-01-01

Ratios R of the monthly averaged wind speeds to the magnitudes of the monthly averaged wind vectors are presented over a 41 x 41 grid covering the southern Ocean and the Antarctic continent. The ratio is found to vary from 1 to over 1000, with an average value of 1.86. These ratios R are relevant for converting from sensible and latent heats calculated with mean monthly data to those calculated with 12 hourly data. The corresponding ratios alpha for wind stress, along with the angle deviations involved, are also presented over the same 41 x 41 grid. The values of alpha generally exceed those for R and average 2.66. Regions in zones of variable wind directions have larger R and alpha ratios, over the ice-covered portions of the southern Ocean averaging 2.74 and 4.35 for R and alpha respectively. Thus adjustments to compensate for the use of mean monthly wind velocities should be stronger for wind stress than for turbulent heats and stronger over ice covered regions than over regions with more persistent wind directions, e.g., those in the belt of mid-latitude westerlies.

Correcting the Relative Bias of Light Obscuration and Flow Imaging Particle Counters.

PubMed

Ripple, Dean C; Hu, Zhishang

2016-03-01

Industry and regulatory bodies desire more accurate methods for counting and characterizing particles. Measurements of proteinaceous-particle concentrations by light obscuration and flow imaging can differ by factors of ten or more. We propose methods to correct the diameters reported by light obscuration and flow imaging instruments. For light obscuration, diameters were rescaled based on characterization of the refractive index of typical particles and a light scattering model for the extinction efficiency factor. The light obscuration models are applicable for either homogeneous materials (e.g., silicone oil) or for chemically homogeneous, but spatially non-uniform aggregates (e.g., protein aggregates). For flow imaging, the method relied on calibration of the instrument with silica beads suspended in water-glycerol mixtures. These methods were applied to a silicone-oil droplet suspension and four particle suspensions containing particles produced from heat stressed and agitated human serum albumin, agitated polyclonal immunoglobulin, and abraded ethylene tetrafluoroethylene polymer. All suspensions were measured by two flow imaging and one light obscuration apparatus. Prior to correction, results from the three instruments disagreed by a factor ranging from 3.1 to 48 in particle concentration over the size range from 2 to 20 μm. Bias corrections reduced the disagreement from an average factor of 14 down to an average factor of 1.5. The methods presented show promise in reducing the relative bias between light obscuration and flow imaging.

Intermediate Temperature Stress Rupture of a Woven Hi-Nicalon, BN-Interphase, SiC Matric Composite in Air

NASA Technical Reports Server (NTRS)

Morscher, Gregory N.; Hurst, Janet; Brewer, David

1999-01-01

Woven Hi-Nicalon (TM) reinforced melt-infiltrated SiC matrix composites were tested under tensile stress-rupture conditions in air at intermediate temperatures. A comprehensive examination of the damage state and the fiber properties at failure was performed. Modal acoustic emission analysis was used to monitor damage during the experiment. Extensive microscopy of the composite fracture surfaces and the individual fiber fracture surfaces was used to determine the mechanisms leading to ultimate failure. The rupture properties of these composites were significantly worse than expected compared to the fiber properties under similar conditions. This was due to the oxidation of the BN interphase. Oxidation occurred through the matrix cracks that intersected the surface or edge of a tensile bar. These oxidation reactions resulted in minor degradation to fiber strength and strong bonding of the fibers to one another at regions of near fiber-to-fiber contact. It was found that two regimes for rupture exist for this material: a high stress regime where rupture occurs at a fast rate and a low stress regime where rupture occurs at a slower rate. For the high stress regime, the matrix damage state consisted of through thickness cracks. The average fracture strength of fibers that were pulled-out (the final fibers to break before ultimate failure) was controlled by the slow-crack growth rupture criterion in the literature for individual Hi-Nicalon (TM) fibers. For the low stress regime, the matrix damage state consisted of microcracks which grew during the rupture test. The average fracture strength of fibers that were pulled-out in this regime was the same as the average fracture strength of individual fibers pulled out in as-produced composites tested at room temperature.

Perceptions of Healthy Eating and Influences on the Food Choices of Appalachian Youth

PubMed Central

Swanson, Mark; Schoenberg, Nancy E.; Davis, Rian; Wright, Sherry; Dollarhide, Kaye

2011-01-01

Objective Patterns of overweight and obesity are unequally distributed geographically, with elevated rates in Appalachia. Appalachian youth's perceptions toward healthy eating and influences on food choice were examined as part of formative research to address these disparities. Methods Eleven focus groups, averaging 6 youth (n=68) and moderated by experienced local residents, were conducted with participants aged 8–17. Session transcripts were coded for thematic analysis, using measures to enhance rigor and transferability. Results Participants discussed numerous internal and external factors affecting dietary choices. While expressing confidence in their own nutritional knowledge, they stressed the importance of taste preferences, cost, convenience, social influences, and advertising on diet. Conclusions and Implications Appalachian youths' awareness of the multiple influences on diet may create opportunities for multi-faceted, ecologically-based interventions. In particular, participants stressed the importance of social influences on diet and on successful nutrition programming. PMID:22269474

Study on constant-step stress accelerated life tests in white organic light-emitting diodes.

PubMed

Zhang, J P; Liu, C; Chen, X; Cheng, G L; Zhou, A X

2014-11-01

In order to obtain reliability information for a white organic light-emitting diode (OLED), two constant and one step stress tests were conducted with its working current increased. The Weibull function was applied to describe the OLED life distribution, and the maximum likelihood estimation (MLE) and its iterative flow chart were used to calculate shape and scale parameters. Furthermore, the accelerated life equation was determined using the least squares method, a Kolmogorov-Smirnov test was performed to assess if the white OLED life follows a Weibull distribution, and self-developed software was used to predict the average and the median lifetimes of the OLED. The numerical results indicate that white OLED life conforms to a Weibull distribution, and that the accelerated life equation completely satisfies the inverse power law. The estimated life of a white OLED may provide significant guidelines for its manufacturers and customers. Copyright © 2014 John Wiley & Sons, Ltd.

Frictional sliding inclusions

NASA Astrophysics Data System (ADS)

Huang, Jin H.; Furuhashi, R.; Mura, T.

1993-02-01

S OLUTIONS ARE presented in closed form by using an averaging method for inclusions sliding along an interface due to uniform eigenstrains precribed in the inclusions. The associated stress fields are also analytically determined. A parameter s is introduced to indicate the relative magnitude of sliding compared with the extreme cases of perfect bonding and perfect sliding. When the parameter s becomes zero, the present solution coincides with Eshelby's solution which is the perfectly bonded case. In contrast, when the parameter s is unity, the solution agrees with Volterra's solution (M URA and F URUHASHI, 1984, J. appl. Mech.51, 308] for the perfect sliding case. Because of non-uniform elastic fields caused by sliding along the interface, the well-known Eshelby tensor is modified for the sliding inclusions. Moreover, based on the Mori-Tanaka theory (M ORI and T ANAKA, 1973, Acta Metall.21, 571), an overall stress-strain relation is established to characterize the sliding effect on the overall elastic moduli.

Durability evaluation of ceramic components using CARES/LIFE

NASA Technical Reports Server (NTRS)

Nemeth, Noel N.; Powers, Lynn M.; Janosik, Lesley A.; Gyekenyesi, John P.

1994-01-01

The computer program CARES/LIFE calculates the time-dependent reliability of monolithic ceramic components subjected to thermomechanical and/or proof test loading. This program is an extension of the CARES (Ceramics Analysis and Reliability Evaluation of Structures) computer program. CARES/LIFE accounts for the phenomenon of subcritical crack growth (SCG) by utilizing the power law, Paris law, or Walker equation. The two-parameter Weibull cumulative distribution function is used to characterize the variation in component strength. The effects of multiaxial stresses are modeled using either the principle of independent action (PIA), the Weibull normal stress averaging method (NSA), or the Batdorf theory. Inert strength and fatigue parameters are estimated from rupture strength data of naturally flawed specimens loaded in static, dynamic, or cyclic fatigue. Application of this design methodology is demonstrated using experimental data from alumina bar and disk flexure specimens which exhibit SCG when exposed to water.

Durability evaluation of ceramic components using CARES/LIFE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nemeth, N.N.; Janosik, L.A.; Gyekenyesi, J.P.

1996-01-01

The computer program CARES/LIFE calculates the time-dependent reliability of monolithic ceramic components subjected to thermomechanical and/or proof test loading. This program is an extension of the CARES (Ceramics Analysis and Reliability Evaluation of Structures) computer program. CARES/LIFE accounts for the phenomenon of subcritical crack growth (SCG) by utilizing the power law, Paris law, or Walker equation. The two-parameter Weibull cumulative distribution function is used to characterize the variation in component strength. The effects of multiaxial stresses are modeled using either the principle of independent action (PIA), the Weibull normal stress averaging method (NSA), or the Batdorf theory. Inert strength andmore » fatigue parameters are estimated from rupture strength data of naturally flawed specimens loaded in static, dynamic, or cyclic fatigue. Application of this design methodology is demonstrated using experimental data from alumina bar and disk flexure specimens, which exhibit SCG when exposed to water.« less

Lifetime Reliability Evaluation of Structural Ceramic Parts with the CARES/LIFE Computer Program

NASA Technical Reports Server (NTRS)

Nemeth, Noel N.; Powers, Lynn M.; Janosik, Lesley A.; Gyekenyesi, John P.

1993-01-01

The computer program CARES/LIFE calculates the time-dependent reliability of monolithic ceramic components subjected to thermomechanical and/or proof test loading. This program is an extension of the CARES (Ceramics Analysis and Reliability Evaluation of Structures) computer program. CARES/LIFE accounts for the phenomenon of subcritical crack growth (SCG) by utilizing the power law, Paris law, or Walker equation. The two-parameter Weibull cumulative distribution function is used to characterize the variation in component strength. The effects of multiaxial stresses are modeled using either the principle of independent action (PIA), Weibull's normal stress averaging method (NSA), or Batdorf's theory. Inert strength and fatigue parameters are estimated from rupture strength data of naturally flawed specimens loaded in static, dynamic, or cyclic fatigue. Two example problems demonstrating cyclic fatigue parameter estimation and component reliability analysis with proof testing are included.

Applications of Analytical Self-Similar Solutions of Reynolds-Averaged Models for Instability-Induced Turbulent Mixing

NASA Astrophysics Data System (ADS)

Hartland, Tucker; Schilling, Oleg

2017-11-01

Analytical self-similar solutions to several families of single- and two-scale, eddy viscosity and Reynolds stress turbulence models are presented for Rayleigh-Taylor, Richtmyer-Meshkov, and Kelvin-Helmholtz instability-induced turbulent mixing. The use of algebraic relationships between model coefficients and physical observables (e.g., experimental growth rates) following from the self-similar solutions to calibrate a member of a given family of turbulence models is shown. It is demonstrated numerically that the algebraic relations accurately predict the value and variation of physical outputs of a Reynolds-averaged simulation in flow regimes that are consistent with the simplifying assumptions used to derive the solutions. The use of experimental and numerical simulation data on Reynolds stress anisotropy ratios to calibrate a Reynolds stress model is briefly illustrated. The implications of the analytical solutions for future Reynolds-averaged modeling of hydrodynamic instability-induced mixing are briefly discussed. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

Roughness topographical effects on mean momentum and stress budgets in developed turbulent channel flows

NASA Astrophysics Data System (ADS)

Aghaei Jouybari, Mostafa; Yuan, Junlin

2017-11-01

Direct numerical simulations of turbulent channel flows are carried out over two surfaces: a synthesized sand-grain surface and a realistic turbine roughness that is characterized by more prominent large-scale surface features. To separate the effects of wall-normal variation of the roughness area fraction from the (true) variation of flow statistics, the governing equations are area-averaged using intrinsic averaging, contrary to the usually practice based on the total area (i.e., superficial averaging). Additional terms appear in the mean-momentum equation resulted from the wall-normal variation of the solid fraction and play a role in the near-wall balance. Results from surfaces with a step solidity function (e.g., cubes) will also be discussed. Compared to the sand grains, the turbine surface generates stronger form-induced fluctuations, despite weaker dispersive shear stress. This is associated with more significant form-induced productions (comparable to shear production) in Reynolds stress budgets, weaker pressure work, and, consequently, more anisotropic redistribution of turbulent kinetic energy in the roughness sublayer, which potentially leads to different turbulent responses between the two surfaces in non-equilibrium flows.

Estimates of stress drop and crustal tectonic stress from the 27 February 2010 Maule, Chile, earthquake: Implications for fault strength

USGS Publications Warehouse

Luttrell, K.M.; Tong, X.; Sandwell, D.T.; Brooks, B.A.; Bevis, M.G.

2011-01-01

The great 27 February 2010 Mw 8.8 earthquake off the coast of southern Chile ruptured a ???600 km length of subduction zone. In this paper, we make two independent estimates of shear stress in the crust in the region of the Chile earthquake. First, we use a coseismic slip model constrained by geodetic observations from interferometric synthetic aperture radar (InSAR) and GPS to derive a spatially variable estimate of the change in static shear stress along the ruptured fault. Second, we use a static force balance model to constrain the crustal shear stress required to simultaneously support observed fore-arc topography and the stress orientation indicated by the earthquake focal mechanism. This includes the derivation of a semianalytic solution for the stress field exerted by surface and Moho topography loading the crust. We find that the deviatoric stress exerted by topography is minimized in the limit when the crust is considered an incompressible elastic solid, with a Poisson ratio of 0.5, and is independent of Young's modulus. This places a strict lower bound on the critical stress state maintained by the crust supporting plastically deformed accretionary wedge topography. We estimate the coseismic shear stress change from the Maule event ranged from-6 MPa (stress increase) to 17 MPa (stress drop), with a maximum depth-averaged crustal shear-stress drop of 4 MPa. We separately estimate that the plate-driving forces acting in the region, regardless of their exact mechanism, must contribute at least 27 MPa trench-perpendicular compression and 15 MPa trench-parallel compression. This corresponds to a depth-averaged shear stress of at least 7 MPa. The comparable magnitude of these two independent shear stress estimates is consistent with the interpretation that the section of the megathrust fault ruptured in the Maule earthquake is weak, with the seismic cycle relieving much of the total sustained shear stress in the crust. Copyright 2011 by the American Geophysical Union.

Abnormal tibiofemoral contact stress and its association with altered kinematics following center-center ACL reconstruction: an in vitro study

PubMed Central

Imhauser, Carl; Mauro, Craig; Choi, Daniel; Rosenberg, Eric; Mathew, Stephen; Nguyen, Joseph; Ma, Yan; Wickiewicz, Thomas

2014-01-01

Background Abnormal tibiofemoral contact stress and aberrant kinematics may influence the progression of osteoarthritis in the ACL-deficient and the ACL-reconstructed knee. However, relationships between contact stress and kinematics following ACL reconstruction are poorly understood. Therefore, we posed the following research questions: (1) How do ACL deficiency and reconstruction affect kinematics of and contact stress in the tibiofemoral joint? (2) What kinematic differences are associated with abnormal contact stress following ACL reconstruction? Hypothesis/Purpose Center-center ACL reconstruction will not restore knee kinematics and contact stress. Correlations will exist between abnormal contact stress and aberrant kinematics following ACL reconstruction will exist. Study Design Controlled laboratory study Methods Clinical tests of anterior and rotational stability were simulated on eleven cadaveric knees using an industrial robot. Tests were conducted with the ACL intact, sectioned, and after single bundle ACL reconstruction using a quadrupled hamstring autograft with tunnels drilled through the center of the native footprints. Kinematics were recorded during the tests. Contact stress was continuously recorded from a stress transducer fixed to the tibial plateau and mean contact stress was calculated regionally. Results ACL deficiency resulted in increased mean contact stress in the posterior sectors of the medial and lateral compartments under anterior and rotational loads, respectively. Reconstruction reduced stress in these locations; however contact stress abnormalities remained. On average, kinematics were overconstrained following ACL reconstruction (≤1.8mm and ≤2.6° in all directions). However, combinations of overconstrained and underconstrained motions in ab/adduction and medial-lateral translation in response to combined moments, and axial rotation, anterior-posterior and medial-lateral translation in response to an anterior load were associated with abnormal mean contact stress. Conclusions ACL reconstruction reduces high stresses generated in the posterior compartment of the ACL-deficient knee. Abnormal contact stress following ACL reconstruction is related to multiplanar variations in knee kinematics. Clinical Relevance Clinical measures of multiplanar kinematics may help to better characterize the quality of ACL reconstruction. Such measures may help identify those at increased risk of long-term joint degeneration following this surgery. PMID:23470858

Exercise mitigates cumulative associations between stress and BMI in girls age 10 to 19.

PubMed

Puterman, Eli; Prather, Aric A; Epel, Elissa S; Loharuka, Sheila; Adler, Nancy E; Laraia, Barbara; Tomiyama, A Janet

2016-02-01

Long-term psychological stress is associated with BMI increases in children as they transition to adulthood, whereas long-term maintenance of physical activity can slow excess weight gain. We hypothesized that in addition to these main effects, long-term physical activity mitigates the relationship between long-term stress and BMI increase. The NHLBI Growth and Health Study enrolled 2,379 10-year-old Black and White girls, following them annually for 10 measurement points. Growth curve modeling captured the dynamics of BMI, measured yearly, and stress and physical activity, measured at varying years. At average levels of activity and stress, with all covariates remaining fixed, average BMI at baseline was 19.74 (SE = 0.38) and increased 0.64 BMI (SE = 0.01, p < .001) units every year. However, this increase in BMI significantly varied as a function of cumulative stress and physical activity. Slower BMI gain occurred in those girls who were less stressed and more active (0.62 BMI units/year, SE = .02, p < .001), whereas the most rapid and largest growth occurred in girls who were more stressed and less active (0.92 BMI units/year, SE = .02, p < .001). Racial identification did not alter these effects. As hypothesized, in girls who maintained long-term activity, BMI growth was mitigated, even when reporting high long-term stress, compared with less physically active girls. This study adds to a converging literature in which physical activity, a modifiable prevention target, functions to potentially limit the damaging health effects of long-term psychological stress. (c) 2016 APA, all rights reserved).

The Reynolds-stress tensor in diffusion flames; An experimental and theoretical investigation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schneider, F.; Janicka, J.

1990-07-01

The authors present measurements and predictions of Reynolds-stress components and mean velocities in a CH{sub 4}-air diffusion flame. A reference beam LDA technique is applied for measuring all Reynolds-stress components. A hologram with dichromated gelatine as recording medium generates strictly coherent reference beams. The theoretical part describes a Reynolds-stress model based on Favre-averaged quantities, paying special attention to modeling the pressure-shear correlation and the dissipation equation in flames. Finally, measurement/prediction comparisons are presented.

Stresses, deformation, and seismic events on scaled experimental faults with heterogeneous fault segments and comparison to numerical modeling

NASA Astrophysics Data System (ADS)

Buijze, Loes; Guo, Yanhuang; Niemeijer, André R.; Ma, Shengli; Spiers, Christopher J.

2017-04-01

Faults in the upper crust cross-cut many different lithologies, which cause the composition of the fault rocks to vary. Each different fault rock segment may have specific mechanical properties, e.g. there may be stronger and weaker segments, and segments prone to unstable slip or creeping. This leads to heterogeneous deformation and stresses along such faults, and a heterogeneous distribution of seismic events. We address the influence of fault variability on stress, deformation, and seismicity using a combination of scaled laboratory fault and numerical modeling. A vertical fault was created along the diagonal of a 30 x 20 x 5 cm block of PMMA, along which a 2 mm thick gouge layer was deposited. Gouge materials of different characteristics were used to create various segments along the fault; quartz (average strength, stable sliding), kaolinite (weak, stable sliding), and gypsum (average strength, unstable sliding). The sample assembly was placed in a horizontal biaxial deformation apparatus, and shear displacement was enforced along the vertical fault. Multiple observations were made: 1) Acoustic emissions were continuously recorded at 3 MHz to observe the occurrence of stick-slips (micro-seismicity), 2) Photo-elastic effects (indicative of the differential stress) were recorded in the transparent set of PMMA wall-rocks using a high-speed camera, and 3) particle tracking was conducted on a speckle painted set of PMMA wall-rocks to study the deformation in the wall-rocks flanking the fault. All three observation methods show how the heterogeneous fault gouge exerts a strong control on the fault behavior. For example, a strong, unstable segment of gypsum flanked by two weaker kaolinite segments show strong stress concentrations develop near the edges of the strong segment, with at the same time most of acoustic emissions being located at the edge of this strong segment. The measurements of differential stress, strain and acoustic emissions provide a strong means to compare the scaled experiment to modeling results. In a finite-element model we reproduce the laboratory experiments, and compare the modeled stresses and strains to the observations and we compare the nucleation of seismic instability to the location of acoustic emissions. The model aids in understanding how the stresses and strains may vary as a result of fault heterogeneity, but also as a result of the boundary conditions inherent to a laboratory setup. The scaled experimental setup and modeling results also provide a means explain and compare with observations made at a larger scale, for example geodetic and seismological measurements along crustal scale faults.

Role of Perceived Stress on the Occurrence of Preterm Labor and Preterm Birth among Urban Women

PubMed Central

Seravalli, Laura; Patterson, Freda; Nelson, Deborah B.

2013-01-01

Introduction This study examined whether prenatal perceived stress levels during pregnancy were associated with preterm labor (PTL) or preterm birth (PTB). Methods Perceived stress levels were measured at 16 weeks gestation or less and between 20 and 24 weeks gestation in a sample of 1,069 low-income pregnant women attending Temple University prenatal care clinics. Scores were averaged to create a single measure of prenatal stress. PTB was defined as the occurrence of a spontaneous birth prior to 37 weeks gestation. PTL was defined as the occurrence of regular contractions between 20 and 37 weeks of pregnancy that were associated with changes in the cervix. Results Independent of potential confounding factors, prenatal perceived stress was not associated with PTL (OR 1.10; 95% CI 0.69-1.78, P = .66); however, prenatal stress trended toward an association with PTB (OR 1.49; 95% CI: 1.00-2.23, P =.05). The strongest predictor of preterm labor was a history of preterm labor in a prior pregnancy. Women with a history of PTL were two times more likely to experience PTL in the current pregnancy than women who did not have a PTL history (OR 2.16; 95% CI 1.05-4.41, P =.04). Historical risk factors of PTB, such as African American race, a history of abortion or a history of PTB were not related to PTL. The strongest predictor of PTB was having a history of PTB in a prior pregnancy (OR 2.55; 95% CI 1.54-4.24, P <.001). Discussion Prenatal perceived stress levels may be a risk factor for PTB independent of PTL; however, prenatal stress was not associated with PTL. Risk factors for PTL may be different from those of PTB. PMID:24890400

Chewing unflavored gum does not reduce cortisol levels during a cognitive task but increases the response of the sympathetic nervous system.

PubMed

Walker, Jessica; Hosiner, Andreas; Kergoat, Sophie; Walker, Joel M; Somoza, Veronika

2016-02-01

Stress might be caused by various lifestyle factors and physical challenges and can result in severe diseases. The body responds to stressful events by release of hormones, like cortisol, as well as reaction of the sympathetic nervous system. One strategy to counteract stress is chewing gum. The present study aimed at investigating the influence of mastication on biomarkers of stress during performance of a stress test. A two-armed cross-over study with 40 young male volunteers was performed. Hormone plasma concentrations were determined after an initial resting phase (2:30p.m.), immediately before (3:00p.m.) and two times after (3:20, 3:50p.m.) performance of a multitasking test using magnetic beads and ELISA methods. In addition, visual analog scales were used to rate subjective mood and the breathing and heart rates were monitored throughout the entire study period using a sensor chest belt. Performance of the stress test led to an increase in plasma cortisol concentrations from 223±23.3 to 325±38.4ng/ml (p=0.023) and caused changes in subjective mood ratings as well as breathing rates. Although chewing gum base had no impact on the plasma hormone concentrations, it induced a stronger elevation of average heart rates compared to not chewing (p=0.016). The effect of chewing gum on a mild stress load was less pronounced than in previous studies. Besides the detection of cortisol in saliva, not in plasma, in previous studies, flavored gum was used. Aroma active compounds might have substantially contributed to the beneficial effects of gum on biomarker of stress shown before. Copyright © 2015 Elsevier Inc. All rights reserved.

Algisyl-LVR™ with coronary artery bypass grafting reduces left ventricular wall stress and improves function in the failing human heart☆,☆☆

PubMed Central

Lee, Lik Chuan; Wall, Samuel T.; Klepach, Doron; Ge, Liang; Zhang, Zhihong; Lee, Randall J.; Hinson, Andy; Gorman, Joseph H.; Gorman, Robert C.; Guccione, Julius M.

2013-01-01

Background Left ventricular (LV) wall stress reduction is a cornerstone in treating heart failure. Large animal models and computer simulations indicate that adding non-contractile material to the damaged LV wall can potentially reduce myofiber stress. We sought to quantify the effects of a novel implantable hydrogel (Algisyl-LVR™) treatment in combination with coronary artery bypass grafting (i.e. Algisyl-LVR™+CABG) on both LV function and wall stress in heart failure patients. Methods and results Magnetic resonance images obtained before treatment (n=3), and at 3 months (n=3) and 6 months (n=2) afterwards were used to reconstruct the LV geometry. Cardiac function was quantified using end-diastolic volume (EDV), end-systolic volume (ESV), regional wall thickness, sphericity index and regional myofiber stress computed using validated mathematical modeling. The LV became more ellipsoidal after treatment, and both EDV and ESV decreased substantially 3 months after treatment in all patients; EDV decreased from 264±91 ml to 146±86 ml and ESV decreased from 184±85 ml to 86±76 ml. Ejection fraction increased from 32±8% to 47±18% during that period. Volumetric-averaged wall thickness increased in all patients, from 1.06±0.21 cm (baseline) to 1.3±0.26 cm (3 months). These changes were accompanied by about a 35% decrease in myofiber stress at end-of-diastole and at end-of-systole. Post-treatment myofiber stress became more uniform in the LV. Conclusions These results support the novel concept that Algisyl-LVR™+CABG treatment leads to decreased myofiber stress, restored LV geometry and improved function. PMID:23394895

[Study on the occupational stress norm and it's application for the marketing group, public service/safety group and production laborer group].

PubMed

Yang, Xin-Wei; Wang, Zhi-Ming; Jin, Tai-Yi; Lan, Ya-Jia

2006-09-01

A study of the occupational stress norm and it's application for the marketing group, public service/safety group and production laborer group. In this study, cross-sectional study method is used, and a synthetic way of sorting and randomized sampling is adopted to deal with research targets (36 marketing group, 331 public service/safety group, 903 production laborer group). Descriptive statistics for OSI-R scale scores for the marketing group, public service/safety group and production laborer group were modulated. Scale raw score to T-score conversion tables derived from the OSI-R normative sample for marketing group public service/safety group and production laborer group were established. OSI-R profile from for marketing group, public service/safety group and production laborer group were established. For the ORQ and PSQ scales, scores at or above 70 indicate a strong levels of maladaptive stress and strain. Score in the range of 60 to 69 suggest middle levels of maladaptive stress and strain. Score in the range of 40 to 59 indicate normal levels of stress and strain. Score below 40 indicate a relative absence of occupational stress and strain. For the PRQ scales, score below 30 indicate a significant lack of coping resources. Score in the range of 30 to 39 suggest middle deficits in coping resources. Score in the range of 40 to 59 indicate average coping resources. Scores at or above 60 indicate a strong levels of coping resources. The authors combined subjective and objective environment match model of occupational stress. Different intervention measure should be take to reduce the occupational stress so as to improve the work ability.

In vivo labeling and specific magnetic bead separation of RNA for biofilm characterization and stress-induced gene expression analysis in bacteria.

PubMed

Stankiewicz, Nikolai; Gold, Andrea; Yüksel, Yousra; Berensmeier, Sonja; Schwartz, Thomas

2009-12-01

The method of in vivo labeling and separation of bacterial RNA was developed as an approach to elucidating the stress response of natural bacterial populations. This technique is based on the incorporation of digoxigenin-11-uridine-5'-triphosphate (DIG-11-UTP) in the RNA of active bacteria. The digoxigenin fulfills a dual role as a label of de novo synthesized RNA and a target for magnetic bead separation from a total RNA extract. Depending on the growth conditions and the population's composition, the assembly rate of DIG-11-UTP ranged from 1.2% to 12.5% of the total RNA in gram-positive and gram-negative reference bacteria as well as in natural biofilms from drinking water, surface water, and lake sediment. Separation of DIG-RNA from total RNA extracts was performed with a biotinylated anti-digoxigenin antibody and streptavidin-functionalized magnetic particles. The average separation yield from total RNA extracts was about 95% of labeled RNA. The unspecific bindings of non-labeled nucleic acids were smaller than 0.2%, as was evaluated by spiking experiments with an unmarked DNA amplicon. Applicability of the method developed was demonstrated by rRNA-directed PCR-DGGE population analysis of natural biofilms and expression profiling of two stress-induced genes (vanA and rpoS) in reference bacteria.

Relationship Between Depression and Specific Health Indicators Among Hypertensive African American Parents and Grandparents

PubMed Central

Taylor, Jacquelyn Y.; Washington, Olivia G. M.; Artinian, Nancy T.; Lichtenberg, Peter

2010-01-01

African Americans are at greater risk for hypertension than are other ethnic groups. This study examined relationships among hypertension, stress, and depression among 120 urban African American parents and grandparents. This study is a secondary analysis of a larger nurse-managed randomized clinical trial testing the effectiveness of a telemonitoring intervention. Baseline data used in analyses, with the exception of medication compliance, were collected at 3 months' follow-up. Health indicators, perceived stress, and social support were examined to determine their relationship with depressive symptoms. A total of 48% of the variance in depressive symptomology was explained by perceived stress and support. Health indicators including average systolic blood pressure explained 21% of the variance in depressive symptomology. The regression analysis using average diastolic blood pressure explained 26% of the variance in depressive symptomology. Based on study results, African Americans should be assessed for perceived stress and social support to alleviate depressive symptomology. PMID:18843828

Bladder neck competency at rest in women with incontinence.

PubMed

English, S F; Amundsen, C L; McGuire, E J

1999-02-01

We determine the presence of an open bladder neck during video urodynamic studies and relate that finding to the presence of stress urinary incontinence. Patients presenting with urinary incontinence, voiding dysfunction or pelvic floor prolapse underwent video urodynamics. With the patient upright and after 200 ml. contrast material had been instilled into the bladder the bladder neck was viewed to determine if it was open or closed. At that point the abdominal leak point pressure was measured. Of 102 women, average age 56.5 years (range 31 to 82), 13% had an open bladder neck and demonstrable stress incontinence on video urodynamics with an average abdominal leak point pressure of 45 cm. water (range 26 to 90). Of those with stress incontinence on urodynamics 23% had an open bladder neck. No continent patient had an open bladder neck. The presence of an open bladder neck with the bladder filled to 200 ml. correlates strongly with the presence of stress incontinence.

The effect of obstructive sleep apnea on DNA damage and oxidative stress.

PubMed

Kang, Il Gyu; Jung, Joo Hyun; Kim, Seon Tae

2013-06-01

Obstructive sleep apnea syndrome (OSAS) is associated with repeated hypoxia and re-oxygenation. This characteristic of OSAS may cause oxidative stress and DNA damage. However, the link of OSAS with oxidative stress and DNA damage is still controversial. In the current study, we investigated whether OSAS causes DNA damage using alkaline single-cell gel electrophoresis (comet assay) and measuring oxidative stress by monitoring serum malondialdehyde (MDA) levels. From March 2009 to August 2010, 51 patients who underwent polysomnography (PSG) during the night were enrolled in this study. We obtained serum from the patients at 6 AM. DNA damage and oxidative stress were evaluated using a comet assay and measuring serum MDA, respectively. We divided the patients into two groups according to the existence of comets appearing in the comet assay. Group 1 included 44 patients with negative assay results and group 2 consisted of seven patients with positive comet assay findings. We compared the age, gender proportion, PSG data (respiratory disturbance index [RDI], lowest O2 saturation level, and arousal index [AI]), time of disease onset, smoking habits, and serum MDA levels between the two groups. The average age and gender proportion of the two groups were not statistically different (P>0.05). The average of RDI for group 1 was 30.4±18.4 and 8.0±7.7 (P<0.01) for group 2. The average of lowest O2 saturation level for group 1 was 81.2±7.2 and 87.4±6.5 (P<0.05) for group 2. The average AI for group 1 was 32.8±15.1 and 20.8±7.7 (P<0.05) for group 2. Similarly, serum MDA levels of the two groups were not statistically different (P>0.05). No relationship between positive comet assay results and OSAS severity was identified. Results of the current study showed that OSAS was not associated with DNA damage as measured by comet assays or oxidative stress according to serum MDA levels.

Development of a modified cortisol extraction procedure for intermediately sized fish not amenable to whole-body or plasma extraction methods.

PubMed

Guest, Taylor W; Blaylock, Reginald B; Evans, Andrew N

2016-02-01

The corticosteroid hormone cortisol is the central mediator of the teleost stress response. Therefore, the accurate quantification of cortisol in teleost fishes is a vital tool for addressing fundamental questions about an animal's physiological response to environmental stressors. Conventional steroid extraction methods using plasma or whole-body homogenates, however, are inefficient within an intermediate size range of fish that are too small for phlebotomy and too large for whole-body steroid extractions. To assess the potential effects of hatchery-induced stress on survival of fingerling hatchery-reared Spotted Seatrout (Cynoscion nebulosus), we developed a novel extraction procedure for measuring cortisol in intermediately sized fish (50-100 mm in length) that are not amenable to standard cortisol extraction methods. By excising a standardized portion of the caudal peduncle, this tissue extraction procedure allows for a small portion of a larger fish to be sampled for cortisol, while minimizing the potential interference from lipids that may be extracted using whole-body homogenization procedures. Assay precision was comparable to published plasma and whole-body extraction procedures, and cortisol quantification over a wide range of sample dilutions displayed parallelism versus assay standards. Intra-assay %CV was 8.54%, and average recovery of spiked samples was 102%. Also, tissue cortisol levels quantified using this method increase 30 min after handling stress and are significantly correlated with blood values. We conclude that this modified cortisol extraction procedure provides an excellent alternative to plasma and whole-body extraction procedures for intermediately sized fish, and will facilitate the efficient assessment of cortisol in a variety of situations ranging from basic laboratory research to industrial and field-based environmental health applications.

Empirical Green's function analysis: Taking the next step

USGS Publications Warehouse

Hough, S.E.

1997-01-01

An extension of the empirical Green's function (EGF) method is presented that involves determination of source parameters using standard EGF deconvolution, followed by inversion for a common attenuation parameter for a set of colocated events. Recordings of three or more colocated events can thus be used to constrain a single path attenuation estimate. I apply this method to recordings from the 1995-1996 Ridgecrest, California, earthquake sequence; I analyze four clusters consisting of 13 total events with magnitudes between 2.6 and 4.9. I first obtain corner frequencies, which are used to infer Brune stress drop estimates. I obtain stress drop values of 0.3-53 MPa (with all but one between 0.3 and 11 MPa), with no resolved increase of stress drop with moment. With the corner frequencies constrained, the inferred attenuation parameters are very consistent; they imply an average shear wave quality factor of approximately 20-25 for alluvial sediments within the Indian Wells Valley. Although the resultant spectral fitting (using corner frequency and ??) is good, the residuals are consistent among the clusters analyzed. Their spectral shape is similar to the the theoretical one-dimensional response of a layered low-velocity structure in the valley (an absolute site response cannot be determined by this method, because of an ambiguity between absolute response and source spectral amplitudes). I show that even this subtle site response can significantly bias estimates of corner frequency and ??, if it is ignored in an inversion for only source and path effects. The multiple-EGF method presented in this paper is analogous to a joint inversion for source, path, and site effects; the use of colocated sets of earthquakes appears to offer significant advantages in improving resolution of all three estimates, especially if data are from a single site or sites with similar site response.

A Comparison between Deep and Shallow Stress Fields in Korea Using Earthquake Focal Mechanism Inversions and Hydraulic Fracturing Stress Measurements

NASA Astrophysics Data System (ADS)

Lee, Rayeon; Chang, Chandong; Hong, Tae-kyung; Lee, Junhyung; Bae, Seong-Ho; Park, Eui-Seob; Park, Chan

2016-04-01

We are characterizing stress fields in Korea using two types of stress data: earthquake focal mechanism inversions (FMF) and hydraulic fracturing stress measurements (HF). The earthquake focal mechanism inversion data represent stress conditions at 2-20 km depths, whereas the hydraulic fracturing stress measurements, mostly conducted for geotechnical purposes, have been carried out at depths shallower than 1 km. We classified individual stress data based on the World Stress Map quality ranking scheme. A total of 20 FMF data were classified into A-B quality, possibly representing tectonic stress fields. A total of 83 HF data out of compiled 226 data were classified into B-C quality, which we use for shallow stress field characterization. The tectonic stress, revealed from the FMF data, is characterized by a remarkable consistency in its maximum stress (σ1) directions in and around Korea (N79±2° E), indicating a quite uniform deep stress field throughout. On the other hand, the shallow stress field, represented by HF data, exhibits local variations in σ1 directions, possibly due to effects of topography and geologic structures such as faults. Nonetheless, there is a general similarity in σ1 directions between deep and shallow stress fields. To investigate the shallow stress field statistically, we follow 'the mean orientation and wavelength analysis' suggested by Reiter et al. (2014). After the stress pattern analysis, the resulting stress points distribute sporadically over the country, not covering the entire region evenly. In the western part of Korea, the shallow σ1directions are generally uniform with their search radius reaching 100 km, where the average stress direction agrees well with those of the deep tectonic stress. We note two noticeable differences between shallow and deep stresses in the eastern part of Korea. First, the shallow σ1 orientations are markedly non-uniform in the southeastern part of Korea with their search radius less than 25 km. In this region, the average σ1orientation based on the entire B-C quality stress data is calculated to be 77±37° ; however, the average orientation is somewhat meaningless because of the high standard deviation. The southeastern part of Korea consists mainly of Cretaceous sedimentary basin, geologically younger than the rest of the country, where regional scale faults are intensely populated. The highly scattered stress directions in this region may represent the effect of the geologic structures on shallow stress field. Second, shallow σ1 directions in the northeastern part of Korea strike consistently to 135±12° , which is deviated by as much as 56° from the deep tectonic stress direction. This region is characterized by high altitude mountainous topography (an elevation of an order of 1 km) with its major ridge axis in the NW-SE direction. We interpret, as a rule of thumb, that the ridge-perpendicular shallow horizontal stress components may be weak, leading to the ridge-parallel components to be the maximum. Overall, there are similarity and also difference between shallow and deep stress fields. Thus, it will be necessary to differentiate the strategy to tackle the stress-related problems based on their natures.

Application of ecological momentary assessment in workplace health evaluation.

PubMed

Engelen, Lina; Chau, Josephine Y; Burks-Young, Sarah; Bauman, Adrian

2016-02-01

Issue addressed Ecological momentary assessment (EMA) involves repeated sampling of current behaviours and experiences in real-time at random intervals. EMA is an innovative measurement method for program evaluation, using mobile technology (e.g. smartphones) to collect valid contextual health promotion data with good compliance. The present study examined the feasibility of using EMA for measuring workplace health outcomes. Methods Twenty-two office-based adults were prompted at four random times per work-day during a 5-day period to respond to a short survey via a smartphone application. The prompting stopped when participants had either responded 12 times or the 5-day period had ended. The questions pertained to posture, task currently being undertaken, social interactions, musculoskeletal issues, mood, and perceptions of engagement and creativity. Results In total 156 responses were collected. Nine participants completed all 12 surveys; the average completion rate was 58% (7/12). The average completion time was initially 50s and reduced to 24s during the later surveys. On average the participants were sitting and standing in 79% and 14% of survey instances, respectively. The participants reported they were working alone at their desks in 68% of instances. Reported productivity and stress were on average 6 and 3 out of 10, respectively, but varied up to 6-8 points within one person, hence the method appears sensitive to temporal variations in perceptions and mood. Conclusion Given the rich real-time data, minimal participant burden and use of readily available technology, EMA has substantial potential in workplace health promotion evaluation through the measurement of participants' well being, activities, and behaviour change. So what? An in-the-moment method using readily available mobile technology to assess participants' perceptions, mood and activity that provides rich information with minimal participant burden is a promising way to evaluate future health promotion programs.

Short-term response of the solid Earth to cryosphere fluctuations and the earthquake cycle in south-central Alaska

NASA Astrophysics Data System (ADS)

Sauber, J. M.; Freymueller, J. T.; Han, S. C.; Davis, J. L.; Ruppert, N. A.

2016-12-01

In southern Alaska surface deformation and gravimetric change are associated with the seismic cycle as well as a strong seasonal cycle of snow accumulation and melt and a variable rate of glacier mass wastage. Numerical modeling of the solid Earth response to cryosphere change on a variety of temporal and spatial scales plays a critical role in supporting the interpretation of time-variable gravity and other geodetic data. In this study we calculate the surface displacements and stresses associated with variable spatial and temporal cryospheric loading and unloading in south-central coastal Alaska. A challenging aspect of estimating the response of the solid Earth to short-term (months to 102 years) regional cryospheric fluctuations is choosing the rock mechanics constitutive laws appropriate to this region. Here we report calculated differences in the predicted surface displacements and stresses during the GRACE time period (2002 to present). Broad-scale, GRACE-derived estimates of cryospheric mass change, along with independent snow melt onset/refreeze timing, snow depth and annual glacier wastage estimates from a variety of methods, were used to approximate the magnitude and timing of cryospheric load changes. We used the CIG finite element code PyLith to enable input of spatially complex surface loads. An as example of our evaluation of the influence of variable short-term surface loads, we calculated and contrasted the predicted surface displacements and stresses for a cooler than average and higher precipitation water year (WY12) versus a warmer than average year (WY05). Our calculation of these comparative stresses is motivated by our earlier empirical evaluation of the influence of short-term cryospheric fluctuations on the background seismic rate between 1988-2006 (Sauber and Ruppert, 2008). During the warmer than average years between 2002-2006 we found a stronger seasonal dependency in the frequency of small tectonic events in the Icy Bay region relative to cooler years. To date, we have focused our 3-D modeling on changes in the thickness of the primarily elastic layer and we also varied the Maxwell viscoelastic relaxation times for the lower crust and upper mantle. We anticipate exploring the influence of transient rheologies and testing alternate 3-D rheological structures.

Averaged null energy condition from causality

DOE PAGES

Hartman, Thomas; Kundu, Sandipan; Tajdini, Amirhossein

2017-07-14

Unitary, Lorentz-invariant quantum field theories in at spacetime obey mi-crocausality: commutators vanish at spacelike separation. For interacting theories in more than two dimensions, we show that this implies that the averaged null energy,more » $$\\int$$duT uu, must be non-negative. This non-local operator appears in the operator product expansion of local operators in the lightcone limit, and therefore contributes to n-point functions. We derive a sum rule that isolates this contribution and is manifestly positive. The argument also applies to certain higher spin operators other than the stress tensor, generating an infinite family of new constraints of the form RduX uuu∙∙∙u ≥ 0. These lead to new inequalities for the coupling constants of spinning operators in conformal field theory, which include as special cases (but are generally stronger than) the existing constraints from the lightcone bootstrap, deep inelastic scattering, conformal collider methods, and relative entropy. We also comment on the relation to the recent derivation of the averaged null energy condition from relative entropy, and suggest a more general connection between causality and information-theoretic inequalities in QFT.« less

Averaged null energy condition from causality

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hartman, Thomas; Kundu, Sandipan; Tajdini, Amirhossein

Unitary, Lorentz-invariant quantum field theories in at spacetime obey mi-crocausality: commutators vanish at spacelike separation. For interacting theories in more than two dimensions, we show that this implies that the averaged null energy,more » $$\\int$$duT uu, must be non-negative. This non-local operator appears in the operator product expansion of local operators in the lightcone limit, and therefore contributes to n-point functions. We derive a sum rule that isolates this contribution and is manifestly positive. The argument also applies to certain higher spin operators other than the stress tensor, generating an infinite family of new constraints of the form RduX uuu∙∙∙u ≥ 0. These lead to new inequalities for the coupling constants of spinning operators in conformal field theory, which include as special cases (but are generally stronger than) the existing constraints from the lightcone bootstrap, deep inelastic scattering, conformal collider methods, and relative entropy. We also comment on the relation to the recent derivation of the averaged null energy condition from relative entropy, and suggest a more general connection between causality and information-theoretic inequalities in QFT.« less

Averaged null energy condition from causality

NASA Astrophysics Data System (ADS)

Hartman, Thomas; Kundu, Sandipan; Tajdini, Amirhossein

2017-07-01

Unitary, Lorentz-invariant quantum field theories in flat spacetime obey mi-crocausality: commutators vanish at spacelike separation. For interacting theories in more than two dimensions, we show that this implies that the averaged null energy, ∫ duT uu , must be non-negative. This non-local operator appears in the operator product expansion of local operators in the lightcone limit, and therefore contributes to n-point functions. We derive a sum rule that isolates this contribution and is manifestly positive. The argument also applies to certain higher spin operators other than the stress tensor, generating an infinite family of new constraints of the form ∫ duX uuu··· u ≥ 0. These lead to new inequalities for the coupling constants of spinning operators in conformal field theory, which include as special cases (but are generally stronger than) the existing constraints from the lightcone bootstrap, deep inelastic scattering, conformal collider methods, and relative entropy. We also comment on the relation to the recent derivation of the averaged null energy condition from relative entropy, and suggest a more general connection between causality and information-theoretic inequalities in QFT.

[Work stress, health and satisfaction of life in young doctors. Results of a longitudinal study in Switzerland].

PubMed

Buddeberg-Fischer, B; Stamm, M; Buddeberg, C; Bauer, G; Hämmig, O; Klaghofer, R

2008-11-01

Based on the Effort-Reward-Imbalance Model by Siegrist a study was undertaken to find out (a) in what way young doctors assess effort and reward during their specialist training; (b) whether there are certain job stress patterns over time; and (c) what the correlations are, if any, between perceived job stress, health and satisfaction with life. Within the framework of a prospective study (2001 - 2007) 370 doctors who had just qualified and were residents in the German-speaking part of Switzerland were assessed four times by means of anonymized questionnaires. Job stress, measured by the Effort-Reward-Imbalance scale, as well as health and satisfaction with life were assessed in these doctors' 2nd (T2), 4th (T3), and 6th (T4) year of specialist training ("residents"). Stress patterns of the participants were evaluated, based on the effort and reward scale values at T2, T3, and T4, by two-step cluster analysis. Gender differences between the clusters were calculated by the 2 test and differences in the continuous variables by analysis of variance with repeated measurements. During residency the percentage of doctors who experienced an Effort-Reward-Imbalance (ratio between effort and reward ERI > 1) increased from 18% at T2 to 20 % at T3 to 25 % at T4. The cluster analysis revealed two clusters: Type 1 (67%) with effort values below average and reward values above average (ER balance) across the three measurement points, and type 2 (33 %) with effort values above average and reward values below average (ER imbalance). Subjects in cluster 2 showed unfavorable values, when compared with those in cluster 1, in overcommitment, in workload and in the health variables (anxiety, depression, physical and psychological well-being), as well as in their assessed satisfaction with life at all three measurement points. One third of the doctors experienced stress at work, caused by an effort-reward imbalance. This had a negative impact on their health and satisfaction with life. Regular supervision and goal-oriented career counselling provided by senior physicians could contribute to young doctors not feeling so much stressed at work, feeling well and being more content with their work.

Stress generation in thermally grown oxide films. [oxide scale spalling from superalloy substrates

NASA Technical Reports Server (NTRS)

Kumnick, A. J.; Ebert, L. J.

1981-01-01

A three dimensional finite element analysis was conducted, using the ANSYS computer program, of the stress state in a thin oxide film thermally formed on a rectangular piece of NiCrAl alloy. The analytical results indicate a very high compressive stress in the lateral directions of the film (approximately 6200 MPa), and tensile stresses in the metal substrate that ranged from essentially zero to about 55 MPa. It was found further that the intensity of the analytically determined average stresses could be approximated reasonably well by the modification of an equation developed previously by Oxx for stresses induced into bodies by thermal gradients.

Wavy and Cycloidal Lineament Formation on Europa from Combined Diurnal and Nonsynchronous Stresses

NASA Technical Reports Server (NTRS)

Gleeson, Damhnait; Crawford, Zane; Barr, Amy C.; Mullen, McCall; Pappalardo, Robert T.; Prockter, Louise M.; Stempel, Michelle M.; Wahr, John

2005-01-01

In a companion abstract, we show that fractures propagated into combined diurnal and nonsynchronous rotation (NSR) stress fields can be cycloidal, "wavy," or arcuate in planform as the relative proportion of NSR stress in increased. These transitions occur as NSR stress accumulates over approx. 0 to 10 deg of ice shell rotation, for average fracture propagation speeds of approx. 1 to 3 m/s. Here we consider the NSR speed parameter space for these morphological transitions, and explore the effects on cycloids of adding NSR to diurnal stress. Fitting individual Europan lineaments can constrain the combined NSR plus diurnal stress field at the time of formation.

Psychological stress and short-term hospitalisations or death in patients with heart failure.

PubMed

Endrighi, Romano; Waters, Andrew J; Gottlieb, Stephen S; Harris, Kristie M; Wawrzyniak, Andrew J; Bekkouche, Nadine S; Li, Yisheng; Kop, Willem J; Krantz, David S

2016-06-29

Standard predictors do not fully explain variations in the frequency and timing of heart failure (HF) adverse events (AEs). Psychological stress can trigger acute cardiovascular (CV) events, but it is not known whether stress can precipitate AEs in patients with HF. We investigated prospective associations of psychological stress with AEs in patients with HF. 144 patients with HF (77% male; 57.5±11.5, range 23-87 years, left ventricular ejection fraction ≤40%) were longitudinally evaluated for psychological stress (Perceived Stress Scale) and AEs (CV hospitalisations/death) at 2-week intervals for 3 months and at 9-month follow-up. 42 patients (29.2%) had at least one CV hospitalisation and nine (6.3%) died. Patients reporting high average perceived stress across study measurements had a higher likelihood of AEs during the study period compared with those with lower stress (odds ratio=1.10, 95% confidence interval=1.04 to 1.17). In contrast to average levels, increases in stress did not predict AEs (p=0.96). Perceived stress was elevated after a CV hospitalisation (B=2.70, standard error (SE)=0.93, p=0.004) suggesting that CV hospitalisations increase stress. Subsequent analysis indicated that 24 of 38 (63%) patients showed a stress increase following hospitalisation. However, a prospective association between stress and AEs was present when accounting for prior hospitalisations (B=2.43, SE=1.23, p=0.05). Sustained levels of perceived stress are associated with increased risk of AEs, and increased distress following hospitalisation occurs in many, but not all, patients with HF. Patients with chronically high stress may be an important target group for HF interventions aimed at reducing hospitalisations. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Assessment of Computational Fluid Dynamics (CFD) Models for Shock Boundary-Layer Interaction

NASA Technical Reports Server (NTRS)

DeBonis, James R.; Oberkampf, William L.; Wolf, Richard T.; Orkwis, Paul D.; Turner, Mark G.; Babinsky, Holger

2011-01-01

A workshop on the computational fluid dynamics (CFD) prediction of shock boundary-layer interactions (SBLIs) was held at the 48th AIAA Aerospace Sciences Meeting. As part of the workshop numerous CFD analysts submitted solutions to four experimentally measured SBLIs. This paper describes the assessment of the CFD predictions. The assessment includes an uncertainty analysis of the experimental data, the definition of an error metric and the application of that metric to the CFD solutions. The CFD solutions provided very similar levels of error and in general it was difficult to discern clear trends in the data. For the Reynolds Averaged Navier-Stokes methods the choice of turbulence model appeared to be the largest factor in solution accuracy. Large-eddy simulation methods produced error levels similar to RANS methods but provided superior predictions of normal stresses.

Measurement accuracy of a stressed contact lens during its relaxation period

NASA Astrophysics Data System (ADS)

Compertore, David C.; Ignatovich, Filipp V.

2018-02-01

We examine the dioptric power and transmitted wavefront of a contact lens as it releases its handling stresses. Handling stresses are introduced as part of the contact lens loading process and are common across all contact lens measurement procedures and systems. The latest advances in vision correction require tighter quality control during the manufacturing of the contact lenses. The optical power of contact lenses is one of the critical characteristics for users. Power measurements are conducted in the hydrated state, where the lens is resting inside a solution-filled glass cuvette. In a typical approach, the contact lens must be subject to long settling times prior to any measurements. Alternatively, multiple measurements must be averaged. Apart from potential operator dependency of such approach, it is extremely time-consuming, and therefore it precludes higher rates of testing. Comprehensive knowledge about the settling process can be obtained by monitoring multiple parameters of the lens simultaneously. We have developed a system that combines co-aligned a Shack-Hartmann transmitted wavefront sensor and a time-domain low coherence interferometer to measure several optical and physical parameters (power, cylinder power, aberrations, center thickness, sagittal depth, and diameter) simultaneously. We monitor these parameters during the stress relaxation period and show correlations that can be used by manufacturers to devise methods for improved quality control procedures.

Personality diatheses and Hurricane Sandy: effects on post-disaster depression

PubMed Central

Kopala-Sibley, D. C.; Kotov, R.; Bromet, E. J.; Carlson, G. A.; Danzig, A. P.; Black, S. R.; Klein, D. N.

2015-01-01

Background According to diathesis–stress models, personality traits, such as negative emotionality (NE) and positive emotionality (PE), may moderate the effects of stressors on the development of depression. However, relatively little empirical research has directly examined whether NE and PE act as diatheses in the presence of stressful life events, and no research has examined whether they moderate the effect of disaster exposure on depressive symptoms. Hurricane Sandy, the second costliest hurricane in US history, offers a unique opportunity to address these gaps. Method A total of 318 women completed measures of NE and PE 5 years prior to Hurricane Sandy. They were also assessed for lifetime depressive disorders on two occasions, the latter occurring an average of 1 year before the hurricane. Approximately 8 weeks after the disaster (mean = 8.40, s.d. = 1.48 weeks), participants completed a hurricane stress exposure questionnaire and a measure of current depressive symptoms. Results Adjusting for lifetime history of depressive disorders, higher levels of stress from Hurricane Sandy predicted elevated levels of depressive symptoms, but only in participants with high levels of NE or low levels of PE. Conclusions These findings support the role of personality in the development of depression and suggest that personality traits can be useful in identifying those most vulnerable to major stressors, including natural disasters. PMID:26619902

Association of Smoking Cessation With Financial Stress and Material Well-Being: Results From a Prospective Study of a Population-Based National Survey

PubMed Central

Siahpush, Mohammad; Spittal, Matt; Singh, Gopal K

2007-01-01

Objectives. We used 4 waves of prospective data to examine the association of smoking cessation with financial stress and material well-being. Methods. Data (n = 5699 at baseline) came from 4 consecutive waves (2001–2005) of the Household Income and Labour Dynamics in Australia survey. We used mixed models to examine the participant-specific association of smoking cessation with financial stress and material well-being. Results. On average, a smoker who quits is expected to have a 25% reduction (P<.001; odds ratio [OR]=0.75; 95% confidence interaval [CI]=0.69, 0.81) in the odds of financial stress. Similarly, the data provided strong evidence (P<.001) that a smoker who quits is likely to experience an enhanced level of material well-being. Conclusions. Our findings indicate that interventions to encourage smoking cessation are likely to improve standards of living and reduce deprivation. The findings provide grounds for encouraging the social services sector to incorporate smoking cessation efforts into their programs to enhance the material or financial conditions of disadvantaged groups. The findings also provide additional incentives for smokers to stop smoking and as such can be used in antismoking campaigns and by smoking cessation services. PMID:17971550

Plant tolerance to high temperature in a changing environment: scientific fundamentals and production of heat stress-tolerant crops

PubMed Central

Bita, Craita E.; Gerats, Tom

2013-01-01

Global warming is predicted to have a general negative effect on plant growth due to the damaging effect of high temperatures on plant development. The increasing threat of climatological extremes including very high temperatures might lead to catastrophic loss of crop productivity and result in wide spread famine. In this review, we assess the impact of global climate change on the agricultural crop production. There is a differential effect of climate change both in terms of geographic location and the crops that will likely show the most extreme reductions in yield as a result of expected extreme fluctuations in temperature and global warming in general. High temperature stress has a wide range of effects on plants in terms of physiology, biochemistry and gene regulation pathways. However, strategies exist to crop improvement for heat stress tolerance. In this review, we present recent advances of research on all these levels of investigation and focus on potential leads that may help to understand more fully the mechanisms that make plants tolerant or susceptible to heat stress. Finally, we review possible procedures and methods which could lead to the generation of new varieties with sustainable yield production, in a world likely to be challenged both by increasing population, higher average temperatures and larger temperature fluctuations. PMID:23914193

Plant tolerance to high temperature in a changing environment: scientific fundamentals and production of heat stress-tolerant crops.

PubMed

Bita, Craita E; Gerats, Tom

2013-01-01

Global warming is predicted to have a general negative effect on plant growth due to the damaging effect of high temperatures on plant development. The increasing threat of climatological extremes including very high temperatures might lead to catastrophic loss of crop productivity and result in wide spread famine. In this review, we assess the impact of global climate change on the agricultural crop production. There is a differential effect of climate change both in terms of geographic location and the crops that will likely show the most extreme reductions in yield as a result of expected extreme fluctuations in temperature and global warming in general. High temperature stress has a wide range of effects on plants in terms of physiology, biochemistry and gene regulation pathways. However, strategies exist to crop improvement for heat stress tolerance. In this review, we present recent advances of research on all these levels of investigation and focus on potential leads that may help to understand more fully the mechanisms that make plants tolerant or susceptible to heat stress. Finally, we review possible procedures and methods which could lead to the generation of new varieties with sustainable yield production, in a world likely to be challenged both by increasing population, higher average temperatures and larger temperature fluctuations.

NLTE steady-state response matrix method.

NASA Astrophysics Data System (ADS)

Faussurier, G.; More, R. M.

2000-05-01

A connection between atomic kinetics and non-equilibrium thermodynamics has been recently established by using a collisional-radiative model modified to include line absorption. The calculated net emission can be expressed as a non-local thermodynamic equilibrium (NLTE) symmetric response matrix. In the paper, this connection is extended to both cases of the average-atom model and the Busquet's model (RAdiative-Dependent IOnization Model, RADIOM). The main properties of the response matrix still remain valid. The RADIOM source function found in the literature leads to a diagonal response matrix, stressing the absence of any frequency redistribution among the frequency groups at this order of calculation.

Progressive matrix cracking in off-axis plies of a general symmetric laminate

NASA Technical Reports Server (NTRS)

Thomas, David J.; Wetherhold, Robert C.

1993-01-01

A generalized shear-lag model is derived to determine the average through-the-thickness stress state present in a layer undergoing transverse matrix cracking, by extending the method of Lee and Daniels (1991) to a general symmetric multilayered system. The model is capable of considering cracking in layers of arbitrary orientation, states of general in-plane applied loading, and laminates with a general symmetric stacking sequence. The model is included in a computer program designed for probabilistic laminate analysis, and the results are compared to those determined with the ply drop-off technique.

Occupational stressors, burnout and coping strategies between hospital and community psychiatric nurses in a Dublin region.

PubMed

McTiernan, K; McDonald, N

2015-04-01

Burnout negatively impacts the delivery of mental health services. Psychiatric nurses face stressors that are distinct from other nursing specialities. The research was conducted in Ireland and captured a relatively large sample of respondents. The results compared the stressors, coping strategies and burnout levels between hospital and community-based psychiatric nurses. Occupational stress can negatively impact on the well-being of psychiatric nurses, which in turn can lead to poor client care. There is a dearth of published research conducted in Ireland that examines stress within the discipline. A between-groups study, undertaken in February 2011, investigated stressors, burnout and coping strategies between hospital and community-based psychiatric nurses in a Dublin region. Sixty-nine participants (8 males and 61 females), aged between 18 to 60 years voluntarily completed the Mental Health Professional Stress Scale, the Maslach Burnout Inventory and the PsychNurse Methods of Coping Scale. The findings revealed that nurses were operating in a moderately stressful environment. Stressors focused on organizational issues as opposed to client issues. The main stressors identified were lack of resources, workload and organizational structures/processes. Both groups reported average levels of emotional exhaustion, low levels of depersonalization and average levels of personal accomplishment. A Mann-Whitney U-test and Independent Samples t-test found significant differences between hospital and community-based nurses regarding depersonalization and personal accomplishment, respectively. Hospital nurses reported higher depersonalization scores, and community nurses had a greater sense of personal accomplishment. The personal accomplishment scores of hospital nurses were below mental health professional norms. No significant differences emerged regarding coping strategies. Avoidant coping strategies were favoured by both groups. It is recommended that interventions aimed at increasing personal accomplishment be implemented for both groups of nurses. An investigation of perceived job control and the use of social support would also be insightful. © 2014 John Wiley & Sons Ltd.

Effect of magnesium, probiotic, and vitamin food supplementation in healthy subjects with psychological stress and evaluation of a persistent effect after discontinuing intake.

PubMed

Allaert, Francois A; Courau, Stephanie; Forestier, Anne

2016-12-01

The aim of this paper was to describe the changes in subjects' psychological stress intensity under the effect of dietary supplements of magnesium, probiotics, and vitamins after one month of intake. Observational cohort study of subject complaining of psychological stress defined by a Perceived Stress Scale (PSS 10) score of more than 21. The study covered 242 healthy volunteers, 38.6±13.6-year-old, among whom 79.8% were women. Under the effect of the supplementation of magnesium, probiotics, and vitamins, the psychological stress of the subjects decreased significantly from 34.1±4.5 to 26.2±6.1 (P<0.0001), which corresponds to an average reduction of 22.7±16.0%. Fatigue decreased even more significantly from 16.8±6.4 to 8.7±6.2 (P<0.0001), which corresponds to an average reduction of 45.0%±38.1%. Analysis showed that the psychological stress level was strictly similar one month after the treatment was discontinued and therefore clearly demonstrated that the psychological benefit was maintained over time. Stress and fatigue are significantly reduced by the intake of a food supplement with probiotics, magnesium, vitamins, and minerals and this effect is fully maintained one month after discontinuing the food supplement intake.

Influences of granular constraints and surface effects on the heterogeneity of elastic, superelastic, and plastic responses of polycrystalline shape memory alloys

DOE PAGES

Paranjape, Harshad M.; Paul, Partha P.; Sharma, Hemant; ...

2017-02-16

Deformation heterogeneities at the microstructural length-scale developed in polycrystalline shape memory alloys (SMAs) during superelastic loading are studied using both experiments and simulations. In situ X-ray diffraction, specifically the far-field high energy diffraction microscopy (ff-HEDM) technique, was used to non-destructively measure the grain-averaged statistics of position, crystal orientation, elastic strain tensor, and volume for hundreds of austenite grains in a superelastically loaded nickel-titanium (NiTi) SMA. These experimental data were also used to create a synthetic microstructure within a finite element model. The development of intragranular stresses were then simulated during tensile loading of the model using anisotropic elasticity. Driving forcesmore » for phase transformation and slip were calculated from these stresses. The grain-average responses of individual austenite crystals examined before and after multiple stress-induced transformation events showed that grains in the specimen interior carry more axial stress than the surface grains as the superelastic response "shakes down". Examination of the heterogeneity within individual grains showed that regions near grain boundaries exhibit larger stress variation compared to the grain interiors. As a result, this intragranular heterogeneity is more strongly driven by the constraints of neighboring grains than the initial stress state and orientation of the individual grains.« less

Influences of granular constraints and surface effects on the heterogeneity of elastic, superelastic, and plastic responses of polycrystalline shape memory alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paranjape, Harshad M.; Paul, Partha P.; Sharma, Hemant

Deformation heterogeneities at the microstructural length-scale developed in polycrystalline shape memory alloys (SMAs) during superelastic loading are studied using both experiments and simulations. In situ X-ray diffraction, specifically the far-field high energy diffraction microscopy (ff-HEDM) technique, was used to non-destructively measure the grain-averaged statistics of position, crystal orientation, elastic strain tensor, and volume for hundreds of austenite grains in a superelastically loaded nickel-titanium (NiTi) SMA. These experimental data were also used to create a synthetic microstructure within a finite element model. The development of intragranular stresses were then simulated during tensile loading of the model using anisotropic elasticity. Driving forcesmore » for phase transformation and slip were calculated from these stresses. The grain-average responses of individual austenite crystals examined before and after multiple stress-induced transformation events showed that grains in the specimen interior carry more axial stress than the surface grains as the superelastic response "shakes down". Examination of the heterogeneity within individual grains showed that regions near grain boundaries exhibit larger stress variation compared to the grain interiors. As a result, this intragranular heterogeneity is more strongly driven by the constraints of neighboring grains than the initial stress state and orientation of the individual grains.« less

Numerical simulation of elasto-plastic deformation of composites: evolution of stress microfields and implications for homogenization models

NASA Astrophysics Data System (ADS)

González, C.; Segurado, J.; LLorca, J.

2004-07-01

The deformation of a composite made up of a random and homogeneous dispersion of elastic spheres in an elasto-plastic matrix was simulated by the finite element analysis of three-dimensional multiparticle cubic cells with periodic boundary conditions. "Exact" results (to a few percent) in tension and shear were determined by averaging 12 stress-strain curves obtained from cells containing 30 spheres, and they were compared with the predictions of secant homogenization models. In addition, the numerical simulations supplied detailed information of the stress microfields, which was used to ascertain the accuracy and the limitations of the homogenization models to include the nonlinear deformation of the matrix. It was found that secant approximations based on the volume-averaged second-order moment of the matrix stress tensor, combined with a highly accurate linear homogenization model, provided excellent predictions of the composite response when the matrix strain hardening rate was high. This was not the case, however, in composites which exhibited marked plastic strain localization in the matrix. The analysis of the evolution of the matrix stresses revealed that better predictions of the composite behavior can be obtained with new homogenization models which capture the essential differences in the stress carried by the elastic and plastic regions in the matrix at the onset of plastic deformation.

Oxidative Stress, Motor Abilities, and Behavioral Adjustment in Children Treated for Acute Lymphoblastic Leukemia.

PubMed

Hockenberry, Marilyn J; Krull, Kevin R; Insel, Kathleen C; Harris, Lynnette L; Gundy, Patricia M; Adkins, Kristin B; Pasvogel, Alice E; Taylor, Olga A; Koerner, Kari M; Montgomery, David W; Ross, Adam K; Hill, Adam; Moore, Ida M

2015-09-01

To examine associations among oxidative stress, fine and visual-motor abilities, and behavioral adjustment in children receiving chemotherapy for acute lymphoblastic leukemia (ALL)
. A prospective, repeated-measures design
. Two pediatric oncology settings in the southwestern United States. 89 children with ALL were followed from diagnosis to the end of chemotherapy. Serial cerebrospinal fluid samples were collected during scheduled lumbar punctures and analyzed for oxidative stress biomarkers. Children completed fine motor dexterity, visual processing speed, and visual-motor integration measures at three time points. Parents completed child behavior ratings at the same times. Oxidative stress, fine motor dexterity, visual processing, visual-motor integration, and behavioral adjustment
. Children with ALL had below-average fine motor dexterity, visual processing speed, and visual-motor integration following the induction phase of ALL therapy. By end of therapy, visual processing speed normalized, and fine motor dexterity and visual-motor integration remained below average. Oxidative stress measures correlated with fine motor dexterity and visual-motor integration. Decreased motor functioning was associated with increased hyperactivity and anxiety
. Oxidative stress occurs following chemo-therapy for childhood ALL and is related to impaired fine motor skills and visual symptoms
. Early intervention should be considered to prevent fine motor and visual-spatial deficits, as well as behavioral problems.

Stress generation and evolution in oxide heteroepitaxy

NASA Astrophysics Data System (ADS)

Fluri, Aline; Pergolesi, Daniele; Wokaun, Alexander; Lippert, Thomas

2018-03-01

Many physical properties of oxides can be changed by inducing lattice distortions in the crystal through heteroepitaxial growth of thin films. The average lattice strain can often be tuned by changing the film thickness or using suitable buffer layers between film and substrate. The exploitation of the full potential of strain engineering for sample or device fabrication rests on the understanding of the fundamental mechanisms of stress generation and evolution. For this study an optical measurement of the substrate curvature is used to monitor in situ how the stress builds up and relaxes during the growth of oxide thin films by pulsed laser deposition. The relaxation behavior is correlated with the growth mode, which is monitored simultaneously with reflection high-energy electron diffraction. The stress relaxation data is fitted and compared with theoretical models for stress evolution which were established for semiconductor epitaxy. The initial stage of the growth appears to be governed by surface stress and surface energy effects, while the subsequent stress relaxation is found to be fundamentally different between films grown on single-crystal substrates and on buffer layers. The first case can be rationalized with established theoretical models, but these models fail in the attempt to describe the growth on buffer layers. This is most probably due to the larger average density of crystalline defects in the buffer layers, which leads to a two-step stress relaxation mechanism, driven first by the nucleation and later by the migration of dislocation lines.

Evaluating the interplay between spirituality, personality and stress.

PubMed

Labbé, Elise E; Fobes, Ashley

2010-06-01

Spirituality and the big five personality traits may be risk or protective factors for coping with stress. We hypothesized young adults who reported higher spirituality ratings would demonstrate lower sympathetic nervous system arousal and better emotional coping when exposed to a laboratory stressor compared to those who rated themselves lower in spirituality. We also compared spirituality groups on trait anger, neuroticism, conscientiousness, extraversion, agreeableness and openness to experience. Eighty participants completed trait-state anger, personality and spirituality questionnaires and were grouped into low, average and high spirituality. Participants' physiological responses were monitored before and during a stressful event. Significant differences were found between low, average and high spirituality groups' respiration rate and emotional response to the stressor. Significant differences were also found between spirituality groups in extraversion, agreeableness, conscientiousness, trait anger and neuroticism. Females reported higher levels of spirituality and conscientiousness than males.

Geothermal production and reduced seismicity: Correlation and proposed mechanism

NASA Astrophysics Data System (ADS)

Cardiff, Michael; Lim, David D.; Patterson, Jeremy R.; Akerley, John; Spielman, Paul; Lopeman, Janice; Walsh, Patrick; Singh, Ankit; Foxall, William; Wang, Herbert F.; Lord, Neal E.; Thurber, Clifford H.; Fratta, Dante; Mellors, Robert J.; Davatzes, Nicholas C.; Feigl, Kurt L.

2018-01-01

At Brady Hot Springs, a geothermal field in Nevada, heated fluids have been extracted, cooled, and re-injected to produce electrical power since 1992. Analysis of daily pumping records and catalogs of microseismicity between 2010 and 2015 indicates a statistically significant correlation between days when the daily volume of production was at or above its long-term average rate and days when no seismic event was detected. Conversely, shutdowns in pumping for plant maintenance correlate with increased microseismicity. We hypothesize that the effective stress in the subsurface has adapted to the long-term normal operations (deep extraction) at the site. Under this hypothesis, extraction of fluids inhibits fault slip by increasing the effective stress on faults; in contrast, brief pumping cessations represent times when effective stress is decreased below its long-term average, increasing the likelihood of microseismicity.

Social impact of peripheral nerve injuries.

PubMed

Wojtkiewicz, Danielle M; Saunders, James; Domeshek, Leahthan; Novak, Christine B; Kaskutas, Vicki; Mackinnon, Susan E

2015-06-01

Disorders involving the peripheral nervous system can have devastating impacts on patients' daily functions and routines. There is a lack of consideration of the impact of injury on social/emotional well-being and function. We performed a retrospective database and chart review of adult patients presenting between 2010 and 2012 with peripheral nerve compression, brachial plexus injury, thoracic outlet syndrome (TOS), or neuromas. At the initial assessment, patients completed a questionnaire used to obtain demographic and psychosocial variable data including the (1) average level of pain over the last month, (2) self-perceived depression, (3) how much pain impacts quality of life (QoL), (4) current level of stress, and (5) ability to cope with stress. Statistical analyses were used to assess the differences between the dependent variables and diagnostic and demographic groups. This study included 490 patients (mean age 50 ± 15 years); the most common diagnosis was single nerve compression (n = 171). Impact on QoL was significantly greater in patients with TOS, cutaneous peroneal compressions, and neuroma versus single site nerve compressions. Average pain, impact on QoL, and stress at home were significantly higher in females versus males. Impact on QoL was correlated with average pain, depression, stress at home, and ability to cope with stress at home. Our study demonstrates that patients with single site nerve compression neuropathies experience fewer negative psychosocial effects compared to patients with more proximal upper extremity peripheral nerve disorders and neuromas. The impact on QoL was strongly correlated with pain and depression, where patients with neuromas and painful peroneal nerve entrapments reported greater detriments to QoL.

Drivers of self-reported heat stress in the Australian labour force.

PubMed

Zander, Kerstin K; Moss, Simon A; Garnett, Stephen T

2017-01-01

Heat stress causes reductions in well-being and health. As average annual temperatures increase, heat stress is expected to affect more people. While most research on heat stress has explored how exposure to heat affects functioning of the human organism, stress from heat can be manifest long before clinical symptoms are evident, with profound effects on behavior. Here we add to the little research conducted on these subclinical effects of environmental heat using results from an Australian-wide cross-sectional study of nearly 2000 respondents on their self-reported level of heat stress. Slightly less than half (47%) of the respondents perceived themselves as at least sometimes, often or very often stressed by heat during the previous 12 months. Health status and smoking behavior had the expected impact on self-reported perceived heat stress. There were also regional differences with people living in South Australia, Victoria and New South Wales most likely to have reported to have felt heat stressed. People generally worried about climate change, who had been influenced by recent heat waves and who thought there was a relationship between climate change and health were also more likely to have been heat stressed. Surprisingly average maximum temperatures did not significantly explain heat stress but stress was greater among people who perceived the day of the survey as hotter than usual. Currently heat stress indices are largely based on monitoring the environment and physical limitations to people coping with heat. Our results suggest that psychological perceptions of heat need to be considered when predicting how people will be affected by heat under climate change and when developing heat relief and climate change adaptation plans, at work, at home or in public spaces. We further conclude that the perception of temperature and heat stress complements measures that assess heat exposure and heat strain. Copyright © 2016 Elsevier Inc. All rights reserved.

Evaluation of the Effect of Surface Finish on High-Cycle Fatigue of SLM-IN718

NASA Technical Reports Server (NTRS)

Lambert, D. M.

2016-01-01

The surface finish of parts produced by additive manufacturing processes is much rougher than the surface finish generated by machining processes, and a rougher surface can reduce the fatigue strength of a part. This paper discusses an effort to quantify that reduction of strength in high-cycle fatigue for selective laser melt (SLM) coupons. A high-cycle fatigue (HCF) knockdown factor was estimated for Inconel 718, manufactured with the SLM process. This factor is the percentage reduction from the maximum stress in fatigue for low-stress ground (LSG) specimens to the maximum stress of those left with the original surface condition at the same fatigue life. Specimens were provided by a number of vendors, free to use their "best practice"; only one heat treat condition was considered; and several test temperatures were characterized, including room temperature, 800F, 1000F, and 1200F. The 1000F data had a large variance, and was omitted from consideration in this document. A first method used linear approximations extracted from the graphs, and only where data was available for both. A recommended knockdown factor of the as-built surface condition (average roughness of approximately 245 micro-inches/inch) versus low-stress ground condition (roughness no more than 4 micro-inches/inch) was established at approximately 1/3 or 33%. This is to say that for the as-built surface condition, a maximum stress of 2/3 of the stress for LSG can be expected to produce a similar life in the as-built surface condition. In this first evaluation, the knockdown factor did not appear to be a function of temperature. A second approach, the "KP method", incorporated the surface finish measure into a new parameter termed the pseudo-stress intensity factor, Kp, which was formulated to be similar to the fracture mechanics stress intensity factor. Using Kp, the variance seemed to be reduced across all sources, and knockdown factors were estimated using Kp over the range where data occurred. A plot of the results suggests that the knockdown factor is a function of temperature, and that for low lives the knockdown might be lower than the knockdown observed above about one million cycles, where it tended to stabilize. This was not universal for all temperatures tested. The higher temperature tests are thought to be influenced by the test temperature, which perhaps continued the aging process. Further evaluation of the method is suggested.

A new approach on stress-related depression and anxiety: Neuro-Psycho- Physical-Optimization with Radio Electric Asymmetric-Conveyer.

PubMed

Rinaldi, Salvatore; Fontani, Vania; Moretti, Elena; Rosettani, Barbara; Aravagli, Lucia; Saragò, Giorgio; Collodel, Giulia

2010-08-01

Chronic social stress is an important factor responsible for the worsening of depressive disorders in humans. In this study we present the relational Neuro-Psycho-Physical Optimization (NPPO) with Radio Electric Asymmetric Conveyer (REAC-CRM) as the treatment to tackle the unconscious dysfunction adjustments carried out by the central nervous system as a response to environmental stresses. Psychological stress was measured in a group of 888 patients using the Psychological Stress Measure (PSM) test, a self-administered questionnaire. Data were collected immediately before and after the 4-wk therapy cycle. The detection of anxiety and depression clusters by PSM test has been based on the Diagnostic and Statistical Manual of Mental Disorders (DSM-IV-TR, APA, 2000) criteria. Six hundred and eighty eight patients (212 males, 476 females, average PSM test total scores 107.9 +/- 23.13) were treated with REAC-CRM therapy; 200 (64 males, 136 females, average PSM test total scores 107.86 +/- 25.80) were treated with "placebo REAC-CRM therapy"and used as control. This study showed a significant reduction in scores measuring subjective perceptions of stress in the patients treated with a cycle of REAC-CRM therapy. At the end-point the number of patients reporting symptoms of stress-related anxiety and depression on the PSM test was significantly reduced (P<0.001); in the placebo group no significant difference was highlighted. NPPO therapy with a cycle of REAC-CRM was shown to reduce subjective perceptions of stress measured by the PSM test and in particular, symptoms of stress-related anxiety and depression.

Effects of a veterinary student leadership program on measures of stress and academic performance.

PubMed

Moore, Dale A; Truscott, Marla L; St Clair, Lisa; Klingborg, Donald J

2007-01-01

Assuming leadership roles in veterinary student governance or club activities could be considered an added stressor for students because of the impact on time available for personal and academic activities. The study reported here evaluated the effects of participation in a leadership program and leadership activity across two classes of veterinary students on measures of stress, using the Derogatis Stress Profile (DSP), and on veterinary school academic performance, measured as annual grade-point average (GPA) over a three-year period. Program participants and their classmates completed the DSP three times across the first three years of veterinary school. On average, participating students reported self-declared stress levels that were higher and measured DSP stress levels that were lower than those of the general population. Students were more likely to assume elected or appointed leadership roles while in their first three years of the veterinary degree program if they participated in the optional leadership program and demonstrated lower stress in several dimensions. Some increased stress, as measured in some of the DSP stress dimensions, had a small but statistically significant influence on professional school GPA. The study determined that the most important predictors of students' cumulative GPA across the three-year period were the GPA from the last 45 credits of pre-veterinary coursework and their quantitative GRE scores. The results of the study indicate that neither participation in the leadership program nor taking on leadership roles within veterinary school appeared to influence veterinary school academic performance or to increase stress.

Impact of average household income and damage exposure on post-earthquake distress and functioning: A community study following the February 2011 Christchurch earthquake.

PubMed

Dorahy, Martin J; Rowlands, Amy; Renouf, Charlotte; Hanna, Donncha; Britt, Eileen; Carter, Janet D

2015-08-01

Post-traumatic stress, depression and anxiety symptoms are common outcomes following earthquakes, and may persist for months and years. This study systematically examined the impact of neighbourhood damage exposure and average household income on psychological distress and functioning in 600 residents of Christchurch, New Zealand, 4-6 months after the fatal February, 2011 earthquake. Participants were from highly affected and relatively unaffected suburbs in low, medium and high average household income areas. The assessment battery included the Acute Stress Disorder Scale, the depression module of the Patient Health Questionnaire (PHQ-9), and the Generalized Anxiety Disorder Scale (GAD-7), along with single item measures of substance use, earthquake damage and impact, and disruptions in daily life and relationship functioning. Controlling for age, gender and social isolation, participants from low income areas were more likely to meet diagnostic cut-offs for depression and anxiety, and have more severe anxiety symptoms. Higher probabilities of acute stress, depression and anxiety diagnoses were evident in affected versus unaffected areas, and those in affected areas had more severe acute stress, depression and anxiety symptoms. An interaction between income and earthquake effect was found for depression, with those from the low and medium income affected suburbs more depressed. Those from low income areas were more likely, post-earthquake, to start psychiatric medication and increase smoking. There was a uniform increase in alcohol use across participants. Those from the low income affected suburb had greater general and relationship disruption post-quake. Average household income and damage exposure made unique contributions to earthquake-related distress and dysfunction. © 2014 The British Psychological Society.

Determining molecular responses to environmental change in soybeans

USDA-ARS?s Scientific Manuscript database

As the global climate changes, plants will be challenged by environmental stresses that are more extreme and more frequent. The average yield loss due to environmental stresses is currently estimated to be more than 50% for major crop species and is the major limitation to world food production. The...

A Study of Factors Associated with Fifth-Year Teacher Interns' Concerns, Problems, and Stress.

ERIC Educational Resources Information Center

Butler, E. Dean; Smith, Dennie L.

Fuller's theoretical model of concerns was the conceptual framework used in studying concerns, problems, and stress levels of three cohorts of interns undergoing transition into teaching. Independent variables examined included undergraduate grade point averages, subject area specializations, age, and personality. Subjects were fifth-year…

Global climate change and toxicology: Exacerbation of toxicity of pollutants by thermal stress

EPA Science Inventory

Relatively small elevations in the average global temperature can translate to greater incidences of heat alerts during the summer months, an effect that is especially prevalent in urban areas where simultaneous exposure to heat stress and excessive levels of air pollutants is co...

Bus drivers' mental conditions and their relation to bus passengers' accidents with a focus on the psychological stress concept.

PubMed

Yamada, Yasuyuki; Mizuno, Motoki; Sugiura, Miyuki; Tanaka, Sumio; Mizuno, Yuki; Yanagiya, Toshio; Hirosawa, Masataka

2008-06-01

The purpose of this study was to clarify the psychological factors of bus drivers' instability that were related to bus passengers' accidents according to the hypothesis model based on the stress concept of Lazarus and Folkman (1984). This research was carried out in 2006. Participants of the study were 39 Japanese male bus drivers. Their average age was 40.2 (SD: 11.1). The average duration of employment was 4.5 (SD:6.1) years. A questionnaire was used that was composed of items concerning the frequency of bus passengers' accidents, performance of safe driving, job stressors, stress reaction and recognition from others. Based on the results, a model assuming that stress reaction caused by job stressors disturbed the bus driver's safe driving and was associated with passengers' accidents in the bus was verified to some degree. Especially, melancholy and tired feeling toward passengers showed a strong relation to the passengers' accidents in the bus. This suggested much room for intervention. Moreover, the recognition from others of their job was confirmed to act as a control factor of the stress reaction.

The effect of stress and incentive magnetic field on the average volume of magnetic Barkhausen jump in iron

NASA Astrophysics Data System (ADS)

Shu, Di; Guo, Lei; Yin, Liang; Chen, Zhaoyang; Chen, Juan; Qi, Xin

2015-11-01

The average volume of magnetic Barkhausen jump (AVMBJ) v bar generated by magnetic domain wall irreversible displacement under the effect of the incentive magnetic field H for ferromagnetic materials and the relationship between irreversible magnetic susceptibility χirr and stress σ are adopted in this paper to study the theoretical relationship among AVMBJ v bar(magneto-elasticity noise) and the incentive magnetic field H. Then the numerical relationship among AVMBJ v bar, stress σ and the incentive magnetic field H is deduced. Utilizing this numerical relationship, the displacement process of magnetic domain wall for single crystal is analyzed and the effect of the incentive magnetic field H and the stress σ on the AVMBJ v bar (magneto-elasticity noise) is explained from experimental and theoretical perspectives. The saturation velocity of Barkhausen jump characteristic value curve is different when tensile or compressive stress is applied on ferromagnetic materials, because the resistance of magnetic domain wall displacement is different. The idea of critical magnetic field in the process of magnetic domain wall displacement is introduced in this paper, which solves the supersaturated calibration problem of AVMBJ - σ calibration curve.

Thermal infrared imaging of the temporal variability in stomatal conductance for fruit trees

NASA Astrophysics Data System (ADS)

Struthers, Raymond; Ivanova, Anna; Tits, Laurent; Swennen, Rony; Coppin, Pol

2015-07-01

Repeated measurements using thermal infrared remote sensing were used to characterize the change in canopy temperature over time and factors that influenced this change on 'Conference' pear trees (Pyrus communis L.). Three different types of sensors were used, a leaf porometer to measure leaf stomatal conductance, a thermal infrared camera to measure the canopy temperature and a meteorological sensor to measure weather variables. Stomatal conductance of water stressed pear was significantly lower than in the control group 9 days after stress began. This decrease in stomatal conductance reduced transpiration, reducing evaporative cooling that increased canopy temperature. Using thermal infrared imaging with wavelengths between 7.5 and13 μm, the first significant difference was measured 18 days after stress began. A second order derivative described the average rate of change of the difference between the stress treatment and control group. The average rate of change for stomatal conductance was 0.06 (mmol m-2 s-1) and for canopy temperature was -0.04 (°C) with respect to days. Thermal infrared remote sensing and data analysis presented in this study demonstrated that the differences in canopy temperatures between the water stress and control treatment due to stomata regulation can be validated.

Streambed stresses and flow around bridge piers

USGS Publications Warehouse

Parola, A.C.; Ruhl, K.J.; Hagerty, D.J.; Brown, B.M.; Ford, D.L.; Korves, A.A.

1996-01-01

Scour of streambed material around bridge foundations by floodwaters is the leading cause of catastrophic bridge failure in the United States. The potential for scour and the stability of riprap used to protect the streambed from scour during extreme flood events must be known to evaluate the likelihood of bridge failure. A parameter used in estimating the potential for scour and removal of riprap protection is the time-averaged shear stress on the streambed often referred to as boundary stress. Bridge components, such as bridge piers and abutments, obstruct flow and induce strong vortex systems that create streambed or boundary stresses significantly higher than those in unobstructed flow. These locally high stresses can erode the streambed around pier and abutment foundations to the extent that the foundation is undermined, resulting in settlement or collapse of bridge spans. The purpose of this study was to estimate streambed stresses at a bridge pier under full-scale flow conditions and to compare these stresses with those obtained previously in small-scale model studies. Two-dimensional velocity data were collected for three flow conditions around a bridge pier at the Kentucky State Highway 417 bridge over the Green River at Greensburg in Green County, Ky. Velocity vector plots and the horizontal component of streambed stress contour plots were developed from the velocity data. The streambed stress contours were developed using both a near-bed velocity and velocity gradient method. Maximum near-bed velocities measured at the pier for the three flow conditions were 1.5, 1.6, and 2.0 times the average near-bed velocities measured in the upstream approach flow. Maximum streambed stresses for the three flow conditions were determined to be 10, 15, and 36 times the streambed stresses of the upstream approach flow. Both the near-bed velocity measurements and approximate maximum streambed stresses at the full-scale pier were consistent with those observed in experiments using small-scale models in which similar data were collected, except for a single observation of the near-bed velocity data and the corresponding streambed stress determination. The location of the maximum streambed stress was immediately downstream of a 90 degree radial of the upstream cylinder (with the center of the upstream cylinder being the origin) for the three flow conditions. This location was close to the flow wake separation point at the upstream cylinder. Other researchers have observed the maximum streambed stress around circular cylinders at this location or at a location immediately upstream of the wake separation point. Although the magnitudes of the estimated streambed stresses measured at the full-scale pier were consistent with those measured in small-scale model studies, the stress distributions were significantly different than those measured in small-scale models. The most significant discrepancies between stress contours developed in this study and those developed in the small-scale studies for flow around cylindrical piers on a flat streambed were associated with the shape of the stress contours. The extent of the high stress region of the streambed around the full-scale pier was substantially larger than the diameter of the upstream cylinder, while small-scale models had small regions compared to the diameter of the model cylinders. In addition, considerable asymmetry in the stress contours was observed. The large region of high stress and asymmetry was attributed to several factors including (1) the geometry of the full-scale pier, (2) the non-planar topography of the streambed, (3) the 20 degree skew of the pier to the approaching flow, and (4) the non-uniformity of the approach flow. The extent of effect of the pier on streambed stresses was found to be larger for the full-scale site than for model studies. The results from the model studies indicated that the streambed stresses created by the obstruction of flow by the 3-foot wide pi

A study of job stress and burnout and related factors in the hospital personnel of Iran.

PubMed

Abarghouei, Mohammad Reza; Sorbi, Mohammad Hossein; Abarghouei, Mehdi; Bidaki, Reza; Yazdanpoor, Shirin

2016-07-01

Job stress has become one of the main factors in reducing efficiency and the loss of human resources that may cause physical and psychological adverse effects in employees. Hospital personnel are facing different stressful events, such as birth, pain and death, in a single day. Hence, identifying the job stress rates and related factors may be effective in offering proper strategies. Therefore, the present research was done to study the rate of job stress and burnout in hospital personnel and compare some of the related factors in hospitals personnel of Yazd, Iran. This cross-sectional study was conducted on 306 hospital personnel (Male: 114, Female: 192) in Yazd in 2015-16. The data were collected using a demographic questionnaire, Maslach Burnout Inventory (MBI), and Hospital Stress (HSS-35). SPSS-16 software and Pearson-product moment correlation and independent-samples t-test were used for data analysis. The mean job stress score was above average. The mean burnout dimensions that were above average included emotional exhaustion (21.7 ± 7.27), depersonalization (9.61 ± 3.74) and personal accomplishment (26.80 ± 6.17). While Pearson correlation revealed a significant positive relationship between job stress, emotional exhaustion, and depersonalization, there was a negative relationship between job stress and personal accomplishment (p < 0.01). Independent-samples t-test results showed that the rate of job stress, emotional exhaustion, and depersonalization in males is higher than females, married people have more emotional exhaustion than single ones, and, finally, health staff have more job stress than administrative staff. At the same time, the administrative staff and females have better personal accomplishment than other groups (p < 0.05). Since the rate of job stress in hospital personnel is worrying and it has adverse effects on personnel health, effective strategies on physical and mental health, such as employment support and stress management training, seem crucial to enhance physical and psychological health of hospital personnel.

Salivary Nerve Growth Factor Response to Intense Stress: Effect of Sex and Body Mass Index

DTIC Science & Technology

2014-01-01

the roles of age, sex, education, and BMI. sNGF increased 137% from baseline to intense stress. During recovery, sNGF remained elevated an average of...225 250 275 300 325 BASELI NE STRE SS RECOVERY sN G F (p g/ m L) *† * Figure 1 Effect of intense stress exposure on salivary nerve growth factor...neurotrophic responses to severe stress may play a role in the well docu- mented sex imbalance in these disorders. In particular, the failure to launch

Material Properties from Air Puff Corneal Deformation by Numerical Simulations on Model Corneas.

PubMed

Bekesi, Nandor; Dorronsoro, Carlos; de la Hoz, Andrés; Marcos, Susana

2016-01-01

To validate a new method for reconstructing corneal biomechanical properties from air puff corneal deformation images using hydrogel polymer model corneas and porcine corneas. Air puff deformation imaging was performed on model eyes with artificial corneas made out of three different hydrogel materials with three different thicknesses and on porcine eyes, at constant intraocular pressure of 15 mmHg. The cornea air puff deformation was modeled using finite elements, and hyperelastic material parameters were determined through inverse modeling, minimizing the difference between the simulated and the measured central deformation amplitude and central-peripheral deformation ratio parameters. Uniaxial tensile tests were performed on the model cornea materials as well as on corneal strips, and the results were compared to stress-strain simulations assuming the reconstructed material parameters. The measured and simulated spatial and temporal profiles of the air puff deformation tests were in good agreement (< 7% average discrepancy). The simulated stress-strain curves of the studied hydrogel corneal materials fitted well the experimental stress-strain curves from uniaxial extensiometry, particularly in the 0-0.4 range. Equivalent Young´s moduli of the reconstructed material properties from air-puff were 0.31, 0.58 and 0.48 MPa for the three polymer materials respectively which differed < 1% from those obtained from extensiometry. The simulations of the same material but different thickness resulted in similar reconstructed material properties. The air-puff reconstructed average equivalent Young´s modulus of the porcine corneas was 1.3 MPa, within 18% of that obtained from extensiometry. Air puff corneal deformation imaging with inverse finite element modeling can retrieve material properties of model hydrogel polymer corneas and real corneas, which are in good correspondence with those obtained from uniaxial extensiometry, suggesting that this is a promising technique to retrieve quantitative corneal biomechanical properties.

Retinal flavoprotein autofluorescence as a measure of retinal health.

PubMed

Elner, Susan G; Elner, Victor M; Field, Matthew G; Park, Seung; Heckenlively, John R; Petty, Howard R

2008-01-01

To establish that increased autofluorescence of mitochondrial flavoproteins, an indicator of mitochondrial oxidative stress, correlates with retinal cell dysfunction. Retinal flavoprotein autofluorescence (FA) was imaged in humans with a fundus camera modified with 467DF8-nm excitation and 535-nm emission filters and a back-illuminated, electron-multiplying, charge-coupled device camera interfaced with a computer equipped with customized image capture software. Multiple digital images, centered on the fovea, were obtained from each eye. Histograms of pixel intensities in grayscale units were analyzed for average intensity and average curve width. Adults with diabetes mellitus, age-related macular degeneration (ARMD), central serous retinopathy, and retinal dystrophies, as well as healthy control volunteers, were imaged. Monolayers of cultured human retinal pigment epithelial (HRPE) cells, HRPE cells exposed to sublethal doses of H2O2, and HRPE cells exposed to H2O2 in the presence of antioxidants were imaged for FA using fluorescent photomicroscopy. Control patients demonstrated low levels of retinal FA, which increased progressively with age. Diabetics without visible retinopathy demonstrated increased FA levels compared to control volunteers (P < .001). Diabetics with retinopathy demonstrated significantly higher FA values than those without retinopathy (P < .04). Patients with ARMD, central serous retinopathy, or retinal dystrophies also demonstrated significantly increased FA. Compared to control RPE cells, cells oxidatively stressed with H2O2 had significantly elevated FA (P < .05), which was prevented by antioxidants (P < .05). Retinal FA is significantly increased with age and diseases known to be mediated by oxidative stress. Retinal FA imaging may provide a novel, noninvasive method of assessing retinal health and retinal dysfunction prior to retinal cell death.

Phenotypic characteristics of early Wolfram syndrome

PubMed Central

2013-01-01

Background Wolfram Syndrome (WFS:OMIM 222300) is an autosomal recessive, progressive, neurologic and endocrinologic degenerative disorder caused by mutations in the WFS1 gene, encoding the endoplasmic reticulum (ER) protein wolframin, thought to be involved in the regulation of ER stress. This paper reports a cross section of data from the Washington University WFS Research Clinic, a longitudinal study to collect detailed phenotypic data on a group of young subjects in preparation for studies of therapeutic interventions. Methods Eighteen subjects (ages 5.9–25.8, mean 14.2 years) with genetically confirmed WFS were identified through the Washington University International Wolfram Registry. Examinations included: general medical, neurologic, ophthalmologic, audiologic, vestibular, and urologic exams, cognitive testing and neuroimaging. Results Seventeen (94%) had diabetes mellitus with the average age of diabetes onset of 6.3 ± 3.5 years. Diabetes insipidus was diagnosed in 13 (72%) at an average age of 10.6 ± 3.3 years. Seventeen (94%) had optic disc pallor and defects in color vision, 14 (78%) had hearing loss and 13 (72%) had olfactory defects, eight (44%) had impaired vibration sensation. Enuresis was reported by four (22%) and nocturia by three (17%). Of the 11 tested for bladder emptying, five (45%) had elevated post-void residual bladder volume. Conclusions WFS causes multiple endocrine and neurologic deficits detectable on exam, even early in the course of the disease. Defects in olfaction have been underappreciated. The proposed mechanism of these deficits in WFS is ER stress-induced damage to neuronal and hormone-producing cells. This group of subjects with detailed clinical phenotyping provides a pool for testing proposed treatments for ER stress. Longitudinal follow-up is necessary for establishing the natural history and identifying potential biomarkers of progression. PMID:23981289

Analysis of the Viscoelastic Properties of the Human Cornea Using Scheimpflug Imaging in Inflation Experiment of Eye Globes

PubMed Central

Lombardo, Giuseppe; Serrao, Sebastiano; Rosati, Marianna; Lombardo, Marco

2014-01-01

Purpose To demonstrate a Scheimpflug-based imaging procedure for investigating the depth- and time-dependent strain response of the human cornea to inflation testing of whole eye globes. Methods Six specimens, three of which with intact corneal epithelium, were mounted in a customized apparatus within a humidity and temperature-monitored wet chamber. Each specimen was subjected to two mechanical tests in order to measure corneal strain resulting from application of cyclic (cyclic regimen) and constant (creep regimen) stress by changing the intra-ocular pressure (IOP) within physiological ranges (18–42 mmHg). Corneal shape changes were analyzed as a function of IOP and both corneal stress-strain curves and creep curves were generated. Results The procedure was highly accurate and repeatable. Upon cyclic stress application, a biomechanical corneal elasticity gradient was found in the front-back direction. The average Young's modulus of the anterior cornea ranged between 2.28±0.87 MPa and 3.30±0.90 MPa in specimens with and without intact epithelium (P = 0.05) respectively. The Young's modulus of the posterior cornea was on average 0.21±0.09 MPa and 0.17±0.06 MPa (P>0.05) respectively. The time-dependent strain response of the cornea to creep testing was quantified by fitting data to a modified Zener model for extracting both the relaxation time and compliance function. Conclusion Cyclic and creep mechanical tests are valuable for investigating the strain response of the intact human cornea within physiological IOP ranges, providing meaningful results that can be translated to clinic. The presence of epithelium influences the results of anterior corneal shape changes when monitoring deformation via Scheimpflug imaging in inflation experiments of whole eye globes. PMID:25397674

Effect of silver doping on the elastic properties of CdS nanoparticles

NASA Astrophysics Data System (ADS)

Dey, P. C.; Das, R.

2018-05-01

CdS and Ag doped CdS (CdS/Ag) nanoparticles have been prepared via chemical method from a Cadmium acetate precursor and Thiourea. The synthesized CdS and CdS/Ag nanoparticles have been characterized by the X-ray Diffraction and High Resolution Transmission Electron Microscope. Here, these nanoparticles have been synthesized at room temperature and all the characterization have also been done at room temperature only. The XRD results reveal that the products are crystalline with cubic zinc blende structure. HRTEM images show that the prepared nanoparticles are nearly spherical in shape. Williamson-Hall method and Size-Strain Plot (SSP) have been used to study the individual contribution of crystalline sizes and lattice strain on the peak broadening of the CdS and CdS/Ag nanoparticles. The different modified model of Williamson-Hall method such as, uniform deformation model, uniform stress deformation model and uniform energy density deformation model and SSP method have been used to calculate the different physical parameter such as lattice strain, stress and energy density for all diffraction peaks of the XRD, corresponding to the CdS and silver doped CdS (CdS/Ag). The obtained results reveal that the average particle size of the prepared CdS and CdS/Ag nanoparticles estimated from the HRTEM images, Williamson-Hall analysis and SSP method are highly correlated with each other. Further, all these result confirms that doping of Ag significantly affects the elastic properties of CdS.

Investigation of (Ti-Zr-Hf-V-Nb)N Multicomponent Nanostructured Coatings before and after Thermal Annealing by Nuclear Physics Methods of Analysis

NASA Astrophysics Data System (ADS)

Pogrebnjak, A. D.; Beresnev, V. M.; Bondar', A. V.; Kaverin, M. V.; Ponomarev, A. G.

2013-10-01

(Ti-Zr-Hf-V-Nb)N multicomponent nanostructured coatings with thickness of 1.0-1.4 μm synthesized by the method of cathode arc-vapor deposition at temperatures of 250-300°С are investigated by various mutually complementary methods of elemental structural analysis using slow positron beams (SPB), proton microbeam based particle-induced x-ray emission (μ-PIXE), energy-dispersive x-ray spectroscopy (EDS) and scanning electron microscopy (SEM) analyses based on electron micro- and nanobeams, x-ray diffraction (XRD) method of phase structural analysis, and the "a-sin2φ" method of measuring a stressed-strained state (x-ray tensometry). The elemental composition, microstructure, residual stress in nanograins, profiles of defect and atom distributions with depth and over the coating surface in 3D-representation are studied for these coatings, and their phase composition, severely strained state, and composition of coatings before and after annealing at Tann = 600°С for annealing time τ = 30 min are investigated. It is demonstrated that the oxidation resistance of the examined coatings can be significantly increased by high-temperature annealing that leads to the formation of elastic severely strained compression state of the coating. Redistribution of elements and defects, their segregation near the interface boundaries and around grains and subgrains in the process of thermostimulated diffusion, and termination of spinodal segregation without considerable change of the average nanograin size are revealed.

Developmental Psychopathology in a Racial/Ethnic Minority Group: Are Cultural Risks Relevant?

PubMed Central

Wei, Chiaying; Eisenberg, Ruth E.; Ramos-Olazagasti, María A.; Wall, Melanie; Chen, Chen; Bird, Héctor R.; Canino, Glorisa; Duarte, Cristiane S.

2018-01-01

Objective The current study examined (a) the mediating role of parenting behaviors in the relationship between parental risks and youth antisocial behaviors (YASB), and (b) the role of youth cultural stress in a racial/ethnic minority group (i.e., Puerto Rican [PR] youth). Method This longitudinal study consisted of 3 annual interviews of PR youth (N = 1,150; aged 10–14 years at wave 1) and their caretakers from the South Bronx (SB) in New York City and from San Juan, Puerto Rico. Parents reported on parental risks, parenting behaviors, and YASB. Youth also self-reported on YASB and youth cultural stress. A lagged structural equation model examined the relationship between these variables across 3 yearly waves, with youth cultural stress as a moderator of the association between effective parenting behaviors and YASB. Results Findings supported the positive influence of effective parenting on YASB, independently of past parental risks and past YASB: higher effective parenting significantly predicted lower YASB at the following wave. Parenting also accounted for (mediated) the association between the composite of parental risks and YASB. Youth cultural stress at wave 1 was cross-sectionally associated with higher YASB and moderated the prospective associations between effective parenting and YASB, such that for youth who perceived higher cultural stress, the positive effect of effective parenting on YASB was weakened compared to those with lower/average cultural stress. Conclusion Among PR families, both parental and cultural risk factors influence YASB. Such findings should be considered when treating racial/ethnic minority youth for whom cultural factors may be a relevant influence on determining behaviors. PMID:29173742

Repeated psychological stress-induced alterations of visceral sensitivity and colonic motor functions in mice: influence of surgery and postoperative single housing on visceromotor responses.

PubMed

Larauche, Muriel; Gourcerol, Guillaume; Million, Mulugeta; Adelson, David W; Taché, Yvette

2010-07-01

Visceral pain modulation by chronic stress in mice has been little studied. Electromyography (EMG) recording of abdominal muscle contractions, as a proxy to the visceromotor response (VMR), requires electrode implantation and post-surgical single housing (SH) which could affect the VMR to stress. To test this hypothesis, male mice had electrode implantation surgery (S) plus SH, or no surgery and were group housed (NS-GH) or single housed (NS-SH) and exposed to either water avoidance stress (WAS, 1 h/day) or left undisturbed in their home cages for 10 days. The VMR to phasic ascending colorectal distension (CRD) was assessed before (basal) and 24 h after 10 days of WAS or no stress using a surgery-free method of intraluminal colonic pressure (ICP) recording (solid-state manometry). WAS heightened significantly the VMR to CRD at 30, 45, and 60 mmHg in S-SH vs. NS-GH, but not compared to NS-SH conscious mice. Compared to basal CRD, WAS increased VMR at 60 mmHg in the S-SH group and decreased it at 30-60 mmHg in NS-GH mice, while having no effect in NS-SH mice. The average defecation during the hour of repeated WAS over 10 days was 1.9 and 2.4 fold greater in S-SH vs. NS-GH and NS-SH mice, respectively. These data indicate that the combination of S-SH required for VMR monitoring with EMG is an important component of repeated WAS-induced post-stress visceral hypersensitivity and defecation in mice.

JPRS Report, Near East & South Asia

DTIC Science & Technology

1988-02-08

affairs, and even the promotion of customer favoritism and influence peddling, went on to stress the fundamen- tal objectives of antibureaucratic...and others, this sector has been getting barely 2.1 per cent of DE on an average for the entire period. The study stresses that India has seldom...he also stressed that the region is close to the fall of Kuwait and a humiliating retreat by America from the Persian Gulf. In conclusion, he

Associations between recent gay-related stressful events, emotional distress, social support and unprotected anal intercourse behavior among Chinese men who have sex with men.

PubMed

Yunyong, Liu; Zhe, Wang; Junting, Xu; Yan, Zhou; Xiaoxia, An; Li, Zhao; Yuan, Gu; Chao, Jiang

2016-07-01

This study was designed to assess the levels of and associations between gay-related stressful events, social support, emotional distress and the number of unprotected anal intercourse partners among Chinese men who have sex with men. Using a respondent-driven sampling method, 807 men who have sex with men were recruited in urban areas of northeast China and data were collected via face-to-face interviews. Gay-related stressful events were measured using the Gay-Related Stressful Life Events Scale; levels of depression, anxiety symptoms and social support were measured using the Self-Rating Depression Scale, the Self-Rating Anxiety Scale and the Social Support Rating Scale, respectively. Over a quarter of study participants experienced gay-related stressful events during the preceding 3 months. Their average Self-Rating Depression Scale, Self-Rating Anxiety Scale and Social Support scores differed significantly from the national norm. Gay-related stressful events significantly correlated with anxiety (r = 0.167, p < 0.001), depression (r = 0.165, p < 0.001), social support (r = -0.107, p = 0.002) and number of unprotected anal intercourse partners (r = 0.13, p < 0.001), showing a clear dose-response relationship. Gay-related stressful events are common and are significantly associated with emotional distress, lack of social support and high-risk sexual behaviors among Chinese men who have sex with men. Multifaceted approaches are warranted to increase social support and reduce intolerance toward homosexual behaviors and to reduce risky sexual behaviors related to the rapid HIV epidemic among men who have sex with men population in China. © The Royal Australian and New Zealand College of Psychiatrists 2015.

Phase transformations in nanograin materials under high pressure and plastic shear: nanoscale mechanisms.

PubMed

Levitas, Valery I; Javanbakht, Mahdi

2014-01-07

There are two main challenges in the discovery of new high pressure phases (HPPs) and transforming this discovery into technologies: finding conditions to synthesize new HPPs and finding ways to reduce the phase transformation (PT) pressure to an economically reasonable level. Based on the results of pressure-shear experiments in the rotational diamond anvil cell (RDAC), superposition of plastic shear on high pressure is a promising way to resolve these problems. However, physical mechanisms behind these phenomena are not yet understood. Here, we elucidate generic mechanisms of coupled nucleation and evolution of dislocation and HPP structures in the nanograin material under pressure and shear utilizing the developed advanced phase field approach (PFA). Dislocations are generated at the grain boundaries and are densely piled up near them, creating a strong concentrator of the stress tensor. Averaged shear stress is essentially larger in the nanograin material due to grain boundary strengthening. This leads to the increase in the local thermodynamic driving force for PT, which allows one to significantly reduce the applied pressure. For all cases, the applied pressure is 3-20 times lower than the PT pressure and 2-12.5 times smaller than the phase equilibrium pressure. Interaction between nuclei leads sometimes to their coalescence and growth of the HPP away from stress concentrators. Plasticity plays a dual role: in addition to creating stress concentrators, it may relax stresses at other concentrators, thus competing with PT. Some ways to optimize the loading parameters have been found that lead to methods for controlling PT. Since such a local stress tensor with high shear stress component cannot be created without plastic deformations, this may lead to new transformation paths and phases, which are hidden during pressure induced PTs.

An in vitro investigation of the influence of stenosis severity on the flow in the ascending aorta.

PubMed

Gülan, Utku; Lüthi, Beat; Holzner, Markus; Liberzon, Alex; Tsinober, Arkady; Kinzelbach, Wolfgang

2014-09-01

Cardiovascular diseases can lead to abnormal blood flows, some of which are linked to hemolysis and thrombus formation. Abnormal turbulent flows of blood in the vessels with stenosis create strong shear stresses on blood elements and may cause blood cell destruction or platelet activation. We implemented a Lagrangian (following the fluid elements) measurement technique of three dimensional particle tracking velocimetry that provides insight on the evolution of viscous and turbulent stresses along blood element trajectories. We apply this method to study a pulsatile flow in a compliant phantom of an aorta and compare the results in three cases: the reference case (called "healthy" case), and two cases of abnormal flows due to mild and severe stenosis, respectively. The chosen conditions can mimic a clinical application of an abnormal flow due to a calcific valve. We estimate the effect of aortic stenosis on the kinetic energy of the mean flow and the turbulent kinetic energy, which increases about two orders of magnitude as compared with the healthy flow case. Measuring the total flow stress acting on a moving fluid element that incorporates viscous stresses and the apparent turbulent-induced stresses (the so-called Reynolds stresses) we find out similar increase of the stresses with the increased severity of the stenosis. Furthermore, these unique Lagrangian measurements provide full acceleration and, consequently, the forces acting on the blood elements that are estimated to reach the level that can considerably deform red blood cells. These forces are strong and abrupt due to the contribution of the turbulent fluctuations which is much stronger than the typically measured phase-averaged values. Copyright © 2014 IPEM. Published by Elsevier Ltd. All rights reserved.

Perceived stress correlates with visceral obesity and lipid parameters of the metabolic syndrome: A systematic review and meta-analysis.

PubMed

Tenk, Judit; Mátrai, Péter; Hegyi, Péter; Rostás, Ildikó; Garami, András; Szabó, Imre; Hartmann, Petra; Pétervári, Erika; Czopf, László; Hussain, Alizadeh; Simon, Mária; Szujó, Szabina; Balaskó, Márta

2018-05-12

Perceived stress has been proposed as a risk factor of metabolic syndrome. However, correlations between perceived stress and parameters of the metabolic syndrome have not been properly analyzed despite extensive research data on the topic. Our current meta-analysis aimed to examine the mutual association between perceived stress of patients and parameters of metabolic syndrome. This systematic review has been registered on the PROSPERO database (registration number CRD42017055293). Eligible studies divided participants based on their stress level or on the presence of metabolic syndrome. They reported at least one parameter of the metabolic syndrome or the stress level of the participants measured with some stress scale. Data from 17 articles met the eligibility criteria and were included. Random effects model with the DerSimonian and Laird weighting methods was applied. I-squared indicator and Q test were performed to assess heterogeneity. Although the majority of individual studies failed to demonstrate correlations between stress and their analyzed parameters of metabolic syndrome, our meta-analysis showed a significant association between stress and BMI [average effect size (ES) with 95% confidence interval (95%CI), ES = 0.65, 95%CI 0.16, 1.14), waist circumference (ES = 1.84 cm, 95%CI 0.79, 2.89) and serum triglyceride level (ES = 7.52 mg/dl, 95%CI 0.07, 14.96). Additional analysis confirmed effects of stress on serum HDL (ES = - 1.699 mg/dl, 95%CI -2.966, -0.432) and diastolic blood pressure (ES = 1.04 mmHg, 95%CI 0.18, 1.89). No correlations were found for fasting glucose or systolic blood pressure. No association between metabolic syndrome and stress level of patients was detected either. The potentially key role of visceral obesity in the association between perceived stress and dyslipidemia or diastolic blood pressure are discussed together with potential moderators (e.g. gender-differences, variations in stress assessment and metabolic syndrome criteria) that may explain the inconsistent, contradictory results of the individual studies. Copyright © 2018 Elsevier Ltd. All rights reserved.

Clinical experimental stress studies: methods and assessment.

PubMed

Bali, Anjana; Jaggi, Amteshwar Singh

2015-01-01

Stress is a state of threatened homeostasis during which a variety of adaptive processes are activated to produce physiological and behavioral changes. Stress induction methods are pivotal for understanding these physiological or pathophysiological changes in the body in response to stress. Furthermore, these methods are also important for the development of novel pharmacological agents for stress management. The well-described methods to induce stress in humans include the cold pressor test, Trier Social Stress Test, Montreal Imaging Stress Task, Maastricht Acute Stress Test, CO2 challenge test, Stroop test, Paced Auditory Serial Addition Task, noise stress, and Mannheim Multicomponent Stress Test. Stress assessment in humans is done by measuring biochemical markers such as cortisol, cortisol awakening response, dexamethasone suppression test, salivary α-amylase, plasma/urinary norepinephrine, norepinephrine spillover rate, and interleukins. Physiological and behavioral changes such as galvanic skin response, heart rate variability, pupil size, and muscle and/or skin sympathetic nerve activity (microneurography) and cardiovascular parameters such as heart rate, blood pressure, and self-reported anxiety are also monitored to assess stress response. This present review describes these commonly employed methods to induce stress in humans along with stress assessment methods.

Triggered reverse fault and earthquake due to crustal unloading, northwest Transverse Ranges, California.

USGS Publications Warehouse

Yerkes, R.F.; Ellsworth, W.L.; Tinsley, J.C.

1983-01-01

A reverse-right-oblique surface rupture, associated with a ML 2.5 earthquake, formed in a diatomite quarry near Lompoc, California, in the northwesternmost Transverse Ranges on April 7, 1981. The 575-m-long narrow zone of ruptures formed in clay interbeds in diatomite and diatomaceous shale of the Neogene Monterey Formation. The ruptures parallel bedding, dip 39o-59oS, and trend about N84oE on the north limb of an open symmetrical syncline. Maximum net slip was 25 cm; maximum reverse dip slip was 23 cm, maximum right-lateral strike slip was about 9 cm, and average net slip was about 12 cm. The seismic moment of the earthquake is estimated at 1 to 2 X 1018 dyne/cm and the static stress drop at about 3 bar. The removal of an average of about 44 m of diatomite resulted in an average load reduction of about 5 bar, which decreased the normal stress by about 3.5 bar and increased the shear stress on the tilted bedding plane by about 2 bar. The April 7, 1981, event was a very shallow bedding-plane rupture, apparently triggered by crustal unloading. -Authors

HPC simulations of shock front evolution for a study of the shock precursor decay in a submicron thick nanocrystalline aluminum

NASA Astrophysics Data System (ADS)

Valisetty, R.; Rajendran, A.; Agarwal, G.; Dongare, A.; Ianni, J.; Namburu, R.

2018-07-01

The Hugoniot elastic limit (HEL, or the shock precursor) decay phenomenon was investigated under an uniaxial strain condition, in a plate-on-plate impact configuration, using large-scale molecular dynamics (MD) high performance computing (HPC) simulations on a multi-billion 5000 Å thick nanocrystalline aluminum (nc-Al) system with an average grain size of 1000 Å and at five impact velocities ranging from 0.7 to 1.5 km s‑1. The averaged stress and strain distributions were obtained in the shock fronts’ travel direction using a material conserving atom slicing method. The loading paths in terms of the Rayleigh lines experienced by the atom system in the evolving shock fronts exhibited a strong dependency on the shock stress levels. This dependency decreased as the impact velocity increased from 0.7 to 1.5 km s‑1. By combining the HELs from MD results with plate impact experimental data, the precursor decay for the nc-Al was predicted from nano-to-macro scale thickness range. The evolving shock fronts were characterized in terms of parameters such as the shock front thickness, shock rise time and strain rate. The MD results were further analyzed using a crystal analysis algorithm and a twin dislocation identification method to obtain the densities of the atomistic defects evolving behind the evolving shock fronts. High-fidelity large-scale HPC simulation results showed that certain dislocation partials strongly influenced the elastic–plastic transition response across the HELs. The twinning dislocations increased by more than a factor of 10 during the transition and remained constant under further shock compression.

Noninvasive quantification of myocardial blood flow in humans. A direct comparison of the [13N]ammonia and the [15O]water techniques.

PubMed

Nitzsche, E U; Choi, Y; Czernin, J; Hoh, C K; Huang, S C; Schelbert, H R

1996-06-01

[13N]Ammonia has been validated in dog studies as a myocardial blood flow tracer. Estimates of myocardial blood flow by [13N]ammonia were highly linearly correlated to those by the microsphere and blood sample techniques. However, estimates of myocardial blood flow with [13N]ammonia in humans have not yet been compared with those by an independent technique. This study therefore tested the hypothesis that the [13N]ammonia positron emission tomographic technique in humans gives estimates of myocardial blood flow comparable to those obtained with the [15O]water technique. A total of 30 pairs of positron emission tomographic flow measurements were performed in 30 healthy volunteers; 15 volunteers were studied at rest and 15 during adenosine-induced hypermia. Estimates of average and of regional myocardial blood flow by the [13N]ammonia and the [15O]water approaches correlated well (y = 0.02 + 1.02x, r = .99, P < .001 SEE = 0.023 for average and y = 0.06 + 1.00x, r = .97, P < .001, SEE = 0.025 for regional values) over a flow range of 0.45 to 4.74 mL.min-1.g-1. At rest, mean myocardial blood flow was 0.64 +/- 0.09 mL.min-1.g-1 for [13N]ammonia and 0.66 +/- 0.12 mL.min-1.g-1 for [15O]water (P = NS). For adenosine-induced hyperemia, mean myocardial blood flow was 2.63 +/- 0.75 mL.min-1.g-1 for [13N]ammonia and 2.73 +/- 0.77 mL.min-1.g-1 for [15O]water (P = NS). The coefficient of variation as an index of the observed heterogeneity of myocardial blood flow averaged, for [13N]ammonia, 9 +/- 4% at rest and 12 +/- 7% during stress and, for [15O]water, 14 +/- 11% at rest and 16 +/- 9% during stress. The coefficients of variation for [15O]water were significantly higher than those for [13N]ammonia (P = .004 at rest and P = .03 during stress). The two approaches yield comparable estimates of myocardial blood flow in humans, which supports the validity of the [13N]ammonia method in human myocardium previously shown only in animals. However, the [15O]water approach reveals a greater heterogeneity (presumably method-related), which might limit the accuracy of sectorial myocardial blood flow estimates in humans.

Flow field and oscillatory shear stress in a tuning-fork-shaped model of the average human carotid bifurcation.

PubMed

Ding, Z; Wang, K; Li, J; Cong, X

2001-12-01

The oscillatory shear index (OSI) was developed based on the hypothesis that intimal hyperplasia was correlated with oscillatory shear stresses. However, the validity of the OSI was in question since the correlation between intimal thickness and the OSI at the side walls of the sinus in the Y-shaped model of the average human carotid bifurcation (Y-AHCB) was weak. The objectives of this paper are to examine whether the reason for the weak correlation lies in the deviation in geometry of Y-AHCB from real human carotid bifurcation, and whether this correlation is clearly improved in the tuning-fork-shaped model of the average human carotid bifurcation (TF-AHCB). The geometry of the TF-AHCB model was based on observation and statistical analysis of specimens from 74 cadavers. The flow fields in both models were studied and compared by using flow visualization methods under steady flow conditions and by using laser Doppler anemometer (LDA) under pulsatile flow conditions. The TF-shaped geometry leads to a more complex flow field than the Y-shaped geometry. This added complexity includes strengthened helical movements in the sinus, new flow separation zone, and directional changes in the secondary flow patterns. The results show that the OSI-values at the side walls of the sinus in the TF-shaped model were more than two times as large as those in the Y-shaped model. This study confirmed the stronger correlation between the OSI and intimal thickness in the tuning-fork geometry of human carotid bifurcation, and the TF-AHCB model is a significant improvement over the traditional Y-shaped model.

Low Socioeconomic Status Negatively Affects Sleep in Pregnant Women

PubMed Central

Okun, Michele L.; Tolge, Madeline; Hall, Martica

2014-01-01

Objective To evaluate the effect of socioeconomic status on measures of sleep quality, continuity, and quantity in a large cohort of pregnant women. Design Prospective, longitudinal study. Participants One hundred seventy (170) pregnant women at 10-20 weeks gestation. Methods Sleep quality was assessed with the Pittsburgh Sleep Quality Index. Sleep duration and continuity (sleep fragmentation index [SFI]) were assessed with actigraphy at 10-12, 14-16, and 18-20 weeks gestation. Since sleep did not significantly differ across time, averages across all three time points were used in analyses. Socioeconomic status (SES) was defined by self-reported annual household income. Linear regression analyses were used to model the independent associations of SES on sleep after adjusting for age, race, parity, marital status, body mass index (BMI), perceived stress, depressive symptoms, and financial strain. Results On average, women reported modestly poor sleep quality (M = 5.4, SD= 2.7), short sleep duration (391 (55.6) min) and fragmented sleep (SFI M = 33.9, SD= 10.4. A household income < $50,000/year was associated with poorer sleep quality (β = -.18, p < .05) and greater sleep fragmentation (β= -.18, p < .05) following covariate adjustment. Conclusions Low SES was associated with poorer sleep quality and fragmented sleep, even after statistical adjustments. Perceived stress and financial strain attenuated SES-sleep associations indicating that psychosocial situations preceding pregnancy are also important to consider. PMID:24617761

Fabrication of mandible fracture plate by indirect additive manufacturing

NASA Astrophysics Data System (ADS)

Aizat, M.; Khan, S. F.

2017-10-01

Bone fracture is a serious skeletal injury due to accidents and fragility of the bones at a certain age. In order to accelerate fracture healing process, fracture bone plate is use to hold the fracture segment for more stability. The purpose of this study is to fabricate mandibular fracture plate by using indirect additive manufacturing methods in order to reduce time taken during bending and shaping the fracture fixation plate that conform to the anatomy of the fractured bone site. The design and analysis of the plates are performed using CATIA and ANSYS software. The 3D-CAD data were sent to an additive manufacturing machine (fused filament fabricated) to generate master pattern using PLA and the mould were fabricated using Plaster of Paris. A melt ZAMAK 3 was poured directly into the moulds, and left it until completely harden. 3point bending test was performed on the prototype plate using universal testing machine. Stress-strain curve shows the graph exhibited a linear relationship of stress-strain up to a strain value of 0.001. Specimens give a maximum yielding stress and then break before the conventional deflection. Since the maximum flexural stress and the breaking stress are far apart with a plateau stating at strain value of 0.003mm/mm in most specimens, the specimen’s failure types are considered plastic failure mode. The average thickness and width are 1.65mm and 2.18mm respectively. The flexural modulus and flexural strength are 189.5GPa and 518.1MPa, respectively.

Salivary alpha-amylase, secretory IgA and free cortisol as neurobiological components of the stress response in the acute phase of anorexia nervosa.

PubMed

Paszynska, E; Dmitrzak-Weglarz, M; Tyszkiewicz-Nwafor, M; Slopien, A

2016-06-01

Objectives One novel hypothesis of the pathogenesis of anorexia nervosa (AN) is the possible role of mental stress in hyperactivity of the autonomic nervous system (ANS) and of the hypothalamic-pituitary-adrenal (HPA) axis. Two components of stress response - salivary alpha-amylase (sAA) and free cortisol - have been proposed. They can be determined in saliva, which closely reflects their concentrations in plasma. The purpose of this study was to measure salivary free cortisol, sAA and their correlation to secretory IgA (sIgA) of patients with AN in comparison to the average population. Methods A controlled clinical trial was designed for a matched group of 47 AN patients and 54 healthy individuals. After clinical examination, unstimulated salivary samples were taken during the acute stage of AN (BMI < 15 kg/m(2)) in the first week of hospitalisation. An enzyme-linked immunosorbent assay (ELISA) suitable for measuring sAA, sIgA and free cortisol were used. Results Anorexic patients exhibited disturbances in sAA secretion, and significantly increased cortisol and sIgA levels with a distinct correlation between these two parameters. Conclusions The behaviour of cortisol, sAA and sIgA levels can be assessed as an effect of stress reaction among AN patients with hyperactivity of the HPA axis and ANS dysregulation. The effect of stress response can be assessed reliably in saliva.