Stress-Intensity Factors for Elliptical Cracks Emanating from Countersunk Rivet Holes

DOT National Transportation Integrated Search

1998-04-01

Small cracks developing from rivet holes in lap joints of fuselage structure have been an issue of concern over the past decade. Stress-intensity factor solutions required to assess the structural integrity of such configurations are lacking. To addr...

Model reduction in integrated controls-structures design

NASA Technical Reports Server (NTRS)

Maghami, Peiman G.

1993-01-01

It is the objective of this paper to present a model reduction technique developed for the integrated controls-structures design of flexible structures. Integrated controls-structures design problems are typically posed as nonlinear mathematical programming problems, where the design variables consist of both structural and control parameters. In the solution process, both structural and control design variables are constantly changing; therefore, the dynamic characteristics of the structure are also changing. This presents a problem in obtaining a reduced-order model for active control design and analysis which will be valid for all design points within the design space. In other words, the frequency and number of the significant modes of the structure (modes that should be included) may vary considerably throughout the design process. This is also true as the locations and/or masses of the sensors and actuators change. Moreover, since the number of design evaluations in the integrated design process could easily run into thousands, any feasible order-reduction method should not require model reduction analysis at every design iteration. In this paper a novel and efficient technique for model reduction in the integrated controls-structures design process, which addresses these issues, is presented.

Integrating Sex and Drugs into the Principles Course: Market-Failures versus Failures-of-Market Outcomes.

ERIC Educational Resources Information Center

Colander, David

2003-01-01

Argues that microeconomics principles courses are structured around an approach to policy that avoids many controversial but central policy issues including: the interplay of moral issues and efficiency; questions of consumer sovereignty; and questions of the interrelation between measures of efficiency and income distribution. Suggests a dual…

Scope of Policy Issues in eHealth: Results From a Structured Literature Review

PubMed Central

Durrani, Hammad; Nayani, Parvez; Fahim, Ammad

2012-01-01

Background eHealth is widely used as a tool for improving health care delivery and information. However, distinct policies and strategies are required for its proper implementation and integration at national and international levels. Objective To determine the scope of policy issues faced by individuals, institutions, or governments in implementing eHealth programs. Methods We conducted a structured review of both peer-reviewed and gray literature from 1998–2008. A Medline search for peer-reviewed articles found 40 papers focusing on different aspects of eHealth policy. In addition, a Google search found 20 national- and international-level policy papers and documents. We reviewed these articles to extract policy issues and solutions described at different levels of care. Results The literature search found 99 policy issues related to eHealth. We grouped these issues under the following themes: (1) networked care, (2) interjurisdictional practice, (3) diffusion of eHealth/digital divide, (4) eHealth integration with existing systems, (5) response to new initiatives, (6) goal-setting for eHealth policy, (7) evaluation and research, (8) investment, and (9) ethics in eHealth. Conclusions We provide a list of policy issues that should be understood and addressed by policy makers at global, jurisdictional, and institutional levels, to facilitate smooth and reliable planning of eHealth programs. PMID:22343270

Propulsion/airframe integration issues for waverider aircraft

NASA Technical Reports Server (NTRS)

Blankson, Isaiah M.; Hagseth, Paul

1993-01-01

While many propulsion concepts and technologies developed for nonwaverider-type hypersonic vehicles may apply to waveriders, some aspects of these configurations require unique technological approaches. An evaluation is made of such distinctive opportunities in the cases of engine cycle selection, inlets, nozzle designs and integration, longitudinal stability, and thermal management. Also discussed are waverider requirements for control surface effectiveness, inlet boundary layer ingestion effects, and structural/configurational optimization, giving attention to trades in volumetric/structural efficiency and vehicle L/D.

Pre-integrated structures for Space Station Freedom

NASA Technical Reports Server (NTRS)

Cruz, Jonathan N.; Monell, Donald W.; Mutton, Philip; Troutman, Patrick A.

1991-01-01

An in-space construction (erectable) approach to assembling Freedom is planned but the increasing complexity of the station design along with a decrease in shuttle capability over the past several years has led to an assembly sequence that requires more resources (EVA, lift, volume) than the shuttle can provide given a fixed number of flights. One way to address these issues is to adopt a pre-integrated approach to assembling Freedom. A pre-integrated approach combines station primary structure and distributed systems into discrete sections that are assembled and checked out on the ground. The section is then launched as a single structural entity on the shuttle and attached to the orbiting station is then launched as a single structural entity on the shuttle and attached to the orbiting station with a minimum of EVA. The feasibility of a pre-integrated approach to assembling Freedon is discussed. The structural configuration, packaging, and shuttle integration of discrete pre-integrated elements for Freedom assembly are discussed. It is shown that the pre-integrated approach to assembly reduces EVA and increases shuttle margin with respect to mass, volume, and center of gravity limits when compared to the baseline Freedom assembly sequence.

An integrated modeling and design tool for advanced optical spacecraft

NASA Technical Reports Server (NTRS)

Briggs, Hugh C.

1992-01-01

Consideration is given to the design and status of the Integrated Modeling of Optical Systems (IMOS) tool and to critical design issues. A multidisciplinary spacecraft design and analysis tool with support for structural dynamics, controls, thermal analysis, and optics, IMOS provides rapid and accurate end-to-end performance analysis, simulations, and optimization of advanced space-based optical systems. The requirements for IMOS-supported numerical arrays, user defined data structures, and a hierarchical data base are outlined, and initial experience with the tool is summarized. A simulation of a flexible telescope illustrates the integrated nature of the tools.

Integration of Youth into the Labor Market: Some Theoretical Considerations on a Structural/Conjunctural Issue.

ERIC Educational Resources Information Center

Laflamme, Claude; Baby, Antoine

1993-01-01

Presents a model of youth transition from education to work that takes into account the disrupting effects of global economic crisis and massive computerization. Suggests that investment in new technologies reduces employment and polarizes remaining jobs to unskilled and highly skilled categories. Discusses psychosocial integration strategies…

Issues and Strategies for Establishing Work-Integrated Learning for Multidisciplinary Teams: A Focus on Degrees in Sustainability

ERIC Educational Resources Information Center

Wilson, Robyn Fay

2015-01-01

This study was conducted to identify challenges and potential strategies to streamline work-integrated learning placements for multidisciplinary teams of students undertaking degrees in sustainability. Face-to-face interviews using a semi-structured questionnaire were conducted with 15 academics and senior university staff, from four universities…

Integrated and Early Childhood Education: Preparation for Social Development.

ERIC Educational Resources Information Center

Chitepo, Victoria

This keynote address first briefly reviews the historical nature and structure of education in Zimbabwe prior to independence. Then, the theme of the seminar (integrated education as a preparation for social development), as well as related policy issues are stated. Educational goals of the government of Zimbabwe are discussed. Concluding remarks…

Formation of integrated structural units using the systematic and integrated method when implementing high-rise construction projects

NASA Astrophysics Data System (ADS)

Abramov, Ivan

2018-03-01

Development of design documentation for a future construction project gives rise to a number of issues with the main one being selection of manpower for structural units of the project's overall implementation system. Well planned and competently staffed integrated structural construction units will help achieve a high level of reliability and labor productivity and avoid negative (extraordinary) situations during the construction period eventually ensuring improved project performance. Research priorities include the development of theoretical recommendations for enhancing reliability of a structural unit staffed as an integrated construction crew. The author focuses on identification of destabilizing factors affecting formation of an integrated construction crew; assessment of these destabilizing factors; based on the developed mathematical model, highlighting the impact of these factors on the integration criterion with subsequent identification of an efficiency and reliability criterion for the structural unit in general. The purpose of this article is to develop theoretical recommendations and scientific and methodological provisions of an organizational and technological nature in order to identify a reliability criterion for a structural unit based on manpower integration and productivity criteria. With this purpose in mind, complex scientific tasks have been defined requiring special research, development of corresponding provisions and recommendations based on the system analysis findings presented herein.

Using image mapping towards biomedical and biological data sharing

PubMed Central

2013-01-01

Image-based data integration in eHealth and life sciences is typically concerned with the method used for anatomical space mapping, needed to retrieve, compare and analyse large volumes of biomedical data. In mapping one image onto another image, a mechanism is used to match and find the corresponding spatial regions which have the same meaning between the source and the matching image. Image-based data integration is useful for integrating data of various information structures. Here we discuss a broad range of issues related to data integration of various information structures, review exemplary work on image representation and mapping, and discuss the challenges that these techniques may bring. PMID:24059352

Issues of Structure and Issues of Scale in Assessment from a Situative/Sociocultural Perspective. CSE Technical Report 668

ERIC Educational Resources Information Center

Mislevy, Robert J.

2006-01-01

A situated/sociocultural (SC) view of assessment "emphasizes questions about the quality of students' participation in activities of inquiry and sense-making, and considers assessment practices as integral components of the general systems of activity in which they occur" (Greeno, Collins, & Resnick, 1997, p. 36). This presentation addresses two…

Technical and Practical Issues in the Structure and Clinical Invariance of the Wechsler Scales: A Rejoinder to Commentaries

ERIC Educational Resources Information Center

Weiss, Lawrence G.; Keith, Timothy Z.; Zhu, Jianjun; Chen, Hsinyi

2013-01-01

This discussion article addresses issues related to expansion of the Wechsler model from four to five factors; multiple broad CHC abilities measured by the Arithmetic subtest; advantages and disadvantages of including complex tasks requiring integration of multiple broad abilities when measuring intelligence; limitations of factor analysis, which…

Processing of intended and unintended strategic issues and integration into the strategic agenda.

PubMed

Ridder, Hans-Gerd; Schrader, Jan Simon

2017-11-01

Strategic change is needed in hospitals due to external and internal pressures. However, research on strategic change, as a combination of management and medical expertise in hospitals, remains scarce. We analyze how intended strategic issues are processed into deliberate strategies and how unintended strategic issues are processed into emergent strategies in the management of strategy formation in hospitals. This study empirically investigates the integration of medical and management expertise in strategy formation. The longitudinal character of the case study enabled us to track patterns of intended and unintended strategic issues over 2 years. We triangulated data from interviews, observations, and documents. In accordance with the quality standards of qualitative research procedures, we analyzed the data by pattern matching and provided analytical generalization regarding strategy formation in hospitals. Our findings suggest that strategic issues are particularly successful within the strategy formation process if interest groups are concerned with the strategic issue, prospective profits are estimated, and relevant decisions makers are involved early on. Structure and interaction processes require clear criteria and transparent procedures for effective strategy formation. There is systematic neglect of medical expertise in processes of generating strategies. Our study reveals that the decentralized structure of medical centers is an adequate template for both the operationalization of intended strategic issues and the development of unintended strategic issues. However, tasks, roles, responsibility, resources, and administrative support are necessary for effective management of strategy formation. Similarly, criteria, procedures, and decision-making are prerequisites for effective strategy formation.

Structuring a Clinical Learning Environment for a Hybrid-PBL Dental Curriculum.

ERIC Educational Resources Information Center

MacNeil, M. A. J.; Walton, Joanne N.; Clark, D. Christopher; Tobias, David L.; Harrison, Rosamund L.

1998-01-01

Describes the evolution and implementation of a joint medical-dental problem-based learning (PBL) curriculum at the University of British Columbia's medical and dental schools, featuring development of an integrated care clinic. Issues in structuring the new curriculum are discussed, including management of the clinic's group practices, affective…

The challenging scales of the bird: Shuttle tile structural integrity

NASA Technical Reports Server (NTRS)

Schneider, W. C.; Miller, G. J.

1985-01-01

The principal design issues, tests, and analyses required to solve the tile integrity problem on the space shuttle orbiters are addressed. Proof testing of installed tiles is discussed along with an airflow test of special tiles. Orbiter windshield tiles are considered in terms of changes necessary to ensure acceptable margins of safety for flight.

Structural integrity of engineering composite materials: a cracking good yarn.

PubMed

Beaumont, Peter W R; Soutis, Costas

2016-07-13

Predicting precisely where a crack will develop in a material under stress and exactly when in time catastrophic fracture of the component will occur is one the oldest unsolved mysteries in the design and building of large-scale engineering structures. Where human life depends upon engineering ingenuity, the burden of testing to prove a 'fracture safe design' is immense. Fitness considerations for long-life implementation of large composite structures include understanding phenomena such as impact, fatigue, creep and stress corrosion cracking that affect reliability, life expectancy and durability of structure. Structural integrity analysis treats the design, the materials used, and figures out how best components and parts can be joined, and takes service duty into account. However, there are conflicting aims in the complete design process of designing simultaneously for high efficiency and safety assurance throughout an economically viable lifetime with an acceptable level of risk. This article is part of the themed issue 'Multiscale modelling of the structural integrity of composite materials'. © 2016 The Author(s).

Responses to GM food content in context with food integrity issues: results from Australian population surveys.

PubMed

Mohr, Philip; Golley, Sinéad

2016-01-25

This study examined community responses to use of genetically modified (GM) content in food in the context of responses to familiar food additives by testing an empirically and theoretically derived model of the predictors of responses to both GM content and food integrity issues generally. A nationwide sample of 849 adults, selected at random from the Australian Electoral Roll, responded to a postal Food and Health Survey. Structural equation modelling analyses confirmed that ratings of general concern about food integrity (related to the presence of preservatives and other additives) strongly predicted negativity towards GM content. Concern about food integrity was, in turn, predicted by environmental concern and health engagement. In addition, both concern about food integrity generally and responses to GM content specifically were weakly predicted by attitudes to benefits of science and an intuitive (i.e., emotionally-based) reasoning style. Data from a follow-up survey conducted under the same conditions (N=1184) revealed that ratings of concern were significantly lower for use of genetic engineering in food than for four other common food integrity issues examined. Whereas the question of community responses to GM is often treated as a special issue, these findings support the conclusion that responses to the concept of GM content in food in Australia are substantially a specific instance of a general sensitivity towards the integrity of the food supply. They indicate that the origins of responses to GM content may be largely indistinguishable from those of general responses to preservatives and other common food additives. Copyright © 2015 Elsevier B.V. All rights reserved.

Inflatable Structures Technology Handbook. Chapter 21; Inflatable Habitats

NASA Technical Reports Server (NTRS)

Kennedy, Kriss J.; Raboin, Jasen; Spexarth, Gary; Valle, Gerard

2000-01-01

The technologies required to design, fabricate, and utilize an inflatable module for space applications has been demonstrated and proven by the TransHab team during the development phase of the program. Through testing and hands-on development several issues about inflatable space structures have been addressed , such as: ease of manufacturing, structural integrity, micrometeorite protection, folding , and vacuum deployment. The TransHab inflatable technology development program has proven that not only are inflatable structures a viable option, but they also offer significant advantages over conventional metallic structures.

Organizing the public health-clinical health interface: theoretical bases.

PubMed

St-Pierre, Michèle; Reinharz, Daniel; Gauthier, Jacques-Bernard

2006-01-01

This article addresses the issue of the interface between public health and clinical health within the context of the search for networking approaches geared to a more integrated delivery of health services. The articulation of an operative interface is complicated by the fact that the definition of networking modalities involves complex intra- and interdisciplinary and intra- and interorganizational systems across which a new transversal dynamics of intervention practices and exchanges between service structures must be established. A better understanding of the situation is reached by shedding light on the rationale underlying the organizational methods that form the bases of the interface between these two sectors of activity. The Quebec experience demonstrates that neither the structural-functionalist approach, which emphasizes remodelling establishment structures and functions as determinants of integration, nor the structural-constructivist approach, which prioritizes distinct fields of practice in public health and clinical health, adequately serves the purpose of networking and integration. Consequently, a theoretical reframing is imperative. In this regard, structuration theory, which fosters the simultaneous study of methods of inter-structure coordination and inter-actor cooperation, paves the way for a better understanding of the situation and, in turn, to the emergence of new integration possibilities.

Demonstration and Methodology of Structural Monitoring of Stringer Runs out Composite Areas by Embedded Optical Fiber Sensors and Connectors Integrated during Production in a Composite Plant.

PubMed

Miguel Giraldo, Carlos; Zúñiga Sagredo, Juan; Sánchez Gómez, José; Corredera, Pedro

2017-07-21

Embedding optical fibers sensors into composite structures for Structural Health Monitoring purposes is not just one of the most attractive solutions contributing to smart structures, but also the optimum integration approach that insures maximum protection and integrity of the fibers. Nevertheless this intended integration level still remains an industrial challenge since today there is no mature integration process in composite plants matching all necessary requirements. This article describes the process developed to integrate optical fiber sensors in the Production cycle of a test specimen. The sensors, Bragg gratings, were integrated into the laminate during automatic tape lay-up and also by a secondary bonding process, both in the Airbus Composite Plant. The test specimen, completely representative of the root joint of the lower wing cover of a real aircraft, is comprised of a structural skin panel with the associated stringer run out. The ingress-egress was achieved through the precise design and integration of miniaturized optical connectors compatible with the manufacturing conditions and operational test requirements. After production, the specimen was trimmed, assembled and bolted to metallic plates to represent the real triform and buttstrap, and eventually installed into the structural test rig. The interrogation of the sensors proves the effectiveness of the integration process; the analysis of the strain results demonstrate the good correlation between fiber sensors and electrical gauges in those locations where they are installed nearby, and the curvature and load transfer analysis in the bolted stringer run out area enable demonstration of the consistency of the fiber sensors measurements. In conclusion, this work presents strong evidence of the performance of embedded optical sensors for structural health monitoring purposes, where in addition and most importantly, the fibers were integrated in a real production environment and the ingress-egress issue was solved by the design and integration of miniaturized connectors compatible with the manufacturing and structural test phases.

Demonstration and Methodology of Structural Monitoring of Stringer Runs out Composite Areas by Embedded Optical Fiber Sensors and Connectors Integrated during Production in a Composite Plant

PubMed Central

Miguel Giraldo, Carlos; Zúñiga Sagredo, Juan; Sánchez Gómez, José; Corredera, Pedro

2017-01-01

Embedding optical fibers sensors into composite structures for Structural Health Monitoring purposes is not just one of the most attractive solutions contributing to smart structures, but also the optimum integration approach that insures maximum protection and integrity of the fibers. Nevertheless this intended integration level still remains an industrial challenge since today there is no mature integration process in composite plants matching all necessary requirements. This article describes the process developed to integrate optical fiber sensors in the Production cycle of a test specimen. The sensors, Bragg gratings, were integrated into the laminate during automatic tape lay-up and also by a secondary bonding process, both in the Airbus Composite Plant. The test specimen, completely representative of the root joint of the lower wing cover of a real aircraft, is comprised of a structural skin panel with the associated stringer run out. The ingress-egress was achieved through the precise design and integration of miniaturized optical connectors compatible with the manufacturing conditions and operational test requirements. After production, the specimen was trimmed, assembled and bolted to metallic plates to represent the real triform and buttstrap, and eventually installed into the structural test rig. The interrogation of the sensors proves the effectiveness of the integration process; the analysis of the strain results demonstrate the good correlation between fiber sensors and electrical gauges in those locations where they are installed nearby, and the curvature and load transfer analysis in the bolted stringer run out area enable demonstration of the consistency of the fiber sensors measurements. In conclusion, this work presents strong evidence of the performance of embedded optical sensors for structural health monitoring purposes, where in addition and most importantly, the fibers were integrated in a real production environment and the ingress-egress issue was solved by the design and integration of miniaturized connectors compatible with the manufacturing and structural test phases. PMID:28754009

From gender bias to gender awareness in medical education.

PubMed

Verdonk, Petra; Benschop, Yvonne W M; de Haes, Hanneke C J M; Lagro-Janssen, Toine L M

2009-03-01

Gender is an essential determinant of health and illness. Gender awareness in doctors contributes to equity and equality in health and aims towards better health for men and women. Nevertheless, gender has largely been ignored in medicine. First, it is stated that medicine was 'gender blind' by not considering gender whenever relevant. Secondly, medicine is said to be 'male biased' because the largest body of knowledge on health and illness is about men and their health. Thirdly, gender role ideology negatively influences treatment and health outcomes. Finally, gender inequality has been overlooked as a determinant of health and illness. The uptake of gender issues in medical education brings about specific challenges for several reasons. For instance, the political-ideological connotations of gender issues create resistance especially in traditionalists in medical schools. Secondly, it is necessary to clarify which gender issues must be integrated in which domains. Also, some are interdisciplinary issues and as such more difficult to integrate. Finally, schools need assistance with implementation. The integration of psychosocial issues along with biomedical ones in clinical cases, the dissemination of literature and education material, staff education, and efforts towards structural embedding of gender in curricula are determining factors for successful implementation. Gender equity is not a spontaneous process. Medical education provides specific opportunities that may contribute to transformation for medical schools educate future doctors for future patients in future settings. Consequently, future benefits legitimize the integration of gender as a qualitative investment in medical education.

Extending the theoretical framework for curriculum integration in pre-clinical medical education.

PubMed

Vergel, John; Stentoft, Diana; Montoya, Juny

2017-08-01

Curriculum integration is widely discussed in medical education but remains ill defined. Although there is plenty of information on logistical aspects of curriculum integration, little attention has been paid to the contextual issues that emerge from its practice and may complicate students' knowledge integration. Therefore, we aimed to uncover how curriculum integration is manifested through context. We collected data from the official curriculum and interviewed ten participants (including curriculum designers, facilitators, and students) in the bachelor's medical program at Aalborg University. We observed various learning activities focused on pre-clinical education. Inspired by grounded theory, we analyzed the information we gathered. The following theoretical constructs emerged after the inductive analysis: 1) curriculum integration complexity is embedded in the institutional learning perspectives; 2) curriculum integration is used to harmonize conflicting learning perspectives in curriculum practice; 3) curriculum integration creates tensions that self-organize its structure; and 4) curriculum integration becomes visible in collaborative learning spaces. These constructs provide a framework for analyzing curriculum integration in the context in which it is meant to appear, which may assist educationalists to gain a more specific understanding of the term. This may enable effective curriculum integration since contextual issues are addressed in addition to the goals specified in the official curriculum.

Introduction to a special issue on concept mapping.

PubMed

Trochim, William M; McLinden, Daniel

2017-02-01

Concept mapping was developed in the 1980s as a unique integration of qualitative (group process, brainstorming, unstructured sorting, interpretation) and quantitative (multidimensional scaling, hierarchical cluster analysis) methods designed to enable a group of people to articulate and depict graphically a coherent conceptual framework or model of any topic or issue of interest. This introduction provides the basic definition and description of the methodology for the newcomer and describes the steps typically followed in its most standard canonical form (preparation, generation, structuring, representation, interpretation and utilization). It also introduces this special issue which reviews the history of the methodology, describes its use in a variety of contexts, shows the latest ways it can be integrated with other methodologies, considers methodological advances and developments, and sketches a vision of the future of the method's evolution. Copyright © 2016 Elsevier Ltd. All rights reserved.

A strategic value management approach for energy and maintenance management in a building

NASA Astrophysics Data System (ADS)

Nawi, Mohd Nasrun Mohd; Dahlan, Nofri Yenita; Nadarajan, Santhirasegaran

2015-05-01

Fragmentation process is always been highlighted by the stakeholders in the construction industry as one of the `critical' issue that diminishing the opportunity for stakeholders that involved during the operation and maintenance stage to influence design decisions. Failure of design professionals to consider how a maintenance contractor or facility manager will construct the design thus results in higher operating cost, wastage, defects during the maintenance and operation process. Moving towards team integration is considered a significant strategy for overcoming the issue. Value Management is a style of management dedicated to guiding people and promoting innovation with the aim to improve overall building performance through structured, team-oriented exercises which make explicit, and appraise subsequent decisions, by reference to the value requirements of the clients. Accordingly, this paper discusses the fragmentation issue in more detail including the definition, causes and effects to the maintenance and operation of building and at the same time will highlighted the potential of VM integrated team approach as a strategic management approach for overcoming that issue. It also explores that the team integration strategy alleviates scheduling problems, delays and disputes during the construction process, and, hence, prevent harming the overall building performance.

Key issues in application of composites to transport aircraft

NASA Technical Reports Server (NTRS)

Stone, M.

1978-01-01

The application of composite materials to transport aircraft was identified and reviewed including the major contributing disciplines of design, manufacturing, and processing. Factors considered include: crashworthiness considerations (structural integrity, postcrash fires, and structural fusing), electrical/avionics subsystems integration, lightning, and P-static protection design; manufacturing development, evaluation, selection, and refining of tooling and curing procedures; and major joint design considerations. Development of the DC-10 rudder, DC-10 vertical stabilizer, and the DC-9 wing study project was reviewed. The Federal Aviation Administration interface and the effect on component design of compliance with Federal Aviation Regulation 25 Composite Guidelines are discussed.

Active vibration control techniques for flexible space structures

NASA Technical Reports Server (NTRS)

Parlos, Alexander G.; Jayasuriya, Suhada

1990-01-01

Two proposed control system design techniques for active vibration control in flexible space structures are detailed. Control issues relevant only to flexible-body dynamics are addressed, whereas no attempt was made to integrate the flexible and rigid-body spacecraft dynamics. Both of the proposed approaches revealed encouraging results; however, further investigation of the interaction of the flexible and rigid-body dynamics is warranted.

Structures technology for a new generation of rotorcraft

NASA Technical Reports Server (NTRS)

Bartlett, Felton D., Jr.

1989-01-01

This paper presents an overview of structures research at the U. S. Army Aerostructures Directorate. The objectives of this research are to investigate, explore, and demonstrate emerging technologies that will provide lighter, safer, more survivable, and more cost-effective structures for rotorcraft in the 1990s and beyond. The emphasis of today's R&D is to contribute proven structures technology to the U. S. rotorcraft industry and Army aviation that directly impacts tomorrow's fleet readiness and mission capabilities. The primary contributor toward meeting these challenges is the development of high-strength and durable composites to minimize structural weight while maximizing cost effectiveness. Special aviation issues such as delamination of dynamic components, impact damage to thin skins, crashworthiness, and affordable manufacturing need to be resolved before the full potential of composites technology can be realized. To that end, this paper highlights research into composites structural integrity, crashworthiness, and materials applications which addresses these issues.

Vehicle/engine integration. [orbit transfer vehicles

NASA Technical Reports Server (NTRS)

Cooper, L. P.; Vinopal, T. J.; Florence, D. E.; Michel, R. W.; Brown, J. R.; Bergeron, R. P.; Weldon, V. A.

1984-01-01

VEHICLE/ENGINE Integration Issues are explored for orbit transfer vehicles (OTV's). The impact of space basing and aeroassist on VEHICLE/ENGINE integration is discussed. The AOTV structure and thermal protection subsystem weights were scaled as the vehicle length and surface was changed. It is concluded that for increased allowable payload lengths in a ground-based system, lower length-to-diameter (L/D) is as important as higher mixture ration (MR) in the range of mid L/D ATOV's. Scenario validity, geometry constraints, throttle levels, reliability, and servicing are discussed in the context of engine design and engine/vehicle integration.

On finite element implementation and computational techniques for constitutive modeling of high temperature composites

NASA Technical Reports Server (NTRS)

Saleeb, A. F.; Chang, T. Y. P.; Wilt, T.; Iskovitz, I.

1989-01-01

The research work performed during the past year on finite element implementation and computational techniques pertaining to high temperature composites is outlined. In the present research, two main issues are addressed: efficient geometric modeling of composite structures and expedient numerical integration techniques dealing with constitutive rate equations. In the first issue, mixed finite elements for modeling laminated plates and shells were examined in terms of numerical accuracy, locking property and computational efficiency. Element applications include (currently available) linearly elastic analysis and future extension to material nonlinearity for damage predictions and large deformations. On the material level, various integration methods to integrate nonlinear constitutive rate equations for finite element implementation were studied. These include explicit, implicit and automatic subincrementing schemes. In all cases, examples are included to illustrate the numerical characteristics of various methods that were considered.

University Transformation: New Demands and Coping Strategies

ERIC Educational Resources Information Center

Chidindi, Joseph

2012-01-01

University education system is undergoing transformation requirements particularly in the developing world. The demands require adaptation to the prevailing circumstances hence the need for relevant strategies for universities. Issues such as institutional profiles, organizational structure and work integration, research activities, and funding…

Linking the Pilot Structural Model and Pilot Workload

NASA Technical Reports Server (NTRS)

Bachelder, Edward; Hess, Ronald; Aponso, Bimal; Godfroy-Cooper, Martine

2018-01-01

Behavioral models are developed that closely reproduced pulsive control response of two pilots using markedly different control techniques while conducting a tracking task. An intriguing find was that the pilots appeared to: 1) produce a continuous, internally-generated stick signal that they integrated in time; 2) integrate the actual stick position; and 3) compare the two integrations to either issue or cease a pulse command. This suggests that the pilots utilized kinesthetic feedback in order to sense and integrate stick position, supporting the hypothesis that pilots can access and employ the proprioceptive inner feedback loop proposed by Hess's pilot Structural Model. A Pilot Cost Index was developed, whose elements include estimated workload, performance, and the degree to which the pilot employs kinesthetic feedback. Preliminary results suggest that a pilot's operating point (parameter values) may be based on control style and index minimization.

A Policy Paper on Applied Education.

ERIC Educational Resources Information Center

Murphy, Jerry

1992-01-01

Applied education, the integration of academic and vocational curricula, cannot supply the trained people needed by a rapidly changing society without sufficient planning and resources. Shortages of skilled workers are a societal issue requiring significant structural adjustment in the way skilled trades are managed. (JOW)

French Nuclear Forces,

DTIC Science & Technology

1984-05-05

integrated military structure of NATO. This paper briefly reviews French declaratory strategy, ex- plores France’s current and projected force structure, 2...major tendgn- cies in French foreign policy--independent, European, and Atlanticist--without forcing a choice between them. It per- mits France to... French politics, while they admit France m enjoys widespread agreement on defense issues, question the 0 C depth of the consensus. For example, Pierre

Steam generator tubes integrity: In-service-inspection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Comby, R.J.

1997-02-01

The author`s approach to tube integrity is in terms of looking for flaws in tubes. The basis for this approach is that no simple rules can be fixed to adopt a universal inspection methodology because of various concepts related to experience, leak acceptance, leak before break approach, etc. Flaw specific management is probably the most reliable approach as a compromise between safety, availability and economic issues. In that case, NDE capabilities have to be in accordance with information required by structural integrity demonstration. The author discusses the types of probes which can be used to search for flaws in additionmore » to the types of flaws which are being sought, with examples of specific analysis experiences. The author also discusses the issue of a reporting level as it relates to avoiding false calls, classifying faults, and allowing for automation in analysis.« less

Controlled data storage for non-volatile memory cells embedded in nano magnetic logic

NASA Astrophysics Data System (ADS)

Riente, Fabrizio; Ziemys, Grazvydas; Mattersdorfer, Clemens; Boche, Silke; Turvani, Giovanna; Raberg, Wolfgang; Luber, Sebastian; Breitkreutz-v. Gamm, Stephan

2017-05-01

Among the beyond-CMOS technologies, perpendicular Nano Magnetic Logic (pNML) is a promising candidate due to its low power consumption, its non-volatility and its monolithic 3D integrability, which makes it possible to integrate memory and logic into the same device by exploiting the interaction of bi-stable nanomagnets with perpendicular magnetic anisotropy. Logic computation and signal synchronization are achieved by focus ion beam irradiation and by pinning domain walls in magnetic notches. However, in realistic circuits, the information storage and their read-out are crucial issues, often ignored in the exploration of beyond-CMOS devices. In this paper we address these issues by experimentally demonstrating a pNML memory element, whose read and write operations can be controlled by two independent pulsed currents. Our results prove the correct behavior of the proposed structure that enables high density memory embedded in the logic plane of 3D-integrated pNML circuits.

The Journal of the Society for Accelerative Learning and Teaching, 1991.

ERIC Educational Resources Information Center

Journal of the Society for Accelerative Learning and Teaching, 1991

1991-01-01

The four issues of this journal published in 1991 contain the following articles: "Suggestology in the USSR"; "Integrated Short-term Intensive Course Structure; "Teaching Teachers to Teach"; "Sociopsychological Aspects of Intensive Teaching"; "The Method of Intensive Learning in the Context of Modern…

Values Transmission: Some Issues and an Idea.

ERIC Educational Resources Information Center

Shannon, Gary J.; Selinger, Alphonse D.

1980-01-01

The teaching of moral values should involve the building of considerable structure that can easily be integrated into the existing curriculum. This program would contain seven components: personalizing the environment, building community feeling, cooperative learning, developing awareness, encouraging self-respect and respect for others, and…

The aerodynamic effects of passing trains to surrounding objects and people

DOT National Transportation Integrated Search

2009-04-01

Two safety issues are raised on the aerodynamic effects of a passing train on its surroundings. First, a high-speed train passing other trains on an adjacent track exerts aerodynamic pressure that can affect the structural integrity of window mount a...

Information Structure, Information Technology, and the Human Services Organizational Environment.

ERIC Educational Resources Information Center

Semke, Jeanette I.; Nurius, Paula S.

1991-01-01

Examines current trends in data collection and information use in human services organizations. Describes issues for managers who are planning information systems, including practitioner resistance to automation. Proposes that conceptual integration of agendas for human services automation, practice evaluation, and service effectiveness enables…

[Digital signal processing of a novel neuron discharge model stimulation strategy for cochlear implants].

PubMed

Yang, Yiwei; Xu, Yuejin; Miu, Jichang; Zhou, Linghong; Xiao, Zhongju

2012-10-01

To apply the classic leakage integrate-and-fire models, based on the mechanism of the generation of physiological auditory stimulation, in the information processing coding of cochlear implants to improve the auditory result. The results of algorithm simulation in digital signal processor (DSP) were imported into Matlab for a comparative analysis. Compared with CIS coding, the algorithm of membrane potential integrate-and-fire (MPIF) allowed more natural pulse discharge in a pseudo-random manner to better fit the physiological structures. The MPIF algorithm can effectively solve the problem of the dynamic structure of the delivered auditory information sequence issued in the auditory center and allowed integration of the stimulating pulses and time coding to ensure the coherence and relevance of the stimulating pulse time.

Physical security and cyber security issues and human error prevention for 3D printed objects: detecting the use of an incorrect printing material

NASA Astrophysics Data System (ADS)

Straub, Jeremy

2017-06-01

A wide variety of characteristics of 3D printed objects have been linked to impaired structural integrity and use-efficacy. The printing material can also have a significant impact on the quality, utility and safety characteristics of a 3D printed object. Material issues can be created by vendor issues, physical security issues and human error. This paper presents and evaluates a system that can be used to detect incorrect material use in a 3D printer, using visible light imaging. Specifically, it assesses the ability to ascertain the difference between materials of different color and different types of material with similar coloration.

Centralized remote structural monitoring and management of real-time data

NASA Astrophysics Data System (ADS)

Han, Liting; Newhook, John P.; Mufti, Aftab A.

2004-07-01

Structural health monitoring (SHM) activities in civil engineering are increasing at a rapid pace in both research and field applications. This paper addresses the specific issue of incorporating internet technology into a structural health monitoring program. The issue of data volume versus communication speed is discussed along with a practical solution employed by ISIS Canada. The approach is illustrated through reference to several current case studies which include two bridges and a statue. It is seen that although the specifics of the projects and monitoring needs are different, the manner in which on-line monitoring can be conducted is very similar and easily allows for centralized monitoring. A general framework for website construction integrating sensing data and web camera options are presented. Issues related to simple real-time performance indices versus more comprehensive complex data analysis are discussed. Examples of on-line websites which allow visualization of new and historic data are presented. The paper also discusses future activities and research needs related to centralized remote structural monitoring and management of real-time data.

Integration of SrBi2Ta2O9 thin films for high density ferroelectric random access memory

NASA Astrophysics Data System (ADS)

Wouters, D. J.; Maes, D.; Goux, L.; Lisoni, J. G.; Paraschiv, V.; Johnson, J. A.; Schwitters, M.; Everaert, J.-L.; Boullart, W.; Schaekers, M.; Willegems, M.; Vander Meeren, H.; Haspeslagh, L.; Artoni, C.; Caputa, C.; Casella, P.; Corallo, G.; Russo, G.; Zambrano, R.; Monchoix, H.; Vecchio, G.; Van Autryve, L.

2006-09-01

Ferroelectric random access memory (FeRAM) is an attractive candidate technology for embedded nonvolatile memory, especially in applications where low power and high program speed are important. Market introduction of high-density FeRAM is, however, lagging behind standard complementary metal-oxide semiconductor (CMOS) because of the difficult integration technology. This paper discusses the major integration issues for high-density FeRAM, based on SrBi2Ta2O9 (strontium bismuth tantalate or SBT), in relation to the fabrication of our stacked cell structure. We have worked in the previous years on the development of SBT-FeRAM integration technology, based on a so-called pseudo-three-dimensional (3D) cell, with a capacitor that can be scaled from quasi two-dimensional towards a true three-dimensional capacitor where the sidewalls will importantly contribute to the signal. In the first phase of our integration development, we integrated our FeRAM cell in a 0.35μm CMOS technology. In a second phase, then, possibility of scaling of our cell is demonstrated in 0.18μm technology. The excellent electrical and reliability properties of the small integrated ferroelectric capacitors prove the feasibility of the technology, while the verification of the potential 3D effect confirms the basic scaling potential of our concept beyond that of the single-mask capacitor. The paper outlines the different material and technological challenges, and working solutions are demonstrated. While some issues are specific to our own cell, many are applicable to different stacked FeRAM cell concepts, or will become more general concerns when more developments are moving into 3D structures.

Indicators of Effective Policy Development & Implementation. Issue Brief #8

ERIC Educational Resources Information Center

Stonemeier, Jenny; Trader, Barb; Kaloi, Laura; Williams, Gabrielle

2016-01-01

Within the SWIFT framework, the Inclusive Policy Structure and Practice domain addresses the need for a supportive, reciprocal partnership between the school and its district or local educational agency. Therefore, intentional and effective policy decision-making processes are integral to SWIFT implementation. Such processes create opportunities…

Feminist and Family Systems Therapy: Are They Irreconcilable?

ERIC Educational Resources Information Center

Libow, Judith A.; And Others

1982-01-01

Urges more dialog between and integration of feminist and family systems theories in order to expand clinicians' flexibility and effectiveness. Considers points of conceptual and pragmatic convergence as well as divergence between the two perspectives. Highlights issues for development of a structural/strategic family systems model. (RC)

Aerospace safety advisory panel

NASA Technical Reports Server (NTRS)

1983-01-01

Data acquired on the actual flight experience with the various subsystems are assessed. These subsystems include: flight control and performance, structural integrity, orbiter landing gear, lithium batteries, EVA and prebreathing, and main engines. Improvements for routine operations are recommended. Policy issues for operations and flight safety for aircraft operations are discussed.

A self-diagnostic adhesive for monitoring bonded joints in aerospace structures

NASA Astrophysics Data System (ADS)

Zhuang, Yitao; Li, Yu-hung; Kopsaftopoulos, Fotis; Chang, Fu-Kuo

2016-04-01

Bondline integrity is still one of the most critical concerns in the design of aircraft structures up to date. Due to the lack of confidence on the integrity of the bondline both during fabrication and service, the industry standards and regulations still require assembling the composite using conventional fasteners. Furthermore, current state-of-the-art non-destructive evaluation (NDE) and structural health monitoring (SHM) techniques are incapable of offering mature solutions on the issue of bondline integrity monitoring. Therefore, the objective of this work is the development of an intelligent adhesive film with integrated micro-sensors for monitoring the integrity of the bondline interface. The proposed method makes use of an electromechanical-impedance (EMI) based method, which is a rapidly evolving approach within the SHM family. Furthermore, an innovative screen-printing technique to fabricate piezoelectric ceramic sensors with minimal thickness has been developed at Stanford. The approach presented in this study is based on the use of (i) micro screen-printed piezoelectric sensors integrated into adhesive leaving a minimal footprint on the material, (ii) numerical and analytical modeling of the EMI spectrum of the adhesive bondline, (iii) novel diagnostic algorithms for monitoring the bondline integrity based on advanced signal processing techniques, and (iv) the experimental assessment via prototype adhesively bonded structures in static (varying loads) and dynamic (fatigue) environments. The proposed method will provide a huge confidence on the use of bonded joints for aerospace structures and lead to a paradigm change in their design by enabling enormous weight savings while maximizing the economic and performance efficiency.

Structural issues affecting mixed methods studies in health research: a qualitative study.

PubMed

O'Cathain, Alicia; Nicholl, Jon; Murphy, Elizabeth

2009-12-09

Health researchers undertake studies which combine qualitative and quantitative methods. Little attention has been paid to the structural issues affecting this mixed methods approach. We explored the facilitators and barriers to undertaking mixed methods studies in health research. Face-to-face semi-structured interviews with 20 researchers experienced in mixed methods research in health in the United Kingdom. Structural facilitators for undertaking mixed methods studies included a perception that funding bodies promoted this approach, and the multidisciplinary constituency of some university departments. Structural barriers to exploiting the potential of these studies included a lack of education and training in mixed methods research, and a lack of templates for reporting mixed methods articles in peer-reviewed journals. The 'hierarchy of evidence' relating to effectiveness studies in health care research, with the randomised controlled trial as the gold standard, appeared to pervade the health research infrastructure. Thus integration of data and findings from qualitative and quantitative components of mixed methods studies, and dissemination of integrated outputs, tended to occur through serendipity and effort, further highlighting the presence of structural constraints. Researchers are agents who may also support current structures - journal reviewers and editors, and directors of postgraduate training courses - and thus have the ability to improve the structural support for exploiting the potential of mixed methods research. The environment for health research in the UK appears to be conducive to mixed methods research but not to exploiting the potential of this approach. Structural change, as well as change in researcher behaviour, will be necessary if researchers are to fully exploit the potential of using mixed methods research.

Simulation in Metallurgical Processing: Recent Developments and Future Perspectives

NASA Astrophysics Data System (ADS)

Ludwig, Andreas; Wu, Menghuai; Kharicha, Abdellah

2016-08-01

This article briefly addresses the most important topics concerning numerical simulation of metallurgical processes, namely, multiphase issues (particle and bubble motion and flotation/sedimentation of equiaxed crystals during solidification), multiphysics issues (electromagnetic stirring, electro-slag remelting, Cu-electro-refining, fluid-structure interaction, and mushy zone deformation), process simulations on graphical processing units, integrated computational materials engineering, and automatic optimization via simulation. The present state-of-the-art as well as requirements for future developments are presented and briefly discussed.

A Hybrid Numerical Analysis Method for Structural Health Monitoring

NASA Technical Reports Server (NTRS)

Forth, Scott C.; Staroselsky, Alexander

2001-01-01

A new hybrid surface-integral-finite-element numerical scheme has been developed to model a three-dimensional crack propagating through a thin, multi-layered coating. The finite element method was used to model the physical state of the coating (far field), and the surface integral method was used to model the fatigue crack growth. The two formulations are coupled through the need to satisfy boundary conditions on the crack surface and the external boundary. The coupling is sufficiently weak that the surface integral mesh of the crack surface and the finite element mesh of the uncracked volume can be set up independently. Thus when modeling crack growth, the finite element mesh can remain fixed for the duration of the simulation as the crack mesh is advanced. This method was implemented to evaluate the feasibility of fabricating a structural health monitoring system for real-time detection of surface cracks propagating in engine components. In this work, the authors formulate the hybrid surface-integral-finite-element method and discuss the mechanical issues of implementing a structural health monitoring system in an aircraft engine environment.

Aeroelastic modeling of rotor blades with spanwise variable elastic axis offset: Classic issues revisited and new formulations

NASA Technical Reports Server (NTRS)

Bielawa, Richard L.

1988-01-01

In response to a systematic methodology assessment program directed to the aeroelastic stability of hingeless helicopter rotor blades, improved basic aeroelastic reformulations and new formulations relating to structural sweep were achieved. Correlational results are presented showing the substantially improved performance of the G400 aeroelastic analysis incorporating these new formulations. The formulations pertain partly to sundry solutions to classic problem areas, relating to dynamic inflow with vortex-ring state operation and basic blade kinematics, but mostly to improved physical modeling of elastic axis offset (structural sweep) in the presence of nonlinear structural twist. Specific issues addressed are an alternate modeling of the delta EI torsional excitation due to compound bending using a force integration approach, and the detailed kinematic representation of an elastically deflected point mass of a beam with both structural sweep and nonlinear twist.

Systems Engineering and Integration for Technology Programs

NASA Technical Reports Server (NTRS)

Kennedy, Kruss J.

2006-01-01

The Architecture, Habitability & Integration group (AH&I) is a system engineering and integration test team within the NASA Crew and Thermal Systems Division (CTSD) at Johnson Space Center. AH&I identifies and resolves system-level integration issues within the research and technology development community. The timely resolution of these integration issues is fundamental to the development of human system requirements and exploration capability. The integration of the many individual components necessary to construct an artificial environment is difficult. The necessary interactions between individual components and systems must be approached in a piece-wise fashion to achieve repeatable results. A formal systems engineering (SE) approach to define, develop, and integrate quality systems within the life support community has been developed. This approach will allow a Research & Technology Program to systematically approach the development, management, and quality of technology deliverables to the various exploration missions. A tiered system engineering structure has been proposed to implement best systems engineering practices across all development levels from basic research to working assemblies. These practices will be implemented through a management plan across all applicable programs, projects, elements and teams. While many of the engineering practices are common to other industries, the implementation is specific to technology development. An accounting of the systems engineering management philosophy will be discussed and the associated programmatic processes will be presented.

Integrated inventory and monitoring

Treesearch

George Lightner; Hans T. Schreuder; Barry Bollenbacher; Kerry McMenus

2001-01-01

Understanding and inventorying our ecological systems is key to addressing how issues, questions, and management actions will affect the composition, structure, and function of these systems. Taking an ecological systems approach to the inventory and monitoring framework, is one which we feel will allow answers to currently identified management questions and new ones...

Challenges of Integrating Mobile Technology into Mathematics Instruction in Secondary Schools: An Indonesian Context

ERIC Educational Resources Information Center

Abidin, Zaenal; Mathrani, Anuradha; Hunter, Roberta; Parsons, David

2017-01-01

Implementing mobile learning in curriculum-based educational settings faces challenges related to perceived ethical and learning issues. This study investigated the affordances of mobile technologies to support mathematics instruction by teachers. An exploratory study employing questionnaires and semi-structured interviews revealed that, while…

Engineering Education as a Complex System

ERIC Educational Resources Information Center

Gattie, David K.; Kellam, Nadia N.; Schramski, John R.; Walther, Joachim

2011-01-01

This paper presents a theoretical basis for cultivating engineering education as a complex system that will prepare students to think critically and make decisions with regard to poorly understood, ill-structured issues. Integral to this theoretical basis is a solution space construct developed and presented as a benchmark for evaluating…

Cultural Lessons for Clinical Mental Health Practice: The Puyallup Tribal Community.

ERIC Educational Resources Information Center

Guilmet, George M.; Whited, David L.

1987-01-01

Discusses the integration of American Indian cultural perspectives within counseling and mental health services. Outlines several issues illustrating cultural lessons for clinical practices: family and social structure, ritual, cultural values and conflict, sense of time and self, communication styles, anger, and traditionalism. Contains 47…

77 FR 46935 - Airworthiness Directives; Airbus Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-07

...-0414; Directorate Identifier 2011-NM-210-AD; Amendment 39-17138; AD 2012-15-09] RIN 2120-AA64... calculated fatigue lives. This AD replaces certain slat extension eccentric bolts with new bolts. We are issuing this AD to prevent fatigue cracking, which could result in the loss of structural integrity of the...

78 FR 65166 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-31

... the upper deck tension ties of the fuselage are subject to widespread fatigue damage. We are issuing this AD to prevent widespread fatigue damage of certain fuselage upper deck tension ties, which could result in reduced structural integrity of the airplane. DATES: This AD is effective December 5, 2013. The...

Effects of Interdisciplinary Education on Technology-Driven Application Design

ERIC Educational Resources Information Center

Tafa, Z.; Rakocevic, G.; Mihailovic, D.; Milutinovic, V.

2011-01-01

This paper describes the structure and the underlying rationale of a new course dedicated to capability maturity model integration (CMMI)-directed design of wireless sensor networks (WSNs)-based biomedical applications that stresses: 1) engineering-, medico-engineering-, and informatics-related issues; 2) design for general- and special-purpose…

Contradictory or Complementary? Reassessment of Two Competing Theories of the Structure of Attitudes.

ERIC Educational Resources Information Center

Birenbaum, Menucha; Zak, Itai

1982-01-01

The theories of Kerlinger and Eysenck on the nature of the dimensions underlying social attitudes are discussed. Integrating principles from both theories, an alternative approach to the issue, is suggested and tested on the domain of attitudes toward education in relation to personality. (Author/JKS)

Personal-Academic Studies Engage Urban, Seventh-Grade Students

ERIC Educational Resources Information Center

Hansen, Jane

2014-01-01

A successful middle school team of teachers employed effective middle level philosophy to structure a curriculum around themes that were relevant, challenging, integrative, and engaging for their particular students and community. Realizing that their young adolescents were involved in tough, delicate issues in their out-of-school lives, the…

AN INTEGRATED PERSPECTIVE ON THE ASSESSMENT OF TECHNOLOGIES: INTEGRATE-HTA.

PubMed

Wahlster, Philip; Brereton, Louise; Burns, Jacob; Hofmann, Björn; Mozygemba, Kati; Oortwijn, Wija; Pfadenhauer, Lisa; Polus, Stephanie; Rehfuess, Eva; Schilling, Imke; van der Wilt, Gert Jan; Gerhardus, Ansgar

2017-01-01

Current health technology assessment (HTA) is not well equipped to assess complex technologies as insufficient attention is being paid to the diversity in patient characteristics and preferences, context, and implementation. Strategies to integrate these and several other aspects, such as ethical considerations, in a comprehensive assessment are missing. The aim of the European research project INTEGRATE-HTA was to develop a model for an integrated HTA of complex technologies. A multi-method, four-stage approach guided the development of the INTEGRATE-HTA Model: (i) definition of the different dimensions of information to be integrated, (ii) literature review of existing methods for integration, (iii) adjustment of concepts and methods for assessing distinct aspects of complex technologies in the frame of an integrated process, and (iv) application of the model in a case study and subsequent revisions. The INTEGRATE-HTA Model consists of five steps, each involving stakeholders: (i) definition of the technology and the objective of the HTA; (ii) development of a logic model to provide a structured overview of the technology and the system in which it is embedded; (iii) evidence assessment on effectiveness, economic, ethical, legal, and socio-cultural aspects, taking variability of participants, context, implementation issues, and their interactions into account; (iv) populating the logic model with the data generated in step 3; (v) structured process of decision-making. The INTEGRATE-HTA Model provides a structured process for integrated HTAs of complex technologies. Stakeholder involvement in all steps is essential as a means of ensuring relevance and meaningful interpretation of the evidence.

A literature review on integrated perinatal care

PubMed Central

Rodríguez, Charo; des Rivières-Pigeon, Catherine

2007-01-01

Context The perinatal period is one during which health care services are in high demand. Like other health care sub-sectors, perinatal health care delivery has undergone significant changes in recent years, such as the integrative wave that has swept through the health care industry since the early 1990s. Purpose The present study aims at reviewing scholarly work on integrated perinatal care to provide support for policy decision-making. Results Researchers interested in integrated perinatal care have, by assessing the effectiveness of individual clinical practices and intervention programs, mainly addressed issues of continuity of care and clinical and professional integration. Conclusions Improvements in perinatal health care delivery appear related not to structurally integrated health care delivery systems, but to organizing modalities that aim to support woman-centred care and cooperative clinical practice. PMID:17786177

Introduction: The challenge of optimum integration of propulsion systems and large space structures

NASA Technical Reports Server (NTRS)

Carlisle, R. F.

1980-01-01

A functional matrix of possible propulsion system characteristics for a spacecraft for deployable and assembled spacecraft structures shows that either electric propulsion or low thrust chemical propulsion systems could provide the propulsion required. The trade-off considerations of a single propulsion engine or multiengines are outlined and it is shown that a single point engine is bounded by some upper limit of thrust for assembled spacecraft. The matrix also shows several additional functions that can be provided to the spacecraft if a propulsion system is an integral part of the spacecraft. A review of all of the functions that can be provided for a spacecraft by an integral propulsion system may result in the inclusion of the propulsion for several functions even if no single function were mandatory. Propulsion interface issues for each combination of engines are identified.

Methodologies for Combined Loads Tests Using a Multi-Actuator Test Machine

NASA Technical Reports Server (NTRS)

Rouse, Marshall

2013-01-01

The NASA Langley COmbined Loads Test System (COLTS) Facility was designed to accommodate a range of fuselage structures and wing sections and subject them to both quasistatic and cyclic loading conditions. Structural tests have been conducted in COLTS that address structural integrity issues of metallic and fiber reinforced composite aerospace structures in support of NASA Programs (i.e. the Aircraft Structural Integrity (ASIP) Program, High-Speed-Research program and the Supersonic Project, NASA Engineering and Safety Center (NESC) Composite Crew Module Project, and the Environmentally Responsible Aviation Program),. This paper presents experimental results for curved panels subjected to mechanical and internal pressure loads using a D-box test fixture. Also, results are presented that describe use of a checkout beam for development of testing procedures for a combined mechanical and pressure loading test of a Multi-bay box. The Multi-bay box test will be used to experimentally verify the structural performance of the Multi-bay box in support of the Environmentally Responsible Aviation Project at NASA Langley.

Community structural characteristics and the adoption of fluoridation.

PubMed Central

Smith, R A

1981-01-01

A study of community structural characteristics associated with fluoridation outcomes was conducted in 47 communities. A three-part outcome distinction was utilized: communities never having publicly considered the fluoridation issue, those rejecting it, and those accepting it. The independent variables reflect the complexity of the community social and economic structure, social integration, and the centralization of authority. Results of mean comparisons show statistically significant differences between the three outcome types on the independent variables. A series of discriminant analyses provides furtheor evidence of how the independent variables are associated with each outcome type. Non-considering communities are shown to be low in complexity, and high in social integration and the centralization of governmental authority. Rejecters are shown to be high in complexity, but low in social integration and centralized authority. Adopters are relatively high on all three sets of variables. Theretical reasoning is provided to support the hypothesis and why these results are expected. The utility of these results and structural explanations in general are discussed, especially for public/environmental health planning and political activities. PMID:7258427

A finite element: Boundary integral method for electromagnetic scattering. Ph.D. Thesis Technical Report, Feb. - Sep. 1992

NASA Technical Reports Server (NTRS)

Collins, J. D.; Volakis, John L.

1992-01-01

A method that combines the finite element and boundary integral techniques for the numerical solution of electromagnetic scattering problems is presented. The finite element method is well known for requiring a low order storage and for its capability to model inhomogeneous structures. Of particular emphasis in this work is the reduction of the storage requirement by terminating the finite element mesh on a boundary in a fashion which renders the boundary integrals in convolutional form. The fast Fourier transform is then used to evaluate these integrals in a conjugate gradient solver, without a need to generate the actual matrix. This method has a marked advantage over traditional integral equation approaches with respect to the storage requirement of highly inhomogeneous structures. Rectangular, circular, and ogival mesh termination boundaries are examined for two-dimensional scattering. In the case of axially symmetric structures, the boundary integral matrix storage is reduced by exploiting matrix symmetries and solving the resulting system via the conjugate gradient method. In each case several results are presented for various scatterers aimed at validating the method and providing an assessment of its capabilities. Important in methods incorporating boundary integral equations is the issue of internal resonance. A method is implemented for their removal, and is shown to be effective in the two-dimensional and three-dimensional applications.

Differing Perceptions Concerning Research Integrity Between Universities and Industry: A Qualitative Study.

PubMed

Godecharle, Simon; Nemery, Benoit; Dierickx, Kris

2017-09-14

Despite the ever increasing collaboration between industry and universities, the previous empirical studies on research integrity and misconduct excluded participants of biomedical industry. Hence, there is a lack of empirical data on how research managers and biomedical researchers active in industry perceive the issues of research integrity and misconduct, and whether or not their perspectives differ from those of researchers and research managers active in universities. If various standards concerning research integrity and misconduct are upheld between industry and universities, this might undermine research collaborations. Therefore we performed a qualitative study by conducting 22 semi-structured interviews in order to investigate and compare the perspectives and attitudes concerning the issues of research integrity and misconduct of research managers and biomedical researchers active in industry and universities. Our study showed clear discrepancies between both groups. Diverse strategies in order to manage research misconduct and to stimulate research integrity were observed. Different definitions of research misconduct were given, indicating that similar actions are judged heterogeneously. There were also differences at an individual level, whether the interviewees were active in industry or universities. Overall, the management of research integrity proves to be a difficult exercise, due to many diverse perspectives on several essential elements connected to research integrity and misconduct. A management policy that is not in line with the vision of the biomedical researchers and research managers is at risk of being inefficient.

Institutional ethics review of clinical study agreements

PubMed Central

DuVal, G

2004-01-01

Accordingly, it is necessary that some independent body have the authority both to review research contracts for compliance with norms of subject protection and ethical integrity, and to reject studies that fail to meet ethical standards. Such review should take place prior to the start of research, not later. Because of its expertise and authority, the institutional ethics review board (IRB or REB) is the appropriate body to undertake such review. Much recent commentary has focused on contractual restrictions on the investigator's freedom to publish research findings. The Olivieri experience, and that of other investigators, has brought freedom of publication issues into sharp focus. Clinical study agreements also raise a number of other ethical issues relating to human subjects and research integrity, however, including disclosures relating to patient safety, data analysis and reporting, budget, confidentiality, and premature termination of the study. This paper describes the ethical issues at stake in structuring such agreements and suggests ethical standards to guide institutional ethics review. PMID:14872068

Autonomous Assembly of Modular Structures in Space and on Extraterrestrial Locations

NASA Astrophysics Data System (ADS)

Alhorn, Dean C.

2005-02-01

The new U.S. National Vision for Space Exploration requires many new enabling technologies to accomplish the goals of space commercialization and returning humans to the moon and extraterrestrial environments. Traditionally, flight elements are complete sub-systems requiring humans to complete the integration and assembly. These bulky structures also require the use of heavy launch vehicles to send the units to a desired location. This philosophy necessitates a high degree of safety, numerous space walks at a significant cost. Future space mission costs must be reduced and safety increased to reasonably achieve exploration goals. One proposed concept is the autonomous assembly of space structures. This concept is an affordable, reliable solution to in-space and extraterrestrial assembly. Assembly is autonomously performed when two components join after determining that specifications are correct. Local sensors continue monitor joint integrity post assembly, which is critical for safety and structural reliability. Achieving this concept requires a change in space structure design philosophy and the development of innovative technologies to perform autonomous assembly. Assembly of large space structures will require significant numbers of integrity sensors. Thus simple, low-cost sensors are integral to the success of this concept. This paper addresses these issues and proposes a novel concept for assembling space structures autonomously. Core technologies required to achieve in space assembly are presented. These core technologies are critical to the goal of utilizing space in a cost efficient and safe manner. Additionally, these novel technologies can be applied to other systems both on earth and extraterrestrial environments.

Autonomous Assembly of Modular Structures in Space and on Extraterrestrial Locations

NASA Technical Reports Server (NTRS)

Alhorn, Dean C.

2005-01-01

The new U.S. National Vision for Space Exploration requires many new enabling technologies to accomplish the goals of space commercialization and returning humans to the moon and extraterrestrial environments. Traditionally, flight elements are complete subsystems requiring humans to complete the integration and assembly. These bulky structures also require the use of heavy launch vehicles to send the units to a desired location. This philosophy necessitates a high degree of safety, numerous space walks at a significant cost. Future space mission costs must be reduced and safety increased to reasonably achieve exploration goals. One proposed concept is the autonomous assembly of space structures. This concept is an affordable, reliable solution to in-space and extraterrestrial assembly. Assembly is autonomously performed when two components join after determining that specifications are correct. Local sensors continue monitor joint integrity post assembly, which is critical for safety and structural reliability. Achieving this concept requires a change in space structure design philosophy and the development of innovative technologies to perform autonomous assembly. Assembly of large space structures will require significant numbers of integrity sensors. Thus simple, low-cost sensors are integral to the success of this concept. This paper addresses these issues and proposes a novel concept for assembling space structures autonomously. Core technologies required to achieve in space assembly are presented. These core technologies are critical to the goal of utilizing space in a cost efficient and safe manner. Additionally, these novel technologies can be applied to other systems both on earth and extraterrestrial environments.

An artificial intelligence-based structural health monitoring system for aging aircraft

NASA Technical Reports Server (NTRS)

Grady, Joseph E.; Tang, Stanley S.; Chen, K. L.

1993-01-01

To reduce operating expenses, airlines are now using the existing fleets of commercial aircraft well beyond their originally anticipated service lives. The repair and maintenance of these 'aging aircraft' has therefore become a critical safety issue, both to the airlines and the Federal Aviation Administration. This paper presents the results of an innovative research program to develop a structural monitoring system that will be used to evaluate the integrity of in-service aerospace structural components. Currently in the final phase of its development, this monitoring system will indicate when repair or maintenance of a damaged structural component is necessary.

Structural issues affecting mixed methods studies in health research: a qualitative study

PubMed Central

2009-01-01

Background Health researchers undertake studies which combine qualitative and quantitative methods. Little attention has been paid to the structural issues affecting this mixed methods approach. We explored the facilitators and barriers to undertaking mixed methods studies in health research. Methods Face-to-face semi-structured interviews with 20 researchers experienced in mixed methods research in health in the United Kingdom. Results Structural facilitators for undertaking mixed methods studies included a perception that funding bodies promoted this approach, and the multidisciplinary constituency of some university departments. Structural barriers to exploiting the potential of these studies included a lack of education and training in mixed methods research, and a lack of templates for reporting mixed methods articles in peer-reviewed journals. The 'hierarchy of evidence' relating to effectiveness studies in health care research, with the randomised controlled trial as the gold standard, appeared to pervade the health research infrastructure. Thus integration of data and findings from qualitative and quantitative components of mixed methods studies, and dissemination of integrated outputs, tended to occur through serendipity and effort, further highlighting the presence of structural constraints. Researchers are agents who may also support current structures - journal reviewers and editors, and directors of postgraduate training courses - and thus have the ability to improve the structural support for exploiting the potential of mixed methods research. Conclusion The environment for health research in the UK appears to be conducive to mixed methods research but not to exploiting the potential of this approach. Structural change, as well as change in researcher behaviour, will be necessary if researchers are to fully exploit the potential of using mixed methods research. PMID:20003210

Integrated Business Process Adaptation towards Friction-Free Business-to-Business Collaboration

ERIC Educational Resources Information Center

Shan, Zhe

2011-01-01

One key issue in process-aware E-commerce collaboration is the orchestration of business processes of multiple business partners throughout a supply chain network in an automated and seamless way. Since each partner has its own internal processes with different control flow structures and message interfaces, the real challenge lies in verifying…

Revising Community College Bylaws to Protect Institutional Integrity: Process and Product.

ERIC Educational Resources Information Center

Katsinas, Stephen G.; And Others

1988-01-01

Describes the Board of Directors' of the Miami-Dade Community College Foundation development of new bylaws. Provides information on the foundation's structure and functions, the concern of the Ad Hoc Committee on Governance with the issues of quorum and board member oversight, and the responsibilities of the foundation's committees. (DMM)

Delivering an Alternative Medicine Resource to the User's Desktop via World Wide Web.

ERIC Educational Resources Information Center

Li, Jie; Wu, Gang; Marks, Ellen; Fan, Weiyu

1998-01-01

Discusses the design and implementation of a World Wide Web-based alternative medicine virtual resource. This homepage integrates regional, national, and international resources and delivers library services to the user's desktop. Goals, structure, and organizational schemes of the system are detailed, and design issues for building such a…

Understanding Innovation: Youth-Adult Partnerships in Decision Making

ERIC Educational Resources Information Center

Zeldin, Shepherd; Petrokubi, Julie

2006-01-01

In the United States, the concept of youth-adult partnership remains innovative. The notion that youth and adults can collaborate on issues of importance runs counter to prevailing societal norms, public policies, structures and standards of practice. There is not much cultural or policy support for managers seeking to integrate youth-adult…

The Intellectual Structure of Metacognitive Scaffolding in Science Education: A Co-Citation Network Analysis

ERIC Educational Resources Information Center

Tang, Kai-Yu; Wang, Chia-Yu; Chang, Hsin-Yi; Chen, Sufen; Lo, Hao-Chang; Tsai, Chin-Chung

2016-01-01

The issues of metacognitive scaffolding in science education (MSiSE) have become increasingly popular and important. Differing from previous content reviews, this study proposes a series of quantitative computer-based analyses by integrating document co-citation analysis, social network analysis, and exploratory factor analysis to explore the…

Responses and Clarifications regarding Science and Worldviews

ERIC Educational Resources Information Center

Gauch, Hugh G., Jr.

2009-01-01

This article responds to the other 10 papers in this thematic issue on science and worldviews and it clarifies some of the points in my lead article. The Bayesian framework provides helpful structure for worldview inquiries by recognizing and integrating both public and personal evidence. Drawing upon the other 10 papers, six kinds of potential…

Engineering education as a complex system

NASA Astrophysics Data System (ADS)

Gattie, David K.; Kellam, Nadia N.; Schramski, John R.; Walther, Joachim

2011-12-01

This paper presents a theoretical basis for cultivating engineering education as a complex system that will prepare students to think critically and make decisions with regard to poorly understood, ill-structured issues. Integral to this theoretical basis is a solution space construct developed and presented as a benchmark for evaluating problem-solving orientations that emerge within students' thinking as they progress through an engineering curriculum. It is proposed that the traditional engineering education model, while analytically rigorous, is characterised by properties that, although necessary, are insufficient for preparing students to address complex issues of the twenty-first century. A Synthesis and Design Studio model for engineering education is proposed, which maintains the necessary rigor of analysis within a uniquely complex yet sufficiently structured learning environment.

Practical Application of Sociology in Systems Engineering

NASA Technical Reports Server (NTRS)

Watson, Michael D.; Andrews, James G.; Eckley, Jeri Cassel; Culver, Michael L.

2017-01-01

Systems engineering involves both the integration of the system and the integration of the disciplines which develop and operate the system. Integrating the disciplines is a sociological effort to bring together different groups, who often have different terminology, to achieve a common goal, the system. The focus for the systems engineer is information flow through the organization, between the disciplines, to ensure the system is developed and operated will all relevant information informing system decisions. The practical application of the sociology in systems engineering brings in various organizational development concepts including the principles of planned renegotiation and the application of principles to address information barriers created by organizational culture. Concepts such as specification of ignorance, consistent terminology, opportunity structures, role-sets, and the reclama (reconsideration) process are all important sociological approaches that help address the organizational social structure (culture). In bringing the disciplines together, the systems engineer must also be wary of social ambivalence, social anomie, social dysfunction, and insider-outsider behavior. Unintended consequences can result when these social issues are present. These issues can occur when localized subcultures shift from the overarching organizational culture, or when the organizational culture prevents achievement of system goals. These sociological principles provide the systems engineer with key approaches to manage the information flow through the organization as the disciplines are integrated and share their information and provides key sociological barriers to information flow through the organization. This paper will discuss the practical application of sociological principles to systems engineering.

A comparative study of serial and parallel aeroelastic computations of wings

NASA Technical Reports Server (NTRS)

Byun, Chansup; Guruswamy, Guru P.

1994-01-01

A procedure for computing the aeroelasticity of wings on parallel multiple-instruction, multiple-data (MIMD) computers is presented. In this procedure, fluids are modeled using Euler equations, and structures are modeled using modal or finite element equations. The procedure is designed in such a way that each discipline can be developed and maintained independently by using a domain decomposition approach. In the present parallel procedure, each computational domain is scalable. A parallel integration scheme is used to compute aeroelastic responses by solving fluid and structural equations concurrently. The computational efficiency issues of parallel integration of both fluid and structural equations are investigated in detail. This approach, which reduces the total computational time by a factor of almost 2, is demonstrated for a typical aeroelastic wing by using various numbers of processors on the Intel iPSC/860.

An integrated health and social care organisation in Sweden: creation and structure of a unique local public health and social care system.

PubMed

Øvretveit, John; Hansson, Johan; Brommels, Mats

2010-10-01

Research and citizens have noted failures in coordinating health and social services and professionals, and the need to address this issue to realize benefits from increasing specialisation. Different methods have been proposed and one has been structural integration of separate services within one organisation. This paper reports an empirical longitudinal study of the development of an integrated health and social care organisation in Sweden combining service provision, purchasing and political governance for a defined population. The study found a combination of influences contributed to the development of this new organisation. The initial structural macro-integration facilitated, but did not of itself result in better clinical care coordination. Other actions were needed to modify the specialised systems and cultures which the organisation inherited. The study design was not able to establish with any degree of certainty whether better patient and cost outcomes resulted, but it did find structural and process changes which make improved outcomes likely. The study concludes that coordinated actions at different levels and of different types were needed to achieve care coordination for patients and that a phased approach was necessary where management capacity and outside expertise are limited. Copyright (c) 2010 Elsevier Ireland Ltd. All rights reserved.

Reflecting on the structure of soil classification systems: insights from a proposal for integrating subsoil data into soil information systems

NASA Astrophysics Data System (ADS)

Dondeyne, Stefaan; Juilleret, Jérôme; Vancampenhout, Karen; Deckers, Jozef; Hissler, Christophe

2017-04-01

Classification of soils in both World Reference Base for soil resources (WRB) and Soil Taxonomy hinges on the identification of diagnostic horizons and characteristics. However as these features often occur within the first 100 cm, these classification systems convey little information on subsoil characteristics. An integrated knowledge of the soil, soil-to-substratum and deeper substratum continuum is required when dealing with environmental issues such as vegetation ecology, water quality or the Critical Zone in general. Therefore, we recently proposed a classification system of the subsolum complementing current soil classification systems. By reflecting on the structure of the subsoil classification system which is inspired by WRB, we aim at fostering a discussion on some potential future developments of WRB. For classifying the subsolum we define Regolite, Saprolite, Saprock and Bedrock as four Subsolum Reference Groups each corresponding to different weathering stages of the subsoil. Principal qualifiers can be used to categorize intergrades of these Subsoil Reference Groups while morphologic and lithologic characteristics can be presented with supplementary qualifiers. We argue that adopting a low hierarchical structure - akin to WRB and in contrast to a strong hierarchical structure as in Soil Taxonomy - offers the advantage of having an open classification system avoiding the need for a priori knowledge of all possible combinations which may be encountered in the field. Just as in WRB we also propose to use principal and supplementary qualifiers as a second level of classification. However, in contrast to WRB we propose to reserve the principal qualifiers for intergrades and to regroup the supplementary qualifiers into thematic categories (morphologic or lithologic). Structuring the qualifiers in this manner should facilitate the integration and handling of both soil and subsoil classification units into soil information systems and calls for paying attention to these structural issues in future developments of WRB.

Very high speed integrated circuits - Into the second generation. V - The issues of standardization and technology insertion

NASA Astrophysics Data System (ADS)

Martin, J.

1982-04-01

It is shown that the fulfillment of very high speed integrated circuit (VHSIC) device development goals entails the restructuring of military electronics acquisition policy, standardization which produces the maximum number of systems and subsystems by means of the minimum number of flexible, broad-purpose, high-power semiconductors, and especially the standardization of bus structures incorporating a priorization system. It is expected that the Design Specification Handbook currently under preparation by the VHSIC program office of the DOD will make the design of such systems a task whose complexity is comparable to that of present integrated circuit electronics.

Extending software repository hosting to code review and testing

NASA Astrophysics Data System (ADS)

Gonzalez Alvarez, A.; Aparicio Cotarelo, B.; Lossent, A.; Andersen, T.; Trzcinska, A.; Asbury, D.; Hłimyr, N.; Meinhard, H.

2015-12-01

We will describe how CERN's services around Issue Tracking and Version Control have evolved, and what the plans for the future are. We will describe the services main design, integration and structure, giving special attention to the new requirements from the community of users in terms of collaboration and integration tools and how we address this challenge when defining new services based on GitLab for collaboration to replace our current Gitolite service and Code Review and Jenkins for Continuous Integration. These new services complement the existing ones to create a new global "development tool stack" where each working group can place its particular development work-flow.

[Integral care, a SUS (Brazilian Unified Health System) guideline for the sanitary surveillance].

PubMed

O'Dwyer, Gisele; Reis, Daniela Carla de Souza; da Silva, Luciana Leite Gonçalves

2010-11-01

The sanitary surveillance (Visa) performs several practices, on different objects and its actions are guided by principles and guidelines of the SUS. It was done a critical reflection on the interaction conditions of practice in Visa, with a constitutional proposition of the SUS: integral care. The analysis was based on the theory of structuration (Giddens) that considers mobilization of structural resources as dimensions of social interaction, which would justify the legitimacy exercised since the standards. Have been analyzed the following categories: Visa and its insertion within the SUS; the integral care and the Visa; and political impediments. The Visa has been organized by National Health Surveillance Agency. Nowadays it has as sanitary responsibilities, communication with society and health promotion. The proposal of the literature concerning integral care is based on the assistance issue. The organization of the services in the different federative entities is the sense of integral care most adopted by Visa. Political impediments focus on the institutional renewal, on the conflicts of interest arena, on the distance between formulated policies and established practices and gaps concerning work management and the insufficiency of financial support.

Topics in LIFE Target Survival: 11-SI-004 Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miles, Robin; Benett, Bill; Bond, Tiziana

The LIFE target design incorporates many considerations to generate the desired fusion gain including the physics design, the cost of manufacturing of the target, the injectability of the target, the aerodynamic flight characteristics of the target, the ability to track and engage the target and to maintain the structural and thermal integrity of the target. This document describes the effort that was made in support of issues of survivability of the target during injection which included issues massmanufactural materials and processes which could be used in the target.

Sustainable Sourcing of Global Agricultural Raw Materials: Assessing Gaps in Key Impact and Vulnerability Issues and Indicators

PubMed Central

Springer, Nathaniel P.; Garbach, Kelly; Guillozet, Kathleen; Haden, Van R.; Hedao, Prashant; Hollander, Allan D.; Huber, Patrick R.; Ingersoll, Christina; Langner, Megan; Lipari, Genevieve; Mohammadi, Yaser; Musker, Ruthie; Piatto, Marina; Riggle, Courtney; Schweisguth, Melissa; Sin, Emily; Snider, Sara; Vidic, Nataša; White, Aubrey; Brodt, Sonja; Quinn, James F.; Tomich, Thomas P.

2015-01-01

Understanding how to source agricultural raw materials sustainably is challenging in today’s globalized food system given the variety of issues to be considered and the multitude of suggested indicators for representing these issues. Furthermore, stakeholders in the global food system both impact these issues and are themselves vulnerable to these issues, an important duality that is often implied but not explicitly described. The attention given to these issues and conceptual frameworks varies greatly—depending largely on the stakeholder perspective—as does the set of indicators developed to measure them. To better structure these complex relationships and assess any gaps, we collate a comprehensive list of sustainability issues and a database of sustainability indicators to represent them. To assure a breadth of inclusion, the issues are pulled from the following three perspectives: major global sustainability assessments, sustainability communications from global food companies, and conceptual frameworks of sustainable livelihoods from academic publications. These terms are integrated across perspectives using a common vocabulary, classified by their relevance to impacts and vulnerabilities, and categorized into groups by economic, environmental, physical, human, social, and political characteristics. These issues are then associated with over 2,000 sustainability indicators gathered from existing sources. A gap analysis is then performed to determine if particular issues and issue groups are over or underrepresented. This process results in 44 “integrated” issues—24 impact issues and 36 vulnerability issues —that are composed of 318 “component” issues. The gap analysis shows that although every integrated issue is mentioned at least 40% of the time across perspectives, no issue is mentioned more than 70% of the time. A few issues infrequently mentioned across perspectives also have relatively few indicators available to fully represent them. Issues in the impact framework generally have fewer gaps than those in the vulnerability framework. PMID:26065899

CALL FOR PAPERS: Special issue on Symmetries and Integrability of Difference Equations

NASA Astrophysics Data System (ADS)

Doliwa, Adam; Korhonen, Risto; Lafortune, Stephane

2006-10-01

This is a call for contributions to a special issue of Journal of Physics A: Mathematical and General entitled `Special issue on Symmetries and Integrability of Difference Equations' as featured at the SIDE VII meeting held during July 2006 in Melbourne (http://web.maths.unsw.edu.au/%7Eschief/side/side.html). Participants at that meeting, as well as other researchers working in the field of difference equations and discrete systems, are invited to submit a research paper to this issue. This meeting was the seventh of a series of biennial meetings devoted to the study of integrable difference equations and related topics. The notion of integrability was first introduced in the 19th century in the context of classical mechanics with the definition of Liouville integrability for Hamiltonian flows. Since then, several notions of integrability have been introduced for partial and ordinary differential equations. Closely related to integrability theory is the symmetry analysis of nonlinear evolution equations. Symmetry analysis takes advantage of the Lie group structure of a given equation to study its properties. Together, integrability theory and symmetry analysis provide the main method by which nonlinear evolution equations can be solved explicitly. Difference equations, just as differential equations, are important in numerous fields of science and have a wide variety of applications in such areas as: mathematical physics, computer visualization, numerical analysis, mathematical biology, economics, combinatorics, quantum field theory, etc. It is thus crucial to develop tools to study and solve difference equations. While the theory of symmetry and integrability for differential equations is now well-established, this is not yet the case for discrete equations. The situation has undergone impressive development in recent years and has affected a broad range of fields, including the theory of special functions, quantum integrable systems, numerical analysis, cellular automata, representations of quantum groups, symmetries of difference equations, discrete (difference) geometry, etc. Consequently, the aim of the special issue is to benefit from the occasion offered by the SIDE VII meeting to provide a collection of papers which represent the state-of-the-art knowledge for studying integrability and symmetry properties of difference equations. Scope of the special issue The special issue will feature papers which deal with themes that were covered by the SIDE VII Conference. These are •Integrability testing •Discrete geometry and visualization •Laurent phenomena and cluster algebras •Ultra-discrete systems •Random matrix theory •Algebraic-geometric approaches to integrability •Yang-Baxter equations •Quantum and classical integrable systems •Difference Galois theory Editorial policy •The subject of the paper should relate to the subject of the meeting. The Guest Editors will reserve the right to judge whether a contribution fits the scope of the topic of the special issue. •Contributions will be refereed and processed according to the usual procedure of the journal. •Conference papers may be based on already published work but should either •contain significant additional new results and/or insights or •give a survey of the present state of the art, a critical assessment of the present understanding of a topic, and a discussion of open problems. •Papers submitted by non-participants should be original and contain substantial new results. Guidelines for preparation of contributions • The deadline for contributed papers will be 15 January 2007. •There is a page limit of 16 printed pages (approximately 9600 words) per contribution. For submitted papers exceeding this length the Guest Editors reserve the right to request a reduction in length. Further advice on document preparation can be found at www.iop.org/Journals/jphysa •Contributions to the special issue should if possible be submitted electronically by web upload at www.iop.org/Journals/jphysa, or by email to jphysa@iop.org, quoting 'J. Phys. A Special Issue: SIDE VII'. Submissions should ideally be in standard LaTeX form; we are, however, able to accept most formats including Microsoft Word. Please see the website for further information on electronic submissions. •Authors unable to submit electronically may send hard-copy contributions to: Publishing Administrators, Journal of Physics A, Institute of Physics Publishing, Dirac House, Temple Back, Bristol BS1 6BE, UK, enclosing electronic code on floppy disk if available and quoting 'J. Phys. A Special Issue: SIDE VII'. • All contributions should be accompanied by a read-me file or covering letter giving the postal and email address for correspondence. The Publishing Office should be notified of any subsequent change of address. •The special issue will be published in the paper and online version of the journal. The corresponding author of each contribution will receive a complimentary copy of the issue.

The Role of Integrated Modelling and Assessment for Decision-Making: Lessons from Water Allocation Issues in Australia

NASA Astrophysics Data System (ADS)

Jakeman, A. J.; Guillaume, J. H. A.; El Sawah, S.; Hamilton, S.

2014-12-01

Integrated modelling and assessment (IMA) is best regarded as a process that can support environmental decision-making when issues are strongly contested and uncertainties pervasive. To be most useful, the process must be multi-dimensional and phased. Principally, it must be tailored to the problem context to encompass diverse issues of concern, management settings and stakeholders. This in turn requires the integration of multiple processes and components of natural and human systems and their corresponding spatial and temporal scales. Modellers therefore need to be able to integrate multiple disciplines, methods, models, tools and data, and many sources and types of uncertainty. These dimensions are incorporated into iteration between the various phases of the IMA process, including scoping, problem framing and formulation, assessing options and communicating findings. Two case studies in Australia are employed to share the lessons of how integration can be achieved in these IMA phases using a mix of stakeholder participation processes and modelling tools. One case study aims to improve the relevance of modelling by incorporating stakeholder's views of irrigated viticulture and water management decision making. It used a novel methodology with the acronym ICTAM, consisting of Interviews to elicit mental models, Cognitive maps to represent and analyse individual and group mental models, Time-sequence diagrams to chronologically structure the decision making process, an All-encompassing conceptual model, and computational Models of stakeholder decision making. The second case uses a hydro-economic river network model to examine basin-wide impacts of water allocation cuts and adoption of farm innovations. The knowledge exchange approach used in each case was designed to integrate data and knowledge bearing in mind the contextual dimensions of the problem at hand, and the specific contributions that environmental modelling was thought to be able to make.

Total quality through computer integrated manufacturing in the pharmaceutical industry.

PubMed

Ufret, C M

1995-01-01

The role of Computer Integrated Manufacturing (CIM) in the pursue of total quality in pharmaceutical manufacturing is assessed. CIM key objectives, design criteria, and performance measurements, in addition to its scope and implementation in a hierarchical structure, are explored in detail. Key elements for the success of each phase in a CIM project and a brief status of current CIM implementations in the pharmaceutical industry are presented. The role of World Class Manufacturing performance standards and other key issues to achieve full CIM benefits are also addressed.

Selected issues of the universal communication environment implementation for CII standard

NASA Astrophysics Data System (ADS)

Zagoździńska, Agnieszka; Poźniak, Krzysztof T.; Drabik, Paweł K.

2011-10-01

In the contemporary FPGA market there is the wide assortment of structures, integrated development environments, and boards of different producers. The variety allows to fit resources to requirements of the individual designer. There is the need of standardization of the projects to make it useful in research laboratories equipped with different producers tools. Proposed solution is CII standardization of VHDL components. This paper contains specification of the universal communication environment for CII standard. The link can be used in different FPGA structures. Implementation of the link enables object oriented VHDL programming with the use of CII standardization. The whole environment contains FPGA environment and PC software. The paper contains description of the selected issues of FPGA environment. There is description of some specific solutions that enables environment usage in structures of different producers. The flexibility of different size data transmissions with the use of CII is presented. The specified tool gives the opportunity to use FPGA structures variety fully and design faster and more effectively.

Toward a procedure for integrating moral issues in health technology assessment.

PubMed

Hofmann, Bjørn

2005-01-01

Although ethics has been on the agenda in health technology assessment (HTA) since its inception, the integration of moral issues is still not standard and is performed in a vast variety of ways. Therefore, there is a need for a procedure for integrating moral issues in HTA. Literature review of existing approaches together with application of various theories in moral philosophy and axiology. The article develops a set of questions that addresses a wide range of moral issues related to the assessment and implementation of health technology. The issues include general moral issues and moral issues related to stakeholders, methodology, characteristics of technology, and to the HTA process itself. The questions form a kind of checklist for use in HTAs. The presented approach for integrating moral issues in HTA has a broad theoretical foundation and has shown to be useful in practice. Integrating ethical issues in HTAs can be of great importance with respect to the dissemination of HTA results and in efficient health policy making.

Structural and thermal interface characteristics of Stirling cycle cryocoolers for space applications

NASA Technical Reports Server (NTRS)

Boyle, R.; James, E.; Miller, P.; Arillo, V.; Sparr, L.; Castles, S.

1991-01-01

Integration of a Stirling cycle cryocooler into a flight system will require careful attention to the thermal, structural, and electrical interfaces between the cryocooler, the instrument and the spacecraft. These issues are currently under investigation by National Aeronautics and Space Administration/Goddard Space Flight Center personnel in laboratory tests of representative longlife cryocoolers. An 80 K cryocooler has been instrumented as a testbed for vibration control systems characterization. Initial vibration data using a new six-DOF force dynamometer is presented in this report.

Metropolitan Public Library Funding and Intergovernmental Fiscal Relations: Concepts and Issues.

ERIC Educational Resources Information Center

Shirk, Gary M.

Competition among the many public services for tax supported funding is a major concern for metropolitan public libraries seeking financial support. The absence of the library is an integrated component of the public educational structure or as a general service agency in the mainstream of government has historically placed the library at a…

The Professional Transspective of the Students in the Conflicting Realities of the Post-Industrial Society

ERIC Educational Resources Information Center

Zinnatova, Mariya V.; Konovalova, Maria E.; Makarova, Nataliya V.

2016-01-01

The topicality of the issue under investigation is determined by the rising demand of the Russian society in the mastering and controlling conflicting realities that are capable of changing the integral notional structure of an individual, leading to the evolution or degradation of such individual's social and professional life activity. The…

ISE structural dynamic experiments

NASA Technical Reports Server (NTRS)

Lock, Malcolm H.; Clark, S. Y.

1988-01-01

The topics are presented in viewgraph form and include the following: directed energy systems - vibration issue; Neutral Particle Beam Integrated Space Experiment (NPB-ISE) opportunity/study objective; vibration sources/study plan; NPB-ISE spacecraft configuration; baseline slew analysis and results; modal contributions; fundamental pitch mode; vibration reduction approaches; peak residual vibration; NPB-ISE spacecraft slew experiment; goodbye ISE - hello Zenith Star Program.

Description of New Inflatable/Rigidizable Hexapod Structure Testbed for Shape and Vibration Control

NASA Technical Reports Server (NTRS)

Adetona, O.; Keel, L. H.; Horta, L. G.; Cadogan, D. P.; Sapna, G. H.; Scarborough, S. E.

2002-01-01

Larger and more powerful space based instruments are needed to meet increasingly sophisticated scientific demand. To support this need, concepts for telescopes with apertures of 100 meters are being investigated, but the required technologies are not in hand today. Due to the capacity limits of launch vehicles, the idea of deploying, erecting, or inflating large structures in space is being considered. Recently, rigidization concepts of large inflatable structures have demonstrated the capability of weight reductions of up to 50% from current concepts with packaging efficiencies near 80%. One of the important aspects of inflatable structures is vibration mitigation and line-of-sight control. Such control tasks are possible only after actuators/sensors are properly integrated into a rigidizable concept. To study these issues, we have developed an inflatable/rigidizable hexapod structure testbed. The testbed integrates state of the art piezo-electric self-sensing actuators into an inflatable/rigidizable structure and a flat membrane reflector. Using this testbed, we plan to experimentally demonstrate achievable vibration and line-of-sight control. This paper contains a description of the testbed and an outline of the test plan.

[Landscape classification: research progress and development trend].

PubMed

Liang, Fa-Chao; Liu, Li-Ming

2011-06-01

Landscape classification is the basis of the researches on landscape structure, process, and function, and also, the prerequisite for landscape evaluation, planning, protection, and management, directly affecting the precision and practicability of landscape research. This paper reviewed the research progress on the landscape classification system, theory, and methodology, and summarized the key problems and deficiencies of current researches. Some major landscape classification systems, e. g. , LANMAP and MUFIC, were introduced and discussed. It was suggested that a qualitative and quantitative comprehensive classification based on the ideology of functional structure shape and on the integral consideration of landscape classification utility, landscape function, landscape structure, physiogeographical factors, and human disturbance intensity should be the major research directions in the future. The integration of mapping, 3S technology, quantitative mathematics modeling, computer artificial intelligence, and professional knowledge to enhance the precision of landscape classification would be the key issues and the development trend in the researches of landscape classification.

How couples manage interracial and intercultural differences: implications for clinical practice.

PubMed

Seshadri, Gita; Knudson-Martin, Carmen

2013-01-01

This study focused on how couples managed their interracial and intercultural differences. To understand their experiences, a qualitative grounded theory analysis was used (n=17). Analysis revealed that couples experienced most issues as cultural issues; race only occurred during their interactions with "others." They appeared to organize their responses according to four relationship structures: Integrated, Singularly Assimilated, Coexisting, and Unresolved. Couples in each of these structures managed daily process through four sets of relationship strategies: (a) creating a "we," (b) framing differences, (c) emotional maintenance, and (d) positioning in relationship to familial and societal context. These findings are a step toward a strength-based and research-informed education and clinical interventions for this population. Video Abstract. © 2012 American Association for Marriage and Family Therapy.

Population health management in integrated physical and mental health care.

PubMed

Sieck, Cynthia J; Wickizer, Thomas; Geist, Laurel

2014-01-01

Individuals suffering from serious mental illness (SMI) face many challenges of navigating a complex and often fragmented health care system and may die significantly earlier from co-morbid physical health conditions. Integrating mental and physical health care for individuals with SMI is an emerging trend addressing the often-neglected physical health care needs of this population to better coordinate care and improve health outcomes. Population Health Management (PHM) provides a useful friamework for designing integrated care programs for individuals with SMI. This paper examines the structure and evolution of the integrated care program in Missouri in the context of PHM, highlighting particular elements of PHM that facilitate and support development of an integrated mental and physical health care program. As health care reform provides external motivation to provide integrated care, this study can be useful as other states attempt to address this important issue.

Validated Feasibility Study of Integrally Stiffened Metallic Fuselage Panels for Reducing Manufacturing Costs: Cost Assessment of Manufacturing/Design Concepts

NASA Technical Reports Server (NTRS)

Metschan, S.

2000-01-01

The objective of the Integral Airframe Structures (IAS) program was to demonstrate, for an integrally stiffened structural concept, performance and weight equal to "built-up" structure with lower manufacturing cost. This report presents results of the cost assessment for several design configuration/manufacturing method combinations. The attributes of various cost analysis models were evaluated and COSTRAN selected for this study. A process/design cost evaluation matrix was developed based on material, forming, machining, and assembly of structural sub-elements and assembled structure. A hybrid design, made from high-speed machined extruded frames that are mechanically fastened to high-speed machined plate skin/stringer panels, was identified as the most cost-effective manufacturing solution. Recurring labor and material costs of the hybrid design are up to 61 percent less than the current built-up technology baseline. This would correspond to a total cost reduction of $1.7 million per ship set for a 777-sized airplane. However, there are important outstanding issues with regard to the cost of capacity of high technology machinery, and the ability to cost-effectively provide surface finish acceptable to the commercial aircraft industry. The projected high raw material cost of large extrusions also played an important role in the trade-off between plate and extruded concepts.

Thermal Transport at Solid-Liquid Interfaces: High Pressure Facilitates Heat Flow through Nonlocal Liquid Structuring.

PubMed

Han, Haoxue; Mérabia, Samy; Müller-Plathe, Florian

2017-05-04

The integration of three-dimensional microelectronics is hampered by overheating issues inherent to state-of-the-art integrated circuits. Fundamental understanding of heat transfer across soft-solid interfaces is important for developing efficient heat dissipation capabilities. At the microscopic scale, the formation of a dense liquid layer at the solid-liquid interface decreases the interfacial heat resistance. We show through molecular dynamics simulations of n-perfluorohexane on a generic wettable surface that enhancement of the liquid structure beyond a single adsorbed layer drastically enhances interfacial heat conductance. Pressure is used to control the extent of the liquid layer structure. The interfacial thermal conductance increases with pressure values up to 16.2 MPa at room temperature. Furthermore, it is shown that liquid structuring enhances the heat-transfer rate of high-energy lattice waves by broadening the transmission peaks in the heat flux spectrum. Our results show that pressure is an important external parameter that may be used to control interfacial heat conductance at solid-soft interfaces.

Unattended sensors community of interest: expanding intelligence awareness, optimizing mission support

NASA Astrophysics Data System (ADS)

Helt, Paul J.; DuBois, Dennis

2012-06-01

The scope and success of Department of Defense (DoD), Intelligence Community (IC), and other United States Government (USG) Unattended Sensor efforts clearly requires a focused, expanded effort at integration and best practices development. Discussions with key stakeholders indicate strong support for the standup of an Unattended Sensors Community of Interest (USCOI) to improve visibility across programs and foster greater mission partnerships. The USCOI will advance understanding of legal and privacy issues, data sharing, Intelligence Surveillance and Reconnaissance (ISR) architecture integration standards, technical specifications, and other issues of common interest (power management, concealment, etc.); promoting opportunities for cost avoidance and improved effectiveness. Launching the USCOI concept provides a stakeholders' forum to identify, discuss, and facilitate Doctrine, Organization, Training, Material, Leadership, Personnel and Facilities (DOTMLPF) resolutions to issues related to the acquisition, development, and employment of unattended sensors across the DoD, IC, and broader USG, as appropriate. USCOI also provides a structured forum where appropriately cleared law enforcement can share operational and technical experiences and expertise on integration of unattended sensor data in existing/planned collection and analysis architectures. The USCOI concept can help facilitate extensive independent discussion across the community and enhance subject matter expert and leadership perspectives. Many senior leaders believe DoD and the IC have a great deal to learn from law enforcement use of unattended sensors and data integration. The USCOI will broaden awareness and open dialogue among users and developers across the interagency, law enforcement, and academia.

Benchmark matrix and guide: Part II.

PubMed

1991-01-01

In the last issue of the Journal of Quality Assurance (September/October 1991, Volume 13, Number 5, pp. 14-19), the benchmark matrix developed by Headquarters Air Force Logistics Command was published. Five horizontal levels on the matrix delineate progress in TQM: business as usual, initiation, implementation, expansion, and integration. The six vertical categories that are critical to the success of TQM are leadership, structure, training, recognition, process improvement, and customer focus. In this issue, "Benchmark Matrix and Guide: Part II" will show specifically how to apply the categories of leadership, structure, and training to the benchmark matrix progress levels. At the intersection of each category and level, specific behavior objectives are listed with supporting behaviors and guidelines. Some categories will have objectives that are relatively easy to accomplish, allowing quick progress from one level to the next. Other categories will take considerable time and effort to complete. In the next issue, Part III of this series will focus on recognition, process improvement, and customer focus.

Early Design Choices: Capture, Model, Integrate, Analyze, Simulate

NASA Technical Reports Server (NTRS)

Malin, Jane T.

2004-01-01

I. Designs are constructed incrementally to meet requirements and solve problems: a) Requirements types: objectives, scenarios, constraints, ilities. etc. b) Problem/issue types: risk/safety, cost/difficulty, interaction, conflict, etc. II. Capture requirements, problems and solutions: a) Collect design and analysis products and make them accessible for integration and analysis; b) Link changes in design requirements, problems and solutions; and c) Harvest design data for design models and choice structures. III. System designs are constructed by multiple groups designing interacting subsystems a) Diverse problems, choice criteria, analysis methods and point solutions. IV. Support integration and global analysis of repercussions: a) System implications of point solutions; b) Broad analysis of interactions beyond totals of mass, cost, etc.

Spacelab payload accommodation handbook. Preliminary issue

NASA Technical Reports Server (NTRS)

1976-01-01

The main characteristics of the Spacelab system are described. Sufficient information on Spacelab capabilities is provided to enable individual experimenters or payload planning groups to determine how their payload equipment can be accomodated by Spacelab topics discussed include major spacelab/experiment interfaces; Spacelab payload support systems and requirements the experiments must comply with to allow experiment design; and development and integration up to a level where a group of individual experiments are integrated into a complete Spacelab payload using Spacelab racks/floors and pallet segments. Integration of a complete Spacelab payload with Spacelab subsystems, primary module structure etc., integration of Spacelab with the Orbiter and basic operational aspects are also covered in this preliminary edition of the handbook which reflects the current Spacelab baseline design and is for information only.

Structural considerations for solar installers : an approach for small, simplified solar installations or retrofits.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Richards, Elizabeth H.; Schindel, Kay; Bosiljevac, Tom

2011-12-01

Structural Considerations for Solar Installers provides a comprehensive outline of structural considerations associated with simplified solar installations and recommends a set of best practices installers can follow when assessing such considerations. Information in the manual comes from engineering and solar experts as well as case studies. The objectives of the manual are to ensure safety and structural durability for rooftop solar installations and to potentially accelerate the permitting process by identifying and remedying structural issues prior to installation. The purpose of this document is to provide tools and guidelines for installers to help ensure that residential photovoltaic (PV) power systemsmore » are properly specified and installed with respect to the continuing structural integrity of the building.« less

Structural contingency theory and individual differences: examination of external and internal person-team fit.

PubMed

Hollenbeck, John R; Moon, Henry; Ellis, Aleksander P J; West, Bradley J; Ilgen, Daniel R; Sheppard, Lori; Porter, Christopher O L H; Wagner, John A

2002-06-01

This article develops and tests a structurally based, integrated theory of person-team fit. The theory developed is an extension of structural contingency theory and considers issues of external fit simultaneously with its examination of internal fit at the team level. Results from 80 teams working on an interdependent team task indicate that divisional structures demand high levels of cognitive ability on the part of teammembers. However, the advantages of high cognitive ability in divisional structures are neutralized when there is poor external fit between the structure and the environment. Instead, emotional stability becomes a critical factor among teammembers when a divisional structure is out of alignment with its environment. Individual differences seem to play little or no role in functional structures, regardless of the degree of external fit.

[Current teaching, learning and examination methods in medical education and potential applications in rehabilitative issues].

PubMed

Schwarzkopf, S R; Morfeld, M; Gülich, M; Lay, W; Horn, K; Mau, W

2007-04-01

With introduction of the new Federal Medical Licensing Regulations (Approbationsordnung) in Germany, integrated teaching in "Rehabilitation, Physical Medicine, Naturopathic Treatment" (Querschnittsbereich Q12) has become obligatory for the first time. Furthermore, the new Regulations require the medical faculties in Germany to realize an innovative didactic orientation in teaching. This paper provides an overview of recent applications of teaching techniques and examination methods in medical education with special consideration of the new integrated course Q12 and further teaching methods related to rehabilitative issues. Problem-oriented learning (POL), problem-based learning (PBL), bedside teaching, eLearning, and the examination methods Objective Structured Clinical Examination (OSCE) and Triple Jump are in the focus. This overview is intended as the basis for subsequent publications of the Commission for Undergraduate and Postgraduate Training of the German Society of Rehabilitation Science (DGRW), which will present examples of innovative teaching material.

Managing forest structure and fire hazard--a tool for planners.

Treesearch

M.C. Johnson; D.L. Peterson; C.L. Raymond

2006-01-01

Fire planners and other resource managers need to examine a range of potential fuel and vegetation treatments to select options that will lead to desired outcomes for fire hazard and natural resource conditions. A new approach to this issue integrates concepts and tools from silviculture and fuel science to quantify outcomes for a large number of treatment options in...

Composites research at NASA Lewis Research Center

NASA Technical Reports Server (NTRS)

Levine, Stanley R.; Duffy, Stephen; Vary, Alex; Nathal, Michael V.; Miner, Robert V.; Arnold, Steven M.; Castelli, Michael G.; Hopkins, Dale A.; Meador, Michael A.

1994-01-01

Composites research at NASA Lewis is focused on their applications in aircraft propulsion, space propulsion, and space power, with the first being predominant. Research on polymer-, metal-, and ceramic-matrix composites is being carried out from an integrated materials and structures viewpoint. This paper outlines some of the topics being pursued from the standpoint of key technical issues, current status, and future directions.

Left Inferior Frontal Cortex and Syntax: Function, Structure and Behaviour in Patients with Left Hemisphere Damage

ERIC Educational Resources Information Center

Tyler, Lorraine K.; Marslen-Wilson, William D.; Randall, Billi; Wright, Paul; Devereux, Barry J.; Zhuang, Jie; Papoutsi, Marina; Stamatakis, Emmanuel A.

2011-01-01

For the past 150 years, neurobiological models of language have debated the role of key brain regions in language function. One consistently debated set of issues concern the role of the left inferior frontal gyrus in syntactic processing. Here we combine measures of functional activity, grey matter integrity and performance in patients with left…

The Criticality of Norms to the Functional Imperatives of the Social Action System of College and University Work

ERIC Educational Resources Information Center

Braxton, John M.

2010-01-01

In this article, I assert that the work of colleges and universities forms a social action system. I array the critical positions represented in this issue according to the four functional imperatives of social action systems: adaptation, goal attainment, integration, and pattern maintenance. I discuss the role of normative structures for these…

Evaluating Model Fit for Growth Curve Models: Integration of Fit Indices from SEM and MLM Frameworks

ERIC Educational Resources Information Center

Wu, Wei; West, Stephen G.; Taylor, Aaron B.

2009-01-01

Evaluating overall model fit for growth curve models involves 3 challenging issues. (a) Three types of longitudinal data with different implications for model fit may be distinguished: balanced on time with complete data, balanced on time with data missing at random, and unbalanced on time. (b) Traditional work on fit from the structural equation…

Understanding the challenges of integrating scientists and clinical teachers in psychiatry education: findings from an innovative faculty development program.

PubMed

Martimianakis, Maria Athina Tina; Hodges, Brian D; Wasylenki, Donald

2009-01-01

Medical schools and departments of psychiatry around the world face challenges in integrating science with clinical teaching. This project was designed to identify attitudes toward the integration of science in clinical teaching and address barriers to collaboration between scientists and clinical teachers. The authors explored the interactions of 20 faculty members (10 scientists and 10 clinical teachers) taking part in a 1-year structured faculty development program, based on a partnership model, designed to encourage collaborative interaction between scientists and clinical teachers. Data were collected before, during, and after the program using participant observations, surveys, participant diaries, and focus groups. Qualitative data were analyzed iteratively using the method of meaning condensation, and further informed with descriptive statistics generated from the pre- and postsurveys. Scientists and clinicians were strikingly unfamiliar with each other's worldviews, work experiences, professional expectations, and approaches to teaching. The partnership model appeared to influence integration at a social level, and led to the identification of departmental structural barriers that aggravate the divide between scientists and clinical teachers. Issues related to the integration of social scientists in particular emerged. Creating a formal program to encourage interaction of scientists and clinical teachers provided a forum for identifying some of the barriers associated with the collaboration of scientists and clinical teachers. Our data point to directions for organizational structures and faculty development that support the integration of scientists from a wide range of disciplines with their clinical faculty colleagues.

Coastal risk forecast system

NASA Astrophysics Data System (ADS)

Sabino, André; Poseiro, Pedro; Rodrigues, Armanda; Reis, Maria Teresa; Fortes, Conceição J.; Reis, Rui; Araújo, João

2018-03-01

The run-up and overtopping by sea waves are two of the main processes that threaten coastal structures, leading to flooding, destruction of both property and the environment, and harm to people. To build early warning systems, the consequences and associated risks in the affected areas must be evaluated. It is also important to understand how these two types of spatial information integrate with sensor data sources and the risk assessment methodology. This paper describes the relationship between consequences and risk maps, their role in risk management and how the HIDRALERTA system integrates both aspects in its risk methodology. It describes a case study for Praia da Vitória Port, Terceira Island, Azores, Portugal, showing that the main innovations in this system are twofold: it represents the overtopping flow and consequent flooding, which are critical for coastal and port areas protected by maritime structures, and it works also as a risk assessment tool, extremely important for long-term planning and decision-making. Moreover, the implementation of the system considers possible known variability issues, enabling changes in its behaviour as needs arise. This system has the potential to become a useful tool for the management of coastal and port areas, due to its capacity to effectively issue warnings and assess risks.

Coastal risk forecast system

NASA Astrophysics Data System (ADS)

Sabino, André; Poseiro, Pedro; Rodrigues, Armanda; Reis, Maria Teresa; Fortes, Conceição J.; Reis, Rui; Araújo, João

2018-04-01

The run-up and overtopping by sea waves are two of the main processes that threaten coastal structures, leading to flooding, destruction of both property and the environment, and harm to people. To build early warning systems, the consequences and associated risks in the affected areas must be evaluated. It is also important to understand how these two types of spatial information integrate with sensor data sources and the risk assessment methodology. This paper describes the relationship between consequences and risk maps, their role in risk management and how the HIDRALERTA system integrates both aspects in its risk methodology. It describes a case study for Praia da Vitória Port, Terceira Island, Azores, Portugal, showing that the main innovations in this system are twofold: it represents the overtopping flow and consequent flooding, which are critical for coastal and port areas protected by maritime structures, and it works also as a risk assessment tool, extremely important for long-term planning and decision-making. Moreover, the implementation of the system considers possible known variability issues, enabling changes in its behaviour as needs arise. This system has the potential to become a useful tool for the management of coastal and port areas, due to its capacity to effectively issue warnings and assess risks.

The influence of the visual modality on language structure and conventionalization: insights from sign language and gesture.

PubMed

Perniss, Pamela; Özyürek, Asli; Morgan, Gary

2015-01-01

For humans, the ability to communicate and use language is instantiated not only in the vocal modality but also in the visual modality. The main examples of this are sign languages and (co-speech) gestures. Sign languages, the natural languages of Deaf communities, use systematic and conventionalized movements of the hands, face, and body for linguistic expression. Co-speech gestures, though non-linguistic, are produced in tight semantic and temporal integration with speech and constitute an integral part of language together with speech. The articles in this issue explore and document how gestures and sign languages are similar or different and how communicative expression in the visual modality can change from being gestural to grammatical in nature through processes of conventionalization. As such, this issue contributes to our understanding of how the visual modality shapes language and the emergence of linguistic structure in newly developing systems. Studying the relationship between signs and gestures provides a new window onto the human ability to recruit multiple levels of representation (e.g., categorical, gradient, iconic, abstract) in the service of using or creating conventionalized communicative systems. Copyright © 2015 Cognitive Science Society, Inc.

Neuronal basis of speech comprehension.

PubMed

Specht, Karsten

2014-01-01

Verbal communication does not rely only on the simple perception of auditory signals. It is rather a parallel and integrative processing of linguistic and non-linguistic information, involving temporal and frontal areas in particular. This review describes the inherent complexity of auditory speech comprehension from a functional-neuroanatomical perspective. The review is divided into two parts. In the first part, structural and functional asymmetry of language relevant structures will be discus. The second part of the review will discuss recent neuroimaging studies, which coherently demonstrate that speech comprehension processes rely on a hierarchical network involving the temporal, parietal, and frontal lobes. Further, the results support the dual-stream model for speech comprehension, with a dorsal stream for auditory-motor integration, and a ventral stream for extracting meaning but also the processing of sentences and narratives. Specific patterns of functional asymmetry between the left and right hemisphere can also be demonstrated. The review article concludes with a discussion on interactions between the dorsal and ventral streams, particularly the involvement of motor related areas in speech perception processes, and outlines some remaining unresolved issues. This article is part of a Special Issue entitled Human Auditory Neuroimaging. Copyright © 2013 Elsevier B.V. All rights reserved.

Downscaling remotely sensed imagery using area-to-point cokriging and multiple-point geostatistical simulation

NASA Astrophysics Data System (ADS)

Tang, Yunwei; Atkinson, Peter M.; Zhang, Jingxiong

2015-03-01

A cross-scale data integration method was developed and tested based on the theory of geostatistics and multiple-point geostatistics (MPG). The goal was to downscale remotely sensed images while retaining spatial structure by integrating images at different spatial resolutions. During the process of downscaling, a rich spatial correlation model in the form of a training image was incorporated to facilitate reproduction of similar local patterns in the simulated images. Area-to-point cokriging (ATPCK) was used as locally varying mean (LVM) (i.e., soft data) to deal with the change of support problem (COSP) for cross-scale integration, which MPG cannot achieve alone. Several pairs of spectral bands of remotely sensed images were tested for integration within different cross-scale case studies. The experiment shows that MPG can restore the spatial structure of the image at a fine spatial resolution given the training image and conditioning data. The super-resolution image can be predicted using the proposed method, which cannot be realised using most data integration methods. The results show that ATPCK-MPG approach can achieve greater accuracy than methods which do not account for the change of support issue.

Reflexive aerostructures: increased vehicle survivability

NASA Astrophysics Data System (ADS)

Margraf, Thomas W.; Hemmelgarn, Christopher D.; Barnell, Thomas J.; Franklin, Mark A.

2007-04-01

Aerospace systems stand to benefit significantly from the advancement of reflexive aerostructure technologies for increased vehicle survivability. Cornerstone Research Group Inc. (CRG) is developing lightweight, healable composite systems for use as primary load-bearing aircraft components. The reflexive system is comprised of piezoelectric structural health monitoring systems, localized thermal activation systems, and lightweight, healable composite structures. The reflexive system is designed to mimic the involuntary human response to damage. Upon impact, the structural health monitoring system will identify the location and magnitude of the damage, sending a signal to a discrete thermal activation control system to resistively heat the shape memory polymer (SMP) matrix composite above activation temperature, resulting in localized shape recovery and healing of the damaged areas. CRG has demonstrated SMP composites that can recover 90 percent of flexural yield stress and modulus after postfailure healing. During the development, CRG has overcome issues of discrete activation, structural health monitoring integration, and healable resin systems. This paper will address the challenges associated with development of a reflexive aerostructure, including integration of structural health monitoring, discrete healing, and healable shape memory resin systems.

Structured Open Urban Data: Understanding the Landscape.

PubMed

Barbosa, Luciano; Pham, Kien; Silva, Claudio; Vieira, Marcos R; Freire, Juliana

2014-09-01

A growing number of cities are now making urban data freely available to the public. Besides promoting transparency, these data can have a transformative effect in social science research as well as in how citizens participate in governance. These initiatives, however, are fairly recent and the landscape of open urban data is not well known. In this study, we try to shed some light on this through a detailed study of over 9,000 open data sets from 20 cities in North America. We start by presenting general statistics about the content, size, nature, and popularity of the different data sets, and then examine in more detail structured data sets that contain tabular data. Since a key benefit of having a large number of data sets available is the ability to fuse information, we investigate opportunities for data integration. We also study data quality issues and time-related aspects, namely, recency and change frequency. Our findings are encouraging in that most of the data are structured and published in standard formats that are easy to parse; there is ample opportunity to integrate different data sets; and the volume of data is increasing steadily. But they also uncovered a number of challenges that need to be addressed to enable these data to be fully leveraged. We discuss both our findings and issues involved in using open urban data.

Design and implementation of digital controllers for smart structures using field-programmable gate arrays

NASA Astrophysics Data System (ADS)

Kelly, Jamie S.; Bowman, Hiroshi C.; Rao, Vittal S.; Pottinger, Hardy J.

1997-06-01

Implementation issues represent an unfamiliar challenge to most control engineers, and many techniques for controller design ignore these issues outright. Consequently, the design of controllers for smart structural systems usually proceeds without regard for their eventual implementation, thus resulting either in serious performance degradation or in hardware requirements that squander power, complicate integration, and drive up cost. The level of integration assumed by the Smart Patch further exacerbates these difficulties, and any design inefficiency may render the realization of a single-package sensor-controller-actuator system infeasible. The goal of this research is to automate the controller implementation process and to relieve the design engineer of implementation concerns like quantization, computational efficiency, and device selection. We specifically target Field Programmable Gate Arrays (FPGAs) as our hardware platform because these devices are highly flexible, power efficient, and reprogrammable. The current study develops an automated implementation sequence that minimizes hardware requirements while maintaining controller performance. Beginning with a state space representation of the controller, the sequence automatically generates a configuration bitstream for a suitable FPGA implementation. MATLAB functions optimize and simulate the control algorithm before translating it into the VHSIC hardware description language. These functions improve power efficiency and simplify integration in the final implementation by performing a linear transformation that renders the controller computationally friendly. The transformation favors sparse matrices in order to reduce multiply operations and the hardware necessary to support them; simultaneously, the remaining matrix elements take on values that minimize limit cycles and parameter sensitivity. The proposed controller design methodology is implemented on a simple cantilever beam test structure using FPGA hardware. The experimental closed loop response is compared with that of an automated FPGA controller implementation. Finally, we explore the integration of FPGA based controllers into a multi-chip module, which we believe represents the next step towards the realization of the Smart Patch.

SPECIAL ISSUE ON OPTICAL PROCESSING OF INFORMATION: Realisation of video-frequency filters on the basis of a new mode of operation of an acousto-optical correlator with spatial integration

NASA Astrophysics Data System (ADS)

Ushakov, V. N.

1995-10-01

A video-frequency acousto-optical correlator with spatial integration, which widens the functional capabilities of correlation-type acousto-optical processors, is described. The correlator is based on a two-dimensional reference transparency and it can filter arbitrary video signals of spectral width limited by the pass band of an acousto-optical modulator. The calculated pulse characteristic is governed by the structure of the reference transparency. A procedure for the synthesis of this transparency is considered and experimental results are reported.

The background and theory of integrated risk management

NASA Technical Reports Server (NTRS)

Hunsucker, John L.

1995-01-01

While all good managers have always considered risk in their decision making, only recently have formal programs to do so been introduced. This report covers the logical structure behind the formulation of an integrated risk management plan (IRM). Included in the report are factors forcing the development of a formal plan to consider risk, the basic objective or purpose of an IRM, and desirable traits of such a plan. The report moves on to a discussion of background issues, seeks to formalize some definitions, and then discusses required information on threats. The report concludes with the steps for an IRM.

Knowledge-based nursing diagnosis

NASA Astrophysics Data System (ADS)

Roy, Claudette; Hay, D. Robert

1991-03-01

Nursing diagnosis is an integral part of the nursing process and determines the interventions leading to outcomes for which the nurse is accountable. Diagnoses under the time constraints of modern nursing can benefit from a computer assist. A knowledge-based engineering approach was developed to address these problems. A number of problems were addressed during system design to make the system practical extended beyond capture of knowledge. The issues involved in implementing a professional knowledge base in a clinical setting are discussed. System functions, structure, interfaces, health care environment, and terminology and taxonomy are discussed. An integrated system concept from assessment through intervention and evaluation is outlined.

The integrated analysis capability (IAC Level 2.0)

NASA Technical Reports Server (NTRS)

Frisch, Harold P.; Vos, Robert G.

1988-01-01

The critical data management issues involved in the development of the integral analysis capability (IAC), Level 2, to support the design analysis and performance evaluation of large space structures, are examined. In particular, attention is given to the advantages and disadvantages of the formalized data base; merging of the matrix and relational data concepts; data types, query operators, and data handling; sequential versus direct-access files; local versus global data access; programming languages and host machines; and data flow techniques. The discussion also covers system architecture, recent system level enhancements, executive/user interface capabilities, and technology applications.

From Synergy to Complexity: The Trend Toward Integrated Value Chain and Landscape Governance.

PubMed

Ros-Tonen, Mirjam A F; Reed, James; Sunderland, Terry

2018-07-01

This Editorial introduces a special issue that illustrates a trend toward integrated landscape approaches. Whereas two papers echo older "win-win" strategies based on the trade of non-timber forest products, ten papers reflect a shift from a product to landscape perspective. However, they differ from integrated landscape approaches in that they emanate from sectorial approaches driven primarily by aims such as forest restoration, sustainable commodity sourcing, natural resource management, or carbon emission reduction. The potential of such initiatives for integrated landscape governance and achieving landscape-level outcomes has hitherto been largely unaddressed in the literature on integrated landscape approaches. This special issue addresses this gap, with a focus on actor constellations and institutional arrangements emerging in the transition from sectorial to integrated approaches. This editorial discusses the trends arising from the papers, including the need for a commonly shared concern and sense of urgency; inclusive stakeholder engagement; accommodating and coordinating polycentric governance in landscapes beset with institutional fragmentation and jurisdictional mismatches; alignment with locally embedded initiatives and governance structures; and a framework to assess and monitor the performance of integrated multi-stakeholder approaches. We conclude that, despite a growing tendency toward integrated approaches at the landscape level, inherent landscape complexity renders persistent and significant challenges such as balancing multiple objectives, equitable inclusion of all relevant stakeholders, dealing with power and gender asymmetries, adaptive management based on participatory outcome monitoring, and moving beyond existing administrative, jurisdictional, and sectorial silos. Multi-stakeholder platforms and bridging organizations and individuals are seen as key in overcoming such challenges.

Error in the determination of the deformed shape of prismatic beams using the double integration of curvature

NASA Astrophysics Data System (ADS)

Sigurdardottir, Dorotea H.; Stearns, Jett; Glisic, Branko

2017-07-01

The deformed shape is a consequence of loading the structure and it is defined by the shape of the centroid line of the beam after deformation. The deformed shape is a universal parameter of beam-like structures. It is correlated with the curvature of the cross-section; therefore, any unusual behavior that affects the curvature is reflected through the deformed shape. Excessive deformations cause user discomfort, damage to adjacent structural members, and may ultimately lead to issues in structural safety. However, direct long-term monitoring of the deformed shape in real-life settings is challenging, and an alternative is indirect determination of the deformed shape based on curvature monitoring. The challenge of the latter is an accurate evaluation of error in the deformed shape determination, which is directly correlated with the number of sensors needed to achieve the desired accuracy. The aim of this paper is to study the deformed shape evaluated by numerical double integration of the monitored curvature distribution along the beam, and create a method to predict the associated errors and suggest the number of sensors needed to achieve the desired accuracy. The error due to the accuracy in the curvature measurement is evaluated within the scope of this work. Additionally, the error due to the numerical integration is evaluated. This error depends on the load case (i.e., the shape of the curvature diagram), the magnitude of curvature, and the density of the sensor network. The method is tested on a laboratory specimen and a real structure. In a laboratory setting, the double integration is in excellent agreement with the beam theory solution which was within the predicted error limits of the numerical integration. Consistent results are also achieved on a real structure—Streicker Bridge on Princeton University campus.

Monolithic integration of GaN-based light-emitting diodes and metal-oxide-semiconductor field-effect transistors.

PubMed

Lee, Ya-Ju; Yang, Zu-Po; Chen, Pin-Guang; Hsieh, Yung-An; Yao, Yung-Chi; Liao, Ming-Han; Lee, Min-Hung; Wang, Mei-Tan; Hwang, Jung-Min

2014-10-20

In this study, we report a novel monolithically integrated GaN-based light-emitting diode (LED) with metal-oxide-semiconductor field-effect transistor (MOSFET). Without additionally introducing complicated epitaxial structures for transistors, the MOSFET is directly fabricated on the exposed n-type GaN layer of the LED after dry etching, and serially connected to the LED through standard semiconductor-manufacturing technologies. Such monolithically integrated LED/MOSFET device is able to circumvent undesirable issues that might be faced by other kinds of integration schemes by growing a transistor on an LED or vice versa. For the performances of resulting device, our monolithically integrated LED/MOSFET device exhibits good characteristics in the modulation of gate voltage and good capability of driving injected current, which are essential for the important applications such as smart lighting, interconnection, and optical communication.

Integrality of the therapeutic and pharmaceutical care: a necessary debate

PubMed Central

Vieira, Fabiola Sulpino

2017-01-01

ABSTRACT The controversy surrounding the different interpretations on the integrality of therapeutic and pharmaceutical care has led to the delimitation of its scope by a law, but the issue has not been completely pacified. As a contribution to this debate, we aim to discuss the challenges to ensure the integrality of the therapeutic and pharmaceutical care, based on a conceptual approach on the meanings of integrality in the Brazilian Unified Health System (SUS). We identified important challenges to ensure the integrality of the therapeutic and pharmaceutical care in the SUS. These challenges are related to professional practices, the organization of actions and services, and the governmental response to health problems or to the treatment of specific population groups. For this end, governments need to carry out structuring actions and be efficient in using available resources so that existing problems can be overcome. PMID:29236879

Evaluating program integration and the rise in collaboration: case study of a palliative care network.

PubMed

Bainbridge, Daryl; Brazil, Kevin; Krueger, Paul; Ploeg, Jenny; Taniguchi, Alan; Darnay, Julie

2011-01-01

There is increasing global interest in using regional palliative care networks (PCNs) to integrate care and create systems that are more cost-effective and responsive. We examined a PCN that used a community development approach to build capacity for palliative care in each distinct community in a region of southern Ontario, Canada, with the goal of achieving a competent integrated system. Using a case study methodology, we examined a PCN at the structural level through a document review, a survey of 20 organizational administrators, and an interview with the network director. The PCN identified 14 distinct communities at different stages of development within the region. Despite the lack of some key features that would facilitate efficient palliative care delivery across these communities, administrators largely viewed the network partnership as beneficial and collaborative. The PCN has attempted to recognize specific needs in each local area. Change is gradual but participatory. There remain structural issues that may negatively affect the functioning of the PCN.

Modeling the Multi-Body System Dynamics of a Flexible Solar Sail Spacecraft

NASA Technical Reports Server (NTRS)

Kim, Young; Stough, Robert; Whorton, Mark

2005-01-01

Solar sail propulsion systems enable a wide range of space missions that are not feasible with current propulsion technology. Hardware concepts and analytical methods have matured through ground development to the point that a flight validation mission is now realizable. Much attention has been given to modeling the structural dynamics of the constituent elements, but to date an integrated system level dynamics analysis has been lacking. Using a multi-body dynamics and control analysis tool called TREETOPS, the coupled dynamics of the sailcraft bus, sail membranes, flexible booms, and control system sensors and actuators of a representative solar sail spacecraft are investigated to assess system level dynamics and control issues. With this tool, scaling issues and parametric trade studies can be performed to study achievable performance, control authority requirements, and control/structure interaction assessments.

Novel Material Integration for Reliable and Energy-Efficient NEM Relay Technology

NASA Astrophysics Data System (ADS)

Chen, I.-Ru

Energy-efficient switching devices have become ever more important with the emergence of ubiquitous computing. NEM relays are promising to complement CMOS transistors as circuit building blocks for future ultra-low-power information processing, and as such have recently attracted significant attention from the semiconductor industry and researchers. Relay technology potentially can overcome the energy efficiency limit for conventional CMOS technology due to several key characteristics, including zero OFF-state leakage, abrupt switching behavior, and potentially very low active energy consumption. However, two key issues must be addressed for relay technology to reach its full potential: surface oxide formation at the contacting surfaces leading to increased ON-state resistance after switching, and high switching voltages due to strain gradient present within the relay structure. This dissertation advances NEM relay technology by investigating solutions to both of these pressing issues. Ruthenium, whose native oxide is conductive, is proposed as the contacting material to improve relay ON-state resistance stability. Ruthenium-contact relays are fabricated after overcoming several process integration challenges, and show superior ON-state resistance stability in electrical measurements and extended device lifetime. The relay structural film is optimized via stress matching among all layers within the structure, to provide lower strain gradient (below 10E-3/microm -1) and hence lower switching voltage. These advancements in relay technology, along with the integration of a metallic interconnect layer, enable complex relay-based circuit demonstration. In addition to the experimental efforts, this dissertation theoretically analyzes the energy efficiency limit of a NEM switch, which is generally believed to be limited by the surface adhesion energy. New compact (<1 microm2 footprint), low-voltage (<0.1 V) switch designs are proposed to overcome this limit. The results pave a pathway to scaled energy-efficient electronic device technology.

The existential dimension in general practice: identifying understandings and experiences of general practitioners in Denmark

PubMed Central

Assing Hvidt, Elisabeth; Søndergaard, Jens; Ammentorp, Jette; Bjerrum, Lars; Gilså Hansen, Dorte; Olesen, Frede; Pedersen, Susanne S.; Timm, Helle; Timmermann, Connie; Hvidt, Niels Christian

2016-01-01

Objective The objective of this study is to identify points of agreement and disagreements among general practitioners (GPs) in Denmark concerning how the existential dimension is understood, and when and how it is integrated in the GP–patient encounter. Design A qualitative methodology with semi-structured focus group interviews was employed. Setting General practice setting in Denmark. Subjects Thirty-one GPs from two Danish regions between 38 and 68 years of age participated in seven focus group interviews. Results Although understood to involve broad life conditions such as present and future being and identity, connectedness to a society and to other people, the existential dimension was primarily reported integrated in connection with life-threatening diseases and death. Furthermore, integration of the existential dimension was characterized as unsystematic and intuitive. Communication about religious or spiritual questions was mostly avoided by GPs due to shyness and perceived lack of expertise. GPs also reported infrequent referrals of patients to chaplains. Conclusion GPs integrate issues related to the existential dimension in implicit and non-standardized ways and are hindered by cultural barriers. As a way to enhance a practice culture in which GPs pay more explicit attention to the patients’ multidimensional concerns, opportunities for professional development could be offered (courses or seminars) that focus on mutual sharing of existential reflections, ideas and communication competencies. Key pointsAlthough integration of the existential dimension is recommended for patient care in general practice, little is known about GPs’ understanding and integration of this dimension in the GP–patient encounter.The existential dimension is understood to involve broad and universal life conditions having no explicit reference to spiritual or religious aspects.The integration of the existential dimension is delimited to patient cases where life-threatening diseases, life crises and unexplainable patient symptoms occur. Integration of the existential dimension happens in unsystematic and intuitive ways.Cultural barriers such as shyness and lack of existential self-awareness seem to hinder GPs in communicating about issues related to the existential dimension. Educational initiatives might be needed in order to lessen barriers and enhance a more natural integration of communication about existential issues. PMID:27804316

Brain responses to filled gaps.

PubMed

Hestvik, Arild; Maxfield, Nathan; Schwartz, Richard G; Shafer, Valerie

2007-03-01

An unresolved issue in the study of sentence comprehension is whether the process of gap-filling is mediated by the construction of empty categories (traces), or whether the parser relates fillers directly to the associated verb's argument structure. We conducted an event-related potentials (ERP) study that used the violation paradigm to examine the time course and spatial distribution of brain responses to ungrammatically filled gaps. The results indicate that the earliest brain response to the violation is an early left anterior negativity (eLAN). This ERP indexes an early phase of pure syntactic structure building, temporally preceding ERPs that reflect semantic integration and argument structure satisfaction. The finding is interpreted as evidence that gap-filling is mediated by structurally predicted empty categories, rather than directly by argument structure operations.

Advanced Technology Composite Fuselage - Repair and Damage Assessment Supporting Maintenance

NASA Technical Reports Server (NTRS)

Flynn, B. W.; Bodine, J. B.; Dopker, B.; Finn, S. R.; Griess, K. H.; Hanson, C. T.; Harris, C. G.; Nelson, K. M.; Walker, T. H.; Kennedy, T. C.;

Integrating horizon scanning and strategic risk prioritisation using a weight of evidence framework to inform policy decisions.

PubMed

Garnett, K; Lickorish, F A; Rocks, S A; Prpich, G; Rathe, A A; Pollard, S J T

2016-08-01

Poor connection between data on emerging issues and credible policy decisions continues to challenge governments, and is only likely to grow as demands on time and resources increase. Here we summarise recent efforts to integrate horizon scanning and risk prioritisation approaches to better connect emerging issues to the political discourse on environmental and food-related issues. Our categorisation of insights including potential future risks and opportunities to inform policy discussions has emerged from a structured three-year programme of horizon scanning for a UK pan-governmental futures partnership led by the Department for Environment, Food and Rural Affairs (Defra). Our efforts to integrate horizon scanning and risk prioritisation, utilising a qualitative weight of evidence framework, has created a systematic process for identifying all signals of potential future change with significant impact for the strategic mission and underlying values of policy actors. Our approach encourages an exploration of factors out of the control of organisations, recognising that resilience depends on the flexibility of management strategies and the preparedness to deal with a variety of unexpected outcomes. We discuss how this approach addresses key cultural and evaluative challenges that policy actors have had in embedding horizon scanning in evidence-based policy processes, and suggest further developments to build confidence in the use of horizon scanning for strategic planning. Copyright © 2016 Elsevier B.V. All rights reserved.

Issues on Building Kazakhstan Geospatial Portal to Implement E-Government

NASA Astrophysics Data System (ADS)

Sagadiyev, K.; Kang, H. K.; Li, K. J.

2016-06-01

A main issue in developing e-government is about how to integrate and organize many complicated processes and different stakeholders. Interestingly geospatial information provides an efficient framework to integrate and organized them. In particular, it is very useful to integrate the process of land management in e-government with geospatial information framework, since most of land management tasks are related with geospatial properties. In this paper, we present a use-case on the e-government project in Kazakhstan for land management. We develop a geoportal to connect many tasks and different users via geospatial information framework. This geoportal is based on open source geospatial software including GeoServer, PostGIS, and OpenLayers. With this geoportal, we expect three achievements as follows. First we establish a transparent governmental process, which is one of main goal of e-government. Every stakeholder monitors what is happening in land management process. Second, we can significantly reduce the time and efforts in the government process. For example, a grant procedure for a building construction has taken more than one year with more than 50 steps. It is expected that this procedure would be reduced to 2 weeks by the geoportal framework. Third we provide a collaborative environment between different governmental structures via the geoportal, while many conflicts and mismatches have been a critical issue of governmental administration processes.

Structural and leakage integrity of tubes affected by circumferential cracking

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hernalsteen, P.

1997-02-01

In this paper the author deals with the notion that circumferential cracks are generally considered unacceptable. He argues for the need to differentiate two facets of such cracks: the issue of the size and growth rate of a crack; and the issue of the structural strength and leakage potential of the tube in the presence of the crack. In this paper the author tries to show that the second point is not a major concern for such cracks. The paper presents data on the structural strength or burst pressure characteristics of steam generator tubes derived from models and data basesmore » of experimental work. He also presents a leak rate model, and compares the performance of circumferential and axial cracks as far as burst strength and leak rate. The final conclusion is that subject to improvement in NDE capabilities (sizing, detection, growth), that Steam Generator Defect Specific Management can be used to allow circumferentially degraded tubes to remain in service.« less

Conceptualizing structural change in health promotion: why we still need to know more about theory.

PubMed

Gelius, Peter; Rütten, Alfred

2017-02-28

As recently discussed in the public health literature, many questions concerning 'structural' approaches in health promotion seem to remain unanswered. We argue that, before attempting to provide answers, it is essential to clarify the underlying theoretical assumptions in order to arrive at the right questions one should ask. To this end, we introduce into the current debate an existing theoretical framework that helps conceptualize structural and individual aspects of health promotion interventions at different levels of action. Using an example from the field of physical activity promotion, we illustrate how an integrated framework can help researchers and health promoters rethink important issues and design better interventions. In particular, such an approach may help overcome perceived distinctions between different types of approaches, re-conceptualize ideas about the effectiveness of interventions, and appropriately address issues of health disparities. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Fiber optics in composite materials: materials with nerves of glass

NASA Astrophysics Data System (ADS)

Measures, Raymond M.

1990-08-01

A Fiber Optic BasedSmart Structure wiipossess a structurally integrated optical microsensor system for determining its state. This built-in sensor system should, in real-time, be able to: evaluate the strain or deformation of a structure, monitor if its vibrating or subject to excessive loads, check its temperature and warn of the appearance of any hot spots. In addition a Smart Structure should maintain a vigilant survelliance over its structural integrity. The successful development of Smart StructureTechnolgy could lead to: aircraft that are safer, lighter, more efficient, easier to maintain and to service; pipelines, pressure vessels and storage tanks that constantly monitor their structuralintegrity and immediately issue an alert ifany problem is detected; space platforms that check forpressure leaks, unwanted vibration, excess thermal buildup, and deviation from some preassigned shape.This technology is particularly appropriate for composite materials where internal damage generated by: impacts, manufacturing flaws, excessive loading or fatigue could be detected and assessed. In service monitoring of structural loads, especially in regions like wing roots of aircraft, could be ofconsiderable benefit in helping to avoid structural overdesign and reduce weight. Structurally imbedded optical fibers sensors might also serve to monitor the cure state of composite thermosets during their fabrication and thereby contribute to improved quality control of these products.

Teaching foundational topics and scientific skills in biochemistry within the conceptual framework of HIV protease.

PubMed

Johnson, R Jeremy

2014-01-01

HIV protease has served as a model protein for understanding protein structure, enzyme kinetics, structure-based drug design, and protein evolution. Inhibitors of HIV protease are also an essential part of effective HIV/AIDS treatment and have provided great societal benefits. The broad applications for HIV protease and its inhibitors make it a perfect framework for integrating foundational topics in biochemistry around a big picture scientific and societal issue. Herein, I describe a series of classroom exercises that integrate foundational topics in biochemistry around the structure, biology, and therapeutic inhibition of HIV protease. These exercises center on foundational topics in biochemistry including thermodynamics, acid/base properties, protein structure, ligand binding, and enzymatic catalysis. The exercises also incorporate regular student practice of scientific skills including analysis of primary literature, evaluation of scientific data, and presentation of technical scientific arguments. Through the exercises, students also gain experience accessing computational biochemical resources such as the protein data bank, Proteopedia, and protein visualization software. As these HIV centered exercises cover foundational topics common to all first semester biochemistry courses, these exercises should appeal to a broad audience of undergraduate students and should be readily integrated into a variety of teaching styles and classroom sizes. © 2014 The International Union of Biochemistry and Molecular Biology.

Green buildings need good ergonomics.

PubMed

Hedge, A; Dorsey, J A

2013-01-01

A retrospective post-occupancy evaluation survey of 44 occupants in two Leadership in Energy and Environmental Design (LEED) Platinum buildings on a US college campus is reported. The Internet survey covered a range of indoor environment and ergonomics issues. Results show that working in these buildings were a generally positive experience for their health, performance and satisfaction. However, in one building there were persistent issues of variability in air temperature, air freshness, air quality and noise that affected the perceived health and performance of the occupants. Although the buildings were energy-efficient and sustainable structures, ergonomics design issues were identified. Implications for the role of ergonomics in green buildings and in the US LEED rating system are discussed. This survey identified a number of ergonomics design issues present in the LEED Platinum energy-efficient and sustainable buildings that were studied. These results highlight the importance of integrating ergonomics design into green buildings as a component in the US LEED rating system.

Assessing mismatches in ecosystem services proficiency across the urban fabric of Porto (Portugal): The influence of structural and socioeconomic variables

Treesearch

Marisa S. Graça; João F. Gonçalves; Paulo J.M. Alves; David J. Nowak; Robert Hoehn; Alexis Ellis; Paulo Farinha-Marques; Mario Cunha

2017-01-01

According to UN estimates, it is expected that the world population living in cities will exceed 66% in 2050 (United Nations, 2014). The complex and intense interaction of ecological and socioeconomic systems shaping cities has highlighted the need to foster an interdisciplinary approach to urban issues integrating Natural and Social Sciences (Alberti et al., 2003)....

75 FR 11435 - Airworthiness Directives; Airbus Model A300 B4-2C, B4-103, and B4-203 Airplanes; and Model A300...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-11

... operator reported that, during a routine inspection, the Right Hand frame 40 forward fitting between... result in a deterioration of the structural integrity of the frame. * * * * * We are issuing this AD to... operator reported that, during a routine inspection, the Right Hand frame 40 forward fitting between...

Air Mobility Command’s Total Force Integration: A Critical Analysis

DTIC Science & Technology

2012-02-26

variety of techniques available to positively change culture . 9 Changing assumptions of in-group collectivist requires increasing breadth and open...there have been issues. Command structure, cultural differences and vague guidance for implementation have plagued Air Mobility Command’s...through the Governor and not the President of the United States. Cultural Considerations The purpose of this section is to identify and discuss

Nickel Ferrite Nanoparticles Anchored onto Silica Nanofibers for Designing Magnetic and Flexible Nanofibrous Membranes.

PubMed

Hong, Feifei; Yan, Chengcheng; Si, Yang; He, Jianxin; Yu, Jianyong; Ding, Bin

2015-09-16

Many applications proposed for magnetic silica nanofibers require their assembly into a cellular membrane structure. The feature to keep structure stable upon large deformation is crucial for a macroscopic porous material which functions reliably. However, it remains a key issue to realize robust flexibility in two-dimensional (2D) magnetic silica nanofibrous networks. Here, we report that the combination of electrospun silica nanofibers with zein dip-coating can lead to the formation of flexible, magnetic, and hierarchical porous silica nanofibrous membranes (SNM). The 290 nm diameter silica nanofibers act as templates for the uniform anchoring of nickel ferrite nanoparticles (size of 50 nm). Benefiting from the homogeneous and stable nanofiber-nanoparticle composite structure, the resulting magnetic SNM can maintain their structure integrity under repeated bending as high as 180° and can facilely recover. The unique hierarchical structure also provides this new class of silica membrane with integrated properties of ultralow density, high porosity, large surface area, good magnetic responsiveness, robust dye adsorption capacity, and effective emulsion separation performance. Significantly, the synthesis of such fascinating membranes may provide new insight for further application of silica in a self-supporting, structurally adaptive, and 2D membrane form.

Ultrasonic guided wave interpretation for structural health inspections

NASA Astrophysics Data System (ADS)

Bingham, Jill Paisley

Structural Health Management (SHM) combines the use of onboard sensors with artificial intelligence algorithms to automatically identify and monitor structural health issues. A fully integrated approach to SHM systems demands an understanding of the sensor output relative to the structure, along with sophisticated prognostic systems that automatically draw conclusions about structural integrity issues. Ultrasonic guided wave methods allow us to examine the interaction of multimode signals within key structural components. Since they propagate relatively long distances within plate- and shell-like structures, guided waves allow inspection of greater areas with fewer sensors, making this technique attractive for a variety of applications. This dissertation describes the experimental development of automatic guided wave interpretation for three real world applications. Using the guided wave theories for idealized plates we have systematically developed techniques for identifying the mass loading of underwater limpet mines on US Navy ship hulls, characterizing type and bonding of protective coatings on large diameter pipelines, and detecting the thinning effects of corrosion on aluminum aircraft structural stringers. In each of these circumstances the signals received are too complex for interpretation without knowledge of the guided wave physics. We employ a signal processing technique called the Dynamic Wavelet Fingerprint Technique (DFWT) in order to render the guided wave mode information in two-dimensional binary images. The use of wavelets allows us to keep track of both time and scale features from the original signals. With simple image processing we have developed automatic extraction algorithms for features that correspond to the arrival times of the guided wave modes of interest for each of the applications. Due to the dispersive nature of the guided wave modes, the mode arrival times give details of the structure in the propagation path. For further understanding of how the guided wave modes propagate through the real structures, we have developed parallel processing, 3D elastic wave simulations using the finite integration technique (EFIT). This full field, numeric simulation technique easily examines models too complex for analytical solutions. We have developed the algorithm to handle built up 3D structures as well as layers with different material properties and surface detail. The simulations produce informative visualizations of the guided wave modes in the structures as well as the output from sensors placed in the simulation space to mimic the placement from experiment. Using the previously developed mode extraction algorithms we were then able to compare our 3D EFIT data to their experimental counterparts with consistency.

Issues and prospects for the next generation of the spatial data transfer standard (SDTS)

USGS Publications Warehouse

Arctur, D.; Hair, D.; Timson, G.; Martin, E.P.; Fegeas, R.

1998-01-01

The Spatial Data Transfer Standard (SDTS) was designed to be capable of representing virtually any data model, rather than being a prescription for a single data model. It has fallen short of this ambitious goal for a number of reasons, which this paper investigates. In addition to issues that might have been anticipated in its design, a number of new issues have arisen since its initial development. These include the need to support explicit feature definitions, incremental update, value-added extensions, and change tracking within large, national databases. It is time to consider the next stage of evolution for SDTS. This paper suggests development of an Object Profile for SDTS that would integrate concepts for a dynamic schema structure, OpenGIS interface, and CORBA IDL.

Theory and practice in interprofessional ethics: a framework for understanding ethical issues in health care teams.

PubMed

Clark, Phillip G; Cott, Cheryl; Drinka, Theresa J K

2007-12-01

Interprofessional teamwork is an essential and expanding form of health care practice. While moral issues arising in teamwork relative to the patient have been explored, the analysis of ethical issues regarding the function of the team itself is limited. This paper develops a conceptual framework for organizing and analyzing the different types of ethical issues in interprofessional teamwork. This framework is a matrix that maps the elements of principles, structures, and processes against individual, team, and organizational levels. A case study is presented that illustrates different dimensions of these topics, based on the application of this framework. Finally, a set of conclusions and recommendations is presented to summarize the integration of theory and practice in interprofessional ethics, including: (i) importance of a framework, (ii) interprofessional ethics discourse, and (iii) interprofessional ethics as an emerging field. The goal of this paper is to begin a dialogue and discussion on the ethical issues confronting interprofessional teams and to lay the foundation for an expanding discourse on interprofessional ethics.

Integration of remote sensing and GIS: Data and data access

USGS Publications Warehouse

Ehlers, M.; Greenlee, D.D.; Smith, T.; Star, J.

1991-01-01

CT: Theintegration of remote sensing tools and technology with the spatial analysis orientation of geographic information systems is a complex task. In this paper, we focus on the issues of making data available and useful to the user. In part, this involves a set of problems which reflect on the physical and logical structures used to encode the data. At the same time, however, the mechanisms and protocols which provide information about the data, and which maintain the data through time, have become increasingly important. We discuss these latter issues from the viewpoint of the functions which must be provided by archives of spatial data.

Structural verification for GAS experiments

NASA Technical Reports Server (NTRS)

Peden, Mark Daniel

1992-01-01

The purpose of this paper is to assist the Get Away Special (GAS) experimenter in conducting a thorough structural verification of its experiment structural configuration, thus expediting the structural review/approval process and the safety process in general. Material selection for structural subsystems will be covered with an emphasis on fasteners (GSFC fastener integrity requirements) and primary support structures (Stress Corrosion Cracking requirements and National Space Transportation System (NSTS) requirements). Different approaches to structural verifications (tests and analyses) will be outlined especially those stemming from lessons learned on load and fundamental frequency verification. In addition, fracture control will be covered for those payloads that utilize a door assembly or modify the containment provided by the standard GAS Experiment Mounting Plate (EMP). Structural hazard assessment and the preparation of structural hazard reports will be reviewed to form a summation of structural safety issues for inclusion in the safety data package.

Toward smart aerospace structures: design of a piezoelectric sensor and its analog interface for flaw detection.

PubMed

Boukabache, Hamza; Escriba, Christophe; Fourniols, Jean-Yves

2014-10-31

Structural health monitoring using noninvasive methods is one of the major challenges that aerospace manufacturers face in this decade. Our work in this field focuses on the development and the system integration of millimetric piezoelectric sensors/ actuators to generate and measure specific guided waves. The aim of the application is to detect mechanical flaws on complex composite and alloy structures to quantify efficiently the global structures' reliability. The study begins by a physical and analytical analysis of a piezoelectric patch. To preserve the structure's integrity, the transducers are directly pasted onto the surface which leads to a critical issue concerning the interfacing layer. In order to improve the reliability and mitigate the influence of the interfacing layer, the global equations of piezoelectricity are coupled with a load transfer model. Thus we can determine precisely the shear strain developed on the surface of the structure. To exploit the generated signal, a high precision analog charge amplifier coupled to a double T notch filter were designed and scaled. Finally, a novel joined time-frequency analysis based on a wavelet decomposition algorithm is used to extract relevant structures signatures. Finally, this paper provides examples of application on aircraft structure specimens and the feasibility of the system is thus demonstrated.

Toward Smart Aerospace Structures: Design of a Piezoelectric Sensor and Its Analog Interface for Flaw Detection

PubMed Central

Boukabache, Hamza; Escriba, Christophe; Fourniols, Jean-Yves

2014-01-01

Structural health monitoring using noninvasive methods is one of the major challenges that aerospace manufacturers face in this decade. Our work in this field focuses on the development and the system integration of millimetric piezoelectric sensors/ actuators to generate and measure specific guided waves. The aim of the application is to detect mechanical flaws on complex composite and alloy structures to quantify efficiently the global structures' reliability. The study begins by a physical and analytical analysis of a piezoelectric patch. To preserve the structure's integrity, the transducers are directly pasted onto the surface which leads to a critical issue concerning the interfacing layer. In order to improve the reliability and mitigate the influence of the interfacing layer, the global equations of piezoelectricity are coupled with a load transfer model. Thus we can determine precisely the shear strain developed on the surface of the structure. To exploit the generated signal, a high precision analog charge amplifier coupled to a double T notch filter were designed and scaled. Finally, a novel joined time-frequency analysis based on a wavelet decomposition algorithm is used to extract relevant structures signatures. Finally, this paper provides examples of application on aircraft structure specimens and the feasibility of the system is thus demonstrated. PMID:25365457

Issues and Impediments Faced by Canadian Teachers While Integrating ICT in Pedagogical Practice

ERIC Educational Resources Information Center

Saxena, Anoop

2017-01-01

Teachers in many schools struggle to integrate Information and Communications Technology (ICT) as part of their teaching practice. Among the issues faced by teachers when attempting to integrate ICT into their classrooms are gaps in ICT knowledge and skills, lack of training and inadequate support and scaffolding. Other issues include inability to…

Making psycholinguistics musical: Self-paced reading time evidence for shared processing of linguistic and musical syntax

PubMed Central

Robert Slevc, L.; Rosenberg, Jason C.; Patel, Aniruddh D.

2009-01-01

Linguistic processing–especially syntactic processing–is often considered a hallmark of human cognition, thus the domain-specificity or domain-generality of syntactic processing has attracted considerable debate. These experiments address this issue by simultaneously manipulating syntactic processing demands in language and music. Participants performed self-paced reading of garden-path sentences in which structurally unexpected words cause temporary syntactic processing difficulty. A musical chord accompanied each sentence segment, with the resulting sequence forming a coherent chord progression. When structurally unexpected words were paired with harmonically unexpected chords, participants showed substantially enhanced garden-path effects. No such interaction was observed when the critical words violated semantic expectancy, nor when the critical chords violated timbral expectancy. These results support a prediction of the shared syntactic integration resource hypothesis (SSIRH, Patel, 2003), which suggests that music and language draw on a common pool of limited processing resources for integrating incoming elements into syntactic structures. PMID:19293110

Integrative dimensions of psychotherapy training.

PubMed

Greben, Daniel H

2004-04-01

This paper investigates the influence of integrative factors on psychotherapy education. The broad relevance of integrative psychotherapy to residency training and continuing mental health education is discussed. Following a review of the existing literature on the education of integrative psychotherapists, the article systematically examines the integrative and pedagogic issues to be considered in planning psychotherapy training informed by integrative principles. The integrative issues are organized into 5 categories: attitudinal set, knowledge base, clinical techniques and skills, developmental tasks and challenges, and systemic institutional factors. The educational issues can be divided into 4 categories: content, format and process, sequence, and faculty development. Brief descriptions of actual educational interventions illustrate the implementation of such ideas. Specific recommendations are made regarding the development of integrative educational initiatives and future study of unresolved questions.

Strategic Issues in University Information Management

NASA Astrophysics Data System (ADS)

Roosendaal, Hans E.

This chapter represents a specific view on university management. It sequentially discusses different organizational levels of e-teaching, starting with general management, e-science developments and what this means to universities, and business models followed by focusing on specific teaching issues. The chapter sets out to discuss the development of the university from a loose federation of faculties into a more integrated university, such as, e.g., an entrepreneurial university. This development is also driven by the introduction of the bachelors/masters system - a process which leads to the need for an institutional strategy introducing institutional quality management and has to be accompanied by the independent accreditation of research and teaching. Applying the model of strategic positioning to the university as a whole leads to the introduction of the university entrepreneur. The model is used to describe structural issues and the relations between the primary processes of research and teaching with the secondary processes. e-science is introduced as a further step toward the universal sharing of scientific results and to analyze the kind of incentives that will be required to attain this goal of making information an even more integral part of the research and teaching process.

Human Systems Integration in Practice: Constellation Lessons Learned

NASA Technical Reports Server (NTRS)

Zumbado, Jennifer Rochlis

2012-01-01

NASA's Constellation program provided a unique testbed for Human Systems Integration (HSI) as a fundamental element of the Systems Engineering process. Constellation was the first major program to have HSI mandated by NASA's Human Rating document. Proper HSI is critical to the success of any project that relies on humans to function as operators, maintainers, or controllers of a system. HSI improves mission, system and human performance, significantly reduces lifecycle costs, lowers risk and minimizes re-design. Successful HSI begins with sufficient project schedule dedicated to the generation of human systems requirements, but is by no means solely a requirements management process. A top-down systems engineering process that recognizes throughout the organization, human factors as a technical discipline equal to traditional engineering disciplines with authority for the overall system. This partners with a bottoms-up mechanism for human-centered design and technical issue resolution. The Constellation Human Systems Integration Group (HSIG) was a part of the Systems Engineering and Integration (SE&I) organization within the program office, and existed alongside similar groups such as Flight Performance, Environments & Constraints, and Integrated Loads, Structures and Mechanisms. While the HSIG successfully managed, via influence leadership, a down-and-in Community of Practice to facilitate technical integration and issue resolution, it lacked parallel top-down authority to drive integrated design. This presentation will discuss how HSI was applied to Constellation, the lessons learned and best practices it revealed, and recommendations to future NASA program and project managers. This presentation will discuss how Human Systems Integration (HSI) was applied to NASA's Constellation program, the lessons learned and best practices it revealed, and recommendations to future NASA program and project managers on how to accomplish this critical function.

Self-assembly micro optical filter

NASA Astrophysics Data System (ADS)

Zhang, Ping (Cerina); Le, Kevin; Malalur-Nagaraja-Rao, Smitha; Hsu, Lun-Chen; Chiao, J.-C.

2006-01-01

Optical communication and sensor industry face critical challenges in manufacturing for system integration. Due to the assembly complexity and integration platform variety, micro optical components require costly alignment and assembly procedures, in which many required manual efforts. Consequently, self-assembly device architectures have become a great interest and could provide major advantages over the conventional optical devices. In this paper, we discussed a self-assembly integration platform for micro optical components. To demonstrate the adaptability and flexibility of the proposed optical device architectures, we chose a commercially available MEMS fabrication foundry service - MUMPs (Multi-User MEMS Process). In this work, polysilicon layers of MUMPS are used as the 3-D structural material for construction of micro component framework and actuators. However, because the polysilicon has high absorption in the visible and near infrared wavelength ranges, it is not suitable for optical interaction. To demonstrate the required optical performance, hybrid integration of materials was proposed and implemented. Organic compound materials were applied on the silicon-based framework to form the required optical interfaces. Organic compounds provide good optical transparency, flexibility to form filters or lens and inexpensive manufacturing procedures. In this paper, we have demonstrated a micro optical filter integrated with self-assembly structures. We will discuss the self-assembly mechanism, optical filter designs, fabrication issues and results.

Integrated Education. Feature Issue.

ERIC Educational Resources Information Center

York, Jennifer, Ed.; Vandercook, Terri, Ed.

1988-01-01

This "feature issue" provides various perspectives on a number of integrated education topics, including successful integration practices and strategies, the changing roles of teachers, the appropriate role of research, the history and future of integrated education, and the realization of dreams of life in the mainstream for children with severe…

Modeling Pilot Pulse Control

NASA Technical Reports Server (NTRS)

Bachelder, Edward; Hess, Ronald; Godfroy-Cooper, Martine; Aponso, Bimal

2017-01-01

In this study, behavioral models are developed that closely reproduced pulsive control response of two pilots from the experimental pool using markedly different control techniques (styles) while conducting a tracking task. An intriguing find was that the pilots appeared to: 1) produce a continuous, internally-generated stick signal that they integrated in time; 2) integrate the actual stick position; and 3) compare the two integrations to issue and cease pulse commands. This suggests that the pilots utilized kinesthetic feedback in order to perceive and integrate stick position, supporting the hypothesis that pilots can access and employ the proprioceptive inner feedback loop proposed by Hess' pilot Structural Model. The Pulse Models used in conjunction with the pilot Structural Model closely recreated the pilot data both in the frequency and time domains during closed-loop simulation. This indicates that for the range of tasks and control styles encountered, the models captured the fundamental mechanisms governing pulsive and control processes. The pilot Pulse Models give important insight for the amount of remnant (stick output uncorrelated with the forcing function) that arises from nonlinear pilot technique, and for the remaining remnant arising from different sources unrelated to tracking control (i.e. neuromuscular tremor, reallocation of cognitive resources, etc.).

Integrated input protection against discharges for Micro Pattern Gas Detectors readout ASICs

NASA Astrophysics Data System (ADS)

Fiutowski, T.; Dąbrowski, W.; Koperny, S.; Wiącek, P.

2017-02-01

Immunity against possible random discharges inside active detector volume of MPGDs is one of the key aspects that should be addressed in the design of the front-end electronics. This issue becomes particularly critical for systems with high channel counts and high density readout employing the front-end electronics built as multichannel ASICs implemented in modern CMOS technologies, for which the breakdown voltages are in the range of a few Volts. The paper presents the design of various input protection structures integrated in the ASIC manufactured in a 350 nm CMOS process and test results using an electrical circuit to mimic discharges in the detectors.

Design, evaluation and test of an electronic, multivariable control for the F100 turbofan engine

NASA Technical Reports Server (NTRS)

Skira, C. A.; Dehoff, R. L.; Hall, W. E., Jr.

1980-01-01

A digital, multivariable control design procedure for the F100 turbofan engine is described. The controller is based on locally linear synthesis techniques using linear, quadratic regulator design methods. The control structure uses an explicit model reference form with proportional and integral feedback near a nominal trajectory. Modeling issues, design procedures for the control law and the estimation of poorly measured variables are presented.

Opportunities of CMOS-MEMS integration through LSI foundry and open facility

NASA Astrophysics Data System (ADS)

Mita, Yoshio; Lebrasseur, Eric; Okamoto, Yuki; Marty, Frédéfic; Setoguchi, Ryota; Yamada, Kentaro; Mori, Isao; Morishita, Satoshi; Imai, Yoshiaki; Hosaka, Kota; Hirakawa, Atsushi; Inoue, Shu; Kubota, Masanori; Denoual, Matthieu

2017-06-01

Since the 2000s, several countries have established micro- and nanofabrication platforms for the research and education community as national projects. By combining such platforms with VLSI multichip foundry services, various integrated devices, referred to as “CMOS-MEMS”, can be realized without constructing an entire cleanroom. In this paper, we summarize MEMS-last postprocess schemes for CMOS devices on a bulk silicon wafer as well as on a silicon-on-insulator (SOI) wafer using an open-access cleanroom of the Nanotechnology Platform of MEXT Japan. The integration devices presented in this article are free-standing structures and postprocess isolated LSI devices. Postprocess issues are identified with their solutions, such as the reactive ion etching (RIE) lag for dry release and the impact of the deep RIE (DRIE) postprocess on transistor characteristics. Integration with nonsilicon materials is proposed as one of the future directions.

Toward “optimal” integration of terrestrial biosphere models

DOE PAGES

Schwalm, Christopher R.; Huntzinger, Deborah N.; Fisher, Joshua B.; ...

2015-06-10

Multimodel ensembles (MME) are commonplace in Earth system modeling. Here we perform MME integration using a 10-member ensemble of terrestrial biosphere models (TBMs) from the Multiscale synthesis and Terrestrial Model Intercomparison Project (MsTMIP). We contrast optimal (skill based for present-day carbon cycling) versus naive (one model-one vote) integration. MsTMIP optimal and naive mean land sink strength estimates (-1.16 versus -1.15 Pg C per annum respectively) are statistically indistinguishable. This holds also for grid cell values and extends to gross uptake, biomass, and net ecosystem productivity. TBM skill is similarly indistinguishable. The added complexity of skill-based integration does not materially changemore » MME values. This suggests that carbon metabolism has predictability limits and/or that all models and references are misspecified. Finally, resolving this issue requires addressing specific uncertainty types (initial conditions, structure, and references) and a change in model development paradigms currently dominant in the TBM community.« less

IMG 4 version of the integrated microbial genomes comparative analysis system

PubMed Central

Markowitz, Victor M.; Chen, I-Min A.; Palaniappan, Krishna; Chu, Ken; Szeto, Ernest; Pillay, Manoj; Ratner, Anna; Huang, Jinghua; Woyke, Tanja; Huntemann, Marcel; Anderson, Iain; Billis, Konstantinos; Varghese, Neha; Mavromatis, Konstantinos; Pati, Amrita; Ivanova, Natalia N.; Kyrpides, Nikos C.

2014-01-01

The Integrated Microbial Genomes (IMG) data warehouse integrates genomes from all three domains of life, as well as plasmids, viruses and genome fragments. IMG provides tools for analyzing and reviewing the structural and functional annotations of genomes in a comparative context. IMG’s data content and analytical capabilities have increased continuously since its first version released in 2005. Since the last report published in the 2012 NAR Database Issue, IMG’s annotation and data integration pipelines have evolved while new tools have been added for recording and analyzing single cell genomes, RNA Seq and biosynthetic cluster data. Different IMG datamarts provide support for the analysis of publicly available genomes (IMG/W: http://img.jgi.doe.gov/w), expert review of genome annotations (IMG/ER: http://img.jgi.doe.gov/er) and teaching and training in the area of microbial genome analysis (IMG/EDU: http://img.jgi.doe.gov/edu). PMID:24165883

IMG 4 version of the integrated microbial genomes comparative analysis system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Markowitz, Victor M.; Chen, I-Min A.; Palaniappan, Krishna

The Integrated Microbial Genomes (IMG) data warehouse integrates genomes from all three domains of life, as well as plasmids, viruses and genome fragments. IMG provides tools for analyzing and reviewing the structural and functional annotations of genomes in a comparative context. IMG’s data content and analytical capabilities have increased continuously since its first version released in 2005. Since the last report published in the 2012 NAR Database Issue, IMG’s annotation and data integration pipelines have evolved while new tools have been added for recording and analyzing single cell genomes, RNA Seq and biosynthetic cluster data. Finally, different IMG datamarts providemore » support for the analysis of publicly available genomes (IMG/W: http://img.jgi.doe.gov/w), expert review of genome annotations (IMG/ER: http://img.jgi.doe.gov/er) and teaching and training in the area of microbial genome analysis (IMG/EDU: http://img.jgi.doe.gov/edu).« less

IMG 4 version of the integrated microbial genomes comparative analysis system.

PubMed

Markowitz, Victor M; Chen, I-Min A; Palaniappan, Krishna; Chu, Ken; Szeto, Ernest; Pillay, Manoj; Ratner, Anna; Huang, Jinghua; Woyke, Tanja; Huntemann, Marcel; Anderson, Iain; Billis, Konstantinos; Varghese, Neha; Mavromatis, Konstantinos; Pati, Amrita; Ivanova, Natalia N; Kyrpides, Nikos C

2014-01-01

The Integrated Microbial Genomes (IMG) data warehouse integrates genomes from all three domains of life, as well as plasmids, viruses and genome fragments. IMG provides tools for analyzing and reviewing the structural and functional annotations of genomes in a comparative context. IMG's data content and analytical capabilities have increased continuously since its first version released in 2005. Since the last report published in the 2012 NAR Database Issue, IMG's annotation and data integration pipelines have evolved while new tools have been added for recording and analyzing single cell genomes, RNA Seq and biosynthetic cluster data. Different IMG datamarts provide support for the analysis of publicly available genomes (IMG/W: http://img.jgi.doe.gov/w), expert review of genome annotations (IMG/ER: http://img.jgi.doe.gov/er) and teaching and training in the area of microbial genome analysis (IMG/EDU: http://img.jgi.doe.gov/edu).

Ontology-Based Administration of Web Directories

NASA Astrophysics Data System (ADS)

Horvat, Marko; Gledec, Gordan; Bogunović, Nikola

Administration of a Web directory and maintenance of its content and the associated structure is a delicate and labor intensive task performed exclusively by human domain experts. Subsequently there is an imminent risk of a directory structures becoming unbalanced, uneven and difficult to use to all except for a few users proficient with the particular Web directory and its domain. These problems emphasize the need to establish two important issues: i) generic and objective measures of Web directories structure quality, and ii) mechanism for fully automated development of a Web directory's structure. In this paper we demonstrate how to formally and fully integrate Web directories with the Semantic Web vision. We propose a set of criteria for evaluation of a Web directory's structure quality. Some criterion functions are based on heuristics while others require the application of ontologies. We also suggest an ontology-based algorithm for construction of Web directories. By using ontologies to describe the semantics of Web resources and Web directories' categories it is possible to define algorithms that can build or rearrange the structure of a Web directory. Assessment procedures can provide feedback and help steer the ontology-based construction process. The issues raised in the article can be equally applied to new and existing Web directories.

Workshop report: US-China workshop on smart structures and smart systems

NASA Astrophysics Data System (ADS)

Tomizuka, Masayoshi

2006-03-01

A Joint U.S.-China workshop on the topic of Integrated Sensing Systems, Mechatronics and Smart Structures Technologies was held in Jinan, China in October 2005 to evaluate the current status of research and education in the topic areas in the United States and China, to identify critical and strategic research and educational issues of mutual interest, and to identify joint research projects and potential research teams for collaborative research activities. The workshop included a series of presentations by leading researchers and educators from the United States and China and group discussions on the workshop objectives.

Practical Considerations for Using Constant Force Springs in Space-Based Mechanisms

NASA Technical Reports Server (NTRS)

Williams, R. Brett; Fisher, Charles D.; Gallon, John C.

2013-01-01

Mechanical springs are a common element in mechanism from all walks of life; cars, watches, appliances, and many others. These springs generally exhibit a linear relationship between force and deflection. In small mechanisms, deflections are small so the variation in spring force between one position and another are generally small and do not influence the design or functionality of the device. However, as the spacecraft industry drives towards larger, deployable satellites, the distances a spring or springs must function over can become considerable so much so that the structural integrity of the device may be impacted. As such, an increasingly common mechanism element is the constant force spring- one that provides a constant force regardless of deflection. These elements are commonly in the conceptual design phase to deal with system-level large deflections, but in the detailed design or integration test phase they can pose significant implementation issues. This article addresses some of the detailed issues in order for these constant force springs to be properly designed into space systems.

International organizations to enable world-wide mobile satellite services

NASA Technical Reports Server (NTRS)

Anglin, Richard L., Jr.

1993-01-01

Numbers of systems exist or have been proposed to provide world-wide mobile satellite services (MSS). Developers of these systems have formulated institutional structures they consider most appropriate for profitable delivery of these services. MSS systems provide niche services and complement traditional telecommunications networks; they are not integrated into world-wide networks. To be successful, MSS system operators must be able to provide an integrated suite of services to support the increasing globalization, interconnectivity, and mobility of business. The critical issue to enabling 'universal roaming' is securing authority to provide MSS in all of the nations of the world. Such authority must be secured in the context of evolving trends in international telecommunications, and must specifically address issues of standardization, regulation and organization. Today, only one existing organization has such world-wide authority. The question is how proponents of new MSS systems and services can gain similar authority. Securing the appropriate authorizations requires that these new organizations reflect the objectives of the nations in which services are to be delivered.

Methods for heat transfer and temperature field analysis of the insulated diesel

NASA Technical Reports Server (NTRS)

Morel, T.; Blumberg, P. N.; Fort, E. F.; Keribar, R.

1984-01-01

Work done during phase 1 of a three-year program aimed at developing a comprehensive heat transfer and thermal analysis methodology oriented specifically to the design requirements of insulated diesel engines is reported. The technology developed in this program makes possible a quantitative analysis of the low heat rejection concept. The program is comprehensive in that it addresses all the heat transfer issues that are critical to the successful development of the low heat rejection diesel engine: (1) in-cylinder convective and radiative heat transfer; (2) cyclic transient heat transfer in thin solid layers at component surfaces adjacent to the combustion chamber; and (3) steady-state heat conduction in the overall engine structure. The Integral Technologies, Inc. (ITI) program is comprised of a set of integrated analytical and experimental tasks. A detailed review of the ITI program approach is provided, including the technical issues which underlie it and a summay of the methods that were developed.

Fundamental understanding and rational design of high energy structural microbatteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Yuxing; Li, Qiuyan; Cartmell, Samuel

Microbatteries play a critical role in determining the lifetime of downsized sensors, wearable devices and medical applications, etc. More often, structural batteries are required from the perspective of aesthetics and space utilization, which is however rarely explored. Herein, we discuss the fundamental issues associated with the rational design of practically usable high energy microbatteries. The tubular shape of the cell further allows the flexible integration of microelectronics. A functioning acoustic micro-transmitter continuously powered by this tubular battery has been successfully demonstrated. Multiple design features adopted to accommodate large mechanical stress during the rolling process are discussed providing new insights inmore » designing the structural microbatteries for emerging technologies.« less

77 FR 65506 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-29

...We propose to supersede an existing airworthiness directive (AD) that applies to certain The Boeing Company Model 757-200 and - 200PF series airplanes. The existing AD currently requires modification of the nacelle strut and wing structure, and repair of any damage found during the modification. Since we issued that AD, a compliance time error involving the optional threshold formula was discovered, which could allow an airplane to exceed the acceptable compliance time for addressing the unsafe condition. This proposed AD would specify a maximum compliance time limit that overrides the optional threshold formula results. We are proposing this AD to prevent fatigue cracking in primary strut structure and consequent reduced structural integrity of the strut.

Localized synthesis, assembly and integration of silicon nanowires

NASA Astrophysics Data System (ADS)

Englander, Ongi

Localized synthesis, assembly and integration of one-dimensional silicon nanowires with MEMS structures is demonstrated and characterized in terms of local synthesis processes, electric-field assisted self-assembly, and a proof-of-concept nanoelectromechanical system (HEMS) demonstration. Emphasis is placed on the ease of integration, process control strategies, characterization techniques and the pursuit of integrated devices. A top-down followed by a bottom-up integration approach is utilized. Simple MEMS heater structures are utilized as the microscale platforms for the localized, bottom-up synthesis of one-dimensional nanostructures. Localized heating confines the high temperature region permitting only localized nanostructure synthesis and allowing the surroundings to remain at room temperature thus enabling CMOS compatible post-processing. The vapor-liquid-solid (VLS) process in the presence of a catalytic nanoparticle, a vapor phase reactant, and a specific temperature environment is successfully employed locally. Experimentally, a 5nm thick gold-palladium layer is used as the catalyst while silane is the vapor phase reactant. The current-voltage behavior of the MEMS structures can be correlated to the approximate temperature range required for the VLS reaction to take place. Silicon nanowires averaging 45nm in diameter and up to 29mum in length synthesized at growth rates of up to 1.5mum/min result. By placing two MEMS structures in close proximity, 4--10mum apart, localized silicon nanowire growth can be used to link together MEMS structures to yield a two-terminal, self-assembled micro-to-nano system. Here, one MEMS structure is designated as the hot growth structure while a nearby structure is designated as the cold secondary structure, whose role is to provide a natural stopping point for the VLS reaction. The application of a localized electric-field, 5 to 13V/mum in strength, during the synthesis process, has been shown to improve nanowire organization, alignment, and assembly. The integrated nanoelectrormechanical system was found to be mechanically resilient as it proved to successfully withstand a wide variety of post-processing steps, including manipulations and examinations under scanning and transmission electron microscopes and aqueous processing, although a super critical drying step is necessary to preserve the integrated system during the drying process. Electrical characterization of the system proved challenging due to low carrier concentration and possible transport issues at the nano-micro interface. Nonetheless, in a proof-of-concept demonstration, the system was functionalized and tested for a hydrogen sensing application.

Systems Engineering and Integration for Advanced Life Support System and HST

NASA Technical Reports Server (NTRS)

Kamarani, Ali K.

2005-01-01

Systems engineering (SE) discipline has revolutionized the way engineers and managers think about solving issues related to design of complex systems: With continued development of state-of-the-art technologies, systems are becoming more complex and therefore, a systematic approach is essential to control and manage their integrated design and development. This complexity is driven from integration issues. In this case, subsystems must interact with one another in order to achieve integration objectives, and also achieve the overall system's required performance. Systems engineering process addresses these issues at multiple levels. It is a technology and management process dedicated to controlling all aspects of system life cycle to assure integration at all levels. The Advanced Integration Matrix (AIM) project serves as the systems engineering and integration function for the Human Support Technology (HST) program. AIM provides means for integrated test facilities and personnel for performance trade studies, analyses, integrated models, test results, and validated requirements of the integration of HST. The goal of AIM is to address systems-level integration issues for exploration missions. It will use an incremental systems integration approach to yield technologies, baselines for further development, and possible breakthrough concepts in the areas of technological and organizational interfaces, total information flow, system wide controls, technical synergism, mission operations protocols and procedures, and human-machine interfaces.

Integrating Climate Change Adaptation into Disaster Risk Reduction in Urban Contexts: Perceptions and Practice

PubMed Central

Rivera, Claudia

2014-01-01

This paper analyses the perceptions of disaster risk reduction (DRR) practitioners concerning the on-going integration of climate change adaptation (CCA) into their practices in urban contexts in Nicaragua. Understanding their perceptions is important as this will provide information on how this integration can be improved. Exploring the perceptions of practitioners in Nicaragua is important as the country has a long history of disasters, and practitioners have been developing the current DRR planning framework for more than a decade. The analysis is based on semi-structured interviews designed to collect information about practitioners’ understanding of: (a) CCA, (b) the current level of integration of CCA into DRR and urban planning, (c) the opportunities and constraints of this integration, and (d) the potential to adapt cities to climate change. The results revealed that practitioners’ perception is that the integration of CCA into their practice is at an early stage, and that they need to improve their understanding of CCA in terms of a development issue. Three main constraints on improved integration were identified: (a) a recognized lack of understanding of CCA, (b) insufficient guidance on how to integrate it, and (c) the limited opportunities to integrate it into urban planning due to a lack of instruments and capacity in this field. Three opportunities were also identified: (a) practitioners’ awareness of the need to integrate CCA into their practices, (b) the robust structure of the DRR planning framework in the country, which provides a suitable channel for facilitating integration, and (c) the fact that CCA is receiving more attention and financial and technical support from the international community. PMID:24475365

Constraints on Composition, Structure and Evolution of the Lithosphere

NASA Astrophysics Data System (ADS)

Bianchini, Gianluca; Bonadiman, Costanza; Aulbach, Sonja; Schutt, Derek

2015-05-01

The idea for this special issue was triggered at the Goldschmidt Conference held in Florence (August 25-30, 2013), where we convened a session titled "Integrated Geophysical-Geochemical Constraints on Composition and Structure of the Lithosphere". The invitation to contribute was extended not only to the session participants but also to a wider spectrum of colleagues working on related topics. Consequently, a diverse group of Earth scientists encompassing geophysicists, geodynamicists, geochemists and petrologists contributed to this Volume, providing a comprehensive overview on the nature and evolution of lithospheric mantle by combining studies that exploit different types of data and interpretative approaches. The integration of geochemical and geodynamic datasets and their interpretation represents the state of the art in our knowledge of the lithosphere and beyond, and could serve as a blueprint for future strategies in concept and methodology to advance our knowledge of this and other terrestrial reservoirs.

A comprehensive strategy for designing a Web-based medical curriculum.

PubMed Central

Zucker, J.; Chase, H.; Molholt, P.; Bean, C.; Kahn, R. M.

1996-01-01

In preparing for a full featured online curriculum, it is necessary to develop scaleable strategies for software design that will support the pedagogical goals of the curriculum and which will address the issues of acquisition and updating of materials, of robust content-based linking, and of integration of the online materials into other methods of learning. A complete online curriculum, as distinct from an individual computerized module, must provide dynamic updating of both content and structure and an easy pathway from the professor's notes to the finished online product. At the College of Physicians and Surgeons, we are developing such strategies including a scripted text conversion process that uses the Hypertext Markup Language (HTML) as structural markup rather than as display markup, automated linking by the use of relational databases and the Unified Medical Language System (UMLS), integration of text, images, and multimedia along with interface designs which promote multiple contexts and collaborative study. PMID:8947624

J-resistance curves for Inconel 690 and Incoloy 800 nuclear steam generators tubes at room temperature and at 300 °C

NASA Astrophysics Data System (ADS)

Bergant, Marcos A.; Yawny, Alejandro A.; Perez Ipiña, Juan E.

2017-04-01

The structural integrity of steam generator tubes is a relevant issue concerning nuclear plant safety. In the present work, J-resistance curves of Inconel 690 and Incoloy 800 nuclear steam generator tubes with circumferential and longitudinal through wall cracks were obtained at room temperature and 300 °C using recently developed non-standard specimens' geometries. It was found that Incoloy 800 tubes exhibited higher J-resistance curves than Inconel 690 for both crack orientations. For both materials, circumferential cracks resulted into higher fracture resistance than longitudinal cracks, indicating a certain degree of texture anisotropy introduced by the tube fabrication process. From a practical point of view, temperature effects have found to be negligible in all cases. The results obtained in the present work provide a general framework for further application to structural integrity assessments of cracked tubes in a variety of nuclear steam generator designs.

Arbitrary Lagrangian-Eulerian Method with Local Structured Adaptive Mesh Refinement for Modeling Shock Hydrodynamics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, R W; Pember, R B; Elliott, N S

2001-10-22

A new method that combines staggered grid Arbitrary Lagrangian-Eulerian (ALE) techniques with structured local adaptive mesh refinement (AMR) has been developed for solution of the Euler equations. This method facilitates the solution of problems currently at and beyond the boundary of soluble problems by traditional ALE methods by focusing computational resources where they are required through dynamic adaption. Many of the core issues involved in the development of the combined ALEAMR method hinge upon the integration of AMR with a staggered grid Lagrangian integration method. The novel components of the method are mainly driven by the need to reconcile traditionalmore » AMR techniques, which are typically employed on stationary meshes with cell-centered quantities, with the staggered grids and grid motion employed by Lagrangian methods. Numerical examples are presented which demonstrate the accuracy and efficiency of the method.« less

Knowledge and attitudes towards disability in Moldova: A qualitative study of young people's views.

PubMed

McLean, Kenneth A; Hardie, Samantha; Paul, Abigail; Paul, Gary; Savage, Iain; Shields, Paul; Symes, Rebecca; Wilson, Joanna; Winstanley, Catherine; Harden, Jeni

2017-10-01

People with disabilities in the Republic of Moldova continue to experience considerable discrimination and social exclusion. The Moldovan government recently affirmed their commitment to promote community integration. However, there remains limited evidence to facilitate understanding of these issues, and barriers to the integrative process. This study explored the knowledge and attitudes towards disability of young people within Moldova. A qualitative approach was adopted and 3 semi-structured focus group interviews were conducted with schoolchildren (n = 12), aged 13-15 years. These interviews focussed on different aspects of disability, and community integration. Pictorial and written vignettes were used to stimulate discussion. The interviews were conducted and recorded in Romanian, and were subsequently translated into English to facilitate thematic data analysis. Identified themes included: (1) Knowledge and understanding of disability. The young people's knowledge was limited and framed by the medical model of disability; (2) Attitudes towards community integration. A bias against long-term care institutions, but differing views regarding integration; (3) Perceptions of barriers to community integration: (i) Cultural barriers. Negative, even hostile attitudes towards disability; (ii) Policy barriers. Poor support services; and (iii) Physical barriers. Ongoing issues regarding accessibility. People with disabilities in Moldova experience negative cultural attitudes linked to an outdated conception of disability itself. There are inadequate community support services and infrastructure which act as barriers to inclusion. At present, there can be limited interaction and participation of people with disabilities within local communities, and so few opportunities to refute persistent stereotypes and stigma surrounding disability. Copyright © 2017 Elsevier Inc. All rights reserved.

Integrated Seismological Network of Brazil: Key developments in technology.

NASA Astrophysics Data System (ADS)

Pirchiner, Marlon; Assumpção, Marcelo; Ferreira, Joaquim; França, George

2010-05-01

The Integrated Seismological Network of Brazil - BRASIS - will integrate the main Brazilian seismology groups in an extensive permanent broadband network with a (near) real-time acquisition system and automatic preliminary processing of epicenters and magnitudes. About 60 stations will cover the whole country to continuously monitor the seismic activity. Most stations will be operating by the end of 2010. Data will be received from remote stations at each research group and redistributed to all other groups. In addition to issuing a national catalog of earthquakes, each institution will make its own analysis and issue their own bulletins taking into account local and regional lithospheric structure. We chose the SEED format, seedlink and SeisComP as standard data format, exchange protocol and software framework for the network management, respectively. All different existing equipment (eg, Guralp/Scream, Geotech/CD1.1, RefTek/RTP, Quanterra/seedlink) will be integrated into the same system. We plan to provide: 1) improved station management through remote control, and indexes for quality control of acquired data, sending alerts to operators in critical cases. 2) automatic processing: picking, location with local and regional models and determination of magnitudes, issuing newsletters and alerts. 3) maintainence of an earthquakes catalog, and a waveforms database. 4) query tools and access to metadata, catalogs and waveform available to all researchers. In addition, the catalog of earthquakes and other seismological data will be available as layers in a Spatial Data Infrastructure with open source standards, providing new analysis capabilities to all geoscientists. Seiscomp3 has already been installed in two centers (UFRN and USP) with successful tests of Q330, Guralp, RefTek and Geotech plug-ins to the seedlink protocol. We will discuss the main difficulties of our project and the solutions adopted to improve the Brazilian seismological infrastructure.

The full spectrum of ethical issues in dementia care: systematic qualitative review.

PubMed

Strech, Daniel; Mertz, Marcel; Knüppel, Hannes; Neitzke, Gerald; Schmidhuber, Martina

2013-06-01

Integrating ethical issues in dementia-specific training material, clinical guidelines and national strategy plans requires an unbiased awareness of all the relevant ethical issues. To determine systematically and transparently the full spectrum of ethical issues in clinical dementia care. We conducted a systematic review in Medline (restricted to English and German literature published between 2000 and 2011) and Google books (with no restrictions). We applied qualitative text analysis and normative analysis to categorise the spectrum of ethical issues in clinical dementia care. The literature review retrieved 92 references that together mentioned a spectrum of 56 ethical issues in clinical dementia care. The spectrum was structured into seven major categories that consist of first- and second-order categories for ethical issues. The systematically derived spectrum of ethical issues in clinical dementia care presented in this paper can be used as training material for healthcare professionals, students and the public for raising awareness and understanding of the complexity of ethical issues in dementia care. It can also be used to identify ethical issues that should be addressed in dementia-specific training programmes, national strategy plans and clinical practice guidelines. Further research should evaluate whether this new genre of systematic reviews can be applied to the identification of ethical issues in other cognitive and somatic diseases. Also, the practical challenges in addressing ethical issues in training material, guidelines and policies need to be evaluated.

Integrating sentiment and social structure to determine preference alignments: the Irish Marriage Referendum

PubMed Central

O’Sullivan, David J. P.; Garduño-Hernández, Guillermo; Gleeson, James P.

2017-01-01

We examine the relationship between social structure and sentiment through the analysis of a large collection of tweets about the Irish Marriage Referendum of 2015. We obtain the sentiment of every tweet with the hashtags #marref and #marriageref that was posted in the days leading to the referendum, and construct networks to aggregate sentiment and use it to study the interactions among users. Our analysis shows that the sentiment of outgoing mention tweets is correlated with the sentiment of incoming mentions, and there are significantly more connections between users with similar sentiment scores than among users with opposite scores in the mention and follower networks. We combine the community structure of the follower and mention networks with the activity level of the users and sentiment scores to find groups that support voting ‘yes’ or ‘no’ in the referendum. There were numerous conversations between users on opposing sides of the debate in the absence of follower connections, which suggests that there were efforts by some users to establish dialogue and debate across ideological divisions. Our analysis shows that social structure can be integrated successfully with sentiment to analyse and understand the disposition of social media users around controversial or polarizing issues. These results have potential applications in the integration of data and metadata to study opinion dynamics, public opinion modelling and polling. PMID:28791141

Women supporting patients, men curing cancer: gender-related variations among Israeli Arab practitioners of traditional medicine in their treatment of patients with cancer.

PubMed

Popper-Giveon, Ariela; Schiff, Elad; Samuels, Noah; Ben-Arye, Eran

2015-06-01

The use of complementary traditional medicine (CTM) is prevalent among patients with cancer. An understanding of cultural and religious values is needed to design an effective patient-centered supportive treatment program. To examine gender-related demographic and professional characteristics; treatment goals and approaches; and attitudes toward integration among Arab practitioners of CTM. Male and female Arab CTM practitioners treating patients with cancer were located by snowballing through practitioner and clientele networks. Participants underwent semi-structured, in-depth interviews which were analyzed thematically, with a focus on gender-related issues. A total of 27 Arab CTM practitioners participated in the study (17 males, 10 females). Female practitioners were found to be treating women exclusively, with male practitioners treating both genders. Female practitioners tend to be younger, unmarried, urban-based and non-Muslim. Male practitioners set out to "cure" the cancer, while female practitioners focus on symptoms and quality of life. Male practitioners employ a more schematic and structured therapeutic approach; female practitioners a more eclectic and practical one. Male practitioners employ a collectivist approach, involving family members, while female practitioners interact exclusively with the patient. Finally, male CTM practitioners see integration as a means for recognition, increasing their power base. In contrast, female practitioners perceive integration as a foothold in fields from which they have previously been shut out. A number of gender-related issues can have a significant impact on CTM therapy among Arab patients. Further research is needed in order to understand the implications of these differences.

Control of optical systems

NASA Technical Reports Server (NTRS)

Founds, D.

1988-01-01

Some of the current and planned activities at the Air Force Systems Command in structures and controls for optical-type systems are summarized. Many of the activities are contracted to industry; one task is an in-house program which includes a hardware test program. The objective of the in-house program, referred to as the Aluminum Beam Expander Structure (ABES), is to address issues involved in on-orbit system identification. The structure, which appears similar to the LDR backup structure, is about 35 feet tall. The activity to date has been limited to acquisition of about 250 hours of test data. About 30 hours of data per excitation force is gathered in order to obtain sufficient data for a good statistical estimate of the structural parameters. The development of an Integrated Structural Modeling (ISM) computer program is being done by Boeing Aerospace Company. The objective of the contracted effort is to develop a combined optics, structures, thermal, controls, and multibody dynamics simulation code.

Control of flexible structures

NASA Technical Reports Server (NTRS)

Russell, R. A.

1985-01-01

The requirements for future space missions indicate that many of these spacecraft will be large, flexible, and in some applications, require precision geometries. A technology program that addresses the issues associated with the structure/control interactions for these classes of spacecraft is discussed. The goal of the NASA control of flexible structures technology program is to generate a technology data base that will provide the designer with options and approaches to achieve spacecraft performance such as maintaining geometry and/or suppressing undesired spacecraft dynamics. This technology program will define the appropriate combination of analysis, ground testing, and flight testing required to validate the structural/controls analysis and design tools. This work was motivated by a recognition that large minimum weight space structures will be required for many future missions. The tools necessary to support such design included: (1) improved structural analysis; (2) modern control theory; (3) advanced modeling techniques; (4) system identification; and (5) the integration of structures and controls.

Automated real-time structure health monitoring via signature pattern recognition

NASA Astrophysics Data System (ADS)

Sun, Fanping P.; Chaudhry, Zaffir A.; Rogers, Craig A.; Majmundar, M.; Liang, Chen

1995-05-01

Described in this paper are the details of an automated real-time structure health monitoring system. The system is based on structural signature pattern recognition. It uses an array of piezoceramic patches bonded to the structure as integrated sensor-actuators, an electric impedance analyzer for structural frequency response function acquisition and a PC for control and graphic display. An assembled 3-bay truss structure is employed as a test bed. Two issues, the localization of sensing area and the sensor temperature drift, which are critical for the success of this technique are addressed and a novel approach of providing temperature compensation using probability correlation function is presented. Due to the negligible weight and size of the solid-state sensor array and its ability to sense incipient-type damage, the system can eventually be implemented on many types of structures such as aircraft, spacecraft, large-span dome roof and steel bridges requiring multilocation and real-time health monitoring.

Women in the US Army. An Annotated Bibliography

DTIC Science & Technology

2002-05-13

females (Mottern et al, 1997). The study focused on six issues : (1) entry-level physical condition, (2) how gender -integrated training was affecting ...research. This Special Report summarizes ARI’s research on gender issues and provides an annotated bibliography of other research and studies that have been...various issues related to women in the Army, specifically, the integration and utilization of women, gender integration of basic training, and attitudes and

49 CFR 192.933 - What actions must be taken to address integrity issues?

Code of Federal Regulations, 2011 CFR

2011-10-01

... Transmission Pipeline Integrity Management § 192.933 What actions must be taken to address integrity issues? (a... any indication of metal loss, cracking or a stress riser. (iii) An indication or anomaly that in the...

49 CFR 192.933 - What actions must be taken to address integrity issues?

Code of Federal Regulations, 2013 CFR

2013-10-01

... Transmission Pipeline Integrity Management § 192.933 What actions must be taken to address integrity issues? (a... any indication of metal loss, cracking or a stress riser. (iii) An indication or anomaly that in the...

49 CFR 192.933 - What actions must be taken to address integrity issues?

Code of Federal Regulations, 2012 CFR

2012-10-01

... Transmission Pipeline Integrity Management § 192.933 What actions must be taken to address integrity issues? (a... any indication of metal loss, cracking or a stress riser. (iii) An indication or anomaly that in the...

A Concept for the Use and Integration of Super-Conducting Magnets in Structural Systems in General and Maglev Guideway Mega-Structures in Particular

NASA Technical Reports Server (NTRS)

Ussery, Wilfred T.; MacCalla, Eric; MacCalla, Johnetta; Elnimeiri, Mahjoub; Goldsmith, Myron; Polk, Sharon Madison; Jenkins, Mozella; Bragg, Robert H.

1996-01-01

Recent breakthroughs in several different fields now make it possible to incorporate the use of superconducting magnets in structures in ways which enhance the performance of structural members or components of structural systems in general and Maglev guideway mega-structures in particular. The building of structural systems which connect appropriately scaled superconducting magnets with the post-tensioned tensile components of beams, girders, or columns would, if coupled with 'state of the art' structure monitoring, feedback and control systems, and advanced computer software, constitute a distinct new generation of structures that would possess the unique characteristic of being heuristic and demand or live-load responsive. The holistic integration of powerful superconducting magnets in structures so that they do actual structural work, creates a class of 'technologically endowed' structures that, in part - literally substitute superconductive electric power and magnetism for concrete and steel. The research and development engineering, and architectural design issues associated with such 'technologically endowed' structural system can now be conceptualized, designed, computer simulates built and tested. The Maglev guideway mega-structure delineated herein incorporates these concepts, and is designed for operation in the median strip of U.S. Interstate Highway 5 from San Diego to Seattle an Vancouver, and possibly on to Fairbanks, Alaska. This system also fits in the median strip of U.S. Interstate Highway 55 and 95 North-South, and 80 and 10, East-West. As a Western Region 'Peace Dividend' project, it could become a National or Bi-National research, design and build, super turnkey project that would create thousands of jobs by applying superconducting, material science, electronic aerospace and other defense industry technologies to a multi-vehicle, multi-use Maglev guideway megastructure that integrates urban mass transit Lower Speed (0-100 mph), High Speed (100-200 mph), Super Speed (200-400 mph), and Hypersonic evacuated tube (400-10,000 mph) Maglev systems.

Building an Ontology for Identity Resolution in Healthcare and Public Health.

PubMed

Duncan, Jeffrey; Eilbeck, Karen; Narus, Scott P; Clyde, Stephen; Thornton, Sidney; Staes, Catherine

2015-01-01

Integration of disparate information from electronic health records, clinical data warehouses, birth certificate registries and other public health information systems offers great potential for clinical care, public health practice, and research. Such integration, however, depends on correctly matching patient-specific records using demographic identifiers. Without standards for these identifiers, record linkage is complicated by issues of structural and semantic heterogeneity. Our objectives were to develop and validate an ontology to: 1) identify components of identity and events subsequent to birth that result in creation, change, or sharing of identity information; 2) develop an ontology to facilitate data integration from multiple healthcare and public health sources; and 3) validate the ontology's ability to model identity-changing events over time. We interviewed domain experts in area hospitals and public health programs and developed process models describing the creation and transmission of identity information among various organizations for activities subsequent to a birth event. We searched for existing relevant ontologies. We validated the content of our ontology with simulated identity information conforming to scenarios identified in our process models. We chose the Simple Event Model (SEM) to describe events in early childhood and integrated the Clinical Element Model (CEM) for demographic information. We demonstrated the ability of the combined SEM-CEM ontology to model identity events over time. The use of an ontology can overcome issues of semantic and syntactic heterogeneity to facilitate record linkage.

Review of computer simulations of isotope effects on biochemical reactions: From the Bigeleisen equation to Feynman's path integral.

PubMed

Wong, Kin-Yiu; Xu, Yuqing; Xu, Liang

2015-11-01

Enzymatic reactions are integral components in many biological functions and malfunctions. The iconic structure of each reaction path for elucidating the reaction mechanism in details is the molecular structure of the rate-limiting transition state (RLTS). But RLTS is very hard to get caught or to get visualized by experimentalists. In spite of the lack of explicit molecular structure of the RLTS in experiment, we still can trace out the RLTS unique "fingerprints" by measuring the isotope effects on the reaction rate. This set of "fingerprints" is considered as a most direct probe of RLTS. By contrast, for computer simulations, oftentimes molecular structures of a number of TS can be precisely visualized on computer screen, however, theoreticians are not sure which TS is the actual rate-limiting one. As a result, this is an excellent stage setting for a perfect "marriage" between experiment and theory for determining the structure of RLTS, along with the reaction mechanism, i.e., experimentalists are responsible for "fingerprinting", whereas theoreticians are responsible for providing candidates that match the "fingerprints". In this Review, the origin of isotope effects on a chemical reaction is discussed from the perspectives of classical and quantum worlds, respectively (e.g., the origins of the inverse kinetic isotope effects and all the equilibrium isotope effects are purely from quantum). The conventional Bigeleisen equation for isotope effect calculations, as well as its refined version in the framework of Feynman's path integral and Kleinert's variational perturbation (KP) theory for systematically incorporating anharmonicity and (non-parabolic) quantum tunneling, are also presented. In addition, the outstanding interplay between theory and experiment for successfully deducing the RLTS structures and the reaction mechanisms is demonstrated by applications on biochemical reactions, namely models of bacterial squalene-to-hopene polycyclization and RNA 2'-O-transphosphorylation. For all these applications, we used our recently-developed path-integral method based on the KP theory, called automated integration-free path-integral (AIF-PI) method, to perform ab initio path-integral calculations of isotope effects. As opposed to the conventional path-integral molecular dynamics (PIMD) and Monte Carlo (PIMC) simulations, values calculated from our AIF-PI path-integral method can be as precise as (not as accurate as) the numerical precision of the computing machine. Lastly, comments are made on the general challenges in theoretical modeling of candidates matching the experimental "fingerprints" of RLTS. This article is part of a Special Issue entitled: Enzyme Transition States from Theory and Experiment. Copyright © 2015 Elsevier B.V. All rights reserved.

Inconsistencies in the Roles of Family- and Paid- Carers in Monitoring Health Issues in People with Learning Disabilities: Some Implications for the Integration of Health and Social Care

ERIC Educational Resources Information Center

Willis, Diane S.

2015-01-01

Changes in the living circumstances of people with learning disabilities have seen responsibility for their health become the provenance of paid-and family-carers. Thirteen semi-structured interviews were conducted with three family-carers and ten paid-carers. Findings revealed that the role of these carers was undefined, leading to difficulty in…

Unpacking vertical and horizontal integration: childhood overweight/obesity programs and planning, a Canadian perspective

PubMed Central

2010-01-01

Background Increasingly, multiple intervention programming is being understood and implemented as a key approach to developing public health initiatives and strategies. Using socio-ecological and population health perspectives, multiple intervention programming approaches are aimed at providing coordinated and strategic comprehensive programs operating over system levels and across sectors, allowing practitioners and decision makers to take advantage of synergistic effects. These approaches also require vertical and horizontal (v/h) integration of policy and practice in order to be maximally effective. Discussion This paper examines v/h integration of interventions for childhood overweight/obesity prevention and reduction from a Canadian perspective. It describes the implications of v/h integration for childhood overweight and obesity prevention, with examples of interventions where v/h integration has been implemented. An application of a conceptual framework for structuring v/h integration of an overweight/obesity prevention initiative is presented. The paper concludes with a discussion of the implications of vertical/horizontal integration for policy, research, and practice related to childhood overweight and obesity prevention multiple intervention programs. Summary Both v/h integration across sectors and over system levels are needed to fully support multiple intervention programs of the complexity and scope required by obesity issues. V/h integration requires attention to system structures and processes. A conceptual framework is needed to support policy alignment, multi-level evaluation, and ongoing coordination of people at the front lines of practice. Using such tools to achieve integration may enhance sustainability, increase effectiveness of prevention and reduction efforts, decrease stigmatization, and lead to new ways to relate the environment to people and people to the environment for better health for children. PMID:20478054

Unpacking vertical and horizontal integration: childhood overweight/obesity programs and planning, a Canadian perspective.

PubMed

Maclean, Lynne M; Clinton, Kathryn; Edwards, Nancy; Garrard, Michael; Ashley, Lisa; Hansen-Ketchum, Patti; Walsh, Audrey

2010-05-17

Increasingly, multiple intervention programming is being understood and implemented as a key approach to developing public health initiatives and strategies. Using socio-ecological and population health perspectives, multiple intervention programming approaches are aimed at providing coordinated and strategic comprehensive programs operating over system levels and across sectors, allowing practitioners and decision makers to take advantage of synergistic effects. These approaches also require vertical and horizontal (v/h) integration of policy and practice in order to be maximally effective. This paper examines v/h integration of interventions for childhood overweight/obesity prevention and reduction from a Canadian perspective. It describes the implications of v/h integration for childhood overweight and obesity prevention, with examples of interventions where v/h integration has been implemented. An application of a conceptual framework for structuring v/h integration of an overweight/obesity prevention initiative is presented. The paper concludes with a discussion of the implications of vertical/horizontal integration for policy, research, and practice related to childhood overweight and obesity prevention multiple intervention programs. Both v/h integration across sectors and over system levels are needed to fully support multiple intervention programs of the complexity and scope required by obesity issues. V/h integration requires attention to system structures and processes. A conceptual framework is needed to support policy alignment, multi-level evaluation, and ongoing coordination of people at the front lines of practice. Using such tools to achieve integration may enhance sustainability, increase effectiveness of prevention and reduction efforts, decrease stigmatization, and lead to new ways to relate the environment to people and people to the environment for better health for children.

Multiphysics Engineering Analysis for an Integrated Design of ITER Diagnostic First Wall and Diagnostic Shield Module Design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhai, Y.; Loesser, G.; Smith, M.

ITER diagnostic first walls (DFWs) and diagnostic shield modules (DSMs) inside the port plugs (PPs) are designed to protect diagnostic instrument and components from a harsh plasma environment and provide structural support while allowing for diagnostic access to the plasma. The design of DFWs and DSMs are driven by 1) plasma radiation and nuclear heating during normal operation 2) electromagnetic loads during plasma events and associate component structural responses. A multi-physics engineering analysis protocol for the design has been established at Princeton Plasma Physics Laboratory and it was used for the design of ITER DFWs and DSMs. The analyses weremore » performed to address challenging design issues based on resultant stresses and deflections of the DFW-DSM-PP assembly for the main load cases. ITER Structural Design Criteria for In-Vessel Components (SDC-IC) required for design by analysis and three major issues driving the mechanical design of ITER DFWs are discussed. The general guidelines for the DSM design have been established as a result of design parametric studies.« less

Current Issues for Higher Education Information Resources Management.

ERIC Educational Resources Information Center

CAUSE/EFFECT, 1996

1996-01-01

Issues identified as important to the future of information resources management and use in higher education include information policy in a networked environment, distributed computing, integrating information resources and college planning, benchmarking information technology, integrated digital libraries, technology integration in teaching,…

Susceptibility to mountain hazards in Austria - paradigms of vulnerability revisited

NASA Astrophysics Data System (ADS)

Fuchs, Sven

2010-05-01

The concept of vulnerability is pillared by multiple disciplinary theories underpinning either a technical or a social origin of the concept and resulting in a range of paradigms for either a qualitative or quantitative assessment of vulnerability. However, efforts to reduce susceptibility to hazards and to create disaster-resilient communities require intersections among these theories, since human activity cannot be seen independently from the environmental setting. Acknowledging different roots of disciplinary paradigms, issues determining structural, economic, institutional and social vulnerability are discussed with respect to mountain hazards in Austria. The underlying idea of taking such an integrative viewpoint was the cognition that human action in mountain environments affects the state of vulnerability, and the state of vulnerability in turn shapes the possibilities of human action. It is argued that structural vulnerability as originator results in considerable economic vulnerability, generated by the institutional settings of dealing with natural hazards and shaped by the overall societal framework. Hence, the vulnerability of a specific location and within a considered point of time is triggered by the hazardous event and the related physical susceptibility of structures, such as buildings located on a torrent fan. Depending on the specific institutional settings, economic vulnerability of individuals or of the society results, above all with respect to imperfect loss compensation mechanisms in the areas under investigation. While this potential for harm can be addressed as social vulnerability, the concept of institutional vulnerability has been developed with respect to the overall political settings of governmental risk management. As a result, the concept of vulnerability, as being used in natural sciences, can be extended by integration of possible reasons why such physical susceptibility of structures exists, and by integration of compensation mechanisms and coping strategies being developed within social sciences. If vulnerability and its counterpart, resilience, is analysed and evaluated by using a comprehensive approach, a better understanding of the vulnerability-influencing parameters could be achieved, taking into account the interdependencies and interactions between the disciplinary foci. Thereby the overall aim of this work is not to develop another integrative approach for vulnerability assessment, different approaches are rather applied by using a vulnerability-of-place criterion, and key issues of vulnerability are reconsidered aiming at a general illustration of the situation in a densely populated mountain region of Europe.

Nonlinear Shell Modeling of Thin Membranes with Emphasis on Structural Wrinkling

NASA Technical Reports Server (NTRS)

Tessler, Alexander; Sleight, David W.; Wang, John T.

2003-01-01

Thin solar sail membranes of very large span are being envisioned for near-term space missions. One major design issue that is inherent to these very flexible structures is the formation of wrinkling patterns. Structural wrinkles may deteriorate a solar sail's performance and, in certain cases, structural integrity. In this paper, a geometrically nonlinear, updated Lagrangian shell formulation is employed using the ABAQUS finite element code to simulate the formation of wrinkled deformations in thin-film membranes. The restrictive assumptions of true membranes, i.e. Tension Field theory (TF), are not invoked. Two effective modeling strategies are introduced to facilitate convergent solutions of wrinkled equilibrium states. Several numerical studies are carried out, and the results are compared with recent experimental data. Good agreement is observed between the numerical simulations and experimental data.

Control and structural optimization for maneuvering large spacecraft

NASA Technical Reports Server (NTRS)

Chun, H. M.; Turner, J. D.; Yu, C. C.

1990-01-01

Presented here are the results of an advanced control design as well as a discussion of the requirements for automating both the structures and control design efforts for maneuvering a large spacecraft. The advanced control application addresses a general three dimensional slewing problem, and is applied to a large geostationary platform. The platform consists of two flexible antennas attached to the ends of a flexible truss. The control strategy involves an open-loop rigid body control profile which is derived from a nonlinear optimal control problem and provides the main control effort. A perturbation feedback control reduces the response due to the flexibility of the structure. Results are shown which demonstrate the usefulness of the approach. Software issues are considered for developing an integrated structures and control design environment.

Healing the incest wound: a treatment update with attention to recovered-memory issues.

PubMed

Courtois, C A

1997-01-01

This article provides an updated treatment model for adults who report having experienced incestuous abuse in childhood. It integrates psychodynamic, traumatic stress, developmental and feminist formulations, accords greater emphasis to object relations and self-psychology perspectives, includes more attention to dissociative reactions, and utilizes more cognitive-behavioral interventions. It is also responsive to issues raised in the recovered/false memory controversy. This holistic model is sequenced, paced, and titrated according to the patient's characterological structure, ego strength, and needs as well as the range and severity of presenting problems and life difficulties. Special consideration is given to issues pertaining to memory and the maintenance of a neutral stance by the therapist, especially in the case of recovered rather than continuous memories and/or suspicions rather than actual knowledge of abuse. Contemporary perspectives regarding some of the unique transference, countertransference, and vicarious traumatization issues with this population and their potential impact on treatment are also discussed.

Research enrichment: evaluation of structured research in the curriculum for dental medicine students as part of the vertical and horizontal integration of biomedical training and discovery

PubMed Central

Kingsley, Karl; O'Malley, Susan; Stewart, Tanis; Howard, Katherine M

2008-01-01

Background Research programs within medical and dental schools are important vehicles for biomedical and clinical discovery, serving as effective teaching and learning tools by providing situations in which predoctoral students develop problem-solving and critical-thinking skills. Although research programs at many medical and dental schools are well-established, they may not be well integrated into the predoctoral curriculum to effectively support the learning objectives for their students. Methods A series of structured seminars, incorporating faculty research, was designed for first-year dental students at the University of Nevada, Las Vegas, School of Dental Medicine to reinforce and support the concepts and skills taught in concurrent courses. A structured research enrichment period was also created to facilitate student engagement in active research using faculty and student curricular release time. Course evaluations and surveys were administered to gauge student perceptions of the curricular integration of research, the impact of these seminars on recruitment to the research program, and overall levels of student satisfaction with research enrichment. Results The analysis of course surveys revealed that students perceived the research-containing seminars effectively illustrated concepts, were logically sequenced, and were well-integrated into their curriculum. In addition, analysis of surveys revealed that the Integration Seminar courses motivated students to engage in research enrichment. Finally, this analysis provided evidence that students were very satisfied with their overall learning experience during research enrichment. Conclusion Curricular integration is one method of improving the teaching and learning of complicated and inter-related concepts, providing an opportunity to incorporate research training and objectives into traditionally separate didactic courses. Despite the benefits of curricular integration, finding the most appropriate points of integration, obtaining release time for curricular development and for research engagement, and funding predoctoral student research remain issues to be addressed in ways that reflect the character of the faculty and the goals of each institution. PMID:18284692

Research enrichment: evaluation of structured research in the curriculum for dental medicine students as part of the vertical and horizontal integration of biomedical training and discovery.

PubMed

Kingsley, Karl; O'Malley, Susan; Stewart, Tanis; Howard, Katherine M

2008-02-19

Research programs within medical and dental schools are important vehicles for biomedical and clinical discovery, serving as effective teaching and learning tools by providing situations in which predoctoral students develop problem-solving and critical-thinking skills. Although research programs at many medical and dental schools are well-established, they may not be well integrated into the predoctoral curriculum to effectively support the learning objectives for their students. A series of structured seminars, incorporating faculty research, was designed for first-year dental students at the University of Nevada, Las Vegas, School of Dental Medicine to reinforce and support the concepts and skills taught in concurrent courses. A structured research enrichment period was also created to facilitate student engagement in active research using faculty and student curricular release time. Course evaluations and surveys were administered to gauge student perceptions of the curricular integration of research, the impact of these seminars on recruitment to the research program, and overall levels of student satisfaction with research enrichment. The analysis of course surveys revealed that students perceived the research-containing seminars effectively illustrated concepts, were logically sequenced, and were well-integrated into their curriculum. In addition, analysis of surveys revealed that the Integration Seminar courses motivated students to engage in research enrichment. Finally, this analysis provided evidence that students were very satisfied with their overall learning experience during research enrichment. Curricular integration is one method of improving the teaching and learning of complicated and inter-related concepts, providing an opportunity to incorporate research training and objectives into traditionally separate didactic courses. Despite the benefits of curricular integration, finding the most appropriate points of integration, obtaining release time for curricular development and for research engagement, and funding predoctoral student research remain issues to be addressed in ways that reflect the character of the faculty and the goals of each institution.

FOREWORD: Structural Health Monitoring and Intelligent Infrastructure

NASA Astrophysics Data System (ADS)

Wu, Zhishen; Fujino, Yozo

2005-06-01

This special issue collects together 19 papers that were originally presented at the First International Conference on Structural Health Monitoring and Intelligent Infrastructure (SHMII-1'2003), held in Tokyo, Japan, on 13-15 November 2003. This conference was organized by the Japan Society of Civil Engineers (JSCE) with partial financial support from the Japan Society for the Promotion of Science (JSPS) and the Ministry of Education, Culture, Sport, Science and Technology, Japan. Many related organizations supported the conference. A total of 16 keynote papers including six state-of-the-art reports from different counties, six invited papers and 154 contributed papers were presented at the conference. The conference was attended by a diverse group of about 300 people from a variety of disciplines in academia, industry and government from all over the world. Structural health monitoring (SHM) and intelligent materials, structures and systems have been the subject of intense research and development in the last two decades and, in recent years, an increasing range of applications in infrastructure have been discovered both for existing structures and for new constructions. SHMII-1'2003 addressed progress in the development of building, transportation, marine, underground and energy-generating structures, and other civilian infrastructures that are periodically, continuously and/or actively monitored where there is a need to optimize their performance. In order to focus the current needs on SHM and intelligent technologies, the conference theme was set as 'Structures/Infrastructures Sustainability'. We are pleased to have the privilege to edit this special issue on SHM and intelligent infrastructure based on SHMII-1'2003. We invited some of the presenters to submit a revised/extended version of their paper that was included in the SHMII-1'2003 proceedings for possible publication in the special issue. Each paper included in this special issue was edited with the same quality standards as for any paper in a regular issue. The papers cover a wide spectrum of topics including smart and effective sensing technologies, reliable approaches to signal processing, rational data gathering and interpretation methods, advanced damage characterization, modeling feature selection and diagnosis methods, and system integration technologies, etc. This special issue contains the most up-to-date achievements in SHM and intelligent technologies and provides information pertaining to their current and potential applications in infrastructure. It is our hope that this special issue makes a significant contribution in advancing awareness and acceptance of SHM and intelligent technologies for the maintenance and construction of different kinds of infrastructure. We would like to express our sincere thanks to Professor Varadan (Editor-in-Chief), Professor Matsuzaki (Regional Editor), the Editorial Assistants and the staff at Institute of Physics Publishing for their great support and advice in publishing this special issue. Special thanks are due to all the reviewers for their willingness to share their time and expertise. Final but important thanks go to Ms Suzhen Li (Doctorate Candidate at Ibaraki University) for her assistance in editing this special issue.

Integrated Outdoor Education/Adventure. Feature Issue.

ERIC Educational Resources Information Center

Schleien, Stuart J., Ed.; And Others

1992-01-01

The 12 brief articles in this "feature" or theme issue describe successful approaches to development of outdoor education programs which successfully integrate individuals with and without disabilities. Titles and authors are: "Outdoor Education and Adventure: Challenges and Rewards for All" (Stuart J. Schleien); "Benefits of Integrated Outdoor…

Medial temporal lobe roles in human path integration.

PubMed

Yamamoto, Naohide; Philbeck, John W; Woods, Adam J; Gajewski, Daniel A; Arthur, Joeanna C; Potolicchio, Samuel J; Levy, Lucien; Caputy, Anthony J

2014-01-01

Path integration is a process in which observers derive their location by integrating self-motion signals along their locomotion trajectory. Although the medial temporal lobe (MTL) is thought to take part in path integration, the scope of its role for path integration remains unclear. To address this issue, we administered a variety of tasks involving path integration and other related processes to a group of neurosurgical patients whose MTL was unilaterally resected as therapy for epilepsy. These patients were unimpaired relative to neurologically intact controls in many tasks that required integration of various kinds of sensory self-motion information. However, the same patients (especially those who had lesions in the right hemisphere) walked farther than the controls when attempting to walk without vision to a previewed target. Importantly, this task was unique in our test battery in that it allowed participants to form a mental representation of the target location and anticipate their upcoming walking trajectory before they began moving. Thus, these results put forth a new idea that the role of MTL structures for human path integration may stem from their participation in predicting the consequences of one's locomotor actions. The strengths of this new theoretical viewpoint are discussed.

Medial Temporal Lobe Roles in Human Path Integration

PubMed Central

Yamamoto, Naohide; Philbeck, John W.; Woods, Adam J.; Gajewski, Daniel A.; Arthur, Joeanna C.; Potolicchio, Samuel J.; Levy, Lucien; Caputy, Anthony J.

2014-01-01

Path integration is a process in which observers derive their location by integrating self-motion signals along their locomotion trajectory. Although the medial temporal lobe (MTL) is thought to take part in path integration, the scope of its role for path integration remains unclear. To address this issue, we administered a variety of tasks involving path integration and other related processes to a group of neurosurgical patients whose MTL was unilaterally resected as therapy for epilepsy. These patients were unimpaired relative to neurologically intact controls in many tasks that required integration of various kinds of sensory self-motion information. However, the same patients (especially those who had lesions in the right hemisphere) walked farther than the controls when attempting to walk without vision to a previewed target. Importantly, this task was unique in our test battery in that it allowed participants to form a mental representation of the target location and anticipate their upcoming walking trajectory before they began moving. Thus, these results put forth a new idea that the role of MTL structures for human path integration may stem from their participation in predicting the consequences of one's locomotor actions. The strengths of this new theoretical viewpoint are discussed. PMID:24802000

A Semantic Grid Oriented to E-Tourism

NASA Astrophysics Data System (ADS)

Zhang, Xiao Ming

With increasing complexity of tourism business models and tasks, there is a clear need of the next generation e-Tourism infrastructure to support flexible automation, integration, computation, storage, and collaboration. Currently several enabling technologies such as semantic Web, Web service, agent and grid computing have been applied in the different e-Tourism applications, however there is no a unified framework to be able to integrate all of them. So this paper presents a promising e-Tourism framework based on emerging semantic grid, in which a number of key design issues are discussed including architecture, ontologies structure, semantic reconciliation, service and resource discovery, role based authorization and intelligent agent. The paper finally provides the implementation of the framework.

Stochastic simulation and robust design optimization of integrated photonic filters

NASA Astrophysics Data System (ADS)

Weng, Tsui-Wei; Melati, Daniele; Melloni, Andrea; Daniel, Luca

2017-01-01

Manufacturing variations are becoming an unavoidable issue in modern fabrication processes; therefore, it is crucial to be able to include stochastic uncertainties in the design phase. In this paper, integrated photonic coupled ring resonator filters are considered as an example of significant interest. The sparsity structure in photonic circuits is exploited to construct a sparse combined generalized polynomial chaos model, which is then used to analyze related statistics and perform robust design optimization. Simulation results show that the optimized circuits are more robust to fabrication process variations and achieve a reduction of 11%-35% in the mean square errors of the 3 dB bandwidth compared to unoptimized nominal designs.

[Offshore work and the work of nurses on board: an integrative review].

PubMed

Antoniolli, Silvana Aline Cordeiro; Emmel, Suzel Vaz; Ferreira, Gímerson Erick; Paz, Potiguara de Oliveira; Kaiser, Dagmar Elaine

2015-08-01

To know the production of theoretical approaches on issues related to offshore work and the work of offshore nurses. Integrative literature review conducted in the databases of LILACS, BDENF, MEDLINE, SciELO and Index PSI. We selected 33 studies published in national and international journals between 1997 and 2014. The thematic analysis corpus resulted in four central themes: offshore work environment; amid work adversities, an escape; structuring of offshore health and safety services; in search of safe practices. This study contributes to the offshore work of nurses in relation to the nature of work, acting amid adversities and the restless search for safe practices in the open sea.

Basic characteristics and realization of production system control

NASA Astrophysics Data System (ADS)

Cheng, Shaopeng; Shell, Richard; Hall, Ernest L.

1992-11-01

This paper analyzes the issues involved in developing an intelligent production control system. It describes the basic characteristics of a production control system and an effective design methodology to realize the production control functions. Petri net, subsystem and hierarchical control concepts are applied to a computer integrated material handling system (MHS). Some communication and interface requirements of the MHS are also considered in this paper. The control system solution is illustrated with an actual MHS operation case which indicates that a truly flexible and integrated production system can be realized with a Petri net operation model and a hierarchical control structure. The significance of this work is related to the different operation testing and evaluation requirements encountered in manufacturing.

Software Considerations for Subscale Flight Testing of Experimental Control Laws

NASA Technical Reports Server (NTRS)

Murch, Austin M.; Cox, David E.; Cunningham, Kevin

2009-01-01

The NASA AirSTAR system has been designed to address the challenges associated with safe and efficient subscale flight testing of research control laws in adverse flight conditions. In this paper, software elements of this system are described, with an emphasis on components which allow for rapid prototyping and deployment of aircraft control laws. Through model-based design and automatic coding a common code-base is used for desktop analysis, piloted simulation and real-time flight control. The flight control system provides the ability to rapidly integrate and test multiple research control laws and to emulate component or sensor failures. Integrated integrity monitoring systems provide aircraft structural load protection, isolate the system from control algorithm failures, and monitor the health of telemetry streams. Finally, issues associated with software configuration management and code modularity are briefly discussed.

Integrated primary health care: Finnish solutions and experiences

PubMed Central

Kokko, Simo

2009-01-01

Background Finland has since 1972 had a primary health care system based on health centres run and funded by the local public authorities called ‘municipalities’. On the world map of primary health care systems, the Finnish solution claims to be the most health centre oriented and also the widest, both in terms of the numbers of staff and also of different professions employed. Offering integrated care through multi-professional health centres has been overshadowed by exceptional difficulties in guaranteeing a reasonable access to the population at times when they need primary medical or dental services. Solutions to the problems of access have been found, but they do not seem durable. Description of policy practice During the past 10 years, the health centres have become a ground of active development structural change, for which no end is in sight. Broader issues of municipal and public administration structures are being solved through rearranging primary health services. In these rearrangements, integration with specialist services and with social services together with mergers of health centres and municipalities are occurring at an accelerated pace. This leads into fundamental questions of the benefits of integration, especially if extensive integration leads into the threat of the loss of identity for primary health care. Discussion This article ends with some lessons to be learned from the situation in Finland for other countries. PMID:19590612

Special issue on cluster algebras in mathematical physics

NASA Astrophysics Data System (ADS)

Di Francesco, Philippe; Gekhtman, Michael; Kuniba, Atsuo; Yamazaki, Masahito

2014-02-01

This is a call for contributions to a special issue of Journal of Physics A: Mathematical and Theoretical dedicated to cluster algebras in mathematical physics. Over the ten years since their introduction by Fomin and Zelevinsky, the theory of cluster algebras has witnessed a spectacular growth, first and foremost due to the many links that have been discovered with a wide range of subjects in mathematics and, increasingly, theoretical and mathematical physics. The main motivation of this special issue is to gather together reviews, recent developments and open problems, mainly from a mathematical physics viewpoint, into a single comprehensive issue. We expect that such a special issue will become a valuable reference for the broad scientific community working in mathematical and theoretical physics. The issue will consist of invited review articles and contributed papers containing new results on the interplays of cluster algebras with mathematical physics. Editorial policy The Guest Editors for this issue are Philippe Di Francesco, Michael Gekhtman, Atsuo Kuniba and Masahito Yamazaki. The areas and topics for this issue include, but are not limited to: discrete integrable systems arising from cluster mutations cluster structure on Poisson varieties cluster algebras and soliton interactions cluster positivity conjecture Y-systems in the thermodynamic Bethe ansatz and Zamolodchikov's periodicity conjecture T-system of transfer matrices of integrable lattice models dilogarithm identities in conformal field theory wall crossing in 4d N = 2 supersymmetric gauge theories 4d N = 1 quiver gauge theories described by networks scattering amplitudes of 4d N = 4 theories 3d N = 2 gauge theories described by flat connections on 3-manifolds integrability of dimer/Ising models on graphs. All contributions will be refereed and processed according to the usual procedure of the journal. Guidelines for preparation of contributions The deadline for contributed papers is 31 March 2014. This deadline will allow the special issue to appear at the end of 2014. There is no strict regulation on article size, but as a guide the preferable size is 15-30 pages for contributed papers and 40-60 pages for reviews. Further advice on publishing your work in Journal of Physics A may be found at iopscience.iop.org/jphysa. Contributions to the special issue should be submitted by web upload via ScholarOne Manuscripts, quoting 'JPhysA special issue on cluster algebras in mathematical physics'. Submissions should ideally be in standard LaTeX form. Please see the website for further information on electronic submissions. All contributions should be accompanied by a read-me file or covering letter giving the postal and e-mail addresses for correspondence. The Publishing Office should be notified of any subsequent change of address. The special issue will be published in the print and online versions of the journal.

Special issue on cluster algebras in mathematical physics

NASA Astrophysics Data System (ADS)

Di Francesco, Philippe; Gekhtman, Michael; Kuniba, Atsuo; Yamazaki, Masahito

2013-12-01

This is a call for contributions to a special issue of Journal of Physics A: Mathematical and Theoretical dedicated to cluster algebras in mathematical physics. Over the ten years since their introduction by Fomin and Zelevinsky, the theory of cluster algebras has witnessed a spectacular growth, first and foremost due to the many links that have been discovered with a wide range of subjects in mathematics and, increasingly, theoretical and mathematical physics. The main motivation of this special issue is to gather together reviews, recent developments and open problems, mainly from a mathematical physics viewpoint, into a single comprehensive issue. We expect that such a special issue will become a valuable reference for the broad scientific community working in mathematical and theoretical physics. The issue will consist of invited review articles and contributed papers containing new results on the interplays of cluster algebras with mathematical physics. Editorial policy The Guest Editors for this issue are Philippe Di Francesco, Michael Gekhtman, Atsuo Kuniba and Masahito Yamazaki. The areas and topics for this issue include, but are not limited to: discrete integrable systems arising from cluster mutations cluster structure on Poisson varieties cluster algebras and soliton interactions cluster positivity conjecture Y-systems in the thermodynamic Bethe ansatz and Zamolodchikov's periodicity conjecture T-system of transfer matrices of integrable lattice models dilogarithm identities in conformal field theory wall crossing in 4d N = 2 supersymmetric gauge theories 4d N = 1 quiver gauge theories described by networks scattering amplitudes of 4d N = 4 theories 3d N = 2 gauge theories described by flat connections on 3-manifolds integrability of dimer/Ising models on graphs. All contributions will be refereed and processed according to the usual procedure of the journal. Guidelines for preparation of contributions The deadline for contributed papers is 31 March 2014. This deadline will allow the special issue to appear at the end of 2014. There is no strict regulation on article size, but as a guide the preferable size is 15-30 pages for contributed papers and 40-60 pages for reviews. Further advice on publishing your work in Journal of Physics A may be found at iopscience.iop.org/jphysa. Contributions to the special issue should be submitted by web upload via ScholarOne Manuscripts, quoting 'JPhysA special issue on cluster algebras in mathematical physics'. Submissions should ideally be in standard LaTeX form. Please see the website for further information on electronic submissions. All contributions should be accompanied by a read-me file or covering letter giving the postal and e-mail addresses for correspondence. The Publishing Office should be notified of any subsequent change of address. The special issue will be published in the print and online versions of the journal.

Special issue on cluster algebras in mathematical physics

NASA Astrophysics Data System (ADS)

Di Francesco, Philippe; Gekhtman, Michael; Kuniba, Atsuo; Yamazaki, Masahito

2013-11-01

This is a call for contributions to a special issue of Journal of Physics A: Mathematical and Theoretical dedicated to cluster algebras in mathematical physics. Over the ten years since their introduction by Fomin and Zelevinsky, the theory of cluster algebras has witnessed a spectacular growth, first and foremost due to the many links that have been discovered with a wide range of subjects in mathematics and, increasingly, theoretical and mathematical physics. The main motivation of this special issue is to gather together reviews, recent developments and open problems, mainly from a mathematical physics viewpoint, into a single comprehensive issue. We expect that such a special issue will become a valuable reference for the broad scientific community working in mathematical and theoretical physics. The issue will consist of invited review articles and contributed papers containing new results on the interplays of cluster algebras with mathematical physics. Editorial policy The Guest Editors for this issue are Philippe Di Francesco, Michael Gekhtman, Atsuo Kuniba and Masahito Yamazaki. The areas and topics for this issue include, but are not limited to: discrete integrable systems arising from cluster mutations cluster structure on Poisson varieties cluster algebras and soliton interactions cluster positivity conjecture Y-systems in the thermodynamic Bethe ansatz and Zamolodchikov's periodicity conjecture T-system of transfer matrices of integrable lattice models dilogarithm identities in conformal field theory wall crossing in 4d N = 2 supersymmetric gauge theories 4d N = 1 quiver gauge theories described by networks scattering amplitudes of 4d N = 4 theories 3d N = 2 gauge theories described by flat connections on 3-manifolds integrability of dimer/Ising models on graphs. All contributions will be refereed and processed according to the usual procedure of the journal. Guidelines for preparation of contributions The deadline for contributed papers is 31 March 2014. This deadline will allow the special issue to appear at the end of 2014. There is no strict regulation on article size, but as a guide the preferable size is 15-30 pages for contributed papers and 40-60 pages for reviews. Further advice on publishing your work in Journal of Physics A may be found at iopscience.iop.org/jphysa. Contributions to the special issue should be submitted by web upload via ScholarOne Manuscripts, quoting 'JPhysA special issue on cluster algebras in mathematical physics'. Submissions should ideally be in standard LaTeX form. Please see the website for further information on electronic submissions. All contributions should be accompanied by a read-me file or covering letter giving the postal and e-mail addresses for correspondence. The Publishing Office should be notified of any subsequent change of address. The special issue will be published in the print and online versions of the journal.

49 CFR 192.933 - What actions must be taken to address integrity issues?

Code of Federal Regulations, 2010 CFR

2010-10-01

...) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Gas Transmission Pipeline Integrity Management § 192.933 What actions must be taken to address integrity issues? (a...

A Pedagogical Strategy for Teaching Human Development: Dyadic Essay Confrontations through Writing and Discussion.

ERIC Educational Resources Information Center

Sherman, Lawrence W.

This paper integrates several contemporary issues, all of which focus on the teaching of human developmental theories. These issues include postmodern thought, higher level thinking processes, introducting conceptual conflict and arousal, motivation, and integrating the writing process into the psychology curriculum. Each issue is briefly…

Integrated monitoring of wind plant systems

NASA Astrophysics Data System (ADS)

Whelan, Matthew J.; Janoyan, Kerop D.; Qiu, Tong

2008-03-01

Wind power is a renewable source of energy that is quickly gaining acceptance by many. Advanced sensor technologies have currently focused solely on improving wind turbine rotor aerodynamics and increasing of the efficiency of the blade design and concentration. Alternatively, potential improvements in wind plant efficiency may be realized through reduction of reactionary losses of kinetic energy to the structural and substructural systems supporting the turbine mechanics. Investigation of the complete dynamic structural response of the wind plant is proposed using a large-scale, high-rate wireless sensor network. The wireless network enables sensors to be placed across the sizable structure, including the rotating blades, without consideration of cabling issues and the economic burden associated with large spools of measurement cables. A large array of multi-axis accelerometers is utilized to evaluate the modal properties of the system as well as individual members and would enable long-term structural condition monitoring of the wind turbine as well. Additionally, environmental parameters, including wind speed, temperature, and humidity, are wirelessly collected for correlation. Such a wireless system could be integrated with electrical monitoring sensors and actuators and incorporated into a remote multi-turbine centralized plant monitoring and control system.

Using kaizen to improve employee well-being: Results from two organizational intervention studies.

PubMed

von Thiele Schwarz, Ulrica; Nielsen, Karina M; Stenfors-Hayes, Terese; Hasson, Henna

2017-08-01

Participatory intervention approaches that are embedded in existing organizational structures may improve the efficiency and effectiveness of organizational interventions, but concrete tools are lacking. In the present article, we use a realist evaluation approach to explore the role of kaizen, a lean tool for participatory continuous improvement, in improving employee well-being in two cluster-randomized, controlled participatory intervention studies. Case 1 is from the Danish Postal Service, where kaizen boards were used to implement action plans. The results of multi-group structural equation modeling showed that kaizen served as a mechanism that increased the level of awareness of and capacity to manage psychosocial issues, which, in turn, predicted increased job satisfaction and mental health. Case 2 is from a regional hospital in Sweden that integrated occupational health processes with a pre-existing kaizen system. Multi-group structural equation modeling revealed that, in the intervention group, kaizen work predicted better integration of organizational and employee objectives after 12 months, which, in turn, predicted increased job satisfaction and decreased discomfort at 24 months. The findings suggest that participatory and structured problem-solving approaches that are familiar and visual to employees can facilitate organizational interventions.

Using kaizen to improve employee well-being: Results from two organizational intervention studies

PubMed Central

von Thiele Schwarz, Ulrica; Nielsen, Karina M; Stenfors-Hayes, Terese; Hasson, Henna

2016-01-01

Participatory intervention approaches that are embedded in existing organizational structures may improve the efficiency and effectiveness of organizational interventions, but concrete tools are lacking. In the present article, we use a realist evaluation approach to explore the role of kaizen, a lean tool for participatory continuous improvement, in improving employee well-being in two cluster-randomized, controlled participatory intervention studies. Case 1 is from the Danish Postal Service, where kaizen boards were used to implement action plans. The results of multi-group structural equation modeling showed that kaizen served as a mechanism that increased the level of awareness of and capacity to manage psychosocial issues, which, in turn, predicted increased job satisfaction and mental health. Case 2 is from a regional hospital in Sweden that integrated occupational health processes with a pre-existing kaizen system. Multi-group structural equation modeling revealed that, in the intervention group, kaizen work predicted better integration of organizational and employee objectives after 12 months, which, in turn, predicted increased job satisfaction and decreased discomfort at 24 months. The findings suggest that participatory and structured problem-solving approaches that are familiar and visual to employees can facilitate organizational interventions. PMID:28736455

ARN Integrated Retail Module (IRM) & 3D Whole Body Scanner System at Fort Carson, Colorado

DTIC Science & Technology

2006-12-01

the Central Issue Facility (CIF), Ft. Carson, CO; and, 4) Develop and validate dynamic local tariffs. Additional information on Apparel...Scanner; 3) Integrate 3D Whole Body scanning technology with the ARN Integrated Retail Module (IRM) for clothing issue at the Central Issue Facility ...CIF), Ft. Carson, CO; and, 4) Develop and validate dynamic local tariffs. The main goals of the ARN 3D scanning research initiative at the Ft

Fundamental understanding and rational design of high energy structural microbatteries

DOE PAGES

Wang, Yuxing; Li, Qiuyan; Cartmell, Samuel; ...

2017-11-21

We present that microbatteries play a critical role in determining the lifetime of downsized sensors, wearable devices, medical applications, and animal acoustic telemetry transmitters among others. More often, structural batteries are required from the perspective of aesthetics and space utilization, which is however rarely explored. Herein, we discuss the fundamental issues associated with the rational design of practically usable high energy microbatteries. The tubular shape of the cell further allows the flexible integration of microelectronics. A functioning acoustic micro-transmitter continuously powered by this tubular battery has been successfully demonstrated. Finally, multiple design features adopted to accommodate large mechanical stress duringmore » the rolling process are discussed providing new insights in designing the structural microbatteries for emerging technologies.« less

Fundamental understanding and rational design of high energy structural microbatteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Yuxing; Li, Qiuyan; Cartmell, Samuel

We present that microbatteries play a critical role in determining the lifetime of downsized sensors, wearable devices, medical applications, and animal acoustic telemetry transmitters among others. More often, structural batteries are required from the perspective of aesthetics and space utilization, which is however rarely explored. Herein, we discuss the fundamental issues associated with the rational design of practically usable high energy microbatteries. The tubular shape of the cell further allows the flexible integration of microelectronics. A functioning acoustic micro-transmitter continuously powered by this tubular battery has been successfully demonstrated. Finally, multiple design features adopted to accommodate large mechanical stress duringmore » the rolling process are discussed providing new insights in designing the structural microbatteries for emerging technologies.« less

Independent Peer Review of Communications, Navigation, and Networking re-Configurable Testbed (CoNNeCT) Project Antenna Pointing Subsystem (APS) Integrated Gimbal Assembly (IGA) Structural Analysis

NASA Technical Reports Server (NTRS)

Raju, Ivatury S.; Larsen, Curtis E.; Pellicciotti, Joseph W.

2010-01-01

Glenn Research Center Chief Engineer's Office requested an independent review of the structural analysis and modeling of the Communications, Navigation, and Networking re-Configurable Testbed (CoNNeCT) Project Antenna Pointing Subsystem (APS) Integrated Gimbal Assembly (IGA) to be conducted by the NASA Engineering and Safety Center (NESC). At this time, the IGA had completed its critical design review (CDR). The assessment was to be a peer review of the NEi-NASTRAN1 model of the APS Antenna, and not a peer review of the design and the analysis that had been completed by the GRC team for CDR. Thus, only a limited amount of information was provided on the structural analysis. However, the NESC team had difficulty separating analysis concerns from modeling issues. The team studied the NASTRAN model, but did not fully investigate how the model was used by the CoNNeCT Project and how the Project was interpreting the results. The team's findings, observations, and NESC recommendations are contained in this report.

Making psycholinguistics musical: self-paced reading time evidence for shared processing of linguistic and musical syntax.

PubMed

Slevc, L Robert; Rosenberg, Jason C; Patel, Aniruddh D

2009-04-01

Linguistic processing, especially syntactic processing, is often considered a hallmark of human cognition; thus, the domain specificity or domain generality of syntactic processing has attracted considerable debate. The present experiments address this issue by simultaneously manipulating syntactic processing demands in language and music. Participants performed self-paced reading of garden path sentences, in which structurally unexpected words cause temporary syntactic processing difficulty. A musical chord accompanied each sentence segment, with the resulting sequence forming a coherent chord progression. When structurally unexpected words were paired with harmonically unexpected chords, participants showed substantially enhanced garden path effects. No such interaction was observed when the critical words violated semantic expectancy or when the critical chords violated timbral expectancy. These results support a prediction of the shared syntactic integration resource hypothesis (Patel, 2003), which suggests that music and language draw on a common pool of limited processing resources for integrating incoming elements into syntactic structures. Notations of the stimuli from this study may be downloaded from pbr.psychonomic-journals.org/content/supplemental.

On the reading of the structural behavior of old masonry: The issue of the seismic assessment of archeological ruins

NASA Astrophysics Data System (ADS)

Fonti, Roberta

2016-12-01

This paper addresses the problem of assessing the resistance of ancient Roman structures to normal lateral forces. This subject was examined by applying theoretical models, especially for historical masonry. Procedure Guidelines for the Assessment and Reduction of Seismic Risk of Cultural Heritage [1] were followed here. A lack of information exists within the models for seismic safety assessment. They are restricted to four main categories, which do not mention structures that lack integrity (FIGURE 1, a). Archeological findings, such as masonry elements, often lack integrity and suffer from instability of isolated parties under seismic actions. Nevertheless, a realistic assessment of their safety level is crucial for their survival, especially in regions prone to earthquakes. The attainment of the necessary safety targets is difficult to achieve without reinforcement. The practice of strengthening archeological assets avoids possible collapses. Contrarily, it is responsible for irreversible changes to their historical features regardless of their historical value. However, selecting an appropriate level of building knowledge and design life can avoid the usage of extensive strengthening techniques. An illustrative example is reported in this paper.

Smart Composite Overwrapped Pressure Vessel - Integrated Structural Health Monitoring System to Meet Space Exploration and International Space Station Mission Assurance Needs

NASA Technical Reports Server (NTRS)

Saulsberry, Regor; Nichols, Charles; Waller, Jess

2012-01-01

Currently there are no integrated NDE methods for baselining and monitoring defect levels in fleet for Composite Overwrapped Pressure Vessels (COPVs) or related fracture critical composites, or for performing life-cycle maintenance inspections either in a traditional remove-and-inspect mode or in a more modern in situ inspection structural health monitoring (SHM) mode. Implicit in SHM and autonomous inspection is the existence of quantitative accept-reject criteria. To be effective, these criteria must correlate with levels of damage known to cause composite failure. Furthermore, implicit in SHM is the existence of effective remote sensing hardware and automated techniques and algorithms for interpretation of SHM data. SHM of facture critical composite structures, especially high pressure COPVs, is critical to the success of nearly every future NASA space exploration program as well as life extension of the International Space Station. It has been clearly stated that future NASA missions may not be successful without SHM [1]. Otherwise, crews will be busy addressing subsystem health issues and not focusing on the real NASA mission

What insects can tell us about the origins of consciousness

PubMed Central

Barron, Andrew B.; Klein, Colin

2016-01-01

How, why, and when consciousness evolved remain hotly debated topics. Addressing these issues requires considering the distribution of consciousness across the animal phylogenetic tree. Here we propose that at least one invertebrate clade, the insects, has a capacity for the most basic aspect of consciousness: subjective experience. In vertebrates the capacity for subjective experience is supported by integrated structures in the midbrain that create a neural simulation of the state of the mobile animal in space. This integrated and egocentric representation of the world from the animal’s perspective is sufficient for subjective experience. Structures in the insect brain perform analogous functions. Therefore, we argue the insect brain also supports a capacity for subjective experience. In both vertebrates and insects this form of behavioral control system evolved as an efficient solution to basic problems of sensory reafference and true navigation. The brain structures that support subjective experience in vertebrates and insects are very different from each other, but in both cases they are basal to each clade. Hence we propose the origins of subjective experience can be traced to the Cambrian. PMID:27091981

Reward Dependent Invigoration Relates to Theta Oscillations and Is Predicted by Dopaminergic Midbrain Integrity in Healthy Elderly.

PubMed

Steiger, Tineke K; Bunzeck, Nico

2017-01-01

Motivation can have invigorating effects on behavior via dopaminergic neuromodulation. While this relationship has mainly been established in theoretical models and studies in younger subjects, the impact of structural declines of the dopaminergic system during healthy aging remains unclear. To investigate this issue, we used electroencephalography (EEG) in healthy young and elderly humans in a reward-learning paradigm. Specifically, scene images were initially encoded by combining them with cues predicting monetary reward (high vs. low reward). Subsequently, recognition memory for the scenes was tested. As a main finding, we can show that response times (RTs) during encoding were faster for high reward predicting images in the young but not elderly participants. This pattern was resembled in power changes in the theta-band (4-7 Hz). Importantly, analyses of structural MRI data revealed that individual reward-related differences in the elderlies' response time could be predicted by the structural integrity of the dopaminergic substantia nigra (SN; as measured by magnetization transfer (MT)). These findings suggest a close relationship between reward-based invigoration, theta oscillations and age-dependent changes of the dopaminergic system.

Non-Nuclear Testing of Space Nuclear Systems at NASA MSFC

NASA Technical Reports Server (NTRS)

Houts, Michael G.; Pearson, Boise J.; Aschenbrenner, Kenneth C.; Bradley, David E.; Dickens, Ricky; Emrich, William J.; Garber, Anne; Godfroy, Thomas J.; Harper, Roger T.; Martin, Jim J.;

Interoperability-oriented Integration of Failure Knowledge into Functional Knowledge and Knowledge Transformation based on Concepts Mapping

NASA Astrophysics Data System (ADS)

Koji, Yusuke; Kitamura, Yoshinobu; Kato, Yoshikiyo; Tsutsui, Yoshio; Mizoguchi, Riichiro

In conceptual design, it is important to develop functional structures which reflect the rich experience in the knowledge from previous design failures. Especially, if a designer learns possible abnormal behaviors from a previous design failure, he or she can add an additional function which prevents such abnormal behaviors and faults. To do this, it is a crucial issue to share such knowledge about possible faulty phenomena and how to cope with them. In fact, a part of such knowledge is described in FMEA (Failure Mode and Effect Analysis) sheets, function structure models for systematic design and fault trees for FTA (Fault Tree Analysis).

Aligning USGS senior leadership structure with the USGS science strategy

USGS Publications Warehouse

,

2010-01-01

The U.S. Geological Survey (USGS) is realigning its management and budget structure to further enhance the work of its science programs and their interdisciplinary focus areas related to the USGS Science Strategy as outlined in 'Facing Tomorrow's Challenges-U.S. Geological Survey Science in the Decade 2007-2017' (U.S. Geological Survey, 2007). In 2007, the USGS developed this science strategy outlining major natural-science issues facing the Nation and focusing on areas where natural science can make a substantial contribution to the well being of the Nation and the world. These areas include global climate change, water resources, natural hazards, energy and minerals, ecosystems, and data integration.

Critical Assessment Issues in Work-Integrated Learning

ERIC Educational Resources Information Center

Ferns, Sonia; Zegwaard, Karsten E.

2014-01-01

Assessment has long been a contentious issue in work-integrated learning (WIL) and cooperative education. Despite assessment being central to the integrity and accountability of a university and long-standing theories around best practice in assessment, enacting quality assessment practices has proven to be more difficult. Authors in this special…

Introduction to the Special Issue on Neuropsychology Practices in Integrated Care Teams.

PubMed

Festa, Joanne R

2018-05-01

This special issue on neuropsychology practices in integrated healthcare teams demonstrates how neuropsychologists have transformed their practices in an evolving healthcare landscape. These contributions are an overview of the many ways in which neuropsychologists function in integrated care teams. The experiences of integrated neuropsychologists serve as a model for those seeking new practice opportunities by providing highly practical, clinically relevant information. Included in this volume are articles on education and reimbursement issues, information about clinical practices that address diagnostic issues, prognostics and clinical management, as well as surgical treatment planning and outcome prediction. Authors highlight the value of their services, their contribution to improving team and patient communication, as well as the biopsychosocial understanding of the patient. Several unexpected challenges are detailed among the pearls and pitfalls of these practices.

Ways to improve your correlation functions

NASA Technical Reports Server (NTRS)

Hamilton, A. J. S.

1993-01-01

This paper describes a number of ways to improve on the standard method for measuring the two-point correlation function of large scale structure in the Universe. Issues addressed are: (1) the problem of the mean density, and how to solve it; (2) how to estimate the uncertainty in a measured correlation function; (3) minimum variance pair weighting; (4) unbiased estimation of the selection function when magnitudes are discrete; and (5) analytic computation of angular integrals in background pair counts.

Sales compensation governance: the last frontier of corporate reform.

PubMed

Gundy, Peter R; Gaeta, Elizabeth C

2004-01-01

The area of sales compensation has remained relatively untouched by recent pressures for compensation reform. This article highlights some of the ways that sales organizations stumble in managing their compensation programs, and why it takes more than a simple tactical fix to address these problems effectively. The authors describe a more structured governance framework that not only identifies and resolves key sales compensation issues, but ultimately safeguards the effectiveness and financial integrity of the sales organization itself.

Mental health care delivery system reform in Belgium: the challenge of achieving deinstitutionalisation whilst addressing fragmentation of care at the same time.

PubMed

Nicaise, Pablo; Dubois, Vincent; Lorant, Vincent

2014-04-01

Most mental health care delivery systems in welfare states currently face two major issues: deinstitutionalisation and fragmentation of care. Belgium is in the process of reforming its mental health care delivery system with the aim of simultaneously strengthening community care and improving integration of care. The new policy model attempts to strike a balance between hospitals and community services, and is based on networks of services. We carried out a content analysis of the policy blueprint for the reform and performed an ex-ante evaluation of its plan of operation, based on the current knowledge of mental health service networks. When we examined the policy's multiple aims, intermediate goals, suggested tools, and their articulation, we found that it was unclear how the new policy could achieve its goals. Indeed, deinstitutionalisation and integration of care require different network structures, and different modes of governance. Furthermore, most of the mechanisms contained within the new policy were not sufficiently detailed. Consequently, three major threats to the effectiveness of the reform were identified. These were: issues concerning the relationship between network structure and purpose, the continued influence of hospitals despite the goal of deinstitutionalisation, and the heterogeneity in the actual implementation of the new policy. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

CALL FOR PAPERS: Special Issue on `Geometric Numerical Integration of Differential Equations'

NASA Astrophysics Data System (ADS)

Quispel, G. R. W.; McLachlan, R. I.

2005-02-01

This is a call for contributions to a special issue of Journal of Physics A: Mathematical and General entitled `Geometric Numerical Integration of Differential Equations'. This issue should be a repository for high quality original work. We are interested in having the topic interpreted broadly, that is, to include contributions dealing with symplectic or multisymplectic integration; volume-preserving integration; symmetry-preserving integration; integrators that preserve first integrals, Lyapunov functions, or dissipation; exponential integrators; integrators for highly oscillatory systems; Lie-group integrators, etc. Papers on geometric integration of both ODEs and PDEs will be considered, as well as application to molecular-scale integration, celestial mechanics, particle accelerators, fluid flows, population models, epidemiological models and/or any other areas of science. We believe that this issue is timely, and hope that it will stimulate further development of this new and exciting field. The Editorial Board has invited G R W Quispel and R I McLachlan to serve as Guest Editors for the special issue. Their criteria for acceptance of contributions are the following: • The subject of the paper should relate to geometric numerical integration in the sense described above. • Contributions will be refereed and processed according to the usual procedure of the journal. • Papers should be original; reviews of a work published elsewhere will not be accepted. The guidelines for the preparation of contributions are as follows: • The DEADLINE for submission of contributions is 1 September 2005. This deadline will allow the special issue to appear in late 2005 or early 2006. • There is a strict page limit of 16 printed pages (approximately 9600 words) per contribution. For papers exceeding this limit, the Guest Editors reserve the right to request a reduction in length. Further advice on publishing your work in Journal of Physics A: Mathematical and General may be found at www.iop.org/Journals/jphysa. • Contributions to the special issue should if possible be submitted electronically by web upload at {www.iop.org/Journals/jphysa or by e-mail to jphysa@iop.org, quoting `JPhysA Special Issue—Geometric Integration'. Submissions should ideally be in standard LaTeX form; we are, however, able to accept most formats including Microsoft Word. Please see the web site for further information on electronic submissions. • Authors unable to submit electronically may send hard copy contributions to: Publishing Administrators, Journal of Physics A, Institute of Physics Publishing, Dirac House, Temple Back, Bristol BS1 6BE, UK, enclosing the electronic code on floppy disk if available and quoting `JPhysA Special Issue—Geometric Integration'. • All contributions should be accompanied by a read-me file or covering letter giving the postal and e-mail addresses for correspondence. The Publishing Office should be notified of any subsequent change of address. This special issue will be published in the paper and online version of the journal. The corresponding author of each contribution will receive a complimentary copy of the issue. G R W Quispel and R I McLachlan Guest Editors

Methods and Issues for the Combined Use of Integral Experiments and Covariance Data: Results of a NEA International Collaborative Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Palmiotti, Giuseppe; Salvatores, Massimo

2014-04-01

The Working Party on International Nuclear Data Evaluation Cooperation (WPEC) of the Nuclear Science Committee under the Nuclear Energy Agency (NEA/OECD) established a Subgroup (called “Subgroup 33”) in 2009 on “Methods and issues for the combined use of integral experiments and covariance data.” The first stage was devoted to producing the description of different adjustment methodologies and assessing their merits. A detailed document related to this first stage has been issued. Nine leading organizations (often with a long and recognized expertise in the field) have contributed: ANL, CEA, INL, IPPE, JAEA, JSI, NRG, IRSN and ORNL. In the second stagemore » a practical benchmark exercise was defined in order to test the reliability of the nuclear data adjustment methodology. A comparison of the results obtained by the participants and major lessons learned in the exercise are discussed in the present paper that summarizes individual contributions which often include several original developments not reported separately. The paper provides the analysis of the most important results of the adjustment of the main nuclear data of 11 major isotopes in a 33-group energy structure. This benchmark exercise was based on a set of 20 well defined integral parameters from 7 fast assembly experiments. The exercise showed that using a common shared set of integral experiments but different starting evaluated libraries and/or different covariance matrices, there is a good convergence of trends for adjustments. Moreover, a significant reduction of the original uncertainties is often observed. Using the a–posteriori covariance data, there is a strong reduction of the uncertainties of integral parameters for reference reactor designs, mainly due to the new correlations in the a–posteriori covariance matrix. Furthermore, criteria have been proposed and applied to verify the consistency of differential and integral data used in the adjustment. Finally, recommendations are given for an appropriate use of sensitivity analysis methods and indications for future work are provided.« less

The role of nurse specialists in the delivery of integrated diabetes care: a cross-sectional survey of diabetes nurse specialist services

PubMed Central

Riordan, Fiona; McHugh, Sheena M; Murphy, Katie; Barrett, Julie; Kearney, Patricia M

2017-01-01

Objectives International evidence suggests the diabetes nurse specialist (DNS) has a key role in supporting integrated management of diabetes. We examine whether hospital and community DNS currently support the integration of care, examine regional variation in aspects of the service relevant to the delivery of integrated care and identify barriers to service delivery and areas for improvement. Design A cross-sectional survey of hospital and community-based DNS in Ireland. Methods Between September 2015 and April 2016, a 67-item online survey, comprising closed and open questions on their clinical role, diabetes clinics, multidisciplinary working, and barriers and facilitators to service delivery, was administered to all eligible DNS (n=152) in Ireland. DNS were excluded if they were retired or on maternity leave or extended leave. Results The response rate was 66.4% (n=101): 60.6% (n=74) and 89.3% (n=25) among hospital and community DNS, respectively. Most DNS had patients with stable (81.8%) and complicated type 2 diabetes mellitus (89.9%) attending their service. The majority were delivering nurse-led clinics (81.1%). Almost all DNS had a role liaising with (91%), and providing support and education to (95%), other professionals. However, only a third reported that there was local agreement on how their service should operate between the hospital and primary care. Barriers to service delivery that were experienced by DNS included deficits in the availability of specialist staff (allied health professionals, endocrinologists and DNS), insufficient space for clinics, structured education and issues with integration. Conclusions Delivering integrated diabetes care through a nurse specialist-led approach requires that wider service issues, including regional disparities in access to specialist resources and formalising agreements and protocols on multidisciplinary working between settings, be explicitly addressed. PMID:28801394

Intra-plastid protein trafficking: how plant cells adapted prokaryotic mechanisms to the eukaryotic condition.

PubMed

Celedon, Jose M; Cline, Kenneth

2013-02-01

Protein trafficking and localization in plastids involve a complex interplay between ancient (prokaryotic) and novel (eukaryotic) translocases and targeting machineries. During evolution, ancient systems acquired new functions and novel translocation machineries were developed to facilitate the correct localization of nuclear encoded proteins targeted to the chloroplast. Because of its post-translational nature, targeting and integration of membrane proteins posed the biggest challenge to the organelle to avoid aggregation in the aqueous compartments. Soluble proteins faced a different kind of problem since some had to be transported across three membranes to reach their destination. Early studies suggested that chloroplasts addressed these issues by adapting ancient-prokaryotic machineries and integrating them with novel-eukaryotic systems, a process called 'conservative sorting'. In the last decade, detailed biochemical, genetic, and structural studies have unraveled the mechanisms of protein targeting and localization in chloroplasts, suggesting a highly integrated scheme where ancient and novel systems collaborate at different stages of the process. In this review we focus on the differences and similarities between chloroplast ancestral translocases and their prokaryotic relatives to highlight known modifications that adapted them to the eukaryotic situation. This article is part of a Special Issue entitled: Protein Import and Quality Control in Mitochondria and Plastids. Copyright © 2012 Elsevier B.V. All rights reserved.

Park system concept for environmental sustainabilityin urban spatial development

NASA Astrophysics Data System (ADS)

Uniaty, Q.

2018-01-01

Urban Park System is an integrated concept between nature system and urban life. The problems caused by urban population activity resulted in the need to increase the balance between two systems. Establishment of urban park system is a response to the need for resilience of urban space structures. As an ideal requirement it needs to be built integration between the ecological, social, economic, aesthetic aspects of urban landscape architecture. The methodology was developed based on an approach to issues affecting the conditions due to urban issues and its relation to the development efforts of urban park system; Observation of Jakarta problem was obtained based on published studies and data, literature, characteristic and potential analyzes, local physical, from limited field observations. Both are simple methods aimed to describe the nature of a condition as well as form characteristics of problems in controlling the development of region, to examine the causes and symptoms. This method try to assess an object study compared between the conditions before and after. The benefits of urban park system development will not only improve the urban environment, but the value of urban pride, identity and control urban growth in line with efforts to improve the balance between conservation and development. Integrated urban park system will enhance the multifunctional role, connectivity, habitability, durability, identity and investment.

Opto-microwave, Butler matrixes based front-end for a multi-beam large direct radiating array antenna

NASA Astrophysics Data System (ADS)

Piqueras, M. A.; Mengual, T.; Navasquillo, O.; Sotom, M.; Caille, G.

2017-11-01

The evolution of broadband communication satellites shows a clear trend towards beam forming and beamswitching systems with efficient multiple access schemes with wide bandwidths, for which to be economically viable, the communication price shall be as low as possible. In such applications, the most demanding antenna concept is the Direct Radiating Array (DRA) since its use allows a flexible power allocation between beams and may afford failures in their active chains with low impact on the antenna radiating pattern. Forming multiple antenna beams, as for `multimedia via satellite' missions, can be done mainly in three ways: in microwave domain, by digital or optical processors: - Microwave beam-formers are strongly constrained by the mass and volume of microwave devices and waveguides - the bandwidth of digital processors is limited due to power consumption and complexity constraints. - The microwave photonics is an enabling technology that can improve the antenna feeding network performances, overcoming the limitations of the traditional technology in the more demanding scenarios, and may overcome the conventional RF beam-former issues, to generate accurately the very numerous time delays or phase shifts required in a DRA with a large number of beams and of radiating elements. Integrated optics technology can play a crucial role as an alternative technology for implementing beam-forming structures for satellite applications thanks to the well known advantages of this technology such as low volume and weight, huge electrical bandwidth, electro-magnetic interference immunity, low consumption, remote delivery capability with low-attenuation (by carrying all microwave signals over optical fibres) and the robustness and precision that exhibits integrated optics. Under the ESA contract 4000105095/12/NL/RA the consortium formed by DAS Photonics, Thales Alenia Space and the Nanophotonic Technology Center of Valencia is developing a three-dimensional Optical Beamforming Network (OBFN) based on integrated photonics, with fibre-optics remote antenna feeding capabilities, that addresses the requirements of SoA DRA antennas in space communications, able to feed potentially hundreds of antenna elements with hundred of simultaneous, orthogonal beams. The core of this OBFN is a Photonic Integrated Circuit (PIC) implementing a passive Butler matrix similar to the structure well known by the RF community, but overcoming the issues of scalability, size, compactness and manufacturability associated to the fact of addressing hundred of elements. This fully-integrated beam-former solution also overcomes the opto-mechanical issues and environmental sensitivity of other free-space based OBFNs.

Development and validation of the crew-station system-integration research facility

NASA Technical Reports Server (NTRS)

Nedell, B.; Hardy, G.; Lichtenstein, T.; Leong, G.; Thompson, D.

1986-01-01

The various issues associated with the use of integrated flight management systems in aircraft were discussed. To address these issues a fixed base integrated flight research (IFR) simulation of a helicopter was developed to support experiments that contribute to the understanding of design criteria for rotorcraft cockpits incorporating advanced integrated flight management systems. A validation experiment was conducted that demonstrates the main features of the facility and the capability to conduct crew/system integration research.

Introduction to the Issue on Segregation, Desegregation, and Integration: From History, to Policy, to Practice

ERIC Educational Resources Information Center

Diem, Sarah; Brooks, Jeffrey

2013-01-01

The articles in this special issue examine the increasingly complex relationship between segregation, desegregation, and integration in a sociopolitical environment vastly different from that of the initial days of desegregation. These issues are examined from historical and political perspectives, contextualizing the complexities of segregation,…

A governance model for integrated primary/secondary care for the health-reforming first world – results of a systematic review

PubMed Central

2013-01-01

Background Internationally, key health care reform elements rely on improved integration of care between the primary and secondary sectors. The objective of this systematic review is to synthesise the existing published literature on elements of current integrated primary/secondary health care. These elements and how they have supported integrated healthcare governance are presented. Methods A systematic review of peer-reviewed literature from PubMed, MEDLINE, CINAHL, the Cochrane Library, Informit Health Collection, the Primary Health Care Research and Information Service, the Canadian Health Services Research Foundation, European Foundation for Primary Care, European Forum for Primary Care, and Europa Sinapse was undertaken for the years 2006–2012. Relevant websites were also searched for grey literature. Papers were assessed by two assessors according to agreed inclusion criteria which were published in English, between 2006–2012, studies describing an integrated primary/secondary care model, and had reported outcomes in care quality, efficiency and/or satisfaction. Results Twenty-one studies met the inclusion criteria. All studies evaluated the process of integrated governance and service delivery structures, rather than the effectiveness of services. They included case reports and qualitative data analyses addressing policy change, business issues and issues of clinical integration. A thematic synthesis approach organising data according to themes identified ten elements needed for integrated primary/secondary health care governance across a regional setting including: joint planning; integrated information communication technology; change management; shared clinical priorities; incentives; population focus; measurement – using data as a quality improvement tool; continuing professional development supporting joint working; patient/community engagement; and, innovation. Conclusions All examples of successful primary/secondary care integration reported in the literature have focused on a combination of some, if not all, of the ten elements described in this paper, and there appears to be agreement that multiple elements are required to ensure successful and sustained integration efforts. Whilst no one model fits all systems these elements provide a focus for setting up integration initiatives which need to be flexible for adapting to local conditions and settings. PMID:24359610

A governance model for integrated primary/secondary care for the health-reforming first world - results of a systematic review.

PubMed

Nicholson, Caroline; Jackson, Claire; Marley, John

2013-12-20

Internationally, key health care reform elements rely on improved integration of care between the primary and secondary sectors. The objective of this systematic review is to synthesise the existing published literature on elements of current integrated primary/secondary health care. These elements and how they have supported integrated healthcare governance are presented. A systematic review of peer-reviewed literature from PubMed, MEDLINE, CINAHL, the Cochrane Library, Informit Health Collection, the Primary Health Care Research and Information Service, the Canadian Health Services Research Foundation, European Foundation for Primary Care, European Forum for Primary Care, and Europa Sinapse was undertaken for the years 2006-2012. Relevant websites were also searched for grey literature. Papers were assessed by two assessors according to agreed inclusion criteria which were published in English, between 2006-2012, studies describing an integrated primary/secondary care model, and had reported outcomes in care quality, efficiency and/or satisfaction. Twenty-one studies met the inclusion criteria. All studies evaluated the process of integrated governance and service delivery structures, rather than the effectiveness of services. They included case reports and qualitative data analyses addressing policy change, business issues and issues of clinical integration. A thematic synthesis approach organising data according to themes identified ten elements needed for integrated primary/secondary health care governance across a regional setting including: joint planning; integrated information communication technology; change management; shared clinical priorities; incentives; population focus; measurement - using data as a quality improvement tool; continuing professional development supporting joint working; patient/community engagement; and, innovation. All examples of successful primary/secondary care integration reported in the literature have focused on a combination of some, if not all, of the ten elements described in this paper, and there appears to be agreement that multiple elements are required to ensure successful and sustained integration efforts. Whilst no one model fits all systems these elements provide a focus for setting up integration initiatives which need to be flexible for adapting to local conditions and settings.

Innovation and Integrity in Intervention Research: Conceptual Issues, Methodology, and Knowledge Translation.

PubMed

Malti, Tina; Beelmann, Andreas; Noam, Gil G; Sommer, Simon

2018-04-01

In this article, we introduce the special issue entitled Innovation and Integrity in Intervention Science. Its focus is on essential problems and prospects for intervention research examining two related topics, i.e., methodological issues and research integrity, and challenges in the transfer of research knowledge into practice and policy. The main aims are to identify how to advance methodology in order to improve research quality, examine scientific integrity in the field of intervention science, and discuss future steps to enhance the transfer of knowledge about evidence-based intervention principles into sustained practice, routine activities, and policy decisions. Themes of the special issue are twofold. The first includes questions about research methodology in intervention science, both in terms of research design and methods, as well as data analyses and the reporting of findings. Second, the issue tackles questions surrounding the types of knowledge translation frameworks that might be beneficial to mobilize the transfer of research-based knowledge into practice and public policies. The issue argues that innovations in methodology and thoughtful approaches to knowledge translation can enable transparency, quality, and sustainability of intervention research.

Methodological Problems on the Way to Integrative Human Neuroscience.

PubMed

Kotchoubey, Boris; Tretter, Felix; Braun, Hans A; Buchheim, Thomas; Draguhn, Andreas; Fuchs, Thomas; Hasler, Felix; Hastedt, Heiner; Hinterberger, Thilo; Northoff, Georg; Rentschler, Ingo; Schleim, Stephan; Sellmaier, Stephan; Tebartz Van Elst, Ludger; Tschacher, Wolfgang

2016-01-01

Neuroscience is a multidisciplinary effort to understand the structures and functions of the brain and brain-mind relations. This effort results in an increasing amount of data, generated by sophisticated technologies. However, these data enhance our descriptive knowledge , rather than improve our understanding of brain functions. This is caused by methodological gaps both within and between subdisciplines constituting neuroscience, and the atomistic approach that limits the study of macro- and mesoscopic issues. Whole-brain measurement technologies do not resolve these issues, but rather aggravate them by the complexity problem. The present article is devoted to methodological and epistemic problems that obstruct the development of human neuroscience. We neither discuss ontological questions (e.g., the nature of the mind) nor review data, except when it is necessary to demonstrate a methodological issue. As regards intradisciplinary methodological problems, we concentrate on those within neurobiology (e.g., the gap between electrical and chemical approaches to neurophysiological processes) and psychology (missing theoretical concepts). As regards interdisciplinary problems, we suggest that core disciplines of neuroscience can be integrated using systemic concepts that also entail human-environment relations. We emphasize the necessity of a meta-discussion that should entail a closer cooperation with philosophy as a discipline of systematic reflection. The atomistic reduction should be complemented by the explicit consideration of the embodiedness of the brain and the embeddedness of humans. The discussion is aimed at the development of an explicit methodology of integrative human neuroscience , which will not only link different fields and levels, but also help in understanding clinical phenomena.

Methodological Problems on the Way to Integrative Human Neuroscience

PubMed Central

Kotchoubey, Boris; Tretter, Felix; Braun, Hans A.; Buchheim, Thomas; Draguhn, Andreas; Fuchs, Thomas; Hasler, Felix; Hastedt, Heiner; Hinterberger, Thilo; Northoff, Georg; Rentschler, Ingo; Schleim, Stephan; Sellmaier, Stephan; Tebartz Van Elst, Ludger; Tschacher, Wolfgang

2016-01-01

Neuroscience is a multidisciplinary effort to understand the structures and functions of the brain and brain-mind relations. This effort results in an increasing amount of data, generated by sophisticated technologies. However, these data enhance our descriptive knowledge, rather than improve our understanding of brain functions. This is caused by methodological gaps both within and between subdisciplines constituting neuroscience, and the atomistic approach that limits the study of macro- and mesoscopic issues. Whole-brain measurement technologies do not resolve these issues, but rather aggravate them by the complexity problem. The present article is devoted to methodological and epistemic problems that obstruct the development of human neuroscience. We neither discuss ontological questions (e.g., the nature of the mind) nor review data, except when it is necessary to demonstrate a methodological issue. As regards intradisciplinary methodological problems, we concentrate on those within neurobiology (e.g., the gap between electrical and chemical approaches to neurophysiological processes) and psychology (missing theoretical concepts). As regards interdisciplinary problems, we suggest that core disciplines of neuroscience can be integrated using systemic concepts that also entail human-environment relations. We emphasize the necessity of a meta-discussion that should entail a closer cooperation with philosophy as a discipline of systematic reflection. The atomistic reduction should be complemented by the explicit consideration of the embodiedness of the brain and the embeddedness of humans. The discussion is aimed at the development of an explicit methodology of integrative human neuroscience, which will not only link different fields and levels, but also help in understanding clinical phenomena. PMID:27965548

A web-enabled system for integrated assessment of watershed development

USGS Publications Warehouse

Dymond, R.; Lohani, V.; Regmi, B.; Dietz, R.

2004-01-01

Researchers at Virginia Tech have put together the primary structure of a web enabled integrated modeling system that has potential to be a planning tool to help decision makers and stakeholders in making appropriate watershed management decisions. This paper describes the integrated system, including data sources, collection, analysis methods, system software and design, and issues of integrating the various component models. The integrated system has three modeling components, namely hydrology, economics, and fish health, and is accompanied by descriptive 'help files.' Since all three components have a related spatial aspect, GIS technology provides the integration platform. When completed, a user will access the integrated system over the web to choose pre-selected land development patterns to create a 'what if' scenario using an easy-to-follow interface. The hydrologic model simulates effects of the scenario on annual runoff volume, flood peaks of various return periods, and ground water recharge. The economics model evaluates tax revenue and fiscal costs as a result of a new land development scenario. The fish health model evaluates effects of new land uses in zones of influence to the health of fish populations in those areas. Copyright ASCE 2004.

Moral competence as a positive youth development construct: conceptual bases and implications for curriculum development.

PubMed

Ma, Hing Keung

2006-01-01

Moral competence refers to the orientation to perform altruistic behavior and the ability to judge moral issues logically, consistently and at an advanced level of development. A brief review of the concepts of altruism and justice is presented. The gender and cultural issues are also discussed. The contents of moral competence program units include four major topics: (1) Fairness, (2) Proper conduct (mainly altruistic and prosocial orientation), (3) Responsibility and altruistic orientation, and (4) Integrity and fairness. The general goal is to help students to develop an altruistic orientation and a judgment structure of a high level of justice. This paper is part of the development of the positive youth development program in Hong Kong.

The Detroit River, Michigan: an ecological profile

USGS Publications Warehouse

Manny, Bruce A.; Edsall, Thomas A.; Jaworski, Eugene

1988-01-01

A part of the connecting channel system between Lake Huron and Lake Erie, the Detroit River forms an integral link between the two lakes for both humans and biological resources such as fish, nutrients, and plant detritus. This profile summarizes existing scientific information on the ecological structure and functioning of this ecosystem. Topics include the geological history of the region, climatic influences, river hydrology, lower trophic-level biotic components, native and introduced fishes, waterfowl use, ecological interrelationships, commercial and recreational uses of the river, and current management issues. Despite urbanization, the river still supports diverse fish, waterfowl, and benthic populations. Management issues include sewer overflows; maintenance dredging for navigation and port activities; industrial discharges of potentially hazardous materials; and wetland, fishery, and waterfowl protection and enhancement.

Methods for the scientific study of discrimination and health: an ecosocial approach.

PubMed

Krieger, Nancy

2012-05-01

The scientific study of how discrimination harms health requires theoretically grounded methods. At issue is how discrimination, as one form of societal injustice, becomes embodied inequality and is manifested as health inequities. As clarified by ecosocial theory, methods must address the lived realities of discrimination as an exploitative and oppressive societal phenomenon operating at multiple levels and involving myriad pathways across both the life course and historical generations. An integrated embodied research approach hence must consider (1) the structural level-past and present de jure and de facto discrimination; (2) the individual level-issues of domains, nativity, and use of both explicit and implicit discrimination measures; and (3) how current research methods likely underestimate the impact of racism on health.

Hanford Double-Shell Tank Inspection Annual Report Calendar Year 2012

DOE Office of Scientific and Technical Information (OSTI.GOV)

Petermann, Tasha M.; Boomer, Kayle D.; Washenfelder, D. J.

2013-12-02

The double-shell tanks (DSTs) were constructed between 1968 and 1986. They will have exceeded their design life before the waste can be removed and trasferred to the Waste Treatment and Immobilization Plant for vitrification. The Double-Shell Tank Integrity Project has been established to evaluate tank aging, and ensure that each tank is structurally sound for continued use. This is the first issue of the Double-Shell Tank Inspection Annual Report. The purpose of this issue is to summarize the results of DST inspections conducted from the beginnng of the inspection program through the end of CY2012. Hereafter, the report will bemore » updated annually with summaries of the past year's DST inspection activities.« less

Labour migration and the single European market: a synthetic and prospective note.

PubMed

Ardittis, S

1990-12-01

"The present paper is an attempt to analyse and forecast the following major issues relating to migration in Europe after 1992: (i) the evolution and structure of intra-European flows in the forthcoming single European market; (ii) the integration, after 1992, of established immigrant communities, including ethnic minorities and second generation groups; (iii) future immigration from non-EC member states.... The article explains that, in addition to policy-related mutations inherent in the completion of the internal market, other factors (demographic changes and insufficient enrolment of national graduate students in key disciplines) and issues (emergence of atypical groups such as second generation and Eastern European migrants), are due to generate new patterns and modified interests in European labour migration after 1992." excerpt

Performance of fuselage pressure structure

NASA Technical Reports Server (NTRS)

Maclin, James R.

1992-01-01

There are currently more than 1,000 Boeing airplanes around the world over 20 years old. That number is expected to double by the year 1995. With these statistics comes the reality that structural airworthiness will be in the forefront of aviation issues well into the next century. The results of previous and recent test programs Boeing has implemented to study the structural performance of older airplanes relative to pressurized fuselage sections are described. Included in testing were flat panels with multiple site damage (MSD), a full-scale 737 and 2 747s as well as panels representing a 737 and 777, and a generic aircraft in large pressure-test fixtures. Because damage is a normal part of aging, focus is on the degree to which structural integrity is maintained after failure or partial failure of any structural element, including multiple site damage (MSD), and multiple element damage (MED).

An Integral Psychology Response to Helminiak's (2001) "Treating Spiritual Issues in Secular Psychotherapy."

ERIC Educational Resources Information Center

Marquis, Andre; Holden, Janice Miner; Warren, E. Scott

2001-01-01

Presents a response to D. A. Helminiak's (2001) article from the perspective of K. Wilber's integral psychology. Discusses a summary of integral psychology; various conceptual issues; and usefulness to mental health practitioners (MHPs). Argues that K. Wilber's model is more comprehensive, clear, coherent, and helpful to MHPs than Helminiak's…

75 FR 39472 - Airworthiness Directives; Eclipse Aerospace, Inc. Model EA500 Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-09

..., altitude preselect, and/or transponder codes. We are proposing this AD to correct faulty integration of... determined to be a software communication integration issue between the EFIS display interface and associated... transponder codes. We are issuing this AD to correct faulty integration of hardware and software, which could...

Just Another Format: Integrating Resources for Users of Personal Digital Assistants

ERIC Educational Resources Information Center

Koufogiannakis, Denise; Ryan, Pam; Dahl, Susan

2005-01-01

This article discusses the integration of library resources for users of personal digital assistants (PDAs), with a focus on collections issues within an academic environment. The University of Alberta Libraries' PDA services initiative is used as an example of integrating services and resources into a library collection. Licensing issues, loaning…

Application of a design-build-team approach to low cost and weight composite fuselage structure

NASA Technical Reports Server (NTRS)

Ilcewicz, L. B.; Walker, T. H.; Willden, K. S.; Swanson, G. D.; Truslove, G.; Metschan, S. L.; Pfahl, C. L.

1991-01-01

Relationships between manufacturing costs and design details must be understood to promote the application of advanced composite technologies to transport fuselage structures. A team approach, integrating the disciplines responsible for aircraft structural design and manufacturing, was developed to perform cost and weight trade studies for a twenty-foot diameter aft fuselage section. Baseline composite design and manufacturing concepts were selected for large quadrant panels in crown, side, and keel areas of the fuselage section. The associated technical issues were also identified. Detailed evaluation of crown panels indicated the potential for large weight savings and costs competitive with aluminum technology in the 1995 timeframe. Different processes and material forms were selected for the various elements that comprise the fuselage structure. Additional cost and weight savings potential was estimated for future advancements.

Toward “optimal” integration of terrestrial biosphere models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schwalm, Christopher R.; Huntingzger, Deborah; Fisher, Joshua B.

2015-06-10

Multi-model ensembles (MME) are commonplace in Earth system modeling. Here we perform MME integration using a 10-member ensemble of terrestrial biosphere models (TBMs) from the Multi-scale synthesis and Terrestrial Model Intercomparison Project (MsTMIP). We contrast optimal (skill-based for present-day carbon cycling) versus naïve (“one model – one vote”) integration. MsTMIP optimal and naïve mean land sink strength estimates (–1.16 vs. –1.15 Pg C per annum respectively) are statistically indistinguishable. This holds also for grid cell values and extends to gross uptake, biomass, and net ecosystem productivity. TBM skill is similarly indistinguishable. The added complexity of skill-based integration does not materiallymore » change MME values. This suggests that carbon metabolism has predictability limits and/or that all models and references are misspecified. Resolving this issue requires addressing specific uncertainty types (initial conditions, structure, references) and a change in model development paradigms currently dominant in the TBM community.« less

Highly integrated autonomous lab-on-a-chip device for on-line and in situ determination of environmental chemical parameters.

PubMed

Martinez-Cisneros, Cynthia; da Rocha, Zaira; Seabra, Antonio; Valdés, Francisco; Alonso-Chamarro, Julián

2018-06-05

The successful integration of sample pretreatment stages, sensors, actuators and electronics in microfluidic devices enables the attainment of complete micro total analysis systems, also known as lab-on-a-chip devices. In this work, we present a novel monolithic autonomous microanalyzer that integrates microfluidics, electronics, a highly sensitive photometric detection system and a sample pretreatment stage consisting on an embedded microcolumn, all in the same device, for on-line determination of relevant environmental parameters. The microcolumn can be filled/emptied with any resin or powder substrate whenever required, paving the way for its application to several analytical processes: separation, pre-concentration or ionic-exchange. To promote its autonomous operation, avoiding issues caused by bubbles in photometric detection systems, an efficient monolithic bubble removal structure was also integrated. To demonstrate its feasibility, the microanalyzer was successfully used to determine nitrate and nitrite in continuous flow conditions, providing real time and continuous information.

TOWARD INTEGRATION IN THE CONTEXT OF HEALTH TECHNOLOGY ASSESSMENT: THE NEED FOR EVALUATIVE FRAMEWORKS.

PubMed

van der Wilt, Gert Jan; Gerhardus, Ansgar; Oortwijn, Wija

2017-01-01

A comprehensive health technology assessment (HTA) enables a patient-centered assessment of the effectiveness, economic, ethical, socio-cultural, and legal issues of health technologies that takes context and implementation into account. A question is whether these various pieces of evidence need to be integrated, and if so, how that might be achieved. The objective of our study is to discuss the meaning of integration in the context of HTA and suggest how it may be achieved in a more structured way. An analysis of the concept of integration in the context of HTA and a review of approaches that were adopted in the INTEGRATE-HTA project that may support integration. Current approaches to integration in HTA are mainly methods of commensuration, which are not optimally geared to support public deliberation. In contrast, articulating evaluative frameworks could be an important means of integration which allows for exploring how facts and values can be brought to bear on each other. Integration is not something that only needs to be addressed at the end, but rather throughout an HTA, right from the start. Integration can be conceived as a matter of accounting for the relevance of empirical evidence in view of a commitment to a set of potentially conflicting values. Various elements of the INTEGRATE-HTA project, such as scoping and the development of logic models, can help to achieve integration in HTA.

Digitalization Culture VS Archaeological Visualization: Integration of Pipelines and Open Issues

NASA Astrophysics Data System (ADS)

Cipriani, L.; Fantini, F.

2017-02-01

Scholars with different backgrounds have carried out extensive surveys centred on how 3D digital models, data acquisition and processing have changed over the years in fields of archaeology and architecture and more in general in the Cultural Heritage panorama: the current framework focused on reality-based modelling is then split in several branches: acquisition, communication and analysis of buildings (Pintus et alii, 2014). Despite the wide set of well-structured and all-encompassing surveys on the IT application in Cultural Heritage, several open issues still seem to be present, in particular once the purpose of digital simulacra is the one to fit with the "pre-informatics" legacy of architectural/archaeological representation (historical drawings with their graphic codes and aesthetics). Starting from a series of heterogeneous matters that came up studying two Italian UNESCO sites, this paper aims at underlining the importance of integrating different pipelines from different technological fields, in order to achieve multipurpose models, capable to comply with graphic codes of traditional survey, as well as semantic enrichment, and last but not least, data compression/portability and texture reliability under different lighting simulation.

Suicide Risk Assessment Training for Psychology Doctoral Programs: Core Competencies and a Framework for Training

PubMed Central

Cramer, Robert J.; Johnson, Shara M.; McLaughlin, Jennifer; Rausch, Emilie M.; Conroy, Mary Alice

2014-01-01

Clinical and counseling psychology programs currently lack adequate evidence-based competency goals and training in suicide risk assessment. To begin to address this problem, this article proposes core competencies and an integrated training framework that can form the basis for training and research in this area. First, we evaluate the extent to which current training is effective in preparing trainees for suicide risk assessment. Within this discussion, sample and methodological issues are reviewed. Second, as an extension of these methodological training issues, we integrate empirically- and expert-derived suicide risk assessment competencies from several sources with the goal of streamlining core competencies for training purposes. Finally, a framework for suicide risk assessment training is outlined. The approach employs Objective Structured Clinical Examination (OSCE) methodology, an approach commonly utilized in medical competency training. The training modality also proposes the Suicide Competency Assessment Form (SCAF), a training tool evaluating self- and observer-ratings of trainee core competencies. The training framework and SCAF are ripe for empirical evaluation and potential training implementation. PMID:24672588

Suicide Risk Assessment Training for Psychology Doctoral Programs: Core Competencies and a Framework for Training.

PubMed

Cramer, Robert J; Johnson, Shara M; McLaughlin, Jennifer; Rausch, Emilie M; Conroy, Mary Alice

2013-02-01

Clinical and counseling psychology programs currently lack adequate evidence-based competency goals and training in suicide risk assessment. To begin to address this problem, this article proposes core competencies and an integrated training framework that can form the basis for training and research in this area. First, we evaluate the extent to which current training is effective in preparing trainees for suicide risk assessment. Within this discussion, sample and methodological issues are reviewed. Second, as an extension of these methodological training issues, we integrate empirically- and expert-derived suicide risk assessment competencies from several sources with the goal of streamlining core competencies for training purposes. Finally, a framework for suicide risk assessment training is outlined. The approach employs Objective Structured Clinical Examination (OSCE) methodology, an approach commonly utilized in medical competency training. The training modality also proposes the Suicide Competency Assessment Form (SCAF), a training tool evaluating self- and observer-ratings of trainee core competencies. The training framework and SCAF are ripe for empirical evaluation and potential training implementation.

NREL Leads Energy Systems Integration, Continuum Magazine: Issue 4 (Book)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2013-04-01

Continuum Magazine showcases NREL's latest and most impactful clean energy innovations. This issue, 'NREL Leads Energy Systems Integration' explores the discipline of energy systems integration, in particular the role of the laboratory's new, one-of-a-kind Energy System Integration Facility. NREL scientists, engineers, and analysts deeply understand the fundamental science and technologies underpinning major energy producing and consuming systems, as well as the transmission infrastructure and communications and data networks required to integrate energy systems at all scales.

Human Systems Integration and Automation Issues in Small Unmanned Aerial Vehicles

NASA Technical Reports Server (NTRS)

McCauley, Michael E.; Matsangas, Panagiotis

2004-01-01

The goal of this report is to identify Human System Integration (HSI) and automation issues that contribute to improved effectiveness and efficiency in the operation of U.S. military Small Unmanned Aerial Vehicles (SUAVs). HSI issues relevant to SUAV operations are reviewed and observations from field trials are summarized. Short-term improvements are suggested research issues are identified and an overview is provided of automation technologies applicable to future SUAV design.

Towards AN Integration of GIS and Bim Data: what are the Geometric and Topological Issues?

NASA Astrophysics Data System (ADS)

Arroyo Ohori, K.; Biljecki, F.; Diakité, A.; Krijnen, T.; Ledoux, H.; Stoter, J.

2017-10-01

Geographic information and building information modelling both model buildings and infrastructure, but the way in which they are modelled is usually complimentary and BIM-GIS integration is widely considered as a way forward for both domains. For one, more detailed BIM data can feed more general GIS data and GIS data can provide the context that is necessary to BIM data. While previous studies have focused on the theoretical aspects of such an integration at a schema level, in this paper we focus on explaining the geometric and topological issues we have found while trying to develop software to realise such an integration in practice and at a data level. In our preliminary results, which are presented here, we have found that many issues for such an integration remain: handling the geometric and topological problems in BIM models, dealing with bad georeferencing and figuring out the best way to convert data between IFC and CityGML are all open issues.

Building an Ontology for Identity Resolution in Healthcare and Public Health

PubMed Central

Duncan, Jeffrey; Eilbeck, Karen; Narus, Scott P.; Clyde, Stephen; Thornton, Sidney; Staes, Catherine

2015-01-01

Integration of disparate information from electronic health records, clinical data warehouses, birth certificate registries and other public health information systems offers great potential for clinical care, public health practice, and research. Such integration, however, depends on correctly matching patient-specific records using demographic identifiers. Without standards for these identifiers, record linkage is complicated by issues of structural and semantic heterogeneity. Objectives: Our objectives were to develop and validate an ontology to: 1) identify components of identity and events subsequent to birth that result in creation, change, or sharing of identity information; 2) develop an ontology to facilitate data integration from multiple healthcare and public health sources; and 3) validate the ontology’s ability to model identity-changing events over time. Methods: We interviewed domain experts in area hospitals and public health programs and developed process models describing the creation and transmission of identity information among various organizations for activities subsequent to a birth event. We searched for existing relevant ontologies. We validated the content of our ontology with simulated identity information conforming to scenarios identified in our process models. Results: We chose the Simple Event Model (SEM) to describe events in early childhood and integrated the Clinical Element Model (CEM) for demographic information. We demonstrated the ability of the combined SEM-CEM ontology to model identity events over time. Conclusion: The use of an ontology can overcome issues of semantic and syntactic heterogeneity to facilitate record linkage. PMID:26392849

Designing and benchmarking the MULTICOM protein structure prediction system

PubMed Central

2013-01-01

Background Predicting protein structure from sequence is one of the most significant and challenging problems in bioinformatics. Numerous bioinformatics techniques and tools have been developed to tackle almost every aspect of protein structure prediction ranging from structural feature prediction, template identification and query-template alignment to structure sampling, model quality assessment, and model refinement. How to synergistically select, integrate and improve the strengths of the complementary techniques at each prediction stage and build a high-performance system is becoming a critical issue for constructing a successful, competitive protein structure predictor. Results Over the past several years, we have constructed a standalone protein structure prediction system MULTICOM that combines multiple sources of information and complementary methods at all five stages of the protein structure prediction process including template identification, template combination, model generation, model assessment, and model refinement. The system was blindly tested during the ninth Critical Assessment of Techniques for Protein Structure Prediction (CASP9) in 2010 and yielded very good performance. In addition to studying the overall performance on the CASP9 benchmark, we thoroughly investigated the performance and contributions of each component at each stage of prediction. Conclusions Our comprehensive and comparative study not only provides useful and practical insights about how to select, improve, and integrate complementary methods to build a cutting-edge protein structure prediction system but also identifies a few new sources of information that may help improve the design of a protein structure prediction system. Several components used in the MULTICOM system are available at: http://sysbio.rnet.missouri.edu/multicom_toolbox/. PMID:23442819

Diagnostics in the Extendable Integrated Support Environment (EISE)

NASA Technical Reports Server (NTRS)

Brink, James R.; Storey, Paul

1988-01-01

Extendable Integrated Support Environment (EISE) is a real-time computer network consisting of commercially available hardware and software components to support systems level integration, modifications, and enhancement to weapons systems. The EISE approach offers substantial potential savings by eliminating unique support environments in favor of sharing common modules for the support of operational weapon systems. An expert system is being developed that will help support diagnosing faults in this network. This is a multi-level, multi-expert diagnostic system that uses experiential knowledge relating symptoms to faults and also reasons from structural and functional models of the underlying physical model when experiential reasoning is inadequate. The individual expert systems are orchestrated by a supervisory reasoning controller, a meta-level reasoner which plans the sequence of reasoning steps to solve the given specific problem. The overall system, termed the Diagnostic Executive, accesses systems level performance checks and error reports, and issues remote test procedures to formulate and confirm fault hypotheses.

Bacterial Reaction Centers Purified with Styrene Maleic Acid Copolymer Retain Native Membrane Functional Properties and Display Enhanced Stability**

PubMed Central

Swainsbury, David J K; Scheidelaar, Stefan; van Grondelle, Rienk; Killian, J Antoinette; Jones, Michael R

2014-01-01

Integral membrane proteins often present daunting challenges for biophysical characterization, a fundamental issue being how to select a surfactant that will optimally preserve the individual structure and functional properties of a given membrane protein. Bacterial reaction centers offer a rare opportunity to compare the properties of an integral membrane protein in different artificial lipid/surfactant environments with those in the native bilayer. Here, we demonstrate that reaction centers purified using a styrene maleic acid copolymer remain associated with a complement of native lipids and do not display the modified functional properties that typically result from detergent solubilization. Direct comparisons show that reaction centers are more stable in this copolymer/lipid environment than in a detergent micelle or even in the native membrane, suggesting a promising new route to exploitation of such photovoltaic integral membrane proteins in device applications. PMID:25212490

Assessing the integrity of spillway foundations

NASA Astrophysics Data System (ADS)

Hsu, Keng-Tsang; Chiang, Chih-Hung; Cheng, Chia-Chi

2017-02-01

The erosion under a spillway can be a long-term issue that threatens the structural integrity of a water reservoir. The spillways under investigation were suspected to be defective after they had been commissioned in 1987 and 1939, respectively. Potholes and subsurface cavities were confirmed in the safety assessment using various NDT techniques including ground penetrating radar and impact echo. The GPR inspection was able to differentiate the intact region from the cavities under concrete slabs. The impact echo results and associated analyses provided further evidence of inferior condition in the soil under the concrete slabs. The engineering team designed and executed the repair projects based on the conclusion of the integrity assessment. Repetitive GPR scans were also carried out after the rehabilitation of spillways. Not only the quality of repair can be evaluated, the scans also provided a baseline record for long-term condition assessment of the spillway and the reservoir in the future.

CSRQ: Communication-Efficient Secure Range Queries in Two-Tiered Sensor Networks

PubMed Central

Dai, Hua; Ye, Qingqun; Yang, Geng; Xu, Jia; He, Ruiliang

2016-01-01

In recent years, we have seen many applications of secure query in two-tiered wireless sensor networks. Storage nodes are responsible for storing data from nearby sensor nodes and answering queries from Sink. It is critical to protect data security from a compromised storage node. In this paper, the Communication-efficient Secure Range Query (CSRQ)—a privacy and integrity preserving range query protocol—is proposed to prevent attackers from gaining information of both data collected by sensor nodes and queries issued by Sink. To preserve privacy and integrity, in addition to employing the encoding mechanisms, a novel data structure called encrypted constraint chain is proposed, which embeds the information of integrity verification. Sink can use this encrypted constraint chain to verify the query result. The performance evaluation shows that CSRQ has lower communication cost than the current range query protocols. PMID:26907293

The Energy-Water-Food Nexus.

PubMed

Keairns, D L; Darton, R C; Irabien, A

2016-06-07

As the global population grows in size and increasingly lives in cities, and with lifestyles based on greater material consumption, more attention is being given to the integrated system that supplies our energy, water, and food, the Nexus. There is also mounting concern about effects on the Nexus of climate change and damage to the natural environment that provides essential ecosystem services. Nexus analysis applies existing techniques, such as computational modelling and Life Cycle Assessment, but new frameworks and tools are needed, including those that will integrate societal and technical dimensions. Case studies show the vital role played by stakeholder involvement in clarifying issues, priorities, and values. They also demonstrate the importance of an integrated systems view of the complex interrelationships of the Nexus when planning effective remedies. Assessments conclude that transformative social and political change is needed to create new structures, markets, and governance to deal with the Nexus if we are to meet agreed-upon sustainable development goals.

Cyclic voltammetry study of PEO processing of porous Ti and resulting coatings

NASA Astrophysics Data System (ADS)

Shbeh, Mohammed; Yerokhin, Aleksey; Goodall, Russell

2018-05-01

Ti is one of the most commonly used materials for biomedical applications. However, there are two issues associated with the use of it, namely its bio-inertness and high elastic modulus compared to the elastic modulus of the natural bone. Both of these hurdles could potentially be overcome by introducing a number of pores in the structure of the Ti implant to match the properties of the bone as well as improve the mechanical integration between the bone and implant, and subsequently coating it with a biologically active ceramic coating to promote chemical integration. Hence, in this study we investigated the usage of cyclic voltammetry in PEO treatment of porous Ti parts with different amount of porosity produced by both Metal Injection Moulding (MIM) and MIM in combination with a space holder. It was found that porous samples with higher porosity and open pores develop much thicker surface layers that penetrate through the inner structure of the samples forming a network of surface and subsurface coatings. The results are of potential benefit in producing surface engineered porous samples for biomedical applications which do not only address the stress shielding problem, but also improve the chemical integration.

Integrated design optimization research and development in an industrial environment

NASA Astrophysics Data System (ADS)

Kumar, V.; German, Marjorie D.; Lee, S.-J.

1989-04-01

An overview is given of a design optimization project that is in progress at the GE Research and Development Center for the past few years. The objective of this project is to develop a methodology and a software system for design automation and optimization of structural/mechanical components and systems. The effort focuses on research and development issues and also on optimization applications that can be related to real-life industrial design problems. The overall technical approach is based on integration of numerical optimization techniques, finite element methods, CAE and software engineering, and artificial intelligence/expert systems (AI/ES) concepts. The role of each of these engineering technologies in the development of a unified design methodology is illustrated. A software system DESIGN-OPT has been developed for both size and shape optimization of structural components subjected to static as well as dynamic loadings. By integrating this software with an automatic mesh generator, a geometric modeler and an attribute specification computer code, a software module SHAPE-OPT has been developed for shape optimization. Details of these software packages together with their applications to some 2- and 3-dimensional design problems are described.

Integrated design optimization research and development in an industrial environment

NASA Technical Reports Server (NTRS)

Kumar, V.; German, Marjorie D.; Lee, S.-J.

1989-01-01

An overview is given of a design optimization project that is in progress at the GE Research and Development Center for the past few years. The objective of this project is to develop a methodology and a software system for design automation and optimization of structural/mechanical components and systems. The effort focuses on research and development issues and also on optimization applications that can be related to real-life industrial design problems. The overall technical approach is based on integration of numerical optimization techniques, finite element methods, CAE and software engineering, and artificial intelligence/expert systems (AI/ES) concepts. The role of each of these engineering technologies in the development of a unified design methodology is illustrated. A software system DESIGN-OPT has been developed for both size and shape optimization of structural components subjected to static as well as dynamic loadings. By integrating this software with an automatic mesh generator, a geometric modeler and an attribute specification computer code, a software module SHAPE-OPT has been developed for shape optimization. Details of these software packages together with their applications to some 2- and 3-dimensional design problems are described.

An Assessment of Research Gaps Related to Deep Water Wellbore Integrity

NASA Astrophysics Data System (ADS)

Tkach, M. K.; Radonjic, M.; Kutchko, B. G.

2017-12-01

In order for a deep-water wellbore to uphold its integrity under high pressure - high temperature conditions, the wellbore must possess complete zonal isolation while surrounded in an extreme environment. Highly variable temperature and pressure ranges, shallow flow zones, as well as potentially corrosive fluids and gasses all present unique challenges to the job of the cement which maintains that zonal isolation. As such, alternative options to mainstream choices often present themselves as attractive avenues of discovery. As it is of utmost importance to maintain structural integrity under HPHT conditions, cement slurries are pumped downhole to provide zonal isolation and structural support to offshore wells. The wellbore system potentially faces a variety of temperature and pressure fluctuations from the immediate onset. These fluctuations may affect the hydration properties of the cement. It is also important to consider the chemical interactions that the cement may have at the rock-cement interface where potential degradation or annulus gaps may occur further risking a decrease in zonal isolation. This presentation intends to review some of the important issues regarding zonal isolation in HPHT conditions and to highlight critical knowledge gaps in order to generate important research questions.

Fuzzy Logic Module of Convolutional Neural Network for Handwritten Digits Recognition

NASA Astrophysics Data System (ADS)

Popko, E. A.; Weinstein, I. A.

2016-08-01

Optical character recognition is one of the important issues in the field of pattern recognition. This paper presents a method for recognizing handwritten digits based on the modeling of convolutional neural network. The integrated fuzzy logic module based on a structural approach was developed. Used system architecture adjusted the output of the neural network to improve quality of symbol identification. It was shown that proposed algorithm was flexible and high recognition rate of 99.23% was achieved.

Science for the changing Great Basin

USGS Publications Warehouse

Beever, Erik; Pyke, David A.

2004-01-01

The U.S. Geological Survey (USGS), with its multidisciplinary structure and role as a federal science organization, is well suited to provide integrated science in the Great Basin of the western United States. A research strategy developed by the USGS and collaborating partners addresses critical management issues in the basin, including invasive species, status and trends of wildlife populations and communities, wildfire, global climate change, and riparian and wetland habitats. Information obtained through implementation of this strategy will be important for decision-making by natural-resource managers.

Integrated orbital servicing study follow-on. Volume 2: Technical analysis and system design

NASA Technical Reports Server (NTRS)

1978-01-01

In-orbit service functional and physical requirements to support both low and high Earth orbit servicing/maintenance operations were defined, an optimum servicing system configuration was developed and mockups and early prototype hardware were fabricated to demonstrate and validate the concepts selected. Significant issues addressed include criteria for concept selection; representative mission equipment and approaches to their design for serviceability; significant serviceable spacecraft design aspects; servicer mechanism operation in one-g; approaches for the demonstration/simulation; and service mechanism structure design approach.

Development of a Rapidly Deployable Special Operations Component Command (SOCC) Core Concept for the North Atlantic Treaty Organization (NATO) Special Operations Headquarters (NSHQ)

DTIC Science & Technology

2011-12-01

operating in their territory. NSHQ is a new and evolving organization, which was instructed to develop a rapidly deployable HQ. NSHQ receives its...single overarching concept, eliminating redundancy, and integrates new deployable operational C2 structures (notably NSHQ) agreed through the...of the command and control issue is the ability to communicate effectively both up and down the chain of command. With the new technologies

An integrated methodology to assess the benefits of urban green space.

PubMed

De Ridder, K; Adamec, V; Bañuelos, A; Bruse, M; Bürger, M; Damsgaard, O; Dufek, J; Hirsch, J; Lefebre, F; Pérez-Lacorzana, J M; Thierry, A; Weber, C

2004-12-01

The interrelated issues of urban sprawl, traffic congestion, noise, and air pollution are major socioeconomic problems faced by most European cities. A methodology is currently being developed for evaluating the role of green space and urban form in alleviating the adverse effects of urbanisation, mainly focusing on the environment but also accounting for socioeconomic aspects. The objectives and structure of the methodology are briefly outlined and illustrated with preliminary results obtained from case studies performed on several European cities.

Special Focus

PubMed Central

Nawrocki, Eric P.; Burge, Sarah W.

2013-01-01

The development of RNA bioinformatic tools began more than 30 y ago with the description of the Nussinov and Zuker dynamic programming algorithms for single sequence RNA secondary structure prediction. Since then, many tools have been developed for various RNA sequence analysis problems such as homology search, multiple sequence alignment, de novo RNA discovery, read-mapping, and many more. In this issue, we have collected a sampling of reviews and original research that demonstrate some of the many ways bioinformatics is integrated with current RNA biology research. PMID:23948768

Usability and feasibility of a tablet-based Decision-Support and Integrated Record-keeping (DESIRE) tool in the nurse management of hypertension in rural western Kenya.

PubMed

Vedanthan, Rajesh; Blank, Evan; Tuikong, Nelly; Kamano, Jemima; Misoi, Lawrence; Tulienge, Deborah; Hutchinson, Claire; Ascheim, Deborah D; Kimaiyo, Sylvester; Fuster, Valentin; Were, Martin C

2015-03-01

Mobile health (mHealth) applications have recently proliferated, especially in low- and middle-income countries, complementing task-redistribution strategies with clinical decision support. Relatively few studies address usability and feasibility issues that may impact success or failure of implementation, and few have been conducted for non-communicable diseases such as hypertension. To conduct iterative usability and feasibility testing of a tablet-based Decision Support and Integrated Record-keeping (DESIRE) tool, a technology intended to assist rural clinicians taking care of hypertension patients at the community level in a resource-limited setting in western Kenya. Usability testing consisted of "think aloud" exercises and "mock patient encounters" with five nurses, as well as one focus group discussion. Feasibility testing consisted of semi-structured interviews of five nurses and two members of the implementation team, and one focus group discussion with nurses. Content analysis was performed using both deductive codes and significant inductive codes. Critical incidents were identified and ranked according to severity. A cause-of-error analysis was used to develop corresponding design change suggestions. Fifty-seven critical incidents were identified in usability testing, 21 of which were unique. The cause-of-error analysis yielded 23 design change suggestions. Feasibility themes included barriers to implementation along both human and technical axes, facilitators to implementation, provider issues, patient issues and feature requests. This participatory, iterative human-centered design process revealed previously unaddressed usability and feasibility issues affecting the implementation of the DESIRE tool in western Kenya. In addition to well-known technical issues, we highlight the importance of human factors that can impact implementation of mHealth interventions. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Usability and Feasibility of a Tablet-Based Decision-Support and Integrated Record-Keeping (DESIRE) Tool in the Nurse Management of Hypertension in Rural Western Kenya

PubMed Central

Vedanthan, Rajesh; Blank, Evan; Tuikong, Nelly; Kamano, Jemima; Misoi, Lawrence; Tulienge, Deborah; Hutchinson, Claire; Ascheim, Deborah D.; Kimaiyo, Sylvester; Fuster, Valentin; Were, Martin C.

2015-01-01

Background Mobile health (mHealth) applications have recently proliferated, especially in low- and middle-income countries, complementing task-redistribution strategies with clinical decision support. Relatively few studies address usability and feasibility issues that may impact success or failure of implementation, and few have been conducted for non-communicable diseases such as hypertension. Objective To conduct iterative usability and feasibility testing of a tablet-based Decision Support and Integrated Record-keeping (DESIRE) tool, a technology intended to assist rural clinicians taking care of hypertension patients at the community level in a resource-limited setting in western Kenya. Methods Usability testing consisted of “think aloud” exercises and “mock patient encounters” with five nurses, as well as one focus group discussion. Feasibility testing consisted of semi-structured interviews of five nurses and two members of the implementation team, and one focus group discussion with nurses. Content analysis was performed using both deductive codes and significant inductive codes. Critical incidents were identified and ranked according to severity. A cause-of-error analysis was used to develop corresponding design change suggestions. Results Fifty-seven critical incidents were identified in usability testing, 21 of which were unique. The cause-of-error analysis yielded 23 design change suggestions. Feasibility themes included barriers to implementation along both human and technical axes, facilitators to implementation, provider issues, patient issues and feature requests. Conclusions This participatory, iterative human-centered design process revealed previously unaddressed usability and feasibility issues affecting the implementation of the DESIRE tool in western Kenya. In addition to well-known technical issues, we highlight the importance of human factors that can impact implementation of mHealth interventions. PMID:25612791

Integrating an incident management system within a continuity of operations programme: case study of the Bank of Canada.

PubMed

Loop, Carole

2013-01-01

Carrying out critical business functions without interruption requires a resilient and robust business continuity framework. By embedding an industry-standard incident management system within its business continuity structure, the Bank of Canada strengthened its response plan by enabling timely response to incidents while maintaining a strong focus on business continuity. A total programme approach, integrating the two disciplines, provided for enhanced recovery capabilities. While the value of an effective and efficient response organisation is clear, as demonstrated by emergency events around the world, incident response structures based on normal operating hierarchy can experience unique challenges. The internationally-recognised Incident Command System (ICS) model addresses these issues and reflects the five primary incident management functions, each contributing to the overall strength and effectiveness of the response organisation. The paper focuses on the Bank of Canada's successful implementation of the ICS model as its incident management and continuity of operations programmes evolved to reflect current best practices.

Failure modes for pipelines in landslide areas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bruschi, R.; Spinazze, M.; Tomassini, D.

1995-12-31

In recent years a number of incidences of pipelines affected by slow soil movements have been reported in the relevant literature. Further related issues such as soil-pipe interaction have been studied both theoretically and through experimental surveys, along with the environmental conditions which are responsible for hazard to the pipeline integrity. A suitable design criteria under these circumstances has been discussed by several authors, in particular in relation to a limit state approach and hence a strain based criteria. The scope of this paper is to describe the failure mechanisms which may affect the pipeline in the presence of slowmore » soil movements impacting on the pipeline, both in the longitudinal and transverse direction. Particular attention is paid to environmental, geometric and structural parameters which steer the process towards one or other failure mechanism. Criteria for deciding upon remedial measures required to guarantee the structural integrity of the pipeline, both in the short and in the long term, are discussed.« less

Stress estimation in reservoirs using an integrated inverse method

NASA Astrophysics Data System (ADS)

Mazuyer, Antoine; Cupillard, Paul; Giot, Richard; Conin, Marianne; Leroy, Yves; Thore, Pierre

2018-05-01

Estimating the stress in reservoirs and their surroundings prior to the production is a key issue for reservoir management planning. In this study, we propose an integrated inverse method to estimate such initial stress state. The 3D stress state is constructed with the displacement-based finite element method assuming linear isotropic elasticity and small perturbations in the current geometry of the geological structures. The Neumann boundary conditions are defined as piecewise linear functions of depth. The discontinuous functions are determined with the CMA-ES (Covariance Matrix Adaptation Evolution Strategy) optimization algorithm to fit wellbore stress data deduced from leak-off tests and breakouts. The disregard of the geological history and the simplified rheological assumptions mean that only the stress field, statically admissible and matching the wellbore data should be exploited. The spatial domain of validity of this statement is assessed by comparing the stress estimations for a synthetic folded structure of finite amplitude with a history constructed assuming a viscous response.

Semiconductor activated terahertz metamaterials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Hou-Tong

Metamaterials have been developed as a new class of artificial effective media realizing many exotic phenomena and unique properties not normally found in nature. Metamaterials enable functionality through structure design, facilitating applications by addressing the severe material issues in the terahertz frequency range. Consequently, prototype functional terahertz devices have been demonstrated, including filters, antireflection coatings, perfect absorbers, polarization converters, and arbitrary wavefront shaping devices. Further integration of functional materials into metamaterial structures have enabled actively and dynamically switchable and frequency tunable terahertz metamaterials through the application of external stimuli. The enhanced light-matter interactions in active terahertz metamaterials may result inmore » unprecedented control and manipulation of terahertz radiation, forming the foundation of many terahertz applications. In this paper, we review the progress during the past few years in this rapidly growing research field. We particularly focus on the design principles and realization of functionalities using single-layer and few-layer terahertz planar metamaterials, and active terahertz metamaterials through the integration of semiconductors to achieve switchable and frequency-tunable response.« less

Semiconductor activated terahertz metamaterials

DOE PAGES

Chen, Hou-Tong

2014-08-01

Metamaterials have been developed as a new class of artificial effective media realizing many exotic phenomena and unique properties not normally found in nature. Metamaterials enable functionality through structure design, facilitating applications by addressing the severe material issues in the terahertz frequency range. Consequently, prototype functional terahertz devices have been demonstrated, including filters, antireflection coatings, perfect absorbers, polarization converters, and arbitrary wavefront shaping devices. Further integration of functional materials into metamaterial structures have enabled actively and dynamically switchable and frequency tunable terahertz metamaterials through the application of external stimuli. The enhanced light-matter interactions in active terahertz metamaterials may result inmore » unprecedented control and manipulation of terahertz radiation, forming the foundation of many terahertz applications. In this paper, we review the progress during the past few years in this rapidly growing research field. We particularly focus on the design principles and realization of functionalities using single-layer and few-layer terahertz planar metamaterials, and active terahertz metamaterials through the integration of semiconductors to achieve switchable and frequency-tunable response.« less

Issues in Integrating Information Technology in Learning and Teaching EFL: The Saudi Experience

ERIC Educational Resources Information Center

Al-Maini, Yousef Hamad

2013-01-01

The Saudi education system is facing a climate of change characterized by an interest in integrating new technology and educational approaches to improve teaching and learning. In this climate, the present paper explores the issues in integrating information technology in learning and teaching English as a foreign language (EFL) in government…

Integrating knowledge and control into hypermedia-based training environments: Experiments with HyperCLIPS

NASA Technical Reports Server (NTRS)

Hill, Randall W., Jr.

1990-01-01

The issues of knowledge representation and control in hypermedia-based training environments are discussed. The main objective is to integrate the flexible presentation capability of hypermedia with a knowledge-based approach to lesson discourse management. The instructional goals and their associated concepts are represented in a knowledge representation structure called a 'concept network'. Its functional usages are many: it is used to control the navigation through a presentation space, generate tests for student evaluation, and model the student. This architecture was implemented in HyperCLIPS, a hybrid system that creates a bridge between HyperCard, a popular hypertext-like system used for building user interfaces to data bases and other applications, and CLIPS, a highly portable government-owned expert system shell.

Fulfilling institutional responsibilities in health care: organizational ethics and the role of mission discernment.

PubMed

Gallagher, John A; Goodstein, Jerry

2002-10-01

In this paper we highlight the emergence of organizational ethics issues in health care as an important outcome of the changing structure of health care delivery. We emphasize three core themes related to business ethics and health care ethics: integrity, responsibility, and choice. These themes are brought together in a discussion of the process of Mission Discernment as it has been developed and implemented within an integrated health care system. Through this discussion we highlight how processes of institutional reflection, such as Mission Discernment, can help health care organizations, as well as corporations, make critical choices in turbulent environments that further the core mission and values and fulfill institutional responsibilities to a broad range of stakeholders.

Integrated deterministic and probabilistic safety analysis for safety assessment of nuclear power plants

DOE PAGES

Di Maio, Francesco; Zio, Enrico; Smith, Curtis; ...

2015-07-06

The present special issue contains an overview of the research in the field of Integrated Deterministic and Probabilistic Safety Assessment (IDPSA) of Nuclear Power Plants (NPPs). Traditionally, safety regulation for NPPs design and operation has been based on Deterministic Safety Assessment (DSA) methods to verify criteria that assure plant safety in a number of postulated Design Basis Accident (DBA) scenarios. Referring to such criteria, it is also possible to identify those plant Structures, Systems, and Components (SSCs) and activities that are most important for safety within those postulated scenarios. Then, the design, operation, and maintenance of these “safety-related” SSCs andmore » activities are controlled through regulatory requirements and supported by Probabilistic Safety Assessment (PSA).« less

[Mercosur's regional health agenda: architecture and themes].

PubMed

Queiroz, Luisa Guimaraes; Giovanella, Ligia

2011-08-01

This article describes the shaping of institutional health spaces in the Mercosur, with analysis of themes and results and considerations on the construction of the regional agenda and on the effects of regional economic integration processes on health policies and systems. We discuss the organization, operation, focus topics, and results achieved in specific health forums (Meeting of Ministers of Health and Sub-Working Group 11), seeking to analyze the architecture and issues addressed by the regional agenda and drawing parallels with the European experience. The aim of this reflection is to identify how the work done by Mercosur structures contributes to building a regional agenda, with the expectation that the integration can contribute to reducing inequalities in access to health care in the region.

Everyday robotic action: lessons from human action control

PubMed Central

de Kleijn, Roy; Kachergis, George; Hommel, Bernhard

2014-01-01

Robots are increasingly capable of performing everyday human activities such as cooking, cleaning, and doing the laundry. This requires the real-time planning and execution of complex, temporally extended sequential actions under high degrees of uncertainty, which provides many challenges to traditional approaches to robot action control. We argue that important lessons in this respect can be learned from research on human action control. We provide a brief overview of available psychological insights into this issue and focus on four principles that we think could be particularly beneficial for robot control: the integration of symbolic and subsymbolic planning of action sequences, the integration of feedforward and feedback control, the clustering of complex actions into subcomponents, and the contextualization of action-control structures through goal representations. PMID:24672474

Environmental performance and financial report integrity: challenges for the mining sector in Indonesia

NASA Astrophysics Data System (ADS)

Mayangsari, S.

2018-01-01

This study investigates the influence of environmental performance on the financial report integrity. The statistics used were primary data from interviews with senior members of the mining sector regarding environmental issues, as well as secondary data using Financial Report 2016. The samples were listed mining companies with semester data. Questionnaires were used to measure their perceptions of the challenges concerning climate change faced by the mining sector. The results of this research show that regulatory interventions will be critical to environmental issues. This study employed KLD as a proxy for environmental performance, correlated with other variables regarding the integrity of disclosure. The outcome indicates that environmental issues will increase the integrity of financial reports.

Transition from Nondestructive Testing (NDT) to Structural Health Monitoring (SHM): potential and challenges (presentation video)

NASA Astrophysics Data System (ADS)

Cawley, Peter

2014-03-01

There is a gradual shift in emphasis from periodic inspection with detachable transducers (NDT) to permanently installed monitoring systems giving information about the structural integrity at pre-programmed intervals or on demand (SHM). The drivers of this change are discussed, together with the requirements of successful SHM systems. Particular issues are that NDT often involves scanning and this is not possible with typical SHM configurations; it therefore becomes important to cover a significant area of structure from each transducer position. Guided waves provide a possible solution to this problem and permanently installed guided wave pipe inspection systems are now available. The sensitivity obtained with a permanently installed system is significantly better than that in a one-off test as baseline subtraction can be employed. However, this is far from trivial as it is necessary to compensate for benign changes such as temperature. The guided wave technique does not provide accurate remaining thickness information and is best complemented by point measurements at selected locations. Another issue is that the SHM transducers must survive in operational conditions, which is particularly difficult at high temperatures. Recent work at Imperial College and associated spin-out companies on solutions to these problems is discussed.

Dynamic mobility application policy analysis : policy and institutional issues for Integrated Dynamic Transit Operations (IDTO).

DOT National Transportation Integrated Search

2015-07-01

This report documents policy considerations for Integrate Dynamic Transit (IDTO). IDTO applications provide individualized trip planning, transfer protection, and ridesharing options. The analysis identified the following potential policy issues: dat...

Lead exposure reduces sperm quality and DNA integrity in mice.

PubMed

Li, Cuiling; Zhao, Kai; Zhang, Huiping; Liu, Lili; Xiong, Fei; Wang, Kunyu; Chen, Biao

2018-05-01

Toxicity of lead on male reproductive functions has raised wide public concern as environmental lead contamination remains common worldwide. Conflicting and controversial data are available regarding effects of lead on male fertility. More importantly, our knowledge on effects of lead on sperm DNA integrity is significantly limited. Thus, further studies should focus on this issue. In the current study, adult male mice were exposed to a series of lead acetate concentrations in drinking water for six weeks. Following administration, lead levels in blood, testicles, and epididymis were measured, and potential changes in morphology of testis and epididymis due to lead exposure were identified. We also analyzed sperm parameters, including sperm density, viability, motility, and morphology, to evaluate quality of sperm collected from epididymis. Especially, hypothetical influence of lead on sperm DNA integrity was also evaluated by terminal deoxynucleotidyltransferase-mediated dUTP-biotin nick end labeling, alkaline comet assay, and sperm chromatin structure assay. Lead exposure possibly exerted no effect on growth of mice because these animals acquired similar body weight gain during the experimental period. However, high lead concentrations (0.5% and 1%) in drinking water affected sperm motility and increased percentage of spermatozoa with abnormal morphology. In groups treated with 0.25%, 0.5%, and 1% lead acetate, percentages of sperm cells showing DNA breaks and chromatin structure damage significantly increased. Altogether, lead exposure not only exhibits adverse effects on sperm physiological parameters, but also impairs DNA structure and integrity. These effects may lead to significant decline in male fertility. © 2018 Wiley Periodicals, Inc.

System-on-Chip Considerations for Heterogeneous Integration of CMOS and Fluidic Bio-Interfaces.

PubMed

Datta-Chaudhuri, Timir; Smela, Elisabeth; Abshire, Pamela A

2016-12-01

CMOS chips are increasingly used for direct sensing and interfacing with fluidic and biological systems. While many biosensing systems have successfully combined CMOS chips for readout and signal processing with passive sensing arrays, systems that co-locate sensing with active circuits on a single chip offer significant advantages in size and performance but increase the complexity of multi-domain design and heterogeneous integration. This emerging class of lab-on-CMOS systems also poses distinct and vexing technical challenges that arise from the disparate requirements of biosensors and integrated circuits (ICs). Modeling these systems must address not only circuit design, but also the behavior of biological components on the surface of the IC and any physical structures. Existing tools do not support the cross-domain simulation of heterogeneous lab-on-CMOS systems, so we recommend a two-step modeling approach: using circuit simulation to inform physics-based simulation, and vice versa. We review the primary lab-on-CMOS implementation challenges and discuss practical approaches to overcome them. Issues include new versions of classical challenges in system-on-chip integration, such as thermal effects, floor-planning, and signal coupling, as well as new challenges that are specifically attributable to biological and fluidic domains, such as electrochemical effects, non-standard packaging, surface treatments, sterilization, microfabrication of surface structures, and microfluidic integration. We describe these concerns as they arise in lab-on-CMOS systems and discuss solutions that have been experimentally demonstrated.

Special issue on cluster algebras in mathematical physics

NASA Astrophysics Data System (ADS)

Di Francesco, Philippe; Gekhtman, Michael; Kuniba, Atsuo; Yamazaki, Masahito

2013-10-01

This is a call for contributions to a special issue of Journal of Physics A: Mathematical and Theoretical dedicated to cluster algebras in mathematical physics. Over the ten years since their introduction by Fomin and Zelevinsky, the theory of cluster algebras has witnessed a spectacular growth, first and foremost due to the many links that have been discovered with a wide range of subjects in mathematics and, increasingly, theoretical and mathematical physics. The main motivation of this special issue is to gather together reviews, recent developments and open problems, mainly from a mathematical physics viewpoint, into a single comprehensive issue. We expect that such a special issue will become a valuable reference for the broad scientific community working in mathematical and theoretical physics. The issue will consist of invited review articles and contributed papers containing new results on the interplays of cluster algebras with mathematical physics. Editorial policy The Guest Editors for this issue are Philippe Di Francesco, Michael Gekhtman, Atsuo Kuniba and Masahito Yamazaki. The areas and topics for this issue include, but are not limited to: discrete integrable systems arising from cluster mutations cluster structure on Poisson varieties cluster algebras and soliton interactions cluster positivity conjecture Y-systems in the thermodynamic Bethe ansatz and Zamolodchikov's periodicity conjecture T-system of transfer matrices of integrable lattice models dilogarithm identities in conformal field theory wall crossing in 4d N = 2 supersymmetric gauge theories 4d N = 1 quiver gauge theories described by networks scattering amplitudes of 4d N = 4 theories 3d N = 2 gauge theories described by flat connections on 3-manifolds integrability of dimer/Ising models on graphs. All contributions will be refereed and processed according to the usual procedure of the journal. Guidelines for preparation of contributions The deadline for contributed papers is 31 March 2014. This deadline will allow the special issue to appear at the end of 2014. There is no strict regulation on article size, but as a guide the preferable size is 15-30 pages for contributed papers and 40-60 pages for reviews. Further advice on publishing your work in Journal of Physics A may be found at iopscience.iop.org/jphysa. Contributions to the special issue should be submitted by web upload via authors.iop.org/, or by email to jphysa@iop.org, quoting 'JPhysA special issue on cluster algebras in mathematical physics'. Submissions should ideally be in standard LaTeX form. Please see the website for further information on electronic submissions. All contributions should be accompanied by a read-me file or covering letter giving the postal and e-mail addresses for correspondence. The Publishing Office should be notified of any subsequent change of address. The special issue will be published in the print and online versions of the journal.

Controllability of multi-agent systems with time-delay in state and switching topology

NASA Astrophysics Data System (ADS)

Ji, Zhijian; Wang, Zidong; Lin, Hai; Wang, Zhen

2010-02-01

In this article, the controllability issue is addressed for an interconnected system of multiple agents. The network associated with the system is of the leader-follower structure with some agents taking leader role and others being followers interconnected via the neighbour-based rule. Sufficient conditions are derived for the controllability of multi-agent systems with time-delay in state, as well as a graph-based uncontrollability topology structure is revealed. Both single and double integrator dynamics are considered. For switching topology, two algebraic necessary and sufficient conditions are derived for the controllability of multi-agent systems. Several examples are also presented to illustrate how to control the system to shape into the desired configurations.

A Methodological Framework for Enterprise Information System Requirements Derivation

NASA Astrophysics Data System (ADS)

Caplinskas, Albertas; Paškevičiūtė, Lina

Current information systems (IS) are enterprise-wide systems supporting strategic goals of the enterprise and meeting its operational business needs. They are supported by information and communication technologies (ICT) and other software that should be fully integrated. To develop software responding to real business needs, we need requirements engineering (RE) methodology that ensures the alignment of requirements for all levels of enterprise system. The main contribution of this chapter is a requirement-oriented methodological framework allowing to transform business requirements level by level into software ones. The structure of the proposed framework reflects the structure of Zachman's framework. However, it has other intentions and is purposed to support not the design but the RE issues.

Overview of mechanics of materials branch activities in the computational structures area

NASA Technical Reports Server (NTRS)

Poe, C. C., Jr.

1992-01-01

Base programs and system programs are discussed. The base programs include fundamental research of composites and metals for airframes leading to characterization of advanced materials, models of behavior, and methods for predicting damage tolerance. Results from the base programs support the systems programs, which change as NASA's missions change. The National Aerospace Plane (NASP), Advanced Composites Technology (ACT), Airframe Structural Integrity Program (Aging Aircraft), and High Speed Research (HSR) programs are currently being supported. Airframe durability is one of the key issues in each of these system programs. The base program has four major thrusts, which will be reviewed subsequently. Additionally, several technical highlights will be reviewed for each thrust.

System Engineering and Integration of Controls for Advanced Life Support

NASA Technical Reports Server (NTRS)

Overland, David; Hoo, Karlene; Ciskowski, Marvin

2006-01-01

The Advanced Integration Matrix (AIM) project at the Johnson Space Center (JSC) was chartered to study and solve systems-level integration issues for exploration missions. One of the first issues identified was an inability to conduct trade studies on control system architectures due to the absence of mature evaluation criteria. Such architectures are necessary to enable integration of regenerative life support systems. A team was formed to address issues concerning software and hardware architectures and system controls.. The team has investigated what is required to integrate controls for the types of non-linear dynamic systems encountered in advanced life support. To this end, a water processing bioreactor testbed is being developed which will enable prototyping and testing of integration strategies and technologies. Although systems such as the water bioreactors exhibit the complexities of interactions between control schemes most vividly, it is apparent that this behavior and its attendant risks will manifest itself among any set of interdependent autonomous control systems. A methodology for developing integration requirements for interdependent and autonomous systems is a goal of this team and this testbed. This paper is a high-level summary of the current status of the investigation, the issues encountered, some tentative conclusions, and the direction expected for further research.

Integrating Technologies in Higher Education: The Issue of Recommended Educational Features Still Making Headline News

ERIC Educational Resources Information Center

Amemado, Dodzi

2014-01-01

The integration of technology in higher education has been swiftly changing since 2000. This study, which focused on issues related to technology integration in higher education, included 24 interviews done in 15 universities. The interviews documented an accelerated pace of change as well a wide range of innovations. Relying on the idea that…

High Schoolers' Views on Academic Integrity

ERIC Educational Resources Information Center

Bacha, Nahla Nola; Bahous, Rima; Nabhani, Mona

2012-01-01

The issue of academic integrity in cheating on exams and plagiarising in writing is not a new one. All schools need to address this problem and some more than others. In the L2 context, the issues become more complex as non-native students need to adhere to the "culture of learning" of a Western model of academic integrity if they are to…

Problems in cross-cultural use of the hospital anxiety and depression scale: "no butterflies in the desert".

PubMed

Maters, Gemma A; Sanderman, Robbert; Kim, Aimee Y; Coyne, James C

2013-01-01

The Hospital Anxiety and Depression Scale (HADS) is widely used to screen for anxiety and depression. A large literature is citable in support of its validity, but difficulties are increasingly being identified, such as inexplicably discrepant optimal cutpoints and inconsistent factor-structures. This article examines whether these problems could be due to the construction of the HADS that poses difficulties for translation and cross-cultural use. Authors' awareness of difficulties translating the HADS were identified by examining 20% of studies using the HADS, obtained by a systematic literature search in Pubmed and PsycINFO in May 2012. Reports of use of translations and validation studies were recorded for papers from non-English speaking countries. Narrative and systematic reviews were examined for how authors dealt with different translations. Of 417 papers from non-English speaking countries, only 45% indicated whether a translation was used. Studies validating translations were cited in 54%. Seventeen reviews, incorporating data from diverse translated versions, were examined. Only seven mentioned issues of language and culture, and none indicated insurmountable problems in integrating results from different translations. Initial decisions concerning item content and response options likely leave the HADS difficult to translate, but we failed to find an acknowledgment of problems in articles involving its translation and cross-cultural use. Investigators' lack of awareness of these issues can lead to anomalous results and difficulties in interpretation and integration of these results. Reviews tend to overlook these issues and most reviews indiscriminately integrate results from studies performed in different countries. Cross-culturally valid, but literally translated versions of the HADS may not be attainable, and specific cutpoints may not be valid across cultures and language. Claims about rates of anxiety and depression based on integrating cross-cultural data or using the same cutpoint across languages and culture should be subject to critical scrutiny.

Problems in Cross-Cultural Use of the Hospital Anxiety and Depression Scale: “No Butterflies in the Desert”

PubMed Central

Maters, Gemma A.; Sanderman, Robbert; Kim, Aimee Y.; Coyne, James C.

2013-01-01

Objective The Hospital Anxiety and Depression Scale (HADS) is widely used to screen for anxiety and depression. A large literature is citable in support of its validity, but difficulties are increasingly being identified, such as inexplicably discrepant optimal cutpoints and inconsistent factor-structures. This article examines whether these problems could be due to the construction of the HADS that poses difficulties for translation and cross-cultural use. Methods Authors’ awareness of difficulties translating the HADS were identified by examining 20% of studies using the HADS, obtained by a systematic literature search in Pubmed and PsycINFO in May 2012. Reports of use of translations and validation studies were recorded for papers from non-English speaking countries. Narrative and systematic reviews were examined for how authors dealt with different translations. Results Of 417 papers from non-English speaking countries, only 45% indicated whether a translation was used. Studies validating translations were cited in 54%. Seventeen reviews, incorporating data from diverse translated versions, were examined. Only seven mentioned issues of language and culture, and none indicated insurmountable problems in integrating results from different translations. Conclusion Initial decisions concerning item content and response options likely leave the HADS difficult to translate, but we failed to find an acknowledgment of problems in articles involving its translation and cross-cultural use. Investigators’ lack of awareness of these issues can lead to anomalous results and difficulties in interpretation and integration of these results. Reviews tend to overlook these issues and most reviews indiscriminately integrate results from studies performed in different countries. Cross-culturally valid, but literally translated versions of the HADS may not be attainable, and specific cutpoints may not be valid across cultures and language. Claims about rates of anxiety and depression based on integrating cross-cultural data or using the same cutpoint across languages and culture should be subject to critical scrutiny. PMID:23976969

"It was the whole picture" a mixed methods study of successful components in an integrated wellness service in North East England.

PubMed

Cheetham, M; Van der Graaf, P; Khazaeli, B; Gibson, E; Wiseman, A; Rushmer, R

2018-03-22

A growing number of Local Authorities (LAs) have introduced integrated wellness services as part of efforts to deliver cost effective, preventive services that address the social determinants of health. This study examined which elements of an integrated wellness service in the north east of England were effective in improving health and wellbeing (HWB). The study used a mixed-methods approach. In-depth semi-structured interviews (IVs) were conducted with integrated wellness service users (n = 25) and focus groups (FGs) with group based service users (n = 14) and non-service users (n = 23) to gather the views of stakeholders. Findings are presented here alongside analysis of routine monitoring data. The different data were compared to examine what each data source revealed about the effectiveness of the service. Findings suggest that integrated wellness services work by addressing the social determinants of health and respond to multiple complex health and social concerns rather than single issues. The paper identifies examples of 'active ingredients' at the heart of the programme, such as sustained relationships, peer support and confidence building, as well as the activities through which changes take place, such as sports and leisure opportunities which in turn encourage social interaction. Wider wellbeing outcomes, including reduced social isolation and increased self-efficacy are also reported. Practical and motivational support helped build community capacity by encouraging community groups to access funding, helped navigate bureaucratic systems, and promoted understanding of marginalised communities. Fully integrated wellness services could support progression opportunities through volunteering and mentoring. An integrated wellness service that offers a holistic approach was valued by service users and allowed them to address complex issues simultaneously. Few of the reported health gains were captured in routine data. Quantitative and qualitative data each offered a partial view of how effectively services were working.

Fuel containment and damage tolerance in large composite primary aircraft structures. Phase 2: Testing

NASA Technical Reports Server (NTRS)

Sandifer, J. P.; Denny, A.; Wood, M. A.

1985-01-01

Technical issues associated with fuel containment and damage tolerance of composite wing structures for transport aircraft were investigated. Material evaluation tests were conducted on two toughened resin composites: Celion/HX1504 and Celion/5245. These consisted of impact, tension, compression, edge delamination, and double cantilever beam tests. Another test series was conducted on graphite/epoxy box beams simulating a wing cover to spar cap joint configuration of a pressurized fuel tank. These tests evaluated the effectiveness of sealing methods with various fastener types and spacings under fatigue loading and with pressurized fuel. Another test series evaluated the ability of the selected coatings, film, and materials to prevent fuel leakage through 32-ply AS4/2220-1 laminates at various impact energy levels. To verify the structural integrity of the technology demonstration article structural details, tests were conducted on blade stiffened panels and sections. Compression tests were performed on undamaged and impacted stiffened AS4/2220-1 panels and smaller element tests to evaluate stiffener pull-off, side load and failsafe properties. Compression tests were also performed on panels subjected to Zone 2 lightning strikes. All of these data were integrated into a demonstration article representing a moderately loaded area of a transport wing. This test combined lightning strike, pressurized fuel, impact, impact repair, fatigue and residual strength.

Novel monolithic integration scheme for high-speed electroabsorption modulators and semiconductor optical amplifiers using cascaded structure.

PubMed

Lin, Fang-Zheng; Wu, Tsu-Hsiu; Chiu, Yi-Jen

2009-06-08

A new monolithic integration scheme, namely cascaded-integration (CI), for improving high-speed optical modulation is proposed and demonstrated. High-speed electroabsorption modulators (EAMs) and semiconductor optical amplifiers (SOAs) are taken as the integrated elements of CI. This structure is based on an optical waveguide defined by cascading segmented EAMs with segmented SOAs, while high-impedance transmission lines (HITLs) are used for periodically interconnecting EAMs, forming a distributive optical re-amplification and re-modulation. Therefore, not only the optical modulation can be beneficial from SOA gain, but also high electrical reflection due to EAM low characteristic impedance can be greatly reduced. Two integration schemes, CI and conventional single-section (SS), with same total EAM- and SOA- lengths are fabricated and compared to examine the concept. Same modulation-depth against with EAM bias (up to 5V) as well as SOA injection current (up to 60mA) is found in both structures. In comparison with SS, a < 1dB extra optical-propagation loss in CI is measured due to multi-sections of electrical-isolation regions between EAMs and SOAs, suggesting no significant deterioration in CI on DC optical modulation efficiency. Lower than -12dB of electrical reflection from D.C. to 30GHz is observed in CI, better than -5dB reflection in SS for frequency of above 5GHz. Superior high-speed electrical properties in CI structure can thus lead to higher speed of electrical-to-optical (EO) response, where -3dB bandwidths are >30GHz and 13GHz for CI and SS respectively. Simulation results on electrical and EO response are quite consistent with measurement, confirming that CI can lower the driving power at high-speed regime, while the optical loss is still kept the same level. Taking such distributive advantage (CI) with optical gain, not only higher-speed modulation with high output optical power can be attained, but also the trade-off issue due to impedance mismatch can be released to reduce the driving power of modulator. Such kind of monolithic integration scheme also has potential for the applications of other high-speed optoelectronics devices.

Integrating Remote Sensing Data with Socioeconomic Data: Sensitivity, Confidentiality, Privacy, and Intellectual Property Challenges

NASA Astrophysics Data System (ADS)

Downs, R. R.; Adamo, S. B.

2014-12-01

The integration of remote sensing data with socioeconomic data presents new opportunities for scientific discovery and analysis that can improve understanding of the environmental sustainability issues that society faces today. Such integrated data products and services can be used to study interdisciplinary issues by investigators representing various disciplines. In addition to the scientific benefits that can be attained by integrating remote sensing data with socioeconomic data, the integration of these data also present challenges that reflect the complex issues that arise when sharing and integrating different types of science data. When integrating one or more datasets that contain sensitive information, data producers need to be aware of the limitations that have been placed upon the data to protect private property, species or other inhabitants that reside on the property, or restricted information about a particular location. Similarly, confidentiality and privacy issues are a concern for data that have been collected about individual humans and families who have volunteered to serve as human research subjects or whose personal information may have been collected without their knowledge. In addition, intellectual property rights that are associated with a particular dataset may prevent integration with other data or pose constraints on the use of the resulting data products or services. These challenges will be described along with approaches that can be applied to address them when planning projects that involve the integration of remote sensing data with socioeconomic data.

Integration Issues of Cells into Battery Packs for Plug-in and Hybrid Electric Vehicles: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pesaran, A. A.; Kim, G. H.; Keyser, M.

2009-05-01

The main barriers to increased market share of hybrid electric vehicles (HEVs) and commercialization of plug-in HEVs are the cost, safety, and life of lithium ion batteries. Significant effort is being directed to address these issues for lithium ion cells. However, even the best cells may not perform as well when integrated into packs for vehicles because of the environment in which vehicles operate. This paper discusses mechanical, electrical, and thermal integration issues and vehicle interface issues that could impact the cost, life, and safety of the system. It also compares the advantages and disadvantages of using many small cellsmore » versus a few large cells and using prismatic cells versus cylindrical cells.« less

Integrating community health workers into a patient-centered medical home to support disease self-management among Vietnamese Americans: lessons learned.

PubMed

Wennerstrom, Ashley; Bui, Tap; Harden-Barrios, Jewel; Price-Haywood, Eboni G

2015-01-01

There is evidence that patient-centered medical homes (PCMHs) and community health workers (CHWs) improve chronic disease management. There are few models for integrating CHWs into PCMHs in order to enhance disease self-management support among diverse populations. In this article, we describe how a community-based nonprofit agency, a PCMH, and academic partners collaborated to develop and implement the Patient Resource and Education Program (PREP). We employed CHWs as PCMH care team members to provide health education and support to Vietnamese American patients with uncontrolled diabetes and/or hypertension. We began by conducting focus groups to assess patient knowledge, desire for support, and availability of community resources. Based on findings, we developed PREP with CHW guidance on cultural tailoring of educational materials and methods. CHWs received training in core competencies related to self-management support principles and conducted the 4-month intervention for PCMH patients. Throughout the program, we conducted process evaluation through structured team meetings and patient satisfaction surveys. We describe successes and challenges associated with PREP delivery including patient recruitment, structuring/documenting visits, and establishing effective care team integration, work flow, and communication. Strategies for mitigating these issues are presented, and we make recommendations for other PCMHs seeking to integrate CHWs into care teams. © 2014 Society for Public Health Education.

Advances in lasers and optical micro-nano-systems

NASA Astrophysics Data System (ADS)

Laurell, F.; Fazio, E.

2010-09-01

Lasers represent a well consolidated technology: nevertheless, research in this field remains very active and productive, in both basic and applied directions. At the moment significant attention is given to those sources that bring together high power and compactness. Such high power lasers find important applications for material treatments and such applications are presented by Ehsani et al and Saiedeh Saghafi et al, in the treatment of dielectric thin films (Alteration of optical and morphological properties of polycarbonate illuminated by visible/IR laser beams) or of biological tissues like pistachio seeds (Investigating the effects of laser beams (532 and 660 nm) in annihilation of pistachio mould fungus using spectrophotometry analysis). In particular the latter paper show how laser sources can find very important applications in new domains, preserving goods and food without the need for preservatives or pesticides by simply sterilizing them using light. Optical Micro and Nano Systems presents a new domain for exploration. In this framework this special issue is very attractive, because it assembles papers reporting new results in three directions: new techniques for monitoring integrated micro- and nano-systems, new integrated systems and novel high performance metamaterial configurations. Integrated micro-components can be monitored and controlled using reflectance measurements as presented by Piombini et al (Toward the reflectance measurement of micro components). Speckle formation during laser beam reflection can also be a very sophisticated tool for detecting ultra-precise displacements, as presented by Filter et al (High resolution displacement detection with speckles : accuracy limits in linear displacement speckle metrology). Three dimensional integrated optical structures is indeed a big challenge and a peculiarity of photonics, they can be formed through traditional holography or using more sophisticated and novel ! technologies. Thus, special manipulation of the writing-reading optical beam can push holography toward storages at higher data densities, as presented by Norihiko Ishii et al (Wavefront compensation method using novel index in holographic data storage). Along a similar direction Furlan et al describe a very innovative technique for producing optical traps using novel Devil micro-lenses (Volumetric multiple optical traps produced by Devil's lenses). Vynnyk et al presented an interesting application of electron microscopy for monitoring sub-micrometric structures in 3D configurations (3D-measurement with the stereo scanning electron microscope on sub-micrometer structure). Finally, S. Rao et al present two interesting papers on integrated structures compatible with silicon technology: one describes the realisation of low-loss waveguides using amorphous silicon, a relatively novel material with many applications in very different domains (Low-loss amorphous silicon waveguid! es grown by PECVD on indium tin oxide), and one on the realisation of a electrically drivable device with affective compatibility with CMOS technology (Electro-optical modulating multistack device based on the CMOS-compatible technology of amorphous silicon). We hope that this special issue of the Journal of the European Optical Society will reflect the interest of the European Scientific Community toward these fundamental and applied topics and will demonstrate to readers some of the actual directions of research. We express our full appreciation to the authors that participated to this initiative which acts only as a primer for the vast amount of work now being undertaken in laser physics and applications in micro- and nano-systems. We would like to give a special thank to the paper reviewers for their important role in the paper selection process and all the journal staff for their very professional support, dedication and energy, which made this special issue feasible.

Cultural competency training for public health students: integrating self, social, and global awareness into a master of public health curriculum.

PubMed

Cushman, Linda F; Delva, Marlyn; Franks, Cheryl L; Jimenez-Bautista, Ana; Moon-Howard, Joyce; Glover, Jim; Begg, Melissa D

2015-03-01

Cultural competency training in public health, medicine, social work, nursing, dental medicine, and other health professions has been a topic of increasing interest and significance. Despite the now burgeoning literature that describes specific knowledge, attitudes, and skills that promote cultural "competence," fully defining this complex, multidimensional term and implementing activities to enhance it remain a challenge. We describe our experiences in introducing a mandatory, full-day workshop to incoming Master of Public Health students, called "Self, Social, and Global Awareness: Personal Capacity Building for Professional Education and Practice." The purpose of the program is to provide a meaningful, structured environment to explore issues of culture, power, privilege, and social justice, emphasizing the centrality of these issues in effective public health education and practice.

Methods for the Scientific Study of Discrimination and Health: An Ecosocial Approach

PubMed Central

2012-01-01

The scientific study of how discrimination harms health requires theoretically grounded methods. At issue is how discrimination, as one form of societal injustice, becomes embodied inequality and is manifested as health inequities. As clarified by ecosocial theory, methods must address the lived realities of discrimination as an exploitative and oppressive societal phenomenon operating at multiple levels and involving myriad pathways across both the life course and historical generations. An integrated embodied research approach hence must consider (1) the structural level—past and present de jure and de facto discrimination; (2) the individual level—issues of domains, nativity, and use of both explicit and implicit discrimination measures; and (3) how current research methods likely underestimate the impact of racism on health. PMID:22420803

Smurf2 Regulates DNA Repair and Packaging to Prevent Tumors | Center for Cancer Research

Cancer.gov

The blueprint for all of a cell’s functions is written in the genetic code of DNA sequences as well as in the landscape of DNA and histone modifications. DNA is wrapped around histones to package it into chromatin, which is stored in the nucleus. It is important to maintain the integrity of the chromatin structure to ensure that the cell continues to behave appropriately. Recently, Ying Zhang, Ph.D., Senior Investigator in CCR’s Laboratory of Cellular and Molecular Biology, and her colleagues showed that alterations in the organization of the DNA can lead to tumor growth in a variety of tissues. This study appeared in the February 2012 issue of Nature Medicine and was featured as a cover story of that issue.

Coleman Advocates for Children And Youth: a pioneering child advocacy organization (1974-2008).

PubMed

Carnochan, Sarah; Austin, Michael J

2011-01-01

Coleman Advocates for Youth and Children is a pioneering 30-year-old child advocacy organization founded by several affluent community members and children's service professionals to stop housing abused and neglected children in juvenile hall. Today, low-income youth and parents in families of color are now assuming leadership in developing a unique hybrid approach that integrates community organizing with more traditional child advocacy strategies and focuses on increasing affordable housing and improving the city's educational system. The strategies employed by Coleman have also evolved, shifting from insider advocacy with administrative officials to public campaigns targeting the city budget process, to local initiative campaigns, and most recently to electoral politics. This organizational history features the issues mission and structure, leadership, managing issues, advocacy strategies and community relations, and funding.

Collagens--structure, function, and biosynthesis.

PubMed

Gelse, K; Pöschl, E; Aigner, T

2003-11-28

The extracellular matrix represents a complex alloy of variable members of diverse protein families defining structural integrity and various physiological functions. The most abundant family is the collagens with more than 20 different collagen types identified so far. Collagens are centrally involved in the formation of fibrillar and microfibrillar networks of the extracellular matrix, basement membranes as well as other structures of the extracellular matrix. This review focuses on the distribution and function of various collagen types in different tissues. It introduces their basic structural subunits and points out major steps in the biosynthesis and supramolecular processing of fibrillar collagens as prototypical members of this protein family. A final outlook indicates the importance of different collagen types not only for the understanding of collagen-related diseases, but also as a basis for the therapeutical use of members of this protein family discussed in other chapters of this issue.

Permeating disciplines: Overcoming barriers between molecular simulations and classical structure-function approaches in biological ion transport.

PubMed

Howard, Rebecca J; Carnevale, Vincenzo; Delemotte, Lucie; Hellmich, Ute A; Rothberg, Brad S

2018-04-01

Ion translocation across biological barriers is a fundamental requirement for life. In many cases, controlling this process-for example with neuroactive drugs-demands an understanding of rapid and reversible structural changes in membrane-embedded proteins, including ion channels and transporters. Classical approaches to electrophysiology and structural biology have provided valuable insights into several such proteins over macroscopic, often discontinuous scales of space and time. Integrating these observations into meaningful mechanistic models now relies increasingly on computational methods, particularly molecular dynamics simulations, while surfacing important challenges in data management and conceptual alignment. Here, we seek to provide contemporary context, concrete examples, and a look to the future for bridging disciplinary gaps in biological ion transport. This article is part of a Special Issue entitled: Beyond the Structure-Function Horizon of Membrane Proteins edited by Ute Hellmich, Rupak Doshi and Benjamin McIlwain. Copyright © 2017 Elsevier B.V. All rights reserved.

Proactive and integrated primary care for frail older people: design and methodological challenges of the Utrecht primary care PROactive frailty intervention trial (U-PROFIT).

PubMed

Bleijenberg, Nienke; Drubbel, Irene; Ten Dam, Valerie H; Numans, Mattijs E; Schuurmans, Marieke J; de Wit, Niek J

2012-04-25

Currently, primary care for frail older people is reactive, time consuming and does not meet patients' needs. A transition is needed towards proactive and integrated care, so that daily functioning and a good quality of life can be preserved. To work towards these goals, two interventions were developed to enhance the care of frail older patients in general practice: a screening and monitoring intervention using routine healthcare data (U-PRIM) and a nurse-led multidisciplinary intervention program (U-CARE). The U-PROFIT trial was designed to evaluate the effectiveness of these interventions. The aim of this paper is to describe the U-PROFIT trial design and to discuss methodological issues and challenges. The effectiveness of U-PRIM and U-CARE is being tested in a three-armed, cluster randomized trial in 58 general practices in the Netherlands, with approximately 5000 elderly individuals expected to participate. The primary outcome is the effect on activities of daily living as measured with the Katz ADL index. Secondary outcomes are quality of life, mortality, nursing home admission, emergency department and out-of-hours General Practice (GP), surgery visits, and caregiver burden. In a large, pragmatic trial conducted in daily clinical practice with frail older patients, several challenges and methodological issues will occur. Recruitment and retention of patients and feasibility of the interventions are important issues. To enable broad generalizability of results, careful choices of the design and outcome measures are required. Taking this into account, the U-PROFIT trial aims to provide robust evidence for a structured and integrated approach to provide care for frail older people in primary care. NTR2288.

Integration of micro-/nano-/quantum-scale photonic devices: scientific and technological considerations

NASA Astrophysics Data System (ADS)

Lee, El-Hang; Lee, Seung-Gol; O, Beom Hoan; Park, Se Geun

2004-08-01

Scientific and technological issues and considerations regarding the integration of miniaturized microphotonic devices, circuits and systems in micron, submicron, and quantum scale, are presented. First, we examine the issues regarding the miniaturization of photonic devices including the size effect, proximity effect, energy confinement effect, microcavity effect, optical and quantum interference effect, high field effect, nonlinear effect, noise effect, quantum optical effect, and chaotic effect. Secondly, we examine the issues regarding the interconnection including the optical alignment, minimizing the interconnection losses, and maintaining optical modes. Thirdly, we address the issues regarding the two-dimensional or three-dimensional integration either in a hybrid format or in a monolithic format between active devices and passive devices of varying functions. We find that the concept of optical printed circuit board (O-PCB) that we propose is highly attractive as a platform for micro/nano/quantum-scale photonic integration. We examine the technological issues to be addressed in the process of fabrication, characterization, and packaging for actual implementation of the miniaturization, interconnection and integration. Devices that we have used for our study include: mode conversion schemes, micro-ring and micro-racetrack resonator devices, multimode interference devices, lasers, vertical cavity surface emitting microlasers, and their arrays. Future prospects are also discussed.

"All is well": professionals' documentation of social determinants of health in Swedish Child Health Services health records concerning maltreated children - a mixed method approach.

PubMed

Köhler, Marie; Rosvall, Maria; Emmelin, Maria

2016-08-15

Knowledge about social determinants of health has influenced global health strategies, including early childhood interventions. Some psychosocial circumstances - such as poverty, parental mental health problems, abuse and partner violence - increase the risk of child maltreatment and neglect. Healthcare professionals' awareness of psychosocial issues is of special interest, since they both have the possibility and the obligation to identify vulnerable children. Child Health Services health records of 100 children in Malmö, Sweden, who had been placed in, or were to be placed in family foster care, were compared with health records of a matched comparison group of 100 children who were not placed in care. A mixed-method approach integrating quantitative and qualitative analysis was applied. The documentation about the foster care group was more voluminous than for the comparison group. The content was problem-oriented and dominated by severe parental health and social problems, while the child's own experiences were neglected. The professionals documented interaction with healthcare and social functions, but very few reports to the Social Services were noted. For both groups, notes about social structures were almost absent. Child Health Service professionals facing vulnerable children document parental health issues and interaction with healthcare, but they fail to document living conditions thereby making social structures invisible in the health records. The child perspective is insufficiently integrated in the documentation and serious child protection needs remain unmet, if professionals avoid reporting to Social Services.

Use of microfasteners to produce damage tolerant composite structures

PubMed Central

Hallett, Stephen R.

2016-01-01

The paper concerns the mechanical performance of continuous fibre/thermosetting polymer matrix composites reinforced in the through-thickness direction with fibrous or metallic rods or threads in order to mitigate against low delamination resistance. Specific illustrations of the effects of microfasteners in reducing delamination crack growth are made for Z-pinned and tufted composites. Response to loading in such ‘structured materials’ is subject to multiple parameters defining their in-plane and out-of-plane properties. Single microfastener mechanical tests are well suited to establish the crack bridging laws under a range of loading modes, from simple delamination crack opening to shear, and provide the basis for predicting the corresponding response of microfastener arrays, within a given material environment. The fundamental experiments on microfasteners can be used to derive analytical expressions to describe the crack bridging behaviour in a general sense, to cover all possible loadings. These expressions can be built into cohesive element constitutive laws in a finite-element framework for modelling the effects of microfastener arrays on the out-of-plane mechanical response of reinforced structural elements, including the effects of known manufacturing imperfections. Such predictive behaviour can then be used to assess structural integrity under complex loading, as part of the component design process. This article is part of the themed issue ‘Multiscale modelling of the structural integrity of composite materials’. PMID:27242299

System-on-chip integration of a new electromechanical impedance calculation method for aircraft structure health monitoring.

PubMed

Boukabache, Hamza; Escriba, Christophe; Zedek, Sabeha; Medale, Daniel; Rolet, Sebastien; Fourniols, Jean Yves

2012-10-11

The work reported on this paper describes a new methodology implementation for active structural health monitoring of recent aircraft parts made from carbon-fiber-reinforced polymer. This diagnosis is based on a new embedded method that is capable of measuring the local high frequency impedance spectrum of the structure through the calculation of the electro-mechanical impedance of a piezoelectric patch pasted non-permanently onto its surface. This paper involves both the laboratory based E/M impedance method development, its implementation into a CPU with limited resources as well as a comparison with experimental testing data needed to demonstrate the feasibility of flaw detection on composite materials and answer the question of the method reliability. The different development steps are presented and the integration issues are discussed. Furthermore, we present the unique advantages that the reconfigurable electronics through System-on-Chip (SoC) technology brings to the system scaling and flexibility. At the end of this article, we demonstrate the capability of a basic network of sensors mounted onto a real composite aircraft part specimen to capture its local impedance spectrum signature and to diagnosis different delamination sizes using a comparison with a baseline.

Bipolar disorder: a neural network perspective on a disorder of emotion and motivation.

PubMed

Wessa, Michèle; Kanske, Philipp; Linke, Julia

2014-01-01

Bipolar disorder (BD) is a severe, chronic disease with a heritability of 60-80%. BD is frequently misdiagnosed due to phenomenological overlap with other psychopathologies, an important issue that calls for the identification of biological and psychological vulnerability and disease markers. Altered structural and functional connectivity, mainly between limbic and prefrontal brain areas, have been proposed to underlie emotional and motivational dysregulation in BD and might represent relevant vulnerability and disease markers. In the present laboratory review we discuss functional and structural neuroimaging findings on emotional and motivational dysregulation from our research group in BD patients and healthy individuals at risk to develop BD. As a main result of our studies, we observed altered orbitofrontal and limbic activity and reduced connectivity between dorsal prefrontal and limbic brain regions, as well as reduced integrity of fiber tracts connecting prefrontal and subcortical brain structures in BD patients and high-risk individuals. Our results provide novel insights into pathophysiological mechanisms of bipolar disorder. The current laboratory review provides a specific view of our group on altered brain connectivity and underlying psychological processes in bipolar disorder based on our own work, integrating relevant findings from others. Thereby we attempt to advance neuropsychobiological models of BD.

System-on-Chip Integration of a New Electromechanical Impedance Calculation Method for Aircraft Structure Health Monitoring

PubMed Central

Boukabache, Hamza; Escriba, Christophe; Zedek, Sabeha; Medale, Daniel; Rolet, Sebastien; Fourniols, Jean Yves

2012-01-01

The work reported on this paper describes a new methodology implementation for active structural health monitoring of recent aircraft parts made from carbon-fiber-reinforced polymer. This diagnosis is based on a new embedded method that is capable of measuring the local high frequency impedance spectrum of the structure through the calculation of the electro-mechanical impedance of a piezoelectric patch pasted non-permanently onto its surface. This paper involves both the laboratory based E/M impedance method development, its implementation into a CPU with limited resources as well as a comparison with experimental testing data needed to demonstrate the feasibility of flaw detection on composite materials and answer the question of the method reliability. The different development steps are presented and the integration issues are discussed. Furthermore, we present the unique advantages that the reconfigurable electronics through System-on-Chip (SoC) technology brings to the system scaling and flexibility. At the end of this article, we demonstrate the capability of a basic network of sensors mounted onto a real composite aircraft part specimen to capture its local impedance spectrum signature and to diagnosis different delamination sizes using a comparison with a baseline. PMID:23202013

A cognitive perspective on health systems integration: results of a Canadian Delphi study.

PubMed

Evans, Jenna M; Baker, G Ross; Berta, Whitney; Barnsley, Jan

2014-05-19

Ongoing challenges to healthcare integration point toward the need to move beyond structural and process issues. While we know what needs to be done to achieve integrated care, there is little that informs us as to how. We need to understand how diverse organizations and professionals develop shared knowledge and beliefs - that is, we need to generate knowledge about normative integration. We present a cognitive perspective on integration, based on shared mental model theory, that may enhance our understanding and ability to measure and influence normative integration. The aim of this paper is to validate and improve the Mental Models of Integrated Care (MMIC) Framework, which outlines important knowledge and beliefs whose convergence or divergence across stakeholder groups may influence inter-professional and inter-organizational relations. We used a two-stage web-based modified Delphi process to test the MMIC Framework against expert opinion using a random sample of participants from Canada's National Symposium on Integrated Care. Respondents were asked to rate the framework's clarity, comprehensiveness, usefulness, and importance using seven-point ordinal scales. Spaces for open comments were provided. Descriptive statistics were used to describe the structured responses, while open comments were coded and categorized using thematic analysis. The Kruskall-Wallis test was used to examine cross-group agreement by level of integration experience, current workplace, and current role. In the first round, 90 individuals responded (52% response rate), representing a wide range of professional roles and organization types from across the continuum of care. In the second round, 68 individuals responded (75.6% response rate). The quantitative and qualitative feedback from experts was used to revise the framework. The re-named "Integration Mindsets Framework" consists of a Strategy Mental Model and a Relationships Mental Model, comprising a total of nineteen content areas. The Integration Mindsets Framework draws the attention of researchers and practitioners to how various stakeholders think about and conceptualize integration. A cognitive approach to understanding and measuring normative integration complements dominant cultural approaches and allows for more fine-grained analyses. The framework can be used by managers and leaders to facilitate the interpretation, planning, implementation, management and evaluation of integration initiatives.

Validation of the Community Integration Questionnaire in the adult burn injury population.

PubMed

Gerrard, Paul; Kazis, Lewis E; Ryan, Colleen M; Shie, Vivian L; Holavanahalli, Radha; Lee, Austin; Jette, Alan; Fauerbach, James A; Esselman, Peter; Herndon, David; Schneider, Jeffrey C

2015-11-01

With improved survival, long-term effects of burn injuries on quality of life, particularly community integration, are important outcomes. This study aims to assess the Community Integration Questionnaire's psychometric properties in the adult burn population. Data were obtained from a multicenter longitudinal data set of burn survivors. The psychometric properties of the Community Integration Questionnaire (n = 492) were examined. The questionnaire items were evaluated for clinical and substantive relevance; validation procedures were conducted on different samples of the population; construct validity was assessed using exploratory factor analysis; internal consistency reliability was examined using Cronbach's α statistics; and item response theory was applied to the final models. The CIQ-15 was reduced by two questions to form the CIQ-13, with a two-factor structure, interpreted as self/family care and social integration. Item response theory testing suggests that Factor 2 captures a wider range of community integration levels. Cronbach's α was 0.80 for Factor 1, 0.77 for Factor 2, and 0.79 for the test as a whole. The CIQ-13 demonstrates validity and reliability in the adult burn survivor population addressing issues of self/family care and social integration. This instrument is useful in future research of community reintegration outcomes in the burn population.

Contour integration impairment in schizophrenia and first episode psychosis: state or trait?

PubMed

Feigenson, Keith A; Keane, Brian P; Roché, Matthew W; Silverstein, Steven M

2014-11-01

Contour integration is a fundamental visual process that recovers object structure by representing spatially separated edge elements as a continuous contour or shape boundary. Clinically stable persons with schizophrenia have repeatedly been shown to be impaired at contour integration but it is unclear whether this process varies with clinical state or whether it arises as early as the first episode of psychosis. To consider these issues, we administered a contour integration test to persons with chronic schizophrenia and to those with a first episode of psychosis. The test was administered twice-once at admission to short term psychiatric hospitalization and once again at discharge. A well-matched healthy control group was also tested across the same time points. We found that contour integration performance improved to the same degree in all groups over time, indicating that there were no recovery effects over and above normal practice effects. Moreover, the schizophrenia group demonstrated poorer contour integration than the control group and the first episode group exhibited intermediate performance that could not be distinguished from the other groups. These results suggest that contour integration ability does not vary as a function of short-term changes in clinical state, and that it may become further impaired with an increased number of psychotic episodes. Copyright © 2014 Elsevier B.V. All rights reserved.

The Integrity of Digital Information: Mechanics and Definitional Issues.

ERIC Educational Resources Information Center

Lynch, Clifford A.

1994-01-01

Considers issues regarding the migration of a system of literature into electronic formats. Highlights include integrity in an information distribution system; digest technology; tracings that permit detection of copied digital objects; verifying sources; digital signature technology and cryptography; electronic publishing; and intellectual…

Non-Nuclear Testing of Fission Technologies at NASA MSFC

NASA Technical Reports Server (NTRS)

Houts, Robert G.; Pearson, J. Boise; Aschenbrenner, Kenneth C.; Bradley, David E.; Dickens, Ricky E.; Emrich, William J.; Garber, Anne E.; Godfroy, Thomas J.; Harper, Roger T.; Martin, Jim J.;

Integrating Variable Renewable Energy into the Grid: Key Issues, Greening the Grid (Spanish Version)

DOE Office of Scientific and Technical Information (OSTI.GOV)

This is the Spanish version of 'Greening the Grid - Integrating Variable Renewable Energy into the Grid: Key Issues'. To foster sustainable, low-emission development, many countries are establishing ambitious renewable energy targets for their electricity supply. Because solar and wind tend to be more variable and uncertain than conventional sources, meeting these targets will involve changes to power system planning and operations. Grid integration is the practice of developing efficient ways to deliver variable renewable energy (VRE) to the grid. Good integration methods maximize the cost-effectiveness of incorporating VRE into the power system while maintaining or increasing system stability andmore » reliability. When considering grid integration, policy makers, regulators, and system operators consider a variety of issues, which can be organized into four broad topics: New Renewable Energy Generation, New Transmission, Increased System Flexibility, and Planning for a High RE Future.« less

Achieving development goals for HIV, tuberculosis and malaria in sub-Saharan Africa through integrated antenatal care: barriers and challenges.

PubMed

Fowkes, Freya J I; Draper, Bridget L; Hellard, Margaret; Stoové, Mark

2016-12-12

The global health community is currently transitioning from the Millennium Development Goals (MDGs) to the Sustainable Development Goals (SDGs). Unfortunately, progress towards maternal, newborn and infant health MDGs has lagged significantly behind other key health goals, demanding a renewed global effort in this key health area. The World Health Organization and other institutions heralded integrated antenatal care (ANC) as the best way to address the inter-related health issues of HIV, tuberculosis (TB) and malaria in the high risk groups of pregnant women and infants; integrated ANC services also offer a mechanism to address slow progress towards improved maternal health. There is remarkably limited evidence on best practice approaches of program implementation, acceptability and effectiveness for integrated ANC models targeting multiple diseases. Here, we discuss current integrated ANC global guidelines and the limited literature describing integrated ANC implementation and evidence for their role in addressing HIV, malaria and TB during pregnancy in sub-Saharan Africa. We highlight the paucity of data on the effectiveness of integrated ANC models and identify significant structural barriers in the health system (funding, infrastructure, distribution, human resources), the adoption system (limited buy-in from implementers, leadership, governance) and, in the broader context, patient-centred barriers (fear, stigma, personal burdens) and barriers in funding structures. We highlight recommendations for action and discuss avenues for the global health community to develop systems to integrate multiple disease programs into ANC models of care that better address these three priority infectious diseases. With the current transition to the SDGs and concerns regarding the failure to meet maternal health MDGs, the global health community, researchers, implementers and funding bodies must work together to ensure the establishment of quality operational and implementation research to inform integrated ANC models. It is imperative that the global health community engages in a timely discussion about such implementation innovations and instigates appropriate actions to ensure advances in maternal health are sufficient to meet applicable SDGs.

Autonomous Assembly of Modular Structures in Space and on Extraterrestrial Locations

NASA Technical Reports Server (NTRS)

Alhorn, Dean C.

2005-01-01

The fulfillment of the new US. National Vision for Space Exploration requires many new enabling technologies to accomplish the goal of utilizing space for commercial activities and for returning humans to the moon and extraterrestrial environments. Traditionally, flight structures are manufactured as complete systems and require humans to complete the integration and assembly in orbit. These structures are bulky and require the use of heavy launch vehicles to send the units to the desired location, e.g. International Space Station (ISS). This method requires a high degree of safety, numerous space walks and significant cost for the humans to perform the assembly in orbit. For example, for assembly and maintenance of the ISS, 52 Extravehicular Activities (EVA's) have been performed so far with a total EVA time of approximately 322 hours. Sixteen (16) shuttle flights haw been to the ISS to perform these activities with an approximate cost of $450M per mission. For future space missions, costs have to be reduced to reasonably achieve the exploration goals. One concept that has been proposed is the autonomous assembly of space structures. This concept is an affordable, reliable solution to in-space and extraterrestrial assembly operations. Assembly is autonomously performed when two components containing onboard electronics join after recognizing that the joint is appropriate and in the precise position and orientation required for assembly. The mechanism only activates when the specifications are correct and m a nominal range. After assembly, local sensors and electronics monitor the integrity of the joint for feedback to a master controller. To achieve this concept will require a shift in the methods for designing space structures. In addition, innovative techniques will be required to perform the assembly autonomously. Monitoring of the assembled joint will be necessary for safety and structural integrity. If a very large structure is to be assembled in orbit, then the number of integrity sensors will be significant. Thus simple, low cost sensors are integral to the success of this concept. This paper will address these issues and will propose a novel concept for assembling space structures autonomously. The paper will present Several autonomous assembly methods. Core technologies required to achieve in space assembly will be discussed and novel techniques for communicating, sensing, docking and assembly will be detailed. These core technologies are critical to the goal of utilizing space in a cost efficient and safe manner. Finally, these technologies can also be applied to other systems both on earth and extraterrestrial environments.

VHF Air/Ground Communications for Air Traffic Control: A Decision Tree Approach to System Innovations. Volume 2

DTIC Science & Technology

1993-07-01

GROUND RADIO ISSUES Multiple transmitters and receivers at a common site has been a dfficult integration issue for many communicaton systems...lower data rate vocoders become available. 10. Compatibility of modulation with channel availability and message integrity improvements, including...overrides can use in- frequency and path diversity, integrity improvements band signaling, busy channel overrides, and Frequency diversity and ARQ ARQ is

Warpage Characteristics and Process Development of Through Silicon Via-Less Interconnection Technology.

PubMed

Shen, Wen-Wei; Lin, Yu-Min; Wu, Sheng-Tsai; Lee, Chia-Hsin; Huang, Shin-Yi; Chang, Hsiang-Hung; Chang, Tao-Chih; Chen, Kuan-Neng

2018-08-01

In this study, through silicon via (TSV)-less interconnection using the fan-out wafer-level-packaging (FO-WLP) technology and a novel redistribution layer (RDL)-first wafer level packaging are investigated. Since warpage of molded wafer is a critical issue and needs to be optimized for process integration, the evaluation of the warpage issue on a 12-inch wafer using finite element analysis (FEA) at various parameters is presented. Related parameters include geometric dimension (such as chip size, chip number, chip thickness, and mold thickness), materials' selection and structure optimization. The effect of glass carriers with various coefficients of thermal expansion (CTE) is also discussed. Chips are bonded onto a 12-inch reconstituted wafer, which includes 2 RDL layers, 3 passivation layers, and micro bumps, followed by using epoxy molding compound process. Furthermore, an optical surface inspector is adopted to measure the surface profile and the results are compared with the results from simulation. In order to examine the quality of the TSV-less interconnection structure, electrical measurement is conducted and the respective results are presented.

Slamming: Recent Progress in the Evaluation of Impact Pressures

NASA Astrophysics Data System (ADS)

Dias, Frédéric; Ghidaglia, Jean-Michel

2018-01-01

Slamming, the violent impact between a liquid and solid, has been known to be important for a long time in the ship hydrodynamics community. More recently, applications ranging from the transport of liquefied natural gas (LNG) in LNG carriers to the harvesting of wave energy with oscillating wave surge converters have led to renewed interest in the topic. The main reason for this renewed interest is that the extreme impact pressures generated during slamming can affect the integrity of the structures involved. Slamming fluid mechanics is challenging to describe, as much from an experimental viewpoint as from a numerical viewpoint, because of the large span of spatial and temporal scales involved. Even the physical mechanisms of slamming are challenging: What physical phenomena must be included in slamming models? An important issue deals with the practical modeling of slamming: Are there any simple models available? Are numerical models viable? What are the consequences for the design of structures? This article describes the loading processes involved in slamming, offers state-of-the-art results, and highlights unresolved issues worthy of further research.

241-AW Tank Farm Construction Extent of Condition Review for Tank Integrity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barnes, Travis J.; Gunter, Jason R.; Reeploeg, Gretchen E.

2013-11-19

This report provides the results of an extent of condition construction history review for the 241-AW tank farm. The construction history of the 241-AW tank farm has been reviewed to identify issues similar to those experienced during tank AY-102 construction. Those issues and others impacting integrity are discussed based on information found in available construction records, using tank AY-102 as the comparison benchmark. In the 241-AW tank farm, the fourth double-shell tank farm constructed, similar issues as those with tank 241-AY-102 construction occured. The overall extent of similary and affect on 241-AW tank farm integrity is described herein.

241-AY-101 Tank Construction Extent of Condition Review for Tank Integrity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barnes, Travis J.; Gunter, Jason R.

2013-08-26

This report provides the results of an extent of condition construction history review for tank 241-AY-101. The construction history of tank 241-AY-101 has been reviewed to identify issues similar to those experienced during tank AY-102 construction. Those issues and others impacting integrity are discussed based on information found in available construction records, using tank AY-102 as the comparison benchmark. In tank 241-AY-101, the second double-shell tank constructed, similar issues as those with tank 241-AY-102 construction reoccurred. The overall extent of similary and affect on tank 241-AY-101 integrity is described herein.

Functional Stem Cell Integration into Neural Networks Assessed by Organotypic Slice Cultures.

PubMed

Forsberg, David; Thonabulsombat, Charoensri; Jäderstad, Johan; Jäderstad, Linda Maria; Olivius, Petri; Herlenius, Eric

2017-08-14

Re-formation or preservation of functional, electrically active neural networks has been proffered as one of the goals of stem cell-mediated neural therapeutics. A primary issue for a cell therapy approach is the formation of functional contacts between the implanted cells and the host tissue. Therefore, it is of fundamental interest to establish protocols that allow us to delineate a detailed time course of grafted stem cell survival, migration, differentiation, integration, and functional interaction with the host. One option for in vitro studies is to examine the integration of exogenous stem cells into an existing active neural network in ex vivo organotypic cultures. Organotypic cultures leave the structural integrity essentially intact while still allowing the microenvironment to be carefully controlled. This allows detailed studies over time of cellular responses and cell-cell interactions, which are not readily performed in vivo. This unit describes procedures for using organotypic slice cultures as ex vivo model systems for studying neural stem cell and embryonic stem cell engraftment and communication with CNS host tissue. © 2017 by John Wiley & Sons, Inc. Copyright © 2017 John Wiley & Sons, Inc.

Integrative Analysis of Longitudinal Metabolomics Data from a Personal Multi-Omics Profile

PubMed Central

Stanberry, Larissa; Mias, George I.; Haynes, Winston; Higdon, Roger; Snyder, Michael; Kolker, Eugene

2013-01-01

The integrative personal omics profile (iPOP) is a pioneering study that combines genomics, transcriptomics, proteomics, metabolomics and autoantibody profiles from a single individual over a 14-month period. The observation period includes two episodes of viral infection: a human rhinovirus and a respiratory syncytial virus. The profile studies give an informative snapshot into the biological functioning of an organism. We hypothesize that pathway expression levels are associated with disease status. To test this hypothesis, we use biological pathways to integrate metabolomics and proteomics iPOP data. The approach computes the pathways’ differential expression levels at each time point, while taking into account the pathway structure and the longitudinal design. The resulting pathway levels show strong association with the disease status. Further, we identify temporal patterns in metabolite expression levels. The changes in metabolite expression levels also appear to be consistent with the disease status. The results of the integrative analysis suggest that changes in biological pathways may be used to predict and monitor the disease. The iPOP experimental design, data acquisition and analysis issues are discussed within the broader context of personal profiling. PMID:24958148

The Vehicle Integrated Performance Analysis Experience: Reconnecting With Technical Integration

NASA Technical Reports Server (NTRS)

McGhee, D. S.

2006-01-01

Very early in the Space Launch Initiative program, a small team of engineers at MSFC proposed a process for performing system-level assessments of a launch vehicle. Aimed primarily at providing insight and making NASA a smart buyer, the Vehicle Integrated Performance Analysis (VIPA) team was created. The difference between the VIPA effort and previous integration attempts is that VIPA a process using experienced people from various disciplines, which focuses them on a technically integrated assessment. The foundations of VIPA s process are described. The VIPA team also recognized the need to target early detailed analysis toward identifying significant systems issues. This process is driven by the T-model for technical integration. VIPA s approach to performing system-level technical integration is discussed in detail. The VIPA process significantly enhances the development and monitoring of realizable project requirements. VIPA s assessment validates the concept s stated performance, identifies significant issues either with the concept or the requirements, and then reintegrates these issues to determine impacts. This process is discussed along with a description of how it may be integrated into a program s insight and review process. The VIPA process has gained favor with both engineering and project organizations for being responsive and insightful

Overview of the ACT program

NASA Technical Reports Server (NTRS)

Davis, John G., Jr.

1992-01-01

NASA's Advanced Composites Program (ACT) was initiated in 1988. A National Research Announcement was issued to solicit innovative ideas that could significantly contribute to development and demonstration of an integrated technology data base and confidence level that permits cost-effective use of composite primary structures in transport aircraft. Fifteen contracts were awarded by the Spring of 1989 and the participants include commercial and military airframe manufacturers, materials developers and suppliers, universities, and government laboratories. The program approach is to develop materials, structural mechanics methodology, design concepts, and fabrication procedures that offer the potential to make composite structures cost-effective compared to aluminum structure. Goals for the ACT program included 30-50 percent weight reduction, 20-25 percent acquisition cost reduction, and provided the scientific basis for predicting materials and structures performance. This paper provides an overview of the ACT program status, plans, and selected technical accomplishments. Sixteen additional papers, which provide more detailed information on the research and development accomplishments, are contained in this publication.

Multi-Sensor Documentation of Metric and Qualitative Information of Historic Stone Structures

NASA Astrophysics Data System (ADS)

Adamopoulos, E.; Tsilimantou, E.; Keramidas, V.; Apostolopoulou, M.; Karoglou, M.; Tapinaki, S.; Ioannidis, C.; Georgopoulos, A.; Moropoulou, A.

2017-08-01

This paper focuses on the integration of multi-sensor techniques regarding the acquisition, processing, visualisation and management of data regarding historic stone structures. The interdisciplinary methodology that is carried out here comprises of two parts. In the first part, the acquisition of qualitative and quantitative data concerning the geometry, the materials and the degradation of the tangible heritage asset each time, is discussed. The second part, refers to the analysis, management and visualization of the interrelated data by using spatial information technologies. Through the paradigm of the surveying of the ancient temple of Pythian Apollo at Acropolis of Rhodes, Rhodes Island, Greece, it is aimed to highlight the issues deriving from the separate application of documentation procedures and how the fusion of these methods can contribute effectively to ensure the completeness of the measurements for complex structures. The surveying results are further processed to be compatible and integrated with GIS. Also, the geometric documentation derivatives are combined with environmental data and the results of the application of non-destructive testing and evaluation techniques in situ and analytical techniques in lab after sampling. GIS operations are utilized to document the building materials but also to model and to analyse the decay extent and patterns. Detailed surface measurements and geo-processing analysis are executed. This integrated approach, helps the assessment of past interventions on the monument, identify main causes of damage and decay, and finally assist the decision making on the most compatible materials and techniques for protection and restoration works.

Applying radio-frequency identification (RFID) technology in transfusion medicine.

PubMed

Hohberger, Clive; Davis, Rodeina; Briggs, Lynne; Gutierrez, Alfonso; Veeramani, Dhamaraj

2012-05-01

ISO/IEC 18000-3 mode 1 standard 13.56 MHz RFID tags have been accepted by the International Society for Blood Transfusion (ISBT) and the United States Food and Drug Administration (FDA) as data carriers to integrate with and augment ISBT 128 barcode data carried on blood products. The use of 13.56 MHz RFID carrying ISBT 128 data structures allows the global deployment and use of RFID, supporting both international transfer of blood and international disaster relief. The deployment in process at the BloodCenter of Wisconsin and testing at the University of Iowa Health Center is the first FDA-permitted implementation of RFID throughout in all phases of blood banking, donation through transfusion. RFID technology and equipment selection will be discussed along with FDA-required RF safety testing; integration with the blood enterprise computing system and required RFID tag performance. Tag design and survivability is an issue due to blood bag centrifugation and irradiation. Deployment issues will be discussed. Use of RFID results in significant return on investment over the use of barcodes in the blood center operations through labor savings and error reduction. Copyright © 2011 The International Alliance for Biological Standardization. Published by Elsevier Ltd. All rights reserved.

Real-time simulation of contact and cutting of heterogeneous soft-tissues.

PubMed

Courtecuisse, Hadrien; Allard, Jérémie; Kerfriden, Pierre; Bordas, Stéphane P A; Cotin, Stéphane; Duriez, Christian

2014-02-01

This paper presents a numerical method for interactive (real-time) simulations, which considerably improves the accuracy of the response of heterogeneous soft-tissue models undergoing contact, cutting and other topological changes. We provide an integrated methodology able to deal both with the ill-conditioning issues associated with material heterogeneities, contact boundary conditions which are one of the main sources of inaccuracies, and cutting which is one of the most challenging issues in interactive simulations. Our approach is based on an implicit time integration of a non-linear finite element model. To enable real-time computations, we propose a new preconditioning technique, based on an asynchronous update at low frequency. The preconditioner is not only used to improve the computation of the deformation of the tissues, but also to simulate the contact response of homogeneous and heterogeneous bodies with the same accuracy. We also address the problem of cutting the heterogeneous structures and propose a method to update the preconditioner according to the topological modifications. Finally, we apply our approach to three challenging demonstrators: (i) a simulation of cataract surgery (ii) a simulation of laparoscopic hepatectomy (iii) a brain tumor surgery. Copyright © 2013 Elsevier B.V. All rights reserved.

Return-to-work intervention during cancer treatment - The providers' experiences.

PubMed

Petersen, K S; Momsen, A H; Stapelfeldt, C M; Olsen, P R; Nielsen, C V

2018-03-01

To explore in-depth understanding of providers' experiences when involved in a return-to-work (RTW) intervention offered during cancer treatment. Semi-structured individual interviews and participant observations at a hospital department and two municipal job centers were carried out, including ten providers (physicians, nurses and social workers). A phenomenological-hermeneutic approach was applied, involving coding, identification of themes and interpretation of findings. Three major themes were identified: Treatment first, Work as an integrated component in cancer rehabilitation, and Challenges in bringing up work issues. Differences in providers' experiences of the RTW intervention offered to cancer patients were found: in the hospital setting RTW was a second priority, whereas in the municipality job centers it was an integrated component. Further studies are needed to investigate how and when occupational rehabilitation services can be implemented across sectors to support cancer patients' RTW. In the future, work issues ought to be systematically presented by providers across sectors as early as possible to support cancer patients' RTW. Cancer patients' individual needs and thoughts about RTW are to be identified by both health care providers during treatment and social workers at the municipality level and shared across sectors. © 2017 John Wiley & Sons Ltd.

Micromachined Fluid Inertial Sensors

PubMed Central

Liu, Shiqiang; Zhu, Rong

2017-01-01

Micromachined fluid inertial sensors are an important class of inertial sensors, which mainly includes thermal accelerometers and fluid gyroscopes, which have now been developed since the end of the last century for about 20 years. Compared with conventional silicon or quartz inertial sensors, the fluid inertial sensors use a fluid instead of a solid proof mass as the moving and sensitive element, and thus offer advantages of simple structures, low cost, high shock resistance, and large measurement ranges while the sensitivity and bandwidth are not competitive. Many studies and various designs have been reported in the past two decades. This review firstly introduces the working principles of fluid inertial sensors, followed by the relevant research developments. The micromachined thermal accelerometers based on thermal convection have developed maturely and become commercialized. However, the micromachined fluid gyroscopes, which are based on jet flow or thermal flow, are less mature. The key issues and technologies of the thermal accelerometers, mainly including bandwidth, temperature compensation, monolithic integration of tri-axis accelerometers and strategies for high production yields are also summarized and discussed. For the micromachined fluid gyroscopes, improving integration and sensitivity, reducing thermal errors and cross coupling errors are the issues of most concern. PMID:28216569

Teaching Research Integrity and Bioethics to Science Undergraduates

ERIC Educational Resources Information Center

Turrens, Julio F.

2005-01-01

Undergraduate students in the Department of Biomedical Sciences at the University of South Alabama, Mobile, are required to take a course entitled "Issues in Biomedical Sciences," designed to increase students' awareness about bioethical questions and issues concerning research integrity. This paper describes the main features of this…

Dynamic Mobility Applications Policy Analysis: Policy and Institutional Issues for Integrated Dynamic Transit Operations (IDTO). [supporting datasets

DOT National Transportation Integrated Search

2015-01-27

The datasets in this zip file are in support of Intelligent Transportation Systems Joint Program Office (ITS JPO) report FHWA-JPO-14-134, "Dynamic Mobility Applications Policy Analysis: Policy and Institutional Issues for Integrated Dynamic Transit O...

Lifelong Bilingualism Contributes to Cognitive Reserve against White Matter Integrity Declines in Aging

PubMed Central

Gold, Brian T.; Johnson, Nathan F.; Powell, David K.

2013-01-01

Recent evidence suggests that lifelong bilingualism may contribute to cognitive reserve (CR) in normal aging. However, there is currently no neuroimaging evidence to suggest that lifelong bilinguals can retain normal cognitive functioning in the face of age-related neurodegeneration. Here we explored this issue by comparing white matter (WM) integrity and gray matter (GM) volumetric patterns of older adult lifelong bilinguals (N = 20) and monolinguals (N = 20). The groups were matched on a range of relevant cognitive test scores and on the established CR variables of education, socioeconomic status and intelligence. Participants underwent high-resolution structural imaging for assessment of GM volume and diffusion tensor imaging (DTI) for assessment of WM integrity. Results indicated significantly lower microstructural integrity in the bilingual group in several WM tracts. In particular, compared to their monolingual peers, the bilingual group showed lower fractional anisotropy and/or higher radial diffusivity in the inferior longitudinal fasciculus/inferior fronto-occipital fasciculus bilaterally, the fornix, and multiple portions of the corpus callosum. There were no group differences in GM volume. Our results suggest that lifelong bilingualism contributes to CR against WM integrity declines in aging. PMID:24103400

The Multicultural Identity Integration Scale (MULTIIS): Developing a comprehensive measure for configuring one's multiple cultural identities within the self.

PubMed

Yampolsky, Maya A; Amiot, Catherine E; de la Sablonnière, Roxane

2016-04-01

The research investigating how one's multiple cultural identities are configured within the self has yet to account for existing cultural identity configurations aside from integration, and for identifying with more than 2 cultural groups at once. The current research addresses these issues by constructing the Multicultural Identity Integration Scale (MULTIIS) to examine 3 different multicultural identity configurations, and their relationship to well-being based on Amiot and colleagues' (2007) cognitive-developmental model of social identity integration (CDSMII). Diverse samples of multicultural individuals completed the MULTIIS along with identity and well-being measures. (Study 1A: N = 407; 1B: N = 310; 2A = 338 and 2A = 254) RESULTS: Reliability and confirmatory factorial analyses (Studies 1A and 2A) all supported the factorial structure of the MULTIIS. Regression analyses (Studies 1B and 2B) confirmed that the integration subscale of the MULTIIS positively predicted well-being, whereas compartmentalization negatively predicted well-being. Categorization was inconsistently related to well-being. These findings support the CDSMII and the usefulness of the MULTIIS measure, and suggest that each identity configuration is uniquely related to well-being outcomes. (c) 2016 APA, all rights reserved).

Prediction of tautomer ratios by embedded-cluster integral equation theory

NASA Astrophysics Data System (ADS)

Kast, Stefan M.; Heil, Jochen; Güssregen, Stefan; Schmidt, K. Friedemann

2010-04-01

The "embedded cluster reference interaction site model" (EC-RISM) approach combines statistical-mechanical integral equation theory and quantum-chemical calculations for predicting thermodynamic data for chemical reactions in solution. The electronic structure of the solute is determined self-consistently with the structure of the solvent that is described by 3D RISM integral equation theory. The continuous solvent-site distribution is mapped onto a set of discrete background charges ("embedded cluster") that represent an additional contribution to the molecular Hamiltonian. The EC-RISM analysis of the SAMPL2 challenge set of tautomers proceeds in three stages. Firstly, the group of compounds for which quantitative experimental free energy data was provided was taken to determine appropriate levels of quantum-chemical theory for geometry optimization and free energy prediction. Secondly, the resulting workflow was applied to the full set, allowing for chemical interpretations of the results. Thirdly, disclosure of experimental data for parts of the compounds facilitated a detailed analysis of methodical issues and suggestions for future improvements of the model. Without specifically adjusting parameters, the EC-RISM model yields the smallest value of the root mean square error for the first set (0.6 kcal mol-1) as well as for the full set of quantitative reaction data (2.0 kcal mol-1) among the SAMPL2 participants.

Optical printed circuit board (O-PCB) and VLSI photonic integrated circuits: visions, challenges, and progresses

NASA Astrophysics Data System (ADS)

Lee, El-Hang; Lee, S. G.; O, B. H.; Park, S. G.; Noh, H. S.; Kim, K. H.; Song, S. H.

2006-09-01

A collective overview and review is presented on the original work conducted on the theory, design, fabrication, and in-tegration of micro/nano-scale optical wires and photonic devices for applications in a newly-conceived photonic systems called "optical printed circuit board" (O-PCBs) and "VLSI photonic integrated circuits" (VLSI-PIC). These are aimed for compact, high-speed, multi-functional, intelligent, light-weight, low-energy and environmentally friendly, low-cost, and high-volume applications to complement or surpass the capabilities of electrical PCBs (E-PCBs) and/or VLSI electronic integrated circuit (VLSI-IC) systems. These consist of 2-dimensional or 3-dimensional planar arrays of micro/nano-optical wires and circuits to perform the functions of all-optical sensing, storing, transporting, processing, switching, routing and distributing optical signals on flat modular boards or substrates. The integrated optical devices include micro/nano-scale waveguides, lasers, detectors, switches, sensors, directional couplers, multi-mode interference devices, ring-resonators, photonic crystal devices, plasmonic devices, and quantum devices, made of polymer, silicon and other semiconductor materials. For VLSI photonic integration, photonic crystals and plasmonic structures have been used. Scientific and technological issues concerning the processes of miniaturization, interconnection and integration of these systems as applicable to board-to-board, chip-to-chip, and intra-chip integration, are discussed along with applications for future computers, telecommunications, and sensor-systems. Visions and challenges toward these goals are also discussed.

Report of the Asilomar 3 LDR Workshop

NASA Technical Reports Server (NTRS)

Mahoney, M. J. (Editor)

1988-01-01

The conclusions and recommendations of the workshop held to study technology development issues critical to the Large Deployable Reflector (LDR) are summarized. LDR is to be a dedicated, orbiting, astronomical observatory, operating at wavelengths from 30 to 1000 microns, a spectral region where the Earth's atmosphere is almost completely opaque. Because it will have a large, segmented, passively cooled aperture, LDR addresses a wide range of technology areas. These include lightweight, low cost, structural composite reflector panels, primary support structures, wavefront sensing and adaptive optics, thermal background management, and integrated vibration and pointing control systems. The science objectives for LDR present instrument development challenges for coherent and direct arrayed detectors which can operate effectively at far infrared and submillimeter wavelengths, and for sub-Kelvin cryogenic systems.

The structural neural substrate of subjective happiness

PubMed Central

Sato, Wataru; Kochiyama, Takanori; Uono, Shota; Kubota, Yasutaka; Sawada, Reiko; Yoshimura, Sayaka; Toichi, Motomi

2015-01-01

Happiness is a subjective experience that is an ultimate goal for humans. Psychological studies have shown that subjective happiness can be measured reliably and consists of emotional and cognitive components. However, the neural substrates of subjective happiness remain unclear. To investigate this issue, we used structural magnetic resonance imaging and questionnaires that assessed subjective happiness, the intensity of positive and negative emotional experiences, and purpose in life. We found a positive relationship between the subjective happiness score and gray matter volume in the right precuneus. Moreover, the same region showed an association with the combined positive and negative emotional intensity and purpose in life scores. Our findings suggest that the precuneus mediates subjective happiness by integrating the emotional and cognitive components of happiness. PMID:26586449

The structural neural substrate of subjective happiness.

PubMed

Sato, Wataru; Kochiyama, Takanori; Uono, Shota; Kubota, Yasutaka; Sawada, Reiko; Yoshimura, Sayaka; Toichi, Motomi

2015-11-20

Happiness is a subjective experience that is an ultimate goal for humans. Psychological studies have shown that subjective happiness can be measured reliably and consists of emotional and cognitive components. However, the neural substrates of subjective happiness remain unclear. To investigate this issue, we used structural magnetic resonance imaging and questionnaires that assessed subjective happiness, the intensity of positive and negative emotional experiences, and purpose in life. We found a positive relationship between the subjective happiness score and gray matter volume in the right precuneus. Moreover, the same region showed an association with the combined positive and negative emotional intensity and purpose in life scores. Our findings suggest that the precuneus mediates subjective happiness by integrating the emotional and cognitive components of happiness.

APPLICATION OF THE 3D MODEL OF RAILWAY VIADUCTS TO COST ESTIMATION AND CONSTRUCTION

NASA Astrophysics Data System (ADS)

Fujisawa, Yasuo; Yabuki, Nobuyoshi; Igarashi, Zenichi; Yoshino, Hiroyuki

Three dimensional models of civil engineering structures are only partially used in either design or construction but not both. Research on integration of design, cost estimation and construction by 3Dmodels has not been heard in civil engineering domain yet. Using continuously a 3D product model of a structure from design to construction through estimation should improve the efficiency and decrease the occurrence of mistakes, hence enhancing the quality. In this research, we investigated the current practices of flow from design to construction, particularly focusing on cost estimation. Then, we identified advantages and issues on utilization of 3D design models to estimation and construction by applying 3D models to an actual railway construction project.

The Ecology of Seamounts: Structure, Function, and Human Impacts

NASA Astrophysics Data System (ADS)

Clark, Malcolm R.; Rowden, Ashley A.; Schlacher, Thomas; Williams, Alan; Consalvey, Mireille; Stocks, Karen I.; Rogers, Alex D.; O'Hara, Timothy D.; White, Martin; Shank, Timothy M.; Hall-Spencer, Jason M.

2010-01-01

In this review of seamount ecology, we address a number of key scientific issues concerning the structure and function of benthic communities, human impacts, and seamount management and conservation. We consider whether community composition and diversity differ between seamounts and continental slopes, how important dispersal capabilities are in seamount connectivity, what environmental factors drive species composition and diversity, whether seamounts are centers of enhanced biological productivity, and whether they have unique trophic architecture. We discuss how vulnerable seamount communities are to fishing and mining, and how we can balance exploitation of resources and conservation of habitat. Despite considerable advances in recent years, there remain many questions about seamount ecosystems that need closer integration of molecular, oceanographic, and ecological research.

Functional Generalized Structured Component Analysis.

PubMed

Suk, Hye Won; Hwang, Heungsun

2016-12-01

An extension of Generalized Structured Component Analysis (GSCA), called Functional GSCA, is proposed to analyze functional data that are considered to arise from an underlying smooth curve varying over time or other continua. GSCA has been geared for the analysis of multivariate data. Accordingly, it cannot deal with functional data that often involve different measurement occasions across participants and a large number of measurement occasions that exceed the number of participants. Functional GSCA addresses these issues by integrating GSCA with spline basis function expansions that represent infinite-dimensional curves onto a finite-dimensional space. For parameter estimation, functional GSCA minimizes a penalized least squares criterion by using an alternating penalized least squares estimation algorithm. The usefulness of functional GSCA is illustrated with gait data.

The role of nurse specialists in the delivery of integrated diabetes care: a cross-sectional survey of diabetes nurse specialist services.

PubMed

Riordan, Fiona; McHugh, Sheena M; Murphy, Katie; Barrett, Julie; Kearney, Patricia M

2017-08-11

International evidence suggests the diabetes nurse specialist (DNS) has a key role in supporting integrated management of diabetes. We examine whether hospital and community DNS currently support the integration of care, examine regional variation in aspects of the service relevant to the delivery of integrated care and identify barriers to service delivery and areas for improvement. A cross-sectional survey of hospital and community-based DNS in Ireland. Between September 2015 and April 2016, a 67-item online survey, comprising closed and open questions on their clinical role, diabetes clinics, multidisciplinary working, and barriers and facilitators to service delivery, was administered to all eligible DNS (n=152) in Ireland. DNS were excluded if they were retired or on maternity leave or extended leave. The response rate was 66.4% (n=101): 60.6% (n=74) and 89.3% (n=25) among hospital and community DNS, respectively. Most DNS had patients with stable (81.8%) and complicated type 2 diabetes mellitus (89.9%) attending their service. The majority were delivering nurse-led clinics (81.1%). Almost all DNS had a role liaising with (91%), and providing support and education to (95%), other professionals. However, only a third reported that there was local agreement on how their service should operate between the hospital and primary care. Barriers to service delivery that were experienced by DNS included deficits in the availability of specialist staff (allied health professionals, endocrinologists and DNS), insufficient space for clinics, structured education and issues with integration. Delivering integrated diabetes care through a nurse specialist-led approach requires that wider service issues, including regional disparities in access to specialist resources and formalising agreements and protocols on multidisciplinary working between settings, be explicitly addressed. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Integration of Environmental Issues in a Physics Course: 'Physics by Inquiry' High School Teachers' Integration Models and Challenges

NASA Astrophysics Data System (ADS)

Kimori, David Abiya

As we approach the second quarter of the twenty-first century, one may predict that the environment will be among the dominant themes in the political and educational discourse. Over the past three decades, particular perspectives regarding the environment have begun to emerge: (i) realization by human beings that we not only live on earth and use its resources at an increasingly high rate but we also actually belong to the earth and the total ecology of all living systems, (ii) there are strong interactions among different components of the large and complex systems that make up our environment, and (iii) the rising human population and its impact on the environment is a great concern (Hughes & Mason, 2014). Studies have revealed that although the students do not have a deep understanding of environmental issues and lack environmental awareness and attitudes necessary for protecting the environment, they have great concern for the environment (Chapman & Sharma, 2001; Fien, Yencken, & Sykes, 2002). However, addressing environmental issues in the classroom and other disciplines has never been an easy job for teachers (Pennock & Bardwell, 1994; Edelson, 2007). Using multiple case studies, this study investigated how three purposefully selected physics teachers teaching a 'Physics by Inquiry' course integrated environmental topics and issues in their classroom. Particularly this study looked at what integration models and practices the three physics teachers employed in integrating environmental topics and issues in their classroom and what challenges the teachers faced while integrating environmental topics in their classrooms. Data collection methods including field notes taken from observations, teachers' interviews and a collection of artifacts and documents were used. The data were coded analyzed and organized into codes and categories guided by Fogarty (1991) models of curriculum integration and Ham and Sewing (1988) four categories of barriers to environmental education. Findings of this study indicate that teachers acknowledge the importance of teaching environmental issues in their classrooms but continue to struggle with conceptual, educational, logistical and attitudinal barriers to successful integration of environmental topics in physics.

EDITORIAL: Adaptive and Active Materials: Selected Papers from the ASME 2008 Conference on Smart Materials, Adaptive Structures and Intelligent Systems (SMASIS 08) (Maryland, USA, 28-30 October 2008) Adaptive and Active Materials: Selected Papers from the ASME 2008 Conference on Smart Materials, Adaptive Structures and Intelligent Systems (SMASIS 08) (Maryland, USA, 28-30 October 2008)

NASA Astrophysics Data System (ADS)

Lynch, Christopher

2009-10-01

The rapid development of the field of Smart Materials, Adaptive Structures, and Materials Systems led the Aerospace Division ASMS TC to launch the new annual SMASIS conference in 2008. The conference focuses on the multi-disciplinary challenges of developing new multifunctional materials and implementing them in advanced systems. The research spans length scales from nano-structured materials to civil, air, and space structures. The first conference consisted of six symposia, each focusing on a different research area. This special issue of Smart Materials and Structures summarizes some of the top research presented at the 2008 SMASIS conference in the materials-focused symposia. These symposia focused on the behavior and mechanics of active materials, on multifunctional materials, and on bio-inspired materials. The behavior and mechanics of active materials is an approach that combines observed material behavior with mechanism-based models that not only give insight into the observed behavior, but guide the development of new materials. This approach has been applied to shape memory metals and polymers, ferroelectrics, ferromagnetics, and recently to multiferroic materials, and has led to considerable improvements in our understanding of multi-field phenomena. Multifunctional materials are the next generation of active materials. These materials include structural, sensing, and actuation components integrated into a material system. A natural extension of multifunctional materials is a new class of bio-inspired materials. Bio-inspired materials range from detailed bio-mimicry of sensing and self healing materials to nano and microstructures that take advantage of features observed in biological systems. The Editors would like to express their sincere thanks to all of the authors for their contributions to this special issue on 'Adaptive and Active Materials' for Smart Materials and Structures. We convey our gratitude to all of the reviewers for their time and dedication. We thank IOP Publishing for their support and encouragement of this special issue and the staff for their special attention and timely response.

Chinese Localisation of Evergreen: An Open Source Integrated Library System

ERIC Educational Resources Information Center

Zou, Qing; Liu, Guoying

2009-01-01

Purpose: The purpose of this paper is to investigate various issues related to Chinese language localisation in Evergreen, an open source integrated library system (ILS). Design/methodology/approach: A Simplified Chinese version of Evergreen was implemented and tested and various issues such as encoding, indexing, searching, and sorting…

Identity Development Process and Content: Toward an Integrated and Contextualized Science of Identity

ERIC Educational Resources Information Center

Galliher, Renee V.; Rivas-Drake, Deborah; Dubow, Eric F.

2017-01-01

This introductory summary provides an overview of the content of the special issue entitled "Identity Development Process and Content: Toward an Integrated and Contextualized Science of Identity." The 16 theoretical and empirical articles that comprise this special issue were selected to highlight innovative methodologies, theoretical…

Vertically Integrating Professional Skills throughout a Mathematics Major

ERIC Educational Resources Information Center

Dziak, Clarice; Leventhal, Brian; Luttman, Aaron; Skufca, Joseph

2014-01-01

In response to a university mandate to include "professional issues" as a component of every major, we have developed a vertically integrated approach to incorporating the study of professional skills and issues into the mathematics curriculum. Beginning in the first year of study, mathematics majors take an inquiry-based course in…

IDRA Newsletter. Volume 44, No. 4

ERIC Educational Resources Information Center

Goodman, Christie L., Ed.

2017-01-01

Each edition of the IDRA Newsletter strives to provide many different perspectives on the issues in education topics discussed and to define its significance in the state and national dialogue. This issue focuses on School Integration and includes: (1) Using Socioeconomic Indicators as a Tool for School Diversity and Integration (David Hinojosa…

At Issue: Academic Integrity, an Annotated Bibliography

ERIC Educational Resources Information Center

Pricer, Wayne F.

2009-01-01

Academic integrity is central to the heart of any academic institution, yet the topic is a complex one. This bibliography addresses the subjects of copyright and plagiarism. Resources for exploring common campus copyright and fair use issues seek to answer common, frequently misunderstood questions such as what exactly does "copyright" mean? What…

Integrating Augmented Reality Technology to Enhance Children's Learning in Marine Education

ERIC Educational Resources Information Center

Lu, Su-Ju; Liu, Ying-Chieh

2015-01-01

Marine education comprises rich and multifaceted issues. Raising general awareness of marine environments and issues demands the development of new learning materials. This study adapts concepts from digital game-based learning to design an innovative marine learning program integrating augmented reality (AR) technology for lower grade primary…

Cultural Competency Training for Public Health Students: Integrating Self, Social, and Global Awareness Into a Master of Public Health Curriculum

PubMed Central

Delva, Marlyn; Franks, Cheryl L.; Jimenez-Bautista, Ana; Moon-Howard, Joyce; Glover, Jim; Begg, Melissa D.

2015-01-01

Cultural competency training in public health, medicine, social work, nursing, dental medicine, and other health professions has been a topic of increasing interest and significance. Despite the now burgeoning literature that describes specific knowledge, attitudes, and skills that promote cultural “competence,” fully defining this complex, multidimensional term and implementing activities to enhance it remain a challenge. We describe our experiences in introducing a mandatory, full-day workshop to incoming Master of Public Health students, called “Self, Social, and Global Awareness: Personal Capacity Building for Professional Education and Practice.” The purpose of the program is to provide a meaningful, structured environment to explore issues of culture, power, privilege, and social justice, emphasizing the centrality of these issues in effective public health education and practice. PMID:25706008

The implementation of psychiatric advance directives: experiences from a Dutch crisis card initiative.

PubMed

van der Ham, Alida J; Voskes, Yolande; van Kempen, Nel; Broerse, Jacqueline E W; Widdershoven, Guy A M

2013-06-01

The crisis card is a specific form of psychiatric advance directive, documenting mental clients' treatment preferences in advance of a potential psychiatric crisis. In this paper, we aim to provide insight into implementation issues surrounding the crisis card. A Dutch crisis-card project formed the scope of this study. Data were collected through interviews with 15 participants from six stakeholder groups. Identified implementation issues are: (a) The role of the crisis-card counselor, (b) lack of distribution and familiarity, (c) care professionals' routines, and (d) client readiness. The crisis-card counselor appears to play a key role in fostering benefits of the crisis card by supporting clients' perspectives. More structural integration of the crisis card in care processes may enhance its impact, but should be carefully explored. (PsycINFO Database Record (c) 2013 APA, all rights reserved).

Ethical Considerations in HIV/AIDS Biobehavioral Surveys That Use Respondent-Driven Sampling: Illustrations From Lebanon

PubMed Central

DeJong, Jocelyn; Mahfoud, Ziyad; Khoury, Danielle; Barbir, Farah

2009-01-01

Respondent-driven sampling is especially useful for reaching hidden populations and is increasingly used internationally in public health research, particularly on HIV. Respondent-driven sampling involves peer recruitment and has a dual-incentive structure: both recruiters and their peer recruits are paid. Recent literature focusing on the ethical dimensions of this method in the US context has identified integral safeguards that protect against ethical violations. We analyzed a study of 3 groups in Lebanon who are at risk for HIV (injection drug users, men who have sex with men, female sex workers) and the ethical issues that arose. More explicit attention should be given to ethical issues involved in research implementing respondent-driven sampling of at-risk populations in developing countries, where ethical review mechanisms may be weak. PMID:19608961

Conceptualizing the cross-cultural gaps in managing international aid: HIV/AIDS and TB project delivery in Southern Africa.

PubMed

Jackson, Terence

2011-01-01

There appears to be a gap between the billions of dollars inputted into fighting HIV/AIDS and TB and outcomes. This in part can be attributed to the lack of attention in International Development to managing programmes and projects within complex levels of cross-cultural interactions. International Development often ignores management issues, yet Management Studies is left wanting through a lack of engagement with development issues including the fight against disease and poverty. This paper attempts to link these two disciplines towards mutual benefit, through a critical cross-cultural approach. It provides contextualization of international development policies/strategies; conceptualization of dominant paradigms; structural analysis of how a programme/project fits into the global governance structure; analysis of complexities and levels of cross-cultural interaction and their consequences and the process and implications of knowledge transfer across cultural distances. It concludes with implications for policy and practice, as well as what is needed from cross-disciplinary research. This includes how feedback loops can be strengthened from local to global, how indigenous knowledge may be better understood and integrated, how power relations within the global governance structure could be managed, how cross-cultural interaction could be better understood, and how knowledge transfer/sharing should be critically managed. Copyright © 2010 John Wiley & Sons, Ltd.

Plant roots: understanding structure and function in an ocean of complexity

PubMed Central

Ryan, Peter R.; Delhaize, Emmanuel; Watt, Michelle; Richardson, Alan E.

2016-01-01

Background The structure and function of plant roots and their interactions with soil are exciting scientific frontiers that will ultimately reveal much about our natural systems, global water and mineral and carbon cycles, and help secure food supplies into the future. This Special Issue presents a collection of papers that address topics at the forefront of our understanding of root biology. Scope These papers investigate how roots cope with drought, nutrient deficiencies, toxicities and soil compaction as well as the interactions that roots have with soil microorganisms. Roots of model plant species, annual crops and perennial species are studied in short-term experiments through to multi-year trials. Spatial scales range from the gene up to farming systems and nutrient cycling. The diverse, integrated approaches described by these studies encompass root genetics as applied to soil management, as well as documenting the signalling processes occurring between roots and shoots and between roots and soil. Conclusions This Special Issue on roots presents invited reviews and research papers covering a span of topics ranging from fundamental aspects of anatomy, growth and water uptake to roots in crop and pasture systems. Understanding root structure and function and adaptation to the abiotic and biotic stresses encountered in field conditions is important for sustainable agricultural production and better management of natural systems.

GaAs MOEMS Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

SPAHN, OLGA B.; GROSSETETE, GRANT D.; CICH, MICHAEL J.

2003-03-01

Many MEMS-based components require optical monitoring techniques using optoelectronic devices for converting mechanical position information into useful electronic signals. While the constituent piece-parts of such hybrid opto-MEMS components can be separately optimized, the resulting component performance, size, ruggedness and cost are substantially compromised due to assembly and packaging limitations. GaAs MOEMS offers the possibility of monolithically integrating high-performance optoelectronics with simple mechanical structures built in very low-stress epitaxial layers with a resulting component performance determined only by GaAs microfabrication technology limitations. GaAs MOEMS implicitly integrates the capability for radiation-hardened optical communications into the MEMS sensor or actuator component, a vitalmore » step towards rugged integrated autonomous microsystems that sense, act, and communicate. This project establishes a new foundational technology that monolithically combines GaAs optoelectronics with simple mechanics. Critical process issues addressed include selectivity, electrochemical characteristics, and anisotropy of the release chemistry, and post-release drying and coating processes. Several types of devices incorporating this novel technology are demonstrated.« less

Integrating cost information with health management support system: an enhanced methodology to assess health care quality drivers.

PubMed

Kohli, R; Tan, J K; Piontek, F A; Ziege, D E; Groot, H

1999-08-01

Changes in health care delivery, reimbursement schemes, and organizational structure have required health organizations to manage the costs of providing patient care while maintaining high levels of clinical and patient satisfaction outcomes. Today, cost information, clinical outcomes, and patient satisfaction results must become more fully integrated if strategic competitiveness and benefits are to be realized in health management decision making, especially in multi-entity organizational settings. Unfortunately, traditional administrative and financial systems are not well equipped to cater to such information needs. This article presents a framework for the acquisition, generation, analysis, and reporting of cost information with clinical outcomes and patient satisfaction in the context of evolving health management and decision-support system technology. More specifically, the article focuses on an enhanced costing methodology for determining and producing improved, integrated cost-outcomes information. Implementation issues and areas for future research in cost-information management and decision-support domains are also discussed.

Decision support for green supply chain operations by integrating dynamic simulation and LCA indicators: diaper case study.

PubMed

Adhitya, Arief; Halim, Iskandar; Srinivasan, Rajagopalan

2011-12-01

As the issue of environmental sustainability is becoming an important business factor, companies are now looking for decision support tools to assess the fuller picture of the environmental impacts associated with their manufacturing operations and supply chain (SC) activities. Lifecycle assessment (LCA) is widely used to measure the environmental consequences assignable to a product. However, it is usually limited to a high-level snapshot of the environmental implications over the product value chain without consideration of the dynamics arising from the multitiered structure and the interactions along the SC. This paper proposes a framework for green supply chain management by integrating a SC dynamic simulation and LCA indicators to evaluate both the economic and environmental impacts of various SC decisions such as inventories, distribution network configuration, and ordering policy. The advantages of this framework are demonstrated through an industrially motivated case study involving diaper production. Three distinct scenarios are evaluated to highlight how the proposed approach enables integrated decision support for green SC design and operation.

Towards integrating extracellular matrix and immunological pathways.

PubMed

Boyd, David F; Thomas, Paul G

2017-10-01

The extracellular matrix (ECM) is a complex and dynamic structure made up of an estimated 300 different proteins. The ECM is also a rich source of cytokines and growth factors in addition to numerous bioactive ECM degradation products that influence cell migration, proliferation, and differentiation. The ECM is constantly being remodeled during homeostasis and in a wide range of pathological contexts. Changes in the ECM modulate immune responses, which in turn regulate repair and regeneration of tissues. Here, we review the many components of the ECM, enzymes involved in ECM remodeling, and the signals that feed into immunological pathways in the context of a dynamic ECM. We highlight studies that have taken an integrative approach to studying immune responses in the context of the ECM and studies that use novel proteomic strategies. Finally, we discuss research challenges relevant to the integration of immune and ECM networks and propose experimental and translational approaches to resolve these issues. Copyright © 2017 Elsevier Ltd. All rights reserved.

Barriers and facilitators to integrating care: experiences from the English Integrated Care Pilots

PubMed Central

Ling, Tom; Brereton, Laura; Conklin, Annalijn; Newbould, Jennifer; Roland, Martin

2012-01-01

Background: In 2008, the English Department of Health appointed 16 ‘Integrated Care Pilots’ which used a range of approaches to provide better integrated care. We report qualitative analyses from a three-year multi-method evaluation to identify barriers and facilitators to successful integration of care. Theory and methods: Data were analysed from transcripts of 213 in-depth staff interviews, and from semi-structured questionnaires (the ‘Living Document’) completed by staff in pilot sites at six points over a two-year period. Emerging findings were therefore built from ‘bottom up’ and grounded in the data. However, we were then interested in how these findings compared and contrasted with more generic analyses. Therefore after our analyses were complete we then systematically compared and contrasted the findings with the analysis of barriers and facilitators to quality improvement identified in a systematic review by Kaplan et al. (2010) and the analysis of more micro-level shapers of behaviour found in Normalisation Process Theory (May et al. 2007). Neither of these approaches claims to be full blown theories but both claim to provide mid-range theoretical arguments which may be used to structure existing data and which can be undercut or reinforced by new data. Results and discussion: Many barriers and facilitators to integrating care are those of any large-scale organisational change. These include issues relating to leadership, organisational culture, information technology, physician involvement, and availability of resources. However, activities which appear particularly important for delivering integrated care include personal relationships between leaders in different organisations, the scale of planned activities, governance and finance arrangements, support for staff in new roles, and organisational and staff stability. We illustrate our analyses with a ‘routemap’ which identifies questions that providers may wish to consider when planning interventions to improve the integration of care. PMID:23593044

Fatigue behavior and life prediction of a SiC/Ti-24Al-11Nb composite under isothermal conditions. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Bartolotta, Paul A.

1991-01-01

Metal Matrix Composites (MMC) and Intermetallic Matrix Composites (IMC) were identified as potential material candidates for advanced aerospace applications. They are especially attractive for high temperature applications which require a low density material that maintains its structural integrity at elevated temperatures. High temperature fatigue resistance plays an important role in determining the structural integrity of the material. This study attempts to examine the relevance of test techniques, failure criterion, and life prediction as they pertain to an IMC material, specifically, unidirectional SiC fiber reinforced titanium aluminide. A series of strain and load controlled fatigue tests were conducted on unidirectional SiC/Ti-24Al-11Nb composite at 425 and 815 C. Several damage mechanism regimes were identified by using a strain-based representation of the data, Talreja's fatigue life diagram concept. Results of these tests were then used to address issues of test control modes, definition of failure, and testing techniques. Finally, a strain-based life prediction method was proposed for an IMC under tensile cyclic loadings at elevated temperatures.

Evaluation of grid generation technologies from an applied perspective

NASA Technical Reports Server (NTRS)

Hufford, Gary S.; Harrand, Vincent J.; Patel, Bhavin C.; Mitchell, Curtis R.

1995-01-01

An analysis of the grid generation process from the point of view of an applied CFD engineer is given. Issues addressed include geometric modeling, structured grid generation, unstructured grid generation, hybrid grid generation and use of virtual parts libraries in large parametric analysis projects. The analysis is geared towards comparing the effective turn around time for specific grid generation and CFD projects. The conclusion was made that a single grid generation methodology is not universally suited for all CFD applications due to both limitations in grid generation and flow solver technology. A new geometric modeling and grid generation tool, CFD-GEOM, is introduced to effectively integrate the geometric modeling process to the various grid generation methodologies including structured, unstructured, and hybrid procedures. The full integration of the geometric modeling and grid generation allows implementation of extremely efficient updating procedures, a necessary requirement for large parametric analysis projects. The concept of using virtual parts libraries in conjunction with hybrid grids for large parametric analysis projects is also introduced to improve the efficiency of the applied CFD engineer.

Vertically Emitting Indium Phosphide Nanowire Lasers.

PubMed

Xu, Wei-Zong; Ren, Fang-Fang; Jevtics, Dimitars; Hurtado, Antonio; Li, Li; Gao, Qian; Ye, Jiandong; Wang, Fan; Guilhabert, Benoit; Fu, Lan; Lu, Hai; Zhang, Rong; Tan, Hark Hoe; Dawson, Martin D; Jagadish, Chennupati

2018-06-13

Semiconductor nanowire (NW) lasers have attracted considerable research effort given their excellent promise for nanoscale photonic sources. However, NW lasers currently exhibit poor directionality and high threshold gain, issues critically limiting their prospects for on-chip light sources with extremely reduced footprint and efficient power consumption. Here, we propose a new design and experimentally demonstrate a vertically emitting indium phosphide (InP) NW laser structure showing high emission directionality and reduced energy requirements for operation. The structure of the laser combines an InP NW integrated in a cat's eye (CE) antenna. Thanks to the antenna guidance with broken asymmetry, strong focusing ability, and high Q-factor, the designed InP CE-NW lasers exhibit a higher degree of polarization, narrower emission angle, enhanced internal quantum efficiency, and reduced lasing threshold. Hence, this NW laser-antenna system provides a very promising approach toward the achievement of high-performance nanoscale lasers, with excellent prospects for use as highly localized light sources in present and future integrated nanophotonics systems for applications in advanced sensing, high-resolution imaging, and quantum communications.

Application of controller partitioning optimization procedure to integrated flight/propulsion control design for a STOVL aircraft

NASA Technical Reports Server (NTRS)

Garg, Sanjay; Schmidt, Phillip H.

1993-01-01

A parameter optimization framework has earlier been developed to solve the problem of partitioning a centralized controller into a decentralized, hierarchical structure suitable for integrated flight/propulsion control implementation. This paper presents results from the application of the controller partitioning optimization procedure to IFPC design for a Short Take-Off and Vertical Landing (STOVL) aircraft in transition flight. The controller partitioning problem and the parameter optimization algorithm are briefly described. Insight is provided into choosing various 'user' selected parameters in the optimization cost function such that the resulting optimized subcontrollers will meet the characteristics of the centralized controller that are crucial to achieving the desired closed-loop performance and robustness, while maintaining the desired subcontroller structure constraints that are crucial for IFPC implementation. The optimization procedure is shown to improve upon the initial partitioned subcontrollers and lead to performance comparable to that achieved with the centralized controller. This application also provides insight into the issues that should be addressed at the centralized control design level in order to obtain implementable partitioned subcontrollers.

Design of an x-ray telescope optics for XEUS

NASA Astrophysics Data System (ADS)

Graue, Roland; Kampf, Dirk; Wallace, Kotska; Lumb, David; Bavdaz, Marcos; Freyberg, Michael

2017-11-01

The X-ray telescope concept for XEUS is based on an innovative high performance and light weight Silicon Pore Optics technology. The XEUS telescope is segmented into 16 radial, thermostable petals providing the rigid optical bench structure of the stand alone XRay High Precision Tandem Optics. A fully representative Form Fit Function (FFF) Model of one petal is currently under development to demonstrate the outstanding lightweight telescope capabilities with high optically effective area. Starting from the envisaged system performance the related tolerance budgets were derived. These petals are made from ceramics, i.e. CeSiC. The structural and thermal performance of the petal shall be reported. The stepwise alignment and integration procedure on petal level shall be described. The functional performance and environmental test verification plan of the Form Fit Function Model and the test set ups are described in this paper. In parallel to the running development activities the programmatic and technical issues wrt. the FM telescope MAIT with currently 1488 Tandem Optics are under investigation. Remote controlled robot supported assembly, simultaneous active alignment and verification testing and decentralised time effective integration procedures shall be illustrated.

Practice Innovation for Care Integration, Opioid Management, and Quality Measurement in Family Medicine.

PubMed

Neale, Anne Victoria; Bowman, Marjorie A; Seehusen, Dean A

Ringing in the new year 2017! This may finally be the year of real practice improvement after many false starts. Research into practice transformation has informed both local work and national policy. Human factors and payment structures are key. And payment structures depend on how quality is measured. Large gaps between practicing physician recommendations for the most important quality measures and those currently imposed externally are exposed in this issue. Also see information on in-practice social work consultations and their outcomes and recommendations from innovators in integrated care, and for chronic opioid therapy management based on visits to many family medicine offices. Visit entropy is negative for hospital readmissions. Another article reaffirms the importance of family physicians in rural obstetrics, including Cesarean deliveries. Two articles address changing Latino health care access. New Mexico's innovative health extension agent implementation now includes research in ways that benefit all. And a glass half-full: the growth in the diversity of family medicine faculty is above average, but is not occurring as quickly as in the general population. © Copyright 2017 by the American Board of Family Medicine.

A review of utility issues for the integration of wind electric generators

NASA Technical Reports Server (NTRS)

Reddoch, T. W.; Barnes, P. R.

1982-01-01

A review of issues and concerns of the electric utility industry for the integration of wind electric generation is offered. The issues have been categorized in three major areas: planning, operations, and dynamic interaction. Representative studies have been chosen for each area to illustrate problems and to alleviate some concerns. The emphasis of this paper is on individual large wind turbines (WTs) and WT arrays for deployment at the bulk level in a utility system.

Treatment Issues for Aboriginal Mothers with Substance Use Problems and Their Children

PubMed Central

Niccols, Allison; Dell, Colleen Anne; Clarke, Sharon

2014-01-01

In many cultures, approximately one third of people with drug dependence are women of child-bearing age. Substance use among pregnant and parenting women is a major public health concern. Aboriginal people have some of the highest rates of substance abuse in Canada, increasing concern for detrimental health impacts, including those for women and their children. For many women, substance abuse offers a means of coping with trauma, such as childhood abuse, partner violence, and, for Aboriginal women, the intergenerational effects of colonization. In this paper, we review treatment issues for Aboriginal mothers with substance use problems and their children. We discuss gender-specific issues in substance abuse, the need for women-specific treatment, the impact of substance abuse on children and parenting, the additional risks for Aboriginal women and children, and the need for integrated programs (those that integrate pregnancy-, parenting-, and child-related services with women-specific addiction treatment). We describe New Choices as an example of an integrated program, review research on existing treatment for Aboriginal mothers with substance use issues, and describe Sheway as a promising integrated program for Aboriginal women with substance abuse issues and their young children. There are few treatment programs specifically for Aboriginal mothers with substance use issues and their children and very little research on their effectiveness. Based on our review of existing evidence, we offer recommendations for future research and practice. PMID:24976814

Membership and management: structures of inter-professional working in community mental health teams for older people in England.

PubMed

Wilberforce, Mark; Tucker, Sue; Abendstern, Michele; Brand, Christian; Giebel, Clarissa Marie; Challis, David

2013-09-01

Community mental health services are regarded as the preferred first tier of specialist psychogeriatric support, with integrated multidisciplinary teams believed to offer improved decision-making and greater continuity of care than separate single-profession services. In England over 400 community mental health teams (CMHTs) form the cornerstone of such support, yet research has neither assessed progress toward integrating key professional disciplines nor the nature of their membership and management arrangements. A self-administered questionnaire was sent to all CMHTs for older people in England, seeking a combination of objective and subjective information on team structure and management. Responses from 376 (88%) teams highlighted broader multidisciplinary membership than found in a 2004 survey, with particular growth in the number of support workers and other unqualified practitioners. Only modest progress was found in the integration of psychologists and social workers within CMHTs. The data also revealed a trend toward "core" team membership, and away from "sessional" membership in which staff may have divided loyalties between services. Multidisciplinary working was reported as beneficial by many respondents, but examples of "silo working" were also found, which may have hampered service delivery in a minority of teams. The reported growth in the number of practitioners without professional registration raises issues about the appropriate skill mix and substitution within CMHTs, while local agencies should review barriers to the integration of psychologists and social workers. Further research is required to explore the quality of multidisciplinary team working.

EDITORIAL: Integrated non-invasive sensing techniques and geophysical methods for the study and conservation of architectural, archaeological and artistic heritage Integrated non-invasive sensing techniques and geophysical methods for the study and conservation of architectural, archaeological and artistic heritage

NASA Astrophysics Data System (ADS)

Masini, N.; Soldovieri, F.

2011-09-01

In the last two decades, the use of non-invasive methods for the study and conservation of cultural heritage, from artefacts and historical sites to recent architectural structures, has gained increasing interest. This is due to several reasons: (i) the improvement of performance and information resolution of sensors and devices; (ii) the increasing availability of user-friendly data/image analysis, and processing software and routines; (iii) the ever greater awareness of archaeologists and conservators of the benefits of these technologies, in terms of reduction of costs, time and the risk associated with direct and destructive investigations of archaeological sites (excavation) and monuments (i.e. masonry coring). The choice of diagnostic strategy depends on the spatial and physical characteristics of the cultural objects or sites, the aim of the investigation (knowledge, conservation, restoration) and the issues to be addressed (monitoring, decay assessment, etc). This makes the set up and validation of ad hoc procedures based on data processing and post-processing methods necessary, generally developed to address issues in other fields of application. This methodological perspective based on an integrated and multi-scale approach characterizes the papers of this special issue, which is focused on integrated non-invasive sensing techniques and geophysical methods for the study and conservation of architectural, archaeological and artistic heritage. In particular, attention is given to the advanced application of the synthetic aperture radar (SAR) from the satellite-based platform for deformation monitoring thanks to the innovative differential SAR interferometry (DInSAR) technique; Zeni et al show the significant possibilities of the proposed methodology in achieving a global vision not only of cultural heritage but also of the embedding territory. This collection also deals with the application of non-invasive diagnostics to archaeological prospecting, and cultural heritage monitoring and diagnostics. The paper by Conyers et al gives a very good review of the limitations and advantages of ground penetrating radar (GPR) in archaeological prospecting, where the focus is on aspects of data processing and image visualization. Kadioglu et al describe a case that exploits GPR to define buried archaeological remains at the Zeynel Bey Tomb in the ancient city of Hasankeyf, Turkey. In particular, attention is given to a new three-dimensional visualization of the scene which provides a clearer representation compared to the usual constant depth slices. The paper by Bavusi et al is concerned with the use of GPR as a tool to monitor an important recent architectural masterpiece and critical piece of infrastructure, the Musmeci bridge in Potenza; in particular, the complexity of this civil engineering structure is tackled by adopting advanced data processing tools such as microwave tomography. A microwave tomographic approach is also exploited for GPR data processing in cultural heritage diagnostics by Brancaccio et al, where their survey is concerned with the masonry diagnostics at St Carmine's Church, one of the more ancient and important monuments of Naples. This special issue also gives a good overview of state-of-the-art methodologies and appealing cases of data integration and correlation. Nordebo et al present a new and advanced approach to information fusion, used here to combine ERT data from different orientations. The approach is general, suitable for sensor integration, and opens up a new route to data fusion for diagnostics and monitoring. Some very interesting cases of data integration in archaeological prospecting and cultural heritage monitoring are also presented. Loperte et al present an interesting case of an integrated geophysical approach based on magnetic, GPR and geoelectric techniques used to investigate the Greek and Roman settlement of Paestum in southern Italy; their aim is to undertake preventive archaeological research on an area of the ancient settlement affected by new construction. Another interesting case of on-field integration of GPR and seismic techniques is presented by Leucci et al; their aim is to characterize the deterioration status of the pillars of the cathedral of Tricarico, in the Basilicata region of southern Italy, where the diagnostics have provided crucial information that is helping to drive the restoration work. Another example of sensor integration is presented by Carlomagno et al, which is focused on the joint exploitation of infrared thermography and GPR for inspection of architectonic structures. Two important studies are presented: the first aims to evaluate the conservation of frescoes as well as the state of the underground masonry structure at Pompei (Naples); the second aims to evaluate the state of degradation of remnants of a theatre at a site in Nora (Cagliari). The integration of different diagnostic techniques is shown to be important also for movable pieces such as the sculpture of the Pharaoh with the god Amun, one of the most important pieces in the 'Museo delle Antichitá Egizie' of Turin. In particular, Sambuelli et al demonstrate the joint use of GPR ultrasonic 2D tomographies to assess the integrity of the base of the statue. Capizzi et al propose the integration of a pacometer, high frequency GPR and ultrasonic techniques to investigate the internal extension of all the visible fractures (and to search for hidden ones) of a marble slab (second to third century AD) from the archaeological museum of Rome, which was damaged in transit for an exhibition. Finally, this special issue also presents cases of surface and material characterization, which is a field of increasing interest in monumental heritage monitoring. Camaiti et al present a survey that uses a portable hyperspectral device to characterize the alteration affecting the marble facade of the Santa Maria Novella church (13th century) in Florence. Their analysis shows how hyperspectral instruments may be considered a powerful tool for characterizing historical surfaces in a non-destructive and non-invasive way. Fort et al describe an advanced petrophysical analysis of several types of natural stone used in Spain that can be used to determine their anisotropy, which is one of the key factors affecting the quality and resistance to decay caused by a variety of different agents, such as water.

MO-A-BRB-03: Integration Issues in Electronic Charting for External Beam Therapy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sutlief, S.

2015-06-15

The process of converting to an electronic chart for radiation therapy can be daunting. It requires a dedicated committee to first research and choose appropriate software, to review the entire documentation policy and flow of the clinic, to convert this system to electronic form or if necessary, redesign the system to more easily conform to the electronic process. Those making the conversion and those who already use electronic charting would benefit from the shared experience of those who have been through the process in the past. Therefore TG262 was convened to provide guidance on electronic charting for external beam radiationmore » therapy and brachytherapy. This course will present the results of an internal survey of task group members on EMR practices in External Beam Radiation Therapy as well as discuss important issues in EMR development and structure for both EBRT and brachytherapy. Learning Objectives: Be familiarized with common practices and pitfalls in development and maintenance of an electronic chart in Radiation Oncology Be familiarized with important issues related to electronic charting in External Beam Radiation Therapy Be familiarized with important issues related to electronic charting in Brachytherapy.« less

Professional development for university scientists around issues of equity and diversity: Investigating dissent within community

NASA Astrophysics Data System (ADS)

Bianchini, Julie A.; Hilton-Brown, Bryan A.; Breton, Therese D.

2002-10-01

We investigated the role of dissent in a community of university scientists, engineers, mathematicians, and social scientists engaged in a 2-year professional development project around issues of equity and diversity. Members of this teacher learning community explored issues related to gender and ethnicity in science education, and attempted to develop course materials and instructional strategies inclusive of students from underrepresented groups. We focused our attention on those professional development sessions (6 of the 19) devoted to a contentious yet integral topic in science education: the gendered and multicultural nature of science. We examined conversations initiated by a member's concerns to learn how dissent led (or failed to lead) to new insights into feminist science studies scholarship or to greater understanding of ways to address equity issues in undergraduate science education. We also explored how teacher learners' resulting views of feminist science studies scholarship informed (or failed to inform) changes in their own educational practices. From our qualitative analyses, we highlight the challenges in balancing respect for members' individual voices with collective progress toward project goals, and in structuring conversations initiated by dissent to provide adequate space for deliberation and movement toward deeper understanding of equity and excellence.

The hierarchical structure of DSM-5 pathological personality traits.

PubMed

Wright, Aidan G C; Thomas, Katherine M; Hopwood, Christopher J; Markon, Kristian E; Pincus, Aaron L; Krueger, Robert F

2012-11-01

A multidimensional trait system has been proposed for representing personality disorder (PD) features in the fifth edition of the Diagnostic and Statistical Manual of Mental Disorders (DSM-5) to address problematic classification issues such as comorbidity. In this model, which may also assist in providing scaffolding for the underlying structure of major forms of psychopathology more generally, 25 primary traits are organized by 5 higher order dimensions: Negative Affect, Detachment, Antagonism, Disinhibition, and Psychoticism. We examined (a) the generalizability of the structure proposed for DSM-5 PD traits, and (b) the potential for an integrative hierarchy based upon DSM-5 PD traits to represent the dimensions scaffolding psychopathology more generally. A large sample of student participants (N = 2,461) completed the Personality Inventory for DSM-5, which operationalizes the DSM-5 traits. Exploratory factor analysis replicated the initially reported 5-factor structure, as indicated by high factor congruencies. The 2-, 3-, and 4-factor solutions estimated in the hierarchy of the DSM-5 traits bear close resemblance to existing models of common mental disorders, temperament, and personality pathology. Thus, beyond the description of individual differences in personality disorder, the trait dimensions might provide a framework for the metastructure of psychopathology in the DSM-5 and the integration of a number of ostensibly competing models of personality trait covariation. (PsycINFO Database Record (c) 2012 APA, all rights reserved).

How to integrate quantitative information into imaging reports for oncologic patients.

PubMed

Martí-Bonmatí, L; Ruiz-Martínez, E; Ten, A; Alberich-Bayarri, A

2018-05-01

Nowadays, the images and information generated in imaging tests, as well as the reports that are issued, are digital and represent a reliable source of data. Reports can be classified according to their content and to the type of information they include into three main types: organized (free text in natural language), predefined (with templates and guidelines elaborated with previously determined natural language like that used in BI-RADS and PI-RADS), or structured (with drop-down menus displaying questions with various possible answers that have been agreed on with the rest of the multidisciplinary team, which use standardized lexicons and are structured in the form of a database with data that can be traced and exploited with statistical tools and data mining). The structured report, compatible with Management of Radiology Report Templates (MRRT), makes it possible to incorporate quantitative information related with the digital analysis of the data from the acquired images to accurately and precisely describe the properties and behavior of tissues by means of radiomics (characteristics and parameters). In conclusion, structured digital information (images, text, measurements, radiomic features, and imaging biomarkers) should be integrated into computerized reports so that they can be indexed in large repositories. Radiologic databanks are fundamental for exploiting health information, phenotyping lesions and diseases, and extracting conclusions in personalized medicine. Copyright © 2018 SERAM. Publicado por Elsevier España, S.L.U. All rights reserved.

Cell wall integrity, genotoxic injury and PCD dynamics in alfalfa saponin-treated white poplar cells highlight a complex link between molecule structure and activity.

PubMed

Paparella, Stefania; Tava, Aldo; Avato, Pinarosa; Biazzi, Elisa; Macovei, Anca; Biggiogera, Marco; Carbonera, Daniela; Balestrazzi, Alma

2015-03-01

In the present work, eleven saponins and three sapogenins purified from Medicago sativa were tested for their cytotoxicity against highly proliferating white poplar (Populus alba L.) cell suspension cultures. After preliminary screening, four saponins with different structural features in terms of aglycone moieties and sugar chains (saponin 3, a bidesmoside of hederagenin; saponins 4 and 5, monodesmoside and bidesmoside of medicagenic acid respectively, and saponin 10, a bidesmoside of zanhic acid) and different cytotoxicity were selected and used for further investigation on their structure-activity relationship. Transmission Electron Microscopy (TEM) analyses provided for the first time evidence of the effects exerted by saponins on plant cell wall integrity. Exposure to saponin 3 and saponin 10 resulted into disorganization of the outer wall layer and the effect was even more pronounced in white poplar cells treated with the two medicagenic acid derivatives, saponins 4 and 5. Oxidative burst and nitric oxide accumulation were common hallmarks of the response of white poplar cells to saponins. When DNA damage accumulation and DNA repair profiles were evaluated by Single Cell Gel Electrophoresis, induction of single and double strand breaks followed by effective repair was observed within 24h. The reported data are discussed in view of the current issues dealing with saponin structure-activity relationship. Copyright © 2015 Elsevier Ltd. All rights reserved.

MODFLOW-OWHM v2: New Features and Improvements; The Next Generation of MODFLOW Conjunctive Use Simulation

NASA Astrophysics Data System (ADS)

Boyce, S. E.; Hanson, R. T.; Henson, W.; Ferguson, I. M.; Schmid, W.; Reimann, T.; Mehl, S.

2017-12-01

The One-Water Hydrologic Flow Model (One-Water) is a MODFLOW-based integrated hydrologic flow model designed for the analysis of a broad range of conjunctive-use and sustainability issues. It was motivated by the need to merge the multiple variants of MODFLOW-2005 to yield an enhanced unified version capable of simulating conjunctive use and management, sustainability, climate-related issues, and managing the relationships between groundwater, surface water, and land usage. One-Water links the movement and use of groundwater, surface water, and imported water for consumption by agriculture and natural vegetation on the landscape, and for potable and other uses within a supply-and-demand framework. The first version, released in 2014, was selected by The World Bank Water Resource Software Review in 2016 as one of three recommended simulation programs for conjunctive use and management modeling. One-Water is also being used as the primary simulation engine for FREEWAT, a European Union sponsored open-source water management software environment. The next version of One-Water will include a new surface-water operations module that simulates dynamic reservoir operations and a conduit-flow process for karst aquifers and leaky pipe networks. It will also include enhancements to local grid refinement, and additional features to facilitate easier model updates, faster execution, better error messages, and more integration/cross communication between the traditional MODFLOW packages. The new structure also helps facilitate the new integration into a "Self-Updating" structure of data streams, simulation, and analysis needed for modern water resource management. By retaining and tracking the water within the hydrosphere, One-Water accounts for "all of the water everywhere and all of the time." This philosophy provides more confidence in the water accounting to the scientific community and provides the public a foundation needed to address wider classes of problems. Ultimately, more complex questions are being asked about water resources, requiring tools that more completely answer conjunctive-use management questions.

β-Boomerang Antimicrobial and Antiendotoxic Peptides: Lipidation and Disulfide Bond Effects on Activity and Structure.

PubMed

Mohanram, Harini; Bhattacharjya, Surajit

2014-04-21

Drug-resistant Gram-negative bacterial pathogens and endotoxin- or lipopolysaccharide (LPS)-mediated inflammations are among some of the most  prominent health issues globally. Antimicrobial peptides (AMPs) are eminent molecules that can kill drug-resistant strains and neutralize LPS toxicity. LPS, the outer layer of the outer membrane of Gram-negative bacteria safeguards cell integrity against hydrophobic compounds, including antibiotics and AMPs. Apart from maintaining structural integrity, LPS, when released into the blood stream, also induces inflammatory pathways leading to septic shock. In previous works, we have reported the de novo design of a set of 12-amino acid long cationic/hydrophobic peptides for LPS binding and activity. These peptides adopt β-boomerang like conformations in complex with LPS. Structure-activity studies demonstrated some critical features of the β-boomerang scaffold that may be utilized for the further development of potent analogs. In this work, β-boomerang lipopeptides were designed and structure-activity correlation studies were carried out. These lipopeptides were homo-dimerized through a disulfide bridge to stabilize conformations and for improved activity. The designed peptides exhibited potent antibacterial activity and efficiently neutralized LPS toxicity under in vitro assays. NMR structure of C4YI13C in aqueous solution demonstrated the conserved folding of the lipopeptide with a boomerang aromatic lock stabilized with disulfide bond at the C-terminus and acylation at the N-terminus. These lipo-peptides displaying bacterial sterilization and low hemolytic activity may be useful for future applications as antimicrobial and antiendotoxin molecules.

Creating an infrastructure for training in the responsible conduct of research: the University of Pittsburgh's experience.

PubMed

Barnes, Barbara E; Friedman, Charles P; Rosenberg, Jerome L; Russell, Joanne; Beedle, Ari; Levine, Arthur S

2006-02-01

In response to public concerns about the consequences of research misconduct, academic institutions have become increasingly cognizant of the need to implement comprehensive, effective training in the responsible conduct of research (RCR) for faculty, staff, students, and external collaborators. The ability to meet this imperative is challenging as universities confront declining financial resources and increasing complexity of the research enterprise. The authors describe the University of Pittsburgh's design, implementation, and evaluation of a Web-based, institution-wide RCR training program called Research and Practice Fundamentals (RPF). This project, established in 2000, was embedded in the philosophy, organizational structure, and technology developed through the Integrated Advanced Information Management Systems grant from the National Library of Medicine. Utilizing a centralized, comprehensive approach, the RPF system provides an efficient mechanism for deploying content to a large, diverse cohort of learners and supports the needs of research administrators by providing access to information about who has successfully completed the training. During its first 3 years of operation, the RPF served over 17,000 users and issued more than 38,000 training certificates. The 18 modules that are currently available address issues required by regulatory mandates and other content areas important to the research community. RPF users report high levels of satisfaction with content and ease of using the system. Future efforts must explore methods to integrate non-RCR education and training into a centralized, cohesive structure. The University of Pittsburgh's experience with the RPF demonstrates the importance of developing an infrastructure for training that is comprehensive, scalable, reliable, centralized, affordable, and sustainable.

"Drop-In" Biofuels Solve Integration Issues? - Continuum Magazine | NREL

Science.gov Websites

NREL's ReFUEL Lab. Photo by Dennis Schroeder, NREL "Drop-In" Biofuels Solve Integration Issues by Dennis Schroeder, NREL The National Advanced Biofuels Consortium (NABC), which NREL and Pacific . Photo by Dennis Schroeder, NREL The second process the NABC is investigating is the catalytic conversion

Primary Prevention Programs at the Elementary Level: Issues of Treatment Integrity, Systematic Screening, and Reinforcement

ERIC Educational Resources Information Center

Lane, Kathleen Lynne; Kalberg, Jemma Robertson; Bruhn, Allison Leigh; Mahoney, Michelle E.; Driscoll, Steven A.

2008-01-01

This study examined issues of treatment integrity, systematic screenings, and access to reinforcement relative to school-wide positive behavior support programs (SW-PBS) implemented in two rural elementary schools during the first year of program implementation. Results suggested that treatment fidelity, as measured by self-report and direct…

Technology in Education: Technology Integration into the School's Curriculum

ERIC Educational Resources Information Center

Culver, Bobby L., Jr.

2017-01-01

Integrating technology into the school's curriculum is a very contentious issue. However, it is an important issue that schools need to consider and assess. The purpose of this study was to examine the relationship between K-5th grade teachers' perceptions of proficiency of technology equipment, experience with technology in education, and…

Integration of Work Experience and Learning for International Students: From Harmony to Inequality

ERIC Educational Resources Information Center

Tran, Ly Thi; Soejatminah, Sri

2017-01-01

The integration of work experience and learning in tertiary education is a complex issue for different stakeholders, including students, institutions, and employers. The provision of course-related work experience for international students is far more challenging as it involves issues of visa status, different cultural expectations,…

Integrating Socio-Scientific Issues to Enhance the Bioethical Decision-Making Skills of High School Students

ERIC Educational Resources Information Center

Gutierez, Sally B.

2015-01-01

Scientific literacy has been focused on the construction of students' knowledge to use appropriate and meaningful concepts, critically think, and make balanced, well-informed decisions relevant to their lives. This study presents the effects of integrating socio-scientific issues to enhance the bioethical decision-making skills of biology…

Teaching Research Integrity and Bioethics to Science Undergraduates

PubMed Central

2005-01-01

Undergraduate students in the Department of Biomedical Sciences at the University of South Alabama, Mobile, are required to take a course entitled “Issues in Biomedical Sciences,” designed to increase students' awareness about bioethical questions and issues concerning research integrity. This paper describes the main features of this course and summarizes the results of a survey designed to evaluate the students' perceptions about the course. A summary of this study was presented at the 2002 Conference on Research Integrity in Potomac, MD, sponsored by the Office of Research Integrity of the National Institutes of Health. PMID:16341260

Tunable Microwave Components for Ku- and K-Band Satellite Communications

NASA Technical Reports Server (NTRS)

Miranada, F. A.; VanKeuls, F. W.; Romanofsky, R. R.; Subramanyam, G.

1998-01-01

The use of conductor/ferroelectric/dielectric thin film multilayer structures for frequency and phase agile components at frequencies at and above the Ku-band will be discussed. Among these components are edge coupled filters, microstripline ring resonators, and phase shifters. These structures were implemented using SrTiO3 (STO) ferroelectric thin films, with gold or YBa2Cu3O7-d (YBCO) high temperature superconducting (HTS) microstrip fines deposited by laser ablation on LaAlO3 (LAO) substrates. The performance of these structures in terms of tunability, operating temperature, frequency, and dc bias will be presented. Because of their small size, light weight, and low loss, these tunable microwave components are being studied very intensely at NASA as well as the commercial communication industry. An assessment of the progress made so far, and the issues yet to be solved for the successful integration of these components into the aforementioned communication systems will be presented.

Present limits and improvements of structural materials for fusion reactors - a review

NASA Astrophysics Data System (ADS)

Tavassoli, A.-A. F.

2002-04-01

Since the transition from ITER or DEMO to a commercial power reactor would involve a significant change in system and materials options, a parallel R&D path has been put in place in Europe to address these issues. This paper assesses the structural materials part of this program along with the latest R&D results from the main programs. It is shown that stainless steels and ferritic/martensitic steels, retained for ITER and DEMO, will also remain the principal contenders for the future FPR, despite uncertainties over irradiation induced embrittlement at low temperatures and consequences of high He/dpa ratio. Neither one of the present advanced high temperature materials has to this date the structural integrity reliability needed for application in critical components. This situation is unlikely to change with the materials R&D alone and has to be mitigated in close collaboration with blanket system design.

Bargaining Agents in Wireless Contexts: An Alternating-Offers Protocol for Multi-issue Bilateral Negotiation in Mobile Marketplaces

NASA Astrophysics Data System (ADS)

Ragone, Azzurra; Ruta, Michele; di Sciascio, Eugenio; Donini, Francesco M.

We present an approach to multi-issue bilateral negotiation for mobile commerce scenarios. The negotiation mechanism has been integrated in a semantic-based application layer enhancing both RFID and Bluetooth wireless standards. OWL DL has been used to model advertisements and relationships among issues within a shared common ontology. Finally, non standard inference services integrated with utility theory help in finding suitable agreements. We illustrate and motivate the provided theoretical framework in a wireless commerce case study.

Research Project Evaluation-Learnings from the PATHWAYS Project Experience.

PubMed

Galas, Aleksander; Pilat, Aleksandra; Leonardi, Matilde; Tobiasz-Adamczyk, Beata

2018-05-25

Every research project faces challenges regarding how to achieve its goals in a timely and effective manner. The purpose of this paper is to present a project evaluation methodology gathered during the implementation of the Participation to Healthy Workplaces and Inclusive Strategies in the Work Sector (the EU PATHWAYS Project). The PATHWAYS project involved multiple countries and multi-cultural aspects of re/integrating chronically ill patients into labor markets in different countries. This paper describes key project's evaluation issues including: (1) purposes, (2) advisability, (3) tools, (4) implementation, and (5) possible benefits and presents the advantages of a continuous monitoring. Project evaluation tool to assess structure and resources, process, management and communication, achievements, and outcomes. The project used a mixed evaluation approach and included Strengths (S), Weaknesses (W), Opportunities (O), and Threats (SWOT) analysis. A methodology for longitudinal EU projects' evaluation is described. The evaluation process allowed to highlight strengths and weaknesses and highlighted good coordination and communication between project partners as well as some key issues such as: the need for a shared glossary covering areas investigated by the project, problematic issues related to the involvement of stakeholders from outside the project, and issues with timing. Numerical SWOT analysis showed improvement in project performance over time. The proportion of participating project partners in the evaluation varied from 100% to 83.3%. There is a need for the implementation of a structured evaluation process in multidisciplinary projects involving different stakeholders in diverse socio-environmental and political conditions. Based on the PATHWAYS experience, a clear monitoring methodology is suggested as essential in every multidisciplinary research projects.

Exploring MEDLINE Space with Random Indexing and Pathfinder Networks

PubMed Central

Cohen, Trevor

2008-01-01

The integration of disparate research domains is a prerequisite for the success of the translational science initiative. MEDLINE abstracts contain content from a broad range of disciplines, presenting an opportunity for the development of methods able to integrate the knowledge they contain. Latent Semantic Analysis (LSA) and related methods learn human-like associations between terms from unannotated text. However, their computational and memory demands limits their ability to address a corpus of this size. Furthermore, visualization methods previously used in conjunction with LSA have limited ability to define the local structure of the associative networks LSA learns. This paper explores these issues by (1) processing the entire MEDLINE corpus using Random Indexing, a variant of LSA, and (2) exploring learned associations using Pathfinder Networks. Meaningful associations are inferred from MEDLINE, including a drug-disease association undetected by PUBMED search. PMID:18999236

[Return to Work: A Workplace Focused Module to be Integrated in Cognitive Behavioral Therapy].

PubMed

Winter, Lotta; Kraft, Julia; Boss, Katharina; Kahl, Kai G

2015-08-01

Psychiatric disorders, in particular depression and anxiety disorders, are important causes of impaired job performance and increased sick leave. Longer periods of sickness leave lead regularly to difficulties concerning return to work. Furthermore, work is an important factor for psychological health. The central issue of the "return to work" (RTW) module by Lagerveldt and colleagues 5 is remission from psychiatric disorder, and structured support to return to work. The module is based on principles of cognitive-behavioral therapy (CBT), and can be integrated in standard CBT. Existing data from a randomized controlled trial suggest that treatment outcome concerning remission is similar between CBT supplemented with RTW (CBT-W) module and standard CBT. However, time to return to work is reduced in CBT-W. © Georg Thieme Verlag KG Stuttgart · New York.

Exploring MEDLINE space with random indexing and pathfinder networks.

PubMed

Cohen, Trevor

2008-11-06

The integration of disparate research domains is a prerequisite for the success of the translational science initiative. MEDLINE abstracts contain content from a broad range of disciplines, presenting an opportunity for the development of methods able to integrate the knowledge they contain. Latent Semantic Analysis (LSA) and related methods learn human-like associations between terms from unannotated text. However, their computational and memory demands limits their ability to address a corpus of this size. Furthermore, visualization methods previously used in conjunction with LSA have limited ability to define the local structure of the associative networks LSA learns. This paper explores these issues by (1) processing the entire MEDLINE corpus using Random Indexing, a variant of LSA, and (2) exploring learned associations using Pathfinder Networks. Meaningful associations are inferred from MEDLINE, including a drug-disease association undetected by PUBMED search.

Environmental Impact of Ionic Liquids: Recent Advances in (Eco)toxicology and (Bio)degradability.

PubMed

Costa, Susana P F; Azevedo, Ana M O; Pinto, Paula C A G; Saraiva, M Lúcia M F S

2017-06-09

This Review aims to integrate the most recent and pertinent data available on the (bio)degradability and toxicity of ionic liquids for global and critical analysis and on the conscious use of these compounds on a large scale thereafter. The integrated data will enable focus on the recognition of toxicophores and on the way the community has been dealing with them, with the aim to obtain greener and safer ionic liquids. Also, an update of the most recent biotic and abiotic methods developed to overcome some of these challenging issues will be presented. The review structure aims to present a potential sequence of events that can occur upon discharging ionic liquids into the environment and the potential long-term consequences. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Ethical issues in the reuse of qualitative data: perspectives from literature, practice, and participants.

PubMed

Yardley, Sarah J; Watts, Kate M; Pearson, Jennifer; Richardson, Jane C

2014-01-01

In this article, we explore ethical issues in qualitative secondary analysis through a comparison of the literature with practitioner and participant perspectives. To achieve this, we integrated critical narrative review findings with data from two discussion groups: qualitative researchers and research users/consumers. In the literature, we found that theoretical debate ran parallel to practical action rather than being integrated with it. We identified an important and novel theme of relationships that was emerging from the perspectives of researchers and users. Relationships were significant with respect to trust, sharing data, transparency and clarity, anonymity, permissions, and responsibility. We provide an example of practice development that we hope will prompt researchers to re-examine the issues in their own setting. Informing the research community of research practitioner and user perspectives on ethical issues in the reuse of qualitative data is the first step toward developing mechanisms to better integrate theoretical and empirical work.

Creating a course-based web site in a university environment

NASA Astrophysics Data System (ADS)

Robin, Bernard R.; Mcneil, Sara G.

1997-06-01

The delivery of educational materials is undergoing a remarkable change from the traditional lecture method to dissemination of courses via the World Wide Web. This paradigm shift from a paper-based structure to an electronic one has profound implications for university faculty. Students are enrolling in classes with the expectation of using technology and logging on to the Internet, and professors are realizing that the potential of the Web can have a significant impact on classroom activities. An effective method of integrating electronic technologies into teaching and learning is to publish classroom materials on the World Wide Web. Already, many faculty members are creating their own home pages and Web sites for courses that include syllabi, handouts, and student work. Additionally, educators are finding value in adding hypertext links to a wide variety of related Web resources from online research and electronic journals to government and commercial sites. A number of issues must be considered when developing course-based Web sites. These include meeting the needs of a target audience, designing effective instructional materials, and integrating graphics and other multimedia components. There are also numerous technical issues that must be addressed in developing, uploading and maintaining HTML documents. This article presents a model for a university faculty who want to begin using the Web in their teaching and is based on the experiences of two College of Education professors who are using the Web as an integral part of their graduate courses.

Organizational impact of nurse supply and workload on nurses continuing professional development opportunities: an integrative review.

PubMed

Coventry, Tracey H; Maslin-Prothero, Sian E; Smith, Gilly

2015-12-01

To identify the best evidence on the impact of healthcare organizations' supply of nurses and nursing workload on the continuing professional development opportunities of Registered Nurses in the acute care hospital. To maintain registration and professional competence nurses are expected to participate in continuing professional development. One challenge of recruitment and retention is the Registered Nurse's ability to participate in continuing professional development opportunities. The integrative review method was used to present Registered Nurses perspectives on this area of professional concern. The review was conducted for the period of 2001-February 2015. Keywords were: nurs*, continuing professional development, continuing education, professional development, supply, shortage, staffing, workload, nurse: patient ratio, barrier and deterrent. The integrative review used a structured approach for literature search and data evaluation, analysis and presentation. Eleven international studies met the inclusion criteria. Nurses are reluctant or prevented from leaving clinical settings to attend continuing professional development due to lack of relief cover, obtaining paid or unpaid study leave, use of personal time to undertake mandatory training and organizational culture and leadership issues constraining the implementation of learning to benefit patients. Culture, leadership and workload issues impact nurses' ability to attend continuing professional development. The consequences affect competence to practice, the provision of safe, quality patient care, maintenance of professional registration, job satisfaction, recruitment and retention. Organizational leadership plays an important role in supporting attendance at continuing professional development as an investment for the future. © 2015 John Wiley & Sons Ltd.

Integrated interdisciplinary training in the radiological sciences.

PubMed

Brenner, D J; Vazquez, M; Buonanno, M; Amundson, S A; Bigelow, A W; Garty, G; Harken, A D; Hei, T K; Marino, S A; Ponnaiya, B; Randers-Pehrson, G; Xu, Y

2014-02-01

The radiation sciences are increasingly interdisciplinary, both from the research and the clinical perspectives. Beyond clinical and research issues, there are very real issues of communication between scientists from different disciplines. It follows that there is an increasing need for interdisciplinary training courses in the radiological sciences. Training courses are common in biomedical academic and clinical environments, but are typically targeted to scientists in specific technical fields. In the era of multidisciplinary biomedical science, there is a need for highly integrated multidisciplinary training courses that are designed for, and are useful to, scientists who are from a mix of very different academic fields and backgrounds. We briefly describe our experiences running such an integrated training course for researchers in the field of biomedical radiation microbeams, and draw some conclusions about how such interdisciplinary training courses can best function. These conclusions should be applicable to many other areas of the radiological sciences. In summary, we found that it is highly beneficial to keep the scientists from the different disciplines together. In practice, this means not segregating the training course into sections specifically for biologists and sections specifically for physicists and engineers, but rather keeping the students together to attend the same lectures and hands-on studies throughout the course. This structure added value to the learning experience not only in terms of the cross fertilization of information and ideas between scientists from the different disciplines, but also in terms of reinforcing some basic concepts for scientists in their own discipline.

Understanding stakeholder important outcomes and perceptions of equity, acceptability and feasibility of a care model for haemophilia management in the US: a qualitative study.

PubMed

Lane, S J; Sholapur, N S; Yeung, C H T; Iorio, A; Heddle, N M; Sholzberg, M; Pai, M

2016-07-01

Care for persons with haemophilia (PWH) is most commonly delivered through the integrated care model used by Hemophilia Treatment Centers (HTCs). Although this model is widely accepted as the gold standard for the management of haemophilia; there is little evidence comparing different care models. We performed a qualitative study to gain insight into issues related to outcomes, acceptability, equity and feasibility of different care models operating in the US. We used a qualitative descriptive approach with semi-structured interviews. Purposive sampling was used to recruit individuals with experience providing or receiving care for haemophilia in the US through either an integrated care centre, a specialty pharmacy or homecare company, or by a specialist in a non-specialized centre. Persons with haemophilia, parents of PWH aged ≤18, healthcare providers, insurance company representatives and policy developers were invited to participate. Twenty-nine interviews were conducted with participants representing 18 US states. Participants in the study sample had experience receiving or providing care predominantly within an HTC setting. Integrated care at HTCs was highly acceptable to participants, who appreciated the value of specialized, expert care in a multidisciplinary team setting. Equity and feasibility issues were primarily related to health insurance and funding limitations. Additional research is required to document the impact of care on health and psychosocial outcomes and identify effective ways to facilitate equitable access to haemophilia treatment and care. © 2016 John Wiley & Sons Ltd.

A comparative review of environmental concern prioritization: LEED vs other major certification systems.

PubMed

Suzer, Ozge

2015-05-01

The matter of environmental concern prioritization integrated into globally used green building rating systems is a fundamental issue since it determines how the performance of a structure or development is reflected. Certain nationally-developed certification systems are used globally without being subjected to adjustments with respect to local geographical, cultural, economic and social parameters. This may lead to a situation where the results of an evaluation may not reflect the reality of the region and/or the site of construction. The main objective of this paper is to examine and underline the problems regarding the issue of weighting environmental concerns in the Leadership in Energy and Environmental Design (LEED) certification system, which is a US-originated but globally used assessment tool. The methodology of this study consists of; (i) an analysis of the approach of LEED in the New Construction and Major Renovations scheme in version 3 (LEED NC, v.3) and the Building Design and Construction scheme in version 4 (LEED BD + C, v.4), (ii) case studies in which regional priority credits (RPCs) set by LEED for four countries (Canada, Turkey, China and Egypt) are criticized with respect to countries' own local conditions, and, (iii) an analysis of the approaches of major environmental assessment tools, namely; BREEAM, SBTool, CASBEE and Green Star, in comparison to the approach in LEED, regarding the main issue of this paper. This work shows that, even in its latest version (v.4) LEED still displays some inadequacies and inconsistencies from the aspect of environmental concern prioritization and has not yet managed to incorporate a system which is more sensitive to this issue. This paper further outlines the differences and similarities between the approaches of the aforementioned major environmental assessment tools with respect to the issue of concern and the factors that should be integrated into future versions of LEED. Copyright © 2015 Elsevier Ltd. All rights reserved.

An Integrative Structural Health Monitoring System for the Local/Global Responses of a Large-Scale Irregular Building under Construction

PubMed Central

Park, Hyo Seon; Shin, Yunah; Choi, Se Woon; Kim, Yousok

2013-01-01

In this study, a practical and integrative SHM system was developed and applied to a large-scale irregular building under construction, where many challenging issues exist. In the proposed sensor network, customized energy-efficient wireless sensing units (sensor nodes, repeater nodes, and master nodes) were employed and comprehensive communications from the sensor node to the remote monitoring server were conducted through wireless communications. The long-term (13-month) monitoring results recorded from a large number of sensors (75 vibrating wire strain gauges, 10 inclinometers, and three laser displacement sensors) indicated that the construction event exhibiting the largest influence on structural behavior was the removal of bents that were temporarily installed to support the free end of the cantilevered members during their construction. The safety of each member could be confirmed based on the quantitative evaluation of each response. Furthermore, it was also confirmed that the relation between these responses (i.e., deflection, strain, and inclination) can provide information about the global behavior of structures induced from specific events. Analysis of the measurement results demonstrates the proposed sensor network system is capable of automatic and real-time monitoring and can be applied and utilized for both the safety evaluation and precise implementation of buildings under construction. PMID:23860317

Reducing barriers to mental health care for student-athletes: An integrated care model.

PubMed

Sudano, Laura E; Collins, Greg; Miles, Christopher M

2017-03-01

Research suggests that National Collegiate Athletic Association (NCAA) Division I student-athletes have higher levels of stress and other behavioral health issues, including substance use, than nonathletes. For several reasons, student-athletes may be less likely to admit to behavioral health issues and seek mental health care. Integrated care is a model of care that integrates behavioral health into a medical practice. This article explores the newly released NCAA Best Mental Health Practice guidelines and the application of integrated care to a Division I athletic training room setting using the three-worldview framework for successful integration, incorporating clinical outcomes, operational reliability, and financial stability. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Review on Malaysian Rail Transit Operation and Management System: Issues and Solution in Integration

NASA Astrophysics Data System (ADS)

Masirin, Mohd Idrus Mohd; Salin, Aminah Mohd; Zainorabidin, Adnan; Martin, David; Samsuddin, Norshakina

2017-08-01

In any context, operation and management of transportation systems are key issues which may affect both life quality and economic development. In large urban agglomerations, an efficient public transportation system may help abate the negative externalities of private car use such as congestion, air and noise pollution, accident and fuel consumption, without excessively penalizing user travel times or zone accessibility. Thus, this study is conducted to appraise the Malaysian rural rail transit operation and management system, which are considered important as there are many issues and solution in integration of the services that need to be tackled more conscientiously. The purpose of this paper is to describe some of the most important issues on integration of services and rail transit system in Malaysian and how to solve or reduce these problems and conflicts. In this paper, it consists of the historical development of rail transit construction in Malaysia. This paper also attempts to identify the important issues related to rail transit services and integration in Malaysian rural rail operation and management system. Comparison is also conducted with other countries such as UK, France, and Japan. Finally, a critical analysis is presented in this paper by looking at the possible application for future Malaysian rail transit operation system and management, especially focusing on enhancing the quality of Malaysian rural rail transit. In conclusion, this paper is expected to successfully review and appraise the existing Malaysian rural rail transit operation and management system pertaining to issues & solution in integration. It is also hoped that reformation or transformation of present service delivery quality of the rail transit operation and management will enable Malaysia to succeed in transforming Malaysian transportation system to greater heights.

Systematic Evaluation Program (SEP) at Rocky Flats Plant: An overview of practical management issues for evaluation of natural phenomena hazards

DOE Office of Scientific and Technical Information (OSTI.GOV)

Badwan, F.M.; Herring, K.S.

1993-08-01

Many of the buildings at the Rocky Flats Plant were designed and built before modern standards were developed, including standards for protection against extreme natural phenomenon such as tornadoes, earthquakes, and floods. The purpose of the SEP is to establish an integrated approach to assessing the design adequacy of specific high and moderate hazard Rocky Flats facilities from a safety perspective and to establish a basis for defining any needed facility improvements. The SEP is to be carried out in three Phases. In Phase 1, topics to be evaluated and an evaluation plan for each topic were developed. Any differencesmore » between Current Design Requirements (CDR) or acceptance criteria and the design of existing facilities, will be identified during Phase 2 and assessed using an integrated systematic approach during Phase 3. The integrated assessment performed during Phase 3 provides a process for evaluating the differences between existing facility design and CDRs so that decisions on corrective actions can be made on the basis of relative risk reduction and cost effectiveness. These efforts will ensure that a balanced and integrated level of safety is achieved for long-term operation of these buildings. Through appropriate selection of topics and identification of the structures, systems, and components to be evaluated, the SEP will address outstanding design issues related to the prevention and mitigation of design basis accidents, including those arising from natural phenomena. The objective of the SEP is not to bring these buildings into strict compliance with current requirements, but rather to ensure that an adequate level of safety is achieved in an economical fashion.« less

Cue Integration in Dynamic Decision Marking (Integration des indices dans la Prise de Decision Dynamique)

DTIC Science & Technology

2010-07-01

e.g., pulling the goalie in hockey). Outcomes are thought of as changes from a reference point- the reference point is itself changed by how the...challenges and training related issues can be pulled from the literature. These are discussed below. General Themes Cue integration involves the use...from our understanding of the term "pattern recognition", a number of general themes, challenges and training related issues can be pulled from the

Integration of analytical measurements and wireless communications--current issues and future strategies.

PubMed

Diamond, Dermot; Lau, King Tong; Brady, Sarah; Cleary, John

2008-05-15

Rapid developments in wireless communications are opening up opportunities for new ways to perform many types of analytical measurements that up to now have been restricted in scope due to the need to have access to centralised facilities. This paper will address both the potential for new applications and the challenges that currently inhibit more widespread integration of wireless communications with autonomous sensors and analytical devices. Key issues are identified and strategies for closer integration of analytical information and wireless communications systems discussed.

A cognitive perspective on health systems integration: results of a Canadian Delphi study

PubMed Central

2014-01-01

Background Ongoing challenges to healthcare integration point toward the need to move beyond structural and process issues. While we know what needs to be done to achieve integrated care, there is little that informs us as to how. We need to understand how diverse organizations and professionals develop shared knowledge and beliefs – that is, we need to generate knowledge about normative integration. We present a cognitive perspective on integration, based on shared mental model theory, that may enhance our understanding and ability to measure and influence normative integration. The aim of this paper is to validate and improve the Mental Models of Integrated Care (MMIC) Framework, which outlines important knowledge and beliefs whose convergence or divergence across stakeholder groups may influence inter-professional and inter-organizational relations. Methods We used a two-stage web-based modified Delphi process to test the MMIC Framework against expert opinion using a random sample of participants from Canada’s National Symposium on Integrated Care. Respondents were asked to rate the framework’s clarity, comprehensiveness, usefulness, and importance using seven-point ordinal scales. Spaces for open comments were provided. Descriptive statistics were used to describe the structured responses, while open comments were coded and categorized using thematic analysis. The Kruskall-Wallis test was used to examine cross-group agreement by level of integration experience, current workplace, and current role. Results In the first round, 90 individuals responded (52% response rate), representing a wide range of professional roles and organization types from across the continuum of care. In the second round, 68 individuals responded (75.6% response rate). The quantitative and qualitative feedback from experts was used to revise the framework. The re-named “Integration Mindsets Framework” consists of a Strategy Mental Model and a Relationships Mental Model, comprising a total of nineteen content areas. Conclusions The Integration Mindsets Framework draws the attention of researchers and practitioners to how various stakeholders think about and conceptualize integration. A cognitive approach to understanding and measuring normative integration complements dominant cultural approaches and allows for more fine-grained analyses. The framework can be used by managers and leaders to facilitate the interpretation, planning, implementation, management and evaluation of integration initiatives. PMID:24885659

A 3D Model for Eddy Current Inspection in Aeronautics: Application to Riveted Structures

NASA Astrophysics Data System (ADS)

Paillard, S.; Pichenot, G.; Lambert, M.; Voillaume, H.; Dominguez, N.

2007-03-01

Eddy current technique is currently an operational tool used for fastener inspection which is an important issue for the maintenance of aircraft structures. The industry calls for faster, more sensitive and reliable NDT techniques for the detection and characterization of potential flaws nearby rivet. In order to reduce the development time and to optimize the design and the performances assessment of an inspection procedure, the CEA and EADS have started a collaborative work aiming at extending the modeling features of the CIVA non destructive simulation plat-form in order to handle the configuration of a layered planar structure with a rivet and an embedded flaw nearby. Therefore, an approach based on the Volume Integral Method using the Green dyadic formalism which greatly increases computation efficiency has been developed. The first step, modeling the rivet without flaw as a hole in a multi-stratified structure, has been reached and validated in several configurations with experimental data.

Three-Dimensional Geometric Nonlinear Contact Stress Analysis of Riveted Joints

NASA Technical Reports Server (NTRS)

Shivakumar, Kunigal N.; Ramanujapuram, Vivek

1998-01-01

The problems associated with fatigue were brought into the forefront of research by the explosive decompression and structural failure of the Aloha Airlines Flight 243 in 1988. The structural failure of this airplane has been attributed to debonding and multiple cracking along the longitudinal lap splice riveted joint in the fuselage. This crash created what may be termed as a minor "Structural Integrity Revolution" in the commercial transport industry. Major steps have been taken by the manufacturers, operators and authorities to improve the structural airworthiness of the aging fleet of airplanes. Notwithstanding, this considerable effort there are still outstanding issues and concerns related to the formulation of Widespread Fatigue Damage which is believed to have been a contributing factor in the probable cause of the Aloha accident. The lesson from this accident was that Multiple-Site Damage (MSD) in "aging" aircraft can lead to extensive aircraft damage. A strong candidate in which MSD is highly probable to occur is the riveted lap joint.

An Integrated Interdisciplinary Faculty-Student Learning Community Focused on Water Issues: A Case Study

ERIC Educational Resources Information Center

Willermet, Cathy; Drake, Eron; Mueller, Anja; Juris, Stephen J.; Chhetri, Pratik; Upadhaya, Samik

2014-01-01

In response to a request from a campus student organization, faculty from three fields came together to develop and teach an integrated interdisciplinary course on water issues and social activism. This course, "Water as Life, Death, and Power," brought together topics from the fields of anthropology, biology and chemistry to explore…

Preservice Teachers' Reconciliation of an Epistemological Issue in an Integrated Mathematics/Science Methods Course

ERIC Educational Resources Information Center

Cormas, Peter C.

2017-01-01

Preservice teachers in six sections (n = 87) of a sequenced, methodological and process-integrated elementary mathematics/science methods course were able to reconcile an issue centered on a similar area of epistemology. Preservice teachers participated in a science inquiry lesson on biological classification and a mathematics problem-solving…

An Integrated Approach to Early Childhood Education and Care: A Preliminary Study. Occasional Paper.

ERIC Educational Resources Information Center

Haddad, Lenira

This paper reflects upon the policy development and implementation of integrated or coordinated services of early childhood education and care (ECEC) within a systemic perspective, focusing on issues of relevance to both developed and developing countries. The paper is divided into four parts: (1) issues related to ECEC's cultural and historical…

Preparing Pre-Service Teachers to Teach Primary Science: An Integrated Approach Using the Theme of Sustainability

ERIC Educational Resources Information Center

King, Donna

2014-01-01

An integrated approach to assessment afforded pre-service teachers the opportunity to learn about a local sustainability issue through three learning areas: science and technology, the arts and studies of society and environment (SOSE). Three sustainability issues chosen by the pre-service teachers are presented in this paper highlighting the…

Techniques: Integrating the National Issues Forums into ABE Programs.

ERIC Educational Resources Information Center

Colhapp, Barbara Jones

1989-01-01

This article discusses the National Issues Forum (NIF), a national, nonpartisan program designed to encourage citizen discussion of important public issues. The programs try to recreate the town meeting concept of reaching consensus on public issues. Short workbooks are available on two reading levels for issues such as the superpowers, crime,…

Issues Management and the Role of Strategic Planning. AIR 1985 Annual Forum Paper.

ERIC Educational Resources Information Center

Lozier, G. Gregory; Chittipeddi, Kumar

The integration of issues management into the institutional strategic planning process at Pennsylvania State University is discussed. The significance of issues management as an organizational process is also considered. Stages of the issues management process are: (1) scanning the external environment to identify strategic issues; (2) analyzing…

Applications of Advanced Nondestructive Measurement Techniques to Address Safety of Flight Issues on NASA Spacecraft

NASA Technical Reports Server (NTRS)

Prosser, Bill

2016-01-01

Advanced nondestructive measurement techniques are critical for ensuring the reliability and safety of NASA spacecraft. Techniques such as infrared thermography, THz imaging, X-ray computed tomography and backscatter X-ray are used to detect indications of damage in spacecraft components and structures. Additionally, sensor and measurement systems are integrated into spacecraft to provide structural health monitoring to detect damaging events that occur during flight such as debris impacts during launch and assent or from micrometeoroid and orbital debris, or excessive loading due to anomalous flight conditions. A number of examples will be provided of how these nondestructive measurement techniques have been applied to resolve safety critical inspection concerns for the Space Shuttle, International Space Station (ISS), and a variety of launch vehicles and unmanned spacecraft.

Making meaningful improvements to direct care worker training through informed policy: Understanding how care setting structure and culture matter.

PubMed

Kemeny, M Elizabeth; Mabry, J Beth

2017-01-01

Well-intentioned policy governing the training of direct care workers (DCWs) who serve older persons, in practice, may become merely a compliance issue for organizations rather than a meaningful way to improve quality of care. This study investigates the relationships between best practices in DCW training and the structure and culture of long term support service (LTSS) organizations. Using a mixed-methods approach to analyzing data from 328 licensed LTSS organizations in Pennsylvania, the findings suggest that public policy should address methods of training, not just content, and consider organizational variations in size, training evaluation practices, DCW integration, and DCW input into care planning. Effective training also incorporates support for organizations and supervisors as key aspects of DCWs' learning and working environment.

[Results and prospects of the guarantee of sanitary-epidemiological welfare of population of the Russian Federation].

PubMed

2012-01-01

The issues of further development of scientific and methodological basis of the guarantee of sanitary-epidemiological welfare of population of the Russian Federation are highlighted in accordance with the implementation of the Concept of the activity of the Federal Service for the Oversight of Consumer Protection and Welfare until 2015. Features of this work over the past 5 years have been characterized, they include: changes in the structure of the objects under surveillance; integration processes in the economy of the country rise of attention to social problems of society strengthening the influence of epidemiological and natural man-made disasters in the world and the country, improvement of the supervisory authorities of the Service, the formation of its new structure and development of legislative assembly, including sanitary legislation.

Analysis of Modeling Parameters on Threaded Screws.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vigil, Miquela S.; Brake, Matthew Robert; Vangoethem, Douglas

2015-06-01

Assembled mechanical systems often contain a large number of bolted connections. These bolted connections (joints) are integral aspects of the load path for structural dynamics, and, consequently, are paramount for calculating a structure's stiffness and energy dissipation prop- erties. However, analysts have not found the optimal method to model appropriately these bolted joints. The complexity of the screw geometry cause issues when generating a mesh of the model. This paper will explore different approaches to model a screw-substrate connec- tion. Model parameters such as mesh continuity, node alignment, wedge angles, and thread to body element size ratios are examined. Themore » results of this study will give analysts a better understanding of the influences of these parameters and will aide in finding the optimal method to model bolted connections.« less

Interaction, 1995-1996.

ERIC Educational Resources Information Center

Hajdu-Vaughn, Susan, Ed.

1996-01-01

These four quarterly journal issues, in both English and French language editions, explore issues related to child care practice and professional concerns. The Spring issue presents discussions on inclusion and successful integration; deals with topics such as effective management of day care facilities and safety issues; and provides ideas for…

Phronesis: Beyond the Research Ethics Committee-A Crucial Decision-Making Skill for Health Researchers During Community Research.

PubMed

Greeff, Minrie; Rennie, Stuart

2016-04-01

Health researchers conducting research in the community are often faced with unanticipated ethical issues that arise in the course of their research and that go beyond the scope of ethical approval by the research ethics committee. Eight expert researchers were selected through extreme intensity purposive sampling, because they are representative of unusual manifestations of the phenomenon related to their research in the community. They were selected to take part in a semi-structured focus group discussion on whether practical wisdom (phronesis) is used as a decision-making skill to solve unanticipated ethical issues during research in the community. Although the researchers were not familiar with the concept phronesis, it became obvious that it formed an integral part of their everyday existence and decision making during intervention research. They could balance research ethics with practical considerations. The capacity of practical wisdom as a crucial decision-making skill should be assimilated into a researcher's everyday reality, and also into the process of mentoring young researchers to become phronimos. Researchers should be taught this skill to handle unanticipated ethical issues. © The Author(s) 2016.

Smart grid as a service: a discussion on design issues.

PubMed

Chao, Hung-Lin; Tsai, Chen-Chou; Hsiung, Pao-Ann; Chou, I-Hsin

2014-01-01

Smart grid allows the integration of distributed renewable energy resources into the conventional electricity distribution power grid such that the goals of reduction in power cost and in environment pollution can be met through an intelligent and efficient matching between power generators and power loads. Currently, this rapidly developing infrastructure is not as "smart" as it should be because of the lack of a flexible, scalable, and adaptive structure. As a solution, this work proposes smart grid as a service (SGaaS), which not only allows a smart grid to be composed out of basic services, but also allows power users to choose between different services based on their own requirements. The two important issues of service-level agreements and composition of services are also addressed in this work. Finally, we give the details of how SGaaS can be implemented using a FIPA-compliant JADE multiagent system.

International Space Station (ISS) Accommodation of a Single US Assured Crew Return Vehicle (ACRV)

NASA Technical Reports Server (NTRS)

Mazanek, Daniel D.; Garn, Michelle A.; Troutman, Patrick A.; Wang, Yuan; Kumar, Renjith; Heck, Michael L.

1997-01-01

The following report was generated to give the International Space Station (ISS) Program some additional insight into the operations and issues associated with accommodating a single U.S. developed Assured Crew Return Vehicle (ACRV). During the generation of this report, changes in both the ISS and ACRV programs were factored into the analysis with the realization that most of the work performed will eventually need to be repeated once the two programs become more integrated. No significant issues associated with the ISS accommodating the ACRV were uncovered. Kinematic analysis of ACRV installation showed that there are viable methods of using Shuttle and Station robotic manipulators. Separation analysis demonstrated that the ACRV departure path clears the Station structure for all likely contingency scenarios. The payload bay packaging analysis identified trades that can be made between payload bay location, Shuttle Remote Manipulator System (SRMS) reach and eventual designs of de-orbit stages and docking adapters.

A Meta-analysis Method to Advance Design of Technology-Based Learning Tool: Combining Qualitative and Quantitative Research to Understand Learning in Relation to Different Technology Features

NASA Astrophysics Data System (ADS)

Zhang, Lin

2014-02-01

Educators design and create various technology tools to scaffold students' learning. As more and more technology designs are incorporated into learning, growing attention has been paid to the study of technology-based learning tool. This paper discusses the emerging issues, such as how can learning effectiveness be understood in relation to different technology features? And how can pieces of qualitative and quantitative results be integrated to achieve a broader understanding of technology designs? To address these issues, this paper proposes a meta-analysis method. Detailed explanations about the structure of the methodology and its scientific mechanism are provided for discussions and suggestions. This paper ends with an in-depth discussion on the concerns and questions that educational researchers might raise, such as how this methodology takes care of learning contexts.

Examining the Multi-level Fit between Work and Technology in a Secure Messaging Implementation.

PubMed

Ozkaynak, Mustafa; Johnson, Sharon; Shimada, Stephanie; Petrakis, Beth Ann; Tulu, Bengisu; Archambeault, Cliona; Fix, Gemmae; Schwartz, Erin; Woods, Susan

2014-01-01

Secure messaging (SM) allows patients to communicate with their providers for non-urgent health issues. Like other health information technologies, the design and implementation of SM should account for workflow to avoid suboptimal outcomes. SM may present unique workflow challenges because patients add a layer of complexity, as they are also direct users of the system. This study explores SM implementation at two Veterans Health Administration facilities. We interviewed twenty-nine members of eight primary care teams using semi-structured interviews. Questions addressed staff opinions about the integration of SM with daily practice, and team members' attitudes and experiences with SM. We describe the clinical workflow for SM, examining complexity and variability. We identified eight workflow issues directly related to efficiency and patient satisfaction, based on an exploration of the technology fit with multilevel factors. These findings inform organizational interventions that will accommodate SM implementation and lead to more patient-centered care.

CFD for hypersonic propulsion

NASA Technical Reports Server (NTRS)

Povinelli, Louis A.

1991-01-01

An overview is given of research activity on the application of computational fluid dynamics (CDF) for hypersonic propulsion systems. After the initial consideration of the highly integrated nature of air-breathing hypersonic engines and airframe, attention is directed toward computations carried out for the components of the engine. A generic inlet configuration is considered in order to demonstrate the highly three dimensional viscous flow behavior occurring within rectangular inlets. Reacting flow computations for simple jet injection as well as for more complex combustion chambers are then discussed in order to show the capability of viscous finite rate chemical reaction computer simulations. Finally, the nozzle flow fields are demonstrated, showing the existence of complex shear layers and shock structure in the exhaust plume. The general issues associated with code validation as well as the specific issue associated with the use of CFD for design are discussed. A prognosis for the success of CFD in the design of future propulsion systems is offered.

CFD for hypersonic propulsion

NASA Technical Reports Server (NTRS)

Povinelli, Louis A.

1990-01-01

An overview is given of research activity on the application of computational fluid dynamics (CDF) for hypersonic propulsion systems. After the initial consideration of the highly integrated nature of air-breathing hypersonic engines and airframe, attention is directed toward computations carried out for the components of the engine. A generic inlet configuration is considered in order to demonstrate the highly three dimensional viscous flow behavior occurring within rectangular inlets. Reacting flow computations for simple jet injection as well as for more complex combustion chambers are then discussed in order to show the capability of viscous finite rate chemical reaction computer simulations. Finally, the nozzle flow fields are demonstrated, showing the existence of complex shear layers and shock structure in the exhaust plume. The general issues associated with code validation as well as the specific issue associated with the use of CFD for design are discussed. A prognosis for the success of CFD in the design of future propulsion systems is offered.

Smart Grid as a Service: A Discussion on Design Issues

PubMed Central

Tsai, Chen-Chou; Chou, I-Hsin

2014-01-01

Smart grid allows the integration of distributed renewable energy resources into the conventional electricity distribution power grid such that the goals of reduction in power cost and in environment pollution can be met through an intelligent and efficient matching between power generators and power loads. Currently, this rapidly developing infrastructure is not as “smart” as it should be because of the lack of a flexible, scalable, and adaptive structure. As a solution, this work proposes smart grid as a service (SGaaS), which not only allows a smart grid to be composed out of basic services, but also allows power users to choose between different services based on their own requirements. The two important issues of service-level agreements and composition of services are also addressed in this work. Finally, we give the details of how SGaaS can be implemented using a FIPA-compliant JADE multiagent system. PMID:25243214

Rio + 5 -- INSTRAW's activities regarding the implementation of Agenda 21.

PubMed

1997-01-01

The International Research and Training Institute for the Advancement of Women (INSTRAW) was involved in research analysis and training activities that address women's issues on water supply, sanitation and waste management, development of new and renewable sources of energy, and natural resources since 1982. The four main thrusts of the INSTRAW program include: 1) the economic and political empowerment of the women; 2) women, media and communications; 3) women, environment and sustainable development; and 4) statistics and indicators on gender issues. These areas are approached in an integrated and holistic manner, which is crosscutting and cross disciplinary with relevant chapters Agenda 21. In addition, poverty, population growth, health, structural adjustment policies, education and training, water, energy, agriculture and forestry are addressed within the women's roles and activities context. This article presents an overview of the succeeding chapters, which focus on the programs developed and implemented to promote the well being of the women worldwide.

Integrated Arts Curriculum in Hong Kong Secondary Schools

ERIC Educational Resources Information Center

Wong, Marina Wai-yee

2012-01-01

This longitudinal study (2001-09) of two Hong Kong secondary schools highlights six issues with an integrated arts curriculum: first, integration of knowledge and skills negatively precedes the integration of learners' construction of meaning; second, integration is perceived as challenging the profession's status; third, teachers are unaccustomed…

Surface-based reconstruction and diffusion MRI in the assessment of gray and white matter damage in multiple sclerosis

NASA Astrophysics Data System (ADS)

Caffini, Matteo; Bergsland, Niels; LaganÃ, Marcella; Tavazzi, Eleonora; Tortorella, Paola; Rovaris, Marco; Baselli, Giuseppe

2014-03-01

Despite advances in the application of nonconventional MRI techniques in furthering the understanding of multiple sclerosis pathogenic mechanisms, there are still many unanswered questions, such as the relationship between gray and white matter damage. We applied a combination of advanced surface-based reconstruction and diffusion tensor imaging techniques to address this issue. We found significant relationships between white matter tract integrity indices and corresponding cortical structures. Our results suggest a direct link between damage in white and gray matter and contribute to the notion of gray matter loss relating to clinical disability.

Integrating industrial seminars within a graduate engineering programme

NASA Astrophysics Data System (ADS)

Ringwood, John. V.

2013-05-01

The benefit of external, often industry-based, speakers for a seminar series associated with both undergraduate and graduate programmes is relatively unchallenged. However, the means by which such a seminar series can be encapsulated within a structured learning module, and the appropriate design of an accompanying assessment methodology, is not so obvious. This paper examines how such a learning module can be formulated and addresses the main issues involved in the design of such a module, namely the selection of speakers, format of seminars, method of delivery and assessment methodology, informed by the objectives of the module.

Bridge Structure Deformation Prediction Based on GNSS Data Using Kalman-ARIMA-GARCH Model

PubMed Central

Li, Xiaoqing; Wang, Yu

2018-01-01

Bridges are an essential part of the ground transportation system. Health monitoring is fundamentally important for the safety and service life of bridges. A large amount of structural information is obtained from various sensors using sensing technology, and the data processing has become a challenging issue. To improve the prediction accuracy of bridge structure deformation based on data mining and to accurately evaluate the time-varying characteristics of bridge structure performance evolution, this paper proposes a new method for bridge structure deformation prediction, which integrates the Kalman filter, autoregressive integrated moving average model (ARIMA), and generalized autoregressive conditional heteroskedasticity (GARCH). Firstly, the raw deformation data is directly pre-processed using the Kalman filter to reduce the noise. After that, the linear recursive ARIMA model is established to analyze and predict the structure deformation. Finally, the nonlinear recursive GARCH model is introduced to further improve the accuracy of the prediction. Simulation results based on measured sensor data from the Global Navigation Satellite System (GNSS) deformation monitoring system demonstrated that: (1) the Kalman filter is capable of denoising the bridge deformation monitoring data; (2) the prediction accuracy of the proposed Kalman-ARIMA-GARCH model is satisfactory, where the mean absolute error increases only from 3.402 mm to 5.847 mm with the increment of the prediction step; and (3) in comparision to the Kalman-ARIMA model, the Kalman-ARIMA-GARCH model results in superior prediction accuracy as it includes partial nonlinear characteristics (heteroscedasticity); the mean absolute error of five-step prediction using the proposed model is improved by 10.12%. This paper provides a new way for structural behavior prediction based on data processing, which can lay a foundation for the early warning of bridge health monitoring system based on sensor data using sensing technology. PMID:29351254

Bridge Structure Deformation Prediction Based on GNSS Data Using Kalman-ARIMA-GARCH Model.

PubMed

Xin, Jingzhou; Zhou, Jianting; Yang, Simon X; Li, Xiaoqing; Wang, Yu

2018-01-19

Bridges are an essential part of the ground transportation system. Health monitoring is fundamentally important for the safety and service life of bridges. A large amount of structural information is obtained from various sensors using sensing technology, and the data processing has become a challenging issue. To improve the prediction accuracy of bridge structure deformation based on data mining and to accurately evaluate the time-varying characteristics of bridge structure performance evolution, this paper proposes a new method for bridge structure deformation prediction, which integrates the Kalman filter, autoregressive integrated moving average model (ARIMA), and generalized autoregressive conditional heteroskedasticity (GARCH). Firstly, the raw deformation data is directly pre-processed using the Kalman filter to reduce the noise. After that, the linear recursive ARIMA model is established to analyze and predict the structure deformation. Finally, the nonlinear recursive GARCH model is introduced to further improve the accuracy of the prediction. Simulation results based on measured sensor data from the Global Navigation Satellite System (GNSS) deformation monitoring system demonstrated that: (1) the Kalman filter is capable of denoising the bridge deformation monitoring data; (2) the prediction accuracy of the proposed Kalman-ARIMA-GARCH model is satisfactory, where the mean absolute error increases only from 3.402 mm to 5.847 mm with the increment of the prediction step; and (3) in comparision to the Kalman-ARIMA model, the Kalman-ARIMA-GARCH model results in superior prediction accuracy as it includes partial nonlinear characteristics (heteroscedasticity); the mean absolute error of five-step prediction using the proposed model is improved by 10.12%. This paper provides a new way for structural behavior prediction based on data processing, which can lay a foundation for the early warning of bridge health monitoring system based on sensor data using sensing technology.

The SDGs Will Require Integrated Agriculture, Nutrition, and Health at the Community Level.

PubMed

Canavan, Chelsey R; Graybill, Lauren; Fawzi, Wafaie; Kinabo, Joyce

2016-03-01

Child malnutrition is an urgent and complex issue and requires integrated approaches across agriculture, nutrition, and health. This issue has gained prominence at the global level. While national-level efforts are underway in many countries, there is little information on how to integrate at the community level. Here, we offer a community-based approach using cadres of agricultural and community health workers, drawing on qualitative work we have conducted in Tanzania. Agriculture is an important driver of nutritional and health outcomes, and improving child health will require practical solutions for integration that can add to the evidence base. © The Author(s) 2016.

Impairments in Skin Integrity.

PubMed

Murphree, Rose W

2017-09-01

Altered skin integrity increases the chance of infection, impaired mobility, and decreased function and may result in the loss of limb or, sometimes, life. Skin is affected by both intrinsic and extrinsic factors. Intrinsic factors can include altered nutritional status, vascular disease issues, and diabetes. Extrinsic factors include falls, accidents, pressure, immobility, and surgical procedures. Ensuring skin integrity in the elderly requires a team approach and includes the individual, caregivers, and clinicians. The twenty-first century clinician has several online, evidence-based tools to assist with optimal treatment plans. Understanding best practices in addressing skin integrity issues can promote positive outcomes with the elderly. Copyright © 2017 Elsevier Inc. All rights reserved.

Pervasive genetic integration directs the evolution of human skull shape.

PubMed

Martínez-Abadías, Neus; Esparza, Mireia; Sjøvold, Torstein; González-José, Rolando; Santos, Mauro; Hernández, Miquel; Klingenberg, Christian Peter

2012-04-01

It has long been unclear whether the different derived cranial traits of modern humans evolved independently in response to separate selection pressures or whether they resulted from the inherent morphological integration throughout the skull. In a novel approach to this issue, we combine evolutionary quantitative genetics and geometric morphometrics to analyze genetic and phenotypic integration in human skull shape. We measured human skulls in the ossuary of Hallstatt (Austria), which offer a unique opportunity because they are associated with genealogical data. Our results indicate pronounced covariation of traits throughout the skull. Separate simulations of selection for localized shape changes corresponding to some of the principal derived characters of modern human skulls produced outcomes that were similar to each other and involved a joint response in all of these traits. The data for both genetic and phenotypic shape variation were not consistent with the hypothesis that the face, cranial base, and cranial vault are completely independent modules but relatively strongly integrated structures. These results indicate pervasive integration in the human skull and suggest a reinterpretation of the selective scenario for human evolution where the origin of any one of the derived characters may have facilitated the evolution of the others. © 2011 The Author(s). Evolution© 2011 The Society for the Study of Evolution.

From collision to collaboration - Integrating informal recyclers and re-use operators in Europe: A review.

PubMed

Scheinberg, Anne; Nesić, Jelena; Savain, Rachel; Luppi, Pietro; Sinnott, Portia; Petean, Flaviu; Pop, Flaviu

2016-09-01

The European Union hosts some of the world's most developed waste management systems and an ambitious policy commitment to the circular economy. The existence of informal recycling and re-use activities in Europe has been vigorously denied until quite recently, and remains a very challenging subject for the European solid waste management sector, as well as for European government and private institutions. In countries ranging from Malta to Macedonia and from France to Turkey, informal recyclers excluded from legal recycling niches increasingly collide with formalised and controlled European Union approaches to urban waste management, packaging recovery schemes, formal re-use enterprises, and extended producer responsibility systems.This review focuses on the period from 2004 through the first half of 2016. The 78 sources on European (and neighbouring) informal recycling and re-use are contextualised with global sources and experience. The articles focus on informal recovery in and at the borders of the European Union, document the conflicts and collisions, and elaborate some constructive approaches towards legalisation, integration, and reconciliation. The overarching recommendation, to locate the issue of informal recovery and integration in the framework of the European circular economy package, is supported by four specific pillars of an integration strategy: Documentation, legalisation, occupational and enterprise recognition, and preparation for structural integration. © The Author(s) 2016.

Research Library Issues: A Report from ARL, CNI, and SPARC. RLI 283

ERIC Educational Resources Information Center

Baughman, M. Sue, Ed.

2013-01-01

"Research Library Issues" ("RLI") focuses on current and emerging topics that are strategically important to research libraries. The articles explore issues, share information, pose critical questions, and provide examples. This issue includes the following articles: (1) Special at the Core: Aligning, Integrating, and…

Generating a focused view of disease ontology cancer terms for pan-cancer data integration and analysis

PubMed Central

Wu, Tsung-Jung; Schriml, Lynn M.; Chen, Qing-Rong; Colbert, Maureen; Crichton, Daniel J.; Finney, Richard; Hu, Ying; Kibbe, Warren A.; Kincaid, Heather; Meerzaman, Daoud; Mitraka, Elvira; Pan, Yang; Smith, Krista M.; Srivastava, Sudhir; Ward, Sari; Yan, Cheng; Mazumder, Raja

2015-01-01

Bio-ontologies provide terminologies for the scientific community to describe biomedical entities in a standardized manner. There are multiple initiatives that are developing biomedical terminologies for the purpose of providing better annotation, data integration and mining capabilities. Terminology resources devised for multiple purposes inherently diverge in content and structure. A major issue of biomedical data integration is the development of overlapping terms, ambiguous classifications and inconsistencies represented across databases and publications. The disease ontology (DO) was developed over the past decade to address data integration, standardization and annotation issues for human disease data. We have established a DO cancer project to be a focused view of cancer terms within the DO. The DO cancer project mapped 386 cancer terms from the Catalogue of Somatic Mutations in Cancer (COSMIC), The Cancer Genome Atlas (TCGA), International Cancer Genome Consortium, Therapeutically Applicable Research to Generate Effective Treatments, Integrative Oncogenomics and the Early Detection Research Network into a cohesive set of 187 DO terms represented by 63 top-level DO cancer terms. For example, the COSMIC term ‘kidney, NS, carcinoma, clear_cell_renal_cell_carcinoma’ and TCGA term ‘Kidney renal clear cell carcinoma’ were both grouped to the term ‘Disease Ontology Identification (DOID):4467 / renal clear cell carcinoma’ which was mapped to the TopNodes_DOcancerslim term ‘DOID:263 / kidney cancer’. Mapping of diverse cancer terms to DO and the use of top level terms (DO slims) will enable pan-cancer analysis across datasets generated from any of the cancer term sources where pan-cancer means including or relating to all or multiple types of cancer. The terms can be browsed from the DO web site (http://www.disease-ontology.org) and downloaded from the DO’s Apache Subversion or GitHub repositories. Database URL: http://www.disease-ontology.org PMID:25841438

Psychiatric Mental Health Leadership at the Tipping Point.

PubMed

R Delaney, Kathleen

2015-05-01

Currently the United States health care system is responding to the Patient Protection and Affordable Care Act (PPACA) and the vision it contains for health care transformation. Along with sweeping changes in service delivery and payment structures, health care reform has championed concepts such as patient-centered care, integrated care, and wellness. Although these are not new ideas, their adaptation, in both ideology and service design has been accelerated in the context for reform. Indeed they are reaching a tipping point; the point where ideas gain wide acceptance and become influential trends. Although psychiatric mental health (PMH) nurses have been active in wellness, patient-centered care, and integrated care, at the current time they seem to be situated peripheral to these national trends. Increased presence of PMH nurses will facilitate their contribution to the development of these concepts within service structures and interventions. To increase knowledge and appreciation of PMH nurses' practice and unique perspective on these issues, leaders are needed who will connect and effectively communicate PMH nursing efforts to the broader health care arena. This article outlines the events that created a context for these three concepts (patient-centered care, wellness, and integrated care), and I suggest why they have reached a tipping point and discuss the need for greater PMH nursing presence in the American national dialog and the role of nursing leaders in facilitating these connections.

Economic analysis for transmission operation and planning

NASA Astrophysics Data System (ADS)

Zhou, Qun

2011-12-01

Restructuring of the electric power industry has caused dramatic changes in the use of transmission system. The increasing congestion conditions as well as the necessity of integrating renewable energy introduce new challenges and uncertainties to transmission operation and planning. Accurate short-term congestion forecasting facilitates market traders in bidding and trading activities. Cost sharing and recovery issue is a major impediment for long-term transmission investment to integrate renewable energy. In this research, a new short-term forecasting algorithm is proposed for predicting congestion, LMPs, and other power system variables based on the concept of system patterns. The advantage of this algorithm relative to standard statistical forecasting methods is that structural aspects underlying power market operations are exploited to reduce the forecasting error. The advantage relative to previously proposed structural forecasting methods is that data requirements are substantially reduced. Forecasting results based on a NYISO case study demonstrate the feasibility and accuracy of the proposed algorithm. Moreover, a negotiation methodology is developed to guide transmission investment for integrating renewable energy. Built on Nash Bargaining theory, the negotiation of investment plans and payment rate can proceed between renewable generation and transmission companies for cost sharing and recovery. The proposed approach is applied to Garver's six bus system. The numerical results demonstrate fairness and efficiency of the approach, and hence can be used as guidelines for renewable energy investors. The results also shed light on policy-making of renewable energy subsidies.