Serrated kiln sticks and top load substantially reduce warp in southern pine studs dried at 240°F

Treesearch

P. Koch

1974-01-01

Sharply toothed luminum kiln sticks pressed into 2 by 4's cut from veneer cores, willi a clamping force of 50 to 200 pounds per stick-pair per stud, significantly reduced warp from that observed in matched studs stacked on smooth sticks with a top load of 10 pounds per stick-pair per stud. When dried in 24 hours to an average MC of 8.1 percent (standard deviation...

Conduction cooled tube supports

DOEpatents

Worley, Arthur C.; Becht, IV, Charles

1984-01-01

In boilers, process tubes are suspended by means of support studs that are in thermal contact with and attached to the metal roof casing of the boiler and the upper bend portions of the process tubes. The support studs are sufficiently short that when the boiler is in use, the support studs are cooled by conduction of heat to the process tubes and the roof casing thereby maintaining the temperature of the stud so that it does not exceed 1400.degree. F.

Technology Solutions Case Study: Monitoring of Double Stud Wall Moisture Conditions in the Northeast, Devens, Massachusetts

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2015-03-01

Double stud walls have a higher risk of interior-sourced condensation moisture damage when compared with high-R approaches using exterior insulating sheathing. In this project, Building Science Corporation monitored moisture conditions in double-stud walls from 2011 through 2014 at a new production house located in Devens, Massachusetts. The builder, Transformations, Inc., has been using double-stud walls insulated with 12 in. of open cell polyurethane spray foam (ocSPF); however, the company has been considering a change to netted and blown cellulose insulation for cost reasons. Cellulose is a common choice for double-stud walls because of its lower cost (in most markets). However,more » cellulose is an air-permeable insulation, unlike spray foams, which increases interior moisture risks. The team compared three double-stud assemblies: 12 in. of ocSPF, 12 in. of cellulose, and 5-½ in. of ocSPF at the exterior of a double-stud wall (to approximate conventional 2 × 6 wall construction and insulation levels, acting as a control wall). These assemblies were repeated on the north and south orientations, for a total of six assemblies.« less

The effects of studded tires on fatal crashes with passenger cars and the benefits of electronic stability control (ESC) in Swedish winter driving.

PubMed

Strandroth, Johan; Rizzi, Matteo; Olai, Maria; Lie, Anders; Tingvall, Claes

2012-03-01

This study set out to examine the effects of studded tires on fatal crashes on roads covered with ice or snow in Sweden and also to investigate the extra benefits of electronic stability control (ESC) during the winter months. Two different studies are presented in this paper. Both studies used an induced exposure approach. In the main study, 369 in-depth studies of fatal crashes with passenger cars were analyzed to determine whether loss-of-control (LOC) had been a major component or not. Only crashes involving cars without ESC and equipped with approved studded or non-studded winter tires were analyzed. The additional study used police-reported crashes that occurred during the winter seasons 2003-2010, involving passenger cars with and without ESC. While police records in Sweden do not include any tire information, it was assumed that most cars involved in crashes during the winter period would be equipped with studded tires. Findings in the main study showed that in 64% of the fatal crashes on roads covered with ice or snow LOC had been a major component. Furthermore, in 82% of LOC crashes, the passenger car over-steered prior to collision. Studded tires were found to have a statistically significant effect of 42% in terms of fatal crash reduction on roads covered with ice or snow, compared to non-studded winter tires. The effect on dry or wet roads in the winter was negative, although statistically non-significant. In the additional study, it was found that ESC further reduced crashes with injuries by 29%. The benefits on severe and fatal crashes were slightly greater (32%), although the lower 95% confidence limit was lower. Although studded tires were shown to reduce the risk of fatal crash involvement, compared to non-studded winter tires, the proportion of LOC and over-steering among cars with studded tires was large (59% and 49%, respectively). It was therefore concluded that studded tires do not prevent all LOC crashes, while ESC has benefits in those crashes since this technology mostly addresses over-steering. This is also supported by the fact that the share of LOC fatal crashes is considerably lower for ESC-equipped cars. This study recommends that non-ESC cars should be fitted with studded tires if they are to be driven on roads covered by ice or snow. If the proportion of studded tires is to be decreased on Swedish roads to reduce the about of hazardous particulates especially in built up areas, from a road safety point of view it is recommended that this should be done in phase with the implementation of ESC on all passenger cars. Copyright © 2011 Elsevier Ltd. All rights reserved.

Simulations of stress evolution and the current density scaling of electromigration-induced failure times in pure and alloyed interconnects

NASA Astrophysics Data System (ADS)

Park, Young-Joon; Andleigh, Vaibhav K.; Thompson, Carl V.

1999-04-01

An electromigration model is developed to simulate the reliability of Al and Al-Cu interconnects. A polynomial expression for the free energy of solution by Murray [Int. Met. Rev. 30, 211 (1985)] was used to calculate the chemical potential for Al and Cu while the diffusivities were defined based on a Cu-trapping model by Rosenberg [J. Vac. Sci. Technol. 9, 263 (1972)]. The effects of Cu on stress evolution and lifetime were investigated in all-bamboo and near-bamboo stud-to-stud structures. In addition, the significance of the effect of mechanical stress on the diffusivity of both Al and Cu was determined in all-bamboo and near-bamboo lines. The void nucleation and growth process was simulated in 200 μm, stud-to-stud lines. Current density scaling behavior for void-nucleation-limited failure and void-growth-limited failure modes was simulated in long, stud-to-stud lines. Current density exponents of both n=2 for void nucleation and n=1 for void growth failure modes were found in both pure Al and Al-Cu lines. Limitations of the most widely used current density scaling law (Black's equation) in the analysis of the reliability of stud-to-stud lines are discussed. By modifying the input materials properties used in this model (when they are known), this model can be adapted to predict the reliability of other interconnect materials such as pure Cu and Cu alloys.

Vehicle non-exhaust emissions from the tyre-road interface - effect of stud properties, traction sanding and resuspension

NASA Astrophysics Data System (ADS)

Kupiainen, Kaarle J.; Pirjola, Liisa

2011-08-01

In Northern cities respirable street dust emission levels (PM 10) are especially high during spring. The spring time dust has been observed to cause health effects as well as discomfort among citizens. Major sources of the dust are the abrasion products from the pavement and traction sand aggregates that are formed due to the motion of the tyre. We studied the formation of respirable abrasion particles in the tyre-road interface due to tyre studs and traction sanding by a mobile laboratory vehicle Sniffer. The measurements were preformed on a test track, where the influence of varying stud weight and stud number per tyre on PM 10 emissions was studied. Studded tyres resulted in higher emission levels than studless tyres especially with speeds 50 km h -1 and higher; however, by using light weight studs, which approximately halves the weight of studs, or by reducing the number of studs per tyre to half, the emission levels decreased by approximately half. Additionally measurements were done with and without traction sand coverage on the pavement of a public road. After traction sanding the emission levels were not affected by tyre type but by formation and suspension of traction sand related dust from the road surface. The emissions after traction sanding decreased as a function of time as passing vehicles' motion shifted the sand grains away from the areas with most tyre-road contact.

Repair of rutting caused by studded tires : literature review.

DOT National Transportation Integrated Search

1995-07-01

Rutting caused by studded tire wear has become a major issue in Oregon because of the impact on the infrastructure and the increase in driving hazards. It is estimated that the cost to mitigate the damage from studded tire use in 1993 alone is $42 mi...

Studded and unstudded winter tires in fatal road accidents in Finland.

PubMed

Malmivuo, Mikko; Luoma, Juha; Porthin, Markus

2017-07-04

The aim of the study was to compare the safety effects of studded and unstudded winter tires based on fatal road accidents. The data included 958 road accidents involving a passenger car or van that occurred in Finland from November to March between 1997 and 2012. Comparing the proportions of winter tire type in accidents and in general traffic showed that the overall effect of tire type on the number of accidents was not significant, although studded tires reduced fatal accidents by 10-15%. Compared to unstudded tires, studded tires reduced accidents significantly only on bald ice in 2005-2012. Drivers using unstudded tires were more experienced and their profession was more frequently related to driving. In addition, the vehicle age was lower for vehicles with unstudded tires. On the other hand, the state of repair was less pertinent for unstudded than for studded tires. These confounding factors offset their effects to some degree. The risk of fatal road accidents in winter between studded and unstudded tires does not differ significantly. However, the accident risk has recently been substantially higher on bald ice for unstudded than for studded tires. The magnitude of this risk difference is difficult to determine without specific information on exposure by road surface.

Implementation of STUD Pulses at the Trident Laser and Initial Results

NASA Astrophysics Data System (ADS)

Johnson, R. P.; Shimada, T.; Montgomery, D. S.; Afeyan, B.; Hüller, S.

2012-10-01

Controlling and mitigating laser-plasma instabilities such as stimulated Brillouin scattering, stimulated Raman scattering, and crossed-beam energy transfer is important to achieve high-gain inertial fusion using laser drivers. Recent theory and simulations show that these instabilities can be largely controlled using laser pulses consisting of spike trains of uneven duration and delay (STUD) by modulating the laser on a picosecond time scale [1,2]. We have designed and implemented a STUD pulse generator at the LANL Trident Laser Facility using Fourier synthesis to produce a 0.5-ns envelope of psec-duration STUD pulses using a spatial light modulator. Initial results from laser propagation tests and measurements as well as initial laser-plasma characterization experiments will be presented.[4pt] [1] B. Afeyan and S. H"uller, ``Optimal Control of Laser Plasma Instabilities using STUD pulses,'' IFSA 2011, P.Mo.1, to appear in Euro. Phys. J. Web of Conf. (2012).[2] S. H"uller and B. Afeyan, ``Simulations of drastically reduced SBS with STUD pulses,'' IFSA 2011, O.Tu8-1, to appear in Euro. Phys. J. Web of Conf. (2012).

Study on Shear Performance of Cold-formed Steel Composite Wall with New Type of stud

NASA Astrophysics Data System (ADS)

Wang, Chungang; Yue, Sizhe; Liu, Hong; Zhang, Zhuangnan

2018-03-01

The shear resistance of single oriented-strand board wall and single gypsum board wall can be improved in different degrees by increasing strength of steel. The experimental data of literatures were used, and the test specimens had been simulated and validated by ABAQUS finite element analysis. According to the research, it showed that the compressive bearing capacity of the new stud composite wall was much better than the common stud composite wall, so the establishment and research of all models had been based on the new section stud. The analysis results show that when using new type of stud the shear resistance of the single oriented-strand board wall can be improved efficiently by increasing strength of steel, but the shear resistance of the single gypsum wall can be increased little.

Motor-driven screwing and transporting tool for reactor pressure vessel head retaining fastenings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scholz, M.

1977-09-13

The invention concerns a motor-driven screwing and transporting tool for tightening or loosening the threaded studs and associated tightening nuts of the head bolting of pressure vessels. After the tightening nuts are loosened or before they are tightened, the weight of the studs is taken over by rotating bearings that can be lifted, so that the studs with their tightening nuts can be screwed in or out, the screw threads of the studs being thus weight-relieved. The invention is intended primarily for nuclear reactor pressure vessels. 21 claims, 6 figures.

Straight studs are produced from southern pine cordwood

Treesearch

Peter Koch

1967-01-01

A Process for converting southern pine veneer cores into 8-foot 2 by 4's of SPIB Stud grade and better has been developed at the Alexandria, Louisiana, Utilization Laboratory of the Southern Forest Experiment Station. The research leading to this development suggests that a similiar process would be practical for converting 8-foot southern pine cordwood into studs...

46 CFR 56.25-20 - Bolting.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., Blanks, Flange Facings, Gaskets, and Bolting § 56.25-20 Bolting. (a) General. (1) Bolts, studs, nuts, and....01-2). (2) Bolts and studs must extend completely through the nuts. (3) See § 58.30-15(c) of this... steel stud bolts must be threaded full length or, if desired, may have reduced shanks of a diameter not...

Embodying Emotions: Making Transactions Explicit in Science Learning Contexts

ERIC Educational Resources Information Center

Milne, Catherine; Rubin, Kayla

2011-01-01

In this Forum paper we synthesize some of the main ideas from three papers: Auli Orlander and Per-Olof Wickman's ("Cult Stud Sci Educ" 6, 2011), "Bodily experiences in secondary school biology," Roger Sages' ("Cult Stud Sci Educ" 6, 2011), "About Descartes: Uses and misuses," and Steve Alsop's ("Cult Stud Sci Educ" 6, 2011), "The body bites back!"…

Structural Performance of COM-Ply Studs Made with Hardwood Veneers

Treesearch

Robert H. McAlister

1979-01-01

COM-PLY 2 x 4 studs made with veneers of yellow-poplar, sweetgum, and white oak were tested for strength and stiffness, nail-holding properties, modulus of elasticity of component parts, static bending, and compression parallel and perpendicular to the grain. All tests were conducted according to performance standards for composite studs used in exterior walls or ASTM...

Product Recovery From Hemlock "Pulpwood" From Alaska.

Treesearch

Thomas D. Fahey

1983-01-01

A total of 363 western hemlock (Tsuga heterophylla (Raf.) Sarg.) logs from Alaska were sawn to compare recovery at a stud mill and at a dimension mill. Recovery at both mills varied by log diameters and by log scaling system. Lumber grade recovery was primarily in Stud grade at the stud mill and in Standard and Construction grade at the dimension...

Common Cause Case Study: An Estimated Probability of Four Solid Rocket Booster Hold-down Post Stud Hang-ups

NASA Technical Reports Server (NTRS)

Cross, Robert

2005-01-01

Until Solid Rocket Motor ignition, the Space Shuttle is mated to the Mobil Launch Platform in part via eight (8) Solid Rocket Booster (SRB) hold-down bolts. The bolts are fractured using redundant pyrotechnics, and are designed to drop through a hold-down post on the Mobile Launch Platform before the Space Shuttle begins movement. The Space Shuttle program has experienced numerous failures where a bolt has "hung-up." That is, it did not clear the hold-down post before liftoff and was caught by the SRBs. This places an additional structural load on the vehicle that was not included in the original certification requirements. The Space Shuttle is currently being certified to withstand the loads induced by up to three (3) of eight (8) SRB hold-down post studs experiencing a "hang-up." The results af loads analyses performed for four (4) stud-hang ups indicate that the internal vehicle loads exceed current structural certification limits at several locations. To determine the risk to the vehicle from four (4) stud hang-ups, the likelihood of the scenario occurring must first be evaluated. Prior to the analysis discussed in this paper, the likelihood of occurrence had been estimated assuming that the stud hang-ups were completely independent events. That is, it was assumed that no common causes or factors existed between the individual stud hang-up events. A review of the data associated with the hang-up events, showed that a common factor (timing skew) was present. This paper summarizes a revised likelihood evaluation performed for the four (4) stud hang-ups case considering that there are common factors associated with the stud hang-ups. The results show that explicitly (i.e. not using standard common cause methodologies such as beta factor or Multiple Greek Letter modeling) taking into account the common factor of timing skew results in an increase in the estimated likelihood of four (4) stud hang-ups of an order of magnitude over the independent failure case.

Further trials of roll-feed, high-temperature dryers for 8/4 southern pine

Treesearch

P. Koch

1975-01-01

Studs cut from veneer cores and dried by four configurations of roll-feeding mechaniams (for a continuous kiln like a roll-feed veneer dryer) were compared to conventionally stickered studs. Roll-dried studs averaged leas crook (0.14 in.), bow (0.17), and twist (0.16) than those conventionally suckered (0.22, 0.26, and 0.34 inch, respectively). The data seemed to favor...

Kinetic and kinematic analysis of stamping impacts during simulated rucking in rugby union.

PubMed

Oudshoorn, Bodil Y; Driscoll, Heather F; Dunn, Marcus; James, David

2018-04-01

Laceration injuries account for up to 23% of injuries in rugby union. They are frequently caused by studded footwear as a result of a player stamping onto another player during the ruck. Little is known about the kinetics and kinematics of rugby stamping impacts; current test methods assessing laceration injury risk of stud designs therefore lack informed test parameters. In this study, twelve participants stamped on an anthropomorphic test device in a one-on-one simulated ruck setting. Velocity and inclination angle of the foot prior to impact was determined from high-speed video footage. Total stamping force and individual stud force were measured using pressure sensors. Mean foot inbound velocity was 4.3 m ∙ s -1 (range 2.1-6.3 m ∙ s -1 ). Mean peak total force was 1246 N and mean peak stud force was 214 N. The total mean effective mass during stamping was 6.6 kg (range: 1.6-13.5 kg) and stud effective mass was 1.2 kg (range: 0.5-2.9 kg). These results provide representative test parameters for mechanical test devices designed to assess laceration injury risk of studded footwear for rugby union.

System for remotely servicing a top loading captive ball valve

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berry, S.M.; Porter, M.L.

1996-06-25

An attachment for facilitating servicing of a valve is disclosed including: an assembly composed of a valve seat defining a flow path, a flow control member movable relative to the valve seat for blocking or unblocking the valve seat, and a control device including a stem coupled to the flow control member and operable for moving the flow control member relative to the valve seat; a housing for receiving the assembly, the housing having an opening via which the assembly can be removed from, and installed in, the housing, and the housing having a plurality of threaded studs which surroundmore » the opening and project away from the housing; a valve housing cover for closing and sealing the opening in the housing, the cover having a first bore for passage of the stem of the control device when the assembly is installed in the housing and a plurality of second bores each located for passage of a respective stud when the cover closes the opening in the housing. A plurality of threaded nuts are engageable with the studs for securing the cover to the housing when the cover closes the opening in the housing, wherein the attachment comprises: a plurality of nut guide devices removable from the housing and each operatively associated with a respective stud for retaining a respective nut and guiding the respective nut into alignment with the respective stud to enable the respective nut to be rotated into engagement with the respective stud; and aligning the nut guide devices with the studs. 7 figs.« less

System for remotely servicing a top loading captive ball valve

DOEpatents

Berry, S.M.; Porter, M.L.

1996-06-25

An attachment for facilitating servicing of a valve is disclosed including: an assembly composed of a valve seat defining a flow path, a flow control member movable relative to the valve seat for blocking or unblocking the valve seat, and a control device including a stem coupled to the flow control member and operable for moving the flow control member relative to the valve seat; a housing for receiving the assembly, the housing having an opening via which the assembly can be removed from, and installed in, the housing, and the housing having a plurality of threaded studs which surround the opening and project away from the housing; a valve housing cover for closing and sealing the opening in the housing, the cover having a first bore for passage of the stem of the control device when the assembly is installed in the housing and a plurality of second bores each located for passage of a respective stud when the cover closes the opening in the housing. A plurality of threaded nuts are engageable with the studs for securing the cover to the housing when the cover closes the opening in the housing, wherein the attachment comprises: a plurality of nut guide devices removable from the housing and each operatively associated with a respective stud for retaining a respective nut and guiding the respective nut into alignment with the respective stud to enable the respective nut to be rotated into engagement with the respective stud; and aligning the nut guide devices with the studs. 7 figs.

System for remotely servicing a top loading captive ball valve

DOEpatents

Berry, Stephen M.; Porter, Matthew L.

1996-01-01

An attachment for facilitating servicing of a valve, the valve including: an assembly composed of a valve seat defining a flow path, a flow control member movable relative to the valve seat for blocking or unblocking the valve seat, and a control device including a stem coupled to the flow control member and operable for moving the flow control member relative to the valve seat; a housing for receiving the assembly, the housing having an opening via which the assembly can be removed from, and installed in, the housing, and the housing having a plurality of threaded studs which surround the opening and project away from the housing; a valve housing cover for closing and sealing the opening in the housing, the cover having a first bore for passage of the stem of the control device when the assembly is installed in the housing and a plurality of second bores each located for passage of a respective stud when the cover closes the opening in the housing. A plurality of threaded nuts are engageable with the studs for securing the cover to the housing when the cover closes the opening in the housing, wherein the attachment comprises: a plurality of nut guide devices removable from the housing and each operatively associated with a respective stud for retaining a respective nut and guiding the respective nut into alignment with the respective stud to enable the respective nut to be rotated into engagement with the respective stud; and aligning the nut guide devices with the studs.

High-temperature drying of 7/4 yellow-poplar flitches for S-D-R studs

Treesearch

R. Sidney Boone; Robert R. Maeglin

1980-01-01

Yellow-poplar was dried as 7/4 flitches at high temperatures and subsequently ripped into studs to meet National Grading Rule Standards for STUD grade. The effects of growth stresses in these flitches from smaller logs appear to be minimized by this process. Dry bulb temperatures from 235° to 295° F were explored in five drying trials. Best results were by drying for...

Welding studs detection based on line structured light

NASA Astrophysics Data System (ADS)

Geng, Lei; Wang, Jia; Wang, Wen; Xiao, Zhitao

2018-01-01

The quality of welding studs is significant for installation and localization of components of car in the process of automobile general assembly. A welding stud detection method based on line structured light is proposed. Firstly, the adaptive threshold is designed to calculate the binary images. Then, the light stripes of the image are extracted after skeleton line extraction and morphological filtering. The direction vector of the main light stripe is calculated using the length of the light stripe. Finally, the gray projections along the orientation of the main light stripe and the vertical orientation of the main light stripe are computed to obtain curves of gray projection, which are used to detect the studs. Experimental results demonstrate that the error rate of proposed method is lower than 0.1%, which is applied for automobile manufacturing.

Finite element based simulation on friction stud welding of metal matrix composites to steel

NASA Astrophysics Data System (ADS)

Hynes, N. Rajesh Jesudoss; Tharmaraj, R.; Velu, P. Shenbaga; Kumar, R.

2016-05-01

Friction welding is a solid state joining technique used for joining similar and dissimilar materials with high integrity. This new technique is being successfully applied to the aerospace, automobile, and ship building industries, and is attracting more and more research interest. The quality of Friction Stud Welded joints depends on the frictional heat generated at the interface. Hence, thermal analysis on friction stud welding of stainless steel (AISI 304) and aluminium silicon carbide (AlSiC) combination is carried out in the present work. In this study, numerical simulation is carried out using ANSYS software and the temperature profiles are predicted at various increments of time. The developed numerical model is found to be adequate to predict temperature distribution of friction stud weld aluminium silicon carbide/stainless steel joints.

Test evaluation of a laminated wood wind turbine blade concept

NASA Technical Reports Server (NTRS)

Faddoul, J. R.

1981-01-01

A series of tests conducted on a root end section of a laminated wood wind turbine blade are reported. The blade to hub transition of the wood blade uses steel studs cast into the wood D spar with a filled epoxy. Both individual studs and a full scale, short length, root section were tested. Results indicate that the bonded stud concept is more than adequate for both the 30 year life fatigue loads and for the high wind or hurricane gust loads.

Common Cause Case Study: An Estimated Probability of Four Solid Rocket Booster Hold-Down Post Stud Hang-ups

NASA Technical Reports Server (NTRS)

Cross, Robert

2005-01-01

Until Solid Rocket Motor ignition, the Space Shuttle is mated to the Mobil Launch Platform in part via eight (8) Solid Rocket Booster (SRB) hold-down bolts. The bolts are fractured using redundant pyrotechnics, and are designed to drop through a hold-down post on the Mobile Launch Platform before the Space Shuttle begins movement. The Space Shuttle program has experienced numerous failures where a bolt has hung up. That is, it did not clear the hold-down post before liftoff and was caught by the SRBs. This places an additional structural load on the vehicle that was not included in the original certification requirements. The Space Shuttle is currently being certified to withstand the loads induced by up to three (3) of eight (8) SRB hold-down experiencing a "hang-up". The results of loads analyses performed for (4) stud hang-ups indicate that the internal vehicle loads exceed current structural certification limits at several locations. To determine the risk to the vehicle from four (4) stud hang-ups, the likelihood of the scenario occurring must first be evaluated. Prior to the analysis discussed in this paper, the likelihood of occurrence had been estimated assuming that the stud hang-ups were completely independent events. That is, it was assumed that no common causes or factors existed between the individual stud hang-up events. A review of the data associated with the hang-up events, showed that a common factor (timing skew) was present. This paper summarizes a revised likelihood evaluation performed for the four (4) stud hang-ups case considering that there are common factors associated with the stud hang-ups. The results show that explicitly (i.e. not using standard common cause methodologies such as beta factor or Multiple Greek Letter modeling) taking into account the common factor of timing skew results in an increase in the estimated likelihood of four (4) stud hang-ups of an order of magnitude over the independent failure case.

Precise Restraightening of Bent Studs

NASA Technical Reports Server (NTRS)

Boardman, R. E.

1982-01-01

Special tool quickly bends studs back into shape accurately and safely by force applied by hydraulic ram, with deflection being measured by dial indicator. Ram and indicator can be interchanged for straightening in reverse direction.

Modelling road dust emission abatement measures using the NORTRIP model: Vehicle speed and studded tyre reduction

NASA Astrophysics Data System (ADS)

Norman, M.; Sundvor, I.; Denby, B. R.; Johansson, C.; Gustafsson, M.; Blomqvist, G.; Janhäll, S.

2016-06-01

Road dust emissions in Nordic countries still remain a significant contributor to PM10 concentrations mainly due to the use of studded tyres. A number of measures have been introduced in these countries in order to reduce road dust emissions. These include speed reductions, reductions in studded tyre use, dust binding and road cleaning. Implementation of such measures can be costly and some confidence in the impact of the measures is required to weigh the costs against the benefits. Modelling tools are thus required that can predict the impact of these measures. In this paper the NORTRIP road dust emission model is used to simulate real world abatement measures that have been carried out in Oslo and Stockholm. In Oslo both vehicle speed and studded tyre share reductions occurred over a period from 2004 to 2006 on a major arterial road, RV4. In Stockholm a studded tyre ban on Hornsgatan in 2010 saw a significant reduction in studded tyre share together with a reduction in traffic volume. The model is found to correctly simulate the impact of these measures on the PM10 concentrations when compared to available kerbside measurement data. Importantly meteorology can have a significant impact on the concentrations through both surface and dispersion conditions. The first year after the implementation of the speed reduction on RV4 was much drier than the previous year, resulting in higher mean concentrations than expected. The following year was much wetter with significant rain and snow fall leading to wet or frozen road surfaces for 83% of the four month study period. This significantly reduced the net PM10 concentrations, by 58%, compared to the expected values if meteorological conditions had been similar to the previous years. In the years following the studded tyre ban on Hornsgatan road wear production through studded tyres decreased by 72%, due to a combination of reduced traffic volume and reduced studded tyre share. However, after accounting for exhaust contributions and the impact of meteorological conditions in the model calculations then the net mean reduction in PM10 concentrations was only ∼50%, in agreement with observations. The NORTRIP model is shown to be able to reproduce the impacts of both traffic measures and meteorology on traffic induced PM10 concentrations, making it a unique and valuable tool for predicting the impact of measures for air quality management applications.

Device for measuring hole elongation in a bolted joint

NASA Technical Reports Server (NTRS)

Wichorek, Gregory R. (Inventor)

1987-01-01

A device to determine the operable failure mode of mechanically fastened lightweight composite joints by measuring the hole elongation of a bolted joint is disclosed. The double-lap joint test apparatus comprises a stud, a test specimen having a hole, two load transfer plates, and linear displacement measuring instruments. The test specimen is sandwiched between the two load transfer plates and clamped together with the stud. Spacer washers are placed between the test specimen and each load transfer plate to provide a known, controllable area for the determination of clamping forces around the hole of the specimen attributable to bolt torque. The spacer washers also provide a gap for the mounting of reference angles on each side of the test specimen. Under tensile loading, elongation of the hole of the test specimen causes the stud to move away from the reference angles. This displacement is measured by the voltage output of two linear displacement measuring instruments that are attached to the stud and remain in contact with the reference angles throughout the tensile loading. The present invention obviates previous problems in obtaining specimen deformation measurements by monitoring the reference angles to the test specimen and the linear displacement measuring instruments to the stud.

Economic Analysis of Understanding and Implementing Design Criteria for Acoustic Suppression in Military Residential Units

DTIC Science & Technology

1991-06-01

ASTM to provide a single number rating system for insulation of common building materials, compound structures, doors, windows, ect. It is also...illustrate this, Figure (4) shows a cost relationship of providing noise suppression in walls. The walls are made of 2 X 4 wood studs, drywall and fibrous...INSULATION, 2 LAYERS 1/2" DRYWALL BOTH SIDES STC 55 TWO ROWS WOOD STUDS, 6" FIBROUS INSULATION, 1 LAYER 1/2" DRYWALL BOTH SIDES STC 50 2 X 4 STUDS, 3 1/2

Economic feasibility of manufacturing COM-PLY studs in the South

Treesearch

Gerald A. Koenigshof

1978-01-01

The investment and production cost required to manufacture COM-PLY studs in the South are presented. It is possible to obtain a 20 percent or greater internal rate of return on an investment in manufacturing COM-PLY.

Micro-deval coarse aggregate test evaluation

DOT National Transportation Integrated Search

2001-05-01

Studded tire use in Oregon results in millions of dollars of pavement damage annually. Accurate tests are needed to qualify durable aggregate for pavements to resist studded tire damage. ODOT currently uses the Los Angeles abrasion test as one of the...

Micro-Deval coarse aggregate test evaluation : final report.

DOT National Transportation Integrated Search

2001-05-01

Studded tire use in Oregon results in millions of dollars of pavement damage annually. Accurate tests are needed to qualify durable aggregate for pavements to resist studded tire damage. ODOT currently uses the Los Angeles abrasion test as one of the...

Research notes : studded tire damage repair : the first year.

DOT National Transportation Integrated Search

1998-02-01

The Oregon Department of Transportation has monitored rutting caused by studded tires since 1974. In the past decade, the damage has increased rapidly. The overlay was divided into four sections. Each section received a different type of thin asphalt...

Effects of studded tires on roadside airborne dust pollution in Niigata, Japan

NASA Astrophysics Data System (ADS)

Fukuzaki, Norio; Yanaka, Takaaki; Urushiyama, Yoshio

Two series of dust samples, collected by Andersen impactors (denoted by AN) and low-volume air samplers (denoted by LV), were investigated with respect to roadside airborne dusts collected in two different periods in 1983. These were the periods (i) with studded tires (February and March) and (ii) without studded tires (October). Multi-element determinations of these samples were made by neutron activation analysis and atomic absorption spectrometry. The total concentration of AN in roadside air for period (i) was about three times higher than for the period without studded tires. The lithophilic elements such as Na, Al, K, Ca, Ti, Fe and Th, and component-metal elements of stud tip, W and Ta, produced a significant increase in atmospheric concentration in winter. The contribution of pavement material, one of the most interesting components of airborne particles in this study, was related to total AN and LV by the chemical element balance method. It made up only 16 percent (9.1 μgm -3) of AN in October, compared with 46 percent (70.2 μgm -3) in February. It was also observed that the atmospheric concentrations of pavement debris to total LV decreased with the distance from the road to each sampling site.

[Energy intake and body weight development of Warmblood foals that changed stud at weaning].

PubMed

Mack, J K; Remler, H P; Senckenberg, E; Kienzle, E

2014-01-01

This study investigated the energy requirements of Warmblood foals with a change of the stud at weaning. Nine colts purchased at weaning participated in the study aged approximately 6 months to 1 year. They were transported to the stud by their breeders either having been separated from their dams in their home stable or upon arrival at the stud. The foals were offered a late first cut of haylage, oats and foal starter feed. To ensure individual feeding of concentrates, the foals were tethered twice daily. The total combined haylage intake of all foals per day was recorded. Individual concentrate intake, body weight and body condition score (BCS) were documented at 4-week intervals. The total energy intake was 74 MJ digestible energy (68 MJ metabolisable energy) per animal per day. The foals had been delivered at the stud with a comparably low body weight (285 ± 30 kg) and BCS (4.2 ± 0.4 on a scale from 1 to 9). At the end of the study, aged 319 ± 22 days, they attained an average body weight of 326 ± 24 kg and a BCS of 4.2 ± 0.4. The energy intake of the foals of this study was higher and their body weight development slower than in foals of a parallel study, which were born and raised in the stud and therefore exposed to less stressful weaning conditions. Foals with a comparatively low body weight and BCS at weaning in combination with further stressors need considerably more energy than foals that undergo less stressful weaning conditions.

Development of an advanced high-temperature fastener system for advanced aerospace vehicle application

NASA Technical Reports Server (NTRS)

Kull, F. R.

1975-01-01

The results of a program to develop a lightweight high temperature reusable fastening system for aerospace vehicle thermal protection system applications are documented. This feasibility program resulted in several fastener innovations which will meet the specific needs of the heat shield application. Three systems were designed from Hayes 188 alloy and tested by environmental exposure and residual mechanical properties. The designs include a clinch stud with a collar retainer, a weld stud with a split ring retainer, and a caged stud with a collar retainer. The results indicated that a lightweight, reusable, high temperature fastening system can be developed for aerospace vehicle application.

Method of joining metallic and composite components

NASA Technical Reports Server (NTRS)

Semmes, Edmund B. (Inventor)

2010-01-01

A method is provided for joining a metallic member to a structure made of a composite matrix material. One or more surfaces of a portion of the metallic member that is to be joined to the composite matrix structure is provided with a plurality of outwardly projecting studs. The surface including the studs is brought into engagement with a portion of an uncured composite matrix material so that fibers of the composite matrix material intertwine with the studs, and the metallic member and composite structure form an assembly. The assembly is then companion cured so as to join the metallic member to the composite matrix material structure.

The use and effects of studded tires in Oregon.

DOT National Transportation Integrated Search

1974-12-01

During the past 11 years the use of studded tires has increased from a novelty to anestimated average of 20 percent for the Northern States in which snow and ice is expected. An alarming amount of surface wear in the wheel paths of the highway paveme...

Determination of remaining fatigue life of welded stud details on overhead aluminum sign panels in Virginia.

DOT National Transportation Integrated Search

2005-01-01

Some overhead highways signs in Virginia using a specific welded threaded stud and clip connection have failed while in service. From inspection of the signs it was determined that the failure was caused by fatigue of the weld connecting the threaded...

49 CFR 231.17 - Specifications common to all steam locomotives.

Code of Federal Regulations, 2011 CFR

2011-10-01

... shall be securely fastened with bolts, rivets, or studs. (ii) Locomotives having Wootten type boilers... inches above outside edge of running boards, securely fastened with bolts, rivets, or studs. (c... inches in height, measured from the top of end sill, and securely fastened with bolts or rivets. (f...

Studded tire wear on Portland cement concrete pavement in the Washington State Department of Transportation route network.

DOT National Transportation Integrated Search

2010-06-01

Studded tires are legal in Washington State and are typically allowed to be used each winter between the months of November and April. They are known to cause accelerated wheelpath wear resulting in additional pavement preservation costs. While studd...

One-day kilning dries pine studs to 10% moisture

Treesearch

P. Koch

1971-01-01

USDA Southern Forest Experiment Station tested drying southern pine studs in air cross-circulated at velocity of 930 fpm and temperature of 240°F; wet-bulb depression was 80°F. Under same regime, 1" boards dried in 1 0 hours, plus time to condition.

Studs and protest-hypermasculinity: the tomboyism within black lesbian female masculinity.

PubMed

Lane-Steele, Laura

2011-01-01

In this article, I use the ethnographic work I conducted in the summer of 2009 with Black lesbian women from South Carolina to show how Black female masculinity has been influenced by historically based constructions of Black gender. I will argue that these studs strategically construct and perform their masculinity in ways that shield them from sexism, racism, and homophobia both in and out of their Black community. By adopting the particular type of masculinity common among their Black male peers, these studs can gain access to some levels of male privilege and power which, in turn, can act as useful defense mechanisms against multiple types of discrimination and oppression.

Measure Guideline: Deep Energy Enclosure Retrofit for Double-Stud Walls

DOE Office of Scientific and Technical Information (OSTI.GOV)

Loomis, H.; Pettit, B.

2015-06-22

This Measure Guideline describes a deep energy enclosure retrofit solution that provides insulation to the interior of the wall assembly with the use of a double-stud wall. The guide describes two approaches to retrofitting the existing walls—one that involves replacing the existing cladding and the other that leaves the cladding in place. This guideline also covers the design principles related to the use of various insulation types and provides strategies and procedures for implementing the double-stud wall retrofit. It also includes an evaluation of important moisture-related and indoor air quality measures that need to be implemented to achieve a durablemore » high-performance wall.« less

Measure Guideline: Deep Energy Enclosure Retrofit for Double-Stud Walls

DOE Office of Scientific and Technical Information (OSTI.GOV)

Loomis, H.; Pettit, B.

2015-06-01

This Measure Guideline describes a deep energy enclosure retrofit (DEER) solution that provides insulation to the interior of the wall assembly with the use of a double stud wall. The guide describes two approaches to retrofitting the existing the walls: one involving replacement of the existing cladding, and the other that leaves the existing cladding in place. It discusses the design principles related to the use of various insulation types, and provides strategies and procedures for implementing the double stud wall retrofit. It also evaluates important moisture-related and indoor air quality measures that need to be implemented to achieve amore » durable, high performance wall.« less

Non-intrusive Shock Measurements Using Laser Doppler Vibrometers

NASA Technical Reports Server (NTRS)

Statham, Shannon M.; Kolaini, Ali R.

2012-01-01

Stud mount accelerometers are widely used by the aerospace industry to measure shock environments during hardware qualification. The commonly used contact-based sensors, however, interfere with the shock waves and distort the acquired signature, which is a concern not actively discussed in the community. To alleviate these interference issues, engineers at the Jet Propulsion Laboratory are investigating the use of non-intrusive sensors, specifically Laser Doppler Vibrometers, as alternatives to the stud mounted accelerometers. This paper will describe shock simulation tests completed at the Jet Propulsion Laboratory, compare the measurements from stud mounted accelerometers and Laser Doppler Vibrometers, and discuss the advantages and disadvantages of introducing Laser Doppler Vibrometers as alternative sensors for measuring shock environments.

Effects of commercial selenium products on glutathione peroxidase activity and semen quality in stud boars

USDA-ARS?s Scientific Manuscript database

The aim of this study was to determine how dietary supplementation of inorganic and organic selenium affects selenium concentration and glutathione peroxidase activity in blood and sperm of sexually mature stud boars. Twenty-four boars of the Large White, Landrace, Pietrain, and Duroc breeds of opt...

The Meaning of Work: Studs Terkel's Working as a Teaching Tool

ERIC Educational Resources Information Center

Cox, Pamela L.

2004-01-01

Studs Terkel explores the motivation to work in his classic book "Working," compiling more than 100 interviews of workers across America. The author has found "Working" to be a useful vehicle for exploring organizational issues and for confronting students with the realities of the workplace. Terkel's interviews are honest, earthy, seasoned with…

24 CFR 3280.808 - Wiring methods and materials.

Code of Federal Regulations, 2010 CFR

2010-04-01

... frames where the cable or armor would be less than 11/2 inches from the inside or outside surface of the studs when the wall covering materials are in contact with the studs. Steel plates on each side of the... used when closely routed against frames, and equipment enclosures. (l) The cables or conductors shall...

Simplified failure sequence evaluation of reactor pressure vessel head corroding in-core instrumentation assembly

DOE Office of Scientific and Technical Information (OSTI.GOV)

McVicker, J.P.; Conner, J.T.; Hasrouni, P.N.

1995-11-01

In-Core Instrumentation (ICI) assemblies located on a Reactor Pressure Vessel Head have a history of boric acid leakage. The acid tends to corrode the nuts and studs which fasten the flanges of the assembly, thereby compromising the assembly`s structural integrity. This paper provides a simplified practical approach in determining the likelihood of an undetected progressing assembly stud deterioration, which would lead to a catastrophic loss of reactor coolant. The structural behavior of the In-Core Instrumentation flanged assembly is modeled using an elastic composite section assumption, with the studs transmitting tension and the pressure sealing gasket experiencing compression. Using the abovemore » technique, one can calculate the flange relative deflection and the consequential coolant loss flow rate, as well as the stress in any stud. A solved real life example develops the expected failure sequence and discusses the exigency of leak detection for safe shutdown. In the particular case of Calvert Cliffs Nuclear Power Plant (CCNPP) it is concluded that leak detection occurs before catastrophic failure of the ICI flange assembly.« less

Methods of Optimal Control of Laser-Plasma Instabilities Using Spike Trains of Uneven Duration and Delay (STUD Pulses)

NASA Astrophysics Data System (ADS)

Afeyan, Bedros

2013-10-01

We have recently introduced and extensively studied a new adaptive method of LPI control. It promises to extend the effectiveness of laser as inertial fusion drivers by allowing active control of stimulated Raman and Brillouin scattering and crossed beam energy transfer. It breaks multi-nanosecond pulses into a series of picosecond (ps) time scale spikes with comparable gaps in between. The height and width of each spike as well as their separations are optimization parameters. In addition, the spatial speckle patterns are changed after a number of successive spikes as needed (from every spike to never). The combination of these parameters allows the taming of parametric instabilities to conform to any desired reduced reflectivity profile, within the bounds of the performance limitations of the lasers. Instead of pulse shaping on hydrodynamical time scales, far faster (from 1 ps to 10 ps) modulations of the laser profile will be needed to implement the STUD pulse program for full LPI control. We will show theoretical and computational evidence for the effectiveness of the STUD pulse program to control LPI. The physics of why STUD pulses work and how optimization can be implemented efficiently using statistical nonlinear optical models and techniques will be explained. We will also discuss a novel diagnostic system employing STUD pulses that will allow the boosted measurement of velocity distribution function slopes on a ps time scale in the small crossing volume of a pump and a probe beam. Various regimes from weak to strong coupling and weak to strong damping will be treated. Novel pulse modulation schemes and diagnostic tools based on time-lenses used in both microscope and telescope modes will be suggested for the execution of the STUD pule program. Work Supported by the DOE NNSA-OFES Joint Program on HEDLP and DOE OFES SBIR Phase I Grants.

Reproductive performance of Thoroughbred mares in the Waikato region of New Zealand: 2. Multivariable analyses and sources of variation at the mare, stallion and stud farm level.

PubMed

Hanlon, D W; Stevenson, M; Evans, M J; Firth, E C

2012-11-01

The objective of this study was to utilise multivariable statistical methods appropriate for clustered data to identify mare-related explanatory variables that significantly affected the reproductive performance of Thoroughbred mares in the Waikato region of New Zealand. In addition, we aimed to determine the relative contribution of the mare, stallion and stud farm to reproductive performance. A prospective cohort study was performed involving five stud farms in the Waikato region of New Zealand during three consecutive breeding seasons (2006-2008). A total of 1,482 individual mares contributed 2007 mare years and 3,402 oestrous cycles over the three breeding seasons. Reproductive performance was measured using three parameters; (a) first-cycle pregnancy rate (FCPR), (b) end-of-season pregnancy rate (SPR), and (c) the start-of-mating to conception interval. When controlled for the effects of serving stallion, stud farm and year of study the only significant mare-related variables included in the final models of FCPR, SPR and conception interval were the age of the mare and her reproductive status (classified as dry or foaling). Advancing mare age significantly reduced reproductive performance regardless of reproductive status and foaling mares had significantly poorer reproductive outcomes compared with dry mares when controlled for age. For each additional increase in year of age, the FCPR was reduced by a factor of 0.94 (95% CI=0.92-0.96) and the SPR was reduced by a factor of 0.91 (95% CI=0.88-0.93). Mares older than 14 years of age took longer to conceive after the start-of-mating compared with younger mares. The daily hazard of conception for mares 14 years and older was 0.64 (95% CI=0.47-0.83) times less than mares younger than 9 years of age. Determining the relative contribution of the mare, stallion and stud farm to the FCPR indicated that 95.9% of the variation was at the mare level, 4.1% was at the stallion level and 0% was at the stud farm level. For the SPR the variance components indicated that 92.5% of the variation was at the mare level, 6.7% was at the stallion level and 0.8% was at the stud farm level. The reproductive performance of Thoroughbred mares in the Waikato region of New Zealand is influenced by two main mare-related factors; the age of the mare and her reproductive status (dry or foaling). The majority of variation in reproductive performance was associated with mare-level factors and the contribution of the stallion and stud farm was relatively minor.

Changes in United States Advertising 1976-1986 (a la Studs Terkel).

ERIC Educational Resources Information Center

Jackson, DeForrest; Lamb, Christopher J.

To examine the most important changes in marketing and advertising of the decade from 1976 to 1986, more than 100 people were interviewed, and their responses were fashioned into an oral history modeled on the technique used in Studs Terkel's popular books. Among those interviewed were advertising and marketing professionals, as well as casual…

An Induction Heating Method with Traveling Magnetic Field for Long Structure Metal

NASA Astrophysics Data System (ADS)

Sekine, Takamitsu; Tomita, Hideo; Obata, Shuji; Saito, Yukio

A novel dismantlable adhesion method for recycling operation of interior materials is proposed. This method is applied a high frequency induction heating and a thermoplastic adhesive. For an adhesion of interior material to long steel stud, a conventional spiral coil as like IH cooking heater gives inadequateness for uniform heating to the stud. Therefore, we have proposed an induction heating method with traveling magnetic field for perfect long structures bonding. In this paper, we describe on the new adhesion method using the 20kHz, three-phase 200V inverter and linear induction coil. From induction heating characteristics to thin steel plates and long studs, the method is cleared the usefulness for uniform heating to long structures.

Breeding racehorses: what price good genes?

PubMed

Wilson, Alastair J; Rambaut, Andrew

2008-04-23

Horse racing is a multi-million pound industry, in which genetic information is increasingly used to optimize breeding programmes. To maximize the probability of producing a successful offspring, the owner of a mare should mate her with a high-quality stallion. However, stallions with big reputations command higher stud fees and paying these is only a sensible strategy if, (i) there is a genetic variation for success on the racecourse and (ii) stud fees are an honest signal of a stallion's genetic quality. Using data on thoroughbred racehorses, and lifetime earnings from prize money (LE) as a measure of success, we performed quantitative genetic analyses within an animal model framework to test these two conditions. Although LE is heritable (VA=0.299+/-0.108, Pr=0.002), there is no genetic variance for stud fee and the genetic correlation between traits is therefore zero. This result is supported by an absence of any relationship between stud fees for currently active stallions and the predicted LE for their (hypothetical) offspring. Thus, while there are good genes to be bought, a stallion's fees are not an honest signal of his genetic quality and are a poor predictor of a foal's prize winning potential.

Roll forming of eco-friendly stud

NASA Astrophysics Data System (ADS)

Keum, Y. T.; Lee, S. Y.; Lee, T. H.; Sim, J. K.

2013-12-01

In order to manufacture an eco-friendly stud, the sheared pattern is designed by the Taguchi method and expanded by the side rolls. The seven geometrical shape of sheared pattern are considered in the structural and thermal analyses to select the best functional one in terms of the durability and fire resistance of dry wall. For optimizing the size of the sheared pattern chosen, the L9 orthogonal array and smaller-the-better characteristics of the Taguchi method are used. As the roll gap causes forming defects when the upper-and-lower roll type is adopted for expanding the sheared pattern, the side roll type is introduced. The stress and strain distributions obtained by the FEM simulation of roll-forming processes are utilized for the design of expanding process. The expanding process by side rolls shortens the length of expanding process and minimizes the cost of dies. Furthermore, the stud manufactured by expanding the sheared pattern of the web is an eco-friend because of the scrapless roll-forming process. In addition, compared to the conventionally roll-formed stud, the material cost is lessened about 13.6% and the weight is lightened about 15.5%.

Improved stud configurations for attaching laminated wood wind turbine blades

NASA Technical Reports Server (NTRS)

Fadoul, J. R.

1985-01-01

A series of bonded stud design configurations was screened on the basis of tension-tension cyclic tests to determine the structural capability of each configuration for joining a laminated wood structure (wind turbine blade) to a steel flange (wind turbine hub). Design parameters which affected the joint strength (ultimate and fatigue) were systematically varied and evaluated through appropriate testing. Two designs showing the most promise were used to fabricate addiate testing. Two designs showing the most promise were used to fabricate additional test specimens to determine ultimate strength and fatigue curves. Test results for the bonded stud designs demonstrated that joint strengths approaching the 10,000 to 12,000 psi ultimate strength and 5000 psi high cycle fatigue strength of the wood epoxy composite could be achieved.

The influence of finite cavities on the sound insulation of double-plate structures.

PubMed

Brunskog, Jonas

2005-06-01

Lightweight walls are often designed as frameworks of studs with plates on each side--a double-plate structure. The studs constitute boundaries for the cavities, thereby both affecting the sound transmission directly by short-circuiting the plates, and indirectly by disturbing the sound field between the plates. The paper presents a deterministic prediction model for airborne sound insulation including both effects of the studs. A spatial transform technique is used, taking advantage of the periodicity. The acoustic field inside the cavities is expanded by means of cosine-series. The transmission coefficient (angle-dependent and diffuse) and transmission loss are studied. Numerical examples are presented and comparisons with measurement are performed. The result indicates that a reasonably good agreement between theory and measurement can be achieved.

Investigation of Accelerated Life Prediction Techniques

DTIC Science & Technology

1975-10-01

26, No. 1, 1974, ;). 13. 116. Krukar, M., et al, STUDDED TIRE PAVEMENT WEAR REDUCTION AND REPAIR, Washington State Dept. of Highways, Highway...167. Okushlma, K., and Kakino, Y., STUD * ON INFLUENCE OF GROOVE WEAR OF A TOOL TO SURFACE ROUGHNESS DURING FINISHING TURNING OF CARBON STEEL, Journal...MODIFICATION OF ASPHALT CEMENTS FOR IMPROVE- MENT OF WEAR RESISTANCE OF PAVEMENT SURFACES, Materials Research «nd Development, Inc., Oakland

Reduction of Biomechanical and Welding Fume Exposures in Stud Welding.

PubMed

Fethke, Nathan B; Peters, Thomas M; Leonard, Stephanie; Metwali, Mahmoud; Mudunkotuwa, Imali A

2016-04-01

The welding of shear stud connectors to structural steel in construction requires a prolonged stooped posture that exposes ironworkers to biomechanical and welding fume hazards. In this study, biomechanical and welding fume exposures during stud welding using conventional methods were compared to exposures associated with use of a prototype system that allowed participants to weld from an upright position. The effect of base material (i.e. bare structural beam versus galvanized decking) on welding fume concentration (particle number and mass), particle size distribution, and particle composition was also explored. Thirty participants completed a series of stud welding simulations in a local apprenticeship training facility. Use of the upright system was associated with substantial reductions in trunk inclination and the activity levels of several muscle groups. Inhalable mass concentrations of welding fume (averaged over ~18 min) when using conventional methods were high (18.2 mg m(-3) for bare beam; 65.7 mg m(-3) for through deck), with estimated mass concentrations of iron (7.8 mg m(-3) for bare beam; 15.8 mg m(-3) for through deck), zinc (0.2 mg m(-3) for bare beam; 15.8 mg m(-3) for through deck), and manganese (0.9 mg m(-3) for bare beam; 1.5 mg m(-3) for through deck) often exceeding the American Conference of Governmental Industrial Hygienists Threshold Limit Values (TLVs). Number and mass concentrations were substantially reduced when using the upright system, although the total inhalable mass concentration remained above the TLV when welding through decking. The average diameters of the welding fume particles for both bare beam (31±17 nm) through deck conditions (34±34 nm) and the chemical composition of the particles indicated the presence of metallic nanoparticles. Stud welding exposes ironworkers to potentially high levels of biomechanical loading (primarily to the low back) and welding fume. The upright system used in this study improved exposure levels during stud welding simulations, but further development is needed before field deployment is possible. © The Author 2015. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

Reduction of Biomechanical and Welding Fume Exposures in Stud Welding

PubMed Central

Fethke, Nathan B.; Peters, Thomas M.; Leonard, Stephanie; Metwali, Mahmoud; Mudunkotuwa, Imali A.

2016-01-01

The welding of shear stud connectors to structural steel in construction requires a prolonged stooped posture that exposes ironworkers to biomechanical and welding fume hazards. In this study, biomechanical and welding fume exposures during stud welding using conventional methods were compared to exposures associated with use of a prototype system that allowed participants to weld from an upright position. The effect of base material (i.e. bare structural beam versus galvanized decking) on welding fume concentration (particle number and mass), particle size distribution, and particle composition was also explored. Thirty participants completed a series of stud welding simulations in a local apprenticeship training facility. Use of the upright system was associated with substantial reductions in trunk inclination and the activity levels of several muscle groups. Inhalable mass concentrations of welding fume (averaged over ~18min) when using conventional methods were high (18.2mg m−3 for bare beam; 65.7mg m−3 for through deck), with estimated mass concentrations of iron (7.8mg m−3 for bare beam; 15.8mg m−3 for through deck), zinc (0.2mg m−3 for bare beam; 15.8mg m−3 for through deck), and manganese (0.9mg m−3 for bare beam; 1.5mg m−3 for through deck) often exceeding the American Conference of Governmental Industrial Hygienists Threshold Limit Values (TLVs). Number and mass concentrations were substantially reduced when using the upright system, although the total inhalable mass concentration remained above the TLV when welding through decking. The average diameters of the welding fume particles for both bare beam (31±17nm) through deck conditions (34±34nm) and the chemical composition of the particles indicated the presence of metallic nanoparticles. Stud welding exposes ironworkers to potentially high levels of biomechanical loading (primarily to the low back) and welding fume. The upright system used in this study improved exposure levels during stud welding simulations, but further development is needed before field deployment is possible. PMID:26602453

Analysis of hygienic critical control points in boar semen production.

PubMed

Schulze, M; Ammon, C; Rüdiger, K; Jung, M; Grobbel, M

2015-02-01

The present study addresses the microbiological results of a quality control audit in artificial insemination (AI) boar studs in Germany and Austria. The raw and processed semen of 344 boars in 24 AI boar studs were analyzed. Bacteria were found in 26% (88 of 344) of the extended ejaculates and 66.7% (18 of 24) of the boar studs. The bacterial species found in the AI dose were not cultured from the respective raw semen in 95.5% (84 of 88) of the positive samples. These data, together with the fact that in most cases all the samples from one stud were contaminated with identical bacteria (species and resistance profile), indicate contamination during processing. Microbiological investigations of the equipment and the laboratory environment during semen processing in 21 AI boar studs revealed nine hygienic critical control points (HCCP), which were addressed after the first audit. On the basis of the analysis of the contamination rates of the ejaculate samples, improvements in the hygiene status were already present in the second audit (P = 0.0343, F-test). Significant differences were observed for heating cabinets (improvement, P = 0.0388) and manual operating elements (improvement, P = 0.0002). The odds ratio of finding contaminated ejaculates in the first and second audit was 1.68 (with the 95% confidence interval ranging from 1.04 to 2.69). Furthermore, an overall good hygienic status was shown for extenders, the inner face of dilution tank lids, dyes, and ultrapure water treatment plants. Among the nine HCCP considered, the most heavily contaminated samples, as assessed by the median scores throughout all the studs, were found in the sinks and/or drains. High numbers (>10(3) colony-forming units/cm(2)) of bacteria were found in the heating cabinets, ejaculate transfer, manual operating elements, and laboratory surfaces. In conclusion, the present study emphasizes the need for both training of the laboratory staff in monitoring HCCP in routine semen production and audits in such AI centers for the external control of hygiene parameters. Copyright © 2015 Elsevier Inc. All rights reserved.

Development of Lead Free Energy Absorber for Space Shuttle Blast Container

NASA Technical Reports Server (NTRS)

Balles, Donald; Ingram, Thomas; Novak, Howard; Schricker, Albert

1998-01-01

The Space Shuttle is connected to the mobile launch platform (MLP) by four aft skirt hold down studs on each solid rocket booster (SRB). Prior to lift-off, the frangible nuts inside the aft skirt blast containers are severed into two nut halves by two pyrotechnic booster cartridges. This action releases the Space Shuttle and allows the hold down studs to eject through the aft skirt bore and then down into the MLP. USBI has been tasked to upgrade the blast container for two specific reasons: (1) To eliminate lead for environmental concerns, and (2) To reduce the chance of nut recontact with the holddown stud. Nut recontact with the stud has been identified as a likely contributor to stud hang-ups. This upgrade will replace the lead liner with a unique open cell aluminum foam material, that has commercial and military uses. The aluminum foam used as an energy absorber is a proven design in many other aerospace/defense applications. Additional benefits of using the open cell, energy absorbent aluminum foam in place of the solid lead liner are: (A) Lead handling/exposure and possible contamination, along with hazardous waste disposal, will be eliminated; (B) Approximately 200 lbs. weight savings will be contributed to each Space Shuttle flight by using aluminum foam instead of lead; (C) The new aluminum liner is designed to catch all shrapnel from frangible nuts, thus virtually eliminating chance of debris exiting the HDP and causing potential damage to the vehicle; and (D) Using the lighter aluminum liner instead of lead, allows for easier assembly and disassembly of blast container elements, which also improves safety, operator handling, and the efficiency of operations.

Development of Lead Free Energy Absorber for Space Shuttle Blast Container

NASA Technical Reports Server (NTRS)

Balles, Donald; Ingram, Thomas; Novak, Howard; Schricker, Albert

1999-01-01

The Space Shuttle is connected to the mobile launch platform (MLP) by four aft skirt hold down studs on each solid rocket booster (SRB). Prior to lift-off, the frangible nuts inside the aft skirt blast containers are severed into two nut halves by two pyrotechnic booster cartridges. This action releases the Space Shuttle and allows the hold down studs to eject through the aft skirt bore and then down into the MLP. USBI has been tasked to upgrade the blast container for two specific reasons: (1) To eliminate lead for environmental concerns, and (2) To reduce the chance of nut recontact with the holddown stud. Nut recontact with the stud has been identified as a likely contributor to stud hang-ups. This upgrade will replace the lead liner with a unique open cell aluminum foam material, that has commercial and military uses. The aluminum foam used as an energy absorber is a proven design in many other aerospace/defense applications. Additional benefits of using the open cell, energy absorbent aluminum foam in place of the solid lead liner are: (1) Lead handling / exposure and possible contamination, along with hazardous waste disposal, will be eliminated; (2) Approximately 200 lbs. weight savings will be contributed to each Space Shuttle flight by using aluminum foam instead of lead; (3) The new aluminum liner is designed to catch all shrapnel from frangible nuts, thus virtually eliminating chance of debris exiting the HDP and causing potential damage to the vehicle; (4) Using the lighter aluminum liner instead of lead, allows for easier assembly and disassembly of blast container elements, which also improves safety, operator handling, and the efficiency of operations.

Risk assessment of the introduction of porcine reproductive and respiratory syndrome virus via boar semen into Switzerland as an example of a PRRSV-free country.

PubMed

Nathues, C; Zimmerli, U; Hauser, R; Nathues, H; Grosse Beilage, E; Schüpbach-Regula, G

2014-12-01

Switzerland is currently porcine reproductive and respiratory syndrome virus (PRRSV) free, but semen imports from PRRSV-infected European countries are increasing. As the virus can be transmitted via semen, for example, when a free boar stud becomes infected, and the risk of its import in terms of PRRSV introduction is unknown, the annual probability to accidentally import the virus into Switzerland was estimated in a risk assessment. A quantitative stochastic model was set up with data comprised by import figures of 2010, interviews with boar stud owners and expert opinion. It resulted in an annual median number of 0.18 imported ejaculates (= imported semen doses from one collection from one donor) from PRRSV-infected boars. Hence, one infected ejaculate would be imported every 6 years and infect a mean of 10 sows. These results suggest that under current circumstances, there is a substantial risk of PRRSV introduction into Switzerland via imported boar semen and that measures to enhance safety of imports should be taken. The time from infection of a previously negative boar stud to its detection had the highest impact on the number of imported 'positive' ejaculates. Therefore, emphasis should be placed on PRRSV monitoring protocols in boar studs. Results indicated that a substantial increase in safety could only be achieved with much tighter sampling protocols than currently performed. Generally, the model could easily be customized for other applications like other countries or regions or even sow farms that want to estimate their risk when purchasing semen from a particular boar stud. © 2013 Blackwell Verlag GmbH.

Devil in the Details: A Critical Review of "Theoretical Loss".

PubMed

Tom, Matthew A; Shaffer, Howard J

2016-09-01

In their review of Internet gambling studies, Auer and Griffiths (J Gambl Stud 30(4), 879-887, 2014) question the validity of using bet size as an indicator of gambling intensity. Instead, in that review and in a response (Auer and Griffiths, J Gambl Stud 31(3), 921-931, 2015) to a previous comment (Braverman et al., J Gambl Stud 31(2), 359-366, 2015), Auer and Griffiths suggested using "theoretical loss" as a preferable measure of gambling intensity. This comment extends and advances the discussion about measures of gambling intensity. In this paper, we describe previously identified problems that Auer and Griffiths need to address to sustain theoretical loss as a viable measure of gambling intensity and add details to the discussion that demonstrate difficulties associated with the use of theoretical loss with certain gambling games.

Lightweight structural design of a bolted case joint for the space shuttle solid rocket motor

NASA Technical Reports Server (NTRS)

Dorsey, John T.; Stein, Peter A.; Bush, Harold G.

1988-01-01

The structural design of a bolted joint with a static face seal which can be used to join Space Shuttle Solid Rocket Motor (SRM) case segments is given. Results from numerous finite element parametric studies indicate that the bolted joint meets the design requirement of preventing joint opening at the O-ring locations during SRM pressurization. A final design recommended for further development has the following parameters: 180 one-in.-diam. studs, stud centerline offset of 0.5 in radially inward from the shell wall center line, flange thickness of 0.75 in, bearing plate thickness of 0.25 in, studs prestressed to 70 percent of ultimate load, and the intermediate alcove. The design has a mass penalty of 1096 lbm, which is 164 lbm greater than the currently proposed capture tang redesign.

Sawing to reduce warp in plantation red pine studs

Treesearch

Hiram Hallock; F.B. Malcolm

1972-01-01

Large volumes of red pine (Pinus resinosa) from plantations in the Lake States and the Northeastern States are about to appear on the saw log market. One of the most important products of small saw logs is studs (2 in. x 4 in. x 8 ft.). A study has been conducted by the FPL which examines the relationship of two industrial and one FPL sawing method on the subsequent...

Sawing to reduce warp in plantation red pine studs

Treesearch

Hiram Hallock; F.B. Malcolm

1972-01-01

Large volumes of red pine ( Pinus resinosa) from plantations in the Lake States and the Northeastern States are about to appear on the saw log market. One of the most important products of small saw logs is studs (2 in. x 4 in. x 8 ft.). A study has been conducted by the FPL which examines the relationship of two industrial and one FPL sawing method on the subsequent...

Nonlinear Wave Propagation

DTIC Science & Technology

1983-12-30

Transform for the Kadomtsev - Petviashvili Equation , M.J. Ablowitz , D. Bar Yaacov and A.S. Fokas, to appear in Stud. in Appl. Math. I.N.S. #21 preprint...Benjamin-Ono equation bears many similariti to the multidimensional problem, especially the Kadomtsev - Petviashvili equation . We discuss many of these...appear in Stud. in Appl. Math. I.N.S. #22 preprint, 1982. 67. On the Inverse Scattering Transform for the Kadomtsev - Petviashvili Equation , M.J. Ablowitz

Teaching: In Light of Noel Gough's and Ajay Sharma's Articles

ERIC Educational Resources Information Center

Pouliot, Chantal

2017-01-01

In their articles, Ajay Sharma (Cult Stud Sci Educ, doi:10.1007/s11422-017-9835-z, 2017) and Noel Gough (Cult Stud Sci Educ, doi:10.1007/s11422-017-9834-0, 2017) shed light on the impact neoliberalism has on the teaching of science and suggest ways to ensure that science education remains critical and socially equitable. In this paper, I…

Experimental 3-D SAR Human Target Signature Analysis

DTIC Science & Technology

2014-07-21

is a fairly transparent one constructed of drywall made of wood studs, gypsum, insulating material, and vinyl coating on the exterior. A LIDAR image...transparent wall such as drywall , there is a significant increase in the amount of clutter and multipath. Figure 8. LIDAR imagery of a human...standing inside a building constructed of drywall made of wood stud, gypsum, insulating material, and vinyl coating. In the human standing images

High-Luminance Road Surfaces,

DTIC Science & Technology

1980-12-01

condition was changed with the decreased use of snow chains and increasing use of studded tires. The studded tires wear down the road surface in a...region, white anorthosite of a uniform and unweathered type is usable as an additive to asphalt con- crete and wear surfacing for asphalt gravel...CLASSIFICATION Of THIS PAGE(W/em Daateoo 20. Abstract (cont’d) resistance to weathering, and the degree of luminosity. Quartzites have the best wear

Harmful cleats of football boots: a biomechanical evaluation.

PubMed

Bentley, J A; Ramanathan, A K; Arnold, G P; Wang, W; Abboud, R J

2011-09-01

Football players wear boots of varying cleat designs with some preferring the bladed cleats while others opting for the conventional studded cleats. The current study compares biomechanically the boots with differing cleat designs and their effect on feet, if any. Twenty-nine healthy male volunteers were recruited from amateur football teams. They were asked to perform three trials each of two activities: a straight run and a run cutting at a 60° angle wearing bladed and studded Adidas®-F series boots on artificial turf. Plantar pressure values were recorded using the Pedar®-X in-shoe pressure measuring device. Peak pressure and pressure-time integral were analysed over 11 clinically relevant areas under the foot. While the in-shoe pressure and pressure-time integral were higher under the medial half of the foot with studded boots, they were higher under the lateral half of the foot with the bladed design. The studded boots can be considered safer as the pressure distribution across the foot and the pattern of centre of pressure progression mimicked the normal motif, whereas the bladed boots could potentially be deemed relatively more harmful due to the unnatural increased loading under the lateral half of the foot, predisposing the foot to injuries. Copyright © 2010 European Foot and Ankle Society. Published by Elsevier Ltd. All rights reserved.

Microstructures and Mechanical Properties of Friction Tapered Stud Overlap Welding for X65 Pipeline Steel Under Wet Conditions

NASA Astrophysics Data System (ADS)

Xu, Y. C.; Jing, H. Y.; Han, Y. D.; Xu, L. Y.

2017-08-01

This paper exhibits a novel in situ remediation technique named friction tapered stud overlap welding (FTSOW) to repair a through crack in structures and components in extremely harsh environments. Furthermore, this paper presents variations in process data, including rotational speed, stud displacement, welding force, and torque for a typical FTSOW weld. In the present study, the effects of welding parameters on the microstructures and mechanical properties of the welding joints were investigated. Inapposite welding parameters consisted of low rotational speeds and welding forces, and when utilized, they increased the occurrence of a lack of bonding and unfilled defects within the weld. The microstructures with a welding zone and heat-affected zone mainly consisted of upper bainite. The hardness value was highest in the welding zone and lowest in the base material. During the pull-out tests, all the welds failed in the stud. Moreover, the defect-free welds broke at the interface of the lap plate and substrate during the cruciform uniaxial tensile test. The best tensile test results at different depths and shear tests were 721.6 MPa and 581.9 MPa, respectively. The favorable Charpy impact-absorbed energy was 68.64 J at 0 °C. The Charpy impact tests revealed a brittle fracture characteristic with a large area of cleavage.

Studies in Intelligence. Volume 52, Number 4, December 2008

DTIC Science & Technology

2008-12-01

Decline and Fall of the CIA by Melvin A. Goodmandies in Intelligence Vol. 52, No. 4 (Extracts, December 2008) i In the Common Defense: National...a visiting professor at the Department of War Stud- ies , King’s College London. He has been his government’s Security and Intelligence Coordinator...wide intelligence stud- ies literature. In their essay they will normally choose the one approach with which they have come to feel most com

Preparation of reconstituted Charpy V-notch impact specimens for generating pressure vessel steel fracture toughness data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perrin, J.S.; Fromm, E.O.; Server, W.L.

1982-01-01

The arc stud welding process has been adapted for use in producing reconstituted Charpy V-notch impact specimens. In this process, each half of a tested and fractured Charpy specimen is used as the central region of a reconstituted specimen. End tabs are joined to one half of a fractured specimen by a specially designed stud welding apparatus. SA533B-1 and SA508-2 unirradiated and irradiated pressure vessel steel specimens have been produced. Both conventional and precracked reconstituted specimen data have been produced. Both types of data have been shown to be in excellent agreement with original specimen data. The arc stud weldingmore » process can therefore be used to increase the amount of data obtainable from a limited number of specimens or to obtain Charpy data when full size specimens cannot otherwise be obtained.« less

Louisiana SIP: LAC 33:III Ch 23 Subchap B, §2303--Aluminum Plants, §2303 Standards for Horizontal Stud Soderberg Primary Aluminum Plants and Prebake Primary Aluminum Plants; SIP effective 1989-05-08 (LAc49) to 2011-08-03 (LAad34 - Revised)

EPA Pesticide Factsheets

Louisiana SIP: LAC 33:III Ch 23 Subchap B, §2303--Aluminum Plants, §2303 Standards for Horizontal Stud Soderberg Primary Aluminum Plants and Prebake Primary Aluminum Plants; SIP effective 1989-05-08 (LAc49) to 2011-08-03 (LAad34 - Revised)

An Outbreak of Porcine Reproductive and Respiratory Syndrome Virus in Switzerland Following Import of Boar Semen.

PubMed

Nathues, C; Perler, L; Bruhn, S; Suter, D; Eichhorn, L; Hofmann, M; Nathues, H; Baechlein, C; Ritzmann, M; Palzer, A; Grossmann, K; Schüpbach-Regula, G; Thür, B

2016-04-01

An outbreak of porcine reproductive and respiratory syndrome virus (PRRSV) occurred in November 2012 in Switzerland (CH), traditionally PRRSV-free. It was detected after a German boar stud informed a semen importer about the detection of PRRSV during routine monitoring. Tracing of semen deliveries revealed 26 Swiss sow herds that had used semen from this stud after its last negative routine monitoring and 62 further contact herds. All herds were put under movement restrictions and examined serologically and virologically. As a first measure, 59 sows from five herds that had previously been inseminated with suspicious semen were slaughtered and tested immediately. Investigations in the stud resulted in 8 positive boars with recent semen deliveries to CH (Seven with antibodies and virus, one with antibodies only). In one boar out of six tested, virus was detected in semen. Of the 59 slaughtered sows, five from three herds were virus-positive. In one herd, the virus had spread, and all pigs were slaughtered or non-marketable animals euthanized. In the remaining herds, no further infections were detected. After confirmatory testings in all herds 3 weeks after the first examination gave negative results, restrictions were lifted in January 2013, and Switzerland regained its PRRSV-free status. The events demonstrate that import of semen from non-PRRS-free countries--even from negative studs--poses a risk, because monitoring protocols in boar studs are often insufficient to timely detect an infection, and infections of sows/herds occur even with low numbers of semen doses. The outbreak was eradicated successfully mainly due to the high disease awareness of the importer and because immediate actions were taken before clinical or laboratory diagnosis of a single case in the country was made. To minimize the risk of an introduction of PRRSV in the future, stricter import guidelines for boar semen have been implemented. © 2014 Blackwell Verlag GmbH.

Analysis of breed effects on semen traits in light horse, warmblood, and draught horse breeds.

PubMed

Gottschalk, Maren; Sieme, Harald; Martinsson, Gunilla; Distl, Ottmar

2016-05-01

In the present study, systematic effects on semen quality traits were investigated in 381 stallions representing 22 breeds. All stallions were used for AI either at the Lower Saxon National Stud Celle or the North Rhine-Westphalian National Stud Warendorf. A total of 71,078 fresh semen reports of the years 2001 to 2014 were edited for analysis of gel-free volume, sperm concentration, total number of sperm, progressive motility, and total number of progressively motile sperm. Breed differences were studied for warmblood and light horse breeds of both national studs (model I) and for warmblood breeds and the draught horse breed Rhenish German Coldblood from the North Rhine-Westphalian National stud (model II) using mixed model procedures. The fixed effects of age class, year, and month of semen collection had significant influences on all semen traits in both analyses. A significant influence of the horse breed was found for all semen traits but gel-free volume in both statistical models. Comparing warmblood and light horse stallions of both national studs, we observed highest sperm concentrations, total numbers of sperm, and total numbers of progressively motile sperm in Anglo-Arabian stallions. The draught horse breed Rhenish German Coldblood had the highest least squares means for gel-free volume, whereas all other investigated semen traits were significantly lower in this breed compared to the warmblood stallions under study. The variance components among stallions within breeds were significant for all semen traits and accounted for 40% to 59% of the total variance. The between-breed-variance among stallions was not significant underlining the similar size of the random stallion effect in each of the horse breeds analyzed here. In conclusion, breed and stallion are accounting for a significant proportion of the variation in semen quality. Copyright © 2016 Elsevier Inc. All rights reserved.

Full-Scale Evaluation of DuraDeck (registered trademark) and MegaDeck (trademark) Matting Systems

DTIC Science & Technology

2013-07-01

plates studded with threaded bolts were placed ERDC/GSL TR-13-27 10 underneath two pre-drilled corners of the panel. The plates were positioned so...metal plates studded with threaded ERDC/GSL TR-13-27 4 Figure 1. DuraDeck® mat panel, top surface. Figure 2. DuraDeck® mat panel, bottom surface...ERDC/GSL TR-13-27 5 bolts , as shown in Figure 3, underneath the mat corners and then installing special connector nuts from the top surface

Teaching: in light of Noel Gough's and Ajay Sharma's articles

NASA Astrophysics Data System (ADS)

Pouliot, Chantal

2017-12-01

In their articles, Ajay Sharma (Cult Stud Sci Educ, doi: 10.1007/s11422-017-9835-z, 2017) and Noel Gough (Cult Stud Sci Educ, doi: 10.1007/s11422-017-9834-0, 2017) shed light on the impact neoliberalism has on the teaching of science and suggest ways to ensure that science education remains critical and socially equitable. In this paper, I illustrate how their proposals influenced my instructional choices during the fall of 2016 in a course entitled Epistemology and Education.

Structural optimization of an alternate design for the Space Shuttle solid rocket booster field joint

NASA Technical Reports Server (NTRS)

Barthelemy, Jean-Francois M.; Rogers, James L., Jr.; Chang, Kwan J.

1987-01-01

A structural optimization procedure is used to determine the shape of an alternate design for the Shuttle's solid rocket booster field joint. In contrast to the tang and clevis design of the existing joint, this alternate design consists of two flanges bolted together. Configurations with 150 studs of 1 1/8 in diameter and 135 studs of 1 3/16 in diameter are considered. Using a nonlinear programming procedure, the joint weight is minimized under constraints on either von Mises or maximum normal stresses, joint opening and geometry. The procedure solves the design problem by replacing it by a sequence of approximate (convex) subproblems; the pattern of contact between the joint halves is determined every few cycles by a nonlinear displacement analysis. The minimum weight design has 135 studs of 1 3/16 in diameter and is designed under constraints on normal stresses. It weighs 1144 lb per joint more than the current tang and clevis design.

Development of Lead Free Energy Absorber for Space Shuttle Blast Container

NASA Technical Reports Server (NTRS)

Ingram, T.; Balles, D.; Schricker, A.; Novak, H.

1998-01-01

The Space Shuttle vehicle (SSV) is connected to the mobile launch platform (MLP) by four aft skirt hold down studs on each solid rocket booster (SRB). Prior to lift-off, the frangible nuts inside the aft skirt blast containers (BC) are severed into two nut halves by two pyrotechnic booster cartridges. This action releases the SSV and allows the hold down studs to eject through the aft skirt bore and then down into the MLP. USBI has been tasked to upgrade the BC for two specific reasons; 1. to eliminate lead for environmental concerns, and 2. to reduce the chance of nut recontact with the holddown stud. Nut recontact with the stud has been identified as a likely contributor to stud hangups. This upgrade will replace the lead liner with an aluminum foam material. The aluminum foam used as a energy absorber is a proven design in many other aerospace/defense applications. Additional benefits of using the open cell, energy absorbent aluminum foam in place of the solid lead liner are: A. Lead handling/ exposure, and possible contamination, along with hazardous waste disposal will be eliminated; B. Approximately 200 lbs. weight savings will be contributed to each Space Shuttle flight by using aluminum foam over lead; C. The new aluminum liner is designed to catch all shrapnel from frangible nuts thus virtually eliminating chance of foreign object debris (FOD) exiting the HDP, and causing potential damage to the vehicle; D. Potential of using the lighter aluminum liner over lead, allows for easier assembly and disassembly of blast container elements, also allowing for improvements in safety, operator handling, and efficiency of operations. Six BC firing tests will be required to determine if the new liner material will perform in a way to decrease the chance of stud hangups and enhance the ability of the BC to retain blast debris. Testing will be performed at the Kennedy Space Center (KSC) facility known as the Launch Equipment Test Facility (LETF), and will simulate the SRB hold- down post, with actual BC hardware and pyrotechnics assembled, and then test fired. Initial testing was performed in 1997 using a frangible nut in a static drop test over lead and aluminum foam sheet materials. The aluminum foam showed a dramatic improvement of energy absorption over the lead liner material. Proof-of-Principle testing at the KSC-LETF commenced in May, 1998, and is expected to be completed by June, 1998.

[Death caused by projectile guns--a retrospective analysis of 34 cases in Berlin and Hamburg].

PubMed

Lignitz, E; Koops, E; Püschel, K

1988-01-01

The autopsy material of the institutes for forensic medicine in Berlin/GDR and Hamburg was analyzed retrospectively (period from 1961 till 1987; 70,000 autopsies) for fatalities caused by "humane killers" (n = 22) and stud guns (n = 12).-Epidemiological, criminological and morphological findings: The decreased were all men aged between 18 and 75 years (mean 48 years) except one 61 year-old paraplegic women who was killed by her husband with a humane killer. The great majority of cases consisted of suicides; two accidents at work were caused by stud guns. These unusual weapons are normally used by skilled people (i.e. butchers or constructional workers respectively). The fatal wounds were situated at the head, especially the forehead, seldom at the nape of the neck or in the mouth, or sometimes in the chest when using stud guns. Combined suicides (especially together with hanging) are not unusual. Survival periods (with or without acting capacity) can range between minutes or even months (after neurosurgical intervention).-The frequency of such unusual and overall rare cases did not raise during the investigation period.

Correlation Study of Laboratory Physical and Chemical Data with Dynamometer Engine Sequence Performance Testing of Engine Lubricating Oils.

DTIC Science & Technology

1978-12-01

and chemical data and dynamomet er and field perfo rmance. The initial stud y produced internal and group correlations among the data and suggests a...sm all (a corre lation of I .0 i~ ~~r kct cor rela t ion ’, Prin cip al comp onent .iii,il ~ 515 Was enmp lo~ ed to stud ~ lhe iner al l re hi t i...Additive ) K = Potassium (Addit ive) V N = Nitr ogen (Additive ) . V Mg = Magnesium (Additive ) B = Boron (Additive ) Other = To include wear and

Detection of atypical porcine pestivirus in semen from commercial boar studs in the United States.

PubMed

Gatto, I R H; Arruda, P H; Visek, C A; Victoria, J G; Patterson, A R; Krull, A C; Schwartz, K J; de Oliveira, L G; Arruda, B L

2018-04-01

Atypical porcine pestivirus (APPV) has recently been identified as a cause of congenital tremor (CT) in pigs and has been detected in semen and preputial swabs from boars that were known to be clinically affected with CT. Accordingly, the objectives of this study were to 1) detect the presence of APPV in semen, preputial fluids and preputial swabs from adult boars by quantitative reverse transcription PCR (qRT-PCR) and 2) genetically characterize a subset of positive samples to better understand the ecology of APPV in commercial boar studs and the potential risk of transmission of APPV via semen. A total of 597 samples of semen, preputial fluid and preputial swabs each representing a different boar were obtained from four commercial boar studs located in three different states in the United States. Viral RNA was detected by qRT-PCR in 90 samples (15.08%; 90/597), with the greatest per cent positive from preputial swabs (23.81%; 5/21) followed by preputial fluid (22.81%; 26/114) and semen (12.91%; 59/457). The mean cycle quantification (Cq) between sample types was similar while eleven semen samples had Cq values lower than 27.0 corresponding to approximately 2 × 10 6  copies/ml. Based on phylogenetic analysis of the Npro gene, different viral strains can be on the same farm at the same and different times. This is the first report of detection of APPV in semen from commercial boar studs. Studies investigating the role of semen in the transmission of APPV and production of CT are needed. © 2017 Blackwell Verlag GmbH.

Examination, evaluation and repair of laminated wood blades after service on the Mod-OA wind turbine

NASA Technical Reports Server (NTRS)

Faddoul, J. R.

1983-01-01

Laminated wood blades were designed, fabricated, and installed on a 200-KW wind turbine (Mod-OA). The machine uses a two-blade rotor with a diameter of 38.1 m (125 ft). Each blade weights less than 1361 kg (3000 lb). After operating in the field, two blade sets were returned for inspection. One set had been in Hawaii for 17 months (7844 hr of operation) and the other had been at Block Island, Rhode Island, for 26 months (22 months operating - 7564 hr). The Hawaii set was returned because of one of the studs that holds the blade to the hub had failed. This was found to be caused by a combination of improper installation and inadequate corrosion protection. No other problems were found. The broken stud (along with four others that were badly corroded) was replaced and the blades are now in storage. The Block Island set of blades was returned at the completion of the test program, but one blade was found to have developed a crack in the leading edge along the entire span. This crack was found to be the result of a manufacturing process problem but was not structurally critical. When a load-deflection test was conducted on the cracked blade, the response was identical to that measured before installation. In general, the laminate quality of both blade sets was excellent. No significant internal delamination or structural defects were found in any blade. The stud bonding process requires close tolerance control and adequate corrosion protection, but studs can be removed and replaced without major problems. Moisture content stabilization does not appear to be a problem, and laminated wood blades are satisfactory for long-term operation on Mod-OA wind turbines.

Ultrasonic inspection of studs (bolts) using dynamic predictive deconvolution and wave shaping.

PubMed

Suh, D M; Kim, W W; Chung, J G

1999-01-01

Bolt degradation has become a major issue in the nuclear industry since the 1980's. If small cracks in stud bolts are not detected early enough, they grow rapidly and cause catastrophic disasters. Their detection, despite its importance, is known to be a very difficult problem due to the complicated structures of the stud bolts. This paper presents a method of detecting and sizing a small crack in the root between two adjacent crests in threads. The key idea is from the fact that the mode-converted Rayleigh wave travels slowly down the face of the crack and turns from the intersection of the crack and the root of thread to the transducer. Thus, when a crack exists, a small delayed pulse due to the Rayleigh wave is detected between large regularly spaced pulses from the thread. The delay time is the same as the propagation delay time of the slow Rayleigh wave and is proportional to the site of the crack. To efficiently detect the slow Rayleigh wave, three methods based on digital signal processing are proposed: wave shaping, dynamic predictive deconvolution, and dynamic predictive deconvolution combined with wave shaping.

Influence of Cleats-Surface Interaction on the Performance and Risk of Injury in Soccer: A Systematic Review

PubMed Central

Macedo, Rui; Montes, António Mesquita

2017-01-01

Objective To review the influence of cleats-surface interaction on the performance and risk of injury in soccer athletes. Design Systematic review. Data Sources Scopus, Web of science, PubMed, and B-on. Eligibility Criteria Full experimental and original papers, written in English that studied the influence of soccer cleats on sports performance and injury risk in artificial or natural grass. Results Twenty-three articles were included in this review: nine related to performance and fourteen to injury risk. On artificial grass, the soft ground model on dry and wet conditions and the turf model in wet conditions are related to worse performance. Compared to rounded studs, bladed ones improve performance during changes of directions in both natural and synthetic grass. Cleat models presenting better traction on the stance leg improve ball velocity while those presenting a homogeneous pressure across the foot promote better kicking accuracy. Bladed studs can be considered less secure by increasing plantar pressure on lateral border. The turf model decrease peak plantar pressure compared to other studded models. Conclusion The soft ground model provides lower performance especially on artificial grass, while the turf model provides a high protective effect in both fields. PMID:28684897

Influence of Cleats-Surface Interaction on the Performance and Risk of Injury in Soccer: A Systematic Review.

PubMed

Silva, Diogo C F; Santos, Rubim; Vilas-Boas, João Paulo; Macedo, Rui; Montes, António Mesquita; Sousa, Andreia S P

2017-01-01

To review the influence of cleats-surface interaction on the performance and risk of injury in soccer athletes. Systematic review. Scopus, Web of science, PubMed, and B-on. Full experimental and original papers, written in English that studied the influence of soccer cleats on sports performance and injury risk in artificial or natural grass. Twenty-three articles were included in this review: nine related to performance and fourteen to injury risk. On artificial grass, the soft ground model on dry and wet conditions and the turf model in wet conditions are related to worse performance. Compared to rounded studs, bladed ones improve performance during changes of directions in both natural and synthetic grass. Cleat models presenting better traction on the stance leg improve ball velocity while those presenting a homogeneous pressure across the foot promote better kicking accuracy. Bladed studs can be considered less secure by increasing plantar pressure on lateral border. The turf model decrease peak plantar pressure compared to other studded models. The soft ground model provides lower performance especially on artificial grass, while the turf model provides a high protective effect in both fields.

Sound transmission through lightweight double-leaf partitions: theoretical modelling

NASA Astrophysics Data System (ADS)

Wang, J.; Lu, T. J.; Woodhouse, J.; Langley, R. S.; Evans, J.

2005-09-01

This paper presents theoretical modelling of the sound transmission loss through double-leaf lightweight partitions stiffened with periodically placed studs. First, by assuming that the effect of the studs can be replaced with elastic springs uniformly distributed between the sheathing panels, a simple smeared model is established. Second, periodic structure theory is used to develop a more accurate model taking account of the discrete placing of the studs. Both models treat incident sound waves in the horizontal plane only, for simplicity. The predictions of the two models are compared, to reveal the physical mechanisms determining sound transmission. The smeared model predicts relatively simple behaviour, in which the only conspicuous features are associated with coincidence effects with the two types of structural wave allowed by the partition model, and internal resonances of the air between the panels. In the periodic model, many more features are evident, associated with the structure of pass- and stop-bands for structural waves in the partition. The models are used to explain the effects of incidence angle and of the various system parameters. The predictions are compared with existing test data for steel plates with wooden stiffeners, and good agreement is obtained.

Controlling Laser-Plasma Instabilities and CBET Using STUD Pulses in the Strong Coupling Regime for Direct and Indirect Drive ICF

NASA Astrophysics Data System (ADS)

Afeyan, Bedros; Meezan, N.; MacLaren, S.; Hammer, J.; Montgomery, D.; Heebner, J.

2015-11-01

We will show theoretical results on the behavior of SBS in the strong damping regime and CBET in mid-Z plasmas (around 20) where ion Landau damping and collisional damping are both higher order effects and strong coupling is dominant in laser hot spots and near Mach -1 surfaces in appropriately tuned pairs of crossing beams. The spatially dependent frequency shits that ensue and the reductions in growth rate allow the control of LPI even downstream beyond the crossing volumes. Multiple successive crossings between O(100) beams can be used to change the space-time intensity distributions of lasers used entirely differently in direct and indirect drive geometries. In the former case, due to the existence of many angles, a statistical Sqrt(N) gain is expected. with randomly phased beams via STUD pulses. On the other hand, for indirect drive, with 2-4 cone angles to contend with, turning off interactions by staggering crossing beam spikes, achieved with STUD pulses, is a key deterministic element for the success of the plan. Changing the speckle statistics at will and with fine control is a grand challenge of this set of techniques.

Retention and wear behaviors of two implant overdenture stud-type attachments at different implant angulations.

PubMed

Choi, Jae-Won; Bae, Ji-Hyeon; Jeong, Chang-Mo; Huh, Jung-Bo

2017-05-01

Implant angulation should be considered when selecting an attachment. Some in vitro studies have investigated the relationship between implant angulation and changes in the retention force of the stud attachment, but few studies have evaluated the effect of cyclic loading and repeated cycles of insertion and removal on the stud attachment. The purpose of this in vitro study was to evaluate the effects of implant angulation on the retentive characteristics of overdentures with 2 different stud attachments, an experimental system and O-rings in red and orange, after cyclic loading and repeated insertion and removal cycles. The canine region of a mandibular experimental model was fitted with 2 implant fixtures with 2 different stud attachment systems at implant angulations of 0, 15, or 30 degrees. A mastication simulator was used to simulate cyclic loading, and a universal testing machine was used to evaluate retentive force changes after repeated insertion and removal cycles. To simulate the numbers of mastication and insertion and removal cycles per annum, 400000 cyclic loadings and 1080 insertion and removal cycles were performed. Wear patterns and attachment surface deformations were evaluated by scanning electron microscopy. Data were analyzed using the Kruskal-Wallis test, Mann-Whitney U test with Bonferroni correction (α=.05/3=.017), and the paired-sample Student t test (α=.05). When retentive forces before and after testing were compared, O-ring showed significant retention loss at all implant angulations (P<.001). In contrast, the experimental system showed little retention loss in the 0- and 15-degree models (P>.05), whereas the 30-degree model showed a significant increase in retentive force (P=.001). At all implant angulations, retention loss increased significantly for the orange O-ring, followed by the red O-ring, and the experimental system (P<.001). Scanning electron microscopy analysis showed more intense wear in the matrix than the patrix (abutment that matches to matrix) and more severe wear and deformation of the O-ring rubber matrix than of the experimental zirconia ball. Upon completion of the experiment, wear and deformation were found for all attachment systems. Even when implants are not installed in parallel, the experimental system can be used without involving great loss of retention. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Thermal conductivity on stud bump interconnection of high power COB LED

NASA Astrophysics Data System (ADS)

Sarukunaselan, K.; Ong, N. R.; Sauli, Z.; Mahmed, N.; Kirtsaeng, S.; Sakuntasathien, S.; Suppiah, S.; Alcain, J. B.; Retnasamy, V.

2017-09-01

In this paper, the impacts of bump dimensions and material conductivity on the thermal performances of a high power chip on board (COB) LED package were investigated using open source software, Elmer. The stud bump acted as interconnection join which has an extra role in dissipating heat generated by the chip to the ambience. Simulation data showed that for a bump with a fixed contact length of 1mm, the most suitable height was 171 µm with material conductivity of 238W/mK or 319W/mK. Materials with thermal conductivity of lower than 20W/mK, had the poorest heat dissipation irrespective of the height.

[Particle numbers in classified sizes of roadside dust caused by studded tires in the air at different heights from the pavement surface].

PubMed

Sato, T; Niioka, T; Kurasaki, M; Kojima, Y

1996-07-01

Increased use of motor vehicles has produced various risks to human health due to air pollution by noxious gases, heavy metals and roadside dust. Since the late 1970s, the wide spread use of studded tires for cars has caused pavement wear, resulting in not only economic losses, but also roadside air pollution in cold and snowy regions in Japan. The most serious environmental problem in Sapporo, a city with heavy snowfall, in the 1980s, was roadside dust derived from studded tires. The inhabitants suffered from this dust in the early winter and in the early spring when the streets were not covered with snow. To investigate the influence of such roadside dust upon human health, particle numbers in classified sizes of roadside dust were counted after the roadside dust in the air was collected with a device we constructed at 30, 60, 90, 120, 150, and 180 cm above the pavement surface. The results indicated that the concentration of roadside dust in the air did not greatly vary according to the height from the pavement surface. The results also suggested that xenogranuloma, reported in lungs of stray dogs, under roadside dust-pollution conditions such as those examined here, may occur in humans in the future.

Clinical, serological and virological characteristics of an outbreak of paresis and neonatal foal disease due to equine herpesvirus-1 on a stud farm.

PubMed

McCartan, C G; Russell, M M; Wood, J L; Mumford, J A

1995-01-07

An outbreak of equine herpesvirus-1 (EHV-1) occurred on a large stud farm with 133 mares, 54 foals and four stallions, and at least 85 mares, 22 foals and three stallions were infected. Clinical disease was observed in 16 mares, two stallions and 13 foals and the predominant clinical signs were scrotal oedema, ataxia and loss of libido in the stallions, ataxia and recumbency in the mares and uveitis and nasal discharge in the foals, although pneumonia and colic with intussusception were also recorded at autopsy. Neurological disease was more common in the mares nursing foals (12 of 38 infected) than in barren mares (one of 46 infected). Three mares died during the outbreak and no mares that had been recumbent bred again. Control procedures were based on virological and serological testing and stringent management practices to limit the spread of infection between groups of mares and foals and away from the stud farm. There were marked antibody responses in the adult horses, but they were generally poor in the foals; three of the nine viraemic foals did not develop significant increases in the levels of circulating antibody. Recommendations are made for the management of future outbreaks.

The improvement of a simple theoretical model for the prediction of the sound insulation of double leaf walls.

PubMed

Davy, John L

2010-02-01

This paper presents a revised theory for predicting the sound insulation of double leaf cavity walls that removes an approximation, which is usually made when deriving the sound insulation of a double leaf cavity wall above the critical frequencies of the wall leaves due to the airborne transmission across the wall cavity. This revised theory is also used as a correction below the critical frequencies of the wall leaves instead of a correction due to Sewell [(1970). J. Sound Vib. 12, 21-32]. It is found necessary to include the "stud" borne transmission of the window frames when modeling wide air gap double glazed windows. A minimum value of stud transmission is introduced for use with resilient connections such as steel studs. Empirical equations are derived for predicting the effective sound absorption coefficient of wall cavities without sound absorbing material. The theory is compared with experimental results for double glazed windows and gypsum plasterboard cavity walls with and without sound absorbing material in their cavities. The overall mean, standard deviation, maximum, and minimum of the differences between experiment and theory are -0.6 dB, 3.1 dB, 10.9 dB at 1250 Hz, and -14.9 dB at 160 Hz, respectively.

An experimental test for indirect benefits in Drosophila melanogaster

PubMed Central

Rundle, Howard D; Ödeen, Anders; Mooers, Arne Ø

2007-01-01

Background Despite much empirical attention, tests for indirect benefits of mate choice have rarely considered the major components of sexual and nonsexual offspring fitness relevant to a population. Here we use a novel experimental design to test for the existence of any indirect benefits in a laboratory adapted population of D. melanogaster. Our experiment compared the fitness (mating success, longevity, and productivity) of individuals possessing genomes that derived two generations previously from males that were either entirely successful (studs) or wholly unsuccessful (duds) at achieving mates in three subsequent rounds of mating trials. Results Males from the stud treatment were 30% more successful on average at securing mates than males from the dud treatment. In contrast, we found no difference between treatments in measures of productivity or of longevity when measured in a mixed-sex environment. In the absence of females, however, males in the stud treatment outlived males in the dud treatment. Conclusion Our results suggest that mating with successful males in this population provides an indirect benefit to females and that, at least in this environment, the benefit arises primarily through the production of more attractive male offspring. However, it is unclear whether this represents solely a traditional sexy sons benefit or whether there is an additional good genes component (with male offspring simply allocating their surplus condition to traits that enhance their mating success). The lack of any detectable differences in female fitness between the two treatments suggests the former, although the longevity advantage of males in the stud treatment when females were absent is consistent with the latter. Determining the effect of this indirect benefit on the evolution of female mate preferences (or resistance) will require comparable data on the direct costs of mating with various males, and an understanding of how these costs and benefits integrate across generations and vary among environments. PMID:17349042

Tongue piercing and insertion of metal studs: three cases of dental and oral consequences.

PubMed

Ram, D; Peretz, B

2000-01-01

"Body art" is a fashion that appears to be gaining popularity worldwide. There are many risks and potentially adverse results associated with tongue piercing. Pain (the procedure is performed without anesthetics), post-placement edema and the risk of prolonged bleeding, if the blood vessels are punctured during the piercing, and fracture of tooth structures, are but a few of the risks. The purpose of the present article is to describe the consequences of three cases of tongue piercing in which metallic barbell-shaped studs were inserted: the consequences include the fracture of tooth structure, caused by the device knocking against the teeth; and inflammation and edema occurred as a result of the piercing of the tongue.

Apparatus for testing high pressure injector elements

NASA Technical Reports Server (NTRS)

Myers, William Neill (Inventor); Scott, Ewell M. (Inventor); Forbes, John C. (Inventor); Shadoan, Michael D. (Inventor)

1995-01-01

An apparatus for testing and evaluating the spray pattern of high pressure fuel injector elements for use in supplying fuel to combustion engines is presented. Prior art fuel injector elements were normally tested by use of low pressure apparatuses which did not provide a purge to prevent mist from obscuring the injector element or to prevent frosting of the view windows; could utilize only one fluid during each test; and had their viewing ports positioned one hundred eighty (180 deg) apart, thus preventing optimum use of laser diagnostics. The high pressure fluid injector test apparatus includes an upper hub, an upper weldment or housing, a first clamp and stud/nut assembly for securing the upper hub to the upper weldment, a standoff assembly within the upper weldment, a pair of window housings having view glasses within the upper weldment, an injector block assembly and purge plate within the upper weldment for holding an injector element to be tested and evaluated, a lower weldment or housing, a second clamp and stud/nut assembly for securing the lower weldment to the upper hub, a third clamp and stud/nut assembly for securing the lower hub to the lower weldment, mechanisms for introducing fluid under high pressure for testing an injector element, and mechanisms for purging the apparatus to prevent frosting of view glasses within the window housings and to permit unobstructed viewing of the injector element.

Apparatus for testing high pressure injector elements

NASA Technical Reports Server (NTRS)

Myers, William Neill (Inventor); Scott, Ewell M. (Inventor); Forbes, John C. (Inventor); Shadoan, Michael D. (Inventor)

1993-01-01

An apparatus for testing and evaluating the spray pattern of high pressure fuel injector elements for use in supplying fuel to combustion engines is presented. Prior art fuel injector elements were normally tested by use of low pressure apparatuses which did not provide a purge to prevent mist from obscuring the injector element or to prevent frosting of the view windows; could utilize only one fluid during each test; and had their viewing ports positioned one hundred eighty (180 deg) apart, thus preventing optimum use of laser diagnostics. The high pressure fluid injector test apparatus includes an upper hub, an upper weldment or housing, a first clamp and stud/nut assembly for securing the upper hub to the upper weldment, a standoff assembly within the upper weldment, a pair of window housings having view glasses within the upper weldment, an injector block assembly and purge plate within the upper weldment for holding an injector element to be tested and evaluated, a lower weldment or housing, a second clamp and stud/nut assembly for securing the lower weldment to the upper weldment, a lower hub, a third clamp and stud/nut assembly for securing the lower hub to the lower weldment, mechanisms for introducing fluid under high pressure for testing an injector element, and mechanisms for purging the apparatus to prevent frosting of view glasses within the window housings and to permit unobstructed viewing of the injector element.

Understanding the limits of Marxist approaches to sociocultural studies of science education

NASA Astrophysics Data System (ADS)

Lima Junior, Paulo; Ostermann, Fernanda; Rezende, Flavia

2014-09-01

In the first three sections of this paper we comment on some of the ideas developed in the forum papers, pointing out possible misunderstandings and constructing new explanations that clarify arguments we made in the original article. In the last section we expand the discussion raised in the original paper, elaborating on the limits of the use of Marxist approaches to sociocultural studies of science education. Following insights suggested by Loxley et al. (Cult Stud Sci Edu. doi: 10.1007/s11422-013-9554-z, 2013) and detailed by Zuss (Cult Stud Sci Edu, 2014) on the commodification of knowledge, we sketch an analysis of how knowledge is transformed into capital to understand why contemporary scholars are likely to be engaged in a relation of production that resembles capitalist exploitation.

Improved Reliability of SiC Pressure Sensors for Long Term High Temperature Applications

NASA Technical Reports Server (NTRS)

Okojie, R. S.; Nguyen, V.; Savrun, E.; Lukco, D.

2011-01-01

We report advancement in the reliability of silicon carbide pressure sensors operating at 600 C for extended periods. The large temporal drifts in zero pressure offset voltage at 600 C observed previously were significantly suppressed to allow improved reliable operation. This improvement was the result of further enhancement of the electrical and mechanical integrity of the bondpad/contact metallization, and the introduction of studded bump bonding on the pad. The stud bump contact promoted strong adhesion between the Au bond pad and the Au die-attach. The changes in the zero offset voltage and bridge resistance over time at temperature were explained by the microstructure and phase changes within the contact metallization, that were analyzed with Auger electron spectroscopy (AES) and field emission scanning electron microscopy (FE-SEM).

Combinatorial materials research applied to the development of new surface coatings VII: An automated system for adhesion testing

NASA Astrophysics Data System (ADS)

Chisholm, Bret J.; Webster, Dean C.; Bennett, James C.; Berry, Missy; Christianson, David; Kim, Jongsoo; Mayo, Bret; Gubbins, Nathan

2007-07-01

An automated, high-throughput adhesion workflow that enables pseudobarnacle adhesion and coating/substrate adhesion to be measured on coating patches arranged in an array format on 4×8in.2 panels was developed. The adhesion workflow consists of the following process steps: (1) application of an adhesive to the coating array; (2) insertion of panels into a clamping device; (3) insertion of aluminum studs into the clamping device and onto coating surfaces, aligned with the adhesive; (4) curing of the adhesive; and (5) automated removal of the aluminum studs. Validation experiments comparing data generated using the automated, high-throughput workflow to data obtained using conventional, manual methods showed that the automated system allows for accurate ranking of relative coating adhesion performance.

Use of an implant o-ring attachment for the tooth supported mandibular overdenture: a clinical report.

PubMed

Guttal, Satyabodh S; Tavargeri, Anand K; Nadiger, Ramesh K; Thakur, Srinath L

2011-07-01

Retention of a mandibular denture can be achieved by an implant-retained or natural tooth-retained bar and stud attachment in the anterior segment of the mandible. The same design principles holds true for both implant-retained and tooth-retained methods of anchoring the bar and stud attachment. A simple and cost effective treatment for more complex implant overdenture is the concept of conventional tooth-retained overdentures. When few firm teeth still remain in a compromised dentition, preservation of these teeth for overdentures can improve retention and stability. The authors present a clinical report of a patient treated with a mandibular tooth-borne overdenture with bar and O-ring attachment. A splinted bar supported the prosthesis and an O-ring retained the denture.

Use of an Implant O-Ring Attachment for the Tooth Supported Mandibular Overdenture: A Clinical Report

PubMed Central

Guttal, Satyabodh S.; Tavargeri, Anand K.; Nadiger, Ramesh K.; Thakur, Srinath L.

2011-01-01

Retention of a mandibular denture can be achieved by an implant-retained or natural tooth-retained bar and stud attachment in the anterior segment of the mandible. The same design principles holds true for both implant-retained and tooth-retained methods of anchoring the bar and stud attachment. A simple and cost effective treatment for more complex implant overdenture is the concept of conventional tooth-retained overdentures. When few firm teeth still remain in a compromised dentition, preservation of these teeth for overdentures can improve retention and stability. The authors present a clinical report of a patient treated with a mandibular tooth-borne overdenture with bar and O-ring attachment. A splinted bar supported the prosthesis and an O-ring retained the denture. PMID:21769276

Ultrasonic extensometer measures bolt preload

NASA Technical Reports Server (NTRS)

Daniels, C. M., Jr.

1978-01-01

Extensometer using ultrasonic pulse reflections to measure elongations in tightened belts and studs is much more accurate than conventional torque wrenches in application of specified preload to bolts and other threaded fasteners.

Pleural Touch Preparations and Direct Visualization of the Pleura during Medical Thoracoscopy for the Diagnosis of Malignancy.

PubMed

Grosu, Horiana B; Vial-Rodriguez, Macarena; Vakil, Erik; Casal, Roberto F; Eapen, George A; Morice, Rodolfo; Stewart, John; Sarkiss, Mona G; Ost, David E

2017-08-01

During diagnostic thoracoscopy, talc pleurodesis after biopsy is appropriate if the probability of malignancy is sufficiently high. Findings on direct visual assessment of the pleura during thoracoscopy, rapid onsite evaluation (ROSE) of touch preparations (touch preps) of thoracoscopic biopsy specimens, and preoperative imaging may help predict the likelihood of malignancy; however, data on the performance of these methods are limited. To assess the performance of ROSE of touch preps, direct visual assessment of the pleura during thoracoscopy, and preoperative imaging in diagnosing malignancy. Patients who underwent ROSE of touch preps during thoracoscopy for suspected malignancy were retrospectively reviewed. Malignancy was diagnosed on the basis of final pathologic examination of pleural biopsy specimens. ROSE results were categorized as malignant, benign, or atypical cells. Visual assessment results were categorized as tumor studding present or absent. Positron emission tomography (PET) and computed tomography (CT) findings were categorized as abnormal or normal pleura. Likelihood ratios were calculated for each category of test result. The study included 44 patients, 26 (59%) with a final pathologic diagnosis of malignancy. Likelihood ratios were as follows: for ROSE of touch preps: malignant, 1.97 (95% confidence interval [CI], 0.90-4.34); atypical cells, 0.69 (95% CI, 0.21-2.27); benign, 0.11 (95% CI, 0.01-0.93); for direct visual assessment: tumor studding present, 3.63 (95% CI, 1.32-9.99); tumor studding absent, 0.24 (95% CI, 0.09-0.64); for PET: abnormal pleura, 9.39 (95% CI, 1.42-62); normal pleura, 0.24 (95% CI, 0.11-0.52); and for CT: abnormal pleura, 13.15 (95% CI, 1.93-89.63); normal pleura, 0.28 (95% CI, 0.15-0.54). A finding of no malignant cells on ROSE of touch preps during thoracoscopy lowers the likelihood of malignancy significantly, whereas finding of tumor studding on direct visual assessment during thoracoscopy only moderately increases the likelihood of malignancy. A positive finding on PET and/or CT increases the likelihood of malignancy significantly in a moderate-risk patient group and can be used as an adjunct to predict malignancy before pleurodesis.

Electrochemical chloride extraction : influence of concrete surface on treatment.

DOT National Transportation Integrated Search

2002-10-01

One bridge restoration technique available for reducing corrosion-induced concrete deterioration, which removes : chloride ions while simultaneously realkalizing the concrete adjacent to the steel, is electrochemical chloride extraction : (ECE). Stud...

Research notes : September 1995.

DOT National Transportation Integrated Search

1995-09-01

The Repair of Rutting Caused by Studded Tires Literature Review was prepared to document the alternatives available for Oregon pavements. Other study objectives included determining the viability of the alternatives with regard to material costs (inc...

Road weather management performance metrics.

DOT National Transportation Integrated Search

2008-04-29

This report presents the results of a study to identify appropriate measures of performance that can be attributed to the Federal Highway Administrations (FHWA) Road Weather Management Program (RWMP) products and activities. Specifically, the stud...

Understanding the limits of Marxist approaches to sociocultural studies of science education

NASA Astrophysics Data System (ADS)

Lima, Paulo; Ostermann, Fernanda; Rezende, Flavia

2014-12-01

In the first three sections of this paper we comment on some of the ideas developed in the forum papers, pointing out possible misunderstandings and constructing new explanations that clarify arguments we made in the original article. In the last section we expand the discussion raised in the original paper, elaborating on the limits of the use of Marxist approaches to sociocultural studies of science education. Following insights suggested by Loxley et al. (Cult Stud Sci Educ. doi: 10.1007/s11422-013-9554-z, 2013) and detailed by Zuss (Cult Stud Sci Educ. doi: 10.1007/s11422-013-9555-y, 2014) on the commodification of knowledge, we sketch an analysis of how knowledge is transformed into capital to understand why contemporary scholars are likely to be engaged in a relation of production that resembles capitalist exploitation.

Testing of Compact Bolted Fasteners with Insulation and Friction-Enhanced Shims for NCSX

DOE Office of Scientific and Technical Information (OSTI.GOV)

L. E. Dudek, J.H. Chrzanowski, G. Gettelfinger, P. Heitzenroeder, S. Jurczynski, M. Viola and K. Freudenberg

The fastening of the National Compact Stellarator Experiment's (NCSX) modular coils presented a number of engineering and manufacturing challenges due to the high magnetic forces, need to control induced currents, tight tolerances and restrictive space envelope. A fastening method using high strength studs, jack nuts, insulating spacers, bushings and alumina coated shims was developed which met the requirements. A test program was conducted to verify the design. The tests included measurements of flatness of the spacers, determination of contact area, torque vs. tension of the studs and jack nuts, friction coefficient tests on the alumina and G-10 insulators, electrical tests,more » and tension relaxation tests due to temperature excursions from room temperature to liquid nitrogen temperatures. This paper will describe the design and the results of the test program.« less

Implications of the pH and temperature of diluted, cooled boar semen on fresh and frozen-thawed sperm motility characteristics.

PubMed

Purdy, P H; Tharp, N; Stewart, T; Spiller, S F; Blackburn, H D

2010-10-15

Boar semen is typically collected, diluted and cooled for AI use over numerous days, or frozen immediately after shipping to capable laboratories. The storage temperature and pH of the diluted, cooled boar semen could influence the fertility of boar sperm. Therefore, the purpose of this study was to determine the effects of pH and storage temperature on fresh and frozen-thawed boar sperm motility end points. Semen samples (n = 199) were collected, diluted, cooled and shipped overnight to the National Animal Germplasm Program laboratory for freezing and analysis from four boar stud facilities. The temperature, pH and motility characteristics, determined using computer automated semen analysis, were measured at arrival. Samples were then cryopreserved and post-thaw motility determined. The commercial stud was a significant source of variation for mean semen temperature and pH, as well as total and progressive motility, and numerous other sperm motility characteristics. Based on multiple regression analysis, pH was not a significant source of variation for fresh or frozen-thawed boar sperm motility end points. However, significant models were derived which demonstrated that storage temperature, boar, and the commercial stud influenced sperm motility end points and the potential success for surviving cryopreservation. We inferred that maintaining cooled boar semen at approximately 16 °C during storage will result in higher fresh and frozen-thawed boar sperm quality, which should result in greater fertility. Copyright © 2010 Elsevier Inc. All rights reserved.

Effects of Two Football Stud Types on Knee and Ankle Kinetics of Single-Leg Land-Cut and 180° Cut Movements on Infilled Synthetic Turf.

PubMed

Bennett, Hunter J; Brock, Elizabeth; Brosnan, James T; Sorochan, John C; Zhang, Songning

2015-10-01

Higher ACL injury rates have been recorded in cleats with higher torsional resistance in American football, which warrants better understanding of shoe/stud-dependent joint kinetics. The purpose of this study was to determine differences in knee and ankle kinetics during single-leg land cuts and 180° cuts on synthetic infilled turf while wearing 3 types of shoes. Fourteen recreational football players performed single-leg land cuts and 180° cuts in nonstudded running shoes (RS) and in football shoes with natural (NTS) and synthetic turf studs (STS). Knee and ankle kinetic variables were analyzed with a 3 × 2 (shoe × movement) repeated-measures ANOVA (P < .05). A significant shoe-by-movement interaction was found in loading response peak knee adduction moments, with NTS producing smaller moments compared with both STS and RS only in 180° cuts. Reduced peak negative plantar flexor powers were also found in NTS compared with STS. The single-leg land cut produced greater loading response and push-off peak knee extensor moments, as well as peak negative and positive extensor and plantar flexor powers, but smaller loading peak knee adduction moments and push-off peak ankle eversion moments than 180° cuts. Overall, the STS and 180° cuts resulted in greater frontal plane knee loading and should be monitored for possible increased ACL injury risks.

Vise holds specimens for microscope

NASA Technical Reports Server (NTRS)

Greule, W. N.

1980-01-01

Convenient, miniature, spring-loaded clamp holds specimens for scanning electron microscope. Clamp is made out of nesting sections of studded angle-aluminum. Specimens are easier to mount and dismount with vise than with conductive adhesive or paint.

Non-monetary benefit indicators for prioritizing wetlands restoration projects

EPA Science Inventory

Ecological restoration of wetlands can reestablish ecosystem services that provide valuable social and environmental benefits. Explicitly characterizing these benefits can help managers better allocate scarce resources among potential restoration projects. Economic valuation stud...

Vehicle positioning trade study for ITS applications.

DOT National Transportation Integrated Search

2011-08-01

This report summarizes the results of a detailed positioning study intended to evaluate various positioning technologies and their applicability to a suite of location dependent vehicle safety and mobility applications. The initial phases of the stud...

Oil and gas impacts on transportation.

DOT National Transportation Integrated Search

2015-01-01

Colorados oil and gas industry is continually evolving, and there have been considerable changes in drilling techniques and geographic focus since the 2010 CDOT research study on Energy Development and the Transportation System. This research stud...

Use of micro unmanned aerial vehicles for roadside condition assessment

DOT National Transportation Integrated Search

2010-12-01

Micro unmanned aerial vehicles (MUAVs) that are equipped with digital imaging systems and global : positioning systems provide a potential opportunity for improving the effectiveness and safety of roadside : condition and inventory surveys. This stud...

Research on Vehicle-Based Driver Status/Performance Monitoring, Part III

DOT National Transportation Integrated Search

1996-09-01

A driver drowsiness detection/alarm/countermeasures system was specified, tested and evaluated, resulting in the development of revised algorithms for the detection of driver drowsiness. Previous algorithms were examined in a test and evaluation stud...

Inexpensive Bolt-Load Gage

NASA Technical Reports Server (NTRS)

Long, M. J.

1983-01-01

"Built-in" gage determines whether large bolt or stud has been torqued to desired load and provides for continuous inspection to ensure proper load is being maintained. Gage detects longitudinal stress/strain bolt; requires no electronic or sonic test equipment.

Star-Studded Strings around Cocoon Nebula

NASA Image and Video Library

2011-04-13

Dense filaments of gas in the IC5146 interstellar cloud can be seen clearly in this image taken in infrared light by the Herschel space observatory. The blue region is a stellar nursery known as the Cocoon nebula.

A Fatal Fad? Tongue Studs Cause More Problems Than Chipped Teeth

MedlinePlus

... a fatal infection, such as Ludwig's angina or endocarditis, according to a report in the May/June ... the airway or prevent the swallowing of saliva. Endocarditis occurs when bacteria travels into the bloodstream through ...

Air Traffic Control: Remote Radar For Grand Junction

DOT National Transportation Integrated Search

1996-11-01

In 1983, the Federal Aviation Administration (FAA) began a nationwide program : of consolidating air traffic control facilities to gain the benefits of : automation and any attendant cost savings. As part of this program, FAA : conducted several stud...

Army Reserve Component Personalized Empowerment Program (ARCPEP)

DTIC Science & Technology

2010-10-01

in U.S. hospitals—2007. Am J Health Syst Pharm 2008; 65:2244-64 2. Hardiker NR, Grant MJ. Barriers and facilitators that affect public engagement with eHealth services. Stud Health Technol Inform 2010; 160:13-7

Research On Vehicle-Based Driver Status/Performance Monitoring, Part I

DOT National Transportation Integrated Search

1996-09-01

A driver drowsiness detection/alarm/countermeasures system was specified, tested and evaluated, resulting in the development of revised algorithms for the detection of driver drowsiness. Previous algorithms were examined in a test and evaluation stud...

An organizational analysis of the Fulton Warehouse.

DOT National Transportation Integrated Search

1971-01-01

The purpose of this study was to examine the Warehouse organization as an entity separate from the Purchasing Division. The examination focused on the organization internally and then on its relationships to other organizational structures. This stud...

Construction of low-cost, Mod-OA wood composite wind turbine blades

NASA Technical Reports Server (NTRS)

Lark, R. F.

1983-01-01

Two sixty-foot, low-cost, wood composite blades for service on 200 kW Mod-OA wind turbines were constructed. The blades were constructed of epoxy resin-bonded Douglas fir veneers for the leading edge sections, and paper honeycombcored, birch plywood faced panels for the afterbody sections. The blades were joined to the wind turbine hub by epoxy resin-bonded steel load take-off studs embedded into the root end of the blades. The blades were installed on the 200 kW Mod-OA wind turbine facility at Kahuku, Hawaii, The blades completed nearly 8,000 hours of operation over an 18 month period at an average power of 150 kW prior to replacement with another set of wood composite blades. The blades were replaced because of a corrosion failure of the steel shank on one stud. Inspections showed that the wood composite structure remained in excellent condition.

Optimizing distance-based methods for large data sets

NASA Astrophysics Data System (ADS)

Scholl, Tobias; Brenner, Thomas

2015-10-01

Distance-based methods for measuring spatial concentration of industries have received an increasing popularity in the spatial econometrics community. However, a limiting factor for using these methods is their computational complexity since both their memory requirements and running times are in {{O}}(n^2). In this paper, we present an algorithm with constant memory requirements and shorter running time, enabling distance-based methods to deal with large data sets. We discuss three recent distance-based methods in spatial econometrics: the D&O-Index by Duranton and Overman (Rev Econ Stud 72(4):1077-1106, 2005), the M-function by Marcon and Puech (J Econ Geogr 10(5):745-762, 2010) and the Cluster-Index by Scholl and Brenner (Reg Stud (ahead-of-print):1-15, 2014). Finally, we present an alternative calculation for the latter index that allows the use of data sets with millions of firms.

Structural design of an in-line bolted joint for the space shuttle solid rocket motor case segments

NASA Technical Reports Server (NTRS)

Dorsey, John T.; Stein, Peter A.; Bush, Harold G.

1987-01-01

Results of a structural design study of an in-line bolted joint concept which can be used to assemble Space Shuttle Solid Rocket Motor (SRM) case segments are presented. Numerous parametric studies are performed to characterize the in-line bolted joint behavior as major design variables are altered, with the primary objective always being to keep the inside of the joint (where the O-rings are located) closed during the SRM firing. The resulting design has 180 1-inch studs, an eccentricity of -0.5 inch, a flange thickness of 3/4 inch, a bearing plate thickness of 1/4 inch, and the studs are subjected to a preload which is 70% of ultimate. The mass penalty per case segment joint for the in-line design is 346 lbm more than the weight penalty for the proposed capture tang fix.

Seroprevalence and factors associated with equine herpesvirus type 1 and 4 in Spanish Purebred horses in Spain.

PubMed

Cruz, F; Fores, P; Mughini-Gras, L; Ireland, J; Moreno, M A; Newton, J R

2016-04-16

Equine herpesvirus type 1 (EHV-1) and type 4 (EHV-4) have a worldwide distribution and cause respiratory disease, abortion, neonatal death and myeloencephalopathy in susceptible horses. Given the scarcity of serological EHV-1/EHV-4 data in Spain, the objective of this cross-sectional study was to estimate the seroprevalence of EHV-1/EHV-4 and to identify potential horse-level and stud farm-level factors associated with EHV-1/EHV-4 in the breeding Spanish Purebred (SP) horse population in central Spain. Serum samples from 334 SP unvaccinated horses, collected between September 2011 and November 2013 at 30 stud farms, were tested using a commercially available EHV-1/EHV-4 antibody ELISA and seroneutralisation as the World Organisation for Animal Health reference confirmation test. Data on factors putatively associated with seropositivity to EHV-1/EHV-4 were collected via a questionnaire and examined using logistic regression analysis. EHV-1/EHV-4 seroprevalence in the SP breeding population in central Spain, standardised for the sex distribution of the reference horse population, was 53.9 per cent (95 per cent confidence interval 44.0 per cent to 63.8 per cent). Increasing age, southern location of the stud farm, temperate climate during the summer, and a smaller surface area used for breeding activities in the farm were associated with increased odds for EHV-1/EHV-4 seropositivity, whereas EHV-1/EHV-4 vaccination of other resident horses and separation of breeding mares from youngsters were protective factors. British Veterinary Association.

Primary cooling check valve steam generator and loose parts events of November 1985

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1985-12-23

On November 10, 1985, a primary coolant check valve, CV-3-8, was opened for inspection. The valve flapper and mounting bracket were found to have become detached from the valve body and were resting in the bottom of the valve. Normally, the bracket is secured to the valve body with three studs and nuts. All three sets of studs, nuts and stud retainers were missing. As part of the effort to locate the missing valve parts, the primary side of the No. 2A steam generator was opened for inspection. Three cap screws and an associated locking bar used to secure certainmore » internals were found to be missing. In response, the Director, Reactor Engineering Department was assigned lead responsibility for developing and directing the implementation of a plan to correct deficiencies and ready the plant to return to operation. Next, a Special Safety Assessment Team was established to provide a structured assessment of the safety aspect of the component failures and the implications of such failures to other components in the primary coolant system. This structured assessment was to result in the development of an action plan that included the development of specific safety criteria, and identification and conduct of special investigations and analyses required for recovery from the event. Finally, an independent Management Review Team was created. The purpose of this report is to document the work of the Management Review Team, including the causal factors analyses, and various reviews required to support the recovery process.« less

Patient satisfaction and masticatory efficiency of single implant-retained mandibular overdentures using the stud and magnetic attachments.

PubMed

Cheng, Tao; Sun, Guifeng; Huo, Jingyu; He, Xiaoji; Wang, Yining; Ren, Yan-Fang

2012-11-01

To study patient satisfaction and masticatory efficiency of single implant-retained mandibular overdentures using the stud and magnetic attachments in a randomized clinical trial with a crossover design. Patients received a single implant placed in the midline of the mandible and either a stud (Locator) or a magnetic (Magfit) attachment, assigned at random. Patient satisfaction, including patient comfort, speech, chewing ability and retention, and masticatory efficiency measured by chewing peanuts, were assessed before and 3 months after attachment insertion. Patient satisfaction and masticatory efficiency were evaluated again 3 months after insertion of the alternate attachment bodies. The outcomes were compared before and after insertion of the attachments and between the two types of attachments using Wilcoxon signed rank tests. Patient overall satisfaction, comfort, speech, chewing ability, and retention improved significantly after insertion of both types of attachment bodies (p<0.05). Masticatory efficiencies also increased in both the Locator and the Magfit groups (p<0.05). There were no statistically significant differences in patient overall satisfaction, comfort, speech, and retention between the two types of attachments (p>0.05). The Locator attachments performed better in perceived chewing ability than the Magfit (p<0.05), but there was no statistically significant difference in masticatory efficiency between the two attachment types (p>0.05). Clinical outcomes were significantly improved in single implant-retained mandibular overdentures using either the Locator or the Magfit magnetic attachments. There was no difference in masticatory efficiency between the two attachment types. Copyright © 2012 Elsevier Ltd. All rights reserved.

CURRENT-USE PESTICIDES: ASSESSING EXPOSURE AND SPERMATOXICITY

EPA Science Inventory

We recently reported that higher levels of urinary metabolite (mercapturates) of the current-use pesticides alachlor, atrazine and diazinon were significantly associated with decreased semen quality in fertile men from mid-Missouri. The primary goal of this stud...

46. OFFICE INTERIOR FULL OF MACHINE PARTS, PAMPHLETS, AND ADVERTISEMENTS, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

46. OFFICE INTERIOR FULL OF MACHINE PARTS, PAMPHLETS, AND ADVERTISEMENTS, HARDWARE STORED IN SHELVES ALONG STUD WALLS-LOOKING WEST. - W. A. Young & Sons Foundry & Machine Shop, On Water Street along Monongahela River, Rices Landing, Greene County, PA

FUTURE SCENARIOS OF CHANGE IN WILDLIFE HABITAT

EPA Science Inventory

Studies in Pennsylvania, Iowa, California, and Oregon show varying losses of terrestrial wildlife habitat in scenarios based on different assumptions about future human land use patterns. Retrospective estimates of losses of habitat since Euro-American settlement in several stud...

A Preliminary Review of English Proficiency and Safe Commercial Motor Vehicle Operation.

DOT National Transportation Integrated Search

2008-07-01

Under sponsorship from the U.S. Department of Transportation Federal Motor Carrier Safety Administration, Office of Bus and Truck Standards and Operations, the John A. Volpe National Transportation Systems Center performed a preliminary research stud...

Abrasion-resistant concrete mix designs for precast bridge deck panels.

DOT National Transportation Integrated Search

2010-08-01

The report documents laboratory investigations undertaken to develop high performance concrete (HPC) for precast and pre-stressed bridge deck components that would reduce the life-cycle cost of bridges by improving the studded tire wear (abrasion) re...

Factors affecting prevalence and abundance of A.perfoliata infections in horses from south-eastern Poland.

PubMed

Tomczuk, Krzysztof; Grzybek, Maciej; Szczepaniak, Klaudiusz; Studzińska, Maria; Demkowska-Kutrzepa, Marta; Roczeń-Karczmarz, Monika; Abbass, Zahrai Abdulhammza; Kostro, Krzysztof; Junkuszew, Andrzej

2017-11-15

Equine Anoplocephalosis constitute a significant problem in horses worldwide. The aim of this study was to analyse intrinsic (host age and sex) and extrinsic (management type, pasture type and moisture) factors that influence the prevalence and FEC of A. perfoliata infections. Faecal samples were collected from 994 horses managed in studs or individually between 2012 and 2014. The Sedimentation-flotation method was applied for coproscopic analysis, and faecal egg counts were calculated. The overall prevalence was 25.1% (21.4-29.0) with the highest prevalence (36.1% [28.1-44.8]) found in horses 10-20 years old. The individuals kept in studs showed three times higher A. perfoliata prevalence compared to the ones managed individually. The prevalence significantly differed between pasture types, with individuals kept in studs (37.6% [34.3-40.9]) showing four times higher prevalence than horses kept individually (9.2% [4.8-16.5]). More horses kept on watery (42.0% [36.6-47.6]) and semi-watery (35.9% [31.3-40.7]) pastures were infected than those on dry (6.6% [4.6-9.2]) pastures. The overall A. perfoliata FEC in all examined individual was 2.67 and differed within sex, with mares showing 4.3 - times higher FEC of infection than stallions. Horses bred in studs (3.65±0.289) showed higher FEC than these bred individually (1.28±0.198). There was the effect of pasture type on A. perfoliata FEC, with horses kept on joint pastures (4.06±0.29) showing higher FEC than individuals kept individually (0.88±0.23). Pasture moisture significantly affected A. perfoliata FEC with the highest FECs in horses from watery pastures. Horses bred on dry pastures showed 16 times lower FEC than horses bred on watery pastures. Host age also significantly affected A. perfoliata FEC, with the oldest individuals showing the highest mean FEC. The presented analysis of intrinsic and extrinsic factors may help to overcome A. perfoliata infections in horses in different breeding systems. Understanding the role of management and pasture type risk factors that influence this parasitosis may benefit both breeders and veterinary surgeons. Copyright © 2017 Elsevier B.V. All rights reserved.

Evaluation of deterioration of structural concrete due to chloride intrusion and other damaging mechanisms.

DOT National Transportation Integrated Search

2015-09-01

Kentucky's bridges continue to age and experience distress. The intrusion of chlorides into : concrete remains the primary mechanism for deterioration. It leads to reinforcing steel corrosion : that damages the adjoining concrete structure. This stud...

Evaluation of thin overlays for bridge decks.

DOT National Transportation Integrated Search

2010-11-01

Eight thin polymer overlay systems were evaluated in the laboratory and on two bridge decks exposed to trucks and passenger vehicles including those with studded tires. The products were Mark 154, Flex-O-Lith, Safetrack HW, Kwik Bond PPC MLS, Tyregri...

Polyester polymer concrete overlay.

DOT National Transportation Integrated Search

2013-01-01

Polyester polymer concrete (PPC) was used in a trial application on a section of pavement that suffers from extensive studded tire wear. The purpose of the trial section is to determine if PPC is a possible repair strategy for this type of pavement d...

EXPERT SYSTEMS SHOW PROMISE FOR CUSTOMER INQUIRIES

EPA Science Inventory

This article describes results of an agreement between the North Penn Water Authority in Lansdale, Pa., and the US Environmental Protection Agency, Drinking Water Research Division, Cincinnati, Ohio, to study use of expert systems technology in a water utility. The threeyear stud...

Summer Transportation Institute 2001

DOT National Transportation Integrated Search

2002-04-01

The residential STI program was held at Lincoln University during July 9-August 3, 2001. Twenty students (nine 8th graders, 9th graders, and four 10th graders) participated in the program. One student was advised to withdraw after two weeks. The stud...

ULTRAFINE PARTICULATE MATTER EXPOSURE AUGMENTS ISCHEMIA REPERFUSION INJURY IN MICE

EPA Science Inventory

Epidemiological studies have linked ambient particulate matter (PM) levels to an increased incidence of adverse cardiovascular events. Yet little is definitively known about the mechanisms accounting for the cardiovascular events associated with PM-exposure. The goal of this stud...

Signaling hierarchy regulating human endothelial cell development

USDA-ARS?s Scientific Manuscript database

Our present knowledge of the regulation of mammalian endothelial cell differentiation has been largely derived from studies of mouse embryonic development. However, unique mechanisms and hierarchy of signals that govern human endothelial cell development are unknown and, thus, explored in these stud...

Research notes : thin polymer overlays on bridge decks.

DOT National Transportation Integrated Search

2007-11-01

Winters in Oregon are hard on our bridges. Vehicles with studded tires gouge the pavement and abrade the deck surface. This abrasion often leads to reduced skid resistance. As the bridge deck ages, cracks often develop. Deicing chemicals used in wint...

Weight of Evidence for Ecological Assessment

EPA Science Inventory

Systematic review (SR) and weight of evidence (WoE), both inform inferences based on multiple pieces of evidence, but they differ in their emphasis. Systematic reviews, such as those by Collaboration for Environmental Evidence, are assessments that emphasize the assembly of stud...

Total liquid routes and anti-icing liquids.

DOT National Transportation Integrated Search

2013-10-01

INDOT has successfully used salt brine in antiicing efforts as a way to deliver preventative treatment before an event (e.g. bridge deck : frost) occurs. In 2011 INDOT wanted to investigate the use of salt brine in deicing operations. This stud...

Evaluation of thin overlays for bridge decks.

DOT National Transportation Integrated Search

2009-11-01

Eight thin polymer overlay systems were evaluated in the laboratory and on two bridge decks exposed to trucks and passenger vehicles including those with studded tires. The products were Mark 154, Flex-O-Lith, Safetrack HW, Kwik Bond PPC MLS, Tyregri...

A TOOL FOR PLANNING AERIAL PHOTOGRAPHY

EPA Science Inventory

abstract The U.S. EPAs Pacific Coastal Ecology Branch has developed a tool in the form of an Excel. spreadsheet that facilitates planning aerial photography missions. The spreadsheet accepts various input parameters such as desired photo-scale and boundary coordinates of the stud...

The Research and Development of COM-PLY Lumber

Treesearch

Robert H. McAlister

1989-01-01

Between 1974 and 1986, a Southeastern Station Research Work Unit developed standards for composite studs, joists, and truss lumber and manufactured and demonstrated the materials. Economic feasibility was considered in every stage of research. Further development is left to industry.

Economic Analysis of Local Area Augmentation System and Alternative Architectures

DOT National Transportation Integrated Search

1996-01-01

The objective of this study has been to perform an economic comparison by conducting a cost-benefit analsyis (CBA) of the five Local Area Augementation System (LAAS) and alternative architectures. The five architectures chosen by the FAA for the stud...

Guidelines for Sampling, Assessing, and Restoring Defective Grout in Prestressed Concrete Bridge Post-Tensioning Ducts

DOT National Transportation Integrated Search

2013-05-01

This document is a technical summary of the Federal Highway Administration report, "Guidelines for Sampling, Assessing, and Restoring Defective Grout in Prestressed Concrete Bridge Post-Tensioning Ducts" (FHWA-HRT-13-028). The objectives of this stud...

Greener and Expeditious Synthesis of Bioactive Heterocycles using Microwave Irradiation

EPA Science Inventory

The utilization of green chemistry techniques is dramatically reducing chemical waste and reaction times as has recently been proven in several organic syntheses and chemical transformations. To illustrate these advantages in the synthesis of bio-active heterocycles, we have stud...

Assessing Transit Oriented Development Strategies with a New Combined Modal Split and Traffic Assignment Model

DOT National Transportation Integrated Search

2017-08-30

Transit oriented development (TOD) has emerged in recent years as a promising paradigm to promote public transportation, increase active transportation usage, mitigate congestion, and alleviate air pollution. However, there is a lack of analytic stud...

Metropolitan Transportation Management Center : a case study : Houston TranStar maximizing safety and mobility for the public

DOT National Transportation Integrated Search

1999-10-01

The following case study provides a snapshot of Houston's TranStar transportation management center. It follows the outline provided in the companion document, Metropolitan Transportation Management Center Concepts of Operation - A Cross Cutting Stud...

Genetics, genomics and fertility

USDA-ARS?s Scientific Manuscript database

In order to enhance the sustainability of dairy businesses, new management tools are needed to increase the fertility of dairy cattle. Genomic selection has been successfully used by AI studs to screen potential sires and significantly decrease the generation interval of bulls. Buoyed by the success...

All-wheel drive and winter-weather safety.

DOT National Transportation Integrated Search

2013-03-01

It is frequently stated that people living in northern states, the so called Snowbelt of the United : States, benefit with respect to safety from driving all-wheel or four-wheel drive vehicles as : opposed to front or rear-wheel drive only. This stud...

Morphological and genetic variation among sphaeralcea species

USDA-ARS?s Scientific Manuscript database

The herbaceous perennial species in the genus Sphaeralcea have desirable drought tolerance and aesthetics with potential for low-water use landscapes. However, taxonomy of these species is ambiguous, which leads to decreased consumer's confidence in the native plant industry. The goal of this stud...

Epigenetic supersimilarity of monozygotic twin pairs

USDA-ARS?s Scientific Manuscript database

Monozygotic twins have long been studied to estimate heritability and explore epigenetic influences on phenotypic variation. The phenotypic and epigenetic similarities of monozygotic twins have been assumed to be largely due to their genetic identity. Here, by analyzing data from a genome-scale stud...

Impacts of public policy on safety : graduated driver's license

DOT National Transportation Integrated Search

2008-12-01

This study evaluated the effectiveness of Missouris GDL policy. This study found a substantial decrease in crash involvement rates among drivers aged 15-18 in Missouri while drivers aged 19 or older have a moderate decrease in the rates. This stud...

An evaluation of the cost effectiveness of D-cracking preventive measures.

DOT National Transportation Integrated Search

2001-09-01

D-cracking has long been a serious problem in the deterioration of concrete pavements in severe weather climates. After much research, the mechanics and variables involved in the destructive forces of concrete D-cracking are becoming known. This stud...

Road dust emissions from paved roads measured using different mobile systems.

PubMed

Pirjola, Liisa; Johansson, Christer; Kupiainen, Kaarle; Stojiljkovic, Ana; Karlsson, Hans; Hussein, Tareq

2010-12-01

Very few real-world measurements of road dust suspension have been performed to date. This study compares two different techniques (referred to as Sniffer and Emma) to measure road dust emissions. The main differences between the systems are the construction of the inlet, different instruments for recording particulate matter (PM) levels, and different loads on the wheel axes (the weight of Sniffer was much higher than that of Emma). Both systems showed substantial small-scale variations of emission levels along the road, likely depending on-road surface conditions. The variations observed correlated quite well, and the discrepancies are likely a result of variations in dust load on the road surface perpendicular to the driving direction that cause variations in the measurements depending on slightly different paths driven by the two vehicles. Both systems showed a substantial influence on the emission levels depending on the type of tire used. The summer tire showed much lower suspension than the winter tires (one nonstudded and one studded). However, the relative importance of the nonstudded versus studded tire was rather different. For the ratio of studded/nonstudded, Emma shows higher values on all road sections compared with Sniffer. Both techniques showed increased emission levels with increasing vehicle speed. When the speed increased from 50 to 80 km hr(-1), the relative concentrations increased by 30-170% depending on the tire type and dust load. However, for road sections that were very dirty, Sniffer showed a much higher relative increase in the emission level with the nonstudded tire. Sniffer's absolute concentrations were mostly higher than Emma's. Possible reasons for the differences are discussed in the paper. Both systems can be used for studying relative road dust emissions and for designing air quality management strategies.

Difference in plantar pressure between the preferred and non‐preferred feet in four soccer‐related movements

PubMed Central

Wong, Pui‐lam; Chamari, Karim; Chaouachi, Anis; De Wei Mao; Wisløff, Ulrik; Hong, Youlian

2007-01-01

Objective and participants The present study measured the difference in plantar pressure between the preferred and non‐preferred foot in four soccer‐related movements in 15 male university soccer players (mean (SD) age 20.9 (1.3) years, mean (SD) height 173 (4) cm and mean (SD) weight 61.7 (3.6) kg). Design To record plantar pressure distribution, players randomly wore three types of soccer shoes (classical 6‐stud and 12‐stud, and specially designed 12‐stud) embedded with an insole pressure recorder device with 99 sensors, divided into 10 areas for analysis. Plantar pressure was recorded in five successful trials in each of the four soccer‐related movements: running (at 3.3 m/s), sideward cutting, 45° cutting and landing from a vertical jump. Results Plantar pressures of the preferred and non‐preferred foot were different in 115 of 120 comparisons. The overall plantar pressure of the preferred foot was higher than that of the non‐preferred foot. Specifically, in each of the four movements, higher pressure was found in the preferred foot during the take‐off phase, whereas this was found in the non‐preferred foot during the landing phase. This would suggest a tendency of the preferred foot for higher motion force and of the non‐preferred foot for a greater role in body stabilisation. Conclusions The data indicate that the preferred and non‐preferred foot should be treated independently with regard to strength/power training to avoid unnecessary injuries. Different shoes/insoles and different muscular strengthening programmes are thus suggested for each of the soccer player's feet. PMID:17138639

Effect of production management on semen quality during long-term storage in different European boar studs.

PubMed

Schulze, M; Kuster, C; Schäfer, J; Jung, M; Grossfeld, R

2018-03-01

The processing of ejaculates is a fundamental step for the fertilizing capacity of boar spermatozoa. The aim of the present study was to identify factors that affect quality of boar semen doses. The production process during 1 day of semen processing in 26 European boar studs was monitored. In each boar stud, nine to 19 randomly selected ejaculates from 372 Pietrain boars were analyzed for sperm motility, acrosome and plasma membrane integrity, mitochondrial activity and thermo-resistance (TRT). Each ejaculate was monitored for production time and temperature for each step in semen processing using the special programmed software SEQU (version 1.7, Minitüb, Tiefenbach, Germany). The dilution of ejaculates with a short-term extender was completed in one step in 10 AI centers (n = 135 ejaculates), in two steps in 11 AI centers (n = 158 ejaculates) and in three steps in five AI centers (n = 79 ejaculates). Results indicated there was a greater semen quality with one-step isothermal dilution compared with the multi-step dilution of AI semen doses (total motility TRT d7: 71.1 ± 19.2%, 64.6 ± 20.0%, 47.1 ± 27.1%; one-step compared with two-step compared with the three-step dilution; P < .05). There was a marked advantage when using the one-step isothermal dilution regarding time management, preservation suitability, stability and stress resistance. One-step dilution caused significant lower holding times of raw ejaculates and reduced the possible risk of making mistakes due to a lower number of processing steps. These results lead to refined recommendations for boar semen processing. Copyright © 2018 Elsevier B.V. All rights reserved.

Fatigue acceptance test limit criterion for larger diameter rolled thread fasteners

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kephart, A.R.

1997-05-01

This document describes a fatigue lifetime acceptance test criterion by which studs having rolled threads, larger than 1.0 inches in diameter, can be assured to meet minimum quality attributes associated with a controlled rolling process. This criterion is derived from a stress dependent, room temperature air fatigue database for test studs having a 0.625 inch diameter threads of Alloys X-750 HTH and direct aged 625. Anticipated fatigue lives of larger threads are based on thread root elastic stress concentration factors which increase with increasing thread diameters. Over the thread size range of interest, a 30% increase in notch stress ismore » equivalent to a factor of five (5X) reduction in fatigue life. The resulting diameter dependent fatigue acceptance criterion is normalized to the aerospace rolled thread acceptance standards for a 1.0 inch diameter, 0.125 inch pitch, Unified National thread with a controlled Root radius (UNR). Testing was conducted at a stress of 50% of the minimum specified material ultimate strength, 80 Ksi, and at a stress ratio (R) of 0.10. Limited test data for fastener diameters of 1.00 to 2.25 inches are compared to the acceptance criterion. Sensitivity of fatigue life of threads to test nut geometry variables was also shown to be dependent on notch stress conditions. Bearing surface concavity of the compression nuts and thread flank contact mismatch conditions can significantly affect the fastener fatigue life. Without improved controls these conditions could potentially provide misleading acceptance data. Alternate test nut geometry features are described and implemented in the rolled thread stud specification, MIL-DTL-24789(SH), to mitigate the potential effects on fatigue acceptance data.« less

The influence of antibiotic treatment of bitches in oestrus on their attractiveness to males during mating.

PubMed

Dziecioł, M; Nizański, W; Stańczyk, E; Kozdrowski, R; Najder-Kozdrowska, L; Twardoń, J

2013-01-01

The aim of this study was to evaluate the influence of the antibiotic treatment, including the mode of drugs administration, on bitches' attractiveness to the stud dogs during mating. Moreover, we tried to estimate the possibility of aversive effect of the drug vehicle on the male behavior. In experiment I, four bitches in oestrus without antibiotic treatment (group A), four bitches treated with intravaginal antibiotic (group B) and four bitches treated with intramuscular antibiotic (group C) were presented to four stud dogs. In experiment II, bitches in oestrus (n = 5) were presented to the males (n = 2) before and after the application to the females' vulva the antibiotic carrier--Miglyol 840 (Sasol, Germany). In both experiments the presence of the typical sexual behavior of the males (sniffing, licking the vulva and anal region, mating attempts) was evaluated. In experiment III the reaction of the males to the samples containing oestrual discharge from the bitches untreated and treated with antibiotics was evaluated. In the last part of study the aversion reaction to the samples containing antibiotic and the antibiotic carrier was evaluated. The results of experiments showed that females treated with the antibiotics were less attractive to males than untreated females, regardless of the method of administration. We did not observe adverse effect of the antibiotic carrier but samples from the bitches treated with antibiotics were significantly less attractive to the males. We concluded that the reason for reduced attractiveness of the bitches in oestrus after antibiotic treatment was the changes in semiochemical signal emitted by treated females as a consequence of elimination of the vaginal bacterial flora, which seems to be involved in creation of the typical, recognizable by the stud dogs, oestrual signal but also by the possible covering effect of used drugs.

Development of teaching material to integrate GT-POWER into combustion courses for IC engine simulations.

DOT National Transportation Integrated Search

2009-02-01

The main objective of this project was to develop instructional engineering projects that utilize the newly-offered PACE software GT-POWER for engine simulations in combustion-related courses at the Missouri University of Science and Technology. Stud...

Acylcarnitines: potential implications for skeletal muscle insulin resistance

USDA-ARS?s Scientific Manuscript database

Insulin resistance is linked to increased acylcarnitine species in a number of tissues including skeletal muscle, due to incomplete fatty acid oxidation (FAO). It is not known if acylcarnitines participate in muscle insulin resistance or simply reflect dysregulated metabolism. The aim of this stud...

PRELIMINARY DATABASE DEVELOPMENT IN TARGET DIETARY SAMPLES AND COMPOSITE DIET SAMPLES

EPA Science Inventory

Food may surpass drinking water as the major source of ingestion of total elemental arsenic for the general population. For this reason, accurate assessments of inorganic arsenic intake via food are needed to provide estimates for dietary exposure within future epidemiology stud...

Molecular basis for the thermostability of Newcastle disease virus

USDA-ARS?s Scientific Manuscript database

Thermostable Newcastle disease virus (NDV) vaccines have been used widely to protect village chickens against Newcastle disease, due to their decreased dependence on cold chain for transport and storage. However, the genetic basis underlying the NDV thermostability is poorly understood. In this stud...

Navigating "Thorny" Issues

ERIC Educational Resources Information Center

Hutchinson, Kashema; Gilbert, Aderinsola; Malyukova, Anna

2016-01-01

In their article "Mindfulness and discussing 'thorny' issues in the classroom" Konstantinos Alexakos et al. ("Cult Stud Sci Educ," 2016. doi: 10.1007/s11422-015-9718-0) describe "thorny" issues as "difficult topics to discuss because they are more personal to some perhaps even cause pain and violence." As…

Performance of Steel Stud Walls Subjected to Blast Loads

DTIC Science & Technology

2010-02-01

be used as load-bearing components or non-load-bearing components, and a variety of exterior finishes and internal sheathing may be used. From an...common sheathing materials such as drywall , oriented strand board (OSB), stucco, etc., utilizing conventional structural connections (e.g., slip

38. VIEW SOUTHWEST OF STREET LEVEL IN SHOWROOM ADDITION (NOW ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

38. VIEW SOUTHWEST OF STREET LEVEL IN SHOWROOM ADDITION (NOW USED AS FINISHING ROOM) WITH FRESHLY PAINTED DORY BOATS ON DISPLAY. 2X4 STUD WALL AND ROOF FRAMING CAN BE SEEN. - Lowell's Boat Shop, 459 Main Street, Amesbury, Essex County, MA

Effects of lighting and time of day on the locomotion of zebrafish larvae.

EPA Science Inventory

The increasing use of zebrafish in developmental research highlights the need for detailed behavioral investigations in this species. Behavior represents the unique interface between the intrinsic and extrinsic forces that determine an organism’s health and survival. We have stud...

Development of a Mixture Design Procedure for Stone Matrix Asphalt

DOT National Transportation Integrated Search

1997-03-01

Stone Matrix Asphalt (SMA) has been used successfully in Europe for over 20 : years to provide better rutting resistance and to resist studded tire wear. : Since 1991, the use of SMA has increased steadily in the United States. At : present, some sta...

An evaluation of the cost effectiveness of D-cracking preventive measures : executive summary.

DOT National Transportation Integrated Search

2001-09-01

D-cracking has long been a serious problem in the deterioration of concrete pavements in severe weather climates. After much research, the mechanics and variables involved in the destructive forces of concrete D-cracking are becoming known. This stud...

Fabrication of low-cost Mod-OA wood composite wind turbine blades

NASA Technical Reports Server (NTRS)

Lark, R. F.; Gougeon, M.; Thomas, G.; Zuteck, M.

1983-01-01

The wood composite blades were fabricated by using epoxy resin-bonded laminates of Douglas fir veneers for the leading edge spar sections and honeycomb-cored birch plywood panels for the blade trailing edge or afterbody sections. The blade was joined to the wind turbine hub assembly by epoxy resin-bonded steel load take-off studs. The wood composite blades were installed in the Mod-OA wind turbine test facility at Kahuku, Hawaii. The wood composite blades have successfully completed high power (average of 150 kW) operations for an eighteen month period (nearly 8,000 hr) before replacement with another set of wood composite blades. The original set of blades was taken out of service because of the failure of the shank on one stud. An inspection of the blades at NASA-Lewis showed that the shank failure was caused by a high stress concentration at a corrosion pit on the shank fillet radius which resulted in fatigue stresses in excess of the endurance limit.

AN IN SILICO INVESTIGATION OF THE ENANTIOSELECTIVE METABOLISM RATES OF TRIAZOLE FUGICIDES

EPA Science Inventory

The objective of this work is to use in silico methods such as ab initio quantum and classical force-field methods to explore and develop an understanding for the enantioselective metabolism rates experimentally observed in the triazole fungicide bromuconazole. This directed stud...

CLIMATE CHANGE IN THAILAND AND ITS POTENTIAL IMPACT ON RICE YIELD

EPA Science Inventory

Because of the uncertainties surrounding prediction of climate change, it is common to employ climate scenarios to estimate its impacts on a system. Climate scenarios are sets of climatic perturbations used with models to test system sensitivity to projected changes. In this stud...

Speaking of Reading.

ERIC Educational Resources Information Center

Rosenthal, Nadine

Written in the tradition of Studs Terkel, this book presents oral histories of 77 diverse readers (from avid to infrequent readers) about how reading affects their lives. Sprinkled throughout the book are narratives of nationally recognized personalities, such as Maxine Hong-Kingston, Robert MacNeil, Gloria Steinem, Linus Pauling, Julie Harris,…

18. DETAIL OF EXTERIOR WALL CONSTRUCTION, VIEW TOWARD EAST, THIRD ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

18. DETAIL OF EXTERIOR WALL CONSTRUCTION, VIEW TOWARD EAST, THIRD BAY Showing furring strips, kraft faced cellulose fiber insulation, and asphalt felt applied to interior of exterior wall studs. - U.S. Military Academy, Ice House, Mills Road at Howze Place, West Point, Orange County, NY

Field-based evaluation of a male-specific (F+) RNA coliphage concentration method

EPA Science Inventory

Fecal contamination of water poses a significant risk to public health due to the potential presence of pathogens, including enteric viruses. Thus, sensitive, reliable and easy to use methods for the detection of microorganisms are needed to evaluate water quality. In this stud...

Trap height affects capture of lady beetles (Coleoptera: Coccinellidae) in pecan orchards

USDA-ARS?s Scientific Manuscript database

There is scarce information regarding the vertical stratification of predaceous Coccinellidae in tall trees. Although numerous studies have been done in orchards and forests, very few studies have assessed the occurrence of predaceous Coccinellidae high in tree canopies. The objective of this stud...

LIVE CELL IMAGING OF THE OXIDATIVE EFFECTS OF EXPOSURE TO AN ORGANIC PM COMPONENT

EPA Science Inventory

RATIONALE. Exposure to ambient particulate matter (PM) has been associated with adverse health effects, including inflammatory responses in the lung. Diesel exhaust particles (DEP) are a ubiquitous contributor of the fine and ultrafine PM burden in ambient air. Toxicological stud...

Population diversity of Diaphorina citri (Hemiptera: Liviidae) in China based on whole mitochondrial genome sequences

USDA-ARS?s Scientific Manuscript database

BACKGROUND: Diaphorina citri (Asian citrus psyllid, ACP) transmits “Candidatus Liberibacter asiaticus”, an unculturable alpha-proteobacterium associated with citrus Huanglongbing (HLB). ACP has been reported in 11 provinces/regions in China, yet its population diversity remains unclear. In this stud...

Attenuation of Marek's disease virus by codon pair deoptimization of a core gene

USDA-ARS?s Scientific Manuscript database

Marek’s disease virus (MDV) is an oncogenic alphaherpesvirus of Gallus gallus, the domesticated chicken. Control strategies rely upon comprehensive vaccination in ovo with live attenuated virus vaccines consisting of antigenically similar avian herpesviruses or attenuated strains of MDV. Recent stud...

Determining Spatial Variability in PM2.5 Source Impacts across Detroit, MI

EPA Science Inventory

Intra-urban variability in air pollution source impacts was investigated using receptor modeling of daily speciated PM_2.5 measurements collected at residential outdoor locations across Detroit, MI (Wayne County) as part of the Detroit Exposure and Aerosol Research Stud...

Retrospective and statistical analysis of breeding management on the Italian Heavy Draught Horse breed.

PubMed

Mantovani, R; Sartori, C; Pigozzi, G

2013-07-01

This study investigated some aspects of breeding management in the Italian Heavy Draught Horse breed, aiming at improving its efficiency at stud farm level. A first aim was to evaluate the risk of unsuccessful reproduction in mares after an early (3 years) or normal (4 years) age at first foaling, in interaction with different stud rearing systems. A second objective was the examination of the mean time length in which young 2-year-old stallions maintain a genetic superiority on older proven stallions, identifying a 'genetic lifespan' in which young stallions can be safely used for reducing the cost of services. Reproductive performance at first and second foaling of 1513 mares were used. Mares had a normal first foal at 3 (n = 745) or 4 years of age (n = 768) in stud farms on the basis of stable (n = 488), feral (n = 345) or semi-feral (n = 680) rearing systems. Logistic regression analysis was performed by modeling the risk of unsuccessful reproduction in the subsequent season (i.e., results at second foaling), as affected by the interaction of age at first foaling × rearing system (six classes). Genetic lifespan of young stallions was estimated by regressing the least square means from a mixed model analysis for repeated measures of individual differences in 'total merit' estimated breeding values (EBVs) between young stallions (mean no. of 45/year) and the mean EBV of all proven stallions in a given year of genetic evaluation (mean no. of 483/year). Young stallions born between 1999 and 2005 were used, following each generation (i.e., birth year) from 2 to 7 subsequent yearly genetic evaluations. In comparison with the best reproductive success of second foaling at 4 years in stable systems, the greatest risk of unsuccessful reproduction was at 3 years in feral (+167%) and 3 years in semi-feral conditions (+91%). Young stallions showed a 0.50 s.d. greater EBV at the first evaluation than proven stallions, with a mean annual decrease in EBV of 0.07 s.d./year on proven stallions. Optimal breeding management could be obtained in stud farms by limiting foaling at 3 years, particularly in feral and semi-feral rearing systems, and using young stallions for 3 to 4 years to maintain a perceptible selection differential with older proven stallions and to reduce cost of services. Later, the selection differential with proven stallions become less consistent and genetic improvement could be slowed down.

Light-Frame Wall Systems: Performance and Predictability.

Treesearch

David S. Gromala

1983-01-01

This paper compares results of all wall tests with analytical predictions of performance.Conventional wood-stud walls of one configuration failed at bending loads that were 4 to 6 times design load.The computer model overpredicted wall strength by and average of 10 percent and deflection by an average of 6 percent.

26 CFR 1.1251-2 - Excess deductions account.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., and livestock used in the trade or business of farming which is held for draft, breeding, dairy, or... $13,000 (b) Gain from disposition of breeding herd to which section 1251(c)(1) applies (computed... include all expenditures paid or incurred for producing the animal, such as for stud, breeding, and...

Unitized Nut-and-Washer Assembly

NASA Technical Reports Server (NTRS)

Rossi, P. J.

1986-01-01

Combination nut, washer, and lockwasher secures parts quickly without damaging metal finishes. Nut and lockwasher are captured by bent tabs of flat washer in this concept for unified fastener. Optional perforated tab on flat washer allows easy tagging and storage. Fastener intended for attaching leads and buses to studs on electronic equipment.

ARSENIC REMOVAL FROM DRINKING WATER BY ION EXCHANGE AND ACTIVATED ALUMINA PLANTS

EPA Science Inventory

This report documents a long term performance study of two ion exchange (IE) and two activated alumina (AA) treatment plants to remove arsenic from drinking water. Performance information was collected on these systems that are located in the northeast for one full year. The stud...

Dechlorination Kinetics Of Monochlorobiphenyls By Fe/Pd: Effects Of Solvent, Temperature, And PCB Concentration

EPA Science Inventory

Well-known, yet undefined, changes in the conditions and activity of palladized zerovalent iron (Fe/Pd) over an extended period of time hindered a careful study of dechlorination kinetics in long-term experiments. A short-term experimental method was, therefore, developed to stud...

CpG methylation differences between neurons and glia are highly conserved from mouse to human

USDA-ARS?s Scientific Manuscript database

Understanding epigenetic differences that distinguish neurons and glia is of fundamental importance to the nascent field of neuroepigenetics. A recent study used genome-wide bisulfite sequencing to survey differences in DNA methylation between these two cell types, in both humans and mice. That stud...

Assembly room, bunkhouse first floor interior. Vent pipe for missing ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Assembly room, bunkhouse first floor interior. Vent pipe for missing heating stove exited through opening into chimney, seen on the far wall. Walls are exposed studs and bracing with board and battan on the exterior and interior sides. - Sespe Ranch, Bunkhouse, 2896 Telegraph Road, Fillmore, Ventura County, CA

Liver receptor homolog-1 is a critical determinant of methyl-pool metabolism

USDA-ARS?s Scientific Manuscript database

Balance of labile methyl groups (choline, methionine, betaine, and folate) is important for normal liver function. Quantitatively, a significant use of labile methyl groups is in the production of phosphatidylcholines (PCs), which are ligands for the nuclear liver receptor homolog-1 (LRH-1). We stud...

Influence of site and soil properties on the DRIFT spectra of northern cold-region soils

USDA-ARS?s Scientific Manuscript database

We investigated the influence of site characteristics and soil properties on the chemical composition of organic matter in soils collected from a latitudinal transect across Alaska through analysis of diffuse reflectance infrared Fourier transform mid infrared (MidIR) spectra of bulk soils. The stud...

Effects of Watershed Land Use and Geomorphology on Stream Baseflows in the Southern Blue Ridge Mountains

EPA Science Inventory

The current understanding of watershed hydrology does not provide insight into prediction of low-flow response to land-use change in developing regions like the Blue Ridge of north Georgia and western North Carolina. To address this problem, three separate but complementary stud...

29 CFR 1926.754 - Structural steel assembly.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 8 2010-07-01 2010-07-01 false Structural steel assembly. 1926.754 Section 1926.754 Labor... (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Steel Erection § 1926.754 Structural steel...) Tripping hazards. Shear connectors (such as headed steel studs, steel bars or steel lugs), reinforcing bars...

29 CFR 1926.754 - Structural steel assembly.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 29 Labor 8 2011-07-01 2011-07-01 false Structural steel assembly. 1926.754 Section 1926.754 Labor... (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Steel Erection § 1926.754 Structural steel...) Tripping hazards. Shear connectors (such as headed steel studs, steel bars or steel lugs), reinforcing bars...

Polybrominated Diphenyl Ether (DE-71)Interferes with Thyroid Hormone Action Independent Of Effects On Circulating Levels of Thyroid Hormone in Male Rats

EPA Science Inventory

Polybrominated diphenyl ethers (PBDEs) are routinely found in human tissues including cord blood and breast milk. PBDEs may interfere with thyroid hormone (TH) during development, which could produce neurobehavioral deficits. An assumption in experimental and epidemiological stud...

PARTICLE DEPOSITION IN SPONTANEOUSLY HYPERTENSIVE (SH) RATS EXPOSED VIA WHOLE-BODY INHALATION: MEASURED VS. ESTIMATED DOSE.

EPA Science Inventory

It has been well documented by epidemiological studies that exposure to elevated levels of ambient particulate matter (PM) can lead to adverse health outcomes, including cardiopulmonary-related morbidity and mortality. As a result of these findings, many animal toxicological stud...

DOING Physics--Physics Activities for Groups.

ERIC Educational Resources Information Center

Zwicker, Earl, Ed.

1985-01-01

Shows how an electric stud finder (available from hardware stores for $15-20) is used to detect changes in capacitance produced by changes in thickness of a medium or in dielectric constant. Also describes how to construct an inexpensive motor from a battery, rubber bands, ceramic magnet, and copper wire. (DH)

USE OF MULTI-PHOTON LASER-SCANNING MICROSCOPY TO DESCRIBE THE DISTRIBUTION OF XENOBIOTIC CHEMICALS IN FISH EARLY LIFE STAGES

EPA Science Inventory

To better understand the mechanisms by which persistent bioaccumulative toxicants (PBTs) produce toxicity during fish early life stages (ELS), dose response relationships need to be determined in relation to the dynamic distribution of chemicals in sensitive tissues. In this stud...

An Expert Study of a Descriptive Model of Teacher Communities

ERIC Educational Resources Information Center

Admiraal, Wilfried; Lockhorst, Ditte; van der Pol, Jakko

2012-01-01

Teachers in secondary education mainly feel responsibility for their own classroom practice, resulting in largely autonomous and isolated work and private learning activities. Most teachers teach separate classes behind closed doors and learn about teaching by teaching, often described as trial and error (Hodkinson and Hodkinson in Stud Continuing…

(Dis)connections between Specific Language Impairment and Dyslexia in Chinese

ERIC Educational Resources Information Center

Wong, Anita M.-Y.; Ho, Connie S.-H.; Au, Terry K.-F.; Kidd, Joanna C.; Ng, Ashley K.-H.; Yip, Lesley P.-W.; Lam, Catherine C.-C.

2015-01-01

Specific language impairment (SLI) and dyslexia are found to co-occur in school-aged children learning Chinese, a non-alphabetic language (Wong, Kidd, Ho, & Au in "Sci Stud Read" 14:30--57, 2010). This paper examined the "Distinct" hypothesis--that SLI and dyslexia have different cognitive deficits and behavioural…

Impulse radar studfinder

DOEpatents

McEwan, Thomas E.

1995-01-01

An impulse radar studfinder propagates electromagnetic pulses and detects reflected pulses from a fixed range. Unmodulated pulses, about 200 ps wide, are emitted. A large number of reflected pulses are sampled and averaged. Background reflections are subtracted. Reflections from wall studs or other hidden objects are detected and displayed using light emitting diodes.

Exploring Ways to Improve DTAG Deployment Success Rates with the ARTS Pneumatic Launcher

DTIC Science & Technology

2011-09-30

spring, four springs, no spring), and a different shock absorber system has been developed, (the giraffe leg technique or GL, Figure 2), which has...GL ( giraffe leg technique) with 3 studs (right) WORK COMPLETED During the testing period various dummy whale targets were constructed for

Cesar Chavez--Grade Ten Model Curriculum and Resources.

ERIC Educational Resources Information Center

California State Dept. of Education, Sacramento.

In this California state curriculum model for grade 10, "World History, Culture, and Geography: The Modern World," students stud the life, work, and philosophy of Cesar E. Chavez. The students learn about the historical developments of many of the ideas and philosophy of Chavez, particularly the evolution of democratic principles.…

46 CFR 56.70-1 - General.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., Assembly and Erection § 56.70-1 General. (a) The following generally applies to all types of welding, such as stud welding, casting repair welding and all processes of fabrication welding. Where the detailed requirements are not appropriate to a particular process, alternatives must be approved by the Marine Safety...

Impulse radar studfinder

DOEpatents

McEwan, T.E.

1995-10-10

An impulse radar studfinder propagates electromagnetic pulses and detects reflected pulses from a fixed range. Unmodulated pulses, about 200 ps wide, are emitted. A large number of reflected pulses are sampled and averaged. Background reflections are subtracted. Reflections from wall studs or other hidden objects are detected and displayed using light emitting diodes. 9 figs.

Dynamic Nature of Alterations in the Endocrine System of Fathead Minnows Exposed to the Fungicide Prochloraz, Presentation

EPA Science Inventory

The vertebrate hypothalamic-pituitary-gonadal (HPG) axis is controlled through various feedback mechanisms that ideally serve to maintain a dynamic homeostasis of the system in the face of changing environmental conditions, including exposure to chemical stressors. In these stud...

Effects of buffer strips and grazing management on soil loss from pastures

USDA-ARS?s Scientific Manuscript database

Intensive grazing pressure can cause soil erosion from pastures causing increased sediment loading to aquatic systems. The objectives of this work were to determine the long-term effects of grazing management and buffer strips on soil erosion from pastures fertilized with broiler litter. Field stud...

Gimme Shelter!: Doghouse Project Hones Construction Skills

ERIC Educational Resources Information Center

Shackelford, Ray; Griffis, Kurt

2007-01-01

In Rover's House project, students practice planning, measurement, layout, and processing skills in building a doghouse. The project is more than a doghouse--it is a learning activity that helps students develop and enhance their ability to work with reinforced concrete, steel and wood studs, trusses, roofing materials and a variety of…

Determination of metabolic resistance mechanisms in pyrethroid-resistant and fipronil-tolerant brown dog ticks

USDA-ARS?s Scientific Manuscript database

Rhipicephalus sanguineus (Latreille) (Ixodida: Ixodidae) is a three-host dog tick found worldwide that is able to complete its’ entire lifecycle indoors. Options for the management of R. sanguineus are limited and its’ control relies largely on only a few acaricidal active ingredients. Previous stud...

Development of a 96-well plate iodine binding assay for amylose content determination

USDA-ARS?s Scientific Manuscript database

Cereal starch amylose/amylopectin (AM/AP) ratios are critical in functional properties for food and industrial applications. Conventional methods for the determination of AM/AP of cereal starches are very time consuming and labor intensive making it very difficult to screen large sample sets. Stud...

Effect of intermittent versus daily calorie restriction on changes in weight and patient reported outcomes in people with multiple sclerosis

USDA-ARS?s Scientific Manuscript database

An intermittent fasting or calorie restriction diet has favorable effects in the mouse forms of multiple sclerosis (MS) and may provide additional anti-inflammatory and neuroprotective advantages beyond benefits obtained from weight loss alone. We conducted a pilot randomized controlled feeding stud...

Influence of pH on the Transport of Silver Nanoparticles in Saturated Porous Media: Laboratory Experiments and Modeling

EPA Science Inventory

Given the ubiquity of silver nanoparticles (AgNPs), the largest and fastest growing category of nanomaterials, and their potential for toxic effects to both humans and the environment, it is important to understand their environmental fate and transport. The purpose of this stud...

Consolidation of materials by pulse-discharge processes

NASA Astrophysics Data System (ADS)

Strizhakov, E. L.; Nescoromniy, S. V.

2017-07-01

The article presents the research and the analysis of the pulse-discharge processes of capacitor discharge sintering: CD Stud Welding, capacitor discharge percussion welding (CDPW), high-voltage capacitor welding with an inductive-dynamic drive (HVCW with IDD), pulse electric current sintering (PECS) of powders. The comparative analysis of the impact parameter is presented.

78 FR 76815 - Steel Threaded Rod From India: Preliminary Affirmative Countervailing Duty Determination and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-19

... DEPARTMENT OF COMMERCE International Trade Administration [C-533-856] Steel Threaded Rod From... exporters of steel threaded rod from India. The period of investigation (``POI'') is January 1, 2012... this investigation is steel threaded rod. Steel threaded rod is certain threaded rod, bar, or studs, of...

Whole wheat bread: Effect of bran fractions on dough and end-product quality

USDA-ARS?s Scientific Manuscript database

Consumption of whole-wheat based products is encouraged due to its important nutritional elements that beneficial to human health. However, processing of whole-wheat based products, such as whole-wheat bread, results in poor end-product quality. Bran was postulated as the major problem. In this stud...

Concept for southern pine plantation operation in the year 2020

Treesearch

P. Koch

1980-01-01

Fertilization, close spacing, very early thinning, and application of new harvesting and manufacturing technology could yield- over a 35-year rotation - 146 tons per acre (ovendry basis) of pulp, 2-by-4 studs, random-length conventional lumber, millwork and structural laminated wood, long-wide structural lumber laminated from veneer, sheathing plywood, structural...

26 CFR 1.1251-2 - Excess deductions account.

Code of Federal Regulations, 2011 CFR

2011-04-01

... business of farming which is held for draft, breeding, dairy, or sporting purposes regardless of the period... of breeding herd to which section 1251(c)(1) applies (computed before applying limitation) 14,000 (c... animal, such as for stud, breeding, and veterinary services, as well as all amounts paid or incurred with...

26 CFR 1.1251-2 - Excess deductions account.

Code of Federal Regulations, 2014 CFR

2014-04-01

... business of farming which is held for draft, breeding, dairy, or sporting purposes regardless of the period... of breeding herd to which section 1251(c)(1) applies (computed before applying limitation) 14,000 (c... animal, such as for stud, breeding, and veterinary services, as well as all amounts paid or incurred with...

26 CFR 1.1251-2 - Excess deductions account.

Code of Federal Regulations, 2013 CFR

2013-04-01

... business of farming which is held for draft, breeding, dairy, or sporting purposes regardless of the period... of breeding herd to which section 1251(c)(1) applies (computed before applying limitation) 14,000 (c... animal, such as for stud, breeding, and veterinary services, as well as all amounts paid or incurred with...

26 CFR 1.1251-2 - Excess deductions account.

Code of Federal Regulations, 2012 CFR

2012-04-01

... business of farming which is held for draft, breeding, dairy, or sporting purposes regardless of the period... of breeding herd to which section 1251(c)(1) applies (computed before applying limitation) 14,000 (c... animal, such as for stud, breeding, and veterinary services, as well as all amounts paid or incurred with...

Ganymede - Mixture of Terrains and Large Impact Crater in Uruk Sulcus Region

NASA Image and Video Library

1997-09-07

A mixture of terrains studded with a large impact crater is shown in this view of the Uruk Sulcus region of Jupiter moon Ganymede taken by NASA Galileo spacecraft during its first flyby of the planet-sized moon on June 27, 1996. http://photojournal.jpl.nasa.gov/catalog/PIA00280

Gratitude, R"essentiment," and Citizenship Education

ERIC Educational Resources Information Center

Jonas, Mark E.

2012-01-01

Patricia White ("Stud Philos Educ" 18:43-52, 1999) argues that the virtue gratitude is essential to a flourishing democracy because it helps foster universal and reciprocal amity between citizens. Citizens who participate in this reciprocal relationship ought to be encouraged to recognize that "much that people do does in fact help to make…

19. DETAIL OF INTERIOR WALL CONSTRUCTION, VIEW TOWARD SOUTH, THIRD ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

19. DETAIL OF INTERIOR WALL CONSTRUCTION, VIEW TOWARD SOUTH, THIRD BAY Showing asphalt felt applied to both sides of interior wall studs beneath wood cladding. Back-nailing of felt indicates sequence of felt and cladding installation. - U.S. Military Academy, Ice House, Mills Road at Howze Place, West Point, Orange County, NY

Specification for the Performance, Design, Development and Test Requirements of a Magnetic Tape Cartridge Replay Machine.

DTIC Science & Technology

1983-11-23

fixing screws, bolts , pins, studs , switches, indicators and other protruding components shall be protected from accidental damage by guards or shields...active-low TTL- compatible signals which shall enter the CRM through a multipin conector . Equipment to generate those signals is not described by this

Country-level net primary production distribution and response to drought and land cover change

USDA-ARS?s Scientific Manuscript database

Carbon sequestration by terrestrial ecosystems can offset emissions and thereby offers an alternative way of achieving the target of reducing the concentration of CO2 in the atmosphere. Net primary production (NPP) is the first step in the sequestration of carbon by terrestrial ecosystems. This stud...

Prevention of obesity relatred metabolic diseases by processed foods containing soluble dietary fibers and flavonoids (abstract)

USDA-ARS?s Scientific Manuscript database

Asians and other non-caucasians are generally more susceptible to obesity related chronic diseases such as type 2 diabetes and cardiovascular disease. Viscous soluble dietary fibers such as cereal beta-glucans and psyllium reduce plasma cholesterol and postprandial glycemia in humans. We have stud...

Large-scale confirmatory tests of a phytosanitary irradiation treatment against Sternochetus frigidus (F.) in Philippine mango

USDA-ARS?s Scientific Manuscript database

The mango pulp weevil, Sternochetus frigidus (F.) is an important quarantine pest preventing the export of mangoes from the Philippines to the United States and other countries. Previously, a radiation dose of 100 Gy was proposed for phytosanitary treatment of S. frigidus based on dose-response stud...

Class, Identity, and Teacher Education

ERIC Educational Resources Information Center

Van Galen, Jane A.

2010-01-01

This paper explores the possibilities of working with White, working-class teacher education students to explore the "complex social trajectory" (Reay in Women's Stud Int Forum 20(2):225-233, 1997a, p. 19) of class border crossing as they progress through college. Through analysis of a course that I have developed, "Education and the American…

The GED and the Rise of Contextless Accountability

ERIC Educational Resources Information Center

Hutt, Ethan

2014-01-01

Background/Context:Policy discussions in the U.S. and abroad have become increasingly studded with reference to the results of international tests like PISA. Unlike most assessments, PISA is not designed to measure whether students have mastered a particular school curriculum but rather provide a measure of students' ability to meet future…

75 FR 27409 - Airworthiness Directives; Sikorsky Aircraft Corporation (Sikorsky) Model S-92A Helicopters

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-17

... gearbox (MGB) filter bowl assembly with a two-piece MGB filter bowl assembly and replacing the existing mounting studs. The AD also requires inspecting the MGB lube system filters, the housing, the housing... prompted by tests indicating that an existing MGB filter bowl assembly can fail under certain loading...

[Application of thermosetting plastics to eliminate undercuts].

PubMed

Bielawski, T

1989-01-01

The author proposes to utilize the properties of thermosetting plastics used in other fields to use them in prosthetics in order to eliminate undercuts. Application of extra equipment in claspograph in the form of studs of three dimension makes formation of undercuts' blockade easier improving the result of work at the same time.

Bovine leukemia virus seroprevalence among cattle presented for slaughter in the United States

USDA-ARS?s Scientific Manuscript database

Infection with bovine leukemia virus (BLV) results in economic loss due reduced productivity, especially the reduction of milk production and early culling. In the USA.,USA, previous studies in 1996, 1999 and 2007 showed BLV infections widespread, especially in the dairy herds. The goal of this stud...

13. VIEW OF AREAWAY 104 LOOKING SOUTHEAST, TOWARD ANIMAL QUARTERS. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

13. VIEW OF AREAWAY 104 LOOKING SOUTHEAST, TOWARD ANIMAL QUARTERS. WOOD STUD WALL WITH WIRE MESH INFILL HAS BEEN ADDED. HORIZONTAL WOOD PANELING ON WALLS IS PAINTED. FLOOR IS CONCRETE SLAB. - Presidio of San Francisco, Cavalry Stables, Cowles Street, between Lincoln Boulevard & McDowell Street, San Francisco, San Francisco County, CA

Iron bioavailability studies of the first generation of iron-biofortified beans released in Rwanda

USDA-ARS?s Scientific Manuscript database

This paper represents a series of in vitro Fe bioavailability experiments, Fe content analysis and polyphenolic profile of the first generation of Fe biofortified beans (Phaseolus vulgaris) selected for human trials in Rwanda and released to farmers of that region. The objective of the present stud...

Situating Race in College Students' Search for Purpose and Meaning: Who Am I?

ERIC Educational Resources Information Center

Watt, Sherry K.

2015-01-01

People in the U.S. live in a racialized society whereby life experiences, economic opportunities, social relationships, and psychological rewards hinge upon a racial hierarchy that benefits Whites and often disadvantages other races. Studs Terkel once referred to race as "An American Obsession." Therefore, it is near impossible to…

Genome-wide association study of heat tolerance of developing leaves during vegetative growth stages in a sorghum association panel

USDA-ARS?s Scientific Manuscript database

Heat stress reduces grain yield and quality worldwide. Enhancing heat tolerance of crops is one of the essential strategies required for sustaining agricultural production, especially as frequent temperature extremes escalates due to climate change. Although heat tolerance mechanisms have been stud...

Exploring Ways to Improve DTAG Deployment Success Rates With the ARTS Pneumatic Launcher

DTIC Science & Technology

2010-01-01

absorber system has been developed, (the giraffe leg technique or GL, Figure 2), which has the shock absorbing component in front of the tag. The ARTS...3 Figure 2: the new 1- and 4-spring shock absorbing robot (left) and the GL ( giraffe leg technique) with 3 studs (right) WORK

Biology and natural enemies of Agrilus fleischeri (Coleoptera:Buprestidae), a newly emerging destructive buprestid pest in Northeast China

USDA-ARS?s Scientific Manuscript database

The jewel beetle Agrilus fleischeri Obenberger (Coleoptera: Buprestidae) is a newly emerging major pest of poplar trees (Populus spp.) in northeast China and is responsible for the poplar mortality throughout its distribution range. In order to determine how to manage this pest effectively, we stud...

Science and Creationism: A Response to Kenneth Tobin

ERIC Educational Resources Information Center

Alexakos, Konstantinos

2009-01-01

In his December editorial on Michael Reiss, Kenneth Tobin ("Cult Stud Sci Educ" 3:793-798, 2008), raises some very important questions for science and science teachers regarding science education and the teaching of creationism in the classroom. I agree with him that students' creationist ideologies should be treated not as misconceptions but as…

Incidence, species and antimicrobial resistance of naturally occurring Campylobacter isolates from quail carcasses sampled in a commercial processing facility

USDA-ARS?s Scientific Manuscript database

Most of the published information about the presence of Campylobacter on processed poultry is from studies with chickens and turkeys; therefore there is a paucity of published material about the presence of Campylobacter on commercially processed quail (Coturnix coturnix). The objective of this stud...

Appraising Lexical Bundles in Mathematics Classroom Discourse: Obligation and Choice

ERIC Educational Resources Information Center

Herbel-Eisenmann, Beth; Wagner, David

2010-01-01

Working from a large corpus of transcripts from secondary mathematics classrooms, we identify patterns of speech that encode interpersonal positioning. We extend our analysis from a previous article (Herbel-Eisenmann, Wagner & Cortes, Educ Stud Math, 2010, in press), in which we introduced a concept from corpus linguistics--a "lexical bundle,"…

Reconceptualising the "Behavioural Approach" in Agricultural Studies: A Socio-Psychological Perspective

ERIC Educational Resources Information Center

Burton, Rob J. F.

2004-01-01

In rural studies the "behavioural approach", i.e. an actor-oriented, largely questionnaire-based methodology that focuses ''on the motives, values and attitudes that determine the decision-making processes of individual farmers'' (J. Rural Stud 11 (1995) 51, p. 55), has become increasingly important in the investigation of farmer response to…

Sound transmission of cavity walls due to structure borne transmission via point and line connections.

PubMed

Davy, John L

2012-08-01

The author has published equations for predicting the air borne sound transmission of double leaf cavity walls due to the structure borne sound transmission across the air cavity via (possibly resilient) line connections, but has never published the full derivation of these equations. The author also derived equations for the case when the connections are rigid point connections but has never used them or published them or their derivations. This paper will present the full derivation of the author's theory of the air borne sound transmission of double leaf cavity walls due to the structure borne sound transmission across the air cavity via point or line connections which are modeled as four pole networks. The theoretical results will be compared with experimental results on wooden stud cavity walls from the National Research Council of Canada because the screw spacing is given for these results. This enables connections via studs and screws to be modeled as point connections and avoids the need to make any assumptions about the compliance of the equivalent point or line connections.

The effects of aluminum oxide on inertial welding of aluminum in space applications

NASA Astrophysics Data System (ADS)

Smith, Michael H.

1992-05-01

Inertial friction welding of 2219 aluminum alloy studs to 2219 aluminum alloy plates is investigated in air and in an argon atmosphere to determine the effects of an intact oxide layer on weld quality. Scratch-brushing of plates and studs was performed in an argon atmosphere to break up the oxide layer and prevent reformation prior to testing. Argon was used to simulate the near-oxygen free space environment. Weld quality was determined by a bend test and by measurement of the fraction of the weld surface area that was dimpled in appearance following fracture of the weld. The fundamental theories of friction and wear that are applicable to friction welding are reviewed. A brief survey of current welding methods that may have application in space is presented, as well as a discussion of their feasibility and limitations. Characteristics of the space station are discussed as well as their consequences on welding in space. A qualitative model of the process of inertial friction welding based on the theories of friction and observations of welds and weld fractures is developed and presented.

Experimental Study on Welded Headed Studs Used In Steel Plate-Concrete Composite Structures Compared with Contactless Method of Measuring Displacement

NASA Astrophysics Data System (ADS)

Kisała, Dawid; Tekieli, Marcin

2017-10-01

Steel plate-concrete composite structures are a new innovative design concept in which a thin steel plate is attached to the reinforced concrete beam by means of welded headed studs. The comparison between experimental studies and theoretical analysis of this type of structures shows that their behaviour is dependent on the load-slip relationship of the shear connectors used to ensure sufficient bond between the concrete and steel parts of the structure. The aim of this paper is to describe an experimental study on headed studs used in steel plate-concrete composite structures. Push-out tests were carried out to investigate the behaviour of shear connectors. The test specimens were prepared according to standard push-out tests, however, instead of I-beam, a steel plate 16 mm thick was used to better reflect the conditions in the real structure. The test specimens were produced in two batches using concrete with significantly different compressive strength. The experimental study was carried out on twelve specimens. Besides the traditional measurements based on LVDT sensors, optical measurements based on the digital image correlation method (DIC) and pattern tracking methods were used. DIC is a full-field contactless optical method for measuring displacements in experimental testing, based on the correlation of the digital images taken during test execution. With respect to conventional methods, optical measurements offer a wider scope of results and can give more information about the material or construction behaviour during the test. The ultimate load capacity and load-slip curves obtained from the experiments were compared with the values calculated based on Eurocodes, American and Chinese design specifications. It was observed that the use of the relationships developed for the traditional steel-concrete composite structures is justified in the case of ultimate load capacity of shear connectors in steel plate-concrete composite structures.

Feasibility of Steel Fiber-Reinforced Rubberized Concrete in Cold Regions for High Volume Intersections

NASA Astrophysics Data System (ADS)

Abou Eid, Mahear A.

There are many challenges faced with the use of Portland Cement Concrete (PCC) in cold regions, but with the inclusion of new technologies such as steel fibers and recycled tire crumb rubber efficient construction may be possible. Research was conducted on a modified concrete material that included both steel fibers and crumb rubber. The composite material was called Steel Fiber-Reinforced Rubberized Concrete (SFRRC). The objective of this investigation was to provide evidence showing that SFRRC can reduce tire rutting compared to asphaltic pavement. In addition, the research showed that the SFRRC could withstand freeze-thaw cycles and increase service life of roadways. Several tests were performed to determine the characteristics of the material. Freeze-thaw testing was performed to determine compressive strength loss and visual deterioration of the material. Wheel tracker rut testing was performed both with the standard steel wheel and with a modified studded rubber tire to determine plastic deformation and rut resistance. An experimental test slab was cast in place on a public approach to observe the construction procedures, the effects of studded tire wear and the frost actions in cold region conditions. Based on freeze-thaw and wheel tracker test results and observations of the experimental test slab, the SFRRC material shows viability in cold regions for resisting freeze-thaw actions. The freeze-thaw testing resulted in increased compressive strength after 300 freeze-thaw cycles and very low deterioration of material compared to standard PCC. The wheel tracker testing resulted in very low plastic deformation and minor material rutting with use of the studded rubber tire. The test slab showed very minor surface wear, no freeze-thaw cracking and no rutting after one winter of use. It is recommended that further testing of the material be conducted by means of a large-scale trial section. This would provide information with respect to cost analysis and integration of the material into the Department of Transportation construction program.

Field investigations of bacterial contaminants and their effects on extended porcine semen.

PubMed

Althouse, G C; Kuster, C E; Clark, S G; Weisiger, R M

2000-03-15

Field investigations (n=23) were made over a 3-yr period at North American boar studs and farms in which the primary complaint was sperm agglutination in association with decreased sperm longevity of extended semen, and increased regular returns to estrus and/or vaginal discharges across parity. Microscopic examination of extended semen from these units revealed depressed gross motility (usually <30%), sperm agglutination, and sperm cell death occurring within 2 d of semen collection and processing regardless of the semen extender used. The extended semen exhibited a high number of induced acrosome abnormalities (>20%). Sample pH was acidic (5.7 to 6.4) in 93% of the submitted samples. Aerobic culture yielded a variety of bacteria from different genera. A single bacterial contaminant was obtained from 66% of the submitted samples (n=37 doses); 34% contained 2 or more different bacterial genera. The most frequently isolated contaminant bacteria from porcine extended semen were Alcaligenes xylosoxydans (n=3), Burkholderia cepacia (n=6), Enterobacter cloacae (n=6), Escherichia coli (n=6), Serratia marcescens (n=5), and Stenotrophomonas [Xanthomonas] maltophilia (n=6); these 6 bacteria accounted for 71% of all contaminated samples, and were spermicidal when re-inoculated and incubated in fresh, high quality extended semen. All contaminant bacteria were found to be resistant to the aminoglycoside gentamicin, a common preservative antibiotic used in commercial porcine semen extenders. Eleven genera were spermicidal in conjunction with an acidic environment, while 2 strains (E. coli, S. maltophilia) were spermicidal without this characteristic acidic environment. Bacteria originated from multiple sources at the stud/farm, and were of animal and nonanimal origin. A minimum contamination technique (MCT) protocol was developed to standardize hygiene and sanitation. This protocol focused on MCT's during boar preparation, semen collection, semen processing and laboratory sanitation. Implementation of the MCT, in addition to specific recommendations in stud management, resulted in the control of bacterial contamination in the extended semen.

SUPERFUND TREATABILITY CLEARINGHOUSE: ABSTRACT ON-SITE INCINERATION TESTING OF SHIRCO INFRARED SYSTEMS PORTABLE DEMONSTRATION UNIT-CONTAMINATED SOILS TREATABILITY STUDY

EPA Science Inventory

In August of 1986, Shirco was contracted by Dekonta GmbH, a Vest German hazardous waste treatment company, to perform treatability studies at one of the largest dioxin-contaminated sites in the world. The Shirco Infrared process was selected by Dekonta after a two year stud...

Re-Inhabiting Place in Contemporary Rural Communities: Moving toward a Critical Pedagogy of Place

ERIC Educational Resources Information Center

Huffling, Lacey D.; Carlone, Heidi B.; Benavides, Aerin

2017-01-01

Heather Zimmerman and Jennifer Weible's ("Cult Stud Sci Educ," 2016) use of place-based pedagogy in high school science education honors their participants' lived experiences and the rural communities from which they come. They raise an unresolved tension in their findings: Why did the youth in their study, who clearly learned a lot…

Prevalence of equine Piroplasmosis and its association with tick infestation in the State of Sao Paulo, Brazil

USDA-ARS?s Scientific Manuscript database

Serum samples were collected from 582 horses from 40 stud farms in the State of São Paulo and tick (Acari: Ixodidae) infestations were evaluated on them. Serum samples were subjected to the complement fixation test (CFT) and a competitive inhibition ELISA (cELISA) for Babesia caballi and Theileria e...

Arabidopsis sodium dependent and independent phenotypes triggered by H+-PPase up-regulation are SOS1 dependent

USDA-ARS?s Scientific Manuscript database

The goal of the study and research was to coordinate regulation of transporters at both the plasma membrane and vacuole contribute to plant cell’s ability to adapt to a changing environment and play a key role in the maintenance of the chemiosmotic circuits required for cellular growth. In this stud...

17. DETAIL OF INTERIOR AND EXTERIOR WALL CONSTRUCTION, VIEW TOWARD ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

17. DETAIL OF INTERIOR AND EXTERIOR WALL CONSTRUCTION, VIEW TOWARD NORTHEAST CORNER, THIRD BAY Showing insulated exterior wall at right; asphalt felt on interior separation wall at left; sill beam, stud, and concrete foundation detailing of interior wall. - U.S. Military Academy, Ice House, Mills Road at Howze Place, West Point, Orange County, NY

Transcriptomic Analysis of Host Immune Response in the Skin of Chickens Infected with Marek's Disease Virus

USDA-ARS?s Scientific Manuscript database

Marek’s disease virus, a highly cell-associated oncogenic 'alpha-herpesvirus, is the causative agent of a T cell lymphoma and neuropathic disease called Marek’s disease. The skin is the only anatomical site where infectious enveloped cell-free virions are produced and shed into the environment. Stud...

Least-cost control of agricultural nutrient contributions to the Gulf of Mexico hypoxic zone

USDA-ARS?s Scientific Manuscript database

In 2007, the hypoxic zone in the Gulf of Mexico, measuring 20,720 km**2, was one of the two largest reported since measurement of the zone began in 1985. The extent of the hypoxic zone is related to nitrogen and phosphorous loadings originating on agricultural fields in the upper Midwest. This stud...

Daily dietary selenium intake and hair selenium content in a high selenium area of Enshi, China

USDA-ARS?s Scientific Manuscript database

Selenium is essential to humans and is widely distributed within the human body. Its content in blood, urine, hair and nails are important indicators to evaluate Se level in the human body. In China (Shadi, Enschi city), human selenosis of residents is reported to occur in high numbers. In this stud...

Using copper oxide wire particles or sericea lespedeza to prevent a peri-parturient rise of gastrointestinal nematodes in sheep and goats

USDA-ARS?s Scientific Manuscript database

Gastrointestinal nematodes (GIN) continue to plague the small ruminant industry, especially parts of the world with warm, humid climates. Alternatives to chemicals are needed for GIN control because of anthelmintic resistance of GIN and a desire to reduce chemical residues in meat products. A stud...

75 FR 4308 - Airworthiness Directives; Sikorsky Aircraft Corporation (Sikorsky) Model S-92A Helicopters

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-27

... the Sikorsky Model S-92A helicopters. The AD would require replacing the main gearbox (MGB) filter bowl assembly with a two-piece MGB filter bowl assembly and replacing the existing mounting studs. The AD would also require inspecting the MGB lube system filters, the housing, the housing threads, and...

Analyzing NPS Scheduling Using OSIRIS

DTIC Science & Technology

1993-03-01

School TEACHER SCHEDULE BLOCKS REPORT Date: 2/19/93 Period Name ID Term Days 1234 Adragna , Joe 170401 1 F xx Agrawal, Brij 120101 1 F xx Almquist...LOAD REPORT Date: 3/18/93 Total Max Consec Total Teacher ID Term Classes Classes Stud Adragna , Joe 170401 1 1 1 3 Agrawal, Brij 120101 1 2 2 98 Aiello

33 CFR 154.810 - Vapor line connections.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., and (ii) The middle yellow band 0.8 meter (2.64 feet) wide; and (2) Labeled “VAPOR” in black letters.... The stud must be located at the top of the flange, midway between bolt holes, and in line with the bolt hole pattern. (d) Each hose used for transferring vapors must: (1) Have a design burst pressure of...

Comparison of trout hepatocytes and liver S9 fractions as in vitro models for predicting hepatic clearance in fish

EPA Science Inventory

Isolated hepatocytes and liver S9 fractions have been used to collect in vitro biotransformation data for fish as a means of improving modeled estimates of chemical bioaccumulation. To date, however, there have been few direct comparisons of these two methods. In the present stud...

Genome-Wide association mapping of loci associated with plant growth and forage production under salt stress in alfalfa (Medicago sativa L.)

USDA-ARS?s Scientific Manuscript database

Salinity tolerance is highly desirable to sustain alfalfa production in marginal lands that have been rendered saline. In this study, we used a diverse panel of alfalfa accessions for mapping loci associated with plant growth and forage production under salt stress using genome-wide association stud...

Quantitative trait loci underlying seed sugars content in MD96-5722 by spencer recombinant inbred line population of soybean

USDA-ARS?s Scientific Manuscript database

Sucrose, raffinose, and stachyose are important soluble sugars in soybean [Glycine max (L.) Merr.] seeds, and soybean seeds with higher sucrose and lower raffinose and stachyose are desirable. Therefore, optimizing sugars biosynthesis is a major goal for soy food industry. The objective of this stud...

The Relationship between Intrinsic Motivation and Academic Achievement for First Generation Latino College Students

ERIC Educational Resources Information Center

Trevino, Naomi Noel; DeFreitas, Stacie Craft

2014-01-01

Hispanic students are pursuing higher education more than in previous years and they often represent their family as the first member to attend college (Strage in "Coll Stud J" 33:198-205, 1999). Past educational research has studied the influence of intrinsic motivation on academic achievement in various ethnically diverse elementary,…

33 CFR 154.810 - Vapor line connections.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., and (ii) The middle yellow band 0.8 meter (2.64 feet) wide; and (2) Labeled “VAPOR” in black letters.... The stud must be located at the top of the flange, midway between bolt holes, and in line with the bolt hole pattern. (d) Each hose used for transferring vapors must: (1) Have a design burst pressure of...

33 CFR 154.810 - Vapor line connections.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., and (ii) The middle yellow band 0.8 meter (2.64 feet) wide; and (2) Labeled “VAPOR” in black letters.... The stud must be located at the top of the flange, midway between bolt holes, and in line with the bolt hole pattern. (d) Each hose used for transferring vapors must: (1) Have a design burst pressure of...

Expanding the Conversation: Further Explorations into Indigenous Environmental Science Education Theory, Research, and Practice

ERIC Educational Resources Information Center

Lowan, Greg

2012-01-01

Indigenous environmental science education is a diverse, dynamic, and rapidly expanding field of research, theory, and practice. This article highlights, challenges, and expands upon key areas of discussion presented by Mack et al. (Cult Stud Sci Educ 7, "2012") as part of the forum on their article "Effective Practices for Creating…

Hygrothermal Anaylsis of Wood-Frame Wall Assemblies in a Mixed-Humid Climate

Treesearch

Samuel V. Glass

2013-01-01

This study uses a one-dimensional hygrothermal model to investigate the moisture performance of 10 residential wood-frame wall assemblies in a representative mixed-humid climate location of Baltimore, Maryland (climate zone 4A). All the assemblies include oriented strandboard (OSB) sheathing and vinyl siding. The walls differ in stud cavity thickness, level of cavity...

Psychometric Analysis of the Orientations to Happiness Questionnaire in Taiwanese Undergraduate Students

ERIC Educational Resources Information Center

Chen, Lung Hung; Tsai, Ying-Mei; Chen, Mei-Yen

2010-01-01

The aim of this study was to examine the psychometric properties of the Orientations to Happiness Questionnaire (OHQ; Peterson et al. in "J Happiness Stud" 6(1):25-41, 2005) in Taiwanese students. The participants were 578 undergraduate students (M[subscript age] = 18.64, SD = 1.02) and completed the OHQ, satisfaction with life scale…

Characteristics of growing media mixes and application for open-field production of strawberry (Fragaria ananassa)

USDA-ARS?s Scientific Manuscript database

Pathogen-free growing media are widely used for strawberry production in protected structures in Europe but not common in the United States. There is a need to investigate the feasibility of producing strawberry fruits in open fields with the pathogen-free media in the U.S. The objective of the stud...

Curiosity Didn't Kill This Cat: Studs Terkel for English Language Learners

ERIC Educational Resources Information Center

Kelly, Susan

2010-01-01

After years of studying academic English, many students are ready to move beyond language designed for the classroom, or what Yoshida (2001) calls "fishbowl" English, to the language of the "open sea." As students develop beyond the beginner level, they are ready to read and discuss appropriate authentic texts. Even students who are unsure of…

Evaluation of mixed hardwood studs manufactured by the Saw-Dry-Rip (SDR) process

Treesearch

R. R. Maeglin; R. S. Boone

1985-01-01

This paper describes increment cores (a useful tool in forestry and wood technology) and their uses which include age determination, growth increment, specific gravity determination, fiber length measurements, fibril angle measurements, cell measurements, and pathological investigations. Also described is the use and care of the increment borer which is essential in...

Tool for Guiding An Auger

NASA Technical Reports Server (NTRS)

Wesselski, C. J.

1983-01-01

Auger and Ram have same pitch, which minimizes damage to workpiece and load carried by auger. Auger firmly fastened onto ram shaft by screw and kept from rotating on shaft by slot machined into end of stem and male driving lug that engages slot. Used to install threaded studs in plastic or rubber where impractical to mold them in.

Pythian Powerhouse and Laundry: Historic Building Survey

DTIC Science & Technology

2008-08-01

14 4. Wall and ceiling finish ...second floor are poured concrete. The flooring on the first floor is wood. 4. Wall and Ceiling Finish : The inside of the exterior walls are...left as ex- posed cut limestone; however, several coats of paint or sealant have been added (Photo 38). The bathroom walls are wood stud with drywall

Use of Precast Concrete Walls for Blast Protection of Steel Stud Construction Preprint

DTIC Science & Technology

2007-11-01

Side Elevation Front Elevation Front Elevation Side Elevation a) Sandwich Wall b) Solid Wall I I---6’-10" " 11.. Exterior Face - Form finish 2------C...damage to the interior drywall was visible. The instnunentation consisted of three external reflected pressure gages at the front face of the test

The school nutrition program's role in weight management of 4th grade elementary students

USDA-ARS?s Scientific Manuscript database

We are attempting to uncover the school nutrition program's role in weight management of 4th grade elementary students. Data was collected within a time frame for the food frequency questionnaire (FFQ) set at two months at the WT Cheney Elementary School and South Wood Elementary for 4th grade stud...

Proceedings of a Workshop on Cognitive Testing Methodology (11-12 June 1984)

DTIC Science & Technology

1986-01-01

Becker , and G.E. Handlemann. 1979. Hippocampus, space, and memory. Behav. Brain Sci. 2:313-365. Osbourne, D.P., E.R. Brown, and C.T. Randt. 1982...the B complex. J. Appl. Psychol. 30:359-379. Chernorutskii, M.V. 1943. Problem of alimentary dystrophy . Stud. Lenirg:ad Physicians 3:3-13. Cited in A

Apparatus For Eddy-Current Inspection Of Bolts

NASA Technical Reports Server (NTRS)

Amos, Jay M.

1994-01-01

Eddy-current apparatus for inspection of bolts, studs, and other threaded fasteners detects flaws in threads, shanks, and head fillets. With help of apparatus, technician quickly inspects fasteners of various dimensions. Accommodates fasteners with diameters from 0.190 in. to 1 in. and with lengths up to 5 in. Basic design modified to accommodate fasteners of other sizes.

Studded tire wear resistance of PCC pavements with special mix design : contract 6620, I-90, Argonne Road to Sullivan Road, MP 286.91 to 292.38

DOT National Transportation Integrated Search

2011-02-01

The performance of portland cement concrete mixes with higher flexural strength, higher cement content, and with Hard-Cem additive, carpet drag finish, and tined finish were evaluated over a period of five years to determine their resistance to studd...

Determination of differences in crop injury from aerial application of glyphosate using vegetation indices and geostatistics

USDA-ARS?s Scientific Manuscript database

Injury to crops caused by off-target drift of glyphosate can seriously reduce growth and yield, and is of great concern to farmers and aerial applicators. Determining an indirect method for assessing the levels and extent of crop injury could support management decisions. The objectives of this stud...

Neuroethology: self-recognition helps octopuses avoid entanglement.

PubMed

Crook, Robyn J; Walters, Edgar T

2014-06-02

How an octopus performs complex movements of its eight sucker-studded arms without entanglement has been a mystery. A new study has found that self-recognition of the octopus's skin by its suckers inhibits reflexive grasping of its own arms, simplifying the mechanisms needed to generate intricate arm behavior. Copyright © 2014 Elsevier Ltd. All rights reserved.

Exploring the Significance of Resource-Rich Views in Science Education

ERIC Educational Resources Information Center

Siry, Christina

2011-01-01

In a recently published article in Cultural Studies of Science Education (Volume 6, Issue 2) titled, "What does playing cards have to do with science? A resource-rich view of African American young men", Alfred Schademan (Cult Stud Sci Educ 6:361-380, "2011") examines the resources that African American young men learn through playing a card came…

Some Geometric Inequalities Relating to an Interior Point in Triangle

ERIC Educational Resources Information Center

Wu, Yu-Dong; Zhang, Zhi-Hua; Liang, Chun-Lei

2010-01-01

In this short note, by using one of Li and Liu's theorems [K.-H. Li, "The solution of CIQ. 39," "Commun. Stud. Inequal." 11(1) (2004), p. 162 (in Chinese)], "s-R-r" method, Cauchy's inequality and the theory of convex function, we solve some geometric inequalities conjectures relating to an interior point in triangle. (Contains 1 figure.)

Mexican Immigrant Transnational Social Capital and Class Transformation: Examining the Role of Peer Mediation in Insurgent Science

ERIC Educational Resources Information Center

Bruna, Katherine Richardson

2010-01-01

In this article, I return to the interactions of Augusto and his teacher in an "English Learner Science" classroom in a demographically-transitioning US Midwest community (Richardson Bruna and Vann in Cult Stud Sci Educ 2:19-59, "2007") and further engage a class-first perspective to achieve two main conceptual objectives.…

Economic feasibility of products from inland West small-diameter timber

Treesearch

Spelter Henry; Rong Wang; Peter Ince

1996-01-01

A large part of the forests located in the Rocky Mountain region of the U.S. West (inland West) is characterized by densely packed, small-diameter stands. The purpose of this study was to examine the economic feasibility of using small-diameter material from this resource to manufacture various wood products: oriented strandboard (OSB), stud lumber, random-length...

Comparison of brown sugar, hot water, and salt methods for detecting western cherry fruit fly (Diptera: Tephritidae) larvae in sweet cherry

USDA-ARS?s Scientific Manuscript database

Brown sugar or hot water methods have been developed to detect larvae of tephritid fruit flies in post-harvest fruit in order to maintain quarantine security. It would be useful to determine if variations of these methods can yield better results and if less expensive alternatives exist. This stud...

Early development of mixed-species studs on the Wayne Nation Forest

Treesearch

Eric R. Norland; Dr. David M. Hix

1993-01-01

The species compositions of many upland hardwood forests in southeastern Ohio appear to be changing. Since the arrival of settlers, most of the mixed mesophytic forest has been cleared at least once as a result of timber cutting, burning, and agriculture. The compositions of the second- and third-growth forests are shifting toward a smaller component of oaks (...

Changes in product recovery between live and dead lodgepole pine: a compendium.

Treesearch

Thomas D. Fahey; Thomas A. Snellgrove; Marlin E. Plank

1986-01-01

Six studies were used to compare differences in recovery of volume and value among live, recent dead, and older dead lodgepole pine (Pinus contorts Dougl. ex Loud.) in the Western United States. The products studied included boards, random-length dimension, studs, and veneer. For the average size log (12 cubic feet) absolute values were highest for boards, followed by...

Lumber recovery from insect-killed lodgepole pine in the northern Rocky Mountains.

Treesearch

Marlin E. Plank

1984-01-01

A total of 496 logs from lodgepole pine (Pinus contorts Dougl. ex Loud.) trees killed by the mountain pine beetle (Dendroctonus ponderosae Hopk.) were compared with 189 logs from similar live trees. Logs were processed through a stud mill. In most cases lumber recovery from trees dead 1 to 3 years was the same as that from live...

Education in Chile. Bulletin, 1945, No. 10

ERIC Educational Resources Information Center

Ebaugh, Cameron D.

1945-01-01

Chile is a republic 2,630 miles long, extending along the western coast of South America from Peru to the southernmost tip of the continent. In width it averages about 110 miles, with snow-capped, volcano-studded Andes in the East, a low coastal range along the Pacific and a string of valleys and plains in between. It is estimated that 5,000…

Student Perceptions of Effective Instruction and the Development of Critical Thinking: A Replication and Extension

ERIC Educational Resources Information Center

Loes, Chad N.; Salisbury, Mark H.; Pascarella, Ernest T.

2015-01-01

This study utilized data from the Wabash National Study of Liberal Arts Education to test the robustness of research conducted by Pascarella et al. ("J Coll Stud Dev" 37:7-19, 1996) that explored the relationship between student perceptions of exposure to organized and clear instruction and growth in critical thinking skills among…

Profile 2003: softwood sawmills in the United States and Canada

Treesearch

Henry Spelter; Matthew Alderman

2003-01-01

About 160 fewer softwood sawmills are operating in the United States and Canada than were 8 years ago. Nevertheless, the combined capacity of the remaining mills has increased by 16%, to over 173 million cubic meters. Of the approximately 1,140 mills, about 470 characterize their output as dimension lumber, accounting for 67% of capacity; 136 list studs as their...

Prevalence of coliforms, Salmonella, Listeria, and Campylobacter associated with eggs and the environment of conventional cage and free range egg production

USDA-ARS?s Scientific Manuscript database

There is a desired by US consumers for eggs produced by hens in alternative production systems. As the retail shell egg market offers these products to accommodate consumer demands, additional information is needed to ensure processing methodologies result in safe eggs from all egg sources. A stud...

Relative effects of human and feral hog disturbance on a wet forest in Hawaii

Treesearch

C. John Ralph; Bruce D. Maxwell

1984-01-01

The effects of 20 months of intensive disturbance by humans, as well as the presence of feral hogs Sus scrofa, was measured on vegetation. Both forms of disturbance have been thought severely to affect Hawaiian rain forests by reduction of plant cover and allowing the proliferation of exotic plants. Despite much human use throughout the stud), area,...

Firebrand Production from Building Components Fitted with Siding Treatments

PubMed Central

Suzuki, Sayaka; Manzello, Samuel L.

2016-01-01

Firebrand production from real-scale building components under well-controlled laboratory conditions was investigated. Re-entrant corner assemblies were ignited and during the combustion process, firebrands were collected to determine the size/mass distribution generated from such real-scale building components under varying wind speed. In prior work, a unique ignition methodology was developed to generate firebrands from re-entrant corner assemblies constructed of wood studs and oriented strand board (OSB). In this study, this ignition methodology was applied to re-entrant corners constructed from wood studs/OSB but fitted with actual siding treatments (tar paper and cedar siding) to determine the influence of siding treatments on firebrand generation from wall assemblies. Firebrands were collected with pans filled with water, and then the size and mass of firebrands were measured after drying. The size and mass distributions of firebrands collected in this study were compared with the data from prior component tests as well as the limited studies available in the literature on this topic. Some firebrands were found to be lighter for a given projected area than others, likely produced from cedar siding or tar paper. The effects of applied siding treatments on firebrand production are discussed in detail. PMID:27114643

Firebrand Production from Building Components Fitted with Siding Treatments.

PubMed

Suzuki, Sayaka; Manzello, Samuel L

2016-02-01

Firebrand production from real-scale building components under well-controlled laboratory conditions was investigated. Re-entrant corner assemblies were ignited and during the combustion process, firebrands were collected to determine the size/mass distribution generated from such real-scale building components under varying wind speed. In prior work, a unique ignition methodology was developed to generate firebrands from re-entrant corner assemblies constructed of wood studs and oriented strand board (OSB). In this study, this ignition methodology was applied to re-entrant corners constructed from wood studs/OSB but fitted with actual siding treatments (tar paper and cedar siding) to determine the influence of siding treatments on firebrand generation from wall assemblies. Firebrands were collected with pans filled with water, and then the size and mass of firebrands were measured after drying. The size and mass distributions of firebrands collected in this study were compared with the data from prior component tests as well as the limited studies available in the literature on this topic. Some firebrands were found to be lighter for a given projected area than others, likely produced from cedar siding or tar paper. The effects of applied siding treatments on firebrand production are discussed in detail.

How do typically developing deaf children and deaf children with autism spectrum disorder use the face when comprehending emotional facial expressions in British sign language?

PubMed

Denmark, Tanya; Atkinson, Joanna; Campbell, Ruth; Swettenham, John

2014-10-01

Facial expressions in sign language carry a variety of communicative features. While emotion can modulate a spoken utterance through changes in intonation, duration and intensity, in sign language specific facial expressions presented concurrently with a manual sign perform this function. When deaf adult signers cannot see facial features, their ability to judge emotion in a signed utterance is impaired (Reilly et al. in Sign Lang Stud 75:113-118, 1992). We examined the role of the face in the comprehension of emotion in sign language in a group of typically developing (TD) deaf children and in a group of deaf children with autism spectrum disorder (ASD). We replicated Reilly et al.'s (Sign Lang Stud 75:113-118, 1992) adult results in the TD deaf signing children, confirming the importance of the face in understanding emotion in sign language. The ASD group performed more poorly on the emotion recognition task than the TD children. The deaf children with ASD showed a deficit in emotion recognition during sign language processing analogous to the deficit in vocal emotion recognition that has been observed in hearing children with ASD.

Study of thermal and hydraulic efficiency of supersonic tube of temperature stratification

NASA Astrophysics Data System (ADS)

Tsynaeva, Anna A.; Nikitin, Maxim N.; Tsynaeva, Ekaterina A.

2017-10-01

Efficiency of supersonic pipe for temperature stratification with finned subsonic surface of heat transfer is the major of this paper. Thermal and hydraulic analyses of this pipe were conducted to asses effects from installation of longitudinal rectangular and parabolic fins as well as studs of cylindrical, rectangular and parabolic profiles. The analysis was performed based on refined empirical equations of similarity, dedicated to heat transfer of high-speed gas flow with plain wall, and Kármán equation with Nikuradze constants. Results revealed cylindrical studs (with height-to-diameter ratio of 5:1) to be 1.5 times more efficient than rectangular fins of the same height. At the same time rectangular fins (with height-to-thickness ratio of 5:1) were tend to enhance heat transfer rate up to 2.67 times compared to bare walls from subsonic side of the pipe. Longitudinal parabolic fins have minuscule effect on combined efficiency of considered pipe since extra head losses void any gain of heat transfer. Obtained results provide perspective of increasing efficiency of supersonic tube for temperature stratification. This significantly broadens device applicability in thermostatting systems for equipment, cooling systems for energy converting machinery, turbine blades and aerotechnics.

Annual Research Report 1 October 1978-30 September 1979.

DTIC Science & Technology

1979-01-01

Roeder, R. G. and Rutter, W. J. Multiple acid polymerases in ribonucleic acid synthesis during sea urchin development. Biochemistry 9: 2543-2554...with ultrastructural transmission electron microscopy (TEM) studies and scanning electron microscopy ( SEM ) stud- ies of lateral ventricular lining and...1I alterations in animals about 100 days after Silastic implantation. SEM studies show flattening and stretching of ependymal cells in the dorsomedial

U.S.-MEXICO BORDER PROGRAM ARIZONA BORDER STUDY--STANDARD OPERATING PROCEDURE FOR OPERATION, CALIBRATION, AND ROUTINE USE OF THE SPECTRACE 9000 FIELD PORTABLE X-RAY FLUORESCENCE ANALYZER (UA-L-10.1)

EPA Science Inventory

The purpose of this SOP is to describe the procedures for operating and calibrating the Spectrace 9000 field portable X-ray fluorescence analyzer. This procedure applies to the determination of metal concentrations in samples during the Arizona NHEXAS project and the Border stud...

Lightweight Energy Absorbers for Blast Containers

NASA Technical Reports Server (NTRS)

Balles, Donald L.; Ingram, Thomas M.; Novak, Howard L.; Schricker, Albert F.

2003-01-01

Kinetic-energy-absorbing liners made of aluminum foam have been developed to replace solid lead liners in blast containers on the aft skirt of the solid rocket booster of the space shuttle. The blast containers are used to safely trap the debris from small explosions that are initiated at liftoff to sever frangible nuts on hold-down studs that secure the spacecraft to a mobile launch platform until liftoff.

Nuclear reactor control room construction

DOEpatents

Lamuro, R.C.; Orr, R.

1993-11-16

A control room for a nuclear plant is disclosed. In the control room, objects labelled 12, 20, 22, 26, 30 in the drawing are no less than four inches from walls labelled 10.2. A ceiling contains cooling fins that extend downwards toward the floor from metal plates. A concrete slab is poured over the plates. Studs are welded to the plates and are encased in the concrete. 6 figures.

Nuclear reactor control room construction

DOEpatents

Lamuro, Robert C.; Orr, Richard

1993-01-01

A control room 10 for a nuclear plant is disclosed. In the control room, objects 12, 20, 22, 26, 30 are no less than four inches from walls 10.2. A ceiling 32 contains cooling fins 35 that extend downwards toward the floor from metal plates 34. A concrete slab 33 is poured over the plates. Studs 36 are welded to the plates and are encased in the concrete.

George Bush May Not Like Black People, but No One Gives a Dam about Indigenous Peoples: Visibility and Indianness after the Hurricanes

ERIC Educational Resources Information Center

King, C. Richard

2008-01-01

Shortly after the devastation of Hurricane Katrina became clear, NBC televised "A Concert for Hurricane Relief," a star-studded event watched by more than fourteen million Americans. Perhaps the most memorable moment of the evening had little to do with charity. Hip-hop artist Kanye West went "off-script" during a live segment…

Unusual Giant Prostatic Urethral Calculus

PubMed Central

Bello, A.; Maitama, H. Y.; Mbibu, N. H.; Kalayi, G. D.; Ahmed, A.

2010-01-01

Giant vesico-prostatic urethral calculus is uncommon. Urethral stones rarely form primarily in the urethra, and they are usually associated with urethral strictures, posterior urethral valve or diverticula. We report a case of a 32-year-old man with giant vesico-prostatic (collar-stud) urethral stone presenting with sepsis and bladder outlet obstruction. The clinical presentation, management, and outcome of the giant prostatic urethral calculus are reviewed. PMID:22091328

Correlating levels of type III secretion and secreted proteins with fecal shedding of Escherichia coli O157:H7 in cattle

USDA-ARS?s Scientific Manuscript database

The locus of enterocyte effacement (LEE) encodes a type III secretion system (T3SS) for secreting factors that enable Escherichia coli O157:H7 to produce attaching and effacing lesions (A/E) on epithelial cells. The importance of LEE-encoded proteins in intestinal colonization of cattle is well-stud...

Reduction of Residual Stress and Distortion in HY100 and HY130 High Strength Steels During Welding

DTIC Science & Technology

1989-06-01

SMAW), Gas Tungsten Arc Welding ( GTAW ), Gas Metal Arc Welding (GMAW), Submerged Arc Welding (SAW), and Stud Welding (SW) the recommended joint...3.2 4.83 Cr Chromium -(3) 1.5 .55 M0 Molybdium -(3) .40 .40 V Vanadium -(3) .08 T i Titanium -(3) .005 Identifier ABS Class B USX TAG328 Lukens

HIV envelope glycoprotein imaged at high resolution | Center for Cancer Research

Cancer.gov

The outer surface of the human immunodeficiency virus (HIV) is surrounded by an envelope studded with spike-shaped glycoproteins called Env that help the deadly virus identify, bind, and infect cells. When unbound, Env exists in a “closed” conformational state. Upon binding with target cells, such as CD4+ T cells, the protein transitions to an “open” configuration. Given that

Challenging Nuclear Abolition

DTIC Science & Technology

2009-08-01

Institution; Jan Lodal, past president of the Atlantic Council of the United States; billionaire Richard Branson ; and a substantial num- ber of senior...Association, Center for Strategic and International Stud- ies, Nuclear Threat Initiative, American Physics Society, and Sir Richard Branson’s newly...uncertain and likely declining reliability. (Reprinted from a briefing by retired admiral Richard Meis.) 01-Text.indd 4 10/23/09 9:30:34 AM 5 He

Behaviour of partially composite precast concrete sandwich panels under flexural and axial loads

NASA Astrophysics Data System (ADS)

Tomlinson, Douglas George

Precast concrete sandwich panels are commonly used on building exteriors. They are typically composed of two concrete wythes that surround rigid insulation. They are advantageous as they provide both structural and thermal resistance. The structural response of sandwich panels is heavily influenced by shear connectors that link the wythes together. This thesis presents a study on partially composite non-prestressed precast concrete wall panels. Nine flexure tests were conducted on a wall design incorporating 'floating' concrete studs and Glass Fibre Reinforced Polymer (GFRP) connectors. The studs encapsulate and stiffen the connectors, reducing shear deformations. Ultimate loads increased from 58 to 80% that of a composite section as the connectors' reinforcement ratio increased from 2.6 to 9.8%. This design was optimized by reinforcing the studs and integrating them with the structural wythe; new connectors composed of angled steel or Basalt-FRP (BFRP) were used. The load-slip response of the new connector design was studied through 38 double shear push-through tests using various connector diameters and insertion angles. Larger connectors were stronger but more likely to pull out. Seven flexure tests were conducted on the new wall design reinforced with different combinations of steel and BFRP connectors and reinforcement. Composite action varied from 50 to 90% depending on connector and reinforcement material. Following this study, the axial-bending interaction curves were established for the new wall design using both BFRP and steel connectors and reinforcement. Eight panels were axially loaded to predesignated loads then loaded in flexure to failure. A technique is presented to experimentally determine the effective centroid of partially composite sections. Beyond the tension and compression-controlled failure regions of the interaction curve, a third region was observed in between, governed by connector failure. Theoretical models were developed for the bond-slip behaviour of the shear connection and to analyze the full panel's flexural and axial response to determine the longitudinal shear force transferred between wythes and account for partial composite behavior. The models were validated against experiments and used to conduct a parametric study. Among several interesting findings, the study demonstrated how composite action increases with the slenderness of axially loaded panels.

Lens fiber organization in four avian species: a scanning electron microscopic study.

PubMed

Willekens, B; Vrensen, G

1985-01-01

The three-dimensional organization of the eye lenses of the chicken, the canary, the song-thrush and the kestrel was studied using light and scanning electron microscopy. The lenses of birds are characterized by the presence of two distinct compartments: the annular pad and the main lens body, separated by a cavum lenticuli. The annular pad fibers had a hexagonal circumference all contained a round nucleus and except for the canary were smooth-surfaced and lacking anchoring devices. In the canary, however, the annular pad fibers were studded with edge protrusions and ball-and-socket junctions. The semicircular main lens body fibers of all four species were studded with ball-and-socket junctions and edge protrusions. In contrast with mammals these anchoring devices were present throughout the lens up to the embryonal nucleus. Superficially the main lens body fibers were extremely flat. Additionally membrane elevations and depressions and globular elements were found on these central fibers in three species, the kestrel being the exception. At the transition between annular pad and main lens body the fibers turned their course and the nuclei became oval and disappeared in the deeper aspect of the main lens body. The cavum lenticuli was filled with globules tied off from the annular pad fibers. It seems attractive to assume that the presence of a separated annular pad, a cavum lenticuli filled with globular elements, the extreme flatness of the superficial central fibers and the studding of these central fibers with anchoring devices up to the embryonal nucleus are morphological expressions of the mouldability of the bird's eye lenses and consequently would explain their efficient accommodative mechanism including formation of a lenticonus. The presence of nuclei in the annular pad fibers and their typical change at the transitional zone between annular pad and main lens body are suggestive for a two-phased differentiation in bird's lens fibers: differentiation of the germinative epithelial cells to annular pad fibers which migrate to the main lens body after which they differentiate further to main lens body fibers.

Improved Joining of Metal Components to Composite Structures

NASA Technical Reports Server (NTRS)

Semmes, Edmund

2009-01-01

Systems requirements for complex spacecraft drive design requirements that lead to structures, components, and/or enclosures of a multi-material and multifunctional design. The varying physical properties of aluminum, tungsten, Invar, or other high-grade aerospace metals when utilized in conjunction with lightweight composites multiply system level solutions. These multi-material designs are largely dependent upon effective joining techAn improved method of joining metal components to matrix/fiber composite material structures has been invented. The method is particularly applicable to equipping such thin-wall polymer-matrix composite (PMC) structures as tanks with flanges, ceramic matrix composite (CMC) liners for high heat engine nozzles, and other metallic-to-composite attachments. The method is oriented toward new architectures and distributing mechanical loads as widely as possible in the vicinities of attachment locations to prevent excessive concentrations of stresses that could give rise to delaminations, debonds, leaks, and other failures. The method in its most basic form can be summarized as follows: A metal component is to be joined to a designated attachment area on a composite-material structure. In preparation for joining, the metal component is fabricated to include multiple studs projecting from the aforementioned face. Also in preparation for joining, holes just wide enough to accept the studs are molded into, drilled, or otherwise formed in the corresponding locations in the designated attachment area of the uncured ("wet') composite structure. The metal component is brought together with the uncured composite structure so that the studs become firmly seated in the holes, thereby causing the composite material to become intertwined with the metal component in the joining area. Alternately, it is proposed to utilize other mechanical attachment schemes whereby the uncured composite and metallic parts are joined with "z-direction" fasteners. The resulting "wet" assembly is then subjected to the composite-curing heat treatment, becoming a unitary structure. It should be noted that this new art will require different techniques for CMC s versus PMC's, but the final architecture and companion curing philosophy is the same. For instance, a chemical vapor infiltration (CVI) fabrication technique may require special integration of the pre-form and

Heterologous Minor Coat Proteins of Citrus Tristeza Virus Strains Affect Encapsidation, but the Coexpression of HSP70h and p61 Restores Encapsidation to Wild-Type Levels

USDA-ARS?s Scientific Manuscript database

The long flexuous bipolar virions of Citrus tristeza virus (CTV), a Closterovirus, are encapsidated with two capsid proteins at opposite ends: the minor coat protein (CPm) encapsidates the 5’ 630 nts of the genomic RNA and the major coat protein encapsidates the remainder of the genome. In this stud...

Vaxfectin (registered trademark) Enhances Both Antibody and In Vitro T Cell Responses to Each Component of a 5-gene Plasmodium falciparum Plasmid DNA Vaccine Mixture Administered at Low Doses

DTIC Science & Technology

2010-01-01

received intramus- cular injections in the tibialis anterior muscle pDNA formu lated in PBS or Vaxfectin® using insulin syringes (0.3 ml: Becton Dick... phosphatidylcholine (DSPC) liposomes in Leishmania vaccine stud- ies and report long-term immunity in mice when the adjuvant was added with the

Lego Bricks and the Octet Rule: Molecular Models for Biochemical Pathways with Plastic, Interlocking Toy Bricks

ERIC Educational Resources Information Center

Lin, Henry J.; Lehoang, Jennifer; Kwan, Isabel; Baghaee, Anita; Prasad, Priya; Ha-Chen, Stephanie J.; Moss, Tanesha; Woods, Jeremy D.

2018-01-01

The 8 studs on a 2 × 4 Lego brick conveniently represent the outer shell of electrons for carbon, nitrogen, and oxygen atoms. We used Lego bricks to model these atoms, which are then joined together to form molecules by following the Lewis octet rule. A variety of small biological molecules can be modeled in this way, such as most amino acids,…

Debate on Global Warming as a Socio-Scientific Issue: Science Teaching towards Political Literacy

ERIC Educational Resources Information Center

Pereira dos Santos, Wildson Luiz

2014-01-01

The focus of this response to the original article by Tom G. H. Bryce and Stephen P. Day ("Cult Stud Sci Educ." doi:10.1007/s11422-012-9407-1, 2013) is the use of empirical data to illustrate and expand the understanding of key points of their argument. Initially, I seek to discuss possible answers to the three questions posed by the…

Health Effects of Embedded Depleted Uranium Fragments.

DTIC Science & Technology

1996-11-15

18]. The metabolic (approximately 99.8%). DU emits alpha (a), beta models required to estimate the chemical and radio- (3), and weak gamma ( y ...for the large-scale screening of patients who choosing an animal model for carcinogenesis stud- may be at increased risk of developing cancer . ies...appears warranted biomarkers for neoplastic tissues. since it is likely to provide better assurance of detecting changes that are associated with Cancer

A Comparative Study of the Employee Skills/Training Acceptable to Employers Under Varying Degrees of Labor Market Stringencies. Final Report.

ERIC Educational Resources Information Center

Fisher, W. Halder; And Others

The purposes of this stud y were to test the dependability of stated employee selection criteria, to ascertain the degree of congruence between stated and actual selection criteria, and to determine the degree of change in criteria due to "looseness" or "tightness" of the local labor market. Seven test labor market areas representing a variety of…

Manufacturing process applications team (MATeam). [NASA/industry relations

NASA Technical Reports Server (NTRS)

Bangs, E. R.

1978-01-01

Forty additional statements were added to the list of 150 problem/opportunity statements identifying possibilities for transfer of NASA technology to various manufacturing industries. Selected statements that are considered to have a high potential for transfer in the 1978 program year are presented in the form of goals and milestones. The transfer of a flux used in the stud welding of aluminum is reported. Candidate RTOP programs are identified.

Scepticism and Trust: Two Counterpoint Essentials in Science Education for Complex Socio-Scientific Issues

ERIC Educational Resources Information Center

Fensham, Peter J.

2014-01-01

In this response to Tom G. K. Bryce and Stephen P. Day's ("Cult Stud Sci Educ." doi:10.1007/s11422-013-9500-0, 2013) original article, I share with them their interest in the teaching of climate change in school science, but I widen it to include other contemporary complex socio-scientific issues that also need to be discussed. I…

Trials of prototype roll-feed, high-temperature dryer for 8/4 southern pine

Treesearch

P. Koch

1974-01-01

Eight-foot studs measuring 1.75 by 3.84 inches in cross section were cut from veneer cores and dried in a prototype continuous kiln that provided complete mechanical restraint against warp. Twenty-four hours on a high-temperature schedule brought the pieces from 87.9 to 8.3 percent moisture content without casehardening. Crook, bow, and twist were half that found in...

Energy Alternatives. Volume 2, No. 8

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mielke, G.

1984-08-01

Some new ways of financing energy-efficient homes are briefly discussed. A vertical axis wind turbine operating at an Illinois residence is described. The failure of the 40% federal renewable energy tax credit to be extended beyond December 31, 1985, and legislation concerning the manufacture, importation, and use of alcohol fuels are reported. An alternative way of constructing exterior corners using only two studs with drywall clips is described. (LEW)

"That's How We Roll": A Case Study of a Recently Arrived Refugee Student in an Urban High School

ERIC Educational Resources Information Center

Roxas, Kevin; Roy, Laura

2012-01-01

This critical case study of one, Somali Bantu male high school student illuminates the struggle for recently arrived refugees at the high school level. Few educational research studies describe how recently arrived refugee students and their families make their transition to US schools (Ngo et al. in "Hmong Stud J" 8:1-35, 2007; Hones and Cha in…

Women’s G Tolerance

DTIC Science & Technology

1986-08-01

for the groups matched by age (70 pairs), weight sickness, uncomfortable feelings of distension in arms (26 pairs), and act~vity status (84 pairs...mass-spring-damper) s ,stem Straining G tolerance, being dpendent on skeletal having a resonant frequency above about I Hz. As muscular strength and...of the women’s G tolerance stud\\ scclic variations in muscular strength and endurance. was below 0.1 Hz (11), the production of any significant

Process for straightening and drying southern pine 2 by 4's in 24 hours

Treesearch

Peter Koch

1971-01-01

In 21 hours under mechanical restraint and in a kiln providing a cross-circulation velocity of 1,000 f.p.m. at dry-and wet-bulb temperatures of 240 and 160oF., followed by 3 hours at 195 and 185oF., southern pine 2 by 4 studs cut from steamed veneer cores or small logs were dried to 9-percent moisture content (Standard...

Guidelines for the Sound Insulation of Residences Exposed to Aircraft Operations

DTIC Science & Technology

1992-10-01

scale the incident sound. The values of sound discriminates against the lower frequencies absorption coefficients usually range from below 1000 hertz...Regulations achieve them, must take into account the establishing a single system of noise measure- sometimes conflicting needs of the parties ment...fasteners to the studs to prevent sagging. 5. Cut new gypsumboard so that it fits tightly against walls, floor, and ceiling. 6. Apply acoustical

Handling of buses on slippery roads during the influence of side wind--a study of the effects of different tyres.

PubMed

Hjort, Mattias; Jansson, Jonas

2010-05-01

Accident statistics assembled by the Swedish National Road and Transport Research Institute (VTI) have shown that buses are overrepresented when it comes to accidents on icy and snowy roads. For a better understanding of the problem, the performance of modern summer and winter tyres on winter road conditions had to be assessed. The objective of this work has been to go beyond standard road grip studies, and instead investigate how the driver's possibility to deal with one challenging situation depends on the tyres and tyre configuration. This paper describes a novel methodology where measurements with different tyres on ice in VTI's tyre test facility, enabled a simulator study for evaluating the impact of different tyre characteristics when driving in conditions with strong side wind on a slippery road. The main results of the study are: to deal with strong side wind, good front wheel grip is most important, and while non-studded winter tyres provided little or no improvement over summer tyres, studded winter tyres significantly reduced the risk to run off the road. Furthermore, it is very difficult for the drivers to judge, beforehand, whether a vehicle with a particular tyre configuration will perform good or bad. Copyright (c) 2009 Elsevier Ltd. All rights reserved.

Corrosion Development of Carbon Steel Grids and Shear Connectors in Cracked Composite Beams Exposed to Wet–Dry Cycles in Chloride Environment

PubMed Central

Xue, Wen; Chen, Ju; Jiang, Ao-yu

2018-01-01

The corrosion development of the reinforcement and shear stud connectors in the cracked steel–concrete composite beams under the salt-fog wet–dry cycles is presented in this investigation. Seven identical composite beams with load-induced concrete cracks were exposed to an aggressive chloride environment. The reinforcement and shear connectors were retrieved after specimens underwent a specified number of wet–dry cycles to obtain the corrosion pattern and the cross-section loss at different exposure times and their evolutions. The crack map, the corrosion pattern and the cross-section loss were measured and presented. Based on the experimental results, the influence of crack characteristics, including crack widths, orientations and positions on the corrosion rate and distribution, were accessed. Moreover, the effects of the connecting weldments on the corrosion initiations and patterns were analyzed. It was shown that the corrosion rate would increase with the number of wet–dry cycles. The characteristics of load-induced cracks could have different influences on the steel grids and shear stud connectors. The corrosion tended to initiate from the connecting weldments, due to the potential difference with the parent steel and the aggressive exposure environment, leading to a preferential weldment attack. PMID:29565836

Technology Solutions Case Study: Hygrothermal Performance of a Double-Stud Cellulose Wall

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2015-06-01

Moisture problems within the building shell can be caused by a number of factors including excess interior moisture that is transported into the wall through air leakage and vapor drive, bulk water intrusion from leaks and wind-driven rain, capillary action from concrete to wood connections, and through wetted building materials such as siding wetted from rain splash back. With the increasing thickness of walls, moisture issues could increase. Several builders have successfully used “double-wall” systems to more practically achieve higher R-values in thicker framed walls. A double wall typically consists of a load-bearing external frame wall constructed with 2 ×more » 4 framing at 16 in. on center using conventional methods. After the building is enclosed, an additional frame wall is constructed several inches inside the load-bearing wall. Several researchers have used moisture modeling software to conduct extensive analysis of these assemblies; however, little field research has been conducted to validate the results. In this project, the Building America research team Consortium for Advanced Residential Buildings monitored a double-stud assembly in climate zone 5A to determine the accu¬racy of moisture modeling and make recommendations to ensure durable and efficient assemblies.« less

Effects of season on boar semen parameters and antioxidant enzymes in the south subtropical region in Brazil.

PubMed

Argenti, L E; Parmeggiani, B S; Leipnitz, G; Weber, A; Pereira, G R; Bustamante-Filho, I C

2018-02-01

Although boar semen productivity is affected by seasonality, its effects are not equal among different regions which raise concerns regarding the profitability of boar stud farms. Therefore, the goals of this study were (i) to evaluate the seasonal effect on semen production in a commercial boar stud farm located in a subtropical climate region and (ii) to verify whether the activities of superoxide dismutase and glutathione peroxidase in spermatozoa and seminal plasma were associated with seminal traits of fresh and cooled semen. Nine boars were collected twice per season, and routine seminal parameter analyses were performed together with superoxide dismutase and glutathione peroxidase activities in seminal plasma and spermatozoa. Despite a reduction in sperm concentration in spring and summer, most seminal parameters were constant year-round. Temperature-humidity index was higher in the summer compared to spring, autumn and winter (p < .05). Superoxide dismutase activity in spermatozoa was increased in summer compared to autumn and winter (p < .05). The activities of both enzymes in seminal plasma and spermatozoa glutathione peroxidase remained unaltered throughout the seasons. In conclusion, seasonality showed little influence in overall boar seminal parameters despite microclimatic differences among seasons, and spermatozoa collected during summer increased superoxide dismutase activity. © 2018 Blackwell Verlag GmbH.

Genotyping in the Brazilian Criollo Horse Stud Book: resources and perspectives.

PubMed

Costa, M A P; Bressel, R M C; Almeida, D B; Oliveira, P A; Bassini, L N; Moreira, C G A; Manzke, V H B; Siewerdt, F; Moreira, H L M

2010-08-24

The goal of this research was to evaluate the ability of the genotyping information available in the Brazilian Criollo Horse Stud Book to describe the genetic variability of the breed and the exclusion probability determined in comparative tests. Altogether, two softwares were used in the analyses of the available genotypes: Cervus 3.0.3 and Genepop 4.0. Eight microsatellite markers totaled 109 alleles, with an average of 13.6 +/- 0.6 alleles per locus. Large differences between expected and observed heterozygosity were ubiquitous (0.821 +/- 0.07 and 0.470 +/- 0.17, respectively). Although the estimated null allele frequency caused initial concern (0.284 +/- 0.199), it is likely that it was a reflection of the inbreeding coefficients found (0.432 +/- 0.184). All loci showed significant deviation from Hardy-Weinberg equilibrium, with heterozygote deficit (P < 0.0001) and genotypic linkage disequilibrium with at least one marker. The high polymorphic information content (0.798 +/- 0.088) could not warrant exclusion power for three loci (HMS7, HMS6 and HTG4) above 50% (0.491 +/- 0.158). However, combined exclusion probability reached 99.61%, a level close to ideal. The results demonstrate the excellent performance of the markers assessed in describing the genetic status of the breed and suggest the considerable ability to establish parentage.

Laser-Plasma Instabilities by Avoiding the Strong Ion Landau Damping Limit: The Central Role of Statistical, Ultrafast, Nonlinear Optical Laser Techniques (SUNOL)

NASA Astrophysics Data System (ADS)

Afeyan, Bedros; Hüller, Stefan; Montgomery, David; Moody, John; Froula, Dustin; Hammer, James; Jones, Oggie; Amendt, Peter

2014-10-01

In mid-Z and high-Z plasmas, it is possible to control crossed bean energy transfer (CBET) and subsequently occurring single or multiple beam instabilities such as Stimulated Raman Scattering (SRS) by novel means. These new techniques are inoperative when the ion acoustic waves are in their strong damping limit, such as occurs in low Z plasmas with comparable electron and ion temperatures. For mid-Z plasmas, such as Z = 10, and near the Mach 1 surface, the strong coupling regime (SCR) can be exploited for LPI mitigation. While at higher Z values, it is thermal filamentation in conjunction with nonlocal heat transport that are useful to exploit. In both these settings, the strategy is to induce laser hot spot intensity dependent, and thus spatially dependent, frequency shifts to the ion acoustic waves in the transient response of wave-wave interactions. The latter is achieved by the on-off nature of spike trains of uneven duration and delay, STUD pulses. The least taxing use of STUD pulses is to modulate the beams at the 10 ps time scale and to choose which crossing beams are overlapping in time and which are not. Work supported by a grant from the DOE NNSA-OFES joint program on HEDP

Modeling and experimental characterization of electromigration in interconnect trees

NASA Astrophysics Data System (ADS)

Thompson, C. V.; Hau-Riege, S. P.; Andleigh, V. K.

1999-11-01

Most modeling and experimental characterization of interconnect reliability is focussed on simple straight lines terminating at pads or vias. However, laid-out integrated circuits often have interconnects with junctions and wide-to-narrow transitions. In carrying out circuit-level reliability assessments it is important to be able to assess the reliability of these more complex shapes, generally referred to as `trees.' An interconnect tree consists of continuously connected high-conductivity metal within one layer of metallization. Trees terminate at diffusion barriers at vias and contacts, and, in the general case, can have more than one terminating branch when they include junctions. We have extended the understanding of `immortality' demonstrated and analyzed for straight stud-to-stud lines, to trees of arbitrary complexity. This leads to a hierarchical approach for identifying immortal trees for specific circuit layouts and models for operation. To complete a circuit-level-reliability analysis, it is also necessary to estimate the lifetimes of the mortal trees. We have developed simulation tools that allow modeling of stress evolution and failure in arbitrarily complex trees. We are testing our models and simulations through comparisons with experiments on simple trees, such as lines broken into two segments with different currents in each segment. Models, simulations and early experimental results on the reliability of interconnect trees are shown to be consistent.

Technology of research of hydroturbine unit work using seismic methods

NASA Astrophysics Data System (ADS)

Seleznev, V. S.; Liseikin, A. V.; Gromyko, P. V.; Soloviev, V. M.

2013-05-01

On August, 17, 2009 one of the most significant accident in hydropower engineering was happened at Sayano-Shushenskaya Hydroelectric Power Station. Specialists of Geophysical Survey SB RAS took part in the State Committee on investigation of the accident cause at Sayano-Shushenskaya HPS. It was determined, that the cause of the accident was a break of stud-bolts on the turbine cover. Why stud-bolts did not stand a load? There were assumptions that hydraulic shock provoked the accident. But, if it is so, seismic station "Cheremushky", situated in 4 km away from the HPS, should has a record of this event. First of all, investigating the record, got at the seismic station in the moment of the accident, it was determined that strength of seismic waves, recorded at the moment of the accident, did not exceed strength of waves got at trotyl explosion of 500 g at a distance to 4 km. The version of hydraulic shock was not proved. There were distinguished low-frequency oscillations and it was determined that the hydroturbine unit (HU) had been raised up more then 10 m in height for 10 sec. Analyzing the seismic station records during the period of more than a year before the accident and records of operating modes of different HU, there was determined that oscillations radiated by second (damaged) HU were approximately 1.5 times more intense than oscillations from all other HU. After the accident at Sayano-Shushenskaya HPS hydroturbine units were started in turns: at first there were started hydroturbine units of old construction (3, 4, 5, 6), then HP of new construction (1, 7, 8, 9). We installed 10 - 15 three-component seismic stations in different points around a HU and studied field of seismic oscillations from it's work. It was determined, that HU radiates a set of monochromatic oscillations divisible by speed of rotation equal to 2.381 Hz. Change of these signals amplitude is connected with change of HU operation modes. Research of changes in oscillations spectral distribution in time allows to control HU work and it's technical condition. It was determined, that natural frequency of turbine cover (when water entry is closed) has several maximums, and it is situated in the range of 60 - 110 Hz. Power radiation of monochromatic signals is registered in the same range from old hydroturbine units when they work, especially on double blade frequency equal to 76.2 Hz. It turns out that the turbine cover and fixed it stud-bolts were in condition of constant resonance excitation during work of HU. Since second HU was arranged in such a way that oscillations radiated by it exceeded oscillations from other aggregates, the accident occurred exactly on this HU. The real cause of the accident is connected with the fact that at calculation of the turbine cover fastening it was not taken into account the fact that it would work in constant resonance excitation. On new constructed HU number of stud-bolts was increased and the amplitude of monochromatic oscillations was considerably reduced.

What Students and Researchers in Nanoscience and Nanotechnology Should Know about PUS and STS: A Look at Fages and Albe's Viewpoint on Social Issues in Nanoscience and Nanotechnology Master's Degrees

ERIC Educational Resources Information Center

Pouliot, Chantal

2015-01-01

In this paper, in order to pursue the conversation begun by Fages and Albe ("Cult Stud Sci Educ" 2014), I highlight three conceptual contributions that could be made by familiarizing nanoscience and nanotechnology researchers and engineers with the work being carried out in science and technology studies and public understanding of…

Construction Guide to Next-Generation High-Performance Walls in Climate Zones 3-5 - Part 1: 2x6 Walls

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kochkin, V.; Wiehagen, J.

2017-08-31

Part 1 of this Construction Guide to High-Performance Walls in Climate Zones 3-5 provides time-proven, practical, and cost-effective strategies for constructing durable, energy-efficient walls. It addresses walls constructed with 2x6 wood frame studs, wood structural panel (WSP) exterior sheathing, and a cladding system installed over WSP sheathing in low-rise residential buildings up to three stories high.

Construction Guide to Next-Generation High-Performance Walls in Climate Zones 3-5 - Part 1: 2x6 Walls

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kochkin, V.; Wiehagen, J.

Part 1 of this Construction Guide to High-Performance Walls in Climate Zones 3-5 provides time-proven, practical, and cost-effective strategies for constructing durable, energy-efficient walls. It addresses walls constructed with 2x6 wood frame studs, wood structural panel (WSP) exterior sheathing, and a cladding system installed over WSP sheathing in low-rise residential buildings up to three stories high.

In Response to David Greenwood's "Place Mobility and Faculty Life: Mindfulness through Change" through the Lens of Science Teacher Education Programs

ERIC Educational Resources Information Center

Nyaema, Mary K.

2017-01-01

In writing this review, I draw on the experience of David Greenwood ("Cult Stud Sci Educ" 10:5-16, 2015) whose ethnographic study sheds light on his growth as a faculty member who has taught in various settings that are quite different from the culture that he grew up with. I extend his thoughts on ecological mindfulness to encompass a…

From War to Deterrence? Israel-Hezbollah Conflict Since 2006

DTIC Science & Technology

2014-05-01

Israeli Air Force (IAF) strike on a Syrian reactor in September 2007, the issue of the Lebanese front, although unsettled, was moved to the...widespread con- fusion over the exact level of readiness and coverage of its missile defense architecture. Given the current passion of Israeli...Variations on a Theme: The Conceptual - ization of Deterrence in Israeli Strategic Thinking,” Security Stud- ies, Vol. 7, No. 3, Spring 1998, pp. 145-181

Ultra-wideband Radar for Building Interior Imaging

DTIC Science & Technology

2008-12-01

same cross range resolution as a monostatic configuration with an equal number of transmitters and receivers (Ressler et al., 2007). In terms of...By this procedure we ensure a constant cross range resolution across the entire image. 2.2. Measurements setup The one story abandoned barrack...identify its geometry and materials. Two-by-four wooden studs (3.8 cm x 8.9 cm cross -section dimensions) are used for most exterior and interior walls

Development and Evaluation of Stereographic Display for Lung Cancer Screening

DTIC Science & Technology

2006-12-01

and also by grant CA80836 from the National Cancer Institute, National Institutes of Health . The content of the contained information does not...Evers H, Henn C, Glombitza G, Meinzer HP. Interactive real- time Doppler-ultrasound visualization of the heart. Stud Health Technol Inform. 2000;70:119...nodule, the scoring form with questionnaire related to the detected nodule would pop up for nodule assessment. We have also implemented mouse cursor as

Design Constructibility Reviews.

DTIC Science & Technology

1987-01-01

specifications for base and sub-base courses, and wearing course.I Item 21 - Has provision been made in the specifications for positive control of the temperature...of the bituminous material? Item 22 - Test results on samples of asphalt , aggregate, sand and mix should be obtained from the plant prior to placing...in the * drawings. Item 3 - Make sure that stud types, sizes and pacinqs are spelled out in the plans and sc-i catr-. Item 4 - All welders that will

Paint Pavement Marking Performance Prediction Model That Includes the Impacts of Snow Removal Operations

DTIC Science & Technology

2011-03-01

Hypothesized that snow plows wear down mountain road pavement markings. 2007 Craig et al. -Edge lines degrade slower than center/skip lines 2007...retroreflectivity to create the models. They discovered that paint pavement markings last 80% longer on Portland Cement Concrete than Asphalt Concrete at low AADT...retroreflectivity, while yellow markings lost 21%. Lu and Barter attributed the sizable degradation to snow removal, sand application, and studded

Alternative Governance Structures in Megacities: Threats or Opportunities

DTIC Science & Technology

2016-11-01

Intelligence Stud- ies and Data Informatics at Mercyhurst University as well as a graduate of that program. She teaches intelli- gence communication...States imported $11.6 billion in oil in 2013;35 and Karachi, Pakistan, due to its location at the crossroad of India and China and its state’s con...offer sustainable long-term solu- tions to Karachi’s violent politics. 38 Lagos, Nigeria. Although the United States imports 70 percent less oil

Sperm yield after single layer centrifugation with Androcoll-E is related to the potential fertility of the original ejaculate.

PubMed

Morrell, J M; Stuhtmann, G; Meurling, S; Lundgren, A; Winblad, C; Macias Garcia, B; Johannisson, A

2014-05-01

Many attempts have been made to identify laboratory tests that are predictive of sperm fertility, both to improve the quality of stallion semen doses for artificial insemination (AI) and to identify potential breeding sires if no fertility data are available. Sperm quality at the stud is mostly evaluated by assessing subjective motility, although this parameter can be poorly indicative of fertility. Sperm morphology and chromatin integrity in Swedish stallions are correlated to pregnancy rate after AI. Because single layer centrifugation (SLC) selects for spermatozoa with normal morphology and good chromatin, retrospective analysis was carried out to investigate whether sperm yield after SLC is linked to potential fertility. Commercial semen doses for AI from 24 stallions (five stallions with four ejaculates each, 19 stallions with three ejaculates each; n = 77) obtained during the breeding season were cooled, and sent overnight to the Swedish University of Agricultural Sciences in an insulated box for evaluation, with other doses being sent to studs for commercial AI. On arrival at Swedish University of Agricultural Sciences, the semen was used for SLC and also for evaluation of sperm motility, membrane integrity, chromatin integrity, and morphology. The seasonal pregnancy rates for each stallion were available. The yield of progressively motile spermatozoa after SLC (calculated as a proportion of the initial load) was found to be highly correlated with pregnancy rate (r = 0.75; P < 0.001). Chromatin damage was highly negatively correlated with pregnancy rate (r = -0.69; P < 0.001). Pregnancy rate was also correlated with membrane integrity (r = 0.58; P < 0.01), progressive motility (r = 0.63; P < 0.01), and normal morphology (r = 0.45; P < 0.05). In conclusion, these preliminary results show that sperm yield after SLC is related to the potential fertility of the original ejaculate, and could be an alternative indicator of stallion fertility if breeding data are not available. Single layer centrifugation is fast (30 minutes) and does not require expensive equipment, whereas other assays require a flow cytometer and/or specialist skills. An additional option could be to transport semen doses to a laboratory for SLC if the stud personnel do not want to perform the procedure themselves. Copyright © 2014 Elsevier Inc. All rights reserved.

Personality Types of Directors of Nursing in Nursing Homes.

DTIC Science & Technology

1986-05-01

RA I AAREA & WORK UNIT NUMBERS AFIT STUDENT AT: The University of Texas CONTROLLING OFFICE NAME AND ADDRESS 12. REPORT DATE AFIT/NR 1986 WPAFB 011...regulate life and control it. h. Perceiving - A person who lives in a flexible, spontaneous way, and aims to understand life and adapt to it. 5. Skilled... perceive and judge their environments. Different personality patterns emerged in Miller’s (1966), and Graham’s (1967) studies for those nursing stud

Postdeployment Symptom Changes and Traumatic Brain Injury and/or Posttraumatic Stress Disorder in Men

DTIC Science & Technology

2012-01-01

combat experi- ence criterion was used to identify a background sample of servicemembers who were at risk for incurring PTSD. Because women made up...the Diagnostic and Statistical Manual of Mental Disorders-Fourth Edition (DSM-IV) currently describes three clusters of PTSD symptoms (re-experiencing...appear on both question- naires or held no relevance to the conditions being stud- ied (e.g., indigestion, skin diseases ). A subject’s “yes” or “no

The Response of the Ligurian and Tyrrhenian Seas to a Summer Mistral Event: A Coupled Atmosphere-Ocean Approach

DTIC Science & Technology

2012-01-01

some extent. As well as the classical damping effect of surface friction on synop- tic storms via Ekman spindown (Holton, 2004), more recent stud...ies have suggested that surface stress can influence interior potential vorticity and thus storm growth (Adamson et al., 2006), and surface heat...the model simulations. Hence the mechanisms of SST response are similar to that found previously in tropical cyclones and extratropical low

A Study of Qualitative and Geometric Knowledge in Reasoning about Motion. Revision.

DTIC Science & Technology

1981-02-01

cpartinen of I)cfcnsc under Office of Naval Research contract N00014-80-C-0505 Acce’ Tin For F T" D/ c.,, i ’" d es -t A Stud’ of Qualitatise and...UNIT-VECTOR: ((number> (number>) UNtIT-NORMAL: ((number> (number>) PERPLNDtCULAR-EQUATIONS: ((equations>) PARABOLA REGION TYPE: PARABOLA TYPE: REGION...constraints. The mapping between domain objects and Metric Diagram elements is simple: Ball -> Point Surface -> Segment Trajectory -> Segment, Parabola

AICUZ Air Installation Compatible Use Zone Report for Mather Air Force Base, California.

DTIC Science & Technology

1982-09-01

Insulation shall be glass fiber or mineral wool . 1-4 Windows a. Windows other than as described in this sectionshall have a laboratory sound transmission...above. Ceilings shall be substantially airtight, with a minimum number of penetrations. I b. Glass fiber or mineral wool insulation at least 2" thick...throughout the cavity space behind the exterior sheathing and between wall studs. Insulation shall be glass fiber or mineral wool . 2-4 Windows a

Virus-like particles in cystic mammary adenoma of a snow leopard.

PubMed

Chandra, S; Laughlin, D C

1975-11-01

Virus-like particles were observed in the giant cells of a mammary adenoma of a snow leopard kept in captivity. Particles that measured 115 to 125 nm in diameter budded from the lamella of endoplasmic reticulum and were studded on their inner surfaces with dense granules (approximately 12 nm) that gave them their unique ultrastructural morphology. Such particles were not observed extracellularly. Type B or type C particles were not seen in the tumor tissue.

X-Ray Radiography Measurements of Shear Coaxial Rocket Injectors

DTIC Science & Technology

2013-02-01

turbofan engine exhaust, air blast furnaces, and liquid rocket engines) shear coaxial jets have been stud- ied for over sixty years [1]. In all applications...fluids as either single or multiple phases. Most of the fundamental coaxial jet research has been done using a single phase (either gas-gas or liquid ... liquid mixing). A brief review of single-phase coaxial jet research can be found in Schumaker and Driscoll [5]. Single-phase cases also include work

A Role for Small Antibody Fragments to Bind and Neutralize HIV | Center for Cancer Research

Cancer.gov

The surface of the Human Immunodeficiency Virus (HIV) is studded with numerous copies of the glycoprotein Env. Each Env spike is composed of three copies of the proteins gp41, which sits in the viral membrane, and gp120, which rests on top of each gp41 molecule. Env is essential for HIV-mediated infection because the binding of gp120 to the T cell surface receptor CD4

Summary of Federal Aviation Administration Responses to National Transportation Safety Board Safety Recommendations.

DTIC Science & Technology

1980-10-01

strike A-80-45 Beech C-18S electrical 63 terminal studs A-80-46 Redcoat Air Cargo, Ltd., 69 Bristol Britannia 253 crash Billerica, Massachusetts...Ltd., Bristol Britannia 253, which crashed about 7 minutes after takeoff from Boston’s Logan International Airport on February 16, 1980. We...1980. This recommendation resulted from the Board’s investigation of a Redcoat Air Cargo, Ltd., Bristol Britannia 253 which crashed at Billerica

Obstacles to the Termination of Air Force Activities.

DTIC Science & Technology

1986-04-01

sugsts how. it the Air Force leadership con- eludes that termination is necessary the Air Force can surmount the obstacles.’ The stud v was cMIduct ed...the Air Force leadership concludes that the termination of a major activity is a promising or necessary management option, the report suggests that it...complicated inter- nal political process; it takes time to work out. The top leadership should begin the process of corporate strategy building and priority

Nanotechnology-Enhanced Lubricants for RF MEMS Switches

DTIC Science & Technology

2011-03-01

and have greater capabilities. 2.1. Problem Background The Air Force employs numerous communication links between space -borne assets, airborne...beyond 10B of rated cold-switched life, such as high-value space -borne assets with 12+ year horizons to deployment. Warm-switched operation refers to...lids for 5 min. at 300W in oxygen 5. Stud bump substrates using a gold- silver alloy wire bonder – packages may be stored 6. Tack seal pre-form to lid

Controlling Energy Consumption in Single Buildings.

DTIC Science & Technology

1982-07-01

Asphalt shingles Apartment 1/2" plywood sheathing; 2"x4 ൦% sidewalls; 0% 1/2" plywood Building stud framing (16" c.c.); 2- endwalls. sheathing,3-1/2...cycling does produce additional wear on belts and motor starting circuits. Further, it may affect building air balance between building zones if more...4" common brick; 1/2" Single-strenght sheet; Asphalt shingles; Apartment plywood shetthing; light 30% sidewalls; 0% 1/2" plywood Buiiding framing; no

Estimating the Life Expectancy of Facilities

DTIC Science & Technology

1974-04-01

Expectancy 1’ Facilitie,." The applicable requirement code is QCR L.01.005. Mr. Frauik Beck is the OCEI Technical Monitor. ’The stud , ast% conducted under...59,327 1934 concrete HTS Spanish Tile 223 72410 3.390 1893 Rock Brick Asphalt 2406 74050 4,035 1956 Concrete Mascnry Composition *Abbrevimions: ASBSH...1tructure B. PipesI . Corro~ion A. FloorJoists 2. Scale I. Cracks C. Stoker---Coal Burner2. Deterioration I. Wear 3. Excessive deflection 4. Insect and

3D-Printing ‘Smarter’ Energy Absorbing Materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duoss, Eric

2014-08-29

Foams are, by nature, disordered materials studded with air pockets of varying sizes. Lack of control over the material’s architecture at the micrometer or nanometer scale can make it difficult to adjust the foam’s basic properties. But Eric Duoss and a team of Livermore researchers are using additive manufacturing to develop “smarter” silicone cushions. By architecting the structure at the micro scale, they are able to control macro-scale properties previously unachievable with foam materials.

DOE Zero Energy Ready Home Case Study: Palo Duro Homes, Albuquerque, New Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2013-09-01

Palo Duro uses advanced framing techniques like 2x6 24-inch on-center framing, open headers above windows on non-load-bearing walls, 2-stud corners, ladder blocking where walls intersect, and single top and bottom plates. These techniques reduce the amount of lumber in the wall, allowing more room for insulation and reducing costs and installation time. The builder garnered a 2013 Housing Innovation Award in the production builder category.

Experimental studies about the impact of traction sand on urban road dust composition.

PubMed

Kupiainen, Kaarle; Tervahattu, Heikki; Räisänen, Mika

2003-06-01

Traffic causes enhanced PM(10) resuspension especially during spring in the US, Japan, Norway, Sweden and Finland, among other countries. The springtime PM(10) consists primarily of mineral matter from tyre-induced paved road surface wear and traction sand. In some countries, the majority of vehicles are equipped with studded tyres to enhance traction, which additionally increases road surface wear. Because the traction sand and the mineral matter from the pavement aggregate can have a similar mineralogical composition, it has been difficult to determine the source of the mineral fraction in the PM(10). In this study, homogenous traction sand and pavement aggregate with different mineralogical compositions were chosen to determine the sources of PM(10) particles by single particle analysis (SEM/EDX). This study was conducted in a test facility, which made it possible to rule out dust contributions from other sources. The ambient PM(10) concentrations were higher when traction sand was used, regardless of whether the tyres were studded or not. Surprisingly, the use of traction sand greatly increased the number of the particles originating from the pavement. It was concluded that sand must contribute to pavement wear. This phenomenon is called the sandpaper effect. An understanding of this is important to reduce harmful effects of springtime road dust in practical winter maintenance of urban roads

Familial clustering of Taenia solium cysticercosis in the rural pigs of Mexico: hints of genetic determinants in innate and acquired resistance to infection.

PubMed

Sciutto, E; Martínez, J J; Huerta, M; Avila, R; Fragoso, G; Villalobos, N; de Aluja, A; Larralde, C

2003-10-20

In two rural villages of the state of Puebla, Mexico, where Taenia solium pig cysticercosis is highly endemic, 120 pairs of young out-bred piglets were used to assay what proved to be an effective synthetic peptide vaccine against naturally acquired cysticercosis. Because the piglets used were all sired by one of three distinct studs in many different out-bred sows, the prevalence and intensity of infection, as well as degree of protection conferred by the vaccine, could be related to each of the three stud families (A-C). The highest prevalence was found in the C family (25%), whilst the prevalence of B and A families were 21.6 and 4.4%, respectively. Familial clustering of cases was even more conspicuous in vaccinated pigs than in not-vaccinated ones: seven of the nine cysticercosis cases that occurred in the vaccinated group belonged to the C family (7/26) and two to the B family (2/23), whilst the vaccine rendered the A family totally resistant (0/71). Parasite numbers were also higher in the C family in both nai;ve and vaccinated pigs. Familial clustering of cases and of large parasite numbers in naive and vaccinated pigs hint to the relevance of their genetic background in their innate and acquired resistance to cysticercosis.

Abdominal perforation after rupture of a diamond-studded wire: a case report.

PubMed

Schmelzle, Moritz; Matthaei, Hanno; Tustas, Roy Y; Schmitt, Marcus; Müller-Mattheis, Volker; Linhart, Wolfgang; Eisenberger, Claus F; Knoefel, Wolfram T; Esch, Jan Schulte Am

2008-11-13

There are numerous cases of abdominal injuries due to bullets. Abdominal injuries due to bullets are a diagnostic and therapeutic challenge. Here, an unusual case of an abdominal perforation caused by a metal projectile, lead to confusion in the interpretation of the preoperative computer tomography. We present an unusual case of a 32-year-old male worker who sustained a "shot" to the left upper abdominal quadrant, as a result of a work-related accident. The projectile derived from a special wire that tore during operation. One chain element happened to accelerate towards the patients belly and perforated the abdominal wall. Computer tomography located the radiopaque projectile to the cortex of the left kidney and showed a lesion of the tail of the pancreas. The presence of intraperitoneal free air suggested a gastrointestinal perforation. Immediate open exploration of the peritoneal cavity and the retroperitoneal space revealed perforating lesions of the anterior and posterior gastric wall, as well as the pancreatic tail. The projectile was finally retrieved in the upper pole of the left kidney. The patient had a good clinical course subsequent to surgery and was discharged in good general condition. This case represents a rare form of a retained bullet injury and corroborates the need of sufficient measures of worker-protection in area of diamond-studded wire cutting devices.

DOE ZERH Case Study: Charles Thomas Homes, Anna Model, Omaha, NE

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

Case study of a DOE 2015 Housing Innovation Award winning custom home in the cold climate that got a HERS 48 without PV, with 2x6 24” on center walls with R-23 blown fiberglass, ocsf at rim joists, basement with plus 2x4 stud walls with R-23 blown fiberglass, with R-20 around slab, R-38 under slab; a vented attic with R-100 blown cellulose; 95% AFUE furnace, 14 SEER AC, ERV; heat pump water heater.

Space Science

NASA Image and Video Library

1994-11-01

An international effort to learn more about the complex interaction between the Earth and Sun took another step forward with the launch of WIND spacecraft from Kennedy Space Center (KSC). WIND spacecraft is studded with eight scientific instruments - six US, one French, and one - the first Russian instrument to fly on a US spacecraft - that collected data about the influence of the solar wind on the Earth and its atmosphere. WIND is part of the Global Geospace Science (GGS) initiative, the US contribution to NASA's International Solar Terrestrial Physics (ISTP) program.

Phenological observations and tree seed characteristics in an equatorial moist forest at Trombetas, Pará State, Brazil

Treesearch

Oliver H. Knowles; John A. Parrotta

1997-01-01

Seasonal patterns of flowering and fruiting were studìed over an 18-vear period in an upland (terra firme) primary forest area near Trombetas, Pará ìn centrai Amazonìa. The study included 160 common tree taxa. While a number of specìes produced flowers and fruits during all months, distinct seasonal patterns were observed. Flowerìng peaks usually occurred during the...

WIND Spacecraft Launch

NASA Technical Reports Server (NTRS)

1994-01-01

An international effort to learn more about the complex interaction between the Earth and Sun took another step forward with the launch of WIND spacecraft from Kennedy Space Center (KSC). WIND spacecraft is studded with eight scientific instruments - six US, one French, and one - the first Russian instrument to fly on a US spacecraft - that collected data about the influence of the solar wind on the Earth and its atmosphere. WIND is part of the Global Geospace Science (GGS) initiative, the US contribution to NASA's International Solar Terrestrial Physics (ISTP) program.

Core Length and Spray Width Measurements in Shear Coaxial Rocket Injectors from X-ray Radiography Measurements

DTIC Science & Technology

2015-05-01

liquid jet core; elliptical EPL is what would be expected from a cylinder of liquid and has previously been observed in diesel injector studies [22...and liquid rocket engines) shear coaxial jets have been stud- ied for over sixty years and have become a canonical problem for the study of rocket...research has been done using a single phase (either gas-gas or liquid - liquid mixing). A brief review of single-phase coaxial jet research can be

Construction of University of Missouri-Rolla’s Full Scale Cloud Simulation Chamber and Applied Research

DTIC Science & Technology

1985-03-01

aluminum outer walls by a matrix of studs screwed into blind holes in the inner wall plates and extending through the outer walls. Thermoelectric cooling...studied. The problem of the uncooled sample ports might have been dealt with, however the failure of several sections of thermoelectric cooling...encountered with the Proto I chamber. It should be kept in mind that the basic cooled wall design consists of thermoelectric cooling modules (TEM’s

Deployment Operation Procedures for the WHOI Ice-Tethered Profiler

DTIC Science & Technology

2007-05-01

mooring which would be pre-wound on a reel. These requirements led to the selection of a winch with a modular mooring reel and a disc -type brake for...lb * Brake Absorbed Power: 0.59 HP * Brake Rotor Diameter 24 in (chosen based on Drum OD) 6 Figure 2. Top: a photo of the winch frame, drum and shaft...shaft for field assembly. Studs welded into the drum , engage keyhole slots in the brake rotor, allowing drum torque to be transferred directly to the

16. View into interior steam spaces of boiler above fireboxes ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

16. View into interior steam spaces of boiler above fireboxes through manhole (see photo VT-14-16 for manhole location). Tops-or crown sheets--of fireboxes show below. Vertical and inclined bars are stays used to hold boiler together and reinforce flat plates under pressure. Note water level used in boilers indicated by scale encrustation on stays. (Threaded stud in extreme foreground belongs to manhole cover opened for purposed of photography.) - Ferry TICONDEROGA, Route 7, Shelburne, Chittenden County, VT

DOE ZERH Case Study: BrightLeaf Homes, McCormick Avenue, Brookfield, IL

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2015-09-01

Case study of a DOE 2015 Housing Innovation Award winning production home in the cold climate that got a HERS 38 without PV, with staggered 2x4 studs every 8”on a 2x6 plate with dense-packed R-25 cellulose, basement with 3” XPS exterior and 2: XPS under slab; a vented attic with spray foam top plates and R-60 blown cellulose; 96% AFUE furnace, 14 SEER AC, plus fresh air intake.

Low Cost Motor Demonstration Program. Volume 1

DTIC Science & Technology

1977-02-01

and held in place by engaging a head end stud (with O-ring) in the igniter cavity in the forward end of the mandrel. The fins on the mandrel used...object. Even if the chunk had been burning when it first appeared, it was extinguished by the time it hit the con- crete and asphalt pavement just...outside the test cell. Impact marks on the chunk were not smoothed by subsequent burning and pieces of loose asphalt were ernbeded in the chunk

Field Testing and Load Rating Report, Bridge S-1090

DTIC Science & Technology

2008-05-01

alignment to the road- way. The steel beams are rolled sections with cover plates welded to the bottom flange. Shear stud connectors were specified...live-load and superimposed dead-loads. In this case, there was no wearing surface on the bridge, and all dead-loads were applied to the...and live-load at Section G_Standard MCap 1021.9 kN-m Superimposed dead-load applied to composite model— wearing surface and railing DW 0.0 kN-m

Field Testing and Load Rating Report, Bridge S-4360, Camp Hovey, South Korea

DTIC Science & Technology

2008-07-01

different section properties than the original six beam-lines. Shear stud connectors were specified on the design plans, indicating the deck was to be...the roadway wearing surface, the railings, and the conduits suspended from the bridge. Since the shear capacities were dependent only on the steel...load and live-load at Section G_Standard MCap 808.7 kN-m Superimposed dead-load applied to composite model— wearing surface and railing DW 75.69 kN

InxGa1-xSb Channel p-Metal-Oxide-Semiconductor Field Effect Transistors: Effect of Strain and Heterostructure Design

DTIC Science & Technology

2011-07-06

biaxial compressive strain is known to split the light- and heavy-hole bands, reducing the interband scattering and causing the light hole band to move up...and heterostructure design are presented. In Section V, we use temperature- dependent measurements and pulsed I-V measurements to analyze the results...minimal in our devices. The temperature dependence of hole mobility was stud- ied for both the surface and buried channel devices, as plot- ted in Fig

Books in Action: Armed Services Editions

DTIC Science & Technology

1984-01-01

were several omissions the army felt were "regrettable," particularly James Farrell’s Studs Lonigan .’ The Armed Services Editions venture was...HERB, editor. Esquire’s First Sports Reader 1284 GRAETO)N, C. W. My Name Is Christopher Nagel -j-277 GRAHAM, FRANK. Lou Gehrig T-2 4 GRAHAM, FRANK. The...Wouldn’t Be in Your Shoes 84.3 IRWIN, MARGARET. Young Bess 1115 ISHERWOOD, CHRISTOPH ER. Prater Violet o-19 JACKSON, CHARL.ES. The Lost Weekend 104 1

NEUTRON SOURCE

DOEpatents

Reardon, W.A.; Lennox, D.H.; Nobles, R.G.

1959-01-13

A neutron source of the antimony--beryllium type is presented. The source is comprised of a solid mass of beryllium having a cylindrical recess extending therein and a cylinder containing antimony-124 slidably disposed within the cylindrical recess. The antimony cylinder is encased in aluminum. A berylliunn plug is removably inserted in the open end of the cylindrical recess to completely enclose the antimony cylinder in bsryllium. The plug and antimony cylinder are each provided with a stud on their upper ends to facilitate handling remotely.

Equine viral arteritis in breeding and sport horses in central Spain.

PubMed

Cruz-Lopez, Fatima; Newton, Richard; Sanchez-Rodriguez, Ana; Ireland, Joanne; Mughini-Gras, Lapo; Moreno, Miguel A; Fores, Paloma

2017-12-01

Equine viral arteritis (EVA) may have a high economic impact on breeding stud farms due to the occurrence of EVA-associated abortion outbreaks and the ability of the virus to persist in carrier stallions. While the consequences of EVA in premises with sport horses are usually less severe, the first confirmed outbreak of EVA in Spain occurred in a riding club in Barcelona, but no data on the seroprevalence of EVA in sport horses have been reported in Spain. Given the importance of both Spanish Purebred (SP) breeding horses and sport horses for Spain's equine industry, the aim of this study was to determine and compare the seroprevalence of EVA in these two horse populations in central Spain. Serum samples from 155 SP breeding horses residing in 16 stud farms and 105 sport horses of different breeds housed in 12 riding clubs, collected between September 2011 and November 2013, were tested using a commercial EVA antibody ELISA test with a 100% sensitivity, and confirmed by seroneutralisation (SN) test. EVA seroprevalence in SP breeding horses was higher 21.1% (95% CI 15.3-26.8%) than that in sport horses (6.7%, 95% CI 1.89-11.45%). However, the primary use (breeding vs. sport) was not significantly associated with seropositivity to Equine Arteritis Virus (EAV), suggesting that different management factors do not affect EVA circulation in these two horse populations. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effects on boar semen quality after infection with porcine reproductive and respiratory syndrome virus: a case report

PubMed Central

2013-01-01

The effect of porcine reproductive and respiratory syndrome virus (PRRSV) on semen quality was examined in a group of 11 spontaneously infected boars in a commercial boar stud. Semen samples were collected 4 weeks prior to 4 weeks post-infection (wpi). Infection with PRRSV of the European genotype subtype 1 (EU-1) was verified by specific quantitative real-time polymerase chain reaction (RT-PCR) in 36% of the serum samples. All boars seroconverted before 4 wpi and remained in normal condition throughout the study. Comparison of the percentage of morphologically intact spermatozoa revealed an increase of acrosome-defective spermatozoa (P = 0.012) between −4 and 4 wpi. Significant deleterious effects on semen quality were detected for membrane integrity when semen had been stored for 2 days after sampling. Analysis of sperm subpopulations in a thermoresistance test on day 7 after sampling revealed alterations in the percentage of circular, progressively motile spermatozoa (P = 0.013), in the percentage of non-linear, progressively motile spermatozoa (P = 0.01), and on the amplitude of lateral sperm head displacement (P = 0.047). There was no difference in the incidence of mitochondrially active spermatozoa (P = 0.075). Investigation of routine production data between pre- and post-infection status showed no differences on ejaculate volume (P = 0.417), sperm concentration (P = 0.788), and percentage of motile spermatozoa (P = 0.321). This case report provides insights into a potential control strategy for PRRSV outbreaks in boar studs. PMID:23442207

SM-1 REACTOR VESSEL COVER AND FLANGE STRESS ANALYSIS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sayre, M.F.

1962-02-19

The maximum stress calculated for the SMl-1 reactor vessel closure studs occurs during operation at full power. This value is 27,180 psi of which 19,800 psi is tension and 7380 psi bending. This stress does not include a stress concentration factor for effect of threads. It was eonservatively assumed the studs were initially tightened to a code allowable stress of 20,000 psi as specified in the ASME Code rather than the lesser stress obtained by the normal operating procedure. The maximum calculated stress occurs at the outside surface of the cover where the stress ranges from 318 psi in tensionmore » to 90,660 psi in compression. The alternating stress is 50,000 psi. According to the Navy Code for a stress range of 50,000 psi, the eover material ean safely undergo a maximum of 1600 cycles. It was estimated that the SM-1 will go through approximately 000 startup and shutdown cycles during a 20-yr life period, so the calculated stress is regarded as safe. For a transient eondition of 30 deg F/hr during heat-up, approximate temperature differences between the inside and outside surfaces of the cover were obtained. Temperature differentials between the inside and outside surfaces of the cover are increased by roughly 10%; above the steady state condition. More exact calculations of the transient stresses did not appear necessary siuce they would be not more than 10% greater than the steady state thermal stress. (auth)« less

Heating equipment installation system

DOEpatents

Meuschke, Robert E.; Pomaibo, Paul P.

1991-01-01

A method for installing a heater unit assembly (52, 54) in a reactor pressure vessel (2) for performance of an annealing treatment on the vessel (2), the vessel (2) having a vertical axis, being open at the top, being provided at the top with a flange (6) having a horizontal surface, and being provided internally, at a location below the flange (6), with orientation elements (8) which are asymmetrical with respect to the vertical axis, by the steps of: providing an orientation fixture (10) having an upwardly extending guide member (18) and orientation elements (14, 16) and installing the orientation fixture (10) in the vessel (2) so that the orientation elements (14,16) of the orientation fixture (10) mate with the orientation elements (8) of the pressure vessel (2) in order to establish a defined position of the orientation fixture (10) in the pressure vessel (2), and so that the guide member (18) projects above the pressure vessel (2) flange (6); placing a seal ring (30) in a defined position on the pressure vessel (2) flange (6) with the aid of the guide member (18); mounting at least one vertical, upwardly extending guide stud (40) upon the seal ring (30); withdrawing the orientation fixture (10) from the pressure vessel (2); and moving the heater unit assembly (52,54) vertically downwardly into the pressure vessel (2) while guiding the heater unit assembly (52,54) along a path with the aid of the guide stud (40).

Puncturing the Counterinsurgency Myth: Britain and Irregular Warfare in the Past, Present, and Future

DTIC Science & Technology

2011-09-01

Academy also concedes that, in relation to Northern Ireland, “[ I ]t is easy in the light of the later success . . . to for- get the early mistakes and the...publicized incidents in Iraq, such as the death in Brit- ish custody of Basra hotel clerk Baha Mousa in 2003 and the subsequent court-martial of the...exemplars of COIN warfare. It can now look at An- bar province and the Surge as the new ideal case stud- ies in COIN textbooks. The Americans have

The Challenge of Violent Drug-Trafficking Organizations: An Assessment of Mexican Security Based on Existing RAND Research on Urban Unrest, Insurgency, and Defense-Sector Reform

DTIC Science & Technology

2011-01-01

Bad Factors Outcome Afghanistan (post-Soviet) 0 10 –10 Loss Somalia 1 10 –9 Loss Chechnya I 2 10 –8 Loss Rwanda 2 10 –8 Loss Zaire (anti-Mobutu) 0...most of Baha California (Norte/Sur), Sonora, Chihuahua, Durango, Sinaloa, Nayarit, Jalisco, Colima, Quintana Roo, Yucatan, Campeche, Zacatecas...Sources of Success in Counterinsurgency and Victory Has a Thousand Fathers: Detailed Counterinsurgency Case Stud- ies . For that study, the research

Multiple Cationic Amphiphiles Induce a Niemann-Pick C Phenotype and Inhibit Ebola Virus Entry and Infection

DTIC Science & Technology

2013-02-18

genome replication and production of new virions [18]. Several cellular proteins required for the function and maturation of late endosomes (LE) and...studded with a trimeric glycoprotein (GP) whose first function is to attach viral particles to the cell surface. The virions are then internalized into the...with NPC1, but at a site distinct from the C loop of NPC1 (which binds GP19 kDa). Binding to NPC1 inhibits a second function of NPC1 (i.e. in addition

Tarnished Armor Erosion of Military Ethics

DTIC Science & Technology

1988-03-23

UNCLASSIFC-ED ?JSAWC MILITAFY STUD’ FS PROGRA.M PAPER Th4 vlev: expressed La th 028paPer are thane of the"athor antd do Vot Dece~ssacl 7 reflect the...NDTV7DUA1L STUDY PROjECT bitoF byAvIbit Lieutenant Colonel Bruce Allen M4a~ sOn , Eli Colonel Timothy Tatum ?roject Adv;iser DISTRIZUTtff STATU=~ At APPIOVeC...activity began to ener,. a od; de was associated with a personage who ultimately becare a ,a p4ayir in the ’ark intrigue. Soon there was connectivity, and

Maco/Micro Studies of Hydrogen Embrittlement Mechanisms in Titanium and Aluminum Alloys.

DTIC Science & Technology

1981-04-01

DISTRIBUTION STATEMENT (.frhe .,bstf-f: - te-.J ’ h/’ 4 J .0 d lfr n, /5,po IS. SUPPLEMENTARY N3TES a Hydrogen Embrittlement, Titanium Alloys, Aluminum...AD-A116 025 MINNESOTA U4IV MINNEAPOLIS F/ 6 11/ 6 NACO/MICRO STUD~IES OF HYDRO6EN ENORITTLEMENT MECHANISMS IN TITA--CYCCUD APR 81 W W GERBERICH AFOSR77...HYDROGEN EMBRITTLEMENT MECHANSIMS IN TITANIUM AND ALUMINUM ALLOYS FINAL REPORT for Period October 1975 to October 1981 4M University of Minnesota Minneapolis

Maintenance of fertility in the horse including artificial insemination.

PubMed

Frhr, J; Lepel, V

1975-04-01

A high fertility rate depends on many different factors and is always related to inheritance and enviorment. The successful feritly control system in the German Thoroughbred breeding industry shows that fertility can be increased by good management and veterinary supervision. The insemination of horses with frozen semen is discussed. Replacement of natural service by A.I. with frozen semen is not generally accepted in horsebreeding, as the conditions are entirely different from cattle breeding. However, there are several ways in which A.I. can be assistance in stud management.

A Brief Survey of the Mosquitoes of South Sulawesi, Indonesia, with Special Reference to the Identity of ’Anopheles barbirostris’ (Diptera: Culicidae) from the Margolembo Area

DTIC Science & Technology

1977-06-20

mosquitoes hitherto recorded from Sulawesi and adjacent islands is presented. The prevalence of malaria and filariasis in transmigration villages of...East Indian mosquitoes. Bull. Ent. Res. 25: 501-19, illus. 1939. Notes on Dutch East- Indian mosquitoes. Tij&hr. Ent. 82: 91-113, illus. Brug, S...Macdonald, W. W. 1957. Malaysian parasites. XVI. An interim review of the non-anopheline mosquitoes of Malaya. Stud. Inst. Med. Res., Malaya 28: l-34

Benefit/Cost Analysis of Interdwelling Noise Control in Multifamily Dwellings

DTIC Science & Technology

1991-12-01

Monterey Pines was tested by Owens / Corning Fiberglas in 1966 and produced a laboratory STC rating of 46 (see Figure 1). This rating is approximately...As an example, tests performed by Owens / Corning Fiberglas found the same assembly can have a 12 point increase in IIC when the 50 oz. carpet and 24 oz...the 2" wool batt insulation originally specified (see Figure 14). [Ref. 67] 1. 2. 3. 4. 1. 2x4 studs spaced 24"o.c. and staggered ... Owens / Corning 12

3D-Printing ‘Smarter’ Energy Absorbing Materials

ScienceCinema

Duoss, Eric

2018-01-16

Foams are, by nature, disordered materials studded with air pockets of varying sizes. Lack of control over the material’s architecture at the micrometer or nanometer scale can make it difficult to adjust the foam’s basic properties. But Eric Duoss and a team of Livermore researchers are using additive manufacturing to develop “smarter” silicone cushions. By architecting the structure at the micro scale, they are able to control macro-scale properties previously unachievable with foam materials.

Coffee straw can replace Hader bar for bar retained overdentures--a clinical report.

PubMed

Guttal, S S; Shetty, U S

2012-12-01

Bar attachment system provides retention and support for the overdenture. Retention of a mandibular denture can be achieved by an implant-retained or natural tooth-retained bar and stud attachment in the anterior segment of the mandible. A simple and cost effective treatment for more complex implant overdenture is the concept of conventional tooth-retained overdentures. The authors present a clinical report of a patient treated with a mandibular tooth-borne overdenture with a bar. The bar was fabricated using a coffee straw.

Field Testing and Load Rating Report, Bridge FSBR-514, Fort Shafter, Hawaii

DTIC Science & Technology

2009-05-01

composite model – wearing surface and railing DW 5.95 kip-in./in. Live load effect (HS-20) LL 8.55 kip-in./in. Resistance factor for steel in...and live load at Interior Beam. MCap 51.1 Kip-in/in Superimposed dead load applied to composite model – wearing surface and railing DW 5.88...with concrete studs . If the above steps are followed, it should be possible to mount each trans- ducer in approximately 5 to 10 min. The Figures C1

Evaluation of Synthetic Fuel for Army Ground Applications Tasks II-VI

DTIC Science & Technology

2007-06-29

84760 22937 20 PABZZ 5325005981428 84760 10445 21 D.BZZ 84760 27002 21 D.BZZ 84760 28861 22 PABZZ 5315008871539 84760 11141 23 PABZZ 3040011883242...SUPERSEDES: EDmON NO.: 15 DATED: OT-31-0S DEPT. OF DEFSNSE (1.2 CST MIN. FUEL) NOTE; THIS SPECIFICATION DEVt:LOPED WITH ISO LONG INI. t:T STUD... ISO 4093: .083" (1.6 mmliD X 25" {636 mml LONG. 2. CAUSRATIN~ INJECTORS ........ ’SAE Jlii66/ ISO 7440: 0.5 mm ORIFICE PLATE NOP: 3000 PSI (207 &ARl

HIV envelope glycoprotein imaged at high resolution | Center for Cancer Research

Cancer.gov

The outer surface of the human immunodeficiency virus (HIV) is surrounded by an envelope studded with spike-shaped glycoproteins called Env that help the deadly virus identify, bind, and infect cells. When unbound, Env exists in a “closed” conformational state. Upon binding with target cells, such as CD4+ T cells, the protein transitions to an “open” configuration. Given that Env is the only viral protein expressed on HIV’s surface, knowing its detailed structure—especially in the unbound state—may be critical for designing antibodies and vaccines against HIV.

An Investigation of Methods to Measure and Predict Biological and Physical Effects of Commercial Navigation Traffic: Workshop II Held in St. Louis, Missouri on 17-18 April 1990

DTIC Science & Technology

1991-04-01

task of measurinig these forces in the natural environment and the increasing need to predict how these forces will ultimately affect the environment...near and beneath a towboat are complex and three-dimensional. These flow conditions are affected by physical conditions such as the shape and size of...a highly quantitative and fruitful line of pure and applied stud- ies of aquatic animal life histories (e.g., Russell Hunter (1953), Fremling (1960

Proceedings of the International Congress/Actes du 6eme Congres International (6th) Held in Nice, France on 5-9 July 1993: Noise as a Public Health Problem. Volume 2

DTIC Science & Technology

1993-07-09

exploratory field stud ........................................................................ 389 Leobon A The cartography of a urban center soundscape ...Inter-Noise 91, Sydney 2-4 december 1991. 392 THE CARTOGRAPHY OF A URBAN CENTER SOUNDSCAPE LEOBON Alain C.N.R.S. U.R.A 879 LABORATOIRE DE MECANIQUE...GROUPE "ACOUSTIQUE ARCHITECTURALE ET URBAINE" LE VAL JOYEUX CD.1M - 78450 VILLEPREUX. Tel: (33) (1).30.56.04.16 Summery: While using a town soundscape

Particles from wood smoke and road traffic differently affect the innate immune system of the lung.

PubMed

Samuelsen, Mari; Cecilie Nygaard, Unni; Løvik, Martinus

2009-09-01

The effect of particles from road traffic and wood smoke on the innate immune response in the lung was studied in a lung challenge model with the intracellular bacterium Listeria monocytogenes. Female Balb/cA mice were instilled intratracheally with wood smoke particles, particles from road traffic collected during winter (studded tires used; St+), and during autumn (no studded tires; St-), or diesel exhaust particles (DEP). Simultaneously with, and 1 or 7 days after particle instillation, 10(5) bacteria were inoculated intratracheally. Bacterial numbers in the lungs and spleen 1 day after Listeria challenge were determined, as an indicator of cellular activation. In separate experiments, bronchoalveolar lavage (BAL) fluid was collected 4 h and 24 h after particle instillation. All particles tested reduced the numbers of bacteria in the lung 24 h after bacterial inoculation. When particles were given simultaneously with Listeria, the reduction was greatest for DEP, followed by St+ and St-, and least for wood smoke particles. Particle effects were no longer apparent after 7 days. Neutrophil numbers in BAL fluid were increased for all particle exposed groups. St+ and St- induced the highest levels of IL-1beta, MIP-2, MCP-1, and TNF-alpha, followed by DEP, which induced no TNF-alpha. In contrast, wood smoke particles only increased lactate dehydrogenase (LDH) activity, indicating a cytotoxic effect of these particles. In conclusion, all particles tested activated the innate immune system as determined with Listeria. However, differences in kinetics of anti-Listeria activity and levels of proinflammatory mediators point to cellular activation by different mechanisms.

Generation of urban road dust from anti-skid and asphalt concrete aggregates.

PubMed

Tervahattu, Heikki; Kupiainen, Kaarle J; Räisänen, Mika; Mäkelä, Timo; Hillamo, Risto

2006-04-30

Road dust forms an important component of airborne particulate matter in urban areas. In many winter cities the use of anti-skid aggregates and studded tires enhance the generation of mineral particles. The abrasion particles dominate the PM10 during springtime when the material deposited in snow is resuspended. This paper summarizes the results from three test series performed in a test facility to assess the factors that affect the generation of abrasion components of road dust. Concentrations, mass size distribution and composition of the particles were studied. Over 90% of the particles were aluminosilicates from either anti-skid or asphalt concrete aggregates. Mineral particles were observed mainly in the PM10 fraction, the fine fraction being 12% and submicron size being 6% of PM10 mass. The PM10 concentrations increased as a function of the amount of anti-skid aggregate dispersed. The use of anti-skid aggregate increased substantially the amount of PM10 originated from the asphalt concrete. It was concluded that anti-skid aggregate grains contribute to pavement wear. The particle size distribution of the anti-skid aggregates had great impact on PM10 emissions which were additionally enhanced by studded tires, modal composition, and texture of anti-skid aggregates. The results emphasize the interaction of tires, anti-skid aggregate, and asphalt concrete pavement in the production of dust emissions. They all must be taken into account when measures to reduce road dust are considered. The winter maintenance and springtime cleaning must be performed properly with methods which are efficient in reducing PM10 dust.

Wear particles from studded tires and granite pavement induce pro-inflammatory alterations in human monocyte-derived macrophages: a proteomic study.

PubMed

Karlsson, Helen; Lindbom, John; Ghafouri, Bijar; Lindahl, Mats; Tagesson, Christer; Gustafsson, Mats; Ljungman, Anders G

2011-01-14

Airborne particulate matter is considered to be one of the environmental contributors to the mortality in cancer, respiratory, and cardiovascular diseases. For future preventive actions, it is of major concern to investigate the toxicity of defined groups of airborne particles and to clarify their pathways in biological tissues. To expand the knowledge beyond general inflammatory markers, this study examined the toxicoproteomic effects on human monocyte derived macrophages after exposure to wear particles generated from the interface of studded tires and a granite-containing pavement. As comparison, the effect of endotoxin was also investigated. The macrophage proteome was separated using two-dimensional gel electrophoresis. Detected proteins were quantified, and selected proteins were identified by matrix-assisted laser desorption/ionization time of flight mass spectrometry. Among analyzed proteins, seven were significantly decreased and three were increased by exposure to wear particles as compared to unexposed control cells. Endotoxin exposure resulted in significant changes in the expression of six proteins: four decreased and two increased. For example, macrophage capping protein was significantly increased after wear particle exposure only, whereas calgizzarin and galectin-3 were increased by both wear particle and endotoxin exposure. Overall, proteins associated with inflammatory response were increased and proteins involved in cellular functions such as redox balance, anti-inflammatory response, and glycolysis were decreased. Investigating the effects of characterized wear particles on human macrophages with a toxicoproteomic approach has shown to be useful in the search for more detailed information about specific pathways and possible biological markers.

Chemical Laws, Idealization and Approximation

NASA Astrophysics Data System (ADS)

Tobin, Emma

2013-07-01

This paper examines the notion of laws in chemistry. Vihalemm ( Found Chem 5(1):7-22, 2003) argues that the laws of chemistry are fundamentally the same as the laws of physics they are all ceteris paribus laws which are true "in ideal conditions". In contrast, Scerri (2000) contends that the laws of chemistry are fundamentally different to the laws of physics, because they involve approximations. Christie ( Stud Hist Philos Sci 25:613-629, 1994) and Christie and Christie ( Of minds and molecules. Oxford University Press, New York, pp. 34-50, 2000) agree that the laws of chemistry are operationally different to the laws of physics, but claim that the distinction between exact and approximate laws is too simplistic to taxonomise them. Approximations in chemistry involve diverse kinds of activity and often what counts as a scientific law in chemistry is dictated by the context of its use in scientific practice. This paper addresses the question of what makes chemical laws distinctive independently of the separate question as to how they are related to the laws of physics. From an analysis of some candidate ceteris paribus laws in chemistry, this paper argues that there are two distinct kinds of ceteris paribus laws in chemistry; idealized and approximate chemical laws. Thus, while Christie ( Stud Hist Philos Sci 25:613-629, 1994) and Christie and Christie ( Of minds and molecules. Oxford University Press, New York, pp. 34--50, 2000) are correct to point out that the candidate generalisations in chemistry are diverse and heterogeneous, a distinction between idealizations and approximations can nevertheless be used to successfully taxonomise them.

Thermotemporal dynamics of contaminant bacteria and antimicrobials in extended porcine semen.

PubMed

Althouse, G C; Pierdon, M S; Lu, K G

2008-11-01

Bacterial contamination of extended porcine semen has been associated with deleterious effects on both semen quality and sow fertility. Retrospective, prospective and in vitro studies were performed to delineate the prevalence and behavior of certain bacterial contaminants in extended semen, and antimicrobial pharmacodynamics in various semen diluents. Retrospective review of extended semen samples submitted from North American boar studs for microbiological screening at the University of Pennsylvania Reference Andrology Laboratory in 2005 and 2006 yielded bacteriospermia prevalence rates of 17% (144/832) and 26% (256/984), respectively. In a prospective study of regional boar studs, of 91 extended semen samples tested over 1-y, 29% were positive for bacteriospermia. Retrospective and prospective studies both showed that the preponderance of contaminant positive samples occurred during the fall months (P<0.05). To better understand behavior of select contaminant bacteria, generation intervals were determined for Serratia marcescens (SM) and Achromobacter xylosoxidans (AX) at 16, 22 and 37 degrees C. Generation times were temperature-dependent, with intervals decreasing two- to four-fold as incubation temperature increased. Growth patterns for SM, AX and Burkholderia cepacia were evaluated in various semen diluents. The different diluents exhibited constant or episodic patterns of growth within and among bacteria throughout the 5-d test period. Kill-time kinetics at 37 degrees C of several genera of bacteria in four semen diluents containing amoxicillin, gentamicin, tylosin, and lincomycin/spectinomycin (single drug or combination) ranged from 75 to over 360min, and was highly dependent (P<0.05) upon both type of bacteria and semen diluent.

Development of a 3D finite element acoustic model to predict the sound reduction index of stud based double-leaf walls

NASA Astrophysics Data System (ADS)

Arjunan, A.; Wang, C. J.; Yahiaoui, K.; Mynors, D. J.; Morgan, T.; Nguyen, V. B.; English, M.

2014-11-01

Building standards incorporating quantitative acoustical criteria to ensure adequate sound insulation are now being implemented. Engineers are making great efforts to design acoustically efficient double-wall structures. Accordingly, efficient simulation models to predict the acoustic insulation of double-leaf wall structures are needed. This paper presents the development of a numerical tool that can predict the frequency dependent sound reduction index R of stud based double-leaf walls at one-third-octave band frequency range. A fully vibro-acoustic 3D model consisting of two rooms partitioned using a double-leaf wall, considering the structure and acoustic fluid coupling incorporating the existing fluid and structural solvers are presented. The validity of the finite element (FE) model is assessed by comparison with experimental test results carried out in a certified laboratory. Accurate representation of the structural damping matrix to effectively predict the R values are studied. The possibilities of minimising the simulation time using a frequency dependent mesh model was also investigated. The FEA model presented in this work is capable of predicting the weighted sound reduction index Rw along with A-weighted pink noise C and A-weighted urban noise Ctr within an error of 1 dB. The model developed can also be used to analyse the acoustically induced frequency dependent geometrical behaviour of the double-leaf wall components to optimise them for best acoustic performance. The FE modelling procedure reported in this paper can be extended to other building components undergoing fluid-structure interaction (FSI) to evaluate their acoustic insulation.

Stud Walls With Continuous Exterior Insulation for Factory Built Housing: New York, New York (Fact Sheet), NREL (National Renewable Energy Laboratory)

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

The Advanced Envelope Research effort will provide factory homebuilders with high performance, cost-effective alternative envelope designs. In the near term, these technologies will play a central role in meeting stringent energy code requirements. For manufactured homes, the thermal requirements, last updated by statute in 1994, will move up to the more rigorous IECC 2012 levels in 2013, the requirements of which are consistent with site built and modular housing. This places added urgency on identifying envelope technologies that the industry can implement in the short timeframe. The primary goal of this research is to develop wall designs that meet themore » thermal requirements based on 2012 IECC standards. Given the affordable nature of manufactured homes, impact on first cost is a major consideration in developing the new envelope technologies. This work is part of a four-phase, multi-year effort. Phase 1 identified seven envelope technologies and provided a preliminary assessment of three selected methods for building high performance wall systems. Phase 2 focused on the development of viable product designs, manufacturing strategies, addressing code and structural issues, and cost analysis of the three selected options. An industry advisory committee helped critique and select the most viable solution to move further in the research - stud walls with continuous exterior insulation. Phase 3, the subject of the current report, focused on the design development of the selected wall concept and explored variations on the use of exterior foam insulation. The scope also included material selection, manufacturing and cost analysis, and prototyping and testing.« less

Technology Solutions Case Study: Stud Walls with Continuous Exterior Insulation for Factory Built Housing

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

The Advanced Envelope Research effort will provide factory homebuilders with high performance, cost-effective alternative envelope designs. In the near term, these technologies will play a central role in meeting stringent energy code requirements. For manufactured homes, the thermal requirements, last updated by statute in 1994, will move up to the more rigorous IECC 2012 levels in 2013, the requirements of which are consistent with site built and modular housing. This places added urgency on identifying envelope technologies that the industry can implement in the short timeframe. The primary goal of this research is to develop wall designs that meet themore » thermal requirements based on 2012 IECC standards. Given the affordable nature of manufactured homes, impact on first cost is a major consideration in developing the new envelope technologies. This work is part of a four-phase, multi-year effort. Phase 1 identified seven envelope technologies and provided a preliminary assessment of three selected methods for building high performance wall systems. Phase 2 focused on the development of viable product designs, manufacturing strategies, addressing code and structural issues, and cost analysis of the three selected options. An industry advisory committee helped critique and select the most viable solution to move further in the research — stud walls with continuous exterior insulation. Phase 3, the subject of the current report, focused on the design development of the selected wall concept and explored variations on the use of exterior foam insulation. The scope also included material selection, manufacturing and cost analysis, and prototyping and testing.« less

Navigating the fine line between benefit and risk in chronic atrial fibrillation: rationale and design of the Standard versus Atrial Fibrillation spEcific managemenT studY (SAFETY).

PubMed

Carrington, Melinda J; Ball, Jocasta; Horowitz, John D; Marwick, Thomas H; Mahadevan, Gnanadevan; Wong, Chiew; Abhayaratna, Walter P; Haluska, Brian; Thompson, David R; Scuffham, Paul A; Stewart, Simon

2013-06-20

Health outcomes associated with atrial fibrillation (AF) continue to be poor and standard management often does not provide clinical stability. The Standard versus Atrial Fibrillation spEcific managemenT studY (SAFETY) compares the efficacy of a post-discharge, nurse-led, multi-disciplinary programme to optimise AF management with usual care. SAFETY is a prospective, multi-centre, randomised controlled trial with blinded-endpoint adjudication. A target of 320 hospitalised patients with a chronic form of AF will be randomised (stratified by "rate" versus "rhythm" control) to usual post-discharge care or the SAFETY Intervention (SI). The SI involves home-based assessment, extensive clinical profiling and the application of optimal gold-standard pharmacology which is individually tailored according to a "traffic light" framework based on clinical stability, risk profile and therapeutic management. The primary endpoint is event-free survival from all-cause death or unplanned readmission during 18-36 months follow-up. Secondary endpoints include rate of recurrent hospital stay, treatment success (i.e. maintenance of rhythm or rate control and/or application of anti-thrombotic therapy without a bleeding event) and cost-efficacy. With study recruitment to be completed in early 2012, the results of this study will be available in early 2014. If positive, SAFETY will represent a potentially cost-effective and readily applicable strategy to improve health outcomes in high risk individuals discharged from hospital with chronic AF. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

The structure, dynamics and movement patterns of the Australian sheep industry.

PubMed

East, I J; Foreman, I

2011-12-01

To describe the structure of Australia's sheep industries and the movement of sheep to enable examination of the potential for animal movements to spread disease between farms. The structure, size, marketing and movement patterns of Australian sheep farms was determined through (i) review of data published by the Australian Bureau of Statistics and Australian Bureau of Agricultural and Resource Economics, (ii) interviews with producers and saleyard managers and (iii) expert opinion. Twelve geographic regions are described, based on the type and extent of sheep farming in each region. Five production sectors were identified within the Australian sheep industry, with the proportion of each varying between the geographic regions. Over the past 20 years, the industry has decreased in size and contracted from the northern and central areas of Australia. Movement of sheep onto the majority (79%) of properties was limited to the introduction of less than 50 stud rams annually, although cross-bred- and wether-based farms introduced up to 2000 sheep annually; 75% of sheep movements occurred over distances less than 200 km, but stud rams moved up to 500 km. An increasing percentage of movements off farms was direct to abattoirs and over 80% of sheep sold through saleyards were purchased by abattoirs. The majority of Australian sheep farms operate as self-replacing enterprises and introduce few stock. In addition, most sheep movements occur over distances of less than 200 km and therefore sheep movements within Australia have only a limited potential to spread disease over larger distances. © 2011 The Authors. Australian Veterinary Journal © 2011 Australian Veterinary Association.

An ultramicroscopic study on rigor mortis.

PubMed

Suzuki, T

1976-01-01

Gastrocnemius muscles taken from decapitated mice at various intervals after death and from mice killed by 2,4-dinitrophenol or mono-iodoacetic acid injection to induce rigor mortis soon after death, were observed by electron microscopy. The prominent appearance of many fine cross striations in the myofibrils (occurring about every 400 A) was considered to be characteristic of rigor mortis. These striations were caused by minute granules studded along the surfaces of both thick and thin filaments and appeared to be the bridges connecting the 2 kinds of filaments and accounted for the hardness and rigidity of the muscle.

Dreaming and immanence: rejecting the dogmatic image of thought in science education

NASA Astrophysics Data System (ADS)

Bazzul, Jesse; Wallace, Maria F. G.; Higgins, Marc

2018-02-01

In this article, we, a multivocal-thinking-assemblage, trouble what we feel is the dogmatic image of thought in science education. Beginning with Lars Bang's (Cult Stud Sci Educ, 2017) dramatic and disruptive imagery of the Ouroboros as a means to challenge scientific literacy we explore the importance of dreams, thinking with both virtual and actual entities, and immanent thinking to science education scholarship. Dreaming as movement away from a dogmatic image of thought takes the authors in multiple directions as they attempt to open Deleuzian horizons of difference, immanence, and self-exploration.

Synchronous Pulmonary Malignancies: Atypical Presentation of Mantle Cell Lymphoma Masking a Lung Malignancy

PubMed Central

Masha, Luke; Zinchuk, Andrey; Boosalis, Valia

2015-01-01

We present a case of a pleural space malignancy masked by an atypical presentation of mantle cell lymphoma. Our patient presented with a large pleural effusion and right sided pleural studding, initially attributed to a new diagnosis of mantle cell lymphoma. Rare atypical epithelial cells were also seen amongst the clonal population of lymphocytes. The patient lacked systemic manifestations of mantle cell lymphoma and did not improve with chemotherapy. A pleural biopsy ultimately revealed the presence of an undifferentiated carcinoma, favoring a lung primary. A discussion of synchronous pleural space malignancies involving lymphomas is given. PMID:26500732

Synchronous Pulmonary Malignancies: Atypical Presentation of Mantle Cell Lymphoma Masking a Lung Malignancy.

PubMed

Masha, Luke; Zinchuk, Andrey; Boosalis, Valia

2015-09-07

We present a case of a pleural space malignancy masked by an atypical presentation of mantle cell lymphoma. Our patient presented with a large pleural effusion and right sided pleural studding, initially attributed to a new diagnosis of mantle cell lymphoma. Rare atypical epithelial cells were also seen amongst the clonal population of lymphocytes. The patient lacked systemic manifestations of mantle cell lymphoma and did not improve with chemotherapy. A pleural biopsy ultimately revealed the presence of an undifferentiated carcinoma, favoring a lung primary. A discussion of synchronous pleural space malignancies involving lymphomas is given.

Pilot cryo tunnel: Attachments, seals, and insulation

NASA Technical Reports Server (NTRS)

Wilson, J. F.; Ware, G. D.; Ramsey, J. W., Jr.

1974-01-01

Several different tests are described which simulated the actual configuration of a cryogenic wind tunnel operating at pressures up to 5 atmospheres (507 kPa) and temperatures from -320 F (78K) to 120 F (322K) in order to determine compatible bolting, adequate sealing, and effective insulating materials. The evaluation of flange attachments (continuous threaded studs) considered bolting based on compatible flanges, attachment materials, and prescribed bolt elongations. Various types of seals and seal configurations were studied to determine suitability and reusability under the imposed pressure and temperature loadings. The temperature profile was established for several materials used for structural supports.

Best Practices Case Study: David Weekley Homes - Eagle Springs and Waterhaven, Houston, TX

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2011-04-01

Case study describing David Weekley Homes, Houston Division, has qualified more than 1,240 homes for the DOE Builders Challenge. Advanced framed 2x6 walls with open headers and two-stud corners allow more room for R-20 damp sprayed cellulose wall cavity insulation that is covered with R-5 rigid XPS foam. A radiant barrier cuts heat gain in the R-38 insulated vented attics. Draft stopping at fireplace and duct chases and behind tubs, gluing sheetrock to framing, and extensive caulking make for air-tight homes at 3.0 ACH50.

Incomplete Kochen-Specker coloring

NASA Astrophysics Data System (ADS)

Granström, Helena

2007-09-01

A particular incomplete Kochen-Specker coloring, suggested by Appleby [Stud. Hist. Philos. Mod. Phys. 36, 1 (2005)] in dimension three, is generalized to arbitrary dimension. We investigate its effectivity as a function of dimension, using two different measures. A limit is derived for the fraction of the sphere that can be colored using the generalized Appleby construction as the number of dimensions approaches infinity. The second, and physically more relevant measure of effectivity, is to look at the fraction of properly colored ON bases. Using this measure, we derive a "lower bound for the upper bound" in three and four real dimensions.

Achieving an esthetic smile with fixed and removal prosthesis using extracoronal castable precision attachments

PubMed Central

Vaidya, Sharad; Kapoor, Charu; Bakshi, Yujika; Bhalla, Sonam

2015-01-01

Satisfactory restoration in a patient with a partially edentulous situation can be challenging especially when unilateral or bilateral posterior segment of teeth is missing. Successful restoration can be done with various conventional and contemporary treatment options. One such treatment modality is attachment-retained cast partial dentures. A key to success for an attachment retained cast partial denture is the strategic selection of teeth for retention. This clinical report discusses rehabilitation of a patient with the help of a combined prosthesis in the upper arch and stud retained overdenture in the lower arch. PMID:26929527

Safer staining method for acid fast bacilli.

PubMed Central

Ellis, R C; Zabrowarny, L A

1993-01-01

To develop a method for staining acid fast bacilli which excluded highly toxic phenol from the staining solution. A lipophilic agent, a liquid organic detergent, LOC High Studs, distributed by Amway, was substituted. The acid fast bacilli stained red; nuclei, cytoplasm, and cytoplasmic elements stained blue on a clear background. These results compare very favourably with acid fast bacilli stained by the traditional method. Detergents are efficient lipophilic agents and safer to handle than phenol. The method described here stains acid fast bacilli as efficiently as traditional carbol fuchsin methods. LOC High Suds is considerably cheaper than phenol. Images PMID:7687254

Safer staining method for acid fast bacilli.

PubMed

Ellis, R C; Zabrowarny, L A

1993-06-01

To develop a method for staining acid fast bacilli which excluded highly toxic phenol from the staining solution. A lipophilic agent, a liquid organic detergent, LOC High Studs, distributed by Amway, was substituted. The acid fast bacilli stained red; nuclei, cytoplasm, and cytoplasmic elements stained blue on a clear background. These results compare very favourably with acid fast bacilli stained by the traditional method. Detergents are efficient lipophilic agents and safer to handle than phenol. The method described here stains acid fast bacilli as efficiently as traditional carbol fuchsin methods. LOC High Suds is considerably cheaper than phenol.

Vibration characteristics of walls and a plate glass window representative of those of a wood-frame house

NASA Technical Reports Server (NTRS)

Carden, H. D.

1979-01-01

Mechanical excitation was used, and measurements of acceleration response, natural frequencies, and nodal patterns were performed. Results indicate that the wall sections and the complete wall did not act as a unit in responding to sinusoidal vibration inputs. Calculated frequencies of the components that account for this independent behavior of the studs and face sheets agreed resonably well with experimental frequencies. Experimental vibrations of the plate glass window agreed with the calculated behavior, and responses of the window exposed to airplane flyover noise were readily correlated with the test results.

Construcción de un catálogo de cúmulos de galaxias en proceso de colisión

NASA Astrophysics Data System (ADS)

de los Ríos, M.; Domínguez, M. J.; Paz, D.

2015-08-01

In this work we present first results of the identification of colliding galaxy clusters in galaxy catalogs with redshift measurements (SDSS, 2DF), and introduce the methodology. We calibrated a method by studying the merger trees of clusters in a mock catalog based on a full-blown semi-analytic model of galaxy formation on top of the Millenium cosmological simulation. We also discuss future actions for studding our sample of colliding galaxy clusters, including x-ray observations and mass reconstruction obtained by using weak gravitational lenses.

Effect of Steel Framing for Securing Drywall Panels on Thermal and Humidity Parameters of the Outer Walls

NASA Astrophysics Data System (ADS)

Major, Maciej; Kosiń, Mariusz

2017-12-01

The paper analyses the effect of steel framing used to secure drywall panels on thermal and humidity properties of outer walls. In the practice of building a light structure, the most popular components are steel and wood studs. They are used to obtain framing for building a wall (an outer wall in this study). Analysis presented in this study concerned the corner of the outer wall build using the technology of light steel framing. Computer simulation was used to perform thermal and humidity analysis for the joint of the outer wall.

Allergy adjuvant effect of particles from wood smoke and road traffic.

PubMed

Samuelsen, Mari; Nygaard, Unni Cecilie; Løvik, Martinus

2008-04-18

There is growing evidence that in addition to augmenting the severity of asthma and allergic diseases, particulate air pollution also increases the incidence of allergy and asthma. We studied the adjuvant effect of particles from wood smoke and road traffic on the immune response to the allergen ovalbumin (OVA). OVA with and without particles was injected into one hind footpad of Balb/cA mice. All particles together with OVA significantly increased the level of OVA-specific immunoglobulin E (IgE) in serum, compared to groups given OVA or particles alone. Reference diesel exhaust particles (DEP) with OVA induced the highest levels of IgE, whereas no clear difference was observed between particles from road traffic and wood smoke. Road traffic particles collected in the autumn induced higher IgE values with OVA than corresponding particles collected during the winter season when studded tires are used, suggesting that studded tire-generated road pavement particles have less allergy adjuvant activity than exhaust particles. Compared to OVA or particles alone, all particles with OVA increased popliteal lymph node cell numbers, cell proliferation, ex vivo secretion of IL-4 and IL-10 after ConA stimulation, and the expression of several cell surface molecules (CD19, MHC class II, CD86 and CD23). Wood smoke particles with OVA induced somewhat higher cellular responses than road traffic particles, but less than DEP with OVA which seemed to be the most potent particle in inducing cellular as well as antibody responses. Thus, wood smoke particles had about the same capacity to enhance allergic sensitization as road traffic particles, but less than diesel exhaust particles.

Posttest analysis of a 1:6-scale reinforced concrete reactor containment building

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weatherby, J.R.

In an experiment conducted at Sandia National Laboratories, 1:6-scale model of a reinforced concrete light water reactor containment building was pressurized with nitrogen gas to more than three times its design pressure. The pressurization produced one large tear and several smaller tears in the steel liner plate that functioned as the primary pneumatic seal for the structure. The data collected from the overpressurization test have been used to evaluate and further refine methods of structural analysis that can be used to predict the performance of containment buildings under conditions produced by a severe accident. This report describes posttest finite elementmore » analyses of the 1:6-scale model tests and compares pretest predictions of the structural response to the experimental results. Strain and displacements calculated in axisymmetric finite element analyses of the 1:6-scale model are compared to strains and displacement measured in the experiment. Detailed analyses of the liner plate are also described in the report. The region of the liner surrounding the large tear was analyzed using two different two-dimensional finite elements model. The results from these analyzed indicate that the primary mechanisms that initiated the tear can be captured in a two- dimensional finite element model. Furthermore, the analyses show that studs used to anchor the liner to the concrete wall, played an important role in initiating the liner tear. Three-dimensional finite element analyses of liner plates loaded by studs are also presented. Results from the three-dimensional analyses are compared to results from two-dimensional analyses of the same problems. 12 refs., 56 figs., 1 tab.« less

Financial effect of bovine Johne's disease in beef cattle herds in Australia.

PubMed

Webb Ware, J K; Larsen, J W A; Kluver, P

2012-04-01

To assess the financial effect of programs for controlling bovine Johne's disease (BJD) in beef herds. A spreadsheet simulation model of a self-replacing beef herd in south-eastern Australia selling 400-kg steers at 15 months old. The model calculated the monthly cash flow, and net present value (NPV) of cumulative cash flow, over 10 years. Four main control options were compared: (1) a base herd (no action to control the disease), (2) test and cull, and (3) partial and (4) total destocking. It was assumed that BJD was eradicated after 3 and 5 years with total and partial destocking, respectively, and not eradicated with a test and cull program. Scenarios were compared for both commercial and stud enterprises. If there was no discount on the sale price of cattle in commercial herds, deaths from BJD had to exceed 5% before the NPV of partial or total destocking was similar to taking no action to control the disease over a 10-year period. When cattle sales incurred a 10% discount, deaths had to exceed 1% before the destocking strategies would break even after 10 years. Control options for BJD should be carefully planned on an individual herd basis, as significant production and financial risks accompany destocking programs. Eradication will only be more profitable in the longer term, compared with living with the disease, when discounts on the sale of stock from infected herds are high. This can occur with the selling of store cattle or breeders. In stud herds, BJD will usually cause the total failure of the business. © 2012 The Authors. Australian Veterinary Journal © 2012 Australian Veterinary Association.

Single, transcervical insemination using frozen-thawed semen in the Greyhound: a case series study.

PubMed

Pretzer, S D; Lillich, R K; Althouse, G C

2006-04-01

Transcervical insemination (TCI) has generated recent interest as an assisted reproductive technique in the dog. A case series study was performed to determine if TCI using frozen-thawed semen was a viable technique to offer in a general veterinary practice setting. Over a period exceeding 28 months, 137 Greyhound bitches were presented for assisted breeding. A single, timed insemination using a rigid cystoscope to aid in transcervical deposition of a frozen-thawed semen dose was given within 72 h after the behaviorally estrual bitch had a > 4 ng/mL serum progesterone concentration and estrus-categorized vaginal cytology. Litter size, pregnancy and whelping rate were collected; their association to semen center and stud dog were quantified. Of the 137 bitches, 117 were bred for one cycle and 20 were bred for two or more cycles, giving a total of 161 single, timed inseminations. Pregnancy rate was 89.4%, with 141 (87.5%) whelping. Litter size was 6.9+/-2.7 (mean+/-S.D.) pups. Semen center (P=0.84) and stud (P=0.79) had no effect on pregnancy. These results were quite favorable when compared to prior TCI studies, and are possibly due to the use of a single breed (i.e., Greyhound) with good fertility. This study supported the application of TCI, in Greyhounds, as a successful and viable service to offer in private practice. Additionally, these results have value in their use for benchmarking future breed-specific and TCI research. Serendipitously, the apparent fecundity results obtained in this observational study suggests a possible greater appreciation be given to breed composition and choice in assisted reproductive technique studies.

Technical - Economic Research for Passive Buildings

NASA Astrophysics Data System (ADS)

Miniotaite, Ruta

2017-10-01

A newly constructed passive house must save 80 % of heat resources; otherwise it is not a passive house. The heating energy demand of a passive building is less than 15 kWh/m2 per year. However, a passive house is something more than just an energy-saving house. This concept involves sustainable, high-quality, valuable, healthy and durable construction. Features of a passive house: high insulation of envelope components, high-quality windows, good tightness of the building, regenerative ventilation system and elimination of thermal bridges. The Energy Performance of Buildings Directive (EPBD) 61 requires all new public buildings to become near-zero energy buildings by 2019 and will be extended to all new buildings by 2021. This concept involves sustainable, high-quality, valuable, healthy and durable construction. Foundation, walls and roofs are the most essential elements of a house. The type of foundation for a private house is selected considering many factors. The article examines technological and structural solutions for passive buildings foundation, walls and roofs. The technical-economic comparison of the main structures of a passive house revealed that it is cheaper to install an adequately designed concrete slab foundation than to build strip or pile foundation and the floor separately. Timber stud walls are the cheapest wall option for a passive house and 45-51% cheaper compared to other options. The comparison of roofs and ceilings showed that insulation of the ceiling is 25% more efficient than insulation of the roof. The comparison of the main envelope elements efficiency by multiple-criteria evaluation methods showed that it is economically feasible to install concrete slab on ground foundation, stud walls with sheet cladding and a pitched roof with insulated ceiling.

Theoretical Loss and Gambling Intensity (Revisited): A Response to Braverman et al. (2013).

PubMed

Auer, Michael; Griffiths, Mark D

2015-09-01

In this paper, we provide a brief response to Braverman et al. (J Gambl Stud. doi: 10.1007/s10899-013-9428-z , 2013b) critique of our 'Theoretical Loss' metric as a measure of monetary gambling intensity (Auer and Griffiths in J Gambl Stud. doi: 10.1007/s10899-013-9376-7 , 2013a; Auer et al. in Gaming Law Rev Econ 16:269-273, 2012). We argue that 'gambling intensity' and 'gambling involvement' are essentially the same construct as descriptors of monetary gambling activity. Additionally, we acknowledge that playing duration (i.e., the amount of time—as opposed to money—actually spent gambling) is clearly another important indicator of gambling involvement-something that we have consistently noted in our previous studies including our empirical studies on gambling using behavioural tracking data. Braverman and colleagues claim that the concept of Theoretical Loss is nullified when statistical analysis focuses solely on one game type as the house edge is constant across all games. In fact, they state, the correlation between total amount wagered and Theoretical Loss is perfect. Unfortunately, this is incorrect. To disprove the claim made, we demonstrate that in sports betting (i.e., a single game type), the amount wagered does not reflect monetary gambling involvement using actual payout percentage data (based on 52,500 independent bets provided to us by an online European bookmaker). After reviewing the arguments presented by Braverman and colleagues, we are still of the view that when it comes to purely monetary measures of 'gambling intensity', the Theoretical Loss metric is a more robust and accurate measure than other financial proxy measures such as 'amount wagered' (i.e., bet size) as a measure of what players are prepared to financially risk while gambling.

Evaluation of the thermal and structural performance of straw bale construction

NASA Astrophysics Data System (ADS)

Beaudry, Kyle R.

This thesis is primarily divided into two distinct experimental programs evaluating: 1) the thermal performance and, 2) the structural performance of straw bale construction. The thermal performance chapter describes hot-box testing (based on ASTM C1363-11) of seven straw bale wall panels to obtain their apparent thermal conductivity values. All panels were constructed with stacked bales and cement-lime plaster skins on each side of the bales. Four panels were made with traditional, 2-string field bales of densities ranging from 89.5 kg/m3 - 131 kg/m3 and with the bales on-edge (fibres perpendicular to the heat flow). Three panels were made with manufactured high-density bales (291 kg/m3 - 372 kg/m3). The fibres of the manufactured bales were randomly oriented. The key conclusion of this work is that within the experimental error, there is no difference in the apparent thermal conductivity value for panels using normal density bales and manufactured high-density bales up to a density of 333 kg/m3. The structural performance chapter describes gravity and transverse load testing (based on ASTM E72-15) of non-plastered modular straw bale wall (DBW) panels to evaluate their strength capacity and failure modes. The out-of-plane flexural (OPF) tests exhibited a mean ultimate bending moment of 49.7 kNm. The axial compression (AC) tests exhibited a mean ultimate line load of 161.0 kN/m. The local flexural header beam (HP) tests exhibited an ultimate line load of 31.6 kN/m. The OPF and AC capacities of the DBW exceeded the capacities exhibited by a conventional 38 mm x 140 mm stud wall. However, the DBW's header beam strength and stiffness was inferior to conventional stud wall.

Fundamentals and advances in the development of remote welding fabrication systems

NASA Technical Reports Server (NTRS)

Agapakis, J. E.; Masubuchi, K.; Von Alt, C.

1986-01-01

Operational and man-machine issues for welding underwater, in outer space, and at other remote sites are investigated, and recent process developments are described. Probable remote welding missions are classified, and the essential characteristics of fundamental remote welding tasks are analyzed. Various possible operational modes for remote welding fabrication are identified, and appropriate roles for humans and machines are suggested. Human operator performance in remote welding fabrication tasks is discussed, and recent advances in the development of remote welding systems are described, including packaged welding systems, stud welding systems, remotely operated welding systems, and vision-aided remote robotic welding and autonomous welding systems.

Report and Recommendations on Study on the Application of Personnel Research to UMT Program (PR-4107)

DTIC Science & Technology

1947-08-29

personnel testing or m=as- urý &-vices," using existing Army personnel testa wherever possible 8?d projecting as a roonmrdtion any now poraonrol...it vi2J to oe~bLein coolmratiOn with the local highi schools,, twz condu-&ct 1=1al7 m-ach of tho namsary tos~tn*’-1 whch. now ahoorhe so wach of a...t%.’s sfuer the pro gra in undear way,, ’)a stud-ad .fuýr rav! sian., pa-rtcularly looking towaurd -:.-rup teAts to reicutdlld siteat. al tr u Is- a

Caps Seal Boltholes On Vacuum-System Flanges

NASA Technical Reports Server (NTRS)

Roman, Robert F.

1993-01-01

Sealing caps devised for boltholes on vacuum-system flanges. Used in place of leak-prone gaskets, and provide solid metal-to-metal interfaces. Each sealing cap contains square-cut circular groove in which O-ring placed. Mounted on studs protruding into access ports, providing positive seal around each bolthole. Each cap mates directly with surface of flange, in solid metal-to-metal fit, with O-ring completely captured in groove. Assembly immune to misalignment, leakage caused by vibration, and creeping distortion caused by weight of port. O-ring material chosen for resistance to high temperature; with appropriate choice of material, temperature raised to as much as 315 degrees C.

Local conditional entropy in measure for covers with respect to a fixed partition

NASA Astrophysics Data System (ADS)

Romagnoli, Pierre-Paul

2018-05-01

In this paper we introduce two measure theoretical notions of conditional entropy for finite measurable covers conditioned to a finite measurable partition and prove that they are equal. Using this we state a local variational principle with respect to the notion of conditional entropy defined by Misiurewicz (1976 Stud. Math. 55 176–200) for the case of open covers. This in particular extends the work done in Romagnoli (2003 Ergod. Theor. Dynam. Syst. 23 1601–10), Glasner and Weiss (2006 Handbook of Dynamical Systems vol 1B (Amsterdam: Elsevier)) and Huang et al (2006 Ergod. Theor. Dynam. Syst. 26 219–45).

The effects of low level microwaves on the fluidity of photoreceptor cell membrane.

PubMed

Pologea-Moraru, Roxana; Kovacs, Eugenia; Iliescu, Karina Roxana; Calota, Violeta; Sajin, Gheorghe

2002-05-15

Due to the extensive use of electromagnetic fields in everyday life, more information is required for the detection of mechanisms of interaction and the possible side effects of electromagnetic radiation on the structure and function of the organism. In this paper, we study the effects of low-power microwaves (2.45 GHz) on the membrane fluidity of rod photoreceptor cells. The retina is expected to be very sensitive to microwave irradiation due to the polar character of the photoreceptor cells [Biochim. Biophys. Acta 1273 (1995) 217] as well as to its high water content [Stud. Biophys. 81 (1981) 39].

The nonrelativistic limit of (central-extended) Poincaré group and some consequences for quantum actualization

NASA Astrophysics Data System (ADS)

Ardenghi, Juan S.; Castagnino, M.; Campoamor-Stursberg, R.

2009-10-01

The nonrelativistic limit of the centrally extended Poincaré group is considered and their consequences in the modal Hamiltonian interpretation of quantum mechanics are discussed [O. Lombardi and M. Castagnino, Stud. Hist. Philos. Mod. Phys 39, 380 (2008); J. Phys, Conf. Ser. 128, 012014 (2008)]. Through the assumption that in quantum field theory the Casimir operators of the Poincaré group actualize, the nonrelativistic limit of the latter group yields to the actualization of the Casimir operators of the Galilei group, which is in agreement with the actualization rule of previous versions of modal Hamiltonian interpretation [Ardenghi et al., Found. Phys. (submitted)].

Radiation Insulation

NASA Technical Reports Server (NTRS)

1993-01-01

An aluminized polymer film is a highly effective radiation barrier for both manned and unmanned spacecraft. Variations of this space-devised material are also used as an energy conservation technique for homes and offices. One commercial company, Tech 2000 (formerly Buckeye Radiant Barrier), markets 'Super R' Radiant Barrier, which finds its origins in the Apollo Mission programs. The material is placed between wall studs and exterior facing before siding or in new roof installation, between roof support and roof sheathing. Successful retrofit installations have included schools and shrink wrap ovens. The radiant barrier blocks 95 percent of radiant energy, thus retaining summer heat and blocking winter cold. Suppliers claim utility bill reductions of 20 percent or more.

A Numerical Simulation of the Flow Field and Heat Transfer in a Rectangular Passage with a Turbulence Promoter

DTIC Science & Technology

1988-06-01

Turbulence Augmentation 04 19 ABS. T (Continue on reverse di necessary and identify by block number) A n’-feriCal stud~y of the flow field and heat...urderpredicts the heat t ransfer re,,c as given I3- z. direct calculation Lusing Fcurier’s lawl. DD Form 1473, JUN 86 P~*’viowJ rdirionsa,e obsolete...SEWiPI’e CLASSIFiCV’i0N CIH, A UNCLASSIF D N -~ -~ ’ 4\\./~~ f. .% S ’ ’p ’ ’,S V % %~ TABLE OF CONTENTS SECTION PAGE T Introduction

Advances in Boar Semen Cryopreservation

PubMed Central

Rodriguez-Martinez, Heriberto; Wallgren, Margareta

2011-01-01

The present paper highlights aspects of the cryopreservation of boar semen, a species with particular large, fractionated ejaculates, and a cumbersome cryotechnology that had prevented its commercial application. With the dramatic increase of use of liquid pig semen for artificial breeding over the past decade, developments on cryopreservation alongside the routine use of stud boar semen for AI had been promoted. Recent advances in our laboratory, accommodating the best use of portions of the sperm-rich fraction of the ejaculate for cryopreservation of the sperm-peak portion (P1) and parallel use of the rest of the collected ejaculated spermatozoa, appears as a suitable commercial alternative. PMID:20871820

The Limits of the Czar’s Ukase: Drug Policy at the Local Level

DTIC Science & Technology

1990-06-01

to ends ()I or t set buidget priorIties. ’Struggles about which agency wvas c *g Il tic as’ .\\I)i (- IP 1 1i k M it p i. , i , tt I).: I cailictiihu...piall of 1 pl’)gl’iar titl’ed. "Moiitoling Ihe Future: A Contittilnig Stud% of the Ihi’stvles n)(] Valutes of Youth.- 10. Somieti Si,( hu l iistriI is ( M ...one drug mentio n-. in 1988. the is eragc n m her of mientions per case b\\ ER isas 1.63 and h% ME %%s.~ 2.431. showssing fle Pt valevnce of the

Construction Guide to Next-Generation High-Performance Walls in Climate Zones 3-5 - Part 2: 2x4 Walls

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kochkin, V.; Wiehagen, J.

2017-06-01

Part 2 of this Construction Guide to High-Performance Walls in Climate Zones 3-5 provides straightforward and cost-effective strategies to construct durable, energy-efficient walls. It addresses walls constructed with 2x4 wood frame studs, wood structural panel (WSP) sheathing as wall bracing and added backing for foam sheathing, a layer of rigid foam sheathing insulation up to 1.5 inches thick over the WSP, and a cladding system installed over the foam sheathing in low-rise residential buildings up to three stories high. Walls with 2x6 framing are addressed in Part 1 of the Guide.

Fixture for holding testing transducer

DOEpatents

Wagner, T.A.; Engel, H.P.

A fixture for mounting an ultrasonic transducer against the end of a threaded bolt or stud to test the same for flaws. A base means threadedly secured to the side of the bolt has a rotating ring thereon. A post rising up from the ring (parallel to the axis of the workpiece) pivotally mounts a variable length cross arm, on the inner end of which is mounted the transducer. A spring means acts between the cross arm and the base to apply the testing transducer against the workpiece at a constant pressure. The device maintains constant for successive tests the radial and circumferential positions of the testing transducer and its contact pressure against the end of the workpiece.

Fixture for holding testing transducer

DOEpatents

Wagner, Thomas A.; Engel, Herbert P.

1984-01-01

A fixture for mounting an ultrasonic transducer against the end of a threaded bolt or stud to test the same for flaws. A base means threadedly secured to the side of the bolt has a rotating ring thereon. A post rising up from the ring (parallel to the axis of the workpiece) pivotally mounts a variable length cross arm, on the inner end of which is mounted the transducer. A spring means acts between the cross arm and the base to apply the testing transducer against the workpiece at a constant pressure. The device maintains constant for successive tests the radial and circumferential positions of the testing transducer and its contact pressure against the end of the workpiece.

World's mountains over 5 miles above sea level as seen from the Apollo 7

NASA Technical Reports Server (NTRS)

1968-01-01

The world's dozen peaks which reach a height of greater than five miles above sea level are seen in this photograph from the Apollo 7 spacecraft at an altitude of 130 nautical miles. The 29,028 ft. high Mount Everest is at lower center. On the central horizon can be seen the 28,250 ft. high Mount Godwin-Austen (K-2) some 800 miles northwest of Mount Everest. In the lower right, Mount Kanchenjunga rises 28,208 ft. to separate Nepal from Sikkim. The snow line on the peaks was at 17,500 ft. In the upper right the lake-studded highlands of Tibet are visible.

Eradication of Infectious Bovine Rhinotracheitis Virus (Bovine Herpesvirus 1) from a Herd of Beef Cattle

PubMed Central

Bradley, J. A.

1985-01-01

Infectious bovine rhinotracheitis virus was eradicated from a 150 cow beef herd at the Animal Diseases Research Institute, Lethbridge, Alberta. Tests used to accomplish this included standard and modified serum-virus neutralization tests and an enzymelinked immunosorbent assay. These results and those of preliminary pilot studies in the herd and in a nonvaccinated, infectious bovine rhinotracheitis-infected 450 cow beef herd suggest that eradication of infectious bovine rhinotracheitis infection can be considered as a practical control alternative to vaccination, and that young animals in purebred herds could be monitored serologically and isolated, to enhance their eligibility for entry into artificial insemination studs or for export. PMID:17422544

Protaeolidiella atra Baba, 1955 versus Pleurolidia juliae Burn, 1966: One or two species?

NASA Astrophysics Data System (ADS)

Carmona, Leila; Pola, Marta; Gosliner, Terrence M.; Cervera, Juan Lucas

2015-06-01

Protaeolidiella atra Baba, 1955 and Pleurolidia juliae Burn, 1966 are two species traditionally regarded as the members of Aeolidiidae but recently attributed to Facelinidae. Because of their apparent similarities, Rudman (J Molluscan Stud 56:505-514, 1990) rendered P. juliae as a junior synonym of P. atra. In this paper, we conducted a review of both species and completed their descriptions with new data regarding the anatomy of the reproductive system . P. atra and P. juliae have differences in their colouration, number of cerata and characteristics of their reproductive system. Based on these differences, we conclude that these species are not conspecific and should be regarded as distinct taxa.

Stiffening of short small-size circular composite steel–concrete columns with shear connectors

PubMed Central

Younes, Sherif M.; Ramadan, Hazem M.; Mourad, Sherif A.

2015-01-01

An experimental program was conducted to investigate the effect of shear connectors’ distribution and method of load application on load–displacement relationship and behavior of thin-walled short concrete-filled steel tube (CFT) columns when subjected to axial load. The study focused on the compressive strength of the CFT columns and the efficiency of the shear stud in distribution of the load between the concrete core and steel tube. The study showed that the use of shear connectors enhanced slightly the axial capacity of CFT columns. It is also shown that shear connectors have a great effect on load distribution between the concrete and steel tubes. PMID:27222757

Construction Guide to Next-Generation High-Performance Walls in Climate Zones 3-5 - Part 2: 2x4 Walls

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kochkin, V.; Wiehagen, J.

Part 2 of this Construction Guide to High-Performance Walls in Climate Zones 3-5 provides straightforward and cost-effective strategies to construct durable, energy-efficient walls. It addresses walls constructed with 2x4 wood frame studs, wood structural panel (WSP) sheathing as wall bracing and added backing for foam sheathing, a layer of rigid foam sheathing insulation up to 1.5 inches thick over the WSP, and a cladding system installed over the foam sheathing in low-rise residential buildings up to three stories high. Walls with 2x6 framing are addressed in Part 1 of the Guide.

The Penrose dodecahedron revisited

NASA Astrophysics Data System (ADS)

Massad, Jordan E.; Aravind, P. K.

1999-07-01

This paper gives an elementary account of the "Penrose dodecahedron," a set of 40 states of a spin-3/2 particle used by Zimba and Penrose [Stud. Hist. Phil. Sci. 24, 697-720 (1993)] to give a proof of Bell's nonlocality theorem. The Penrose rays are constructed here from the rotation operator of a spin-3/2 particle and the geometry of a dodecahedron, and their orthogonality properties are derived and illustrated from a couple of different viewpoints. After recalling how the proof of Bell's theorem can be reduced to a coloring problem on the Penrose rays, a "proof-tree" argument is used to establish the noncolorability of the Penrose rays and hence prove Bell's theorem.

Advanced thermionic energy conversion

NASA Technical Reports Server (NTRS)

1979-01-01

Developments towards space and terrestrial applications of thermionic energy conversion are presented. Significant accomplishments for the three month period include: (1) devised a blade-type distributed lead design with many advantages compared to the stud-type distributed lead; (2) completed design of Marchuk tube test apparatus; (3) concluded, based on current understanding, that residual hydrogen should not contribute to a negative space charge barrier at the collector; (4) modified THX design program to include series-coupled designs as well as inductively-coupled designs; (5) initiated work on the heat transfer technology, THX test module, output power transfer system, heat transfer system, and conceptual plant design tasks; and (6) reached 2200 hours of operation in JPL-5 cylindrical converter envelope test.

Undergraduate Experiences of Division I Athlete Science, Technology, Engineering, and Mathematics (STEM) Graduates

NASA Astrophysics Data System (ADS)

Comeaux, Eddie; Bachman, Tina; Burton, Rena M.; Aliyeva, Aida

2017-02-01

Employing the conceptual model developed by Comeaux and Harrison (Coll Stud Aff J 30(1):75-87, 2011), this study explored the undergraduate experience of Division I athlete STEM graduates. Data collection involved 17 in-depth interviews with former athletes at two research-intensive, public institutions. Results revealed that pre-college characteristics, involvement in purposeful STEM-related activities, and sport participation, as well as academic support and guidance within athletic departments, play important roles in shaping the experiences of athletes who earn STEM degrees. Implications for student affairs professionals, faculty, and others who frequently interact with college athletes and are committed to creating more equitable educational environments are discussed.

A short review on thermosonic flip chip bonding

NASA Astrophysics Data System (ADS)

Suppiah, Sarveshvaran; Ong, Nestor Rubio; Sauli, Zaliman; Sarukunaselan, Karunavani; Alcain, Jesselyn Barro; Shahimin, Mukhzeer Mohamad; Retnasamy, Vithyacharan

2017-09-01

This review is to study the evolution and key findings, critical technical challenges, solutions and bonding equipment of thermosonic flip chip bonding. Based on the review done, it was found that ultrasonic power, bonding time and force are the three main critical parameters need to be optimized in order to achieve sound and reliable bonding between the die and substrate. A close monitoring of the ultrasonic power helped to prevent over bonding phenomena on flexible substrate. Gold stud bumping is commonly used in thermosonic bonding compared to solder due to its better reliability obtained in the LED and optoelectronic packages. The review comprised short details on the available thermosonic bonding equipment in the semiconductor industry as well.

Protective interior wall and attach8ing means for a fusion reactor vacuum vessel

DOEpatents

Phelps, Richard D.; Upham, Gerald A.; Anderson, Paul M.

1988-01-01

An array of connected plates mounted on the inside wall of the vacuum vessel of a magnetic confinement reactor in order to provide a protective surface for energy deposition inside the vessel. All fasteners are concealed and protected beneath the plates, while the plates themselves share common mounting points. The entire array is installed with torqued nuts on threaded studs; provision also exists for thermal expansion by mounting each plate with two of its four mounts captured in an oversize grooved spool. A spool-washer mounting hardware allows one edge of a protective plate to be torqued while the other side remains loose, by simply inverting the spool-washer hardware.

DOE ZERH Case Study: BPC Green Builders, Taft School, Watertown, CT

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

Case study of a DOE 2015 Housing Innovation Award winning custom home in the cold climate that got a HERS 33 without PV or HERS -14 with PV, with 8.5” double 2x4 walls with 8.5” (R-32) blown cellulose plus R-6 rigid foam, basement with 3” ccsf on interior plus 2x4 stud walls with R-13 blown cellulose, with R-20 around slab, R-38 under slab; a vented attic with R-100 blown cellulose; a central heat pump; HRV; heat pump water heater; 100% LED; and Passive House Institute U.S.+, LEED platinum, and Living Building Challenge certifications.

Full-Scale Experimental Investigation to Quantify Building Component Ignition Vulnerability from Mulch Beds Attacked by Firebrand Showers.

PubMed

Manzello, Samuel L; Suzuki, Sayaka; Nii, Daisaku

2017-03-01

Structure ignition by wind-driven firebrand showers is an important fire spread mechanism in large outdoor fires. Experiments were conducted with three common mulch types (shredded hardwood mulch, Japanese Cypress wood chips, and pine bark nuggets) placed adjacent to realistic-scale reentrant corners. In the first series of experiments, mulch beds were placed adjacent to a re-entrant corner constructed with wood studs and lined with oriented strand board (OSB) as the sheathing. The premise behind conducting experiments with no siding treatments applied was predicated on the notion that bare OSB mulch contact would be a worst-case scenario, and therefore, a wall assembly in the most vulnerable state to mulch ignition. In the second series of experiments, vinyl siding was applied to the re-entrant corner assemblies (wood studs/OSB/moisture barrier/vinyl siding), and the influence of vertical separation distance (102 mm or 203 mm) on wall ignition from adjacent mulch beds was determined. The vertical separation distance was maintained by applying gypsum board to the base of the re-entrant corner. The siding itself did not influence the ignition process for the mulch beds, as the mulch beds were the first to ignite from the firebrand showers. In all experiments, it was observed that firebrands produced smoldering ignition in the mulch beds, this transitioned to flaming ignition, and the re-entrant corner assembly was exposed to the flaming mulch beds. With no siding treatments applied, the flaming mulch beds ignited the re-entrant corner, and ignition was observed to propagate to the back side of re-entrant corner assembly under all wind speeds (6 m/s to 8 m/s). With respect to the re-entrant corners fitted with vinyl siding, the mulch type, vertical separation distance, and wind speed were important parameters as to whether flaming ignition was observed to propagate to the back-side of a reentrant corner assembly. Mulches clearly pose an ignition hazard to structures in large outdoor fires.

Cardiorespiratory responses of air filtration: A randomized crossover intervention trial in seniors living in Beijing: Beijing Indoor Air Purifier StudY, BIAPSY.

PubMed

Shao, Danqing; Du, Yipeng; Liu, Shuo; Brunekreef, Bert; Meliefste, Kees; Zhao, Qian; Chen, Jie; Song, Xiaoming; Wang, Meng; Wang, Juan; Xu, Hongbing; Wu, Rongshan; Wang, Tong; Feng, Baihuan; Lung, Candice Shih-Chun; Wang, Xian; He, Bei; Huang, Wei

2017-12-15

In this Beijing Indoor Air Purifier StudY (BIAPSY), we conducted a randomized crossover intervention trial in a panel of 35 non-smoking senior participants with free-living, with and without chronic obstructive pulmonary disease (COPD). Portable air filtration units were randomly allocated to active-(filter in) for 2weeks and sham-mode (filter out) for 2weeks in the households. We examined the differences in indoor air pollutant concentrations in 20 study homes and a suite of cardio-respiratory biomarker levels in study participants between filtration modes, with and without adjustment for potential confounders. Following active filtration, we observed significant reductions from 60±45 to 24±15μg/m 3 in ten-day averages of indoor PM 2.5 and reductions from 3.87±1.65 to 1.81±1.19m -1 .10 -5 in ten-day averages of indoor BC, compared to sham-mode filtration. The major components of indoor PM 2.5 , including water soluble organics, NO 3 - , SO 4 2- , Zn 2+ , Pb 2+ and K + , were also reduced significantly by 42% to 63%. However, following active filtration, we only observed significant reductions on systemic inflammation measured as of IL-8 at 58.59% (95% CI: -76.31, -27.64) in the total group of participants and 70.04% (95% CI: -83.05, -47.05) in the subset of COPD patients, with adjustments. We were not able to detect improvements on lung function, blood pressure, and heart rate variability, following short-term intervention of two-week active air filtration. In conclusion, our results showed that indoor air filtration produced clear improvement on indoor air quality, but no demonstrable changes in the cardio-respiratory outcomes of study interest observed in the seniors living with real-world air pollution exposures. Copyright © 2017 Elsevier B.V. All rights reserved.

The development of hoof balance and landing preference in the post-natal period.

PubMed

Gorissen, B M C; Serra Bragança, F M; Wolschrijn, C F; Back, W; van Weeren, P R

2018-04-20

Foals can follow the herd within hours of birth, but it has been shown that kinetic gait parameters and static balance still have to mature. However, development of dynamic balance has not been investigated. To objectively quantify landing and pressure pattern dynamics under the hoof during the first half year of life. Prospective, cohort study performed at a single stud farm. Pressure plate measurements at walk and trot from ten Dutch warmblood foals during the first 24 weeks of life were used to quantify toe-heel and medial-lateral hoof balance asymmetry indexes and to determine preferred landing strategy. Concurrently, radiographs of the tarsocrural and femoropatellar joints were taken at 4-6 weeks and after 6 months to check for osteochondrosis. A linear mixed model was used to determine the effects of time point, limb pair (front/hind), side (left/right) and osteochondrosis status of every foal. At 25% of stance duration at walk, front limbs were more loaded in the heel region in weeks 6-20 (P≤0.04), the medial-lateral balance was more to the lateral side from week 6 onwards at both walk and trot (P≤0.04). Landing preference gradually changed in the same directions. Variability in pressure distribution decreased over time. (Subclinical) osteochondrosis did not influence any of the measured parameters. This study is limited by the relatively small sample size only containing one breed from a single stud farm. Dynamic hoof balance in new-born foals is more variable and less oriented towards the lateral side of the hoof and to the heel than in mature horses. This pattern changes gradually during the first weeks of life. Knowledge of this process is essential for the clinician when considering interventions in this area in early life. © 2018 The Authors. Equine Veterinary Journal published by John Wiley & Sons Ltd on behalf of EVJ Ltd.

Seasonal variation in coat characteristics, tick loads, cortisol levels, some physiological parameters and temperature humidity index on Nguni cows raised in low- and high-input farms

NASA Astrophysics Data System (ADS)

Katiyatiya, C. L. F.; Muchenje, V.; Mushunje, A.

2015-06-01

Seasonal variations in hair length, tick loads, cortisol levels, haematological parameters (HP) and temperature humidity index (THI) in Nguni cows of different colours raised in two low-input farms, and a commercial stud was determined. The sites were chosen based on their production systems, climatic characteristics and geographical locations. Zazulwana and Komga are low-input, humid-coastal areas, while Honeydale is a high-input, dry-inland Nguni stud farm. A total of 103 cows, grouped according to parity, location and coat colour, were used in the study. The effects of location, coat colour, hair length and season were used to determine tick loads on different body parts, cortisol levels and HP in blood from Nguni cows. Highest tick loads were recorded under the tail and the lowest on the head of each of the animals ( P < 0.05). Zazulwana cows recorded the highest tick loads under the tails of all the cows used in the study from the three farms ( P < 0.05). High tick loads were recorded for cows with long hairs. Hair lengths were longest during the winter season in the coastal areas of Zazulwana and Honeydale ( P < 0.05). White and brown-white patched cows had significantly longer ( P < 0.05) hair strands than those having a combination of red, black and white colour. Cortisol and THI were significantly lower ( P < 0.05) in summer season. Red blood cells, haematoglobin, haematocrit, mean cell volumes, white blood cells, neutrophils, lymphocytes, eosinophils and basophils were significantly different ( P < 0.05) as some associated with age across all seasons and correlated to THI. It was concluded that the location, coat colour and season had effects on hair length, cortisol levels, THI, HP and tick loads on different body parts and heat stress in Nguni cows.

Design of SC walls and slabs for impulsive loading

DOE Office of Scientific and Technical Information (OSTI.GOV)

Varma, Amit H.

2015-11-11

Reinforced concrete (RC) structures have historically been the preferred choice for blast resistant structures because of their mass and the ductility provided by steel reinforcement. Steel-plate composite (SC) walls are a viable alternative to RC for protecting the infrastructure against explosive threats. SC structures consist of two steel faceplates with a plain concrete core between them. The steel faceplates are anchored to the concrete using stud anchors and connected to each other using tie bars. SC structures provide mass from the concrete infill and ductility from the continuous external steel faceplates. This dissertation presents findings and recommendations from experimental andmore » analytical investigations of the performance of SC walls subjected to far-field blast loads.« less

World's mountains over 5 miles above sea level as seen from the Apollo 7

NASA Image and Video Library

1968-10-15

AS7-07-1748 (15 Oct. 1968) --- The world's dozen peaks which reach a height of greater than five miles above sea level are seen in this photograph from the Apollo 7 spacecraft at an altitude of approximately 130 nautical miles. The 29,028 ft. high Mount Everest is at lower center. On the central horizon can be seen the 28,250 ft. high Mount Godwin-Austen (K-2) some 800 miles northwest of Mount Everest. In the lower right, Mount Kanchenjunga rises 28,208 ft. to separate Nepal from Sikkim. The snow line on the peaks was at 17,500 ft. In the upper right the lake-studded highlands of Tibet are visible.

Measurement and analysis of force-time outputs of pyrotechnic nuts

NASA Technical Reports Server (NTRS)

Neubert, V. H.

1973-01-01

The dynamic loadings produced by two standard pyrotechnic nuts were compared with loadings produced by four recently developed low-shock nuts. The nuts were manufactured by separate contractors. Each nut was given a number designation, the number having no special significance. The results show that the use of the Hopkinson bar to measure force-time outputs of the nuts at stud and housing sides aided greatly in understanding the events occurring in the nuts. Acceleration data appear to be dependable, for the most part, but of more limited value. The low-shock designs show considerable improvement over the standard designs above 4,000 Hz when the results are plotted in shock spectrum form. They involve some penalties with regard to weight and cost.

[Two cases of tetany in the horse (author's transl)].

PubMed

Meijer, P

1982-05-01

Two cases of tetany in the horse are reported. The two patients were thoroughbreds. One was eight and the other thirteen years old. The mares were in heat and were brought to the service (stud) station to be mated. Both patients were nursing a foal. One was a four-week-old foal and the other was seven weeks old. The calcium level of the serum had dropped in the two patients, to 4.0 mg and 5.4 per ml. respectively. The magnesium level was 1.0 mg and 1.9 mg per 100 ml. respectively. The animals responded satisfactorily to intravenous infusion of calcium borogluconate and magnesium chloride. One of the mares was also give 10 1. of physiological saline a few times.

Properties of various plasma surface treatments for low-temperature Au–Au bonding

NASA Astrophysics Data System (ADS)

Yamamoto, Michitaka; Higurashi, Eiji; Suga, Tadatomo; Sawada, Renshi; Itoh, Toshihiro

2018-04-01

Atmospheric-pressure (AP) plasma treatment using three different types of gases (an argon-hydrogen mixed gas, an argon-oxygen mixed gas, and a nitrogen gas) and low-pressure (LP) plasma treatment using an argon gas were compared for Au–Au bonding with thin films and stud bumps at low temperature (25 or 150 °C) in ambient air. The argon-hydrogen gas mixture AP plasma treatment and argon LP plasma treatment were found to distinctly increase the shear bond strength for both samples at both temperatures. From X-ray photoelectron spectroscopy (XPS) analysis, the removal of organic contaminants on Au surfaces without the formation of hydroxyl groups and gold oxide is considered effective in increasing the Au–Au bonding strength at low temperature.

Discrete maximal regularity of time-stepping schemes for fractional evolution equations.

PubMed

Jin, Bangti; Li, Buyang; Zhou, Zhi

2018-01-01

In this work, we establish the maximal [Formula: see text]-regularity for several time stepping schemes for a fractional evolution model, which involves a fractional derivative of order [Formula: see text], [Formula: see text], in time. These schemes include convolution quadratures generated by backward Euler method and second-order backward difference formula, the L1 scheme, explicit Euler method and a fractional variant of the Crank-Nicolson method. The main tools for the analysis include operator-valued Fourier multiplier theorem due to Weis (Math Ann 319:735-758, 2001. doi:10.1007/PL00004457) and its discrete analogue due to Blunck (Stud Math 146:157-176, 2001. doi:10.4064/sm146-2-3). These results generalize the corresponding results for parabolic problems.

Lego bricks and the octet rule: Molecular models for biochemical pathways with plastic, interlocking toy bricks.

PubMed

Lin, Henry J; Lehoang, Jennifer; Kwan, Isabel; Baghaee, Anita; Prasad, Priya; Ha-Chen, Stephanie J; Moss, Tanesha; Woods, Jeremy D

2018-01-01

The 8 studs on a 2 × 4 Lego brick conveniently represent the outer shell of electrons for carbon, nitrogen, and oxygen atoms. We used Lego bricks to model these atoms, which are then joined together to form molecules by following the Lewis octet rule. A variety of small biological molecules can be modeled in this way, such as most amino acids, fatty acids, glucose, and various intermediate metabolites. Model building with these familiar toys can be a helpful, hands-on exercise for learning-or re-learning-biochemical pathways. © 2017 by The International Union of Biochemistry and Molecular Biology, 46(1):54-57, 2018. © 2017 The International Union of Biochemistry and Molecular Biology.

Hand injury with a nail gun: a case report with literature review.

PubMed

Boya, Hakan; Uzun, Belkan

2015-01-01

The nail gun was introduced in the late 1950s to increase the ease of driving nails, studs, bolts, or staples into various hard surfaces. The nail gun is a potentially dangerous device that is still commonly used in the construction industry. Since its introduction, an increasing number of studies have reported injuries associated with nail guns. Nail gun-related injuries-such as to the head, neck, and chest-can be devastating, and in some cases, even fatal. Extremity injuries, notably in the hand, can cause loss of function, missed work, and long-term health effects. This case report describes a nail-gun injury of the hand along with a discussion of the unique features of and treatment strategies for nail gun injuries.

[Nickel contact dermatitis. A ring signal in actual pathology].

PubMed

Cherciu, Mirela; Zbranca, Anca

2004-01-01

Contact dermatitis produced by nickel is extremely common in women by earrings or other items of jewelry which contain nickel. Areas of involvement are under rings, bracelets, watches, spectacle frames, coins in pockets, jeans studs and other sites of direct contact with the metal. The frequency of nickel dermatitis is increasing in the male population and this may be due of body-piercing or professional contact in the field of metallic constructions. The treatment is difficult because of the presence of nickel in so many substances, things or even food. The management of contact dermatitis include the reduction or elimination of the allergen, the use of topical or systemic steroids, oral desensitisation and use of nickel in selected cases.

A study of the optimal transition temperatue of PCM (Phase Change Material) wallboard for solar energy storage

NASA Astrophysics Data System (ADS)

Drake, J. B.

1987-09-01

The performance of wallboard impregnated with phase change material (PCM) is considered. An ideal setting is assumed and several measures of performance discussed. With a definition of optimal performance given, the performance with respect to variation of transition temperature is studied. Results are based on computer simulations of PCM wallboard with a standard stud wall construction. The diurnal heat capacity was found to be to be overly sensitive to numerical errors for use in PCM applications. The other measures of performance, diurnal effectiveness, net collected to storage ratio, and absolute discharge flux, all indicate similar trends. It is shown that the optimal transition temperature of the PCM is strongly influenced by the amount of solar flux absorbed.

Morphology of the infective larval stage of the equid parasite Habronema muscae (Spirurida: Habronematidae), from houseflies (Musca domestica).

PubMed

Buzzell, Gerald R; Tariq, Saeed; Traversa, Donato; Schuster, Rolf

2011-03-01

The infective larva of the spirurid nematode Habronema muscae, a parasite of houseflies, was measured and specimens fixed in Karnovsky's fluid were examined by scanning electron microscopy. The oral opening contains six teeth and is surrounded by large bilobed dorsal and ventral lips and smaller lateral lips. A pair of amphids lie behind the lateral lips. There are two rows of four cephalic papillae. The body is deeply ridged, both transversely and longitudinally. The caudal end of the worm is studded by small papillae. The position of the anal opening is somewhat ambiguous. These larval morphological features are discussed, as well as the changes which must have occurred in the metamorphosis of the infective larva to the adult in the stomach of horses.

Navigating "thorny" issues

NASA Astrophysics Data System (ADS)

Hutchinson, Kashema; Gilbert, Aderinsola; Malyukova, Anna

2016-09-01

In their article Mindfulness and discussing ` thorny' issues in the classroom Konstantinos Alexakos et al. (Cult Stud Sci Educ, 2016. doi: 10.1007/s11422-015-9718-0) describe "thorny" issues as "difficult topics to discuss because they are more personal to some perhaps even cause pain and violence." As women from different backgrounds, we engage in a metalogue, which expands on our thoughts and emotions the thorny issues evoked. Our discussion is grounded in theoretical frameworks of mindfulness, wellness, and safe space for learning. We also reflect on our experiences of facing some of the thorny issues in our academic and personal lives. Having trust and respect for one another and being aware of thorny issues allows for a meaningful conversation about the complexity and nuances involved in discussing difficult topics in a classroom setting.

Effect of Hydrogenase and Mixed Sulfate-Reducing Bacterial Populations on the Corrosion of Steel

PubMed Central

Bryant, Richard D.; Jansen, Wayne; Boivin, Joe; Laishley, Edward J.; Costerton, J. William

1991-01-01

The importance of hydrogenase activity to corrosion of steel was assessed by using mixed populations of sulfate-reducing bacteria isolated from corroded and noncorroded oil pipelines. Biofilms which developed on the steel studs contained detectable numbers of sulfate-reducing bacteria (104 increasing to 107/0.5 cm2). However, the biofilm with active hydrogenase activity (i.e., corrosion pipeline organisms), as measured by a semiquantitative commercial kit, was associated with a significantly higher corrosion rate (7.79 mm/year) relative to noncorrosive biofilm (0.48 mm/year) with 105 sulfate-reducing bacteria per 0.5 cm2 but no measurable hydrogenase activity. The importance of hydrogenase and the microbial sulfate-reducing bacterial population making up the biofilm are discussed relative to biocorrosion. Images PMID:16348560

Deriving amplitude equations for weakly-nonlinear oscillators and their generalizations

NASA Astrophysics Data System (ADS)

O'Malley, Robert E., Jr.; Williams, David B.

2006-06-01

Results by physicists on renormalization group techniques have recently sparked interest in the singular perturbations community of applied mathematicians. The survey paper, [Phys. Rev. E 54(1) (1996) 376-394], by Chen et al. demonstrated that many problems which applied mathematicians solve using disparate methods can be solved using a single approach. Analysis of that renormalization group method by Mudavanhu and O'Malley [Stud. Appl. Math. 107(1) (2001) 63-79; SIAM J. Appl. Math. 63(2) (2002) 373-397], among others, indicates that the technique can be streamlined. This paper carries that analysis several steps further to present an amplitude equation technique which is both well adapted for use with a computer algebra system and easy to relate to the classical methods of averaging and multiple scales.