Investigation of Hypervelocity Impact Phenomena Using Real-Time Concurrent Diagnostics

NASA Astrophysics Data System (ADS)

Mihaly, Jonathan Michael

Hypervelocity impact of meteoroids and orbital debris poses a serious and growing threat to spacecraft. To study hypervelocity impact phenomena, a comprehensive ensemble of real-time concurrently operated diagnostics has been developed and implemented in the Small Particle Hypervelocity Impact Range (SPHIR) facility. This suite of simultaneously operated instrumentation provides multiple complementary measurements that facilitate the characterization of many impact phenomena in a single experiment. The investigation of hypervelocity impact phenomena described in this work focuses on normal impacts of 1.8 mm nylon 6/6 cylinder projectiles and variable thickness aluminum targets. The SPHIR facility two-stage light-gas gun is capable of routinely launching 5.5 mg nylon impactors to speeds of 5 to 7 km/s. Refinement of legacy SPHIR operation procedures and the investigation of first-stage pressure have improved the velocity performance of the facility, resulting in an increase in average impact velocity of at least 0.57 km/s. Results for the perforation area indicate the considered range of target thicknesses represent multiple regimes describing the non-monotonic scaling of target perforation with decreasing target thickness. The laser side-lighting (LSL) system has been developed to provide ultra-high-speed shadowgraph images of the impact event. This novel optical technique is demonstrated to characterize the propagation velocity and two-dimensional optical density of impact-generated debris clouds. Additionally, a debris capture system is located behind the target during every experiment to provide complementary information regarding the trajectory distribution and penetration depth of individual debris particles. The utilization of a coherent, collimated illumination source in the LSL system facilitates the simultaneous measurement of impact phenomena with near-IR and UV-vis spectrograph systems. Comparison of LSL images to concurrent IR results indicates two distinctly different phenomena. A high-speed, pressure-dependent IR-emitting cloud is observed in experiments to expand at velocities much higher than the debris and ejecta phenomena observed using the LSL system. In double-plate target configurations, this phenomena is observed to interact with the rear-wall several micro-seconds before the subsequent arrival of the debris cloud. Additionally, dimensional analysis presented by Whitham for blast waves is shown to describe the pressure-dependent radial expansion of the observed IR-emitting phenomena. Although this work focuses on a single hypervelocity impact configuration, the diagnostic capabilities and techniques described can be used with a wide variety of impactors, materials, and geometries to investigate any number of engineering and scientific problems.

The 5-6 December 1991 FIRE IFO 2 Jet Stream Cirrus Case Study: Possible Influences of Volcanic Aerosols

NASA Technical Reports Server (NTRS)

Sassen, Kenneth; Starr, David OC.; Mace, Gerald G.; Poellot, Michael R.; Melfi, S. H.; Eberhard, Wynn L.; Spinhirne, James D.; Eloranta, E. W.; Hagen, Donald E.; Hallett, John

1996-01-01

In presenting an overview of the cirrus clouds comprehensively studied by ground based and airborne sensors from Coffeyville, Kansas, during the 5-6 December 1992 First ISCCP Regional Experiment (FIRE) intensive field observation (IFO) case study period, evidence is provided that volcanic aerosols from the June 1991 Pinatubo eruptions may have significantly influenced the formation and maintenance of the cirrus. Following the local appearance of a spur of stratospheric volcanic debris from the subtropics, a series of jet streaks subsequently conditioned the troposphere through tropopause foldings with sulfur based particles that became effective cloud forming nuclei in cirrus clouds. Aerosol and ozone measurements suggest a complicated history of stratospheric-tropospheric exchanges embedded with the upper level flow, and cirrus cloud formation was noted to occur locally at the boundaries of stratospheric aerosol enriched layers that became humidified through diffusion, precipitation, or advective processes. Apparent cirrus cloud alterations include abnormally high ice crystal concentrations (up to approximately 600 L(exp. 1)), complex radial ice crystal types, and relatively large haze particles in cirrus uncinus cell heads at temperatures between -40 and -50 degrees C. Implications for volcanic-cirrus cloud climate effects and unusual (nonvolcanic) aerosol jet stream cirrus cloud formation are discussed.

a Numerical Study of Close Approaches for a Cloud of Debris Considering Atmospheric Drag and Lift

NASA Astrophysics Data System (ADS)

Gomes, Vivian; Golebiewska, Justyna; Prado, Antonio

The present paper study close approaches between a group of debris and a planet. The dynamical model considers the atmosphere of the planet, both in terms of drag as well as lift. This cloud is created during the passage of the spacecraft by the atmosphere of the planet, which is the responsible by the explosion of the spacecraft. The dynamical system is compos by the planet, the Sun, and the spacecraft, which explodes and becomes a cloud of debris. The planet and the Sun are in circular planar orbits. The equations of motion are the ones of the circular planar restricted three-body problem with the addition of the forces given by the atmospheric: drag and lift. The planet Jupiter is used for the numerical simulations. The initial conditions of the spacecraft and the debris are specified at the periapsis, which is the point where the explosion occurs. The equations of motion are numerically integrated forward in time for each particle, until a point where the particle is at a distance that can be considered far enough from the planet and it is possible to disregard the effects of the planet and consider the Sun-particle as a two-body system. Then we compute the velocity, energy and angular momentum after the passage by the planet, for each particle, based in the two-body celestial mechanics. From those results, the eccentricity and the semi-major axis of each particle can be obtained. Then, the orbit of the spacecraft is integrated backwards in time, as a single body. The difference from the usual close approaches technique is the presence of the atmosphere of the planet, which generates a drag and a lift forces in the spacecraft, which causes the explosion and modifies the trajectories of the debris generated by the explosion. The primary objective of the present paper is to map the modifications of the orbits of the debris that compose the cloud due to the close approach with the planet. Emphasis is given to map the orbital parameters of the debris after the close approach with the planet. Then, the effects are compared with the same maneuvers performed without the inclusion of the atmosphere. This type of research is useful, because it helps to obtain the size and density of the cloud of debris after the passage, as a function of time. That information has impact on the evaluations of the risks that spacecrafts suffer when passing by shorter distances from this cloud.

On the Magnitude of the Electric Field Near Thunderstorm-Associated Clouds

NASA Technical Reports Server (NTRS)

Merceret, Francis J.; Ward, Jennifer G.; Mach, Douglas M.; Bateman, Monte G.; Dye, James E.

2007-01-01

Electric field measurements made in and near clouds during two airborne field mill programs are presented. Aircraft equipped with multiple electric field mills and cloud physics sensors were flown near active convection and into thunderstorm anvil and debris clouds. The magnitude of the electric field was measured as a function of position with respect to the cloud edge in order to provide an observational basis for modifications to the lightning launch commit criteria (LLCC) used by the U.S. space program. These LLCC are used to reduce the risk that an ascending launch vehicle will trigger a lightning strike that could cause the loss of the mission or vehicle. The results suggest that even with fields of tens of kV/m inside electrically active convective clouds, the fields external to these clouds decay to less than 3 kV/m within fifteen kilometers of cloud edge. Fields exceeding 3 kV/m were not found external to anvil and debris clouds.

Element fracture technique for hypervelocity impact simulation

NASA Astrophysics Data System (ADS)

Zhang, Xiao-tian; Li, Xiao-gang; Liu, Tao; Jia, Guang-hui

2015-05-01

Hypervelocity impact dynamics is the theoretical support of spacecraft shielding against space debris. The numerical simulation has become an important approach for obtaining the ballistic limits of the spacecraft shields. Currently, the most widely used algorithm for hypervelocity impact is the smoothed particle hydrodynamics (SPH). Although the finite element method (FEM) is widely used in fracture mechanics and low-velocity impacts, the standard FEM can hardly simulate the debris cloud generated by hypervelocity impact. This paper presents a successful application of the node-separation technique for hypervelocity impact debris cloud simulation. The node-separation technique assigns individual/coincident nodes for the adjacent elements, and it applies constraints to the coincident node sets in the modeling step. In the explicit iteration, the cracks are generated by releasing the constrained node sets that meet the fracture criterion. Additionally, the distorted elements are identified from two aspects - self-piercing and phase change - and are deleted so that the constitutive computation can continue. FEM with the node-separation technique is used for thin-wall hypervelocity impact simulations. The internal structures of the debris cloud in the simulation output are compared with that in the test X-ray graphs under different material fracture criteria. It shows that the pressure criterion is more appropriate for hypervelocity impact. The internal structures of the debris cloud are also simulated and compared under different thickness-to-diameter ratios (t/D). The simulation outputs show the same spall pattern with the tests. Finally, the triple-plate impact case is simulated with node-separation FEM.

Ejecta cloud from the AIDA space project kinetic impact on the secondary of a binary asteroid: I. mechanical environment and dynamical model

NASA Astrophysics Data System (ADS)

Yu, Yang; Michel, Patrick; Schwartz, Stephen R.; Naidu, Shantanu P.; Benner, Lance A. M.

2017-01-01

An understanding of the post-impact dynamics of ejecta clouds are crucial to the planning of a kinetic impact mission to an asteroid, and also has great implications for the history of planetary formation. The purpose of this article is to track the evolution of ejecta produced by AIDA mission, which targets for kinetic impact the secondary of near-Earth binary asteroid (65803) Didymos on 2022, and to feedback essential informations to AIDA's ongoing phase-A study. We present a detailed dynamic model for the simulation of an ejecta cloud from a binary asteroid that synthesizes all relevant forces based on a previous analysis of the mechanical environment. We apply our method to gain insight into the expected response of Didymos to the AIDA impact, including the subsequent evolution of debris and dust. The crater scaling relations from laboratory experiments are employed to approximate the distributions of ejecta mass and launching speed. The size distribution of fragments is modeled with a power law fitted from observations of real asteroid surface. A full-scale demonstration is simulated using parameters specified by the mission. We report the results of the simulation, which include the computed spread of the ejecta cloud and the recorded history of ejecta accretion and escape. The violent period of the ejecta evolution is found to be short, and is followed by a stage where the remaining ejecta is gradually cleared. Solar radiation pressure proves to be efficient in cleaning dust-size ejecta, and the simulation results after two weeks shows that large debris on polar orbits (perpendicular to the binary orbital plane) has a survival advantage over smaller ejecta and ejecta that keeps to low latitudes.

Hypervelocity impact of mm-size plastic projectile on thin aluminum plate

NASA Astrophysics Data System (ADS)

Poniaev, S. A.; Kurakin, R. O.; Sedov, A. I.; Bobashev, S. V.; Zhukov, B. G.; Nechunaev, A. F.

2017-06-01

The experimental studies of the process of hypervelocity (up to 6 km/s) impact of a mm-size projectile on a thin aluminum plate is described. The numerical simulation of this process is presented. The data on the evolution, structure, and composition of the debris cloud formed as a result of the impact are reported. Basic specific features of the debris cloud formation are revealed.

Interstellar Explorer Observations of the Solar System's Debris Disks

NASA Astrophysics Data System (ADS)

Lisse, C. M.; McNutt, R. L., Jr.; Brandt, P. C.

2017-12-01

Planetesimal belts and debris disks full of dust are known as the "signposts of planet formation" in exosystems. The overall brightness of a disk provides information on the amount of sourcing planetesimal material, while asymmetries in the shape of the disk can be used to search for perturbing planets. The solar system is known to house two such belts, the Asteroid belt and the Kuiper Belt; and at least one debris cloud, the Zodiacal Cloud, sourced by planetisimal collisions and Kuiper Belt comet evaporative sublimation. However these are poorly understood in toto because we live inside of them. E.g., while we know of the two planetesimal belt systems, it is not clear how much, if any, dust is produced from the Kuiper belt since the near-Sun comet contributions dominate near-Earth space. Understanding how much dust is produced in the Kuiper belt would give us a much better idea of the total number of bodies in the belt, especially the smallest ones, and their dynamical collisional state. Even for the close in Zodiacal cloud, questions remain concerning its overall shape and orientation with respect to the ecliptic and invariable planes of the solar system - they aren't explainable from the perturbations caused by the known planets alone. In this paper we explore the possibilities of using an Interstellar Explorer telescope placed at 200 AU from the sun to observe the brightness, shape, and extent of the solar system's debris disk(s). We should be able to measure the entire extent of the inner, near-earth zodiacal cloud; whether it connects smoothly into an outer cloud, or if there is a second outer cloud sourced by the Kuiper belt and isolated by the outer planets, as predicted by Stark & Kuchner (2009, 2010) and Poppe et al. (2012, 2016; Figure 1). VISNIR imagery will inform about the dust cloud's density, while MIR cameras will provide thermal imaging photometry related to the cloud's dust particle size and composition. Observing at high phase angle by looking back towards the sun from 200 AU, we will be able to perform deep searches for the presence of rings and dust clouds around discrete sources, and thus we will be able to search for possible strong individual sources of the debris clouds - like the Haumea family collisional fragments, or the rings of the Centaur Chariklo, or dust emitted from spallation off the 6 known bodies of the Pluto system.

Orbital Debris: Quarterly News, Volume 14, Issue 2

NASA Technical Reports Server (NTRS)

Liou, J. C. (Editor); Shoots, Debi (Editor)

2010-01-01

This bulletin contains articles from the Orbital Debris Program office. This issue's articles are: "Orbital Debris Success Story --A Decade in the Making", "Old and New Satellite Breakups Identified," "Update on Three Major Debris Clouds," and "MMOD Inspection of the HST Bay 5 Multi-Layer Insulation Panel" about micrometeoroid and orbital debris (MMOD) inspection of the Hubble Space Telescope (HST) insulation panel. A project review is also included (i.e., "Small Debris Observations from the Iridium 33/Cosmos 2251 Collision.") There are also abstra cts of conference papers from the staff of the program office.

On the existence of debris clouds in the Space Station orbit: Final results of the EuroMir 1995 impact detector

NASA Technical Reports Server (NTRS)

Maag, Carl R.; Deshpande, Sunil P.; Johnson, Nicholas L.

1997-01-01

A flight experiment flown onboard the Mir space station as a part of the Euromir 95 mission is considered. The aim of the experiment was to develop a greater understanding of the effects of the space environment on materials. In addition to the active enumeration of particle impacts and trajectories, the aim was to capture hypervelocity particles for their return to earth. Postflight measurements were performed to determine the flux density, diameters and subsequent effects on various optical thermal control and structural materials. Sensors actively measured the atomic oxygen flux, the contamination depostion and their effects during the mission. Two clouds of small particles were detected during a period of 100 days onboard Mir. It is concluded that the measured momenta of these particles suggests that their size and velocity are such that they cause damage to optics and thermal control surfaces.

The surgical management of benign and malignant thyroid neoplasms in Marshall Islanders exposed to hydrogen bomb fallout.

PubMed

Dobyns, B M; Hyrmer, B A

1992-01-01

On March 1, 1954, a serious fallout accident occurred during the United States atomic testing program at Bikini in the Trust Territory of the Pacific Islands. Following the detonation of a large thermonuclear device (known as Bravo) an unexpected shift in winds resulted in deposition of radioactive debris on several inhabited atolls in the Marshall Islands. During the early post-detonation period military, sea, and air surveys traced the hottest portion of the parabolic cloud as it drifted in an ever widening pattern of diminishing concentration eastward and southeast of Bikini. The center of the cloud passed North of the Rongelap Atoll, which was the nearest inhabited atoll. This report concerns the development of thyroid lesions, the special circumstances encountered during thyroid surgery, and the results of the surgical management of benign and malignant lesions that were subsequently encountered in this population.

Orbital Debris Quarterly News, Vol. 13, No. 2

NASA Technical Reports Server (NTRS)

Liou, J.-C. (Editor); Shoots, Debi (Editor)

2009-01-01

Topics include: debris clouds left by satellite collision; debris flyby near the International Space Station; and break-up of an ullage motor from a Russian Proton launch vehicle. Findings from the analysis of the STS-126 Shuttle Endeavour window impact damage are provided. Abstracts from the NASA Orbital Debris program office are presented and address a variety of topics including: Reflectance Spectra Comparison of Orbital Debris, Intact Spacecraft, and Intact Rocket Bodies in the GEO Regime; Shape Distribution of Fragments From Microsatellite Impact Tests; Micrometeoroid and Orbital Debris Threat Mitigation Techniques for the Space Shuttle Orbiter; Space Debris Environment Remediation Concepts; and, In Situ Measurement Activities at the NASA Orbital Debris Program Office. Additionally, a Meeting Report is provided for the 12 meeting of the NASA/DoD Orbital Debris Working Group.

Preliminary volcano-hazard assessment for Mount Spurr Volcano, Alaska

USGS Publications Warehouse

Waythomas, Christopher F.; Nye, Christopher J.

2001-01-01

Mount Spurr volcano is an ice- and snow-covered stratovolcano complex located in the north-central Cook Inlet region about 100 kilometers west of Anchorage, Alaska. Mount Spurr volcano consists of a breached stratovolcano, a lava dome at the summit of Mount Spurr, and Crater Peak vent, a small stratocone on the south flank of Mount Spurr volcano. Historical eruptions of Crater Peak occurred in 1953 and 1992. These eruptions were relatively small but explosive, and they dispersed volcanic ash over areas of interior, south-central, and southeastern Alaska. Individual ash clouds produced by the 1992 eruption drifted east, north, and south. Within a few days of the eruption, the south-moving ash cloud was detected over the North Atlantic. Pyroclastic flows that descended the south flank of Crater Peak during both historical eruptions initiated volcanic-debris flows or lahars that formed temporary debris dams across the Chakachatna River, the principal drainage south of Crater Peak. Prehistoric eruptions of Crater Peak and Mount Spurr generated clouds of volcanic ash, pyroclastic flows, and lahars that extended to the volcano flanks and beyond. A flank collapse on the southeast side of Mount Spurr generated a large debris avalanche that flowed about 20 kilometers beyond the volcano into the Chakachatna River valley. The debris-avalanche deposit probably formed a large, temporary debris dam across the Chakachatna River. The distribution and thickness of volcanic-ash deposits from Mount Spurr volcano in the Cook Inlet region indicate that volcanic-ash clouds from most prehistoric eruptions were as voluminous as those produced by the 1953 and 1992 eruptions. Clouds of volcanic ash emitted from the active vent, Crater Peak, would be a major hazard to all aircraft using Ted Stevens Anchorage International Airport and other local airports and, depending on wind direction, could drift a considerable distance beyond the volcano. Ash fall from future eruptions could disrupt many types of economic and social activities, including oil and gas operations and shipping activities in the Cook Inlet area. Eruptions of Crater Peak could involve significant amounts of ice and snow that would lead to the formation of large lahars, formation of volcanic debris dams, and downstream flooding. The greatest hazards in order of importance are described below and shown on plate 1.

Analytical Modeling of Pressure Wall Hole Size and Maximum Tip-to-Tip Crack Length for Perforating Normal and Oblique Orbital Debris Impacts

NASA Technical Reports Server (NTRS)

Schonberg, William P.; Mohamed, Essam

1997-01-01

This report presents the results of a study whose objective was to develop first-principles-based models of hole size and maximum tip-to-tip crack length for a spacecraft module pressure wall that has been perforated in an orbital debris particle impact. The hole size and crack length models are developed by sequentially characterizing the phenomena comprising the orbital debris impact event, including the initial impact, the creation and motion of a debris cloud within the dual-wall system, the impact of the debris cloud on the pressure wall, the deformation of the pressure wall due to debris cloud impact loading prior to crack formation, pressure wall crack initiation, propagation, and arrest, and finally pressure wall deformation following crack initiation and growth. The model development has been accomplished through the application of elementary shock physics and thermodynamic theory, as well as the principles of mass, momentum, and energy conservation. The predictions of the model developed herein are compared against the predictions of empirically-based equations for hole diameters and maximum tip-to-tip crack length for three International Space Station wall configurations. The ISS wall systems considered are the baseline U.S. Lab Cylinder, the enhanced U.S. Lab Cylinder, and the U.S. Lab Endcone. The empirical predictor equations were derived from experimentally obtained hole diameters and crack length data. The original model predictions did not compare favorably with the experimental data, especially for cases in which pressure wall petalling did not occur. Several modifications were made to the original model to bring its predictions closer in line with the experimental results. Following the adjustment of several empirical constants, the predictions of the modified analytical model were in much closer agreement with the experimental results.

Small Orbital Stereo Tracking Camera Technology Development

NASA Technical Reports Server (NTRS)

Bryan, Tom; MacLeod, Todd; Gagliano, Larry

2017-01-01

Any exploration vehicle assembled or Spacecraft placed in LEO or GTO must pass through this debris cloud and survive. Large cross section, low thrust vehicles will spend more time spiraling out through the cloud and will suffer more impacts.Better knowledge of small debris will improve survival odds. Current estimated Density of debris at various orbital attitudes with notation of recent collisions and resulting spikes. Orbital Debris Tracking and Characterization has now been added to NASA Office of Chief Technologists Technology Development Roadmap in Technology Area 5 (TA5.7)[Orbital Debris Tracking and Characterization] and is a technical gap in the current National Space Situational Awareness necessary to safeguard orbital assets and crews due to the risk of Orbital Debris damage to ISS Exploration vehicles. The Problem: Traditional orbital trackers looking for small, dim orbital derelicts and debris typically will stare at the stars and let any reflected light off the debris integrate in the imager for seconds, thus creating a streak across the image. The Solution: The Small Tracker will see Stars and other celestial objects rise through its Field of View (FOV) at the rotational rate of its orbit, but the glint off of orbital objects will move through the FOV at different rates and directions. Debris on a head-on collision course (or close) will stay in the FOV at 14 Km per sec. The Small Tracker can track at 60 frames per sec allowing up to 30 fixes before a near-miss pass. A Stereo pair of Small Trackers can provide range data within 5-7 Km for better orbit measurements.

Stellar Debris in the Large Magellanic Cloud

NASA Image and Video Library

2006-12-08

This is a composite image of N49, the brightest supernova remnant in optical light in the Large Magellanic Cloud; the image combines data from the Chandra X-ray Telescope blue and NASA Spitzer Space Telescope red.

A violent interaction between the dwarf galaxy UGC 7636 and the giant elliptical galaxy NGC 4472

NASA Technical Reports Server (NTRS)

Mcnamara, Brian R.; Sancisi, Renzo; Henning, Patricia A.; Junor, William

1994-01-01

We present new U, B, R, and H I imagery of the Virgo Cluster giant elliptical galaxy NGC 4472 and its interacting dwarf companion galaxy UGC 7636. Using a composite image reconstruction technique, we show that a trail of debris approx. 5 arcmin in length and approx. 1 arcmin in width (30x6 kpc for a Virgo cluster distance of 20 Mpc) is projected northward from the dwarf galaxy. A cloud of H I is projected along the northwest edge of the debris between the dwarf and gE. The dwarf's nuclear morphology is irregular and bow-shaped on what appears to be its leading edge. Apart from a number of isolated blue regions, most of of the trailing debris is similar in color to the dwarf's nucleus. Only a modest enhancement of star formation appears to have been induced by the interaction. Although separated by 15 kpc, the H I and stellar morphologies are remarkably similar. The stars and H I appear to have been tidally distorted in situ, prior to the cloud's removal by ram pressure. If the H I has maintained its shape by magnetic support, a magnetic field strength an order of magnitude larger than the galaxy's is required. Ram pressure deceleration due to the cloud's motion through NGC 4472's x-ray-emitting interstellar medium shold be sufficient for the cloud to become gravitationally bound to NGC 4472. The H I cloud is not self-gravitating and may fragment and be destroyed in the interaction. UGC 7636 will probably be disrupted by NGC 4472's strong tidal forces; the stellar debris will disperse into the Virgo cluster or become bound to NGC 4472's halo on eccentric orbits. The debris captured in the collision will have a negligible impact on NGC 4472's stellar and gaseous content. On the other hand, if similar interactions are common in giant elliptical galaxies, they could alter or deplete surrounding dwarf galaxy populations, fuel bursts of nuclear activity, and perhaps provide a source of magnetic energy to their interstellar media.

Enhanced softgoods structures for spacesuit micrometeoroid/debris protective systems

NASA Technical Reports Server (NTRS)

Remington, Brian; Cadogan, David; Kosmo, Joseph

1992-01-01

A lightweight, flexible thermal micrometeoroid garment (TMG) design for enhanced space suit micrometeoroid/debris (M/D) protection is described. It will consist of an outer layer comprised of orthofabric, multilayers of aluminized Mylar, and a layer of silicone rubber loaded with micron sized particles of tungsten. The shield layers would fragment and/or vaporize the M/D projectile while the backup sheet would stop the resultant debris cloud.

CONSTELL: NASA's Satellite Constellation Model

NASA Technical Reports Server (NTRS)

Theall, Jeffrey R.; Krisko, Paula H.; Opiela, John N.; McKay, Gordon A. (Technical Monitor)

1999-01-01

The CONSTELL program represents an initial effort by the orbital debris modeling group at NASA/JSC to address the particular issues and problems raised by the presence of LEO satellite constellations. It was designed to help NASA better understand the potential orbital debris consequences of having satellite constellations operating in the future in LEO. However, it could also be used by constellation planners to evaluate architecture or design alternatives that might lessen debris consequences for their constellation or lessen the debris effects on other users of space. CONSTELL is designed to perform debris environment projections rapidly so it can support parametric assessments involving either the constellations themselves or the background environment which represents non-constellation users of the space. The projections need to be calculated quickly because a number of projections are often required to adequately span the parameter space of interest. To this end CONSTELL uses the outputs of other NASA debris environment models as inputs, thus doing away with the need for time consuming upfront calculations. Specifically, CONSTELL uses EVOLVE or ORDEM96 debris spatial density results as its background environment, debris cloud snapshot templates to simulate debris cloud propagation, and time dependent orbit profiles of the intact non- functional constellation spacecraft and upper stages. In this paper the environmental consequences of the deployment of particular LEO satellite constellations using the CONSTELL model will be evaluated. Constellations that will undergo a parametric assessment will reflect realistic parameter values. Among other results the increase in loss rate of non-constellation spacecraft, the number of collisions involving constellation elements, and the replacement rate of constellation satellites as a result of debris impact will be presented.

Using Structure-from-Motion to Quantify Sediment Accumulation and Bedrock Erosion in a Debris-Flow Dominated Channel

NASA Astrophysics Data System (ADS)

Reitman, N. G.; Rengers, F.; Kean, J. W.

2016-12-01

One of the highest frequencies of observed debris flows in the US is located at the Chalk Cliffs in central Colorado. This high rate of debris-flow activity ( 3 per year) is supported by a similarly high rate of sediment supply from rock fall and ravel due to frost weathering of the highly-erodible, hydrothermally-altered quartz monzonite cliffs during the winter months. A first step toward understanding debris-flow initiation, and channel and hillslope evolution, is to quantify the magnitude and spatial distribution of sediment that accumulates by the end of the winter period. Here we test the ability of structure-from-motion photogrammetric surveys to produce high-resolution point clouds in order to quantify sediment deposition, and possibly bedrock erosion. We use point clouds obtained from surveys conducted in late September 2015 and early June 2016 to measure sediment deposition in a 42-m-long channel over one winter. All surveys are co-registered with control points (screws drilled into bedrock) measured in a local coordinate system with a total station. Point clouds derived from these surveys have average point densities >200,000 pts/m2, and accuracies within 2 cm. Initial analysis shows accumulation of 10-50 cm ( 10 m3) of unconsolidated loose sediment over eight months, providing ample material for debris-flow initiation during the following summer season. Sediment accumulated in a spatially-variable pattern dependent on existing channel-bottom bedrock topography. Future surveys are planned in order to measure bedrock erosion by debris flows and variation in sediment deposition rate through time. Our analysis indicates that photogrammetric surveys provide a high level of detail at low cost, and thus are a useful geomorphic monitoring tool that will ultimately lead to better understanding of the processes that contribute to debris-flow activity and landscape evolution.

Cosmic dust and space debris; Proceedings of the Topical Meetings and Workshop 6 of the 26th COSPAR Plenary Meeting, Toulouse, France, June 30-July 11, 1986

NASA Technical Reports Server (NTRS)

Mcdonnell, J. A. M. (Editor); Hanner, M. S. (Editor); Kessler, D. J. (Editor)

1986-01-01

These proceedings encompass topics in the fields of extraterrestrial material samples, IRAS solar system and dust model results, and earth orbit debris. Attention is given to chemical fractionation during high velocity impact, particle deceleration and survival in multiple thin foil targets, and IRAS studies of asteroids, comets, cometary tails, the zodiacal background, and the three-dimensional modeling of interplanetary dust. Also discussed are the evolution of an earth orbit debris cloud, orbital debris due to future space activities, collision probabilities in geosynchronous orbits, and a bitelescopic survey of low altitude orbital debris.

An Imaging System for Automated Characteristic Length Measurement of Debrisat Fragments

NASA Technical Reports Server (NTRS)

Moraguez, Mathew; Patankar, Kunal; Fitz-Coy, Norman; Liou, J.-C.; Sorge, Marlon; Cowardin, Heather; Opiela, John; Krisko, Paula H.

2015-01-01

The debris fragments generated by DebriSat's hypervelocity impact test are currently being processed and characterized through an effort of NASA and USAF. The debris characteristics will be used to update satellite breakup models. In particular, the physical dimensions of the debris fragments must be measured to provide characteristic lengths for use in these models. Calipers and commercial 3D scanners were considered as measurement options, but an automated imaging system was ultimately developed to measure debris fragments. By automating the entire process, the measurement results are made repeatable and the human factor associated with calipers and 3D scanning is eliminated. Unlike using calipers to measure, the imaging system obtains non-contact measurements to avoid damaging delicate fragments. Furthermore, this fully automated measurement system minimizes fragment handling, which reduces the potential for fragment damage during the characterization process. In addition, the imaging system reduces the time required to determine the characteristic length of the debris fragment. In this way, the imaging system can measure the tens of thousands of DebriSat fragments at a rate of about six minutes per fragment, compared to hours per fragment in NASA's current 3D scanning measurement approach. The imaging system utilizes a space carving algorithm to generate a 3D point cloud of the article being measured and a custom developed algorithm then extracts the characteristic length from the point cloud. This paper describes the measurement process, results, challenges, and future work of the imaging system used for automated characteristic length measurement of DebriSat fragments.

Orbital Debris Shape and Orientation Effects on Ballistic Limits

NASA Technical Reports Server (NTRS)

Evans, Steven W.; Williamsen, Joel E.

2005-01-01

The SPHC hydrodynamic code was used to evaluate the effects of orbital debris particle shape and orientation on penetration of a typical spacecraft dual-wall shield. Impacts were simulated at near-normal obliquity at 12 km/sec. Debris cloud characteristics and damage potential are compared with those from impacts by spherical projectiles. Results of these simulations indicate the uncertainties in the predicted ballistic limits due to modeling uncertainty and to uncertainty in the impactor orientation.

The origins of Late Quaternary debris avalanche and debris flow deposits from Cofre de Perote volcano, México

USGS Publications Warehouse

Diaz-Castellon, Rodolfo; Hubbard, Bernard E.; Carrasco-Nunez, Gerardo; Rodríguez-Vargas, José Luis

2012-01-01

Cofre de Perote volcano is a compound, shield-like volcano located in the northeastern Trans-Mexican volcanic belt. Large debris avalanche and lahar deposits are associated with the evolution of Cofre. The two best preserved of these debris-avalanche and debris-flow deposits are the ∼42 ka “Los Pescados debris flow” deposit and the ∼11–13 ka “Xico avalanche” deposit, both of which display contrasting morphological and textural characteristics, source materials, origins and emplacement environments. Laboratory X-ray diffraction and visible-infrared reflectance spectroscopy were used to identify the most abundant clay, sulfate, ferric-iron, and silica minerals in the deposits, which were either related to hydrothermal alteration or chemical weathering processes. Cloud-free Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) remote sensing imagery, supporting EO-1 Hyperion image spectra, and field ground truth samples were used to map the mineralogy and distribution of hydrothermally altered rocks on the modern summit of Cofre de Perote. The results were then compared to minerals identified in the two debris-avalanche and debris-flow deposits in order to assess possible source materials and origins for the two deposits.The older Los Pescados debris-flow deposit contains mostly halloysite and hydrous silica minerals, which match the dominant mineralogy of soils and weathered volcanic deposit in the surrounding flanks of Cofre de Perote. Its source materials were most likely derived from initially noncohesive or clay-poor flows, which subsequently bulked with clay-rich valley soils and alluvium in a manner similar to lahars from Nevado del Ruiz in 1985, but on a larger scale. The younger Xico avalanche deposit contains abundant smectite, jarosite, kaolinite, gypsum, and mixed-layered illite/smectite, which are either definitely or most likely of hydrothermal alteration origin. Smectite in particular appears to be the most abundant and spectrally dominant mineral in summit ground truth samples, ASTER mapping results, Xico avalanche deposit, and an older (pre-Xico avalanche) deposit derived from collapse(s) of ancestral Cofre de Perote edifice. However, both Xico avalanche and Los Pescados debris flow deposits show some evidence of secondary, postemplacement weathering and induration, which is evident by the presence of gibbsite, and hydroxyl interlayered minerals, in addition to recently formed halloysite and hydrous silica (i.e., indurating) cements. Field-based, visible infrared image spectroscopy (VIS/IR) spectral measurements offer the possibility of distinguishing primary minerals of hydrothermal alteration origin in debris-avalanche and debris-flow deposits from those produced either by in situ chemical weathering or bulked from weathered source materials.

The Solid Rocket Motor Slag Population: Results of a Radar-Based Regressive Statistical Evaluation

NASA Technical Reports Server (NTRS)

Horstman, Matthew F.; Xu, Yu-Lin

2008-01-01

Solid rocket motor (SRM) slag has been identified as a potential source of man-made orbital debris. The possibility that SRMs (in addition to generating dust particles in the sub-millimeter range) may generate particles up to centimeters in size has caused concern regarding their contribution to the debris environment. Returned surfaces from space do not have sufficient area or exposure time to provide a clear picture of the SRM millimeter and centimeter debris population. Currently, radar observation is probably the only way to collect data showing the debris contribution from SRMs. Such observation is used to sample the debris environment, but it is difficult to obtain accurate orbital elements for the detected debris objects. NASA has developed several models to describe the different orbital debris populations, based on assumed debris production mechanisms to create clouds of debris objects that can be propagated in time. The NASA model, LEGEND (LEO-to-GEO Environment Debris), functions as a time-tested debris model for most debris sources. However, the current LEGEND model does not include contributions from the SRM population. An SRM model has recently been developed by NASA, based on purely theoretical details of SRM production and known SRM launches, but verification with hard data is needed. Because the detections of individual SRM objects cannot be deterministically separated from the total debris observed by radar, the validation of the SRM model can only be done by combining it with the LEGEND breakup model and comparing it with data. By applying observational constraints, the degree of SRM slag contribution to the environment may be estimated. This serves as an observationally sound method from which to calibrate a purely theoretical model into something more realistic. For this study, we use the populations observed by the Haystack radar from 1996 to present. For the SRM debris, we use a historical database of SRM launches, propellant masses, and estimated locations and times of tailoff to produce and propagate the SRM debris clouds. Comparisons with radar data from the ensuing years were made, and the SRM model was altered with respect to size and mass production of slag particles to reflect the populations estimated from the data. The result is a model SRM population that fits within the bounds of the observed environment and estimates of the production and contribution of SRM debris to the environment.

Capacitors Would Help Protect Against Hypervelocity Impacts

NASA Technical Reports Server (NTRS)

Edwards, David; Hubbs, Whitney; Hovater, Mary

2007-01-01

A proposal investigates alternatives to the present bumper method of protecting spacecraft against impacts of meteoroids and orbital debris. The proposed method is based on a British high-voltage-capacitance technique for protecting armored vehicles against shaped-charge warheads. A shield, according to the proposal, would include a bare metal outer layer separated by a gap from an inner metal layer covered with an electrically insulating material. The metal layers would constitute electrodes of a capacitor. A bias potential would be applied between the metal layers. A particle impinging at hypervelocity on the outer metal layer would break apart into a debris cloud that would penetrate the electrical insulation on the inner metal layer. The cloud would form a path along which electric current could flow between the metal layers, thereby causing the capacitor to discharge. With proper design, the discharge current would be large enough to vaporize the particles in the debris cloud to prevent penetration of the spacecraft. The shield design can be mass optimized to be competitive with existing bumper designs. Parametric studies were proposed to determine optimum correction between bias voltage, impacting particle velocity, gap space, and insulating material required to prevent spacecraft penetration.

Optimum structure of Whipple shield against hypervelocity impact

NASA Astrophysics Data System (ADS)

Lee, M.

2014-05-01

Hypervelocity impact of a spherical aluminum projectile onto two spaced aluminum plates (Whipple shield) was simulated to estimate an optimum structure. The Smooth Particle Hydrodynamics (SPH) code which has a unique migration scheme from a rectangular coordinate to an axisymmetic coordinate was used. The ratio of the front plate thickness to sphere diameter varied from 0.06 to 0.48. The impact velocities considered here were 6.7 km/s. This is the procedure we explored. To guarantee the early stage simulation, the shapes of debris clouds were first compared with the previous experimental pictures, indicating a good agreement. Next, the debris cloud expansion angle was predicted and it shows a maximum value of 23 degree for thickness ratio of front bumper to sphere diameter of 0.23. A critical sphere diameter causing failure of rear wall was also examined while keeping the total thickness of two plates constant. There exists an optimum thickness ratio of front bumper to rear wall, which is identified as a function of the size combination of the impacting body, front and rear plates. The debris cloud expansion-correlated-optimum thickness ratio study provides a good insight on the hypervelocity impact onto spaced target system.

Analysis and Consequences of the Iridium 33-Cosmos 2251 Collision

NASA Technical Reports Server (NTRS)

Anz-Meador, P. D.; Liou, Jer-Chi

2010-01-01

The collision of Iridium 33 and Cosmos 2251, on 10 February 2009, was the first known unintentional hypervelocity collision in space of intact satellites. Iridium 33 was an active commercial telecommunications satellite, while Cosmos 2251 was a derelict communication satellite of the Strela-2M class. The collision occurred at a relative velocity of 11.6 km/s at an altitude of approximately 790 km over the Great Siberian Plain and near the northern apex of Cosmos 2251 s orbit. This paper describes the physical and orbital characteristics of the relevant spacecraft classes and reports upon our analysis of the resulting debris clouds size, mass, area-to-mass ratio, and relative velocity/directionality distributions. We compare these distributions to those predicted by the NASA breakup model and notable recent fragmentation events; in particular, we compare the area-to-mass ratio distribution for each spacecraft to that exhibited by the FY-1C debris cloud for the purpose of assessing the relative contribution of modern aerospace materials to debris clouds resulting from energetic collisions. In addition, we examine the long-term consequences of this event for the low Earth orbit (LEO) environment. Finally, we discuss "lessons learned", which may be incorporated into NASA s environmental models.

The Effect of a Potentially Low Solar Cycle #24 on Orbital Lifetimes of Fengyun 1-C Debris

NASA Technical Reports Server (NTRS)

Whitlock, David; Johnson, Nicholas; Matney, Mark; Krisko, Paula

2008-01-01

The magnitude of Solar Cycle #24 will have a non-trivial impact on the lifetimes of debris pieces that resulted from the intentional hypervelocity impact of the Fengyun 1-C satellite in January 2007. Recent solar flux measurements indicate Solar Cycle #24 has begun in the last few months, and will continue until approximately 2019. While there have been differing opinions on whether the intensity of this solar cycle will be higher or lower than usual, the Space Weather Prediction Center within the National Oceanic Atmospheric Administration (NOAA/SWPC) has recently forecast unusually low solar activity, which would result in longer orbital lifetimes. Using models for both the breakup of Fengyun 1-C and the propagation of the resultant debris cloud, the Orbital Debris Program Office at NASA Johnson Space Center conducted a study to better understand the impact of the solar cycle on lifetimes for pieces as small as 1 mm. Using a modified collision breakup model and PROP3D propagation software, the orbits of nearly 2 million objects 1 mm and larger were propagated for up to 200 years. By comparing a normal solar cycle with that of the NOAA/SWPC forecast low cycle, the effect of the solar flux on the lifetimes of the debris pieces is evaluated. The modeling of the low solar cycle shows an additional debris count of 12% for pieces larger than 10 cm by 2019 when compared to the resultant debris count using a normal cycle. The difference becomes more exaggerated (over 15%) for debris count in the smaller size regimes. However, in 50 years, the models predict the differences in debris count from differing models of Solar Cycle #24 to be less than 10% for all size regimes, with less variance in the smaller sizes. Understanding the longevity of the debris cloud will affect collision probabilities for both operational spacecraft and large derelict objects over the next century and beyond.

Design of orbital debris shields for oblique hypervelocity impact

NASA Technical Reports Server (NTRS)

Fahrenthold, Eric P.

1994-01-01

A new impact debris propagation code was written to link CTH simulations of space debris shield perforation to the Lagrangian finite element code DYNA3D, for space structure wall impact simulations. This software (DC3D) simulates debris cloud evolution using a nonlinear elastic-plastic deformable particle dynamics model, and renders computationally tractable the supercomputer simulation of oblique impacts on Whipple shield protected structures. Comparison of three dimensional, oblique impact simulations with experimental data shows good agreement over a range of velocities of interest in the design of orbital debris shielding. Source code developed during this research is provided on the enclosed floppy disk. An abstract based on the work described was submitted to the 1994 Hypervelocity Impact Symposium.

Debris Cloud Material Characterization for Hypervelocity Impacts of Single- and Multi-Material Projectiles on Thin Target Plates

DTIC Science & Technology

1994-05-01

1979. 110 42. Williams, A.E., and Saravane, I., Debris Chlaraiatiaon SUt&y NRL Letter Rleport 4680-196,1990. 43. Weanzel, A.B., and Dean , J.K., Behind...Commerce, National Bureau of Standards, Washington, D.C., 1971. 52. Stull , D.X, and Sinke, G.C., *Thermodynamic Properties of the Elements", in Advances in

A Summary of the Evaluation of PPG Herculite XP Glass in Punched Window and Storefront Assemblies

DTIC Science & Technology

2013-01-01

frames for all IGU windows extruded from existing dies. The glazing was secured to the frame on all four sides with a 1/2-in bead width of DOW 995...lite and non-laminated IGU debris tests. A wood frame with a 4-in wide slit was placed behind the window to transform the debris cloud into a narrow...speed camera DIC Set-up laser deflection gauge shock tube window wood frame with slit high speed camerawell lit backdrop Debris Tracking Set-up laser

Atmospheric Energy Deposition Modeling and Inference for Varied Meteoroid Structures

NASA Technical Reports Server (NTRS)

Wheeler, Lorien; Mathias, Donovan; Stokan, Edward; Brown, Peter

2018-01-01

Asteroids populations are highly diverse, ranging from coherent monoliths to loosely-bound rubble piles with a broad range of material and compositional properties. These different structures and properties could significantly affect how an asteroid breaks up and deposits energy in the atmosphere, and how much ground damage may occur from resulting blast waves. We have previously developed a fragment-cloud model (FCM) for assessing the atmospheric breakup and energy deposition of asteroids striking Earth. The approach represents ranges of breakup characteristics by combining progressive fragmentation with releases of variable fractions of debris and larger discrete fragments. In this work, we have extended the FCM to also represent asteroids with varied initial structures, such as rubble piles or fractured bodies. We have used the extended FCM to model the Chelyabinsk, Benesov, Kosice, and Tagish Lake meteors, and have obtained excellent matches to energy deposition profiles derived from their light curves. These matches provide validation for the FCM approach, help guide further model refinements, and enable inferences about pre-entry structure and breakup behavior. Results highlight differences in the amount of small debris vs. discrete fragments in matching the various flare characteristics of each meteor. The Chelyabinsk flares were best represented using relatively high debris fractions, while Kosice and Benesov cases were more notably driven by their discrete fragmentation characteristics, perhaps indicating more cohesive initial structures. Tagish Lake exhibited a combination of these characteristics, with lower-debris fragmentation at high altitudes followed by sudden disintegration into small debris in the lower flares. Results from all cases also suggest that lower ablation coefficients and debris spread rates may be more appropriate for the way in which debris clouds are represented in FCM, offering an avenue for future model refinement.

Opalescent and cloudy fruit juices: formation and particle stability.

PubMed

Beveridge, Tom

2002-07-01

Cloudy fruit juices, particularly from tropical fruit, are becoming a fast-growing part of the fruit juice sector. The classification of cloud as coarse and fine clouds by centrifugation and composition of cloud from apple, pineapple, orange, guava, and lemon juice are described. Fine particulate is shown to be the true stable cloud and to contain considerable protein, carbohydrate, and lipid components. Often, tannin is present as well. The fine cloud probably arises from cell membranes and appears not to be simply cell debris. Factors relating to the stability of fruit juice cloud, including particle sizes, size distribution, and density, are described and discussed. Factors promoting stable cloud in juice are presented.

Estimated probabilities and volumes of postwildfire debris flows—A prewildfire evaluation for the Pikes Peak area, El Paso and Teller Counties, Colorado

USGS Publications Warehouse

Elliott, John G.; Ruddy, Barbara C.; Verdin, Kristine L.; Schaffrath, Keelin R.

2012-01-01

Debris flows are fast-moving, high-density slurries of water, sediment, and debris that can have enormous destructive power. Although debris flows, triggered by intense rainfall or rapid snowmelt on steep hillsides covered with erodible material, are a common geomorphic process in some unburned areas, a wildfire can transform conditions in a watershed with no recent history of debris flows into conditions that pose a substantial hazard to residents, communities, infrastructure, aquatic habitats, and water supply. The location, extent, and severity of wildfire and the subsequent rainfall intensity and duration cannot be known in advance; however, hypothetical scenarios based on empirical debris-flow models are useful planning tools for conceptualizing potential postwildfire debris flows. A prewildfire study to determine the potential for postwildfire debris flows in the Pikes Peak area in El Paso and Teller Counties, Colorado, was initiated in 2010 by the U.S. Geological Survey, in cooperation with the City of Colorado Springs, Colorado Springs Utilities. The study was conducted to provide a relative measure of which subwatersheds might constitute the most serious potential debris-flow hazards in the event of a large-scale wildfire and subsequent rainfall.

Analytic Ballistic Performance Model of Whipple Shields

NASA Technical Reports Server (NTRS)

Miller, J. E.; Bjorkman, M. D.; Christiansen, E. L.; Ryan, S. J.

2014-01-01

The dual-wall Whipple shield is the shield of choice for lightweight, long-duration flight. The shield uses an initial sacrificial wall to initiate fragmentation and melt an impacting threat that expands over a void before hitting a subsequent shield wall of a critical component. The key parameters to this type of shield are the rear wall and its mass which stops the debris, as well as the minimum pressure generated under threat particle impact of the sacrificial wall and the amount of void that is available for expansion. Ensuring the minimum pressure is sufficiently high to achieve large scale fragmentation/melt of the threat particle enables the expansion of the threat and reduces the momentum flux of the debris on the rear wall. Three key factors in the minimum pressure achieved are the thickness of the sacrificial wall relative to the characteristic dimension of the impacting particle, the density and material cohesion contrast of the sacrificial wall relative to the threat particle and the impact speed. The mass of the rear wall and the sacrificial wall are desirable to minimize for launch costs and dynamic concerns making it important to have an understanding of the effects of density contrast and impact speed. In this paper a fourth key parameter is identified related to fragmentation, which corresponds to the ratio of the size of the projectile relative to the transition from brittle to ductile hole growth in the projectile. Ballistic limit equations have been developed to define the failure limits of a MMOD shield, generally in terms of projectile diameter (or mass), impact velocity, and angle. Within the range of impact velocities relevant for Earth-orbiting spacecraft, three distinct regions of penetration phenomenology have been identified for Whipple shields: center dot Low velocity: the projectile is eroded (and possibly deformed) during its passage through the bumper plate, but is not fragmented. Thus, perforation of the rear wall is by a fragment with a mass and speed equal to or less than the original impactor. center dot Intermediate (shatter) velocity: impact velocities are sufficient to induce projectile fragmentation upon impact with the bumper plate, resulting in a coarse debris cloud with large solid fragments. Increasing velocity within the shatter regime results in increased fragmentation, and eventually melting, of the projectile and bumper fragments, generating a finer and more evenly dispersed debris cloud. Failure of the rear wall is a complicated combination of modes observed at low- and hypervelocity. center dot Hypervelocity: the projectile and holed-out bumper material is completely, or nearly completely, melted and/or vaporized by the initial impact. The resultant debris cloud impacts over a dispersed area of the rear wall, loading it impulsively and inducing failure through rupture or petalling. While each of these regimes are well observed with extensive empirical methods to describe these regions, differences in impactor materials, configurations of shields and questions about the limitations of the attainable impact speeds have left questions that are difficult to answer from completely empirical methods.

Debris Flows and Related Phenomena

NASA Astrophysics Data System (ADS)

Ancey, C.

Torrential floods are a major natural hazard, claiming thousands of lives and millions of dollars in lost property each year in almost all mountain areas on the Earth. After a catastrophic eruption of Mount St. Helen in the USA in May 1980, water from melting snow, torrential rains from the eruption cloud, and water displaced from Spirit Lake mixed with deposited ash and debris to produce very large debris flows and cause extensive damage and loss of life [1]. During the 1985 eruption of Nevado del Ruiz in Colombia, more than 20,000 people perished when a large debris flow triggered by the rapid melting of snow and ice at the volcano summit, swept through the town of Armero [2]. In 1991, the eruption of Pinatubo volcano in the Philippines disperses more than 5 cubic kilometres of volcanic ash into surrounding valleys. Much of that sediment has subsequently been mobilised as debris flows by typhoon rains and has devastated more than 300 square kilometres of agricultural land. Even, in Eur opean countries, recent events that torrential floods may have very destructive effects (Sarno and Quindici in southern Italy in May 1998, where approximately 200 people were killed). The catastrophic character of these floods in mountainous watersheds is a consequence of significant transport of materials associated with water flows. Two limiting flow regimes can be distinguished. Bed load and suspension refer to dilute transport of sediments within water. This means that water is the main agent in the flow dynamics and that the particle concentration does not exceed a few percent. Such flows are typically two-phase flows. In contrast, debris flows are mas s movements of concentrated slurries of water, fine solids, rocks and boulders. As a first approximation, debris flows can be treated as one-phase flows and their flow properties can be studied using classical rheological methods. The study of debris flows is a very exciting albeit immature science, made up of disparate elements borrowed from geomorphology, geology, hydrology, soil mechanics, and fluid mechanics. The purpose of this chapter is to provide an introduction to physical aspects of debris flows, with specific attention directed to their rheological features. Despite attempts to provide a coherent view on the topic, coverage is incomplete and the reader is referred to a series of papers and books. Three books are particularly commendable [3-5]. Some review papers provide interesting overviews, introducing the newcomers to the field to the main concepts [6-8]. The background material in rheology can be found in Chaps. 2 and 3.

The Detection of Collisional and Scattering Processes in the Asteroid-Meteoroid Continuum

NASA Astrophysics Data System (ADS)

Lai, H. R.; Connos, M. A.; Russell, C. T.; Wei, H. Y.

2014-04-01

Optical and radar observations have enabled the compilation of a useful inventory of near-Earth objects down to a diameter of approximately 500m, but at smaller diameters the catalogue is sparse. This is unacceptable for several reasons. First, the most hazardous size range based on damage per impact on Earth times expected impact rate is near 50m and second, we do not know if either the spatial distribution of objects or their behavior is similar to that of the larger objects. We have reason to believe they are importantly different. Near Earth Objects evolve due to collisions with other objects. Disruptive collisions of large objects say 200m in diameter are rare because such objects are "rare" and the impactors that could disrupt a 200m class object are rare. However, near the Earth, collisions are expected to occur at relative velocities of near 20 km/sec and such a speed could disrupt a body 106 times more massive (100 times larger diameter). Our studies show that collisions that can produce objects in the range 10 to 100m in diameter are "frequent" in near-Earth space. Our studies of the asteroid 2201 Oljato at Venus and asteroid 138175 near Earth indicates that both asteroids have coorbital debris clouds presumably caused by a past non-disruptive but debris-producing collision. This has the effect of spreading the hazardous material out of the known orbit so that a false sense of security is had when the parent body is safely past the Earth. We can detect a subset of the debris trail by their destructive impacts because they create a cloud of charged nanoscale dust which in turn creates a magnetic "cloud" that enables the dust cloud to be weighed and its location roughly identified. This shows spreading in longitude, latitude, and heliocentric radius from the parent on a time scale of decades. This is much faster than some modelers have expected and over a broader range, suggesting that the debris trail receives more of the impactor momentum than anticipated. This possibly depends on the elasticity of the target asteroid. In any event, we now have a new qualitative method of tracking debris tails of hazardous materials using existing assets in space

Comets as a possible source of nanodust in the Solar System cloud and in planetary debris discs

NASA Astrophysics Data System (ADS)

Mann, Ingrid

2017-05-01

Comets, comet-like objects and their fragments are the most plausible source for the dust in both the inner heliosphere and planetary debris discs around other stars. The smallest size of dust particles in debris discs is not known and recent observational results suggest that the size distribution of the dust extends down to sizes of a few nanometres or a few tens of nanometres. In the Solar System, electric field measurements from spacecraft observe events that are explained with high-velocity impacts of nanometre-sized dust. In some planetary debris discs an observed mid- to near-infrared emission supposedly results from hot dust located in the vicinity of the star. And the observed emission is characteristic of dust of sizes a few tens of nanometres. Rosetta observations, on the other hand, provide little information on the presence of nanodust near comet 67P/Churyumov-Gerasimenko. This article describes why this is not in contradiction to the observations of nanodust in the heliosphere and in planetary debris discs. The direct ejection of nanodust from the nucleus of the comet would not contribute significantly to the observed nanodust fluxes. We discuss a scenario that nanodust forms in the interplanetary dust cloud through the high-velocity collision process in the interplanetary medium for which the production rates are highest near the Sun. Likewise, fragmentation by collisions occurs near the star in planetary debris discs. The collisional fragmentation process in the inner Solar System occurs at similar velocities to those of the collisional evolution in the interstellar medium. A question for future studies is whether there is a common magic size of the smallest collision fragments and what determines this size. This article is part of the themed issue 'Cometary science after Rosetta'.

Simultaneous infrared and optical observations of the transiting debris cloud around WD 1145+017

NASA Astrophysics Data System (ADS)

Zhou, G.; Kedziora-Chudczer, L.; Bailey, J.; Marshall, J. P.; Bayliss, D. D. R.; Stockdale, C.; Nelson, P.; Tan, T. G.; Rodriguez, J. E.; Tinney, C. G.; Dragomir, D.; Colon, K.; Shporer, A.; Bento, J.; Sefako, R.; Horne, K.; Cochran, W.

2016-12-01

We present multiwavelength photometric monitoring of WD 1145+017, a white dwarf exhibiting periodic dimming events interpreted to be the transits of orbiting, disintegrating planetesimals. Our observations include the first set of near-infrared light curves for the object, obtained on multiple nights over the span of 1 month, and recorded multiple transit events with depths varying between ˜20 and 50 per cent. Simultaneous near-infrared and optical observations of the deepest and longest duration transit event were obtained on two epochs with the Anglo-Australian Telescope and three optical facilities, over the wavelength range of 0.5-1.2 μm. These observations revealed no measurable difference in transit depths for multiple photometric pass bands, allowing us to place a 2σ lower limit of 0.8 μm on the grain size in the putative transiting debris cloud. This conclusion is consistent with the spectral energy distribution of the system, which can be fit with an optically thin debris disc with minimum particle sizes of 10^{+5}_{-3} μm.

Long-term particle flux variability indicated by comparison of Interplanetary Dust Experiment (IDE) timed impacts for LDEF's first year in orbit with impact data for the entire 5.75-year orbital lifetime

NASA Technical Reports Server (NTRS)

Mulholland, J. Derral; Simon, Charles G.; Cooke, William J.; Oliver, John P.; Misra, V.

1992-01-01

The electronic sensors of the Interplanetary Dust Experiment (IDE) recorded precise impact times and approximate directions for submicron to approximately 100-micron size particles on all six primary sides of the spacecraft for the first 346 days of the Long Duration Exposure Facility (LDEF) orbital mission. Previously-reported analyses of the timed impact data have established their spatio-temporal features, including the demonstration that a preponderance of the particles in this regime are orbital debris and that a large fraction of the debris particles are encountered as megameter-size clouds, some of which persist for long times. Short-term fluxes within such clouds can rise several orders of magnitude above the long-term average. These finding are consistent with the results of the first catastrophic hypervelocity laboratory impacts on a real satellite, recently reported in the press. Analysis continues on the geometric and evolutionary characteristics of these clouds, as well as on the isolation and characterization of the natural micrometeoroid component in the IDE data, but the unexpectedly large short-term variations in debris flux raises the question of how representative an indication of the multi-year average flux is given by the nearly one year of timed data. It has, therefore, always been one of the goals of IDE to conduct an optical survey of the craters on the IDE detectors, to obtain full-mission fluxes for comparisons with the timed data. This work is underway, and the results presently in hand are significant. Optical scanning of the ram and wake (East and West) panels is complete, and it is clear that the first year was in some respects not representative of the subsequent years. The 5.75-year average flux on East panel was 90 percent of the value predicted by the average flux recorded during the first year, while it was only 34 percent on West panel. This suggests that western hemisphere spacecraft launches are a major contributor to the long-term flux and that their contribution is primarily in the smaller end of the size distribution. This conclusion follows from the fact that a closely-spaced series of launch failures (Titan, Delta, Ariane, and Challenger) caused a virtual hiatus in launch activity during a large part of the later years of the LDEF mission. We hope to provide a quantification of the particle size distribution function in this case.

Space Situational Awareness Data Processing Scalability Utilizing Google Cloud Services

NASA Astrophysics Data System (ADS)

Greenly, D.; Duncan, M.; Wysack, J.; Flores, F.

Space Situational Awareness (SSA) is a fundamental and critical component of current space operations. The term SSA encompasses the awareness, understanding and predictability of all objects in space. As the population of orbital space objects and debris increases, the number of collision avoidance maneuvers grows and prompts the need for accurate and timely process measures. The SSA mission continually evolves to near real-time assessment and analysis demanding the need for higher processing capabilities. By conventional methods, meeting these demands requires the integration of new hardware to keep pace with the growing complexity of maneuver planning algorithms. SpaceNav has implemented a highly scalable architecture that will track satellites and debris by utilizing powerful virtual machines on the Google Cloud Platform. SpaceNav algorithms for processing CDMs outpace conventional means. A robust processing environment for tracking data, collision avoidance maneuvers and various other aspects of SSA can be created and deleted on demand. Migrating SpaceNav tools and algorithms into the Google Cloud Platform will be discussed and the trials and tribulations involved. Information will be shared on how and why certain cloud products were used as well as integration techniques that were implemented. Key items to be presented are: 1.Scientific algorithms and SpaceNav tools integrated into a scalable architecture a) Maneuver Planning b) Parallel Processing c) Monte Carlo Simulations d) Optimization Algorithms e) SW Application Development/Integration into the Google Cloud Platform 2. Compute Engine Processing a) Application Engine Automated Processing b) Performance testing and Performance Scalability c) Cloud MySQL databases and Database Scalability d) Cloud Data Storage e) Redundancy and Availability

Stellar Winds and Dust Avalanches in the AU Mic Debris Disk

NASA Astrophysics Data System (ADS)

Chiang, Eugene; Fung, Jeffrey

2017-10-01

We explain the fast-moving, ripple-like features in the edge-on debris disk orbiting the young M dwarf AU Mic. The bright features are clouds of submicron dust repelled by the host star’s wind. The clouds are produced by avalanches: radial outflows of dust that gain exponentially more mass as they shatter background disk particles in collisional chain reactions. The avalanches are triggered from a region a few au across—the “avalanche zone”—located on AU Mic’s primary “birth” ring at a true distance of ˜35 au from the star but at a projected distance more than a factor of 10 smaller: the avalanche zone sits directly along the line of sight to the star, on the side of the ring nearest Earth, launching clouds that disk rotation sends wholly to the southeast, as observed. The avalanche zone marks where the primary ring intersects a secondary ring of debris left by the catastrophic disruption of a progenitor up to Varuna in size, less than tens of thousands of years ago. Only where the rings intersect are particle collisions sufficiently violent to spawn the submicron dust needed to seed the avalanches. We show that this picture works quantitatively, reproducing the masses, sizes, and velocities of the observed escaping clouds. The Lorentz force exerted by the wind’s magnetic field, whose polarity reverses periodically according to the stellar magnetic cycle, promises to explain the observed vertical undulations. The timescale between avalanches, about 10 yr, might be set by time variability of the wind mass loss rate or, more speculatively, by some self-regulating limit cycle.

Stellar Winds and Dust Avalanches in the AU Mic Debris Disk

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chiang, Eugene; Fung, Jeffrey, E-mail: echiang@astro.berkeley.edu, E-mail: jeffrey.fung@berkeley.edu

We explain the fast-moving, ripple-like features in the edge-on debris disk orbiting the young M dwarf AU Mic. The bright features are clouds of submicron dust repelled by the host star’s wind. The clouds are produced by avalanches: radial outflows of dust that gain exponentially more mass as they shatter background disk particles in collisional chain reactions. The avalanches are triggered from a region a few au across—the “avalanche zone”—located on AU Mic’s primary “birth” ring at a true distance of ∼35 au from the star but at a projected distance more than a factor of 10 smaller: the avalanchemore » zone sits directly along the line of sight to the star, on the side of the ring nearest Earth, launching clouds that disk rotation sends wholly to the southeast, as observed. The avalanche zone marks where the primary ring intersects a secondary ring of debris left by the catastrophic disruption of a progenitor up to Varuna in size, less than tens of thousands of years ago. Only where the rings intersect are particle collisions sufficiently violent to spawn the submicron dust needed to seed the avalanches. We show that this picture works quantitatively, reproducing the masses, sizes, and velocities of the observed escaping clouds. The Lorentz force exerted by the wind’s magnetic field, whose polarity reverses periodically according to the stellar magnetic cycle, promises to explain the observed vertical undulations. The timescale between avalanches, about 10 yr, might be set by time variability of the wind mass loss rate or, more speculatively, by some self-regulating limit cycle.« less

Debris Disks as Tracers of Nearby Planetary Systems

NASA Technical Reports Server (NTRS)

Stapelfeldt, Karl

2012-01-01

Many main-sequence stars possess tenuous circumstellar dust clouds believed to trace extrasolar analogs of the Sun's asteroid and Kuiper Belts. While most of these "debris disks" are known only from far-infrared photometry, dozens are now spatially resolved. In this talk, I'll review the observed structural properties of debris disks as revealed by imaging with the Hubble, Spitzer, and Herschel Space Telescopes. I will show how modeling of the far-infrared spectral energy distributions of resolved disks can be used to constrain their dust particle sizes and albedos. I will review cases of disks whose substructures suggest planetary perturbations, including a newly-discovered eccentric ring system. I'll conclude with thoughts on the potential of upcoming and proposed facilities to resolve similar structures around a greatly expanded sample of nearby debris systems.

Analysis of Proposed 2007-2008 Revisions to the Lightning Launch Commit Criteria for United States Space Launches

NASA Technical Reports Server (NTRS)

Dye, J. E.; Krider, E. P.; Merceret, F. J.; Willett, J. C.; Bateman, M. G.; Mach, D. M.; Rust, W. D.; Walterscheid, R.; O'Brien, T. P.; Christian, H. J.

2008-01-01

Ascending space vehicles are vulnerable to both natural and triggered lightning. Launches under the jurisdiction of the United States are generally subject to a set of rules called the Lightning Launch Commit Criteria (LLCC). The LLCC protect both the vehicle and the public by assuring that the launch does not take place in conditions posing a significant risk of a lightning strike to the ascending vehicle. Such a strike could destroy the vehicle and its payload, thus causing failure of the mission while releasing both toxic materials and debris. To assure safety, the LLCC are conservative and sometimes they may seriously limit the ability of the launch operator to fly as scheduled even when conditions are benign. In order to safely reduce the number of launch scrubs and delays attributable to the LLCC, the Airborne Field Mill (ABFM) program was undertaken in 2000 - 2001. The effort was directed to collecting detailed high-quality data on the electrical, microphysical, radar and meteorological properties of thunderstorm-associated clouds. The expectation was that this additional knowledge would provide a better physical basis for the LLCC and allow them to be revised to be both safer and less restrictive. That expectation was fulfilled, leading to significant revisions to the LLCC in 2003 and 2005. The 2005 revisions included the application of a new radar-derived quantity called the Volume Averaged Height Integrated Radar Reflectivity (VAHIRR) in the rules governing flight through anvil clouds. Analysis of the ABFM data has continued, and two additional revisions to the LLCC were proposed in late 2006 for adoption in 2007 or 2008. One proposal was to apply the VAHIRR concept to debris clouds, and the other was to reduce the "stand-off distances" in the rules for anvil and/or debris clouds. The stand-off distance is the clearance (out side of the cloud) required between the flight path of the vehicle and the edge of a cloud that it is not permissible to fly through. This paper will discuss these proposed changes in the LLCC and the scientific rationale for adopting or rejecting them based on ABFM data.

Remote sensing-based detection and quantification of roadway debris following natural disasters

NASA Astrophysics Data System (ADS)

Axel, Colin; van Aardt, Jan A. N.; Aros-Vera, Felipe; Holguín-Veras, José

2016-05-01

Rapid knowledge of road network conditions is vital to formulate an efficient emergency response plan following any major disaster. Fallen buildings, immobile vehicles, and other forms of debris often render roads impassable to responders. The status of roadways is generally determined through time and resource heavy methods, such as field surveys and manual interpretation of remotely sensed imagery. Airborne lidar systems provide an alternative, cost-effective option for performing network assessments. The 3D data can be collected quickly over a wide area and provide valuable insight about the geometry and structure of the scene. This paper presents a method for automatically detecting and characterizing debris in roadways using airborne lidar data. Points falling within the road extent are extracted from the point cloud and clustered into individual objects using region growing. Objects are classified as debris or non-debris using surface properties and contextual cues. Debris piles are reconstructed as surfaces using alpha shapes, from which an estimate of debris volume can be computed. Results using real lidar data collected after a natural disaster are presented. Initial results indicate that accurate debris maps can be automatically generated using the proposed method. These debris maps would be an invaluable asset to disaster management and emergency response teams attempting to reach survivors despite a crippled transportation network.

Celestial Fireworks

NASA Image and Video Library

2003-07-03

Resembling sparks from a fireworks display, this image taken by a JPL camera onboard NASA Hubble Space Telescope shows delicate filaments that are sheets of debris from a stellar explosion in the nearby Large Magellanic Cloud galaxy.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shaughnessy, D A; Moody, K J; Grant, P M

Collection of solid debris from the National Ignition Facility (NIF) is being developed both as a diagnostic tool and as a means for measuring nuclear reaction cross sections relevant to the Stockpile Stewardship Program and nuclear astrophysics. The concept is straightforward; following a NIF shot, the debris that is produced as a result of the capsule and hohlraum explosion would be collected and subsequently extracted from the chamber. The number of nuclear activations that occurred in the capsule would then be measured through a combination of radiation detection and radiochemical processing followed by mass spectrometry. Development of the catcher ismore » challenging due to the complex environment of the NIF target chamber. The collector surface is first exposed to a large photon flux, followed by the debris wind that is produced. The material used in the catcher must be mechanically strong in order to withstand the large amount of energy it is exposed to, as well as be chemically compatible with the form and composition of the debris. In addition, the location of the catcher is equally important. If it is positioned too close to the center of the target chamber, it will be significantly ablated, which could interfere with the ability of the debris to reach the surface and stick. If it is too far away, the fraction of the debris cloud collected will be too small to result in a statistically significant measurement. Material, geometric configuration, and location must all be tested in order to design the optimal debris collection system for NIF. One of the first ideas regarding solid debris collection at NIF was to use the disposable debris shields (DDS), which are fielded over the final optics assemblies (FOA) 7 m away from the center of the target chamber. The DDS are meant to be replaced after a certain number of shots, and if the shields could be subsequently analyzed after removal, it would serve as a mechanism for fielding a relatively large collection area through the use of a part meant to be replaced regularly. The solid angle covered by one of the shields is roughly 10{sup -4} of 4{pi}. If several shields were analyzed at once, it would increase the solid angle of the collection area accordingly. The glass shields consist of ammonia hardened silica with a sol gel coating and kapton tape around the edge. The square sheets are 14-inch on each side. The original shields were 1 mm thick, but it was determined that a thicker shield (3.3 mm) was more effective in preventing debris from reaching the FOA. The Solid Radchem group received two sets of DDS as part of our evaluation of the potential use of the DDS as solid debris collectors. The first set consisted of two 3.3 mm shields, one each from the top and bottom of the chamber (the '3mm set'). The second set consisted of four 1mm shields, one from the top of the chamber and the other three from the bottom (the 'IFSA set'). For each set, the shields were cut into smaller subsamples, which were then imaged using scanning electron microscopy (SEM) followed by chemical leaching and mass spectrometry. The purpose was to evaluate both the quantity and identity of the debris that was present on the DDS surfaces, and to determine if any of the capsule debris was reaching the chamber walls. In addition, potential enhancement due to gravity in the chamber was evaluated by directly comparing shields fielded in the top and bottom of the chamber. Based on the results, the use of the DDS as debris collectors would be evaluated. The results from both sets were presented to the DDS Working Group. The slides are attached to this document. The 3mm set results are presented first, followed by the results from the IFSA set. In both cases it was determined that a small fraction of the overall debris field was collected on the DDS. This means that the debris that is formed during a NIF shot is condensing out of the plasma and depositing on surfaces closer to the target chamber center, or else it is simply falling to the bottom of the chamber. In either case, it was determined that using the DDS, or fielding a debris collector at the chamber wall, was not feasible for solid debris collection at NIF due to the small amount of debris that had been collected. In addition, since the glass shields suffered quite a bit of damage from particles impacting the surface, glass was ruled out as a collection medium.« less

Celestial Fireworks

NASA Technical Reports Server (NTRS)

2003-01-01

Resembling sparks from a fireworks display, this image taken by a JPL camera onboard NASA's Hubble Space Telescope shows delicate filaments that are sheets of debris from a stellar explosion in the nearby Large Magellanic Cloud galaxy.

The Perils of Paul: Near Disasters in Airborne Radiochemical Sampling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meade, Roger Allen

Beginning with the Trinity test in July 1945, Laboratory radiochemists have collected debris from nuclear tests by various means. At Trinity, two United States Army Sherman tanks were used. Beginning with Operation Crossroads and continuing throughout atmospheric testing, aircraft were used to fly in and around mushroom clouds to collect debris. Paul Guthals, the LASL project leader for sampling operations, flew on many of the B-57 sampling missions. Two such missions, one flown over the Nevada Test and one in the skies near Johnston Atoll, again proved the dangers involved in collecting airborne test debris. The events of these twomore » missions are briefly recounted.« less

Logging debris matters: better soil, fewer invasive plants

Treesearch

John Kirkland; Timoth B. Harrington; David H. Peter; Robert A. Slesak; Stephen H. Schoenholtz

2012-01-01

The logging debris that remains after timber harvest traditionally has been seen as a nuisance. It can make subsequent tree planting more difficult and become fuel for wildfire. It is commonly piled, burned, or taken off site. Logging debris, however, contains significant amounts of carbon and nitrogen—elements critical to soil productivity. Its physical presence in...

Satellite Vulnerability to Space Debris- An Improved 3D Risk Assessment Methodology

NASA Astrophysics Data System (ADS)

Grassi, Lilith; Destefanis, Roberto; Tiboldo, Francesca; Donath, Therese; Winterboer, Arne; Evand, Leanne; Janovsky, Rolf; Kempf, Scott; Rudolph, Martin; Schafer, Frank; Gelhaus, Johannes

2013-08-01

The work described in the present paper, performed as a part of the PÇ-ROTECT project, presents an enhanced method to evaluate satellite vulnerability to micrometeoroids and orbital debris (MMOD), using the ESABASE2/Debris tool (developed under ESA contract). Starting from the estimation of induced failures on spacecraft (S/C) components and from the computation of lethal impacts (with an energy leading to the loss of the satellite), and considering the equipment redundancies and interactions between components, the debris-induced S/C functional impairment is assessed. The developed methodology, illustrated through its application to a case study satellite, includes the capability to estimate the number of failures on internal components, overcoming the limitations of current tools which do not allow propagating the debris cloud inside the S/C. The ballistic limit of internal equipment behind a sandwich panel structure is evaluated through the implementation of the Schäfer Ryan Lambert (SRL) Ballistic Limit Equation (BLE).

Imaging Systems for Size Measurements of Debrisat Fragments

NASA Technical Reports Server (NTRS)

Shiotani, B.; Scruggs, T.; Toledo, R.; Fitz-Coy, N.; Liou, J. C.; Sorge, M.; Huynh, T.; Opiela, J.; Krisko, P.; Cowardin, H.

2017-01-01

The overall objective of the DebriSat project is to provide data to update existing standard spacecraft breakup models. One of the key sets of parameters used in these models is the physical dimensions of the fragments (i.e., length, average-cross sectional area, and volume). For the DebriSat project, only fragments with at least one dimension greater than 2 mm are collected and processed. Additionally, a significant portion of the fragments recovered from the impact test are needle-like and/or flat plate-like fragments where their heights are almost negligible in comparison to their other dimensions. As a result, two fragment size categories were defined: 2D objects and 3D objects. While measurement systems are commercially available, factors such as measurement rates, system adaptability, size characterization limitations and equipment costs presented significant challenges to the project and a decision was made to develop our own size characterization systems. The size characterization systems consist of two automated image systems, one referred to as the 3D imaging system and the other as the 2D imaging system. Which imaging system to use depends on the classification of the fragment being measured. Both imaging systems utilize point-and-shoot cameras for object image acquisition and create representative point clouds of the fragments. The 3D imaging system utilizes a space-carving algorithm to generate a 3D point cloud, while the 2D imaging system utilizes an edge detection algorithm to generate a 2D point cloud. From the point clouds, the three largest orthogonal dimensions are determined using a convex hull algorithm. For 3D objects, in addition to the three largest orthogonal dimensions, the volume is computed via an alpha-shape algorithm applied to the point clouds. The average cross-sectional area is also computed for 3D objects. Both imaging systems have automated size measurements (image acquisition and image processing) driven by the need to quickly and accurately measure tens of thousands of debris fragments. Moreover, the automated size measurement reduces potential fragment damage/mishandling and ability for accuracy and repeatability. As the fragment characterization progressed, it became evident that the imaging systems had to be revised. For example, an additional view was added to the 2D imaging system to capture the height of the 2D object. This paper presents the DebriSat project's imaging systems and calculation techniques in detail; from design and development to maturation. The experiences and challenges are also shared.

Comets as a possible source of nanodust in the Solar System cloud and in planetary debris discs.

PubMed

Mann, Ingrid

2017-07-13

Comets, comet-like objects and their fragments are the most plausible source for the dust in both the inner heliosphere and planetary debris discs around other stars. The smallest size of dust particles in debris discs is not known and recent observational results suggest that the size distribution of the dust extends down to sizes of a few nanometres or a few tens of nanometres. In the Solar System, electric field measurements from spacecraft observe events that are explained with high-velocity impacts of nanometre-sized dust. In some planetary debris discs an observed mid- to near-infrared emission supposedly results from hot dust located in the vicinity of the star. And the observed emission is characteristic of dust of sizes a few tens of nanometres. Rosetta observations, on the other hand, provide little information on the presence of nanodust near comet 67P/Churyumov-Gerasimenko. This article describes why this is not in contradiction to the observations of nanodust in the heliosphere and in planetary debris discs. The direct ejection of nanodust from the nucleus of the comet would not contribute significantly to the observed nanodust fluxes. We discuss a scenario that nanodust forms in the interplanetary dust cloud through the high-velocity collision process in the interplanetary medium for which the production rates are highest near the Sun. Likewise, fragmentation by collisions occurs near the star in planetary debris discs. The collisional fragmentation process in the inner Solar System occurs at similar velocities to those of the collisional evolution in the interstellar medium. A question for future studies is whether there is a common magic size of the smallest collision fragments and what determines this size.This article is part of the themed issue 'Cometary science after Rosetta'. © 2017 The Author(s).

Potential postwildfire debris-flow hazards - A prewildfire evaluation for the Jemez Mountains, north-central New Mexico

Treesearch

Anne C. Tillery; Jessica Haas

2016-01-01

Wildfire can substantially increase the probability of debris flows, a potentially hazardous and destructive form of mass wasting, in landscapes that have otherwise been stable throughout recent history. Although the exact location, extent, and severity of wildfire or subsequent rainfall intensity and duration cannot be known, probabilities of fire and debris‑flow...

Limiting the immediate and subsequent hazards associated with wildfires

USGS Publications Warehouse

DeGraff, Jerome V.; Cannon, Susan H.; Parise, Mario

2013-01-01

Similarly, our capability to limit impacts from post-fire debris flows is improving. Empirical models for estimating the probability of debris-flow occurrence, the volume of such an event, and mapping the inundated area, linked with improved definitions of the rainfall conditions that trigger debris flows, can be used to provide critical information for post-fire hazard mitigation and emergency-response planning.

A piezo-bar pressure probe

NASA Technical Reports Server (NTRS)

Friend, W. H.; Murphy, C. L.; Shanfield, I.

1967-01-01

Piezo-bar pressure type probe measures the impact velocity or pressure of a moving debris cloud. It measures pressures up to 200,000 psi and peak pressures may be recorded with a total pulse duration between 5 and 65 musec.

Large impacts around a solar-analog star in the era of terrestrial planet formation.

PubMed

Meng, Huan Y A; Su, Kate Y L; Rieke, George H; Stevenson, David J; Plavchan, Peter; Rujopakarn, Wiphu; Lisse, Carey M; Poshyachinda, Saran; Reichart, Daniel E

2014-08-29

The final assembly of terrestrial planets occurs via massive collisions, which can launch copious clouds of dust that are warmed by the star and glow in the infrared. We report the real-time detection of a debris-producing impact in the terrestrial planet zone around a 35-million-year-old solar-analog star. We observed a substantial brightening of the debris disk at a wavelength of 3 to 5 micrometers, followed by a decay over a year, with quasi-periodic modulations of the disk flux. The behavior is consistent with the occurrence of a violent impact that produced vapor out of which a thick cloud of silicate spherules condensed that were then ground into dust by collisions. These results demonstrate how the time domain can become a new dimension for the study of terrestrial planet formation. Copyright © 2014, American Association for the Advancement of Science.

DUSTY OB STARS IN THE SMALL MAGELLANIC CLOUD. II. EXTRAGALACTIC DISKS OR EXAMPLES OF THE PLEIADES PHENOMENON?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adams, Joshua J.; Simon, Joshua D.; Bolatto, Alberto D.

2013-07-10

We use mid-infrared Spitzer spectroscopy and far-infrared Herschel photometry for a sample of 20 main sequence O9-B2 stars in the Small Magellanic Cloud (SMC) with strong 24 {mu}m excesses to investigate the origin of the mid-IR emission. Either debris disks around the stars or illuminated patches of dense interstellar medium (ISM) can cause such mid-IR emission. In a companion paper, Paper I, we use optical spectroscopy to show that it is unlikely for any of these sources to be classical Be stars or Herbig Ae/Be stars. We focus our analysis on debris disks and cirrus hot spots. The local, prototypemore » objects for these models are the debris disk around Vega and the heated dust cloud surrounding the stars in the Pleiades, also known as a cirrus hot spot. These two cases predict different dust masses, radii, origins, and structures, but the cleanest classification tools are lost by the poor physical resolution at the distance of the SMC. We also consider transition disks, which would have observable properties similar to debris disks. We begin classification by measuring angular extent in the highest resolution mid-IR images available. We find 3 out of 20 stars to be significantly extended, establishing them as cirrus hot spots. We then fit the IR spectral energy distributions to determine dust temperatures and masses. Analysis yields minimum grain sizes, thermal equilibrium distances, and the resultant dust mass estimates. We find the dust masses in the SMC stars to be larger than for any known debris disks. The difference in inferred properties is driven by the SMC stars being hotter and more luminous than known debris disk hosts and not in any directly observed dust properties, so this evidence against the debris disk hypothesis is circumstantial. Finally, we created a local comparison sample of bright mid-IR OB stars in the Milky Way (MW) by cross-matching the Wide-field Infrared Survey Explorer (WISE) and Hipparcos catalogs. We find that of the thousands of nearby ({<=}1 kpc) hot stars in the MW that show a mid-IR excess, only a small fraction (few percent) match the high mid-IR luminosities of the SMC stars. All such local stars in the appropriate luminosity range that can be unambiguously classified are young stars with optical emission lines or are spatially resolved by WISE with sizes too large to be plausible debris disk candidates. We conclude that the very strong mid-IR flux excesses are most likely explained as cirrus hot spots, although we cannot rigorously rule out that a small fraction of the sample is made up of debris disks or transition disks. We present suggestive evidence that bow-shock heating around runaway stars may be a contributing mechanism to the interstellar emission. These sources, interpreted as cirrus hot spots, offer a new localized probe of diffuse interstellar dust in a low metallicity environment.« less

Characterization of the cataloged Fengyun-1C fragments and their long-term effect on the LEO environment

NASA Astrophysics Data System (ADS)

Liou, J.-C.; Johnson, N. L.

2009-05-01

The intentional breakup of Fengyun-1C on 11 January 2007 created the most severe orbital debris cloud in history. The altitude where the event occurred was probably the worst location for a major breakup in the low Earth orbit (LEO) region, since it was already highly populated with operational satellites and debris generated from previous breakups. The addition of so many fragments not only poses a realistic threat to operational satellites in the region, but also increases the instability (i.e., collision cascade effect) of the debris population there. Detailed analysis of the large Fengyun-1C fragments indicates that their size and area-to-mass ratio (A/M) distributions are very different from those of other known events. About half of the fragments appear to be composed of light-weight materials and more than 100 of them have A/M values exceeding 1 m 2/kg, consistent with thermal blanket and solar panel pieces. In addition, the orbital elements of the fragments suggest non-trivial velocity gain by the fragment cloud during the impact. These important characteristics were incorporated into numerical simulations to assess the long-term impact of the Fengyun-1C fragments to the LEO debris environment. The collision probabilities between the Fengyun-1C fragments and the rest of the catalog population and the population growth in the low Earth orbit region in the next 100 years are summarized in the paper.

Numberical simulation of the effects of radially injected barium plasma in the ionosphere

NASA Technical Reports Server (NTRS)

Swift, D. W.

1985-01-01

The morphology of the ion cloud in the radial shaped charge barium injection was studied. The shape of the ion cloud that remains after the explosive products and neutral barium clears away was examined. The ion cloud which has the configuration of a rimless wagon wheel is shown. The major features are the 2.5 km radius black hole in the center of the cloud, the surrounding ring of barium ion and the spokes of barium ionization radiating away from the center. The cloud shows no evolution after it emerges from the neutral debris and it is concluded that it is formed within 5 seconds of the event. A numerical model is used to calculate the motion of ions and electrons subject to the electrostatic and lorenz forces.

A Fragment-Cloud Model for Breakup of Asteroids with Varied Internal Structures

NASA Technical Reports Server (NTRS)

Wheeler, Lorien; Mathias, Donovan; Stokan, Ed; Brown, Peter

2016-01-01

As an asteroid descends toward Earth, it deposits energy in the atmosphere through aerodynamic drag and ablation. Asteroid impact risk assessments rely on energy deposition estimates to predict blast overpressures and ground damage that may result from an airburst, such as the one that occurred over Chelyabinsk, Russia in 2013. The rates and altitudes at which energy is deposited along the entry trajectory depend upon how the bolide fragments, which in turn depends upon its internal structure and composition. In this work, we have developed an analytic asteroid fragmentation model to assess the atmospheric energy deposition of asteroids with a range of structures and compositions. The modeling approach combines successive fragmentation of larger independent pieces with aggregate debris clouds released with each fragmentation event. The model can vary the number and masses of fragments produced, the amount of mass released as debris clouds, the size-strength scaling used to increase the robustness of smaller fragments, and other parameters. The initial asteroid body can be seeded with a distribution of independent fragment sizes amid a remaining debris mass to represent loose rubble pile conglomerations, can be given an outer regolith later, or can be defined as a coherent or fractured monolith. This approach enables the model to represent a range of breakup behaviors and reproduce detailed energy deposition features such as multiple flares due to successive burst events, high-altitude regolith blow-off, or initial disruption of rubble piles followed by more energetic breakup of the constituent boulders. These capabilities provide a means to investigate sensitivities of ground damage to potential variations in asteroid structure.

A Fragment-Cloud Approach for Modeling Atmospheric Breakup of Asteroids with Varied Internal Structures

NASA Astrophysics Data System (ADS)

Wheeler, Lorien; Mathias, Donovan; NASA Engineering Risk Assessment Team, NASA Asteroid Threat Assessment Project

2016-10-01

As an asteroid descends toward Earth, it deposits energy in the atmosphere through aerodynamic drag and ablation. Asteroid impact risk assessments rely on energy deposition estimates to predict blast overpressures and ground damage that may result from an airburst, such as the one that occurred over Chelyabinsk, Russia in 2013. The rates and altitudes at which energy is deposited along the entry trajectory depend upon how the bolide fragments, which in turn depends upon its internal structure and composition. In this work, an analytic asteroid fragmentation model has been developed to model the atmospheric breakup and resulting energy deposition of asteroids with a range of internal structures. The modeling approach combines successive fragmentation of larger independent pieces with aggregate debris clouds released with each fragmentation event. The model can vary the number and masses of fragments produced, the amount of mass released as debris clouds, and the size-strength scaling used to increase the robustness of smaller fragments. The initial asteroid body can be seeded with a distribution of independent fragment sizes amid a remaining debris mass to represent loose rubble pile conglomerations, or can be defined as a monolith with an outer regolith layer. This approach enables the model to represent a range of breakup behaviors and reproduce detailed energy deposition features such as multiple flares due to successive burst events, high-altitude regolith blow-off, or initial disruption of rubble piles followed by more energetic breakup of the constituent boulders. These capabilities provide a means to investigate sensitivities of ground damage to potential variations in asteroid structure.

Is the Sky Really Falling? An Overview of Orbital Debris

NASA Technical Reports Server (NTRS)

Hull, Scott M.

2015-01-01

Orbital debris has been a prominent topic for a while, even before the movie Gravity came out. An anti-satellite test and a collision with an operational satellite both produced large highly-publicized debris clouds within recent years. While large objects like abandoned satellites and rocket bodies may be the most recognizable and identifiable concerns, a majority of the daily threat comes from the much more numerous smaller particles. In fact, small particle penetration continues to rank among the leading risks for manned space missions to the International Space Station and beyond. How much 'stuff' is up there, where did it come from, what harm can it do, and what is being done about it? These questions and more will be discussed.

Meteorological modeling of arrival and deposition of fallout at intermediate distances downwind of the Nevada Test Site.

PubMed

Cederwall, R T; Peterson, K R

1990-11-01

A three-dimensional atmospheric transport and diffusion model is used to calculate the arrival and deposition of fallout from 13 selected nuclear tests at the Nevada Test Site (NTS) in the 1950s. Results are used to extend NTS fallout patterns to intermediate downwind distances (300 to 1200 km). The radioactive cloud is represented in the model by a population of Lagrangian marker particles, with concentrations calculated on an Eulerian grid. Use of marker particles, with fall velocities dependent on particle size, provides a realistic simulation of fallout as the debris cloud travels downwind. The three-dimensional wind field is derived from observed data, adjusted for mass consistency. Terrain is represented in the grid, which extends up to 1200 km downwind of NTS and has 32-km horizontal resolution and 1-km vertical resolution. Ground deposition is calculated by a deposition-velocity approach. Source terms and relationships between deposition and exposure rate are based on work by Hicks. Uncertainty in particle size and vertical distributions within the debris cloud (and stem) allow for some model "tuning" to better match measured ground-deposition values. Particle trajectories representing different sizes and starting heights above ground zero are used to guide source specification. An hourly time history of the modeled fallout pattern as the debris cloud moves downwind provides estimates of fallout arrival times. Results for event HARRY illustrate the methodology. The composite deposition pattern for all 13 tests is characterized by two lobes extending out to the north-northeast and east-northeast, respectively, at intermediate distances from NTS. Arrival estimates, along with modeled deposition values, augment measured deposition data in the development of data bases at the county level; these data bases are used for estimating radiation exposure at intermediate distances downwind of NTS. Results from a study of event TRINITY are also presented.

Final design of a space debris removal system

NASA Technical Reports Server (NTRS)

Carlson, Erika; Casali, Steve; Chambers, Don; Geissler, Garner; Lalich, Andrew; Leipold, Manfred; Mach, Richard; Parry, John; Weems, Foley

1990-01-01

The objective is the removal of medium sized orbital debris in low Earth orbits. The design incorporates a transfer vehicle and a netting vehicle to capture the medium size debris. The system is based near an operational space station located at 28.5 degrees inclination and 400 km altitude. The system uses ground based tracking to determine the location of a satellite breakup or debris cloud. This data is unloaded to the transfer vehicle, and the transfer vehicle proceeds to rendezvous with the debris at a lower altitude parking orbit. Next, the netting vehicle is deployed, tracks the targeted debris, and captures it. After expending the available nets, the netting vehicle returns to the transfer vehicle for a new netting module and continues to capture more debris in the target area. Once all the netting modules are expended, the transfer vehicle returns to the space station's orbit, where it is resupplied with new netting modules from a space shuttle load. The new modules are launched by the shuttle from the ground, and the expended modules are taken back to Earth for removal of the captured debris, refueling, and repacking of the nets. Once the netting modules are refurbished, they are taken back into orbit for reuse. In a typical mission, the system has the ability to capture 50 pieces of orbital debris. One mission will take about six months. The system is designed to allow for a 30 degree inclination change on the outgoing and incoming trips of the transfer vehicle.

Final design of a space debris removal system

NASA Astrophysics Data System (ADS)

Carlson, Erika; Casali, Steve; Chambers, Don; Geissler, Garner; Lalich, Andrew; Leipold, Manfred; Mach, Richard; Parry, John; Weems, Foley

1990-12-01

The objective is the removal of medium sized orbital debris in low Earth orbits. The design incorporates a transfer vehicle and a netting vehicle to capture the medium size debris. The system is based near an operational space station located at 28.5 degrees inclination and 400 km altitude. The system uses ground based tracking to determine the location of a satellite breakup or debris cloud. This data is unloaded to the transfer vehicle, and the transfer vehicle proceeds to rendezvous with the debris at a lower altitude parking orbit. Next, the netting vehicle is deployed, tracks the targeted debris, and captures it. After expending the available nets, the netting vehicle returns to the transfer vehicle for a new netting module and continues to capture more debris in the target area. Once all the netting modules are expended, the transfer vehicle returns to the space station's orbit, where it is resupplied with new netting modules from a space shuttle load. The new modules are launched by the shuttle from the ground, and the expended modules are taken back to Earth for removal of the captured debris, refueling, and repacking of the nets. Once the netting modules are refurbished, they are taken back into orbit for reuse. In a typical mission, the system has the ability to capture 50 pieces of orbital debris. One mission will take about six months. The system is designed to allow for a 30 degree inclination change on the outgoing and incoming trips of the transfer vehicle.

4D-SFM Photogrammetry for Monitoring Sediment Dynamics in a Debris-Flow Catchment: Software Testing and Results Comparison

NASA Astrophysics Data System (ADS)

Cucchiaro, S.; Maset, E.; Fusiello, A.; Cazorzi, F.

2018-05-01

In recent years, the combination of Structure-from-Motion (SfM) algorithms and UAV-based aerial images has revolutionised 3D topographic surveys for natural environment monitoring, offering low-cost, fast and high quality data acquisition and processing. A continuous monitoring of the morphological changes through multi-temporal (4D) SfM surveys allows, e.g., to analyse the torrent dynamic also in complex topography environment like debris-flow catchments, provided that appropriate tools and procedures are employed in the data processing steps. In this work we test two different software packages (3DF Zephyr Aerial and Agisoft Photoscan) on a dataset composed of both UAV and terrestrial images acquired on a debris-flow reach (Moscardo torrent - North-eastern Italian Alps). Unlike other papers in the literature, we evaluate the results not only on the raw point clouds generated by the Structure-from- Motion and Multi-View Stereo algorithms, but also on the Digital Terrain Models (DTMs) created after post-processing. Outcomes show differences between the DTMs that can be considered irrelevant for the geomorphological phenomena under analysis. This study confirms that SfM photogrammetry can be a valuable tool for monitoring sediment dynamics, but accurate point cloud post-processing is required to reliably localize geomorphological changes.

An Incipient Debris Disk in the Chamaeleon I Cloud

NASA Astrophysics Data System (ADS)

Espaillat, C. C.; Ribas, Á.; McClure, M. K.; Hernández, J.; Owen, J. E.; Avish, N.; Calvet, N.; Franco-Hernández, R.

2017-07-01

The point at which a protoplanetary disk becomes a debris disk is difficult to identify. To better understand this, here we study the ˜40 au separation binary T 54 in the Chamaeleon I cloud. We derive a K5 spectral type for T 54 A (which dominates the emission of the system) and an age of ˜2 Myr. However, the dust disk properties of T 54 are consistent with those of debris disks seen around older- and earlier-type stars. At the same time, T 54 has evidence of gas remaining in the disk, as indicated by [Ne II], [Ne III], and [O I] line detections. We model the spectral energy distribution of T 54 and estimate that ˜ 3× {10}-3 {M}\\oplus of small dust grains (<0.25 μm) are present in an optically thin circumbinary disk along with at least ˜ 3× {10}-7 {M}\\oplus of larger (>10 μm) grains within a circumprimary disk. Assuming a solar-like mixture, we use Ne line luminosities to place a minimum limit on the gas mass of the disk (˜ 3× {10}-4 {M}\\oplus ) and derive a gas-to-dust mass ratio of ˜0.1. We do not detect substantial accretion, but we do see Hα in emission in one epoch, which is suggestive that there may be intermittent dumping of small amounts of matter onto the star. Considering the low dust mass, the presence of gas, and young age of T 54, we conclude that this system is on the bridge between the protoplanetary and debris disk stages.

Characterization of the catalog Fengyun-1C fragments and their long-term effect on the LEO environment

NASA Astrophysics Data System (ADS)

Liou, J.-C.

The intentional breakup of Fengyun-1C on 11 January 2007 created the most severe orbital debris cloud in history. More than 2500 large fragments were identified and tracked by the U.S. Space Surveillance Network by the end of the year. The altitude where the event occurred was probably the worst location for a major breakup in the low Earth orbit (LEO) region, since it was already highly populated with operational satellites and debris generated from previous breakups. The addition of so many fragments not only poses a realistic threat to operational satellites in the region, but also increases the instability (i.e., collision cascade effect) of the debris population there. Preliminary analysis of the large Fengyun-1C fragments indicates that their size and area-tomass ratio (A/M) distributions are very different from those of other known events. About half of the fragments appear to be composed of light-weight materials and more than 100 of them have A/M values exceeding 1 m2 /kg, consistent with thermal blanket pieces. In addition, the orbital elements of the fragments suggest non-trivial velocity gain by the fragment cloud during the impact. These important characteristics were incorporated into a numerical simulation to assess the long-term impact of the Fengyun-1C fragments to the LEO debris environment. The main objectives of the simulation were to evaluate (1) the collision probabilities between the Fengyun-1C fragments and the rest of the catalog population and (2) the collision activities and population growth in the region in the next 100 years.

Analysis of volatiles in fire debris by combination of activated charcoal strips (ACS) and automated thermal desorption-gas chromatography-mass spectrometry (ATD/GC-MS).

PubMed

Martin Fabritius, Marie; Broillet, Alain; König, Stefan; Weinmann, Wolfgang

2018-06-04

Adsorption of volatiles in gaseous phase to activated charcoal strip (ACS) is one possibility for the extraction and concentration of ignitable liquid residues (ILRs) from fire debris in arson investigations. Besides liquid extraction using carbon dioxide or hexane, automated thermo-desorption can be used to transfer adsorbed residues to direct analysis by gas chromatography-mass spectrometry (GC-MS). We present a fire debris analysis work-flow with headspace adsorption of volatiles onto ACS and subsequent automated thermo-desorption (ATD) GC-MS analysis. Only a small portion of the ACS is inserted in the ATD tube for thermal desorption coupled to GC-MS, allowing for subsequent confirmation analysis with another portion of the same ACS. This approach is a promising alternative to the routinely used ACS method with solvent extraction of retained volatiles, and the application to fire debris analysis is demonstrated. Copyright © 2018 Elsevier B.V. All rights reserved.

Atmospheric pollution measurement by optical cross correlation methods - A concept

NASA Technical Reports Server (NTRS)

Fisher, M. J.; Krause, F. R.

1971-01-01

Method combines standard spectroscopy with statistical cross correlation analysis of two narrow light beams for remote sensing to detect foreign matter of given particulate size and consistency. Method is applicable in studies of generation and motion of clouds, nuclear debris, ozone, and radiation belts.

Study on the leaching behavior of actinides from nuclear fuel debris

NASA Astrophysics Data System (ADS)

Kirishima, Akira; Hirano, Masahiko; Akiyama, Daisuke; Sasaki, Takayuki; Sato, Nobuaki

2018-04-01

For the prediction of the leaching behavior of actinides contained in the nuclear fuel debris generated by the Fukushima Daiichi nuclear power plant accident in Japan, simulated fuel debris consisting of a UO2-ZrO2 solid solution doped with 137Cs, 237Np, 236Pu, and 241Am tracers was synthesized and investigated. The synthesis of the debris was carried out by heat treatment at 1200 °C at different oxygen partial pressures, and the samples were subsequently used for leaching tests with Milli-Q water and seawater. The results of the leaching tests indicate that the leaching of actinides depends on the redox conditions under which the debris was generated; for example, debris generated under oxidative conditions releases more actinide nuclides to water than that generated under reductive conditions. Furthermore, we found that, as Zr(IV) increasingly substituted U(IV) in the fluorite crystal structure of the debris, the actinide leaching from the debris decreased. In addition, we found that seawater leached more actinides from the debris than pure water, which seems to be caused by the complexation of actinides by carbonate ions in seawater.

Numerical investigation of debris materials prior to debris flow hazards using satellite images

NASA Astrophysics Data System (ADS)

Zhang, N.; Matsushima, T.

2018-05-01

The volume of debris flows occurred in mountainous areas is mainly affected by the volume of debris materials deposited at the valley bottom. Quantitative evaluation of debris materials prior to debris flow hazards is important to predict and prevent hazards. At midnight on 7th August 2010, two catastrophic debris flows were triggered by the torrential rain from two valleys in the northern part of Zhouqu City, NW China, resulting in 1765 fatalities and huge economic losses. In the present study, a depth-integrated particle method is adopted to simulate the debris materials, based on 2.5 m resolution satellite images. In the simulation scheme, the materials are modeled as dry granular solids, and they travel down from the slopes and are deposited at the valley bottom. The spatial distributions of the debris materials are investigated in terms of location, volume and thickness. Simulation results show good agreement with post-disaster satellite images and field observation data. Additionally, the effect of the spatial distributions of the debris materials on subsequent debris flows is also evaluated. It is found that the spatial distributions of the debris materials strongly influence affected area, runout distance and flow discharge. This study might be useful in hazard assessments prior to debris flow hazards by investigating diverse scenarios in which the debris materials are unknown.

Aerosol-Assisted Solid Debris Collection for the National Ignition Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nelson, S L; Shaughnessy, D A; Moody, K J

2010-05-21

The National Ignition Facility (NIF) has been completed and has made its first shots on-target. While upcoming experiments will be focused on achieving ignition, a variety of subsequent experiments are planned for the facility, including measurement of cross sections, astrophysical measurements, and investigation of hydrodynamic instability in the target capsule. In order to successfully execute several of these planned experiments, the ability to collect solid debris following a NIF capsule shot will be required. The ability to collect and analyze solid debris generated in a shot at the National Ignition Facility (NIF) will greatly expand the number of nuclear reactionsmore » studied for diagnostic purposes. Currently, reactions are limited to only those producing noble gases for cryogenic collection and counting with the Radchem Apparatus for Gas Sampling (RAGS). The radchem solid collection diagnostic has already been identified by NIF to be valuable for the determination and understanding of mix generated in the target capsule's ablation. LLNL is currently developing this solid debris collection capability at NIF, and is in the stage of testing credible designs. Some of these designs explore the use of x-ray generated aerosols to assist in collection of solid debris. However, the variety of harsh experimental conditions this solid collection device will encounter in NIF are challenging to replicate. Experiments performed by Gary Grim et al. at Sandia National Laboratory's RHEPP1 facility have shown that ablation causes a cloud of material removed from an exposed surface to move normal to and away from the surface. This ablation is certain to be a concern in the NIF target chamber from the prompt x-rays, gamma rays, etc. generated in the shot. The cloud of ablated material could interfere with the collection of the desired reaction debris by slowing down the debris so that the kinetic energy is too low to allow implantation, or by stopping the debris from reaching the collection device entirely. Our goal is to use this primary ablation wave to our advantage, by the creation of ionized alkali metal halide salt aerosols. This technique is similar to that used by many particle accelerator groups for gas-jet transport. Ideally the salt would be ablated from a substrate, encounter the reaction debris, agglomerate, and be collected for further study. We have done studies at laser and pulsed-power facilities (Titan laser at LLNL, Trident laser at LANL, Zebra z-pinch at Nevada Terawatt Facility) evaluating the hardiness of materials for placement in the NIF target chamber, as well as testing aerosol generation by the incident x-rays generated in device shots. To test this method's potential success in the NIF environment, we have tested KCl, KI, RbI, and CsI films of 1 and 2 um linear thickness on aluminum and silicon wafer substrates in these aforementioned facilities, at varied distances. These salts do ablate in the presence of sufficient x-ray fluence. Further analysis to quantify the final ablation depth as a function of x-ray fluence is ongoing. Half of each sample was masked with a thick tungsten foil for photon opacity. KCl was the most difficult salt to ablate, from comparing the tungsten-masked side of the samples to the unmasked side of the samples. This is likely due to KCl's absorbance peak being at lower wavelengths than that of KI, {approx}160 nm vs. {approx}220 nm, respectively. Samples with and without collimation were tested to identify if any condensation of these ablated salts occurred after ablation. Visual inspection of the silicon wafer witness plates placed parallel to the direction of the incident photons showed that a vapor was deposited on the wafers next to the collimators. Further analysis with EDS in the case of the collimated samples conclusively identified the vapor as CsI. We also intend to examine samples of bare substrate exposed to the same experimental conditions for post-shot change via SEM images, optical microscopy, and atomic force microscopy (AFM). Furthermore, tests with separated isotopes may be done to reduce background contamination. When sample optimization is complete, we plan to develop a 'catcher' device for these desorbed aerosols. Current ideas include biased grids to either attract the ionized particles to the grid, or repel them towards a collection device.« less

Characterization of the Catalog Fengyun-1C Fragments and Their Long-term Effect on the LEO Environment

NASA Technical Reports Server (NTRS)

Liou, J.-C.; Johnson, N. L.

2008-01-01

The intentional breakup of Fengyun-1C on 11 January 2007 created the most severe orbital debris cloud in history. More than 2500 large fragments were identified and tracked by the U.S. Space Surveillance Network by the end of the year. The altitude where the event occurred was probably the worst location for a major breakup in the low Earth orbit (LEO) region, since it was already highly populated with operational satellites and debris generated from previous breakups. The addition of so many fragments not only poses a realistic threat to operational satellites in the region, but also increases the instability (i.e., collision cascade effect) of the debris population there. Preliminary analysis of the large Fengyun-1C fragments indicates that their size and area-to-mass ratio (A/M) distributions are very different from those of other known events. About half of the fragments appear to be composed of light-weight materials and more than 100 of them have A/M values exceeding 1 square meter per kilogram, consistent with thermal blanket pieces. In addition, the orbital elements of the fragments suggest nontrivial velocity gain by the fragment cloud during the impact. These important characteristics were incorporated into a numerical simulation to assess the long-term impact of the Fengyun-1C fragments to the LEO debris environment. The main objectives of the simulation were to evaluate (1) the collision probabilities between the Fengyun-1C fragments and the rest of the catalog population and (2) the collision activities and population growth in the region in the next 100 years.

The influence of Oort clouds on the mass and chemical balance of the interstellar medium

NASA Technical Reports Server (NTRS)

Stern, S. Alan; Shull, J. Michael

1990-01-01

The contribution of stellar encounters and interstellar erosion to comet cloud mass injection to the ISM is calculated. It is shown that evaporative mass loss from passing stars and SNe results in an average Galactic mass injection rate of up to 10 to the -5th solar mass/yr if such clouds are frequent around solar-type stars. Cometary erosion by interstellar grains produces an injection rate of 10 to the -5th to 10 to the -4th solar mass/yr. An injection rate of 2 x 10 to the -5th solar mass/yr is calculated. Each of these rates could be increased by a factor of about 15 if the comet clouds contain a significant amount of smaller debris. It is concluded that the total mass injection rate of material to the ISM by comet clouds is small compared to other ISM mass injection sources. Comet cloud mass loss to the ISM could be responsible for a sizeable fraction of the metal and dust abundances of the ISM if Oort clouds are common.

USA Space Debris Environment, Operations, and Research Updates

NASA Technical Reports Server (NTRS)

Liou, J.-C.

2018-01-01

Space Missions in 2017 Earth Satellite Population Collision Avoidance Maneuvers Post mission Disposal of U.S.A. Spacecraft Space Situational Awareness (SSA) and the Space Debris Sensor (SDS) A total of 86 space launches placed more than 400 spacecraft into Earth orbits during 2017, following the trend of increase over the past decade NASA has established conjunction assessment processes for its human spaceflight and uncrewed spacecraft to avoid accidental collisions with objects tracked by the U.S. Space Surveillance Network - NASA also assists other U.S. government spacecraft owners with conjunction assessments and subsequent maneuvers The ISS has conducted 25 debris collision avoidance maneuvers since 1999 - None in 2016-2017, but an ISS visiting vehicle had one collision avoidance maneuver in 2017 During 2017 NASA executed or assisted in the execution of 21 collision avoidance maneuvers by uncrewed spacecraft - Four maneuvers were conducted to avoid debris from Fengyun-1C - Two maneuvers were conducted to avoid debris from the collision of Cosmos 2251 and Iridium 33 - One maneuver was conducted to avoid the ISS NASA has established conjunction assessment processes for its human spaceflight and uncrewed spacecraft to avoid accidental collisions with objects tracked by the U.S. Space Surveillance Network - NASA also assists other U.S. government spacecraft owners with conjunction assessments and subsequent maneuvers The ISS has conducted 25 debris collision avoidance maneuvers since 1999 - None in 2016-2017, but an ISS visiting vehicle had one collision avoidance maneuver in 2017 During 2017 NASA executed or assisted in the execution of 21 collision avoidance maneuvers by uncrewed spacecraft - Four maneuvers were conducted to avoid debris from Fengyun-1C - Two maneuvers were conducted to avoid debris from the collision of Cosmos 2251 and Iridium 33 The 2014-15 NASA Engineering and Safety Center (NESC) study on the micrometeoroid and orbital debris (MMOD) assessment for the Joint Polar Satellite System (JPSS) provided the following findings - Millimeter-sized orbital debris pose the highest penetration risk to most operational spacecraft in LEO - The most effective means to collect direct measurement data on millimetersized debris above 600 km altitude is to conduct in situ measurements - There is currently no in situ data on such small debris above 600 km altitude Since the orbital debris population follows a power-law size distribution, there are many more millimeter-sized debris than the large tracked objects - Current conjunction assessments and collision avoidance maneuvers against the tracked objects (which are typically 10 cm and larger) only address a small fraction (<1%) of the mission-ending risk from orbital debris To address the millimeter-sized debris data gap above 600 km, NASA has recently developed an innovative in situ measurement instrument - the Space Debris Sensor (SDS) - One maneuver was conducted to avoid the ISS

Cumulus cloud venting of mixed layer ozone

NASA Technical Reports Server (NTRS)

Ching, J. K. S.; Shipley, S. T.; Browell, E. V.; Brewer, D. A.

1985-01-01

Observations are presented which substantiate the hypothesis that significant vertical exchange of ozone and aerosols occurs between the mixed layer and the free troposphere during cumulus cloud convective activity. The experiments utilized the airborne Ultra-Violet Differential Absorption Lidar (UV-DIAL) system. This system provides simultaneous range resolved ozone concentration and aerosol backscatter profiles with high spatial resolution. Evening transects were obtained in the downwind area where the air mass had been advected. Space-height analyses for the evening flight show the cloud debris as patterns of ozone typically in excess of the ambient free tropospheric background. This ozone excess was approximately the value of the concentration difference between the mixed layer and free troposphere determined from independent vertical soundings made by another aircraft in the afternoon.

Electrical Characteristics of Simulated Tornadoes and Dust Devils

NASA Technical Reports Server (NTRS)

Zimmerman, Michael I.; Farrell, William M.; Barth, E. L.; Lewellen, W. S.; Perlongo, N. J.; Jackson, T. L.

2012-01-01

It is well known that tornadoes and dust devils have the ability to accumulate significant, visible clouds of debris. Collisions between sand-like debris species produce different electric charges on different types of grains, which convect along different trajectories around the vortex. Thus, significant charge separations and electric currents are possible, which as the vortex fluctuates over time are thought to produce ULF radiation signatures that have been measured in the field. These electric and magnetic fields may contain valuable information about tornado structure and genesis, and may be critical in driving electrochemical processes within dust devils on Mars. In the present work, existing large eddy simulations of debris-laden tornadoes performed at West Virginia University are coupled with a new debris-charging and advection code developed at Goddard Space Flight Center to investigate the detailed (meter-resolution) fluid-dynamic origins of electromagnetic fields within terrestrial vortices. First results are presented, including simulations of the electric and magnetic fields that would be observed by a near-surface, instrument-laden probe during a direct encounter with a tornado.

SPECS: Orbital debris removal

NASA Technical Reports Server (NTRS)

1991-01-01

The debris problem has reached a stage at which the risk to satellites and spacecraft has become substantial in low Earth orbit (LEO). This research discovered that small particles posed little threat to spacecraft because shielding can effectively prevent these particles from damaging the spacecraft. The research also showed that, even though collision with a large piece of debris could destroy the spacecraft, the large pieces of debris pose little danger because they can be tracked and the spacecraft can be maneuvered away from these pieces. Additionally, there are many current designs to capture and remove large debris particles from the space environment. From this analysis, it was decided to concentrate on the removal of medium-sized orbital debris, that is, those pieces ranging from 1 cm to 50 cm in size. The current design incorporates a transfer vehicle and a netting vehicle to capture the medium-sized debris. The system is based near an operational space station located at 28.5 deg inclination and 400 km altitude. The system uses ground-based tracking to determine the location of a satellite breakup or debris cloud. These data are uploaded to the transfer vehicle, which proceeds to rendezvous with the debris at a lower altitude parking orbit. Next, the netting vehicle is deployed, tracks the targeted debris, and captures it. After expending the available nets, the netting vehicle returns to the transfer vehicle for a new netting module and continues to capture more debris in the target area. Once all the netting modules are expended, the transfer vehicle returns to the space station's orbit where it is resupplied with new netting modules from a space shuttle load. The new modules are launched by the shuttle from the ground and the expended modules are taken back to Earth for removal of the captured debris, refueling, and repacking of the nets. Once the netting modules are refurbished, they are taken back into orbit for reuse. In a typical mission, the system has the ability to capture 50 pieces of orbital debris. One mission will take approximately six months and the system is designed to allow for a 30 deg inclination change on the outgoing and incoming trips of the transfer vehicle.

Long-Term Evolution of the Aerosol Debris Cloud Produced by the 2009 Impact on Jupiter

NASA Technical Reports Server (NTRS)

Sanchez-Lavega, A.; Orton, G. S.; Hueso, R.; Perez-Hoyos, S.; Fletcher, L. N.; Garcia-Melendo, E.; Gomez-Forrellad, J. M.; de Pater, I.; Wong, M.; Hammel. H. B.;

Observing Strategies for Focused Orbital Debris Surveys Using the Magellan Telescope

NASA Technical Reports Server (NTRS)

Frith, James; Cowardin, Heather; Buckalew, Brent; Anz-Meador, Phillip; Lederer, Susan; Matney, Mark

2017-01-01

A breakup of the Titan 3C-17 Transtage rocket body was reported to have occurred on June 4th, 2014 at 02:38 UT by the Space Surveillance Network (SSN). Five objects were associated with this breakup and this is the fourth breakup known for this class of object. There are likely many more objects associated with this event that are not within the Space Surveillance Network's ability to detect and have not been catalogued. Several months after the breakup, observing time was obtained on the Magellan Baade 6.5 meter telescope to be used for observations of geosynchronous (GEO) space debris targets. Using the NASA Standard Satellite Breakup Model (SSBM), a simulated debris cloud of the recent Transtage breakup was produced and propagated forward in time. This provided right ascension, declination, and tracking rate predictions for where debris associated with this breakup may be more likely to be found in the sky over Magellan for our observing run. Magellan observations were then optimized using the angles and tracking rates from the model predictions to focus the search for Transtage debris. Data were collected and analysed and preliminary comparisons made between the number of objects detected and the number expected from the model. We present our results here.

In-vitro Comminution of Model Renal Calculi using Histotripsy

PubMed Central

Duryea, Alexander P.; Maxwell, Adam D.; Roberts, William W.; Xu, Zhen; Hall, Timothy L.; Cain, Charles A.

2013-01-01

Shock wave lithotripsy (SWL) suffers from the fact that it can produce residual stone fragments of significant size (>2 mm). Mechanistically, cavitation has been shown to play an important role in the reduction of such fragments to smaller debris. In this study we assessed the feasibility of using cavitationally-based pulsed ultrasound therapy (histotripsy) to erode kidney stones. Previous work has shown that histotripsy is capable of mechanically fractionating soft tissue into fine, acellular debris. Here, we investigated the potential for translating this technology to renal calculi through the use of a commonly accepted stone model, Ultracal-30 cement. Stones were sonicated using a 1-MHz focused transducer, with 5-cycle pulses delivered at a rate of 1 kHz. Pulses having peak negative pressures ranging from 3–21 MPa were tested. Results indicate that histotripsy is capable of effectively eroding the Ultracal-30 model, achieving an average stone erosion rate of 26 mg/min at maximum treatment pressure; substantial stone erosion was only observed in the presence of a dense cavitational bubble cloud. Sequential sieving of residual stone fragments indicated that debris produced by histotripsy was smaller than 100 μm in size, and treatment monitoring showed that both the cavitational bubble cloud and model stone appear as hyperechoic regions on B-mode imaging. These preliminary results indicate that histotripsy shows promise in its use for stone comminution, and an optimized erosion process may provide a potential adjunct to conventional SWL procedures. PMID:21622053

Comparison of Orbital Parameters for GEO Debris Predicted by LEGEND and Observed by MODEST: Can Sources of Orbital Debris be Identified?

NASA Technical Reports Server (NTRS)

Barker, Edwin S.; Matney, M. J.; Liou, J.-C.; Abercromby, K. J.; Rodriquez, H. M.; Seitzer, P.

2006-01-01

Since 2002 the National Aeronautics and Space Administration (NASA) has carried out an optical survey of the debris environment in the geosynchronous Earth-orbit (GEO) region with the Michigan Orbital Debris Survey Telescope (MODEST) in Chile. The survey coverage has been similar for 4 of the 5 years allowing us to follow the orbital evolution of Correlated Targets (CTs), both controlled and un-controlled objects, and Un-Correlated Targets (UCTs). Under gravitational perturbations the distributions of uncontrolled objects, both CTs and UCTs, in GEO orbits will evolve in predictable patterns, particularly evident in the inclination and right ascension of the ascending node (RAAN) distributions. There are several clusters (others have used a "cloud" nomenclature) in observed distributions that show evolution from year to year in their inclination and ascending node elements. However, when MODEST is in survey mode (field-of-view approx.1.3deg) it provides only short 5-8 minute orbital arcs which can only be fit under the assumption of a circular orbit approximation (ACO) to determine the orbital parameters. These ACO elements are useful only in a statistical sense as dedicated observing runs would be required to obtain sufficient orbital coverage to determine a set of accurate orbital elements and then to follow their evolution. Identification of the source(s) for these "clusters of UCTs" would be advantageous to the overall definition of the GEO orbital debris environment. This paper will set out to determine if the ACO elements can be used to in a statistical sense to identify the source of the "clustering of UCTs" roughly centered on an inclination of 12deg and a RAAN of 345deg. The breakup of the Titan 3C-4 transtage on February 21, 1992 has been modeled using NASA s LEGEND (LEO-to-GEO Environment Debris) code to generate a GEO debris cloud. Breakup fragments are created based on the NASA Standard Breakup Model (including fragment size, area-to-mass (A/M), and delta-V distributions). Once fragments are created, they are propagated forward in time with a subroutine GEOPROP. Perturbations included in GEOPROP are those due to solar/lunar gravity, radiation pressure, and major geopotential terms. The question to be addressed: are the UCTs detected by MODEST in this inclination/RAAN region related to the Titan 3C-4 breakup? Discussion will include the observational biases in attempting to detect a specific, uncontrolled target during given observing session. These restrictions include: (1) the length of the observing session which is 8 hours or less at any given date or declination; (2) the assumption of ACO elements for detected object when the breakup model predicts debris with non-zero eccentricities; (3) the size and illumination or brightness of the debris predicted by the model and the telescope/sky limiting magnitude.

An Extinction Probe Through the HD 107146 Debris Ring: Taking Unique Advantage of a Background Galaxy Transit

NASA Astrophysics Data System (ADS)

Schneider, Glenn

2016-10-01

We propose a 3-cycle GO program utilizing a total of HST 30 orbits to directly measure and map the line-of-sight optical depth through the brightest sector of the HD 107146 solar-analog debris ring by ring-transit differential photometry of a bright (compared to the disk), spatially extended, background galaxy. We will advantageously exploit its serendipitously unique and experiment-enabling high proper motion reflex trajectory w.r.t. the galaxy back-lighting a sectional slice the exoplanetary debris system (EDS) with a 2D grid of multiple sight-lines through the nearly face-on disk over time. These measures (the only opportunity for such in remaining HST lifetime) will uniquely provide unambiguous extinction/optical depth constraints to better elucidate the physical properties of the debris particles in this otherwise well studied EDS. With these and prior data we will: (a) disambiguate inferred particle spatial, size, and mass density distributions otherwise conflated with debris material optical property dependencies, (b) better constrain the posited pathways for planetary debris dust production mechanisms in EDSs (e.g., catastrophic collisions of parent bodies, dust-production cascades, cratering events, etc.) and (c) search for and discriminated between clumps , bumps , and clouds of collisional debris of varying particle (and mass) densities. This investigation was enabled in forethought by mapping the galaxy surface brightness out-of-transit in a comprehensive 2011 precursor study (HST GO/12228) using exactly the same STIS instrumental configuration with multi-roll PSF template subtracted coronagraphy we propose for the upcoming ring transit opportunity.

An Extinction Probe Through the HD 107146 Debris Ring: Taking Unique Advantage of a Background Galaxy Transit

NASA Astrophysics Data System (ADS)

Schneider, Glenn

2017-08-01

We propose a 3-cycle GO program utilizing a total of HST 30 orbits to directly measure and map the line-of-sight optical depth through the brightest sector of the HD 107146 solar-analog debris ring by ring-transit differential photometry of a bright (compared to the disk), spatially extended, background galaxy. We will advantageously exploit its serendipitously unique and experiment-enabling high proper motion reflex trajectory w.r.t. the galaxy back-lighting a sectional slice the exoplanetary debris system (EDS) with a 2D grid of multiple sight-lines through the nearly face-on disk over time. These measures (the only opportunity for such in remaining HST lifetime) will uniquely provide unambiguous extinction/optical depth constraints to better elucidate the physical properties of the debris particles in this otherwise well studied EDS. With these and prior data we will: (a) disambiguate inferred particle spatial, size, and mass density distributions otherwise conflated with debris material optical property dependencies, (b) better constrain the posited pathways for planetary debris dust production mechanisms in EDSs (e.g., catastrophic collisions of parent bodies, dust-production cascades, cratering events, etc.) and (c) search for and discriminated between clumps , bumps , and clouds of collisional debris of varying particle (and mass) densities. This investigation was enabled in forethought by mapping the galaxy surface brightness out-of-transit in a comprehensive 2011 precursor study (HST GO/12228) using exactly the same STIS instrumental configuration with multi-roll PSF template subtracted coronagraphy we propose for the upcoming ring transit opportunity.

Collisionless Coupling between Explosive Debris Plasma and Magnetized Ambient Plasma

NASA Astrophysics Data System (ADS)

Bondarenko, Anton

2016-10-01

The explosive expansion of a dense debris plasma cloud into relatively tenuous, magnetized, ambient plasma characterizes a wide variety of astrophysical and space phenomena, including supernova remnants, interplanetary coronal mass ejections, and ionospheric explosions. In these rarified environments, collective electromagnetic processes rather than Coulomb collisions typically mediate the transfer of momentum and energy from the debris plasma to the ambient plasma. In an effort to better understand the detailed physics of collisionless coupling mechanisms in a reproducible laboratory setting, the present research jointly utilizes the Large Plasma Device (LAPD) and the Phoenix laser facility at UCLA to study the super-Alfvénic, quasi-perpendicular expansion of laser-produced carbon (C) and hydrogen (H) debris plasma through preformed, magnetized helium (He) ambient plasma via a variety of diagnostics, including emission spectroscopy, wavelength-filtered imaging, and magnetic field induction probes. Large Doppler shifts detected in a He II ion spectral line directly indicate initial ambient ion acceleration transverse to both the debris plasma flow and the background magnetic field, indicative of a fundamental process known as Larmor coupling. Characterization of the laser-produced debris plasma via a radiation-hydrodynamics code permits an explicit calculation of the laminar electric field in the framework of a ``hybrid'' model (kinetic ions, charge-neutralizing massless fluid electrons), thus allowing for a simulation of the initial response of a distribution of He II test ions. A synthetic Doppler-shifted spectrum constructed from the simulated velocity distribution of the accelerated test ions excellently reproduces the spectroscopic measurements, confirming the role of Larmor coupling in the debris-ambient interaction.

X-Ray Imaging Study

NASA Technical Reports Server (NTRS)

OBrien, Susan K.; Workman, Gary L.

1996-01-01

The space environment in which the Space Station Freedom and other space platforms will orbit is truly a hostile environment. For example, the currently estimated integral fluence for electrons above 1 Mev at 2000 nautical miles is above 2 x 1O(exp 10) electrons/sq cm/day and the proton integral fluence is above 1 x 10(exp 9) protons/sq cm/day. At the 200 - 400 nautical miles, which is more representative of the altitude which will provide the environment for the Space Station, each of these fluences will be proportionally less; however, the data indicates that the radiation environment will obviously have an effect on structural materials exposed to the environment for long durations. The effects of this combined environment is the issue which needs to be understood for the long term exposure of structures in space. At the same time, there will be substantial potential for collisions between the space platforms and space debris. The current NASA catalogue contains over 4500 objects floating in space which are not considered payloads. This debris can have significant effects on collision with orbiting spacecraft. In order to better understand the effect of these hostile phenomena on spacecraft, several types of studies are being performed to simulate at some level the effect of the environment. In particular the study of debris clouds produced by hypervelocity impact on the various surfaces anticipated on the Space Station is very important at this point in time. The need to assess the threat of such debris clouds on space structures is an on-going activity. The Space Debris Impact facility in Building 4612 provides a test facility to monitor the types of damage produced with hypervelocity impact. These facilities are used to simulate space environmental effects from energetic particles. Flash radiography or x-ray imaging has traditionally provided such information and as such has been an important tool for recording damage in situ with the event. The proper operation of the system can provide much useful information with respect to parametric analysis of the hypervelocity experiment. The following report outlines the procedures developed to optimize the operation of the x-ray imaging system and its operational characteristics.

The increasing wildfire and post-fire debris-flow threat in western USA, and implications for consequences of climate change

USGS Publications Warehouse

Cannon, Susan H.; DeGraff, Jerry

2009-01-01

In southern California and the intermountain west of the USA, debris flows generated from recently-burned basins pose significant hazards. Increases in the frequency and size of wildfires throughout the western USA can be attributed to increases in the number of fire ignitions, fire suppression practices, and climatic influences. Increased urbanization throughout the western USA, combined with the increased wildfire magnitude and frequency, carries with it the increased threat of subsequent debris-flow occurrence. Differences between rainfall thresholds and empirical debris-flow susceptibility models for southern California and the intermountain west indicate a strong influence of climatic and geologic settings on post-fire debris-flow potential. The linkages between wildfires, debris-flow occurrence, and global warming suggests that the experiences in the western United States are highly likely to be duplicated in many other parts of the world, and necessitate hazard assessment tools that are specific to local climates and physiographies.

Woody debris in north Iberian streams: influence of geomorphology, vegetation, and management.

PubMed

Diez, J R; Elosegi, A; Pozo, J

2001-11-01

The effect of stream geomorphology, maturity, and management of riparian forests on abundance, role, and mobility of wood was evaluated in 20 contrasting reaches in the Agüera stream catchment (northern Iberian Peninsula). During 1 year the volume of woody debris exceeding 1 cm in diameter was measured in all reaches. All large woody debris (phi > 5 cm) pieces were tagged, their positions mapped, and their subsequent changes noted. Volume of woody debris was in general low and ranged from 40 to 22,000 cm3 m-2; the abundance of debris dams ranged from 0 to 5.5 per 100 m of channel. Wood was especially rare and unstable in downstream reaches, or under harvested forests (both natural or plantations). Results stress that woody debris in north Iberian streams has been severely reduced by forestry and log removal. Because of the important influence of woody debris on structure and function of stream systems, this reduction has likely impacted stream communities. Therefore, efforts to restore north Iberian streams should include in-channel and riparian management practices that promote greater abundance and stability of large woody debris whenever possible.

Environmental Effects of an Impact-Generated Dust Cloud: Implications for the Cretaceous-Tertiary Extinctions

NASA Astrophysics Data System (ADS)

Pollack, James B.; Toon, Owen B.; Ackerman, Thomas P.; McKay, Christopher P.; Turco, Richard P.

1983-01-01

A model of the evolution and radiative effects of a debris cloud from a hypothesized impact event at the Cretaceous-Tertiary boundary suggests that the cloud could have reduced the amount of light at the earth's surface below that required for photosynthesis for several months and, for a somewhat shorter interval, even below that needed for many animals to see. For 6 months to 1 year, the surface would cool; the oceans would cool only a few degrees Celsius at most, but the continents might cool a maximum of 40 Kelvin. Extinctions in the ocean may have been caused primarily by the temporary cessation of photosynthesis, but those on land may have been primarily induced by a combination of lowered temperatures and reduced light.

Environmental effects of an impact-generated dust cloud - Implications for the Cretaceous-Tertiary extinctions

NASA Technical Reports Server (NTRS)

Pollack, J. B.; Toon, O. B.; Ackerman, T. P.; Mckay, C. P.; Turco, R. P.

1983-01-01

A model of the evolution and radiative effects of a debris cloud from a hypothesized impact event at the Cretaceous-Tertiary boundary suggests that the cloud could have reduced the amount of light at the earth's surface below that required for photosynthesis for several months and, for a somewhat shorter interval, even below that needed for many animals to see. For 6 months to 1 year, the surface would cool; the oceans could cool only a few degrees Celsius at most, but the continents might cool a maximum of 40 Kelvin. Extinctions in the ocean may have been caused primarily by the temporary cessation of photosynthesis, but those on land may have been primarily induced by a combination of lowered temperatures and reduced light.

SMACK: A New Algorithm for Modeling Collisions and Dynamics of Planetesimals in Debris Disks

NASA Technical Reports Server (NTRS)

Nesvold, Erika Rose; Kuchner, Marc J.; Rein, Hanno; Pan, Margaret

2013-01-01

We present the Superparticle Model/Algorithm for Collisions in Kuiper belts and debris disks (SMACK), a new method for simultaneously modeling, in 3-D, the collisional and dynamical evolution of planetesimals in a debris disk with planets. SMACK can simulate azimuthal asymmetries and how these asymmetries evolve over time. We show that SMACK is stable to numerical viscosity and numerical heating over 10(exp 7) yr, and that it can reproduce analytic models of disk evolution. We use SMACK to model the evolution of a debris ring containing a planet on an eccentric orbit. Differential precession creates a spiral structure as the ring evolves, but collisions subsequently break up the spiral, leaving a narrower eccentric ring.

OPERATION DOMINIC, FISH BOWL SERIES. Project Officer’s Report. Project 6.2. Gamma-Ray Scanning of Debris Cloud

DTIC Science & Technology

1985-09-01

Astro Corporation (AGAC) The superheterodyne receiver operated In the 5,400- to 5,900-Mc frequency band. The receiver sensitivity was -65 dbm over...212 km—, \\ ^V^C \\ \\ 0^\\ 223 km-7Y A ^ fX / 4>^ ,♦ v 1 6L / 8.000 / S

Hypervelocity Impact Analysis of International Space Station Whipple and Enhanced Stuffed Whipple Shields

DTIC Science & Technology

2004-12-01

29 Figure 6. Flash Radiography Images of the Debris Cloud and Ejecta...hand, are not predictable. Explosions can occur because of the inadvertent mixing of propellant and oxidizer or the over-pressurization of...residual propellant due to spacecraft heating. Over-pressurized batteries may also cause explosions. Based on statistical analysis of known hypervelocity

Physical Simulation of a Prolonged Plasma-Plume Exposure of a Space Debris Object

NASA Astrophysics Data System (ADS)

Shuvalov, V. A.; Gorev, N. B.; Tokmak, N. A.; Kochubei, G. S.

2018-05-01

A methodology has been developed for the physical (laboratory) simulation of the prolonged exposure of a space debris object to high-energy ions of a plasma plume for removing the object into low-Earth orbit with its subsequent burning in the Earth's atmosphere. The methodology is based on the equivalence criteria of two modes of exposure (in the Earth's ionosphere and in the setup) and the procedure for accelerated resource tests in terms of the sputtering of the space debris material and its deceleration by a plasma jet in the Earth's ionosphere.

Determining Distributed Ablation over Dirty Ice Areas of Debris-covered Glaciers Using a UAV-SfM Approach

NASA Astrophysics Data System (ADS)

Woodget, A.; Fyffe, C. L.; Kirkbride, M. P.; Deline, P.; Westoby, M.; Brock, B. W.

2017-12-01

Dirty ice areas (where debris cover is discontinuous) are often found on debris-covered glaciers above the limit of continuous debris and are important because they are areas of high melt and have been recognized as the locus of the identified upglacier increase in debris cover. The modelling of glacial ablation in areas of dirty ice is in its infancy and is currently restricted to theoretical studies. Glacial ablation is traditionally determined at point locations using stakes drilled into the ice. However, in areas of dirty ice, ablation is highly spatially variable, since debris a few centimetres thick is near the threshold between enhancing and reducing ablation. As a result, it is very difficult to ascertain if point ablation measurements are representative of ablation of the area surrounding the stake - making these measurements unsuitable for the validation of models of dirty ice ablation. This paper aims to quantify distributed ablation and its relationship to essential dirty ice characteristics with a view to informing the construction of dirty ice melt models. A novel approach to determine distributed ablation is presented which uses repeat aerial imagery acquired from a UAV (Unmanned Aerial Vehicle), processed using SfM (Structure from Motion) techniques, on an area of dirty ice on Miage Glacier, Italian Alps. A spatially continuous ablation map is presented, along with a correlation to the local debris characteristics. Furthermore, methods are developed which link ground truth data on the percentage debris cover, albedo and clast depth to the UAV imagery, allowing these characteristics to be determined for the entire study area, and used as model inputs. For example, debris thickness is determined through a field relationship with clast size, which is then correlated with image texture and point cloud roughness metrics derived from the UAV imagery. Finally, we evaluate the potential of our novel approach to lead to improved modelling of dirty ice ablation.

Potential postwildfire debris-flow hazards - a prewildfire evaluation for the Sandia and Manzano Mountains and surrounding areas, central New Mexico

Treesearch

Anne C. Tillery; Jessica R. Haas; Lara W. Miller; Joe H. Scott; Matthew P. Thompson

2014-01-01

Wildfire can drastically increase the probability of debris flows, a potentially hazardous and destructive form of mass wasting, in landscapes that have otherwise been stable throughout recent history. Although there is no way to know the exact location, extent, and severity of wildfire, or the subsequent rainfall intensity and duration before it happens, probabilities...

Incubation of Phytophthora ramorum-infested leaf debris in soil affects survival, sporulation capacity, and subsequent risk of epidemic development within nurseries

Treesearch

Ebba K. Peterson; Niklaus J. Grünwald; Jennifer L. Parke

2017-01-01

Soilborne inoculum (infested leaf debris which has become incorporated into the soil) may be an important contributor to the persistence of the sudden oak death pathogen Phytophthora ramorum in recurrently positive nurseries. To initiate new epidemics, soilborne inoculum must not only be able to survive over time, but also be capable of producing...

Debris-flow generation from recently burned watersheds

USGS Publications Warehouse

Cannon, S.H.

2001-01-01

Evaluation of the erosional response of 95 recently burned drainage basins in Colorado, New Mexico and southern California to storm rainfall provides information on the conditions that result in fire-related debris flows. Debris flows were produced from only 37 of 95 (~40 percent) basins examined; the remaining basins produced either sediment-laden streamflow or no discernable response. Debris flows were thus not the prevalent response of the burned basins. The debris flows that did occur were most frequently the initial response to significant rainfall events. Although some hillslopes continued to erode and supply material to channels in response to subsequent rainfall events, debris flows were produced from only one burned basin following the initial erosive event. Within individual basins, debris flows initiated through both runoff and infiltration-triggered processes. The fact that not all burned basins produced debris flows suggests that specific geologic and geomorphic conditions may control the generation of fire-related debris flows. The factors that best distinguish between debris-flow producing drainages and those that produced sediment-laden streamflow are drainage-basin morphology and lithology, and the presence or absence of water-repellent soils. Basins underlain by sedimentary rocks were most likely to produce debris flows that contain large material, and sand- and gravel-dominated flows were generated primarily from terrain underlain by decomposed granite. Basin-area and relief thresholds define the morphologic conditions under which both types of debris flows occur. Debris flows containing large material are more likely to be produced from basins without water-repellent soils than from basins with water repellency. The occurrence of sand-and gravel-dominated debris flows depends on the presence of water-repellent soils.

Hypervelocity impact shield

NASA Technical Reports Server (NTRS)

Cour-Palais, Burton G. (Inventor); Crews, Jeanne Lee (Inventor)

1991-01-01

A hypervelocity impact shield and method for protecting a wall structure, such as a spacecraft wall, from impact with particles of debris having densities of about 2.7 g/cu cm and impact velocities up to 16 km/s are disclosed. The shield comprises a stack of ultra thin sheets of impactor disrupting material supported and arranged by support means in spaced relationship to one another and mounted to cover the wall in a position for intercepting the particles. The sheets are of a number and spacing such that the impacting particle and the resulting particulates of the impacting particle and sheet material are successively impact-shocked to a thermal state of total melt and/or vaporization to a degree as precludes perforation of the wall. The ratio of individual sheet thickness to the theoretical diameter of particles of debris which may be of spherical form is in the range of 0.03 to 0.05. The spacing between adjacent sheets is such that the debris cloud plume of liquid and vapor resulting from an impacting particle penetrating a sheet does not puncture the next adjacent sheet prior to the arrival thereat of fragment particulates of sheet material and the debris particle produced by a previous impact.

Estimating the aerodynamic roughness of debris covered glacier ice

NASA Astrophysics Data System (ADS)

Quincey, Duncan; Smith, Mark; Rounce, David; Ross, Andrew; King, Owen; Watson, Scott

2017-04-01

Aerodynamic roughness length (z0), the height above the ground surface at which the extrapolated horizontal wind velocity profile drops to zero, is one of the most poorly parameterised elements of the glacier surface energy balance equation. Microtopographic methods for estimating z0 are becoming increasingly well used, but are rarely validated against independent measures and are yet to be comprehensively analysed for scale or data resolution dependency. Here, we present the results of a field investigation conducted on the debris covered Khumbu Glacier during the post-monsoon season of 2015. We focus on two sites. The first is characterised by gravels and cobbles supported by a fine sandy matrix. The second comprises cobbles and boulders separated by voids. Vertical profiles of wind speed measured over both sites enable us to derive measurements of aerodynamic roughness that reflect their observed surface characteristics (0.0184 m vs 0.0243 m). z0 at the second site also varied through time following snowfall (0.0055 m) and during its subsequent melt (0.0129 m), showing the importance of fine resolution topography for near-surface airflow. We conducted Structure from Motion Multi-View Stereo (SfM-MVS) surveys across each patch and calculated z0 using three microtopographic methods. The fully three-dimensional cloud-based approach is shown to be most stable across different scales and these z0 values are most correct in relative order when compared to the wind tower data. Popular profile-based methods perform less well providing highly variable values across different scales and when using data of differing resolution.

Quantifying ice cliff contribution to debris-covered glacier mass balance from multiple sensors

NASA Astrophysics Data System (ADS)

Brun, Fanny; Wagnon, Patrick; Berthier, Etienne; Kraaijenbrink, Philip; Immerzeel, Walter; Shea, Joseph; Vincent, Christian

2017-04-01

Ice cliffs on debris-covered glaciers have been recognized as a hot spot for glacier melt. Ice cliffs are steep (even sometimes overhanging) and fast evolving surface features, which make them challenging to monitor. We surveyed the topography of Changri Nup Glacier (Nepalese Himalayas, Everest region) in November 2015 and 2016 using multiple sensors: terrestrial photogrammetry, Unmanned Aerial Vehicle (UAV) photogrammetry, Pléiades stereo images and ASTER stereo images. We derived 3D point clouds and digital elevation models (DEMs) following a Structure-from-Motion (SfM) workflow for the first two sets of data to monitor surface elevation changes and calculate the associated volume loss. We derived only DEMs for the two last data sets. The derived DEMs had resolutions ranging from < 5 cm to 30 m. The derived point clouds and DEMs are used to quantify the ice melt of the cliffs at different scales. The very high resolution SfM point clouds, together with the surface velocity field, will be used to calculate the volume losses of 14 individual cliffs, depending on their size, aspect or the presence of supra glacial lake. Then we will extend this analysis to the whole glacier to quantify the contribution of ice cliff melt to the overall glacier mass balance, calculated with the UAV and Pléiades DEMs. This research will provide important tools to evaluate the role of ice cliffs in regional mass loss.

Proceedings of Propulsion and Energetics Panel Symposium (71st) on Engine Condition Monitoring - Technology and Experience Held in Quebec City, Canada on 30 May-3 Jun 1988

DTIC Science & Technology

1988-06-03

S. This is 23.0030 US S per aircraft and year. A310/A300-600 Engine Condition Monitorig U 45000 a 4 37A 4a 4. - -n 2500 1.0 a F ig. 3 COSTS/SAVINGS...to correct for variations in the background caused by disturbances such as vapor clouds in the field of view creating scattering or obscuration...in the signal characteristics. Fine debris tends to travel with the airstream in a cloud , and larger flakes and particles become more dispersed because

Substantial reservoirs of molecular hydrogen in the debris disks around young stars.

PubMed

Thi, W F; Blake, G A; van Dishoeck, E F; van Zadelhoff, G J; Horn, J M; Becklin, E E; Mannings, V; Sargent, A I; van Den Ancker, M E; Natta, A

2001-01-04

Circumstellar accretion disks transfer matter from molecular clouds to young stars and to the sites of planet formation. The disks observed around pre-main-sequence stars have properties consistent with those expected for the pre-solar nebula from which our own Solar System formed 4.5 Gyr ago. But the 'debris' disks that encircle more than 15% of nearby main-sequence stars appear to have very small amounts of gas, based on observations of the tracer molecule carbon monoxide: these observations have yielded gas/dust ratios much less than 0.1, whereas the interstellar value is about 100 (ref. 9). Here we report observations of the lowest rotational transitions of molecular hydrogen (H2) that reveal large quantities of gas in the debris disks around the stars beta Pictoris, 49 Ceti and HD135344. The gas masses calculated from the data are several hundreds to a thousand times greater than those estimated from the CO observations, and yield gas/dust ratios of the same order as the interstellar value.

Theoretical analysis of tsunami generation by pyroclastic flows

USGS Publications Warehouse

Watts, P.; Waythomas, C.F.

2003-01-01

Pyroclastic flows are a common product of explosive volcanism and have the potential to initiate tsunamis whenever thick, dense flows encounter bodies of water. We evaluate the process of tsunami generation by pyroclastic flow by decomposing the pyroclastic flow into two components, the dense underflow portion, which we term the pyroclastic debris flow, and the plume, which includes the surge and coignimbrite ash cloud parts of the flow. We consider five possible wave generation mechanisms. These mechanisms consist of steam explosion, pyroclastic debris flow, plume pressure, plume shear, and pressure impulse wave generation. Our theoretical analysis of tsunami generation by these mechanisms provides an estimate of tsunami features such as a characteristic wave amplitude and wavelength. We find that in most situations, tsunami generation is dominated by the pyroclastic debris flow component of a pyroclastic flow. This work presents information sufficient to construct tsunami sources for an arbitrary pyroclastic flow interacting with most bodies of water. Copyright 2003 by the American Geophysical Union.

Meteoroid-bumper interactions program

NASA Technical Reports Server (NTRS)

Gough, P. S.

1970-01-01

An investigation has been made of the interaction of meteoroids with shielded structures. The interaction has been simulated by the impact of Lexan cylinders onto lead shields in order to provide the vaporous debris believed to be created by meteoroid impact on a space vehicle. Shock compression data for Lexan was determined. This, in combination with the known shock compression data for the lead shield, has permitted the definition of the initial high pressure states in the impacted projectile and shield. The debris from such impact events has been permitted to interact with aluminum main walls. The walls were chosen to be sufficiently large to be effectively infinite in diameter compared to the loaded area. The thickness of the wall and the spacing from the shield were varied to determine the effect of these parameters. In addition, the effect of having a body of water behind the wall has been assessed. Measurements of the stagnation pressure in the debris cloud have been made and correlated with the response of the main wall.

Direct imaging of an asymmetric debris disk in the HD 106906 planetary system

DOE PAGES

Kalas, Paul G.; Rajan, Abhijith; Wang, Jason J.; ...

2015-11-13

Here, we present the first scattered light detections of the HD 106906 debris disk using the Gemini/Gemini Planet Imager in the infrared and Hubble Space Telescope (HST)/Advanced Camera for Surveys in the optical. HD 106906 is a 13 Myr old F5V star in the Sco–Cen association, with a previously detected planet-mass candidate HD 106906b projected 650 AU from the host star. Our observations reveal a near edge-on debris disk that has a central cleared region with radius ~50 AU, and an outer extent >500 AU. The HST data show that the outer regions are highly asymmetric, resembling the "needle" morphologymore » seen for the HD 15115 debris disk. The planet candidate is oriented ~21° away from the position angle of the primary's debris disk, strongly suggesting non-coplanarity with the system. We hypothesize that HD 106906b could be dynamically involved in the perturbation of the primary's disk, and investigate whether or not there is evidence for a circumplanetary dust disk or cloud that is either primordial or captured from the primary. In conclusion, we show that both the existing optical properties and near-infrared colors of HD 106906b are weakly consistent with this possibility, motivating future work to test for the observational signatures of dust surrounding the planet.« less

Using Google Earth To Interpret The Southern Taiwan Hsiaolin Village Catastrophe

NASA Astrophysics Data System (ADS)

Lin, Y. H.; Huang, C. M.; Keck, J.; Wei, L. W.; Pan, K. L.

2012-04-01

The August, 2009 Typhoon Morakot resulted in accumulated rainfalls exceeding 2000 mm and the triggering of a massive debris flow that buried Hsiaolin village. Hundreds of people were killed and both domestic and international natural disaster prevention agencies took note of this large scale disaster that was not prevented. Interpretation of Google Earth satellite images reveals that the Hsiaolin debris flow originated in a single location and then split into two parts. The northern debris flow, the smaller of the two parts, flowed within a ravine. The southern part of the debris flow, much larger than the northern part, was responsible for the burial of Hsiaolin village. The movement of the debris flow can be divided into three processes. First a slope failure and subsequent debris flow occurred within a curved ravine. Second, the debris flow eroded the bank of the ravine laterally, causing translational failure of the ravine walls. A massive debris flow, made up of a combination of materials from both the original debris flow and the ravine walls, jammed within the ravine. Finally, as a result of the jam, the debris flow was redirected towards Hsiaolin village. Overlaying locations of the post-Hsiaolin debris flow landforms on top of pre-failure satellite images reveals that characteristics of the post failure landforms match perfectly with characteristics observed in the pre-failure satellite images. This finding supports the thought that large scale geologic disasters are reoccurring. This finding also suggests that areas near villages can use simple satellite image analysis to rapidly identify ancient landslides and that such information may help early evacuation planning. With such planning, property and life losses due to natural disasters can be reduced. Key word: Hsiaolin Village, Debris Flow, Remote Sensing, Image Interpretation, Cause of Disaster, Disaster Recovery, Deep-Seated Landslide, Ancient Debris Flow

Giant impacts on giant planets

NASA Astrophysics Data System (ADS)

de Pater, Imke

2017-08-01

The 2009 impact and recent superbolides on Jupiter caught the world by surprise and cast doubt on impactor flux estimates for the outer solar system. Enhanced amateur planetary imaging techniques yield both high spatial resolution (enabling the 2009 impact debris field detection) and rapid frame rates (enabling the 2010/2012 impact flash detections and lightcurve measurements).We propose a ToO program to image future impacts on Jupiter and Saturn. To remove the possibility of impact cloud non-detections, the program will be triggered only if an existing impact debris field is seen, an object on a collision course with Jupiter or Saturn is discovered, or an impact light curve is measured with an estimated total energy large enough to generate an impact cloud in a giant planet atmosphere (10^19 J).HST provides the only way to image these events in the ultraviolet, providing information on aerosol altitudes and on smaller particles that are less visible to ground-based infrared observations. High-resolution imaging with proper timing (not achievable from the ground) is required to measure precisely both the velocity fields of impact sites and the optical spectrum of impact debris. HST observations of past impacts on Jupiter have also served both as cornerstones of science investigations at other wavelengths and as vehicles for effective public outreach.Large outer solar system impacts are governed by the same physics as in the terrestrial events that dominate the impact threat to humans. Studying the behavior of impactors of various sizes and compositions, as they enter the atmosphere at varying angles and speeds, will better quantify terrestrial impact hazards.

Potential postwildfire debris-flow hazards: a prewildfire evaluation for the Sandia and Manzano Mountains and surrounding areas, central New Mexico

USGS Publications Warehouse

Tillery, Anne C.; Haas, Jessica R.; Miller, Lara W.; Scott, Joe H.; Thompson, Matthew P.

2014-01-01

Wildfire can drastically increase the probability of debris flows, a potentially hazardous and destructive form of mass wasting, in landscapes that have otherwise been stable throughout recent history. Although there is no way to know the exact location, extent, and severity of wildfire, or the subsequent rainfall intensity and duration before it happens, probabilities of fire and debris-flow occurrence for different locations can be estimated with geospatial analysis and modeling efforts. The purpose of this report is to provide information on which watersheds might constitute the most serious, potential, debris-flow hazards in the event of a large-scale wildfire and subsequent rainfall in the Sandia and Manzano Mountains. Potential probabilities and estimated volumes of postwildfire debris flows in the unburned Sandia and Manzano Mountains and surrounding areas were estimated using empirical debris-flow models developed by the U.S. Geological Survey in combination with fire behavior and burn probability models developed by the U.S. Department of Agriculture Forest Service. The locations of the greatest debris-flow hazards correlate with the areas of steepest slopes and simulated crown-fire behavior. The four subbasins with the highest computed debris-flow probabilities (greater than 98 percent) were all in the Manzano Mountains, two flowing east and two flowing west. Volumes in sixteen subbasins were greater than 50,000 square meters and most of these were in the central Manzanos and the western facing slopes of the Sandias. Five subbasins on the west-facing slopes of the Sandia Mountains, four of which have downstream reaches that lead into the outskirts of the City of Albuquerque, are among subbasins in the 98th percentile of integrated relative debris-flow hazard rankings. The bulk of the remaining subbasins in the 98th percentile of integrated relative debris-flow hazard rankings are located along the highest and steepest slopes of the Manzano Mountains. One of the subbasins is several miles upstream from the community of Tajique and another is several miles upstream from the community of Manzano, both on the eastern slopes of the Manzano Mountains. This prewildfire assessment approach is valuable to resource managers because the analysis of the debris-flow threat is made before a wildfire occurs, which facilitates prewildfire management, planning, and mitigation. In northern New Mexico, widespread watershed restoration efforts are being carried out to safeguard vital watersheds against the threat of catastrophic wildfire. This study was initiated to help select ideal locations for the restoration efforts that could have the best return on investment.

Linking rainfall-induced landslides with debris flows runout patterns towards catchment scale hazard assessment

NASA Astrophysics Data System (ADS)

Fan, Linfeng; Lehmann, Peter; McArdell, Brian; Or, Dani

2017-03-01

Debris flows and landslides induced by heavy rainfall represent an ubiquitous and destructive natural hazard in steep mountainous regions. For debris flows initiated by shallow landslides, the prediction of the resulting pathways and associated hazard is often hindered by uncertainty in determining initiation locations, volumes and mechanical state of the mobilized debris (and by model parameterization). We propose a framework for linking a simplified physically-based debris flow runout model with a novel Landslide Hydro-mechanical Triggering (LHT) model to obtain a coupled landslide-debris flow susceptibility and hazard assessment. We first compared the simplified debris flow model of Perla (1980) with a state-of-the art continuum-based model (RAMMS) and with an empirical model of Rickenmann (1999) at the catchment scale. The results indicate that predicted runout distances by the Perla model are in reasonable agreement with inventory measurements and with the other models. Predictions of localized shallow landslides by LHT model provides information on water content of released mass. To incorporate effects of water content and flow viscosity as provided by LHT on debris flow runout, we adapted the Perla model. The proposed integral link between landslide triggering susceptibility quantified by LHT and subsequent debris flow runout hazard calculation using the adapted Perla model provides a spatially and temporally resolved framework for real-time hazard assessment at the catchment scale or along critical infrastructure (roads, railroad lines).

Characterization of Hypervelocity Impact Debris from the DebriSat Tests

NASA Astrophysics Data System (ADS)

Adams, P. M.; Sheaffer, P. M.; Lingley, Z.; Radhakrishnan, G.

The DebriSat program consisted of 3 hypervelocity impact tests conducted in 2 Torr of air with 7 km/s, 600 g aluminum projectiles. In the first test, Pre Preshot, the target consisted of multiple layers of fiberglass, stainless steel and Kevlar fabric. No soft catch foam was used. The subsequent two tests, DebrisLV and DebriSat, were designed to simulate hypervelocity impacts with a launch vehicle upper stage and a modern LEO satellite, respectively. The interior of the chamber was lined with soft catch foam to trap break-up fragments. In all three tests, witness plates were placed near the target to sample impact debris and determine its reflectance, composition and spectral properties. Reflectance measurements are important for calculating the size of orbital hypervelocity impact fragments. The debris from the Pre Preshot test consisted of a two-phase mixture formed from solidified molten silicate and steel droplets. Individual droplets ranged from 100 μm to 10 nm. The reflectance of witness plates dropped from 95% to 20-30% as a result of the debris. Debris collected on witness plates in the DebrisLV and DebriSat tests consisted of μm to nm-sized solidified molten metallic droplets in a matrix of condensed vaporized soft catch. Disordered graphitic carbon was also detected. The reflectance of debris-covered witness plates dropped from 95% to 5%. The dramatic decrease in reflectance for hypervelocity impact debris is attributed to the effect of scattering from μm to nm sized solidified molten metallic droplets and the presence of graphitic carbon, when organics are present. The presence of soft catch in the later tests and the high organic content with graphitic carbon in the debris appear to be responsible for this much lower post-test reflectance. Understanding orbital debris reflectance is critical for estimating size and determining debris detectability.

An eddy covariance system to characterize the atmospheric surface layer and turbulent latent heat fluxes over a debris-covered Himalayan glacier.

NASA Astrophysics Data System (ADS)

Litt, Maxime; Steiner, Jakob F.; Stigter, Emmy E.; Immerzeel, Walter; Shea, Joseph Michael

2017-04-01

Over debris-covered glaciers, water content variations in the debris layer can drive significant changes in its thermal conductivity and significantly impact melt rates. Since sublimation and evaporation are favoured in high-altitude conditions, e.g., low atmospheric pressure and high wind speeds, they are expected to strongly influence the water balance of the debris-layer. Dedicated latent heat fluxes measurements at the debris surface are essential to characterize the debris heat conductivity in order to assess underlying ice melt. Furthermore, the contribution of the turbulent fluxes in the surface energy balance over debris covered glacier remains uncertain since they are generally evaluated through similarity methods which might not be valid in complex terrain. We present the first results of a 15-day eddy-covariance experiment installed at the end of the monsoon (September-October) on a 3-m tower above the debris-covered Lirung glacier in Nepal. The tower also included measurements of the 4 radiation components. The eddy covariance measurements allowed for the characterization of the turbulence in the atmospheric surface layer, as well as the direct measurements of evaporation, sublimation and turbulent sensible heat fluxes. The experiment helps us to evaluate the contribution of turbulent fluxes to the surface energy balance over this debris-covered glacier, through a precise characterization of the overlying turbulent atmospheric surface layer. It also helps to study the role of the debris-layer water content changes through evaporation and sublimation and its feedback on heat conduction in this layer. The large observed turbulent fluxes play a significant role in the energy balance at the debris surface and significantly influence debris moisture, conductivity and subsequently underlying ice melt.

Investigation of Bearing Fatigue Damage Life Prediction Using Oil Debris Monitoring

NASA Technical Reports Server (NTRS)

Dempsey, Paula J.; Bolander, Nathan; Haynes, Chris; Toms, Allison M.

2011-01-01

Research was performed to determine if a diagnostic tool for detecting fatigue damage of helicopter tapered roller bearings can be used to determine remaining useful life (RUL). The taper roller bearings under study were installed on the tail gearbox (TGB) output shaft of UH- 60M helicopters, removed from the helicopters and subsequently installed in a bearing spall propagation test rig. The diagnostic tool was developed and evaluated experimentally by collecting oil debris data during spall progression tests on four bearings. During each test, data from an on-line, in-line, inductance type oil debris sensor was monitored and recorded for the occurrence of pitting damage. Results from the four bearings tested indicate that measuring the debris generated when a bearing outer race begins to spall can be used to indicate bearing damage progression and remaining bearing life.

Exploring topographic methods for monitoring morphological changes in mountain channels of different size and slope

NASA Astrophysics Data System (ADS)

Theule, Joshua; Bertoldi, Gabriele; Comiti, Francesco; Macconi, Pierpaolo; Mazzorana, Bruno

2015-04-01

High resolution digital elevation models (DEM) can easily be obtained using either laser scanning technology or photogrammetry with structure from motion (SFM). The scale, resolution, and accuracy can vary according to how the data is acquired, such as by helicopter, drone, or extendable pole. In the Autonomous Province of Bozen-Bolzano (Northern Italy), we had the opportunity to compare several of these techniques at different scales in mountain streams ranging from low-gradient braided rivers to steep debris flow channels. The main objective is to develop protocols for efficient monitoring of morphologic changes in different parts of the river systems. For SFM methods, we used the software "Photoscan Professional" (Agisoft) to generate densified point clouds. Both artificial and natural targets were used to georeference them. In some cases, targets were not even necessary and point clouds could be aligned with older point clouds by using the iterative closest point algorithm in the freeware "CloudCompare". At the Mareit/Mareta River, a restored braided river, an airborne laser scan survey (2011) was compared to a SFM DEM derived from a helicopter photo survey (2014) carried out (by the Autonomous Province of Bolzano) at approximately 100 m above ground. Photogrammetry point clouds had an alignment error of 1.5 cm and had three times more data coverage than laser scanning. Indeed, the large spacing and clustering of 2011 ALS swaths led to areas of no data when a 10-cm grid is developed. In the Gadria basin, a debris flow monitoring catchment, we used a sediment retention basin to compare debris flow volumes resulting from i) a drone (by the "Mavtech" company) survey at 10 m above ground (with GoPro camera), ii) a 5-m pole-mounted camera (with Canon EOS 700D) and iii) a 3-m pole-mounted camera (with GoPro Hero Silver3+) to a iv) TLS survey. As the drone had limited load capacity (especially at high elevations) we used the lightweight GoPro Hero 3+, but due to the its low image quality and low survey elevations, more reference points were needed which became impractical. In contrast, the TLS survey was heavily influenced by the shadowing of the rough surfaces. Even though the pole-mounted camera is of lower technology, it has proven to be accurate (< 2cm RMSE) with better data coverage than the TLS due to the aerial perspective. Furthermore, the pole-mounted camera is the most field efficient due to the dependency of one person (little training required), little weather limitations, and a five times faster data acquisition than TLS surveys. A shorter pole with a GoPro camera allows faster and easier surveys but with the drawback of less precision and more noise. We easily obtained up to 6 DEMs of difference (DoD)within one year in active channel reaches and gullies in the Gadria catchment. This allowed to capture morphologic changes after important debris flow events, bedload transport, and bank erosion. DoDs also allowed us to monitor damages of structures due to erosional and depositional processes on alluvial fans. Our study highlights the importance of the bird's eye view which can be easily obtained by low cost SFM photogrammetry.

A debris avalanche at Forest Falls, San Bernardino County, California, July 11, 1999

USGS Publications Warehouse

Morton, Douglas M.; Hauser, Rachel M.

2001-01-01

This publication consists of the online version of a CD-ROM publication, U.S. Geological Survey Open-File Report 01-146. The data for this publication total 557 MB on the CD-ROM. For speed of transfer, the main PDF document has been compressed (with a subsequent loss of image quality) from 145 to 18.1 MB. The community of Forest Falls, California, is frequently subject to relatively slow moving debris flows. Some 11 debris flow events that were destructive to property have been recorded between 1955 and 1998. On July 11 and 13, 1999, debris flows again occurred, produced by high-intensity, short-duration monsoon rains. Unlike previous debris flow events, the July 11 rainfall generated a high-velocity debris avalanche in Snow Creek, one of the several creeks crossing the composite, debris flow dominated, alluvial fan on which Forest Falls is located. This debris avalanche overshot the bank of the active debris flow channel of Snow Creek, destroying property in the near vicinity and taking a life. The minimum velocity of this avalanche is calculated to have been in the range of 40 to 55 miles per hour. Impact from high-velocity boulders removed trees where the avalanche overshot the channel bank. Further down the fan, the rapidly moving debris fragmented the outer parts of the upslope side of large pine trees and embedded rock fragments into the tree trunks. Unlike the characteristic deposits formed by debris flows, the avalanche spread out down-slope and left no deposit suggestive of a debris avalanche. This summer monsoon-generated debris avalanche is apparently the first recorded for Forest Falls. The best indications of past debris avalanches may be the degree of permanent scars produced by extensive abrasion and splintering of the outer parts of pine trees that were in the path of an avalanche.

Experiments and simulation of a net closing mechanism for tether-net capture of space debris

NASA Astrophysics Data System (ADS)

Sharf, Inna; Thomsen, Benjamin; Botta, Eleonora M.; Misra, Arun K.

2017-10-01

This research addresses the design and testing of a debris containment system for use in a tether-net approach to space debris removal. The tether-net active debris removal involves the ejection of a net from a spacecraft by applying impulses to masses on the net, subsequent expansion of the net, the envelopment and capture of the debris target, and the de-orbiting of the debris via a tether to the chaser spacecraft. To ensure a debris removal mission's success, it is important that the debris be successfully captured and then, secured within the net. To this end, we present a concept for a net closing mechanism, which we believe will permit consistently successful debris capture via a simple and unobtrusive design. This net closing system functions by extending the main tether connecting the chaser spacecraft and the net vertex to the perimeter and around the perimeter of the net, allowing the tether to actuate closure of the net in a manner similar to a cinch cord. A particular embodiment of the design in a laboratory test-bed is described: the test-bed itself is comprised of a scaled-down tether-net, a supporting frame and a mock-up debris. Experiments conducted with the facility demonstrate the practicality of the net closing system. A model of the net closure concept has been integrated into the previously developed dynamics simulator of the chaser/tether-net/debris system. Simulations under tether tensioning conditions demonstrate the effectiveness of the closure concept for debris containment, in the gravity-free environment of space, for a realistic debris target. The on-ground experimental test-bed is also used to showcase its utility for validating the dynamics simulation of the net deployment, and a full-scale automated setup would make possible a range of validation studies of other aspects of a tether-net debris capture mission.

A deorbiter CubeSat for active orbital debris removal

NASA Astrophysics Data System (ADS)

Hakima, Houman; Bazzocchi, Michael C. F.; Emami, M. Reza

2018-05-01

This paper introduces a mission concept for active removal of orbital debris based on the utilization of the CubeSat form factor. The CubeSat is deployed from a carrier spacecraft, known as a mothership, and is equipped with orbital and attitude control actuators to attach to the target debris, stabilize its attitude, and subsequently move the debris to a lower orbit where atmospheric drag is high enough for the bodies to burn up. The mass and orbit altitude of debris objects that are within the realms of the CubeSat's propulsion capabilities are identified. The attitude control schemes for the detumbling and deorbiting phases of the mission are specified. The objective of the deorbiting maneuver is to decrease the semi-major axis of the debris orbit, at the fastest rate, from its initial value to a final value of about 6471 km (i.e., 100 km above Earth considering a circular orbit) via a continuous low-thrust orbital transfer. Two case studies are investigated to verify the performance of the deorbiter CubeSat during the detumbling and deorbiting phases of the mission. The baseline target debris used in the study are the decommissioned KOMPSAT-1 satellite and the Pegasus rocket body. The results show that the deorbiting times for the target debris are reduced significantly, from several decades to one or two years.

Coupling of rainfall-induced landslide triggering model with predictions of debris flow runout distances

NASA Astrophysics Data System (ADS)

Lehmann, Peter; von Ruette, Jonas; Fan, Linfeng; Or, Dani

2014-05-01

Rapid debris flows initiated by rainfall induced shallow landslides present a highly destructive natural hazard in steep terrain. The impact and run-out paths of debris flows depend on the volume, composition and initiation zone of released material and are requirements to make accurate debris flow predictions and hazard maps. For that purpose we couple the mechanistic 'Catchment-scale Hydro-mechanical Landslide Triggering (CHLT)' model to compute timing, location, and landslide volume with simple approaches to estimate debris flow runout distances. The runout models were tested using two landslide inventories obtained in the Swiss Alps following prolonged rainfall events. The predicted runout distances were in good agreement with observations, confirming the utility of such simple models for landscape scale estimates. In a next step debris flow paths were computed for landslides predicted with the CHLT model for a certain range of soil properties to explore its effect on runout distances. This combined approach offers a more complete spatial picture of shallow landslide and subsequent debris flow hazards. The additional information provided by CHLT model concerning location, shape, soil type and water content of the released mass may also be incorporated into more advanced models of runout to improve predictability and impact of such abruptly-released mass.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kalas, Paul G.; Rajan, Abhijith; Wang, Jason J.

Here, we present the first scattered light detections of the HD 106906 debris disk using the Gemini/Gemini Planet Imager in the infrared and Hubble Space Telescope (HST)/Advanced Camera for Surveys in the optical. HD 106906 is a 13 Myr old F5V star in the Sco–Cen association, with a previously detected planet-mass candidate HD 106906b projected 650 AU from the host star. Our observations reveal a near edge-on debris disk that has a central cleared region with radius ~50 AU, and an outer extent >500 AU. The HST data show that the outer regions are highly asymmetric, resembling the "needle" morphologymore » seen for the HD 15115 debris disk. The planet candidate is oriented ~21° away from the position angle of the primary's debris disk, strongly suggesting non-coplanarity with the system. We hypothesize that HD 106906b could be dynamically involved in the perturbation of the primary's disk, and investigate whether or not there is evidence for a circumplanetary dust disk or cloud that is either primordial or captured from the primary. In conclusion, we show that both the existing optical properties and near-infrared colors of HD 106906b are weakly consistent with this possibility, motivating future work to test for the observational signatures of dust surrounding the planet.« less

Electrical characteristics of simulated tornadoes

NASA Astrophysics Data System (ADS)

Zimmerman, M. I.; Farrell, W. M.; Barth, E. L.; Lewellen, D. C.; Lewellen, W. S.; Perlongo, N. J.; Jackson, T.

2012-12-01

It is well known that tornadoes and dust devils have the ability to accumulate significant, visible clouds of debris. Collisions between sand-like debris species produce different electric charges on different types of grains, which convect along different trajectories around the vortex. Thus, significant charge separations and electric currents are possible, which as the vortex fluctuates over time are thought to produce ULF radiation signatures that have been measured in the field. These electric and magnetic fields may contain valuable information about tornado structure and genesis, and may be critical in driving electrochemical processes within dust devils on Mars. In the present work, existing large eddy simulations of debris-laden tornadoes performed at West Virginia University are coupled with a new debris-charging and advection code developed at Goddard Space Flight Center to investigate the detailed (meter-resolution) fluid-dynamic origins of electromagnetic fields within terrestrial vortices. First results are presented, including simulations of the electric and magnetic fields that would be observed by a near-surface, instrument-laden probe during a direct encounter with a tornado. This research was supported by an appointment to the NASA Postdoctoral Program at the Goddard Space Flight Center, administered by Oak Ridge Associated Universities through a contract with NASA. The generous allocation of computing resources by Dr. Timothy J. Stubbs is gratefully acknowledged.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kalas, Paul G.; Wang, Jason J.; Duchene, Gaspard

We present the first scattered light detections of the HD 106906 debris disk using the Gemini/Gemini Planet Imager in the infrared and Hubble Space Telescope (HST)/Advanced Camera for Surveys in the optical. HD 106906 is a 13 Myr old F5V star in the Sco–Cen association, with a previously detected planet-mass candidate HD 106906b projected 650 AU from the host star. Our observations reveal a near edge-on debris disk that has a central cleared region with radius ∼50 AU, and an outer extent >500 AU. The HST data show that the outer regions are highly asymmetric, resembling the “needle” morphology seenmore » for the HD 15115 debris disk. The planet candidate is oriented ∼21° away from the position angle of the primary’s debris disk, strongly suggesting non-coplanarity with the system. We hypothesize that HD 106906b could be dynamically involved in the perturbation of the primary’s disk, and investigate whether or not there is evidence for a circumplanetary dust disk or cloud that is either primordial or captured from the primary. We show that both the existing optical properties and near-infrared colors of HD 106906b are weakly consistent with this possibility, motivating future work to test for the observational signatures of dust surrounding the planet.« less

Man-Made Debris In and From Lunar Orbit

NASA Technical Reports Server (NTRS)

Johnson, Nicholas L.; McKay, Gordon A. (Technical Monitor)

1999-01-01

During 1966-1976, as part of the first phase of lunar exploration, 29 manned and robotic missions placed more than 40 objects into lunar orbit. Whereas several vehicles later successfully landed on the Moon and/or returned to Earth, others were either abandoned in orbit or intentionally sent to their destruction on the lunar surface. The former now constitute a small population of lunar orbital debris; the latter, including four Lunar Orbiters and four Lunar Module ascent stages, have contributed to nearly 50 lunar sites of man's refuse. Other lunar satellites are known or suspected of having fallen from orbit. Unlike Earth satellite orbital decays and deorbits, lunar satellites impact the lunar surface unscathed by atmospheric burning or melting. Fragmentations of lunar satellites, which would produce clouds of numerous orbital debris, have not yet been detected. The return to lunar orbit in the 1990's by the Hagoromo, Hiten, Clementine, and Lunar Prospector spacecraft and plans for increased lunar exploration early in the 21st century, raise questions of how best to minimize and to dispose of lunar orbital debris. Some of the lessons learned from more than 40 years of Earth orbit exploitation can be applied to the lunar orbital environment. For the near-term, perhaps the most important of these is postmission passivation. Unique solutions, e.g., lunar equatorial dumps, may also prove attractive. However, as with Earth satellites, debris mitigation measures are most effectively adopted early in the concept and design phase, and prevention is less costly than remediation.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Faye, S. A.; Shaughnessy, D. A.

The objective of this project is to provide a comprehensive study on the production routes and chemical separation requirements for activation products, fission products, and actinides required for the creation of realistic post-detonation surrogate debris. Isotopes that have been prioritized by debris diagnosticians will be examined for their ability to be produced at existing irradiation sources, production rates, and availability of target materials, and chemical separation procedures required to rapidly remove the products from the bulk target matrix for subsequent addition into synthetic debris samples. The characteristics and implications of the irradiation facilities on the isotopes of interest will bemore » addressed in addition to a summary of the isotopes that are already regularly produced. This is a planning document only.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Springer, H K; Miller, W O; Levatin, J L

Satellite collision debris poses risks to existing space assets and future space missions. Predictive models of debris generated from these hypervelocity collisions are critical for developing accurate space situational awareness tools and effective mitigation strategies. Hypervelocity collisions involve complex phenomenon that spans several time- and length-scales. We have developed a satellite collision debris modeling approach consisting of a Lagrangian hydrocode enriched with smooth particle hydrodynamics (SPH), advanced material failure models, detailed satellite mesh models, and massively parallel computers. These computational studies enable us to investigate the influence of satellite center-of-mass (CM) overlap and orientation, relative velocity, and material composition onmore » the size, velocity, and material type distributions of collision debris. We have applied our debris modeling capability to the recent Iridium 33-Cosmos 2251 collision event. While the relative velocity was well understood in this event, the degree of satellite CM overlap and orientation was ill-defined. In our simulations, we varied the collision CM overlap and orientation of the satellites from nearly maximum overlap to partial overlap on the outermost extents of the satellites (i.e, solar panels and gravity boom). As expected, we found that with increased satellite overlap, the overall debris cloud mass and momentum (transfer) increases, the average debris size decreases, and the debris velocity increases. The largest predicted debris can also provide insight into which satellite components were further removed from the impact location. A significant fraction of the momentum transfer is imparted to the smallest debris (< 1-5mm, dependent on mesh resolution), especially in large CM overlap simulations. While the inclusion of the smallest debris is critical to enforcing mass and momentum conservation in hydrocode simulations, there seems to be relatively little interest in their disposition. Based on comparing our results to observations, it is unlikely that the Iridium 33-Cosmos 2251 collision event was a large mass-overlap collision. We also performed separate simulations studying the debris generated by the collision of 5 and 10 cm spherical projectiles on the Iridium 33 satellite at closing velocities of 5, 10, and 15 km/s. It is important to understand the vulnerability of satellites to small debris threats, given their pervasiveness in orbit. These studies can also be merged with probabilistic conjunction analysis to better understand the risk to space assets. In these computational studies, we found that momentum transfer, kinetic energy losses due to dissipative mechanisms (e.g., fracture), fragment number, and fragment velocity increases with increasing velocity for a fixed projectile size. For a fixed velocity, we found that the smaller projectile size more efficiently transfers momentum to the satellite. This latter point has an important implication: Eight (spaced) 5 cm debris objects can impart more momentum to the satellite, and likely cause more damage, than a single 10 cm debris object at the same velocity. Further studies are required to assess the satellite damage induced by 1-5 cm sized debris objects, as well as multiple debris objects, in this velocity range.« less

Two populations and models of gamma ray bursts

NASA Technical Reports Server (NTRS)

Katz, J. I.

1993-01-01

Gamma-ray burst statistics are best explained by a source population at cosmological distances, while spectroscopy and intensity histories of some individual bursts imply an origin on Galactic neutron stars. To resolve this inconsistency I suggest the presence of two populations, one at cosmological distances and the other Galactic. I build on ideas of Shemi and Piran (1990) and of Rees and Mesozaros (1992) involving the interaction of fireball debris with surrounding clouds to explain the observed intensity histories in bursts at cosmological distances. The distances to the Galactic population are undetermined because they are too few to affect the statistics of intensity and direction; I explain them as resulting from magnetic reconnection in neutron star magnetospheres. An appendix describes the late evolution of the debris as a relativistic blast wave.

Dust evolution from comets

NASA Technical Reports Server (NTRS)

Sekanina, Z.

1976-01-01

The studies of the evolution of cometary debris are reviewed. The subject is divided into three major sections: (1) the developments in the immediate vicinity of the cometary nucleus, which is the source of the dust; (2) the formation of the dust tail; and (3) the blending of the debris with the dust component of interplanetary matter. The importance of the physical theory of comets is emphasized for the understanding of the early phase of evolution. A physico-dynamical model designed to analyze the particle-emission mechanism from the distribution of light in the dust tail is described and the results are presented. Increased attention is paid to large particles because of their importance for the evolution of the zodiacal cloud. Finally, implications are discussed for the future in situ investigations of comets.

Dust evolution from comets

NASA Technical Reports Server (NTRS)

Sekanina, Z.

1977-01-01

The studies of the evolution of cometary debris are reviewed. The subject is divided into three major sections: (1) the developments in the immediate vicinity of the cometary nucleus, which is the source of the dust; (2) the formation of the dust tail; and (3) the blending of the debris with the dust component of interplanetary matter. The importance of the physical theory of comets is emphasized for the understanding of the early phase of the evolution of cometary dust. A physico-dynamical model designed to analyze the particle-emission mechanism from the distribution of light in the dust tails is described and the results are presented. Increased attention is paid to large particles because of their importance for the evolution of the zodiacal cloud. Finally, implications are discussed for the future in situ investigations of comets.

Impact of the 2008 Wenchuan earthquake in China on subsequent long-term debris flow activities in the epicentral area

NASA Astrophysics Data System (ADS)

Zhang, S.; Zhang, L. M.

2017-01-01

The 2008 Wenchuan earthquake triggered the largest number of landslides among the recent strong earthquake events around the world. The loose landslide materials were retained on steep terrains and deep gullies. In the period from 2008 to 2015, numerous debris flows occurred during rainstorms along the Provincial Road 303 (PR303) near the epicentre of the earthquake, causing serious damage to the reconstructed highway. Approximately 5.24 × 106 m3 of debris-flow sediment was deposited shortly after the earthquake. This paper evaluates the evolution of the debris flows that occurred after the Wenchuan earthquake, which helps understand long-term landscape evolution and cascading effects in regions impacted by mega earthquakes. With the aid of a GIS platform combined with field investigations, we continuously tracked movements of the loose deposit materials in all the debris flow gullies along an 18 km reach of PR303 and the characteristics of the regional debris flows during several storms in the past seven years. This paper presents five important aspects of the evolution of debris flows: (1) supply of debris flow materials; (2) triggering rainfall; (3) initiation mechanisms and types of debris flows; (4) runout characteristics; and (5) elevated riverbed due to the deposited materials from the debris flows. The hillslope soil deposits gradually evolved into channel deposits and the solid materials in the channels moved towards the ravine mouth. Accordingly, channelized debris flows became dominant gradually. Due to the decreasing source material volume and changes in debris flow characteristics, the triggering rainfall tends to increase from 30 mm h- 1 in 2008 to 64 mm h- 1 in 2013, and the runout distance tends to decrease over time. The runout materials blocked the river and elevated the riverbed by at least 30 m in parts of the study area. The changes in the post-seismic debris flow activity can be categorized into three stages, i.e., active, unstable, and recession.

Ground cloud related weather modification effects. [heavy lift launch vehicles

NASA Technical Reports Server (NTRS)

Lee, J.

1980-01-01

The principal concerns about inadvertent weather modification by the solar power satellite system rocket effluents are discussed, namely the possibility that the ground cloud might temporarily modify local weather and the cumulative effects of nearly 500 launches per year. These issues are discussed through the consideration of (1) the possible alteration of the microphysical processes of clouds in the general area due to rocket effluents and debris and cooling water entrained during the launch and (2) the direct dynamical and thermodynamical responses to the inputs of thermal energy and moisture from the rocket exhaust for given ambient meteorological conditions. The huge amount of thermal energy contained in the exhaust of the proposed launch vehicle would in some situations induce a saturated, wet convective cloud or enhance an existing convective activity. Nevertheless, the effects would be limited to the general area of the launch site. The observed long lasting high concentrations of cloud condensation nuclei produced during and after a rocket launch may appreciably affect the frequency of occurrence and persistence of fogs and haze. In view of the high mission frequency proposed for the vehicle launches, a potential exists for a cumulative effect.

Impact experiments into multiple-mesh targets: Concept development of a lightweight collisional bumper

NASA Technical Reports Server (NTRS)

Hoerz, Friedrich; Cintala, Mark J.; Bernhard, Ronald P.; Cardenas, Frank; Davidson, William; Haynes, Gerald; See, Thomas H.; Winkler, Jerry; Gray, Barry

1993-01-01

The utility of multiple-mesh targets as potential lightweight shields to protect spacecraft in low-Earth orbit against collisional damage is explored. Earlier studies revealed that single meshes comminute hypervelocity impactors with efficiencies comparable to contiguous targets. Multiple interaction of projectile fragments with any number of meshes should lead to increased comminution, deceleration, and dispersion of the projectile, such that all debris exiting the mesh stack possesses low specific energies (ergs/sq cm) that would readily be tolerated by many flight systems. The study is conceptually exploring the sensitivity of major variables such as impact velocity, the specific areal mass (g/sq cm) of the total mesh stack (SM), and the separation distance (S) between individual meshes. Most experiments employed five or ten meshes with total SM typically less than 0.5 the specific mass of the impactor, and silicate glass impactors rather than metal projectiles. While projectile comminution increases with increasing impact velocity due to progressively higher shock stresses, encounters with multiple-meshes at low velocity (1-2 km/s) already lead to significant disruption of the glass impactors, with the resulting fragments being additionally decelerated and dispersed by subsequent meshes, and, unlike most contiguous single-plate bumpers, leading to respectable performance at low velocity. Total specific bumper mass must be the subject of careful trade-off studies; relatively massive bumpers will generate too much debris being dislodged from the bumper itself, while exceptionally lightweight designs will not cause sufficient comminution, deceleration, or dispersion of the impactor. Separation distance was found to be a crucial design parameter, as it controls the dispersion of the fragment cloud. Substantial mass savings could result if maximum separation distances were employed. The total mass of debris dislodged by multiple-mesh stacks is modestly smaller than that of single, contiguous-membrane shields. The cumulative surface area of all penetration holes in multiple mesh stacks is an order of magnitude smaller than that in analog multiple-foil shields, suggesting good long-term performance of the mesh designs. Due to different experimental conditions, direct and quantitative comparison with other lightweight shields is not possible at present.

Generation of pyroclastic flows and surges by hot-rock avalanches from the dome of Mount St. Helens volcano, USA

USGS Publications Warehouse

Mellors, R.A.; Waitt, R.B.; Swanson, D.A.

1988-01-01

Several hot-rock avalanches have occurred during the growth of the composite dome of Mount St. Helens, Washington between 1980 and 1987. One of these occurred on 9 May 1986 and produced a fan-shaped avalanche deposit of juvenile dacite debris together with a more extensive pyroclastic-flow deposit. Laterally thinning deposits and abrasion and baking of wooden and plastic objects show that a hot ash-cloud surge swept beyond the limits of the pyroclastic flow. Plumes that rose 2-3 km above the dome and vitric ash that fell downwind of the volcano were also effects of this event, but no explosion occurred. All the facies observed originated from a single avalanche. Erosion and melting of craterfloor snow by the hot debris caused debris flows in the crater, and a small flood that carried juvenile and other clasts north of the crater. A second, broadly similar event occured in October 1986. Larger events of this nature could present a significant volcanic hazard. ?? 1988 Springer-Verlag.

Comparing two models for post-wildfire debris flow susceptibility mapping

NASA Astrophysics Data System (ADS)

Cramer, J.; Bursik, M. I.; Legorreta Paulin, G.

2017-12-01

Traditionally, probabilistic post-fire debris flow susceptibility mapping has been performed based on the typical method of failure for debris flows/landslides, where slip occurs along a basal shear zone as a result of rainfall infiltration. Recent studies have argued that post-fire debris flows are fundamentally different in their method of initiation, which is not infiltration-driven, but surface runoff-driven. We test these competing models by comparing the accuracy of the susceptibility maps produced by each initiation method. Debris flow susceptibility maps are generated according to each initiation method for a mountainous region of Southern California that recently experienced wildfire and subsequent debris flows. A multiple logistic regression (MLR), which uses the occurrence of past debris flows and the values of environmental parameters, was used to determine the probability of future debris flow occurrence. The independent variables used in the MLR are dependent on the initiation method; for example, depth to slip plane, and shear strength of soil are relevant to the infiltration initiation, but not surface runoff. A post-fire debris flow inventory serves as the standard to compare the two susceptibility maps, and was generated by LiDAR analysis and field based ground-truthing. The amount of overlap between the true locations where debris flow erosion can be documented, and where the MLR predicts high probability of debris flow initiation was statistically quantified. The Figure of Merit in Space (FMS) was used to compare the two models, and the results of the FMS comparison suggest that surface runoff-driven initiation better explains debris flow occurrence. Wildfire can breed conditions that induce debris flows in areas that normally would not be prone to them. Because of this, nearby communities at risk may not be equipped to protect themselves against debris flows. In California, there are just a few months between wildland fire season and the wet season to assess a community's risk and prepare. It is important, therefore, that researchers have a way to quickly and accurately assess the susceptibility for debris flows in recently burned areas.

Discrete Particle Method for Simulating Hypervelocity Impact Phenomena.

PubMed

Watson, Erkai; Steinhauser, Martin O

2017-04-02

In this paper, we introduce a computational model for the simulation of hypervelocity impact (HVI) phenomena which is based on the Discrete Element Method (DEM). Our paper constitutes the first application of DEM to the modeling and simulating of impact events for velocities beyond 5 kms -1 . We present here the results of a systematic numerical study on HVI of solids. For modeling the solids, we use discrete spherical particles that interact with each other via potentials. In our numerical investigations we are particularly interested in the dynamics of material fragmentation upon impact. We model a typical HVI experiment configuration where a sphere strikes a thin plate and investigate the properties of the resulting debris cloud. We provide a quantitative computational analysis of the resulting debris cloud caused by impact and a comprehensive parameter study by varying key parameters of our model. We compare our findings from the simulations with recent HVI experiments performed at our institute. Our findings are that the DEM method leads to very stable, energy-conserving simulations of HVI scenarios that map the experimental setup where a sphere strikes a thin plate at hypervelocity speed. Our chosen interaction model works particularly well in the velocity range where the local stresses caused by impact shock waves markedly exceed the ultimate material strength.

Dusty Disks, Diffuse Clouds, and Dim Suns: Galactic Science with the Infrared Spectrograph on the Spitzer Space Telescope

NASA Technical Reports Server (NTRS)

Roellig, T. L.; Watson, D. M.; Uchida, K. I.; Forrest, W. J.; VanCleve, J. E.; Herter, T. L.; Sloan, G. C.; Furlan, E.; Wilson, J. C.; Bernard-Salas, J.

2004-01-01

The Infrared Spectrograph (IRS) on the Spitzer Space Telescope has now been in routine science operations since Dec. 14,2003. The IRS Science Team has used a portion of their guaranteed time to pursue three major science themes in galactic astronomy: the evolution of protostellar disks and debris disks; the composition and evolution of diffuse matter and clouds in the interstellar medium; and the composition and structure of brown dwarfs and low-mass main-sequence stars. We report here on the results from the first five months of IRS observations in these programs. Full IRS Spectra have already been obtained for large samples of YSO/protoplanetary disks in the Taurus and TW Hya associations, and or debris disks around main-sequence stars, in which many aspects of the evolution of planetary systems can be addressed for the first time. As anticipated, the mid-infrared IRS observations of brown dwarfs have yielded important new information about their atmospheres, including the identification of NH3 and measurements of new methane features. This work is based on observations made with the Spitzer Space Telescope, which is operated by the Jet Propulsion Laboratory, California Institute of Technology under NASA contract 1407. Support for this work was provided by NASA's Office of Space Science.

Dusty Disks, Diffuse Clouds, and Dim Suns - Galactic Science with the Infrared Spectrograph on the Spitzer Space Telescope

NASA Astrophysics Data System (ADS)

Roellig, T. L.; Watson, D. M.; Uchida, K. I.; Forrest, W. J.; Van Cleve, J. E.; Herter, T. L.; Sloan, G. C.; Furlan, E.; Wilson, J. C.; Bernard-Salas, J.; Saumon, D.; Leggett, S.; Chen, C.; Kemper, F.; Hartmann, L.; Marley, M.; Cushing, M.; Mainzer, A. K.; Kirkpatrick, D.; Jura, M.; Houck, J. R.

2004-05-01

The Infrared Spectrograph (IRS) on the Spitzer Space Telescope has now been in routine science operations since Dec. 14, 2003. The IRS Science Team has used a portion of their guaranteed time to pursue three major science themes in galactic astronomy: the evolution of protostellar disks and debris disks; the composition and evolution of diffuse matter and clouds in the interstellar medium; and the composition and structure of brown dwarfs and low-mass main-sequence stars. We report here on the results from the first five months of IRS observations in these programs. Full IRS Spectra have already been obtained for large samples of YSO/protoplanetary disks in the Taurus and TW Hya associations, and of debris disks around main-sequence stars, in which many aspects of the evolution of planetary systems can be addressed for the first time. As anticipated, the mid-infrared IRS observations of brown dwarfs have yielded important new information about their atmospheres, including the identification of NH3 and measurements of new methane features. This work is based on observations made with the Spitzer Space Telescope, which is operated by the Jet Propulsion Laboratory, California Institute of Technology under NASA contract 1407. Support for this work was provided by NASA's Office of Space Science.

Discrete Particle Method for Simulating Hypervelocity Impact Phenomena

PubMed Central

Watson, Erkai; Steinhauser, Martin O.

2017-01-01

In this paper, we introduce a computational model for the simulation of hypervelocity impact (HVI) phenomena which is based on the Discrete Element Method (DEM). Our paper constitutes the first application of DEM to the modeling and simulating of impact events for velocities beyond 5 kms−1. We present here the results of a systematic numerical study on HVI of solids. For modeling the solids, we use discrete spherical particles that interact with each other via potentials. In our numerical investigations we are particularly interested in the dynamics of material fragmentation upon impact. We model a typical HVI experiment configuration where a sphere strikes a thin plate and investigate the properties of the resulting debris cloud. We provide a quantitative computational analysis of the resulting debris cloud caused by impact and a comprehensive parameter study by varying key parameters of our model. We compare our findings from the simulations with recent HVI experiments performed at our institute. Our findings are that the DEM method leads to very stable, energy–conserving simulations of HVI scenarios that map the experimental setup where a sphere strikes a thin plate at hypervelocity speed. Our chosen interaction model works particularly well in the velocity range where the local stresses caused by impact shock waves markedly exceed the ultimate material strength. PMID:28772739

Characterization of the Space Shuttle Ascent Debris using CFD Methods

NASA Technical Reports Server (NTRS)

Murman, Scott M.; Aftosmis, Michael J.; Rogers, Stuart E.

2005-01-01

After video analysis of space shuttle flight STS-107's ascent showed that an object shed from the bipod-ramp region impacted the left wing, a transport analysis was initiated to determine a credible flight path and impact velocity for the piece of debris. This debris transport analysis was performed both during orbit, and after the subsequent re-entry accident. The analysis provided an accurate prediction of the velocity a large piece of foam bipod ramp would have as it impacted the wing leading edge. This prediction was corroborated by video analysis and fully-coupled CFD/six degree of freedom (DOF) simulations. While the prediction of impact velocity was accurate enough to predict critical damage in this case, one of the recommendations of the Columbia Accident Investigation Board (CAIB) for return-to-flight (RTF) was to analyze the complete debris environment experienced by the shuttle stack on ascent. This includes categorizing all possible debris sources, their probable geometric and aerodynamic characteristics, and their potential for damage. This paper is chiefly concerned with predicting the aerodynamic characteristics of a variety of potential debris sources (insulating foam and cork, nose-cone ablator, ice, ...) for the shuttle ascent configuration using CFD methods. These aerodynamic characteristics are used in the debris transport analysis to predict flight path, impact velocity and angle, and provide statistical variation to perform risk analyses where appropriate. The debris aerodynamic characteristics are difficult to determine using traditional methods, such as static or dynamic test data, due to the scaling requirements of simulating a typical debris event. The use of CFD methods has been a critical element for building confidence in the accuracy of the debris transport code by bridging the gap between existing aerodynamic data and the dynamics of full-scale, in-flight events.

POST Earthquake Debris Management — AN Overview

NASA Astrophysics Data System (ADS)

Sarkar, Raju

Every year natural disasters, such as fires, floods, earthquakes, hurricanes, landslides, tsunami, and tornadoes, challenge various communities of the world. Earthquakes strike with varying degrees of severity and pose both short- and long-term challenges to public service providers. Earthquakes generate shock waves and displace the ground along fault lines. These seismic forces can bring down buildings and bridges in a localized area and damage buildings and other structures in a far wider area. Secondary damage from fires, explosions, and localized flooding from broken water pipes can increase the amount of debris. Earthquake debris includes building materials, personal property, and sediment from landslides. The management of this debris, as well as the waste generated during the reconstruction works, can place significant challenges on the national and local capacities. Debris removal is a major component of every post earthquake recovery operation. Much of the debris generated from earthquake is not hazardous. Soil, building material, and green waste, such as trees and shrubs, make up most of the volume of earthquake debris. These wastes not only create significant health problems and a very unpleasant living environment if not disposed of safely and appropriately, but also can subsequently impose economical burdens on the reconstruction phase. In practice, most of the debris may be either disposed of at landfill sites, reused as materials for construction or recycled into useful commodities Therefore, the debris clearance operation should focus on the geotechnical engineering approach as an important post earthquake issue to control the quality of the incoming flow of potential soil materials. In this paper, the importance of an emergency management perspective in this geotechnical approach that takes into account the different criteria related to the operation execution is proposed by highlighting the key issues concerning the handling of the construction and demolition debris following an earthquake.

POST Earthquake Debris Management - AN Overview

NASA Astrophysics Data System (ADS)

Sarkar, Raju

Every year natural disasters, such as fires, floods, earthquakes, hurricanes, landslides, tsunami, and tornadoes, challenge various communities of the world. Earthquakes strike with varying degrees of severity and pose both short- and long-term challenges to public service providers. Earthquakes generate shock waves and displace the ground along fault lines. These seismic forces can bring down buildings and bridges in a localized area and damage buildings and other structures in a far wider area. Secondary damage from fires, explosions, and localized flooding from broken water pipes can increase the amount of debris. Earthquake debris includes building materials, personal property, and sediment from landslides. The management of this debris, as well as the waste generated during the reconstruction works, can place significant challenges on the national and local capacities. Debris removal is a major component of every post earthquake recovery operation. Much of the debris generated from earthquake is not hazardous. Soil, building material, and green waste, such as trees and shrubs, make up most of the volume of earthquake debris. These wastes not only create significant health problems and a very unpleasant living environment if not disposed of safely and appropriately, but also can subsequently impose economical burdens on the reconstruction phase. In practice, most of the debris may be either disposed of at landfill sites, reused as materials for construction or recycled into useful commodities Therefore, the debris clearance operation should focus on the geotechnical engineering approach as an important post earthquake issue to control the quality of the incoming flow of potential soil materials. In this paper, the importance of an emergency management perspective in this geotechnical approach that takes into account the different criteria related to the operation execution is proposed by highlighting the key issues concerning the handling of the construction and demolition debris following an earthquake.

Satellite Collision Modeling with Physics-Based Hydrocodes: Debris Generation Predictions of the Iridium-Cosmos Collision Event and Other Impact Events

NASA Astrophysics Data System (ADS)

Springer, H.; Miller, W.; Levatin, J.; Pertica, A.; Olivier, S.

2010-09-01

Satellite collision debris poses risks to existing space assets and future space missions. Predictive models of debris generated from these hypervelocity collisions are critical for developing accurate space situational awareness tools and effective mitigation strategies. Hypervelocity collisions involve complex phenomenon that spans several time and length-scales. We have developed a satellite collision debris modeling approach consisting of a Lagrangian hydrocode enriched with smooth particle hydrodynamics (SPH), advanced material failure models, detailed satellite mesh models, and massively parallel computers. These computational studies enable us to investigate the influence of satellite center-of-mass (CM) overlap and orientation, relative velocity, and material composition on the size, velocity, and material type distributions of collision debris. We have applied our debris modeling capability to the recent Iridium 33-Cosmos 2251 collision event. While the relative velocity was well understood in this event, the degree of satellite CM overlap and orientation was ill-defined. In our simulations, we varied the collision CM overlap and orientation of the satellites from nearly maximum overlap to partial overlap on the outermost extents of the satellites (i.e, solar panels and gravity boom). As expected, we found that with increased satellite overlap, the overall debris cloud mass and momentum (transfer) increases, the average debris size decreases, and the debris velocity increases. The largest predicted debris can also provide insight into which satellite components were further removed from the impact location. A significant fraction of the momentum transfer is imparted to the smallest debris (< 1-5mm, dependent on mesh resolution), especially in large CM overlap simulations. While the inclusion of the smallest debris is critical to enforcing mass and momentum conservation in hydrocode simulations, there seems to be relatively little interest in their disposition. Based on comparing our results to observations, it is unlikely that the Iridium 33-Cosmos 2251 collision event was a large mass-overlap collision. We also performed separate simulations studying the debris generated by the collision of 5 and 10 cm spherical projectiles on the Iridium 33 satellite at closing velocities of 5, 10, and 15 km/s. It is important to understand the vulnerability of satellites to small debris threats, given their pervasiveness in orbit. These studies can also be merged with probabilistic conjunction analysis to better understand the risk to space assets. In these computational studies, we found that momentum transfer, kinetic energy losses due to dissipative mechanisms (e.g., fracture), fragment number, and fragment velocity increases with increasing velocity for a fixed projectile size. For a fixed velocity, we found that the smaller projectile size more efficiently transfers momentum to the satellite. This latter point has an important implication: Eight (spaced) 5 cm debris objects can impart more momentum to the satellite, and likely cause more damage, than a single 10 cm debris object at the same velocity. Further studies are required to assess the satellite damage induced by 1-5 cm sized debris objects, as well as multiple debris objects, in this velocity range.

Plant growth on debris covered glacier surfaces - ecology, vegetation patterns and implications for debris mantled glaciers serving as cold and warm stage plant refugia in the past

NASA Astrophysics Data System (ADS)

Fickert, Thomas; Friend, Donald; Grüninger, Friederike; Molnia, Bruce; Richter, Michael

2017-04-01

As stated at the International Conference on Debris-Covered Glaciers in 2000, "debris-covered glaciers comprise a significant fraction of the global population of glaciers...." Given a minimum of debris thickness and sufficient stability, these surfaces host surprisingly diverse plant assemblages, both floristically and structurally. Observations of plant growth on glacier surfaces are reported from around the world - including mature forests with trees more than 50cm in diameter. Debris covered glacier surfaces are mobile habitats for plants, which migrate downhill with glacier movement, but are able to spread upward with strong anabatic valley winds. Plant growth is possible even on a very shallow debris cover. Depending on site conditions, floristic composition and structure of vegetation on debris covered glaciers represent a mosaic of environments, including subnival pioneer communities, glacier foreland early- to late-successional stages, and morainal locations. The taxa involved display a wide spectrum of adaptations to habitat conditions with particular migration and dispersal strategies. With a shallow debris cover, alpine/subnival taxa can grow considerably below their usual altitudinal niche due to the cooler subsurface soil temperatures. In contrast, a greater thickness of debris cover allows even thermophilous plants of lower elevations to grow on glacier surfaces. Employing the principle of actualism, debris covered glaciers provided important and previously undocumented refugia for plants during the Pleistocene cold stages from which alpine and arctic plant species were able to re-establish and spread in post-glacial time. This assumption is complementary to the two competing ideas to explain the fate of alpine and/or arctic taxa during the Pleistocene, the nunatak hypothesis (i.e. in-situ survival of plants on unglaciated summits) and tabula rasa theory (i.e. displacement of plants and subsequent remigration). Vice versa debris covered glaciers might have served as refugia for cryophilic plants during Holocene warm stages.

Simulating the evolution of optically dark HI clouds in the Virgo cluster : will no-one rid me of this turbulent sphere ?

NASA Astrophysics Data System (ADS)

Taylor, R.; Wünsch, R.; Palouš, J.

2018-05-01

Most detected neutral atomic hydrogen (HI) at low redshift is associated with optically bright galaxies. However, a handful of HI clouds are known which appear to be optically dark and have no nearby potential progenitor galaxies, making tidal debris an unlikely explanation. In particular, 6 clouds identified by the Arecibo Galaxy Environment Survey are interesting due to the combination of their small size, isolation, and especially their broad line widths atypical of other such clouds. A recent suggestion is that these clouds exist in pressure equilibrium with the intracluster medium, with the line width arising from turbulent internal motions. Here we explore that possibility by using the FLASH code to perform a series of 3D hydro simulations. Our clouds are modelled using spherical Gaussian density profiles, embedded in a hot, low-density gas representing the intracluster medium. The simulations account for heating and cooling of the gas, and we vary the structure and strength of their internal motions. We create synthetic HI spectra, and find that none of our simulations reproduce the observed cloud parameters for longer than ˜100 Myr : the clouds either collapse, disperse, or experience rapid heating which would cause ionisation and render them undetectable to HI surveys. While the turbulent motions required to explain the high line widths generate structures which appear to be inherently unstable, making this an unlikely explanation for the observed clouds, these simulations demonstrate the importance of including the intracluster medium in any model seeking to explain the existence of these objects.

Contrasting rainfall generated debris flows from adjacent watersheds at Forest Falls, southern California, USA

USGS Publications Warehouse

Morton, D.M.; Alvarez, R.M.; Ruppert, K.R.; Goforth, B.

2008-01-01

Debris flows are widespread and common in many steeply sloping areas of southern California. The San Bernardino Mountains community of Forest Falls is probably subject to the most frequently documented debris flows in southern California. Debris flows at Forest Falls are generated during short-duration high-intensity rains that mobilize surface material. Except for debris flows on two consecutive days in November 1965, all the documented historic debris flows have occurred during high-intensity summer rainfall, locally referred to as 'monsoon' or 'cloudburst' rains. Velocities of the moving debris range from about 5??km/h to about 90??km/h. Velocity of a moving flow appears to be essentially a function of the water content of the flow. Low velocity debris flows are characterized by steep snouts that, when stopped, have only small amounts of water draining from the flow. In marked contrast are high-velocity debris flows whose deposits more resemble fluvial deposits. In the Forest Falls area two adjacent drainage basins, Snow Creek and Rattlesnake Creek, have considerably different histories of debris flows. Snow Creek basin, with an area about three times as large as Rattlesnake Creek basin, has a well developed debris flow channel with broad levees. Most of the debris flows in Snow Creek have greater water content and attain higher velocities than those of Rattlesnake Creek. Most debris flows are in relative equilibrium with the geometry of the channel morphology. Exceptionally high-velocity flows, however, overshoot the channel walls at particularly tight channel curves. After overshooting the channel, the flows degrade the adjacent levee surface and remove trees and structures in the immediate path, before spreading out with decreasing velocity. As the velocity decreases the clasts in the debris flows pulverize the up-slope side of the trees and often imbed clasts in them. Debris flows in Rattlesnake Creek are relatively slow moving and commonly stop in the channel. After the channel is blocked, subsequent debris flows cut a new channel upstream from the blockage that results in the deposition of new debris-flow deposits on the lower part of the fan. Shifting the location of debris flows on the Rattlesnake Creek fan tends to prevent trees from becoming mature. Dense growths of conifer seedlings sprout in the spring on the late summer debris flow deposits. This repeated process results in stands of even-aged trees whose age records the age of the debris flows. ?? 2007.

NASA's Optical Program on Ascension Island: Bringing MCAT to Life as the Eugene Stansbery-Meter Class Autonomous Telescope (ES-MCAT)

NASA Astrophysics Data System (ADS)

Lederer, S. M.; Hickson, P.; Cowardin, H. M.; Buckalew, B.; Frith, J.; Alliss, R.

In June 2015, the construction of the Meter Class Autonomous Telescope was completed and MCAT saw the light of the stars for the first time. In 2017, MCAT was newly dedicated as the Eugene Stansbery-MCAT telescope by NASA’s Orbital Debris Program Office (ODPO), in honour of his inspiration and dedication to this newest optical member of the NASA ODPO. Since that time, MCAT has viewed the skies with one engineering camera and two scientific cameras, and the ODPO optical team has begun the process of vetting the entire system. The full system vetting includes verification and validation of: (1) the hardware comprising the system (e.g. the telescopes and its instruments, the dome, weather systems, all-sky camera, FLIR cloud infrared camera, etc.), (2) the custom-written Observatory Control System (OCS) master software designed to autonomously control this complex system of instruments, each with its own control software, and (3) the custom written Orbital Debris Processing software for post-processing the data. ES-MCAT is now capable of autonomous observing to include Geosyncronous survey, TLE (Two-line element) tracking of individual catalogued debris at all orbital regimes (Low-Earth Orbit all the way to Geosynchronous (GEO) orbit), tracking at specified non-sidereal rates, as well as sidereal rates for proper calibration with standard stars. Ultimately, the data will be used for validation of NASA’s Orbital Debris Engineering Model, ORDEM, which aids in engineering designs of spacecraft that require knowledge of the orbital debris environment and long-term risks for collisions with Resident Space Objects (RSOs).

Satellite vulnerability to space debris - an improved 3D risk assessment methodology

NASA Astrophysics Data System (ADS)

Grassi, Lilith; Tiboldo, Francesca; Destefanis, Roberto; Donath, Thérèse; Winterboer, Arne; Evans, Leanne; Janovsky, Rolf; Kempf, Scott; Rudolph, Martin; Schäfer, Frank; Gelhaus, Johannes

2014-06-01

The work described in the present paper, performed as a part of the P2 project, presents an enhanced method to evaluate satellite vulnerability to micrometeoroids and orbital debris (MMOD), using the ESABASE2/Debris tool (developed under ESA contract). Starting from the estimation of induced failures on spacecraft (S/C) components and from the computation of lethal impacts (with an energy leading to the loss of the satellite), and considering the equipment redundancies and interactions between components, the debris-induced S/C functional impairment is assessed. The developed methodology, illustrated through its application to a case study satellite, includes the capability to estimate the number of failures on internal components, overcoming the limitations of current tools which do not allow propagating the debris cloud inside the S/C. The ballistic limit of internal equipment behind a sandwich panel structure is evaluated through the implementation of the Schäfer Ryan Lambert (SRL) Ballistic Limit Equation (BLE). The analysis conducted on the case study satellite shows the S/C vulnerability index to be in the range of about 4% over the complete mission, with a significant reduction with respect to the results typically obtained with the traditional analysis, which considers as a failure the structural penetration of the satellite structural panels. The methodology has then been applied to select design strategies (additional local shielding, relocation of components) to improve S/C protection with respect to MMOD. The results of the analyses conducted on the improved design show a reduction of the vulnerability index of about 18%.

NASA's Optical Program on Ascension Island: Bringing MCAT to Life as the Eugene Stansbery-Meter Class Autonomous Telescope (ES-MCAT)

NASA Technical Reports Server (NTRS)

Lederer, S. M.; Hickson, P.; Cowardin, H. M.; Buckalew, B.; Frith, J.; Alliss, R.

2017-01-01

In June 2015, the construction of the Meter Class Autonomous Telescope was completed and MCAT saw the light of the stars for the first time. In 2017, MCAT was newly dedicated as the Eugene Stansbery-MCAT telescope by NASA's Orbital Debris Program Office (ODPO), in honor of his inspiration and dedication to this newest optical member of the NASA ODPO. Since that time, MCAT has viewed the skies with one engineering camera and two scientific cameras, and the ODPO optical team has begun the process of vetting the entire system. The full system vetting includes verification and validation of: (1) the hardware comprising the system (e.g. the telescopes and its instruments, the dome, weather systems, all-sky camera, FLIR cloud infrared camera, etc.), (2) the custom-written Observatory Control System (OCS) master software designed to autonomously control this complex system of instruments, each with its own control software, and (3) the custom written Orbital Debris Processing software for post-processing the data. ES-MCAT is now capable of autonomous observing to include Geosynchronous survey, TLE (Two-line element) tracking of individual catalogued debris at all orbital regimes (Low-Earth Orbit all the way to Geosynchronous (GEO) orbit), tracking at specified non-sidereal rates, as well as sidereal rates for proper calibration with standard stars. Ultimately, the data will be used for validation of NASA's Orbital Debris Engineering Model, ORDEM, which aids in engineering designs of spacecraft that require knowledge of the orbital debris environment and long-term risks for collisions with Resident Space Objects (RSOs).

Analysis Of The 2009 July Impact Debris In Jupiter'S Atmosphere

NASA Astrophysics Data System (ADS)

Sanchez-Lavega, Agustin; Hueso, R.; Legarreta, J.; Pérez-Hoyos, S.; García-Melendo, E.; Gómez, J. M.; Rojas, J. F.; Orton, G. S.; Wesley, A.; IOPW International Outer Planet Watch Team

2009-09-01

We report the analysis of images obtained by the contributors to the International Outer Planet Watch (IOPW) of the debris left in the atmosphere of Jupiter by the object that impacted the planet between 18 and 19 July 2009. The discovery images by Anthony Wesley in July 19.625 and the first two days of its tracking, shows a dark debris spot (continuum wavelength) located at planetocentric latitude -55.1 deg and 304.5 deg System III longitude. The imaging survey indicates that the spot was not present in July 18.375, so the impact occurred during a window between both dates. The main spot had a size of about 4,500 km and to its Northwest a thin debris halo of similar size was initially observed. Methane band images at a wavelength of 890 nm shows the spot to be bright indicating that the debris aerosols are highly placed in the atmosphere relative to surrounding clouds. At the central latitude of the impact, the Jovian flow has nearly zero speed but anticyclonic vorticity bounded by jets at -51.5 deg (directed westward with velocity -10 m/s) and at -57.5 deg (directed eastward with velocity 25 m/s). The morphology in the continuum and the spot brightness in the methane band strongly suggest that the feature was caused by a cometary or asteroidal impact, similar in behaviour to the SL9 impacts of 1994. This work has been funded by Spanish MEC AYA2006-07735 with FEDER support and Grupos Gobierno Vasco IT-464-07. RH acknowledges a "Ramón y Cajal” contract from MEC.

The Properties and Fate of the Galactic Center G2 Cloud

NASA Astrophysics Data System (ADS)

Shcherbakov, Roman V.

2014-03-01

The object G2 was recently discovered descending into the gravitational potential of the supermassive black hole (BH) Sgr A*. We test the photoionized cloud scenario, determine the cloud properties, and estimate the emission during the pericenter passage. The incident radiation is computed starting from the individual stars at the locations of G2. The radiative transfer calculations are conducted with CLOUDY code and 2011 broadband and line luminosities are fitted. The spherically symmetric, tidally distorted, and magnetically arrested cloud shapes are tested with both the interstellar medium dust and 10 nm graphite dust. The best-fitting magnetically arrested model has the initial density n init = 1.8 × 105 cm-3, initial radius R init = 2.2 × 1015 cm = 17 mas, mass m cloud = 4 M Earth, and dust relative abundance A = 0.072. It provides a good fit to 2011 data, is consistent with the luminosities in 2004 and 2008, and reaches an agreement with the observed size. We revise down the predicted radio and X-ray bow shock luminosities to be below the quiescent level of Sgr A*, which readily leads to non-detection in agreement to observations. The magnetic energy dissipation in the cloud at the pericenter coupled with more powerful irradiation may lead to an infrared source with an apparent magnitude m_{L^{\\prime }}\\approx 13.0. No shock into the cloud and no X-rays are expected from cloud squeezing by the ambient gas pressure. Larger than previously estimated cloud mass m cloud = (4-20) M Earth may produce a higher accretion rate and a brighter state of Sgr A* as the debris descend onto the BH.

Biological Effects of Nuclear Explosions (BENE) Domain Guide

DTIC Science & Technology

2012-09-01

DATE (DD-MM-YYYY) 2. REPORT TYPE 3. DATES COVERED (From – To) Technical Report October 2004-April 2005 4. TITLE AND SUBTITLE 5a. CONTRACT NUMBER...greatly increased in the nearby region because increasing amounts of contaminated earth and debris are sucked up into the radioactive cloud. In the case...or a denial scenario involving radioisotopes will be non-uniform exposure with various doses and dose rates producing very large variations in

Habitability in Different Milky Way Stellar Environments: A Stellar Interaction Dynamical Approach

PubMed Central

Pichardo, Bárbara; Lake, George; Segura, Antígona

2013-01-01

Abstract Every Galactic environment is characterized by a stellar density and a velocity dispersion. With this information from literature, we simulated flyby encounters for several Galactic regions, numerically calculating stellar trajectories as well as orbits for particles in disks; our aim was to understand the effect of typical stellar flybys on planetary (debris) disks in the Milky Way Galaxy. For the solar neighborhood, we examined nearby stars with known distance, proper motions, and radial velocities. We found occurrence of a disturbing impact to the solar planetary disk within the next 8 Myr to be highly unlikely; perturbations to the Oort cloud seem unlikely as well. Current knowledge of the full phase space of stars in the solar neighborhood, however, is rather poor; thus we cannot rule out the existence of a star that is more likely to approach than those for which we have complete kinematic information. We studied the effect of stellar encounters on planetary orbits within the habitable zones of stars in more crowded stellar environments, such as stellar clusters. We found that in open clusters habitable zones are not readily disrupted; this is true if they evaporate in less than 108 yr. For older clusters the results may not be the same. We specifically studied the case of Messier 67, one of the oldest open clusters known, and show the effect of this environment on debris disks. We also considered the conditions in globular clusters, the Galactic nucleus, and the Galactic bulge-bar. We calculated the probability of whether Oort clouds exist in these Galactic environments. Key Words: Stellar interactions—Galactic habitable zone—Oort cloud. Astrobiology 13, 491–509. PMID:23659647

CO2 lidar observations of Mount Pinatubo debris: FIRE 2 and longer-term measurements

NASA Technical Reports Server (NTRS)

Levinson, David H.; Post, Madison J.; Grund, Christian J.

1993-01-01

The volcanic debris in the stratosphere from the June 1991 eruption of Mt. Pinatubo first appeared over the NOAA Wave Propagation Laboratory (WPL) field site near Boulder, Colorado (40.15 N, 105.23 W), in July of 1991. The presence of the Pinatubo cloud has allowed us to characterize both the tropospheric and stratospheric aerosol backscatter using the NOAA/WPL CO2 Doppler lidar. The lidar has measured vertical backscatter profiles at lambda = 10.59 mu m for over a decade. Analysis of this dense set of profiles reveals the effects of atmospheric and microphysical processes during the buildup and decay of Mt. Pinatubo's clouds. Further information on the NOAA lidar, specifically calibrations using a hard target, can be found in Post and Cupp (1990). We present results of those measurements for June 15, 1991, through December 31, 1992. During that period of longer-term measurements, WPL took part in FIRE II (First ISCCP (International Satellite Cloud Climatology Project) Regional Experiment II), from November 12 through December 8, 1991, measuring vertical backscatter profiles almost daily. One of the mechanisms for purging stratospheric aerosols is tropopause folding, which occurs in cold-core extratropical cyclones. Tropospheric mass loading occurs during folding events which can substantially increase the amount of ice nuclei in the upper troposphere, and may affect the formation of cirrus in that region. Spring and fall are prominent times for tropopause folding events because of the migration of the subtropical and polar jet streams during the transition seasons. Sassen has suggested that the volcanic aerosols from Pinatubo played a role in the formation of cirrus during FIRE II, particularly during a period of moist subtropical flow on December 5-6, 1991.

Microphysical processing of aerosol particles in orographic clouds

NASA Astrophysics Data System (ADS)

Pousse-Nottelmann, S.; Zubler, E. M.; Lohmann, U.

2015-01-01

An explicit and detailed treatment of cloud-borne particles allowing for the consideration of aerosol cycling in clouds has been implemented in the regional weather forecast and climate model COSMO. The effects of aerosol scavenging, cloud microphysical processing and regeneration upon cloud evaporation on the aerosol population and on subsequent cloud formation are investigated. For this, two-dimensional idealized simulations of moist flow over two bell-shaped mountains were carried out varying the treatment of aerosol scavenging and regeneration processes for a warm-phase and a mixed-phase orographic cloud. The results allowed to identify different aerosol cycling mechanisms. In the simulated non-precipitating warm-phase cloud, aerosol mass is incorporated into cloud droplets by activation scavenging and released back to the atmosphere upon cloud droplet evaporation. In the mixed-phase cloud, a first cycle comprises cloud droplet activation and evaporation via the Wegener-Bergeron-Findeisen process. A second cycle includes below-cloud scavenging by precipitating snow particles and snow sublimation and is connected to the first cycle via the riming process which transfers aerosol mass from cloud droplets to snow flakes. In the simulated mixed-phase cloud, only a negligible part of the total aerosol mass is incorporated into ice crystals. Sedimenting snow flakes reaching the surface remove aerosol mass from the atmosphere. The results show that aerosol processing and regeneration lead to a vertical redistribution of aerosol mass and number. However, the processes not only impact the total aerosol number and mass, but also the shape of the aerosol size distributions by enhancing the internally mixed/soluble accumulation mode and generating coarse mode particles. Concerning subsequent cloud formation at the second mountain, accounting for aerosol processing and regeneration increases the cloud droplet number concentration with possible implications for the ice crystal number concentration.

Quantifying sources of fine sediment supplied to post-fire debris flows using fallout radionuclide tracers

NASA Astrophysics Data System (ADS)

Smith, Hugh G.; Sheridan, Gary J.; Nyman, Petter; Child, David P.; Lane, Patrick N. J.; Hotchkis, Michael A. C.; Jacobsen, Geraldine E.

2012-02-01

Fine sediment supply has been identified as an important factor contributing to the initiation of runoff-generated debris flows after fire. However, despite the significance of fines for post-fire debris flow generation, no investigations have sought to quantify sources of this material in debris flow affected catchments. In this study, we employ fallout radionuclides ( 137Cs, 210Pb ex and 239,240Pu) as tracers to measure proportional contributions of fine sediment (< 10 μm) from hillslope surface and channel bank sources to levee and terminal fan deposits formed by post-fire debris flows in two forest catchments in southeastern Australia. While 137Cs and 210Pb ex have been widely used in sediment tracing studies, application of Pu as a tracer represents a recent development and was limited to only one catchment. The ranges in estimated proportional hillslope surface contributions of fine sediment to individual debris flow deposits in each catchment were 22-69% and 32-74%. The greater susceptibility of 210Pb ex to apparent reductions in the ash content of channel deposits relative to hillslope sources resulted in its exclusion from the final analysis. No systematic change in the proportional source contributions to debris flow deposits was observed with distance downstream from channel initiation points. Instead, spatial variability in source contributions was largely influenced by the pattern of debris flow surges forming the deposits. Linking the tracing analysis with interpretation of depositional evidence allowed reconstruction of temporal sequences in sediment source contributions to debris flow surges. Hillslope source inputs dominated most elevated channel deposits such as marginal levees that were formed under peak flow conditions. This indicated the importance of hillslope runoff and fine sediment supply for debris flow generation in both catchments. In contrast, material stored within channels that was deposited during subsequent surges was predominantly channel-derived. The results demonstrate that fallout radionuclide tracers may provide unique information on changing source contributions of fine sediment during debris flow events.

Quantifying sources of fine sediment supplied to post-fire debris flows using fallout radionuclide tracers

NASA Astrophysics Data System (ADS)

Smith, Hugh; Sheridan, Gary; Nyman, Petter; Child, David; Lane, Patrick; Hotchkis, Michael

2013-04-01

The supply of fine sediment and ash has been identified as an important factor contributing to the initiation of runoff-generated debris flows after fire. However, despite the significance of fines for post-fire debris flow generation, no investigations have sought to quantify sources of this material in debris flow affected catchments. In this study, we employ fallout radionuclides (Cs-137, excess Pb-210 and Pu-239,240) as tracers to measure proportional contributions of fine sediment (<10 μm) from hillslope surface and channel bank sources to levee and terminal fan deposits formed by post-fire debris flows in two forest catchments in southeastern Australia. While Cs-137 and excess Pb-210 have been widely used in sediment tracing studies, application of Pu as a tracer represents a recent development and was limited to only one catchment. The estimated range in hillslope surface contributions of fine sediment to individual debris flow deposits in each catchment was 22-69% and 32-74%, respectively. No systematic change in the source contributions to debris flow deposits was observed with distance downstream from channel initiation points. Instead, spatial variability in source contributions was largely influenced by the pattern of debris flow surges forming the deposits. Linking the sediment tracing with interpretation of depositional evidence allowed reconstruction of temporal sequences in sediment source contributions to debris flow surges. Hillslope source inputs dominated most elevated channel deposits such as marginal levees that were formed under peak flow conditions. This indicated the importance of hillslope runoff and sediment supply for debris flow generation in both catchments. In contrast, material stored within channels that was deposited during subsequent surges was predominantly channel-derived. The results demonstrate that fallout radionuclide tracers may provide unique information on the changing source contributions of fine sediment during debris flow events.

Uncovering glacier dynamics beneath a debris mantle

NASA Astrophysics Data System (ADS)

Lefeuvre, P.-M.; Ng, F. S. L.

2012-04-01

Debris-covered glaciers (DCGs) have an extensive sediment mantle whose low albedo influences their surface energy balance to cause a buffering effect that could enhance or reduce ablation rates depending on the sediment thickness. The last effect suggests that some DCGs may be less sensitive to climate change and survive for longer than debris-free (or 'clean') glaciers under sustained climatic warming. However, the origin of DCGs is debated and the precise impact of the debris mantle on their flow dynamics and surface geometry has not been quantified. Here we investigate these issues with a numerical model that encapsulates ice-flow physics and surface debris evolution and transport along a glacier flow-line, as well as couples these with glacier mass balance. We model the impact of surface debris on ablation rates by a mathematical function based on published empirical data (including Ostrem's curve). A key interest is potential positive feedback of ablation on debris thickening and lowering of surface albedo. Model simulations show that when DCGs evolve to attain steady-state profiles, they reach lower elevations than clean glaciers do for the same initial and climatic conditions. Their mass-balance profile at steady state displays an inversion near the snout (where the debris cover is thickest) that is not observed in the clean-glacier simulations. In these cases, where the mantle causes complete buffering to inhibit ablation, the DCG does not reach a steady-state profile, and the sediment thickness evolves to a steady value that depends sensitively on the glacier surface velocities. Variation in the assumed englacial debris concentration in our simulations also determines glacier behaviour. With low englacial debris concentration, the DCG retreats initially while its mass-balance gradient steepens, but the glacier re-advances if it subsequently builds up a thick enough debris cover to cause complete buffering. We identify possible ways and challenges of testing this model with field observations of DCGs, given the inherent difficulty that such glaciers may not be in steady state.

Debris flow susceptibility mapping using a qualitative heuristic method and Flow-R along the Yukon Alaska Highway Corridor, Canada

NASA Astrophysics Data System (ADS)

Blais-Stevens, A.; Behnia, P.

2016-02-01

This research activity aimed at reducing risk to infrastructure, such as a proposed pipeline route roughly parallel to the Yukon Alaska Highway Corridor (YAHC), by filling geoscience knowledge gaps in geohazards. Hence, the Geological Survey of Canada compiled an inventory of landslides including debris flow deposits, which were subsequently used to validate two different debris flow susceptibility models. A qualitative heuristic debris flow susceptibility model was produced for the northern region of the YAHC, from Kluane Lake to the Alaska border, by integrating data layers with assigned weights and class ratings. These were slope angle, slope aspect, surficial geology, plan curvature, and proximity to drainage system. Validation of the model was carried out by calculating a success rate curve which revealed a good correlation with the susceptibility model and the debris flow deposit inventory compiled from air photos, high-resolution satellite imagery, and field verification. In addition, the quantitative Flow-R method was tested in order to define the potential source and debris flow susceptibility for the southern region of Kluane Lake, an area where documented debris flow events have blocked the highway in the past (e.g. 1988). Trial and error calculations were required for this method because there was not detailed information on the debris flows for the YAHC to allow us to define threshold values for some parameters when calculating source areas, spreading, and runout distance. Nevertheless, correlation with known documented events helped define these parameters and produce a map that captures most of the known events and displays debris flow susceptibility in other, usually smaller, steep channels that had not been previously documented.

Debris flow susceptibility mapping using a qualitative heuristic method and Flow-R along the Yukon Alaska Highway Corridor, Canada

NASA Astrophysics Data System (ADS)

Blais-Stevens, A.; Behnia, P.

2015-05-01

This research activity aimed at reducing risk to infrastructure, such as a proposed pipeline route roughly parallel to the Yukon Alaska Highway Corridor (YAHC) by filling geoscience knowledge gaps in geohazards. Hence, the Geological Survey of Canada compiled an inventory of landslides including debris flow deposits, which were subsequently used to validate two different debris flow susceptibility models. A qualitative heuristic debris flow susceptibility model was produced for the northern region of the YAHC, from Kluane Lake to the Alaska border, by integrating data layers with assigned weights and class ratings. These were slope angle, slope aspect (derived from a 5 m × 5 m DEM), surficial geology, permafrost distribution, and proximity to drainage system. Validation of the model was carried out by calculating a success rate curve which revealed a good correlation with the susceptibility model and the debris flow deposit inventory compiled from air photos, high resolution satellite imagery, and field verification. In addition, the quantitative Flow-R method was tested in order to define the potential source and debris flow susceptibility for the southern region of Kluane Lake, an area where documented debris flow events have blocked the highway in the past (e.g., 1988). Trial and error calculations were required for this method because there was not detailed information on the debris flows for the YAHC to allow us to define threshold values for some parameters when calculating source areas, spreading, and runout distance. Nevertheless, correlation with known documented events helped define these parameters and produce a map that captures most of the known events and displays debris flow susceptibility in other, usually smaller, steep channels that had not been previously documented.

An adaptive process-based cloud infrastructure for space situational awareness applications

NASA Astrophysics Data System (ADS)

Liu, Bingwei; Chen, Yu; Shen, Dan; Chen, Genshe; Pham, Khanh; Blasch, Erik; Rubin, Bruce

2014-06-01

Space situational awareness (SSA) and defense space control capabilities are top priorities for groups that own or operate man-made spacecraft. Also, with the growing amount of space debris, there is an increase in demand for contextual understanding that necessitates the capability of collecting and processing a vast amount sensor data. Cloud computing, which features scalable and flexible storage and computing services, has been recognized as an ideal candidate that can meet the large data contextual challenges as needed by SSA. Cloud computing consists of physical service providers and middleware virtual machines together with infrastructure, platform, and software as service (IaaS, PaaS, SaaS) models. However, the typical Virtual Machine (VM) abstraction is on a per operating systems basis, which is at too low-level and limits the flexibility of a mission application architecture. In responding to this technical challenge, a novel adaptive process based cloud infrastructure for SSA applications is proposed in this paper. In addition, the details for the design rationale and a prototype is further examined. The SSA Cloud (SSAC) conceptual capability will potentially support space situation monitoring and tracking, object identification, and threat assessment. Lastly, the benefits of a more granular and flexible cloud computing resources allocation are illustrated for data processing and implementation considerations within a representative SSA system environment. We show that the container-based virtualization performs better than hypervisor-based virtualization technology in an SSA scenario.

Numerical modelling study of gully recharge and debris flows in Haida Gwaii, British Columbia

NASA Astrophysics Data System (ADS)

Martin, Yvonne; Johnson, Edward; Chaikina, Olga

2015-04-01

In high mountains, debris flows are a major process responsible for transferring sediment to more downstream fluvial reaches. This sediment transfer begins on mountain hillslopes where various mass wasting processes move sediment from hillslopes to uppermost reaches of the channel system (these reaches are herein referred to as gullies and only experience water flow during high intensity precipitation events). Sediment recharge into gullies, which has received minimal attention in the scientific literature, refers to the transfer of sediment and other debris from surrounding hillslopes into gullies (Jakob and Oden, 2005). Debris flow occurrence and debris flow volumes depend on some precipitation threshold as well as volumes of material contained in the particular gully. For example, if one debris flow has removed all of the accumulated material from the gully, then any subsequent debris flow will be smaller if enough time has not yet passed for notable sediment recharge. Herein, we utilize the numerical model of landscape development, LandMod (Martin, 1998; Dadson and Church, 2005; Martin, 2007), to explore connections between hillslope processes, gully recharge rates, and transfer of sediment to downstream channel reaches in the Haida Gwaii, British Columbia. Hillslope processes in the model include shallow landsliding, bedrock failures and weathering. The updated debris flow algorithm is based on extensive field data available for debris flows in Haida Gwaii (e.g., Rood, 1984; Oden, 1994; Jakob and Oden, 2005), as well as theoretical considerations based on debris flow studies. The most significant model extension is the calculation of gully recharge rates; for each gully, the total accumulated sediment in gullies at each time step is determined using a power-law relation for area-normalized recharge rate versus elapsed time since the last debris flow. Thus, when the stochastic driver for debris flow occurrence triggers an event, the amount of stored material is known and can be transferred and deposited along the channel system. Results show that the size distribution of debris flows and sediment transfers from gullies to downstream reaches are modified by the inclusion of a module that accounts for sediment recharge when compared to model runs that do not consider gully recharge.

Determining the Location, Number Density and Temporal Evolution of Streams of Hazardous Near-Earth Objects Using the Magnetic Signatures Produced in Destructive Collisions

NASA Astrophysics Data System (ADS)

Lai, H.; Russell, C. T.; Wei, H.; Delzanno, G. L.; Connors, M. G.

2014-12-01

Near-Earth objects (NEOs) of tens of meters in diameter are difficult to detect by optical methods from the Earth but they result in the most damage per year. Many of these bodies are produced in non-destructive collisions with larger well-characterized NEOs. After generation, the debris spreads forward and backward in a cocoon around the orbit of the parent body. Thereafter, scattering will occur due to gravitational perturbations when the debris stream passes near a planet even when the parent body has no such close approaches. Therefore "safe" NEOs which have no close encounters to the Earth for thousands of years may be accompanied by potentially hazardous co-orbiting debris. We have developed a technique to identify co-orbiting debris by detecting the magnetic signature produced when some of the debris suffers destructive collisions with meteoroids, which are numerous and can be as small as tens of centimeters in diameter. Clouds of nanoscale dust/gas particles released in such collisions can interact coherently with the solar wind electromagnetically. The resultant magnetic perturbations are readily identified when they pass spacecraft equipped with magnetometers. We can use such observations to obtain the spatial and size distribution as well as temporal variation of the debris streams. A test of this technique has been performed and debris streams both leading and trailing asteroid 138175 have been identified. There is a finite spread across the original orbit and most of the co-orbitals were tens of meters in diameter before the disruptive collisions. We estimate that there were tens of thousands of such co-orbiting objects, comprising only 1% of the original mass of the parent asteroid but greatly increasing the impact hazard. A loss of the co-orbitals since 1970s has been inferred from observations with a decay time consistent with that calculated from the existing collisional model [Grün et al., 1985]. Therefore disruptive collisions are the main loss mechanism of the co-orbiting debris associated with 138175. In summary, our technique helps us to identify which NEOs are accompanied by hazardous debris trails. Although our technique provides only the statistical properties, it indicates where high resolution optical surveys should be obtained in order to identify and track specific hazardous bodies.

Evidence for debris flow gully formation initiated by shallow subsurface water on Mars

USGS Publications Warehouse

Lanza, N.L.; Meyer, G.A.; Okubo, C.H.; Newsom, Horton E.; Wiens, R.C.

2010-01-01

The morphologies of some martian gullies appear similar to terrestrial features associated with debris flow initiation, erosion, and deposition. On Earth, debris flows are often triggered by shallow subsurface throughflow of liquid water in slope-mantling colluvium. This flow causes increased levels of pore pressure and thus decreased shear strength, which can lead to slide failure of slope materials and subsequent debris flow. The threshold for pore pressure-induced failure creates a distinct relationship between the contributing area supplying the subsurface flow and the slope gradient. To provide initial tests of a similar debris flow initiation hypothesis for martian gullies, measurements of the contributing areas and slope gradients were made at the channel heads of martian gullies seen in three HiRISE stereo pairs. These gullies exhibit morphologies suggestive of debris flows such as leveed channels and lobate debris fans, and have well-defined channel heads and limited evidence for multiple flows. Our results show an area-slope relationship for these martian gullies that is consistent with that observed for terrestrial gullies formed by debris flow, supporting the hypothesis that these gullies formed as the result of saturation of near-surface regolith by a liquid. This model favors a source of liquid that is broadly distributed within the source area and shallow; we suggest that such liquid could be generated by melting of broadly distributed icy materials such as snow or permafrost. This interpretation is strengthened by observations of polygonal and mantled terrain in the study areas, which are both suggestive of near-surface ice. ?? 2009 Elsevier Inc.

Climatological and meteorological conditions associated with rain-induced periglacial debris flows in the Cascade Range, USA

NASA Astrophysics Data System (ADS)

Parker, L.; Nolin, A. W.

2009-04-01

Title: Climatological and meteorological conditions associated with rain-induced periglacial debris flows in the Cascade Range, USA Authors: L. Parker, A.W. Nolin Affiliation: Department of Geosciences, Oregon State University, Corvallis, Oregon, USA In November of 2006 an intense rainstorm of tropical origin, known colloquially as "Pineapple Express," inundated the Pacific Northwest region of the United States, initiating numerous periglacial debris flows on several of the stratovolcanoes in the Cascade Range of Oregon and Washington. Rain-induced periglacial debris flows are the result of the over-saturation and subsequent collapse of steep moraine in formerly glaciated valleys. These debris flows rapidly aggrade channels, deposit thick sediments in their path, and severely damage infrastructure. Here we focus on Mount Hood, Oregon and Mount Rainier, Washington in the investigation of meteorological and climatological conditions surrounding rain-induced periglacial debris flow events and their variability over time. Both anecdotal and observational evidence suggest that the Pineapple Express storms are a likely triggering mechanism for these rain-induced debris flows on the stratovolcanoes. Dates for the debris flow events for each mountain were linked with corresponding Pineapple Express storm events. Preliminary analysis suggests that one or more particular climatological or meteorological conditions may be central to the initiation of debris flows, though these conditions may not always be present during Pineapple Express storms. Antecedent snowpack conditions are also hypothesized to play an important role in periglacial rain-induced debris flow initiation as the presence of snow cover on the moraines and glaciers is thought to reduce the likelihood of a debris flow. Radiosonde and precipitation data from Salem, Oregon (KSLE) and Quillayute, Washington (KUIL) data are used to determine if freezing levels and precipitation amounts have changed over time for all documented Pineapple Express events. Particular focus is placed on those events associated with debris flows. Additionally, Snowpack Telemetry (SNOTEL) data are used to examine the antecedent snowpack conditions for each debris flow event. These results will ultimately be coupled with research concerning the geomorphological mechanisms behind debris flows on stratovolcanoes in the Cascades, and may lead to improved understanding and future projections concerning the timing, frequency and intensity of rain-induced periglacial debris flow events.

Alteration of glacigenic landforms by gravitational mass movements, Ragnarbreen and Ebbabreen, Svalbard

NASA Astrophysics Data System (ADS)

Ewertowski, Marek; Pleskot, Krzysztof; Tomczyk, Aleksandra

2015-04-01

The extensive recession of Svalbard's glaciers exposed areas containing large amount of dead-ice covered by relatively thin - usually less than a couple of meters - veneer of debris. This landscape can be very dynamic, mainly due to the mass movement processes and dead-ice melting. Continuous redistribution of sediments causes several phases of debris transfer and relief inversion. Hence, the primary glacial deposits released from ice are subsequently transferred by mass movement processes, until they finally reach more stable position. Investigations of dynamics of the mass movement and the way in which they alter the property of glacigenic sediments are therefore cruicial for proper understanding of sedimentary records of previous glaciations. The main objectives of this study were to: (1) quantify short-term dynamic of mass wasting processes; (2) investigate the transformation of the sediment's characteristic by mass wasting processes; (3) asses the contribution of different process to the overall dynamic of proglacial landscape. We focused on the mass-wasting processes in the forelands of two glaciers, Ebbabreen and Ragnarbreen, located near the Petuniabukta at the northern end of the Billefjorden, Spitsbergen. Repetitive topographic scanning was combined with sedimentological analysis of: grain size, clast shape in macro and micro scale and thin sections. Debris falls, slides, rolls and flows were the most important processes leading to reworking of glacigenic sediments and altering their properties. Contribution of different processes to the overall dynamic of the landforms was related mainly to the local conditions. Four different morphological types of sites were identified: (1) near vertical ice-cliffs covered with debris, transformed mainly due to dead-ice backwasting and debris falls and slides, (2) steep debris slopes with exposed ice-cores dominated by debris slides, (3) gentle sediment-mantled slopes transformed due to debris flows, and (4) non-active debris-mantled areas transformed only by dead-ice downwasting. The amount of volume loss due to the active mass movement processes and dead-ice melting (including both backwasting and downwasting) was up to more than 1.8 m a-1. In comparison, the amount of volume loss due to the dead-ice downwasting only was significantly lower at a maximum of 0.3 m a-1. The spatial and temporal distribution of volume changes, however, was quite diverse and for the most part related to local geomorphic conditions (e.g. slope gradient, occurrence of streams, and meltwater channels). We proposed a simplified model of spatio-temporal switching between stable and active conditions within the forelands of the studied glaciers. Transformations of landforms were attributed to the period of deglaciation and debris cover development. Stage 1 - shortly after deglaciation when the debris cover is thin (thinner than the permafrost active layer's thickness) mass movement processes become fairly common. They are facilitated by the dead-ice melting and steepness of the slopes. This stage can be observed in many lateral moraines, which are characterised by steep slopes, abundance of active mass movement processes, and by consequence a high degree of transformation. Stage 2 - ongoing mass-wasting processes lead to the transfer of sediments from steep slopes to more stable positions. As the thickness of the sediments increases, the debris cover starts to protect the dead-ice from melting and also contribute to the decrease in slope gradient. Thus, the resulting landscape is relatively stable and in equilibrium with current climatic and topographic conditions. This stage characterises most parts of the frontal (end) moraine complex of the studied glaciers; thus, their transformation rates are either very low or close to zero. Stage 3 - some parts of this stable landscape can be subsequently transformed again into an unstable state, mainly due to the effect of external factors such as streams or meltwater channels. This can lead to the development of mass movement processes and further slope instability, which could facilitate subsequent generation of debris flows. Stages described above can occur in a sort of spatio-temporal cycle, and, depending on local and external factors, the changes between stabilization of landforms and activation of mass flows can be repeated several times for any given area until the dead-ice is completely melted.

Drainage evolution in the debris avalanche deposits near Mount Saint Helens, Washington

NASA Technical Reports Server (NTRS)

Beach, G. L.; Dzurisin, D.

1984-01-01

The 18 May 1980 eruption of Mount St. Helens was initiated by a massive rockslide-debris avalanche which completely transformed the upper 25 km of the North Fork Toutle River valley. The debris was generated by one of the largest gravitational mass movements ever recorded on Earth. Moving at an average velocity of 35 m/s, the debris avalanche buried approximately 60 sq km of terrain to an average depth of 45 m with unconsolidated, poorly sorted volcaniclastic material, all within a period of 10 minutes. Where exposed and unaltered by subsequent lahars and pyroclastic flows, the new terrain surface was characterized predominantly by hummocks, closed depressions, and the absence of an identifiable channel network. Following emplacement of the debris avalanche, a complex interrelationship of fluvial and mass wasting processes immediately began operating to return the impacted area to an equilibrium status through the removal of material (potential energy) and re-establishment of graded conditions. In an attempt to chronicle the morphologic evolution of this unique environmental setting, a systematic series of interpretative maps of several selected areas was produced. These maps, which document the rate and character of active geomorphic processes, are discussed.

Tidal Disruption of Strengthless Rubble Piles: A Dimensional Analysis

NASA Technical Reports Server (NTRS)

Hahn, Joseph M.; Rettig, Terrence W.

1998-01-01

A relatively simple prescription for estimating the number of debris clumps (n) that form after a catastrophic tidal disruption event is presented. Following the breakup event, it is assumed that the individual debris particles follow keplerian orbits about the planet until the debris' gravitational contraction timescale (t(sub c)) becomes shorter than its orbital spreading timescale (t(sub s)). When the two timescales become comparable, self-gravity breaks up the debris train into n = L/D clumps, which is the debris length/diameter ratio at that instant. The clumps subsequently orbit the planet independent of each other. The predicted number of clumps n is in good agreement with more sophisticated N-body treatments of tidal breakup for parabolic encounters, and the dependence of n upon the progenitor's density as well as its orbit is also mapped out for hyperbolic encounters. These findings may be used to further constrain both the orbits and densities of the tidally disrupted bodies that struck Callisto and Ganymede. A cursory analysis shows that the Gomul and Gipul crater chains on Callisto, which have the greatest number of craters among the known chains, were formed by projectiles having comet-like densities estimated at rho(sub o) < 1 gm/cc.

AFRRI Reports First Quarter, January-March 1991

DTIC Science & Technology

1991-01-01

MIDDLEMAN. M. LUNA. and G. P. Bot tN. i Klebsiella bacteremia in cancer patients. .Am hJ ’d St1 165, 473- The effectiveness ofquinolones in the therapy of K...of the organism’s growth within the gut lumen, while pre- apy in the febrile neutropenic cancer patient: Clinical etficac\\ and serving the anaerobic...inhala- short-term beta /gamma radiation re- collapsed debris. tion. These patients were diagnosed leased in the emission cloud; external The triage officer

Characterization of the 2012-044C Briz-M Upper Stage Breakup

NASA Technical Reports Server (NTRS)

Hamilton, Joseph A.; Matney, Mark

2013-01-01

The NASA breakup model prediction was close to the observed population for catalog objects. The NASA breakup model predicted a larger population than was observed for objects under 10 cm. The stare technique produces low observation counts, but is readily comparable to model predictions. Customized stare parameters (Az, El, Range) were effective to increase the opportunities for HAX to observe the debris cloud. Other techniques to increase observation count will be considered for future breakup events.

Volcanic hazards and aviation safety

USGS Publications Warehouse

Casadevall, Thomas J.; Thompson, Theodore B.; Ewert, John W.; ,

1996-01-01

An aeronautical chart was developed to determine the relative proximity of volcanoes or ash clouds to the airports and flight corridors that may be affected by volcanic debris. The map aims to inform and increase awareness about the close spatial relationship between volcanoes and aviation operations. It shows the locations of the active volcanoes together with selected aeronautical navigation aids and great-circle routes. The map mitigates the threat that volcanic hazards pose to aircraft and improves aviation safety.

Hubble Captures Celestial Fireworks Within the Large Magellanic Cloud

NASA Technical Reports Server (NTRS)

2000-01-01

This is a color Hubble Space Telescope (HST) heritage image of supernova remnant N49, a neighboring galaxy, that was taken with Hubble's Wide Field Planetary Camera 2. Color filters were used to sample light emitted by sulfur, oxygen, and hydrogen. The color image was superimposed on a black and white image of stars in the same field also taken with Hubble. Resembling a fireworks display, these delicate filaments are actually sheets of debris from a stellar explosion.

ARC-1985-AC85-0199-5

NASA Image and Video Library

1985-03-02

Artist: Gebing Artist's conception of a newborne star, still hidden in visible light by the dust clouds within which it formed, shows matter in orbit around the rotating star. Such leftover debris may eventually form comets, planets, satellites, and asteroids. Material squeezed out by the formation process is thought to be ejected along the star's rotation axis in relatively narrow, high-velocity streams of matter. (ref: SIRTF borchure 'A Window on Cosmic Birth 1987) -- Milky Way with Black hole

Fine structure of striations observed in barium plasma injections in the magnetospheric cleft

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simons, D.J.; Eastman, T.E.; Pongratz, M.B.

1976-01-01

In January and November of 1975, the Los Alamos Scientific Laboratory sponsored four high altitude shaped charge barium plasma injections in the magnetospheric cleft region. These experiments were TORDO UNO (January 6), TORDO DOS (January 11), PERIQUITO UNO (November 25), and PERIQUITO DOS (November 28). All four injections took place near 500 km altitude, and optical data were taken from two aircraft and a ground station. The TORDO DOS and the PERIQUITO experiments showed rapid formation of striations (within one minute after injection), and fast horizontal spreading in contrast with TORDO UNO. In PERIQUITO DOS, the debris cloud spread magneticallymore » east-west with a small net northerly motion. TORDO UNO shows very rapid poleward motion, and the remaining two events resulted in magnetically east-west horizontal spreading, with no noticeable poleward motion. Striations observed in the PERIQUITO DOS experiment separate in opposite directions with relative velocities of up to 3 km/sec. These field-aligned structures appear to form in sheets of approximately constant magnetic latitude. Significant spatial variations occur on a scale of less than 200 meters. Spatial frequency power spectra across these striations have been determined at various times. Observations of the debris cloud and the fast barium streak show strong field-aligned coherency of striation fine structure, indicating a field line mapping of transverse electric fields and gradients.« less

Potential postwildfire debris-flow hazards—A prewildfire evaluation for the Jemez Mountains, north-central New Mexico

USGS Publications Warehouse

Tillery, Anne C.; Haas, Jessica R.

2016-08-11

Wildfire can substantially increase the probability of debris flows, a potentially hazardous and destructive form of mass wasting, in landscapes that have otherwise been stable throughout recent history. Although the exact location, extent, and severity of wildfire or subsequent rainfall intensity and duration cannot be known, probabilities of fire and debris‑flow occurrence for given locations can be estimated with geospatial analysis and modeling. The purpose of this report is to provide information on which watersheds might constitute the most serious potential debris-flow hazards in the event of a large-scale wildfire and subsequent rainfall in the Jemez Mountains. Potential probabilities and estimated volumes of postwildfire debris flows in both the unburned and previously burned areas of the Jemez Mountains and surrounding areas were estimated using empirical debris-flow models developed by the U.S. Geological Survey in combination with fire behavior and burn probability models developed by the U.S. Forest Service.Of the 4,998 subbasins modeled for this study, computed debris-flow probabilities in 671 subbasins were greater than 80 percent in response to the 100-year recurrence interval, 30-minute duration rainfall event. These subbasins ranged in size from 0.01 to 6.57 square kilometers (km2), with an average area of 0.29 km2, and were mostly steep, upstream tributaries to larger channels in the area. Modeled debris-flow volumes in 465 subbasins were greater than 10,000 cubic meters (m3), and 14 of those subbasins had modeled debris‑flow volumes greater than 100,000 m3.The rankings of integrated relative debris-flow hazard indexes for each subbasin were generated by multiplying the individual subbasin values for debris-flow volume, debris‑flow probability, and average burn probability. The subbasins with integrated hazard index values in the top 2 percent typically are large, upland tributaries to canyons and channels primarily in the Upper Rio Grande and Rio Grande-Santa Fe watershed areas. No subbasins in this group have basin areas less than 1.0 km2. Many of these areas already had significant mass‑wasting episodes following the Las Conchas Fire in 2011. Other subbasins with integrated hazard index values in the top 2 percent are scattered throughout the Jemez River watershed area, including some subbasins in the interior of the Valles Caldera. Only a few subbasins in the top integrated hazard index group are in the Rio Chama watershed area.This prewildfire assessment approach is valuable to resource managers because the analysis of the debris-flow threat is made before a wildfire occurs, which facilitates prewildfire management, planning, and mitigation. In north‑central New Mexico, widespread watershed restoration efforts are being done to safeguard vital watersheds against the threat of catastrophic wildfire. This study was designed to help select ideal locations for the restoration efforts that could have the best return on investment.

Nanodust released in interplanetary collisions

NASA Astrophysics Data System (ADS)

Lai, H. R.; Russell, C. T.

2018-07-01

The lifecycle of near-Earth objects (NEOs) involves a collisional cascade that produces ever smaller debris ending with nanoscale particles which are removed from the solar system by radiation pressure and electromagnetic effects. It has been proposed that the nanodust clouds released in collisions perturb the background interplanetary magnetic field and create the interplanetary field enhancements (IFEs). Assuming that this IFE formation scenario is actually operating, we calculate the interplanetary collision rate, estimate the total debris mass carried by nanodust, and compare the collision rate with the IFE rate. We find that to release the same amount of nanodust, the collision rate is comparable to the observed IFE rate. Besides quantitatively testing the association between the collisions evolving large objects and giant solar wind structures, such a study can be extended to ranges of smaller scales and to investigate the source of moderate and small solar wind perturbations.

Mass extinction caused by large bolide impacts

NASA Technical Reports Server (NTRS)

Alvarez, Luis W.

1987-01-01

A history and development status assessment is presented for the hypothesis that the great extinction of living species 65 million years ago, at the boundary between the Tertiary and Cretaceous geological ages, was due to the collision of a meteoroid, asteroid, or comet with the earth. The initial, deeply suggestive indication of the extraterrestial origin of the extinction-initiating mechanism was the detection of an exceptionally high concentration of iridium at the stratigraphic position of the extinction. Detailed computer modeling of the atmospheric effect of such a bolide impact has shown that the earth would have first grown intensely cold during a period of darkness due to particulate debris clouds in the upper atmosphere, followed by an enormous increase in global temperatures as the debris cleared, created by the persistence of greenhouse-effect gases; this heating would have been especially lethal to numerous forms of life.

Tungsten solution kinetics and amorphization of nickel in mechanically alloyed Ni-W alloys

NASA Technical Reports Server (NTRS)

Aning, A. O.; Wang, Z.; Courtney, T. H.

1993-01-01

The kinetics of solution of W, and the subsequent amorphization of Ni, in mechanically alloyed Ni-W alloys has been investigated. As W is a highly abrasive material in the energy intensive devices used for mechanical alloying, we studied the above reactions in different mills. One used hardened steel balls as the grinding media, and the other Al2O3. Abrasion is common to both mills, but Fe wear debris from the hardened steel enters into solution in the Ni rich phases whereas Al2O3 debris is present as small dispersoids. The kinetics of W solution and those of subsequent amorphization do not appear strongly affected by the Fe in solution or the Al2O3 dispersoid. Tungsten dissolves in crystalline Ni in amounts in excess of the equilibrium solubility during alloying. Amorphization of the Ni phase occurs if the W content in this phase exceeds ca. 28 at. pct.

Laboratory study of collisionless coupling between explosive debris plasma and magnetized ambient plasma

NASA Astrophysics Data System (ADS)

Bondarenko, A. S.; Schaeffer, D. B.; Everson, E. T.; Clark, S. E.; Lee, B. R.; Constantin, C. G.; Vincena, S.; Van Compernolle, B.; Tripathi, S. K. P.; Winske, D.; Niemann, C.

2017-08-01

The explosive expansion of a localized plasma cloud into a relatively tenuous, magnetized, ambient plasma characterizes a variety of astrophysical and space phenomena. In these rarified environments, collisionless electromagnetic processes rather than Coulomb collisions typically mediate the transfer of momentum and energy from the expanding "debris" plasma to the surrounding ambient plasma. In an effort to better understand the detailed physics of collisionless coupling mechanisms, compliment in situ measurements of space phenomena, and provide validation of previous computational and theoretical work, the present research jointly utilizes the Large Plasma Device and the Raptor laser facility at the University of California, Los Angeles to study the super-Alfvénic, quasi-perpendicular expansion of laser-produced carbon (C) and hydrogen (H) debris plasma through preformed, magnetized helium (He) ambient plasma via a variety of diagnostics, including emission spectroscopy, wavelength-filtered imaging, and a magnetic flux probe. Doppler shifts detected in a He1+ ion spectral line indicate that the ambient ions initially accelerate transverse to both the debris plasma flow and the background magnetic field. A qualitative analysis in the framework of a "hybrid" plasma model (kinetic ions and inertia-less fluid electrons) demonstrates that the ambient ion trajectories are consistent with the large-scale laminar electric field expected to develop due to the expanding debris. In particular, the transverse ambient ion motion provides direct evidence of Larmor coupling, a collisionless momentum exchange mechanism that has received extensive theoretical and numerical investigation. In order to quantitatively evaluate the observed Doppler shifts, a custom simulation utilizing a detailed model of the laser-produced debris plasma evolution calculates the laminar electric field and computes the initial response of a distribution of ambient test ions. A synthetic Doppler-shifted spectrum constructed from the simulated test ion velocities excellently reproduces the experimental measurements, verifying that the observed ambient ion motion corresponds to collisionless coupling through the laminar electric field.

Re-impacting Debris Facilitated Cooling of the Lunar Magma Ocean

NASA Astrophysics Data System (ADS)

Perera, Viranga; Jackson, Alan; Elkins-Tanton, Linda T.; Asphaug, Erik

2017-10-01

It is widely believed that the Moon formed from the debris of a giant impact between the proto-Earth and a roughly Mars-sized body. Concomitant to this formation scenario, and also inferred from geochemical analyses of Apollo samples, is the past existence of a Lunar Magma Ocean (LMO). After about 80% of the LMO solidified, it is believed that the mineral plagioclase would have become stable and crystallized out of the LMO. Rocks that formed principally of plagioclase would have been buoyant in the residual liquid and thus helped form a floatation crust that acted as a thermally conductive blanket over the LMO. Previous modelling work found that the LMO would have solidified in about 10 Myr. However, studies have shown that, during the giant impact event, a large quantity of debris (totaling over a Lunar mass) would have been released that was not immediately incorporated into the Earth and the Moon. This material would have subsequently re-impacted the Earth and the Moon. Particularly for the Moon, this debris would have punctured holes into the nascent lunar crust, attenuated its thermal blanketing effect, and thus facilitated the cooling of the LMO. We improve upon previous studies of the solidification of the LMO by incorporating this re-impacting debris, and find that the re-impacting debris may have reduced the LMO solidification time.

"Electrostructural Phase Changes" In Charged Particulate Clouds: Planetary and Astrophysical Implications

NASA Technical Reports Server (NTRS)

Marshall, J. R.

1999-01-01

There is empirical evidence that freely-suspended triboelectrostatically charged particulate clouds of dielectric materials undergo rapid conversion from (nominally) monodispersed "aerosols" to a system of well-defined grain aggregates after grain motion or fluid turbulence ceases within the cloud. In United States Microgravity Laboratory Space Shuttle experiments USML-1 and USML-2, it was found that ballistically-energized grain dispersions would rapidly convert into populations of filamentary aggregates after natural fluid (air) damping of grain motion. Unless continuously disrupted mechanically, it was impossible to maintain a non-aggregated state for the grain clouds of sand-size materials. Similarly, ground- based experiments with very fine dust-size material produced the same results: rapid, impulsive "collapse" of the dispersed grains into well-defined filamentary structures. In both ground-based and microgravity experiments, the chains or filaments were created by long-range dipole electrostatic forces and dipole-induced dielectric interactions, not by monopole interactions. Maintenance of the structures was assisted by short-range static boundary adhesion forces and van der Waals interactions. When the aggregate containers in the USML experiments were disturbed after aggregate formation, the quiescently disposed filaments would rearrange themselves into fractal bundles and tighter clusters as a result of enforced encounters with one another. The long-range dipole interactions that bring the grains together into aggregates are a product of randomly-distributed monopole charges on the grain surfaces. In computer simulations, it has been shown that when the force vectors of all the random charges (of both sign) on a grain are resolved mathematically by assuming Coulombic interaction between them, the net result is a dipole moment on individual grains, even though the grains are electrically neutral insofar as there is no predominance, on their surface, of one charge sign over another. The random charges of both sign derive from natural grain-to-grain interactions that produce triboelectrification via charge exchange every time grain surfaces make contact with one another. The conversion from a random distribution of grains (upon which there are randomly distributed charges) into an organization of electrostatically-ordered aggregates, can be regarded (within the framework of granular-material science) as an "electrical or Coulombic phase change" of the particulate cloud. It is not totally dissimilar from the more normal phase-change concept in which, for example, a gas with long free-path-molecules suddenly becomes a solid as a result of structural ordering of the molecules (notably, also the result of electronic forces, albeit at a different scale). In both the gas-to-solid case, and the aerosol-to-aggregate case, the same materials and charges are present before and after the phase change, but their arrangement now has a higher degree of order and a lower-energy configuration. An input of energy into the system is required to reverse the situation. The aggregates in the USML experiments were observed to undergo at least two phase changes as noted above. The point about phase changes, and by implication, the "electrostructural" reorganizations in particulate clouds, is the following: (a) they can occur very rapidly, almost spontaneously, above a critical cloud density, (b) in going from a higher energy state to a lower energy state, they convert to a denser system, (c) energy must be required to reverse the situation, implying that energy is released during the high-to-low energy phase change. In applying this information to natural particulate clouds, some inferences can be made (it is stressed that reference is still to dielectric materials attracted by dipole forces). There are several natural settings to which the USML observations apply, and to which the phase-change implications likewise apply. Dense clouds of triboelectrically-charged, kinetically-energized grains are to be found in volcanic eruptions (particularly on earth), aeolian dust storms (particularly on Mars), meteorite impact ejecta curtains (on all planets), in "immature" debris rings around planets (e.g., that from which our own Moon may have condensed), and in gravitationally collapsing protoplanetary dust/planetesimal debris disks where dielectric granules are being increasingly brought into collisional relationships with one another (increasing both charge exchange and physical proximity). It is noted that in many of these cases, the degree of electrical charging on the grains is likely to be much higher than that in the USML experiments where charging was not enhanced above the "normal", naturally encountered level for the particular materials (quartz, glass, and various silicate minerals). Application of the phase-change concept suggests that volcanic, aeolian, and impact debris clouds may, under certain circumstances, undergo rapid, impulsive, or even catastrophic collapse into a denser state that will lead to rapid precipitation or fall-out of suspended particulates. Although this idea has been suggested previously by the author , the phase change concept possibly permits some new insights into cloud-system behavior. For example, in a protoplanetary debris disk, the work of gravity may suddenly be enhanced by electrostatically driven collapse of the system when materials reach a critical intergranular spacing or grain number density. This might reduce the rate of planet formation by orders of magnitude (considering the ratio of g-forces to electrostatic ones for very small grains in close proximity), and indeed, it might drive the collapse into a system configuration that would perhaps not be created by gravity alone. Additional information is contained in the original.

A risk-based approach to flammable gas detector spacing.

PubMed

Defriend, Stephen; Dejmek, Mark; Porter, Leisa; Deshotels, Bob; Natvig, Bernt

2008-11-15

Flammable gas detectors allow an operating company to address leaks before they become serious, by automatically alarming and by initiating isolation and safe venting. Without effective gas detection, there is very limited defense against a flammable gas leak developing into a fire or explosion that could cause loss of life or escalate to cascading failures of nearby vessels, piping, and equipment. While it is commonly recognized that some gas detectors are needed in a process plant containing flammable gas or volatile liquids, there is usually a question of how many are needed. The areas that need protection can be determined by dispersion modeling from potential leak sites. Within the areas that must be protected, the spacing of detectors (or alternatively, number of detectors) should be based on risk. Detector design can be characterized by spacing criteria, which is convenient for design - or alternatively by number of detectors, which is convenient for cost reporting. The factors that influence the risk are site-specific, including process conditions, chemical composition, number of potential leak sites, piping design standards, arrangement of plant equipment and structures, design of isolation and depressurization systems, and frequency of detector testing. Site-specific factors such as those just mentioned affect the size of flammable gas cloud that must be detected (within a specified probability) by the gas detection system. A probability of detection must be specified that gives a design with a tolerable risk of fires and explosions. To determine the optimum spacing of detectors, it is important to consider the probability that a detector will fail at some time and be inoperative until replaced or repaired. A cost-effective approach is based on the combined risk from a representative selection of leakage scenarios, rather than a worst-case evaluation. This means that probability and severity of leak consequences must be evaluated together. In marine and offshore facilities, it is conventional to use computational fluid dynamics (CFD) modeling to determine the size of a flammable cloud that would result from a specific leak scenario. Simpler modeling methods can be used, but the results are not very accurate in the region near the release, especially where flow obstructions are present. The results from CFD analyses on several leak scenarios can be plotted to determine the size of a flammable cloud that could result in an explosion that would generate overpressure exceeding the strength of the mechanical design of the plant. A cloud of this size has the potential to produce a blast pressure or flying debris capable of causing a fatality or subsequent damage to vessels or piping containing hazardous material. In cases where the leak results in a fire, rather than explosion, CFD or other modeling methods can estimate the size of a leak that would cause a fire resulting in subsequent damage to the facility, or would prevent the safe escape of personnel. The gas detector system must be capable of detecting a gas release or vapor cloud, and initiating action to prevent the leak from reaching a size that could cause injury or severe damage upon ignition.

The role of turbulent fluxes in the atmospheric boundary layer above a debris-covered glacier in the Himalayas

NASA Astrophysics Data System (ADS)

Steiner, J. F.; Stigter, E.; Litt, M.; Shea, J.; Bierkens, M. F.; Immerzeel, W. W.

2017-12-01

Debris-covered glaciers play an important role in the water cycle in high altitude catchments in the Himalaya. The melt dynamics of these glaciers are complex as a result of the debris. A thin debris layer (up to a few cm) may act as a facilitator of melt, whereas a thick layer serves primarily as an insulator. The debris cover itself shows a strong diurnal variation in temperature and humidity resulting in a complex interaction with the atmospheric boundary layer (ABL). Energy balance models are a common way to quantify sub-debris melt, but the importance of turbulent fluxes in this energy balance have so far been poorly investigated. We hypothesize that they may play a substantial role during phases of wetting and drying. In this study, ABL characteristics and surface turbulent fluxes are measured using an automatic weather station including an eddy-correlation (EC) system on the debris-covered Lirung glacier in Nepal over a 10 day period in late 2016, during the transition period from monsoon to the drier post-monsoon. The measurements are combined with surface temperature measurements and thermal UAV flights covering the footprint area of the EC tower to quantify the surface fluxes over a larger area. Our results show that turbulent fluxes do play a substantial role in the energy balance of debris-covered glaciers, and need to be accounted for to accurately simulate glacier melt. The EC tower results are subsequently evaluated against a number of different bulk approaches to quantify sensible and latent heat fluxes and are evaluated against turbulence characteristics. If found accurate enough, these approaches require less advanced measurement set-ups and can be applied on a wider scale.

Modelling the near-Earth space environment using LDEF data

NASA Technical Reports Server (NTRS)

Atkinson, Dale R.; Coombs, Cassandra R.; Crowell, Lawrence B.; Watts, Alan J.

1992-01-01

Near-Earth space is a dynamic environment, that is currently not well understood. In an effort to better characterize the near-Earth space environment, this study compares the results of actual impact crater measurement data and the Space Environment (SPENV) Program developed in-house at POD, to theoretical models established by Kessler (NASA TM-100471, 1987) and Cour-Palais (NASA SP-8013, 1969). With the continuing escalation of debris there will exist a definite hazard to unmanned satellites as well as manned operations. Since the smaller non-trackable debris has the highest impact rate, it is clearly necessary to establish the true debris environment for all particle sizes. Proper comprehension of the near-Earth space environment and its origin will permit improvement in spacecraft design and mission planning, thereby reducing potential disasters and extreme costs. Results of this study directly relate to the survivability of future spacecraft and satellites that are to travel through and/or reside in low Earth orbit (LEO). More specifically, these data are being used to: (1) characterize the effects of the LEO micrometeoroid an debris environment on satellite designs and components; (2) update the current theoretical micrometeoroid and debris models for LEO; (3) help assess the survivability of spacecraft and satellites that must travel through or reside in LEO, and the probability of their collision with already resident debris; and (4) help define and evaluate future debris mitigation and disposal methods. Combined model predictions match relatively well with the LDEF data for impact craters larger than approximately 0.05 cm, diameter; however, for smaller impact craters, the combined predictions diverge and do not reflect the sporadic clouds identified by the Interplanetary Dust Experiment (IDE) aboard LDEF. The divergences cannot currently be explained by the authors or model developers. The mean flux of small craters (approximately 0.05 cm diameter) is overpredicted by Kessler and underpredicted by Cour-Palais. This divergence may be a result of beta-meteoroid fluxes, elliptical orbits or a combination of the two. The results of this study illustrate the definite need for more intensive study of the near-Earth space environment, particularly the small particle regime, as it is the most degrading to spacecraft in LEO.

Net ecosystem productivity of temperate and boreal forests after clearcutting - a Fluxnet-Canada measurement and modelling synthesis

NASA Astrophysics Data System (ADS)

Grant, R. F.; Barr, A.; Black, T. A.; Margolis, H. A.; McCaughey, J. H.; Trofymow, J. A.

2010-05-01

Clearcutting strongly affects subsequent forest net ecosystem productivity (NEP). Hypotheses for ecological controls on NEP in the ecosystem model ecosys were tested with CO2 fluxes measured by eddy covariance (EC) in three post-clearcut conifer chronosequences. An algorithm for microbial colonization of fine and woody debris allowed the model to reproduce sigmoidal declines in debris observed after clearcutting. In the model, Rh drove debris decomposition that drove microbial growth, N mineralization and asymbiotic N2 fixation. These processes controlled root N uptake, and thereby CO2 fixation in regrowing vegetation. Interactions among soil and plant processes allowed the model to simulate hourly CO2 fluxes and annual NEP within the uncertainty of EC measurements from 2003 through 2007 over forest stands from 1 to 80 years of age in all three chronosequences without site- or species-specific parameterization. The model was then used to study the impacts of increasing harvest removals on subsequent C stocks at one of the chronosequence sites. Model results indicated that increasing harvest removals would hasten recovery of NEP during the first 30 years after clearcutting, but would reduce ecosystem C stocks by about 15% of the increased removals at the end of an 80 year harvest cycle.

Microphysical processing of aerosol particles in orographic clouds

NASA Astrophysics Data System (ADS)

Pousse-Nottelmann, S.; Zubler, E. M.; Lohmann, U.

2015-08-01

An explicit and detailed treatment of cloud-borne particles allowing for the consideration of aerosol cycling in clouds has been implemented into COSMO-Model, the regional weather forecast and climate model of the Consortium for Small-scale Modeling (COSMO). The effects of aerosol scavenging, cloud microphysical processing and regeneration upon cloud evaporation on the aerosol population and on subsequent cloud formation are investigated. For this, two-dimensional idealized simulations of moist flow over two bell-shaped mountains were carried out varying the treatment of aerosol scavenging and regeneration processes for a warm-phase and a mixed-phase orographic cloud. The results allowed us to identify different aerosol cycling mechanisms. In the simulated non-precipitating warm-phase cloud, aerosol mass is incorporated into cloud droplets by activation scavenging and released back to the atmosphere upon cloud droplet evaporation. In the mixed-phase cloud, a first cycle comprises cloud droplet activation and evaporation via the Wegener-Bergeron-Findeisen (WBF) process. A second cycle includes below-cloud scavenging by precipitating snow particles and snow sublimation and is connected to the first cycle via the riming process which transfers aerosol mass from cloud droplets to snowflakes. In the simulated mixed-phase cloud, only a negligible part of the total aerosol mass is incorporated into ice crystals. Sedimenting snowflakes reaching the surface remove aerosol mass from the atmosphere. The results show that aerosol processing and regeneration lead to a vertical redistribution of aerosol mass and number. Thereby, the processes impact the total aerosol number and mass and additionally alter the shape of the aerosol size distributions by enhancing the internally mixed/soluble Aitken and accumulation mode and generating coarse-mode particles. Concerning subsequent cloud formation at the second mountain, accounting for aerosol processing and regeneration increases the cloud droplet number concentration with possible implications for the ice crystal number concentration.

Orbital debris removal and salvage system

NASA Technical Reports Server (NTRS)

1990-01-01

Four Texas A&M University projects are discussed. The first project is a design to eliminate a majority of orbital debris. The Orbital Debris and Salvage System will push the smaller particles into lower orbits where their orbits will decay at a higher rate. This will be done by momentum transfer via laser. The salvageable satellites will be delivered to the Space Station by an Orbital Transfer Vehicle. The rest of the debris will be collected by Salvage I. The second project is the design of a space based satellite system to prevent the depletion of atmospheric ozone. The focus is on ozone depletion in the Antarctic. The plan is to use an orbiting solar array system designed to transmit microwaves at a frequency of 22 GHz over the region in order to dissipate polar stratospheric clouds that form during the months beginning in August and ending in October. The third project, Project Poseidon, involves a conceptual design of a space based hurricane control system consisting of a network of 21 low-orbiting laser platforms arranged in three rings designed to heat the upper atmosphere of a developing tropical depression. Fusion power plants are proposed to provide power for the lasers. The fourth project, Project Donatello, involves a proposed Mars exploration initiative for the year 2050. The project is a conceptual design for a futuristic superfreighter that will transport large numbers of people and supplies to Mars for the construction of a full scale scientific and manufacturing complex.

Molecular identification of polymers and anthropogenic particles extracted from oceanic water and fish stomach - A Raman micro-spectroscopy study.

PubMed

Ghosal, Sutapa; Chen, Michael; Wagner, Jeff; Wang, Zhong-Min; Wall, Stephen

2018-02-01

Pacific Ocean trawl samples, stomach contents of laboratory-raised fish as well as fish from the subtropical gyres were analyzed by Raman micro-spectroscopy (RMS) to identify polymer residues and any detectable persistent organic pollutants (POP). The goal was to access specific molecular information at the individual particle level in order to identify polymer debris in the natural environment. The identification process was aided by a laboratory generated automated fluorescence removal algorithm. Pacific Ocean trawl samples of plastic debris associated with fish collection sites were analyzed to determine the types of polymers commonly present. Subsequently, stomach contents of fish from these locations were analyzed for ingested polymer debris. Extraction of polymer debris from fish stomach using KOH versus ultrapure water were evaluated to determine the optimal method of extraction. Pulsed ultrasonic extraction in ultrapure water was determined to be the method of choice for extraction with minimal chemical intrusion. The Pacific Ocean trawl samples yielded primarily polyethylene (PE) and polypropylene (PP) particles >1 mm, PE being the most prevalent type. Additional microplastic residues (1 mm - 10 μm) extracted by filtration, included a polystyrene (PS) particle in addition to PE and PP. Flame retardant, deca-BDE was tentatively identified on some of the PP trawl particles. Polymer residues were also extracted from the stomachs of Atlantic and Pacific Ocean fish. Two types of polymer related debris were identified in the Atlantic Ocean fish: (1) polymer fragments and (2) fragments with combined polymer and fatty acid signatures. In terms of polymer fragments, only PE and PP were detected in the fish stomachs from both locations. A variety of particles were extracted from oceanic fish as potential plastic pieces based on optical examination. However, subsequent RMS examination identified them as various non-plastic fragments, highlighting the importance of chemical analysis in distinguishing between polymer and non-polymer residues. Copyright © 2017 Elsevier Ltd. All rights reserved.

First stars of the ρ Ophiuchi dark cloud. XMM-Newton view of ρ Oph and its neighbors

NASA Astrophysics Data System (ADS)

Pillitteri, I.; Wolk, S. J.; Chen, H. H.; Goodman, A.

2016-08-01

Star formation in molecular clouds can be triggered by the dynamical action of winds from massive stars. Furthermore, X-ray and UV fluxes from massive stars can influence the life time of surrounding circumstellar disks. We present the results of a 53 ks XMM-Newton observation centered on the ρ Ophiuchi A+B binary system. ρ Ophiuchi lies in the center of a ring of dust, likely formed by the action of its winds. This region is different from the dense core of the cloud (L1688 Core F) where star formation is at work. X-rays are detected from ρ Ophiuchi as well as a group of surrounding X-ray sources. We detected 89 X-ray sources, 47 of them have at least one counterpart in 2MASS+All-WISE catalogs. Based on IR and X-ray properties, we can distinguish between young stellar objects (YSOs) belonging to the cloud and background objects. Among the cloud members, we detect three debris-disk objects and 22 disk-less - Class III young stars.We show that these stars have ages in 5-10 Myr, and are significantly older than the YSOs in L1688. We speculate that they are the result of an early burst of star formation in the cloud. An X-ray energy of ≥5 × 1044 erg has been injected into the surrounding mediumover the past 5 Myr, we discuss the effects of such energy budget in relation to the cloud properties and dynamics.

cloudPEST - A python module for cloud-computing deployment of PEST, a program for parameter estimation

USGS Publications Warehouse

Fienen, Michael N.; Kunicki, Thomas C.; Kester, Daniel E.

2011-01-01

This report documents cloudPEST-a Python module with functions to facilitate deployment of the model-independent parameter estimation code PEST on a cloud-computing environment. cloudPEST makes use of low-level, freely available command-line tools that interface with the Amazon Elastic Compute Cloud (EC2(TradeMark)) that are unlikely to change dramatically. This report describes the preliminary setup for both Python and EC2 tools and subsequently describes the functions themselves. The code and guidelines have been tested primarily on the Windows(Registered) operating system but are extensible to Linux(Registered).

Updating the New Zealand Glacier Inventory

NASA Astrophysics Data System (ADS)

Baumann, S. C.; Anderson, B.; Mackintosh, A.; Lorrey, A.; Chinn, T.; Collier, C.; Rack, W.; Purdie, H.

2017-12-01

The last complete glacier inventory of New Zealand dates from the year 1978 (North Island 1988) and was manually constructed from oblique aerial photographs and geodetic maps (Chinn 2001). The inventory has been partly updated by Gjermundsen et al. (2011) for the year 2002 (40% of total area) and by Sirguey & More (2010) for the year 2009 (32% of total area), both using ASTER satellite imagery. We used Landsat 8 OLI/TIRS satellite data from February/March 2016 to map the total glaciated area. Clean and debris-covered ice were mapped semi-automatically. The band ratio approach was used for clean ice (ratio: red/SWIR). We mapped debris-covered ice using a supervised classification (maximum likelihood). Manual post processing was necessary due to misclassifications (e.g. lakes, clouds) or mapping in shadowed areas. It was also necessary to manually combine the clean and debris-covered parts into single glaciers. Additional input data for the post processing were Sentinel 2 images from the same time period, orthophotos from Land Information New Zealand (resolution: 0.75 m, date: Nov 2014), and the 1978/88 outlines from the GLIMS database (http://www.glims.org/). As the Sentinel 2 data were more heavily cloud covered compared to the Landsat 8 images, they were only used for post processing and not for the classification itself. Initial results show that New Zealand glaciers covered an area of about 1050 km² in 2016, a reduction of 16% since 1978. Approximately 17% of glacier area was covered in surface debris. The glaciers in the central Southern Alps around Mt Cook reduced in area by 24%. Glaciers in the North Island of New Zealand reduced by 71% since 1988, and only 2 km² of ice cover remained in 2016. Chinn, TJH (2001). "Distribution of the glacial water resources of New Zealand." Journal of Hydrology (NZ) 40(2): 139-187 Gjermundsen, EF, Mathieu, R, Kääb, A, Chinn, TJH, Fitzharris, B & Hagen, JO (2011). "Assessment of multispectral glacier mapping methods and derivation of glacier area changes, 1978-2002, in the central Southern Alps, New Zealand, from ASTER satellite data, field survey and existing inventory data." Journal of Glaciology 57(204): 667-683 Sirguey, P & More, B (2010). GLIMS Glacier Database. Boulder, NSIDC

Formation of highly porous aerosol particles by atmospheric freeze-drying in ice clouds

PubMed Central

Adler, Gabriela; Koop, Thomas; Haspel, Carynelisa; Taraniuk, Ilya; Moise, Tamar; Koren, Ilan; Heiblum, Reuven H.; Rudich, Yinon

2013-01-01

The cycling of atmospheric aerosols through clouds can change their chemical and physical properties and thus modify how aerosols affect cloud microphysics and, subsequently, precipitation and climate. Current knowledge about aerosol processing by clouds is rather limited to chemical reactions within water droplets in warm low-altitude clouds. However, in cold high-altitude cirrus clouds and anvils of high convective clouds in the tropics and midlatitudes, humidified aerosols freeze to form ice, which upon exposure to subsaturation conditions with respect to ice can sublimate, leaving behind residual modified aerosols. This freeze-drying process can occur in various types of clouds. Here we simulate an atmospheric freeze-drying cycle of aerosols in laboratory experiments using proxies for atmospheric aerosols. We find that aerosols that contain organic material that undergo such a process can form highly porous aerosol particles with a larger diameter and a lower density than the initial homogeneous aerosol. We attribute this morphology change to phase separation upon freezing followed by a glass transition of the organic material that can preserve a porous structure after ice sublimation. A porous structure may explain the previously observed enhancement in ice nucleation efficiency of glassy organic particles. We find that highly porous aerosol particles scatter solar light less efficiently than nonporous aerosol particles. Using a combination of satellite and radiosonde data, we show that highly porous aerosol formation can readily occur in highly convective clouds, which are widespread in the tropics and midlatitudes. These observations may have implications for subsequent cloud formation cycles and aerosol albedo near cloud edges. PMID:24297908

Formation of highly porous aerosol particles by atmospheric freeze-drying in ice clouds.

PubMed

Adler, Gabriela; Koop, Thomas; Haspel, Carynelisa; Taraniuk, Ilya; Moise, Tamar; Koren, Ilan; Heiblum, Reuven H; Rudich, Yinon

2013-12-17

The cycling of atmospheric aerosols through clouds can change their chemical and physical properties and thus modify how aerosols affect cloud microphysics and, subsequently, precipitation and climate. Current knowledge about aerosol processing by clouds is rather limited to chemical reactions within water droplets in warm low-altitude clouds. However, in cold high-altitude cirrus clouds and anvils of high convective clouds in the tropics and midlatitudes, humidified aerosols freeze to form ice, which upon exposure to subsaturation conditions with respect to ice can sublimate, leaving behind residual modified aerosols. This freeze-drying process can occur in various types of clouds. Here we simulate an atmospheric freeze-drying cycle of aerosols in laboratory experiments using proxies for atmospheric aerosols. We find that aerosols that contain organic material that undergo such a process can form highly porous aerosol particles with a larger diameter and a lower density than the initial homogeneous aerosol. We attribute this morphology change to phase separation upon freezing followed by a glass transition of the organic material that can preserve a porous structure after ice sublimation. A porous structure may explain the previously observed enhancement in ice nucleation efficiency of glassy organic particles. We find that highly porous aerosol particles scatter solar light less efficiently than nonporous aerosol particles. Using a combination of satellite and radiosonde data, we show that highly porous aerosol formation can readily occur in highly convective clouds, which are widespread in the tropics and midlatitudes. These observations may have implications for subsequent cloud formation cycles and aerosol albedo near cloud edges.

High-Obliquity Impact of a Compact Penetrator on a Thin Plate: Penetrator Splitting and Adiabatic Shear

DTIC Science & Technology

1998-01-01

nonideal penetrator on a thin plate at high obliquities. These computations simulated two series of experiments at velocities of 1.5 km/ s and 4.1 km/ s ...3 2. Combined Effects of Obliquity, 0, and Rotation, 4, on Debris Cloud Evolution at 4.1 km/ s and 26 p s ; Impact Velocity Vector Lies in x-z Plane...7 3. Time History of the Penetrator Mass Fraction Exiting the Bottom of the Target at 4.1 km / s

Modelling accumulation of marine plastics in the coastal zone; what are the dominant physical processes?

NASA Astrophysics Data System (ADS)

Critchell, Kay; Lambrechts, Jonathan

2016-03-01

Anthropogenic marine debris, mainly of plastic origin, is accumulating in estuarine and coastal environments around the world causing damage to fauna, flora and habitats. Plastics also have the potential to accumulate in the food web, as well as causing economic losses to tourism and sea-going industries. If we are to manage this increasing threat, we must first understand where debris is accumulating and why these locations are different to others that do not accumulate large amounts of marine debris. This paper demonstrates an advection-diffusion model that includes beaching, settling, resuspension/re-floating, degradation and topographic effects on the wind in nearshore waters to quantify the relative importance of these physical processes governing plastic debris accumulation. The aim of this paper is to prioritise research that will improve modelling outputs in the future. We have found that the physical characteristic of the source location has by far the largest effect on the fate of the debris. The diffusivity, used to parameterise the sub-grid scale movements, and the relationship between debris resuspension/re-floating from beaches and the wind shadow created by high islands also has a dramatic impact on the modelling results. The rate of degradation of macroplastics into microplastics also have a large influence in the result of the modelling. The other processes presented (settling, wind drift velocity) also help determine the fate of debris, but to a lesser degree. These findings may help prioritise research on physical processes that affect plastic accumulation, leading to more accurate modelling, and subsequently management in the future.

Cesarean section scar as a cause of abnormal vaginal bleeding: diagnosis by sonohysterography.

PubMed

Thurmond, A S; Harvey, W J; Smith, S A

1999-01-01

A previously undescribed cause of abnormal uterine bleeding is presented. Nine of 310 women evaluated by sonohysterography for abnormal bleeding demonstrated an 8 to 17 mm gap in the anterior lower uterine segment myometrium at the site of prior cesarean deliveries. All women were premenopausal and had a history of 2 to 12 days of postmenstrual spotting. Presumably a lack of coordinated muscular contractions occurs around the cesarean scar, allowing the defect to collect menstrual debris. Subsequently, the debris leaches out through the cervix for several days after the majority of menstrual flow has ceased.

The influence of slope-angle ratio on the dynamics of granular flows: insights from laboratory experiments

NASA Astrophysics Data System (ADS)

Sulpizio, R.; Castioni, D.; Rodriguez-Sedano, L. A.; Sarocchi, D.; Lucchi, F.

2016-11-01

Laboratory experiments on granular flows using natural material were carried out in order to investigate the behaviour of granular flows passing over a break in slope. Sensors in the depositional area recorded the flow kinematics, while video footage permitted reconstruction of the deposit formation, which allowed investigation of the deposit shape as a function of the change in slope. We defined the slope-angle ratio as the proportion between slope angle in the depositional area and that of the channel. When the granular flow encounters the break in slope part of the flow front forms a bouncing clast zone due to elastic impact with the expansion box floor. During this process, part of the kinetic energy of the dense granular flow is transferred to elutriating fine ash, which subsequently forms turbulent ash cloud accompanying the granular flow until it comes to rest. Morphometric analysis of the deposits shows that they are all elliptical, with an almost constant minor axis and a variable major axis. The almost constant value of the minor axis relates to the spreading angle of flow at the end of the channel, which resembles the basal friction angle of the material. The variation of the major axis is interpreted to relate to the effect of competing inertial and frictional forces. This effect also reflects the partitioning of centripetal and tangential velocities, which changes as the flow passes over the break in slope. After normalization, morphometric data provided empirical relationships that highlight the dependence of runout from the product of slope-angle ratio and the difference in height between granular material release and deposit. The empirical relationships were tested against the runouts of hot avalanches formed during the 1944 ad eruption at Vesuvius, with differences among actual and calculated values are between 1.7 and 15 %. Velocity measurements of laboratory granular flows record deceleration paths at different breaks in slope. When normalized, the velocity data show third-order polynomial fit, highlighting a complex behaviour involving interplay between inertial and frictional forces. The theoretical velocity decays were tested against the data published for volcaniclastic debris flows of the 5-6 May 1998 event in the Sarno area. The comparison is very good for non-channelized debris flows, with significant differences between actual and calculated velocities for the channelized debris flows.

Radar observations of individual rain drops in the free atmosphere

PubMed Central

Schmidt, Jerome M.; Flatau, Piotr J.; Harasti, Paul R.; Yates, Robert D.; Littleton, Ricky; Pritchard, Michael S.; Fischer, Jody M.; Fischer, Erin J.; Kohri, William J.; Vetter, Jerome R.; Richman, Scott; Baranowski, Dariusz B.; Anderson, Mark J.; Fletcher, Ed; Lando, David W.

2012-01-01

Atmospheric remote sensing has played a pivotal role in the increasingly sophisticated representation of clouds in the numerical models used to assess global and regional climate change. This has been accomplished because the underlying bulk cloud properties can be derived from a statistical analysis of the returned microwave signals scattered by a diverse ensemble comprised of numerous cloud hydrometeors. A new Doppler radar, previously used to track small debris particles shed from the NASA space shuttle during launch, is shown to also have the capacity to detect individual cloud hydrometeors in the free atmosphere. Similar to the traces left behind on film by subatomic particles, larger cloud particles were observed to leave a well-defined radar signature (or streak), which could be analyzed to infer the underlying particle properties. We examine the unique radar and environmental conditions leading to the formation of the radar streaks and develop a theoretical framework which reveals the regulating role of the background radar reflectivity on their observed characteristics. This main expectation from theory is examined through an analysis of the drop properties inferred from radar and in situ aircraft measurements obtained in two contrasting regions of an observed multicellular storm system. The observations are placed in context of the parent storm circulation through the use of the radar’s unique high-resolution waveforms, which allow the bulk and individual hydrometeor properties to be inferred at the same time. PMID:22652569

Radar observations of individual rain drops in the free atmosphere.

PubMed

Schmidt, Jerome M; Flatau, Piotr J; Harasti, Paul R; Yates, Robert D; Littleton, Ricky; Pritchard, Michael S; Fischer, Jody M; Fischer, Erin J; Kohri, William J; Vetter, Jerome R; Richman, Scott; Baranowski, Dariusz B; Anderson, Mark J; Fletcher, Ed; Lando, David W

2012-06-12

Atmospheric remote sensing has played a pivotal role in the increasingly sophisticated representation of clouds in the numerical models used to assess global and regional climate change. This has been accomplished because the underlying bulk cloud properties can be derived from a statistical analysis of the returned microwave signals scattered by a diverse ensemble comprised of numerous cloud hydrometeors. A new Doppler radar, previously used to track small debris particles shed from the NASA space shuttle during launch, is shown to also have the capacity to detect individual cloud hydrometeors in the free atmosphere. Similar to the traces left behind on film by subatomic particles, larger cloud particles were observed to leave a well-defined radar signature (or streak), which could be analyzed to infer the underlying particle properties. We examine the unique radar and environmental conditions leading to the formation of the radar streaks and develop a theoretical framework which reveals the regulating role of the background radar reflectivity on their observed characteristics. This main expectation from theory is examined through an analysis of the drop properties inferred from radar and in situ aircraft measurements obtained in two contrasting regions of an observed multicellular storm system. The observations are placed in context of the parent storm circulation through the use of the radar's unique high-resolution waveforms, which allow the bulk and individual hydrometeor properties to be inferred at the same time.

Deciphering Debris Disk Structure with the Submillimeter Array

NASA Astrophysics Data System (ADS)

MacGregor, Meredith Ann

2018-01-01

More than 20% of nearby main sequence stars are surrounded by dusty disks continually replenished via the collisional erosion of planetesimals, larger bodies similar to asteroids and comets in our own Solar System. The material in these ‘debris disks’ is directly linked to the larger bodies such as planets in the system. As a result, the locations, morphologies, and physical properties of dust in these disks provide important probes of the processes of planet formation and subsequent dynamical evolution. Observations at millimeter wavelengths are especially critical to our understanding of these systems, since they are dominated by larger grains that do not travel far from their origin and therefore reliably trace the underlying planetesimal distribution. The Submillimeter Array (SMA) plays a key role in advancing our understanding of debris disks by providing sensitivity at the short baselines required to determine the structure of wide-field disks, such as the HR 8799 debris disk. Many of these wide-field disks are among the closest systems to us, and will serve as cornerstone templates for the interpretation of more distant, less accessible systems.

STEP-TRAMM - A modeling interface for simulating localized rainfall induced shallow landslides and debris flow runout pathways

NASA Astrophysics Data System (ADS)

von Ruette, Jonas; Lehmann, Peter; Fan, Linfeng; Bickel, Samuel; Or, Dani

2017-04-01

Landslides and subsequent debris-flows initiated by rainfall represent a ubiquitous natural hazard in steep mountainous regions. We integrated a landslide hydro-mechanical triggering model and associated debris flow runout pathways with a graphical user interface (GUI) to represent these natural hazards in a wide range of catchments over the globe. The STEP-TRAMM GUI provides process-based locations and sizes of landslides patterns using digital elevation models (DEM) from SRTM database (30 m resolution) linked with soil maps from global database SoilGrids (250 m resolution) and satellite based information on rainfall statistics for the selected region. In a preprocessing step STEP-TRAMM models soil depth distribution and complements soil information that jointly capture key hydrological and mechanical properties relevant to local soil failure representation. In the presentation we will discuss feature of this publicly available platform and compare landslide and debris flow patterns for different regions considering representative intense rainfall events. Model outcomes will be compared for different spatial and temporal resolutions to test applicability of web-based information on elevation and rainfall for hazard assessment.

A Numerical Approach to Estimate the Ballistic Coefficient of Space Debris from TLE Orbital Data

NASA Technical Reports Server (NTRS)

Narkeliunas, Jonas

2016-01-01

Low Earth Orbit (LEO) is full of space debris, which consist of spent rocket stages, old satellites and fragments from explosions and collisions. As of 2009, more than 21,000 orbital debris larger than 10 cm are known to exist], and while it is hard to track anything smaller than that, the estimated population of particles between 1 and 10 cm in diameter is approximately 500,000, whereas small as 1 cm exceeds 100 million. These objects orbit Earth with huge kinetic energies speeds usually exceed 7 kms. The shape of their orbit varies from almost circular to highly elliptical and covers all LEO, a region in space between 160 and 2,000 km above sea level. Unfortunately, LEO is also the place where most of our active satellites are situated, as well as, International Space Station (ISS) and Hubble Space Telescope, whose orbits are around 400 and 550 km above sea level, respectively.This poses a real threat as debris can collide with satellites and deal substantial damage or even destroy them.Collisions between two or more debris create clouds of smaller debris, which are harder to track and increase overall object density and collision probability. At some point, the debris density couldthen reach a critical value, which would start a chain reaction and the number of space debris would grow exponentially. This phenomenon was first described by Kessler in 1978 and he concluded that it would lead to creation of debris belt, which would vastly complicate satellite operations in LEO. The debris density is already relatively high, as seen from several necessary debris avoidance maneuvers done by Shuttle, before it was discontinued, and ISS. But not all satellites have a propulsion system to avoid collision, hence different methods need to be applied. One of the proposed collision avoidance concepts is called LightForce and it suggests using photon pressure to induce small orbital corrections to deflect debris from colliding. This method is very efficient as seen from theoretical simulations, even few continuous mode 10 kW ground-based lasers, focused by 1.5 m telescopes with adaptive optics, were enough to prevent significant amount of the debris collisions. Simulations were done by propagating all space objects in LEO by 1 year into the future and checking whether the probability of collision was high. For those space objects different ground-based lasers were used to divert them, afterwards collision probabilities were reevaluated. However, the actual accuracy of the LightForce software, which has been developed at NASA AmesResearch Center, depends on the veracity of the input parameters, one of which is the objects ballistic coefficient. It is a measure of bodys ability to overcome air resistance, which has a significant impact on the debris in LEO, and thus it is responsible for the shape of the trajectory of the debris. Having the exact values of the ballistic coefficient would make significantly better collision predictions, unfortunately, we do not know what are the values for most of the objects.In this research, we were working with part of LightForce code, which estimates the ballistic coefficient from ephemerides. Previously used method gave highly inaccurate values, when compared to known objects, and it needed to be changed. The goal of this work was to try out a different method of estimating the ballistic coefficient and to check whether or not it gives noticeable improvements.

Nondestructive Testing As a Tool in the Space Shuttle Columbia Accident Investigation

NASA Technical Reports Server (NTRS)

McDanels, Steve

2008-01-01

Nondestructive testing (NDT) played a crucial role in determining the Columbia tragedy's cause. Over 84,000 pieces of debris were recovered; hundreds were subsequently subjected to NDT and materials analysis. Visual NDT of the debris revealed localized areas of damage such as erosion, excessive heating, knife edging and mechanical damage. Three-dimensional reconstructions were made of the left wing leading edge, utilizing a tripod-mounted laser scanning head and focused laser beam, and an advanced topometric optical scanner (ATOS) with digital white light to scan complex-shaped debris, producing monochrome 3-D models. Texture mapping provided a means to capture true colors of the debris and superimpose them on the scanned images. Uniform deposits were found over large portions of debris, obscuring underlying materials. To determine what was beneath, inverse radiography was enlisted. The radiographs guided investigators to where samples should be taken. To ascertain compositions, these samples were subjected to analytical testing, including energy dispersive X-ray spectroscopy and electron microprobe analysis. This combination of visual evidence, radiography, virtual reconstruction, and materials analysis allowed the forensic scientists to verify that a breach occurred in the leading edge of the left wing, the path the plasma followed, and the sequence of events that led to the loss.

The mechanics of motorised momentum exchange tethers when applied to active debris removal from LEO

NASA Astrophysics Data System (ADS)

Caldecott, Ralph; Kamarulzaman, Dayangku N. S.; Kirrane, James P.; Cartmell, Matthew P.; Ganilova, Olga A.

2014-12-01

The concept of momentum exchange when applied to space tethers for propulsion is well established, and a considerable body of literature now exists on the on-orbit modelling, the dynamics, and also the control of a large range of tether system applications. The authors consider here a new application for the Motorised Momentum Exchange Tether by highlighting three key stages of development leading to a conceptualisation that can subsequently be developed into a technology for Active Debris Removal. The paper starts with a study of the on-orbit mechanics of a full sized motorised tether in which it is shown that a laden and therefore highly massasymmetrical tether can still be forced to spin, and certainly to librate, thereby confirming its possible usefulness for active debris removal (ADR). The second part of the paper concentrates on the modelling of the centripetal deployment of a symmetrical MMET in order to get it initialized for debris removal operations, and the third and final part of the paper provides an entry into scale modelling for low cost mission design and testing. It is shown that the motorised momentum exchange tether offers a potential solution to the removal of large pieces of orbital debris, and that dynamic methodologies can be implemented to in order to optimise the emergent design.

Wildfire impacts on the processes that generate debris flows in burned watersheds

USGS Publications Warehouse

Parise, M.; Cannon, S.H.

2012-01-01

Every year, and in many countries worldwide, wildfires cause significant damage and economic losses due to both the direct effects of the fires and the subsequent accelerated runoff, erosion, and debris flow. Wildfires can have profound effects on the hydrologic response of watersheds by changing the infiltration characteristics and erodibility of the soil, which leads to decreased rainfall infiltration, significantly increased overland flow and runoff in channels, and movement of soil. Debris-flow activity is among the most destructive consequences of these changes, often causing extensive damage to human infrastructure. Data from the Mediterranean area and Western United States of America help identify the primary processes that result in debris flows in recently burned areas. Two primary processes for the initiation of fire-related debris flows have been so far identified: (1) runoff-dominated erosion by surface overland flow; and (2) infiltration-triggered failure and mobilization of a discrete landslide mass. The first process is frequently documented immediately post-fire and leads to the generation of debris flows through progressive bulking of storm runoff with sediment eroded from the hillslopes and channels. As sediment is incorporated into water, runoff can convert to debris flow. The conversion to debris flow may be observed at a position within a drainage network that appears to be controlled by threshold values of upslope contributing area and its gradient. At these locations, sufficient eroded material has been incorporated, relative to the volume of contributing surface runoff, to generate debris flows. Debris flows have also been generated from burned basins in response to increased runoff by water cascading over a steep, bedrock cliff, and incorporating material from readily erodible colluvium or channel bed. Post-fire debris flows have also been generated by infiltration-triggered landslide failures which then mobilize into debris flows. However, only 12% of documented cases exhibited this process. When they do occur, the landslide failures range in thickness from a few tens of centimeters to more than 6 m, and generally involve the soil and colluvium-mantled hillslopes. Surficial landslide failures in burned areas most frequently occur in response to prolonged periods of storm rainfall, or prolonged rainfall in combination with rapid snowmelt or rain-on-snow events. ?? 2011 Springer Science+Business Media B.V.

Magnitude and frequency data for historic debris flows in Grand Canyon National Park and vicinity, Arizona

USGS Publications Warehouse

Melis, T.S.; Webb, R.H.; Griffiths, P.G.; Wise, T.J.

1995-01-01

Debris flows occur in 529 tributaries of the Colorado River in Grand Canyon between Lees Ferry and Diamond Creek, Arizona (river miles 0 to 225). An episodic type of flash flood, debris flows transport poorly-sorted sediment ranging in size from clay to boulders into the Colorado River. Debris flows create and maintain debris fans and the hundreds of associated riffles and rapids that control the geomorphic framework of the Colorado River downstream from Glen Canyon Dam. Between 1984 and 1994, debris flows created 4 new rapids and enlarged 17 existing rapids and riffles. Debris flows in Grand Canyon are initiated by slope failures that occur during intense rainfall. Three of these mechanisms of slope failure are documented. Failures in weathered bedrock, particularly in the Hermit Shale and Supai Group, have initiated many historic debris flows in Grand Canyon. A second mechanism, termed the fire-hose effect, occurs when runoff pours over cliffs onto unconsolidated colluvial wedges, triggering a failure. A third initiation mechanism occurs when intense precipitation causes failures in colluvium overlying bedrock. Multiple source areas and extreme topographic relief in Grand Canyon commonly result in combinations of these three initiation mechanisms. Interpretation of 1,107 historical photographs spanning 120 years, supplemented with aerial photography made between 1935 and 1994, yielded information on the frequency of debris flows in 168 of the 529 tributaries (32 percent) of the Colorado River in Grand Canyon. Of the 168 tributaries, 96 contain evidence of debris flows that have occurred since 1872, whereas 72 tributaries have not had a debris flow during the last century. The oldest debris flow we have documented in Grand Canyon occurred 5,400 years ago in an unnamed tributary at river mile 63.3-R. Our results indicate that the frequency of debris flows ranges from one every 10 to 15 years in certain eastern tributaries, to less than one per century in other drainage basins. On average, debris flows may recur approximately every 30 to 50 years in individual tributaries, although adjacent tributaries may have considerably different histories. Peak discharges were estimated in 18 drainages for debris flows that occurred between 1939 and 1994. Typically, discharges range from about 100 to 300 cubic meters per second (m3/s). The largest debris flow in Grand Canyon during the last century, which occurred in Prospect Canyon in 1939, had a peak discharge of about 1,000 m3/s. Debris-flow deposits generally contain 15 to 30 percent sand-and-finer sediment; however, the variability of sand-and-finer sediment contained by recent debris flows is large. Reconstitution of debris-flow samples indicates a range in water content of 10 to 25 percent by weight;. Before flow regulation of the Colorado River began, debris fans aggraded by debris flows were periodically reworked by large river floods that may have been as large as 11,000 m3/s. Impoundment of the river by Glen Canyon Dam in 1963, and subsequent operation of the reservoir have reduced the magnitude of these floods. Flow releases from the dam since 1963 have only partly reworked recently-aggraded debris fans. Significant reworking of new debris-flow deposits now occurs only during river discharges higher than typical power plant releases, which currently range between 142 and 510 m3/s.

Fallout of Debris from Tornadic Thunderstorms: A Historical Perspective and Two Examples from VORTEX.

NASA Astrophysics Data System (ADS)

Snow, John T.; Wyatt, Amy Lee; McCarthy, Ann K.; Bishop, Eric K.

1995-10-01

Preliminary results of an investigation of debris lofted by tornadoes, its long-distance transport by thunderstorms, and its subsequent fallout are reported. The authors begin with a review of historical accounts, including the unique study of the 1984 Barneveld, Wisconsin, tornado by Anderson, which shows that long-distance transport and fallout of debris have occurred and that distances involved have been significant. The authors then report first-hand evidence of these phenomena in two events with F2 tornadoes: the Tuskahoma, Oklahorna, tornado of 25 April 1994 and the Gainesville, Texas, tornadoes of 26 April 1994. In both cases, traceable material in the form of canceled checks, bills-of-sale, invoices, and legal documents were reported to the authors, who were able to locate the source locations for several of these items. The authors close with some conjectures on the implications of these first findings.

The healing of disturbed hillslopes by gully gravure

USGS Publications Warehouse

Osterkamp, W.R.; Toy, T.J.

1994-01-01

Results of accelerated erosion on certain constructed surfaces in southeastern Arizona appear similar to those described by Bryan as gully gravure. Twenty cross-section excavations in eight rills inclised into silt-rich lacustrine and fluvial deposits reveal partial filling of the rills by debris derived from overyling fluvial sand, gravel, and cobbles. Interstices of the coarse material gradually fill with fine-grained erosion products, decreasing permeability of the fill and deflecting subsequent runoff to the margins of the fill. Rills and rill fillings thus increase in width with time, and complete veneering of the surface by coarse debris ultimately may occur. Through incision, filling, lateral planation, and armoring, channels of the dissected surface heal and the new hillslope approaches an equilibrium condition. Natural hillslopes in the area with similar geologic conditions have inclinations of 16??-22??, have generally unbroken veneers of coarse debris, and appear subject to the same erosional processes identified at constructed hillslopes. -from Authors

Some physical and thermodynamic properties of rocket exhaust clouds measured with infrared scanners

NASA Technical Reports Server (NTRS)

Gomberg, R. I.; Kantsios, A. G.; Rosensteel, F. J.

1977-01-01

Measurements using infrared scanners were made of the radiation from exhaust clouds from liquid- and solid-propellant rocket boosters. Field measurements from four launches were discussed. These measurements were intended to explore the physical and thermodynamic properties of these exhaust clouds during their formation and subsequent dispersion. Information was obtained concerning the initial cloud's buoyancy, the stabilized cloud's shape and trajectory, the cloud volume as a function of time, and it's initial and stabilized temperatures. Differences in radiation intensities at various wavelengths from ambient and stabilized exhaust clouds were investigated as a method of distinguishing between the two types of clouds. The infrared remote sensing method used can be used at night when visible range cameras are inadequate. Infrared scanning techniques developed in this project can be applied directly to natural clouds, clouds containing certain radionuclides, or clouds of industrial pollution.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Higuchi, Aya E.; Sakai, Nami; Sato, Aki

We have detected [C i] {sup 3} P {sub 1}–{sup 3} P {sub 0} emissions in the gaseous debris disks of 49 Ceti and β Pictoris with the 10 m telescope of the Atacama Submillimeter Telescope Experiment, which is the first detection of such emissions. The line profiles of [C i] are found to resemble those of CO( J = 3–2) observed with the same telescope and the Atacama Large Millimeter/submillimeter Array. This result suggests that atomic carbon (C) coexists with CO in the debris disks and is likely formed by the photodissociation of CO. Assuming an optically thin [Cmore » i] emission with the excitation temperature ranging from 30 to 100 K, the column density of C is evaluated to be (2.2 ± 0.2) × 10{sup 17} and (2.5 ± 0.7) × 10{sup 16} cm{sup −2} for 49 Ceti and β Pictoris, respectively. The C/CO column density ratio is thus derived to be 54 ± 19 and 69 ± 42 for 49 Ceti and β Pictoris, respectively. These ratios are higher than those of molecular clouds and diffuse clouds by an order of magnitude. The unusually high ratios of C to CO are likely attributed to a lack of H{sub 2} molecules needed to reproduce CO molecules efficiently from C. This result implies a small number of H{sub 2} molecules in the gas disk, i.e., there is an appreciable contribution of secondary gas from dust grains.« less

Pulsed cavitational therapy using high-frequency ultrasound for the treatment of deep vein thrombosis in an in vitro model of human blood clot

NASA Astrophysics Data System (ADS)

Goudot, G.; Mirault, T.; Arnal, B.; Boisson-Vidal, C.; Le Bonniec, B.; Gaussem, P.; Galloula, A.; Tanter, M.; Messas, E.; Pernot, M.

2017-12-01

Post-thrombotic syndrome, a frequent complication of deep venous thrombosis, can be reduced with early vein recanalization. Pulsed cavitational therapy (PCT) using ultrasound is a recent non-invasive approach. We propose to test the efficacy and safety of high-frequency focused PCT for drug-free thrombolysis (thrombotripsy) in a realistic in vitro model of venous thrombosis. To reproduce venous thrombosis conditions, human whole blood was allowed to clot by stasis in silicone tubes (6 mm internal diameter) at a 30 cm H2O pressure, maintained during the whole experiment. We engineered an ultrasound device composed of dual 2.25 MHz transducers centered around a 6 MHz imaging probe. A therapeutic focus was generated at a 3.2 cm depth from the probe. Thrombotripsy was performed by longitudinally scanning the thrombus at three different speeds: 1 mm s-1 (n  =  6) 2 mm s-1 (n  =  6) 3 mm s-1 (n  =  12). Restored outflow was measured every three passages. Filters were placed to evaluate the debris size. Twenty-four occlusive thrombi, of 2.5 cm mean length and 4.4 kPa mean stiffness, were studied. Flow restoration was systematically obtained by nine subsequent passages (4.5 min maximum). By varying the device’s speed, we found an optimal speed of 1 mm s-1 to be efficient for effective recanalization with 90 s (three passages). Within 90 s, flow restoration was of 80, 62 and 74% at respectively 1, 2 and 3 mm s-1. For all groups, cavitation cloud drilled a 1.7 mm mean diameter channel throughout the clot. Debris analysis showed 92% of debris  <10 µm, with no fragment  >  200 µm.

Evaporation and accretion of extrasolar comets following white dwarf kicks

NASA Astrophysics Data System (ADS)

Stone, Nicholas; Metzger, Brian D.; Loeb, Abraham

2015-03-01

Several lines of observational evidence suggest that white dwarfs receive small birth kicks due to anisotropic mass-loss. If other stars possess extrasolar analogues to the Solar Oort cloud, the orbits of comets in such clouds will be scrambled by white dwarf natal kicks. Although most comets will be unbound, some will be placed on low angular momentum orbits vulnerable to sublimation or tidal disruption. The dusty debris from these comets will manifest itself as an IR excess temporarily visible around newborn white dwarfs; examples of such discs may already have been seen in the Helix Nebula, and around several other young white dwarfs. Future observations with the James Webb Space Telescope may distinguish this hypothesis from alternatives such as a dynamically excited Kuiper Belt analogue. Although competing hypotheses exist, the observation that ≳15 per cent of young white dwarfs possess such discs, if interpreted as indeed being cometary in origin, provides indirect evidence that low-mass gas giants (thought necessary to produce an Oort cloud) are common in the outer regions of extrasolar planetary systems. Hydrogen abundances in the atmospheres of older white dwarfs can, if sufficiently low, also be used to place constraints on the joint parameter space of natal kicks and exo-Oort cloud models.

Characterization of Oribtal Debris via Hyper-Velocity Ground-Based Tests

NASA Technical Reports Server (NTRS)

Cowardin, H.

2015-01-01

Existing DoD and NASA satellite breakup models are based on a key laboratory-based test, Satellite Orbital debris Characterization Impact Test (SOCIT), which has supported many applications and matched on-orbit events involving older satellite designs reasonably well over the years. In order to update and improve the break-up models and the NASA Size Estimation Model (SEM) for events involving more modern satellite designs, the NASA Orbital Debris Program Office has worked in collaboration with the University of Florida to replicate a hypervelocity impact using a satellite built with modern-day spacecraft materials and construction techniques. The spacecraft, called DebriSat, was intended to be a representative of modern LEO satellites and all major designs decisions were reviewed and approved by subject matter experts at Aerospace Corporation. DebriSat is composed of 7 major subsystems including attitude determination and control system (ADCS), command and data handling (C&DH), electrical power system (EPS), payload, propulsion, telemetry tracking and command (TT&C), and thermal management. To reduce cost, most components are emulated based on existing design of flight hardware and fabricated with the same materials. All fragments down to 2 mm is size will be characterized via material, size, shape, bulk density, and the associated data will be stored in a database for multiple users to access. Laboratory radar and optical measurements will be performed on a subset of fragments to provide a better understanding of the data products from orbital debris acquired from ground-based radars and telescopes. The resulting data analysis from DebriSat will be used to update break-up models and develop the first optical SEM in conjunction with updates into the current NASA SEM. The characterization of the fragmentation will be discussed in the subsequent presentation.

Interaction between riverbed condition and characteristics of debris flow in Ichino-sawa subwatershed of Ohya-kuzure landslide, Japan

NASA Astrophysics Data System (ADS)

Tsunetaka, Haruka; Hotta, Norifumi; Imaizumi, Fumitoshi; Hayakawa, Yuichi S.; Yumen, Noriki

2015-04-01

Large-scale sediment movements, such as a deep-seated landslide, not only induce immediate sediment disasters but also produce a large amount of unstable sediment upstream. Most of the unstable sediment residing in the upstream area is discharged as debris flow. Hence, after the occurrence of large-scale sediment movement, debris flows have a long-term effect on the watershed regime. However, the characteristics of debris flow in upstream areas are not well understood, due to the topographic and grain-size conditions that are more complicated than the downstream area. This study was performed to reveal the relationship between such a riverbed condition and the characteristics of debris flow by field observations. The study site was Ichinosawa-subwatershed in the Ohya-kuzure basin, Shizuoka Prefecture, Japan. The basin experienced a deep-seated landslide about 300 years ago and is currently actively yielding sediment with a clear annual cycle. During the winter season, sediment is deposited on the valley bottom by freeze-thaw and weathering. In the summer season, the deposited sediment is discharged incrementally by debris flows related to storm events. Topographical survey and grain-size analysis were performed several times between November 2011 and November 2014. High-resolution digital elevation models (10 cm) were created from the results of a topographical survey using a terrestrial laser scanner. A grain-size analysis was conducted in the upper, middle, and lower parts of the study site. Debris flow occurrences were also monitored in the same period by a sensor-triggered video camera and interval camera. Rainfall was observed during the summer season for comparison with debris flow occurrence. Several debris flows of different magnitudes were observed during the study period. Although heavy rainfall events altered the bed inclination, the thickness of deposited sediment, and the grain-size distribution, more significant changes were detected after the debris flow. While the initial grain-size distribution in early spring was roughly identical across the study site, the subsequent changes in the grain-size distribution differed according to location. The source, transport and deposition areas of the debris flows differed among rainfall events, resulting in different transitions in topographic conditions at different locations. Furthermore, surges of debris flow not only induced erosion-deposited sediment but also suspended and deposited sediment in the same area during one typhoon event. A comparison of the results indicated that, in addition to the conditions of the triggering rainfall, topographic and grain-size conditions affected the debris flow occurrence and magnitude. These interactions also showed that the magnitude and form of the succeeding debris flow could be dominant, depending on changing riverbed condition by past debris flows in upstream areas.

Sediment Mobilization and Storage Dynamics of a Debris Flow Impacted Stream Channel using Multi-Temporal Structure from Motion Photogrammetry

NASA Astrophysics Data System (ADS)

Bailey, T. L.; Sutherland-Montoya, D.

2015-12-01

High resolution topographic analysis methods have become important tools in geomorphology. Structure from Motion photogrammetry offers a compelling vehicle for geomorphic change detection in fluvial environments. This process can produce arbitrarily high resolution, geographically registered spectral and topographic coverages from a collection of overlapping digital imagery from consumer cameras. Cuneo Creek has had three historically observed episodes of rapid aggradation (1955, 1964, and 1997). The debris flow deposits continue to be major sources of sediment sixty years after the initial slope failure. Previous studies have monitored the sediment storage volume and particle size since 1976 (in 1976, 1982, 1983, 1985, 1986, 1987, 1998, 2003). We reoccupied 3 previously surveyed stream cross sections on Sept 30, 2014 and March 30, 2015, and produced photogrammetric point clouds using a pole mounted camera with a remote view finder to take nadir view images from 4.3 meters above the channel bed. Ground control points were registered using survey grade GPS and typical cross sections used over 100 images to build the structure model. This process simultaneously collects channel geometry and we used it to also generate surface texture metrics, and produced DEMs with point cloud densities above 5000 points / m2. In the period between the surveys, a five year recurrence interval discharge of 20 m3/s scoured the channel. Surface particle size distribution has been determined for each observation period using image segmentation algorithms based on spectral distance and compactness. Topographic differencing between the point clouds shows substantial channel bed mobilization and reorganization. The net decline in sediment storage is in excess of 4 x 10^5 cubic meters since the 1964 aggradation peak, with associated coarsening of surface particle sizes. These new methods provide a promising rapid assessment tool for measurement of channel responses to sediment inputs.

CoCr wear particles generated from CoCr alloy metal-on-metal hip replacements, and cobalt ions stimulate apoptosis and expression of general toxicology-related genes in monocyte-like U937 cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Posada, Olga M., E-mail: O.M.PosadaEstefan@leeds.ac.uk; Gilmour, Denise; Tate, Rothwelle J., E-mail: r.j.tate@strath.ac.uk

Cobalt-chromium (CoCr) particles in the nanometre size range and their concomitant release of Co and Cr ions into the patients' circulation are produced by wear at the articulating surfaces of metal-on-metal (MoM) implants. This process is associated with inflammation, bone loss and implant loosening and led to the withdrawal from the market of the DePuy ASR™ MoM hip replacements in 2010. Ions released from CoCr particles derived from a resurfacing implant in vitro and their subsequent cellular up-take were measured by ICP-MS. Moreover, the ability of such metal debris and Co ions to induce both apoptosis was evaluated with bothmore » FACS and immunoblotting. qRT-PCR was used to assess the effects on the expression of lymphotoxin alpha (LTA), BCL2-associated athanogene (BAG1), nitric oxide synthase 2 inducible (NOS2), FBJ murine osteosarcoma viral oncogene homolog (FOS), growth arrest and DNA-damage-inducible alpha (GADD45A). ICP-MS showed that the wear debris released significant (p < 0.05) amounts of Co and Cr ions into the culture medium, and significant (p < 0.05) cellular uptake of both ions. There was also an increase (p < 0.05) in apoptosis after a 48 h exposure to wear debris. Analysis of qRT-PCR results found significant up-regulation (p < 0.05) particularly of NOS2 and BAG1 in Co pre-treated cells which were subsequently exposed to Co ions + debris. Metal debris was more effective as an inducer of apoptosis and gene expression when cells had been pre-treated with Co ions. This suggests that if a patient receives sequential bilateral CoCr implants, the second implant may be more likely to produce adverse effects than the first one. - Highlights: • Effects of CoCr nanoparticles and Co ions on U937 cells were investigated. • Ions released from wear debris play an important role in cellular response, • Toxicity of Co ions could be related to NO metabolic processes and apoptosis. • CoCr particles were a more effective inducer of apoptosis after cell priming. • CoCr particles were a more effective inducer of gene expression after cell priming.« less

Millimeter Studies of Nearby Debris Disks

NASA Astrophysics Data System (ADS)

MacGregor, Meredith Ann

2017-03-01

At least 20% of nearby main sequence stars are known to be surrounded by disks of dusty material resulting from the collisional erosion of planetesimals, similar to asteroids and comets in our own Solar System. The material in these ‘debris disks’ is directly linked to the larger bodies, like planets, in the system through collisions and gravitational perturbations. Observations at millimeter wavelengths are especially critical to our understanding of these systems, since the large grains that dominate emission at these long wavelengths reliably trace the underlying planetesimal distribution. In this thesis, I have used state-of-the-art observations at millimeter wavelengths to address three related questions concerning debris disks and planetary system evolution: 1) How are wide-separation, substellar companions formed? 2) What is the physical nature of the collisional process in debris disks? And, 3) Can the structure and morphology of debris disks provide probes of planet formation and subsequent dynamical evolution? Using ALMA observations of GQ Lup, a pre-main sequence system with a wide-separation, substellar companion, I have placed constraints on the mass of a circumplanetary disk around the companion, informing formation scenarios for this and other similar systems (Chapter 2). I obtained observations of a sample of fifteen debris disks with both the VLA and ATCA at centimeter wavelengths, and robustly determined the millimeter spectral index of each disk and thus the slope of the grain size distribution, providing the first observational test of collision models of debris disks (Chapter 3). By applying an MCMC modeling framework to resolved millimeter observations with ALMA and SMA, I have placed the first constraints on the position, width, surface density gradient, and any asymmetric structure of the AU Mic, HD 15115, Epsilon Eridani, Tau Ceti, and Fomalhaut debris disks (Chapters 4–8). These observations of individual systems hint at trends in disk structure and dynamics, which can be explored further with a comparative study of a sample of the eight brightest debris disks around Sun-like stars within 20 pc (Chapter 9). This body of work has yielded the first resolved images of notable debris disks at millimeter wavelengths, and complements other ground- and space-based observations by providing constraints on these systems with uniquely high angular resolution and wavelength coverage. Together these results provide a foundation to investigate the dynamical evolution of planetary systems through multi-wavelength observations of debris disks.

Wildfire-induced initiation of debris flows in a steep bedrock landscape, San Gabriel Mountains, California

NASA Astrophysics Data System (ADS)

Ulizio, T. P.; Palucis, M. C.; Fuller, B. M.; Lamb, M. P.

2017-12-01

Steep, rocky landscapes often produce large sediment yields and increased debris flow activity following wildfire. There are two main hypotheses for debris flow initiation in burned regions during rain storms: (1) debris flows initiate from failure of the soil mantle on hillslopes where fire has destroyed root systems resulting in loss of soil strength, and (2) debris flows initiate in river channels that have been loaded by dry ravel following incineration of vegetation dams on hillslopes. To evaluate these hypotheses, we monitored a steep first-order catchment that burned in the 2016 Fish Canyon fire within the front range of the San Gabriel Mountains, CA. Following each post-fire storm, we measured the hillslope and channel topography using UAV imaging and structure-from-motion, and monitored activity during storm events with field cameras. Following the fire, but prior to the first storm event, most of the hillslopes were stripped to bedrock and 0.5 m of dry ravel had accumulated along the length of the channel. By using measurements of sediment storage behind vegetation in a nearby unburned catchment, but with a similar burn history, we found that much of the loose sediment in the channel can be attributed to dry ravel following incineration of vegetation dams. Throughout the rainy season, the catchment produced a series of debris flows that evacuated the accumulated dry ravel in the channel, exposed bedrock in the channel, and built a debris flow fan across a terrace that abuts the downstream end of the channel. Although later storms were larger, most sediment transport occurred during the first few storms, indicating that sediment supply can limit debris flow activity, and that larger storms do not necessarily produce larger debris flows. Our measurements of the volume of the newly formed debris flow fan approximately matches the volume of evacuated ravel from the channel, and we did not observe landslide scars on hillslopes. Together, these observations and mass-balance constraints support the model by which limited hillslope soil in steep rocky landscapes is destabilized as dry ravel following wildfire, leading to infilling of channels with relatively fine and loose sediment that subsequently fails, producing debris flows during rain storms.

Extensive Middle Amazonian mantling of debris aprons and plains in Deuteronilus Mensae, Mars: Implications for the record of mid-latitude glaciation

NASA Astrophysics Data System (ADS)

Baker, David M. H.; Head, James W.

2015-11-01

The mid-latitudes of Mars are host to a record of recent episodes of accumulations of ice-rich materials. The record includes debris aprons, interpreted to be debris-covered glaciers, that may represent the preserved remnants of a much more extensive ice sheet. We assessed the possibility of former glacial extents by examining debris aprons and the surrounding plains in Deuteronilus Mensae. Geomorphic units and stratigraphic relationships were mapped and documented from Mars Reconnaissance Orbiter (MRO) Context (CTX) and High Resolution Imaging Science Experiment (HiRISE) camera images, and crater retention ages were estimated from crater size-frequency distributions. Three major units are observed within the study area: debris aprons, lower plains, and upper plains. Debris aprons exhibit characteristics typical for these features documented elsewhere and in previous studies, including integrated flow lineations and patterns, convex-upward profiles, and knobby and brain terrain surface textures. A lower bound on the age for debris aprons is estimated to be 0.9 Ga. Debris aprons are superposed on a lower plains unit having a lower bound age of 3.3-3.5 Ga. A 50-100 m thick upper plains unit superposes both debris apron landforms and lower plains units and has a best-fit minimum age of 0.6 Ga. The upper plains unit exhibits characteristics of atmospherically-emplaced mantle material, including fine-grained nature, sublimation textures, cyclic layering, draping character, and widespread spatial distribution. Fracturing and subsequent sublimation/erosion of upper plains on debris aprons has contributed to many of the surface textures on debris aprons. The upper plains unit has also been eroded from the lower plains and plateaus, evidenced by isolated blocks of upper plains in the interiors of craters and on the walls and tops of plateaus. While no conclusive evidence diagnostic of former cold-based ice sheets are observed in the plains within the study region, such landforms and units may have been poorly developed or absent, as is often the case on Earth, and would have been covered and reworked by later mantling episodes. These observations suggest that emplacement of thick ice-rich mantle deposits extended at least to near the Early/Middle Amazonian boundary and overlapped with the waning stages of glaciation in Deuteronilus Mensae.

The role of orbital dynamics and cloud-cloud collisions in the formation of giant molecular clouds in global spiral structures

NASA Technical Reports Server (NTRS)

Roberts, William W., Jr.; Stewart, Glen R.

1987-01-01

The role of orbit crowding and cloud-cloud collisions in the formation of GMCs and their organization in global spiral structure is investigated. Both N-body simulations of the cloud system and a detailed analysis of individual particle orbits are used to develop a conceptual understanding of how individual clouds participate in the collective density response. Detailed comparisons are made between a representative cloud-particle simulation in which the cloud particles collide inelastically with one another and give birth to and subsequently interact with young star associations and stripped down simulations in which the cloud particles are allowed to follow ballistic orbits in the absence of cloud-cloud collisions or any star formation processes. Orbit crowding is then related to the behavior of individual particle trajectories in the galactic potential field. The conceptual picture of how GMCs are formed in the clumpy ISMs of spiral galaxies is formulated, and the results are compared in detail with those published by other authors.

An analysis of the 2016 Hitomi breakup event

NASA Astrophysics Data System (ADS)

Flegel, Sven; Bennett, James; Lachut, Michael; Möckel, Marek; Smith, Craig

2017-04-01

The breakup of Hitomi (ASTRO-H) on 26 March 2016 is analysed. Debris from the fragmentation is used to estimate the time of the event by propagating backwards and estimating the close approach with the parent object. Based on this method, the breakup event is predicted to have occurred at approximately 01:42 UTC on 26 March 2016. The Gaussian variation of parameters equations based on the instantaneous orbits at the predicted time of the event are solved to gain additional insight into the on-orbit position of Hitomi at the time of the event and to test an alternate approach of determining the event epoch and location. A conjunction analysis is carried out between Hitomi and all catalogued objects which were in orbit around the estimated time of the anomaly. Several debris objects have close approaches with Hitomi; however, there is no evidence to support the breakup was caused by a catalogued object. Debris from both of the largest fragmentation events—the Iridium 33-Cosmos 2251 conjunction in 2009 and the intentional destruction of Fengyun 1C in 2007—is involved in close approaches with Hitomi indicating the persistent threat these events have caused in subsequent space missions. To quantify the magnitude of a potential conjunction, the fragmentation resulting from a collision with the debris is modelled using the EVOLVE-4 breakup model. The debris characteristics are estimated from two-line element data. This analysis is indicative of the threat to space assets that mission planners face due to the growing debris population. The impact of the actual event to the environment is investigated based on the debris associated with Hitomi which is currently contained in the United States Strategic Command's catalogue. A look at the active missions in the orbital vicinity of Hitomi reveals that the Hubble Space Telescope is among the spacecraft which may be immediately affected by the new debris.[Figure not available: see fulltext.

IDE spatio-temporal impact fluxes and high time-resolution studies of multi-impact events and long-lived debris clouds

NASA Technical Reports Server (NTRS)

Mulholland, J. Derral; Singer, S. Fred; Oliver, John P.; Weinberg, Jerry L.; Cooke, William J.; Kassel, Philip C.; Wortman, Jim J.; Montague, Nancy L.; Kinard, William H.

1991-01-01

During the first 12 months of the Long Duration Exposure Facility (LDEF) mission, the Interplanetary Dust Experiment (IDE) recorded over 15,000 total impacts on six orthogonal faces with a time resolution on the order of 15 to 20 seconds. When combined with the orbital data and the stabilized configuration of the spacecraft, this permits a detailed analysis of the micro-particulate environment. The functional status of each of the 459 detectors was monitored every 2.4 hours, and post-flight analyses of these data has now permitted an evaluation of the effective active detection area as a function of time, panel by panel and separately for the two sensitivity levels. Thus, total impacts were transformed into areal fluxes, and are presented here for the first time. Also discussed are possible effects of these fluxes on previously announced results: apparent debris events, meteor stream detections, and beta meteoroids in observationally significant numbers.

Sarcoidosis diagnosed after September 11, 2001, among adults exposed to the World Trade Center disaster.

PubMed

Jordan, Hannah T; Stellman, Steven D; Prezant, David; Teirstein, Alvin; Osahan, Sukhminder S; Cone, James E

2011-09-01

Explore relationships between World Trade Center (WTC) exposures and sarcoidosis. Sarcoidosis has been reported after exposure to the WTC disaster. We ascertained biopsy-proven post-9/11 sarcoidosis among WTC Health Registry enrollees. Cases diagnosed after Registry enrollment were included in a nested case-control study. Controls were matched to cases on age, sex, race or ethnicity, and eligibility group (eg, rescue or recovery worker). We identified 43 cases of post-9/11 sarcoidosis. Twenty-eight incident cases and 109 controls were included in the case-control analysis. Working on the WTC debris pile was associated with sarcoidosis (odds ratio 9.1, 95% confidence interval 1.1 to 74.0), but WTC dust cloud exposure was not (odds ratio 1.0, 95% confidence interval 0.4 to 2.8). Working on the WTC debris pile was associated with an elevated risk of post-9/11 sarcoidosis. Occupationally exposed workers may be at increased risk. (C)2011The American College of Occupational and Environmental Medicine

Average Cross-Sectional Area of DebriSat Fragments Using Volumetrically Constructed 3D Representations

NASA Technical Reports Server (NTRS)

Scruggs, T.; Moraguez, M.; Patankar, K.; Fitz-Coy, N.; Liou, J.-C.; Sorge, M.; Huynh, T.

2016-01-01

Debris fragments from the hypervelocity impact testing of DebriSat are being collected and characterized for use in updating existing satellite breakup models. One of the key parameters utilized in these models is the ballistic coefficient of the fragment which is directly related to its area-to-mass ratio. However, since the attitude of fragments varies during their orbital lifetime, it is customary to use the average cross-sectional area in the calculation of the area-to-mass ratio. The average cross-sectional area is defined as the average of the projected surface areas perpendicular to the direction of motion and has been shown to be equal to one-fourth of the total surface area of a convex object. Unfortunately, numerous fragments obtained from the DebriSat experiment show significant concavity (i.e., shadowing) and thus we have explored alternate methods for computing the average cross-sectional area of the fragments. An imaging system based on the volumetric reconstruction of a 3D object from multiple 2D photographs of the object was developed for use in determining the size characteristic (i.e., characteristics length) of the DebriSat fragments. For each fragment, the imaging system generates N number of images from varied azimuth and elevation angles and processes them using a space-carving algorithm to construct a 3D point cloud of the fragment. This paper describes two approaches for calculating the average cross-sectional area of debris fragments based on the 3D imager. Approach A utilizes the constructed 3D object to generate equally distributed cross-sectional area projections and then averages them to determine the average cross-sectional area. Approach B utilizes a weighted average of the area of the 2D photographs to directly compute the average cross-sectional area. A comparison of the accuracy and computational needs of each approach is described as well as preliminary results of an analysis to determine the "optimal" number of images needed for the 3D imager to accurately measure the average cross sectional area of objects with known dimensions.

Analysis with SfM on-motion method of July 2015 extreme rainfall impacts on the S-charl valley road in the Canton of Graubünden, Switzerland

NASA Astrophysics Data System (ADS)

Voumard, Jérémie; Jaboyedoff, Michel

2016-04-01

The 22-23th July 2015, two severe storms at one day interval have caused in Scuol, lower Engadine (Canton of Graubünden, Switzerland). The static storm cells produced up to 150 mm rain precipitations in three hours generating several debris flow. On 22 July 2015, three buildings in the Pradella hamlet near Scuol were damaged by a debris flow. People of two holiday camps, 100 children and 40 adults, were evacuated. Nobody was injured but the buildings damages are important. A day after, about 200 mm rain in a short time were measured in the same area. A car was been swept away by a debris flow in the Scuol village and its driver could escape at the last moment. The S-charl valley was isolated during more than one week by seven big debris flows and several little ones. About 100 people, in majority holidaymakers, were blocked in the S-charl hamlet without power supply during few days. Until the swiss army built a provisional emergency bridge to open the valley access, the only way to access the S-charl valley was by helicopter. Overall damages -roads infrastructures, buildings, drinking water supply, power supply and other- are estimated to one million Swiss Francs and the debris flow volume is estimated to 100'00 cubic meters. The S-charl valley roadsides were photographed fifteen days before the extreme storm event from an on-motion vehicle. The same roadsides were photographed twenty days after the event with the same acquisition methodology. 3D point clouds from Structure of Motion (SfM) from the -before and after event- pictures have been produced and compared. Thus, is was possible to evaluate the number of debris flows that occurred in the S-charl valley and estimate their volume in the roadsides. This study case allows to evaluate the low-cost SfM on-motion methodology and to give theirs main advantages and disadvantages when it is used to estimate changes roadsides due to a natural hazard event.

An Attempt to Observe Debris from the Breakup of a Titan 3C-4 Transtage

NASA Technical Reports Server (NTRS)

Barker, E. S.; Matney, M. J.; Yanagisawa, T.; Liou, J.-C.; Abercromby, K. J.; Rodriquez, H. M.; Horstman, M. F.; Seitzer, P.

2007-01-01

In February 2007 dedicated observations were made of the orbital space predicted to contain debris from the breakup of the Titan 3C-4 transtage back on February 21, 1992. These observations were carried out on the Michigan Orbital DEbris Survey Telescope (MODEST) in Chile with its 1.3deg field of view. The search region or orbital space (inclination and right ascension of the ascending node (RAAN) was predicted using NASA#s LEGEND (LEO-to-GEO Environment Debris) code to generate a Titan debris cloud. Breakup fragments are created based on the NASA Standard Breakup Model (including fragment size, area-to-mass (A/M), and delta-V distributions). Once fragments are created, they are propagated forward in time with a subroutine GEOPROP. Perturbations included in GEOPROP are those due to solar/lunar gravity, radiation pressure, and major geopotential terms. Barker, et. al, (AMOS Conference Proceedings, 2006, pp. 596-604) used similar LEGEND predictions to correlate survey observations made by MODEST (February 2002) and found several possible night-to-night correlations in the limited survey dataset. One conc lusion of the survey search was to dedicate a MODEST run to observing a GEO region predicted to contain debris fragments and actual Titan debris objects (SSN 25000, 25001 and 30000). Such a dedicated run was undertaken with MODEST between February 17 and 23, 2007 (UT dates). MODEST#s limiting magnitude of 18.0 (S\\N approx.10) corresponds to a size of 22cm assuming a diffuse Lambertian albedo of 0.2. However, based on observed break-up data, we expect most debris fragments to be smaller than 22cm which implies a need to increase the effective sensitivity of MODEST for smaller objects. MODEST#s limiting size can be lowered by increasing the exposure time (20 instead of 5 seconds) and applying special image processing. The special processing combines individual CCD images to detect faint objects that are invisible on a single CCD image. Sub-images are cropped from six consecutive CCD images with pixel shifts between images being consistent with the predicted movement of a Titan object. A median image of all the sub-images is then created leaving only those objects with the proper Titan motion. Limiting the median image in this manner brings the needed computer time to process all images taken on one night down to about 50 hours of CPU time.

Theoretical study of mixing in liquid clouds – Part 1: Classical concepts

DOE PAGES

Korolev, Alexei; Khain, Alex; Pinsky, Mark; ...

2016-07-28

The present study considers final stages of in-cloud mixing in the framework of classical concept of homogeneous and extreme inhomogeneous mixing. Simple analytical relationships between basic microphysical parameters were obtained for homogeneous and extreme inhomogeneous mixing based on the adiabatic consideration. It was demonstrated that during homogeneous mixing the functional relationships between the moments of the droplets size distribution hold only during the primary stage of mixing. Subsequent random mixing between already mixed parcels and undiluted cloud parcels breaks these relationships. However, during extreme inhomogeneous mixing the functional relationships between the microphysical parameters hold both for primary and subsequent mixing.more » The obtained relationships can be used to identify the type of mixing from in situ observations. The effectiveness of the developed method was demonstrated using in situ data collected in convective clouds. It was found that for the specific set of in situ measurements the interaction between cloudy and entrained environments was dominated by extreme inhomogeneous mixing.« less

Experimental Exploration on Rainfall-induced Mass Re-mobilization after Giant Earthquake: A case study in Wenchuan earthquake hit region, China

NASA Astrophysics Data System (ADS)

Yang, Zongji; Bogaard, Thom. A.; Qiao, Jianping; Jiang, Yuanjun

2015-04-01

Prevention and mitigation of rainfall induced geological hazards after the Ms=8 Wenchuan earthquake on May 12th, 2008 were gained more significance for the rebuild of earthquake hit regions in China. After the Wenchuan earthquake, there were thousands of slopes failure, which were much more susceptible to subsequent heavy rainfall and many even transformed into potential debris flows. An typical example can be found in the catastrophic disaster occurred in Zhongxing County, Chengdu City on 10th July, 2013 in which the unknown fractured slope up the mountain was triggered by a downpour and transformed into subsequent debris flow which wiped the community downstream, about 200 victims were reported in that tragic event. The transform patterns of rainfall-induced mass re-mobilization was categorized into three major type as the erosion of fractured slopes, initiate on loosen deposit and outbreak of landslide (debris flow) dams according to vast field investigation in the earthquake hit region. Despite the widespread and hidden characters,the complexity of the process also demonstrated in the transforms of the mass re-mobilized by the erosion of both gravity and streams in the small watersheds which have never been reported before the giant Wenchuan Earthquake in many regions. As a result, an increasing number of questions for disaster relief and mitigation were proposed including the threshold of early warning and measurement of the volume for the design of mitigation measures on rainfall-induced mass re-mobilization in debris flow gullies. This study is aimed for answer the essential questions about the threshold and amount of mass initiation triggered by the subsequent rainfall in post earthquake time. In this study, experimental tests were carried out for simulating the failure of the rainfall-induced mass re-mobilization in respectively in a natural co-seismic fractured slope outside and the debris flow simulation platform inside the laboratory. A natural fractured slope was selected to conduct the field experimental test,after the field experimental test, the correlation of rainfall parameters, deformation criterion and water content as well as the failure volume of gravity erosion was investigated. In addition, the loosen mass re-mobilized by the stream was also simulated by the model experiment by which the correlation of rainfall thresholds, and the initial volume of mass triggered by the flow was analyzed. Thus, the threshold and volume measurement model for the initiation of mass re-mobilization were proposed by means of this experimental research. Despite of the fact that the simplicity of the model derived from experimental and empirical method and some drawbacks connected with the uncertainty and complexity of the geological phenomenon, the proposed method have contributed a lot in application for the early warning and prevention of mass transformed debris flows in earthquake hit region, China.

Millimeter Studies of Nearby Debris Disks

NASA Astrophysics Data System (ADS)

MacGregor, Meredith A.

2017-01-01

At least 20% of nearby main sequence stars are known to be surrounded by disks of dusty material resulting from the collisional erosion of planetesimals, larger bodies similar to asteroids and comets in our own Solar System. Since the dust-producing planetesimals are expected to persist in stable regions like belts and resonances, the locations, morphologies, and physical properties of dust in these ‘debris disks’ provide probes of planet formation and subsequent dynamical evolution. Observations at millimeter wavelengths are especially critical to our understanding of these systems, since the large grains that dominate emission at these long wavelengths do not travel far from their origin and therefore reliably trace the underlying planetesimal distribution. The newly upgraded capabilities of millimeter interferometers like ALMA are providing us with the opportunity to image these disks with unprecedented sensitivity and resolution. In this dissertation talk, I will present my ongoing work, which uses observations of the angularly resolved brightness distribution and the spectral dependence of the flux density to constrain both the structure and grain size distribution of a sample of nearby debris disks. I will present constraints on the position, width, surface density gradient, and any asymmetric structure of several debris disks (including Epsilon Eridani, Tau Ceti, and Fomalhaut) determined from ALMA and SMA observations. In addition, I will present the results of a survey using the VLA and ATCA to measure the long wavelength spectral index and thus the grain size distribution of fifteen debris disks. Together these results provide a foundation to investigate the dynamical evolution of planetary systems through multi-wavelength observations of debris disks.

The Role of Materials Degradation and Analysis in the Space Shuttle Columbia Accident Investigation

NASA Technical Reports Server (NTRS)

McDanels, Steven J.

2006-01-01

The efforts following the loss of the Space Shuttle Columbia included debris recovery, reconstruction, and analysis. The debris was subjected to myriad quantitative and semiquantitative chemical analysis techniques, ranging from examination via the scanning electron microscope (SEM) with energy dispersive spectrometer (EDS) to X-Ray diffraction (XRD) and electron probe micro-analysis (EPMA). The results from the work with the debris helped the investigators determine the location where a breach likely occurred in the leading edge of the left wing during lift off of the Orbiter from the Kennedy Space Center. Likewise, the information evidenced by the debris was also crucial in ascertaining the path of impinging plasma flow once it had breached the wing. After the Columbia Accident Investigation Board (CAIB) issued its findings, the major portion of the investigation was concluded. However, additional work remained to be done on many pieces of debris from portions of the Orbiter which were not directly related to the initial impact during ascent. This subsequent work was not only performed in the laboratory, but was also performed with portable equipment, including examination via portable X-Ray fluorescence (XRF) and Fourier transform infrared spectroscopy (FTIR). Likewise, acetate and silicon-rubber replicas of various fracture surfaces were obtained for later macroscopic and fractographic examination. This paper will detail the efforts and findings from the initial investigation, as well as present results obtained by the later examination and analysis of debris from the Orbiter including its windows, bulkhead structures, and other components which had not been examined during the primary investigation.

Ingested microscopic plastic translocates to the circulatory system of the mussel, Mytilus edulis (L).

PubMed

Browne, Mark A; Dissanayake, Awantha; Galloway, Tamara S; Lowe, David M; Thompson, Richard C

2008-07-01

Plastics debris is accumulating in the environment and is fragmenting into smaller pieces; as it does, the potential for ingestion by animals increases. The consequences of macroplastic debris for wildlife are well documented, however the impacts of microplastic (< 1 mm) are poorly understood. The mussel, Mytilus edulis, was used to investigate ingestion, translocation, and accumulation of this debris. Initial experiments showed that upon ingestion, microplastic accumulated in the gut. Mussels were subsequently exposed to treatments containing seawater and microplastic (3.0 or 9.6 microm). After transfer to clean conditions, microplastic was tracked in the hemolymph. Particles translocated from the gut to the circulatory system within 3 days and persisted for over 48 days. Abundance of microplastic was greatest after 12 days and declined thereafter. Smaller particles were more abundant than larger particles and our data indicate as plastic fragments into smaller particles, the potential for accumulation in the tissues of an organism increases. The short-term pulse exposure used here did not result in significant biological effects. However, plastics are exceedingly durable and so further work using a wider range of organisms, polymers, and periods of exposure will be required to establish the biological consequences of this debris.

Electric field measuring and display system. [for cloud formations

NASA Technical Reports Server (NTRS)

Wojtasinski, R. J.; Lovall, D. D. (Inventor)

1974-01-01

An apparatus is described for monitoring the electric fields of cloud formations within a particular area. It utilizes capacitor plates that are alternately shielded from the clouds for generating an alternating signal corresponding to the intensity of the electric field of the clouds. A synchronizing signal is produced for controlling sampling of the alternating signal. Such samplings are fed through a filter and converted by an analogue to digital converter into digital form and subsequently fed to a transmitter for transmission to the control station for recording.

Do Clouds Save the Great Barrier Reef? Satellite Imagery Elucidates the Cloud-SST Relationship at the Local Scale

PubMed Central

Leahy, Susannah M.; Kingsford, Michael J.; Steinberg, Craig R.

2013-01-01

Evidence of global climate change and rising sea surface temperatures (SSTs) is now well documented in the scientific literature. With corals already living close to their thermal maxima, increases in SSTs are of great concern for the survival of coral reefs. Cloud feedback processes may have the potential to constrain SSTs, serving to enforce an “ocean thermostat” and promoting the survival of coral reefs. In this study, it was hypothesized that cloud cover can affect summer SSTs in the tropics. Detailed direct and lagged relationships between cloud cover and SST across the central Great Barrier Reef (GBR) shelf were investigated using data from satellite imagery and in situ temperature and light loggers during two relatively hot summers (2005 and 2006) and two relatively cool summers (2007 and 2008). Across all study summers and shelf positions, SSTs exhibited distinct drops during periods of high cloud cover, and conversely, SST increases during periods of low cloud cover, with a three-day temporal lag between a change in cloud cover and a subsequent change in SST. Cloud cover alone was responsible for up to 32.1% of the variation in SSTs three days later. The relationship was strongest in both El Niño (2005) and La Niña (2008) study summers and at the inner-shelf position in those summers. SST effects on subsequent cloud cover were weaker and more variable among study summers, with rising SSTs explaining up to 21.6% of the increase in cloud cover three days later. This work quantifies the often observed cloud cooling effect on coral reefs. It highlights the importance of incorporating local-scale processes into bleaching forecasting models, and encourages the use of remote sensing imagery to value-add to coral bleaching field studies and to more accurately predict risks to coral reefs. PMID:23894649

Time-series analysis on bed morphology affected by debris flows along a headwater steep channel in Ohya-kuzure landslide, central Japan

NASA Astrophysics Data System (ADS)

Hayakawa, Y. S.; Imaizumi, F.; Hotta, N.; Tsunetaka, H.

2013-12-01

Deformation of steep terrain has been occurring since the formation of Ohyakuzure landslide in 1707. Although erosion controls in recent decades have resulted in vegetation recovery in downstream portions of the landslide terrain, hillslope erosion and debris flows frequently occur in uppermost steep subwatersheds in the landslide area to yield vast amount of sediment downstream. Ichino-sawa subwatershed in the landslide terrain, where detailed monitoring of debris flows and related topographic changes have previously been performed, has particularly steep slopes, and geomorphic processes therein have been quite active. Freeze-thaw weathering of fractured bedrock on hillslopes made of shale and sandstone frequently occurs in winter to spring season, and resultant sediment particles are provided into channel beds, which act as a source of debris flows that frequently occurs in summer season with heavy or accumulated rainfalls. High-resolution assessment of erosion/deposition patterns in channel bed of the Ichinosawa catchment was performed using multi-temporal terrestrial laser scanning data covering 3 seasons for 2 years. Seasonal changes in spatial distribution of erosion and deposition in the channel bed is quantified using a 0.1-m DEM converted from the original point cloud by TLS. The multi-temporal datasets provides an estimate of annual sediment storage and yield on the order of 1,000 - 5,000 m3. Analysis of changes in elevation by transverse and longitudinal profiles shows contrasting patterns of erosion and deposition along the studied reach: in particular, changes in bed elevation is found to be less in a 50-m long reach, whose downstream part seems bounded by valley narrowing and a knickpoint. Several topographic metrics, including stream gradient, surface roughness and topographic openness, were examined to estimate the characteristics of differing transport processes induced by debris flows along the reaches.

Long-term microparticle flux variability indicated by comparison of Interplanetary Dust Experiment (IDE) timed impacts for LDEF's first year in orbit with impact data for the entire 5.77-year orbital lifetime

NASA Technical Reports Server (NTRS)

Simon, Charles G.; Mulholland, J. Derral; Oliver, John P.; Cooke, William J.; Kassel, Philip C., Jr.

1993-01-01

The electronic sensors of the Interplanetary Dust Experiment (IDE) recorded precise impact times and approximate directions for submicron to approximately 100 micron size particles on all six primary sides of the spacecraft for the first 346 days of the LDEF orbital mission. Previously-reported analyses of the timed impact data have established their spatio-temporal features, including the demonstration that a preponderance of the particles in this regime are orbital debris and that a large fraction of the debris particles are encountered in megameter-size clouds. Short-term fluxes within such clouds can rise several orders of magnitude above the long-term average. These unexpectedly large short-term variations in debris flux raise the question of how representative an indication of the multi-year average flux is given by the nearly one year of timed data. One of the goals of the IDE was to conduct an optical survey of impact sites on detectors that remained active during the entire LDEF mission, to obtain full-mission fluxes. We present here the comparisons and contrasts among the new IDE optical survey impact data, the IDE first-year timed impact data, and impact data from other LDEF micrometeoroid and debris experiments. The following observations are reported: (1) the 5.77 year long-term integrated microparticle impact fluxes recorded by IDE detectors matched the integrated impact fluxes measured by other LDEF investigators for the same period; (2) IDE integrated microparticle impact fluxes varied by factors from 0.5 to 8.3 for LDEF days 1-346, 347-2106 and 1-2106 (5.77 years) on rows 3 (trailing edge, or West), 6 (South side), 12 (North side), and the Earth and Space ends; and (3) IDE integrated microparticle impact fluxes varied less than 3 percent for LDEF days 1-346, 347-2106 and 1-2106 (5.77 years) on row 9 (leading edge, or East). These results give further evidence of the accuracy and internal consistency of the recorded IDE impact data. This leads to the further conclusion that the utility of long-term ratios for impacts on various sides of a stabilized satellite in low Earth orbit (LEO) is extremely limited. These observations and their consequences highlight the need for continuous, real time monitoring of the dynamic microparticle environment in LEO.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fan, Jiwen; Rosenfeld, Daniel; Zhang, Yuwei

Aerosol-cloud interactions remain the largest uncertainty in climate projections. Ultrafine aerosol particles smaller than 50 nanometers (UAP <50) can be abundant in the troposphere, but are conventionally considered too small to affect cloud formation. However, observational evidence and numerical simulations of deep convective clouds (DCCs) over the Amazon show that DCCs forming in a low aerosol environment can develop very large vapor supersaturation because fast droplet coalescence reduces integrated droplet surface area and subsequent condensation. UAP <50 from pollution plumes that are ingested into such clouds can be activated to form additional cloud droplets on which excess supersaturation condenses andmore » forms additional cloud water and latent heating, thus intensifying convective strength. This mechanism suggests a strong anthropogenic invigoration of DCCs in previously pristine regions of the world.« less

Long-term Evolution of the Aerosol Debris Cloud Produced by the 2009 Impact of an Object with Jupiter

NASA Astrophysics Data System (ADS)

Sanchez-Lavega, Agustin; Orton, G. S.; Hueso, R.; Pérez-Hoyos, S.; Fletcher, L. N.; Garcia-Melendo, E.; Gomez, J. M.; de Pater, I.; Wong, M.; Hammel, H. B.; Yanamandra-Fisher, P.; Simon-Miller, M.; Barrado-Izagirre, N.; Marchis, F.; Mousis, O.; Ortiz, J. L.; Garcia, J.; Cecconi, M.; Clarke, J. T.; Noll, K.; Pedraz, S.; Wesley, A.; McConnel, N.; Kalas, P.; Graham, J.; McKenzie, L.; Reddy, V.; Golisch, W.; Griep, D.; Sears, P.; International Outer PLanet Watch (IOPW)

2010-10-01

We report the evolution of the cloud of aerosols produced in the atmosphere of Jupiter by the impact of an object in 19 July 2009 (Sánchez-Lavega et al., Astrophys. J. Lett, Vol. 715, L155. 2010). This study is based on images obtained with a battery of ground-based telescopes and the Hubble Space Telescope in the visible and in the deep near infrared absorption bands at 2.1-2.3 microns from the impact date to 31 December 2009. The impact cloud expanded zonally from 5000 km (July 19) to 225,000 km (about 180 deg in longitude by 29 October) and it was meridionally localized within a latitude band from -53.5 deg to -61.5 deg. During the first two months it showed a heterogeneous structure with embedded spots of a size of 500 - 1000 km. The cloud was mainly dispersed in longitude by the dominant zonal winds and their meridional shear and, during the initial stages, by the action of local motions perhaps originated by the thermal perturbation produced at the impact site. The tracking of individual spots within the impact cloud showed that the winds increase their eastward velocity with altitude above the tropopause by 5-10 m/s. We found evidence of discrete localized meridional motions in the equatorward direction with speeds of 1 - 2 m/s. Measurements of the cloud reflectivity evolution during the whole period showed that it followed an exponential decrease with a characteristic time of 15 days, shorter than the 45 - 200 days sedimentation time for the small aerosol particles in the stratosphere. A radiative transfer model of the cloud optical depth coupled to an advection model of the cloud dispersion by the wind shears, reproduces this behavior. Acknowledgements: ASL, RH, SPH, NBI are supported by the Spanish MICIIN AYA2009-10701 with FEDER and Grupos Gobierno Vasco IT-464-07.

A multidisciplinary effort to assign realistic source parameters to models of volcanic ash-cloud transport and dispersion during eruptions

USGS Publications Warehouse

Mastin, Larry G.; Guffanti, Marianne C.; Servranckx, R.; Webley, P.; Barsotti, S.; Dean, K.; Durant, A.; Ewert, John W.; Neri, A.; Rose, W.I.; Schneider, David J.; Siebert, L.; Stunder, B.; Swanson, G.; Tupper, A.; Volentik, A.; Waythomas, Christopher F.

2009-01-01

During volcanic eruptions, volcanic ash transport and dispersion models (VATDs) are used to forecast the location and movement of ash clouds over hours to days in order to define hazards to aircraft and to communities downwind. Those models use input parameters, called “eruption source parameters”, such as plume height H, mass eruption rate Ṁ, duration D, and the mass fraction m63 of erupted debris finer than about 4ϕ or 63 μm, which can remain in the cloud for many hours or days. Observational constraints on the value of such parameters are frequently unavailable in the first minutes or hours after an eruption is detected. Moreover, observed plume height may change during an eruption, requiring rapid assignment of new parameters. This paper reports on a group effort to improve the accuracy of source parameters used by VATDs in the early hours of an eruption. We do so by first compiling a list of eruptions for which these parameters are well constrained, and then using these data to review and update previously studied parameter relationships. We find that the existing scatter in plots of H versus Ṁ yields an uncertainty within the 50% confidence interval of plus or minus a factor of four in eruption rate for a given plume height. This scatter is not clearly attributable to biases in measurement techniques or to well-recognized processes such as elutriation from pyroclastic flows. Sparse data on total grain-size distribution suggest that the mass fraction of fine debris m63 could vary by nearly two orders of magnitude between small basaltic eruptions (∼ 0.01) and large silicic ones (> 0.5). We classify eleven eruption types; four types each for different sizes of silicic and mafic eruptions; submarine eruptions; “brief” or Vulcanian eruptions; and eruptions that generate co-ignimbrite or co-pyroclastic flow plumes. For each eruption type we assign source parameters. We then assign a characteristic eruption type to each of the world's ∼ 1500 Holocene volcanoes. These eruption types and associated parameters can be used for ash-cloud modeling in the event of an eruption, when no observational constraints on these parameters are available.

Determine precipitation rates from visible and infrared satellite images of clouds by pattern recognition technique. Progress Report, 1 Jul. 1985 - 31 Mar. 1987 Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Weinman, James A.; Garan, Louis

1987-01-01

A more advanced cloud pattern analysis algorithm was subsequently developed to take the shape and brightness of the various clouds into account in a manner that is more consistent with the human analyst's perception of GOES cloud imagery. The results of that classification scheme were compared with precipitation probabilities observed from ships of opportunity off the U.S. east coast to derive empirical regressions between cloud types and precipitation probability. The cloud morphology was then quantitatively and objectively used to map precipitation probabilities during two winter months during which severe cold air outbreaks were observed over the northwest Atlantic. Precipitation probabilities associated with various cloud types are summarized. Maps of precipitation probability derived from the cloud morphology analysis program for two months and the precipitation probability derived from thirty years of ship observation were observed.

Factors Influencing Cloud-Computing Technology Adoption in Developing Countries

ERIC Educational Resources Information Center

Hailu, Alemayehu

2012-01-01

Adoption of new technology has complicating components both from the selection, as well as decision-making criteria and process. Although new technology such as cloud computing provides great benefits especially to the developing countries, it has challenges that may complicate the selection decision and subsequent adoption process. This study…

Habitability in different Milky Way stellar environments: a stellar interaction dynamical approach.

PubMed

Jiménez-Torres, Juan J; Pichardo, Bárbara; Lake, George; Segura, Antígona

2013-05-01

Every Galactic environment is characterized by a stellar density and a velocity dispersion. With this information from literature, we simulated flyby encounters for several Galactic regions, numerically calculating stellar trajectories as well as orbits for particles in disks; our aim was to understand the effect of typical stellar flybys on planetary (debris) disks in the Milky Way Galaxy. For the solar neighborhood, we examined nearby stars with known distance, proper motions, and radial velocities. We found occurrence of a disturbing impact to the solar planetary disk within the next 8 Myr to be highly unlikely; perturbations to the Oort cloud seem unlikely as well. Current knowledge of the full phase space of stars in the solar neighborhood, however, is rather poor; thus we cannot rule out the existence of a star that is more likely to approach than those for which we have complete kinematic information. We studied the effect of stellar encounters on planetary orbits within the habitable zones of stars in more crowded stellar environments, such as stellar clusters. We found that in open clusters habitable zones are not readily disrupted; this is true if they evaporate in less than 10(8) yr. For older clusters the results may not be the same. We specifically studied the case of Messier 67, one of the oldest open clusters known, and show the effect of this environment on debris disks. We also considered the conditions in globular clusters, the Galactic nucleus, and the Galactic bulge-bar. We calculated the probability of whether Oort clouds exist in these Galactic environments.

The Impact of a Large Object with Jupiter in July 2009

NASA Astrophysics Data System (ADS)

Sanchez-Lavega, Agustin; Wesley, A.; Orton, G.; Chodas, P.; Hueso, R.; Perez-Hoyos, S.; Fletcher, L.; Yanamandra-Fisher, P.; Legarreta, J.; Gomez-Forrellad, J. M.

2010-05-01

The only major impact ever observed directly in the Solar System was that of a large fragmented comet with Jupiter in July (1994) (Comet Shoemaker-Levy 9; SL9). We report here the observation of a second, single, large impact on Jupiter that occurred on 19 July 2009 at a latitude of -55° with an orthogonal entry trajectory and a lower incidence angle compared to those of SL9. The size of the initial aerosol cloud debris was 4,800 km East-West and 2,500 km North-South. Comparison its properties with those produced by the SL9 fragments, coupled with dynamical calculations of possible pre-impact orbits, indicates that the impactor was most probably an icy body with a size of 0.5-1 km. We calculate that the rate of collisions of this magnitude may be five to ten times more frequent than previously thought. The search for unpredicted impacts, such as the current one, could be best performed in the near-infrared methane absorption bands at 890 nm and in the 2.12 to 2.3 μm K methane-hydrogen absorption band, where the high-altitude aerosols detach by their brightness relative to Jupiter's primary clouds. We present measurements of the debris dispersion by Jovian winds from a long-term imaging campaign with ground-based telescopes. Ackowledgements: Work was supported by the Spanish MICIIN AYA2009-10701 with FEDER and Grupos Gobierno Vasco IT-464-07, by NASA funds to JPL, Caltech, by the NASA Postdoctoral Program at JPL, and by the Glasstone Fellowship program at Oxford.

Cluster beam targets for laser plasma extreme ultraviolet and soft x-ray sources

DOEpatents

Kublak, G.D.; Richardson, M.C.

1996-11-19

Method and apparatus for producing extreme ultraviolet (EUV) and soft x-ray radiation from an ultra-low debris plasma source are disclosed. Targets are produced by the free jet expansion of various gases through a temperature controlled nozzle to form molecular clusters. These target clusters are subsequently irradiated with commercially available lasers of moderate intensity (10{sup 11}--10{sup 12} watts/cm{sup 2}) to produce a plasma radiating in the region of 0.5 to 100 nanometers. By appropriate adjustment of the experimental conditions the laser focus can be moved 10--30 mm from the nozzle thereby eliminating debris produced by plasma erosion of the nozzle. 5 figs.

Cluster beam targets for laser plasma extreme ultraviolet and soft x-ray sources

DOEpatents

Kublak, Glenn D.; Richardson, Martin C. (CREOL

1996-01-01

Method and apparatus for producing extreme ultra violet (EUV) and soft x-ray radiation from an ultra-low debris plasma source are disclosed. Targets are produced by the free jet expansion of various gases through a temperature controlled nozzle to form molecular clusters. These target clusters are subsequently irradiated with commercially available lasers of moderate intensity (10.sup.11 -10.sup.12 watts/cm.sup.2) to produce a plasma radiating in the region of 0.5 to 100 nanometers. By appropriate adjustment of the experimental conditions the laser focus can be moved 10-30 mm from the nozzle thereby eliminating debris produced by plasma erosion of the nozzle.

Plant Succession on the Mount St. Helen's Debris-Avalanche Deposit and the Role of Non-native Species

DOE Office of Scientific and Technical Information (OSTI.GOV)

Denton, Elsie M.; Dale, Virginia H.

The abstract is published online only. If you did not include a short abstract for the online version when you submitted the manuscript, the first paragraph or the first 10 lines of the chapter will be displayed here. If possible, please provide us with an informative abstract. The debris-avalanche deposit is one of the most disturbed areas created by the 1980 eruption of Mount St. Helens, with little survival of a few plant fragments and primary succession mostly being initiated by the seeds dispersed onto the newly emplaced material. Vegetation changes on the debris-avalanche deposit during the first 30 yearsmore » post eruption are analyzed considering the role of non-native species and potential future vegetation patterns on the deposit. We found that the aerial distribution of largely non-native seeds on a subset of plots at Mount St. Helens in 1980 has had a pronounced and enduring effect on subsequent vegetation communities.« less

Mechanical contact induced transformation from the amorphous to the crystalline state in metallic glass

NASA Technical Reports Server (NTRS)

Miyoshi, K.; Buckley, D. H.

1984-01-01

Friction and wear tests were conducted with 3.2- and 6.4-millimeter-diameter aluminum oxide spheres sliding, in reciprocating motion, on a Fe67Co18B14Si1 metallic foil. Crystallites with a size range of 10 to 150 nanometers were produced on the wear surface of the amorphous alloy. A strong interaction between transition metals and metalloids such as silicon and boron results in strong segregation during repeated sliding, provides preferential transition metal-metalloid clustering in the amorphous alloy, and subsequently produces the diffused honeycomb structure formed by dark grey bands and primary crystals, that is, alpha-Fe in the matrix. Large plastic flow occurs on an amorphous alloy surface with sliding and the flow film of the alloy transfers to the aluminum oxide pin surface. Multiple slip bands due to shear deformation are observed on the side of the wear track. Two distinct types of wear debris were observed as a result of sliding: an alloy wear debris, and/or powdery-whiskery oxide debris.

Ingestion and fragmentation of plastic carrier bags by the amphipod Orchestia gammarellus: Effects of plastic type and fouling load.

PubMed

Hodgson, D J; Bréchon, A L; Thompson, R C

2018-02-01

Inappropriate disposal of plastic debris has led to the contamination of marine habitats worldwide. This debris can be ingested by organisms; however, the extent to which chewing and gut transit modifies plastic debris is unclear. Detritivores, such as amphipods, ingest and shred natural organic matter and are fundamental to its breakdown. Here we examine ingestion and shredding of plastic carrier bags by Orchestia gammarellus. A laboratory experiment showed these amphipods shredded plastic carrier bags, generating numerous microplastic fragments (average diameter 488.59μm). The presence of a biofilm significantly increased the amount of shredding, but plastic type (conventional, degradable and biodegradable) had no effect. Subsequent field observations confirmed similar shredding occurred on the strandline. Rates of shredding will vary according to amphipod density; however, our data indicates that shredding by organisms could substantially accelerate the formation microplastics in the environment. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

STEP-TRAMM - A modeling interface for simulating localized rainfall induced shallow landslides and debris flow runout pathways

NASA Astrophysics Data System (ADS)

Or, D.; von Ruette, J.; Lehmann, P.

2017-12-01

Landslides and subsequent debris-flows initiated by rainfall represent a common natural hazard in mountainous regions. We integrated a landslide hydro-mechanical triggering model with a simple model for debris flow runout pathways and developed a graphical user interface (GUI) to represent these natural hazards at catchment scale at any location. The STEP-TRAMM GUI provides process-based estimates of the initiation locations and sizes of landslides patterns based on digital elevation models (SRTM) linked with high resolution global soil maps (SoilGrids 250 m resolution) and satellite based information on rainfall statistics for the selected region. In the preprocessing phase the STEP-TRAMM model estimates soil depth distribution to supplement other soil information for delineating key hydrological and mechanical properties relevant to representing local soil failure. We will illustrate this publicly available GUI and modeling platform to simulate effects of deforestation on landslide hazards in several regions and compare model outcome with satellite based information.

High Contrast Imaging of Exoplanets and Exoplanetary Systems with JWST

NASA Astrophysics Data System (ADS)

Hinkley, Sasha; Skemer, Andrew; Biller, Beth; Baraffe, I.; Bonnefoy, M.; Bowler, B.; Carter, A.; Chen, C.; Choquet, E.; Currie, T.; Danielski, C.; Fortney, J.; Grady, C.; Greenbaum, A.; Hines, D.; Janson, M.; Kalas, P.; Kennedy, G.; Kraus, A.; Lagrange, A.; Liu, M.; Marley, M.; Marois, C.; Matthews, B.; Mawet, D.; Metchev, S.; Meyer, M.; Millar-Blanchaer, M.; Perrin, M.; Pueyo, L.; Quanz, S.; Rameau, J.; Rodigas, T.; Sallum, S.; Sargent, B.; Schlieder, J.; Schneider, G.; Stapelfeldt, K.; Tremblin, P.; Vigan, A.; Ygouf, M.

2017-11-01

JWST will transform our ability to characterize directly imaged planets and circumstellar debris disks, including the first spectroscopic characterization of directly imaged exoplanets at wavelengths beyond 5 microns, providing a powerful diagnostic of cloud particle properties, atmospheric structure, and composition. To lay the groundwork for these science goals, we propose a 39-hour ERS program to rapidly establish optimal strategies for JWST high contrast imaging. We will acquire: a) coronagraphic imaging of a newly discovered exoplanet companion, and a well-studied circumstellar debris disk with NIRCam & MIRI; b) spectroscopy of a wide separation planetary mass companion with NIRSPEC & MIRI; and c) deep aperture masking interferometry with NIRISS. Our primary goals are to: 1) generate representative datasets in modes to be commonly used by the exoplanet and disk imaging communities; 2) deliver science enabling products to empower a broad user base to develop successful future investigations; and 3) carry out breakthrough science by characterizing exoplanets for the first time over their full spectral range from 2-28 microns, and debris disk spectrophotometry out to 15 microns sampling the 3 micron water ice feature. Our team represents the majority of the community dedicated to exoplanet and disk imaging and has decades of experience with high contrast imaging algorithms and pipelines. We have developed a collaboration management plan and several organized working groups to ensure we can rapidly and effectively deliver high quality Science Enabling Products to the community.

Unmelted meteoritic debris in the Late Pliocene iridium anomaly - Evidence for the ocean impact of a nonchondritic asteroid

NASA Technical Reports Server (NTRS)

Kyte, F. T.; Brownlee, D. E.

1985-01-01

Ir-bearing particles have been recovered from two piston cores in the Antarctic Basin in the southeastern Pacific. In core E13-3, the particles closely correspond to the Late Pliocene Ir anomaly and have a fluence of about 100 mg/cm sq. In core E13-4, 120 km to the southwest, the particle fluence is about 4 mg/cm sq. Particles with diameters from 0.5 to 4 mm contain at least 35 percent of the Ir in this horizon. Three types of particles have been identified: (1) vesicular, (2) basaltic, and (3) metal. The vesicular particles appear to be shock-melted debris derived from the oceanic impact of a howarditic asteroid containing a minor metal component. These particles have recrystallized from a melt and impact into the ocean has resulted in the incorporation of Na, K, Cl, and radiogenic Sr from the ocean water target. The basaltic clasts appear to be unmelted fragments of the original asteroid which may have separated from the main body prior to impact. Combined vesicular and basaltic particles are believed to have formed by collisions in the debris cloud. Estimates of the diameter of the projectile range from 100 to 500 m. By many orders of magnitude, this is the most massive achondrite sampled by a single meteorite fall.

NASA's Hubble Sees A New Supernova Remnant Light Up

NASA Image and Video Library

2011-06-10

NASA image release June 10, 2011 Astronomers using NASA's Hubble Space Telescope are witnessing the unprecedented transition of a supernova to a supernova remnant, where light from an exploding star in a neighboring galaxy, the Large Magellanic Cloud, reached Earth in February 1987. Named Supernova 1987A, it was the closest supernova explosion witnessed in almost 400 years. The supernova's close proximity to Earth has allowed astronomers to study it in detail as it evolves. Now, the supernova debris, which has faded over the years, is brightening. This means that a different power source has begun to light the debris. The debris of SN 1987A is beginning to impact the surrounding ring, creating powerful shock waves that generate X-rays observed with NASA's Chandra X-ray Observatory. Those X-rays are illuminating the supernova debris and shock heating is making it glow in visible light. The results are being reported in the June 9, 2011, issue of the journal Nature by a team including Robert Kirshner of the Harvard-Smithsonian Center for Astrophysics (CfA), who leads a long-term study of SN 1987A with Hubble. Since its launch in 1990, the Hubble telescope has provided a continuous record of the changes in SN 1987A. Credit: NASA, ESA, and P. Challis (Harvard-Smithsonian Center for Astrophysics) NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Join us on Facebook Find us on Instagram

Properties of interstellar wind leading to shape morphology of the dust surrounding HD 61005

NASA Astrophysics Data System (ADS)

Pástor, P.

2017-08-01

Aims: A structure formed by dust particles ejected from the debris ring around HD 61005 is observed in the scattered light. The main aim here is to constrain interstellar wind parameters that lead to shape morphology in the vicinity of HD 61005 using currently available observational data for the debris ring. Methods: Equation of motion of 2 × 105 dust particles ejected from the debris ring under the action of the electromagnetic radiation, stellar wind, and interstellar wind is solved. A two-dimensional (2D) grid is placed in a given direction for accumulation of the light scattered on the dust particles in order to determine the shape morphology. The interaction of the interstellar wind and the stellar wind is considered. Results: Groups of unknown properties of the interstellar wind that create the observed morphology are determined. A relation between number densities of gas components in the interstellar wind and its relative velocity is found. Variations of the shape morphology caused by the interaction with the interstellar clouds of various temperatures are studied. When the interstellar wind velocity is tilted from debris ring axis a simple relation between the properties of the interstellar wind and an angle between the line of sight and the interstellar wind velocity exists. Dust particles that are most significantly influenced by stellar radiation move on the boundary of observed structure. Conclusions: Observed structure at HD 61005 can be explained as a result of dust particles moving under the action of the interstellar wind. Required number densities or velocities of the interstellar wind are much higher than that of the interstellar wind entering the solar system.

Tidal Debris from High-Velocity Collisions as Fake Dark Galaxies: A Numerical Model of VIRGOHI 21

NASA Astrophysics Data System (ADS)

Duc, Pierre-Alain; Bournaud, Frederic

2008-02-01

High-speed collisions, although current in clusters of galaxies, have long been neglected, as they are believed to cause little damages to galaxies except when they are repeated, a process called "harassment." In fact, they are able to produce faint but extended gaseous tails. Such low-mass, starless, tidal debris may become detached and appear as free-floating clouds in the very deep H I surveys that are currently being carried out. We show in this paper that these debris possess the same apparent properties as the so-called dark galaxies, objects originally detected in H I, with no optical counterpart, and presumably dark matter-dominated. We present a numerical model of the prototype of such dark galaxies—VIRGOHI 21—that is able to reproduce its main characteristics: the one-sided tail linking it to the spiral galaxy NGC 4254, the absence of stars, and above all the reversal of the velocity gradient along the tail originally attributed to rotation motions caused by a massive dark matter halo, which we find to be consistent with simple streaming motions plus projection effects. According to our numerical simulations, this tidal debris was expelled 750 Myr ago during a flyby at 1100 km s-1 of NGC 4254 by a massive companion that should now lie at a projected distance of about 400 kpc. A candidate for the intruder is discussed. The existence of galaxies that have never been able to form stars had already been challenged on the basis of theoretical and observational grounds. Tidal collisions, in particular those occurring at high speed, provide a much more simple explanation for the origin of such putative dark galaxies.

Effects of Deadly California Debris Flows Seen in Before/After Images from NASA's UAVSAR

NASA Image and Video Library

2018-02-12

Extreme winter rains in January 2018 following the Thomas Fire in Ventura and Santa Barbara Counties caused severe debris flows, resulting in significant loss of life and considerable property damage in the town on Montecito, just east of Santa Barbara. NASA's Uninhabited Aerial Vehicle Synthetic Aperture Radar (UAVSAR) airborne radar platform detected changes caused by the debris flows between two images acquired on Nov. 2, 2017, and Feb. 5, 2018. An enhanced image pair (top left) shows disturbed areas in orange. In areas of severe surface disruption from the fire scar and debris flows the two image pairs can't be matched and decorrelate (top right). In the middle panels, the radar images are overlaid on the structure damage map produced by the County of Santa Barbara. The fire scars and damage correspond well with the risk map (lower left) and damage map (lower right). With an operational system, products such as these have the potential to augment information available for search and rescue, and for damage assessment for government agencies or the insurance industry. Radar has the advantage of being available in all weather conditions, as it can image through clouds. NASA's Uninhabited Aerial Vehicle Synthetic Aperture Radar (UAVSAR), developed and managed by the Jet Propulsion Laboratory, Pasadena, California, can record changes on the ground beneath the aircraft that occur between multiple flights, which take exactly the same flight path. The instrument is used to monitor how volcanoes, earthquakes, and other natural hazards are changing Earth. The JPL UAVSAR team collected and processed the imagery for Principal Investigator Andrea Donnellan who performed the analysis. She has been conducting ground change research using UAVSAR in this and other regions of California since 2009. https://photojournal.jpl.nasa.gov/catalog/PIA22243

Earth Satellite Population Instability: Underscoring the Need for Debris Mitigation

NASA Technical Reports Server (NTRS)

Liou, Jer-chyi; Johnson, N. L.

2006-01-01

A recent study by NASA indicates that the implementation of international orbital debris mitigation measures alone will not prevent a significant increase in the artificial Earth satellite population, beginning in the second half of this century. Whereas the focus of the aerospace community for the past 25 years has been on the curtailment of the generation of long-lived orbital debris, active remediation of the current orbital debris population should now be reconsidered to help preserve near-Earth space for future generations. In particular, we show in this paper that even if launch operations were to cease today, the population of space debris would continue to grow. Further, proposed remediation techniques do not appear to offer a viable solution. We therefore recommend that, while the aerospace community maintains the current debris-limiting mission regulations and postmission disposal procedures, future emphasis should be placed on finding new remediation technologies for solving this growing problem. Since the launch of Sputnik 1, space activities have created an orbital debris environment that poses increasing impact risks to existing space systems, including human space flight and robotic missions (1, 2). Currently, more than 9,000 Earth orbiting man-made objects (including many breakup fragments), with a combined mass exceeding 5 million kilograms, are tracked by the US Space Surveillance Network and maintained in the US satellite catalog (3-5). Three accidental collisions between cataloged satellites during the period from late 1991 to early 2005 have already been documented (6), although fortunately none resulted in the creation of large, trackable debris clouds. Several studies conducted during 1991-2001 demonstrated, with assumed future launch rates, the unintended growth potential of the Earth satellite population, resulting from random, accidental collisions among resident space objects (7-13). In some low Earth orbit (LEO) altitude regimes where the number density of satellites is above a critical spatial density, the production rate of new satellites (i.e., debris) due to collisions exceeds the loss of objects due to orbital decay. NASA s evolutionary satellite population model LEGEND (LEO-to-GEO Environment Debris model), developed by the Orbital Debris Program Office at the NASA Lyndon B. Johnson Space Center, is a high fidelity three-dimensional physical model that is capable of simulating the historical satellite environment, as well as the evolution of future debris populations (14, 15). The subject study assumed no rocket bodies and spacecraft were launched after December 2004, and no future disposal maneuvers were allowed for existing spacecraft, few of which currently have such a capability. The rate of satellite explosions would naturally decrease to zero within a few decades as the current satellite population ages. The LEGEND future projection adopts a Monte Carlo approach to simulate future on-orbit explosions and collisions. Within a given projection time step, once the explosion probability is estimated for an intact object, a random number is drawn and compared with the probability to determine if an explosion would occur. A similar procedure is applied to collisions for each pair of target and projectile involved within the same time step. Due to the nature of the Monte Carlo process, multiple projection runs must be performed and analyzed before one can draw reliable and meaningful conclusions from the outcome. A total of fifty, 200-year future projection Monte Carlo simulations were executed and evaluated (16).

Estimating ice albedo from fine debris cover quantified by a semi-automatic method: the case study of Forni Glacier, Italian Alps

NASA Astrophysics Data System (ADS)

Azzoni, Roberto Sergio; Senese, Antonella; Zerboni, Andrea; Maugeri, Maurizio; Smiraglia, Claudio; Diolaiuti, Guglielmina Adele

2016-03-01

In spite of the quite abundant literature focusing on fine debris deposition over glacier accumulation areas, less attention has been paid to the glacier melting surface. Accordingly, we proposed a novel method based on semi-automatic image analysis to estimate ice albedo from fine debris coverage (d). Our procedure was tested on the surface of a wide Alpine valley glacier (the Forni Glacier, Italy), in summer 2011, 2012 and 2013, acquiring parallel data sets of in situ measurements of ice albedo and high-resolution surface images. Analysis of 51 images yielded d values ranging from 0.01 to 0.63 and albedo was found to vary from 0.06 to 0.32. The estimated d values are in a linear relation with the natural logarithm of measured ice albedo (R = -0.84). The robustness of our approach in evaluating d was analyzed through five sensitivity tests, and we found that it is largely replicable. On the Forni Glacier, we also quantified a mean debris coverage rate (Cr) equal to 6 g m-2 per day during the ablation season of 2013, thus supporting previous studies that describe ongoing darkening phenomena at Alpine debris-free glaciers surface. In addition to debris coverage, we also considered the impact of water (both from melt and rainfall) as a factor that tunes albedo: meltwater occurs during the central hours of the day, decreasing the albedo due to its lower reflectivity; instead, rainfall causes a subsequent mean daily albedo increase slightly higher than 20 %, although it is short-lasting (from 1 to 4 days).

How predictable is the behaviour of torrential processes: two case studies of the summer 2012

NASA Astrophysics Data System (ADS)

Huebl, Johannes; Eisl, Julia; Janu, Stefan; Hanspeter, Pussnig

2013-04-01

Debris flow hazards play an important role in the Austrian Alps since many villages are located on alluvial fans. Most of the mitigation Measures as well as Hazard Zone Maps are designed by engineers of previous generations, who know quite a lot about the torrential behaviour from their experience. But speaking in terms of recurrence intervals of 100 years or even more, human memory is restricted. On the other hand numerical modelling is a fast growing task in dealing with natural hazards. Scenarios of torrential hazards can be defined and accordant deposition pattern, flow depths and velocities are calculated. But of course, errors in the input data must lead to fatal errors in the results, consequently threaten human life in possible affected areas. Thus the need for data collection of exceptional events can help to reproduce the reality in a quite high grade, indeed, but unexpected events are still an issue and pose a challenge to engineers. In summer 2012 two debris flow events occurred in Austria with quite different behaviours, from triggering mechanism and flow behaviour through to deposition: Thunderstorms or long lasting rainfall, slope failures with subsequent channel blockage and dike breaching or linear erosion, one or more debris flows, one huge debris flow surge or a series of debris flow surges, sediments without clay or cohesive material, near channel deposition or outspread deposits. Both debris flows have been unexpected in their dimension, although mitigation measures and hazard maps exist. Both events were documented accurately, first to try to understand the torrential process occurred, second to identify the most fitting mitigation measures, ranging from permanent structures to temporary warning systems.

A debris avalanche at Süphan stratovolcano (Turkey) and implications for hazard evaluation

NASA Astrophysics Data System (ADS)

Özdemir, Yavuz; Akkaya, İsmail; Oyan, Vural; Kelfoun, Karim

2016-02-01

The Quaternary Süphan debris avalanche deposit is located in Eastern Anatolia, Turkey. The avalanche formed by the sector collapse of a major stratovolcano towards the north, possibly during a single catastrophic event. The deposit has an estimated volume of 4 km3 and ran out over 25 km to cover an area of approximately 200 km2. Products of the collapse are overlain by younger eruptive units from the Süphan volcano. We have tested the numerical code VolcFlow to first reproduce the emplacement of the Quaternary Süphan debris avalanche and then to develop a hazard assessment for potential future sector collapses and subsequent emplacement of debris avalanches and associated tsunami. The numerical model captures the main features of the propagation process, including travel distance, lateral spread, and run up. The best fit obtained for the existing flow has a constant retarding stress of 50 kPa and a collapse scar volume of 4 km3. Analysis of potential future collapse scenarios reveals that northern sector debris avalanches (up to 6 km3) could affect several towns. In the case of a sector collapse towards the south, a tsunami will reach the city of Van and several of the biggest towns on the southern shoreline of Lake Van. Cities most affected by the larger amplitude waves would be Van, Edremit, Gevaş, Tatvan, and, to a lesser extent, Erciş, with wave amplitudes (first waves after the onset of the collapse) between 8 and 10 m.

Substantial convection and precipitation enhancements by ultrafine aerosol particles

DOE PAGES

Fan, Jiwen; Rosenfeld, Daniel; Zhang, Yuwei; ...

2018-01-26

Aerosol-cloud interactions remain the largest uncertainty in climate projections. Ultrafine aerosol particles smaller than 50 nanometers (UAP <50) can be abundant in the troposphere, but are conventionally considered too small to affect cloud formation. However, observational evidence and numerical simulations of deep convective clouds (DCCs) over the Amazon show that DCCs forming in a low aerosol environment can develop very large vapor supersaturation because fast droplet coalescence reduces integrated droplet surface area and subsequent condensation. UAP <50 from pollution plumes that are ingested into such clouds can be activated to form additional cloud droplets on which excess supersaturation condenses andmore » forms additional cloud water and latent heating, thus intensifying convective strength. This mechanism suggests a strong anthropogenic invigoration of DCCs in previously pristine regions of the world.« less

Entrainment in Laboratory Simulations of Cumulus Cloud Flows

NASA Astrophysics Data System (ADS)

Narasimha, R.; Diwan, S.; Subrahmanyam, D.; Sreenivas, K. R.; Bhat, G. S.

2010-12-01

A variety of cumulus cloud flows, including congestus (both shallow bubble and tall tower types), mediocris and fractus have been generated in a water tank by simulating the release of latent heat in real clouds. The simulation is achieved through ohmic heating, injected volumetrically into the flow by applying suitable voltages between diametral cross-sections of starting jets and plumes of electrically conducting fluid (acidified water). Dynamical similarity between atmospheric and laboratory cloud flows is achieved by duplicating values of an appropriate non-dimensional heat release number. Velocity measurements, made by laser instrumentation, show that the Taylor entrainment coefficient generally increases just above the level of commencement of heat injection (corresponding to condensation level in the real cloud). Subsequently the coefficient reaches a maximum before declining to the very low values that characterize tall cumulus towers. The experiments also simulate the protected core of real clouds. Cumulus Congestus : Atmospheric cloud (left), simulated laboratory cloud (right). Panels below show respectively total heat injected and vertical profile of heating in the laboratory cloud.

Spectral features of tidal disruption candidates and alternative origins for such transient flares

NASA Astrophysics Data System (ADS)

Saxton, Curtis J.; Perets, Hagai B.; Baskin, Alexei

2018-03-01

UV and optically selected candidates for stellar tidal disruption events (TDEs) often exhibit broad spectral features (He II emission, H α emission, or absorption lines) on a blackbody-like continuum (104 K≲ T≲ 105 K). The lines presumably emit from TDE debris or circumnuclear clouds photoionized by the flare. Line velocities however are much lower than expected from a stellar disruption by supermassive black hole (SMBH), and are somewhat faster than expected for the broad line region (BLR) clouds of a persistently active galactic nucleus (AGN). The distinctive spectral states are not strongly related to observed luminosity and velocity, nor to SMBH mass estimates. We use exhaustive photoionization modelling to map the domain of fluxes and cloud properties that yield (e.g.) an He-overbright state where a large He II(4686 Å)/H α line ratio creates an illusion of helium enrichment. Although observed line ratios occur in a plausible minority of cases, AGN-like illumination cannot reproduce the observed equivalent widths. We therefore propose to explain these properties by a light-echo photoionization model: the initial flash of a hot blackbody (detonation) excites BLR clouds, which are then seen superimposed on continuum from a later, expanded, cooled stage of the luminous source. The implied cloud mass is substellar, which may be inconsistent with a TDE. Given these and other inconsistencies with TDE models (e.g. host-galaxies distribution) we suggest to also consider alternative origins for these nuclear flares, which we briefly discuss (e.g. nuclear supernovae and starved/subluminous AGNs).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Caldecott, Ralph; Kamarulzaman, Dayangku N. S.; Kirrane, James P.

The concept of momentum exchange when applied to space tethers for propulsion is well established, and a considerable body of literature now exists on the on-orbit modelling, the dynamics, and also the control of a large range of tether system applications. The authors consider here a new application for the Motorised Momentum Exchange Tether by highlighting three key stages of development leading to a conceptualisation that can subsequently be developed into a technology for Active Debris Removal. The paper starts with a study of the on-orbit mechanics of a full sized motorised tether in which it is shown that amore » laden and therefore highly massasymmetrical tether can still be forced to spin, and certainly to librate, thereby confirming its possible usefulness for active debris removal (ADR). The second part of the paper concentrates on the modelling of the centripetal deployment of a symmetrical MMET in order to get it initialized for debris removal operations, and the third and final part of the paper provides an entry into scale modelling for low cost mission design and testing. It is shown that the motorised momentum exchange tether offers a potential solution to the removal of large pieces of orbital debris, and that dynamic methodologies can be implemented to in order to optimise the emergent design.« less

Experimental testing of impact force on rigid and flexible barriers - A comparison

NASA Astrophysics Data System (ADS)

Nagl, Georg; Hübl, Johannes; Chiari, Michael

2016-04-01

The Trattenbach endangers the main western railway track of Austria by floods and debris flows. Three check dams for debris retention were built in the proximal fan area several decades ago. With regard to an improvement of the protective function, these structures have to be renewed. The recent concept of the uppermost barrier is a type of an energy dissipation net structure, stopping debris flows with the ability of self-cleaning by subsequent floods or by machinery employment. The access to the basin is achieved through the slit when the net has been removed. This technical structure consists of a rigid open crown dam with a 4m wide slit. This slit is closed with a flexible net. To verify this protective system, 21 small scale experiments were conducted to test and optimize this new type of Slit Net Dam. To determine the forces on the barrier, in a first setup of experiments the impact forces on a rigid wall with 24 load cells were measured. In the second setup the slit barrier with the net was investigated. On four main cables the anchor forces were measured. In a further setup the basal distance between the channel and lowest net was varied. To study the emptying of the basin and the dosing effect on debris flows.

Flank collapse at Mount Wrangell, Alaska, recorded by volcanic mass-flow deposits in the Copper River lowland

USGS Publications Warehouse

Waythomas, C.F.; Wallace, K.L.

2002-01-01

An areally extensive volcanic mass-flow deposit of Pleistocene age, known as the Chetaslina volcanic mass-flow deposit, is a prominent and visually striking deposit in the southeastern Copper River lowland of south-central Alaska. The mass-flow deposit consists of a diverse mixture of colorful, variably altered volcanic rocks, lahar deposits, glaciolacustrine diamicton, and till that record a major flank collapse on the southwest flank of Mount Wrangell. The deposit is well exposed near its presumed source, and thick, continuous, stratigraphic exposures have permitted us to study its sedimentary characteristics as a means of better understanding the origin, significance, and evolution of the deposit. Deposits of the Chetaslina volcanic mass flow in the Chetaslina River drainage are primary debris-avalanche deposits and consist of two principal facies types, a near-source block facies and a distal mixed facies. The block facies is composed entirely of block-supported, shattered and fractured blocks with individual blocks up to 40 m in diameter. The mixed facies consists of block-sized particles in a matrix of poorly sorted rock rubble, sand, and silt generated by the comminution of larger blocks. Deposits of the Chetaslina volcanic mass flow exposed along the Copper, Tonsina, and Chitina rivers are debris-flow deposits that evolved from the debris-avalanche component of the flow and from erosion and entrainment of local glacial and glaciolacustrine diamicton in the Copper River lowland. The debris-flow deposits were probably generated through mixing of the distal debris avalanche with the ancestral Copper River, or through breaching of a debris-avalanche dam across the ancestral river. The distribution of facies types and major-element chemistry of clasts in the deposit indicate that its source was an ancestral volcanic edifice, informally known as the Chetaslina vent, on the southwest side of Mount Wrangell. A major sector collapse of the Chetaslina vent initiated the Chetaslina volcanic mass flow forming a debris avalanche of about 4 km3 that subsequently transformed to a debris flow of unknown volume.

Measuring the structure and composition of circumstellar debris disks

NASA Astrophysics Data System (ADS)

Ballering, Nicholas Paul

In this dissertation, I measure the structure and composition of circumstellar debris disks to probe the underlying planetary systems. In Chapter 1, I provide an introduction to the field of debris disks. I highlight our current observational and theoretical understanding of the field, rather than providing a detailed history. This is intended to give the reader context and motivation for the subsequent chapters. I also describe important developments in debris disk science that are not the focus of this dissertation, but are nevertheless vital for a complete overview. In Chapter 2, I describe my analysis of a large sample of cold (<130 K) debris disks seen in Spitzer/IRS data. Previous work had suggested a common temperature for these disk components, regardless of spectral type. I find that there is trend with spectral type and argue that the locations of cold disks are not set by snow lines, but more likely by the formation/evolution of planets. This work was published in Ballering et al. (2013). In Chapter 3, I turn my focus to the warm (˜190 K) debris components identified in Chapter 2--specifically those exhibiting silicate emission features. I show that these features arise from exozodiacal dust in the habitable zones around these stars. This was published in Ballering et al. (2014). In Chapter 4, I examine the remainder of the warm disks to investigate what mechanism sets their location. I find that for many systems, the locations trace the water snow line in the primordial protoplanetary disk, rather than the current snow line. This favors the interpretation that warm debris components arise from asteroid belts in these systems. This study will be published soon. In Chapter 5, I analyze images of the debris disk around beta Pictoris at five different wavelengths, including in thermal emission and scattered light. I find that matching the disk brightness at all wavelengths constrains the composition of the dust, with a mixture of astronomical silicates and organic refractory material fitting the data well. This was published in Ballering et al. (2016). In Chapter 6, I conclude with a summary of this dissertation and prospects for future progress in these areas.

Observational evidence for cloud cover enhancement over western European forests.

PubMed

Teuling, Adriaan J; Taylor, Christopher M; Meirink, Jan Fokke; Melsen, Lieke A; Miralles, Diego G; van Heerwaarden, Chiel C; Vautard, Robert; Stegehuis, Annemiek I; Nabuurs, Gert-Jan; de Arellano, Jordi Vilà-Guerau

2017-01-11

Forests impact regional hydrology and climate directly by regulating water and heat fluxes. Indirect effects through cloud formation and precipitation can be important in facilitating continental-scale moisture recycling but are poorly understood at regional scales. In particular, the impact of temperate forest on clouds is largely unknown. Here we provide observational evidence for a strong increase in cloud cover over large forest regions in western Europe based on analysis of 10 years of 15 min resolution data from geostationary satellites. In addition, we show that widespread windthrow by cyclone Klaus in the Landes forest led to a significant decrease in local cloud cover in subsequent years. Strong cloud development along the downwind edges of larger forest areas are consistent with a forest-breeze mesoscale circulation. Our results highlight the need to include impacts on cloud formation when evaluating the water and climate services of temperate forests, in particular around densely populated areas.

Observational evidence for cloud cover enhancement over western European forests

PubMed Central

Teuling, Adriaan J.; Taylor, Christopher M.; Meirink, Jan Fokke; Melsen, Lieke A.; Miralles, Diego G.; van Heerwaarden, Chiel C.; Vautard, Robert; Stegehuis, Annemiek I.; Nabuurs, Gert-Jan; de Arellano, Jordi Vilà-Guerau

2017-01-01

Forests impact regional hydrology and climate directly by regulating water and heat fluxes. Indirect effects through cloud formation and precipitation can be important in facilitating continental-scale moisture recycling but are poorly understood at regional scales. In particular, the impact of temperate forest on clouds is largely unknown. Here we provide observational evidence for a strong increase in cloud cover over large forest regions in western Europe based on analysis of 10 years of 15 min resolution data from geostationary satellites. In addition, we show that widespread windthrow by cyclone Klaus in the Landes forest led to a significant decrease in local cloud cover in subsequent years. Strong cloud development along the downwind edges of larger forest areas are consistent with a forest-breeze mesoscale circulation. Our results highlight the need to include impacts on cloud formation when evaluating the water and climate services of temperate forests, in particular around densely populated areas. PMID:28074840

Numerical modelling of the formation process of planets from protoplanetary cloud

NASA Technical Reports Server (NTRS)

Kozlov, N. N.; Eneyev, T. M.

1979-01-01

Evolution of the plane protoplanetary cloud, consisting of a great number of gravitationally interacting and uniting under collision bodies (protoplanets) moving in the central field of a large mass (the Sun or a planet), is considered. It is shown that in the course of protoplanetary cloud evolution the ring zones of matter expansion and compression occur with the subsequent development leading to formation of planets, rotating about their axes mainly directly. The principal numerical results were obtained through digital simulation of planetary accumulation.

Assessment of the consequences of the Fengyun-1C breakup in low Earth orbit

NASA Astrophysics Data System (ADS)

Pardini, Carmen

On 11 January 2007, the 880 kg (958 kg at launch) weather spacecraft Fengyun-1C, launched on 10 May 1999 into a sun-synchronous orbit with a CZ-4B booster from the Taiyuan Satellite Launch Center, was destroyed over central China as a result of the first successful Chinese anti-satellite weapon test. It was carried out with a direct ascent interception with a kinetic energy kill vehicle launched by an SC-19 missile, fired from a mobile ground platform close to the Xichang Satellite Launch Center. While the technical details of the test, probably the third attempt, and the characteristics of the weapon used remain shrouded in secrecy, the intentional breakup of the aging weather spacecraft, fully functional until 2005, produced a huge amount of debris in one of the orbital regimes already most affected by past fragmentation events. At present, the US Space Surveillance Network has identified about 2600 objects, typically larger than 10 cm, but the fragments larger than 1 cm may be more than 100,000. After two decades of substantial international progress in the field of orbital debris mitigation, in order to preserve the low Earth and geosynchronous environments for future space missions, the Fengyun-1C destruction represented a serious turnabout. In fact, it abruptly increased by approximately 20% the number of cataloged debris in orbit. To give a rough idea of the impact of this single event on the circumterrestrial environment, it is sufficient to realize that about 15 years of global space activity - including failures and accidental breakups - had been needed to increase, by a comparable amount, the number of cataloged debris in orbit to the level observed before the Chinese anti-satellite test. The purpose of this presentation is to assess the impact of the debris cloud generated by the Fengyun-1C breakup on the low Earth environment. The anti-satellite test was carried out at an altitude of about 863 km, spreading the cataloged fragments between 200 and 4000 km, with maximum concentration around the breakup height. The environmental impact was particularly significant in all the altitude range between 700 and 1000 km, where the debris density due to past space activities was already at worrisome levels. Considering the inclination, nearly polar, and the height of the target, such a deliberate act of debris generation was therefore one of worst conceivable with current technology and its consequences will unfortunately be felt for many decades.

GOES Cloud Detection at the Global Hydrology and Climate Center

NASA Technical Reports Server (NTRS)

Laws, Kevin; Jedlovec, Gary J.; Arnold, James E. (Technical Monitor)

2002-01-01

The bi-spectral threshold (BTH) for cloud detection and height assignment is now operational at NASA's Global Hydrology and Climate Center (GHCC). This new approach is similar in principle to the bi-spectral spatial coherence (BSC) method with improvements made to produce a more robust cloud-filtering algorithm for nighttime cloud detection and subsequent 24-hour operational cloud top pressure assignment. The method capitalizes on cloud and surface emissivity differences from the GOES 3.9 and 10.7-micrometer channels to distinguish cloudy from clear pixels. Separate threshold values are determined for day and nighttime detection, and applied to a 20-day minimum composite difference image to better filter background effects and enhance differences in cloud properties. A cloud top pressure is assigned to each cloudy pixel by referencing the 10.7-micrometer channel temperature to a thermodynamic profile from a locally -run regional forecast model. This paper and supplemental poster will present an objective validation of nighttime cloud detection by the BTH approach in comparison with previous methods. The cloud top pressure will be evaluated by comparing to the NESDIS operational CO2 slicing approach.

Discrete Element Modelling of Floating Debris

NASA Astrophysics Data System (ADS)

Mahaffey, Samantha; Liang, Qiuhua; Parkin, Geoff; Large, Andy; Rouainia, Mohamed

2016-04-01

Flash flooding is characterised by high velocity flows which impact vulnerable catchments with little warning time and as such, result in complex flow dynamics which are difficult to replicate through modelling. The impacts of flash flooding can be made yet more severe by the transport of both natural and anthropogenic debris, ranging from tree trunks to vehicles, wheelie bins and even storage containers, the effects of which have been clearly evident during recent UK flooding. This cargo of debris can have wide reaching effects and result in actual flood impacts which diverge from those predicted. A build-up of debris may lead to partial channel blockage and potential flow rerouting through urban centres. Build-up at bridges and river structures also leads to increased hydraulic loading which may result in damage and possible structural failure. Predicting the impacts of debris transport; however, is difficult as conventional hydrodynamic modelling schemes do not intrinsically include floating debris within their calculations. Subsequently a new tool has been developed using an emerging approach, which incorporates debris transport through the coupling of two existing modelling techniques. A 1D hydrodynamic modelling scheme has here been coupled with a 2D discrete element scheme to form a new modelling tool which predicts the motion and flow-interaction of floating debris. Hydraulic forces arising from flow around the object are applied to instigate its motion. Likewise, an equivalent opposing force is applied to fluid cells, enabling backwater effects to be simulated. Shock capturing capabilities make the tool applicable to predicting the complex flow dynamics associated with flash flooding. The modelling scheme has been applied to experimental case studies where cylindrical wooden dowels are transported by a dam-break wave. These case studies enable validation of the tool's shock capturing capabilities and the coupling technique applied between the two numerical schemes. The results show that the tool is able to adequately replicate water depth and depth-averaged velocity of a dam-break wave, as well as velocity and displacement of floating cylindrical elements, thus validating its shock capturing capabilities and the coupling technique applied for this simple test case. Future development of the tool will incorporate a 2D hydrodynamic scheme and a 3D discrete element scheme in order to model the more complex processes associated with debris transport.

NASA Glenn Icing Research Tunnel: Upgrade and Cloud Calibration

NASA Technical Reports Server (NTRS)

VanZante, Judith Foss; Ide, Robert F.; Steen, Laura E.

2012-01-01

In 2011, NASA Glenn s Icing Research Tunnel underwent a major modification to it s refrigeration plant and heat exchanger. This paper presents the results of the subsequent full cloud calibration. Details of the calibration procedure and results are presented herein. The steps include developing a nozzle transfer map, establishing a uniform cloud, conducting a drop sizing calibration and finally a liquid water content calibration. The goal of the calibration is to develop a uniform cloud, and to build a transfer map from the inputs of air speed, spray bar atomizing air pressure and water pressure to the output of median volumetric droplet diameter and liquid water content.

NASA Glenn Icing Research Tunnel: 2012 Cloud Calibration Procedure and Results

NASA Technical Reports Server (NTRS)

VanZante, Judith Foss; Ide, Robert F.; Steen, Laura E.

2012-01-01

In 2011, NASA Glenn s Icing Research Tunnel underwent a major modification to it s refrigeration plant and heat exchanger. This paper presents the results of the subsequent full cloud calibration. Details of the calibration procedure and results are presented herein. The steps include developing a nozzle transfer map, establishing a uniform cloud, conducting a drop sizing calibration and finally a liquid water content calibration. The goal of the calibration is to develop a uniform cloud, and to build a transfer map from the inputs of air speed, spray bar atomizing air pressure and water pressure to the output of median volumetric droplet diameter and liquid water content.

Prize of the best thesis 2015: Study of debris discs through state-of-the-art numerical modelling

NASA Astrophysics Data System (ADS)

Kral, Q.; Thébault, P.

2015-12-01

This proceeding summarises the thesis entitled ``Study of debris discs with a new generation numerical model'' by Quentin Kral, for which he obtained the prize of the best thesis in 2015. The thesis brought major contributions to the field of debris disc modelling. The main achievement is to have created, almost ex-nihilo, the first truly self-consistent numerical model able to simultaneously follow the coupled collisional and dynamical evolutions of debris discs. Such a code has been thought as being the ``Holy Grail'' of disc modellers for the past decade, and while several codes with partial dynamics/collisions coupling have been presented, the code developed in this thesis, called ``LIDT-DD'' is the first to achieve a full coupling. The LIDT-DD model, which is the first of a new-generation of fully self-consistent debris disc models is able to handle both planetesimals and dust and create new fragments after each collision. The main idea of LIDT-DD development was to merge into one code two approaches that were so far used separately in disc modelling, that is, an N-body algorithm to investigate the dynamics, and a statistical scheme to explore the collisional evolution. This complex scheme is not straightforward to develop as there are major difficulties to overcome: 1) collisions in debris discs are highly destructive and produce clouds of small fragments after each single impact, 2) the smallest (and most numerous) of these fragments have a strongly size-dependent dynamics because of the radiation pressure, and 3) the dust usually observed in discs is precisely these smallest grains. These extreme constraints had so far prevented all previous attempts at developing self-consistent disc models to succeed. The thesis contains many examples of the use of LIDT-DD that are not yet published but the case of the collision between two asteroid-like bodies is studied in detail. In particular, LIDT-DD is able to predict the different stages that should be observed after such massive collisions that happen mainly in the latest stages of planetary formation. Some giant impact signatures and observability predictions for VLT/SPHERE and JWST/MIRI are given. JWST should be able to detect many of such impacts and would enable to see on-going planetary formation in dozens of planetary systems.

Activity of (2060) Chiron possibly caused by impacts?

NASA Astrophysics Data System (ADS)

Cikota, Stefan; Fernández-Valenzuela, Estela; Ortiz, Jose Luis; Morales, Nicolás; Duffard, René; Aceituno, Jesus; Cikota, Aleksandar; Santos-Sanz, Pablo

2018-04-01

The centaur 95P/(2060) Chiron is showing comet-like activity since its discovery, but the mass-loss mechanisms triggering its activity remained unexplained. Although the collision rates in the centaur region are expected to be very low, and impacts are thought not to be responsible for the mass-loss, since the recent indications that Chiron might possess a ring similar to Chariklo's, and assuming that there is debris orbiting around, the impact triggered mass-loss mechanism should not be excluded as a possible cause of its activity. From time series observations collected on Calar Alto Observatory in Spain between 2014 and 2016, we found that the photometric scatter in Chiron's data is larger than a control star's scatter, indicating a possible microactivity, possibly caused by debris falling back to Chiron's surface and lifting small clouds of material. We also present rotational light curves, and measurements of Chiron's absolute magnitudes, which are consistent with the models supporting the presumption that Chiron possesses rings. By co-adding the images acquired in 2015, we have detected an ˜5 arcsec long tail, showing a surface brightness of 25.3 mag(V) arcsec-2.

Inhibitory effects of melatonin on titanium particle-induced inflammatory bone resorption and osteoclastogenesis via suppression of NF-κB signaling.

PubMed

Ping, Zichuan; Wang, Zhirong; Shi, Jiawei; Wang, Liangliang; Guo, Xiaobin; Zhou, Wei; Hu, Xuanyang; Wu, Xiexing; Liu, Yu; Zhang, Wen; Yang, Huilin; Xu, Yaozeng; Gu, Ye; Geng, Dechun

2017-10-15

Wear debris-induced peri-implant osteolysis challenges the longevity of implants. The host response to wear debris causes chronic inflammation, promotes bone resorption, and impairs bone formation. We previously demonstrated that melatonin enhances bone formation and attenuates wear debris-induced bone loss in vivo. However, whether melatonin inhibits chronic inflammation and bone resorption at sites of wear debris-induced osteolysis remains unclear. In this study, we examined the potential inhibitory effects of melatonin on titanium particle-induced inflammatory osteolysis in a murine calvarial model and on RANKL-induced osteoclastic formation in bone marrow-derived macrophages. We found that the exogenous administration of melatonin significantly inhibited wear debris-induced bone resorption and the expression of inflammatory cytokines in vivo. Additionally, melatonin inhibited RANKL-induced osteoclast differentiation, F-actin ring formation, and osteoclastic resorption in a concentration-dependent manner in vitro. We also showed that melatonin blocked the phosphorylation of IκB-α and p65, but not IKKα, and significantly inhibited the expression of NFATc1 and c-Fos. However, melatonin had no effect on MAPK or PI3K/AKT signaling pathways. These results provide novel mechanistic insight into the anti-inflammatory and anti-bone resorptive effects of melatonin on wear debris-induced bone loss and provide an evidence-based rationale for the protective effects of melatonin as a treatment for peri-implant osteolysis. Wear debris-induced chronic inflammation, osteoclastic activation and osteoblastic inhibition have been identified as critical factors of peri-implant bone loss. We previously demonstrated that melatonin, a bioactive indolamine secreted mainly by the pineal gland, activates Wnt/β-catenin signaling pathway and enhances bone regeneration at osteolytic site in vivo. In the current study, we further demonstrated that melatonin significantly suppresses wear debris-induced bone resorption and inflammatory cytokine expression in vivo. In addition, melatonin inhibits receptor activator of nuclear factor kappa-B ligand induced osteoclast formation and osteoclastic bone resorption in vitro. Meanwhile, we found that melatonin mediates its anti-inflammation and anti-bone resorption effects by abrogating nuclear factor kappa-B activation. These results further support the protective effects of melatonin on wear debris-induced peri-implant bone loss, and strongly suggest that melatonin could be considered as a potential candidate for the prevention and treatment of wear debris-induced osteolysis and subsequent aseptic loosening. Copyright © 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

A Method to Estimate the Probability That Any Individual Cloud-to-Ground Lightning Stroke Was Within Any Radius of Any Point

NASA Technical Reports Server (NTRS)

Huddleston, Lisa L.; Roeder, William P.; Merceret, Francis J.

2010-01-01

A new technique has been developed to estimate the probability that a nearby cloud-to-ground lightning stroke was within a specified radius of any point of interest. This process uses the bivariate Gaussian distribution of probability density provided by the current lightning location error ellipse for the most likely location of a lightning stroke and integrates it to determine the probability that the stroke is inside any specified radius of any location, even if that location is not centered on or even within the location error ellipse. This technique is adapted from a method of calculating the probability of debris collision with spacecraft. Such a technique is important in spaceport processing activities because it allows engineers to quantify the risk of induced current damage to critical electronics due to nearby lightning strokes. This technique was tested extensively and is now in use by space launch organizations at Kennedy Space Center and Cape Canaveral Air Force station.

Preliminary Volcano-Hazard Assessment for Gareloi Volcano, Gareloi Island, Alaska

USGS Publications Warehouse

Coombs, Michelle L.; McGimsey, Robert G.; Browne, Brandon L.

2008-01-01

Gareloi Volcano (178.794 degrees W and 51.790 degrees N) is located on Gareloi Island in the Delarof Islands group of the Aleutian Islands, about 2,000 kilometers west-southwest of Anchorage and about 150 kilometers west of Adak, the westernmost community in Alaska. This small (about 8x10 kilometer) volcano has been one of the most active in the Aleutians since its discovery by the Bering expedition in the 1740s, though because of its remote location, observations have been scant and many smaller eruptions may have gone unrecorded. Eruptions of Gareloi commonly produce ash clouds and lava flows. Scars on the flanks of the volcano and debris-avalanche deposits on the adjacent seafloor indicate that the volcano has produced large landslides in the past, possibly causing tsunamis. Such events are infrequent, occurring at most every few thousand years. The primary hazard from Gareloi is airborne clouds of ash that could affect aircraft. In this report, we summarize and describe the major volcanic hazards associated with Gareloi.

A combined spectral and object-based approach to transparent cloud removal in an operational setting for Landsat ETM+

NASA Astrophysics Data System (ADS)

Watmough, Gary R.; Atkinson, Peter M.; Hutton, Craig W.

2011-04-01

The automated cloud cover assessment (ACCA) algorithm has provided automated estimates of cloud cover for the Landsat ETM+ mission since 2001. However, due to the lack of a band around 1.375 μm, cloud edges and transparent clouds such as cirrus cannot be detected. Use of Landsat ETM+ imagery for terrestrial land analysis is further hampered by the relatively long revisit period due to a nadir only viewing sensor. In this study, the ACCA threshold parameters were altered to minimise omission errors in the cloud masks. Object-based analysis was used to reduce the commission errors from the extended cloud filters. The method resulted in the removal of optically thin cirrus cloud and cloud edges which are often missed by other methods in sub-tropical areas. Although not fully automated, the principles of the method developed here provide an opportunity for using otherwise sub-optimal or completely unusable Landsat ETM+ imagery for operational applications. Where specific images are required for particular research goals the method can be used to remove cloud and transparent cloud helping to reduce bias in subsequent land cover classifications.

ROGER a potential orbital space debris removal system

NASA Astrophysics Data System (ADS)

Starke, Juergen; Bischof, Bernd; Foth, W.-O.; -J., J.; Günther

The previous activities in the field of On Orbit Servicing studied in the 1990's included in partic-ular the capability of vehicles in GEO to capture and support satellites (mainly communication satellites) to enable repair and continuation of operations, and finally the controlled transfer the target into a permanent graveyard orbit. The specific capture tools for these applications were mostly based on robotic systems to capture and fix the target under specific dynamic constraints (e.g. slowly tumbling target) without damage, and to allow the stabilization, re-orientation and potential repair of the target and subsequent release or transport to the final disposal orbit. Due to the drastically increasing number of debris particularly in the Low Earth Orbits (SSO) the active debris removal is now necessary to counteract to the predicted debris production cascade (Kessler Syndrome), which means the pollution of the total sphere in low earth orbit and not only the SSO area. In most of the debris congresses it was recommended to start removal with the still integrated systems as soon as possible. In the case of large debris objects, the soft capture system can be replaced by a simpler and robust system able to operate from a safe distance to the target and flexible enough to capture and hold different types of targets such as deactivated and/or defective satellites, upper stages and big fragments. These nominally non -cooperative targets might be partially destroyed by the capture process, but the production of additional debris shall be avoided. A major argument for the commercial applications is a multi-target mission potential, which is possible at GEO because the transfer propellant requirement to the disposal orbit and the return to the orbit of the next potential target is relative low (orbits with similar inclination and altitude). The proposed ROGER system is designed as a spacecraft with rendezvous capabilities including inspection in the vicinity of the target and stabilization and transportation features for the combined configuration. The capture system is a deployable and closable net. The net is ejected from the mother spacecraft at a safe distance to prevent any collision with the target. After transport to the disposal orbit the net will be cut and the spacecraft will return to the operational orbit of the next target. An initial down-scaled demonstration is planned for the net capture system on a parabolic flight in autumn 2010. Further representative demonstrations including, for example, one in LEO are under discussion. The capture system can be used operationally also in other orbits e.g. LEO, but the propellant requirements for transport of the target into a direct controlled re-entry orbit and the subsequent return of the mother spacecraft to a new target orbit will be very high. This could impact the multi mission capability of the system. The potential applications are under discussion with different customers including satellite operators, insurance companies and international organisations. juergen.starke@astrium.eads.net Tel.: +49-421-539-4573

Cannibalization of Dwarf Galaxies by the Milky Way: Distance to the Leading Arm of the Magellanic Clouds

NASA Astrophysics Data System (ADS)

Antwi-Danso, Jacqueline; Barger, Kathleen; Haffner, L. Matthew

2016-01-01

Tidal interactions between two dwarf galaxies near the Milky Way, the Large and Small Magellanic Clouds, have caused large quantities of gas to be flung into the halo of the Milky Way. Much of this tidal debris, known as the Magellanic System, is currently headed towards the disk of the Milky Way, spearheaded by the Leading Arm, with the Bridge connecting the two dwarf galaxies, and the trailing Magellanic Stream at the end. Estimates for the amount of gas that the Magellanic System contains are in the range of (2 - 4) × 109 M⊙ and this could supply our Galaxy with (3.7 - 6.7) M⊙ yr-1 (Fox et al. 2014). Although this is higher than the present star-formation rate of the Galaxy, the position of the tidal debris predisposes it to ionizing radiation from the extragalactic background and Galactic disk, as well as ram-pressure stripping from the halo, hindering gas accretion. Some parts of the Leading Arm, however, appear to have already survived the trip to the disk as their morphology is indicative of interaction with the interstellar medium of the Galaxy. The exact amount of gas that this structure contains is uncertain because of weak constrains in its distance. In this study, we made seven pointed Hα observations using the Wisconsin Hα Mapper Telescope and then compared the Hα intensity we obtained to models of the anticipated ionizing flux from the Milky Way and extragalactic background. From this, we calculated the distance from the Sun to the Leading Arm of the Magellanic System at the locations of our observations.

Apical Extrusion of Debris after Canal Preparation with Hand-Files Used Manually or Installed on Reciprocating Air-Driven Handpiece in Straight and Curved Canals.

PubMed

Labbaf, Hossein; Shakeri, Leila; Orduie, Reza; Bastami, Farshid

2015-01-01

Apical debris extrusion (DE) subsequent to root canal instrumentation, is one of the most important causes of endodontic flare-ups. The aim of this study was to compare the amount of DE after root canal instrumentation using nickel-titanium (NiTi) hand files with step-back manual technique or installed on reciprocating handpiece. This study was conducted on mesiobuccal (MB) roots of extracted maxillary first molars (n=20) and roots of mandibular premolars (n=20) that were randomly divided into two groups (n=20) according to the armamentarium used for canal preparation (air-driven reciprocating handpiece or hand instrumentation). In each group, the MB and premolar roots were prepared with the main apical sizes of 35 and 40, respectively. The extruded debris were collected and weighed. Finally, the mean dry weights were compared using ANOVA and t-test, and Tukey's Multiple Comparisons Procedures were used to determine the significant differences in amounts of DE. The level of significance was set at 0.05. Regardless of the type of teeth, the mean values of DE, were significantly lower in the handpiece group (P<0.0001). In addition, significantly lower amounts of DE was observed in premolars in similar group (P<0.001). However, this difference was not significant in MB roots of molars (P=0.20). Root canal preparation with reciprocating handpiece can lead to significantly lower debris extrusion than the manual step-back technique. In handpiece-prepared canals, the amount of extruded debris was significantly lower in premolar teeth.

The Pathology of Orthopedic Implant Failure Is Mediated by Innate Immune System Cytokines

PubMed Central

Landgraeber, Stefan; Jäger, Marcus; Jacobs, Joshua J.; Hallab, Nadim James

2014-01-01

All of the over 1 million total joint replacements implanted in the US each year are expected to eventually fail after 15–25 years of use, due to slow progressive subtle inflammation at the bone implant interface. This inflammatory disease state is caused by implant debris acting, primarily, on innate immune cells, that is, macrophages. This slow progressive pathological bone loss or “aseptic loosening” is a potentially life-threatening condition due to the serious complications in older people (>75 yrs) of total joint replacement revision surgery. In some people implant debris (particles and ions from metals) can influence the adaptive immune system as well, giving rise to the concept of metal sensitivity. However, a consensus of studies agrees that the dominant form of this response is due to innate reactivity by macrophages to implant debris where both danger (DAMP) and pathogen (PAMP) signalling elicit cytokine-based inflammatory responses. This paper discusses implant debris induced release of the cytokines and chemokines due to activation of the innate (and the adaptive) immune system and the subsequent formation of osteolysis. Different mechanisms of implant-debris reactivity related to the innate immune system are detailed, for example, danger signalling (e.g., IL-1β, IL-18, IL-33, etc.), toll-like receptor activation (e.g., IL-6, TNF-α, etc.), apoptosis (e.g., caspases 3–9), bone catabolism (e.g., TRAP5b), and hypoxia responses (Hif1-α). Cytokine-based clinical and basic science studies are in progress to provide diagnosis and therapeutic intervention strategies. PMID:24891761

Predicting debris-flow initiation and run-out with a depth-averaged two-phase model and adaptive numerical methods

NASA Astrophysics Data System (ADS)

George, D. L.; Iverson, R. M.

2012-12-01

Numerically simulating debris-flow motion presents many challenges due to the complicated physics of flowing granular-fluid mixtures, the diversity of spatial scales (ranging from a characteristic particle size to the extent of the debris flow deposit), and the unpredictability of the flow domain prior to a simulation. Accurately predicting debris-flows requires models that are complex enough to represent the dominant effects of granular-fluid interaction, while remaining mathematically and computationally tractable. We have developed a two-phase depth-averaged mathematical model for debris-flow initiation and subsequent motion. Additionally, we have developed software that numerically solves the model equations efficiently on large domains. A unique feature of the mathematical model is that it includes the feedback between pore-fluid pressure and the evolution of the solid grain volume fraction, a process that regulates flow resistance. This feature endows the model with the ability to represent the transition from a stationary mass to a dynamic flow. With traditional approaches, slope stability analysis and flow simulation are treated separately, and the latter models are often initialized with force balances that are unrealistically far from equilibrium. Additionally, our new model relies on relatively few dimensionless parameters that are functions of well-known material properties constrained by physical data (eg. hydraulic permeability, pore-fluid viscosity, debris compressibility, Coulomb friction coefficient, etc.). We have developed numerical methods and software for accurately solving the model equations. By employing adaptive mesh refinement (AMR), the software can efficiently resolve an evolving debris flow as it advances through irregular topography, without needing terrain-fit computational meshes. The AMR algorithms utilize multiple levels of grid resolutions, so that computationally inexpensive coarse grids can be used where the flow is absent, and much higher resolution grids evolve with the flow. The reduction in computational cost, due to AMR, makes very large-scale problems tractable on personal computers. Model accuracy can be tested by comparison of numerical predictions and empirical data. These comparisons utilize controlled experiments conducted at the USGS debris-flow flume, which provide detailed data about flow mobilization and dynamics. Additionally, we have simulated historical large-scale debris flows, such as the (≈50 million m^3) debris flow that originated on Mt. Meager, British Columbia in 2010. This flow took a very complex route through highly variable topography and provides a valuable benchmark for testing. Maps of the debris flow deposit and data from seismic stations provide evidence regarding flow initiation, transit times and deposition. Our simulations reproduce many of the complex patterns of the event, such as run-out geometry and extent, and the large-scale nature of the flow and the complex topographical features demonstrate the utility of AMR in flow simulations.

Dancing with the stars: formation of the Fomalhaut triple system and its effect on the debris discs

NASA Astrophysics Data System (ADS)

Shannon, Andrew; Clarke, Cathie; Wyatt, Mark

2014-07-01

Fomalhaut is a triple system, with all components widely separated (˜105 au). Such widely separated binaries are thought to form during cluster dissolution, but that process is unlikely to form such a triple system. We explore an alternative scenario, where A and C form as a tighter binary from a single molecular cloud core (with semimajor axis ˜104 au), and B is captured during cluster dispersal. We use N-body simulations augmented with the Galactic tidal forces to show that such a system naturally evolves into a Fomalhaut-like system in about half of cases, on a time-scale compatible with the age of Fomalhaut. From initial non-interacting orbits, Galactic tides drive cycles in B's eccentricity that lead to a close encounter with C. After several close encounters, typically lasting tens of millions of years, one of the stars is ejected. The Fomalhaut-like case with both components at large separations is almost invariably a precursor to the ejection of one component, most commonly Fomalhaut C. By including circumstellar debris in a subset of the simulations, we also show that such an evolution usually does not disrupt the coherently eccentric debris disc around Fomalhaut A, and in some cases can even produce such a disc. We also find that the final eccentricity of the disc around A and the disc around C are correlated, which may indicate that the dynamics of the three stars stirred C's disc, explaining its unusual brightness.

Short wavelength abedo, contrasts and micro-organisms on Venus

NASA Astrophysics Data System (ADS)

Limaye, Sanjay; Słowik, Grzegorgz; Ansari, Arif; Smith, David; Mogul, Rakesh; Vaishampayan, Parag

2017-04-01

The decrease in the amount of sunlight reflected by Venus at wavelengths below 500 nm, and the presence of contrast features prominent at ultraviolet wavelengths (270 - 410 nm) are two properties of the Venus clouds that despite numerous attempts, remain unexplained. Additional uncertainties include why the contrasts exist at all, and why the substance responsible for the contrasts does not appear well mixed. Nearly a century after the ultraviolet contrasts were discovered using Earth-based photographs, the substance or mechanisms responsible for the lower albedo and contrast patterns are still unknown. Many physical and chemical explanations have been proposed, but none of the hypotheses explain decrease of albedo below 500 nm, the spectral dependence of contrasts, and plausible mechanisms for presence or transport of those substances - transport from surface if the absorber is a condensation nuclei or transformations if in dissolved form due to photochemistry and the observed rapid changes in the contrasts. Considering the ultraviolet absorption shown by some terrestrial microorganisms, we speculate whether airborne bacteria (indigenous or introduced through meteoritic impact debris transported from Earth) could explain the mysterious contrast or the absorption cloud features on Venus. Plumes of cloud-borne aeroplankton, analogous to phytoplankton in Earth's oceans which are in dense enough concentrations to be observed from space, may have evolved on Venus when the planet had liquid water on its early surface, eventually migrating to a habitable zone in the clouds 50-70 km above the inhospitably hot surface today.

Filling of Spirit Lake, Washington, May 18, 1980 to July 31, 1982

USGS Publications Warehouse

Meyer, William; Carpenter, Philip J.

1983-01-01

The rockslide/debris avalanche from the north face of Mount St. Helens that precipitated the volcano 's eruption on May 18, 1980 , blocked outflow from Spirit Lake, Washington. There has been no surface outflow since that time. From May 21, 1980, when the first measurement of lake level was made, to August 1, 1982, Spirit Lake has increased its volume from 122,800 acre-ft to 264 ,000 acre-ft, an increase of 115%. Lake level has risen approximately 54 ft during this period. Hydrologic and geologic properties of the debris dam are unknown, but the materials obviously are easily erodible. Steep walled channels up to 60 ft deep have been eroded into the dam and are extending headward toward the lowest points on the crest. In addition, it appears that the lower areas on the crest of the dam are underlain by ash cloud deposits of low density. Indications are that the debris dam could fail by headward erosion, by overtopping with rapid downcutting, or by ' piping ' and rapid erosion. Each type of failure can produce rapid release of stored lake water with very high discharge rates. On the basis of observed filling rates of the lake over the last two yr and precipitation records at four long-term, low altitude National Weather Service stations, it is expected that normal precipitation will fill the lake to the dam crest in December 1985. This estimate is also based on the assumption that loss of water from the lake by seepage continues at the present rate until December 1985. With normal precipitation during the coming yr (August 1982 through July 1983 the lake will fill to a level 50 ft below the lowest existing point on the crest of the debris dam, which is at 3,532 ft altitude. If precipitation exceeds normal by 1.5 times during this coming year, the lake level will be 40 ft below the 3 ,532-ft crest of the debris dam by the end of July 1983. This same lake level can be reached by the end of March 1983 if precipitation from October through March is twice the winter mean. (Author 's abstract)

Efficacy of Cotton Root Destruction and Winter Cover Crops for Suppression of Hoplolaimus columbus.

PubMed

Davis, R F; Baird, R E; McNeil, R D

2000-12-01

The efficacy of rye (Secale cereale) and wheat (Triticum aestivum) winter cover crops and cotton stalk and root destruction (i.e., pulling them up) were evaluated in field tests during two growing seasons for Hoplolaimus columbus management in cotton. The effect of removing debris from the field following root destruction also was evaluated. Wheat and rye produced similar amounts of biomass, and both crops produced more biomass (P

Efficacy of Cotton Root Destruction and Winter Cover Crops for Suppression of Hoplolaimus columbus

PubMed Central

Davis, R. F.; Baird, R. E.; McNeil, R. D.

2000-01-01

The efficacy of rye (Secale cereale) and wheat (Triticum aestivum) winter cover crops and cotton stalk and root destruction (i.e., pulling them up) were evaluated in field tests during two growing seasons for Hoplolaimus columbus management in cotton. The effect of removing debris from the field following root destruction also was evaluated. Wheat and rye produced similar amounts of biomass, and both crops produced more biomass (P ≤ 0.05) following cotton root destruction. Cover crops did not suppress H. columbus population levels or increase subsequent cotton yields. Cotton root destruction did not affect cotton stand or plant height the following year. Cotton root destruction lowered (P ≤ 0.05) H. columbus population levels at planting in 1996 but not in 1997, but cotton yield was not increased by root destruction in either year. Removing debris following root destruction did not lower H. columbus levels compared to leaving debris on the soil surface. This study suggests that a rye or wheat cover crop or cotton root destruction following harvest is ineffective for H. columbus management in cotton. PMID:19271009

Determinations of cloud liquid water in the tropics from the SSM/I

NASA Technical Reports Server (NTRS)

Alishouse, John C.; Swift, Calvin; Ruf, Christopher; Snyder, Sheila; Vongsathorn, Jennifer

1989-01-01

Upward-looking microwave radiometric observations were used to validate the SSM/I determinations, and also as a basis for the determination of new coefficients. Due to insufficiency of the initial four channel algorithm for cloud liquid water, the improved algorithm was derived from the CORRAD (the University of Massachusetts autocorrelation radiometer) measurements of cloud liquid water and the matching SSM/I brightness temperatures using the standard linear regression. The correlation coefficients for the possible four channel combinations, and subsequently the best and the worst combinations were determined.

Observation of Upper and Middle Tropospheric Clouds

NASA Technical Reports Server (NTRS)

Cox, Stephen K.

1996-01-01

The goal of this research has been to identify and describe the properties of climatically important cloud systems critically important to understanding their effects upon satellite remote sensing and the global climate. These goals have been pursued along several different but complementary lines of investigation: the design, construction, testing and application of instrumentation; the collection of data sets during Intensive Field Observation periods; the reduction and analysis of data collected during IFO's; and completion of research projects specifically designed to address important and timely research objectives. In the first year covered by this research proposal, three papers were authored in the refereed literature which reported completed analyses of FIRE 1 IFO studies initiated under the previous NASA funding of this topic area. microphysical and radiative properties of marine stratocumulus cloud systems deduced from tethered balloon observations were reported from the San Nicolas Island site of the first FIRE marine stratocumulus experiment. Likewise, in situ observations of radiation and dynamic properties of a cirrus cloud layer were reported from first FIRE cirrus IFO based from Madison, Wisconsin. In addition, application techniques were under development for monitoring cirrus cloud systems using a 403 MHz Doppler wind profiler system adapted with a RASS (Radio Acoustic Sounding System) and an infrared interferometer system; these instrument systems were used in subsequent deployments for the FIRE 2 Parsons, Kansas and FIRE 2 Porto Santo, ASTEX expeditions. In November 1991 and in June 1992, these two systems along with a complete complement of surface radiation and meteorology measurements were deployed to the two sites noted above as anchor points for the respective IFO'S. Subsequent research activity concentrated on the interpretation and integration of the IFO analyses in the context of the radiative properties of cloud systems and our ability to remotely observe radiative, thermodynamic and dynamic properties of these cloud systems.

The Application of a Cloud-Based Student, Teacher, and Parent Platform in English as a Foreign Language Education

ERIC Educational Resources Information Center

Chiu, Fu-Yuan

2014-01-01

This study constructed a cloud-based student, teacher, and parent platform (CSTPP) in collaboration with a Taiwanese textbook publisher. Junior high school students' attitudes to learning English using the developed system were subsequently examined. The study participants were divided into 3 groups: Those in Group A employed the CSTPP with…

Nuclear winter - Global consequences of multiple nuclear explosions

NASA Technical Reports Server (NTRS)

Turco, R. P.; Toon, O. B.; Ackerman, T. P.; Pollack, J. B.; Sagan, C.

1983-01-01

The results of a computerized simulation of the potential global environmental effects of dust and smoke clouds that would be generated by a nuclear war are presented. Short term effects of blast, fire, and radiation are neglected in the series of physical models that include a nuclear war scenario, a particle microphysics model, and a radiative convective model. Account is taken of the altitude-dependent dust, smoke, radioactivity, and NO(x) injections, the temporal evolution of dust and smoke clouds, land and ocean environments, and temperature contrasts. A nuclear exchange would produce thousands of individual smoke and dust clouds rising up to 30 km altitude in the midlatitudes. The smoke, dust, and radioactive debris would cover the entire midlatitudes within 1-2 weeks. The smoke would arise from conflagrations of forests, suburbs, and urban areas. Obscuration of sunlight would induce subfreezing temperatures for several months, disruption of the global circulation patterns, and the arrival of a nuclear winter, followed and accompanied by radioactive fallout, pyrogenic air pollution, and UV-B flux enhancements. It is estimated that a total of only 100 Mtons would be sufficient to plunge the Northern Hemisphere summer to subfreezing temperatures lasting months. Since the probable exchange in a nuclear war would exceed 5000 Mtons, it is expected that many species, including humans, may not survive the war.

Characterization of soil and postlaunch pad debris from Cape Canaveral launch complex and analysis of soil interaction with aqueous HCl

NASA Technical Reports Server (NTRS)

Pellett, G. L.; Spangler, L. W.; Storey, R. W.; Bendura, R. J.

1982-01-01

Soil samples were fractionated and analyzed in order to assess the physical and chemical interactions of entrained soil with solid-rocket exhaust clouds. The sandy soil consisted primarily of quartz (silica) particles, 30 to 500 microns in diameter, and also contained seashell fragments. Differential and cumulative soil-mass size distributions are presented along with mineralogy, elemental compositions, and solution pH histories. About 90 percent of the soil mass consisted of particles 165 microns in diameter. Characteristic reaction times in aqueous HC1 slurries varied from a few minutes to several days, and capacities for reaction under acidic conditions varied from 10 to 40 g HCl/kg soil, depending on particle size. Airborne lifetimes of particles 165 microns are conservatively 30 min, and this major grouping is predicted to represent a small short-term chemical sink for up to 5% of the total HC1. The smaller and more minor fractions, below a 165 micron diameter, may act as giant cloud condensation nuclei over much longer airborne lifetimes. Finally, the demonstrated time dependency of neutralization is a complicating factor; it can influence the ability to deduce in-cloud HCl scavenging with reaction and can affect the accuracy of measured chemical compositions of near-field wet deposition.

The Detectability of Exo-Earths and Super-Earths via Resonant Signatures in Exozodiacal Clouds

NASA Technical Reports Server (NTRS)

Stark, Christopher C.; Kuchner, Marc

2008-01-01

Directly imaging extrasolar terrestrial planets necessarily means contending with the astrophysical noise of exozodiacal dust and the resonant structures created by these planets in exozodiacal clouds. Using a custom tailored hybrid symplectic integrator we have constructed 120 models of resonant structures created by exo-Earths and super-Earths on circular orbits interacting with collisionless steady-state dust clouds around a Sun-like star. Our models include enough particles to overcome the limitations of previous simulations that were often dominated by a handful of long-lived particles, allowing us to quantitatively study the contrast of the resulting ring structures. We found that in the case of a planet on a circular orbit, for a given star and dust source distribution, the morphology and contrast of the resonant structures depend on only two parameters: planet mass and (square root)ap/Beta, where ap is the planet's semi-major axis and Beta is the ratio of radiation pressure force to gravitational force on a grain. We constructed multiple-grain-size models of 25,000 particles each and showed that in a collisionless cloud, a Dohnanyi crushing law yields a resonant ring whose optical depth is dominated by the largest grains in the distribution, not the smallest. We used these models to estimate the mass of the lowest-mass planet that can be detected through observations of a resonant ring for a variety of assumptions about the dust cloud and the planet's orbit. Our simulations suggest that planets with mass as small as a few times Mars' mass may produce detectable signatures in debris disks at ap greater than or approximately equal to 10 AU.

Broadening of cloud droplet spectra through turbulent entrainment and eddy hopping

NASA Astrophysics Data System (ADS)

Abade, Gustavo; Grabowski, Wojciech; Pawlowska, Hanna

2017-11-01

This work discusses the effect of cloud turbulence and turbulent entrainment on the evolution of the cloud droplet-size spectrum. We simulate an ensemble of idealized turbulent cloud parcels that are subject to entrainment events, modeled as a random Poisson process. Entrainment events, subsequent turbulent mixing inside the parcel, supersaturation fluctuations, and the resulting stochastic droplet growth by condensation are simulated using a Monte Carlo scheme. Quantities characterizing the turbulence intensity, entrainment rate and the mean fraction of environmental air entrained in an event are specified as external parameters. Cloud microphysics is described by applying Lagrangian particles, the so-called superdroplets. They are either unactivated cloud condensation nuclei (CCN) or cloud droplets that form from activated CCN. The model accounts for the transport of environmental CCN into the cloud by the entraining eddies at the cloud edge. Turbulent mixing of the entrained dry air with cloudy air is described using a linear model. We show that turbulence plays an important role in aiding entrained CCN to activate, providing a source of small cloud droplets and thus broadening the droplet size distribution. Further simulation results will be reported at the meeting.

Cloud based intelligent system for delivering health care as a service.

PubMed

Kaur, Pankaj Deep; Chana, Inderveer

2014-01-01

The promising potential of cloud computing and its convergence with technologies such as mobile computing, wireless networks, sensor technologies allows for creation and delivery of newer type of cloud services. In this paper, we advocate the use of cloud computing for the creation and management of cloud based health care services. As a representative case study, we design a Cloud Based Intelligent Health Care Service (CBIHCS) that performs real time monitoring of user health data for diagnosis of chronic illness such as diabetes. Advance body sensor components are utilized to gather user specific health data and store in cloud based storage repositories for subsequent analysis and classification. In addition, infrastructure level mechanisms are proposed to provide dynamic resource elasticity for CBIHCS. Experimental results demonstrate that classification accuracy of 92.59% is achieved with our prototype system and the predicted patterns of CPU usage offer better opportunities for adaptive resource elasticity. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

Comparative evaluation of apically extruded debris during root canal instrumentation using two Ni-Ti single file rotary systems: An in vitro study

PubMed Central

Singbal, Kiran; Jain, Disha; Raja, Kranthi; Hoe, Tan Ming

2017-01-01

Background: Apical extrusion of debris during instrumentation is detrimental to the patient. Aim: The aim of this study was to evaluate the apical extrusion of debris during root canal instrumentation using two single file rotary Ni-Ti systems. Materials and Methods: Thirty freshly extracted mandibular premolars with straight roots were sterilized and divided into two groups instrumented using: One Shape rotary Ni-Ti system with Endoflare orifice shaper (Group 1) and Neo-Niti rotary Ni-Ti system with C1 orifice shaper (Group 2). Preweighed Eppendorf tubes fitted for each tooth before instrumentation. During instrumentation, 1 mL of distilled water with a 30-gauge needle was used to irrigate after every instrument. Tips of the tooth were irrigated with 2 ml distilled water after removal from Eppendorf tubes. The total volume of irrigant in each group was the same 8 ml. All tubes were incubated at 68°C for 15 days and subsequently weighed. The difference between pre- and post-debris weights was calculated, and statistical analysis was performed using independent t-test and level of significance was set at 0.05. Results: The difference between pre- and post-weights was significantly greater for the One Shape system. Conclusions: The Neolix Niti single file was associated with less extrusion compared to One Shape single file system. PMID:28855748

Comparative evaluation of apically extruded debris during root canal instrumentation using two Ni-Ti single file rotary systems: An in vitro study.

PubMed

Singbal, Kiran; Jain, Disha; Raja, Kranthi; Hoe, Tan Ming

2017-01-01

Apical extrusion of debris during instrumentation is detrimental to the patient. The aim of this study was to evaluate the apical extrusion of debris during root canal instrumentation using two single file rotary Ni-Ti systems. Thirty freshly extracted mandibular premolars with straight roots were sterilized and divided into two groups instrumented using: One Shape rotary Ni-Ti system with Endoflare orifice shaper (Group 1) and Neo-Niti rotary Ni-Ti system with C1 orifice shaper (Group 2). Preweighed Eppendorf tubes fitted for each tooth before instrumentation. During instrumentation, 1 mL of distilled water with a 30-gauge needle was used to irrigate after every instrument. Tips of the tooth were irrigated with 2 ml distilled water after removal from Eppendorf tubes. The total volume of irrigant in each group was the same 8 ml. All tubes were incubated at 68°C for 15 days and subsequently weighed. The difference between pre- and post-debris weights was calculated, and statistical analysis was performed using independent t -test and level of significance was set at 0.05. The difference between pre- and post-weights was significantly greater for the One Shape system. The Neolix Niti single file was associated with less extrusion compared to One Shape single file system.

Multi-layered foil capture of micrometeoroids and orbital debris in low Earth orbit

NASA Astrophysics Data System (ADS)

Kearsley, A.; Graham, G.

Much of our knowledge concerning the sub-millimetre orbital debris population that poses a threat to orbiting satellites has been gleaned from examination of surfaces retrieved and subsequently analysed as part of post-flight investigations. The preservation of the hypervelocity impact-derived remnants located on these surfaces is very variable, whether of space debris or micrometeoroid origin. Whilst glass and metallic materials show highly visible impact craters when examined using optical and electron microscopes, complex mixing between the target material and the impacting particle may make unambiguous interpretation of the impactor origin difficult or impossible. Our recent detailed examination of selected multi-layered insulation (MLI) foils from the ISAS Space Flyer Unit (SFU), and our preliminary study of NASA's Trek blanket, exposed on the Mir station, show that these constructions have the potential to preserve abundant residue material of a quality sufficient for detailed analysis. Although there are still limitations on the recognition of certain sources of orbital debris, the foils complement the metal and glass substrates. We suggest that a purpose-built multi-layered foil structure may prove to be extremely effective for rapid collection and unambiguous analysis of impact- derived residues. Such a collector could be used an environmental monitor for ISS, as it would have low mass, high durability, easy deployment, recovery and storage, making it an economically viable and attractive option.

Probabilistic Structural Health Monitoring of the Orbiter Wing Leading Edge

NASA Technical Reports Server (NTRS)

Yap, Keng C.; Macias, Jesus; Kaouk, Mohamed; Gafka, Tammy L.; Kerr, Justin H.

2011-01-01

A structural health monitoring (SHM) system can contribute to the risk management of a structure operating under hazardous conditions. An example is the Wing Leading Edge Impact Detection System (WLEIDS) that monitors the debris hazards to the Space Shuttle Orbiter s Reinforced Carbon-Carbon (RCC) panels. Since Return-to-Flight (RTF) after the Columbia accident, WLEIDS was developed and subsequently deployed on board the Orbiter to detect ascent and on-orbit debris impacts, so as to support the assessment of wing leading edge structural integrity prior to Orbiter re-entry. As SHM is inherently an inverse problem, the analyses involved, including those performed for WLEIDS, tend to be associated with significant uncertainty. The use of probabilistic approaches to handle the uncertainty has resulted in the successful implementation of many development and application milestones.

Quantifying Diurnal Cloud Radiative Effects by Cloud Type in the Tropical Western Pacific

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burleyson, Casey D.; Long, Charles N.; Comstock, Jennifer M.

2015-06-01

Cloud radiative effects are examined using long-term datasets collected at the three Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) Climate Research Facilities in the tropical western Pacific. We quantify the surface radiation budget, cloud populations, and cloud radiative effects by partitioning the data by cloud type, time of day, and as a function of large scale modes of variability such as El Niño Southern Oscillation (ENSO) phase and wet/dry seasons at Darwin. The novel facet of our analysis is that we break aggregate cloud radiative effects down by cloud type across the diurnal cycle. The Nauru cloud populations andmore » subsequently the surface radiation budget are strongly impacted by ENSO variability whereas the cloud populations over Manus only shift slightly in response to changes in ENSO phase. The Darwin site exhibits large seasonal monsoon related variations. We show that while deeper convective clouds have a strong conditional influence on the radiation reaching the surface, their limited frequency reduces their aggregate radiative impact. The largest source of shortwave cloud radiative effects at all three sites comes from low clouds. We use the observations to demonstrate that potential model biases in the amplitude of the diurnal cycle and mean cloud frequency would lead to larger errors in the surface energy budget compared to biases in the timing of the diurnal cycle of cloud frequency. Our results provide solid benchmarks to evaluate model simulations of cloud radiative effects in the tropics.« less

A comparison of shock-cloud and wind-cloud interactions: effect of increased cloud density contrast on cloud evolution

NASA Astrophysics Data System (ADS)

Goldsmith, K. J. A.; Pittard, J. M.

2018-05-01

The similarities, or otherwise, of a shock or wind interacting with a cloud of density contrast χ = 10 were explored in a previous paper. Here, we investigate such interactions with clouds of higher density contrast. We compare the adiabatic hydrodynamic interaction of a Mach 10 shock with a spherical cloud of χ = 103 with that of a cloud embedded in a wind with identical parameters to the post-shock flow. We find that initially there are only minor morphological differences between the shock-cloud and wind-cloud interactions, compared to when χ = 10. However, once the transmitted shock exits the cloud, the development of a turbulent wake and fragmentation of the cloud differs between the two simulations. On increasing the wind Mach number, we note the development of a thin, smooth tail of cloud material, which is then disrupted by the fragmentation of the cloud core and subsequent `mass-loading' of the flow. We find that the normalized cloud mixing time (tmix) is shorter at higher χ. However, a strong Mach number dependence on tmix and the normalized cloud drag time, t_{drag}^' }, is not observed. Mach-number-dependent values of tmix and t_{drag}^' } from comparable shock-cloud interactions converge towards the Mach-number-independent time-scales of the wind-cloud simulations. We find that high χ clouds can be accelerated up to 80-90 per cent of the wind velocity and travel large distances before being significantly mixed. However, complete mixing is not achieved in our simulations and at late times the flow remains perturbed.

The effects of forest residual debris disposal on perennial grass emergence, growth, and survival in a ponderosa pine ecotone

Treesearch

Darin J. Law; Peter F. Kolb

2007-01-01

Soil surface conditions can have profound effects on plant seedling emergence and subsequent seedling survival. To test the hypothesis that different soil-surface treatments with logging residue affect range grass seedling emergence and survival, 6 alternative forest-residual treatments were established in the summer of 1998 following thinning of mature trees from...

Aircraft-Induced Hole Punch and Canal Clouds

NASA Astrophysics Data System (ADS)

Heymsfield, A. J.; Kennedy, P.; Massie, S. T.; Schmitt, C. G.; Wang, Z.; Haimov, S.; Rangno, A.

2009-12-01

The production of holes and channels in altocumulus clouds by two commercial turboprop aircraft is documented for the first time. An unprecedented data set combining in situ measurements from microphysical probes with remote sensing measurements from cloud radar and lidar, all operating from the NSF/NCAR C130 aircraft, as well as ground-based NOAA and CSU radars, is used to describe the radar/lidar properties of a hole punch cloud and channel and the ensuing ice microphysical properties and structure of the ice column that subsequently developed. Ice particle production by commercial turboprop aircraft climbing through clouds much warmer than the regions where contrails are produced has the potential to modify significantly the cloud microphysical properties and effectively seed them under some conditions. Jet aircraft may also be producing hole punch clouds when flying through altocumulus with supercooled droplets at heights lower than their normal cruise altitudes where contrails can form. Commercial aircraft therefore can generate ice and affect the clouds at temperatures as much as 30°C warmer than the -40°C contrail formation threshold temperature.

Optical nucleation of bubble clouds in a high pressure spherical resonator.

PubMed

Anderson, Phillip; Sampathkumar, A; Murray, Todd W; Gaitan, D Felipe; Glynn Holt, R

2011-11-01

An experimental setup for nucleating clouds of bubbles in a high-pressure spherical resonator is described. Using nanosecond laser pulses and multiple phase gratings, bubble clouds are optically nucleated in an acoustic field. Dynamics of the clouds are captured using a high-speed CCD camera. The images reveal cloud nucleation, growth, and collapse and the resulting emission of radially expanding shockwaves. These shockwaves are reflected at the interior surface of the resonator and then reconverge to the center of the resonator. As the shocks reconverge upon the center of the resonator, they renucleate and grow the bubble cloud. This process is repeated over many acoustic cycles and with each successive shock reconvergence, the bubble cloud becomes more organized and centralized so that subsequent collapses give rise to stronger, better defined shockwaves. After many acoustic cycles individual bubbles cannot be distinguished and the cloud is then referred to as a cluster. Sustainability of the process is ultimately limited by the detuning of the acoustic field inside the resonator. The nucleation parameter space is studied in terms of laser firing phase, laser energy, and acoustic power used.

Mechanism of shallow disrupted slide induced by extreme rainfall

NASA Astrophysics Data System (ADS)

Igwe, O.; Fukuoka, H.

2010-12-01

On July 16, 2010, extreme rainfall attacked western Japan and it caused very intense rainfall in Shobara city, Hiroshima prefecture, Japan. This rainfall induced hundreds of shallow disrupted slides and many of those became debris flows. One of this debris flows attacked a house standing in front of the exit of a channel, and claimed a resident’s life. Western Japan had repeatedly similar disasters in the past. Last event took place from July 19 to 26, 2009, when western Japan had a severe rainstorms and caused floods and landslides. Most of the landslides are debris slide - debris flows. Most devastated case took place in Hofu city, Japan. On July 21, extremely intense rainstorm caused numerous debris flows and mud flows in the hillslopes. Some of the debris flows destroyed residential houses and home for elderly people, and finally killed 14 residents. One of the unusual feature of both disaster was that landslides are distributed in very narrow area. In the 2010 Shobara city disaster, all of the landslides were distributed in 5 km x 3 km, and in the 2009 Hofu city disaster, most devastated zone of landslides were 10 km x 5 km. Rain radars of Meteorological Agency of Government of Japan detected the intense rainfall, however, the spatial resolution is usually larger than 5 km and the disaster area is too small to predict landslides nor issue warning. Furthermore, it was found that the growth rate of baby clouds was very quick. The geology of both areas are rhyolite (Shobara) and granite (Hofu), so the areal assessment of landslide hazard should be prepared before those intense rainfall will come. As for the Hofu city case, it was proved that debris flows took place in the high precipitation area and covered by covered by weathered granite sands and silts which is called “masa". This sands has been proved susceptible against landslides under extreme rainfall conditions. However, the transition from slide - debris flow process is not well revealed, except authors past experiment on the similar masa samples in June 1999 Hiroshima debris flow case. Authors have embedded pore pressure control system for the undrained ring shear apparatus. Strongly weathered sandy soils were sampled just on the smooth and flat granitic sliding surface of one of the upstream small-scale landslides. Those contained finer grains and lower permeability rather than the one sampled in the Hiroshima case. Sample was consolidated by smaller stress corresponding to the site condition, and saturated by overnight circulating de-aired water. Normal stress and shear stress corresponding the slope condition was given, then, pore pressure (back pressure) was raised artificially at constant rate. When the effective stress reached the failure line, suddenly measured pore pressure monitored at about 2 mm above the shear plane, quickly increased. This sudden change abruptly accelerate the shear displacement. Stress condition soon reached the steady state and remained there thereafter. The reason of the excess pore pressure generation was the negative dilatancy, following a slight positive dilatancy. Most of the negative dilatancy could be explained by collapse of loose soil skelton as well as grain crushing during deformation and shearing.

Coupled prediction of flood response and debris flow initiation during warm- and cold-season events in the Southern Appalachians, USA

NASA Astrophysics Data System (ADS)

Tao, J.; Barros, A. P.

2014-01-01

Debris flows associated with rainstorms are a frequent and devastating hazard in the Southern Appalachians in the United States. Whereas warm-season events are clearly associated with heavy rainfall intensity, the same cannot be said for the cold-season events. Instead, there is a relationship between large (cumulative) rainfall events independently of season, and thus hydrometeorological regime, and debris flows. This suggests that the dynamics of subsurface hydrologic processes play an important role as a trigger mechanism, specifically through soil moisture redistribution by interflow. We further hypothesize that the transient mass fluxes associated with the temporal-spatial dynamics of interflow govern the timing of shallow landslide initiation, and subsequent debris flow mobilization. The first objective of this study is to investigate this relationship. The second objective is to assess the physical basis for a regional coupled flood prediction and debris flow warning system. For this purpose, uncalibrated model simulations of well-documented debris flows in headwater catchments of the Southern Appalachians using a 3-D surface-groundwater hydrologic model coupled with slope stability models are examined in detail. Specifically, we focus on two vulnerable headwater catchments that experience frequent debris flows, the Big Creek and the Jonathan Creek in the Upper Pigeon River Basin, North Carolina, and three distinct weather systems: an extremely heavy summertime convective storm in 2011; a persistent winter storm lasting several days; and a severe winter storm in 2009. These events were selected due to the optimal availability of rainfall observations; availability of detailed field surveys of the landslides shortly after they occurred, which can be used to evaluate model predictions; and because they are representative of events that cause major economic losses in the region. The model results substantiate that interflow is a useful prognostic of conditions necessary for the initiation of slope instability, and should therefore be considered explicitly in landslide hazard assessments. Moreover, the relationships between slope stability and interflow are strongly modulated by the topography and catchment-specific geomorphologic features that determine subsurface flow convergence zones. The three case studies demonstrate the value of coupled prediction of flood response and debris flow initiation potential in the context of developing a regional hazard warning system.

RS-34 (Peacekeeper Post Boost Propulsion System) Orbital Debris Application Concept Study

NASA Technical Reports Server (NTRS)

Esther, Elizabeth A.; Burnside, Christopher G.

2013-01-01

The Advanced Concepts Office (ACO) at the NASA Marshall Space Flight Center (MSFC) lead a study to evaluate the Rocketdyne produced RS-34 propulsion system as it applies to an orbital debris removal design reference mission. The existing RS-34 propulsion system is a remaining asset from the de-commissioned United States Air Force Peacekeeper ICBM program; specifically the pressure-fed storable bi-propellant Stage IV Post Boost Propulsion System. MSFC gained experience with the RS-34 propulsion system on the successful Ares I-X flight test program flown in the Ares I-X Roll control system (RoCS). The heritage hardware proved extremely robust and reliable and sparked interest for further utilization on other potential in-space applications. Subsequently, MSFC is working closely with the USAF to obtain all the remaining RS-34 stages for re-use opportunities. Prior to pursuit of securing the hardware, MSFC commissioned the Advanced Concepts Office to understand the capability and potential applications for the RS-34 Phoenix stage as it benefits NASA, DoD, and commercial industry. Originally designed, the RS-34 Phoenix provided in-space six-degrees-of freedom operational maneuvering to deploy multiple payloads at various orbital locations. The RS-34 Concept Study, preceded by a utilization study to understand how the unique capabilities of the RS-34 Phoenix and its application to six candidate missions, sought to further understand application for an orbital debris design reference mission as the orbital debris removal mission was found to closely mimic the heritage RS-34 mission. The RS-34 Orbital Debris Application Concept Study sought to identify multiple configurations varying the degree of modification to trade for dry mass optimization and propellant load for overall capability and evaluation of several candidate missions. The results of the RS-34 Phoenix Utilization Study show that the system is technically sufficient to successfully support all of the missions analyzed. The results and benefits of the RS-34 Orbital Debris Application Concept Study are presented in this paper.

Anatomy of an Asteroid Breakup

NASA Astrophysics Data System (ADS)

Kohler, Susanna

2017-05-01

A team of scientists has observed the breakup of an asteroid as it orbits the Sun. In a new study, they reveal what theyve learned from their ground- and space-based observations of this disintegration.These Hubble images show the fragments of R3 in higher resolution over the span of October 2013 to February 2014. [Jewitt et al. 2017]Observations of DisintegrationActive asteroids are objects that move on asteroid-like orbits while displaying comet-like behavior. The cause of their activity can vary ranging from outgassing as the asteroid heats up in its solar approach, to expelled debris from a collision, to the entire asteroid flying apart because its spinning too fast.Led by David Jewitt (University of California at Los Angeles), a team of scientists has analyzed observations of the disintegrating asteroid P/2013 R3. The observations span two years and were made by a number of telescopes, including Hubble, Keck (in Hawaii), Magellan (in Chile), and the Very Large Telescope (in Chile).A schematic diagram of the different fragments of R3 and how they relate to each other. Black numbers estimate the fragment separation velocities; red numbers estimate the separation date. [Jewitt et al. 2017]Jewitt and collaborators then used these observations and a bit of modeling to understand what asteroid R3 was like originally, what its pieces are doing now, and what caused it to break up.Cause of the BreakupThe team found that P/2013 R3 broke up into at least 13 pieces, the biggest of which was likely no more than 100-200 meters in size. The original asteroid was probably less than 400 m in radius.By measuring the velocities of the fragments in the various observations, Jewitt and collaborators were able to work backward to determine when each piece broke off. They found that the fragmentation process was spread out over the span of roughly 5 months suggesting that the asteroids breakup wasnt impact-related (otherwise the fragmentation would likely have been all at once rather than gradual).Timeline of the destruction of R3. Calendar dates are in black, day-of-year dates are in red. The letters below the timeline indicate observations. [Jewitt et al. 2017]So if it wasnt an impact, what caused the breakup of R3? Tidal stresses are unlikely; the asteroid wasnt close enough to the Sun or a planet to experience strong pulls. Gas pressure from sublimating ice also falls short of being strong enough to have caused the disruption, according to the authors calculations.The authors conclude that the most plausible cause of R3s breakup was rotational instability. If an asteroid is made up of a collection of rocky material loosely gravitationally bound in whats known as a rubble-pile composition, then it tends to fly apart if the asteroid spins faster than once every 2.2 hours. The authors show that torques from radiation or anisotropic sublimation could have driven R3 to spin this quickly on a relatively short timescale.A Dusty EndZodiacal light, caused by scattering by dust in the Zodiacal Cloud. [ESO]Lastly, Jewitt and collaborators examine the debris cloud released by the breakup of R3. They use these observations to estimate how much debris disrupted asteroids likely contribute to the Zodiacal Cloud, the cloud of dust found in our solar system, primarily between the Sun and Jupiter.The authors estimate that the fractional contribution by asteroids like R3 is roughly 4% consistent with models that suggest that asteroid dust is a measurable, but not dominant, contributor to the Zodiacal Cloud. Future sky surveys will allow us to better examine this contribution.CitationDavid Jewitt et al 2017 AJ 153 223. doi:10.3847/1538-3881/aa6a57

Sedimentological processes in a scarp-controlled rocky shoreline to upper continental slope environment, as revealed by unusual sedimentary features in the Neogene Coquimbo Formation, north-central Chile

NASA Astrophysics Data System (ADS)

Le Roux, J. P.; Gómez, Carolina; Fenner, Juliane; Middleton, Heather

2004-03-01

Exceptionally good outcrops of Miocene to Pliocene deposits in the vicinity of submarine Paleozoic basement scarps at Carrizalillo, north of La Serena, reveal a wealth of sedimentary features not commonly observed. The most proximal facies consist of rock fall and coarse-grained debris flow deposits directly abutting the basement wall from which they originated. Angular basement clasts are mixed with well-rounded cobbles, which probably formed as a basal gravel on a wave-cut platform at the beginning of marine flooding, subsequently accumulated at the scarp edge and were incorporated into the debris when the latter collapsed. The poor sorting, inverse grading, and protruding cobbles and boulders are classical debris flow features, with good clast imbrication indicating a laminar shearing action. A medial facies is represented by secondary channels running parallel to the major scarp about 1 km downslope of the first locality. In the largest channel, megaflutes at the base indicate the passage of highly turbulent, nondepositing flows eroding the soft, silty substrate. In the deepest, central part of the channel, a pebbly coquina shows horizontal and trough cross-stratification, with most of the bivalves oriented convex side up. Meter-scale rip-up clasts of the underlying siltstone are also present, indicating turbulent flow with a density sufficiently high to retard settling. The coquina is interpreted as a detachment deposit resulting from a hydroplaning debris flow along the central part of the channel, where the velocity and rate of pore pressure decay were highest. This deposit is overlain by fining upward, massive to horizontally stratified sandstone very similar in texture and composition to the matrix of the debris flow, suggesting its formation by surface transformation and elutriation of the latter. Along the channel margin, a basal centimeter-scale sandstone layer is virtually unaffected by the megaflute topography and clearly represents a subsequent event. It is interpreted as a basal shear carpet driven by the overlying debris flow. Within the shear carpet, a basal friction zone and an overlying collision zone containing a higher concentration of shell hash can be distinguished. The overlying debris flow deposit is represented by massive coquina with scattered, angular to rounded basement clasts. It contains disarticulated bivalves oriented with their concave side up, indicating large-scale upward fluid escape during deposition. A smaller secondary channel shows large rip-up rafts of the underlying substrate. Some rafts appear to have been plucked from the substrate by a process of sand injection from an overriding high-density sandy debris flow, which probably originated during a tsunami. Such clasts can climb upward into a laminar flow by down-current tilting and tumbling. The most distal facies occurs below a second scarp oriented more or less parallel to the present coastline, where finer-grained turbidites onlap and backlap onto the stoss and lee sides of an obstacle formed by eroded boulder conglomerates. The onlap deposits resemble inclined sandy macroforms recently described in submarine canyon settings. They are interbedded with diatom-containing, volcanic ash beds with cross-stratification dipping eastwards and containing deepwater microflora typical of continental upwelling zones.

Development of Multi-Sensor Global Cloud and Radiance Composites for DSCOVR EPIC Imager with Subpixel Definition

NASA Astrophysics Data System (ADS)

Khlopenkov, K. V.; Duda, D. P.; Thieman, M. M.; Sun-Mack, S.; Su, W.; Minnis, P.; Bedka, K. M.

2017-12-01

The Deep Space Climate Observatory (DSCOVR) is designed to study the daytime Earth radiation budget by means of onboard Earth Polychromatic Imaging Camera (EPIC) and National Institute of Standards and Technology Advanced Radiometer (NISTAR). EPIC imager observes in several shortwave bands (317-780 nm), while NISTAR measures the top-of-atmosphere (TOA) whole-disk radiance in shortwave and total broadband windows. Calculation of albedo and outgoing longwave flux requires a high-resolution scene identification such as the radiance observations and cloud property retrievals from low earth orbit and geostationary satellite imagers. These properties have to be co-located with EPIC imager pixels to provide scene identification and to select anisotropic directional models, which are then used to adjust the NISTAR-measured radiance and subsequently obtain the global daytime shortwave and longwave fluxes. This work presents an algorithm for optimal merging of selected radiances and cloud properties derived from multiple satellite imagers to obtain seamless global hourly composites at 5-km resolution. The highest quality observation is selected by means of an aggregated rating which incorporates several factors such as the nearest time relative to EPIC observation, lowest viewing zenith angle, and others. This process provides a smoother transition and avoids abrupt changes in the merged composite data. Higher spatial accuracy in the composite product is achieved by using the inverse mapping with gradient search during reprojection and bicubic interpolation for pixel resampling. The composite data are subsequently remapped into the EPIC-view domain by convolving composite pixels with the EPIC point spread function (PSF) defined with a half-pixel accuracy. Within every EPIC footprint, the PSF-weighted average radiances and cloud properties are computed for each cloud phase and then stored within five data subsets (clear-sky, water cloud, ice cloud, total cloud, and no retrieval). Overall, the composite product has been generated for every EPIC observation from June 2015 to December 2016, typically 300-500 composites per month, which makes it useful for many climate applications.

The use of remote sensing for rapid post-disaster assessment - an example from Kedarnath, Uttarakhand, north India (Invited)

NASA Astrophysics Data System (ADS)

Petley, D. N.

2013-12-01

Kedarnath is small town built around in important Hindu temple in the Rudraprayag district, Uttarakhand in northern India. Located at an elevation of 3,583 m, it is situated in a remote valley with no vehicular access. In summer, the temple is an important pilgrimage destination, with thousands of visitors per day, all of whom have to access the location via a 14 km trek or horse ride along a paved pathway, or via a helicopter ride. Between 14th and 17th June 2013, Uttarakhand was affected by unusually heavy early monsoonal rainfall. Whilst the rainfall totals did not reach record levels, the precipitation fell onto thawing snow, inducing very large debris flows. Kedarnath was affected by two major debris flows. According to eyewitness reports the first struck without warning in the evening of 16th June at about 7 pm local time. The second, larger, event occurred the following morning at about 6 am. The two debris flows destroyed most of the buildings in Kedarnath, although the temple survived with some damage. Across Uttarakhand it is estimated that about 5700 people died in the debris flows; the majority of these losses were at Kedarnath and in the immediate downstream communities. In the aftermath of the disaster there was considerable uncertainty as to the cause of the debris flows, with much speculation about the possibility that either a rock avalanche had developed on the flanks of the adjacent mountains or that there had been a catastrophic glacial collapse event upstream of the town. On 18th June the Indian Remote Sensing Organisation (IRSO) captured and released a RISAT-1 image of Kedarnath. Although the resolution was insufficient to determine what had occurred to trigger the disaster, it served to highlight two potential sources of the debris flows. One of these was an area of disturbance at the snout of the Charobari Glacier upslope from the town; the other was a possible landslide scar on an adjacent slope. On 23rd June 2013 NASA captured a Landsat 8 image of the site, which suggested that both of these sources might have been responsible for the debris flows. Finally, on 27th June IRSO released a high resolution RISAT-1 image of the Kedarnath region. This showed clearly that the first (16th June) debris flow originated from a landslide event upstream and to the east of the town. This took the form of an initially small, superficial landslide that entrained large volumes of debris before striking the town as a highly mobile debris flow. The second debris flow (on 17th June) was caused when an ephemeral lake, trapped behind a lateral moraine from the Charobari glacier upstream and to the east of the town, overtopped and catastrophically breached its barrier. The resultant flood scoured a large volume of sediment from the steep channel above the town, generating a very dense debris flow that was exceptionally destructive. Subsequent analyses by ground-based teams has suggested that this initial interpretation from remotely-sensed data was correct. Both of the sources of the debris flows were clearly evident on images captured before the event, and it is also clear that temple and the adjacent town were built on a terrace constructed in an earlier debris event. Thus, remotely sensed images could have played a role in the management of the hazard prior to the disaster.

Hazard assessment of landslide and debris flow in the Rjeina river valley, Croatia

NASA Astrophysics Data System (ADS)

Wang, Chunxiang; Watanabe, Naoki; Marui, Hideaki

2013-04-01

The Rječina River extends approximately 18.7km long and flows into the Adriatic Sea at the center of Rijeka City, Croatia. Landslide, debris flow and rockfall are main geohazards in the middle part of the Rječina river basin. The zone between the Valići reservoir dam and the Pasac Bridge is particularly the most unstable and hazardous area in the river basin. The Grohovo landslide in the middle part of the river basin is located on the valley's slope facing southwest and situated at just downstream of the Valići dam. This landslide is the largest active landslide along the Adriatic Sea coast in Croatia. Assuming that serious heavy rainfall or earthquake occurs, it is most likely to occur two types of geohazard event. One scenario is that the debris deposited on the Grohovo landslide will move down to the channel of the Rječina River and dam up the river course. Another scenario is that the slope deposits on the landslide will be mixed with water and subsequently turn into a debris flow reaching to Rijeka City. We simulate both two cases of the formation of landslide-dam and the occurrence of debris-flow by two integrated models using GIS to represent the dynamic process across 3D terrains. In the case of the formation of landslide-dam, it is assumed that slope deposits will move downhill after failing along a shear zone. GIS-based revised Hovland's 3D limit equilibrium model is used to simulate the movement and stoppage of the slope deposits to form landslide-dam. The 3D factor of safety will be calculated step by step during the sliding process simulation. Stoppage is defined by the factor of safety much greater than one and the velocity equal to zero. The simulation result shows that the height of the landslide-dam will be nine meters. In case of debris flow, the mixture of slope deposits and water will be differentiated from landslide by fluid-like deformation of the mobilized material. GIS-based depth-averaged 2D numerical model is used to predict the runout distance and inundated area of the debris flow. The simulation result displays the propagation and deposition of the debris flow across the complex topography and shows that the debris flow takes about 16 minutes to travel about 6 km along the Rječina River and consequently reaches to Rijeka City.

Formation of the Oort Cloud: Coupling Dynamical and Collisional Evolutions of Cometesimals

NASA Astrophysics Data System (ADS)

Charnoz, S.; Morbidelli, A.

2002-09-01

Cometesimals are thought to be born in the region of Giant Planets region and were subsequently ejected to the Oort Cloud by gravitational scattering. Some recent works (Stern & Weisman, 2001 Nature 409) have emphasized that during this phase of violent ejection, random velocities among cometesimals become so high that the majority of kilometer-sized comets might have been destroyed by multiple violent collisions before they reach the Oort Cloud, resulting in a low mass Oort Cloud. We present a new approach which allows to couple dynamical and collisional evolutions. This study focuses on cometesimals starting from the Jupiter-Saturn region. We find that the rapid depletion of the disk, due to the gravitational-scattering exerted by the giant planets, prevents a large fraction of cometesimals from rapid collisional destruction. These conclusions support the classical scenario of Oort Cloud formation.

The clouds of Venus. II - An investigation of the influence of coagulation on the observed droplet size distribution

NASA Technical Reports Server (NTRS)

Rossow, W. B.

1977-01-01

An approximate numerical technique is used to investigate the influence of coagulation, sedimentation and turbulent motions on the observed droplet size distribution in the upper layers of the Venus clouds. If the cloud mass mixing ratio is less than 0.000001 at 250 K or the eddy diffusivity throughout the cloud is greater than 1,000,000 sq cm per sec, then coagulation is unimportant. In this case, the observed droplet size distribution is the initial size distribution produced by the condensation of the droplets. It is found that all cloud models with droplet formation near the cloud top (e.g., a photochemical model) must produce the observed droplet size distribution by condensation without subsequent modification by coagulation. However, neither meteoritic or surface dust can supply sufficient nucleating particles to account for the observed droplet number density. If the cloud droplets are formed near the cloud bottom, the observed droplet size distribution can be produced solely by the interaction of coagulation and dynamics; all information about the initial size distribution is lost. If droplet formation occurs near the cloud bottom, the lower atmosphere of Venus is oxidizing rather than reducing.

Evaluating the Effects of Clouds on Solar and Longwave Radiation From Moored Buoys in the North Pacific

NASA Astrophysics Data System (ADS)

Balmes, K.; Cronin, M. F.

2014-12-01

Clouds play a critical role in the ocean surface radiation balance, along with the solar zenith angle and the atmospheric moisture and aerosol content. Two moored buoys in the North Pacific - KEO (32.3°N, 144.6°E) and Papa (50°N, 145°W) - continuously measure solar and longwave radiation and other atmospheric and oceanic variables through two redundant systems. After identifying the primary system and constructing daily clear sky solar and longwave radiation values, the seasonal and regional clouds effects are quantified for the two locations. Situated south of the Kuroshio Extension, significant moisture content variability, associated with the Asian monsoon, affects solar and longwave radiation and cloud effects at KEO. Less seasonal variability is observed at buoy Papa located in the Gulf of Alaska. At KEO, the negative solar radiation cloud forcing outweigh the positive longwave radiation cloud forcing leading to ocean cooling, particularly in the summer. At Papa, the longwave radiation cloud forcing counteracts the solar cloud forcing during the winter, subsequently warming the ocean. The regional and seasonal variability of clouds represents a difficult aspect of climate modeling and an area for further research.

Application of Seasonal CRM Integrations to Develop Statistics and Improved GCM Parameterization of Subgrid Cloud-Radiation Interactions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xiaoqing Wu; Xin-Zhong Liang; Sunwook Park

2007-01-23

The works supported by this ARM project lay the solid foundation for improving the parameterization of subgrid cloud-radiation interactions in the NCAR CCSM and the climate simulations. We have made a significant use of CRM simulations and concurrent ARM observations to produce long-term, consistent cloud and radiative property datasets at the cloud scale (Wu et al. 2006, 2007). With these datasets, we have investigated the mesoscale enhancement of cloud systems on surface heat fluxes (Wu and Guimond 2006), quantified the effects of cloud horizontal inhomogeneity and vertical overlap on the domain-averaged radiative fluxes (Wu and Liang 2005), and subsequently validatedmore » and improved the physically-based mosaic treatment of subgrid cloud-radiation interactions (Liang and Wu 2005). We have implemented the mosaic treatment into the CCM3. The 5-year (1979-1983) AMIP-type simulation showed significant impacts of subgrid cloud-radiation interaction on the climate simulations (Wu and Liang 2005). We have actively participated in CRM intercomparisons that foster the identification and physical understanding of common errors in cloud-scale modeling (Xie et al. 2005; Xu et al. 2005, Grabowski et al. 2005).« less

Energy dissipation by submarine obstacles during landslide impact on reservoir - potentially avoiding catastrophic dam collapse

NASA Astrophysics Data System (ADS)

Kafle, Jeevan; Kattel, Parameshwari; Mergili, Martin; Fischer, Jan-Thomas; Tuladhar, Bhadra Man; Pudasaini, Shiva P.

2017-04-01

Dense geophysical mass flows such as landslides, debris flows and debris avalanches may generate super tsunami waves as they impact water bodies such as the sea, hydraulic reservoirs or mountain lakes. Here, we apply a comprehensive and general two-phase, physical-mathematical mass flow model (Pudasaini, 2012) that consists of non-linear and hyperbolic-parabolic partial differential equations for mass and momentum balances, and present novel, high-resolution simulation results for two-phase flows, as a mixture of solid grains and viscous fluid, impacting fluid reservoirs with obstacles. The simulations demonstrate that due to the presence of different obstacles in the water body, the intense flow-obstacle-interaction dramatically reduces the flow momentum resulting in the rapid energy dissipation around the obstacles. With the increase of obstacle height overtopping decreases but, the deflection and capturing (holding) of solid mass increases. In addition, the submarine solid mass is captured by the multiple obstacles and the moving mass decreases both in amount and speed as each obstacle causes the flow to deflect into two streams and also captures a portion of it. This results in distinct tsunami and submarine flow dynamics with multiple surface water and submarine debris waves. This novel approach can be implemented in open source GIS modelling framework r.avaflow, and be applied in hazard mitigation, prevention and relevant engineering or environmental tasks. This might be in particular for process chains, such as debris impacts in lakes and subsequent overtopping. So, as the complex flow-obstacle-interactions strongly and simultaneously dissipate huge energy at impact such installations potentially avoid great threat against the integrity of the dam. References: Pudasaini, S. P. (2012): A general two-phase debris flow model. J. Geophys. Res. 117, F03010, doi: 10.1029/ 2011JF002186.

Apical Extrusion of Debris after Canal Preparation with Hand-Files Used Manually or Installed on Reciprocating Air-Driven Handpiece in Straight and Curved Canals

PubMed Central

Labbaf, Hossein; Shakeri, Leila; Orduie, Reza; Bastami, Farshid

2015-01-01

Introduction: Apical debris extrusion (DE) subsequent to root canal instrumentation, is one of the most important causes of endodontic flare-ups. The aim of this study was to compare the amount of DE after root canal instrumentation using nickel-titanium (NiTi) hand files with step-back manual technique or installed on reciprocating handpiece. Methods and Materials: This study was conducted on mesiobuccal (MB) roots of extracted maxillary first molars (n=20) and roots of mandibular premolars (n=20) that were randomly divided into two groups (n=20) according to the armamentarium used for canal preparation (air-driven reciprocating handpiece or hand instrumentation). In each group, the MB and premolar roots were prepared with the main apical sizes of 35 and 40, respectively. The extruded debris were collected and weighed. Finally, the mean dry weights were compared using ANOVA and t-test, and Tukey’s Multiple Comparisons Procedures were used to determine the significant differences in amounts of DE. The level of significance was set at 0.05. Results: Regardless of the type of teeth, the mean values of DE, were significantly lower in the handpiece group (P<0.0001). In addition, significantly lower amounts of DE was observed in premolars in similar group (P<0.001). However, this difference was not significant in MB roots of molars (P=0.20). Conclusion: Root canal preparation with reciprocating handpiece can lead to significantly lower debris extrusion than the manual step-back technique. In handpiece-prepared canals, the amount of extruded debris was significantly lower in premolar teeth. PMID:26213538

Monitoring of Wind Turbine Gearbox Condition through Oil and Wear Debris Analysis: A Full-Scale Testing Perspective

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sheng, Shuangwen

Despite the wind industry's dramatic development during the past decade, it is still challenged by premature turbine subsystem/component failures, especially for turbines rated above 1 MW. Because a crane is needed for each replacement, gearboxes have been a focal point for improvement in reliability and availability. Condition monitoring (CM) is a technique that can help improve these factors, leading to reduced turbine operation and maintenance costs and, subsequently, lower cost of energy for wind power. Although technical benefits of CM for the wind industry are normally recognized, there is a lack of published information on the advantages and limitations ofmore » each CM technique confirmed by objective data from full-scale tests. This article presents first-hand oil and wear debris analysis results obtained through tests that were based on full-scale wind turbine gearboxes rated at 750 kW. The tests were conducted at the 2.5-MW dynamometer test facility at the National Wind Technology Center at the National Renewable Energy Laboratory. The gearboxes were tested in three conditions: run-in, healthy, and damaged. The investigated CM techniques include real-time oil condition and wear debris monitoring, both inline and online sensors, and offline oil sample and wear debris analysis, both onsite and offsite laboratories. The reported results and observations help increase wind industry awareness of the benefits and limitations of oil and debris analysis technologies and highlight the challenges in these technologies and other tribological fields for the Society of Tribologists and Lubrication Engineers and other organizations to help address, leading to extended gearbox service life.« less

Climate influence on volcano edifice stability and fluvial landscape evolution surrounding Mount Ruapehu, New Zealand

NASA Astrophysics Data System (ADS)

Tost, M.; Cronin, S. J.

2016-06-01

Large volcanic debris avalanches are triggered by failure of the steep flanks of long-lived composite cones. Their huge deposits change the landscape and drainage pattern surrounding stratovolcanoes for thousands of years. At Mt. Ruapehu, New Zealand, we identified seven major flank-collapse events that produced debris avalanches travelling down pre-existing river catchments for up to 90 km from source. In two cases the extreme mass flux into the river valleys led to their complete truncation from the volcano, while four drainage systems were subsequently re-established along similar pathways influenced by regional strike-slip faulting, which caused localized graben formation. In all cases the volcanic debris-avalanche deposits currently form distinctive plateaus at or near the highest topographic elevations of each river valley margin. The timing of the flank failures indicate that inter-eruptive cone destabilization of Mt. Ruapehu is affected by climate change and occurs most commonly during interstadials when glaciers on the cone are in retreat, whereas syn-eruptive collapses are most prominent during cold stages. Dated debris-avalanche deposit levels, along with those of up to four stadial-related aggradational gravel terraces between c. 125 and 18 ka, were used to calculate regional uplift rates in this area. Rates of between 0.2 ± 0.1 mm yr- 1 to 3.8 ± 0.8 mm yr- 1 are found for four river systems dissecting the central North Island of New Zealand. In three cases incision below the diamicton sequences and into the basement, allowed quantification of sediment-flux rates into the Tasman Sea of 107,000 ± 1,200 m3 yr- 1 to 177,000 ± 3,500 m3 yr- 1 since debris-avalanche emplacement.

Long range laser propagation: power scaling and beam quality issues

NASA Astrophysics Data System (ADS)

Bohn, Willy L.

2010-09-01

This paper will address long range laser propagation applications where power and, in particular beam quality issues play a major role. Hereby the power level is defined by the specific mission under consideration. I restrict myself to the following application areas: (1)Remote sensing/Space based LIDAR, (2) Space debris removal (3)Energy transmission, and (4)Directed energy weapons Typical examples for space based LIDARs are the ADM Aeolus ESA mission using the ALADIN Nd:YAG laser with its third harmonic at 355 nm and the NASA 2 μm Tm:Ho:LuLiF convectively cooled solid state laser. Space debris removal has attracted more attention in the last years due to the dangerous accumulation of debris in orbit which become a threat to the satellites and the ISS space station. High power high brightness lasers may contribute to this problem by partially ablating the debris material and hence generating an impulse which will eventually de-orbit the debris with their subsequent disintegration in the lower atmosphere. Energy transmission via laser beam from space to earth has long been discussed as a novel long term approach to solve the energy problem on earth. In addition orbital transfer and stationkeeping are among the more mid-term applications of high power laser beams. Finally, directed energy weapons are becoming closer to reality as corresponding laser sources have matured due to recent efforts in the JHPSSL program. All of this can only be realized if he laser sources fulfill the necessary power requirements while keeping the beam quality as close as possible to the diffraction limited value. And this is the rationale and motivation of this paper.

The clinical implications of elevated blood metal ion concentrations in asymptomatic patients with MoM hip resurfacings: a cohort study

PubMed Central

Langton, David J; Sidaginamale, Raghavendra P; Joyce, Thomas J; Natu, Shonali; Blain, Peter; Jefferson, Robert Drysdale; Rushton, Stephen; Nargol, Antoni V F

2013-01-01

Objective To determine whether elevated blood cobalt (Co) concentrations are associated with early failure of metal-on-metal (MoM) hip resurfacings secondary to adverse reaction to metal debris (ARMD). Design Cohort study. Setting Single centre orthopaedic unit. Participants Following the identification of complications potentially related to metal wear debris, a blood metal ion screening programme was instigated at our unit in 2007 for all patients with Articular Surface Replacement (ASR) and Birmingham MoM hip resurfacings. Patients were followed annually unless symptoms presented earlier. Symptomatic patients were investigated with ultrasound scan and joint aspiration. The clinical course of all 278 patients with ‘no pain’ or ‘slight/occasional’ pain and a Harris Hip Score greater than or equal to 95 at the time of venesection were documented. A retrospective analysis was subsequently conducted using mixed effect modelling to investigate the temporal pattern of blood Co levels in the patients and survival analysis to investigate the potential role of case demographics and blood Co levels as risk factors for subsequent failure secondary to ARMD. Results Blood Co concentration was a positive and significant risk factor (z=8.44, p=2×10–16) for joint failure, as was the device, where the Birmingham Hip Resurfacing posed a significantly reduced risk for revision by 89% (z=−3.445, p=0.00005 (95% CI on risk 62 to 97)). Analysis using Cox-proportional hazards models indicated that men had a 66% lower risk of joint failure than women (z=−2.29419, p=0.0218, (95% CI on risk reduction 23 to 89)). Conclusions The results suggest that elevated blood metal ion concentrations are associated with early failure of MoM devices secondary to adverse reactions to metal debris. Co concentrations greater than 20 µg/l are frequently associated with metal staining of tissues and the development of osteolysis. Development of soft tissue damage appears to be more complex with females and patients with ASR devices seemingly more at risk when exposed to equivalent doses of metal debris. PMID:23482990

On the evolution of Saturn's 'Spokes' - Theory

NASA Technical Reports Server (NTRS)

Morfill, G. E.; Gruen, E.; Goertz, C. K.; Johnson, T. V.

1983-01-01

Starting with the assumption that negatively charged micron-sized dust grains may be elevated above Saturn's ring plane by plasma interactions, the subsequent evolution of the system is discussed. The discharge of the fine dust by solar UV radiation produces a cloud of electrons which moves adiabatically in Saturn's dipolar magnetic field. The electron cloud is absorbed by the ring after one bounce, alters the local ring potential significantly, and reduces the local Debye length. As a result, more micron-sized dust particles may be elevated above the ring plane and the spoke grows. This process continues until the electron cloud has dissipated.

The use of marine cloud water samples as a diagnostic tool for aqueous chemistry, cloud microphysical processes and dynamics

NASA Astrophysics Data System (ADS)

Crosbie, E.; Ziemba, L. D.; Moore, R.; Shook, M.; Jordan, C.; Thornhill, K. L., II; Winstead, E.; Shingler, T.; Brown, M.; MacDonald, A. B.; Dadashazar, H.; Sorooshian, A.; Weiss-Penzias, P. S.; Anderson, B.

2017-12-01

Clouds play several roles in the Earth's climate system. In addition to their clear significance to the hydrological cycle, they strongly modulate the shortwave and longwave radiative balance of the atmosphere, with subsequent feedback on the atmospheric circulation. Furthermore, clouds act as a conduit for the fate and emergence of important trace chemical species and are the predominant removal mechanism for atmospheric aerosols. Marine boundary layer clouds cover large swaths of the global oceans. Because of their global significance, they have attracted significant attention into understanding how changes in aerosols are translated into changes in cloud macro- and microphysical properties. The circular nature of the influence of clouds-on-aerosols and aerosols-on-clouds has been used to explain the chaotic patterns often seen in marine clouds, however, this feedback also presents a substantial hurdle in resolving the uncertain role of anthropogenic aerosols on climate. Here we discuss ways in which the chemical constituents found in cloud water can offer insight into the physical and chemical processes inherent in marine clouds, through the use of aircraft measurements. We focus on observational data from cloud water samples collected during flights conducted over the remote North Atlantic and along coastal California across multiple campaigns. We explore topics related to aqueous processing, wet scavenging and source apportionment.

Detection of long duration cloud contamination in hyper-temporal NDVI imagery

NASA Astrophysics Data System (ADS)

Ali, A.; de Bie, C. A. J. M.; Skidmore, A. K.; Scarrott, R. G.

2012-04-01

NDVI time series imagery are commonly used as a reliable source for land use and land cover mapping and monitoring. However long duration cloud can significantly influence its precision in areas where persistent clouds prevails. Therefore quantifying errors related to cloud contamination are essential for accurate land cover mapping and monitoring. This study aims to detect long duration cloud contamination in hyper-temporal NDVI imagery based land cover mapping and monitoring. MODIS-Terra NDVI imagery (250 m; 16-day; Feb'03-Dec'09) were used after necessary pre-processing using quality flags and upper envelope filter (ASAVOGOL). Subsequently stacked MODIS-Terra NDVI image (161 layers) was classified for 10 to 100 clusters using ISODATA. After classifications, 97 clusters image was selected as best classified with the help of divergence statistics. To detect long duration cloud contamination, mean NDVI class profiles of 97 clusters image was analyzed for temporal artifacts. Results showed that long duration clouds affect the normal temporal progression of NDVI and caused anomalies. Out of total 97 clusters, 32 clusters were found with cloud contamination. Cloud contamination was found more prominent in areas where high rainfall occurs. This study can help to stop error propagation in regional land cover mapping and monitoring, caused by long duration cloud contamination.

A bill to authorize the Administrator of the National Oceanic and Atmospheric Administration to provide certain funds to eligible entities for activities undertaken to address the marine debris impacts of the March 2011 Tohoku earthquake and subsequent tsunami, and for other purposes.

THOMAS, 113th Congress

Sen. Merkley, Jeff [D-OR

2013-06-13

Senate - 06/13/2013 Read twice and referred to the Committee on Commerce, Science, and Transportation. (All Actions) Tracker: This bill has the status IntroducedHere are the steps for Status of Legislation:

Learning by Teaching: Undergraduate Engineering Students Improving a Community's Response Capability to an Early Warning System

ERIC Educational Resources Information Center

Suvannatsiri, Ratchasak; Santichaianant, Kitidech; Murphy, Elizabeth

2015-01-01

This paper reports on a project in which students designed, constructed and tested a model of an existing early warning system with simulation of debris flow in a context of a landslide. Students also assessed rural community members' knowledge of this system and subsequently taught them to estimate the time needed for evacuation of the community…

To authorize the Administrator of the National Oceanic and Atmospheric Administration to provide certain funds to eligible entities for activities undertaken to address the marine debris impacts of the March 2011 Tohoku earthquake and subsequent tsunami, and for other purposes.

THOMAS, 113th Congress

Rep. Bonamici, Suzanne [D-OR-1

2013-04-11

House - 04/02/2014 Reported (Amended) by the Committee on Natural Resources. H. Rept. 113-399, Part I. (All Actions) Tracker: This bill has the status IntroducedHere are the steps for Status of Legislation:

Effect of pectin methylesterase on carrot (Daucus carota) juice cloud stability.

PubMed

Schultz, Alison K; Anthon, Gordon E; Dungan, Stephanie R; Barrett, Diane M

2014-02-05

To determine the effect of residual enzyme activity on carrot juice cloud, 0 to 1 U/g pectin methylesterase (PME) was added to pasteurized carrot juice. Cloud stability and particle diameters were measured to quantify juice cloud stability and clarification for 56 days of storage. All levels of PME addition resulted in clarification; higher amounts had a modest effect in causing more rapid clarification, due to a faster increase in particle size. The cloud initially exhibited a trimodal distribution of particle sizes. For enzyme-containing samples, particles in the smallest-sized mode initially aggregated to merge with the second peak over 5-10 days. This larger population then continued to aggregate more slowly over longer times. This observation of a more rapid destabilization process initially, followed by slower subsequent changes in the cloud, was also manifested in measurements of sedimentation extent and in turbidity tests. Optical microscopy showed that aggregation created elongated, fractal particle structures over time.

Dynamical States of Low Temperature Cirrus

NASA Technical Reports Server (NTRS)

Barahona, D.; Nenes, A.

2011-01-01

Low ice crystal concentration and sustained in-cloud supersaturation, commonly found in cloud observations at low temperature, challenge our understanding of cirrus formation. Heterogeneous freezing from effloresced ammonium sulfate, glassy aerosol, dust and black carbon are proposed to cause these phenomena; this requires low updrafts for cirrus characteristics to agree with observations and is at odds with the gravity wave spectrum in the upper troposphere. Background temperature fluctuations however can establish a dynamical equilibrium between ice production and sedimentation loss (as opposed to ice crystal formation during the first stages of cloud evolution and subsequent slow cloud decay) that explains low temperature cirrus properties. This newly-discovered state is favored at low temperatures and does not require heterogeneous nucleation to occur (the presence of ice nuclei can however facilitate its onset). Our understanding of cirrus clouds and their role in anthropogenic climate change is reshaped, as the type of dynamical forcing will set these clouds in one of two preferred microphysical regimes with very different susceptibility to aerosol.

HCl in rocket exhaust clouds - Atmospheric dispersion, acid aerosol characteristics, and acid rain deposition

NASA Technical Reports Server (NTRS)

Pellett, G. L.; Sebacher, D. I.; Bendura, R. J.; Wornom, D. E.

1983-01-01

Both measurements and model calculations of the temporal dispersion of peak HCl (g + aq) concentration in Titan III exhaust clouds are found to be well characterized by one-term power-law decay expressions. The respective coefficients and decay exponents, however, are found to vary widely with meteorology. The HCl (g), HCl (g + aq), dewpoint, and temperature-pressure-altitude data for Titan III exhaust clouds are consistent with accurately calculated HCl/H2O vapor-liquid compositions for a model quasi-equilibrated flat surface aqueous aerosol. Some cloud evolution characteristics are also defined. Rapid and extensive condensation of aqueous acid clearly occurs during the first three min of cloud rise. Condensation is found to be intensified by the initial entrainment of relatively moist ambient air from lower levels, that is, from levels below eventual cloud stabilization. It is pointed out that if subsequent dilution air at stabilization altitude is significantly drier, a state of maximum condensation soon occurs, followed by an aerosol evaporation phase.

A portable low-cost 3D point cloud acquiring method based on structure light

NASA Astrophysics Data System (ADS)

Gui, Li; Zheng, Shunyi; Huang, Xia; Zhao, Like; Ma, Hao; Ge, Chao; Tang, Qiuxia

2018-03-01

A fast and low-cost method of acquiring 3D point cloud data is proposed in this paper, which can solve the problems of lack of texture information and low efficiency of acquiring point cloud data with only one pair of cheap cameras and projector. Firstly, we put forward a scene adaptive design method of random encoding pattern, that is, a coding pattern is projected onto the target surface in order to form texture information, which is favorable for image matching. Subsequently, we design an efficient dense matching algorithm that fits the projected texture. After the optimization of global algorithm and multi-kernel parallel development with the fusion of hardware and software, a fast acquisition system of point-cloud data is accomplished. Through the evaluation of point cloud accuracy, the results show that point cloud acquired by the method proposed in this paper has higher precision. What`s more, the scanning speed meets the demand of dynamic occasion and has better practical application value.

Feature relevance assessment for the semantic interpretation of 3D point cloud data

NASA Astrophysics Data System (ADS)

Weinmann, M.; Jutzi, B.; Mallet, C.

2013-10-01

The automatic analysis of large 3D point clouds represents a crucial task in photogrammetry, remote sensing and computer vision. In this paper, we propose a new methodology for the semantic interpretation of such point clouds which involves feature relevance assessment in order to reduce both processing time and memory consumption. Given a standard benchmark dataset with 1.3 million 3D points, we first extract a set of 21 geometric 3D and 2D features. Subsequently, we apply a classifier-independent ranking procedure which involves a general relevance metric in order to derive compact and robust subsets of versatile features which are generally applicable for a large variety of subsequent tasks. This metric is based on 7 different feature selection strategies and thus addresses different intrinsic properties of the given data. For the example of semantically interpreting 3D point cloud data, we demonstrate the great potential of smaller subsets consisting of only the most relevant features with 4 different state-of-the-art classifiers. The results reveal that, instead of including as many features as possible in order to compensate for lack of knowledge, a crucial task such as scene interpretation can be carried out with only few versatile features and even improved accuracy.

The γ-ray afterglows of tidal disruption events

PubMed Central

Chen, Xian; Gómez-Vargas, Germán Arturo; Guillochon, James

2016-01-01

A star wandering too close to a supermassive black hole (SMBH) will be tidally disrupted. Previous studies of such ‘tidal disruption event’ (TDE) mostly focus on the stellar debris that are bound to the system, because they give rise to luminous flares. On the other hand, half of the stellar debris in principle are unbound and can stream to a great distance, but so far there is no clear evidence that this ‘unbound debris stream’ (UDS) exists. Motivated by the fact that the circum-nuclear region around SMBHs is usually filled with dense molecular clouds (MCs), here we investigate the observational signatures resulting from the collision between an UDS and an MC, which is likely to happen hundreds of years after a TDE. We focus on γ-ray emission (0.1–105 GeV), which comes from the encounter of shock-accelerated cosmic rays with background protons and, more importantly, is not subject to extinction. We show that because of the high proton density inside an MC, the peak γ-ray luminosity, about 1039 erg s−1, is at least 100 times greater than that in the case without an MC (only with a smooth interstellar medium). The luminosity decays on a time-scale of decades, depending on the distance of the MC, and about a dozen of these ‘TDE afterglows’ could be detected within a distance of about 16 Mpc by the future Cherenkov Telescope Array. Without careful discrimination, these sources potentially could contaminate the searches for starburst galaxies, galactic nuclei containing millisecond pulsars or dark matter annihilation signals. PMID:27453685

Cloud detection method for Chinese moderate high resolution satellite imagery (Conference Presentation)

NASA Astrophysics Data System (ADS)

Zhong, Bo; Chen, Wuhan; Wu, Shanlong; Liu, Qinhuo

2016-10-01

Cloud detection of satellite imagery is very important for quantitative remote sensing research and remote sensing applications. However, many satellite sensors don't have enough bands for a quick, accurate, and simple detection of clouds. Particularly, the newly launched moderate to high spatial resolution satellite sensors of China, such as the charge-coupled device on-board the Chinese Huan Jing 1 (HJ-1/CCD) and the wide field of view (WFV) sensor on-board the Gao Fen 1 (GF-1), only have four available bands including blue, green, red, and near infrared bands, which are far from the requirements of most could detection methods. In order to solve this problem, an improved and automated cloud detection method for Chinese satellite sensors called OCM (Object oriented Cloud and cloud-shadow Matching method) is presented in this paper. It firstly modified the Automatic Cloud Cover Assessment (ACCA) method, which was developed for Landsat-7 data, to get an initial cloud map. The modified ACCA method is mainly based on threshold and different threshold setting produces different cloud map. Subsequently, a strict threshold is used to produce a cloud map with high confidence and large amount of cloud omission and a loose threshold is used to produce a cloud map with low confidence and large amount of commission. Secondly, a corresponding cloud-shadow map is also produced using the threshold of near-infrared band. Thirdly, the cloud maps and cloud-shadow map are transferred to cloud objects and cloud-shadow objects. Cloud and cloud-shadow are usually in pairs; consequently, the final cloud and cloud-shadow maps are made based on the relationship between cloud and cloud-shadow objects. OCM method was tested using almost 200 HJ-1/CCD images across China and the overall accuracy of cloud detection is close to 90%.

CLOUD AND HAZE IN THE WINTER POLAR REGION OF TITAN OBSERVED WITH VISUAL AND INFRARED MAPPING SPECTROMETER ON BOARD CASSINI

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rannou, P.; Le Mouelic, S.; Sotin, C.

2012-03-20

A large cloud in the north polar region of Titan was first observed by the Visual and Infrared Mapping Spectrometer (VIMS) in 2005 and then in 2006. This cloud, confined beyond the latitude 62 Degree-Sign N, is surrounded by a mixture of aerosol and mist probably lying in the low stratosphere and troposphere. Subsequent images of this region of Titan show a gradual vanishing of this cloud which was reported previously. In this paper, we characterize the physical properties of this cloud, haze, and mist as well as their time evolutions. We note several details on the images such asmore » a secondary cloud above the main cloud and latitudes beyond 70 Degree-Sign N. We also show that the cloud disappearance leaves the polar region poorly loaded in aerosols, yielding an annular zone of aerosols between 50 Degree-Sign N and 65 Degree-Sign N. Our analysis suggests that this structure observed by VIMS in the near-IR is an annular structure observed by ISS on board Voyager one Titan year ago in 1980.« less

A Method to Estimate the Probability that any Individual Cloud-to-Ground Lightning Stroke was Within any Radius of any Point

NASA Technical Reports Server (NTRS)

Huddleston, Lisa L.; Roeder, William P.; Merceret, Francis J.

2011-01-01

A new technique has been developed to estimate the probability that a nearby cloud to ground lightning stroke was within a specified radius of any point of interest. This process uses the bivariate Gaussian distribution of probability density provided by the current lightning location error ellipse for the most likely location of a lightning stroke and integrates it to determine the probability that the stroke is inside any specified radius of any location, even if that location is not centered on or even with the location error ellipse. This technique is adapted from a method of calculating the probability of debris collision with spacecraft. Such a technique is important in spaceport processing activities because it allows engineers to quantify the risk of induced current damage to critical electronics due to nearby lightning strokes. This technique was tested extensively and is now in use by space launch organizations at Kennedy Space Center and Cape Canaveral Air Force Station. Future applications could include forensic meteorology.

The Impact of a Large Object on Jupiter in 2009 July

NASA Technical Reports Server (NTRS)

Sanchez-Lavega, A.; Wesley, A.; Orton, G.; Hueso, R.; Perez-Hoyos, S.; Fletcher, L. N.; Yanamandra-Fisher, P.; Legarreta, J.; de Pater, I.; Hammel, H.;

Spectroscopic follow-up of the Hercules-Aquila Cloud

NASA Astrophysics Data System (ADS)

Simion, Iulia T.; Belokurov, Vasily; Koposov, Sergey E.; Sheffield, Allyson; Johnston, Kathryn V.

2018-05-01

We designed a follow-up program to find the spectroscopic properties of the Hercules-Aquila Cloud (HAC) and test scenarios for its formation. We measured the radial velocities (RVs) of 45 RR Lyrae in the southern portion of the HAC using the facilities at the MDM observatory, producing the first large sample of velocities in the HAC. We found a double-peaked distribution in RVs, skewed slightly to negative velocities. We compared both the morphology of HAC projected on to the plane of the sky and the distribution of velocities in this structure outlined by RR Lyrae and other tracer populations at different distances to N-body simulations. We found that the behaviour is characteristic of an old, well-mixed accretion event with small apo-galactic radius. We cannot yet rule out other formation mechanisms for the HAC. However, if our interpretation is correct, HAC represents just a small portion of a much larger debris structure spread throughout the inner Galaxy whose distinct kinematic structure should be apparent in RV studies along many lines of sight.

A Method to Estimate the Probability that Any Individual Cloud-to-Ground Lightning Stroke was Within Any Radius of Any Point

NASA Technical Reports Server (NTRS)

Huddleston, Lisa; Roeder, WIlliam P.; Merceret, Francis J.

2011-01-01

A new technique has been developed to estimate the probability that a nearby cloud-to-ground lightning stroke was within a specified radius of any point of interest. This process uses the bivariate Gaussian distribution of probability density provided by the current lightning location error ellipse for the most likely location of a lightning stroke and integrates it to determine the probability that the stroke is inside any specified radius of any location, even if that location is not centered on or even within the location error ellipse. This technique is adapted from a method of calculating the probability of debris collision with spacecraft. Such a technique is important in spaceport processing activities because it allows engineers to quantify the risk of induced current damage to critical electronics due to nearby lightning strokes. This technique was tested extensively and is now in use by space launch organizations at Kennedy Space Center and Cape Canaveral Air Force station. Future applications could include forensic meteorology.

Bagley Fire Sediment Study: Shasta-Trinity National Forest, Eastern Klamath Mountains, Northern California

NASA Astrophysics Data System (ADS)

Bachmann, S.; De La Fuente, J. A.; Hill, B.; Mai, C.; Mikulovsky, R. P.; Mondry, Z.; Rust, B.; Young, D.

2013-12-01

The US Forest Service is conducting a study of sediment mobilization, transport, and deposition on the Bagley Fire, which burned about 18,000 hectares in late summer, 2012, on the Shasta-Trinity National Forest, south of McCloud, CA. The fire area is in steep terrain of the Eastern Klamath Mountains that are underlain primarily by metasedimentary rock. The watersheds affected drain into the headwaters of Squaw Creek, along with small streams tributary to the McCloud and Pit Rivers, all of which flow into Shasta Lake Reservoir. In November and December of 2012, intense storms occurred over the fire area with estimated return intervals of 25-50 years, based on 4-day storm totals in ranging from 38 to 56 cm. The Squaw Creek storm response was unique for this area, in that it remained turbid for about 2 months following the storms. Subsequent small storms through June, 2013 have also generated prolonged turbidity. This may be attributable to the remobilization of fine particles temporarily stored in the channel network. Preliminary observations from field reconnaissance include the following: a) Erosional processes were dominated by sheet, rill, and gully erosion, and the resulting sediment delivered to channels was rich in fine particles and gravels; b) Landslides were infrequent, and as a result, a limited amount of large rock and logs were delivered to channels; c) Sediment laden flows occurred in most burned low order channels, but classic debris flows, those scouring all vegetation from channel bottoms, were very uncommon; d) Most road stream crossing culverts failed in high severity burn areas; e) Low gradient stream reaches in Squaw Creek were aggraded with fine sediment; f) Sustained high levels of turbidity occurred in the main stem of Squaw Creek. The goals of this study are to characterize relative roles of surface erosion, landslides, and debris flows in delivering sediment to streams after the fire, and if possible, to develop a rough sediment budget, comparing the amount of sediment delivered to the reservoir to that mobilized on hillslopes and in channels. A combination of remote sensing and field methods are being used. Remote sensing methods include post-fire air photo interpretation and mapping, LiDAR data analysis, and reservoir bathymetry. Field methods include reconnaissance traverses, and transects for direct estimates of sediment volume from surface erosion, gullies, and landslides. Results of this study will improve our understanding of erosional and sedimentation processes in this specific post-wildfire response domain, including reservoir sedimentation rates. They will also provide land managers with sound information upon which to base future decisions on the management of the local natural resources. Lastly, they will facilitate the work of Burned Area Emergency Response teams (BAER) which respond to future wildfires in this domain, and promote development of better designs for road/stream crossings.

The importance of momentum transfer in collision-induced breakups in low Earth orbit

NASA Technical Reports Server (NTRS)

Reynolds, Robert C.; Lillie, Brian J.

1991-01-01

Although there is adequate information on larger objects in low Earth orbit, specifically those objects larger than about 10 cm in diameter, there is little direct information on objects from this size down to 1 mm. Yet, this is the sized regime where objects acting as projectiles represent the ability to seriously damage or destroy a functioning spacecraft if they collide with it. The observed consequences of known collisional breakups in orbit indicates no significant momentum transfer in the resulting debris cloud. The position taken in this paper is that this is an observational selection effect: what is seen in these events is an explosion-like breakup of the target structure arising from shock waves introduced into the structure by the collision, but one that occurs significantly after the collision processes are completed; the collision cloud, in which there is momentum transfer, consists of small, unobserved fragments. Preliminary computations of the contribution of one known collisional breakup, Solwind at 500 km in 1985, and Cosmos 1275 in 1981, assume no momentum transfer on breakup and indicate that these two events are the dominant contributors to the current millimeter and centimeter population. A different story would emerge if momentum transfer was taken into account. The topics covered include: (1) observation of on-orbit collisional breakups; (2) a model for momentum transfer; and (3) velocity space representation of breakup clouds.

Comet Siding Spring Mars Flyby

NASA Image and Video Library

2017-12-08

On October 19, Comet Siding Spring will pass within 88,000 miles of Mars – just one third of the distance from the Earth to the Moon! Traveling at 33 miles per second and weighing as much as a small mountain, the comet hails from the outer fringes of our solar system, originating in a region of icy debris known as the Oort cloud. Comets from the Oort cloud are both ancient and rare. Since this is Comet Siding Spring’s first trip through the inner solar system, scientists are excited to learn more about its composition and the effects of its gas and dust on the Mars upper atmosphere. NASA will be watching closely before, during, and after the flyby with its entire fleet of Mars orbiters and rovers, along with the Hubble Space Telescope and dozens of instruments on Earth. The encounter is certain to teach us more about Oort cloud comets, the Martian atmosphere, and the solar system’s earliest ingredients. Learn more: www.youtube.com/watch?v=FG4KsatjFeI Credit: NASA’s Goddard Space Flight Center NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

Impact of varying lidar measurement and data processing techniques in evaluating cirrus cloud and aerosol direct radiative effects

NASA Astrophysics Data System (ADS)

Lolli, Simone; Madonna, Fabio; Rosoldi, Marco; Campbell, James R.; Welton, Ellsworth J.; Lewis, Jasper R.; Gu, Yu; Pappalardo, Gelsomina

2018-03-01

In the past 2 decades, ground-based lidar networks have drastically increased in scope and relevance, thanks primarily to the advent of lidar observations from space and their need for validation. Lidar observations of aerosol and cloud geometrical, optical and microphysical atmospheric properties are subsequently used to evaluate their direct radiative effects on climate. However, the retrievals are strongly dependent on the lidar instrument measurement technique and subsequent data processing methodologies. In this paper, we evaluate the discrepancies between the use of Raman and elastic lidar measurement techniques and corresponding data processing methods for two aerosol layers in the free troposphere and for two cirrus clouds with different optical depths. Results show that the different lidar techniques are responsible for discrepancies in the model-derived direct radiative effects for biomass burning (0.05 W m-2 at surface and 0.007 W m-2 at top of the atmosphere) and dust aerosol layers (0.7 W m-2 at surface and 0.85 W m-2 at top of the atmosphere). Data processing is further responsible for discrepancies in both thin (0.55 W m-2 at surface and 2.7 W m-2 at top of the atmosphere) and opaque (7.7 W m-2 at surface and 11.8 W m-2 at top of the atmosphere) cirrus clouds. Direct radiative effect discrepancies can be attributed to the larger variability of the lidar ratio for aerosols (20-150 sr) than for clouds (20-35 sr). For this reason, the influence of the applied lidar technique plays a more fundamental role in aerosol monitoring because the lidar ratio must be retrieved with relatively high accuracy. In contrast, for cirrus clouds, with the lidar ratio being much less variable, the data processing is critical because smoothing it modifies the aerosol and cloud vertically resolved extinction profile that is used as input to compute direct radiative effect calculations.

Super-cooled liquid water topped sub-arctic clouds and precipitation - investigation based on combination of ground-based in-situ and remote-sensing observations

NASA Astrophysics Data System (ADS)

Hirsikko, Anne; Brus, David; O'Connor, Ewan J.; Filioglou, Maria; Komppula, Mika; Romakkaniemi, Sami

2017-04-01

In the high and mid latitudes super-cooled liquid water layers are frequently observed on top of clouds. These layers are difficult to forecast with numerical weather prediction models, even though, they have strong influence on atmospheric radiative properties, cloud microphysical properties, and subsequently, precipitation. This work investigates properties of super-cooled liquid water layer topped sub-arctic clouds and precipitation observed with ground-based in-situ (cloud probes) and remote-sensing (a cloud radar, Doppler and multi-wavelength lidars) instrumentation during two-month long Pallas Cloud Experiment (PaCE 2015) in autumn 2015. Analysis is based on standard Cloudnet scheme supplemented with new retrieval products of the specific clouds and their properties. Combination of two scales of observation provides new information on properties of clouds and precipitation in the sub-arctic Pallas region. Current status of results will be presented during the conference. The authors acknowledge financial support by the Academy of Finland (Centre of Excellence Programme, grant no 272041; and ICINA project, grant no 285068), the ACTRIS2 - European Union's Horizon 2020 research and innovation programme under grant agreement No 654109, the KONE foundation, and the EU FP7 project BACCHUS (grant no 603445).

Temporal Evolution of SL-9 Impact Sites on Jupiter and Global Maps of Jupiter from Multi-Observatory Visible and Infrared Images

NASA Technical Reports Server (NTRS)

Limaye, Sanjay S.

1996-01-01

The objective of this research was to investigate the temporal behavior of the impact features on Jupiter created by the fragments of the Shoemaker Levy-9 comet that collided with the planet in July 1994. The primary observations used in the study were ground based images of Jupiter acquired from the Swedish Solar Vacuum Tube on the island of La Palma in the Canary Islands. The measurement of position of the impact features in images acquired immediately after the impact over a period of a few days revealed that the apparent drift rates were too high and that a repetitive pattern could be seen in the longitude position on successive rotations. This could be explained only by the fact that the measured longitudes of the impact sites were being affected by parallax due to a significant elevation of the impact debris above the nominal cloud top altitude value used for image navigation. Once the apparent positions are analyzed as a function of the meridian angle, the parallax equation can be used to infer the height of the impact features above the cloud deck, once the true impact position (longitude) for the feature is known. Due to their inherent high spatial resolution, the HST measurements of the impact site locations have been accepted widely. However, these suffer from the parallax themselves since few of them were obtained at central meridian. Ground based imaging have the potential to improve this knowledge as they do observe most of the impact sites on either side of the central meridian, except for the degraded resolution. Measurements over a large number of images enables us to minimize the position error through regression and thus estimate both the actual impact site location devoid of parallax bias, and also of the altitude level of the impact debris above the cloud deck. With rapid imaging there is the potential to examine the time evolution of the altitude level. Several hundred ground based images were processed, navigated and subjected to the impact site location measurements. HST images were also acquired and used to calibrate the results and to improve the sample. The resources available enabled an in-depth study only of impact site A, however, many more images have since become available through the global network observations through Lowell Observatory.

Volcano Hazards - A National Threat

USGS Publications Warehouse

,

2006-01-01

When the violent energy of a volcano is unleashed, the results are often catastrophic. The risks to life, property, and infrastructure from volcanoes are escalating as more and more people live, work, play, and travel in volcanic regions. Since 1980, 45 eruptions and 15 cases of notable volcanic unrest have occurred at 33 U.S. volcanoes. Lava flows, debris avalanches, and explosive blasts have invaded communities, swept people to their deaths, choked major riverways, destroyed bridges, and devastated huge tracts of forest. Noxious volcanic gas emissions have caused widespread lung problems. Airborne ash clouds have disrupted the health, lives, and businesses of hundreds of thousands of people; caused millions of dollars of aircraft damage; and nearly brought down passenger flights.

An Investigation of Aerosol-Cloud-Precipitation Interactions in the South-East Pacific Using DOE G-1 Data and WRF/Chem Large Eddy Simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

McFarlane, Sally; Feingold, Graham; Kazil, Jan

2015-12-04

Under this grant, we investigated marine boundary layer clouds, their properties, behavior, and response to human activity and climate change, with a focus on scales and processes that cannot be studied with climate models. Investigated topics and results are summarized in this section. Detailed information are given in subsequent sections, followed by a list of resulting publications.

Formation of a deposit on workpiece surface in polishing nonmetallic materials

NASA Astrophysics Data System (ADS)

Filatov, Yu. D.; Monteil, G.; Sidorko, V. I.; Filatov, O. Y.

2013-05-01

During the last decades in the theory of machining nonmetallic materials some serious advances have been achieved in the field of applying fundamental scientific approaches to the grinding and polishing technologies for high-quality precision surfaces of electronic components, optical systems, and decorative articles made of natural and synthetic stone [1-9]. These achievements include a cluster model of material removal in polishing dielectric workpieces [1-3, 6-7] and a physical-statistical model of formation of debris (wear) particles and removal thereof from a workpiece surface [8-10]. The aforesaid models made it possible to calculate, without recourse to Preston's linear law, the removal rate in polishing nonmetallic materials and the wear intensity for bound-abrasive tools. Equally important for the investigation of the workpiece surface generation mechanism and formation of debris particles are the kinetic functions of surface roughness and reflectance of glass and quartz workpiece surfaces, which have been established directly in the course of polishing. During the in situ inspection of a workpiece surface by laser ellipsometry [11] and reflectometry [12] it was found out that the periodic change of the light reflection coefficient of a workpiece surface being polished is attributed to the formation of fragments of a deposit consisting of work material particles (debris particles) and tool wear particles [13, 14]. The subsequent studies of the mechanism of interaction between the debris particles and wear particles in the tool-workpiece contact zone, which were carried out based on classical concepts [15, 16], yielded some unexpected results. It was demonstrated that electrically charged debris and wear particles, which are located in the coolant-filled gap between a tool and a workpiece, move by closed circular trajectories enclosed in spheres measuring less than one fifth of the gap thickness. This implies that the probability of the debris and wear particles reaching the tool and workpiece surfaces and, especially, getting localized on the surfaces is extremely low, which contradicts the results of experimental examination of these surfaces. Based on the quantum-mechanical description of the process of scattering of the debris and wear particles that are as small as 3-4 nm in the tool-workpiece contact zone, the mechanism of formation of a workpiece microrelief and the mechanism of formation of a debris-particle deposit on the tool surface were clarified [17-21]. However, the mechanism of formation of the deposit fragments and their discrete arrangement on the workpiece surface in the process of polishing with a bound-abrasive tool has not been studied yet.

Characterization of cumulus cloud fields using trajectories in the center of gravity versus water mass phase space: 2. Aerosol effects on warm convective clouds: Center of Gravity Versus Water Mass 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heiblum, Reuven H.; Altaratz, Orit; Koren, Ilan

2016-06-07

In Part I of this work a 3D cloud tracking algorithm and phase-space of center of gravity altitude versus cloud liquid water mass (CvM space) were introduced and described in detail. We showed how new physical insight can be gained by following cloud trajectories in the CvM space. Here, this approach is used to investigate aerosol effects on cloud fields of warm cumuli. We show a clear effect of the aerosol loading on the shape and size of CvM clusters. We also find fundamental differences in the CvM space between simulations using bin versus bulk microphysical schemes, with the binmore » scheme precipitation expressing much higher sensitivity to changes in aerosol concentrations. Using the bin microphysical scheme, we find that the increase in cloud center of gravity altitude with increase in aerosol concentrations occurs for a wide range of cloud sizes. This is attributed to reduced sedimentation, increased buoyancy and vertical velocities, and increased environmental instability, all of which are tightly coupled to inhibition of precipitation processes and subsequent feedbacks of clouds on their environment. Many of the physical processes shown here are consistent with processes typically associated with cloud invigoration.« less

Nephrotoxicity of Hydrocarbon Propellants to Male, Fischer-344 Rats

DTIC Science & Technology

1983-08-01

debris in medullary tubules and mild to moderate, multifocal, papillary hyperplasia of pelvic urothelium along the surface of the renal papillus...con- trast, etiologic factors leading to papillary hyperplasia of the pelvic urothelium can only be theorized. Hyperplastic pelvic lin- ing cells are...results in the loss of inhibitory chalones (i.e. N factors related to contact inhibition) and the subsequent "release" of nearby surface urothelium to

Sample Preservation - The Key to a Successful Failure Analysis

DTIC Science & Technology

2008-09-01

Acidic Lemon Juice 3 Acidic Vinegar 4 Acidic Tomatoes 5 Acidic Human Skin 6 Acidic Milk 7 Neutral 8 Alkaline Sea Water 9 Alkaline Baking Soda...subsequently removed with alcohol when fractography is performed, although problems may exist with rough fracture surfaces. For these surfaces, a...cleaning Loosely adhering debris and dust Least Organic-solvent cleaning in ultrasonic bath  Toluene or xylene  Ketones  Alcohol  Oil and

Probing Storm Activity on Jupiter

NASA Technical Reports Server (NTRS)

2007-01-01

Scientists assume Jupiter's clouds are composed primarily of ammonia, but only about 1% of the cloud area displays the characteristic spectral fingerprint of ammonia. This composite of infrared images taken by the New Horizons Linear Etalon Infrared Spectral Imager (LEISA) captures several eruptions of this relatively rare breed of ammonia cloud and follows the evolution of the clouds over two Jovian days. (One day on Jupiter is approximately 10 hours, which is how long it takes Jupiter to make one complete rotation about its axis.)

The New Horizons spacecraft was still closing in on the giant planet when it made these observations: Jupiter was 3.4 million kilometers (2.1 million miles) from the New Horizons spacecraft for the LEISA image taken at 19:35 Universal Time on February 26, 2007, and the distance decreased to 2.5 million kilometers (1.6 million miles) for the last image shown. LEISA's spatial resolution scale varied from approximately 210 kilometers (130 miles) for the first image to 160 kilometers (100 miles) for the last one.

New Horizons scientists originally targeted the region slightly northwest (up and to the left) of the Great Red Spot to search for these special ammonia clouds because that's where they were most easily seen during infrared spectral observations made by the Galileo spacecraft. But unlike the churning, turbulent cloud structures seen near the Great Red Spot during the Galileo era, this region has been quieting down during the past several months and was unusually tranquil when New Horizons passed by. Nevertheless, LEISA managed to find other regions of fresh, upwelling ammonia clouds, and the temporal evolution of one such region is displayed in this figure. In the first image, a fresh ammonia cloud (the blue region) sprouts from between white clouds and a dark elongated region. This blue cloud subsequently stretches along the white-dark border in the next two images.

These fresh ammonia clouds trace the strong upwelling of gases from the largely hidden depths of Jupiter to higher altitudes. Presumably, water is also being dragged up from below, and the subsequent condensation of that water, which is far more abundant than ammonia in Jupiter's atmosphere, into cloud droplets energizes the lower troposphere.

LEISA produces images at infrared wavelengths, which is heat radiation that cannot be sensed by the human eye. These 'false color' images were produced by putting images of Jupiter at wavelengths of 1.99 micrometers, 1.94 micrometers and 2.04 micrometers into the red, green and blue channels, respectively, of the image display. Ammonia has an absorption feature at 1.99 microns, and when the colors are combined in this way the fresh ammonia clouds take on a bluish hue.

Research approach and first results on agglomerate compaction in protoplanetary dust simulation in the Cloud Manipulation System

NASA Astrophysics Data System (ADS)

Vedernikov, Andrei; Blum, Jurgen; Ingo Von Borstel, Olaf; Schraepler, Rainer; Balapanov, Daniyar; Cecere, Anselmo

2016-07-01

Nanometre and micrometre-sized solid particles are ubiquitous in space and on Earth - from galaxies, interstellar space, protoplanetary and debris disks to planetary rings and atmospheres, planetary surfaces, comets, interplanetary space, Earth's atmosphere. Apparently, the most intriguing problem in the picture of the formation of planets is the transition from individual microscopic dust grains to kilometre-sized planetesimals. Revealing the mechanisms of this transition is one of the main tasks of the European Space Agency's project Interaction in Cosmic and Atmospheric Particle Systems (ICAPS). It was found that Brownian motion driven agglomeration could not provide the transition within reasonable time scale. As a result, at this stage top scientific goals shifted towards forced agglomeration and concentration of particles, targeting revealing the onset of compaction, experimental study of the evolution of fractal dimensions, size and mass distribution, occurrence of bouncing. The main tasks comprise 1) development of the rapid agglomeration model 2) development of the experimental facilities creating big fractal-type agglomerates from 10 to 1000 μm from a cloud of micrometre-size grains; 3) experimental realization of the rapid agglomeration in microgravity and ground conditions; and 4) in situ investigation of the morphology, mobility, mechanical and optical properties of the free-floating agglomerates, including investigation of thermophoresis, photophoresis of the agglomerates and of the two-phase flow phenomena. To solve the experimental part of the tasks we developed a Cloud Manipulation System, realized as a breadboard (CMS BB) for long duration microgravity platforms and a simplified laboratory version (CMS LV) mostly oriented on short duration microgravity and ground tests. The new system is based on the use of thermophoresis, most favourable for cloud manipulation without creating additional particle-particle forces in the cloud with a possibility of growing single agglomerate out of the whole cloud. The cloud manipulation system additionally provides temperature stabilization or, on the contrary, high temperature variation in the observation volume; formation of controlled temperature gradients, intensive three-dimensional periodic shear flow or three-dimensional gas density pulsations of the contraction-expansion type; application of electrostatic gradients including electro dynamic balancing; imposing of photophoretic force, etc. Their choice and/or combination depend upon particular experimental task. Experiments on forced agglomeration in short duration microgravity conditions of the Bremen drop tower succeeded in rapid growth of extended agglomerates, formation of complex three-dimensional cloud patterns, allowed observing controlled cloud displacement, cloud trapping, particle separation with respect to their electrical charge. The breadboard (CMS BB) and the laboratory version of the Cloud Manipulation System (CMS LV) are new types of scientific instrument with high scientific potential. ESA PRODEX program, the Belgian Federal Science Policy Office, DLR project 50WM1223, ZARM Drop Tower Operation and Service Company Ltd. are greatly acknowledged.

Aqueous-Phase Photochemical Production of Oxidants in Atmospheric Waters.

NASA Astrophysics Data System (ADS)

Allen, John Morrison

1992-01-01

The photochemical formation and subsequent reactions of oxidants plays an important role in the overall chemistry of the atmosphere. Much of the interest in atmospheric oxidation reactions has been fueled by the environmental consequences of the oxidation of sulfur dioxide (SO _2) forming sulfuric acid (H_2 SO_4). Oxidation reactions also play a crucial role in other atmospheric chemical transformations such as: (1) the destruction of tropospheric ozone, (2) redox cycling of transition metals, and (3) oxidation of organic compounds. Much of the research pertaining to atmospheric oxidant formation and the reactions that these oxidants undergo has centered upon gas-phase photochemical oxidant formation and: (1) subsequent reactions in the gas phase, or (2) partitioning of oxidants into cloud and fog drops and subsequent reactions in the aqueous phase. Only a very limited amount of data is available concerning aqueous -phase photochemical sources of oxidants in cloud and fog drops. The focus of one aspect of the work presented in this dissertation is upon the aqueous-phase sunlight photochemical formation of oxidants in authentic cloud and fog water samples from across the United States and Canada. It will be demonstrated that atmospheric waters typically absorb solar ultraviolet radiation at wavelengths ranging from 290 to 340 nm. This absorption is due to the presence of chemical constituents in the cloud and fog waters that contain chromophoric functional groups that give rise to the formation of: (1) singlet molecular oxygen O_2(^1Delta_ {rm g}), (2) peroxyl radicals (HO _2cdot and RO_2 cdot), (3) peroxides (HOOH, ROOH, and ROOR '), and (4) hydroxyl radical ( cdotOH). This work will demonstrate that aqueous-phase photochemical reactions are a significant and in some cases dominant source of these oxidants in cloud and fog drops. The transition metal catalyzed oxidation of SO _2 to H_2SO _4 by molecular oxygen has been extensively studied. This reaction is thought to be an important pathway by which a strong acid is produced within cloud drops under certain conditions. Experiments performed in distilled, deionized water presented in this dissertation will demonstrate that the oxidation of SO_2 in the presence of Fe(III) is much slower in sunlight than in the dark.

Effects of variation in coagulation and photochemistry parameters on the particle size distributions in the Venus clouds

NASA Astrophysics Data System (ADS)

McGouldrick, Kevin

2017-12-01

This paper explores the effects that variation in the coalescence efficiency of the Venus cloud particles can have on the structure of the Venus cloud. It is motivated by the acknowledgment of uncertainties in the measured parameters—and the assumptions made to account for them—that define our present knowledge of the particle characteristics. Specifically, we explore the consequence of allowing the coalescence efficiency of supercooled sulfuric acid in the upper clouds to tend to zero. This produces a cloud that occasionally exhibits an enhancement of small particles at altitude (similar to the upper hazes observed by Pioneer Venus and subsequently shown to be somewhat transient). This simulated cloud occasionally exhibits a rapid growth of particle size near cloud base, exhibiting characteristics similar to those seen in the controversial Mode 3 particles. These results demonstrate that a subset of the variations observed as near-infrared opacity variations in the lower and middle clouds of Venus can be explained by microphysical, in addition to dynamical, variations. Furthermore, the existence of a population of particles exhibiting less efficient coalescence efficiencies would support the likelihood of conditions suitable for charge exchange, hence lightning, in the Venus clouds. We recommend future laboratory studies on the coalescence properties of sulfuric acid under the range of conditions experienced in the Venus clouds. We also recommend future in situ measurements to better characterize the properties of the cloud particles themselves, especially composition and particle habits (shapes).[Figure not available: see fulltext.

Acoustic Fluidization and the Extraordinary Mobility of Sturzstroms

NASA Astrophysics Data System (ADS)

Collins, G. S.; Melosh, H. J.

2002-12-01

Sturzstroms are a rare category of rock avalanche that travel vast horizontal distances with only a comparatively small vertical drop in height. Their extraordinary mobility appears to be a consequence of sustained fluid-like behavior during motion that persists even for driving stresses well below those normally associated with large rock avalanches. One mechanism with the potential for explaining this temporary increase in the mobility of rock debris is acoustic fluidization; where transient, high-frequency pressure fluctuations, generated during the initial collapse and subsequent flow of a mass of rock debris, may locally relieve overburden stresses in the rock mass and thus reduce the frictional resistance to slip between fragments. Here we will present the acoustic fluidization model for the mechanics of sturzstroms, and discuss the conditions under which this process may sustain fluid-like flow of large rock avalanches at low driving stresses. Our work has focused on developing equations for describing the temporal and spatial evolution of acoustic energy within a mass of dry rock debris. We apply this model to the specific process of large, dry rock avalanches. To solve the complex system of equations we have: (1) sought steady state solutions to investigate the circumstances under which acoustic fluidization might facilitate fluid-like motion of the debris at low driving stresses; and (2) simulated the flow of dry rock debris in the presence of acoustic vibrations using a hydrocode, to test the stability of the steady state solutions, investigate the effect of initial conditions and study the avalanche termination process. Results from our modeling work are consistent with the characteristic observations of sturzstroms on Earth. They predict that, under realistic conditions, the flow of a mass of dry rock debris can retain and regenerate enough acoustic energy to perpetuate its own motion, even at very low slope angles; thereby explaining the peculiar long-runout of large rock avalanches. Observations of fluid-like behavior of sturzstroms are supported by our modeling work. The predicted velocity profile through the acoustically fluidized rock avalanche is parabolic; the sturzstrom flows with an effective viscosity that is almost independent of depth within the rock avalanche.

Properties and rotation of molecular clouds in M 33

NASA Astrophysics Data System (ADS)

Braine, J.; Rosolowsky, E.; Gratier, P.; Corbelli, E.; Schuster, K.-F.

2018-04-01

The sample of 566 molecular clouds identified in the CO(2-1) IRAM survey covering the disk of M 33 is explored in detail. The clouds were found using CPROPS and were subsequently catalogued in terms of their star-forming properties as non-star-forming (A), with embedded star formation (B), or with exposed star formation (C, e.g., presence of Hα emission). We find that the size-linewidth relation among the M 33 clouds is quite weak but, when comparing with clouds in other nearby galaxies, the linewidth scales with average metallicity. The linewidth and particularly the line brightness decrease with galactocentric distance. The large number of clouds makes it possible to calculate well-sampled cloud mass spectra and mass spectra of subsamples. As noted earlier, but considerably better defined here, the mass spectrum steepens (i.e., higher fraction of small clouds) with galactocentric distance. A new finding is that the mass spectrum of A clouds is much steeper than that of the star-forming clouds. Further dividing the sample, this difference is strong at both large and small galactocentric distances and the A vs. C difference is a stronger effect than the inner vs. outer disk difference in mass spectra. Velocity gradients are identified in the clouds using standard techniques. The gradients are weak and are dominated by prograde rotation; the effect is stronger for the high signal-to-noise clouds. A discussion of the uncertainties is presented. The angular momenta are low but compatible with at least some simulations. Finally, the cloud velocity gradients are compared with the gradient of disk rotation. The cloud and galactic gradients are similar; the cloud rotation periods are much longer than cloud lifetimes and comparable to the galactic rotation period. The rotational kinetic energy is 1-2% of the gravitational potential energy and the cloud edge velocity is well below the escape velocity, such that cloud-scale rotation probably has little influence on the evolution of molecular clouds.

Use of Field Observations for Understanding Controls of Polar Low Cloud Microphysical Properties

NASA Astrophysics Data System (ADS)

McFarquhar, G. M.

2016-12-01

Although arctic clouds have a net warming effect on the Arctic surface, their radiative effect is sensitive to cloud microphysical properties, namely the sizes, phases and shapes of cloud particles. Such cloud properties are influenced by the numbers, compositions and sizes of aerosols, meteorological conditions, and surface characteristics. Uncertainty in representing cloud-aerosol interactions in varying environmental conditions and associated feedbacks is a major cause in our lack of understanding of why the Arctic is warming faster than the rest of the Earth. Here, the understanding of cloud-aerosol interactions gained from past arctic field experiments is reviewed. Such studies have characterized the structure of single-layer mixed phase clouds that are ubiquitous in the Arctic and investigated different aerosol indirect effect mechanisms acting in these clouds. But, it is still unknown what controls the amount of supercooled water in arctic clouds (especially in complex frequently occurring multi-layer clouds), how probability distributions of cloud properties and radiative heating and their subsequent impact on temperature profiles and underlying snow and sea ice cover vary with aerosol loading and composition in different surface and meteorological conditions, how the composition and concentration of arctic aerosols and cloud microphysical properties vary annually and interannually, and how cloud-aerosol-radiative interactions can be better represented in models with varying temporal and spatial scales. These needs can be addressed in two ways. First, there is a need for comprehensive and routine aircraft, UAV and tethered balloon measurements in the presence of ground, air or space-based remote sensors over a variety of surface and meteorological conditions. Second, planned observational campaigns (the Measurements of Aerosols Radiation and Clouds over the Southern Oceans MARCUS and the Southern Oceans Cloud Radiation Transport Experimental Study SOCRATES) should provide cloud, aerosol, radiative and precipitation observations over the pristine and continually cloudy Southern Oceans that are remote from natural and continental anthropogenic aerosol sources should provide a process-oriented understanding of cloud-aerosol interactions in liquid and ice clouds.

A new method for isolation of polyethylene wear debris from tissue and synovial fluid.

PubMed

Visentin, Manuela; Stea, Susanna; Squarzoni, Stefano; Antonietti, Barbara; Reggiani, Matteo; Toni, Aldo

2004-11-01

Sub-micron-sized ultrahigh molecular-weight polyethylene (PE) debris is generated in the joint space as a result of articulation and cyclic loading of an orthopaedic implant. Its characterization requires isolation and subsequent analysis by ultra-structural methods. An innovative method based on the digestion of paraffin-embedded tissue samples was proposed. Tissue slices were digested with sodium hypochlorite directly on polycarbonate filter. The same procedure could be applied also to fresh synovial fluid. Plastic particles were not lost or damaged during treatment. Chemical identification of particles was done by micro-Raman spectroscopy that confirmed purity of retrieved PE particles. Size and shape of PE particles were characterised using scanning electron microscopy and were comparable in number and morphology to the retrieval by other authors. Equivalent diameter ranged from 0.48 to 0.95microm and particle number ranged from 9 to 23x10(9)/cm(3).

Work plan for the radiological survey for the David Witherspoon, Incorporated, Landfill-1630 site, Knoxville, Tennessee

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-07-01

This work plan establishes the methods and requirements for performing a radiological survey at the David Witherspoon, Incorporated, Landfill-1630 Site, Knoxville, Tennessee (DWI 1630 Site) in accordance with requirements under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA). The radiological survey will identify the radiological contamination level of the equipment and debris stored at the DWI 1630 Site. The data generated from the survey activities will support the decisions for characterization of the equipment/debris and aid in subsequent disposition and waste handling. The survey activities to be performed under this work plan include an equipment radiological survey,more » a walkover survey, and an immunoassay testing for polychlorinated biphenyls (PCBs). This work plan includes a quality assurance (QA)/quality control (QC) project plan, a health and safety (H&S) plan, and a waste management plan.« less

Ceramic femoral component fracture in total knee arthroplasty: an analysis using fractography, fourier-transform infrared microscopy, contact radiography and histology.

PubMed

Krueger, Alexander P; Singh, Gurpal; Beil, Frank Timo; Feuerstein, Bernd; Ruether, Wolfgang; Lohmann, Christoph H

2014-05-01

Ceramic components in total knee arthroplasty (TKA) are evolving. We analyze the first case of BIOLOX delta ceramic femoral component fracture. A longitudinal midline fracture in the patellar groove was present, with an intact cement mantle and no bony defects. Fractographic analysis with laser scanning microscopy and white light interferometry showed no evidence of arrest lines, hackles, wake hackles, material flaws, fatigue or crack propagation. Analysis of periprosthetic tissues with Fourier-transform infrared (FT-IR) microscopy, contact radiography, histology, and subsequent digestion and high-speed centrifugation did not show ceramic debris. A macrophage-dominated response was present around polyethylene debris. We conclude that ceramic femoral component failure in this case was related to a traumatic event. Further research is needed to determine the suitability of ceramic components in TKA. Copyright © 2014 Elsevier Inc. All rights reserved.

LDEF meteoroid and debris database

NASA Technical Reports Server (NTRS)

Dardano, C. B.; See, Thomas H.; Zolensky, Michael E.

1994-01-01

The Long Duration Exposure Facility (LDEF) Meteoroid and Debris Special Investigation Group (M&D SIG) database is maintained at the Johnson Space Center (JSC), Houston, Texas, and consists of five data tables containing information about individual features, digitized images of selected features, and LDEF hardware (i.e., approximately 950 samples) archived at JSC. About 4000 penetrations (greater than 300 micron in diameter) and craters (greater than 500 micron in diameter) were identified and photodocumented during the disassembly of LDEF at the Kennedy Space Center (KSC), while an additional 4500 or so have subsequently been characterized at JSC. The database also contains some data that have been submitted by various PI's, yet the amount of such data is extremely limited in its extent, and investigators are encouraged to submit any and all M&D-type data to JSC for inclusion within the M&D database. Digitized stereo-image pairs are available for approximately 4500 features through the database.

Assessing the Suitability of the ClOud Reflection Algorithm (CORA) in Modelling the Evolution of an Artificial Plasma Cloud in the Ionosphere

NASA Astrophysics Data System (ADS)

Jackson-Booth, N.

2016-12-01

Artificial Ionospheric Modification (AIM) attempts to modify the ionosphere in order to alter the propagation environment. It can be achieved through injecting the ionosphere with aerosols, chemicals or radio signals. The effects of any such release can be detected through the deployment of sensors, including ground based high frequency (HF) sounders. During the Metal Oxide Space Clouds (MOSC) experiment (undertaken in April/May 2013 in the Kwajalein Atoll, part of the Marshall Islands) several oblique ionograms were recorded from a ground based HF system. These ionograms were collected over multiple geometries and allowed the effects on the HF propagation environment to be understood. These ionograms have subsequently been used in the ClOud Reflection Algorithm (CORA) to attempt to model the evolution of the cloud following release. This paper describes the latest validation results from CORA, both from testing against ionograms, but also other independent models of cloud evolution from MOSC. For all testing the various cloud models (including that generated by CORA) were incorporated into a background ionosphere through which a 3D numerical ray trace was run to produce synthetic ionograms that could be compared with the ionograms recorded during MOSC.

Modeling Studying the Role of Bacteria on ice Nucleation Processes

NASA Astrophysics Data System (ADS)

Sun, J.

2006-12-01

Certain air-borne bacteria have been recognized as active ice nuclei at the temperatures warm than - 10°C. Ice nucleating bacteria commonly found in plants and ocean surface. These ice nucleating bacteria are readily disseminated into the atmosphere and have been observed in clouds and hailstones, and their importance in cloud formation process and precipitation, as well as causing diseases in plants and animal kingdom, have been considered for over two decades, but their significance in atmospheric processes are yet to be understood. A 1.5-D non-hydrostatic cumulus cloud model with bin-resolved microphysics is developed and is to used to examine the relative importance of sulphate aerosol concentrations on the evolution of cumulus cloud droplet spectra and ice multiplication process, as well as ice initiation process by ice nucleating bacteria in the growing stage of cumulus clouds and the key role of this process on the ice multiplication in the subsequent dissipating stage of cumulus clouds. In this paper, we will present some sensitivity test results of the evolution of cumulus cloud spectra, ice concentrations at various concentrations of sulfate aerosols, and at different ideal sounding profiles. We will discuss the implication of our results in understanding of ice nucleation processes.

Small negative cloud-to-ground lightning reports at the NASA Kennedy Space Center and Air Force Eastern Range

NASA Astrophysics Data System (ADS)

Wilson, Jennifer G.; Cummins, Kenneth L.; Krider, E. Philip

2009-12-01

The NASA Kennedy Space Center (KSC) and Air Force Eastern Range (ER) use data from two cloud-to-ground (CG) lightning detection networks, the Cloud-to-Ground Lightning Surveillance System (CGLSS) and the U.S. National Lightning Detection Network™ (NLDN), and a volumetric lightning mapping array, the Lightning Detection and Ranging (LDAR) system, to monitor and characterize lightning that is potentially hazardous to launch or ground operations. Data obtained from these systems during June-August 2006 have been examined to check the classification of small, negative CGLSS reports that have an estimated peak current, ∣Ip∣ less than 7 kA, and to determine the smallest values of Ip that are produced by first strokes, by subsequent strokes that create a new ground contact (NGC), and by subsequent strokes that remain in a preexisting channel (PEC). The results show that within 20 km of the KSC-ER, 21% of the low-amplitude negative CGLSS reports were produced by first strokes, with a minimum Ip of -2.9 kA; 31% were by NGCs, with a minimum Ip of -2.0 kA; and 14% were by PECs, with a minimum Ip of -2.2 kA. The remaining 34% were produced by cloud pulses or lightning events that we were not able to classify.

The CM SAF CLAAS-2 cloud property data record

NASA Astrophysics Data System (ADS)

Benas, Nikos; Finkensieper, Stephan; Stengel, Martin; van Zadelhoff, Gerd-Jan; Hanschmann, Timo; Hollmann, Rainer; Fokke Meirink, Jan

2017-04-01

A new cloud property data record was lately released by the EUMETSAT Satellite Application Facility on Climate Monitoring (CM SAF), based on measurements from geostationary Meteosat Spinning Enhanced Visible and Infrared Imager (SEVIRI) sensors, spanning the period 2004-2015. The CLAAS-2 (Cloud property dAtAset using SEVIRI, Edition 2) data record includes cloud fractional coverage, thermodynamic phase, cloud top height, water path and corresponding optical thickness and particle effective radius separately for liquid and ice clouds. These variables are available at high resolution 15-minute, daily and monthly basis. In this presentation the main improvements in the retrieval algorithms compared to the first edition of the data record (CLAAS-1) are highlighted along with their impact on the quality of the data record. Subsequently, the results of extensive validation and inter-comparison efforts against ground observations, as well as active and passive satellite sensors are summarized. Overall good agreement is found, with similar spatial and temporal characteristics, along with small biases caused mainly by differences in retrieval approaches, spatial/temporal samplings and viewing geometries.

Turbulent Mixing at the Edge of a Cloud

NASA Astrophysics Data System (ADS)

Shaw, Raymond; Beals, Matthew; Fugal, Jacob; Kumar, Bipin; Lu, Jiang; Schumacher, Joerg; Stith, Jeffrey

2013-11-01

Numerical and field experiments have been brought to bear on the question of how atmospheric clouds respond when they experience turbulent mixing with their environment. Simply put, we ask when a cloud is diluted, do all droplets evaporate uniformly (homogeneous mixing) or does a subset of droplets evaporate completely, leaving the remaining droplets unaffected (inhomogeneous mixing)? First, the entrainment of clear air and its subsequent mixing with a filament of cloudy air is studied in DNS that combine the Eulerian description of the turbulent velocity, temperature and vapor fields with a Lagrangian cloud droplet ensemble. The simulations provide guidance on the proper definition of the thermodynamic response time for the Damkoehler number, and demonstrate the transition from inhomogeneous to homogeneous mixing as mixing progresses within the inertial subrange. Second, an airborne digital holographic instrument (Holodec) shows that cloud edges are inhomogeneous at the centimeter scales. In local cloud volumes the droplet size distribution fluctuates strongly in number density but with a nearly unchanging mean droplet diameter, until the fluctuations finally cascade to the centimeter scale, when the droplet diameter begins to respond.

Preliminary Spreadsheet of Eruption Source Parameters for Volcanoes of the World

USGS Publications Warehouse

Mastin, Larry G.; Guffanti, Marianne; Ewert, John W.; Spiegel, Jessica

2009-01-01

Volcanic eruptions that spew tephra into the atmosphere pose a hazard to jet aircraft. For this reason, the International Civil Aviation Organization (ICAO) has designated nine Volcanic Ash and Aviation Centers (VAACs) around the world whose purpose is to track ash clouds from eruptions and notify aircraft so that they may avoid these ash clouds. During eruptions, VAACs and their collaborators run volcanic-ashtransport- and-dispersion (VATD) models that forecast the location and movement of ash clouds. These models require as input parameters the plume height H, the mass-eruption rate , duration D, erupted volume V (in cubic kilometers of bubble-free or 'dense rock equivalent' [DRE] magma), and the mass fraction of erupted tephra with a particle size smaller than 63 um (m63). Some parameters, such as mass-eruption rate and mass fraction of fine debris, are not obtainable by direct observation; others, such as plume height or duration, are obtainable from observations but may be unavailable in the early hours of an eruption when VATD models are being initiated. For this reason, ash-cloud modelers need to have at their disposal source parameters for a particular volcano that are based on its recent eruptive history and represent the most likely anticipated eruption. They also need source parameters that encompass the range of uncertainty in eruption size or characteristics. In spring of 2007, a workshop was held at the U.S. Geological Survey (USGS) Cascades Volcano Observatory to derive a protocol for assigning eruption source parameters to ash-cloud models during eruptions. The protocol derived from this effort was published by Mastin and others (in press), along with a world map displaying the assigned eruption type for each of the world's volcanoes. Their report, however, did not include the assigned eruption types in tabular form. Therefore, this Open-File Report presents that table in the form of an Excel spreadsheet. These assignments are preliminary and will be modified to follow upcoming recommendations by the volcanological and aviation communities.

AND YET IT MOVES: THE DANGERS OF ARTIFICIALLY FIXING THE MILKY WAY CENTER OF MASS IN THE PRESENCE OF A MASSIVE LARGE MAGELLANIC CLOUD

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gómez, Facundo A.; O’Shea, Brian W.; Besla, Gurtina

2015-04-01

Motivated by recent studies suggesting that the Large Magellanic Cloud (LMC) could be significantly more massive than previously thought, we explore whether the approximation of an inertial Galactocentric reference frame is still valid in the presence of such a massive LMC. We find that previous estimates of the LMC’s orbital period and apocentric distance derived assuming a fixed Milky Way (MW) are significantly shortened for models where the MW is allowed to move freely in response to the gravitational pull of the LMC. Holding other parameters fixed, the fraction of models favoring first infall is reduced. Due to this interaction,more » the MW center of mass within the inner 50 kpc can be significantly displaced in phase-space in a very short period of time that ranges from 0.3 to 0.5 Gyr by as much as 30 kpc and 75 km s{sup −1}. Furthermore, we show that the gravitational pull of the LMC and response of the MW are likely to significantly affect the orbit and phase space distribution of tidal debris from the Sagittarius dwarf galaxy (Sgr). Such effects are larger than previous estimates based on the torque of the LMC alone. As a result, Sgr deposits debris in regions of the sky that are not aligned with the present-day Sgr orbital plane. In addition, we find that properly accounting for the movement of the MW around its common center of mass with the LMC significantly modifies the angular distance between apocenters and tilts its orbital pole, alleviating tensions between previous models and observations. While these models are preliminary in nature, they highlight the central importance of accounting for the mutual gravitational interaction between the MW and LMC when modeling the kinematics of objects in the MW and Local Group.« less

Interactions of the space debris environment with mega constellations-Using the example of the OneWeb constellation

NASA Astrophysics Data System (ADS)

Radtke, Jonas; Kebschull, Christopher; Stoll, Enrico

2017-02-01

Recently, several announcements have been published to deploy satellite constellations into Low Earth Orbit (LEO) containing several hundred to thousands of rather small sized objects. The purpose of these constellations is to provide a worldwide internet coverage, even to the remotest areas. Examples of these mega-constellations are one from SpaceX, which is announced to comprise of about 4000 satellites, the Norwegian STEAM network, which is told to contain 4257 satellites, and the OneWeb constellation, which forms one of the smaller constellations with 720 satellites. As example constellation, OneWeb has been chosen. From all announced constellation, OneWeb by far delivered most information, both in regards to constellation design and their plans to encounter space debris issues, which is the reason why it has been chosen for these analyses. In this paper, at first an overview of the planned OneWeb constellation setup is given. From this description, a mission life-cycle is deduced, splitting the complete orbital lifetime of the satellites into four phases. Following, using ESA-MASTER, for each of the mission phases the flux on both single constellations satellites and the complete constellation are performed and the collision probabilities are derived. The focus in this analysis is set on catastrophic collisions. This analysis is then varied parametrically for different operational altitudes of the constellation as well as different lifetimes with different assumptions for the success of post mission disposal (PMD). Following the to-be-expected mean number of collision avoidance manoeuvres during all active mission phases is performed using ARES from ESA's DRAMA tool suite. The same variations as during the flux analysis are considered. Lastly the characteristics of hypothetical OneWeb satellite fragmentation clouds, calculated using the NASA Breakup model, are described and the impact of collision clouds from OneWeb satellites on the constellation itself is analysed.

The vertical structure of convectively-driven cloud microphysics and its dependency on atmospheric conditions: An investigation through observations and modeling

NASA Astrophysics Data System (ADS)

van Diedenhoven, B.; Fridlind, A. M.; Sinclair, K.; Ackerman, A. S.

2016-12-01

It is generally observed that ice crystal sizes decrease as a function of altitude within clouds. This dependency is often explained as resulting from size sorting owing to the greater fall speeds of larger particles, but may also be related to dependence of ice diffusional growth on available water vapor and temperature, or other factors. Furthermore, the vertical variation of ice sizes is expected to be affected by the glaciation temperature of convectively-driven clouds. Realistic modeling of ice formation, growth and sedimentation is crucial to reliably represent vertical structures of ice clouds and cloud evolution in general. In this presentation we use remote sensing observations of glaciation temperature and ice effective radius obtained with airborne instruments to explore how their vertical dependencies vary with atmospheric conditions, such as humidity and wind profiles. Our focus will be on convectively-driven clouds. Subsequently, we test the ability of a quasi-idealized cloud permitting model to reproduce these dependencies of ice formation and size to atmospheric conditions, applying various ice growth and multiplication assumptions. The goal of this study is to identify variables that determine the vertical structure of cold clouds that can be used to evaluate model simulations.

Determination of the chemical properties of residues retained in individual cloud droplets by XRF microprobe at SPring-8

NASA Astrophysics Data System (ADS)

Ma, C.-J.; Tohno, S.; Kasahara, M.; Hayakawa, S.

2004-06-01

To determine the chemical properties of residue retained in individual cloud droplets is primarily important for the understanding of rainout mechanism and aerosol modification in droplet. The sampling of individual cloud droplets were carried out on the summit of Mt. Taiko located in Tango peninsula, Kyoto prefecture, during Asian dust storm event in March of 2002. XRF microprobe system equipped at SPring-8, BL-37XU was applied to the subsequent quantification analysis of ultra trace elements in residues of individual cloud droplets. It was possible to form the replicas of separated individual cloud droplets on the thin collodion film. The two dimensional XRF maps for the residues in individual cloud droplets were clearly drawn by scanning of micro-beam. Also, XRF spectra of trace elements in residues were well resolved. From the XRF spectra for individual residues, the chemical mixed state of residues could be assumed. The chemical forms of Fe (Fe +++) and Zn (Zn +) could be clearly characterized by their K-edge micro-XANES spectra. By comparison of Z/Si mass ratios of residues in cloud droplets and those of the original sands collected in desert areas in China, the aging of ambient dust particles and their in cloud modification were indirectly assumed.

THE GALACTIC CENTER CLOUD G2 AND ITS GAS STREAMER

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pfuhl, Oliver; Gillessen, Stefan; Eisenhauer, Frank

2015-01-10

We present new, deep near-infrared SINFONI @ VLT integral field spectroscopy of the gas cloud G2 in the Galactic Center, from late 2013 August, 2014 April, and 2014 July. G2 is visible in recombination line emission. The spatially resolved kinematic data track the ongoing tidal disruption. The cloud reached minimum distance to the MBH of 1950 Schwarzschild radii. As expected for an observation near the pericenter passage, roughly half of the gas in 2014 is found at the redshifted, pre-pericenter side of the orbit, while the other half is at the post-pericenter, blueshifted side. We also present an orbital solutionmore » for the gas cloud G1, which was discovered a decade ago in L'-band images when it was spatially almost coincident with Sgr A*. The orientation of the G1 orbit in the three angles is almost identical to that of G2, but it has a lower eccentricity and smaller semi-major axis. We show that the observed astrometric positions and radial velocities of G1 are compatible with the G2 orbit, assuming that (1) G1 was originally on the G2 orbit preceding G2 by 13 yr, and (2) a simple drag force acted on it during pericenter passage. Taken together with the previously described tail of G2, which we detect in recombination line emission and thermal broadband emission, we propose that G2 may be a bright knot in a much more extensive gas streamer. This matches purely gaseous models for G2, such as a stellar wind clump or the tidal debris from a partial disruption of a star.« less

Patterned CoCrMo and Al2 O3 surfaces for reduced free wear debris in artificial joint arthroplasty.

PubMed

Tarabolsi, Mohamad; Klassen, Thomas; Mantwill, Frank; Gärtner, Frank; Siegel, Frank; Schulz, Arndt-Peter

2013-12-01

Surface wear of corresponding tribological pairings is still a major problem in the application of artificial joint surgery. This study aims at developing wear reduced surfaces to utilize them in total joint arthroplasty. Using a pico-second laser, samples of medical CoCrMo metal alloy and Al2 O3 ceramic were patterned by laser material removal. The subsequent tribological investigations employed a ring-on-disc method. The results showed that those samples with modified surfaces show less mass or volume loss than those with a regular, smooth surface. Using calf serum as lubricating medium, the volume loss of the structured CoCrMo samples was eight times lower than that of regular samples. By structuring Al2 O3 surfaces, the wear volume could be reduced by 4.5 times. The results demonstrate that defined surface channels or pits enable the local sedimentation of wear debris. Thus, the amount of free debris could be reduced. Fewer abrasives in the lubricated so-called three-body-wear between the contact surfaces should result in less surface damage. Apart from direct influences on the wear behavior, less amounts of free debris of artificial joints should also be beneficial for avoiding undesired reactions with the surrounding soft tissues. The results from this study are very promising. Future investigations should involve the use of simulators meeting the natural conditions in the joint and in vivo studies with living organisms. Copyright © 2013 Wiley Periodicals, Inc., a Wiley Company.

Functional analysis of a specialized prey processing behavior: winnowing by surfperches (Teleostei: Embiotocidae).

PubMed

Drucker, E G; Jensen, J S

1991-12-01

Several surfperches (Embiotocidae), including the black surfperch, Embiotoca jacksoni, exhibit a specialized prey handling behavior known as winnowing, in which ingested food and non-nutritive debris are separated within the oropharyngeal cavity. Prey items are swallowed, and unpalatable material is ejected from the mouth. Winnowing is believed to play an important role in the partitioning of food resources among sympatric embiotocids. We present a mechanistic model for this separative prey processing based on high-speed video analysis, cineradiography, electromyography, and buccal and opercular cavity pressure transducer recording. Winnowing by embiotocids is characterized by premaxillary protrusions repeated cyclically with reduced oral gape. Protrusion is accompanied by depression of the hyoid apparatus and adduction of the opercula. Alternating expansion and contraction of the buccal and opercular cavities generate regular pressure waveforms that indicate bidirectional water flow during processing. Separation of food from debris by Embiotoca jacksoni occurs in three phases. The prey-debris bolus is transported anteriorly and posteriorly within the oropharyngeal cavity and is then sheared by the pharyngeal jaws. Mechanical processing is complemented by the rinsing action of water currents during hydraulic prey transport. The feeding apparatus of Embiotoca jacksoni is functionally versatile, although not obviously specialized relative to that of nonwinnowing surfperches. Protrusion of the premaxillae and depression of the hyoid apparatus are critical to both prey capture and subsequent prey processing. The pharyngeal jaws exhibit kinematic patterns during separation of food from debris distinct from those observed during mastication of uncontaminated prey. This behavioral flexibility facilitates resource partitioning and the coexistence of E. jacksoni in sympatric embiotocid assemblages.

Coincident Aerosol and H2O Retrievals versus HSI Imager Field Campaign ReportH2O Retrievals versus HSI Imager Field Campaign Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, Gail P.; Cipar, John; Armstrong, Peter S.

Two spectrally calibrated tarpaulins (tarps) were co-located at a fixed Global Positioning System (GPS) position on the gravel antenna field at the U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) Climate Research Facility’s Southern Great Plains (SGP) site. Their placement was timed to coincide with the overflight of a new hyperspectral imaging satellite. The intention was to provide an analysis of the data obtained, including the measured and retrieved spectral albedos for the calibration tarps. Subsequently, a full suite of retrieved values of H2O column, and the aerosol overburden, were to be compared to those determined by alternate SGPmore » ground truth assets. To the extent possible, the down-looking cloud images would be assessed against the all-sky images. Because cloud contamination above a certain level precludes the inversion processing of the satellite data, coupled with infrequent targeting opportunities, clear-sky conditions were imposed. The SGP site was chosen not only as a target of opportunity for satellite validation, but as perhaps the best coincident field measurement site, as established by DOE’s ARM Facility. The satellite team had every expectation of using the information obtained from the SGP to improve the inversion products for all subsequent satellite images, including the cloud and radiative models and parameterizations and, thereby, the performance assessment for subsequent and historic image collections. Coordinating with the SGP onsite team, four visits, all in 2009, to the Central Facility occurred: • June 6-8 (successful exploratory visit to plan tarp placements, etc.) • July 18-24 (canceled because of forecast for heavy clouds) • Sep 9-12 (ground tarps placed, onset of clouds) • Nov 7-9 (visit ultimately canceled because of weather predictions). As noted, in each instance, any significant overcast prediction precluded image collection from the satellite. Given the long task-scheduling procedures (which were in place for each time period), coupled with other priorities and the satellite lifetime, no alternate SGP images could be obtained.« less

Radiative effects of global MODIS cloud regimes

PubMed Central

Oreopoulos, Lazaros; Cho, Nayeong; Lee, Dongmin; Kato, Seiji

2018-01-01

We update previously published MODIS global cloud regimes (CRs) using the latest MODIS cloud retrievals in the Collection 6 dataset. We implement a slightly different derivation method, investigate the composition of the regimes, and then proceed to examine several aspects of CR radiative appearance with the aid of various radiative flux datasets. Our results clearly show the CRs are radiatively distinct in terms of shortwave, longwave and their combined (total) cloud radiative effect. We show that we can clearly distinguish regimes based on whether they radiatively cool or warm the atmosphere, and thanks to radiative heating profiles to discern the vertical distribution of cooling and warming. Terra and Aqua comparisons provide information about the degree to which morning and afternoon occurrences of regimes affect the symmetry of CR radiative contribution. We examine how the radiative discrepancies among multiple irradiance datasets suffering from imperfect spatiotemporal matching depend on CR, and whether they are therefore related to the complexity of cloud structure, its interpretation by different observational systems, and its subsequent representation in radiative transfer calculations. PMID:29619289

A Comprehensive Review on Adaptability of Network Forensics Frameworks for Mobile Cloud Computing

PubMed Central

Abdul Wahab, Ainuddin Wahid; Han, Qi; Bin Abdul Rahman, Zulkanain

2014-01-01

Network forensics enables investigation and identification of network attacks through the retrieved digital content. The proliferation of smartphones and the cost-effective universal data access through cloud has made Mobile Cloud Computing (MCC) a congenital target for network attacks. However, confines in carrying out forensics in MCC is interrelated with the autonomous cloud hosting companies and their policies for restricted access to the digital content in the back-end cloud platforms. It implies that existing Network Forensic Frameworks (NFFs) have limited impact in the MCC paradigm. To this end, we qualitatively analyze the adaptability of existing NFFs when applied to the MCC. Explicitly, the fundamental mechanisms of NFFs are highlighted and then analyzed using the most relevant parameters. A classification is proposed to help understand the anatomy of existing NFFs. Subsequently, a comparison is given that explores the functional similarities and deviations among NFFs. The paper concludes by discussing research challenges for progressive network forensics in MCC. PMID:25097880

Radiative effects of global MODIS cloud regimes.

PubMed

Oreopoulos, Lazaros; Cho, Nayeong; Lee, Dongmin; Kato, Seiji

2016-03-16

We update previously published MODIS global cloud regimes (CRs) using the latest MODIS cloud retrievals in the Collection 6 dataset. We implement a slightly different derivation method, investigate the composition of the regimes, and then proceed to examine several aspects of CR radiative appearance with the aid of various radiative flux datasets. Our results clearly show the CRs are radiatively distinct in terms of shortwave, longwave and their combined (total) cloud radiative effect. We show that we can clearly distinguish regimes based on whether they radiatively cool or warm the atmosphere, and thanks to radiative heating profiles to discern the vertical distribution of cooling and warming. Terra and Aqua comparisons provide information about the degree to which morning and afternoon occurrences of regimes affect the symmetry of CR radiative contribution. We examine how the radiative discrepancies among multiple irradiance datasets suffering from imperfect spatiotemporal matching depend on CR, and whether they are therefore related to the complexity of cloud structure, its interpretation by different observational systems, and its subsequent representation in radiative transfer calculations.

Radiative Effects of Global MODIS Cloud Regimes

NASA Technical Reports Server (NTRS)

Oraiopoulos, Lazaros; Cho, Nayeong; Lee, Dong Min; Kato, Seiji

2016-01-01

We update previously published MODIS global cloud regimes (CRs) using the latest MODIS cloud retrievals in the Collection 6 dataset. We implement a slightly different derivation method, investigate the composition of the regimes, and then proceed to examine several aspects of CR radiative appearance with the aid of various radiative flux datasets. Our results clearly show the CRs are radiatively distinct in terms of shortwave, longwave and their combined (total) cloud radiative effect. We show that we can clearly distinguish regimes based on whether they radiatively cool or warm the atmosphere, and thanks to radiative heating profiles to discern the vertical distribution of cooling and warming. Terra and Aqua comparisons provide information about the degree to which morning and afternoon occurrences of regimes affect the symmetry of CR radiative contribution. We examine how the radiative discrepancies among multiple irradiance datasets suffering from imperfect spatiotemporal matching depend on CR, and whether they are therefore related to the complexity of cloud structure, its interpretation by different observational systems, and its subsequent representation in radiative transfer calculations.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Warner-Schmid, D.; Hoshi, Suwaru; Armstrong, D.W.

Aqueous solutions of nonionic surfactants are known to undergo phase separations at elevated temperatures. This phenomenon is known as clouding,' and the temperature at which it occurs is refereed to as the cloud point. Permethylhydroxypropyl-[beta]-cyclodextrin (PMHP-[beta]-CD) was synthesized and aqueous solutions containing it were found to undergo similar cloud-point behavior. Factors that affect the phase separation of PMHP-[beta]-CD were investigated. Subsequently, the cloud-point extractions of several aromatic compounds (i.e., acetanilide, aniline, 2,2[prime]-dihydroxybiphenyl, N-methylaniline, 2-naphthol, o-nitroaniline, m-nitroaniline, p-nitroaniline, nitrobenzene, o-nitrophenol, m-nitrophenol, p-nitrophenol, 4-phenazophenol, 3-phenylphenol, and 2-phenylbenzimidazole) from dilute aqueous solution were evaluated. Although the extraction efficiency of the compounds varied, mostmore » can be quantitatively extracted if sufficient PMHP-[beta]-CD is used. For those few compounds that are not extracted (e.g., o-nitroacetanilide), the cloud-point procedure may be an effective one-step isolation or purification method. 18 refs., 2 figs., 3 tabs.« less

A comprehensive review on adaptability of network forensics frameworks for mobile cloud computing.

PubMed

Khan, Suleman; Shiraz, Muhammad; Wahab, Ainuddin Wahid Abdul; Gani, Abdullah; Han, Qi; Rahman, Zulkanain Bin Abdul

2014-01-01

Network forensics enables investigation and identification of network attacks through the retrieved digital content. The proliferation of smartphones and the cost-effective universal data access through cloud has made Mobile Cloud Computing (MCC) a congenital target for network attacks. However, confines in carrying out forensics in MCC is interrelated with the autonomous cloud hosting companies and their policies for restricted access to the digital content in the back-end cloud platforms. It implies that existing Network Forensic Frameworks (NFFs) have limited impact in the MCC paradigm. To this end, we qualitatively analyze the adaptability of existing NFFs when applied to the MCC. Explicitly, the fundamental mechanisms of NFFs are highlighted and then analyzed using the most relevant parameters. A classification is proposed to help understand the anatomy of existing NFFs. Subsequently, a comparison is given that explores the functional similarities and deviations among NFFs. The paper concludes by discussing research challenges for progressive network forensics in MCC.

Unusual gravitational failures on lava domes of Tatun Volcanic Group, Northern Taiwan.

NASA Astrophysics Data System (ADS)

Belousov, Alexander; Belousova, Marina; Chen, Chang-Hwa; Zellmer, Georg

2010-05-01

Tatun Volcanic Group of Northern Taiwan was formed mainly during the Pleistocene - Early Holocene. Most of the volcanoes are represented by andesitic lava domes of moderate sizes: heights up to 400 m (absolute altitudes 800-1100 m a.s.l.), base diameters up to 2 km, and volumes up to 0.3 km³. Many of the domes have broadly opened (0.5-1.0 km across and up to 140° wide), shallow-incised horseshoe-shaped scars formed by gravitational collapses. The failure planes did not intersect the volcanic conduits, and the scars were not filled by younger volcanic edifices: most of the collapses occurred a long time after the eruptions had ceased. The largest collapse, with a volume 0.1 km³, occurred at eastern part of Datun lava dome. Specific feature of the collapse was that the rear slide blocks did not travel far from the source; they stopped high inside the collapse scar, forming multiple narrow toreva blocks descending downslope. The leading slide blocks formed a low mobile debris avalanche (L~5 km; H~1 km; H/L~0.2). The deposit is composed mainly of block facies. The age of the collapse is older than 24,000 yrs, because the related debris avalanche deposit is covered by a younger debris avalanche deposit of Siaoguanyin volcano having calibrated 14C age 22,600-23,780 BP. The Siaoguanyin debris avalanche was formed as a result of collapse of southern part of a small flank dome. Specific feature of the resulted avalanche - it was hot during deposition. The deposit contains carbonized wood; andesite boulders within the deposit frequently have radial cooling joints, and in rare cases "bread-crust" surfaces. The paucity of fine fractions in the deposit can be connected with elutriation of fines into the convective cloud when the hot avalanche travelled downslope. However in several locations the deposit is represented by typical avalanche blocks surrounded by heterolithologic mixed facies containing abundant clasts of Miocene sandstone (picked up from the substrate). Thus the deposit bears features of both debris avalanches and lithic-rich block-and-ash flows. The avalanche was rather mobile (L~6 km; H~1 km; H/L~0.16), despite its small volume (0.02 km³). Its speed reached 40 m/s at a distance of 5 km from the source (based on 80 m high runup of the avalanche). The characteristics of the avalanche deposit indicate that crystallized, degassed, but still hot material of a newly extruded lava dome was involved in the collapse. Unusual low mobile debris avalanche was formed as a result of collapse of western slope of Mt. Cising. A former lava coulee, which was involved in the collapse, underwent only weak disintegration: debris avalanche deposit is represented by big boulders with few fine grained matrix. Leading snout of the landslide traveled only 2 km, while rear slide blocks stopped near the landslide source forming multiple narrow toreva blocks descending downslope. Volume of the collapse 0.05 km³; maximum dropped height 0.5 km, H/L 0.25. Around the distal snout of the avalanche a "bulldozer facies" is well developed. Dating of vegetation entrained into the deposit gave 14C calibrated age 6000-6080 BP. Mobility of the studied debris avalanches was twice smaller than the average mobility of volcanic debris avalanches. Relatively small volume of the collapses, the particular type of material involved (massive lava domes) and the fact that the collapses occurred long after the volcanoes stopped erupting may have played a role in the low mobility of the debris avalanches of the Tatun Group.

Accumulation and fragmentation of plastic debris in global environments

PubMed Central

Barnes, David K. A.; Galgani, Francois; Thompson, Richard C.; Barlaz, Morton

2009-01-01

One of the most ubiquitous and long-lasting recent changes to the surface of our planet is the accumulation and fragmentation of plastics. Within just a few decades since mass production of plastic products commenced in the 1950s, plastic debris has accumulated in terrestrial environments, in the open ocean, on shorelines of even the most remote islands and in the deep sea. Annual clean-up operations, costing millions of pounds sterling, are now organized in many countries and on every continent. Here we document global plastics production and the accumulation of plastic waste. While plastics typically constitute approximately 10 per cent of discarded waste, they represent a much greater proportion of the debris accumulating on shorelines. Mega- and macro-plastics have accumulated in the highest densities in the Northern Hemisphere, adjacent to urban centres, in enclosed seas and at water convergences (fronts). We report lower densities on remote island shores, on the continental shelf seabed and the lowest densities (but still a documented presence) in the deep sea and Southern Ocean. The longevity of plastic is estimated to be hundreds to thousands of years, but is likely to be far longer in deep sea and non-surface polar environments. Plastic debris poses considerable threat by choking and starving wildlife, distributing non-native and potentially harmful organisms, absorbing toxic chemicals and degrading to micro-plastics that may subsequently be ingested. Well-established annual surveys on coasts and at sea have shown that trends in mega- and macro-plastic accumulation rates are no longer uniformly increasing: rather stable, increasing and decreasing trends have all been reported. The average size of plastic particles in the environment seems to be decreasing, and the abundance and global distribution of micro-plastic fragments have increased over the last few decades. However, the environmental consequences of such microscopic debris are still poorly understood. PMID:19528051

Forewarning of Debris flows using Intelligent Geophones

NASA Astrophysics Data System (ADS)

PK, I.; Ramesh, M. V.

2017-12-01

Landslides are one of the major catastrophic disasters that cause significant damage to human life and civil structures. Heavy rainfall on landslide prone areas can lead to most dangerous debris flow, where the materials such as mud, sand, soil, rock, water and air will move with greater velocity down the mountain. This sudden slope instability can lead to loss of human life and infrastructure. According to our knowledge, till now no one could identify the minutest factors that lead to initiation of the landslide. In this work, we aim to study the landslide phenomena deeply, using the landslide laboratory set up in our university. This unique mechanical simulator for landslide initiation is equipped with the capability to generate rainfall, seepage, etc., in the laboratory setup. Using this setup, we aim to study several landslide initiation scenarios generated by varying different parameters. The complete setup will be equipped with heterogeneous sensors such as rain gauge, moisture sensor, pore pressure sensor, strain gauges, tiltmeter, inclinometer, extensometer, and geophones. Our work will focus on the signals received from the intelligent geophone system for identifying the underground vibrations during a debris flow. Using the large amount of signals derived from the laboratory set up, we have performed detailed signal processing and data analysis to determine the fore warning signals captured by these heterogeneous sensors. Detailed study of these heterogeneous signals has provided the insights to forewarning the community based on the signals generated during the laboratory tests. In this work we will describe the details of the design, development, methodology, results, inferences and the suggestion for the next step to detect and forewarn the students. The response of intelligent geophone sensors at the time of failure, failure style and subsequent debris flow for heterogeneous soil layers were studied, thus helping in the development of fore warning systems for debris flows.

Contrasting medial moraine development at adjacent temperate, maritime glaciers: Fox and Franz Josef Glaciers, South Westland, New Zealand

NASA Astrophysics Data System (ADS)

Brook, Martin; Hagg, Wilfried; Winkler, Stefan

2017-08-01

Medial moraines form important pathways for sediment transportation in valley glaciers. Despite the existence of well-defined medial moraines on several glaciers in the New Zealand Southern Alps, medial moraines there have hitherto escaped attention. The evolving morphology and debris content of medial moraines on Franz Josef Glacier and Fox Glacier on the western flank of the Southern Alps is the focus of this study. These temperate maritime glaciers exhibit accumulation zones of multiple basins that feed narrow tongues flowing down steep valleys and terminate 400 m above sea level. The medial moraines at both glaciers become very prominent in the lower ablation zones, where the medial moraines widen, and develop steeper flanks coeval with an increase in relative relief. Medial moraine growth appears somewhat self-limiting in that relief and slope angle increase eventually lead to transport of debris away from the medial moraine by mass-movement-related processes. Despite similarities in overall morphologies, a key contrast in medial moraine formation exists between the two glaciers. At Fox Glacier, the medial moraine consists of angular rockfall-derived debris, folded to varying degrees along flow-parallel axes throughout the tongue. The debris originates above the ELA, coalesces at flow-unit boundaries, and takes a medium/high level transport pathway before subsequently emerging at point-sources aligned with gently dipping fold hinges near the snout. In contrast at Franz Josef Glacier, the medial moraine emerges farther down-glacier immediately below a prominent rock knob. Clasts show a mix of angular to rounded shapes representing high level transport and subglacially transported materials, the latter facies possibly also elevated by supraglacial routing of subglacial meltwater. Our observations confirm that a variety of different debris sources, transport pathways, and structural glaciological processes can interact to form medial moraines within New Zealand's Southern Alps.

Accumulation and fragmentation of plastic debris in global environments.

PubMed

Barnes, David K A; Galgani, Francois; Thompson, Richard C; Barlaz, Morton

2009-07-27

One of the most ubiquitous and long-lasting recent changes to the surface of our planet is the accumulation and fragmentation of plastics. Within just a few decades since mass production of plastic products commenced in the 1950s, plastic debris has accumulated in terrestrial environments, in the open ocean, on shorelines of even the most remote islands and in the deep sea. Annual clean-up operations, costing millions of pounds sterling, are now organized in many countries and on every continent. Here we document global plastics production and the accumulation of plastic waste. While plastics typically constitute approximately 10 per cent of discarded waste, they represent a much greater proportion of the debris accumulating on shorelines. Mega- and macro-plastics have accumulated in the highest densities in the Northern Hemisphere, adjacent to urban centres, in enclosed seas and at water convergences (fronts). We report lower densities on remote island shores, on the continental shelf seabed and the lowest densities (but still a documented presence) in the deep sea and Southern Ocean. The longevity of plastic is estimated to be hundreds to thousands of years, but is likely to be far longer in deep sea and non-surface polar environments. Plastic debris poses considerable threat by choking and starving wildlife, distributing non-native and potentially harmful organisms, absorbing toxic chemicals and degrading to micro-plastics that may subsequently be ingested. Well-established annual surveys on coasts and at sea have shown that trends in mega- and macro-plastic accumulation rates are no longer uniformly increasing: rather stable, increasing and decreasing trends have all been reported. The average size of plastic particles in the environment seems to be decreasing, and the abundance and global distribution of micro-plastic fragments have increased over the last few decades. However, the environmental consequences of such microscopic debris are still poorly understood.

Monitoring and modelling of landslide and debris flow impact on transport and building infrasructure in the Carpathians

NASA Astrophysics Data System (ADS)

Ivanik, Olena; Shevchuk, Viktor; Yahno, Evgen

2016-04-01

Mechanisms and factors of formation of landslide and debris flow processes are examined in terms of model objects in the Carpathians. The study area is within Eastern Carpathians and Transcarpathian depression (Tisa river basin). There were investigated more than 220 stabilized and active landslides. The analysis of water-gravitational processes in this region with complex heterogeneous geological structure confirmed the priority nature of occurrence of structural landslides in rheologically different geological environments, and made it possible to create a new classification of structural landslides and conditions of their formation with the decisive influence of destructive zones. This classification is the basis for constructing geological, physical and mathematical models of landslide slopes, and subsequent modeling of the landslide hazard based on the determination of the stress-strain state of slopes. Under the proposed mathematical model, the examined phenomenon is described as thermoelastic-plastic equilibrium of the isotropic matrix under effect of applied mass (gravitational field of the Earth) and surface efforts, inhomogeneous stationary temperature field. In addition, it is assumed that the Young modulus at each point of the matrix depends on the water saturation. Debris and mudflows in the Carpathians have a stage character, non-stationary and avalanche movements. The territory is prone to be affected by debris and mudflows, due to the geological, geomorphological and climatic conditions. Therefore the main conditions of the mudflow formation are as follows: the presence of the rock destruction products which could be a solid phase of debris mudflow; presence of the enough quantity of the rainfall runoff for the unconsolidated material removal; ruggedness of relief that provides simultaneous movement of the big values of the water-soil mass with the big velocities. The algorithm calculating the mudflow impact on infrastructure objects in Carpathians has been developed. It based on the empiric data and fundamental hydrodynamic lows, on formula Bernoulli in particular. Using this formula we obtain the expression for the impingement hydrodynamic pressure:

A study of the large-scale infrared emission from a selected dark cloud

NASA Technical Reports Server (NTRS)

Young, Erick T.

1993-01-01

An investigation of the infrared emission energetics and embedded population in the rho Ophiuchi dark cloud is summarized. With a distance of approximately 140 pc, the rho Ophiuchi cloud is one of the closest regions of recent star formation. It is also one of the best studied such regions with numerous observations at all wavelengths. The Infrared Astronomy Satellite (IRAS) data of the cloud provided a new glimpse of the overall structure of the cloud. In particular, the interaction of radiation from the Sco-Oph OB Association on the external heating of the cloud was very evident on Skyflux and Survey CO-Add images produced by IRAS. The infrared survey also revealed a number of new embedded sources in the cloud which have subsequently been observed from the ground. In earlier study, the overall energies of the cloud using the IRAS data was explored. The main conclusions of that work were: (1) the overall luminosity of the cloud is well explained by the emission of the known B-stars, HD 147889, SR-3, and S1, along with a 15 percent contribution from the external radiation field; (2) the dust physical temperatures were significantly lower than the observed CO gas temperatures; and (3) dust grains are heated to only 10 percent to 20 percent of the total depth into the cloud. This analysis was extended by drawing on data from large-scale CO maps of Loren (1989) and from near-infrared surveys of the embedded population.

Conditions for super-adiabatic droplet growth after entrainment mixing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Fan; Shaw, Raymond; Xue, Huiwen

Cloud droplet response to entrainment and mixing between a cloud and its environment is considered, accounting for subsequent droplet growth during adiabatic ascent following a mixing event. The vertical profile for liquid water mixing ratio after a mixing event is derived analytically, allowing the reduction to be predicted from the mixing fraction and from the temperature and humidity for both the cloud and environment. It is derived for the limit of homogeneous mixing. The expression leads to a critical height above the mixing level: at the critical height the cloud droplet radius is the same for both mixed and unmixedmore » parcels, and the critical height is independent of the updraft velocity and mixing fraction. Cloud droplets in a mixed parcel are larger than in an unmixed parcel above the critical height, which we refer to as the “super-adiabatic” growth region. Analytical results are confirmed with a bin microphysics cloud model. Using the model, we explore the effects of updraft velocity, aerosol source in the environmental air, and polydisperse cloud droplets. Results show that the mixed parcel is more likely to reach the super-adiabatic growth region when the environmental air is humid and clean. It is also confirmed that the analytical predictions are matched by the volume-mean cloud droplet radius for polydisperse size distributions. Lastly, these findings have implications for the origin of large cloud droplets that may contribute to onset of collision–coalescence in warm clouds.« less

Conditions for super-adiabatic droplet growth after entrainment mixing

DOE PAGES

Yang, Fan; Shaw, Raymond; Xue, Huiwen

2016-07-29

Cloud droplet response to entrainment and mixing between a cloud and its environment is considered, accounting for subsequent droplet growth during adiabatic ascent following a mixing event. The vertical profile for liquid water mixing ratio after a mixing event is derived analytically, allowing the reduction to be predicted from the mixing fraction and from the temperature and humidity for both the cloud and environment. It is derived for the limit of homogeneous mixing. The expression leads to a critical height above the mixing level: at the critical height the cloud droplet radius is the same for both mixed and unmixedmore » parcels, and the critical height is independent of the updraft velocity and mixing fraction. Cloud droplets in a mixed parcel are larger than in an unmixed parcel above the critical height, which we refer to as the “super-adiabatic” growth region. Analytical results are confirmed with a bin microphysics cloud model. Using the model, we explore the effects of updraft velocity, aerosol source in the environmental air, and polydisperse cloud droplets. Results show that the mixed parcel is more likely to reach the super-adiabatic growth region when the environmental air is humid and clean. It is also confirmed that the analytical predictions are matched by the volume-mean cloud droplet radius for polydisperse size distributions. Lastly, these findings have implications for the origin of large cloud droplets that may contribute to onset of collision–coalescence in warm clouds.« less

Fast-moving features in the debris disk around AU Microscopii.

PubMed

Boccaletti, Anthony; Thalmann, Christian; Lagrange, Anne-Marie; Janson, Markus; Augereau, Jean-Charles; Schneider, Glenn; Milli, Julien; Grady, Carol; Debes, John; Langlois, Maud; Mouillet, David; Henning, Thomas; Dominik, Carsten; Maire, Anne-Lise; Beuzit, Jean-Luc; Carson, Joseph; Dohlen, Kjetil; Engler, Natalia; Feldt, Markus; Fusco, Thierry; Ginski, Christian; Girard, Julien H; Hines, Dean; Kasper, Markus; Mawet, Dimitri; Ménard, François; Meyer, Michael R; Moutou, Claire; Olofsson, Johan; Rodigas, Timothy; Sauvage, Jean-Francois; Schlieder, Joshua; Schmid, Hans Martin; Turatto, Massimo; Udry, Stephane; Vakili, Farrokh; Vigan, Arthur; Wahhaj, Zahed; Wisniewski, John

2015-10-08

In the 1980s, excess infrared emission was discovered around main-sequence stars; subsequent direct-imaging observations revealed orbiting disks of cold dust to be the source. These 'debris disks' were thought to be by-products of planet formation because they often exhibited morphological and brightness asymmetries that may result from gravitational perturbation by planets. This was proved to be true for the β Pictoris system, in which the known planet generates an observable warp in the disk. The nearby, young, unusually active late-type star AU Microscopii hosts a well-studied edge-on debris disk; earlier observations in the visible and near-infrared found asymmetric localized structures in the form of intensity variations along the midplane of the disk beyond a distance of 20 astronomical units. Here we report high-contrast imaging that reveals a series of five large-scale features in the southeast side of the disk, at projected separations of 10-60 astronomical units, persisting over intervals of 1-4 years. All these features appear to move away from the star at projected speeds of 4-10 kilometres per second, suggesting highly eccentric or unbound trajectories if they are associated with physical entities. The origin, localization, morphology and rapid evolution of these features are difficult to reconcile with current theories.

Evaluation of Ti-48Al-2Cr-2Nb Under Fretting Conditions

NASA Technical Reports Server (NTRS)

Miyoshi, Kazuhisa; Lerch, Bradley A.; Draper, Susan L.; Raj, Sai V.

2001-01-01

The fretting behavior of Ti-48Al-2Cr-2Nb (y-TiAl) in contact with the nickel-base superalloy 718 was examined in air at temperatures from 296 to 823 K (23 to 550 C). The interfacial adhesive bonds between Ti-48Al-2Cr-2Nb and superalloy 718 were generally stronger than the cohesive bonds within Ti-48Al-2Cr-2Nb. The failed Ti-48Al-2Cr-2Nb debris subsequently transferred to the superalloy 718. In reference experiments conducted with Ti-6Al-4V against superalloy 718 under identical fretting conditions, the degree of transfer was greater for Ti-6A1-4V than for Ti-48Al-2Cr-2Nb. Wear of Ti-48Al-2Cr-2Nb generally decreased with increasing fretting frequency. The increasing rate of oxidation at elevated temperatures led to a drop in wear at 473 K. However, fretting wear increased as the temperature was increased from 473 to 823 K. At 723 and 823 K, oxide film disruption generated cracks, loose wear debris, and pits on the Ti-48Al-2Cr-2Nb wear surface. Both increasing slip amplitude and increasing load tended to produce more metallic wear debris, causing severe abrasive wear in the contacting metals.

Evaluating Device Design and Cleanability of Orthopedic Device Models Contaminated with a Clinically Relevant Bone Test Soil.

PubMed

Lucas, Anne D; Nagaraja, Srinidhi; Gordon, Edward A; Hitchins, Victoria M

2015-01-01

Reusable medical devices need to be cleaned prior to disinfection or sterilization and subsequent use to prevent infections. The cleanability of medical devices depends in part on the design of the device. This study examined how models of orthopedic medical devices of increasing complexity retain calcium phosphate bone cement, a relevant test soil for these devices. The dye Alizarin Red S and micro-computed tomography (μCT) were used to assess the amount and location of bone cement debris in a series of model orthopedic devices. Testing was performed after soiling and cleaning once, and soiling and cleaning 10 times. The color change of the dye after reacting with the bone cement was useful for indicating the presence of bone cement in these models. High-resolution μCT analysis provided the volume and location of the bone cement. Models that were more complex retained significantly more bone debris than simpler designs. Model devices repeatedly soiled and cleaned 10 times retained significantly more bone debris than those soiled and cleaned once. Significantly more bone cement was retained in the more complex lumen structures. This information may be useful in designing reusable orthopedic devices, and other complex medical devices with lumens.

A data-driven approach for modeling post-fire debris-flow volumes and their uncertainty

USGS Publications Warehouse

Friedel, Michael J.

2011-01-01

This study demonstrates the novel application of genetic programming to evolve nonlinear post-fire debris-flow volume equations from variables associated with a data-driven conceptual model of the western United States. The search space is constrained using a multi-component objective function that simultaneously minimizes root-mean squared and unit errors for the evolution of fittest equations. An optimization technique is then used to estimate the limits of nonlinear prediction uncertainty associated with the debris-flow equations. In contrast to a published multiple linear regression three-variable equation, linking basin area with slopes greater or equal to 30 percent, burn severity characterized as area burned moderate plus high, and total storm rainfall, the data-driven approach discovers many nonlinear and several dimensionally consistent equations that are unbiased and have less prediction uncertainty. Of the nonlinear equations, the best performance (lowest prediction uncertainty) is achieved when using three variables: average basin slope, total burned area, and total storm rainfall. Further reduction in uncertainty is possible for the nonlinear equations when dimensional consistency is not a priority and by subsequently applying a gradient solver to the fittest solutions. The data-driven modeling approach can be applied to nonlinear multivariate problems in all fields of study.

ASTEROID BELTS IN DEBRIS DISK TWINS: VEGA AND FOMALHAUT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Su, Kate Y. L.; Rieke, George H.; Misselt, Karl A.

2013-02-15

Vega and Fomalhaut are similar in terms of mass, ages, and global debris disk properties; therefore, they are often referred to as 'debris disk twins'. We present Spitzer 10-35 {mu}m spectroscopic data centered at both stars and identify warm, unresolved excess emission in the close vicinity of Vega for the first time. The properties of the warm excess in Vega are further characterized with ancillary photometry in the mid-infrared and resolved images in the far-infrared and submillimeter wavelengths. The Vega warm excess shares many similar properties with the one found around Fomalhaut. The emission shortward of {approx}30 {mu}m from bothmore » warm components is well described as a blackbody emission of {approx}170 K. Interestingly, two other systems, {epsilon} Eri and HR 8799, also show such an unresolved warm dust using the same approach. These warm components may be analogous to the solar system's zodiacal dust cloud, but of far greater mass (fractional luminosity of {approx}10{sup -5} to 10{sup -6} compared to 10{sup -8} to 10{sup -7}). The dust temperature and tentative detections in the submillimeter suggest that the warm excess arises from dust associated with a planetesimal ring located near the water-frost line and presumably created by processes occurring at similar locations in other debris systems as well. We also review the properties of the 2 {mu}m hot excess around Vega and Fomalhaut, showing that the dust responsible for the hot excess is not spatially associated with the dust we detected in the warm belt. We suggest it may arise from hot nano grains trapped in the magnetic field of the star. Finally, the separation between the warm and cold belt is rather large with an orbital ratio {approx}>10 in all four systems. In light of the current upper limits on the masses of planetary objects and the large gap, we discuss the possible implications for their underlying planetary architecture and suggest that multiple, low-mass planets likely reside between the two belts in Vega and Fomalhaut.« less

Asteroid Belts in Debris Disk Twins: Vega and Fomalhaut

NASA Technical Reports Server (NTRS)

Su, Kate Y. L.; Rieke, George H.; Malhortra, Renu; Stapelfeldt, Karl R.; Hughes, A. Meredith; Bonsor, Amy; Wilner, David J.; Balog, Zoltan; Watson, Dan M.; Werner, Michael W.;

Physics of debris clouds from hypervelocity impacts

NASA Technical Reports Server (NTRS)

Zee, Ralph

1993-01-01

The protection scheme developed for long duration space platforms relies primarily upon placing thin metal plates or 'bumpers' around flight critical components. The effectiveness of this system is highly dependent upon its ability to break up and redistribute the momentum of any particle which might otherwise strike the outer surface of the spacecraft. Therefore it is of critical importance to design the bumpers such that maximum dispersion of momentum is achieved. This report is devoted to an in-depth study into the design and development of a laboratory instrument which would permit the in-situ monitoring of the momentum distribution as the impact event occurs. A series of four designs were developed, constructed and tested culminating with the working instrument which is currently in use. Each design was individually tested using the Space Environmental Effects Facility (SEEF) at the Marshall Space Flight Center in Huntsville, Alabama. Along with the development of the device, an experimental procedure was developed to assist in the investigation of various bumper materials and designs at the SEEF. Preliminary results were used to compute data which otherwise were not experimentally obtainable. These results were shown to be in relative agreement with previously obtained values derived through other methods. The results of this investigation indicated that momentum distribution could in fact be measured in-situ as the impact event occurred thus giving a more accurate determination of the effects of experimental parameters on the momentum spread. Data produced by the instrument indicated a Gaussian-type momentum distribution. A second apparatus was developed and it was placed before the shield in the line of travel utilized a plate to collect impact debris scattered backwards. This plate had a passage hole in the center to allow the particle to travel through it and impact the proposed shield material. Applying the law of conservation of angular momentum a backward momentum vector was determined from the angular velocity of the plate. The forward scattered and backward scattered momentum values were then analyzed to judge the distribution of debris. Loss of momentum was attributed to the inaccuracies of the means of measurement. Assumptions of symmetrical debris for the forward and backward scattered directions also contributed to this loss.

Thermal, Radiation and Impact Protective Shields (TRIPS) for Robotic and Human Space Exploration Missions

NASA Technical Reports Server (NTRS)

Loomis, M. P.; Arnold, J. L.

2005-01-01

New concepts for protective shields for NASA s Crew Exploration Vehicles (CEVs) and planetary probes offer improved mission safety and affordability. Hazards include radiation from cosmic rays and solar particle events, hypervelocity impacts from orbital debris/ micrometeorites, and the extreme heating environment experienced during entry into planetary atmospheres. The traditional approach for the design of protection systems for these hazards has been to create single-function shields, i.e. ablative and blanket-based heat shields for thermal protection systems (TPS), polymer or other low-molecular-weight materials for radiation shields, and multilayer, Whipple-type shields for protection from hypervelocity impacts. This paper introduces an approach for the development of a single, multifunctional protective shield, employing nanotechnology- based materials, to serve simultaneously as a TPS, an impact shield and as the first line of defense against radiation. The approach is first to choose low molecular weight ablative TPS materials, (existing and planned for development) and add functionalized carbon nanotubes. Together they provide both thermal and radiation (TR) shielding. Next, impact protection (IP) is furnished through a tough skin, consisting of hard, ceramic outer layers (to fracture the impactor) and sublayers of tough, nanostructured fabrics to contain the debris cloud from the impactor before it can penetrate the spacecraft s interior.

Preventing volcanic catastrophe; the U.S. International Volcano Disaster Assistance Program

USGS Publications Warehouse

Ewert, J.W.; Murray, T.L.; Lockhart, A. B.; Miller, C.D.

1993-01-01

Unfortunately, a storm on November 13, 1985, obscured the glacier-clad summit of Nevado del Ruiz. On that night an explosive eruption tore through the summit and spewed approximately 20 million cubic meters of hot ash and rocks across the snow-covered glacier. These materials were transported across the snow pack by avalanches of hot volcanic debris (pyroclastic flows) and fast-moving, hot, turbulent clouds of gas and ash (pyroclastic surges). The hot pyroclastic flows and surges caused rapid melting of the snow and ice and created large volumes of water that swept down canyons leading away from the summit. As these floods of water descended the volcano, they picked up loose debris and soil from the canyon floors and walls, growing both in volume and density, to form hot lahars. In the river valleys farther down the volcano's flanks, the lahars were as much as 40 m thick and traveled at velocities as fast as 50 km/h. Two and a half hours after the start of the eruption one of the lahars reachered Armero, 74 km from the explosion crater. In a few short minutes most of the town was swept away or buried in a torrent of mud and boulders, and three quaters of the townspeople perished.  

Rocky Planetary Debris Around Young WDs

NASA Astrophysics Data System (ADS)

Gaensicke, B.

2014-04-01

The vast majority of all known planet host stars, including the Sun, will eventually evolve into red giants and finally end their lives as white dwarfs: extremely dense Earth-sized stellar embers. Only close-in planets will be devoured during the red-giant phase. In the solar system, Mars, the asteroid belt, and all the giant planets will escape evaporation, and the same is true for many of the known exo-planets. It is hence certain that a significant fraction of the known white dwarfs were once host stars to planets, and it is very likely that many of them still have remnants of planetary systems. The detection of metals in the atmospheres of white dwarfs is the unmistakable signpost of such evolved planetary systems. The strong surface gravity of white dwarfs causes metals to sink out of the atmosphere on time-scales much shorter than their cooling ages, leading unavoidably to pristine H/He atmospheres. Therefore any metals detected in the atmosphere of a white dwarf imply recent or ongoing accretion of planetary debris. In fact, planetary debris is also detected as circumstellar dust and gas around a number of white dwarfs. These debris disks are formed from the tidal disruption of asteroids or Kuiper belt-like objects, stirred up by left-over planets, and are subsequently accreted onto the white dwarf, imprinting their abundance pattern into its atmosphere. Determining the photospheric abundances of debris-polluted white dwarfs is hence entirely analogue to the use of meteorites, "rocks that fell from the sky", for measuring the abundances of planetary material in the solar system. I will briefly review this new field of exo-planet science, and then focus on the results of a large, unbiased COS snapshot survey of relatively young ( 20-100Myr) white dwarfs that we carried out in Cycle 18/19. * At least 30% of all white dwarfs in our sample are accreting planetary debris, and that fraction may be as high as 50%. * In most cases where debris pollution is detected, the low C/Si ratio demonstrates that the planetary material is of rocky nature. * None of the 9 systems where we measure the C/O ratio shows evidence for carbon-dominated chemistry, implying that "carbon planets" are not common. * In the most polluted white dwarfs, we measure the debris abundances of up to 11 elements, enabling a detailed comparison between the chemistry of exo-planetary material with that of solar system meteorites. We find that the exo-planetary debris shares many characteristics of solar-system material, i.e. a wide spread in the relative abundances of Mg, Fe, Si, and O, a constant Al/Ca ratio, and evidence for differentiation in the form of Fe over-abundances All of the above is suggestive that thermal and collisional processing of planetary material in those systems might have been similar to that in the solar system.

Spatial and Temporal Energy Characterization of Precipitating Electrons for the January 10th, 1997 Magnetic Cloud Event

NASA Technical Reports Server (NTRS)

Spann, J. F., Jr.; Germany, G. A.; Brittnacher, M. J.; Parks, G. K.; Elsen, R.

1997-01-01

The January 10-11, 1997 magnetic cloud event provided a rare opportunity to study auroral energy deposition under varying but intense IMF conditions. The Wind spacecraft located about 100 RE upstream monitored the IMF and plasma parameters during the passing of the cloud. The Polar Ultraviolet Imager (UVI) observed the aurora[ precipitation during the first encounter of the cloud with Earth's magnetosphere and during several subsequent substorm events. The UVI has the unique capability of measuring the energy flux and characteristic energy of the precipitating electrons through the use of narrow band filters that distinguish short and long wavelength molecular nitrogen emissions. The spatial and temporal characteristics of the precipitating electron energy will be discussed beginning with the inception of the event at the Earth early January 1 Oth and continuing through the subsidence of auroral activity on January 11th.

Simulating Shock Triggered Star Formation with AstroBEAR2.0

NASA Astrophysics Data System (ADS)

Li, Shule; Frank, Adam; Blackman, Eric

2013-07-01

Star formation can be triggered by the compression from shocks running over stable clouds. Triggered star formation is a favored explanation for the traces of SLRI's in our solar system. Previous research has shown that when parameters such as shock speed are within a certain range, the gravitational collapse of otherwise stable, dense cloud cores is possible. However, these studies usually focus on the precursors of star formation, and the conditions for the triggering. We use AstroBEAR2.0 code to simulate the collapse and subsequent evolution of a stable Bonnor-Ebert cloud by an incoming shock. Through our simulations, we show that interesting physics happens when the newly formed star interacts with the cloud residue and the post-shock flow. We identify these interactions as controlled by the initial conditions of the triggering and study the flow pattern as well as the evolution of important physics quantities such as accretion rate and angular momentum.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fan, Jiwen; Rosenfeld, Daniel; Zhang, Yuwei

Aerosol-cloud interaction remains the largest uncertainty in climate projections. Ultrafine aerosol particles (UAP; size <50nm) are considered too small to serve as cloud condensation nuclei conventionally. However, this study provides observational evidence to accompany insights from numerical simulations to support that deep convective clouds (DCCs) over Amazon have strong capability of nucleating UAP from an urban source and forming greater numbers of droplets, because fast drop coalescence in these DCCs reduces drop surface area available for condensation, leading to high vapor supersaturation. The additional droplets subsequently decrease supersaturation and release more condensational latent heating, a dominant contributor to convection intensification,more » whereas enhanced latent heat from ice-related processes plays a secondary role. Therefore, the addition of anthropogenic UAP may play a much greater role in modulating clouds than previously believed over the Amazon region and possibly in other relatively pristine regions such as maritime and forest locations.« less

The EOS CERES Global Cloud Mask

NASA Technical Reports Server (NTRS)

Berendes, T. A.; Welch, R. M.; Trepte, Q.; Schaaf, C.; Baum, B. A.

1996-01-01

To detect long-term climate trends, it is essential to produce long-term and consistent data sets from a variety of different satellite platforms. With current global cloud climatology data sets, such as the International Satellite Cloud Climatology Experiment (ISCCP) or CLAVR (Clouds from Advanced Very High Resolution Radiometer), one of the first processing steps is to determine whether an imager pixel is obstructed between the satellite and the surface, i.e., determine a cloud 'mask.' A cloud mask is essential to studies monitoring changes over ocean, land, or snow-covered surfaces. As part of the Earth Observing System (EOS) program, a series of platforms will be flown beginning in 1997 with the Tropical Rainfall Measurement Mission (TRMM) and subsequently the EOS-AM and EOS-PM platforms in following years. The cloud imager on TRMM is the Visible/Infrared Sensor (VIRS), while the Moderate Resolution Imaging Spectroradiometer (MODIS) is the imager on the EOS platforms. To be useful for long term studies, a cloud masking algorithm should produce consistent results between existing (AVHRR) data, and future VIRS and MODIS data. The present work outlines both existing and proposed approaches to detecting cloud using multispectral narrowband radiance data. Clouds generally are characterized by higher albedos and lower temperatures than the underlying surface. However, there are numerous conditions when this characterization is inappropriate, most notably over snow and ice of the cloud types, cirrus, stratocumulus and cumulus are the most difficult to detect. Other problems arise when analyzing data from sun-glint areas over oceans or lakes over deserts or over regions containing numerous fires and smoke. The cloud mask effort builds upon operational experience of several groups that will now be discussed.

The Devdorak ice-rock avalanche and consequent debris flow from the slope of Mt. Kazbek (Caucasus, Georgia) in 2014

NASA Astrophysics Data System (ADS)

Chernomorets, Sergey; Savernyuk, Elena; Petrakov, Dmitry; Dokukin, Mikhail; Gotsiridze, George; Gavardashvili, Givi; Drobyshev, Valery; Tutubalina, Olga; Zaporozhchenko, Eduard; Kamenev, Nikolay; Kamenev, Vladimir; Kääb, Andreas; Kargel, Jeffrey; Huggel, Christian

2016-04-01

We have studied catastrophic glacial events of 2014 in the Kazbek-Dzhimaray massif, Caucasus Mts., Georgia. The first event is a so called "Kazbek blockage" of the Georgian Military Road, on 17 May 2014, which formed as a result of an ice-rock avalanche onto the Devdorak Glacier, and is similar to blockages which occurred in the same location in the 18th-19th century. The second event is a consequent debris flow on 20 August 2014. In May, June 2014 and September 2015 we conducted three field investigations of the disaster zone, which includes Devdorak Glacier, Amilishka and Kabakhi river valleys, the Terek River valley near the Kabakhi River mouth, and a temporary lake.We analyzed field research data, interpreted SPOT 6, Landsat-8 OLI, Terra ASTER, and Pleiades satellite imagery, as well as post-disaster helicopter imagery. To assess dynamic features of the ice-rock flow on 17 May 2014, we measured valley crossections with Bushnell laser ranger. In 2015 we have marked a 180-m baseline for ground stereosurvey and made a stereopair of the Devdorak glacier terminus from a distance of 700 m. The 17 May 2014 ice-rock avalanche initiated at 4500 m. a.s.l. It collapsed onto the tongue of the Devdorak Glacier which reaches down to 2300 m a.s.l. Downstream of the tongue, the avalanche transformed into an ice-rock "avalanche flow" which blocked the Terek River valley. The traffic on Military Georgian Road (part of E117 highway) which connects Russia with Georgia was stopped. 7 people were killed in their vehicles. The total length of the ice-rock avalanche and the subsequent flow was over 10 km. A temporary lake formed in the Terek river valley, reaching 300 m in length, and over 10 m in depth. For several hours, the lake was threatening another debris flow downstream the Terek river valley. According to field estimates at the Devdorak glacier tongue and in Amilishka, Kabakhi and Terek river valleys, the volume of the transported ice-rock avalanche mass, which deposited in the middle and lower course of the valley below 3000 m a.s.l. was about 2 million cubic metres, while the ice content in the deposits reached 25-30%. It is planned to assess the volume of the trigger mass in the initiation zone later. The flow went along the valley with characteristic superelevations and run-ups, as it moved from one valley side to the other. We identified six superelevaions in fresh deposits, with differences of up to 45 m in flow height on the left and right valley banks. Instrumental measurements of superelevations and subsequent calculations yield the flow velocities of over 200 km/hour. These results lead to a reassessment of similar events which occurred in this valley in 18-19th centuries. Previously the trigger of these events was supposed to be the ice accumulation during surges of Devdorak glacier with subsequent temporary damming of the Amilishka River valley. The analysis of the 2014 event demonstrates that a similar trigger was possible in the past: an ice-rock avalanche onto Devdorak glacier tongue from significantly higher locations. Following the field data analysis, we issued a warning through mass media on 12 August 2014, forecasting a high risk of a new glacial disaster in this site and a new blockage of the Terek River valley and of Military Georgian Road. This forecast came true on 20 August 2014: a glacial debris flow reached the Terek River valley, and partially buried the Dariali hydropower station (under construction), the customs and border control buildings. Three people have been killed. We studied the deposits of this debris flow and morphology of the gully. The deposits entrained by the flow were previously deposited by the ice-rock avalanche of 17 May 2014. The debris flow started after shower rains. The debris flow-gully has a box-like crossection. At the confluence of Amilishka and Chach rivers it reached 30-32 m in width, and eroded the deposits of 17 May 2014 by 7 m. The channel slope at this location was about 7 degrees. Remnant ice in the transit zone has nearly melted by September 2015; however, the ice remains in the deposits near the glacier tongue and in the ice-rock avalanche deposits on the tongue. We have registered the advance of one of the termini of Devdorak Glacier. It moved forward by about 200 m from summer 2014 to September 2015, and became significantly higher. This part of the glacier was overloaded by the ice-rock avalanche deposits which provoked its advance, and should be closely monitored as it can raise the debris flow activity further. The hazard of new ice-rock avalanches and debris flows in the Devdorak gorge remains high. We have developed recommendation on the installation of an early warning system, continuation of glacier hazard monitoring, and suggestions on the construction of a road tunnel to mitigate the risk and avoid casualties in the future.

Physical and Optical/Radiative Characteristics of Aerosol and Cloud Particles in Tropical Cirrus: Importance in Radiation Balance

NASA Technical Reports Server (NTRS)

Pueschel, R. F.; Howard, S. D.; Foster, T. C.; Hallett, J.; Arnott, W. P.; Condon, Estelle P. (Technical Monitor)

1996-01-01

Whether cirrus clouds heat or cool the Earth-atmosphere system depends on the relative importance of the cloud shortwave albedo effect and the cloud thermal greenhouse effect. Both are determined by the distribution of ice condensate with cloud particle size. The microphysics instrument package flown aboard the NASA DC-8 in TOGA/COARE included an ice crystal replicator, a 2D Greyscale Cloud Particle Probe and a Forward Scattering Spectrometer Aerosol Probe. In combination, the electro-optical instruments permitted particle size measurements between 0.5 micrometer and 2.6 millimeter diameter. Ice crystal replicas were used to validate signals from the electrooptical instruments. Both optical and scanning electron microscopy were utilized to analyze aerosol and ice particle replicas between 0.1 micrometer and several 100 micrometer diameter. In first approximation, the combined aerosol-cloud particle spectrum in several clouds followed a power law N alpha D(sup -2.5). Thus, large cloud particles carried most of the condensate mass, while small cloud and aerosol particles determined the surface area. The mechanism of formation of small particles is growth of (hygroscopic, possibly ocean-derived) aerosol particles along the Kohler curves. The concentration of small particles is higher and less variable in space and time, and their tropospheric residence time is longer, than those of large cloud particles because of lower sedimentation velocities. Small particles shift effective cloud particle radii to sizes much smaller than the mean diameter of the cloud particles. This causes an increase in shortwave reflectivity and IR emissivity, and a decrease in transmissivity. Occasionally, the cloud reflectivity increased with altitude (decreasing temperature) stronger than did cloud emissivity, yielding enhanced radiative cooling at higher altitudes. Thus, cirrus produced by deep convection in the tropics may be critical in controlling processes whereby energy from warm tropical oceans is injected to different levels in the atmosphere to subsequently influence not only tropical but mid-latitude climate.

Simultaneous and synergistic profiling of cloud and drizzle properties using ground-based observations

NASA Astrophysics Data System (ADS)

Rusli, Stephanie P.; Donovan, David P.; Russchenberg, Herman W. J.

2017-12-01

Despite the importance of radar reflectivity (Z) measurements in the retrieval of liquid water cloud properties, it remains nontrivial to interpret Z due to the possible presence of drizzle droplets within the clouds. So far, there has been no published work that utilizes Z to identify the presence of drizzle above the cloud base in an optimized and a physically consistent manner. In this work, we develop a retrieval technique that exploits the synergy of different remote sensing systems to carry out this task and to subsequently profile the microphysical properties of the cloud and drizzle in a unified framework. This is accomplished by using ground-based measurements of Z, lidar attenuated backscatter below as well as above the cloud base, and microwave brightness temperatures. Fast physical forward models coupled to cloud and drizzle structure parameterization are used in an optimal-estimation-type framework in order to retrieve the best estimate for the cloud and drizzle property profiles. The cloud retrieval is first evaluated using synthetic signals generated from large-eddy simulation (LES) output to verify the forward models used in the retrieval procedure and the vertical parameterization of the liquid water content (LWC). From this exercise it is found that, on average, the cloud properties can be retrieved within 5 % of the mean truth. The full cloud-drizzle retrieval method is then applied to a selected ACCEPT (Analysis of the Composition of Clouds with Extended Polarization Techniques) campaign dataset collected in Cabauw, the Netherlands. An assessment of the retrieval products is performed using three independent methods from the literature; each was specifically developed to retrieve only the cloud properties, the drizzle properties below the cloud base, or the drizzle fraction within the cloud. One-to-one comparisons, taking into account the uncertainties or limitations of each retrieval, show that our results are consistent with what is derived using the three independent methods.

The Shallow-to-Deep Transition in Convective Clouds During GoAmazon 2014/5

NASA Astrophysics Data System (ADS)

Jensen, M. P.; Gostic, C.; Giangrande, S. E.; Mechem, D. B.; Ghate, V. P.; Toto, T.

2016-12-01

Nearly two years of observations from the ARM Mobile Facility (AMF) deployed at Manacapuru, Brazil during the GOAmazon 2014/5 campaign are analyzed to investigate the environmental conditions controlling the transition from shallow to deep convective clouds. The Active Remote Sensing of Clouds (ARSCL) product, which combines radar and lidar observations to produce best estimates of cloud locations in the vertical column is used to qualitatively define four subsets of convective cloud conditions: 1,2) Transition cases (wet season, dry season), where a period of shallow convective clouds is followed by a period of deep convective clouds and 2) Non-transition cases (wet season, dry season), where shallow convective clouds persist without any subsequent development. For these subsets, observations of the time varying thermodynamic properties of the atmosphere, including the surface heat and radiative fluxes, the profiles of atmospheric state variables, and the ECMWF-derived large-scale advective tendencies, are composited to define averaged properties for each transition state. Initial analysis indicates that the transition state strongly depends on the pre-dawn free-tropospheric humidity, the convective inhibition and surface temperature and humidity with little dependence on the convective available potential energy and surface heat fluxes. The composited environmental thermodynamics are then used to force large-eddy simulations for the four transition states to further evaluate the sensitivity of the transition to the composite thermodynamics versus the importance of larger-scale forcing.

MODIS Collection 6 Clear Sky Restoral (CSR): Filtering Cloud Mast 'Not Clear' Pixels

NASA Technical Reports Server (NTRS)

Meyer, Kerry G.; Platnick, Steven Edward; Wind, Galina; Riedi, Jerome

2014-01-01

Correctly identifying cloudy pixels appropriate for the MOD06 cloud optical and microphysical property retrievals is accomplished in large part using results from the MOD35 1km cloud mask tests (note there are also two 250m subpixel cloud mask tests that can convert the 1km cloudy designations to clear sky). However, because MOD35 is by design clear sky conservative (i.e., it identifies "not clear" pixels), certain situations exist in which pixels identified by MOD35 as "cloudy" are nevertheless likely to be poor retrieval candidates. For instance, near the edge of clouds or within broken cloud fields, a given 1km MODIS field of view (FOV) may in fact only be partially cloudy. This can be problematic for the MOD06 retrievals because in these cases the assumptions of a completely overcast homogenous cloudy FOV and 1-dimensional plane-parallel radiative transfer no longer hold, and subsequent retrievals will be of low confidence. Furthermore, some pixels may be identified by MOD35 as "cloudy" for reasons other than the presence of clouds, such as scenes with thick smoke or lofted dust, and should therefore not be retrieved as clouds. With such situations in mind, a Clear Sky Restoral (CSR) algorithm was introduced in C5 that attempts to identify pixels expected to be poor retrieval candidates. Table 1 provides SDS locations for CSR and partly cloudy (PCL) pixels.

Design and Implementation of a Cloud Computing Adoption Decision Tool: Generating a Cloud Road.

PubMed

Bildosola, Iñaki; Río-Belver, Rosa; Cilleruelo, Ernesto; Garechana, Gaizka

2015-01-01

Migrating to cloud computing is one of the current enterprise challenges. This technology provides a new paradigm based on "on-demand payment" for information and communication technologies. In this sense, the small and medium enterprise is supposed to be the most interested, since initial investments are avoided and the technology allows gradual implementation. However, even if the characteristics and capacities have been widely discussed, entry into the cloud is still lacking in terms of practical, real frameworks. This paper aims at filling this gap, presenting a real tool already implemented and tested, which can be used as a cloud computing adoption decision tool. This tool uses diagnosis based on specific questions to gather the required information and subsequently provide the user with valuable information to deploy the business within the cloud, specifically in the form of Software as a Service (SaaS) solutions. This information allows the decision makers to generate their particular Cloud Road. A pilot study has been carried out with enterprises at a local level with a two-fold objective: to ascertain the degree of knowledge on cloud computing and to identify the most interesting business areas and their related tools for this technology. As expected, the results show high interest and low knowledge on this subject and the tool presented aims to readdress this mismatch, insofar as possible.

Design and Implementation of a Cloud Computing Adoption Decision Tool: Generating a Cloud Road

PubMed Central

Bildosola, Iñaki; Río-Belver, Rosa; Cilleruelo, Ernesto; Garechana, Gaizka

2015-01-01

Migrating to cloud computing is one of the current enterprise challenges. This technology provides a new paradigm based on “on-demand payment” for information and communication technologies. In this sense, the small and medium enterprise is supposed to be the most interested, since initial investments are avoided and the technology allows gradual implementation. However, even if the characteristics and capacities have been widely discussed, entry into the cloud is still lacking in terms of practical, real frameworks. This paper aims at filling this gap, presenting a real tool already implemented and tested, which can be used as a cloud computing adoption decision tool. This tool uses diagnosis based on specific questions to gather the required information and subsequently provide the user with valuable information to deploy the business within the cloud, specifically in the form of Software as a Service (SaaS) solutions. This information allows the decision makers to generate their particular Cloud Road. A pilot study has been carried out with enterprises at a local level with a two-fold objective: to ascertain the degree of knowledge on cloud computing and to identify the most interesting business areas and their related tools for this technology. As expected, the results show high interest and low knowledge on this subject and the tool presented aims to readdress this mismatch, insofar as possible. PMID:26230400

Inferred Primary Compositions of Archean Spherules Formed by the Condensation of an Impact-produced Rock Vapor Cloud, Barberton Greenstone Belt, South Africa

NASA Technical Reports Server (NTRS)

Krull, A. E.; Lowe, D. R.; Byerly, G. R.

2003-01-01

Based on the lunar cratering record, impacts were larger and more frequent on the early Earth than they are today. There is no persevered record of these early terrestrial impacts because rocks of this age have been obliterated by tectonism and erosion. The oldest known evidence of impacts on Earth lies in four beds (S1, S2, S3 and S4) in the Barberton Greenstone Belt (BGB), South Africa, ranging in age from about 3.24 to 3.47 Ga. These beds are composed in large part of sand-sized spherical particles, termed spherules, that are thought to have formed by the condensation of rock vapor clouds ejected above the atmosphere as a result of large impacts. Spherule beds S2 and S3 are both about 20 cm thick where composed entirely of fall-deposited spherules and up to a meter thick where spherules are mixed with locally derived debris. The diameters the bolides have been estimated to be between 20 and 50 km, based on bed thickness, size of the largest spherules, Ir fluence and extraterrestrial Cr.

Reactor-pumped laser facility at DOE's Nevada Test Site

NASA Astrophysics Data System (ADS)

Lipinski, Ronald J.

1994-05-01

The Nevada Test Site (NTS) is one excellent possibility for a laser power beaming site. It is in the low latitudes of the U.S., is in an exceptionally cloud-free area of the southwest, is already an area of restricted access (which enhances safety considerations), and possesses a highly skilled technical team with extensive engineering and research capabilities from underground testing of our nation's nuclear deterrence. The average availability of cloud-free clear line of site to a given point in space is about 84%. With a beaming angle of +/- 60 degree(s) from the zenith, about 52 geostationary-orbit (GEO) satellites could be accessed continuously from NTS. In addition, the site would provide an average view factor of about 10% for orbital transfer from low earth orbit to GEO. One of the major candidates for a long-duration, high- power laser is a reactor-pumped laser being developed by DOE. The extensive nuclear expertise at NTS makes this site a prime candidate for utilizing the capabilities of a rector pumped laser for power beaming. The site then could be used for many dual-use roles such as industrial material processing research, defense testing, and removing space debris.

Spitzer c2d Legacy, Circumstellar Disks around wTT Stars

NASA Astrophysics Data System (ADS)

Wahhaj, Zahed; c2d Legacy Team

2007-05-01

The Spitzer Legacy Project From "Molecular Cores to Planet-forming Disks" conducted a 3.6 to 70um photometric survey of roughly 160 weak- line TTauri Stars (wTTs) and 20 classical TTauri stars (cTTs) in the nearby star-forming regions Chamaeleon, Lupus, Ophiuchus and Taurus. WTTs are so named because they possess weaker H-alpha emission lines signifying weaker disk accretion on to the star than cTTs. The evolution of dust disks around these young stars (Age 10 Myrs) is key to understanding planet formation. From the observed infrared excesses, we infer the presence of circumstellar disks around 12% of wTTs and 75% of cTTs. However, when considering on-cloud sources only, the wTTs disk fraction is 22%, while it is only 6% for off- cloud sources, suggesting an older age for the latter. WTTs, while not discernibly younger than cTTs in age diagnostics, in general have disks which exhibit lower fractional luminosities and larger inner clearings. However, quite a few wTTs systems have fractional disk luminosities as high as cTTs systems. In light of these findings, wTTs seem to be transitional objects between cTTs and debris disks.

Simulations of Polar Stratospheric Clouds and Denitrification Using Laboratory Freezing Rates

NASA Technical Reports Server (NTRS)

Drdla, Katja; Tabazadeh, Azadeh; Gore, Warren J. (Technical Monitor)

2001-01-01

During the 1999-2000 Arctic winter, the SAGE (Stratospheric Aerosol and Gas Experiment) III Ozone Loss and Validation Experiment (SOLVE) provided evidence of widespread solid-phase polar stratospheric clouds (PSCs) accompanied by severe nitrification. Previous simulations have shown that a freezing process occurring at temperatures above the ice frost point is necessary to explain these observations. In this work, the nitric acid freezing rates measured by Salcedo et al. and discussed by Tabazadeh et al. have been examined. These freezing rates have been tested in winter-long microphysical simulations of the 1999-2000 Arctic vortex evolution in order to determine whether they can explain the observations. A range of cases have been explored, including whether the PSC particles are composed of nitric acid dihydrate or trihydrate, whether the freezing process is a bulk process or occurs only on the particle surfaces, and uncertainties in the derived freezing rates. Finally, the possibility that meteoritic debris enhances the freezing rate has also been examined. The results of these simulations have been compared with key PSC and denitrification measurements made by the SOLVE campaign. The cases that best reproduce the measurements will he highlighted, with a discussion of the implications for our understanding of PSCs.

A Three-Body Resonance Confines the Ring-Arcs of Neptune

NASA Astrophysics Data System (ADS)

Showalter, Mark; Lissauer, Jack J.; de Pater, Imke; French, Robert S.

2017-10-01

Two prominent arcs in Neptune's Adams ring have persisted for more than thirty years. Absent active confinement, the arcs would have dissipated in a few years due to Kepler shear. Based on nearly 30 years of astrometry from Voyager and the Hubble Space Telescope, we now find that the orbital semimajor axis of the arcs falls within ~ 10 meters of a strong three-body mean motion resonance, which involves the two nearest moons, Galatea and Larissa. Resonances of comparable strength are typically spaced by several km in the vicinity of the ring, making this particular association unlikely to be a coincidence. Furthermore, each arc falls within the longitudinal boundaries of one of the 39 corotation sites that this resonance creates. Collisionless numerical simulations confirm that the resonance is capable of confining ring material within these corotation sites; more realistic, collisional simulations are in progress. The dynamics appears to be generally similar to that from an earlier model in which the arcs were confined by a two-body resonance with Galatea (Porco, Science 253, 995-1001, 1991). However, subsequent observations have shown that the arcs' mean motion is definitively outside the resonance as originally proposed. Subsequent models have invoked one or more embedded moonlets to confine the arcs, but this new model eliminates the need to invoke additional unseen moonlets. We hypothesize that the arcs comprise debris ejected from an impact into the Adams ring multiple decades ago. Only a fraction of that debris landed precisely in the resonance. The additional arcs imaged by Voyager in 1990 comprise material that orbited close to, but not in, the resonance; that material has dispersed slowly over the subsequent decades, leaving only two arcs that persist to this day.

Cloud Impacts on Pavement Temperature in Energy Balance Models

NASA Astrophysics Data System (ADS)

Walker, C. L.

2013-12-01

Forecast systems provide decision support for end-users ranging from the solar energy industry to municipalities concerned with road safety. Pavement temperature is an important variable when considering vehicle response to various weather conditions. A complex, yet direct relationship exists between tire and pavement temperatures. Literature has shown that as tire temperature increases, friction decreases which affects vehicle performance. Many forecast systems suffer from inaccurate radiation forecasts resulting in part from the inability to model different types of clouds and their influence on radiation. This research focused on forecast improvement by determining how cloud type impacts the amount of shortwave radiation reaching the surface and subsequent pavement temperatures. The study region was the Great Plains where surface solar radiation data were obtained from the High Plains Regional Climate Center's Automated Weather Data Network stations. Road pavement temperature data were obtained from the Meteorological Assimilation Data Ingest System. Cloud properties and radiative transfer quantities were obtained from the Clouds and Earth's Radiant Energy System mission via Aqua and Terra Moderate Resolution Imaging Spectroradiometer satellite products. An additional cloud data set was incorporated from the Naval Research Laboratory Cloud Classification algorithm. Statistical analyses using a modified nearest neighbor approach were first performed relating shortwave radiation variability with road pavement temperature fluctuations. Then statistical associations were determined between the shortwave radiation and cloud property data sets. Preliminary results suggest that substantial pavement forecasting improvement is possible with the inclusion of cloud-specific information. Future model sensitivity testing seeks to quantify the magnitude of forecast improvement.

Partitioning the primary ice formation modes in large eddy simulations of mixed-phase clouds

NASA Astrophysics Data System (ADS)

Hande, Luke B.; Hoose, Corinna

2017-11-01

State-of-the-art aerosol-dependent parameterisations describing each heterogeneous ice nucleation mode (contact, immersion, and deposition ice nucleation), as well as homogeneous nucleation, were incorporated into a large eddy simulation model. Several cases representing commonly occurring cloud types were simulated in an effort to understand which ice nucleation modes contribute the most to total concentrations of ice crystals. The cases include a completely idealised warm bubble, semi-idealised deep convection, an orographic cloud, and a stratiform case. Despite clear differences in thermodynamic conditions between the cases, the results are remarkably consistent between the different cloud types. In all the investigated cloud types and under normal aerosol conditions, immersion freezing dominates and contact freezing also contributes significantly. At colder temperatures, deposition nucleation plays only a small role, and homogeneous freezing is important. To some extent, the temporal evolution of the cloud determines the dominant freezing mechanism and hence the subsequent microphysical processes. Precipitation is not correlated with any one ice nucleation mode, instead occurring simultaneously when several nucleation modes are active. Furthermore, large variations in the aerosol concentration do affect the dominant ice nucleation mode; however, they have only a minor influence on the precipitation amount.

Mars Global Surveyor observations of Martian fretted terrain

USGS Publications Warehouse

Carr, M.H.

2001-01-01

The Martian fretted terrain between latitudes 30?? and 50?? N and between 315?? and 360?? W has been reexamined in light of new Mars Orbiter Camera (MOC) and Mars Orbiter Laser Altimeter (MOLA) data from Mars Global Surveyor. Much of the terrain in the 30??-50?? latitude belt in both hemispheres has a characteristic stippled or pitted texture at MOC (1.5 m) scale. The texture appears to result from partial removal of a formerly smooth, thin deposit as a result of sublimation and deflation. A complex history of deposition and exhumation is indicated by remnants of a former, thicker cover of layered deposits. In some hollows and on some slopes, particularly those facing the pole, are smooth textured deposits outlined by an outward facing escarpment. Throughout the study area are numerous escarpments with debris flows at their base. The escarpments typically have slopes in the 20??-30?? range. At the base of the escarpment is commonly a deposit with striae oriented at right angles to the escarpment. Outside this deposit is the main debris apron with a surface that typically slopes 2??-3?? and complex surface textures suggestive of compression, sublimation, and deflation. The presence of undeformed impact craters indicates that the debris flows are no longer forming. Fretted valleys contain lineated fill and are poorly graded. They likely form from fluvial valleys that were initially like those elsewhere on the planet but were subsequently widened and filled by the same mass-wasting processes that formed the debris aprons. Slope reversals indicate that downvalley flow of the lineated fill is minor. The ubiquitous presence of breaks in slope formed by mass wasting and the complex surface textures that result from mass wasting, deflation, and sublimation decreases the recognizability of the shorelines formerly proposed for this area.

Radar evidence for ice in lobate debris aprons in the mid- latitudes of Mars

NASA Astrophysics Data System (ADS)

Plaut, J. J.; Holt, J. W.; Safaeinili, A.; Head, J. W.; Phillips, R. J.; Seu, R.

2008-12-01

Martian "lobate debris aprons" (LDAs) are masses of material 100s of m thick up to 10s of km wide that occur adjacent to escarpments in certain mid-latitude regions of Mars. Their morphology has led many workers to hypothesize that ice played an important role in their formation and subsequent evolution. Data from the Shallow Radar (SHARAD) instrument on the Mars Reconnaissance Orbiter indicate that LDAs indeed consist predominantly of ice. SHARAD signals penetrate the LDA material to depths up to 1 km. A reflection is typically observed at a time delay consistent with detection of an interface between the LDA material and the pre-depositional substrate. The echo strength of the basal reflections is strong, indicating minimal attenuation of the signal, which is consistent with a water-ice-dominated composition. The largest populations of ice-cored LDAs are in the Deuteronilus Mensae (40-51° N, 14-35° E) and Eastern Hellas (40-46° N, 100- 108° E) areas. At these latitudes, water ice is unstable at the surface. LDAs appear to be mantled by a relatively thin (<10 m) debris layer that protects the ice core from sublimation. Mass wasting of slopes of massifs, valley and crater walls maintains this debris mantle and explains the local preservation of LDAs adjacent to these slopes. LDAs are likely the remnants of much larger ice sheets and glaciers from an epoch in Martian history when substantial precipitation occurred at the mid-latitudes. The water ice currently preserved in LDAs likely represents the largest reservoir of near surface H2O outside of the polar regions. Their presence at the mid-latitudes make them intriguing targets for in situ exploration and possible resource utilization.

Morphological analysis of hummocks in debris avalanche deposits using UAS-derived high-definition topographic data

NASA Astrophysics Data System (ADS)

Hayakawa, Yuichi S.; Obanawa, Hiroyuki; Yoshida, Hidetsugu; Naruhashi, Ryutaro; Okumura, Koji; Zaiki, Masumi

2016-04-01

Debris avalanche caused by sector collapse of a volcanic mountain often forms depositional landforms with characteristic surface morphology comprising hummocks. Geomorphological and sedimentological analyses of debris avalanche deposits (DAD) at the northeastern face of Mt. Erciyes in central Turkey have been performed to investigate the mechanisms and processes of the debris avalanche. The morphometry of hummocks provides an opportunity to examine the volumetric and kinematic characteristics of the DAD. Although the exact age has been unknown, the sector collapse of this DAD was supposed to have occurred in the late Pleistocene (sometime during 90-20 ka), and subsequent sediment supply from the DAD could have affected ancient human activities in the downstream basin areas. In order to measure detailed surface morphology and depositional structures of the DAD, we apply structure-from-motion multi-view stereo (SfM-MVS) photogrammetry using unmanned aerial system (UAS) and a handheld camera. The UAS, including small unmanned aerial vehicle (sUAV) and a digital camera, provides low-altitude aerial photographs to capture surface morphology for an area of several square kilometers. A high-resolution topographic data, as well as an orthorectified image, of the hummocks were then obtained from the digital elevation model (DEM), and the geometric features of the hummocks were examined. A handheld camera is also used to obtain photographs of outcrop face of the DAD along a road to support the seimentological investigation. The three-dimensional topographic models of the outcrop, with a panoramic orthorectified image projected on a vertical plane, were obtained. This data enables to effectively describe sedimentological structure of the hummock in DAD. The detailed map of the DAD is also further examined with a regional geomorphological map to be compared with other geomorphological features including fluvial valleys, terraces, lakes and active faults.

Assessing the Potential Impact of the 2015-2016 El Niño on the California Rim Fire Burn Scar Through Debris Flow Hazard Mapping

NASA Astrophysics Data System (ADS)

Larcom, S.; Grigsby, S.; Ustin, S.

2015-12-01

Wildfires are a perennial issue for California, and the current record-breaking drought is exacerbating the potential problems for the state. Fires leave behind burn scars characterized by diminished vegetative cover and abundant bare soil, and these areas are especially susceptible to storm events that pose an elevated risk of debris flows and sediment-rich sheet wash. This study focused on the 2013 Rim Fire that devastated significant portions of Stanislaus National Forest and Yosemite National Park, and utilized readily available NASA JPL SRTM elevation data and AVIRIS spectral imaging data to construct a debris flow hazard map that assesses mass wasting risk for the Rim Fire burn scar. This study consisted entirely of remotely sensed data, which was processed in software programs such as ENVI, GRASS GIS, ArcMap, and Google Earth. Parameters that were taken into consideration when constructing this map include hill slope (greater than 30 percent rise), burn severity (assessed by calculating NDVI), and erodibility of the soil (by comparing spectral reflectance of AVIRIS images with the reference spectra of illite). By calculating percent of total burn area, 6% was classified as low risk, 55% as medium risk, and 39% as high risk. In addition, this study assessed the importance of the 2015-2016 El Niño, which is projected to be one of the strongest on record, by studying historic rainfall records and storm events of past El Niño's. Hydrological and infrastructural problems that could be caused by short-term convective or long-term synoptic storms and subsequent debris flows were explored as well.

Importance of including ammonium sulfate ((NH4)2SO4) aerosols for ice cloud parameterization in GCMs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bhattacharjee, P. S.; Sud, Yogesh C.; Liu, Xiaohong

2010-02-22

A common deficiency of many cloud-physics parameterizations including the NASA’s microphysics of clouds with aerosol- cloud interactions (hereafter called McRAS-AC) is that they simulate less (larger) than the observed ice cloud particle number (size). A single column model (SCM) of McRAS-AC and Global Circulation Model (GCM) physics together with an adiabatic parcel model (APM) for ice-cloud nucleation (IN) of aerosols were used to systematically examine the influence of ammonium sulfate ((NH4)2SO4) aerosols, not included in the present formulations of McRAS-AC. Specifically, the influence of (NH4)2SO4 aerosols on the optical properties of both liquid and ice clouds were analyzed. First anmore » (NH4)2SO4 parameterization was included in the APM to assess its effect vis-à-vis that of the other aerosols. Subsequently, several evaluation tests were conducted over the ARM-SGP and thirteen other locations (sorted into pristine and polluted conditions) distributed over marine and continental sites with the SCM. The statistics of the simulated cloud climatology were evaluated against the available ground and satellite data. The results showed that inclusion of (NH4)2SO4 in the SCM made a remarkable improvement in the simulated effective radius of ice clouds. However, the corresponding ice-cloud optical thickness increased more than is observed. This can be caused by lack of cloud advection and evaporation. We argue that this deficiency can be mitigated by adjusting the other tunable parameters of McRAS-AC such as precipitation efficiency. Inclusion of ice cloud particle splintering introduced through well- established empirical equations is found to further improve the results. Preliminary tests show that these changes make a substantial improvement in simulating the cloud optical properties in the GCM, particularly by simulating a far more realistic cloud distribution over the ITCZ.« less

The Effects of an Absorbing Smoke Layer on MODIS Marine Boundary Layer Cloud Optical Property Retrievals and Radiative Forcing

NASA Technical Reports Server (NTRS)

Meyer, Kerry; Platnick, Steven

2012-01-01

Clouds, aerosols, and their interactions are widely considered to be key uncertainty components in our current understanding of the Earth's atmosphere and radiation budget. The work presented here is focused on the quasi-permanent marine boundary layer . (MBL) clouds off the southern Atlantic coast of Africa and the effects on MODIS cloud optical property retrievals (MOD06) of an overlying absorbing smoke layer. During much of August and September, a persistent smoke layer resides over this region, produced from extensive biomass burning throughout the southern African savanna. The resulting absorption, which increases with decreasing wavelength, potentially introduces biases into the MODIS cloud optical property retrievals of the underlying MBL clouds. This effect is more pronounced in the cloud optical thickness retrievals, which over ocean are derived from the wavelength channel centered near 0.86 micron (effective particle size retrievals are derived from the longer-wavelength near-IR channels at 1.6, 2.1, and 3.7 microns). Here, the spatial distributions of the scalar statistics of both the cloud and aerosol layers are first determined from the CALIOP 5 km layer products. Next, the MOD06 look-up tables (LUTs) are adjusted by inserting an absorbing smoke layer of varying optical thickness over the cloud. Retrievals are subsequently performed for a subset of MODIS pixels collocated with the CALIOP ground track, using smoke optical thickness from the CALIOP 5km aerosol layer product to select the appropriate LUT. The resulting differences in cloud optical property retrievals due to the inclusion of the smoke layer in the LUTs will be examined. In addition, the direct radiative forcing of this smoke layer will be investigated from the perspective of the cloud optical property retrieval differences.

The Relationships Between Insoluble Precipitation Residues, Clouds, and Precipitation Over California's Southern Sierra Nevada During Winter Storms

NASA Technical Reports Server (NTRS)

Creamean, Jessie M.; White, Allen B.; Minnis, Patrick; Palikonda, Rabindra; Spangenberg, Douglas A.; Prather, Kimberly A.

2016-01-01

Ice formation in orographic mixed-phase clouds can enhance precipitation and depends on the type of aerosols that serve as ice nucleating particles (INP). The resulting precipitation from these clouds is a viable source of water, especially for regions such as the California Sierra Nevada. Thus, a better understanding of the sources of INP that impact orographic clouds is important for assessing water availability in California. This study presents a multi-site, multi-year analysis of single particle insoluble residues in precipitation samples that likely influenced cloud ice and precipitation formation above Yosemite National Park. Dust and biological particles represented the dominant fraction of the residues (64% on average). Cloud glaciation, determined using GOES satellite observations, not only depended on high cloud tops (greater than 6.2 km) and low temperatures (less than -26 C), but also on the composition of the dust and biological residues. The greatest prevalence of ice-phase clouds occurred in conjunction with biologically-rich residues and mineral dust rich in calcium, followed by iron and aluminosilicates. Dust and biological particles are known to be efficient INP, thus these residues are what likely influenced ice formation in clouds above the sites and subsequent precipitation quantities reaching the surface during events with similar meteorology. The goal of this study is to use precipitation chemistry information to gain a better understanding of the potential sources of INP in the south-central Sierra Nevada, where cloud-aerosol-precipitation interactions are under-studied and where mixed-phase orographic clouds represent a key element in the generation of precipitation and thus the water supply in California.

Role of Gravity Waves in Determining Cirrus Cloud Properties

NASA Technical Reports Server (NTRS)

OCStarr, David; Singleton, Tamara; Lin, Ruei-Fong

2008-01-01

Cirrus clouds are important in the Earth's radiation budget. They typically exhibit variable physical properties within a given cloud system and from system to system. Ambient vertical motion is a key factor in determining the cloud properties in most cases. The obvious exception is convectively generated cirrus (anvils), but even in this case, the subsequent cloud evolution is strongly influenced by the ambient vertical motion field. It is well know that gravity waves are ubiquitous in the atmosphere and occur over a wide range of scales and amplitudes. Moreover, researchers have found that inclusion of statistical account of gravity wave effects can markedly improve the realism of simulations of persisting large-scale cirrus cloud features. Here, we use a 1 -dimensional (z) cirrus cloud model, to systematically examine the effects of gravity waves on cirrus cloud properties. The model includes a detailed representation of cloud microphysical processes (bin microphysics and aerosols) and is run at relatively fine vertical resolution so as to adequately resolve nucleation events, and over an extended time span so as to incorporate the passage of multiple gravity waves. The prescribed gravity waves "propagate" at 15 m s (sup -1), with wavelengths from 5 to 100 km, amplitudes range up to 1 m s (sup -1)'. Despite the fact that the net gravity wave vertical motion forcing is zero, it will be shown that the bulk cloud properties, e.g., vertically-integrated ice water path, can differ quite significantly from simulations without gravity waves and that the effects do depend on the wave characteristics. We conclude that account of gravity wave effects is important if large-scale models are to generate realistic cirrus cloud property climatology (statistics).

Importance of formaldehyde in cloud chemistry

NASA Technical Reports Server (NTRS)

Adewuyi, Y. G.; Cho, S.-Y.; Tsay, R.-P.; Carmichael, G. R.

1984-01-01

A physical-chemical model which is an extension of that of Hong and Carmichael (1983) is used to investigate the role of formaldehyde in cloud chemistry. This model takes into account the mass transfer of SO2, O3, NH3, HNO3, H2O2, CO2, HCl, HCHO, O2, OH and HO2 into cloud droplets and their subsequent chemical reactions. The model is used to assess the importance of S(IV)-HCHO adduct formation, the reduction of H2O2 by HCHO, HCHO-free radical interactions, and the formation of HCOOH in the presence of HCHO in cloud droplets. Illustrative calculations indicate that the presence of HCHO inhibits sulfate production rate in cloud droplets. The direct inhibition of sulfate production rate in cloudwater due to nucleophilic addition of HSO3(-) to HCHO(aq) to form hydroxymethanesulfonate is generally low for concentrations of HCHO typical of ambient air. However, inhibition of sulfate production due to formaldehyde-free radical interactions in solution can be important. These formaldehyde-free radical reactions can also generate appreciable quantities of formic acid.

Secondary organic aerosol formation through cloud processing of aromatic VOCs

NASA Astrophysics Data System (ADS)

Herckes, P.; Hutchings, J. W.; Ervens, B.

2010-12-01

Field observations have shown substantial concentrations (20-5,500 ng L-1) of aromatic volatile organic compounds (VOC) in cloud droplets. The potential generation of secondary organic aerosol mass through the processing of these anthropogenic VOCs was investigated through laboratory and modeling studies. Under simulated atmospheric laboratory conditions, in idealized solutions, benzene, toluene, ethylbenzene, and xylene (BTEX) degraded quickly in the aqueous phase. The degradation process yielded less volatile products which would contribute to new aerosol mass upon cloud evaporation. However, when realistic cloud solutions containing natural organic matter were used in the experiments, the reaction rates decreased with increasing organic carbon content. Kinetic data derived from these experiments were used as input to a multiphase box model in order to evaluate the secondary organic aerosol (SOA) mass formation potential of cloud processing of BTEX. Model results will be presented that quantify the SOA amounts from these aqueous phase pathways. The efficiency of this multiphase SOA source will be compared to SOA yields from the same aromatics as treated in traditional SOA models that are restricted to gas phase oxidation and subsequent condensation on particles.

Characteristics of magnetised plasma flow around stationary and expanding magnetic clouds

NASA Astrophysics Data System (ADS)

Dalakishvili, Giorgi

Studies of interplanetary magnetic clouds have shown that the characteristics of the region ahead of these objects, which are moving away from the Sun in the solar wind, play a role in determining their geo-efficiency, i.e. the kind and the degree of their effects on the Earth environment. Therefore, our main goal is to model and study the plasma parameters in the vicinity of interplanetary magnetic clouds. To this end we present a model in which the magnetic clouds are immersed in a magnetised plasma flow with a homogeneous magnetic field. We first calculate the resulting distortion of the external magnetic field and then determine the plasma velocity by employing the frozen-in condition. Subsequently, the plasma density and pressure are expressed as functions of the magnetic field and the velocity field. The plasma flow parameters are determined by solving the time-independent ideal MHD equations for both the stationary regime and for the case of an expand-ing cylindrical magnetic cloud, thus extending previous results that appeared in the literature.

Electroacupuncture Promotes Remyelination after Cuprizone Treatment by Enhancing Myelin Debris Clearance

PubMed Central

Zhu, Keying; Sun, Jingxian; Kang, Zheng; Zou, Zaofeng; Wu, Gencheng; Wang, Jun

2017-01-01

Promoting remyelination is crucial for patients with demyelinating diseases including multiple sclerosis. However, it is still a circuitous conundrum finding a practical remyelinating therapy. Electroacupuncture (EA), originating from traditional Chinese medicine (TCM), has been widely used to treat CNS diseases all over the world, but the role of EA in demyelinating diseases is barely known. In this study, we examined the remyelinating properties and mechanisms of EA in cuprizone-induced demyelinating model, a CNS demyelinating murine model of multiple sclerosis. By feeding C57BL/6 mice with chow containing 0.2% cuprizone for 5 weeks, we successfully induce demyelination as proved by weight change, beam test, pole test, histomorphology, and Western Blot. EA treatment significantly improves the neurobehavioral performance at week 7 (2 weeks after withdrawing cuprizone chow). RNA-seq and RT-PCR results reveal up-regulated expression of myelin-related genes, and the expression of myelin associated protein (MBP, CNPase, and O4) are also increased after EA treatment, indicating therapeutic effect of EA on cuprizone model. It is widely acknowledged that microglia exert phagocytic effect on degraded myelin debris and clear these detrimental debris, which is a necessary process for subsequent remyelination. We found the remyelinating effect of EA is associated with enhanced clearance of degraded myelin debris as detected by dMBP staining and red oil O staining. Our further studies suggest that more microglia assemble in demyelinating area (corpus callosum) during the process of EA treatment, and cells inside corpus callosum are mostly in a plump, ameboid, and phagocytic shape, quite different from the ramified cells outside corpus callosum. RNA-seq result also unravels that most genes relating to positive regulation of phagocytosis (GO:0050766) are up-regulated, indicating enhanced phagocytic process after EA treatment. During the process of myelin debris clearance, microglia tend to change their phenotype toward M2 phenotype. Thus, we also probed into the phenotype of microglia in our study. Immuno-staining results show increased expression of CD206 and Arg1, and the ratio of CD206/CD16/32 are also higher in EA group. In conclusion, these results demonstrate for the first time that EA enhances myelin debris removal from activated microglia after demyelination, and promotes remyelination. PMID:28119561

Relating large-scale subsidence to convection development in Arctic mixed-phase marine stratocumulus

NASA Astrophysics Data System (ADS)

Young, Gillian; Connolly, Paul J.; Dearden, Christopher; Choularton, Thomas W.

2018-02-01

Large-scale subsidence, associated with high-pressure systems, is often imposed in large-eddy simulation (LES) models to maintain the height of boundary layer (BL) clouds. Previous studies have considered the influence of subsidence on warm liquid clouds in subtropical regions; however, the relationship between subsidence and mixed-phase cloud microphysics has not specifically been studied. For the first time, we investigate how widespread subsidence associated with synoptic-scale meteorological features can affect the microphysics of Arctic mixed-phase marine stratocumulus (Sc) clouds. Modelled with LES, four idealised scenarios - a stable Sc, varied droplet (Ndrop) or ice (Nice) number concentrations, and a warming surface (representing motion southwards) - were subjected to different levels of subsidence to investigate the cloud microphysical response. We find strong sensitivities to large-scale subsidence, indicating that high-pressure systems in the ocean-exposed Arctic regions have the potential to generate turbulence and changes in cloud microphysics in any resident BL mixed-phase clouds.Increased cloud convection is modelled with increased subsidence, driven by longwave radiative cooling at cloud top and rain evaporative cooling and latent heating from snow growth below cloud. Subsidence strengthens the BL temperature inversion, thus reducing entrainment and allowing the liquid- and ice-water paths (LWPs, IWPs) to increase. Through increased cloud-top radiative cooling and subsequent convective overturning, precipitation production is enhanced: rain particle number concentrations (Nrain), in-cloud rain mass production rates, and below-cloud evaporation rates increase with increased subsidence.Ice number concentrations (Nice) play an important role, as greater concentrations suppress the liquid phase; therefore, Nice acts to mediate the strength of turbulent overturning promoted by increased subsidence. With a warming surface, a lack of - or low - subsidence allows for rapid BL turbulent kinetic energy (TKE) coupling, leading to a heterogeneous cloud layer, cloud-top ascent, and cumuli formation below the Sc cloud. In these scenarios, higher levels of subsidence act to stabilise the Sc layer, where the combination of these two forcings counteract one another to produce a stable, yet dynamic, cloud layer.

Debris thickness patterns on debris-covered glaciers

NASA Astrophysics Data System (ADS)

Anderson, Leif S.; Anderson, Robert S.

2018-06-01

Many debris-covered glaciers have broadly similar debris thickness patterns: surface debris thickens and tends to transition from convex- to concave-up-down glacier. We explain this pattern using theory (analytical and numerical models) paired with empirical observations. Down glacier debris thickening results from the conveyor-belt-like nature of the glacier surface in the ablation zone (debris can typically only be added but not removed) and from the inevitable decline in ice surface velocity toward the terminus. Down-glacier thickening of debris leads to the reduction of sub-debris melt and debris emergence toward the terminus. Convex-up debris thickness patterns occur near the up-glacier end of debris covers where debris emergence dominates (ablation controlled). Concave-up debris thickness patterns occur toward glacier termini where declining surface velocities dominate (velocity controlled). A convex-concave debris thickness profile inevitably results from the transition between ablation-control and velocity-control down-glacier. Debris thickness patterns deviating from this longitudinal shape are most likely caused by changes in hillslope debris supply through time. By establishing this expected debris thickness pattern, the effects of climate change on debris cover can be better identified.

Phase B: Final definition and preliminary design study for the initial Atmospheric Cloud Physics Laboratory (ACPL), a spacelab mission payload

NASA Technical Reports Server (NTRS)

1976-01-01

A preliminary identification of the Supporting Research and Technology (SR&T) necessary during the planned evolution of atmospheric cloud physics is discussed. All requirements are for subsequent flights over its expected ten year lifetime. Those components identified as requiring some SR&T work prior to inclusion are listed. A data sheet is included for each item, briefly justifying the need, giving general objectives for the proposed development effort and identifying approximate schedule requirements on the program.

Cloud Forming Potential of Aerosol from Light-duty Gasoline Direct Injection Vehicles

DOT National Transportation Integrated Search

2017-12-01

In this study, we evaluate the hygroscopicity and droplet kinetics of fresh and aged emissions from new generation gasoline direct injector engines retrofitted with a gasoline particulate filter (GPF). Furthermore, ageing and subsequent secondary aer...

Differences in Reservoir Bathymetry, Area, and Capacity Between December 20-22, 2005, and June 16-19, 2008, for Lower Taum Sauk Reservoir, Reynolds County, Missouri

USGS Publications Warehouse

Wilson, Gary L.; Richards, Joseph M.

2008-01-01

On December 14, 2005, the embankment of the upper reservoir at the Taum Sauk pump storage facility, Reynolds County, Missouri, catastrophically failed and flooded the East Fork Black River, depositing debris and sediment in Johnson's Shut-Ins State Park, the lower Taum Sauk Reservoir, and downstream in the Black River (location map). A bathymetric survey conducted December 20-22, 2005, documented the bathymetry of the lower Taum Sauk Reservoir after the upper reservoir failure (Rydlund, 2006). After subsequent excavation of sediment and debris from the lower reservoir by Ameren Union Electric (UE), the U.S. Geological Survey (USGS), in collaboration with Roux Associates Inc., conducted a bathymetric survey of the lower Taum Sauk Reservoir on June 16-19, 2008, to prepare a current (2008) bathymetric map (fig. 1) for the lower reservoir, establish a current (2008) elevation-area and capacity table, and determine reservoir area and capacity differences between the 2005 and 2008 bathymetric surveys.

Fires, storms, and water supplies: a case of compound extremes?

NASA Astrophysics Data System (ADS)

Sheridan, G. J.; Nyman, P.; Langhans, C.; Jones, O.; Lane, P. N.

2013-12-01

Intense rainfall events following fire can wash sediment and ash into streams and reservoirs, contaminating water supplies for cities and towns. Post fire flooding and debris flows damage infrastructure and endanger life. These kinds of risks which are associated with a combination of two or more events (which may or may not be extreme when occurring independently) are an example of what the IPCC recently referred to as ';compound extremes'. Detailed models exist for modeling fire and erosion events separately, however there have been few attempts to integrate these models so as to estimate the water quality and infrastructure risks associated with combined fire and rainfall regimes. This presentation will articulate the issues associated with modeling the compound effects of fire and subsequent rainfall events on erosion, debris flows and water quality, and will describe and contrast several new approaches to modeling this problem developed and applied to SE Australian fire prone landscapes under the influence of climate change.

Risk and Vulnerability Analysis of Satellites Due to MM/SD with PIRAT

NASA Astrophysics Data System (ADS)

Kempf, Scott; Schafer, Frank Rudolph, Martin; Welty, Nathan; Donath, Therese; Destefanis, Roberto; Grassi, Lilith; Janovsky, Rolf; Evans, Leanne; Winterboer, Arne

2013-08-01

Until recently, the state-of-the-art assessment of the threat posed to spacecraft by micrometeoroids and space debris was limited to the application of ballistic limit equations to the outer hull of a spacecraft. The probability of no penetration (PNP) is acceptable for assessing the risk and vulnerability of manned space mission, however, for unmanned missions, whereby penetrations of the spacecraft exterior do not necessarily constitute satellite or mission failure, these values are overly conservative. The newly developed software tool PIRAT (Particle Impact Risk and Vulnerability Analysis Tool) has been developed based on the Schäfer-Ryan-Lambert (SRL) triple-wall ballistic limit equation (BLE), applicable for various satellite components. As a result, it has become possible to assess the individual failure rates of satellite components. This paper demonstrates the modeling of an example satellite, the performance of a PIRAT analysis and the potential for subsequent design optimizations with respect of micrometeoroid and space debris (MM/SD) impact risk.

TMI-2 (Three Mile Island Unit 2) core region defueling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rodabaugh, J.M.; Cowser, D.K.

1988-01-01

In July of 1982, a video camera was inserted into the Three Mile Island Unit 2 reactor vessel providing the first visual evidence of core damage. This inspection, and numerous subsequent data acquisition tasks, revealed a central void /approx/1.5 m (5 ft) deep. This void region was surrounded by partial length fuel assemblies and ringed on the periphery by /approx/40 full-length, but partial cross-section, fuel assemblies. All of the original 177 fuel assemblies exhibited signs of damage. The bottom of the void cavity was covered with a bed of granular rubble, fuel assembly upper end fittings, control rod spiders, fuelmore » rod fragments, and fuel pellets. It was obvious that the normal plant refueling system not suitable for removing the damaged core. A new system of defueling tools and equipment was necessary to perform this task. Design of the new system was started immediately, followed by >1 yr of fabrication. Delivery and checkout of the defueling system occurred in mid-1985. Actual defueling was initiated in late 1985 with removal of the debris bed at the bottom of the core void. Obstructions to the debris, such as end fittings and fuel rod fragments ere removed first; then /approx/23,000 kg (50,000lb) of granular debris was quickly loaded into canisters. Core region defueling was completed in late 1987, /approx/2 yr after it was initiated.« less

Biotoxicity and bioavailability of hydrophobic organic compounds solubilized in nonionic surfactant micelle phase and cloud point system.

PubMed

Pan, Tao; Liu, Chunyan; Zeng, Xinying; Xin, Qiao; Xu, Meiying; Deng, Yangwu; Dong, Wei

2017-06-01

A recent work has shown that hydrophobic organic compounds solubilized in the micelle phase of some nonionic surfactants present substrate toxicity to microorganisms with increasing bioavailability. However, in cloud point systems, biotoxicity is prevented, because the compounds are solubilized into a coacervate phase, thereby leaving a fraction of compounds with cells in a dilute phase. This study extends the understanding of the relationship between substrate toxicity and bioavailability of hydrophobic organic compounds solubilized in nonionic surfactant micelle phase and cloud point system. Biotoxicity experiments were conducted with naphthalene and phenanthrene in the presence of mixed nonionic surfactants Brij30 and TMN-3, which formed a micelle phase or cloud point system at different concentrations. Saccharomyces cerevisiae, unable to degrade these compounds, was used for the biotoxicity experiments. Glucose in the cloud point system was consumed faster than in the nonionic surfactant micelle phase, indicating that the solubilized compounds had increased toxicity to cells in the nonionic surfactant micelle phase. The results were verified by subsequent biodegradation experiments. The compounds were degraded faster by PAH-degrading bacterium in the cloud point system than in the micelle phase. All these results showed that biotoxicity of the hydrophobic organic compounds increases with bioavailability in the surfactant micelle phase but remains at a low level in the cloud point system. These results provide a guideline for the application of cloud point systems as novel media for microbial transformation or biodegradation.

IceCube: CubeSat 883-GHz Radiometry for Future Ice Cloud Remote Sensing

NASA Technical Reports Server (NTRS)

Wu, Dongliang; Esper, Jaime; Ehsan, Negar; Johnson, Thomas; Mast, William; Piepmeier, Jeffery R.; Racette, Paul E.

2015-01-01

Ice clouds play a key role in the Earth's radiation budget, mostly through their strong regulation of infrared radiation exchange. Accurate observations of global cloud ice and its distribution have been a challenge from space, and require good instrument sensitivities to both cloud mass and microphysical properties. Despite great advances from recent spaceborne radar and passive sensors, uncertainty of current ice water path (IWP) measurements is still not better than a factor of 2. Submillimeter (submm) wave remote sensing offers great potential for improving cloud ice measurements, with simultaneous retrievals of cloud ice and its microphysical properties. The IceCube project is to enable this cloud ice remote sensing capability in future missions, by raising 874-GHz receiver technology TRL from 5 to 7 in a spaceflight demonstration on 3-U CubeSat in a low Earth orbit (LEO) environment. The NASAs Goddard Space Flight Center (GSFC) is partnering with Virginia Diodes Inc (VDI) on the 874-GHz receiver through its Vector Network Analyzer (VNA) extender module product line, to develop an instrument with precision of 0.2 K over 1-second integration and accuracy of 2.0 K or better. IceCube is scheduled to launch to and subsequent release from the International Space Station (ISS) in mid-2016 for nominal operation of 28 plus days. We will present the updated design of the payload and spacecraft systems, as well as the operation concept. We will also show the simulated 874-GHz radiances from the ISS orbits and cloud scattering signals as expected for the IceCube cloud radiometer.

Star formation induced by cloud-cloud collisions and galactic giant molecular cloud evolution

NASA Astrophysics Data System (ADS)

Kobayashi, Masato I. N.; Kobayashi, Hiroshi; Inutsuka, Shu-ichiro; Fukui, Yasuo

2018-05-01

Recent millimeter/submillimeter observations towards nearby galaxies have started to map the whole disk and to identify giant molecular clouds (GMCs) even in the regions between galactic spiral structures. Observed variations of GMC mass functions in different galactic environments indicates that massive GMCs preferentially reside along galactic spiral structures whereas inter-arm regions have many small GMCs. Based on the phase transition dynamics from magnetized warm neutral medium to molecular clouds, Kobayashi et al. (2017, ApJ, 836, 175) proposes a semi-analytical evolutionary description for GMC mass functions including a cloud-cloud collision (CCC) process. Their results show that CCC is less dominant in shaping the mass function of GMCs than the accretion of dense H I gas driven by the propagation of supersonic shock waves. However, their formulation does not take into account the possible enhancement of star formation by CCC. Millimeter/submillimeter observations within the Milky Way indicate the importance of CCC in the formation of star clusters and massive stars. In this article, we reformulate the time-evolution equation largely modified from Kobayashi et al. (2017, ApJ, 836, 175) so that we additionally compute star formation subsequently taking place in CCC clouds. Our results suggest that, although CCC events between smaller clouds are more frequent than the ones between massive GMCs, CCC-driven star formation is mostly driven by massive GMCs ≳ 10^{5.5} M_{⊙} (where M⊙ is the solar mass). The resultant cumulative CCC-driven star formation may amount to a few 10 percent of the total star formation in the Milky Way and nearby galaxies.

Effects of Cloud Formation on the Speciation of Glyoxal and Methylglyoxal Hydrates and Polymers in Aerosols

NASA Astrophysics Data System (ADS)

Houghton, K. A.; Goh, P.; Spangler, R.; Schweitzer, W.; Khaled, K. A., Jr.; Berry, J.; Van Wyngarden, A. L.

2017-12-01

During cloud formation, atmospheric aerosols take up large quantities of water; the ensuing, rapid changes in water content and acidity may cause organic species within these aerosols to undergo various reactions such as hydration, hydrolysis, and/or polymerization. Glyoxal and methylglyoxal are among the most common organic molecules found within atmospheric aerosols, and prior experimental work has demonstrated that their speciation is altered during cloud processing. Due to the low water content of atmospheric aerosols, organics such as glyoxal and methylglyoxal are suspected to be significantly polymerized before cloud formation, as supported by the observation of polymers in ambient aerosols. Some of these polymerization reactions may be reversible; thus, these polymers may be subject to decomposition during cloud formation. The subsequent changes in the speciation of glyoxal and methylglyoxal polymers following cloud processing may alter the climate forcing properties of that aerosol population. The details of which polymers decompose and whether these decomposition reactions occur with sufficient speed to achieve equilibrium during the average lifetime of a cloud droplet remain unclear. Here, we use high resolution quadrupole mass spectrometry to investigate the kinetics of glyoxal and methylglyoxal speciation reactions after dilution, simulating the effects of cloud droplet formation on aerosol particles. Our data reveal that after dilution, polymers (up to the pentamer and octamer for glyoxal and methylglyoxal, respectively) persist in solution for more than 90 minutes. Furthermore, polymer speciation continues to change for hours after dilution, indicating that kinetics of at least some polymer interconversion reactions are slow with respect to a typical cloud droplet lifetime.

A Bispectral Composite Threshold Approach for Automatic Cloud Detection in VIIRS Imagery

NASA Technical Reports Server (NTRS)

LaFontaine Frank J.; Jedlovec, Gary J.

2015-01-01

The detection of clouds in satellite imagery has a number of important applications in weather and climate studies. The presence of clouds can alter the energy budget of the Earth-atmosphere system through scattering and absorption of shortwave radiation and the absorption and re-emission of infrared radiation at longer wavelengths. The scattering and absorption characteristics of clouds vary with the microphysical properties of clouds, hence the cloud type. Thus, detecting the presence of clouds over a region in satellite imagery is important in order to derive atmospheric or surface parameters that give insight into weather and climate processes. For many applications however, clouds are a contaminant whose presence interferes with retrieving atmosphere or surface information. In these cases, is important to isolate cloud-free pixels, used to retrieve atmospheric thermodynamic information or surface geophysical parameters, from cloudy ones. This abstract describes an application of a two-channel bispectral composite threshold (BCT) approach applied to VIIRS imagery. The simplified BCT approach uses only the 10.76 and 3.75 micrometer spectral channels from VIIRS in two spectral tests; a straight-forward infrared threshold test with the longwave channel and a shortwave - longwave channel difference test. The key to the success of this approach as demonstrated in past applications to GOES and MODIS data is the generation of temporally and spatially dependent thresholds used in the tests from a previous number of days at similar observations to the current data. The paper and subsequent presentation will present an overview of the approach and intercomparison results with other satellites, methods, and against verification data.

Far Field Modeling Methods For Characterizing Surface Detonations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garrett, A.

2015-10-08

Savannah River National Laboratory (SRNL) analyzed particle samples collected during experiments that were designed to replicate tests of nuclear weapons components that involve detonation of high explosives (HE). SRNL collected the particle samples in the HE debris cloud using innovative rocket propelled samplers. SRNL used scanning electronic microscopy to determine the elemental constituents of the particles and their size distributions. Depleted uranium composed about 7% of the particle contents. SRNL used the particle size distributions and elemental composition to perform transport calculations that indicate in many terrains and atmospheric conditions the uranium bearing particles will be transported long distances downwind.more » This research established that HE tests specific to nuclear proliferation should be detectable at long downwind distances by sampling airborne particles created by the test detonations.« less

Motion data classification on the basis of dynamic time warping with a cloud point distance measure

NASA Astrophysics Data System (ADS)

Switonski, Adam; Josinski, Henryk; Zghidi, Hafedh; Wojciechowski, Konrad

2016-06-01

The paper deals with the problem of classification of model free motion data. The nearest neighbors classifier which is based on comparison performed by Dynamic Time Warping transform with cloud point distance measure is proposed. The classification utilizes both specific gait features reflected by a movements of subsequent skeleton joints and anthropometric data. To validate proposed approach human gait identification challenge problem is taken into consideration. The motion capture database containing data of 30 different humans collected in Human Motion Laboratory of Polish-Japanese Academy of Information Technology is used. The achieved results are satisfactory, the obtained accuracy of human recognition exceeds 90%. What is more, the applied cloud point distance measure does not depend on calibration process of motion capture system which results in reliable validation.

Uncertainty in aerosol hygroscopicity resulting from semi-volatile organic compounds

NASA Astrophysics Data System (ADS)

Goulden, Olivia; Crooks, Matthew; Connolly, Paul

2018-01-01

We present a novel method of exploring the effect of uncertainties in aerosol properties on cloud droplet number using existing cloud droplet activation parameterisations. Aerosol properties of a single involatile particle mode are randomly sampled within an uncertainty range and resulting maximum supersaturations and critical diameters calculated using the cloud droplet activation scheme. Hygroscopicity parameters are subsequently derived and the values of the mean and uncertainty are found to be comparable to experimental observations. A recently proposed cloud droplet activation scheme that includes the effects of co-condensation of semi-volatile organic compounds (SVOCs) onto a single lognormal mode of involatile particles is also considered. In addition to the uncertainties associated with the involatile particles, concentrations, volatility distributions and chemical composition of the SVOCs are randomly sampled and hygroscopicity parameters are derived using the cloud droplet activation scheme. The inclusion of SVOCs is found to have a significant effect on the hygroscopicity and contributes a large uncertainty. For non-volatile particles that are effective cloud condensation nuclei, the co-condensation of SVOCs reduces their actual hygroscopicity by approximately 25 %. A new concept of an effective hygroscopicity parameter is introduced that can computationally efficiently simulate the effect of SVOCs on cloud droplet number concentration without direct modelling of the organic compounds. These effective hygroscopicities can be as much as a factor of 2 higher than those of the non-volatile particles onto which the volatile organic compounds condense.

Using the C3M Satellite Data Product to Evaluate and Constrain the Cloud Fields in the HadGEM3-UKCA Model with an Aim to Enhance Understanding of the Effects of Clouds on Atmospheric Composition via Photolysis

NASA Astrophysics Data System (ADS)

Varma, S.; Voulgarakis, A.; Liu, H.; Crawford, J. H.; Zhang, B.

2017-12-01

What drives the variability of trace gases in the troposphere is not well understood, as is the role of clouds in modulating this variability via radiative, transport, deposition, heterogeneous chemistry, and lightning effects that are associated with them. Accurately simulating tropospheric composition and its variability is of utmost importance as both could have a significant effect on the region's temperature and circulation, as well as on surface climate and the amount of UV radiation in the troposphere. In this presentation, we will examine how clouds can influence tropospheric and lower stratospheric composition through modifying solar radiation leading to changes in the local actinic flux and subsequently to photolysis, a key driver of chemistry. We will utilize C3M (a unique 3-D cloud data product merged from multiple A-Train satellites (CERES, CloudSat, CALIPSO, and MODIS) developed at the NASA Langley Research Center to evaluate the cloud fields and their vertical distribution in the HadGEM3-UKCA model developed by the Natural Environment Research Council (NERC, UK) and the Met Office. This evaluation will involve 1) comparing the effective cloud optical depth (ECOD) as calculated from C3M and the model using the approximate random overlap method, 2) applying 3-D scaling factors from C3M to the model's ECOD and analyzing the changes this makes to the model's cloud fields, and 3) running the scaled model and analyzing the impacts of this cloud field adjustment on the model's estimates of photolysis rates and key tropospheric oxidants such as ozone and OH.

Prediction of optical communication link availability: real-time observation of cloud patterns using a ground-based thermal infrared camera

NASA Astrophysics Data System (ADS)

Bertin, Clément; Cros, Sylvain; Saint-Antonin, Laurent; Schmutz, Nicolas

2015-10-01

The growing demand for high-speed broadband communications with low orbital or geostationary satellites is a major challenge. Using an optical link at 1.55 μm is an advantageous solution which potentially can increase the satellite throughput by a factor 10. Nevertheless, cloud cover is an obstacle for this optical frequency. Such communication requires an innovative management system to optimize the optical link availability between a satellite and several Optical Ground Stations (OGS). The Saint-Exupery Technological Research Institute (France) leads the project ALBS (French acronym for BroadBand Satellite Access). This initiative involving small and medium enterprises, industrial groups and research institutions specialized in aeronautics and space industries, is currently developing various solutions to increase the telecommunication satellite bandwidth. This paper presents the development of a preliminary prediction system preventing the cloud blockage of an optical link between a satellite and a given OGS. An infrared thermal camera continuously observes (night and day) the sky vault. Cloud patterns are observed and classified several times a minute. The impact of the detected clouds on the optical beam (obstruction or not) is determined by the retrieval of the cloud optical depth at the wavelength of communication. This retrieval is based on realistic cloud-modelling on libRadtran. Then, using subsequent images, cloud speed and trajectory are estimated. Cloud blockage over an OGS can then be forecast up to 30 minutes ahead. With this information, the preparation of the new link between the satellite and another OGS under a clear sky can be prepared before the link breaks due to cloud blockage.

Cloud diagnosis impact on deposition modelling applied to the Fukushima accident

NASA Astrophysics Data System (ADS)

Quérel, Arnaud; Quélo, Denis; Roustan, Yelva; Mathieu, Anne

2017-04-01

The accident at the Fukushima Daiichi Nuclear Power Plant in Japan in March 2011 resulted in the release of several hundred PBq of activity into the environment. Most of the radioactivity was released in a time period of about 40 days. Radioactivity was dispersed in the atmosphere and the ocean and subsequently traces of radionuclides were detected all over Japan. At the Fukushima airport for instance, a deposit as large as 36 kBq/m2 of Cs-137 was measured resulting of an atmospheric deposition of the plume. Both dry and wet deposition were probably involved since a raining event occurred on the 15th of March when the plume was passing nearby. The accident scenario have given rise to a number of scientific investigations. Atmospheric deposition, for example, was studied by utilizing atmospheric transport models. In atmospheric transport models, some parameters, such as cloud diagnosis, are derived from meteorological data. This cloud diagnosis is a key issue for wet deposition modelling since it allows to distinguish between two processes: in-cloud scavenging which corresponds to the collection of radioactive particles into the cloud and below-cloud scavenging consequent to the removal of radioactive material due to the falling drops. Several parametrizations of cloud diagnosis exist in the literature, using different input data: relative humidity, liquid water content, also. All these diagnosis return a large range of cloud base heights and cloud top heights. In this study, computed cloud diagnostics are compared to the observations at the Fukushima airport. Atmospheric dispersion simulations at Japan scale are then performed utilizing the most reliable ones. Impact on results are discussed.

Small Negative Cloud-to-Ground Lightning Reports at the KSC-ER

NASA Technical Reports Server (NTRS)

Wilson, Jennifer G.; Cummins, Kenneth L.; Krider, E. Philip

2009-01-01

'1he NASA Kennedy Space Center (KSC) and Air Force Eastern Range (ER) use data from two cloud-to-ground (CG) lightning detection networks, the CGLSS and the NLDN, and a volumetric lightning mapping array, LDAR, to monitor and characterize lightning that is potentially hazardous to ground or launch operations. Data obtained from these systems during June-August 2006 have been examined to check the classification of small, negative CGLSS reports that have an estimated peak current, [I(sup p)] less than 7 kA, and to determine the smallest values of I(sup p), that are produced by first strokes, by subsequent strokes that create a new ground contact (NGC), and by subsequent strokes that remain in a pre-existing channel (PEC). The results show that within 20 km of the KSC-ER, 21% of the low-amplitude negative CGLSS reports were produced by first strokes, with a minimum I(sup p) of-2.9 kA; 31% were by NGCs, with a minimum I(sup p) of-2.0 kA; and 14% were by PECs, with a minimum I(sup p) of -2.2 kA. The remaining 34% were produced by cloud pulses or lightning events that we were not able to classify.

Ice nucleation active particles are efficiently removed by precipitating clouds.

PubMed

Stopelli, Emiliano; Conen, Franz; Morris, Cindy E; Herrmann, Erik; Bukowiecki, Nicolas; Alewell, Christine

2015-11-10

Ice nucleation in cold clouds is a decisive step in the formation of rain and snow. Observations and modelling suggest that variations in the concentrations of ice nucleating particles (INPs) affect timing, location and amount of precipitation. A quantitative description of the abundance and variability of INPs is crucial to assess and predict their influence on precipitation. Here we used the hydrological indicator δ(18)O to derive the fraction of water vapour lost from precipitating clouds and correlated it with the abundance of INPs in freshly fallen snow. Results show that the number of INPs active at temperatures ≥ -10 °C (INPs-10) halves for every 10% of vapour lost through precipitation. Particles of similar size (>0.5 μm) halve in number for only every 20% of vapour lost, suggesting effective microphysical processing of INPs during precipitation. We show that INPs active at moderate supercooling are rapidly depleted by precipitating clouds, limiting their impact on subsequent rainfall development in time and space.

Mixed-phase altocumulus clouds over Leipzig: Remote sensing measurements and spectral cloud microphysics simulations

NASA Astrophysics Data System (ADS)

Simmel, Martin; Bühl, Johannes; Ansmann, Albert; Tegen, Ina

2015-04-01

The present work combines remote sensing observations and detailed microphysics cloud modeling to investigate two altocumulus cloud cases observed over Leipzig, Germany. A suite of remote sensing instruments was able to detect primary ice at rather warm temperatures of -6°C. For comparison, a second mixed phase case at about -25°C is introduced. To further look into the details of cloud microphysical processes a simple dynamics model of the Asai-Kasahara type is combined with detailed spectral microphysics forming the model system AK-SPECS. Temperature and humidity profiles are taken either from observation (radiosonde) or GDAS reanalysis. Vertical velocities are prescribed to force the dynamics as well as main cloud features to be close to the observations. Subsequently, sensitivity studies with respect to dynamical as well as ice microphysical parameters are carried out with the aim to quantify the most important sensitivities for the cases investigated. For the cases selected, the liquid phase is mainly determined by the model dynamics (location and strength of vertical velocity) whereas the ice phase is much more sensitive to the microphysical parameters (ice nuclei (IN) number, ice particle shape). The choice of ice particle shape may induce large uncertainties which are in the same order as those for the temperature-dependent IN number distribution.

Cosesimic landslides and their post-quake effects (Invited)

NASA Astrophysics Data System (ADS)

Huang, R.; Fan, X.

2013-12-01

On May 12, 2008, a devastating earthquake of magnitude Mw 7.9 hit China's Sichuan province. The quake, originating in the Longmen Shan fault zone at the eastern margin of Tibetan Plateau, was the country's largest seismic event in more than 50 years. It triggered more than 60,000 destructive landslides and 828 landslide dams over an area of 35,000 square kilometers, that caused about one third of the total fatalities. The combination of strong and long-lasting ground shaking, steep, rugged topography and a fragile and densely jointed lithology probably controlled the occurrence of landslides during the earthquake, but we found that other two factors (fault type and slip rate during the earthquake), may also have played a role. Landslides were clustered in a much wider corridor along the thrusting part of the Yingxiu-Beichuan fault than the strike-slip part. Large-scale landslides with an area of more than 50,000 m2 were concentrated where fault slip-rates were highest, near the intersections and junctures of individual segments of the fault. After the earthquake, debris flow hazard has become a significant concern. A tremendous amount of loose material from landslides that occurred during the earthquake is suspended on the hillslopes, ready to be eroded and transported by rain. More than 2000 occurrences of debris flow have been recorded by the Land and Resources Department of Sichuan Province following the 2008 quake till 2012. The threshold in hourly rainfall intensity for triggering debris flows was found to be around 60% lower after the earthquake than it had been before, according to the record in Beichuan. How long it will take for the debris flow frequency to return to pre-earthquake levels depends on a large number of factors, including rainfall intensity, natural re-vegetation and self-stabilization processes on slopes. We anticipate that - despite large uncertainties - debris flows that directly result from sediment movement during the 2008 earthquake may remain active for another two decades. Presumably, their frequency will decline over time, which may draw out the effect even longer. Heightened landslide frequency after a quake, with potential secondary effects like river damming and subsequent floods, need more focused attention.

Flood of October 1986 at Seward, Alaska

USGS Publications Warehouse

Jones, S.H.; Zenone, Chester

1988-01-01

Broad areas along the lower Resurrection River and Salmon Creek as well as the surfaces of several adjacent alluvial fans in the Seward area were flooded as a result of the intensive rainstorm of October 9-11, 1986. Severe erosion took place through the steep gradient, mountain canyons and near the apex of the fans, while rock and debris were deposited on the distal parts of the fans. In Godwin, Lost, Box Canyon, Japanese, and Spruce Creek basins, and perhaps others, landslides or debris avalanches dammed the streams temporarily. Subsequent failure or overtopping of these dams led to ' surge-release ' flooding; peak discharge of such a flood at Spruce Creek was 13,600 cu ft/sec, four times as great as any previously known maximum discharge from the basin and 2.5 times as great as the runoff rate from the debris dam. Flood discharges were determined indirectly--using the slope-area method--at ten high-gradient reaches on nine streams. Computed peak discharges for several small basins were the largest since records began in 1963. The largest rainfall-runoff rate unaffected by surge-release was 1 ,020 cu ft per sec per sq mi at Rudolph Creek, which has a drainage area of 1.00 sq mi. The 15.05 inches of rain that fell in one 24-hour period during the storm was assigned a recurrence interval of 100 years or greater. The length of the streamflow record available for most Seward area streams-25 years or less-is inadequate to reliably define flood frequency relations for recurrence intervals as great as 100 years. However, the slope-area determined discharge of Spruce Creek above the debris avalanche indicates a recurrence interval of a 100 years or greater. In addition, conventional flood-frequency analysis techniques are not applicable to peak discharges that are affected by surge-release phenomena. Large, damaging floods have repeatedly caused major damage in the Seward area, and the potential for catastrophic, debris-laden floods is an ever-present threat to areas bordering the many steep mountain streams. (Author 's abstract)

Formation and mantling ages of lobate debris aprons on Mars: Insights from categorized crater counts

NASA Astrophysics Data System (ADS)

Berman, Daniel C.; Crown, David A.; Joseph, Emily C. S.

2015-06-01

Lobate debris aprons in the Martian mid-latitudes offer important insights into the history of the Martian climate and the role of volatiles in Martian geologic activity. Here we present the results of counts of small impact craters, categorized by morphology, on debris aprons in the Deuteronilus Mensae region and the area east of Hellas basin. Mars Reconnaissance Orbiter (MRO) ConTeXt Camera (CTX) images were used to document crater populations on the apron surfaces. Each crater was assessed and categorized according to its morphological characteristics (fresh, degraded, or filled). Fresh and most degraded craters likely superpose recent mantling deposits, whereas filled craters contain mantling deposits and thus indicate a minimum formation age for the apron (i.e., the age since stabilization of the debris apron surface following some modification but prior to mantling). Size-frequency distributions (SFDs) were compiled using established methodologies and plotted to assess their fit to the isochrons. The range or ranges in crater diameter over which each distribution paralleled the isochrons was determined by visual inspection, and general age constraints were noted from SFDs for all craters on a given surface and from each morphological class. The diameter range of each SFD segment observed to parallel an isochron was then input into the Craterstats2 analysis tool to calculate specific age estimates. The aprons were assessed both individually and as regional populations, which improved interpretation of the results and demonstrated the value and limitations of both approaches. The categorized counts reveal three groups of ages: (a) filled impact craters at larger diameters (>~500 m) typically show the oldest ages, between ~300 Ma and 1 Ga, (b) smaller diameter filled and degraded craters reveal ages of resurfacing events between ~10 Ma and 300 Ma, and (c) fresh crater populations (<~100 m diameter) indicate mantling deposits of less than ~10 Ma in age. These results indicate that the lobate debris apron populations formed (or their surfaces became stable) in the Early to Middle Amazonian Epochs, and were subsequently subjected to complex degradation by erosion and sublimation and/or melting of contained ice, culminating in episodes of deposition of ice-rich mantles in the Late Amazonian Epoch.

Seeding Experiment of Liquid Carbon Dioxide for Enhancing Winter-time Precipitation in Saga Prefecture,Northern Kyushu,Japan

NASA Astrophysics Data System (ADS)

Wakimizu, K.; Nishiyama, K.; Tomine, K.; Maki, T.; Suzuki, Y.; Morita, O.

2012-12-01

Many droughts (shortage of water) have broken out by extreme small amount rainfall in recent Japan. So far,in order to prevent these droughts,artificial rainfall methods with 'AgI' or 'dry ice' have been widely used in Japan. However,these methods have many problems,which a large amount of overcooling liquid in the cumulus cloud was not able to be converted into precipitation efficiently. So as to solve these problems,new artificial rainfall method using liquid carbon dioxide (LC) was proposed by Fukuta (1996). This new method consists of the generation of ice particles by homogeneous nucleation using LC and the subsequent more effective growth for ice particles without competition process. And, this method is called 'Low-Level Penetration Seeding of Homogeneous Ice Nucleant (LOLEPSHIN)' ; this induces a 'Roll-up Expansion of Twin Horizontal Ice-crystal Thermals (RETHIT)' and a subsequent 'Falling growth-Induced Lateral Air Spreading (FILAS)'. This LC method was applied to thin super-cooled cumulus clouds in Saga prefecture, Northern Kyushu, Japan on February 4,2006. The seeding airplane took off the Atugi Airport in Kanagawa Prefecture toward the Iki Island around 0830JST. Many cloud bands were cofirmed in the flight going to the experimental area and the cloud base temperature was approximately -9C (1200m). Scince some young developing thin cumuli were found over the Iki Island, LC seeding to these clouds was carried out two times from 0841JST until 0919JST penetrating the -9C (1200m) altitude. The first precipitation seeding ebded in failure. The second penetration seeding was done for 115 seconds around 0917JST. This penetration led to success of developing one artificial echo (Echo I) in the leeward side of the Iki Island. Eco I moved from NNW to SSW. The maximum area of Echo I were 48km2 (at 1033JST) and first comfirmed by the Kyushu University radar (KU radar) at 1006JST (46 min. after LC seeding) around Mt.Sefuri in Saga Prefecture. It can be inferred that ice perticles formed by LC seeding grew to the precipitable size and resultant snowfall was detected by radar in approximately 120 min. after seeding operation. In this study, based on these observed facts, optimum design for enhancing winter-time water resources by LC seeding method was suggested. Successive low-level horizontal penetrations of operational aircraft with seeding LC into many moving super-cooled cumuli towards the Japan Islands will lead to the spreading of cloud volume and subsequent coversion of large amount of iv active cloud volume into newly exploited artificial precipitation. As a result, these experiments succeeded, and the total amount of estimated radar precipitation of the be able to secure a large amount of water resource from these experiment results.

TerraSAR-X/TanDEM-X data for natural hazards research in mountainous regions of Uzbekistan

NASA Astrophysics Data System (ADS)

Semakova, Eleonora; Bühler, Yves

2017-07-01

Accurate and up-to-date digital elevation models (DEMs) are important tools for studying mountain hazards. We considered natural hazards related to glacier retreat, debris flows, and snow avalanches in two study areas of the Western Tien-Shan mountains, Uzbekistan. High-resolution DEMs were generated using single TerraSAR-X/TanDEM-X datasets. The high quality and actuality of the DEMs were proved through a comparison with Shuttle Radar Topography Mission, Advanced Spaceborne Emission and Reflection Radiometer, and Topo DEMs, using Ice, Cloud, and Land Elevation Satellite data as the reference dataset. For the first study area, which had high levels of economic activity, we applied the generated TanDEM-X DEM to an avalanche dynamics simulation using RAMMS software. Verification of the output results showed good agreement with field observations. For the second study area, with a wide spatial distribution of glaciers, we applied the TanDEM-X DEM to an assessment of glacier surface elevation changes. The results can be used to calculate the local mass balance in glacier ablation zones in other areas. Models were applied to estimate the probability of moraine-dammed lake formation and the affected area of a possible debris flow resulting from glacial lake outburst. The natural hazard research methods considered here will minimize costly ground observations in poorly accessible mountains and mitigate the impacts of hazards on the environment of Uzbekistan.

A Transient Transit Signature Associated with the Young Star RIK-210

DOE Office of Scientific and Technical Information (OSTI.GOV)

David, Trevor J.; Hillenbrand, Lynne A.; Howard, Andrew W.

We find transient transit-like dimming events within the K2 time series photometry of the young star RIK-210 in the Upper Scorpius OB association. These dimming events are variable in depth, duration, and morphology. High spatial resolution imaging revealed that the star is single and radial velocity monitoring indicated that the dimming events cannot be due to an eclipsing stellar or brown dwarf companion. Archival and follow-up photometry suggest the dimming events are transient in nature. The variable morphology of the dimming events suggests they are not due to a single spherical body. The ingress of each dimming event is alwaysmore » shallower than egress, as one would expect for an orbiting body with a leading tail. The dimming events are periodic and synchronous with the stellar rotation. However, we argue it is unlikely the dimming events could be attributed to anything on the stellar surface based on the observed depths and durations. Variable obscuration by a protoplanetary disk is unlikely on the basis that the star is not actively accreting and lacks the infrared excess associated with an inner disk. Rather, we explore the possibilities that the dimming events are due to magnetospheric clouds, a transiting protoplanet surrounded by circumplanetary dust and debris, eccentric orbiting bodies undergoing periodic tidal disruption, or an extended field of dust or debris near the corotation radius.« less

Measurement Comparisons Towards Improving the Understanding of Aerosol-Cloud Processing

NASA Astrophysics Data System (ADS)

Noble, Stephen R.

Cloud processing of aerosol is an aerosol-cloud interaction that is not heavily researched but could have implications on climate. The three types of cloud processing are chemical processing, collision and coalescence processing, and Brownian capture of interstitial particles. All types improve cloud condensation nuclei (CCN) in size or hygroscopicity (kappa). These improved CCN affect subsequent clouds. This dissertation focuses on measurement comparisons to improve our observations and understanding of aerosol-cloud processing. Particle size distributions measured at the continental Southern Great Plains (SGP) site were compared with ground based measurements of cloud fraction (CF) and cloud base altitude (CBA). Particle size distributions were described by a new objective shape parameter to define bimodality rather than an old subjective one. Cloudy conditions at SGP were found to be correlated with lagged shape parameter. Horizontal wind speed and regional CF explained 42%+ of this lag time. Many of these surface particle size distributions were influenced by aerosol-cloud processing. Thus, cloud processing may be more widespread with more implications than previously thought. Particle size distributions measured during two aircraft field campaigns (MArine Stratus/stratocumulus Experiment; MASE; and Ice in Cloud Experiment-Tropical; ICE-T) were compared to CCN distributions. Tuning particle size to critical supersaturation revealed hygroscopicity expressed as ? when the distributions were overlain. Distributions near cumulus clouds (ICE-T) had a higher frequency of the same ?s (48% in ICE-T to 42% in MASE) between the accumulation (processed) and Aitken (unprocessed) modes. This suggested physical processing domination in ICE-T. More MASE (stratus cloud) kappa differences between modes pointed to chemical cloud processing. Chemistry measurements made in MASE showed increases in sulfates and nitrates with distributions that were more processed. This supported chemical cloud processing in MASE. This new method to determine kappa provides the needed information without interrupting ambient measurements. MODIS derived cloud optical thickness (COT), cloud liquid water path (LWP), and cloud effective radius (re) were compared to the same in situ derived variables from cloud probe measurements of two stratus/stratocumulus cloud campaigns (MASE and Physics Of Stratocumulus Tops; POST). In situ data were from complete vertical cloud penetrations, while MODIS data were from pixels along the aircraft penetration path. Comparisons were well correlated except that MODIS LWP (14-36%) and re (20-30%) were biased high. The LWP bias was from re bias and was not improved by using the vertically stratified assumption. MODIS re bias was almost removed when compared to cloud top maximum in situ re, but, that does not describe re for the full depth of the cloud. COT is validated by in situ COT. High correlations suggest that MODIS variables are useful in self-comparisons such as gradient changes in stratus cloud re during aerosol-cloud processing.

Final Design for a Comprehensive Orbital Debris Management Program

NASA Technical Reports Server (NTRS)

1990-01-01

The rationale and specifics for the design of a comprehensive program for the control of orbital debris, as well as details of the various components of the overall plan, are described. The problem of orbital debris has been steadily worsening since the first successful launch in 1957. The hazards posed by orbital debris suggest the need for a progressive plan for the prevention of future debris, as well as the reduction of the current debris level. The proposed debris management plan includes debris removal systems and preventative techniques and policies. The debris removal is directed at improving the current debris environment. Because of the variance in sizes of debris, a single system cannot reasonably remove all kinds of debris. An active removal system, which deliberately retrieves targeted debris from known orbits, was determined to be effective in the disposal of debris tracked directly from earth. However, no effective system is currently available to remove the untrackable debris. The debris program is intended to protect the orbital environment from future abuses. This portion of the plan involves various environment from future abuses. This portion of the plan involves various methods and rules for future prevention of debris. The preventative techniques are protective methods that can be used in future design of payloads. The prevention policies are rules which should be employed to force the prevention of orbital debris.

Testing the Role of Impacts in Warming Early Mars: Comparisons Between 1-D and GCM Results

NASA Astrophysics Data System (ADS)

Steakley, K.; Kahre, M. A.; Murphy, J. R.; Haberle, R. M.; Kling, A.

2017-12-01

Comet and asteroid impacts have been explored as a potential mechanism for producing warmer and wetter conditions for early Mars and possibly contributing to valley network formation. However, criticisms have been made regarding the timing of large impacts compared to valley network activity and the ability of such impacts to induce long lasting climate changes and the appropriate amount of precipitation. We test the impact heating hypothesis for the late Noachian Mars atmosphere by revisiting the scenarios described in Segura et al. (2008, JGR Planets 113, E11007) with a 3D global climate model (GCM). Segura et al. (2008) showed with a 1-D model that impacts ranging 30-100 km in diameter could in certain cases induce months to years of above-freezing temperatures and tens of cm to meters of rainfall in atmospheres with 150-mbar, 1-bar, or 2-bar surface pressures. We impose the same initial conditions into the Ames Research Center Mars GCM with updated water cycle physics that includes bulk cloud formation, sedimentation, precipitation (liquid or snow), a Manabe moist convection scheme, and the radiative effects of both liquid and ice clouds. Initial conditions in the GCM match those described in Segura et al. (2008) as closely as possible and include a hot post-impact debris layer, a warm atmosphere, and water vapor profiles consistent with the water abundances mobilized by the impact. Scenarios with 30-, 50- and 100- km impactors in 150-mbar, 1-bar, and 2-bar surface pressure cases are explored both with and without radiatively active water clouds. Our goals are to determine how global rainfall totals and global surface temperatures from the GCM compare with the simpler 1-D Segura et al. (2008) model, to examine what rainfall patterns emerge in the GCM and how they compare to the observed valley network distribution, and to more carefully assess the role of cloud microphysics and radiative effects on the duration and intensity of post-impact climates.

Damage Assessment for Disaster Relief Efforts in Urban Areas Using Optical Imagery and LiDAR Data

NASA Astrophysics Data System (ADS)

Bahr, Thomas

2014-05-01

Imagery combined with LiDAR data and LiDAR-derived products provides a significant source of geospatial data which is of use in disaster mitigation planning. Feature rich building inventories can be constructed from tools with 3D rooftop extraction capabilities, and two dimensional outputs such as DSMs and DTMs can be used to generate layers to support routing efforts in Spatial Analyst and Network Analyst workflows. This allows us to leverage imagery and LiDAR tools for disaster mitigation or other scenarios. Software such as ENVI, ENVI LiDAR, and ArcGIS® Spatial and Network Analyst can therefore be used in conjunction to help emergency responders route ground teams in support of disaster relief efforts. This is exemplified by a case study against the background of the magnitude 7.0 earthquake that struck Haiti's capital city of Port-au-Prince on January 12, 2010. Soon after, both LiDAR data and an 8-band WorldView-2 scene were collected to map the disaster zone. The WorldView-2 scene was orthorectified and atmospherically corrected in ENVI prior to use. ENVI LiDAR was used to extract the DSM, DTM, buildings, and debris from the LiDAR data point cloud. These datasets provide a foundation for the 2D portion of the analysis. As the data was acquired over an area of dense urbanization, the majority of ground surfaces are roads, and standing buildings and debris are actually largely separable on the basis of elevation classes. To extract the road network of Port-au-Prince, the LiDAR-based feature height information was fused with the WorldView-2 scene, using ENVI's object-based feature extraction approach. This road network was converted to a network dataset for further analysis by the ArcGIS Network Analyst. For the specific case of Haiti, the distribution of blue tarps, used as accommodations for refugees, provided a spectrally distinct target. Pure blue tarp pixel spectra were selected from the WorldView-2 scene and input as a reference into ENVI's Spectral Angle Mapper (SAM) classification routine, together with a water-shadow mask to prevent false positives. The resulting blue tarp shape file was input into the ArcGIS Point Density tool, a feature of the Spatial Analyst toolbox. The final distribution map shows the density of blue tarps in Port-au-Prince and can be used to roughly delineate camps of refugees. Analogous, a debris density map was generated after separating the debris elevation class. The combination of this debris density map with the road network allowed to construct an intact road network of Port-au-Prince within the ArcGIS Network Analyst. Moderate density debris was used as a cost-increase barrier feature of the network dataset, and high density debris was used as a total obstruction barrier feature. Based on this information, two hypothetical routing scenarios were analyzed. One involved routing a ground team between two different refugee concentration zones. For the other, potential helicopter landing zones were computed from the LiDAR-derived products and added as facility features to the Network Analyst. Routes from the helicopter landing zones to refugee concentration access points were solved using closest facility logic, again making use of the obstructed network.

Global transport of atmospheric smoke following a major nuclear exchange

NASA Technical Reports Server (NTRS)

Haberle, R. M.; Ackerman, T. P.; Toon, O. B.; Hollingsworth, J. L.

1985-01-01

A fully interactive zonally symmetric general circulation model is used to simulate the transport and evolution of a massive smoke cloud that is likely to form in the atmosphere following a major nuclear war. The presence of such a cloud significantly alters the simulated circulation and the subsequent transport of the smoke particles themselves. While the model indicates a tendency for interhemispheric exchange, the most immediate effect is that the radiatively active particles are carried into the stratosphere by the generation of strong vertical motions and intense convection regardless of their initial injection altitudes.

Phase B - final definition and preliminary design study for the initial Atmospheric Cloud Physics Laboratory (ACPL): A spacelab mission payload. Work breakdown structure for phase C/D DR-MA-06 (preliminary issue)

NASA Technical Reports Server (NTRS)

1976-01-01

The Work Breakdown Structure (WBS) and Dictionary (DR-MA-06) for initial and subsequent flights of the Atmospheric Cloud Physics Laboratory (ACPL) is presented. An attempt is made to identify specific equipment and components in each of the eleven subsystems; they are listed under the appropriate subdivisions of the WBS. The reader is cautioned that some of these components are likely to change substantially during the course of the study, and the list provided should only be considered representative.

Global transport of atmospheric smoke following a major nuclear exchange

NASA Astrophysics Data System (ADS)

Haberle, Robert M.; Ackerman, Thomas P.; Toon, Owen B.; Hollingsworth, Jeffery L.

A fully interactive zonally symmetric general circulation model is used to simulate the transport and evolution of a massive smoke cloud that is likely to form in the atmosphere following a major nuclear war. The presence of such a cloud significantly alters the simulated circulation and the subsequent transport of the smoke particles themselves. While the model indicates a tendency for interhemispheric exchange, the most immediate effect is that the radiatively active particles are carried into the stratosphere by the generation of strong vertical motions and intense convection regardless of their initial injection altitudes.

Static Memory Deduplication for Performance Optimization in Cloud Computing.

PubMed

Jia, Gangyong; Han, Guangjie; Wang, Hao; Yang, Xuan

2017-04-27

In a cloud computing environment, the number of virtual machines (VMs) on a single physical server and the number of applications running on each VM are continuously growing. This has led to an enormous increase in the demand of memory capacity and subsequent increase in the energy consumption in the cloud. Lack of enough memory has become a major bottleneck for scalability and performance of virtualization interfaces in cloud computing. To address this problem, memory deduplication techniques which reduce memory demand through page sharing are being adopted. However, such techniques suffer from overheads in terms of number of online comparisons required for the memory deduplication. In this paper, we propose a static memory deduplication (SMD) technique which can reduce memory capacity requirement and provide performance optimization in cloud computing. The main innovation of SMD is that the process of page detection is performed offline, thus potentially reducing the performance cost, especially in terms of response time. In SMD, page comparisons are restricted to the code segment, which has the highest shared content. Our experimental results show that SMD efficiently reduces memory capacity requirement and improves performance. We demonstrate that, compared to other approaches, the cost in terms of the response time is negligible.

Ice phase in altocumulus clouds over Leipzig: remote sensing observations and detailed modeling

NASA Astrophysics Data System (ADS)

Simmel, M.; Bühl, J.; Ansmann, A.; Tegen, I.

2015-09-01

The present work combines remote sensing observations and detailed cloud modeling to investigate two altocumulus cloud cases observed over Leipzig, Germany. A suite of remote sensing instruments was able to detect primary ice at rather high temperatures of -6 °C. For comparison, a second mixed phase case at about -25 °C is introduced. To further look into the details of cloud microphysical processes, a simple dynamics model of the Asai-Kasahara (AK) type is combined with detailed spectral microphysics (SPECS) forming the model system AK-SPECS. Vertical velocities are prescribed to force the dynamics, as well as main cloud features, to be close to the observations. Subsequently, sensitivity studies with respect to ice microphysical parameters are carried out with the aim to quantify the most important sensitivities for the cases investigated. For the cases selected, the liquid phase is mainly determined by the model dynamics (location and strength of vertical velocity), whereas the ice phase is much more sensitive to the microphysical parameters (ice nucleating particle (INP) number, ice particle shape). The choice of ice particle shape may induce large uncertainties that are on the same order as those for the temperature-dependent INP number distribution.

Ice phase in altocumulus clouds over Leipzig: remote sensing observations and detailed modelling

NASA Astrophysics Data System (ADS)

Simmel, M.; Bühl, J.; Ansmann, A.; Tegen, I.

2015-01-01

The present work combines remote sensing observations and detailed cloud modeling to investigate two altocumulus cloud cases observed over Leipzig, Germany. A suite of remote sensing instruments was able to detect primary ice at rather warm temperatures of -6 °C. For comparison, a second mixed phase case at about -25 °C is introduced. To further look into the details of cloud microphysical processes a simple dynamics model of the Asai-Kasahara type is combined with detailed spectral microphysics forming the model system AK-SPECS. Vertical velocities are prescribed to force the dynamics as well as main cloud features to be close to the observations. Subsequently, sensitivity studies with respect to ice microphysical parameters are carried out with the aim to quantify the most important sensitivities for the cases investigated. For the cases selected, the liquid phase is mainly determined by the model dynamics (location and strength of vertical velocity) whereas the ice phase is much more sensitive to the microphysical parameters (ice nuclei (IN) number, ice particle shape). The choice of ice particle shape may induce large uncertainties which are in the same order as those for the temperature-dependent IN number distribution.

Static Memory Deduplication for Performance Optimization in Cloud Computing

PubMed Central

Jia, Gangyong; Han, Guangjie; Wang, Hao; Yang, Xuan

2017-01-01

In a cloud computing environment, the number of virtual machines (VMs) on a single physical server and the number of applications running on each VM are continuously growing. This has led to an enormous increase in the demand of memory capacity and subsequent increase in the energy consumption in the cloud. Lack of enough memory has become a major bottleneck for scalability and performance of virtualization interfaces in cloud computing. To address this problem, memory deduplication techniques which reduce memory demand through page sharing are being adopted. However, such techniques suffer from overheads in terms of number of online comparisons required for the memory deduplication. In this paper, we propose a static memory deduplication (SMD) technique which can reduce memory capacity requirement and provide performance optimization in cloud computing. The main innovation of SMD is that the process of page detection is performed offline, thus potentially reducing the performance cost, especially in terms of response time. In SMD, page comparisons are restricted to the code segment, which has the highest shared content. Our experimental results show that SMD efficiently reduces memory capacity requirement and improves performance. We demonstrate that, compared to other approaches, the cost in terms of the response time is negligible. PMID:28448434

Comparison of fast electric field changes from subsequent return strokes of natural and triggered lightning

NASA Technical Reports Server (NTRS)

Le Vine, D. M.; Willett, J.

1988-01-01

Fast electric field changes from subsequent return strokes of natural and triggered lightning with propagation paths almost entirely over water are compared. Data were collected at the Kennedy Space Center, Florida. Comparisons have been made of the average shape, the rise time and the spectrum of the electric field changes. The electric field changes from the triggered flashes tend to rise to peak faster and decay faster than do their counterparts in natural cloud-to-ground flashes.

The NASA Meter Class Autonomous Telescope: Ascension Island

NASA Technical Reports Server (NTRS)

Lederer, S. M.; Stansbery, E. G.; Cowardin, H. M.; Hickson, P.; Pace, L. F.; Abercromby, K. J.; Kervin, P. W.

2013-01-01

The Meter Class Autonomous Telescope (MCAT) is the newest optical sensor dedicated to NASA's mission to characterize the space debris environment. It is the successor to a series of optical telescopes developed and operated by the JSC Orbital Debris Program Office (ODPO) to monitor and assess the debris environment in (1) Low Earth Orbit (LEO), (2) Medium Earth Orbit (MEO), and (3) Geosynchronous Orbit (GEO), with emphasis on LEO and GEO altitudes. A joint NASA - Air Force Research Labs project, MCAT is a 1.3m optical telescope dedicated to debris research. Its optical path and sensor yield a large survey fence at the cutting edge of current detector performance. It has four primary operational observing modes, two of which were not computationally feasible a decade ago. Operations are supported by a sophisticated software suite that monitors clouds and weather conditions, and controls everything from data collection to dome rotation to processing tens of gigabytes of image data nightly. With fainter detection limits, precision detection, acquisition and tracking of targets, multi-color photometry, precision astrometry, automated re-acquisition capability, and the ability to process all data at the acquisition rate, MCAT is capable of producing and processing a volume and quality of data far in excess of any current (or prior) ODPO operations. This means higher fidelity population inputs and eliminating the multi-year backlog from acquisition-to-product typical of optical campaigns. All of this is possible given a suitable observing location. Ascension Island offers numerous advantages. As a British overseas territory with a US Air Force base presence, the necessary infrastructure and support already exists. It is located mid-way between Brazil and Africa at 7.93S latitude and 14.37 W longitude. With the Ground-based Electro-Optical Deep Space Surveillance (GEODSS) asset in Moron, Spain shutting down, this presents access to the sky from a unique latitude/longitude for an optical telescope. Constant trade winds from the SSE, originating from Africa, give promise to a steady laminar airflow over an island, a trait sought after to create stable atmospheric and good astronomical 'seeing' conditions with very low annual rainfall values. This combination of attributes created the necessary compelling argument to redirect MCAT to its final destination: Ascension Island.

Size-resolved Chemical Composition of Cloud and Rain Water Collected during the Puerto Rico African Dust and Clouds Study (PRADACS) Campaign

NASA Astrophysics Data System (ADS)

Torres, E.; Valle Diaz, C. J.; Zurcher, F.; Lee, T.; Collett, J. L.; Fitzgerald, E.; Cuadra, L.; Prather, K. A.; Mayol-Bracero, O. L.

2011-12-01

The underlying physico-chemical processes of dust-aerosol interactions are poorly understood; even less understood is how aging impacts cloud properties and climate as the particles travel from Africa to the Caribbean region. Caribbean landmasses have tropical montane cloud forests (TMCFs) that are tightly coupled to the atmospheric hydrologic cycle. Small-scale shifts in temperature and precipitation could have serious ecological consequences. Therefore, this makes TMCFs an interesting ecosystem to see the effects African Dust (AD) might have on cloud formation and precipitation. As part of the Puerto Rico African Dust and Clouds Study (PRADACS) cloud and rain water samples for subsequent chemical analysis were collected at Pico del Este (PE) station in Luquillo, PR (1051 masl) during summer 2011. At PE, two cloud collectors (i.e., single stage (Aluminum version) and 2-stage (Teflon version) Caltech Active Strand Cloudwater Collector (CASCC)), and a rainwater collector were operated. Measurements such as the liquid water content (LWC), pH, conductivity., and composition of single particles using an aerosol time of flight mass spectrometer (ATOFMS) were performed. Preliminary results showed that days with the influence of African dust (AD), had LWC values that ranged from 300 to 500 mg/m3, pH values up to 5.7,, and conductivity up to 180 μS/cm. The ATOFMS showed titanium and iron ions, suggesting the presence of AD as well as, occasionally, sulfate and nitrate ions suggesting the influence of anthropogenic pollution. Results on the chemical composition and the physical properties of cloud, rainwater, and aerosol for the inorganic as well as the organic fraction and how these properties change for the different air masses observed will also be presented.

Volcanic Hazards Associated with the NE Sector of Tacaná Volcano, Guatemala.

NASA Astrophysics Data System (ADS)

Hughes, S. R.; Saucedo, R.; Macias, J.; Arce, J.; Garcia-Palomo, A.; Mora, J.; Scolamacchia, T.

2003-12-01

Tacaná volcano, with a height of 4,030 m above sea level, straddles the southern Mexico/Guatemala border. Last active in 1986, when there was a small phreatic event with a duration of a few days, this volcano presents an impending hazard to over 250,000 people. The NE sector of the volcano reveals the violent volcanic history of Tacaná that may be indicative of a serious potential risk to the area. Its earliest pyroclastic history appears to consist of fall, flow, and surge deposits, together with lavas, that have formed megablocks within a series of old debris avalanche deposits. This sector collapse event is overlain by a sequence of pumice fall and ash flow deposits, of which the youngest, less-altered pumice fall deposit shows a minimum thickness of > 4 m, with a dispersal axis trending toward the NE. A second debris avalanche deposit, separated from the above deposits by a paleosoil, is dominated by megablocks of lava and scoriaceous dome material. The current topography around the northeastern flank of the volcano is determined by a third, and most recent debris avalanche deposit, a thick (> 20 m) sequence of six block and ash flows dated at around 16,000 years BP, each separated by 1-10 cm thick ash cloud surge deposit, together with secondary lahar deposits. These are followed by a at least 4 lava flows that extend 2 km down the flank of the volcano. It appears that the most recent pyroclastic event at Tacaná is also recorded in this sector of the volcano: above the block and ash flows occurs a > 1 m thick ash flow unit that can be seen at least 5 km from the vent. Lastly, the Santa Maria Ash fall deposit, produced in 1902, has capped most of the deposits at Tacaná.

Glacier changes in the Ravi basin, North-Western Himalaya (India) during the last four decades (1971-2010/13)

NASA Astrophysics Data System (ADS)

Chand, Pritam; Sharma, Milap Chand

2015-12-01

A glacier inventory of the Ravi basin, north-western Himalaya has been generated for the year 2002 using Landsat ETM + and ASTER Global DEM (GDEM V2) as the baseline data for the change analysis. The Ravi basin consists of 285 glaciers (> 0.02 km2) covering an area of 164.5 ± 7.5 km2, including 71 debris-covered glaciers with an area of 36.1 ± 2.1 km2 (22% of total glacierized area) in 2002. Change analysis based on Corona KH-4B (1971), Worldview (2010) and Landsat 8 OLI/TRIS (2013) images was restricted to a subset of 157 glaciers (covering an area of 121.4 ± 5.4 km2 in 2002) due to cloud cover. Glacier area decreased from 125.8 ± 1.9 km2 (1971) to 119.9 ± 4.8 km2 (2010/13), a loss of 4.7 ± 4.1% or 0.1 ± 0.1% a- 1. The glacier recession rate has decreased, to a minimum for the recent decades (2002-2010/13). The debris-covered glacier area increased by 19.2 ± 2.2% (0.5 ± 0.05% a- 1) in the Ravi basin. However, there were significant variation in its sub-basins i.e. in Budhil and Upper Ravi sub-basin, where the debris-covered area increased by 28.6 ± 3.1% (0.7 ± 0.1% a- 1) and 14 ± 1.6% (0.3 ± 0.04% a- 1), respectively, between 1971 and 2010/13. Field investigation of selected glaciers (2010-2014) supports glacier recession trend from remote sensing data. Glacier retreat rates in the Ravi basin were lower than previously reported for selected glaciers in the similar basin and other basins (e.g. Chenab, Beas, Parbati, Baspa and Tirungkhad) of the Himachal Himalaya.

Hardware in the Loop Performance Assessment of LIDAR-Based Spacecraft Pose Determination

PubMed Central

Fasano, Giancarmine; Grassi, Michele

2017-01-01

In this paper an original, easy to reproduce, semi-analytic calibration approach is developed for hardware-in-the-loop performance assessment of pose determination algorithms processing point cloud data, collected by imaging a non-cooperative target with LIDARs. The laboratory setup includes a scanning LIDAR, a monocular camera, a scaled-replica of a satellite-like target, and a set of calibration tools. The point clouds are processed by uncooperative model-based algorithms to estimate the target relative position and attitude with respect to the LIDAR. Target images, acquired by a monocular camera operated simultaneously with the LIDAR, are processed applying standard solutions to the Perspective-n-Points problem to get high-accuracy pose estimates which can be used as a benchmark to evaluate the accuracy attained by the LIDAR-based techniques. To this aim, a precise knowledge of the extrinsic relative calibration between the camera and the LIDAR is essential, and it is obtained by implementing an original calibration approach which does not need ad-hoc homologous targets (e.g., retro-reflectors) easily recognizable by the two sensors. The pose determination techniques investigated by this work are of interest to space applications involving close-proximity maneuvers between non-cooperative platforms, e.g., on-orbit servicing and active debris removal. PMID:28946651