Design, fabrication, and operation of dished accelerator grids on a 30-cm ion thruster

NASA Technical Reports Server (NTRS)

Rawlin, V. K.; Banks, B. A.; Byers, D. C.

1972-01-01

Several closely-space dished accelerator grid systems were fabricated and tested on a 30-cm diameter mercury bombardment thruster and they appear to be a solution to the stringent requirements imposed by the near-term, high-thrust, low specific impulse electric propulsion missions. The grids were simultaneously hydroformed and then simultaneously stress relieved. The ion extraction capability and discharge chamber performance were studied as the total accelerating voltage, the ratio of net-to-total voltage, grid spacing, and dish direction were varied.

Advanced Antenna Design for NASA's EcoSAR Instrument

NASA Technical Reports Server (NTRS)

Du Toit, Cornelis F.; Deshpande, Manohar; Rincon, Rafael F.

2016-01-01

Advanced antenna arrays were designed for NASA's EcoSAR airborne radar instrument. EcoSAR is a beamforming synthetic aperture radar instrument designed to make polarimetric and "single pass" interferometric measurements of Earth surface parameters. EcoSAR's operational requirements of a 435MHz center frequency with up to 200MHz bandwidth, dual polarization, high cross-polarization isolation (> 30 dB), +/- 45deg beam scan range and antenna form-factor constraints imposed stringent requirements on the antenna design. The EcoSAR project successfully developed, characterized, and tested two array antennas in an anechoic chamber. EcoSAR's first airborne campaign conducted in the spring of 2014 generated rich data sets of scientific and engineering value, demonstrating the successful operation of the antennas.

Converged Infrastructure for Emerging Regions - A Research Agenda

NASA Astrophysics Data System (ADS)

Chevrollier, Nicolas; Zidbeck, Juha; Ntlatlapa, Ntsibane; Simsek, Burak; Marikar, Achim

In remote parts of Africa, the lack of energy supply, of wired infrastructure, of trained personnel and the limitation in OPEX and CAPEX impose stringent requirements on the network building blocks that support the communication infrastructure. Consequently, in this promising but untapped market, the research aims at designing and implementing energy-efficient, robust, reliable and affordable wide heterogeneous wireless mesh networks to connect geographically very large areas in a challenged environment. This paper proposes a solution that is aimed at enhancing the usability of Internet services in the harsh target environment and especially how the end-users experience the reliability of these services.

Principles of gas phase processing of ceramics during combustion

NASA Technical Reports Server (NTRS)

Zachariah, Michael R.

1993-01-01

In recent years, ceramic materials have found applications in an increasingly wider range of industrial processes, where their unique mechanical, electrical and optical properties are exploited. Ceramics are especially useful for applications in high temperature, corrosive environments, which impose particularly stringent requirements on mechanical reliability. One approach to provide such materials is the manufacture of submicron (and more recently nanometer scale) particles, which may subsequently be sintered to produce a material with extremely high mechanical integrity. However, high quality ceramic materials can only be obtained if particles of known size, polydispersity, shape and chemical purity can be produced consistently, under well controlled conditions. These requirements are the fundamental driving force for the renewed interest in studying particle formation and growth of such materials.

Anomalously high potentials observed on ISEE

NASA Technical Reports Server (NTRS)

Whipple, E. C.; Krinsky, I. S.; Torbert, R. B.; Olsen, R. C.

1985-01-01

Data from two electric field experiments and from the plasma composition experiment on ISEE-1 are used to show that the spacecraft charged to close to -70 V in sunlight at 0700 UT on March 17, 1978. Data from the electron spectrometer experiment show that there was a potential barrier of -10 to -20 V about the spacecraft during this event. The potential barrier was effective in turning back emitted photoelectrons to the spacecraft. The stringent electrostatic cleanliness specifications imposed on ISEE make the presence of differential charging unlikely. Modeling of this event is required to determine if the barrier was produced by the presence of space charge.

A privacy challenge to longitudinal study methods: patient-derived codes.

PubMed

Clay, Fiona J; Ozanne-Smith, Joan; Watson, Wendy; Congiu, Melinda; Fox, Barbara

2006-08-01

Recent changes to privacy legislation in Australia have resulted in more stringent requirements with respect to maintaining the confidentiality of patient health information. We describe a method employed to de-identify health information collected in a longitudinal study using codes. Using a patient-derived code that did not change during the life of the study follow-up resulted in errors in a quarter of the follow-up surveys. This may introduce bias that could compromise the validity of the study. Alternative methods of coding may alleviate some of these issues. However, removal of some of the constraints imposed by interpretations of privacy legislation may be the best way forward.

A spacecraft integrated power/attitude control system

NASA Technical Reports Server (NTRS)

Keckler, C. R.; Jacobs, K. L.

1974-01-01

A study to determine the viability and application of a system capable of performing the dual function of power storage/generation and attitude control has been conducted. Results from the study indicate that an integrated power/attitude control system (IPACS) can satisfy future mission requirements while providing significant savings in weight, volume, and cost over conventional systems. A failure-mode configuration of an IPACS was applied to a shuttle-launched RAM free-flyer and simulated using make-do hardware linked to a hybrid computer. Data from the simulation runs indicate that control interactions resulting from heavy power demands have minimal effect on system control effectiveness. The system was shown to be capable of meeting the stringent pointing requirements of 1 arc-second while operating under the influence of an orbital disturbance environment and during periods of momentum variations imposed by energy transfer requirements.

NASA's Solar Dynamics Observatory (SDO): A Systems Approach to a Complex Mission

NASA Technical Reports Server (NTRS)

Ruffa, John A.; Ward, David K.; Bartusek, LIsa M.; Bay, Michael; Gonzales, Peter J.; Pesnell, William D.

2012-01-01

The Solar Dynamics Observatory (SDO) includes three advanced instruments, massive science data volume, stringent science data completeness requirements, and a custom ground station to meet mission demands. The strict instrument science requirements imposed a number of challenging drivers on the overall mission system design, leading the SDO team to adopt an integrated systems engineering presence across all aspects of the mission to ensure that mission science requirements would be met. Key strategies were devised to address these system level drivers and mitigate identified threats to mission success. The global systems engineering team approach ensured that key drivers and risk areas were rigorously addressed through all phases of the mission, leading to the successful SDO launch and on-orbit operation. Since launch, SDO's on-orbit performance has met all mission science requirements and enabled groundbreaking science observations, expanding our understanding of the Sun and its dynamic processes.

NASA's Solar Dynamics Observatory (SDO): A Systems Approach to a Complex Mission

NASA Technical Reports Server (NTRS)

Ruffa, John A.; Ward, David K.; Bartusek, Lisa M.; Bay, Michael; Gonzales, Peter J.; Pesnell, William D.

2012-01-01

The Solar Dynamics Observatory (SDO) includes three advanced instruments, massive science data volume, stringent science data completeness requirements, and a custom ground station to meet mission demands. The strict instrument science requirements imposed a number of challenging drivers on the overall mission system design, leading the SDO team to adopt an integrated systems engineering presence across all aspects of the mission to ensure that mission science requirements would be met. Key strategies were devised to address these system level drivers and mitigate identified threats to mission success. The global systems engineering team approach ensured that key drivers and risk areas were rigorously addressed through all phases of the mission, leading to the successful SDO launch and on-orbit operation. Since launch, SDO s on-orbit performance has met all mission science requirements and enabled groundbreaking science observations, expanding our understanding of the Sun and its dynamic processes.

State Law Approaches to Facility Regulation of Abortion and Other Office Interventions

PubMed Central

Daniel, Sara; Cloud, Lindsay K.

2018-01-01

Objectives. To compare the prevalence and characteristics of facility laws governing abortion provision specifically (targeted regulation of abortion providers [TRAP] laws); office-based surgeries, procedures, sedation or anesthesia (office interventions) generally (OBS laws); and other procedures specifically. Methods. We conducted cross-sectional legal assessments of state facility laws for office interventions in effect as of August 1, 2016. We coded characteristics for each law and compared characteristics across categories of laws. Results. TRAP laws (n = 55; in 34 states) were more prevalent than OBS laws (n = 25; in 25 states) or laws targeting other procedures (n = 1; in 1 state). TRAP laws often regulated facilities that would not be regulated under OBS laws (e.g., all TRAP laws, but only 2 OBS laws, applied regardless of sedation or anesthesia used). TRAP laws imposed more numerous and more stringent requirements than OBS laws. Conclusions. Many states regulate abortion-providing facilities differently, and more stringently, than facilities providing other office interventions. The Supreme Court’s 2016 decision in Whole Woman’s Health v Hellerstedt casts doubt on the legitimacy of that differential treatment. PMID:29470114

Investigating Allegations of Inappropriate Physical Punishment of Students by School Employees.

ERIC Educational Resources Information Center

Pearce, Alexis C.

1992-01-01

Any complaint against a school employee regarding inappropriate physical punishment should be taken seriously by administrators and pursued vigorously by an investigating attorney. The standards (especially regarding probable cause and obtaining warrants) for investigating such allegations are less stringent than those imposed in criminal…

Canceling the Gravity Gradient Phase Shift in Atom Interferometry.

PubMed

D'Amico, G; Rosi, G; Zhan, S; Cacciapuoti, L; Fattori, M; Tino, G M

2017-12-22

Gravity gradients represent a major obstacle in high-precision measurements by atom interferometry. Controlling their effects to the required stability and accuracy imposes very stringent requirements on the relative positioning of freely falling atomic clouds, as in the case of precise tests of Einstein's equivalence principle. We demonstrate a new method to exactly compensate the effects introduced by gravity gradients in a Raman-pulse atom interferometer. By shifting the frequency of the Raman lasers during the central π pulse, it is possible to cancel the initial position- and velocity-dependent phase shift produced by gravity gradients. We apply this technique to simultaneous interferometers positioned along the vertical direction and demonstrate a new method for measuring local gravity gradients that does not require precise knowledge of the relative position between the atomic clouds. Based on this method, we also propose an improved scheme to determine the Newtonian gravitational constant G towards the 10 ppm relative uncertainty.

Canceling the Gravity Gradient Phase Shift in Atom Interferometry

NASA Astrophysics Data System (ADS)

D'Amico, G.; Rosi, G.; Zhan, S.; Cacciapuoti, L.; Fattori, M.; Tino, G. M.

2017-12-01

Gravity gradients represent a major obstacle in high-precision measurements by atom interferometry. Controlling their effects to the required stability and accuracy imposes very stringent requirements on the relative positioning of freely falling atomic clouds, as in the case of precise tests of Einstein's equivalence principle. We demonstrate a new method to exactly compensate the effects introduced by gravity gradients in a Raman-pulse atom interferometer. By shifting the frequency of the Raman lasers during the central π pulse, it is possible to cancel the initial position- and velocity-dependent phase shift produced by gravity gradients. We apply this technique to simultaneous interferometers positioned along the vertical direction and demonstrate a new method for measuring local gravity gradients that does not require precise knowledge of the relative position between the atomic clouds. Based on this method, we also propose an improved scheme to determine the Newtonian gravitational constant G towards the 10 ppm relative uncertainty.

41 CFR 302-16.2 - What are miscellaneous expenses?

Code of Federal Regulations, 2012 CFR

2012-07-01

... relocating that are not covered by other relocation benefits detailed in Chapter 302. (b) Expenses allowable... use taxes imposed when bringing vehicles into certain jurisdictions Transportation of pets The only... other house pets, as well as costs due to stringent air carrier rules. Other animals (horses, fish...

41 CFR 302-16.2 - What are miscellaneous expenses?

Code of Federal Regulations, 2014 CFR

2014-07-01

... relocating that are not covered by other relocation benefits detailed in chapter 302. (b) Expenses allowable... use taxes imposed when bringing vehicles into certain jurisdictions Transportation of pets The only... other house pets, as well as costs due to stringent air carrier rules. Other animals (horses, fish...

41 CFR 302-16.2 - What are miscellaneous expenses?

Code of Federal Regulations, 2013 CFR

2013-07-01

... relocating that are not covered by other relocation benefits detailed in Chapter 302. (b) Expenses allowable... use taxes imposed when bringing vehicles into certain jurisdictions Transportation of pets The only... other house pets, as well as costs due to stringent air carrier rules. Other animals (horses, fish...

System Identification for Nonlinear Control Using Neural Networks

NASA Technical Reports Server (NTRS)

Stengel, Robert F.; Linse, Dennis J.

1990-01-01

An approach to incorporating artificial neural networks in nonlinear, adaptive control systems is described. The controller contains three principal elements: a nonlinear inverse dynamic control law whose coefficients depend on a comprehensive model of the plant, a neural network that models system dynamics, and a state estimator whose outputs drive the control law and train the neural network. Attention is focused on the system identification task, which combines an extended Kalman filter with generalized spline function approximation. Continual learning is possible during normal operation, without taking the system off line for specialized training. Nonlinear inverse dynamic control requires smooth derivatives as well as function estimates, imposing stringent goals on the approximating technique.

The Space Station Prototype Program - The development of a regenerative life support system for extended-duration missions.

NASA Technical Reports Server (NTRS)

Willis, N. C., Jr.; Neel, J. M.

1972-01-01

Design concepts and test philosophies which may contribute to the development of a low-cost maintainable environmental control/life support system are examined. It is shown that the concept of producing flight prototype equipment during a developmental program can reduce the eventual cost of a flight system by incorporating realistic flight-type design requirements without imposing exacting design features and stringent controls. A flight prototype design is one that can be converted readily into an actual flight design without any conceptual change. Modularity of subsystems provides the system and the program a degree of flexibility relative to the eventual vehicle configuration and technological improvements.

The LLRF System for the S-Band RF Plants of the FERMI Linac

NASA Astrophysics Data System (ADS)

Fabris, A.; Byrd, J.; D'Auria, G.; Doolittle, L.; Gelmetti, F.; Huang, G.; Jones, J.; Milloch, M.; Predonzani, M.; Ratti, A.; Rohlev, T.; Salom, A.; Serrano, C.; Stettler, M.

2016-04-01

Specifications on electron beam quality for the operation of a linac-based free-electron laser (FEL), as FERMI in Trieste (Italy), impose stringent requirements on the stability of the electromagnetic fields of the accelerating sections. These specifications can be met only with state-of-the-art low-level RF (LLRF) systems based on advanced digital technologies. Design considerations, construction, and performance results of the FERMI digital LLRF are presented in this paper. The stability requirements derived by simulations are better than 0.1% in amplitude and 0.1° S-band in phase. The system installed in the FERMI Linac S-band RF plants has met these specifications and is in operation on a 24-h basis as a user facility. Capabilities of the system allow planning for new developments that are also described here.

Design and Evaluation of a Virtual Environment Infrastructure to Support Experiments in Social Behavior

ERIC Educational Resources Information Center

Hmeljak, Dimitrij

2010-01-01

Virtual worlds provide useful platforms for social behavioral research, but impose stringent limitations on the rules of engagement, responsiveness, and data collection, along with other resource restrictions. The major challenge from a computer science standpoint in developing group behavior applications for such environments is accommodating the…

Development and Sizing of the JWST Integrated Science Instrument Module (ISIM) Metering Structure

NASA Technical Reports Server (NTRS)

Johnston, John; Kunt, Cengiz; Bartoszyk, Andrew; Hendricks, Steve; Cofie, Emmanuel

2006-01-01

The JWST Integrated Science Instrument Module (ISIM) includes a large metering structure (approx. 2m x 2m x 1.5m) that houses the science instruments and guider. Stringent dimensional stability and repeatability requirements combined with mass limitations led to the selection of a composite bonded frame design comprised of biased laminate tubes. Even with the superb material specific stiffness, achieving the required frequency for the given mass allocations in conjunction with severe spatial limitations imposed by the instrument complement has proven challenging. In response to the challenge, the ISIM structure team considered literally over 100 primary structure topology and kinematic mount configurations, and settled on a concept comprised of over 70 m of tubes, over 50 bonded joint assemblies, and a "split bi-pod" kinematic mount configuration. In this paper, we review the evolution of the ISIM primary structure topology and kinematic mount configuration to the current baseline concept.

Navigation of space VLBI missions: Radioastron and VSOP

NASA Technical Reports Server (NTRS)

Ellis, Jordan

1993-01-01

In the mid-1990s, Russian and Japanese space agencies will each place into highly elliptic earth orbit a radio telescope consisting of a large antenna and radio astronomy receivers. Very long baseline interferometry (VLBI) techniques will be used to obtain high resolution images of radio sources observed by the space and ground based antennas. Stringent navigation accuracy requirements are imposed on the space VLBI missions by the need to transfer an ultra-stable ground reference frequency standard to the spacecraft and by the demands of the VLBI correlation process. Orbit determination for the mission will be the joint responsibility of navigation centers in the U.S., Russia, and Japan with orbit estimates based on combining tracking data from NASA, Russian, and Japanese sites. This paper describes the operational plans, the inter-agency coordination, and data exchange between the navigation centers required for space VLBI navigation.

Cosmology based on f(R) gravity admits 1 eV sterile neutrinos.

PubMed

Motohashi, Hayato; Starobinsky, Alexei A; Yokoyama, Jun'ichi

2013-03-22

It is shown that the tension between recent neutrino oscillation experiments, favoring sterile neutrinos with masses of the order of 1 eV, and cosmological data which impose stringent constraints on neutrino masses from the free streaming suppression of density fluctuations, can be resolved in models of the present accelerated expansion of the Universe based on f(R) gravity.

The Elephant in the Room: School Districts Nationwide Are Voluntarily Filtering the Filters--And No One Is Talking about It

ERIC Educational Resources Information Center

Bell, Mary Ann

2007-01-01

In this article, the author expresses her disappointment over the self-censorship being practiced by some schools. Some schools are only letting students search sites on district-approved lists, while others are imposing stringent time limits on certain sites. In a few extreme cases, schools banned Internet entirely. These practices are blocking…

Dummy and injury criteria for aircraft crashworthiness.

DOT National Transportation Integrated Search

1996-04-01

Since 1988, newly type-certificated aircraft are required to comply with stringent crashworthiness requirements. Central to these more stringent requirements is a dynamic test that assesses the potential for injury for someone exposed to similar cond...

The fragility of freedom of speech.

PubMed

Shackel, Nicholas

2013-05-01

Freedom of speech is a fundamental liberty that imposes a stringent duty of tolerance. Tolerance is limited by direct incitements to violence. False notions and bad laws on speech have obscured our view of this freedom. Hence, perhaps, the self-righteous intolerance, incitements and threats in response to Giubilini and Minerva. Those who disagree have the right to argue back but their attempts to shut us up are morally wrong.

Flight Mechanics of the Entry, Descent and Landing of the ExoMars Mission

NASA Technical Reports Server (NTRS)

HayaRamos, Rodrigo; Boneti, Davide

2007-01-01

ExoMars is ESA's current mission to planet Mars. A high mobility rover and a fixed station will be deployed on the surface of Mars. This paper regards the flight mechanics of the Entry, Descent and Landing (EDL) phases used for the mission analysis and design of the Baseline and back-up scenarios of the mission. The EDL concept is based on a ballistic entry, followed by a descent under parachutes and inflatable devices (airbags) for landing. The mission analysis and design is driven by the flexibility in terms of landing site, arrival dates and the very stringent requirement in terms of landing accuracy. The challenging requirements currently imposed to the mission need innovative analysis and design techniques to support system design trade-offs to cope with the variability in entry conditions. The concept of the Global Entry Corridor has been conceived, designed, implemented and successfully validated as a key tool to provide a global picture of the mission capabilities in terms of landing site reachability.

Earth's field NMR detection of oil under arctic ice-water suppression

NASA Astrophysics Data System (ADS)

Conradi, Mark S.; Altobelli, Stephen A.; Sowko, Nicholas J.; Conradi, Susan H.; Fukushima, Eiichi

2018-03-01

Earth's field NMR has been developed to detect oil trapped under or in Arctic sea-ice. A large challenge, addressed here, is the suppression of the water signal that dominates the oil signal. Selective suppression of water is based on relaxation time T1 because of the negligible chemical shifts in the weak earth's magnetic field, making all proton signals overlap spectroscopically. The first approach is inversion-null recovery, modified for use with pre-polarization. The requirements for efficient inversion over a wide range of B1 and subsequent adiabatic reorientation of the magnetization to align with the static field are stressed. The second method acquires FIDs at two durations of pre-polarization and cancels the water component of the signal after the data are acquired. While less elegant, this technique imposes no stringent requirements. Similar water suppression is found in simulations for the two methods. Oil detection in the presence of water is demonstrated experimentally with both techniques.

Earth's field NMR detection of oil under arctic ice-water suppression.

PubMed

Conradi, Mark S; Altobelli, Stephen A; Sowko, Nicholas J; Conradi, Susan H; Fukushima, Eiichi

2018-03-01

Earth's field NMR has been developed to detect oil trapped under or in Arctic sea-ice. A large challenge, addressed here, is the suppression of the water signal that dominates the oil signal. Selective suppression of water is based on relaxation time T 1 because of the negligible chemical shifts in the weak earth's magnetic field, making all proton signals overlap spectroscopically. The first approach is inversion-null recovery, modified for use with pre-polarization. The requirements for efficient inversion over a wide range of B 1 and subsequent adiabatic reorientation of the magnetization to align with the static field are stressed. The second method acquires FIDs at two durations of pre-polarization and cancels the water component of the signal after the data are acquired. While less elegant, this technique imposes no stringent requirements. Similar water suppression is found in simulations for the two methods. Oil detection in the presence of water is demonstrated experimentally with both techniques. Copyright © 2018 Elsevier Inc. All rights reserved.

Characterization of three-way automotive catalysts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kenik, E.A.; More, K.L.; LaBarge, W.

1997-04-01

The CRADA between Delphi Automotive Systems (Delphi; formerly General Motors - AC Delco, Systems) and Lockheed Martin Energy Research (LMER) on automotive catalysts was completed at the end of FY96, after a ten month, no-cost extension. The CRADA was aimed at improved performance and lifetime of noble metal based three-way-catalysts (TWC), which are the primary catalytic system for automotive emission control systems. While these TWC can meet the currently required emission standards, higher than optimum noble metal loadings are often required to meet lifetime requirements. In addition, more stringent emission standards will be imposed in the near future, demanding improvedmore » performance and service life from these catalysts. Understanding the changes of TWC conversion efficiency with ageing is a critical need in improving these catalysts. Initially in a fresh catalyst, the active material is often distributed on a very fine scale, approaching single atoms or small atomic clusters. As such, a wide range of analytical techniques have been employed to provide high spatial resolution characterization of the evolving state of the catalytic material.« less

Water and health.

PubMed

Guidotti, T L; Conway, J B

1984-10-01

The systems protecting the quality of drinking water in the United States are deteriorating. Many urban water and sewer systems are obsolete. Industrial wastes are imposing a burden on wastewater treatment facilities. In the U.S., outbreaks of water-borne disease are primarily limited to enteritis associated with viruses or Giardia. Issues in the contamination of drinking water by toxic substances include disposal practices, accidental contamination, agricultural runoff and chlorination byproducts. Physicians must support stringent enforcement of water quality standards.

40 CFR 503.5 - Additional or more stringent requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements. 503.5 Section 503.5 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SEWAGE SLUDGE STANDARDS FOR THE USE OR DISPOSAL OF SEWAGE SLUDGE General Provisions § 503.5 Additional or more... the use or disposal of sewage sludge in addition to or more stringent than the requirements in this...

Robust frequency stabilization of multiple spectroscopy lasers with large and tunable offset frequencies.

PubMed

Nevsky, A; Alighanbari, S; Chen, Q-F; Ernsting, I; Vasilyev, S; Schiller, S; Barwood, G; Gill, P; Poli, N; Tino, G M

2013-11-15

We have demonstrated a compact, robust device for simultaneous absolute frequency stabilization of three diode lasers whose carrier frequencies can be chosen freely relative to the reference. A rigid ULE multicavity block is employed, and, for each laser, the sideband locking technique is applied. A small lock error, computer control of frequency offset, wide range of frequency offset, simple construction, and robust operation are the useful features of the system. One concrete application is as a stabilization unit for the cooling and trapping lasers of a neutral-atom lattice clock. The device significantly supports and improves the clock's operation. The laser with the most stringent requirements imposed by this application is stabilized to a line width of 70 Hz, and a residual frequency drift less than 0.5 Hz/s. The carrier optical frequency can be tuned over 350 MHz while in lock.

White Dwarf Critical Tests for Modified Gravity.

PubMed

Jain, Rajeev Kumar; Kouvaris, Chris; Nielsen, Niklas Grønlund

2016-04-15

Scalar-tensor theories of gravity can lead to modifications of the gravitational force inside astrophysical objects. We exhibit that compact stars such as white dwarfs provide a unique setup to test beyond Horndeski theories of G^{3} type. We obtain stringent and independent constraints on the parameter ϒ characterizing the deviations from Newtonian gravity using the mass-radius relation, the Chandrasekhar mass limit, and the maximal rotational frequency of white dwarfs. We find that white dwarfs impose stronger constraints on ϒ than red and brown dwarfs.

Quantitative elemental imaging of heterogeneous catalysts using laser-induced breakdown spectroscopy

NASA Astrophysics Data System (ADS)

Trichard, F.; Sorbier, L.; Moncayo, S.; Blouët, Y.; Lienemann, C.-P.; Motto-Ros, V.

2017-07-01

Currently, the use of catalysis is widespread in almost all industrial processes; its use improves productivity, synthesis yields and waste treatment as well as decreases energy costs. The increasingly stringent requirements, in terms of reaction selectivity and environmental standards, impose progressively increasing accuracy and control of operations. Meanwhile, the development of characterization techniques has been challenging, and the techniques often require equipment with high complexity. In this paper, we demonstrate a novel elemental approach for performing quantitative space-resolved analysis with ppm-scale quantification limits and μm-scale resolution. This approach, based on laser-induced breakdown spectroscopy (LIBS), is distinguished by its simplicity, all-optical design, and speed of operation. This work analyzes palladium-based porous alumina catalysts, which are commonly used in the selective hydrogenation process, using the LIBS method. We report an exhaustive study of the quantification capability of LIBS and its ability to perform imaging measurements over a large dynamic range, typically from a few ppm to wt%. These results offer new insight into the use of LIBS-based imaging in the industry and paves the way for innumerable applications.

ADX - Advanced Divertor and RF Tokamak Experiment

NASA Astrophysics Data System (ADS)

Greenwald, Martin; Labombard, Brian; Bonoli, Paul; Irby, Jim; Terry, Jim; Wallace, Greg; Vieira, Rui; Whyte, Dennis; Wolfe, Steve; Wukitch, Steve; Marmar, Earl

2015-11-01

The Advanced Divertor and RF Tokamak Experiment (ADX) is a design concept for a compact high-field tokamak that would address boundary plasma and plasma-material interaction physics challenges whose solution is critical for the viability of magnetic fusion energy. This device would have two crucial missions. First, it would serve as a Divertor Test Tokamak, developing divertor geometries, materials and operational scenarios that could meet the stringent requirements imposed in a fusion power plant. By operating at high field, ADX would address this problem at a level of power loading and other plasma conditions that are essentially identical to those expected in a future reactor. Secondly, ADX would investigate the physics and engineering of high-field-side launch of RF waves for current drive and heating. Efficient current drive is an essential element for achieving steady-state in a practical, power producing fusion device and high-field launch offers the prospect of higher efficiency, better control of the current profile and survivability of the launching structures. ADX would carry out this research in integrated scenarios that simultaneously demonstrate the required boundary regimes consistent with efficient current drive and core performance.

Latency study of the High Performance Time to Digital Converter for the ATLAS Muon Spectrometer trigger upgrade

NASA Astrophysics Data System (ADS)

Meng, X. T.; Levin, D. S.; Chapman, J. W.; Li, D. C.; Yao, Z. E.; Zhou, B.

2017-02-01

The High Performance Time to Digital Converter (HPTDC), a multi-channel ASIC designed by the CERN Microelectronics group, has been proposed for the digitization of the thin-Resistive Plate Chambers (tRPC) in the ATLAS Muon Spectrometer Phase-1 upgrade project. These chambers, to be staged for higher luminosity LHC operation, will increase trigger acceptance and reduce or eliminate the fake muon trigger rates in the barrel-endcap transition region, corresponding to pseudo-rapidity range 1<|η|<1.3. Low level trigger candidates must be flagged within a maximum latency of 1075 ns, thus imposing stringent signal processing time performance requirements on the readout system in general, and on the digitization electronics in particular. This paper investigates the HPTDC signal latency performance based on a specially designed evaluation board coupled with an external FPGA evaluation board, when operated in triggerless mode, and under hit rate conditions expected in Phase-I. This hardware based study confirms previous simulations and demonstrates that the HPTDC in triggerless operation satisfies the digitization timing requirements in both leading edge and pair modes.

Space shuttle orbiter auxiliary power unit development challenges

NASA Technical Reports Server (NTRS)

Lance, R.; Weary, D.

1985-01-01

When the flying spacecraft was approved for development, a power unit for the hydraulic system had to be developed. Unlike other systems on the orbiter, there was no precedent in earlier spacecraft for a hydraulic system nor for the power unit to drive the hydraulic pumps. The only prototypes available were airplane auxiliary power units (APU), which were not required to operate in the severe environments of a spacecraft nor to have the longevity of an orbiter hydraulic power unit. The challenge was to build a hydraulic power unit which could operate in 0g or 3g, in a vacuum or at sea level pressure, and at -65 F or 225 F, which would be capable of restarting while hot, and which would be capable of sustaining the hydraulic loads for the life of the orbiter. The basic approach to providing hydraulic power for the orbiter was to use a small, high speed, monopropellant fueled turbine power unit to drive a conventional aircraft type hydraulic pump. The stringent requirements imposed on the orbiter APU quickly made this machine different from existing aircraft APUs.

Optical calibration of SNO +

NASA Astrophysics Data System (ADS)

Leming, Edward; SNO+ Collaboration

2015-04-01

Situated 2 km underground in Sudbury, Northern Ontario, the SNO + detector consists of an acrylic sphere 12 m in diameter containing 780 tons of target mass, surrounded by approximately 9,500 PMTs. For SNO, this target mass was heavy water, however the change to SNO + is defined by the change of this target mass to a novel scintillator. With the lower energy threshold, low intrinsic radioactivity levels and the best shielding against muons and cosmogenic activation of all existing neutrino experiments, SNO + will be sensitive to exciting new physics. The experiment will be studying solar, reactor, super nova and geo-neutrinos, though the main purpose of SNO + is the search for neutrinoless double-beta decay of Te-130. To meet the requirements imposed by the physics on detector performance, a detailed optical calibration is needed. Source deployment must be kept to a minimum and eliminated if possible, in order to meet the stringent radiopurity requirements. This led to the development of the Embedded LED/laser Light Injection Entity (ELLIE) system. This talk provides a summary of the upgrades to from SNO to SNO +, discussing the requirements on and methods of optical calibration, focusing on the deployed laserball and ELLIE system.

Short seed longevity, variable germination conditions, and infrequent establishment events provide a narrow window for Yucca brevifolia (Agavaceae) recruitment

USGS Publications Warehouse

Bryant, M.; Reynolds, J.; DeFalco, Lesley A.; Esque, Todd C.

2012-01-01

PREMISE OF THE STUDY: The future of long-lived stand-forming desert plants such as Yucca brevifolia (Joshua tree) has come into question in light of climate variation and landscape-scale disturbances such as wildfire. Understanding plant establishment dynamics is important for mitigating the impacts of disturbances and promoting revegetation. • METHODS: We placed Y. brevifolia seeds in shallow caches and manipulated granivore access, nurse shrub effects, and the season of cache placement to determine conditions for seed germination and seedling establishment. • KEY RESULTS: Greatest seedling emergence occurred during spring and summer, when increased soil moisture was accompanied by warm soil temperatures. Late winter-spring emergence for cached seeds was enhanced beneath shrub canopies, but seedling survival declined beneath shrubs as temperatures increased in spring. Germinability of seed remaining in the soil was reduced from 50-68% after 12 mo residence time in soil and declined to <3% after 40 mo. Following dispersal from parent plants, seeds are either removed by granivores or lose germinability, imposing substantial losses of potential germinants. • CONCLUSIONS: Specific germination and establishment requirements impose stringent limits on recruitment rates for Y. brevifolia. Coupled with infrequent seed availability, the return rates to prefire densities and demographic structure may require decades to centuries, especially in light of potential changes to regional desert climate in combination with the potential for fire recurrence. Demographic patterns are predicted to vary spatially in response to environmental variability that limits recruitment and may already be apparent among extant populations.

40 CFR 35.910-7 - Fiscal Year 1977 Supplemental Appropriations Act allotments.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (secondary treatment, more stringent treatment required to meet water quality standards, and interceptor..., and V (secondary treatment, more stringent treatment required to meet water quality standards... Mexico 3,272,000 New York 105,294,000 North Carolina 20,722,000 North Dakota 3,272,000 Ohio 55,522,000...

Assessment of Instructions on Protection Against Food Contaminated with Radiocesium in Japan in 2011.

PubMed

Seto, Mayumi; Uriu, Koichiro; Kawaguchi, Isao; Yokomizo, Hiroyuki

2018-06-01

The Japan Ministry of Health, Labour and Welfare (MHLW) has published instructions for radiological protection against food after the Fukushima Daiichi nuclear power plant accident in 2011. Following the instructions, the export and consumption of food items identified as being contaminated were restricted for a certain period. We assessed the validity of the imposed restriction periods for two representative vegetables (spinach and cabbage) grown in Fukushima Prefecture from two perspectives: effectiveness for reducing dietary dose and economic efficiency. To assess effectiveness, we estimated the restriction period required to maintain consumers' dose below the guidance dose levels. To assess economic efficiency, we estimated the restriction period that maximizes the net benefit to taxpayers. All estimated restriction periods were shorter than the actual restriction periods imposed on spinach and cabbage from Fukushima in 2011, which indicates that the food restriction effectively maintained consumers' dietary dose below the guidance dose level, but in an economically inefficient manner. We also evaluated the response of the restriction period to the sample size for each weekly food safety test and the instructions for when to remove the restriction. Stringent MHLW instructions seemed to sufficiently reduce consumers' health risk even when the sample size for the weekly food safety test was small, but tended to increase the economic cost to taxpayers. © 2017 Society for Risk Analysis.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aranda, J. I.; Tututi, E. S.; Ramirez-Zavaleta, F.

The size of the branching ratios for the {tau}{yields}{mu}{gamma} and {tau}{yields}{mu}{gamma}{gamma} decays induced by a lepton flavor violating Higgs interaction H{tau}{mu} is studied in the framework of effective field theories. The best constraint on the H{tau}{mu} vertex, derived from the know measurement on the muon anomalous magnetic moment, is used to impose the upper bounds Br({tau}{yields}{mu}{gamma})<7.5x10{sup -10} and Br({tau}{yields}{mu}{gamma}{gamma})<2.3x10{sup -12}, which are more stringent than current experimental limits on this class of transitions.

Advances in x-ray framing cameras at the National Ignition Facility to improve quantitative precision in x-ray imaging

DOE PAGES

Benedetti, L. R.; Holder, J. P.; Perkins, M.; ...

2016-02-26

We describe an experimental method to measure the gate profile of an x-ray framing camera and to determine several important functional parameters: relative gain (between strips), relative gain droop (within each strip), gate propagation velocity, gate width, and actual inter-strip timing. Several of these parameters cannot be measured accurately by any other technique. This method is then used to document cross talk-induced gain variations and artifacts created by radiation that arrives before the framing camera is actively amplifying x-rays. Electromagnetic cross talk can cause relative gains to vary significantly as inter-strip timing is varied. This imposes a stringent requirement formore » gain calibration. If radiation arrives before a framing camera is triggered, it can cause an artifact that manifests as a high-intensity, spatially varying background signal. Furthermore, we have developed a device that can be added to the framing camera head to prevent these artifacts.« less

Advances in x-ray framing cameras at the National Ignition Facility to improve quantitative precision in x-ray imaging.

PubMed

Benedetti, L R; Holder, J P; Perkins, M; Brown, C G; Anderson, C S; Allen, F V; Petre, R B; Hargrove, D; Glenn, S M; Simanovskaia, N; Bradley, D K; Bell, P

2016-02-01

We describe an experimental method to measure the gate profile of an x-ray framing camera and to determine several important functional parameters: relative gain (between strips), relative gain droop (within each strip), gate propagation velocity, gate width, and actual inter-strip timing. Several of these parameters cannot be measured accurately by any other technique. This method is then used to document cross talk-induced gain variations and artifacts created by radiation that arrives before the framing camera is actively amplifying x-rays. Electromagnetic cross talk can cause relative gains to vary significantly as inter-strip timing is varied. This imposes a stringent requirement for gain calibration. If radiation arrives before a framing camera is triggered, it can cause an artifact that manifests as a high-intensity, spatially varying background signal. We have developed a device that can be added to the framing camera head to prevent these artifacts.

The dynamic characteristics of a turbo-rotor simulator supported on gas-lubricated foil bearings. Part 1: Response to rotating imbalance and unidirectional excitation

NASA Technical Reports Server (NTRS)

Licht, L.

1970-01-01

A sixteen-inch rotor, weighing approximately twenty-one pounds, was supported by air-lubricated foil bearings. In physical size and in mass distribution, the rotor closely matched that of an experimental Brayton cycle turboalternator unit. The rotor was stable in both vertical horizontal attitudes at speeds up to 50,000 rpm. A detailed description of the experimental apparatus and of the foil bearing design are given. The paper contains data on response of the rotor to rotating imbalance, symmetric and asymmetric, and to excitation by means of a vibrator (shake table). It is concluded that the gas-lubricated foil bearing suspension is free from fractional frequency whirl and suffers no loss of load capacity when excited at frequency equal to half the rotational speed. In contrast to rigid gas bearings, the foil bearing imposes no stringent requirements with respect to dimensional tolerances, cleanliness, or limitations of journal motion within the narrow confines of bearing clearance.

NIST torsion oscillator viscometer response: Performance on the LeRC active vibration isolation platform

NASA Technical Reports Server (NTRS)

Berg, Robert F.; Grodsinsky, Carlos M.

1992-01-01

Critical point viscosity measurements are limited to their reduced temperature approach to T(sub c) in an Earth bound system, because of density gradients imposed by gravity. Therefore, these classes of experiments have been proposed as good candidates for 'microgravity' science experiments where this limitation is not present. The nature of these viscosity measurements dictate hardware that is sensitive to low frequency excitations. Because of the vibratory acceleration sensitivity of a torsion oscillator viscometer, used to acquire such measurements, a vibration isolation sensitivity test was performed on candidate 'microgravity' hardware to study the possibility of meeting the stringent oscillatory sensitivity requirements of a National Institute of Standards and Technology (NIST) torsion oscillator viscometer. A prototype six degree of freedom active magnetic isolation system, developed at NASA Lewis Research Center, was used as the isolation system. The ambient acceleration levels of the platform were reduced to the noise floor levels of its control sensors, about one microgravity in the 0.1 to 10 Hz bandwidth.

Solar Pumped Lasers and Their Applications

NASA Technical Reports Server (NTRS)

Lee, Ja H.

1991-01-01

Since 1980, NASA has been pursuing high power solar lasers as part of the space power beaming program. Materials in liquid, solid, and gas phases have been evaluated against the requirements for solar pumping. Two basic characteristics of solar insolation, namely its diffuse irradiance and 5800 K blackbody-like spectrum, impose rather stringent requirements for laser excitation. However, meeting these requirements is not insurmountable as solar thermal energy technology has progressed today, and taking advantage of solar pumping lasers is becoming increasingly attractive. The high density photons of concentrated solar energy have been used for mainly electric power generation and thermal processing of materials by the DOE Solar Thermal Technologies Program. However, the photons can interact with materials through many other direct kinetic paths, and applications of the concentrated photons could be extended to processes requiring photolysis, photosynthesis, and photoexcitation. The use of solar pumped lasers on Earth seems constrained by economics and sociopolitics. Therefore, prospective applications may be limited to those that require use of quantum effects and coherency of the laser in order to generate extremely high value products and services when conventional and inexpensive means are ineffective or impossible. The new applications already proposed for concentrated solar photons, such as destruction of hazardous waste, production of renewable fuel, production of fertilizer, and air/water pollution controls, may benefit from the use of inexpensive solar pumped laser matched with the photochemical kinetics of these processes.

Critical examination of the uniformity requirements for single-photon emission computed tomography.

PubMed

O'Connor, M K; Vermeersch, C

1991-01-01

It is generally recognized that single-photon emission computed tomography (SPECT) imposes very stringent requirements on gamma camera uniformity to prevent the occurrence of ring artifacts. The purpose of this study was to examine the relationship between nonuniformities in the planar data and the magnitude of the consequential ring artifacts in the transaxial data, and how the perception of these artifacts is influenced by factors such as reconstruction matrix size, reconstruction filter, and image noise. The study indicates that the relationship between ring artifact magnitude and image noise is essentially independent of the acquisition or reconstruction matrix sizes, but is strongly dependent upon the type of smoothing filter applied during the reconstruction process. Furthermore, the degree to which a ring artifact can be perceived above image noise is dependent on the size and location of the nonuniformity in the planar data, with small nonuniformities (1-2 pixels wide) close to the center of rotation being less perceptible than those further out (8-20 pixels). Small defects or nonuniformities close to the center of rotation are thought to cause the greatest potential corruption to tomographic data. The study indicates that such may not be the case. Hence the uniformity requirements for SPECT may be less demanding than was previously thought.

Auralization Architectures for NASA?s Next Generation Aircraft Noise Prediction Program

NASA Technical Reports Server (NTRS)

Rizzi, Stephen A.; Lopes, Leonard V.; Burley, Casey L.; Aumann, Aric R.

2013-01-01

Aircraft community noise is a significant concern due to continued growth in air traffic, increasingly stringent environmental goals, and operational limitations imposed by airport authorities. The assessment of human response to noise from future aircraft can only be afforded through laboratory testing using simulated flyover noise. Recent work by the authors demonstrated the ability to auralize predicted flyover noise for a state-of-the-art reference aircraft and a future hybrid wing body aircraft concept. This auralization used source noise predictions from NASA's Aircraft NOise Prediction Program (ANOPP) as input. The results from this process demonstrated that auralization based upon system noise predictions is consistent with, and complementary to, system noise predictions alone. To further develop and validate the auralization process, improvements to the interfaces between the synthesis capability and the system noise tools are required. This paper describes the key elements required for accurate noise synthesis and introduces auralization architectures for use with the next-generation ANOPP (ANOPP2). The architectures are built around a new auralization library and its associated Application Programming Interface (API) that utilize ANOPP2 APIs to access data required for auralization. The architectures are designed to make the process of auralizing flyover noise a common element of system noise prediction.

Conceptual design of the cryostat for the new high luminosity (HL-LHC) triplet magnets

NASA Astrophysics Data System (ADS)

Ramos, D.; Parma, V.; Moretti, M.; Eymin, C.; Todesco, E.; Van Weelderen, R.; Prin, H.; Berkowitz Zamora, D.

2017-12-01

The High Luminosity LHC (HL-LHC) is a project to upgrade the LHC collider after 2020-2025 to increase the integrated luminosity by about one order of magnitude and extend the physics production until 2035. An upgrade of the focusing triplets insertion system for the ATLAS and CMS experiments is foreseen using superconducting magnets operating in a pressurised superfluid helium bath at 1.9 K. This will require the design and construction of four continuous cryostats, each about sixty meters in length and one meter in diameter, for the final beam focusing quadrupoles, corrector magnets and beam separation dipoles. The design is constrained by the dimensions of the existing tunnel and accessibility restrictions imposing the integration of cryogenic piping inside the cryostat, thus resulting in a very compact integration. As the alignment and position stability of the magnets is crucial for the luminosity performance of the machine, the magnet support system must be carefully designed in order to cope with parasitic forces and thermo-mechanical load cycles. In this paper, we present the conceptual design of the cryostat and discuss the approach to address the stringent and often conflicting requirements of alignment, integration and thermal aspects.

An evidential reasoning-based AHP approach for the selection of environmentally-friendly designs

DOE Office of Scientific and Technical Information (OSTI.GOV)

NG, C.Y., E-mail: ng.cy@cityu.edu.hk

Due to the stringent environmental regulatory requirements being imposed by cross-national bodies in recent years, manufacturers have to minimize the environmental impact of their products. Among those environmental impact evaluation tools available, Life Cycle Assessment (LCA) is often employed to quantify the product's environmental impact throughout its entire life cycle. However, owing to the requirements of expert knowledge in environmental science and vast effort for data collection in carrying out LCA, as well as the common absence of complete product information during product development processes, there is a need to develop a more suitable tool for product designers. An evidentialmore » reasoning-based approach, which aims at providing a fast-track method to perform design alternative evaluations for non-LCA experts, is therefore introduced as a new initiative to deal with the incomplete or uncertain information. The proposed approach also enables decision makers to quantitatively assess the life cycle phases and design alternatives by comparing their potential environmental impacts, thus effectively and efficiently facilitates the identification of greener designs. A case application is carried out to demonstrate the applicability of the proposed approach.« less

Space Qualification of Laser Diode Arrays

NASA Technical Reports Server (NTRS)

Troupaki, Elisavet; Kashem, Nasir B.; Allan, Graham R.; Vasilyev, Aleksey; Stephen, Mark

2005-01-01

Laser instruments have great potential in enabling a new generation of remote-sensing scientific instruments. NASA s desire to employ laser instruments aboard satellites, imposes stringent reliability requirements under severe conditions. As a result of these requirements, NASA has a research program to understand, quantify and reduce the risk of failure to these instruments when deployed on satellites. Most of NASA s proposed laser missions have base-lined diode-pumped Nd:YAG lasers that generally use quasi-constant wave (QCW), 808 nm Laser Diode Arrays (LDAs). Our group has an on-going test program to measure the performance of these LDAs when operated in conditions replicating launch and orbit. In this paper, we report on the results of tests designed to measure the effect of vibration loads simulating launch into space and the radiation environment encountered on orbit. Our primary objective is to quantify the performance of the LDAs in conditions replicating those of a satellite instrument, determine their limitations and strengths which will enable better and more robust designs. To this end we have developed a systematic testing strategy to quantify the effect of environmental stresses on the optical and electrical properties of the LDA.

Oil Dependence, Climate Change and Energy Security: Will Constraints on Oil Shape our Climate Future or Vice Versa?

NASA Astrophysics Data System (ADS)

Mignone, B. K.

2008-12-01

Threats to US and global energy security take several forms. First, the overwhelming dependence on oil in the transport sector leaves the US economy (and others) vulnerable to supply shocks and price volatility. Secondly, the global dependence on oil inflates prices and enhances the transfer of wealth to authoritarian regimes. Finally, the global reliance on fossil fuels more generally jeopardizes the stability of the climate system. These three threats - economic, strategic and environmental - can only be mitigated through a gradual substitution away from fossil fuels (both coal and oil) on a global scale. Such large-scale substitution could occur in response to potential resource constraints or in response to coordinated government policies in which these externalities are explicitly internalized. Here, I make use of a well-known integrated assessment model (MERGE) to examine both possibilities. When resource limits are considered alone, global fuel use tends to shift toward even more carbon-intensive resources, like oil shale or liquids derived from coal. On the other hand, when explicit carbon constraints are imposed, the fuel sector response is more complex. Generally, less stringent climate targets can be satisfied entirely through reductions in global coal consumption, while more stringent targets require simultaneous reductions in both coal and oil consumption. Taken together, these model results suggest that resource constraints alone will only exacerbate the climate problem, while a subset of policy-driven carbon constraints may yield tangible security benefits (in the form of reduced global oil consumption) in addition to the intended environmental outcome.

Global Constraints on Anomalous Triple Gauge Couplings in the Effective Field Theory Approach.

PubMed

Falkowski, Adam; González-Alonso, Martín; Greljo, Admir; Marzocca, David

2016-01-08

We present a combined analysis of LHC Higgs data (signal strengths) together with LEP-2 WW production measurements. To characterize possible deviations from the standard model (SM) predictions, we employ the framework of an effective field theory (EFT) where the SM is extended by higher-dimensional operators suppressed by the mass scale of new physics Λ. The analysis is performed consistently at the order Λ(-2) in the EFT expansion keeping all the relevant operators. While the two data sets suffer from flat directions, together they impose stringent model-independent constraints on the anomalous triple gauge couplings.

Invisibility cloaking in the diffusive-light limit (presentation video)

NASA Astrophysics Data System (ADS)

Schittny, Robert; Kadic, Muamer; Wegener, Martin

2014-09-01

Albert Einstein's theory of relativity imposes stringent limitations to making macroscopic objects invisible with respect to electromagnetic light waves propagating in vacuum. These limitations are not relevant though for propagation of light in diffusive media like fog or milk because the effective energy speed is significantly lower than in vacuum due to multiple scattering events. Here, by exploiting the close mathematical analogy between the electrostatic or near-field limit of optics on the one hand and light diffusion on the other hand, we design, fabricate, and characterize simple core-shell cloaking structures for diffusive light propagation in cylindrical and spherical geometry.

Dark matter detectors as dark photon helioscopes.

PubMed

An, Haipeng; Pospelov, Maxim; Pradler, Josef

2013-07-26

Light new particles with masses below 10 keV, often considered as a plausible extension of the standard model, will be emitted from the solar interior and can be detected on Earth with a variety of experimental tools. Here, we analyze the new "dark" vector state V, a massive vector boson mixed with the photon via an angle κ, that in the limit of the small mass mV has its emission spectrum strongly peaked at low energies. Thus, we utilize the constraints on the atomic ionization rate imposed by the results of the XENON10 experiment to set the limit on the parameters of this model: κ×mV<3×10(-12)  eV. This makes low-threshold dark matter experiments the most sensitive dark vector helioscopes, as our result not only improves current experimental bounds from other searches by several orders of magnitude but also surpasses even the most stringent astrophysical and cosmological limits in a seven-decade-wide interval of mV. We generalize this approach to other light exotic particles and set the most stringent direct constraints on "minicharged" particles.

40 CFR 281.37 - Financial responsibility for UST systems containing petroleum.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Financial responsibility for UST... for No-Less-Stringent § 281.37 Financial responsibility for UST systems containing petroleum. (a) In order to be considered no less stringent than the federal requirements for financial responsibility for...

New strings for old Veneziano amplitudes. II. Group-theoretic treatment

NASA Astrophysics Data System (ADS)

Kholodenko, A. L.

2006-09-01

In this part of our four parts work we use theory of polynomial invariants of finite pseudo-reflection groups in order to reconstruct both the Veneziano and Veneziano-like (tachyon-free) amplitudes and the generating function reproducing these amplitudes. We demonstrate that such generating function and amplitudes associated with it can be recovered with help of finite dimensional exactly solvableN=2 supersymmetric quantum mechanical model known earlier from works of Witten, Stone and others. Using the Lefschetz isomorphism theorem we replace traditional supersymmetric calculations by the group-theoretic thus solving the Veneziano model exactly using standard methods of representation theory. Mathematical correctness of our arguments relies on important theorems by Shepard and Todd, Serre and Solomon proven respectively in the early 50s and 60s and documented in the monograph by Bourbaki. Based on these theorems, we explain why the developed formalism leaves all known results of conformal field theories unchanged. We also explain why these theorems impose stringent requirements connecting analytical properties of scattering amplitudes with symmetries of space-time in which such amplitudes act.

Real-time vehicle emissions monitoring using a compact LiDAR system and conventional instruments: first results of an experimental campaign in a suburban area in southern Italy

NASA Astrophysics Data System (ADS)

Parracino, Stefano; Richetta, Maria; Gelfusa, Michela; Malizia, Andrea; Bellecci, Carlo; De Leo, Leonardo; Perrimezzi, Carlo; Fin, Alessandro; Forin, Marco; Giappicucci, Francesca; Grion, Massimo; Marchese, Giuseppe; Gaudio, Pasquale

2016-10-01

Urban air pollution causes deleterious effects on human health and the environment. To meet stringent standards imposed by the European Commission, advanced measurement methods are required. Remote sensing techniques, such as light detection and ranging (LiDAR), can be a valuable option for evaluating particulate matter (PM), emitted by vehicles in urban traffic, with high sensitivity and in shorter time intervals. Since air quality problems persist not only in large urban areas, a measuring campaign was specifically performed in a suburban area of Crotone, Italy, using both a compact LiDAR system and conventional instruments for real-time vehicle emissions monitoring along a congested road. First results reported in this paper show a strong dependence between variations of LiDAR backscattering signals and traffic-related air pollution levels. Moreover, time-resolved LiDAR data averaged in limited regions, directly above conventional monitoring stations at the border of an intersection, were found to be linearly correlated to the PM concentration levels with a correlation coefficient between 0.75 and 0.84.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dragone, A; /SLAC; Pratte, J.F.

An ASIC for the readout of signals from X-ray Active Matrix Pixel Sensor (XAMPS) detectors to be used at the Linac Coherent Light Source (LCLS) is presented. The X-ray Pump Probe (XPP) instrument, for which the ASIC has been designed, requires a large input dynamic range on the order of 104 photons at 8 keV with a resolution of half a photon FWHM. Due to the size of the pixel and the length of the readout line, large input capacitance is expected, leading to stringent requirement on the noise optimization. Furthermore, the large number of pixels needed for a goodmore » position resolution and the fixed LCLS beam period impose limitations on the time available for the single pixel readout. Considering the periodic nature of the LCLS beam, the ASIC developed for this application is a time-variant system providing low-noise charge integration, filtering and correlated double sampling. In order to cope with the large input dynamic range a charge pump scheme implementing a zero-balance measurement method has been introduced. It provides an on chip 3-bit coarse digital conversion of the integrated charge. The residual charge is sampled using correlated double sampling into analog memory and measured with the required resolution. The first 64 channel prototype of the ASIC has been fabricated in TSMC CMOS 0.25 {micro}m technology. In this paper, the ASIC architecture and performances are presented.« less

Determining coronal electron temperatures from observations with UVCS/SOHO

NASA Technical Reports Server (NTRS)

Fineschi, S.; Esser, R.; Habbal, S. R.; Karovska, M.; Romoli, M.; Strachan, L.; Kohl, J. L.; Huber, M. C. E.

1995-01-01

The electron temperature is a fundamental physical parameter of the coronal plasma. Currently, there are no direct measurements of this quantity in the extended corona. Observations with the Ultraviolet Coronagraph Spectrometer (UVCS) aboard the upcoming Solar and Heliospheric Observatory (SOHO) mission can provide the most direct determination of the electron kinetic temperature (or, more precisely, the electron velocity distribution along the line of sight). This measurement is based on the observation of the Thomson-scattered Lyman alpha (Ly-alpha) profile. This observation is made particularly challenging by the fact that the integrated intensity of the electron-scattered Ly-alpha line is about 10(exp 3) times fainter than that of the resonantly-scattered Ly-alpha component. In addition, the former is distributed across 50 A (FWHM), unlike the latter that is concentrated in 1 A. These facts impose stringent requirements on the stray-light rejection properties of the coronagraph/spectrometer, and in particular on the requirements for the grating. We make use of laboratory measurements of the UVCS Ly-alpha grating stray-light, and of simulated electron-scattered Ly-alpha profiles to estimate the expected confidence levels of electron temperature determination. Models of different structures typical of the corona (e.g., streamers, coronal holes) are used for this parameter study.

Fast force actuators for LSST primary/tertiary mirror

NASA Astrophysics Data System (ADS)

Hileman, Edward; Warner, Michael; Wiecha, Oliver

2010-07-01

The very short slew times and resulting high inertial loads imposed upon the Large Synoptic Survey Telescope (LSST) create new challenges to the primary mirror support actuators. Traditionally large borosilicate mirrors are supported by pneumatic systems, which is also the case for the LSST. These force based actuators bear the weight of the mirror and provide active figure correction, but do not define the mirror position. A set of six locating actuators (hardpoints) arranged in a hexapod fashion serve to locate the mirror. The stringent dynamic requirements demand that the force actuators must be able to counteract in real time for dynamic forces on the hardpoints during slewing to prevent excessive hardpoint loads. The support actuators must also maintain the prescribed forces accurately during tracking to maintain acceptable mirror figure. To meet these requirements, candidate pneumatic cylinders incorporating force feedback control and high speed servo valves are being tested using custom instrumentation with automatic data recording. Comparative charts are produced showing details of friction, hysteresis cycles, operating bandwidth, and temperature dependency. Extremely low power actuator controllers are being developed to avoid heat dissipation in critical portions of the mirror and also to allow for increased control capabilities at the actuator level, thus improving safety, performance, and the flexibility of the support system.

A Study on a Microwave-Driven Smart Material Actuator

NASA Technical Reports Server (NTRS)

Choi, Sang H.; Chu, Sang-Hyon; Kwak, M.; Cutler, A. D.

2001-01-01

NASA s Next Generation Space Telescope (NGST) has a large deployable, fragmented optical surface (greater than or = 2 8 m in diameter) that requires autonomous correction of deployment misalignments and thermal effects. Its high and stringent resolution requirement imposes a great deal of challenge for optical correction. The threshold value for optical correction is dictated by lambda/20 (30 nm for NGST optics). Control of an adaptive optics array consisting of a large number of optical elements and smart material actuators is so complex that power distribution for activation and control of actuators must be done by other than hard-wired circuitry. The concept of microwave-driven smart actuators is envisioned as the best option to alleviate the complexity associated with hard-wiring. A microwave-driven actuator was studied to realize such a concept for future applications. Piezoelectric material was used as an actuator that shows dimensional change with high electric field. The actuators were coupled with microwave rectenna and tested to correlate the coupling effect of electromagnetic wave. In experiments, a 3x3 rectenna patch array generated more than 50 volts which is a threshold voltage for 30-nm displacement of a single piezoelectric material. Overall, the test results indicate that the microwave-driven actuator concept can be adopted for NGST applications.

An ultrabright and monochromatic electron point source made of a LaB6 nanowire

NASA Astrophysics Data System (ADS)

Zhang, Han; Tang, Jie; Yuan, Jinshi; Yamauchi, Yasushi; Suzuki, Taku T.; Shinya, Norio; Nakajima, Kiyomi; Qin, Lu-Chang

2016-03-01

Electron sources in the form of one-dimensional nanotubes and nanowires are an essential tool for investigations in a variety of fields, such as X-ray computed tomography, flexible displays, chemical sensors and electron optics applications. However, field emission instability and the need to work under high-vacuum or high-temperature conditions have imposed stringent requirements that are currently limiting the range of application of electron sources. Here we report the fabrication of a LaB6 nanowire with only a few La atoms bonded on the tip that emits collimated electrons from a single point with high monochromaticity. The nanostructured tip has a low work function of 2.07 eV (lower than that of Cs) while remaining chemically inert, two properties usually regarded as mutually exclusive. Installed in a scanning electron microscope (SEM) field emission gun, our tip shows a current density gain that is about 1,000 times greater than that achievable with W(310) tips, and no emission decay for tens of hours of operation. Using this new SEM, we acquired very low-noise, high-resolution images together with rapid chemical compositional mapping using a tip operated at room temperature and at 10-times higher residual gas pressure than that required for W tips.

Measurement of GEP/GMP to Q2 = 5.6 GEV2 via Recoil Polarization at Jefferson Lab

NASA Astrophysics Data System (ADS)

Gayou, Olivier

2001-10-01

The measurement of the elastic form factors is a key ingredient to any complete understanding of the internal structure of the nucleons, and ultimately of the strong force. Precise data are essential to impose stringent tests on any QCD-based theory. The electromagnetic interaction provides a unique tool to investigate these form factors. In elastic electron scattering off a proton, the electron interacts with the nucleon exchanging a virtual photon. The electron-photon interaction is fully understood from QED, hence making the hadron vertex the only unknown of the reaction...

Realization of the Contextuality-Nonlocality Tradeoff with a Qubit-Qutrit Photon Pair

NASA Astrophysics Data System (ADS)

Zhan, Xiang; Zhang, Xin; Li, Jian; Zhang, Yongsheng; Sanders, Barry C.; Xue, Peng

2016-03-01

We report our experimental results on the no-disturbance principle, which imposes a fundamental monogamy relation on contextuality versus nonlocality. We employ a photonic qutrit-qubit hybrid to explore no-disturbance monogamy at the quantum boundary spanned by noncontextuality and locality inequalities. In particular, we realize the single point where the quantum boundary meets the no-disturbance boundary. Our results agree with quantum theory and satisfy the stringent monogamy relation thereby providing direct experimental evidence of a tradeoff between locally contextual correlations and spatially separated correlations. Thus, our experiment provides evidence that entanglement is a particular manifestation of a more fundamental quantum resource.

The Streptococcus agalactiae Stringent Response Enhances Virulence and Persistence in Human Blood

PubMed Central

Hooven, Thomas A.; Catomeris, Andrew J.; Bonakdar, Maryam; Tallon, Luke J.; Santana-Cruz, Ivette; Ott, Sandra; Daugherty, Sean C.; Tettelin, Hervé

2017-01-01

ABSTRACT Streptococcus agalactiae (group B Streptococcus [GBS]) causes serious infections in neonates. We previously reported a transposon sequencing (Tn-seq) system for performing genomewide assessment of gene fitness in GBS. In order to identify molecular mechanisms required for GBS to transition from a mucosal commensal lifestyle to bloodstream invasion, we performed Tn-seq on GBS strain A909 with human whole blood. Our analysis identified 16 genes conditionally essential for GBS survival in blood, of which 75% were members of the capsular polysaccharide (cps) operon. Among the non-cps genes identified as conditionally essential was relA, which encodes an enzyme whose activity is central to the bacterial stringent response—a conserved adaptation to environmental stress. We used blood coincubation studies of targeted knockout strains to confirm the expected growth defects of GBS deficient in capsule or stringent response activation. Unexpectedly, we found that the relA knockout strains demonstrated decreased expression of β-hemolysin/cytolysin, an important cytotoxin implicated in facilitating GBS invasion. Furthermore, chemical activation of the stringent response with serine hydroxamate increased β-hemolysin/cytolysin expression. To establish a mechanism by which the stringent response leads to increased cytotoxicity, we performed transcriptome sequencing (RNA-seq) on two GBS strains grown under stringent response or control conditions. This revealed a conserved decrease in the expression of genes in the arginine deiminase pathway during stringent response activation. Through coincubation with supplemental arginine and the arginine antagonist canavanine, we show that arginine availability is a determinant of GBS cytotoxicity and that the pathway between stringent response activation and increased virulence is arginine dependent. PMID:29109175

High resolution para-hydrogen induced polarization in inhomogeneous magnetic fields.

PubMed

Buljubasich, L; Prina, I; Franzoni, M B; Münnemann, K; Spiess, H W; Acosta, R H

2013-05-01

The application of parahydrogen for the generation of hyperpolarization has increased continuously during the last years. When the chemical reaction is carried out at the same field as the NMR experiment (PASADENA protocol) an antiphase signal is obtained, with a separation of the resonance lines of a few Hz. This imposes a stringent limit to the homogeneity of the magnetic field in order to avoid signal cancellation. In this work we detect the signal arising from hyperpolarized Hexene by means of a CPMG pulse train. After Fourier transformation the obtained J-spectra not only presents an enhanced spectral resolution but also avoids partial peak cancellation. Copyright © 2013 Elsevier Inc. All rights reserved.

Lattice Design for a High-Power Infrared FEL

NASA Astrophysics Data System (ADS)

Douglas, D. R.

1997-05-01

A 1 kW infrared FEL, funded by the U.S. Navy, is under construction at Jefferson Lab. This device will be driven by a compact, 42 MeV, 5 mA, energy-recovering, CW SRF-based linear accelerator to produce light in the 3-6.6 μm range. The machine concept comprises a 10 MeV injector, a linac based on a single high-gradient Jefferson Lab accelerator cryomodule, a wiggler and optical cavity, and an energy-recovery recirculation arc. Energy recovery limits cost and technical risk by reducing the RF power requirements in the driver accelerator. Following deceleration to 10 MeV, the beam is dumped. Stringent phase space requirements at the wiggler, low beam energy, and high beam current subject the accelerator lattice to numerous constraints. Principal considerations include: transport and delivery to the FEL of a high-quality, high-current beam; the impact of coherent synchrotron radiation (CSR) during beam recirculation transport; beam optics aberration control, to provide low-loss energy-recovery transport of a 5% relative momentum spread, high-current beam; attention to possible beam breakup (BBU) instabilities in the recirculating accelerator; and longitudinal phase space management during beam transport, to optimize RF drive system control during energy recovery and FEL operation. The presentation will address the design process and design solution for an accelerator transport lattice that meets the requirements imposed by these physical phenomena and operational necessities.

Engineering Design of ITER Prototype Fast Plant System Controller

NASA Astrophysics Data System (ADS)

Goncalves, B.; Sousa, J.; Carvalho, B.; Rodrigues, A. P.; Correia, M.; Batista, A.; Vega, J.; Ruiz, M.; Lopez, J. M.; Rojo, R. Castro; Wallander, A.; Utzel, N.; Neto, A.; Alves, D.; Valcarcel, D.

2011-08-01

The ITER control, data access and communication (CODAC) design team identified the need for two types of plant systems. A slow control plant system is based on industrial automation technology with maximum sampling rates below 100 Hz, and a fast control plant system is based on embedded technology with higher sampling rates and more stringent real-time requirements than that required for slow controllers. The latter is applicable to diagnostics and plant systems in closed-control loops whose cycle times are below 1 ms. Fast controllers will be dedicated industrial controllers with the ability to supervise other fast and/or slow controllers, interface to actuators and sensors and, if necessary, high performance networks. Two prototypes of a fast plant system controller specialized for data acquisition and constrained by ITER technological choices are being built using two different form factors. This prototyping activity contributes to the Plant Control Design Handbook effort of standardization, specifically regarding fast controller characteristics. Envisaging a general purpose fast controller design, diagnostic use cases with specific requirements were analyzed and will be presented along with the interface with CODAC and sensors. The requirements and constraints that real-time plasma control imposes on the design were also taken into consideration. Functional specifications and technology neutral architecture, together with its implications on the engineering design, were considered. The detailed engineering design compliant with ITER standards was performed and will be discussed in detail. Emphasis will be given to the integration of the controller in the standard CODAC environment. Requirements for the EPICS IOC providing the interface to the outside world, the prototype decisions on form factor, real-time operating system, and high-performance networks will also be discussed, as well as the requirements for data streaming to CODAC for visualization and archiving.

Quality assurance of intensity-modulated radiation therapy.

PubMed

Palta, Jatinder R; Liu, Chihray; Li, Jonathan G

2008-01-01

The current paradigm for the quality assurance (QA) program for intensity-modulated radiation therapy (IMRT) includes QA of the treatment planning system, QA of the delivery system, and patient-specific QA. Although the IMRT treatment planning and delivery system is the same as for conventional three-dimensional conformal radiation therapy, it has more parameters to coordinate and verify. Because of complex beam intensity modulation, each IMRT field often includes many small irregular off-axis fields, resulting in isodose distributions for each IMRT plan that are more conformal than those from conventional treatment plans. Therefore, these features impose a new and more stringent set of QA requirements for IMRT planning and delivery. The generic test procedures to validate dose calculation and delivery accuracy for both treatment planning and IMRT delivery have to be customized for each type of IMRT planning and delivery strategy. The rationale for such an approach is that the overall accuracy of IMRT delivery is incumbent on the piecewise uncertainties in both the planning and delivery processes. The end user must have well-defined evaluation criteria for each element of the planning and delivery process. Such information can potentially be used to determine a priori the accuracy of IMRT planning and delivery.

An ISVD-based Euclidian structure from motion for smartphones

NASA Astrophysics Data System (ADS)

Masiero, A.; Guarnieri, A.; Vettore, A.; Pirotti, F.

2014-06-01

The development of Mobile Mapping systems over the last decades allowed to quickly collect georeferenced spatial measurements by means of sensors mounted on mobile vehicles. Despite the large number of applications that can potentially take advantage of such systems, because of their cost their use is currently typically limited to certain specialized organizations, companies, and Universities. However, the recent worldwide diffusion of powerful mobile devices typically embedded with GPS, Inertial Navigation System (INS), and imaging sensors is enabling the development of small and compact mobile mapping systems. More specifically, this paper considers the development of a 3D reconstruction system based on photogrammetry methods for smartphones (or other similar mobile devices). The limited computational resources available in such systems and the users' request for real time reconstructions impose very stringent requirements on the computational burden of the 3D reconstruction procedure. This work takes advantage of certain recently developed mathematical tools (incremental singular value decomposition) and of photogrammetry techniques (structure from motion, Tomasi-Kanade factorization) to access very computationally efficient Euclidian 3D reconstruction of the scene. Furthermore, thanks to the presence of instrumentation for localization embedded in the device, the obtained 3D reconstruction can be properly georeferenced.

An assessment of the economic status of the antifriction bearing industry

NASA Astrophysics Data System (ADS)

Peterson, Donna J.; Kelley, Gerald T.; Myers, Myron G.

1991-10-01

Military equipment with moving parts requires antifriction bearings. Superprecision bearings, which are manufactured with closer tolerances under more stringent conditions, are often needed to meet high-performance characteristics such as silencing in submarines. A steady increase in imports of antifriction bearings coupled with reduced prices and profitability in the domestic industry led domestic manufacturers to seek legislative and regulatory relief from foreign competition. Since 1987, the Government has provided two types of relief to the industry. First, after a Department of Commerce investigation established that foreign producers were selling products in the U.S. market at prices below those they charged in their home markets, the Government imposed antidumping duties on several types of bearings from 12 countries. Second, the DoD restricted the purchase of antifriction bearing for use in defense end items to those of domestic manufacture. Although that restriction is due to expire on 30 Sep. 1991, the DoD may renew it for an additional 2 years if conditions warrant. This study assesses the current economic health of the U.S. antifriction bearing industry, analyzes the relative impact of the two forms of relief provided to the industry, and discusses the advantages and disadvantages of DoD's policy options.

Thermal transport in Si and Ge nanostructures in the `confinement' regime

NASA Astrophysics Data System (ADS)

Kwon, Soonshin; Wingert, Matthew C.; Zheng, Jianlin; Xiang, Jie; Chen, Renkun

2016-07-01

Reducing semiconductor materials to sizes comparable to the characteristic lengths of phonons, such as the mean-free-path (MFP) and wavelength, has unveiled new physical phenomena and engineering capabilities for thermal energy management and conversion systems. These developments have been enabled by the increasing sophistication of chemical synthesis, microfabrication, and atomistic simulation techniques to understand the underlying mechanisms of phonon transport. Modifying thermal properties by scaling physical size is particularly effective for materials which have large phonon MFPs, such as crystalline Si and Ge. Through nanostructuring, materials that are traditionally good thermal conductors can become good candidates for applications requiring thermal insulation such as thermoelectrics. Precise understanding of nanoscale thermal transport in Si and Ge, the leading materials of the modern semiconductor industry, is increasingly important due to more stringent thermal conditions imposed by ever-increasing complexity and miniaturization of devices. Therefore this Minireview focuses on the recent theoretical and experimental developments related to reduced length effects on thermal transport of Si and Ge with varying size from hundreds to sub-10 nm ranges. Three thermal transport regimes - bulk-like, Casimir, and confinement - are emphasized to describe different governing mechanisms at corresponding length scales.

Wet-weather urban discharges: implications from adopting the revised European Directive concerning the quality of bathing water.

PubMed

David, L M; Matos, J S

2005-01-01

Wet weather urban discharges are responsible for bathing water contamination. The proposal for a revised EU Directive concerning the quality of bathing water imposes significantly more stringent requirements for the management of bathing water quality, with particularly important repercussions on beaches subjected to short-term pollution incidents. The paper reviews the aspects from EU legislation most directly related to the problem of wet-weather discharges, placing special emphasis on the recent revision process of the Directive on bathing water quality, and evaluates the benefits of some potential solutions based on continuous modelling of a combined sewer system. Increasing the sewer system storage capacity or the STP hydraulic capacity may substantially reduce the untreated discharge volumes, but spill frequency reductions under 2 to 3 spill days per bathing season will hardly be achieved. Results show the severe strains that local rainfall patterns would place on compliance with the Commission's proposal for a revised Directive and highlight the importance of the changes introduced in the amended proposal recently approved by the Council, making it less prescriptive if adequate measures are adopted to prevent bathers' exposure to short-term pollution incidents.

Leptogenesis constraints on B - L breaking Higgs boson in TeV scale seesaw models

NASA Astrophysics Data System (ADS)

Dev, P. S. Bhupal; Mohapatra, Rabindra N.; Zhang, Yongchao

2018-03-01

In the type-I seesaw mechanism for neutrino masses, there exists a B - L symmetry, whose breaking leads to the lepton number violating mass of the heavy Majorana neutrinos. This would imply the existence of a new neutral scalar associated with the B - L symmetry breaking, analogous to the Higgs boson of the Standard Model. If in such models, the heavy neutrino decays are also responsible for the observed baryon asymmetry of the universe via the leptogenesis mechanism, the new seesaw scalar interactions with the heavy neutrinos will induce additional dilution terms for the heavy neutrino and lepton number densities. We make a detailed study of this dilution effect on the lepton asymmetry in three generic classes of seesaw models with TeV-scale B - L symmetry breaking, namely, in an effective theory framework and in scenarios with global or local U(1) B- L symmetry. We find that requiring successful leptogenesis imposes stringent constraints on the mass and couplings of the new scalar in all three cases, especially when it is lighter than the heavy neutrinos. We also discuss the implications of these new constraints and prospects of testing leptogenesis in presence of seesaw scalars at colliders.

Thermal transport in Si and Ge nanostructures in the 'confinement' regime.

PubMed

Kwon, Soonshin; Wingert, Matthew C; Zheng, Jianlin; Xiang, Jie; Chen, Renkun

2016-07-21

Reducing semiconductor materials to sizes comparable to the characteristic lengths of phonons, such as the mean-free-path (MFP) and wavelength, has unveiled new physical phenomena and engineering capabilities for thermal energy management and conversion systems. These developments have been enabled by the increasing sophistication of chemical synthesis, microfabrication, and atomistic simulation techniques to understand the underlying mechanisms of phonon transport. Modifying thermal properties by scaling physical size is particularly effective for materials which have large phonon MFPs, such as crystalline Si and Ge. Through nanostructuring, materials that are traditionally good thermal conductors can become good candidates for applications requiring thermal insulation such as thermoelectrics. Precise understanding of nanoscale thermal transport in Si and Ge, the leading materials of the modern semiconductor industry, is increasingly important due to more stringent thermal conditions imposed by ever-increasing complexity and miniaturization of devices. Therefore this Minireview focuses on the recent theoretical and experimental developments related to reduced length effects on thermal transport of Si and Ge with varying size from hundreds to sub-10 nm ranges. Three thermal transport regimes - bulk-like, Casimir, and confinement - are emphasized to describe different governing mechanisms at corresponding length scales.

A Simulation of the Front End Signal Digitization for the ATLAS Muon Spectrometer thin RPC trigger upgrade project

NASA Astrophysics Data System (ADS)

Meng, Xiangting; Chapman, John; Levin, Daniel; Dai, Tiesheng; Zhu, Junjie; Zhou, Bing; Um Atlas Group Team

2016-03-01

The ATLAS Muon Spectrometer Phase-I (and Phase-II) upgrade includes the BIS78 muon trigger detector project: two sets of eight very thin Resistive Place Chambers (tRPCs) combined with small Monitored Drift Tube (MDT) chambers in the pseudorapidity region 1<| η|<1.3. The tRPCs will be comprised of triplet readout layer in each of the eta and azimuthal phi coordinates, with about 400 readout strips per layer. The anticipated hit rate is 100-200 kHz per strip. Digitization of the strip signals will be done by 32-channel CERN HPTDC chips. The HPTDC is a highly configurable ASIC designed by the CERN Microelectronics group. It can work in both trigger and trigger-less modes, be readout in parallel or serially. For Phase-I operation, a stringent latency requirement of 43 bunch crossings (1075 ns) is imposed. The latency budget for the front end digitization must be kept to a minimal value, ideally less than 350 ns. We conducted detailed HPTDC latency simulations using the Behavioral Verilog code from the CERN group. We will report the results of these simulations run for the anticipated detector operating environment and for various HPTDC configurations.

A Survey on Multimedia-Based Cross-Layer Optimization in Visual Sensor Networks

PubMed Central

Costa, Daniel G.; Guedes, Luiz Affonso

2011-01-01

Visual sensor networks (VSNs) comprised of battery-operated electronic devices endowed with low-resolution cameras have expanded the applicability of a series of monitoring applications. Those types of sensors are interconnected by ad hoc error-prone wireless links, imposing stringent restrictions on available bandwidth, end-to-end delay and packet error rates. In such context, multimedia coding is required for data compression and error-resilience, also ensuring energy preservation over the path(s) toward the sink and improving the end-to-end perceptual quality of the received media. Cross-layer optimization may enhance the expected efficiency of VSNs applications, disrupting the conventional information flow of the protocol layers. When the inner characteristics of the multimedia coding techniques are exploited by cross-layer protocols and architectures, higher efficiency may be obtained in visual sensor networks. This paper surveys recent research on multimedia-based cross-layer optimization, presenting the proposed strategies and mechanisms for transmission rate adjustment, congestion control, multipath selection, energy preservation and error recovery. We note that many multimedia-based cross-layer optimization solutions have been proposed in recent years, each one bringing a wealth of contributions to visual sensor networks. PMID:22163908

Magnetic resonance imaging-compatible tactile sensing device based on a piezoelectric array.

PubMed

Hamed, Abbi; Masamune, Ken; Tse, Zion Tsz Ho; Lamperth, Michael; Dohi, Takeyoshi

2012-07-01

Minimally invasive surgery is a widely used medical technique, one of the drawbacks of which is the loss of direct sense of touch during the operation. Palpation is the use of fingertips to explore and make fast assessments of tissue morphology. Although technologies are developed to equip minimally invasive surgery tools with haptic feedback capabilities, the majority focus on tissue stiffness profiling and tool-tissue interaction force measurement. For greatly increased diagnostic capability, a magnetic resonance imaging-compatible tactile sensor design is proposed, which allows minimally invasive surgery to be performed under image guidance, combining the strong capability of magnetic resonance imaging soft tissue and intuitive palpation. The sensing unit is based on a piezoelectric sensor methodology, which conforms to the stringent mechanical and electrical design requirements imposed by the magnetic resonance environment The sensor mechanical design and the device integration to a 0.2 Tesla open magnetic resonance imaging scanner are described, together with the device's magnetic resonance compatibility testing. Its design limitations and potential future improvements are also discussed. A tactile sensing unit based on a piezoelectric sensor principle is proposed, which is designed for magnetic resonance imaging guided interventions.

Higgs naturalness and dark matter stability by scale invariance

NASA Astrophysics Data System (ADS)

Guo, Jun; Kang, Zhaofeng

2015-09-01

Extending the spacetime symmetries of standard model (SM) by scale invariance (SI) may address the Higgs naturalness problem. In this article we attempt to embed accidental dark matter (DM) into SISM, requiring that the symmetry protecting DM stability is accidental due to the model structure rather than imposed by hand. In this framework, if the light SM-like Higgs boson is the pseudo Goldstone boson of SI spontaneously breaking, we can even pine down the model, two-Higgs-doublets plus a real singlet: The singlet is the DM candidate and the extra Higgs doublet triggers electroweak symmetry breaking via the Coleman-Weinberg mechanism; Moreover, it dominates DM dynamics. We study spontaneously breaking of SI using the Gillard-Weinberg approach and find that the second doublet should acquire vacuum expectation value near the weak scale. Moreover, its components should acquire masses around 380 GeV except for a light CP-odd Higgs boson. Based on these features, we explore viable ways to achieve the correct relic density of DM, facing stringent constraints from direct detections of DM. For instance, DM annihilates into b b bar near the SM-like Higgs boson pole, or into a pair of CP-odd Higgs boson with mass above that pole.

Issues of environmental compliance in developing countries.

PubMed

Singh, S; Rajamani, S

2003-01-01

Environmental laws define the scarcity of environmental resources as they affect the factor endowment of a country and therefore its position in the international division of labour. There is now also a general agreement that applying the "polluter pays" principle should solve environmental problems. As the burden of abatement increases, as measured by the ratio of abatement expenditure to sales, there is definitely an incentive for firms to either invest in cleaner technology or more efficient abatement technology. There is also evidence that taxes and charges, designed to internalise externalities, can actually affect trade. It is interesting to know if the developing countries face particular market access problems in the face of stringent environmental standards and regulations. While it is true that stringent measures impose market access restrictions and cause limitations on competitiveness, this is much more widely felt by the developing countries because of lack of infrastructure and monitoring facilities, limited technology choices, inadequate access to environment-friendly raw materials, lack of complete information, presence of small-scale exporters and emergence of environmental standards in sectors of export interest to developing countries. The small and medium enterprises often divert sales either to the domestic market or to external markets where environmental requirements are less stringent, in order to save on their costs. In developing countries, 80% of the tanning industry is comprised of small and medium enterprises (SMEs) processing raw to semi-finished leather, usually less than 2 tons per day. In Europe and other developed countries the SMEs in the leather sector have vanished due to strict environmental legislation and this will likely occur in developing countries also. The environmental legislation has not always been practical, either because the laws are too ambitious or unrealistic in certain parameters, or because they have lacked effective instrumentation and institutional support. Some environmental regulations have not succeeded as they do not match the technical requirements and economic reality of the country or region, or because they do not take the institutional capabilities of the society that has to implement them into consideration. For the survival and sustenance of the SMEs in the leather industry, it may be a viable alternative to carry out the tanning process in a decentralized fashion such that the raw to semi-finished process is carried out in the large scale sector while the semi-finished to finished process could either be reserved or open to competition as per the countries' requirements. But the issue of concern is whether it is fair that the raw to semi-finished tanning process, containing 70% of the pollution discharge should be undertaken by developing countries alone, especially if it is at the cost of their survival! However, the game analysed in the paper reveals that tanning units in developing countries would prefer to comply with the regulations and stay in the industry, the alternatives being to collude or to compete!

Access to bacteriophage therapy: discouraging experiences from the human cell and tissue legal framework.

PubMed

Verbeken, G; Huys, I; De Vos, D; De Coninck, A; Roseeuw, D; Kets, E; Vanderkelen, A; Draye, J P; Rose, T; Jennes, S; Ceulemans, C; Pirnay, J P

2016-02-01

Cultures of human epithelial cells (keratinocytes) are used as an additional surgical tool to treat critically burnt patients. Initially, the production environment of keratinocyte grafts was regulated exclusively by national regulations. In 2004, the European Tissues and Cells Directive 2004/23/EC (transposed into Belgian Law) imposed requirements that resulted in increased production costs and no significant increase in quality and/or safety. In 2007, Europe published Regulation (EC) No. 1394/2007 on Advanced Therapy Medicinal Products. Overnight, cultured keratinocytes became (arguably) 'Advanced' Therapy Medicinal Products to be produced as human medicinal products. The practical impact of these amendments was (and still is) considerable. A similar development appears imminent in bacteriophage therapy. Bacteriophages are bacterial viruses that can be used for tackling the problem of bacterial resistance development to antibiotics. Therapeutic natural bacteriophages have been in clinical use for almost 100 years. Regulators today are framing the (re-)introduction of (natural) bacteriophage therapy into 'modern western' medicine as biological medicinal products, also subject to stringent regulatory medicinal products requirements. In this paper, we look back on a century of bacteriophage therapy to make the case that therapeutic natural bacteriophages should not be classified under the medicinal product regulatory frames as they exist today. It is our call to authorities to not repeat the mistake of the past. © FEMS 2015. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Methodologies for Salmonella enterica subsp. enterica Subtyping: Gold Standards and Alternatives▿

PubMed Central

Wattiau, Pierre; Boland, Cécile; Bertrand, Sophie

2011-01-01

For more than 80 years, subtyping of Salmonella enterica has been routinely performed by serotyping, a method in which surface antigens are identified based on agglutination reactions with specific antibodies. The serotyping scheme, which is continuously updated as new serovars are discovered, has generated over time a data set of the utmost significance, allowing long-term epidemiological surveillance of Salmonella in the food chain and in public health control. Conceptually, serotyping provides no information regarding the phyletic relationships inside the different Salmonella enterica subspecies. In epidemiological investigations, identification and tracking of salmonellosis outbreaks require the use of methods that can fingerprint the causative strains at a taxonomic level far more specific than the one achieved by serotyping. During the last 2 decades, alternative methods that could successfully identify the serovar of a given strain by probing its DNA have emerged, and molecular biology-based methods have been made available to address phylogeny and fingerprinting issues. At the same time, accredited diagnostics have become increasingly generalized, imposing stringent methodological requirements in terms of traceability and measurability. In these new contexts, the hand-crafted character of classical serotyping is being challenged, although it is widely accepted that classification into serovars should be maintained. This review summarizes and discusses modern typing methods, with a particular focus on those having potential as alternatives for classical serotyping or for subtyping Salmonella strains at a deeper level. PMID:21856826

Deep-space and near-Earth optical communications by coded orbital angular momentum (OAM) modulation.

PubMed

Djordjevic, Ivan B

2011-07-18

In order to achieve multi-gigabit transmission (projected for 2020) for the use in interplanetary communications, the usage of large number of time slots in pulse-position modulation (PPM), typically used in deep-space applications, is needed, which imposes stringent requirements on system design and implementation. As an alternative satisfying high-bandwidth demands of future interplanetary communications, while keeping the system cost and power consumption reasonably low, in this paper, we describe the use of orbital angular momentum (OAM) as an additional degree of freedom. The OAM is associated with azimuthal phase of the complex electric field. Because OAM eigenstates are orthogonal the can be used as basis functions for N-dimensional signaling. The OAM modulation and multiplexing can, therefore, be used, in combination with other degrees of freedom, to solve the high-bandwidth requirements of future deep-space and near-Earth optical communications. The main challenge for OAM deep-space communication represents the link between a spacecraft probe and the Earth station because in the presence of atmospheric turbulence the orthogonality between OAM states is no longer preserved. We will show that in combination with LDPC codes, the OAM-based modulation schemes can operate even under strong atmospheric turbulence regime. In addition, the spectral efficiency of proposed scheme is N2/log₂N times better than that of PPM.

Continuous reduction of cyclic adsorbed and desorbed NO(x) in diesel emission using nonthermal plasma.

PubMed

Kuwahara, Takuya; Nakaguchi, Harunobu; Kuroki, Tomoyuki; Okubo, Masaaki

2016-05-05

Considering the recent stringent regulations governing diesel NO(x) emission, an aftertreatment system for the reduction of NO(x) in the exhaust gas has been proposed and studied. The proposed system is a hybrid method combining nonthermal plasma and NOx adsorbent. The system does not require precious metal catalysts or harmful chemicals such as urea and ammonia. In the present system, NO(x) in diesel emission is treated by adsorption and desorption by adsorbent as well as nonthermal plasma reduction. In addition, the remaining NO(x) in the adsorbent is desorbed again in the supplied air by residual heat. The desorbed NO(x) in air recirculates into the intake of the engine, and this process, i.e., exhaust gas components' recirculation (EGCR) achieves NO(x) reduction. Alternate utilization of two adsorption chambers in the system can achieve high-efficiency NO(x) removal continuously. An experiment with a stationary diesel engine for electric power generation demonstrates an energy efficiency of 154 g(NO2)/kWh for NO(x) removal and continuous NO(x) reduction of 70.3%. Considering the regulation against diesel emission in Japan, i.e., the new regulation to be imposed on vehicles of 3.5-7.5 ton since 2016, the present aftertreatment system fulfills the requirement with only 1.0% of engine power. Copyright © 2016. Published by Elsevier B.V.

Using airborne HIAPER Pole-to-Pole Observations (HIPPO) to evaluate model and remote sensing estimates of atmospheric carbon dioxide

NASA Astrophysics Data System (ADS)

Frankenberg, Christian; Kulawik, Susan S.; Wofsy, Steven C.; Chevallier, Frédéric; Daube, Bruce; Kort, Eric A.; O'Dell, Christopher; Olsen, Edward T.; Osterman, Gregory

2016-06-01

In recent years, space-borne observations of atmospheric carbon dioxide (CO2) have been increasingly used in global carbon-cycle studies. In order to obtain added value from space-borne measurements, they have to suffice stringent accuracy and precision requirements, with the latter being less crucial as it can be reduced by just enhanced sample size. Validation of CO2 column-averaged dry air mole fractions (XCO2) heavily relies on measurements of the Total Carbon Column Observing Network (TCCON). Owing to the sparseness of the network and the requirements imposed on space-based measurements, independent additional validation is highly valuable. Here, we use observations from the High-Performance Instrumented Airborne Platform for Environmental Research (HIAPER) Pole-to-Pole Observations (HIPPO) flights from 01/2009 through 09/2011 to validate CO2 measurements from satellites (Greenhouse Gases Observing Satellite - GOSAT, Thermal Emission Sounder - TES, Atmospheric Infrared Sounder - AIRS) and atmospheric inversion models (CarbonTracker CT2013B, Monitoring Atmospheric Composition and Climate (MACC) v13r1). We find that the atmospheric models capture the XCO2 variability observed in HIPPO flights very well, with correlation coefficients (r2) of 0.93 and 0.95 for CT2013B and MACC, respectively. Some larger discrepancies can be observed in profile comparisons at higher latitudes, in particular at 300 hPa during the peaks of either carbon uptake or release. These deviations can be up to 4 ppm and hint at misrepresentation of vertical transport. Comparisons with the GOSAT satellite are of comparable quality, with an r2 of 0.85, a mean bias μ of -0.06 ppm, and a standard deviation σ of 0.45 ppm. TES exhibits an r2 of 0.75, μ of 0.34 ppm, and σ of 1.13 ppm. For AIRS, we find an r2 of 0.37, μ of 1.11 ppm, and σ of 1.46 ppm, with latitude-dependent biases. For these comparisons at least 6, 20, and 50 atmospheric soundings have been averaged for GOSAT, TES, and AIRS, respectively. Overall, we find that GOSAT soundings over the remote Pacific Ocean mostly meet the stringent accuracy requirements of about 0.5 ppm for space-based CO2 observations.

JWST ISIM Distortion Analysis Challenge

NASA Technical Reports Server (NTRS)

Cifie, Emmanuel; Matzinger, Liz; Kuhn, Jonathan; Fan, Terry

2004-01-01

Very tight distortion requirements are imposed on the JWST's ISM structure due to the sensitivity of the telescope's mirror segment and science instrument positioning. The ISIM structure is a three dimensional truss with asymmetric gusseting and metal fittings. One of the primary challenges for ISIM's analysis team is predicting the thermal distortion of the structure both from the bulk cooldown from ambient to cryo, and the smaller temperature changes within the cryogenic operating environment. As a first cut to estimate thermal distortions, a finite element model of bar elements was created. Elements representing joint areas and metal fittings use effective properties that match the behavior of the stack-up of the composite tube, gusset and adhesive under mechanical and thermal loads. These properties were derived by matching tip deflections of a solid model simplified T-joint. Because of the structure s asymmetric gusseting, this effective property model is a first attempt at predicting rotations that cannot be captured with a smeared CTE approach. In addition to the finite element analysis, several first order calculations have been performed to gauge the feasibility of the material design. Because of the stringent thermal distortion requirements at cryogenic temperatures, a composite tube material with near zero or negative CTE is required. A preliminary hand analysis of the contribution of the various components along the distortion path between FGS and the other instruments, neglecting second order effects were examined. A plot of bounding tube longitudinal and transverse CTEs for thermal stability requirements was generated to help determine the feasibility of meeting these requirements. This analysis is a work in progress en route to a large degree of freedom hi-fidelity FEA model for distortion analysis. Methods of model reduction, such as superelements, are currently being investigated.

A model with isospin doublet U(1)D gauge symmetry

NASA Astrophysics Data System (ADS)

Nomura, Takaaki; Okada, Hiroshi

2018-05-01

We propose a model with an extra isospin doublet U(1)D gauge symmetry, in which we introduce several extra fermions with odd parity under a discrete Z2 symmetry in order to cancel the gauge anomalies out. A remarkable issue is that we impose nonzero U(1)D charge to the Standard Model Higgs, and it gives the most stringent constraint to the vacuum expectation value of a scalar field breaking the U(1)D symmetry that is severer than the LEP bound. We then explore relic density of a Majorana dark matter candidate without conflict of constraints from lepton flavor violating processes. A global analysis is carried out to search for parameters which can accommodate with the observed data.

Non-Gaussianities in multifield DBI inflation with a waterfall phase transition

NASA Astrophysics Data System (ADS)

Kidani, Taichi; Koyama, Kazuya; Mizuno, Shuntaro

2012-10-01

We study multifield Dirac-Born-Infeld (DBI) inflation models with a waterfall phase transition. This transition happens for a D3 brane moving in the warped conifold if there is an instability along angular directions. The transition converts the angular perturbations into the curvature perturbation. Thanks to this conversion, multifield models can evade the stringent constraints that strongly disfavor single field ultraviolet (UV) DBI inflation models in string theory. We explicitly demonstrate that our model satisfies current observational constraints on the spectral index and equilateral non-Gaussianity as well as the bound on the tensor to scalar ratio imposed in string theory models. In addition, we show that large local type non-Gaussianity is generated together with equilateral non-Gaussianity in this model.

Development of sensor augmented robotic weld systems for aerospace propulsion system fabrication

NASA Technical Reports Server (NTRS)

Jones, C. S.; Gangl, K. J.

1986-01-01

In order to meet stringent performance goals for power and reuseability, the Space Shuttle Main Engine was designed with many complex, difficult welded joints that provide maximum strength and minimum weight. To this end, the SSME requires 370 meters of welded joints. Automation of some welds has improved welding productivity significantly over manual welding. Application has previously been limited by accessibility constraints, requirements for complex process control, low production volumes, high part variability, and stringent quality requirements. Development of robots for welding in this application requires that a unique set of constraints be addressed. This paper shows how robotic welding can enhance production of aerospace components by addressing their specific requirements. A development program at the Marshall Space Flight Center combining industrial robots with state-of-the-art sensor systems and computer simulation is providing technology for the automation of welds in Space Shuttle Main Engine production.

EMI Performance of the AIRS Cooler and Electronics

NASA Technical Reports Server (NTRS)

Johnson, D.; Collins, S.; Ross, R.

1998-01-01

The TRW pulse tube cryocooler for JPL's Atmospheric Infrared Sounder (AIRS) instrument is required to meet stringent requirements for radiated electric and magnetic fields, conducted emissions on the input power bus, and electromagnetic susceptivility.

14 CFR 120.207 - Other requirements imposed by employers.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AND ALCOHOL TESTING PROGRAM Alcohol Testing Program Requirements § 120.207 Other requirements imposed by employers. Except as expressly provided in these alcohol testing requirements, nothing in this subpart shall be construed to affect the authority of employers, or the rights of employees, with respect...

14 CFR 120.207 - Other requirements imposed by employers.

Code of Federal Regulations, 2012 CFR

2012-01-01

... AND ALCOHOL TESTING PROGRAM Alcohol Testing Program Requirements § 120.207 Other requirements imposed by employers. Except as expressly provided in these alcohol testing requirements, nothing in this subpart shall be construed to affect the authority of employers, or the rights of employees, with respect...

14 CFR 120.207 - Other requirements imposed by employers.

Code of Federal Regulations, 2013 CFR

2013-01-01

... AND ALCOHOL TESTING PROGRAM Alcohol Testing Program Requirements § 120.207 Other requirements imposed by employers. Except as expressly provided in these alcohol testing requirements, nothing in this subpart shall be construed to affect the authority of employers, or the rights of employees, with respect...

14 CFR 120.207 - Other requirements imposed by employers.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AND ALCOHOL TESTING PROGRAM Alcohol Testing Program Requirements § 120.207 Other requirements imposed by employers. Except as expressly provided in these alcohol testing requirements, nothing in this subpart shall be construed to affect the authority of employers, or the rights of employees, with respect...

14 CFR 120.207 - Other requirements imposed by employers.

Code of Federal Regulations, 2014 CFR

2014-01-01

... AND ALCOHOL TESTING PROGRAM Alcohol Testing Program Requirements § 120.207 Other requirements imposed by employers. Except as expressly provided in these alcohol testing requirements, nothing in this subpart shall be construed to affect the authority of employers, or the rights of employees, with respect...

Flight Hardware Packaging Design for Stringent EMC Radiated Emission Requirements

NASA Technical Reports Server (NTRS)

Lortz, Charlene L.; Huang, Chi-Chien N.; Ravich, Joshua A.; Steiner, Carl N.

2013-01-01

This packaging design approach can help heritage hardware meet a flight project's stringent EMC radiated emissions requirement. The approach requires only minor modifications to a hardware's chassis and mainly concentrates on its connector interfaces. The solution is to raise the surface area where the connector is mounted by a few millimeters using a pedestal, and then wrapping with conductive tape from the cable backshell down to the surface-mounted connector. This design approach has been applied to JPL flight project subsystems. The EMC radiated emissions requirements for flight projects can vary from benign to mission critical. If the project's EMC requirements are stringent, the best approach to meet EMC requirements would be to design an EMC control program for the project early on and implement EMC design techniques starting with the circuit board layout. This is the ideal scenario for hardware that is built from scratch. Implementation of EMC radiated emissions mitigation techniques can mature as the design progresses, with minimal impact to the design cycle. The real challenge exists for hardware that is planned to be flown following a built-to-print approach, in which heritage hardware from a past project with a different set of requirements is expected to perform satisfactorily for a new project. With acceptance of heritage, the design would already be established (circuit board layout and components have already been pre-determined), and hence any radiated emissions mitigation techniques would only be applicable at the packaging level. The key is to take a heritage design with its known radiated emissions spectrum and repackage, or modify its chassis design so that it would have a better chance of meeting the new project s radiated emissions requirements.

Magnetostrictive valve

NASA Technical Reports Server (NTRS)

Casabianca, C. C.

1978-01-01

Device requires no moving parts and has less stringent tolerances. Device uses magnetostrictive powdered metal and electromagnets, rather than solenoid. Device is more reliable than conventional valves.

Rural considerations in establishing network adequacy standards for qualified health plans in state and regional health insurance exchanges.

PubMed

Talbot, Jean A; Coburn, Andrew; Croll, Zach; Ziller, Erika

2013-06-01

The Affordable Care Act (ACA) requires Health Insurance Exchanges (HIEs) to specify network adequacy standards for the Qualified Health Plans (QHPs) they offer to consumers. This article examines rural issues surrounding network adequacy standards, and offers recommendations for crafting standards that optimize rural access. This policy analysis reviews ACA requirements for QHP network adequacy standards, considering Medicaid managed care and Medicare Advantage (MA) standards as models. We analyze the implications of stringent vs flexible access standards in terms of how choices might affect health plans' participation in rural markets and rural enrollees' access to care. Finally, we propose strategies for designing standards with the degree of flexibility most likely to benefit rural consumers. A traditional approach to safeguarding rural access is to impose strict network adequacy standards on plans in rural areas. However, if strict standards prove difficult to meet due to rural provider scarcity, they might diminish QHPs' willingness to serve rural areas. Thus, they could exacerbate rather than alleviate rural access problems. To benefit rural communities, network adequacy standards must be strong enough to provide real protections for beneficiaries, yet flexible enough to accommodate rural delivery system constraints and remain attainable for QHPs. Useful strategies to achieve this balance might include: adjusting standards according to degrees of rurality and rural utilization norms; counting midlevel clinicians toward fulfillment of patient-provider ratios; and allowing plans to ensure rural access through delivery system innovations such as telehealth. © 2013 National Rural Health Association.

Strategic parenting, birth order, and school performance.

PubMed

Hotz, V Joseph; Pantano, Juan

2015-10-01

Fueled by new evidence, there has been renewed interest about the effects of birth order on human capital accumulation. The underlying causal mechanisms for such effects remain unsettled. We consider a model in which parents impose more stringent disciplinary environments in response to their earlier-born children's poor performance in school in order to deter such outcomes for their later-born offspring. We provide robust empirical evidence that school performance of children in the National Longitudinal Study Children (NLSY-C) declines with birth order as does the stringency of their parents' disciplinary restrictions. When asked how they will respond if a child brought home bad grades, parents state that they would be less likely to punish their later-born children. Taken together, these patterns are consistent with a reputation model of strategic parenting.

Strategic parenting, birth order, and school performance

PubMed Central

Pantano, Juan

2015-01-01

Fueled by new evidence, there has been renewed interest about the effects of birth order on human capital accumulation. The underlying causal mechanisms for such effects remain unsettled. We consider a model in which parents impose more stringent disciplinary environments in response to their earlier-born children’s poor performance in school in order to deter such outcomes for their later-born offspring. We provide robust empirical evidence that school performance of children in the National Longitudinal Study Children (NLSY-C) declines with birth order as does the stringency of their parents’ disciplinary restrictions. When asked how they will respond if a child brought home bad grades, parents state that they would be less likely to punish their later-born children. Taken together, these patterns are consistent with a reputation model of strategic parenting. PMID:26366045

Did prohibition really work? Alcohol prohibition as a public health innovation.

PubMed

Blocker, Jack S

2006-02-01

The conventional view that National Prohibition failed rests upon an historically flimsy base. The successful campaign to enact National Prohibition was the fruit of a century-long temperance campaign, experience of which led prohibitionists to conclude that a nationwide ban on alcohol was the most promising of the many strategies tried thus far. A sharp rise in consumption during the early 20th century seemed to confirm the bankruptcy of alternative alcohol-control programs. The stringent prohibition imposed by the Volstead Act, however, represented a more drastic action than many Americans expected. Nevertheless, National Prohibition succeeded both in lowering consumption and in retaining political support until the onset of the Great Depression altered voters' priorities. Repeal resulted more from this contextual shift than from characteristics of the innovation itself.

26 CFR 1.857-4 - Tax imposed by reason of the failure to meet certain source-of-income requirements.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES Real Estate Investment Trusts § 1.857-4 Tax imposed by reason of the failure to meet certain source-of-income requirements. Section 857... 26 Internal Revenue 9 2010-04-01 2010-04-01 false Tax imposed by reason of the failure to meet...

Generalized Friedberg-Lee model for CP violation in neutrino physics

NASA Astrophysics Data System (ADS)

Razzaghi, N.; Gousheh, S. S.

2012-09-01

We propose a phenomenological model of Dirac neutrino mass operator based on the Friedberg-Lee neutrino mass model to include CP violation. By considering the most general set of complex coefficients, and imposing the condition that the mass eigenvalues are real, we find a neutrino mass matrix which is non-Hermitian, symmetric, and magic. In particular, we find that the requirement of obtaining real mass eigenvalues by transferring the residual phases to the mass eigenstates self-consistently dictates the following relationship between the imaginary part of the mass matrix elements B and the parameters of the Friedberg-Lee model: B=±(3)/(4)(a-br)2sin⁡22θ13cos⁡2θ12. We obtain inverted neutrino mass hierarchy m3=0. Making a correspondence between our model and the experimental data produces stringent conditions on the parameters as follows: 35.06°≲θ12≲36.27°, θ23=45°, 7.27°≲θ13≲11.09°, and 82.03°≲δ≲85.37°. We get mildly broken μ-τ symmetry, which reduces the resultant neutrino mixing pattern from tri-bimaximal to trimaximal. The CP violation as measured by the Jarlskog parameter is restricted by 0.027≲J≲0.044.

Nuclear Tools For Oilfield Logging-While-Drilling Applications

NASA Astrophysics Data System (ADS)

Reijonen, Jani

2011-06-01

Schlumberger is an international oilfield service company with nearly 80,000 employees of 140 nationalities, operating globally in 80 countries. As a market leader in oilfield services, Schlumberger has developed a suite of technologies to assess the downhole environment, including, among others, electromagnetic, seismic, chemical, and nuclear measurements. In the past 10 years there has been a radical shift in the oilfield service industry from traditional wireline measurements to logging-while-drilling (LWD) analysis. For LWD measurements, the analysis is performed and the instruments are operated while the borehole is being drilled. The high temperature, high shock, and extreme vibration environment of LWD imposes stringent requirements for the devices used in these applications. This has a significant impact on the design of the components and subcomponents of a downhole tool. Another significant change in the past few years for nuclear-based oilwell logging tools is the desire to replace the sealed radioisotope sources with active, electronic ones. These active radiation sources provide great benefits compared to the isotopic sources, ranging from handling and safety to nonproliferation and well contamination issues. The challenge is to develop electronic generators that have a high degree of reliability for the entire lifetime of a downhole tool. LWD tool testing and operations are highlighted with particular emphasis on electronic radiation sources and nuclear detectors for the downhole environment.

Subsonic Jet Noise Reduced With Improved Internal Exhaust Gas Mixers

NASA Technical Reports Server (NTRS)

1996-01-01

Aircraft noise pollution is becoming a major environmental concern for the world community. The Federal Aviation Administration (FAA) is responding to this concern by imposing more stringent noise restrictions for aircraft certification then ever before to keep the U.S. industry competitive with the rest of the world. At the NASA Lewis Research Center, attempts are underway to develop noise-reduction technology for newer engines and for retrofitting existing engines so that they are as quiet as (or quieter than) required. Lewis conducted acoustic and Laser Doppler Velocimetry (LDV) tests using Pratt & Whitney's Internal Exhaust Gas Mixers (IEGM). The IEGM's mix the core flow with the fan flow prior to their common exhaust. All tests were conducted in Lewis' Aero-Acoustic Propulsion Laboratory--a semihemispheric dome open to the ambient atmosphere. This was the first time Laser Doppler Velocimetry was used in such a facility at Lewis. Jet exhaust velocity and turbulence and the internal velocity fields were detailed. Far-field acoustics were also measured. Pratt & Whitney provided 1/7th scale model test hardware (a 12-lobe mixer, a 20-lobe mixer, and a splitter) for 1.7 bypass ratio engines, and NASA provided the research engineers, test facility, and test time. The Pratt & Whitney JT8D-200 engine power conditions were used for all tests.

Thermo-mechanical Design Methodology for ITER Cryodistribution cold boxes

NASA Astrophysics Data System (ADS)

Shukla, Vinit; Patel, Pratik; Das, Jotirmoy; Vaghela, Hitensinh; Bhattacharya, Ritendra; Shah, Nitin; Choukekar, Ketan; Chang, Hyun-Sik; Sarkar, Biswanath

2017-04-01

The ITER cryo-distribution (CD) system is in charge of proper distribution of the cryogen at required mass flow rate, pressure and temperature level to the users; namely the superconducting (SC) magnets and cryopumps (CPs). The CD system is also capable to use the magnet structures as a thermal buffer in order to operate the cryo-plant as much as possible at a steady state condition. A typical CD cold box is equipped with mainly liquid helium (LHe) bath, heat exchangers (HX’s), cryogenic valves, filter, heaters, cold circulator, cold compressor and process piping. The various load combinations which are likely to occur during the life cycle of the CD cold boxes are imposed on the representative model and impacts on the system are analyzed. This study shows that break of insulation vacuum during nominal operation (NO) along with seismic event (Seismic Level-2) is the most stringent load combination having maximum stress of 224 MPa. However, NO+SMHV (Séismes Maximaux Historiquement Vraisemblables = Maximum Historically Probable Earthquakes) load combination is having the least safety margin and will lead the basis of the design of the CD system and its sub components. This paper presents and compares the results of different load combinations which are likely to occur on a typical CD cold box.

An Aircraft Separation Algorithm with Feedback and Perturbation

NASA Technical Reports Server (NTRS)

White, Allan L.

2010-01-01

A separation algorithm is a set of rules that tell aircraft how to maneuver in order to maintain a minimum distance between them. This paper investigates demonstrating that separation algorithms satisfy the FAA requirement for the occurrence of incidents by means of simulation. Any demonstration that a separation algorithm, or any other aspect of flight, satisfies the FAA requirement is a challenge because of the stringent nature of the requirement and the complexity of airspace operations. The paper begins with a probability and statistical analysis of both the FAA requirement and demonstrating meeting it by a Monte Carlo approach. It considers the geometry of maintaining separation when one plane must change its flight path. It then develops a simple feedback control law that guides the planes on their paths. The presence of feedback control permits the introduction of perturbations, and the stochastic nature of the chosen perturbation is examined. The simulation program is described. This paper is an early effort in the realistic demonstration of a stringent requirement. Much remains to be done.

Work Hours Assessment and Monitoring Initiative (WHAMI) under resident direction: a strategy for working within limitations.

PubMed

Goldstein, Michael J; Samstein, Benjamin; Ude, Akuo; Widmann, Warren D; Hardy, Mark A

2005-01-01

A review of surgical residents' duty-hours prompted a Work Hours Assessment and Monitoring Initiative (WHAMI) that preemptively limits residents from violating "duty-hours rules." Work hours data for the Department of Surgery were reviewed over 8-months at New York Presbyterian Hospital-Columbia Campus. This ongoing review is performed by a work-hours monitoring team, which supervises residents' hours for the initial 5-days of each week. As residents approach work-hours limits for the week, they are dismissed from duty for appropriate time periods in the remaining 2 days of the week. The work-hours data entry compliance for 52 residents was increased from 93% to 99% after creation of the WHAMI. Before the new system, a mean of 9.5 residents per month (19%) worked an average of 7.3 +/- 6.4 hours over the 80-hour limit. Averaged monthly compliance with the 80-hour work limit was increased to 98% with introduction of the WHAMI. A review of on-call duty hours revealed a mean of 7 (14%) residents per month who worked an average of 2.4 hours beyond 24-hour call limitations including "sign-out" time imposed by the ACGME. New monitoring procedures have improved compliance to 100% with 24-hour call limitations imposed by the ACGME. Compliance with the more stringent New York State (NYS) guidelines has approached 94% with noncompliant residents extending on-call hours by an average of 1.5 hours over the 24-hour limitations, most on "off General Surgery" rotations or out-of-state rotations. Review of mandatory rest periods contributed to an increase in mean "time off" between work periods, thereby increasing compliance with ACGME guidelines and NYS regulations from 75% to 88%, and 90% to 98%, respectively. Residents reporting less than 10 hours rest reported increased "time off" from 6.2 +/- 2.0 to 7.9 +/- 1.3 hours (p < 0.001). Internal review of surgical resident's duty-hours at a large university hospital revealed that despite strict scheduling and the requirement of mandatory duty-hours entry, achieving the goals of meeting the duty-hours requirements and of ongoing data entry required the creation of a resident enforced, real-time Work Hours Assessment and Monitoring Initiative.

30 CFR 810.4 - Responsibility.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PERMANENT PROGRAM...) The Director shall ensure that performance standards and design requirements at least as stringent as... State regulatory authority shall ensure that performance standards and design requirements at least as...

Self consistency grouping: a stringent clustering method

PubMed Central

2012-01-01

Background Numerous types of clustering like single linkage and K-means have been widely studied and applied to a variety of scientific problems. However, the existing methods are not readily applicable for the problems that demand high stringency. Methods Our method, self consistency grouping, i.e. SCG, yields clusters whose members are closer in rank to each other than to any member outside the cluster. We do not define a distance metric; we use the best known distance metric and presume that it measures the correct distance. SCG does not impose any restriction on the size or the number of the clusters that it finds. The boundaries of clusters are determined by the inconsistencies in the ranks. In addition to the direct implementation that finds the complete structure of the (sub)clusters we implemented two faster versions. The fastest version is guaranteed to find only the clusters that are not subclusters of any other clusters and the other version yields the same output as the direct implementation but does so more efficiently. Results Our tests have demonstrated that SCG yields very few false positives. This was accomplished by introducing errors in the distance measurement. Clustering of protein domain representatives by structural similarity showed that SCG could recover homologous groups with high precision. Conclusions SCG has potential for finding biological relationships under stringent conditions. PMID:23320864

Constraining neutrino mass from neutrinoless double beta decay

NASA Astrophysics Data System (ADS)

Dev, P. S. Bhupal; Goswami, Srubabati; Mitra, Manimala; Rodejohann, Werner

2013-11-01

We study the implications of the recent results on neutrinoless double beta decay (0νββ) from GERDA-I (Ge76) and KamLAND-Zen+EXO-200 (Xe136) and the upper limit on the sum of light neutrino masses from Planck. We show that the upper limits on the effective neutrino mass from Xe136 are stronger than those from Ge76 for most of the recent calculations of the nuclear matrix elements (NMEs). We also analyze the compatibility of these limits with the claimed observation in Ge76 and show that while the updated claim value is still compatible with the recent GERDA limit as well as the individual Xe136 limits for a few NME calculations, it is inconsistent with the combined Xe136 limit for all but one NME. Imposing the most stringent limit from Planck, we find that the canonical light neutrino contribution cannot saturate the current limit, irrespective of the NME uncertainties. Saturation can be reached by inclusion of the right-handed (RH) neutrino contributions in TeV-scale left-right symmetric models with type-II seesaw. This imposes a lower limit on the lightest neutrino mass. Using the 0νββ bounds, we also derive correlated constraints in the RH sector, complimentary to those from direct searches at the LHC.

Role of the Stringent Stress Response in the Antibiotic Resistance Phenotype of Methicillin-Resistant Staphylococcus aureus

PubMed Central

Aedo, Sandra

2016-01-01

Resistance to beta-lactam antibiotics in methicillin-resistant Staphylococcus aureus (MRSA) requires the presence of an acquired genetic determinant, mecA or mecC, which encode penicillin-binding protein PBP2A or PBP2A′, respectively. Although all MRSA strains share a mechanism of resistance, the phenotypic expression of beta-lactam resistance shows considerable strain-to-strain variation. The stringent stress response, a stress response that results from nutrient limitation, was shown to play a key role in determining the resistance level of an MRSA strain. In the present study, we validated the impact of the stringent stress response on transcription and translation of mecA in the MRSA clinical isolate strain N315, which also carries known regulatory genes (mecI/mecR1/mecR2 and blaI/blaR1) for mecA transcription. We showed that the impact of the stringent stress response on the resistance level may be restricted to beta-lactam resistance based on a “foreign” determinant such as mecA, as opposed to resistance based on mutations in the native S. aureus determinant pbpB (encoding PBP2). Our observations demonstrate that high-level resistance mediated by the stringent stress response follows the current model of beta-lactam resistance in which the native PBP2 protein is also essential for expression of the resistance phenotype. We also show that the Staphylococcus sciuri pbpD gene (also called mecAI), the putative evolutionary precursor of mecA, confers oxacillin resistance in an S. aureus strain, generating a heterogeneous phenotype that can be converted to high and homogenous resistance by induction of the stringent stress response in the bacteria. PMID:26833147

Environmental Life Cycle Assessment and Cost Analysis of Bath, NY Wastewater Treatment Plant: Potential Upgrade Implications

EPA Science Inventory

Many communities across the U.S. are required to upgrade wastewater treatment plants (WWTP) to meet increasingly stringent nutrient effluent standards. However, increased capital, energy and chemical requirements of upgrades create potential trade-offs between eutrophication pot...

Autonomous Control of Space Nuclear Reactors

NASA Technical Reports Server (NTRS)

Merk, John

2013-01-01

Nuclear reactors to support future robotic and manned missions impose new and innovative technological requirements for their control and protection instrumentation. Long-duration surface missions necessitate reliable autonomous operation, and manned missions impose added requirements for failsafe reactor protection. There is a need for an advanced instrumentation and control system for space-nuclear reactors that addresses both aspects of autonomous operation and safety. The Reactor Instrumentation and Control System (RICS) consists of two functionally independent systems: the Reactor Protection System (RPS) and the Supervision and Control System (SCS). Through these two systems, the RICS both supervises and controls a nuclear reactor during normal operational states, as well as monitors the operation of the reactor and, upon sensing a system anomaly, automatically takes the appropriate actions to prevent an unsafe or potentially unsafe condition from occurring. The RPS encompasses all electrical and mechanical devices and circuitry, from sensors to actuation device output terminals. The SCS contains a comprehensive data acquisition system to measure continuously different groups of variables consisting of primary measurement elements, transmitters, or conditioning modules. These reactor control variables can be categorized into two groups: those directly related to the behavior of the core (known as nuclear variables) and those related to secondary systems (known as process variables). Reliable closed-loop reactor control is achieved by processing the acquired variables and actuating the appropriate device drivers to maintain the reactor in a safe operating state. The SCS must prevent a deviation from the reactor nominal conditions by managing limitation functions in order to avoid RPS actions. The RICS has four identical redundancies that comply with physical separation, electrical isolation, and functional independence. This architecture complies with the safety requirements of a nuclear reactor and provides high availability to the host system. The RICS is intended to interface with a host computer (the computer of the spacecraft where the reactor is mounted). The RICS leverages the safety features inherent in Earth-based reactors and also integrates the wide range neutron detector (WRND). A neutron detector provides the input that allows the RICS to do its job. The RICS is based on proven technology currently in use at a nuclear research facility. In its most basic form, the RICS is a ruggedized, compact data-acquisition and control system that could be adapted to support a wide variety of harsh environments. As such, the RICS could be a useful instrument outside the scope of a nuclear reactor, including military applications where failsafe data acquisition and control is required with stringent size, weight, and power constraints.

Optical sectioning microscopy using two-frame structured illumination and Hilbert-Huang data processing

NASA Astrophysics Data System (ADS)

Trusiak, M.; Patorski, K.; Tkaczyk, T.

2014-12-01

We propose a fast, simple and experimentally robust method for reconstructing background-rejected optically-sectioned microscopic images using two-shot structured illumination approach. Innovative data demodulation technique requires two grid-illumination images mutually phase shifted by π (half a grid period) but precise phase displacement value is not critical. Upon subtraction of the two frames the input pattern with increased grid modulation is computed. The proposed demodulation procedure comprises: (1) two-dimensional data processing based on the enhanced, fast empirical mode decomposition (EFEMD) method for the object spatial frequency selection (noise reduction and bias term removal), and (2) calculating high contrast optically-sectioned image using the two-dimensional spiral Hilbert transform (HS). The proposed algorithm effectiveness is compared with the results obtained for the same input data using conventional structured-illumination (SIM) and HiLo microscopy methods. The input data were collected for studying highly scattering tissue samples in reflectance mode. In comparison with the conventional three-frame SIM technique we need one frame less and no stringent requirement on the exact phase-shift between recorded frames is imposed. The HiLo algorithm outcome is strongly dependent on the set of parameters chosen manually by the operator (cut-off frequencies for low-pass and high-pass filtering and η parameter value for optically-sectioned image reconstruction) whereas the proposed method is parameter-free. Moreover very short processing time required to efficiently demodulate the input pattern predestines proposed method for real-time in-vivo studies. Current implementation completes full processing in 0.25s using medium class PC (Inter i7 2,1 GHz processor and 8 GB RAM). Simple modification employed to extract only first two BIMFs with fixed filter window size results in reducing the computing time to 0.11s (8 frames/s).

Developing Performance Estimates for High Precision Astrometry with TMT

NASA Astrophysics Data System (ADS)

Schoeck, Matthias; Do, Tuan; Ellerbroek, Brent; Herriot, Glen; Meyer, Leo; Suzuki, Ryuji; Wang, Lianqi; Yelda, Sylvana

2013-12-01

Adaptive optics on Extremely Large Telescopes will open up many new science cases or expand existing science into regimes unattainable with the current generation of telescopes. One example of this is high-precision astrometry, which has requirements in the range from 10 to 50 micro-arc-seconds for some instruments and science cases. Achieving these requirements imposes stringent constraints on the design of the entire observatory, but also on the calibration procedures, observing sequences and the data analysis techniques. This paper summarizes our efforts to develop a top down astrometry error budget for TMT. It is predominantly developed for the first-light AO system, NFIRAOS, and the IRIS instrument, but many terms are applicable to other configurations as well. Astrometry error sources are divided into 5 categories: Reference source and catalog errors, atmospheric refraction correction errors, other residual atmospheric effects, opto-mechanical errors and focal plane measurement errors. Results are developed in parametric form whenever possible. However, almost every error term in the error budget depends on the details of the astrometry observations, such as whether absolute or differential astrometry is the goal, whether one observes a sparse or crowded field, what the time scales of interest are, etc. Thus, it is not possible to develop a single error budget that applies to all science cases and separate budgets are developed and detailed for key astrometric observations. Our error budget is consistent with the requirements for differential astrometry of tens of micro-arc-seconds for certain science cases. While no show stoppers have been found, the work has resulted in several modifications to the NFIRAOS optical surface specifications and reference source design that will help improve the achievable astrometry precision even further.

Trajectory optimization study of a lifting body re-entry vehicle for medium to intermediate range applications

NASA Astrophysics Data System (ADS)

Rizvi, S. Tauqeer ul Islam; Linshu, He; ur Rehman, Tawfiq; Rafique, Amer Farhan

2012-11-01

A numerical optimization study of lifting body re-entry vehicles is presented for nominal as well as shallow entry conditions for Medium and Intermediate Range applications. Due to the stringent requirement of a high degree of accuracy for conventional vehicles, lifting re-entry can be used to attain the impact at the desired terminal flight path angle and speed and thus can potentially improve accuracy of the re-entry vehicle. The re-entry of a medium range and intermediate range vehicles is characterized by very high negative flight path angle and low re-entry speed as compared to a maneuverable re-entry vehicle or a common aero vehicle intended for an intercontinental range. Highly negative flight path angles at the re-entry impose high dynamic pressure as well as heat loads on the vehicle. The trajectory studies are carried out to maximize the cross range of the re-entry vehicle while imposing a maximum dynamic pressure constraint of 350 KPa with a 3 MW/m2 heat rate limit. The maximum normal acceleration and the total heat load experienced by the vehicle at the stagnation point during the maneuver have been computed for the vehicle for possible future conceptual design studies. It has been found that cross range capability of up to 35 km can be achieved with a lifting-body design within the heat rate and the dynamic pressure boundary at normal entry conditions. For shallow entry angle of -20 degree and intermediate ranges a cross range capability of up to 250 km can be attained for a lifting body design with less than 10 percent loss in overall range. The normal acceleration also remains within limits. The lifting-body results have also been compared with wing-body results at shallow entry condition. An hp-adaptive pseudo-spectral method has been used for constrained trajectory optimization.

40 CFR 63.2241 - What are the work practice requirements and how must I meet them?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Products Compliance Options, Operating Requirements, and Work Practice Requirements § 63.2241 What are the...) If you have a dry rotary dryer, you may choose to designate your dry rotary dryer as a green rotary dryer and meet the more stringent compliance options and operating requirements in § 63.2240 for green...

Gravitational wave emission from oscillating millisecond pulsars

NASA Astrophysics Data System (ADS)

Alford, Mark G.; Schwenzer, Kai

2015-02-01

Neutron stars undergoing r-mode oscillation emit gravitational radiation that might be detected on the Earth. For known millisecond pulsars the observed spin-down rate imposes an upper limit on the possible gravitational wave signal of these sources. Taking into account the physics of r-mode evolution, we show that only sources spinning at frequencies above a few hundred Hertz can be unstable to r-modes, and we derive a more stringent universal r-mode spin-down limit on their gravitational wave signal. We find that this refined bound limits the gravitational wave strain from millisecond pulsars to values below the detection sensitivity of next generation detectors. Young sources are therefore a more promising option for the detection of gravitational waves emitted by r-modes and to probe the interior composition of compact stars in the near future.

Trade treaties and alcohol advertising policy.

PubMed

Gould, Ellen

2005-09-01

Restrictions on alcohol advertising are vulnerable to challenge under international trade agreements. As countries negotiate new trade treaties and expand the scope of existing ones, the risk of such a challenge increases. While alcohol advertising restrictions normally do not distinguish between foreign and domestic products, this neutral character does not protect them from being challenged under trade rules. The article analyzes four provisions of trade agreements--expropriation, de facto discrimination, market access, and necessity--in relation to the jeopardy they pose for alcohol advertising restrictions. Key cases are reviewed to illustrate how these provisions have been used to either overturn existing advertising restrictions or prevent new ones from coming into force. The article also reports on the mixed results governments have had in trying to justify their regulations to trade panels and the stringent criteria imposed for proving that a regulation is "necessary."

Multilevel DC Link Inverter for Brushless Permanent Magnet Motors with Very Low Inductance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Su, G.J.

2001-10-29

Due to their long effective air gaps, permanent magnet motors tend to have low inductance. The use of ironless stator structure in present high power PM motors (several tens of kWs) reduces the inductance even further (< 100 {micro}H). This low inductance imposes stringent current regulation demands for the inverter to obtain acceptable current ripple. An analysis of the current ripple for these low inductance brushless PM motors shows that a standard inverter with the most commonly used IGBT switching devices cannot meet the current regulation demands and will produce unacceptable current ripples due to the IGBT's limited switching frequency.more » This paper introduces a new multilevel dc link inverter, which can dramatically reduce the current ripple for brushless PM motor drives. The operating principle and design guidelines are included.« less

Testing for periodicity of extinction

NASA Technical Reports Server (NTRS)

Raup, David M.; Sepkoski, J. J., Jr.

1988-01-01

The statistical techniques used by Raup and Sepkoski (1984 and 1986) to identify a 26-Myr periodicity in the biological extinction record for the past 250 Myr are reexamined, responding in detail to the criticisms of Stigler and Wagner (1987). It is argued that evaluation of a much larger set of extinction data using a time scale with 51 sampling intervals supports the finding of periodicity. In a reply by Sigler and Wagner, the preference for a 26-Myr period is attributed to a numerical quirk in the Harland et al. (1982) time scale, in which the subinterval boundaries are not linear interpolations between the stage boundaries but have 25-Myr periodicity. It is stressed that the results of the stringent statistical tests imposed do not disprove periodicity but rather indicate that the evidence and analyses presented so far are inadequate.

Nutrient Removal and Resource Recovery: Effect on Life Cycle Cost and Environmental Impacts of Small Scale Wastewater Treatment

EPA Science Inventory

Many communities across the U.S. are required to upgrade wastewater treatment plants (WWTP) to meet increasingly stringent nutrient effluent standards. However, increased capital, energy and chemical requirements of upgrades create potential trade-offs between eutrophication pote...

40 CFR 85.525 - Applicable standards.

Code of Federal Regulations, 2012 CFR

2012-07-01

... prohibition, vehicles/engines that have been converted to operate on a different fuel must meet emission standards and related requirements as follows: (a) The modified vehicle/engine must meet the requirements that applied for the OEM vehicle/engine, or the most stringent OEM vehicle/engine standards in any...

78 FR 20039 - Reportable Events and Certain Other Notification Requirements

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-03

...'' test and four other criteria designed to measure various aspects of financial soundness. The credit... controlled group changes. Like section 4043, the reportable events regulation generally requires post-event... available for plans that could meet one of two funding tests that would be more stringent than those...

40 CFR 1039.625 - What requirements apply under the program for equipment-manufacturer flexibility?

Code of Federal Regulations, 2012 CFR

2012-07-01

... NONROAD COMPRESSION-IGNITION ENGINES Special Compliance Provisions § 1039.625 What requirements apply... manufacturers to produce equipment with engines that are subject to less stringent emission standards after the... such equipment without manufacturing it. Engines and equipment you produce under this section are...

40 CFR 1039.625 - What requirements apply under the program for equipment-manufacturer flexibility?

Code of Federal Regulations, 2013 CFR

2013-07-01

... NONROAD COMPRESSION-IGNITION ENGINES Special Compliance Provisions § 1039.625 What requirements apply... manufacturers to produce equipment with engines that are subject to less stringent emission standards after the... such equipment without manufacturing it. Engines and equipment you produce under this section are...

TriPleX: a versatile dielectric photonic platform

NASA Astrophysics Data System (ADS)

Wörhoff, Kerstin; Heideman, René G.; Leinse, Arne; Hoekman, Marcel

2015-04-01

Photonic applications based on planar waveguide technology impose stringent requirements on properties such as optical propagation losses, light coupling to optical fibers, integration density, as well as on reliability and reproducibility. The latter is correlated to a high level of control of the refractive index and waveguide geometry. In this paper, we review a versatile dielectric waveguide platform, called TriPleX, which is based on alternating silicon nitride and silicon dioxide films. Fabrication with CMOS-compatible equipment based on low-pressure chemical vapor deposition enables the realization of stable material compositions being a prerequisite to the control of waveguide properties and modal shape. The transparency window of both materials allows for the realization of low-loss waveguides over a wide wavelength range (400 nm-2.35 μm). Propagation losses as low as 5×10-4 dB/cm are reported. Three basic geometries (box shell, double stripe, and filled box) can be distinguished. A specific tapering technology is developed for on-chip, low-loss (<0.1 dB) spotsize convertors, allowing for combining efficient fiber to chip coupling with high-contrast waveguides required for increased functional complexity as well as for hybrid integration with other photonic platforms such as InP and SOI. The functionality of the TriPleX platform is captured by verified basic building blocks. The corresponding library and associated design kit is available for multi-project wafer (MPW) runs. Several applications of this platform technology in communications, biomedicine, sensing, as well as a few special fields of photonics are treated in more detail.

ARI's Views on ANSI S12.60-2002.

ERIC Educational Resources Information Center

Darbeau, Michele

2003-01-01

States the position of the Air-Conditioning and Refrigeration Institute (ARI) toward ANSI Standard 12.60, which addresses classroom acoustics. Explains why it believes the standard creates an overly stringent requirement. (EV)

Adaptive structures for precision controlled large space systems

NASA Technical Reports Server (NTRS)

Garba, John A.; Wada, Ben K.; Fanson, James L.

1991-01-01

The stringent accuracy and ground test validation requirements of some of the future space missions will require new approaches in structural design. Adaptive structures, structural systems that can vary their geometric congiguration as well as their physical properties, are primary candidates for meeting the functional requirements for such missions. Research performed in the development of such adaptive structural systems is described.

42 CFR 441.615 - Administration fee requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... SERVICES Vaccines for Children Program § 441.615 Administration fee requirements. (a) Under the VFC Program, a provider who administers a qualified pediatric vaccine to a federally vaccine-eligible child, may not impose a charge for the cost of the vaccine. (1) A provider can impose a fee for the...

Design and Proto-Flight Test Strategy for a Microscale Solar Thermal Engine

NASA Astrophysics Data System (ADS)

Kennedy, F. G.; Palmer, P.; Gibbon, D.

2002-01-01

The authors have previously shown that a micro-scale solar thermal engine, using storable monopropellants (e.g., water, ammonia, or hydrazine) and simplified subsystems, augments microsatellite capabilities by permitting velocity changes on the order of 1,500-3,000 m/s. Small satellites have long been seen as "confined" to limited roles in Low Earth Orbit (LEO). Adding significant propulsive capability opens up new roles and missions--among these, communications in geosynchronous earth orbit (GEO), as well as lunar orbit insertion and near-earth asteroid flybys. Transfer times range from as little as 30-40 days (for Geosynchronous Transfer Orbit to GEO) to 275 days for selected near-earth object encounters. This is accomplished by performing moderate thrust (~5 N) firings of the solar thermal engine at perigee and/or apogee. This paper will briefly review benchmark missions and preliminary design choices, concentrating on the selected detailed design and its ramifications for testing and spacecraft operational use. The solar thermal propulsion system is to be built as a proto-qualification/proto-flight unit (i.e., tested to qualification levels and subsequently used in on-orbit operations). This will minimize the number of experimental iterations prior to flight and reduce overall development cost. The testing program will include acoustic, sinusoidal, and random vibration tests, in line with Ariane 5's Ariane Structure for Auxiliary Payloads (ASAP) requirements. As several SSTL enhanced microsatellites have flown aboard Ariane, these figures represent excellent baseline values for the test campaign. Additionally, the solar thermal engine will be constructed so as to ensure compatibility with existing host spacecraft operational protocols. SSTL ground operations are "autonomous and self-checking," requiring the equivalent of only several operators per day to manage numerous small satellite passes. It is important that an advanced propulsion system not compromise the existing operational paradigm by requiring significantly increased oversight at the satellite ground station. Imposing significant requirements on the host satellite--stringent pointing, an added command and telemetry burden, substantial power augmentation, or severe structural modifications--could make a prima facie "useful" system worthless to the owner and/or operator. The authors will describe some of the creative solutions used to minimize these imposed requirements, simplifying the satellite designer's task. The result of this activity is a low-cost, two-year test program that is intended to result in a fully qualified flight-ready solar thermal engine, prepared for integration and launch no later than 2005. The views expressed in this article are those of the authors and do not reflect the official policy or position of the United States Air Force, Department of Defense, or the U.S. Government.

Experience in operating earth dams of the NIVA cascade of the Kola Regional Power administration constructed in 1930-1960

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nosova, O.N.; Margolina, O.G.; Sergeeva, N.S.

1995-08-01

This article discusses Russian experiences in monitoring earth-filled dams of the Niva region. These are low and medium head facilities in operation from 30 to 60 years. As shown by the experiences of long-term operation of earth structures in this area and on embankments being constructed by the method of dumping soil into water, it is necessary to impose more stringent requirements with respect to determining the steepness of these slopes to increase their stability, as is done when the structures are constructed dry. To organize successful monitoring of seepage processes in the investigated structures having substantial anisotropy of themore » soil, special recommendations of the disposition of piezometers under such specific conditions should be worked out. Recommendations on the disposition of piezometers under conditions of a noticeable effect of the groundwater regime of the surrounding territory on the seepage regime of the hydro development should be worked out accordingly. Since the calculations made in the work, as a result of which instability of many slopes was detected, are not always confirmed by practice, it is advisable to correct the method of such calculations with consideration of the characteristics of the formation of the seepage flow in the downstream shoulder of dams with pronounced anisotropy of the soil.« less

Real time testing of intelligent relays for synchronous distributed generation islanding detection

NASA Astrophysics Data System (ADS)

Zhuang, Davy

As electric power systems continue to grow to meet ever-increasing energy demand, their security, reliability, and sustainability requirements also become more stringent. The deployment of distributed energy resources (DER), including generation and storage, in conventional passive distribution feeders, gives rise to integration problems involving protection and unintentional islanding. Distributed generators need to be islanded for safety reasons when disconnected or isolated from the main feeder as distributed generator islanding may create hazards to utility and third-party personnel, and possibly damage the distribution system infrastructure, including the distributed generators. This thesis compares several key performance indicators of a newly developed intelligent islanding detection relay, against islanding detection devices currently used by the industry. The intelligent relay employs multivariable analysis and data mining methods to arrive at decision trees that contain both the protection handles and the settings. A test methodology is developed to assess the performance of these intelligent relays on a real time simulation environment using a generic model based on a real-life distribution feeder. The methodology demonstrates the applicability and potential advantages of the intelligent relay, by running a large number of tests, reflecting a multitude of system operating conditions. The testing indicates that the intelligent relay often outperforms frequency, voltage and rate of change of frequency relays currently used for islanding detection, while respecting the islanding detection time constraints imposed by standing distributed generator interconnection guidelines.

Thermal discharges from Paducah Gaseous Diffusion Plant outfalls: Impacts on stream temperatures and fauna of Little Bayou and Big Bayou Creeks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roy, W.K.; Ryon, M.G.; Hinzman, R.L.

1996-03-01

The development of a biological monitoring plan for the receiving streams of the Paducah Gaseous Diffusion Plant (PGDP) began in the late 1980s, because of an Agreed Order (AO) issued in September 1987 by the Kentucky Division of Water (KDOW). Five years later, in September 1992, more stringent effluent limitations were imposed upon the PGDP operations when the KDOW reissued Kentucky Pollutant Discharge Elimination System permit No. KY 0004049. This action prompted the US Department of Energy (DOE) to request a stay of certain limits contained in the permit. An AO is being negotiated between KDOW, the US Enrichment Corporationmore » (USEC), and DOE that will require that several studies be conducted, including this stream temperature evaluation study, in an effort to establish permit limitations. All issues associated with this AO have been resolved, and the AO is currently being signed by all parties involved. The proposed effluent temperature limit is 89 F (31.7 C) as a mean monthly temperature. In the interim, temperatures are not to exceed 95 F (35 C) as a monthly mean or 100 F (37.8 C) as a daily maximum. This study includes detailed monitoring of instream temperatures, benthic macroinvertebrate communities, fish communities, and a laboratory study of thermal tolerances.« less

Thermal Discharges from Paducah Gaseous Diffusion Plant Outfalls: Impacts on Stream Temperatures and Fauna of Little Bayou and Big Bayou Creeks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roy, W.K.

1999-01-01

The development of a biological monitoring plan for the receiving streams of the Paducah Gaseous Diffusion Plant (PGDP) began in the late 1980s, because of an Agreed Order (AO) issued in September 1987 by the Kentucky Division of Water (KDOW). Five years later, in September 1992, more stringent effluent limitations were imposed upon the PGDP operations when the KDOW reissued Kentucky Pollutant Discharge Elimination System permit No. KY 0004049. This action prompted the US Department of Energy (DOE) to request a stay of certain limits contained in the permit. An AO is being negotiated between KDOW, the United States Enrichmentmore » Corporation (USEC), and DOE that will require that several studies be conducted, including this stream temperature evaluation study, in an effort to establish permit limitations. All issues associated with this AO have been resolved, and the AO is currently being signed by all parties involved. The proposed effluent temperature limit is 89 F (31.7C) as a mean monthly temperature. In the interim, temperatures are not to exceed 95 F (35 C) as a monthly mean or 100 F (37.8 C) as a daily maximum. This study includes detailed monitoring of instream temperatures, benthic macroinvertebrate communities, fish communities, and a laboratory study of thermal tolerances.« less

Temporal and spectral characteristics of solar flare hard X-ray emission

NASA Technical Reports Server (NTRS)

Dennis, B. R.; Kiplinger, A. L.; Orwig, L. E.; Frost, K. J.

1985-01-01

Solar Maximum Mission observations of three flares that impose stringent constraints on physical models of the hard X-ray production during the impulsive phase are presented. Hard X-ray imaging observations of the flares on 1980 November 5 at 22:33 UT show two patches in the 16 to 30 keV images that are separated by 70,000 km and that brighten simultaneously to within 5 s. Observations to O V from one of the footprints show simultaneity of the brightening in this transition zone line and in the total hard X-ray flux to within a second or two. These results suggest but do not require the existence of electron beams in this flare. The rapid fluctuations of the hard X-ray flux within some flares on the time scales of 1 s also provide evidence for electron beams and limits on the time scale of the energy release mechanism. Observations of a flare on 1980 June 6 at 22:34 UT show variations in the 28 keV X-ray counting rate from one 20 ms interval to the next over a period of 10 s. The hard X-ray spectral variations measured with 128 ms time resolution for one 0.5 s spike during this flare are consistent with the predictions of thick-target non-thermal beam model.

Analysis of multiuser mixed RF/FSO relay networks for performance improvements in Cloud Computing-Based Radio Access Networks (CC-RANs)

NASA Astrophysics Data System (ADS)

Alimi, Isiaka A.; Monteiro, Paulo P.; Teixeira, António L.

2017-11-01

The key paths toward the fifth generation (5G) network requirements are towards centralized processing and small-cell densification systems that are implemented on the cloud computing-based radio access networks (CC-RANs). The increasing recognitions of the CC-RANs can be attributed to their valuable features regarding system performance optimization and cost-effectiveness. Nevertheless, realization of the stringent requirements of the fronthaul that connects the network elements is highly demanding. In this paper, considering the small-cell network architectures, we present multiuser mixed radio-frequency/free-space optical (RF/FSO) relay networks as feasible technologies for the alleviation of the stringent requirements in the CC-RANs. In this study, we use the end-to-end (e2e) outage probability, average symbol error probability (ASEP), and ergodic channel capacity as the performance metrics in our analysis. Simulation results show the suitability of deployment of mixed RF/FSO schemes in the real-life scenarios.

Development of a 10 Ah, Prismatic, Lithium-Ion Cell for NASA/GSFC

NASA Technical Reports Server (NTRS)

Stein, Brian; Baker, John W.; George, Douglas S.; Isaacs, Nathan D.; Shah, Pinakin M.; Rao, Gopalakrishna M.; Day, John H. (Technical Monitor)

2001-01-01

MSA's 10 Ah Li-ion cell is a rugged design suitable for the stringent requirements of aerospace applications. Eighteen cells demonstrate consistent cycling performance over a wide range of rates and temperatures. The cell passes qualification requirements for vibration survivability technology improvements at MSA continue to enhance cell performance.

40 CFR 1039.625 - What requirements apply under the program for equipment-manufacturer flexibility?

Code of Federal Regulations, 2014 CFR

2014-07-01

... differences that justify your request. (vi) Describe your efforts to find and use other compliant engines, or... NONROAD COMPRESSION-IGNITION ENGINES Special Compliance Provisions § 1039.625 What requirements apply... manufacturers to produce equipment with engines that are subject to less stringent emission standards after the...

40 CFR Appendix A to Part 58 - Quality Assurance Requirements for SLAMS, SPMs and PSD Air Monitoring

Code of Federal Regulations, 2010 CFR

2010-07-01

... quality system in terms of the organizational structure, functional responsibilities of management and... more stringent requirements. Monitoring organizations may, based on their quality objectives, develop... infrequent work with EPA funds may combine the QMP with the QAPP based on negotiations with the funding...

Reduced-order modeling of soft robots

PubMed Central

Chenevier, Jean; González, David; Aguado, J. Vicente; Chinesta, Francisco

2018-01-01

We present a general strategy for the modeling and simulation-based control of soft robots. Although the presented methodology is completely general, we restrict ourselves to the analysis of a model robot made of hyperelastic materials and actuated by cables or tendons. To comply with the stringent real-time constraints imposed by control algorithms, a reduced-order modeling strategy is proposed that allows to minimize the amount of online CPU cost. Instead, an offline training procedure is proposed that allows to determine a sort of response surface that characterizes the response of the robot. Contrarily to existing strategies, the proposed methodology allows for a fully non-linear modeling of the soft material in a hyperelastic setting as well as a fully non-linear kinematic description of the movement without any restriction nor simplifying assumption. Examples of different configurations of the robot were analyzed that show the appeal of the method. PMID:29470496

Effects of Internal Border Control on Spread of Pandemic Influenza

PubMed Central

Zamani, Nasim; MacIntyre, C. Raina; Becker, Niels G.

2007-01-01

We investigated the capacity of internal border control to limit influenza spread in an emergent pandemic in the context of Australia, a country with a low-population density and geopolitical boundaries that may facilitate restrictions. Mathematical models were used to study the time delay between epidemics in 2 population centers when travel restrictions were imposed. The models demonstrated that population size, travel rates, and places where travelers reside can strongly influence delay. The model simulations suggested that moderate delays in geographic spread may be possible with stringent restrictions and a low reproduction number, but results will be sensitive to the reproduction number and timing of restrictions. Model limitations include the absence of further importations and additional control measures. Internal border control may have a role in protecting domestic centers early in a pandemic, when importations are sparse. Our results may be useful for policymakers. PMID:18214176

Ratios of charged antiparticles to particles near midrapidity in Au+Au collisions at (sNN)=200 GeV

NASA Astrophysics Data System (ADS)

Back, B. B.; Baker, M. D.; Barton, D. S.; Betts, R. R.; Ballintijn, M.; Bickley, A. A.; Bindel, R.; Budzanowski, A.; Busza, W.; Carroll, A.; Decowski, M. P.; Garcia, E.; George, N.; Gulbrandsen, K.; Gushue, S.; Halliwell, C.; Hamblen, J.; Heintzelman, G. A.; Henderson, C.; Hofman, D. J.; Hollis, R. S.; Hołyński, R.; Holzman, B.; Iordanova, A.; Johnson, E.; Kane, J. L.; Katzy, J.; Khan, N.; Kucewicz, W.; Kulinich, P.; Kuo, C. M.; Lin, W. T.; Manly, S.; McLeod, D.; Michałowski, J.; Mignerey, A. C.; Nouicer, R.; Olszewski, A.; Pak, R.; Park, I. C.; Pernegger, H.; Reed, C.; Remsberg, L. P.; Reuter, M.; Roland, C.; Roland, G.; Rosenberg, L.; Sagerer, J.; Sarin, P.; Sawicki, P.; Skulski, W.; Steadman, S. G.; Steinberg, P.; Stephans, G. S.; Stodulski, M.; Sukhanov, A.; Tang, J.-L.; Teng, R.; Trzupek, A.; Vale, C.; van Nieuwenhuizen, G. J.; Verdier, R.; Wadsworth, B.; Wolfs, F. L.; Wosiek, B.; Woźniak, K.; Wuosmaa, A. H.; Wysłouch, B.

2003-02-01

The ratios of charged antiparticles to particles have been obtained for pions, kaons, and protons near midrapidity in central Au+Au collisions at (sNN)=200 GeV. Ratios of <π->/<π+>=1.025±0.006(stat.)±0.018(syst.), /=0.95±0.03(stat.)±0.03(syst.), and / =0.73±0.02(stat.)±0.03(syst.) have been observed. The / and / ratios are consistent with a baryochemical potential μB of 27 MeV, roughly a factor of 2 smaller than in (sNN)=130 GeV collisions. The data are compared to results from lower energies and model calculations. Our accurate measurements of the particle ratios impose stringent constraints on current and future models dealing with baryon production and transport.

On the CCN (de)activation nonlinearities

NASA Astrophysics Data System (ADS)

Arabas, Sylwester; Shima, Shin-ichiro

2017-09-01

We take into consideration the evolution of particle size in a monodisperse aerosol population during activation and deactivation of cloud condensation nuclei (CCN). Our analysis reveals that the system undergoes a saddle-node bifurcation and a cusp catastrophe. The control parameters chosen for the analysis are the relative humidity and the particle concentration. An analytical estimate of the activation timescale is derived through estimation of the time spent in the saddle-node bifurcation bottleneck. Numerical integration of the system coupled with a simple air-parcel cloud model portrays two types of activation/deactivation hystereses: one associated with the kinetic limitations on droplet growth when the system is far from equilibrium, and one occurring close to equilibrium and associated with the cusp catastrophe. We discuss the presented analyses in context of the development of particle-based models of aerosol-cloud interactions in which activation and deactivation impose stringent time-resolution constraints on numerical integration.

Active matter logic for autonomous microfluidics

NASA Astrophysics Data System (ADS)

Woodhouse, Francis G.; Dunkel, Jörn

2017-04-01

Chemically or optically powered active matter plays an increasingly important role in materials design, but its computational potential has yet to be explored systematically. The competition between energy consumption and dissipation imposes stringent physical constraints on the information transport in active flow networks, facilitating global optimization strategies that are not well understood. Here, we combine insights from recent microbial experiments with concepts from lattice-field theory and non-equilibrium statistical mechanics to introduce a generic theoretical framework for active matter logic. Highlighting conceptual differences with classical and quantum computation, we demonstrate how the inherent non-locality of incompressible active flow networks can be utilized to construct universal logical operations, Fredkin gates and memory storage in set-reset latches through the synchronized self-organization of many individual network components. Our work lays the conceptual foundation for developing autonomous microfluidic transport devices driven by bacterial fluids, active liquid crystals or chemically engineered motile colloids.

25 CFR 900.36 - What requirements are imposed upon Indian tribes or tribal organizations by this subpart?

Code of Federal Regulations, 2012 CFR

2012-04-01

... THE INDIAN SELF-DETERMINATION AND EDUCATION ASSISTANCE ACT Standards for Tribal or Tribal Organization Management Systems General § 900.36 What requirements are imposed upon Indian tribes or tribal organizations... tribal organizations by this subpart? 900.36 Section 900.36 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT...

25 CFR 900.36 - What requirements are imposed upon Indian tribes or tribal organizations by this subpart?

Code of Federal Regulations, 2014 CFR

2014-04-01

... THE INDIAN SELF-DETERMINATION AND EDUCATION ASSISTANCE ACT Standards for Tribal or Tribal Organization Management Systems General § 900.36 What requirements are imposed upon Indian tribes or tribal organizations... tribal organizations by this subpart? 900.36 Section 900.36 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT...

25 CFR 900.36 - What requirements are imposed upon Indian tribes or tribal organizations by this subpart?

Code of Federal Regulations, 2011 CFR

2011-04-01

... THE INDIAN SELF-DETERMINATION AND EDUCATION ASSISTANCE ACT Standards for Tribal or Tribal Organization Management Systems General § 900.36 What requirements are imposed upon Indian tribes or tribal organizations... tribal organizations by this subpart? 900.36 Section 900.36 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT...

25 CFR 900.36 - What requirements are imposed upon Indian tribes or tribal organizations by this subpart?

Code of Federal Regulations, 2010 CFR

2010-04-01

... THE INDIAN SELF-DETERMINATION AND EDUCATION ASSISTANCE ACT Standards for Tribal or Tribal Organization Management Systems General § 900.36 What requirements are imposed upon Indian tribes or tribal organizations... tribal organizations by this subpart? 900.36 Section 900.36 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT...

25 CFR 900.36 - What requirements are imposed upon Indian tribes or tribal organizations by this subpart?

Code of Federal Regulations, 2013 CFR

2013-04-01

... THE INDIAN SELF-DETERMINATION AND EDUCATION ASSISTANCE ACT Standards for Tribal or Tribal Organization Management Systems General § 900.36 What requirements are imposed upon Indian tribes or tribal organizations... tribal organizations by this subpart? 900.36 Section 900.36 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT...

13 CFR 109.440 - Requirements imposed under other laws and orders.

Code of Federal Regulations, 2012 CFR

2012-01-01

... laws and orders. 109.440 Section 109.440 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION... Requirements imposed under other laws and orders. Loans made by the ILP Intermediary under this program must comply with all applicable laws, including §§ 120.170 (Flood insurance), 120.172 (Flood-plain and...

13 CFR 109.440 - Requirements imposed under other laws and orders.

Code of Federal Regulations, 2014 CFR

2014-01-01

... laws and orders. 109.440 Section 109.440 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION... Requirements imposed under other laws and orders. Loans made by the ILP Intermediary under this program must comply with all applicable laws, including §§ 120.170 (Flood insurance), 120.172 (Flood-plain and...

13 CFR 109.440 - Requirements imposed under other laws and orders.

Code of Federal Regulations, 2013 CFR

2013-01-01

... laws and orders. 109.440 Section 109.440 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION... Requirements imposed under other laws and orders. Loans made by the ILP Intermediary under this program must comply with all applicable laws, including §§ 120.170 (Flood insurance), 120.172 (Flood-plain and...

49 CFR 382.111 - Other requirements imposed by employers.

Code of Federal Regulations, 2011 CFR

2011-10-01

... CONTROLLED SUBSTANCES AND ALCOHOL USE AND TESTING General § 382.111 Other requirements imposed by employers. Except as expressly provided in this part, nothing in this part shall be construed to affect the authority of employers, or the rights of drivers, with respect to the use of alcohol, or the use of...

49 CFR 382.111 - Other requirements imposed by employers.

Code of Federal Regulations, 2013 CFR

2013-10-01

... CONTROLLED SUBSTANCES AND ALCOHOL USE AND TESTING General § 382.111 Other requirements imposed by employers. Except as expressly provided in this part, nothing in this part shall be construed to affect the authority of employers, or the rights of drivers, with respect to the use of alcohol, or the use of...

49 CFR 382.111 - Other requirements imposed by employers.

Code of Federal Regulations, 2014 CFR

2014-10-01

... CONTROLLED SUBSTANCES AND ALCOHOL USE AND TESTING General § 382.111 Other requirements imposed by employers. Except as expressly provided in this part, nothing in this part shall be construed to affect the authority of employers, or the rights of drivers, with respect to the use of alcohol, or the use of...

49 CFR 382.111 - Other requirements imposed by employers.

Code of Federal Regulations, 2012 CFR

2012-10-01

... CONTROLLED SUBSTANCES AND ALCOHOL USE AND TESTING General § 382.111 Other requirements imposed by employers. Except as expressly provided in this part, nothing in this part shall be construed to affect the authority of employers, or the rights of drivers, with respect to the use of alcohol, or the use of...

49 CFR 382.111 - Other requirements imposed by employers.

Code of Federal Regulations, 2010 CFR

2010-10-01

... CONTROLLED SUBSTANCES AND ALCOHOL USE AND TESTING General § 382.111 Other requirements imposed by employers. Except as expressly provided in this part, nothing in this part shall be construed to affect the authority of employers, or the rights of drivers, with respect to the use of alcohol, or the use of...

42 CFR 64a.104 - What requirements are imposed upon grantees?

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 1 2012-10-01 2012-10-01 false What requirements are imposed upon grantees? 64a.104 Section 64a.104 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES FELLOWSHIPS, INTERNSHIPS, TRAINING OBLIGATED SERVICE FOR MENTAL HEALTH TRAINEESHIPS § 64a.104 What...

42 CFR 64a.104 - What requirements are imposed upon grantees?

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 1 2011-10-01 2011-10-01 false What requirements are imposed upon grantees? 64a.104 Section 64a.104 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES FELLOWSHIPS, INTERNSHIPS, TRAINING OBLIGATED SERVICE FOR MENTAL HEALTH TRAINEESHIPS § 64a.104 What...

42 CFR 64a.104 - What requirements are imposed upon grantees?

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false What requirements are imposed upon grantees? 64a.104 Section 64a.104 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES FELLOWSHIPS, INTERNSHIPS, TRAINING OBLIGATED SERVICE FOR MENTAL HEALTH TRAINEESHIPS § 64a.104 What...

42 CFR 64a.104 - What requirements are imposed upon grantees?

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 1 2014-10-01 2014-10-01 false What requirements are imposed upon grantees? 64a.104 Section 64a.104 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES FELLOWSHIPS, INTERNSHIPS, TRAINING OBLIGATED SERVICE FOR MENTAL HEALTH TRAINEESHIPS § 64a.104 What...

42 CFR 64a.104 - What requirements are imposed upon grantees?

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 1 2013-10-01 2013-10-01 false What requirements are imposed upon grantees? 64a.104 Section 64a.104 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES FELLOWSHIPS, INTERNSHIPS, TRAINING OBLIGATED SERVICE FOR MENTAL HEALTH TRAINEESHIPS § 64a.104 What...

The Further Development of Heat-Resistant Materials for Aircraft Engines

NASA Technical Reports Server (NTRS)

Bollenrath, Franz

1946-01-01

The present report deals with the problems involved in the greater utilization and development of aircraft engine materials, and specifically; piston materials, cylinder heads, exhaust valves, and exhaust gas turbine blading. The blades of the exhaust gas turbine are likely to be the highest stressed components of modern power plants from a thermal-mechanical and chemical standpoint, even though the requirements on exhaust valves of engines with gasoline injection are in general no less stringent. For the fire plate in Diesel engines the specifications for mechanical strength and design are not so stringent, and the question of heat resistance, which under these circumstances is easier obtainable, predominates.

76 FR 57515 - Energy Conservation Program: Energy Conservation Standards for Residential Refrigerators...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-15

...The Energy Policy and Conservation Act (EPCA) prescribes energy conservation standards for various consumer products and commercial and industrial equipment, including refrigerators, refrigerator-freezers, and freezers. EPCA also requires the U.S. Department of Energy (DOE) to determine if more stringent, amended standards for these products are technologically feasible and economically justified, and would save a significant amount of energy. In this final rule, DOE is adopting more stringent energy conservation standards for refrigerators, refrigerator-freezers, and freezers. It has determined that the amended energy conservation standards for these products would result in the significant conservation of energy and are technologically feasible and economically justified.

Welding and joining techniques.

PubMed

Chipperfield, F A; Dunkerton, S B

2001-05-01

There is a welding solution for most applications. As products must meet more stringent requirements or require more flexible processes to aid design or reduce cost, further improvements or totally new processes are likely to be developed. Quality control aspects are also becoming more important to meet regulation, and monitoring and control of welding processes and the standardised testing of joints will meet some if not all of these requirements.

Predictors of juveniles' noncompliance with probation requirements.

PubMed

NeMoyer, Amanda; Goldstein, Naomi E S; McKitten, Rhonda L; Prelic, Ana; Ebbecke, Jenna; Foster, Erika; Burkard, Casey

2014-12-01

Probation is the most common disposition for adjudicated youth, but little is known about which specific requirements are commonly imposed on juveniles, the requirements with which juveniles most often fail to comply, and how certain youth characteristics and/or imposed requirements might relate to probation noncompliance. An investigation of 120 archived files of youth represented by an urban public defender's office identified 29 probation requirements imposed on youth and 18 requirements with which youth commonly failed to comply. Results revealed that 52% of youth failed to comply with at least one probation requirement; prior probation noncompliance and race were both significantly associated with noncompliance in the examined probation disposition. In addition, the probability of probation noncompliance was significantly higher when youth received either of two substance-related probation requirements: drug tests or drug and alcohol counseling. Such results may prompt further investigation of juvenile probation-related predictors, identify areas of need for clinical service provision to foster successful completion of probation requirements, and help identify areas of potential biases among juvenile court personnel. PsycINFO Database Record (c) 2014 APA, all rights reserved.

Benefits of advanced software techniques for mission planning systems

NASA Technical Reports Server (NTRS)

Gasquet, A.; Parrod, Y.; Desaintvincent, A.

1994-01-01

The increasing complexity of modern spacecraft, and the stringent requirement for maximizing their mission return, call for a new generation of Mission Planning Systems (MPS). In this paper, we discuss the requirements for the Space Mission Planning and the benefits which can be expected from Artificial Intelligence techniques through examples of applications developed by Matra Marconi Space.

Benefits of advanced software techniques for mission planning systems

NASA Astrophysics Data System (ADS)

Gasquet, A.; Parrod, Y.; Desaintvincent, A.

1994-10-01

The increasing complexity of modern spacecraft, and the stringent requirement for maximizing their mission return, call for a new generation of Mission Planning Systems (MPS). In this paper, we discuss the requirements for the Space Mission Planning and the benefits which can be expected from Artificial Intelligence techniques through examples of applications developed by Matra Marconi Space.

School Meal Programs: Revenue and Expense Information from Selected States. Report to Congressional Requesters.

ERIC Educational Resources Information Center

Bellis, David D.

In school year 1996-97, the Department of Agriculture instituted more stringent requirements for the nutritional content of school meals. The General Accounting Office was asked to study school food-service revenues and expenses and how they had changed since the requirements went into effect. This report contains information of the sources of…

26 CFR 1.148-8 - Small issuer exception to rebate requirement.

Code of Federal Regulations, 2010 CFR

2010-04-01

...) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Tax Exemption Requirements for State and Local Bonds § 1... taxing powers if it has the power to impose taxes (or to cause another entity to impose taxes) of general... limited to a specific type of tax, provided that the applicability of the tax is not limited to a small...

Radiometry of liquids: characteristics and systematization of the requirements imposed on it (in Russian)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Isakov, L.M.; El'tsin, G.I.

1972-01-01

The requirements imposed on the measurement of the radioactivity of liquids are differentiated as a function of the purpose of the instrument. Five groups of radiometers were examined and for each the individual requirements were characterized. The proposed systematization was oriented toward the ordering of the development of liquid radiometers and a reduction in the number of models without limiting their range of applicability. (tr-auth)

Contaminant levels, source strengths, and ventilation rates in California retail stores.

PubMed

Chan, W R; Cohn, S; Sidheswaran, M; Sullivan, D P; Fisk, W J

2015-08-01

This field study measured ventilation rates and indoor air quality in 21 visits to retail stores in California. Three types of stores, such as grocery, furniture/hardware stores, and apparel, were sampled. Ventilation rates measured using a tracer gas decay method exceeded the minimum requirement of California's Title 24 Standard in all but one store. Concentrations of volatile organic compounds (VOCs), ozone, and carbon dioxide measured indoors and outdoors were analyzed. Even though there was adequate ventilation according to standard, concentrations of formaldehyde and acetaldehyde exceeded the most stringent chronic health guidelines in many of the sampled stores. The whole-building emission rates of VOCs were estimated from the measured ventilation rates and the concentrations measured indoor and outdoor. Estimated formaldehyde emission rates suggest that retail stores would need to ventilate at levels far exceeding the current Title 24 requirement to lower indoor concentrations below California's stringent formaldehyde reference level. Given the high costs of providing ventilation, effective source control is an attractive alternative. Field measurements suggest that California retail stores were well ventilated relative to the minimum ventilation rate requirement specified in the Building Energy Efficiency Standards Title 24. Concentrations of formaldehyde found in retail stores were low relative to levels found in homes but exceeded the most stringent chronic health guideline. Looking ahead, California is mandating zero energy commercial buildings by 2030. To reduce the energy use from building ventilation while maintaining or even lowering formaldehyde in retail stores, effective formaldehyde source control measures are vitally important. Published 2014. This article is a U.S. Government work and is in the public domain in the USA.

[Mechanical Shimming Method and Implementation for Permanent Magnet of MRI System].

PubMed

Xue, Tingqiang; Chen, Jinjun

2015-03-01

A mechanical shimming method and device for permanent magnet of MRI system has been developed to meet its stringent homogeneity requirement without time-consuming passive shimming on site, installation and adjustment efficiency has been increased.

A Viking satellite orbit trim strategy

NASA Technical Reports Server (NTRS)

Hintz, G. R.

1971-01-01

One strategy is submitted for meeting the varied and stringent requirements of the Viking Project on the control of the satellite orbit to obtain reconnaissance and to prepare for lander release. To satisfy these requirements, different orbit trim maneuver strategies were developed for two typical Viking missions. In addition, a summary of recent numerical results is included to show that this strategy satisfies the mission requirements which have been identified.

45 CFR 264.72 - What requirements are imposed on a State if it receives contingency funds?

Code of Federal Regulations, 2010 CFR

2010-10-01

... receives contingency funds? 264.72 Section 264.72 Public Welfare Regulations Relating to Public Welfare... Contingency Fund? § 264.72 What requirements are imposed on a State if it receives contingency funds? (a)(1) A State must meet a Contingency Fund MOE level of 100 percent of historic State expenditures for FY 1994...

Polarization modeling and predictions for DKIST part 3: focal ratio and thermal dependencies of spectral polarization fringes and optic retardance

NASA Astrophysics Data System (ADS)

Harrington, David M.; Sueoka, Stacey R.

2018-01-01

Data products from high spectral resolution astronomical polarimeters are often limited by fringes. Fringes can skew derived magnetic field properties from spectropolarimetric data. Fringe removal algorithms can also corrupt the data if the fringes and object signals are too similar. For some narrow-band imaging polarimeters, fringes change the calibration retarder properties and dominate the calibration errors. Systems-level engineering tools for polarimetric instrumentation require accurate predictions of fringe amplitudes, periods for transmission, diattenuation, and retardance. The relevant instabilities caused by environmental, thermal, and optical properties can be modeled and mitigation tools developed. We create spectral polarization fringe amplitude and temporal instability predictions by applying the Berreman calculus and simple interferometric calculations to optics in beams of varying F/ number. We then apply the formalism to superachromatic six-crystal retarders in converging beams under beam thermal loading in outdoor environmental conditions for two of the world's largest observatories: the 10-m Keck telescope and the Daniel K. Inouye Solar Telescope (DKIST). DKIST will produce a 300-W optical beam, which has imposed stringent requirements on the large diameter six-crystal retarders, dichroic beamsplitters, and internal optics. DKIST retarders are used in a converging beam with F/ ratios between 8 and 62. The fringe spectral periods, amplitudes, and thermal models of retarder behavior assisted DKIST optical designs and calibration plans with future application to many astronomical spectropolarimeters. The Low Resolution Imaging Spectrograph with polarimetry instrument at Keck also uses six-crystal retarders in a converging F / 13 beam in a Cassegrain focus exposed to summit environmental conditions providing observational verification of our predictions.

Laser intensity scaling through stimulated scattering in optical fibers

NASA Astrophysics Data System (ADS)

Russell, Timothy H.

The influence of stimulated scattering on laser intensity in fiber optic waveguides is examined. Stimulated Brillouin scattering (SBS) in long, multimode optical waveguides is found to generate a Stokes beam that propagates in the fiber LP01 mode. This characteristic of the Stokes beam was first applied to beam cleanup, where an aberrated pump generated a Gaussian-like Stokes beam. Additionally, the same process is found to combine multiple laser beams into a single spatially coherent source. The mean square difference between the two beams was used to measure the degree of spatial overlap, demonstrating spatial coherence between the Stokes beams even when the pump beams are not spatially correlated. This result is obtained regardless of whether the pump beams are at the same or different frequencies; producing two temporally coherent or incoherent Stokes beams respectively. Limitations in beam cleanup and combining are also examined to identify ways to overcome them. Output couplers are designed that could be used to spatially filter the Stokes beam from the pump, thus increasing the number of beams that could be combined. The combined power restriction induced by second order Stokes threshold is examined experimentally and theoretically and is not found to be a significant limitation. Finally, stimulated Raman scattering (SRS) beam cleanup is examined to overcome the stringent spectral requirements on the pump beams required by SBS. The last portion of the dissertation theoretically examines suppression of stimulated Raman scattering in fibers to eliminate the restriction this imposes on the power of a fiber laser or amplifier. The suppression was modeled using both a holmium dopant and adding a long period grating to the fiber. Both methods were shown to have a significant effect on the SRS threshold.

NASA's Aeroacoustic Tools and Methods for Analysis of Aircraft Noise

NASA Technical Reports Server (NTRS)

Rizzi, Stephen A.; Lopes, Leonard V.; Burley, Casey L.

2015-01-01

Aircraft community noise is a significant concern due to continued growth in air traffic, increasingly stringent environmental goals, and operational limitations imposed by airport authorities. The ability to quantify aircraft noise at the source and ultimately at observers is required to develop low noise aircraft designs and flight procedures. Predicting noise at the source, accounting for scattering and propagation through the atmosphere to the observer, and assessing the perception and impact on a community requires physics-based aeroacoustics tools. Along with the analyses for aero-performance, weights and fuel burn, these tools can provide the acoustic component for aircraft MDAO (Multidisciplinary Design Analysis and Optimization). Over the last decade significant progress has been made in advancing the aeroacoustic tools such that acoustic analyses can now be performed during the design process. One major and enabling advance has been the development of the system noise framework known as Aircraft NOise Prediction Program2 (ANOPP2). ANOPP2 is NASA's aeroacoustic toolset and is designed to facilitate the combination of acoustic approaches of varying fidelity for the analysis of noise from conventional and unconventional aircraft. The toolset includes a framework that integrates noise prediction and propagation methods into a unified system for use within general aircraft analysis software. This includes acoustic analyses, signal processing and interfaces that allow for the assessment of perception of noise on a community. ANOPP2's capability to incorporate medium fidelity shielding predictions and wind tunnel experiments into a design environment is presented. An assessment of noise from a conventional and Hybrid Wing Body (HWB) aircraft using medium fidelity scattering methods combined with noise measurements from a model-scale HWB recently placed in NASA's 14x22 wind tunnel are presented. The results are in the form of community noise metrics and auralizations.

Prototyping and implementing flight qualifiable semicustom CMOS P-well bulk integrated circuits in the JPL environment

NASA Technical Reports Server (NTRS)

Olson, E. M.

1986-01-01

Presently, there are many difficulties associated with implementing application specific custom or semi-custom (standard cell based) integrated circuits (ICs) into JPL flight projects. One of the primary difficulties is developing prototype semi-custom integrated circuits for use and evaluation in engineering prototype flight hardware. The prototype semi-custom ICs must be extremely cost-effective and yet still representative of flight qualifiable versions of the design. A second difficulty is encountered in the transport of the design from engineering prototype quality to flight quality. Normally, flight quality integrated circuits have stringent quality standards, must be radiation resistant and should consume minimal power. It is often not necessary or cost effective, however, to impose such stringent quality standards on engineering models developed for systems analysis in controlled lab environments. This article presents work originally initiated for ground based applications that also addresses these two problems. Furthermore, this article suggests a method that has been shown successful in prototyping flight quality semi-custom ICs through the Metal Oxide Semiconductor Implementation Service (MOSIS) program run by the University of Southern California's Information Sciences Institute. The method has been used successfully to design and fabricate through the MOSIS three different semi-custom prototype CMOS p-well chips. The three designs make use of the work presented and were designed consistent with design techniques and structures that are flight qualifiable, allowing one hour transfer of the design from engineering model status to flight qualifiable foundry-ready status through methods outlined in this article.

Fertility and Parental Consent for Minors to Receive Contraceptives

PubMed Central

Zavodny, Madeline

2004-01-01

Objectives. I examined the effect of imposing a requirement for parental consent before minors can receive medical contraceptives. Methods. Birth and abortions among teens, relative to adults, in a suburban Illinois county that imposed a parental consent requirement in 1998 were compared with births and abortions in nearby counties during the period 1997–2000. Results. The relative proportion of births to women under age 19 years in the county rose significantly compared with nearby counties, whereas the relative proportion of abortions to women under age 20 years declined insignificantly, with a relative increase in the proportion of pregnancies (births and abortions) to young women in the county. Conclusions. Imposing a parental consent requirement for contraceptives, but not abortions, appears to raise the frequency of pregnancies and births among young women. PMID:15284042

40 CFR 131.4 - State authority.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS WATER QUALITY STANDARDS... reviewing, establishing, and revising water quality standards. As recognized by section 510 of the Clean Water Act, States may develop water quality standards more stringent than required by this regulation...

40 CFR 63.11118 - Requirements for facilities with monthly throughput of 100,000 gallons of gasoline or more.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Management Practices § 63.11118 Requirements for facilities with monthly throughput of 100,000 gallons of...)(1) or paragraph (b)(2) of this section. (1) Each management practice in Table 1 to this subpart that...) Operates using management practices at least as stringent as those in Table 1 to this subpart. (ii) Your...

Environmental Quality: Environmental Protection and Enhancement

DTIC Science & Technology

2002-01-17

have an adverse effect on human health . These regulations are federally enforceable. Primacy states may have more stringent requirements. Primary...includes TT requirements for filtered and unfiltered systems that are specifically designed to protect against the adverse health effects of exposure to...MTBE (20) Alachlor ESA (36) Lead- 210 (9) Nitrobenzene (21) 1,2-diphenylhydrazine (37) Polonium - 210 (10) Terbacil (22) Diazinon (11) Acetochlor (23

Investigation of material improvements to mitigate the abrasive wear mechanism of concrete crosstie rail seat deterioration (RSD).

DOT National Transportation Integrated Search

2014-11-01

To meet the increasingly stringent design and performance requirements due to increasing cumulative : gross tonnages from heavy-haul freight operations, along with increased high-speed inter-city passenger : rail development, improvements in concrete...

Deriving protection thresholds for threatened and endangered species potentially exposed to pesticides

EPA Science Inventory

The Endangered Species Act requires specific and stringent protection to threatened and endangered species and their critical habitat. Therefore, protective methods for risk assessment for such species are needed. Species sensitivity distributions (SSDs) are a common tool used fo...

76 FR 20556 - Changes in Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-13

... stringent in their floodplain management requirements. The community may at any time enact stricter... DEPARTMENT OF HOMELAND SECURITY Federal Emergency Management Agency 44 CFR Part 65 [Docket ID FEMA...: Federal Emergency Management Agency, DHS. ACTION: Interim rule. SUMMARY: This interim rule lists...

76 FR 43601 - Changes in Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-21

... stringent in their floodplain management requirements. The community may at any time enact stricter... DEPARTMENT OF HOMELAND SECURITY Federal Emergency Management Agency 44 CFR Part 65 [Docket ID FEMA...: Federal Emergency Management Agency, DHS. ACTION: Interim rule. SUMMARY: This interim rule lists...

Dual Regulation of Bacillus subtilis kinB Gene Encoding a Sporulation Trigger by SinR through Transcription Repression and Positive Stringent Transcription Control.

PubMed

Fujita, Yasutaro; Ogura, Mitsuo; Nii, Satomi; Hirooka, Kazutake

2017-01-01

It is known that transcription of kinB encoding a trigger for Bacillus subtilis sporulation is under repression by SinR, a master repressor of biofilm formation, and under positive stringent transcription control depending on the adenine species at the transcription initiation nucleotide (nt). Deletion and base substitution analyses of the kinB promoter (P kinB ) region using lacZ fusions indicated that either a 5-nt deletion (Δ5, nt -61/-57, +1 is the transcription initiation nt) or the substitution of G at nt -45 with A (G-45A) relieved kinB repression. Thus, we found a pair of SinR-binding consensus sequences (GTTCTYT; Y is T or C) in an inverted orientation (SinR-1) between nt -57/-42, which is most likely a SinR-binding site for kinB repression. This relief from SinR repression likely requires SinI, an antagonist of SinR. Surprisingly, we found that SinR is essential for positive stringent transcription control of P kinB . Electrophoretic mobility shift assay (EMSA) analysis indicated that SinR bound not only to SinR-1 but also to SinR-2 (nt -29/-8) consisting of another pair of SinR consensus sequences in a tandem repeat arrangement; the two sequences partially overlap the '-35' and '-10' regions of P kinB . Introduction of base substitutions (T-27C C-26T) in the upstream consensus sequence of SinR-2 affected positive stringent transcription control of P kinB , suggesting that SinR binding to SinR-2 likely causes this positive control. EMSA also implied that RNA polymerase and SinR are possibly bound together to SinR-2 to form a transcription initiation complex for kinB transcription. Thus, it was suggested in this work that derepression of kinB from SinR repression by SinI induced by Spo0A∼P and occurrence of SinR-dependent positive stringent transcription control of kinB might induce effective sporulation cooperatively, implying an intimate interplay by stringent response, sporulation, and biofilm formation.

Synthesis and Transfer of Large-Area Monolayer WS2 Crystals: Moving Toward the Recyclable Use of Sapphire Substrates.

PubMed

Xu, Zai-Quan; Zhang, Yupeng; Lin, Shenghuang; Zheng, Changxi; Zhong, Yu Lin; Xia, Xue; Li, Zhipeng; Sophia, Ponraj Joice; Fuhrer, Michael S; Cheng, Yi-Bing; Bao, Qiaoliang

2015-06-23

Two-dimensional layered transition metal dichalcogenides (TMDs) show intriguing potential for optoelectronic devices due to their exotic electronic and optical properties. Only a few efforts have been dedicated to large-area growth of TMDs. Practical applications will require improving the efficiency and reducing the cost of production, through (1) new growth methods to produce large size TMD monolayer with less-stringent conditions, and (2) nondestructive transfer techniques that enable multiple reuse of growth substrate. In this work, we report to employ atmospheric pressure chemical vapor deposition (APCVD) for the synthesis of large size (>100 μm) single crystals of atomically thin tungsten disulfide (WS2), a member of TMD family, on sapphire substrate. More importantly, we demonstrate a polystyrene (PS) mediated delamination process via capillary force in water which reduces the etching time in base solution and imposes only minor damage to the sapphire substrate. The transferred WS2 flakes are of excellent continuity and exhibit comparable electron mobility after several growth cycles on the reused sapphire substrate. Interestingly, the photoluminescence emission from WS2 grown on the recycled sapphire is much higher than that on fresh sapphire, possibly due to p-type doping of monolayer WS2 flakes by a thin layer of water intercalated at the atomic steps of the recycled sapphire substrate. The growth and transfer techniques described here are expected to be applicable to other atomically thin TMD materials.

Pseudolinear gradient ultrahigh-pressure liquid chromatography using an injection valve assembly.

PubMed

Xiang, Yanqiao; Liu, Yansheng; Stearns, Stanley D; Plistil, Alex; Brisbin, Martin P; Lee, Milton L

2006-02-01

The use of ultrahigh pressures in liquid chromatography (UHPLC) imposes stringent requirements on hardware such as pumps, valves, injectors, connecting tubing, and columns. One of the most difficult components of the UHPLC system to develop has been the sample injector. Static-split injection, which can be performed at pressures up to 6900 bar (100,000 psi), consumes a large sample volume and is very irreproducible. A pressure-balanced injection valve provided better reproducibility, shorter injection time, reduced sample consumption, and greater ease of use; however, it could only withstand pressures up to approximately 1000 bar (15,000 psi). In this study, a new injection valve assembly that can operate at pressures as high as 2070 bar (30,000 psi) was evaluated for UHPLC. This assembly contains six miniature electronically controlled needle valves to provide accurate and precise volumes for introduction into the capillary LC column. It was found that sample volumes as small as several tenths of a nanoliter can be injected, which are comparable to the results obtained from the static-split injector. The reproducibilities of retention time, efficiency, and peak area were investigated, and the results showed that the relative standard deviations of these parameters were small enough for quantitative analyses. Separation experiments using the UHPLC system with this new injection valve assembly showed that this new injector is suitable for both isocratic and gradient operation modes. A newly designed capillary connector was used at a pressure as high as 2070 bar (30,000 psi).

Detecting Chemical Weapons: Threats, Requirements, Solutions, and Future Challenges

NASA Astrophysics Data System (ADS)

Boso, Brian

2011-03-01

Although chemicals have been reportedly used as weapons for thousands of years, it was not until 1915 at Ypres, France that an industrial chemical, chlorine, was used in World War I as an offensive weapon in significant quantity, causing mass casualties. From that point until today the development, detection, production and protection from chemical weapons has be an organized endeavor of many of the world's armed forces and in more recent times, non-governmental terrorist organizations. The number of Chemical Warfare Agents (CWAs) has steadily increased as research into more toxic substances continued for most of the 20 th century. Today there are over 70 substances including harassing agents like tear gas, incapacitating agents, and lethal agents like blister, blood, chocking, and nerve agents. The requirements for detecting chemical weapons vary depending on the context in which they are encountered and the concept of operation of the organization deploying the detection equipment. The US DoD, for example, has as a requirement, that US forces be able to continue their mission, even in the event of a chemical attack. This places stringent requirements on detection equipment. It must be lightweight (<2 lbs), detect a large array of chemical warfare agents and toxic industrial chemicals, detect and warn at concentration levels and time duration to prevent acute health effects, meet military ruggedness specifications and work over a wide range of temperature and humidity, and have a very high probability of detection with a similarly low probability of false positives. The current technology of choice to meet these stringent requirements is Ion Mobility Spectrometry. Many technologies are capable of detecting chemicals at the trace levels required and have been extensively developed for this application, including, but not limited to: mass spectroscopy, IR spectroscopy, RAMAN spectroscopy, MEMs micro-cantilever sensors, surface acoustic wave sensors, differential mobility spectrometry, and amplifying fluorescence polymers. In the future the requirements for detection equipment will continue to become even more stringent. The continuing increase in the sheer number of threats that will need to be detected, the development of binary agents requiring that even the precursor chemicals be detected, the development of new types of agents unlike any of the current chemistries, and the expansion of the list of toxic industrial chemical will require new techniques with higher specificity and more sensitivity.

Space Geodetic Technique Co-location in Space: Simulation Results for the GRASP Mission

NASA Astrophysics Data System (ADS)

Kuzmicz-Cieslak, M.; Pavlis, E. C.

2011-12-01

The Global Geodetic Observing System-GGOS, places very stringent requirements in the accuracy and stability of future realizations of the International Terrestrial Reference Frame (ITRF): an origin definition at 1 mm or better at epoch and a temporal stability on the order of 0.1 mm/y, with similar numbers for the scale (0.1 ppb) and orientation components. These goals were derived from the requirements of Earth science problems that are currently the international community's highest priority. None of the geodetic positioning techniques can achieve this goal alone. This is due in part to the non-observability of certain attributes from a single technique. Another limitation is imposed from the extent and uniformity of the tracking network and the schedule of observational availability and number of suitable targets. The final limitation derives from the difficulty to "tie" the reference points of each technique at the same site, to an accuracy that will support the GGOS goals. The future GGOS network will address decisively the ground segment and to certain extent the space segment requirements. The JPL-proposed multi-technique mission GRASP (Geodetic Reference Antenna in Space) attempts to resolve the accurate tie between techniques, using their co-location in space, onboard a well-designed spacecraft equipped with GNSS receivers, a SLR retroreflector array, a VLBI beacon and a DORIS system. Using the anticipated system performance for all four techniques at the time the GGOS network is completed (ca 2020), we generated a number of simulated data sets for the development of a TRF. Our simulation studies examine the degree to which GRASP can improve the inter-technique "tie" issue compared to the classical approach, and the likely modus operandi for such a mission. The success of the examined scenarios is judged by the quality of the origin and scale definition of the resulting TRF.

Manufacturing considerations for AMLCD cockpit displays

NASA Astrophysics Data System (ADS)

Luo, Fang-Chen

1995-06-01

AMLCD cockpit displays need to meet more stringent requirements compared with AMLCD commercial displays in areas such as environmental conditions, optical performance and device reliability. Special considerations are required for the manufacturing of AMLCD cockpit displays in each process step to address these issues. Some examples are: UV stable polarizers, wide-temperature LC material, strong LC glue seal, ESS test system, gray scale voltage EEPROM, etc.

Wire-Arc-Sprayed Aluminum Protects Steel Against Corrosion

NASA Technical Reports Server (NTRS)

Zimmerman, Frank R.; Poorman, Richard; Sanders, Heather L.; Mckechnie, Timothy N.; Bonds, James W., Jr.; Daniel, Ronald L., Jr.

1995-01-01

Aluminum coatings wire-arc sprayed onto steel substrates found effective in protecting substrates against corrosion. Coatings also satisfy stringent requirements for adhesion and flexibility, both at room temperature and at temperatures as low as liquid hydrogen. Developed as alternatives to corrosion-inhibiting primers and paints required by law to be phased out because they contain and emit such toxic substances as chromium and volatile organic compounds.

Guanosine 3'-diphosphate 5'-diphosphate is not required for growth rate-dependent control of rRNA synthesis in Escherichia coli.

PubMed Central

Gaal, T; Gourse, R L

1990-01-01

rRNA synthesis in Escherichia coli is subject to at least two regulation systems, growth rate-dependent control and stringent control. The inverse correlation between rRNA synthesis rates and guanosine 3'-diphosphate 5'-diphosphate (ppGpp) levels under various physiological conditions has led to the supposition that ppGpp is the mediator of both control mechanisms by inhibiting transcription from rrn P1 promoters. Recently, relA- spoT- strains have been constructed in which both ppGpp synthesis pathways most likely have been removed (M. Cashel, personal communication). We have confirmed that such strains produce no detectable ppGpp and therefore offer a direct means for testing the involvement of ppGpp in the regulation of rRNA synthesis in vivo. Stringent control was determined by measurement of rRNA synthesis after amino acid starvation, while growth rate control was determined by measurement of rRNA synthesis under different nutritional conditions. As expected, the relA- spoT- strain is relaxed for stringent control. However, growth rate-dependent regulation is unimpaired. These results indicate that growth rate regulation can occur in the absence of ppGpp and imply that ppGpp is not the mediator, or at least is not the sole mediator, of growth rate-dependent control. Therefore, growth rate-dependent control and stringent control may utilize different mechanisms for regulating stable RNA synthesis. PMID:2196571

Whole-Genome Microarray and Gene Deletion Studies Reveal Regulation of the Polyhydroxyalkanoate Production Cycle by the Stringent Response in Ralstonia eutropha H16

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brigham, CJ; Speth, DR; Rha, C

Poly(3-hydroxybutyrate) (PHB) production and mobilization in Ralstonia eutropha are well studied, but in only a few instances has PHB production been explored in relation to other cellular processes. We examined the global gene expression of wild-type R. eutropha throughout the PHB cycle: growth on fructose, PHB production using fructose following ammonium depletion, and PHB utilization in the absence of exogenous carbon after ammonium was resupplied. Our results confirm or lend support to previously reported results regarding the expression of PHB-related genes and enzymes. Additionally, genes for many different cellular processes, such as DNA replication, cell division, and translation, are selectivelymore » repressed during PHB production. In contrast, the expression levels of genes under the control of the alternative sigma factor sigma(54) increase sharply during PHB production and are repressed again during PHB utilization. Global gene regulation during PHB production is strongly reminiscent of the gene expression pattern observed during the stringent response in other species. Furthermore, a ppGpp synthase deletion mutant did not show an accumulation of PHB, and the chemical induction of the stringent response with DL-norvaline caused an increased accumulation of PHB in the presence of ammonium. These results indicate that the stringent response is required for PHB accumulation in R. eutropha, helping to elucidate a thus-far-unknown physiological basis for this process.« less

Regional ITS architecture guidance : developing, using, and maintaining an ITS architecture for your region

DOT National Transportation Integrated Search

1998-08-01

The purpose of this TechBrief is to discuss one of the Long Term Pavement Performance (LTPP) program's stringent data requirements - site-specific measurements for estimating pavement loadings - and to illustrate the effects of traffic loading data e...

40 CFR 142.10 - Requirements for a determination of primary enforcement responsibility.

Code of Federal Regulations, 2010 CFR

2010-07-01

... PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS... enforcement responsibility. A State has primary enforcement responsibility for public water systems in the...: (a) Has adopted drinking water regulations which are no less stringent than the national primary...

EFFECTS OF CHANGING DISINFECTANTS ON LEAD AND COPPER RELEASE– A REVIEW

EPA Science Inventory

More utilities are using chloramines in place of free chlorine for greater residual stability and better compliance with both the Total Coliform Rule (TCR) and more stringent requirements of the Disinfectants/Disinfection By-Products Rule (D/DBPR). However, new information about ...

20 CFR 658.701 - Statements of policy.

Code of Federal Regulations, 2010 CFR

2010-04-01

... ensure that State agencies comply with all requirements established by JS regulations. (b) It is the... continual violations of JS regulations if less stringent remedial actions taken in accordance with this... alleged violations by State agencies of the JS regulations received from any person or organization. ...

40 CFR 281.37 - Financial responsibility for UST systems containing petroleum.

Code of Federal Regulations, 2011 CFR

2011-07-01

... systems containing petroleum. 281.37 Section 281.37 Protection of Environment ENVIRONMENTAL PROTECTION... for No-Less-Stringent § 281.37 Financial responsibility for UST systems containing petroleum. (a) In... UST systems containing petroleum, the state requirements for financial responsibility for petroleum...

40 CFR 142.10 - Requirements for a determination of primary enforcement responsibility.

Code of Federal Regulations, 2013 CFR

2013-07-01

... PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS... enforcement responsibility. A State has primary enforcement responsibility for public water systems in the...: (a) Has adopted drinking water regulations which are no less stringent than the national primary...

40 CFR 142.10 - Requirements for a determination of primary enforcement responsibility.

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS... enforcement responsibility. A State has primary enforcement responsibility for public water systems in the...: (a) Has adopted drinking water regulations which are no less stringent than the national primary...

Contamination control program for the Cosmic Background Explorer

NASA Technical Reports Server (NTRS)

Barney, Richard D.

1991-01-01

Each of the three state of the art instruments flown aboard NASA's Cosmic Background Explorer (COBE) were designed, fabricated, and integrated using unique contamination control procedures to ensure accurate characterization of the diffuse radiation in the universe. The most stringent surface level cleanliness specifications ever attempted by NASA were required by the Diffuse Infrared Background Experiment (DRIBE) which is located inside a liquid helium cooled dewar along with the Far Infrared Absolute Spectrophotometer (FIRAS). The DRIBE instrument required complex stray radiation suppression that defined a cold primary optical baffle system surface cleanliness level of 100A. The cleanliness levels of the cryogenic FIRAS instrument and the Differential Microwave Radiometer (DMR) which were positioned symmetrically around the dewar were less stringent ranging from 300 to 500A. To achieve these instrument cleanliness levels, the entire flight spacecraft was maintained at level 500A throughout each phase of development. The COBE contamination control program is described along with the difficulties experienced in maintaining the cleanliness quality of personnel and flight hardware throughout instrument assembly.

Avoiding Title V permitting pitfalls

DOE Office of Scientific and Technical Information (OSTI.GOV)

Laswell, D.L.

1993-04-01

Title V of the 1990 Clean Air Act Amendments requires states to implement new air operating permit programs. States have a great deal of flexibility in developing their permit programs. Industry should work now to ensure that state programs contain the favorable aspects of the federal regulations and do not contain more stringent requirements that are not required under the Clean Air Act. This article outlines areas of the permit program that have the potential to handicap industry`s ability to expand.

Hubble Space Telescope servicing mission scientific instrument protective enclosure design requirements and contamination controls

NASA Technical Reports Server (NTRS)

Hansen, Patricia A.; Hughes, David W.; Hedgeland, Randy J.; Chivatero, Craig J.; Studer, Robert J.; Kostos, Peter J.

1994-01-01

The Scientific Instrument Protective Enclosures were designed for the Hubble Space Telescope Servicing Missions to provide a beginning environment to a Scientific Instrument during ground and on orbit activities. The Scientific Instruments required very stringent surface cleanliness and molecular outgassing levels to maintain ultraviolet performance. Data from the First Servicing Mission verified that both the Scientific Instruments and Scientific Instrument Protective Enclosures met surface cleanliness level requirements during ground and on-orbit activities.

Earth resources ground data handling systems for the 1980's

NASA Technical Reports Server (NTRS)

Vanvleck, E. M.; Sinclair, K. F.; Pitts, S. W.; Slye, R. E.

1973-01-01

The system requirements of an operational data handling system for earth resources in the decade of the 1980's are investigated. Attention is drawn to problems encountered in meeting the stringent agricultural user requirements of that time frame. Such an understanding of requirements is essential not only in designing the ground system that will ultimately handle the data, but also in design studies of the earth resources platform, sensors, and data relay satellites which may be needed.

Eco-driving: behavioural pattern change in Polish passenger vehicle drivers

NASA Astrophysics Data System (ADS)

Czechowski, Piotr Oskar; Oniszczuk-Jastrząbek, Aneta; Czuba, Tomasz

2018-01-01

In Poland, as in the rest of Europe, air quality depends primarily on emissions from municipal, domestic and road transport sources. The problems of appropriate air quality are especially important within urban areas due to numerous sources of emissions being concentrated in relatively small spaces in both large cities and small/medium-sized towns. Due to the steadily increasing share of urban population in the overall number of population, the issue of providing clean air will over the years become a more significant problem for human health, and therefore a stronger incentive to intensify research. The key challenge faced by a modern society is, therefore, to limit harmful substance emissions in order to minimise the contribution of transport to pollution and health hazards. Increasingly stringent emission standards are being imposed on car manufacturers; on the other hand, scant regard is paid to the issue of drivers, i.e. how they can help reduce emissions and protect their life and health by applying eco-driving rules.

Model-order reduction of lumped parameter systems via fractional calculus

NASA Astrophysics Data System (ADS)

Hollkamp, John P.; Sen, Mihir; Semperlotti, Fabio

2018-04-01

This study investigates the use of fractional order differential models to simulate the dynamic response of non-homogeneous discrete systems and to achieve efficient and accurate model order reduction. The traditional integer order approach to the simulation of non-homogeneous systems dictates the use of numerical solutions and often imposes stringent compromises between accuracy and computational performance. Fractional calculus provides an alternative approach where complex dynamical systems can be modeled with compact fractional equations that not only can still guarantee analytical solutions, but can also enable high levels of order reduction without compromising on accuracy. Different approaches are explored in order to transform the integer order model into a reduced order fractional model able to match the dynamic response of the initial system. Analytical and numerical results show that, under certain conditions, an exact match is possible and the resulting fractional differential models have both a complex and frequency-dependent order of the differential operator. The implications of this type of approach for both model order reduction and model synthesis are discussed.

Compensation of the impact of low-cost manufacturing techniques in the design of E-plane multiport waveguide junctions

NASA Astrophysics Data System (ADS)

San-Blas, A. A.; Roca, J. M.; Cogollos, S.; Morro, J. V.; Boria, V. E.; Gimeno, B.

2016-06-01

In this work, a full-wave tool for the accurate analysis and design of compensated E-plane multiport junctions is proposed. The implemented tool is capable of evaluating the undesired effects related to the use of low-cost manufacturing techniques, which are mostly due to the introduction of rounded corners in the cross section of the rectangular waveguides of the device. The obtained results show that, although stringent mechanical effects are imposed, it is possible to compensate for the impact of the cited low-cost manufacturing techniques by redesigning the matching elements considered in the original device. Several new designs concerning a great variety of E-plane components (such as right-angled bends, T-junctions and magic-Ts) are presented, and useful design guidelines are provided. The implemented tool, which is mainly based on the boundary integral-resonant mode expansion technique, has been successfully validated by comparing the obtained results to simulated data provided by a commercial software based on the finite element method.

Assessment of distributed solar power systems: Issues and impacts

NASA Astrophysics Data System (ADS)

Moyle, R. A.; Chernoff, H.; Schweizer, T. C.; Patton, J. B.

1982-11-01

The installation of distributed solar-power systems presents electric utilities with a host of questions. Some of the technical and economic impacts of these systems are discussed. Among the technical interconnect issues are isolated operation, power quality, line safety, and metering options. Economic issues include user purchase criteria, structures and installation costs, marketing and product distribution costs, and interconnect costs. An interactive computer program that allows easy calculation of allowable system prices and allowable generation-equipment prices was developed as part of this project. It is concluded that the technical problems raised by distributed solar systems are surmountable, but their resolution may be costly. The stringent purchase criteria likely to be imposed by many potential system users and the economies of large-scale systems make small systems (less than 10 to 20 kW) less attractive than larger systems. Utilities that consider life-cycle costs in making investment decisions and third-party investors who have tax and financial advantages are likely to place the highest value on solar-power systems.

Disease dynamics and costly punishment can foster socially imposed monogamy.

PubMed

Bauch, Chris T; McElreath, Richard

2016-04-05

Socially imposed monogamy in humans is an evolutionary puzzle because it requires costly punishment by those who impose the norm. Moreover, most societies were--and are--polygynous; yet many larger human societies transitioned from polygyny to socially imposed monogamy beginning with the advent of agriculture and larger residential groups. We use a simulation model to explore how interactions between group size, sexually transmitted infection (STI) dynamics and social norms can explain the timing and emergence of socially imposed monogamy. Polygyny dominates when groups are too small to sustain STIs. However, in larger groups, STIs become endemic (especially in concurrent polygynist networks) and have an impact on fertility, thereby mediating multilevel selection. Punishment of polygynists improves monogamist fitness within groups by reducing their STI exposure, and between groups by enabling punishing monogamist groups to outcompete polygynists. This suggests pathways for the emergence of socially imposed monogamy, and enriches our understanding of costly punishment evolution.

Disease dynamics and costly punishment can foster socially imposed monogamy

PubMed Central

Bauch, Chris T.; McElreath, Richard

2016-01-01

Socially imposed monogamy in humans is an evolutionary puzzle because it requires costly punishment by those who impose the norm. Moreover, most societies were—and are—polygynous; yet many larger human societies transitioned from polygyny to socially imposed monogamy beginning with the advent of agriculture and larger residential groups. We use a simulation model to explore how interactions between group size, sexually transmitted infection (STI) dynamics and social norms can explain the timing and emergence of socially imposed monogamy. Polygyny dominates when groups are too small to sustain STIs. However, in larger groups, STIs become endemic (especially in concurrent polygynist networks) and have an impact on fertility, thereby mediating multilevel selection. Punishment of polygynists improves monogamist fitness within groups by reducing their STI exposure, and between groups by enabling punishing monogamist groups to outcompete polygynists. This suggests pathways for the emergence of socially imposed monogamy, and enriches our understanding of costly punishment evolution. PMID:27044573

78 FR 20912 - Clean Water Act: Availability of List Decisions

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-08

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9798-8] Clean Water Act: Availability of List Decisions.... SUMMARY: The Clean Water Act requires that States periodically submit, and EPA approve or disapprove... are not stringent enough to attain or maintain State water quality standards and for which total...

43 CFR 420.12 - Requirements-operators.

Code of Federal Regulations, 2012 CFR

2012-10-01

... THE INTERIOR OFF-ROAD VEHICLE USE Operating Criteria § 420.12 Requirements—operators. (a) In addition... off-road vehicles; if State laws are lacking or less stringent than the regulations established in... operator of an off-road vehicle operated on Reclamation lands shall possess a valid motor vehicle operator...

43 CFR 420.12 - Requirements-operators.

Code of Federal Regulations, 2013 CFR

2013-10-01

... THE INTERIOR OFF-ROAD VEHICLE USE Operating Criteria § 420.12 Requirements—operators. (a) In addition... off-road vehicles; if State laws are lacking or less stringent than the regulations established in... operator of an off-road vehicle operated on Reclamation lands shall possess a valid motor vehicle operator...

43 CFR 420.12 - Requirements-operators.

Code of Federal Regulations, 2014 CFR

2014-10-01

... THE INTERIOR OFF-ROAD VEHICLE USE Operating Criteria § 420.12 Requirements—operators. (a) In addition... off-road vehicles; if State laws are lacking or less stringent than the regulations established in... operator of an off-road vehicle operated on Reclamation lands shall possess a valid motor vehicle operator...

The Dangers of Aestheticism in Schooling.

ERIC Educational Resources Information Center

Meager, Ruby

1981-01-01

Prompted by Immanuel Kant's analysis of the nature and operations of the imagination in his "Critique of the Aesthetical Judgment," this article points out the danger of encouraging imagination-borne aesthetical judgments and explanatory hypotheses. Concludes that understanding requires submission to more stringent standards of objectivity and to…

An Introduction to Modern Missing Data Analyses

ERIC Educational Resources Information Center

Baraldi, Amanda N.; Enders, Craig K.

2010-01-01

A great deal of recent methodological research has focused on two modern missing data analysis methods: maximum likelihood and multiple imputation. These approaches are advantageous to traditional techniques (e.g. deletion and mean imputation techniques) because they require less stringent assumptions and mitigate the pitfalls of traditional…

40 CFR 256.21 - Requirements for State regulatory powers.

Code of Federal Regulations, 2010 CFR

2010-07-01

... WASTES GUIDELINES FOR DEVELOPMENT AND IMPLEMENTATION OF STATE SOLID WASTE MANAGEMENT PLANS Solid Waste... be adequate to enforce solid waste disposal standards which are equivalent to or more stringent than the criteria for classification of solid waste disposal facilities (40 CFR part 257). Such authority...

40 CFR 256.21 - Requirements for State regulatory powers.

Code of Federal Regulations, 2011 CFR

2011-07-01

... WASTES GUIDELINES FOR DEVELOPMENT AND IMPLEMENTATION OF STATE SOLID WASTE MANAGEMENT PLANS Solid Waste... be adequate to enforce solid waste disposal standards which are equivalent to or more stringent than the criteria for classification of solid waste disposal facilities (40 CFR part 257). Such authority...

43 CFR 420.12 - Requirements-operators.

Code of Federal Regulations, 2010 CFR

2010-10-01

... snowmobiles, trail bikes, and any other off road vehicle the operator shall wear safety equipment, generally... THE INTERIOR OFF-ROAD VEHICLE USE Operating Criteria § 420.12 Requirements—operators. (a) In addition... off-road vehicles; if State laws are lacking or less stringent than the regulations established in...

43 CFR 420.12 - Requirements-operators.

Code of Federal Regulations, 2011 CFR

2011-10-01

... snowmobiles, trail bikes, and any other off road vehicle the operator shall wear safety equipment, generally... THE INTERIOR OFF-ROAD VEHICLE USE Operating Criteria § 420.12 Requirements—operators. (a) In addition... off-road vehicles; if State laws are lacking or less stringent than the regulations established in...

Using Common Planning Time to Foster Professional Learning

ERIC Educational Resources Information Center

Dever, Robin; Lash, Martha J.

2013-01-01

Increased emphasis on meeting state standards, more stringent requirements for designation as highly qualified, and intensified accountability for student performance have foisted new expectations upon teachers and stimulated changes in professional development models in which the greater urgency is clearly to attend to the teacher's role as…

Field dodder (Cuscuta campestris) control with flumioxazin

USDA-ARS?s Scientific Manuscript database

Field dodder is an important weed in alfalfa grown for seed production, requiring stringent control to keep the alfalfa seed free of dodder seed contamination. Pendimethalin has been the primary tool used to control dodder in alfalfa seed production for over 25 years. Flumioxazin was recently regis...

Stringency and relaxation among the halobacteria.

PubMed Central

Cimmino, C; Scoarughi, G L; Donini, P

1993-01-01

Accumulation of stable RNA and production of guanosine polyphosphates (ppGpp and pppGpp) were studied during amino acid starvation in four species of halobacteria. In two of the four species, stable RNA was under stringent control, whereas one of the remaining two species was relaxed and the other gave an intermediate phenotype. The stringent reaction was reversed by anisomycin, an effect analogous to the chloroamphenicol-induced reversal of stringency in the eubacteria. During the stringent response, neither ppGpp nor pppGpp accumulation took place during starvation. In both growing and starved cells a very low basal level of the two polyphosphates appeared to be present. In the stringent species the intracellular concentration of GTP did not diminish but actually increased during the course of the stringent response. These data demonstrate that (i) wild-type halobacteria can have either the stringent or the relaxed phenotype (all wild-type eubacteria tested have been shown to be stringent); (ii) stringency in the halobacteria is dependent on the deaminoacylation of tRNA, as in the eubacteria; and (iii) in the halobacteria, ppGpp is not an effector of stringent control over stable-RNA synthesis. Images PMID:7691798

Assessment of Logistics Effectiveness for Expeditionary Units

DTIC Science & Technology

2017-12-01

navigating the bureaucracy when spending government money requires the ESU teams to be savvy supply experts. Figure 8. EOD Force Laydown. Source...main uses is to help free a trapped diver from any number of hazards. The MK-16 equipment must withstand these conditions and not puncture...of the valves being shipped to the units as repair parts. The pieces require an oxygen- free environment for testing, along with other stringent

Latency in Visionic Systems: Test Methods and Requirements

NASA Technical Reports Server (NTRS)

Bailey, Randall E.; Arthur, J. J., III; Williams, Steven P.; Kramer, Lynda J.

2005-01-01

A visionics device creates a pictorial representation of the external scene for the pilot. The ultimate objective of these systems may be to electronically generate a form of Visual Meteorological Conditions (VMC) to eliminate weather or time-of-day as an operational constraint and provide enhancement over actual visual conditions where eye-limiting resolution may be a limiting factor. Empirical evidence has shown that the total system delays or latencies including the imaging sensors and display systems, can critically degrade their utility, usability, and acceptability. Definitions and measurement techniques are offered herein as common test and evaluation methods for latency testing in visionics device applications. Based upon available data, very different latency requirements are indicated based upon the piloting task, the role in which the visionics device is used in this task, and the characteristics of the visionics cockpit display device including its resolution, field-of-regard, and field-of-view. The least stringent latency requirements will involve Head-Up Display (HUD) applications, where the visionics imagery provides situational information as a supplement to symbology guidance and command information. Conversely, the visionics system latency requirement for a large field-of-view Head-Worn Display application, providing a Virtual-VMC capability from which the pilot will derive visual guidance, will be the most stringent, having a value as low as 20 msec.

Contamination monitoring approaches for EUV space optics

NASA Technical Reports Server (NTRS)

Ray, David C.; Malina, Roger F.; Welsh, Barry J.; Battel, Steven J.

1989-01-01

Data from contaminant-induced UV optics degradation studies and particulate models are used here to develop end-of-service-life instrument contamination requirements which are very stringent but achievable. The budget is divided into allocations for each phase of hardware processing. Optical and nonoptical hardware are monitored for particulate and molecular contamination during initial cleaning and baking, assembly, test, and calibration phases. The measured contamination levels are compared to the requirements developed for each phase to provide confidence that the required end-of-life levels will be met.

26 CFR 1.857-4 - Tax imposed by reason of the failure to meet certain source-of-income requirements.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Real Estate Investment.... Section 857(b)(5) imposes a tax on a real estate investment trust that is considered, by reason of section...

26 CFR 1.857-4 - Tax imposed by reason of the failure to meet certain source-of-income requirements.

Code of Federal Regulations, 2012 CFR

2012-04-01

..., DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Real Estate Investment.... Section 857(b)(5) imposes a tax on a real estate investment trust that is considered, by reason of section...

26 CFR 1.857-4 - Tax imposed by reason of the failure to meet certain source-of-income requirements.

Code of Federal Regulations, 2013 CFR

2013-04-01

..., DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Real Estate Investment.... Section 857(b)(5) imposes a tax on a real estate investment trust that is considered, by reason of section...

26 CFR 1.857-4 - Tax imposed by reason of the failure to meet certain source-of-income requirements.

Code of Federal Regulations, 2014 CFR

2014-04-01

..., DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Real Estate Investment.... Section 857(b)(5) imposes a tax on a real estate investment trust that is considered, by reason of section...

76 FR 65223 - Proposed Collection; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-20

..., however, may impose a burden. For an issuer to establish a QLCC, the QLCC must adopt written procedures... establish a QLCC.\\2\\ Establishing the written procedures required by the rule should not impose a... SECURITIES AND EXCHANGE COMMISSION Proposed Collection; Comment Request Upon Written Request...

Thermal Design to Meet Stringent Temperature Gradient/Stability Requirements of SWIFT BAT Detectors

NASA Technical Reports Server (NTRS)

Choi, Michael K.

2000-01-01

The Burst Alert Telescope (BAT) is an instrument on the National Aeronautics and Space Administration (NASA) SWIFT spacecraft. It is designed to detect gamma ray burst over a broad region of the sky and quickly align the telescopes on the spacecraft to the gamma ray source. The thermal requirements for the BAT detector arrays are very stringent. The maximum allowable temperature gradient of the 256 cadmium zinc telluride (CZT) detectors is PC. Also, the maximum allowable rate of temperature change of the ASICs of the 256 Detector Modules (DMs) is PC on any time scale. The total power dissipation of the DMs and Block Command & Data Handling (BCDH) is 180 W. This paper presents a thermal design that uses constant conductance heat pipes (CCHPs) to minimize the temperature gradient of the DMs, and loop heat pipes (LHPs) to transport the waste heat to the radiator. The LHPs vary the effective thermal conductance from the DMs to the radiator to minimize heater power to meet the heater power budget, and to improve the temperature stability. The DMs are cold biased, and active heater control is used to meet the temperature gradient and stability requirements.

76 FR 75913 - Notice of Lodging of Modification of Consent Decree Under the Clean Water Act

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-05

... (``Regulated Bacteria'') and to comply with interim effluent limitations for those pollutants. The proposed Modification provides new, more stringent interim effluent limitations for Regulated Bacteria and requires... effluent limitations for Regulated Bacteria set forth in the Facility's National Pollutant Discharge...

42 CFR 455.452 - Other State screening methods.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 4 2013-10-01 2013-10-01 false Other State screening methods. 455.452 Section 455....452 Other State screening methods. Nothing in this subpart must restrict the State Medicaid agency from establishing provider screening methods in addition to or more stringent than those required by...

42 CFR 455.452 - Other State screening methods.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 4 2011-10-01 2011-10-01 false Other State screening methods. 455.452 Section 455....452 Other State screening methods. Nothing in this subpart must restrict the State Medicaid agency from establishing provider screening methods in addition to or more stringent than those required by...

49 CFR 383.133 - Testing methods.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 5 2010-10-01 2010-10-01 false Testing methods. 383.133 Section 383.133... STANDARDS; REQUIREMENTS AND PENALTIES Tests § 383.133 Testing methods. (a) All tests shall be constructed in... must be at least as stringent as the Federal standards. (c) States shall determine specific methods for...

FY 2001 Pollution Prevention/Compliance, Acquisition and Technology Division Annual Report

DTIC Science & Technology

2002-02-15

readiness, save money and avoid bad decisions by knowing which alternative cleaning products meet its stringent requirements for performance, soldier...several cleaning products and gather data the Army and other DoD services can use to make procurement and usage decisions. The current program test

Fixed-Abrasive Grinding of Thin-Film Recording Heads Final Report CRADA No. TC-0498-93

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blaedel, K. L.; Newman, C.

The goals of this project were (1) to significantly reduce the cost of manufacturing thin-film recording heads for magnetic storage media and (2) to meet the stringent dimensional tolerances required for heads in the next generation high-density disc drives.

Evidence-Based Practices in Mentoring Students with Disabilities: Four Case Studies

ERIC Educational Resources Information Center

Stumbo, Norma J.; Martin, Jay K.; Nordstrom, Dan; Rolfe, Tina; Burgstahler, Sheryl; Whitney, Jean; Langley-Turnbaugh, Samantha; Lovewell, Lynn; Moeller, Babette; Larry, Randy; Misquez, Ed

2011-01-01

Individuals with disabilities are attending postsecondary institutions at higher rates than ever before, although many struggle to adjust in college environments. On one hand, higher education positively correlates with better employment outcomes, while on the other, higher education represents more stringent academic requirements and more…

Live, Online Short-Courses: A Case Study of Innovative Teacher Professional Development

ERIC Educational Resources Information Center

Marrero, Meghan E.; Woodruff, Karen A.; Schuster, Glen S.; Riccio, Jessica Fitzsimons

2010-01-01

Teachers are searching for new venues through which they may meet stringent professional development requirements. Under competitive funding from NASA's (National Aeronautics and Space Administration) Office of Education and the NASA Explorer Schools Project, U.S. Satellite Laboratory, Inc. created a series of live, online, interactive…

Documentation of 50% water conservation in a single process at a beef abattoir

USDA-ARS?s Scientific Manuscript database

Beef slaughter is water intensive due to stringent food safety requirements. We conducted a study at a commercial beef processor to demonstrate water conservation by modifying the mechanical head wash. We documented the initial nozzle configuration (112 nozzles), water pressure (275 kPa), and flowra...

Direct digital RF synthesis and modulation for MSAT mobile applications

NASA Technical Reports Server (NTRS)

Crozier, Stewart; Datta, Ravi; Sydor, John

1993-01-01

A practical method of performing direct digital RF synthesis using the Hilbert transform single sideband (SSB) technique is described. It is also shown that amplitude and phase modulation can be achieved directly at L-band with frequency stability and spurii performance exceeding stringent MSAT system requirements.

7 CFR 331.5 - Exemptions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... reported to APHIS or CDC by telephone, facsimile, or e-mail. This report must be followed by submission of APHIS/CDC Form 4 within 7 calendar days after identification. Less stringent reporting may be required during agricultural emergencies or outbreaks, or in endemic areas. A copy of APHIS/CDC Form 4 must be...

7 CFR 331.5 - Exemptions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... reported to APHIS or CDC by telephone, facsimile, or e-mail. This report must be followed by submission of APHIS/CDC Form 4 within 7 calendar days after identification. Less stringent reporting may be required during agricultural emergencies or outbreaks, or in endemic areas. A copy of APHIS/CDC Form 4 must be...

7 CFR 331.5 - Exemptions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... reported to APHIS or CDC by telephone, facsimile, or e-mail. This report must be followed by submission of APHIS/CDC Form 4 within 7 calendar days after identification. Less stringent reporting may be required during agricultural emergencies or outbreaks, or in endemic areas. A copy of APHIS/CDC Form 4 must be...

7 CFR 331.5 - Exemptions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... reported to APHIS or CDC by telephone, facsimile, or e-mail. This report must be followed by submission of APHIS/CDC Form 4 within 7 calendar days after identification. Less stringent reporting may be required during agricultural emergencies or outbreaks, or in endemic areas. A copy of APHIS/CDC Form 4 must be...

7 CFR 331.5 - Exemptions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... reported to APHIS or CDC by telephone, facsimile, or e-mail. This report must be followed by submission of APHIS/CDC Form 4 within 7 calendar days after identification. Less stringent reporting may be required during agricultural emergencies or outbreaks, or in endemic areas. A copy of APHIS/CDC Form 4 must be...

Opportunities for improving risk communication during the permitting process for entomophagous biological control agents: A review of current systems

USDA-ARS?s Scientific Manuscript database

Concerns about potentially irreversible non-target impacts from the importation and release of entomophagous biological control agents (BCAs) have resulted in increasingly stringent import requirements by National Plant Protection Organizations. Despite numerous scientific publications on the poten...

30 CFR 903.700 - Arizona Federal program.

Code of Federal Regulations, 2014 CFR

2014-07-01

... operations in Arizona conducted on non-Federal and non-Indian lands. To the extent required by 30 CFR part 740, this part also applies to surface coal mining and reclamation operations on Federal lands in... that the rules in this chapter establish more stringent environmental or land use controls: (1) The...

30 CFR 903.700 - Arizona Federal program.

Code of Federal Regulations, 2012 CFR

2012-07-01

... operations in Arizona conducted on non-Federal and non-Indian lands. To the extent required by 30 CFR part 740, this part also applies to surface coal mining and reclamation operations on Federal lands in... that the rules in this chapter establish more stringent environmental or land use controls: (1) The...

30 CFR 903.700 - Arizona Federal program.

Code of Federal Regulations, 2011 CFR

2011-07-01

... operations in Arizona conducted on non-Federal and non-Indian lands. To the extent required by 30 CFR part 740, this part also applies to surface coal mining and reclamation operations on Federal lands in... that the rules in this chapter establish more stringent environmental or land use controls: (1) The...

30 CFR 903.700 - Arizona Federal program.

Code of Federal Regulations, 2013 CFR

2013-07-01

... operations in Arizona conducted on non-Federal and non-Indian lands. To the extent required by 30 CFR part 740, this part also applies to surface coal mining and reclamation operations on Federal lands in... that the rules in this chapter establish more stringent environmental or land use controls: (1) The...

7 CFR 3430.42 - Special award conditions.

Code of Federal Regulations, 2010 CFR

2010-01-01

...) General. CSREES may, with respect to any award, impose additional conditions prior to or at the time of... needed; the time allowed for completing the corrective actions; and the method for requesting reconsideration of the additional requirements imposed. (c) Form CSREES-2009, Award Face Sheet. These special...

Field Testing of Compartmentalization Methods for Multifamily Construction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ueno, K.; Lstiburek, J. W.

2015-03-01

The 2012 International Energy Conservation Code (IECC) has an airtightness requirement of 3 air changes per hour at 50 Pascals test pressure (3 ACH50) for single-family and multifamily construction (in climate zones 3–8). The Leadership in Energy & Environmental Design certification program and ASHRAE Standard 189 have comparable compartmentalization requirements. ASHRAE Standard 62.2 will soon be responsible for all multifamily ventilation requirements (low rise and high rise); it has an exceptionally stringent compartmentalization requirement. These code and program requirements are driving the need for easier and more effective methods of compartmentalization in multifamily buildings.

Abatement of tropospheric ozone: effects of strategies to improve air quality on public health and other sectors.

PubMed

Guest, C S; Morgan, P; Moss, J R; Woodward, A J; McMichael, A J

1996-06-01

The National Health and Medical Research Council's air quality goal for ozone in the troposphere (near the earth's surface) is 0.12 parts per million (ppm), averaged over one hour, similar to the United States standard, but less stringent than the guideline for Europe. We aimed to identify the environmental, economic and social changes that would be associated with changing the goal. Methods included literature review, economic assessments and group interviews. The group to benefit from lower exposures may include outdoor workers, school children and people not in regular day-time work indoors, because ozone is most prevalent during the daylight hours of the warmer months. A lower level could improve the yield of some crops. The causes and effects of tropospheric ozone are not appreciated except among groups with relevant commercial, industrial or scientific experience. However, the consultations identified frustration about the social problems caused by dependence on private motor vehicles. Short-term costs of compliance with a more stringent goal would fall principally on the users of transport. The value of the benefits was enough for many to support making the ozone goal more stringent, but those who required a demonstration of financial benefit (even including savings of health care costs) did not support any change to the goal. Based primarily on averted detriment to health, we recommend the more stringent level of 0.08 ppm (one-hour average) as the goal for the year 2005 in Australia and elsewhere. The addition of a goal with longer averaging time is also proposed.

Integrated simulations of H-mode operation in ITER including core fuelling, divertor detachment and ELM control

NASA Astrophysics Data System (ADS)

Polevoi, A. R.; Loarte, A.; Dux, R.; Eich, T.; Fable, E.; Coster, D.; Maruyama, S.; Medvedev, S. Yu.; Köchl, F.; Zhogolev, V. E.

2018-05-01

ELM mitigation to avoid melting of the tungsten (W) divertor is one of the main factors affecting plasma fuelling and detachment control at full current for high Q operation in ITER. Here we derive the ITER operational space, where ELM mitigation to avoid melting of the W divertor monoblocks top surface is not required and appropriate control of W sources and radiation in the main plasma can be ensured through ELM control by pellet pacing. We apply the experimental scaling that relates the maximum ELM energy density deposited at the divertor with the pedestal parameters and this eliminates the uncertainty related with the ELM wetted area for energy deposition at the divertor and enables the definition of the ITER operating space through global plasma parameters. Our evaluation is thus based on this empirical scaling for ELM power loads together with the scaling for the pedestal pressure limit based on predictions from stability codes. In particular, our analysis has revealed that for the pedestal pressure predicted by the EPED1  +  SOLPS scaling, ELM mitigation to avoid melting of the W divertor monoblocks top surface may not be required for 2.65 T H-modes with normalized pedestal densities (to the Greenwald limit) larger than 0.5 to a level of current of 6.5–7.5 MA, which depends on assumptions on the divertor power flux during ELMs and between ELMs that expand the range of experimental uncertainties. The pellet and gas fuelling requirements compatible with control of plasma detachment, core plasma tungsten accumulation and H-mode operation (including post-ELM W transient radiation) have been assessed by 1.5D transport simulations for a range of assumptions regarding W re-deposition at the divertor including the most conservative assumption of zero prompt re-deposition. With such conservative assumptions, the post-ELM W transient radiation imposes a very stringent limit on ELM energy losses and the associated minimum required ELM frequency. Depending on W transport assumptions during the ELM, a maximum ELM frequency is also identified above which core tungsten accumulation takes place.

Polybrominated diphenyl ether (PBDE) concentrations and resulting exposure in homes in California: relationships among passive air, surface wipe and dust concentrations, and temporal variability

EPA Science Inventory

Polybrominated diphenyl ethers (PBDEs) are used as flame retardants in furniture foam, electronics, and other home furnishings. A field study was conducted that enrolled 139 households from California, which has had more stringent flame retardant requirements than other countries...

Polymeric additive performance in closed whitewater systems

Treesearch

T. H. Wegner

1984-01-01

“With more stringent requirements on discharge water quality and with escalating water treatment costs, water recycling within the paper mill is of growing importance. A serious problem resulting from more white-water recycling is reduced drainage and fiber or fines retention because of diminished polymeric additive performance. To provide better insight for overcoming...

Sensitivity and Specificity of Proposed DSM-5 Criteria for Autism Spectrum Disorder in Toddlers

ERIC Educational Resources Information Center

Barton, Marianne L.; Robins, Diana L.; Jashar, Dasal; Brennan, Laura; Fein, Deborah

2013-01-01

Autism spectrum disorder (ASD) diagnosis is based on behavioral presentation; changes in conceptual models or defining behaviors may significantly impact diagnosis and uptake of ASD-specific interventions. The literature examining impact of DSM-5 criteria is equivocal. Toddlers may be especially vulnerable to the stringent requirements of…

Cybersecurity Education: Bridging the Gap between Hardware and Software Domains

ERIC Educational Resources Information Center

Lukowiak, Marcin; Radziszowski, Stanislaw; Vallino, James; Wood, Christopher

2014-01-01

With the continuous growth of cyberinfrastructure throughout modern society, the need for secure computing and communication is more important than ever before. As a result, there is also an increasing need for entry-level developers who are capable of designing and building practical solutions for systems with stringent security requirements.…

Electrophoresis for biological production

NASA Technical Reports Server (NTRS)

Mccreight, L. R.

1977-01-01

Preparative electrophoresis may provide a unique method for meeting ever more stringent purity requirements. Prolonged near zero gravity in space may permit the operation of preparative electrophoresis equipment with 100 times greater throughput than is currently available. Some experiments with influenza Virus Antigen, Erythropoietin and Antihemophaliac Factor, along with process and economic projections, are briefly reviewed.

Parables and Politics: Clergy Attitudes toward Illegal Immigration in Alabama

ERIC Educational Resources Information Center

Wickersham, Mary Eleanor

2013-01-01

The passage of a stringent immigration law in Alabama in 2011 makes relevant the juxtaposition of clergy and congregant attitudes and behaviors toward illegal immigrants as related to Biblical teachings that require charity to aliens. In order to examine the relationship between religious attitudes and illegal immigration, approximately 426…

Making Academic OER Easy: Reflections on Technology and Openness at Oxford University

ERIC Educational Resources Information Center

Highton, Melissa; Fresen, Jill; Wild, Joanna

2011-01-01

Due to its stringent entry requirements, academic reputation and world ranking, Oxford University in the United Kingdom is perceived by some as being a closed, exclusive, and elitist institution. As learning technologists working in the institution, we have experienced an enthusiasm amongst academic colleagues for openness in publication and…

40 CFR 129.7 - Requirement and procedure for establishing a more stringent effluent limitation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... PROTECTION AGENCY (CONTINUED) WATER PROGRAMS TOXIC POLLUTANT EFFLUENT STANDARDS Toxic Pollutant Effluent...) determines that the ambient water criterion established in these standards is not being met or will not be met in the receiving water as a result of one or more discharges at levels allowed by these standards...

75 FR 48579 - Approval and Promulgation of Implementation Plans; State of Missouri

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-11

.... Louis area. The state has a statewide fugitive dust rule, 10 CSR 10-6.170, which contains similar... fugitive dust rule is as stringent as the requirements in the rescinded area rule and this action would not... longer in operation, and because the state's statewide fugitive dust rule contains similar restrictions...

40 CFR 146.15 - Class I municipal disposal well alternative authorization in certain parts of Florida.

Code of Federal Regulations, 2010 CFR

2010-07-01

... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) UNDERGROUND INJECTION CONTROL PROGRAM... ground water monitoring data generated pursuant to regulatory requirements governing operation of Class I...-600.420(1)(d), and using high-level disinfection in a manner that is no less stringent than the...

40 CFR 146.15 - Class I municipal disposal well alternative authorization in certain parts of Florida.

Code of Federal Regulations, 2012 CFR

2012-07-01

... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) UNDERGROUND INJECTION CONTROL PROGRAM... ground water monitoring data generated pursuant to regulatory requirements governing operation of Class I...-600.420(1)(d), and using high-level disinfection in a manner that is no less stringent than the...

40 CFR 146.15 - Class I municipal disposal well alternative authorization in certain parts of Florida.

Code of Federal Regulations, 2011 CFR

2011-07-01

... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) UNDERGROUND INJECTION CONTROL PROGRAM... ground water monitoring data generated pursuant to regulatory requirements governing operation of Class I...-600.420(1)(d), and using high-level disinfection in a manner that is no less stringent than the...

40 CFR 146.15 - Class I municipal disposal well alternative authorization in certain parts of Florida.

Code of Federal Regulations, 2013 CFR

2013-07-01

... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) UNDERGROUND INJECTION CONTROL PROGRAM... ground water monitoring data generated pursuant to regulatory requirements governing operation of Class I...-600.420(1)(d), and using high-level disinfection in a manner that is no less stringent than the...

40 CFR 146.15 - Class I municipal disposal well alternative authorization in certain parts of Florida.

Code of Federal Regulations, 2014 CFR

2014-07-01

... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) UNDERGROUND INJECTION CONTROL PROGRAM... ground water monitoring data generated pursuant to regulatory requirements governing operation of Class I...-600.420(1)(d), and using high-level disinfection in a manner that is no less stringent than the...

77 FR 1895 - Revisions to the California State Implementation Plan, South Coast Air Quality Management District

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-12

... approve South Coast Air Quality Management District (SCAQMD) Rule 317, ``Clean Air Act Non- Attainment Fee... Rule 317, an equivalent alternative program, is not less stringent than the program required by section... equivalent alternative programs, and, if so, whether Rule 317 would constitute an approvable equivalent...

77 FR 74372 - Revisions to the California State Implementation Plan, South Coast Air Quality Management District

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-14

... of South Coast Air Quality Management District (SCAQMD) Rule 317, ``Clean Air Act Non- Attainment Fee... determined that SCAQMD's alternative fee-equivalent program is not less stringent than the program required by section 185, and, therefore, is approvable as an equivalent alternative program, consistent with...

76 FR 25569 - Defense Federal Acquisition Regulation Supplement; Minimizing the Use of Materials Containing...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-05

..., therefore, this action establishes requirements that DoD personnel must follow when making acquisitions for...) ten-fold from 52 to 5 micrograms-per-cubic-meter, making it among the most stringently regulated... officer will forward the request to the authorized approving official (DFARS 223.7305(a)) for decision...

Documentation of 50% water conservation in a single process at a beef abattoir. Meat Science

USDA-ARS?s Scientific Manuscript database

Beef slaughter is water intensive due to stringent food safety requirements. We conducted a study at a commercial beef processor to demonstrate water conservation by modifying the mechanical head wash. We documented the initial nozzle configuration (112 nozzles), water pressure (275 kPa), and flowra...

All-optical photoacoustic microscopy (AOPAM) system for remote characterization of biological tissues

NASA Astrophysics Data System (ADS)

Sampathkumar, Ashwin; Chitnis, Parag V.; Silverman, Ronald H.

2014-03-01

Conventional photoacoustic microscopy (PAM) employs light pulses to produce a photoacoustic (PA) effect and detects the resulting acoustic waves using an ultrasound transducer acoustically coupled to the target. The resolution of conventional PAM is limited by the sensitivity and bandwidth of the ultrasound transducer. We investigated a versatile, all-optical PAM (AOPAM) system for characterizing in vivo as well as ex vivo biological specimens. The system employs non-contact interferometric detection of PA signals that overcomes limitations of conventional PAM. A 532-nm pump laser with a pulse duration of 5 ns excites the PA effect in tissue. Resulting acoustic waves produce surface displacements that are sensed using a 532-nm continuous-wave (CW) probe laser in a Michelson interferometer with a 1- GHz bandwidth. The pump and probe beams are coaxially focused using a 50X objective giving a diffraction-limited spot size of 0.48 μm. The phase-encoded probe beam is demodulated using homodyne methods. The detected timedomain signal is time reversed using k-space wave-propagation methods to produce a spatial distribution of PA sources in the target tissue. A minimum surface-displacement sensitivity of 0.19 pm was measured. PA-induced surface displacements are very small; therefore, they impose stringent detection requirements and determine the feasibility of implementing an all-optical PAM in biomedical applications. 3D PA images of ex vivo porcine retina specimens were generated successfully. We believe the AOPAM system potentially is well suited for assessing retinal diseases and other near-surface biomedical applications such as sectionless histology and evaluation of skin burns and pressure or friction ulcers.

Aerobic biological treatment of low-strength synthetic wastewater in membrane-coupled bioreactors: the structure and function of bacterial enrichment cultures as the net growth rate approaches zero.

PubMed

Chen, Ruoyu; LaPara, Timothy M

2006-01-01

The goal of the current research was to determine if the stringent nutrient limitation imposed by membrane-coupled bioreactors (MBRs) could be used to force mixed bacterial communities to exhibit a zero net growth rate over an extended time period. Mechanistically, this zero net growth rate could be achieved when the amount of energy available for growth is balanced by the maintenance requirements of the bacterial community. Bench-scale MBRs were fed synthetic feed medium containing gelatin as the major organic substrate. Biomass concentrations initially increased rapidly, but subsequently declined until an asymptote was reached. Leucine aminopeptidase activities concomitantly increased by at least 10-fold, suggesting that bacterial catabolic activity remained high even while growth rates became negligible. In contrast, alpha-glucosidase and heptanoate esterase activities decreased, indicating that the bacterial community specifically adapted to the carbon source in the feed medium. Bacterial community analysis by denaturing gradient gel electrophoresis of PCR-amplified 16S rRNA gene fragments (PCR-DGGE) suggested that the bacterial community structure completely changed from the beginning to the end of each MBR. Excision and nucleotide sequence analysis of prominent PCR-DGGE bands suggested that many of the dominant populations were similar to novel bacterial strains that were previously uncultivated or recently cultivated during studies specifically targeting these novel populations. This research demonstrates that MBRs have substantial practical applications for biological wastewater treatment; in addition, MBRs are a useful tool to study the ecology of slow-growing bacteria.

Space Construction Automated Fabrication Experiment Definition Study (SCAFEDS). Volume 3: Requirements

NASA Technical Reports Server (NTRS)

1978-01-01

The performance, design, and verification requirements for the space construction automated fabrication experiment (SCAFE) are defined and the source of each imposed or derived requirement is identified.

Pointing and tracking space mechanism for laser communication

NASA Technical Reports Server (NTRS)

Brunschvig, A.; Deboisanger, M.

1994-01-01

Space optical communication is considered a promising technology regarding its high data rate and confidentiality capabilities. However, it requires today complex satellite systems involving highly accurate mechanisms. This paper aims to highlight the stringent requirements which had to be fulfilled for such a mechanism, the way an existing design has been adapted to meet these requirements, and the main technical difficulties which have been overcome thanks to extensive development tests throughout the C/D phase initiated in 1991. The expected on-orbit performance of this mechanism is also presented.

77 FR 13491 - Approval and Promulgation of Implementation Plans and Designations of Areas for Air Quality...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-07

..., Douglas, Fayette, Forsyth, Fulton, Gwinnett, Hall, Henry, Newton, Paulding, Rockdale, Spalding and Walton... would not impose additional requirements beyond those imposed by state law. For that reason, this action... substantial direct costs on tribal governments or preempt tribal law. The Congressional Review Act, 5 U.S.C...

29 CFR 1926.451 - General requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... least 4 times the maximum intended load applied or transmitted to it. (2) Direct connections to roofs... resisting at least 4 times the tipping moment imposed by the scaffold operating at the rated load of the hoist, or 1.5 (minimum) times the tipping moment imposed by the scaffold operating at the stall load of...

29 CFR 1926.451 - General requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... least 4 times the maximum intended load applied or transmitted to it. (2) Direct connections to roofs... resisting at least 4 times the tipping moment imposed by the scaffold operating at the rated load of the hoist, or 1.5 (minimum) times the tipping moment imposed by the scaffold operating at the stall load of...

29 CFR 1926.451 - General requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... least 4 times the maximum intended load applied or transmitted to it. (2) Direct connections to roofs... resisting at least 4 times the tipping moment imposed by the scaffold operating at the rated load of the hoist, or 1.5 (minimum) times the tipping moment imposed by the scaffold operating at the stall load of...

29 CFR 1926.451 - General requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... least 4 times the maximum intended load applied or transmitted to it. (2) Direct connections to roofs... resisting at least 4 times the tipping moment imposed by the scaffold operating at the rated load of the hoist, or 1.5 (minimum) times the tipping moment imposed by the scaffold operating at the stall load of...

29 CFR 1926.451 - General requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... least 4 times the maximum intended load applied or transmitted to it. (2) Direct connections to roofs... resisting at least 4 times the tipping moment imposed by the scaffold operating at the rated load of the hoist, or 1.5 (minimum) times the tipping moment imposed by the scaffold operating at the stall load of...

31 CFR 10.35 - Requirements for covered opinions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... or evasion of any tax imposed by the Internal Revenue Code if the written advice— (1) Is a reliance... the avoidance or evasion of any tax imposed by the Internal Revenue Code if that purpose exceeds any... concerning one or more Federal tax issues arising from— (A) A transaction that is the same as or...

14 CFR 382.55 - May carriers impose security screening procedures for passengers with disabilities that go beyond...

Code of Federal Regulations, 2013 CFR

2013-01-01

... Accessibility of Airport Facilities § 382.55 May carriers impose security screening procedures for passengers..., including those with disabilities, are subject to TSA security screening requirements at U.S. airports. In addition, passengers at foreign airports, including those with disabilities, may be subject to security...

14 CFR 382.55 - May carriers impose security screening procedures for passengers with disabilities that go beyond...

Code of Federal Regulations, 2014 CFR

2014-01-01

... Accessibility of Airport Facilities § 382.55 May carriers impose security screening procedures for passengers..., including those with disabilities, are subject to TSA security screening requirements at U.S. airports. In addition, passengers at foreign airports, including those with disabilities, may be subject to security...

14 CFR 382.55 - May carriers impose security screening procedures for passengers with disabilities that go beyond...

Code of Federal Regulations, 2012 CFR

2012-01-01

... Accessibility of Airport Facilities § 382.55 May carriers impose security screening procedures for passengers..., including those with disabilities, are subject to TSA security screening requirements at U.S. airports. In addition, passengers at foreign airports, including those with disabilities, may be subject to security...

The many faces of competency.

PubMed

Drane, J F

1985-04-01

A sliding-scale model for assessing patient competency to consent to medical treatments is proposed. The least stringent standard, to be applied in the case of safe and effective treatments, assumes a valid consent if the patient is aware of what is happening and assents to the rational expectations of the physician. The second standard, applicable in the case of less certain treatments, requires that the patient understand the treatment options and have the capacity to choose or reject a treatment based on a weighing of risks and benefits. The third and most stringent standard, reserved for very dangerous treatments, bases competence to consent on an appreciation of the implications of the medical information for the patient's life and on an ability to state the reasons for the decision in terms of the medical issues and the patient's personal values.

The impact of multiple show-ups on eyewitness decision-making and innocence risk.

PubMed

Smith, Andrew M; Bertrand, Michelle; Lindsay, R C L; Kalmet, Natalie; Grossman, Deborah; Provenzano, Daniel

2014-09-01

If an eyewitness rejects a show-up, police may respond by finding a new suspect and conducting a second show-up with the same eyewitness. Police may continue finding suspects and conducting show-ups until the eyewitness makes an identification (Study 1). Relatively low criterion-setting eyewitnesses filter themselves out of the multiple show-ups procedure by choosing the first suspect with whom they are presented (Studies 2 and 3). Accordingly, response bias was more stringent on the second show-up when compared with the first, but became no more stringent with additional show-ups. Despite this stringent shift in response bias, innocence risk increased with additional show-ups, as false alarms cumulate (Studies 2 and 3). Although unbiased show-up instructions decreased innocent suspect identifications, the numbers were still discouraging (Study 4). Given the high number of innocent suspects who would be mistakenly identified through the use of multiple show-up procedures, using such identifications as evidence of guilt is questionable. Although evidence of guilt is limited to identifications from a single show-up, practical constraints might sometimes require police to use additional show-ups. Accordingly, we propose a stronger partition between evidentiary and investigative procedures. PsycINFO Database Record (c) 2014 APA, all rights reserved.

The Stringent Response Controls Catalases in Pseudomonas aeruginosa and Is Required for Hydrogen Peroxide and Antibiotic Tolerance

PubMed Central

Khakimova, Malika; Ahlgren, Heather G.; Harrison, Joe J.; English, Ann M.

2013-01-01

Pseudomonas aeruginosa, a human opportunistic pathogen, possesses a number of antioxidant defense enzymes under the control of multiple regulatory systems. We recently reported that inactivation of the P. aeruginosa stringent response (SR), a starvation stress response controlled by the alarmone (p)ppGpp, caused impaired antioxidant defenses and antibiotic tolerance. Since catalases are key antioxidant enzymes in P. aeruginosa, we compared the levels of H2O2 susceptibility and catalase activity in P. aeruginosa wild-type and ΔrelA ΔspoT (ΔSR) mutant cells. We found that the SR was required for optimal catalase activity and mediated H2O2 tolerance during both planktonic and biofilm growth. Upon amino acid starvation, induction of the SR upregulated catalase activity. Full expression of katA and katB also required the SR, and this regulation occurred through both RpoS-independent and RpoS-dependent mechanisms. Furthermore, overexpression of katA was sufficient to restore H2O2 tolerance and to partially rescue the antibiotic tolerance of ΔSR cells. All together, these results suggest that the SR regulates catalases and that this is an important mechanism in protecting nutrient-starved and biofilm bacteria from H2O2- and antibiotic-mediated killing. PMID:23457248

Metallization problems with concentrator cells

NASA Technical Reports Server (NTRS)

Iles, P. A.

1983-01-01

Cells used with concentrators have similar contact requirements to other cells, but operation at high intensity imposes more than the usual demands on the metallization. Overall contact requirements are listed and concentrator cell requirements are discussed.

Performance limitations of bilateral force reflection imposed by operator dynamic characteristics

NASA Technical Reports Server (NTRS)

Chapel, Jim D.

1989-01-01

A linearized, single-axis model is presented for bilateral force reflection which facilitates investigation into the effects of manipulator, operator, and task dynamics, as well as time delay and gain scaling. Structural similarities are noted between this model and impedance control. Stability results based upon this model impose requirements upon operator dynamic characteristics as functions of system time delay and environmental stiffness. An experimental characterization reveals the limited capabilities of the human operator to meet these requirements. A procedure is presented for determining the force reflection gain scaling required to provide stability and acceptable operator workload. This procedure is applied to a system with dynamics typical of a space manipulator, and the required gain scaling is presented as a function of environmental stiffness.

40 CFR 281.36 - Out-of-service UST systems and closure.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 28 2013-07-01 2013-07-01 false Out-of-service UST systems and closure... § 281.36 Out-of-service UST systems and closure. In order to be considered no less stringent than the... and corrective action requirements must be complied with. (c) All UST systems taken out of service...

40 CFR 281.36 - Out-of-service UST systems and closure.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 27 2014-07-01 2014-07-01 false Out-of-service UST systems and closure... § 281.36 Out-of-service UST systems and closure. In order to be considered no less stringent than the... and corrective action requirements must be complied with. (c) All UST systems taken out of service...

40 CFR 281.36 - Out-of-service UST systems and closure.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Out-of-service UST systems and closure... § 281.36 Out-of-service UST systems and closure. In order to be considered no less stringent than the... and corrective action requirements must be complied with. (c) All UST systems taken out of service...

40 CFR 281.36 - Out-of-service UST systems and closure.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 27 2011-07-01 2011-07-01 false Out-of-service UST systems and closure... § 281.36 Out-of-service UST systems and closure. In order to be considered no less stringent than the... and corrective action requirements must be complied with. (c) All UST systems taken out of service...

40 CFR 281.36 - Out-of-service UST systems and closure.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 28 2012-07-01 2012-07-01 false Out-of-service UST systems and closure... § 281.36 Out-of-service UST systems and closure. In order to be considered no less stringent than the... and corrective action requirements must be complied with. (c) All UST systems taken out of service...

Diving into Data: Developing the Capacity for Data Literacy in Teacher Education

ERIC Educational Resources Information Center

Dunlap, Karen; Piro, Jody S.

2016-01-01

Educators by definition are now required to utilize a variety of student data to shape the decisions they make and design the lessons they teach. As accountability standards become more stringent and as teachers face increasingly diverse student populations within their classrooms, they often struggle to adequately meet the needs of all learners.…

78 FR 8361 - Flightcrew Member Duty and Rest Requirements; Technical Correction

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-06

...). Because these short-call-reserve limits were not intended to be more stringent than flight-duty-period... short-call reserve to have the same extension as a flight duty period. Accordingly, in the final rule... [Docket No. FAA-2009-1093; Amdt. Nos. 117-1, 119-16, 121-357] RIN 2120-AJ58 Flightcrew Member Duty and...

Engineering Design Handbook. Breech Mechanism Design

DTIC Science & Technology

1979-02-01

4-22 4-11.2 Tool and Gage Requirements ...................................... 4-22 R eferences...16 4-5 Total Cost per Piece---Sum of Tool Costs, Machining Cost, and Nonproductive Cost ....................................................... 4-20 4...practical design limits are end of the gun tube from which the projectile numerous as well as stringent Today, the multi- emerges and the breecb end is that

Limiting Central Government Budget Deficits: International Experiences

DTIC Science & Technology

2010-03-11

Economic Cooperation and Development ( OECD ) countries, limit their fiscal deficits. Financial markets support government efforts to reduce deficit...fiscal consolidation efforts and developing medium-term budgetary frameworks for fiscal planning . Fiscal consolidation efforts, however, generally...require policymakers to weigh the effects of various policy trade-offs, including the trade-off between adopting stringent, but enforceable, rules- based

16 CFR 682.4 - Relation to other laws.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 16 Commercial Practices 1 2011-01-01 2011-01-01 false Relation to other laws. 682.4 Section 682.4... INFORMATION AND RECORDS § 682.4 Relation to other laws. Nothing in the rule in this part shall be construed... imposed under other law; or (b) To alter or affect any requirement imposed under any other provision of...

16 CFR 682.4 - Relation to other laws.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 16 Commercial Practices 1 2012-01-01 2012-01-01 false Relation to other laws. 682.4 Section 682.4... INFORMATION AND RECORDS § 682.4 Relation to other laws. Nothing in the rule in this part shall be construed... imposed under other law; or (b) To alter or affect any requirement imposed under any other provision of...

From Conventional Wisdom to Higher Education Transformation: Does It Take a Crisis to Make Fundamental Change?

ERIC Educational Resources Information Center

Kaufman, Roger

2010-01-01

With huge financial challenges being imposed on higher education, some react to crises to make changes and meet financial requirements. Changes are made that would be unthinkable without imposed demands. Two examples of universities that successfully responded to limited budgets to make major changes in organization, structure, and programs are…

Robust, Optimal Subsonic Airfoil Shapes

NASA Technical Reports Server (NTRS)

Rai, Man Mohan

2014-01-01

A method has been developed to create an airfoil robust enough to operate satisfactorily in different environments. This method determines a robust, optimal, subsonic airfoil shape, beginning with an arbitrary initial airfoil shape, and imposes the necessary constraints on the design. Also, this method is flexible and extendible to a larger class of requirements and changes in constraints imposed.

Testing Cobol Programs by Mutation. Volume II. CMS 1 System Documentation,

DTIC Science & Technology

1980-02-01

8217 LOOP MVth a’ solution was to enebese the macn depesi- 1F rumen Tom dent imes ide a apeelal type of mdulo called a G aaraadom(2); device maul* (see...software status register can be modified at will, while the required, but as an additional benefit, Modula contents of the buffer can be dealt with as...language. The requirements are stringent and usu- Dick up the contents of the address by Indirect ally the work Is never completed, an the uses for

SS/RCS surface tension propellant acquisition/expulsion tankage technology

NASA Technical Reports Server (NTRS)

1975-01-01

The analysis, design, fabrication, and testing of a propellant tank that satisfies the requirements of the space shuttle is presented. This mission presents very stringent and sometimes conflicting requirements. A compartmented-tank device was developed and various ground and drop tower test techniques were employed to verify the design using both subscale and full-scale hardware. Performance was established with scale models and further substantiation was obtained with the full-scale tankage. Fabrication, acceptance, fill and drain, inspection, and other ground handling procedures were developed.

End User Acceptance - Requirements or Specifications, Certification, Testing

NASA Technical Reports Server (NTRS)

Jeevarajan, Judith

2013-01-01

NASA follows top level safety requirement of two-failure tolerance (t hree levels of controls or design for minimum risk) to all catastroph ic hazards in the design of safe li-ion batteries for space use. ? R igorous development testing at appropriate levels to credible offnominal conditions and review of test data. ? Implement robust design con trols based on test results and test again to confirm safety at the a ppropriate levels. ? Stringent testing of all (100%) flight batteries (from button cells to large batteries).

17-4 PH and 15-5 PH

NASA Technical Reports Server (NTRS)

Johnson, Howard T.

1995-01-01

17-4 PH and 15-5 PH are extremely useful and versatile precipitation-hardening stainless steels. Armco 17-4 PH is well suited for the magnetic particle inspection requirements of Aerospace Material Specification. Armco 15-5 PH and 17-4 PH are produced in billet, plate, bar, and wire. Also, 15-5 PH is able to meet the stringent mechanical properties required in the aerospace and nuclear industries. Both products are easy to heat treat and machine, making them very useful in many applications.

Supersymmetric B – L inflation near the conformal coupling

DOE PAGES

Arai, Masato; Kawai, Shinsuke; Okada, Nobuchika

2014-06-01

We investigate a novel scenario of cosmological inflation in a gauged B-L extended minimal supersymmetric Standard Model with R-symmetry. We use a noncanonical Kähler potential and a superpotential, both preserving the R-symmetry to construct a model of slow-roll inflation. The model is controlled by two real parameters: the nonminimal coupling ξ that originates from the Kähler potential, and the breaking scale v of the U (1)B-L symmetry. We compute the spectrum of the cosmological microwave background radiation and show that the prediction of the model fits well the recent Planck satellite observation for a wide range of the parameter space.more » We also find that the typical reheating temperature of the model is low enough to avoid the gravitino problem but nevertheless allows sufficient production of the baryon asymmetry if we take into account the effect of resonance enhancement. The model is free from cosmic strings that impose stringent constraints on generic U (1)B-L based scenarios, as in our scenario the U (1)B-L symmetry is broken from the onset.« less

Innovative zoning to support equine influenza eradication from New South Wales, Australia.

PubMed

Scott-Orr, H

2011-07-01

Following detection of equine influenza (EI) in New South Wales, a complete standstill was imposed the next morning on the movement of all horses and donkeys within the state. Premises' biosecurity guidelines became progressively more stringent with time in an effort to stop local spread. The standstill was highly effective as a primary response to stop EI becoming widespread across Australia, but did not prevent spread to properties contiguous to infected premises in areas of high horse density and small property size, nor transmission by fomites nor possible local airborne transmission. Within 2 weeks of the start of the outbreak, a zoning system of Purple (Special Restricted), Red (Restricted), Amber (Control), and Green (Protected) Zones was implemented, and progressively modified as disease distribution changed. The colour coding system proved to be an easy way to communicate zone changes, the approximate level of disease risk and the stringency of movement restrictions to the general public and should be adopted more generally in AUSVETPLAN. © 2011 The Author. Australian Veterinary Journal © 2011 Australian Veterinary Association.

Austerity: a failed experiment on the people of Europe.

PubMed

McKee, Martin; Karanikolos, Marina; Belcher, Paul; Stuckler, David

2012-08-01

Many governments in Europe, either of their own volition or at the behest of the international financial institutions, have adopted stringent austerity policies in response to the financial crisis. By contrast, the USA launched a financial stimulus. The results of these experiments are now clear: the American economy is growing and those European countries adopting austerity, including the UK, Ireland, Greece, Portugal and Spain, are stagnating and struggling to repay rising debts. An initial recovery in the UK was halted once austerity measures hit. However, austerity has been not only an economic failure, but also a health failure, with increasing numbers of suicides and, where cuts in health budgets are being imposed, increasing numbers of people being unable to access care. Yet their stories remain largely untold. Here, we argue that there is an alternative to austerity, but that ideology is triumphing over evidence. Our paper was written to contribute to discussions among health policy leaders in Europe that will take place at the 15th European Health Forum at Gastein in October 2012, as its theme 'Crisis and Opportunity - Health in an Age of Austerity'.

Spacecraft fault tolerance: The Magellan experience

NASA Technical Reports Server (NTRS)

Kasuda, Rick; Packard, Donna Sexton

1993-01-01

Interplanetary and earth orbiting missions are now imposing unique fault tolerant requirements upon spacecraft design. Mission success is the prime motivator for building spacecraft with fault tolerant systems. The Magellan spacecraft had many such requirements imposed upon its design. Magellan met these requirements by building redundancy into all the major subsystem components and designing the onboard hardware and software with the capability to detect a fault, isolate it to a component, and issue commands to achieve a back-up configuration. This discussion is limited to fault protection, which is the autonomous capability to respond to a fault. The Magellan fault protection design is discussed, as well as the developmental and flight experiences and a summary of the lessons learned.

24 CFR 5.524 - Compliance with nondiscrimination requirements.

Code of Federal Regulations, 2010 CFR

2010-04-01

... the restrictions on use of assisted housing by noncitizens with ineligible immigration status imposed by this part in conformity with all applicable nondiscrimination and equal opportunity requirements...

Do we need a special ethics for research?

PubMed

Hansson, Sven Ove

2011-03-01

Research is subject to more stringent ethical requirements than most other human activities, and a procedure that is otherwise allowed may be forbidden in research. Hence, risk-taking is more restricted in scientific research than in most non-research contexts, and privacy is better protected in scientific questionnaires than in marketing surveys. Potential arguments for this difference are scrutinized. The case in its favour appears to be weak. A stronger case can be made in favour of a difference in the opposite direction: If perilous or otherwise problematic activities have to be performed it is usually better to perform them in a research context where they are properly evaluated so that guidance is obtained for the future. However, retreating from current ethical demands on research is not a desirable direction to go. Instead, research ethics can serve to inspire the introduction of more stringent ethical principles in other social sectors.

Nitrogen stress response and stringent response are coupled in Escherichia coli

PubMed Central

Brown, Daniel R.; Barton, Geraint; Pan, Zhensheng; Buck, Martin; Wigneshweraraj, Sivaramesh

2014-01-01

Assimilation of nitrogen is an essential process in bacteria. The nitrogen regulation stress response is an adaptive mechanism used by nitrogen-starved Escherichia coli to scavenge for alternative nitrogen sources and requires the global transcriptional regulator NtrC. In addition, nitrogen-starved E. coli cells synthesize a signal molecule, guanosine tetraphosphate (ppGpp), which serves as an effector molecule of many processes including transcription to initiate global physiological changes, collectively termed the stringent response. The regulatory mechanisms leading to elevated ppGpp levels during nutritional stresses remain elusive. Here, we show that transcription of relA, a key gene responsible for the synthesis of ppGpp, is activated by NtrC during nitrogen starvation. The results reveal that NtrC couples these two major bacterial stress responses to manage conditions of nitrogen limitation, and provide novel mechanistic insights into how a specific nutritional stress leads to elevating ppGpp levels in bacteria. PMID:24947454

Solar Heating And Cooling Of Buildings (SHACOB): Requirements definition and impact analysis-2. Volume 1: Energy-conserving design for residential structures

NASA Astrophysics Data System (ADS)

Cretcher, C. K.

1980-11-01

The impact of stringent energy conserving building standards on electric utility service areas and their customers was analyzed. The demands on the seven broadly representative electric utilities were aggregated to represent the total new construction electric heating demands in the years 1990 and 2000 to be compared to the aggregate obtained similarly for a nominal, less stringent standard, viz., ASHRAE 90-75. Results presented include the percentage of energy savings achieved in both heating and cooling seasons and typical demand profile changes. A utility economic impact analysis was performed for the cases investigated to determine changes in operating costs and potential capacity sales. A third cost component considered is the incremental cost of superinsulation (over ASHRAE 90-75) to the customer. The aggregate net cost to the utility/customer entity is utilized as a measure of overall economic benefit.

10 CFR 20.2302 - Additional requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 1 2012-01-01 2012-01-01 false Additional requirements. 20.2302 Section 20.2302 Energy NUCLEAR REGULATORY COMMISSION STANDARDS FOR PROTECTION AGAINST RADIATION Exemptions and Additional Requirements § 20.2302 Additional requirements. The Commission may, by rule, regulation, or order, impose...

10 CFR 20.2302 - Additional requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 1 2014-01-01 2014-01-01 false Additional requirements. 20.2302 Section 20.2302 Energy NUCLEAR REGULATORY COMMISSION STANDARDS FOR PROTECTION AGAINST RADIATION Exemptions and Additional Requirements § 20.2302 Additional requirements. The Commission may, by rule, regulation, or order, impose...

10 CFR 20.2302 - Additional requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Additional requirements. 20.2302 Section 20.2302 Energy NUCLEAR REGULATORY COMMISSION STANDARDS FOR PROTECTION AGAINST RADIATION Exemptions and Additional Requirements § 20.2302 Additional requirements. The Commission may, by rule, regulation, or order, impose...

77 FR 17105 - Identification of Interstate Motor Vehicles: City of Chicago, IL Registration Emblem Requirement...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-23

...-0086] Identification of Interstate Motor Vehicles: City of Chicago, IL Registration Emblem Requirement...) requesting a determination that the Commercial Motor Vehicle (CMV) identification requirement imposed by the... categories of excepted requirements. The first includes identification requirements related to motor vehicle...

29 CFR Appendix C to Subpart P of... - Timber Shoring for Trenches

Code of Federal Regulations, 2011 CFR

2011-07-01

.... Stable rock is exempt from shoring requirements and therefore, no data are presented for this condition... § 1926.652. (A) When loads imposed by structures or by stored material adjacent to the trench weigh in excess of the load imposed by a two-foot soil surcharge. The term “adjacent” as used here means the area...

29 CFR Appendix C to Subpart P of... - Timber Shoring for Trenches

Code of Federal Regulations, 2012 CFR

2012-07-01

.... Stable rock is exempt from shoring requirements and therefore, no data are presented for this condition... § 1926.652. (A) When loads imposed by structures or by stored material adjacent to the trench weigh in excess of the load imposed by a two-foot soil surcharge. The term “adjacent” as used here means the area...

29 CFR Appendix C to Subpart P of... - Timber Shoring for Trenches

Code of Federal Regulations, 2013 CFR

2013-07-01

.... Stable rock is exempt from shoring requirements and therefore, no data are presented for this condition... § 1926.652. (A) When loads imposed by structures or by stored material adjacent to the trench weigh in excess of the load imposed by a two-foot soil surcharge. The term “adjacent” as used here means the area...

29 CFR Appendix C to Subpart P of... - Timber Shoring for Trenches

Code of Federal Regulations, 2010 CFR

2010-07-01

.... Stable rock is exempt from shoring requirements and therefore, no data are presented for this condition... § 1926.652. (A) When loads imposed by structures or by stored material adjacent to the trench weigh in excess of the load imposed by a two-foot soil surcharge. The term “adjacent” as used here means the area...

29 CFR Appendix C to Subpart P of... - Timber Shoring for Trenches

Code of Federal Regulations, 2014 CFR

2014-07-01

.... Stable rock is exempt from shoring requirements and therefore, no data are presented for this condition... § 1926.652. (A) When loads imposed by structures or by stored material adjacent to the trench weigh in excess of the load imposed by a two-foot soil surcharge. The term “adjacent” as used here means the area...

A Ten-Meter Ground-Station Telescope for Deep-Space Optical Communications: A Preliminary Design

NASA Technical Reports Server (NTRS)

Britcliffe, M.; Hoppe, D.; Roberts, W.; Page, N.

2001-01-01

This article describes a telescope design for a 10-m optical ground station for deep-space communications. The design for a direct-detection optical communications telescope differs dramatically from a telescope for imaging applications. In general, the requirements for optical manufacturing and tracking performance are much less stringent for direct detection of optical signals. The technical challenge is providing a design that will operate in the daytime/nighttime conditions required for a Deep Space Network tracking application. The design presented addresses these requirements. The design will provide higher performance at lower cost than existing designs.

Microwave vs optical crosslink study

NASA Technical Reports Server (NTRS)

Kwong, Paulman W.; Bruno, Ronald C.; Marshalek, Robert G.

1992-01-01

The intersatellite links (ISL's) at geostationary orbit is currently a missing link in commercial satellite services. Prior studies have found that potential application of ISL's to domestic, regional, and global satellites will provide more cost-effective services than the non-ISL's systems (i.e., multiple-hop systems). In addition, ISL's can improve and expand the existing satellite services in several aspects. For example, ISL's can conserve the scarce spectrum allocated for fixed satellite services (FSS) by avoiding multiple hopping of the relay stations. ISL's can also conserve prime orbit slot by effectively expanding the geostationary arc. As a result of the coverage extension by using ISL's more users will have direct access to the satellite network, thus providing reduced signal propagation delay and improved signal quality. Given the potential benefits of ISL's system, it is of interest to determine the appropriate implementations for some potential ISL architectures. Summary of the selected ISL network architecture as supplied by NASA are listed. The projected high data rate requirements (greater than 400 Mbps) suggest that high frequency RF or optical implementations are natural approaches. Both RF and optical systems have their own merits and weaknesses which make the choice between them dependent on the specific application. Due to its relatively mature technology base, the implementation risk associated with RF (at least 32 GHz) is lower than that of the optical ISL's. However, the relatively large antenna size required by RF ISL's payload may cause real-estate problems on the host spacecraft. In addition, because of the frequency sharing (for duplex multiple channels communications) within the limited bandwidth allocated, RF ISL's are more susceptible to inter-system and inter-channel interferences. On the other hand, optical ISL's can offer interference-free transmission and compact sized payload. However, the extremely narrow beam widths (on the order of 10 micro-rad) associated with optical ISL's impose very stringent pointing, acquisition, and tracking requirements on the system. Even if the RF and optical systems are considered separately, questions still remain as to selection of RF frequency, direct versus coherent optical detection, etc. in implementing an ISL for a particular network architecture. These and other issues are studied.

Orphan Toxin OrtT (YdcX) of Escherichia coli Reduces Growth during the Stringent Response

DTIC Science & Technology

2015-01-29

antimicrobials trimethoprim and sulfamethoxazole; these antimicrobials induce the stringent response by inhibiting tetrahydrofolate synthesis...in the presence of both antimicrobials trimethoprim and sulfamethoxazole; these antimicrobials induce the stringent response by inhibiting...level [20]. Toxins 2015, 7 301 Despite these difficulties in determining physiological roles, TA systems are clearly phage inhibition systems

40 CFR 161.150 - General.

Code of Federal Regulations, 2010 CFR

2010-07-01

... expressed in the statement of formula. These data include information on the starting materials, production... product. (ii) Product composition data are compared to the composition of materials used in required... restrictions, labeling requirements, or special packaging requirements may be imposed. (iii) Product...

14 CFR 1260.130 - Purpose of property standards.

Code of Federal Regulations, 2012 CFR

2012-01-01

... project supported by a Federal award. Recipients shall observe these standards under awards and NASA will not impose additional requirements, unless specifically required by Federal statute. The recipient may...

14 CFR 1260.130 - Purpose of property standards.

Code of Federal Regulations, 2013 CFR

2013-01-01

... project supported by a Federal award. Recipients shall observe these standards under awards and NASA will not impose additional requirements, unless specifically required by Federal statute. The recipient may...

14 CFR 1260.130 - Purpose of property standards.

Code of Federal Regulations, 2010 CFR

2010-01-01

... project supported by a Federal award. Recipients shall observe these standards under awards and NASA will not impose additional requirements, unless specifically required by Federal statute. The recipient may...

14 CFR 1260.130 - Purpose of property standards.

Code of Federal Regulations, 2011 CFR

2011-01-01

... project supported by a Federal award. Recipients shall observe these standards under awards and NASA will not impose additional requirements, unless specifically required by Federal statute. The recipient may...

Process for fabrication of large titanium diboride ceramic bodies

DOEpatents

Moorhead, Arthur J.; Bomar, E. S.; Becher, Paul F.

1989-01-01

A process for manufacturing large, fully dense, high purity TiB.sub.2 articles by pressing powders with a sintering aid at relatively low temperatures to reduce grain growth. The process requires stringent temperature and pressure applications in the hot-pressing step to ensure maximum removal of sintering aid and to avoid damage to the fabricated article or the die.

A polyketide synthase gene and an aspartate kinase like gene are required for the biosynthesis of fusaric acid in Fusarium Oxysporum f. sp. Vasinfectum

USDA-ARS?s Scientific Manuscript database

A genetically unique strain of the Fusarium wilt pathogen was first recognized in wilted and dead Upland cotton seedlings in Australia in 1993. Since that time the disease spread rapidly despite stringent containment practices. The Australian biotype isolates of Fusarium oxysporum f. sp. vasinfec...

Rugged, Tunable Extended-Cavity Diode Laser

NASA Technical Reports Server (NTRS)

Moore, Donald; Brinza, David; Seidel, David; Klipstein, William; Choi, Dong Ho; Le, Lam; Zhang, Guangzhi; Iniguez, Roberto; Tang, Wade

2007-01-01

A rugged, tunable extended-cavity diode laser (ECDL) has been developed to satisfy stringent requirements for frequency stability, notably including low sensitivity to vibration. This laser is designed specifically for use in an atomic-clock experiment to be performed aboard the International Space Station (ISS). Lasers of similar design would be suitable for use in terrestrial laboratories engaged in atomic-clock and atomic-physics research.

The Limits of Civic Education: The Divergent Implications of Political and Comprehensive Liberalism

ERIC Educational Resources Information Center

Fowler, Tim

2011-01-01

Education has become one of the foremost arenas in which political liberals attempt to differentiate their account from that of comprehensive liberals. Rawls posits that the requirements of his theory, as laid out in "Political Liberalism," will be far less stringent than those of liberals such as Kant, Mill or Joseph Raz. However, a number of…

The Human Rights Context for Ethical Requirements for Involving People with Intellectual Disability in Medical Research

ERIC Educational Resources Information Center

Iacono, T.; Carling-Jenkins, R.

2012-01-01

Background: The history of ethical guidelines addresses protection of human rights in the face of violations. Examples of such violations in research involving people with intellectual disabilities (ID) abound. We explore this history in an effort to understand the apparently stringent criteria for the inclusion of people with ID in research, and…

A Study of Covert Communications in Space Platforms Hosting Government Payloads

DTIC Science & Technology

2015-02-01

possible adversarial actions (e.g., malicious software co- resident on the commercial host). Threats to the commercial supply chain are just one... supply chain to either create or exploit channel vulnerabilities. For government hosted payload missions, the critical payload data are encrypted...access to space by hosting government- supplied payloads on commercial space platforms. These commercially hosted payloads require stringent

Attitude control of an orbiting space vehicle.

NASA Technical Reports Server (NTRS)

Sutherlin, D. W.; Boland, J. S. , III; Borelli, M. T.

1971-01-01

Study of the normal and clamped modes of operation and dynamic response characteristics of the gimbaled control moment gyro (CMG) designed to fulfill the stringent pointing requirements of the Skylab telescope mount when the spacecraft is under the influence of both external and internal torques. The results indicate that the clamped mode of operation provides a feasible approach for significantly improving the system characteristics.

Evaluating the fate of mercury and other metals across the life-cycle stages from the use of FGD gypsum for wallboard production

EPA Science Inventory

In 2007, 12.3 million tons of flue gas desulfurization (FGD) gypsum was produced due to air emission controls at coal-fired power plants. With increasing use of wet scrubbers in response to more stringent air pollution control requirements, FGD gypsum production is expected to in...

75 FR 81765 - Safety Standards for Full-Size Baby Cribs and Non-Full-Size Baby Cribs; Final Rule

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-28

...Section 104(b) of the Consumer Product Safety Improvement Act of 2008 (``CPSIA'') requires the United States Consumer Product Safety Commission (``CPSC,'' ``Commission,'' or ``we'') to promulgate consumer product safety standards for durable infant or toddler products. These standards are to be ``substantially the same as'' applicable voluntary standards or more stringent than the voluntary standard if the Commission concludes that more stringent requirements would further reduce the risk of injury associated with the product. The Commission is issuing safety standards for full-size and non-full-size baby cribs in response to the direction under section 104(b) of the CPSIA.\\1\\ Section 104(c) of the CPSIA specifies that the crib standards will cover used as well as new cribs. The crib standards will apply to anyone who manufactures, distributes, or contracts to sell a crib; to child care facilities, family child care homes, and others holding themselves out to be knowledgeable about cribs; to anyone who leases, sublets, or otherwise places a crib in the stream of commerce; and to owners and operators of places of public accommodation affecting commerce. ---------------------------------------------------------------------------

Power Enhancement in High Dimensional Cross-Sectional Tests

PubMed Central

Fan, Jianqing; Liao, Yuan; Yao, Jiawei

2016-01-01

We propose a novel technique to boost the power of testing a high-dimensional vector H : θ = 0 against sparse alternatives where the null hypothesis is violated only by a couple of components. Existing tests based on quadratic forms such as the Wald statistic often suffer from low powers due to the accumulation of errors in estimating high-dimensional parameters. More powerful tests for sparse alternatives such as thresholding and extreme-value tests, on the other hand, require either stringent conditions or bootstrap to derive the null distribution and often suffer from size distortions due to the slow convergence. Based on a screening technique, we introduce a “power enhancement component”, which is zero under the null hypothesis with high probability, but diverges quickly under sparse alternatives. The proposed test statistic combines the power enhancement component with an asymptotically pivotal statistic, and strengthens the power under sparse alternatives. The null distribution does not require stringent regularity conditions, and is completely determined by that of the pivotal statistic. As specific applications, the proposed methods are applied to testing the factor pricing models and validating the cross-sectional independence in panel data models. PMID:26778846

14 CFR § 1260.130 - Purpose of property standards.

Code of Federal Regulations, 2014 CFR

2014-01-01

... project supported by a Federal award. Recipients shall observe these standards under awards and NASA will not impose additional requirements, unless specifically required by Federal statute. The recipient may...

34 CFR 74.30 - Purpose of property standards.

Code of Federal Regulations, 2013 CFR

2013-07-01

... project supported by a Federal award. Recipients shall observe these standards under awards. The Secretary does not impose additional requirements, unless specifically required by Federal statute. The recipient... INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, AND OTHER NON-PROFIT ORGANIZATIONS Post-Award Requirements...

34 CFR 74.30 - Purpose of property standards.

Code of Federal Regulations, 2014 CFR

2014-07-01

... project supported by a Federal award. Recipients shall observe these standards under awards. The Secretary does not impose additional requirements, unless specifically required by Federal statute. The recipient... INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, AND OTHER NON-PROFIT ORGANIZATIONS Post-Award Requirements...

34 CFR 74.30 - Purpose of property standards.

Code of Federal Regulations, 2011 CFR

2011-07-01

... project supported by a Federal award. Recipients shall observe these standards under awards. The Secretary does not impose additional requirements, unless specifically required by Federal statute. The recipient... INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, AND OTHER NON-PROFIT ORGANIZATIONS Post-Award Requirements...

34 CFR 74.30 - Purpose of property standards.

Code of Federal Regulations, 2012 CFR

2012-07-01

... project supported by a Federal award. Recipients shall observe these standards under awards. The Secretary does not impose additional requirements, unless specifically required by Federal statute. The recipient... INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, AND OTHER NON-PROFIT ORGANIZATIONS Post-Award Requirements...

34 CFR 74.30 - Purpose of property standards.

Code of Federal Regulations, 2010 CFR

2010-07-01

... project supported by a Federal award. Recipients shall observe these standards under awards. The Secretary does not impose additional requirements, unless specifically required by Federal statute. The recipient... INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, AND OTHER NON-PROFIT ORGANIZATIONS Post-Award Requirements...

10 CFR 55.7 - Additional requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 2 2014-01-01 2014-01-01 false Additional requirements. 55.7 Section 55.7 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) OPERATORS' LICENSES General Provisions § 55.7 Additional requirements. The Commission may, by rule, regulation, or order, impose upon any licensee such requirements, in addition to...

10 CFR 55.7 - Additional requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Additional requirements. 55.7 Section 55.7 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) OPERATORS' LICENSES General Provisions § 55.7 Additional requirements. The Commission may, by rule, regulation, or order, impose upon any licensee such requirements, in addition to...

42 CFR 457.555 - Maximum allowable cost-sharing charges on targeted low-income children in families with income...

Code of Federal Regulations, 2011 CFR

2011-10-01

... requirements must be met: (1)(i) For Federal FY 2009, any co-payment or similar charge the State imposes under a fee-for-service delivery system may not exceed the amounts shown in the following table: State...) For Federal FY 2009, any co-payment that the State imposes for services provided by a managed care...

42 CFR 457.555 - Maximum allowable cost-sharing charges on targeted low-income children in families with income...

Code of Federal Regulations, 2010 CFR

2010-10-01

... requirements must be met: (1)(i) For Federal FY 2009, any co-payment or similar charge the State imposes under a fee-for-service delivery system may not exceed the amounts shown in the following table: State...) For Federal FY 2009, any co-payment that the State imposes for services provided by a managed care...

42 CFR 137.406 - In compiling reports pursuant to this section, may the Secretary impose any reporting...

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 1 2014-10-01 2014-10-01 false In compiling reports pursuant to this section, may the Secretary impose any reporting requirements on Self-Governance Tribes, not otherwise provided in Title V? 137.406 Section 137.406 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES INDIAN HEALTH SERVICE, DEPARTMENT OF...

42 CFR 137.406 - In compiling reports pursuant to this section, may the Secretary impose any reporting...

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 1 2012-10-01 2012-10-01 false In compiling reports pursuant to this section, may the Secretary impose any reporting requirements on Self-Governance Tribes, not otherwise provided in Title V? 137.406 Section 137.406 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES INDIAN HEALTH SERVICE, DEPARTMENT OF...

42 CFR 137.406 - In compiling reports pursuant to this section, may the Secretary impose any reporting...

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false In compiling reports pursuant to this section, may the Secretary impose any reporting requirements on Self-Governance Tribes, not otherwise provided in Title V? 137.406 Section 137.406 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES INDIAN HEALTH SERVICE, DEPARTMENT OF...

10 CFR 434.101 - Scope.

Code of Federal Regulations, 2010 CFR

2010-01-01

... occupant comfort and sanitation, and which impose thermal loads in excess of 5% of the loads that would otherwise be required for occupant comfort and sanitation without the process; 101.2.4Envelope requirements...

The human rights context for ethical requirements for involving people with intellectual disability in medical research.

PubMed

Iacono, T; Carling-Jenkins, R

2012-11-01

The history of ethical guidelines addresses protection of human rights in the face of violations. Examples of such violations in research involving people with intellectual disabilities (ID) abound. We explore this history in an effort to understand the apparently stringent criteria for the inclusion of people with ID in research, and differences between medical and other research within a single jurisdiction. The history of the Helsinki Declaration and informed consent within medical research, and high-profile examples of ethical misconduct involving people with ID and other groups are reviewed. The UN Convention on the Rights of Persons with Disabilities is then examined for its research implications. This background is used to examine a current anomaly within an Australian context for the inclusion of people with ID without decisional capacity in medical versus other types of research. Ethical guidelines have often failed to protect the human rights of people with ID and other vulnerable groups. Contrasting requirements within an Australian jurisdiction for medical and other research would seem to have originated in early deference to medical authority for making decisions on behalf of patients. Stringent ethical requirements are likely to continue to challenge researchers in ID. A human rights perspective provides a framework for engaging both researchers and vulnerable participant groups. © 2012 The Authors. Journal of Intellectual Disability Research © 2012 Blackwell Publishing Ltd.

Manufacturability study of masks created by inverse lithography technology (ILT)

NASA Astrophysics Data System (ADS)

Martin, Patrick M.; Progler, C. J.; Xiao, G.; Gray, R.; Pang, L.; Liu, Y.

2005-11-01

As photolithography is pushed to fabricate deep-sub wavelength devices for 90nm, 65nm and smaller technology nodes using available exposure tools (i.e., 248nm, 193nm steppers), photomask capability is becoming extremely critical. For example, PSM masks require more complicated processing; aggressive OPC makes the writing time longer and sometimes unpredictable; and, high MEEF imposes much more stringent demands on mask quality. Therefore, in order for any new lithography technology to be adopted into production, mask manufacturability must be studied thoroughly and carefully. In this paper we will present the mask manufacturability study on mask patterns created using Inverse Lithography Technology (ILT). Unlike conventional OPC methodologies, ILT uses a unique outcome-based technology to mathematically determine the mask features that produce the desired on-wafer results. ILT solves the most critical litho challenges of the deep sub-wavelength era. Potential benefits include: higher yield; expanded litho process windows; superb pattern fidelity at 90, 65 & 45-nm nodes; and reduced time-to-silicon - all without changing the existing lithography infrastructure and design-to-silicon flow. In this study a number of cell structures were selected and used as test patterns. "Luminized patterns" were generated for binary mask and attenuated phase-shift mask. Both conventional OPC patterns and "luminized patterns" were put on a test reticle side by side, and they all have a number of variations in term of correction aggressivity level and mask complexity. Mask manufacturability, including data fracturing, writing time, mask inspection, and metrology were studied. The results demonstrate that, by optimizing the inspection recipe, masks created using ILT technology can be made and qualified using current processes with a reasonable turn-around time.

MEMS-based flexible reflective analog modulators (FRAM) for projection displays: a technology review and scale-down study

NASA Astrophysics Data System (ADS)

Picard, Francis; Ilias, Samir; Asselin, Daniel; Boucher, Marc-André; Duchesne, François; Jacob, Michel; Larouche, Carl; Vachon, Carl; Niall, Keith K.; Jerominek, Hubert

2011-02-01

A MEMS based technology for projection display is reviewed. This technology relies on mechanically flexible and reflective microbridges made of aluminum alloy. A linear array of such micromirrors is combined with illumination and Schlieren optics to produce a pixels line. Each microbridge in the array is individually controlled using electrostatic actuation to adjust the pixels intensities. Results of the simulation, fabrication and characterization of these microdevices are presented. Activation voltages below 250 V with response times below 10 μs were obtained for 25 μm × 25 μm micromirrors. With appropriate actuation voltage waveforms, response times of 5 μs and less are achievable. A damage threshold of the mirrors above 8 kW/cm2 has been evaluated. Development of the technology has produced projector engines demonstrating this light modulation principle. The most recent of these engines is DVI compatible and displays VGA video streams at 60 Hz. Recently applications have emerged that impose more stringent requirements on the dimensions of the MEMS array and associated optical system. This triggered a scale down study to evaluate the minimum micromirror size achievable, the impact of this reduced size on the damage threshold and the achievable minimum size of the associated optical system. Preliminary results of this scale down study are reported. FRAM with active surface as small as 5 μm × 5 μm have been investigated. Simulations have shown that such micromirrors could be activated with 107 V to achieve f-number of 1.25. The damage threshold has been estimated for various FRAM sizes. Finally, design of a conceptual miniaturized projector based on 1000×1 array of 5 μm × 5 μm micromirrors is presented. The volume of this projector concept is about 12 cm3.

Design of active temperature compensated composite free-free beam MEMS resonators in a standard process

NASA Astrophysics Data System (ADS)

Xereas, George; Chodavarapu, Vamsy P.

2014-03-01

Frequency references are used in almost every modern electronic device including mobile phones, personal computers, and scientific and medical instrumentation. With modern consumer mobile devices imposing stringent requirements of low cost, low complexity, compact system integration and low power consumption, there has been significant interest to develop batch-manufactured MEMS resonators. An important challenge for MEMS resonators is to match the frequency and temperature stability of quartz resonators. We present 1MHz and 20MHz temperature compensated Free-Free beam MEMS resonators developed using PolyMUMPS, which is a commercial multi-user process available from MEMSCAP. We introduce a novel temperature compensation technique that enables high frequency stability over a wide temperature range. We used three strategies: passive compensation by using a structural gold (Au) layer on the resonator, active compensation through using a heater element, and a Free-Free beam design that minimizes the effects of thermal mismatch between the vibrating structure and the substrate. Detailed electro-mechanical simulations were performed to evaluate the frequency response and Quality Factor (Q). Specifically, for the 20MHz device, a Q of 10,000 was obtained for the passive compensated design. Finite Element Modeling (FEM) simulations were used to evaluate the Temperature Coefficient of frequency (TCf) of the resonators between -50°C and 125°C which yielded +0.638 ppm/°C for the active compensated, compared to -1.66 ppm/°C for the passively compensated design and -8.48 ppm/°C for uncompensated design for the 20MHz device. Electro-thermo-mechanical simulations showed that the heater element was capable of increasing the temperature of the resonators by approximately 53°C with an applied voltage of 10V and power consumption of 8.42 mW.

7 CFR 3560.452 - Monetary and non-monetary defaults.

Code of Federal Regulations, 2011 CFR

2011-01-01

... requirements, including requirements imposed on a borrower through a workout agreement developed in accordance... agreement, workout agreement, or other agreement remains due more than 30 days after the due date. (c...

7 CFR 3560.452 - Monetary and non-monetary defaults.

Code of Federal Regulations, 2010 CFR

2010-01-01

... requirements, including requirements imposed on a borrower through a workout agreement developed in accordance... agreement, workout agreement, or other agreement remains due more than 30 days after the due date. (c...

42 CFR 436.520 - Age requirements for the aged.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 4 2013-10-01 2013-10-01 false Age requirements for the aged. 436.520 Section 436... Requirements for Medicaid Eligibility Age § 436.520 Age requirements for the aged. The agency must not impose an age requirement of more than 65 years. [58 FR 4936, Jan. 19, 1993] ...

42 CFR 436.520 - Age requirements for the aged.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 4 2012-10-01 2012-10-01 false Age requirements for the aged. 436.520 Section 436... Requirements for Medicaid Eligibility Age § 436.520 Age requirements for the aged. The agency must not impose an age requirement of more than 65 years. [58 FR 4936, Jan. 19, 1993] ...

42 CFR 436.520 - Age requirements for the aged.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 4 2014-10-01 2014-10-01 false Age requirements for the aged. 436.520 Section 436... Requirements for Medicaid Eligibility Age § 436.520 Age requirements for the aged. The agency must not impose an age requirement of more than 65 years. [58 FR 4936, Jan. 19, 1993] ...

42 CFR 436.520 - Age requirements for the aged.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 4 2011-10-01 2011-10-01 false Age requirements for the aged. 436.520 Section 436... Requirements for Medicaid Eligibility Age § 436.520 Age requirements for the aged. The agency must not impose an age requirement of more than 65 years. [58 FR 4936, Jan. 19, 1993] ...

42 CFR 436.520 - Age requirements for the aged.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 4 2010-10-01 2010-10-01 false Age requirements for the aged. 436.520 Section 436... Requirements for Medicaid Eligibility Age § 436.520 Age requirements for the aged. The agency must not impose an age requirement of more than 65 years. [58 FR 4936, Jan. 19, 1993] ...

77 FR 8148 - Anti-Money Laundering Program and Suspicious Activity Report Filing Requirements for Residential...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-14

... 1506-AB02 Anti-Money Laundering Program and Suspicious Activity Report Filing Requirements for... finance companies for the purpose of requiring them to establish anti-money laundering programs and report... Secretary is authorized to impose anti-money laundering (``AML'') program requirements on financial...

15 CFR 738.3 - Commerce Country Chart structure.

Code of Federal Regulations, 2010 CFR

2010-01-01

... license requirements for most items listed on the CCL. Such license requirements are based on the Reasons... ECCNs, however, impose license requirements either without reference to a reason for control code that... their license requirements in full in their “Reasons for Control” sections or they may refer the reader...

10 CFR 600.130 - Purpose of property standards.

Code of Federal Regulations, 2013 CFR

2013-01-01

... award. Recipients shall observe these standards under awards and shall not impose additional requirements, unless specifically required by Federal statute or program regulations. The recipient may use its..., Hospitals, and Other Nonprofit Organizations Post-Award Requirements § 600.130 Purpose of property standards...

20 CFR 435.30 - Purpose of property standards.

Code of Federal Regulations, 2014 CFR

2014-04-01

... Federal award. Recipients must observe these standards under awards and SSA may not impose additional requirements, unless specifically required by Federal statute. The recipient may use its own property..., AND COMMERCIAL ORGANIZATIONS Post-Award Requirements Property Standards § 435.30 Purpose of property...

10 CFR 600.130 - Purpose of property standards.

Code of Federal Regulations, 2010 CFR

2010-01-01

... award. Recipients shall observe these standards under awards and shall not impose additional requirements, unless specifically required by Federal statute or program regulations. The recipient may use its..., Hospitals, and Other Nonprofit Organizations Post-Award Requirements § 600.130 Purpose of property standards...

10 CFR 600.130 - Purpose of property standards.

Code of Federal Regulations, 2011 CFR

2011-01-01

... award. Recipients shall observe these standards under awards and shall not impose additional requirements, unless specifically required by Federal statute or program regulations. The recipient may use its..., Hospitals, and Other Nonprofit Organizations Post-Award Requirements § 600.130 Purpose of property standards...

10 CFR 600.130 - Purpose of property standards.

Code of Federal Regulations, 2014 CFR

2014-01-01

... award. Recipients shall observe these standards under awards and shall not impose additional requirements, unless specifically required by Federal statute or program regulations. The recipient may use its..., Hospitals, and Other Nonprofit Organizations Post-Award Requirements § 600.130 Purpose of property standards...

20 CFR 435.30 - Purpose of property standards.

Code of Federal Regulations, 2012 CFR

2012-04-01

... Federal award. Recipients must observe these standards under awards and SSA may not impose additional requirements, unless specifically required by Federal statute. The recipient may use its own property..., AND COMMERCIAL ORGANIZATIONS Post-Award Requirements Property Standards § 435.30 Purpose of property...

20 CFR 435.30 - Purpose of property standards.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Federal award. Recipients must observe these standards under awards and SSA may not impose additional requirements, unless specifically required by Federal statute. The recipient may use its own property..., AND COMMERCIAL ORGANIZATIONS Post-Award Requirements Property Standards § 435.30 Purpose of property...

10 CFR 600.130 - Purpose of property standards.

Code of Federal Regulations, 2012 CFR

2012-01-01

... award. Recipients shall observe these standards under awards and shall not impose additional requirements, unless specifically required by Federal statute or program regulations. The recipient may use its..., Hospitals, and Other Nonprofit Organizations Post-Award Requirements § 600.130 Purpose of property standards...

20 CFR 435.30 - Purpose of property standards.

Code of Federal Regulations, 2013 CFR

2013-04-01

... Federal award. Recipients must observe these standards under awards and SSA may not impose additional requirements, unless specifically required by Federal statute. The recipient may use its own property..., AND COMMERCIAL ORGANIZATIONS Post-Award Requirements Property Standards § 435.30 Purpose of property...

42 CFR 423.168 - Accreditation organizations.

Code of Federal Regulations, 2014 CFR

2014-10-01

... any proposed changes in its accreditation standards or requirements or survey process. If the... application and enforcement of those standards to the comparable CMS requirements and processes when— (i) CMS imposes new requirements or changes its survey process; (ii) An accreditation organization proposes to...

42 CFR 423.168 - Accreditation organizations.

Code of Federal Regulations, 2013 CFR

2013-10-01

... any proposed changes in its accreditation standards or requirements or survey process. If the... application and enforcement of those standards to the comparable CMS requirements and processes when— (i) CMS imposes new requirements or changes its survey process; (ii) An accreditation organization proposes to...

42 CFR 423.168 - Accreditation organizations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... any proposed changes in its accreditation standards or requirements or survey process. If the... application and enforcement of those standards to the comparable CMS requirements and processes when— (i) CMS imposes new requirements or changes its survey process; (ii) An accreditation organization proposes to...

42 CFR 423.168 - Accreditation organizations.

Code of Federal Regulations, 2012 CFR

2012-10-01

... any proposed changes in its accreditation standards or requirements or survey process. If the... application and enforcement of those standards to the comparable CMS requirements and processes when— (i) CMS imposes new requirements or changes its survey process; (ii) An accreditation organization proposes to...

An Ada implementation of the network manager for the advanced information processing system

NASA Technical Reports Server (NTRS)

Nagle, Gail A.

1986-01-01

From an implementation standpoint, the Ada language provided many features which facilitated the data and procedure abstraction process. The language supported a design which was dynamically flexible (despite strong typing), modular, and self-documenting. Adequate training of programmers requires access to an efficient compiler which supports full Ada. When the performance issues for real time processing are finally addressed by more stringent requirements for tasking features and the development of efficient run-time environments for embedded systems, the full power of the language will be realized.

Proceedings: Workshop on Environmental Considerations in the Life-Cycle of Paints and Coatings Held in Champaign, Illinois on September 9-10, 1986

DTIC Science & Technology

1988-07-01

MSDS or Material Safety Data Sheets from our suppliers and we are required to provide the same for our customers . We are required to train our personnel...non-sparking tools. Labels We protect our customers by labeling our materials in accordance with the NPCA Labeling Guide which is at least as...stringent as any federal or local regulations, by providing Material Safety Data Sheets and by providing customer assistance O when requested regarding safe

Reliability issues of free-space communications systems and networks

NASA Astrophysics Data System (ADS)

Willebrand, Heinz A.

2003-04-01

Free space optics (FSO) is a high-speed point-to-point connectivity solution traditionally used in the enterprise campus networking market for building-to-building LAN connectivity. However, more recently some wire line and wireless carriers started to deploy FSO systems in their networks. The requirements on FSO system reliability, meaing both system availability and component reliability, are far more stringent in the carrier market when compared to the requirements in the enterprise market segment. This paper tries to outline some of the aspects that are important to ensure carrier class system reliability.

On-orbit damage detection and health monitoring of large space trusses: Status and critical issues

NASA Technical Reports Server (NTRS)

Kashangaki, Thomas A. L.

1991-01-01

The long lifetimes, delicate nature and stringent pointing requirements of large space structures such as Space Station Freedom and geostationary Earth sciences platforms might require that these spacecraft be monitored periodically for possible damage to the load carrying structures. A review of the literature in damage detection and health monitoring of such structures is presented, along with a candidate structure to be used as a testbed for future work in this field. A unified notation and terminology is also proposed to facilitate comparisons between candidate methods.

Considering the Role of Natural Gas in the Deep Decarbonization of the U.S. Electricity Sector. Natural Gas and the Evolving U.S. Power Sector Monograph Series: Number 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cole, Wesley; Beppler, Ross; Zinaman, Owen

Natural gas generation in the U.S. electricity sector has grown substantially in recent years, while the sector's carbon dioxide (CO2) emissions have generally declined. This relationship highlights the concept of natural gas as a potential enabler of a transition to a lower-carbon future. This work considers that concept by using the National Renewable Energy Laboratory (NREL) Renewable Energy Deployment System (ReEDS) model. ReEDS is a long-term capacity expansion model of the U.S. electricity sector. We examine the role of natural gas within the ReEDS modeling framework as increasingly strict carbon emission targets are imposed on the electricity sector. In additionmore » to various natural gas price futures, we also consider scenarios that emphasize a low-carbon technology in order to better understand the role of natural gas if that low-carbon technology shows particular promise. Specifically, we consider scenarios with high amounts of energy efficiency (EE), low nuclear power costs, low renewable energy (RE) costs, and low carbon capture and storage (CCS) costs. Within these scenarios we find that requiring the electricity sector to lower CO2 emissions over time increases near-to-mid-term (through 2030) natural gas generation (see Figure 1 - left). The long-term (2050) role of natural gas generation in the electricity sector is dependent on the level of CO2 emission reduction required. Moderate reductions in long-term CO2 emissions have relatively little impact on long-term natural gas generation, while more stringent CO2 emission limits lower long-term natural gas generation (see Figure 1 - right). More stringent carbon targets also impact other generating technologies, with the scenarios considered here seeing significant decreases in coal generation, and new capacity of nuclear and renewable energy technologies over time. Figure 1 also demonstrates the role of natural gas in the context of scenarios where a specific low-carbon technology is advantaged. In 2030, natural gas generation in the technology scenarios is quite similar to that in the reference scenarios, indicating relatively little change in the role of natural gas in the near-to-mid-term due to advancements in those technology areas. The 2050 natural gas generation shows more significant differences, suggesting that technology advancements will likely have substantial impacts on the role of natural gas in the longer-term timeframe. Natural gas generation differences are most strongly driven by alternative natural gas price trajectories--changes in natural gas generation in the Low NG Price and High NG Price scenarios are much larger than in any other scenario in both the 2030 and 2050 timeframes. The only low-carbon technology scenarios that showed any increase in long-term natural gas generation relative to the reference case were the Low CCS cost scenarios. Carbon capture and storage technology costs are currently high, but have the potential to allow fossil fuels to play a larger role in low-carbon grid. This work considers three CCS cost trajectories for natural gas and coal generators: a baseline trajectory and two lower cost trajectories where CO2 capture costs reach $40/metric ton and $10/metric ton, respectively. We find that in the context of the ReEDS model and with these assumed cost trajectories, CCS can increase the long-term natural gas generation under a low carbon target (see Figure 2). Under less stringent carbon targets we do not see ReEDS electing to use CCS as part of its electricity generating portfolio for the scenarios considered in this work.« less

Cluster: A fleet of four spacecraft to study plasma structures in three dimensions

NASA Technical Reports Server (NTRS)

Schmidt, R.; Goldstein, M. L.

1988-01-01

The four Cluster spacecraft are spin stabilized spacecraft which are designed and built under stringent requirements as far as electromagnetic cleanliness is concerned. Conductive surfaces and low electromagnetic background noise are mandatory for accurate electric field and cold plasma measurements. The mission is implemented in collaboration between ESA and NASA. A Russian mission will be closely coordinated with Cluster.

Downsizing Antenna Technologies for Mobile and Satellite Communications

NASA Technical Reports Server (NTRS)

Huang, J.; Densmore, A.; Tulintseff, A.; Jamnejad, V.

1993-01-01

Due to the increasing and stringent functional requirements (larger capacity, longer distances, etc.) of modern day communication systems, higher antenna gains are generally needed. This higher gain implies larger antenna size and mass which are undesirable to many systems. Consequently, downsizing antenna technology becomes one of the most critical areas for research and development efforts. Techniques to reduce antenna size can be categorized and are briefly discussed.

Lightweight Solar Photovoltaic Blankets

NASA Technical Reports Server (NTRS)

Ceragioli, R.; Himmler, R.; Nath, P.; Vogeli, C.; Guha, S.

1995-01-01

Lightweight, flexible sheets containing arrays of stacked solar photovoltaic cells developed to supply electric power aboard spacecraft. Solar batteries satisfying stringent requirements for operation in outer space also adaptable to terrestrial environment. Attractive for use as long-lived, portable photovoltaic power sources. Cells based on amorphous silicon which offers potential for order-of-magnitude increases in power per unit weight, power per unit volume, and endurance in presence of ionizing radiation.

DOE Zero Energy Ready Home Case Study: Palo Duro Homes — Palo Duro Homes, Albuquerque, NM

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2014-09-01

This builder was honored for Most DOE Zero Energy Ready Homes Built in the 2014 Housing Innovation Awards. By July 2014, Palo Duro had completed 152 homes since the program began in 2013 (under the original program title DOE Challenge Home), all of them certified to the stringent efficiency requirements of DOE’s Zero Energy Ready Home program.

Low Impact Development for Industrial Areas

DTIC Science & Technology

2015-07-01

Stormwater program managers are faced with increasingly stringent stormwater discharge limits for heavy metals such as copper, zinc , nutrients, total...limits for heavy metals such as copper, zinc , nutrients, total suspended solids (TSS), oil and grease. These limits are required to reduce...U.S. EPA), state agencies, and local agencies set permit limits as part of the total mass daily loading regulatory framework. Copper, zinc , lead

32 CFR 700.106 - Control of administrative requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements will not be imposed unless the expected value of the information to be gained is significantly... within the chain of command or the issuing authority, the first common superior of the commands affected...

22 CFR 1203.735-410 - Effect of employees' statements on other requirements.

Code of Federal Regulations, 2012 CFR

2012-04-01

... substitution for, or in derogation of, any similar requirement imposed by law, order, or regulation. The... by law, order, or regulation. Save with respect to those financial interests excepted from the...

22 CFR 1203.735-410 - Effect of employees' statements on other requirements.

Code of Federal Regulations, 2014 CFR

2014-04-01

... substitution for, or in derogation of, any similar requirement imposed by law, order, or regulation. The... by law, order, or regulation. Save with respect to those financial interests excepted from the...

22 CFR 1203.735-410 - Effect of employees' statements on other requirements.

Code of Federal Regulations, 2013 CFR

2013-04-01

... substitution for, or in derogation of, any similar requirement imposed by law, order, or regulation. The... by law, order, or regulation. Save with respect to those financial interests excepted from the...

Thermal analysis and optimization of the EAST ICRH antenna

NASA Astrophysics Data System (ADS)

Qingxi, YANG; Wei, SONG; Qunshan, DU; Yuntao, SONG; Chengming, QIN; Xinjun, ZHANG; Yanping, ZHAO

2018-02-01

The ion cyclotron resonance of frequency heating (ICRH) plays an important role in plasma heating. Two ICRH antennas were designed and applied on the EAST tokamak. In order to meet the requirement imposed by high-power and long-pulse operation of EAST in the future, an active cooling system is mandatory to be designed to remove the heat load deposited on the components. Thermal analyses for high heat-load components have been carried out, which presented clear temperature distribution on each component and provided the reference data to do the optimization. Meanwhile, heat pipes were designed to satisfy the high requirement imposed by a Faraday shield and lateral limiter.

V and V of ISHM Software for Space Exploration

NASA Technical Reports Server (NTRS)

Markosian, Lawrence; Feather, Martin, S.; Brinza, David; Figueroa, F.

2005-01-01

NASA has established a far-reaching and long-term program for robotic and manned exploration of the solar system, beginning with missions to the moon and Mars. The Crew Transportation System (CTS), a key system for space exploration, imposes four requirements' that ISHM addresses. These requirements have a wide range of implications for V&V and certification of ISHM. There is a range of time-criticality for ISHM actions, from prognostication, which is often (but not always) non-time-critical, to time-critical state estimation and system management under off-nominal emergency conditions. These are externally imposed requirements on ISHM that are subject to V&V. - In addition, a range of techniques are needed to implement an ISHM. The approaches to ISHM are described elsewhere. These approaches range from well-understood algorithms for low-level data analysis, validation and reporting, to AI techniques for state estimation and planning. The range of techniques, and specifically the use of AI techniques such as reasoning under uncertainty and mission planning (and re-planning), implies that several V&V approaches may be required. Depending on the ISHM architecture, traditional testing approaches may be adequate for some ISHM functionality. The AI-based approaches to reasoning under uncertainty, model-based reasoning, and planning share characteristics typical of other complex software systems, but they also have characteristics that set them apart and challenge standard V&V techniques. The range of possible solutions to the overall ISHM problem impose internal challenges to V&V. The V&V challenges increase when hard real-time constraints are imposed for time-critical functionality. For example, there is an external requirement that impending catastrophic failure of the Launch Vehicle (LV) at launch time be detected and life-saving action be taken within two seconds. In this paper we outline the challenges for ISHM V&V, existing approaches and analogs in other software application areas, and possible new approaches to the V&V challenges for space exploration ISHM.

Intelligent redundant actuation system requirements and preliminary system design

NASA Technical Reports Server (NTRS)

Defeo, P.; Geiger, L. J.; Harris, J.

1985-01-01

Several redundant actuation system configurations were designed and demonstrated to satisfy the stringent operational requirements of advanced flight control systems. However, this has been accomplished largely through brute force hardware redundancy, resulting in significantly increased computational requirements on the flight control computers which perform the failure analysis and reconfiguration management. Modern technology now provides powerful, low-cost microprocessors which are effective in performing failure isolation and configuration management at the local actuator level. One such concept, called an Intelligent Redundant Actuation System (IRAS), significantly reduces the flight control computer requirements and performs the local tasks more comprehensively than previously feasible. The requirements and preliminary design of an experimental laboratory system capable of demonstrating the concept and sufficiently flexible to explore a variety of configurations are discussed.

10 CFR 835.601 - General requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... DEPARTMENT OF ENERGY OCCUPATIONAL RADIATION PROTECTION Posting and Labeling § 835.601 General requirements... include the standard radiation warning trefoil in black or magenta imposed upon a yellow background. (b... protection instructions. (c) The posting and labeling requirements in this subpart may be modified to reflect...

10 CFR 835.601 - General requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... DEPARTMENT OF ENERGY OCCUPATIONAL RADIATION PROTECTION Posting and Labeling § 835.601 General requirements... include the standard radiation warning trefoil in black or magenta imposed upon a yellow background. (b... protection instructions. (c) The posting and labeling requirements in this subpart may be modified to reflect...

10 CFR 835.601 - General requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... DEPARTMENT OF ENERGY OCCUPATIONAL RADIATION PROTECTION Posting and Labeling § 835.601 General requirements... include the standard radiation warning trefoil in black or magenta imposed upon a yellow background. (b... protection instructions. (c) The posting and labeling requirements in this subpart may be modified to reflect...

10 CFR 835.601 - General requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... DEPARTMENT OF ENERGY OCCUPATIONAL RADIATION PROTECTION Posting and Labeling § 835.601 General requirements... include the standard radiation warning trefoil in black or magenta imposed upon a yellow background. (b... protection instructions. (c) The posting and labeling requirements in this subpart may be modified to reflect...

10 CFR 835.601 - General requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... DEPARTMENT OF ENERGY OCCUPATIONAL RADIATION PROTECTION Posting and Labeling § 835.601 General requirements... include the standard radiation warning trefoil in black or magenta imposed upon a yellow background. (b... protection instructions. (c) The posting and labeling requirements in this subpart may be modified to reflect...

Registering medicines for low-income countries: how suitable are the stringent review procedures of the World Health Organisation, the US Food and Drug Administration and the European Medicines Agency?

PubMed

Doua, Joachim Y; Van Geertruyden, Jean-Pierre

2014-01-01

New medicines are registered after a resource-demanding process. Unfortunately, in low-income countries (LICs), demand outweighs resources. To facilitate registration in LICs, stringent review procedures of the European Medicines Agency (EMA Article-58), Food and Drug Administration (FDA PEPFAR-linked review) and WHO Prequalification programme have been established. Only the PEPFAR-linked review gives approval, while the others make recommendations for approval. This study assessed the performance and discussed the challenges of these three stringent review procedures. Data from WHO, FDA, EMA, Medline and Internet were analysed. Over 60% of medicines reviewed by stringent review procedures are manufactured in India. Until 2012, WHO prequalified 400 medicines (211 vaccines, 130 antiretrovirals, 29 tuberculostatics, 15 antimalarials and 15 others). PEPFAR-linked review approved 156 antiretrovirals, while EMA Article 58 recommended approval of 3 antiretrovirals, 1 vaccine and 1 antimalarial. WHO Prequalification and PEPFAR-linked review are free of charge and as a result have accelerated access to antiretrovirals. They both built capacity in sub-Saharan Africa, although WHO prequalification relies technically on stringent regulatory authorities and financially on donors. Article-58 offers the largest disease coverage and strongest technical capacities, is costly and involves fewer LICs. To meet the high demand for quality medicines in LICs, these stringent review procedures need to enlarge their disease coverage. To improve registration, EMA Article 58 should actively involve LICs. Furthermore, LIC regulatory activities must not be fully resigned to stringent review procedure. © 2013 John Wiley & Sons Ltd.

42 CFR 435.520 - Age requirements for the aged.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 4 2013-10-01 2013-10-01 false Age requirements for the aged. 435.520 Section 435... ISLANDS, AND AMERICAN SAMOA Categorical Requirements for Eligibility Age § 435.520 Age requirements for the aged. The agency must not impose an age requirement of more than 65 years. [58 FR 4929, Jan. 19...

42 CFR 435.520 - Age requirements for the aged.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 4 2011-10-01 2011-10-01 false Age requirements for the aged. 435.520 Section 435... ISLANDS, AND AMERICAN SAMOA Categorical Requirements for Eligibility Age § 435.520 Age requirements for the aged. The agency must not impose an age requirement of more than 65 years. [58 FR 4929, Jan. 19...

42 CFR 435.520 - Age requirements for the aged.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 4 2010-10-01 2010-10-01 false Age requirements for the aged. 435.520 Section 435... ISLANDS, AND AMERICAN SAMOA Categorical Requirements for Eligibility Age § 435.520 Age requirements for the aged. The agency must not impose an age requirement of more than 65 years. [58 FR 4929, Jan. 19...

42 CFR 435.520 - Age requirements for the aged.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 4 2012-10-01 2012-10-01 false Age requirements for the aged. 435.520 Section 435... ISLANDS, AND AMERICAN SAMOA Categorical Requirements for Eligibility Age § 435.520 Age requirements for the aged. The agency must not impose an age requirement of more than 65 years. [58 FR 4929, Jan. 19...

42 CFR 435.520 - Age requirements for the aged.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 4 2014-10-01 2014-10-01 false Age requirements for the aged. 435.520 Section 435... ISLANDS, AND AMERICAN SAMOA Categorical Requirements for Eligibility Age § 435.520 Age requirements for the aged. The agency must not impose an age requirement of more than 65 years. [58 FR 4929, Jan. 19...

Processing and Analysis of Mars Pathfinder Science Data at JPL's Science Data Processing Section

NASA Technical Reports Server (NTRS)

LaVoie, S.; Green, W.; Runkle, A.; Alexander, D.; Andres, P.; DeJong, E.; Duxbury, E.; Freda, D.; Gorjian, Z.; Hall, J.;

76 FR 8923 - Explosive Siting Requirements

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-16

....regulations.gov , including any personal information you provide. Using the search function of the docket Web... requirements, but do not impose explicit separation requirements. The employer must guarantee the mechanical... ensure these systems are adequate for their functions and must maintain the components. 29 CFR 1910.119(j...

29 CFR 36.125 - Effect of other requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Introduction § 36.125 Effect of other requirements. (a) Effect of other Federal provisions. The obligations imposed by these Title IX regulations are independent... Act of Congress or Federal regulation. (b) Effect of State or local law or other requirements. The...

10 CFR 1042.125 - Effect of other requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Introduction § 1042.125 Effect of other requirements. (a) Effect of other Federal provisions. The obligations imposed by these Title IX regulations are... Act of Congress or Federal regulation. (b) Effect of State or local law or other requirements. The...

42 CFR 422.157 - Accreditation organizations.

Code of Federal Regulations, 2014 CFR

2014-10-01

... requirements or survey process. If the organization implements the changes before or without CMS approval, CMS... requirements and processes when— (i) CMS imposes new requirements or changes its survey process; (ii) An accreditation organization proposes to adopt new standards or changes in its survey process; or (iii) The term...

42 CFR 422.157 - Accreditation organizations.

Code of Federal Regulations, 2012 CFR

2012-10-01

... requirements or survey process. If the organization implements the changes before or without CMS approval, CMS... requirements and processes when— (i) CMS imposes new requirements or changes its survey process; (ii) An accreditation organization proposes to adopt new standards or changes in its survey process; or (iii) The term...

42 CFR 422.157 - Accreditation organizations.

Code of Federal Regulations, 2013 CFR

2013-10-01

... requirements or survey process. If the organization implements the changes before or without CMS approval, CMS... requirements and processes when— (i) CMS imposes new requirements or changes its survey process; (ii) An accreditation organization proposes to adopt new standards or changes in its survey process; or (iii) The term...

Digital orthoimagery base specification V1.0

USGS Publications Warehouse

Rufe, Philip P.

2014-01-01

The resolution requirement for orthoimagery in support of the The National Map of the U.S. Geological Survey (USGS) is 1 meter. However, as the Office of Management and Budget A-16 designated Federal agency responsible for base orthoimagery, the USGS National Geospatial Program (NGP) has developed this base specification to include higher resolution orthoimagery. Many Federal, State, and local programs use high-resolution orthoimagery for various purposes including critical infrastructure management, vector data updates, land-use analysis, natural resource inventory, and extraction of data. The complex nature of large-area orthoimagery datasets, combined with the broad interest in orthoimagery, which is of consistent quality and spatial accuracy, requires high-resolution orthoimagery to meet or exceed the format and content outlined in this specification. The USGS intends to use this specification primarily to create consistency across all NGP funded and managed orthoimagery collections, in particular, collections in support of the National Digital Orthoimagery Program (NDOP). In the absence of other comprehensive specifications or standards, the USGS intends that this specification will, to the highest degree practical, be adopted by other USGS programs and mission areas, and by other Federal agencies. This base specification, defining minimum parameters for orthoimagery data collection. Local conditions in any given project area, specialized applications for the data, or the preferences of cooperators, may mandate more stringent requirements. The USGS fully supports the acquisition of more detailed, accurate, or value-added data that exceed the base specification outlined herein. A partial list of common “buy-up” options is provided in appendix 1 for those areas and projects that require more stringent or expanded specifications.

Advanced Space-Based Detector Research at the Air Force Research Laboratory

DTIC Science & Technology

2009-03-04

purposes. The dark backgrounds place very stringent requirements on the noise characteristics of the sensor system, resulting in FPAs that must be...signal within a single pixel of a detector. 2. Optical signal amplification 2.1. Quantum interference Quantum well infrared photodetectors ( QWIPs ) are...are now extremely attractive for a growing number of sensor applications. Although considerable progress has been made in QWIPs , their relatively low

Advanced Space-Based Detector Research at the Air Force Research Laboratory (PREPRINT)

DTIC Science & Technology

2006-10-01

purposes. The dark backgrounds place very stringent requirements on the noise characteristics of the sensor system, resulting in FPAs that must be cooled...2.1. Quantum interference Quantum well infrared photodetectors ( QWIPs ) are based on intersubband absorption in III–V semiconductor multi-quantum well...Although considerable progress has been made in QWIPs , their relatively low quantum efficiencies constitute their greatest problem for space-based

Vision Technology for Automated Inspection of Hybrid Microelectronics Assemblies

DTIC Science & Technology

1988-06-01

circuits are a very efficient packaging technique, with the primary advantages of size, better resistance to environ - 0 ments, and the flexibility to...produced for the military are much more complex and have more stringent performance requirements, particularly in their resistance to environments and...boards, particularly because of the need to protect circuits from a hostile environment such as salt, heat, and moisture. Included among the major U.S

Development of hermetic electrical connectors for SSC spool pieces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kountanis, B.; Kalny, L.

1993-05-01

The Superconducting Super Collider ring is about 54 miles (87 km circumference) and primarily includes a series of magnets. Spool piece assemblies are interspaced in the ring at predetermined intervals to provide specific functions such as cryogenic interfaces, vacuum interface, magnet power, magnet power dump, quench heater power, and special instrumentation. Electrical connectors serve as interfaces for instrumentation and quench heater circuits. These connectors have to meet stringent requirements.

Applications of Probabilistic Combiners on Linear Feedback Shift Register Sequences

DTIC Science & Technology

2016-12-01

on the resulting output strings show a drastic increase in complexity, while simultaneously passing the stringent randomness tests required by the...a three-variable function. Our tests on the resulting output strings show a drastic increase in complex- ity, while simultaneously passing the...10001101 01000010 11101001 Decryption of a message that has been encrypted using bitwise XOR is quite simple. Since each bit is its own additive inverse

The evolution and challenges for the international harmonization of the regulation of pharmaceutical excipients in Taiwan.

PubMed

Chang, Lin-Chau; Kang, Jaw-Jou; Gau, Churn-Shiouh

2015-12-01

Excipients, once considered an inert component, have been shown to greatly influence the characteristics of the drug product, such as quality and safety. Functionality-related characteristics of excipients could affect the performance of the drug product. Moreover, the impact of globalization has complicated the issue and made the supervision of supply chain highly important. Taiwan, a member of the Pharmaceutical Inspection Convention and Pharmaceutical Inspection Co-operation Scheme, makes efforts to harmonize with international regulations and to strengthen the protection of patients through regulatory controls. In order to improve the harmonization and the transparency of regulatory requirements, the aim of the present study was to investigate the regulatory framework and considerations of stringent regulatory authorities and to propose the draft regulatory requirements to the Taiwan Food and Drug Administration for jurisdiction. The proposal which was extensively discussed in the expert committee includes the regulatory considerations to ensure the safety and quality of the excipients and may serve as a platform to facilitate the communication with industries about the current thinking on related issues. Moreover, through the review of the recent guidelines published by the stringent regulatory authorities, the trend of the regulatory considerations was revealed and discussed. Copyright © 2015 Elsevier Inc. All rights reserved.

Model predictive control of a lean-burn gasoline engine coupled with a passive selective catalytic reduction system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Pingen; Lin, Qinghua; Prikhodko, Vitaly Y.

Lean-burn gasoline engines have demonstrated 10–20% engine efficiency gain over stoichiometric engines and are widely considered as a promising technology for meeting the 54.5 miles-per-gallon (mpg) Corporate Average Fuel Economy standard by 2025. Nevertheless, NOx emissions control for lean-burn gasoline for meeting the stringent EPA Tier 3 emission standards has been one of the main challenges towards the commercialization of highly-efficient lean-burn gasoline engines in the United States. Passive selective catalytic reduction (SCR) systems, which consist of a three-way catalyst and SCR, have demonstrated great potentials of effectively reducing NOx emissions for lean gasoline engines but may cause significant fuelmore » penalty due to ammonia generation via rich engine combustion. The purpose of this study is to develop a model-predictive control (MPC) scheme for a lean-burn gasoline engine coupled with a passive SCR system to minimize the fuel penalty associated with passive SCR operation while satisfying stringent NOx and NH3 emissions requirements. Simulation results demonstrate that the MPC-based control can reduce the fuel penalty by 47.7% in a simulated US06 cycle and 32.0% in a simulated UDDS cycle, compared to the baseline control, while achieving over 96% deNOx efficiency and less than 15 ppm tailpipe ammonia slip. The proposed MPC control can potentially enable high engine efficiency gain for highly-efficient lean-burn gasoline engine while meeting the stringent EPA Tier 3 emission standards.« less

24 CFR 266.120 - Actions for which sanctions may be imposed.

Code of Federal Regulations, 2010 CFR

2010-04-01

... affect HFA operations or financial status; (3) Comply with all eligibility requirements for participation...) Establish and maintain a dedicated account, if required, or meet other financial obligations under this... reference into the Risk-sharing Agreement; (8) Submit financial and other reports required by this part; (9...

40 CFR 92.1108 - In-use compliance provisions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... and locomotive engines subject to the requirements of this part: (1) If the Administrator determines... section. The manufacturer or remanufacturer shall comply in all respects with the requirements of subpart... dealer incurs as a result of a requirement imposed by paragraph (a) of this section. The transfer of any...

75 FR 63514 - Agency Information Collection Activities: Submission to OMB for Review; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-15

... be required to develop and submit a retained earnings accumulation plan. The rule generally requires... hours = 1,000 hours. Retained earnings accumulation Plans: 3 corporates x 50 hours = 150 hours. Notice... imposes new requirements concerning the use of nationally recognized statistical rating agencies, which...

31 CFR 370.23 - What other requirements apply to a financial institution?

Code of Federal Regulations, 2010 CFR

2010-07-01

... financial institution? 370.23 Section 370.23 Money and Finance: Treasury Regulations Relating to Money and... requirements apply to a financial institution? The financial institution warrants that it will comply with all requirements imposed upon Receiving Depository Financial Institutions under the Operating Rules of the National...

40 CFR 125.3 - Technology-based treatment requirements in permits.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 21 2010-07-01 2010-07-01 false Technology-based treatment... Criteria and Standards for Imposing Technology-Based Treatment Requirements Under Sections 301(b) and 402 of the Act § 125.3 Technology-based treatment requirements in permits. (a) General. Technology-based...

42 CFR 410.143 - Requirements for approved accreditation organizations.

Code of Federal Regulations, 2013 CFR

2013-10-01

...) Notice of any proposed changes in its accreditation standards and requirements or evaluation process. If... enforcement of its standards to a set of quality standards (described in § 410.144) and processes when any of the following conditions exist: (i) CMS imposes new requirements or changes its process for approving...

28 CFR 36.301 - Eligibility criteria.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., privileges, advantages, or accommodations being offered. (b) Safety. A public accommodation may impose legitimate safety requirements that are necessary for safe operation. Safety requirements must be based on... provision of auxiliary aids, barrier removal, alternatives to barrier removal, and reasonable modifications...

76 FR 23353 - Public Meeting: U.S. Registration of Aircraft in the Name of Owner Trustees

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-26

... resident alien, imposes additional requirements and limitations with respect to the power of such... above in need of amendment? 7. Which, if any, knowledge and information requirements (e.g., address of...

32 CFR 32.1 - Purpose.

Code of Federal Regulations, 2014 CFR

2014-07-01

... REQUIREMENTS FOR GRANTS AND AGREEMENTS WITH INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, AND OTHER NON-PROFIT... uniform administrative requirements for awards and subawards to institutions of higher education... of higher education, hospitals, and other non-profit organizations. DoD Components shall not impose...

32 CFR 32.1 - Purpose.

Code of Federal Regulations, 2011 CFR

2011-07-01

... REQUIREMENTS FOR GRANTS AND AGREEMENTS WITH INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, AND OTHER NON-PROFIT... uniform administrative requirements for awards and subawards to institutions of higher education... of higher education, hospitals, and other non-profit organizations. DoD Components shall not impose...

32 CFR 32.1 - Purpose.

Code of Federal Regulations, 2012 CFR

2012-07-01

... REQUIREMENTS FOR GRANTS AND AGREEMENTS WITH INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, AND OTHER NON-PROFIT... uniform administrative requirements for awards and subawards to institutions of higher education... of higher education, hospitals, and other non-profit organizations. DoD Components shall not impose...

32 CFR 32.1 - Purpose.

Code of Federal Regulations, 2013 CFR

2013-07-01

... REQUIREMENTS FOR GRANTS AND AGREEMENTS WITH INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, AND OTHER NON-PROFIT... uniform administrative requirements for awards and subawards to institutions of higher education... of higher education, hospitals, and other non-profit organizations. DoD Components shall not impose...

32 CFR 32.1 - Purpose.

Code of Federal Regulations, 2010 CFR

2010-07-01

... REQUIREMENTS FOR GRANTS AND AGREEMENTS WITH INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, AND OTHER NON-PROFIT... uniform administrative requirements for awards and subawards to institutions of higher education... of higher education, hospitals, and other non-profit organizations. DoD Components shall not impose...

Impacts of CERCLA Release Notification Requirements on Transportation of Products Containing Hazardous Substances

DOT National Transportation Integrated Search

1986-08-01

In order to determine the regulatory burden imposed by CERCLA release-notification requirements on shippers and carriers handling products containing hazardous substances, eight shippers and seven carriers were interviewed in depth during the summer ...

Gasoline Composition Regulations Affecting LUST Sites

EPA Science Inventory

Passage of the Clean Air Act Amendments in 1990 imposed requirements on gasoline composition in the United States. Impacts to ground water are affected by the provisions that required oxygenated additives and limited benzene concentration. Reformulated and oxygenated gasoline w...

Toward a workable biosafety system for regulating genetically modified organisms in Ethiopia: balancing conservation and competitiveness.

PubMed

Abraham, Adane

2013-01-01

On September 9, 2009, Ethiopia enacted a highly restrictive biosafety law firmly based on precautionary principles as a foundation for its GMO regulation system. Its drafting process, led by the country's Environmental Protection Authority, was judged as biased, focusing only on protecting the environment from perceived risks, giving little attention to potential benefits of GMOs. Many of its provisions are very stringent, exceeding those of Cartagena Protocol on Biosafety, while others cannot be fulfilled by applicants, collectively rendering the emerged biosafety system unworkable. These provisions include requirements for advance informed agreement and rigorous socioeconomic assessment in risk evaluation for all GMO transactions, including contained research use-which requires the head of the competent national authority of the exporting country to take full responsibility for GMO-related information provided-and stringent labeling, insurance and monitoring requirements for all GMO activities. Furthermore, there is no provision to establish an independent national biosafety decision-making body(ies). As a result, foreign technology owners that provide highly demanded technologies like Bt cotton declined to work with Ethiopia. There is a fear that the emerged biosafety system might also continue to suppress domestic genetic engineering research and development. Thus, to benefit from GMOs, Ethiopia has to revise its biosafety system, primarily by making changes to some provisions of the law in a way that balances its diverse interests of conserving biodiversity, protecting the environment and enhancing competition in agricultural and other economic sectors.

System issues and considerations associated with design of ground mobile strategic satellite communication terminals

NASA Astrophysics Data System (ADS)

Poliakon, J. A.

The current national defense doctrine calls for increased use of ground mobile strategic satellite communication earth terminals. This paper discusses some of the key communication terminal system issues and considerations associated with the design of nuclear hardened strategic ground mobile earth terminals. It considers system requirements such as nuclear hardness, rapid mobility, low profile, signal interference resistance, high availability, and long term independent operation. It also discusses impacts and implications associated with these requirements when imposed on a satellite earth terminal. It gives special focus to the ramifications of imposing mobility on earth terminals and its relationship to the system design approach used to arrive at an optimal system solution.

Dark Matter in B – L supersymmetric Standard Model with inverse seesaw

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abdallah, W.; Khalil, S., E-mail: awaleed@sci.cu.edu.eg, E-mail: s.khalil@zewailcity.edu.eg

We show that the B – L Supersymmetric Standard Model with Inverse Seesaw (BLSSMIS) provides new Dark Matter (DM) candidates (lightest right-handed sneutrino and lightest B – L neutralino) with mass of order few hundreds GeV, while most of other SUSY spectrum can be quite heavy, consistently with the current Large Hadron Collider (LHC) constraints. We emphasize that the thermal relic abundance and direct detection experiments via relic neutralino scattering with nuclei impose stringent constraints on the B – L neutralinos. These constraints can be satisfied by few points in the parameter space where the B – L lightest neutralinomore » is higgsino-like, which cannot explain the observed Galactic Center (GC) gamma-ray excess measured by Fermi-LAT. The lightest right-handed sneutrino DM is analysed. We show that for a wide region of parameter space the lightest right-handed sneutrino, with mass between 80 GeV and 1.2 TeV, can satisfy the limits of the relic abundance and the scattering cross section with nuclei. We also show that the lightest right-handed sneutrino with mass O(100) GeV can account for the observed GC gamma-ray results.« less

AIDing Chromatin and Transcription-Coupled Orchestration of Immunoglobulin Class-Switch Recombination

PubMed Central

Vaidyanathan, Bharat; Yen, Wei-Feng; Pucella, Joseph N.; Chaudhuri, Jayanta

2014-01-01

Secondary diversification of the antibody repertoire upon antigenic challenge, in the form of immunoglobulin heavy chain (IgH) class-switch recombination (CSR) endows mature, naïve B cells in peripheral lymphoid organs with a limitless ability to mount an optimal humoral immune response, thus expediting pathogen elimination. CSR replaces the default constant (CH) region exons (Cμ) of IgH with any of the downstream CH exons (Cγ, Cε, or Cα), thereby altering effector functions of the antibody molecule. This process depends on, and is orchestrated by, activation-induced deaminase (AID), a DNA cytidine deaminase that acts on single-stranded DNA exposed during transcription of switch (S) region sequences at the IgH locus. DNA lesions thus generated are processed by components of several general DNA repair pathways to drive CSR. Given that AID can instigate DNA lesions and genomic instability, stringent checks are imposed that constrain and restrict its mutagenic potential. In this review, we will discuss how AID expression and substrate specificity and activity is rigorously enforced at the transcriptional, post-transcriptional, post-translational, and epigenetic levels, and how the DNA-damage response is choreographed with precision to permit targeted activity while limiting bystander catastrophe. PMID:24734031

Underwater Robot Task Planning Using Multi-Objective Meta-Heuristics

PubMed Central

Landa-Torres, Itziar; Manjarres, Diana; Bilbao, Sonia; Del Ser, Javier

2017-01-01

Robotics deployed in the underwater medium are subject to stringent operational conditions that impose a high degree of criticality on the allocation of resources and the schedule of operations in mission planning. In this context the so-called cost of a mission must be considered as an additional criterion when designing optimal task schedules within the mission at hand. Such a cost can be conceived as the impact of the mission on the robotic resources themselves, which range from the consumption of battery to other negative effects such as mechanic erosion. This manuscript focuses on this issue by devising three heuristic solvers aimed at efficiently scheduling tasks in robotic swarms, which collaborate together to accomplish a mission, and by presenting experimental results obtained over realistic scenarios in the underwater environment. The heuristic techniques resort to a Random-Keys encoding strategy to represent the allocation of robots to tasks and the relative execution order of such tasks within the schedule of certain robots. The obtained results reveal interesting differences in terms of Pareto optimality and spread between the algorithms considered in the benchmark, which are insightful for the selection of a proper task scheduler in real underwater campaigns. PMID:28375160

Ensuring the safe and effective FDA regulation of fecal microbiota transplantation

PubMed Central

Sachs, Rachel E.; Edelstein, Carolyn A.

2015-01-01

Scientists, policymakers, and medical professionals alike have become increasingly worried about the rise of antibiotic resistance, and the growing number of infections due to bacteria like Clostridium difficile, which cause a significant number of deaths and are imposing increasing costs on our health care system. However, in the last few years, fecal microbiota transplantation (FMT), the transplantation of stool from a healthy donor into the bowel of a patient, has emerged as a startlingly effective means to treat recurrent C. difficile infections. At present, the FDA is proposing to regulate FMT as a biologic drug. However, this proposed classification is both underregulatory and overregulatory. The FDA's primary goal is to ensure that patients have access to safe, effective treatments—and as such they should regulate some aspects of FMT more stringently than they propose to, and others less so. This essay will examine the nature of the regulatory challenges the FDA will face in deciding to regulate FMT as a biologic drug, and will then evaluate available policy alternatives for the FDA to pursue, ultimately concluding that the FDA ought to consider adopting a hybrid regulatory model as it has done in the case of cord blood. PMID:27774199

Patterns of Stochastic Behavior in Dynamically Unstable High-Dimensional Biochemical Networks

PubMed Central

Rosenfeld, Simon

2009-01-01

The question of dynamical stability and stochastic behavior of large biochemical networks is discussed. It is argued that stringent conditions of asymptotic stability have very little chance to materialize in a multidimensional system described by the differential equations of chemical kinetics. The reason is that the criteria of asymptotic stability (Routh-Hurwitz, Lyapunov criteria, Feinberg’s Deficiency Zero theorem) would impose the limitations of very high algebraic order on the kinetic rates and stoichiometric coefficients, and there are no natural laws that would guarantee their unconditional validity. Highly nonlinear, dynamically unstable systems, however, are not necessarily doomed to collapse, as a simple Jacobian analysis would suggest. It is possible that their dynamics may assume the form of pseudo-random fluctuations quite similar to a shot noise, and, therefore, their behavior may be described in terms of Langevin and Fokker-Plank equations. We have shown by simulation that the resulting pseudo-stochastic processes obey the heavy-tailed Generalized Pareto Distribution with temporal sequence of pulses forming the set of constituent-specific Poisson processes. Being applied to intracellular dynamics, these properties are naturally associated with burstiness, a well documented phenomenon in the biology of gene expression. PMID:19838330

Distillery spent wash: treatment technologies and potential applications.

PubMed

Mohana, Sarayu; Acharya, Bhavik K; Madamwar, Datta

2009-04-15

Distillery spent wash is the unwanted residual liquid waste generated during alcohol production and pollution caused by it is one of the most critical environmental issue. Despite standards imposed on effluent quality, untreated or partially treated effluent very often finds access to watercourses. The distillery wastewater with its characteristic unpleasant odor poses a serious threat to the water quality in several regions around the globe. The ever-increasing generation of distillery spent wash on the one hand and stringent legislative regulations of its disposal on the other has stimulated the need for developing new technologies to process this effluent efficiently and economically. A number of clean up technologies have been put into practice and novel bioremediation approaches for treatment of distillery spent wash are being worked out. Potential microbial (anaerobic and aerobic) as well as physicochemical processes as feasible remediation technologies to combat environmental pollution are being explored. An emerging field in distillery waste management is exploiting its nutritive potential for production of various high value compounds. This review presents an overview of the pollution problems caused by distillery spent wash, the technologies employed globally for its treatment and its alternative use in various biotechnological sectors.

Underwater Robot Task Planning Using Multi-Objective Meta-Heuristics.

PubMed

Landa-Torres, Itziar; Manjarres, Diana; Bilbao, Sonia; Del Ser, Javier

2017-04-04

Robotics deployed in the underwater medium are subject to stringent operational conditions that impose a high degree of criticality on the allocation of resources and the schedule of operations in mission planning. In this context the so-called cost of a mission must be considered as an additional criterion when designing optimal task schedules within the mission at hand. Such a cost can be conceived as the impact of the mission on the robotic resources themselves, which range from the consumption of battery to other negative effects such as mechanic erosion. This manuscript focuses on this issue by devising three heuristic solvers aimed at efficiently scheduling tasks in robotic swarms, which collaborate together to accomplish a mission, and by presenting experimental results obtained over realistic scenarios in the underwater environment. The heuristic techniques resort to a Random-Keys encoding strategy to represent the allocation of robots to tasks and the relative execution order of such tasks within the schedule of certain robots. The obtained results reveal interesting differences in terms of Pareto optimality and spread between the algorithms considered in the benchmark, which are insightful for the selection of a proper task scheduler in real underwater campaigns.

Perception and intentions to quit among waterpipe smokers in Qatar: a cross-sectional survey

PubMed Central

Jaam, M.; Al-Marridi, W.; Fares, H.; Izham, M.; Kheir, N.

2016-01-01

Objective: To evaluate the perceptions and attitudes of waterpipe (shisha) smokers in Qatar regarding the health risks associated with addiction and to determine their intentions to quit. Methods: A cross-sectional survey was conducted among 181 self-reported waterpipe smokers. Participants were approached in public places as well as in shisha cafes in Qatar. The questionnaire included items related to perception, attitude and intention to quit. Both descriptive and inferential statistics were performed for data analyses, with P ≤ 0.05 considered statistically significant. Results: About 44% of the respondents believed that waterpipe smoking was safer than cigarette smoking, and more than 70% would not mind if their children became involved in waterpipe smoking. More than half of the current smokers wanted to quit smoking shisha at some point, and 17% identified health concerns as the main motivating factor for their intention to quit. Conclusion: A large proportion of shisha smokers viewed shisha as a safer alternative to cigarettes, yet they admitted to intending to quit. These findings underscore the need to design educational interventions and awareness campaigns as well as impose stringent laws on waterpipe smoking in public places in Qatar. PMID:27051611

Direct probe of the variability of Coulomb correlation in iron pnictide superconductors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vilmercati, P.; Parks Cheney, C.; Bondino, F.

2012-01-01

We use core-valence-valence Auger spectra to probe the Coulomb repulsion between holes in the valence band of Fe pnictide superconductors. By comparing the two-hole final-state spectra to density functional theory calculations of the single-particle density of states, we extract a measure of the electron correlations that exist in these systems. Our results show that the Coulomb repulsion is highly screened and can definitively be considered as weak. We also find that there are differences between the 1111 and 122 families and even a small variation as a function of the doping x in Ba(Fe{sub 1-x}Co{sub x}){sub 2}As{sub 2}. We discussmore » how the values of the hole-hole Coulomb repulsion obtained from our study relate to the onsite Coulomb parameter U used in model and first-principles calculations based on dynamical mean field theory and establish an upper bound for its effective value. Our results impose stringent constraints on model-based phase diagrams that vary with the quantity U or U/W by restricting the latter to a rather small range of values.« less

Benefit/cost comparison for utility SMES applications

NASA Astrophysics Data System (ADS)

Desteese, J. G.; Dagle, J. E.

1991-08-01

This paper summarizes eight case studies that account for the benefits and costs of superconducting magnetic energy storage (SMES) in system-specific utility applications. Four of these scenarios are hypothetical SMES applications in the Pacific Northwest, where relatively low energy costs impose a stringent test on the viability of the concept. The other four scenarios address SMES applications on high-voltage, direct-current (HVDC) transmission lines. While estimated SMES benefits are based on a previously reported methodology, this paper presents results of an improved cost-estimating approach that includes an assumed reduction in the cost of the power conditioning system (PCS) from approximately $160/kW to $80/kW. The revised approach results in all the SMES scenarios showing higher benefit/cost ratios than those reported earlier. However, in all but two cases, the value of any single benefit is still less than the unit's levelized cost. This suggests, as a general principle, that the total value of multiple benefits should always be considered if SMES is to appear cost effective in many utility applications. These results should offer utilities further encouragement to conduct more detailed analyses of SMES benefits in scenarios that apply to individual systems.

Mycotoxin contamination of animal feedingstuff: detoxification by gamma-irradiation and reduction of aflatoxins and ochratoxin A concentrations.

PubMed

Di Stefano, Vita; Pitonzo, Rosa; Cicero, Nicola; D'Oca, Maria Cristina

2014-01-01

Mycotoxins are fungal secondary metabolites identified in many agricultural products screened for toxigenic moulds. They have been reported to be carcinogenic, teratogenic, tremorogenic, haemorrhagic and dermatitic to a wide range of organisms. With the increasing stringent regulations for mycotoxins imposed by importing countries such as those of the European Union, many cereals that are not safe for human consumption are used in formulations intended for animal feed. Gamma-rays are reported in the scientific literature to destroy ochratoxin A and aflatoxin in food crops and feed. The present study provides preliminary data for establishing the effect of dose of gamma-irradiation, ranging from 0 to 15 kGy, on aflatoxins and ochratoxin A reduction in commercial animal feed. The mycotoxin levels were determined by means of immunoaffinity clean-up (IAC) and HPLC with fluorescence detection (HPLC-FLD). The maximum reductions found at 15 kGy were 23.9%, 18.2%, 11.0%, 21.1% and 13.6% for ochratoxin A, aflatoxin B₁, aflatoxin B₂, aflatoxin G₁ and aflatoxin G₂, respectively. Results showed that the gamma-rays even at 15 kGy were not effective in the complete destruction of ochratoxin A and aflatoxins in the tested feed.

Tilt-tuned etalon locking for tunable laser stabilization.

PubMed

Gibson, Bradley M; McCall, Benjamin J

2015-06-15

Locking to a fringe of a tilt-tuned etalon provides a simple, inexpensive method for stabilizing tunable lasers. Here, we describe the use of such a system to stabilize an external-cavity quantum cascade laser; the locked laser has an Allan deviation of approximately 1 MHz over a one-second integration period, and has a single-scan tuning range of approximately 0.4  cm(-1). The system is robust, with minimal alignment requirements and automated lock acquisition, and can be easily adapted to different wavelength regions or more stringent stability requirements with minor alterations.

Visualization of Computational Fluid Dynamics

NASA Technical Reports Server (NTRS)

Gerald-Yamasaki, Michael; Hultquist, Jeff; Bryson, Steve; Kenwright, David; Lane, David; Walatka, Pamela; Clucas, Jean; Watson, Velvin; Lasinski, T. A. (Technical Monitor)

1995-01-01

Scientific visualization serves the dual purpose of exploration and exposition of the results of numerical simulations of fluid flow. Along with the basic visualization process which transforms source data into images, there are four additional components to a complete visualization system: Source Data Processing, User Interface and Control, Presentation, and Information Management. The requirements imposed by the desired mode of operation (i.e. real-time, interactive, or batch) and the source data have their effect on each of these visualization system components. The special requirements imposed by the wide variety and size of the source data provided by the numerical simulation of fluid flow presents an enormous challenge to the visualization system designer. We describe the visualization system components including specific visualization techniques and how the mode of operation and source data requirements effect the construction of computational fluid dynamics visualization systems.

42 CFR 421.5 - General provisions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... U.S. Revised Statutes or any other provision of law that requires competitive bidding. (b.... (a) Competitive bidding not required for carriers. CMS may enter into contracts with carriers, or... certain administrative responsibilities that the law imposes. Accordingly, their agreements and contracts...

42 CFR 421.5 - General provisions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... U.S. Revised Statutes or any other provision of law that requires competitive bidding. (b.... (a) Competitive bidding not required for carriers. CMS may enter into contracts with carriers, or... certain administrative responsibilities that the law imposes. Accordingly, their agreements and contracts...

Modeling material failure during cab car end frame impact

DOT National Transportation Integrated Search

2009-03-03

New standards have been proposed to increase the strength requirements for cab car end structures and impose further requirements on their ability to absorb energy during a grade-crossing collision. This conference paper reports on a set of full-scal...

20 CFR 437.6 - Additions and exceptions.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Employees' Benefits SOCIAL SECURITY ADMINISTRATION UNIFORM ADMINISTRATIVE REQUIREMENTS FOR GRANTS AND... classes of grants and grantees subject to this part, SSA may not impose additional administrative requirements except in codified regulations published in the Federal Register. (b) Exceptions for classes of...

Tunable, Flexible and Efficient Optimization of Control Pulses for Superconducting Qubits, part I - Theory

NASA Astrophysics Data System (ADS)

Machnes, Shai; AsséMat, Elie; Tannor, David; Wilhelm, Frank

Quantum computation places very stringent demands on gate fidelities, and experimental implementations require both the controls and the resultant dynamics to conform to hardware-specific ansatzes and constraints. Superconducting qubits present the additional requirement that pulses have simple parametrizations, so they can be further calibrated in the experiment, to compensate for uncertainties in system characterization. We present a novel, conceptually simple and easy-to-implement gradient-based optimal control algorithm, GOAT, which satisfies all the above requirements. In part II we shall demonstrate the algorithm's capabilities, by using GOAT to optimize fast high-accuracy pulses for two leading superconducting qubits architectures - Xmons and IBM's flux-tunable couplers.

Diffraction based overlay metrology for α-carbon applications

NASA Astrophysics Data System (ADS)

Saravanan, Chandra Saru; Tan, Asher; Dasari, Prasad; Goelzer, Gary; Smith, Nigel; Woo, Seouk-Hoon; Shin, Jang Ho; Kang, Hyun Jae; Kim, Ho Chul

2008-03-01

Applications that require overlay measurement between layers separated by absorbing interlayer films (such as α- carbon) pose significant challenges for sub-50nm processes. In this paper scatterometry methods are investigated as an alternative to meet these stringent overlay metrology requirements. In this article, a spectroscopic Diffraction Based Overlay (DBO) measurement technique is used where registration errors are extracted from specially designed diffraction targets. DBO measurements are performed on detailed set of wafers with varying α-carbon (ACL) thicknesses. The correlation in overlay values between wafers with varying ACL thicknesses will be discussed. The total measurement uncertainty (TMU) requirements for these layers are discussed and the DBO TMU results from sub-50nm samples are reviewed.

40 CFR 91.1108 - In-use compliance provisions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... comply in all respects with the requirements of subpart I of this part. (2) Any notification required to... manufacturer bears all cost obligation a dealer incurs as a result of a requirement imposed by paragraph (a) of... franchise or other agreement is prohibited. (c) If a manufacturer includes in an advertisement a statement...

Toward the Standardization of Bioreactors for Space Research

NASA Astrophysics Data System (ADS)

Garcia, Michel; Nebuloni, Stefano; Dainesi, Paolo; Gass, Samuel

Growing interest in long-term human space missions and exploration as well as future plans for extra-terrestrial human settlements, places increasing importance on understanding biological and chemical processes in space at cellular and molecular level. RUAG Space has been involved in the development of bioreactors for life-science experiments in space for the past 20 years. Throughout these developments, RUAG has acted as the link between scientists and the space industry, translating high-level scientific requirements into technical requirements, verifying their feasibility within the space context, and developing state-of-the-art experiment hardware which can interface with dedicated micro-gravity platform. Although this approach has brought forth promising developments in the field, it is associated to very long development phases as well as correspondingly high costs. Each new scientific experiment is often associated to an entirely new hardware development. This is, in large, due to the limited information available on the possibilities and constraints imposed by the particular context of space. Therefore, a considerable amount of time and development costs are invested in order to accommodate stringent scientific requirements and/or specific experiment design in space hardware. This does not only have an impact on funding opportunities for micro-gravity experiments in space, it also curbs the pace of scientific discoveries and limits the number of research opportunities. Therefore, in the following, we present an overview of already established possibilities for cellular research in space, with special emphasis on hardware developed by RUAG Space. This is intended to provide scientists with key technical information on already existing bioreactors, subsystems, and components, which may be used as a basis when designing scientific studies. By considering this information from the onset of the establishment of scientific requirements, technical solutions can be implemented which do not require major new and lengthy developments. RUAG believes this is pivotal in facilitating access to life-science research in space and thereby increasing scientific output in this research area. The overview includes a description of technical features such as feasible cultivation volumes in highly biocompatible and transparent culture chambers, cultivation method options (batch vs. continuous), associated feed rates, and chemical fixation methods. Feasible regulation and sensing possibilities (i.e. O2, CO2, temperature, pH, cell concentration), based on technologies already used in laboratory application, are also discussed. Important aspects related to flow homogeneity, mass/gas transfer and mixing methods in micro-gravity are also presented. Lastly, the environmental performance of existing bioreactors is also shown and a particular emphasis is placed on safety design aspects for space hardware.

The Budget Scoring Alternatives Financing Methods for Defense Requirements

DTIC Science & Technology

2007-04-30

The government grants a franchise to a private partner to finance, design, build and operate a facility for a specific period of time. Ownership of...of an automobile from Avis implies no ownership . However, leases can be structured in an almost limitless number of complex arrangements in which...satisfy the following stringent criteria: Ownership of the asset remains with the lessor during the term of the lease and is not transferred to the

Aberration correction results in the IBM STEM instrument.

PubMed

Batson, P E

2003-09-01

Results from the installation of aberration correction in the IBM 120 kV STEM argue that a sub-angstrom probe size has been achieved. Results and the experimental methods used to obtain them are described here. Some post-experiment processing is necessary to demonstrate the probe size of about 0.078 nm. While the promise of aberration correction is demonstrated, we remain at the very threshold of practicality, given the very stringent stability requirements.

Fabrication and Improvement of Lmsc's All-silica RSI

NASA Technical Reports Server (NTRS)

Beasley, R. M.; Izu, Y. D.; Nakano, H. N.; Ozolin, A. A.; Peachman, A.

1973-01-01

The LI-1500 and LI-900 all silica RSI materials have made the transition from laboratory to manufacturing operation. Improvements in both quality and reproducibility have been achieved. The LI-1500 material has displayed superior reliability in evaluations conducted at various facilities. The dependable performance of the material is attributed to the adherence to the stringent requirements of the numerous material, process, and product control evaluations and inspection points performed during manufacture.

Modular Wireless Data-Acquisition and Control System

NASA Technical Reports Server (NTRS)

Perotti, Jose; Lucena, Angel; Medelius, Pedro; Mata, Carlos; Eckhoff, Anthony; Blalock, Norman

2004-01-01

A modular wireless data-acquisition and control system, now in operation at Kennedy Space Center, offers high performance at relatively low cost. The system includes a central station and a finite number of remote stations that communicate with each other through low-power radio frequency (RF) links. Designed to satisfy stringent requirements for reliability, integrity of data, and low power consumption, this system could be reproduced and adapted to use in a broad range of settings.

A Superior Kirchhoff Method for Aeroacoustic Noise Prediction: The Ffowcs Williams-Hawkings Equation

NASA Technical Reports Server (NTRS)

Brentner, Kenneth S.

1997-01-01

The prediction of aeroacoustic noise is important; all new aircraft must meet noise certification requirements. Local noise standards can be even more stringent. The NASA noise reduction goal is to reduce perceived noise levels by a factor of two in 10 years. The objective of this viewgraph presentation is to demonstrate the superiority of the FW-H approach over the Kirchoff method for aeroacoustics, both analytically and numerically.

The DHEW Requirements for the Protection of Human Subjects: Analysis and Impact at the University of California, Berkeley. One of a Series of Analysis and Impact Reports of Major Federal Requirements Areas.

ERIC Educational Resources Information Center

Millstein, Eugene J.

This project identifies institutional research management problems imposed by certain requirements of the sponsoring Federal agencies; assesses the impact on the institution when meeting the requirements; and, where appropriate, recommends standardization or modification of the requirements or their implementation. One fundamental DHEW requirement…