Gram-Scale Synthesized Pd2Co-Supported PtMonolayers Electrocatalysts for Oxygen Reduction Reaction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, W.P.; Sasaki, K.; Su, D.

2010-04-21

Gram-scale synthesis of Pt{sub ML} electrocatalysts with a well-defined core-shell structure has been carried out using method involving galvanic displacement of an underpotential deposition Cu layer. The Pt shell thickness can be controlled by stepwise deposition. The Pt{at}Pd{sub 2}Co/C nanoparticles were characterized by X-ray powder diffraction, aberration-corrected scanning transmission electron microscopy, high-resolution energy-loss spectrometry, and in situ X-ray absorption spectroscopy. A complete Pt shell of 0.6 nm on a Pd{sub 2}Co core has been confirmed. The Pt{at}Pd{sub 2}Co/C core-shell electrocatalysts showed a very high activity for the oxygen reduction reaction; the Pt mass and specific activity were 0.72 A mg{supmore » -1}{sub Pt} and 0.5 mA cm{sup -2}, respectively (3.5 and 2.5 times higher than the corresponding values for commercial Pt catalysts), at 0.9 V in 0.1 M HClO{sub 4} at room temperature. In an accelerated potential cycling test, a loss in active surface area and a decrease in catalytic activity for gram-scale-synthesized Pt{sub ML} catalysts were also determined.« less

Influence of foot pain on walking ability of diabetic patients.

PubMed

Novak, Primoz; Burger, Helena; Marincek, Crt; Meh, Duska

2004-11-01

To assess foot pain and its correlation with walking ability in diabetic patients. Two groups of type 2 diabetic patients (30 with symptomatic neuropathy and 30 without symptomatic neuropathy) and 30 healthy volunteers were studied. Pain was assessed by the pain sub-scale of the Foot Function Index. Internal consistency for the pain sub-scale was tested. Walking ability was assessed by the 6-minute walking test. The pain was worse in diabetic patients, the pain sub-scale scores differed between the groups (p < 0.05). High internal consistency was found for the pain sub-scale of the Foot Function Index. Results of the 6-minute walking test differed among the 3 groups: healthy volunteers performed best, and diabetic patients with symptomatic neuropathy worst (p < 0.001). Foot pain correlated moderately with the result of walking test (r = -0.449, p < 0.001). The pain sub-scale of the Foot Function Index is suitable for the assessment of pain in diabetic patients. Patients with severe foot pain have more difficulties when walking long distances than patients with less severe or without any pain.

Subscale Validation of the Subsurface Active Filtration of Exhaust (SAFE) Approach to the NTP Ground Testing

NASA Technical Reports Server (NTRS)

Marshall, William M.; Borowski, Stanley K.; Bulman, Mel; Joyner, Russell; Martin, Charles R.

2015-01-01

Nuclear thermal propulsion (NTP) has been recognized as an enabling technology for missions to Mars and beyond. However, one of the key challenges of developing a nuclear thermal rocket is conducting verification and development tests on the ground. A number of ground test options are presented, with the Sub-surface Active Filtration of Exhaust (SAFE) method identified as a preferred path forward for the NTP program. The SAFE concept utilizes the natural soil characteristics present at the Nevada National Security Site to provide a natural filter for nuclear rocket exhaust during ground testing. A validation method of the SAFE concept is presented, utilizing a non-nuclear sub-scale hydrogen/oxygen rocket seeded with detectible radioisotopes. Additionally, some alternative ground test concepts, based upon the SAFE concept, are presented. Finally, an overview of the ongoing discussions of developing a ground test campaign are presented.

Numerical Modeling of Propellant Boil-Off in a Cryogenic Storage Tank

NASA Technical Reports Server (NTRS)

Majumdar, A. K.; Steadman, T. E.; Maroney, J. L.; Sass, J. P.; Fesmire, J. E.

2007-01-01

A numerical model to predict boil-off of stored propellant in large spherical cryogenic tanks has been developed. Accurate prediction of tank boil-off rates for different thermal insulation systems was the goal of this collaboration effort. The Generalized Fluid System Simulation Program, integrating flow analysis and conjugate heat transfer for solving complex fluid system problems, was used to create the model. Calculation of tank boil-off rate requires simultaneous simulation of heat transfer processes among liquid propellant, vapor ullage space, and tank structure. The reference tank for the boil-off model was the 850,000 gallon liquid hydrogen tank at Launch Complex 39B (LC- 39B) at Kennedy Space Center, which is under study for future infrastructure improvements to support the Constellation program. The methodology employed in the numerical model was validated using a sub-scale model and tank. Experimental test data from a 1/15th scale version of the LC-39B tank using both liquid hydrogen and liquid nitrogen were used to anchor the analytical predictions of the sub-scale model. Favorable correlations between sub-scale model and experimental test data have provided confidence in full-scale tank boil-off predictions. These methods are now being used in the preliminary design for other cases including future launch vehicles

Neural Network Prediction of New Aircraft Design Coefficients

NASA Technical Reports Server (NTRS)

Norgaard, Magnus; Jorgensen, Charles C.; Ross, James C.

1997-01-01

This paper discusses a neural network tool for more effective aircraft design evaluations during wind tunnel tests. Using a hybrid neural network optimization method, we have produced fast and reliable predictions of aerodynamical coefficients, found optimal flap settings, and flap schedules. For validation, the tool was tested on a 55% scale model of the USAF/NASA Subsonic High Alpha Research Concept aircraft (SHARC). Four different networks were trained to predict coefficients of lift, drag, moment of inertia, and lift drag ratio (C(sub L), C(sub D), C(sub M), and L/D) from angle of attack and flap settings. The latter network was then used to determine an overall optimal flap setting and for finding optimal flap schedules.

Towards improved parameterization of a macroscale hydrologic model in a discontinuous permafrost boreal forest ecosystem

DOE PAGES

Endalamaw, Abraham; Bolton, W. Robert; Young-Robertson, Jessica M.; ...

2017-09-14

Modeling hydrological processes in the Alaskan sub-arctic is challenging because of the extreme spatial heterogeneity in soil properties and vegetation communities. Nevertheless, modeling and predicting hydrological processes is critical in this region due to its vulnerability to the effects of climate change. Coarse-spatial-resolution datasets used in land surface modeling pose a new challenge in simulating the spatially distributed and basin-integrated processes since these datasets do not adequately represent the small-scale hydrological, thermal, and ecological heterogeneity. The goal of this study is to improve the prediction capacity of mesoscale to large-scale hydrological models by introducing a small-scale parameterization scheme, which bettermore » represents the spatial heterogeneity of soil properties and vegetation cover in the Alaskan sub-arctic. The small-scale parameterization schemes are derived from observations and a sub-grid parameterization method in the two contrasting sub-basins of the Caribou Poker Creek Research Watershed (CPCRW) in Interior Alaska: one nearly permafrost-free (LowP) sub-basin and one permafrost-dominated (HighP) sub-basin. The sub-grid parameterization method used in the small-scale parameterization scheme is derived from the watershed topography. We found that observed soil thermal and hydraulic properties – including the distribution of permafrost and vegetation cover heterogeneity – are better represented in the sub-grid parameterization method than the coarse-resolution datasets. Parameters derived from the coarse-resolution datasets and from the sub-grid parameterization method are implemented into the variable infiltration capacity (VIC) mesoscale hydrological model to simulate runoff, evapotranspiration (ET), and soil moisture in the two sub-basins of the CPCRW. Simulated hydrographs based on the small-scale parameterization capture most of the peak and low flows, with similar accuracy in both sub-basins, compared to simulated hydrographs based on the coarse-resolution datasets. On average, the small-scale parameterization scheme improves the total runoff simulation by up to 50 % in the LowP sub-basin and by up to 10 % in the HighP sub-basin from the large-scale parameterization. This study shows that the proposed sub-grid parameterization method can be used to improve the performance of mesoscale hydrological models in the Alaskan sub-arctic watersheds.« less

Towards improved parameterization of a macroscale hydrologic model in a discontinuous permafrost boreal forest ecosystem

DOE Office of Scientific and Technical Information (OSTI.GOV)

Endalamaw, Abraham; Bolton, W. Robert; Young-Robertson, Jessica M.

Modeling hydrological processes in the Alaskan sub-arctic is challenging because of the extreme spatial heterogeneity in soil properties and vegetation communities. Nevertheless, modeling and predicting hydrological processes is critical in this region due to its vulnerability to the effects of climate change. Coarse-spatial-resolution datasets used in land surface modeling pose a new challenge in simulating the spatially distributed and basin-integrated processes since these datasets do not adequately represent the small-scale hydrological, thermal, and ecological heterogeneity. The goal of this study is to improve the prediction capacity of mesoscale to large-scale hydrological models by introducing a small-scale parameterization scheme, which bettermore » represents the spatial heterogeneity of soil properties and vegetation cover in the Alaskan sub-arctic. The small-scale parameterization schemes are derived from observations and a sub-grid parameterization method in the two contrasting sub-basins of the Caribou Poker Creek Research Watershed (CPCRW) in Interior Alaska: one nearly permafrost-free (LowP) sub-basin and one permafrost-dominated (HighP) sub-basin. The sub-grid parameterization method used in the small-scale parameterization scheme is derived from the watershed topography. We found that observed soil thermal and hydraulic properties – including the distribution of permafrost and vegetation cover heterogeneity – are better represented in the sub-grid parameterization method than the coarse-resolution datasets. Parameters derived from the coarse-resolution datasets and from the sub-grid parameterization method are implemented into the variable infiltration capacity (VIC) mesoscale hydrological model to simulate runoff, evapotranspiration (ET), and soil moisture in the two sub-basins of the CPCRW. Simulated hydrographs based on the small-scale parameterization capture most of the peak and low flows, with similar accuracy in both sub-basins, compared to simulated hydrographs based on the coarse-resolution datasets. On average, the small-scale parameterization scheme improves the total runoff simulation by up to 50 % in the LowP sub-basin and by up to 10 % in the HighP sub-basin from the large-scale parameterization. This study shows that the proposed sub-grid parameterization method can be used to improve the performance of mesoscale hydrological models in the Alaskan sub-arctic watersheds.« less

Evaluation of Icing Scaling on Swept NACA 0012 Airfoil Models

NASA Technical Reports Server (NTRS)

Tsao, Jen-Ching; Lee, Sam

2012-01-01

Icing scaling tests in the NASA Glenn Icing Research Tunnel (IRT) were performed on swept wing models using existing recommended scaling methods that were originally developed for straight wing. Some needed modifications on the stagnation-point local collection efficiency (i.e., beta(sub 0) calculation and the corresponding convective heat transfer coefficient for swept NACA 0012 airfoil models have been studied and reported in 2009, and the correlations will be used in the current study. The reference tests used a 91.4-cm chord, 152.4-cm span, adjustable sweep airfoil model of NACA 0012 profile at velocities of 100 and 150 knot and MVD of 44 and 93 mm. Scale-to-reference model size ratio was 1:2.4. All tests were conducted at 0deg angle of attack (AoA) and 45deg sweep angle. Ice shape comparison results were presented for stagnation-point freezing fractions in the range of 0.4 to 1.0. Preliminary results showed that good scaling was achieved for the conditions test by using the modified scaling methods developed for swept wing icing.

Gas-Centered Swirl Coaxial Liquid Injector Evaluations

NASA Technical Reports Server (NTRS)

Cohn, A. K.; Strakey, P. A.; Talley, D. G.

2005-01-01

Development of Liquid Rocket Engines is expensive. Extensive testing at large scales usually required. In order to verify engine lifetime, large number of tests required. Limited Resources available for development. Sub-scale cold-flow and hot-fire testing is extremely cost effective. Could be a necessary (but not sufficient) condition for long engine lifetime. Reduces overall costs and risk of large scale testing. Goal: Determine knowledge that can be gained from sub-scale cold-flow and hot-fire evaluations of LRE injectors. Determine relationships between cold-flow and hot-fire data.

Assessment of the spatial scaling behaviour of floods in the United Kingdom

NASA Astrophysics Data System (ADS)

Formetta, Giuseppe; Stewart, Elizabeth; Bell, Victoria

2017-04-01

Floods are among the most dangerous natural hazards, causing loss of life and significant damage to private and public property. Regional flood-frequency analysis (FFA) methods are essential tools to assess the flood hazard and plan interventions for its mitigation. FFA methods are often based on the well-known index flood method that assumes the invariance of the coefficient of variation of floods with drainage area. This assumption is equivalent to the simple scaling or self-similarity assumption for peak floods, i.e. their spatial structure remains similar in a particular, relatively simple, way to itself over a range of scales. Spatial scaling of floods has been evaluated at national scale for different countries such as Canada, USA, and Australia. According our knowledge. Such a study has not been conducted for the United Kingdom even though the standard FFA method there is based on the index flood assumption. In this work we present an integrated approach to assess of the spatial scaling behaviour of floods in the United Kingdom using three different methods: product moments (PM), probability weighted moments (PWM), and quantile analysis (QA). We analyse both instantaneous and daily annual observed maximum floods and performed our analysis both across the entire country and in its sub-climatic regions as defined in the Flood Studies Report (NERC, 1975). To evaluate the relationship between the k-th moments or quantiles and the drainage area we used both regression with area alone and multiple regression considering other explanatory variables to account for the geomorphology, amount of rainfall, and soil type of the catchments. The latter multiple regression approach was only recently demonstrated being more robust than the traditional regression with area alone that can lead to biased estimates of scaling exponents and misinterpretation of spatial scaling behaviour. We tested our framework on almost 600 rural catchments in UK considered as entire region and split in 11 sub-regions with 50 catchments per region on average. Preliminary results from the three different spatial scaling methods are generally in agreement and indicate that: i) only some of the peak flow variability is explained by area alone (approximately 50% for the entire country and ranging between the 40% and 70% for the sub-regions); ii) this percentage increases to 90% for the entire country and ranges between 80% and 95% for the sub-regions when the multiple regression is used; iii) the simple scaling hypothesis holds in all sub-regions with the exception of weak multi-scaling found in the regions 2 (North), and 5 and 6 (South East). We hypothesize that these deviations can be explained by heterogeneity in large scale precipitation and by the influence of the soil type (predominantly chalk) on the flood formation process in regions 5 and 6.

[Evaluation on the validity and reliability of the Diabetes Self-management Knowledge, Attitude, and Behavior Assessment Scale (DSKAB)].

PubMed

Liu, Xiaoli; Dai, Long; Chen, Bo; Feng, Nongping; Wu, Qianhui; Lin, Yonghai; Zhang, Lan; Tan, Dong; Zhang, Jinhua; Tu, Huijuan; Li, Changfeng; Wang, Wenjuan

2016-01-01

To evaluate the validity and reliability of Diabetes Self-management Knowledge, Attitude, and Behavior Assessment Scale (DSKAB). We selected 460 patients with diabetes in the community, used the scale which was after two rounds of the Delphi method and pilot study. Investigators surveyed the patients by the way of face to face. by draw lots, we selected 25 community diabetes randomly for repeating investigations after one week. The validity analyses included face validity, content validity, construct validity and discriminant validity. The reliability analyses included Cronbach's α coefficient, θ coefficient, Ω coefficient, split-half reliability and test-retest reliability. This study distributed a total of 460 questionnaires, reclaimed 442, qualified 432. The score of the scale was 254.59 ± 28.90, the scores of the knowledge, attitude, behavior sub-scales were 82.44 ± 11.24, 63.53 ± 5.77 and 108.61 ± 17.55, respectively. It had excellent face validity and content validity. The correlation coefficient was from 0.71 to 0.91 among three sub-scales and the scale, P<0.001. The common factor cumulative variance contribution rate of the scale and three sub-scales was from 57.28% to 67.19%, which achieved more than 50% of the approved standard, there was 25 common factors, 91 items of the total 98 items held factor loading ≥0.40 in its relevant common factor, it had good construct validity. The scores of high group and low group in three sub-scales were: knowledge (91.12 ± 3.62) and (69.96 ± 11.20), attitude (68.75 ± 4.51) and (58.79 ± 4.87), behavior (129.38 ± 8.53) and (89.65 ± 11.34),mean scores of three sub-scales were apparently different, which compared between high score group and low score group, the t value were - 19.45, -16.24 and -30.29, respectively, P<0.001, and it had good discriminant validity. The Cronbach's α coefficient of the scale and three sub-scales was from 0.79 to 0.93, the θ coefficient was from 0.86 to 0.95, the Ω coefficient was from 0.90 to 0.98, split-half reliability was from 0.89 to 0.95.Test-retest reliability of the scale was 0.51;the three sub-scales was from 0.46 to 0.52, P<0.05. The validity and reliability of the Diabetes Self-management Knowledge, Attitude, and Behavior Assessment Scale are excellent, which is a suitable instrument to evaluate the self-management for patients with diabetes.

Computational Analyses in Support of Sub-scale Diffuser Testing for the A-3 Facility. Part 3; Aero-Acoustic Analyses and Experimental Validation

NASA Technical Reports Server (NTRS)

Allgood, Daniel C.; Graham, Jason S.; McVay, Greg P.; Langford, Lester L.

2008-01-01

A unique assessment of acoustic similarity scaling laws and acoustic analogy methodologies in predicting the far-field acoustic signature from a sub-scale altitude rocket test facility at the NASA Stennis Space Center was performed. A directional, point-source similarity analysis was implemented for predicting the acoustic far-field. In this approach, experimental acoustic data obtained from "similar" rocket engine tests were appropriately scaled using key geometric and dynamic parameters. The accuracy of this engineering-level method is discussed by comparing the predictions with acoustic far-field measurements obtained. In addition, a CFD solver was coupled with a Lilley's acoustic analogy formulation to determine the improvement of using a physics-based methodology over an experimental correlation approach. In the current work, steady-state Reynolds-averaged Navier-Stokes calculations were used to model the internal flow of the rocket engine and altitude diffuser. These internal flow simulations provided the necessary realistic input conditions for external plume simulations. The CFD plume simulations were then used to provide the spatial turbulent noise source distributions in the acoustic analogy calculations. Preliminary findings of these studies will be discussed.

Biological Systems for Hydrogen Photoproduction (Presentation)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghirardi, M. L.

2012-05-01

This presentation summarizes NREL biological systems for hydrogen photoproduction work for the DOE Hydrogen and Fuel Cells Program Annual Merit Review and Peer Evaluation Meeting, May 14-18, 2012. General goal is develop photobiological systems for large-scale, low cost and efficient H{sub 2} production from water (barriers AH, AI and AJ). Specific tasks are: (1) Address the O{sub 2} sensitivity of hydrogenases that prevent continuity of H{sub 2} photoproduction under aerobic, high solar-to-hydrogen (STH) light conversion efficiency conditions; and (2) Utilize a limited STH H{sub 2}-producing method (sulfur deprivation) as a platform to address or test other factors limiting commercial algalmore » H{sub 2} photoproduction, including low rates due to biochemical and engineering mechanisms.« less

THE ARECIBO LEGACY FAST ALFA SURVEY. X. THE H I MASS FUNCTION AND {Omega}{sub H{sub i}} FROM THE 40% ALFALFA SURVEY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martin, Ann M.; Papastergis, Emmanouil; Giovanelli, Riccardo

The Arecibo Legacy Fast ALFA (ALFALFA) survey has completed source extraction for 40% of its total sky area, resulting in the largest sample of H I-selected galaxies to date. We measure the H I mass function from a sample of 10,119 galaxies with 6.2 < log (M{sub H{sub i}}/M{sub sun}) < 11.0 and with well-described mass errors that accurately reflect our knowledge of low-mass systems. We characterize the survey sensitivity and its dependence on profile velocity width, the effect of large-scale structure, and the impact of radio frequency interference in order to calculate the H I mass function with bothmore » the 1/V{sub max} and 2DSWML methods. We also assess a flux-limited sample to test the robustness of the methods applied to the full sample. These measurements are in excellent agreement with one another; the derived Schechter function parameters are {phi}{sub *} (h {sup 3}{sub 70} Mpc{sup -3} dex{sup -1}) = 4.8 {+-} 0.3 x 10{sup -3}, log (M{sub *}/M{sub sun}) + 2 log h{sub 70} = 9.96 {+-} 0.02, and {alpha} = -1.33 {+-} 0.02. We find {Omega}{sub H{sub i}}= 4.3 {+-} 0.3 x10{sup -4} h {sup -1}{sub 70}, 16% larger than the 2005 HIPASS result, and our Schechter function fit extrapolated to log (M{sub H{sub i}}/M{sub sun}) = 11.0 predicts an order of magnitude more galaxies than HIPASS. The larger values of {Omega}{sub H{sub i}} and of M{sub *} imply an upward adjustment for estimates of the detection rate of future large-scale H I line surveys with, e.g., the Square Kilometer Array. A comparison with simulated galaxies from the Millennium Run and a treatment of photoheating as a method of baryon removal from H I-selected halos indicate that the disagreement between dark matter mass functions and baryonic mass functions may soon be resolved.« less

Local unitary transformation method toward practical electron correlation calculations with scalar relativistic effect in large-scale molecules

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seino, Junji; Nakai, Hiromi, E-mail: nakai@waseda.jp; Research Institute for Science and Engineering, Waseda University, 3-4-1 Okubo, Shinjuku-ku, Tokyo 169-8555

In order to perform practical electron correlation calculations, the local unitary transformation (LUT) scheme at the spin-free infinite-order Douglas–Kroll–Hess (IODKH) level [J. Seino and H. Nakai, J. Chem. Phys.136, 244102 (2012); J. Seino and H. Nakai, J. Chem. Phys.137, 144101 (2012)], which is based on the locality of relativistic effects, has been combined with the linear-scaling divide-and-conquer (DC)-based Hartree–Fock (HF) and electron correlation methods, such as the second-order Møller–Plesset (MP2) and the coupled cluster theories with single and double excitations (CCSD). Numerical applications in hydrogen halide molecules, (HX){sub n} (X = F, Cl, Br, and I), coinage metal chain systems,more » M{sub n} (M = Cu and Ag), and platinum-terminated polyynediyl chain, trans,trans-((p-CH{sub 3}C{sub 6}H{sub 4}){sub 3}P){sub 2}(C{sub 6}H{sub 5})Pt(C≡C){sub 4}Pt(C{sub 6}H{sub 5})((p-CH{sub 3}C{sub 6}H{sub 4}){sub 3}P){sub 2}, clarified that the present methods, namely DC-HF, MP2, and CCSD with the LUT-IODKH Hamiltonian, reproduce the results obtained using conventional methods with small computational costs. The combination of both LUT and DC techniques could be the first approach that achieves overall quasi-linear-scaling with a small prefactor for relativistic electron correlation calculations.« less

Modeling and Evaluation of Geophysical Methods for Monitoring and Tracking CO2 Migration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daniels, Jeff

2012-11-30

Geological sequestration has been proposed as a viable option for mitigating the vast amount of CO{sub 2} being released into the atmosphere daily. Test sites for CO{sub 2} injection have been appearing across the world to ascertain the feasibility of capturing and sequestering carbon dioxide. A major concern with full scale implementation is monitoring and verifying the permanence of injected CO{sub 2}. Geophysical methods, an exploration industry standard, are non-invasive imaging techniques that can be implemented to address that concern. Geophysical methods, seismic and electromagnetic, play a crucial role in monitoring the subsurface pre- and post-injection. Seismic techniques have beenmore » the most popular but electromagnetic methods are gaining interest. The primary goal of this project was to develop a new geophysical tool, a software program called GphyzCO2, to investigate the implementation of geophysical monitoring for detecting injected CO{sub 2} at test sites. The GphyzCO2 software consists of interconnected programs that encompass well logging, seismic, and electromagnetic methods. The software enables users to design and execute 3D surface-to-surface (conventional surface seismic) and borehole-to-borehole (cross-hole seismic and electromagnetic methods) numerical modeling surveys. The generalized flow of the program begins with building a complex 3D subsurface geological model, assigning properties to the models that mimic a potential CO{sub 2} injection site, numerically forward model a geophysical survey, and analyze the results. A test site located in Warren County, Ohio was selected as the test site for the full implementation of GphyzCO2. Specific interest was placed on a potential reservoir target, the Mount Simon Sandstone, and cap rock, the Eau Claire Formation. Analysis of the test site included well log data, physical property measurements (porosity), core sample resistivity measurements, calculating electrical permittivity values, seismic data collection, and seismic interpretation. The data was input into GphyzCO2 to demonstrate a full implementation of the software capabilities. Part of the implementation investigated the limits of using geophysical methods to monitor CO{sub 2} injection sites. The results show that cross-hole EM numerical surveys are limited to under 100 meter borehole separation. Those results were utilized in executing numerical EM surveys that contain hypothetical CO{sub 2} injections. The outcome of the forward modeling shows that EM methods can detect the presence of CO{sub 2}.« less

A Sub-filter Scale Noise Equation far Hybrid LES Simulations

NASA Technical Reports Server (NTRS)

Goldstein, Marvin E.

2006-01-01

Hybrid LES/subscale modeling approaches have an important advantage over the current noise prediction methods in that they only involve modeling of the relatively universal subscale motion and not the configuration dependent larger scale turbulence . Previous hybrid approaches use approximate statistical techniques or extrapolation methods to obtain the requisite information about the sub-filter scale motion. An alternative approach would be to adopt the modeling techniques used in the current noise prediction methods and determine the unknown stresses from experimental data. The present paper derives an equation for predicting the sub scale sound from information that can be obtained with currently available experimental procedures. The resulting prediction method would then be intermediate between the current noise prediction codes and previously proposed hybrid techniques.

A high accuracy femto-/picosecond laser damage test facility dedicated to the study of optical thin films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mangote, B.; Gallais, L.; Zerrad, M.

2012-01-15

A laser damage test facility delivering pulses from 100 fs to 3 ps and designed to operate at 1030 nm is presented. The different details of its implementation and performances are given. The originality of this system relies the online damage detection system based on Nomarski microscopy and the use of a non-conventional energy detection method based on the utilization of a cooled CCD that offers the possibility to obtain the laser induced damage threshold (LIDT) with high accuracy. Applications of this instrument to study thin films under laser irradiation are presented. Particularly the deterministic behavior of the sub-picosecond damagemore » is investigated in the case of fused silica and oxide films. It is demonstrated that the transition of 0-1 damage probability is very sharp and the LIDT is perfectly deterministic at few hundreds of femtoseconds. The damage process in dielectric materials being the results of electronic processes, specific information such as the material bandgap is needed for the interpretation of results and applications of scaling laws. A review of the different approaches for the estimation of the absorption gap of optical dielectric coatings is conducted and the results given by the different methods are compared and discussed. The LIDT and gap of several oxide materials are then measured with the presented instrument: Al{sub 2}O{sub 3}, Nb{sub 2}O{sub 5}, HfO{sub 2}, SiO{sub 2}, Ta{sub 2}O{sub 5}, and ZrO{sub 2}. The obtained relation between the LIDT and gap at 1030 nm confirms the linear evolution of the threshold with the bandgap that exists at 800 nm, and our work expands the number of tested materials.« less

Solar Confocal Interferometers for Sub-Picometer-Resolution Spectral Filters

NASA Technical Reports Server (NTRS)

Gary, G. Allen; Pietraszewski, Chris; West, Edward A.; Dines, Terence C.

2006-01-01

The confocal Fabry-Perot interferometer allows sub-picometer spectral resolution of Fraunhofer line profiles. Such high spectral resolution is needed to keep pace with the higher spatial resolution of the new set of large-aperture solar telescopes. The line-of-sight spatial resolution derived for line profile inversions would then track the improvements of the transverse spatial scale provided by the larger apertures. The confocal interferometer's unique properties allow a simultaneous increase in both etendue and spectral power. Methods: We have constructed and tested two confocal interferometers. Conclusions: In this paper we compare the confocal interferometer with other spectral imaging filters, provide initial design parameters, show construction details for two designs, and report on the laboratory test results for these interferometers, and propose a multiple etalon system for future testing of these units and to obtain sub-picometer spectral resolution information on the photosphere in both the visible and near-infrared.

Validation of the Korean Version of the Scales for Outcomes in Parkinson's Disease-Sleep

PubMed Central

2017-01-01

Background Sleep problems commonly occur in patients with Parkinson's disease (PD), and are associated with a lower quality of life. The aim of the current study was to translate the English version of the Scales for Outcomes in Parkinson's Disease-Sleep (SCOPA-S) into the Korean version of SCOPA-S (K-SCOPA-S), and to evaluate its reliability and validity for use by Korean-speaking patients with PD. Methods In total, 136 patients with PD from 27 movement disorder centres of university-affiliated hospitals in Korea were enrolled in this study. They were assessed using SCOPA, Hoehn and Yahr Scale (HYS), Unified Parkinson's Disease Rating Scale (UPDRS), Parkinson's Disease Sleep Scale 2nd version (PDSS-2), Non-motor Symptoms Scale (NMSS), Montgomery Asberg Depression Scale (MADS), 39-item Parkinson's Disease Questionnaire (PDQ39), Neurogenic Orthostatic Hypotension Questionnaire (NOHQ), and Rapid Eye Movement Sleep Behaviour Disorder Questionnaire (RBDQ). The test-retest reliability was assessed over a time interval of 10–14 days. Results The internal consistency (Cronbach's α-coefficients) of K-SCOPA-S was 0.88 for nighttime sleep (NS) and 0.75 for daytime sleepiness (DS). Test-retest reliability was 0.88 and 0.85 for the NS and DS, respectively. There was a moderate correlation between the NS sub-score and PDSS-2 total score. The NS and DS sub-scores of K-SCOPA-S were correlated with motor scale such as HYS, and non-motor scales such as UPDRS I, UPDRS II, MADS, NMSS, PDQ39, and NOHQ while the DS sub-score was with RBDQ. Conclusion The K-SCOPA-S exhibited good reliability and validity for the assessment of sleep problems in the Korean patients with PD. PMID:29215823

Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

David W. Mazyck; Angela Lindner; CY Wu, Rick Sheahan, Ashok Jain

2007-06-30

Forest products provide essential resources for human civilization, including energy and materials. In processing forest products, however, unwanted byproducts, such as volatile organic compounds (VOCs) and hazardous air pollutants (HAPs) are generated. The goal of this study was to develop a cost effective and reliable air pollution control system to reduce VOC and HAP emissions from pulp, paper and paperboard mills and solid wood product facilities. Specifically, this work focused on the removal of VOCs and HAPs from high volume low concentration (HVLC) gases, particularly methanol since it is the largest HAP constituent in these gases. Three technologies were developedmore » and tested at the bench-scale: (1) A novel composite material of activated carbon coated with a photocatalyst titanium dioxide (TiO{sub 2}) (referred to as TiO{sub 2}-coated activated carbon or TiO{sub 2}/AC), (2) a novel silica gel impregnated with nanosized TiO{sub 2} (referred to as silica-titania composites or STC), and (3) biofiltration. A pilot-scale reactor was also fabricated and tested for methanol removal using the TiO{sub 2}/AC and STC. The technical feasibility of removing methanol with TiO{sub 2}/AC was studied using a composite synthesized via a spay desiccation method. The removal of methanol consists of two consecutive operation steps: removal of methanol using fixed-bed activated carbon adsorption and regeneration of spent activated carbon using in-situ photocatalytic oxidation. Regeneration using photocatalytic oxidation employed irradiation of the TiO{sub 2} catalyst with low-energy ultraviolet (UV) light. Results of this technical feasibility study showed that photocatalytic oxidation can be used to regenerate a spent TiO{sub 2}/AC adsorbent. A TiO{sub 2}/AC adsorbent was then developed using a dry impregnation method, which performed better than the TiO{sub 2}/AC synthesized using the spray desiccation method. The enhanced performance was likely a result of the better distribution of TiO2 particles on the activated carbon surface. A method for pore volume impregnation using microwave irradiation was also developed. A commercial microwave oven (800 W) was used as the microwave source. Under 2450 MHz microwave irradiation, TTIP was quickly hydrolyzed and anatase TiO2 was formed in a short time (< 20 minutes). Due to the volumetric heating and selective heating of microwave, the solvent and by-products were quickly removed which reduced energy consumption and processing time. Activated carbon and TiO{sub 2}/AC were also tested for the removal of hydrogen sulfide, which was chosen as the representative total reduced sulfur (TRS) species. The BioNuchar AC support itself was a good H{sub 2}S remover. After coating TiO{sub 2} by dry impregnation, H{sub 2}S removal efficiency of TiO{sub 2}/AC decreased compared with the virgin AC due to the change of surface pH. Under UV light irradiation, H{sub 2}S removal efficiency of TiO{sub 2}/AC composite doubled, and its sulfate conversion efficiency was higher than that of AC. The formation of sulfate is preferred since the sulfate can be removed from the composite by rising with water. A pilot-scale fluidized bed reactor was designed to test the efficiency of methanol oxidation with TiO{sub 2}/AC in the presence of UV light. TiO{sub 2}/AC was prepared using the spray desiccation method. The TiO{sub 2}/AC was pre-loaded with (1) methanol (equivalent to about 2%wt) and (2) methanol and water. When the TiO{sub 2}/AC loaded with methanol only was exposed to UV light for one hour in the reactor, most of the methanol remained in the carbon pores and, thus, was not oxidized. The TiO{sub 2}/AC loaded with methanol and water desorbed about 2/3 of the methanol from its pores during fluidization, however, only a small portion of this desorbed methanol was oxidized. A biofilter system employing biological activated carbon was developed for methanol removal. The biofilter contained a mixed packing with Westvaco BioNuchar granular activated carbon, perlite, Osmocote slow release ammonium nitrate pellets, and Agrasoke water crystals in a 4:2:1:1 ratio by volume. The biofilter was inoculated with a bacterial culture collected from a Florida pulp and paperboard plant. A non-inoculated biofilter column was also tested. Use of a biological inoculum enriched from biofilm in the pulp and paper process has the potential to enhance the performance of a GAC biofilter. During testing, packing material was removed from the inlet and oulet of the biofilters and analyzed for genetic diversity using molecular techniques. The biofilter inoculated with specifically-enhanced inoculum showed higher bacterial diversity for methylotrophs and all bacteria, as compared to a non-inoculated biofilter. Mixed methylotrophic cultures, selected as potential biofilter inocula, showed increased methanol removal with highest concentrations of nitrogen provided as nitrate.« less

The Relationship between Media Consumption and Health-Related Anxieties after the Fukushima Daiichi Nuclear Disaster

PubMed Central

Sugimoto, Amina; Nomura, Shuhei; Tsubokura, Masaharu; Matsumura, Tomoko; Muto, Kaori; Sato, Mikiko; Gilmour, Stuart

2013-01-01

Background The Fukushima Daiichi nuclear disaster caused a global panic by a release of harmful radionuclides. In a disaster setting, misusage of contemporary media sources available today can lead to disseminated incorrect information and panic. The study aims to build a scale which examines associations between media and individual anxieties, and to propose effective media usages for future disaster management. Methods The University of Tokyo collaborated with the Fukushima local government to conduct a radiation-health-seminar for a total of 1560 residents, at 12 different locations in Fukushima. A 13 item questionnaire collected once before and after a radiation-seminar was used on factor analysis to develop sub-scales for multiple regression models, to determine relationships between the sub-scales and media type consumed. A paired t–test was used to examine any changes in sub-scale of pre- and post-seminar scores. Results Three sub-scales were revealed and were associated with different media types: was with rumors, while concern for the future was positively associated with regional-newspapers and negatively with national-newspapers. Anxiety about social-disruption was associated with radio. The seminar had a significant effect on anxiety reduction for all the three sub-scales. Conclusion Different media types were associated with various heightened concerns, and that a radiation seminar was helpful to reduce anxieties in the post-disaster setting. By tailoring post-disaster messages via specific media types, i.e., radio, it may be possible to effectively convey important information, as well as to calm fears about particular elements of post-disaster recovery and to combat rumors. PMID:23967046

Lightning protection guidelines and test data for adhesively bonded aircraft structures

NASA Technical Reports Server (NTRS)

Pryzby, J. E.; Plumer, J. A.

1984-01-01

The highly competitive marketplace and increasing cost of energy has motivated manufacturers of general aviation aircraft to utilize composite materials and metal-to-metal bonding in place of conventional fasteners and rivets to reduce weight, obtain smoother outside surfaces and reduce drag. The purpose of this program is protection of these new structures from hazardous lightning effects. The program began with a survey of advance-technology materials and fabrication methods under consideration for future designs. Sub-element specimens were subjected to simulated lightning voltages and currents. Measurements of bond line voltages, electrical sparking, and mechanical strength degradation were made to comprise a data base of electrical properties for new technology materials and basic structural configurations. The second hase of the program involved tests on full scale wing structures which contained integral fuel tanks and which were representative of examples of new technology structures and fuel systems. The purpose of these tests was to provide a comparison between full scale structural measurements and those obtained from the sub-element specimens.

Construct Validity and Reliability of the SARA Gait and Posture Sub-scale in Early Onset Ataxia

PubMed Central

Lawerman, Tjitske F.; Brandsma, Rick; Verbeek, Renate J.; van der Hoeven, Johannes H.; Lunsing, Roelineke J.; Kremer, Hubertus P. H.; Sival, Deborah A.

2017-01-01

Aim: In children, gait and posture assessment provides a crucial marker for the early characterization, surveillance and treatment evaluation of early onset ataxia (EOA). For reliable data entry of studies targeting at gait and posture improvement, uniform quantitative biomarkers are necessary. Until now, the pediatric test construct of gait and posture scores of the Scale for Assessment and Rating of Ataxia sub-scale (SARA) is still unclear. In the present study, we aimed to validate the construct validity and reliability of the pediatric (SARAGAIT/POSTURE) sub-scale. Methods: We included 28 EOA patients [15.5 (6–34) years; median (range)]. For inter-observer reliability, we determined the ICC on EOA SARAGAIT/POSTURE sub-scores by three independent pediatric neurologists. For convergent validity, we associated SARAGAIT/POSTURE sub-scores with: (1) Ataxic gait Severity Measurement by Klockgether (ASMK; dynamic balance), (2) Pediatric Balance Scale (PBS; static balance), (3) Gross Motor Function Classification Scale -extended and revised version (GMFCS-E&R), (4) SARA-kinetic scores (SARAKINETIC; kinetic function of the upper and lower limbs), (5) Archimedes Spiral (AS; kinetic function of the upper limbs), and (6) total SARA scores (SARATOTAL; i.e., summed SARAGAIT/POSTURE, SARAKINETIC, and SARASPEECH sub-scores). For discriminant validity, we investigated whether EOA co-morbidity factors (myopathy and myoclonus) could influence SARAGAIT/POSTURE sub-scores. Results: The inter-observer agreement (ICC) on EOA SARAGAIT/POSTURE sub-scores was high (0.97). SARAGAIT/POSTURE was strongly correlated with the other ataxia and functional scales [ASMK (rs = -0.819; p < 0.001); PBS (rs = -0.943; p < 0.001); GMFCS-E&R (rs = -0.862; p < 0.001); SARAKINETIC (rs = 0.726; p < 0.001); AS (rs = 0.609; p = 0.002); and SARATOTAL (rs = 0.935; p < 0.001)]. Comorbid myopathy influenced SARAGAIT/POSTURE scores by concurrent muscle weakness, whereas comorbid myoclonus predominantly influenced SARAKINETIC scores. Conclusion: In young EOA patients, separate SARAGAIT/POSTURE parameters reveal a good inter-observer agreement and convergent validity, implicating the reliability of the scale. In perspective of incomplete discriminant validity, it is advisable to interpret SARAGAIT/POSTURE scores for comorbid muscle weakness. PMID:29326569

Evaluation of integration methods for hybrid simulation of complex structural systems through collapse

NASA Astrophysics Data System (ADS)

Del Carpio R., Maikol; Hashemi, M. Javad; Mosqueda, Gilberto

2017-10-01

This study examines the performance of integration methods for hybrid simulation of large and complex structural systems in the context of structural collapse due to seismic excitations. The target application is not necessarily for real-time testing, but rather for models that involve large-scale physical sub-structures and highly nonlinear numerical models. Four case studies are presented and discussed. In the first case study, the accuracy of integration schemes including two widely used methods, namely, modified version of the implicit Newmark with fixed-number of iteration (iterative) and the operator-splitting (non-iterative) is examined through pure numerical simulations. The second case study presents the results of 10 hybrid simulations repeated with the two aforementioned integration methods considering various time steps and fixed-number of iterations for the iterative integration method. The physical sub-structure in these tests consists of a single-degree-of-freedom (SDOF) cantilever column with replaceable steel coupons that provides repeatable highlynonlinear behavior including fracture-type strength and stiffness degradations. In case study three, the implicit Newmark with fixed-number of iterations is applied for hybrid simulations of a 1:2 scale steel moment frame that includes a relatively complex nonlinear numerical substructure. Lastly, a more complex numerical substructure is considered by constructing a nonlinear computational model of a moment frame coupled to a hybrid model of a 1:2 scale steel gravity frame. The last two case studies are conducted on the same porotype structure and the selection of time steps and fixed number of iterations are closely examined in pre-test simulations. The generated unbalance forces is used as an index to track the equilibrium error and predict the accuracy and stability of the simulations.

Large-scale production of anhydrous nitric acid and nitric acid solutions of dinitrogen pentoxide

DOEpatents

Harrar, Jackson E.; Quong, Roland; Rigdon, Lester P.; McGuire, Raymond R.

2001-01-01

A method and apparatus are disclosed for a large scale, electrochemical production of anhydrous nitric acid and N.sub.2 O.sub.5. The method includes oxidizing a solution of N.sub.2 O.sub.4 /aqueous-HNO.sub.3 at the anode, while reducing aqueous HNO.sub.3 at the cathode, in a flow electrolyzer constructed of special materials. N.sub.2 O.sub.4 is produced at the cathode and may be separated and recycled as a feedstock for use in the anolyte. The process is controlled by regulating the electrolysis current until the desired products are obtained. The chemical compositions of the anolyte and catholyte are monitored by measurement of the solution density and the concentrations of N.sub.2 O.sub.4.

Measurement Properties of Performance-Specific Pain Ratings of Patients Awaiting Total Joint Arthroplasty as a Consequence of Osteoarthritis

PubMed Central

Stratford, Paul W.; Kennedy, Deborah M.; Woodhouse, Linda J.; Spadoni, Gregory

2008-01-01

Purpose: To estimate the test–retest reliability of the Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC) pain sub-scale and performance-specific assessments of pain, as well as the association between these measures for patients awaiting primary total hip or knee arthroplasty as a consequence of osteoarthritis. Methods: A total of 164 patients awaiting unilateral primary hip or knee arthroplasty completed four performance measures (self-paced walk, timed up and go, stair test, six-minute walk) and the WOMAC. Scores for 22 of these patients provided test–retest reliability data. Estimates of test–retest reliability (Type 2,1 intraclass correlation coefficient [ICC] and standard error of measurement [SEM]) and the association between measures were examined. Results: ICC values for individual performance-specific pain ratings were between 0.70 and 0.86; SEM values were between 0.97 and 1.33 pain points. ICC estimates for the four-item performance pain ratings and the WOMAC pain sub-scale were 0.82 and 0.57 respectively. The correlation between the sum of the pain scores for the four performance measures and the WOMAC pain sub-scale was 0.62. Conclusion: Reliability estimates for the performance-specific assessments of pain using the numeric pain rating scale were consistent with values reported for patients with a spectrum of musculoskeletal conditions. The reliability estimate for the WOMAC pain sub-scale was lower than typically reported in the literature. The level of association between the WOMAC pain sub-scale and the various performance-specific pain scales suggests that the scores can be used interchangeably when applied to groups but not for individual patients. PMID:20145758

Construction, wind tunnel testing and data analysis for a 1/5 scale ultra-light wing model

NASA Technical Reports Server (NTRS)

James, Michael D.; Smith, Howard W.

1993-01-01

This report documents the construction, wind tunnel testing, and data analysis of a 1/5 scale ultra-light wing section. Wind tunnel testing provided accurate and meaningful lift, drag, and pitching moment data. This data was processed and graphically presented as follows: C(sub L) vs. gamma; C(sub D) vs. gamma; C(sub M) vs. gamma; and C(sub L) vs. C(sub D). The wing fabric flexure was found to be significant and its possible effects on aerodynamic data was discussed. The fabric flexure is directly related to wing angle of attack and airspeed. Different wing section shapes created by fabric flexure are presented with explanations of the types of pressures that act upon the wing surface. This report provides conclusive aerodynamic data for ultra-light wings.

Investigation of Vapor Cooling Enhancements for Applications on Large Cryogenic Systems

NASA Technical Reports Server (NTRS)

Ameen, Lauren; Zoeckler, Joseph

2017-01-01

The need to demonstrate and evaluate the effectiveness of heat interception methods for use on a relevant cryogenic propulsion stage at a system level has been identified. Evolvable Cryogenics (eCryo) Structural Heat Intercept, Insulation and Vibration Evaluation Rig (SHIIVER) will be designed with vehicle specific geometries (SLS Exploration Upper Stage (EUS) as guidance) and will be subjected to simulated space environments. One method of reducing structure-born heat leak being investigated utilizes vapor-based heat interception. Vapor-based heat interception could potentially reduce heat leak into liquid hydrogen propulsion tanks, increasing potential mission length or payload capability. Due to the high number of unknowns associated with the heat transfer mechanism and integration of vapor-based heat interception on a realistic large-scale skirt design, a sub-scale investigation was developed. The sub-project effort is known as the Small-scale Laboratory Investigation of Cooling Enhancements (SLICE). The SLICE aims to study, design, and test sub-scale multiple attachments and flow configuration concepts for vapor-based heat interception of structural skirts. SLICE will focus on understanding the efficiency of the heat transfer mechanism to the boil-off hydrogen vapor by varying the fluid network designs and configurations. Various analyses were completed in MATLAB, Excel VBA, and COMSOL Multiphysics to understand the optimum flow pattern for heat transfer and fluid dynamics. Results from these analyses were used to design and fabricate test article subsections of a large forward skirt with vapor cooling applied. The SLICE testing is currently being performed to collect thermal mechanical performance data on multiple skirt heat removal designs while varying inlet vapor conditions necessary to intercept a specified amount of heat for a given system. Initial results suggest that applying vapor-cooling provides a 50 heat reduction in conductive heat transmission along the skirt to the tank. The information obtained by SLICE will be used by the SHIIVER engineering team to design and implement vapor-based heat removal technology into the SHIIVER forward skirt hardware design.

Recent advances in small-scale mechanical property measurement by nanoindentation

DOE PAGES

Pharr, George Mathews

2015-08-25

Since its initial development in the early 1980’s [1], nanoindentation has matured into one of the premier testing techniques for measuring mechanical properties at the micrometer and sub-micrometer scales and has emerged as a critical tool that has helped to shape the nanotechnology revolution. At the heart of the technique are testing systems with simple but precise force actuators and displacement measuring devices that record the force–displacement record as a diamond indenter, usually the form of a pyramid or a sphere, is pressed into and withdrawn from a small region in the surface of a material of interest. The nano-scalemore » force–displacement data, which can be obtained with a spatial resolution as small as a few nanometers, contains a wealth of information about the local mechanical properties [2], [3] and [4]. This enables the mechanical characterization of very thin films, like those used in the semiconductor, magnetic storage, and hard coatings industries, as well as very small precipitates, particles and second phases, many of which may not exist in bulk form and cannot be characterized by traditional mechanical testing methods. Here, computer automation of nanoindentation testing systems now routinely provides for complete two-dimensional mapping of properties over regions stretching from sub-micron to millimeters in scale.« less

Space Launch System Base Heating Test: Sub-Scale Rocket Engine/Motor Design, Development & Performance Analysis

NASA Technical Reports Server (NTRS)

Mehta, Manish; Seaford, Mark; Kovarik, Brian; Dufrene, Aaron; Solly, Nathan

2014-01-01

ATA-002 Technical Team has successfully designed, developed, tested and assessed the SLS Pathfinder propulsion systems for the Main Base Heating Test Program. Major Outcomes of the Pathfinder Test Program: Reach 90% of full-scale chamber pressure Achieved all engine/motor design parameter requirements Reach steady plume flow behavior in less than 35 msec Steady chamber pressure for 60 to 100 msec during engine/motor operation Similar model engine/motor performance to full-scale SLS system Mitigated nozzle throat and combustor thermal erosion Test data shows good agreement with numerical prediction codes Next phase of the ATA-002 Test Program Design & development of the SLS OML for the Main Base Heating Test Tweak BSRM design to optimize performance Tweak CS-REM design to increase robustness MSFC Aerosciences and CUBRC have the capability to develop sub-scale propulsion systems to meet desired performance requirements for short-duration testing.

Attitude to the subject of chemistry in undergraduate nursing students at Fiji National University and Federation University, Australia.

PubMed

Brown, Stephen; Wakeling, Lara; Peck, Blake; Naiker, Mani; Hill, Dolores; Naidu, Keshni

2015-01-01

Attitude to the subject of chemistry was quantified in first-year undergraduate nursing students, at two geographically distinct universities. A purpose-designed diagnostic instrument (ASCI) was given to students at Federation University, Australia (n= 114), and at Fiji National University, Fiji (n=160). Affective and cognitive sub-scales within ASCI showed reasonable internal consistency. Cronbach's alpha for the cognitive sub-scale was 0.786 and 0.630, and 0.787 and 0.788 for affective sub-scale for the Federation University and Fiji National University students, respectively. Mean (SD) score for the cognitive sub-scale was 10.5 (5.6) and 15.2 (4.1) for students at Federation University and Fiji National University, respectively (P<0.001, t-test). Mean (SD) score for the affective sub-scale was 13.1 (5.1) and 20.7 (4.3) for students at Federation University and Fiji National University, respectively (P < 0.001, t-test). An exploratory factor analysis (n=274) confirmed a two-factor solution consistent with affective and cognitive sub-scales, each with good internal consistency. Quantifying attitude to chemistry in undergraduate nursing students using ASCI may have utility in assessing the impact of novel teaching strategies used in the education of nursing students in areas of bioscience and chemistry. However, geographically distinct populations of undergraduate nurses may show very different attitudes to chemistry.

Hypertension Knowledge-Level Scale (HK-LS): a study on development, validity and reliability.

PubMed

Erkoc, Sultan Baliz; Isikli, Burhanettin; Metintas, Selma; Kalyoncu, Cemalettin

2012-03-01

This study was conducted to develop a scale to measure knowledge about hypertension among Turkish adults. The Hypertension Knowledge-Level Scale (HK-LS) was generated based on content, face, and construct validity, internal consistency, test re-test reliability, and discriminative validity procedures. The final scale had 22 items with six sub-dimensions. The scale was applied to 457 individuals aged ≥ 18 years, and 414 of them were re-evaluated for test-retest reliability. The six sub-dimensions encompassed 60.3% of the total variance. Cronbach alpha coefficients were 0.82 for the entire scale and 0.92, 0.59, 0.67, 0.77, 0.72, and 0.76 for the sub-dimensions of definition, medical treatment, drug compliance, lifestyle, diet, and complications, respectively. The scale ensured internal consistency in reliability and construct validity, as well as stability over time. Significant relationships were found between knowledge score and age, gender, educational level, and history of hypertension of the participants. No correlation was found between knowledge score and working at an income-generating job. The present scale, developed to measure the knowledge level of hypertension among Turkish adults, was found to be valid and reliable.

The Effects of the Critical Ice Accretion on Airfoil and Wing Performance

NASA Technical Reports Server (NTRS)

Selig, Michael S.; Bragg, Michael B.; Saeed, Farooq

1998-01-01

In support of the NASA Lewis Modern Airfoils Ice Accretion Test Program, the University of Illinois at Urbana-Champaign provided expertise in airfoil design and aerodynamic analysis to determine the aerodynamic effect of ice accretion on modern airfoil sections. The effort has concentrated on establishing a design/testing methodology for "hybrid airfoils" or "sub-scale airfoils," that is, airfoils having a full-scale leading edge together with a specially designed and foreshortened aft section. The basic approach of using a full-scale leading edge with a foreshortened aft section was considered to a limited extent over 40 years ago. However, it was believed that the range of application of the method had not been fully exploited. Thus a systematic study was being undertaken to investigate and explore the range of application of the method so as to determine its overall potential.

Innovative Method for Developing a Helium Pressurant Tank Suitable for the Upper Stage Flight Experiment

NASA Technical Reports Server (NTRS)

DeLay, Tom K.; Munafo, Paul (Technical Monitor)

2001-01-01

The AFRL USFE project is an experimental test bed for new propulsion technologies. It will utilize ambient temperature fuel and oxidizers (Kerosene and Hydrogen peroxide). The system is pressure fed, not pump fed, and will utilize a helium pressurant tank to drive the system. Mr. DeLay has developed a method for cost effectively producing a unique, large pressurant tank that is not commercially available. The pressure vessel is a layered composite structure with an electroformed metallic permeation barrier. The design/process is scalable and easily adaptable to different configurations with minimal cost in tooling development 1/3 scale tanks have already been fabricated and are scheduled for testing. The full-scale pressure vessel (50" diameter) design will be refined based on the performance of the sub-scale tank. The pressure vessels have been designed to operate at 6,000 psi. a PV/W of 1.92 million is anticipated.

Validity of flowmeter data in heterogeneous alluvial aquifers

NASA Astrophysics Data System (ADS)

Bianchi, Marco

2017-04-01

Numerical simulations are performed to evaluate the impact of medium-scale sedimentary architecture and small-scale heterogeneity on the validity of the borehole flowmeter test, a widely used method for measuring hydraulic conductivity (K) at the scale required for detailed groundwater flow and solute transport simulations. Reference data from synthetic K fields representing the range of structures and small-scale heterogeneity typically observed in alluvial systems are compared with estimated values from numerical simulations of flowmeter tests. Systematic errors inherent in the flowmeter K estimates are significant when the reference K field structure deviates from the hypothetical perfectly stratified conceptual model at the basis of the interpretation method of flowmeter tests. Because of these errors, the true variability of the K field is underestimated and the distributions of the reference K data and log-transformed spatial increments are also misconstrued. The presented numerical analysis shows that the validity of flowmeter based K data depends on measureable parameters defining the architecture of the hydrofacies, the conductivity contrasts between the hydrofacies and the sub-facies-scale K variability. A preliminary geological characterization is therefore essential for evaluating the optimal approach for accurate K field characterization.

Method for making high-critical-current-density YBa.sub.2 Cu.sub.3 O.sub.7 superconducting layers on metallic substrates

DOEpatents

Feenstra, Roeland; Christen, David; Paranthaman, Mariappan

1999-01-01

A method is disclosed for fabricating YBa.sub.2 Cu.sub.3 O.sub.7 superconductor layers with the capability of carrying large superconducting currents on a metallic tape (substrate) supplied with a biaxially textured oxide buffer layer. The method represents a simplification of previously established techniques and provides processing requirements compatible with scale-up to long wire (tape) lengths and high processing speeds. This simplification has been realized by employing the BaF.sub.2 method to grow a YBa.sub.2 Cu.sub.3 O.sub.7 film on a metallic substrate having a biaxially textured oxide buffer layer.

LAB-SCALE DEMONSTRATION OF PLUTONIUM PURIFICATION BY ANION EXCHANGE, PLUTONIUM (IV) OXALATE PRECIPITATION, AND CALCINATION TO PLUTONIUM OXIDE TO SUPPORT THE MOX FEED MISSION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crowder, M.; Pierce, R.

2012-08-22

H-Canyon and HB-Line are tasked with the production of PuO{sub 2} from a feed of plutonium metal. The PuO{sub 2} will provide feed material for the MOX Fuel Fabrication Facility. After dissolution of the Pu metal in H-Canyon, the solution will be transferred to HB-Line for purification by anion exchange. Subsequent unit operations include Pu(IV) oxalate precipitation, filtration and calcination to form PuO{sub 2}. This report details the results from SRNL anion exchange, precipitation, filtration, calcination, and characterization tests, as requested by HB-Line1 and described in the task plan. This study involved an 80-g batch of Pu and employed testmore » conditions prototypical of HB-Line conditions, wherever feasible. In addition, this study integrated lessons learned from earlier anion exchange and precipitation and calcination studies. H-Area Engineering selected direct strike Pu(IV) oxalate precipitation to produce a more dense PuO{sub 2} product than expected from Pu(III) oxalate precipitation. One benefit of the Pu(IV) approach is that it eliminates the need for reduction by ascorbic acid. The proposed HB-Line precipitation process involves a digestion time of 5 minutes after the time (44 min) required for oxalic acid addition. These were the conditions during HB-line production of neptunium oxide (NpO{sub 2}). In addition, a series of small Pu(IV) oxalate precipitation tests with different digestion times were conducted to better understand the effect of digestion time on particle size, filtration efficiency and other factors. To test the recommended process conditions, researchers performed two nearly-identical larger-scale precipitation and calcination tests. The calcined batches of PuO{sub 2} were characterized for density, specific surface area (SSA), particle size, moisture content, and impurities. Because the 3013 Standard requires that the calcination (or stabilization) process eliminate organics, characterization of PuO{sub 2} batches monitored the presence of oxalate by thermogravimetric analysis-mass spectrometry (TGA-MS). To use the TGA-MS for carbon or oxalate content, some method development will be required. However, the TGA-MS is already used for moisture measurements. Therefore, SRNL initiated method development for the TGA-MS to allow quantification of oxalate or total carbon. That work continues at this time and is not yet ready for use in this study. However, the collected test data can be reviewed later as those analysis tools are available.« less

Single image super resolution algorithm based on edge interpolation in NSCT domain

NASA Astrophysics Data System (ADS)

Zhang, Mengqun; Zhang, Wei; He, Xinyu

2017-11-01

In order to preserve the texture and edge information and to improve the space resolution of single frame, a superresolution algorithm based on Contourlet (NSCT) is proposed. The original low resolution image is transformed by NSCT, and the directional sub-band coefficients of the transform domain are obtained. According to the scale factor, the high frequency sub-band coefficients are amplified by the interpolation method based on the edge direction to the desired resolution. For high frequency sub-band coefficients with noise and weak targets, Bayesian shrinkage is used to calculate the threshold value. The coefficients below the threshold are determined by the correlation among the sub-bands of the same scale to determine whether it is noise and de-noising. The anisotropic diffusion filter is used to effectively enhance the weak target in the low contrast region of the target and background. Finally, the high-frequency sub-band is amplified by the bilinear interpolation method to the desired resolution, and then combined with the high-frequency subband coefficients after de-noising and small target enhancement, the NSCT inverse transform is used to obtain the desired resolution image. In order to verify the effectiveness of the proposed algorithm, the proposed algorithm and several common image reconstruction methods are used to test the synthetic image, motion blurred image and hyperspectral image, the experimental results show that compared with the traditional single resolution algorithm, the proposed algorithm can obtain smooth edges and good texture features, and the reconstructed image structure is well preserved and the noise is suppressed to some extent.

Development and Demonstration of a Sulfate Precipitation Process for Hanford Waste Tank 241-AN-107

DOE Office of Scientific and Technical Information (OSTI.GOV)

SK Fiskum; DE Kurath; BM Rapko

2000-08-16

A series of precipitation experiments were conducted on Hanford waste tank 241-AN-107 samples in an effort to remove sulfate from the matrix. Calcium nitrate was added directly to AN-107 sub-samples to yield several combinations of Ca:CO{sub 3} mole ratios spanning a range of 0:1 to 3:1 to remove carbonate as insoluble CaCO{sub 3}. Similarly barium nitrate was added directly to the AN-107 aliquots, or to the calcium pretreated AN-107 aliquots, giving of Ba:SO{sub 4} mole ratios spanning a range of 1:1 to 5:1 to precipitate sulfate as BaSO{sub 4}. Initial bulk carbonate removal was required for successful follow-on barium sulfatemore » precipitation. A {ge} 1:1 mole ratio of Ca:CO{sub 3} was found to lower the carbonate concentration such that Ba would react preferentially with the sulfate. A follow-on 1:1 mole ratio of Ba:SO{sub 4} resulted in 70% sulfate removal. The experiment was scaled up with a 735-mL aliquot of AN-107 for more complete testing. Calcium carbonate and barium sulfate settling rates were determined and fates of selected cations, anions, and radionuclides were followed through the various process steps. Seventy percent of the sulfate was removed in the scale-up test while recovering 63% of the filtrate volume. Surprisingly, during the scale-up test a sub-sample of the CaCO{sub 3}/241-AN-107 slurry was found to lose fluidity upon standing for {le} 2 days. Metathesis with BaCO{sub 3} at ambient temperature was also evaluated using batch contacts at various BaCO{sub 3}:SO{sub 4} mole ratios with no measurable success.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The NOXSO Process uses a regenerable sorbent that removes SO{sub 2} and NO{sub x} simultaneously from flue gas. The sorbent is a stabilized {gamma}-alumina bed impregnated with sodium carbonate. The process was successfully tested at three different scales, equivalent to 0.017, 0.06 and 0.75 MW of flue gas generated from a coal-fired power plant. The Proof-of-Concept (POC) Test is the last test prior to a full-scale demonstration. A slip stream of flue gas equivalent to a 5 MW coal-fired power plant was used for the POC test. This paper summarizes the NOXSO POC plant and its test results.

A depth-first search algorithm to compute elementary flux modes by linear programming.

PubMed

Quek, Lake-Ee; Nielsen, Lars K

2014-07-30

The decomposition of complex metabolic networks into elementary flux modes (EFMs) provides a useful framework for exploring reaction interactions systematically. Generating a complete set of EFMs for large-scale models, however, is near impossible. Even for moderately-sized models (<400 reactions), existing approaches based on the Double Description method must iterate through a large number of combinatorial candidates, thus imposing an immense processor and memory demand. Based on an alternative elementarity test, we developed a depth-first search algorithm using linear programming (LP) to enumerate EFMs in an exhaustive fashion. Constraints can be introduced to directly generate a subset of EFMs satisfying the set of constraints. The depth-first search algorithm has a constant memory overhead. Using flux constraints, a large LP problem can be massively divided and parallelized into independent sub-jobs for deployment into computing clusters. Since the sub-jobs do not overlap, the approach scales to utilize all available computing nodes with minimal coordination overhead or memory limitations. The speed of the algorithm was comparable to efmtool, a mainstream Double Description method, when enumerating all EFMs; the attrition power gained from performing flux feasibility tests offsets the increased computational demand of running an LP solver. Unlike the Double Description method, the algorithm enables accelerated enumeration of all EFMs satisfying a set of constraints.

A comprehensive approach to psychometric assessment of instruments used in dementia educational interventions for health professionals: a cross-sectional study.

PubMed

Wang, Yao; Xiao, Lily Dongxia; He, Guo-Ping

2015-02-01

Suboptimal care for people with dementia in hospital settings has been reported and is attributed to the lack of knowledge and inadequate attitudes in dementia care among health professionals. Educational interventions have been widely used to improve care outcomes; however, Chinese-language instruments used in dementia educational interventions for health professionals are lacking. The aims of this study were to select, translate and evaluate instruments used in dementia educational interventions for Chinese health professionals in acute-care hospitals. A cross-sectional study design was used. A modified stratified random sampling was used to recruit 442 participants from different levels of hospitals in Changsha, China. Dementia care competence was used as a framework for the selection and evaluation of Alzheimer's Disease Knowledge Scale and Dementia Care Attitudes Scale for health professionals in the study. These two scales were translated into Chinese using forward and back translation method. Content validity, test-retest reliability and internal consistency were assessed. Construct validity was tested using exploratory factor analysis. Known-group validity was established by comparing scores of Alzheimer's Disease Knowledge Scale and Dementia Care Attitudes Scale in two sub-groups. A person-centred care scale was utilised as a gold standard to establish concurrent validity of these two scales. Results demonstrated acceptable content validity, internal consistency, test-retest reliability and concurrent validity. Exploratory factor analysis presented a single-factor structure of the Chinese Alzheimer's Disease Knowledge Scale and a two-factor structure of the Chinese Dementia Care Attitudes Scale, supporting the conceptual dimensions of the original scales. The Chinese Alzheimer's Disease Knowledge Scale and Chinese Dementia Care Attitudes Scale demonstrated known-group validity evidenced by significantly higher scores identified from the sub-group with a longer work experience compared to those in the sub-group with less work experience. The use of dementia care competence as a framework to inform the selection and evaluation of instruments used in dementia educational interventions for health professionals has wide applicability in other areas. The results support that Chinese Alzheimer's Disease Knowledge Scale and Chinese Dementia Care Attitudes Scale are reliable and valid instruments for health professionals to use in acute-care settings. Copyright © 2014 Elsevier Ltd. All rights reserved.

Constrained optimization framework for interface-aware sub-scale dynamics models for voids closure in Lagrangian hydrodynamics

DOE PAGES

Barlow, Andrew; Klima, Matej; Shashkov, Mikhail

2018-04-02

In hydrocodes, voids are used to represent vacuum and model free boundaries between vacuum and real materials. We give a systematic description of a new treatment of void closure in the framework of the multimaterial arbitrary Lagrangian–Eulerian (ALE) methods. This includes a new formulation of the interface-aware sub-scale-dynamics (IA-SSD) closure model for multimaterial cells with voids, which is used in the Lagrangian stage of our indirect ALE scheme. The results of the comprehensive testing of the new model are presented for one- and two-dimensional multimaterial calculations in the presence of voids. Finally, we also present a sneak peek of amore » realistic shaped charge calculation in the presence of voids and solids.« less

Constrained optimization framework for interface-aware sub-scale dynamics models for voids closure in Lagrangian hydrodynamics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barlow, Andrew; Klima, Matej; Shashkov, Mikhail

In hydrocodes, voids are used to represent vacuum and model free boundaries between vacuum and real materials. We give a systematic description of a new treatment of void closure in the framework of the multimaterial arbitrary Lagrangian–Eulerian (ALE) methods. This includes a new formulation of the interface-aware sub-scale-dynamics (IA-SSD) closure model for multimaterial cells with voids, which is used in the Lagrangian stage of our indirect ALE scheme. The results of the comprehensive testing of the new model are presented for one- and two-dimensional multimaterial calculations in the presence of voids. Finally, we also present a sneak peek of amore » realistic shaped charge calculation in the presence of voids and solids.« less

DEVELOPMENT OF PLUTONIUM-BEARING FUEL MATERIALS. Progress Report, October 1-December 31, 1961

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1962-10-31

Continued effort is reported on preparation and characterization of PuO/ sub 2/ and UO/sub 2/-- PuO/sub 2/ mixtures. Sintering and characterization of pellets for irradiation tests was emphasized, and efforts were also devoted to plasma torch production of spherical PuO /sub 2/ and coating of oxide materials. PuO/sub 2/ produced by the oxalate process from low concentration feed contains agglomerates which are not readily broken down, while that produced from normal feed contains larger agglomerates which are easily dispersed ultrasonically, and are more easily calcined. The water filtration method for determining total porosity of powders was adapted for use withmore » PuO/sub 2/. Moisture pickup studies show that the problems encountered with PuO/sub 2/ are similar to those found in handling ceramic-grade UO/. Reproducibility tests carried out on UO/sub 2/--PuO/ sub 2/ mixtures indicate that production methods are satisfactory. Lab-scale experiments on production of PuO/sub 2/-- UO/sub 2/feed for the plasma torch indicate that further work is worthwhile. Adaptation of a potentiometric filtration for Pu is reported. A twophase microstructure found in PuO/ after sintering in N6% H atmosphere was identified as PuO/sub 2/ and cubic Pu/sub 2/O/ sub 3/. Spherical particles were produced in the plasma torch using crushed or preformed high-fired particles. Spherical particles of PuO/sub 2/ were also produced by a multi-step process of drying, pressing, granulation, sizing, shaping, and sintering. Reactor physics studies were continued to determine the effect of cross section assumptions on the calculated behavior of Pu-fueled near- thermal reactor systems. It was concluded that relatively long core life (reactivity limiting) is attainable with these systems. (J.R.D.)« less

Testing two methods to create comparable scale scores between the Job Content Questionnaire (JCQ) and JCQ-like questionnaires in the European JACE Study.

PubMed

Karasek, Robert; Choi, BongKyoo; Ostergren, Per-Olof; Ferrario, Marco; De Smet, Patrick

2007-01-01

Scale comparative properties of "JCQ-like" questionnaires with respect to the JCQ have been little known. Assessing validity and reliability of two methods for generating comparable scale scores between the Job Content Questionnaire (JCQ) and JCQ-like questionnaires in sub-populations of the large Job Stress, Absenteeism and Coronary Heart Disease European Cooperative (JACE) study: the Swedish version of Demand-Control Questionnaire (DCQ) and a transformed Multinational Monitoring of Trends and Determinants in Cardiovascular Disease Project (MONICA) questionnaire. A random population sample of all Malmo males and females aged 52-58 (n = 682) years was given a new test questionnaire with both instruments (the JCQ and the DCQ). Comparability-facilitating algorithms were created (Method I). For the transformed Milan MONICA questionnaire, a simple weighting system was used (Method II). The converted scale scores from the JCQ-like questionnaires were found to be reliable and highly correlated to those of the original JCQ. However, agreements for the high job strain group between the JCQ and the DCQ, and between the JCQ and the DCQ (Method I applied) were only moderate (Kappa). Use of a multiple level job strain scale generated higher levels of job strain agreement, as did a new job strain definition that excludes the intermediate levels of the job strain distribution. The two methods were valid and generally reliable.

An Acoustical Comparison of Sub-Scale and Full-Scale Far-Field Measurements for the Reusable Solid Rocket Motor

NASA Technical Reports Server (NTRS)

Haynes, Jared; Kenny, R. Jeremy

2010-01-01

Recently, members of the Marshall Space Flight Center (MSFC) Fluid Dynamics Branch and Wyle Labs measured far-field acoustic data during a series of three Reusable Solid Rocket Motor (RSRM) horizontal static tests conducted in Promontory, Utah. The test motors included the Technical Evaluation Motor 13 (TEM-13), Flight Verification Motor 2 (FVM-2), and the Flight Simulation Motor 15 (FSM-15). Similar far-field data were collected during horizontal static tests of sub-scale solid rocket motors at MSFC. Far-field acoustical measurements were taken at multiple angles within a circular array centered about the nozzle exit plane, each positioned at a radial distance of 80 nozzle-exit-diameters from the nozzle. This type of measurement configuration is useful for calculating rocket noise characteristics such as those outlined in the NASA SP-8072 "Acoustic Loads Generated by the Propulsion System." Acoustical scaling comparisons are made between the test motors, with particular interest in the Overall Sound Power, Acoustic Efficiency, Non-dimensional Relative Sound Power Spectrum, and Directivity. Since most empirical data in the NASA SP-8072 methodology is derived from small rockets, this investigation provides an opportunity to check the data collapse between a sub-scale and full-scale rocket motor.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Casagrande, L.; Asplund, M.; Ramirez, I.

Solar infrared colors provide powerful constraints on the stellar effective temperature scale, but they must be measured with both accuracy and precision in order to do so. We fulfill this requirement by using line-depth ratios to derive in a model-independent way the infrared colors of the Sun, and we use the latter to test the zero point of the Casagrande et al. effective temperature scale, confirming its accuracy. Solar colors in the widely used Two Micron All Sky Survey (2MASS) JHK{sub s} and WISE W1-4 systems are provided: (V - J){sub Sun} = 1.198, (V - H){sub Sun} = 1.484,more » (V - K{sub s} ){sub Sun} = 1.560, (J - H){sub Sun} = 0.286, (J - K{sub s} ){sub Sun} = 0.362, (H - K{sub s} ){sub Sun} = 0.076, (V - W1){sub Sun} = 1.608, (V - W2){sub Sun} = 1.563, (V - W3){sub Sun} = 1.552, and (V - W4){sub Sun} = 1.604. A cross-check of the effective temperatures derived implementing 2MASS or WISE magnitudes in the infrared flux method confirms that the absolute calibration of the two systems agrees within the errors, possibly suggesting a 1% offset between the two, thus validating extant near- and mid-infrared absolute calibrations. While 2MASS magnitudes are usually well suited to derive T{sub eff}, we find that a number of bright, solar-like stars exhibit anomalous WISE colors. In most cases, this effect is spurious and can be attributed to lower-quality measurements, although for a couple of objects (3% {+-} 2% of the total sample) it might be real, and may hint at the presence of warm/hot debris disks.« less

Sub-Selective Quantization for Learning Binary Codes in Large-Scale Image Search.

PubMed

Li, Yeqing; Liu, Wei; Huang, Junzhou

2018-06-01

Recently with the explosive growth of visual content on the Internet, large-scale image search has attracted intensive attention. It has been shown that mapping high-dimensional image descriptors to compact binary codes can lead to considerable efficiency gains in both storage and performing similarity computation of images. However, most existing methods still suffer from expensive training devoted to large-scale binary code learning. To address this issue, we propose a sub-selection based matrix manipulation algorithm, which can significantly reduce the computational cost of code learning. As case studies, we apply the sub-selection algorithm to several popular quantization techniques including cases using linear and nonlinear mappings. Crucially, we can justify the resulting sub-selective quantization by proving its theoretic properties. Extensive experiments are carried out on three image benchmarks with up to one million samples, corroborating the efficacy of the sub-selective quantization method in terms of image retrieval.

Sub-core permeability and relative permeability characterization with Positron Emission Tomography

NASA Astrophysics Data System (ADS)

Zahasky, C.; Benson, S. M.

2017-12-01

This study utilizes preclinical micro-Positron Emission Tomography (PET) to image and quantify the transport behavior of pulses of a conservative aqueous radiotracer injected during single and multiphase flow experiments in a Berea sandstone core with axial parallel bedding heterogeneity. The core is discretized into streamtubes, and using the micro-PET data, expressions are derived from spatial moment analysis for calculating sub-core scale tracer flux and pore water velocity. Using the flux and velocity data, it is then possible to calculate porosity and saturation from volumetric flux balance, and calculate permeability and water relative permeability from Darcy's law. Full 3D simulations are then constructed based on this core characterization. Simulation results are compared with experimental results in order to test the assumptions of the simple streamtube model. Errors and limitations of this analysis will be discussed. These new methods of imaging and sub-core permeability and relative permeability measurements enable experimental quantification of transport behavior across scales.

Ground Testing a Nuclear Thermal Rocket: Design of a sub-scale demonstration experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

David Bedsun; Debra Lee; Margaret Townsend

In 2008, the NASA Mars Architecture Team found that the Nuclear Thermal Rocket (NTR) was the preferred propulsion system out of all the combinations of chemical propulsion, solar electric, nuclear electric, aerobrake, and NTR studied. Recently, the National Research Council committee reviewing the NASA Technology Roadmaps recommended the NTR as one of the top 16 technologies that should be pursued by NASA. One of the main issues with developing a NTR for future missions is the ability to economically test the full system on the ground. In the late 1990s, the Sub-surface Active Filtering of Exhaust (SAFE) concept was firstmore » proposed by Howe as a method to test NTRs at full power and full duration. The concept relied on firing the NTR into one of the test holes at the Nevada Test Site which had been constructed to test nuclear weapons. In 2011, the cost of testing a NTR and the cost of performing a proof of concept experiment were evaluated.« less

Catalyzed CO.sub.2-transport membrane on high surface area inorganic support

DOEpatents

Liu, Wei

2014-05-06

Disclosed are membranes and methods for making the same, which membranes provide improved permeability, stability, and cost-effective manufacturability, for separating CO.sub.2 from gas streams such as flue gas streams. High CO.sub.2 permeation flux is achieved by immobilizing an ultra-thin, optionally catalyzed fluid layer onto a meso-porous modification layer on a thin, porous inorganic substrate such as a porous metallic substrate. The CO.sub.2-selective liquid fluid blocks non-selective pores, and allows for selective absorption of CO.sub.2 from gas mixtures such as flue gas mixtures and subsequent transport to the permeation side of the membrane. Carbon dioxide permeance levels are in the order of 1.0.times.10.sup.-6 mol/(m.sup.2sPa) or better. Methods for making such membranes allow commercial scale membrane manufacturing at highly cost-effective rates when compared to conventional commercial-scale CO.sub.2 separation processes and equipment for the same and such membranes are operable on an industrial use scale.

Flow Separation Control on A Full-Scale Vertical Tail Model Using Sweeping Jet Actuators

NASA Technical Reports Server (NTRS)

Andino, Marlyn Y.; Lin, John C.; Washburn, Anthony E.; Whalen, Edward A.; Graff, Emilio C.; Wygnanski, Israel J.

2015-01-01

This paper describes test results of a joint NASA/Boeing research effort to advance Active Flow Control (AFC) technology to enhance aerodynamic efficiency. A full-scale Boeing 757 vertical tail model equipped with sweeping jets AFC was tested at the National Full-Scale Aerodynamics Complex 40- by 80-Foot Wind Tunnel at NASA Ames Research Center. The flow separation control optimization was performed at 100 knots, a maximum rudder deflection of 30deg, and sideslip angles of 0deg and -7.5deg. Greater than 20% increments in side force were achieved at the two sideslip angles with a 31-actuator AFC configuration. Flow physics and flow separation control associated with the AFC are presented in detail. AFC caused significant increases in suction pressure on the actuator side and associated side force enhancement. The momentum coefficient (C sub mu) is shown to be a useful parameter to use for scaling-up sweeping jet AFC from sub-scale tests to full-scale applications. Reducing the number of actuators at a constant total C(sub mu) of approximately 0.5% and tripling the actuator spacing did not significantly affect the flow separation control effectiveness.

Assessing health-related quality of life in Japanese children with a chronic condition: validation of the DISABKIDS chronic generic module.

PubMed

Sasaki, Hatoko; Kakee, Naoko; Morisaki, Naho; Mori, Rintaro; Ravens-Sieberer, Ulrike; Bullinger, Monika

2018-05-02

This study examined the reliability and validity of the Japanese versions of the DISABKIDS-37 generic modules, a tool for assessing the health-related quality of life (HRQOL) of children and adolescents with a chronic condition. The study was conducted using a sample of 123 children/adolescents with a chronic medical condition, aged 8-18 years, and their parents. Focus interviews were performed to ensure content validity after translation. The classical psychometric tests were used to assess reliability and scale intercorrelations. The factor structure was examined with confirmatory factor analysis (CFA). Convergent validity was assessed by the correlation between the total score and the sub-scales of DISABKIDS-37 as well as the total score of KIDSCREEN-10. Both the children/adolescent and parent versions of the score showed good to high internal consistency, and the test-retest reliability correlations were r = 0.91 or above. The CFA revealed that the modified models for all domains were better fit than the original 37 item scale model for both self-report and proxy-report. Moderate to high positive correlations were found for the associations within DISABKIDS-37 sub-scales and between the subscales and total score, except for the treatment sub-scale, which correlated weakly with the remaining sub-scales. The total score of the child-reported version of KIDSCREEN-10 correlated significantly and positively with the total score and all the sub-scales of the child-reported version of DISABKIDS-37 except the Treatment sub-scale in adolescents. The modified models of Japanese version of DISABKIDS generic module were psychometrically robust enough to assess the HRQOL of children with a chronic condition.

Uncovering three-dimensional gradients in fibrillar orientation in an impact-resistant biological armour.

PubMed

Zhang, Y; Paris, O; Terrill, N J; Gupta, H S

2016-05-23

The complex hierarchical structure in biological and synthetic fibrous nanocomposites entails considerable difficulties in the interpretation of the crystallographic texture from diffraction data. Here, we present a novel reconstruction method to obtain the 3D distribution of fibres in such systems. An analytical expression is derived for the diffraction intensity from fibres, explaining the azimuthal intensity distribution in terms of the angles of the three dimensional fibre orientation distributions. The telson of stomatopod (mantis shrimp) serves as an example of natural biological armour whose high impact resistance property is believed to arise from the hierarchical organization of alpha chitin nanofibrils into fibres and twisted plywood (Bouligand) structures at the sub-micron and micron scale. Synchrotron microfocus scanning X-ray diffraction data on stomatopod telson were used as a test case to map the 3D fibre orientation across the entire tissue section. The method is applicable to a range of biological and biomimetic structures with graded 3D fibre texture at the sub-micron and micron length scales.

Uncovering three-dimensional gradients in fibrillar orientation in an impact-resistant biological armour

NASA Astrophysics Data System (ADS)

Zhang, Y.; Paris, O.; Terrill, N. J.; Gupta, H. S.

2016-05-01

The complex hierarchical structure in biological and synthetic fibrous nanocomposites entails considerable difficulties in the interpretation of the crystallographic texture from diffraction data. Here, we present a novel reconstruction method to obtain the 3D distribution of fibres in such systems. An analytical expression is derived for the diffraction intensity from fibres, explaining the azimuthal intensity distribution in terms of the angles of the three dimensional fibre orientation distributions. The telson of stomatopod (mantis shrimp) serves as an example of natural biological armour whose high impact resistance property is believed to arise from the hierarchical organization of alpha chitin nanofibrils into fibres and twisted plywood (Bouligand) structures at the sub-micron and micron scale. Synchrotron microfocus scanning X-ray diffraction data on stomatopod telson were used as a test case to map the 3D fibre orientation across the entire tissue section. The method is applicable to a range of biological and biomimetic structures with graded 3D fibre texture at the sub-micron and micron length scales.

Uncovering three-dimensional gradients in fibrillar orientation in an impact-resistant biological armour

PubMed Central

Zhang, Y.; Paris, O.; Terrill, N. J.; Gupta, H. S.

2016-01-01

The complex hierarchical structure in biological and synthetic fibrous nanocomposites entails considerable difficulties in the interpretation of the crystallographic texture from diffraction data. Here, we present a novel reconstruction method to obtain the 3D distribution of fibres in such systems. An analytical expression is derived for the diffraction intensity from fibres, explaining the azimuthal intensity distribution in terms of the angles of the three dimensional fibre orientation distributions. The telson of stomatopod (mantis shrimp) serves as an example of natural biological armour whose high impact resistance property is believed to arise from the hierarchical organization of alpha chitin nanofibrils into fibres and twisted plywood (Bouligand) structures at the sub-micron and micron scale. Synchrotron microfocus scanning X-ray diffraction data on stomatopod telson were used as a test case to map the 3D fibre orientation across the entire tissue section. The method is applicable to a range of biological and biomimetic structures with graded 3D fibre texture at the sub-micron and micron length scales. PMID:27211574

Computation of indirect nuclear spin-spin couplings with reduced complexity in pure and hybrid density functional approximations.

PubMed

Luenser, Arne; Kussmann, Jörg; Ochsenfeld, Christian

2016-09-28

We present a (sub)linear-scaling algorithm to determine indirect nuclear spin-spin coupling constants at the Hartree-Fock and Kohn-Sham density functional levels of theory. Employing efficient integral algorithms and sparse algebra routines, an overall (sub)linear scaling behavior can be obtained for systems with a non-vanishing HOMO-LUMO gap. Calculations on systems with over 1000 atoms and 20 000 basis functions illustrate the performance and accuracy of our reference implementation. Specifically, we demonstrate that linear algebra dominates the runtime of conventional algorithms for 10 000 basis functions and above. Attainable speedups of our method exceed 6 × in total runtime and 10 × in the linear algebra steps for the tested systems. Furthermore, a convergence study of spin-spin couplings of an aminopyrazole peptide upon inclusion of the water environment is presented: using the new method it is shown that large solvent spheres are necessary to converge spin-spin coupling values.

Thermo-Oxidization of Municipal Wastewater Treatment Plant Sludge for Production of Class A Biosolids

EPA Science Inventory

Bench-scale reactors were used to test a novel thermo-oxidation process on municipal wastewater treatment plant (WWTP) waste activated sludge (WAS) using hydrogen peroxide (H₂O₂) to achieve a Class A sludge product appropriate for land application. Reactor ...

Method of immobilizing weapons plutonium to provide a durable, disposable waste product

DOEpatents

Ewing, Rodney C.; Lutze, Werner; Weber, William J.

1996-01-01

A method of atomic scale fixation and immobilization of plutonium to provide a durable waste product. Plutonium is provided in the form of either PuO.sub.2 or Pu(NO.sub.3).sub.4 and is mixed with and SiO.sub.2. The resulting mixture is cold pressed and then heated under pressure to form (Zr,Pu)SiO.sub.4 as the waste product.

Radiation Test Challenges for Scaled Commerical Memories

NASA Technical Reports Server (NTRS)

LaBel, Kenneth A.; Ladbury, Ray L.; Cohn, Lewis M.; Oldham, Timothy

2007-01-01

As sub-100nm CMOS technologies gather interest, the radiation effects performance of these technologies provide a significant challenge. In this talk, we shall discuss the radiation testing challenges as related to commercial memory devices. The focus will be on complex test and failure modes emerging in state-of-the-art Flash non-volatile memories (NVMs) and synchronous dynamic random access memories (SDRAMs), which are volatile. Due to their very high bit density, these device types are highly desirable for use in the natural space environment. In this presentation, we shall discuss these devices with emphasis on considerations for test and qualification methods required.

Fabrication and characterization of millimeter-scale translucent La{sub 2}O{sub 3}-doped Al{sub 2}O{sub 3} ceramic hollow spheres

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Haoting; Liao, Qilong, E-mail: liaoqilong@swust.edu.cn; Dai, Yunya

2016-04-15

Highlights: • Millimeter-scale translucent La{sub 2}O{sub 3}-doped Al{sub 2}O{sub 3} hollow spheres have been prepared. • The diameters of the prepared hollow spheres are 500–1300μm. • The degree of sphericity for the prepared hollow spheres is above 98%. • The mechanisms of transparency are discussed. - Abstract: Millimeter-scale translucent La{sub 2}O{sub 3}-doped Al{sub 2}O{sub 3} ceramic hollow spheres have been successfully prepared using the oil-in-water (paraffin-in-alumina sol) droplets as precursors made by self-made T-shape micro-emulsion device. The main crystalline phase of the obtained hollow sphere is alpha alumina. The prepared translucent La{sub 2}O{sub 3}-containing Al{sub 2}O{sub 3} ceramic hollow spheresmore » have diameters of 500–1300 μm, wall thickness of about 23 μm and the degree of sphericity of above 98%. With the increase of the La{sub 2}O{sub 3} content, grains and grain-boundaries of the alumina spherical shell for the prepared millimeter-scale hollow spheres become regular and clear gradually. When the La{sub 2}O{sub 3} content is 0.1 wt.%, the crystal surface of the obtained Al{sub 2}O{sub 3} spherical shell shows optimal grains and few pores, and its transmittance reaches 42% at 532 nm laser light. This method provides a promising technique of preparing millimeter-scale translucent ceramic hollow spheres for laser inertial confined fusion.« less

Development of the Stress of Immigration Survey (SOIS): a Field Test among Mexican Immigrant Women

PubMed Central

Sternberg, Rosa Maria; Nápoles, Anna Maria; Gregorich, Steven; Paul, Steven; Lee, Kathryn A.; Stewart, Anita L.

2016-01-01

The Stress of Immigration Survey (SOIS) is a screening tool used to assess immigration-related stress. The mixed methods approach included concept development, pretesting, field-testing, and psychometric evaluation in a sample of 131 low-income women of Mexican descent. The 21-item SOIS screens for stress related to language; immigrant status; work issues; yearning for family and home country; and cultural dissonance. Mean scores ranged from 3.6 to 4.4 (1-5 scale, higher is more stress). Cronbach's alphas >.80 for all sub-scales. The SOIS may be a useful screening tool for detecting high levels of immigration-related stress in low-income Mexican immigrant women. PMID:26605954

A short version of the revised 'experience of close relationships questionnaire': investigating non-clinical and clinical samples.

PubMed

Wongpakaran, Tinakon; Wongpakaran, Nahathai

2012-01-01

This study seeks to investigate the psychometric properties of the short version of the revised 'Experience of Close Relationships' questionnaire, comparing non-clinical and clinical samples. In total 702 subjects participated in this study, of whom 531 were non-clinical participants and 171 were psychiatric patients. They completed the short version of the revised 'Experience of Close Relationships' questionnaire (ECR-R-18), the Perceived Stress Scale-10(PSS-10), the Rosenberg Self-Esteem Scale (RSES) and the UCLA Loneliness scale. A retest of the ECR-R-18 was then performed at four-week intervals. Then, confirmatory factor analyses were performed to test the validity of the new scale. The ECR-R-18 showed a fair to good internal consistency (α 0.77 to 0.87) for both samples, and the test-retest reliability was found to be satisfactory (ICC = 0.75). The anxiety sub-scale demonstrated concurrent validity with PSS-10 and RSES, while the avoidance sub-scale showed concurrent validity with the UCLA Loneliness Scale. Confirmatory factor analysis using method factors yielded two factors with an acceptable model fit for both groups. An invariance test revealed that the ECR-R-18 when used on the clinical group differed from when used with the non-clinical group. The ECR-R-18 questionnaire revealed an overall better level of fit than the original 36 item questionnaire, indicating its suitability for use with a broader group of samples, including clinical samples. The reliability of the ECR-R- 18 might be increased if a modified scoring system is used and if our suggestions with regard to future studies are followed up.

Full-Scale Turbofan Engine Noise-Source Separation Using a Four-Signal Method

NASA Technical Reports Server (NTRS)

Hultgren, Lennart S.; Arechiga, Rene O.

2016-01-01

Contributions from the combustor to the overall propulsion noise of civilian transport aircraft are starting to become important due to turbofan design trends and expected advances in mitigation of other noise sources. During on-ground, static-engine acoustic tests, combustor noise is generally sub-dominant to other engine noise sources because of the absence of in-flight effects. Consequently, noise-source separation techniques are needed to extract combustor-noise information from the total noise signature in order to further progress. A novel four-signal source-separation method is applied to data from a static, full-scale engine test and compared to previous methods. The new method is, in a sense, a combination of two- and three-signal techniques and represents an attempt to alleviate some of the weaknesses of each of those approaches. This work is supported by the NASA Advanced Air Vehicles Program, Advanced Air Transport Technology Project, Aircraft Noise Reduction Subproject and the NASA Glenn Faculty Fellowship Program.

Applying the global RCP-SSP-SPA scenario framework at sub-national scale: A multi-scale and participatory scenario approach.

PubMed

Kebede, Abiy S; Nicholls, Robert J; Allan, Andrew; Arto, Iñaki; Cazcarro, Ignacio; Fernandes, Jose A; Hill, Chris T; Hutton, Craig W; Kay, Susan; Lázár, Attila N; Macadam, Ian; Palmer, Matthew; Suckall, Natalie; Tompkins, Emma L; Vincent, Katharine; Whitehead, Paul W

2018-09-01

To better anticipate potential impacts of climate change, diverse information about the future is required, including climate, society and economy, and adaptation and mitigation. To address this need, a global RCP (Representative Concentration Pathways), SSP (Shared Socio-economic Pathways), and SPA (Shared climate Policy Assumptions) (RCP-SSP-SPA) scenario framework has been developed by the Intergovernmental Panel on Climate Change Fifth Assessment Report (IPCC-AR5). Application of this full global framework at sub-national scales introduces two key challenges: added complexity in capturing the multiple dimensions of change, and issues of scale. Perhaps for this reason, there are few such applications of this new framework. Here, we present an integrated multi-scale hybrid scenario approach that combines both expert-based and participatory methods. The framework has been developed and applied within the DECCMA 1 project with the purpose of exploring migration and adaptation in three deltas across West Africa and South Asia: (i) the Volta delta (Ghana), (ii) the Mahanadi delta (India), and (iii) the Ganges-Brahmaputra-Meghna (GBM) delta (Bangladesh/India). Using a climate scenario that encompasses a wide range of impacts (RCP8.5) combined with three SSP-based socio-economic scenarios (SSP2, SSP3, SSP5), we generate highly divergent and challenging scenario contexts across multiple scales against which robustness of the human and natural systems within the deltas are tested. In addition, we consider four distinct adaptation policy trajectories: Minimum intervention, Economic capacity expansion, System efficiency enhancement, and System restructuring, which describe alternative future bundles of adaptation actions/measures under different socio-economic trajectories. The paper highlights the importance of multi-scale (combined top-down and bottom-up) and participatory (joint expert-stakeholder) scenario methods for addressing uncertainty in adaptation decision-making. The framework facilitates improved integrated assessments of the potential impacts and plausible adaptation policy choices (including migration) under uncertain future changing conditions. The concept, methods, and processes presented are transferable to other sub-national socio-ecological settings with multi-scale challenges. Copyright © 2018. Published by Elsevier B.V.

Family and peer support matter for precoital and coital behaviors among adolescents in Lima

PubMed Central

Bayer, Angela M.; Cabrera, Lilia Z.; Gilman, Robert H.; Hindin, Michelle J.; Tsui, Amy O.

2015-01-01

We analyzed the association between sub-scales developed with adolescents and the outcomes of precoital behaviors and vaginal sex in Lima, Peru. Adolescent participants in key informant sessions operationalized concepts identified during qualitative concept mapping into several sub-scales. Face and content validity testing and pilot application with respondent debriefing were used to refine the sub-scales. Three hundred 15–17 year olds were surveyed about the sub-scales, socio-demographics and sexual behaviors. Exploratory factor analysis confirmed six sub-scales, self-image, goals and decision-making, family education, parental rules/control, school support and peer support, which we regressed on the outcomes. Twice as many males as females reported more than three precoital behaviors and vaginal sex. Higher peer support reduced the likelihood of vaginal sex and precoital behaviors and higher family education reduced precoital behaviors. Results affirm the importance of including adolescents in the entire research process and of sex education with family- and peer-based strategies. PMID:25305443

Isometric scaling of above- and below-ground biomass at the individual and community levels in the understorey of a sub-tropical forest

PubMed Central

Cheng, Dongliang; Zhong, Quanlin; Niklas, Karl J.; Ma, Yuzhu; Yang, Yusheng; Zhang, Jianhua

2015-01-01

Background and Aims Empirical studies and allometric partitioning (AP) theory indicate that plant above-ground biomass (MA) scales, on average, one-to-one (isometrically) with below-ground biomass (MR) at the level of individual trees and at the level of entire forest communities. However, the ability of the AP theory to predict the biomass allocation patterns of understorey plants has not been established because most previous empirical tests have focused on canopy tree species or very large shrubs. Methods In order to test the AP theory further, 1586 understorey sub-tropical forest plants from 30 sites in south-east China were harvested and examined. The numerical values of the scaling exponents and normalization constants (i.e. slopes and y-intercepts, respectively) of log–log linear MA vs. MR relationships were determined for all individual plants, for each site, across the entire data set, and for data sorted into a total of 19 sub-sets of forest types and successional stages. Similar comparisons of MA/MR were also made. Key Results The data revealed that the mean MA/MR of understorey plants was 2·44 and 1·57 across all 1586 plants and for all communities, respectively, and MA scaled nearly isometrically with respect to MR, with scaling exponents of 1·01 for all individual plants and 0·99 for all communities. The scaling exponents did not differ significantly among different forest types or successional stages, but the normalization constants did, and were positively correlated with MA/MR and negatively correlated with scaling exponents across all 1586 plants. Conclusions The results support the AP theory’s prediction that MA scales nearly one-to-one with MR (i.e. MA ∝ MR ≈1·0) and that plant biomass partitioning for individual plants and at the community level share a strikingly similar pattern, at least for the understorey plants examined in this study. Furthermore, variation in environmental conditions appears to affect the numerical values of normalization constants, but not the scaling exponents of the MA vs. MR relationship. This feature of the results suggests that plant size is the primary driver of the MA vs. MR biomass allocation pattern for understorey plants in sub-tropical forests. PMID:25564468

Development of Flight-Test Performance Estimation Techniques for Small Unmanned Aerial Systems

NASA Astrophysics Data System (ADS)

McCrink, Matthew Henry

This dissertation provides a flight-testing framework for assessing the performance of fixed-wing, small-scale unmanned aerial systems (sUAS) by leveraging sub-system models of components unique to these vehicles. The development of the sub-system models, and their links to broader impacts on sUAS performance, is the key contribution of this work. The sub-system modeling and analysis focuses on the vehicle's propulsion, navigation and guidance, and airframe components. Quantification of the uncertainty in the vehicle's power available and control states is essential for assessing the validity of both the methods and results obtained from flight-tests. Therefore, detailed propulsion and navigation system analyses are presented to validate the flight testing methodology. Propulsion system analysis required the development of an analytic model of the propeller in order to predict the power available over a range of flight conditions. The model is based on the blade element momentum (BEM) method. Additional corrections are added to the basic model in order to capture the Reynolds-dependent scale effects unique to sUAS. The model was experimentally validated using a ground based testing apparatus. The BEM predictions and experimental analysis allow for a parameterized model relating the electrical power, measurable during flight, to the power available required for vehicle performance analysis. Navigation system details are presented with a specific focus on the sensors used for state estimation, and the resulting uncertainty in vehicle state. Uncertainty quantification is provided by detailed calibration techniques validated using quasi-static and hardware-in-the-loop (HIL) ground based testing. The HIL methods introduced use a soft real-time flight simulator to provide inertial quality data for assessing overall system performance. Using this tool, the uncertainty in vehicle state estimation based on a range of sensors, and vehicle operational environments is presented. The propulsion and navigation system models are used to evaluate flight-testing methods for evaluating fixed-wing sUAS performance. A brief airframe analysis is presented to provide a foundation for assessing the efficacy of the flight-test methods. The flight-testing presented in this work is focused on validating the aircraft drag polar, zero-lift drag coefficient, and span efficiency factor. Three methods are detailed and evaluated for estimating these design parameters. Specific focus is placed on the influence of propulsion and navigation system uncertainty on the resulting performance data. Performance estimates are used in conjunction with the propulsion model to estimate the impact sensor and measurement uncertainty on the endurance and range of a fixed-wing sUAS. Endurance and range results for a simplistic power available model are compared to the Reynolds-dependent model presented in this work. Additional parameter sensitivity analysis related to state estimation uncertainties encountered in flight-testing are presented. Results from these analyses indicate that the sub-system models introduced in this work are of first-order importance, on the order of 5-10% change in range and endurance, in assessing the performance of a fixed-wing sUAS.

SU-E-T-271: Direct Measurement of Tenth Value Layer Thicknesses for High Density Concretes with a Clinical Machine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tanny, S; Parsai, E; Harrell, D

2015-06-15

Purpose: Use of high density concrete for radiation shielding is increasing, trading cost for space savings associated with the reduced tenth value layer (TVL). Precise information on the attenuation properties of high-density concretes is not readily present in the literature. A simple approximation is to scale the TVLs from NCRP 151 according relative increase in density. Here we present measured TVLs for heavy concretes of various densities using a built-in shielding test port. Methods: Concrete densities tested range from 2.35 g cc{sup −1} (147 pcf) to 5.6 g cc{sup −1} (350 pcf). Measurements were taken using 6MV, 6FFF, and 10FFFmore » on a Varian Truebeam linear accelerator. Field sizes of 4x4, 9x9 and 30x30 cm{sup 2} were measured. A PTW 31013 Farmer chamber with a buildup cap was positioned 5.5 m from isocenter along the beam CAX. Concrete thicknesses were incremented in 5 cm intervals. Comparison TVLs were determined by scaling the NCRP 151 TVLs by the density ratio between the sample and standard density. Results: The trend from the first to equilibrium TVL was an increase in thickness, compared with MC modeling, which predicted a decrease. Measured TVLs for 6 MV were reduced by as much as 8.9 cm for TVL{sub 1} and 3.4 cm for TVL{sub E} compared to values scaled from NCRP 151. There was 1–3 mm difference in TVL between measurements done at 4x4 versus 30x30 cm{sup 2}. TVL{sub 1} for 6FFF was 1.1 cm smaller than TVL{sub 1} for 6MV, but TVL{sub E} was consistent to within 4 mm. TVL{sub 1} and TVL{sub E} for 10FFF were reduced by 8.8 and 3.7 cm from scaled NCRP values, respectively. Conclusions: We have measured the TVL thicknesses for various concretes. Simple density scaling of the values in NCRP 151 is a conservatively safe approximation, but actual TVLs may be reduced enough to eliminate some of the expense of installation. Daniel Harrell and Jim Noller are employees of Shielding Construction Solutions, Inc, the shielding construction company that built the vault discussed in this abstract. Manjit Chopra is an employee of Universal Minerals International, Inc, the company that provided the aggregates for the high density concretes used in the vault construction.« less

Model Uncertainty Quantification Methods For Data Assimilation In Partially Observed Multi-Scale Systems

NASA Astrophysics Data System (ADS)

Pathiraja, S. D.; van Leeuwen, P. J.

2017-12-01

Model Uncertainty Quantification remains one of the central challenges of effective Data Assimilation (DA) in complex partially observed non-linear systems. Stochastic parameterization methods have been proposed in recent years as a means of capturing the uncertainty associated with unresolved sub-grid scale processes. Such approaches generally require some knowledge of the true sub-grid scale process or rely on full observations of the larger scale resolved process. We present a methodology for estimating the statistics of sub-grid scale processes using only partial observations of the resolved process. It finds model error realisations over a training period by minimizing their conditional variance, constrained by available observations. Special is that these realisations are binned conditioned on the previous model state during the minimization process, allowing for the recovery of complex error structures. The efficacy of the approach is demonstrated through numerical experiments on the multi-scale Lorenz 96' model. We consider different parameterizations of the model with both small and large time scale separations between slow and fast variables. Results are compared to two existing methods for accounting for model uncertainty in DA and shown to provide improved analyses and forecasts.

Reliability and validity of Short Form 36 Version 2 to measure health perceptions in a sub-group of individuals with fatigue.

PubMed

Davenport, Todd E; Stevens, Staci R; Baroni, Katie; Van Ness, J Mark; Snell, Christopher R

2011-01-01

To determine the validity and reliability of Short Form 36 Version 2 (SF36v2) in sub-groups of individuals with fatigue. Thirty subjects participated in this study, including n = 16 subjects who met case definition criteria for chronic fatigue syndrome (CFS) and n = 14 non-disabled sedentary matched control subjects. SF36v2 and Multidimensional Fatigue Inventory (MFI-20) were administered before two maximal cardiopulmonary exercise tests (CPETs) administered 24 h apart and an open-ended recovery questionnaire was administered 7 days after CPET challenge. The main outcome measures were self-reported time to recover to pre-challenge functional and symptom status, frequency of post-exertional symptoms and SF36v2 sub-scale scores. Individuals with CFS demonstrated significantly lower SF36v2 and MFI-20 sub-scale scores prior to CPET. Between-group differences remained significant post-CPET, however, there were no significant group by test interaction effects. Subjects with CFS reported significantly more total symptoms (p < 0.001), as well as reports of fatigue (p < 0.001), neuroendocrine (p < 0.001), immune (p < 0.01), pain (p < 0.01) and sleep disturbance (p < 0.01) symptoms than control subjects as a result of CPET. Many symptom counts demonstrated significant relationships with SF36v2 sub-scale scores (p < 0.05). SF36v2 and MFI-20 sub-scale scores demonstrated significant correlations (p < 0.05). Various SF36v2 sub-scale scores demonstrated significant predictive validity to identify subjects who recovered from CPET challenge within 1 day and 7 days (p < 0.05). Potential floor effects were observed for both questionnaires for individuals with CFS. Various sub-scales of SF36v2 demonstrated adequate reliability and validity for clinical and research applications. Adequacy of sensitivity to change of SF36v2 as a result of a fatiguing stressor should be the subject of additional study.

A depth-first search algorithm to compute elementary flux modes by linear programming

PubMed Central

2014-01-01

Background The decomposition of complex metabolic networks into elementary flux modes (EFMs) provides a useful framework for exploring reaction interactions systematically. Generating a complete set of EFMs for large-scale models, however, is near impossible. Even for moderately-sized models (<400 reactions), existing approaches based on the Double Description method must iterate through a large number of combinatorial candidates, thus imposing an immense processor and memory demand. Results Based on an alternative elementarity test, we developed a depth-first search algorithm using linear programming (LP) to enumerate EFMs in an exhaustive fashion. Constraints can be introduced to directly generate a subset of EFMs satisfying the set of constraints. The depth-first search algorithm has a constant memory overhead. Using flux constraints, a large LP problem can be massively divided and parallelized into independent sub-jobs for deployment into computing clusters. Since the sub-jobs do not overlap, the approach scales to utilize all available computing nodes with minimal coordination overhead or memory limitations. Conclusions The speed of the algorithm was comparable to efmtool, a mainstream Double Description method, when enumerating all EFMs; the attrition power gained from performing flux feasibility tests offsets the increased computational demand of running an LP solver. Unlike the Double Description method, the algorithm enables accelerated enumeration of all EFMs satisfying a set of constraints. PMID:25074068

Exploring cosmic homogeneity with the BOSS DR12 galaxy sample

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ntelis, Pierros; Hamilton, Jean-Christophe; Busca, Nicolas Guillermo

2017-06-01

In this study, we probe the transition to cosmic homogeneity in the Large Scale Structure (LSS) of the Universe using the CMASS galaxy sample of BOSS spectroscopic survey which covers the largest effective volume to date, 3 h {sup −3} Gpc{sup 3} at 0.43 ≤ z ≤ 0.7. We study the scaled counts-in-spheres, N(< r ), and the fractal correlation dimension, D{sub 2}( r ), to assess the homogeneity scale of the universe using a Landy and Szalay inspired estimator. Defining the scale of transition to homogeneity as the scale at which D{sub 2}( r ) reaches 3 within 1%,more » i.e. D{sub 2}( r )>2.97 for r >R {sub H} , we find R {sub H} = (63.3±0.7) h {sup −1} Mpc, in agreement at the percentage level with the predictions of the ΛCDM model R {sub H} =62.0 h {sup −1} Mpc. Thanks to the large cosmic depth of the survey, we investigate the redshift evolution of the transition to homogeneity scale and find agreement with the ΛCDM prediction. Finally, we find that D{sub 2} is compatible with 3 at scales larger than 300 h {sup −1} Mpc in all redshift bins. These results consolidate the Cosmological Principle and represent a precise consistency test of the ΛCDM model.« less

Enabling UAS Research at the NASA EAV Laboratory

NASA Technical Reports Server (NTRS)

Ippolito, Corey A.

2015-01-01

The Exploration Aerial Vehicles (EAV) Laboratory at NASA Ames Research Center leads research into intelligent autonomy and advanced control systems, bridging the gap between simulation and full-scale technology through flight test experimentation on unmanned sub-scale test vehicles.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gonzalez, J.E.; Alcaniz, J.S.; Carvalho, J.C., E-mail: javierernesto@on.br, E-mail: alcaniz@on.br, E-mail: jcarvalho@on.br

The existing degeneracy between different dark energy and modified gravity cosmologies at the background level may be broken by analyzing quantities at the perturbative level. In this work, we apply a non-parametric smoothing (NPS) method to reconstruct the expansion history of the Universe ( H ( z )) from model-independent cosmic chronometers and high- z quasar data. Assuming a homogeneous and isotropic flat universe and general relativity (GR) as the gravity theory, we calculate the non-relativistic matter perturbations in the linear regime using the H ( z ) reconstruction and realistic values of Ω {sub m} {sub 0} and σ{submore » 8} from Planck and WMAP-9 collaborations. We find a good agreement between the measurements of the growth rate and f σ{sub 8}( z ) from current large-scale structure observations and the estimates obtained from the reconstruction of the cosmic expansion history. Considering a recently proposed null test for GR using matter perturbations, we also apply the NPS method to reconstruct f σ{sub 8}( z ). For this case, we find a ∼ 3σ tension (good agreement) with the standard relativistic cosmology when the Planck (WMAP-9) priors are used.« less

Land cover mapping at sub-pixel scales

NASA Astrophysics Data System (ADS)

Makido, Yasuyo Kato

One of the biggest drawbacks of land cover mapping from remotely sensed images relates to spatial resolution, which determines the level of spatial details depicted in an image. Fine spatial resolution images from satellite sensors such as IKONOS and QuickBird are now available. However, these images are not suitable for large-area studies, since a single image is very small and therefore it is costly for large area studies. Much research has focused on attempting to extract land cover types at sub-pixel scale, and little research has been conducted concerning the spatial allocation of land cover types within a pixel. This study is devoted to the development of new algorithms for predicting land cover distribution using remote sensory imagery at sub-pixel level. The "pixel-swapping" optimization algorithm, which was proposed by Atkinson for predicting sub-pixel land cover distribution, is investigated in this study. Two limitations of this method, the arbitrary spatial range value and the arbitrary exponential model of spatial autocorrelation, are assessed. Various weighting functions, as alternatives to the exponential model, are evaluated in order to derive the optimum weighting function. Two different simulation models were employed to develop spatially autocorrelated binary class maps. In all tested models, Gaussian, Exponential, and IDW, the pixel swapping method improved classification accuracy compared with the initial random allocation of sub-pixels. However the results suggested that equal weight could be used to increase accuracy and sub-pixel spatial autocorrelation instead of using these more complex models of spatial structure. New algorithms for modeling the spatial distribution of multiple land cover classes at sub-pixel scales are developed and evaluated. Three methods are examined: sequential categorical swapping, simultaneous categorical swapping, and simulated annealing. These three methods are applied to classified Landsat ETM+ data that has been resampled to 210 meters. The result suggested that the simultaneous method can be considered as the optimum method in terms of accuracy performance and computation time. The case study employs remote sensing imagery at the following sites: tropical forests in Brazil and temperate multiple land mosaic in East China. Sub-areas for both sites are used to examine how the characteristics of the landscape affect the ability of the optimum technique. Three types of measurement: Moran's I, mean patch size (MPS), and patch size standard deviation (STDEV), are used to characterize the landscape. All results suggested that this technique could increase the classification accuracy more than traditional hard classification. The methods developed in this study can benefit researchers who employ coarse remote sensing imagery but are interested in detailed landscape information. In many cases, the satellite sensor that provides large spatial coverage has insufficient spatial detail to identify landscape patterns. Application of the super-resolution technique described in this dissertation could potentially solve this problem by providing detailed land cover predictions from the coarse resolution satellite sensor imagery.

Static Aeroelastic Scaling and Analysis of a Sub-Scale Flexible Wing Wind Tunnel Model

NASA Technical Reports Server (NTRS)

Ting, Eric; Lebofsky, Sonia; Nguyen, Nhan; Trinh, Khanh

2014-01-01

This paper presents an approach to the development of a scaled wind tunnel model for static aeroelastic similarity with a full-scale wing model. The full-scale aircraft model is based on the NASA Generic Transport Model (GTM) with flexible wing structures referred to as the Elastically Shaped Aircraft Concept (ESAC). The baseline stiffness of the ESAC wing represents a conventionally stiff wing model. Static aeroelastic scaling is conducted on the stiff wing configuration to develop the wind tunnel model, but additional tailoring is also conducted such that the wind tunnel model achieves a 10% wing tip deflection at the wind tunnel test condition. An aeroelastic scaling procedure and analysis is conducted, and a sub-scale flexible wind tunnel model based on the full-scale's undeformed jig-shape is developed. Optimization of the flexible wind tunnel model's undeflected twist along the span, or pre-twist or wash-out, is then conducted for the design test condition. The resulting wind tunnel model is an aeroelastic model designed for the wind tunnel test condition.

Purification and preparation of graphite oxide from natural graphite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Panatarani, C., E-mail: c.panatarani@phys.unpad.ac.id; Muthahhari, N.; Joni, I. Made

2016-03-11

Graphite oxide has attracted much interest as a possible route for preparation of natural graphite in the large-scale production and manipulation of graphene as a material with extraordinary electronic properties. Graphite oxide was prepared by modified Hummers method from purified natural graphite sample from West Kalimantan. We demonstrated that natural graphite is well-purified by acid leaching method. The purified graphite was proceed for intercalating process by modifying Hummers method. The modification is on the reaction time and temperature of the intercalation process. The materials used in the intercalating process are H{sub 2}SO{sub 4} and KMNO{sub 4}. The purified natural graphitemore » is analyzed by carbon content based on Loss on Ignition test. The thermo gravimetricanalysis and the Fouriertransform infrared spectroscopy are performed to investigate the oxidation results of the obtained GO which is indicated by the existence of functional groups. In addition, the X-ray diffraction and energy dispersive X-ray spectroscopy are also applied to characterize respectively for the crystal structure and elemental analysis. The results confirmed that natural graphite samples with 68% carbon content was purified into 97.68 % carbon content. While the intercalation process formed a formation of functional groups in the obtained GO. The results show that the temperature and reaction times have improved the efficiency of the oxidation process. It is concluded that these method could be considered as an important route for large-scale production of graphene.« less

Experimental investigation of 150-KG-scale corium melt jet quenching in water

DOE Office of Scientific and Technical Information (OSTI.GOV)

Magallon, D.; Hohmann, H.

This paper compares and discusses the results of two large scale FARO quenching tests known as L-11 and L-14, which involved, respectively, 151 kg of W% 76.7 UO{sub 2} + 19.2 ZrO{sub 2} + 4.1 Zr and 125 kg of W% 80 UO{sub 2} + 20 ZrO{sub 2} melts poured into 600-kg, 2-m-depth water at saturation at 5.0 MPa. The results are further compared with those of two previous tests performed using a pure oxidic melt, respectively 18 and 44 kg of W% 80 UO{sub 2} + 20 ZrO{sub 2} melt quenched in 1-m-depth water at saturation at 5.0 MPa.more » In all the tests, significant breakup and quenching took place during the melt fall through the water. No steam explosion occurred. In the tests performed with a pure oxide UO{sub 2}-ZrO{sub 2} melt, part of the corium (from 1/6 to 1/3) did not breakup and reached the bottom plate still molten whatever the water depth was. Test L-11 data suggest that full oxidation and complete breakup of the melt occurred during the melt fall through the water. A proportion of 64% of the total energy content of the melt was released to the water during this phase ({approximately}1.5 s), against 44% for L-14. The maximum temperature increase of the bottom plate was 330 K (L-14). The mean particle size of the debris ranged between 2.5 and 4.8mm.« less

Experimental method for determination of bending and torsional rigidities of advanced composite laminates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maeda, Takenori

1995-11-01

This paper presents an experimental method for the determination of the bending and torsional rigidities of advanced fiber composite laminates with the aid of laser holographic interferometry. The proposed method consists of a four-point bending test and a resonance test. The bending rigidity ratio (D{sub 12}/D{sub 22}) can be determined from the fringe patterns of the four-point bending test. The bending rigidities (D{sub 11} and D{sub 22}) and the torsional rigidity (D{sub 66}) are calculated from the natural frequencies of cantilever plates of the resonance test. The test specimens are carbon/epoxy cross-ply laminates. The adequacy of the experimental method ismore » confirmed by comparing the measured rigidities with the theoretical values obtained from classical lamination theory (CLT) by using the measured tensile properties. The results show that the present method can be used to evaluate the rigidities of orthotropic laminates with reasonably good accuracy.« less

Semi-Technical Cryogenic Molecular Sieve Bed for the Tritium Extraction System of the Test Blanket Module for ITER

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beloglazov, S.; Bekris, N.; Glugla, M.

2005-07-15

The tritium extraction from the ITER Helium Cooled Pebble Bed (HCPB) Test Blanket Module purge gas is proposed to be performed in a two steps process: trapping water in a cryogenic Cold Trap, and adsorption of hydrogen isotopes (H{sub 2}, HT, T{sub 2}) as well as impurities (N{sub 2}, O{sub 2}) in a Cryogenic Molecular Sieve Bed (CMSB) at 77K. A CMSB in a semi-technical scale (one-sixth of the flow rate of the ITER-HCPB) was design and constructed at the Forschungszentrum Karlsruhe. The full capacity of CMSB filled with 20 kg of MS-5A was calculated based on adsorption isotherm datamore » to be 9.4 mol of H{sub 2} at partial pressure 120 Pa. The breakthrough tests at flow rates up to 2 Nm{sup 3}h{sup -1} of He with 110 Pa of H{sub 2} conformed with good agreement the adsorption capacity of the CMSB. The mass-transfer zone was found to be relatively narrow (12.5 % of the MS Bed height) allowing to scale up the CMSB to ITER flow rates.« less

Sub-Scale Orion Parachute Test Results from the National Full-Scale Aerodynamics Complex 80- By 120-ft Wind Tunnel

NASA Technical Reports Server (NTRS)

Anderson, Brian P.; Greathouse, James S.; Powell, Jessica M.; Ross, James C.; Schairer, Edward T.; Kushner, Laura; Porter, Barry J.; Goulding, Patrick W., II; Zwicker, Matthew L.; Mollmann, Catherine

2017-01-01

A two-week test campaign was conducted in the National Full-Scale Aerodynamics Complex 80 x 120-ft Wind Tunnel in support of Orion parachute pendulum mitigation activities. The test gathered static aerodynamic data using an instrumented, 3-tether system attached to the parachute vent in combination with an instrumented parachute riser. Dynamic data was also gathered by releasing the tether system and measuring canopy performance using photogrammetry. Several canopy configurations were tested and compared against the current Orion parachute design to understand changes in drag performance and aerodynamic stability. These configurations included canopies with varying levels and locations of geometric porosity as well as sails with increased levels of fullness. In total, 37 runs were completed for a total of 392 data points. Immediately after the end of the testing campaign a down-select decision was made based on preliminary data to support follow-on sub-scale air drop testing. A summary of a more rigorous analysis of the test data is also presented.

[Silhouette scales and body satisfaction in adolescents: a systematic literature review].

PubMed

Côrtes, Marcela Guimarães; Meireles, Adriana Lúcia; Friche, Amélia Augusta de Lima; Caiaffa, Waleska Teixeira; Xavier, César Coelho

2013-03-01

The purpose of this study was to summarize studies on adolescents' body satisfaction, focusing on the use of silhouette scales. A systematic review was carried out on MEDLINE, LILACS, SciELO, and in unpublished papers. The final analysis included 36 studies. The majority adopted the scale proposed by Stunkard et al., self-administered, presented in ascending order and on a single sheet of paper. Most studies compared characteristics on satisfaction and dissatisfaction, used the chi-square test, and did not test for confounding. Among 18 studies included in the meta-analysis, prevalence of body dissatisfaction ranged from 32.2% to 83%. The review showed wide heterogeneity between studies (p-value = 0.000; I(2) = 87.39) even after sub-group analysis and the absence of relevant information for proper comparison of studies. The article concludes by recommending greater rigor in application of the scales and presentation of study methods on body satisfaction assessed by silhouette scales, in addition to new methodological studies and those that elucidate factors related to body satisfaction.

High capacity immobilized amine sorbents

DOEpatents

Gray, McMahan L [Pittsburgh, PA; Champagne, Kenneth J [Fredericktown, PA; Soong, Yee [Monroeville, PA; Filburn, Thomas [Granby, CT

2007-10-30

A method is provided for making low-cost CO.sub.2 sorbents that can be used in large-scale gas-solid processes. The improved method entails treating an amine to increase the number of secondary amine groups and impregnating the amine in a porous solid support. The method increases the CO.sub.2 capture capacity and decreases the cost of utilizing an amine-enriched solid sorbent in CO.sub.2 capture systems.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu Xiaoying; Ho, Shirley; Trac, Hy

We investigate machine learning (ML) techniques for predicting the number of galaxies (N{sub gal}) that occupy a halo, given the halo's properties. These types of mappings are crucial for constructing the mock galaxy catalogs necessary for analyses of large-scale structure. The ML techniques proposed here distinguish themselves from traditional halo occupation distribution (HOD) modeling as they do not assume a prescribed relationship between halo properties and N{sub gal}. In addition, our ML approaches are only dependent on parent halo properties (like HOD methods), which are advantageous over subhalo-based approaches as identifying subhalos correctly is difficult. We test two algorithms: supportmore » vector machines (SVM) and k-nearest-neighbor (kNN) regression. We take galaxies and halos from the Millennium simulation and predict N{sub gal} by training our algorithms on the following six halo properties: number of particles, M{sub 200}, {sigma}{sub v}, v{sub max}, half-mass radius, and spin. For Millennium, our predicted N{sub gal} values have a mean-squared error (MSE) of {approx}0.16 for both SVM and kNN. Our predictions match the overall distribution of halos reasonably well and the galaxy correlation function at large scales to {approx}5%-10%. In addition, we demonstrate a feature selection algorithm to isolate the halo parameters that are most predictive, a useful technique for understanding the mapping between halo properties and N{sub gal}. Lastly, we investigate these ML-based approaches in making mock catalogs for different galaxy subpopulations (e.g., blue, red, high M{sub star}, low M{sub star}). Given its non-parametric nature as well as its powerful predictive and feature selection capabilities, ML offers an interesting alternative for creating mock catalogs.« less

Coupled numerical approach combining finite volume and lattice Boltzmann methods for multi-scale multi-physicochemical processes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Li; He, Ya-Ling; Kang, Qinjun

2013-12-15

A coupled (hybrid) simulation strategy spatially combining the finite volume method (FVM) and the lattice Boltzmann method (LBM), called CFVLBM, is developed to simulate coupled multi-scale multi-physicochemical processes. In the CFVLBM, computational domain of multi-scale problems is divided into two sub-domains, i.e., an open, free fluid region and a region filled with porous materials. The FVM and LBM are used for these two regions, respectively, with information exchanged at the interface between the two sub-domains. A general reconstruction operator (RO) is proposed to derive the distribution functions in the LBM from the corresponding macro scalar, the governing equation of whichmore » obeys the convection–diffusion equation. The CFVLBM and the RO are validated in several typical physicochemical problems and then are applied to simulate complex multi-scale coupled fluid flow, heat transfer, mass transport, and chemical reaction in a wall-coated micro reactor. The maximum ratio of the grid size between the FVM and LBM regions is explored and discussed. -- Highlights: •A coupled simulation strategy for simulating multi-scale phenomena is developed. •Finite volume method and lattice Boltzmann method are coupled. •A reconstruction operator is derived to transfer information at the sub-domains interface. •Coupled multi-scale multiple physicochemical processes in micro reactor are simulated. •Techniques to save computational resources and improve the efficiency are discussed.« less

Fabrication of anti-adhesion surfaces on aluminium substrates of rubber plastic moulds using electrolysis plasma treatment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meng, Jianbing, E-mail: jianbingmeng@126.com; Dong, Xiaojuan; Wei, Xiuting

An anti-adhesion surface with a water contact angle of 167° was fabricated on aluminium samples of rubber plastic moulds by electrolysis plasma treatment using mixed electrolytes of C{sub 6}H{sub 5}O{sub 7}(NH{sub 4}){sub 3} and Na{sub 2}SO{sub 4}, followed by fluorination. To optimise the fabrication conditions, several important processing parameters such as the discharge voltage, discharge time, concentrations of supporting electrolyte and stearic acid ethanol solution were examined systematically. Using scanning electron microscopy (SEM) to analyse surfaces morphology, micrometer scale pits, and protrusions were found on the surface, with numerous nanometer mastoids contained in the protrusions. These binary micro/nano-scale structures, whichmore » are similar to the micro-structures of soil-burrowing animals, play a critical role in achieving low adhesion properties. Otherwise, the anti-adhesion behaviours of the resulting samples were analysed by the atomic force microscope (AFM), Fourier-transform infrared spectrophotometer (FTIR), electrons probe micro-analyzer (EPMA), optical contact angle meter, digital Vickers microhardness (Hv) tester, and electronic universal testing. The results show that the electrolysis plasma treatment does not require complex processing parameters, using a simple device, and is an environment-friendly and effective method. Under the optimised conditions, the contact angle (CA) for the modified anti-adhesion surface is up to 167°, the sliding angle (SA) is less than 2°, roughness of the sample surface is only 0.409μm. Moreover, the adhesion force and H{sub v} are 0. 9KN and 385, respectively.« less

High Fidelity Computational Analysis of CO2 Trapping at Pore Scales

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumar, Vinod

2013-07-13

With an alarming rise in carbon dioxide (CO2) emission from anthropogenic sources, CO2 sequestration has become an attractive choice to mitigate the emission. Some popular storage media for CO{sub 2} are oil reservoirs, deep coal-bed, and deep oceanic-beds. These have been used for the long term CO{sub 2} storage. Due to special lowering viscosity and surface tension property of CO{sub 2}, it has been widely used for enhanced oil recovery. The sites for CO{sub 2} sequestration or enhanced oil recovery mostly consist of porous rocks. Lack of knowledge of molecular mobility under confinement and molecule-surface interactions between CO2 and naturalmore » porous media results in generally governed by unpredictable absorption kinetics and total absorption capacity for injected fluids, and therefore, constitutes barriers to the deployment of this technology. Therefore, it is important to understand the flow dynamics of CO{sub 2} through the porous microstructures at the finest scale (pore-scale) to accurately predict the storage potential and long-term dynamics of the sequestered CO{sub 2}. This report discusses about pore-network flow modeling approach using variational method and analyzes simulated results this method simulations at pore-scales for idealized network and using Berea Sandstone CT scanned images. Variational method provides a promising way to study the kinetic behavior and storage potential at the pore scale in the presence of other phases. The current study validates variational solutions for single and two-phase Newtonian and single phase non-Newtonian flow through angular pores for special geometries whose analytical and/or empirical solutions are known. The hydraulic conductance for single phase flow through a triangular duct was also validated against empirical results derived from lubricant theory.« less

Scaling relations of halo cores for self-interacting dark matter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lin, Henry W.; Loeb, Abraham, E-mail: henrylin@college.harvard.edu, E-mail: aloeb@cfa.harvard.edu

2016-03-01

Using a simple analytic formalism, we demonstrate that significant dark matter self-interactions produce halo cores that obey scaling relations nearly independent of the underlying particle physics parameters such as the annihilation cross section and the mass of the dark matter particle. For dwarf galaxies, we predict that the core density ρ{sub c} and the core radius r{sub c} should obey ρ{sub c} r{sub c} ≈ 41 M{sub ⊙} pc{sup −2} with a weak mass dependence ∼ M{sup 0.2}. Remarkably, such a scaling relation has recently been empirically inferred. Scaling relations involving core mass, core radius, and core velocity dispersion are predicted and agree well with observationalmore » data. By calibrating against numerical simulations, we predict the scatter in these relations and find them to be in excellent agreement with existing data. Future observations can test our predictions for different halo masses and redshifts.« less

Determination of Black Hole Mass in Cyg X-1 by Scaling of Spectral Index-QPO Frequency Correlation

NASA Technical Reports Server (NTRS)

Shaposhnikov, Nickolai; Titarchuk, Lev

2007-01-01

It is well established that timing and spectral properties of Galactic Black Hole (BH) X-ray binaries (XRB) are strongly correlated. In particular, it has been shown that low frequency Quasi-Periodic Oscillation (QPO) nu(sub low) - photon index GAMMA correlation curves have a specific pattern. In a number of the sources studied the shape of the index-low frequency QPO correlations are self-similar with a position offset in the nu(sub low) - GAMMA plane determined by a BH mass M(sub BH). Specifically, Titarchuk & Fiorito (2004) gave strong theoretical and observational arguments that the QPO frequency values in this nu(sub low) - GAMMA correlation should be inversely proportional to M(sub BH). A simple translation of the correlation for a given source along frequency axis leads to the observed correlation for another source. As a result of this translation one can obtain a scaling factor which is simply a BH mass ratio for these particular sources. This property of the correlations offers a fundamentally new method for BH mass determination in XRBs. Here we use the observed QPO-index correlations observed in three BH sources: GRO J1655-40, GRS 1915+105 and Cyg X-1. The BH mass of (6.3 plus or minus 0.5) solar mass in GRO J1655-40 is obtained using optical observations. RXTE observations during the recent 2005 outburst yielded sufficient data to establish the correlation pattern during both rise and decay of the event. We use GRO J1655-40 as a standard reference source to measure the BH mass in Cyg X-1. We also revisit the GRS 1915+105 data as a further test of our scaling method. We obtain the BH mass in Cyg X-1 in the range 7.6-9.9.

The three-point function as a probe of models for large-scale structure

NASA Technical Reports Server (NTRS)

Frieman, Joshua A.; Gaztanaga, Enrique

1993-01-01

The consequences of models of structure formation for higher-order (n-point) galaxy correlation functions in the mildly non-linear regime are analyzed. Several variations of the standard Omega = 1 cold dark matter model with scale-invariant primordial perturbations were recently introduced to obtain more power on large scales, R(sub p) is approximately 20 h(sup -1) Mpc, e.g., low-matter-density (non-zero cosmological constant) models, 'tilted' primordial spectra, and scenarios with a mixture of cold and hot dark matter. They also include models with an effective scale-dependent bias, such as the cooperative galaxy formation scenario of Bower, etal. It is shown that higher-order (n-point) galaxy correlation functions can provide a useful test of such models and can discriminate between models with true large-scale power in the density field and those where the galaxy power arises from scale-dependent bias: a bias with rapid scale-dependence leads to a dramatic decrease of the hierarchical amplitudes Q(sub J) at large scales, r is approximately greater than R(sub p). Current observational constraints on the three-point amplitudes Q(sub 3) and S(sub 3) can place limits on the bias parameter(s) and appear to disfavor, but not yet rule out, the hypothesis that scale-dependent bias is responsible for the extra power observed on large scales.

Detection of the baryon acoustic peak in the large-scale correlation function of SDSS luminous red galaxies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eisenstein, Daniel J.; Zehavi, Idit; Hogg, David W.

2005-01-01

We present the large-scale correlation function measured from a spectroscopic sample of 46,748 luminous red galaxies from the Sloan Digital Sky Survey. The survey region covers 0.72h{sup -3} Gpc{sup 3} over 3816 square degrees and 0.16 < z < 0.47, making it the best sample yet for the study of large-scale structure. We find a well-detected peak in the correlation function at 100h{sup -1} Mpc separation that is an excellent match to the predicted shape and location of the imprint of the recombination-epoch acoustic oscillations on the low-redshift clustering of matter. This detection demonstrates the linear growth of structure bymore » gravitational instability between z {approx} 1000 and the present and confirms a firm prediction of the standard cosmological theory. The acoustic peak provides a standard ruler by which we can measure the ratio of the distances to z = 0.35 and z = 1089 to 4% fractional accuracy and the absolute distance to z = 0.35 to 5% accuracy. From the overall shape of the correlation function, we measure the matter density {Omega}{sub m}h{sup 2} to 8% and find agreement with the value from cosmic microwave background (CMB) anisotropies. Independent of the constraints provided by the CMB acoustic scale, we find {Omega}{sub m} = 0.273 {+-} 0.025 + 0.123(1 + w{sub 0}) + 0.137{Omega}{sub K}. Including the CMB acoustic scale, we find that the spatial curvature is {Omega}{sub K} = -0.010 {+-} 0.009 if the dark energy is a cosmological constant. More generally, our results provide a measurement of cosmological distance, and hence an argument for dark energy, based on a geometric method with the same simple physics as the microwave background anisotropies. The standard cosmological model convincingly passes these new and robust tests of its fundamental properties.« less

A quasi-Newton algorithm for large-scale nonlinear equations.

PubMed

Huang, Linghua

2017-01-01

In this paper, the algorithm for large-scale nonlinear equations is designed by the following steps: (i) a conjugate gradient (CG) algorithm is designed as a sub-algorithm to obtain the initial points of the main algorithm, where the sub-algorithm's initial point does not have any restrictions; (ii) a quasi-Newton algorithm with the initial points given by sub-algorithm is defined as main algorithm, where a new nonmonotone line search technique is presented to get the step length [Formula: see text]. The given nonmonotone line search technique can avoid computing the Jacobian matrix. The global convergence and the [Formula: see text]-order convergent rate of the main algorithm are established under suitable conditions. Numerical results show that the proposed method is competitive with a similar method for large-scale problems.

Hydrogen Selective Inorganic membranes for Gas Separations under High Pressure Intermediate Temperature Hydrocarbonic Envrionment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rich Ciora; Paul KT Liu

2012-06-27

In this project, we have successfully developed a full scale commercially ready carbon molecular sieve (CMS) based membrane for applications in H{sub 2} recovery from refinery waste and other aggressive gas streams. Field tests at a refinery pilot plant and a coal gasification facility have successfully demonstrated its ability to recovery hydrogen from hydrotreating and raw syngas respectively. High purity H{sub 2} and excellent stability of the membrane permeance and selectivity were obtained in testing conducted over >500 hours at each site. The results from these field tests as well as laboratory testing conclude that the membranes can be operated at high pressures (up to 1,000 psig) and temperatures (up to 300 C) in presence of aggressive contaminants, such as sulfur and nitrogen containing species (H{sub 2}S, CO{sub 2}, NH{sub 3}, etc), condensable hydrocarbons, tar-like species, heavy metals, etc. with no observable effect on membrane performance. By comparison, similar operating conditions and/or environments would rapidly destroy competing membranes, such as polymeric, palladium, zeolitic, etc. Significant cost savings can be achieved through recovering H{sub 2} from refinery waste gas using this newly developed CMS membrane. Annual savings ofmore » $$2 to 4MM/year (per 20,000 scfd of waste gas) can be realized by recovering the H{sub 2} for reuse (versus fuel). Projecting these values over the entire US market, potential H{sub 2} savings from refinery waste gases on the order of 750 to 1,000MM scfd and $$750 to $1,000MM per year are possible. In addition to the cost savings, potential energy savings are projected to be ca. 150 to 220 tBTU/yr and CO{sub 2} gas emission reductions are projected to be ca. 5,000 to 6,500MMtons/year. The full scale membrane bundle developed as part of this project, i.e., 85 x 30 inch ceramic membrane tubes packaged into a full ceramic potting, is an important accomplishment. No comparable commercial scale product exists in the inorganic membrane field. Further, this newly developed full scale bundle concept can be extended to other thin film inorganic membrane technology (Pd, zeolite, etc), providing a potential commercialization pathway for these membrane materials that demonstrate high potential in a variety of separation applications yet remain a laboratory 'novelty' for lack of a full scale support. Overall, the project has been highly successful and all of the project objectives have been met. We have developed the first of its kind commercial scale carbon molecular sieve membrane and demonstrated its performance in field testing under aggressive operating conditions and in the presence of chemical contaminants that would rapidly destroy alternative organic and inorganic membranes. This innovative membrane permits H{sub 2} recovery from gas streams that up until now have not been successfully treated with membrane or conventional technology. Our end user participant is currently pursuing the field demonstration of this membrane for hydrogen recovery at its refinery site.« less

How a creative storytelling intervention can improve medical student attitude towards persons with dementia: a mixed methods study.

PubMed

George, Daniel R; Stuckey, Heather L; Whitehead, Megan M

2014-05-01

The creative arts can integrate humanistic experiences into geriatric education. This experiential learning case study evaluated whether medical student participation in TimeSlips, a creative storytelling program with persons affected by dementia, would improve attitudes towards this patient population. Twenty-two fourth-year medical students participated in TimeSlips for one month. The authors analyzed pre- and post-program scores of items, sub-domains for comfort and knowledge, and overall scale from the Dementia Attitudes Scale using paired t-tests or Wilcoxon Signed-rank tests to evaluate mean change in students' self-reported attitudes towards persons with dementia. A case study approach using student reflective writing and focus group data was used to explain quantitative results. Twelve of the 20 items, the two sub-domains, and the overall Dementia Attitudes Scale showed significant improvement post-intervention. Qualitative analysis identified four themes that added insight to quantitative results: (a) expressions of fear and discomfort felt before storytelling, (b) comfort experienced during storytelling, (c) creativity and openness achieved through storytelling, and (d) humanistic perspectives developed during storytelling can influence future patient care. This study provides preliminary evidence that participation in a creative storytelling program improves medical student attitudes towards persons with dementia, and suggests mechanisms for why attitudinal changes occurred.

Multi-scale calculation based on dual domain material point method combined with molecular dynamics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dhakal, Tilak Raj

This dissertation combines the dual domain material point method (DDMP) with molecular dynamics (MD) in an attempt to create a multi-scale numerical method to simulate materials undergoing large deformations with high strain rates. In these types of problems, the material is often in a thermodynamically non-equilibrium state, and conventional constitutive relations are often not available. In this method, the closure quantities, such as stress, at each material point are calculated from a MD simulation of a group of atoms surrounding the material point. Rather than restricting the multi-scale simulation in a small spatial region, such as phase interfaces, or crackmore » tips, this multi-scale method can be used to consider non-equilibrium thermodynamic e ects in a macroscopic domain. This method takes advantage that the material points only communicate with mesh nodes, not among themselves; therefore MD simulations for material points can be performed independently in parallel. First, using a one-dimensional shock problem as an example, the numerical properties of the original material point method (MPM), the generalized interpolation material point (GIMP) method, the convected particle domain interpolation (CPDI) method, and the DDMP method are investigated. Among these methods, only the DDMP method converges as the number of particles increases, but the large number of particles needed for convergence makes the method very expensive especially in our multi-scale method where we calculate stress in each material point using MD simulation. To improve DDMP, the sub-point method is introduced in this dissertation, which provides high quality numerical solutions with a very small number of particles. The multi-scale method based on DDMP with sub-points is successfully implemented for a one dimensional problem of shock wave propagation in a cerium crystal. The MD simulation to calculate stress in each material point is performed in GPU using CUDA to accelerate the computation. The numerical properties of the multiscale method are investigated as well as the results from this multi-scale calculation are compared of particles needed for convergence makes the method very expensive especially in our multi-scale method where we calculate stress in each material point using MD simulation. To improve DDMP, the sub-point method is introduced in this dissertation, which provides high quality numerical solutions with a very small number of particles. The multi-scale method based on DDMP with sub-points is successfully implemented for a one dimensional problem of shock wave propagation in a cerium crystal. The MD simulation to calculate stress in each material point is performed in GPU using CUDA to accelerate the computation. The numerical properties of the multiscale method are investigated as well as the results from this multi-scale calculation are compared with direct MD simulation results to demonstrate the feasibility of the method. Also, the multi-scale method is applied for a two dimensional problem of jet formation around copper notch under a strong impact.« less

Aerosol based direct-write micro-additive fabrication method for sub-mm 3D metal-dielectric structures

NASA Astrophysics Data System (ADS)

Rahman, Taibur; Renaud, Luke; Heo, Deuk; Renn, Michael; Panat, Rahul

2015-10-01

The fabrication of 3D metal-dielectric structures at sub-mm length scale is highly important in order to realize low-loss passives and GHz wavelength antennas with applications in wearable and Internet-of-Things (IoT) devices. The inherent 2D nature of lithographic processes severely limits the available manufacturing routes to fabricate 3D structures. Further, the lithographic processes are subtractive and require the use of environmentally harmful chemicals. In this letter, we demonstrate an additive manufacturing method to fabricate 3D metal-dielectric structures at sub-mm length scale. A UV curable dielectric is dispensed from an Aerosol Jet system at 10-100 µm length scale and instantaneously cured to build complex 3D shapes at a length scale  <1 mm. A metal nanoparticle ink is then dispensed over the 3D dielectric using a combination of jetting action and tilted dispense head, also using the Aerosol Jet technique and at a length scale 10-100 µm, followed by the nanoparticle sintering. Simulation studies are carried out to demonstrate the feasibility of using such structures as mm-wave antennas. The manufacturing method described in this letter opens up the possibility of fabricating an entirely new class of custom-shaped 3D structures at a sub-mm length scale with potential applications in 3D antennas and passives.

Upstream H/sub 2/S removal from geothermal steam. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1981-11-01

The purpose of this project was to evaluate a new heat exchanger process as a method for removing hydrogen sulfide (H/sub 2/S) gas from geothermal steam upstream of a power plant turbine. The process utilizes a heat exchanger to condense geothermal steam so that noncondensable gases (including H/sub 2/S) can be removed in the form of a concentrated vent stream. Ultimate disposal of the removed H/sub 2/S gas may then be accomplished by use of other processes such as the commercially available Stretford process. The clean condensate is reevaporated on the other side of the heat exchanger using the heatmore » removed from the condensing geothermal steam. The necessary heat transfer is induced by maintaining a slight pressure difference, and consequently a slight temperature difference, between the two sides of the heat exchanger. Evaluation of this condensing and reboiling process was performed primarily through the testing of a small-scale 14 m/sup 2/ (150 ft/sup 2/) vertical tube evaporator heat exchanger at The Geysers Power Plant in northern California. The field test results demonstrated H/sub 2/S removal rates consistently better than 90 percent, with an average removal rate of 94 percent. In addition, the removal rate for all noncondensable gases is about 98 percent. Heat transfer rates were high enough to indicate acceptable economics for application of the process on a commercial scale. The report also includes an evaluation of the cost and performance of various configurations of the system, and presents design and cost estimates for a 2.5 MWe and a 55 MWe unit.« less

Scaling between reanalyses and high-resolution land-surface modelling in mountainous areas - enabling better application and testing of reanalyses in heterogeneous environments

NASA Astrophysics Data System (ADS)

Gruber, S.; Fiddes, J.

2013-12-01

In mountainous topography, the difference in scale between atmospheric reanalyses (typically tens of kilometres) and relevant processes and phenomena near the Earth surface, such as permafrost or snow cover (meters to tens of meters) is most obvious. This contrast of scales is one of the major obstacles to using reanalysis data for the simulation of surface phenomena and to confronting reanalyses with independent observation. At the example of modelling permafrost in mountain areas (but simple to generalise to other phenomena and heterogeneous environments), we present and test methods against measurements for (A) scaling atmospheric data from the reanalysis to the ground level and (B) smart sampling of the heterogeneous landscape in order to set up a lumped model simulation that represents the high-resolution land surface. TopoSCALE (Part A, see http://dx.doi.org/10.5194/gmdd-6-3381-2013) is a scheme, which scales coarse-grid climate fields to fine-grid topography using pressure level data. In addition, it applies necessary topographic corrections e.g. those variables required for computation of radiation fields. This provides the necessary driving fields to the LSM. Tested against independent ground data, this scheme has been shown to improve the scaling and distribution of meteorological parameters in complex terrain, as compared to conventional methods, e.g. lapse rate based approaches. TopoSUB (Part B, see http://dx.doi.org/10.5194/gmd-5-1245-2012) is a surface pre-processor designed to sample a fine-grid domain (defined by a digital elevation model) along important topographical (or other) dimensions through a clustering scheme. This allows constructing a lumped model representing the main sources of fine-grid variability and applying a 1D LSM efficiently over large areas. Results can processed to derive (i) summary statistics at coarse-scale re-analysis grid resolution, (ii) high-resolution data fields spatialized to e.g., the fine-scale digital elevation model grid, or (iii) validation products for locations at which measurements exist, only. The ability of TopoSUB to approximate results simulated by a 2D distributed numerical LSM at a factor of ~10,000 less computations is demonstrated by comparison of 2D and lumped simulations. Successful application of the combined scheme in the European Alps is reported and based on its results, open issues for future research are outlined.

Flower-like nanostructure MNb{sub 2}O{sub 6} (M = Mn, Zn) with high surface area: Hydrothermal synthesis and enhanced photocatalytic performance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Xue; Jing, Yan; Yang, Jia

Graphical abstract: - Highlights: • MNb{sub 2}O{sub 6} was prepared by a mild two-step hydrothermal method. • Their flower-like nanostructure morphology was studied by SEM and TEM. • High BET surface areas for MnNb{sub 2}O{sub 6} (∼50 m{sup 2}/g) and ZnNb{sub 2}O{sub 6} (∼100 m{sup 2}/g). • Band gap energies were estimated by UV–vis diffuse reflectance spectra. • Photocatalytic activities were evaluated under UV-light irradiation. - Abstract: Nano-scaled MNb{sub 2}O{sub 6} (M = Mn, Zn) was successfully synthesized via a two-step hydrothermal method. It is important to control the exact pH of the reaction solution in order to obtain puremore » products. The as-prepared samples both crystallize in the columbite structure. Interestingly, the products possess a flower-like morphology in a pseudo-six-fold symmetry, which is in fact arrayed by two-dimensional nanosheets. Their surface areas (51 m{sup 2}/g for MnNb{sub 2}O{sub 6} and 103 m{sup 2}/g for ZnNb{sub 2}O{sub 6}) are about 25–50 times of those prepared by solid state reaction. UV–vis diffuse reflectance spectra show the nano-scaled sample has a stronger absorption and a narrower band gap than its bulk form. The estimated band gap energies are 2.70 eV (MnNb{sub 2}O{sub 6}) and 3.77 eV (ZnNb{sub 2}O{sub 6}), respectively. The nano-scaled ZnNb{sub 2}O{sub 6} exhibits a double enhancement of photocatalytic activity in the decolorization of methylene blue than bulk ZnNb{sub 2}O{sub 6}.« less

EVALUATION OF ARG-1 SAMPLES PREPARED BY CESIUM CARBONATE DISSOLUTION DURING THE ISOLOK SME ACCEPTABILITY TESTING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Edwards, T.; Hera, K.; Coleman, C.

2011-12-05

Evaluation of Defense Waste Processing Facility (DWPF) Chemical Process Cell (CPC) cycle time identified several opportunities to improve the CPC processing time. The Mechanical Systems & Custom Equipment Development (MS&CED) Section of the Savannah River National Laboratory (SRNL) recently completed the evaluation of one of these opportunities - the possibility of using an Isolok sampling valve as an alternative to the Hydragard valve for taking DWPF process samples at the Slurry Mix Evaporator (SME). The use of an Isolok for SME sampling has the potential to improve operability, reduce maintenance time, and decrease CPC cycle time. The SME acceptability testingmore » for the Isolok was requested in Task Technical Request (TTR) HLW-DWPF-TTR-2010-0036 and was conducted as outlined in Task Technical and Quality Assurance Plan (TTQAP) SRNLRP-2011-00145. RW-0333P QA requirements applied to the task, and the results from the investigation were documented in SRNL-STI-2011-00693. Measurement of the chemical composition of study samples was a critical component of the SME acceptability testing of the Isolok. A sampling and analytical plan supported the investigation with the analytical plan directing that the study samples be prepared by a cesium carbonate (Cs{sub 2}CO{sub 3}) fusion dissolution method and analyzed by Inductively Coupled Plasma - Optical Emission Spectroscopy (ICP-OES). The use of the cesium carbonate preparation method for the Isolok testing provided an opportunity for an additional assessment of this dissolution method, which is being investigated as a potential replacement for the two methods (i.e., sodium peroxide fusion and mixed acid dissolution) that have been used at the DWPF for the analysis of SME samples. Earlier testing of the Cs{sub 2}CO{sub 3} method yielded promising results which led to a TTR from Savannah River Remediation, LLC (SRR) to SRNL for additional support and an associated TTQAP to direct the SRNL efforts. A technical report resulting from this work was issued that recommended that the mixed acid method be replaced by the Cs{sub 2}CO{sub 3} method for the measurement of magnesium (Mg), sodium (Na), and zirconium (Zr) with additional testing of the method by DWPF Laboratory being needed before further implementation of the Cs{sub 2}CO{sub 3} method at that laboratory. While the SME acceptability testing of the Isolok does not address any of the open issues remaining after the publication of the recommendation for the replacement of the mixed acid method by the Cs{sub 2}CO{sub 3} method (since those issues are to be addressed by the DWPF Laboratory), the Cs{sub 2}CO{sub 3} testing associated with the Isolok testing does provide additional insight into the performance of the method as conducted by SRNL. The performance is to be investigated by looking to the composition measurement data generated by the samples of a standard glass, the Analytical Reference Glass - 1 (ARG-1), that were prepared by the Cs{sub 2}CO{sub 3} method and included in the SME acceptability testing of the Isolok. The measurements of these samples were presented as part of the study results, but no statistical analysis of these measurements was conducted as part of those results. It is the purpose of this report to provide that analysis, which was supported using JMP Version 7.0.2.« less

Testing the Merger Paradigm: X-ray Observations of Radio-Selected Sub-Galactic-Scale Binary AGNs

NASA Astrophysics Data System (ADS)

Fu, Hai

2016-09-01

Interactions play an important role in galaxy evolution. Strong gas inflows are expected in the process of gas-rich mergers, which may fuel intense black hole accretion and star formation. Sub-galactic-scale binary/dual AGNs thus offer elegant laboratories to study the merger-driven co-evolution phase. However, previous samples of kpc-scale binaries are small and heterogeneous. We have identified a flux-limited sample of kpc-scale binary AGNs uniformly from a wide-area high-resolution radio survey conducted by the VLA. Here we propose Chandra X-ray characterization of a subset of four radio-confirmed binary AGNs at z 0.1. Our goal is to compare their X-ray properties with those of matched control samples to test the merger-driven co-evolution paradigm.

Development Program of IS Process Pilot Test Plant for Hydrogen Production With High-Temperature Gas-Cooled Reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jin Iwatsuki; Atsuhiko Terada; Hiroyuki Noguchi

2006-07-01

At the present time, we are alarmed by depletion of fossil energy and effects on global environment such as acid rain and global warming, because our lives depend still heavily on fossil energy. So, it is universally recognized that hydrogen is one of the best energy media and its demand will be increased greatly in the near future. In Japan, the Basic Plan for Energy Supply and Demand based on the Basic Law on Energy Policy Making was decided upon by the Cabinet on 6 October, 2003. In the plan, efforts for hydrogen energy utilization were expressed as follows; hydrogenmore » is a clean energy carrier without carbon dioxide (CO{sub 2}) emission, and commercialization of hydrogen production system using nuclear, solar and biomass, not fossil fuels, is desired. However, it is necessary to develop suitable technology to produce hydrogen without CO{sub 2} emission from a view point of global environmental protection, since little hydrogen exists naturally. Hydrogen production from water using nuclear energy, especially the high-temperature gas-cooled reactor (HTGR), is one of the most attractive solutions for the environmental issue, because HTGR hydrogen production by water splitting methods such as a thermochemical iodine-sulfur (IS) process has a high possibility to produce hydrogen effectively and economically. The Japan Atomic Energy Agency (JAEA) has been conducting the HTTR (High-Temperature Engineering Test Reactor) project from the view to establishing technology base on HTGR and also on the IS process. In the IS process, raw material, water, is to be reacted with iodine (I{sub 2}) and sulfur dioxide (SO{sub 2}) to produce hydrogen iodide (HI) and sulfuric acid (H{sub 2}SO{sub 4}), the so-called Bunsen reaction, which are then decomposed endo-thermically to produce hydrogen (H{sub 2}) and oxygen (O{sub 2}), respectively. Iodine and sulfur dioxide produced in the decomposition reactions can be used again as the reactants in the Bunsen reaction. In JAEA, continuous hydrogen production was demonstrated with the hydrogen production rate of about 30 NL/hr for one week using a bench-scale test apparatus made of glass. Based on the test results and know-how obtained through the bench-scale tests, a pilot test plant that can produce hydrogen of about 30 Nm{sup 3}/hr is being designed. The test plant will be fabricated with industrial materials such as glass coated steel, SiC ceramics etc, and operated under high pressure condition up to 2 MPa. The test plant will consist of a IS process plant and a helium gas (He) circulation facility (He loop). The He loop can simulate HTTR operation conditions, which consists of a 400 kW-electric heater for He hating, a He circulator and a steam generator working as a He cooler. In parallel to the design study, key components of the IS process such as the sulfuric acid (H{sub 2}SO{sub 4}) and the sulfur trioxide (SO{sub 3}) decomposers working under-high temperature corrosive environments have been designed and test-fabricated to confirm their fabricability. Also, other R and D's are under way such as corrosion, processing of HIx solutions. This paper describes present status of these activities. (authors)« less

NUMERICAL CONVERGENCE IN SMOOTHED PARTICLE HYDRODYNAMICS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhu, Qirong; Li, Yuexing; Hernquist, Lars

2015-02-10

We study the convergence properties of smoothed particle hydrodynamics (SPH) using numerical tests and simple analytic considerations. Our analysis shows that formal numerical convergence is possible in SPH only in the joint limit N → ∞, h → 0, and N{sub nb} → ∞, where N is the total number of particles, h is the smoothing length, and N{sub nb} is the number of neighbor particles within the smoothing volume used to compute smoothed estimates. Previous work has generally assumed that the conditions N → ∞ and h → 0 are sufficient to achieve convergence, while holding N{sub nb} fixed.more » We demonstrate that if N{sub nb} is held fixed as the resolution is increased, there will be a residual source of error that does not vanish as N → ∞ and h → 0. Formal numerical convergence in SPH is possible only if N{sub nb} is increased systematically as the resolution is improved. Using analytic arguments, we derive an optimal compromise scaling for N{sub nb} by requiring that this source of error balance that present in the smoothing procedure. For typical choices of the smoothing kernel, we find N{sub nb} ∝N {sup 0.5}. This means that if SPH is to be used as a numerically convergent method, the required computational cost does not scale with particle number as O(N), but rather as O(N {sup 1} {sup +} {sup δ}), where δ ≈ 0.5, with a weak dependence on the form of the smoothing kernel.« less

Assessing nurse-patient interactions from a caring perspective: report of the development and preliminary psychometric testing of the Caring Nurse--Patient Interactions Scale.

PubMed

Cossette, Sylvie; Cara, Chantal; Ricard, Nicole; Pepin, Jacinthe

2005-08-01

While there is a large body of literature regarding caring in nursing and some measurement tools addressing the concept have been developed, limitations of existing instruments constrain theory-driven research on nurse-patient interactions. The purpose of this paper is to describe the development and initial psychometric evaluation of the Caring Nurse-Patient Interactions Scale in a sample of 332 nurses and nursing students. The tool intended to facilitate research on the links between caring and patient outcomes. A content validity approach involving 13 expert nurses resulted in a 70-item tool sub-divided into 10 nursing carative factors. Alpha coefficients between sub-scales varied from .73 to .91 and sub-scales inter-correlations ranged from .53 to .89. Pearson correlation coefficients ranged from --.02 to .32 between the sub-scales and social desirability suggesting low to moderate bias. Results of the contrasted group approach partially supported the hypotheses while all differences were in the expected direction. Results suggest that the scale has strong potential for use in research, clinical and educational settings.

Uptakes of Cs and Sr on San Joaquin soil measured following ASTM method C1733.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ebert, W.L.; Petri, E.T.

2012-04-04

Series of tests were conducted following ASTM Standard Procedure C1733 to evaluate the repeatability of the test and the effects of several test parameters, including the solution-to-soil mass ratio, test duration, pH, and the concentrations of contaminants in the solution. This standard procedure is recommended for measuring the distribution coefficient (K{sub d}) of a contaminant in a specific soil/groundwater system. One objective of the current tests was to identify experimental conditions that can be used in future interlaboratory studies to determine the reproducibility of the test method. This includes the recommendation of a standard soil, the range of contaminant concentrationsmore » and solution matrix, and various test parameters. Quantifying the uncertainty in the distribution coefficient that can be attributed to the test procedure itself allows the differences in measured values to be associated with differences in the natural systems being studied. Tests were conducted to measure the uptake of Cs and Sr dissolved as CsCl and Sr(NO{sub 3}){sub 2} in a dilute NaHCO{sub 3}/SiO{sub 2} solution (representing contaminants in a silicate groundwater) by a NIST standard reference material of San Joaquin soil (SRM 2709a). Tests were run to measure the repeatability of the method and the sensitivity of the test response to the reaction time, the mass of soil used (at a constant soil-to-solution ratio), the solution pH, and the contaminant concentration. All tests were conducted in screw-top Teflon vessels at 30 C in an oven. All solutions were passed through a 0.45-{mu}m pore size cellulose acetate membrane filter and stabilized with nitric acid prior to analysis with inductively-coupled plasma mass spectrometry (ICP-MS). Scoping tests with soil in demineralized water resulted in a solution pH of about 8.0 and the release of small amounts of Sr from the soil. Solutions were made with targeted concentrations of 1 x 10{sup -6} m, 1 x 10{sup -5} m, 2.5 x 10{sup -5} m, 5 x 10{sup -5} m, 1 x 10{sup -4} m, and 5 x 10{sup -4} m to measure the effects of the Cs and Sr concentrations on their uptake by the soil. The pH values of all solutions were adjusted to about pH 8.5 so that the effects of pH and concentration could be measured separately. The 1 x 10{sup -4} m solutions were used to measure the repeatability of the test and the effects of duration, scale, and imposed pH on the test response.« less

Rasch analysis of the Patient Rated Elbow Evaluation questionnaire.

PubMed

Vincent, Joshua I; MacDermid, Joy C; King, Graham J W; Grewal, Ruby

2015-06-20

The Patient Rated Elbow Evaluation (PREE) was developed as an elbow joint specific measure of pain and disability and validated with classical psychometric methods. More recently, Rasch analysis has contributed new methods for analyzing the clinical measurement properties of self-report outcome measures. The objective of the study was to determine aspects of validity of the PREE using the Rasch model to assess the overall fit of the PREE data, the response scaling, individual item fit, differential item functioning (DIF), local dependency, unidimensionality and person separation index (PSI). A convenience sample of 236 patients (Age range 21-79 years; M: F- 97:139) with elbow disorders were recruited from the Roth│McFarlane Hand and Upper Limb Centre, London, Ontario, Canada. The baseline scores of the PREE were used. Rasch analysis was conducted using RUMM 2030 software on the 3 sub scales of the PREE separately. The 3 sub scales showed misfit initially with disordered thresholds on17 out of 20 items), uniform DIF was observed for two items ("Carrying a 10lbs object" from specific activities subscale for age group; and "household work" from the usual activities subscale for gender); multidimensionality and local dependency. The Pain subscale satisfied Rasch expectations when item 2 "Pain - At rest" was split for age group, while the usual activities subscale readily stood up to Rasch requirements when the item 2 "household work" was split for gender. The specific activities subscale demonstrated fit to the Rasch model when sub test analysis accounted for local dependency. All three subscales of the PREE were well targeted and had high reliability (PSI >0.80). The three subscales of the PREE appear to be robust when tested against the Rasch model when subject to a few alterations. The value of changing the 0-10 format is questionable given its widespread use; further Rasch-based analysis of whether these findings are stable in other samples is warranted.

Electrochemical method of producing nano-scaled graphene platelets

DOEpatents

Zhamu, Aruna; Jang, Joan; Jang, Bor Z.

2013-09-03

A method of producing nano-scaled graphene platelets with an average thickness smaller than 30 nm from a layered graphite material. The method comprises (a) forming a carboxylic acid-intercalated graphite compound by an electrochemical reaction; (b) exposing the intercalated graphite compound to a thermal shock to produce exfoliated graphite; and (c) subjecting the exfoliated graphite to a mechanical shearing treatment to produce the nano-scaled graphene platelets. Preferred carboxylic acids are formic acid and acetic acid. The exfoliation step in the instant invention does not involve the evolution of undesirable species, such as NO.sub.x and SO.sub.x, which are common by-products of exfoliating conventional sulfuric or nitric acid-intercalated graphite compounds. The nano-scaled platelets are candidate reinforcement fillers for polymer nanocomposites. Nano-scaled graphene platelets are much lower-cost alternatives to carbon nano-tubes or carbon nano-fibers.

COSMOS: STOCHASTIC BIAS FROM MEASUREMENTS OF WEAK LENSING AND GALAXY CLUSTERING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jullo, Eric; Rhodes, Jason; Kiessling, Alina

2012-05-01

In the theory of structure formation, galaxies are biased tracers of the underlying matter density field. The statistical relation between galaxy and matter density field is commonly referred to as galaxy bias. In this paper, we test the linear bias model with weak-lensing and galaxy clustering measurements in the 2 deg{sup 2} COSMOS field. We estimate the bias of galaxies between redshifts z = 0.2 and z = 1 and over correlation scales between R = 0.2 h{sup -1} Mpc and R = 15 h{sup -1} Mpc. We focus on three galaxy samples, selected in flux (simultaneous cuts I{sub 814W}more » < 26.5 and K{sub s} < 24) and in stellar mass (10{sup 9} < M{sub *} < 10{sup 10} h{sup -2} M{sub Sun} and 10{sup 10} < M{sub *} < 10{sup 11} h{sup -2} M{sub Sun }). At scales R > 2 h{sup -1} Mpc, our measurements support a model of bias increasing with redshift. The Tinker et al. fitting function provides a good fit to the data. We find the best-fit mass of the galaxy halos to be log (M{sub 200}/h{sup -1} M{sub Sun }) = 11.7{sup +0.6}{sub -1.3} and log (M{sub 200}/h{sup -1} M{sub Sun }) = 12.4{sup +0.2}{sub -2.9}, respectively, for the low and high stellar-mass samples. In the halo model framework, bias is scale dependent with a change of slope at the transition scale between the one and the two halo terms. We detect a scale dependence of bias with a turndown at scale R = 2.3 {+-} 1.5 h{sup -1} Mpc, in agreement with previous galaxy clustering studies. We find no significant amount of stochasticity, suggesting that a linear bias model is sufficient to describe our data. We use N-body simulations to quantify both the amount of cosmic variance and systematic errors in the measurement.« less

Development of a Low-Cost Sub-Scale Aircraft for Flight Research: The FASER Project

NASA Technical Reports Server (NTRS)

Owens, Donald B.; Cox, David E.; Morelli, Eugene A.

2006-01-01

An inexpensive unmanned sub-scale aircraft was developed to conduct frequent flight test experiments for research and demonstration of advanced dynamic modeling and control design concepts. This paper describes the aircraft, flight systems, flight operations, and data compatibility including details of some practical problems encountered and the solutions found. The aircraft, named Free-flying Aircraft for Sub-scale Experimental Research, or FASER, was outfitted with high-quality instrumentation to measure aircraft inputs and states, as well as vehicle health parameters. Flight data are stored onboard, but can also be telemetered to a ground station in real time for analysis. Commercial-off-the-shelf hardware and software were used as often as possible. The flight computer is based on the PC104 platform, and runs xPC-Target software. Extensive wind tunnel testing was conducted with the same aircraft used for flight testing, and a six degree-of-freedom simulation with nonlinear aerodynamics was developed to support flight tests. Flight tests to date have been conducted to mature the flight operations, validate the instrumentation, and check the flight data for kinematic consistency. Data compatibility analysis showed that the flight data are accurate and consistent after corrections are made for estimated systematic instrumentation errors.

Comparison of methods for assessing thyroid function in nonthyroidal illness

DOE Office of Scientific and Technical Information (OSTI.GOV)

Melmed, S.; Geola, F.L.; Reed, A.W.

1982-02-01

Various tests of thyroid function were studied in sick patients with nonthyroidal illness (NTI) in order to determine the utility of each test for differentiating these patients from a group with hypothyroidism. We evaluated each test in 22 healthy volunteers who served as controls, 20 patients with hypothyroidism, 14 patients admitted to medical intensive care unit whose serum T/sub 4/ was less than 5 ..mu..g/dl, 13 patients with chronic liver disease, 32 patients on chronic hemodialysis for renal failure, 13 ambulatory oncology patients receiving chemotherapy 16 pregnant women, 7 women on estrogens, and 20 hyperthyroid patients. On all samples, wemore » measured serum T/sub 4/, the free T/sub 4/ index by several methods, free T/sub 4/ by equilibrium dialysis, free T/sub 4/ calculated from thyronine-binding globulin (TBG) RIA, free T/sub 4/ by three commercial kits (Gammacoat, Immophase, and Liquisol), T/sub 3/, rT/sub 3/, and TSH (by 3 different RIA). Although all of the methods used for measuring free T/sub 4/ (including free T/sub 4/ index, free T/sub 4/ by dialysis, free T/sub 4/ assessed by TBG, and free T/sub 4/ assessed by the 3 commercial kits) were excellent for the diagnosis of hypothyroidism, hyperthyroidism, and euthyroidism in the presence of high TBG, none of these methods showed that free T/sub 4/ was consistently normal in patients with NTI; with each method, a number of NTI patients had subnormal values. In the NTI groups, free T/sub 4/ measured by dialysis and the free T/sub 4/ index generally correlated significantly with the commercial free T/sub 4/ methods. Serum rT/sub 3/ was elevated or normal in NTI patients and low in hypothyroid subjects. Serum TSH provided the most reliable differentiation between patients with primary hypothyroidism and those with NTI and low serum T/sub 4/ levels.« less

Charge carrier recombination dynamics in perovskite and polymer solar cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paulke, Andreas; Kniepert, Juliane; Kurpiers, Jona

2016-03-14

Time-delayed collection field experiments are applied to planar organometal halide perovskite (CH{sub 3}NH{sub 3}PbI{sub 3}) based solar cells to investigate charge carrier recombination in a fully working solar cell at the nanosecond to microsecond time scale. Recombination of mobile (extractable) charges is shown to follow second-order recombination dynamics for all fluences and time scales tested. Most importantly, the bimolecular recombination coefficient is found to be time-dependent, with an initial value of ca. 10{sup −9} cm{sup 3}/s and a progressive reduction within the first tens of nanoseconds. Comparison to the prototypical organic bulk heterojunction device PTB7:PC{sub 71}BM yields important differences with regardmore » to the mechanism and time scale of free carrier recombination.« less

Laboratory flow experiments for visualizing carbon dioxide-induced, density-driven brine convection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kneafsey, T.; Pruess, K.

2009-09-01

Injection of carbon dioxide (CO{sub 2}) into saline aquifers confined by low-permeability cap rock will result in a layer of CO{sub 2} overlying the brine. Dissolution of CO{sub 2} into the brine increases the brine density, resulting in an unstable situation in which more-dense brine overlies less-dense brine. This gravitational instability could give rise to density-driven convection of the fluid, which is a favorable process of practical interest for CO{sub 2} storage security because it accelerates the transfer of buoyant CO{sub 2} into the aqueous phase, where it is no longer subject to an upward buoyant drive. Laboratory flow visualizationmore » tests in transparent Hele-Shaw cells have been performed to elucidate the processes and rates of this CO{sub 2} solute-driven convection (CSC). Upon introduction of CO{sub 2} into the system, a layer of CO{sub 2}-laden brine forms at the CO{sub 2}-water interface. Subsequently, small convective fingers form, which coalesce, broaden, and penetrate into the test cell. Images and time-series data of finger lengths and wavelengths are presented. Observed CO{sub 2} uptake of the convection system indicates that the CO{sub 2} dissolution rate is approximately constant for each test and is far greater than expected for a diffusion-only scenario. Numerical simulations of our system show good agreement with the experiments for onset time of convection and advancement of convective fingers. There are differences as well, the most prominent being the absence of cell-scale convection in the numerical simulations. This cell-scale convection observed in the experiments is probably initiated by a small temperature gradient induced by the cell illumination.« less

Studies of Sub-Synchronous Oscillations in Large-Scale Wind Farm Integrated System

NASA Astrophysics Data System (ADS)

Yue, Liu; Hang, Mend

2018-01-01

With the rapid development and construction of large-scale wind farms and grid-connected operation, the series compensation wind power AC transmission is gradually becoming the main way of power usage and improvement of wind power availability and grid stability, but the integration of wind farm will change the SSO (Sub-Synchronous oscillation) damping characteristics of synchronous generator system. Regarding the above SSO problem caused by integration of large-scale wind farms, this paper focusing on doubly fed induction generator (DFIG) based wind farms, aim to summarize the SSO mechanism in large-scale wind power integrated system with series compensation, which can be classified as three types: sub-synchronous control interaction (SSCI), sub-synchronous torsional interaction (SSTI), sub-synchronous resonance (SSR). Then, SSO modelling and analysis methods are categorized and compared by its applicable areas. Furthermore, this paper summarizes the suppression measures of actual SSO projects based on different control objectives. Finally, the research prospect on this field is explored.

Continuous bench-scale slurry catalyst testing direct coal liquefaction rawhide sub-bituminous coal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bauman, R.F.; Coless, L.A.; Davis, S.M.

In 1992, the Department of Energy (DOE) sponsored research to demonstrate a dispersed catalyst system using a combination of molybdenum and iron precursors for direct coal liquefaction. This dispersed catalyst system was successfully demonstrated using Black Thunder sub-bituminous coal at Wilsonville, Alabama by Southern Electric International, Inc. The DOE sponsored research continues at Exxon Research and Development Laboratories (ERDL). A six month continuous bench-scale program using ERDL`s Recycle Coal Liquefaction Unit (RCLU) is planned, three months in 1994 and three months in 1995. The initial conditions in RCLU reflect experience gained from the Wilsonville facility in their Test Run 263.more » Rawhide sub-bituminous coal which is similar to the Black Thunder coal tested at Wilsonville was used as the feed coal. A slate of five dispersed catalysts for direct coal liquefaction of Rawhide sub-bituminous coal has been tested. Throughout the experiments, the molybdenum addition rate was held constant at 100 wppm while the iron oxide addition rate was varied from 0.25 to 1.0 weight percent (dry coal basis). This report covers the 1994 operations and accomplishments.« less

Continuous bench-scale slurry catalyst testing direct coal liquefaction of rawhide sub-bituminous coal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bauman, R.F.; Coless, L.A.; Davis, S.M.

In 1992, the Department of Energy (DOE) sponsored research to demonstrate a dispersed catalyst system using a combination of molybdenum and iron precursors for direct coal liquefaction. This dispersed catalyst system was successfully demonstrated using Black Thunder sub-bituminous coal at Wilsonville, Alabama by Southern Electric International, Inc. The DOE sponsored research continues at Exxon Research and Development Laboratories (ERDL). A six month continuous bench-scale program using ERDL`s Recycle Coal Liquefaction Unit (RCLU) is planned, three months in 1994 and three months in 1995. The initial conditions in RCLU reflect experience gained from the Wilsonville facility in their Test Run 263.more » Rawhide sub-bituminous coal which is similar to the Black Thunder coal tested at Wilsonville was used as the feed coal. A slate of five dispersed catalysts for direct coal liquefaction of Rawhide sub-bituminous coal has been tested. Throughout the experiments, the molybdenum addition rate was held constant at 100 wppm while the iron oxide addition rate was varied from 0.25 to 1.0 weight percent (dry coal basis). This report covers the 1994 operations and accomplishments.« less

Multidisciplinary assessment measure for individuals with disorders of consciousness.

PubMed

Gollega, Ana; Meghji, Chamine; Renton, Sharon; Lazoruk, Arlene; Haynes, Elizabeth; Lawson, Denise; Ostapovitch, MaryAnne

2015-01-01

This study introduces the Comprehensive Assessment Measure for the Minimally Responsive Individual (CAMMRI) and reports on its development, inter-rater reliability, construct validity and clinical value. A multidisciplinary team of therapists developed this measure, which comprises 12 sub-tests that examine three main areas: Response to the Environment, Motor Control and Communication and Swallowing. The sub-tests are scored using a 7-point scale; sub-tests can also be administered individually. The measure was administered during a pilot project and then 1 year later to 12 adult clients with severe acquired brain injury at a long-term rehabilitation programme. The age range of the participants was 18-65 years; individuals were 1.5-10 years post-injury. Comparison measures included the Western Neuro Sensory Stimulation Profile (WNSSP), the Coma Recovery Scale-Revised (CRS-R) and the Chedoke McMaster Impairment Inventory (CMII). Inter-rater reliability of each sub-test ranged from 0.87-1.0, with an average of 0.90 in the first year of the assessments. Validity data supported the use of the CAMMRI for minimally conscious adults with ABI to measure behavioural changes and plan treatment for this population. Future research should focus on using this measure with other neurological populations.

Improvements in sub-grid, microphysics averages using quadrature based approaches

NASA Astrophysics Data System (ADS)

Chowdhary, K.; Debusschere, B.; Larson, V. E.

2013-12-01

Sub-grid variability in microphysical processes plays a critical role in atmospheric climate models. In order to account for this sub-grid variability, Larson and Schanen (2013) propose placing a probability density function on the sub-grid cloud microphysics quantities, e.g. autoconversion rate, essentially interpreting the cloud microphysics quantities as a random variable in each grid box. Random sampling techniques, e.g. Monte Carlo and Latin Hypercube, can be used to calculate statistics, e.g. averages, on the microphysics quantities, which then feed back into the model dynamics on the coarse scale. We propose an alternate approach using numerical quadrature methods based on deterministic sampling points to compute the statistical moments of microphysics quantities in each grid box. We have performed a preliminary test on the Kessler autoconversion formula, and, upon comparison with Latin Hypercube sampling, our approach shows an increased level of accuracy with a reduction in sample size by almost two orders of magnitude. Application to other microphysics processes is the subject of ongoing research.

Carbon fiber reinforced hierarchical orthogrid stiffened cylinder: Fabrication and testing

NASA Astrophysics Data System (ADS)

Wu, Hao; Lai, Changlian; Sun, Fangfang; Li, Ming; Ji, Bin; Wei, Weiyi; Liu, Debo; Zhang, Xi; Fan, Hualin

2018-04-01

To get strong, stiff and light cylindrical shell, carbon fiber reinforced hierarchical orthogrid stiffened cylinders are designed and fabricated. The cylinder is stiffened by two-scale orthogrid. The primary orthogrid has thick and high ribs and contains several sub-orthogrid cells whose rib is much thinner and lower. The primary orthogrid stiffens the bending rigidity of the cylinder to resist the global instability while the sub-orthogrid stiffens the bending rigidity of the skin enclosed by the primary orthogrid to resist local buckling. The cylinder is fabricated by filament winding method based on a silicone rubber mandrel with hierarchical grooves. Axial compression tests are performed to reveal the failure modes. With hierarchical stiffeners, the cylinder fails at skin fracture and has high specific strength. The cylinder will fail at end crushing if the end of the cylinder is not thickened. Global instability and local buckling are well restricted by the hierarchical stiffeners.

Testing the Job Demand-Control-Support model with anxiety and depression as outcomes: the Hordaland Health Study.

PubMed

Sanne, Bjarte; Mykletun, Arnstein; Dahl, Alv A; Moen, Bente E; Tell, Grethe S

2005-09-01

To test the strain/iso-strain, interaction and buffer hypotheses of the Job Demand-Control-Support model in relation to anxiety and depression. Five thousand five hundred and sixty-two workers with valid Demand-Control-Support Questionnaire (DCSQ) scores were examined with the sub-scales of the Hospital Anxiety and Depression Scale as outcomes. Multiple statistical methods were applied. The strain and iso-strain hypotheses were confirmed. Generally, additive and non-interaction effects were found between psychological demands, control and social support. The buffer hypotheses were refuted. Results from analyses testing different interaction operationalizations were complementary. High demands, low control and low support individually, but particularly combined, are risk factors for anxiety and depression. Support is the DCSQ index most strongly associated with anxiety and depression in women. Assessment of psychosocial work environment may identify workers at risk, and serve as a basis for job-redesign.

On the sub-model errors of a generalized one-way coupling scheme for linking models at different scales

NASA Astrophysics Data System (ADS)

Zeng, Jicai; Zha, Yuanyuan; Zhang, Yonggen; Shi, Liangsheng; Zhu, Yan; Yang, Jinzhong

2017-11-01

Multi-scale modeling of the localized groundwater flow problems in a large-scale aquifer has been extensively investigated under the context of cost-benefit controversy. An alternative is to couple the parent and child models with different spatial and temporal scales, which may result in non-trivial sub-model errors in the local areas of interest. Basically, such errors in the child models originate from the deficiency in the coupling methods, as well as from the inadequacy in the spatial and temporal discretizations of the parent and child models. In this study, we investigate the sub-model errors within a generalized one-way coupling scheme given its numerical stability and efficiency, which enables more flexibility in choosing sub-models. To couple the models at different scales, the head solution at parent scale is delivered downward onto the child boundary nodes by means of the spatial and temporal head interpolation approaches. The efficiency of the coupling model is improved either by refining the grid or time step size in the parent and child models, or by carefully locating the sub-model boundary nodes. The temporal truncation errors in the sub-models can be significantly reduced by the adaptive local time-stepping scheme. The generalized one-way coupling scheme is promising to handle the multi-scale groundwater flow problems with complex stresses and heterogeneity.

A two-stage method for microcalcification cluster segmentation in mammography by deformable models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arikidis, N.; Kazantzi, A.; Skiadopoulos, S.

Purpose: Segmentation of microcalcification (MC) clusters in x-ray mammography is a difficult task for radiologists. Accurate segmentation is prerequisite for quantitative image analysis of MC clusters and subsequent feature extraction and classification in computer-aided diagnosis schemes. Methods: In this study, a two-stage semiautomated segmentation method of MC clusters is investigated. The first stage is targeted to accurate and time efficient segmentation of the majority of the particles of a MC cluster, by means of a level set method. The second stage is targeted to shape refinement of selected individual MCs, by means of an active contour model. Both methods aremore » applied in the framework of a rich scale-space representation, provided by the wavelet transform at integer scales. Segmentation reliability of the proposed method in terms of inter and intraobserver agreements was evaluated in a case sample of 80 MC clusters originating from the digital database for screening mammography, corresponding to 4 morphology types (punctate: 22, fine linear branching: 16, pleomorphic: 18, and amorphous: 24) of MC clusters, assessing radiologists’ segmentations quantitatively by two distance metrics (Hausdorff distance—HDIST{sub cluster}, average of minimum distance—AMINDIST{sub cluster}) and the area overlap measure (AOM{sub cluster}). The effect of the proposed segmentation method on MC cluster characterization accuracy was evaluated in a case sample of 162 pleomorphic MC clusters (72 malignant and 90 benign). Ten MC cluster features, targeted to capture morphologic properties of individual MCs in a cluster (area, major length, perimeter, compactness, and spread), were extracted and a correlation-based feature selection method yielded a feature subset to feed in a support vector machine classifier. Classification performance of the MC cluster features was estimated by means of the area under receiver operating characteristic curve (Az ± Standard Error) utilizing tenfold cross-validation methodology. A previously developed B-spline active rays segmentation method was also considered for comparison purposes. Results: Interobserver and intraobserver segmentation agreements (median and [25%, 75%] quartile range) were substantial with respect to the distance metrics HDIST{sub cluster} (2.3 [1.8, 2.9] and 2.5 [2.1, 3.2] pixels) and AMINDIST{sub cluster} (0.8 [0.6, 1.0] and 1.0 [0.8, 1.2] pixels), while moderate with respect to AOM{sub cluster} (0.64 [0.55, 0.71] and 0.59 [0.52, 0.66]). The proposed segmentation method outperformed (0.80 ± 0.04) statistically significantly (Mann-Whitney U-test, p < 0.05) the B-spline active rays segmentation method (0.69 ± 0.04), suggesting the significance of the proposed semiautomated method. Conclusions: Results indicate a reliable semiautomated segmentation method for MC clusters offered by deformable models, which could be utilized in MC cluster quantitative image analysis.« less

SChloro: directing Viridiplantae proteins to six chloroplastic sub-compartments.

PubMed

Savojardo, Castrense; Martelli, Pier Luigi; Fariselli, Piero; Casadio, Rita

2017-02-01

Chloroplasts are organelles found in plants and involved in several important cell processes. Similarly to other compartments in the cell, chloroplasts have an internal structure comprising several sub-compartments, where different proteins are targeted to perform their functions. Given the relation between protein function and localization, the availability of effective computational tools to predict protein sub-organelle localizations is crucial for large-scale functional studies. In this paper we present SChloro, a novel machine-learning approach to predict protein sub-chloroplastic localization, based on targeting signal detection and membrane protein information. The proposed approach performs multi-label predictions discriminating six chloroplastic sub-compartments that include inner membrane, outer membrane, stroma, thylakoid lumen, plastoglobule and thylakoid membrane. In comparative benchmarks, the proposed method outperforms current state-of-the-art methods in both single- and multi-compartment predictions, with an overall multi-label accuracy of 74%. The results demonstrate the relevance of the approach that is eligible as a good candidate for integration into more general large-scale annotation pipelines of protein subcellular localization. The method is available as web server at http://schloro.biocomp.unibo.it gigi@biocomp.unibo.it.

Ship detection using STFT sea background statistical modeling for large-scale oceansat remote sensing image

NASA Astrophysics Data System (ADS)

Wang, Lixia; Pei, Jihong; Xie, Weixin; Liu, Jinyuan

2018-03-01

Large-scale oceansat remote sensing images cover a big area sea surface, which fluctuation can be considered as a non-stationary process. Short-Time Fourier Transform (STFT) is a suitable analysis tool for the time varying nonstationary signal. In this paper, a novel ship detection method using 2-D STFT sea background statistical modeling for large-scale oceansat remote sensing images is proposed. First, the paper divides the large-scale oceansat remote sensing image into small sub-blocks, and 2-D STFT is applied to each sub-block individually. Second, the 2-D STFT spectrum of sub-blocks is studied and the obvious different characteristic between sea background and non-sea background is found. Finally, the statistical model for all valid frequency points in the STFT spectrum of sea background is given, and the ship detection method based on the 2-D STFT spectrum modeling is proposed. The experimental result shows that the proposed algorithm can detect ship targets with high recall rate and low missing rate.

Supersonic Retropropulsion Flight Test Concepts

NASA Technical Reports Server (NTRS)

Post, Ethan A.; Dupzyk, Ian C.; Korzun, Ashley M.; Dyakonov, Artem A.; Tanimoto, Rebekah L.; Edquist, Karl T.

2011-01-01

NASA's Exploration Technology Development and Demonstration Program has proposed plans for a series of three sub-scale flight tests at Earth for supersonic retropropulsion, a candidate decelerator technology for future, high-mass Mars missions. The first flight test in this series is intended to be a proof-of-concept test, demonstrating successful initiation and operation of supersonic retropropulsion at conditions that replicate the relevant physics of the aerodynamic-propulsive interactions expected in flight. Five sub-scale flight test article concepts, each designed for launch on sounding rockets, have been developed in consideration of this proof-of-concept flight test. Commercial, off-the-shelf components are utilized as much as possible in each concept. The design merits of the concepts are compared along with their predicted performance for a baseline trajectory. The results of a packaging study and performance-based trade studies indicate that a sounding rocket is a viable launch platform for this proof-of-concept test of supersonic retropropulsion.

An Integrated Hydrogen Production-CO2 Capture Process from Fossil Fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhicheng Wang

The new technology concept integrates two significant complementary hydrogen production and CO{sub 2}-sequestration approaches that have been developed at Oak Ridge National Laboratory (ORNL) and Clark Atlanta University. The process can convert biomass into hydrogen and char. Hydrogen can be efficiently used for stationary power and mobile applications, or it can be synthesized into Ammonia which can be used for CO{sub 2}-sequestration, while char can be used for making time-release fertilizers (NH{sub 4}HCO{sub 3}) by absorption of CO{sub 2} and other acid gases from exhaust flows. Fertilizers are then used for the growth of biomass back to fields. This projectmore » includes bench scale experiments and pilot scale tests. The Combustion and Emission Lab at Clark Atlanta University has conducted the bench scale experiments. The facility used for pilot scale tests was built in Athens, GA. The overall yield from this process is 7 wt% hydrogen and 32 wt% charcoal/activated carbon of feedstock (peanut shell). The value of co-product activated carbon is about $1.1/GJ and this coproduct reduced the selling price of hydrogen. And the selling price of hydrogen is estimated to be $6.95/GJ. The green house experimental results show that the samples added carbon-fertilizers have effectively growth increase of three different types of plants and improvement ability of keeping fertilizer in soil to avoid the fertilizer leaching with water.« less

Scaling invariance of spherical projectile fragmentation upon high-velocity impact on a thin continuous shield

DOE Office of Scientific and Technical Information (OSTI.GOV)

Myagkov, N. N., E-mail: nn-myagkov@mail.ru

The problem of aluminum projectile fragmentation upon high-velocity impact on a thin aluminum shield is considered. A distinctive feature of this description is that the fragmentation has been numerically simulated using the complete system of equations of deformed solid mechanics by a method of smoothed particle hydrodynamics in three-dimensional setting. The transition from damage to fragmentation is analyzed and scaling relations are derived in terms of the impact velocity (V), ratio of shield thickness to projectile diameter (h/D), and ultimate strength (σ{sub p}) in the criterion of projectile and shield fracture. Analysis shows that the critical impact velocity V{sub c}more » (separating the damage and fragmentation regions) is a power function of σ{sub p} and h/D. In the supercritical region (V > V{sub c}), the weight-average fragment mass asymptotically tends to a power function of the impact velocity with exponent independent of h/D and σ{sub p}. Mean cumulative fragment mass distributions at the critical point are scale-invariant with respect to parameters h/D and σ{sub p}. Average masses of the largest fragments are also scale-invariant at V > V{sub c}, but only with respect to variable parameter σ{sub p}.« less

Validation of the Spanish Short Self-Regulation Questionnaire (SSSRQ) through Rasch Analysis.

PubMed

Garzón Umerenkova, Angélica; de la Fuente Arias, Jesús; Martínez-Vicente, José Manuel; Zapata Sevillano, Lucía; Pichardo, Mari Carmen; García-Berbén, Ana Belén

2017-01-01

Background: The aim of the study was to psychometrically characterize the Spanish Short Self-Regulation Questionnaire (SSSRQ) through Rasch analysis. Materials and Methods: 831 Spaniard university students (262 men), between 17 and 39 years of age and ranging from the first to the 5th year of studies, completed the SSSRQ questionnaire. Confirmatory factor analysis (CFA) was carried out in order to establish structural adequacy. Afterward, by means of the Rasch model, a study of each sub scale was conducted to test for dimensionality, fit of the sample questions, functionality of the response categories, reliability and estimation of Differential Item Functioning by gender and course. Results: The four sub-scales comply with the unidimensionality criteria, the questions are in line with the model, the response categories operate properly and the reliability of the sample is acceptable. Nonetheless, the test could benefit from the inclusion of additional items of both high and low difficulty in order to increase construct validity, discrimination and reliability for the respondents. Several items with differences in gender and course were also identified. Discussion: The results evidence the need and adequacy of this complementary psychometric analysis strategy, in relation to the CFA to enhance the instrument.

Validation of the Spanish Short Self-Regulation Questionnaire (SSSRQ) through Rasch Analysis

PubMed Central

Garzón Umerenkova, Angélica; de la Fuente Arias, Jesús; Martínez-Vicente, José Manuel; Zapata Sevillano, Lucía; Pichardo, Mari Carmen; García-Berbén, Ana Belén

2017-01-01

Background: The aim of the study was to psychometrically characterize the Spanish Short Self-Regulation Questionnaire (SSSRQ) through Rasch analysis. Materials and Methods: 831 Spaniard university students (262 men), between 17 and 39 years of age and ranging from the first to the 5th year of studies, completed the SSSRQ questionnaire. Confirmatory factor analysis (CFA) was carried out in order to establish structural adequacy. Afterward, by means of the Rasch model, a study of each sub scale was conducted to test for dimensionality, fit of the sample questions, functionality of the response categories, reliability and estimation of Differential Item Functioning by gender and course. Results: The four sub-scales comply with the unidimensionality criteria, the questions are in line with the model, the response categories operate properly and the reliability of the sample is acceptable. Nonetheless, the test could benefit from the inclusion of additional items of both high and low difficulty in order to increase construct validity, discrimination and reliability for the respondents. Several items with differences in gender and course were also identified. Discussion: The results evidence the need and adequacy of this complementary psychometric analysis strategy, in relation to the CFA to enhance the instrument. PMID:28298898

Development of Molten Corium Using An Exothermic Chemical Reaction for the Molten- Fuel Moderator-Interaction Studies at Chalk River Laboratories

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nitheanandan, T.; Sanderson, D.B.; Kyle, G.

2004-07-01

Atomic Energy of Canada Limited (AECL) has partnered with Argonne National Laboratory to develop a corium thermite prototypical of Candu material and test the concept of ejecting {approx}25 kg of the molten material from a pressure tube with a driving pressure of 10 MPa. This development program has been completed and the technology transferred to AECL. Preparation for the molten-fuel moderator-interaction tests at AECL's Chalk River Laboratories is well underway. A mixture of 0.582 U/0.077 U{sub 3}O{sub 8}/0.151 Zr/0.19 CrO{sub 3} (wt%) as reactant chemicals has been demonstrated to produce a corium consisting of 0.73 UO{sub 2}/0.11 Zr/0.06 ZrO{sub 2}/0.10more » Cr (wt%) at {approx}2400 deg. C. This is comparable to the target Candu specific corium of 0.9 UO{sub 2}/0.1 Zr (wt%), with limited oxidation. The peak melt temperature was confirmed from small-scale thermitic reaction tests. Several small-scale tests were completed to qualify the thermite to ensure operational safety and a quantifiable experimental outcome. The proposed molten-fuel moderator-interaction experiments at Chalk River Laboratories will consist of heating the thermite mixture inside a 1.14-m long insulated pressure tube. Once the molten material has reached the desired temperature of {approx}2400 deg. C, the pressure inside the tube will be raised to about 10 MPa, and the pressure tube will fail at a pre-machined flaw, ejecting the molten material into the surrounding tank of water. The test apparatus, instrumentation, data acquisition and control systems have been assembled, and a series of successful commissioning tests have been completed. (authors)« less

Amine enriched solid sorbents for carbon dioxide capture

DOEpatents

Gray, McMahan L.; Soong, Yee; Champagne, Kenneth J.

2003-04-15

A new method for making low-cost CO.sub.2 sorbents that can be used in large-scale gas-solid processes. The new method entails treating a solid substrate with acid or base and simultaneous or subsequent treatment with a substituted amine salt. The method eliminates the need for organic solvents and polymeric materials for the preparation of CO.sub.2 capture systems.

Large scale synthesis of nanostructured zirconia-based compounds from freeze-dried precursors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gomez, A.; Villanueva, R.; Vie, D.

2013-01-15

Nanocrystalline zirconia powders have been obtained at the multigram scale by thermal decomposition of precursors resulting from the freeze-drying of aqueous acetic solutions. This technique has equally made possible to synthesize a variety of nanostructured yttria or scandia doped zirconia compositions. SEM images, as well as the analysis of the XRD patterns, show the nanoparticulated character of those solids obtained at low temperature, with typical particle size in the 10-15 nm range when prepared at 673 K. The presence of the monoclinic, the tetragonal or both phases depends on the temperature of the thermal treatment, the doping concentration and themore » nature of the dopant. In addition, Rietveld refinement of the XRD profiles of selected samples allows detecting the coexistence of the tetragonal and the cubic phases for high doping concentration and high thermal treatment temperatures. Raman experiments suggest the presence of both phases also at relatively low treatment temperatures. - Graphical abstract: Zr{sub 1-x}A{sub x}O{sub 2-x/2} (A=Y, Sc; 0{<=}x{<=}0.12) solid solutions have been prepared as nanostructured powders by thermal decomposition of precursors obtained by freeze-drying, and this synthetic procedure has been scaled up to the 100 g scale. Highlights: Black-Right-Pointing-Pointer Zr{sub 1-x}A{sub x}O{sub 2-x/2} (A=Y, Sc; 0{<=}x{<=}0.12) solid solutions have been prepared as nanostructured powders. Black-Right-Pointing-Pointer The synthetic method involves the thermal decomposition of precursors obtained by freeze-drying. Black-Right-Pointing-Pointer The temperature of the thermal treatment controls particle sizes. Black-Right-Pointing-Pointer The preparation procedure has been scaled up to the 100 g scale. Black-Right-Pointing-Pointer This method is appropriate for the large-scale industrial preparation of multimetallic systems.« less

LoCuSS: THE MASS DENSITY PROFILE OF MASSIVE GALAXY CLUSTERS AT z = 0.2 {sup ,}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Okabe, Nobuhiro; Umetsu, Keiichi; Smith, Graham P.

We present a stacked weak-lensing analysis of an approximately mass-selected sample of 50 galaxy clusters at 0.15 < z < 0.3, based on observations with Suprime-Cam on the Subaru Telescope. We develop a new method for selecting lensed background galaxies from which we estimate that our sample of red background galaxies suffers just 1% contamination. We detect the stacked tangential shear signal from the full sample of 50 clusters, based on this red sample of background galaxies, at a total signal-to-noise ratio of 32.7. The Navarro-Frenk-White model is an excellent fit to the data, yielding sub-10% statistical precision on massmore » and concentration: M{sub vir}=7.19{sup +0.53}{sub -0.50} Multiplication-Sign 10{sup 14} h{sup -1} M{sub sun}, c{sub vir}=5.41{sup +0.49}{sub -0.45} (c{sub 200}=4.22{sup +0.40}{sub -0.36}). Tests of a range of possible systematic errors, including shear calibration and stacking-related issues, indicate that they are subdominant to the statistical errors. The concentration parameter obtained from stacking our approximately mass-selected cluster sample is broadly in line with theoretical predictions. Moreover, the uncertainty on our measurement is comparable with the differences between the different predictions in the literature. Overall, our results highlight the potential for stacked weak-lensing methods to probe the mean mass density profile of cluster-scale dark matter halos with upcoming surveys, including Hyper-Suprime-Cam, Dark Energy Survey, and KIDS.« less

Data-based discharge extrapolation: estimating annual discharge for a partially gauged large river basin from its small sub-basins

NASA Astrophysics Data System (ADS)

Gong, L.

2013-12-01

Large-scale hydrological models and land surface models are by far the only tools for accessing future water resources in climate change impact studies. Those models estimate discharge with large uncertainties, due to the complex interaction between climate and hydrology, the limited quality and availability of data, as well as model uncertainties. A new purely data-based scale-extrapolation method is proposed, to estimate water resources for a large basin solely from selected small sub-basins, which are typically two-orders-of-magnitude smaller than the large basin. Those small sub-basins contain sufficient information, not only on climate and land surface, but also on hydrological characteristics for the large basin In the Baltic Sea drainage basin, best discharge estimation for the gauged area was achieved with sub-basins that cover 2-4% of the gauged area. There exist multiple sets of sub-basins that resemble the climate and hydrology of the basin equally well. Those multiple sets estimate annual discharge for gauged area consistently well with 5% average error. The scale-extrapolation method is completely data-based; therefore it does not force any modelling error into the prediction. The multiple predictions are expected to bracket the inherent variations and uncertainties of the climate and hydrology of the basin. The method can be applied in both un-gauged basins and un-gauged periods with uncertainty estimation.

Investigation on Composite Throat Insert For Cryogenic Engines

NASA Astrophysics Data System (ADS)

Ayyappan, G.; Tiwari, S. B.; Praveen, RS; Mohankumar, L.; Jathaveda, M.; Ganesh, P.

2017-02-01

Injector element testing is an important step in the development and qualification of the cryogenic rocket engines. For the purpose of characterising the injectors, sub scale chambers are used. In order to assess the performance of the injectors, different configurations of the injectors are tested using a combustion chamber and a convergent-divergent nozzle. Pressure distribution along the wall of the chamber and throat insert is obtained from the CFD analysis and temperature distribution is obtained from thermal analysis. Thermo-structural analysis is carried out for the sub-scale model of throat inert using temperature dependent material properties. For the experiments a sub-scale model of the thrust chamber is realised. Injector element tests are carried out for the studies. The objective of the present study is to investigate the behaviour of different throat inserts, mainly graphite, 2-D Carbon-Carbon(2D C-C), 4-D Carbon-Carbon (4D C-C) and Silica Phenolic (SP), under pressure and thermal load for repeated operation of the engine. Analytical results are compared with the test results. The paper gives the results of theoretical studies and experiments conducted with all the four type of throat material. It is concluded that 2D C-C is superior in terms of throat erosion being the least under specified combustion environment.

Lateral solids dispersion coefficient in large-scale fluidized beds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Daoyin; Chen, Xiaoping

2010-11-15

The design of fuel feed ports in a large-scale fluidized bed combustor depends on the fuel characteristics and lateral solids mixing. However, the reported values of the effective lateral solids dispersion coefficient (D{sub sr}) are scattered in the broad range of 0.0001-0.1 m{sup 2}/s. With the aim of predicting D{sub sr} in wider fluidized beds which is difficult to measure directly or deduce from experimental results in lab-scale facilities, a computational method is proposed. It combines the Eulerian-Granular simulation and fictitious particle tracing technique. The value of D{sub sr} is calculated based on the movement of the tracers. The effectmore » on D{sub sr} of bed width (W) ranging from 0.4 m up to 12.8 m at different levels of superficial gas velocity (U{sub 0}) is investigated. It is found that increasing W whilst maintaining U{sub 0}, D{sub sr} initially increases markedly, then its increase rate declines, and finally it stays around a constant value. The computed values of D{sub sr} are examined quantitatively and compared with a thorough list of the measured D{sub sr} in the literature since 1980s. Agreed with the measurements performed in the pilot-scale fluidized beds, the value of D{sub sr} in wider facilities at higher fluidizing velocities is predicted to be around the order of magnitude of 0.1 m{sup 2}/s, much higher than that in lab-scale beds. Finally, the effect of D{sub sr} on the distribution of fuel particles over the cross section in fluidized beds with the specified layout of feed ports is discussed. (author)« less

LFNet: A Novel Bidirectional Recurrent Convolutional Neural Network for Light-Field Image Super-Resolution.

PubMed

Wang, Yunlong; Liu, Fei; Zhang, Kunbo; Hou, Guangqi; Sun, Zhenan; Tan, Tieniu

2018-09-01

The low spatial resolution of light-field image poses significant difficulties in exploiting its advantage. To mitigate the dependency of accurate depth or disparity information as priors for light-field image super-resolution, we propose an implicitly multi-scale fusion scheme to accumulate contextual information from multiple scales for super-resolution reconstruction. The implicitly multi-scale fusion scheme is then incorporated into bidirectional recurrent convolutional neural network, which aims to iteratively model spatial relations between horizontally or vertically adjacent sub-aperture images of light-field data. Within the network, the recurrent convolutions are modified to be more effective and flexible in modeling the spatial correlations between neighboring views. A horizontal sub-network and a vertical sub-network of the same network structure are ensembled for final outputs via stacked generalization. Experimental results on synthetic and real-world data sets demonstrate that the proposed method outperforms other state-of-the-art methods by a large margin in peak signal-to-noise ratio and gray-scale structural similarity indexes, which also achieves superior quality for human visual systems. Furthermore, the proposed method can enhance the performance of light field applications such as depth estimation.

Thermal stability tests of CFRP sandwich panels for far infrared astronomy

NASA Technical Reports Server (NTRS)

Hoffmann, W. F.; Helwig, G.; Scheulen, D.

1986-01-01

An account is given of fabrication methods and low temperature figure tests for CFRP sandwich panels, in order to ascertain their applicability to ultralightweight 3-m aperture primary mirrors for balloon-borne sub-mm and far-IF telescopes that must maintain a 1-2 micron rms surface figure accuracy at -40 to -50 C. Optical figure measurements on the first two of a series of four 0.5-m test panels, replicated to a spherical surface, show a radius-of-curvature change and astigmatism down to -60 C; this approximately follows the composite's theoretical predictions and implies that material and process control is excellent, so that the large scale changes observed can be compensated for.

Space Launch System Base Heating Test: Sub-Scale Rocket Engine/Motor Design, Development and Performance Analysis

NASA Technical Reports Server (NTRS)

Mehta, Manish; Seaford, Mark; Kovarik, Brian; Dufrene, Aaron; Solly, Nathan; Kirchner, Robert; Engel, Carl D.

2014-01-01

The Space Launch System (SLS) base heating test is broken down into two test programs: (1) Pathfinder and (2) Main Test. The Pathfinder Test Program focuses on the design, development, hot-fire test and performance analyses of the 2% sub-scale SLS core-stage and booster element propulsion systems. The core-stage propulsion system is composed of four gaseous oxygen/hydrogen RS-25D model engines and the booster element is composed of two aluminum-based model solid rocket motors (SRMs). The first section of the paper discusses the motivation and test facility specifications for the test program. The second section briefly investigates the internal flow path of the design. The third section briefly shows the performance of the model RS-25D engines and SRMs for the conducted short duration hot-fire tests. Good agreement is observed based on design prediction analysis and test data. This program is a challenging research and development effort that has not been attempted in 40+ years for a NASA vehicle.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alptekin, Gokhan

The overall objective of the proposed research is to develop a low cost, high capacity CO{sub 2} sorbent and demonstrate its technical and economic viability for pre-combustion CO{sub 2} capture. The specific objectives supporting our research plan were to optimize the chemical structure and physical properties of the sorbent, scale-up its production using high throughput manufacturing equipment and bulk raw materials and then evaluate its performance, first in bench-scale experiments and then in slipstream tests using actual coal-derived synthesis gas. One of the objectives of the laboratory-scale evaluations was to demonstrate the life and durability of the sorbent for overmore » 10,000 cycles and to assess the impact of contaminants (such as sulfur) on its performance. In the field tests, our objective was to demonstrate the operation of the sorbent using actual coal-derived synthesis gas streams generated by air-blown and oxygen-blown commercial and pilot-scale coal gasifiers (the CO{sub 2} partial pressure in these gas streams is significantly different, which directly impacts the operating conditions hence the performance of the sorbent). To support the field demonstration work, TDA collaborated with Phillips 66 and Southern Company to carry out two separate field tests using actual coal-derived synthesis gas at the Wabash River IGCC Power Plant in Terre Haute, IN and the National Carbon Capture Center (NCCC) in Wilsonville, AL. In collaboration with the University of California, Irvine (UCI), a detailed engineering and economic analysis for the new CO{sub 2} capture system was also proposed to be carried out using Aspen PlusTM simulation software, and estimate its effect on the plant efficiency.« less

Finalizing the DTAG: Implementation and Testing of Design Improvements for Reliability and Availability

DTIC Science & Technology

2015-09-30

acoustics and fine scale motion. The success of the Dtag has resulted in an increased demand for the instrument from researchers both within the...sensor blocks sound when the animal is close to the surface. The polyethylene shell was eliminated in the Dtag-3 design to improve acoustic ...into 3 main sub-assemblies (Figure 5): 1) foam sub-assembly, 2) sensor sub-assembly, and 3) Electronics sub-assembly. This separation enables rapid

[Validation of the Cognitive Impairment in Psychiatry (SCIP-S) Screen Scale in Patients with Bipolar Disorder I].

PubMed

Castaño Ramírez, Oscar Mauricio; Martínez Ramírez, Yeferson André; Marulanda Mejía, Felipe; Díaz Cabezas, Ricardo; Valderrama Sánchez, Lenis Alexandra; Varela Cifuentes, Vilma; Aguirre Acevedo, Daniel Camilo

2015-01-01

The Spanish version of the cognitive impairment in psychiatry scale screening scale has been developed as a response to the needs arising in clinical practice during the evaluation of mental illness patients, but the performance is not known in the Colombian population with bipolar disorder I. This paper tries to establish construct validity and stability of the scale in patients with bipolar disorder I in the city of Manizales. Construct validity was estimated by comparing the measurement in two divergent groups, a control group and a group with bipolar disorder I. It was also compared to a Neuropsychological battery measuring the same scale domains. The correlation between each one of the sub-tests of the scale and stability was evaluated through the reliability test-retest in the group with bipolar disorder I. The scale showed discriminatory capacity in cognitive functioning between the control group and the group with bipolar disorder I. The correlation with the neuropsychological battery was estimated by the Spearman test showing results between 0.36 and 0.77, and the correlation between each sub-test of the scale showed correlations between 0.39 and 0.72. Test-retest was measured with the intraclass correlation coefficient (ICC) and their values were between 0.77 and 0.91. The Spanish version of screening scale in the cognitive disorder in psychiatry shows acceptable validity and reliability as a measurement tool in clinical psychiatric practice. Copyright © 2014 Asociación Colombiana de Psiquiatría. Publicado por Elsevier España. All rights reserved.

Combined SO sub x /NO sub x removal and concentration from flue gas through an electrochemical membrane

DOE Office of Scientific and Technical Information (OSTI.GOV)

Winnick, J.

1989-11-01

Electrochemical membrane removal of SO{sub 2} from flue gas and concentration into a salable by-product stream has been achieved. Full-cell tests have verified both the concept and choice of materials compatible with the process gas. Electrodes have been developed, manufactured from a conducting ceramic, La{sub 0.8}Sr{sub 0.2}CoO{sub 3}. Electrochemical cell reactions conform precisely with those discerned in free electrolyte. These reactions are stoichiometric to over 95% SO{sub 2} removal. Oleum by-product generation is likewise totally stoichiometric (100% current efficiency). NO{sub x} removal has been found to occur at the oxidizing electrode. Cell polarization, that is, the achievable current densities atmore » reasonable voltage, is unacceptable with the membranes tested thus far. Future work will focus on identifying a ceramic matrix material and a membrane fabrication technique which yields a membrane with the proper capillarity match with the porous electrodes. This will give the cell the proper polarization performance to permit larger scale endurance tests. 56 figs.« less

Spatiotemporal and Kinematic Parameters Relating to Oriented Gait and Turn Performance in Patients with Chronic Stroke

PubMed Central

Bonnyaud, Céline; Pradon, Didier; Vuillerme, Nicolas; Bensmail, Djamel; Roche, Nicolas

2015-01-01

Background The timed up and go test (TUG) is a functional test which is increasingly used to evaluate patients with stroke. The outcome measured is usually global TUG performance-time. Assessment of spatiotemporal and kinematic parameters during the Oriented gait and Turn sub-tasks of the TUG would provide a better understanding of the mechanisms underlying patients’ performance and therefore may help to guide rehabilitation. The aim of this study was thus to determine the spatiotemporal and kinematic parameters which were most related to the walking and turning sub-tasks of TUG performance in stroke patients. Methods 29 stroke patients carried out the TUG test which was recorded using an optoelectronic system in two conditions: spontaneous and standardized condition (standardized foot position and instructed to turn towards the paretic side). They also underwent a clinical assessment. Stepwise regression was used to determine the parameters most related to Oriented gait and Turn sub-tasks. Relationships between explanatory parameters of Oriented gait and Turn performance and clinical scales were evaluated using Spearman correlations. Results Step length and cadence explained 82% to 95% of the variance for the walking sub-tasks in both conditions. Percentage single support phase and contralateral swing phase (depending on the condition) respectively explained 27% and 56% of the variance during the turning sub-task in the spontaneous and standardized conditions. Discussion and Conclusion Step length, cadence, percentage of paretic single support phase and non-paretic swing phase, as well as dynamic stability were the main parameters related to TUG performance and they should be targeted in rehabilitation. PMID:26091555

Studies of fly ash using thermal analysis techniques

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Hanxu; Shen, Xiang-Zhong; Sisk, B.

1996-12-31

Improved thermoanalytical methods have been developed that are capable of quantitative identification of various components of fly ash from a laboratory-scale fluidized bed combustion system. The thermogravimetric procedure developed can determine quantities of H{sub 2}O, Ca(OH){sub 2}, CaCO{sub 3}, CaSO{sub 4} and carbonaceous matter in fly ash with accuracy comparable to more time-consuming ASTM methods. This procedure is a modification of the Mikhail-Turcotte methods that can accurately analyze bed ash, with higher accuracy regarding the greater amount of carbonaceous matter in fly ash. In addition, in conjunction with FTIR and SEM/EDS analysis, the reduction mechanism of CaSO{sub 4} as CaSO{submore » 4} + 4H{sub 2} = CaS + 4H{sub 2}O has been confirmed in this study. This mechanism is important in analyzing and evaluating sulfur capture in fluidized-bed combustion systems.« less

Emerging Methods in Sub Core-Scale Imaging and Characterization of the Influence of Heterogeneity on Flow in Rocks (Invited)

NASA Astrophysics Data System (ADS)

Benson, S. M.; Hingerl, F.; Pini, R.

2013-12-01

New imaging techniques and approaches are providing unparalleled insight into the influence of sub-core scale heterogeneities on single and multiphase flows. Quantification of sub core-scale porosity, permeability, and even capillary pressure curves at a spatial scale of about 1-10 cubic millimeters is now possible. This scale provides a critical link in the continuum of spatial scales needed to link pore-scale processes to core-scale and field scale flow and transport. Data from such studies can be used to directly test the veracity of models for flow and transport in heterogeneous rocks, provide data for multi-stage upscaling, and reveal insights about physical/chemical processes heretofore neglected. Here we present data from three emerging techniques capable of imaging and quantifying transport properties and phenomena at the sub-core scale: magnetic resonance imaging (MRI); positron emission tomography (PET); and X-Ray CT scanning. Direct imaging of spatially resolved fluid velocities and porosity is possible with MRI (Romanenko et al., 2012). These data can be inverted to provide permeability and porosity maps at a spatial scale of ~10 cubic millimeter. PET imaging can be used to track movement of a radioactive tracer through a rock and simultaneously measure effluent tracer concentrations at a similar resolution (Boutchko et al., 2012). X-ray CT scanning of multiphase flow experiments can be used to measure capillary pressure curves and through scaling relationships, to calculate permeability at a scale of about 1 cubic millimeters(Krause et al., 2011; Pini et al., 2013). Strengths and shortcomings of these techniques are discussed--along with the benefits of combining them. Together these techniques provide a new platform from which to probe more deeply the ubiquitous influence of heterogeneity on subsurface flow and transport processes, and ultimately improve predictions of subsurface transport. Boutchk et al., 2012. Imaging and modeling of flow in porous media using clinical nuclear emission tomography systems and computational fluid dynamics. Journal of Applied geophysics, 76, 74-81. Krause, M.H., J.C. Perrin, and S.M. Benson, 2011. Modeling permeability distributions in a sandstone core for history matching core flood experiments, SPE Journal, 16, 768-777. Pini R. and Benson S., Characterization and scaling of meso-scale heterogeneities in sandstones. Geophysical Research Letters, 2013, 40. Romanenko, K., and Balscom, Permeability mapping in naturally heterogeneous sandstone cores with magnetization prepared SPRITE, 2012, 58, 3916-3926.

A comparison of muscle strength and endurance, exercise capacity, fatigue perception and quality of life in patients with chronic obstructive pulmonary disease and healthy subjects: a cross-sectional study

PubMed Central

2014-01-01

Background Chronic obstructive pulmonary disease (COPD) has significant systemic effects that substantially impact quality of life and survival. The purpose of this study was to assess and compare peripheral muscle strength and endurance, exercise capacity, fatigue perception and quality of life between patients with COPD and healthy subjects. Methods Twenty COPD patients (mean FEV1 49.3 ± 19.2%) and 20 healthy subjects were included in the study. Pulmonary function testing and six-minute walk test (6MWT) were performed. Peripheral muscle strength was measured with a hand-held dynamometer, peripheral muscle endurance was evaluated with sit-ups, squats and modified push-ups tests. Fatigue perception was assessed using the Fatigue Impact Scale (FIS) and Fatigue Severity Scale (FSS). General quality of life was determined with the Nottingham Health Profile (NHP), and cough-specific quality of life was evaluated with the Leicester Cough Questionnaire (LCQ). Results Pulmonary functions, strength of shoulder abductor and flexor muscles, numbers of sit-ups and squats, 6MWT distance and 6MWT% were significantly lower in COPD patients than in healthy subjects (p < 0.05). FIS psychosocial sub-dimension and total scores, NHP scores for all sub-dimensions except pain sub-dimension of the COPD group were significantly higher than those of healthy subjects (p < 0.05). The LCQ physical, psychological and social sub-dimensions and total scores were significantly lower in COPD patients than in healthy subjects (p < 0.05). Conclusions Pulmonary functions, peripheral muscle strength and endurance, exercise capacity and quality of life were adversely affected in patients with COPD. There are greater effect of fatigue on psychosocial functioning and general daily life activities and effect of cough on the quality of life in patients with COPD. This study supports the idea that COPD patients must be evaluated in a comprehensive manner for planning pulmonary rehabilitation programs. PMID:24468029

Power spectrum, correlation function, and tests for luminosity bias in the CfA redshift survey

NASA Technical Reports Server (NTRS)

Park, Changbom; Vogeley, Michael S.; Geller, Margaret J.; Huchra, John P.

1994-01-01

We describe and apply a method for directly computing the power spectrum for the galaxy distribution in the extension of the Center for Astrophysics Redshift Survey. Tests show that our technique accurately reproduces the true power spectrum for k greater than 0.03 h Mpc(exp -1). The dense sampling and large spatial coverage of this survey allow accurate measurement of the redshift-space power spectrum on scales from 5 to approximately 200 h(exp -1) Mpc. The power spectrum has slope n approximately equal -2.1 on small scales (lambda less than or equal 25 h(exp -1) Mpc) and n approximately -1.1 on scales 30 less than lambda less than 120 h(exp -1) Mpc. On larger scales the power spectrum flattens somewhat, but we do not detect a turnover. Comparison with N-body simulations of cosmological models shows that an unbiased, open universe CDM model (OMEGA h = 0.2) and a nonzero cosmological constant (CDM) model (OMEGA h = 0.24, lambda(sub zero) = 0.6, b = 1.3) match the CfA power spectrum over the wavelength range we explore. The standard biased CDM model (OMEGA h = 0.5, b = 1.5) fails (99% significance level) because it has insufficient power on scales lambda greater than 30 h(exp -1) Mpc. Biased CDM with a normalization that matches the Cosmic Microwave Background (CMB) anisotropy (OMEGA h = 0.5, b = 1.4, sigma(sub 8) (mass) = 1) has too much power on small scales to match the observed galaxy power spectrum. This model with b = 1 matches both Cosmic Background Explorer Satellite (COBE) and the small-scale power spect rum but has insufficient power on scales lambda approximately 100 h(exp -1) Mpc. We derive a formula for the effect of small-scale peculiar velocities on the power spectrum and combine this formula with the linear-regime amplification described by Kaiser to compute an estimate of the real-space power spectrum. Two tests reveal luminosity bias in the galaxy distribution: First, the amplitude of the pwer spectrum is approximately 40% larger for the brightest 50% of galaxies in volume-limited samples that have M(sub lim) greater than M*. This bias in the power spectrum is independent of scale, consistent with the peaks-bias paradigm for galaxy formation. Second, the distribution of local density around galaxies shows that regions of moderate and high density contain both very bright (M less than M* = -19.2 + 5 log h) and fainter galaxies, but that voids preferentially harbor fainter galaxies (approximately 2 sigma significance level).

Apparatus and method for defect testing of integrated circuits

DOEpatents

Cole, Jr., Edward I.; Soden, Jerry M.

2000-01-01

An apparatus and method for defect and failure-mechanism testing of integrated circuits (ICs) is disclosed. The apparatus provides an operating voltage, V.sub.DD, to an IC under test and measures a transient voltage component, V.sub.DDT, signal that is produced in response to switching transients that occur as test vectors are provided as inputs to the IC. The amplitude or time delay of the V.sub.DDT signal can be used to distinguish between defective and defect-free (i.e. known good) ICs. The V.sub.DDT signal is measured with a transient digitizer, a digital oscilloscope, or with an IC tester that is also used to input the test vectors to the IC. The present invention has applications for IC process development, for the testing of ICs during manufacture, and for qualifying ICs for reliability.

Novel density functional methodology for the computation of accurate electronic and thermodynamic properties of molecular systems and improved long-range behavior

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kafafi, S.A.

1998-12-10

A novel general purpose density functional methodology for the computation of accurate electronic and thermodynamic properties of molecules and improved long-range behavior is reported. Assuming the separability of the exchange (E{sub x}) and correlation (E{sub c}) contributions to the total exchange-correlation energy functional (E{sub xc}), the E{sub x} term consists of a hybrid mixture of 37.5% Hartree-Fock exchange and the appropriate local spin density exchange using the adiabatic connection formula. He demonstrated that E{sub x} and its corresponding potential V{sub x} [=dE{sub x}/d{rho}(r)] have the proper asymptotic limits at r = 0 and r {r_arrow} {infinity}, E{sub c} consists ofmore » the Vosko, Wilk, and Nusair formula for the free-electron gas correlation energy and a generalized gradient approximation term with one adjustable parameter. V{sub c} [=dE{sub c}/d{rho}(r)] was shown to obey the r {r_arrow} {infinity} limit of the corresponding potential derived from exact atomic exchange-correlation computations; namely, V{sub c} is proportional to r{sup {minus}4}. Most importantly, he demonstrated that, at r values where dispersion forces are operating, V{sub c} is proportional to 1/r{sup n} (n = 4, 6, 8, {hor_ellipsis}). The reported method was denoted by K2-BVWN because it used two adjustable parameters in its formulation. The K2-BVWN scheme scales as N{sup 3}, where N is the number of basis functions, compared to {approximately}N{sup 7} for Gaussian-2 (G2) ab initio theory and related methods, {approximately}N{sup 5} for Barone`s mPW1,3PW, and {approximately}N{sup 4} for Becke`s three-parameter density functional approaches. The G2 data set complemented by the reported molecular systems investigated in this work was recommended as a critical test for evaluating novel ab initio and density functional methodologies. The K2-BVWN method has been implemented in the Gaussian series of programs.« less

FCI experiments in the corium/water system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huhtiniemi, I.; Hohmann, H.; Magallon, D.

The KROTOS fuel coolant interaction (FCI) tests aim at providing benchmark data to examine the effect of fuel/coolant initial conditions and mixing on explosion energetics. Experiments, fundamental in nature, are performed in well-controlled geometries and are complementary to the FARO large scale tests. Recently, a new test series was started using 3 kg of prototypical core material (80 w/o UO{sub 2}, 20 w/o ZrO{sub 2}) which was poured into a water column of {le} 1.25 m in height (95 mm and 200 mm in diameter) under 0.1 MPa ambient pressure. Four tests have been performed in the test section ofmore » 95 mm in diameter (ID) with different subcooling levels (10-80K) and with and without an external trigger. Additionally, one test has been performed with a test section of 200 mm in diameter (ID) and with an external trigger. No spontaneous or triggered energetic FCIs (steam explosions) have been observed in these corium tests. This is in sharp contrast with the steam explosions observed in the previously reported Al{sub 2}O{sub 3} test series which had the same initial conditions of ambient pressure and subcooling. The post-test analysis of the corium experiments indicated that strong vaporisation at the melt/water contact led to a partial expulsion of the melt from the test section into the pressure vessel. In order to avoid this and to obtain a good penetration and premixing os the corium melt, an additional test has been performed with a larger diameter test section. In all the UO{sub 2}-ZrO{sub 2} tests an efficient quenching process (0.7-1.2 MW/kg-melt) with total fuel fragmentation (mass mean diameter 1.4-2.5 mm) was observed. Results from Al{sub 2}O{sub 3} tests under the same initial conditions are also presented for further confirmation of the observed differences in behaviour between Al{sub 2}O{sub 3} and UO{sub 2}-ZrO{sub 2} melts.« less

Nonlinear structure formation in flat cosmological models

NASA Technical Reports Server (NTRS)

Martel, Hugo

1995-01-01

This paper describes the formation of nonlinear structure in flat (zero curvature) Friedmann cosmological models. We consider models with two components: the usual nonrelativistic component that evolves under gravity and eventually forms the large-scale structure of the universe, and a uniform dark matter component that does not clump under gravity, and whose energy density varies with the scale factor a(t) like a(t)(sup -n), where n is a free parameter. Each model is characterized by two parameters: the exponent n and the present density parameter Omega(sub 0) of the nonrelativistic component. The linear perturbation equations are derived and solved for these models, for the three different cases n = 3, n is greater than 3, and n is less than 3. The case n = 3 is relevant to model with massive neutrinos. The presence of the uniform component strongly reduces the growth of the perturbation compared with the Einstein-de Sitter model. We show that the Meszaros effect (suppression of growth at high redshift) holds not only for n = 4, radiation-dominated models, but for all models with n is greater than 3. This essentially rules out any such model. For the case n is less than 3, we numerically integrate the perturbation equations from the big bang to the present, for 620 different models with various values of Omega(sub 0) and n. Using these solutions, we show that the function f(Omega(sub 0), n) = (a/delta(sub +))d(delta)(sub +)/da, which enters in the relationship between the present density contrast delta(sub 0) and peculiar velocity field u(sub 0) is essentially independent of n. We derive approximate solutions for the second-order perturbation equations. These second-order solutions are tested against the exact solutions and the Zel'dovich approximation for spherically symmetric perturbations in the marginally nonlinear regime (the absolute value of delta is less than or approximately 1). The second-order and Zel'dovich solutions have comparable accuracy, significantly higher than the accuracy of the linear solutions. We then investigate the dependence of the delta(sub 0) - u(sub 0) relationship upon the value of n in the nonlinear regime using the second-order solutions for marginally nonlinear, general perturbations, and the exact solutions for strongly nonlinear, spherically symmetric perturbations. In both cases, we find that the delta(sub 0) - u(sub 0) relationship remains independent of n. We speculate that this result extends to strongly nonlinear, general perturbations as well. This eliminates any hope to determine the presence of the uniform component or the value of n using dynamical methods. Finally, we compute the nonlinear evolution of the skewness of the distribution of values of delta, assuming Gaussian initial conditions. We find that the skewness is not only independent of n, but also of Omega(sub 0). Thus the skewness cannot be used to discriminate among various models with Gaussian initial conditions. However, it can be used for testing the Gaussianity of the initial conditions themselves. We conclude that the uniform component leaves no observable signature in the present large-scale structure of the universe. To determine its presence and nature, we must investigate the relationship between the past and present universe, using redshift-dependent tests.

Nondestructive measurement of the refractive index distribution of a glass molded lens by two-wavelength wavefronts.

PubMed

Sugimoto, Tomohiro

2016-10-01

This paper presents a nondestructive and non-exact-index-matching method for measuring the refractive index distribution of a glass molded lens with high refractivity. The method measures two-wavelength wavefronts of a test lens immersed in a liquid with a refractive index dispersion different from that of the test lens and calculates the refractive index distribution by eliminating the refractive index distribution error caused by the shape error of the test lens. The estimated uncertainties of the refractive index distributions of test lenses with n_d≈1.77 and n_d≈1.85 were 1.9×10^-5  RMS and 2.4×10^-5  RMS, respectively. I validated the proposed method by evaluating the agreement between the estimated uncertainties and experimental values.

Millimeter-scale epileptiform spike propagation patterns and their relationship to seizures

PubMed Central

Vanleer, Ann C; Blanco, Justin A; Wagenaar, Joost B; Viventi, Jonathan; Contreras, Diego; Litt, Brian

2016-01-01

Objective Current mapping of epileptic networks in patients prior to epilepsy surgery utilizes electrode arrays with sparse spatial sampling (∼1.0 cm inter-electrode spacing). Recent research demonstrates that sub-millimeter, cortical-column-scale domains have a role in seizure generation that may be clinically significant. We use high-resolution, active, flexible surface electrode arrays with 500 μm inter-electrode spacing to explore epileptiform local field potential spike propagation patterns in two dimensions recorded from subdural micro-electrocorticographic signals in vivo in cat. In this study, we aimed to develop methods to quantitatively characterize the spatiotemporal dynamics of epileptiform activity at high-resolution. Approach We topically administered a GABA-antagonist, picrotoxin, to induce acute neocortical epileptiform activity leading up to discrete electrographic seizures. We extracted features from local field potential spikes to characterize spatiotemporal patterns in these events. We then tested the hypothesis that two dimensional spike patterns during seizures were different from those between seizures. Main results We showed that spatially correlated events can be used to distinguish ictal versus interictal spikes. Significance We conclude that sub-millimeter-scale spatiotemporal spike patterns reveal network dynamics that are invisible to standard clinical recordings and contain information related to seizure-state. PMID:26859260

Millimeter-scale epileptiform spike propagation patterns and their relationship to seizures

NASA Astrophysics Data System (ADS)

Vanleer, Ann C.; Blanco, Justin A.; Wagenaar, Joost B.; Viventi, Jonathan; Contreras, Diego; Litt, Brian

2016-04-01

Objective. Current mapping of epileptic networks in patients prior to epilepsy surgery utilizes electrode arrays with sparse spatial sampling (∼1.0 cm inter-electrode spacing). Recent research demonstrates that sub-millimeter, cortical-column-scale domains have a role in seizure generation that may be clinically significant. We use high-resolution, active, flexible surface electrode arrays with 500 μm inter-electrode spacing to explore epileptiform local field potential (LFP) spike propagation patterns in two dimensions recorded from subdural micro-electrocorticographic signals in vivo in cat. In this study, we aimed to develop methods to quantitatively characterize the spatiotemporal dynamics of epileptiform activity at high-resolution. Approach. We topically administered a GABA-antagonist, picrotoxin, to induce acute neocortical epileptiform activity leading up to discrete electrographic seizures. We extracted features from LFP spikes to characterize spatiotemporal patterns in these events. We then tested the hypothesis that two-dimensional spike patterns during seizures were different from those between seizures. Main results. We showed that spatially correlated events can be used to distinguish ictal versus interictal spikes. Significance. We conclude that sub-millimeter-scale spatiotemporal spike patterns reveal network dynamics that are invisible to standard clinical recordings and contain information related to seizure-state.

Detecting anomalies in CMB maps: a new method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neelakanta, Jayanth T., E-mail: jayanthtn@gmail.com

2015-10-01

Ever since WMAP announced its first results, different analyses have shown that there is weak evidence for several large-scale anomalies in the CMB data. While the evidence for each anomaly appears to be weak, the fact that there are multiple seemingly unrelated anomalies makes it difficult to account for them via a single statistical fluke. So, one is led to considering a combination of these anomalies. But, if we ''hand-pick'' the anomalies (test statistics) to consider, we are making an a posteriori choice. In this article, we propose two statistics that do not suffer from this problem. The statistics aremore » linear and quadratic combinations of the a{sub ℓ m}'s with random co-efficients, and they test the null hypothesis that the a{sub ℓ m}'s are independent, normally-distributed, zero-mean random variables with an m-independent variance. The motivation for considering multiple modes is this: because most physical models that lead to large-scale anomalies result in coupling multiple ℓ and m modes, the ''coherence'' of this coupling should get enhanced if a combination of different modes is considered. In this sense, the statistics are thus much more generic than those that have been hitherto considered in literature. Using fiducial data, we demonstrate that the method works and discuss how it can be used with actual CMB data to make quite general statements about the incompatibility of the data with the null hypothesis.« less

A Method for Localizing Energy Dissipation in Blazars Using Fermi Variability

NASA Technical Reports Server (NTRS)

Dotson, Amanda; Georganopoulos, Markos; Kazanas, Demosthenes; Perlman, Eric S.

2013-01-01

The distance of the Fermi-detected blazar gamma-ray emission site from the supermassive black hole is a matter of active debate. Here we present a method for testing if the GeV emission of powerful blazars is produced within the sub-pc scale broad line region (BLR) or farther out in the pc-scale molecular torus (MT) environment. If the GeV emission takes place within the BLR, the inverse Compton (IC) scattering of the BLR ultraviolet (UV) seed photons that produces the gamma-rays takes place at the onset of the Klein-Nishina regime. This causes the electron cooling time to become practically energy independent and the variation of the gamma-ray emission to be almost achromatic. If on the other hand the -ray emission is produced farther out in the pc-scale MT, the IC scattering of the infrared (IR) MT seed photons that produces the gamma-rays takes place in the Thomson regime, resulting to energy-dependent electron cooling times, manifested as faster cooling times for higher Fermi energies. We demonstrate these characteristics and discuss the applicability and limitations of our method.

The analysis of reliability and validity of the IT-MAIS, MAIS and MUSS.

PubMed

Zhong, Yan; Xu, Tianqiu; Dong, Ruijuan; Lyu, Jing; Liu, Bo; Chen, Xueqing

2017-05-01

The aim of this study was to investigate the reliability and validity of the Infant-toddler Meaningful Auditory Integration Scale (IT-MAIS), Meaningful Auditory Integration Scale (MAIS), and Meaningful Use of Speech Scale (MUSS). IT-MAIS, MAIS and MUSS were divided into 3 sub dimensions. 300 children with cochlear implants (CI) were included in the investigation. To assess test-retest reliability of these questionnaires, 30 children were selected randomly to be evaluated at a two-week interval indicated that there were no significant changes between test and retest. Furthermore random test analysis by different evaluators was also administered to 30 users. Reliability test: Test-retest reliability of the three scales was proved to be satisfactory. All domains had correlation coefficients that exceeded 0.750(P < 0.01). The Cronbach's α of the three scales and their three domains were greater than 0.700. Reliability between evaluators of the three scales were considered to be satisfactory. All domains had correlation coefficients that exceeded 0.750(P < 0.01). Validity test: The evaluation of content validity by expert review showed the questionnaire had good content validity; The correlation coefficients between the overall scores of the three scales and their three domains were 0.699-0.978(P < 0.01). There were correlations among the three sub-domains but the strength of the correlations was relatively low. There was certain construct validity. IT-MAIS, MAIS, MUSS scales have good reliability and validity, and can be used to measure the outcome for children with cochlear implants hearing and speech evaluation. Copyright © 2017 Elsevier B.V. All rights reserved.

The effect of pH on the corrosion behavior of intermetallic compounds Ni{sub 3}(Si,Ti) and Ni{sub 3}(Si,Ti) + 2Mo in sodium chloride solutions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Priyotomo, Gadang, E-mail: gada001@lipi.go.id; Nuraini, Lutviasari, E-mail: Lutviasari@gmail.com; Kaneno, Yasuyuki, E-mail: kaneno@mtr.osakafu-u.ac.id

The corrosion behavior of the intermetallic compounds, Ni{sub 3}(Si,Ti) (L1{sub 2}: single phase) and Ni{sub 3}(Si,Ti) + 2Mo (L1{sub 2} and (L12 + Ni{sub ss}) mixture region), has been investigated using an immersion test, electrochemical method and surface analytical method (SEM; scanning electron microscope and EDAX: Energy Dispersive X-ray) in 0.5 kmol/m{sup 3} NaCl solutions at various pH. The corrosion behavior of nickel alloy C-276 was studied under the same experimental conditions as a reference. It was found that the uniform attack was observed on Ni{sub 3}(Si,Ti) for the immersion test at lower pH, while the pitting attack was observedmore » on this compound for this test at neutral solution. Furthermore, Ni{sub 3}(Si,Ti)+2Mo had the preferential dissolution of L1{sub 2} compared to (L1{sub 2} + Ni{sub ss}) mixture region at lower pH, while pitting attack occurred in (L1{sub 2} + Ni{sub ss}) mixture region at neutral solution. For both intermetallic compounds, the magnitude of pitting and uniform attack decrease with increasing pH of solutions. From the immersion test and polarization curves, the corrosion resistance of Ni{sub 3}(Si,Ti)+2Mo is lower than that of Ni{sub 3}(Si,Ti), while the nickel alloy C-276 is the highest one at various pH of solutions. On the other hand, in the lower pH of solutions, the corrosion resistance of tested materials decreased significantly compared to those in neutral and higher pH of solutions.« less

A STATISTICAL STUDY OF THE SOLAR WIND TURBULENCE AT ION KINETIC SCALES USING THE K-FILTERING TECHNIQUE AND CLUSTER DATA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roberts, O. W.; Li, X.; Jeska, L., E-mail: o.wyn.roberts@gmail.com, E-mail: xxl@aber.ac.uk

2015-03-20

Plasma turbulence at ion kinetic scales in the solar wind is investigated using the multi-point magnetometer data from the Cluster spacecraft. By applying the k-filtering method, we are able to estimate the full three-dimensional power spectral density P(ω{sub sc}, k) at a certain spacecraft frequency ω{sub sc} in wavevector (k) space. By using the wavevector at the maximum power in P(ω{sub sc}, k) at each sampling frequency ω{sub sc} and the Doppler shifted frequency ω{sub pla} in the solar wind frame, the dispersion plot ω{sub pla} = ω{sub pla}(k) is found. Previous studies have been limited to very few intervalsmore » and have been hampered by large errors, which motivates a statistical study of 52 intervals of solar wind. We find that the turbulence is predominantly highly oblique to the magnetic field k >> k {sub ∥}, and propagates slowly in the plasma frame with most points having frequencies smaller than the proton gyrofrequency ω{sub pla} < Ω{sub p}. Weak agreement is found that turbulence at the ion kinetic scales consists of kinetic Alfvén waves and coherent structures advected with plasma bulk velocity plus some minor more compressible components. The results suggest that anti-sunward and sunward propagating magnetic fluctuations are of similar nature in both the fast and slow solar wind at ion kinetic scales. The fast wind has significantly more anti-sunward flux than sunward flux and the slow wind appears to be more balanced.« less

Large-scale self-assembly of uniform submicron silver sulfide material driven by precise pressure control

NASA Astrophysics Data System (ADS)

Qi, Juanjuan; Chen, Ke; Zhang, Shuhao; Yang, Yun; Guo, Lin; Yang, Shihe

2017-03-01

The controllable self-assembly of nanosized building blocks into larger specific structures can provide an efficient method of synthesizing novel materials with excellent properties. The self-assembly of nanocrystals by assisted means is becoming an extremely active area of research, because it provides a method of producing large-scale advanced functional materials with potential applications in the areas of energy, electronics, optics, and biologics. In this study, we applied an efficient strategy, namely, the use of ‘pressure control’ to the assembly of silver sulfide (Ag2S) nanospheres with a diameter of approximately 33 nm into large-scale, uniform Ag2S sub-microspheres with a size of about 0.33 μm. More importantly, this strategy realizes the online control of the overall reaction system, including the pressure, reaction time, and temperature, and could also be used to easily fabricate other functional materials on an industrial scale. Moreover, the thermodynamics and kinetics parameters for the thermal decomposition of silver diethyldithiocarbamate (Ag(DDTC)) are also investigated to explore the formation mechanism of the Ag2S nanosized building blocks which can be assembled into uniform sub-micron scale architecture. As a method of producing sub-micron Ag2S particles by means of the pressure-controlled self-assembly of nanoparticles, we foresee this strategy being an efficient and universally applicable option for constructing other new building blocks and assembling novel and large functional micromaterials on an industrial scale.

Distributed weighted least-squares estimation with fast convergence for large-scale systems.

PubMed

Marelli, Damián Edgardo; Fu, Minyue

2015-01-01

In this paper we study a distributed weighted least-squares estimation problem for a large-scale system consisting of a network of interconnected sub-systems. Each sub-system is concerned with a subset of the unknown parameters and has a measurement linear in the unknown parameters with additive noise. The distributed estimation task is for each sub-system to compute the globally optimal estimate of its own parameters using its own measurement and information shared with the network through neighborhood communication. We first provide a fully distributed iterative algorithm to asymptotically compute the global optimal estimate. The convergence rate of the algorithm will be maximized using a scaling parameter and a preconditioning method. This algorithm works for a general network. For a network without loops, we also provide a different iterative algorithm to compute the global optimal estimate which converges in a finite number of steps. We include numerical experiments to illustrate the performances of the proposed methods.

Distributed weighted least-squares estimation with fast convergence for large-scale systems☆

PubMed Central

Marelli, Damián Edgardo; Fu, Minyue

2015-01-01

In this paper we study a distributed weighted least-squares estimation problem for a large-scale system consisting of a network of interconnected sub-systems. Each sub-system is concerned with a subset of the unknown parameters and has a measurement linear in the unknown parameters with additive noise. The distributed estimation task is for each sub-system to compute the globally optimal estimate of its own parameters using its own measurement and information shared with the network through neighborhood communication. We first provide a fully distributed iterative algorithm to asymptotically compute the global optimal estimate. The convergence rate of the algorithm will be maximized using a scaling parameter and a preconditioning method. This algorithm works for a general network. For a network without loops, we also provide a different iterative algorithm to compute the global optimal estimate which converges in a finite number of steps. We include numerical experiments to illustrate the performances of the proposed methods. PMID:25641976

A systematic review of the efficacy of gait rehabilitation strategies for spinal cord injury

PubMed Central

Lam, Tania; Eng, Janice J; Wolfe, Dalton L; Hsieh, Jane T; Whittaker, Maura

2012-01-01

OBJECTIVE To systematically review the evidence for the efficacy of different rehabilitation strategies on functional ambulation following spinal cord injury (SCI). METHODS A keyword literature search of original articles was used to identify published literature evaluating the effectiveness of any treatment or therapy on functional ambulation in people with SCI. The rigor and quality of each study were scored on standardized scales by two independent reviewers. RESULTS The search yielded 160 articles, of which 119 were excluded for not meeting our inclusion criteria. The remaining 41 articles covered various strategies for improving gait: bodyweight supported treadmill training (BWSTT) (n=12), functional electrical stimulation (FES) (n=7), braces/orthoses (n=10), or a combination of these (n=12). There is strong evidence from randomized controlled trials that functional ambulation outcomes following body-weight supported treadmill training (BWSTT) are comparable to an equivalent intensity of overground gait training in sub-acute SCI. In chronic SCI, evidence from pre-test/post-test studies shows that BWSTT may be effective in improving functional ambulation. Pre-test/post-test or post-test only studies provide evidence that FES may augment functional ambulation in sub-acute/chronic SCI while braces may afford particular benefits to people with complete SCI to stand up and ambulate with assistive devices. CONCLUSIONS Rehabilitation strategies that facilitate repeated practice of gait offer the greatest benefits to functional ambulation in sub-acute or chronic SCI. Supportive devices may augment functional ambulation particularly in people with incomplete SCI. PMID:22915835

FUEL-FLEXIBLE GASIFICATION-COMBUSTION TECHNOLOGY FOR PRODUCTION OF H2 AND SEQUESTRATION-READY CO2

DOE Office of Scientific and Technical Information (OSTI.GOV)

George Rizeq; Janice West; Arnaldo Frydman

It is expected that in the 21st century the Nation will continue to rely on fossil fuels for electricity, transportation, and chemicals. It will be necessary to improve both the process efficiency and environmental impact performance of fossil fuel utilization. GE Global Research (GEGR) has developed an innovative fuel-flexible Unmixed Fuel Processor (UFP) technology to produce H{sub 2}, power, and sequestration-ready CO{sub 2} from coal and other solid fuels. The UFP module offers the potential for reduced cost, increased process efficiency relative to conventional gasification and combustion systems, and near-zero pollutant emissions including NO{sub x}. GEGR (prime contractor) was awardedmore » a contract from U.S. DOE NETL to develop the UFP technology. Work on this Phase I program started on October 1, 2000. The project team includes GEGR, Southern Illinois University at Carbondale (SIU-C), California Energy Commission (CEC), and T. R. Miles, Technical Consultants, Inc. In the UFP technology, coal and air are simultaneously converted into separate streams of (1) high-purity hydrogen that can be utilized in fuel cells or turbines, (2) sequestration-ready CO{sub 2}, and (3) high temperature/pressure vitiated air to produce electricity in a gas turbine. The process produces near-zero emissions and, based on Aspen Plus process modeling, has an estimated process efficiency of 6% higher than IGCC with conventional CO{sub 2} separation. The current R&D program will determine the feasibility of the integrated UFP technology through pilot-scale testing, and will investigate operating conditions that maximize separation of CO{sub 2} and pollutants from the vent gas, while simultaneously maximizing coal conversion efficiency and hydrogen production. The program integrates experimental testing, modeling and economic studies to demonstrate the UFP technology. This is the third annual technical progress report for the UFP program supported by U.S. DOE NETL (Contract No. DE-FC26-00FT40974). This report summarizes program accomplishments for the period starting October 1, 2002 and ending September 30, 2003. The report includes an introduction summarizing the UFP technology, main program tasks, and program objectives; it also provides a summary of program activities and accomplishments covering progress in tasks including lab-scale experimental testing, bench-scale experimental testing, process modeling, pilot-scale system design and assembly, and program management.« less

New asteroseismic scaling relations based on the Hayashi track relation applied to red giant branch stars in NGC 6791 and NGC 6819

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, T.; Li, Y.; Hekker, S., E-mail: wutao@ynao.ac.cn, E-mail: ly@ynao.ac.cn, E-mail: hekker@mps.mpg.de

2014-01-20

Stellar mass M, radius R, and gravity g are important basic parameters in stellar physics. Accurate values for these parameters can be obtained from the gravitational interaction between stars in multiple systems or from asteroseismology. Stars in a cluster are thought to be formed coevally from the same interstellar cloud of gas and dust. The cluster members are therefore expected to have some properties in common. These common properties strengthen our ability to constrain stellar models and asteroseismically derived M, R, and g when tested against an ensemble of cluster stars. Here we derive new scaling relations based on amore » relation for stars on the Hayashi track (√(T{sub eff})∼g{sup p}R{sup q}) to determine the masses and metallicities of red giant branch stars in open clusters NGC 6791 and NGC 6819 from the global oscillation parameters Δν (the large frequency separation) and ν{sub max} (frequency of maximum oscillation power). The Δν and ν{sub max} values are derived from Kepler observations. From the analysis of these new relations we derive: (1) direct observational evidence that the masses of red giant branch stars in a cluster are the same within their uncertainties, (2) new methods to derive M and z of the cluster in a self-consistent way from Δν and ν{sub max}, with lower intrinsic uncertainties, and (3) the mass dependence in the Δν - ν{sub max} relation for red giant branch stars.« less

Study of discrete-particle effects in a one-dimensional plasma simulation with the Krook type collision model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lai, Po-Yen; Chen, Liu; Institute for Fusion Theory and Simulation, Zhejiang University, 310027 Hangzhou

2015-09-15

The thermal relaxation time of a one-dimensional plasma has been demonstrated to scale with N{sub D}{sup 2} due to discrete particle effects by collisionless particle-in-cell (PIC) simulations, where N{sub D} is the particle number in a Debye length. The N{sub D}{sup 2} scaling is consistent with the theoretical analysis based on the Balescu-Lenard-Landau kinetic equation. However, it was found that the thermal relaxation time is anomalously shortened to scale with N{sub D} while externally introducing the Krook type collision model in the one-dimensional electrostatic PIC simulation. In order to understand the discrete particle effects enhanced by the Krook type collisionmore » model, the superposition principle of dressed test particles was applied to derive the modified Balescu-Lenard-Landau kinetic equation. The theoretical results are shown to be in good agreement with the simulation results when the collisional effects dominate the plasma system.« less

Acoustic Characteristics of a Model Isolated Tiltrotor in DNW

NASA Technical Reports Server (NTRS)

Booth, Earl R., Jr.; McCluer, Megan; Tadghighi, Hormoz

1999-01-01

An aeroacoustic wind tunnel test was conducted using a scaled isolated tiltrotor model. Acoustic data were acquired using an in-flow microphone wing traversed beneath the model to map the directivity of the near-field acoustic radiation of the rotor for a parametric variation of rotor angle-of-attack, tunnel speed, and rotor thrust. Acoustic metric data were examined to show trends of impulsive noise for the parametric variations. BVISPL maximum noise levels were found to increase with alpha for constant mu and C(sub T), although the maximum BVI levels were found at much higher a than for a typical helicopter. BVISPL levels were found to increase with mu for constant alpha and C(sub T. BVISPL was found to decrease with increasing CT for constant a and m, although BVISPL increased with thrust for a constant wake geometry. Metric data were also scaled for M(sub up) to evaluate how well simple power law scaling could be used to correct metric data for M(sub up) effects.

Development of Novel Carbon Sorbents for CO{sub 2} Capture

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krishnan, Gopala; Hornbostel, Marc; Bao, Jianer

2013-11-30

An innovative, low-cost, and low-energy-consuming carbon dioxide (CO{sub 2}) capture technology was developed, based on CO{sub 2}adsorption on a high-capacity and durable carbon sorbent. This report describes the (1) performance of the concept on a bench-scale system; (2) results of parametric tests to determine the optimum operating conditions; (3) results of the testing with a flue gas from coal-fired boilers; and (4) evaluation of the technical and economic viability of the technology. The process uses a falling bed of carbon sorbent microbeads to separate the flue gas into two streams: a CO{sub 2} -lean flue gas stream from which >more » 90% of the CP{sub 2} is removed and a pure stream of CO{sub 2} that is ready for compression and sequestration. The carbo sorbent microbeads have several unique properties such as high CO{sub 2} capacity, low heat of adsorption and desorption (25 to 28 kJ/mole), mechanically robust, and rapid adsorption and desorption rates. The capture of CO{sub 2} from the flue gas is performed at near ambient temperatures in whic the sorbent microbeads flow down by gravity counter-current with the up-flow of the flue gas. The adsorbed CO{sub 2} is stripped by heating the CO{sub 2}-loaded sorbent to - 100°C, in contact with low-pressure (- 5 psig) steam in a section at the bottom of the adsorber. The regenerated sorben is dehydrated of adsorbed moisture, cooled, and lifted back to the adsorber. The CO{sub 2} from the desorber is essentially pure and can be dehydrated, compressed, and transported to a sequestration site. Bench-scale tests using a simulated flue gas showed that the integrated system can be operated to provide > 90% CO{sub 2} capture from a 15% CO{sub 2} stream in the adsorber and produce > 98% CO{sub 2} at the outlet of the stripper. Long-term tests ( 1,000 cycles) showed that the system can be operated reliably without sorbent agglomeration or attrition. The bench-scale reactor was also operated using a flue gas stream from a coal-fired boil at the University of Toledo campus for about 135 h, comprising 7,000 cycles of adsorption and desorption using the desulfurized flue gas that contained only 4.5% v/v CO{sub 2}. A capture efficiency of 85 to 95% CO{sub 2} was achieved under steady-state conditi ons. The CO{sub 2} adsorption capacity did not change significantly during the field test, as determined from the CO{sub 2} adsorptio isotherms of fresh and used sorbents. The process is also being tested using the flue gas from a PC-fired power plant at the National Carbon Capture Center (NCCC), Wilsonville, AL. The cost of electricity was calculated for CO{sub 2} capture using the carbon sorbent and compared with the no-CO{sub 2} capture and CO{sub 2} capture with an amine-based system. The increase i the levelized cost of electricity (L-COE) is about 37% for CO{sub 2} capture using the carbon sorbent in comparison to 80% for an amine-based system, demonstrating the economic advantage of C capture using the carbon sorbent. The 37% increase in the L-COE corresponds to a cost of capture of $30/ton of CO{sub 2}, including compression costs, capital cost for the capture system, and increased plant operating and capital costs to make up for reduced plant efficiency. Preliminary sensitivity analyses showed capital costs, pressure drops in the adsorber, and steam requirement for the regenerator are the major variables in determining the cost of CO{sub 2} capture. The results indicate that further long-term testing with a flue gas from a pulverized coal­ fired boiler should be performed to obtain additional data relating to the effects of flue gas contaminants, the ability to reduce pressure drop by using alternate structural packing , and the use of low-cost construction materials.« less

A U.S. Army CH-47 Chinook helicopter slowly lowers the X-40 sub-scale technology demonstrator to the ground under the watchful eyes of ground crew at the conclusion of a captive-carry test flight

NASA Image and Video Library

2000-12-08

A U.S. Army CH-47 Chinook helicopter slowly lowers the X-40 sub-scale technology demonstrator to the ground under the watchful eyes of ground crew at the conclusion of a captive-carry test flight at NASA's Dryden Flight Research Center, Edwards, California. Several captive-carry flights were conducted to check out all operating systems and procedures before the X-40 made its first free flight at Edwards, gliding to a fully-autonomous approach and landing on the Edwards runway. The X-40 is an unpowered 82 percent scale version of the X-37, a Boeing-developed spaceplane designed to demonstrate various advanced technologies for development of future lower-cost access to space vehicles. Flight tests of the X-40 are designed to reduce the risks associated with research flights of the larger, more complex X-37.

Design and field demonstration of a low-NOx burner for TEOR (thermally enhanced oil recovery) steamers

DOE Office of Scientific and Technical Information (OSTI.GOV)

England, G.C.; Kwan, Y.; Payne, R.

1984-10-01

The paper discusses a program that addresses the need for advanced NOx control technology for thermally enhanced oil recovery (TEOR) steam generators. A full-scale (60 million Btu/hr) burner system has been developed and tested, the concept for which was based on fundamental studies. Test results are included for full-scale burner performance in an experimental test furnace, and in a field-operating steam generator which was subsequently retrofitted in a Kern County, California, oilfield. (NOTE: NOx control techniques including low-NOx burners, postflame NH/sub 3/ injection, or other postflame treatment methods--e.g., selective catalytic reduction--have been considered in order to comply with regulations. Themore » level of NOx control required to meet both growth and air quality goals has typically been difficult to achieve with available technology while maintaining acceptable CO and particulate emissions as well as practical flame conditions within the steamer.)« less

One-pot hydrothermal synthesis of ZnS quantum dots/graphene hybrids as a dual anode for sodium ion and lithium ion batteries

NASA Astrophysics Data System (ADS)

Zhang, Rupeng; Wang, Yu; Jia, Mengqiu; Xu, Junjie; Pan, Erzhuang

2018-04-01

Committed to research high-performance sodium-ion batteries(SIBs) and lithium-ion batteries(LIBs) anode materials is attractive but challenging. Among the many promising anode materials, sulfides are considered as promising available anode material. In this paper, we successfully synthesized uniformly dispersed ZnS quantum dots (QDs) with sub-10-nm-scale on graphene nanosheets via a facile hydrothermal method. The prepared ZnS/graphene composites was studied as a dual anode for sodium-ion and lithium-ion batteries. Tested against SIBs, the nanocomposites exhibits an impressive specific capacity of 491 mAh/g at 100 mA/g after 100 cycles. Tested against LIBs, the nanocomposites delivers a superior specific capacity of 759 mAh/g at 100 mA/g after 100 cycles. This excellent performance is mainly due to the fact that graphene can improve the conductivity of the composites and effectively prevent the agglomeration and pulverization of ZnS quantum dots during cycling. Meanwhile, ZnS quantum dots with sub-10-nm-scale may also shorten diffuse path and reduce migration barrier, which is in favor of the full utilization of the active material and the improvement of the stability of the structure

Costs of facility-based HIV testing in Malawi, Zambia and Zimbabwe

PubMed Central

Mwenge, Lawrence; Sande, Linda; Mangenah, Collin; Ahmed, Nurilign; Kanema, Sarah; d’Elbée, Marc; Sibanda, Euphemia; Kalua, Thokozani; Ncube, Gertrude; Johnson, Cheryl C.; Hatzold, Karin; Cowan, Frances M.; Corbett, Elizabeth L.; Ayles, Helen; Maheswaran, Hendramoorthy

2017-01-01

Background Providing HIV testing at health facilities remains the most common approach to ensuring access to HIV treatment and prevention services for the millions of undiagnosed HIV-infected individuals in sub-Saharan Africa. We sought to explore the costs of providing these services across three southern African countries with high HIV burden. Methods Primary costing studies were undertaken in 54 health facilities providing HIV testing services (HTS) in Malawi, Zambia and Zimbabwe. Routinely collected monitoring and evaluation data for the health facilities were extracted to estimate the costs per individual tested and costs per HIV-positive individual identified. Costs are presented in 2016 US dollars. Sensitivity analysis explored key drivers of costs. Results Health facilities were testing on average 2290 individuals annually, albeit with wide variations. The mean cost per individual tested was US$5.03.9 in Malawi, US$4.24 in Zambia and US$8.79 in Zimbabwe. The mean cost per HIV-positive individual identified was US$79.58, US$73.63 and US$178.92 in Malawi, Zambia and Zimbabwe respectively. Both cost estimates were sensitive to scale of testing, facility staffing levels and the costs of HIV test kits. Conclusions Health facility based HIV testing remains an essential service to meet HIV universal access goals. The low costs and potential for economies of scale suggests an opportunity for further scale-up. However low uptake in many settings suggests that demand creation or alternative testing models may be needed to achieve economies of scale and reach populations less willing to attend facility based services. PMID:29036171

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu Shengwei; Yu Jiaguo

Bi{sub 2}WO{sub 6} hierarchical multilayered flower-like assemblies are fabricated on a large scale by a simple hydrothermal method in the presence of polymeric poly(sodium 4-styrenesulfonate). Such 3D Bi{sub 2}WO{sub 6} assemblies are constructed from orderly arranged 2D layers, which are further composed of a large number of interconnected nanoplates with a mean side length of ca. 50 nm. The bimodal mesopores associated with such hierarchical assembly exhibit peak mesopore size of ca. 4 nm for the voids within a layer, and peak mesopore size of ca. 40 nm corresponding to the interspaces between stacked layers, respectively. The formation process ismore » discussed on the basis of the results of time-dependent experiments, which support a novel 'coupled cooperative assembly and localized ripening' formation mechanism. More interestingly, we have noticed that the collective effect related to such hierarchical assembly induces a significantly enhanced optical absorbance in the UV-visible region. This work may shed some light on the design of complex architectures and exploitation of their potential applications. - Graphical abstract: Bi{sub 2}WO{sub 6} hierarchical multilayered flower-like assemblies are fabricated on a large scale by a simple hydrothermal method in the presence of polymeric poly(sodium 4-styrenesulfonate)« less

Micro electro-mechanical heater

DOEpatents

Oh, Yunje; Asif, Syed Amanulla Syed; Cyrankowski, Edward; Warren, Oden Lee

2016-04-19

A sub-micron scale property testing apparatus including a test subject holder and heating assembly. The assembly includes a holder base configured to couple with a sub-micron mechanical testing instrument and electro-mechanical transducer assembly. The assembly further includes a test subject stage coupled with the holder base. The test subject stage is thermally isolated from the holder base. The test subject stage includes a stage subject surface configured to receive a test subject, and a stage plate bracing the stage subject surface. The stage plate is under the stage subject surface. The test subject stage further includes a heating element adjacent to the stage subject surface, the heating element is configured to generate heat at the stage subject surface.

Micro electro-mechanical heater

DOEpatents

Oh, Yunje; Asif, Syed Amanulla Syed; Cyrankowski, Edward; Warren, Oden Lee

2017-09-12

A sub-micron scale property testing apparatus including a test subject holder and heating assembly. The assembly includes a holder base configured to couple with a sub-micron mechanical testing instrument and electro-mechanical transducer assembly. The assembly further includes a test subject stage coupled with the holder base. The test subject stage is thermally isolated from the holder base. The test subject stage includes a stage subject surface configured to receive a test subject, and a stage plate bracing the stage subject surface. The stage plate is under the stage subject surface. The test subject stage further includes a heating element adjacent to the stage subject surface, the heating element is configured to generate heat at the stage subject surface.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brian McPherson

The Southwest Partnership on Carbon Sequestration completed its Phase I program in December 2005. The main objective of the Southwest Partnership Phase I project was to evaluate and demonstrate the means for achieving an 18% reduction in carbon intensity by 2012. Many other goals were accomplished on the way to this objective, including (1) analysis of CO{sub 2} storage options in the region, including characterization of storage capacities and transportation options, (2) analysis and summary of CO{sub 2} sources, (3) analysis and summary of CO{sub 2} separation and capture technologies employed in the region, (4) evaluation and ranking of themore » most appropriate sequestration technologies for capture and storage of CO{sub 2} in the Southwest Region, (5) dissemination of existing regulatory/permitting requirements, and (6) assessing and initiating public knowledge and acceptance of possible sequestration approaches. Results of the Southwest Partnership's Phase I evaluation suggested that the most convenient and practical ''first opportunities'' for sequestration would lie along existing CO{sub 2} pipelines in the region. Action plans for six Phase II validation tests in the region were developed, with a portfolio that includes four geologic pilot tests distributed among Utah, New Mexico, and Texas. The Partnership will also conduct a regional terrestrial sequestration pilot program focusing on improved terrestrial MMV methods and reporting approaches specific for the Southwest region. The sixth and final validation test consists of a local-scale terrestrial pilot involving restoration of riparian lands for sequestration purposes. The validation test will use desalinated waters produced from one of the geologic pilot tests. The Southwest Regional Partnership comprises a large, diverse group of expert organizations and individuals specializing in carbon sequestration science and engineering, as well as public policy and outreach. These partners include 21 state government agencies and universities, five major electric utility companies, seven oil, gas and coal companies, three federal agencies, the Navajo Nation, several NGOs, and the Western Governors Association. This group is continuing its work in the Phase II Validation Program, slated to conclude in 2009.« less

Further evaluation of traditional icing scaling methods

NASA Technical Reports Server (NTRS)

Anderson, David N.

1996-01-01

This report provides additional evaluations of two methods to scale icing test conditions; it also describes a hybrid technique for use when scaled conditions are outside the operating envelope of the test facility. The first evaluation is of the Olsen method which can be used to scale the liquid-water content in icing tests, and the second is the AEDC (Ruff) method which is used when the test model is less than full size. Equations for both scaling methods are presented in the paper, and the methods were evaluated by performing icing tests in the NASA Lewis Icing Research Tunnel (IRT). The Olsen method was tested using 53 cm diameter NACA 0012 airfoils. Tests covered liquid-water-contents which varied by as much as a factor of 1.8. The Olsen method was generally effective in giving scale ice shapes which matched the reference shapes for these tests. The AEDC method was tested with NACA 0012 airfoils with chords from 18 cm to 53 cm. The 53 cm chord airfoils were used in reference tests, and 1/2 and 1/3 scale tests were made at conditions determined by applying the AEDC scaling method. The scale and reference airspeeds were matched in these tests. The AEDC method was found to provide fairly effective scaling for 1/2 size tests, but for 1/3 size models, scaling was generally less effective. In addition to these two scaling methods, a hybrid approach was also tested in which the Olsen method was used to adjust the LWC after size was scaled using the constant Weber number method. This approach was found to be an effective way to test when scaled conditions would otherwise be outside the capability of the test facility.

US Highway 84 chip seal field trials and laboratory test results.

DOT National Transportation Integrated Search

2009-03-23

This report contains laboratory and field testing of US Highway 84 in Lincoln county Mississippi. A full scale field test consisting of seven polymer modified asphalt emulsions and a CRS-2 control emulsion was constructed in September of 1989 and sub...

Directional fractal signature methods for trabecular bone texture in hand radiographs: Data from the Osteoarthritis Initiative

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wolski, M., E-mail: marcin.wolski@curtin.edu.au; Podsiadlo, P.; Stachowiak, G. W.

Purpose: To develop directional fractal signature methods for the analysis of trabecular bone (TB) texture in hand radiographs. Problems associated with the small size of hand bones and the orientation of fingers were addressed. Methods: An augmented variance orientation transform (AVOT) and a quadrant rotating grid (QRG) methods were developed. The methods calculate fractal signatures (FSs) in different directions. Unlike other methods they have the search region adjusted according to the size of bone region of interest (ROI) to be analyzed and they produce FSs defined with respect to any chosen reference direction, i.e., they work for arbitrary orientation ofmore » fingers. Five parameters at scales ranging from 2 to 14 pixels (depending on image size and method) were derived from rose plots of Hurst coefficients, i.e., FS in dominating roughness (FS{sub Sta}), vertical (FS{sub V}) and horizontal (FS{sub H}) directions, aspect ratio (StrS), and direction signatures (StdS), respectively. The accuracy in measuring surface roughness and isotropy/anisotropy was evaluated using 3600 isotropic and 800 anisotropic fractal surface images of sizes between 20 × 20 and 64 × 64 pixels. The isotropic surfaces had FDs ranging from 2.1 to 2.9 in steps of 0.1, and the anisotropic surfaces had two dominating directions of 30° and 120°. The methods were used to find differences in hand TB textures between 20 matched pairs of subjects with (cases: approximate Kellgren-Lawrence (KL) grade ≥2) and without (controls: approximate KL grade <2) radiographic hand osteoarthritis (OA). The OA Initiative public database was used and 20 × 20 pixel bone ROIs were selected on 5th distal and middle phalanges. The performance of the AVOT and QRG methods was compared against a variance orientation transform (VOT) method developed earlier [M. Wolski, P. Podsiadlo, and G. W. Stachowiak, “Directional fractal signature analysis of trabecular bone: evaluation of different methods to detect early osteoarthritis in knee radiographs,” Proc. Inst. Mech. Eng., Part H 223, 211–236 (2009)]. Results: The AVOT method correctly quantified the isotropic and anisotropic surfaces for all image sizes and scales. Values of FS{sub Sta} were significantly different (P < 0.05) between the isotropic surfaces. Using the VOT and QRG methods no differences were found at large scales for the isotropic surfaces that are smaller than 64 × 64 and 48 × 48 pixels, respectively, and at some scales for the anisotropic surfaces with size 48 × 48 pixels. Compared to controls, using the AVOT and QRG methods the authors found that OA TB textures were less rough (P < 0.05) in the dominating and horizontal directions (i.e., lower FS{sub Sta} and FS{sub H}), rougher in the vertical direction (i.e., higher FS{sub V}) and less anisotropic (i.e., higher StrS) than controls. No differences were found using the VOT method. Conclusions: The AVOT method is well suited for the analysis of bone texture in hand radiographs and it could be potentially useful for early detection and prediction of hand OA.« less

Goethite Bench-scale and Large-scale Preparation Tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Josephson, Gary B.; Westsik, Joseph H.

2011-10-23

The Hanford Waste Treatment and Immobilization Plant (WTP) is the keystone for cleanup of high-level radioactive waste from our nation's nuclear defense program. The WTP will process high-level waste from the Hanford tanks and produce immobilized high-level waste glass for disposal at a national repository, low activity waste (LAW) glass, and liquid effluent from the vitrification off-gas scrubbers. The liquid effluent will be stabilized into a secondary waste form (e.g. grout-like material) and disposed on the Hanford site in the Integrated Disposal Facility (IDF) along with the low-activity waste glass. The major long-term environmental impact at Hanford results from technetiummore » that volatilizes from the WTP melters and finally resides in the secondary waste. Laboratory studies have indicated that pertechnetate ({sup 99}TcO{sub 4}{sup -}) can be reduced and captured into a solid solution of {alpha}-FeOOH, goethite (Um 2010). Goethite is a stable mineral and can significantly retard the release of technetium to the environment from the IDF. The laboratory studies were conducted using reaction times of many days, which is typical of environmental subsurface reactions that were the genesis of this new process. This study was the first step in considering adaptation of the slow laboratory steps to a larger-scale and faster process that could be conducted either within the WTP or within the effluent treatment facility (ETF). Two levels of scale-up tests were conducted (25x and 400x). The largest scale-up produced slurries of Fe-rich precipitates that contained rhenium as a nonradioactive surrogate for {sup 99}Tc. The slurries were used in melter tests at Vitreous State Laboratory (VSL) to determine whether captured rhenium was less volatile in the vitrification process than rhenium in an unmodified feed. A critical step in the technetium immobilization process is to chemically reduce Tc(VII) in the pertechnetate (TcO{sub 4}{sup -}) to Tc(Iv)by reaction with the ferrous ion, Fe{sup 2+}-Fe{sup 2+} is oxidized to Fe{sup 3+} - in the presence of goethite seed particles. Rhenium does not mimic that process; it is not a strong enough reducing agent to duplicate the TcO{sub 4}{sup -}/Fe{sup 2+} redox reactions. Laboratory tests conducted in parallel with these scaled tests identified modifications to the liquid chemistry necessary to reduce ReO{sub 4}{sup -} and capture rhenium in the solids at levels similar to those achieved by Um (2010) for inclusion of Tc into goethite. By implementing these changes, Re was incorporated into Fe-rich solids for testing at VSL. The changes also changed the phase of iron that was in the slurry product: rather than forming goethite ({alpha}-FeOOH), the process produced magnetite (Fe{sub 3}O{sub 4}). Magnetite was considered by Pacific Northwest National Laboratory (PNNL) and VSL to probably be a better product to improve Re retention in the melter because it decomposes at a higher temperature than goethite (1538 C vs. 136 C). The feasibility tests at VSL were conducted using Re-rich magnetite. The tests did not indicate an improved retention of Re in the glass during vitrification, but they did indicate an improved melting rate (+60%), which could have significant impact on HLW processing. It is still to be shown whether the Re is a solid solution in the magnetite as {sup 99}Tc was determined to be in goethite.« less

A demonstration test and evaluation of the Cannon Low-NO{sub x} Digester System. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1995-08-01

Since 1985, Cannon Boiler Works, Inc. has been carrying out research and development efforts to perfect a system for removing nitrogen oxides, NO{sub x}, from the exhaust gases of furnaces, gas turbines, chemical reactors, incinerators and boilers.Computer simulations, bench-scale tests and pilot plant testing have proved that the system is capable of removing substantially all of the NO{sub x} from natural gas-fired equipment exhaust streams. Furthermore when retrofit to industrial boilers, both capital costs and operating costs are lower than for competing processes, while performance is much better. The Cannon system for removing NO{sub x}, originally designated as the Cannonmore » NO{sub x} Digester, has recently been renamed the Low Temperature Oxidation (LTO) System for NO{sub x} and SO{sub x} Reduction. It will be engineered and marketed by Cannon Technology, Inc, a wholly owned subsidiary of Cannon Boiler Works, Inc. Cannon has US patents for the process and for the associated equipment and has patent applications pending in Europe. Cannon`s Low Temperature Oxidation, LTO, process has proved effective for reducing the levels of NO{sub x}, CO, CO{sub 2}, SO{sub 2} and particulates from boiler flue gases.« less

What are the constraints and opportunities for HIVST scale-up in Africa? Evidence from Kenya, Malawi and South Africa.

PubMed

van Rooyen, Heidi; Tulloch, Olivia; Mukoma, Wanjiru; Makusha, Tawanda; Chepuka, Lignet; Knight, Lucia C; Peck, Roger B; Lim, Jeanette M; Muturi, Nelly; Chirwa, Ellen; Taegtmeyer, Miriam

2015-01-01

HIV self-testing (HIVST) has the potential to increase uptake of HIV testing among untested populations in sub-Saharan Africa and is on the brink of scale-up. However, it is unclear to what extent HIVST would be supported by stakeholders, what policy frameworks are in place and how variations between contexts might influence country-preparedness for scale-up. This qualitative study assessed the perceptions of HIVST among stakeholders in three sub-Saharan countries. Fifty-four key informant interviews were conducted in Kenya (n=16), Malawi (n=26) and South Africa (n=12) with government policy makers, academics, activists, donors, procurement specialists, laboratory practitioners and health providers. A thematic analysis was conducted in each country and a common coding framework allowed for inter-country analysis to identify common and divergent themes across contexts. Respondents welcomed the idea of an accurate, easy-to-use, rapid HIV self-test which could increase testing across all populations. High-risk groups, such as men, Men who have sex with men (MSM), couples and young people in particular, could be targeted through a range of health facility and community-based distribution points. HIVST is already endorsed in Kenya, and political support for scale-up exists in South Africa and Malawi. However, several caveats remain. Further research, policy and ensuing guidelines should consider how to regulate, market and distribute HIVST, ensure quality assurance of tests and human rights, and critically, link testing to appropriate support and treatment services. Low literacy levels in some target groups would also need context-specific consideration before scale up. World Health Organization (WHO) policy and regulatory frameworks are needed to guide the process in those areas which are new or specific to self-testing. Stakeholders in three HIV endemic sub-Saharan countries felt that HIVST will be an important complement to existing community and facility-based testing approaches if accompanied by the same essential components of any HIV testing service, including access to accurate information and linkages to care. While there is an increasingly positive global policy environment regarding HIVST, several implementation and social challenges limit scale-up. There is a need for further research to provide contextual and operational evidence that addresses concerns and contributes to normative WHO guidance.

Control system health test system and method

DOEpatents

Hoff, Brian D.; Johnson, Kris W.; Akasam, Sivaprasad; Baker, Thomas M.

2006-08-15

A method is provided for testing multiple elements of a work machine, including a control system, a component, a sub-component that is influenced by operations of the component, and a sensor that monitors a characteristic of the sub-component. In one embodiment, the method is performed by the control system and includes sending a command to the component to adjust a first parameter associated with an operation of the component. Also, the method includes detecting a sensor signal from the sensor reflecting a second parameter associated with a characteristic of the sub-component and determining whether the second parameter is acceptable based on the command. The control system may diagnose at least one of the elements of the work machine when the second parameter of the sub-component is not acceptable.

Hints on the nature of dark matter from the properties of Milky Way satellites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderhalden, Donnino; Diemand, Juerg; Schneider, Aurel

2013-03-01

The nature of dark matter is still unknown and one of the most fundamental scientific mysteries. Although successfully describing large scales, the standard cold dark matter model (CDM) exhibits possible shortcomings on galactic and sub-galactic scales. It is exactly at these highly non-linear scales where strong astrophysical constraints can be set on the nature of the dark matter particle. While observations of the Lyman-α forest probe the matter power spectrum in the mildly non-linear regime, satellite galaxies of the Milky Way provide an excellent laboratory as a test of the underlying cosmology on much smaller scales. Here we present resultsmore » from a set of high resolution simulations of a Milky Way sized dark matter halo in eight distinct cosmologies: CDM, warm dark matter (WDM) with a particle mass of 2 keV and six different cold plus warm dark matter (C+WDM) models, varying the fraction, f{sub wdm}, and the mass, m{sub wdm}, of the warm component. We used three different observational tests based on Milky Way satellite observations: the total satellite abundance, their radial distribution and their mass profile. We show that the requirement of simultaneously satisfying all three constraints sets very strong limits on the nature of dark matter. This shows the power of a multi-dimensional small scale approach in ruling out models which would be still allowed by large scale observations.« less

United States Department of Energy solar receiver technology development

NASA Astrophysics Data System (ADS)

Klimas, P. C.; Diver, R. B.; Chavez, J. M.

The United States Department of Energy (DOE), through Sandia National Laboratories, has been conducting a Solar Thermal Receiver Technology Development Program, which maintains a balance between analytical modeling, bench and small scale testing, and experimentation conducted at scales representative of commercially-sized equipment. Central receiver activities emphasize molten salt-based systems on large scales and volumetric devices in the modeling and small scale testing. These receivers are expected to be utilized in solar power plants rated between 100 and 200 MW. Distributed receiver research focuses on liquid metal refluxing devices. These are intended to mate parabolic dish concentrators with Stirling cycle engines in the 5 to 25 kW(sub e) power range. The effort in the area of volumetric receivers is less intensive and highly cooperative in nature. A ceramic foam absorber of Sandia design was successfully tested on the 200 kW(sub t) test bed at Plataforma Solar during 1989. Material integrity during the approximately 90-test series was excellent. Significant progress has been made with parabolic dish concentrator-mounted receivers using liquid metals (sodium or a potassium/sodium mixture) as heat transport media. Sandia has successfully solar-tested a pool boiling reflux receiver sized to power a 25 kW Stirling engine. Boiling stability and transient operation were both excellent. This document describes these activities in detail and will outline plans for future development.

Modelling uncertainties and possible future trends of precipitation and temperature for 10 sub-basins in Columbia River Basin (CRB)

NASA Astrophysics Data System (ADS)

Ahmadalipour, A.; Rana, A.; Qin, Y.; Moradkhani, H.

2014-12-01

Trends and changes in future climatic parameters, such as, precipitation and temperature have been a central part of climate change studies. In the present work, we have analyzed the seasonal and yearly trends and uncertainties of prediction in all the 10 sub-basins of Columbia River Basin (CRB) for future time period of 2010-2099. The work is carried out using 2 different sets of statistically downscaled Global Climate Model (GCMs) projection datasets i.e. Bias correction and statistical downscaling (BCSD) generated at Portland State University and The Multivariate Adaptive Constructed Analogs (MACA) generated at University of Idaho. The analysis is done for with 10 GCM downscaled products each from CMIP5 daily dataset totaling to 40 different downscaled products for robust analysis. Summer, winter and yearly trend analysis is performed for all the 10 sub-basins using linear regression (significance tested by student t test) and Mann Kendall test (0.05 percent significance level), for precipitation (P), temperature maximum (Tmax) and temperature minimum (Tmin). Thereafter, all the parameters are modelled for uncertainty, across all models, in all the 10 sub-basins and across the CRB for future scenario periods. Results have indicated in varied degree of trends for all the sub-basins, mostly pointing towards a significant increase in all three climatic parameters, for all the seasons and yearly considerations. Uncertainty analysis have reveled very high change in all the parameters across models and sub-basins under consideration. Basin wide uncertainty analysis is performed to corroborate results from smaller, sub-basin scale. Similar trends and uncertainties are reported on the larger scale as well. Interestingly, both trends and uncertainties are higher during winter period than during summer, contributing to large part of the yearly change.

Validation of the Korean Version of the Scales for Outcomes in Parkinson's Disease-Sleep.

PubMed

Sung, Young Hee; Kim, Hee Jin; Koh, Seong Beom; Kim, Joong Seok; Kim, Sang Jin; Cheon, Sang Myung; Cho, Jin Whan; Kim, Yoon Joong; Ma, Hyeo Il; Park, Mee Young; Baik, Jong Sam; Lee, Phil Hyu; Chung, Sun Ju; Kim, Jong Min; Song, In Uk; Kim, Han Joon; Kim, Ji Young; Kwon, Do Young; Lee, Jae Hyeok; Lee, Jee Young; Kim, Ji Seon; Yun, Ji Young; Hong, Jin Yong; Kim, Mi Jung; Youn, Jinyoung; Kim, Ji Sun; Oh, Eung Seok; Yang, Hui Jun; Yoon, Won Tae; You, Sooyeoun; Kwon, Kyum Yil; Park, Hyung Eun; Lee, Su Yun; Kim, Younsoo; Kim, Hee Tae; Ahn, Tae Beom

2018-01-08

Sleep problems commonly occur in patients with Parkinson's disease (PD), and are associated with a lower quality of life. The aim of the current study was to translate the English version of the Scales for Outcomes in Parkinson's Disease-Sleep (SCOPA-S) into the Korean version of SCOPA-S (K-SCOPA-S), and to evaluate its reliability and validity for use by Korean-speaking patients with PD. In total, 136 patients with PD from 27 movement disorder centres of university-affiliated hospitals in Korea were enrolled in this study. They were assessed using SCOPA, Hoehn and Yahr Scale (HYS), Unified Parkinson's Disease Rating Scale (UPDRS), Parkinson's Disease Sleep Scale 2nd version (PDSS-2), Non-motor Symptoms Scale (NMSS), Montgomery Asberg Depression Scale (MADS), 39-item Parkinson's Disease Questionnaire (PDQ39), Neurogenic Orthostatic Hypotension Questionnaire (NOHQ), and Rapid Eye Movement Sleep Behaviour Disorder Questionnaire (RBDQ). The test-retest reliability was assessed over a time interval of 10-14 days. The internal consistency (Cronbach's α-coefficients) of K-SCOPA-S was 0.88 for nighttime sleep (NS) and 0.75 for daytime sleepiness (DS). Test-retest reliability was 0.88 and 0.85 for the NS and DS, respectively. There was a moderate correlation between the NS sub-score and PDSS-2 total score. The NS and DS sub-scores of K-SCOPA-S were correlated with motor scale such as HYS, and non-motor scales such as UPDRS I, UPDRS II, MADS, NMSS, PDQ39, and NOHQ while the DS sub-score was with RBDQ. The K-SCOPA-S exhibited good reliability and validity for the assessment of sleep problems in the Korean patients with PD. © 2018 The Korean Academy of Medical Sciences.

The X-40 sub-scale technology demonstrator is suspended under a U.S. Army CH-47 Chinook cargo helicopter during a captive-carry test flight at NASA's Dryden Flight Research Center, Edwards, California.

NASA Image and Video Library

2000-12-08

The X-40 sub-scale technology demonstrator is suspended under a U.S. Army CH-47 Chinook cargo helicopter during a captive-carry test flight at NASA's Dryden Flight Research Center, Edwards, California. The captive carry flights are designed to verify the X-40's navigation and control systems, rigging angles for its sling, and stability and control of the helicopter while carrying the X-40 on a tether. Following a series of captive-carry flights, the X-40 made free flights from a launch altitude of about 15,000 feet above ground, gliding to a fully autonomous landing. The X-40 is an unpowered 82 percent scale version of the X-37, a Boeing-developed spaceplane designed to demonstrate various advanced technologies for development of future lower-cost access to space vehicles.

Coupling lattice Boltzmann and continuum equations for flow and reactive transport in porous media.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coon, Ethan; Porter, Mark L.; Kang, Qinjun

2012-06-18

In spatially and temporally localized instances, capturing sub-reservoir scale information is necessary. Capturing sub-reservoir scale information everywhere is neither necessary, nor computationally possible. The lattice Boltzmann Method for solving pore-scale systems. At the pore-scale, LBM provides an extremely scalable, efficient way of solving Navier-Stokes equations on complex geometries. Coupling pore-scale and continuum scale systems via domain decomposition. By leveraging the interpolations implied by pore-scale and continuum scale discretizations, overlapping Schwartz domain decomposition is used to ensure continuity of pressure and flux. This approach is demonstrated on a fractured medium, in which Navier-Stokes equations are solved within the fracture while Darcy'smore » equation is solved away from the fracture Coupling reactive transport to pore-scale flow simulators allows hybrid approaches to be extended to solve multi-scale reactive transport.« less

Galaxy formation in Lambda greater than 0 Friedmann models: Consequences for the number counts versus redshift test

NASA Technical Reports Server (NTRS)

Martel, Hugo

1994-01-01

We study the effect of the cosmological constant Lambda on galaxy formation using a simple spherical top-hat overdensity model. We consider models with Omega(sub 0) = 0.2, lambda(sub 0) = 0, and Omega(sub 0) = 0.2, lambda(sub 0) = 0.8 (where Omega(sub 0) is the density parameter, and lambda(sub 0) identically equal Lambda/3 H(sub 0 exp 2) where H(sub 0) is the Hubble constant). We adjust the initial power spectrum amplitude so that both models reproduce the same large-scale structures. The galaxy formation era in the lambda(sub 0) = 0 model occurs early (z approximately 6) and is very short, whereas in the lambda(sub 0) = 0.8 model the galaxy formation era starts later (z approximately 4), and last much longer, possibly all the way to the present. Consequently, galaxies at low redshift (z less than 1) are significantly more evolved in the lambda(sub 0) = 0 model than in the lambda(sub 0) = 0.8 model. This result implies that previous attempts to determine Lambda using the number counts versus redshift test are probably unreliable.

Fuselage Versus Subcomponent Panel Response Correlation Based on ABAQUS Explicit Progressive Damage Analysis Tools

NASA Technical Reports Server (NTRS)

Gould, Kevin E.; Satyanarayana, Arunkumar; Bogert, Philip B.

2016-01-01

Analysis performed in this study substantiates the need for high fidelity vehicle level progressive damage analyses (PDA) structural models for use in the verification and validation of proposed sub-scale structural models and to support required full-scale vehicle level testing. PDA results are presented that capture and correlate the responses of sub-scale 3-stringer and 7-stringer panel models and an idealized 8-ft diameter fuselage model, which provides a vehicle level environment for the 7-stringer sub-scale panel model. Two unique skin-stringer attachment assumptions are considered and correlated in the models analyzed: the TIE constraint interface versus the cohesive element (COH3D8) interface. Evaluating different interfaces allows for assessing a range of predicted damage modes, including delamination and crack propagation responses. Damage models considered in this study are the ABAQUS built-in Hashin procedure and the COmplete STress Reduction (COSTR) damage procedure implemented through a VUMAT user subroutine using the ABAQUS/Explicit code.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Verkerk, B.

In 1959 a fuel development program was undertaken based on UO/sub 2/ in which it was intended to study all variables that could influence the quality of fabricated UO/sub 2/-pellets. Later this program was extended to a study of electrolytic UO/sub 2/ with the fabrication of swaged or vibratory compacted fuel elements in mind, and recently the study of the UO/sub 2/-PuO/sub 2/ system was incorporated in it. In order to obtain a better knowledge of the UO/sub 2/- powders that can be used for sintering purposes, an extensive study was made of various preparation methods. A small plutonium laboratorymore » containing equipment for the preparation of UO/sub 2/-- PuO/sub 2/ pellets containing 1 to 10% PuO/sub 2/ was set up and preliminary experiments were performed. Work on a small scale was done on pressing and sintering of UO/sub 2/ made along various routes. The reduction process was also studied. For the regeneration of scrap, especially for the case of enriched material, a 5-kg batch dissolution and precipitation plant was built. This installation is also used for various precipitation studies on a larger scale. Within the scope of tue fuel development program the study of canning materials is also of great importance. For the ship-propulsion reactor Zircaloy-2 was chosen as canning material. Various welding experiments were done in an argon-arc welding chamber and it was found that under well selected conditions very satisfactory end-cap welds could be obtained. 1n the corrosion program it became clear that proper conditioning is of utmost importance. Means of pre-operation treatment are being studied. In the HFR a low-temperature, low-pressure loop for the irradiation of capsules is in regular operation. The pressurized loop now under construction was designed for testing of fuel rods and clusters as planned for the ship-propulsion reactor, under conditions close to those of the actual reactor. The facilities for the post- irradiation measurements consist of two lead cells. (auth)« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Attig, R.C.; Crawford, L.W.; Lynch, T.P.

Proof-of-Concept (POC) scale demonstration of such technology is currently being carried out at the US Department of Energy's (DOE's) Coal-Fired Flow Facility (CFFF), located at The University of Tennessee Space Institute (UTSI) in Tullahoma, Tennessee and at the Component Development and Integration Facility in Butte, Montana. The CFFF is dedicated to the evaluation of downstream (steam cycle) components and technology that may be considered for a full-scale MHD system. The objectives of the CFFF testing include the demonstration of various pollution control devices and techniques at a scale sufficient for future scale-up. The CFFF offers a unique test environment inmore » which emissions control techniques can be developed and evaluated through emissions and environmental monitoring. Results thus far have demonstrated the ability of sulfur oxide (SO{sub x}), nitrogen oxide (NO{sub x}) and particulate emissions well below the New Source Performance Standards (NSPS). Regeneration of the potassium sulfate to produce sulfur-free compounds also has been demonstrated. The experimental program at the CFFF is now aimed at determining the optimum conditions for future commercial scale designs. Because of increased interests in Air Toxics, measurements of nitrous oxide (N{sub 2}O), a potential greenhouse gas, priority pollutants (inorganic as well as organics), and chlorine-containing species (Cl{sub 2} and HCl) are also included in our ongoing efforts. Environmental monitoring activities are being pursued to develop an environmental impact assessment data base. These include the use of three ambient air sites to determine the impacts of gaseous and particulate emissions, five lake water sites to determine impacts due to process water discharges and seven sites to collect terrestrial data on possible soil contamination and tree growth. In this paper, we will summarize the status of our ongoing environmental program. 16 refs., 15 figs., 3 tabs.« less

USING BROAD-SCALE METRICS TO DEVELOP INDICATORS OF WATERSHED VULNERABILITY IN THE OZARK MOUNTAINS (USA)

EPA Science Inventory

Multiple broad-scale landscape metrics were tested as potential indicators of total phosphorus (TP) concentration, total ammonia (TA) concentration, and Escherichia coli (E. coli) bacteria count, among 244 sub-watersheds in the Ozark Mountains (USA). Indicator models were develop...

An examination of the psychometric properties of the Rosenberg Self-Esteem Scale (RSES) in Chinese acute coronary syndrome (ACS) patients.

PubMed

Martin, Colin R; Thompson, David R; Chan, Dominic S

2006-11-01

The psychometric properties of the Rosenberg Self-Esteem Scale (RSES) as a clinical research instrument for acute coronary syndrome (ACS) patients were investigated in a translated Chinese version of the instrument. A confirmatory factor analysis was conducted on the RSES to establish its psychometric properties in 128 ACS patients over two observation points (within 1 week and 6 months post-admission for ACS). Internal and test-retest reliability of the RSES-TOT (all-items) and RSES-POS sub-scale (positively valenced items) were found to be acceptable. The RSES-NEG sub-scale (negatively valenced items) lacked acceptable internal reliability. The underlying factor structure of the RSES comprised two distinct but related factors, though there was inconsistency in best model fit indices at the 1-week observation point. The use of the RSES as two sub-scales (RSES-POS and RSES-NEG) may be clinically useful in evaluating the influence of this important psychological construct on the health outcomes of patients with ACS. Directions for future research are indicated.

Carbon Molecular Sieve Membrane as a True One Box Unit for Large Scale Hydrogen Production

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Paul

2012-05-01

IGCC coal-fired power plants show promise for environmentally-benign power generation. In these plants coal is gasified to syngas then processed in a water gas-shift (WGS) reactor to maximize the hydrogen/CO{sub 2} content. The gas stream can then be separated into a hydrogen rich stream for power generation and/or further purified for sale as a chemical and a CO{sub 2} rich stream for the purpose of carbon capture and storage (CCS). Today, the separation is accomplished using conventional absorption/desorption processes with post CO{sub 2} compression. However, significant process complexity and energy penalties accrue with this approach, accounting for ~20% of themore » capital cost and ~27% parasitic energy consumption. Ideally, a one-box process is preferred in which the syngas is fed directly to the WGS reactor without gas pre-treatment, converting the CO to hydrogen in the presence of H{sub 2}S and other impurities and delivering a clean hydrogen product for power generation or other uses. The development of such a process is the primary goal of this project. Our proposed "one-box" process includes a catalytic membrane reactor (MR) that makes use of a hydrogen-selective, carbon molecular sieve (CMS) membrane, and a sulfur-tolerant Co/Mo/Al{sub 2}O{sub 3} catalyst. The membrane reactor's behavior has been investigated with a bench top unit for different experimental conditions and compared with the modeling results. The model is used to further investigate the design features of the proposed process. CO conversion >99% and hydrogen recovery >90% are feasible under the operating pressures available from IGCC. More importantly, the CMS membrane has demonstrated excellent selectivity for hydrogen over H{sub 2}S (>100), and shown no flux loss in the presence of a synthetic "tar"-like material, i.e., naphthalene. In summary, the proposed "one-box" process has been successfully demonstrated with the bench-top reactor. In parallel we have successfully designed and fabricated a full-scale CMS membrane and module for the proposed application. This full-scale membrane element is a 3" diameter with 30"L, composed of ~85 single CMS membrane tubes. The membrane tubes and bundles have demonstrated satisfactory thermal, hydrothermal, thermal cycling and chemical stabilities under an environment simulating the temperature, pressure and contaminant levels encountered in our proposed process. More importantly, the membrane module packed with the CMS bundle was tested for over 30 pressure cycles between ambient pressure and >300 -600 psi at 200 to 300°C without mechanical degradation. Finally, internal baffles have been designed and installed to improve flow distribution within the module, which delivered 90% separation efficiency in comparison with the efficiency achieved with single membrane tubes. In summary, the full-scale CMS membrane element and module have been successfully developed and tested satisfactorily for our proposed one-box application; a test quantity of elements/modules have been fabricated for field testing. Multiple field tests have been performed under this project at National Carbon Capture Center (NCCC). The separation efficiency and performance stability of our full-scale membrane elements have been verified in testing conducted for times ranging from 100 to >250 hours of continuous exposure to coal/biomass gasifier off-gas for hydrogen enrichment with no gas pre-treatment for contaminants removal. In particular, "tar-like" contaminants were effectively rejected by the membrane with no evidence of fouling. In addition, testing was conducted using a hybrid membrane system, i.e., the CMS membrane in conjunction with the palladium membrane, to demonstrate that 99+% H{sub 2} purity and a high degree of CO{sub 2} capture could be achieved. In summary, the stability and performance of the full-scale hydrogen selective CMS membrane/module has been verified in multiple field tests in the presence of coal/biomass gasifier off-gas under this project. A promising process scheme has been developed for power generation and/or hydrogen coproduction with CCS based upon our proposed "one-box" process. Our preliminary economic analysis indicates about 10% reduction in the required electricity selling price and ~40% cost reduction in CCS on per ton CO{sub 2} can be achieved in comparison with the base case involving conventional WGS with a two-stage Selexsol® for CCS. Long term field tests (e.g., >1,000 hrs) with the incorporation of the catalyst for the WGS membrane reactor and more in-depth analysis of the process scheme are recommended for the future study.« less

Continued Water-Based Phase Change Material Heat Exchanger Development

NASA Technical Reports Server (NTRS)

Hansen, Scott W.; Sheth, Rubik B.; Poynot, Joe; Giglio, Tony; Ungar, Gene K.

2015-01-01

In a cyclical heat load environment such as low Lunar orbit, a spacecraft's radiators are not sized to meet the full heat rejection demands. Traditionally, a supplemental heat rejection device (SHReD) such as an evaporator or sublimator is used to act as a "topper" to meet the additional heat rejection demands. Utilizing a Phase Change Material (PCM) heat exchanger (HX) as a SHReD provides an attractive alternative to evaporators and sublimators as PCM HX's do not use a consumable, thereby leading to reduced launch mass and volume requirements. In continued pursuit of water PCM HX development two full-scale, Orion sized water-based PCM HX's were constructed by Mezzo Technologies. These HX's were designed by applying prior research on freeze front propagation to a full-scale design. Design options considered included bladder restraint and clamping mechanisms, bladder manufacturing, tube patterns, fill/drain methods, manifold dimensions, weight optimization, and midplate designs. Two units, Units A and B, were constructed and differed only in their midplate design. Both units failed multiple times during testing. This report highlights learning outcomes from these tests and are applied to a final sub-scale PCM HX which is slated to be tested on the ISS in early 2017.

Development and Validation of a Fatigue Assessment Scale for U.S. Construction Workers

PubMed Central

Zhang, Mingzong; Sparer, Emily H.; Murphy, Lauren A.; Dennerlein, Jack T.; Fang, Dongping; Katz, Jeffrey N.; Caban-Martinez, Alberto J.

2015-01-01

Objective To develop a fatigue assessment scale and test its reliability and validity for commercial construction workers. Methods Using a two-phased approach, we first identified items for the development of a Fatigue Assessment Scale for Construction Workers (FASCW) through review of existing scales in the scientific literature, key informant interviews (n=11) and focus groups (3 groups with 6 workers each) with construction workers. The second phase included assessment for the reliability, validity and sensitivity of the new scale using a repeated-measures study design with a convenience sample of construction workers (n=144). Results Phase one resulted in a 16-item preliminary scale that after factor analysis yielded a final 10-item scale with two sub-scales (“Lethargy” and “Bodily Ailment”).. During phase two, the FASCW and its subscales demonstrated satisfactory internal consistency (alpha coefficients were FASCW (0.91), Lethargy (0.86) and Bodily Ailment (0.84)) and acceptable test-retest reliability (Pearson Correlations Coefficients: 0.59–0.68; Intraclass Correlation Coefficients: 0.74–0.80). Correlation analysis substantiated concurrent and convergent validity. A discriminant analysis demonstrated that the FASCW differentiated between groups with arthritis status and different work hours. Conclusions The 10-item FASCW with good reliability and validity is an effective tool for assessing the severity of fatigue among construction workers. PMID:25603944

Establishing a coherent and replicable measurement model of the Edinburgh Postnatal Depression Scale.

PubMed

Martin, Colin R; Redshaw, Maggie

2018-06-01

The 10-item Edinburgh Postnatal Depression Scale (EPDS) is an established screening tool for postnatal depression. Inconsistent findings in factor structure and replication difficulties have limited the scope of development of the measure as a multi-dimensional tool. The current investigation sought to robustly determine the underlying factor structure of the EPDS and the replicability and stability of the most plausible model identified. A between-subjects design was used. EPDS data were collected postpartum from two independent cohorts using identical data capture methods. Datasets were examined with confirmatory factor analysis, model invariance testing and systematic evaluation of relational and internal aspects of the measure. Participants were two samples of postpartum women in England assessed at three months (n = 245) and six months (n = 217). The findings showed a three-factor seven-item model of the EPDS offered an excellent fit to the data, and was observed to be replicable in both datasets and invariant as a function of time point of assessment. Some EPDS sub-scale scores were significantly higher at six months. The EPDS is multi-dimensional and a robust measurement model comprises three factors that are replicable. The potential utility of the sub-scale components identified requires further research to identify a role in contemporary screening practice. Copyright © 2018 The Authors. Published by Elsevier B.V. All rights reserved.

Generalized Chirp Scaling Combined with Baseband Azimuth Scaling Algorithm for Large Bandwidth Sliding Spotlight SAR Imaging

PubMed Central

Yi, Tianzhu; He, Zhihua; He, Feng; Dong, Zhen; Wu, Manqing

2017-01-01

This paper presents an efficient and precise imaging algorithm for the large bandwidth sliding spotlight synthetic aperture radar (SAR). The existing sub-aperture processing method based on the baseband azimuth scaling (BAS) algorithm cannot cope with the high order phase coupling along the range and azimuth dimensions. This coupling problem causes defocusing along the range and azimuth dimensions. This paper proposes a generalized chirp scaling (GCS)-BAS processing algorithm, which is based on the GCS algorithm. It successfully mitigates the deep focus along the range dimension of a sub-aperture of the large bandwidth sliding spotlight SAR, as well as high order phase coupling along the range and azimuth dimensions. Additionally, the azimuth focusing can be achieved by this azimuth scaling method. Simulation results demonstrate the ability of the GCS-BAS algorithm to process the large bandwidth sliding spotlight SAR data. It is proven that great improvements of the focus depth and imaging accuracy are obtained via the GCS-BAS algorithm. PMID:28555057

DEVELOPMENT AND DEPLOYMENT OF VACUUM SALT DISTILLATION AT THE SAVANNAH RIVER SITE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pierce, R.; Pak, D.; Edwards, T.

2010-10-28

The Savannah River Site has a mission to dissolve fissile materials and disposition them. The primary fissile material is plutonium dioxide (PuO{sub 2}). To support dissolution of these materials, the Savannah River National Laboratory (SRNL) designed and demonstrated a vacuum salt distillation (VSD) apparatus using both representative radioactive samples and non-radioactive simulant materials. Vacuum salt distillation, through the removal of chloride salts, increases the quantity of materials suitable for processing in the site's HB-Line Facility. Small-scale non-radioactive experiments at 900-950 C show that >99.8 wt % of the initial charge of chloride salt distilled from the sample boat with recoverymore » of >99.8 wt % of the ceric oxide (CeO{sub 2}) - the surrogate for PuO{sub 2} - as a non-chloride bearing 'product'. Small-scale radioactive testing in a glovebox demonstrated the removal of sodium chloride (NaCl) and potassium chloride (KCl) from 13 PuO{sub 2} samples. Chloride concentrations were distilled from a starting concentration of 1.8-10.8 wt % to a final concentration <500 mg/kg chloride. Initial testing of a non-radioactive, full-scale production prototype is complete. A designed experiment evaluated the impact of distillation temperature, time at temperature, vacuum, product depth, and presence of a boat cover. Significant effort has been devoted to mechanical considerations to facilitate simplified operation in a glovebox.« less

Design and development of surface rainfall forecast products on GRAPES_MESO model

NASA Astrophysics Data System (ADS)

Zhili, Liu

2016-04-01

In this paper, we designed and developed the surface rainfall forecast products using medium scale GRAPES_MESO model precipitation forecast products. The horizontal resolution of GRAPES_MESO model is 10km*10km, the number of Grids points is 751*501, vertical levels is 26, the range is 70°E－145.15°E, 15°N－64.35 °N. We divided the basin into 7 major watersheds. Each watersheds was divided into a number of sub regions. There were 95 sub regions in all. Tyson polygon method is adopted in the calculation of surface rainfall. We used 24 hours forecast precipitation data of GRAPES_MESO model to calculate the surface rainfall. According to the site of information and boundary information of the 95 sub regions, the forecast surface rainfall of each sub regions was calculated. We can provide real-time surface rainfall forecast products every day. We used the method of fuzzy evaluation to carry out a preliminary test and verify about the surface rainfall forecast product. Results shows that the fuzzy score of heavy rain, rainstorm and downpour level forecast rainfall were higher, the fuzzy score of light rain level was lower. The forecast effect of heavy rain, rainstorm and downpour level surface rainfall were better. The rate of missing and empty forecast of light rainfall level surface rainfall were higher, so it's fuzzy score were lower.

Multi-scale modelling of elastic moduli of trabecular bone

PubMed Central

Hamed, Elham; Jasiuk, Iwona; Yoo, Andrew; Lee, YikHan; Liszka, Tadeusz

2012-01-01

We model trabecular bone as a nanocomposite material with hierarchical structure and predict its elastic properties at different structural scales. The analysis involves a bottom-up multi-scale approach, starting with nanoscale (mineralized collagen fibril) and moving up the scales to sub-microscale (single lamella), microscale (single trabecula) and mesoscale (trabecular bone) levels. Continuum micromechanics methods, composite materials laminate theory and finite-element methods are used in the analysis. Good agreement is found between theoretical and experimental results. PMID:22279160

Effect of temperature on the fracture toughness in the nuclear reactor pressure vessel steel (SA508-3)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oh, S.W.; Lim, M.B.; Yoon, H.K.

1994-12-31

The elastic-plastic fracture toughness J{sub IC} of the Nuclear Reactor Pressure Vessel Steel (SA508-3) which has high toughness was obtained at three temperatures (room temperature, {minus}20 C, 200 C) using a 1/2 CT specimen. Especially the two methods recommended in ASTM and JSME were compared. It was found that difficulty exists in obtaining J{sub IC} by ASTM R-curve method, while JSME R-curve method yielded good results. The stretched zone width method gave slightly larger J{sub IC} values than those by the R-curve method for SA508-3 steel and the blunting line was not affected by the test temperatures. The relation betweenmore » SZW and J, SZW and J/E and SZW and J/{sigma}{sub ys} before initiation of a stable crack growth in the fracture toughness test at three temperatures is described.« less

A microscale three-dimensional urban energy balance model for studying surface temperatures

NASA Astrophysics Data System (ADS)

Krayenhoff, E. Scott; Voogt, James A.

2007-06-01

A microscale three-dimensional (3-D) urban energy balance model, Temperatures of Urban Facets in 3-D (TUF-3D), is developed to predict urban surface temperatures for a variety of surface geometries and properties, weather conditions, and solar angles. The surface is composed of plane-parallel facets: roofs, walls, and streets, which are further sub-divided into identical square patches, resulting in a 3-D raster-type model geometry. The model code is structured into radiation, conduction and convection sub-models. The radiation sub-model uses the radiosity approach and accounts for multiple reflections and shading of direct solar radiation. Conduction is solved by finite differencing of the heat conduction equation, and convection is modelled by empirically relating patch heat transfer coefficients to the momentum forcing and the building morphology. The radiation and conduction sub-models are tested individually against measurements, and the complete model is tested against full-scale urban surface temperature and energy balance observations. Modelled surface temperatures perform well at both the facet-average and the sub-facet scales given the precision of the observations and the uncertainties in the model inputs. The model has several potential applications, such as the calculation of radiative loads, and the investigation of effective thermal anisotropy (when combined with a sensor-view model).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Menon, R.; Grames, L.M.

Pilot Carrousel testing was conducted for about three months on wastewaters generated at a major potato processing facility in 1993. The testing focused toward removal of BOD, NH{sub 3} and NO{sub 3}, and Total-P. After five-six weeks that it took for the system to reach steady state operation, the pilot plant was able to treat the wastewaters quite well. Effluent BOD{sub 5} and TKN values were less than 8 and 4 mg/L, respectively, during the second half of testing. Total-P in the effluent was less than 10 mg/L, although this step was not optimized. Based on the pilot testing, amore » full-scale Carrousel activated sludge plant was designed and commissioned in 1994. This plant is currently treating all the wastewaters from the facility and performing contaminant removals at a very high level.« less

The relationship between media consumption and health-related anxieties after the Fukushima Daiichi nuclear disaster.

PubMed

Sugimoto, Amina; Nomura, Shuhei; Tsubokura, Masaharu; Matsumura, Tomoko; Muto, Kaori; Sato, Mikiko; Gilmour, Stuart

2013-01-01

The Fukushima Daiichi nuclear disaster caused a global panic by a release of harmful radionuclides. In a disaster setting, misusage of contemporary media sources available today can lead to disseminated incorrect information and panic. The study aims to build a scale which examines associations between media and individual anxieties, and to propose effective media usages for future disaster management. The University of Tokyo collaborated with the Fukushima local government to conduct a radiation-health-seminar for a total of 1560 residents, at 12 different locations in Fukushima. A 13 item questionnaire collected once before and after a radiation-seminar was used on factor analysis to develop sub-scales for multiple regression models, to determine relationships between the sub-scales and media type consumed. A paired t-test was used to examine any changes in sub-scale of pre- and post-seminar scores. Three sub-scales were revealed and were associated with different media types: was with rumors, while concern for the future was positively associated with regional-newspapers and negatively with national-newspapers. Anxiety about social-disruption was associated with radio. The seminar had a significant effect on anxiety reduction for all the three sub-scales. Different media types were associated with various heightened concerns, and that a radiation seminar was helpful to reduce anxieties in the post-disaster setting. By tailoring post-disaster messages via specific media types, i.e., radio, it may be possible to effectively convey important information, as well as to calm fears about particular elements of post-disaster recovery and to combat rumors.

A fast learning method for large scale and multi-class samples of SVM

NASA Astrophysics Data System (ADS)

Fan, Yu; Guo, Huiming

2017-06-01

A multi-class classification SVM(Support Vector Machine) fast learning method based on binary tree is presented to solve its low learning efficiency when SVM processing large scale multi-class samples. This paper adopts bottom-up method to set up binary tree hierarchy structure, according to achieved hierarchy structure, sub-classifier learns from corresponding samples of each node. During the learning, several class clusters are generated after the first clustering of the training samples. Firstly, central points are extracted from those class clusters which just have one type of samples. For those which have two types of samples, cluster numbers of their positive and negative samples are set respectively according to their mixture degree, secondary clustering undertaken afterwards, after which, central points are extracted from achieved sub-class clusters. By learning from the reduced samples formed by the integration of extracted central points above, sub-classifiers are obtained. Simulation experiment shows that, this fast learning method, which is based on multi-level clustering, can guarantee higher classification accuracy, greatly reduce sample numbers and effectively improve learning efficiency.

The Turkish adaptation of scale to measure patient perceptions of the quality of nursing care and related hospital services: A validity and reliability study

PubMed Central

Oren, Besey; Zengin, Neriman; Yildiz, Nebahat

2016-01-01

OBJECTIVE: This study aimed to test the validity and reliability of a version of the tool developed in Sri Lanka in 2011 to assess patient perceptions of the quality of nursing care and related hospital services created for use with Turkish patients. METHODS: This methodological study was conducted between November 2013 and November 2014 after obtaining ethical approval and organizational permission. Data was collected during discharge from 180 adult patients who were hospitalized for at least 3 days at a medical school hospital located in Istanbul. After language validation, validity and reliability analyses of the scale were conducted. Content validity, content validity index (CVI), construct validity, and exploratory factor analysis were assessed and examined, and reliability was tested using the Cronbach’s alpha coefficient and item-total correlations. RESULTS: Mean CVI was found to be 0.95, which is above expected value. Exploratory factor analysis revealed 4 factors with eigenvalues above 1, which explained 82.4% of total variance in the Turkish version of the tool to measure patient perceptions of nursing care and other hospital services. Factor loading for each item was ≥.40. Cronbach’s alpha coefficient of sub-dimensions and total scale were found to be 0.84-0.98 and 0.98, respectively. Item-total correlations ranged from 0.56 to 0.83 for the entire group, which was above expected values. CONCLUSION: The Turkish version of the scale to assess patient perceptions of the quality of nursing care and related hospital services, which comprised 4 sub-dimensions and 36 items, was found to be valid and reliable for use with the Turkish population. PMID:28275750

Mach 5 to 7 RBCC Propulsion System Testing at NASA-LeRC HTF

NASA Technical Reports Server (NTRS)

Perkins, H. Douglas; Thomas, Scott R.; Pack, William D.

1996-01-01

A series of Mach 5 to 7 freejet tests of a Rocket Based Combined Cycle (RBCC) engine were cnducted at the NASA Lewis Research Center (LERC) Hypersonic Tunnel Facility (HTF). This paper describes the configuration and operation of the HTF and the RBCC engine during these tests. A number of facility support systems are described which were added or modified to enhance the HTF test capability for conducting this experiment. The unfueled aerodynamic perfor- mance of the RBCC engine flowpath is also presented and compared to sub-scale test results previously obtained in the NASA LERC I x I Supersonic Wind Tunnel (SWT) and to Computational Fluid Dynamic (CFD) analysis results. This test program demonstrated a successful configuration of the HTF for facility starting and operation with a generic RBCC type engine and an increased range of facility operating conditions. The ability of sub-scale testing and CFD analysis to predict flowpath performance was also shown. The HTF is a freejet, blowdown propulsion test facility that can simulate up to Mach 7 flight conditions with true air composition. Mach 5, 6, and 7 facility nozzles are available, each with an exit diameter of 42 in. This combination of clean air, large scale, and Mach 7 capabilities is unique to the HTF. This RBCC engine study is the first engine test program conducted at the HTF since 1974.

Real-time mapping of the corneal sub-basal nerve plexus by in vivo laser scanning confocal microscopy

NASA Astrophysics Data System (ADS)

Guthoff, Rudolf F.; Zhivov, Andrey; Stachs, Oliver

2010-02-01

The aim of the study was to produce two-dimensional reconstruction maps of the living corneal sub-basal nerve plexus by in vivo laser scanning confocal microscopy in real time. CLSM source data (frame rate 30Hz, 384x384 pixel) were used to create large-scale maps of the scanned area by selecting the Automatic Real Time (ART) composite mode. The mapping algorithm is based on an affine transformation. Microscopy of the sub-basal nerve plexus was performed on normal and LASIK eyes as well as on rabbit eyes. Real-time mapping of the sub-basal nerve plexus was performed in large-scale up to a size of 3.2mm x 3.2mm. The developed method enables a real-time in vivo mapping of the sub-basal nerve plexus which is stringently necessary for statistically firmed conclusions about morphometric plexus alterations.

Improved understanding of geologic CO{sub 2} storage processes requires risk-driven field experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oldenburg, C.M.

2011-06-01

The need for risk-driven field experiments for CO{sub 2} geologic storage processes to complement ongoing pilot-scale demonstrations is discussed. These risk-driven field experiments would be aimed at understanding the circumstances under which things can go wrong with a CO{sub 2} capture and storage (CCS) project and cause it to fail, as distinguished from accomplishing this end using demonstration and industrial scale sites. Such risk-driven tests would complement risk-assessment efforts that have already been carried out by providing opportunities to validate risk models. In addition to experimenting with high-risk scenarios, these controlled field experiments could help validate monitoring approaches to improvemore » performance assessment and guide development of mitigation strategies.« less

Finite element simulation of structural performance on flexible pavements with stabilized base/treated sub-base materials under accelerated loading : research project capsule.

DOT National Transportation Integrated Search

2008-12-01

PROBLEM: The full-scale accelerated pavement testing (APT) provides a unique tool for pavement : engineers to directly collect pavement performance and failure data under heavy : wheel loading. However, running a full-scale APT experiment is very exp...

Fast Grid Frequency Support from Distributed Inverter-Based Resources

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoke, Anderson F

This presentation summarizes power hardware-in-the-loop testing performed to evaluate the ability of distributed inverter-coupled generation to support grid frequency on the fastest time scales. The research found that distributed PV inverters and other DERs can effectively support the grid on sub-second time scales.

Cognitive deficits in amyotrophic lateral sclerosis evaluated by event-related potentials.

PubMed

Ogawa, Tomohiro; Tanaka, Hideaki; Hirata, Koichi

2009-04-01

To determine the cognitive profiles in non-demented, relatively less handicapped patients with early-stage sporadic amyotrophic lateral sclerosis (ALS) by using neuropsychological tests, event-related potentials (ERPs) and clinical scale. We recruited 19 patients with sporadic ALS (eight with limb-onset, 11 with bulbar-onset) and 19 controls. In addition to the mini-mental state examination and the Wechsler adult intelligence scale-revised, we assessed the frontal lobe function with Wisconsin card sorting test, Stroop test and trail making test. We used auditory 'oddball' counting paradigm for the ERPs under 20-channel electroencephalogram (EEG) recording. Global field power (GFP) was computed, and its peak amplitudes and latencies of N1/N2/P3 were determined. The results of ERP and neuropsychological tests were correlated with respiratory function and clinical scale. No global cognitive impairment except for subtle frontal dysfunction was detected, although N1/N2/P3 GFP latencies were significantly prolonged in ALS patients than in the controls. Vital capacity correlated with P3 GFP amplitude, and the relative bulbar functional rating scale correlated with P3 GFP latency. Our findings indicated the presence of sub-clinical cognitive deficits in non-demented, sporadic ALS patients. In addition, clinical sub-types and respiratory function dependently influenced cognitive function in patients with sporadic ALS. ERP confirmed cognitive impairment in patients with sporadic ALS.

Microwave hydrothermal synthesis and photocatalytic activity of AgIn{sub 5}S{sub 8} for the degradation of dye

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang Wenjuan; Li Danzhen, E-mail: dzli@fzu.edu.c; Sun Meng

2010-10-15

AgIn{sub 5}S{sub 8} powders were successfully synthesized by a microwave hydrothermal method for the first time. This method is a mild and highly efficient route involves no templates, catalysts, or surfactants. Therefore, it is very promising for the low-cost and large-scale industrial production. The samples were characterized by X-ray diffraction, UV-vis spectroscopy, X-ray photoelectron spectroscopy, and scanning electron microscopy. The photocatalytic activity of AgIn{sub 5}S{sub 8} nanoparticles was investigated through the degradation of methyl orange under visible light irradiation. Compared with TiO{sub 2-x}N{sub x}, AgIn{sub 5}S{sub 8} has exhibited a superior activity under the same condition. A liquid chromatogram-mass spectrometermore » was used to separate and identify the dye and degradation products generated during the reaction. According to the experiment results, a possible mechanism for the degradation of organic pollutant over AgIn{sub 5}S{sub 8} was proposed. - Graphical abstract: Compared with TiO{sub 2-x}N{sub x}, AgIn{sub 5}S{sub 8} has exhibited a superior activity under the same condition.« less

Professional self-concept and professional values of senior students of the nursing department.

PubMed

Çöplü, Mehtap; Tekinsoy Kartın, Pınar

2018-01-01

This study was carried out in order to determine professional self-concept and professional values in the students, who were studying in the final year of the nursing department in schools providing undergraduate education in the Inner Anatolia Region. This cross-sectional study was conducted on a total of 619 senior students of nursing departments in the Inner Anatolia Region. Data were collected using a Student Information Form, Professional Self-Concept Scale for the Student Nurses, and The Nurses' Professional Values Scale. Descriptive statistics, the Shapiro-Wilk test, the t-test, analysis of variance, and the Bonferroni tests were used for data analysis. Ethical Considerations: A written consent was obtained from Ethics Board of Erciyes University Faculty of Medicine and from nursing schools participating in the study. Prior to data collection, students were informed about the purpose of the study and gave written and verbal consents. Participation in the study was on voluntary basis. In the study, students' total and sub-dimension scores from the Professional Self-Concept Scale for the Student Nurses and total scores from the Nurses' Professional Values Scale were moderately high. It was detected that women received higher scores than men from the sub-dimension of professional attributes; the students who had positive perception of the nursing image and voluntarily selected their department received high scores from professional satisfaction, professional competence, and professional attributes sub-dimensions of the Professional Self-Concept Scale for the Student Nurses ( p < 0.001). In order to improve students' perceptions of professional self-concept and professional values, it is thought that students' awareness should be increased on these topics.

Final Report - Assessment of Testing Options for the NTR at the INL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Howe, Steven D; McLing, Travis L; McCurry, Michael

One of the main technologies that can be developed to dramatically enhance the human exploration of space is the nuclear thermal rocket (NTR). Several studies over the past thirty years have shown that the NTR can reduce the cost of a lunar outpost, reduce the risk of a human mission to Mars, enable fast transits for most missions throughout the solar system, and reduce the cost and time for robotic probes to deep space. Three separate committees of the National Research Council of the National Academy of Sciences have recommended that NASA develop the NTR. One of the primary issuesmore » in development of the NTR is the ability to verify a flight ready unit. Three main methods can be used to validate safe operation of a NTR: 1) Full power, full duration test in an above ground facility that scrubs the rocket exhaust clean of any fission products; 2) Full power , full duration test using the Subsurface Active Filtering of Exhaust (SAFE) technique to capture the exhaust in subsurface strata; 3) Test of the reactor fuel at temperature and power density in a driver reactor with subsequent first test of the fully integrated NTR in space. The first method, the above ground facility, has been studied in the past. The second method, SAFE, has been examined for application at the Nevada Test Site. The third method relies on the fact that the Nuclear Furnace series of tests in 1971 showed that the radioactive exhaust coming from graphite based fuel for the NTR could be completely scrubbed of fission products and the clean hydrogen flared into the atmosphere. Under funding from the MSFC, the Center for Space Nuclear Research (CSNR) at the Idaho National laboratory (INL) has completed a reexamination of Methods 2 and 3 for implementation at the INL site. In short, the effort performed the following: 1) Assess the geology of the INL site and determine a location suitable SAFE testing; 2) Perform calculations of gas transport throughout the geology; 3) Produce a cost estimate of a non-nuclear , sub-scale test using gas injection to validate the computational models; 4) Produce a preliminary cost estimate to build a nuclear furnace equivalent facility to test NTR fuel on a green field location on the INL site. The results show that the INL geology is substantially better suited to the SAFE testing method than the NTS site. The existence of impermeable interbeds just above the sub-surface aquifer ensure that no material from the test, radioactive or not, can enter the water table. Similar beds located just below the surface will prevent any gaseous products from reaching the surface for dispersion. The extremely high permeability of the strata between the interbeds allows rapid dispersion of the rocket exhaust. In addition, the high permeability suggests that a lower back-pressure may develop in the hole against the rocket thrust, which increases safety of operations. Finally, the cost of performing a sub-scale, non-nuclear verification experiment was determined to be $3M. The third method was assessed through discussions with INL staff resident at the site. In essence, any new Category I facility on any DOE site will cost in excess of $250M. Based on the results of this study, a cost estimate for testing a nuclear rocket at the INL site appears to be warranted. Given the fact that a new nuclear fuel may be possible that does not release any fission products, the SAFE testing option appears to be the most affordable.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ionita, G.; Stefanescu, I.

The nature and performance of our patented catalysts, with platinum on carbon and polytetrafluorethylene [Pt/C/PTFE] and platinum on styrenedivynilbenzene and polystyrene [Pt/STB/PS], used in a water-hydrogen isotope exchange process are presented. The behaviour of the two catalysts in tritiated water was tested by determining their physical and structural characteristics as well as the catalytic activity before and after immersion in tritiated water. The test results emphasized that the two catalysts are highly active in the hydrogen - water vapor (H{sub 2(g)}-H{sub 2}O{sub (v)}) isotopic exchange and highly stable to tritium radiation. It was discovered that Pt/SDB/PS catalyst proved to bemore » quite unstable in the hydrogen- water vapor - water (H{sub 2(g)}-H{sub 2}O{sub (v)}-H{sub 2}O{sub (1)}) isotopic exchange, while the Pt/C/PTFE catalyst was highly stable. Thus, the Pt/C/PTFE catalyst was chosen for hydrogen isotope separation by liquid hydrogen cryogenic distillation combined with water - hydrogen isotopic exchange in a demonstration scale plant. 5 refs., 8 figs., 2 tabs.« less

Estimating GATE rainfall with geosynchronous satellite images

NASA Technical Reports Server (NTRS)

Stout, J. E.; Martin, D. W.; Sikdar, D. N.

1979-01-01

A method of estimating GATE rainfall from either visible or infrared images of geosynchronous satellites is described. Rain is estimated from cumulonimbus cloud area by the equation R = a sub 0 A + a sub 1 dA/dt, where R is volumetric rainfall, A cloud area, t time, and a sub 0 and a sub 1 are constants. Rainfall, calculated from 5.3 cm ship radar, and cloud area are measured from clouds in the tropical North Atlantic. The constants a sub 0 and a sub 1 are fit to these measurements by the least-squares method. Hourly estimates by the infrared version of this technique correlate well (correlation coefficient of 0.84) with rain totals derived from composited radar for an area of 100,000 sq km. The accuracy of this method is described and compared to that of another technique using geosynchronous satellite images. It is concluded that this technique provides useful estimates of tropical oceanic rainfall on a convective scale.

Women's views on consent, counseling and confidentiality in PMTCT: a mixed-methods study in four African countries

PubMed Central

2012-01-01

Background Ambitious UN goals to reduce the mother-to-child transmission of HIV have not been met in much of Sub-Saharan Africa. This paper focuses on the quality of information provision and counseling and disclosure patterns in Burkina Faso, Kenya, Malawi and Uganda to identify how services can be improved to enable better PMTCT outcomes. Methods Our mixed-methods study draws on data obtained through: (1) the MATCH (Multi-country African Testing and Counseling for HIV) study's main survey, conducted in 2008-09 among clients (N = 408) and providers at health facilities offering HIV Testing and Counseling (HTC) services; 2) semi-structured interviews with a sub-set of 63 HIV-positive women on their experiences of stigma, disclosure, post-test counseling and access to follow-up psycho-social support; (3) in-depth interviews with key informants and PMTCT healthcare workers; and (4) document study of national PMTCT policies and guidelines. We quantitatively examined differences in the quality of counseling by country and by HIV status using Fisher's exact tests. Results The majority of pregnant women attending antenatal care (80-90%) report that they were explained the meaning of the tests, explained how HIV can be transmitted, given advice on prevention, encouraged to refer their partners for testing, and given time to ask questions. Our qualitative findings reveal that some women found testing regimes to be coercive, while disclosure remains highly problematic. 79% of HIV-positive pregnant women reported that they generally keep their status secret; only 37% had disclosed to their husband. Conclusion To achieve better PMTCT outcomes, the strategy of testing women in antenatal care (perceived as an exclusively female domain) when they are already pregnant needs to be rethought. When scaling up HIV testing programs, it is particularly important that issues of partner disclosure are taken seriously. PMID:22236097

Noninvasive Determination of Bone Mechanical Properties Using Vibration Response: A Refined Model and Validation in vivo

NASA Technical Reports Server (NTRS)

Roberts, S. G.; Hutchinson, T. M.; Arnaud, S. B.; Kiratli, B. J; Steele, C. R.

1996-01-01

Accurate non-invasive mechanical measurement of long bones is made difficult by the masking effect of surrounding soft tissues. Mechanical response tissue analysis (MRTA) offers a method for separating the effects of the soft tissue and bone; however, a direct validation has been lacking. A theoretical analysis of wave propagation through the compressed tissue revealed a strong mass effect dependent on the relative accelerations of the probe and bone. The previous mathematical model of the bone and overlying tissue system was reconfigured to incorporate the theoretical finding. This newer model (six-parameter) was used to interpret results using MRTA to determine bone cross-sectional bending stiffness, EI(sub MRTA). The relationship between EI(sub MRTA) and theoretical EI values for padded aluminum rods was R(sup 2) = 0.999. A biological validation followed using monkey tibias. Each bone was tested in vivo with the MRTA instrument. Postmortem, the same tibias were excised and tested to failure in three-point bending to determine EI(sub 3-PT) and maximum load. Diaphyseal bone mineral density (BMD) measurements were also made. The relationship between EI(sub 3-PT) and in vivo EI(sub MRTA) using the six-parameter model is strong (R(sup 2) = 0.947) and better than that using the older model (R(sup 2) = 0.645). EI(sub MRTA) and BMD are also highly correlated (R(sup 2) = 0.853). MRTA measurements in vivo and BMD ex vivo are both good predictors of scaled maximum strength (R(sup 2) = 0.915 and R(sup 2) = 0.894, respectively). This is the first biological validation of a non- invasive mechanical measurement of bone by comparison to actual values. The MRTA technique has potential clinical value for assessing long-bone mechanical properties.

Prevalence and Predisposing Factors for Depressive Status in Chinese Patients with Obstructive Sleep Apnoea: A Large-Sample Survey

PubMed Central

Dai, Yaozhang; Li, Xuewu; Zhang, Xin; Wang, Sihua; Sang, Jianzhong; Tian, Xiufen; Cao, Hua

2016-01-01

Background and Objective Recently, there are few studies reporting on depressive status and obstructive sleep apnoea (OSA) in China. A large-sample survey was to be performed to explore the prevalence of depressive status and related factors in Chinese patients with OSA. Methods From among a randomly-selected group of OSA patients, 1,327 met inclusion criteria. After screening with the Symptom Checklist 90 (SCL-90) and Self-Rating Depression Scale (SDS), patients were assigned to OSA without depressive status (control group, n = 698) and OSA with depressive status (n = 629) groups. Using chi-squared testing, the correlation analyses between the depressive status and OSA patient demographic and clinical variables were tested. Then depression-related risk factors in OSA patients were analysed using stepwise linear regression analysis. The effects of family and social factors on depressive status in OSA patients were investigated using Mann-Whitney U (one of nonparametric test). Results The prevalence of depressive status was 47.4% in OSA patients. Depressive status was significantly associated with female gender, single status, Family Burden Scale of Disease (FBS), Family APGAR Index (APGAR), apnoea-hypopnea index (AHI), and Perceived Social Support Scale (PSSS). Stepwise linear regression analysis further indicated that single status, hypoxemia, APGAR, AHI, PSSS, AHI, and FBS were all risk factors for depressive status in OSA patients. The total of the FBS score and three of its sub-factors scores (family daily activities, family relationships and mental health of family members) were higher, and the total of the APGAR score and two of its sub-factors scores (adaptability and affection) were lower in OSA with depressive status compared with the control group. Besides, the total score for the PSSS and scores for its two sub-factors (family support and social support) were all lower in OSA patients with depressive status than those of the control group. Conclusions Depressive status has high comorbid rate in Chinese OSA patients and is significantly associated with single status, apnoea-hypopnea index, hypoxemia, family and social supports. PMID:26934192

LARGE SCALE METHOD FOR THE PRODUCTION AND PURIFICATION OF CURIUM

DOEpatents

Higgins, G.H.; Crane, W.W.T.

1959-05-19

A large-scale process for production and purification of Cm/sup 242/ is described. Aluminum slugs containing Am are irradiated and declad in a NaOH-- NaHO/sub 3/ solution at 85 to 100 deg C. The resulting slurry filtered and washed with NaOH, NH/sub 4/OH, and H/sub 2/O. Recovery of Cm from filtrate and washings is effected by an Fe(OH)/sub 3/ precipitation. The precipitates are then combined and dissolved ln HCl and refractory oxides centrifuged out. These oxides are then fused with Na/sub 2/CO/sub 3/ and dissolved in HCl. The solution is evaporated and LiCl solution added. The Cm, rare earths, and anionic impurities are adsorbed on a strong-base anfon exchange resin. Impurities are eluted with LiCl--HCl solution, rare earths and Cm are eluted by HCl. Other ion exchange steps further purify the Cm. The Cm is then precipitated as fluoride and used in this form or further purified and processed. (T.R.H.)

Anaerobic sludge digestion with a biocatalytic additive. [Lactobacillus acidophilus

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghosh, S.; Henry, M.P.; Fedde, P.A.

1982-01-01

Aimed at improving the process operating characteristics of anaerobic digestion for sludge stabilization and SNG production, this study evaluates the effects of a lactobacillus additive under normal, variable, and overload conditions. This whey fermentation product of an acid-tolerant strain of L. acidophilus fortified with CoCO/sub 3/, (NH/sub 4/)/sub 2/HPO/sub 4/, ferrous lactate, and lactic acid provides growth factors, metabolic intermediates, and enzymes needed for substrate degradation and cellular synthesis. Data indicate that the biochemical additive increases methane yield, gas production rate, and volatile solids reduction; decreases volatile acids accumulation; enhances the digester buffer capacity; and improves the fertilizer value andmore » dewatering characteristics of the digested residue. Digester capacities could be potentially doubled when the feed is so treated. Results of field tests with six full-scale digesters confirm observations made with bench-scale digesters.« less

Directional Multi-scale Modeling of High-Resolution Computed Tomography (HRCT) Lung Images for Diffuse Lung Disease Classification

NASA Astrophysics Data System (ADS)

Vo, Kiet T.; Sowmya, Arcot

A directional multi-scale modeling scheme based on wavelet and contourlet transforms is employed to describe HRCT lung image textures for classifying four diffuse lung disease patterns: normal, emphysema, ground glass opacity (GGO) and honey-combing. Generalized Gaussian density parameters are used to represent the detail sub-band features obtained by wavelet and contourlet transforms. In addition, support vector machines (SVMs) with excellent performance in a variety of pattern classification problems are used as classifier. The method is tested on a collection of 89 slices from 38 patients, each slice of size 512x512, 16 bits/pixel in DICOM format. The dataset contains 70,000 ROIs of those slices marked by experienced radiologists. We employ this technique at different wavelet and contourlet transform scales for diffuse lung disease classification. The technique presented here has best overall sensitivity 93.40% and specificity 98.40%.

Precision determination of weak charge of {sup 133}Cs from atomic parity violation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Porsev, S. G.; School of Physics, University of New South Wales, Sydney, New South Wales 2052; Petersburg Nuclear Physics Institute, Gatchina, Leningrad District 188300

2010-08-01

We discuss results of the most accurate to-date test of the low-energy electroweak sector of the standard model of elementary particles. Combining previous measurements with our high-precision calculations we extracted the weak charge of the {sup 133}Cs nucleus, Q{sub W}=-73.16(29){sub exp}(20){sub th}[S. G. Porsev, K. Beloy, and A. Derevianko, Phys. Rev. Lett. 102, 181601 (2009)]. The result is in perfect agreement with Q{sub W}{sup SM} predicted by the standard model, Q{sub W}{sup SM}=-73.16(3), and confirms energy dependence (or running) of the electroweak interaction and places constraints on a variety of new physics scenarios beyond the standard model. In particular, wemore » increase the lower limit on the masses of extra Z-bosons predicted by models of grand unification and string theories. This paper provides additional details to the earlier paper. We discuss large-scale calculations in the framework of the coupled-cluster method, including full treatment of single, double, and valence triple excitations. To determine the accuracy of the calculations we computed energies, electric-dipole amplitudes, and hyperfine-structure constants. An extensive comparison with high-accuracy experimental data was carried out.« less

Adsorptive removal of catalyst poisons from coal gas for methanol synthesis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bhatt, B.L.; Golden, T.C.; Hsiung, T.H.

1991-12-01

As an integral part of the liquid-phase methanol (LPMEOH) process development program, the present study evaluated adsorptive schemes to remove traces of catalyst poisons such as iron carbonyl, carbonyl sulfide, and hydrogen sulfide from coal gas on a pilot scale. Tests were conducted with coal gas from the Cool Water gasification plant at Daggett, California. Iron carbonyl, carbonyl sulfide, and hydrogen sulfide were effectively removed from the coal gas. The adsorption capacities of Linde H-Y zeolite and Calgon BPL carbon for Fe(CO){sub 5} compared well with previous bench-scale results at similar CO{sub 2} partial pressure. Adsorption of COS by Calgonmore » FCA carbon appeared to be chemical and nonregenerable by thermal treatment in nitrogen. A Cu/Zn catalyst removed H{sub 2}S very effectively. With the adsorption system on-line, a methanol catalyst showed stable activity during 120 h operation, demonstrating the feasibility of adsorptive removal of trace catalyst poisons from the synthesis gas. Mass transfer coefficients were estimated for Fe(CO){sub 5} and COS removal which can be directly used for design and scale up.« less

Sub-scale Waterflow Cavitation and Dynamic Transfer Function Testing of an Oxidizer Turbo-Pump Combined Inducer and Impeller

NASA Technical Reports Server (NTRS)

Karon, D. M.; Patel, S. K.; Zoladz, T. F.

2016-01-01

In 2009 and 2010, Concepts NREC prepared for and performed a series of tests on a 52% scale of a version of the Pratt & Whitney Rocketdyne J-2X Oxidizer Turbopump under a Phase III SBIR with NASA MSFC. The test article was a combined inducer and impeller, tested as a unit. This paper presents an overview of the test rig and facility, instrumentation, signal conditioning, data acquisition systems, testing approach, measurement developments, and lessons learned. Results from these tests were presented in the form of two papers at the previous JANNAF joint propulsion conference, in December of 2011.

Integration of ground-penetrating radar, ultrasonic tests and infrared thermography for the analysis of a precious medieval rose window

NASA Astrophysics Data System (ADS)

Nuzzo, L.; Calia, A.; Liberatore, D.; Masini, N.; Rizzo, E.

2010-04-01

The integration of high-resolution, non-invasive geophysical techniques (such as ground-penetrating radar or GPR) with emerging sensing techniques (acoustics, thermography) can complement limited destructive tests to provide a suitable methodology for a multi-scale assessment of the state of preservation, material and construction components of monuments. This paper presents the results of the application of GPR, infrared thermography (IRT) and ultrasonic tests to the 13th century rose window of Troia Cathedral (Apulia, Italy), affected by widespread decay and instability problems caused by the 1731 earthquake and reactivated by recent seismic activity. This integrated approach provided a wide amount of complementary information at different scales, ranging from the sub-centimetre size of the metallic joints between the various architectural elements, narrow fractures and thin mortar fillings, up to the sub-metre scale of the internal masonry structure of the circular ashlar curb linking the rose window to the façade, which was essential to understand the original building technique and to design an effective restoration strategy.

The Effects of Sleep Deprivation on Dissociation and Profiles of Mood, and Its Association with Biochemical Changes

PubMed Central

SELVİ, Yavuz; KILIÇ, Sultan; AYDIN, Adem; GÜZEL ÖZDEMİR, Pınar

2015-01-01

Introduction Sleep deprivation is a method, which has being used in order to comprehend the functions of sleep both in healthy individuals and for the patients of depression with in treatment, for a long time. The objective of our present study is to examine the relation between hormonal values, which are known for being related to the effects of these said changes determined in the mood, dissociation and thought suppression in healthy individuals after one night of sleep deprivation implementation. Methods One night sleep deprivation was performed on a total of thirty-two healthy volunteers (16 males and 16 females) who were included in the study. Blood samples were taken from the individuals before and after sleep deprivation implementation in order to determine cortisol, dehydroepiandrosterone-sulfate (DHEA-S) and Thyroid Functions’ Levels tests. In order to evaluate the effects of the sleep deprivation on moods, “White Bear Suppression Inventory (WBSI)” has been conducted, with an aim of evaluating thought suppression, “Profile of Mood States (POMS)”, “Dissociative Experiences Scale (DES)” with a purpose of realizing any dissociation tendency. Results On the individuals who have been implemented for sleep deprivation, a decrease on depression and vigor-activity sub-scales values was detected, and an increase was determined on fatigue sub-scales values of “POMS”. While the values of DES were found to have been statistically increased after sleep deprivation, also a significant decrease was determined on WBSI values. Even if there hasn’t been any significant statistical change determined on cortisol levels after sleep deprivation, yet there had been some significant changes detected on Thyroid Stimulating Hormone (TSH), fT3, fT4, and DHEA-S levels. Decrease in “POMS” depression sub-scale values and increase on fatigue sub-scale values were determined on the individuals whose sT4 levels were found to be increased significantly in statistic manner after the sleep deprivation. Conclusion According to the results of our study, sleep deprivation for one night was determined to cause decrease on depressive mood, increase on dissociative symptoms and to lower the tendency of suppressing the unwanted thoughts, consciously. The fact of being obtained lower depression values, on the individuals with the increased DHEA-S levels after the sleep deprivation meets with the information claiming that the high DHEA-S levels may be deemed as protectors against the negative effects of the stress. PMID:28360682

A direct comparison of U.S. Environmental Protection Agency's method 304B and batch tests for determining activated-sludge biodegradation rate constants for volatile organic compounds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cano, M.L.; Wilcox, M.E.; Compernolle, R. van

Biodegradation rate constants for volatile organic compounds (VOCs) in activated-sludge systems are needed to quantify emissions. One current US environmental Protection Agency method for determining a biodegradation rate constant is Method 304B. In this approach, a specific activated-sludge unit is simulated by a continuous biological treatment system with a sealed headspace. Batch experiments, however, can be alternatives to Method 304B. Two of these batch methods are the batch test that uses oxygen addition (BOX) and the serum bottle test (SBT). In this study, Method 304B was directly compared to BOX and SBT experiments. A pilot-scale laboratory reactor was constructed tomore » serve as the Method 304B unit. Biomass from the unit was also used to conduct BOX and modified SBT experiments (modification involved use of a sealed draft-tube reactor with a headspace recirculation pump instead of a serum bottle) for 1,2-dichloroethane, diisopropyl ether, methyl tertiary butyl ether, and toluene. Three experimental runs--each consisting of one Method 304B experiment, one BOX experiment, and one modified SBT experiment--were completed. The BOX and SBT data for each run were analyzed using a Monod model, and best-fit biodegradation kinetic parameters were determined for each experiment, including a first-order biodegradation rate constant (K{sub 1}). Experimental results suggest that for readily biodegradable VOCs the two batch techniques can provide improved means of determining biodegradation rate constants compared with Method 304B. In particular, these batch techniques avoid the Method 304B problem associated with steady-state effluent concentrations below analytical detection limits. However, experimental results also suggest that the two batch techniques should not be used to determine biodegradation rate constants for slowly degraded VOCs (i.e., K{sub 1} {lt} 0.1 L/g VSS-h).« less

Sub-ply level scaling approach investigated for graphite-epoxy composite beam columns

NASA Technical Reports Server (NTRS)

Jackson, Karen E.; Kellas, Sotiris

1994-01-01

Scale model graphite-epoxy composite specimens were fabricated using the 'sub-ply level' approach and tested as beam-columns under an eccentric axial load to determine the effect of specimen size on flexural response and failure. In the current research project, although the fiber diameters are not scaled, the thickness of the pre-preg material itself has been scaled by adjusting the number of fibers through the thickness of a single ply. Three different grades of graphite-epoxy composite material (AS4/3502) were obtained from Hercules, Inc., in which the number of fibers through the thickness of a single ply was reduced (Grade 190 with 12 to 16 fibers, Grade 95 with 6 to 8 fibers, and Grade 48 with 3 to 4 fibers). Thus, using the sub-ply level approach, a baseline eight ply quasi-isotropic laminate could be fabricated using either the Grade 48 or Grade 95 material and the corresponding full-scale laminate would be constructed from Grade 95 or standard Grade 190 material, respectively. Note that in the sub-ply level approach, the number of ply interfaces is constant for the baseline and full-scale laminates. This is not true for the ply level and sublaminate level scaled specimens. The three grades of graphite-epoxy composite material were used to fabricate scale model beam-column specimens with in-plane dimensions of 0.5*n x 5.75*n, where n=1,2,4 corresponsing to 1/4, 1/2, and full-scale factors. Angle ply, cross ply, and quasi-isotropic laminate stacking sequences were chosen for the investigation and the test matrices for each laminate type are given. Specimens in each laminate family with the same in-plane dimensions but different thicknesses were tested to isolate the influence of the thickness dimension on the flexural response and failure. Also, specific lay-ups were chosen with blocked plies and dispersed plies for each laminate type. Specimens were subjected to an eccentric axial load until failure. The load offset was introduced through a set of hinges which were attached to the platens of a standard load test machine. Three sets of geometrically scaled hinges were used to ensure that scaled loading conditions were applied. This loading condition was chosen because it promotes large flexural deformations and specimens fail at the center of the beam, away from the grip supports. Five channels of data including applied vertical load, end shortening displacement, strain from gages applied back-to-back at the midspan of the beam, and rotation of the hinge from a bubble inclinometer were recorded for each specimen. The beam-column test configuration was used previously to study size effects in ply level scaled composite specimens of the same material system, sizes, and stacking sequences. Thus, a direct comparison between the two scaling approaches is possible. Ply level scaled beam-columns with angle ply, cross ply, and quasi-isotropic lay-ups exhibited no size dependencies in the flexural response, but significant size effects in strength. The reduction in strength with increasing specimen size was not predicted successfully by analysis techniques. It is anticipated that results from this investigation will lead to a better understanding of the strength scale effect in composite structures.

Predicted Sensitivity for Tests of Short-range Gravity with a Novel Parallel-plate Torsion Pendulum

NASA Astrophysics Data System (ADS)

Richards, Matthew; Baxley, Brandon; Hoyle, C. D.; Leopardi, Holly; Shook, David

2011-11-01

The parallel-plate torsion pendulum apparatus at Humboldt State University is designed to test the Weak Equivalence Principle (WEP) and the gravitational inverse-square law (ISL) of General Relativity at unprecedented levels in the sub-millimeter regime. Some versions of String Theory predict additional dimensions that might affect the gravitational inverse-square law (ISL) at sub-millimeter levels. Some models also predict the existence of unobserved subatomic particles, which if exist, could cause a violation in the WEP at short distances. Short-range tests of gravity and the WEP are also instrumental in investigating possible proposed mechanisms that attempt to explain the accelerated expansion of the universe, generally attributed to Dark Energy. The weakness of the gravitational force makes measurement very difficult at small scales. Testing such a minimal force requires highly isolated experimental systems and precise measurement and control instrumentation. Moreover, a dedicated test of the WEP has not been performed below the millimeter scale. This talk will discuss the improved sensitivity that we expect to achieve in short-range gravity tests with respect to previous efforts that employ different experimental configurations.

Synthesis of monodispersed ZnAl{sub 2}O{sub 4} nanoparticles and their tribology properties as lubricant additives

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Xiaoyun; Zheng, Shaohua; Zhang, Jun

Graphical abstract: Display Omitted Highlights: ► The preparation of ZnAl{sub 2}O{sub 4} nanoparticles was realized by hydrothermal method. ► After surface modification, ZnAl{sub 2}O{sub 4} nanoparticles of narrow size distribution can disperse in lubricating oil stably. ► The modified ZnAl{sub 2}O{sub 4} nanoparticles as lubricating oil additives exhibit good tribology properties. -- Abstract: Monodispersed spherical zinc aluminate spinel (ZnAl{sub 2}O{sub 4}) nanoparticles were synthesized via a solvothermal method and modified by oleic acid in cyclohexanol solution. The nanoparticles were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and infrared spectrum (IR). The dispersion ability of nanoparticles in lubricant oilmore » was measured with optical absorbance spectrum. The results show that the modified nanoparticles are nearly monodispersed and can stably disperse in lubricant oil. The tribological properties of the ZnAl{sub 2}O{sub 4} nanoparticles as an additive in lubricant oil were evaluated with four-ball test and thrust-ring test. For comparison, ZnO and Al{sub 2}O{sub 3} nanoparticles as additive in lubricant oil were also tested respectively. The results show that ZnAl{sub 2}O{sub 4} nanoparticles exhibit better tribology properties in terms of anti-wear and anti-friction than ZnO or Al{sub 2}O{sub 3} nanoparticles. The anti-friction and anti-wear mechanisms were discussed and the lubricating effect of ZnAl{sub 2}O{sub 4} nanoparticles can be attributed to nano-bearings effect and tribo-sintering mechanism.« less

FUEL-FLEXIBLE GASIFICATION-COMBUSTION TECHNOLOGY FOR PRODUCTION OF H2 AND SEQUESTRATION-READY CO2

DOE Office of Scientific and Technical Information (OSTI.GOV)

George Rizeq; Janice West; Arnaldo Frydman

It is expected that in the 21st century the Nation will continue to rely on fossil fuels for electricity, transportation, and chemicals. It will be necessary to improve both the process efficiency and environmental impact performance of fossil fuel utilization. GE Global Research has developed an innovative fuel-flexible Unmixed Fuel Processor (UFP) technology to produce H{sub 2}, power, and sequestration-ready CO{sub 2} from coal and other solid fuels. The UFP module offers the potential for reduced cost, increased process efficiency relative to conventional gasification and combustion systems, and near-zero pollutant emissions including NO{sub x}. GE Global Research (prime contractor) wasmore » awarded a contract from U.S. DOE NETL to develop the UFP technology. Work on this Phase I program started on October 1, 2000. The project team includes GE Global Research, Southern Illinois University at Carbondale (SIU-C), California Energy Commission (CEC), and T. R. Miles, Technical Consultants, Inc. In the UFP technology, coal and air are simultaneously converted into separate streams of (1) high-purity hydrogen that can be utilized in fuel cells or turbines, (2) sequestration-ready CO{sub 2}, and (3) high temperature/pressure vitiated air to produce electricity in a gas turbine. The process produces near-zero emissions and, based on ASPEN Plus process modeling, has an estimated process efficiency of 6% higher than IGCC with conventional CO{sub 2} separation. The current R&D program will determine the feasibility of the integrated UFP technology through pilot-scale testing, and will investigate operating conditions that maximize separation of CO{sub 2} and pollutants from the vent gas, while simultaneously maximizing coal conversion efficiency and hydrogen production. The program integrates experimental testing, modeling and economic studies to demonstrate the UFP technology. This is the thirteenth quarterly technical progress report for the UFP program, which is supported by U.S. DOE NETL under Contract No. DE-FC26-00FT40974. This report summarizes program accomplishments for the period starting October 1, 2003 and ending December 31, 2003. The report includes an introduction summarizing the UFP technology, main program tasks, and program objectives; it also provides a summary of program activities and accomplishments covering progress in tasks including lab-scale experimental testing, pilot-scale assembly, pilot-scale demonstration and program management and technology transfer.« less

Coal feed component testing for CDIF

NASA Technical Reports Server (NTRS)

Pearson, C. V.; Snyder, B. K.; Fornek, T. E.

1977-01-01

Investigations conducted during the conceptual design of the Montana MHD Component Development and Integration Facility (CDIF) identified commercially available processing and feeding equipment potentially suitable for use in a reference design. Tests on sub-scale units of this equipment indicated that they would perform as intended.

3D granulometry: grain-scale shape and size distribution from point cloud dataset of river environments

NASA Astrophysics Data System (ADS)

Steer, Philippe; Lague, Dimitri; Gourdon, Aurélie; Croissant, Thomas; Crave, Alain

2016-04-01

The grain-scale morphology of river sediments and their size distribution are important factors controlling the efficiency of fluvial erosion and transport. In turn, constraining the spatial evolution of these two metrics offer deep insights on the dynamics of river erosion and sediment transport from hillslopes to the sea. However, the size distribution of river sediments is generally assessed using statistically-biased field measurements and determining the grain-scale shape of river sediments remains a real challenge in geomorphology. Here we determine, with new methodological approaches based on the segmentation and geomorphological fitting of 3D point cloud dataset, the size distribution and grain-scale shape of sediments located in river environments. Point cloud segmentation is performed using either machine-learning algorithms or geometrical criterion, such as local plan fitting or curvature analysis. Once the grains are individualized into several sub-clouds, each grain-scale morphology is determined using a 3D geometrical fitting algorithm applied on the sub-cloud. If different geometrical models can be conceived and tested, only ellipsoidal models were used in this study. A phase of results checking is then performed to remove grains showing a best-fitting model with a low level of confidence. The main benefits of this automatic method are that it provides 1) an un-biased estimate of grain-size distribution on a large range of scales, from centimeter to tens of meters; 2) access to a very large number of data, only limited by the number of grains in the point-cloud dataset; 3) access to the 3D morphology of grains, in turn allowing to develop new metrics characterizing the size and shape of grains. The main limit of this method is that it is only able to detect grains with a characteristic size greater than the resolution of the point cloud. This new 3D granulometric method is then applied to river terraces both in the Poerua catchment in New-Zealand and along the Laonong river in Taiwan, which point clouds were obtained using both terrestrial lidar scanning and structure from motion photogrammetry.

Visible Motion Blur

NASA Technical Reports Server (NTRS)

Watson, Andrew B. (Inventor); Ahumada, Albert J. (Inventor)

2014-01-01

A method of measuring motion blur is disclosed comprising obtaining a moving edge temporal profile r(sub 1)(k) of an image of a high-contrast moving edge, calculating the masked local contrast m(sub1)(k) for r(sub 1)(k) and the masked local contrast m(sub 2)(k) for an ideal step edge waveform r(sub 2)(k) with the same amplitude as r(sub 1)(k), and calculating the measure or motion blur Psi as a difference function, The masked local contrasts are calculated using a set of convolution kernels scaled to simulate the performance of the human visual system, and Psi is measured in units of just-noticeable differences.

Perceptions of nursing students of educational environment at a private undergraduate School of Nursing in Karachi.

PubMed

Farooq, Salima; Rehman, Rehana; Hussain, Mehwish; Dias, Jacqueline Maria

2018-02-01

To assess educational environment at a nursing school.. The cross-sectional survey was carried out from May to October 2016 at Aga Khan University School of Nursing and Midwifery, Karachi, using the Dundee Ready Educational Environment Measure tool. The scores were obtained by merging five sub-scales of the inventory. The average scores of the scale and sub-scales were compared in terms of age, year of study, and living status using Mann-Whitney U test, and among years of study by Kruskal Wallis test.. Of the 442 students, 228(51.6%) had age below 20 years. Overall, 131(29.1%) subjects were in the first year, 152(33.8%) second year, 91(20.2%) third year and 76(16.9%) fourth year. The average Dundee Ready Educational Environment Measure score was 129.92±19.97 with reliability of 88.9%. Students aged 20 years and less had more positive perceptions than students over 20 years (p<0.0001). Students living in hostel secured higher scores (p<0.0001). First year nursing students attained significant highest scores in all sub-scales compared to the rest (p<0.0001). Scores reveal better perception from younger nursing students, as well as those living in the hostel and those who were in their initial years of nursing education.

HMM-ModE: implementation, benchmarking and validation with HMMER3

PubMed Central

2014-01-01

Background HMM-ModE is a computational method that generates family specific profile HMMs using negative training sequences. The method optimizes the discrimination threshold using 10 fold cross validation and modifies the emission probabilities of profiles to reduce common fold based signals shared with other sub-families. The protocol depends on the program HMMER for HMM profile building and sequence database searching. The recent release of HMMER3 has improved database search speed by several orders of magnitude, allowing for the large scale deployment of the method in sequence annotation projects. We have rewritten our existing scripts both at the level of parsing the HMM profiles and modifying emission probabilities to upgrade HMM-ModE using HMMER3 that takes advantage of its probabilistic inference with high computational speed. The method is benchmarked and tested on GPCR dataset as an accurate and fast method for functional annotation. Results The implementation of this method, which now works with HMMER3, is benchmarked with the earlier version of HMMER, to show that the effect of local-local alignments is marked only in the case of profiles containing a large number of discontinuous match states. The method is tested on a gold standard set of families and we have reported a significant reduction in the number of false positive hits over the default HMM profiles. When implemented on GPCR sequences, the results showed an improvement in the accuracy of classification compared with other methods used to classify the familyat different levels of their classification hierarchy. Conclusions The present findings show that the new version of HMM-ModE is a highly specific method used to differentiate between fold (superfamily) and function (family) specific signals, which helps in the functional annotation of protein sequences. The use of modified profile HMMs of GPCR sequences provides a simple yet highly specific method for classification of the family, being able to predict the sub-family specific sequences with high accuracy even though sequences share common physicochemical characteristics between sub-families. PMID:25073805

Mixed-Mode Bending Method for Delamination Testing

NASA Technical Reports Server (NTRS)

Reeder, James R.; Crews, John R., Jr.

1990-01-01

A mixed mode delamination test procedure was developed combining double cantilever beam (DCB) mode I loading and end-notch fixture (ENF) mode II loading on a split unidirectional laminate. By loading with a lever, a single applied load simultaneously produces mode I and mode II bending loads on the specimen. This mixed-mode bending (MMB) test was analyzed using both finite-element procedures and beam theory to calculate the mode I and mode II components of strain-energy release rate G(sub I) and G(sub II), respectively. A wide range of G(sub I)/G(sub II) ratios can be produced by varying the load position on the lever. As the delamination extended, the G(sub I)/G(sub II) ratios varied by less than 5%. Beam theory equations agreed closely with the finite-element results and provide a basis for selection of G(sub I)/G(sub II) test ratios and a basis for computing the mode I and mode II components of measured delamination toughness. The MMB test was demonstrated using AS4/PEEK (APC2) unidirectional laminates. The MMB test introduced in this paper is rather simple and is believed to offer several advantages over most current mixed-mode test.

Using the Climbing Drum Peel (CDP) Test to Obtain a G(sub IC) value for Core/Facesheet Bonds

NASA Technical Reports Server (NTRS)

Nettles, A. T.; Gregory, Elizabeth D.; Jackson, Justin R.

2006-01-01

A method of measuring the Mode I fracture toughness of core/facesheet bonds in sandwich Structures is desired, particularly with the widespread use of models that need this data as input. This study examined if a critical strain energy release rate, G(sub IC), can be obtained from the climbing drum peel (CDP) test. The CDP test is relatively simple to perform and does not rely on measuring small crack lengths such as required by the double cantilever beam (DCB) test. Simple energy methods were used to calculate G(sub IC) from CDP test data on composite facesheets bonded to a honeycomb core. Facesheet thicknesses from 2 to 5 plies were tested to examine the upper and lower bounds on facesheet thickness requirements. Results from the study suggest that the CDP test, with certain provisions, can be used to find the GIG value of a core/facesheet bond.

SUMMARY TECHNICAL REPORT FOR THE PERIOD JANUARY 1, 1961-MARCH 31, 1961

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burgett, R. ed

1961-05-01

Uranium and TBP Recovery from Waste Solvent. Laboratory and pilot-scale tests were carried out which demonstrated (1) that uranium in waste solvent can be removed by slurrying the solvent with activated charcoal, filtering the slurry, and washing the slurry with water and 3% Na/sub 2/CO/sub 3/ and (2) that TBP can be recovered from the waste solvent by splitting the solvent with HCl and distilling the TBP-rich phase. Improvement of Green Salt Quality. Denitration of ammonium uranyl trinitrate yielded a light, finely divided form of gamma -UO/ sub 3/ with a surface area higher than that of conventional batch potmore » powder; however, its reactivity in reduction and hydrofluorination tests was only moderately higher in comparison. Oxidation-reduction cycles were found to increase the reactivity of UO/sub 2/ toward hydrofluorination. The properties of various UO/sub 2/ samples were determined and correlated with the preparative methods used. Dehydration of Winlo Green Salt. About 27 tons of Winlo green salt was successfully dehydrated to a water content of -0.04% in a hydrofluorination reactor bank in the Green Salt Plant. Recovery of Uranium from MgF/sub 2/ Slag. A process for continuously digesting MgF/sub 2/ slag for uranium recovery was successfully tested on a plant scale. In this process, a water slurry of slag is transferred at a fixed rate and reacted with HCl, and the controlled feed rate reduces the hydrogen concentration. Graphite Liner for Bomb Reduction of Green Salt. An evaluation was made on machined graphite as a replacement for jolt-packed MgF/sub 2/ presently used to line reduction vessels for uranium metal production. Best results were obtained with a onepiece graphite liner fitted inside a steel vessel with an annulus of MgF/sub 2/ between liner and pot. Effects of Feed Material on Ingot Chemical Purity and Yields. The effects of various types of uranium feed stock on the chemical purity and yield of ingots were studied. The following results were obtained: (1) The H content was higher in ingots cast from melts contairing more derby material, (2) the O, N, and C contents of samples from ingot tops were signiicantly lower than those from ingot bottoms, (3) the crude ingot yields were lowest for pigots, briquettes, and heat-shocked grade III derbies, (4) pigots were deleterious to ingot chemical purity, (5) degreased drip crops and dingot extrnsion scrap were deleterious to core-to-good-core yield. Alpha Annealing of Uranium. The effect of a high alpha temperature anneal on the structure and growin index of beta heat treated uranium was evaluated. It was found that longer alpha annealing times gave greater recrystallization and that higher temperatures gave more rapid recrystallization. Delays of up to 6 months between beta heat treatment and alpha anneal did not affect either the recrystallization or the growth index. Billet Drilling. A LeBlond-Carlstedt Rapid Borer was tested as a urarium billet drilling machine and found to give satisfactory results, although some tool breakage occurred. (D.L.C.)« less

Standard test method for nitrogen dioxide content of the atmosphere (Griess--Saltzman reaction)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1977-01-01

A spectrophotometric method for the determination of NO/sub 2/ in the atmosphere is described. The NO/sub 2/ is absorbed in an azo-dye forming reagent, and a red-violet color is measured spectrophotometrically at 550 nm. The NO/sub 2/ is sampled through fritted-tip bubblers, and concentrations of NO/sub 2/ in the atmosphere from 4 to 10,000 ..mu..g/m/sup 3/ can be determined.

CO{sub 2} Reuse in Petrochemical Facilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jason Trembly; Brian Turk; Maruthi Pavani

2010-12-31

To address public concerns regarding the consequences of climate change from anthropogenic carbon dioxide (CO{sub 2}) emissions, the U.S. Department of Energy's National Energy Technology Laboratory (DOE/NETL) is actively funding a CO{sub 2} management program to develop technologies capable of mitigating CO{sub 2} emissions from power plant and industrial facilities. Over the past decade, this program has focused on reducing the costs of carbon capture and storage technologies. Recently, DOE/NETL launched an alternative CO{sub 2} mitigation program focused on beneficial CO{sub 2} reuse to support the development of technologies that mitigate emissions by converting CO{sub 2} into valuable chemicals andmore » fuels. RTI, with DOE/NETL support, has been developing an innovative beneficial CO{sub 2} reuse process for converting CO{sub 2} into substitute natural gas (SNG) by using by-product hydrogen (H{sub 2)-containing fuel gas from petrochemical facilities. This process leveraged commercial reactor technology currently used in fluid catalytic crackers in petroleum refining and a novel nickel (Ni)-based catalyst developed by RTI. The goal was to generate an SNG product that meets the pipeline specifications for natural gas, making the SNG product completely compatible with the existing natural gas infrastructure. RTI's technology development efforts focused on demonstrating the technical feasibility of this novel CO{sub 2} reuse process and obtaining the necessary engineering information to design a pilot demonstration unit for converting about 4 tons per day (tons/day) of CO{sub 2} into SNG at a suitable host site. This final report describes the results of the Phase I catalyst and process development efforts. The methanation activity of several commercial fixed-bed catalysts was evaluated under fluidized-bed conditions in a bench-scale reactor to identify catalyst performance targets. RTI developed two fluidizable Ni-based catalyst formulations (Cat-1 and Cat-3) that demonstrated equal or better performance than that of commercial methanation catalysts. The Cat-1 and Cat-3 formulations were successfully scaled up using commercial manufacturing equipment at the Sud-Chemie Inc. pilot-plant facility in Louisville, KY. Pilot transport reactor testing with RTI's Cat-1 formulation at Kellog Brown & Root's Technology Center demonstrated the ability of the process to achieve high single-pass CO{sub 2} conversion. Using information acquired from bench- and pilot-scale testing, a basic engineering design package was prepared for a 4-ton/day CO{sub 2} pilot demonstration unit, including process and instrumentation diagrams, equipment list, control philosophy, and preliminary cost estimate.« less

Commercialization Development of Oxygen Fired CFB for Greenhouse Gas Control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nsakala ya Nsakala; Gregory N. Liljedahl; David G. Turek

2007-03-31

Given that fossil fuel fired power plants are among the largest and most concentrated producers of CO{sub 2} emissions, recovery and sequestration of CO{sub 2} from the flue gas of such plants has been identified as one of the primary means for reducing anthropogenic (i.e., man-made) CO{sub 2} emissions. In 2001, ALSTOM Power Inc. (ALSTOM) began a two-phase program to investigate the feasibility of various carbon capture technologies. This program was sponsored under a Cooperative Agreement from the US Department of Energy's National Energy Technology Laboratory (DOE). The first phase entailed a comprehensive study evaluating the technical feasibility and economicsmore » of alternate CO{sub 2} capture technologies applied to Greenfield US coal-fired electric generation power plants. Thirteen cases, representing various levels of technology development, were evaluated. Seven cases represented coal combustion in CFB type equipment. Four cases represented Integrated Gasification Combined Cycle (IGCC) systems. Two cases represented advanced Chemical Looping Combined Cycle systems. Marion, et al. reported the details of this work in 2003. One of the thirteen cases studied utilized an oxygen-fired circulating fluidized bed (CFB) boiler. In this concept, the fuel is fired with a mixture of oxygen and recirculated flue gas (mainly CO{sub 2}). This combustion process yields a flue gas containing over 80 percent (by volume) CO{sub 2}. This flue gas can be processed relatively easily to enrich the CO{sub 2} content to over 96 percent for use in enhanced oil or gas recovery (EOR or EGR) or simply dried for sequestration. The Phase I study identified the O{sub 2}-fired CFB as having a near term development potential, because it uses conventional commercial CFB technology and commercially available CO{sub 2} capture enabling technologies such as cryogenic air separation and simple rectification or distillation gas processing systems. In the long term, air separation technology advancements offer significant reductions in power requirements, which would improve plant efficiency and economics for the oxygen-fired technology. The second phase consisted of pilot-scale testing followed by a refined performance and economic evaluation of the O{sub 2} fired CFB concept. As a part of this workscope, ALSTOM modified its 3 MW{sub th} (9.9 MMBtu/hr) Multiuse Test Facility (MTF) pilot plant to operate with O{sub 2}/CO{sub 2} mixtures of up to 70 percent O{sub 2} by volume. Tests were conducted with coal and petroleum coke. The test objectives were to determine the impacts of oxygen firing on heat transfer, bed dynamics, potential agglomeration, and gaseous and particulate emissions. The test data results were used to refine the design, performance, costs, and economic models developed in Phase-I for the O{sub 2}-fired CFB with CO{sub 2} capture. Nsakala, Liljedahl, and Turek reported results from this study in 2004. ALSTOM identified several items needing further investigation in preparation for large scale demonstration of the oxygen-fired CFB concept, namely: (1) Operation and performance of the moving bed heat exchanger (MBHE) to avoid recarbonation and also for cost savings compared to the standard bubbling fluid bed heat exchanger (FBHE); (2) Performance of the back-end flash dryer absorber (FDA) for sulfur capture under high CO{sub 2}/high moisture flue gas environment using calcined limestone in the fly ash and using fresh commercial lime directly in the FDA; (3) Determination of the effect of recarbonation on fouling in the convective pass; (4) Assessment of the impact of oxygen firing on the mercury, other trace elements, and volatile organic compound (VOC) emissions; and (5) Develop a proposal-level oxygen-fired retrofit design for a relatively small existing CFB steam power plant in preparation for a large-scale demonstration of the O{sub 2} fired CFB concept. Hence, ALSTOM responded to a DOE Solicitation to address all these issues with further O{sub 2} fired MTF pilot testing and a subsequent retrofit design study of oxygen firing and CO{sub 2} capture on an existing air-fired CFB plant. ALSTOM received a contract award from the DOE to conduct a project entitled 'Commercialization Development of Oxygen Fired CFB for Greenhouse Gas Control', under Cooperative Agreement DE-FC26-04NT42205 that is the subject of this topical report.« less

Probing sub-alveolar length scales with hyperpolarized-gas diffusion NMR

NASA Astrophysics Data System (ADS)

Miller, Wilson; Carl, Michael; Mooney, Karen; Mugler, John; Cates, Gordon

2009-05-01

Diffusion MRI of the lung is a promising technique for detecting alterations of normal lung microstructure in diseases such as emphysema. The length scale being probed using this technique is related to the time scale over which the helium-3 or xenon-129 diffusion is observed. We have developed new MR pulse sequence methods for making diffusivity measurements at sub-millisecond diffusion times, allowing one to probe smaller length scales than previously possible in-vivo, and opening the possibility of making quantitative measurements of the ratio of surface area to volume (S/V) in the lung airspaces. The quantitative accuracy of simulated and experimental measurements in microstructure phantoms will be discussed, and preliminary in-vivo results will be presented.

System-Integrated Finite Element Analysis of a Full-Scale Helicopter Crash Test with Deployable Energy Absorbers

NASA Technical Reports Server (NTRS)

Annett, Martin S.; Polanco, Michael A.

2010-01-01

A full-scale crash test of an MD-500 helicopter was conducted in December 2009 at NASA Langley's Landing and Impact Research facility (LandIR). The MD-500 helicopter was fitted with a composite honeycomb Deployable Energy Absorber (DEA) and tested under vertical and horizontal impact velocities of 26-ft/sec and 40-ft/sec, respectively. The objectives of the test were to evaluate the performance of the DEA concept under realistic crash conditions and to generate test data for validation of a system integrated finite element model. In preparation for the full-scale crash test, a series of sub-scale and MD-500 mass simulator tests was conducted to evaluate the impact performances of various components, including a new crush tube and the DEA blocks. Parameters defined within the system integrated finite element model were determined from these tests. The objective of this paper is to summarize the finite element models developed and analyses performed, beginning with pre-test predictions and continuing through post-test validation.

LS-DYNA Analysis of a Full-Scale Helicopter Crash Test

NASA Technical Reports Server (NTRS)

Annett, Martin S.

2010-01-01

A full-scale crash test of an MD-500 helicopter was conducted in December 2009 at NASA Langley's Landing and Impact Research facility (LandIR). The MD-500 helicopter was fitted with a composite honeycomb Deployable Energy Absorber (DEA) and tested under vertical and horizontal impact velocities of 26 ft/sec and 40 ft/sec, respectively. The objectives of the test were to evaluate the performance of the DEA concept under realistic crash conditions and to generate test data for validation of a system integrated LS-DYNA finite element model. In preparation for the full-scale crash test, a series of sub-scale and MD-500 mass simulator tests was conducted to evaluate the impact performances of various components, including a new crush tube and the DEA blocks. Parameters defined within the system integrated finite element model were determined from these tests. The objective of this paper is to summarize the finite element models developed and analyses performed, beginning with pre-test and continuing through post test validation.

Verification of Ceramic Structures

NASA Astrophysics Data System (ADS)

Behar-Lafenetre, Stephanie; Cornillon, Laurence; Rancurel, Michael; De Graaf, Dennis; Hartmann, Peter; Coe, Graham; Laine, Benoit

2012-07-01

In the framework of the “Mechanical Design and Verification Methodologies for Ceramic Structures” contract [1] awarded by ESA, Thales Alenia Space has investigated literature and practices in affiliated industries to propose a methodological guideline for verification of ceramic spacecraft and instrument structures. It has been written in order to be applicable to most types of ceramic or glass-ceramic materials - typically Cesic®, HBCesic®, Silicon Nitride, Silicon Carbide and ZERODUR®. The proposed guideline describes the activities to be performed at material level in order to cover all the specific aspects of ceramics (Weibull distribution, brittle behaviour, sub-critical crack growth). Elementary tests and their post-processing methods are described, and recommendations for optimization of the test plan are given in order to have a consistent database. The application of this method is shown on an example in a dedicated article [7]. Then the verification activities to be performed at system level are described. This includes classical verification activities based on relevant standard (ECSS Verification [4]), plus specific analytical, testing and inspection features. The analysis methodology takes into account the specific behaviour of ceramic materials, especially the statistical distribution of failures (Weibull) and the method to transfer it from elementary data to a full-scale structure. The demonstration of the efficiency of this method is described in a dedicated article [8]. The verification is completed by classical full-scale testing activities. Indications about proof testing, case of use and implementation are given and specific inspection and protection measures are described. These additional activities are necessary to ensure the required reliability. The aim of the guideline is to describe how to reach the same reliability level as for structures made of more classical materials (metals, composites).

Study on the Validity and Reliability of Melbourne Decision Making Scale in Turkey

ERIC Educational Resources Information Center

Çolakkadioglu, Oguzhan; Deniz, M. Engin

2015-01-01

This study is to analyze the validity and reliability of Melbourne Decision Making Questionnaire (MDMQ). The sample consisted of 650 university students. The structural validity of the MDMQ, as well as correlations among its sub-scales, measure-bound validity, internal consistency, item total correlations and test-retest reliability coefficients…

Kilovoltage cone-beam CT: Comparative dose and image quality evaluations in partial and full-angle scan protocols

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Sangroh; Yoo, Sua; Yin Fangfang

2010-07-15

Purpose: To assess imaging dose of partial and full-angle kilovoltage CBCT scan protocols and to evaluate image quality for each protocol. Methods: The authors obtained the CT dose index (CTDI) of the kilovoltage CBCT protocols in an on-board imager by ion chamber (IC) measurements and Monte Carlo (MC) simulations. A total of six new CBCT scan protocols were evaluated: Standard-dose head (100 kVp, 151 mA s, partial-angle), low-dose head (100 kVp, 75 mA s, partial-angle), high-quality head (100 kVp, 754 mA s, partial-angle), pelvis (125 kVp, 706 mA s, full-angle), pelvis spotlight (125 kVp, 752 mA s, partial-angle), and low-dosemore » thorax (110 kVp, 271 mA s, full-angle). Using the point dose method, various CTDI values were calculated by (1) the conventional weighted CTDI (CTDI{sub w}) calculation and (2) Bakalyar's method (CTDI{sub wb}). The MC simulations were performed to obtain the CTDI{sub w} and CTDI{sub wb}, as well as from (3) central slice averaging (CTDI{sub 2D}) and (4) volume averaging (CTDI{sub 3D}) techniques. The CTDI values of the new protocols were compared to those of the old protocols (full-angle CBCT protocols). Image quality of the new protocols was evaluated following the CBCT image quality assurance (QA) protocol [S. Yoo et al., ''A quality assurance program for the on-board imager registered ,'' Med. Phys. 33(11), 4431-4447 (2006)] testing Hounsfield unit (HU) linearity, spatial linearity/resolution, contrast resolution, and HU uniformity. Results: The CTDI{sub w} were found as 6.0, 3.2, 29.0, 25.4, 23.8, and 7.7 mGy for the new protocols, respectively. The CTDI{sub w} and CTDI{sub wb} differed within +3% between IC measurements and MC simulations. Method (2) results were within {+-}12% of method (1). In MC simulations, the CTDI{sub w} and CTDI{sub wb} were comparable to the CTDI{sub 2D} and CTDI{sub 3D} with the differences ranging from -4.3% to 20.6%. The CTDI{sub 3D} were smallest among all the CTDI values. CTDI{sub w} of the new protocols were found as {approx}14 times lower for standard head scan and 1.8 times lower for standard body scan than the old protocols, respectively. In the image quality QA tests, all the protocols except low-dose head and low-dose thorax protocols were within the tolerance in the HU verification test. The HU value for the two protocols was always higher than the nominal value. All the protocols passed the spatial linearity/resolution and HU uniformity tests. In the contrast resolution test, only high-quality head and pelvis scan protocols were within the tolerance. In addition, crescent effect was found in the partial-angle scan protocols. Conclusions: The authors found that CTDI{sub w} of the new CBCT protocols has been significantly reduced compared to the old protocols with acceptable image quality. The CTDI{sub w} values in the point dose method were close to the volume averaging method within 9%-21% for all the CBCT scan protocols. The Bakalyar's method produced more accurate dose estimation within 14%. The HU inaccuracy from low-dose head and low-dose thorax protocols can render incorrect dose results in the treatment planning system. When high soft-tissue contrast data are desired, high-quality head or pelvis scan protocol is recommended depending on the imaging area. The point dose method can be applicable to estimate CBCT dose with reasonable accuracy in the clinical environment.« less

3D-Stereoscopic Analysis of Solar Active Region Loops. 2; SoHo/EIT Observations at Temperatures of 1.5-2.5 MK

NASA Technical Reports Server (NTRS)

Aschwanden, Markus J.; Alexander, David; Hurlburt, Neal; Newmark, Jeffrey S.; Neupert, Werner M.; Klimchuk, J. A.; Gary, G. Allen

1999-01-01

In this paper we study the three-dimensional (3D) structure of hot (T(sub e) approximately equals 1.5 - 2.5 MK) loops in solar active region NOAA 7986, observed on 1996 August 30 with the Extreme-ultraviolet Imaging Telescope (EIT) onboard the Solar and Heliospheric Observatory (SoHO). This complements a first study on cooler (T(sub e) approximately equals 1.0 - 1.5 MK) loops of the same active region, using the same method of Dynamic Stereoscopy to reconstruct the 3D geometry. We reconstruct the 3D-coordinates x(s), y(s), z(s), the density n(sub e)(s), and temperature profile T(sub e)(s) of 35 individual loop segments (as function of the loop coordinate s) using EIT 195 A and 284 A images. The major findings are: (1) All loops are found to be in hydrostatic equilibrium, in the entire temperature regime of T(sub e) = 1.0 - 2.5 MK; (2) The analyzed loops have a height of 2-3 scale heights, and thus only segments extending over about one vertical scale height have sufficient emission measure contrast for detection; (3) The temperature gradient over the lowest scale height is of order dT/ds is approximately 1 - 4 K/km; (4) The radiative loss rate is found to exceed the conductive loss rate by about two orders or magnitude, making thermal conduction negligible to explain the temperature structure of the loops; (5) A steady-state can only be achieved when the heating rate E(sub H) matches the radiative loss rate in hydrostatic equilibrium, requiring a heat deposition length lambda(sub H) of the half density scale height lambda, predicting a scaling law with the loop base pressure, EH varies as p(sub 0 exp 2). This favors coronal heating mechanisms that operate near the loop footpoints; (6) We find a reciprocal correlation between the loop pressure p(sub 0) and loop length L, i.e. p(sub 0) varies as 1/L, implying a scaling law of the steady-state requirement with loop length, i.e. E(sub H ) varies as 1/L(exp 2). The heating rate shows no correlation with the loop-aligned magnetic field component B(sub z) at the footpoints, but is correlated with the azimuthal field B(sub phi) = Bz(RDelta Phi/L) of a twisted loop, and is thus consistent with heating mechanisms based on field-aligned currents.

Short-term Time Step Convergence in a Climate Model

DOE PAGES

Wan, Hui; Rasch, Philip J.; Taylor, Mark; ...

2015-02-11

A testing procedure is designed to assess the convergence property of a global climate model with respect to time step size, based on evaluation of the root-mean-square temperature difference at the end of very short (1 h) simulations with time step sizes ranging from 1 s to 1800 s. A set of validation tests conducted without sub-grid scale parameterizations confirmed that the method was able to correctly assess the convergence rate of the dynamical core under various configurations. The testing procedure was then applied to the full model, and revealed a slow convergence of order 0.4 in contrast to themore » expected first-order convergence. Sensitivity experiments showed without ambiguity that the time stepping errors in the model were dominated by those from the stratiform cloud parameterizations, in particular the cloud microphysics. This provides a clear guidance for future work on the design of more accurate numerical methods for time stepping and process coupling in the model.« less

Ball Aerospace SBMD Coating Test Results

NASA Technical Reports Server (NTRS)

Brown, Robert; Lightsey, Paul; Russell, J. Kevin (Technical Monitor)

2002-01-01

The Sub-scale Beryllium Mirror Demonstrator that was successfully tested to demonstrate cryogenic figuring of a bare mirror has been coated with a protected gold reflective surface and retested at cryogenic temperatures. Results showing less than 9 nm rms surface distortion attributable to the added coating are presented.

Validating and improving CT ventilation imaging by correlating with ventilation 4D-PET/CT using {sup 68}Ga-labeled nanoparticles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kipritidis, John, E-mail: john.kipritidis@sydney.edu.au; Keall, Paul J.; Siva, Shankar

Purpose: CT ventilation imaging is a novel functional lung imaging modality based on deformable image registration. The authors present the first validation study of CT ventilation using positron emission tomography with{sup 68}Ga-labeled nanoparticles (PET-Galligas). The authors quantify this agreement for different CT ventilation metrics and PET reconstruction parameters. Methods: PET-Galligas ventilation scans were acquired for 12 lung cancer patients using a four-dimensional (4D) PET/CT scanner. CT ventilation images were then produced by applying B-spline deformable image registration between the respiratory correlated phases of the 4D-CT. The authors test four ventilation metrics, two existing and two modified. The two existing metricsmore » model mechanical ventilation (alveolar air-flow) based on Hounsfield unit (HU) change (V{sub HU}) or Jacobian determinant of deformation (V{sub Jac}). The two modified metrics incorporate a voxel-wise tissue-density scaling (ρV{sub HU} and ρV{sub Jac}) and were hypothesized to better model the physiological ventilation. In order to assess the impact of PET image quality, comparisons were performed using both standard and respiratory-gated PET images with the former exhibiting better signal. Different median filtering kernels (σ{sub m} = 0 or 3 mm) were also applied to all images. As in previous studies, similarity metrics included the Spearman correlation coefficient r within the segmented lung volumes, and Dice coefficient d{sub 20} for the (0 − 20)th functional percentile volumes. Results: The best agreement between CT and PET ventilation was obtained comparing standard PET images to the density-scaled HU metric (ρV{sub HU}) with σ{sub m} = 3 mm. This leads to correlation values in the ranges 0.22 ⩽ r ⩽ 0.76 and 0.38 ⩽ d{sub 20} ⩽ 0.68, with r{sup ¯}=0.42±0.16 and d{sup ¯}{sub 20}=0.52±0.09 averaged over the 12 patients. Compared to Jacobian-based metrics, HU-based metrics lead to statistically significant improvements in r{sup ¯} and d{sup ¯}{sub 20} (p < 0.05), with density scaled metrics also showing higher r{sup ¯} than for unscaled versions (p < 0.02). r{sup ¯} and d{sup ¯}{sub 20} were also sensitive to image quality, with statistically significant improvements using standard (as opposed to gated) PET images and with application of median filtering. Conclusions: The use of modified CT ventilation metrics, in conjunction with PET-Galligas and careful application of image filtering has resulted in improved correlation compared to earlier studies using nuclear medicine ventilation. However, CT ventilation and PET-Galligas do not always provide the same functional information. The authors have demonstrated that the agreement can improve for CT ventilation metrics incorporating a tissue density scaling, and also with increasing PET image quality. CT ventilation imaging has clear potential for imaging regional air volume change in the lung, and further development is warranted.« less

Traditional and innovative methods applied to a crystalline aquifer for characterizing fault zone hydrology at different scales

NASA Astrophysics Data System (ADS)

Bour, O.; Ruelleu, S.; Le Borgne, T.; Boudin, F.; Moreau, F.; Durand, S.; Longuevergne, L.

2011-12-01

Crystalline rocks aquifers are difficult to characterize since flow is mainly localized in few fractures or faults. In particular, the geometry of the main flow paths and the connections of the aquifer with the sub-surface are often poorly constrained. Here, we present results from different geophysical and hydraulic methods to quantify fault zone hydrology of a crystalline confined aquifer (Ploemeur, French Brittany). This outstandingly productive crystalline rock aquifer is exploited at a rate of about 10 6 m3 per year since 1991. The pumping site is located at the intersection of two main structures: the contact zone between granite roof and overlying micaschists, and a steeply dipping fault striking North 20°, with combined dextral strike-slip and normal components. Core samples and borehole optical imagery reveals that the contact zone at the granite roof consists of alternating deformed granitic sheets and enclaves of micaschists, pegmatite and aplite dykes, as well as quartz veins. Locally, this contact is marked by mylonites and pegmatite-bearing breccias that are often but not systematically associated with major borehole inflows. Other significant inflows are localized within single fractures independently of the lithologies encountered. At the borehole scale the structural and hydraulic properties of the aquifer are thus highly variable. At the site scale - typically a kilometer squared - the water levels are monitored in 22 boreholes, 100 meters deep in average. The connectivity of the main flow paths and the hydraulic properties are relatively well constrained and quantified thanks to cross-borehole flowmeter tests and traditional pumping tests. In complement, long-base tiltmeters monitoring and ground-surface leveling allows to monitor sub-surface deformation. It provides a quantification of the hydro-mechanical properties of the aquifer and better constraints about the geometry of the main fault zone. Surprisingly, the storage coefficient of the confined aquifer is relatively high, in agreement with ground-surface deformation measurements that suggest a relativity high compressibility of the fault zone. At larger scale, we show through a high-resolution gravimetric survey that the highly fractured contact between granite and micaschists, which constitutes the main path for groundwater flow, is a gently dipping structure. A 3D gravimetric model confirms also the presence of sub-vertical faults that may constitute important drains for the aquifer recharge. In addition, groundwater temperature monitoring allows to shows that the main water supply comes from a depth of at least 300 meters. Such a depth in a low relief region involves relatively deep groundwater circulation that can be achieved only thanks to major permeable fault zone. This field example shows the advantages and limitations of some traditional and innovative methods to characterize fault zone hydrology in crystalline bedrock aquifers.

Improved accuracy in quantitative laser-induced breakdown spectroscopy using sub-models

USGS Publications Warehouse

Anderson, Ryan; Clegg, Samuel M.; Frydenvang, Jens; Wiens, Roger C.; McLennan, Scott M.; Morris, Richard V.; Ehlmann, Bethany L.; Dyar, M. Darby

2017-01-01

Accurate quantitative analysis of diverse geologic materials is one of the primary challenges faced by the Laser-Induced Breakdown Spectroscopy (LIBS)-based ChemCam instrument on the Mars Science Laboratory (MSL) rover. The SuperCam instrument on the Mars 2020 rover, as well as other LIBS instruments developed for geochemical analysis on Earth or other planets, will face the same challenge. Consequently, part of the ChemCam science team has focused on the development of improved multivariate analysis calibrations methods. Developing a single regression model capable of accurately determining the composition of very different target materials is difficult because the response of an element’s emission lines in LIBS spectra can vary with the concentration of other elements. We demonstrate a conceptually simple “sub-model” method for improving the accuracy of quantitative LIBS analysis of diverse target materials. The method is based on training several regression models on sets of targets with limited composition ranges and then “blending” these “sub-models” into a single final result. Tests of the sub-model method show improvement in test set root mean squared error of prediction (RMSEP) for almost all cases. The sub-model method, using partial least squares regression (PLS), is being used as part of the current ChemCam quantitative calibration, but the sub-model method is applicable to any multivariate regression method and may yield similar improvements.

Predictive Model for Particle Residence Time Distributions in Riser Reactors. Part 1: Model Development and Validation

DOE PAGES

Foust, Thomas D.; Ziegler, Jack L.; Pannala, Sreekanth; ...

2017-02-28

Here in this computational study, we model the mixing of biomass pyrolysis vapor with solid catalyst in circulating riser reactors with a focus on the determination of solid catalyst residence time distributions (RTDs). A comprehensive set of 2D and 3D simulations were conducted for a pilot-scale riser using the Eulerian-Eulerian two-fluid modeling framework with and without sub-grid-scale models for the gas-solids interaction. A validation test case was also simulated and compared to experiments, showing agreement in the pressure gradient and RTD mean and spread. For simulation cases, it was found that for accurate RTD prediction, the Johnson and Jackson partialmore » slip solids boundary condition was required for all models and a sub-grid model is useful so that ultra high resolutions grids that are very computationally intensive are not required. Finally, we discovered a 2/3 scaling relation for the RTD mean and spread when comparing resolved 2D simulations to validated unresolved 3D sub-grid-scale model simulations.« less

Development of Subscale Fast Cookoff Test (PREPRINT)

DTIC Science & Technology

2006-09-21

The hazards classification procedures have been harmonized with both the UN Test and Criteria Manual for UN Series 1...aimed at the development of a sub-scale alternate test protocol to the external fire test currently required for final hazards classification (HC...external fire test currently required for final hazards classification (HC) of an ordnance system. The specific goal of this part of the task was

A multiscale method for modeling high-aspect-ratio micro/nano flows

NASA Astrophysics Data System (ADS)

Lockerby, Duncan; Borg, Matthew; Reese, Jason

2012-11-01

In this paper we present a new multiscale scheme for simulating micro/nano flows of high aspect ratio in the flow direction, e.g. within long ducts, tubes, or channels, of varying section. The scheme consists of applying a simple hydrodynamic description over the entire domain, and allocating micro sub-domains in very small ``slices'' of the channel. Every micro element is a molecular dynamics simulation (or other appropriate model, e.g., a direct simulation Monte Carlo method for micro-channel gas flows) over the local height of the channel/tube. The number of micro elements as well as their streamwise position is chosen to resolve the geometrical features of the macro channel. While there is no direct communication between individual micro elements, coupling occurs via an iterative imposition of mass and momentum-flux conservation on the macro scale. The greater the streamwise scale of the geometry, the more significant is the computational speed-up when compared to a full MD simulation. We test our new multiscale method on the case of a converging/diverging nanochannel conveying a simple Lennard-Jones liquid. We validate the results from our simulations by comparing them to a full MD simulation of the same test case. Supported by EPSRC Programme Grant, EP/I011927/1.

System Level Aerothermal Testing for the Adaptive Deployable Entry and Placement Technology (ADEPT)

NASA Technical Reports Server (NTRS)

Cassell, Alan; Gorbunov, Sergey; Yount, Bryan; Prabhu, Dinesh; de Jong, Maxim; Boghozian, Tane; Hui, Frank; Chen, Y.-K.; Kruger, Carl; Poteet, Carl;

Test of phi(sup 2) model predictions near the (sup 3)He liquid-gas critical point

NASA Technical Reports Server (NTRS)

Barmatz, M.; Zhong, F.; Hahn, I.

2000-01-01

NASA is supporting the development of an experiment called MISTE (Microgravity Scaling Theory Experiment) for future International Space Station mission. The main objective of this flight experiment is to perform in-situ PVT, heat capacity at constant volume, C(sub v) and chi(sub tau), measurements in the asymptotic region near the (sup 3)He liquid-gas critical point.

An Experimental Study of Airfoil Icing Characteristics

NASA Technical Reports Server (NTRS)

Shaw, R. J.; Sotos, R. G.; Solano, F. R.

1982-01-01

A full scale general aviation wing with a NACA 63 sub 2 A415 airfoil section was tested to determine icing characteristics for representative rime and glaze icing conditions. Measurements were made of ice accretion shapes and resultant wing section drag coefficient levels. It was found that the NACA 63 sub 2 A415 wing section was less sensitive to rime and glaze icing encounters for climb conditions.

JV Task 124 - Understanding Multi-Interactions of SO3, Mercury, Selenium, and Arsenic in Illinois Coal Flue Gas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ye Zhuang; Christopher Martin; John Pavlish

2009-03-31

This project consisted of pilot-scale combustion testing with a representative Illinois basin coal to explore the multi-interactions of SO{sub 3}, mercury, selenium and arsenic. The parameters investigated for SO{sub 3} and mercury interactions included different flue gas conditions, i.e., temperature, moisture content, and particulate alkali content, both with and without activated carbon injection for mercury control. Measurements were also made to track the transformation of selenium and arsenic partitioning as a function of flue gas temperature through the system. The results from the mercury-SO{sub 3} testing support the concept that SO{sub 3} vapor is the predominant factor that impedes efficientmore » mercury removal with activated carbon in an Illinois coal flue gas, while H{sub 2}SO{sub 4} aerosol has less impact on activated carbon injection performance. Injection of a suitably mobile and reactive additives such as sodium- or calcium-based sorbents was the most effective strategy tested to mitigate the effect of SO{sub 3}. Transformation measurements indicate a significant fraction of selenium was associated with the vapor phase at the electrostatic precipitator inlet temperature. Arsenic was primarily particulate-bound and should be captured effectively with existing particulate control technology.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Sangkyu; Park, Hun; Paik, Ungyu

We have discovered a methodology to realize the fabrication of flexible metal oxide film using two-dimensional (2D) nanosheets. Atomic scale titanium oxide (TiO{sub x}) nanosheets were exfoliated from bulk TiO{sub x} powder that had a layered structure via the modified Sasaki’s method. The vacuum-assisted filtration generates films with laterally aligned TiO{sub x} nanosheets. The 2D sheet-like structure and hydrophilic nature of TiO{sub x} nanosheets enables the film consisting of TiO{sub x} nanosheets to be bendable. Also, we demonstrate the fabrication of electrochemical capacitors using this film. The mechanically flexible metal oxide film is expected to open up the possibility ofmore » fabricating flexible energy storage devices from 2D metal oxide nanosheets. - Graphical abstract: The modified Sasaki’s method, combined process of hydrothermal reaction and bulky ion exchange, enables to obtain TiO{sub x} monolayer nanosheets. The vacuum-assisted filtration generates bendable films with laterally aligned TiO{sub x} nanosheets. Also, we demonstrate the fabrication of electrochemical capacitors using this film. - Highlights: • TiO{sub x} single sheets, a novel 2-dimensional material, were exfoliated from bulk powders via the modified Sasaki’s method. • In our method, the acid treatment of TiO{sub x} bulk powders was simply modified by applying the hydrothermal reaction. • Then, the delamination procedures of large cation exchange were conducted following the method proposed by Sasaki et al. • Reassembly of TiO{sub x} sheets into flexible free-standing films was simply achieved via vacuum assisted filtration method. • TiO{sub x} films were used as a flexible supercapaictor electrode material.« less

Oxidation behavior of V-Cr-Ti alloys in low-partial-pressure oxygen environments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Natesan, K.; Uz, M.

A test program is in progress at Argonne National Laboratory to evaluate the effect of pO{sub 2} in the exposure environment on oxygen uptake, scaling kinetics, and scale microstructure in V-Cr-Ti alloys. The data indicate that the oxidation process follows parabolic kinetics in all of the environments used in the present study. From the weight change data, parabolic rate constants were evaluated as a function of temperature and exposure environment. The temperature dependence of the parabolic rate constants was described by an Arrhenius relationship. Activation energy for the oxidation process was fairly constant in the oxygen pressure range of 1more » {times} 10{sup {minus}6} to 1 {times} 10{sup {minus}1} torr for both the alloys. The activation energy for oxidation in air was significantly lower than in low-pO{sub 2} environments, and for oxidation in pure O{sub 2} at 760 torr was much lower than in low-pO{sub 2} environments. X-ray diffraction analysis of the specimens showed that VO{sub 2} was the dominant phase in low-pO{sub 2} environments, while V{sub 2}O{sub 5} was dominant in air and in pure oxygen at 76f0 torr.« less

With a small stabilization parachute trailing behind, the X-40 sub-scale technology demonstrator is suspended under a U.S. Army CH-47 Chinook cargo helicopter during a captive-carry test flight

NASA Image and Video Library

2000-12-08

With a small stabilization parachute trailing behind, the X-40 sub-scale technology demonstrator is suspended under a U.S. Army CH-47 Chinook cargo helicopter during a captive-carry test flight at NASA's Dryden Flight Research Center, Edwards, California. The captive carry flights are designed to verify the X-40's navigation and control systems, rigging angles for its sling, and stability and control of the helicopter while carrying the X-40 on a tether. Following a series of captive-carry flights, the X-40 made free flights from a launch altitude of about 15,000 feet above ground, gliding to a fully autonomous landing. The X-40 is an unpowered 82 percent scale version of the X-37, a Boeing-developed spaceplane designed to demonstrate various advanced technologies for development of future lower-cost access to space vehicles.

FUEL-FLEXIBLE GASIFICATION-COMBUSTION TECHNOLOGY FOR PRODUCTION OF H2 AND SEQUESTRATION-READY CO2

DOE Office of Scientific and Technical Information (OSTI.GOV)

George Rizeq; Janice West; Arnaldo Frydman

It is expected that in the 21st century the Nation will continue to rely on fossil fuels for electricity, transportation, and chemicals. It will be necessary to improve both the process efficiency and environmental impact performance of fossil fuel utilization. GE Global Research has developed an innovative fuel-flexible Unmixed Fuel Processor (UFP) technology to produce H{sub 2}, power, and sequestration-ready CO{sub 2} from coal and other solid fuels. The UFP module offers the potential for reduced cost, increased process efficiency relative to conventional gasification and combustion systems, and near-zero pollutant emissions including NO{sub x}. GE Global Research (prime contractor) wasmore » awarded a contract from U.S. DOE NETL to develop the UFP technology. Work on this Phase I program started on October 1, 2000. The project team includes GE Global Research, Southern Illinois University at Carbondale (SIU-C), California Energy Commission (CEC), and T. R. Miles, Technical Consultants, Inc. In the UFP technology, coal and air are simultaneously converted into separate streams of (1) high-purity hydrogen that can be utilized in fuel cells or turbines, (2) sequestration-ready CO{sub 2}, and (3) high temperature/pressure vitiated air to produce electricity in a gas turbine. The process produces near-zero emissions and, based on ASPEN Plus process modeling, has an estimated process efficiency of 6 percentage points higher than IGCC with conventional CO{sub 2} separation. The current R&D program will determine the feasibility of the integrated UFP technology through pilot-scale testing, and will investigate operating conditions that maximize separation of CO{sub 2} and pollutants from the vent gas, while simultaneously maximizing coal conversion efficiency and hydrogen production. The program integrates experimental testing, modeling and economic studies to demonstrate the UFP technology. This is the fourteenth quarterly technical progress report for the UFP program, which is supported by U.S. DOE NETL (Contract No. DE-FC26-00FT40974) and GE. This report summarizes program accomplishments for the period starting January 1, 2004 and ending March 31, 2004. The report includes an introduction summarizing the UFP technology, main program tasks, and program objectives; it also provides a summary of program activities and accomplishments covering progress in tasks including lab-scale experimental testing, pilot-scale shakedown and performance testing, program management and technology transfer.« less

FUEL-FLEXIBLE GASIFICATION-COMBUSTION TECHNOLOGY FOR PRODUCTION OF H2 AND SEQUESTRATION-READY CO2

DOE Office of Scientific and Technical Information (OSTI.GOV)

George Rizeq; Janice West; Arnaldo Frydman

It is expected that in the 21st century the Nation will continue to rely on fossil fuels for electricity, transportation, and chemicals. It will be necessary to improve both the process efficiency and environmental impact performance of fossil fuel utilization. GE Global Research has developed an innovative fuel-flexible Unmixed Fuel Processor (UFP) technology to produce H{sub 2}, power, and sequestration-ready CO{sub 2} from coal and other solid fuels. The UFP module offers the potential for reduced cost, increased process efficiency relative to conventional gasification and combustion systems, and near-zero pollutant emissions including NO{sub x}. GE Global Research (prime contractor) wasmore » awarded a contract from U.S. DOE NETL to develop the UFP technology. Work on this Phase I program started on October 1, 2000. The project team includes GE Global Research, Southern Illinois University at Carbondale (SIU-C), California Energy Commission (CEC), and T. R. Miles, Technical Consultants, Inc. In the UFP technology, coal and air are simultaneously converted into separate streams of (1) high-purity hydrogen that can be utilized in fuel cells or turbines, (2) sequestration-ready CO{sub 2}, and (3) high temperature/pressure vitiated air to produce electricity in a gas turbine. The process produces near-zero emissions and, based on ASPEN Plus process modeling, has an estimated process efficiency of 6 percentage points higher than IGCC with conventional CO{sub 2} separation. The current R&D program has determined the feasibility of the integrated UFP technology through pilot-scale testing, and investigated operating conditions that maximize separation of CO{sub 2} and pollutants from the vent gas, while simultaneously maximizing coal conversion efficiency and hydrogen production. The program integrated experimental testing, modeling and economic studies to demonstrate the UFP technology. This is the fifteenth quarterly technical progress report for the UFP program, which is supported by U.S. DOE NETL (Contract No. DE-FC26-00FT40974) and GE. This report summarizes program accomplishments for the period starting April 1, 2004 and ending June 30, 2004. The report includes an introduction summarizing the UFP technology, main program tasks, and program objectives; it also provides a summary of program activities and accomplishments covering progress in tasks including lab-scale experimental testing, pilot-scale testing, kinetic modeling, program management and technology transfer.« less

Mercury emissions during cofiring of sub-bituminous coal and biomass (chicken waste, wood, coffee residue, and tobacco stalk) in a laboratory-scale fluidized bed combustor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yan Cao; Hongcang Zhou; Junjie Fan

Four types of biomass (chicken waste, wood pellets, coffee residue, and tobacco stalks) were cofired at 30 wt % with a U.S. sub-bituminous coal (Powder River Basin Coal) in a laboratory-scale fluidized bed combustor. A cyclone, followed by a quartz filter, was used for fly ash removal during tests. The temperatures of the cyclone and filter were controlled at 250 and 150{sup o}C, respectively. Mercury speciation and emissions during cofiring were investigated using a semicontinuous mercury monitor, which was certified using ASTM standard Ontario Hydra Method. Test results indicated mercury emissions were strongly correlative to the gaseous chlorine concentrations, butmore » not necessarily correlative to the chlorine contents in cofiring fuels. Mercury emissions could be reduced by 35% during firing of sub-bituminous coal using only a quartz filter. Cofiring high-chlorine fuel, such as chicken waste (Cl = 22340 wppm), could largely reduce mercury emissions by over 80%. When low-chlorine biomass, such as wood pellets (Cl = 132 wppm) and coffee residue (Cl = 134 wppm), is cofired, mercury emissions could only be reduced by about 50%. Cofiring tobacco stalks with higher chlorine content (Cl = 4237 wppm) did not significantly reduce mercury emissions. Gaseous speciated mercury in flue gas after a quartz filter indicated the occurrence of about 50% of total gaseous mercury to be the elemental mercury for cofiring chicken waste, but occurrence of above 90% of the elemental mercury for all other cases. Both the higher content of alkali metal oxides or alkali earth metal oxides in tested biomass and the occurrence of temperatures lower than 650{sup o}C in the upper part of the fluidized bed combustor seemed to be responsible for the reduction of gaseous chlorine and, consequently, limited mercury emissions reduction during cofiring. 36 refs., 3 figs. 1 tab.« less

Recent Dynamic Measurements and Considerations for Aerodynamic Modeling of Fighter Airplane Configurations

NASA Technical Reports Server (NTRS)

Brandon, Jay M.; Foster, John V.

1998-01-01

As airplane designs have trended toward the expansion of flight envelopes into the high angle of attack and high angular rate regimes, concerns regarding modeling the complex unsteady aerodynamics for simulation have arisen. Most current modeling methods still rely on traditional body axis damping coefficients that are measured using techniques which were intended for relatively benign flight conditions. This paper presents recent wind tunnel results obtained during large-amplitude pitch, roll and yaw testing of several fighter airplane configurations. A review of the similitude requirements for applying sub-scale test results to full-scale conditions is presented. Data is then shown to be a strong function of Strouhal number - both the traditional damping terms, but also the associated static stability terms. Additionally, large effects of sideslip are seen in the damping parameter that should be included in simulation math models. Finally, an example of the inclusion of frequency effects on the data in a simulation is shown.

Probing the A1 to L1{sub 0} transformation in FeCuPt using the first order reversal curve method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gilbert, Dustin A.; Liu, Kai; Liao, Jung-Wei

2014-08-01

The A1-L1{sub 0} phase transformation has been investigated in (001) FeCuPt thin films prepared by atomic-scale multilayer sputtering and rapid thermal annealing (RTA). Traditional x-ray diffraction is not always applicable in generating a true order parameter, due to non-ideal crystallinity of the A1 phase. Using the first-order reversal curve (FORC) method, the A1 and L1{sub 0} phases are deconvoluted into two distinct features in the FORC distribution, whose relative intensities change with the RTA temperature. The L1{sub 0} ordering takes place via a nucleation-and-growth mode. A magnetization-based phase fraction is extracted, providing a quantitative measure of the L1{sub 0} phasemore » homogeneity.« less

Edge detection based on adaptive threshold b-spline wavelet for optical sub-aperture measuring

NASA Astrophysics Data System (ADS)

Zhang, Shiqi; Hui, Mei; Liu, Ming; Zhao, Zhu; Dong, Liquan; Liu, Xiaohua; Zhao, Yuejin

2015-08-01

In the research of optical synthetic aperture imaging system, phase congruency is the main problem and it is necessary to detect sub-aperture phase. The edge of the sub-aperture system is more complex than that in the traditional optical imaging system. And with the existence of steep slope for large-aperture optical component, interference fringe may be quite dense when interference imaging. Deep phase gradient may cause a loss of phase information. Therefore, it's urgent to search for an efficient edge detection method. Wavelet analysis as a powerful tool is widely used in the fields of image processing. Based on its properties of multi-scale transform, edge region is detected with high precision in small scale. Longing with the increase of scale, noise is reduced in contrary. So it has a certain suppression effect on noise. Otherwise, adaptive threshold method which sets different thresholds in various regions can detect edge points from noise. Firstly, fringe pattern is obtained and cubic b-spline wavelet is adopted as the smoothing function. After the multi-scale wavelet decomposition of the whole image, we figure out the local modulus maxima in gradient directions. However, it also contains noise, and thus adaptive threshold method is used to select the modulus maxima. The point which greater than threshold value is boundary point. Finally, we use corrosion and expansion deal with the resulting image to get the consecutive boundary of image.

Very-high-Reynolds-number vortex dynamics via Coherent-vorticity-Preserving (CvP) Large-eddy simulations

NASA Astrophysics Data System (ADS)

Chapelier, Jean-Baptiste; Wasistho, Bono; Scalo, Carlo

2017-11-01

A new approach to Large-Eddy Simulation (LES) is introduced, where subgrid-scale (SGS) dissipation is applied proportionally to the degree of local spectral broadening, hence mitigated in regions dominated by large-scale vortical motion. The proposed CvP-LES methodology is based on the evaluation of the ratio of the test-filtered to resolved (or grid-filtered) enstrophy: σ = ξ ∧ / ξ . Values of σ = 1 indicate low sub-test-filter turbulent activity, justifying local deactivation of any subgrid-scale model. Values of σ < 1 span conditions ranging from incipient spectral broadening σ <= 1 , to equilibrium turbulence σ =σeq < 1 , where σeq is solely as a function of the test-to-grid filter-width ratio Δ ∧ / Δ , derived assuming a Kolmogorov's spectrum. Eddy viscosity is fully restored for σ <=σeq . The proposed approach removes unnecessary SGS dissipation, can be applied to any eddy-viscosity model, is algorithmically simple and computationally inexpensive. A CvP-LES of a pair of unstable helical vortices, representative of rotor-blade wake dynamics, show the ability of the method to sort the coherent motion from the small-scale dynamics. This work is funded by subcontract KSC-17-001 between Purdue University and Kord Technologies, Inc (Huntsville), under the US Navy Contract N68335-17-C-0159 STTR-Phase II, Purdue Proposal No. 00065007, Topic N15A-T002.

Utilizing the ultrasensitive Schistosoma up-converting phosphor lateral flow circulating anodic antigen (UCP-LF CAA) assay for sample pooling-strategies.

PubMed

Corstjens, Paul L A M; Hoekstra, Pytsje T; de Dood, Claudia J; van Dam, Govert J

2017-11-01

Methodological applications of the high sensitivity genus-specific Schistosoma CAA strip test, allowing detection of single worm active infections (ultimate sensitivity), are discussed for efficient utilization in sample pooling strategies. Besides relevant cost reduction, pooling of samples rather than individual testing can provide valuable data for large scale mapping, surveillance, and monitoring. The laboratory-based CAA strip test utilizes luminescent quantitative up-converting phosphor (UCP) reporter particles and a rapid user-friendly lateral flow (LF) assay format. The test includes a sample preparation step that permits virtually unlimited sample concentration with urine, reaching ultimate sensitivity (single worm detection) at 100% specificity. This facilitates testing large urine pools from many individuals with minimal loss of sensitivity and specificity. The test determines the average CAA level of the individuals in the pool thus indicating overall worm burden and prevalence. When requiring test results at the individual level, smaller pools need to be analysed with the pool-size based on expected prevalence or when unknown, on the average CAA level of a larger group; CAA negative pools do not require individual test results and thus reduce the number of tests. Straightforward pooling strategies indicate that at sub-population level the CAA strip test is an efficient assay for general mapping, identification of hotspots, determination of stratified infection levels, and accurate monitoring of mass drug administrations (MDA). At the individual level, the number of tests can be reduced i.e. in low endemic settings as the pool size can be increased as opposed to prevalence decrease. At the sub-population level, average CAA concentrations determined in urine pools can be an appropriate measure indicating worm burden. Pooling strategies allowing this type of large scale testing are feasible with the various CAA strip test formats and do not affect sensitivity and specificity. It allows cost efficient stratified testing and monitoring of worm burden at the sub-population level, ideally for large-scale surveillance generating hard data for performance of MDA programs and strategic planning when moving towards transmission-stop and elimination.

Low energy theorems and the unitarity bounds in the extra U(1) superstring inspired E{sub 6} models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sharma, N.K.; Saxena, Pranav; Nagawat, Ashok K.

2005-11-01

The conventional method using low energy theorems derived by Chanowitz et al. [Phys. Rev. Lett. 57, 2344 (1986);] does not seem to lead to an explicit unitarity limit in the scattering processes of longitudinally polarized gauge bosons for the high energy case in the extra U(1) superstring inspired models, commonly known as {eta} model, emanating from E{sub 6} group of superstring theory. We have made use of an alternative procedure given by Durand and Lopez [Phys. Lett. B 217, 463 (1989);], which is applicable to supersymmetric grand unified theories. Explicit unitarity bounds on the superpotential couplings (identified as Yukawa couplings)more » are obtained from both using unitarity constraints as well as using renormalization group equations (RGE) analysis at one-loop level utilizing critical couplings concepts implying divergence of scalar coupling at M{sub G}. These are found to be consistent with finiteness over the entire range M{sub Z}{<=}{radical}(s){<=}M{sub G} i.e. from grand unification scale to weak scale. For completeness, the similar approach has been made use of in other models i.e., {chi}, {psi}, and {nu} models emanating from E{sub 6} and it has been noticed that at weak scale, the unitarity bounds on Yukawa couplings do not differ among E{sub 6} extra U(1) models significantly except for the case of {chi} model in 16 representations. For the case of the E{sub 6}-{eta} model ({beta}{sub E} congruent with 9.64), the analysis using the unitarity constraints leads to the following bounds on various parameters: {lambda}{sub t(max.)}(M{sub Z})=1.294, {lambda}{sub b(max.)}(M{sub Z})=1.278, {lambda}{sub H(max.)}(M{sub Z})=0.955, {lambda}{sub D(max.)}(M{sub Z})=1.312. The analytical analysis of RGE at the one-loop level provides the following critical bounds on superpotential couplings: {lambda}{sub t,c}(M{sub Z}) congruent with 1.295, {lambda}{sub b,c}(M{sub Z}) congruent with 1.279, {lambda}{sub H,c}(M{sub Z}) congruent with 0.968, {lambda}{sub D,c}(M{sub Z}) congruent with 1.315. Thus superpotential coupling values obtained by both the approaches are in good agreement. Theoretically we have obtained bounds on physical mass parameters using the unitarity constrained superpotential couplings. The bounds are as follows: (i) Absolute upper bound on top quark mass m{sub t}{<=}225 GeV (ii) the upper bound on the lightest neutral Higgs boson mass at the tree level is m{sub H{sub 2}{sup 0}}{sup tree}{<=}169 GeV, and after the inclusion of the one-loop radiative correction it is m{sub H{sub 2}{sup 0}}{<=}229 GeV when {lambda}{sub t}{ne}{lambda}{sub b} at the grand unified theory scale. On the other hand, these are m{sub H{sub 2}{sup 0}}{sup tree}{<=}159 GeV, m{sub H{sub 2}{sup 0}}{<=}222 GeV, respectively, when {lambda}{sub t}={lambda}{sub b} at the grand unified theory scale. A plausible range on D-quark mass as a function of mass scale M{sub Z{sub 2}} is m{sub D}{approx_equal}O(3 TeV) for M{sub Z{sub 2}}{approx_equal}O(1 TeV) for the favored values of tan{beta}{<=}1. The bounds on aforesaid physical parameters in the case of {chi}, {psi}, and {nu} models in the 27 representation are almost identical with those of {eta} model and are consistent with the present day experimental precision measurements.« less

Product Reliability Trends, Derating Considerations and Failure Mechanisms with Scaled CMOS

NASA Technical Reports Server (NTRS)

White, Mark; Vu, Duc; Nguyen, Duc; Ruiz, Ron; Chen, Yuan; Bernstein, Joseph B.

2006-01-01

As microelectronics is scaled into the deep sub-micron regime, space and aerospace users of advanced technology CMOS are reassessing how scaling effects impact long-term product reliability. The effects of electromigration (EM), time-dependent-dielectric-breakdown (TDDB) and hot carrier degradation (HCI and NBTI) wearout mechanisms on scaled technologies and product reliability are investigated, accelerated stress testing across several technology nodes is performed, and FA is conducted to confirm the failure mechanism(s).

External validity of a generic safety climate scale for lone workers across different industries and companies.

PubMed

Lee, Jin; Huang, Yueng-hsiang; Robertson, Michelle M; Murphy, Lauren A; Garabet, Angela; Chang, Wen-Ruey

2014-02-01

The goal of this study was to examine the external validity of a 12-item generic safety climate scale for lone workers in order to evaluate the appropriateness of generalized use of the scale in the measurement of safety climate across various lone work settings. External validity evidence was established by investigating the measurement equivalence (ME) across different industries and companies. Confirmatory factor analysis (CFA)-based and item response theory (IRT)-based perspectives were adopted to examine the ME of the generic safety climate scale for lone workers across 11 companies from the trucking, electrical utility, and cable television industries. Fairly strong evidence of ME was observed for both organization- and group-level generic safety climate sub-scales. Although significant invariance was observed in the item intercepts across the different lone work settings, absolute model fit indices remained satisfactory in the most robust step of CFA-based ME testing. IRT-based ME testing identified only one differentially functioning item from the organization-level generic safety climate sub-scale, but its impact was minimal and strong ME was supported. The generic safety climate scale for lone workers reported good external validity and supported the presence of a common feature of safety climate among lone workers. The scale can be used as an effective safety evaluation tool in various lone work situations. Copyright © 2013 Elsevier Ltd. All rights reserved.

Design of the 15 GHz BPM test bench for the CLIC test facility to perform precise stretched-wire RF measurements

NASA Astrophysics Data System (ADS)

Zorzetti, Silvia; Fanucci, Luca; Galindo Muñoz, Natalia; Wendt, Manfred

2015-09-01

The Compact Linear Collider (CLIC) requires a low emittance beam transport and preservation, thus a precise control of the beam orbit along up to 50 km of the accelerator components in the sub-μm regime is required. Within the PACMAN3 (Particle Accelerator Components Metrology and Alignment to the Nanometer Scale) PhD training action a study with the objective of pre-aligning the electrical centre of a 15 GHz cavity beam position monitor (BPM) to the magnetic centre of the main beam quadrupole is initiated. Of particular importance is the design of a specific test bench to study the stretched-wire setup for the CLIC Test Facility (CTF3) BPM, focusing on the aspects of microwave signal excitation, transmission and impedance-matching, as well as the mechanical setup and reproducibility of the measurement method.

Permutation invariant potential energy surfaces for polyatomic reactions using atomistic neural networks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kolb, Brian; Department of Mechanical Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139; Zhao, Bin

2016-06-14

The applicability and accuracy of the Behler-Parrinello atomistic neural network method for fitting reactive potential energy surfaces is critically examined in three systems, H + H{sub 2} → H{sub 2} + H, H + H{sub 2}O → H{sub 2} + OH, and H + CH{sub 4} → H{sub 2} + CH{sub 3}. A pragmatic Monte Carlo method is proposed to make efficient choice of the atom-centered mapping functions. The accuracy of the potential energy surfaces is not only tested by fitting errors but also validated by direct comparison in dynamically important regions and by quantum scattering calculations. Our results suggestmore » this method is both accurate and efficient in representing multidimensional potential energy surfaces even when dissociation continua are involved.« less

Integrated dry NO{sub x}/SO{sub 2} emissions control system performance summary

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hunt, T.; Muzio, L.J.; Smith, R.

1997-12-31

The Integrated Dry NO{sub x}/SO{sub 2} Emissions Control System was installed at Public Service Company of Colorado`s Arapahoe 4 generating station in 1992 in cooperation with the US Department of Energy (DOE) and the Electric Power Research Institute (EPRI). This full-scale 100 MWe demonstration combines low-NO{sub x} burners, overfire, air, and selective non-catalytic reduction (SNCR) for NO{sub x} control and dry sorbent injection (DSI) with or without humidification for SO{sub 2} control. Operation and testing of the Integrated Dry NO{sub x}/SO{sub 2} Emissions Control System began in August 1992 and will continue through 1996. Results of the NO{sub x} controlmore » technologies show that the original system goal of 70% NO{sub x} removal has been easily met and the combustion and SNCR systems can achieve NO{sub x} removals of up to 80% at full load. Duct injection of commercial calcium hydroxide has achieved a maximum SO{sub 2} removal of nearly 40% while humidifying the flue gas to a 20 F approach to saturation. Sodium-based dry sorbent injection has provided SO{sub 2} removal of over 70% without the occurrence of a visible NO{sub 2} plume. Recent test work has improved SNCR performance at low loads and has demonstrated that combined dry sodium injection and SNCR yields both lower NO{sub 2} levels and NH{sub 3} slip than either technology alone.« less

Sub-pixel flood inundation mapping from multispectral remotely sensed images based on discrete particle swarm optimization

NASA Astrophysics Data System (ADS)

Li, Linyi; Chen, Yun; Yu, Xin; Liu, Rui; Huang, Chang

2015-03-01

The study of flood inundation is significant to human life and social economy. Remote sensing technology has provided an effective way to study the spatial and temporal characteristics of inundation. Remotely sensed images with high temporal resolutions are widely used in mapping inundation. However, mixed pixels do exist due to their relatively low spatial resolutions. One of the most popular approaches to resolve this issue is sub-pixel mapping. In this paper, a novel discrete particle swarm optimization (DPSO) based sub-pixel flood inundation mapping (DPSO-SFIM) method is proposed to achieve an improved accuracy in mapping inundation at a sub-pixel scale. The evaluation criterion for sub-pixel inundation mapping is formulated. The DPSO-SFIM algorithm is developed, including particle discrete encoding, fitness function designing and swarm search strategy. The accuracy of DPSO-SFIM in mapping inundation at a sub-pixel scale was evaluated using Landsat ETM + images from study areas in Australia and China. The results show that DPSO-SFIM consistently outperformed the four traditional SFIM methods in these study areas. A sensitivity analysis of DPSO-SFIM was also carried out to evaluate its performances. It is hoped that the results of this study will enhance the application of medium-low spatial resolution images in inundation detection and mapping, and thereby support the ecological and environmental studies of river basins.

Production of Hydrogen by Superadiabatic Decomposition of Hydrogen Sulfide - Final Technical Report for the Period June 1, 1999 - September 30, 2000

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rachid B. Slimane; Francis S. Lau; Javad Abbasian

2000-10-01

The objective of this program is to develop an economical process for hydrogen production, with no additional carbon dioxide emission, through the thermal decomposition of hydrogen sulfide (H{sub 2}S) in H{sub 2}S-rich waste streams to high-purity hydrogen and elemental sulfur. The novel feature of the process being developed is the superadiabatic combustion (SAC) of part of the H{sub 2}S in the waste stream to provide the thermal energy required for the decomposition reaction such that no additional energy is required. The program is divided into two phases. In Phase 1, detailed thermochemical and kinetic modeling of the SAC reactor withmore » H{sub 2}S-rich fuel gas and air/enriched air feeds is undertaken to evaluate the effects of operating conditions on exit gas products and conversion efficiency, and to identify key process parameters. Preliminary modeling results are used as a basis to conduct a thorough evaluation of SAC process design options, including reactor configuration, operating conditions, and productivity-product separation schemes, with respect to potential product yields, thermal efficiency, capital and operating costs, and reliability, ultimately leading to the preparation of a design package and cost estimate for a bench-scale reactor testing system to be assembled and tested in Phase 2 of the program. A detailed parametric testing plan was also developed for process design optimization and model verification in Phase 2. During Phase 2 of this program, IGT, UIC, and industry advisors UOP and BP Amoco will validate the SAC concept through construction of the bench-scale unit and parametric testing. The computer model developed in Phase 1 will be updated with the experimental data and used in future scale-up efforts. The process design will be refined and the cost estimate updated. Market survey and assessment will continue so that a commercial demonstration project can be identified.« less

Expansion of the wilderness values scale with three sub-scales: Personal maintenance, expression and learning, and societal maintenance

Treesearch

Rudy M. Schuster; Ken Cordell; Gary T. Green

2007-01-01

The purpose of this research was to expand the wilderness value scale administered in the 1994 and 2000 versions of the National Survey on Recreation and the Environment using questions included in the 2003 NSRE. A data set of 1,900 cases was randomly split in half. Validity of the additional questions was tested using principal component analysis, a confirmatory...

Report on all ARRA Funded Technical Work

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

2013-10-05

The main focus of this American Recovery and Reinvestment Act of 2009 (ARRA) funded project was to design an energy efficient carbon capture and storage (CCS) process using the Recipients membrane system for H{sub 2} separation and CO{sub 2} capture. In the ARRA-funded project, the Recipient accelerated development and scale-up of ongoing hydrogen membrane technology research and development (R&D). Specifically, this project focused on accelerating the current R&D work scope of the base program-funded project, involving lab scale tests, detail design of a 250 lb/day H{sub 2} process development unit (PDU), and scale-up of membrane tube and coating manufacturing. Thismore » project scope included the site selection and a Front End Engineering Design (FEED) study of a nominally 4 to 10 ton-per-day (TPD) Pre-Commercial Module (PCM) hydrogen separation membrane system. Process models and techno-economic analysis were updated to include studies on integration of this technology into an Integrated Gasification Combined Cycle (IGCC) power generation system with CCS.« less

Development and evaluation of the INSPIRE measure of staff support for personal recovery.

PubMed

Williams, Julie; Leamy, Mary; Bird, Victoria; Le Boutillier, Clair; Norton, Sam; Pesola, Francesca; Slade, Mike

2015-05-01

No individualised standardised measure of staff support for mental health recovery exists. To develop and evaluate a measure of staff support for recovery. initial draft of measure based on systematic review of recovery processes; consultation (n = 61); and piloting (n = 20). Psychometric evaluation: three rounds of data collection from mental health service users (n = 92). INSPIRE has two sub-scales. The 20-item Support sub-scale has convergent validity (0.60) and adequate sensitivity to change. Exploratory factor analysis (variance 71.4-85.1 %, Kaiser-Meyer-Olkin 0.65-0.78) and internal consistency (range 0.82-0.85) indicate each recovery domain is adequately assessed. The 7-item Relationship sub-scale has convergent validity 0.69, test-retest reliability 0.75, internal consistency 0.89, a one-factor solution (variance 70.5 %, KMO 0.84) and adequate sensitivity to change. A 5-item Brief INSPIRE was also evaluated. INSPIRE and Brief INSPIRE demonstrate adequate psychometric properties, and can be recommended for research and clinical use.

Cross-cultural differences in comorbid symptoms of children with autism spectrum disorders: an international examination between Israel, South Korea, the United Kingdom and the United States of America.

PubMed

Zachor, Ditza; Yang, Jae-Won; Itzchak, Esther Ben; Furniss, Frederick; Pegg, Elinor; Matson, Johnny L; Horovitz, Max; Sipes, Megan; Chung, Kyong-Mee; Jung, Woohyun

2011-01-01

To examine the relationship between culture and symptoms of comorbid psychopathology in those with autism spectrum disorders (ASD). Multivariate analyses of variance (MANOVAs) for each country and each sub-scale of the Autism Spectrum Disorders-Comorbid for Children (ASD-CC). Follow-up independent univariate analyses and post-hoc tests as needed. Separate samples from South Korea, the UK and Israel were compared to a sample from the US in order to examine cultural contributions, using the ASD-CC. Overall, few differences were found. Significantly, the US had significantly higher scores than South Korea on the avoidant sub-scale. Additionally, the US had significantly higher scores than Israel on the over-eating and tantrum sub-scales. No significant differences were found between the US and the UK. Cultural factors, such as views of typical behaviour, should be taken into account when examining symptoms of comorbidity in children with ASD.

A multi-scale residual-based anti-hourglass control for compatible staggered Lagrangian hydrodynamics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kucharik, M.; Scovazzi, Guglielmo; Shashkov, Mikhail Jurievich

Hourglassing is a well-known pathological numerical artifact affecting the robustness and accuracy of Lagrangian methods. There exist a large number of hourglass control/suppression strategies. In the community of the staggered compatible Lagrangian methods, the approach of sub-zonal pressure forces is among the most widely used. However, this approach is known to add numerical strength to the solution, which can cause potential problems in certain types of simulations, for instance in simulations of various instabilities. To avoid this complication, we have adapted the multi-scale residual-based stabilization typically used in the finite element approach for staggered compatible framework. In this study, wemore » describe two discretizations of the new approach and demonstrate their properties and compare with the method of sub-zonal pressure forces on selected numerical problems.« less

A multi-scale residual-based anti-hourglass control for compatible staggered Lagrangian hydrodynamics

DOE PAGES

Kucharik, M.; Scovazzi, Guglielmo; Shashkov, Mikhail Jurievich; ...

2017-10-28

Hourglassing is a well-known pathological numerical artifact affecting the robustness and accuracy of Lagrangian methods. There exist a large number of hourglass control/suppression strategies. In the community of the staggered compatible Lagrangian methods, the approach of sub-zonal pressure forces is among the most widely used. However, this approach is known to add numerical strength to the solution, which can cause potential problems in certain types of simulations, for instance in simulations of various instabilities. To avoid this complication, we have adapted the multi-scale residual-based stabilization typically used in the finite element approach for staggered compatible framework. In this study, wemore » describe two discretizations of the new approach and demonstrate their properties and compare with the method of sub-zonal pressure forces on selected numerical problems.« less

Novel three-dimensional dandelion-like TiO{sub 2} structure with high photocatalytic activity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bai Xuelian; Xie Bin; Pan Nan

2008-03-15

Pure rutile phase crystalline TiO{sub 2} powder with novel 3D dandelion-like structure was synthesized by using a facile hydrothermal method with TiCl{sub 3} as the main starting material. In such a 3D structure, the nanometer-scale construction elements aggregate together and form a micrometer-scale artificial unit. The typical 3D dandelion structure has an average diameter of 1.5-2 {mu}m and is packed radially by nanorods with [001] preference growth direction. Each individual nanorod is hundreds of nanometers in length, and tens of nanometers in diameter. The obtained 3D dandelion-like TiO{sub 2} powder has a high photocatalytic activity, which is equivalent to thatmore » of the commercial available P25 titania powder. Mechanisms of the formation of the dandelion-like structure were also discussed. A different oxidation process of Ti(III) to Ti(IV) during hydrothermal was suggested. - Graphical abstract: Rutile-phase TiO{sub 2} powders with novel 3D dandelion-like structures were synthesized. This kind of 3D artificial hierarchical titania structure has the advantage of reserving the novel nanometer-scale properties while providing us the easiness of storing and handling as we routinely enjoyed for the micrometer-scale materials. A different oxidation process of Ti(III) to Ti(IV) during hydrothermal process was suggested.« less

AirSTAR: A UAV Platform for Flight Dynamics and Control System Testing

NASA Technical Reports Server (NTRS)

Jordan, Thomas L.; Foster, John V.; Bailey, Roger M.; Belcastro, Christine M.

2006-01-01

As part of the NASA Aviation Safety Program at Langley Research Center, a dynamically scaled unmanned aerial vehicle (UAV) and associated ground based control system are being developed to investigate dynamics modeling and control of large transport vehicles in upset conditions. The UAV is a 5.5% (seven foot wingspan), twin turbine, generic transport aircraft with a sophisticated instrumentation and telemetry package. A ground based, real-time control system is located inside an operations vehicle for the research pilot and associated support personnel. The telemetry system supports over 70 channels of data plus video for the downlink and 30 channels for the control uplink. Data rates are in excess of 200 Hz. Dynamic scaling of the UAV, which includes dimensional, weight, inertial, actuation, and control system scaling, is required so that the sub-scale vehicle will realistically simulate the flight characteristics of the full-scale aircraft. This testbed will be utilized to validate modeling methods, flight dynamics characteristics, and control system designs for large transport aircraft, with the end goal being the development of technologies to reduce the fatal accident rate due to loss-of-control.

TESTING SCALING RELATIONS FOR SOLAR-LIKE OSCILLATIONS FROM THE MAIN SEQUENCE TO RED GIANTS USING KEPLER DATA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huber, D.; Bedding, T. R.; Stello, D.

2011-12-20

We have analyzed solar-like oscillations in {approx}1700 stars observed by the Kepler Mission, spanning from the main sequence to the red clump. Using evolutionary models, we test asteroseismic scaling relations for the frequency of maximum power ({nu}{sub max}), the large frequency separation ({Delta}{nu}), and oscillation amplitudes. We show that the difference of the {Delta}{nu}-{nu}{sub max} relation for unevolved and evolved stars can be explained by different distributions in effective temperature and stellar mass, in agreement with what is expected from scaling relations. For oscillation amplitudes, we show that neither (L/M){sup s} scaling nor the revised scaling relation by Kjeldsen andmore » Bedding is accurate for red-giant stars, and demonstrate that a revised scaling relation with a separate luminosity-mass dependence can be used to calculate amplitudes from the main sequence to red giants to a precision of {approx}25%. The residuals show an offset particularly for unevolved stars, suggesting that an additional physical dependency is necessary to fully reproduce the observed amplitudes. We investigate correlations between amplitudes and stellar activity, and find evidence that the effect of amplitude suppression is most pronounced for subgiant stars. Finally, we test the location of the cool edge of the instability strip in the Hertzsprung-Russell diagram using solar-like oscillations and find the detections in the hottest stars compatible with a domain of hybrid stochastically excited and opacity driven pulsation.« less

Testing of some assumptions about biodegradability in soil as measured by carbon dioxide evolution

DOE Office of Scientific and Technical Information (OSTI.GOV)

El-Din Sharabi, N.; Bartha, R.

1993-04-01

The Toxic Substance Control Act calls for a premanufacturing review of novel chemical substances including their biodegradability. Carbon dioxide evolution, using non-labeled carbon or [sup 14]C, is a common method of testing. This study examines assumptions of carbon dioxide evolution testing. Test substances used included: glucose, adipic acid, benzoic acid, and n-hexadecane. Chemical composition other than carbon content appears to influence minimally the percentages conversion to CO[sub 2]. However, that although CO[sub 2] evolution seemed proportional to the carbon content and concentration of the test substance, at least one-half of the evolved net CO[sub 2] did not come directly frommore » the test substance. Conversion to CO[sub 2] in the soil appeared to depend on carbon content only. In experiments of 1 month or longer, the net CO[sub 2] evolution in response to substrate may be above 100% of the added substrate carbon. Whether this applies to all substrate additions remains to be studied. The authors conclude that net CO[sub 2] and [sup 14]CO[sub 2] evolution measurements are useful as a first-tier tests for assessing biodegradability in soil. 11 refs., 6 figs.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grigg, Reid; McPherson, Brian; Lee, Rober

The Southwest Regional Partnership on Carbon Sequestration (SWP) one of seven regional partnerships sponsored by the U.S. Department of Energy (USDOE) carried out five field pilot tests in its Phase II Carbon Sequestration Demonstration effort, to validate the most promising sequestration technologies and infrastructure concepts, including three geologic pilot tests and two terrestrial pilot programs. This field testing demonstrated the efficacy of proposed sequestration technologies to reduce or offset greenhouse gas emissions in the region. Risk mitigation, optimization of monitoring, verification, and accounting (MVA) protocols, and effective outreach and communication were additional critical goals of these field validation tests. Themore » program included geologic pilot tests located in Utah, New Mexico, Texas, and a region-wide terrestrial analysis. Each geologic sequestration test site was intended to include injection of a minimum of ~75,000 tons/year CO{sub 2}, with minimum injection duration of one year. These pilots represent medium- scale validation tests in sinks that host capacity for possible larger-scale sequestration operations in the future. These validation tests also demonstrated a broad variety of carbon sink targets and multiple value-added benefits, including testing of enhanced oil recovery and sequestration, enhanced coalbed methane production and a geologic sequestration test combined with a local terrestrial sequestration pilot. A regional terrestrial sequestration demonstration was also carried out, with a focus on improved terrestrial MVA methods and reporting approaches specific for the Southwest region.« less

PRESSURIZED WATER REACTOR PROGRAM TECHNICAL PROGRESS REPORT FOR THE PERIOD MAY 5, 1955 TO JUNE 16, 1955

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

The current PWR plant and core parameters are listed. Resign requirements are briefly summarized for a radiation monitoring system, a fuel handling water system, a coolant purification system, an electrical power distribution system, and component shielding. Results of studies on thermal bowing and stressing of UO/sub 2/ are reported. A graph is presented of reactor power vs. reactor flow for various hot channel conditions. Development of U-- Mo and U-Nb alloys has been stopped because of the recent selection of UO/sub 2/ fuel material for the PWR core and blanket. The fabrication characteristics of UO/sub 2/ powders are being studied.more » Seamless Zircaloy-2 tubing has been tested to determine elastic limits, bursting pressures, and corrosion resistance. Fabrication techniques and tests for corrosion and defects in Zircaloy-clad U-Mo and UO/sub 2/ fuel rods are described. The preparation of UO/sub 2/ by various methods is being studied to determine which method produces a material most suitable for PWR fuel elements. The stability of UO/sub 2/ compacts in high temperature water and steam is being determined. Surface area and density measurements have been performed on samples of UO/sub 2/ powder prepared by various methods. Revelopment work on U-- Mo and U--Nb alloys has included studies of the effect on corrosion behavior of additions to the test water, additions to the alloys, homogenization of the alloys, annealing times, cladding, and fabrication techniques. Data are presented on relaxation in spring materials after exposure to a corrosive environment. Results are reported from loop and autoclave tests on fission product and crud deposition. Results of irradiation and corrosion testing of clad and unclad U--Mo and U-Nh alloys are described. The UO/sub 2/ irradiation program has included studies of dimensional changes, release of fission gases, and activity in the water surrounding the samples. A review of the methods of calculating reactor physics parameters has been completed, and the established procedures have been applied to determination of PWR reference design parameters. Critical experiments and primary loop shielding analyses are described. (D.E.B.)« less

Testing a Model of Planck-Scale Quantum Geometry With Broadband Correlation of Colocated 40m Interferometers

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCuller, Lee Patrick

2015-12-01

The Holometer is designed to test for a Planck diffractive-scaling uncertainty in long-baseline position measurements due to an underlying noncommutative geometry normalized to relate Black hole entropy bounds of the Holographic principle to the now-finite number of position states. The experiment overlaps two independent 40 meter optical Michelson interferometers to detect the proposed uncertainty as a common broadband length fluctuation. 150 hours of instrument cross-correlation data are analyzed to test the prediction of a correlated noise magnitude ofmore » $$7\\times10^{−21}$$ m/$$\\sqrt{\\rm Hz}$$ with an effective bandwidth of 750kHz. The interferometers each have a quantum-limited sensitivity of $$2.5\\times 10^{−18}$$ m/$$\\sqrt{\\rm Hz}$$, but their correlation with a time-bandwidth product of $$4\\times 10^{11}$$ digs between the noise floors in search for the covarying geometric jitter. The data presents an exclusion of 5 standard deviations for the tested model. This exclusion is defended through analysis of the calibration methods for the instrument as well as further sub shot noise characterization of the optical systems to limit spurious background-correlations from undermining the signal.« less

Mapping stress in polycrystals with sub-10 nm spatial resolution.

PubMed

Polop, C; Vasco, E; Perrino, A P; Garcia, R

2017-09-28

From aircraft to electronic devices, and even in Formula One cars, stress is the main cause of degraded material performance and mechanical failure in applications incorporating thin films and coatings. Over the last two decades, the scientific community has searched for the mechanisms responsible for stress generation in films, with no consensus in sight. The main difficulty is that most current models of stress generation, while atomistic in nature, are based on macroscopic measurements. Here, we demonstrate a novel method for mapping the stress at the surface of polycrystals with sub-10 nm spatial resolution. This method consists of transforming elastic modulus maps measured by atomic force microscopy techniques into stress maps via the local stress-stiffening effect. The validity of this approach is supported by finite element modeling simulations. Our study reveals a strongly heterogeneous distribution of intrinsic stress in polycrystalline Au films, with gradients as high as 100 MPa nm -1 near the grain boundaries. Consequently, our study discloses the limited capacity of macroscopic stress assessments and standard tests to discriminate among models, and the great potential of nanometer-scale stress mapping.

Validating the Physical Activity and Leisure Motivation Scale (PALMS).

PubMed

Molanorouzi, Keyvan; Khoo, Selina; Morris, Tony

2014-09-03

Although there is abundant evidence to recommend a physically active lifestyle, adult physical activity (PA) levels have declined over the past two decades. In order to understand why this happens, numerous studies have been conducted to uncover the reasons for people's participation in PA. Often, the measures used were not broad enough to reflect all the reasons for participation in PA. The Physical Activity and Leisure Motivation Scale (PALMS) was created to be a comprehensive tool measuring motives for participating in PA. This 40-item scale related to participation in sport and PA is designed for adolescents and adults. Five items constitute each of the eight sub-scales (mastery, enjoyment, psychological condition, physical condition, appearance, other's expectations, affiliation, competition/ego) reflecting motives for participation in PA that can be categorized as features of intrinsic and extrinsic motivation based on self-determination theory. The aim of the current study was to validate the PALMS in the cultural context of Malaysia, including to assess how well the PALMS captures the same information as the Recreational Exercise Motivation Measure (REMM). To do so, 502 Malaysian volunteer participants, aged 18 to 67 years (mean ± SD; 31.55 ± 11.87 years), from a variety of PA categories, including individual sports, team sports, martial arts and exercise, completed the study. The hypothesized 8-factor model demonstrated a good fit with the data (CMIN/DF = 2.820, NFI = 0.90, CFI = 0.91, RMSEA = 0.06). Cronbach's alpha coefficient (α = 0.79) indicated good internal consistency for the overall measure. Internal consistency for the PALMS subscales was sound, ranging from 0.78 to 0.82. The correlations between each PALMS sub-scale and the corresponding sub-scale on the validated REMM (the 73-item questionnaire from which the PALMS was developed) were also high and varied from 0.79 to 0.95. Also, test-retest reliability for the questionnaire sub-scales was between 0.78 and 0.94 over a 4-week period. In this sample, the PALMS demonstrated acceptable factor structure, internal consistency, test-retest reliability, and criterion validity. It was applicable to diverse physical activity contexts.

Multi-scale continuum modeling of biological processes: from molecular electro-diffusion to sub-cellular signaling transduction

NASA Astrophysics Data System (ADS)

Cheng, Y.; Kekenes-Huskey, P.; Hake, J. E.; Holst, M. J.; McCammon, J. A.; Michailova, A. P.

2012-01-01

This paper presents a brief review of multi-scale modeling at the molecular to cellular scale, with new results for heart muscle cells. A finite element-based simulation package (SMOL) was used to investigate the signaling transduction at molecular and sub-cellular scales (http://mccammon.ucsd.edu/smol/, http://FETK.org) by numerical solution of the time-dependent Smoluchowski equations and a reaction-diffusion system. At the molecular scale, SMOL has yielded experimentally validated estimates of the diffusion-limited association rates for the binding of acetylcholine to mouse acetylcholinesterase using crystallographic structural data. The predicted rate constants exhibit increasingly delayed steady-state times, with increasing ionic strength, and demonstrate the role of an enzyme's electrostatic potential in influencing ligand binding. At the sub-cellular scale, an extension of SMOL solves a nonlinear, reaction-diffusion system describing Ca2+ ligand buffering and diffusion in experimentally derived rodent ventricular myocyte geometries. Results reveal the important role of mobile and stationary Ca2+ buffers, including Ca2+ indicator dye. We found that alterations in Ca2+-binding and dissociation rates of troponin C (TnC) and total TnC concentration modulate sub-cellular Ca2+ signals. The model predicts that reduced off-rate in the whole troponin complex (TnC, TnI, TnT) versus reconstructed thin filaments (Tn, Tm, actin) alters cytosolic Ca2+ dynamics under control conditions or in disease-linked TnC mutations. The ultimate goal of these studies is to develop scalable methods and theories for the integration of molecular-scale information into simulations of cellular-scale systems.

Monte Carlo Bayesian Inference on a Statistical Model of Sub-gridcolumn Moisture Variability Using High-resolution Cloud Observations . Part II; Sensitivity Tests and Results

NASA Technical Reports Server (NTRS)

da Silva, Arlindo M.; Norris, Peter M.

2013-01-01

Part I presented a Monte Carlo Bayesian method for constraining a complex statistical model of GCM sub-gridcolumn moisture variability using high-resolution MODIS cloud data, thereby permitting large-scale model parameter estimation and cloud data assimilation. This part performs some basic testing of this new approach, verifying that it does indeed significantly reduce mean and standard deviation biases with respect to the assimilated MODIS cloud optical depth, brightness temperature and cloud top pressure, and that it also improves the simulated rotational-Ramman scattering cloud optical centroid pressure (OCP) against independent (non-assimilated) retrievals from the OMI instrument. Of particular interest, the Monte Carlo method does show skill in the especially difficult case where the background state is clear but cloudy observations exist. In traditional linearized data assimilation methods, a subsaturated background cannot produce clouds via any infinitesimal equilibrium perturbation, but the Monte Carlo approach allows finite jumps into regions of non-zero cloud probability. In the example provided, the method is able to restore marine stratocumulus near the Californian coast where the background state has a clear swath. This paper also examines a number of algorithmic and physical sensitivities of the new method and provides guidance for its cost-effective implementation. One obvious difficulty for the method, and other cloud data assimilation methods as well, is the lack of information content in the cloud observables on cloud vertical structure, beyond cloud top pressure and optical thickness, thus necessitating strong dependence on the background vertical moisture structure. It is found that a simple flow-dependent correlation modification due to Riishojgaard (1998) provides some help in this respect, by better honoring inversion structures in the background state.

Impact of CT attenuation correction method on quantitative respiratory-correlated (4D) PET/CT imaging

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nyflot, Matthew J., E-mail: nyflot@uw.edu; Lee, Tzu-Cheng; Alessio, Adam M.

Purpose: Respiratory-correlated positron emission tomography (PET/CT) 4D PET/CT is used to mitigate errors from respiratory motion; however, the optimal CT attenuation correction (CTAC) method for 4D PET/CT is unknown. The authors performed a phantom study to evaluate the quantitative performance of CTAC methods for 4D PET/CT in the ground truth setting. Methods: A programmable respiratory motion phantom with a custom movable insert designed to emulate a lung lesion and lung tissue was used for this study. The insert was driven by one of five waveforms: two sinusoidal waveforms or three patient-specific respiratory waveforms. 3DPET and 4DPET images of the phantommore » under motion were acquired and reconstructed with six CTAC methods: helical breath-hold (3DHEL), helical free-breathing (3DMOT), 4D phase-averaged (4DAVG), 4D maximum intensity projection (4DMIP), 4D phase-matched (4DMATCH), and 4D end-exhale (4DEXH) CTAC. Recovery of SUV{sub max}, SUV{sub mean}, SUV{sub peak}, and segmented tumor volume was evaluated as RC{sub max}, RC{sub mean}, RC{sub peak}, and RC{sub vol}, representing percent difference relative to the static ground truth case. Paired Wilcoxon tests and Kruskal–Wallis ANOVA were used to test for significant differences. Results: For 4DPET imaging, the maximum intensity projection CTAC produced significantly more accurate recovery coefficients than all other CTAC methods (p < 0.0001 over all metrics). Over all motion waveforms, ratios of 4DMIP CTAC recovery were 0.2 ± 5.4, −1.8 ± 6.5, −3.2 ± 5.0, and 3.0 ± 5.9 for RC{sub max}, RC{sub peak}, RC{sub mean}, and RC{sub vol}. In comparison, recovery coefficients for phase-matched CTAC were −8.4 ± 5.3, −10.5 ± 6.2, −7.6 ± 5.0, and −13.0 ± 7.7 for RC{sub max}, RC{sub peak}, RC{sub mean}, and RC{sub vol}. When testing differences between phases over all CTAC methods and waveforms, end-exhale phases were significantly more accurate (p = 0.005). However, these differences were driven by the patient-specific respiratory waveforms; when testing patient and sinusoidal waveforms separately, patient waveforms were significantly different between phases (p < 0.0001) while the sinusoidal waveforms were not significantly different (p = 0.98). When considering only the subset of 4DMATCH images that corresponded to the end-exhale image phase, 4DEXH, mean and interquartile range were similar to 4DMATCH but variability was considerably reduced. Conclusions: Comparative advantages in accuracy and precision of SUV metrics and segmented volumes were demonstrated with the use of the maximum intensity projection and end-exhale CT attenuation correction. While respiratory phase-matched CTAC should in theory provide optimal corrections, image artifacts and differences in implementation of 4DCT and 4DPET sorting can degrade the benefit of this approach. These results may be useful to guide the implementation, analysis, and development of respiratory-correlated thoracic PET/CT in the radiation oncology and diagnostic settings.« less

Acoustic travel time gauges for in-situ determination of pressure and temperature in multi-anvil apparatus

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Xuebing; Chen, Ting; Qi, Xintong

In this study, we developed a new method for in-situ pressure determination in multi-anvil, high-pressure apparatus using an acoustic travel time approach within the framework of acoustoelasticity. The ultrasonic travel times of polycrystalline Al{sub 2}O{sub 3} were calibrated against NaCl pressure scale up to 15 GPa and 900 °C in a Kawai-type double-stage multi-anvil apparatus in conjunction with synchrotron X-radiation, thereby providing a convenient and reliable gauge for pressure determination at ambient and high temperatures. The pressures derived from this new travel time method are in excellent agreement with those from the fixed-point methods. Application of this new pressure gauge in anmore » offline experiment revealed a remarkable agreement of the densities of coesite with those from the previous single crystal compression studies under hydrostatic conditions, thus providing strong validation for the current travel time pressure scale. The travel time approach not only can be used for continuous in-situ pressure determination at room temperature, high temperatures, during compression and decompression, but also bears a unique capability that none of the previous scales can deliver, i.e., simultaneous pressure and temperature determination with a high accuracy (±0.16 GPa in pressure and ±17 °C in temperature). Therefore, the new in-situ Al{sub 2}O{sub 3} pressure gauge is expected to enable new and expanded opportunities for offline laboratory studies of solid and liquid materials under high pressure and high temperature in multi-anvil apparatus.« less

Towards 3D printed multifunctional immobilization for proton therapy: Initial materials characterization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Michiels, Steven, E-mail: michiels.steven@kuleuven

Purpose: 3D printing technology is investigated for the purpose of patient immobilization during proton therapy. It potentially enables a merge of patient immobilization, bolus range shifting, and other functions into one single patient-specific structure. In this first step, a set of 3D printed materials is characterized in detail, in terms of structural and radiological properties, elemental composition, directional dependence, and structural changes induced by radiation damage. These data will serve as inputs for the design of 3D printed immobilization structure prototypes. Methods: Using four different 3D printing techniques, in total eight materials were subjected to testing. Samples with a nominalmore » dimension of 20 × 20 × 80 mm{sup 3} were 3D printed. The geometrical printing accuracy of each test sample was measured with a dial gage. To assess the mechanical response of the samples, standardized compression tests were performed to determine the Young’s modulus. To investigate the effect of radiation on the mechanical response, the mechanical tests were performed both prior and after the administration of clinically relevant dose levels (70 Gy), multiplied with a safety factor of 1.4. Dual energy computed tomography (DECT) methods were used to calculate the relative electron density to water ρ{sub e}, the effective atomic number Z{sub eff}, and the proton stopping power ratio (SPR) to water SPR. In order to validate the DECT based calculation of radiological properties, beam measurements were performed on the 3D printed samples as well. Photon irradiations were performed to measure the photon linear attenuation coefficients, while proton irradiations were performed to measure the proton range shift of the samples. The directional dependence of these properties was investigated by performing the irradiations for different orientations of the samples. Results: The printed test objects showed reduced geometric printing accuracy for 2 materials (deviation > 0.25 mm). Compression tests yielded Young’s moduli ranging from 0.6 to 2940 MPa. No deterioration in the mechanical response was observed after exposure of the samples to 100 Gy in a therapeutic MV photon beam. The DECT-based characterization yielded Z{sub eff} ranging from 5.91 to 10.43. The SPR and ρ{sub e} both ranged from 0.6 to 1.22. The measured photon attenuation coefficients at clinical energies scaled linearly with ρ{sub e}. Good agreement was seen between the DECT estimated SPR and the measured range shift, except for the higher Z{sub eff}. As opposed to the photon attenuation, the proton range shifting appeared to be printing orientation dependent for certain materials. Conclusions: In this study, the first step toward 3D printed, multifunctional immobilization was performed, by going through a candidate clinical workflow for the first time: from the material printing to DECT characterization with a verification through beam measurements. Besides a proof of concept for beam modification, the mechanical response of printed materials was also investigated to assess their capabilities for positioning functionality. For the studied set of printing techniques and materials, a wide variety of mechanical and radiological properties can be selected from for the intended purpose. Moreover the elaborated hybrid DECT methods aid in performing in-house quality assurance of 3D printed components, as these methods enable the estimation of the radiological properties relevant for use in radiation therapy.« less

Unique Testing Capabilities of the NASA Langley Transonic Dynamics Tunnel, an Exercise in Aeroelastic Scaling

NASA Technical Reports Server (NTRS)

Ivanco, Thomas G.

2013-01-01

NASA Langley Research Center's Transonic Dynamics Tunnel (TDT) is the world's most capable aeroelastic test facility. Its large size, transonic speed range, variable pressure capability, and use of either air or R-134a heavy gas as a test medium enable unparalleled manipulation of flow-dependent scaling quantities. Matching these scaling quantities enables dynamic similitude of a full-scale vehicle with a sub-scale model, a requirement for proper characterization of any dynamic phenomenon, and many static elastic phenomena. Select scaling parameters are presented in order to quantify the scaling advantages of TDT and the consequence of testing in other facilities. In addition to dynamic testing, the TDT is uniquely well-suited for high risk testing or for those tests that require unusual model mount or support systems. Examples of recently conducted dynamic tests requiring unusual model support are presented. In addition to its unique dynamic test capabilities, the TDT is also evaluated in its capability to conduct aerodynamic performance tests as a result of its flow quality. Results of flow quality studies and a comparison to a many other transonic facilities are presented. Finally, the ability of the TDT to support future NASA research thrusts and likely vehicle designs is discussed.

Temperature and acidity effects on WO{sub 3} nanostructures and gas-sensing properties of WO{sub 3} nanoplates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Huili; Liu, Zhifang; Yang, Jiaqin

2014-09-15

Graphical abstract: Generally, large acid quantity and high temperature are beneficial to the formation of anhydrous WO3, but the acidity effect on the crystal phase is weaker than that of temperature. Large acid quantity is found helpful to the oriented growth of tungsten oxides, forming a nanoplate-like product. - Highlights: • Large acid quantity is propitious to the oriented growth of a WO{sub 3} nanoplate. • Effect of acid quantity on crystal phases of products is weaker than that of temperature. • One step hydrothermal synthesis of WO{sub 3} is facile and can be easily scaled up. • A WO{submore » 3} nanoplate shows a fast response and distinct sensing selectivity to acetone gas. - Abstract: WO{sub 3} nanostructures were successfully synthesized by a facile hydrothermal method using Na{sub 2}WO{sub 4}·2H{sub 2}O and HNO{sub 3} as raw materials. They are characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscope (TEM). The specific surface area was obtained from N{sub 2} adsorption–desorption isotherm. The effects of the amount of HNO{sub 3}, hydrothermal temperature and reaction time on the crystal phases and morphologies of the WO{sub 3} nanostructures were investigated in detail, and the reaction mechanism was discussed. Large amount of acid is found for the first time to be helpful to the oriented growth of tungsten oxides, forming nanoplate-like products, while hydrothermal temperature has more influence on the crystal phase of the product. Gas-sensing properties of the series of as-prepared WO{sub 3} nanoplates were tested by means of acetone, ethanol, formaldehyde and ammonia. One of the WO{sub 3} nanoplates with high specific surface area and high crystallinity displays high sensitivity, fast response and distinct sensing selectivity to acetone gas.« less

The Uncertainty of Mass Discharge Measurements Using Pumping Methods Under Simplified Conditions

EPA Science Inventory

Mass discharge measurements at contaminated sites have been used to assist with site management decisions, and can be divided into two broad categories: point-scale measurement techniques and pumping methods. Pumping methods can be sub-divided based on the pumping procedures use...

Method of testing gear wheels in impact bending

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tikhonov, A.K.; Palagin, Y.M.

1995-05-01

Chemicothermal treatment processes are widely used in engineering to improve the working lives of important components, of which the most common is nitrocementation. That process has been applied at the Volga Automobile Plant mainly to sprockets in gear transmissions, which need high hardness and wear resistance in the surfaces with relatively ductile cores. Although various forms of chemicothermal treatment are widely used, there has been no universal method of evaluating the strengths of gear wheels. Standard methods of estimating strength ({sigma}{sub u}, {sigma}{sub t}, {sigma}{sub b}, and hardness) have a major shortcoming: They can determine only the characteristics of themore » cores for case-hardened materials. Here we consider a method of impact bending test, which enables one to evaluate the actual strength of gear teeth.« less

A spectral radius scaling semi-implicit iterative time stepping method for reactive flow simulations with detailed chemistry

NASA Astrophysics Data System (ADS)

Xie, Qing; Xiao, Zhixiang; Ren, Zhuyin

2018-09-01

A spectral radius scaling semi-implicit time stepping scheme has been developed for simulating unsteady compressible reactive flows with detailed chemistry, in which the spectral radius in the LUSGS scheme has been augmented to account for viscous/diffusive and reactive terms and a scalar matrix is proposed to approximate the chemical Jacobian using the minimum species destruction timescale. The performance of the semi-implicit scheme, together with a third-order explicit Runge-Kutta scheme and a Strang splitting scheme, have been investigated in auto-ignition and laminar premixed and nonpremixed flames of three representative fuels, e.g., hydrogen, methane, and n-heptane. Results show that the minimum species destruction time scale can well represent the smallest chemical time scale in reactive flows and the proposed scheme can significantly increase the allowable time steps in simulations. The scheme is stable when the time step is as large as 10 μs, which is about three to five orders of magnitude larger than the smallest time scales in various tests considered. For the test flames considered, the semi-implicit scheme achieves second order of accuracy in time. Moreover, the errors in quantities of interest are smaller than those from the Strang splitting scheme indicating the accuracy gain when the reaction and transport terms are solved coupled. Results also show that the relative efficiency of different schemes depends on fuel mechanisms and test flames. When the minimum time scale in reactive flows is governed by transport processes instead of chemical reactions, the proposed semi-implicit scheme is more efficient than the splitting scheme. Otherwise, the relative efficiency depends on the cost in sub-iterations for convergence within each time step and in the integration for chemistry substep. Then, the capability of the compressible reacting flow solver and the proposed semi-implicit scheme is demonstrated for capturing the hydrogen detonation waves. Finally, the performance of the proposed method is demonstrated in a two-dimensional hydrogen/air diffusion flame.

Tentative test method for nitrogen oxides (combined) content in the atmosphere by the Griess--Saltzman reaction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1977-01-01

A spectrophotometric method is described for the determination of the combined NO/sub 2/ and NO in the atmosphere. The NO is quantitatively converted to NO/sub 2/ by a chromic acid oxidizer, and this resulting NO/sub 2/ plus the NO/sub 2/ already present in the air sample are absorbed in an azo-dye forming reagent. Within 15 min a red-violet color is produced which is measured spectrophotometrically at 550 nm. The method is applicable to the determination of 0.002 to 5 ppM.

Manual of Scaling Methods

NASA Technical Reports Server (NTRS)

Bond, Thomas H. (Technical Monitor); Anderson, David N.

2004-01-01

This manual reviews the derivation of the similitude relationships believed to be important to ice accretion and examines ice-accretion data to evaluate their importance. Both size scaling and test-condition scaling methods employing the resulting similarity parameters are described, and experimental icing tests performed to evaluate scaling methods are reviewed with results. The material included applies primarily to unprotected, unswept geometries, but some discussion of how to approach other situations is included as well. The studies given here and scaling methods considered are applicable only to Appendix-C icing conditions. Nearly all of the experimental results presented have been obtained in sea-level tunnels. Recommendations are given regarding which scaling methods to use for both size scaling and test-condition scaling, and icing test results are described to support those recommendations. Facility limitations and size-scaling restrictions are discussed. Finally, appendices summarize the air, water and ice properties used in NASA scaling studies, give expressions for each of the similarity parameters used and provide sample calculations for the size-scaling and test-condition scaling methods advocated.

Cross-cultural adaptation of the short-form condom attitude scale: validity assessment in a sub-sample of rural-to-urban migrant workers in Bangladesh

PubMed Central

2013-01-01

Background The reliable and valid measurement of attitudes towards condom use are essential to assist efforts to design population specific interventions aimed at promoting positive attitude towards, and increased use of condoms. Although several studies, mostly in English speaking western world, have demonstrated the utility of condom attitude scales, very limited culturally relevant condom attitude measures have been developed till to date. We have developed a scale and evaluated its psychometric properties in a sub-sample of rural-to-urban migrant workers in Bangladesh. Methods This paper reports mostly on cross-sectional survey components of a mixed methods sexual health research in Bangladesh. The survey sample (n = 878) comprised rural-to-urban migrant taxi drivers (n = 437) and restaurant workers (n = 441) in Dhaka (aged 18–35 years). The study also involved focus group sessions with same populations to establish the content validity and cultural equivalency of the scale. The current scale was administered with a large sexual health survey questionnaire and consisted of 10 items. Quantitative and qualitative data were assessed with statistical and thematic analysis, respectively, and then presented. Results The participants found the scale simple and easy to understand and use. The internal consistency (α) of the scale was 0.89 with high construct validity (the first component accounted for about 52% of variance and second component about 20% of the total variance with an Eigen-value for both factors greater than one). The test-retest reliability (repeatability) was also found satisfactory with high inter-item correlations (the majority of the intra-class correlation coefficient values was above 2 and was significant for all items on the scale, p < 0.001). The 2-week repeatability assessed by the Pearson product–moment correlation coefficient was 0.75. Conclusion The results indicated that Bengali version of the scale have good metric properties for assessing attitudes toward condom use. Validated scale is a short, simple and reliable instrument for measuring attitudes towards condom use in vulnerable populations like current study sample. This culturally-customized scale can be used to monitor the progress of condom uptake and promotion activities in Bangladesh or similar settings. PMID:23510383

Iron-Based Amorphous Coatings Produced by HVOF Thermal Spray Processing-Coating Structure and Properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beardsley, M B

2008-03-26

The feasibility to coat large SNF/HLW containers with a structurally amorphous material (SAM) was demonstrated on sub-scale models fabricated from Type 316L stainless steel. The sub-scale model were coated with SAM 1651 material using kerosene high velocity oxygen fuel (HVOF) torch to thicknesses ranging from 1 mm to 2 mm. The process parameters such as standoff distance, oxygen flow, and kerosene flow, were optimized in order to improve the corrosion properties of the coatings. Testing in an electrochemical cell and long-term exposure to a salt spray environment were used to guide the selection of process parameters.

Cold dark matter confronts the cosmic microwave background - Large-angular-scale anisotropies in Omega sub 0 + lambda 1 models

NASA Technical Reports Server (NTRS)

Gorski, Krzysztof M.; Silk, Joseph; Vittorio, Nicola

1992-01-01

A new technique is used to compute the correlation function for large-angle cosmic microwave background anisotropies resulting from both the space and time variations in the gravitational potential in flat, vacuum-dominated, cold dark matter cosmological models. Such models with Omega sub 0 of about 0.2, fit the excess power, relative to the standard cold dark matter model, observed in the large-scale galaxy distribution and allow a high value for the Hubble constant. The low order multipoles and quadrupole anisotropy that are potentially observable by COBE and other ongoing experiments should definitively test these models.

Nuclear test ban treaty verification: Improving test ban monitoring with empirical and model-based signal processing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harris, David B.; Gibbons, Steven J.; Rodgers, Arthur J.

In this approach, small scale-length medium perturbations not modeled in the tomographic inversion might be described as random fields, characterized by particular distribution functions (e.g., normal with specified spatial covariance). Conceivably, random field parameters (scatterer density or scale length) might themselves be the targets of tomographic inversions of the scattered wave field. As a result, such augmented models may provide processing gain through the use of probabilistic signal sub spaces rather than deterministic waveforms.

Nuclear test ban treaty verification: Improving test ban monitoring with empirical and model-based signal processing

DOE PAGES

Harris, David B.; Gibbons, Steven J.; Rodgers, Arthur J.; ...

2012-05-01

In this approach, small scale-length medium perturbations not modeled in the tomographic inversion might be described as random fields, characterized by particular distribution functions (e.g., normal with specified spatial covariance). Conceivably, random field parameters (scatterer density or scale length) might themselves be the targets of tomographic inversions of the scattered wave field. As a result, such augmented models may provide processing gain through the use of probabilistic signal sub spaces rather than deterministic waveforms.

Modeling of Revitalization of Atmospheric Water

NASA Technical Reports Server (NTRS)

Coker, Robert; Knox, Jim

2014-01-01

The Atmosphere Revitalization Recovery and Environmental Monitoring (ARREM) project was initiated in September of 2011 as part of the Advanced Exploration Systems (AES) program. Under the ARREM project, testing of sub-scale and full-scale systems has been combined with multiphysics computer simulations for evaluation and optimization of subsystem approaches. In particular, this paper describes the testing and modeling of the water desiccant subsystem of the carbon dioxide removal assembly (CDRA). The goal is a full system predictive model of CDRA to guide system optimization and development.

Revisiting the blocking force test on ferroelectric ceramics using high energy x-ray diffraction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daniel, L., E-mail: laurent.daniel@u-psud.fr; GeePs; Hall, D. A.

2015-05-07

The blocking force test is a standard test to characterise the properties of piezoelectric actuators. The aim of this study is to understand the various contributions to the macroscopic behaviour observed during this experiment that involves the intrinsic piezoelectric effect, ferroelectric domain switching, and internal stress development. For this purpose, a high energy diffraction experiment is performed in-situ during a blocking force test on a tetragonal lead zirconate titanate (PZT) ceramic (Pb{sub 0.98}Ba{sub 0.01}(Zr{sub 0.51}Ti{sub 0.49}){sub 0.98}Nb{sub 0.02}O{sub 3}). It is shown that the usual macroscopic linear interpretation of the test can also be performed at the single crystal scale,more » allowing the identification of local apparent piezoelectric and elastic properties. It is also shown that despite this apparent linearity, the blocking force test involves significant non-linear behaviour mostly due to domain switching under electric field and stress. Although affecting a limited volume fraction of the material, domain switching is responsible for a large part of the macroscopic strain and explains the high level of inter- and intra-granular stresses observed during the course of the experiment. The study shows that if apparent piezoelectric and elastic properties can be identified for PZT single crystals from blocking stress curves, they may be very different from the actual properties of polycrystalline materials due to the multiplicity of the physical mechanisms involved. These apparent properties can be used for macroscopic modelling purposes but should be considered with caution if a local analysis is aimed at.« less

Bench-Scale Development of a Hot Carbonate Absorption Process with Crystallization-Enabled High-Pressure Stripping for Post-Combustion CO{sub 2} Capture

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lu, Yongqi; DeVries, Nicholas; Ruhter, David

A novel Hot Carbonate Absorption Process with Crystallization-Enabled High-Pressure Stripping (Hot-CAP) has been developed by the University of Illinois at Urbana-Champaign and Carbon Capture Scientific, LLC in this three-year, bench-scale project. The Hot-CAP features a concentrated carbonate solution (e.g., K{sub 2}CO{sub 3}) for CO{sub 2} absorption and a bicarbonate slurry (e.g., KHCO{sub 3}) for high-pressure CO{sub 2} stripping to overcome the energy use and other disadvantages associated with the benchmark monoethanolamine (MEA) process. The project was aimed at performing laboratory- and bench-scale experiments to prove its technical feasibility and generate process engineering and scale-up data, and conducting a techno-economic analysismore » (TEA) to demonstrate its energy use and cost competitiveness over MEA. To meet project goals and objectives, a combination of experimental, modeling, process simulation, and economic analysis studies were applied. Carefully designed and intensive experiments were conducted to measure thermodynamic and reaction engineering data relevant to four major unit operations in the Hot-CAP (i.e., CO{sub 2} absorption, CO{sub 2} stripping, bicarbonate crystallization, and sulfate reclamation). The rate promoters that could accelerate the CO{sub 2} absorption rate into the potassium carbonate/bicarbonate (PCB) solution to a level greater than that into the 5 M MEA solution were identified, and the superior performance of CO{sub 2} absorption into PCB was demonstrated in a bench-scale packed-bed column. Kinetic data on bicarbonate crystallization were developed and applied for crystallizer design and sizing. Parametric testing of high-pressure CO{sub 2} stripping with concentrated bicarbonate-dominant slurries at high temperatures ({>=}140{degrees}C) in a bench-scale stripping column demonstrated lower heat use than with MEA. The feasibility of a modified process for combining SO{sub 2} removal with CO{sub 2} capture was preliminarily demonstrated. In addition to the experimental studies, the technical challenges pertinent to fouling of slurry-handling equipment and the design of the crystallizer and stripper were addressed through consultation with vendors and engineering analyses. A process flow diagram of the Hot-CAP was then developed and a TEA was performed to compare the energy use and cost performance of a nominal 550-MWe subcritical pulverized coal (PC)-fired power plant without CO{sub 2} capture (DOE/NETL Case 9) with the benchmark MEA-based post-combustion CO{sub 2} capture (PCC; DOE/NETL Case 10) and the Hot-CAP-based PCC. The results revealed that the net power produced in the PC + Hot-CAP is 609 MWe, greater than the PC + MEA (550 MWe). The 20-year levelized cost of electricity (LCOE) for the PC + Hot-CAP, including CO{sub 2} transportation and storage, is 120.3 mills/kWh, a 60% increase over the base PC plant without CO{sub 2} capture. The LCOE increase for the Hot-CAP is 29% lower than that for MEA. TEA results demonstrated that the Hot-CAP is energy-efficient and cost-effective compared with the benchmark MEA process.« less

Methodologies in determining mechanical properties of thin films using nanoindentation

NASA Astrophysics Data System (ADS)

Han, Seung Min Jane

Thin films are critical components of microelectronic and MEMS devices, and evaluating their mechanical properties is of current interest. As the dimensions of the devices become smaller and smaller, however, understanding the mechanical properties of materials at sub-micron length scales becomes more challenging. The conventional methods for evaluating strengths of materials in bulk form cannot be applied, and new methodologies are required for accurately evaluating mechanical properties of thin films. In this work, development of methodologies using the nanoindenter was pursued in three parts: (1) creation of a new method for extracting thin film hardness, (2) use of combinatorial methods for determining compositions with desired mechanical properties, and (3) use of microcompression testing of sub-micron sized pillars to understand plasticity in Al-Sc multilayers. The existing nanoindentation hardness model by Oliver & Pharr is unable to accurately determine the hardness of thin films on substrates with an elastic mismatch. Thus, a new method of analysis for extracting thin film hardness from film/substrate systems, that eliminates the effect of elastic mismatch of the underlying substrate, surface roughness, and also pile-up/sink-in, is needed. Such a method was developed in the first part of this study. The feasibility of using the nanoindentation hardness together with combinatorial methods to efficiently scan through mechanical properties of Ti-Al metallic alloys was examined in the second part of this study. The combinatorial approach provides an efficient method that can be used to determine alloy compositions that might merit further exploration and development as bulk materials. Finally, the mechanical properties of Al-Al3Sc multilayers with bilayer periods ranging from 6-100 nm were examined using microcompression. The sub-micron sized pillars were prepared using the focused ion beam (FIB) and compression tested with the flat tip of the nanoindenter. The measured yield strengths show the trend of increasing strength with decreasing bilayer period, and agree with the nanoindentation hardness results using the suitable Tabor correction factor. Strain softening was observed at large strains, and a new model for the true stress and true strain was developed to account for the inhomogeneous deformation geometry.

Methods for Scaling Icing Test Conditions

NASA Technical Reports Server (NTRS)

Anderson, David N.

1995-01-01

This report presents the results of tests at NASA Lewis to evaluate several methods to establish suitable alternative test conditions when the test facility limits the model size or operating conditions. The first method was proposed by Olsen. It can be applied when full-size models are tested and all the desired test conditions except liquid-water content can be obtained in the facility. The other two methods discussed are: a modification of the French scaling law and the AEDC scaling method. Icing tests were made with cylinders at both reference and scaled conditions representing mixed and glaze ice in the NASA Lewis Icing Research Tunnel. Reference and scale ice shapes were compared to evaluate each method. The Olsen method was tested with liquid-water content varying from 1.3 to .8 g/m(exp3). Over this range, ice shapes produced using the Olsen method were unchanged. The modified French and AEDC methods produced scaled ice shapes which approximated the reference shapes when model size was reduced to half the reference size for the glaze-ice cases tested.

Summer Work Experience: Determining Methane Combustion Mechanisms and Sub-Scale Diffuser Properties for Space Transporation System Engine Testing

NASA Technical Reports Server (NTRS)

Williams, Powtawche N.

1998-01-01

To assess engine performance during the testing of Space Shuttle Main Engines (SSMEs), the design of an optimal altitude diffuser is studied for future Space Transportation Systems (STS). For other Space Transportation Systems, rocket propellant using kerosene is also studied. Methane and dodecane have similar reaction schemes as kerosene, and are used to simulate kerosene combustion processes at various temperatures. The equations for the methane combustion mechanism at high temperature are given, and engine combustion is simulated on the General Aerodynamic Simulation Program (GASP). The successful design of an altitude diffuser depends on the study of a sub-scaled diffuser model tested through two-dimensional (2-D) flow-techniques. Subroutines given calculate the static temperature and pressure at each Mach number within the diffuser flow. Implementing these subroutines into program code for the properties of 2-D compressible fluid flow determines all fluid characteristics, and will be used in the development of an optimal diffuser design.

Exposures to war-related traumatic events and post-traumatic stress disorder symptoms among displaced Darfuri female university students: an exploratory study

PubMed Central

2012-01-01

Background With the deaths of hundreds of thousands and the displacement of up to three million Darfuris, the increasingly complex and on-going war in Darfur has warranted the need to investigate war-related severity and current mental health levels amongst its civilian population. The purpose of this study is to explore the association between war-related exposures and assess post-traumatic stress disorder (PTSD) symptoms amongst a sample of Darfuri female university students at Ahfad University for Women (AUW) in Omdurman city. Methods An exploratory cross-sectional study among a representative sample of Darfuri female university students at AUW (N = 123) was conducted in February 2010. Using an adapted version of the Harvard Trauma Questionnaire (HTQ), war-related exposures and post-traumatic stress disorder (PTSD) symptoms were assessed. Means and standard deviations illustrated the experiential severity of war exposure dimensions and PTSD symptom sub-scales, while Pearson correlations tested for the strength of association between dimensions of war exposures and PTSD symptom sub-scales. Results Approximately 42 % of the Darfuri participants reported being displaced and 54 % have experienced war-related traumatic exposures either as victims or as witnesses (M = 28, SD = 14.24, range 0 – 40 events). Also, there was a strong association between the experiential dimension of war-related trauma exposures and the full symptom of PTSD. Moreover, the refugee-specific self-perception of functioning sub-scale within the PTSD measurement scored a mean of 3.2 (SD = .56), well above the 2.0 cut-off. Conclusions This study provides evidence for a relationship between traumatic war-related exposures and symptom rates of PTSD among AUW Darfuri female students. Findings are discussed in terms of AUW counseling service improvement. PMID:22863107

The Viability of Hearing Protection Device Fit-Testing at Navy and Marine Corps Accession Points

PubMed Central

Federman, Jeremy; Duhon, Christon

2016-01-01

Introduction: The viability of hearing protection device (HPD) verification (i.e., fit-testing) on a large scale was investigated to address this gap in a military accession environment. Materials and Methods: Personal Attenuation Ratings (PARs) following self-fitted (SELF-Fit) HPDs were acquired from 320 US Marine Corps training recruits (87.5% male, 12.5% female) across four test protocols (1-, 3-, 5-, and 7- frequency). SELF-Fit failures received follow-up to assess potential causes. Follow-up PARs were acquired (Experimenter fit [EXP-Fit], followed by Subject re-fit [SUB Re-Fit]). EXP-Fit was intended to provide a perception (dubbed “ear canal muscle memory”) of what a correctly fitted HPD should feel like. SUB Re-Fit was completed following EXP-Fit to determine whether a training recruit could duplicate EXP-Fit on her/his own without assistance. Results: A one-way analysis of variance (ANOVA) (N=320) showed that SELF-Fit means differed significantly between protocols (P < 0.001). Post-hoc analyses showed that the 1-freq SELF-Fit mean was significantly lower than all other protocols (P < 0.03) by 5.6 dB or more. No difference was found between the multi-frequency protocols. For recruits who were followed up with EXP-Fit (n=79), across all protocols, a significant (P < 0.001) mean improvement of 25.68 dB (10.99) was found, but PARs did not differ (P = 0.99) between EXP-Fit protocols. For recruits in the 3-freq and 5-freq protocol groups who experienced all three PAR test methods (n=33), PAR methods differed (P < 0.001) but no method by protocol interaction was found (P = 0.46). Post hoc tests showed that both EXP-Fit and SUB Re-Fit had significantly better attenuation than SELF-Fit (P < 0.001), but no difference was found between EXPFit and SUB Re-Fit (P = 0.59). For SELF-Fit, the 1-freq protocol resulted in a 35% pass rate, whereas the 3-, 5-, and 7-freq protocols resulted in >60% pass rates. Results showed that once recruits experienced how HPDs should feel when inserted correctly, they were able to properly replicate the procedure with similar results to the expert fit suggesting “ear canal muscle memory” may be a viable training strategy concomitant with HPD verification. Fit-test duration was also measured to examine the tradeoff between results accuracy and time required to complete each protocol. Discussion: Results from this study showed the critical importance of initial selection and fitting of HPDs followed by verification (i.e., fit-testing) at Navy and Marine Corps accession points. Achieving adequate protection from an HPD is fundamentally dependent on obtaining proper fit of the issued HPD as well as the quality of training recruits receive regarding HPD use. PMID:27991461

The X-40 sub-scale technology demonstrator and its U.S. Army CH-47 Chinook helicopter mothership fly over a dry lakebed runway during a captive-carry test flight at NASA's Dryden Flight Research Center

NASA Image and Video Library

2000-12-08

The X-40 sub-scale technology demonstrator and its U.S. Army CH-47 Chinook helicopter mothership fly over a dry lakebed runway during a captive-carry test flight from NASA's Dryden Flight Research Center, Edwards, California. The X-40 is attached to a sling which is suspended from the CH-47 by a 110-foot-long cable during the tests, while a small parachute trails behind to provide stability. The captive carry flights are designed to verify the X-40's navigation and control systems, rigging angles for its sling, and stability and control of the helicopter while carrying the X-40 on a tether. Following a series of captive-carry flights, the X-40 made free flights from a launch altitude of about 15,000 feet above ground, gliding to a fully autonomous landing. The X-40 is an unpowered 82 percent scale version of the X-37, a Boeing-developed spaceplane designed to demonstrate various advanced technologies for development of future lower-cost access to space vehicles.

Solar Reforming of Carbon Dioxide to Produce Diesel Fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dennis Schuetzle; Robert Schuetzle

2010-12-31

This project focused on the demonstration of an innovative technology, referred to as the Sunexus CO2 Solar Reformer, which utilizes waste CO2 as a feedstock for the efficient and economical production of synthetic diesel fuel using solar thermal energy as the primary energy input. The Sunexus technology employs a two stage process for the conversion of CO2 to diesel fuel. A solar reforming system, including a specially designed reactor and proprietary CO2 reforming catalyst, was developed and used to convert captured CO2 rich gas streams into syngas (primarily hydrogen and carbon monoxide) using concentrated solar energy at high conversion efficiencies.more » The second stage of the system (which has been demonstrated under other funding) involves the direct conversion of the syngas into synthetic diesel fuel using a proprietary catalyst (Terra) previously developed and validated by Pacific Renewable Fuels and Chemicals (PRFC). The overall system energy efficiency for conversion of CO2 to diesel fuel is 74%, due to the use of solar energy. The results herein describe modeling, design, construction, and testing of the Sunexus CO2 Solar Reformer. Extensive parametric testing of the solar reformer and candidate catalysts was conducted and chemical kinetic models were developed. Laboratory testing of the Solar Reformer was successfully completed using various gas mixtures, temperatures, and gas flow rates/space velocities to establish performance metrics which can be employed for the design of commercial plants. A variety of laboratory tests were conducted including dry reforming (CO2 and CH{sub 4}), combination dry/steam reforming (CO2, CH{sub 4} & H{sub 2}O), and tri-reforming (CO2, CH{sub 4}, H{sub 2}O & O{sub 2}). CH{sub 4} and CO2 conversions averaged 95-100% and 50-90% per reformer cycle, respectively, depending upon the temperatures and gas space velocities. No formation of carbon deposits (coking) on the catalyst was observed in any of these tests. A 16 ft. diameter, concentrating solar dish was modified to accommodate the Sunexus CO2 Solar Reformer and the integrated system was installed at the Pacific Renewable Fuels and Chemicals test site at McClellan, CA. Several test runs were conducted without catalyst during which the ceramic heat exchanger in the Sunexus Solar Reformer reached temperatures between 1,050 F (566 C) and 2,200 F (1,204 C) during the test period. A dry reforming mixture of CO2/CH{sub 4} (2.0/1.0 molar ratio) was chosen for all of the tests on the integrated solar dish/catalytic reformer during December 2010. Initial tests were carried out to determine heat transfer from the collimated solar beam to the catalytic reactor. The catalyst was operated successfully at a steady-state temperature of 1,125 F (607 C), which was sufficient to convert 35% of the 2/1 CO2/CH{sub 4} mixture to syngas. This conversion efficiency confirmed the results from laboratory testing of this catalyst which provided comparable syngas production efficiencies (40% at 1,200 F [650 C]) with a resulting syngas composition of 20% CO, 16% H{sub 2}, 39% CO2 and 25% CH{sub 4}. As based upon the laboratory results, it is predicted that 90% of the CO2 will be converted to syngas in the solar reformer at 1,440 F (782 C) resulting in a syngas composition of 50% CO: 43% H{sub 2}: 7% CO2: 0% CH{sub 4}. Laboratory tests show that the higher catalyst operating temperature of 1,440 F (782 C) for efficient conversion of CO2 can certainly be achieved by optimizing solar reactor heat transfer, which would result in the projected 90% CO2-to-syngas conversion efficiencies. Further testing will be carried out during 2011, through other funding support, to further optimize the solar dish CO2 reformer. Additional studies carried out in support of this project and described in this report include: (1) An Assessment of Potential Contaminants in Captured CO2 from Various Industrial Processes and Their Possible Effect on Sunexus CO2 Reforming Catalysts; (2) Recommended Measurement Methods for Assessing Contaminant Levels in Captured CO2 Streams; (3) An Assessment of Current Commercial Scale Fisher-Tropsch (F-T) Technologies for the Conversion of Syngas to Fuels; (4) An Overview of CO2 Capture Technologies from Various Industrial Sources; and (5) Lifecycle Analysis for the Capture and Conversion of CO2 to Synthetic Diesel Fuel. Commercial scale Sunexus CO2 Solar Reformer plant designs, proposed in this report, should be able to utilize waste CO2 from a wide variety of industrial sources to produce a directly usable synthetic diesel fuel that replaces petroleum derived fuel, thus improving the United States energy security while also sequestering CO2. Our material balance model shows that every 5.0 lbs of CO2 is transformed using solar energy into 6.26 lbs (1.0 U.S. gallon) of diesel fuel and into by-products, which includes water. Details are provided in the mass and energy model in this report.« less

Self Consistent Bathymetric Mapping Using Sub-maps: Survey Results From the TAG Hydrothermal Structure

NASA Astrophysics Data System (ADS)

Roman, C. N.; Reves-Sohn, R.; Singh, H.; Humphris, S.

2005-12-01

The spatial resolution of microbathymetry maps created using robotic vehicles such as ROVs, AUVs and manned submersibles in the deep ocean is currently limited by the accuracy of the vehicle navigation data. Errors in the vehicle position estimate commonly exceed the ranging errors of the acoustic mapping sensor itself, which creates inconsistency in the map making process and produces artifacts that lower resolution and distort map integrity. We present a methodology for producing self-consistent maps and improving vehicle position estimation by exploiting accurate local navigation and utilizing terrain relative measurements. The complete map is broken down into individual "sub-maps'', which are generated using short term Doppler based navigation. The sub-maps are pairwise registered to constrain the vehicle position estimates by matching terrain that has been imaged multiple times. This procedure is implemented using a delayed state Kalman filter to incorporate the sub-map registrations as relative position measurements between previously visited vehicle locations. Archiving of previous positions in a filter state vector allows for continual adjustment of the sub-map locations. The terrain registration is accomplished using a two dimensional correlation and a six degree of freedom point cloud alignment method tailored to bathymetric data. This registration procedure is applicable to fully 3 dimensional complex underwater environments. The complete bathymetric map is then created from the union of all sub-maps that have been aligned in a consistent manner. The method is applied to an SM2000 multibeam survey of the TAG hydrothermal structure on the Mid-Atlantic Ridge at 26(°)N using the Jason II ROV. The survey included numerous crossing tracklines designed to test this algorithm, and the final gridded bathymetry data is sub-meter accurate. The high-resolution map has allowed for the identification of previously unrecognized fracture patterns associated with flow focusing at TAG, as well as imaging of fine-scale features such as individual sulfide talus blocks and ODP re-entry cones.

A stochastic perturbation method to generate inflow turbulence in large-eddy simulation models: Application to neutrally stratified atmospheric boundary layers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Muñoz-Esparza, D.; Kosović, B.; Beeck, J. van

2015-03-15

Despite the variety of existing methods, efficient generation of turbulent inflow conditions for large-eddy simulation (LES) models remains a challenging and active research area. Herein, we extend our previous research on the cell perturbation method, which uses a novel stochastic approach based upon finite amplitude perturbations of the potential temperature field applied within a region near the inflow boundaries of the LES domain [Muñoz-Esparza et al., “Bridging the transition from mesoscale to microscale turbulence in numerical weather prediction models,” Boundary-Layer Meteorol., 153, 409–440 (2014)]. The objective was twofold: (i) to identify the governing parameters of the method and their optimummore » values and (ii) to generalize the results over a broad range of atmospheric large-scale forcing conditions, U{sub g} = 5 − 25 m s{sup −1}, where U{sub g} is the geostrophic wind. We identified the perturbation Eckert number, Ec=U{sub g}{sup 2}/ρc{sub p}θ{sup ~}{sub pm}, to be the parameter governing the flow transition to turbulence in neutrally stratified boundary layers. Here, θ{sup ~}{sub pm} is the maximum perturbation amplitude applied, c{sub p} is the specific heat capacity at constant pressure, and ρ is the density. The optimal Eckert number was found for nonlinear perturbations allowed by Ec ≈ 0.16, which instigate formation of hairpin-like vortices that most rapidly transition to a developed turbulent state. Larger Ec numbers (linear small-amplitude perturbations) result in streaky structures requiring larger fetches to reach the quasi-equilibrium solution, while smaller Ec numbers lead to buoyancy dominated perturbations exhibiting difficulties for hairpin-like vortices to emerge. Cell perturbations with wavelengths within the inertial range of three-dimensional turbulence achieved identical quasi-equilibrium values of resolved turbulent kinetic energy, q, and Reynolds-shear stress, . In contrast, large-scale perturbations acting at the production range exhibited reduced levels of , due to the formation of coherent streamwise structures, while q was maintained, requiring larger fetches for the turbulent solution to stabilize. Additionally, the cell perturbation method was compared to a synthetic turbulence generator. The proposed stochastic approach provided at least the same efficiency in developing realistic turbulence, while accelerating the formation of large-scales associated with production of turbulent kinetic energy. Also, it is computationally inexpensive and does not require any turbulent information.« less

Sub-Scale Testing and Development of the J-2X Fuel Turbopump Inducer

NASA Technical Reports Server (NTRS)

Sargent, Scott R.; Becht, David G.

2011-01-01

In the early stages of the J-2X upper stage engine program, various inducer configurations proposed for use in the fuel turbopump (FTP) were tested in water. The primary objectives of this test effort were twofold. First, to obtain a more comprehensive data set than that which existed in the Pratt & Whitney Rocketdyne (PWR) historical archives from the original J-2S program, and second, to supplement that data set with information regarding the cavitation induced vibrations for both the historical J-2S configuration as well as those tested for the J-2X program. The J-2X FTP inducer, which actually consists of an inducer stage mechanically attached to a kicker stage, underwent 4 primary iterations utilizing sub-scaled test articles manufactured and tested in PWR's Engineering Development Laboratory (EDL). The kicker remained unchanged throughout the test series. The four inducer configurations tested retained many of the basic design features of the J-2S inducer, but also included variations on leading edge blade thickness and blade angle distribution, primarily aimed at improving suction performance at higher flow coefficients. From these data sets, the effects of the tested design variables on hydrodynamic performance and cavitation instabilities were discerned. A limited comparison of impact to the inducer efficiency was determined as well.

High-performance batteries for stationary energy storage and electric-vehicle propulsion. Progress report, October--December 1976. [Li--Al/LiCl--KCl/FeS or FeS/sub 2/, operate at 400 to 450 C

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nelson, P.A.; Yao, N.P.; Steunenberg, R.K.

1977-04-01

These batteries are being developed for electric vehicle propulsion and for stationary energy storage applications. The present battery cells, which operate at 400 to 450/sup 0/C, are of a vertically oriented, prismatic design with a central positive electrode of FeS or FeS/sub 2/, two facing negative electrodes of lithium--aluminum alloy, and an electrolyte of molten LiCl--KCl. Testing and evaluation of industrially fabricated cells is continuing. During this period, Li--Al/FeS and Li--Al/FeS/sub 2/ cells from Eagle-Picher Industries were tested, and tests of Li--Al/FeS cells from Gould Inc. were initiated. The cells are tested individually and in parallel and series battery configurations.more » These tests provide information on the effects of cell design modifications and alternative materials. Improved electrode and cell designs are being developed and tested at ANL, and the more promising designs are incorporated in the industrially fabricated cells. Among the concepts receiving major attention are carbon-bonded positive electrodes, scaled-up stationary energy storage cell designs, additives to extend electrode lifetime, and alternative electrode separators. The materials development efforts include the development of a new lightweight electrical feedthrough; investigations of new separator materials (e.g.,Y/sub 2/O/sub 3/ powder, Y/sub 2/O/sub 3/ felt, and porous, rigid ceramics); corrosion tests of materials for cell components; and postoperative examinations of cells. The cell chemistry studies were directed to discharge mechanisms of FeS electrodes, emf measurements of the LiAl/FeS/sub 2/ couple at various states of discharge, and studies of other transition-metal sulfides as positive-electrode materials. The advanced battery effort mainly concerned the use of calcium alloys for negative electrode and transition metal sulfides or oxides for the positive electrode. 13 figures, 18 tables.« less

Removal of Radionuclides from Waste Water at Fukushima Daiichi Nuclear Power Plant: Desalination and Adsorption Methods - 13126

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kani, Yuko; Kamosida, Mamoru; Watanabe, Daisuke

Waste water containing high levels of radionuclides due to the Fukushima Daiichi Nuclear Power Plant accident, has been treated by the adsorption removal and reverse-osmosis (RO) desalination to allow water re-use for cooling the reactors. Radionuclides in the waste water are collected in the adsorbent medium and the RO concentrate (RO brine) in the water treatment system currently operated at the Fukushima Daiichi site. In this paper, we have studied the behavior of radionuclides in the presently applied RO desalination system and the removal of radionuclides in possible additional adsorption systems for the Fukushima Daiichi waste water treatment. Regarding themore » RO desalination system, decontamination factors (DFs) of the elements present in the waste water were obtained by lab-scale testing using an RO unit and simulated waste water with non-radioactive elements. The results of the lab-scale testing using representative elements showed that the DF for each element depended on its hydrated ionic radius: the larger the hydrated ionic radius of the element, the higher its DF is. Thus, the DF of each element in the waste water could be estimated based on its hydrated ionic radius. For the adsorption system to remove radionuclides more effectively, we studied adsorption behavior of typical elements, such as radioactive cesium and strontium, by various kinds of adsorbents using batch and column testing. We used batch testing to measure distribution coefficients (K{sub d}s) for cesium and strontium onto adsorbents under different brine concentrations that simulated waste water conditions at the Fukushima Daiichi site. For cesium adsorbents, K{sub d}s with different dependency on the brine concentration were observed based on the mechanism of cesium adsorption. As for strontium, K{sub d}s decreased as the brine concentration increased for any adsorbents which adsorbed strontium by intercalation and by ion exchange. The adsorbent titanium oxide had higher K{sub d}s and it was used for the column testing to obtain breakthrough curves under various conditions of pH and brine concentration. The breakthrough point had a dependency on pH and the brine concentration. We found that when the pH was higher or the brine concentration was lower, the longer it took to reach the breakthrough point. The inhibition of strontium adsorption by alkali earth metals would be diminished for conditions of higher pH and lower brine concentration. (authors)« less

Application of Sub-Bottom Profiler to Study Riverbed Structure and Sediment Density

NASA Astrophysics Data System (ADS)

Rui, Wang; Changzheng, Li; Xiaofei, Yan

2018-03-01

In this pater, we present a study on the riverbed structure and sediment density in-situ test by using sub-bottom profiler. Compared with traditional direct observation methods, the sub-bottom profiler method based on sonar technology is non-contact, low-disturbance and high-efficient. We finish the investigation of several sections in Sanmenxia and Xiaolangdi reservoirs, which located on the main channel of lower reaches of Yellow River. Collected data show a detailed layered structure of the riverbed sediment which believed caused by sedimentary processes in different periods. Further more, we analyse the reflection coefficient of water-sediment interface and inverse the sediment density data from the raw wave record. The inversion method is based on the effective density fluid model and Kozeny-Carman formula. The comparison of the inversion results and sample tests shows that the in-situ test is reliable and useable.

Determination of effects of ambient conditions on aircraft engine emissions engine testing - GTCP 85 APU, TPE 331 turboprop. Volume 1. Final report 20 Dec 1974--20 Dec 1975

DOE Office of Scientific and Technical Information (OSTI.GOV)

Slogar, G.A.

1976-03-01

Full scale engine tests were conducted on a GTCP85-98CK Auxiliary Power Unit and a TPE331-5-251M Turboprop engine. The purpose of this program was to measure exhaust emission of HC, CO, CO/sub 2/, NO/sub x/, and smoke at controlled (temperature, humidity, and pressure) engine inlet conditions. This data along with other available data will provide the data base for the determination of the effects of ambient conditions on gas turbine engines. (GRA)

GRID-BASED EXPLORATION OF COSMOLOGICAL PARAMETER SPACE WITH SNAKE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mikkelsen, K.; Næss, S. K.; Eriksen, H. K., E-mail: kristin.mikkelsen@astro.uio.no

2013-11-10

We present a fully parallelized grid-based parameter estimation algorithm for investigating multidimensional likelihoods called Snake, and apply it to cosmological parameter estimation. The basic idea is to map out the likelihood grid-cell by grid-cell according to decreasing likelihood, and stop when a certain threshold has been reached. This approach improves vastly on the 'curse of dimensionality' problem plaguing standard grid-based parameter estimation simply by disregarding grid cells with negligible likelihood. The main advantages of this method compared to standard Metropolis-Hastings Markov Chain Monte Carlo methods include (1) trivial extraction of arbitrary conditional distributions; (2) direct access to Bayesian evidences; (3)more » better sampling of the tails of the distribution; and (4) nearly perfect parallelization scaling. The main disadvantage is, as in the case of brute-force grid-based evaluation, a dependency on the number of parameters, N{sub par}. One of the main goals of the present paper is to determine how large N{sub par} can be, while still maintaining reasonable computational efficiency; we find that N{sub par} = 12 is well within the capabilities of the method. The performance of the code is tested by comparing cosmological parameters estimated using Snake and the WMAP-7 data with those obtained using CosmoMC, the current standard code in the field. We find fully consistent results, with similar computational expenses, but shorter wall time due to the perfect parallelization scheme.« less

ED(MF)n: Humidity-Convection Feedbacks in a Mass Flux Scheme Based on Resolved Size Densities

NASA Astrophysics Data System (ADS)

Neggers, R.

2014-12-01

Cumulus cloud populations remain at least partially unresolved in present-day numerical simulations of global weather and climate, and accordingly their impact on the larger-scale flow has to be represented through parameterization. Various methods have been developed over the years, ranging in complexity from the early bulk models relying on a single plume to more recent approaches that attempt to reconstruct the underlying probability density functions, such as statistical schemes and multiple plume approaches. Most of these "classic" methods capture key aspects of cumulus cloud populations, and have been successfully implemented in operational weather and climate models. However, the ever finer discretizations of operational circulation models, driven by advances in the computational efficiency of supercomputers, is creating new problems for existing sub-grid schemes. Ideally, a sub-grid scheme should automatically adapt its impact on the resolved scales to the dimension of the grid-box within which it is supposed to act. It can be argued that this is only possible when i) the scheme is aware of the range of scales of the processes it represents, and ii) it can distinguish between contributions as a function of size. How to conceptually represent this knowledge of scale in existing parameterization schemes remains an open question that is actively researched. This study considers a relatively new class of models for sub-grid transport in which ideas from the field of population dynamics are merged with the concept of multi plume modelling. More precisely, a multiple mass flux framework for moist convective transport is formulated in which the ensemble of plumes is created in "size-space". It is argued that thus resolving the underlying size-densities creates opportunities for introducing scale-awareness and scale-adaptivity in the scheme. The behavior of an implementation of this framework in the Eddy Diffusivity Mass Flux (EDMF) model, named ED(MF)n, is examined for a standard case of subtropical marine shallow cumulus. We ask if a system of multiple independently resolved plumes is able to automatically create the vertical profile of bulk (mass) flux at which the sub-grid scale transport balances the imposed larger-scale forcings in the cloud layer.

Saudi normative data for the Wisconsin Card Sorting test, Stroop test, Test of Non-verbal Intelligence-3, Picture Completion and Vocabulary (subtest of the Wechsler Adult Intelligence Scale-Revised).

PubMed

Al-Ghatani, Ali M; Obonsawin, Marc C; Binshaig, Basmah A; Al-Moutaery, Khalaf R

2011-01-01

There are 2 aims for this study: first, to collect normative data for the Wisconsin Card Sorting Test (WCST), Stroop test, Test of Non-verbal Intelligence (TONI-3), Picture Completion (PC) and Vocabulary (VOC) sub-test of the Wechsler Adult Intelligence Scale-Revised for use in a Saudi Arabian culture, and second, to use the normative data provided to generate the regression equations. To collect the normative data and generate the regression equations, 198 healthy individuals were selected to provide a representative distribution for age, gender, years of education, and socioeconomic class. The WCST, Stroop test, TONI-3, PC, and VOC were administrated to the healthy individuals. This study was carried out at the Department of Clinical Neurosciences, Riyadh Military Hospital, Riyadh, Kingdom of Saudi Arabia from January 2000 to July 2002. Normative data were obtained for all tests, and tables were constructed to interpret scores for different age groups. Regression equations to predict performance on the 3 tests of frontal function from scores on tests of fluid (TONI-3) and premorbid intelligence were generated from the data from the healthy individuals. The data collected in this study provide normative tables for 3 tests of frontal lobe function and for tests of general intellectual ability for use in Saudi Arabia. The data also provide a method to estimate pre-injury ability without the use of verbally based tests.

Impact Testing and Analysis of Composites for Aircraft Engine Fan Cases

NASA Technical Reports Server (NTRS)

Roberts, Gary D.; Revilock, Duane M.; Binienda, Wieslaw K.; Nie, Walter Z.; Mackenzie, S. Ben; Todd, Kevin B.

2002-01-01

The fan case in a jet engine is a heavy structure because of its size and because of the requirement that it contain a blade released during engine operation. Composite materials offer the potential for reducing the weight of the case. Efficient design, test, and analysis methods are needed to efficiently evaluate the large number of potential composite materials and design concepts. The type of damage expected in a composite case under blade-out conditions was evaluated using a subscale test in which a glass/epoxy composite half-ring target was impacted with a wedge-shaped titanium projectile. Fiber shearing occurred near points of contact between the projectile and target. Delamination and tearing occurred on a larger scale. These damage modes were reproduced in a simpler test in which flat glass/epoxy composites were impacted with a blunt cylindrical projectile. A surface layer of ceramic eliminated fiber shear fracture but did not reduce delamination. Tests on 3D woven carbon/epoxy composites indicated that transverse reinforcement is effective in reducing delamination. A 91 cm (36 in.) diameter full-ring sub-component was proposed for larger scale testing of these and other composite concepts. Explicit, transient, finite element analyses indicated that a full-ring test is needed to simulate complete impact dynamics, but simpler tests using smaller ring sections are adequate when evaluation of initial impact damage is the primary concern.

The potential for political leadership in HIV/AIDS communication campaigns in Sub-Saharan Africa

PubMed Central

Karan, Abraar; Hartford, Emily; Coates, Thomas J.

2017-01-01

ABSTRACT Background: The HIV/AIDS epidemic has become a point of important political concern for governments especially in Sub-Saharan Africa. Clinical and public health interventions to curb the epidemic can be greatly enhanced with the strategic support of political leaders. Objective: We analyzed the role of national political leadership in large-scale HIV/AIDS communications campaigns in 14 countries in Sub-Saharan Africa. Methods: We primarily reviewed grey and white literature published from 2005–2014. We further triangulated data from in-person and phone interviews with key public health figures. Results: A number of themes emerged supporting political leaders’ efforts toward HIV/AIDS program improvement, including direct involvement of public officials in campaign spearheading, the acknowledgment of personal relationship to the HIV epidemic, and public testing and disclosure of HIV status. Areas for future improvement were also identified, including the need for more directed messaging, increased transparency both nationally and internationally and the reduction of stigmatizing messaging from leaders. Conclusions: The political system has a large role to play within the healthcare system, particularly for HIV/AIDS. This partnership between politics and the health must continue to strengthen and be leveraged to effect major change in behaviors and attitudes across Sub-Saharan Africa. PMID:28156196

Centeredness Theory: Understanding and Measuring Well-Being Across Core Life Domains

PubMed Central

Bloch-Jorgensen, Zephyr T.; Cilione, Patrick J.; Yeung, William W. H.; Gatt, Justine M.

2018-01-01

Background: Centeredness Theory (CT) is proposed as a new mental health paradigm that focuses on well-being at a systems-level, across the core life domains of the self, the family unit, relationships, community, and work. The current studies aimed to validate the psychometric properties of a new scale that measures CT against existing well-being and mental health measures. Methods: Study 1 included 488 anonymous online respondents (46% females, 28% males, 25% unknown with median age between 31 and 35 years) across 38 countries who completed the CT scale. Study 2 included 49 first-year psychology students (90% females, mean age of 19 years) from Sydney Australia that completed the CT scale and other well-being and mental health questionnaires at baseline and 2-weeks follow-up. Results: Exploratory and confirmatory factor analyses resulted in a refined 60-item CT scale with five domains, each with four sub-domains. The CT scale demonstrated good internal consistency reliability and test-retest reliability, and showed evidence of convergent validity against other well-being measures (e.g., COMPAS-W Wellbeing Scale, SWLS scale, and Ryff's Psychological Well-being scale). Conclusions: The CT scale appears to be a reliable measure of well-being at a systems-level. Future studies need to confirm these findings in larger heterogeneous samples. PMID:29765344

Approaching sub-50 nanoradian measurements by reducing the saw-tooth deviation of the autocollimator in the Nano-Optic-Measuring Machine

NASA Astrophysics Data System (ADS)

Qian, Shinan; Geckeler, Ralf D.; Just, Andreas; Idir, Mourad; Wu, Xuehui

2015-06-01

Since the development of the Nano-Optic-Measuring Machine (NOM), the accuracy of measuring the profile of an optical surface has been enhanced to the 100-nrad rms level or better. However, to update the accuracy of the NOM system to sub-50 nrad rms, the large saw-tooth deviation (269 nrad rms) of an existing electronic autocollimator, the Elcomat 3000/8, must be resolved. We carried out simulations to assess the saw-tooth-like deviation. We developed a method for setting readings to reduce the deviation to sub-50 nrad rms, suitable for testing plane mirrors. With this method, we found that all the tests conducted in a slowly rising section of the saw-tooth show a small deviation of 28.8 to <40 nrad rms. We also developed a dense-measurement method and an integer-period method to lower the saw-tooth deviation during tests of sphere mirrors. Further research is necessary for formulating a precise test for a spherical mirror. We present a series of test results from our experiments that verify the value of the improvements we made.

Downscaling catchment scale flood risk to contributing sub-catchments to determine the optimum location for flood management.

NASA Astrophysics Data System (ADS)

Pattison, Ian; Lane, Stuart; Hardy, Richard; Reaney, Sim

2010-05-01

The recent increase in flood frequency and magnitude has been hypothesised to have been caused by either climate change or land management. Field scale studies have found that changing land management practices does affect local runoff and streamflow, but upscaling these effects to the catchment scale continues to be problematic, both conceptually and more importantly methodologically. The impact on downstream flood risk is highly dependent upon where the changes are in the catchment, indicating that some areas of the catchment are more important in determining downstream flood risk than others. This is a major flaw in the traditional approach to studying the effect of land use on downstream flood risk: catchment scale hydrological models, which treat every cell in the model equally. We are proposing an alternative ideological approach for doing flood management research, which is underpinned by downscaling the downstream effect (problem i.e. flooding) to the upstream causes (contributing sub-catchments). It is hoped that this approach could have several benefits over the traditional upscaling approach. Firstly, it provides an efficient method to prioritise areas for land use management changes to be implemented to reduce downstream flood risk. Secondly, targets for sub-catchment hydrograph change can be determined which will deliver the required downstream effect. Thirdly, it may be possible to detect the effect of land use changes in upstream areas on downstream flood risk, by weighting the areas of most importance in hydrological models. Two methods for doing this downscaling are proposed; 1) data-based statistical analysis; and 2) hydraulic modelling-based downscaling. These will be outlined using the case study of the River Eden, Cumbria, NW England. The data-based methodology uses the timing and magnitude of floods for each sub-catchment. Principal components analysis (PCA) is used to simplify sub-catchment interactions and optimising stepwise regression is used to predict downstream flood magnitude from the significant principal components. Two particular sub-catchments, the Eamont and the Upper Eden were highlighted as explaining the highest proportion of downstream flood risk, with 21.0% and 19.6% respectively. This approach uses the concept of data mining, whereby commonly available discharge data is used in an innovative way to learn about catchment behaviour. An alternative downscaling approach is hydraulic modelling whereby the input hydrographs from each tributary are changed in turn, both in terms of the magnitudes and the timing of the flows. This basic scenario testing approach can be used to assess the sensitivity of downstream flood risk to upstream contributing tributaries. This approach also highlighted the Upper Eden and Eamont as the most sensitive sub-catchments. A 25% reduction in the flows from these sub-catchments resulted in a 33.1cm and 21.9cm stage reduction downstream respectively, while an 8 hour delay of the peak flow caused a 32.3cm and 27.4cm decrease in downstream stage respectively. This alternative flood management approach is not a replacement to traditional hydrological modelling (upscaling), but a pre-step which allows for more focussed and informed investigation of land management scenarios, in the area where they are most likely to have beneficial impacts on downstream flooding.

Modeling of the phase evolution in Mg1-xAlxB2 (0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andersson, Anders David; Casillas, Luis; Lezama Pacheco, Juan

Despite the chemical and structural simplicity of MgB{sub 2}, at 39 K this compound has the highest known {Tc} of any binary compound. Electron doping by substituting Al for Mg leads to decreasing Tc and the observed concentration dependent rate of decrease has been proposed to arise from the non-ideal character of MgB{sub 2}-AIB{sub 2} solid solutions, which derives from the existence of an ordered Mg{sub 0.5}Al{sub 0.5}B{sub 2} compound. Heterogeneous nano-scale structure patterns in solid solutions have emerged as an important concept for complex materials, ranging from actinide alloys and oxides to high-temperature cuprate superconductors and mallganite-based materials exhibitingmore » colossal magnetoresistivity. In this work we investigate the formation of structural heterogeneities in Mg{sub 1-x}AI{sub x}B{sub 2}, which take the form of nano-scale AI-AI and AI-Mg domains of different geometry and size, using molecular statics/dynamics simulations and in particular we study the corresponding signatures in diffraction experiments. In order to undertake this task we first derive appropriate Mg-AI-B semi-empirical potentials within the Modified Embedded Atom Method formalism. These potentials are also applied to explore the equilibrium Mg{sub 1-x}AI{sub x}B{sub 2} phase diagram for 0 < x < 0.5. Additionally, density functional theory calculations were utilized to study the influence of heterogeneities on the electronic structure and charge distribution in Mg{sub 1-x}AI{sub x}B{sub 2}.« less

Aqueous and gaseous nitrogen losses induced by fertilizer application

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gu, C.; Maggi, F.; Riley, W.J.

2009-01-15

In recent years concern has grown over the contribution of nitrogen (N) fertilizer use to nitrate (NO{sub 3}{sup -}) water pollution and nitrous oxide (N{sub 2}O), nitric oxide (NO), and ammonia (NH{sub 3}) atmospheric pollution. Characterizing soil N effluxes is essential in developing a strategy to mitigate N leaching and emissions to the atmosphere. In this paper, a previously described and tested mechanistic N cycle model (TOUGHREACT-N) was successfully tested against additional observations of soil pH and N{sub 2}O emissions after fertilization and irrigation, and before plant emergence. We used TOUGHREACT-N to explain the significantly different N gas emissions andmore » nitrate leaching rates resulting from the different N fertilizer types, application methods, and soil properties. The N{sub 2}O emissions from NH{sub 4}{sup +}-N fertilizer were higher than from urea and NO{sub 3}{sup -}-N fertilizers in coarse-textured soils. This difference increased with decreases in fertilization application rate and increases in soil buffering capacity. In contrast to methods used to estimate global terrestrial gas emissions, we found strongly non-linear N{sub 2}O emissions as a function of fertilizer application rate and soil calcite content. Speciation of predicted gas N flux into N{sub 2}O and N{sub 2} depended on pH, fertilizer form, and soil properties. Our results highlighted the need to derive emission and leaching factors that account for fertilizer type, application method, and soil properties.« less

Validation of laboratory-scale recycling test method of paper PSA label products

Treesearch

Carl Houtman; Karen Scallon; Richard Oldack

2008-01-01

Starting with test methods and a specification developed by the U.S. Postal Service (USPS) Environmentally Benign Pressure Sensitive Adhesive Postage Stamp Program, a laboratory-scale test method and a specification were developed and validated for pressure-sensitive adhesive labels, By comparing results from this new test method and pilot-scale tests, which have been...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hand, Nick; Seljak, Uroš; Li, Yin

Measurements of line-of-sight dependent clustering via the galaxy power spectrum's multipole moments constitute a powerful tool for testing theoretical models in large-scale structure. Recent work shows that this measurement, including a moving line-of-sight, can be accelerated using Fast Fourier Transforms (FFTs) by decomposing the Legendre polynomials into products of Cartesian vectors. Here, we present a faster, optimal means of using FFTs for this measurement. We avoid redundancy present in the Cartesian decomposition by using a spherical harmonic decomposition of the Legendre polynomials. With this method, a given multipole of order ℓ requires only 2ℓ+1 FFTs rather than the (ℓ+1)(ℓ+2)/2 FFTsmore » of the Cartesian approach. For the hexadecapole (ℓ = 4), this translates to 40% fewer FFTs, with increased savings for higher ℓ. The reduction in wall-clock time enables the calculation of finely-binned wedges in P ( k ,μ), obtained by computing multipoles up to a large ℓ{sub max} and combining them. This transformation has a number of advantages. We demonstrate that by using non-uniform bins in μ, we can isolate plane-of-sky (angular) systematics to a narrow bin at 0μ ≅ while eliminating the contamination from all other bins. We also show that the covariance matrix of clustering wedges binned uniformly in μ becomes ill-conditioned when combining multipoles up to large values of ℓ{sub max}, but that the problem can be avoided with non-uniform binning. As an example, we present results using ℓ{sub max}=16, for which our procedure requires a factor of 3.4 fewer FFTs than the Cartesian method, while removing the first μ bin leads only to a 7% increase in statistical error on f σ{sub 8}, as compared to a 54% increase with ℓ{sub max}=4.« less

Inflight Exercise Regimen for the 2-Hour Prebreathe Protocol

NASA Technical Reports Server (NTRS)

Foster, Philip P.; Gernhardt, Michael L.; Woodruff, Kristin K.; Schneider, Susan M.; Homick, Jerry L. (Technical Monitor)

2000-01-01

A 10 min aerobic prebreathe exercise up to 75% V-O2(sub max) on a dual-cycle ergometer, included in the 2-hour prebreathe protocol, has been shown to dramatically reduce the incidence of decompression sickness (DCS) at altitude. In-flight only leg ergometry will be available. A balanced exercise was developed using surgical tubing with the ergometer on-orbit. We hypothesize that a 75% V02max workload, individually prescribed, would be achieved using a target heart rate to regulate the intensity of the arm exercise. VO2, heart rate (HR) / ECG, V-CO2 /V-O2, V(sub E), and V(sub T), and rate of perceived exertion (Borg scale) were measured in eleven healthy subjects who passed a US Air Force Class III Physical examination. A V-O2 peak test was performed to assess the sub-maximal exercise prescription. Two series of sub-maximal tests were performed: (1) leg ergometer/hand ergometer and (2) leg ergometer/surgical tubes. We found no significant differences (P > 0.05) in comparing the means for V-O2 and HR between the predicted and measured values during the final 4 minute-stage at "75% V-O2 workload" or between the two types of sub-maximal tests. The prescribed prebreathe sub-maximal exercise performed with flight certified surgical tubes was achieved using the target HR.

HOW UNIVERSAL IS THE {Sigma}{sub SFR}-{Sigma}{sub H{sub 2}} RELATION?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feldmann, R.; Gnedin, N. Y.; Kravtsov, A. V., E-mail: feldmann@fnal.gov

It is a well-established empirical fact that the surface density of the star formation rate, {Sigma}{sub SFR}, strongly correlates with the surface density of molecular hydrogen, {Sigma}{sub H{sub 2}}, at least when averaged over large ({approx}kpc) scales. Much less is known, however, about whether (and how) the {Sigma}{sub SFR}-{Sigma}{sub H{sub 2}} relation depends on environmental parameters, such as the metallicity or the UV radiation field in the interstellar medium (ISM). Furthermore, observations indicate that the scatter in the {Sigma}{sub SFR}-{Sigma}{sub H{sub 2}} relation increases rapidly with decreasing averaging scale. How the scale-dependent scatter is generated and how one recovers amore » tight {approx} kpc scale {Sigma}{sub SFR}-{Sigma}{sub 2} relation in the first place is still largely debated. Here, these questions are explored with hydrodynamical simulations that follow the formation and destruction of H{sub 2}, include radiative transfer of UV radiation, and resolve the ISM on {approx}60 pc scales. We find that within the considered range of H{sub 2} surface densities (10-100 M{sub sun} pc{sup -2}), the {Sigma}{sub SFR}-{Sigma}{sub H{sub 2}} relation is steeper in environments of low-metallicity and/or high-radiation fields (compared to the Galaxy), that the star formation rate (SFR) at a given H{sub 2} surface density is larger, and the scatter is increased. Deviations from a 'universal' {Sigma}{sub SFR}-{Sigma}{sub H{sub 2}} relation should be particularly relevant for high-redshift galaxies or for low-metallicity dwarfs at z {approx} 0. We also find that the use of time-averaged SFRs produces a large, scale-dependent scatter in the {Sigma}{sub SFR}-{Sigma}{sub H{sub 2}} relation. Given the plethora of observational data expected from upcoming surveys such as ALMA, the scale-scatter relation may indeed become a valuable tool for determining the physical mechanisms connecting star formation and H{sub 2} formation.« less

Assessment of the psychometric properties of the Spanish language version of questionnaire ICIQ-Male Lower Urinary Tract Symptoms (ICIQ-MLUTS).

PubMed

Castro-Díaz, D M; Esteban-Fuertes, M; Salinas-Casado, J; Bustamante-Alarma, S; Gago-Ramos, J L; Galacho-Bech, A; García-Matres, M J; Rodríguez-Toves, L A; Zubiaur-Líbano, C; Collado-Serra, A; Batista-Miranda, J E; Ortiz-Gámiz, A

2014-03-01

To evaluate the psychometric properties of the Spanish version of the ICIQ-Male Lower Urinary Tract Symptoms Questionnaire (ICIQ-MLUTS): Feasibility (% of completion and ceiling/ground effects), reliability (Test-retest), convergent validity (vs Bladder Control Self-Assessment Questionnaire [BSAQ] and vs International Prostate Symptom Score [I-PSS]) and criterion validity (according to presence or absence of symptoms). This was an observational, non-interventionist and multicenter study. 223 male patients with lower urinary tract symptoms (LUTS), predominantly storage symptoms and aged 18-65, took part in the study. Patients completed the ICIQ-MLUTS (test), I-PSS and BSAQ questionnaires and referred their urinary symptoms in a single visit, with the exception of a subgroup composed by 49 patients that completed the questionnaire again 15 days after initial visit to evaluate test-retest reliability. The questionnaire includes 13 items divided in 2 sub-scales: Voiding symptoms (V) from 0-20 and Incontinence symptoms (I) from 0-24. Percentage of patients that completed all items: 98.84%. Ground effect is 0 and ceiling effect was under 6% in both sub-scales. Test-retest reliability: Intraclass correlation coefficient (ICC) ranged from 0.68 to 0.88, except on Delay. Kappa shows a good agreement, between 0.60 and 0.81, except for Nocturia. Convergent validity: Correlation (Spearman) between the questionnaire sub-scales scores and the rest of measures is statistically significant (P < .01 and P < .05). Criterion validity: Statistically significant differences (P < .05) between scores on ICIQ-MLUTS, from patients that refer experiencing symptoms and those who do not. The Spanish version of the ICIQ-MLUTS questionnaire shows adequate feasibility, reliability and validity. Copyright © 2013 AEU. Published by Elsevier Espana. All rights reserved.

Training Students to Analyze Spatial and Temporal Heterogeneities in Reservoir and Seal Petrology, Mineralogy, and Geochemistry: Implications for CO{sub 2} Sequestration Prediction, Simulation, and Monitoring

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bowen, Brenda

The objective of this project was to expose and train multiple students in geological tools that are essential to reservoir characterization and geologic sequestration including but not limited to advanced petrological methods, mineralogical methods, and geochemical methods; core analysis, and geophysical well-log interpretation. These efforts have included training of multiple students through geologically based curriculum and research using advanced petrological, mineralogical, and geochemical methods. In whole, over the last 3+ years, this award has supported 5,828 hours of student research, supporting the work of several graduate and undergraduate students. They have all received training directly related to ongoing CO{sub 2}more » sequestration demonstrations. The students have all conducted original scientific research on topics related to understanding the importance of lithological, textural, and compositional variability in formations that are being targeted as CO{sub 2} sequestration reservoirs and seals. This research was linked to the Mount Simon Sandstone reservoir and overlying Eau Claire Formation seal in the Illinois Basin- a system where over one million tons of CO{sub 2} are actively being injected with the first large-scale demonstration of anthropogenic CO{sub 2} storage in the U.S. Student projects focused specifically on 1) reservoir porosity characterization and evaluation, 2) petrographic, mineralogical, and geochemical evidence of fluid-related diagenesis in the caprock, 3) textural changes in reservoir samples exposed to experimental CO{sub 2} + brine conditions, 4) controls on spatial heterogeneity in composition and texture in both the reservoir and seal, 5) the implications of small-scale fractures within the reservoir, and 6) petrographic and stable isotope analyses of carbonates in the seal to understand the burial history of the system. The student-led research associated with this project provided real-time and hands-on experience with a relevant CO{sub 2} system, provided relevant information to the regional partnerships who are working within these formations, and provides more broadly applicable understanding and method development for other carbon capture and storage systems.« less

Bayesian model for matching the radiometric measurements of aerospace and field ocean color sensors.

PubMed

Salama, Mhd Suhyb; Su, Zhongbo

2010-01-01

A Bayesian model is developed to match aerospace ocean color observation to field measurements and derive the spatial variability of match-up sites. The performance of the model is tested against populations of synthesized spectra and full and reduced resolutions of MERIS data. The model derived the scale difference between synthesized satellite pixel and point measurements with R(2) > 0.88 and relative error < 21% in the spectral range from 400 nm to 695 nm. The sub-pixel variabilities of reduced resolution MERIS image are derived with less than 12% of relative errors in heterogeneous region. The method is generic and applicable to different sensors.

NASA High-Speed 2D Photogrammetric Measurement System

NASA Technical Reports Server (NTRS)

Dismond, Harriett R.

2012-01-01

The object of this report is to provide users of the NASA high-speed 2D photogrammetric measurement system with procedures required to obtain drop-model trajectory and impact data for full-scale and sub-scale models. This guide focuses on use of the system for vertical drop testing at the NASA Langley Landing and Impact Research (LandIR) Facility.

A bioequivalence study of two memantine formulations in healthy Chinese male volunteers
.

PubMed

Deng, Ying; Zhuang, Jialang; Wu, Jingguo; Chen, Jiangying; Ding, Liang; Wang, Xueding; Huang, Lihui; Zeng, Guixiong; Chen, Jie; Ma, Zhongfu; Chen, Xiao; Zhong, Guoping; Huang, Min; Zhao, Xianglan

2017-10-01

The aim of the current study is to evaluate the bioequivalence between the test and reference formulations of memantine in a single-dose, two-period and two-sequence crossover study with a 44-day washout interval. A total of 20 healthy Chinese male volunteers were enrolled and completed the study, after oral administration of single doses of 10 mg test and reference formulations of memantine. The blood samples were collected at different time points and memantine concentrations were determined by a fully validated HPLC-MS/MS method. The evaluated pharmacokinetic parameters (test vs. reference) including C_max (18 ± 3.2 vs. 17.8 ± 3.4), AUC_0-t (1,188.5 ± 222.2 vs. 1,170.9 ± 135.7), and AUC_0-∞ (1,353.3 ± 258.6 vs. 1,291.3 ± 136.7) values were assessed for bioequivalence based on current guidelines. The observed pharmacokinetic parameters of memantine test drug were similar to those of the reference formulation. The 90% confidence intervals of test/reference ratios for C_max, AUC_0-t, and AUC_0-∞ were within the bioequivalence acceptance range of 80 - 125%. The results obtained from the healthy Chinese subjects in this study suggests that the test formulation of memantine 10 mg tablet is bioequivalent to the reference formulation (Ebixa^®10 mg tablet).
.

Full-Coverage High-Resolution Daily PM(sub 2.5) Estimation using MAIAC AOD in the Yangtze River Delta of China

NASA Technical Reports Server (NTRS)

Xiao, Qingyang; Wang, Yujie; Chang, Howard H.; Meng, Xia; Geng, Guannan; Lyapustin, Alexei Ivanovich; Liu, Yang

2017-01-01

Satellite aerosol optical depth (AOD) has been used to assess population exposure to fine particulate matter (PM (sub 2.5)). The emerging high-resolution satellite aerosol product, Multi-Angle Implementation of Atmospheric Correction(MAIAC), provides a valuable opportunity to characterize local-scale PM(sub 2.5) at 1-km resolution. However, non-random missing AOD due to cloud snow cover or high surface reflectance makes this task challenging. Previous studies filled the data gap by spatially interpolating neighboring PM(sub 2.5) measurements or predictions. This strategy ignored the effect of cloud cover on aerosol loadings and has been shown to exhibit poor performance when monitoring stations are sparse or when there is seasonal large-scale missngness. Using the Yangtze River Delta of China as an example, we present a Multiple Imputation (MI) method that combines the MAIAC high-resolution satellite retrievals with chemical transport model (CTM) simulations to fill missing AOD. A two-stage statistical model driven by gap-filled AOD, meteorology and land use information was then fitted to estimate daily ground PM(sub 2.5) concentrations in 2013 and 2014 at 1 km resolution with complete coverage in space and time. The daily MI models have an average R(exp 2) of 0.77, with an inter-quartile range of 0.71 to 0.82 across days. The overall Ml model 10-fold cross-validation R(exp 2) (root mean square error) were 0.81 (25 gm(exp 3)) and 0.73 (18 gm(exp 3)) for year 2013 and 2014, respectively. Predictions with only observational AOD or only imputed AOD showed similar accuracy.Comparing with previous gap-filling methods, our MI method presented in this study performed bette rwith higher coverage, higher accuracy, and the ability to fill missing PM(sub 2.5) predictions without ground PM(sub 2.5) measurements. This method can provide reliable PM(sub 2.5)predictions with complete coverage that can reduce biasin exposure assessment in air pollution and health studies.

Evaluation of Alternative Altitude Scaling Methods for Thermal Ice Protection System in NASA Icing Research Tunnel

NASA Technical Reports Server (NTRS)

Lee, Sam; Addy, Harold E. Jr.; Broeren, Andy P.; Orchard, David M.

2017-01-01

A test was conducted at NASA Icing Research Tunnel to evaluate altitude scaling methods for thermal ice protection system. Two new scaling methods based on Weber number were compared against a method based on Reynolds number. The results generally agreed with the previous set of tests conducted in NRCC Altitude Icing Wind Tunnel where the three methods of scaling were also tested and compared along with reference (altitude) icing conditions. In those tests, the Weber number-based scaling methods yielded results much closer to those observed at the reference icing conditions than the Reynolds number-based icing conditions. The test in the NASA IRT used a much larger, asymmetric airfoil with an ice protection system that more closely resembled designs used in commercial aircraft. Following the trends observed during the AIWT tests, the Weber number based scaling methods resulted in smaller runback ice than the Reynolds number based scaling, and the ice formed farther upstream. The results show that the new Weber number based scaling methods, particularly the Weber number with water loading scaling, continue to show promise for ice protection system development and evaluation in atmospheric icing tunnels.

Epidemiological Study of Mild Tramautic Brain Injury Sequelae Cause by Blast Exposure During Operations Iraqi Freedom and Enduring Freedom

DTIC Science & Technology

2012-10-01

Principal Investigator September, 2008 20 (see: VCU sub- award) David X. Cifu, MD Co-Investigator September, 2008 5 (VCU sub-award) Jessica...proven reliability: Wechsler Test of Adult Reading (WTAR, pre- morbid IQ estimate),(Mathias, Bowden, Bigler, & Rosenfeld, 2007) Conners Continuous...II (CVLT-II) (learning and working memory),(Vanderploeg et al., 2005) Wechsler Adult Intelligence Scale III (WAIS-III) items: Digit Symbol Coding

Continuous improvement of medical test reliability using reference methods and matrix-corrected target values in proficiency testing schemes: application to glucose assay.

PubMed

Delatour, Vincent; Lalere, Beatrice; Saint-Albin, Karène; Peignaux, Maryline; Hattchouel, Jean-Marc; Dumont, Gilles; De Graeve, Jacques; Vaslin-Reimann, Sophie; Gillery, Philippe

2012-11-20

The reliability of biological tests is a major issue for patient care in terms of public health that involves high economic stakes. Reference methods, as well as regular external quality assessment schemes (EQAS), are needed to monitor the analytical performance of field methods. However, control material commutability is a major concern to assess method accuracy. To overcome material non-commutability, we investigated the possibility of using lyophilized serum samples together with a limited number of frozen serum samples to assign matrix-corrected target values, taking the example of glucose assays. Trueness of the current glucose assays was first measured against a primary reference method by using human frozen sera. Methods using hexokinase and glucose oxidase with spectroreflectometric detection proved very accurate, with bias ranging between -2.2% and +2.3%. Bias of methods using glucose oxidase with spectrophotometric detection was +4.5%. Matrix-related bias of the lyophilized materials was then determined and ranged from +2.5% to -14.4%. Matrix-corrected target values were assigned and used to assess trueness of 22 sub-peer groups. We demonstrated that matrix-corrected target values can be a valuable tool to assess field method accuracy in large scale surveys where commutable materials are not available in sufficient amount with acceptable costs. Copyright © 2012 Elsevier B.V. All rights reserved.

Modelling of Sub-daily Hydrological Processes Using Daily Time-Step Models: A Distribution Function Approach to Temporal Scaling

NASA Astrophysics Data System (ADS)

Kandel, D. D.; Western, A. W.; Grayson, R. B.

2004-12-01

Mismatches in scale between the fundamental processes, the model and supporting data are a major limitation in hydrologic modelling. Surface runoff generation via infiltration excess and the process of soil erosion are fundamentally short time-scale phenomena and their average behaviour is mostly determined by the short time-scale peak intensities of rainfall. Ideally, these processes should be simulated using time-steps of the order of minutes to appropriately resolve the effect of rainfall intensity variations. However, sub-daily data support is often inadequate and the processes are usually simulated by calibrating daily (or even coarser) time-step models. Generally process descriptions are not modified but rather effective parameter values are used to account for the effect of temporal lumping, assuming that the effect of the scale mismatch can be counterbalanced by tuning the parameter values at the model time-step of interest. Often this results in parameter values that are difficult to interpret physically. A similar approach is often taken spatially. This is problematic as these processes generally operate or interact non-linearly. This indicates a need for better techniques to simulate sub-daily processes using daily time-step models while still using widely available daily information. A new method applicable to many rainfall-runoff-erosion models is presented. The method is based on temporal scaling using statistical distributions of rainfall intensity to represent sub-daily intensity variations in a daily time-step model. This allows the effect of short time-scale nonlinear processes to be captured while modelling at a daily time-step, which is often attractive due to the wide availability of daily forcing data. The approach relies on characterising the rainfall intensity variation within a day using a cumulative distribution function (cdf). This cdf is then modified by various linear and nonlinear processes typically represented in hydrological and erosion models. The statistical description of sub-daily variability is thus propagated through the model, allowing the effects of variability to be captured in the simulations. This results in cdfs of various fluxes, the integration of which over a day gives respective daily totals. Using 42-plot-years of surface runoff and soil erosion data from field studies in different environments from Australia and Nepal, simulation results from this cdf approach are compared with the sub-hourly (2-minute for Nepal and 6-minute for Australia) and daily models having similar process descriptions. Significant improvements in the simulation of surface runoff and erosion are achieved, compared with a daily model that uses average daily rainfall intensities. The cdf model compares well with a sub-hourly time-step model. This suggests that the approach captures the important effects of sub-daily variability while utilizing commonly available daily information. It is also found that the model parameters are more robustly defined using the cdf approach compared with the effective values obtained at the daily scale. This suggests that the cdf approach may offer improved model transferability spatially (to other areas) and temporally (to other periods).

Reviewing independent access to HIV testing, counselling and treatment for adolescents in HIV-specific laws in sub-Saharan Africa: implications for the HIV response

PubMed Central

Eba, Patrick M.; Lim, HyeYoung

2017-01-01

Abstract Introduction: AIDS is a leading cause of death among adolescents in sub-Saharan Africa. Yet, legal, policy and social barriers continue to restrict their access to HIV services. In recent years, access to independent HIV testing and treatment for adolescents has gained increased attention. The 2013 WHO Guidance on HIV testing and counselling and care for adolescents living with HIV (WHO Guidance) calls for reviewing legal and regulatory frameworks to facilitate adolescents’ access to comprehensive HIV services. As of 31 March 2017, some 28 countries in sub-Saharan Africa have adopted HIV-specific legislation. But there is limited understanding of the provisions of these laws on access to HIV services for adolescents and their implication on efforts to scale up HIV prevention, testing, treatment and care among this population. Methods: A desk review of 28 HIV-specific laws in sub-Saharan Africa complemented with the review of HIV testing policies in four countries using human rights norms and key public health recommendations from the 2013 WHO Guidance. These recommendations call on countries to (i) lower the age of consent to HIV testing and counselling and allow mature adolescents who have not reached the age of consent to independently access HIV testing, (ii) ensure access to HIV counselling for adolescents, (iii) protect the confidentiality of adolescents living with HIV and (iv) facilitate access to HIV treatment for adolescents living with HIV. Results: Most HIV-specific laws fail to take into account human rights principles and public health recommendations for facilitating adolescents’ access to HIV services. None of the countries with HIV-specific laws has adopted all four recommendations for access to HIV services for adolescents. Discrepancies exist between HIV laws and national policy documents. Inadequate and conflicting provisions in HIV laws are likely to hinder access to HIV testing, counselling and treatment for adolescents. Conclusions: Efforts to end legal barriers to access to HIV services for adolescents in sub-Saharan Africa should address HIV-specific laws. Restrictive provisions in these laws should be reformed, and their protective norms effectively implemented including by translating them into national policies and ensuring sensitization and training of healthcare workers and communities. This study reiterates the need for action in all countries across Africa and beyond to review their laws and policies to create an enabling environment to accelerate access to HIV prevention, testing and treatment services for adolescents. PMID:28799324

Polymer physics of chromosome large-scale 3D organisation

NASA Astrophysics Data System (ADS)

Chiariello, Andrea M.; Annunziatella, Carlo; Bianco, Simona; Esposito, Andrea; Nicodemi, Mario

2016-07-01

Chromosomes have a complex architecture in the cell nucleus, which serves vital functional purposes, yet its structure and folding mechanisms remain still incompletely understood. Here we show that genome-wide chromatin architecture data, as mapped by Hi-C methods across mammalian cell types and chromosomes, are well described by classical scaling concepts of polymer physics, from the sub-Mb to chromosomal scales. Chromatin is a complex mixture of different regions, folded in the conformational classes predicted by polymer thermodynamics. The contact matrix of the Sox9 locus, a region linked to severe human congenital diseases, is derived with high accuracy in mESCs and its molecular determinants identified by the theory; Sox9 self-assembles hierarchically in higher-order domains, involving abundant many-body contacts. Our approach is also applied to the Bmp7 locus. Finally, the model predictions on the effects of mutations on folding are tested against available data on a deletion in the Xist locus. Our results can help progressing new diagnostic tools for diseases linked to chromatin misfolding.

Women's views on consent, counseling and confidentiality in PMTCT: a mixed-methods study in four African countries.

PubMed

Hardon, Anita; Vernooij, Eva; Bongololo-Mbera, Grace; Cherutich, Peter; Desclaux, Alice; Kyaddondo, David; Ky-Zerbo, Odette; Neuman, Melissa; Wanyenze, Rhoda; Obermeyer, Carla

2012-01-11

Ambitious UN goals to reduce the mother-to-child transmission of HIV have not been met in much of Sub-Saharan Africa. This paper focuses on the quality of information provision and counseling and disclosure patterns in Burkina Faso, Kenya, Malawi and Uganda to identify how services can be improved to enable better PMTCT outcomes. Our mixed-methods study draws on data obtained through: (1) the MATCH (Multi-country African Testing and Counseling for HIV) study's main survey, conducted in 2008-09 among clients (N = 408) and providers at health facilities offering HIV Testing and Counseling (HTC) services; 2) semi-structured interviews with a sub-set of 63 HIV-positive women on their experiences of stigma, disclosure, post-test counseling and access to follow-up psycho-social support; (3) in-depth interviews with key informants and PMTCT healthcare workers; and (4) document study of national PMTCT policies and guidelines. We quantitatively examined differences in the quality of counseling by country and by HIV status using Fisher's exact tests. The majority of pregnant women attending antenatal care (80-90%) report that they were explained the meaning of the tests, explained how HIV can be transmitted, given advice on prevention, encouraged to refer their partners for testing, and given time to ask questions. Our qualitative findings reveal that some women found testing regimes to be coercive, while disclosure remains highly problematic. 79% of HIV-positive pregnant women reported that they generally keep their status secret; only 37% had disclosed to their husband. To achieve better PMTCT outcomes, the strategy of testing women in antenatal care (perceived as an exclusively female domain) when they are already pregnant needs to be rethought. When scaling up HIV testing programs, it is particularly important that issues of partner disclosure are taken seriously.

CHARACTERIZATION OF TANK 16H ANNULUS SAMPLES PART II: LEACHING RESULTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hay, M.; Reboul, S.

2012-06-19

The closure of Tank 16H will require removal of material from the annulus of the tank. Samples from Tank 16H annulus were characterized and tested to provide information to evaluate various alternatives for removing the annulus waste. The analysis found all four annulus samples to be composed mainly of Si, Na, and Al and lesser amounts of other elements. The XRD data indicate quartz (SiO{sub 2}) and sodium aluminum nitrate silicate hydrate (Na{sub 8}(Al{sub 6}Si{sub 6}O{sub 24})(NO{sub 3}){sub 2}.4H{sub 2}O) as the predominant crystalline mineral phases in the samples. The XRD data also indicate the presence of crystalline sodium nitratemore » (NaNO{sub 3}), sodium nitrite (NaNO{sub 2}), gibbsite (Al(OH){sub 3}), hydrated sodium bicarbonate (Na{sub 3}H(CO{sub 3}){sub 2}.2H{sub 2}O), and muscovite (KAl{sub 2}(AlSi{sub 3}O{sub 10})(OH){sub 2}). Based on the weight of solids remaining at the end of the test, the water leaching test results indicate 20-35% of the solids dissolved after three contacts with an approximately 3:1 volume of water at 45 C. The chemical analysis of the leachates and the XRD results of the remaining solids indicate sodium salts of nitrate, nitrite, sulfate, and possibly carbonate/bicarbonate make up the majority of the dissolved material. The majority of these salts were dissolved in the first water contact and simply diluted with each subsequent water contact. The water leaching removed large amounts of the uranium in two of the samples and approximately 1/3 of the {sup 99}Tc from all four samples. Most of the other radionuclides analyzed showed low solubility in the water leaching test. The oxalic acid leaching test result indicate approximately 34-47% of the solids in the four annulus samples will dissolve after three contacts with an approximately 3:1 volume of acid to solids at 45 C. The same sodium salts found in the water leaching test comprise the majority of dissolved material in the oxalic acid leaching test. However, the oxalic acid was somewhat more effective in dissolving radionuclides than the water leach. In contrast to the water leaching results, most constituents continued to dissolve during subsequent cycles of oxalic acid leaching. The somewhat higher dissolution found in the oxalic acid leaching test versus the water leaching test might be offset by the tendency of the oxalic acid solutions to take on a gel-like consistency. The filtered solids left behind after three oxalic acid contacts were sticky and formed large clumps after drying. These two observations could indicate potential processing difficulties with solutions and solids from oxalic acid leaching. The gel formation might be avoided by using larger volumes of the acid. Further testing would be recommended before using oxalic acid to dissolve the Tank 16H annulus waste to ensure no processing difficulties are encountered in the full scale process.« less

Effect of aromatherapy via inhalation on the sleep quality and fatigue level in people undergoing hemodialysis.

PubMed

Muz, Gamze; Taşcı, Sultan

2017-10-01

The most common problems in hemodialysis patients are sleep disorders and fatigue. This randomized-controlled experimental study was conducted to determine the effect of aromatherapy applied by inhalation on sleep quality and fatigue level in hemodialysis patients. The study was completed in five hemodialysis centers settled in two provinces with 27 intervention group patients and 35 controls, being totally 62 patients, recruited with simple randomization. Ethical approval, informed consent from the individuals and institutional permission were obtained. Data were collected with a questionnaire form and Visual Analogue Scale (VAS) for fatigue, Piper fatigue scale, Pittsburgh Sleep Quality Index (PSQI), and follow-up forms for the patient and the researcher. Aromatherapy inhalation (sweet orange and lavender oil) was performed before going to bed every day for one month to the intervention group patients. No other application has been made to the control group patients except for standard hemodialysis treatment. All of the forms were performed at baseline and at follow-up at the end of the four weeks (baseline and last follow-up), VAS and Piper fatigue scale were performed during follow-ups at the end of every week (the first, second and third follow-ups). Data were statistically analyzed with Independent Samples t-test, one way analysis of variance, Pearson correlation analysis, chi-square test, Friedman and Mann Whitney U tests and Bonferroni test. p<0.05 was set as statistically significant in comparisons. Mean total and sub-dimension scores of VAS, Piper fatigue scale and PSQI (except for daytime sleepiness dysfunction sub-dimension) of the intervention and control groups at baseline were not significantly different (p>0.05). It was found that mean total and sub-dimension scores of VAS, Piper fatigue scale and PSQI of the intervention group significantly decreased in other follow-ups compared to the control group (p<0.05). Consequently, it was determined that aromatherapy applied by inhalation improved sleep quality, decreased fatigue level and severity in hemodialysis patients. Accordingly, aromatherapy prepared with sweet orange and lavender oil may be recommended to increase sleep quality and to decrease fatigue level of the hemodialysis patients. Copyright © 2017 Elsevier Inc. All rights reserved.

Flexible sampling large-scale social networks by self-adjustable random walk

NASA Astrophysics Data System (ADS)

Xu, Xiao-Ke; Zhu, Jonathan J. H.

2016-12-01

Online social networks (OSNs) have become an increasingly attractive gold mine for academic and commercial researchers. However, research on OSNs faces a number of difficult challenges. One bottleneck lies in the massive quantity and often unavailability of OSN population data. Sampling perhaps becomes the only feasible solution to the problems. How to draw samples that can represent the underlying OSNs has remained a formidable task because of a number of conceptual and methodological reasons. Especially, most of the empirically-driven studies on network sampling are confined to simulated data or sub-graph data, which are fundamentally different from real and complete-graph OSNs. In the current study, we propose a flexible sampling method, called Self-Adjustable Random Walk (SARW), and test it against with the population data of a real large-scale OSN. We evaluate the strengths of the sampling method in comparison with four prevailing methods, including uniform, breadth-first search (BFS), random walk (RW), and revised RW (i.e., MHRW) sampling. We try to mix both induced-edge and external-edge information of sampled nodes together in the same sampling process. Our results show that the SARW sampling method has been able to generate unbiased samples of OSNs with maximal precision and minimal cost. The study is helpful for the practice of OSN research by providing a highly needed sampling tools, for the methodological development of large-scale network sampling by comparative evaluations of existing sampling methods, and for the theoretical understanding of human networks by highlighting discrepancies and contradictions between existing knowledge/assumptions of large-scale real OSN data.

Characterization of Oxy-combustion Impacts in Existing Coal-fired Boilers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adams, Bradley; Davis, Kevin; Senior, Constance

Reaction Engineering International (REI) managed a team of experts from University of Utah, Siemens Energy, Praxair, Vattenfall AB, Sandia National Laboratories, Brigham Young University (BYU) and Corrosion Management Ltd. to perform multi-scale experiments, coupled with mechanism development, process modeling and CFD modeling, for both applied and fundamental investigations. The primary objective of this program was to acquire data and develop tools to characterize and predict impacts of CO{sub 2} flue gas recycle and burner feed design on flame characteristics (burnout, NO{sub x}, SO{sub x}, mercury and fine particle emissions, heat transfer) and operational concerns (fouling, slagging and corrosion) inherent inmore » the retrofit of existing coal-fired boilers for oxy-coal combustion. Experimental work was conducted at Sandia National Laboratories’ Entrained Flow Reactor, the University of Utah Industrial Combustion Research Facility, and Brigham Young University. Process modeling and computational fluid dynamics (CFD) modeling was performed at REI. Successful completion of the project objectives resulted in the following key deliverables: 1) Multi-scale test data from 0.1 kW bench-scale, 100 kW and 200 kW laboratory-scale, and 1 MW semi-industrial scale combustors that describe differences in flame characteristics, fouling, slagging and corrosion for coal combustion under air-firing and oxygen-firing conditions, including sensitivity to oxy-burner design and flue gas recycle composition. 2) Validated mechanisms developed from test data that describe fouling, slagging, waterwall corrosion, heat transfer, char burnout and sooting under coal oxy-combustion conditions. The mechanisms were presented in a form suitable for inclusion in CFD models or process models. 3) Principles to guide design of pilot-scale and full-scale coal oxy-firing systems and flue gas recycle configurations, such that boiler operational impacts from oxy-combustion retrofits are minimized. 4) Assessment of oxy-combustion impacts in two full-scale coal-fired utility boiler retrofits based on computational fluid dynamics (CFD) modeling of air-fired and oxygen-fired operation. This research determined that it is technically feasible to retrofit the combustion system in an air-fired boiler for oxy-fired operation. The impacts of CO{sub 2} flue gas recycle and burner design on flame characteristics (burnout, NO{sub x}, SO{sub x}, mercury and fine particle emissions, heat transfer) and operational concerns (fouling, slagging and corrosion) were minimal, with the exception of high sulfur levels resulting from untreated flue gas recycle with medium and high-sulfur coals. This work focused on combustion in the radiant and convective sections of the boiler and did not address boiler system integration issues, plant efficiencies, impacts on downstream air pollution control devices, or CO{sub 2} capture and compression. The experimental data, oxy-firing system principles and oxy-combustion process mechanisms provided by this work can be used by electric utilities, boiler OEMs, equipment suppliers, design firms, software vendors, consultants and government agencies to assess retrofit applications of oxy-combustion technologies to existing boilers and to guide development of new designs.« less

MASS CALIBRATION AND COSMOLOGICAL ANALYSIS OF THE SPT-SZ GALAXY CLUSTER SAMPLE USING VELOCITY DISPERSION σ {sub v} AND X-RAY Y {sub X} MEASUREMENTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bocquet, S.; Saro, A.; Mohr, J. J.

2015-02-01

We present a velocity-dispersion-based mass calibration of the South Pole Telescope Sunyaev-Zel'dovich effect survey (SPT-SZ) galaxy cluster sample. Using a homogeneously selected sample of 100 cluster candidates from 720 deg{sup 2} of the survey along with 63 velocity dispersion (σ {sub v}) and 16 X-ray Y {sub X} measurements of sample clusters, we simultaneously calibrate the mass-observable relation and constrain cosmological parameters. Our method accounts for cluster selection, cosmological sensitivity, and uncertainties in the mass calibrators. The calibrations using σ {sub v} and Y {sub X} are consistent at the 0.6σ level, with the σ {sub v} calibration preferring ∼16% highermore » masses. We use the full SPT{sub CL} data set (SZ clusters+σ {sub v}+Y {sub X}) to measure σ{sub 8}(Ω{sub m}/0.27){sup 0.3} = 0.809 ± 0.036 within a flat ΛCDM model. The SPT cluster abundance is lower than preferred by either the WMAP9 or Planck+WMAP9 polarization (WP) data, but assuming that the sum of the neutrino masses is ∑m {sub ν} = 0.06 eV, we find the data sets to be consistent at the 1.0σ level for WMAP9 and 1.5σ for Planck+WP. Allowing for larger ∑m {sub ν} further reconciles the results. When we combine the SPT{sub CL} and Planck+WP data sets with information from baryon acoustic oscillations and Type Ia supernovae, the preferred cluster masses are 1.9σ higher than the Y {sub X} calibration and 0.8σ higher than the σ {sub v} calibration. Given the scale of these shifts (∼44% and ∼23% in mass, respectively), we execute a goodness-of-fit test; it reveals no tension, indicating that the best-fit model provides an adequate description of the data. Using the multi-probe data set, we measure Ω{sub m} = 0.299 ± 0.009 and σ{sub 8} = 0.829 ± 0.011. Within a νCDM model we find ∑m {sub ν} = 0.148 ± 0.081 eV. We present a consistency test of the cosmic growth rate using SPT clusters. Allowing both the growth index γ and the dark energy equation-of-state parameter w to vary, we find γ = 0.73 ± 0.28 and w = –1.007 ± 0.065, demonstrating that the expansion and the growth histories are consistent with a ΛCDM universe (γ = 0.55; w = –1)« less

Scaling up delivery of contraceptive implants in sub-Saharan Africa: operational experiences of Marie Stopes International

PubMed Central

Duvall, Susan; Thurston, Sarah; Weinberger, Michelle; Nuccio, Olivia; Fuchs-Montgomery, Nomi

2014-01-01

Contraceptive implants offer promising opportunities for addressing the high and growing unmet need for modern contraceptives in sub-Saharan Africa. Marie Stopes International (MSI) offers implants as one of many family planning options. Between 2008 and 2012, MSI scaled up voluntary access to implants in 15 sub-Saharan African countries, from 80,041 implants in 2008 to 754,329 implants in 2012. This 9-fold increase amounted to more than 1.7 million implants delivered cumulatively over the 5-year period. High levels of client satisfaction were attained alongside service provision scale up by using existing MSI service delivery channels—mobile outreach, social franchising, and clinics—to implement strategies that broadened access for underserved clients and maintained service quality. Use of adaptive and context-specific service delivery models and attention to key operational components, including sufficient numbers of trained providers, strong supply chains, diverse financing mechanisms, and implant removal services, underpinned our service delivery efforts. Accounting for 70% of the implants delivered by MSI in 2012, mobile outreach services through dedicated MSI provider teams played a central role in scale-up efforts, fueled in part by the provision of free or heavily subsidized services. Social franchising also demonstrated promise for future program growth, along with MSI clinics. Continued high growth in implant provision between 2011 and 2012 in all sub-Saharan African countries indicates the region's capacity for further service delivery expansion. Meeting the expected rising demand for implants and ensuring long-term sustainable access to the method, as part of a comprehensive method mix, will require continued use of appropriate service delivery models, effective operations, and ongoing collaboration between the private, public, and nongovernmental sectors. MSI's experience can be instructive for future efforts to ensure contraceptive access and choice in sub-Saharan Africa, especially as the global health community works to achieve its Family Planning 2020 (FP2020) commitments to expand family planning access to 120 million new users. PMID:25276564

Scaling up delivery of contraceptive implants in sub-Saharan Africa: operational experiences of Marie Stopes International.

PubMed

Duvall, Susan; Thurston, Sarah; Weinberger, Michelle; Nuccio, Olivia; Fuchs-Montgomery, Nomi

2014-02-01

Contraceptive implants offer promising opportunities for addressing the high and growing unmet need for modern contraceptives in sub-Saharan Africa. Marie Stopes International (MSI) offers implants as one of many family planning options. Between 2008 and 2012, MSI scaled up voluntary access to implants in 15 sub-Saharan African countries, from 80,041 implants in 2008 to 754,329 implants in 2012. This 9-fold increase amounted to more than 1.7 million implants delivered cumulatively over the 5-year period. High levels of client satisfaction were attained alongside service provision scale up by using existing MSI service delivery channels-mobile outreach, social franchising, and clinics-to implement strategies that broadened access for underserved clients and maintained service quality. Use of adaptive and context-specific service delivery models and attention to key operational components, including sufficient numbers of trained providers, strong supply chains, diverse financing mechanisms, and implant removal services, underpinned our service delivery efforts. Accounting for 70% of the implants delivered by MSI in 2012, mobile outreach services through dedicated MSI provider teams played a central role in scale-up efforts, fueled in part by the provision of free or heavily subsidized services. Social franchising also demonstrated promise for future program growth, along with MSI clinics. Continued high growth in implant provision between 2011 and 2012 in all sub-Saharan African countries indicates the region's capacity for further service delivery expansion. Meeting the expected rising demand for implants and ensuring long-term sustainable access to the method, as part of a comprehensive method mix, will require continued use of appropriate service delivery models, effective operations, and ongoing collaboration between the private, public, and nongovernmental sectors. MSI's experience can be instructive for future efforts to ensure contraceptive access and choice in sub-Saharan Africa, especially as the global health community works to achieve its Family Planning 2020 (FP2020) commitments to expand family planning access to 120 million new users.

Fusion of infrared and visible images based on BEMD and NSDFB

NASA Astrophysics Data System (ADS)

Zhu, Pan; Huang, Zhanhua; Lei, Hai

2016-07-01

This paper presents a new fusion method based on the adaptive multi-scale decomposition of bidimensional empirical mode decomposition (BEMD) and the flexible directional expansion of nonsubsampled directional filter banks (NSDFB) for visible-infrared images. Compared with conventional multi-scale fusion methods, BEMD is non-parametric and completely data-driven, which is relatively more suitable for non-linear signals decomposition and fusion. NSDFB can provide direction filtering on the decomposition levels to capture more geometrical structure of the source images effectively. In our fusion framework, the entropies of the two patterns of source images are firstly calculated and the residue of the image whose entropy is larger is extracted to make it highly relevant with the other source image. Then, the residue and the other source image are decomposed into low-frequency sub-bands and a sequence of high-frequency directional sub-bands in different scales by using BEMD and NSDFB. In this fusion scheme, two relevant fusion rules are used in low-frequency sub-bands and high-frequency directional sub-bands, respectively. Finally, the fused image is obtained by applying corresponding inverse transform. Experimental results indicate that the proposed fusion algorithm can obtain state-of-the-art performance for visible-infrared images fusion in both aspects of objective assessment and subjective visual quality even for the source images obtained in different conditions. Furthermore, the fused results have high contrast, remarkable target information and rich details information that are more suitable for human visual characteristics or machine perception.

Solid Polymer Electrolyte Fuel Cell Technology Program

NASA Technical Reports Server (NTRS)

1980-01-01

Work is reported on phase 5 of the Solid Polymer Electrolyte (SPE) Fuel Cell Technology Development program. The SPE fuel cell life and performance was established at temperatures, pressures, and current densities significantly higher than those previously demonstrated in sub-scale hardware. Operation of single-cell Buildup No. 1 to establish life capabilities of the full-scale hardware was continued. A multi-cell full-scale unit (Buildup No. 2) was designed, fabricated, and test evaluated laying the groundwork for the construction of a reactor stack. A reactor stack was then designed, fabricated, and successfully test-evaluated to demonstrate the readiness of SPE fuel cell technology for future space applications.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sakaguchi, Hidetsugu; Malomed, Boris A.

We study ordinary solitons and gap solitons (GS's) in the framework of the one-dimensional Gross-Pitaevskii equation (GPE) with a combination of both linear and nonlinear lattice potentials. The main points of the analysis are the effects of (in)commensurability between the lattices, the development of analytical methods, viz., the variational approximation (VA) for narrow ordinary solitons and various forms of the averaging method for broad solitons of both types, and also the study of the mobility of the solitons. Under the direct commensurability (equal periods of the lattices, L{sub lin}=L{sub nonlin}), the family of ordinary solitons is similar to its counterpartmore » in the GPE without external potentials. In the case of the subharmonic commensurability with L{sub lin}=(1/2)L{sub nonlin}, or incommensurability, there is an existence threshold for the ordinary solitons and the scaling relation between their amplitude and width is different from that in the absence of the potentials. GS families demonstrate a bistability unless the direct commensurability takes place. Specific scaling relations are found for them as well. Ordinary solitons can be readily set in motion by kicking. GS's are also mobile and feature inelastic collisions. The analytical approximations are shown to be quite accurate, predicting correct scaling relations for the soliton families in different cases. The stability of the ordinary solitons is fully determined by the Vakhitov-Kolokolov (VK) criterion (i.e., a negative slope in the dependence between the solitons's chemical potential mu and norm N). The stability of GS families obeys an inverted ('anti-VK') criterion dmu/dN>0, which is explained by the approximation based on the averaging method. The present system provides for the unique possibility to check the anti-VK criterion, as mu(N) dependencies for GS's feature turning points except in the case of direct commensurability.« less

Generalized emission functions for photon emission from quark-gluon plasma

DOE Office of Scientific and Technical Information (OSTI.GOV)

Suryanarayana, S. V.

The Landau-Pomeranchuk-Migdal effects on photon emission from the quark-gluon plasma have been studied as a function of photon mass, at a fixed temperature of the plasma. The integral equations for the transverse vector function [f-tilde)(p-tilde){sub (perpendicular)})] and the longitudinal function [g-tilde)(p-tilde){sub (perpendicular)})] consisting of multiple scattering effects are solved by the self-consistent iterations method and also by the variational method for the variable set {l_brace}p{sub 0},q{sub 0},Q{sup 2}{r_brace}. We considered the bremsstrahlung and the off shell annihilation (aws) processes. We define two new dynamical scaling variables, x{sub T},x{sub L}, for bremsstrahlung and aws processes which are functions of variables p{submore » 0},q{sub 0},Q{sup 2}. We define four new emission functions for massive photon emission represented by g{sub T}{sup b},g{sub T}{sup a},g{sub L}{sup b},g{sub L}{sup a} and we constructed these using the exact numerical solutions of the integral equations. These four emission functions have been parametrized by suitable simple empirical fits. Using the empirical emission functions, we calculated the imaginary part of the photon polarization tensor as a function of photon mass and energy.« less

Large-scale assembly bias of dark matter halos

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lazeyras, Titouan; Musso, Marcello; Schmidt, Fabian, E-mail: titouan@mpa-garching.mpg.de, E-mail: mmusso@sas.upenn.edu, E-mail: fabians@mpa-garching.mpg.de

We present precise measurements of the assembly bias of dark matter halos, i.e. the dependence of halo bias on other properties than the mass, using curved 'separate universe' N-body simulations which effectively incorporate an infinite-wavelength matter overdensity into the background density. This method measures the LIMD (local-in-matter-density) bias parameters b {sub n} in the large-scale limit. We focus on the dependence of the first two Eulerian biases b {sup E} {sup {sub 1}} and b {sup E} {sup {sub 2}} on four halo properties: the concentration, spin, mass accretion rate, and ellipticity. We quantitatively compare our results with previous worksmore » in which assembly bias was measured on fairly small scales. Despite this difference, our findings are in good agreement with previous results. We also look at the joint dependence of bias on two halo properties in addition to the mass. Finally, using the excursion set peaks model, we attempt to shed new insights on how assembly bias arises in this analytical model.« less

Scabies in residential care homes: Modelling, inference and interventions for well-connected population sub-units

PubMed Central

Middleton, Jo; Güttel, Stefan; Cassell, Jackie; Ross, Joshua

2018-01-01

In the context of an ageing population, understanding the transmission of infectious diseases such as scabies through well-connected sub-units of the population, such as residential care homes, is particularly important for the design of efficient interventions to mitigate against the effects of those diseases. Here, we present a modelling methodology based on the efficient solution of a large-scale system of linear differential equations that allows statistical calibration of individual-based random models to real data on scabies in residential care homes. In particular, we review and benchmark different numerical methods for the integration of the differential equation system, and then select the most appropriate of these methods to perform inference using Markov chain Monte Carlo. We test the goodness-of-fit of this model using posterior predictive intervals and propagate forward the resulting parameter uncertainty in a Bayesian framework to consider the economic cost of delayed interventions against scabies, quantifying the benefits of prompt action in the event of detection. We also revisit the previous methodology used to assess the safety of treatments in small population sub-units—in this context ivermectin—and demonstrate that even a very slight relaxation of the implicit assumption of homogeneous death rates significantly increases the plausibility of the hypothesis that ivermectin does not cause excess mortality based upon the data of Barkwell and Shields. PMID:29579037

SWAT-CS: Revision and testing of SWAT for Canadian Shield catchments

NASA Astrophysics Data System (ADS)

Fu, Congsheng; James, April L.; Yao, Huaxia

2014-04-01

Canadian Shield catchments are under increasing pressure from various types of development (e.g., mining and increased cottagers) and changing climate. Within the southern part of the Canadian Shield, catchments are generally characterized by shallow forested soils with high infiltration rates and low bedrock infiltration, generating little overland flow, and macropore and subsurface flow are important streamflow generation processes. Large numbers of wetlands and lakes are also key physiographic features, and snow-processes are critical to catchment modeling in this climate. We have revised the existing, publicly available SWAT (version 2009.10.1 Beta 3) to create SWAT-CS, a version representing hydrological processes dominating Canadian Shield catchments, where forest extends over Precambrian Shield bedrock. Prior to this study, very few studies applying SWAT to Canadian Shield catchments exist (we have found three). We tested SWAT-CS using the Harp Lake catchment dataset, an Ontario Ministry of Environment research station located in south-central Ontario. Simulations were evaluated against 30 years of observational data, including streamflow from six headwater sub-catchments (0.1-1.9 km2), outflow from Harp Lake (5.4 km2) and five years of weekly snow water equivalent (SWE). The best Nash-Sutcliffe efficiency (NSE) results for daily streamflow calibration, daily streamflow validation, and SWE were 0.60, 0.65, and 0.87, respectively, for sub-catchment HP4 (with detailed land use and soil data). For this range of catchment scales, land cover and soil properties were found to be transferable across sub-catchments with similar physiographic features, namely streamflow from the remaining five sub-catchments could be modeled well using sub-catchment HP4 parameterization. The Harp Lake outflow was well modeled using the existing reservoir-based target release method, generating NSEs of 0.72 and 0.67 for calibration and verification periods respectively. With significant changes to the infiltration module (introducing macropore flow and reduced bedrock percolation), more than 90% of interflow was generated close to the soil-bedrock interface and the contribution of groundwater flow to total runoff was reduced to small amounts, consistent with hydrological process understanding in this terrain. These two changes also allowed for a positive linear relationship between NSE of SWE and Q, whereas prior to these changes there was a negative relationship. With these key revisions to the infiltration and bedrock percolations modules, it is concluded that SWAT-CS can reasonably capture key hydrological processes within Canadian Shield catchments. Further testing will examine water quality modeling and larger-scale applications.

Micro-positron emission tomography for measuring sub-core scale single and multiphase transport parameters in porous media

NASA Astrophysics Data System (ADS)

Zahasky, Christopher; Benson, Sally M.

2018-05-01

Accurate descriptions of heterogeneity in porous media are important for understanding and modeling single phase (e.g. contaminant transport, saltwater intrusion) and multiphase (e.g. geologic carbon storage, enhanced oil recovery) transport problems. Application of medical imaging to experimentally quantify these processes has led to significant progress in material characterization and understanding fluid transport behavior at laboratory scales. While widely utilized in cancer diagnosis and management, cardiology, and neurology, positron emission tomography (PET) has had relatively limited applications in earth science. This study utilizes a small-bore micro-PET scanner to image and quantify the transport behavior of pulses of a conservative aqueous radiotracer injected during single and multiphase flow experiments in two heterogeneous Berea sandstone cores. The cores are discretized into axial-parallel streamtubes, and using the reconstructed micro-PET data, expressions are derived from spatial moment analysis for calculating sub-core tracer flux and pore water velocity. Using the flux and velocity measurements, it is possible to calculate porosity and saturation from volumetric flux balance, and calculate permeability and water relative permeability from Darcy's law. Second spatial moment analysis enables measurement of sub-core solute dispersion during both single phase and multiphase experiments. A numerical simulation model is developed to verify the assumptions of the streamtube dimension reduction technique. A variation of the reactor ratio is presented as a diagnostic metric to efficiently determine the validity of the streamtube approximation in core and column-scale experiments. This study introduces a new method to quantify sub-core permeability, relative permeability, and dispersion. These experimental and analytical methods provide a foundation for future work on experimental measurements of differences in transport behavior across scales.

Development and Validation of the Chinese Attitudes to Starting Insulin Questionnaire (Ch-ASIQ) for Primary Care Patients with Type 2 Diabetes

PubMed Central

Fu, Sau Nga; Chin, Weng Yee; Wong, Carlos King Ho; Yeung, Vincent Tok Fai; Yiu, Ming Pong; Tsui, Hoi Yee; Chan, Ka Hung

2013-01-01

Objectives To develop and evaluate the psychometric properties of a Chinese questionnaire which assesses the barriers and enablers to commencing insulin in primary care patients with poorly controlled Type 2 diabetes. Research Design and Method Questionnaire items were identified using literature review. Content validation was performed and items were further refined using an expert panel. Following translation, back translation and cognitive debriefing, the translated Chinese questionnaire was piloted on target patients. Exploratory factor analysis and item-scale correlations were performed to test the construct validity of the subscales and items. Internal reliability was tested by Cronbach’s alpha. Results Twenty-seven identified items underwent content validation, translation and cognitive debriefing. The translated questionnaire was piloted on 303 insulin naïve (never taken insulin) Type 2 diabetes patients recruited from 10 government-funded primary care clinics across Hong Kong. Sufficient variability in the dataset for factor analysis was confirmed by Bartlett’s Test of Sphericity (P<0.001). Using exploratory factor analysis with varimax rotation, 10 factors were generated onto which 26 items loaded with loading scores > 0.4 and Eigenvalues >1. Total variance for the 10 factors was 66.22%. Kaiser-Meyer-Olkin measure was 0.725. Cronbach’s alpha coefficients for the first four factors were ≥0.6 identifying four sub-scales to which 13 items correlated. Remaining sub-scales and items with poor internal reliability were deleted. The final 13-item instrument had a four scale structure addressing: ‘Self-image and stigmatization’; ‘Factors promoting self-efficacy; ‘Fear of pain or needles’; and ‘Time and family support’. Conclusion The Chinese Attitudes to Starting Insulin Questionnaire (Ch-ASIQ) appears to be a reliable and valid measure for assessing barriers to starting insulin. This short instrument is easy to administer and may be used by healthcare providers and researchers as an assessment tool for Chinese diabetic primary care patients, including the elderly, who are unwilling to start insulin. PMID:24236071

A rainfall disaggregation scheme for sub-hourly time scales: Coupling a Bartlett-Lewis based model with adjusting procedures

NASA Astrophysics Data System (ADS)

Kossieris, Panagiotis; Makropoulos, Christos; Onof, Christian; Koutsoyiannis, Demetris

2018-01-01

Many hydrological applications, such as flood studies, require the use of long rainfall data at fine time scales varying from daily down to 1 min time step. However, in the real world there is limited availability of data at sub-hourly scales. To cope with this issue, stochastic disaggregation techniques are typically employed to produce possible, statistically consistent, rainfall events that aggregate up to the field data collected at coarser scales. A methodology for the stochastic disaggregation of rainfall at fine time scales was recently introduced, combining the Bartlett-Lewis process to generate rainfall events along with adjusting procedures to modify the lower-level variables (i.e., hourly) so as to be consistent with the higher-level one (i.e., daily). In the present paper, we extend the aforementioned scheme, initially designed and tested for the disaggregation of daily rainfall into hourly depths, for any sub-hourly time scale. In addition, we take advantage of the recent developments in Poisson-cluster processes incorporating in the methodology a Bartlett-Lewis model variant that introduces dependence between cell intensity and duration in order to capture the variability of rainfall at sub-hourly time scales. The disaggregation scheme is implemented in an R package, named HyetosMinute, to support disaggregation from daily down to 1-min time scale. The applicability of the methodology was assessed on a 5-min rainfall records collected in Bochum, Germany, comparing the performance of the above mentioned model variant against the original Bartlett-Lewis process (non-random with 5 parameters). The analysis shows that the disaggregation process reproduces adequately the most important statistical characteristics of rainfall at wide range of time scales, while the introduction of the model with dependent intensity-duration results in a better performance in terms of skewness, rainfall extremes and dry proportions.

A systematic review of qualitative findings on factors enabling and deterring uptake of HIV testing in Sub-Saharan Africa

PubMed Central

2013-01-01

Background Despite Sub-Saharan Africa (SSA) being the epicenter of the HIV epidemic, uptake of HIV testing is not optimal. While qualitative studies have been undertaken to investigate factors influencing uptake of HIV testing, systematic reviews to provide a more comprehensive understanding are lacking. Methods Using Noblit and Hare’s meta-ethnography method, we synthesised published qualitative research to understand factors enabling and deterring uptake of HIV testing in SSA. We identified 5,686 citations out of which 56 were selected for full text review and synthesised 42 papers from 13 countries using Malpass’ notion of first-, second-, and third-order constructs. Results The predominant factors enabling uptake of HIV testing are deterioration of physical health and/or death of sexual partner or child. The roll-out of various HIV testing initiatives such as ‘opt-out’ provider-initiated HIV testing and mobile HIV testing has improved uptake of HIV testing by being conveniently available and attenuating fear of HIV-related stigma and financial costs. Other enabling factors are availability of treatment and social network influence and support. Major barriers to uptake of HIV testing comprise perceived low risk of HIV infection, perceived health workers’ inability to maintain confidentiality and fear of HIV-related stigma. While the increasingly wider availability of life-saving treatment in SSA is an incentive to test, the perceived psychological burden of living with HIV inhibits uptake of HIV testing. Other barriers are direct and indirect financial costs of accessing HIV testing, and gender inequality which undermines women’s decision making autonomy about HIV testing. Despite differences across SSA, the findings suggest comparable factors influencing HIV testing. Conclusions Improving uptake of HIV testing requires addressing perception of low risk of HIV infection and perceived inability to live with HIV. There is also a need to continue addressing HIV-related stigma, which is intricately linked to individual economic support. Building confidence in the health system through improving delivery of health care and scaling up HIV testing strategies that attenuate social and economic costs of seeking HIV testing could also contribute towards increasing uptake of HIV testing in SSA. PMID:23497196

Recent advances with quiescent power supply current (I(sub DDQ)) testing at Sandia using the HP82000

NASA Astrophysics Data System (ADS)

Righter, A. W.; Leong, D. J.; Cox, L. B.

Last year at the HP82000 Users Group Meeting, Sandia National Laboratories gave a presentation on I(sub DDQ) testing. This year, some advances are presented on this testing including DUT board fixturing, external DC PMU measurement, and automatic IDD-All circuit calibration. Implementation is examined more than theory, with results presented from Sandia tests. After a brief summary I(sub DDQ) theory and testing concepts, how the break (hold state) vector and data formatting present a test vector generation concern for the HP82000 is described. Fixturing of the DUT board for both types of I(sub DDQ) measurement is then discussed, along with how the continuity test and test vector generation must be taken into account. Results of a test including continuity, IDD-All and I(sub DDQ) Value measurements is shown. Next, measurement of low current using an external PMU is discussed, including noise considerations, implementation and some test results showing nA-range measurements. A method is presented for automatic calibration of the IDD-All analog comparator circuit using RM BASIC on the HP82000, with implementation and measurement results. Finally, future directions for research in this area is explored.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, Yidong; Chen, Xuelei; Wang, Xin

The Tianlai experiment is dedicated to the observation of large-scale structures (LSS) by the 21 cm intensity mapping technique. In this paper, we make forecasts concerning its ability to observe or constrain the dark energy parameters and the primordial non-Gaussianity. From the LSS data, one can use the baryon acoustic oscillation (BAO) and growth rate derived from the redshift space distortion (RSD) to measure the dark energy density and equation of state. The primordial non-Gaussianity can be constrained either by looking for scale-dependent bias in the power spectrum, or by using the bispectrum. Here, we consider three cases: the Tianlaimore » cylinder array pathfinder that is currently being built, an upgrade of the Pathfinder Array with more receiver units, and the full-scale Tianlai cylinder array. Using the full-scale Tianlai experiment, we expect σ{sub w{sub 0}}∼0.082 and σ{sub w{sub a}}∼0.21 from the BAO and RSD measurements, σ{sub f{sub N{sub L}{sup local}}}∼14 from the power spectrum measurements with scale-dependent bias, and σ{sub f{sub N{sub L}{sup local}}}∼22 and σ{sub f{sub N{sub L}{sup equil}}}∼157 from the bispectrum measurements.« less

Synergistic cross-scale coupling of turbulence in a tokamak plasma

DOE Office of Scientific and Technical Information (OSTI.GOV)

Howard, N. T., E-mail: nthoward@psfc.mit.edu; Holland, C.; White, A. E.

2014-11-15

For the first time, nonlinear gyrokinetic simulations spanning both the ion and electron spatio-temporal scales have been performed with realistic electron mass ratio ((m{sub D}∕m{sub e}){sup 1∕2 }= 60.0), realistic geometry, and all experimental inputs, demonstrating the coexistence and synergy of ion (k{sub θ}ρ{sub s}∼O(1.0)) and electron-scale (k{sub θ}ρ{sub e}∼O(1.0)) turbulence in the core of a tokamak plasma. All multi-scale simulations utilized the GYRO code [J. Candy and R. E. Waltz, J. Comput. Phys. 186, 545 (2003)] to study the coupling of ion and electron-scale turbulence in the core (r/a = 0.6) of an Alcator C-Mod L-mode discharge shown previously to exhibit an under-predictionmore » of the electron heat flux when using simulations only including ion-scale turbulence. Electron-scale turbulence is found to play a dominant role in setting the electron heat flux level and radially elongated (k{sub r} ≪ k{sub θ}) “streamers” are found to coexist with ion-scale eddies in experimental plasma conditions. Inclusion of electron-scale turbulence in these simulations is found to increase both ion and electron heat flux levels by enhancing the transport at the ion-scale while also driving electron heat flux at sub-ρ{sub i} scales. The combined increases in the low and high-k driven electron heat flux may explain previously observed discrepancies between simulated and experimental electron heat fluxes and indicates a complex interaction of short and long wavelength turbulence.« less

Propagation of an ultrashort, intense laser pulse in a relativistic plasma

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ritchie, B.; Decker, C.D.

1997-12-31

A Maxwell-relativistic fluid model is developed for the propagation of an ultrashort, intense laser pulse through an underdense plasma. The separability of plasma and optical frequencies ({omega}{sub p} and {omega} respectively) for small {omega}{sub p}/{omega} is not assumed; thus the validity of multiple-scales theory (MST) can be tested. The theory is valid when {omega}{sub p}/{omega} is of order unity or for cases in which {omega}{sub p}/{omega} {much_lt} 1 but strongly relativistic motion causes higher-order plasma harmonics to be generated which overlap the region of the first-order laser harmonic, such that MST would not expected to be valid although its principalmore » validity criterion {omega}{sub p}/{omega} {much_lt} 1 holds.« less

A Scale-Invariant Model of Statistical Mechanics and Modified Forms of the First and the Second Laws of Thermodynamics

NASA Technical Reports Server (NTRS)

Sohrab, Siavash H.; Pitch, Nancy (Technical Monitor)

1999-01-01

A scale-invariant statistical theory of fields is presented that leads to invariant definition of density, velocity, temperature, and pressure, The definition of Boltzmann constant is introduced as k(sub k) = m(sub k)v(sub k)c = 1.381 x 10(exp -23) J x K(exp -1), suggesting that the Kelvin absolute temperature scale is equivalent to a length scale. Two new state variables called the reversible heat Q(sub rev) = TS and the reversible work W(sub rev) = PV are introduced. The modified forms of the first and second law of thermodynamics are presented. The microscopic definition of heat (work) is presented as the kinetic energy due to the random (peculiar) translational, rotational, and pulsational motions. The Gibbs free energy of an element at scale Beta is identified as the total system energy at scale (Beta-1), thus leading to an invariant form of the first law of thermodynamics U(sub Beta) = Q(sub Beta) - W(sub Beta) +N(e3)U(sub Beta-1).

Stationary table CT dosimetry and anomalous scanner-reported values of CTDI{sub vol}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dixon, Robert L., E-mail: rdixon@wfubmc.edu; Boone, John M.

2014-01-15

Purpose: Anomalous, scanner-reported values of CTDI{sub vol} for stationary phantom/table protocols (having elevated values of CTDI{sub vol} over 300% higher than the actual dose to the phantom) have been observed; which are well-beyond the typical accuracy expected of CTDI{sub vol} as a phantom dose. Recognition of these outliers as “bad data” is important to users of CT dose index tracking systems (e.g., ACR DIR), and a method for recognition and correction is provided. Methods: Rigorous methods and equations are presented which describe the dose distributions for stationary-table CT. A comparison with formulae for scanner-reported values of CTDI{sub vol} clearly identifiesmore » the source of these anomalies. Results: For the stationary table, use of the CTDI{sub 100} formula (applicable to a moving phantom only) overestimates the dose due to extra scatter and also includes an overbeaming correction, both of which are nonexistent when the phantom (or patient) is held stationary. The reported DLP remains robust for the stationary phantom. Conclusions: The CTDI-paradigm does not apply in the case of a stationary phantom and simpler nonintegral equations suffice. A method of correction of the currently reported CTDI{sub vol} using the approach-to-equilibrium formula H(a) and an overbeaming correction factor serves to scale the reported CTDI{sub vol} values to more accurate levels for stationary-table CT, as well as serving as an indicator in the detection of “bad data.”.« less

APPLICATION OF VACUUM SALT DISTILLATION TECHNOLOGY FOR THE REMOVAL OF FLUORIDE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pierce, R.; Pak, D.

2011-08-10

Vacuum distillation of chloride salts from plutonium oxide (PuO{sub 2}) and simulant PuO{sub 2} has been previously demonstrated at Department of Energy (DOE) sites using kilogram quantities of chloride salt. The apparatus for vacuum distillation contains a zone heated using a furnace and a zone actively cooled using either recirculated water or compressed air. During a vacuum distillation operation, a sample boat containing the feed material is placed into the apparatus while it is cool, and the system is sealed. The system is evacuated using a vacuum pump. Once a sufficient vacuum is attained, heating begins. Volatile salts distill frommore » the heated zone to the cooled zone where they condense, leaving behind the non-volatile materials in the feed boat. The application of vacuum salt distillation (VSD) is of interest to the HB-Line Facility and the MOX Fuel Fabrication Facility (MFFF) at the Savannah River Site (SRS). Both facilities are involved in efforts to disposition excess fissile materials. Many of these materials contain chloride and fluoride salt concentrations which make them unsuitable for dissolution without prior removal of the chloride and fluoride salts. Between September 2009 and January 2011, the Savannah River National Laboratory (SRNL) and HB-Line designed, developed, tested, and successfully deployed a system for the distillation of chloride salts. Subsequent efforts are attempting to adapt the technology for the removal of fluoride. Fluoride salts of interest are less-volatile than the corresponding chloride salts. Consequently, an alternate approach is required for the removal of fluoride without significantly increasing the operating temperature. HB-Line Engineering requested SRNL to evaluate and demonstrate the feasibility of an alternate approach using both non-radioactive simulants and plutonium-bearing materials. Whereas the earlier developments targeted the removal of sodium chloride (NaCl) and potassium chloride (KCl), the current activities are concerned with the removal of the halide ions associated with plutonium trifluoride (PuF{sub 3}), plutonium tetrafluoride (PuF{sub 4}), calcium fluoride (CaF{sub 2}), and calcium chloride (CaCl{sub 2}). This report discusses non-radioactive testing of small-scale and pilot-scale systems and radioactive testing of a small-scale system. Experiments focused on demonstrating the chemistry for halide removal and addressing the primary engineering questions associated with a change in the process chemistry.« less

High temperature oxidation behavior of austenitic stainless steel AISI 304 in steam of nanofluids contain nanoparticle ZrO2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prajitno, Djoko Hadi, E-mail: djokohp@batan.go.id; Syarif, Dani Gustaman, E-mail: djokohp@batan.go.id

2014-03-24

The objective of this study is to evaluate high temperature oxidation behavior of austenitic stainless steel SS 304 in steam of nanofluids contain nanoparticle ZrO{sub 2}. The oxidation was performed at high temperatures ranging from 600 to 800°C. The oxidation time was 60 minutes. After oxidation the surface of the samples was analyzed by different methods including, optical microscope, scanning electron microscope (SEM) and X-ray diffraction (XRD). X-ray diffraction examination show that the oxide scale formed during oxidation of stainless steel AISI 304 alloys is dominated by iron oxide, Fe{sub 2}O{sub 3}. Minor element such as Cr{sub 2}O{sub 3} ismore » also appeared in the diffraction pattern. Characterization by optical microscope showed that cross section microstructure of stainless steel changed after oxidized with the oxide scale on the surface stainless steels. SEM and x-ray diffraction examination show that the oxide of ZrO{sub 2} appeared on the surface of stainless steel. Kinetic rate of oxidation of austenite stainless steel AISI 304 showed that increasing oxidation temperature and time will increase oxidation rate.« less

[Evaluation of a two-dimensional scale for the assessment of fear avoidance beliefs in elderly chronic low back pain patients].

PubMed

Quint, S; Raich, M; Luckmann, J

2011-06-01

There is evidence on the importance of fear avoidance beliefs (FAB) as prognostic risk factors in elderly patients suffering from chronic low back pain (CLBP). However, so far there is no validated German instrument for measuring FAB in elderly CLBP patients. The aim of the study presented was to evaluate the psychometric properties of the Catastrophizing Avoidance Scale D-65+ (CAS-D-65+) within a population of elderly patients with CLBP. A cross-sectional study was conducted with measurement repeated after 4 weeks in 68 CLBP patients aged 64 years and older. The CAS-D-65+ was analyzed performing an item analysis and retest reliability. For validation standardized assessment methods (Tampa Scale of Kinesiophobia [TSK], Photography of Daily Activity - Short electronic Version [Phoda-SeV], 5-Item-FAB, pain, disability, well-being and strain) were used. Internal consistency (Cronbach's α) ranged from 0.87 to 0.92 for total scale and from 0.71 to 0.89 for the sub-scales "catastrophizing" and "avoidance", retest reliability (r(tt)) ranged from 0.67 for the sub-scale "catastrophizing" to 0.70 for total scale and sub-scale "avoidance". The CAS-D-65+ showed moderate and strong effect sizes (Cohen's d) with other related FAB scales and external criteria. As shown in this study the CAS-D-65+ is a reliable and a valid instrument for the assessment of FAB in older patients with CLBP.

Exploring depression, self-esteem and verbal fluency with different degrees of internet addiction among Chinese college students.

PubMed

Nie, Jia; Zhang, Wei; Liu, Ying

2017-01-01

The aims of this study were to explore depression, self-esteem and verbal fluency functions among normal internet users, mild internet addictions and severe internet addictions. The survey sample consisted of 316 college students, and their internet addiction symptoms, depression and self-esteem symptoms were assessed using the Revised Chen Internet Addiction Scale (CIAS-R), Zung Self-Rating Depression Scale (ZSDS), Rosenberg Self-Esteem Scale (RSES), respectively. From this sample, 16 students with non-addictions, 19 students with mild internet addiction (sub-MIA) and 15 students with severe internet addiction (sub-SIA) were recruited and subjected to the classical verbal fluency tests, including the semantic and phonemic fluency task. The results indicated that severe internet addiction in the survey sample showed the highest tendency towards depressive symptoms and lowest self-esteem scores, and sub-SIA showed poor performance on the semantic fluency task. In conclusion, severe internet addiction was significantly associated with depression, low self-esteem and semantic verbal fluency problems. Copyright © 2017 Elsevier Inc. All rights reserved.

GAMMA-RAY BURST HOST GALAXY SURVEYS AT REDSHIFT z {approx}> 4: PROBES OF STAR FORMATION RATE AND COSMIC REIONIZATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Trenti, Michele; Perna, Rosalba; Levesque, Emily M.

2012-04-20

Measuring the star formation rate (SFR) at high redshift is crucial for understanding cosmic reionization and galaxy formation. Two common complementary approaches are Lyman break galaxy (LBG) surveys for large samples and gamma-ray burst (GRB) observations for sensitivity to SFR in small galaxies. The z {approx}> 4 GRB-inferred SFR is higher than the LBG rate, but this difference is difficult to understand, as both methods rely on several modeling assumptions. Using a physically motivated galaxy luminosity function model, with star formation in dark matter halos with virial temperature T{sub vir} {approx}> 2 Multiplication-Sign 10{sup 4} K (M{sub DM} {approx}> 2more » Multiplication-Sign 10{sup 8} M{sub Sun }), we show that GRB- and LBG-derived SFRs are consistent if GRBs extend to faint galaxies (M{sub AB} {approx}< -11). To test star formation below the detection limit L{sub lim} {approx} 0.05L*{sub z=3} of LBG surveys, we propose to measure the fraction f{sub det}(L > L{sub lim}, z) of GRB hosts with L > L{sub lim}. This fraction quantifies the missing star formation fraction in LBG surveys, constraining the mass-suppression scale for galaxy formation, with weak dependence on modeling assumptions. Because f{sub det}(L > L{sub lim}, z) corresponds to the ratio of SFRs derived from LBG and GRB surveys, if these estimators are unbiased, measuring f{sub det}(L > L{sub lim}, z) also constrains the redshift evolution of the GRB production rate per unit mass of star formation. Our analysis predicts significant success for GRB host detections at z {approx} 5 with f{sub det}(L > L{sub lim}, z) {approx} 0.4, but rarer detections at z > 6. By analyzing the upper limits on host galaxy luminosities of six z > 5 GRBs from literature data, we infer that galaxies with M{sub AB} > -15 were present at z > 5 at 95% confidence, demonstrating the key role played by very faint galaxies during reionization.« less

Broadband distortion modeling in Lyman-α forest BAO fitting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blomqvist, Michael; Kirkby, David; Margala, Daniel, E-mail: cblomqvi@uci.edu, E-mail: dkirkby@uci.edu, E-mail: dmargala@uci.edu

2015-11-01

In recent years, the Lyman-α absorption observed in the spectra of high-redshift quasars has been used as a tracer of large-scale structure by means of the three-dimensional Lyman-α forest auto-correlation function at redshift z≅ 2.3, but the need to fit the quasar continuum in every absorption spectrum introduces a broadband distortion that is difficult to correct and causes a systematic error for measuring any broadband properties. We describe a k-space model for this broadband distortion based on a multiplicative correction to the power spectrum of the transmitted flux fraction that suppresses power on scales corresponding to the typical length of amore » Lyman-α forest spectrum. Implementing the distortion model in fits for the baryon acoustic oscillation (BAO) peak position in the Lyman-α forest auto-correlation, we find that the fitting method recovers the input values of the linear bias parameter b{sub F} and the redshift-space distortion parameter β{sub F} for mock data sets with a systematic error of less than 0.5%. Applied to the auto-correlation measured for BOSS Data Release 11, our method improves on the previous treatment of broadband distortions in BAO fitting by providing a better fit to the data using fewer parameters and reducing the statistical errors on β{sub F} and the combination b{sub F}(1+β{sub F}) by more than a factor of seven. The measured values at redshift z=2.3 are β{sub F}=1.39{sup +0.11 +0.24 +0.38}{sub −0.10 −0.19 −0.28} and b{sub F}(1+β{sub F})=−0.374{sup +0.007 +0.013 +0.020}{sub −0.007 −0.014 −0.022} (1σ, 2σ and 3σ statistical errors). Our fitting software and the input files needed to reproduce our main results are publicly available.« less

Sediment Core Extrusion Method at Millimeter Resolution Using a Calibrated, Threaded-rod.

PubMed

Schwing, Patrick T; Romero, Isabel C; Larson, Rebekka A; O'Malley, Bryan J; Fridrik, Erika E; Goddard, Ethan A; Brooks, Gregg R; Hastings, David W; Rosenheim, Brad E; Hollander, David J; Grant, Guy; Mulhollan, Jim

2016-08-17

Aquatic sediment core subsampling is commonly performed at cm or half-cm resolution. Depending on the sedimentation rate and depositional environment, this resolution provides records at the annual to decadal scale, at best. An extrusion method, using a calibrated, threaded-rod is presented here, which allows for millimeter-scale subsampling of aquatic sediment cores of varying diameters. Millimeter scale subsampling allows for sub-annual to monthly analysis of the sedimentary record, an order of magnitude higher than typical sampling schemes. The extruder consists of a 2 m aluminum frame and base, two core tube clamps, a threaded-rod, and a 1 m piston. The sediment core is placed above the piston and clamped to the frame. An acrylic sampling collar is affixed to the upper 5 cm of the core tube and provides a platform from which to extract sub-samples. The piston is rotated around the threaded-rod at calibrated intervals and gently pushes the sediment out the top of the core tube. The sediment is then isolated into the sampling collar and placed into an appropriate sampling vessel (e.g., jar or bag). This method also preserves the unconsolidated samples (i.e., high pore water content) at the surface, providing a consistent sampling volume. This mm scale extrusion method was applied to cores collected in the northern Gulf of Mexico following the Deepwater Horizon submarine oil release. Evidence suggests that it is necessary to sample at the mm scale to fully characterize events that occur on the monthly time-scale for continental slope sediments.

Sediment Core Extrusion Method at Millimeter Resolution Using a Calibrated, Threaded-rod

PubMed Central

Schwing, Patrick T.; Romero, Isabel C.; Larson, Rebekka A.; O'Malley, Bryan J.; Fridrik, Erika E.; Goddard, Ethan A.; Brooks, Gregg R.; Hastings, David W.; Rosenheim, Brad E.; Hollander, David J.; Grant, Guy; Mulhollan, Jim

2016-01-01

Aquatic sediment core subsampling is commonly performed at cm or half-cm resolution. Depending on the sedimentation rate and depositional environment, this resolution provides records at the annual to decadal scale, at best. An extrusion method, using a calibrated, threaded-rod is presented here, which allows for millimeter-scale subsampling of aquatic sediment cores of varying diameters. Millimeter scale subsampling allows for sub-annual to monthly analysis of the sedimentary record, an order of magnitude higher than typical sampling schemes. The extruder consists of a 2 m aluminum frame and base, two core tube clamps, a threaded-rod, and a 1 m piston. The sediment core is placed above the piston and clamped to the frame. An acrylic sampling collar is affixed to the upper 5 cm of the core tube and provides a platform from which to extract sub-samples. The piston is rotated around the threaded-rod at calibrated intervals and gently pushes the sediment out the top of the core tube. The sediment is then isolated into the sampling collar and placed into an appropriate sampling vessel (e.g., jar or bag). This method also preserves the unconsolidated samples (i.e., high pore water content) at the surface, providing a consistent sampling volume. This mm scale extrusion method was applied to cores collected in the northern Gulf of Mexico following the Deepwater Horizon submarine oil release. Evidence suggests that it is necessary to sample at the mm scale to fully characterize events that occur on the monthly time-scale for continental slope sediments. PMID:27585268

Solving large scale structure in ten easy steps with COLA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tassev, Svetlin; Zaldarriaga, Matias; Eisenstein, Daniel J., E-mail: stassev@cfa.harvard.edu, E-mail: matiasz@ias.edu, E-mail: deisenstein@cfa.harvard.edu

2013-06-01

We present the COmoving Lagrangian Acceleration (COLA) method: an N-body method for solving for Large Scale Structure (LSS) in a frame that is comoving with observers following trajectories calculated in Lagrangian Perturbation Theory (LPT). Unlike standard N-body methods, the COLA method can straightforwardly trade accuracy at small-scales in order to gain computational speed without sacrificing accuracy at large scales. This is especially useful for cheaply generating large ensembles of accurate mock halo catalogs required to study galaxy clustering and weak lensing, as those catalogs are essential for performing detailed error analysis for ongoing and future surveys of LSS. As anmore » illustration, we ran a COLA-based N-body code on a box of size 100 Mpc/h with particles of mass ≈ 5 × 10{sup 9}M{sub s}un/h. Running the code with only 10 timesteps was sufficient to obtain an accurate description of halo statistics down to halo masses of at least 10{sup 11}M{sub s}un/h. This is only at a modest speed penalty when compared to mocks obtained with LPT. A standard detailed N-body run is orders of magnitude slower than our COLA-based code. The speed-up we obtain with COLA is due to the fact that we calculate the large-scale dynamics exactly using LPT, while letting the N-body code solve for the small scales, without requiring it to capture exactly the internal dynamics of halos. Achieving a similar level of accuracy in halo statistics without the COLA method requires at least 3 times more timesteps than when COLA is employed.« less

An Investigation on the Level of Conscious Consumerism of Primary School Students in Terms of Various Variables

ERIC Educational Resources Information Center

Saglam, Halil Ibrahim

2010-01-01

The purpose of this is study is to analyze the level of conscious consumerism of primary school students. For that purpose, a 19-item scale consisting of three sub-dimensions was developed. In order to test conduct validity and reliability, the scale was administered on 113 students studying in Sakarya. In accordance with the data obtained, an…

Scales of Star Formation: Does Local Environment Matter?

NASA Astrophysics Data System (ADS)

Bittle, Lauren

2018-01-01

I will present my work on measuring molecular gas properties in local universe galaxies to assess the impact of local environment on the gas and thus star formation. I will also discuss the gas properties on spatial scales that span an order of magnitude to best understand the layers of star formation processes. Local environments within these galaxies include external mechanisms from starburst supernova shells, spiral arm structure, and superstar cluster radiation. Observations of CO giant molecular clouds (GMC) of ~150pc resolution in IC 10, the Local Group dwarf starburst, probe the large-scale diffuse gas, some of which are near supernova bubble ridges. We mapped CO clouds across the spiral NGC 7793 at intermediate scales of ~20pc resolution with ALMA. With the clouds, we can test theories of cloud formation and destruction in relation to the spiral arm pattern and cluster population from the HST LEGUS analysis. Addressing the smallest scales, I will show results of 30 Doradus ALMA observations of sub-parsec dense molecular gas clumps only 15pc away from a superstar cluster R136. Though star formation occurs directly from the collapse of densest molecular gas, we test theories of scale-free star formation, which suggests a constant slope of the mass function from ~150pc GMCs to sub-parsec clumps. Probing environments including starburst supernova shells, spiral arm structure, and superstar cluster radiation shed light on how these local external mechanisms affect the molecular gas at various scales of star formation.

Ground-Based Robotic Sensing of an Agricultural Sub-Canopy Environment

NASA Astrophysics Data System (ADS)

Burns, A.; Peschel, J.

2015-12-01

Airborne remote sensing is a useful method for measuring agricultural crop parameters over large areas; however, the approach becomes limited to above-canopy characterization as a crop matures due to reduced visual access of the sub-canopy environment. During the growth cycle of an agricultural crop, such as soybeans, the micrometeorology of the sub-canopy environment can significantly impact pod development and reduced yields may result. Larger-scale environmental conditions aside, the physical structure and configuration of the sub-canopy matrix will logically influence local climate conditions for a single plant; understanding the state and development of the sub-canopy could inform crop models and improve best practices but there are currently no low-cost methods to quantify the sub-canopy environment at a high spatial and temporal resolution over an entire growth cycle. This work describes the modification of a small tactical and semi-autonomous, ground-based robotic platform with sensors capable of mapping the physical structure of an agricultural row crop sub-canopy; a soybean crop is used as a case study. Point cloud data representing the sub-canopy structure are stored in LAS format and can be used for modeling and visualization in standard GIS software packages.

Simulation of substrate degradation in composting of sewage sludge

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang Jun; Gao Ding, E-mail: gaod@igsnrr.ac.c; Chen Tongbin

2010-10-15

To simulate the substrate degradation kinetics of the composting process, this paper develops a mathematical model with a first-order reaction assumption and heat/mass balance equations. A pilot-scale composting test with a mixture of sewage sludge and wheat straw was conducted in an insulated reactor. The BVS (biodegradable volatile solids) degradation process, matrix mass, MC (moisture content), DM (dry matter) and VS (volatile solid) were simulated numerically by the model and experimental data. The numerical simulation offered a method for simulating k (the first-order rate constant) and estimating k{sub 20} (the first-order rate constant at 20 {sup o}C). After comparison withmore » experimental values, the relative error of the simulation value of the mass of the compost at maturity was 0.22%, MC 2.9%, DM 4.9% and VS 5.2%, which mean that the simulation is a good fit. The k of sewage sludge was simulated, and k{sub 20}, k{sub 20s} (first-order rate coefficient of slow fraction of BVS at 20 {sup o}C) of the sewage sludge were estimated as 0.082 and 0.015 d{sup -1}, respectively.« less

Lithium manganese oxide (LiMn{sub 2}O{sub 4}) nanoparticles synthesized by hydrothermal method as adsorbent of lithium recovery process from geothermal fluid of Lumpur Sidoarjo

DOE Office of Scientific and Technical Information (OSTI.GOV)

Noerochim, Lukman, E-mail: lukman@mat-eng.its.ac.id; Sapputra, Gede Panca Ady; Widodo, Amien

2016-04-19

Lumpur Sidoarjo is one of geothermal fluid types which has a great potential as source of lithium. Adsorption method with Lithium Manganese Oxide (LiMn{sub 2}O{sub 4}) as an adsorbent has been chosen for lithium recovery process due to low production cost and environmental friendly. LiMn{sub 2}O{sub 4} was synthesized by hydrothermal method at 200 °C for 24 hrs, 48 hrs, and 72 hrs. As prepared LiMn{sub 2}O{sub 4} powder is treated by acid treatment with 0.5 M HCl solution for 24 hrs. XRD test result reveals that all of as-prepared samples are indexed as spinel structure of LiMn{sub 2}O{sub 4}more » (JCPDS card no 35-0782) with no impurity peaks detected. SEM images show that LiMn{sub 2}O{sub 4} has nanoparticles morphology with particle size around 25 nm. The highest adsorption efficiency of adsorbent is obtained by sample hydrothermal for 72 hrs with 42.76%.« less

Discriminant of validity the Wender Utah rating scale in Iranian adults.

PubMed

Farokhzadi, Farideh; Mohammadi, Mohammad Reza; Salmanian, Maryam

2014-01-01

The aim of this study is the normalization of the Wender Utah rating scale which is used to detect adults with Attention-Deficit and Hyperactivity Disorder (ADHD). Available sampling method was used to choose 400 parents of children (200 parents of children with ADHD as compared to 200 parents of normal children). Wender Utah rating scale, which has been designed to diagnose ADHD in adults, is filled out by each of the parents to most accurately diagnose of ADHD in parents. Wender Utah rating scale was divided into 6 sub scales which consist of dysthymia, oppositional defiant disorder; school work problems, conduct disorder, anxiety, and ADHD were analyzed with exploratory factor analysis method. The value of (Kaiser-Meyer-Olkin) KMO was 86.5% for dysthymia, 86.9% for oppositional defiant disorder, 77.5% for school related problems, 90.9% for conduct disorder, 79.6% for anxiety and 93.5% for Attention deficit/hyperactivity disorder, also the chi square value based on Bartlett's Test was 2242.947 for dysthymia, 2239.112 for oppositional defiant disorder, 1221.917 for school work problems, 5031.511 for conduct, 1421.1 for anxiety, and 7644.122 for ADHD. Since mentioned values were larger than the chi square critical values (P<0.05), it found that the factor correlation matrix is appropriate for factor analysis. Based on the findings, we can conclude that Wender Utah rating scale can be appropriately used for predicting dysthymia, oppositional defiant disorder, school work problems, conduct disorder, anxiety, in adults with ADHD.

Phenomenological implications of the blown-up orbifolds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cvetic, M.

1987-05-01

We discuss the structure of the effective Lagrangian for the (2,2) Z/sub N/ orbifolds and the corresponding Calabi-Yau manifolds which are obtained by ''blowing-up'' the orbifold singularities. The method to ''blow-up'' such singularities is reviewed. Results are exact at the string tree-level. In particular, the question of generating an intermediate scale M/sub I/ in such models is addressed. It is shown that for Z/sub N/ orbifolds (except one) and the corresponding blown-up orbifolds which are compactified on any six-torus T/sup 6/ which can be obtained by continuously deforming T/sup 4/ circle times T/sup 2/, all the terms of the typemore » (2727)/sup K/ are absent from the effective superpotential, thus questioning the mechanism for generating a large intermediate scale for such compactifications.« less

Pilot-scale test for electron beam purification of flue gas from coal-combustion boiler

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hashimoto, Shoji; Namba, Hideki; Tokunaga, Okihiro

1995-06-01

Construction of a pilot plant of the treatment capacity of 12,000 m{sup 3}N/h flue gas was completed in November, 1992 in the Shin-Nagoya Thermal Power Station, Nagoya for electron beam purification of flue-gas from coal combustion boiler and the operation had been continued during one year. The results obtained In the tests shows that the target removal efficiency for SO{sub 2} (94 %) and for NO{sub x} (80 %) was achieved with appropriate operation conditions (electron beam dose, temperature, amount of ammonia etc.). The effective collection of powdery by-products was performed by an electrostatic precipitator.

Quantitative impedance characterization of sub-10 nm scale capacitors and tunnel junctions with an interferometric scanning microwave microscope.

PubMed

Wang, Fei; Clément, Nicolas; Ducatteau, Damien; Troadec, David; Tanbakuchi, Hassan; Legrand, Bernard; Dambrine, Gilles; Théron, Didier

2014-10-10

We present a method to characterize sub-10 nm capacitors and tunnel junctions by interferometric scanning microwave microscopy (iSMM) at 7.8 GHz. At such device scaling, the small water meniscus surrounding the iSMM tip should be reduced by proper tip tuning. Quantitative impedance characterization of attofarad range capacitors is achieved using an 'on-chip' calibration kit facing thousands of nanodevices. Nanoscale capacitors and tunnel barriers were detected through variations in the amplitude and phase of the reflected microwave signal, respectively. This study promises quantitative impedance characterization of a wide range of emerging functional nanoscale devices.

New approach for pattern collapse problem by increasing contact area at sub-100nm patterning

NASA Astrophysics Data System (ADS)

Lee, Sung-Koo; Jung, Jae Chang; Lee, Min Suk; Lee, Sung K.; Kim, Sam Young; Hwang, Young-Sun; Bok, Cheol K.; Moon, Seung-Chan; Shin, Ki S.; Kim, Sang-Jung

2003-06-01

To accomplish minimizing feature size to sub 100nm, new light sources for photolithography are emerging, such as ArF(193nm), F2(157nm), and EUV(13nm). However as the pattern size decreases to sub 100nm, a new obstacle, that is pattern collapse problem, becomes most serious bottleneck to the road for the sub 100 nm lithography. The main reason for this pattern collapse problem is capillary force that is increased as the pattern size decreases. As a result there were some trials to decrease this capillary force by changing developer or rinse materials that had low surface tension. On the other hands, there were other efforts to increase adhesion between resists and sub materials (organic BARC). In this study, we will propose a novel approach to solve pattern collapse problems by increasing contact area between sub material (organic BARC) and resist pattern. The basic concept of this approach is that if nano-scale topology is made at the sub material, the contact area between sub materials and resist will be increased. The process scheme was like this. First after coating and baking of organic BARC material, the nano-scale topology (3~10nm) was made by etching at this organic BARC material. On this nano-scale topology, resist was coated and exposed. Finally after develop, the contact area between organic BARC and resist could be increased. Though nano-scale topology was made by etching technology, this 20nm topology variation induced large substrate reflectivity of 4.2% and as a result the pattern fidelity was not so good at 100nm 1:1 island pattern. So we needed a new method to improve pattern fidelity problem. This pattern fidelity problem could be solved by introducing a sacrificial BARC layer. The process scheme was like this. First organic BARC was coated of which k value was about 0.64 and then sacrificial BARC layers was coated of which k value was about 0.18 on the organic BARC. The nano-scale topology (1~4nm) was made by etching of this sacrificial BARC layer and then as the same method mentioned above, the contact area between sacrificial layer and resist could be increased. With this introduction of sacrificial layer, the substrate reflectivity of sacrificial BARC layer was decreased enormously to 0.2% though there is 20nm topology variation of sacrificial BARC layer. With this sacrificial BARC layer, we could get 100nm 1:1 L/S pattern. With conventional process, the minimum CD where no collapse occurred, was 96.5nm. By applying this sacrificial BARC layer, the minimum CD where no collapse occurred, was 65.7nm. In conclusion, with nano-scale topology and sacrificial BARC layer, we could get very small pattern that was strong to pattern collapse issue.

Assessment of zero-equation SGS models for simulating indoor environment

NASA Astrophysics Data System (ADS)

Taghinia, Javad; Rahman, Md Mizanur; Tse, Tim K. T.

2016-12-01

The understanding of air-flow in enclosed spaces plays a key role to designing ventilation systems and indoor environment. The computational fluid dynamics aspects dictate that the large eddy simulation (LES) offers a subtle means to analyze complex flows with recirculation and streamline curvature effects, providing more robust and accurate details than those of Reynolds-averaged Navier-Stokes simulations. This work assesses the performance of two zero-equation sub-grid scale models: the Rahman-Agarwal-Siikonen-Taghinia (RAST) model with a single grid-filter and the dynamic Smagorinsky model with grid-filter and test-filter scales. This in turn allows a cross-comparison of the effect of two different LES methods in simulating indoor air-flows with forced and mixed (natural + forced) convection. A better performance against experiments is indicated with the RAST model in wall-bounded non-equilibrium indoor air-flows; this is due to its sensitivity toward both the shear and vorticity parameters.

Using Patterns of Summed Scores in Paper-and-Pencil Tests and Computer-Adaptive Tests to Detect Misfitting Item Score Patterns

ERIC Educational Resources Information Center

Meijer, Rob R.

2004-01-01

Two new methods have been proposed to determine unexpected sum scores on sub-tests (testlets) both for paper-and-pencil tests and computer adaptive tests. A method based on a conservative bound using the hypergeometric distribution, denoted p, was compared with a method where the probability for each score combination was calculated using a…

Computational Analyses in Support of Sub-scale Diffuser Testing for the A-3 Facility. Part 1; Steady Predictions

NASA Technical Reports Server (NTRS)

Allgood, Daniel C.; Graham, Jason S.; Ahuja, Vineet; Hosangadi, Ashvin

2010-01-01

Simulation technology can play an important role in rocket engine test facility design and development by assessing risks, providing analysis of dynamic pressure and thermal loads, identifying failure modes and predicting anomalous behavior of critical systems. Advanced numerical tools assume greater significance in supporting testing and design of high altitude testing facilities and plume induced testing environments of high thrust engines because of the greater inter-dependence and synergy in the functioning of the different sub-systems. This is especially true for facilities such as the proposed A-3 facility at NASA SSC because of a challenging operating envelope linked to variable throttle conditions at relatively low chamber pressures. Facility designs in this case will require a complex network of diffuser ducts, steam ejector trains, fast operating valves, cooling water systems and flow diverters that need to be characterized for steady state performance. In this paper, we will demonstrate with the use of CFD analyses s advanced capability to evaluate supersonic diffuser and steam ejector performance in a sub-scale A-3 facility at NASA Stennis Space Center (SSC) where extensive testing was performed. Furthermore, the focus in this paper relates to modeling of critical sub-systems and components used in facilities such as the A-3 facility. The work here will address deficiencies in empirical models and current CFD analyses that are used for design of supersonic diffusers/turning vanes/ejectors as well as analyses for confined plumes and venting processes. The primary areas that will be addressed are: (1) supersonic diffuser performance including analyses of thermal loads (2) accurate shock capturing in the diffuser duct; (3) effect of turning duct on the performance of the facility (4) prediction of mass flow rates and performance classification for steam ejectors (5) comparisons with test data from sub-scale diffuser testing and assessment of confidence levels in CFD based flowpath modeling of the facility. The analyses tools used here expand on the multi-element unstructured CFD which has been tailored and validated for impingement dynamics of dry plumes, complex valve/feed systems, and high pressure propellant delivery systems used in engine and component test stands at NASA SSC. The analyses performed in the evaluation of the sub-scale diffuser facility explored several important factors that influence modeling and understanding of facility operation such as (a) importance of modeling the facility with Real Gas approximation, (b) approximating the cluster of steam ejector nozzles as a single annular nozzle, (c) existence of mixed subsonic/supersonic flow downstream of the turning duct, and (d) inadequacy of two-equation turbulence models in predicting the correct pressurization in the turning duct and expansion of the second stage steam ejectors. The procedure used for modeling the facility was as follows: (i) The engine, test cell and first stage ejectors were simulated with an axisymmetric approximation (ii) the turning duct, second stage ejectors and the piping downstream of the second stage ejectors were analyzed with a three-dimensional simulation utilizing a half-plane symmetry approximation. The solution i.e. primitive variables such as pressure, velocity components, temperature and turbulence quantities were passed from the first computational domain and specified as a supersonic boundary condition for the second simulation. (iii) The third domain comprised of the exit diffuser and the region in the vicinity of the facility (primary included to get the correct shock structure at the exit of the facility and entrainment characteristics). The first set of simulations comprising the engine, test cell and first stage ejectors was carried out both as a turbulent real gas calculation as well as a turbulent perfect gas calculation. A comparison for the two cases (Real Turbulent and Perfect gas turbulent) of the Ma Number distribution and temperature distributions are shown in Figures 1 and 2 respectively.

Pharmacokinetic comparison and bioequivalence evaluation of two 10-mg baclofen formulations in healthy male subjects
.

PubMed

Yoon, Sumin; Lee, SeungHwan; Yu, Kyung-Sang; Yim, Sung-Vin; Kim, Bo-Hyung

2017-02-01

Baclofen is used as a skeletal muscle relaxant for multiple sclerosis patients. It depresses the transmission of monosynaptic and polysynaptic reflex by stimulating GABA_β (gamma-aminobutyric acid) receptors. The aim of this study was to compare the pharmacokinetic characteristics of two 10-mg baclofen formulations and to assess bioequivalence. A randomized, single-dose, two-period, two-sequence crossover study was conducted in healthy male subjects. Each subject received the test or reference formulations. After washout period, all subjects received the alternative formulation. Blood samples were collected for up to 24 hours after the dose in each period. Pharmacokinetic (PK) parameters, including t_max, C_max, and AUC_last were calculated by noncompartmental methods. The geometric mean ratio (GMR) of the test to the reference formulation and its 90% confidence interval (CI) for C_max and AUC_last were calculated for assessment of bioequivalence. A total of 22 subjects completed the study. The median t_max of the test and the reference formulation were 1.50 and 1.25 hours, respectively. The mean (± SD) C_max of the test and the reference formulation were 141.401 ± 29.447 ng/mL and 138.837 ± 31.392 ng/mL, respectively. The mean (± SD) AUC_last of the two formulations were 702.404 ± 82.149 ng×h/mL and 726.803 ± 90.638 ng×h/mL, respectively. The GMR (90% CI) of the test to the reference formulation for the C_max and AUC_last were 1.0306 (0.9564 - 1.1106) and 0.9674 (0.9437 - 0.9916), respectively. The two different baclofen 10-mg formulations had similar PK profiles and were bioequivalent based on C_max and AUC_last.
.

Modeling of diatomic molecule using the Morse potential and the Verlet algorithm

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fidiani, Elok

Performing molecular modeling usually uses special software for Molecular Dynamics (MD) such as: GROMACS, NAMD, JMOL etc. Molecular dynamics is a computational method to calculate the time dependent behavior of a molecular system. In this work, MATLAB was used as numerical method for a simple modeling of some diatomic molecules: HCl, H{sub 2} and O{sub 2}. MATLAB is a matrix based numerical software, in order to do numerical analysis, all the functions and equations describing properties of atoms and molecules must be developed manually in MATLAB. In this work, a Morse potential was generated to describe the bond interaction betweenmore » the two atoms. In order to analyze the simultaneous motion of molecules, the Verlet Algorithm derived from Newton’s Equations of Motion (classical mechanics) was operated. Both the Morse potential and the Verlet algorithm were integrated using MATLAB to derive physical properties and the trajectory of the molecules. The data computed by MATLAB is always in the form of a matrix. To visualize it, Visualized Molecular Dynamics (VMD) was performed. Such method is useful for development and testing some types of interaction on a molecular scale. Besides, this can be very helpful for describing some basic principles of molecular interaction for educational purposes.« less

Assessment of crack opening area for leak rates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sharples, J.K.; Bouchard, P.J.

1997-04-01

This paper outlines the background to recommended crack opening area solutions given in a proposed revision to leak before break guidance for the R6 procedure. Comparisons with experimental and analytical results are given for some selected cases of circumferential cracks in cylinders. It is shown that elastic models can provide satisfactory estimations of crack opening displacement (and area) but they become increasingly conservative for values of L{sub r} greater than approximately 0.4. The Dugdale small scale yielding model gives conservative estimates of crack opening displacement with increasing enhancement for L{sub r} values greater than 0.4. Further validation of the elastic-plasticmore » reference stress method for up to L{sub r} values of about 1.0 is presented by experimental and analytical comparisons. Although a more detailed method, its application gives a best estimate of crack opening displacement which may be substantially greater than small scale plasticity models. It is also shown that the local boundary conditions in pipework need to be carefully considered when evaluating crack opening area for through-wall bending stresses resulting from welding residual stresses or geometry discontinuities.« less

A Sub-ps Stability Time Transfer Method Based on Optical Modems.

PubMed

Frank, Florian; Stefani, Fabio; Tuckey, Philip; Pottie, Paul-Eric

2018-06-01

Coherent optical fiber links recently demonstrate their ability to compare the most advanced optical clocks over a continental scale. The outstanding performances of the optical clocks are stimulating the community to build much more stable time scales, and to develop the means to compare them. Optical fiber link is one solution that needs to be explored. Here, we are investigating a new method to transfer time based on an optical demodulation of a phase step imprint onto the optical carrier. We show the implementation of a proof-of-principle experiment over 86-km urban fiber, and report time interval transfer stability of 1 pulse per second signal with sub-ps resolution from 10 s to one day of measurement time. Prospects for future development and implementation in active telecommunication networks, not only regarding performance but also compatibility, conclude this paper.

A multireference perturbation method using non-orthogonal Hartree-Fock determinants for ground and excited states

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yost, Shane R.; Kowalczyk, Tim; Van Voorhis, Troy, E-mail: tvan@mit.edu

2013-11-07

In this article we propose the ΔSCF(2) framework, a multireference strategy based on second-order perturbation theory, for ground and excited electronic states. Unlike the complete active space family of methods, ΔSCF(2) employs a set of self-consistent Hartree-Fock determinants, also known as ΔSCF states. Each ΔSCF electronic state is modified by a first-order correction from Møller-Plesset perturbation theory and used to construct a Hamiltonian in a configuration interactions like framework. We present formulas for the resulting matrix elements between nonorthogonal states that scale as N{sub occ}{sup 2}N{sub virt}{sup 3}. Unlike most active space methods, ΔSCF(2) treats the ground and excited statemore » determinants even-handedly. We apply ΔSCF(2) to the H{sub 2}, hydrogen fluoride, and H{sub 4} systems and show that the method provides accurate descriptions of ground- and excited-state potential energy surfaces with no single active space containing more than 10 ΔSCF states.« less

Improved accuracy in quantitative laser-induced breakdown spectroscopy using sub-models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, Ryan B.; Clegg, Samuel M.; Frydenvang, Jens

We report that accurate quantitative analysis of diverse geologic materials is one of the primary challenges faced by the Laser-Induced Breakdown Spectroscopy (LIBS)-based ChemCam instrument on the Mars Science Laboratory (MSL) rover. The SuperCam instrument on the Mars 2020 rover, as well as other LIBS instruments developed for geochemical analysis on Earth or other planets, will face the same challenge. Consequently, part of the ChemCam science team has focused on the development of improved multivariate analysis calibrations methods. Developing a single regression model capable of accurately determining the composition of very different target materials is difficult because the response ofmore » an element’s emission lines in LIBS spectra can vary with the concentration of other elements. We demonstrate a conceptually simple “submodel” method for improving the accuracy of quantitative LIBS analysis of diverse target materials. The method is based on training several regression models on sets of targets with limited composition ranges and then “blending” these “sub-models” into a single final result. Tests of the sub-model method show improvement in test set root mean squared error of prediction (RMSEP) for almost all cases. Lastly, the sub-model method, using partial least squares regression (PLS), is being used as part of the current ChemCam quantitative calibration, but the sub-model method is applicable to any multivariate regression method and may yield similar improvements.« less

Improved accuracy in quantitative laser-induced breakdown spectroscopy using sub-models

DOE PAGES

Anderson, Ryan B.; Clegg, Samuel M.; Frydenvang, Jens; ...

2016-12-15

We report that accurate quantitative analysis of diverse geologic materials is one of the primary challenges faced by the Laser-Induced Breakdown Spectroscopy (LIBS)-based ChemCam instrument on the Mars Science Laboratory (MSL) rover. The SuperCam instrument on the Mars 2020 rover, as well as other LIBS instruments developed for geochemical analysis on Earth or other planets, will face the same challenge. Consequently, part of the ChemCam science team has focused on the development of improved multivariate analysis calibrations methods. Developing a single regression model capable of accurately determining the composition of very different target materials is difficult because the response ofmore » an element’s emission lines in LIBS spectra can vary with the concentration of other elements. We demonstrate a conceptually simple “submodel” method for improving the accuracy of quantitative LIBS analysis of diverse target materials. The method is based on training several regression models on sets of targets with limited composition ranges and then “blending” these “sub-models” into a single final result. Tests of the sub-model method show improvement in test set root mean squared error of prediction (RMSEP) for almost all cases. Lastly, the sub-model method, using partial least squares regression (PLS), is being used as part of the current ChemCam quantitative calibration, but the sub-model method is applicable to any multivariate regression method and may yield similar improvements.« less

Resistivity scaling and electron relaxation times in metallic nanowires

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moors, Kristof, E-mail: kristof@itf.fys.kuleuven.be; Imec, Kapeldreef 75, B-3001 Leuven; Sorée, Bart

2014-08-14

We study the resistivity scaling in nanometer-sized metallic wires due to surface roughness and grain-boundaries, currently the main cause of electron scattering in nanoscaled interconnects. The resistivity has been obtained with the Boltzmann transport equation, adopting the relaxation time approximation of the distribution function and the effective mass approximation for the conducting electrons. The relaxation times are calculated exactly, using Fermi's golden rule, resulting in a correct relaxation time for every sub-band state contributing to the transport. In general, the relaxation time strongly depends on the sub-band state, something that remained unclear with the methods of previous work. The resistivitymore » scaling is obtained for different roughness and grain-boundary properties, showing large differences in scaling behavior and relaxation times. Our model clearly indicates that the resistivity is dominated by grain-boundary scattering, easily surpassing the surface roughness contribution by a factor of 10.« less

Tuning the reactivity of Al/Fe{sub 2}O{sub 3} nanoenergetic materials via an approach combining soft template self-assembly with sol–gel process process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Tianfu; Wang, Zhen; Li, Guoping

2015-10-15

A bottom-up approach combining soft template self-assembly with sol–gel process, was adopted to prepare the assembled Al/Fe{sub 2}O{sub 3} nanoenergetic materials, assembly-Al/Fe{sub 2}O{sub 3} sample. The other two unassembled Al/Fe{sub 2}O{sub 3}a nanoenergetic materials, sol–gel–Al/Fe{sub 2}O{sub 3} sample and mixing-Al/Fe{sub 2}O{sub 3} sample, were prepared by sol–gel method and physical mixing method respectively. The assembly process within the preparation of the assembly-Al/Fe{sub 2}O{sub 3} sample was analyzed through the changes in the average hydrodynamic diameters of the particles and the micelles in solution. SEM, EDS and TEM tests were performed to demonstrate a significant improvement regarding to dispersity and arrangementsmore » of the Al and Fe{sub 2}O{sub 3} particles in the assembled samples, compared to that of the unassembled Al/Fe{sub 2}O{sub 3} samples. DSC test was employed to characterize the reactivity of the samples. The heat release of the assembled Al/Fe{sub 2}O{sub 3} sample was 2088 J/g, about 400 and 990 J/g more than that of the sol–gel–Al/Fe{sub 2}O{sub 3} sample and mixing-Al/Fe{sub 2}O{sub 3} sample, respectively. - Graphical abstract: Modified aluminum (Al) nanoparticles with hydrophobic surface assembled into the Brij S10 micelle in Fe(III) sol, then the well dispersed system was transformed into Al/Fe{sub 2}O{sub 3} nanoenergetic materials with high reactivity. - Highlights: • An approach combining soft template self-assembly with sol–gel process was adopted. • The aggregation of Al nanoparticles in the final product was reduced significantly. • The reactivity of Al/Fe{sub 2}O{sub 3} nanoenergetic materials was improved to a large extent.« less

Calibration of a Physically-Based Semi-Distributed Hydrologic Model: The Importance of Internal Justification

NASA Astrophysics Data System (ADS)

Tasdighi, A.; Arabi, M.

2014-12-01

Calibration of physically-based distributed hydrologic models has always been a challenging task and subject of controversy in the literature. This study is aimed to investigate how different physiographic characteristics of watersheds call for adaption of the methods used in order to have more robust and internally justifiable simulations. Haw Watershed (1300 sq. mi.) is located in the piedmont region of North Carolina draining into B. Everett Jordan Lake located in west of Raleigh. Major land covers in this watershed are forest (50%), urban/suburban (21%) and agriculture (25%) of which a large portion is pasture. Different hydrologic behaviors are observed in this watershed based on the land use composition and size of the sub-watersheds. Highly urbanized sub-watersheds show flashier hydrographs and near instantaneous hydrologic responses. This is also the case with smaller sub-watersheds with relatively lower percentage of urban areas. The Soil and Water Assessment Tool (SWAT) has been widely used in the literature for hydrologic simulation on daily basis using Soil Conservation Service Curve Number method (SCS CN). However, it has not been used as frequently using the sub-daily routines. In this regard there are a number of studies in the literature which have used coarse time scale (daily) precipitation with methods like SCS CN to calibrate SWAT for watersheds containing different types of land uses and soils reporting satisfying results at the outlet of the watershed. This is while for physically-based distributed models, the more important concern should be to check and analyze the internal processes leading to those results. In this study, the watershed is divided into several sub-watersheds to compare the performance of SCS CN and Green & Ampt (GA) methods on different land uses at different spatial scales. The results suggest better performance of GA compared to SCS CN for smaller and highly urbanized sub-watersheds although GA predominance is not very significant for the latter. Also, the better performance of GA in simulating the peak flows and flashy behavior of the hydrographs is notable. GA did not show a significant improvement over SCS CN in simulating the excess rainfall for larger sub-watersheds.

Effects of multiple-scale driving on turbulence statistics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yoo, Hyunju; Cho, Jungyeon, E-mail: hyunju527@gmail.com, E-mail: jcho@cnu.ac.kr

2014-01-01

Turbulence is ubiquitous in astrophysical fluids such as the interstellar medium and the intracluster medium. In turbulence studies, it is customary to assume that fluid is driven on a single scale. However, in astrophysical fluids, there can be many different driving mechanisms that act on different scales. If there are multiple energy-injection scales, the process of energy cascade and turbulence dynamo will be different compared with the case of the single energy-injection scale. In this work, we perform three-dimensional incompressible/compressible magnetohydrodynamic turbulence simulations. We drive turbulence in Fourier space in two wavenumber ranges, 2≤k≤√12 (large scale) and 15 ≲ kmore » ≲ 26 (small scale). We inject different amount of energy in each range by changing the amplitude of forcing in the range. We present the time evolution of the kinetic and magnetic energy densities and discuss the turbulence dynamo in the presence of energy injections at two scales. We show how kinetic, magnetic, and density spectra are affected by the two-scale energy injections and we discuss the observational implications. In the case ε {sub L} < ε {sub S}, where ε {sub L} and ε {sub S} are energy-injection rates at the large and small scales, respectively, our results show that even a tiny amount of large-scale energy injection can significantly change the properties of turbulence. On the other hand, when ε {sub L} ≳ ε {sub S}, the small-scale driving does not influence the turbulence statistics much unless ε {sub L} ∼ ε {sub S}.« less

Biomimetic synthesis of hierarchical crystalline hydroxyapatite fibers in large-scale

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xing, Chaogang; Ge, Suxiang; Huang, Baojun

Highlights: ► Crystalline hierarchical hydroxyapatite (HAp) fibers are synthesized. ► We employ a biomimetic route by using cotton cloth as a natural bio-template. ► We study the effects of pH, ultrasonic cleaning time, and calcination temperature. ► We obtain an optimized reaction condition. ► This is a low cost method for production of hierarchical HAp fibers. -- Abstract: Crystalline hierarchical hydroxyapatite [Ca{sub 10}(PO{sub 4}){sub 6}(OH){sub 2}, HAp)] fibers were successfully synthesized via a biomimetic route by using cotton cloth as a natural bio-template. The effects of pH value, aging time, ultrasonic cleaning time, and calcination temperature on the purity andmore » morphology of the resulting hydroxyapatite (HAp) were monitored by scanning election microscope (SEM), X-ray diffraction (XRD), and infrared spectrophotometer (IR) to obtain an optimized reaction condition, namely, pH 9, ultrasonic cleaning for 1 min, aging for 24 h, and calcination at 600 °C for 4 h. We found that the natural cellulose could not only control the morphology of HAp but also lower its phase transformation temperature. The impact of this method lies in its low cost and successful production of large-scale patterning of three-dimensional hierarchical HAp fibers.« less

ENHANCED PRACTICAL PHOTOSYNTHETIC CO2 MITIGATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dr. Gregory Kremer; Dr. David J. Bayless; Dr. Morgan Vis

2001-07-25

This quarterly report documents significant achievements in the Enhanced Practical Photosynthetic CO{sub 2} Mitigation project during the period from 4/03/2001 through 7/02/2001. Most of the achievements are milestones in our efforts to complete the tasks and subtasks that constitute the project objectives. Note that this version of the quarterly technical report is a revision to add the reports from subcontractors Montana State and Oak Ridge National Laboratories The significant accomplishments for this quarter include: Development of an experimental plan and initiation of experiments to create a calibration curve that correlates algal chlorophyll levels with carbon levels (to simplify future experimentalmore » procedures); Completion of debugging of the slug flow reactor system, and development of a plan for testing the pressure drop of the slug flow reactor; Design and development of a new bioreactor screen design which integrates the nutrient delivery drip system and the harvesting system; Development of an experimental setup for testing the new integrated drip system/harvesting system; Completion of model-scale bioreactor tests examining the effects of CO{sub 2} concentration levels and lighting levels on Nostoc 86-3 growth rates; Completion of the construction of a larger model-scale bioreactor to improve and expand testing capabilities and initiation of tests; Substantial progress on construction of a pilot-scale bioreactor; and Preliminary economic analysis of photobioreactor deployment. Plans for next quarter's work are included in the conclusions. A preliminary economic analysis is included as an appendix.« less

Isometric scaling of above- and below-ground biomass at the individual and community levels in the understorey of a sub-tropical forest.

PubMed

Cheng, Dongliang; Zhong, Quanlin; Niklas, Karl J; Ma, Yuzhu; Yang, Yusheng; Zhang, Jianhua

2015-02-01

Empirical studies and allometric partitioning (AP) theory indicate that plant above-ground biomass (MA) scales, on average, one-to-one (isometrically) with below-ground biomass (MR) at the level of individual trees and at the level of entire forest communities. However, the ability of the AP theory to predict the biomass allocation patterns of understorey plants has not been established because most previous empirical tests have focused on canopy tree species or very large shrubs. In order to test the AP theory further, 1586 understorey sub-tropical forest plants from 30 sites in south-east China were harvested and examined. The numerical values of the scaling exponents and normalization constants (i.e. slopes and y-intercepts, respectively) of log-log linear MA vs. MR relationships were determined for all individual plants, for each site, across the entire data set, and for data sorted into a total of 19 sub-sets of forest types and successional stages. Similar comparisons of MA/MR were also made. The data revealed that the mean MA/MR of understorey plants was 2·44 and 1·57 across all 1586 plants and for all communities, respectively, and MA scaled nearly isometrically with respect to MR, with scaling exponents of 1·01 for all individual plants and 0·99 for all communities. The scaling exponents did not differ significantly among different forest types or successional stages, but the normalization constants did, and were positively correlated with MA/MR and negatively correlated with scaling exponents across all 1586 plants. The results support the AP theory's prediction that MA scales nearly one-to-one with MR (i.e. MA ∝ MR (≈1·0)) and that plant biomass partitioning for individual plants and at the community level share a strikingly similar pattern, at least for the understorey plants examined in this study. Furthermore, variation in environmental conditions appears to affect the numerical values of normalization constants, but not the scaling exponents of the MA vs. MR relationship. This feature of the results suggests that plant size is the primary driver of the MA vs. MR biomass allocation pattern for understorey plants in sub-tropical forests. © The Author 2015. Published by Oxford University Press on behalf of the Annals of Botany Company. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Recycling inflow method for simulations of spatially evolving turbulent boundary layers over rough surfaces

NASA Astrophysics Data System (ADS)

Yang, Xiang I. A.; Meneveau, Charles

2016-01-01

The technique by Lund et al. to generate turbulent inflow for simulations of developing boundary layers over smooth flat plates is extended to the case of surfaces with roughness elements. In the Lund et al. method, turbulent velocities on a sampling plane are rescaled and recycled back to the inlet as inflow boundary condition. To rescale mean and fluctuating velocities, appropriate length scales need be identified and for smooth surfaces, the viscous scale lν = ν/uτ (where ν is the kinematic viscosity and uτ is the friction velocity) is employed for the inner layer. Different from smooth surfaces, in rough wall boundary layers the length scale of the inner layer, i.e. the roughness sub-layer scale ld, must be determined by the geometric details of the surface roughness elements and the flow around them. In the proposed approach, it is determined by diagnosing dispersive stresses that quantify the spatial inhomogeneity caused by the roughness elements in the flow. The scale ld is used for rescaling in the inner layer, and the boundary layer thickness δ is used in the outer region. Both parts are then combined for recycling using a blending function. Unlike the blending function proposed by Lund et al. which transitions from the inner layer to the outer layer at approximately 0.2δ, here the location of blending is shifted upwards to enable simulations of very rough surfaces in which the roughness length may exceed the height of 0.2δ assumed in the traditional method. The extended rescaling-recycling method is tested in large eddy simulation of flow over surfaces with various types of roughness element shapes.

A Decision Mixture Model-Based Method for Inshore Ship Detection Using High-Resolution Remote Sensing Images

PubMed Central

Bi, Fukun; Chen, Jing; Zhuang, Yin; Bian, Mingming; Zhang, Qingjun

2017-01-01

With the rapid development of optical remote sensing satellites, ship detection and identification based on large-scale remote sensing images has become a significant maritime research topic. Compared with traditional ocean-going vessel detection, inshore ship detection has received increasing attention in harbor dynamic surveillance and maritime management. However, because the harbor environment is complex, gray information and texture features between docked ships and their connected dock regions are indistinguishable, most of the popular detection methods are limited by their calculation efficiency and detection accuracy. In this paper, a novel hierarchical method that combines an efficient candidate scanning strategy and an accurate candidate identification mixture model is presented for inshore ship detection in complex harbor areas. First, in the candidate region extraction phase, an omnidirectional intersected two-dimension scanning (OITDS) strategy is designed to rapidly extract candidate regions from the land-water segmented images. In the candidate region identification phase, a decision mixture model (DMM) is proposed to identify real ships from candidate objects. Specifically, to improve the robustness regarding the diversity of ships, a deformable part model (DPM) was employed to train a key part sub-model and a whole ship sub-model. Furthermore, to improve the identification accuracy, a surrounding correlation context sub-model is built. Finally, to increase the accuracy of candidate region identification, these three sub-models are integrated into the proposed DMM. Experiments were performed on numerous large-scale harbor remote sensing images, and the results showed that the proposed method has high detection accuracy and rapid computational efficiency. PMID:28640236

A Decision Mixture Model-Based Method for Inshore Ship Detection Using High-Resolution Remote Sensing Images.

PubMed

Bi, Fukun; Chen, Jing; Zhuang, Yin; Bian, Mingming; Zhang, Qingjun

2017-06-22

With the rapid development of optical remote sensing satellites, ship detection and identification based on large-scale remote sensing images has become a significant maritime research topic. Compared with traditional ocean-going vessel detection, inshore ship detection has received increasing attention in harbor dynamic surveillance and maritime management. However, because the harbor environment is complex, gray information and texture features between docked ships and their connected dock regions are indistinguishable, most of the popular detection methods are limited by their calculation efficiency and detection accuracy. In this paper, a novel hierarchical method that combines an efficient candidate scanning strategy and an accurate candidate identification mixture model is presented for inshore ship detection in complex harbor areas. First, in the candidate region extraction phase, an omnidirectional intersected two-dimension scanning (OITDS) strategy is designed to rapidly extract candidate regions from the land-water segmented images. In the candidate region identification phase, a decision mixture model (DMM) is proposed to identify real ships from candidate objects. Specifically, to improve the robustness regarding the diversity of ships, a deformable part model (DPM) was employed to train a key part sub-model and a whole ship sub-model. Furthermore, to improve the identification accuracy, a surrounding correlation context sub-model is built. Finally, to increase the accuracy of candidate region identification, these three sub-models are integrated into the proposed DMM. Experiments were performed on numerous large-scale harbor remote sensing images, and the results showed that the proposed method has high detection accuracy and rapid computational efficiency.

Agreement between clinicians' and care givers' assessment of intelligence in Nigerian children with intellectual disability: 'ratio IQ' as a viable option in the absence of standardized 'deviance IQ' tests in sub-Saharan Africa

PubMed Central

Bakare, Muideen O; Ubochi, Vincent N; Okoroikpa, Ifeoma N; Aguocha, Chinyere M; Ebigbo, Peter O

2009-01-01

Background There may be need to assess intelligent quotient (IQ) scores in sub-Saharan African children with intellectual disability, either for the purpose of educational needs assessment or research. However, modern intelligence scales developed in the western parts of the world suffer limitation of widespread use because of the influence of socio-cultural variations across the world. This study examined the agreement between IQ scores estimation among Nigerian children with intellectual disability using clinicians' judgment based on International Classification of Diseases, tenth Edition (ICD - 10) criteria for mental retardation and caregivers judgment based on 'ratio IQ' scores calculated from estimated mental age in the context of socio-cultural milieu of the children. It proposed a viable option of IQ score assessment among sub-Saharan African children with intellectual disability, using a ratio of culture-specific estimated mental age and chronological age of the child in the absence of standardized alternatives, borne out of great diversity in socio-cultural context of sub-Saharan Africa. Methods Clinicians and care-givers independently assessed the children in relation to their socio-cultural background. Clinicians assessed the IQ scores of the children based on the ICD - 10 diagnostic criteria for mental retardation. 'Ratio IQ' scores were calculated from the ratio of estimated mental age and chronological age of each child. The IQ scores as assessed by the clinicians were then compared with the 'ratio IQ' scores using correlation statistics. Results A total of forty-four (44) children with intellectual disability were assessed. There was a significant correlation between clinicians' assessed IQ scores and the 'ratio IQ' scores employing zero order correlation without controlling for the chronological age of the children (r = 0.47, df = 42, p = 0.001). First order correlation controlling for the chronological age of the children showed higher correlation score between clinicians' assessed IQ scores and 'ratio IQ' scores (r = 0.75, df = 41, p = 0.000). Conclusion Agreement between clinicians' assessed IQ scores and 'ratio IQ' scores was good. 'Ratio IQ' test would provide a viable option of assessing IQ scores in sub-Saharan African children with intellectual disability in the absence of culture-appropriate standardized intelligence scales, which is often the case because of great diversity in socio-cultural structures of sub-Saharan Africa. PMID:19754953

Heat transfer to small horizontal cylinders immersed in a fluidized bed

DOE Office of Scientific and Technical Information (OSTI.GOV)

Friedman, J.; Koundakjian, P.; Naylor, D.

2006-10-15

Heat transfer to horizontal cylinders immersed in fluidized beds has been extensively studied, but mainly in the context of heat transfer to boiler tubes in coal-fired beds. As a result, most correlations in the literature have been derived for cylinders of 25-50 mm diameter in vigorously fluidizing beds. In recent years, fluidized bed heat treating furnaces fired by natural gas have become increasingly popular, particularly in the steel wire manufacturing industry. These fluidized beds typically operate at relatively low fluidizing rates and with small diameter wires (1-6 mm). Nusselt number correlations developed based on boiler tube studies do not extrapolatemore » down to these small size ranges and low fluidizing rates. In order to obtain reliable Nusselt number data for these size ranges, an experimental investigation has been undertaken using two heat treating fluidized beds; one a pilot-scale industrial unit and the other a lab-scale (300 mm diameter) unit. Heat transfer measurements were obtained using resistively heated cylindrical samples ranging from 1.3 to 9.5 mm in diameter at fluidizing rates ranging from approximately 0.5 x G{sub mf} (packed bed condition) to over 10 x G{sub mf} using aluminum oxide sand particles ranging from d{sub p}=145-330 {mu}m (50-90 grit). It has been found that for all cylinder sizes tested, the Nusselt number reaches a maximum near 2 x G{sub mf}, then remains relatively steady ({+-}5-10%) to the maximum fluidizing rate tested, typically 8-12xG{sub mf}. A correlation for maximum Nusselt number is developed.« less

MID Plot: a new lithology technique. [Matrix identification plot

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clavier, C.; Rust, D.H.

1976-01-01

Lithology interpretation by the Litho-Porosity (M-N) method has been used for years, but is evidently too cumbersome and ambiguous for widespread acceptance as a field technique. To set aside these objections, another method has been devised. Instead of the log-derived parameters M and N, the MID Plot uses quasi-physical quantities, (rho/sub ma/)/sub a/ and (..delta..t/sub ma/)/sub a/, as its porosity-independent variables. These parameters, taken from suitably scaled Neutron-Density and Sonic-Neutron crossplots, define a unique matrix mineral or mixture for each point on the logs. The matrix points on the MID Plot thus remain constant in spite of changes in mudmore » filtrate, porosity, or neutron tool types (all of which significantly affect the M-N Plot). This new development is expected to bring welcome relief in areas where lithology identification is a routine part of log analysis.« less

An Investigation to Manufacturing Analytical Services Composition using the Analytical Target Cascading Method.

PubMed

Tien, Kai-Wen; Kulvatunyou, Boonserm; Jung, Kiwook; Prabhu, Vittaldas

2017-01-01

As cloud computing is increasingly adopted, the trend is to offer software functions as modular services and compose them into larger, more meaningful ones. The trend is attractive to analytical problems in the manufacturing system design and performance improvement domain because 1) finding a global optimization for the system is a complex problem; and 2) sub-problems are typically compartmentalized by the organizational structure. However, solving sub-problems by independent services can result in a sub-optimal solution at the system level. This paper investigates the technique called Analytical Target Cascading (ATC) to coordinate the optimization of loosely-coupled sub-problems, each may be modularly formulated by differing departments and be solved by modular analytical services. The result demonstrates that ATC is a promising method in that it offers system-level optimal solutions that can scale up by exploiting distributed and modular executions while allowing easier management of the problem formulation.

Top Quark Mass Measurement in the Lepton + Jets Channel Using a Matrix Element Method and \\textit{in situ} Jet Energy Calibration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aaltonen, T.; /Helsinki Inst. of Phys.; Alvarez Gonzalez, B.

A precision measurement of the top quark mass m{sub t} is obtained using a sample of t{bar t} events from p{bar p} collisions at the Fermilab Tevatron with the CDF II detector. Selected events require an electron or muon, large missing transverse energy, and exactly four high-energy jets, at least one of which is tagged as coming from a b quark. A likelihood is calculated using a matrix element method with quasi-Monte Carlo integration taking into account finite detector resolution and jet mass effects. The event likelihood is a function of m{sub t} and a parameter {Delta}{sub JES} used tomore » calibrate the jet energy scale in situ. Using a total of 1087 events, a value of m{sub t} = 173.0 {+-} 1.2 GeV/c{sup 2} is measured.« less

Top Quark Mass Measurement in the lepton+jets Channel Using a Matrix Element Method and in situ Jet Energy Calibration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aaltonen, T.; Brucken, E.; Devoto, F.

A precision measurement of the top quark mass m{sub t} is obtained using a sample of tt events from pp collisions at the Fermilab Tevatron with the CDF II detector. Selected events require an electron or muon, large missing transverse energy, and exactly four high-energy jets, at least one of which is tagged as coming from a b quark. A likelihood is calculated using a matrix element method with quasi-Monte Carlo integration taking into account finite detector resolution and jet mass effects. The event likelihood is a function of m{sub t} and a parameter {Delta}{sub JES} used to calibrate themore » jet energy scale in situ. Using a total of 1087 events in 5.6 fb{sup -1} of integrated luminosity, a value of m{sub t}=173.0{+-}1.2 GeV/c{sup 2} is measured.« less

Method and system for pattern analysis using a coarse-coded neural network

NASA Technical Reports Server (NTRS)

Spirkovska, Liljana (Inventor); Reid, Max B. (Inventor)

1994-01-01

A method and system for performing pattern analysis with a neural network coarse-coding a pattern to be analyzed so as to form a plurality of sub-patterns collectively defined by data. Each of the sub-patterns comprises sets of pattern data. The neural network includes a plurality fields, each field being associated with one of the sub-patterns so as to receive the sub-pattern data therefrom. Training and testing by the neural network then proceeds in the usual way, with one modification: the transfer function thresholds the value obtained from summing the weighted products of each field over all sub-patterns associated with each pattern being analyzed by the system.

Super-resolution for asymmetric resolution of FIB-SEM 3D imaging using AI with deep learning.

PubMed

Hagita, Katsumi; Higuchi, Takeshi; Jinnai, Hiroshi

2018-04-12

Scanning electron microscopy equipped with a focused ion beam (FIB-SEM) is a promising three-dimensional (3D) imaging technique for nano- and meso-scale morphologies. In FIB-SEM, the specimen surface is stripped by an ion beam and imaged by an SEM installed orthogonally to the FIB. The lateral resolution is governed by the SEM, while the depth resolution, i.e., the FIB milling direction, is determined by the thickness of the stripped thin layer. In most cases, the lateral resolution is superior to the depth resolution; hence, asymmetric resolution is generated in the 3D image. Here, we propose a new approach based on an image-processing or deep-learning-based method for super-resolution of 3D images with such asymmetric resolution, so as to restore the depth resolution to achieve symmetric resolution. The deep-learning-based method learns from high-resolution sub-images obtained via SEM and recovers low-resolution sub-images parallel to the FIB milling direction. The 3D morphologies of polymeric nano-composites are used as test images, which are subjected to the deep-learning-based method as well as conventional methods. We find that the former yields superior restoration, particularly as the asymmetric resolution is increased. Our super-resolution approach for images having asymmetric resolution enables observation time reduction.

Stochastic Order Redshift Technique (SORT): a simple, efficient and robust method to improve cosmological redshift measurements

NASA Astrophysics Data System (ADS)

Tejos, Nicolas; Rodríguez-Puebla, Aldo; Primack, Joel R.

2018-01-01

We present a simple, efficient and robust approach to improve cosmological redshift measurements. The method is based on the presence of a reference sample for which a precise redshift number distribution (dN/dz) can be obtained for different pencil-beam-like sub-volumes within the original survey. For each sub-volume we then impose that: (i) the redshift number distribution of the uncertain redshift measurements matches the reference dN/dz corrected by their selection functions and (ii) the rank order in redshift of the original ensemble of uncertain measurements is preserved. The latter step is motivated by the fact that random variables drawn from Gaussian probability density functions (PDFs) of different means and arbitrarily large standard deviations satisfy stochastic ordering. We then repeat this simple algorithm for multiple arbitrary pencil-beam-like overlapping sub-volumes; in this manner, each uncertain measurement has multiple (non-independent) 'recovered' redshifts which can be used to estimate a new redshift PDF. We refer to this method as the Stochastic Order Redshift Technique (SORT). We have used a state-of-the-art N-body simulation to test the performance of SORT under simple assumptions and found that it can improve the quality of cosmological redshifts in a robust and efficient manner. Particularly, SORT redshifts (zsort) are able to recover the distinctive features of the so-called 'cosmic web' and can provide unbiased measurement of the two-point correlation function on scales ≳4 h-1Mpc. Given its simplicity, we envision that a method like SORT can be incorporated into more sophisticated algorithms aimed to exploit the full potential of large extragalactic photometric surveys.

Afterbody External Aerodynamic and Performance Prediction at High Reynolds Numbers

NASA Technical Reports Server (NTRS)

Carlson, John R.

1999-01-01

This CFD experiment concludes that the potential difference between the flow between a flight Reynolds number test and a sub-scale wind tunnel test are substantial for this particular nozzle boattail geometry. The early study was performed using a linear k-epsilon turbulence model. The present study was performed using the Girimaji formulation of a algebraic Reynolds stress turbulent simulation.

Instrumentation Development for Large Scale Hypersonic Inflatable Aerodynamic Decelerator Characterization

NASA Technical Reports Server (NTRS)

Swanson, Gregory T.; Cassell, Alan M.

2011-01-01

Hypersonic Inflatable Aerodynamic Decelerator (HIAD) technology is currently being considered for multiple atmospheric entry applications as the limitations of traditional entry vehicles have been reached. The Inflatable Re-entry Vehicle Experiment (IRVE) has successfully demonstrated this technology as a viable candidate with a 3.0 m diameter vehicle sub-orbital flight. To further this technology, large scale HIADs (6.0 8.5 m) must be developed and tested. To characterize the performance of large scale HIAD technology new instrumentation concepts must be developed to accommodate the flexible nature inflatable aeroshell. Many of the concepts that are under consideration for the HIAD FY12 subsonic wind tunnel test series are discussed below.

GW quasiparticle energy study of ternary tetradymite Bi{sub 2}Te{sub 2}Se and Bi{sub 2}Te{sub 2}S thin films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shuaibu, Alhassan; Department of Physics, Faculty of Science, Nigerian Defence Academy, P.M., 2109. Kaduna Nigeria; Rahman, Md. Mahmudur

In this work, we have evaluated the quasiparticle energies of ternary tetradymite Bi{sub 2}Te{sub 2}Se and Bi{sub 2}Te{sub 2}S using first-principles calculation within the G{sub 0}W{sub 0} methods. We have also performed a broad convergence tests in order to investigate the quasiparticle corrections to the structural parameters and to the semi core d electrons in both of the compounds. For each case, we have calculated the many-body corrections within a one-shot GW method of the compounds. Our results have shown that for Bi{sub 2}Te{sub 2}Se the GW corrections increase the band gap to almost 10%, and for specific atomic positions,more » the band structure shows a close value to the experimental one. For Bi{sub 2}Te{sub 2}S, despite increase in the band gap due to the GW corrections, possibility of bulk resistivity that can be significant for photovoltaic applications was observed.« less

Kic size effect study on two high-strength steels using notched bend specimens

NASA Technical Reports Server (NTRS)

Stonesifer, F. R.

1974-01-01

Five methods are used to calculate plane strain fracture toughness (K sub Q) values for bend-specimens of various sizes from two high-strength steels. None of the methods appeared to satisfactorily predict valid stress intensity factor (K sub IC) values from specimens of sizes well below that required by E399 standard tests.

A priori testing of subgrid-scale models for the velocity-pressure and vorticity-velocity formulations

NASA Technical Reports Server (NTRS)

Winckelmans, G. S.; Lund, T. S.; Carati, D.; Wray, A. A.

1996-01-01

Subgrid-scale models for Large Eddy Simulation (LES) in both the velocity-pressure and the vorticity-velocity formulations were evaluated and compared in a priori tests using spectral Direct Numerical Simulation (DNS) databases of isotropic turbulence: 128(exp 3) DNS of forced turbulence (Re(sub(lambda))=95.8) filtered, using the sharp cutoff filter, to both 32(exp 3) and 16(exp 3) synthetic LES fields; 512(exp 3) DNS of decaying turbulence (Re(sub(Lambda))=63.5) filtered to both 64(exp 3) and 32(exp 3) LES fields. Gaussian and top-hat filters were also used with the 128(exp 3) database. Different LES models were evaluated for each formulation: eddy-viscosity models, hyper eddy-viscosity models, mixed models, and scale-similarity models. Correlations between exact versus modeled subgrid-scale quantities were measured at three levels: tensor (traceless), vector (solenoidal 'force'), and scalar (dissipation) levels, and for both cases of uniform and variable coefficient(s). Different choices for the 1/T scaling appearing in the eddy-viscosity were also evaluated. It was found that the models for the vorticity-velocity formulation produce higher correlations with the filtered DNS data than their counterpart in the velocity-pressure formulation. It was also found that the hyper eddy-viscosity model performs better than the eddy viscosity model, in both formulations.

Factoring quality laboratory diagnosis into the malaria control agenda for sub-Saharan Africa.

PubMed

Aidoo, Michael

2013-09-01

Recent progress in malaria control in sub-Saharan Africa has been achieved primarily through provision of insecticide-treated nets, indoor residual spraying, and antimalarial drugs. Although these interventions are important, proper case identification and accurate measurement of their impact depend on quality diagnostic testing. Current availability of diagnostic testing for malaria in sub-Saharan Africa is inadequate to support disease management, prevention programs, and surveillance needs. Challenges faced include a dearth of skilled workforce, inadequate health systems infrastructure, and lack of political will. A coordinated approach to providing pre-service clinical and laboratory training together with systems that support a scale-up of laboratory services could provide means not only for effective malaria case management but also, management of non-malaria febrile illnesses, disease surveillance, and accurate control program evaluation. A synthesis of the challenges faced in ensuring quality malaria testing and how to include this information in the malaria control and elimination agenda are presented.

Application of damage tolerance methodology in certification of the Piaggio P-180 Avanti

NASA Technical Reports Server (NTRS)

Johnson, Jerry

1992-01-01

The Piaggio P-180 Avanti, a twin pusher-prop engine nine-passenger business aircraft was certified in 1990, to the requirements of FAR Part 23 and Associated Special Conditions for Composite Structure. Certification included the application of a damage tolerant methodology to the design of the composite forward wing and empennage (vertical fin, horizontal stabilizer, tailcone, and rudder) structure. This methodology included an extensive analytical evaluation coupled with sub-component and full-scale testing of the structure. The work from the Damage Tolerance Analysis Assessment was incorporated into the full-scale testing. Damage representing hazards such as dropped tools, ground equipment, handling, and runway debris, was applied to the test articles. Additional substantiation included allowing manufacturing discrepancies to exist unrepaired on the full-scale articles and simulated bondline failures in critical elements. The importance of full-scale testing in the critical environmental conditions and the application of critical damage are addressed. The implication of damage tolerance on static and fatigue testing is discussed. Good correlation between finite element solutions and experimental test data was observed.

X-48C Flies Over Intersecting Runways

NASA Image and Video Library

2013-02-28

The X-48C Hybrid Wing Body research aircraft flew over the intersection of several runways adjacent to the compass rose on Rogers Dry Lake at Edwards Air Force Base during one of the sub-scale aircraft's final test flights on Feb. 28, 2013.

Scale factor measure method without turntable for angular rate gyroscope

NASA Astrophysics Data System (ADS)

Qi, Fangyi; Han, Xuefei; Yao, Yanqing; Xiong, Yuting; Huang, Yuqiong; Wang, Hua

2018-03-01

In this paper, a scale factor test method without turntable is originally designed for the angular rate gyroscope. A test system which consists of test device, data acquisition circuit and data processing software based on Labview platform is designed. Taking advantage of gyroscope's sensitivity of angular rate, a gyroscope with known scale factor, serves as a standard gyroscope. The standard gyroscope is installed on the test device together with a measured gyroscope. By shaking the test device around its edge which is parallel to the input axis of gyroscope, the scale factor of the measured gyroscope can be obtained in real time by the data processing software. This test method is fast. It helps test system miniaturized, easy to carry or move. Measure quarts MEMS gyroscope's scale factor multi-times by this method, the difference is less than 0.2%. Compare with testing by turntable, the scale factor difference is less than 1%. The accuracy and repeatability of the test system seems good.

Environmental effects on aluminum fracture

NASA Technical Reports Server (NTRS)

Schwartzberg, F. R.; Shepic, J. A.

1976-01-01

The sustained load stress corrosion cracking (SCC) threshold for aluminum alloy 214 was determined using smooth (sigma sub TH) and precracked (K sub ISCC) specimens, and cyclic load growth behavior in 3.5% NaCl salt solution was studied. The relationship between K sub ISCC and sigma sub TH was also studied. The work showed that 2124-T851 aluminum alloy in plate gage has a moderately high resistance to stress corrosion attack. Experimental results showed that no SCC occurred in the longitudinal and long transverse directions in any of the tests. Some SCC was found by smooth tests in the short transverse direction, and the data were confirmed by two test methods-sigma sub TH = 275 MN/sq m (40 ksi). No SCC was found from compact specimen tests in any direction: surface flaw and center notch specimens evaluated in the short transverse direction exhibited SCC. The data indicate that stress corrosion behavior is defect, size, and stress dependent, but not entirely in accordance with a stress intensity controlled mechanism.

An instrument to assess the statistical intensity of medical research papers.

PubMed

Nieminen, Pentti; Virtanen, Jorma I; Vähänikkilä, Hannu

2017-01-01

There is widespread evidence that statistical methods play an important role in original research articles, especially in medical research. The evaluation of statistical methods and reporting in journals suffers from a lack of standardized methods for assessing the use of statistics. The objective of this study was to develop and evaluate an instrument to assess the statistical intensity in research articles in a standardized way. A checklist-type measure scale was developed by selecting and refining items from previous reports about the statistical contents of medical journal articles and from published guidelines for statistical reporting. A total of 840 original medical research articles that were published between 2007-2015 in 16 journals were evaluated to test the scoring instrument. The total sum of all items was used to assess the intensity between sub-fields and journals. Inter-rater agreement was examined using a random sample of 40 articles. Four raters read and evaluated the selected articles using the developed instrument. The scale consisted of 66 items. The total summary score adequately discriminated between research articles according to their study design characteristics. The new instrument could also discriminate between journals according to their statistical intensity. The inter-observer agreement measured by the ICC was 0.88 between all four raters. Individual item analysis showed very high agreement between the rater pairs, the percentage agreement ranged from 91.7% to 95.2%. A reliable and applicable instrument for evaluating the statistical intensity in research papers was developed. It is a helpful tool for comparing the statistical intensity between sub-fields and journals. The novel instrument may be applied in manuscript peer review to identify papers in need of additional statistical review.

Bayesian Model for Matching the Radiometric Measurements of Aerospace and Field Ocean Color Sensors

PubMed Central

Salama, Mhd. Suhyb; Su, Zhongbo

2010-01-01

A Bayesian model is developed to match aerospace ocean color observation to field measurements and derive the spatial variability of match-up sites. The performance of the model is tested against populations of synthesized spectra and full and reduced resolutions of MERIS data. The model derived the scale difference between synthesized satellite pixel and point measurements with R2 > 0.88 and relative error < 21% in the spectral range from 400 nm to 695 nm. The sub-pixel variabilities of reduced resolution MERIS image are derived with less than 12% of relative errors in heterogeneous region. The method is generic and applicable to different sensors. PMID:22163615

DOE Office of Scientific and Technical Information (OSTI.GOV)

Won, Jong-Pil, E-mail: jpwon@konkuk.ac.kr; Hwang, Un-Jong; Lee, Su-Jin

This study evaluated the performance of shotcrete using high strength C{sub 12}A{sub 7} mineral-based accelerator that has been developed to improve the durability and long-term strength. Rebound, compressive strength and flexural strength were tested in the field. Test result showed that existing C{sub 12}A{sub 7} mineral-based accelerator exhibits better early strength than the high-strength C{sub 12}A{sub 7} mineral-based accelerator until the early age, but high-strength C{sub 12}A{sub 7} mineral-based accelerator shows about 29% higher at the long-term age of 28 days. Microstructural analysis such as scanning electron microscope (SEM), X-ray diffraction (XRD) and nitrogen adsorption method was evaluated to analyzemore » long-term strength development mechanism of high strength C{sub 12}A{sub 7} mineral-based accelerator. As analysis result, it had more dense structure due to the reaction product by adding material that used to enhanced strength. It had better resistance performance in chloride ion penetration, freezing–thawing and carbonation than shotcrete that used existing C{sub 12}A{sub 7} mineral-based accelerator.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wen, Zhigang, E-mail: xh168688@126.com; State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083; Department of Chemistry and Chemical Engineering, Qiannan Normal College for Nationalities, Duyun 558000

SnO{sub 2} nanorod bundles were synthesized by hydrothermal method. Field-emission scanning electron microscopy and transmission electron microscopy images showed that the as-prepared flowerlike SnO{sub 2} nanorod bundles consist of tetragonal nanorods with size readily tunable. Their electrochemical properties and application as anode for lithium-ion battery were evaluated by galvanostatic discharge–charge testing and cycle voltammetry. SnO{sub 2} nanorod flowers possess improved discharge capacity of 694 mA h g{sup −1} up to 40th cycle at 0.1 C. - Highlights: ► The flowerlike SnO{sub 2} nanorod bundles were synthesized by hydrothermal method. ► SnO{sub 2} nanorod bundles with tunable size by controlling concentrationmore » of SnCl{sub 4}. ► A probable formation mechanism of SnO{sub 2} nanorod bundles has been proposed.« less

Early or delayed provision of an ankle-foot orthosis in patients with acute and subacute stroke: a randomized controlled trial.

PubMed

Nikamp, Corien Dm; Buurke, Jaap H; van der Palen, Job; Hermens, Hermie J; Rietman, Johan S

2017-06-01

(1) To study the effects of providing ankle-foot orthoses in subjects with (sub)acute stroke; and (2) to study whether the point in time at which an ankle-foot orthosis is provided post-stroke (early or delayed) influences these effects. Randomized controlled trial. Rehabilitation centre. Unilateral hemiparetic stroke subjects with indication for use of an ankle-foot orthosis and maximal six weeks post-stroke. Subjects were randomly assigned to: early provision (at inclusion; Week 1) or delayed provision (eight weeks later; Week 9). 10-metre walk test, 6-minute walk test, Timed Up and Go Test, stairs test, Functional Ambulation Categories, Berg Balance Scale, Rivermead Mobility Index and Barthel Index; assessed in Weeks 1, 3, 9 and 11. A total of 33 subjects were randomized (16 early, 17 delayed). Positive effects of ankle-foot orthoses were found two weeks after provision, both when provided early (significant effects on all outcomes) or delayed (Berg Balance Scale p = 0.011, Functional Ambulation Categories p = 0.008, 6-minute walk test p = 0.005, Timed Up and Go Test p = 0.028). Comparing effects after early and delayed provision showed that early provision resulted in increased levels of improvement on Berg Balance Scale (+5.1 points, p = 0.002), Barthel Index (+1.9 points, p = 0.002) and non-significant improvements on 10-metre walk test (+0.14 m/s, p = 0.093) and Timed Up and Go Test (-5.4 seconds, p = 0.087), compared with delayed provision. We found positive effects of providing ankle-foot orthoses in (sub)acute stroke subjects that had not used these orthoses before.

Determining the Appropriateness of the "What If" Situations Test (WIST) with Turkish Pre-Schoolers.

PubMed

Citak Tunc, Gulseren; Gorak, Gulay; Ozyazicioglu, Nurcan; Ak, Bedriye; Isil, Ozlem; Vural, Pinar

2018-04-01

Measurement instruments are needed to assess the child's sexual abuse prevention program. The purpose of the study was to determine the reliability and validity of the WIST (What If Situations Test) for Turkish culture. Participants were children of the 3-6 age group attending pre-school education institutions and the sample size was identified by means of a power analysis. Seventy children were identified as the sample with 0.85 power and 0.05 type I error according to the power analysis. Language validity, content validity, internal validity coefficient (Cronbach alpha coefficient), and test-retest analyses were conducted in terms of validity and reliability in the scope of efforts for adaptation to Turkish culture. Firstly, Kendall W = 0.83 was the score for the expert opinions concerning the content validity of the language validity scale. It was found that the Cronbach alpha coefficients were between 0.68 and 0.90 for the scale sub-dimensions of appropriate and inappropriate recognition, saying, doing, telling, and reporting. The test-retest reliability of the scale was found to be r = 0.89 and the test-retest reliabilities for the sub-dimensions (appropriate recognition, inappropriate recognition, say skills, do skills, tell skills, and reporting skills) were between r = 0.48 and r = 0.92. The test-retest reliability for the Personal Safety Questionnaire (PSQ), as having complimentary items to the WIST, was found to be r = 0.82. The reliability and validity analysis of the 'What If' Situations Test (WIST), used to evaluate pre-schoolers' skills regarding self-protection against sexual abuse, showed that the Test's adaptation to Turkish culture was reliable and valid.

Unsupported palladium alloy membranes and methods of making same

DOEpatents

Way, J. Douglas; Thoen, Paul; Gade, Sabina K.

2015-06-02

The invention provides support-free palladium membranes and methods of making these membranes. Single-gas testing of the unsupported foils produced hydrogen permeabilities equivalent to thicker membranes produced by cold-rolling. Defect-free films as thin as 7.2 microns can be fabricated, with ideal H.sub.2/N.sub.2 selectivities as high as 40,000. Homogeneous membrane compositions may also be produced using these methods.

Sub-Volumetric Classification and Visualization of Emphysema Using a Multi-Threshold Method and Neural Network

NASA Astrophysics Data System (ADS)

Tan, Kok Liang; Tanaka, Toshiyuki; Nakamura, Hidetoshi; Shirahata, Toru; Sugiura, Hiroaki

Chronic Obstructive Pulmonary Disease is a disease in which the airways and tiny air sacs (alveoli) inside the lung are partially obstructed or destroyed. Emphysema is what occurs as more and more of the walls between air sacs get destroyed. The goal of this paper is to produce a more practical emphysema-quantification algorithm that has higher correlation with the parameters of pulmonary function tests compared to classical methods. The use of the threshold range from approximately -900 Hounsfield Unit to -990 Hounsfield Unit for extracting emphysema from CT has been reported in many papers. From our experiments, we realize that a threshold which is optimal for a particular CT data set might not be optimal for other CT data sets due to the subtle radiographic variations in the CT images. Consequently, we propose a multi-threshold method that utilizes ten thresholds between and including -900 Hounsfield Unit and -990 Hounsfield Unit for identifying the different potential emphysematous regions in the lung. Subsequently, we divide the lung into eight sub-volumes. From each sub-volume, we calculate the ratio of the voxels with the intensity below a certain threshold. The respective ratios of the voxels below the ten thresholds are employed as the features for classifying the sub-volumes into four emphysema severity classes. Neural network is used as the classifier. The neural network is trained using 80 training sub-volumes. The performance of the classifier is assessed by classifying 248 test sub-volumes of the lung obtained from 31 subjects. Actual diagnoses of the sub-volumes are hand-annotated and consensus-classified by radiologists. The four-class classification accuracy of the proposed method is 89.82%. The sub-volumetric classification results produced in this study encompass not only the information of emphysema severity but also the distribution of emphysema severity from the top to the bottom of the lung. We hypothesize that besides emphysema severity, the distribution of emphysema severity in the lung also plays an important role in the assessment of the overall functionality of the lung. We confirm our hypothesis by showing that the proposed sub-volumetric classification results correlate with the parameters of pulmonary function tests better than classical methods. We also visualize emphysema using a technique called the transparent lung model.

Effect of recirculation on organic matter removal in a hybrid constructed wetland system.

PubMed

Ayaz, S C; Findik, N; Akça, L; Erdoğan, N; Kinaci, C

2011-01-01

This research project aimed to determine the technologically feasible and applicable wastewater treatment systems which will be constructed to solve environmental problems caused by small communities in Turkey. Pilot-scale treatment of a small community's wastewater was performed over a period of more than 2 years in order to show applicability of these systems. The present study involves removal of organic matter and suspended solids in serially operated horizontal (HFCW) and vertical (VFCW) sub-surface flow constructed wetlands. The pilot-scale wetland was constructed downstream of anaerobic reactors at the campus of TUBITAK-MRC. Anaerobically pretreated wastewater was introduced into this hybrid two-stage sub-surface flow wetland system (TSCW). Wastewater was first introduced into the horizontal sub-surface flow system and then the vertical flow system before being discharged. Recirculation of the effluent was tested in the system. When the recirculation ratio was 100%, average removal efficiencies for TSCW were 91 +/- 4% for COD, 83 +/- 10% for BOD and 96 +/- 3% for suspended solids with average effluent concentrations of 9 +/- 5 mg/L COD, 6 +/- 3 mg/L BOD and 1 mg/L for suspended solids. Comparing non-recirculation and recirculation periods, the lowest effluent concentrations were obtained with a 100% recirculation ratio. The effluent concentrations met the Turkish regulations for discharge limits of COD, BOD and TSS in each case. The study showed that a hybrid constructed wetland system with recirculation is a very effective method of obtaining very low effluent organic matter and suspended solids concentrations downstream of anaerobic pretreatment of domestic wastewaters in small communities.

Simplified galaxy formation with mesh-less hydrodynamics

NASA Astrophysics Data System (ADS)

Lupi, Alessandro; Volonteri, Marta; Silk, Joseph

2017-09-01

Numerical simulations have become a necessary tool to describe the complex interactions among the different processes involved in galaxy formation and evolution, unfeasible via an analytic approach. The last decade has seen a great effort by the scientific community in improving the sub-grid physics modelling and the numerical techniques used to make numerical simulations more predictive. Although the recently publicly available code gizmo has proven to be successful in reproducing galaxy properties when coupled with the model of the MUFASA simulations and the more sophisticated prescriptions of the Feedback In Realistic Environment (FIRE) set-up, it has not been tested yet using delayed cooling supernova feedback, which still represent a reasonable approach for large cosmological simulations, for which detailed sub-grid models are prohibitive. In order to limit the computational cost and to be able to resolve the disc structure in the galaxies we perform a suite of zoom-in cosmological simulations with rather low resolution centred around a sub-L* galaxy with a halo mass of 3 × 1011 M⊙ at z = 0, to investigate the ability of this simple model, coupled with the new hydrodynamic method of gizmo, to reproduce observed galaxy scaling relations (stellar to halo mass, stellar and baryonic Tully-Fisher, stellar mass-metallicity and mass-size). We find that the results are in good agreement with the main scaling relations, except for the total stellar mass, larger than that predicted by the abundance matching technique, and the effective sizes for the most massive galaxies in the sample, which are too small.

Tailoring vocabularies for NLP in sub-domains: a method to detect unused word sense.

PubMed

Figueroa, Rosa L; Zeng-Treitler, Qing; Goryachev, Sergey; Wiechmann, Eduardo P

2009-11-14

We developed a method to help tailor a comprehensive vocabulary system (e.g. the UMLS) for a sub-domain (e.g. clinical reports) in support of natural language processing (NLP). The method detects unused sense in a sub-domain by comparing the relational neighborhood of a word/term in the vocabulary with the semantic neighborhood of the word/term in the sub-domain. The semantic neighborhood of the word/term in the sub-domain is determined using latent semantic analysis (LSA). We trained and tested the unused sense detection on two clinical text corpora: one contains discharge summaries and the other outpatient visit notes. We were able to detect unused senses with precision from 79% to 87%, recall from 48% to 74%, and an area under receiver operation curve (AUC) of 72% to 87%.

J{sub IC} evaluation of the smooth and the side-grooved CT specimen in the reactor pressure vessel steel (SA508-3)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oh, S.W.; Lim, M.B.; Kim, T.H.

1993-12-31

The elastic-plastic fracture toughness J{sub IC} of SA508-3 forging steel was investigated by using CT-type specimens. The thickness of the smooth specimen is B{sub 0} = 25.4 mm and the side groove specimen is B{sub N} = 20.4 mm and the side groove deep is S{center_dot}G = [(B{sub 0} {minus} B{sub N})/B{sub 0}] {times} 100 = 19.7% and the groove angle is 90{degree}. The J{sub IC} tests estimated according to the method proposed in the ASTM E813-81 and JSME S001-81. The side-grooved specimen have the advantage of J{sub IC} estimation, it is much easier to determine the onset of ductilemore » tearing by the R-curve method and it improved accuracy and scatter of the toughness values thus determined, provided all the size-requirements for the specimen prescribed in the JSME method were satisfied. But it is difficult to find by the ASTM method. The critical stretched zone width (SZW{sub C}) of the side-grooved specimens found to be smaller than that previously determined for the standard CT specimens without side-grooves. This was attributed to higher triaxiality produced by the side-grooves. The stretched zone width method gave slightly larger J{sub IC} values than those by the R-curve method for SA508-3, as has been observed for the standard specimen without side-groove.« less

Noninvasive Determination of Bone Mechanical Properties using Vibration Response: A Refined Model and Validation in vivo

NASA Technical Reports Server (NTRS)

Roberts, S. G.; Hutchinson, T. M.; Arnaud, S. B.; Steele, C. R.; Kiratli, B. J.; Martin, R. B.

1996-01-01

Accurate non-invasive mechanical measurement of long bones is made difficult by the masking effect of surrounding soft tissues. Mechanical Response Tissue Analysis (MRTA) offers a method for separating the effects of the soft tissue and bone; however, a direct validation has been lacking. A theoretical analysis of wave propagation through the compressed tissue revealed a strong mass effect dependent on the relative accelerations of the probe and bone. The previous mathematical model of the bone and overlying tissue system was reconfigured to incorporate the theoretical finding. This newer model (six-parameter) was used to interpret results using MRTA to determine bone cross-sectional bending stiffness, EI(sub MRTA). The relationship between EI(MRTA) and theoretical EI values for padded aluminum rods was R(exp 2) = 0.999. A biological validation followed using monkey tibias. Each bone was tested in vivo with the MRTA instrument. Postmortem, the same tibias were excised and tested to failure in three-point bending to determine EI(sub 3-PT) and maximum load. Diaphyseal Bone Mineral Density (BMD) measurements were also made. The relationship between E(sub 3-PT) and in vivo EI(sub MRTA) using the six-parameter model is strong (R(exp 2) = 0.947) and better than that using the older model (R(exp 2) = 0.645). EI(MRTA) and BMD are also highly correlated (R(exp 2) = 0.853). MRTA measurements in vivo and BMD ex vivo are both good predictors of scaled maximum strength (R(exp 2) = 0.915 and R(exp 2) = 0.894, respectively). This is the first biological validation of a non-invasive mechanical measurement of bone by comparison to actual values. The MRTA technique has potential clinical value for assessing long-bone mechanical properties.

Multi-scale Homogenization of Caddisfly Metacomminities in Human-modified Landscapes

NASA Astrophysics Data System (ADS)

Simião-Ferreira, Juliana; Nogueira, Denis Silva; Santos, Anna Claudia; De Marco, Paulo; Angelini, Ronaldo

2018-04-01

The multiple scale of stream networks spatial organization reflects the hierarchical arrangement of streams habitats with increasingly levels of complexity from sub-catchments until entire hydrographic basins. Through these multiple spatial scales, local stream habitats form nested subsets of increasingly landscape scale and habitat size with varying contributions of both alpha and beta diversity for the regional diversity. Here, we aimed to test the relative importance of multiple nested hierarchical levels of spatial scales while determining alpha and beta diversity of caddisflies in regions with different levels of landscape degradation in a core Cerrado area in Brazil. We used quantitative environmental variables to test the hypothesis that landscape homogenization affects the contribution of alpha and beta diversity of caddisflies to regional diversity. We found that the contribution of alpha and beta diversity for gamma diversity varied according to landscape degradation. Sub-catchments with more intense agriculture had lower diversity at multiple levels, markedly alpha and beta diversities. We have also found that environmental predictors mainly associated with water quality, channel size, and habitat integrity (lower scores indicate stream degradation) were related to community dissimilarity at the catchment scale. For an effective management of the headwater biodiversity of caddisfly, towards the conservation of these catchments, heterogeneous streams with more pristine riparian vegetation found within the river basin need to be preserved in protected areas. Additionally, in the most degraded areas the restoration of riparian vegetation and size increase of protected areas will be needed to accomplish such effort.

Improved silicon nitride for advanced heat engines

NASA Technical Reports Server (NTRS)

Yeh, H. C.; Wimmer, J. M.; Huang, H. H.; Rorabaugh, M. E.; Schienle, J.; Styhr, K. H.

1985-01-01

The AiResearch Casting Company baseline silicon nitride (92 percent GTE SN-502 Si sub 3 N sub 4 plus 6 percent Y sub 2 O sub 3 plus 2 percent Al sub 2 O sub 3) was characterized with methods that included chemical analysis, oxygen content determination, electrophoresis, particle size distribution analysis, surface area determination, and analysis of the degree of agglomeration and maximum particle size of elutriated powder. Test bars were injection molded and processed through sintering at 0.68 MPa (100 psi) of nitrogen. The as-sintered test bars were evaluated by X-ray phase analysis, room and elevated temperature modulus of rupture strength, Weibull modulus, stress rupture, strength after oxidation, fracture origins, microstructure, and density from quantities of samples sufficiently large to generate statistically valid results. A series of small test matrices were conducted to study the effects and interactions of processing parameters which included raw materials, binder systems, binder removal cycles, injection molding temperatures, particle size distribution, sintering additives, and sintering cycle parameters.

A new method to derive electronegativity from resonant inelastic x-ray scattering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carniato, S.; Journel, L.; Guillemin, R.

2012-10-14

Electronegativity is a well-known property of atoms and substituent groups. Because there is no direct way to measure it, establishing a useful scale for electronegativity often entails correlating it to another chemical parameter; a wide variety of methods have been proposed over the past 80 years to do just that. This work reports a new approach that connects electronegativity to a spectroscopic parameter derived from resonant inelastic x-ray scattering. The new method is demonstrated using a series of chlorine-containing compounds, focusing on the Cl 2p{sup -1}LUMO{sup 1} electronic states reached after Cl 1s{yields} LUMO core excitation and subsequent KL radiativemore » decay. Based on an electron-density analysis of the LUMOs, the relative weights of the Cl 2p{sub z} atomic orbital contributing to the Cl 2p{sub 3/2} molecular spin-orbit components are shown to yield a linear electronegativity scale consistent with previous approaches.« less

LoCuSS: THE SUNYAEV-ZEL'DOVICH EFFECT AND WEAK-LENSING MASS SCALING RELATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marrone, Daniel P.; Carlstrom, John E.; Gralla, Megan

2012-08-01

We present the first weak-lensing-based scaling relation between galaxy cluster mass, M{sub WL}, and integrated Compton parameter Y{sub sph}. Observations of 18 galaxy clusters at z {approx_equal} 0.2 were obtained with the Subaru 8.2 m telescope and the Sunyaev-Zel'dovich Array. The M{sub WL}-Y{sub sph} scaling relations, measured at {Delta} = 500, 1000, and 2500 {rho}{sub c}, are consistent in slope and normalization with previous results derived under the assumption of hydrostatic equilibrium (HSE). We find an intrinsic scatter in M{sub WL} at fixed Y{sub sph} of 20%, larger than both previous measurements of M{sub HSE}-Y{sub sph} scatter as well asmore » the scatter in true mass at fixed Y{sub sph} found in simulations. Moreover, the scatter in our lensing-based scaling relations is morphology dependent, with 30%-40% larger M{sub WL} for undisturbed compared to disturbed clusters at the same Y{sub sph} at r{sub 500}. Further examination suggests that the segregation may be explained by the inability of our spherical lens models to faithfully describe the three-dimensional structure of the clusters, in particular, the structure along the line of sight. We find that the ellipticity of the brightest cluster galaxy, a proxy for halo orientation, correlates well with the offset in mass from the mean scaling relation, which supports this picture. This provides empirical evidence that line-of-sight projection effects are an important systematic uncertainty in lensing-based scaling relations.« less

Final Results from the BIMA CMB Anisotropy Survey and Search for Signature of the SZ Effect

NASA Technical Reports Server (NTRS)

Dawson, K. S.; Holzapfel, W. L.; Carlstrom, J. E.; Joy, M.; LaRoque, S. J.

2006-01-01

We report the final results of our study of the cosmic microwave background (CMB) with the BIMA array. Over 1000 hours of observation were dedicated to this project exploring CMB anisotropy on scales between 1' and 2' in eighteen 6'.6 FWHM fields. In the analysis of the CMB power spectrum, the visibility data is divided into two bins corresponding to different angular scales. Modeling the observed excess power as a flat band of average multipole l(sub eff)= 5237, we find deltaT(sup 2)(sub 1) = 220(sup +140)(sub -120) mu K(sup 2) at 68% confidence and deltaT(sup 2)(sub 1) greater than 0 muK(sup 2) with 94.7% confidence. In a second band with average multipole of l(sub eff) = 8748, we find deltaT(sup 2)(sub 2) consistent with zero, and an upper limit 880 muK(sup 2) at 95% confidence. An extensive series of tests and supplemental observations with the VLA provide strong evidence against systematic errors or radio point sources being the source of the observed excess power. The dominant source of anisotropy on these scales is expected to arise from the Sunyaev-Zel'dovich (SZ) effect in a population of distant galaxy clusters. If the excess power is due to the SZ effect, we can place constraints on the normalization of the matter power spectrum sigma(sub 8) = 1.03(sup +0.20)(sub -0.29) at 68% confidence. The distribution of pixel fluxes in the BIMA images are found to be consistent with simulated observations of the expected SZ background and rule out instrumental noise or radio sources as the source of the observed excess power with similar confidence to the detection of excess power. Follow-up optical observations to search for galaxy over-densities anti-correlated with flux in the BIMA images, as might be expected from the SZ effect, proved to be inconclusive.

EFFECTS OF COFIRING LIGNIN AND BIOSOLIDS WITH COAL ON FIRESIDE PERFORMANCE AND COMBUSTION PRODUCTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kevin C. Galbreath

2002-08-01

Lignin, derived from municipal solid waste and biosolid feedstocks using Masada Resource Group's patented CES OxyNol{trademark} process, and acidified biosolids were evaluated as supplemental fuels with coal for producing steam and electricity. Tests were conducted in a pilot-scale (550,000-Btu/hr [580-MJ/hr]) combustion system to evaluate the effects of coal characteristics, blend mixture (on a dry wt% basis) and furnace exit gas temperature (FEGT) on boiler heat-exchange surface slagging and fouling, NO{sub x} and SO{sub x} production, fly ash characteristics, and combustion efficiency. The effects of blending lignin and acidified biosolids with coal on fuel handling and pulverization characteristics were also addressed.more » An 80 wt% Colorado--20 wt% subbituminous Powder River Basin coal blend from the Tennessee Valley Authority Colbert Steam Plant, hereafter referred to as the Colbert coal, and a bituminous Pittsburgh No. 8 coal were tested. The lignin and acidified biosolids were characterized by possessing higher moisture content and lower carbon, hydrogen, and heating values relative to the coals. Ash contents of the fuels were similar. The lignin also possessed higher concentrations of TiO{sub 2}, CaO, and SO{sub 3} and lower concentrations of SiO{sub 2}, Al{sub 2}O{sub 3}, Fe{sub 2}O{sub 3}, K{sub 2}O, and N relative to the coals. The sulfur content of lignin could be reduced through a more thorough washing and drying of the lignin in an efficient commercial-scale dewatering device. Acidified biosolids were distinguished by higher concentrations of P{sub 2}O{sub 5} and MgO and lower SiO{sub 2} and Al{sub 2}O{sub 3} relative to the other fuels. Trace element concentrations, especially for Cr, Pb, Hg, and Ni, were generally greater in the lignin and acidified biosolid fuels relative to the Colbert coal. Maximum trace element emission factors were calculated for 95:5 Colbert coal--lignin and 90:5:5 Colbert coal--lignin--acidified biosolid blends and compared to U.S. Environmental Protection Agency emission factors for pulverized coal-fired units that are unequipped with pollution control devices. Calculated maximum trace element emission factors for the fuel blends were generally less than or within the range of those for the uncontrolled coal-fired units, except for Cr and Pb which were greater.« less

Spectral contaminant identifier for off-axis integrated cavity output spectroscopy measurements of liquid water isotopes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brian Leen, J.; Berman, Elena S. F.; Gupta, Manish

Developments in cavity-enhanced absorption spectrometry have made it possible to measure water isotopes using faster, more cost-effective field-deployable instrumentation. Several groups have attempted to extend this technology to measure water extracted from plants and found that other extracted organics absorb light at frequencies similar to that absorbed by the water isotopomers, leading to {delta}{sup 2}H and {delta}{sup 18}O measurement errors ({Delta}{delta}{sup 2}H and {Delta}{delta}{sup 18}O). In this note, the off-axis integrated cavity output spectroscopy (ICOS) spectra of stable isotopes in liquid water is analyzed to determine the presence of interfering absorbers that lead to erroneous isotope measurements. The baseline offsetmore » of the spectra is used to calculate a broadband spectral metric, m{sub BB}, and the mean subtracted fit residuals in two regions of interest are used to determine a narrowband metric, m{sub NB}. These metrics are used to correct for {Delta}{delta}{sup 2}H and {Delta}{delta}{sup 18}O. The method was tested on 14 instruments and {Delta}{delta}{sup 18}O was found to scale linearly with contaminant concentration for both narrowband (e.g., methanol) and broadband (e.g., ethanol) absorbers, while {Delta}{delta}{sup 2}H scaled linearly with narrowband and as a polynomial with broadband absorbers. Additionally, the isotope errors scaled logarithmically with m{sub NB}. Using the isotope error versus m{sub NB} and m{sub BB} curves, {Delta}{delta}{sup 2}H and {Delta}{delta}{sup 18}O resulting from methanol contamination were corrected to a maximum mean absolute error of 0.93 per mille and 0.25 per mille respectively, while {Delta}{delta}{sup 2}H and {Delta}{delta}{sup 18}O from ethanol contamination were corrected to a maximum mean absolute error of 1.22 per mille and 0.22 per mille . Large variation between instruments indicates that the sensitivities must be calibrated for each individual isotope analyzer. These results suggest that the properly calibrated interference metrics can be used to correct for polluted samples and extend off-axis ICOS measurements of liquid water to include plant waters, soil extracts, wastewater, and alcoholic beverages. The general technique may also be extended to other laser-based analyzers including methane and carbon dioxide isotope sensors.« less

An investigation into the psychometric properties of the Hospital Anxiety and Depression Scale in patients with breast cancer

PubMed Central

Rodgers, Jacqui; Martin, Colin R; Morse, Rachel C; Kendell, Kate; Verrill, Mark

2005-01-01

Background To determine the psychometric properties of the Hospital Anxiety and Depression Scale (HADS) in patients with breast cancer and determine the suitability of the instrument for use with this clinical group. Methods A cross-sectional design was used. The study used a pooled data set from three breast cancer clinical groups. The dependent variables were HADS anxiety and depression sub-scale scores. Exploratory and confirmatory factor analyses were conducted on the HADS to determine its psychometric properties in 110 patients with breast cancer. Seven models were tested to determine model fit to the data. Results Both factor analysis methods indicated that three-factor models provided a better fit to the data compared to two-factor (anxiety and depression) models for breast cancer patients. Clark and Watson's three factor tripartite and three factor hierarchical models provided the best fit. Conclusion The underlying factor structure of the HADS in breast cancer patients comprises three distinct, but correlated factors, negative affectivity, autonomic anxiety and anhedonic depression. The clinical utility of the HADS in screening for anxiety and depression in breast cancer patients may be enhanced by using a modified scoring procedure based on a three-factor model of psychological distress. This proposed alternate scoring method involving regressing autonomic anxiety and anhedonic depression factors onto the third factor (negative affectivity) requires further investigation in order to establish its efficacy. PMID:16018801

Radio measurements of the energy and the depth of the shower maximum of cosmic-ray air showers by Tunka-Rex

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bezyazeekov, P.A.; Budnev, N.M.; Gress, O.A.

2016-01-01

We reconstructed the energy and the position of the shower maximum of air showers with energies E ∼> 100 PeV applying a method using radio measurements performed with Tunka-Rex. An event-to-event comparison to air-Cherenkov measurements of the same air showers with the Tunka-133 photomultiplier array confirms that the radio reconstruction works reliably. The Tunka-Rex reconstruction methods and absolute scales have been tuned on CoREAS simulations and yield energy and X{sub max} values consistent with the Tunka-133 measurements. The results of two independent measurement seasons agree within statistical uncertainties, which gives additional confidence in the radio reconstruction. The energy precision of Tunka-Rex is comparablemore » to the Tunka-133 precision of 15%, and exhibits a 20% uncertainty on the absolute scale dominated by the amplitude calibration of the antennas. For X{sub max}, this is the first direct experimental correlation of radio measurements with a different, established method. At the moment, the X{sub max} resolution of Tunka-Rex is approximately 40 g/cm{sup 2}. This resolution can probably be improved by deploying additional antennas and by further development of the reconstruction methods, since the present analysis does not yet reveal any principle limitations.« less

On the Subgrid-Scale Modeling of Compressible Turbulence

NASA Technical Reports Server (NTRS)

Squires, Kyle; Zeman, Otto

1990-01-01

A new sub-grid scale model is presented for the large-eddy simulation of compressible turbulence. In the proposed model, compressibility contributions have been incorporated in the sub-grid scale eddy viscosity which, in the incompressible limit, reduce to a form originally proposed by Smagorinsky (1963). The model has been tested against a simple extension of the traditional Smagorinsky eddy viscosity model using simulations of decaying, compressible homogeneous turbulence. Simulation results show that the proposed model provides greater dissipation of the compressive modes of the resolved-scale velocity field than does the Smagorinsky eddy viscosity model. For an initial r.m.s. turbulence Mach number of 1.0, simulations performed using the Smagorinsky model become physically unrealizable (i.e., negative energies) because of the inability of the model to sufficiently dissipate fluctuations due to resolved scale velocity dilations. The proposed model is able to provide the necessary dissipation of this energy and maintain the realizability of the flow. Following Zeman (1990), turbulent shocklets are considered to dissipate energy independent of the Kolmogorov energy cascade. A possible parameterization of dissipation by turbulent shocklets for Large-Eddy Simulation is also presented.

Behavioural problems in children with enuresis

PubMed Central

Birdal, Seval; Doğangün, Burak

2016-01-01

Aim: Enuresis is defined as involuntary or intentional repeated voiding of urine into clothes or bed at least twice a week for a period of three consecutive months in children older than five years old. It is one of the most frequent chronic childhood disorders. The aim of this study was to investigate the frequency of behavioural problems in children with enuresis. Material and Methods: The research compared 30 children aged between 7 and 11 years who had consulted to Bakırköy Prof. Dr. Mazhar Osman Mental Health and Neurological Diseases Training and Research Hospital, Child and Adolescent Psychiatry Clinics and diagnosed with enuresis with their 30 peers who were randomly selected from a state elementary school. The Child Behaviour Checklist was applied to both groups. Results: The subdimension scores of both groups were compared, it was observed that children with enuresis had higher scores compared to their peers in all sub-tests except for the Sluggish Cognitive Tempo, Anxiety Disorders, and Obsessive Compulsive Disorder sub-tests. Enuretic children had higher scores in externalizing (p<0.001), internalizing (p=0.001) and total problem (p<0.001) scales. Conclusion: The results of this study indicate that children with enuresis exhibit behavioral problems with a higher rate compared to their healthy peers. The results are in line with the literature. Moreover, compered to the results of the studies conducted in different countries, significantly higher scores in internalizing problems were obtained. It was thought is possible that this might be related with cultural factors. However, these findings need to be verified with data from larger scale studies. PMID:27738398

Program Manager Assessments: Professionalism Personified

DTIC Science & Technology

2015-08-01

dozens of legacy systems. A few years ago, the idea of modernizing this collection in a “ big bang ” approach was rejected in favor of a lower-risk and...chain of com- mand. The assessments are simul - taneously sent to me, the Service or Component acquisition executive, and the program executive officer...use of actual test results at sub-scale, com- ponent testing, modeling, simulation , and field testing were all described in fair detail. Key near

IRAS Colors of the Pleiades

NASA Technical Reports Server (NTRS)

Carey, Sean J.; Shipman, R. F.; Clark, F. O.

1996-01-01

We present large scale images of the infrared emission of the region around the Pleiades using the ISSA data product from the IRAS mission. Residual Zodiacal background and a discontinuity in the image due to the scanning strategy of the satellite necessitated special background subtraction methods. The 60/100 color image clearly shows the heating of the ambient interstellar medium by the cluster. The 12/100 and 25/100 images peak on the cluster as expected for exposure of small dust grains to an enhanced UV radiation field; however, the 25/100 color declines to below the average interstellar value at the periphery of the cluster. Potential causes of the color deficit are discussed. A new method of identifying dense molecular material through infrared emission properties is presented. The difference between the 100 micron flux density and the 60 micron flux density scaled by the average interstellar 60/100 color ratio (Delta I(sub 100) is a sensitive diagnostic of material with embedded heating sources (Delta I(sub 100) less than 0) and cold, dense cores (Delta I(sub 100) greater than 0). The dense cores of the Taurus cloud complex as well as Lynds 1457 are clearly identified by this method, while the IR bright but diffuse Pleiades molecular cloud is virtually indistinguishable from the nearby infrared cirrus.

Recent developments in the growth, processing, and testing of rare earth doped YVO{sub 4} single crystals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mizell, G.; Fay, W.R.; Alekel, T. III

1994-12-31

The production of the laser host material YVO{sub 4} via high temperature solution growth (HTSG) is described as a facile alternative for producing optical quality crystals for research. The effects of dopant concentration on optical absorption properties in 0.7% and 3% Nd:YVO{sub 4} crystals are discussed. The rare earths ions Ho{sup 3+} and Er{sup 3+} have been doped into YVO{sub 4} with the HTSG method, and inaugural optical properties of Ho{sub 0.04}Y{sub 0.96}VO{sub 4} are presented.

A soil bioassay using the nematode Caenorhabditis elegans

DOE Office of Scientific and Technical Information (OSTI.GOV)

Freeman, M.N.; Peredney, C.L.; Williams, P.L.

1999-07-01

Caenorhabditis elegans is a free-livings soil nematode that is commonly used as a biological model. Recently, much work has been done using the nematode as a toxicological model as well. Much of the work involving C. elegans has been performed in aquatic media, since it lives in the interstitial water of soil. However, testing in soil would be expected to more accurately reproduce the organism's normal environment and may take into consideration other factors not available in an aquatic test, i.e., toxicant availability effects due to sorption, various chemical interactions, etc. This study used a modification of a previous experimentalmore » protocol to determine 24h LC{sub 50} values for Cu in a Cecil series soil mixture, and examined the use of CuCl{sub 2} as a reference toxicant for soil toxicity testing with C. elegans. Three different methods of determining percent lethality were used, each dependent on how the number of worms missing after the recovery process was used in the lethality calculations. Only tests having {ge}80% worm recovery and {ge}90% control survival were used in determining the LC{sub 50}s, by Probit analysis. The replicate LC{sub 50} values generated a control chart for each method of calculating percent lethality. The coefficient of variation (CV) for each of the three methods was {le}14%. The control charts and the protocol outlined in this study are intended to be used to assess test organism health and monitor precision of future soil toxicity tests with C. elegans.« less

PM-1 NUCLEAR POWER PLANT PROGRAM. Quarterly Progress Report No. 2 for June 1 to August 31, 1959

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sieg, J.S.; Smith, E.H.

1959-10-01

The objective of the contract is the design, development, fabrication, installation, and initial testing and operation of a prepackaged air- transportable pressurized water reactor nuclear power plant, the PM-1. The specified output is 1 Mwe and 7 million Btu/hr of heat. The plant is to be operational by March 1962. The principal efforts were completion of the plant parametric study and preparation of the preliminary design. A summary of design parameters is given. Systems development work included study and selection of packages for full-scale testing, a survey of in-core instrumentation techniques, control and instrumentation development, and development of components formore » the steam generator, condenser, and turbine generator, which are not commercially available. Reactor development work included completion of the parametric zeropower experiments and preparrtions for a flexible zeropower test program, a revision of plans for irradiation testing PM-1 fuel elements, initiation of a reactor flow test program, outliring of a heat tnansfer test program, completion of the seven-tube test section (SETCH-1) tests, and evaluation of control rod actuators leading to specification of a magnetic jack-type control rod drive similar to that reported in ANL-5768. Completion of the prelimirary design led to initiation of the final design effort, which will be the principal activity during the next two project quarters. Preparations for core fabrication included procurement of core cladding material for the zero-power teat core, arrangement with a subcontractor to convent UF/sub 6/ to UO/sub 2/ and to commence delivery of the oxide during the next quarter, development of fuel element fabrication and ultrasonic testing techniques, study of control rod materials, UO/sub 2/ recovery techniques, and boron analysis methods. Preliminary work on site preparation was pursued with receipt of USAEC approval for a location on the eastern slope of Warren Peak at Sundance, Wyoming. A survey of this site is underway. A preliminary Hazards Summary Report is in preparation. (For preceding period see MND-M-1812.) (auth)« less

Discrimination of coherent features in turbulent boundary layers by the entropy method

NASA Technical Reports Server (NTRS)

Corke, T. C.; Guezennec, Y. G.

1984-01-01

Entropy in information theory is defined as the expected or mean value of the measure of the amount of self-information contained in the ith point of a distribution series x sub i, based on its probability of occurrence p(x sub i). If p(x sub i) is the probability of the ith state of the system in probability space, then the entropy, E(X) = - sigma p(x sub i) logp (x sub i), is a measure of the disorder in the system. Based on this concept, a method was devised which sought to minimize the entropy in a time series in order to construct the signature of the most coherent motions. The constrained minimization was performed using a Lagrange multiplier approach which resulted in the solution of a simultaneous set of non-linear coupled equations to obtain the coherent time series. The application of the method to space-time data taken by a rake of sensors in the near-wall region of a turbulent boundary layer was presented. The results yielded coherent velocity motions made up of locally decelerated or accelerated fluid having a streamwise scale of approximately 100 nu/u(tau), which is in qualitative agreement with the results from other less objective discrimination methods.

An Assessment of Ares I-X Aeroacoustic Measurements with Comparisons to Pre-Flight Wind Tunnel Test Results

NASA Technical Reports Server (NTRS)

Nance, Donald K.; Reed, Darren K.

2011-01-01

During the recent successful launch of the Ares I-X Flight Test Vehicle, aeroacoustic data was gathered at fifty-seven locations along the vehicle as part of the Developmental Flight Instrumentation. Several of the Ares I-X aeroacoustic measurements were placed to duplicate measurement locations prescribed in pre-flight, sub-scale wind tunnel tests. For these duplicated measurement locations, comparisons have been made between aeroacoustic data gathered during the ascent phase of the Ares I-X flight test and wind tunnel test data. These comparisons have been made at closely matching flight conditions (Mach number and vehicle attitude) in order to preserve a one-to-one relationship between the flight and wind tunnel data. These comparisons and the current wind tunnel to flight scaling methodology are presented and discussed. The implications of using wind tunnel test data scaled under the current methodology to predict conceptual launch vehicle aeroacoustic environments are also discussed.

Sorption enhanced reaction process (SERP) for the production of hydrogen

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hufton, J.; Mayorga, S.; Gaffney, T.

1998-08-01

The novel Sorption Enhanced Reaction Process has the potential to decrease the cost of hydrogen production by steam methane reforming. Current effort for development of this technology has focused on adsorbent development, experimental process concept testing, and process development and design. A preferred CO{sub 2} adsorbent, K{sub 2}CO{sub 3} promoted hydrotalcite, satisfies all of the performance targets and it has been scaled up for process testing. A separate class of adsorbents has been identified which could potentially improve the performance of the H{sub 2}-SER process. Although this material exhibits improved CO{sub 2} adsorption capacity compared to the HTC adsorbent, itsmore » hydrothermal stability must be improved. Single-step process experiments (not cyclic) indicate that the H{sub 2}-SER reactor performance during the reaction step improves with decreasing pressure and increasing temperature and steam to methane ratio in the feed. Methane conversion in the H{sub 2}-SER reactor is higher than for a conventional catalyst-only reactor operated at similar temperature and pressure. The reactor effluent gas consists of 90+% H{sub 2}, balance CH{sub 4}, with only trace levels (< 50 ppm) of carbon oxides. A best-case process design (2.5 MMSCFD of 99.9+% H{sub 2}) based on the HTC adsorbent properties and a revised SER process cycle has been generated. Economic analysis of this design indicates the process has the potential to reduce the H{sub 2} product cost by 25--31% compared to conventional steam methane reforming.« less

Development and test of different methods to improve the description and NO{sub x} emissions in staged combustion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brink, A.; Kilpinen, P.; Hupa, M.

1996-01-01

Two methods to improve the modeling of NO{sub x} emissions in numerical flow simulation of combustion are investigated. The models used are a reduced mechanism for nitrogen chemistry in methane combustion and a new model based on regression analysis of perfectly stirred reactor simulations using detailed comprehensive reaction kinetics. The applicability of the methods to numerical flow simulation of practical furnaces, especially in the near burner region, is tested against experimental data from a pulverized coal fired single burner furnace. The results are also compared to those obtained using a commonly used description for the overall reaction rate of NO.

Determination of vitamin B/sub 6/ bioavailability in animal tissues using intrinsic and extrinsic labeling in the rat

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ink, S.L.; Gregory, J.F. III; Sartain, D.B.

The effect of thermal processing on the bioavailability of vitamin B/sub 6/ in liver and muscle was examined by radioisotopic enrichment of these tissues. Rats were fed a single gelled test meal containing rat liver or muscle intrinsically enriched by vascular perfusion with (/sup 3/H)vitamin B/sub 6/ or a gelled test meal containing (/sup 3/H)pyridoxine (PN). Diets were extrinsically enriched with (/sup 14/C)PN to permit a direct comparison of enrichment methods. Absorption and metabolism were examined by analysis of tissues and excreta 24 h after the test meal had been consumed. The bioavailability of (/sup 3/H)B/sub 6/ vitamers in themore » raw tissues was equivalent to that of (/sup 3/H)PN in controls. Thermal processing of the tissues (121/sup 0/C, 45 min) induced destruction of 25-30% of the (/sup 3/H)B/sub 6/ vitamers and weakly reduced (less than or equal to10%) the utilization of the remaining(/sup 3/H)B/sub 6/ vitamers. The presence of monosodium glutamate (MSG) during thermal processing did not alter the results. The utilization of (/sup 14/C)PN was unaffected by diet composition. These data demonstrate the high bioavailability of vitamin B/sub 6/ in animal-derived foods and support the use of isotopic enrichment methods as an alternative to conventional bioassay procedures.« less