Effects of Molybdenum and Vanadium Addition on Tensile and Charpy Impact Properties of API X70 Linepipe Steels

NASA Astrophysics Data System (ADS)

Kim, Young Min; Shin, Sang Yong; Lee, Hakcheol; Hwang, Byoungchul; Lee, Sunghak; Kim, Nack J.

2007-08-01

This study is concerned with the effects of V and Mo addition on tensile and Charpy impact properties of API X70 linepipe steels. Twelve kinds of steel specimens were produced by varying V and Mo additions and rolling conditions. The addition of V and Mo promoted the formation of acicular ferrite (AF), banitic ferrite (BF), and martensite-austenite (MA) constituents, while suppressing the formation of polygonal ferrite (PF) or pearlite (P). The tensile test results indicated that the tensile strength of the specimens rolled in the two-phase region increased with the addition of V and Mo, while the yield strength did not vary much in these specimens except the water-cooled specimens, which showed the increased yield strength with addition of Mo. The tensile strength of specimens rolled in the single-phase region followed by water cooling increased with increasing V and Mo contents. The yield strength, however, did not vary much with increasing V content or with addition of Mo to the low-V alloy. In these specimens, a substantial increase in the strengths was achieved only when Mo was added to the high-V alloy. The specimens rolled in the single-phase region had higher upper-shelf energy (USE) and lower ductile-brittle transition temperature (DBTT) than the specimens rolled in the two-phase region, because their microstructures were composed of AF and fine PF. According to the electron backscatter diffraction (EBSD) analysis data, the effective grain size in AF was determined by crystallographic packets composed of a few fine grains having similar orientations. Thus, the decreased DBTT in the specimens rolled in the single-phase region could be explained by the decrease in the overall effective grain size due to the presence of AF having smaller effective grain size.

Relative susceptibility of titanium alloys to hot-salt stress-corrosion

NASA Technical Reports Server (NTRS)

Gray, H. R.

1971-01-01

Susceptibility of titanium alloys to hot-salt stress-corrosion cracking increased as follows: Ti-2Al-11Sn-5Zr-0.2Si(679), Ti-6Al-2Sn-4Zr-2Mo(6242), Ti-6Al-4V(64), Ti-6Al-4V-3Co(643), Ti-8Al-1Mo-1V(811), and Ti-13V-11Cr-3A1(13-11-3). The Ti-5Al-6Sn-2Zr-1Mo-0.25Si(5621S) alloy was both the least and most susceptible depending on heat treatment. Such rankings can be drastically altered by heat-to-heat and processing variations. Residual compressive stresses and cyclic exposures also reduce susceptibility to stress-corrosion. Simulated turbine-engine compressor environmental variables such as air velocity, pressure, dewpoint, salt concentration, and salt deposition temperature have only minor effects. Detection of substantial concentrations of hydrogen in all corroded alloys confirmed the existence of a hydrogen embrittlement mechanism.

First-principles calculations on strain and electric field induced band modulation and phase transition of bilayer WSe2sbnd MoS2 heterostructure

NASA Astrophysics Data System (ADS)

Lei, Xiang; Yu, Ke

2018-04-01

A purposeful modulation of physical properties of material via change external conditions has long captured people's interest and can provide many opportunities to improve the specific performance of electronic devices. In this work, a comprehensive first-principles survey was performed to elucidate that the bandgap and electronic properties of WSe2sbnd MoS2 heterostructure exhibited unusual response to exterior strain and electric field in comparison with pristine structures. It demonstrates that the WSe2sbnd MoS2 is a typical type-II heterostructure, and thus the electron-hole pairs can be effectively spatially separated. The external effects can trigger the electronic phase transition from semiconducting to metallic state, which originates from the internal electric evolution induced energy-level shift. Interestingly, the applied strain shows no direction-depended character for the modulation of bandgap of WSe2sbnd MoS2 heterostructure, while it exists in the electric field tuning processes and strongly depends on the direction of the electric field. Our findings elucidate the tunable electronic property of bilayer WSe2sbnd MoS2 heterostructure, and would provide a valuable reference to design the electronic nanodevices.

Hydrothermal growth of two dimensional hierarchical MoS2 nanospheres on one dimensional CdS nanorods for high performance and stable visible photocatalytic H2 evolution

NASA Astrophysics Data System (ADS)

Chava, Rama Krishna; Do, Jeong Yeon; Kang, Misook

2018-03-01

The visible photocatalytic H2 production from water splitting considered as a clean and renewable energy source could solve the problem of greenhouse gas emission from fossil fuels. Despite tremendous efforts, the development of cost effective, highly efficient and more stable visible photocatalysts for splitting of water remains a great challenge. Here, we report the heteronanostructures consisting of hierarchical MoS2 nanospheres grown on 1D CdS nanorods referred to as CdS-MoS2 HNSs as a high performance visible photocatalyst for H2 evolution. The as-synthesized CdS-MoS2 HNSs exhibited ∼11 fold increment of H2 evolution rate when compared to pure CdS nanorods. This remarkable enhanced hydrogen evolution performance can be assigned to the positive synergetic effect from heteronanostructures formed between the CdS and MoS2 components which assist as an electron sink and source for abundant active edge sites and in turn increases the charge separation. This study presents a low-cost visible photocatalyst for solar energy conversion to achieve efficient H2.

76 FR 31920 - Endangered and Threatened Wildlife and Plants; 90-Day Finding on a Petition To List the Golden...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-02

...-0028; MO 92210-0-0008] Endangered and Threatened Wildlife and Plants; 90-Day Finding on a Petition To... our review, we find that the petition presents substantial scientific or commercial information... scientific and commercial data and other information regarding this species. Based on the status review, we...

75 FR 13068 - Endangered and Threatened Wildlife and Plants; 90-Day Finding on a Petition to List the Berry...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-18

...-0011] [MO 92210-0-0008-B2] Endangered and Threatened Wildlife and Plants; 90-Day Finding on a Petition... that the petition presents substantial scientific or commercial information indicating that listing... ensure that this status review is comprehensive, we are requesting scientific and commercial data and...

75 FR 8601 - Endangered and Threatened Wildlife and Plants; 12-Month Finding on a Petition To List the Sonoran...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-25

...-0059; MO 92210-0-0008] Endangered and Threatened Wildlife and Plants; 12-Month Finding on a Petition To... all available scientific and commercial information, we find that the Sonoran Desert Area population... the Lists of Endangered and Threatened Wildlife and Plants that contains substantial scientific or...

76 FR 40868 - Endangered and Threatened Wildlife and Plants; 90-Day Finding on a Petition To List the Bay...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-12

...-0012; MO 92210-0-0008] Endangered and Threatened Wildlife and Plants; 90-Day Finding on a Petition To... habitat. Based on our review, we find that the petition presents substantial scientific or commercial... warranted. To ensure that this status review is comprehensive, we are requesting scientific and commercial...

76 FR 62740 - Endangered and Threatened Wildlife and Plants; 12-Month Finding on a Petition and Proposed Rule...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-11

...-0075; MO 92210-0-0010 B6] Endangered and Threatened Wildlife and Plants; 12-Month Finding on a Petition... the Federal Lists of Endangered and Threatened Wildlife and Plants that contains substantial scientific or commercial information that listing the species may be warranted, we make a finding within 12...

Fish Intake and the Risk of Incident Heart Failure: The Women’s Health Initiative

PubMed Central

Belin, Rashad J.; Greenland, Philip; Martin, Lisa; Oberman, Albert; Tinker, Lesley; Robinson, Jennifer; Larson, Joseph; Horn, Linda Van; Lloyd-Jones, Donald

2012-01-01

Background Whether fish or the fatty acids they contain are independently associated with risk for incident heart failure (HF) among postmenopausal women is unclear. Methods and Results The baseline Women’s Health Initiative Observational Study (WHI-OS) cohort consisted of 93,676 women aged 50–79 of diverse ethnicity and background of which 84,493 were eligible for analyses. Intakes of baked/broiled fish, fried fish and omega-3 fatty acid (eicosapentaenoic acid (EPA) + docosahexaenoic acid (DHA), α-linolenic acid (ALA)), and trans fatty acid (TFA) were determined from the WHI food frequency questionnaire. Baked/broiled fish consumption was divided into 5 frequency categories: <1/mo (referent), 1–3/mo, 1–2/wk, 3–4/wk, ≥5/wk. Fried fish intake was grouped into 3 frequency categories: <1/mo (referent), 2) 1–3/mo, and 3) ≥1/wk. Associations between fish or fatty acid intake and incident HF were determined using Cox models adjusting for HF risk factors and dietary factors. Baked/broiled fish consumption (≥5 servings/wk at baseline) was associated with a hazard ratio (HR) of 0.70 (95% CI: 0.51, 0.95) for incident HF. In contrast, fried fish consumption (≥1 serving/wk at baseline) was associated with a HR of 1.48 (95% CI: 1.19, 1.84) for incident HF. No significant associations were found between EPA+DHA, ALA, or TFA intake and incident HF. Conclusions Increased baked/broiled fish intake may lower HF risk, while increased fried fish intake may increase HF risk in postmenopausal women. PMID:21610249

Cobalt internal standard for Ni to assist the simultaneous determination of Mo and Ni in plant materials by high-resolution continuum source graphite furnace atomic absorption spectrometry employing direct solid sample analysis.

PubMed

de Babos, Diego Victor; Bechlin, Marcos André; Barros, Ariane Isis; Ferreira, Edilene Cristina; Gomes Neto, José Anchieta; de Oliveira, Silvana Ruella

2016-05-15

A new method is proposed for the simultaneous determination of Mo and Ni in plant materials by high-resolution continuum source graphite furnace atomic absorption spectrometry (HR-CS GFAAS), employing direct solid sample analysis (DSS) and internal standardization (IS). Cobalt was used as internal standard to minimize matrix effects during Ni determinations, enabling the use of aqueous standards for calibration. Correlation coefficients for the calibration curves were typically better than 0.9937. The performance of the method was checked by analysis of six plant certified reference materials, and the results for Mo and Ni were in agreement with the certified values (95% confidence level, t-test). Analysis was made of different types of plant materials used as renewable sources of energy, including sugarcane leaves, banana tree fiber, soybean straw, coffee pods, orange bagasse, peanut hulls, and sugarcane bagasse. The concentrations found for Mo and Ni ranged from 0.08 to 0.63 ng mg(-1) and from 0.41 to 6.92 ng mg(-1), respectively. Precision (RSD) varied from 2.1% to 11% for Mo and from 3.7% to 10% for Ni. Limits of quantification of 0.055 and 0.074 ng were obtained for Mo and Ni, respectively. Copyright © 2016 Elsevier B.V. All rights reserved.

Origins of the structural phase transitions in MoTe2 and WTe2

NASA Astrophysics Data System (ADS)

Kim, Hyun-Jung; Kang, Seoung-Hun; Hamada, Ikutaro; Son, Young-Woo

2017-05-01

Layered transition metal dichalcogenides MoTe2 and WTe2 share almost similar lattice constants as well as topological electronic properties except their structural phase transitions. While the former shows a first-order phase transition between monoclinic and orthorhombic structures, the latter does not. Using a recently proposed van der Waals density functional method, we investigate structural stability of the two materials and uncover that the disparate phase transitions originate from delicate differences between their interlayer bonding states near the Fermi energy. By exploiting the relation between the structural phase transitions and the low energy electronic properties, we show that a charge doping can control the transition substantially, thereby suggesting a way to stabilize or to eliminate their topological electronic energy bands.

The south Karelia air pollution study: Effects of low-level expsoure to malodorous sulfur compounds on symptoms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Partti-Pellinen, K.; Marttila, O.; Vilkka, V.

1996-07-01

Exposure to very low levels of ambient-air malodorous sulfur compounds and their effect on eye irritation, respiratory-tract symptoms, and central nervous system symptoms in adults were assessed. A cross-sectional self-administered questionnaire (response rate = 77%) was distributed during March and April 1992 to adults (n = 336) who lived in a neighborhood that contained a pulp mill and in a nonpolluted reference community (n = 380). In the exposed community, the measured annual mean concentrations of total reduced sulfur compounds and sulfur dioxide measured in two stations were 2 to 3 {mu}g/m{sup 3} and 1 {mu}g/m{sup 3}, respectively. In themore » reference community, the annual mean concentration of sulfur dioxide was 1 {mu}g/m{sup 3}. The residents of the community near the pulp mill reported an excess of cough, respiratory infections, and headache during the previous 4 wk, as well as during the preceding 12 mo. The relative risk for headache was increased significantly in the exposed community, compared with the reference area: the adjusted odds ratio (aOR) was 1.83 (95% confidence interval [95% Cl] = 1.06-3.15) during the previous 4 wk and 1.70 (95% Cl = 1.05-2.73) during the preceding 12 mo. The relative risk for cough was also increased during the preceding 12 mo (aOR = 1.64, 95% Cl = 1.01-2.64). These results indicated that adverse health effects of malodorous sulfur compounds occur at lower concentrations than reported previously. 25 refs., 3 tabs.« less

KCl-Induced High-Temperature Corrosion Behavior of HVAF-Sprayed Ni-Based Coatings in Ambient Air

NASA Astrophysics Data System (ADS)

Jafari, Reza; Sadeghimeresht, Esmaeil; Farahani, Taghi Shahrabi; Huhtakangas, Matti; Markocsan, Nicolaie; Joshi, Shrikant

2018-02-01

KCl-induced high-temperature corrosion behavior of four HVAF-sprayed Ni-based coatings (Ni21Cr, Ni5Al, Ni21Cr7Al1Y and Ni21Cr9Mo) under KCl deposit has been investigated in ambient air at 600 °C up to 168 h. The coatings were deposited onto 16Mo3 steel—a widely used boiler tube material. Uncoated substrate, 304L and Sanicro 25 were used as reference materials in the test environment. SEM/EDS and XRD techniques were utilized to characterize the as-sprayed and exposed samples. The results showed that the small addition of KCl significantly accelerated degradation to the coatings. All coatings provided better corrosion resistance compared to the reference materials. The alumina-forming Ni5Al coating under KCl deposit was capable of forming a more protective oxide scale compared to the chromia-forming coatings as penetration of Cl through diffusion paths was hindered. Both active corrosion and chromate formation mechanisms were found to be responsible for the corrosion damages. The corrosion resistance of the coatings based on the microstructure analysis and kinetics had the following ranking (from the best to worst): Ni5Al > Ni21Cr > Ni21Cr7Al1Y > Ni21Cr9Mo.

Reduced molybenum-oxide-based core-shell hybrids: "blue" electrons are delocalized on the shell.

PubMed

Todea, Ana Maria; Szakács, Julia; Konar, Sanjit; Bögge, Hartmut; Crans, Debbie C; Glaser, Thorsten; Rousselière, Hélène; Thouvenot, René; Gouzerh, Pierre; Müller, Achim

2011-06-06

The present study refers to a variety of reduced metal-oxide core-shell hybrids, which are unique with regard to their electronic structure, their geometry, and their formation. They contain spherical {Mo72Fe30} Keplerate-type shells encapsulating Keggin-type polyoxomolybdates based on very weak interactions. Studies on the encapsulation of molybdosilicate as well as on the earlier reported molybdophosphate, coupled with the use of several physical methods for the characterization led to unprecedented results (see title). Upon standing in air at room temperature, acidified aqueous solutions obtained by dissolving sodium molybdate, iron(II) chloride, acetic acid, and molybdosilicic acid led to the precipitation of monoclinic greenish crystals (1). A rhombohedral variant (2) has also been observed. Upon drying at room temperature, compound 3 with a layer structure was obtained from 1 in a solid-state reaction based on cross-linking of the shells. The compounds 1, 2, and 3 have been characterized by a combination of methods including single-crystal X-ray crystallography, magnetic studies, as well as IR, Mössbauer, (resonance) Raman, and electronic absorption spectroscopy. In connection with detailed studies of the guest-free two-electron-reduced {Mo72Fe30}-type Keplerate (4) and of the previously reported molybdophosphate-based hybrids (including 31P NMR spectroscopy results), it is unambiguously proved that 1, 2, and 3 contain non-reduced Keggin ion cores and reduced {Mo72Fe30}-type shells. The results are discussed in terms of redox considerations (the shell as well as the core can be reduced) including those related to the reduction of "molybdates" by FeII being of interdisciplinary including catalytic interest (the MoVI/MoV and FeIII/FeII couples have very close redox potentials!), while also referring to the special formation of the hybrids based on chemical Darwinism.

Sputter-deposited WO x and MoO x for hole selective contacts

DOE PAGES

Bivour, Martin; Zähringer, Florian; Ndione, Paul F.; ...

2017-09-21

Here, reactive sputter deposited tungsten and molybdenum oxide (WO x, MoO x) thin films are tested for their ability to form a hole selective contact for Si wafer based solar cells. A characterization approach based on analyzing the band bending induced in the c-Si absorber and the external and implied open-circuit voltage of test structures was used. It is shown that the oxygen partial pressure allows to tailor the selectivity to some extent and that a direct correlation between induced band bending and hole selectivity exists. Although the selectivity of the sputtered films is inferior to the reference films depositedmore » by thermal evaporation, these results demonstrate a good starting point for further optimizations of sputtered WO x and MoO x towards higher work functions to improve the hole selectivity.« less

Sputter-deposited WO x and MoO x for hole selective contacts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bivour, Martin; Zähringer, Florian; Ndione, Paul F.

Here, reactive sputter deposited tungsten and molybdenum oxide (WO x, MoO x) thin films are tested for their ability to form a hole selective contact for Si wafer based solar cells. A characterization approach based on analyzing the band bending induced in the c-Si absorber and the external and implied open-circuit voltage of test structures was used. It is shown that the oxygen partial pressure allows to tailor the selectivity to some extent and that a direct correlation between induced band bending and hole selectivity exists. Although the selectivity of the sputtered films is inferior to the reference films depositedmore » by thermal evaporation, these results demonstrate a good starting point for further optimizations of sputtered WO x and MoO x towards higher work functions to improve the hole selectivity.« less

Irradiation performance of U-Mo monolithic fuel

DOE PAGES

Meyer, M. K.; Gan, J.; Jue, J. F.; ...

2014-04-01

High-performance research reactors require fuel that operates at high specific power to high fission density, but at relatively low temperatures. Research reactor fuels are designed for efficient heat rejection, and are composed of assemblies of thin-plates clad in aluminum alloy. The development of low-enriched fuels to replace high-enriched fuels for these reactors requires a substantially increased uranium density in the fuel to offset the decrease in enrichment. Very few fuel phases have been identified that have the required combination of very-high uranium density and stable fuel behavior at high burnup. U-Mo alloys represent the best known tradeoff in these properties.more » Testing of aluminum matrix U-Mo aluminum matrix dispersion fuel revealed a pattern of breakaway swelling behavior at intermediate burnup, related to the formation of a molybdenum stabilized high aluminum intermetallic phase that forms during irradiation. In the case of monolithic fuel, this issue was addressed by eliminating, as much as possible, the interfacial area between U-Mo and aluminum. Based on scoping irradiation test data, a fuel plate system composed of solid U-10Mo fuel meat, a zirconium diffusion barrier, and Al6061 cladding was selected for development. Developmental testing of this fuel system indicates that it meets core criteria for fuel qualification, including stable and predictable swelling behavior, mechanical integrity to high burnup, and geometric stability. In addition, the fuel exhibits robust behavior during power-cooling mismatch events under irradiation at high power.« less

The role of electronic coupling between substrate and 2D MoS2 nanosheets in electrocatalytic production of hydrogen.

PubMed

Voiry, Damien; Fullon, Raymond; Yang, Jieun; de Carvalho Castro E Silva, Cecilia; Kappera, Rajesh; Bozkurt, Ibrahim; Kaplan, Daniel; Lagos, Maureen J; Batson, Philip E; Gupta, Gautam; Mohite, Aditya D; Dong, Liang; Er, Dequan; Shenoy, Vivek B; Asefa, Tewodros; Chhowalla, Manish

2016-09-01

The excellent catalytic activity of metallic MoS2 edges for the hydrogen evolution reaction (HER) has led to substantial efforts towards increasing the edge concentration. The 2H basal plane is less active for the HER because it is less conducting and therefore possesses less efficient charge transfer kinetics. Here we show that the activity of the 2H basal planes of monolayer MoS2 nanosheets can be made comparable to state-of-the-art catalytic properties of metallic edges and the 1T phase by improving the electrical coupling between the substrate and the catalyst so that electron injection from the electrode and transport to the catalyst active site is facilitated. Phase-engineered low-resistance contacts on monolayer 2H-phase MoS2 basal plane lead to higher efficiency of charge injection in the nanosheets so that its intrinsic activity towards the HER can be measured. We demonstrate that onset potentials and Tafel slopes of ∼-0.1 V and ∼50 mV per decade can be achieved from 2H-phase catalysts where only the basal plane is exposed. We show that efficient charge injection and the presence of naturally occurring sulfur vacancies are responsible for the observed increase in catalytic activity of the 2H basal plane. Our results provide new insights into the role of contact resistance and charge transport on the performance of two-dimensional MoS2 nanosheet catalysts for the HER.

Solution processed transition metal oxide anode buffer layers for efficiency and stability enhancement of polymer solar cells

NASA Astrophysics Data System (ADS)

Ameen, M. Yoosuf; Shamjid, P.; Abhijith, T.; Reddy, V. S.

2018-01-01

Polymer solar cells were fabricated with solution-processed transition metal oxides, MoO3 and V2O5 as anode buffer layers (ABLs). The optimized device with V2O5 ABL exhibited considerably higher power conversion efficiency (PCE) compared to the devices based on MoO3 and poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) ABLs. The space charge limited current measurements and impedance spectroscopy results of hole-only devices revealed that V2O5 provided a very low charge transfer resistance and high hole mobility, facilitating efficient hole transfer from the active layer to the ITO anode. More importantly, incorporation of V2O5 as ABL resulted in substantial improvement in device stability compared to MoO3 and PEDOT:PSS based devices. Unencapsulated PEDOT:PSS-based devices stored at a relative humidity of 45% have shown complete failure within 96 h. Whereas, MoO3 and V2O5 based devices stored in similar conditions retained 22% and 80% of their initial PCEs after 96 h. Significantly higher stability of the V2O5-based device is ascribed to the reduction in degradation of the anode/active layer interface, as evident from the electrical measurements.

Role of Phragmites australis (common reed) for heavy metals phytoremediation of estuarine sediments.

PubMed

Cicero-Fernández, Diego; Peña-Fernández, Manuel; Expósito-Camargo, Jose A; Antizar-Ladislao, Blanca

2016-01-01

The ability of Phragmites australis to take up heavy metals (Co, Ni, Mo, Cd, Pb, Cr, Cu, Fe, Mn, Zn, and Hg) and other trace elements (As, Se, Ba), from estuarine sediments was investigated using a pilot plant experimental approach. Bioaccumulation (BCF) and translocation factors (TF) were calculated in vegetative and senescence periods for two populations of P. australis, from contaminated (MIC) and non-contaminated (GAL) estuarine sediments, respectively, both growing in estuarine contaminated sediment (RIA) from ría del Carmen y Boo, Santander Bay, Spain. The highest BCF values were obtained for Ni (0.43), Ba (0.43) Mo (0.36), Cr (0.35), and Cd (0.31) for plants collected from site GAL following the senescence period. The highest BCF values recorded for plants collected from MIC following the senescence period were for Mo (0.22) and Cu (0.22). Following senescence, plants collected from GAL and MIC presented TF>1 for Ni, Mo, Se, and Zn, and in addition plants collected from MIC presented TF>1 for Ba, Cr, and Mn. A substantial increase of Micedo's rhizosphere, six times higher than Galizano's rhizosphere, suggested adaptation to contaminated sediment. The evaluated communities of P. australis demonstrated their suitability for phytoremediation of heavy metals contaminated estuarine sediments.

Study of urological devices coated with fullerene-like nanoparticles.

PubMed

Goldbart, Ohad; Elianov, Olga; Shumalinsky, Dmitry; Lobik, Leonid; Cytron, Shmuel; Rosentsveig, Rita; Wagner, H Daniel; Tenne, Reshef

2013-09-21

Insertion of endoscopes and other medical devices into the human body are ubiquitous, especially among aged males. The applied force for the insertion/extraction of the device from the urethra must overcome endoscope-surface-human-tissue interactions. In daily practice a gel is applied on the endoscope surface, in order to facilitate its entry into the urethra, providing also for local anesthesia. In the present work, a new solid-state lubricant has been added to the gel, in order to reduce the metal-urethra interaction and alleviate the potential damage to the epithelial tissue. For that purpose, a urethra model was designed and fabricated, which allowed a quantitative assessment of the applied force for extraction of the endoscope from a soft polymer-based ring. It is shown that the addition of MoS2 nanoparticles with fullerene-like structure (IF-MoS2) and in particular rhenium-doped nanoparticles (Re:IF-MoS2) to Esracain gel applied on the metal-lead reduced the friction substantially. The Re:IF-MoS2 showed better results than the undoped fullerene-like nanoparticles and both performed better than the gel alone. The mechanism of friction reduction is attributed to fullerenes' ability to roll and act as a separator between the active parts of the model.

Study of urological devices coated with fullerene-like nanoparticles

NASA Astrophysics Data System (ADS)

Goldbart, Ohad; Elianov, Olga; Shumalinsky, Dmitry; Lobik, Leonid; Cytron, Shmuel; Rosentsveig, Rita; Wagner, H. Daniel; Tenne, Reshef

2013-08-01

Insertion of endoscopes and other medical devices into the human body are ubiquitous, especially among aged males. The applied force for the insertion/extraction of the device from the urethra must overcome endoscope-surface-human-tissue interactions. In daily practice a gel is applied on the endoscope surface, in order to facilitate its entry into the urethra, providing also for local anesthesia. In the present work, a new solid-state lubricant has been added to the gel, in order to reduce the metal-urethra interaction and alleviate the potential damage to the epithelial tissue. For that purpose, a urethra model was designed and fabricated, which allowed a quantitative assessment of the applied force for extraction of the endoscope from a soft polymer-based ring. It is shown that the addition of MoS2 nanoparticles with fullerene-like structure (IF-MoS2) and in particular rhenium-doped nanoparticles (Re:IF-MoS2) to Esracain gel applied on the metal-lead reduced the friction substantially. The Re:IF-MoS2 showed better results than the undoped fullerene-like nanoparticles and both performed better than the gel alone. The mechanism of friction reduction is attributed to fullerenes' ability to roll and act as a separator between the active parts of the model.

Laser Direct Writing Process for Making Electrodes and High-k Sol-Gel ZrO2 for Boosting Performances of MoS2 Transistors.

PubMed

Kwon, Hyuk-Jun; Jang, Jaewon; Grigoropoulos, Costas P

2016-04-13

A series of two-dimensional (2D) transition metal dichalcogenides (TMDCs), including molybdenum disulfide (MoS2), can be attractive materials for photonic and electronic applications due to their exceptional properties. Among these unique properties, high mobility of 2D TMDCs enables realization of high-performance nanoelectronics based on a thin film transistor (TFT) platform. In this contribution, we report highly enhanced field effect mobility (μ(eff) = 50.1 cm(2)/(V s), ∼2.5 times) of MoS2 TFTs through the sol-gel processed high-k ZrO2 (∼22.0) insulator, compared to those of typical MoS2/SiO2/Si structures (μ(eff) = 19.4 cm(2)/(V s)) because a high-k dielectric layer can suppress Coulomb electron scattering and reduce interface trap concentration. Additionally, in order to avoid costly conventional mask based photolithography and define the patterns, we employ a simple laser direct writing (LDW) process. This process allows precise and flexible control with reasonable resolution (up to ∼10 nm), depending on the system, and enables fabrication of arbitrarily patterned devices. Taking advantage of continuing developments in laser technology offers a substantial cost decrease, and LDW may emerge as a promising technology.

A highly oxidized atmosphere-ocean system and oceanic molybdenum drawdown during the Paleoproterozoic

NASA Astrophysics Data System (ADS)

Goto, K. T.; Ito, T.; Suzuki, K.; Anbar, A. D.; Gordon, G. W.; Kashiwabara, T.; Takaya, Y.; Shimoda, G.; Nozaki, T.; Kiyokawa, S.; Tetteh, G. M.; Nyame, F. K.

2014-12-01

Multiple lines of evidence suggest that the first major oxidation of the atmosphere-ocean system occurred during the Paleoproterozoic. However, the course of this redox transition remains elusive. A number of large Mn deposits are distributed in Paleoproterozoic sedimentary successions. As Mn is a redox-sensitive element characterized by high redox potential, knowledge of the Mn cycle in Paleoproterozoic seawater may provide insight into redox evolution during this period. Here, we investigate the Mn cycle in Paleoproterozoic seawater based on the Re-Os and Mo isotope compositions, and the abundance of major and trace elements, in Mn-rich sedimentary rocks from the Nsuta deposit of the Birimian Supergroup, Ghana. The Mn ore is composed mainly of rhodochrosite and is distributed at the boundaries between sedimentary rocks and tholeiitic volcanic rocks. The Re-Os isochron age (2217 ± 100 Ma) we obtained was consistent with U-Pb zircon ages of the volcanic rocks. The manganophile elements, except for Mo, show no enrichment, which is similar to modern hydrothermal Mn oxides. The PAAS-normalized REE compositions show positive Ce anomaly, indicative of Ce enrichment due to the oxidation of Ce(III) by Mn(IV). These findings suggest that Mn ore formed from primary precipitation of Mn oxides from hydrothermal fluids as they were mixed with bottom seawater at ~2.2 Ga. Thus, the bottom seawater would have been sufficiently oxygenated for the precipitation of Mn oxides at ~2.2 Ga. The Nsuta ore samples exhibit slight Mo enrichment, but Mo/Mn ratios are orders of magnitude lower than those in modern hydrothermal Mn oxides. We also found that the Mo isotopes in the Nsuta ore are ~0.7‰ heavier than those in modern hydrothermal and hydrogenous Mn oxides. As Mo in hydrothermal Mn oxides is sourced primarily from seawater (Goto et al., in prep), these results may reflect smaller oceanic Mo inventory and heavier seawater Mo isotope composition at 2.2 Ga than those of present-day. Our calculation using a simple mass balance model suggests that substantial removal of light Mo by Mn oxides may have caused such oceanic conditions. Our findings are consistent with the recently proposed 'oxygen overshoot' model (Bekker and Holland, 2012) and low Mo contents in ~2.2-Ga black shales and sedimentary pyrites (e.g., Scott et al., 2008).

76 FR 32911 - Endangered and Threatened Wildlife and Plants; 12-Month Finding on a Petition To List the Striped...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-07

... Endangered Wildlife and Plants that contains substantial scientific or commercial information that listing a...-0007; MO 92210-0-0008 B2] Endangered and Threatened Wildlife and Plants; 12-Month Finding on a Petition... Endangered Species Act of 1973, as amended (Act). After review of all available scientific and commercial...

75 FR 13720 - Endangered and Threatened Wildlife and Plants; 90-Day Finding on a Petition to List the Striped...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-23

... areas of pond where light penetrates and rooted plants occur) of breeding sites have been destroyed by...-0007] [MO 92210-0-0008-B2] Endangered and Threatened Wildlife and Plants; 90-Day Finding on a Petition... substantial scientific or commercial information indicating that listing the striped newt may be warranted...

Metal complexes of fluorophosphines. 13. Reaction of fac-(CH/sub 3/CN)/sub 3/Mo(CO)/sub 3/ with (methylamino)bis(difluorophosphine). X-ray crystal structure analysis of a novel binuclear molybdenum fluorophosphine carbonyl complex with a bridging chlorine atom: (CO)/sub 2/Mo(/sup +/-CH/sub 3/N(PF/sub 2/)/sub 2/)/sub 2/(. mu. -PF/sub 2/)(. mu. -Cl)Mo(CO)(PF/sub 2/NHCH/sub 3/)

DOE Office of Scientific and Technical Information (OSTI.GOV)

King, R.B.; Shimura, M.; Brown, G.M.

1984-01-01

Reaction of fac-(CH/sub 3/CN)/sub 3/Mo(CO)/sub 3/ with CH/sub 3/N(PF/sub 2/)/sub 2/ in acetonitrile solution at room temperature gives white, volatile, crystalline fac-(CH/sub 3/N(PF/sub 2/)/sub 2/)/sub 2/Mo(CO)/sub 3/, containing one monodentate and one bidentate CH/sub 3/N(PF/sub 2/)/sub 2/ ligand. The same reactants in boiling acetonitrile give yellow (CH/sub 3/N(PF/sub 2/)/sub 2/)/sub 4/Mo/sub 2/(CO)/sub 3/ in considerably better yield than the previously reported preparation of this binuclear complex from the cycloheptatriene complex C/sub 7/H/sub 8/Mo(CO)/sub 3/ and CH/sub 3/N(PF/sub 2/)/sub 2/ in boiling methylcyclohexane. Reaction in acetonitrile solution of fac-(CH/sub 3/CN)/sub 3/Mo(CO)/sub 3/ with CH/sub 3/N(PF/sub 2/)/sub 2/ containing about 0.2% HClmore » gives brown-red, volatile (CO)/sub 2/Mo(/sup +/-CH/sub 3/N(PF/sub 2/)/sub 2/)/sub 2/(..mu..-PF/sub 2/)(..mu..-Cl)-Mo(CO)(PF/sub 2/NHCH/sub 3/), whose composition and structure were established by single-crystal X-ray structure analysis. This novel quadruply bridged binuclear complex is obtained in considerably better yield from the reaction of (CH/sub 3/N(PF/sub 2/)/sub 2/)/sub 3/Mo/sub 2/(CO)/sub 5/ with ((C/sub 2/H/sub 5/)/sub 3/NH)Cl in acetonitirle solution. The complex has a Mo-Mo bond 2.975 A in length. Crystal data: monoclinic, space group P2/sub 1//c, a = 17.546 (4) A, b = 9.725 (2) A, c = 14.558 (3), ..beta.. = 107.20 (2)/sup 0/, Z = 4. 30 references, 2 figures, 3 tables.« less

Measurement Error, Reliability, and Minimum Detectable Change in the Mini-Mental State Examination, Montreal Cognitive Assessment, and Color Trails Test among Community Living Middle-Aged and Older Adults.

PubMed

Feeney, Joanne; Savva, George M; O'Regan, Claire; King-Kallimanis, Bellinda; Cronin, Hilary; Kenny, Rose Anne

2016-05-31

Knowing the reliability of cognitive tests, particularly those commonly used in clinical practice, is important in order to interpret the clinical significance of a change in performance or a low score on a single test. To report the intra-class correlation (ICC), standard error of measurement (SEM) and minimum detectable change (MDC) for the Mini-Mental State Examination (MMSE), Montreal Cognitive Assessment (MoCA), and Color Trails Test (CTT) among community dwelling older adults. 130 participants aged 55 and older without severe cognitive impairment underwent two cognitive assessments between two and four months apart. Half the group changed rater between assessments and half changed time of day. Mean (standard deviation) MMSE was 28.1 (2.1) at baseline and 28.4 (2.1) at repeat. Mean (SD) MoCA increased from 24.8 (3.6) to 25.2 (3.6). There was a rater effect on CTT, but not on the MMSE or MoCA. The SEM of the MMSE was 1.0, leading to an MDC (based on a 95% confidence interval) of 3 points. The SEM of the MoCA was 1.5, implying an MDC95 of 4 points. MoCA (ICC = 0.81) was more reliable than MMSE (ICC = 0.75), but all tests examined showed substantial within-patient variation. An individual's score would have to change by greater than or equal to 3 points on the MMSE and 4 points on the MoCA for the rater to be confident that the change was not due to measurement error. This has important implications for epidemiologists and clinicians in dementia screening and diagnosis.

Rhenium Alloys as Ductile Substrates for Diamond Thin-Film Electrodes.

PubMed

Halpern, Jeffrey M; Martin, Heidi B

2014-02-01

Molybdenum-rhenium (Mo/Re) and tungsten-rhenium (W/Re) alloys were investigated as substrates for thin-film, polycrystalline boron-doped diamond electrodes. Traditional, carbide-forming metal substrates adhere strongly to diamond but lose their ductility during exposure to the high-temperature (1000°C) diamond, chemical vapor deposition environment. Boron-doped semi-metallic diamond was selectively deposited for up to 20 hours on one end of Mo/Re (47.5/52.5 wt.%) and W/Re (75/25 wt.%) alloy wires. Conformal diamond films on the alloys displayed grain sizes and Raman signatures similar to films grown on tungsten; in all cases, the morphology and Raman spectra were consistent with well-faceted, microcrystalline diamond with minimal sp 2 carbon content. Cyclic voltammograms of dopamine in phosphate-buffered saline (PBS) showed the wide window and low baseline current of high-quality diamond electrodes. In addition, the films showed consistently well-defined, dopamine electrochemical redox activity. The Mo/Re substrate regions that were uncoated but still exposed to the diamond-growth environment remained substantially more flexible than tungsten in a bend-to-fracture rotation test, bending to the test maximum of 90° and not fracturing. The W/Re substrates fractured after a 27° bend, and the tungsten fractured after a 21° bend. Brittle, transgranular cleavage fracture surfaces were observed for tungsten and W/Re. A tension-induced fracture of the Mo/Re after the prior bend test showed a dimple fracture with a visible ductile core. Overall, the Mo/Re and W/Re alloys were suitable substrates for diamond growth. The Mo/Re alloy remained significantly more ductile than traditional tungsten substrates after diamond growth, and thus may be an attractive metal substrate for more ductile, thin-film diamond electrodes.

Rhenium Alloys as Ductile Substrates for Diamond Thin-Film Electrodes

PubMed Central

Halpern, Jeffrey M.; Martin, Heidi B.

2014-01-01

Molybdenum-rhenium (Mo/Re) and tungsten-rhenium (W/Re) alloys were investigated as substrates for thin-film, polycrystalline boron-doped diamond electrodes. Traditional, carbide-forming metal substrates adhere strongly to diamond but lose their ductility during exposure to the high-temperature (1000°C) diamond, chemical vapor deposition environment. Boron-doped semi-metallic diamond was selectively deposited for up to 20 hours on one end of Mo/Re (47.5/52.5 wt.%) and W/Re (75/25 wt.%) alloy wires. Conformal diamond films on the alloys displayed grain sizes and Raman signatures similar to films grown on tungsten; in all cases, the morphology and Raman spectra were consistent with well-faceted, microcrystalline diamond with minimal sp2 carbon content. Cyclic voltammograms of dopamine in phosphate-buffered saline (PBS) showed the wide window and low baseline current of high-quality diamond electrodes. In addition, the films showed consistently well-defined, dopamine electrochemical redox activity. The Mo/Re substrate regions that were uncoated but still exposed to the diamond-growth environment remained substantially more flexible than tungsten in a bend-to-fracture rotation test, bending to the test maximum of 90° and not fracturing. The W/Re substrates fractured after a 27° bend, and the tungsten fractured after a 21° bend. Brittle, transgranular cleavage fracture surfaces were observed for tungsten and W/Re. A tension-induced fracture of the Mo/Re after the prior bend test showed a dimple fracture with a visible ductile core. Overall, the Mo/Re and W/Re alloys were suitable substrates for diamond growth. The Mo/Re alloy remained significantly more ductile than traditional tungsten substrates after diamond growth, and thus may be an attractive metal substrate for more ductile, thin-film diamond electrodes. PMID:25404788

Physiotherapy Maneuver Is Critical to Recover Mouth Opening After Pediatric Trauma.

PubMed

Khalifa, Ghada Amin; El-Kilani, Naglaa Shawki; Shokier, Hanan Mohamed

2016-12-01

A restricted mouth opening (MO) is predominantly a complication of maxillofacial trauma in pediatric patients and develops in 4 to 26.2% of cases. The purpose of the present study was to quantitatively investigate the influence of patient demographic data, fracture characteristics, and regular vigorous physiotherapy, with either voluntary or forcible MO exercises, on the recovery of a post-traumatic restricted MO in pediatric patients. A prospective cohort study was performed of pediatric patients with maxillofacial injuries who had been referred to Al-Zahraa and El-Fayoum Hospitals from 2013 to 2015. The predictive variables were patient demographic data, fracture characteristics, and regular vigorous physiotherapy. The patients were treated with a closed technique. The MO measurements were the clinical outcome variables and were recorded at the first week and then monthly for 12 months. Regular vigorous physiotherapy was performed until the patients had returned to their preoperative MO. The data were tabulated and statistically analyzed. Eighty-six patients were enrolled in the present study. Males predominated. Falls were the most common cause of fracture. Condylar fractures had the greatest incidence. A restricted MO occurred in 81 patients. The results showed no interaction between MO recovery and age, gender, etiology, or fracture site. After physiotherapy, the patients had returned to their preoperative MO at the fourth month, with the measurements fixed at normal values at the sixth month. The recovery rate was nonlinear, with faster improvement in the months closest to the injury. Physiotherapy is more critical in the recovery of the MO and prevention of bony ankylosis than patient data or fracture characteristics in pediatric trauma. We highly advocate the performance of voluntary mouth exercises, even in the absence of fracture. Forcible MO exercises are mandatory to recover a restricted MO. These exercises should be performed under close supervision of the patient's surgeon with the parents motivated to cooperate for at least 6 months. Copyright © 2016 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

Interface Engineering of Monolayer MoS2/GaN Hybrid Heterostructure: Modified Band Alignment for Photocatalytic Water Splitting Application by Nitridation Treatment.

PubMed

Zhang, Zhaofu; Qian, Qingkai; Li, Baikui; Chen, Kevin J

2018-05-23

Interface engineering is a key strategy to deal with the two-dimensional (2D)/three-dimensional (3D) hybrid heterostructure, since the properties of this atomic-layer-thick 2D material can easily be impacted by the substrate environment. In this work, the structural, electronic, and optical properties of the 2D/3D heterostructure of monolayer MoS 2 on wurtzite GaN surface without and with nitridation interfacial layer are systematically investigated by first-principles calculation and experimental analysis. The nitridation interfacial layer can be introduced into the 2D/3D heterostructure by remote N 2 plasma treatment to GaN sample surface prior to stacking monolayer MoS 2 on top. The calculation results reveal that the 2D/3D integrated heterostructure is energetically favorable with a negative formation energy. Both interfaces demonstrate indirect band gap, which is a benefit for longer lifetime of the photoexcited carriers. Meanwhile, the conduction band edge and valence band edge of the MoS 2 side increases after nitridation treatment. The modification to band alignment is then verified by X-ray photoelectron spectroscopy measurement on MoS 2 /GaN heterostructures constructed by a modified wet-transfer technique, which indicates that the MoS 2 /GaN heterostructure without nitridation shows a type-II alignment with a conduction band offset (CBO) of only 0.07 eV. However, by the deployment of interface nitridation, the band edges of MoS 2 move upward for ∼0.5 eV as a result of the nitridized substrate property. The significantly increased CBO could lead to better electron accumulation capability at the GaN side. The nitridized 2D/3D heterostructure with effective interface treatment exhibits a clean band gap and substantial optical absorption ability and could be potentially used as practical photocatalyst for hydrogen generation by water splitting using solar energy.

Traditional oral remedies and perceived breast milk insufficiency are major barriers to exclusive breastfeeding in rural Zimbabwe.

PubMed

Desai, Amy; Mbuya, Mduduzi N N; Chigumira, Ancikaria; Chasekwa, Bernard; Humphrey, Jean H; Moulton, Lawrence H; Pelto, Gretel; Gerema, Grace; Stoltzfus, Rebecca J

2014-07-01

Only 5.8% of Zimbabwean infants are exclusively breastfed for the first 6 mo of life despite substantial investment in exclusive breastfeeding (EBF) promotion throughout the country. We conducted a survey of 295 mothers of infants <6 mo of age who were recruited from rural immunization clinics and outreach sites in the Midlands Province of Zimbabwe. We explored infant feeding knowledge, beliefs and attitudes, and details regarding facilitators for EBF mothers and first foods fed by non-EBF mothers to identify and understand barriers to EBF. Among mothers of infants <1 mo, 1 to <2 mo, and 2-6 mo of age, 54%, 30%, and 12%, respectively, were practicing EBF. In adjusted multivariate analyses, EBF practice was positively associated with belief in the sufficiency of EBF (P = 0.05), belief in the avoidance of cooking oil feeding (a common traditional practice) in the first 6 mo (P = 0.001), and perceived pressure from others regarding infant feeding and traditional medicine use (P = 0.03). Psychosocial support and viewing breast milk as sufficient were reported as primary facilitators of EBF practice. Maternal responses to open-ended questions identified protection, nutrition, and crying as the main reasons for EBF interruption. During the first 2 mo of life, "protection feedings" using traditional oral remedies (such as cooking oil and water) to prevent or treat perceived illness, specifically colic and sunken/depressed fontanel, made up 78.5% of the non-breast milk feeds. From the second month of life, "nutrition feedings," mainly of water and porridge, were given when mothers believed their breast milk was insufficient in quantity or quality to meet the hunger or thirst needs of their infants. Our findings underscore the importance of exploring cultural beliefs and practices as they pertain to infant feeding and care and present insights for designing and targeting EBF promotion interventions. © 2014 American Society for Nutrition.

Corrosion Characteristics of Ni-Based Hardfacing Alloy Deposited on Stainless Steel Substrate by Laser Cladding

NASA Astrophysics Data System (ADS)

Awasthi, Reena; Abraham, Geogy; Kumar, Santosh; Bhattacharyya, Kaustava; Keskar, Nachiket; Kushwaha, R. P.; Rao, Ramana; Tewari, R.; Srivastava, D.; Dey, G. K.

2017-06-01

In this study, corrosion characteristics of a nickel-based Ni-Mo-Cr-Si hardfacing alloy having 32Mo, 15Cr, and 3Si (wt pct) as alloying elements, deposited on stainless steel SS316L substrate by laser cladding, have been presented. Corrosion behavior of the laser clad layer was evaluated in reducing (0.1 M HCl) and oxidizing (0.5 M HNO3) environments, in comparison with the reference substrate SS316L, using electrochemical potentiodynamic technique at room temperature. The corrosion mechanisms have been evaluated on the basis of microstructural and microchemical analysis using scanning electron microscopy attached with energy-dispersive spectrometry. Passivity behavior of the laser clad layer was studied in 0.5 M H2SO4, using the potentiostatic technique and analyzing the passive layer by X-ray photoelectron spectroscopy. Laser clad layer of Ni-Mo-Cr-Si exhibited higher pitting corrosion resistance in chloride (reducing) environment, indicated by much higher breakdown potential ( 0.8 VSCE) and the absence of pitting as compared to substrate SS316L ( 0.3 VSCE). However, in oxidizing (0.5 M HNO3) environment, both the laser clad layer and substrate SS316L showed excellent and similar corrosion resistance exhibiting high breakdown potential ( 0.85 VSCE) and wide passivation range ( 0.8 VSCE) with low passive current density ( 4 to 7 × 10-6 A/cm2). The stable passive layer formed on laser clad layer of Ni-Mo-Cr-Si after exposure in 0.5 M H2SO4 solution at constant potential 0.6 VSCE (within the passive range), consisted oxides of Mo as Mo+4 (MoO2) and Mo+6 (MoO4)-2, Cr as Cr3+ (mixture of both Cr2O3 and Cr (OH)3), and Si as Si4+(SiO2), which have contributed to passivation and repassivation and therefore excellent corrosion behavior.

MANUAL: GROUND-WATER AND LEACHATE TREATMENT SYSTEMS

EPA Science Inventory

This manual was developed for remedial design engineers and regulatory personnel who oversee the ex situ ground water or leachate treatment efforts of the regulated community. The manual can be used as a treatment technology screening tool in conjunction with other references. Mo...

Price discounts significantly enhance fruit and vegetable purchases when combined with nutrition education: a randomized controlled supermarket trial.

PubMed

Waterlander, Wilma E; de Boer, Michiel R; Schuit, Albertine J; Seidell, Jacob C; Steenhuis, Ingrid H M

2013-04-01

Reducing fruit and vegetable (F&V) prices is a frequently considered policy to improve dietary habits in the context of health promotion. However, evidence on the effectiveness of this intervention is limited. The objective was to examine the effects of a 50% price discount on F&Vs or nutrition education or a combination of both on supermarket purchases. A 6-mo randomized controlled trial within Dutch supermarkets was conducted. Regular supermarket shoppers were randomly assigned to 1 of 4 conditions: 50% price discounts on F&Vs, nutrition education, 50% price discounts plus nutrition education, or no intervention. A total of 199 participants provided baseline data; 151 (76%) were included in the final analysis. F&V purchases were measured by using supermarket register receipts at baseline, at 1 mo after the start of the intervention, at 3 mo, at 6 mo (end of the intervention period), and 3 mo after the intervention ended (9 mo). Adjusted multilevel models showed significantly higher F&V purchases (per household/2 wk) as a result of the price discount (+3.9 kg; 95% CI: 1.5, 6.3 kg) and the discount plus education intervention (+5.6 kg; 95% CI: 3.2, 7.9 kg) at 6 mo compared with control. Moreover, the percentage of participants who consumed recommended amounts of F&Vs (≥400 g/d) increased from 42.5% at baseline to 61.3% at 6 mo in both discount groups (P = 0.03). Education alone had no significant effect. Discounting F&Vs is a promising intervention strategy because it resulted in substantially higher F&V purchases, and no adverse effects were observed. Therefore, pricing strategies form an important focus for future interventions or policy. However, the long-term effects and the ultimate health outcomes require further investigation. This trial was registered at the ISRCTN Trial Register as number ISRCTN56596945 and at the Dutch Trial Register (http://www.trialregister.nl/trialreg/index.asp) as number NL22568.029.08.

Effects of stress ratio on the temperature-dependent high-cycle fatigue properties of alloy steels

NASA Astrophysics Data System (ADS)

Lü, Zhi-yang; Wan, Ao-shuang; Xiong, Jun-jiang; Li, Kuang; Liu, Jian-zhong

2016-12-01

This paper addresses the effects of stress ratio on the temperature-dependent high-cycle fatigue (HCF) properties of alloy steels 2CrMo and 9CrCo, which suffer from substantial vibrational loading at small stress amplitude, high stress ratio, and high frequency in the high-temperature environments in which they function as blade and rotor spindle materials in advanced gas or steam turbine engines. Fatigue tests were performed on alloy steels 2CrMo and 9CrCo subjected to constant-amplitude loading at four stress ratios and at four and three temperatures, respectively, to determine their temperature-dependent HCF properties. The interaction mechanisms between high temperature and stress ratio were deduced and compared with each other on the basis of the results of fractographic analysis. A phenomenological model was developed to evaluate the effects of stress ratio on the temperature-dependent HCF properties of alloy steels 2CrMo and 9CrCo. Good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed method.

Surface Characterization, Corrosion Resistance and in Vitro Biocompatibility of a New Ti-Hf-Mo-Sn Alloy

PubMed Central

Ion, Raluca; Drob, Silviu Iulian; Ijaz, Muhammad Farzik; Vasilescu, Cora; Osiceanu, Petre; Gordin, Doina-Margareta; Cimpean, Anisoara; Gloriant, Thierry

2016-01-01

A new superelastic Ti-23Hf-3Mo-4Sn biomedical alloy displaying a particularly large recovery strain was synthesized and characterized in this study. Its native passive film is very thick (18 nm) and contains very protective TiO2, Ti2O3, HfO2, MoO2, and SnO2 oxides (XPS analysis). This alloy revealed nobler electrochemical behavior, more favorable values of the corrosion parameters and open circuit potentials in simulated body fluid in comparison with commercially pure titanium (CP-Ti) and Ti-6Al-4V alloy taken as reference biomaterials in this study. This is due to the favorable influence of the alloying elements Hf, Sn, Mo, which enhance the protective properties of the native passive film on alloy surface. Impedance spectra showed a passive film with two layers, an inner, capacitive, barrier, dense layer and an outer, less insulating, porous layer that confer both high corrosion resistance and bioactivity to the alloy. In vitro tests were carried out in order to evaluate the response of Human Umbilical Vein Endothelial Cells (HUVECs) to Ti-23Hf-3Mo-4Sn alloy in terms of cell viability, cell proliferation, phenotypic marker expression and nitric oxide release. The results indicate a similar level of cytocompatibility with HUVEC cells cultured on Ti-23Hf-3Mo-4Sn substrate and those cultured on the conventional CP-Ti and Ti-6Al-4V metallic materials. PMID:28773939

Monoclonal antibodies reactive with human breast or ovarian carcinoma: In vivo applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thor, A.D.; Edgerton, S.M.

Monoclonal antibodies (MoAbs) are unique and useful bioprobes that allow in vivo targeting of membrane-associated or circulating antigens. Most of the clinical trials to date have used low dosages of radiolabeled MoAb given in a single dose. Newer studies have included antibody fragments, repeated injections, intraperitoneal (IP) administration, and other labels such as 90Y. Clinical MoAb trials are often arduous, expensive, and time-consuming to perform. Before human use, animal studies and extensive MoAb characterization are required. The production of pharmaceutical grade, radiolabeled MoAb is technically difficult and costly. Clinical trials require administrative and patient consent as well as extensive writtenmore » protocols. These studies necessitate interdepartmental and intradepartmental cooperation and coordination. Furthermore, the use of in vivo radiolabeled probes impacts many levels of health care providers from janitorial, nursing, and technical staff to laboratories and physicians. Simple blood tests or disposal of body excretions may concern nursing or technical staff with the possibility of radiation exposure. The responsibility for study design, personnel involvement, and prospective use in patients without a definitive cancer diagnosis ultimately rests with the physician. While many issues have been addressed, additional clinical trials, consideration of safety issues, and standardization between institutions will be necessary before the use of radiolabeled MoAb for diagnosis, management, or therapy of human tumors becomes routine. Continued cooperation and funding should ensure its achievement. 136 references.« less

n-MoSe2 photoelectrochemical halogen storage cell

NASA Astrophysics Data System (ADS)

Ang, P. G. P.; Sammells, A. F.

1982-01-01

In the study reported here, single-crystal n-MoSe2 photoanodes are investigated in a variety of halogen redox couples. The photoanode is prepared by allowing the silver epoxy cement to come into contact with the front surface of the crystal before being insulated from the redox electrolyte with paraffin wax. This photoanode is evaluated in bromine redox electrolytes in various pH ranges. In 1M HBr + 1M Br2 (pH, approximately zero), the initial open-circuit potential of the MoSe2 versus a platinum reference electrode in the same electrolyte is -130 mV in the dark and -480 mV under 200 mW/sq cm xenon illumination. It is noted that improved performance could be achieved with such crystals by subjecting them to an anodic polarization of around 1 volt from the initial resting potential, a current of about 5 mA/sq cm flowing in the dark.

Atomic force microscopy studies on molybdenum disulfide flakes as sodium-ion anodes.

PubMed

Lacey, Steven D; Wan, Jiayu; von Wald Cresce, Arthur; Russell, Selena M; Dai, Jiaqi; Bao, Wenzhong; Xu, Kang; Hu, Liangbing

2015-02-11

A microscale battery comprised of mechanically exfoliated molybdenum disulfide (MoS2) flakes with copper connections and a sodium metal reference was created and investigated as an intercalation model using in situ atomic force microscopy in a dry room environment. While an ethylene carbonate-based electrolyte with a low vapor pressure allowed topographical observations in an open cell configuration, the planar microbattery was used to conduct in situ measurements to understand the structural changes and the concomitant solid electrolyte interphase (SEI) formation at the nanoscale. Topographical observations demonstrated permanent wrinkling behavior of MoS2 electrodes upon sodiation at 0.4 V. SEI formation occurred quickly on both flake edges and planes at voltages before sodium intercalation. Force spectroscopy measurements provided quantitative data on the SEI thickness for MoS2 electrodes in sodium-ion batteries for the first time.

A H2-evolving photocathode based on direct sensitization of MoS3 with an organic photovoltaic cell

PubMed Central

Bourgeteau, Tiphaine; Tondelier, Denis; Geffroy, Bernard; Brisse, Romain; Laberty-Robert, Christel; Campidelli, Stéphane; de Bettignies, Rémi; Artero, Vincent; Palacin, Serge; Jousselme, Bruno

2013-01-01

An organic solar cell based on a poly-3-hexylthiophene (P3HT): phenyl-C61-butyric acid (PCBM) bulk hetero-junction was directly coupled with molybdenum sulfide resulting in the design of a new type of photocathode for the production of hydrogen. Both the light-harvesting system and the catalyst were deposited by low-cost solution-processed methods, i.e. spin coating and spray coating respectively. Spray-coated MoS3 films are catalytically active in strongly acidic aqueous solutions with the best efficiencies for thicknesses of 40 to 90 nm. The photocathodes display photocurrents higher than reference samples, without catalyst or without coupling with a solar cell. Analysis by gas chromatography confirms the light-induced hydrogen evolution. The addition of titanium dioxide in the MoS3 film enhances electron transport and collection within thick films and therefore the performance of the photocathode. PMID:24404434

Medium-range reference evapotranspiration forecasts for the contiguous United States based on multi-model numerical weather predictions

NASA Astrophysics Data System (ADS)

Medina, Hanoi; Tian, Di; Srivastava, Puneet; Pelosi, Anna; Chirico, Giovanni B.

2018-07-01

Reference evapotranspiration (ET0) plays a fundamental role in agronomic, forestry, and water resources management. Estimating and forecasting ET0 have long been recognized as a major challenge for researchers and practitioners in these communities. This work explored the potential of multiple leading numerical weather predictions (NWPs) for estimating and forecasting summer ET0 at 101 U.S. Regional Climate Reference Network stations over nine climate regions across the contiguous United States (CONUS). Three leading global NWP model forecasts from THORPEX Interactive Grand Global Ensemble (TIGGE) dataset were used in this study, including the single model ensemble forecasts from the European Centre for Medium-Range Weather Forecasts (EC), the National Centers for Environmental Prediction Global Forecast System (NCEP), and the United Kingdom Meteorological Office forecasts (MO), as well as multi-model ensemble forecasts from the combinations of these NWP models. A regression calibration was employed to bias correct the ET0 forecasts. Impact of individual forecast variables on ET0 forecasts were also evaluated. The results showed that the EC forecasts provided the least error and highest skill and reliability, followed by the MO and NCEP forecasts. The multi-model ensembles constructed from the combination of EC and MO forecasts provided slightly better performance than the single model EC forecasts. The regression process greatly improved ET0 forecast performances, particularly for the regions involving stations near the coast, or with a complex orography. The performance of EC forecasts was only slightly influenced by the size of the ensemble members, particularly at short lead times. Even with less ensemble members, EC still performed better than the other two NWPs. Errors in the radiation forecasts, followed by those in the wind, had the most detrimental effects on the ET0 forecast performances.

Controlling Hydrogen Embrittlement in Ultra-High Strength Steels

DTIC Science & Technology

2006-06-01

this tempering temperature, (5) finely distributed, partly coherent M2C (where M = 75 at.% Cr, 13 Fe and 12 Mo) in martensite , averaging 2 nm...states in a complex precipitation hardened martensitic microstructure and is susceptible to severe hydrogen embrittlement (HE) at threshold stress...repartitions to interstitial sites proximate to the highly stressed crack tip and, subsequently, may retrap at martensitic lath interfaces to produce substantial

Hematology, Serum Chemistry, and Early Hematologic Changes in Free-Ranging South American Fur Seals ( Arctocephalus australis ) at Guafo Island, Chilean Patagonia.

PubMed

Seguel, Mauricio; Muñoz, Francisco; Keenan, Alessandra; Perez-Venegas, Diego J; DeRango, Eugene; Paves, Hector; Gottdenker, Nicole; Müller, Ananda

2016-07-01

The establishment of clinical pathology baseline data is critical to evaluate temporal and spatial changes in marine mammal groups. Despite increased availability of studies on hematology and biochemistry of marine mammals, reference ranges are lacking for many populations, especially among fur seal species. During the austral summers of 2014 and 2015, we evaluated basic hematologic and biochemical parameters in clinically healthy, physically restrained South American fur seal ( Arctocephalus australis ) lactating females and 2-mo-old pups. We also assessed the temporal variation of hematology parameters on the pups during their first 2 mo of life. Reference ranges of lactating females were similar to those previously reported in other fur seal species. In the case of pups, reference ranges are similar to values previously reported in sea lion species. As expected, most biochemical and hematologic values differ significantly between adult females and pups. As in other otariids, South American fur seals pups are born with higher values of total red blood cells, hemoglobin, and packed cell volume, and lower numbers of total leukocytes, neutrophils, lymphocytes, and eosinophils. To the best of our knowledge, data on hematology reference values for South American fur seals has not been previously reported and is useful for continued health monitoring of this species, as well as for comparisons with other otariid groups.

Prediction of gestational age based on genome-wide differentially methylated regions.

PubMed

Bohlin, J; Håberg, S E; Magnus, P; Reese, S E; Gjessing, H K; Magnus, M C; Parr, C L; Page, C M; London, S J; Nystad, W

2016-10-07

We explored the association between gestational age and cord blood DNA methylation at birth and whether DNA methylation could be effective in predicting gestational age due to limitations with the presently used methods. We used data from the Norwegian Mother and Child Birth Cohort study (MoBa) with Illumina HumanMethylation450 data measured for 1753 newborns in two batches: MoBa 1, n = 1068; and MoBa 2, n = 685. Gestational age was computed using both ultrasound and the last menstrual period. We evaluated associations between DNA methylation and gestational age and developed a statistical model for predicting gestational age using MoBa 1 for training and MoBa 2 for predictions. The prediction model was additionally used to compare ultrasound and last menstrual period-based gestational age predictions. Furthermore, both CpGs and associated genes detected in the training models were compared to those detected in a published prediction model for chronological age. There were 5474 CpGs associated with ultrasound gestational age after adjustment for a set of covariates, including estimated cell type proportions, and Bonferroni-correction for multiple testing. Our model predicted ultrasound gestational age more accurately than it predicted last menstrual period gestational age. DNA methylation at birth appears to be a good predictor of gestational age. Ultrasound gestational age is more strongly associated with methylation than last menstrual period gestational age. The CpGs linked with our gestational age prediction model, and their associated genes, differed substantially from the corresponding CpGs and genes associated with a chronological age prediction model.

Production of a pokeweed antiviral protein (PAP)-containing immunotoxin, B43-PAP, directed against the CD19 human B lineage lymphoid differentiation antigen in highly purified form for human clinical trials.

PubMed

Myers, D E; Irvin, J D; Smith, R S; Kuebelbeck, V M; Uckun, F M

1991-02-15

We describe a standardized method for the preparation and purification of a potent immunotoxin against B-lineage leukemia/lymphoma cells, constructed with the ribosome inhibitory single chain plant toxin pokeweed antiviral protein (PAP) and a murine IgG1 monoclonal antibody (MoAb) specific for the human B lineage differentiation antigen CD19 for human clinical trials. PAP was prepared from spring leaves of Phytolacca americana plants by ammonium sulfate precipitation and purified to homogeneity by successive steps of ion exchange chromatography. B43 MoAb was produced in vitro by hollow fiber technology and purified to homogeneity by affinity chromatography. PAP toxin and B43 MoAb were modified via their free amino groups prior to their intermolecular conjugation. 2-iminothiolane was used to introduce reactive sulfhydryl groups into PAP and N-succinimidyl 3-(2-pyridyldithio) propionate was used to introduce 2-pyridyl disulfide bonds into B43 MoAb. Modified PAP was reacted with modified B43 MoAb resulting in a sulfhydryl-disulfide exchange reaction and yielding disulfide linked PAP-B43 MoAb conjugates, which we refer to as B43-PAP immunotoxin. B43-PAP immunotoxin was subjected to preparative gel filtration chromatography and cation exchange chromatography to obtain a highly purified, sterile, and pyrogen-free immunotoxin preparation with less than 5% free antibody contamination and less than 0.5% free PAP contamination. The final product displayed a high affinity for and a very potent anti-leukemic activity against B lineage leukemia cells. With slight modifications, the procedures detailed in this report should be generally applicable to preparation of other PAP-MoAb conjugates for treatment of cancer or AIDS.

Levels of metabolites of organophosphate pesticides, phthalates, and bisphenol A in pooled urine specimens from pregnant women participating in the Norwegian Mother and Child Cohort Study (MoBa)

PubMed Central

Ye, Xibiao; Pierik, Frank H.; Angerer, Jürgen; Meltzer, Helle Margrete; Jaddoe, Vincent W.V.; Tiemeier, Henning; Hoppin, Jane A.; Longnecker, Matthew P.

2013-01-01

Concerns about reproductive and developmental health risks of exposure to organophosphate (OP) pesticides, phthalates, and bisphenol A (BPA) among the general population are increasing. Six dialkyl phosphate (DAP) metabolites, 3,5,6-trichloro-2-pyridinol (TCPy), BPA, and fourteen phthalate metabolites were measured in 10 pooled urine samples representing 110 pregnant women who participated in the Norwegian Mother and Child Birth Cohort (MoBa) study in 2004. Daily intakes were estimated from urinary data and compared with reference doses (RfDs) and daily tolerable intakes (TDIs). The MoBa women had a higher mean BPA concentration (4.50 μg/L) than the pregnant women in the Generation R Study (Generation R) in the Netherlands and the National Health and Nutrition Examination Survey (NHANES) in the United States. The mean concentration of total DAP metabolites (24.20 μg/L) in MoBa women was higher than that in NHANES women but lower than that in Generation R women. The diethyl phthalate metabolite mono-ethyl phthalate (MEP) was the dominant phthalate metabolite in all three studies, with the mean concentrations of greater than 300 μg/L. The MoBa and Generation R women had higher mean concentrations of mono-n-butyl phthalate (MnBP) and mono-isobutyl phthalate (MiBP) than the NHANES women. The estimated average daily intakes of BPA, chlorpyrifos/chlorpyrfios-methyl and phthalates in MoBa (and the other two studies) were below the RfDs and TDIs. The higher levels of metabolites in the MoBa participants may have been from intake via pesticide residues in food (organophosphates), consumption of canned food, especially fish/seafood (BPA), and use of personal care products (selected phthalates). PMID:19394271

Optimization of transition-metal dichalcogenides based field-effecttransistors via contact engineering

NASA Astrophysics Data System (ADS)

Perera, Meeghage Madusanka

Layered transition Metal Dichalcogenides (TMDs) have demonstrated a wide range of remarkable properties for applications in next generation nano-electronics. These systems have displayed many "graphene-like" properties including a relatively high carrier mobility, mechanical flexibility, chemical and thermal stability, and moreover offer the significant advantage of a substantial band gap. However, the fabrication of high performance field-effect transistors (FETs) of TMDs is challenging mainly due to the formation of a significant Schottky barrier at metal/TMD interface in most cases. The main goal of this study is to develop novel contact engineering strategies to achieve low-resistance Ohmic contacts. Our first approach is to use Ionic Liquid (IL) gating of metal contacted MoS2 FETs to achieve highly transparent tunneling contacts due to the strong band banding at metal/MoS2 interface. The substantially reduced contact resistance in ionic-liquid-gated bilayer and few-layer MoS 2 FETs results in an ambipolar behavior with high ON/OFF ratios, a near-ideal subthreshold swing, and significantly improved field-effect mobility. Remarkably, the mobility of a 3-nm-thick MoS2 FET with an IL gate was found to increase from ˜ 100 cm2V-1s-1 to ˜ 220 cm2V-1s-1 as the temperature decreased from 180 K to 77 K. This finding is in quantitative agreement with the true channel mobility measured by four-terminal measurement, suggesting that the mobility is predominantly limited by phonon-scattering. To further improve the contacts of TMD devices, graphene was used as work function tunable electrodes. In order to achieve low Schottky barrier height, both IL gating and surface charge transfer doping were used to tune the work function of graphene electrodes close to the conduction band edge of MoS 2. As a result, the performance of our graphene contacted MoS2 FETs is limited by the channel rather than contacts, which is further verified by four-terminal measurements. Finally, degenerately doped TMDs are used as drain/source electrodes to form 2D/2D van der Waals contacts, which are air and thermally stable. WSe2 devices with 2D/2D contacts and 0.01% Nb doped WSe2 channel show a high ON/OFF ratio and high field-effect mobility of 175 cm2 V-1S-1 at room temperature, which increases to 654 cm2V-1S-1 at cryogenic temperatures. As the doping concentration increases, both the ON/OFF ratio and mobility decrease. These contact engineering strategies overcome a major challenge in the development of electronics based on 2D materials beyond graphene.

Metallic molybdenum disulfide nanosheet-based electrochemical actuators.

PubMed

Acerce, Muharrem; Akdoğan, E Koray; Chhowalla, Manish

2017-09-21

Actuators that convert electrical energy to mechanical energy are useful in a wide variety of electromechanical systems and in robotics, with applications such as steerable catheters, adaptive wings for aircraft and drag-reducing wind turbines. Actuation systems can be based on various stimuli, such as heat, solvent adsorption/desorption, or electrochemical action (in systems such as carbon nanotube electrodes, graphite electrodes, polymer electrodes and metals). Here we demonstrate that the dynamic expansion and contraction of electrode films formed by restacking chemically exfoliated nanosheets of two-dimensional metallic molybdenum disulfide (MoS 2 ) on thin plastic substrates can generate substantial mechanical forces. These films are capable of lifting masses that are more than 150 times that of the electrode over several millimetres and for hundreds of cycles. Specifically, the MoS 2 films are able to generate mechanical stresses of about 17 megapascals-higher than mammalian muscle (about 0.3 megapascals) and comparable to ceramic piezoelectric actuators (about 40 megapascals)-and strains of about 0.6 per cent, operating at frequencies up to 1 hertz. The actuation performance is attributed to the high electrical conductivity of the metallic 1T phase of MoS 2 nanosheets, the elastic modulus of restacked MoS 2 layers (2 to 4 gigapascals) and fast proton diffusion between the nanosheets. These results could lead to new electrochemical actuators for high-strain and high-frequency applications.

Potential and Challenges of Low-Cost and High-Tech Crowd-sensing Approaches in Hydrometeorology for Better Water Resources Management - Insights and Learnings from the Global iMoMo Initiative

NASA Astrophysics Data System (ADS)

Siegfried, Tobias

2016-04-01

In developing and transition countries and despite significant global investments in hydrometeorology, data on water remain scarce/fragmented. One key reason is that traditional sensing in hydrology, hydro- and agro-meteorology does not scale because of high investment costs and difficult maintenance of traditional technology, esp. in remote and/or poor regions. Even where there are data, these are often difficult to access and interpret for local stakeholders due outdated data transmission and the lack of access to modern tools for data management/analysis/synthesis and exchange. In recent years, there have been substantial technology developments in environmental sensing and mobile communication technology that enable the application and deployment of affordable and scalable high-tech solutions for better water monitoring at different scales (local to transboundary levels). The WMO is acknowledging and promoting the potential for application of these technologies. One key aspect is to anchor these technologies in local communities that perform crowd-sensing tasks on a regular basis. The merits as well as challenges (including introduction of human factor, less accuracy as compared to traditional sensing, intermittency of data, …) of such approaches will be discussed in the context of the WMO-led Global iMoMo Initiative and its numerous activities on the ground in Eastern and Southern Africa as well as in Central Asia.

Metallic molybdenum disulfide nanosheet-based electrochemical actuators

NASA Astrophysics Data System (ADS)

Acerce, Muharrem; Akdoğan, E. Koray; Chhowalla, Manish

2017-09-01

Actuators that convert electrical energy to mechanical energy are useful in a wide variety of electromechanical systems and in robotics, with applications such as steerable catheters, adaptive wings for aircraft and drag-reducing wind turbines. Actuation systems can be based on various stimuli, such as heat, solvent adsorption/desorption, or electrochemical action (in systems such as carbon nanotube electrodes, graphite electrodes, polymer electrodes and metals). Here we demonstrate that the dynamic expansion and contraction of electrode films formed by restacking chemically exfoliated nanosheets of two-dimensional metallic molybdenum disulfide (MoS2) on thin plastic substrates can generate substantial mechanical forces. These films are capable of lifting masses that are more than 150 times that of the electrode over several millimetres and for hundreds of cycles. Specifically, the MoS2 films are able to generate mechanical stresses of about 17 megapascals—higher than mammalian muscle (about 0.3 megapascals) and comparable to ceramic piezoelectric actuators (about 40 megapascals)—and strains of about 0.6 per cent, operating at frequencies up to 1 hertz. The actuation performance is attributed to the high electrical conductivity of the metallic 1T phase of MoS2 nanosheets, the elastic modulus of restacked MoS2 layers (2 to 4 gigapascals) and fast proton diffusion between the nanosheets. These results could lead to new electrochemical actuators for high-strain and high-frequency applications.

Mapping Catalytically Relevant Edge Electronic States of MoS2

PubMed Central

2018-01-01

Molybdenum disulfide (MoS2) is a semiconducting transition metal dichalcogenide that is known to be a catalyst for both the hydrogen evolution reaction (HER) as well as for hydro-desulfurization (HDS) of sulfur-rich hydrocarbon fuels. Specifically, the edges of MoS2 nanostructures are known to be far more catalytically active as compared to unmodified basal planes. However, in the absence of the precise details of the geometric and electronic structure of the active catalytic sites, a rational means of modulating edge reactivity remain to be developed. Here we demonstrate using first-principles calculations, X-ray absorption spectroscopy, as well as scanning transmission X-ray microscopy (STXM) imaging that edge corrugations yield distinctive spectroscopic signatures corresponding to increased localization of hybrid Mo 4d states. Independent spectroscopic signatures of such edge states are identified at both the S L2,3 and S K-edges with distinctive spatial localization of such states observed in S L2,3-edge STXM imaging. The presence of such low-energy hybrid states at the edge of the conduction band is seen to correlate with substantially enhanced electrocatalytic activity in terms of a lower Tafel slope and higher exchange current density. These results elucidate the nature of the edge electronic structure and provide a clear framework for its rational manipulation to enhance catalytic activity. PMID:29721532

Supplementation of Infant Formula with Bovine Milk Fat Globule Membranes.

PubMed

Timby, Niklas; Domellöf, Magnus; Lönnerdal, Bo; Hernell, Olle

2017-03-01

Studies have shown that supplementation of infant formula with bovine milk fat globule membranes (MFGMs) may substantially narrow the gap in health outcomes between formula-fed and breastfed infants. In one study, consumption of a formula supplemented with a lipid-rich MFGM concentrate between 2 and 6 mo of age improved cognitive performance at 24 wk of age. In another study, a formula supplemented with a protein-rich MFGM concentrate given between 2 and 6 mo of age improved cognitive performance at 12 mo of age, decreased infectious morbidity until 6 mo of age, and yielded serum cholesterol concentrations closer to those of breastfed infants. A third study that assessed the safety of supplementing infant formula with a lipid-rich or a protein-rich MFGM concentrate found a noninferior weight gain for both groups compared with a nonsupplemented formula. In this study, there was an increased risk of eczema in the protein-rich group, but no serious adverse events. Infant formulas with supplemental MFGMs have been launched on the market in several countries. However, the evidence base must still be considered quite limited. Based on 3 randomized controlled trials that are not comparable, the intervention seems safe, but there is not enough evidence for a general recommendation on which MFGM fraction to use and at what concentration as formula supplement for a given outcome. © 2017 American Society for Nutrition.

The impact of reference pricing and extension of generic substitution on the daily cost of antipsychotic medication in Finland.

PubMed

Koskinen, Hanna; Ahola, Elina; Saastamoinen, Leena K; Mikkola, Hennamari; Martikainen, Jaana E

2014-12-01

To assess the impact of reference pricing and extension of generic substitution on the daily cost of antipsychotic drugs in Finland during the first year after its launch. Furthermore, the additional impact of reference pricing on prior implemented generic substitution is assessed. A retrospective analysis was performed between 2006 and 2010. A segmented linear regression analysis of interrupted time series was used to estimate changes in the levels and trends in the cost of one day of treatment. Of the study drugs, clozapine belonged to generic substitution already at the start of the study period while olanzapine and quetiapine were included in generic substitution alongside with reference pricing in 2009. Risperidone was included in generic substitution in 2008, before reference pricing. A substantial decrease in the daily cost of all four antipsychotic substances was seen after one year of the implementation of reference pricing and the extension of generic substitution. The impact ranged from -29.9% to -66.3%, and it was most substantial on the daily cost of olanzapine. Also in the daily cost of risperidone a substantial decrease of -43.3% was observed. However, most of these savings, -32.6%, were generated by generic substitution which had been adopted prior. Reference pricing and the extension of generic substitution produced substantial savings on antipsychotic medication costs during the first year after its launch, but the intensity of the impact differed between active substances. Furthermore, our results suggest that the additional cost savings from reference pricing after prior implemented generic substitution, are comparatively low.

Non-covalent doping of graphitic carbon nitride with ultrathin graphene oxide and molybdenum disulfide nanosheets: an effective binary heterojunction photocatalyst under visible light irradiation.

PubMed

Hu, S W; Yang, L W; Tian, Y; Wei, X L; Ding, J W; Zhong, J X; Chu, Paul K

2014-10-01

A proof of concept integrating binary p-n heterojunctions into a semiconductor hybrid photocatalyst is demonstrated by non-covalent doping of graphite-like carbon nitride (g-C3N4) with ultrathin GO and MoS2 nanosheets using a facile sonochemical method. In this unique ternary hybrid, the layered MoS2 and GO nanosheets with a large surface area enhance light absorption to generate more photoelectrons. On account of the coupling between MoS2 and GO with g-C3N4, the ternary hybrid possesses binary p-n heterojunctions at the g-C3N4/MoS2 and g-C3N4/GO interfaces. The space charge layers created by the p-n heterojunctions not only enhance photogeneration, but also promote charge separation and transfer of electron-hole pairs. In addition, the ultrathin MoS2 and GO with high mobility act as electron mediators to facilitate separation of photogenerated electron-hole pairs at each p-n heterojunction. As a result, the ternary hybrid photocatalyst exhibits improved photoelectrochemical and photocatalytic activity under visible light irradiation compared to other reference materials. The results provide new insights into the large-scale production of semiconductor photocatalysts. Copyright © 2014 Elsevier Inc. All rights reserved.

Quenching Mo optical losses in CIGS solar cells by a point contacted dual-layer dielectric spacer: a 3-D optical study.

PubMed

Rezaei, Nasim; Isabella, Olindo; Vroon, Zeger; Zeman, Miro

2018-01-22

A 3-D optical modelling was calibrated to calculate the light absorption and the total reflection of fabricated CIGS solar cells. Absorption losses at molybdenum (Mo) / CIGS interface were explained in terms of plasmonic waves. To quench these losses, we assumed the insertion of a lossless dielectric spacer between Mo and CIGS, whose optical properties were varied. We show that such a spacer with low refractive index and proper thickness can significantly reduce absorption in Mo in the long wavelength regime and improve the device's rear reflectance, thus leading to enhanced light absorption in the CIGS layer. Therefore, we optimized a realistic two-layer MgF 2 / Al 2 O 3 dielectric spacer to exploit (i) the passivation properties of ultra-thin Al 2 O 3 on the CIGS side for potential high open-circuit voltage and (ii) the low refractive index of MgF 2 on the Mo side to reduce its optical losses. Combining our realistic spacer with optically-optimized point contacts increases the implied photocurrent density of a 750 nm-thick CIGS layer by 10% for the wavelengths between 700 and 1150 nm with respect to the reference cell. The elimination of plasmonic resonances in the new structure leads to a higher electric field magnitude at the bottom of CIGS layer and justifies the improved optical performance.

National Dam Safety Program. Hunter Dam (MO 10029), Mississippi - Kaskaskia - St. Louis Basin, St. Louis County, Missouri. Phase I Inspection Report.

DTIC Science & Technology

1978-06-01

EDTION oF I NOV6S IS oBSOLETE EJUN I UNCLASSIFIED SECuRiITY CLASSIICATION OF THIS PAGE (Whon Datai Entered) SECURtITY CLASSIFICATION OF THIS PAO9(Whou...moveable. Since the watershed area is essentially one- third square mile with a time of concentration of flows substantially less than an hour, no

Exploring the Mode of Action of Bioactive Compounds by Microfluidic Transcriptional Profiling in Mycobacteria

PubMed Central

Lim, Vivian; Naim, Ahmad Nazri Mohamed; Bifani, Pablo; Boshoff, Helena I. M.; Sambandamurthy, Vasan K.; Dick, Thomas; Hibberd, Martin L.; Schreiber, Mark; Rao, Srinivasa P. S.

2013-01-01

Most candidate anti-bacterials are identified on the basis of their whole cell anti-bacterial activity. A critical bottleneck in the early discovery of novel anti-bacterials is tracking the structure activity relationship (SAR) of the novel compounds synthesized during the hit to lead and lead optimization stage. It is often very difficult for medicinal chemists to visualize if the novel compounds synthesized for understanding SAR of a particular scaffold have similar molecular mechanism of action (MoA) as that of the initial hit. The elucidation of the molecular MoA of bioactive inhibitors is critical. Here, a new strategy and routine assay for MoA de-convolution, using a microfluidic platform for transcriptional profiling of bacterial response to inhibitors with whole cell activity has been presented. First a reference transcriptome compendium of Mycobacterial response to various clinical and investigational drugs was built. Using feature reduction, it was demonstrated that subsets of biomarker genes representative of the whole genome are sufficient for MoA classification and deconvolution in a medium-throughput microfluidic format ultimately leading to a cost effective and rapid tool for routine antibacterial drug-discovery programs. PMID:23935951

Isolation and identification of a lethal rhabdovirus from farmed rice field eels Monopterus albus.

PubMed

Ou, Tong; Zhu, Ruo-Lin; Chen, Zhong-Yuan; Zhang, Qi-Ya

2013-11-06

We provide the first description of a virus responsible for a systemic hemorrhagic disease causing high mortality in farmed rice field eels Monopterus albus in China. Typical signs exhibited by the diseased fish were extensive hemorrhages in the skin and viscera and some neurological signs, such as loss of equilibrium and disorganized swimming. Histopathological examination revealed various degrees of necrosis within the spleen and liver. Virus isolation was attempted from visceral tissues of diseased fish by inoculation on 6 fish cell lines. Typical cytopathic effects (CPE) were produced in bluegill fry (BF2) cells, so this cell line was chosen for further isolation and propagation of the virus. Electron microscopy observation showed that the negative stained viral particles had the characteristic bullet shape of rhabdoviruses and an estimated size of 60 × 120 nm. We therefore tentatively refer to this virus as Monopterus albus rhabdovirus (MoARV). Molecular characterization of MoARV, including sequence analysis of the nucleoprotein (N), phosphoprotein (P), and glycoprotein (G) genes, revealed 94.5 to 97.3% amino acid similarity to that of Siniperca chuatsi rhabdovirus. Phylogenetic analysis based on the amino acid sequences of N and G proteins indicated that MoARV should be a member of the genus Vesiculovirus. Koch's postulates were fulfilled by infecting healthy rice field eels with MoARV, which produced an acute infection. RT-PCR analysis demonstrated that MoARV RNA could be detected in both naturally and experimentally infected fish. The data suggest that MoARV was the causative pathogen of the disease.

Periprosthetic pathology in 'at risk' ceramic-on-polyethylene total hip arthroplasty: a clinical study using MARS-MRI in 50 patients.

PubMed

Das, Dirk H; van der Weegen, Walter; Wullems, Jorgen A; Brakel, Koen; Sijbesma, Thea; Nelissen, Rob G

2016-05-16

Recent studies of metal-on-metal (MoM) total hip arthroplasty (THA) using metal-artefact-reducing-sequence software for magnetic resonance Imaging (MARS-MRI) have revealed remarkable soft tissue pathology around the hip, usually referred to as pseudotumours. Case reports describe identical pathology in non-MoM THA, but descriptive overviews of MRI abnormalities in patients with non-MoM prosthesis are scarce. A clinical study in a cohort of 50 ceramic-on-polyethylene (CoP) THA selected for high risk of peri-prosthetic pathology including 2 subgroups: (i) 40 patients with a high polyethylene (PE) wear rate (>0.2 mm per year) and 5-12 years follow-up; (ii) 10 patients with a 2 to 5 years follow-up and a documented history of persistent complaints. All patients were clinically evaluated, MARS-MRIs were completed and chrome and cobalt serum samples were taken. 17 scans were normal (34%). Periprosthetic fluid collections were seen as a bursae iliopsoas (n = 12, 24%), in the trochanter bursae (n = 4, 8%) and in the surgical tract (n = 9, 18%). 1 case demonstrated a cyst on MARS-MRI resembling a pseudotumour as seen with MoM THA (2%). Intraosseous acetabular cysts were seen in 12 cases (24%), intraosseous trochanteric cysts in 10 cases (20%). Soft tissue abnormalities after non-MoM THA are common in selected patients and can be clearly visualised with MARS-MRI. Pseudotumours as seen on MARS-MRI do occur in non-MoM hip arthroplasty but with low prevalence.

The late Variscan ferroan granite magmatism of southern Sardinia: inferences from Mo metallogenesis

NASA Astrophysics Data System (ADS)

Naitza, Stefano; Conte, Aida Maria; Cuccuru, Stefano; Fadda, Sandro; Fiori, Maddalena; Oggiano, Giacomo; Secchi, Francesco

2017-04-01

Metallogeny is a powerful tool to investigate crustal evolution; a good example is offered by the Variscan basement of Sardinia and its Mo deposits. Mo ores are poorly represented in Variscan metallogenic provinces of Europe: however, in Sardinia, numerous small Mo deposits, often associated to Sn, W and F ores, are present, invariably related to an early Permian intrusive peak bracketed at about 290 Ma (Fadda et al., 2015; Naitza et al., 2017). In Sardinia, two main magmatic peaks have been schematized at pre-300 and 290 Ma. In southern Sardinia, the 290 magmatic peak is made up of several intrusive F-bearing rock-suites (Conte et al., 2016), belonging to ilmenite series, showing a slight peraluminous character and mostly classifiable as ferroan granites (sensu Frost and Frost, 2011). Mo-bearing granites form a distinct suite of relatively small plutons, emplaced at very shallow depth (about 1kb) in an exhumed Variscan low-grade basement. Peculiar characters of Mo-bearing granites are the occurrence of greisenized microgranite and granophyre cupolas, with fayalite-bearing pegmatites, and ilmenite, xenotime-(Y), monazite, fluorite, and local topaz as accessory phases. Recently, Conte et al. (2016) interpreted these granites as originated by partial melting of low crustal felsic metaigneous photoliths enriched in granophiles (Mo, Sn, W). Mo ores occur as: a) endo- and exo- quartz-muscovite greisens with molybdenite±Fe-Cu sulphides, and b) quartz-molybdenite±wolframite±Fe-Cu-Zn sulphides±fluorite±topaz hydrothermal veins and stockworks, hosted in granites or in country rocks. Redox state of magmas exerts a strong control on Mo metallogeny, as in Mo districts worldwide ores are usually hosted by high-fO2 magnetite series intrusions (Ishihara, 1981). The close field association of Sardinian Mo mineralization with ferroan, low-fO2 ilmenite-series granites may be explained in terms of Mo-enriched crustal sources of magmas, and very efficient geochemical concentration processes. Mo concentration occurred during latest intrusive phases in granitic cupolas, as local subsolidus reactions. They involve: 1) leaching of Mo5+ and Mo6+ from their primary hosts (e.g., biotites) by Cl- and F-rich fluids under decreasing pH and increasing fH2O and fO2, and 2) transport of Mo cations towards intrusive contacts, where they quickly reacted with Sulphur from country rocks to be reduced as MoS2. Overall, the late Variscan Mo metallogenic peak in Sardinia is a single event located in a short timespan at around 290 Ma. In the early Permian extensional setting of Corsica-Sardinia batholith, a distinct HT/LP event related to melting of mantle lithosphere (Rossi et al., 2015), triggered partial melting of Mo-bearing deep crustal sources, producing the F-bearing ferroan magmas. The singular concentration of Mo-bearing granites could indicate a peculiar compositional character of the Sardinian lower crust. References: Conte A.M. et al. (2016). Proc. 2nd European Mineralogical Conference, Rimini, Italy, 154. Fadda et al. (2015). Proc. 13th Biennial SGA Meeting, Nancy, France, Vol. 2, 721-724. Frost, C. D. and Frost R. B. (2011). J. Petrol. 52, 39-53. Ishihara S. (1981). Econ. Geol., 75th Anniversary Volume, 458-484. Naitza S. et al. (2017). Ore Geol. Rev. 80, 1259-1278. Rossi et al. (2015). Bull. Soc. Géol. France 186, 171-192.

Can Ni phosphides become viable hydroprocessing catalysts?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Soled, S.; Miseo, S.; Baumgartner, J.

2015-05-15

We prepared higher surface area nickel phosphides than are normally found by reducing nickel phosphate. To do this, we hydrothermally synthesized Ni hydroxy phosphite precursors with low levels of molybdenum substitution. The molybdenum substitution increases the surface area of these precursors. During pretreatment in a sulfiding atmosphere (such as H2S/H2) dispersed islands of MoS2 segregate from the precursor and provide a pathway for H2 dissociation that allows reduction of the phosphite precursor to nickel phosphide at substantially lower temperatures than in the absence of MoS2. The results reported here show that to create nickel phosphides with comparable activity to conventionalmore » supported sulfide catalysts, one would have to synthesize the phosphide with surface areas exceeding 400 m2/g (i.e. with nanoparticles less than 30 Å in lateral dimension).« less

The effect of cassia fistula emulsion on pediatric functional constipation in comparison with mineral oil: a randomized, clinical trial

PubMed Central

2012-01-01

Background The prevalence of Pediatric Functional Constipation (FC) has been reported between 0.7% to 29.6%. This study was conducted to compare the laxative effect of cassia fistula emulsion (CFE) with mineral oil (MO) on FC. Cassia fistula is named in Traditional Iranian Medicine (TIM) as “Folus”. Materials and methods A randomized clinical trial was carried on 81 children (age range: 4–13 years) with FC, according to Rome III criteria in Amirkola Children’s Hospital, Babol, Iran. They received CFE or MO randomly for three weeks. CFE was produced according to the order of TIM references. Children were counted as improved when they exited from Rome III criteria of FC. Frequency of defecation, fecal incontinence, retentive posturing, severity of pain, consistency of stool and anal leakage of oily material were compared between the two groups and with baselines. An intent-to-treat analysis was used. Safety of drugs was assessed with the evaluation of clinical adverse effects. Results 41 children were assigned randomly to receive CFE and 40 children received MO. After three weeks of medication, 84% of children in CFE group and 50% in MO group (p = 0.002) exited from the criteria of FC, so called improved. All measurable criteria improved in both groups. The frequency of defecation in CFE group improved from 1.7 per week (before the study) to 10.6 per week (at the third week) while this parameter differed in MO group from 2 to 6.1 (p < 0.001). The severity of pain during defecation and consistency of stool improved significantly better in CFE group than MO group (p < 0.05), but there were not any significant differences between the two groups in fecal incontinence and retentive posturing. Anal leakage of oily material occurred as an important complication in MO group while the children in CFE group did not complaint it. Drug’s compliances were not significantly different in the two groups. CFE and MO did not cause clinically significant side effects. Conclusions CFE was most effective than MO in the 3-week treatment of children with FC. PMID:23351337

77 FR 44238 - Proposed Administrative Cost Recovery Settlement Under the Comprehensive Environmental Response...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-27

... Amended, Big River Mine Tailings Superfund Site, St. Francois County, MO AGENCY: Environmental Protection.... Louis, Missouri, for recovery of past response costs concerning the Big River Mine Tailings Superfund..., Kansas City, Kansas, (913) 551-7567. Requests should reference the Big River Mine Tailings Superfund Site...

The Chemistry of Optical Discs.

ERIC Educational Resources Information Center

Birkett, David

2002-01-01

Explains the chemistry used in compact discs (CD), digital versatile discs (DVD), and magneto-optical (MO) discs focusing on the steps of initial creation of the mold, the molding of the polycarbonate, the deposition of the reflective layers, the lacquering of the CDs, and the bonding of DVDs. (Contains 15 references.) (YDS)

Ohmic Contact Fabrication Using a Focused-ion Beam Technique and Electrical Characterization for Layer Semiconductor Nanostructures.

PubMed

Chen, Ruei-San; Tang, Chih-Che; Shen, Wei-Chu; Huang, Ying-Sheng

2015-12-05

Layer semiconductors with easily processed two-dimensional (2D) structures exhibit indirect-to-direct bandgap transitions and superior transistor performance, which suggest a new direction for the development of next-generation ultrathin and flexible photonic and electronic devices. Enhanced luminescence quantum efficiency has been widely observed in these atomically thin 2D crystals. However, dimension effects beyond quantum confinement thicknesses or even at the micrometer scale are not expected and have rarely been observed. In this study, molybdenum diselenide (MoSe2) layer crystals with a thickness range of 6-2,700 nm were fabricated as two- or four-terminal devices. Ohmic contact formation was successfully achieved by the focused-ion beam (FIB) deposition method using platinum (Pt) as a contact metal. Layer crystals with various thicknesses were prepared through simple mechanical exfoliation by using dicing tape. Current-voltage curve measurements were performed to determine the conductivity value of the layer nanocrystals. In addition, high-resolution transmission electron microscopy, selected-area electron diffractometry, and energy-dispersive X-ray spectroscopy were used to characterize the interface of the metal-semiconductor contact of the FIB-fabricated MoSe2 devices. After applying the approaches, the substantial thickness-dependent electrical conductivity in a wide thickness range for the MoSe2-layer semiconductor was observed. The conductivity increased by over two orders of magnitude from 4.6 to 1,500 Ω(-) (1) cm(-) (1), with a decrease in the thickness from 2,700 to 6 nm. In addition, the temperature-dependent conductivity indicated that the thin MoSe2 multilayers exhibited considerably weak semiconducting behavior with activation energies of 3.5-8.5 meV, which are considerably smaller than those (36-38 meV) of the bulk. Probable surface-dominant transport properties and the presence of a high surface electron concentration in MoSe2 are proposed. Similar results can be obtained for other layer semiconductor materials such as MoS2 and WS2.

Electrocatalysis using transition metal carbide and oxide nanocrystals

NASA Astrophysics Data System (ADS)

Regmi, Yagya N.

Carbides are one of the several families of transition metal compounds that are considered economic alternatives to catalysts based on noble metals and their compounds. Phase pure transition metal carbides of group 4-6 metals, in the first three periods, were synthesized using a common eutectic salt flux synthesis method, and their electrocatalytic activities compared under uniform electrochemical conditions. Mo2C showed highest hydrogen evolution reaction (HER) and oxygen reduction reaction (ORR) activities among the nine metal carbides investigated, but all other metal carbides also showed substantial activities. All the metal carbides showed remarkable enhancement in catalytic activities as supports, when compared to traditional graphitic carbon as platinum support. Mo2C, the most active transition metal carbide electrocatalyst, was prepared using four different synthesis routes, and the synthesis route dependent activities compared. Bifunctional Mo 2C that is HER as well as oxygen evolution reaction (OER) active, was achieved when the carbide was templated on a multiwalled carbon nanotube using carbothermic reduction method. Bimetallic carbides of Fe, Co, and Ni with Mo or W were prepared using a common carbothermic reduction method. Two different stoichiometries of bimetallic carbides were obtained for each system within a 60 °C temperature window. While the bimetallic carbides showed relatively lower electrocatalytic activities towards HER and ORR in comparison to Mo2C and WC, they revealed remarkably higher OER activities than IrO2 and RuO2, the state-of-the-art OER catalysts. Bimetallic oxides of Fe, Co, and Ni with Mo and W were also prepared using a hydrothermal synthesis method and they also revealed OER activities that are much higher than RuO2 and IrO2. Additionally, the OER activities were dependent on the degree and nature of hydration in the bimetallic oxide crystal lattice, with the completely hydrated, as synthesized, cobalt molybdate and nickel molybdate showing the highest OER activities.

Pathway and Surface Mechanism Studies of 1,3-butadiene Selective Oxidation Over Vanadium-Molybdenum-Oxygen Catalysts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schroeder, William David

2001-01-01

The partial oxidation of 1,3-butadiene has been investigated over VMoO catalysts synthesized by sol-gel techniques. Surface areas were 9-14 m 2/g, and compositions were within the solid solution regime, i.e. below 15.0 mol % MoO 3/(MoO 3 + V 2O 5). Laser Raman Spectroscopy and XRD data indicated that solid solutions were formed, and pre- and post-reaction XPS data indicated that catalyst surfaces contained some V +4 and were further reduced in 1,3-butadiene oxidation. A reaction pathway for 1,3-butadiene partial oxidation to maleic anhydride was shown to involve intermediates such as 3,4-epoxy-1-butene, crotonaldehyde, furan, and 2-butene-1,4-dial. The addition of watermore » to the reaction stream substantially increased catalyst activity and improved selectivity to crotonaldehyde and furan at specific reaction temperatures. At higher water addition concentrations, furan selectivity increased from 12% to over 25%. The catalytic effects of water addition were related to competitive adsorption with various V 2O 5-based surface sites, including the vanadyl V=O, corner sharing V-O-V and edge sharing V-O oxygen. Higher levels of water addition were proposed to impose acidic character by dissociative adsorption. In addition, a novel combinatorial synthesis technique for VMoO was used to investigate the phase transitions of V 2O 5, solid solutions of Mo in V 2O 5, V 9Mo 6O 40, and other reduced VMoO compounds, characterized by laser Raman spectroscopy. The natural composition gradient imposed by the sputter deposition apparatus was used to create VMoO arrays containing 225 samples ranging from 7.0-42 mol% MoO 3/(V 2O 5 + MoO 3), determined by EDS analysis.« less

Ohmic Contact Fabrication Using a Focused-ion Beam Technique and Electrical Characterization for Layer Semiconductor Nanostructures

PubMed Central

Chen, Ruei-San; Tang, Chih-Che; Shen, Wei-Chu; Huang, Ying-Sheng

2015-01-01

Layer semiconductors with easily processed two-dimensional (2D) structures exhibit indirect-to-direct bandgap transitions and superior transistor performance, which suggest a new direction for the development of next-generation ultrathin and flexible photonic and electronic devices. Enhanced luminescence quantum efficiency has been widely observed in these atomically thin 2D crystals. However, dimension effects beyond quantum confinement thicknesses or even at the micrometer scale are not expected and have rarely been observed. In this study, molybdenum diselenide (MoSe2) layer crystals with a thickness range of 6-2,700 nm were fabricated as two- or four-terminal devices. Ohmic contact formation was successfully achieved by the focused-ion beam (FIB) deposition method using platinum (Pt) as a contact metal. Layer crystals with various thicknesses were prepared through simple mechanical exfoliation by using dicing tape. Current-voltage curve measurements were performed to determine the conductivity value of the layer nanocrystals. In addition, high-resolution transmission electron microscopy, selected-area electron diffractometry, and energy-dispersive X-ray spectroscopy were used to characterize the interface of the metal–semiconductor contact of the FIB-fabricated MoSe2 devices. After applying the approaches, the substantial thickness-dependent electrical conductivity in a wide thickness range for the MoSe2-layer semiconductor was observed. The conductivity increased by over two orders of magnitude from 4.6 to 1,500 Ω−1 cm−1, with a decrease in the thickness from 2,700 to 6 nm. In addition, the temperature-dependent conductivity indicated that the thin MoSe2 multilayers exhibited considerably weak semiconducting behavior with activation energies of 3.5-8.5 meV, which are considerably smaller than those (36-38 meV) of the bulk. Probable surface-dominant transport properties and the presence of a high surface electron concentration in MoSe2 are proposed. Similar results can be obtained for other layer semiconductor materials such as MoS2 and WS2. PMID:26710105

Manganese oxide shuttling in pre-GOE oceans - evidence from molybdenum and iron isotopes

NASA Astrophysics Data System (ADS)

Kurzweil, Florian; Wille, Martin; Gantert, Niklas; Beukes, Nicolas J.; Schoenberg, Ronny

2016-10-01

The local occurrence of oxygen-rich shallow marine water environments has been suggested to significantly predate atmospheric oxygenation, which occurred during the Great Oxidation Event (GOE) ca. 2.4 billion years ago. However, the potential influence of such 'oxygen oases' on the mobility, distribution and isotopic composition of redox sensitive elements remains poorly understood. Here, we provide new molybdenum and iron isotopic data from shallow marine carbonate and silicate iron formations of the Koegas Subgroup, South Africa, that confirm local ocean redox stratification prior to the GOE. Mn concentrations correlate negatively with both δ98 Mo and δ56 Fe values, which highlights the substantial role of particulate manganese for the cycling of Mo and Fe in the Paleoproterozoic oceans. Based on these trends we propose that pore water molybdate was recharged (1) by the diffusional transport of seawater molybdate with high δ98 Mo and (2) by the re-liberation of adsorbed molybdate with low δ98 Mo during Mn oxide dissolution within the sediment. The relative contribution of isotopically light Mo is highest close to a Mn chemocline, where the flux of Mn oxides is largest, causing the negative correlation of Mn concentrations and δ98 Mo values in the Koegas sediments. The negative correlation between δ56 Fe values and Mn concentrations is likely related to Fe isotope fractionation during Fe(II) oxidation by Mn oxides, resulting in lower δ56 Fe values in the uppermost water column close to a Mn chemocline. We argue that the preservation of these signals within Paleoproterozoic sediments implies the existence of vertically extended chemoclines with a smoother gradient, probably as a result of low atmospheric oxygen concentrations. Furthermore, we suggest that abiotic oxidation of Fe(II) by a Mn oxide particle shuttle might have promoted the deposition of the Koegas iron formations.

Sleep Quality Among Low-Income Young Women in Southeast Texas Predicts Changes in Perceived Stress Through Hurricane Ike.

PubMed

Wu, Zhao Helen; Stevens, Richard G; Tennen, Howard; North, Carol S; Grady, James J; Holzer, Charles

2015-07-01

To document the time course of perceived stress among women through the period of a natural disaster, to determine the effect of sleep quality on this time course, and to identify risk factors that predict higher levels of perceived stress. Longitudinal study from 2006-2012. Community-based family planning clinics in southeast Texas. There were 296 women aged 18-31 y who experienced Hurricane Ike, September 2008. Cohen Perceived Stress Scale (PSS) was administered every 2 mo from 6 mo before to 12 mo after Hurricane Ike. Sleep quality was assessed 1 mo after Hurricane Ike using the Pittsburg Sleep Quality Index (PSQI). Good sleep was defined as a PSQI summary score < 5, and poor sleep as a score ≥ 5. Hurricane Ike stressors (e.g., property damage, subjective stressors) and pre-Ike lifetime major life events and emotional health (e.g., emotional dysregulation, self-control) were also assessed. Over the entire period of 18 mo (6 mo before and 12 mo after the hurricane), perceived stress was significantly higher among poor sleepers compared to good sleepers, and only good sleepers showed a significant decrease in perceived stress after Hurricane Ike. In addition, a higher level of perceived stress was positively associated with greater Ike damage among poor sleepers, whereas this correlation was not observed among good sleepers. In the final multivariate longitudinal model, Ike-related subjective stressors as well as baseline major life events and emotional dysregulation among poor sleepers predicted higher levels of perceived stress over time; among good sleepers, additional factors such as lower levels of self-control and having a history of a psychiatric disorder also predicted higher levels of perceived stress. Sleep quality after Hurricane Ike, an intense natural disaster producing substantial damage, impacted changes in perceived stress over time. Our findings suggest the possibility that providing victims of disasters with effective interventions to improve sleep quality could help to reduce their perceived stress over time. © 2015 Associated Professional Sleep Societies, LLC.

Treatment with Myf5-morpholino results in somite patterning and brain formation defects in zebrafish.

PubMed

Chen, Yau-Hung; Tsai, Huai-Jen

2002-10-01

Myf-5 is a stage-dependent transcription factor associated with somitogenesis. To study its biological functions in zebrafish, we injected the Myf5-morpholinos ZMF-MO (antisense nucleotides 28 to 52) and ZMF-OTHER (antisense nucleotides 3 to 27) into zebrafish embryos to establish a myf-5 gene knockdown. No phenotypic abnormalities were observed following injection with 0.2 ng of ZMF-MO, but defects were displayed in 2 of 118 (1.7%) surviving embryos injected with 1 ng ZMF-MO. Morphological defects became more severe with increased dosages: 105 of 270 (38.9%) surviving embryos injected with 4.5 ng of ZMF-MO displayed such abnormalities as the absence of eyes or brains in addition to the following low-dosage defects in 24 hpf embryos: longitudinal yolk sacs, incomplete epiboly coverage, abnormal and suspended tail buds, diffused somite boundaries, and head shrinkage. Similar results were observed in the 4.5 ng ZMF-OTHER injection group. However, when fish were co-injected with 4.5 ng ZMF-MO and 4.5 ng myf-5 mRNA, abnormality rates decreased from 49.6% to 5.5%. Our results show that the brain krox20 gene was down-regulated at rhombomere 3; the pax2.1 gene was completely down-regulated; myoD was expressed normally; myogenin was substantially down-regulated in whole somites; and desmin was partly inhibited in newly forming somites. Our conclusion is that zebrafish Myf-5 may play important roles in brain formation and in the convergence and extension of shield epiblasts and tail buds during early embryogenesis, in addition to its well-understood role as a muscle regulatory factor in somites.

ACTIVATION OF TRPA1 ON DURAL AFFERENTS: A POTENTIAL MECHANISM OF HEADACHE PAIN

PubMed Central

Edelmayer, Rebecca M.; Le, Larry N.; Yan, Jin; Wei, Xiaomei; Nassini, Romina; Materazzi, Serena; Preti, Delia; Appendino, Giovanni; Geppetti, Pierangelo; Dodick, David W.; Vanderah, Todd W.; Porreca, Frank; Dussor, Gregory

2012-01-01

Activation of transient receptor potential ankyrin-1 (TRPA1) on meningeal nerve endings has been suggested to contribute to environmental irritant-induced headache but this channel may also contribute to other forms of headache such as migraine. The preclinical studies described here examined functional expression of TRPA1 on dural afferents and investigated whether activation of TRPA1 contributes to headache-like behaviors. Whole-cell patch-clamp recordings were performed in vitro using two TRPA1 agonists, mustard oil (MO) and the environmental irritant umbellulone (UMB), on dural-projecting trigeminal ganglion neurons. Application of MO and UMB to dural afferents produced TRPA1-like currents in approximately 42% and 38% of cells, respectively. Using an established in vivo behavioral model of migraine-related allodynia, dural application of MO and UMB produced robust time-related tactile facial and hindpaw allodynia that was attenuated by pretreatment with the TRPA1 antagonist HC-030031. Additionally, MO or UMB were applied to the dura and exploratory activity was monitored for 30 minutes using an automated open-field activity chamber. Dural MO and UMB decreased the number of vertical rearing episodes and the time spent rearing in comparison to vehicle treated animals. This change in activity was prevented in rats pretreated with HC-030031 as well as sumatriptan, a clinically effective anti-migraine agent. These data indicate that TRPA1 is expressed on a substantial fraction of dural afferents and activation of meningeal TRPA1 produces behaviors consistent with those seen in patients during migraine attacks. Further, they suggest that activation of meningeal TRPA1 via endogenous or exogenous mechanisms can lead to afferent signaling and headache. PMID:22809691

Differences in Gaussian diffusion tensor imaging and non-Gaussian diffusion kurtosis imaging model-based estimates of diffusion tensor invariants in the human brain.

PubMed

Lanzafame, S; Giannelli, M; Garaci, F; Floris, R; Duggento, A; Guerrisi, M; Toschi, N

2016-05-01

An increasing number of studies have aimed to compare diffusion tensor imaging (DTI)-related parameters [e.g., mean diffusivity (MD), fractional anisotropy (FA), radial diffusivity (RD), and axial diffusivity (AD)] to complementary new indexes [e.g., mean kurtosis (MK)/radial kurtosis (RK)/axial kurtosis (AK)] derived through diffusion kurtosis imaging (DKI) in terms of their discriminative potential about tissue disease-related microstructural alterations. Given that the DTI and DKI models provide conceptually and quantitatively different estimates of the diffusion tensor, which can also depend on fitting routine, the aim of this study was to investigate model- and algorithm-dependent differences in MD/FA/RD/AD and anisotropy mode (MO) estimates in diffusion-weighted imaging of human brain white matter. The authors employed (a) data collected from 33 healthy subjects (20-59 yr, F: 15, M: 18) within the Human Connectome Project (HCP) on a customized 3 T scanner, and (b) data from 34 healthy subjects (26-61 yr, F: 5, M: 29) acquired on a clinical 3 T scanner. The DTI model was fitted to b-value =0 and b-value =1000 s/mm(2) data while the DKI model was fitted to data comprising b-value =0, 1000 and 3000/2500 s/mm(2) [for dataset (a)/(b), respectively] through nonlinear and weighted linear least squares algorithms. In addition to MK/RK/AK maps, MD/FA/MO/RD/AD maps were estimated from both models and both algorithms. Using tract-based spatial statistics, the authors tested the null hypothesis of zero difference between the two MD/FA/MO/RD/AD estimates in brain white matter for both datasets and both algorithms. DKI-derived MD/FA/RD/AD and MO estimates were significantly higher and lower, respectively, than corresponding DTI-derived estimates. All voxelwise differences extended over most of the white matter skeleton. Fractional differences between the two estimates [(DKI - DTI)/DTI] of most invariants were seen to vary with the invariant value itself as well as with MK/RK/AK values, indicating substantial anatomical variability of these discrepancies. In the HCP dataset, the median voxelwise percentage differences across the whole white matter skeleton were (nonlinear least squares algorithm) 14.5% (8.2%-23.1%) for MD, 4.3% (1.4%-17.3%) for FA, -5.2% (-48.7% to -0.8%) for MO, 12.5% (6.4%-21.2%) for RD, and 16.1% (9.9%-25.6%) for AD (all ranges computed as 0.01 and 0.99 quantiles). All differences/trends were consistent between the discovery (HCP) and replication (local) datasets and between estimation algorithms. However, the relationships between such trends, estimated diffusion tensor invariants, and kurtosis estimates were impacted by the choice of fitting routine. Model-dependent differences in the estimation of conventional indexes of MD/FA/MO/RD/AD can be well beyond commonly seen disease-related alterations. While estimating diffusion tensor-derived indexes using the DKI model may be advantageous in terms of mitigating b-value dependence of diffusivity estimates, such estimates should not be referred to as conventional DTI-derived indexes in order to avoid confusion in interpretation as well as multicenter comparisons. In order to assess the potential and advantages of DKI with respect to DTI as well as to standardize diffusion-weighted imaging methods between centers, both conventional DTI-derived indexes and diffusion tensor invariants derived by fitting the non-Gaussian DKI model should be separately estimated and analyzed using the same combination of fitting routines.

Real-time testing of titanium sheet and extrusion coupon specimens subjected to Mach 2.7 supersonic cruise aircraft wing stresses and temperatures

NASA Technical Reports Server (NTRS)

Lunde, T.

1977-01-01

The accuracy of three accelerated flight-by-flight test methods for material selection, and fatigue substantiation of supersonic cruise aircraft structure was studied. The real time stresses and temperatures applied to the specimens were representative of the service conditions in the lower surface of a Mach 2.7 supersonic cruise aircraft wing root structure. Each real time flight lasted about 65 minutes, including about one hour at (500 F) in the cruise condition. Center notched coupon specimens from six titanium materials were tested: mill-annealed, duplex-annealed, and triplex-annealed Ti-8Al-1Mo-1V sheets; mill-annealed Ti-8Al-1Mo-1V extrusion; mill-annealed Ti-6Al-4V sheet; and solution-treated and aged Ti-6Al-4V extrusion. For duplex-annealed Ti-8Al-1Mo-1V sheet, specimens with single spotweld were also tested. The test results were studied in conjunction with other related data from the literature for: material selection, structural fabrication, fatigue resistance of supersonic cruise aircraft structure, and fatigue test acceleration procedures for supersonic cruise aircraft.

Dietary Supplements Contribute Substantially to the Total Nutrient Intake in Pregnant Norwegian Women

PubMed Central

Haugen, Margaretha; Brantsæter, Anne Lise; Alexander, Jan; Meltzer, Helle Margrete

2008-01-01

Background Use of dietary supplements during pregnancy may give an important contribution to nutrient intake, and for nutrients like folate and vitamin D supplements are recommended. Our objective was to study use and contribution of dietary supplement to nutrient intake among women participating in the Norwegian Mother and Child Cohort Study (MoBa). Methods This study is based on 40,108 women participating in MoBa which is conducted by the Norwegian Institute of Public Health. The women had filled inversion 2 of the food frequency questionnaire in MoBa between February 2002 and February 2005. Results 81% reported use of one or more dietary supplements. The most commonly used category was cod liver oil/fish oil supplements (59%) followed by singular folic acid supplements (36%) and multivitamin/multimineral supplements (31%). The nutrient contribution of the dietary supplements varied from 65% for folate and vitamin D to 1% for potassium among supplement users. The dietary intake of vitamin D, folate, iodine and iron did not reach the Nordic Recommendations for pregnant women. Conclusions Use of supplements improved the intake of folate, iron and vitamin D, but not sufficiently to reach the recommended amounts. PMID:18645244

Effect of Infection Duration on Habitat Selection and Morphology of Adult Echinostoma caproni (Digenea: Echinostomatidae) in ICR Mice.

PubMed

Platt, Thomas R; Zelmer, Derek A

2016-02-01

The course of infection of Echinostoma caproni was followed in female ICR mice, a permissive laboratory host, from infection to natural termination. Twenty-one mice were infected with 20 metacercariae via oral intubation and housed 3 per cage. Three mice from a randomly selected cage were necropsied at 1 mo intervals. A second group of 15 mice was infected approximately 1 yr later to replace mice negative at necropsy in the first group. Mice in the second group were examined weekly for the presence of eggs in the feces. Mice negative for eggs on consecutive days were killed and necropsied. The location of individual worms and worm clusters were located in 20 segments of the small intestine. Adult worms were killed and fixed in hot formalin, stained, and prepared as whole mounts. Standard measurements were taken using a compound microscope fitted with an ocular micrometer. The infection spontaneously resolved in 10 mice from 7 to 32 wk PI, indicating the host response is highly variable and extending the maximum recorded length of E. caproni infections in ICR mice to 31 wk. A moribund worm was found in the feces of an animal that continued to pass eggs for an additional 2 mo indicating individual variation in worm responses. Worms located preferentially in the ileum (segments 11-13) during the first 3 mo of the infection but shifted to the jejunum (segments 8-9) during weeks 4-6. Morphologically, worms of different ages clustered together in multivariate space, with substantial overlap between the 3- and 4-mo-old infrapopulations and between the 5- and 6-mo-old infrapopulations. Muscular structures increased in size throughout the experiment, while the gonads increased in size for the first 3 mo and then declined during the last 3 mo. The relationship between E. caproni and ICR mice is more nuanced than previously reported. The reduction in gonad size and the shift from the ileum to the jejunum in the last 3 mo likely are related. These changes might be attributable to a localized immune response by mice to E. caproni that results in the ileum becoming less hospitable and a resultant relocation of the worms to a less favorable location in the jejunum.

Extended Fenske-Hall LCAO MO calculations of core-level shifts in solid P compounds

NASA Astrophysics Data System (ADS)

Franke, R.; Chassé, T.; Reinhold, J.; Streubel, P.; Szargan, R.

1997-08-01

Extended Fenske-Hall LCAO-MO ΔSCF calculations on solids modelled as H-pseudoatom saturated clusters are reported. The computational results verify the experimentally obtained initial-state (effective atomic charges, Madelung potential) and relaxation-energy contributions to the XPS phosphorus core-level binding energy shifts measured in Na 3PO 3S, Na 3PO 4, Na 2PO 3F and NH 4PF 6 in reference to red phosphorus. It is shown that the different initial-state contributions observed in the studied phosphates are determined by local and nonlocal terms while the relaxation-energy contributions are mainly dependent on the nature of the nearest neighbors of the phosphorus atom.

Metal oxide induced charge transfer doping and band alignment of graphene electrodes for efficient organic light emitting diodes.

PubMed

Meyer, Jens; Kidambi, Piran R; Bayer, Bernhard C; Weijtens, Christ; Kuhn, Anton; Centeno, Alba; Pesquera, Amaia; Zurutuza, Amaia; Robertson, John; Hofmann, Stephan

2014-06-20

The interface structure of graphene with thermally evaporated metal oxide layers, in particular molybdenum trioxide (MoO3), is studied combining photoemission spectroscopy, sheet resistance measurements and organic light emitting diode (OLED) characterization. Thin (<5 nm) MoO3 layers give rise to an 1.9 eV large interface dipole and a downwards bending of the MoO3 conduction band towards the Fermi level of graphene, leading to a near ideal alignment of the transport levels. The surface charge transfer manifests itself also as strong and stable p-type doping of the graphene layers, with the Fermi level downshifted by 0.25 eV and sheet resistance values consistently below 50 Ω/sq for few-layer graphene films. The combination of stable doping and highly efficient charge extraction/injection allows the demonstration of simplified graphene-based OLED device stacks with efficiencies exceeding those of standard ITO reference devices.

Tunable, Highly Stable Lasers for Coherent Lidar

NASA Technical Reports Server (NTRS)

Henderson, Sammy W.; Hale, Charley P.; EEpagnier, David M.

2006-01-01

Practical space-based coherent laser radar systems envisioned for global winds measurement must be very efficient and must contend with unique problems associated with the large platform velocities that the instruments experience in orbit. To compensate for these large platform-induced Doppler shifts in space-based applications, agile-frequency offset-locking of two single-frequency Doppler reference lasers was thoroughly investigated. Such techniques involve actively locking a frequency-agile master oscillator (MO) source to a comparatively static local oscillator (LO) laser, and effectively producing an offset between MO (the lidar slave oscillator seed source, typically) and heterodyne signal receiver LO that lowers the bandwidth of the receiver data-collection system and permits use of very high-quantum-efficiency, reasonably- low-bandwidth heterodyne photoreceiver detectors and circuits. Recent work on MO/LO offset locking has focused on increasing the offset locking range, improving the graded-InGaAs photoreceiver performance, and advancing the maturity of the offset locking electronics. A figure provides a schematic diagram of the offset-locking system.

MO-FG-204-08: Optimization-Based Image Reconstruction From Unevenly Distributed Sparse Projection Views

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xie, Huiqiao; Yang, Yi; Tang, Xiangyang

2015-06-15

Purpose: Optimization-based reconstruction has been proposed and investigated for reconstructing CT images from sparse views, as such the radiation dose can be substantially reduced while maintaining acceptable image quality. The investigation has so far focused on reconstruction from evenly distributed sparse views. Recognizing the clinical situations wherein only unevenly sparse views are available, e.g., image guided radiation therapy, CT perfusion and multi-cycle cardiovascular imaging, we investigate the performance of optimization-based image reconstruction from unevenly sparse projection views in this work. Methods: The investigation is carried out using the FORBILD and an anthropomorphic head phantoms. In the study, 82 views, whichmore » are evenly sorted out from a full (360°) axial CT scan consisting of 984 views, form sub-scan I. Another 82 views are sorted out in a similar manner to form sub-scan II. As such, a CT scan with sparse (164) views at 1:6 ratio are formed. By shifting the two sub-scans relatively in view angulation, a CT scan with unevenly distributed sparse (164) views at 1:6 ratio are formed. An optimization-based method is implemented to reconstruct images from the unevenly distributed views. By taking the FBP reconstruction from the full scan (984 views) as the reference, the root mean square (RMS) between the reference and the optimization-based reconstruction is used to evaluate the performance quantitatively. Results: In visual inspection, the optimization-based method outperforms the FBP substantially in the reconstruction from unevenly distributed, which are quantitatively verified by the RMS gauged globally and in ROIs in both the FORBILD and anthropomorphic head phantoms. The RMS increases with increasing severity in the uneven angular distribution, especially in the case of anthropomorphic head phantom. Conclusion: The optimization-based image reconstruction can save radiation dose up to 12-fold while providing acceptable image quality for advanced clinical applications wherein only unevenly distributed sparse views are available. Research Grants: W81XWH-12-1-0138 (DoD), Sinovision Technologies.« less

Analytical validation and reference intervals for freezing point depression osmometer measurements of urine osmolality in dogs.

PubMed

Guerrero, Samantha; Pastor, Josep; Tvarijonaviciute, Asta; Cerón, José Joaquín; Balestra, Graziano; Caldin, Marco

2017-11-01

Urine osmolality (UOsm) is considered the most accurate measure of urine concentration and is used to assess body fluid homeostasis and renal function. We performed analytical validation of freezing point depression measurement of canine UOsm, to establish reference intervals (RIs) and to determine the effect of age, sex, and reproductive status on UOsm in dogs. Clinically healthy dogs ( n = 1,991) were retrospectively selected and stratified in groups by age (young [0-12 mo], adults [13-84 mo], and seniors [>84 mo]), sex (females and males), and reproductive status (intact and neutered). RIs were calculated for each age group. Intra- and inter-assay coefficients of variation were <1% in all cases. Good linearity ( r 2 = 1, p < 0.001) and recovery (89-98%) were observed. The limit of detection and limit of quantification were zero. Urine specific gravity and UOsm had a highly significant positive correlation ( r = 0.96, p < 0.001) but had inconsistent agreement. The 95% RI for canine UOsm was 369-2,416 mOsm/kg in young and adult dogs, and 366-2,178 mOsm/kg in seniors. Senior dogs had a significantly lower UOsm than young and adult dogs ( p < 0.000). Neutered females had a significantly lower UOsm than intact female dogs ( p < 0.002). These results indicate that the method evaluated is adequate for UOsm measurement and that RIs based on age and reproductive status should be used in dogs.

United States Air Force Statistical Digest, Fiscal Year 1955. Tenth Edition

DTIC Science & Technology

1955-09-30

cceee to rest v1th the en - gine(s) stopped for normal deplaning, and vhf ch results in minor, substantial dam.age or des - truction of the ei rcr-ert...mentaswellas recommendation for new material for inclusion should be addressed to the Director of Statistical Services, Headquarters United States Air Force...Mo de L; , Fiscal Year 1955 . . . • • . . . • . . . . . . . . . . . . . . . . . 139 PARTV- AIRCRAFT -ENGINES Introduction and Definitions 1𔃻 Table 65

Achieving Ohmic Contact for High-quality MoS2 Devices on Hexagonal Boron Nitride

NASA Astrophysics Data System (ADS)

Cui, Xu

MoS2, among many other transition metal dichalcogenides (TMDCs), holds great promise for future applications in nano-electronics, opto-electronics and mechanical devices due to its ultra-thin nature, flexibility, sizable band-gap, and unique spin-valley coupled physics. However, there are two main challenges that hinder careful study of this material. Firstly, it is hard to achieve Ohmic contacts to mono-layer MoS2, particularly at low temperatures (T) and low carrier densities. Secondly, materials' low quality and impurities introduced during the fabrication significantly limit the electron mobility of mono- and few-layer MoS2 to be substantially below theoretically predicted limits, which has hampered efforts to observe its novel quantum transport behaviours. Traditional low work function metals doesn't necessary provide good electron injection to thin MoS2 due to metal oxidation, Fermi level pinning, etc. To address the first challenge, we tried multiple contact schemes and found that mono-layer hexagonal boron nitride (h-BN) and cobalt (Co) provide robust Ohmic contact. The mono-layer spacer serves two advantageous purposes: it strongly interacts with the transition metal, reducing its work function by over 1 eV; and breaks the metal-TMDCs interaction to eliminate the interfacial states that cause Fermi level pinning. We measure a flat-band Schottky barrier of 16 meV, which makes thin tunnel barriers upon doping the channels, and thus achieve low-T contact resistance of 3 kohm.um at a carrier density of 5.3x10. 12/cm. 2. Similar to graphene, eliminating all potential sources of disorder and scattering is the key to achieving high performance in MoS2 devices. We developed a van der Waals heterostructure device platform where MoS2 layers are fully encapsulated within h-BN and electrically contacted in a multi-terminal geometry using gate-tunable graphene electrodes. The h-BN-encapsulation provides excellent protection from environmental factors, resulting in highly stable device performance, even at elevated temperatures. Both optical and electrical characterization confirms our high quality devices, including an ultra-clean interface, a record-high Hall mobility reaching 34,000 cm. 2/Vs, and first observation of Shubnikov–de Haas oscillations. The development of Ohmic contact and fabrication of high quality devices are critical to MoS2 application and studying its intrinsic properties. Therefore, the progress made in this work will facilitate efforts to study novel physical phenomena of MoS2 that were not accessible before.

IRRADIATION PERFORMANCE OF U-Mo MONOLITHIC FUEL

DOE Office of Scientific and Technical Information (OSTI.GOV)

M.K. Meyer; J. Gan; J.-F. Jue

2014-04-01

High-performance research reactors require fuel that operates at high specific power to high fission density, but at relatively low temperatures. Research reactor fuels are designed for efficient heat rejection, and are composed of assemblies of thin-plates clad in aluminum alloy. The development of low-enriched fuels to replace high-enriched fuels for these reactors requires a substantially increased uranium density in the fuel to offset the decrease in enrichment. Very few fuel phases have been identified that have the required combination of very-high uranium density and stable fuel behavior at high burnup. UMo alloys represent the best known tradeoff in these properties.more » Testing of aluminum matrix U-Mo aluminum matrix dispersion fuel revealed a pattern of breakaway swelling behavior at intermediate burnup, related to the formation of a molybdenum stabilized high aluminum intermetallic phase that forms during irradiation. In the case of monolithic fuel, this issue was addressed by eliminating, as much as possible, the interfacial area between U-Mo and aluminum. Based on scoping irradiation test data, a fuel plate system composed of solid U-10Mo fuel meat, a zirconium diffusion barrier, and Al6061 cladding was selected for development. Developmental testing of this fuel system indicates that it meets core criteria for fuel qualification, including stable and predictable swelling behavior, mechanical integrity to high burnup, and geometric stability. In addition, the fuel exhibits robust behavior during power-cooling mismatch events under irradiation at high power.« less

Alkali/TX[sub 2] catalysts for CO/H[sub 2] conversion to C[sub 1]-C[sub 4] alcohols

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klier, K.; Herman, R.G.; Richards-Babb, M.

1993-03-01

The objective of this research is to determine the patterns of variations of catalyst activity and selectivity for the synthesis of alcohols from H[sub 2]/CO synthesis gas. Since the source of carbon can be coal-derived synthesis gas, this research makes a contribution to the technology for high quality clean transportation fuels and for basic chemicals from coal. Catalysts prepared were principally based on MoS[sub 2], RuS[sub 2], TaS[sub 2], and NbS[sub 2]. Catalytic testing of these materials was carried out both before and after surface doping with Cs. In alcohol synthesis activation of hydrogen by the catalyst surface is essential.more » Knowledge of transition metal disulfide surface properties is important before the mechanism of hydrogen dissociation can be addressed. The electronic structures of MoS[sub 2], RuS[sub 2], and NbS[sub 2] were studied both theoretically and experimentally. Experimental valence bands were obtained by high resolution electron spectroscopy for chemical analysis (HR-ESCA, also referred to as x-ray photoelectron spectroscopy) and theoretical valence bands were calculated using solid state extended Hueckel theory. Comparison of two-dimensional (2-D) MoS[sub 2] theoretical valence bands with the experimental HR-ESCA valence bands of polycrystalline MoS[sub 2] led to parametrization of the S 3s, S 3p, and Mo 4d atomic ionization potentials and Slater-type coefficients and exponents. The S 3s and S 3p parameters obtained for MoS[sub 2] were used to obtain the NbS[sub 2] and RuS[sub 2] theoretical valence bands.« less

Alkali/TX{sub 2} catalysts for CO/H{sub 2} conversion to C{sub 1}-C{sub 4} alcohols. Final technical progress report, September 1, 1988--August 31, 1991

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klier, K.; Herman, R.G.; Richards-Babb, M.

1993-03-01

The objective of this research is to determine the patterns of variations of catalyst activity and selectivity for the synthesis of alcohols from H{sub 2}/CO synthesis gas. Since the source of carbon can be coal-derived synthesis gas, this research makes a contribution to the technology for high quality clean transportation fuels and for basic chemicals from coal. Catalysts prepared were principally based on MoS{sub 2}, RuS{sub 2}, TaS{sub 2}, and NbS{sub 2}. Catalytic testing of these materials was carried out both before and after surface doping with Cs. In alcohol synthesis activation of hydrogen by the catalyst surface is essential.more » Knowledge of transition metal disulfide surface properties is important before the mechanism of hydrogen dissociation can be addressed. The electronic structures of MoS{sub 2}, RuS{sub 2}, and NbS{sub 2} were studied both theoretically and experimentally. Experimental valence bands were obtained by high resolution electron spectroscopy for chemical analysis (HR-ESCA, also referred to as x-ray photoelectron spectroscopy) and theoretical valence bands were calculated using solid state extended Hueckel theory. Comparison of two-dimensional (2-D) MoS{sub 2} theoretical valence bands with the experimental HR-ESCA valence bands of polycrystalline MoS{sub 2} led to parametrization of the S 3s, S 3p, and Mo 4d atomic ionization potentials and Slater-type coefficients and exponents. The S 3s and S 3p parameters obtained for MoS{sub 2} were used to obtain the NbS{sub 2} and RuS{sub 2} theoretical valence bands.« less

Monte Carlo Simulation of X-Ray Spectra in Mammography and Contrast-Enhanced Digital Mammography Using the Code PENELOPE

NASA Astrophysics Data System (ADS)

Cunha, Diego M.; Tomal, Alessandra; Poletti, Martin E.

2013-04-01

In this work, the Monte Carlo (MC) code PENELOPE was employed for simulation of x-ray spectra in mammography and contrast-enhanced digital mammography (CEDM). Spectra for Mo, Rh and W anodes were obtained for tube potentials between 24-36 kV, for mammography, and between 45-49 kV, for CEDM. The spectra obtained from the simulations were analytically filtered to correspond to the anode/filter combinations usually employed in each technique (Mo/Mo, Rh/Rh and W/Rh for mammography and Mo/Cu, Rh/Cu and W/Cu for CEDM). For the Mo/Mo combination, the simulated spectra were compared with those obtained experimentally, and for spectra for the W anode, with experimental data from the literature, through comparison of distribution shape, average energies, half-value layers (HVL) and transmission curves. For all combinations evaluated, the simulated spectra were also compared with those provided by different models from the literature. Results showed that the code PENELOPE provides mammographic x-ray spectra in good agreement with those experimentally measured and those from the literature. The differences in the values of HVL ranged between 2-7%, for anode/filter combinations and tube potentials employed in mammography, and they were less than 5% for those employed in CEDM. The transmission curves for the spectra obtained also showed good agreement compared to those computed from reference spectra, with average relative differences less than 12% for mammography and CEDM. These results show that the code PENELOPE can be a useful tool to generate x-ray spectra for studies in mammography and CEDM, and also for evaluation of new x-ray tube designs and new anode materials.

Functional analysis of aldehyde oxidase using expressed chimeric enzyme between monkey and rat.

PubMed

Itoh, Kunio; Asakawa, Tasuku; Hoshino, Kouichi; Adachi, Mayuko; Fukiya, Kensuke; Watanabe, Nobuaki; Tanaka, Yorihisa

2009-01-01

Aldehyde oxidase (AO) is a homodimer with a subunit molecular mass of approximately 150 kDa. Each subunit consists of about 20 kDa 2Fe-2S cluster domain storing reducing equivalents, about 40 kDa flavine adenine dinucleotide (FAD) domain and about 85 kDa molybdenum cofactor (MoCo) domain containing a substrate binding site. In order to clarify the properties of each domain, especially substrate binding domain, chimeric cDNAs were constructed by mutual exchange of 2Fe-2S/FAD and MoCo domains between monkey and rat. Chimeric monkey/rat AO was referred to one with monkey type 2Fe-2S/FAD domains and a rat type MoCo domain. Rat/monkey AO was vice versa. AO-catalyzed 2-oxidation activities of (S)-RS-8359 were measured using the expressed enzyme in Escherichia coli. Substrate inhibition was seen in rat AO and chimeric monkey/rat AO, but not in monkey AO and chimeric rat/monkey AO, suggesting that the phenomenon might be dependent on the natures of MoCo domain of rat. A biphasic Eadie-Hofstee profile was observed in monkey AO and chimeric rat/monkey AO, but not rat AO and chimeric monkey/rat AO, indicating that the biphasic profile might be related to the properties of MoCo domain of monkey. Two-fold greater V(max) values were observed in monkey AO than in chimeric rat/monkey AO, and in chimeric monkey/rat AO than in rat AO, suggesting that monkey has the more effective electron transfer system than rat. Thus, the use of chimeric enzymes revealed that 2Fe-2S/FAD and MoCo domains affect the velocity and the quantitative profiles of AO-catalyzed (S)-RS-8359 2-oxidation, respectively.

Neurodevelopmental and mental health comorbidities in children and adolescents with epilepsy and migraine: a response to identified research gaps.

PubMed

Wagner, Janelle L; Wilson, Dulaney A; Smith, Gigi; Malek, Angela; Selassie, Anbesaw W

2015-01-01

To determine the distribution and risk characteristics of comorbid neurodevelopmental and mental health comorbidities among children and adolescents (6-18y) with epilepsy or migraine (i.e. a neurological condition with shared features and potential etiology) compared with lower extremity fracture (LEF). This case-control study involved a subset analysis of surveillance data in South Carolina, USA. Hospital admission, outpatient, and emergency department visits for individuals with an International Classification of Disease, 9th revision Clinical Modification diagnosis of epilepsy (n=6730; 54.5% females, 45.5% males; mean age [SD] 14y 2mo [4y 5mo]); migraine (n=10 495; 74.5% females, 25.5% males; 15y 6mo [2y 6mo]), or LEF (n=15 305; 40.3% females, 59.7% males; 13y 11mo [2y 11mo]) from January 1 2000 to December 31 2011 were identified. The association of epilepsy, migraine, or LEF with any mental health comorbidity was evaluated with univariate and multivariate polytomous logistic regression. Comorbidities were highly prevalent in children and adolescents, with epilepsy with a rate of 29.7% (95% confidence interval [CI]: 28.6-30.8) for mental health comorbidities and 30.8% (95% CI: 29.7-31.9) for neurodevelopmental comorbidities. The odds of mental health comorbidity was 2.20 (95% CI: 2.02-2.39) for children and adolescents with epilepsy and 1.60 (95% CI: 1.48-1.73) for migraine, in reference to children and adolescents with LEF after adjusting for potential confounders. Prevalence and risk for specific comorbidities are presented. Neuropathophysiological and psychosocial factors specific to epilepsy may provide more risk for adolescents with epilepsy compared to migraine. © 2014 Mac Keith Press.

Effects of Bi doping on structural and magnetic properties of double perovskite oxides Sr2FeMoO6

NASA Astrophysics Data System (ADS)

Lan, Yaohai; Feng, Xiaomei; Zhang, Xin; Shen, Yifu; Wang, Ding

2016-08-01

A new series of double perovskite compounds Sr2 - δBixFeMoO6 have been synthesized by solid-state reaction. δ refers to the nominal doping content of Bi (δ = 0, 0.1, 0.2, 0.3, 0.4, 0.5), while the Bi content obtained by the Rietveld refinement is x = 0, 0.01, 0.05, 0.08, 0.10 and 0.12. Their crystal structure and magnetic properties are investigated. Rietveld analysis of the room temperature XRD data shows all the samples crystallize in the cubic crystal structure with the space group Fm 3 ‾ m and have no phase transition. SEM images show that substituted samples present a denser microstructure and bigger grains than Sr2FeMoO6, which is caused by a liquid sintering process due to the effumability of Bi. The unit cell volume increases with augment of Bi3+ concentration despite the smaller ionic radius Bi3+ compared with the Sr2+, which is attributed to the electronic effect. The degree of Fe/Mo order (η) increases first and then decreases to almost disappearance with augment of Bi doping, which is the result of contribution from electronic effect. Calculated saturation magnetization Ms(3) according to our phase separation likeness model matches well with the experimental ones. The observed variations of magnetoresistance (MR) are consistent with the Fe/Mo order (η) due to the internal connection with anti-site defect (ASD).

Theoretical study of thermoelectric properties of few-layer MoS2 and WSe2.

PubMed

Huang, Wen; Luo, Xin; Gan, Chee Kwan; Quek, Su Ying; Liang, Gengchiau

2014-06-14

Molybdenum disulfide (MoS2) and tungsten diselenide (WSe2) are prototypical layered two-dimensional transition metal dichalcogenide materials, with each layer consisting of three atomic planes. We refer to each layer as a trilayer (TL). We study the thermoelectric properties of 1-4TL MoS2 and WSe2 using a ballistic transport approach based on the electronic band structures and phonon dispersions obtained from first-principles calculations. Our results show that the thickness dependence of the thermoelectric properties is different under n-type and p-type doping conditions. Defining ZT1st peak as the first peak in the thermoelectric figure of merit ZT as doping levels increase from zero at 300 K, we found that ZT1st peak decreases as the number of layers increases for MoS2, with the exception of 2TL in n-type doping, which has a slightly higher value than 1TL. However, for WSe2, 2TL has the largest ZT1st peak in both n-type and p-type doping, with a ZT1st peak value larger than 1 for n-type WSe2. At high temperatures (T > 300 K), ZT1st peak dramatically increases when the temperature increases, especially for n-type doping. The ZT1st peak of n-type 1TL-MoS2 and 2TL-WSe2 can reach 1.6 and 2.1, respectively.

78 FR 29292 - Partial Approval and Partial Disapproval of Air Quality State Implementation Plans; Arizona...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-20

... Technology (BART) controls for four sources. These sources are Freeport-McMoRan Incorporated (FMMI) Miami... Electric Power Cooperative (AEPCO) Apache Generating Station. However, we are proposing to disapprove other...) The initials BART mean or refer to Best Available Retrofit Technology. (5) The term Class I area...

MENTOR: an enabler for interoperable intelligent systems

NASA Astrophysics Data System (ADS)

Sarraipa, João; Jardim-Goncalves, Ricardo; Steiger-Garcao, Adolfo

2010-07-01

A community with knowledge organisation based on ontologies will enable an increase in the computational intelligence of its information systems. However, due to the worldwide diversity of communities, a high number of knowledge representation elements, which are not semantically coincident, have appeared representing the same segment of reality, becoming a barrier to business communications. Even if a domain community uses the same kind of technologies in its information systems, such as ontologies, it doesn't solve its semantics differences. In order to solve this interoperability problem, a solution is to use a reference ontology as an intermediary in the communications between the community enterprises and the outside, while allowing the enterprises to keep their own ontology and semantics unchanged internally. This work proposes MENTOR, a methodology to support the development of a common reference ontology for a group of organisations sharing the same business domain. This methodology is based on the mediator ontology (MO) concept, which assists the semantic transformations among each enterprise's ontology and the referential one. The MO enables each organisation to keep its own terminology, glossary and ontological structures, while providing seamless communication and interaction with the others.

Process for producing dispersed particulate composite materials

DOEpatents

Henager, Jr., Charles H.; Hirth, John P.

1995-01-01

This invention is directed to a process for forming noninterwoven dispersed particulate composite products. In one case a composite multi-layer film product comprises a substantially noninterwoven multi-layer film having a plurality of discrete layers. This noninterwoven film comprises at least one discrete layer of a first material and at least one discrete layer of a second material. In another case the first and second materials are blended together with each other. In either case, the first material comprises a metalloid and the second material a metal compound. At least one component of a first material in one discrete layer undergoes a solid state displacement reaction with at least one component of a second material thereby producing the requisite noninterwoven composite film product. Preferably, the first material comprises silicon, the second material comprises Mo.sub.2 C, the third material comprises SiC and the fourth material comprises MoSi.sub.2.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abugideiri, F.; Kelland, M.A.; Poli, R.

Cp*MoH[sub 5](PMe[sub 3]) has been prepared from Cp*MoCl[sub 2](PMe[sub 3]) and LiAlH[sub 4]. The compound is analogous to the previously reported Cp*WH[sub 5](PMe[sub 3]) and CpWH[sub 5](PMe[sub 3]) (Green, M.L.H.; Parkin, G.J. Chem. Soc., Chem. Commun. 1984, 1467. Schrock, R. R.; et al. Organometallics 1986, 5, 1681) for which structural assignments were not made. A single sharp [sup 1]H-NMR resonance is observed for the five hydrides down to 183 K, consistent with either a static symmetric structure or a highly fluxional structure, either classical or nonclassical. The measured minimum longtudinal relaxation time, T[sub 1], is quite long (780 ms atmore » 400 MHz and 230 K) and consistent with a classical structure based on the pentagonal bipyramid which gives rise to a substantially anisotropic moment of inertia. 14 refs., 1 tab.« less

Human monocyte-derived suppressor cells control graft-versus-host disease by inducing regulatory forkhead box protein 3-positive CD8+ T lymphocytes.

PubMed

Janikashvili, Nona; Trad, Malika; Gautheron, Alexandrine; Samson, Maxime; Lamarthée, Baptiste; Bonnefoy, Francis; Lemaire-Ewing, Stéphanie; Ciudad, Marion; Rekhviashvili, Khatuna; Seaphanh, Famky; Gaugler, Béatrice; Perruche, Sylvain; Bateman, Andrew; Martin, Laurent; Audia, Sylvain; Saas, Philippe; Larmonier, Nicolas; Bonnotte, Bernard

2015-06-01

Adoptive transfer of immunosuppressive cells has emerged as a promising strategy for the treatment of immune-mediated disorders. However, only a limited number of such cells can be isolated from in vivo specimens. Therefore efficient ex vivo differentiation and expansion procedures are critically needed to produce a clinically relevant amount of these suppressive cells. We sought to develop a novel, clinically relevant, and feasible approach to generate ex vivo a subpopulation of human suppressor cells of monocytic origin, referred to as human monocyte-derived suppressive cells (HuMoSCs), which can be used as an efficient therapeutic tool to treat inflammatory disorders. HuMoSCs were generated from human monocytes cultured for 7 days with GM-CSF and IL-6. The immune-regulatory properties of HuMoSCs were investigated in vitro and in vivo. The therapeutic efficacy of HuMoSCs was evaluated by using a graft-versus-host disease (GvHD) model of humanized mice (NOD/SCID/IL-2Rγc(-/-) [NSG] mice). CD33+ HuMoSCs are highly potent at inhibiting the proliferation and activation of autologous and allogeneic effector T lymphocytes in vitro and in vivo. The suppressive activity of these cells depends on signal transducer and activator of transcription 3 activation. Of therapeutic relevance, HuMoSCs induce long-lasting memory forkhead box protein 3-positive CD8+ regulatory T lymphocytes and significantly reduce GvHD induced with human PBMCs in NSG mice. Ex vivo-generated HuMoSCs inhibit effector T lymphocytes, promote the expansion of immunosuppressive forkhead box protein 3-positive CD8+ regulatory T cells, and can be used as an efficient therapeutic tool to prevent GvHD. Copyright © 2015 American Academy of Allergy, Asthma & Immunology. Published by Elsevier Inc. All rights reserved.

Effects of alloying on aging and hardening processes of steel with 20% nickel

NASA Technical Reports Server (NTRS)

Bogachev, I. N.; Zvigintsev, N. V.; Maslakova, T. M.

1981-01-01

Measurements of hardness, thermal emf, and electrical resistance were used to study the effects of Co, Mo, Ti and Al contents on aging and hardening processes in Fe 20%Ni steel. It is shown that the effects of these alloying elements differ substantially. Anomalies which arise in the temperature dependence of physical properties due to the presence of cobalt and molybdenum are reduced by the inclusion of titanium and aluminum (and vice versa).

Coffee, tea, caffeine, and risk of breast cancer: a twenty two-year follow-up

PubMed Central

Ganmaa, Davaasambuu; Willett, Walter C.; Li, Tricia Y.; Feskanich, Diane; van Dam, Rob M.; Lopez-Garcia, Esther; Hunter, David J.; Holmes, Michelle D.

2014-01-01

The relation between consumption of coffee, tea, and caffeine and risk of breast cancer remains unsettled. We examined data from a large, long-term cohort study to evaluate whether high intake of coffee and caffeine is associated with increased risk of breast cancer. This was a prospective cohort study with 85,987 female participants in the Nurses’ Health Study. Consumption of coffee, tea and caffeine consumption was assessed in 1980, 1984, 1986, 1990, 1994, 1998, and the follow-up continued through 2002. We documented 5,272 cases of invasive breast cancer during 1,715,230 person-years. The multivariate relative risks (RRs) of breast cancer across categories of caffeinated coffee consumption were: 1.0 for <1cup/mo (reference category), 1.01 (95% confidence interval: 0.92–1.12) for 1/mo-4.9/wk, 0.92 (0.84–1.01) for 5/wk-1.9/d, 0.93 (0.85–1.02) for 2–3.9/d, 0.92 (0.82–1.03) for ≥4 cups per day (p for trend= 0.14). Intakes of tea and decaffeinated coffee were also not significantly associated with risk of breast cancer. RRs (95% CI) for increasing quintiles of caffeine intake were 1.00, 0.98 (0.90–1.07), 0.92 (0.84–1.00), 0.94 (0.87–1.03), and 0.93 (0.85–1.01) (p for trend=0.06). A significant inverse association of caffeine intake with breast cancers was observed among postmenopausal women; for the highest quintile of intake compared to the lowest RR 0.88 (95% CI = 0.79 to 0.97, p for trend=0.03). We observed no substantial association between caffeinated and decaffeinated coffee and tea consumption and risk of breast cancer in the overall cohort. However, our results suggested a weak inverse association between caffeine-containing beverages and risk of postmenopausal breast cancer. PMID:18183588

Effect of Niobium on Phase Transformations, Mechanical Properties and Corrosion of Supermartensitic Stainless Steel

NASA Astrophysics Data System (ADS)

de Oliveira, Mariana Perez; Calderón-Hernández, José Wilmar; Magnabosco, Rodrigo; Hincapie-Ladino, Duberney; Alonso-Falleiros, Neusa

2017-04-01

The influence of niobium addition in a supermartensitic stainless steel with 13Cr-5Ni-2Mo has been studied. The steel with Nb tempered at 600 °C for 2 h showed improved mechanical resistance properties and lower degree of sensitization, without compromising elongation and pitting corrosion resistance, when compared to the reference steel. In order to understand the Nb effect in such steel, mainly regarding phase transformation, different tempering time intervals have been studied. The better performance of the SM2MoNb is attributed to the hindering effect that Nb has in the kinetics of the phase transformations during tempering, delaying the precipitation start and coarsening stages of the present phases.

Bariatric Surgery in the United Kingdom: A Cohort Study of Weight Loss and Clinical Outcomes in Routine Clinical Care

PubMed Central

Douglas, Ian J.; Bhaskaran, Krishnan; Batterham, Rachel L.; Smeeth, Liam

2015-01-01

Background Bariatric surgery is becoming a more widespread treatment for obesity. Comprehensive evidence of the long-term effects of contemporary surgery on a broad range of clinical outcomes in large populations treated in routine clinical practice is lacking. The objective of this study was to measure the association between bariatric surgery, weight, body mass index, and obesity-related co-morbidities. Methods and Findings This was an observational retrospective cohort study using data from the United Kingdom Clinical Practice Research Datalink. All 3,882 patients registered in the database and with bariatric surgery on or before 31 December 2014 were included and matched by propensity score to 3,882 obese patients without surgery. The main outcome measures were change in weight and body mass index over 4 y; incident diagnoses of type 2 diabetes mellitus (T2DM), hypertension, angina, myocardial infarction (MI), stroke, fractures, obstructive sleep apnoea, and cancer; mortality; and resolution of hypertension and T2DM. Weight measures were available for 3,847 patients between 1 and 4 mo, 2,884 patients between 5 and 12 mo, and 2,258 patients between 13 and 48 mo post-procedure. Bariatric surgery patients exhibited rapid weight loss for the first four postoperative months, at a rate of 4.98 kg/mo (95% CI 4.88–5.08). Slower weight loss was sustained to the end of 4 y. Gastric bypass (6.56 kg/mo) and sleeve gastrectomy (6.29 kg/mo) were associated with greater initial weight reduction than gastric banding (2.77 kg/mo). Protective hazard ratios (HRs) were detected for bariatric surgery for incident T2DM, 0.68 (95% CI 0.55–0.83); hypertension, 0.35 (95% CI 0.27–0.45); angina, 0.59 (95% CI 0.40–0.87);MI, 0.28 (95% CI 0.10–0.74); and obstructive sleep apnoea, 0.55 (95% CI 0.40–0.87). Strong associations were found between bariatric surgery and the resolution of T2DM, with a HR of 9.29 (95% CI 6.84–12.62), and between bariatric surgery and the resolution of hypertension, with a HR of 5.64 (95% CI 2.65–11.99). No association was detected between bariatric surgery and fractures, cancer, or stroke. Effect estimates for mortality found no protective association with bariatric surgery overall, with a HR of 0.97 (95% CI 0.66–1.43). The data used were recorded for the management of patients in primary care and may be subject to inaccuracy, which would tend to lead to underestimates of true relative effect sizes. Conclusions Bariatric surgery as delivered in the UK healthcare system is associated with dramatic weight loss, sustained at least 4 y after surgery. This weight loss is accompanied by substantial improvements in pre-existing T2DM and hypertension, as well as a reduced risk of incident T2DM, hypertension, angina, MI, and obstructive sleep apnoea. Widening the availability of bariatric surgery could lead to substantial health benefits for many people who are morbidly obese. PMID:26694640

High performance perpendicular magnetic tunnel junction with Co/Ir interfacial anisotropy for embedded and standalone STT-MRAM applications

NASA Astrophysics Data System (ADS)

Huai, Yiming; Gan, Huadong; Wang, Zihui; Xu, Pengfa; Hao, Xiaojie; Yen, Bing K.; Malmhall, Roger; Pakala, Nirav; Wang, Cory; Zhang, Jing; Zhou, Yuchen; Jung, Dongha; Satoh, Kimihiro; Wang, Rongjun; Xue, Lin; Pakala, Mahendra

2018-02-01

High volume spin transfer torque magnetoresistance random access memory (STT-MRAM) for standalone and embedded applications requires a thin perpendicular magnetic tunnel junction (pMTJ) stack (˜10 nm) with a tunnel magnetoresistance (TMR) ratio over 200% after high temperature back-end-of-line (BEOL) processing up to 400 °C. A thin reference layer with low magnetic moment and strong perpendicular magnetic anisotropy (PMA) is key to reduce the total thickness of the full pMTJ stack. We demonstrated strong interfacial PMA and a perpendicular Ruderman-Kittel-Kasuya-Yosida exchange interaction in the Co/Ir system. Owing to the additional high PMA at the Ir/Co interface in combination with a conventional CoFeB/MgO interface in the Ir/Co/Mo/CoFeB/MgO reference layer, the full film pMTJ showed a TMR ratio over 210% after annealing at 400 °C for 150 min. The high TMR ratio can be attributed to the thin stack design by combining a thin reference layer with the efficient compensation by a thin pinned layer. The annealing stability may be explained by the absence of solid solution in the Co-Ir system and the low oxygen affinity of Mo in the reference layer and the free layer. High device performance with a TMR ratio over 210% was also confirmed after subjecting the patterned devices to BEOL processing temperatures of up to 400 °C. This proposed pMTJ design is suitable for both standalone and embedded STT-MRAM applications.

Behavior and Learning Difficulties in Children of Normal Intelligence Born to Alcoholic Mothers.

ERIC Educational Resources Information Center

Shaywitz, Sally E.; And Others

1980-01-01

Children referred to the Learning Disorders Unit of the Yale-New Haven Hospital were evaluated for indications of prenatal exposure to ethanol. Our results suggest a continuum of teratogenic effects of ethanol on the central nervous system. Journal availability The C. V. Mosby Co., 11830 Westline Industrial Dr., St. Louis, MO 63141. (Author)

Snapshot of an integrated psychosocial gastroenterology service.

PubMed

Kinsinger, Sarah W; Ballou, Sarah; Keefer, Laurie

2015-02-14

To characterize the patients utilizing a gastroenterology behavioral medicine service and examine the effect of treatment on health care utilization. Patients were referred by their gastroenterologists for psychological treatment during a 15 mo period. Patients seen for an intake with a psychologist completed the Brief Symptom Inventory (BSI) and a checklist of psychosocial concerns. A subset of patients with functional bowel disorders also completed a disease specific quality of life measure. Chart review was conducted to obtain information on type and frequency of sessions with the psychologist, the number of outpatient gastroenterology visits, and number of gastroenterology-related medical procedures during the 6 mo following psychological intake. Of 259 patients referred for treatment, 118 (46%) completed an intake with a psychologist. Diagnoses included: irritable bowel syndrome (42%), functional dyspepsia (20%), inflammatory bowel diseases (20%), esophageal symptoms (10%), and "other" (8%). Demographic variables and disease type did not differentiate between those who did and did not schedule an intake. Mean t-scores for the BSI global score index and the depression, anxiety, and somatization subscales fell below the cutoff for clinical significance (t = 63). Treatments were predominantly gut-directed hypnosis (48%) and cognitive behavioral therapy (44%). Average length of treatment was 4 sessions. Among functional gastrointestinal (GI) patients, those patients who initiated treatment received significantly fewer GI-related medical procedures during the 6 mo following the referral than patients who did not schedule an intake [t (197) = 2.69, P < 0.01]. Patients are receptive to psychological interventions for GI conditions and there is preliminary evidence that treatment can decrease health-care utilization among patients with functional GI conditions.

Investigation of the normal spectral band emissivity characteristic within 7.5 to 13 μm for Molybdenum between 100 and 500 °C

NASA Astrophysics Data System (ADS)

Zhang, Yan; Zhang, Yuzhong; Lu, Rongsheng; Shu, Shuangbao; Lang, Xianli; Yang, Lei

2018-01-01

Molybdenum (Mo) is an important material to construct the first wall for the Experimental Advanced Superconducting Tokamak (EAST). The real-time monitoring of temperature distribution of the first wall based on radiation thermometry is essential to guarantee the stable operation of EAST. So, it is especially important for the acquisition of emissivity property of Mo. In this work, a self-designed emissivity measurement apparatus is developed, and the relationship between the normal infrared spectral band (7.5-13 μm) emissivity of Mo against the temperature and surface roughness of material samples is experimentally investigated under the vacuum condition over the temperature ranging from 100 °C to 500 °C. Moreover, the dependence of spectral band emissivity of Mo exposed to air on the heating-duration time at a given elevated temperature is also studied. The emissivity measurement apparatus is mainly composed of a high temperature furnace and a radiation thermometer as well as a benchmark blackbody furnace. The radiation thermometer is firstly calibrated against the blackbody furnace by means of the multi-temperature methods. And then the temperature of the sample is simultaneously measured by the two highly accurate S-type thermocouples and the radiation thermometer. Finally the emissivity value of the sample is calculated based on the direct radiometric method. The developed emissivity measurement method and experimental results obtained in this work may be helpful to understand the work state the EAST and to use of Mo as an emissivity reference.

Inductively coupled plasma mass spectrometry for stable isotope metabolic tracer studies of living systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Luong, Elise

1999-05-10

This dissertation focuses on the development of methods for stable isotope metabolic tracer studies in living systems using inductively coupled plasma single and dual quadrupole mass spectrometers. Sub-nanogram per gram levels of molybdenum (Mo) from human blood plasma are isolated by the use of anion exchange alumina microcolumns. Million-fold more concentrated spectral and matrix interferences such as sodium, chloride, sulfate, phosphate, etc. in the blood constituents are removed from the analyte. The recovery of Mo from the alumina column is 82 ± 5% (n = 5). Isotope dilution inductively coupled plasma mass spectrometry (ID-ICP-MS) is utilized for the quantitative ultra-tracemore » concentration determination of Mo in bovine and human blood samples. The average Mo concentration in reference bovine serum determined by this method is 10.2 ± 0.4 ng/g, while the certified value is 11.5 ± 1.1 ng/g (95% confidence interval). The Mo concentration of one pool of human blood plasma from two healthy male donors is 0.5 ± 0.1 ng/g. The inductively coupled plasma twin quadrupole mass spectrometer (ICP-TQMS) is used to measure the carbon isotope ratio from non-volatile organic compounds and bio-organic molecules to assess the ability as an alternative analytical method to gas chromatography combustion isotope ratio mass spectrometry (GC-combustion-IRMS). Trytophan, myoglobin, and β-cyclodextrin are chosen for the study, initial observation of spectral interference of 13C + with 12C 1H + comes from the incomplete dissociation of myoglobin and/or β-cyclodextrin.« less

The Effect of Common Inversion Polymorphisms In(2L)t and In(3R)Mo on Patterns of Transcriptional Variation in Drosophila melanogaster.

PubMed

Lavington, Erik; Kern, Andrew D

2017-11-06

Chromosomal inversions are a ubiquitous feature of genetic variation. Theoretical models describe several mechanisms by which inversions can drive adaptation and be maintained as polymorphisms. While inversions have been shown previously to be under selection, or contain genetic variation under selection, the specific phenotypic consequences of inversions leading to their maintenance remain unclear. Here we use genomic sequence and expression data from the Drosophila Genetic Reference Panel (DGRP) to explore the effects of two cosmopolitan inversions, In ( 2L ) t and In ( 3R ) Mo , on patterns of transcriptional variation. We demonstrate that each inversion has a significant effect on transcript abundance for hundreds of genes across the genome. Inversion-affected loci (IAL) appear both within inversions as well as on unlinked chromosomes. Importantly, IAL do not appear to be influenced by the previously reported genome-wide expression correlation structure. We found that five genes involved with sterol uptake, four of which are Niemann-Pick Type 2 orthologs, are upregulated in flies with In ( 3R ) Mo but do not have SNPs in linkage disequilibrium (LD) with the inversion. We speculate that this upregulation is driven by genetic variation in mod ( mdg4 ) that is in LD with In ( 3R ) Mo We find that there is little evidence for a regional or position effect of inversions on gene expression at the chromosomal level, but do find evidence for the distal breakpoint of In ( 3R ) Mo interrupting one gene and possibly disassociating the two flanking genes from regulatory elements. Copyright © 2017 Lavington and Kern.

The Effect of Common Inversion Polymorphisms In(2L)t and In(3R)Mo on Patterns of Transcriptional Variation in Drosophila melanogaster

PubMed Central

Lavington, Erik; Kern, Andrew D.

2017-01-01

Chromosomal inversions are a ubiquitous feature of genetic variation. Theoretical models describe several mechanisms by which inversions can drive adaptation and be maintained as polymorphisms. While inversions have been shown previously to be under selection, or contain genetic variation under selection, the specific phenotypic consequences of inversions leading to their maintenance remain unclear. Here we use genomic sequence and expression data from the Drosophila Genetic Reference Panel (DGRP) to explore the effects of two cosmopolitan inversions, In(2L)t and In(3R)Mo, on patterns of transcriptional variation. We demonstrate that each inversion has a significant effect on transcript abundance for hundreds of genes across the genome. Inversion-affected loci (IAL) appear both within inversions as well as on unlinked chromosomes. Importantly, IAL do not appear to be influenced by the previously reported genome-wide expression correlation structure. We found that five genes involved with sterol uptake, four of which are Niemann-Pick Type 2 orthologs, are upregulated in flies with In(3R)Mo but do not have SNPs in linkage disequilibrium (LD) with the inversion. We speculate that this upregulation is driven by genetic variation in mod(mdg4) that is in LD with In(3R)Mo. We find that there is little evidence for a regional or position effect of inversions on gene expression at the chromosomal level, but do find evidence for the distal breakpoint of In(3R)Mo interrupting one gene and possibly disassociating the two flanking genes from regulatory elements. PMID:28916647

Evidence for oxygenic photosynthesis half a billion years before the Great Oxidation Event

NASA Astrophysics Data System (ADS)

Planavsky, Noah J.; Asael, Dan; Hofmann, Axel; Reinhard, Christopher T.; Lalonde, Stefan V.; Knudsen, Andrew; Wang, Xiangli; Ossa Ossa, Frantz; Pecoits, Ernesto; Smith, Albertus J. B.; Beukes, Nicolas J.; Bekker, Andrey; Johnson, Thomas M.; Konhauser, Kurt O.; Lyons, Timothy W.; Rouxel, Olivier J.

2014-04-01

The early Earth was characterized by the absence of oxygen in the ocean-atmosphere system, in contrast to the well-oxygenated conditions that prevail today. Atmospheric concentrations first rose to appreciable levels during the Great Oxidation Event, roughly 2.5-2.3 Gyr ago. The evolution of oxygenic photosynthesis is generally accepted to have been the ultimate cause of this rise, but it has proved difficult to constrain the timing of this evolutionary innovation. The oxidation of manganese in the water column requires substantial free oxygen concentrations, and thus any indication that Mn oxides were present in ancient environments would imply that oxygenic photosynthesis was ongoing. Mn oxides are not commonly preserved in ancient rocks, but there is a large fractionation of molybdenum isotopes associated with the sorption of Mo onto the Mn oxides that would be retained. Here we report Mo isotopes from rocks of the Sinqeni Formation, Pongola Supergroup, South Africa. These rocks formed no less than 2.95 Gyr ago in a nearshore setting. The Mo isotopic signature is consistent with interaction with Mn oxides. We therefore infer that oxygen produced through oxygenic photosynthesis began to accumulate in shallow marine settings at least half a billion years before the accumulation of significant levels of atmospheric oxygen.

Stable isotope fractionation of tungsten during adsorption on Fe and Mn (oxyhydr)oxides

NASA Astrophysics Data System (ADS)

Kashiwabara, Teruhiko; Kubo, Sayuri; Tanaka, Masato; Senda, Ryoko; Iizuka, Tsuyoshi; Tanimizu, Masaharu; Takahashi, Yoshio

2017-05-01

The similar, but not identical chemical properties of W compared with Mo suggest that the stable isotope system of W could be a novel proxy to explore the modern and ancient ocean as is the case in the well-established utility of Mo isotopes. We experimentally investigated the isotopic fractionation of W during adsorption on Fe and Mn (oxyhydr)oxides (ferrihydrite and δ-MnO2), a key process in the global ocean budget of this element. Our adsorption experiments confirmed that W isotopes fractionate substantially on both ferrihydrite and δ-MnO2: lighter W isotopes are preferentially adsorbed on both oxides as a result of equilibrium isotopic exchange between dissolved and adsorbed species, and the obtained values of Δ186/183Wliquid-solid (= δ186Wdissolved - δ186Wadsorbed) are 0.76 ± 0.09‰ for ferrihydrite and 0.88 ± 0.21‰ for δ-MnO2 (2σ, n = 6). Compared with the case of Mo isotopes, fractionation of W isotopes is (i) of comparable magnitude between ferrihydrite and δ-MnO2, and (ii) much smaller than that of Mo on δ-MnO2. Our previous XAFS observations and newly-performed DFT calculations both indicate that the observed W isotopic fractionations are caused by the symmetry change from Td (tetrahedral) WO42- to distorted Oh (octahedral) monomeric W species via formation of inner-sphere complexes on both ferrihydrite and δ-MnO2. The similar isotopic fractionations between the two oxides relate to the strong tendency for W to form inner-sphere complexes, which causes the symmetry change, in contrast to the outer-sphere complex of Mo on ferrihydrite. The smaller isotopic fractionation of W compared with Mo on δ-MnO2 despite their similar molecular symmetry seems to be due to their different degrees of distortion of Oh species. Our findings imply that the isotopic composition of W in modern oxic seawater is likely to become heavier relative to the input by removal of lighter W isotopes via adsorption on ferromanganese oxides in analogy with the Mo isotope budget. In contrast, the isotopic composition of W in ancient seawater should have evolved in response to the extent of deposition of both Fe and Mn oxides; this is likely to be different compared with that of the Mo isotopes, which is strongly associated with the occurrence of Mn oxides relative to Fe oxides.

Hydrolysis of ZrCl4 and HfCl4: The Initial Steps in the High-Temperature Oxidation of Metal Chlorides to Produce ZrO2 and HfO2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fang, Zongtang; Dixon, David A.

2013-03-08

The gas-phase hydrolysis of MCl4 (M = Zr, Hf) to produce the initial particles on the way to zirconia and hafnia nanoparticles has been studied with electronic structure theory. The potential energy surfaces, the themochemistry of the reaction species, and the reaction paths for the initial steps of MCl4 reacting with H2O have been calculated. The hydrolysis of MCl4 at higher temperatures begins with the formation of oxychlorohydroxides followed by the elimination of HCl instead of the direct production of MOCl2 and HCl or MO2 and HCl due to the substantial endothermicities associated with the formation of gas-phase MO2. Themore » structural properties and heats of formation of the reactants and products are consistent with the available experimental results. A number of metal oxychlorides (oxychlorohydroxides) intermediate clusters have been studied to assess their role in the production of MO2 nanoparticles. The calculated clustering reaction energies of those intermediates are highly exothermic, so they could be readily formed in the hydrolysis process. These intermediate clusters can be formed exothermically from metal oxychlorohydroxides by the elimination of one HCl or H2O molecule. Our calculations show that the mechanisms leading to the formation of MO2 nanoparticles are complicated and are accompanied by the potential production of a wide range of intermediates, as found for the production of TiO2 particles from the high-temperature oxidation of TiCl4.« less

Deficiency of Lipoprotein Lipase in Neurons Decreases AMPA Receptor Phosphorylation and Leads to Neurobehavioral Abnormalities in Mice

PubMed Central

Yu, Tian; Taussig, Matthew D.; DiPatrizio, Nicholas V.; Astarita, Giuseppe; Piomelli, Daniele; Bergman, Bryan C.; Dell’Acqua, Mark L.; Eckel, Robert H.; Wang, Hong

2015-01-01

Alterations in lipid metabolism have been found in several neurodegenerative disorders, including Alzheimer’s disease. Lipoprotein lipase (LPL) hydrolyzes triacylglycerides in lipoproteins and regulates lipid metabolism in multiple organs and tissues, including the central nervous system (CNS). Though many brain regions express LPL, the functions of this lipase in the CNS remain largely unknown. We developed mice with neuron-specific LPL deficiency that became obese on chow by 16 wks in homozygous mutant mice (NEXLPL-/-) and 10 mo in heterozygous mice (NEXLPL+/-). In the present study, we show that 21 mo NEXLPL+/- mice display substantial cognitive function decline including poorer learning and memory, and increased anxiety with no difference in general motor activities and exploratory behavior. These neurobehavioral abnormalities are associated with a reduction in the 2-amino-3-(3-hydroxy-5-methyl-isoxazol-4-yl) propanoic acid (AMPA) receptor subunit GluA1 and its phosphorylation, without any alterations in amyloid β accumulation. Importantly, a marked deficit in omega-3 and omega-6 polyunsaturated fatty acids (PUFA) in the hippocampus precedes the development of the neurobehavioral phenotype of NEXLPL+/- mice. And, a diet supplemented with n-3 PUFA can improve the learning and memory of NEXLPL+/- mice at both 10 mo and 21 mo of age. We interpret these findings to indicate that LPL regulates the availability of PUFA in the CNS and, this in turn, impacts the strength of synaptic plasticity in the brain of aging mice through the modification of AMPA receptor and its phosphorylation. PMID:26263173

Synthesis, structural and optical properties of BaMoO{sub 4}:Eu{sup 3+} shuttle like phosphors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krishna Bharat, L.; Lee, Soo Hyun; Yu, Jae Su, E-mail: jsyu@khu.ac.kr

2014-05-01

Graphical abstract: - Highlights: • BaMoO{sub 4}:Eu{sup 3+} phosphors were synthesized by a facile synthesis route. • PL and CL spectra showed dominant emissions due to ({sup 5}D{sub 0} → {sup 7}F{sub 2}) hypersensitive transitions. • The excitation wavelengths in the UV-B region make BaMoO{sub 4}:Eu{sup 3+} phosphors as a good candidate in the red region for the development of UV-based white LEDs. • PL and CL spectra showed similar CIE values close to the commercially available Y{sub 2}O{sub 3}:Eu{sup 3+} phosphors. - Abstract: Eu{sup 3+} ions doped BaMoO{sub 4} phosphor samples were synthesized by a facile synthesis process. Themore » tetragonal phase of the host lattice was substantiated by the X-ray diffraction patterns. The morphological studies were carried out by taking the scanning electron microscope and transmission electron microscope images and confirmed the formation of shuttle like particles with perpendicular protrusions in the middle of the particle. The single crystalline nature of the phosphors was confirmed by the selected area electron diffraction pattern. The photoluminescence (PL) properties of the Eu{sup 3+} ions doped samples revealed good emission with a high asymmetry ratio when excited with ultraviolet B wavelengths (between 280 and 315 nm). The cathodoluminescence (CL) spectra showed similar results to the PL spectra. The calculated CIE values based on the PL and CL spectra were almost similar and confirmed the rich red emission.« less

Mo isotope record of shales points to deep ocean oxygenation in the early Paleoproterozoic

NASA Astrophysics Data System (ADS)

Asael, Dan; Scott, Clint; Rouxel, Olivier; Poulton, Simon; Lyons, Timothy; Javaux, Emmanuelle; Bekker, Andrey

2014-05-01

Two steps in Earth's surface oxidation lie at either end of the Proterozoic Eon. The first step, known as the Great Oxidation Event (GOE), occurred at ca. 2.32 Ga (1), when atmospheric oxygen first exceeded 0.001% of present atmospheric levels (2). The second step, occurred at ca. 0.58 Ga, resulting in the pervasive oxygenation of the deep oceans, a feature that persisted through most of the Phanerozoic (3). The conventional model envisions two progressive and unidirectional increases in free oxygen. However, recent studies have challenged this simplistic view of the GOE (4, 5). A dramatic increase and decline in Earth oxidation state between 2.3 and 2.0 Ga is now well supported (6-9) and raises the question of how well-oxygenated the Earth surface was in the immediate aftermath of the GOE. In order to constrain the response of the deep oceans to the GOE, we present a study of Mo isotope composition and Mo concentration from three key early Paleoproterozoic black shale units with ages ranging from 2.32 to 2.06 Ga. Our results suggest high and unstable surface oxygen levels at 2.32 Ga, leading to an abrupt increase in Mo supply to the still globally anoxic ocean, and producing extreme seawater Mo isotopic enrichments in these black shales. We thus infer a period of significant Mo isotopic Rayleigh effects and non-steady state behaviour of the Mo oceanic system at the beginning of the GOE. Between 2.2-2.1 Ga, we observe smaller Mo isotopic variations and estimate the δ98Mo of seawater to be 1.42 ± 0.27 ‰W conclude that oxygen levels must have stabilized at a relatively high level and that the deep oceans were oxygenated for the first time in Earth's history. By ca. 2.06 Ga, immediately after the Lomagundi Event, the Mo isotopic composition decreased dramatically to δ98MoSW = 0.80 ± 0.21 o reflecting the end of deep ocean oxygenation and the return of largely anoxic deep oceans. References: [1] A. Bekker et al., 2004, Nature 427, 117-20. [2] A. Pavlov and J. Kasting, 2002, Astrobiology 2, 27-41. [3] C. Scott et al., 2008, Nature 452, 456-9. [4] C. Goldblatt et al., 2006, Nature 443, 683-6. [5] L. Kump et al., 2011, Science 334, 1694-6. [6] A. Bekker and D. Holland, 2012, Earth Planet. Sci. Lett. 317-318, 295-304. [7] N. Planavsky et al., 2012, Proc. Natl. Acad. Sci. U. S. A. 109, 18300-5. [8] C. Partin et al., 2013, Chem. Geol. 362, 82-90. [9] C. Scott et al., 2014, Earth Planet. Sci. Lett. 389, 95-104.

MoMaS reactive transport benchmark using PFLOTRAN

NASA Astrophysics Data System (ADS)

Park, H.

2017-12-01

MoMaS benchmark was developed to enhance numerical simulation capability for reactive transport modeling in porous media. The benchmark was published in late September of 2009; it is not taken from a real chemical system, but realistic and numerically challenging tests. PFLOTRAN is a state-of-art massively parallel subsurface flow and reactive transport code that is being used in multiple nuclear waste repository projects at Sandia National Laboratories including Waste Isolation Pilot Plant and Used Fuel Disposition. MoMaS benchmark has three independent tests with easy, medium, and hard chemical complexity. This paper demonstrates how PFLOTRAN is applied to this benchmark exercise and shows results of the easy benchmark test case which includes mixing of aqueous components and surface complexation. Surface complexations consist of monodentate and bidentate reactions which introduces difficulty in defining selectivity coefficient if the reaction applies to a bulk reference volume. The selectivity coefficient becomes porosity dependent for bidentate reaction in heterogeneous porous media. The benchmark is solved by PFLOTRAN with minimal modification to address the issue and unit conversions were made properly to suit PFLOTRAN.

Prototype Interoperability Document between NASA-JSC and DLR-GSOC Describing the CCSDS SM and C Mission Operations Prototype

NASA Technical Reports Server (NTRS)

Lucord, Steve A.; Gully, Sylvain

2009-01-01

The purpose of the PROTOTYPE INTEROPERABILITY DOCUMENT is to document the design and interfaces for the service providers and consumers of a Mission Operations prototype between JSC-OTF and DLR-GSOC. The primary goal is to test the interoperability sections of the CCSDS Spacecraft Monitor & Control (SM&C) Mission Operations (MO) specifications between both control centers. An additional goal is to provide feedback to the Spacecraft Monitor and Control (SM&C) working group through the Review Item Disposition (RID) process. This Prototype is considered a proof of concept and should increase the knowledge base of the CCSDS SM&C Mission Operations standards. No operational capabilities will be provided. The CCSDS Mission Operations (MO) initiative was previously called Spacecraft Monitor and Control (SM&C). The specifications have been renamed to better reflect the scope and overall objectives. The working group retains the name Spacecraft Monitor and Control working group and is under the Mission Operations and Information Services Area (MOIMS) of CCSDS. This document will refer to the specifications as SM&C Mission Operations, Mission Operations or just MO.

Method for fabricating uranium foils and uranium alloy foils

DOEpatents

Hofman, Gerard L [Downers Grove, IL; Meyer, Mitchell K [Idaho Falls, ID; Knighton, Gaven C [Moore, ID; Clark, Curtis R [Idaho Falls, ID

2006-09-05

A method of producing thin foils of uranium or an alloy. The uranium or alloy is cast as a plate or sheet having a thickness less than about 5 mm and thereafter cold rolled in one or more passes at substantially ambient temperatures until the uranium or alloy thereof is in the shape of a foil having a thickness less than about 1.0 mm. The uranium alloy includes one or more of Zr, Nb, Mo, Cr, Fe, Si, Ni, Cu or Al.

Improving the economic value of photographic screening for optical coherence tomography-detectable macular oedema: a prospective, multicentre, UK study.

PubMed

Olson, J; Sharp, P; Goatman, K; Prescott, G; Scotland, G; Fleming, A; Philip, S; Santiago, C; Borooah, S; Broadbent, D; Chong, V; Dodson, P; Harding, S; Leese, G; Styles, C; Swa, K; Wharton, H

2013-11-01

To determine the best photographic surrogate markers for detecting sight-threatening macular oedema (MO) in people with diabetes attending UK national screening programmes. A multicentre, prospective, observational cohort study of 3170 patients with photographic signs of diabetic retinopathy visible within the macular region [exudates within two disc diameters, microaneurysms/dot haemorrhages (M/DHs) and blot haemorrhages (BHs)] who were recruited from seven study centres. All patients were recruited and imaged at one of seven study centres in Aberdeen, Birmingham, Dundee, Dunfermline, Edinburgh, Liverpool and Oxford. Subjects with features of diabetic retinopathy visible within the macular region attending one of seven diabetic retinal screening programmes. Alternative referral criteria for suspected MO based on photographic surrogate markers; an optical coherence tomographic examination in addition to the standard digital retinal photograph. (1) To determine the best method to detect sight-threatening MO in people with diabetes using photographic surrogate markers. (2) Sensitivity and specificity estimates to assess the costs and consequences of using alternative strategies. (3) Modelled long-term costs and quality-adjusted life-years (QALYs). Prevalence of MO was strongly related to the presence of lesions and was roughly five times higher in subjects with exudates or BHs or more than two M/DHs within one disc diameter. Having worse visual acuity was associated with about a fivefold higher prevalence of MO. Current manual screening grading schemes that ignore visual acuity or the presence of M/DHs could be improved by taking these into account. Health service costs increase substantially with more sensitive/less specific strategies. A fully automated strategy, using the automated detection of patterns of photographic surrogate markers, is superior to all current manual grading schemes for detecting MO in people with diabetes. The addition of optical coherence tomography (OCT) to each strategy, prior to referral, results in a reduction in costs to the health service with no decrement in the number of MO cases detected. Compared with all current manual grading schemes, for the same sensitivity, a fully automated strategy, using the automated detection of patterns of photographic surrogate markers, achieves a higher specificity for detecting MO in people with diabetes, especially if visual acuity is included in the automated strategy. Overall, costs to the health service are likely to increase if more sensitive referral strategies are adopted over more specific screening strategies for MO, for only very small gains in QALYs. The addition of OCT to each screening strategy, prior to referral, results in a reduction in costs to the health service with no decrement in the number of MO cases detected. This study has been registered as REC/IRAS 07/S0801/107, UKCRN ID 9063 and NIHR HTA 06/402/49. This project was funded by the NIHR Health Technology Assessment programme and will be published in full in Health Technology Assessment; Vol. 17, No. 51. See the HTA programme website for further project information.

Intrafascial versus interfascial nerve sparing in radical prostatectomy for localized prostate cancer: a systematic review and meta-analysis.

PubMed

Weng, Hong; Zeng, Xian-Tao; Li, Sheng; Meng, Xiang-Yu; Shi, Ming-Jun; He, Da-Lin; Wang, Xing-Huan

2017-09-13

The present study aimed to systematically evaluate the effectiveness and safety of the intrafascial and interfascial nerve sparing (ITR-NS and ITE-NS) radical prostatectomy. PubMed, Embase, and Cochrane Library databases were searched for eligible studies. Meta-analysis with random-effects model was performed. Six comparative trials were selected and embraced in this research, including one randomized controlled trial, three prospective comparative trials, and two retrospective comparative trials. With regard to perioperative parameters, no significant association of operative time, blood loss, transfusion rates, duration of catheterization, and hospital stay existed between ITR-NS and ITE-NS. With respect to the functional results, ITR-NS had advantages in terms of both continence and potency recovery compared with ITE-NS. In reference to the oncologic results, the ITR-NS showed lower overall positive surgical margin (PSM) compared with ITE-NS but pT2 PSM and biochemical recurrence free rates were similar to the two surgical types. This study demonstrates that ITR-NS has better continence at 6 mo and 36 mo and better potency recovery at 6 mo and 12 mo postoperatively, regardless of the surgical technique. The cancer control of ITR-NS was also better than that of ITE-NS. This may be explained by the fact that patients in ITE-NS group present higher risk cancer than patients in ITR-NS group.

Soil quality assessment using GIS-based chemometric approach and pollution indices: Nakhlak mining district, Central Iran.

PubMed

Moore, Farid; Sheykhi, Vahideh; Salari, Mohammad; Bagheri, Adel

2016-04-01

This paper is a comprehensive assessment of the quality of soil in the Nakhlak mining district in Central Iran with special reference to potentially toxic metals. In this regard, an integrated approach involving geostatistical, correlation matrix, pollution indices, and chemical fractionation measurement is used to evaluate selected potentially toxic metals in soil samples. The fractionation of metals indicated a relatively high variability. Some metals (Mo, Ag, and Pb) showed important enrichment in the bioavailable fractions (i.e., exchangeable and carbonate), whereas the residual fraction mostly comprised Sb and Cr. The Cd, Zn, Co, Ni, Mo, Cu, and As were retained in Fe-Mn oxide and oxidizable fractions, suggesting that they may be released to the environment by changes in physicochemical conditions. The spatial variability patterns of 11 soil heavy metals (Ag, As, Cd, Co, Cr, Cu, Mo, Ni, Pb, Sb, and Zn) were identified and mapped. The results demonstrated that Ag, As, Cd, Mo, Cu, Pb, Sb, and Zn pollution are associated with mineralized veins and mining operations in this area. Further environmental monitoring and remedial actions are required for management of soil heavy metals in the study area. The present study not only enhanced our knowledge regarding soil pollution in the study area but also introduced a better technique to analyze pollution indices by multivariate geostatistical methods.

Predictors of cognitive impairment in an early stage Parkinson's disease cohort.

PubMed

Hu, Michele T M; Szewczyk-Królikowski, Konrad; Tomlinson, Paul; Nithi, Kannan; Rolinski, Michal; Murray, Clara; Talbot, Kevin; Ebmeier, Klaus P; Mackay, Clare E; Ben-Shlomo, Yoav

2014-03-01

The impact of Parkinson's disease (PD) dementia is substantial and has major functional and socioeconomic consequences. Early prediction of future cognitive impairment would help target future interventions. The Montreal Cognitive Assessment (MoCA), the Mini-Mental State Examination (MMSE), and fluency tests were administered to 486 patients with PD within 3.5 years of diagnosis, and the results were compared with those from 141 controls correcting for age, sex, and educational years. Eighteen-month longitudinal assessments were performed in 155 patients with PD. The proportion of patients classified with normal cognition, mild cognitive impairment (MCI), and dementia varied considerably, depending on the MoCA and MMSE thresholds used. With the MoCA total score at screening threshold, 47.7%, 40.5%, and 11.7% of patients with PD were classified with normal cognition, MCI, and dementia, respectively; by comparison, 78.7% and 21.3% of controls had normal cognition and MCI, respectively. Cognitive impairment was predicted by lower education, increased age, male sex, and quantitative motor and non-motor (smell, depression, and anxiety) measures. Longitudinal data from 155 patients with PD over 18 months showed significant reductions in MoCA scores, but not in MMSE scores, with 21.3% of patients moving from normal cognition to MCI and 4.5% moving from MCI to dementia, although 13.5% moved from MCI to normal; however, none of the patients with dementia changed their classification. The MoCA may be more sensitive than the MMSE in detecting early baseline and longitudinal cognitive impairment in PD, because it identified 25.8% of those who experienced significant cognitive decline over 18 months. Cognitive decline was associated with worse motor and non-motor features, suggesting that this reflects a faster progressive phenotype. © 2014 The Authors. International Parkinson and Movement Disorder Society published by Wiley Periodicals, Inc.

Phase transformation kinetics in rolled U-10 wt. % Mo foil: Effect of post-rolling heat treatment and prior γ-UMo grain size

DOE PAGES

Jana, Saumyadeep; Overman, Nicole; Varga, Tamas; ...

2017-09-25

Here, the effect of sub-eutectoid heat treatment on the phase transformation behavior in rolled U-10 wt.% Mo (U10Mo) foils was systematically investigated. The as-cast 5 mm thick foils were initially homogenized at 900 °C for 48 h and were hot rolled to 2 mm and later cold rolled down to 0.2 mm. Three starting microstructures were evaluated: (i) hot + cold-rolled to 0.2 mm (as-rolled condition), (ii) hot + cold-rolled to 0.2 mm + annealed at 700 °C for 1 h, and (iii) hot + cold-rolled to 0.2 mm + annealed at 1000 °C for 60 h. Annealing of as-rolledmore » materials at 700 °C resulted in small grain size (15 ± 9 μm average grain size), while annealing at 1000 °C led to very large grains (156 ± 118 μm average grain size) in rolled U10Mo foils. Later the samples were subjected to sub-eutectoid heat-treatment temperatures of 550 °C, 500 °C, and 400 °C for different durations of time starting from 1 h up to 100 h. U10Mo rolled foils went through various degrees of decomposition when subjected to the sub-eutectoid heat-treatment step and formed a lamellar microstructure through a cellular reaction mostly along the previous γ-UMo grain boundaries. The least amount of cellular reaction was observed in the large-grain microstructure at all temperatures. Conversely, a substantial amount of cellular reaction was observed in both the as-rolled and the small-grain microstructure. After 100 h of heat treatment at 500 °C, the volume fraction of the lamellar phase was found to be 4%, 22%, and 82% in large-grain, as-rolled, and small-grain samples, respectively.« less

Phase transformation kinetics in rolled U-10 wt. % Mo foil: Effect of post-rolling heat treatment and prior γ-UMo grain size

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jana, Saumyadeep; Overman, Nicole; Varga, Tamas

Here, the effect of sub-eutectoid heat treatment on the phase transformation behavior in rolled U-10 wt.% Mo (U10Mo) foils was systematically investigated. The as-cast 5 mm thick foils were initially homogenized at 900 °C for 48 h and were hot rolled to 2 mm and later cold rolled down to 0.2 mm. Three starting microstructures were evaluated: (i) hot + cold-rolled to 0.2 mm (as-rolled condition), (ii) hot + cold-rolled to 0.2 mm + annealed at 700 °C for 1 h, and (iii) hot + cold-rolled to 0.2 mm + annealed at 1000 °C for 60 h. Annealing of as-rolledmore » materials at 700 °C resulted in small grain size (15 ± 9 μm average grain size), while annealing at 1000 °C led to very large grains (156 ± 118 μm average grain size) in rolled U10Mo foils. Later the samples were subjected to sub-eutectoid heat-treatment temperatures of 550 °C, 500 °C, and 400 °C for different durations of time starting from 1 h up to 100 h. U10Mo rolled foils went through various degrees of decomposition when subjected to the sub-eutectoid heat-treatment step and formed a lamellar microstructure through a cellular reaction mostly along the previous γ-UMo grain boundaries. The least amount of cellular reaction was observed in the large-grain microstructure at all temperatures. Conversely, a substantial amount of cellular reaction was observed in both the as-rolled and the small-grain microstructure. After 100 h of heat treatment at 500 °C, the volume fraction of the lamellar phase was found to be 4%, 22%, and 82% in large-grain, as-rolled, and small-grain samples, respectively.« less

Reference Ranges for Transvaginal Examined Fossa Posterior Structures in Fetuses from 45 to 84 mm Crown-Rump Length.

PubMed

Altmann, Reinhard; Specht, Christian; Scharnreitner, Iris; Schertler, Caroline; Mayer, Richard; Arzt, Wolfgang; Scheier, Matthias

2018-06-05

The study aimed to describe reference values for structures of the posterior fossa in fetuses with a crown-rump length (CRL) between 45 and 84 mm. This was a prospective, cross-sectional study including 216 normal appearing fetuses. In transvaginal acquired 3-dimensional volume blocks, the longest diameter of the vermis (VE), posterior membranous area (PMA), medulla-oblongata-pons angle (MOPA), diameters of the medulla oblongata (MO) and pons (PO), and the area of Blake's pouch (BP) were measured. Polynomial or linear regression analysis were performed to calculate the mean, 5th and 95th centile according to CRL. In 20 fetuses, intra- and interobserver repeatability were calculated. There is a curvilinear correlation between CRL and PO (PO [mean] = 1.3893 + 0.004356 × CRL + 0.000002610 × CRL3; SD = 1.6818 - 0.03765 × CRL + 0.000003831 × CRL3; R2 = 0.489); CRL and MO (MO [mean] = 1.5959-0.001905 × CRL + 0.000003362*CRL3; SD = -0.1417 + 0.005404 × CRL + 0.0000004988 × CRL3; R2 = 0.525); CRL and VE (VE [mean] = -0.3640 + 0.04302 × CRL+ 0.000001486 × CRL3; SD = 0.5854 - 0.004812 × CRL + 0.0000005896 × CRL3; R2 = 0.643); CRL and PMA (PMA [mean] = 0.6901 + 0.04307 × CRL - 0.0000008459 × CRL3; SD = -0.4232 + 0.02026 × CRL - 0.000001320 × CRL3; R2 = 0.272); CRL and BP (mm2; BP [mean] -12.2067 + 0.3334 × CRL - 0.00001262 × CRL3; SD = -1.6431 + 0.06380 × CRL+ 0.0000003257 × CRL3; R2 = 0.289). The relation between CRL and MOPA (°) is best described by a linear regression (MOPA [mean] = 79.6332 + 0.6122 × CRL; SD = 4.8453 + 0.07333 × CRL; R2 = 0.318). We provide reference values for anatomical structures of the posterior fossa of fetuses between 45 and 84 mm CRL. The established reference values might ease the diagnosis of fetal malformations in early pregnancy. © 2018 S. Karger AG, Basel.

77 FR 68073 - Prevailing Rate Systems; Redefinition of the St. Louis, MO; Southern Missouri; Cleveland, OH; and...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-15

... Albuquerque, NM, and El Paso, TX, wage areas to White Sands Missile Range. DATES: We must receive comments on... because the Department of Defense now refers to it as that White Sands Missile Range. OPM announced these... not include White Sands Missile Range portion) Los Alamos Mora Quay Rio Arriba Roosevelt San Miguel...

"The Boy in the Dress": Queering Mantle of the Expert

ERIC Educational Resources Information Center

Terret, Liselle

2013-01-01

In this paper I offer a queer analysis of several key moments during a Mantle of the Expert (MoE) project that resulted in Year 5 children creating performances and engaging with heightened versions of gendered femininity in their primary school. I will refer to theoretical notions of transvestism as a means of challenging the notions of binarism,…

Generation of Referring Expressions: Assessing the Incremental Algorithm

ERIC Educational Resources Information Center

van Deemter, Kees; Gatt, Albert; van der Sluis, Ielka; Power, Richard

2012-01-01

A substantial amount of recent work in natural language generation has focused on the generation of "one-shot" referring expressions whose only aim is to identify a target referent. Dale and Reiter's Incremental Algorithm (IA) is often thought to be the best algorithm for maximizing the similarity to referring expressions produced by people. We…

Use of a "Super-child" Approach to Assess the Vitamin A Equivalence of Moringa oleifera Leaves, Develop a Compartmental Model for Vitamin A Kinetics, and Estimate Vitamin A Total Body Stores in Young Mexican Children.

PubMed

Lopez-Teros, Veronica; Ford, Jennifer Lynn; Green, Michael H; Tang, Guangwen; Grusak, Michael A; Quihui-Cota, Luis; Muzhingi, Tawanda; Paz-Cassini, Mariela; Astiazaran-Garcia, Humberto

2017-12-01

Background: Worldwide, an estimated 250 million children <5 y old are vitamin A (VA) deficient. In Mexico, despite ongoing efforts to reduce VA deficiency, it remains an important public health problem; thus, food-based interventions that increase the availability and consumption of provitamin A-rich foods should be considered. Objective: The objectives were to assess the VA equivalence of 2 H-labeled Moringa oleifera (MO) leaves and to estimate both total body stores (TBS) of VA and plasma retinol kinetics in young Mexican children. Methods: β-Carotene was intrinsically labeled by growing MO plants in a 2 H 2 O nutrient solution. Fifteen well-nourished children (17-35 mo old) consumed puréed MO leaves (1 mg β-carotene) and a reference dose of [ 13 C 10 ]retinyl acetate (1 mg) in oil. Blood (2 samples/child) was collected 10 times (2 or 3 children each time) over 35 d. The bioefficacy of MO leaves was calculated from areas under the composite "super-child" plasma isotope response curves, and MO VA equivalence was estimated through the use of these values; a compartmental model was developed to predict VA TBS and retinol kinetics through the use of composite plasma [ 13 C 10 ]retinol data. TBS were also estimated with isotope dilution. Results: The relative bioefficacy of β-carotene retinol activity equivalents from MO was 28%; VA equivalence was 3.3:1 by weight (0.56 μmol retinol:1 μmol β-carotene). Kinetics of plasma retinol indicate more rapid plasma appearance and turnover and more extensive recycling in these children than are observed in adults. Model-predicted mean TBS (823 μmol) was similar to values predicted using a retinol isotope dilution equation applied to data from 3 to 6 d after dosing (mean ± SD: 832 ± 176 μmol; n = 7). Conclusions: The super-child approach can be used to estimate population carotenoid bioefficacy and VA equivalence, VA status, and parameters of retinol metabolism from a composite data set. Our results provide initial estimates of retinol kinetics in well-nourished young children with adequate VA stores and demonstrate that MO leaves may be an important source of VA. © 2017 American Society for Nutrition.

Endoscopic sphincterotomy: follow-up evaluation of effects on the sphincter of Oddi.

PubMed

Geenen, J E; Toouli, J; Hogan, W J; Dodds, W J; Stewart, E T; Mavrelis, P; Riedel, D; Venu, R

1984-10-01

Endoscopic sphincterotomy (ES) alters the structure and motor function of the sphincter of Oddi (SO). The magnitude and duration of these changes, however, have not been critically examined. Before ES, 22 patients with common bile duct stones were evaluated by endoscopic retrograde cholangiography. The pressure gradient between the common bile duct and the duodenum, the SO basal pressure, and the SO peak phasic pressures were obtained. After ES, the electrosurgical incision length was determined using the extended papillotome and an inflated Fogarty balloon as reference. A high correlation existed between the endoscopist's estimate of ES incision size using this technique and the actual length of simulated incisions fashioned in cardboard mounts. These studies were repeated in all 22 patients at 1-yr follow-up and in 8 of these patients at 2-yr follow-up. At 12 mo and 24 mo after ES, the common bile duct (CBD) to duodenal pressure gradient and the sphincter of Oddi basal pressure were virtually eliminated. The amplitude of SO phasic contractions was significantly diminished 12 mo after ES (124 +/- 16 mmHg to 37 +/- 10 mmHg; p less than 0.001), but 24 mo after ES, SO phasic contraction amplitude was not significantly different from the values before ES. Incision length at 1-yr follow-up was reduced in the group of 22 patients from 11.6 +/- 0.8 mm to 8.3 +/- 0.5 mm (p less than 0.001), and in the group of 8 patients from 11.0 +/- 1.5 mm to 7.5 +/- 0.7 mm (p less than 0.025). After an additional 12 mo, however, i.e., 24 mo after ES, the incision length was 6.5 +/- 0.7 mm. There was no significant difference in incision length between the 12-mo and 24-mo examinations. We conclude that after ES, incision length decreases during the first year. There appears to be no further significant reduction in incision length at 2 yr. In addition, the reduction of the CBD to duodenal pressure gradient and the SO basal pressure remain unchanged for at least 2 yr. These manometric findings support the observation that after ES the enlarged opening of the CBD into the duodenum remains open for at least 2 yr.

Minimizing residues and strain in 2D materials transferred from PDMS.

PubMed

Jain, Achint; Bharadwaj, Palash; Heeg, Sebastian; Parzefall, Markus; Taniguchi, Takashi; Watanabe, Kenji; Novotny, Lukas

2018-06-29

Integrating layered two-dimensional (2D) materials into 3D heterostructures offers opportunities for novel material functionalities and applications in electronics and photonics. In order to build the highest quality heterostructures, it is crucial to preserve the cleanliness and morphology of 2D material surfaces that come in contact with polymers such as PDMS during transfer. Here we report that substantial residues and up to ∼0.22% compressive strain can be present in monolayer MoS 2 transferred using PDMS. We show that a UV-ozone pre-cleaning of the PDMS surface before exfoliation significantly reduces organic residues on transferred MoS 2 flakes. An additional 200 ◦ C vacuum anneal after transfer efficiently removes interfacial bubbles and wrinkles as well as accumulated strain, thereby restoring the surface morphology of transferred flakes to their native state. Our recipe is important for building clean heterostructures of 2D materials and increasing the reproducibility and reliability of devices based on them.

Preventing Thin Film Dewetting via Graphene Capping.

PubMed

Cao, Peigen; Bai, Peter; Omrani, Arash A; Xiao, Yihan; Meaker, Kacey L; Tsai, Hsin-Zon; Yan, Aiming; Jung, Han Sae; Khajeh, Ramin; Rodgers, Griffin F; Kim, Youngkyou; Aikawa, Andrew S; Kolaczkowski, Mattew A; Liu, Yi; Zettl, Alex; Xu, Ke; Crommie, Michael F; Xu, Ting

2017-09-01

A monolayer 2D capping layer with high Young's modulus is shown to be able to effectively suppress the dewetting of underlying thin films of small organic semiconductor molecule, polymer, and polycrystalline metal, respectively. To verify the universality of this capping layer approach, the dewetting experiments are performed for single-layer graphene transferred onto polystyrene (PS), semiconducting thienoazacoronene (EH-TAC), gold, and also MoS 2 on PS. Thermodynamic modeling indicates that the exceptionally high Young's modulus and surface conformity of 2D capping layers such as graphene and MoS 2 substantially suppress surface fluctuations and thus dewetting. As long as the uncovered area is smaller than the fluctuation wavelength of the thin film in a dewetting process via spinodal decomposition, the dewetting should be suppressed. The 2D monolayer-capping approach opens up exciting new possibilities to enhance the thermal stability and expands the processing parameters for thin film materials without significantly altering their physical properties. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

An HIT Solution for Clinical Care and Disaster Planning: How One health Center in Joplin, MO Survived a Tornado and Avoided a Health Information Disaster.

PubMed

Shin, Peter; Jacobs, Feygele

2012-01-01

Since taking office, President Obama has made substantial investments in promoting the diffusion of health information technology (IT). The objective of the national health IT program is, generally, to enable health care providers to better manage patient care through secure use and sharing of health information. Through the use of technologies including electronic health records, providers can better maintain patient care information and facilitate communication, often improving care outcomes. The recent tornado in Joplin, MO highlights the importance of health information technology in the health center context, and illustrates the importance of secure electronic health information systems as a crucial element of disaster and business continuity planning. This article examines the experience of a community health center in the aftermath of the major tornado that swept through the American Midwest in the spring of 2011, and provides insight into the planning for disaster survival and recovery as it relates to patient records and health center data.

An HIT Solution for Clinical Care and Disaster Planning: How One health Center in Joplin, MO Survived a Tornado and Avoided a Health Information Disaster

PubMed Central

Shin, Peter; Jacobs, Feygele

2012-01-01

Since taking office, President Obama has made substantial investments in promoting the diffusion of health information technology (IT). The objective of the national health IT program is, generally, to enable health care providers to better manage patient care through secure use and sharing of health information. Through the use of technologies including electronic health records, providers can better maintain patient care information and facilitate communication, often improving care outcomes. The recent tornado in Joplin, MO highlights the importance of health information technology in the health center context, and illustrates the importance of secure electronic health information systems as a crucial element of disaster and business continuity planning. This article examines the experience of a community health center in the aftermath of the major tornado that swept through the American Midwest in the spring of 2011, and provides insight into the planning for disaster survival and recovery as it relates to patient records and health center data. PMID:23569622

Electromechanics in MoS2 and WS2: nanotubes vs. monolayers

PubMed Central

Ghorbani-Asl, Mahdi; Zibouche, Nourdine; Wahiduzzaman, Mohammad; Oliveira, Augusto F.; Kuc, Agnieszka; Heine, Thomas

2013-01-01

The transition-metal dichalcogenides (TMD) MoS2 and WS2 show remarkable electromechanical properties. Strain modifies the direct band gap into an indirect one, and substantial strain even induces an semiconductor-metal transition. Providing strain through mechanical contacts is difficult for TMD monolayers, but state-of-the-art for TMD nanotubes. We show using density-functional theory that similar electromechanical properties as in monolayer and bulk TMDs are found for large diameter TMD single- (SWNT) and multi-walled nanotubes (MWNTs). The semiconductor-metal transition occurs at elongations of 16%. We show that Raman signals of the in-plane and out-of-plane lattice vibrations depend significantly and linearly on the strain, showing that Raman spectroscopy is an excellent tool to determine the strain of the individual nanotubes and hence monitor the progress of nanoelectromechanical experiments in situ. TMD MWNTs show twice the electric conductance compared to SWNTs, and each wall of the MWNTs contributes to the conductance proportional to its diameter. PMID:24129919

Minimizing residues and strain in 2D materials transferred from PDMS

NASA Astrophysics Data System (ADS)

Jain, Achint; Bharadwaj, Palash; Heeg, Sebastian; Parzefall, Markus; Taniguchi, Takashi; Watanabe, Kenji; Novotny, Lukas

2018-06-01

Integrating layered two-dimensional (2D) materials into 3D heterostructures offers opportunities for novel material functionalities and applications in electronics and photonics. In order to build the highest quality heterostructures, it is crucial to preserve the cleanliness and morphology of 2D material surfaces that come in contact with polymers such as PDMS during transfer. Here we report that substantial residues and up to ∼0.22% compressive strain can be present in monolayer MoS2 transferred using PDMS. We show that a UV-ozone pre-cleaning of the PDMS surface before exfoliation significantly reduces organic residues on transferred MoS2 flakes. An additional 200 ◦C vacuum anneal after transfer efficiently removes interfacial bubbles and wrinkles as well as accumulated strain, thereby restoring the surface morphology of transferred flakes to their native state. Our recipe is important for building clean heterostructures of 2D materials and increasing the reproducibility and reliability of devices based on them.

Revised Tijeras Arroyo Groundwater Current Conceptual Model and Corrective Measures Evaluation Report - February 2018.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Copland, John R.

The U.S. Department of Energy (DOE) and the management and operating (M&O) contractor for Sandia National Laboratories beginning on May 1, 2017, National Technology & Engineering Solutions of Sandia, LLC (NTESS), hereinafter collectively referred to as DOE/NTESS, prepared this Revised Tijeras Arroyo Groundwater Current Conceptual Model (CCM) and Corrective Measures Evaluation (CME) Report , referred to as the Revised CCM/CME Report, to meet requirements under the Sandia National Laboratories-New Mexico (SNL/NM) Compliance Order on Consent (Consent Order). The Consent Order became effective on April 29, 2004. The Consent Order identifies the Tijeras Arroyo Groundwater (TAG) Area of Concern (AOC) asmore » an area of groundwater contamination requiring further characterization and corrective action. In November 2004, New Mexico Environment Department (NMED) approved the July 2004 CME Work Plan. In April 2005, DOE and the SNL M&O contractor at the time, Sandia Corporation (Sandia), hereinafter collectively referred to as DOE/Sandia, submitted a CME Report, but NMED did not finalize review of that document. In December 2016, DOE/Sandia submitted a combined and updated CCM/CME Report. NMED issued a disapproval letter in May 2017 that included comments on the December 2016 CCM/CME Report. In August 2017, NMED and DOE/NTESS staff held a meeting to discuss and clarify outstanding issues. This Revised CCM/CME Report addresses (1) the issues presented in the NMED May 2017 disapproval letter and (2) findings from the August 2017 meeting.« less

Minor neurological dysfunction in children with autism spectrum disorder.

PubMed

De Jong, Marianne; Punt, Marja; De Groot, Erik; Minderaa, Ruud B; Hadders-Algra, Mijna

2011-07-01

The aim of this study was to improve the understanding of brain function in children with autism spectrum disorder (ASD) in relation to minor neurological dysfunctions (MNDs). We studied MNDs in 122 children (93 males, 29 females; mean age 8 y 1 mo, SD 2 y 6 mo) who, among a total cohort of 705 children (513 males, 192 females; mean age 9 y, SD 2 y 0.5 mo) referred to a regional outpatient non-academic psychiatric centre in the Netherlands, were diagnosed with ASD after an extensive multidisciplinary psychiatric assessment. Children with clear neurological abnormalities (e.g. cerebral palsy or spina bifida) were excluded from the study. MNDs were assessed in all 705 children using the Touwen examination method. Special attention was paid to the severity and type of MND. Data of the children with ASD were compared with neurological morbidity data of children with other psychiatric disorders and with children in the general population, who were born at Groningen University Hospital between 1975 and 1978. Seventy-four percent of the children with ASD showed complex MNDs compared with 52% of the children with other psychiatric disorders and 6% of the reference group (χ(2) =18.0, p<0.001; χ(2) =937.5, p<0.001 respectively). Specific dysfunctions frequently encountered in ASD were dysfunctional posture and muscle tone, fine manipulative disability, dyscoordination, and excessive associated movements. These findings suggest a contribution of dysfunctional supraspinal networks involving multiple parts of the brain in the pathogenesis of ASD. This is consistent with findings from neuroimaging studies, and highlights the importance of neurological examinations in paediatric psychiatric assessments. © The Authors. Developmental Medicine & Child Neurology © 2011 Mac Keith Press.

Snapshot of an integrated psychosocial gastroenterology service

PubMed Central

Kinsinger, Sarah W; Ballou, Sarah; Keefer, Laurie

2015-01-01

AIM: To characterize the patients utilizing a gastroenterology behavioral medicine service and examine the effect of treatment on health care utilization. METHODS: Patients were referred by their gastroenterologists for psychological treatment during a 15 mo period. Patients seen for an intake with a psychologist completed the Brief Symptom Inventory (BSI) and a checklist of psychosocial concerns. A subset of patients with functional bowel disorders also completed a disease specific quality of life measure. Chart review was conducted to obtain information on type and frequency of sessions with the psychologist, the number of outpatient gastroenterology visits, and number of gastroenterology-related medical procedures during the 6 mo following psychological intake. RESULTS: Of 259 patients referred for treatment, 118 (46%) completed an intake with a psychologist. Diagnoses included: irritable bowel syndrome (42%), functional dyspepsia (20%), inflammatory bowel diseases (20%), esophageal symptoms (10%), and “other” (8%). Demographic variables and disease type did not differentiate between those who did and did not schedule an intake. Mean t-scores for the BSI global score index and the depression, anxiety, and somatization subscales fell below the cutoff for clinical significance (t = 63). Treatments were predominantly gut-directed hypnosis (48%) and cognitive behavioral therapy (44%). Average length of treatment was 4 sessions. Among functional gastrointestinal (GI) patients, those patients who initiated treatment received significantly fewer GI-related medical procedures during the 6 mo following the referral than patients who did not schedule an intake [t (197) = 2.69, P < 0.01]. CONCLUSION: Patients are receptive to psychological interventions for GI conditions and there is preliminary evidence that treatment can decrease health-care utilization among patients with functional GI conditions. PMID:25684957

The Oportunidades program increases the linear growth of children enrolled at young ages in urban Mexico.

PubMed

Leroy, Jef L; García-Guerra, Armando; García, Raquel; Dominguez, Clara; Rivera, Juan; Neufeld, Lynnette M

2008-04-01

The goal of this study was to evaluate the impact of Mexico's conditional cash transfer program, Oportunidades, on the growth of children <24 mo of age living in urban areas. Beneficiary families received cash transfers, a fortified food (targeted to pregnant and lactating women, children 6-23 mo, and children with low weight 2-4 y), and curative health services, among other benefits. Program benefits were conditional on preventative health care utilization and attendance of health and nutrition education sessions. We estimated the impact of the program after 2 y of operation in a panel of 432 children <24 mo of age at baseline (2002). We used difference-in-difference propensity score matching, which takes into account nonrandom program participation and the effects of unobserved fixed characteristics on outcomes. All models controlled for child age, sex, baseline anthropometry, and maternal height. Anthropometric Z-scores were calculated using the new WHO growth reference standards. There was no overall association between program participation and growth in children 6 to 24 mo of age. Children in intervention families younger than 6 mo of age at baseline grew 1.5 cm (P < 0.05) more than children in comparison families, corresponding to 0.41 height-for-age Z-scores (HAZ) (P < 0.05). They also gained an additional 0.76 kg (P < 0.01) or 0.47 weight-for-height Z-scores (P < 0.05). Children living in the poorest intervention households tended (0.05 < P < 0.10) to be taller than comparison children (0.9 cm, 0.27 HAZ). Oportunidades, with its strong nutrition component, is an effective tool to improve the growth of infants in poor urban households.

The MGED Ontology: a resource for semantics-based description of microarray experiments.

PubMed

Whetzel, Patricia L; Parkinson, Helen; Causton, Helen C; Fan, Liju; Fostel, Jennifer; Fragoso, Gilberto; Game, Laurence; Heiskanen, Mervi; Morrison, Norman; Rocca-Serra, Philippe; Sansone, Susanna-Assunta; Taylor, Chris; White, Joseph; Stoeckert, Christian J

2006-04-01

The generation of large amounts of microarray data and the need to share these data bring challenges for both data management and annotation and highlights the need for standards. MIAME specifies the minimum information needed to describe a microarray experiment and the Microarray Gene Expression Object Model (MAGE-OM) and resulting MAGE-ML provide a mechanism to standardize data representation for data exchange, however a common terminology for data annotation is needed to support these standards. Here we describe the MGED Ontology (MO) developed by the Ontology Working Group of the Microarray Gene Expression Data (MGED) Society. The MO provides terms for annotating all aspects of a microarray experiment from the design of the experiment and array layout, through to the preparation of the biological sample and the protocols used to hybridize the RNA and analyze the data. The MO was developed to provide terms for annotating experiments in line with the MIAME guidelines, i.e. to provide the semantics to describe a microarray experiment according to the concepts specified in MIAME. The MO does not attempt to incorporate terms from existing ontologies, e.g. those that deal with anatomical parts or developmental stages terms, but provides a framework to reference terms in other ontologies and therefore facilitates the use of ontologies in microarray data annotation. The MGED Ontology version.1.2.0 is available as a file in both DAML and OWL formats at http://mged.sourceforge.net/ontologies/index.php. Release notes and annotation examples are provided. The MO is also provided via the NCICB's Enterprise Vocabulary System (http://nciterms.nci.nih.gov/NCIBrowser/Dictionary.do). Stoeckrt@pcbi.upenn.edu Supplementary data are available at Bioinformatics online.

Preconcentration and determination of vanadium and molybdenum in milk, vegetables and foodstuffs by ultrasonic-thermostatic-assisted cloud point extraction coupled to flame atomic absorption spectrometry.

PubMed

Gürkan, Ramazan; Korkmaz, Sema; Altunay, Nail

2016-08-01

A new ultrasonic-thermostatic-assisted cloud point extraction procedure (UTA-CPE) was developed for preconcentration at the trace levels of vanadium (V) and molybdenum (Mo) in milk, vegetables and foodstuffs prior to determination via flame atomic absorption spectrometry (FAAS). The method is based on the ion-association of stable anionic oxalate complexes of V(V) and Mo(VI) with [9-(diethylamino)benzo[a]phenoxazin-5-ylidene]azanium; sulfate (Nile blue A) at pH 4.5, and then extraction of the formed ion-association complexes into micellar phase of polyoxyethylene(7.5)nonylphenyl ether (PONPE 7.5). The UTA-CPE is greatly simplified and accelerated compared to traditional cloud point extraction (CPE). The analytical parameters optimized are solution pH, the concentrations of complexing reagents (oxalate and Nile blue A), the PONPE 7.5 concentration, electrolyte concentration, sample volume, temperature and ultrasonic power. Under the optimum conditions, the calibration curves for Mo(VI) and V(V) are obtained in the concentration range of 3-340µgL(-1) and 5-250µgL(-1) with high sensitivity enhancement factors (EFs) of 145 and 115, respectively. The limits of detection (LODs) for Mo(VI) and V(V) are 0.86 and 1.55µgL(-1), respectively. The proposed method demonstrated good performances such as relative standard deviations (as RSD %) (≤3.5%) and spiked recoveries (95.7-102.3%). The accuracy of the method was assessed by analysis of two standard reference materials (SRMs) and recoveries of spiked solutions. The method was successfully applied into the determination of trace amounts of Mo(VI) and V(V) in milk, vegetables and foodstuffs with satisfactory results. Copyright © 2016 Elsevier B.V. All rights reserved.

A Multiplex PCR Approach for Detecting Dual Infections and Recombinants Involving Major HIV Variants

PubMed Central

Cappy, Pierre; De Oliveira, Fabienne; Gueudin, Marie; Alessandri-Gradt, Elodie

2016-01-01

The cocirculation of different HIV types and groups can lead to dual infections and recombinants, which hinder diagnosis and therapeutic management. We designed two multiplex PCRs (mPCRs) coupled with capillary electrophoresis to facilitate the detection of such infections. The first, MMO2, targets three variants (HIV-1/M, HIV-1/O, and HIV-2), and the second, MMO, targets HIV-1/M and HIV-1/O. These mPCRs were validated on DNA and RNA extracts from 19 HIV-1/M, 12 HIV-1/O, and 13 HIV-2 cultures and from mixtures simulating dual infections. They were then assessed with DNA and RNA extracts from samples of 47 clinical monoinfections and HIV-1/M+O dual infections or infections with HIV-1/MO recombinants. Both mPCRs had excellent specificity. Sensitivities ranged from 80 to 100% for in vitro samples and from 58 to 100% for clinical samples, with the results obtained depending on the material used and the region of the genome concerned. Sensitivity was generally lower for DNA than for RNA and for amplifications of the integrase and matrix regions. In terms of global detection (at least one target gene for each strain), both mPCRs yielded a detection rate of 100% for in vitro samples. MMO2 detected 100% of the clinical strains from DNA and 97% from RNA, whereas MMO detected 100% of the strains from both materials. Thus, for in vitro and clinical samples, MMO2 was a useful tool for detecting dual infections with HIV-1 and HIV-2 (referred to as HIV-1+HIV-2) and HIV-1/M+O, and MMO was useful for detecting both MO dual infections and MO mosaic patterns. PMID:26912747

High-Frame-Rate Speckle-Tracking Echocardiography.

PubMed

Joos, Philippe; Poree, Jonathan; Liebgott, Herve; Vray, Didier; Baudet, Mathilde; Faurie, Julia; Tournoux, Francois; Cloutier, Guy; Nicolas, Barbara; Garcia, Damien; Baudet, Mathilde; Tournoux, Francois; Joos, Philippe; Poree, Jonathan; Cloutier, Guy; Liebgott, Herve; Faurie, Julia; Vray, Didier; Nicolas, Barbara; Garcia, Damien

2018-05-01

Conventional echocardiography is the leading modality for noninvasive cardiac imaging. It has been recently illustrated that high-frame-rate echocardiography using diverging waves could improve cardiac assessment. The spatial resolution and contrast associated with this method are commonly improved by coherent compounding of steered beams. However, owing to fast tissue velocities in the myocardium, the summation process of successive diverging waves can lead to destructive interferences if motion compensation (MoCo) is not considered. Coherent compounding methods based on MoCo have demonstrated their potential to provide high-contrast B-mode cardiac images. Ultrafast speckle-tracking echocardiography (STE) based on common speckle-tracking algorithms could substantially benefit from this original approach. In this paper, we applied STE on high-frame-rate B-mode images obtained with a specific MoCo technique to quantify the 2-D motion and tissue velocities of the left ventricle. The method was first validated in vitro and then evaluated in vivo in the four-chamber view of 10 volunteers. High-contrast high-resolution B-mode images were constructed at 500 frames/s. The sequences were generated with a Verasonics scanner and a 2.5-MHz phased array. The 2-D motion was estimated with standard cross correlation combined with three different subpixel adjustment techniques. The estimated in vitro velocity vectors derived from STE were consistent with the expected values, with normalized errors ranging from 4% to 12% in the radial direction and from 10% to 20% in the cross-range direction. Global longitudinal strain of the left ventricle was also obtained from STE in 10 subjects and compared to the results provided by a clinical scanner: group means were not statistically different ( value = 0.33). The in vitro and in vivo results showed that MoCo enables preservation of the myocardial speckles and in turn allows high-frame-rate STE.

Spectroscopic characterization of novel multilayer mirrors intended for astronomical and laboratory applications

NASA Astrophysics Data System (ADS)

Ragozin, Eugene N.; Mednikov, Konstantin N.; Pertsov, Andrei A.; Pirozhkov, Alexander S.; Reva, Anton A.; Shestov, Sergei V.; Ul'yanov, Artem S.; Vishnyakov, Eugene A.

2009-05-01

We report measurements of the reflection spectra of (i) concave (spherical and parabolic) Mo/Si, Mg/Si, and Al/Zr multilayer mirrors (MMs) intended for imaging solar spectroscopy in the framework of the TESIS/CORONAS-FOTON Satellite Project and of (ii) an aperiodic Mo/Si MM optimized for maximum uniform reflectivity in the 125-250 Å range intended for laboratory applications. The reflection spectra were measured in the configuration of a transmission grating spectrometer employing the radiation of a tungsten laser-driven plasma as the source. The function of detectors was fulfilled by backside-illuminated CCDs coated with Al or Zr/Si multilayer absorption filters. High-intensity second-order interference reflection peaks at wavelengths of about 160 Å were revealed in the reflection spectra of the 304-Å Mo/Si MMs. By contrast, the second-order reflection peak in the spectra of the new-generation narrow-band (~12 Å FWHM) 304-Å Mg/Si MMs is substantially depressed. Manifestations of the NEXAFS structure of the L2, 3 absorption edges of Al and Al2O3 were observed in the spectra recorded. The broadband Mo/Si MM was employed as the focusing element of spectrometers in experiments involving (i) the charge exchange of multiply charged ions with the donor atoms of a rare-gas jet; (ii) the spectroscopic characterization of a debris-free soft X-ray radiation source excited by Nd laser pulses in a Xe jet (iii) near-IR-to-soft-X-ray frequency conversion (double Doppler effect) occurring in the retroreflection from the relativistic electron plasma wake wave (flying mirror) driven by a multiterawatt laser in a pulsed helium jet.

Combined Effects of Mass and Velocity on Forward Displacement and Phenomenological Ratings: A Functional Measurement Approach to the Momentum Metaphor

ERIC Educational Resources Information Center

De Sa Teixeira, Nuno; Oliveira, Armando Monica; Amorim, Michel-Ange

2010-01-01

Representational Momentum (RepMo) refers to the phenomenon that the vanishing position of a moving target is perceived as displaced ahead in the direction of movement. Originally taken to reflect a strict internalization of physical momentum, the finding that the target implied mass did not have an effect led to its subsequent reinterpretation as…

Toward Worldwide Hepcidin Assay Harmonization: Identification of a Commutable Secondary Reference Material.

PubMed

van der Vorm, Lisa N; Hendriks, Jan C M; Laarakkers, Coby M; Klaver, Siem; Armitage, Andrew E; Bamberg, Alison; Geurts-Moespot, Anneke J; Girelli, Domenico; Herkert, Matthias; Itkonen, Outi; Konrad, Robert J; Tomosugi, Naohisa; Westerman, Mark; Bansal, Sukhvinder S; Campostrini, Natascia; Drakesmith, Hal; Fillet, Marianne; Olbina, Gordana; Pasricha, Sant-Rayn; Pitts, Kelly R; Sloan, John H; Tagliaro, Franco; Weykamp, Cas W; Swinkels, Dorine W

2016-07-01

Absolute plasma hepcidin concentrations measured by various procedures differ substantially, complicating interpretation of results and rendering reference intervals method dependent. We investigated the degree of equivalence achievable by harmonization and the identification of a commutable secondary reference material to accomplish this goal. We applied technical procedures to achieve harmonization developed by the Consortium for Harmonization of Clinical Laboratory Results. Eleven plasma hepcidin measurement procedures (5 mass spectrometry based and 6 immunochemical based) quantified native individual plasma samples (n = 32) and native plasma pools (n = 8) to assess analytical performance and current and achievable equivalence. In addition, 8 types of candidate reference materials (3 concentrations each, n = 24) were assessed for their suitability, most notably in terms of commutability, to serve as secondary reference material. Absolute hepcidin values and reproducibility (intrameasurement procedure CVs 2.9%-8.7%) differed substantially between measurement procedures, but all were linear and correlated well. The current equivalence (intermeasurement procedure CV 28.6%) between the methods was mainly attributable to differences in calibration and could thus be improved by harmonization with a common calibrator. Linear regression analysis and standardized residuals showed that a candidate reference material consisting of native lyophilized plasma with cryolyoprotectant was commutable for all measurement procedures. Mathematically simulated harmonization with this calibrator resulted in a maximum achievable equivalence of 7.7%. The secondary reference material identified in this study has the potential to substantially improve equivalence between hepcidin measurement procedures and contributes to the establishment of a traceability chain that will ultimately allow standardization of hepcidin measurement results. © 2016 American Association for Clinical Chemistry.

O2 consumption and heart rate in developing zebrafish (Danio rerio): influence of temperature and ambient O2.

PubMed

Barrionuevo, W R; Burggren, W W

1999-02-01

Body mass, length, oxygen consumption (MO2) and heart rate (fH) were measured in "embryos" (prior to hatching), "larvae" (days 10-20), "juveniles" (days 30-70 in 10-day intervals), and "adults" (day 100) of the zebrafish Danio rerio. Fish were chronically reared at either 25, 28, or 31 degreesC and then acutely exposed to hypoxia at different developmental stages. We hypothesized that at any given rearing and measurement temperature, D. rerio would maintain MO2 at lower ambient PO2 [i.e., have a lower critical partial pressure (Pcrit)] as development progressed and that at any given developmental stage individuals reared and measured at higher temperatures would show a more pronounced hypoxic bradycardia. MO2 in normoxic fish at 28 degreesC peaked at approximately 40 micromol. g-1. h-1 at day 10, thereafter falling to 4-5 micromol. g-1. h-1 at day 100. The Q10 for MO2 was 4-5 in embryos, falling to 2-3 from day 10 to day 60 and rising again to 4-5 at day 100. Pcrit at 28 degreesC was approximately 80 mmHg in embryos but decreased sharply to 20 mmHg at 100 days, supporting the hypothesis that more mature fish would be better able to oxygen regulate to lower ambient PO2 levels. Pcrit increased sharply with measurement temperature. Heart rate (fH) at 28 degreesC increased from about 125 beats/min in embryos to a peak of approximately 175 beats/min at days 10-30 and then fell to approximately 130 beats/min by day 100. Unlike for MO2, the Q10 for fH was more constant at 1.2-2.5 throughout development. Hypoxic exposure at any temperature had no effect on fH until approximately day 30, after which time a hypoxic bradycardia was evident. As evident for MO2, the bradycardia in older larvae was more profound at higher temperatures. On the assumption that bradycardia is indicative of hypoxic stress, the increasing prevalence of a hypoxic bradycardia in older, warmer individuals supports the hypothesis that increasing hypoxic susceptibility with development would be exacerbated by increasing temperature. Collectively, these data indicate that the ability to regulate MO2 and fH in response to the compounding demands of increased temperature and/or decreased oxygen availability first develops after approximately 20 days in D. rerio and, thereafter, the ability to maintain MO2 in the face of ambient hypoxia progressively builds through to adulthood. Additionally, the temperature responses of metabolism and heart rate differ substantially at different phases of development, suggesting a loose coupling between the respiratory and cardiovascular systems, at least early in development.

Contact mechanics of modular metal-on-polyethylene total hip replacement under adverse edge loading conditions

PubMed Central

Hua, Xijin; Li, Junyan; Wang, Ling; Jin, Zhongmin; Wilcox, Ruth; Fisher, John

2014-01-01

Edge loading can negatively impact the biomechanics and long-term performance of hip replacements. Although edge loading has been widely investigated for hard-on-hard articulations, limited work has been conducted for hard-on-soft combinations. The aim of the present study was to investigate edge loading and its effect on the contact mechanics of a modular metal-on-polyethylene (MoP) total hip replacement (THR). A three-dimensional finite element model was developed based on a modular MoP bearing. Different cup inclination angles and head lateral microseparation were modelled and their effect on the contact mechanics of the modular MoP hip replacement were examined. The results showed that lateral microseparation caused loading of the head on the rim of the cup, which produced substantial increases in the maximum von Mises stress in the polyethylene liner and the maximum contact pressure on both the articulating surface and backside surface of the liner. Plastic deformation of the liner was observed under both standard conditions and microseparation conditions, however, the maximum equivalent plastic strain in the liner under microseparation conditions of 2000 µm was predicted to be approximately six times that under standard conditions. The study has indicated that correct positioning the components to avoid edge loading is likely to be important clinically even for hard-on-soft bearings for THR. PMID:25218504

The contact mechanics and occurrence of edge loading in modular metal-on-polyethylene total hip replacement during daily activities.

PubMed

Hua, Xijin; Li, Junyan; Jin, Zhongmin; Fisher, John

2016-06-01

The occurrence of edge loading in hip joint replacement has been associated with many factors such as prosthetic design, component malposition and activities of daily living. The present study aimed to quantify the occurrence of edge loading/contact at the articulating surface and to evaluate the effect of cup angles and edge loading on the contact mechanics of a modular metal-on-polyethylene (MoP) total hip replacement (THR) during different daily activities. A three-dimensional finite element model was developed based on a modular MoP bearing system. Different cup inclination and anteversion angles were modelled and six daily activities were considered. The results showed that edge loading was predicted during normal walking, ascending and descending stairs activities under steep cup inclination conditions (≥55°) while no edge loading was observed during standing up, sitting down and knee bending activities. The duration of edge loading increased with increased cup inclination angles and was affected by the cup anteversion angles. Edge loading caused elevated contact pressure at the articulating surface and substantially increased equivalent plastic strain of the polyethylene liner. The present study suggested that correct positioning the component to avoid edge loading that may occur during daily activities is important for MoP THR in clinical practice. Copyright © 2016. Published by Elsevier Ltd.

Determination of palladium and platinum by atomic absorption

USGS Publications Warehouse

Schnepfe, M.M.; Grimaldi, F.S.

1969-01-01

Palladium and platinum are determined by atomic absorption after fire-assay concentration into a gold bead. The limit of determination is ~0??06 ppm in a 20-g sample. Serious depressive interelement interferences are removed by buffering the solutions with a mixture of cadmium and copper sulphates with cadmium and copper concentrations each at 0??5%. Substantial amounts of Ag, Al, Au, Bi, Ca, Co, Cr, Fe, Hg, K, La, Mg, Mn, Mo, Na, Ni, Pb, Te, Ti, V, Y, Zn, and the platinum metals do not interfere in the atomic-absorption determination. ?? 1969.

Compressive creep behavior of alloys based on B2 FeAl

NASA Technical Reports Server (NTRS)

Mantravadi, N.; Vedula, K.; Gaydosh, D.; Titran, R. H.

1986-01-01

Alloys based on FeAl are attractive alternate materials for environmental resistance at intermediate temperatures. Addition of small amounts of Nb, Hf, Ta, Mo, Zr, and B were shown to improve the compressive creep of this alloy at 1100 K. Boron, in particular, was found to have a synergistic effect along with Zr in providing properties substantially better than the binary alloy. This improvement seems to be related to the higher activation energy found for this alloy, suggesting a modification in the diffusion behavior due to the alloying additions.

Compressive creep behavior of alloys based on B2 FeAl

NASA Technical Reports Server (NTRS)

Mantravadi, N.; Vedula, K.; Gaydosh, D.; Titran, R. H.

1987-01-01

Alloys based on FeAl are attractive alternative materials for environmental resistance at intermediate temperatures. Addition of small amounts of Nb, Hf, Ta, Mo, Zr, and B were shown to improve the compressive creep of this alloy at 1100 K. Boron, in particular, was found to have a synergistic effect along with Zr in providing properties substantially better than the binary alloy. This improvement seems to be related to the higher activation energy found for this alloy, suggesting a modification in the diffusion behavior due to the alloying additions.

IL-12 Production Induced by Agaricus blazei Fraction H (ABH) Involves Toll-like Receptor (TLR)

PubMed Central

2004-01-01

Agaricus blazei Murill is an edible fungus used in traditional medicine, which has various well-documented medicinal properties. In the present study, we investigated the effects of hemicellulase-derived mycelia extract (Agaricus blazei fraction H: ABH) on the immune system. First, we examined the cytokine-inducing activity of ABH on human peripheral mononuclear cells (PBMC). The results indicated that ABH induced expression of IL-12, a cytokine known to be a critical regulator of cellular immune responses. Flow cytometric analysis demonstrated the induction of IL-12 production by the CD14-positive cell population, consisting of monocytes/macrophages (Mo/Mφ). Furthermore, the elimination of Mo/Mφ attenuated IL-12 production in PBMC. ABH-induced IL-12 production was inhibited by anti-CD14 and anti-TLR4 antibodies but not by anti-TLR2 antibody. The activity of ABH was not inhibited by polymyxin B, while the activity of lipopolysaccharide used as a reference was inhibited. Oral administration of ABH enhanced natural killer (NK) activity in the spleen. These findings suggest that ABH activated Mo/Mφ in a manner dependent on CD14/TLR4 and NK activity. PMID:15841259

Experimental Verification of the Individual Energy Dependencies of the Partial L-Shell Photoionization Cross Sections of Pd and Mo

NASA Astrophysics Data System (ADS)

Hönicke, Philipp; Kolbe, Michael; Müller, Matthias; Mantler, Michael; Krämer, Markus; Beckhoff, Burkhard

2014-10-01

An experimental method for the verification of the individually different energy dependencies of L1-, L2-, and L3- subshell photoionization cross sections is described. The results obtained for Pd and Mo are well in line with theory regarding both energy dependency and absolute values, and confirm the theoretically calculated cross sections by Scofield from the early 1970 s and, partially, more recent data by Trzhaskovskaya, Nefedov, and Yarzhemsky. The data also demonstrate the questionability of quantitative x-ray spectroscopical results based on the widely used fixed jump ratio approximated cross sections with energy independent ratios. The experiments are carried out by employing the radiometrically calibrated instrumentation of the Physikalisch-Technische Bundesanstalt at the electron storage ring BESSY II in Berlin; the obtained fluorescent intensities are thereby calibrated at an absolute level in reference to the International System of Units. Experimentally determined fixed fluorescence line ratios for each subshell are used for a reliable deconvolution of overlapping fluorescence lines. The relevant fundamental parameters of Mo and Pd are also determined experimentally in order to calculate the subshell photoionization cross sections independently of any database.

Accelerated carrier recombination by grain boundary/edge defects in MBE grown transition metal dichalcogenides

NASA Astrophysics Data System (ADS)

Chen, Ke; Roy, Anupam; Rai, Amritesh; Movva, Hema C. P.; Meng, Xianghai; He, Feng; Banerjee, Sanjay K.; Wang, Yaguo

2018-05-01

Defect-carrier interaction in transition metal dichalcogenides (TMDs) plays important roles in carrier relaxation dynamics and carrier transport, which determines the performance of electronic devices. With femtosecond laser time-resolved spectroscopy, we investigated the effect of grain boundary/edge defects on the ultrafast dynamics of photoexcited carrier in molecular beam epitaxy (MBE)-grown MoTe2 and MoSe2. We found that, comparing with exfoliated samples, the carrier recombination rate in MBE-grown samples accelerates by about 50 times. We attribute this striking difference to the existence of abundant grain boundary/edge defects in MBE-grown samples, which can serve as effective recombination centers for the photoexcited carriers. We also observed coherent acoustic phonons in both exfoliated and MBE-grown MoTe2, indicating strong electron-phonon coupling in this materials. Our measured sound velocity agrees well with the previously reported result of theoretical calculation. Our findings provide a useful reference for the fundamental parameters: carrier lifetime and sound velocity and reveal the undiscovered carrier recombination effect of grain boundary/edge defects, both of which will facilitate the defect engineering in TMD materials for high speed opto-electronics.

A combined experimental and theoretical spectroscopic protocol for determination of the structure of heterogeneous catalysts: developing the information content of the resonance Raman spectra of M1 MoVO x .

PubMed

Kubas, Adam; Noak, Johannes; Trunschke, Annette; Schlögl, Robert; Neese, Frank; Maganas, Dimitrios

2017-09-01

Absorption and multiwavelength resonance Raman spectroscopy are widely used to investigate the electronic structure of transition metal centers in coordination compounds and extended solid systems. In combination with computational methodologies that have predictive accuracy, they define powerful protocols to study the spectroscopic response of catalytic materials. In this work, we study the absorption and resonance Raman spectra of the M1 MoVO x catalyst. The spectra were calculated by time-dependent density functional theory (TD-DFT) in conjunction with the independent mode displaced harmonic oscillator model (IMDHO), which allows for detailed bandshape predictions. For this purpose cluster models with up to 9 Mo and V metallic centers are considered to represent the bulk structure of MoVO x . Capping hydrogens were used to achieve valence saturation at the edges of the cluster models. The construction of model structures was based on a thorough bonding analysis which involved conventional DFT and local coupled cluster (DLPNO-CCSD(T)) methods. Furthermore the relationship of cluster topology to the computed spectral features is discussed in detail. It is shown that due to the local nature of the involved electronic transitions, band assignment protocols developed for molecular systems can be applied to describe the calculated spectral features of the cluster models as well. The present study serves as a reference for future applications of combined experimental and computational protocols in the field of solid-state heterogeneous catalysis.

Effect of ethnicity on first trimester biomarkers for combined trisomy 21 screening: results from a multicenter study in six Asian countries.

PubMed

Manotaya, Saknan; Zitzler, Juergen; Li, Xiaotian; Wibowo, Noroyono; Pham, Thi Mai; Kang, Myung Seo; Lee, Chien-Nan

2015-08-01

To assess differences between first trimester trisomy 21 screening markers free beta chain of the human chorionic gonadotrophin (βhCG) and pregnancy-associated plasma protein A (PAPP-A) in pregnant women of six different Asian countries (China, Indonesia, Korea, Taiwan, Thailand, and Vietnam) and compare serum levels with those in women of European countries. Median and multiple of median (MoM) values of free βhCG and PAPP-A were determined in more than 3000 pregnant women from the Asian countries during their first trimester of pregnancy. Differences in MoM values between a European reference group from a previous multicenter evaluation and the Asian population were evaluated. Two different types of population correction factors for T21 risk estimation were assessed. An at least 10% difference of median MoMs between European and Asian PAPP-A values was found to be statistically significant (p < 0.0001). The specificity of the screening did not show a big difference in individual countries, when using the country-specific correction factor compared with the overall Asian correction factor (<1.4%). The use of a correction factor is recommended based on the differences in European and Asian MoM values. Developing country-specific medians in larger study populations can help identify clinical relevant differences and give the opportunity to explore a more accurate risk calculation. © 2015 John Wiley & Sons, Ltd.

Cubic Dirac fermions in quasi-one-dimensional transition-metal chalcogenide semimetals immune to Peierls distortion

NASA Astrophysics Data System (ADS)

Liu, Qihang; Zunger, Alex

A Cubic Dirac Fermion in condensed-matter physics refers to a band crossing in periodic solids that has 4-fold degeneracy with cubic dispersions in certain directions. Such a crystalline symmetry induced fermion is composed of 6 Weyl fermions where 3 have left-handed and 3 have right-handed chirality, and constitutes one of the ``new fermions'' that have no counterpart in high-energy physics. However, no prediction has yet pointed to a plausible example of a material candidate hosting such a cubically-dispersed Dirac semimetal (CDSM). Here we establish the design principles for CDSM finding that only 2 out of 230 space groups possess the required symmetry elements. Adding the required band occupancy criteria, we conduct a material search using density functional band theory identifying a group of quasi-one-dimensional molybdenum chalcogenide compounds A(MoX)3 (A = Na, K, Rb, In, Tl; X = S, Se, Te) with space group P63/m as ideal CDSM candidates. Studying the stability of the A(MoX)3 family towards a Peierls distortion reveals a few candidates such as Rb(MoTe)3 and Tl(MoTe)3 that are resilliant to Peierls distortion, thus retaining the metallic character. This work was supported by the U.S. Department of Energy, Office of Science, Basic Energy Sciences, Materials Sciences and Engineering Division under Grant No. DE-FG02-13ER46959 to University of Colorado, Boulder.

Cracking vegetable oil from Callophylluminnophyllum L. seeds to bio-gasoline by Ni-Mo/Al2O3 and Ni-Mo/Zeolite as micro-porous catalysts

NASA Astrophysics Data System (ADS)

Savitri, Effendi, R.; Tursiloadi, S.

2016-02-01

Natural minerals such as zeolite are local natural resources in the various regions in Indonesia. Studies on the application of natural mineral currently carried out by national research institutions, among others, as a filler, bleaching agent, or dehydration agent. However, not many studies that utilize these natural minerals as green catalysts material which has high performance for biomass conversion processes and ready to be applied directly by the bio-fuel industry. The trend movement of green and sustainable chemistry research that designing environmentally friendly chemical processes from renewable raw materials to produce innovative products derived biomass for bio-fuel. Callophylluminnophyllum L. seeds can be used as raw material for bio-energy because of its high oil content. Fatty acid and triglyceride compounds from this oil can be cracked into bio-gasoline, which does not contain oxygen in the hydrocarbon structure. Bio-gasoline commonly is referred to as drop-in biofuel because it can be directly used as a substitute fuel. This paper focused on the preparation and formulation of the catalyst NiMo/H-Zeolite and Ni-Mo/Al2O3 which were used in hydro-cracking process of oil from Callophylluminnophyllum L. seeds to produce bio-gasoline. The catalysts were analyzed using XRD, BET and IR-adsorbed pyridine method. The results of hydro-cracking products mostly were paraffin (C10-C19) straight chain, with 59.5 % peak area based on GC-MS analysis.

Leaching behaviour of copper slag, construction and demolition waste and crushed rock used in a full-scale road construction.

PubMed

Lidelöw, Sofia; Mácsik, Josef; Carabante, Ivan; Kumpiene, Jurate

2017-12-15

The leaching behaviour of a road construction with fayalitic copper slag, recycled concrete and crushed rock as sub-base materials was monitored over ten years. All studied materials used in the road construction, including crushed rock, contained concentrations of several elements exceeding the guideline values recommended by the Swedish EPA for total element concentrations for waste materials used in constructions. Despite that, leaching from the road construction under field conditions in general was relatively low. The leachates from the recycled materials contained higher concentrations of several constituents than the leachates from the reference section with crushed rock. The leaching of the elements of interest (Cr, Mo, Ni, Zn) reached peak concentrations during the second and fourth (Cu) years and decreased over the observation period to levels below the Swedish recommended values. Carbonation of the concrete aggregates caused a substantial but short-term increase in the leaching of oxyanions such as chromate. The environmental risks related to element leaching are highest at the beginning of the road life. Ageing of materials or pre-treatment through leaching is needed prior to their use in construction to avoid peak concentrations. Also, the design of road constructions should be adjusted so that recycled materials are covered with low-permeability covers, which would minimize the exposure to atmospheric precipitation and weathering. Copyright © 2017 Elsevier Ltd. All rights reserved.

Gait and Cognition in Parkinson's Disease: Cognitive Impairment Is Inadequately Reflected by Gait Performance during Dual Task.

PubMed

Gaßner, Heiko; Marxreiter, Franz; Steib, Simon; Kohl, Zacharias; Schlachetzki, Johannes C M; Adler, Werner; Eskofier, Bjoern M; Pfeifer, Klaus; Winkler, Jürgen; Klucken, Jochen

2017-01-01

Cognitive and gait deficits are common symptoms in Parkinson's disease (PD). Motor-cognitive dual tasks (DTs) are used to explore the interplay between gait and cognition. However, it is unclear if DT gait performance is indicative for cognitive impairment. Therefore, the aim of this study was to investigate if cognitive deficits are reflected by DT costs of spatiotemporal gait parameters. Cognitive function, single task (ST) and DT gait performance were investigated in 67 PD patients. Cognition was assessed by the Montreal Cognitive Assessment (MoCA) followed by a standardized, sensor-based gait test and the identical gait test while subtracting serial 3's. Cognitive impairment was defined by a MoCA score <26. DT costs in gait parameters [(DT - ST)/ST × 100] were calculated as a measure of DT effect on gait. Correlation analysis was used to evaluate the association between MoCA performance and gait parameters. In a linear regression model, DT gait costs and clinical confounders (age, gender, disease duration, motor impairment, medication, and depression) were correlated to cognitive performance. In a subgroup analysis, we compared matched groups of cognitively impaired and unimpaired PD patients regarding differences in ST, DT, and DT gait costs. Correlation analysis revealed weak correlations between MoCA score and DT costs of gait parameters ( r / r Sp  ≤ 0.3). DT costs of stride length, swing time variability, and maximum toe clearance (| r / r Sp | > 0.2) were included in a regression analysis. The parameters only explain 8% of the cognitive variance. In combination with clinical confounders, regression analysis showed that these gait parameters explained 30% of MoCA performance. Group comparison revealed strong DT effects within both groups (large effect sizes), but significant between-group effects in DT gait costs were not observed. These findings suggest that DT gait performance is not indicative for cognitive impairment in PD. DT effects on gait parameters were substantial in cognitively impaired and unimpaired patients, thereby potentially overlaying the effect of cognitive impairment on DT gait costs. Limits of the MoCA in detecting motor-function specific cognitive performance or variable individual response to the DT as influencing factors cannot be excluded. Therefore, DT gait parameters as marker for cognitive performance should be carefully interpreted in the clinical context.

Positional reference system for ultraprecision machining

DOEpatents

Arnold, Jones B.; Burleson, Robert R.; Pardue, Robert M.

1982-01-01

A stable positional reference system for use in improving the cutting tool-to-part contour position in numerical controlled-multiaxis metal turning machines is provided. The reference system employs a plurality of interferometers referenced to orthogonally disposed metering bars which are substantially isolated from machine strain induced position errors for monitoring the part and tool positions relative to the metering bars. A microprocessor-based control system is employed in conjunction with the plurality of position interferometers and part contour description data inputs to calculate error components for each axis of movement and output them to corresponding axis drives with appropriate scaling and error compensation. Real-time position control, operating in combination with the reference system, makes possible the positioning of the cutting points of a tool along a part locus with a substantially greater degree of accuracy than has been attained previously in the art by referencing and then monitoring only the tool motion relative to a reference position located on the machine base.

Positional reference system for ultraprecision machining

DOEpatents

Arnold, J.B.; Burleson, R.R.; Pardue, R.M.

1980-09-12

A stable positional reference system for use in improving the cutting tool-to-part contour position in numerical controlled-multiaxis metal turning machines is provided. The reference system employs a plurality of interferometers referenced to orthogonally disposed metering bars which are substantially isolated from machine strain induced position errors for monitoring the part and tool positions relative to the metering bars. A microprocessor-based control system is employed in conjunction with the plurality of positions interferometers and part contour description data input to calculate error components for each axis of movement and output them to corresponding axis driven with appropriate scaling and error compensation. Real-time position control, operating in combination with the reference system, makes possible the positioning of the cutting points of a tool along a part locus with a substantially greater degree of accuracy than has been attained previously in the art by referencing and then monitoring only the tool motion relative to a reference position located on the machine base.

Troglomorphic sculpins of the Cottus carolinae species group in Perry County, Missouri: distribution, external morphology, and conservation status

Treesearch

Brooks M. Burr; Ginny L. Adams; Jean K. Krejca; Regina J. Paul; Melvin L. Warren

2001-01-01

The existence of cavernicolous sculpin (here allocated to Cottus carolinae, banded sculpin, and referred to as grotto sculpin), in the karst regions of Perry County, MO, first came to our attention in 1991. Examination of 35 caves in Missouri, 96 in Illinois, 17 in Tennessee, 2 in Indiana, and 11 in Arkansas revealed that banded sculpin are common in...

Faster Forgetting Contributes to Impaired Spatial Memory in the PDAPP Mouse: Deficit in Memory Retrieval Associated with Increased Sensitivity to Interference?

ERIC Educational Resources Information Center

Daumas, Stephanie; Sandin, Johan; Chen, Karen S.; Kobayashi, Dione; Tulloch, Jane; Martin, Stephen J.; Games, Dora; Morris, Richard G. M.

2008-01-01

Two experiments were conducted to investigate the possibility of faster forgetting by PDAPP mice (a well-established model of Alzheimer's disease as reported by Games and colleagues in an earlier paper). Experiment 1, using mice aged 13-16 mo, confirmed the presence of a deficit in a spatial reference memory task in the water maze by hemizygous…

The Role of Microstructure on Various Stages of the Very High Cycle Fatigue Behavior of an a + Beta Titanium Alloy, Ti-6Al-2Sn-4Zr-6Mo (Preprint)

DTIC Science & Technology

2011-10-01

microtextured regions and the majority of α phase material (lath α and equiaxed αp) is oriented for slip on basal and prism planes. LeBiavant et al ...appreciated. REFERENCES [1] Mughrabi , H.: On the life-controlling microstructural fatigue mechanisms in ductile metals and alloys in the

Autogenic reaction synthesis of photocatalysts for solar fuel generation

DOEpatents

Ingram, Brian J.; Pol, Vilas G.; Cronauer, Donald C.; Ramanathan, Muruganathan

2016-04-19

In one preferred embodiment, a photocatalyst for conversion of carbon dioxide and water to a hydrocarbon and oxygen comprises at least one nanoparticulate metal or metal oxide material that is substantially free of a carbon coating, prepared by heating a metal-containing precursor compound in a sealed reactor under a pressure autogenically generated by dissociation of the precursor material in the sealed reactor at a temperature of at least about 600.degree. C. to form a nanoparticulate carbon-coated metal or metal oxide material, and subsequently substantially removing the carbon coating. The precursor material comprises a solid, solvent-free salt comprising a metal ion and at least one thermally decomposable carbon- and oxygen-containing counter-ion, and the metal of the salt is selected from the group consisting of Mn, Ti, Sn, V, Fe, Zn, Zr, Mo, Nb, W, Eu, La, Ce, In, and Si.

Patterns of language and auditory dysfunction in 6-year-old children with epilepsy.

PubMed

Selassie, Gunilla Rejnö-Habte; Olsson, Ingrid; Jennische, Margareta

2009-01-01

In a previous study we reported difficulty with expressive language and visuoperceptual ability in preschool children with epilepsy and otherwise normal development. The present study analysed speech and language dysfunction for each individual in relation to epilepsy variables, ear preference, and intelligence in these children and described their auditory function. Twenty 6-year-old children with epilepsy (14 females, 6 males; mean age 6:5 y, range 6 y-6 y 11 mo) and 30 reference children without epilepsy (18 females, 12 males; mean age 6:5 y, range 6 y-6 y 11 mo) were assessed for language and auditory ability. Low scores for the children with epilepsy were analysed with respect to speech-language domains, type of epilepsy, site of epileptiform activity, intelligence, and language laterality. Auditory attention, perception, discrimination, and ear preference were measured with a dichotic listening test, and group comparisons were performed. Children with left-sided partial epilepsy had extensive language dysfunction. Most children with partial epilepsy had phonological dysfunction. Language dysfunction was also found in children with generalized and unclassified epilepsies. The children with epilepsy performed significantly worse than the reference children in auditory attention, perception of vowels and discrimination of consonants for the right ear and had more left ear advantage for vowels, indicating undeveloped language laterality.

Changes in glomerular parietal epithelial cells in mouse kidneys with advanced age

PubMed Central

Roeder, Sebastian S.; Stefanska, Ania; Eng, Diana G.; Kaverina, Natalya; Sunseri, Maria W.; McNicholas, Bairbre A.; Rabinovitch, Peter; Engel, Felix B.; Daniel, Christoph; Amann, Kerstin; Lichtnekert, Julia; Pippin, Jeffrey W.

2015-01-01

Kidney aging is accompanied by characteristic changes in the glomerulus, but little is known about the effect of aging on glomerular parietal epithelial cells (PECs), nor if the characteristic glomerular changes in humans and rats also occur in very old mice. Accordingly, a descriptive analysis was undertaken in 27-mo-old C57B6 mice, considered advanced age. PEC density was significantly lower in older mice compared with young mice (aged 3 mo), and the decrease was more pronounced in juxtamedullary glomeruli compared with outer cortical glomeruli. In addition to segmental and global glomerulosclerosis in older mice, staining for matrix proteins collagen type IV and heparan sulfate proteoglycan were markedly increased in Bowman's capsules of older mouse glomeruli, consistent with increased extracellular matrix production by PECs. De novo staining for CD44, a marker of activated and profibrotic PECs, was significantly increased in aged glomeruli. CD44 staining was more pronounced in the juxtamedullary region and colocalized with phosphorylated ERK. Additionally, a subset of aged PECs de novo expressed the epithelial-to-mesenchymal transition markers α-smooth muscle and vimentin, with no changes in epithelial-to-mesenchymal transition markers E-cadherin and β-catenin. The mural cell markers neural/glial antigen 2, PDGF receptor-β, and CD146 as well as Notch 3 were also substantially increased in aged PECs. These data show that mice can be used to better understand the aging kidney and that PECs undergo substantial changes, especially in juxtamedullary glomeruli, that may participate in the overall decline in glomerular structure and function with advancing age. PMID:26017974

Critical windows for nutritional interventions against stunting.

PubMed

Prentice, Andrew M; Ward, Kate A; Goldberg, Gail R; Jarjou, Landing M; Moore, Sophie E; Fulford, Anthony J; Prentice, Ann

2013-05-01

An analysis of early growth patterns in children from 54 resource-poor countries in Africa and Southeast Asia shows a rapid falloff in the height-for-age z score during the first 2 y of life and no recovery until ≥5 y of age. This finding has focused attention on the period -9 to 24 mo as a window of opportunity for interventions against stunting and has garnered considerable political backing for investment targeted at the first 1000 d. These important initiatives should not be undermined, but the objective of this study was to counteract the growing impression that interventions outside of this period cannot be effective. We illustrate our arguments using longitudinal data from the Consortium of Health Oriented Research in Transitioning collaboration (Brazil, Guatemala, India, Philippines, and South Africa) and our own cross-sectional and longitudinal growth data from rural Gambia. We show that substantial height catch-up occurs between 24 mo and midchildhood and again between midchildhood and adulthood, even in the absence of any interventions. Longitudinal growth data from rural Gambia also illustrate that an extended pubertal growth phase allows very considerable height recovery, especially in girls during adolescence. In light of the critical importance of maternal stature to her children's health, our arguments are a reminder of the importance of the more comprehensive UNICEF/Sub-Committee on Nutrition Through the Life-Cycle approach. In particular, we argue that adolescence represents an additional window of opportunity during which substantial life cycle and intergenerational effects can be accrued. The regulation of such growth is complex and may be affected by nutritional interventions imposed many years previously.

Porous p-NiO/n-Nb2O5 nanocomposites prepared by an EISA route with enhanced photocatalytic activity in simultaneous Cr(VI) reduction and methyl orange decolorization under visible light irradiation.

PubMed

Hashemzadeh, Fatemeh; Gaffarinejad, Ali; Rahimi, Rahmatollah

2015-04-09

Porous NiO/Nb2O5 nanocomposites with Ni/Nb molar ratio of 0.4, 0.8 and 1.2 have been obtained via the EISA route using P123 copolymer as organic template, and are assigned as NiNb0.4, NiNb0.8 and NiNb1.2, respectively. For comparison, pure Nb2O5 sample assigned as NiNb0.0 was also synthesized by the same method. Structural and textural features of the as prepared samples were investigated by XRD, FTIR, FE-SEM, EDX, UV-vis DRS and BET techniques. The results indicated that the porous p-NiO/n-Nb2O5 junction nanocomposites were formed and coupling of NiO with Nb2O5 resulted a remarkable red shift in the optical response of the nanocomposite samples. The photocatalytic properties of the nanocomposite samples, and also synthesized pure Nb2O5 (NiNb0.0) and commercial Nb2O5 as reference catalysts were evaluated for the first time by simultaneous Cr(VI) reduction and MO decolorization in aqueous suspension under visible light irradiation at pH 2. NiNb0.4 was found to be the most active photocatalyst, which might be attributed to the extended absorption in the visible light region and the effective photogenerated electron-hole separation by the photosynergistic effects of the p-NiO/n-Nb2O5 composite powder. The photocatalytic efficiency of the most active photocatalyst, NiNb0.4, was found to be rather low for either single Cr(VI) solution or single MO solution. However, the photocatalytic reduction of Cr(VI) and photocatalytic decolorization of MO proceed more rapidly for the coexistence system of Cr(VI) and MO than for the single process, showing synergetic effect between the reduction and decolorization reactions. The effects of initial concentration of Cr(VI), MO and the initial pH value on the rate of simultaneous photoreactions over NiNb0.4 sample, were also investigated. The Cr(VI) and MO removal rates were further enhanced by increasing MO and Cr (VI) concentration to an optimal value, respectively, and/or decreasing solution pH. Copyright © 2014 Elsevier B.V. All rights reserved.

Valuing hydrological alteration in Multi-Objective reservoir management

NASA Astrophysics Data System (ADS)

Bizzi, S.; Pianosi, F.; Soncini-Sessa, R.

2012-04-01

Water management through dams and reservoirs is worldwide necessary to support key human-related activities ranging from hydropower production to water allocation for agricultural production, and flood risk mitigation. Advances in multi-objectives (MO) optimization techniques and ever growing computing power make it possible to design reservoir operating policies that represent Pareto-optimal tradeoffs between the multiple interests analysed. These progresses if on one hand are likely to enhance performances of commonly targeted objectives (such as hydropower production or water supply), on the other risk to strongly penalize all the interests not directly (i.e. mathematically) optimized within the MO algorithm. Alteration of hydrological regime, although is a well established cause of ecological degradation and its evaluation and rehabilitation are commonly required by recent legislation (as the Water Framework Directive in Europe), is rarely embedded as an objective in MO planning of optimal releases from reservoirs. Moreover, even when it is explicitly considered, the criteria adopted for its evaluation are doubted and not commonly trusted, undermining the possibility of real implementation of environmentally friendly policies. The main challenges in defining and assessing hydrological alterations are: how to define a reference state (referencing); how to define criteria upon which to build mathematical indicators of alteration (measuring); and finally how to aggregate the indicators in a single evaluation index that can be embedded in a MO optimization problem (valuing). This paper aims to address these issues by: i) discussing benefits and constrains of different approaches to referencing, measuring and valuing hydrological alteration; ii) testing two alternative indices of hydrological alteration in the context of MO problems, one based on the established framework of Indices of Hydrological Alteration (IHA, Richter et al., 1996), and a novel satisfying the mathematical properties required by widely used optimization methods based on dynamic programming; iii) discussing the ranking provided by the proposed indices for a case study in Italy where different operating policies were designed using a MO algorithm, taking into account hydropower production, irrigation supply and flood mitigation and imposing different type of minimum environmental flow; iv) providing a framework to effectively include hydrological alteration within MO problem of reservoir management. Richter, B.D., Baumgartner, J.V., Powell, J., Braun, D.P., 1996, A Method for Assessing Hydrologic Alteration within Ecosystems, Conservation Biology, 10(4), 1163-1174.

NeMO-Net & Fluid Lensing: The Neural Multi-Modal Observation & Training Network for Global Coral Reef Assessment Using Fluid Lensing Augmentation of NASA EOS Data

NASA Technical Reports Server (NTRS)

Chirayath, Ved

2018-01-01

We present preliminary results from NASA NeMO-Net, the first neural multi-modal observation and training network for global coral reef assessment. NeMO-Net is an open-source deep convolutional neural network (CNN) and interactive active learning training software in development which will assess the present and past dynamics of coral reef ecosystems. NeMO-Net exploits active learning and data fusion of mm-scale remotely sensed 3D images of coral reefs captured using fluid lensing with the NASA FluidCam instrument, presently the highest-resolution remote sensing benthic imaging technology capable of removing ocean wave distortion, as well as hyperspectral airborne remote sensing data from the ongoing NASA CORAL mission and lower-resolution satellite data to determine coral reef ecosystem makeup globally at unprecedented spatial and temporal scales. Aquatic ecosystems, particularly coral reefs, remain quantitatively misrepresented by low-resolution remote sensing as a result of refractive distortion from ocean waves, optical attenuation, and remoteness. Machine learning classification of coral reefs using FluidCam mm-scale 3D data show that present satellite and airborne remote sensing techniques poorly characterize coral reef percent living cover, morphology type, and species breakdown at the mm, cm, and meter scales. Indeed, current global assessments of coral reef cover and morphology classification based on km-scale satellite data alone can suffer from segmentation errors greater than 40%, capable of change detection only on yearly temporal scales and decameter spatial scales, significantly hindering our understanding of patterns and processes in marine biodiversity at a time when these ecosystems are experiencing unprecedented anthropogenic pressures, ocean acidification, and sea surface temperature rise. NeMO-Net leverages our augmented machine learning algorithm that demonstrates data fusion of regional FluidCam (mm, cm-scale) airborne remote sensing with global low-resolution (m, km-scale) airborne and spaceborne imagery to reduce classification errors up to 80% over regional scales. Such technologies can substantially enhance our ability to assess coral reef ecosystems dynamics.

7Li-induced reaction on natMo: A study of complete versus incomplete fusion

NASA Astrophysics Data System (ADS)

Kumar, Deepak; Maiti, Moumita; Lahiri, Susanta

2017-07-01

Background: Several investigations on the complete-incomplete fusion (CF-ICF) dynamics of α -cluster well-bound nuclei have been contemplated above the Coulomb barrier (˜4 -7 MeV/nucleon) in recent years. It is therefore expected to observe significant ICF over CF in the reactions induced by a weakly bound α -cluster nucleus at slightly above the barrier. Purpose: Study of the CF-ICF dynamics by measuring the populated residues in the weakly bound 7Li+natMo system at energies slightly above the Coulomb barrier to well above it. Method: In order to investigate CF-ICF in the loosely bound system, 7Li beam was bombarded on the natMo foils, separated by the aluminium (Al) catcher foils alternatively, within ˜3 -6.5 MeV/nucleon. Evaporation residues produced in each foil were identified by the off-line γ -ray spectrometry. Measured cross section data of the residues were compared with the theoretical model calculations based on the equilibrium (EQ) and pre-equilibrium (PEQ) reaction mechanisms. Results: The experimental cross section of Rh 101 m,100 ,99 m,97 ,Ru,9597,Tc 99 m,96 ,95 ,94 ,93 m+g , and 93mMo residues measured at various projectile energies were satisfactorily reproduced by the simplified coupled channel approach in comparison to single barrier penetration model calculation. Significant cross section enhancement in the α -emitting channels was observed compared to EQ and PEQ model calculations throughout observed energy region. The ICF process over CF was analyzed by comparing with EMPIRE. The increment of the incomplete fusion fraction was observed with increasing projectile energies. Conclusions: Theoretical model calculations reveal that the compound reaction mechanism is the major contributor to the production of residues in 7Li+natMo reaction. Theoretical evaluations substantiate the contribution of ICF over the CF in α -emitting channels. EMPIRE estimations shed light on its predictive capability of cross sections of the residues from the heavy-ion induced reactions.

Monoclonal Antibodies Radiolabeling with Rhenium-188 for Radioimmunotherapy

PubMed Central

Martini, Petra; Pasquali, Micol

2017-01-01

Rhenium-188, obtained from an alumina-based tungsten-188/rhenium-188 generator, is actually considered a useful candidate for labeling biomolecules such as antibodies, antibody fragments, peptides, and DNAs for radiotherapy. There is a widespread interest in the availability of labeling procedures that allow obtaining 188Re-labeled radiopharmaceuticals for various therapeutic applications, in particular for the rhenium attachment to tumor-specific monoclonal antibodies (Mo)Abs for immunotherapy. Different approaches have been developed in order to obtain 188Re-radioimmunoconjugates in high radiochemical purity starting from the generator eluted [188Re]ReO4−. The aim of this paper is to provide a short overview on 188Re-labeled (Mo)Abs, focusing in particular on the radiolabeling methods, quality control of radioimmunoconjugates, and their in vitro stability for radioimmunotherapy (RIT), with particular reference to the most important contributions published in literature in this topic. PMID:28951872

Effect of education and gender adjustment on the sensitivity and specificity of a cognitive screening battery for dementia: results from the MoVIES Project. Monongahela Valley Independent Elders Survey.

PubMed

Belle, S H; Seaberg, E C; Ganguli, M; Ratcliff, G; DeKosky, S; Kuller, L H

1996-01-01

The Monongahela Valley Independent Elders Survey (MoVIES) used a multiphase process to identify demented persons among 1,366 randomly selected noninstitutionalized individuals 65 years and older. Raw test scores from a cognitive screening battery were used to identify cognitively impaired individuals who were referred for a clinical evaluation. Subsequently, test scores were adjusted for education and gender within age strata. Adjusting test scores affected sensitivity for dementia only among the most educated, increasing sensitivity among younger subjects and decreasing among the older subjects. Specificity increased among the least educated and the oldest subjects. Overall, the adjusted criteria did not perform as well as the unadjusted criteria in this sample. Adjustment for education will not necessarily improve the ability of a screening battery for cognitive function to identify demented persons, particularly if unadjusted scores perform well.

Monoclonal Antibodies Radiolabeling with Rhenium-188 for Radioimmunotherapy.

PubMed

Uccelli, Licia; Martini, Petra; Pasquali, Micol; Boschi, Alessandra

2017-01-01

Rhenium-188, obtained from an alumina-based tungsten-188/rhenium-188 generator, is actually considered a useful candidate for labeling biomolecules such as antibodies, antibody fragments, peptides, and DNAs for radiotherapy. There is a widespread interest in the availability of labeling procedures that allow obtaining 188 Re-labeled radiopharmaceuticals for various therapeutic applications, in particular for the rhenium attachment to tumor-specific monoclonal antibodies (Mo)Abs for immunotherapy. Different approaches have been developed in order to obtain 188 Re-radioimmunoconjugates in high radiochemical purity starting from the generator eluted [ 188 Re]ReO 4 - . The aim of this paper is to provide a short overview on 188 Re-labeled (Mo)Abs, focusing in particular on the radiolabeling methods, quality control of radioimmunoconjugates, and their in vitro stability for radioimmunotherapy (RIT), with particular reference to the most important contributions published in literature in this topic.

Effect of telemedicine on glycated hemoglobin in diabetes: a systematic review and meta-analysis of randomized trials

PubMed Central

Faruque, Labib Imran; Wiebe, Natasha; Ehteshami-Afshar, Arash; Liu, Yuanchen; Dianati-Maleki, Neda; Hemmelgarn, Brenda R.; Manns, Braden J.; Tonelli, Marcello

2017-01-01

BACKGROUND: Telemedicine, the use of telecommunications to deliver health services, expertise and information, is a promising but unproven tool for improving the quality of diabetes care. We summarized the effectiveness of different methods of telemedicine for the management of diabetes compared with usual care. METHODS: We searched MEDLINE, Embase and the Cochrane Central Register of Controlled Trials databases (to November 2015) and reference lists of existing systematic reviews for randomized controlled trials (RCTs) comparing telemedicine with usual care for adults with diabetes. Two independent reviewers selected the studies and assessed risk of bias in the studies. The primary outcome was glycated hemoglobin (HbA1C) reported at 3 time points (≤ 3 mo, 4–12 mo and > 12 mo). Other outcomes were quality of life, mortality and episodes of hypoglycemia. Trials were pooled using randomeffects meta-analysis, and heterogeneity was quantified using the I2 statistic. RESULTS: From 3688 citations, we identified 111 eligible RCTs (n = 23 648). Telemedicine achieved significant but modest reductions in HbA1C in all 3 follow-up periods (difference in mean at ≤ 3 mo: −0.57%, 95% confidence interval [CI] −0.74% to −0.40% [39 trials]; at 4–12 mo: −0.28%, 95% CI −0.37% to −0.20% [87 trials]; and at > 12 mo: −0.26%, 95% CI −0.46% to −0.06% [5 trials]). Quantified heterogeneity (I2 statistic) was 75%, 69% and 58%, respectively. In meta-regression analyses, the effect of telemedicine on HbA1C appeared greatest in trials with higher HbA1C concentrations at baseline, in trials where providers used Web portals or text messaging to communicate with patients and in trials where telemedicine facilitated medication adjustment. Telemedicine had no convincing effect on quality of life, mortality or hypoglycemia. INTERPRETATION: Compared with usual care, the addition of telemedicine, especially systems that allowed medication adjustments with or without text messaging or a Web portal, improved HbA1C but not other clinically relevant outcomes among patients with diabetes. PMID:27799615

Effect of telemedicine on glycated hemoglobin in diabetes: a systematic review and meta-analysis of randomized trials.

PubMed

Faruque, Labib Imran; Wiebe, Natasha; Ehteshami-Afshar, Arash; Liu, Yuanchen; Dianati-Maleki, Neda; Hemmelgarn, Brenda R; Manns, Braden J; Tonelli, Marcello

2017-03-06

Telemedicine, the use of telecommunications to deliver health services, expertise and information, is a promising but unproven tool for improving the quality of diabetes care. We summarized the effectiveness of different methods of telemedicine for the management of diabetes compared with usual care. We searched MEDLINE, Embase and the Cochrane Central Register of Controlled Trials databases (to November 2015) and reference lists of existing systematic reviews for randomized controlled trials (RCTs) comparing telemedicine with usual care for adults with diabetes. Two independent reviewers selected the studies and assessed risk of bias in the studies. The primary outcome was glycated hemoglobin (HbA 1C ) reported at 3 time points (≤ 3 mo, 4-12 mo and > 12 mo). Other outcomes were quality of life, mortality and episodes of hypoglycemia. Trials were pooled using randomeffects meta-analysis, and heterogeneity was quantified using the I 2 statistic. From 3688 citations, we identified 111 eligible RCTs ( n = 23 648). Telemedicine achieved significant but modest reductions in HbA 1C in all 3 follow-up periods (difference in mean at ≤ 3 mo: -0.57%, 95% confidence interval [CI] -0.74% to -0.40% [39 trials]; at 4-12 mo: -0.28%, 95% CI -0.37% to -0.20% [87 trials]; and at > 12 mo: -0.26%, 95% CI -0.46% to -0.06% [5 trials]). Quantified heterogeneity ( I 2 statistic) was 75%, 69% and 58%, respectively. In meta-regression analyses, the effect of telemedicine on HbA 1C appeared greatest in trials with higher HbA 1C concentrations at baseline, in trials where providers used Web portals or text messaging to communicate with patients and in trials where telemedicine facilitated medication adjustment. Telemedicine had no convincing effect on quality of life, mortality or hypoglycemia. Compared with usual care, the addition of telemedicine, especially systems that allowed medication adjustments with or without text messaging or a Web portal, improved HbA 1C but not other clinically relevant outcomes among patients with diabetes. © 2017 Canadian Medical Association or its licensors.

Geochemical element mobility during the hydrothermal alteration in the Tepeoba porphyry Cu-Mo-Au deposits at Balikesir, NW Turkey

NASA Astrophysics Data System (ADS)

Abdelnasser, Amr; Kiran Yildirim, Demet; Doner, Zeynep; Kumral, Mustafa

2016-04-01

The Tepeoba porphyry Cu-Mo-Au deposit represents one of the important copper source and mineral deposits in the Anatolian tectonic belt at Balikesir province, NW Turkey. It considered as a vein-type deposit locally associated with intense hydrothermal alteration within the brecciation, quartz stockwork veining, and brittle fracture zones in the main host rock that represented by hornfels, as well as generally related to the shallow intermediate to silicic intrusive Eybek pluton. Based on the field and geologic relationships and types of ore mineral assemblages and the accompanied alteration types, there are two mineralization zones; hypogene (primary) and oxidation/supergene zones are observed associated with three alteration zones; potassic, phyllic, and propylitic zones related to this porphyry deposit. The phyllic and propylitic alterations locally surrounded the potassic alteration. The ore minerals related to the hypogene zone represented by mostly chalcopyrite, Molybdenite, and pyrite with subordinate amount of marcasite, enargite, and gold. On the other hand they include mainly cuprite with chalcopyrite, pyrite and gold as well as hematite and goethite at the oxidation/supergene zone. This study deals with the quantitative calculations of the mass/volume changes (gains and losses) of the major and trace elements during the different episodes of alteration in this porphyry deposit. These mass balance data reveal that the potassic alteration zone that the main Cu- and Mo-enriched zone, has enrichment of K, Si, Fe, and Mg, and depletion of Na referring to replacement of plagioclase and amphibole by K-feldspar, sericite and biotite. While the propylitic alteration that is the main Mo- and Au-enriched zone is accompanied with K and Na depletion with enrichment of Si, Fe, Mg, and Ca forming chlorite, epidote, carbonate and pyrite. On the other hand the phyllic alteration that occurred in the outer part around the potassic alteration, characterized by less amount of Cu and Mo mineralization having addition of Si and K with removal of Fe, Mg, Ca, and Na. Keywords: Mass balance calculation; Tepeoba porphyry Cu-Mo-Au deposits; Balikesir; Turkey

Method for fabricating .sup.99 Mo production targets using low enriched uranium, .sup.99 Mo production targets comprising low enriched uranium

DOEpatents

Wiencek, Thomas C.; Matos, James E.; Hofman, Gerard L.

1997-01-01

A radioisotope production target and a method for fabricating a radioisotope production target is provided, wherein the target comprises an inner cylinder, a foil of fissionable material circumferentially contacting the outer surface of the inner cylinder, and an outer hollow cylinder adapted to receive the substantially foil-covered inner cylinder and compress tightly against the foil to provide good mechanical contact therewith. The method for fabricating a primary target for the production of fission products comprises preparing a first substrate to receive a foil of fissionable material so as to allow for later removal of the foil from the first substrate, preparing a second substrate to receive the foil so as to allow for later removal of the foil from the second substrate; attaching the first substrate to the second substrate such that the foil is sandwiched between the first substrate and second substrate to prevent foil exposure to ambient atmosphere, and compressing the exposed surfaces of the first and second substrate to assure snug mechanical contact between the foil, the first substrate and the second substrate.

Method for fabricating .sup.99 Mo production targets using low enriched uranium, .sup.99 Mo production targets comprising low enriched uranium

DOEpatents

Wiencek, Thomas C [Orland Park, IL; Matos, James E [Oak Park, IL; Hofman, Gerard L [Downers Grove, IL

2000-12-12

A radioisotope production target and a method for fabricating a radioisotope production target is provided, wherein the target comprises an inner cylinder, a foil of fissionable material circumferentially contacting the outer surface of the inner cylinder, and an outer hollow cylinder adapted to receive the substantially foil-covered inner cylinder and compress tightly against the foil to provide good mechanical contact therewith. The method for fabricating a primary target for the production of fission products comprises preparing a first substrate to receive a foil of fissionable material so as to allow for later removal of the foil from the first substrate, preparing a second substrate to receive the foil so as to allow for later removal of the foil from the second substrate; attaching the first substrate to the second substrate such that the foil is sandwiched between the first substrate and second substrate to prevent foil exposure to ambient atmosphere, and compressing the exposed surfaces of the first and second substrate to assure snug mechanical contact between the foil, the first substrate and the second substrate.

Effect of in-pile degradation of the meat thermal conductivity on the maximum temperature of the plate-type U-Mo dispersion fuels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pavel G. Medvedev

2009-11-01

Effect of in-pile degradation of thermal conductivity on the maximum temperature of the plate-type research reactor fuels has been assessed using the steady-state heat conduction equation and assuming convection cooling. It was found that due to very low meat thickness, characteristic for this type of fuel, the effect of thermal conductivity degradation on the maximum fuel temperature is minor. For example, the fuel plate featuring 0.635 mm thick meat operating at heat flux of 600 W/cm2 would experience only a 20oC temperature rise if the meat thermal conductivity degrades from 0.8 W/cm-s to 0.3 W/cm-s. While degradation of meat thermalmore » conductivity in dispersion-type U-Mo fuel can be very substantial due to formation of interaction layer between the particles and the matrix, and development of fission gas filled porosity, this simple analysis demonstrates that this phenomenon is unlikely to significantly affect the temperature-based safety margin of the fuel during normal operation.« less

An Integrated Computational and Experimental Approach Toward the Design of Materials for Fuel Cell Systems

DTIC Science & Technology

2012-10-01

13 Based on the limited work done, the best reported ORR chalcogenide electrocatalysts for PEMFC applications can be ranked as follows: MoRuSe... PEMFC catalysts is the durability of the catalyst particles. Particle size distribution tends to shift towards larger particles during the...the design of new materials for applications in PEMFCs . Reference: A more detailed treatment of the topics of this section, Experimental Target 11

Theory, Methods, and Applications of Nonlinear Control

DTIC Science & Technology

2012-08-29

an application to Lotka - Volterra systems,” in Proceedings of the American Control Conference (St. Louis, MO, 10-12 June 2009), pp. 96-101. [MM10a...Mazenc, F., and M. Malisoff, “Strict Lyapunov function constructions under LaSalle conditions with an application to Lotka - Volterra systems,” IEEE...the tracking dynamics, (d) the applicability of the theory to a very general class of reference trajectories, and (e) the use of input-to-state

Surface Tension Components Based Selection of Cosolvents for Efficient Liquid Phase Exfoliation of 2D Materials.

PubMed

Shen, Jianfeng; Wu, Jingjie; Wang, Man; Dong, Pei; Xu, Jingxuan; Li, Xiaoguang; Zhang, Xiang; Yuan, Junhua; Wang, Xifan; Ye, Mingxin; Vajtai, Robert; Lou, Jun; Ajayan, Pulickel M

2016-05-01

A proper design of direct liquid phase exfoliation (LPE) for 2D materials as graphene, MoS2 , WS2 , h-BN, Bi2 Se3 , MoSe2 , SnS2 , and TaS2 with common cosolvents is carried out based on considering the polar and dispersive components of surface tensions of various cosolvents and 2D materials. It has been found that the exfoliation efficiency is enhanced by matching the ratio of surface tension components of cosolvents to that of the targeted 2D materials, based on which common cosolvents composed of IPA/water, THF/water, and acetone/water can be designed for sufficient LPE process. In this context, the library of low-toxic and low-cost solvents with low boiling points for LPE is infinitely enlarged when extending to common cosolvents. Polymer-based composites reinforced with a series of different 2D materials are compared with each other. It is demonstrated that the incorporation of cosolvents-exfoliated 2D materials can substantially improve the mechanical and thermal properties of polymer matrices. Typically, with the addition of 0.5 wt% of such 2D material as MoS2 nanosheets, the tensile strength and Young's modulus increased up to 74.85% and 136.97%, respectively. The different enhancement effect of 2D materials is corresponded to the intrinsic properties and LPE capacity of 2D materials. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Four-point Bend Testing of Irradiated Monolithic U-10Mo Fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rabin, B. H.; Lloyd, W. R.; Schulthess, J. L.

2015-03-01

This paper presents results of recently completed studies aimed at characterizing the mechanical properties of irradiated U-10Mo fuel in support of monolithic base fuel qualification. Mechanical properties were evaluated in four-point bending. Specimens were taken from fuel plates irradiated in the RERTR-12 and AFIP-6 Mk. II irradiation campaigns, and tests were conducted in the Hot Fuel Examination Facility (HFEF) at Idaho National Laboratory (INL). The monolithic fuel plates consist of a U-10Mo fuel meat covered with a Zr diffusion barrier layer fabricated by co-rolling, clad in 6061 Al using a hot isostatic press (HIP) bonding process. Specimens exhibited nominal (fresh)more » fuel meat thickness ranging from 0.25 mm to 0.64 mm, and fuel plate average burnup ranged from approximately 0.4 x 1021 fissions/cm 3 to 6.0 x 1021 fissions/cm 3. After sectioning the fuel plates, the 6061 Al cladding was removed by dissolution in concentrated NaOH. Pre- and post-dissolution dimensional inspections were conducted on test specimens to facilitate accurate analysis of bend test results. Four-point bend testing was conducted on the HFEF Remote Load Frame at a crosshead speed of 0.1 mm/min using custom-designed test fixtures and calibrated load cells. All specimens exhibited substantially linear elastic behavior and failed in a brittle manner. The influence of burnup on the observed slope of the stress-strain curve and the calculated fracture strength is discussed.« less

Assessment of international reference materials for isotope-ratio analysis (IUPAC Technical Report)

USGS Publications Warehouse

Brand, Willi A.; Coplen, Tyler B.; Vogl, Jochen; Rosner, Martin; Prohaska, Thomas

2014-01-01

Since the early 1950s, the number of international measurement standards for anchoring stable isotope delta scales has mushroomed from 3 to more than 30, expanding to more than 25 chemical elements. With the development of new instrumentation, along with new and improved measurement procedures for studying naturally occurring isotopic abundance variations in natural and technical samples, the number of internationally distributed, secondary isotopic reference materials with a specified delta value has blossomed in the last six decades to more than 150 materials. More than half of these isotopic reference materials were produced for isotope-delta measurements of seven elements: H, Li, B, C, N, O, and S. The number of isotopic reference materials for other, heavier elements has grown considerably over the last decade. Nevertheless, even primary international measurement standards for isotope-delta measurements are still needed for some elements, including Mg, Fe, Te, Sb, Mo, and Ge. It is recommended that authors publish the delta values of internationally distributed, secondary isotopic reference materials that were used for anchoring their measurement results to the respective primary stable isotope scale.

Determination of iridium in mafic rocks by atomic absorption

USGS Publications Warehouse

Grimaldi, F.S.; Schnepfe, M.M.

1970-01-01

Iridium is determined in mineralized mafic rocks by atomic absorption after fire-assay concentration into a gold bead. Interelement interferences in the atomic-absorption determination are removed and Ir sensitivity is increased by buffering the solutions with a mixture of copper and sodium sulphates. Substantial amounts of Ag, Al, Au, Bi, Ca, Cd, Co, Cr, Fe, Ho, Hg, K, La, Mg, Mn, Mo, Ni, Pb, Te, Ti, V, Y, Zn and platinum metals can be tolerated in the atomic-absorption determination. The sensitivity and detection limits are 3.2 and 0.25 ppm of Ir, respectively. ?? 1970.

Exothermic Surface Reactions in Alumina-Aluminum Shell-Core Nanoparticles with Iodine Oxide Decomposition Fragments

DTIC Science & Technology

2014-02-22

substantially high heat of combustion 6.22 kJ/g in comparison to other thermite reactions such as Al/CuO (4.09 kJ/g), Al/MoO3 (4.72 kJ/g), and Al/Fe2O3 (3.97 kJ...oxide shell growth on nano aluminum thermite propagation rates. Combust Flame 159:3448 3453 Granier JJ, Pantoya ML (2004) Laser ignition of...nanocomposite thermites . Combust Flame 138:373 383 2310 Page 8 of 9 J Nanopart Res (2014) 16:2310 1 3 Hlavacek V, Pranda P, Prandova K (2005) Reactivity, stored

[Qi as a materialist concept on the level of medical philosophy].

PubMed

Su, Zhan-Qing

2005-03-01

This paper has made a distinction between the materialist concept of qi on the medical philosophical level and its substantial existence, and illustrated the materiality and multiplicity of qi. Materiality refers to the objective reality, a summation of various things or phenomena related to human beings; while multiplicity refers to diversity of specific substances, each holding its individual essence. Based on two essential conceptions "xiang" and "xiangji", and combining the theories of traditional Chinese medicine and Western medicine, this paper has also made a preliminary study on the substantial existence of qi at macro- and micro-levels, and on physiological (normal) and pathological (abnormal) aspects. It is the author's argument that studies of the substantial existence of qi from different aspects, micro-dimension in particular, will push the syndrome differentiation of traditional Chinese medicine to a more subtle sphere.

Chemometric modeling of 5-Phenylthiophenecarboxylic acid derivatives as anti-rheumatic agents.

PubMed

Adhikari, Nilanjan; Jana, Dhritiman; Halder, Amit K; Mondal, Chanchal; Maiti, Milan K; Jha, Tarun

2012-09-01

Arthritis involves joint inflammation, synovial proliferation and damage of cartilage. Interleukin-1 undergoes acute and chronic inflammatory mechanisms of arthritis. Non-steroidal anti-inflammatory drugs can produce symptomatic relief but cannot act through mechanisms of arthritis. Diseases modifying anti-rheumatoid drugs reduce the symptoms of arthritis like decrease in pain and disability score, reduction of swollen joints, articular index and serum concentration of acute phage proteins. Recently, some literature references are obtained on molecular modeling of antirheumatic agents. We have tried chemometric modeling through 2D-QSAR studies on a dataset of fifty-one compounds out of which forty-four 5-Phenylthiophenecarboxylic acid derivatives have IL-1 inhibitory activity and forty-six 5-Phenylthiophenecarboxylic acid derivatives have %AIA suppressive activity. The work was done to find out the structural requirements of these anti-rheumatic agents. 2D QSAR models were generated by 2D and 3D descriptors by using multiple linear regression and partial least square method where IL-1 antagonism was considered as the biological activity parameter. Statistically significant models were developed on the training set developed by k-means cluster analysis. Sterimol parameters, electronic interaction at atom number 9, 2D autocorrelation descriptors, information content descriptor, average connectivity index chi-3, radial distribution function, Balaban 3D index and 3D-MoRSE descriptors were found to play crucial roles to modulate IL-1 inhibitory activity. 2D autocorrelation descriptors like Broto-Moreau autocorrelation of topological structure-lag 3 weighted by atomic van der Waals volumes, Geary autocorrelation-lag 7 associated with weighted atomic Sanderson electronegativities and 3D-MoRSE descriptors like 3D-MoRSE-signal 22 related to atomic van der Waals volumes, 3D-MoRSE-signal 28 related to atomic van der Waals volumes and 3D-MoRSE-signal 9 which was unweighted, were found to play important roles to model %AIA suppressive activity.

Aluminium, gallium, and molybdenum toxicity to the tropical marine microalga Isochrysis galbana.

PubMed

Trenfield, Melanie A; van Dam, Joost W; Harford, Andrew J; Parry, David; Streten, Claire; Gibb, Karen; van Dam, Rick A

2015-08-01

There is a shortage of established chronic toxicity test methods for assessing the toxicity of contaminants to tropical marine organisms. The authors tested the suitability of the tropical microalga Isochrysis galbana for use in routine ecotoxicology and assessed the effects of 72-h exposures to copper (Cu, a reference toxicant), aluminium (Al), gallium (Ga), and molybdenum (Mo), key metals of alumina refinery discharge, on the growth of I. galbana at 3 temperatures: 24 °C, 28 °C, and 31 °C. The sensitivity of both I. galbana and the test method was validated by the response to Cu exposure, with 10% and 50% effect concentrations (EC10 and EC50) of 2.5 μg/L and 18 μg/L, respectively. The EC10 and EC50 values for total Al at 28 °C were 640 μg/L and 3045 μg/L, respectively. The toxicity of both Cu and Al at 24 °C and 31 °C was similar to that at 28 °C. There was no measurable toxicity from dissolved Ga exposures of up to 6000 μg/L or exposures to dissolved Mo of up to 9500 μg/L. Solubility limits at 28 °C for the dissolved fractions (<10 kDa) of Al, Ga, and Mo were approximately 650 μg/L Al, >7000 μg/L Ga, and >6000 μg/L Mo. In test solutions containing >650 μg/L total Al, dissolved and precipitated forms of Al were present, with precipitated Al becoming more dominant as total Al increased. The test method proved suitable for routine ecotoxicology, with I. galbana showing sensitivity to Cu but Al, Ga, and Mo exhibiting little to no toxicity to this species. © 2015 SETAC.

Geochemical behavior of rare earth elements of the hydrothermal alterations within the Tepeoba porphyry Cu-Mo-Au deposits at Balikesir, NW Turkey

NASA Astrophysics Data System (ADS)

Doner, Zeynep; Abdelnasser, Amr; Kiran Yildirim, Demet; Kumral, Mustafa

2016-04-01

This work reports the geochemical characteristics and behavior of the rare earth elements (REE) of the hydrothermal alteration of the Tepeoba porphyry Cu-Mo-Au deposit located in the Anatolian tectonic belt at Biga peninsula (Locally Balikesir province), NW Turkey. The Cu-Mo-Au mineralization at this deposit hosted in the hornfels rocks and related to the silicic to intermediate intrusion of Eybek pluton. It locally formed with brecciated zones and quartz vein stockworks, as well as the brittle fracture zones associated with intense hydrothermal alteration. Three main alteration zones with gradual boundaries formed in the mine area in the hornfels rock that represents the host rock, along that contact the Eybek pluton; potassic, propylitic and phyllic alteration zones. The potassic alteration zone that formed at the center having high amount of Cu-sulfide minerals contains biotite, muscovite, and sericite with less amount of K-feldspar and associated with tourmalinization alteration. The propylitic alteration surrounds the potassic alteration having high amount of Mo and Au and contains chlorite, albite, epidote, calcite and pyrite. The phyllic alteration zone also surrounds the potassic alteration containing quartz, sericite and pyrite minerals. Based on the REE characteristics and content and when we correlate the Alteration index (AI) with the light REEs and heavy REEs of each alteration zone, it concluded that the light REEs decrease and heavy REEs increase during the alteration processes. The relationships between K2O index with Eu/Eu* and Sr/Sr* reveals a positive correlation in the potassic and phyllic alteration zones and a negative correlation in the propylitic alteration zone. This refers to the hydrothermal solution which is responsible for the studied porphyry deposits and associated potassic and phyllic alterations has a positive Eu and Sr anomaly as well as these elements were added to the altered rock from the hydrothermal solution. Keywords: Rare earth elements geochemistry; Tepeoba porphyry Cu-Mo-Au deposits; Balikesir; Turkey

Electrical transport and low-frequency noise in chemical vapor deposited single-layer MoS2 devices.

PubMed

Sharma, Deepak; Amani, Matin; Motayed, Abhishek; Shah, Pankaj B; Birdwell, A Glen; Najmaei, Sina; Ajayan, Pulickel M; Lou, Jun; Dubey, Madan; Li, Qiliang; Davydov, Albert V

2014-04-18

We have studied temperature-dependent (77-300 K) electrical characteristics and low-frequency noise (LFN) in chemical vapor deposited (CVD) single-layer molybdenum disulfide (MoS2) based back-gated field-effect transistors (FETs). Electrical characterization and LFN measurements were conducted on MoS2 FETs with Al2O3 top-surface passivation. We also studied the effect of top-surface passivation etching on the electrical characteristics of the device. Significant decrease in channel current and transconductance was observed in these devices after the Al2O3 passivation etching. For passivated devices, the two-terminal resistance variation with temperature showed a good fit to the activation energy model, whereas for the etched devices the trend indicated a hopping transport mechanism. A significant increase in the normalized drain current noise power spectral density (PSD) was observed after the etching of the top passivation layer. The observed channel current noise was explained using a standard unified model incorporating carrier number fluctuation and correlated surface mobility fluctuation mechanisms. Detailed analysis of the gate-referred noise voltage PSD indicated the presence of different trapping states in passivated devices when compared to the etched devices. Etched devices showed weak temperature dependence of the channel current noise, whereas passivated devices exhibited near-linear temperature dependence.

An Infantile Case of Transient, Severe Hypercholesterolemia with Normalization after Complete Weaning from Breast-feeding.

PubMed

Yamamoto, Yukiyo; Saito, Reiko; Goto, Motohide; Araki, Shunsuke; Kubo, Kazuyasu; Kawagoe, Rinko; Kawada, Yasusada; Kusuhara, Koichi

2012-04-01

A 20-d-old boy was referred to our department because of hyperthyrotropinemia at neonatal mass screening and diagnosed with neonatal transient hyperthyrotropinemia. A follow-up examination when the patient was 5 mo old revealed severe hypercholesterolemia. Familial hypercholesterolemia was first suspected because of the patient's significantly high levels of total and low-density lipoprotein cholesterol. The parent's serum lipid profiles were examined and found to be normal. He was completely breast-fed until 6 mo of age. Breast milk was still the main source of food for a period following weaning. At 14 mo old, the patient was weaned completely from breast milk, and his serum cholesterol levels decreased dramatically. According to the normal lipid profiles of the patient's parents and the spontaneous normalization of serum cholesterol levels after complete weaning from breast milk, breast-feeding was suggested to be responsible for his transient severe hypercholesterolemia. It is well documented that breast-fed infants have higher serum cholesterol levels than formula-fed infants. However, there is no reported case with severe hypercholesterolemia equivalent to or higher than the levels observed in the case of familial hypercholesterolemia. Although the exact mechanism is unknown, it is necessary to consider that a small number of cases develop severe hypercholesterolemia related to breast-feeding.

Gastrointestinal stromal tumors: Thirty years experience of an Institution

PubMed Central

Arolfo, Simone; Teggia, Paolo Mello; Nano, Mario

2011-01-01

AIM: To report our experience of gastrointestinal stromal tumors (GISTs) during the last 29 years. METHODS: Thirty two cases of GIST referred to our Institution from the 1st January 1981 to the 10th June 2010 were reviewed. Metastases, recurrence and survival data were collected in relation to age, history, clinical presentation, location, size, resection margins and cellular features. RESULTS: Mean age was 63.7 years (range, 40-90) and incidence was slightly higher in males (56%). R0 resection was performed in 90.7% of cases, R1 in 6.2% (2 cases) and R2 in 3.1% (one case). Using Fletcher’s classification 8/32 (25%) had high risk, 9/32 (28%) intermediate and 15/32 (47%) low risk tumors. Follow-up varied from 1 mo to 29 years, with a median of 8 years; overall survival was 75% (24/32), disease-free survival was 72% and tumor-related mortality was 9.3%. Three patients with high risk GIST were treated with imatinib mesylate: one developed a recurrence after 36 mo, and 2 are free from disease at 41 mo. CONCLUSION: Surgical treatment remains the gold standard therapy for resectable GISTs. Pathological and biological features of the neoplasm represent the most important factors predicting the prognosis. PMID:21528056

26 CFR 1.6662-4 - Substantial understatement of income tax.

Code of Federal Regulations, 2010 CFR

2010-04-01

...; General Explanations of tax legislation prepared by the Joint Committee on Taxation (the Blue Book... properly substantiated, or the taxpayer failed to keep adequate books and records with respect to the item... an understatement. (iv) Cross-reference. See § 1.6664-4(f) for certain rules regarding the...

Population-Based Pediatric Reference Intervals in General Clinical Chemistry: A Swedish Survey.

PubMed

Ridefelt, Peter

2015-01-01

Very few high quality studies on pediatric reference intervals for general clinical chemistry and hematology analytes have been performed. Three recent prospective community-based projects utilising blood samples from healthy children in Sweden, Denmark and Canada have substantially improved the situation. The Swedish survey included 701 healthy children. Reference intervals for general clinical chemistry and hematology were defined.

Reference levels of trace elements in hair samples from children and adolescents in Madrid, Spain.

PubMed

Llorente Ballesteros, María Teresa; Navarro Serrano, Irene; Izquierdo Álvarez, Silvia

2017-09-01

Hair samples are used as a tool to evaluate environmental exposure to contaminants and metabolic status in the individual. However, the use of human hair is controversial, mainly because of the lack of well-defined reference levels. In the case of Spain, very few biomonitoring studies have investigated these issues in infants, children or adolescents. To establish reference levels for trace elements in children and teenagers in Madrid, Spain. Inductively coupled plasma mass spectrometry (ICP-MS) was used to measure Al, As, Ag, Ba, Bi, Cd, Cr, Co, Cu, Fe, Mn, Mo, Ni, Pb, Se, Sr, Tl and Zn levels in hair samples from 648 healthy children and adolescents (253 boys and 395 girls) between April 2008 and December 2009. Median levels were as follows: Al 18.5μg/g, As 0.07μg/g, Ag 196ng/g, Ba 0.5μg/g, Bi 0.01μg/g, Cd 18.3ng/g, Cr 0.4μg/g, Co 14.5ng/g, Cu 25.7μg/g, Fe 15.5μg/g, Mn 328ng/g, Mo 0.04μg/g, Ni 0.5μg/g, Pb 0.70μg/g, Se 0.5μg/g, Sr 1.29μg/g, Tl 0.28ng/g and Zn 121μg/g. The values of trace elements here described could be considered as possible reference ranges for hair samples from children and adolescents aged 0-18 years living in the Madrid region (central Spain). These values could also be selected as a preliminary screening tool to assess exposure sources and to generate information needed to develop prevention strategies and likewise could be a complement to other diagnostic procedures. Copyright © 2016 Elsevier GmbH. All rights reserved.

Porcine reproductive and respiratory syndrome virus: morphological, biochemical and serological characteristics of Quebec isolates associated with acute and chronic outbreaks of porcine reproductive and respiratory syndrome.

PubMed Central

Mardassi, H; Athanassious, R; Mounir, S; Dea, S

1994-01-01

Cytolytic and noncytolytic strains of the porcine reproductive and respiratory syndrome virus (PRRSV) were isolated in primary cultures of porcine alveolar macrophages (PAM) from lung homogenates of stillborn fetuses or blood samples of dyspneic piglets collected from Quebec pig farms having experienced acute or chronic outbreaks of PRRS. Serological identification of the virus was confirmed by indirect immunofluorescence and indirect protein A-gold immunoelectron microscopy using reference antiserum prepared from experimentally-infected specific pathogen free (SPF) piglets and monoclonal antibodies (MoAbs) directed against the p15 nucleocapsid (N) protein of the reference ATCC-VR2332 isolate. Intracytoplasmic enveloped viral particles that tended to accumulate into cytoplasmic vesicles were observed in the infected PAM; no budding was demonstrated at the level of the cytoplasmic membrane. The extracellular virions appeared as pleomorphic but mostly spherical enveloped particles, 50-72 nm in diameter (averaged diameter of 50 particles was 58.3 nm), with an isometric core about 25-30 nm. Buoyant density of the virus in CsCL density gradients was estimated to 1.18-1.20 g/mL. No hemagglutinating activity was demonstrated. Analysis of semipurified virions of isolate IAF-exp91 by radioimmunoprecipitation (RIPA) and Western immunoblotting experiments, using reference rabbit and porcine hyperimmune sera, revealed four major viral proteins, a predominant 15 kD N protein and three other proteins with predicted M(r_ of 19, 26 and 42 kD. Progeny viral particles produced in PRRSV-infected PAM in the presence of tunicamycin lacked the 42 kD protein, thus confirming its N-glycosylated nature. Immunoprecipitation experiments using the anti-ATCC-VR2332 MoAbs confirmed the close antigenic relationships between Quebec and American reference isolates of PRRSV. Images Fig. 1. Fig. 2. Fig. 3. Fig. 4. Fig. 5. Fig. 6. PMID:8143254

[Dietary reference intakes of trace elements for Japanese and problems in clinical fields].

PubMed

Inoue, Yoshifumi

2016-07-01

In the dietary reference intakes, EAR(estimated average requirement), RDA(recommended dietary allowance), AL(adequate intake), DG(tentative dietary goal for preventing life style related diseases) and UL(tolerable upper intake level) of eight types of trace elements (iron: Fe, zinc: Zn, copper: Cu, manganese: Mn, iodine: I, selenium: Se, chromium: Cr, molybdenum: Mo) have been set. However, in the meals of hospitals, only iron of which has been taken into account. The content of these trace elements in the enteral nutrient released after 2000 was determined by considering the content of dietary reference intakes of trace elements for Japanese and considered so not fall into deficiency. However, enteral nutrient must be used considering the content of Zn, Cu and the Zn/Cu ratio, the selenium content, and the route of administration, in order to avoid falling into deficiency.

Using visuo-kinetic virtual reality to induce illusory spinal movement: the MoOVi Illusion

PubMed Central

Smith, Ross T.; Hunter, Estin V.; Davis, Miles G.; Sterling, Michele; Moseley, G. Lorimer

2017-01-01

Background Illusions that alter perception of the body provide novel opportunities to target brain-based contributions to problems such as persistent pain. One example of this, mirror therapy, uses vision to augment perceived movement of a painful limb to treat pain. Since mirrors can’t be used to induce augmented neck or other spinal movement, we aimed to test whether such an illusion could be achieved using virtual reality, in advance of testing its potential therapeutic benefit. We hypothesised that perceived head rotation would depend on visually suggested movement. Method In a within-subjects repeated measures experiment, 24 healthy volunteers performed neck movements to 50o of rotation, while a virtual reality system delivered corresponding visual feedback that was offset by a factor of 50%–200%—the Motor Offset Visual Illusion (MoOVi)—thus simulating more or less movement than that actually occurring. At 50o of real-world head rotation, participants pointed in the direction that they perceived they were facing. The discrepancy between actual and perceived direction was measured and compared between conditions. The impact of including multisensory (auditory and visual) feedback, the presence of a virtual body reference, and the use of 360o immersive virtual reality with and without three-dimensional properties, was also investigated. Results Perception of head movement was dependent on visual-kinaesthetic feedback (p = 0.001, partial eta squared = 0.17). That is, altered visual feedback caused a kinaesthetic drift in the direction of the visually suggested movement. The magnitude of the drift was not moderated by secondary variables such as the addition of illusory auditory feedback, the presence of a virtual body reference, or three-dimensionality of the scene. Discussion Virtual reality can be used to augment perceived movement and body position, such that one can perform a small movement, yet perceive a large one. The MoOVi technique tested here has clear potential for assessment and therapy of people with spinal pain. PMID:28243537

Using visuo-kinetic virtual reality to induce illusory spinal movement: the MoOVi Illusion.

PubMed

Harvie, Daniel S; Smith, Ross T; Hunter, Estin V; Davis, Miles G; Sterling, Michele; Moseley, G Lorimer

2017-01-01

Illusions that alter perception of the body provide novel opportunities to target brain-based contributions to problems such as persistent pain. One example of this, mirror therapy, uses vision to augment perceived movement of a painful limb to treat pain. Since mirrors can't be used to induce augmented neck or other spinal movement, we aimed to test whether such an illusion could be achieved using virtual reality, in advance of testing its potential therapeutic benefit. We hypothesised that perceived head rotation would depend on visually suggested movement. In a within-subjects repeated measures experiment, 24 healthy volunteers performed neck movements to 50 o of rotation, while a virtual reality system delivered corresponding visual feedback that was offset by a factor of 50%-200%-the Motor Offset Visual Illusion (MoOVi)-thus simulating more or less movement than that actually occurring. At 50 o of real-world head rotation, participants pointed in the direction that they perceived they were facing. The discrepancy between actual and perceived direction was measured and compared between conditions. The impact of including multisensory (auditory and visual) feedback, the presence of a virtual body reference, and the use of 360 o immersive virtual reality with and without three-dimensional properties, was also investigated. Perception of head movement was dependent on visual-kinaesthetic feedback ( p  = 0.001, partial eta squared = 0.17). That is, altered visual feedback caused a kinaesthetic drift in the direction of the visually suggested movement. The magnitude of the drift was not moderated by secondary variables such as the addition of illusory auditory feedback, the presence of a virtual body reference, or three-dimensionality of the scene. Virtual reality can be used to augment perceived movement and body position, such that one can perform a small movement, yet perceive a large one. The MoOVi technique tested here has clear potential for assessment and therapy of people with spinal pain.

High Revision Rate for Large-head Metal-on-metal THA at a Mean of 7.1 Years: A Registry Study.

PubMed

Seppänen, Matti; Laaksonen, Inari; Pulkkinen, Pekka; Eskelinen, Antti; Puhto, Ari-Pekka; Kettunen, Jukka; Leskinen, Jarkko; Manninen, Mikko; Mäkelä, Keijo

2018-06-01

Large-diameter head metal-on-metal (MoM) THA has largely been abandoned as a result of higher than anticipated revision rates. However, the majority of these implants are still in situ. Although earlier reports from the Finnish Arthroplasty Register noted similar short-term survivorship between large-diameter head MoM THA and conventional cemented THA, longer term survivorship of this population is unclear. Although reported revision rates for this implant group have been high, the majority of these implants have not been revised and followup is important to improve long-term management. The purposes of this study were (1) to compare the 10-year competing risk survivorship of large-diameter head MoM THA with the survivorship of conventional THA in the Finnish Arthroplasty Register; (2) to report the large-diameter head MoM THA survival at the manufacturer/brand level; and (3) to identify the most common reasons for revision of large-diameter head MoM THA in the Finnish Arthroplasty Register. The six most commonly used large-diameter head (≥ 38 mm) MoM THA devices in Finland between years 2004 and 2013 were selected (n = 10,959 implants). The completeness of the Finnish Registry is > 95% in primary THA and patients are censored from the date of death or at the point of emigration; followup continued until the end of 2015. The conventional THA control group consisted of the two most frequently used devices (Vision/Bimetric and ABG II/ABG II) with metal-on-polyethylene or ceramic-on-ceramic bearing surfaces implanted between 2002 and 2013 (n = 5177). The study group was formed by selecting all pairs of large-diameter head MoM and reference THA protheses within the same age group ( < 49, 50-54, 55-59, 60-64, 65-69, 70-74, and 75+ years), sex, diagnosis (osteoarthritis, other), and hospital yearly operation count (< 100 operations yearly, ≥ 100 operations yearly); 5166 matched pairs were identified. Revision for any reason was considered as the failure endpoint of followup. Implant survival (the proportion not revised) was calculated from corresponding cumulative incidence function adjusted for patient death as a competing event for revision. Large-diameter head MoM implant group revision hazard ratios with 95% confidence intervals were estimated with age group, sex, diagnosis, and hospital yearly operation count as confounding factors in a Cox regression model. Ten-year survivorship free from all-cause revision was lower for THAs that used a large-diameter femoral head than it was for the control group of conventional THA (83% [95% confidence interval {CI}, 82%-84%] versus 92% [95% CI, 91%-93%]). At the implant level, every large-diameter head MoM THA had a higher risk for revision compared with the conventional THA control group from the fourth postoperative year onward. The highest survival of MoM THA was 88% (95% CI, 86%-90%) for the ReCap/Bimetric and the lowest survival was 46% (95% CI, 41%-51%) for the recalled ASR with either the Summit® or Corail® stem. The most common revision reason in the MoM THA group was adverse reaction to metal debris, whereas dislocation was predominant in the conventional THA control group. The revision rate for all large-diameter head MoM THAs in this timeframe in the Finnish Arthroplasty Register is unacceptably high and in our view supports the decision to abandon their use. In agreement with the directives of other national organizations, we recommend regular followup of all patients with large-diameter head MoM THA. Based on our results, strict guidelines for followup should be maintained over the lifetime of the implant to assess patient symptoms and recommend revision when indicated. Level III, therapeutic study.

First-trimester fetal nasal bone length in an ethnic Chinese population.

PubMed

Sahota, D S; Leung, T Y; Chan, L W; Law, L W; Fung, T Y; Chan, O K; Lau, T K

2009-07-01

To determine reference ranges of fetal nasal bone length (NBL) in a Chinese population and to assess the value of NBL measurement in screening for chromosomal defects in the first trimester. In this prospective study the fetal profile was examined and the fetal NBL and crown-rump length (CRL) were measured in Chinese women presenting with singleton pregnancies for first-trimester screening for aneuploidy between January 2004 and June 2007. Screening was performed on the basis of nuchal translucency (NT) measurement and maternal serum free beta-human chorionic gonadotropin and pregnancy-associated plasma protein-A levels. NBL was measured in 7543 fetuses, of which 7517 were euploid. The best fit equation for median NBL in euploid fetuses in relation to CRL was: NBL (mm) = 0.4593 + (0.0186 x CRL(mm)). The NBL for gestational age (GA, in days) was given by the equation NBL(mm) = 0.2392 + (0.0027 x GA). There was no correlation between log(10)(NBL multiples of the median (MoM)) and log(10)(NT MoM) in unaffected pregnancies (r = - 0.009; P = 0.43). Only two of the 11 cases with trisomy 21 had an NBL outside the 5(th) or 95(th) centiles of the reference range for euploid fetuses. Reference ranges for NBL in a Chinese population suitable for screening for aneuploidy between 11 and 13 + 6 weeks' gestation have been derived. The NBL in Chinese fetuses is similar to that of other ethnic groups. However, unlike the determination of presence vs. absence of the nasal bone, NBL measurement is unlikely to further improve screening for aneuploidy. (c) 2009 ISUOG.

Design of Waste Heat Boiler for Scranton Army Ammunition Plant

DTIC Science & Technology

1980-08-01

order to calculate velocity measurements, the flow (stagnation pressure) was measured with a pitot tube and a slant manometer. The 1.245 m (4𔃻...p where V = velocity (ft/sec) Referring to Figure A-l and letting the subscript 1 indicate conditions at the inlet to the pitot tube where...Mexico, Mo. 65265 Frisch Dampers* Octapus Equipment Co. Buffalo, N.Y. 14221 Alternate source (s) of supply Henry Vogt Machine Co. 1000 W

Multi-component solid solution alloys having high mixing entropy

DOEpatents

Bei, Hongbin

2015-10-06

A multi-component high-entropy alloy includes a composition selected from the following group: VNbTaTiMoWRe, VNbTaTiMoW, VNbTaTiMoRe, VNbTaTiWRe, VNbTaMoWRe, VNbTiMoWRe, VTaTiMoWRe, NbTaTiMoWRe, VNbTaTiMo, VNbTaTiW, VNbTaMoW, VNbTiMoW, VTaTiMoW, NbTaTiMoW, VNbTaTiRe, VNbTaMoRe, VNbTiMoRe, VTaTiMoRe, NbTaTiMoRe, VNbTaWRe, VNbTiWRe, VTaTiWRe, NbTaTiWRe, VNbMoWRe, VTaMoWRe, NbTaMoWRe, VTiMoWRe, NbTiMoWRe, TaTiMoWRe, wherein relative amounts of each element vary by no more than .+-.15 atomic %.

Global Role and Burden of Influenza in Pediatric Respiratory Hospitalizations, 1982-2012: A Systematic Analysis.

PubMed

Lafond, Kathryn E; Nair, Harish; Rasooly, Mohammad Hafiz; Valente, Fátima; Booy, Robert; Rahman, Mahmudur; Kitsutani, Paul; Yu, Hongjie; Guzman, Guiselle; Coulibaly, Daouda; Armero, Julio; Jima, Daddi; Howie, Stephen R C; Ampofo, William; Mena, Ricardo; Chadha, Mandeep; Sampurno, Ondri Dwi; Emukule, Gideon O; Nurmatov, Zuridin; Corwin, Andrew; Heraud, Jean Michel; Noyola, Daniel E; Cojocaru, Radu; Nymadawa, Pagbajabyn; Barakat, Amal; Adedeji, Adebayo; von Horoch, Marta; Olveda, Remigio; Nyatanyi, Thierry; Venter, Marietjie; Mmbaga, Vida; Chittaganpitch, Malinee; Nguyen, Tran Hien; Theo, Andros; Whaley, Melissa; Azziz-Baumgartner, Eduardo; Bresee, Joseph; Campbell, Harry; Widdowson, Marc-Alain

2016-03-01

The global burden of pediatric severe respiratory illness is substantial, and influenza viruses contribute to this burden. Systematic surveillance and testing for influenza among hospitalized children has expanded globally over the past decade. However, only a fraction of the data has been used to estimate influenza burden. In this analysis, we use surveillance data to provide an estimate of influenza-associated hospitalizations among children worldwide. We aggregated data from a systematic review (n = 108) and surveillance platforms (n = 37) to calculate a pooled estimate of the proportion of samples collected from children hospitalized with respiratory illnesses and positive for influenza by age group (<6 mo, <1 y, <2 y, <5 y, 5-17 y, and <18 y). We applied this proportion to global estimates of acute lower respiratory infection hospitalizations among children aged <1 y and <5 y, to obtain the number and per capita rate of influenza-associated hospitalizations by geographic region and socio-economic status. Influenza was associated with 10% (95% CI 8%-11%) of respiratory hospitalizations in children <18 y worldwide, ranging from 5% (95% CI 3%-7%) among children <6 mo to 16% (95% CI 14%-20%) among children 5-17 y. On average, we estimated that influenza results in approximately 374,000 (95% CI 264,000 to 539,000) hospitalizations in children <1 y-of which 228,000 (95% CI 150,000 to 344,000) occur in children <6 mo-and 870,000 (95% CI 610,000 to 1,237,000) hospitalizations in children <5 y annually. Influenza-associated hospitalization rates were more than three times higher in developing countries than in industrialized countries (150/100,000 children/year versus 48/100,000). However, differences in hospitalization practices between settings are an important limitation in interpreting these findings. Influenza is an important contributor to respiratory hospitalizations among young children worldwide. Increasing influenza vaccination coverage among young children and pregnant women could reduce this burden and protect infants <6 mo.

Contrasting Effects of Human, Canine, and Hybrid Adenovirus Vectors on the Phenotypical and Functional Maturation of Human Dendritic Cells: Implications for Clinical Efficacy▿

PubMed Central

Perreau, Matthieu; Mennechet, Franck; Serratrice, Nicolas; Glasgow, Joel N.; Curiel, David T.; Wodrich, Harald; Kremer, Eric J.

2007-01-01

Antipathogen immune responses create a balance between immunity, tolerance, and immune evasion. However, during gene therapy most viral vectors are delivered in substantial doses and are incapable of expressing gene products that reduce the host's ability to detect transduced cells. Gene transfer efficacy is also modified by the in vivo transduction of dendritic cells (DC), which notably increases the immunogenicity of virions and vector-encoded genes. In this study, we evaluated parameters that are relevant to the use of canine adenovirus serotype 2 (CAV-2) vectors in the clinical setting by assaying their effect on human monocyte-derived DC (hMoDC). We compared CAV-2 to human adenovirus (HAd) vectors containing the wild-type virion, functional deletions in the penton base RGD motif, and the CAV-2 fiber knob. In contrast to the HAd type 5 (HAd5)-based vectors, CAV-2 poorly transduced hMoDC, provoked minimal upregulation of major histocompatibility complex class I/II and costimulatory molecules (CD40, CD80, and CD86), and induced negligible morphological changes indicative of DC maturation. Functional maturation assay results (e.g., reduced antigen uptake; tumor necrosis factor alpha, interleukin-1β [IL-1β], gamma interferon [IFN-γ], IL-10, IL-12, and IFN-α/β secretion; and stimulation of heterologous T-cell proliferation) were also significantly lower for CAV-2. Our data suggested that this was due, in part, to the use of an alternative receptor and a block in vesicular escape. Additionally, HAd5 vector-induced hMoDC maturation was independent of the aforementioned cytokines. Paradoxically, an HAd5/CAV-2 hybrid vector induced the greatest phenotypical and functional maturation of hMoDC. Our data suggest that CAV-2 and the HAd5/CAV-2 vector may be the antithesis of Adenoviridae immunogenicity and that each may have specific clinical advantages. PMID:17229706

Successful isolation and PCR amplification of DNA from National Institute of Standards and Technology herbal dietary supplement standard reference material powders and extracts.

PubMed

Cimino, Matthew T

2010-03-01

Twenty-four herbal dietary supplement powder and extract reference standards provided by the National Institute of Standards and Technology (NIST) were investigated using three different commercially available DNA extraction kits to evaluate DNA availability for downstream nucleotide-based applications. The material included samples of Camellia, Citrus, Ephedra, Ginkgo, Hypericum, Serenoa, And Vaccinium. Protocols from Qiagen, MoBio, and Phytopure were used to isolate and purify DNA from the NIST standards. The resulting DNA concentration was quantified using SYBR Green fluorometry. Each of the 24 samples yielded DNA, though the concentration of DNA from each approach was notably different. The Phytopure method consistently yielded more DNA. The average yield ratio was 22 : 3 : 1 (ng/microL; Phytopure : Qiagen : MoBio). Amplification of the internal transcribed spacer II region using PCR was ultimately successful in 22 of the 24 samples. Direct sequencing chromatograms of the amplified material suggested that most of the samples were comprised of mixtures. However, the sequencing chromatograms of 12 of the 24 samples were sufficient to confirm the identity of the target material. The successful extraction, amplification, and sequencing of DNA from these herbal dietary supplement extracts and powders supports a continued effort to explore nucleotide sequence-based tools for the authentication and identification of plants in dietary supplements. (c) Georg Thieme Verlag KG Stuttgart . New York.

Earth System Chemistry integrated Modelling (ESCiMo) with the Modular Earth Submodel System (MESSy) version 2.51

NASA Astrophysics Data System (ADS)

Jöckel, Patrick; Tost, Holger; Pozzer, Andrea; Kunze, Markus; Kirner, Oliver; Brenninkmeijer, Carl A. M.; Brinkop, Sabine; Cai, Duy S.; Dyroff, Christoph; Eckstein, Johannes; Frank, Franziska; Garny, Hella; Gottschaldt, Klaus-Dirk; Graf, Phoebe; Grewe, Volker; Kerkweg, Astrid; Kern, Bastian; Matthes, Sigrun; Mertens, Mariano; Meul, Stefanie; Neumaier, Marco; Nützel, Matthias; Oberländer-Hayn, Sophie; Ruhnke, Roland; Runde, Theresa; Sander, Rolf; Scharffe, Dieter; Zahn, Andreas

2016-03-01

Three types of reference simulations, as recommended by the Chemistry-Climate Model Initiative (CCMI), have been performed with version 2.51 of the European Centre for Medium-Range Weather Forecasts - Hamburg (ECHAM)/Modular Earth Submodel System (MESSy) Atmospheric Chemistry (EMAC) model: hindcast simulations (1950-2011), hindcast simulations with specified dynamics (1979-2013), i.e. nudged towards ERA-Interim reanalysis data, and combined hindcast and projection simulations (1950-2100). The manuscript summarizes the updates of the model system and details the different model set-ups used, including the on-line calculated diagnostics. Simulations have been performed with two different nudging set-ups, with and without interactive tropospheric aerosol, and with and without a coupled ocean model. Two different vertical resolutions have been applied. The on-line calculated sources and sinks of reactive species are quantified and a first evaluation of the simulation results from a global perspective is provided as a quality check of the data. The focus is on the intercomparison of the different model set-ups. The simulation data will become publicly available via CCMI and the Climate and Environmental Retrieval and Archive (CERA) database of the German Climate Computing Centre (DKRZ). This manuscript is intended to serve as an extensive reference for further analyses of the Earth System Chemistry integrated Modelling (ESCiMo) simulations.

Identifying and Mitigating Potential Nutrient and Sediment Hot Spots under a Future Scenario in the Missouri River Basin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, May; Zhang, Zhonglong

Using the Soil and Water Assessment Tool (SWAT) for large-scale watershed modeling could be useful for evaluating the quality of the water in regions that are dominated by nonpoint sources in order to identify potential “hot spots” for which mitigating strategies could be further developed. An analysis of water quality under future scenarios in which changes in land use would be made to accommodate increased biofuel production was developed for the Missouri River Basin (MoRB) based on a SWAT model application. The analysis covered major agricultural crops and biofuel feedstock in the MoRB, including pasture land, hay, corn, soybeans, wheat,more » and switchgrass. The analysis examined, at multiple temporal and spatial scales, how nitrate, organic nitrogen, and total nitrogen; phosphorus, organic phosphorus, inorganic phosphorus, and total phosphorus; suspended sediments; and water flow (water yield) would respond to the shifts in land use that would occur under proposed future scenarios. The analysis was conducted at three geospatial scales: (1) large tributary basin scale (two: Upper MoRB and Lower MoRB); (2) regional watershed scale (seven: Upper Missouri River, Middle Missouri River, Middle Lower Missouri River, Lower Missouri River, Yellowstone River, Platte River, and Kansas River); and (3) eight-digit hydrologic unit (HUC-8) subbasin scale (307 subbasins). Results showed that subbasin-level variations were substantial. Nitrogen loadings decreased across the entire Upper MoRB, and they increased in several subbasins in the Lower MoRB. Most nitrate reductions occurred in lateral flow. Also at the subbasin level, phosphorus in organic, sediment, and soluble forms was reduced by 35%, 45%, and 65%, respectively. Suspended sediments increased in 68% of the subbasins. The water yield decreased in 62% of the subbasins. In the Kansas River watershed, the water quality improved significantly with regard to every nitrogen and phosphorus compound. The improvement was clearly attributable to the conversion of a large amount of land to switchgrass. The Middle Lower Missouri River and Lower Missouri River were identified as hot regions. Further analysis identified four subbasins (10240002, 10230007, 10290402, and 10300200) as being the most vulnerable in terms of sediment, nitrogen, and phosphorus loadings. Overall, results suggest that increasing the amount of switchgrass acreage in the hot spots should be considered to mitigate the nutrient loads. The study provides an analytical method to support stakeholders in making informed decisions that balance biofuel production and water sustainability.« less

Response of the Martian ionosphere to solar activity including SEPs and ICMEs in a two-week period starting on 25 February 2015

NASA Astrophysics Data System (ADS)

Duru, F.; Gurnett, D. A.; Morgan, D. D.; Halekas, J.; Frahm, R. A.; Lundin, R.; Dejong, W.; Ertl, C.; Venable, A.; Wilkinson, C.; Fraenz, M.; Nemec, F.; Connerney, J. E. P.; Espley, J. R.; Larson, D.; Winningham, J. D.; Plaut, J.; Mahaffy, P. R.

2017-10-01

In a two-week period between February and March of 2015, a series of interplanetary coronal mass ejections (ICMEs) and solar energetic particle (SEP) events encountered Mars. The interactions were observed by several spacecraft, including Mars Express (MEX), Mars Atmosphere and Volatile Evolution Mission (MAVEN), and Mars Odyssey (MO). The ICME disturbances were characterized by an increase in ion speed, plasma temperature, magnetic field magnitude, and energetic electron flux. Furthermore, increased solar wind density and speeds, as well as unusually high local electron densities and high flow velocities were detected on the nightside at high altitudes during the March 8 event. These effects are thought to be due to the transport of ionospheric plasma away from Mars. In the deep nightside, the peak ionospheric electron density at the periapsis of MEX shows a substantial increase, reaching number densities about 2.7 × 104 cm-3 during the second ICME in the deep nightside. This corresponds to an increase in the MO High-Energy Neutron Detector flux suggesting an increase in the ionization of the neutral atmosphere due to the high intensity of charged particles. Measurements of the SEP fluxs show a substantial enhancement before the shock of a fourth ICME causing impact ionization and absorption of the surface echo intensity which drops to the noise levels, below 10-15 V2m-2 Hz-1 from values of about 2 × 10-14 V2m-2 Hz-1. Moreover, the peak ionospheric density exhibits a discrete enhancement over a period of about 30 h around the same location, which may be due to impact ionization. Ion escape rates at this time are estimated to be in the order of 1025 to 1026 s-1.

Graphical Technique to Support the Teaching/Learning Process of Software Process Reference Models

NASA Astrophysics Data System (ADS)

Espinosa-Curiel, Ismael Edrein; Rodríguez-Jacobo, Josefina; Fernández-Zepeda, José Alberto

In this paper, we propose a set of diagrams to visualize software process reference models (PRM). The diagrams, called dimods, are the combination of some visual and process modeling techniques such as rich pictures, mind maps, IDEF and RAD diagrams. We show the use of this technique by designing a set of dimods for the Mexican Software Industry Process Model (MoProSoft). Additionally, we perform an evaluation of the usefulness of dimods. The result of the evaluation shows that dimods may be a support tool that facilitates the understanding, memorization, and learning of software PRMs in both, software development organizations and universities. The results also show that dimods may have advantages over the traditional description methods for these types of models.

26 CFR 1.6662-5T - Substantial and gross valuation misstatements under chapter 1 (temporary).

Code of Federal Regulations, 2010 CFR

2010-04-01

..., DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES Additions to the Tax, Additional... persons). (iii) Property. For purposes of this section, the term property refers to both tangible and... adjustments. For rules relating to the penalty imposed with respect to a substantial or gross valuation...

26 CFR 1.1092(b)-5T - Definitions (temporary).

Code of Federal Regulations, 2010 CFR

2010-04-01

... defined in sections 1092(d)(4) (B) and (C) respectively. (k) Section 1256 contract. The term section 1256... referred to in paragraph (n)(1) of this section. (o) Unrecognized gain. The term unrecognized gain means unrecognized gain as defined in section 1092(a)(3)(A). (p) Substantially identical. The term substantially...

26 CFR 1.1092(b)-5T - Definitions (temporary).

Code of Federal Regulations, 2012 CFR

2012-04-01

... defined in sections 1092(d)(4) (B) and (C) respectively. (k) Section 1256 contract. The term section 1256... referred to in paragraph (n)(1) of this section. (o) Unrecognized gain. The term unrecognized gain means unrecognized gain as defined in section 1092(a)(3)(A). (p) Substantially identical. The term substantially...

26 CFR 1.1092(b)-5T - Definitions (temporary).

Code of Federal Regulations, 2014 CFR

2014-04-01

... defined in sections 1092(d)(4) (B) and (C) respectively. (k) Section 1256 contract. The term section 1256... referred to in paragraph (n)(1) of this section. (o) Unrecognized gain. The term unrecognized gain means unrecognized gain as defined in section 1092(a)(3)(A). (p) Substantially identical. The term substantially...

26 CFR 1.1092(b)-5T - Definitions (temporary).

Code of Federal Regulations, 2013 CFR

2013-04-01

... defined in sections 1092(d)(4) (B) and (C) respectively. (k) Section 1256 contract. The term section 1256... referred to in paragraph (n)(1) of this section. (o) Unrecognized gain. The term unrecognized gain means unrecognized gain as defined in section 1092(a)(3)(A). (p) Substantially identical. The term substantially...

26 CFR 1.1092(b)-5T - Definitions (temporary).

Code of Federal Regulations, 2011 CFR

2011-04-01

... defined in sections 1092(d)(4) (B) and (C) respectively. (k) Section 1256 contract. The term section 1256... referred to in paragraph (n)(1) of this section. (o) Unrecognized gain. The term unrecognized gain means unrecognized gain as defined in section 1092(a)(3)(A). (p) Substantially identical. The term substantially...

Two-axis magnetic field sensor

NASA Technical Reports Server (NTRS)

Smith, Carl H. (Inventor); Nordman, Catherine A. (Inventor); Jander, Albrecht (Inventor); Qian, Zhenghong (Inventor)

2006-01-01

A ferromagnetic thin-film based magnetic field sensor with first and second sensitive direction sensing structures each having a nonmagnetic intermediate layer with two major surfaces on opposite sides thereof having a magnetization reference layer on one and an anisotropic ferromagnetic material sensing layer on the other having a length in a selected length direction and a smaller width perpendicular thereto and parallel to the relatively fixed magnetization direction. The relatively fixed magnetization direction of said magnetization reference layer in each is oriented in substantially parallel to the substrate but substantially perpendicular to that of the other. An annealing process is used to form the desired magnetization directions.

Computer Assisted Exercise Environment for Terrorist Attack Consequence Management

DTIC Science & Technology

2006-09-01

security and crisis management. Fig. 3. Third Generation SSR for Integrated Security Sector MoD MoI MoEM MoFA Special Services Integrated Security...Ministries: MoEM , MoI, MoD, MH, MoEW, MoE, MoAF National Media, NGOs, other agencies District EOC / LEMA MHS/IDS/WIS Field EOC MHS/IDS/WIS MHS IDS...SRA EDA DG Environment ... EU SR Fund MoD MoI MoE&S MoEM ... National USA Great Britain Netherlands Germany ... Bilateral BSEC Stab. Pact ... Regional

The Dichotic Digits difference Test (DDdT): Development, Normative Data, and Test-Retest Reliability Studies Part 1.

PubMed

Cameron, Sharon; Glyde, Helen; Dillon, Harvey; Whitfield, Jessica; Seymour, John

2016-06-01

The dichotic digits test is one of the most widely used assessment tools for central auditory processing disorder. However, questions remain concerning the impact of cognitive factors on test results. To develop the Dichotic Digits difference Test (DDdT), an assessment tool that could differentiate children with cognitive deficits from children with genuine dichotic deficits based on differential test results. The DDdT consists of four subtests: dichotic free recall (FR), dichotic directed left ear (DLE), dichotic directed right ear (DRE), and diotic. Scores for six conditions are calculated (FR left ear [LE], FR right ear [RE], and FR total, as well as DLE, DRE, and diotic). Scores for four difference measures are also calculated: dichotic advantage, right-ear advantage (REA) FR, REA directed, and attention advantage. Experiment 1 involved development of the DDdT, including error rate analysis. Experiment 2 involved collection of normative and test-retest reliability data. Twenty adults (aged 25 yr 10 mo to 50 yr 7 mo, mean 36 yr 4 mo) took part in the development study; 62 normal-hearing, typically developing, primary-school children (aged 7 yr 1 mo to 11 yr 11 mo, mean 9 yr 4 mo) and 10 adults (aged 25 yr 0 mo to 51 yr 6 mo, mean 34 yr 10 mo) took part in the normative and test-retest reliability study. In Experiment 1, error rate analysis was conducted on the 36 digit-pair combinations of the DDdT. Normative data collected in Experiment 2 were arcsine transformed to achieve a distribution that was closer to a normal distribution and z-scores calculated. Pearson product-moment correlations were used to determine the strength of relationships between DDdT conditions. The development study revealed no significant differences in the adult population between test and retest on any DDdT condition. Error rates on 36 digit pairs ranged from 1.5% to 16.7%. The most and the least error-prone digits were removed before commencement of the normative data study, leaving 25 unique digit pairs. Average z-scores calculated from the arcsine-transformed data collected from the 62 children who took part in the normative data study revealed that FR dichotic processing (LE, RE, and total) was highly correlated with diotic processing (r ranging from 0.5 to 0.6; p < 0.0001). Significant improvements in performance on retest occurred for the FR LE, RE, total, and diotic conditions (p ranging from 0.05 to 0.0004), the conditions that would be expected to improve with practice if the participant's response strategies are better the second time around. The addition of a diotic control task-that shares many response demands with the usual dichotic tasks-opens up the possibility of differentiating children who perform below expectations because of poor dichotic processing skills from those who perform poorly because of impaired attention, memory, or other cognitive abilities. The high correlation between dichotic and diotic performance suggests that factors other than dichotic performance play a substantial role in a child's ability to perform a dichotic listening task. This hypothesis is investigated further in the cognitive correlation study that follows in the companion paper (DDdT Study Part 2; Cameron et al, 2016). American Academy of Audiology.

Age-related Changes in the Fracture Resistance of Male Fischer F344 Rat Bone

PubMed Central

Uppuganti, Sasidhar; Granke, Mathilde; Makowski, Alexander J.; Does, Mark D.; Nyman, Jeffry S.

2015-01-01

In addition to the loss in bone volume that occurs with age, there is a decline in material properties. To test new therapies or diagnostic tools that target such properties as material strength and toughness, a pre-clinical model of aging would be useful in which changes in bone are similar to those that occur with aging in humans. Toward that end, we hypothesized that similar to human bone, the estimated toughness and material strength of cortical bone at the apparent-level decreases with age in the male Fischer F344 rat. In addition, we tested whether the known decline in trabecular architecture in rats translated to an age-related decrease in vertebra (VB) strength and whether non-X-ray techniques could quantify tissue changes at micron and sub-micron length scales. Bones were harvested from 6-, 12-, and 24-month (mo.) old rats (n=12 per age). Despite a loss in trabecular bone with age, VB compressive strength was similar among the age groups. Similarly, whole-bone strength (peak force) in bending was maintained (femur) or increased (radius) with aging. There was though an age-related decrease in post-yield toughness (radius) and bending strength (femur). The ability to resist crack initiation was actually higher for the 12-mo. and 24-mo. than for 6-mo. rats (notch femur), but the estimated work to propagate the crack was less for the aged bone. For the femur diaphysis region, porosity increased while bound water decreased with age. For the radius diaphysis, there was an age-related increase in non-enzymatic and mature enzymatic collagen crosslinks. Both Raman spectroscopy and reference point indentation detected differences in tissue properties with age, though the trends did not necessarily match observations from human tissue. PMID:26610688

Postpartum iron status in nonlactating participants and nonparticipants in the special supplemental nutrition program for women, infants, and children.

PubMed

Pehrsson, P R; Moser-Veillon, P B; Sims, L S; Suitor, C W; Russek-Cohen, E

2001-01-01

Iron deficiency, a pervasive problem among low-income women of childbearing age, threatens maternal health and pregnancy outcomes. The Special Supplemental Nutrition Program for Women, Infants, and Children (WIC) was designed to alleviate health problems and provides supplemental nutritious foods, nutrition education, and health care referrals. The aim of this study was to examine the benefits associated with participation in WIC in terms of biochemical tests of postpartum iron status in nonlactating women. WIC participants (n = 57) and eligible nonparticipants (n = 53), matched by race and age, were followed bimonthly over 6 mo postpartum. Finger stick blood samples (500 microL) were collected for measurement of plasma ferritin, transferrin receptor (TfR), and hemoglobin (Hb). The mean (+/-SE) Hb concentration of participants exceeded that of nonparticipants from months 2 through 6. At 6 mo, the mean Hb concentration of participants was significantly higher than that of nonparticipants (8.01+/-0.12 and 7.63+/-0.12 mmol/L, respectively; P< 0.05) and the prevalence of anemia was significantly lower (17% and 51%, respectively; P<0.05). TfR and ferritin concentrations (consistently within the reference ranges) and dietary iron intakes did not differ significantly between participants and nonparticipants and were not correlated with Hb concentrations. Our results suggest that WIC participants were significantly less likely to become anemic if uninterrupted postpartum participation lasted for 6 mo. The lack of correlation among iron status indicators suggests that the lower mean Hb concentration in nonparticipants at 6 mo may not have been related to improved iron status in participants but to other nutrient deficiencies or differences in access to health care and health and nutrition education.

A combined experimental and theoretical spectroscopic protocol for determination of the structure of heterogeneous catalysts: developing the information content of the resonance Raman spectra of M1 MoVOx † †Electronic supplementary information (ESI) available. See DOI: 10.1039/c7sc01771e Click here for additional data file.

PubMed Central

Kubas, Adam; Noak, Johannes

2017-01-01

Absorption and multiwavelength resonance Raman spectroscopy are widely used to investigate the electronic structure of transition metal centers in coordination compounds and extended solid systems. In combination with computational methodologies that have predictive accuracy, they define powerful protocols to study the spectroscopic response of catalytic materials. In this work, we study the absorption and resonance Raman spectra of the M1 MoVOx catalyst. The spectra were calculated by time-dependent density functional theory (TD-DFT) in conjunction with the independent mode displaced harmonic oscillator model (IMDHO), which allows for detailed bandshape predictions. For this purpose cluster models with up to 9 Mo and V metallic centers are considered to represent the bulk structure of MoVOx. Capping hydrogens were used to achieve valence saturation at the edges of the cluster models. The construction of model structures was based on a thorough bonding analysis which involved conventional DFT and local coupled cluster (DLPNO-CCSD(T)) methods. Furthermore the relationship of cluster topology to the computed spectral features is discussed in detail. It is shown that due to the local nature of the involved electronic transitions, band assignment protocols developed for molecular systems can be applied to describe the calculated spectral features of the cluster models as well. The present study serves as a reference for future applications of combined experimental and computational protocols in the field of solid-state heterogeneous catalysis. PMID:28989667

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nandihalli, Nagaraj; Gorsse, Stéphane; Kleinke, Holger, E-mail: kleinke@uwaterloo.ca

To prepare Ni{sub 0.05}Mo{sub 3}Sb{sub 5.4}Te{sub 1.6}, the starting materials were loaded in the stoichiometric ratio into silica tubes and then heated at 1000 K. The reaction products were mixed and divided into four equal parts. The first sample was used as a reference sample called bulk. For the remaining samples, 1%, 2% and 3% by mass of MWCNT (multi-wall carbon nanotubes) were added by ball-milling. These materials were then subjected to consolidation by hot-pressing at 850 K and 56 MPa. Their transport properties were determined and compared to study the influence of MWCNT on the transport properties of Ni{submore » 0.05}Mo{sub 3}Sb{sub 5.4}Te{sub 1.6}. Scanning and transmission electron microscopy were used to study the microstructural and nanostructural features of the samples, and Raman characterization was performed to look for changes induced by ball-milling and hot-pressing of the nanotubes. Mainly due to a largely reduced thermal conductivity by 40% and a slightly reduced power factor, the figure-of-merit was improved by 25% after addition of 3 mass% of MWCNT. - Graphical abstract: Figure-of-merit of various Ni{sub 0.05}Mo{sub 3}Sb{sub 5.4}Te{sub 1.6}/CNT composites. - Highlights: • Various composites of Ni{sub 0.05}Mo{sub 3}Sb{sub 5.4}Te{sub 1.6} with carbon nanotubes were synthesized and characterized. • In each case, the thermoelectric figure-of-merit increases rapidly with increasing temperature. • With increasing amount of carbon nanotubes, the thermal conductivity decreases more than the electrical conductivity. • The composite with 3% carbon nanotubes performs better than the bulk material by 25%.« less

First-principles calculation of the structural and elastic properties of ternary metal nitrides TaxMo1-xN and TaxW1-xN

NASA Astrophysics Data System (ADS)

Bouamama, Kh.; Djemia, P.; Benhamida, M.

2015-09-01

First-principles pseudo-potentials calculations of the mixing enthalpy, of the lattice constants a0 and of the single-crystal elastic constants cij for ternary metal nitrides TaxMe1-xN (Me=Mo or W) alloys considering the cubic B1-rocksalt structure is carried out. For disordered ternary alloys, we employ the virtual crystal approximation VCA in which the alloy pseudopotentials are constructed within a first-principles VCA scheme. The supercell method SC is also used for ordered structures in order to evaluate clustering effects. We find that the mixing enthalpy still remains negative for TaxMe1-xN alloys in the whole composition range which implies these cubic TaxMo1-xN and TaxW1-xN ordered solid solutions are stable. We investigate the effect of Mo and W alloying on the trend of the mechanical properties of TaN. The effective shear elastic constant c44, the Cauchy pressure (c12-c44), and the shear to bulk modulus G/B ratio are used to discuss, respectively, the mechanical stability of the ternary structure and the brittle/ductile behavior in reference to TaN, MeN alloys. We determine the onset transition from the unstable structure to the stable one B1-rocksalt from the elastic stability criteria when alloying MeN with Ta. In a second stage, in the frame of anisotropic elasticity, we estimate by one homogenization method the averaged constants of the polycrystalline TaxMe1-xN alloys considering the special case of an isotropic medium with no crystallographic texture.

Human Actions Analysis: Templates Generation, Matching and Visualization Applied to Motion Capture of Highly-Skilled Karate Athletes

PubMed Central

Piekarczyk, Marcin; Ogiela, Marek R.

2017-01-01

The aim of this paper is to propose and evaluate the novel method of template generation, matching, comparing and visualization applied to motion capture (kinematic) analysis. To evaluate our approach, we have used motion capture recordings (MoCap) of two highly-skilled black belt karate athletes consisting of 560 recordings of various karate techniques acquired with wearable sensors. We have evaluated the quality of generated templates; we have validated the matching algorithm that calculates similarities and differences between various MoCap data; and we have examined visualizations of important differences and similarities between MoCap data. We have concluded that our algorithms works the best when we are dealing with relatively short (2–4 s) actions that might be averaged and aligned with the dynamic time warping framework. In practice, the methodology is designed to optimize the performance of some full body techniques performed in various sport disciplines, for example combat sports and martial arts. We can also use this approach to generate templates or to compare the correct performance of techniques between various top sportsmen in order to generate a knowledge base of reference MoCap videos. The motion template generated by our method can be used for action recognition purposes. We have used the DTW classifier with angle-based features to classify various karate kicks. We have performed leave-one-out action recognition for the Shorin-ryu and Oyama karate master separately. In this case, 100% actions were correctly classified. In another experiment, we used templates generated from Oyama master recordings to classify Shorin-ryu master recordings and vice versa. In this experiment, the overall recognition rate was 94.2%, which is a very good result for this type of complex action. PMID:29125560

Creating of Central Geospatial Database of the Slovak Republic and Procedures of its Revision

NASA Astrophysics Data System (ADS)

Miškolci, M.; Šafář, V.; Šrámková, R.

2016-06-01

The article describes the creation of initial three dimensional geodatabase from planning and designing through the determination of technological and manufacturing processes to practical using of Central Geospatial Database (CGD - official name in Slovak language is Centrálna Priestorová Databáza - CPD) and shortly describes procedures of its revision. CGD ensures proper collection, processing, storing, transferring and displaying of digital geospatial information. CGD is used by Ministry of Defense (MoD) for defense and crisis management tasks and by Integrated rescue system. For military personnel CGD is run on MoD intranet, and for other users outside of MoD is transmutated to ZbGIS (Primary Geodatabase of Slovak Republic) and is run on public web site. CGD is a global set of geo-spatial information. CGD is a vector computer model which completely covers entire territory of Slovakia. Seamless CGD is created by digitizing of real world using of photogrammetric stereoscopic methods and measurements of objects properties. Basic vector model of CGD (from photogrammetric processing) is then taken out to the field for inspection and additional gathering of objects properties in the whole area of mapping. Finally real-world objects are spatially modeled as a entities of three-dimensional database. CGD gives us opportunity, to get know the territory complexly in all the three spatial dimensions. Every entity in CGD has recorded the time of collection, which allows the individual to assess the timeliness of information. CGD can be utilized for the purposes of geographical analysis, geo-referencing, cartographic purposes as well as various special-purpose mapping and has the ambition to cover the needs not only the MoD, but to become a reference model for the national geographical infrastructure.

Comparison of four USEPA digestion methods for trace metal analysis using certified and Florida soils

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, M.; Ma, L.Q.

1998-11-01

It is critical to compare existing sample digestion methods for evaluating soil contamination and remediation. USEPA Methods 3050, 3051, 3051a, and 3052 were used to digest standard reference materials and representative Florida surface soils. Fifteen trace metals (Ag, As, Ba, Be, Cd, Cr, Cu, Hg, Mn, Mo, Ni, Pb, Sb, Se, and Za), and six macro elements (Al, Ca, Fe, K, Mg, and P) were analyzed. Precise analysis was achieved for all elements except for Cd, Mo, Se, and Sb in NIST SRMs 2704 and 2709 by USEPA Methods 3050 and 3051, and for all elements except for As, Mo,more » Sb, and Se in NIST SRM 2711 by USEPA Method 3052. No significant differences were observed for the three NIST SRMs between the microwave-assisted USEPA Methods 3051 and 3051A and the conventional USEPA Method 3050 Methods 3051 and 3051a and the conventional USEPA Method 3050 except for Hg, Sb, and Se. USEPA Method 3051a provided comparable values for NIST SRMs certified using USEPA Method 3050. However, for method correlation coefficients and elemental recoveries in 40 Florida surface soils, USEPA Method 3051a was an overall better alternative for Method 3050 than was Method 3051. Among the four digestion methods, the microwave-assisted USEPA Method 3052 achieved satisfactory recoveries for all elements except As and Mg using NIST SRM 2711. This total-total digestion method provided greater recoveries for 12 elements Ag, Be, Cr, Fe, K, Mn, Mo, Ni, Pb, Sb, Se, and Zn, but lower recoveries for Mg in Florida soils than did the total-recoverable digestion methods.« less

Investigations on Cs-free alternatives for negative ion formation in a low pressure hydrogen discharge at ion source relevant parameters

NASA Astrophysics Data System (ADS)

Kurutz, U.; Friedl, R.; Fantz, U.

2017-07-01

Caesium (Cs) is applied in high power negative hydrogen ion sources to reduce a converter surface’s work function and thus enabling an efficient negative ion surface formation. Inherent drawbacks with the usage of this reactive alkali metal motivate the search for Cs-free alternative materials for neutral beam injection systems in fusion research. In view of a future DEMOnstration power plant, a suitable material should provide a high negative ion formation efficiency and comply with the RAMI issues of the system: reliability, availability, maintainability, inspectability. Promising candidates, like low work function materials (molybdenum doped with lanthanum (MoLa) and LaB6), as well as different non-doped and boron-doped diamond samples were investigated in this context at identical and ion source relevant parameters at the laboratory experiment HOMER. Negative ion densities were measured above the samples by means of laser photodetachment and compared with two reference cases: pure negative ion volume formation with negative ion densities of about 1× {10}15 {{{m}}}-3 and the effect of H- surface production using an in situ caesiated stainless steel sample which yields 2.5 times higher densities. Compared to pure volume production, none of the diamond samples did exhibit a measurable increase in H- densities, while showing clear indications of plasma-induced erosion. In contrast, both MoLa and LaB6 produced systematically higher densities (MoLa: ×1.60 LaB6: ×1.43). The difference to caesiation can be attributed to the higher work functions of MoLa and LaB6 which are expected to be about 3 eV for both compared to 2.1 eV of a caesiated surface.

The effect of pH on the corrosion behavior of intermetallic compounds Ni{sub 3}(Si,Ti) and Ni{sub 3}(Si,Ti) + 2Mo in sodium chloride solutions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Priyotomo, Gadang, E-mail: gada001@lipi.go.id; Nuraini, Lutviasari, E-mail: Lutviasari@gmail.com; Kaneno, Yasuyuki, E-mail: kaneno@mtr.osakafu-u.ac.id

The corrosion behavior of the intermetallic compounds, Ni{sub 3}(Si,Ti) (L1{sub 2}: single phase) and Ni{sub 3}(Si,Ti) + 2Mo (L1{sub 2} and (L12 + Ni{sub ss}) mixture region), has been investigated using an immersion test, electrochemical method and surface analytical method (SEM; scanning electron microscope and EDAX: Energy Dispersive X-ray) in 0.5 kmol/m{sup 3} NaCl solutions at various pH. The corrosion behavior of nickel alloy C-276 was studied under the same experimental conditions as a reference. It was found that the uniform attack was observed on Ni{sub 3}(Si,Ti) for the immersion test at lower pH, while the pitting attack was observedmore » on this compound for this test at neutral solution. Furthermore, Ni{sub 3}(Si,Ti)+2Mo had the preferential dissolution of L1{sub 2} compared to (L1{sub 2} + Ni{sub ss}) mixture region at lower pH, while pitting attack occurred in (L1{sub 2} + Ni{sub ss}) mixture region at neutral solution. For both intermetallic compounds, the magnitude of pitting and uniform attack decrease with increasing pH of solutions. From the immersion test and polarization curves, the corrosion resistance of Ni{sub 3}(Si,Ti)+2Mo is lower than that of Ni{sub 3}(Si,Ti), while the nickel alloy C-276 is the highest one at various pH of solutions. On the other hand, in the lower pH of solutions, the corrosion resistance of tested materials decreased significantly compared to those in neutral and higher pH of solutions.« less

Effects of Referent Token Variability on L2 Vocabulary Learning

ERIC Educational Resources Information Center

Sommers, Mitchell S.; Barcroft, Joe

2013-01-01

Previous research has demonstrated substantially improved second language (L2) vocabulary learning when spoken word forms are varied using multiple talkers, speaking styles, or speaking rates. In contrast, the present study varied visual representations of referents for target vocabulary. English speakers learned Spanish words in formats of no…

IMPROVED TEMPERATURE STABILITY OF SULFUR DIOXIDE SAMPLES COLLECTED BY THE FEDERAL REFERENCE METHOD

EPA Science Inventory

This report describes an examination of the reagents present in the SO2 Federal Reference Method (FRM) to determine if any change in reagent concentration or condition could bring about substantial, if not complete, retardation of the effect of temperature on the stability of col...

Constitution and thermodynamics of the Mo-Ru, Mo-Pd, Ru-Pd and Mo-Ru-Pd systems

NASA Astrophysics Data System (ADS)

Kleykamp, H.

1989-09-01

The constitution of the Mo-Ru, Mo-Pd and Ru-Pd systems was reinvestigated between 800 and 2000°C. The Mo-Ru system is of the eutectic type, a σ-phase Mo 5Ru 3 exists between 1915 and 1143°C. The Mo-Pd system is characterized by an hcp phase Mo 9Pd 11 and by two peritectic reactions, β- Mo( Pd) + L = Mo9Pd11andMo9Pd11 + L = α- Pd( Mo). Mo 9Pd 11 decomposes eutectoidally at 1370°C. The Ru-Pd system is simple peritectic. The continuous series of the hcp solid solutions between Mo 9Pd 11 and ɛ-Ru(Mo, Pd) in the ternary Mo-Ru-Pd system observed at 1700°C are suppressed below 1370°C near the Mo-Pd boundary system by the formation of a narrow α + β + ɛ three-phase field. Relative partial molar Gibbs energies of Mo, Mo and Ru in the respective binary systems and of Mo in the ternary system were measured by the EMF method with a Zr(Ca)O 2 electrolyte. xsΔ ḠMo∞ quantities were evaluated at 1200 K which give -43 kJ/mol Mo in Ru and -94 kJ/mol Mo in Pd at infinite dilution. Gibbs energies of formation of the Mo-Ru and Mo-Pd systems were calculated.

Body distribution of trace elements in black-tailed gulls from Rishiri Island, Japan: age-dependent accumulation and transfer to feathers and eggs.

PubMed

Agusa, Tetsuro; Matsumoto, Taro; Ikemoto, Tokutaka; Anan, Yasumi; Kubota, Reiji; Yasunaga, Genta; Kunito, Takashi; Tanabe, Shinsuke; Ogi, Haruo; Shibata, Yasuyuki

2005-09-01

Body distribution and maternal transfer of 18 trace elements (V, Cr, Mn, Co, Cu, Zn, Se, Rb, Sr, Mo, Ag, Cd, Sb, Cs, Ba, Hg, Tl, and Pb) to eggs were examined in black-tailed gulls (Larus crassirostris), which were culled in Rishiri Island, Hokkaido Prefecture, Japan. Manganese, Cu, Rb, Mo, and Cd showed the highest levels in liver and kidney, Ag, Sb, and Hg in feather, and V, Sr, and Pb in bone. Maternal transfer rates of trace elements ranged from 0.8% (Cd) to as much as 65% (Tl) of maternal body burden. Large amounts of Sr, Ba, and Tl were transferred to the eggs, though maternal transfer rates of V, Cd, Hg, and Pb were substantially low. It also was observed that Rb, Sr, Cd, Cs, and Ba hardly were excreted into feathers. Concentrations of Co in liver, Ba in liver and kidney, and Mo in liver increased significantly with age, whereas Se in bone and kidney, Hg in kidney, and Cr in feather decreased with age in the known-aged black-tailed gulls (2-20 years old). It also was suggested that feathers might be useful to estimate contamination status of trace elements in birds, especially for Hg on a population basis, although the utility is limited on an individual basis for the black-tailed gulls. To our knowledge, this is the first report on the maternal transfer rate of multielements and also on the usefulness of feathers to estimate contamination status of Hg in birds on a population basis.

Motion vector field upsampling for improved 4D cone-beam CT motion compensation of the thorax

NASA Astrophysics Data System (ADS)

Sauppe, Sebastian; Rank, Christopher M.; Brehm, Marcus; Paysan, Pascal; Seghers, Dieter; Kachelrieß, Marc

2017-03-01

To improve the accuracy of motion vector fields (MVFs) required for respiratory motion compensated (MoCo) CT image reconstruction without increasing the computational complexity of the MVF estimation approach, we propose a MVF upsampling method that is able to reduce the motion blurring in reconstructed 4D images. While respiratory gating improves the temporal resolution, it leads to sparse view sampling artifacts. MoCo image reconstruction has the potential to remove all motion artifacts while simultaneously making use of 100% of the rawdata. However the MVF accuracy is still below the temporal resolution of the CBCT data acquisition. Increasing the number of motion bins would increase reconstruction time and amplify sparse view artifacts, but not necessarily the accuracy of MVF. Therefore we propose a new method to upsample estimated MVFs and use those for MoCo. To estimate the MVFs, a modified version of the Demons algorithm is used. Our proposed method is able to interpolate the original MVFs up to a factor that each projection has its own individual MVF. To validate the method we use an artificially deformed clinical CT scan, with a breathing pattern of a real patient, and patient data acquired with a TrueBeamTM4D CBCT system (Varian Medical Systems). We evaluate our method for different numbers of respiratory bins, each again with different upsampling factors. Employing our upsampling method, motion blurring in the reconstructed 4D images, induced by irregular breathing and the limited temporal resolution of phase-correlated images, is substantially reduced.

What are the arguments for and against rational therapy for epilepsy?

PubMed

Barker-Haliski, Melissa; Sills, Graeme J; White, H Steve

2014-01-01

Although more than a dozen new anti-seizure drugs (ASDs) have entered the market since 1993, a substantial proportion of patients (~30 %) remain refractory to current treatments. Thus, a concerted effort to identify and develop new therapies that will help these patients continues. Until this effort succeeds, it is reasonable to re-assess the use of currently available therapies and to consider how these therapies might be utilized in a more efficacious manner. This applies to the selection of monotherapies in newly-diagnosed epilepsy, but perhaps, more importantly, to the choice of combination treatments in otherwise drug-refractory epilepsy. Rational polytherapy is a concept that is predicated on the combination of drugs with complementary mechanisms of action (MoAs) that work synergistically to maximize efficacy and minimize the potential for adverse events. Furthermore, rational polytherapy requires a detailed understanding of the MoA subclasses amongst available ASDs and an appreciation of the empirical evidence that supports the use of specific combinations. The majority of ASDs can be loosely categorized into those that target neurotransmission and network hyperexcitability, modulate intrinsic neuronal properties through ion channels, or possess broad-spectrum efficacy as a result of multiple mechanisms. Within each of these categories, there are discrete pharmacological profiles that differentiate individual ASDs. This chapter will consider how knowledge of MoA can help guide therapy in a rational manner, both in the selection of monotherapies for specific seizure types and syndromes, but also in the choice of drug combinations for patients whose epilepsy is not optimally controlled with a single ASD.

Current rectification by self-assembled molecular quantum dots from first principles

NASA Astrophysics Data System (ADS)

Larade, Brian; Bratkovsky, Alexander

2003-03-01

We present results of first-principles calculations of the current rectification by self-assembled molecular quantum dots. Molecules of that kind should be synthesized with a central conjugated (narrow band-gap) part, and two peripheral saturated (wide band-gap) barrier groups of substantially different lengths L1 and L_2. The peripheral groups must end with chemical Â"anchorÂ" groups, enabling attachment of the molecule to the electrodes. In such molecules, if they are not longer than about 2-3 nm, the electron transport is likely to proceed by resonant tunneling through molecular orbitals (MO) centered on the conjugated part of the molecule (Â"quantum dotÂ") [1,2]. Generally, either LUMO (lowest unoccupied MO) or HOMO (highest occupied MO) will be most transparent to the tunneling electrons because of their different coupling to electrodes. We have studied (i) single benzene ring C6H6 [2] and (ii) naphthalene C10H8, separated from gold electrodes by alkane chains of different lengths with the use of the non-equilibrium Green's function method and self-consistent density-functional theory. The results show significant changes in electron density and potential distribution in the vicinity of molecule-electrode contact. In the case of a naphthalene quantum dot, separated from electrodes by asymmetric alkane groups (CH2)2 and (CH2)6, the I-V curve shows current rectification on the order of ˜ 10^2. [1] A.M. Bratkovsky and P.E. Kornilovitch, Phys. Rev. B (2002), to be published. [2] P. E. Kornilovitch, A.M. Bratkovsky, and R.S. Williams, Phys. Rev. B 66, 165436 (2002).

Strain Control of Exciton-Phonon Coupling in Atomically Thin Semiconductors.

PubMed

Niehues, Iris; Schmidt, Robert; Drüppel, Matthias; Marauhn, Philipp; Christiansen, Dominik; Selig, Malte; Berghäuser, Gunnar; Wigger, Daniel; Schneider, Robert; Braasch, Lisa; Koch, Rouven; Castellanos-Gomez, Andres; Kuhn, Tilmann; Knorr, Andreas; Malic, Ermin; Rohlfing, Michael; Michaelis de Vasconcellos, Steffen; Bratschitsch, Rudolf

2018-03-14

Semiconducting transition metal dichalcogenide (TMDC) monolayers have exceptional physical properties. They show bright photoluminescence due to their unique band structure and absorb more than 10% of the light at their excitonic resonances despite their atomic thickness. At room temperature, the width of the exciton transitions is governed by the exciton-phonon interaction leading to strongly asymmetric line shapes. TMDC monolayers are also extremely flexible, sustaining mechanical strain of about 10% without breaking. The excitonic properties strongly depend on strain. For example, exciton energies of TMDC monolayers significantly redshift under uniaxial tensile strain. Here, we demonstrate that the width and the asymmetric line shape of excitonic resonances in TMDC monolayers can be controlled with applied strain. We measure photoluminescence and absorption spectra of the A exciton in monolayer MoSe 2 , WSe 2 , WS 2 , and MoS 2 under uniaxial tensile strain. We find that the A exciton substantially narrows and becomes more symmetric for the selenium-based monolayer materials, while no change is observed for atomically thin WS 2 . For MoS 2 monolayers, the line width increases. These effects are due to a modified exciton-phonon coupling at increasing strain levels because of changes in the electronic band structure of the respective monolayer materials. This interpretation based on steady-state experiments is corroborated by time-resolved photoluminescence measurements. Our results demonstrate that moderate strain values on the order of only 1% are already sufficient to globally tune the exciton-phonon interaction in TMDC monolayers and hold the promise for controlling the coupling on the nanoscale.

The contribution of malabsorption to the reduction in net energy absorption after long-limb Roux-en-Y gastric bypass.

PubMed

Odstrcil, Elizabeth A; Martinez, Juan G; Santa Ana, Carol A; Xue, Beiqi; Schneider, Reva E; Steffer, Karen J; Porter, Jack L; Asplin, John; Kuhn, Joseph A; Fordtran, John S

2010-10-01

Roux-en-Y gastric bypass (RYGB) restricts food intake, and when the Roux limb is elongated to 150 cm, the procedure is believed to induce malabsorption. Our objective was to measure total reduction in intestinal absorption of combustible energy after RYGB and the extent to which this was due to restriction of food intake or malabsorption of ingested macronutrients. Long-limb RYGB was performed in 9 severely obese patients. Dietary intake and intestinal absorption of fat, protein, carbohydrate, and combustible energy were measured before and at 2 intervals after bypass. By using coefficients of absorption to measure absorptive function, equations were developed to calculate the daily gram and kilocalorie quantities of ingested macronutrients that were not absorbed because of malabsorption or restricted food intake. Coefficients of fat absorption were 92 ± 1.3% before bypass, 72 ± 5.5% 5 mo after bypass, and 68 ± 8.7% 14 mo after bypass. There were no statistically significant effects of RYGB on protein or carbohydrate absorption coefficients, although protein coefficients decreased substantially in some patients. Five months after bypass, malabsorption reduced absorption of combustible energy by 124 ± 57 kcal/d, whereas restriction of food intake reduced energy absorption by 2062 ± 271 kcal/d. Fourteen months after bypass, malabsorption reduced energy absorption by 172 ± 60 kcal/d compared with 1418 ± 171 kcal/d caused by restricted food intake. On average, malabsorption accounted for ≈6% and 11% of the total reduction in combustible energy absorption at 5 and 14 mo, respectively, after this gastric bypass procedure.

Application of advanced structure to multi-tone mask for FPD process

NASA Astrophysics Data System (ADS)

Song, Jin-Han; Jeong, Jin-Woong; Kim, Kyu-Sik; Jeong, Woo-Gun; Yun, Sang-Pil; Lee, Dong-Heok; Choi, Sang-Soo

2017-07-01

In accordance with improvement of FPD technology, masks such as phase shift mask (PSM) and multi-tone mask (MTM) for a particular purpose also have been developed. Above all, the MTM consisted of more than tri-tone transmittance has a substantial advantage which enables to reduce the number of mask demand in FPD fabrication process contrast to normal mask of two-tone transmittance.[1,2] A chromium (Cr)-based MTM (Typically top type) is being widely employed because of convenience of etch process caused by its only Cr-based structure consisted of Cr absorber layer and Cr half-tone layer. However, the top type of Cr-based MTM demands two Cr sputtering processes after each layer etching process and writing process. For this reason, a different material from the Cr-based MTM is required for reduction of mask fabrication time and cost. In this study, we evaluate a MTM which has a structure combined Cr with molybdenum silicide (MoSi) to resolve the issues mentioned above. The MoSi which is demonstrated by integrated circuit (IC) process is a suitable material for MTM evaluation. This structure could realize multi-transmittance in common with the Cr-based MTM. Moreover, it enables to reduce the number of sputtering process. We investigate a optimized structure upon consideration of productivity along with performance such as critical dimension (CD) variation and transmittance range of each structure. The transmittance is targeted at h-line wavelength (405 nm) in the evaluation. Compared with Cr-based MTM, the performances of all Cr-/MoSi-based MTMs are considered.

Stereotypic movement disorder: easily missed.

PubMed

Freeman, Roger D; Soltanifar, Atefeh; Baer, Susan

2010-08-01

To expand the understanding of stereotypic movement disorder (SMD) and its differentiation from tics and autistic stereotypies. Forty-two children (31 males, mean age 6y 3mo, SD 2y 8mo; 11 females, mean age 6y 7mo, SD 1y 9mo) consecutively diagnosed with SMD, without-self-injurious behavior, intellectual disability, sensory impairment, or an autistic spectrum disorder (ASD), were assessed in a neuropsychiatry clinic. A list of probe questions on the nature of the stereotypy was administered to parents (and to children if developmentally ready). Questionnaires administered included the Stereotypy Severity Scale, Short Sensory Profile, Strengths and Difficulties Questionnaire, Repetitive Behavior Scale--Revised, and the Developmental Coordination Disorder Questionnaire. The stereotyped movement patterns were directly observed and in some cases further documented by video recordings made by parents. The probe questions were used again on follow-up at a mean age of 10 years 7 months (SD 4y 4mo). Mean age at onset was 17 months. Males exceeded females by 3:1. Family history of a pattern of SMD was reported in 13 and neuropsychiatric comorbidity in 30 (attention-deficit-hyperactivity disorder in 16, tics in 18, and developmental coordination disorder in 16). Obsessive-compulsive disorder occurred in only two. The Short Sensory Profile correlated with comorbidity (p<0.001), the Stereotypy Severity Scale (p=0.009), and the Repetitive Behavior Scale (p<0.001); the last correlated with the Stereotypy Severity Scale (p=0.001). Children (but not their parents) liked their movements, which were usually associated with excitement or imaginative play. Mean length of follow-up was 4 years 8 months (SD 2y 10mo). Of the 39 children followed for longer than 6 months, the behavior stopped or was gradually shaped so as to occur primarily privately in 25. Misdiagnosis was common: 26 were initially referred as tics, 10 as ASD, five as compulsions, and one as epilepsy. Co-occurring facial grimacing in 15 children and vocalization in 22 contributed to diagnostic confusion. SMD occurs in children without ASD or intellectual disability. The generally favorable clinical course is largely due to a gradual increase in private expression of the movements. Severity of the stereotypy is associated with sensory differences and psychopathology. Differentiation of SMD from tics and ASD is important to avoid misdiagnosis and unnecessary treatment.

Estimating reliable paediatric reference intervals in clinical chemistry and haematology.

PubMed

Ridefelt, Peter; Hellberg, Dan; Aldrimer, Mattias; Gustafsson, Jan

2014-01-01

Very few high-quality studies on paediatric reference intervals for general clinical chemistry and haematology analytes have been performed. Three recent prospective community-based projects utilising blood samples from healthy children in Sweden, Denmark and Canada have substantially improved the situation. The present review summarises current reference interval studies for common clinical chemistry and haematology analyses. ©2013 Foundation Acta Paediatrica. Published by John Wiley & Sons Ltd.

BLAKE - A Thermodynamics Code Based on TIGER: Users’ Guide and Manual

DTIC Science & Technology

1982-07-01

hydrazine UDMH Water H20 3S I The formulas and enthalpies of formation of these ingredients are listed in Appendix B. Wherever possible they were taken...estimates for B(T), it does not improve the estimates of C(I). Numerically the contribution of the third coefficient is necessary- for loading densities ...here, C will be assumed independent of temperature. The vejume, V, is related to the reference mass, Mo, and the density , p, by P = M /V (9) 0 The

Evaluation of Gust and Draft Velocities from Flights of P-61C Airplanes within Thunderstorms August 17, 1946 to August 19, 1946 at Orlando, Florida

NASA Technical Reports Server (NTRS)

Tolefson, H. B.

1947-01-01

Results obtained from gust and draft velocity measurements within thunderstorms for the period August 17, 1946 to August 19, 1946 at Orlando, Florida are presented herein. These data are summarized in tables I and II and are of the type presented in reference 1 for previous flights. Inspection of photo-observer records taken on the present flights indicated that mo ambient-air temperature data were obtained.

An Analysis of the Psychological Necessity of Censorship in Combat Zones

DTIC Science & Technology

1970-01-01

combat actions, the Tet Offensive and Ap Bia Mo-mtain (commonly referred to as Hamburger Hill), as reported in The New York Times , San Francisco...future or to the past, to a time when thought is free, when men are different from one another and do not live alone--to a time wh’n truth exists and... manageable system of world order unless we accept the fact that occasionally violent internal and social upheavals abroad are inevitable and cannot

A Lightweight Intelligent Virtual Cinematography System for Machinima Production

DTIC Science & Technology

2007-01-01

portmanteau of machine and cinema , machinima refers to the innovation of leveraging video game technology to greatly ease the creation of computer...selecting camera angles to capture the action of an a priori unknown script as aesthetically appropriate cinema . There are a number of challenges therein...Proc. of the 4th International Conf. on Autonomous Agents. Young, R.M. and Riedl, M.O. 2003. Towards an Architecture for Intelligent Control of Narrative in Interactive Virtual Worlds. In Proc. of IUI 2003.

Micro-PIXE analysis of silicate reference standards

USGS Publications Warehouse

Czamanske, G.K.; Sisson, T.W.; Campbell, J.L.; Teesdale, W.J.

1993-01-01

The accuracy and precision of the University of Guelph proton microprobe have been evaluated through trace-element analysis of well-characterized silicate glasses and minerals, including BHVO-1 glass, Kakanui augite and hornblende, and ten other natural samples of volcanic glass, amphibole, pyroxene, and garnet. Using the 2.39 wt% Mo in a NIST steel as the standard, excellent precision and agreement between reported and analyzed abundances were obtained for Fe, Ni, Cu, Zn, Ga, Rb, Sr, Y, Zr, and Nb. -from Authors

Generation of referring expressions: assessing the Incremental Algorithm.

PubMed

van Deemter, Kees; Gatt, Albert; van der Sluis, Ielka; Power, Richard

2012-07-01

A substantial amount of recent work in natural language generation has focused on the generation of ''one-shot'' referring expressions whose only aim is to identify a target referent. Dale and Reiter's Incremental Algorithm (IA) is often thought to be the best algorithm for maximizing the similarity to referring expressions produced by people. We test this hypothesis by eliciting referring expressions from human subjects and computing the similarity between the expressions elicited and the ones generated by algorithms. It turns out that the success of the IA depends substantially on the ''preference order'' (PO) employed by the IA, particularly in complex domains. While some POs cause the IA to produce referring expressions that are very similar to expressions produced by human subjects, others cause the IA to perform worse than its main competitors; moreover, it turns out to be difficult to predict the success of a PO on the basis of existing psycholinguistic findings or frequencies in corpora. We also examine the computational complexity of the algorithms in question and argue that there are no compelling reasons for preferring the IA over some of its main competitors on these grounds. We conclude that future research on the generation of referring expressions should explore alternatives to the IA, focusing on algorithms, inspired by the Greedy Algorithm, which do not work with a fixed PO. Copyright © 2011 Cognitive Science Society, Inc.

26 CFR 7.105-1 - Questions and answers relating to exclusions of certain disability income payments.

Code of Federal Regulations, 2011 CFR

2011-04-01

... engage in any substantial gainful activity by reason of any medically determinable physical or mental... exemption for age and the credit for the elderly? A-9: No. For purposes of the disability income exclusion... substantial gainful activity referred to is not limited to the activity, or a comparable activity, in which...

Effect of exposure cycle on hot salt stress corrosion of a titanium alloy

NASA Technical Reports Server (NTRS)

Gray, H. R.; Johnston, J. R.

1974-01-01

The influence of exposure cycle on the hot-salt stress-corrosion cracking resistance of the Ti-8Al-1Mo-1V alloy was determined. Both temperature and stress were cycled simultaneously to simulate turbine-powered aircraft service cycles. Temperature and stress were also cycled independently to determine their individual effects. Substantial increases in crack threshold stresses were observed for cycles in which both temperature and stress or temperature alone were applied for 1 hour and removed for 3 hours. The crack threshold stresses for these cyclic exposures were twice those determined for continuous exposure for the same total time of 96 hours.

Atomic-absorption determination of rhodium in chromite concentrates

USGS Publications Warehouse

Schnepfe, M.M.; Grimaldi, F.S.

1969-01-01

Rhodium is determined in chromite concentrates by atomic absorption after concentration either by co-precipitation with tellurium formed by the reduction of tellurite with tin(II) chloride or by fire assay into a gold bead. Interelement interferences in the atomic-absorption determination are removed by buffering the solutions with lanthanum sulphate (lanthanum concentration 1%). Substantial amounts of Ag, Al, Au, Bi, Ca, Cd, Co, Cr, Cu, Fe, Ho, Hg, K, La, Mg, Mn, Mo, Na, Ni, Pb, Te, Ti, V, Y, Zn and platinum metals can be tolerated. A lower limit of approximately 0.07 ppm Rh can be determined in a 3-g sample. ?? 1969.

Common source cascode amplifiers for integrating IR-FPA applications

NASA Technical Reports Server (NTRS)

Woolaway, James T.; Young, Erick T.

1989-01-01

Space based astronomical infrared measurements present stringent performance requirements on the infrared detector arrays and their associated readout circuitry. To evaluate the usefulness of commercial CMOS technology for astronomical readout applications a theoretical and experimental evaluation was performed on source follower and common-source cascode integrating amplifiers. Theoretical analysis indicates that for conditions where the input amplifier integration capacitance is limited by the detectors capacitance the input referred rms noise electrons of each amplifier should be equivalent. For conditions of input gate limited capacitance the source follower should provide lower noise. Measurements of test circuits containing both source follower and common source cascode circuits showed substantially lower input referred noise for the common-source cascode input circuits. Noise measurements yielded 4.8 input referred rms noise electrons for an 8.5 minute integration. The signal and noise gain of the common-source cascode amplifier appears to offer substantial advantages in acheiving predicted noise levels.

Peroral endoscopic myotomy for treatment of Guillain-Barre syndrome-associated achalasia: A rare case

PubMed Central

Shin, Seung Kak; Kim, Kyoung Oh; Kim, Eui Joo; Kim, Su Young; Kim, Jung Ho; Kim, Yoon Jae; Chung, Jun-Won; Kwon, Kwang An; Park, Dong Kyun

2017-01-01

Guillain-Barre syndrome (GBS)-associated achalasia is a very rare disease of uncertain cause. We report the case of a patient diagnosed with GBS-associated type I achalasia who was successfully treated with peroral endoscopic myotomy (POEM). A 30-year-old man who was diagnosed with GBS 3 mo before was referred to our department with dysphagia and meal-related regurgitation. The results of esophagography, endoscopy, and high-resolution manometry (HRM) revealed type I achalasia. POEM that utilized a submucosal tunneling technique was performed to treat the GBS-associated type I achalasia. After POEM, smooth passage of a contrast agent into the stomach was shown in follow-up esophagography, and follow-up HRM revealed a decrease in the mean integrated relaxation pressure 22.9 mmHg to 9.6 mmHg. The patient remained without dysphagia for 7 mo, even though the patient’s neurological problems were not fully resolved. POEM may be a safe and effective treatment for GBS-associated type I achalasia. PMID:28223738

Alternate cathodes for sodium-metal chloride batteries

NASA Technical Reports Server (NTRS)

Ratnakumar, B. V.; Attia, A. I.; Halpert, G.

1991-01-01

Various metal chlorides were tested as possible cathode materials for sodium-metal batteries (in addition to Fe and Ni chlorides, which have been already developed to a stage of commercialization), using an electrochemical cell consisting of a pyrex tube, heated to 250 C, with the metal wire as working electrode, concentric Ni foil as counterelectrode, and high-purity Al as reference electrode. In particular, the aim of this study was to identify metal chlorides insoluble even in neutral melts, possible at the interface during overcharge, in order to eliminate the failure mode of the cell through a cationic exchange of the dissolved metal ions with sodium beta-double-prime alumina solid electrolyte. Results indicate that Mo and Co are likely alternatives to FeCl2 and NiCl2 cathodes in sodium batteries. The open circuit voltages of Na/CoCl(x) and Na/MoCl(x) cells at 250 C would be 2.55 V and 2.64 V, respectively.

Metal concentration in the tourist beaches of South Durban: An industrial hub of South Africa.

PubMed

Vetrimurugan, E; Shruti, V C; Jonathan, M P; Roy, Priyadarsi D; Kunene, N W; Villegas, Lorena Elizabeth Campos

2017-04-15

South Durban basin of South Africa has witnessed tremendous urban, industrial expansion and mass tourism impacts exerting significant pressure over marine environments. 43 sediment samples from 7 different beaches (Bluff beach; Ansteys beach; Brighton beach; Cutting beach; Isipingo beach; Tiger Rocks beach; Amanzimtoti beach) were analyzed for acid leachable metals (ALMs) Fe, Mg, Mn, Cr, Cu, Mo, Ni, Co, Pb, Cd, Zn and Hg. The metal concentrations found in all the beaches were higher than the background reference values (avg. in μgg -1 ) for Cr (223-352), Cu (27.67-42.10), Mo (3.11-4.70), Ni (93-118), Co (45.52-52.44), Zn (31.26-57.01) and Hg (1.13-2.36) suggesting the influence of industrial effluents and harbor activities in this region. Calculated geochemical indexes revealed that extreme contamination of Cr and Hg in all the beach sediments and high Cr and Ni levels poses adverse biological effects. Copyright © 2017 Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koch, D.; Fertitta, E.; Paulus, B.

Due to the importance of both static and dynamical correlation in the bond formation, low-dimensional beryllium systems constitute interesting case studies to test correlation methods. Aiming to describe the whole dissociation curve of extended Be systems we chose to apply the method of increments (MoI) in its multireference (MR) formalism. To gain insight into the main characteristics of the wave function, we started by focusing on the description of small Be chains using standard quantum chemical methods. In a next step we applied the MoI to larger beryllium systems, starting from the Be{sub 6} ring. The complete active space formalismmore » was employed and the results were used as reference for local MR calculations of the whole dissociation curve. Although this is a well-established approach for systems with limited multireference character, its application regarding the description of whole dissociation curves requires further testing. Subsequent to the discussion of the role of the basis set, the method was finally applied to larger rings and extrapolated to an infinite chain.« less

Keyphrase based Evaluation of Automatic Text Summarization

NASA Astrophysics Data System (ADS)

Elghannam, Fatma; El-Shishtawy, Tarek

2015-05-01

The development of methods to deal with the informative contents of the text units in the matching process is a major challenge in automatic summary evaluation systems that use fixed n-gram matching. The limitation causes inaccurate matching between units in a peer and reference summaries. The present study introduces a new Keyphrase based Summary Evaluator KpEval for evaluating automatic summaries. The KpEval relies on the keyphrases since they convey the most important concepts of a text. In the evaluation process, the keyphrases are used in their lemma form as the matching text unit. The system was applied to evaluate different summaries of Arabic multi-document data set presented at TAC2011. The results showed that the new evaluation technique correlates well with the known evaluation systems: Rouge1, Rouge2, RougeSU4, and AutoSummENG MeMoG. KpEval has the strongest correlation with AutoSummENG MeMoG, Pearson and spearman correlation coefficient measures are 0.8840, 0.9667 respectively.

Block correlated second order perturbation theory with a generalized valence bond reference function.

PubMed

Xu, Enhua; Li, Shuhua

2013-11-07

The block correlated second-order perturbation theory with a generalized valence bond (GVB) reference (GVB-BCPT2) is proposed. In this approach, each geminal in the GVB reference is considered as a "multi-orbital" block (a subset of spin orbitals), and each occupied or virtual spin orbital is also taken as a single block. The zeroth-order Hamiltonian is set to be the summation of the individual Hamiltonians of all blocks (with explicit two-electron operators within each geminal) so that the GVB reference function and all excited configuration functions are its eigenfunctions. The GVB-BCPT2 energy can be directly obtained without iteration, just like the second order Mo̸ller-Plesset perturbation method (MP2), both of which are size consistent. We have applied this GVB-BCPT2 method to investigate the equilibrium distances and spectroscopic constants of 7 diatomic molecules, conformational energy differences of 8 small molecules, and bond-breaking potential energy profiles in 3 systems. GVB-BCPT2 is demonstrated to have noticeably better performance than MP2 for systems with significant multi-reference character, and provide reasonably accurate results for some systems with large active spaces, which are beyond the capability of all CASSCF-based methods.

Histopathology case definition of naturally acquired Salmonella enterica serovar Dublin infection in young Holstein cattle in the northeastern United States.

PubMed

Pecoraro, Heidi L; Thompson, Belinda; Duhamel, Gerald E

2017-11-01

Salmonella enterica subsp. enterica serovar Dublin ( Salmonella Dublin) is a host-adapted bacterium that causes high morbidity and mortality in dairy cattle worldwide. A retrospective search of archives at the New York Animal Health Diagnostic Center revealed 57 culture-confirmed Salmonella Dublin cases from New York and Pennsylvania in which detailed histology of multiple tissues was available. Tissues routinely submitted by referring veterinarians for histologic evaluation included sections of heart, lungs, liver, spleen, and lymph nodes. Of the 57 S almonella Dublin-positive cases, all were Holstein breed, 53 were female (93%), and 49 (86%) were <6 mo of age. Specifically, in calves <6 mo of age, >90% (45 of 49) of lungs, 90% (28 of 31) of livers, 50% (11 of 22) of spleens, and 62% (18 of 29) of lymph nodes examined had moderate-to-severe inflammation with or without necrosis. Inconstant lesions were seen in 48% (10 of 21) of hearts examined, and consisted of variable inflammatory infiltrates and rare areas of necrosis. We propose a histopathology case definition of Salmonella Dublin in <6-mo-old Holstein cattle that includes a combination of pulmonary alveolar capillary neutrophilia with or without hepatocellular necrosis and paratyphoid granulomas, splenitis, and lymphadenitis. These findings will assist in the development of improved protocols for the diagnosis of infectious diseases of dairy cattle.

In-house cyclotron production of high-purity Tc-99m and Tc-99m radiopharmaceuticals.

PubMed

Martini, Petra; Boschi, Alessandra; Cicoria, Gianfranco; Zagni, Federico; Corazza, Andrea; Uccelli, Licia; Pasquali, Micòl; Pupillo, Gaia; Marengo, Mario; Loriggiola, Massimo; Skliarova, Hanna; Mou, Liliana; Cisternino, Sara; Carturan, Sara; Melendez-Alafort, Laura; Uzunov, Nikolay M; Bello, Michele; Alvarez, Carlos Rossi; Esposito, Juan; Duatti, Adriano

2018-05-30

In the last years, the technology for producing the important medical radionuclide technetium-99m by cyclotrons has become sufficiently mature to justify its introduction as an alternative source of the starting precursor [ 99m Tc][TcO 4 ] - ubiquitously employed for the production of 99m Tc-radiopharmaceuticals in hospitals. These technologies make use almost exclusively of the nuclear reaction 100 Mo(p,2n) 99m Tc that allows direct production of Tc-99m. In this study, it is conjectured that this alternative production route will not replace the current supply chain based on the distribution of 99 Mo/ 99m Tc generators, but could become a convenient emergency source of Tc-99m only for in-house hospitals equipped with a conventional, low-energy, medical cyclotron. On this ground, an outline of the essential steps that should be implemented for setting up a hospital radiopharmacy aimed at the occasional production of Tc-99m by a small cyclotron is discussed. These include (1) target production, (2) irradiation conditions, (3) separation/purification procedures, (4) terminal sterilization, (5) quality control, and (6) Mo-100 recovery. To address these issues, a comprehensive technology for cyclotron-production of Tc-99m, developed at the Legnaro National Laboratories of the Italian National Institute of Nuclear Physics (LNL-INFN), will be used as a reference example. Copyright © 2018 Elsevier Ltd. All rights reserved.

Initial proposition of kinematics model for selected karate actions analysis

NASA Astrophysics Data System (ADS)

Hachaj, Tomasz; Koptyra, Katarzyna; Ogiela, Marek R.

2017-03-01

The motivation for this paper is to initially propose and evaluate two new kinematics models that were developed to describe motion capture (MoCap) data of karate techniques. We decided to develop this novel proposition to create the model that is capable to handle actions description both from multimedia and professional MoCap hardware. For the evaluation purpose we have used 25-joints data with karate techniques recordings acquired with Kinect version 2. It is consisted of MoCap recordings of two professional sport (black belt) instructors and masters of Oyama Karate. We have selected following actions for initial analysis: left-handed furi-uchi punch, right leg hiza-geri kick, right leg yoko-geri kick and left-handed jodan-uke block. Basing on evaluation we made we can conclude that both proposed kinematics models seems to be convenient method for karate actions description. From two proposed variables models it seems that global might be more useful for further usage. We think that because in case of considered punches variables seems to be less correlated and they might also be easier to interpret because of single reference coordinate system. Also principal components analysis proved to be reliable way to examine the quality of kinematics models and with the plot of the variable in principal components space we can nicely present the dependences between variables.

Effects of tungsten on uptake, transport and subcellular distribution of molybdenum in oilseed rape at two different molybdenum levels.

PubMed

Qin, Shiyu; Sun, Xuecheng; Hu, Chengxiao; Tan, Qiling; Zhao, Xiaohu; Xu, Shoujun

2017-03-01

Due to the similarities of molybdenum (Mo) with tungsten (W) in the physical structure and chemical properties, studies involving the two elements have mainly examined their competitive relationships. The objectives of this study were to assess the effects of equimolar W on Mo accumulation, transport and subcellular distribution in oilseed rape at two Mo levels with four treatments: Mo 1 (1μmol/L Mo, Low Mo), Mo 1 +W 1 (1μmol/L Mo+1μmol/LW, Low Mo with Low W), Mo 200 (200μmol/L Mo, High Mo) and Mo 200 +W 200 (200μmol/L Mo+200μmol/L Mo, High Mo with high W). The fresh weight and root growth were inhibited by equimolar W at both low and high Mo levels. The Mo concentration and accumulation in root was increased by equimolar W at the low Mo level, but that in the root and shoot was decreased at the high Mo level. Additionally, equimolar W increased the Mo concentrations of xylem and phloem sap at low Mo level, but decreased that of xylem and increased that of phloem sap at the high Mo level. Furthermore, equimolar W decreased the expression of BnMOT1 in roots and leaves at the low Mo level, and only decreased its expression in leaves at the high Mo level. The expression of BnMOT2 was also decreased in root for equimolar W compared with the low Mo level, but increased compared with high Mo level. Moreover, equimolar W increased the proportion of Mo in cell wall fraction in root and that of soluble fraction in leaves when compared with the low Mo level. The results suggest that cell wall and soluble fractions might be responsible for the adaptation of oilseed rape to W stress. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Uptake of Home-Based HIV Testing, Linkage to Care, and Community Attitudes about ART in Rural KwaZulu-Natal, South Africa: Descriptive Results from the First Phase of the ANRS 12249 TasP Cluster-Randomised Trial

PubMed Central

Okesola, Nonhlanhla; Tanser, Frank; Thiebaut, Rodolphe; Rekacewicz, Claire; Newell, Marie-Louise

2016-01-01

Background The 2015 WHO recommendation of antiretroviral therapy (ART) for all immediately following HIV diagnosis is partially based on the anticipated impact on HIV incidence in the surrounding population. We investigated this approach in a cluster-randomised trial in a high HIV prevalence setting in rural KwaZulu-Natal. We present findings from the first phase of the trial and report on uptake of home-based HIV testing, linkage to care, uptake of ART, and community attitudes about ART. Methods and Findings Between 9 March 2012 and 22 May 2014, five clusters in the intervention arm (immediate ART offered to all HIV-positive adults) and five clusters in the control arm (ART offered according to national guidelines, i.e., CD4 count ≤ 350 cells/μl) contributed to the first phase of the trial. Households were visited every 6 mo. Following informed consent and administration of a study questionnaire, each resident adult (≥16 y) was asked for a finger-prick blood sample, which was used to estimate HIV prevalence, and offered a rapid HIV test using a serial HIV testing algorithm. All HIV-positive adults were referred to the trial clinic in their cluster. Those not linked to care 3 mo after identification were contacted by a linkage-to-care team. Study procedures were not blinded. In all, 12,894 adults were registered as eligible for participation (5,790 in intervention arm; 7,104 in control arm), of whom 9,927 (77.0%) were contacted at least once during household visits. HIV status was ever ascertained for a total of 8,233/9,927 (82.9%), including 2,569 ascertained as HIV-positive (942 tested HIV-positive and 1,627 reported a known HIV-positive status). Of the 1,177 HIV-positive individuals not previously in care and followed for at least 6 mo in the trial, 559 (47.5%) visited their cluster trial clinic within 6 mo. In the intervention arm, 89% (194/218) initiated ART within 3 mo of their first clinic visit. In the control arm, 42.3% (83/196) had a CD4 count ≤ 350 cells/μl at first visit, of whom 92.8% initiated ART within 3 mo. Regarding attitudes about ART, 93% (8,802/9,460) of participants agreed with the statement that they would want to start ART as soon as possible if HIV-positive. Estimated baseline HIV prevalence was 30.5% (2,028/6,656) (95% CI 25.0%, 37.0%). HIV prevalence, uptake of home-based HIV testing, linkage to care within 6 mo, and initiation of ART within 3 mo in those with CD4 count ≤ 350 cells/μl did not differ significantly between the intervention and control clusters. Selection bias related to noncontact could not be entirely excluded. Conclusions Home-based HIV testing was well received in this rural population, although men were less easily contactable at home; immediate ART was acceptable, with good viral suppression and retention. However, only about half of HIV-positive people accessed care within 6 mo of being identified, with nearly two-thirds accessing care by 12 mo. The observed delay in linkage to care would limit the individual and public health ART benefits of universal testing and treatment in this population. Trial registration ClinicalTrials.gov NCT01509508 PMID:27504637

Uptake of Home-Based HIV Testing, Linkage to Care, and Community Attitudes about ART in Rural KwaZulu-Natal, South Africa: Descriptive Results from the First Phase of the ANRS 12249 TasP Cluster-Randomised Trial.

PubMed

Iwuji, Collins C; Orne-Gliemann, Joanna; Larmarange, Joseph; Okesola, Nonhlanhla; Tanser, Frank; Thiebaut, Rodolphe; Rekacewicz, Claire; Newell, Marie-Louise; Dabis, Francois

2016-08-01

The 2015 WHO recommendation of antiretroviral therapy (ART) for all immediately following HIV diagnosis is partially based on the anticipated impact on HIV incidence in the surrounding population. We investigated this approach in a cluster-randomised trial in a high HIV prevalence setting in rural KwaZulu-Natal. We present findings from the first phase of the trial and report on uptake of home-based HIV testing, linkage to care, uptake of ART, and community attitudes about ART. Between 9 March 2012 and 22 May 2014, five clusters in the intervention arm (immediate ART offered to all HIV-positive adults) and five clusters in the control arm (ART offered according to national guidelines, i.e., CD4 count ≤ 350 cells/μl) contributed to the first phase of the trial. Households were visited every 6 mo. Following informed consent and administration of a study questionnaire, each resident adult (≥16 y) was asked for a finger-prick blood sample, which was used to estimate HIV prevalence, and offered a rapid HIV test using a serial HIV testing algorithm. All HIV-positive adults were referred to the trial clinic in their cluster. Those not linked to care 3 mo after identification were contacted by a linkage-to-care team. Study procedures were not blinded. In all, 12,894 adults were registered as eligible for participation (5,790 in intervention arm; 7,104 in control arm), of whom 9,927 (77.0%) were contacted at least once during household visits. HIV status was ever ascertained for a total of 8,233/9,927 (82.9%), including 2,569 ascertained as HIV-positive (942 tested HIV-positive and 1,627 reported a known HIV-positive status). Of the 1,177 HIV-positive individuals not previously in care and followed for at least 6 mo in the trial, 559 (47.5%) visited their cluster trial clinic within 6 mo. In the intervention arm, 89% (194/218) initiated ART within 3 mo of their first clinic visit. In the control arm, 42.3% (83/196) had a CD4 count ≤ 350 cells/μl at first visit, of whom 92.8% initiated ART within 3 mo. Regarding attitudes about ART, 93% (8,802/9,460) of participants agreed with the statement that they would want to start ART as soon as possible if HIV-positive. Estimated baseline HIV prevalence was 30.5% (2,028/6,656) (95% CI 25.0%, 37.0%). HIV prevalence, uptake of home-based HIV testing, linkage to care within 6 mo, and initiation of ART within 3 mo in those with CD4 count ≤ 350 cells/μl did not differ significantly between the intervention and control clusters. Selection bias related to noncontact could not be entirely excluded. Home-based HIV testing was well received in this rural population, although men were less easily contactable at home; immediate ART was acceptable, with good viral suppression and retention. However, only about half of HIV-positive people accessed care within 6 mo of being identified, with nearly two-thirds accessing care by 12 mo. The observed delay in linkage to care would limit the individual and public health ART benefits of universal testing and treatment in this population. ClinicalTrials.gov NCT01509508.

Homogeneity study of a corn flour laboratory reference material candidate for inorganic analysis.

PubMed

Dos Santos, Ana Maria Pinto; Dos Santos, Liz Oliveira; Brandao, Geovani Cardoso; Leao, Danilo Junqueira; Bernedo, Alfredo Victor Bellido; Lopes, Ricardo Tadeu; Lemos, Valfredo Azevedo

2015-07-01

In this work, a homogeneity study of a corn flour reference material candidate for inorganic analysis is presented. Seven kilograms of corn flour were used to prepare the material, which was distributed among 100 bottles. The elements Ca, K, Mg, P, Zn, Cu, Fe, Mn and Mo were quantified by inductively coupled plasma optical emission spectrometry (ICP OES) after acid digestion procedure. The method accuracy was confirmed by analyzing the rice flour certified reference material, NIST 1568a. All results were evaluated by analysis of variance (ANOVA) and principal component analysis (PCA). In the study, a sample mass of 400mg was established as the minimum mass required for analysis, according to the PCA. The between-bottle test was performed by analyzing 9 bottles of the material. Subsamples of a single bottle were analyzed for the within-bottle test. No significant differences were observed for the results obtained through the application of both statistical methods. This fact demonstrates that the material is homogeneous for use as a laboratory reference material. Copyright © 2015 Elsevier Ltd. All rights reserved.

Performance of repair welds on aged Cr-Mo piping girth welds

NASA Astrophysics Data System (ADS)

Viswanathan, R.; Gandy, D. W.

1999-10-01

This article documents the results of an industry survey of weld repair practices and describes the results of experimental evaluations performed on service-aged 21/4 Cr-1Mo steel piping using SMAW with both conventional postweld heat treatments and temper bead repair techniques. The overall results of this program provide substantial evidence that service-aged piping systems can be successfully weld repaired with and without postweld heat treatments and that life extension by several decades is achievable under the right design and repair conditions. Weld repairs performed on degraded exservice welds resulted in restoration or improvement of tensile and creep properties. Microhardness test results within the heat-affected zone of each weldment indicated that the temper bead weld repairs produced only slightly higher peak hardness values than those measured for the fully postweld heat treated repairs. Finally, in terms of toughness, temper bead weld repairs consistently produced higher impact properties than those measured for the postweld heat treated weldments. Gas tungsten arc weld repairs with postweld heat treatment resulted in the best combination of tensile strength, uniform microhardness distribution across the weld, Charpy toughness, and creep rupture life.

Equation of state of U2Mo up-to Mbar pressure range: Ab-initio study

NASA Astrophysics Data System (ADS)

Mukherjee, D.; Sahoo, B. D.; Joshi, K. D.; Kaushik, T. C.

2018-04-01

Experimentally, U2Mo is known to exist in tetragonal structure at ambient conditions. In contrast to experimental reports, the past theoretical studies carried out in this material do not find this phase to be stable structure at zero pressure. In order to examine this discrepancy between experiment and theory, we have performed ab-initio electronic band structure calculations on this material. In our theoretical study, we have attempted to search for lowest enthalpy structure at ambient as well at high pressure up to 200 GPa, employing evolutionary structure search algorithm in conjunction with ab-inito method. Our investigations suggest that a hexagonal structure with space group symmetry P6/mmm is the lowest enthalpy structure not only at ambient pressure but also up to pressure range of ˜200 GPa. To further, substantiate the results of these static lattice calculations the elastic and lattice dynamical stability has also been analysed. The theoretical isotherm derived from these calculations has been utilized to determine the Hugoniot of this material. Various physical properties such as zero pressure equilibrium volume, bulk modulus and its pressure derivative has also been derived from theoretical isotherm.

Method for fabricating {sup 99}Mo production targets using low enriched uranium, {sup 99}Mo production targets comprising low enriched uranium

DOEpatents

Wiencek, T.C.; Matos, J.E.; Hofman, G.L.

1997-03-25

A radioisotope production target and a method for fabricating a radioisotope production target is provided, wherein the target comprises an inner cylinder, a foil of fissionable material circumferentially contacting the outer surface of the inner cylinder, and an outer hollow cylinder adapted to receive the substantially foil-covered inner cylinder and compress tightly against the foil to provide good mechanical contact therewith. The method for fabricating a primary target for the production of fission products comprises preparing a first substrate to receive a foil of fissionable material so as to allow for later removal of the foil from the first substrate, preparing a second substrate to receive the foil so as to allow for later removal of the foil from the second substrate; attaching the first substrate to the second substrate such that the foil is sandwiched between the first substrate and second substrate to prevent foil exposure to ambient atmosphere, and compressing the exposed surfaces of the first and second substrate to assure snug mechanical contact between the foil, the first substrate and the second substrate. 3 figs.

Effects of wildfire on sea otter (Enhydra lutris) gene transcript profiles

USGS Publications Warehouse

Bowen, Lizabeth; Miles, A. Keith; Kolden, Crystal A.; Saarinen, Justin A.; Bodkin, James L.; Murray, Michael J.; Tinker, M. Tim

2015-01-01

Wildfires have been shown to impact terrestrial species over a range of temporal scales. Little is known, however, about the more subtle toxicological effects of wildfires, particularly in downstream marine or downwind locations from the wildfire perimeter. These down-current effects may be just as substantial as those effects within the perimeter. We used gene transcription technology, a sensitive indicator of immunological perturbation, to study the effects of the 2008 Basin Complex Fire on the California coast on a sentinel marine species, the sea otter (Enhydra lutris). We captured sea otters in 2008 (3 mo after the Basin Complex Fire was controlled) and 2009 (15 mo after the Basin Complex Fire was controlled) in the adjacent nearshore environment near Big Sur, California. Gene responses were distinctly different between Big Sur temporal groups, signifying detoxification of PAHs, possible associated response to potential malignant transformation, and suppression of immune function as the primary responses of sea otters to fire in 2008 compared to those captured in 2009. In general, gene transcription patterns in the 2008 sea otters were indicative of molecular reactions to organic exposure, malignant transformation, and decreased ability to respond to pathogens that seemed to consistent with short-term hydrocarbon exposure.

Development and characterization of sub-monolayer coatings as novel calibration samples for X-ray spectroscopy

NASA Astrophysics Data System (ADS)

Hönicke, Philipp; Krämer, Markus; Lühl, Lars; Andrianov, Konstantin; Beckhoff, Burkhard; Dietsch, Rainer; Holz, Thomas; Kanngießer, Birgit; Weißbach, Danny; Wilhein, Thomas

2018-07-01

With the advent of both modern X-ray fluorescence (XRF) methods and improved analytical reliability requirements the demand for suitable reference samples has increased. Especially in nanotechnology with the very low areal mass depositions, quantification becomes considerably more difficult. However, the availability of suited reference samples is drastically lower than the demand. Physical vapor deposition techniques have been enhanced significantly in the last decade driven by the need for extremely precise film parameters in multilayer production. We have applied those techniques for the development of layer-like reference samples with mass depositions in the ng-range and well below for Ca, Cu, Pb, Mo, Pd, Pb, La, Fe and Ni. Numerous other elements would also be possible. Several types of reference samples were fabricated: multi-elemental layer and extremely low (sub-monolayer) samples for various applications in XRF and total-reflection XRF analysis. Those samples were characterized and compared at three different synchrotron radiation beamlines at the BESSY II electron storage ring employing the reference-free XRF approach based on physically calibrated instrumentation. In addition, the homogeneity of the multi-elemental coatings was checked at the P04 beamline at DESY. The measurements demonstrate the high precision achieved in the manufacturing process as well as the versatility of application fields for the presented reference samples.

Eight RGS and RGS-like Proteins Orchestrate Growth, Differentiation, and Pathogenicity of Magnaporthe oryzae

PubMed Central

Zhang, Haifeng; Tang, Wei; Liu, Kaiyue; Huang, Qian; Zhang, Xin; Yan, Xia; Chen, Yue; Wang, Jiansheng; Qi, Zhongqiang; Wang, Zhengyi; Zheng, Xiaobo; Wang, Ping; Zhang, Zhengguang

2011-01-01

A previous study identified MoRgs1 as an RGS protein that negative regulates G-protein signaling to control developmental processes such as conidiation and appressorium formation in Magnaporthe oryzae. Here, we characterized additional seven RGS and RGS-like proteins (MoRgs2 through MoRgs8). We found that MoRgs1 and MoRgs4 positively regulate surface hydrophobicity, conidiation, and mating. Indifference to MoRgs1, MoRgs4 has a role in regulating laccase and peroxidase activities. MoRgs1, MoRgs2, MoRgs3, MoRgs4, MoRgs6, and MoRgs7 are important for germ tube growth and appressorium formation. Interestingly, MoRgs7 and MoRgs8 exhibit a unique domain structure in which the RGS domain is linked to a seven-transmembrane motif, a hallmark of G-protein coupled receptors (GPCRs). We have also shown that MoRgs1 regulates mating through negative regulation of Gα MoMagB and is involved in the maintenance of cell wall integrity. While all proteins appear to be involved in the control of intracellular cAMP levels, only MoRgs1, MoRgs3, MoRgs4, and MoRgs7 are required for full virulence. Taking together, in addition to MoRgs1 functions as a prominent RGS protein in M. oryzae, MoRgs4 and other RGS and RGS-like proteins are also involved in a complex process governing asexual/sexual development, appressorium formation, and pathogenicity. PMID:22241981

Charge disproportionation in tetragonal La2MoO5, a small band gap semiconductor influenced by direct Mo-Mo bonding.

PubMed

Colabello, Diane M; Camino, Fernando E; Huq, Ashfia; Hybertsen, Mark; Khalifah, Peter G

2015-01-28

The structure of the novel compound La2MoO5 has been solved from powder X-ray and neutron diffraction data and belongs to the tetragonal space group P4/m (no. 83) with a = 12.6847(3) Å and c = 6.0568(2) Å and with Z = 8. It consists of equal proportions of bioctahedral (Mo2O10) and square prismatic (Mo2O8) dimers, both of which contain direct Mo-Mo bonds and are arranged in 1D chains. The Mo-Mo bond length in the Mo2O10 dimers is 2.684(8) Å, while there are two types of Mo2O8 dimers with Mo-Mo bonds lengths of 2.22(2) and 2.28(2) Å. Although the average Mo oxidation state in La2MoO5 is 4+, the very different Mo-Mo distances reflect the fact that the Mo2O10 dimers contain only Mo(5+) (d(1)), while the prismatic Mo2O8 dimers only contain Mo(3+) (d(3)), a result directly confirmed by density function theory calculations. This is due to the complete disproportionation of Mo(4+), a phenomenon which has not previously been observed in solid-state compounds. La2MoO5 is diamagnetic, behavior which is not expected for a nonmetallic transition-metal oxide whose cation sites have an odd number of d-electrons. The resistivity displays the Arrhenius-type activated behavior expected for a semiconductor with a band gap of 0.5 eV, exhibiting an unusually small transport gap relative to other diamagnetic oxides. Diffuse reflectance studies indicate that La2MoO5 is a rare example of a stable oxide semiconductor with strong infrared absorbance. It is shown that the d-orbital splitting associated with the Mo2O8 and Mo2O10 dimeric units can be rationalized using simple molecular orbital bonding concepts.

Annotated Selected Bibliography & Index for Teaching African-American Learners: Culturally Responsive Pedagogy Project.

ERIC Educational Resources Information Center

Hilliard, Asa G.

This annotated bibliography and index presents nearly 2,000 references that are substantially unique to African or African American teaching and learning. Designed to support teacher education, the bibliography features references that were chosen if they were culturally relevant, recognized the African or African American experience, and drew…

Effects of Mo Content on Microstructure and Mechanical Property of PH13-8Mo Martensitic Precipitation-Hardened Stainless Steel

NASA Astrophysics Data System (ADS)

Yubing, Pei; Tianjian, Wang; Zhenhuan, Gao; Hua, Fan; Gongxian, Yang

This paper introduces the effects of Mo content on microstructure and mechanical property of PH13-8Mo martensitic precipitation-hardened stainless steel which is used for LP last stage blade in steam turbine. Thermodynamic software Thermo-Calc has been used to calculate precipitation temperature and the mass fraction of precipitated phases in PH13-8Mo steel with different Mo content. The result shows that when the mass of Mo is below 0.6wt.%, chi-phase mu-phase and sigma-phase could disappear. The microstructure and mechanical property of high Mo PH13-8Mo (Mo=0.57wt.%) and low Mo PH13-8Mo (Mo=2.15wt.%)have been investigated in different heat treatments. The investigations reveal that austenitizing temperature decrease with the reduce of Mo content, so the optimum solution temperature for low Mo PH13-8Mo is lower than that for high Mo PH13-8Mo.The influence of solution temperature on grain size is weakened with the increase of Mo content, Mo rich carbides could retard coarsening of grain. An enormous amount of nano-size uniformly distributed β-NiAl particles are found in both kinds of steels using transmission electron microscopy, they are the most important strengthening phase in PH13-8Mo.

The Role of Oxygen in the Evolution of Molybdenum Nitrogenase

NASA Astrophysics Data System (ADS)

Peters, J.; Boyd, E. S.; Hamilton, T. L.

2012-12-01

Since early in Earth's history, the supply of nitrogen (N) into the biosphere has been controlled by the activity of nitrogenase, an oxygen sensitive enzyme that catalyzes the reduction of dinitrogen gas (N2) to bioavailable ammonia. The most common form of nitrogenase harbors a complex molybdenum (Mo) cofactor at its active site [Mo-nitrogenase (Nif)], although other phylogenetically related (alternative) forms of nitrogenase that differ in their active-site metal composition also likely contribute NH3 in environments that are limiting in Mo. The solubility of Mo is significantly influenced by redox and this fact has been used to argue that that the iron (Fe)-dependent nitrogenase (Anf) was predominant prior to ~ 2.5 Ga because oceans were depleted in Mo and rich in Fe. This hypothesis, however, is inconsistent with recent phylogenetic data which strongly suggest that Anf is derived from Nif. Here, we examine the evolutionary history of the Nif enzyme complex in reference to the physiological, biochemical, and morphological strategies for reducing damage by molecular oxygen. A total of 189 nif operons were characterized and quantitatively mapped on a NifHDK concatenated phylogenetic tree. An overlay of the primary mode of metabolism, as defined as either anaerobic (AN) or aerobic/facultative aerobic (AFA), on the NifHDK tree indicates that Nif originated in an anoxic environment and was first acquired in an AFA lineage within the actinobacteria. The complexity of nif operons increased during the evolutionary history of Nif, with a pronounced increase observed during the transition from AN to AFA modes of metabolism. This increase in operon complexity is accompanied by a number of gene loss (nifI1 and nifI2) and gene acquisition (nifW, nifT, nifZ, nifQ) events, with variation in the overall composition of nif operons attributable to adaptations that mediated the toxicity of O2. Collectively, these results underscore the role of O2 in shaping the evolutionary history of Nif, presumably through selection to evolve regulatory and/or protective mechanisms to temporally or spatially decouple N2 fixation from aerobic metabolism.

Neurodevelopment, nutrition, and growth until 12 mo of age in infants fed a low-energy, low-protein formula supplemented with bovine milk fat globule membranes: a randomized controlled trial.

PubMed

Timby, Niklas; Domellöf, Erik; Hernell, Olle; Lönnerdal, Bo; Domellöf, Magnus

2014-04-01

Observational studies have indicated that differences in the composition of human milk and infant formula yield benefits in cognitive development and early growth for breastfed infants. The objective was to test the hypothesis that feeding an infant formula with reduced energy and protein densities and supplemented with bovine milk fat globule membrane (MFGM) reduces differences in cognitive development and early growth between formula-fed and breastfed infants. In a prospective, double-blind, randomized controlled trial, 160 infants <2 mo of age were randomly assigned to be fed an MFGM-supplemented, low-energy, low-protein experimental formula (EF) or a standard formula (SF) until 6 mo of age. The energy and protein contents of the EF and SF were 60 and 66 kcal/100 mL and 1.20 and 1.27 g/100 mL, respectively. A breastfed reference (BFR) group consisted of 80 infants. At 12 mo of age, the cognitive score (mean ± SD) on testing with the Bayley Scales of Infant and Toddler Development, Third Edition, was significantly higher in the EF group than in the SF group (105.8 ± 9.2 compared with 101.8 ± 8.0; P = 0.008) but was not significantly different from that in the BFR group (106.4 ± 9.5; P = 0.73). The EF group ingested larger volumes of formula than did the SF group (864 ± 174 compared with 797 ± 165 mL/d; P = 0.022), fully compensating for the lower energy density. No significant differences in linear growth, weight gain, body mass index, percentage body fat, or head circumference were found between the EF and SF groups. MFGM supplementation to infant formula narrows the gap in cognitive development between breastfed and formula-fed infants. Between 2 and 6 mo of age, formula-fed term infants have the capacity to upregulate their ingested volumes when the energy density of formula is reduced from 66 to 60 kcal/100 mL.

Concentrations of metals in blood and feathers of nestling ospreys (Pandion haliaetus) in Chesapeake and Delaware Bays

USGS Publications Warehouse

Rattner, B.A.; Golden, N.H.; Toschik, P.C.; McGowan, P.C.; Custer, T.W.

2008-01-01

In 2000, 2001, and 2002, blood and feather samples were collected from 40-45-day-old nestling ospreys (Pandion haliaetus) from Chesapeake Bay and Delaware Bay and River. Concentrations of 18 metals, metalloids, and other elements were determined in these samples by inductively coupled plasma-mass spectroscopy, and Hg concentrations were measured by cold vapor atomic absorption spectroscopy. When compared to concurrent reference areas (South, West, and Rhode Rivers), mean As and Hg concentrations in blood were greater (p < 0.05) in two of three Chesapeake Bay regions of concern (Baltimore Harbor [As: 1.18 vs. 0.548 mug/g dw], Anacostia River [Hg: 0.305 vs. 0.178 mug/g dw], and Elizabeth River [As: 0.876 vs. 0.663 mug/g dw; Hg: 0.260 vs. 0.180 mug/g dw]). Lead was detected more frequently in blood of nestlings from the highly industrialized Elizabeth River compared to the rural reference area. When compared to the concurrent reference area, mean Al, Ba, Hg, Mn, and Pb concentrations in feathers were substantially greater (p < 0.05) in one or more Chesapeake regions of concern (Anacostia River [Al: 206 vs. 62.1 mug/g dw; Ba: 3.31 vs. 0.823 mug/g dw; Mn: 65.4 vs. 22.9 mug/g dw] and Elizabeth River [Al: 165 vs. 63.5 mug/g dw; Hg: 1.24 vs. 0.599 mug/g dw; Pb 1.47 vs. 0.543 mug/g dw]). When compared to the coastal Inland Bays reference area, feathers of nestlings from northern Delaware Bay and River had greater concentrations (p < 0.05) of Ba (1.90 vs. 0.660 mug/g dw), Fe (258 vs. 109 mug/g dw), Mn (18.5 vs. 4.66 mug/g dw), Mo (0.130 vs. 0.040 mug/g dw), Pb (1.96 vs. 0.624 mug/g dw), and V (0.671 vs. 0.325 mug/g dw), presumably due to extensive metal-working and petroleum refinery activities. Concentrations of Hg in nestling feathers from Delaware were frequently greater than in the Chesapeake. The present findings and those of related reproductive studies suggest that concentrations of several heavy metals (e.g., Cd, Hg, Pb) in nestling blood and feathers from Chesapeake and Delaware Bays were below toxicity thresholds and do not seem to be affecting chick survival during the nestling period.

Interprofessional, multiple step simulation course improves pediatric resident and nursing staff management of pediatric patients with diabetic ketoacidosis

PubMed Central

Larson-Williams, Linnea M; Youngblood, Amber Q; Peterson, Dawn Taylor; Zinkan, J Lynn; White, Marjorie L; Abdul-Latif, Hussein; Matalka, Leen; Epps, Stephen N; Tofil, Nancy M

2016-01-01

AIM To investigate the use of a multidisciplinary, longitudinal simulation to educate pediatric residents and nurses on management of pediatric diabetic ketoacidosis. METHODS A multidisciplinary, multiple step simulation course was developed by faculty and staff using a modified Delphi method from the Pediatric Simulation Center and pediatric endocrinology department. Effectiveness of the simulation for the residents was measured with a pre- and post-test and a reference group not exposed to simulation. A follow up post-test was completed 3-6 mo after the simulation. Nurses completed a survey regarding the education activity. RESULTS Pediatric and medicine-pediatric residents (n = 20) and pediatric nurses (n = 25) completed the simulation course. Graduating residents (n = 16) were used as reference group. Pretest results were similar in the control and intervention group (74% ± 10% vs 76% ± 15%, P = 0.658). After completing the intervention, participants improved in the immediate post-test in comparison to themselves and the control group (84% ± 12% post study; P < 0.05). The 3-6 mo follow up post-test results demonstrated knowledge decay when compared to their immediate post-test results (78% ± 14%, P = 0.761). Residents and nurses felt the interdisciplinary and longitudinal nature of the simulation helped with learning. CONCLUSION Results suggest a multidisciplinary, longitudinal simulation improves immediate post-intervention knowledge but important knowledge decay occurs, future studies are needed to determine ways to decrease this decay. PMID:27896145

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baljinnyam, N.; Frontasyeva, M. V.; Ostrovnaya, T. M.

Asian medicinal herbs Chrysanthemum (Spiraea aquilegifolia Pall.) and Red Sandalwood (Pterocarpus Santalinus) are widely used in folk and Ayurvedic medicine for healing and preventing some diseases. The modern medical science has proved that the Chrysanthemum (Spiraea aquilegifolia Pall.) possesses the following functions: reducing blood press, dispelling cancer cell, coronary artery's expanding and bacteriostating and Red Sandalwood (Pterocarpus Santalinus) is recommended against headache, toothache, skin diseases, vomiting and sometimes it is taken for treatment of diabetes. Species of Chrysanthemums were collected in the north-eastern and central Mongolia, and the Red Sandalwood powder was imported from India. Samples of Chrysanthemums (branches, flowersmore » and leaves)(0.5 g) and red sandalwood powder (0.5 g) were subjected to the multi-element instrumental neutron activation analysis using epithermal neutrons (ENAA) at the IBR-2 reactor, Frank Laboratory of Neutron Physics (FLNP) JINR, Dubna. A total of 41 elements (Na, Mg, Al, Cl, K, Ca, Sc, V, Cr, Mn, Fe, Co, Ni, Zn, As, Se, Br, Rb, Sr, Zr, Mo, Cd, Cs, Ba, La, Hf, Ta, W, Sb, Au, Hg, Ce, Nd, Sm, Eu, Tb, Dy, Yb, Th, U, Lu) were determined. For the first time such a large group of elements was determined in the herbal plants used in Mongolia. The quality control of the analytical results was provided by using certified reference material Bowen Cabbage. The results obtained are compared to the ''Reference plant? data (B. Markert, 1992) and interpreted in terms of excess of such elements as Se, Cr, Ca, Fe, Ni, Mo, and rare earth elements.« less

Recovery of Mo for Accelerator Production of Mo-99 Using (y,n) Reaction on Mo-100

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tkac, Peter; Vandegrift, George F.; Nunn, Stephen D.

2013-09-30

Technetium-99m is a widely used radiopharmaceutical. Its parent, Mo-99, is produced worldwide to supply this important isotope. One means to produce Mo-99 is by bombarding a Mo-100 target with an electron beam from a linear accelerator; the γ/n reaction on Mo-100 produces Mo-99. After dissolving Mo-100 enriched disks in hydrogen peroxide, the solution is converted to potassium molybdate (0.2 g-Mo/mL) in 5 M KOH. After milking the Tc-99m in the TechneGen generator over a period of 7-10 days, the molybdenum solution needs to be treated to recover valuable Mo-100 for production of sintered Mo disks. However, during the production ofmore » Mo-99 by (γ, n) reaction on the Mo-100 target, several byproducts are formed. Therefore, recycling Mo will require the conversion of K 2MoO 4 in 5 M KOH solution to MoO 3 powder, and purification from other metals present in the Mo solution. The starting Mo-100 enriched material contains less than 20 mg of potassium in 1 kg of molybdenum (<20 ppm). However, after dissolving the irradiated Mo-100 target in hydrogen peroxide and converting it to K 2MoO 4 in 5 M KOH (0.2 g-Mo/mL), the solution contains about 1.8 kg of potassium per kilogram of molybdenum. The most challenging separation for this recovery step is purifying molybdenum from potassium. One requirement to facilitate the acceptance of the recycled material by the U.S. Food and Drug Administration (FDA) is that the impurities in the recycled material need to be at or below the levels present in the starting material. Therefore, the amount of potassium (K) in purified MoO 3 powder should be below 20 ppm; this will require a decontamination factor for removal of K to be ~1 × 10 5. Such a low K-contamination level will also prevent the production of large amounts of K-42 during irradiation of Mo-100. Based on economic concerns (due to the significant cost of enriched Mo-100) recycling Mo requires the conversion of K 2MoO 4 in a 5 M KOH solution to MoO 3 powder with high Mo recovery yields (>98%).« less

Use of published research in paediatric nutrition for the scientific substantiation of health claims referring to children's development and health.

PubMed

Valtueña Martínez, Silvia; Agostoni, Carlo

2013-10-01

The European Food Safety Authority (EFSA) provides policy makers with scientific and technical advice in relation to food safety and human nutrition in an independent and transparent way, and communicates such advice to the general public. Requirements for the scientific substantiation of health claims referring to children's development and health are the same as for other health claims. However, children (particularly infants) have peculiarities which should be taken into account, because these may impair the extrapolation of results to other groups. Health claims used in commercial communications should be authorized only after a scientific assessment of the highest possible standard by EFSA. EFSA's negative opinions on rejected claims should not be read as a criticism to research studies published in paediatric nutrition but rather highlight their limitations in relation to the substantiation of specific health claims made on foods. ©2013 Foundation Acta Paediatrica. Published by John Wiley & Sons Ltd.

Molybdenum-carbon bond dissociation energies in Mo(CO) sub 6

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ganske, J.A.; Rosenfeld, R.N.

1990-05-17

The pressure dependence of the recombination rate constants for Mo(CO){sub n} (n = 3,4 and 5) with CO has been studied by time-resolved infrared laser absorption spectroscopy. These data, in conjunction with an RRKM model for unimolecular decay of the activated molecules (Mo(CO){sub 6})*, (Mo(CO){sub 5})*, and (Mo(CO){sub 4})*, have allowed the determination of the bond dissociation energies for several of the Mo-C bonds in Mo(CO){sub 6}. The first Mo-C bond dissociation energies for Mo(CO){sub 6}, Mo(CO){sub 5}, and Mo(CO){sub 4} are found to be DH{degree}((CO){sub 5}Mo{hor ellipsis}CO) = 35 {plus minus} 5 kcal/mol, DH{degree}((CO){sub 4}Mo{hor ellipsis}CO) = 27 {plusmore » minus} 5 kcal/mol, and DH{degree}((CO){sub 3}Mo{hor ellipsis}CO) = 31 {plus minus} 5 kcal/mol.« less

Magnetic and electronic properties of single-walled Mo2C nanotube: a first-principles study

NASA Astrophysics Data System (ADS)

Jalil, Abdul; Sun, Zhongti; Wang, Dayong; Wu, Xiaojun

2018-04-01

The structural, electronic, and magnetic properties of single-walled Mo2C nanotubes are investigated by using first-principles calculations. We establish that single-walled Mo2C nanotubes can be rolled up from a graphene-like Mo2C monolayer with H- or T-type phase, i.e. H-Mo2C and T-Mo2C nanotubes. The armchair-type T-Mo2C nanotubes are more energetically stable than H-Mo2C nanotubes with the same diameter, while zigzag-type H-Mo2C nanotubes are more energetically stable than T-Mo2C nanotubes. In particular, (8, 0) H-Mo2C nanotube are more stable than Mo2C monolayer due to structural deformation. All Mo2C nanotubes are magnetic metals, independent of their chirality, and the magnetic moments of Mo atoms in the outer layer are larger than the inner. The ionic and metallic bonds in Mo2C nanotubes and delocalized electrons around Mo atoms lead to the versatile electronic and magnetic properties in them, endowing them potential applications in catalysts and electronics.

Magnetic and electronic properties of single-walled Mo2C nanotube: a first-principles study.

PubMed

Jalil, Abdul; Sun, Zhongti; Wang, Dayong; Wu, Xiaojun

2018-04-18

The structural, electronic, and magnetic properties of single-walled Mo 2 C nanotubes are investigated by using first-principles calculations. We establish that single-walled Mo 2 C nanotubes can be rolled up from a graphene-like Mo 2 C monolayer with H- or T-type phase, i.e. H-Mo 2 C and T-Mo 2 C nanotubes. The armchair-type T-Mo 2 C nanotubes are more energetically stable than H-Mo 2 C nanotubes with the same diameter, while zigzag-type H-Mo 2 C nanotubes are more energetically stable than T-Mo 2 C nanotubes. In particular, (8, 0) H-Mo 2 C nanotube are more stable than Mo 2 C monolayer due to structural deformation. All Mo 2 C nanotubes are magnetic metals, independent of their chirality, and the magnetic moments of Mo atoms in the outer layer are larger than the inner. The ionic and metallic bonds in Mo 2 C nanotubes and delocalized electrons around Mo atoms lead to the versatile electronic and magnetic properties in them, endowing them potential applications in catalysts and electronics.

Heat shock proteins MoSsb1, MoSsz1, and MoZuo1 attenuate MoMkk1-mediated CWI signaling and are important for growth and pathogenicity of Magnaporthe oryzae.

PubMed

Yang, Jie; Liu, Muxing; Liu, Xinyu; Yin, Ziyi; Sun, Yi; Zhang, Haifeng; Zheng, Xiaobo; Wang, Ping; Zhang, Zhengguang

2018-06-05

The mitogen-activated protein (MAP) kinase MoMkk1 governs the cell wall integrity (CWI) pathway in the rice blast fungus Magnaporthe oryzae. To understand the underlying mechanism, we have identified MoSsb1 as one of the MoMkk1-interacting proteins. MoSsb1 is a stress-seventy subfamily B (Ssb) protein homolog, sharing high amino acid sequence homology with the 70-kDa heat shock proteins (Hsp70s). Hsp70 proteins are a family of conserved and ubiquitously expressed chaperones that regulate protein biogenesis by promoting protein folding, preventing protein aggregation and controlling protein degradation. We found that MoSsb1 regulates the synthesis of nascent polypeptide chains and this regulation is achieved by being in complex with other members of heat shock proteins: Hsp70 MoSsz1 and 40-kDa heat shock protein (Hsp40) MoZuo1. MoSsb1 is important for the growth, conidiation and full virulence of the blast fungus and this role is also shared by MoSsz1 and MoZuo1. Importantly, MoSsb1, MoSsz1 and MoZuo1 are all involved in the regulation of the CWI MAP kinase pathway by modulating MoMkk1 biosynthesis. Our studies reveal novel insights into how MoSsb1, MoSsz1 and MoZuo1 affect CWI signaling that is involved in regulating growth, differentiation and virulence of M. oryzae and highlight the conserved functional mechanisms of Hsp proteins in pathogenic fungi.

Impact of reduced graphene oxide on MoS{sub 2} grown by sulfurization of sputtered MoO{sub 3} and Mo precursor films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pacley, Shanee, E-mail: shanee.pacley@us.af.mil; Brausch, Jacob; Beck-Millerton, Emory

2016-07-15

Monolayer molybdenum disulfide (MoS{sub 2}), a two dimensional semiconducting dichalcogenide material with a bandgap of 1.8–1.9 eV, has demonstrated promise for future use in field effect transistors and optoelectronics. Various approaches have been used for MoS{sub 2} processing, the most common being chemical vapor deposition. During chemical vapor deposition, precursors such as Mo, MoO{sub 3}, and MoCl{sub 5} have been used to form a vapor reaction with sulfur, resulting in thin films of MoS{sub 2}. Currently, MoO{sub 3} ribbons and powder, and MoCl{sub 5} powder have been used. However, the use of ribbons and powder makes it difficult to growmore » large area-continuous films. Sputtering of Mo is an approach that has demonstrated continuous MoS{sub 2} film growth. In this paper, the authors compare the structural properties of MoS{sub 2} grown by sulfurization of pulse vapor deposited MoO{sub 3} and Mo precursor films. In addition, they have studied the effects that reduced graphene oxide (rGO) has on MoS{sub 2} structure. Reports show that rGO increases MoS{sub 2} grain growth during powder vaporization. Herein, the authors report a grain size increase for MoS{sub 2} when rGO was used during sulfurization of both sputtered Mo and MoO{sub 3} precursors. In addition, our transmission electron microscopy results show a more uniform and continuous film growth for the MoS{sub 2} films produced from Mo when compared to the films produced from MoO{sub 3}. Atomic force microscopy images further confirm this uniform and continuous film growth when Mo precursor was used. Finally, x-ray photoelectron spectroscopy results show that the MoS{sub 2} films produced using both precursors were stoichiometric and had about 7–8 layers in thickness, and that there was a slight improvement in stoichiometry when rGO was used.« less

On the genesis of molybdenum carbide phases during reduction-carburization reactions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guil-Lopez, R., E-mail: rut.guil@icp.csic.es; Nieto, E.; Departamento de Tecnologia Quimica y Energetica, ESCET, Universidad Rey Juan Carlos, C/Tulipan s/n, 28933-Mostoles

2012-06-15

Molybdenum carbide has been prepared according to the carbothermal reduction method. Carbon black substrate was used as C-source whereas a H{sub 2}-flow was the reducing agent. Two different H{sub 2} consumption steps were identified during the carburization treatment. The low temperature step is related to the reduction of Mo{sup 6+}-to-Mo{sup 4+}, the higher temperature process accounts for the deep reduction of Mo{sup 4+}-to-metal Mo{sup 0} and its subsequent reaction with C to form the Mo-carbide. The influences of the maximum carburization temperature, carburization time, gas hourly space velocity regarding Mo-loading, heating rate and temperature of Ar pre-treatment were analyzed. Allmore » these conditions are interrelated to each other. Thus, the carburization process ends at 700 Degree-Sign C when Mo-loading is 10 wt%, however Mo-loading higher than 10 wt% requires higher temperatures. Carburization temperatures up to 800 Degree-Sign C are needed to fulfill Mo-carbide formation with samples containing 50 wt% Mo. Nevertheless, Ar pre-treatment at 550 Degree-Sign C and slow heating rates favor the carburization, thus requiring lower carburization temperatures to reach the same carburization level. - Graphical Abstract: H{sub 2}-consumption profile (TPR) during the molybdenum carburization process, XRD patterns of the reduced Mo-samples after carburization and TEM-micrographs with two different enlargement of the samples with 5, 20 and 50 wt% Mo. Highlights: Black-Right-Pointing-Pointer Control of carburization variables: tailor the reduced/carbide Mo-phases (single/mixture). Black-Right-Pointing-Pointer Mo carburization in two stages: (1) Mo{sup 6+}-Mo{sup 4+}; (2) Mo{sup 4+}-Mo{sup 0} and, at once, MoC. Black-Right-Pointing-Pointer The carburization process is faster than Mo{sup 4+} reduction. Black-Right-Pointing-Pointer XPS probed: reduced Mo particles show core-shell structure. Black-Right-Pointing-Pointer Core: reduced Mo (Mo{sub 2}C, MoO{sub 2} and/or Mo{sup 0}); Shell: 2-3 nm of MoO{sub 3}.« less

Charge Disproportionation in Tetragonal La 2MoO 5 , a Small Band Gap Semiconductor Influenced by Direct Mo–Mo Bonding

DOE PAGES

Colabello, Diane M.; Camino, Fernando E.; Huq, Ashfia; ...

2014-12-31

The structure of the novel compound La 2MoO 5 has been solved from powder X-ray and neutron diffraction data and belongs to the tetragonal space group P4/m (no. 83) with a = 12.6847(3) Å and c = 6.0568(2) Å and with Z = 8. It consists of equal proportions of bioctahedral (Mo 2O 10) and square prismatic (Mo 2O 8) dimers, both of which contain direct Mo-Mo bonds and are arranged in 1D chains. The Mo-Mo bond length in the Mo 2O 10dimers is 2.684(8) Å, while there are two types of Mo 2O 8 dimers with Mo-Mo bonds lengthsmore » of 2.22(2) and 2.28(2) Å. Although the average Mo oxidation state in La 2MoO 5 is 4+, the very different Mo-Mo distances reflect the fact that the Mo 2O 10 dimers contain only Mo5+ (d(1)), while the prismatic Mo2O8 dimers only contain Mo 3+ (d 3), a result directly confirmed by density function theory calculations. This is due to the complete disproportionation of Mo 4+, a phenomenon which has not previously been observed in solid-state compounds. La 2MoO 5 is diamagnetic, behavior which is not expected for a nonmetallic transition-metal oxide whose cation sites have an odd number of d-electrons. The resistivity displays the Arrhenius-type activated behavior expected for a semiconductor with a band gap of 0.5 eV, exhibiting an unusually small transport gap relative to other diamagnetic oxides. Diffuse reflectance studies indicate that La 2MoO 5 is a rare example of a stable oxide semiconductor with strong infrared absorbance. Lastly, we show that the d-orbital splitting associated with the Mo 2O 8 and Mo 2O 10 dimeric units can be rationalized using simple molecular orbital bonding concepts.« less

Recycle of enriched Mo targets for economic production of 99Mo/ 99mTc medical isotope without use of enriched uranium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tkac, Peter; Vandegrift, George F.

2015-08-09

A new recycle process for recovery of enriched 98Mo or 100Mo used for production of 99Mo/ 99mTc medical isotope was developed. In this process, Mo is precipitated from spent NorthStar Mo/Tc generator solution containing ~200 g/L Mo as K 2MoO 4 in 5 M KOH using acetic acid and then washed with nitric acid. High purification factors from potassium were achieved, and typical Mo recovery yields were ~95 %. In conclusion, the recycle process was performed with up to 260 g of Mo per batch and can be easily implemented for processing of up to 400 g of Mo.

A Reference Model for Sustainable E-Learning Service Systems: Experiences with the Joint University/Teradata Consortium

ERIC Educational Resources Information Center

Demirkan, Haluk; Goul, Michael; Gros, Mary

2010-01-01

Many e-learning service systems fail. This is particularly true for those sponsored by joint industry/university consortia where substantial economic investments are required up-front. This article provides an industry/university consortia reference model validated through experiences with the 8-year-old Teradata University Network. The reference…

"Nous" versus "on": Pronouns with First-Person Plural Reference in Synchronous French Chat

ERIC Educational Resources Information Center

van Compernolle, Remi A.

2008-01-01

This article explores variation in the use of the pronouns "nous" and "on" for first-person plural reference in a substantial corpus of French-language Internet chat discourse. The results indicate that "on" is nearly categorically preferred to "nous," which is in line with previous research on informal spoken French. A qualitative analysis of…

{Mo96La8} eggshell ring and self-assembly to {Mo132} Keplerate through Mo-blue intermediate, involved in UV-photolysis of [Mo7O24](6-)/carboxylic acid system at pH 4.

PubMed

Yamase, Toshihiro; Kumagai, Shun; Prokop, Petra V; Ishikawa, Eri; Tomsa, Adrian-Raul

2010-10-18

The prolonged UV-photolysis of aqueous solutions containing [Mo(7)O(24)](6-) and C(2)H(5)CO(2)H (as electron donor) at pH 3.9-4.1 generates the carboxylate-coordinated {Mo(132)} Keplerate (1a) isolated as a formamidinium/ammonium-mixed salt, [HC(NH(2))(2)](26)(NH(4))(28)[Mo(V)(60)Mo(VI)(72)O(372)(H(2)O)(48)(C(2)H(5)CO(2))(36)((i)C(3)H(7)CO(2))(6)]·16H(2)O (1), through the Mo-blue intermediate (2). The coordination of 2 to La(3+) gives rise to the formation of the chain structure of the C(2)-symmetric {Mo(96)La(8)} eggshell rings, formulated by H(22)[Mo(V)(20)Mo(VI)(76)O(301)(H(2)O)(29){La(H(2)O)(6)}(2)]{La(H(2)O)(5)}(6)]·54.5H(2)O (3). The eggshell-ring geometry results from the insertion of [Mo(VI)(2)O(7)(H(2)O)](2-) (spacer) into the equator outer ring of the wheel-shaped Mo-blue, and 10 {(Mo(VI))(Mo(VI)(5))} pentagonal subunits alternately above and below the equator outer ring are connected by eight La(3+) and two {Mo(VI)(2)} linkers within two inner rings. The neighboring eggshell rings are linked through two Mo-O-Mo bonds formed by dehydrative condensation between the {Mo(VI)(2)} linkers to result in the chain structure. Together with the results of the elemental analysis and IR, electronic absorption, (13)C NMR, and ESI-MS spectra for 2, the ring profile analysis of 3 let us identify 2 with a carbolylate-coordinated Mo-blue ring of high nuclearity. The Mo(VI)→Mo(V) photoreductive change of 2 to the 60-electron reduced Keplerate in the presence of C(2)H(5)CO(2)H involves both degradation of the outer ring and splitting of the binuclear linkers, which leads to the formation of [(Mo(VI))Mo(VI)(5)O(21)(H(2)O)(4)(carboxylate)](7-) pentagonal subunits and [Mo(V)(2)O(4)(carboxylate)](+)/[Mo(V)O(2)(carboxylate)(1/2)](0.5+)-mixed linkers for 1.

Nature's polyoxometalate chemistry: X-ray structure of the Mo storage protein loaded with discrete polynuclear Mo-O clusters.

PubMed

Kowalewski, Björn; Poppe, Juliane; Demmer, Ulrike; Warkentin, Eberhard; Dierks, Thomas; Ermler, Ulrich; Schneider, Klaus

2012-06-13

Some N(2)-fixing bacteria prolong the functionality of nitrogenase in molybdenum starvation by a special Mo storage protein (MoSto) that can store more than 100 Mo atoms. The presented 1.6 Å X-ray structure of MoSto from Azotobacter vinelandii reveals various discrete polyoxomolybdate clusters, three covalently and three noncovalently bound Mo(8), three Mo(5-7), and one Mo(3) clusters, and several low occupied, so far undefinable clusters, which are embedded in specific pockets inside a locked cage-shaped (αβ)(3) protein complex. The structurally identical Mo(8) clusters (three layers of two, four, and two MoO(n) octahedra) are distinguishable from the [Mo(8)O(26)](4-) cluster formed in acidic solutions by two displaced MoO(n) octahedra implicating three kinetically labile terminal ligands. Stabilization in the covalent Mo(8) cluster is achieved by Mo bonding to Hisα156-N(ε2) and Gluα129-O(ε1). The absence of covalent protein interactions in the noncovalent Mo(8) cluster is compensated by a more extended hydrogen-bond network involving three pronounced histidines. One displaced MoO(n) octahedron might serve as nucleation site for an inhomogeneous Mo(5-7) cluster largely surrounded by bulk solvent. In the Mo(3) cluster located on the 3-fold axis, the three accurately positioned His140-N(ε2) atoms of the α subunits coordinate to the Mo atoms. The formed polyoxomolybdate clusters of MoSto, not detectable in bulk solvent, are the result of an interplay between self- and protein-driven assembly processes that unite inorganic supramolecular and protein chemistry in a host-guest system. Template, nucleation/protection, and catalyst functions of the polypeptide as well as perspectives for designing new clusters are discussed.

Cholinergic regulation of the evoked quantal release at frog neuromuscular junction

PubMed Central

Nikolsky, Eugeny E; Vyskočil, František; Bukharaeva, Ella A; Samigullin, Dmitry; Magazanik, Lev G

2004-01-01

The effects of cholinergic drugs on the quantal contents of the nerve-evoked endplate currents (EPCs) and the parameters of the time course of quantal release (minimal synaptic latency, main modal value of latency histogram and variability of synaptic latencies) were studied at proximal, central and distal regions of the frog neuromuscular synapse. Acetylcholine (ACh, 5 × 10−4 m), carbachol (CCh, 1 × 10−5 m) or nicotine (5 × 10−6 m) increased the numbers of EPCs with long release latencies mainly in the distal region of the endplate (90–120 μm from the last node of Ranvier), where the synchronization of transmitter release was the most pronounced. The parameters of focally recorded motor nerve action potentials were not changed by either ACh or CCh. The effects of CCh and nicotine on quantal dispersion were reduced substantially by 5 × 10−7 m (+)tubocurarine (TC). The muscarinic agonists, oxotremorine and the propargyl ester of arecaidine, as well as antagonists such as pirenzepine, AF-DX 116 and methoctramine, alone or in combination, did not affect the dispersion of the release. Muscarinic antagonists did not block the dispersion action of CCh. Cholinergic drugs either decreased the quantal content mo (muscarinic agonist, oxotremorine M, and nicotinic antagonist, TC), or decreased mo and dispersed the release (ACh, CCh and nicotine). The effects on mo were not related either to the endplate region or to the initial level of release dispersion. It follows that the mechanisms regulating the amount and the time course of transmitter release are different and that, among other factors, they are altered by presynaptic nicotinic receptors. PMID:15254150

Colony impact of pesticide-induced sublethal effects on honeybee workers: A simulation study using BEEHAVE.

PubMed

Thorbek, Pernille; Campbell, Peter J; Thompson, Helen M

2017-03-01

Research on neonicotinoids and honeybees have changed focus from direct mortality to sublethal effects. In the present study, a published honeybee model, BEEHAVE, is used to compare induced colony level impact of pesticides including direct mortality, poor brood care, disorientation, and increased handling time in oilseed rape and sunflower crops. Actual effects on individual bees will depend on exposure concentrations, but in the present study large effects were enforced. In oilseed rape, poor brood care had the largest colony impact, because it created a bottleneck for spring build-up of the workforce, and colony impact for all effect types peaked 1 mo after exposure ceased. In sunflower, the later exposure changed the response so colony impact peaked during exposure, and the bottleneck was honey store build-up. In all scenarios, good forage mitigated effects substantially. It is concluded that field studies should continue at least 1 mo after exposure to ensure detection of ecologically relevant sublethal effects. The results indicated that even if a sublethal effect is difficult to detect in the field, subsequent ecologically relevant colony level impacts would be clear if studies are continued for 1 mo after exposure. Guidance for regulatory studies recommends extended observation periods, and published field studies already use extended observation periods, so it is concluded that current methods are adequate for detecting ecologically relevant sublethal effects. Although published laboratory and semifield studies conducted under controlled exposure conditions suggest that sublethal effects may occur, published field studies with neonicotinoid seed treatments, naturally foraging bees, and extended observation periods do not report colony-level effects, suggesting that in these studies no ecologically relevant sublethal effects occurred. Environ Toxicol Chem 2017;36:831-840. © 2016 SETAC. © 2016 SETAC.

Possibilities and considerations when merging dietary data from the world's two largest pregnancy cohorts: the Danish National Birth Cohort and the Norwegian Mother and Child Cohort Study.

PubMed

Olsen, Sjurdur F; Birgisdottir, Bryndis Eva; Halldorsson, Thorhallur I; Brantsaeter, Anne Lise; Haugen, Margaretha; Torjusen, Hanne; Petersen, Sesilje B; Strøm, Marin; Meltzer, Helle Margrete

2014-11-01

To elucidate the research possibilities when merging data on maternal diet from the Danish National Birth Cohort (DNBC) and the Norwegian Mother and Child Cohort Study (MoBa), through comparison of (i) the methodology used for dietary assessment and (ii) the estimated intake of selected food groups in the two cohorts. Qualitative and quantitative comparison of the two dietary databases. Two national prospective pregnancy cohorts. Denmark, Norway. Comparison of food intake using food frequency questionnaires (FFQs). The FFQs had overlapping time windows and a majority of the questions in the two FFQs were comparable. Calculation principles shared similar features, including the software used and use of global questions to calibrate intakes of different food groups. A total of 63 food groups were defined that could be compared across the two cohorts; these were further aggregated down to 31 broader groups. A comparison of food intakes (grams/d) showed 39, 74 and 141% lower daily intakes of fish, potatoes and rice, respectively, in DNBC vs. MoBa and 39, 54 and 65% higher daily intakes of milk, butter and potatoes in DNBC vs. MoBa. For most other food groups, differences in consumption data were below 20%. The two FFQs are to a large extent compatible and substantial differences in dietary habits were observed between the two cohorts. This may strengthen studies using pooled analysis to examine diet-disease relations. This is a conclusion of great importance given the colossal and costly task involved to establish each of these two cohorts. © 2014 Nordic Federation of Societies of Obstetrics and Gynecology.

The effect of heat waves on dairy cow mortality.

PubMed

Vitali, A; Felici, A; Esposito, S; Bernabucci, U; Bertocchi, L; Maresca, C; Nardone, A; Lacetera, N

2015-07-01

This study investigated the mortality of dairy cows during heat waves. Mortality data (46,610 cases) referred to dairy cows older than 24mo that died on a farm from all causes from May 1 to September 30 during a 6-yr period (2002-2007). Weather data were obtained from 12 weather stations located in different areas of Italy. Heat waves were defined for each weather station as a period of at least 3 consecutive days, from May 1 to September 30 (2002-2007), when the daily maximum temperature exceeded the 90th percentile of the reference distribution (1971-2000). Summer days were classified as days in heat wave (HW) or not in heat wave (nHW). Days in HW were numbered to evaluate the relationship between mortality and length of the wave. Finally, the first 3 nHW days after the end of a heat wave were also considered to account for potential prolonged effects. The mortality risk was evaluated using a case-crossover design. A conditional logistic regression model was used to calculate odds ratio and 95% confidence interval for mortality recorded in HW compared with that recorded in nHW days pooled and stratified by duration of exposure, age of cows, and month of occurrence. Dairy cows mortality was greater during HW compared with nHW days. Furthermore, compared with nHW days, the risk of mortality continued to be higher during the 3 d after the end of HW. Mortality increased with the length of the HW. Considering deaths stratified by age, cows up to 28mo were not affected by HW, whereas all the other age categories of older cows (29-60, 61-96, and >96mo) showed a greater mortality when exposed to HW. The risk of death during HW was higher in early summer months. In particular, the highest risk of mortality was observed during June HW. Present results strongly support the implementation of adaptation strategies which may limit heat stress-related impairment of animal welfare and economic losses in dairy cow farm during HW. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

A grape-enriched diet increases bone calcium retention and cortical bone properties in ovariectomized rats.

PubMed

Hohman, Emily E; Weaver, Connie M

2015-02-01

Grapes and their associated phytochemicals have been investigated for beneficial effects on cardiovascular health, cancer prevention, and other chronic diseases, but the effect of grape consumption on bone health has not been fully determined. We previously found short-term benefits of grape products on reducing bone turnover in ovariectomized rats. The objective of this study was to determine the long-term benefits of a grape-enriched diet on bone in ovariectomized rats. Rats were ovariectomized at 3 mo of age and were administered a single dose of (45)Ca to prelabel bones at 4 mo of age. After a 1-mo equilibration period, baseline urinary (45)Ca excretion was determined. Rats (n = 22/group) were then randomly assigned to a modified AIN93M diet containing 25% freeze-dried grape powder or to a control diet for 8 wk. Urinary (45)Ca excretion was monitored throughout the study to determine changes in bone (45)Ca retention. Calcium balance was assessed after 1 and 8 wk of consuming the experimental diets, and a calcium kinetic study was performed at 8 wk. After 8 wk, femurs were collected for micro-computed tomographic imaging, 3-point bending, and reference point indentation. Rats fed the grape-enriched diet had 44% greater net bone calcium retention than did rats fed the control diet. There were no differences in calcium balance due to diet at either week 1 or week 8, but there was a significant increase in net calcium absorption (10.6%) and retention (5.7%) from week 1 to week 8 in the grape-enriched diet group only. Grape-enriched diet-fed rats had 3% greater cortical thickness and 11% greater breaking strength. There were no differences in femur bone mineral density, trabecular microarchitecture, or reference point indentation variables due to diet. This study of ovariectomized rats indicates that the consumption of grape products may improve calcium utilization and suppress bone turnover, resulting in improvements in bone quality. © 2015 American Society for Nutrition.

[Application of ICP-MS in evaluating element contamination in soils].

PubMed

Wu, Ying-juan; Chen, Yong-heng; Yang, Chun-xia; Chang, Xiang-yang

2008-12-01

The Yunfu pyrite was the second biggest pyrite bed in the world. Plants using industrial ore of the Yunfu pyrite are distributed in many sections across the country. In the present paper, elements V, Cr, Co, Cu, Zn, Mo, Cd, Sb, Rb and Cs in soil profiles in slag disposing area of a sulfuric acid plant using industrial ore of theYunfu pyrite were studied. A method for simultaneously determination of metals and some reference elements in soils by ICP-MS was developed. The correlations between the metals and their reference elements were fast found. Enrichment factors were applied for evaluating the degree of soil contamination, and the problem about choosing contamination elements background values was pointed out. The results indicated that element V showed apparent and serious pollution, The Co showed middle degree pollution, and there has been a trend of apparent pollution. The Cr, Mo and Cd showed pollution between light degree and middle degree. The Zn and Sb showed light degree pollution, and there was a latent trend of middle degree pollution. The Cu showed light degree pollution. The high enrichment points of the V and the Cr were observed in the upper part (4.0-10.5 cm) and deep part of soil profiles (44.0-75.5 cm). Those of Co and Mo were found in the surface of soil profiles (0-5.0 cm), middle-upper part (9.5-10.5 cm) and middle part (29.5-46.0 cm), while those of Cd and Cu occurred just in the middle of soil profiles (29.5-46.0 cm). The formation of highly enrichment points of contamination elements in the soil profiles was the result of leaching and accumulating effect of the metals released from slag and the residual metals of highly weathered red soils. Most of pollution of V in the soil was contributed by the V in soil bed. Part of the V pollution in the soil was supplied by leaching and accumulating effect of the V which came from catalyst with lost activity in sulfuric acid production volatilizing into slag.

Properties of Superconducting Mo, Mo2n and Trilayer Mo2n-Mo-Mo2n Thin Films

NASA Technical Reports Server (NTRS)

Barrentine, E. M.; Stevenson, T. R.; Brown, A. D.; Lowitz, A. E.; Noroozian, O.; U-Yen, K.; Eshan, N.; Hsieh, W. T.; Moseley, S. H.; Wollack, E. J.

2014-01-01

We present measurements of the properties of thin film superconducting Mo, Mo2N and Mo2N/Mo/Mo2N trilayers of interest for microwave kinetic inductance detector (MKID) applications. Using microwave resonator devices, we investigate the transition temperature, energy gaps, kinetic inductance, and internal quality factors of these materials. We present an Usadel-based interpretation of the trilayer transition temperature as a function of trilayer thicknesses, and a 2-gap interpretation to understand the change in kinetic inductance and internal resonance quality factor (Q) as a function of temperature.

Hot cell purification of strontium-82, 85 and other isotopes from proton irradiated molybdenum

DOEpatents

Bentley, G.E.; Barnes, J.W.

1979-10-17

A process suitable for producing curie quantities of quite pure Sr-82,85 is given. After a Mo target is irradiated with energetic protons having energies greater than about 200 MeV, thus producing a large number of radioactive species, the particular species of Sr-82,85 are substantially separated from the other products by a 6-step process. The process comprises dissolution of the target in H/sub 2/O/sub 2/, followed by use of several ion exchange resins, extraction with an organophosphorus compound, and several adjustments of pH values. Other embodiments include processes for producing relatively pure long-lived Rb isotopes, Y-88, and Zr-88.

Hot cell purification of strontium-82, 85 and other isotopes from proton irradiated molybdenum

DOEpatents

Bentley, Glenn E.; Barnes, John W.

1981-01-01

A process suitable for producing curie quantities of quite pure Sr-82,85 is given. After a Mo target is irradiated with energetic protons having energies greater than about 200 MeV, thus producing a large number of radioactive species, the particular species of Sr-82,85 are substantially separated from the other products by a 6-step process. The process comprises dissolution of the target in H.sub.2 O.sub.2, followed by use of several ion exchange resins, extraction with an organophosphorus compound, and several adjustments of pH values. Other embodiments include processes for producing relatively pure long-lived Rb isotopes, Y-88, and Zr-88.

The cause of welding cracks in aircraft steels

NASA Technical Reports Server (NTRS)

Muller, J

1940-01-01

The discussion in this article refers to gas welding of thin-walled parts of up to about 3 mm thickness. It was proven that by restricting the sulphur, carbon, and phosphorous content, and by electric-furnace production of the steel, it was possible in a short time to remove this defect. Weld hardness - i.e., martensite formation and hardness of the overheated zone - has no connection with the tendency to weld-crack development. Si, Cr, Mo, or V content has no appreciable effect, while increased manganese content tends to reduce the crack susceptibility.

Applying a Physics-Based Description of Fatigue Variability Behavior to Probabilistic Life Prediction (Preprint)

DTIC Science & Technology

2007-07-01

predicted at lower stress levels as illustrated for the α+β titanium alloy, Ti-6Al-2Sn-4Zr-6Mo (Ti- 6 -2- 4 - 6 ), in Fig. 2((a) and (b)) [7, 8]. The...variability by a bimodal probability density representing the superposition of these dual mechanisms with reference to the α+β titanium alloy, Ti- 6 -2- 4 - 6 ...these trends. 7 The alternate description is illustrated with respect to the α+β titanium alloy, Ti- 6 -2- 4 - 6 . The stress vs. total lifetime behavior

Density of tumor-infiltrating lymphocytes correlates with extent of brain edema and overall survival time in patients with brain metastases

PubMed Central

Berghoff, Anna S; Fuchs, Elisabeth; Ricken, Gerda; Mlecnik, Bernhard; Bindea, Gabriela; Spanberger, Thomas; Hackl, Monika; Widhalm, Georg; Dieckmann, Karin; Prayer, Daniela; Bilocq, Amelie; Heinzl, Harald; Zielinski, Christoph; Bartsch, Rupert; Birner, Peter; Galon, Jerome; Preusser, Matthias

2016-01-01

The immune microenvironment of the brain differs from that of other organs and the role of tumor-infiltrating lymphocytes (TILs) in brain metastases (BM), one of the most common and devastating complication of cancer, is unclear. We investigated TIL subsets and their prognostic impact in 116 BM specimens using immunohistochemistry for CD3, CD8, CD45RO, FOXP3, PD1 and PD-L1. The Immunoscore was calculated as published previously. Overall, we found TIL infiltration in 115/116 (99.1%) BM specimens. PD-L1 expression was evident in 19/67 (28.4%) BM specimens and showed no correlation with TIL density (p > 0.05). TIL density was not associated with corticosteroid administration (p > 0.05). A significant difference in infiltration density according to TIL subtype was present (p < 0.001; Chi Square); high infiltration was most frequently observed for CD3+ TILs (95/116; 81.9%) and least frequently for PD1+ TILs (18/116; 15.5%; p < 0.001). Highest TIL density was observed in melanoma, followed by renal cell cancer and lung cancer BM (p < 0.001). The density of CD8+ TILs correlated positively with the extent of peritumoral edema seen on pre-operative magnetic resonance imaging (p = 0.031). The density of CD3+ (15 vs. 6 mo; p = 0.015), CD8+ (15 vs. 11 mo; p = 0.030) and CD45RO+ TILs (18 vs. 8 mo; p = 0.006) showed a positive correlation with favorable median OS times. Immunoscore showed significant correlation with survival prognosis (27 vs. 10 mo; p < 0.001). The prognostic impact of Immunoscore was independent from established prognostic parameters at multivariable analysis (HR 0.612, p < 0.001). In conclusion, our data indicate that dense TILs infiltrates are common in BM and correlate with the amount of peritumoral brain edema and survival prognosis, thus identifying the immune system as potential biomarker for cancer patients with CNS affection. Further studies are needed to substantiate our findings. PMID:26942067

The expression of keratins, vimentin, neurofilament proteins, smooth muscle actin, neuron-specific enolase, and synaptophysin in tumors of the specific glands in the canine anal region.

PubMed

Vos, J H; van den Ingh, T S; Ramaekers, F C; Molenbeek, R F; de Neijs, M; van Mil, F N; Ivanyi, D

1993-07-01

Eight canine tumors originating from specific glandular structures in the anal region, as well as metastatic tumor tissue of two of these cases (case Nos. 7, 8), were immunohistochemically analyzed using various monoclonal antibodies (MoAbs) directed against human keratin types, vimentin, neurofilament proteins, and alpha-smooth muscle actin. These tumors also were stained for the broad-spectrum neuroendocrine markers neuron-specific enolase (NSE) and synaptophysin. In histologically normal canine anal structures, alpha-smooth muscle actin and NSE antibodies stained basally localized (probably myoepithelial) cells in the anal glands and the anal sac glands. NSE staining also was present in a limited number of luminal cells in both anal glands and anal sac glands. Synaptophysin labeling was not observed in any of these glandular structures. Histologically, the tumors were differentiated into well- and moderately differentiated perianal gland tumors (n = 5) and carcinomas without perianal gland differentiation (n = 3), corresponding to the so-called apocrine carcinomas of the anal region. Immunohistochemically, the perianal gland tumors could be differentiated from the carcinomas by marked differences in staining pattern with the various keratin MoAbs, particularly MoAbs directed against human keratin types 7 and 18. The keratin-staining characteristics of the carcinomas suggest a glandular luminal cell origin. Metastases of the carcinomas showed loss of some keratin-staining characteristics as compared with the primary tumor. Staining for NSE was only observed in solitary cells and small cell clusters in the carcinomas and their metastases, whereas the alpha-smooth muscle actin antibody did not react with the carcinoma cells. None of the tumors stained for neurofilament proteins or synaptophysin. An unequivocal neuroendocrine nature of the carcinomas could not be substantiated by our immunohistochemical study, although the presence of a population of neuroendocrine cells within these neoplasms seems likely. Because the immunohistochemical features of the carcinomas with respect to various keratin MoAbs and NSE are similar to those of the anal glands and the anal sac glands, both these glands might be considered as site of origin of these carcinomas.

Which imaging modality is most effective for identifying pseudotumours in metal-on-metal hip resurfacings requiring revision: ultrasound or MARS-MRI or both?

PubMed

Matharu, G S; Mansour, R; Dada, O; Ostlere, S; Pandit, H G; Murray, D W

2016-01-01

The aims of this study were to compare the diagnostic test characteristics of ultrasound alone, metal artefact reduction sequence MRI (MARS-MRI) alone, and ultrasound combined with MARS-MRI for identifying intra-operative pseudotumours in metal-on-metal hip resurfacing (MoMHR) patients undergoing revision surgery. This retrospective diagnostic accuracy study involved 39 patients (40 MoMHRs). The time between imaging modalities was a mean of 14.6 days (0 to 90), with imaging performed at a mean of 5.3 months (0.06 to 12) before revision. The prevalence of intra-operative pseudotumours was 82.5% (n = 33). Agreement with the intra-operative findings was 82.5% (n = 33) for ultrasound alone, 87.5% (n = 35) for MARS-MRI alone, and 92.5% (n = 37) for ultrasound and MARS-MRI combined. The diagnostic characteristics for ultrasound alone and MARS-MRI alone reached similar sensitivities (90.9% vs 93.9%) and positive predictive values (PPVs; 88.2% vs 91.2%), but higher specificities (57.1% vs 42.9%) and negative predictive values (NPVs; 66.7% vs 50.0%) were achieved with MARS-MRI. Ultrasound and MARS-MRI combined produced 100% sensitivity and 100% NPV, whilst maintaining both specificity (57.1%) and PPV (91.7%). For the identification of a pseudotumour, which was confirmed at revision surgery, agreement was substantial for ultrasound and MARS-MRI combined (κ = 0.69), moderate for MARS-MRI alone (κ = 0.54), and fair for ultrasound alone (κ = 0.36). These findings suggest that ultrasound and/or MARS-MRI have a role when assessing patients with a MoMHR, with the choice dependent on local financial constraints and the availability of ultrasound expertise. However in patients with a MoMHR who require revision, combined imaging was most effective. Combined imaging with ultrasound and MARS-MRI always identified intra-operative pseudotumours if present. Furthermore, if neither imaging modality showed a pseudotumour, one was not found intra-operatively. ©2016 The British Editorial Society of Bone & Joint Surgery.

Ca, Sr, Mo and U isotopes evidence ocean acidification and deoxygenation during the Late Permian mass extinction

NASA Astrophysics Data System (ADS)

Silva-Tamayo, Juan Carlos; Payne, Jon; Wignall, Paul; Newton, Rob; Eisenhauer, Anton; Weyer, Stenfan; Neubert, Nadja; Lau, Kim; Maher, Kate; Paytan, Adina; Lehrmann, Dan; Altiner, Demir; Yu, Meiyi

2014-05-01

The most catastrophic extinction event in the history of animal life occurred at the end of the Permian Period, ca. 252 Mya. Ocean acidification and global oceanic euxinia have each been proposed as causes of this biotic crisis, but the magnitude and timing of change in global ocean chemistry remains poorly constrained. Here we use multiple isotope systems - Ca, Sr, Mo and U - measured from well dated Upper Permian- Lower Triassic sedimentary sections to better constrain the magnitude and timing of change in ocean chemistry and the effects of ocean acidification and de-oxygenation through this interval. All the investigated carbonate successions (Turkey, Italy and China) exhibit decreasing δ44/40Ca compositions, from ~-1.4‰ to -2.0‰ in the interval preceding the main extinction. These values remain low during most of the Griesbachian, to finally return to -1.4‰ in the middle Dienerian. The limestone succession from southern Turkey also displays a major decrease in the δ88/86Sr values from 0.45‰ to 0.3‰ before the extinction. These values remain low during the Griesbachian and finally increase to 0.55‰ by the middle Dienerian. The paired negative anomalies on the carbonate δ44/40Ca and δ88/86Sr suggest a decrease in the carbonate precipitation and thus an episode of ocean acidification coincident with the major biotic crisis. The Mo and U isotope records also exhibit significant rapid negative anomalies at the onset of the main extinction interval, suggesting rapid expansion of anoxic and euxinic marine bottom waters during the extinction interval. The rapidity of the isotope excursions in Mo and U suggests substantially reduced residence times of these elements in seawater relative to the modern, consistent with expectations for a time of widespread anoxia. The large C-isotope variability within Lower Triassic rocks, which is similar to that of the Lower-Middle Cambrian, may reflect biologically controlled perturbations of the oceanic carbon cycle. These findings strengthen the evidence for a global ocean acidification event coupled with rapid expansion of anoxic zones as drivers of end-Permian extinction in the oceans.

OPAL: prediction of MoRF regions in intrinsically disordered protein sequences.

PubMed

Sharma, Ronesh; Raicar, Gaurav; Tsunoda, Tatsuhiko; Patil, Ashwini; Sharma, Alok

2018-06-01

Intrinsically disordered proteins lack stable 3-dimensional structure and play a crucial role in performing various biological functions. Key to their biological function are the molecular recognition features (MoRFs) located within long disordered regions. Computationally identifying these MoRFs from disordered protein sequences is a challenging task. In this study, we present a new MoRF predictor, OPAL, to identify MoRFs in disordered protein sequences. OPAL utilizes two independent sources of information computed using different component predictors. The scores are processed and combined using common averaging method. The first score is computed using a component MoRF predictor which utilizes composition and sequence similarity of MoRF and non-MoRF regions to detect MoRFs. The second score is calculated using half-sphere exposure (HSE), solvent accessible surface area (ASA) and backbone angle information of the disordered protein sequence, using information from the amino acid properties of flanks surrounding the MoRFs to distinguish MoRF and non-MoRF residues. OPAL is evaluated using test sets that were previously used to evaluate MoRF predictors, MoRFpred, MoRFchibi and MoRFchibi-web. The results demonstrate that OPAL outperforms all the available MoRF predictors and is the most accurate predictor available for MoRF prediction. It is available at http://www.alok-ai-lab.com/tools/opal/. ashwini@hgc.jp or alok.sharma@griffith.edu.au. Supplementary data are available at Bioinformatics online.

The First Molybdenum(VI) and Tungsten(VI) Oxoazides MO2(N3)2, MO2(N3)2⋅2 CH3CN, (bipy)MO2(N3)2, and [MO2(N3)4](2-) (M=Mo, W).

PubMed

Haiges, Ralf; Skotnitzki, Juri; Fang, Zongtang; Dixon, David A; Christe, Karl O

2015-08-10

Molybdenum(VI) and tungsten(VI) dioxodiazide, MO2(N3)2 (M=Mo, W), were prepared through fluoride-azide exchange reactions between MO2F2 and Me3SiN3 in SO2 solution. In acetonitrile solution, the fluoride-azide exchange resulted in the isolation of the adducts MO2(N3)2⋅2 CH3CN. The subsequent reaction of MO2(N3)2 with 2,2'-bipyridine (bipy) gave the bipyridine adducts (bipy)MO2(N3)2. The hydrolysis of (bipy)MoO2(N3)2 resulted in the formation and isolation of [(bipy)MoO2N3]2O. The tetraazido anions [MO2(N3)4](2-) were obtained by the reaction of MO2(N3)2 with two equivalents of ionic azide. Most molybdenum(VI) and tungsten(VI) dioxoazides were fully characterized by their vibrational spectra, impact, friction, and thermal sensitivity data and, in the case of (bipy)MoO2(N3)2, (bipy)WO2(N3)2, [PPh4]2[MoO2(N3)4], [PPh4]2[WO2(N3)4], and [(bipy)MoO2N3]2O by their X-ray crystal structures. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis of MoS2 and MoO2 for their applications in H2 generation and lithium ion batteries: a review.

PubMed

Zhao, Yufei; Zhang, Yuxia; Yang, Zhiyu; Yan, Yiming; Sun, Kening

2013-08-01

Scientists increasingly witness the applications of MoS 2 and MoO 2 in the field of energy conversion and energy storage. On the one hand, MoS 2 and MoO 2 have been widely utilized as promising catalysts for electrocatalytic or photocatalytic hydrogen evolution in aqueous solution. On the other hand, MoS 2 and MoO 2 have also been verified as efficient electrode material for lithium ion batteries. In this review, the synthesis, structure and properties of MoS 2 and MoO 2 are briefly summarized according to their applications for H 2 generation and lithium ion batteries. Firstly, we overview the recent advancements in the morphology control of MoS 2 and MoO 2 and their applications as electrocatalysts for hydrogen evolution reactions. Secondly, we focus on the photo-induced water splitting for H 2 generation, in which MoS 2 acts as an important co-catalyst when combined with other semiconductor catalysts. The newly reported research results of the significant functions of MoS 2 nanocomposites in photo-induced water splitting are presented. Thirdly, we introduce the advantages of MoS 2 and MoO 2 for their enhanced cyclic performance and high capacity as electrode materials of lithium ion batteries. Recent key achievements in MoS 2 - and MoO 2 -based lithium ion batteries are highlighted. Finally, we discuss the future scope and the important challenges emerging from these fascinating materials.

Solution processable mixed-solvent exfoliated MoS2 nanosheets for efficient and robust organic light-emitting diodes

NASA Astrophysics Data System (ADS)

Liu, Chia-Wei; Wang, Chia; Liao, Chia-Wei; Golder, Jan; Tsai, Ming-Chih; Young, Hong-Tsu; Chen, Chin-Ti; Wu, Chih-I.

2018-04-01

We demonstrate the use of solution-processed molybdenum trioxide (MoO3) nanoparticle-decorated molybdenum disulfide (MoS2) nanosheets (MoS2/MoO3) as hole injection layer (HIL) in organic lighting diodes (OLEDs). The device performance is shown to be significantly improved by the introduction of such MoS2/MoO3 HIL without any post-ultraviolet-ozone treatment, and is shown to better the performance of devices fabricated using conventional poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) and MoO3 nanoparticle HILs. The MoS2/MoO3 nanosheets form a compact film, as smooth as PEDOT:PSS films and smoother than MoO3 nanoparticle films, when simply spin-coated on indium tin oxide substrates. The improvement in device efficiency can be attributed to the smooth surface of the nanostructured MoS2/MoO3 HIL and the excellent conductivity characteristics of the two-dimensional (2D) layered material (MoS2), which facilitate carrier transport in the device and reduce the sheet resistance. Moreover, the long-term stability of OLED devices that use such MoS2/MoO3 layers is shown to be improved dramatically compared with hygroscopic and acidic PEDOT:PSS-based devices.

Molybdenum Enrichment in the 3.2 Ga old Black Shales Recovered by Dixon Island-Cleaverville Drilling Project (DXCL-DP) in Northwestern Pilbara, Western Australia

NASA Astrophysics Data System (ADS)

Yamaguchi, K. E.; Kiyokawa, S.; Naraoka, H.; Ikehara, M.; Ito, T.; Suganuma, Y.; Sakamoto, R.; Hosoi, K.

2010-12-01

To obtain drillcores of Mesoarchean black shales with negligible modern weathering, we conducted continental drilling at Cleaverville coast in Pilbara, Western Australia. We recovered 3.2Ga sulfidic black shales of the Cleaverville Group from three drillholes (~200m in total), namely DX, CL1, and CL2. Information on the geology of the drilling site has been reported [1, 2]. Here we report the discovery of Mo enrichment in the 3.2Ga DXCL-DP black shales. We analyzed total chemical compositions of forty black shale samples from drillcore DX and fifty-six of those from CL1 and CL2. Molybdenum concentrations for DX samples ranged from 0.3 to 12.9ppm (Avg±1σ= 1.8±1.9ppm), and those for CL1 and CL2 (combined) ranged from 0.8 to 3.3ppm (Avg±1σ= 1.4±0.4ppm). The highest concentration of Mo occurs in Corg-rich sample, and is comparable to that of the contemporaneous Fig Tree Group in South Africa [3, 4]. The highest concentration of Mo in the DXCL-DP samples, ~13ppm, is lower than that found in the 2.5 Ga Mt. McRae Shale of the Hamersley Group, Western Australia (maximums are ~17ppm [5], and ~40ppm [6]). However, it is much higher, by thirteen times, than the average Mo concentration in the Phanerozoic shales (1ppm [7]). No significant enrichment of Mo was expected to occur in the before-GOE black shales if pO2 was as low as <10-6 PAL. Sulfur isotope analysis revealed, based on the variable δ34S values (-1.9 ~ +26.8‰), that bacterial sulfate reduction was so extensive in the 3.2Ga deep marine environments that sulfate utilization by sulfate-reducers was near completion [8]. Production of bacteriogenic sulfide would have enhanced fixation of dissolved Mo into sulfide minerals in sediments. This is rather a common process occurring in oxygen-depleted environments in the modern ocean ([9]). A combined enrichment of Mo, Corg, and S, together with high δ34S values for a sedimentary formation may be used as a strong evidence for operation of modern-day style sedimentary Mo enrichment. This further implies that oxygenation of the atmosphere and (at least the surface) oceans was significant during deposition of the sediments, ~800Ma earlier than commonly thought ([10]). Operation of present-day style geochemical cycle of Mo in the Mesoarchean surface environments suggests early evolution of atmosphere, oceans, and microbial biosphere. References: [1] Kiyokawa et al, 2006, GSAB 118: 3-22. [2] Yamaguchi et al, 2009, Sci. Drill. 7: 34-37. [3] Yamaguchi, 2002, Ph.D. dissertation, Penn State Univ. [4] Yamaguchi & Ohmoto, 2002, GSA Abstract [5] Naraoka et al, 2001, 4th Int'l Archaean Symp., Perth. [6] Anbar et al, 2007, Science 317: 1903-1906. [7] Vine & Tourtelot, 1970, Econ. Geol. 65: 253-272. [8] Sakamoto et al, 2010, Fall AGU Mtg. [9] Morford & Emerson, 1999, GCA 63: 1735-1750. [10] Bekker et al, 2004, Nature 427: 117-120.

X-ray Diffraction Study of Molybdenum to 900 GPa

NASA Astrophysics Data System (ADS)

Wang, J.; Coppari, F.; Smith, R.; Eggert, J.; Boehly, T.; Collins, G. W.; Duffy, T. S.

2013-12-01

Molybdenum (Mo) is a transition metal that is important as a high-pressure standard. Its equation of state, structure, and melting behavior have been explored extensively in both experimental and theoretical studies. Melting data up to the Mbar pressure region from static compression experiments in the diamond anvil cell [Errandonea et al. 2004] are inconsistent with shock wave sound velocity measurements [Hixson et al., 1989]. There are also conflicting reports as to whether body-centered cubic (BCC) Mo transforms to a face-centered cubic (FCC), hexagonal close packed (HCP) or double hexagonal close packed (DHCP) structure at either high pressure or high pressure and temperature conditions [Belonoshko et al. 2008, Mikhaylushkin et al., 2008 and Cazorla et al., 2008]. Recently, a phase transition from BCC to the DHCP phase at 660 GPa and 0 K was predicted using the particle swam optimization (PSO) method (Wang et al, 2013). Here we report an x-ray diffraction study of dynamically compressed molybdenum. Experiments were conducted using the Omega laser at the Laboratory for Laser Energetics at the University of Rochester. Mo targets were either ramp or shock compressed using a laser drive. In ramp loading, the sample is compressed sufficiently slowly that a shock wave does not form. This results in lower temperatures, keeping the sample in the solid state to higher pressures. X-ray diffraction measurements were performed using quasi-monochromatic x-rays from a highly ionized He-α Cu source and image plate detectors. Upon ramp compression, we found no evidence of phase transition in solid Mo up to 900 GPa. The observed peaks can be assigned to the (110) and (200) or (220) reflections of BCC Mo up to the highest pressure, indicating that Mo does not melt under ramp loading to maximum pressure reached. Under shock loading, we did not observe any evidence for the solid-solid phase transformation around 210 GPa as reported in previous work (Hixson et al, 1989). The BCC phase of Mo remained stable along the Hugoniot up to at least 350 GPa. Our observation of diffraction peaks from shocked Mo shows that Hugoniot does not cross the melting curve until at least this pressure. This indicates that previous diamond cell experiments (Errandonea et al., 2004) have underestimated the Mo melting curve. We acknowledge the Omega staff at LLE for their assistance, and the Target Engineering Team at LLNL for fabrication of the targets used in these experiments. The research was supported by NNSA/DOE through the National Laser Users' Facility Program under contracts DE-NA0000856 and DE-FG52-09NA29037. References: [1] R.S. Hixson, D.A. Boness, and J.W. Shaner, Phys. Rev. Lett., 62, 637 (1989). [2] D. Errandonea, B. Schwager, R. Ditz, C. Gessmann, R. Boehler, and M. Ross, Phys. Rev. B, 63, 132104 (2004). [3] A.B. Belonoshko, L. Burakovsky, S.P. Chen, B. Johansson, A.S. Mikhaylushkin, D.L. Preston, S.I. Simak, and D.C. Swift, Phys. Rev. Lett., 100, 135701 (2008). [4] C. Cazorla, D. Alfè, and M.J. Gillan, Phys. Rev. Lett. 101, 049601 (2008). [5] A.S. Mikhaylushkin, S.I. Simak ,L. Burakovsky, S.P. Chen, B. Johansson, D.L. Preston, D.C. Swift, and A.B. Belonoshko Phys. Rev. Lett., 101, 049602 (2008). [6] B. Wang, G. Zhang, and Y. Wang, J. Alloys Compd., 556, 116-120, (2013).

Transfer matrix approach to electron transport in monolayer MoS2/MoO x heterostructures

NASA Astrophysics Data System (ADS)

Li, Gen

2018-05-01

Oxygen plasma treatment can introduce oxidation into monolayer MoS2 to transfer MoS2 into MoO x , causing the formation of MoS2/MoO x heterostructures. We find the MoS2/MoO x heterostructures have the similar geometry compared with GaAs/Ga1‑x Al x As semiconductor superlattice. Thus, We employ the established transfer matrix method to analyse the electron transport in the MoS2/MoO x heterostructures with double-well and step-well geometries. We also considere the coupling between transverse and longitudinal kinetic energy because the electron effective mass changes spatially in the MoS2/MoO x heterostructures. We find the resonant peaks show red shift with the increasing of transverse momentum, which is similar to the previous work studying the transverse-momentum-dependent transmission in GaAs/Ga1‑x Al x As double-barrier structure. We find electric field can enhance the magnitude of peaks and intensify the coupling between longitudinal and transverse momentums. Moreover, higher bias is applied to optimize resonant tunnelling condition to show negative differential effect can be observed in the MoS2/MoO x system.

Low-budget policy tool to empower Israeli insureds to demand their rights in the healthcare system.

PubMed

Brammli-Greenberg, Shuli; Waitzberg, Ruth; Medina-Artom, Tamar; Adijes-Toren, Ariella

2014-12-01

Since 1995 universal healthcare coverage has been provided in Israel through National Health Insurance (NHI). Although the country has lower rates of health spending than most OECD countries, the NHI Law stipulates that a broad benefits package will be provided by four competing Health Plans (HPs). These third-party payers manage healthcare utilization and cost through mechanisms that affect both provider and consumer behavior. Cost Containment is one of their main organizational objectives. The Ministry of Health (MoH) supervises HPs to ensure that they provide their members with adequate healthcare of high quality in accordance with the NHI Law and uphold the principles of efficiency and equity. In this paper we report on a policy instrument recently introduced by the MoH which enables it to share some of its responsibility for supervision with the insureds. This policy instrument is a website launched in 2014 that gives access to transparent information about the coverage of the NHI and voluntary health insurance (VHI) benefits packages. The idea is to empower insureds with knowledge and awareness of their rights and eligibility to benefits, so they can demand them from the HPs and/or private insurers; if refused, they can refer the case to the supervisor (the MoH). This policy instrument addresses market failures related to information asymmetry and can potentially improve competition among the HPs and within the VHI market. Copyright © 2014 The Authors. Published by Elsevier Ireland Ltd.. All rights reserved.

A rapid, partial leach and organic separation for the sensitive determination of Ag, Bi, Cd, Cu, Mo, Pb, Sb, and Zn in surface geologic materials by flame atomic absorption

USGS Publications Warehouse

Viets, J.G.; Clark, J.R.; Campbell, W.L.

1984-01-01

A solution of dilute hydrochloric acid, ascorbic acid, and potassium iodide has been found to dissolve weakly bound metals in soils, stream sediments, and oxidized rocks. Silver, Bi, Cd, Cu, Mo, Pb, Sb, and Zn are selectively extracted from this solution by a mixture of Aliquat 336 (tricaprylyl methyl ammonium chloride) and MIBK (methyl isobutyl ketone). Because potentially interfering major and minor elements do not extract, the organic separation allows interference-free determinations of Ag and Cd to the 0.05 ppm level, Mo, Cu, and Zn to 0.5 ppm, and Bi, Pb, and Sb to 1 ppm in the sample using flame atomic absorption spectroscopy. The analytical absorbance values of the organic solution used in the proposed method are generally enhanced more than threefold as compared to aqueous solutions, due to more efficient atomization and burning characteristics. The leaching and extraction procedures are extremely rapid; as many as 100 samples may be analyzed per day, yielding 800 determinations, and the technique is adaptable to field use. The proposed method was compared to total digestion methods for geochemical reference samples as well as soils and stream sediments from mineralized and unmineralized areas. The partial leach showed better anomaly contrasts than did total digestions. Because the proposed method is very rapid and is sensitive to pathfinder elements for several types of ore deposits, it should be useful for reconnaissance surveys for concealed deposits. ?? 1984.

Monte Carlo simulations on atropisomerism of thienotriazolodiazepines applicable to slow transition phenomena using potential energy surfaces by ab initio molecular orbital calculations.

PubMed

Morikami, Kenji; Itezono, Yoshiko; Nishimoto, Masahiro; Ohta, Masateru

2014-01-01

Compounds with a medium-sized flexible ring often show atropisomerism that is caused by the high-energy barriers between long-lived conformers that can be isolated and often have different biological properties to each other. In this study, the frequency of the transition between the two stable conformers, aS and aR, of thienotriazolodiazepine compounds with flexible 7-membered rings was estimated computationally by Monte Carlo (MC) simulations and validated experimentally by NMR experiments. To estimate the energy barriers for transitions as precisely as possible, the potential energy (PE) surfaces used in the MC simulations were calculated by molecular orbital (MO) methods. To accomplish the MC simulations with the MO-based PE surfaces in a practical central processing unit (CPU) time, the MO-based PE of each conformer was pre-calculated and stored before the MC simulations, and then only referred to during the MC simulations. The activation energies for transitions calculated by the MC simulations agreed well with the experimental ΔG determined by the NMR experiments. The analysis of the transition trajectories of the MC simulations revealed that the transition occurred not only through the transition states, but also through many different transition paths. Our computational methods gave us quantitative estimates of atropisomerism of the thienotriazolodiazepine compounds in a practical period of time, and the method could be applicable for other slow-dynamics phenomena that cannot be investigated by other atomistic simulations.

Exploring the Molecular Growth of Two Gigantic Half‐Closed Polyoxometalate Clusters {Mo180} and {Mo130Ce6}

PubMed Central

Xuan, Weimin; Pow, Robert; Long, De‐Liang

2017-01-01

Abstract Understanding the process of the self‐assembly of gigantic polyoxometalates and their subsequent molecular growth, by the addition of capping moieties onto the oxo‐frameworks, is critical for the development of the designed assembly of complex high‐nuclearity cluster species, yet such processes remain far from being understood. Herein we describe the molecular growth from {Mo150} and {Mo120Ce6} to afford two half‐closed gigantic molybdenum blue clusters {Mo180} (1) and {Mo130Ce6} (2), respectively. Compound 1 features a hat‐shaped structure with the parent wheel‐shaped {Mo150} being capped by a {Mo30} unit on one side. Similarly, 2 exhibits an elliptical lanthanide‐doped wheel {Mo120Ce6} that is sealed by a {Mo10} unit on one side. Moreover, the observation of the parent uncapped {Mo150} and {Mo120Ce6} clusters as minor products during the synthesis of 1 and 2 strongly suggests that the molecular growth process can be initialized from {Mo150} and {Mo120Ce6} in solution, respectively. PMID:28508585

Polyethylenimine Interfacial Layers in Inverted Organic Photovoltaic Devices: Effects of Ethoxylation and Molecular Weight on Efficiency and Temporal Stability.

PubMed

Courtright, Brett A E; Jenekhe, Samson A

2015-12-02

We report a comparative study of polyethylenimine (PEI) and ethoxylated-polyethylenimine (PEIE) cathode buffer layers in high performance inverted organic photovoltaic devices. The work function of the indium-tin oxide (ITO)/zinc oxide (ZnO) cathode was reduced substantially (Δφ = 0.73-1.09 eV) as the molecular weight of PEI was varied from 800 g mol(-1) to 750 000 g mol(-1) compared with the observed much smaller reduction when using a PEIE thin film (Δφ = 0.56 eV). The reference inverted polymer solar cells based on the small band gap polymer PBDTT-FTTE (ITO/ZnO/PBDTT-FTTE:PC70BM/MoO3/Ag), without a cathode buffer layer, had an average power conversion efficiency (PCE) of 6.06 ± 0.22%. Incorporation of a PEIE cathode buffer layer in the same PBDTT-FTTE:PC70BM blend devices gave an enhanced performance with a PCE of 7.37 ± 0.53%. In contrast, an even greater photovoltaic efficiency with a PCE of 8.22 ± 0.10% was obtained in similar PBDTT-FTTE:PC70BM blend solar cells containing a PEI cathode buffer layer. The temporal stability of the inverted polymer solar cells was found to increase with increasing molecular weight of the cathode buffer layer. The results show that PEI is superior to PEIE as a cathode buffer layer in high performance organic photovoltaic devices and that the highest molecular weight PEI interlayer provides the highest temporal stability.

NO-sensing performance of vacancy defective monolayer MoS2 predicted by density function theory

NASA Astrophysics Data System (ADS)

Li, Feifei; Shi, Changmin

2018-03-01

Using density functional theory (DFT), we predict the NO-sensing performance of monolayer MoS2 (MoS2-MLs) with and without MoS3-vacancy/S-vacancy defects. Our theoretical results demonstrate that MoS3- and S-vacancy defective MoS2-MLs show stronger chemisorption and greater electron transfer effects than pure MoS2-MLs. The charge transfer analysis showed pure and defective MoS2-MLs all act as donors. Both MoS3-vacancy and S-vacancy defects induce dramatic changes of electronic properties of MoS2-MLs, which have direct relationship with gas sensing performance. In addition, S-vacancy defect leads to more electrons transfer to NO molecule than MoS3-vacancy defect. The H2O molecule urges more electrons transfer from MoS3- or S-vacancy defective MoS2-MLs to NO molecule. We believe that this calculation results will provide some information for future experiment.

Effect of molecular intercalation on the local structure of superconducting Nax(NH3)yMoSe2 system

NASA Astrophysics Data System (ADS)

Simonelli, L.; Paris, E.; Wakita, T.; Marini, C.; Terashima, K.; Miao, X.; Olszewski, W.; Ramanan, N.; Heinis, D.; Kubozono, Y.; Yokoya, T.; Saini, N. L.

2017-12-01

We have studied the local structure of layered Nax(NH3)yMoSe2 system by Mo K-edge extended X-ray absorption fine structure (EXAFS) measurements performed as a function of temperature. We find that molecular intercalation in MoSe2 largely affects the Mo-Se network while Mo-Mo seems to sustain small changes. The Einstein temperature (ΘE) of Mo-Mo distance hardly changes (∼264 K) indicating that bond strength of this distance remains unaffected by intercalation. On the other hand, Mo-Se distance suffers a softening, revealed by the decrease of ΘE from ∼364 K to ∼350 K. The results indicate that Na+ ion transported by NH3 molecules may enter between the two MoSe-layers resulting reduced Se-Se coupling. Therefore, increased hybridization between Se 4p and Mo 4d orbitals due to inter-layer disorder is the likely reason of metallicity in intercalated MoSe2 and superconductivity at low temperature.

Comparison of metal ion concentrations and implant survival after total hip arthroplasty with metal-on-metal versus metal-on-polyethylene articulations

PubMed Central

Dahlstrand, Henrik; Stark, André; Wick, Marius C; Anissian, Lucas; Hailer, Nils P; Weiss, Rüdiger J

2017-01-01

Background and purpose Large metal-on-metal (MoM) articulations are associated with metal wear and corrosion, leading to increased metal ion concentrations and unacceptable revision rates. There are few comparative studies of 28-mm MoM articulations with conventional metal-on-polyethylene (MoP) couplings. We present a long-term follow-up of a randomized controlled trial comparing MoM versus MoP 28-mm articulations, focused on metal ions and implant survival. Patients and methods 85 patients with a mean age of 65 years at surgery were randomized to a MoM (Metasul) or a MoP (Protasul) bearing. After 16 years, 38 patients had died and 4 had undergone revision surgery. 13 patients were unavailable for clinical follow-up, leaving 30 patients (n = 14 MoM and n = 16 MoP) for analysis of metal ion concentrations and clinical outcome. Results 15-year implant survival was similar in both groups (MoM 96% [95% CI 88–100] versus MoP 97% [95% CI 91–100]). The mean serum cobalt concentration was 4-fold higher in the MoM (1.5 μg/L) compared with the MoP cohort (0.4 μg/L, p < 0.001) and the mean chromium concentration was double in the MoM (2.2 μg/L) compared with the MoP cohort (1.0 μg/L, p = 0.05). Mean creatinine levels were similar in both groups (MoM 93 μmol/L versus MoP 92 μmol/L). Harris hip scores differed only marginally between the MoM and MoP cohorts. Interpretation This is the longest follow-up of a randomized trial on 28-mm MoM articulations, and although implant survival in the 2 groups was similar, metal ion concentrations remained elevated in the MoM cohort even in the long term. PMID:28699417

Redox-Mediated Stabilization in Zinc Molybdenum Nitrides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arca, Elisabetta; Lany, Stephan; Perkins, John D.

We report on the theoretical prediction and experimental realization of new ternary zinc molybdenum nitride compounds. We used theory to identify previously unknown ternary compounds in the Zn-Mo-N systems, Zn 3MoN 4 and ZnMoN 2, and to analyze their bonding environment. Experiments show that Zn-Mo-N alloys can form in broad composition range from Zn 3MoN 4 to ZnMoN 2 in the wurtzite-derived structure, accommodating very large off-stoichiometry. Interestingly, the measured wurtzite-derived structure of the alloys is metastable for the ZnMoN 2 stoichiometry, in contrast to the Zn 3MoN 4 stoichiometry, where ordered wurtzite is predicted to be the ground state.more » The formation of Zn 3MoN 4-ZnMoN 2 alloy with wurtzite-derived crystal structure is enabled by the concomitant ability of Mo to change oxidation state from +VI in Zn 3MoN 4 to +IV in ZnMoN 2, and the capability of Zn to contribute to the bonding states of both compounds, an effect that we define as 'redox-mediated stabilization.' The stabilization of Mo in both the +VI and +IV oxidation states is due to the intermediate electronegativity of Zn, which enables significant polar covalent bonding in both Zn 3MoN 4 and ZnMoN 2 compounds. The smooth change in the Mo oxidation state between Zn 3MoN 4 and ZnMoN 2 stoichiometries leads to a continuous change in optoelectronic properties - from resistive and semitransparent Zn 3MoN 4 to conductive and absorptive ZnMoN 2. The reported redox-mediated stabilization in zinc molybdenum nitrides suggests there might be many undiscovered ternary compounds with one metal having an intermediate electronegativity, enabling significant covalent bonding, and another metal capable of accommodating multiple oxidation states, enabling stoichiometric flexibility.« less

Redox-Mediated Stabilization in Zinc Molybdenum Nitrides

DOE PAGES

Arca, Elisabetta; Lany, Stephan; Perkins, John D.; ...

2018-03-01

We report on the theoretical prediction and experimental realization of new ternary zinc molybdenum nitride compounds. We used theory to identify previously unknown ternary compounds in the Zn-Mo-N systems, Zn 3MoN 4 and ZnMoN 2, and to analyze their bonding environment. Experiments show that Zn-Mo-N alloys can form in broad composition range from Zn 3MoN 4 to ZnMoN 2 in the wurtzite-derived structure, accommodating very large off-stoichiometry. Interestingly, the measured wurtzite-derived structure of the alloys is metastable for the ZnMoN 2 stoichiometry, in contrast to the Zn 3MoN 4 stoichiometry, where ordered wurtzite is predicted to be the ground state.more » The formation of Zn 3MoN 4-ZnMoN 2 alloy with wurtzite-derived crystal structure is enabled by the concomitant ability of Mo to change oxidation state from +VI in Zn 3MoN 4 to +IV in ZnMoN 2, and the capability of Zn to contribute to the bonding states of both compounds, an effect that we define as 'redox-mediated stabilization.' The stabilization of Mo in both the +VI and +IV oxidation states is due to the intermediate electronegativity of Zn, which enables significant polar covalent bonding in both Zn 3MoN 4 and ZnMoN 2 compounds. The smooth change in the Mo oxidation state between Zn 3MoN 4 and ZnMoN 2 stoichiometries leads to a continuous change in optoelectronic properties - from resistive and semitransparent Zn 3MoN 4 to conductive and absorptive ZnMoN 2. The reported redox-mediated stabilization in zinc molybdenum nitrides suggests there might be many undiscovered ternary compounds with one metal having an intermediate electronegativity, enabling significant covalent bonding, and another metal capable of accommodating multiple oxidation states, enabling stoichiometric flexibility.« less

99Mo Yield Using Large Sample Mass of MoO3 for Sustainable Production of 99Mo

NASA Astrophysics Data System (ADS)

Tsukada, Kazuaki; Nagai, Yasuki; Hashimoto, Kazuyuki; Kawabata, Masako; Minato, Futoshi; Saeki, Hideya; Motoishi, Shoji; Itoh, Masatoshi

2018-04-01

A neutron source from the C(d,n) reaction has the unique capability of producing medical radioisotopes such as 99Mo with a minimum level of radioactive waste. Precise data on the neutron flux are crucial to determine the best conditions for obtaining the maximum yield of 99Mo. The measured yield of 99Mo produced by the 100Mo(n,2n)99Mo reaction from a large sample mass of MoO3 agrees well with the numerical result estimated with the latest neutron data, which are a factor of two larger than the other existing data. This result establishes an important finding for the domestic production of 99Mo: approximately 50% of the demand for 99Mo in Japan could be met using a 100 g 100MoO3 sample mass with a single accelerator of 40 MeV, 2 mA deuteron beams.

Re-evaluation and extension of the scope of elements in US Geological Survey Standard Reference Water Samples

USGS Publications Warehouse

Peart, D.B.; Antweiler, Ronald C.; Taylor, Howard E.; Roth, D.A.; Brinton, T.I.

1998-01-01

More than 100 US Geological Survey (USGS) Standard Reference Water Samples (SRWSs) were analyzed for numerous trace constituents, including Al, As, B, Ba, Be, Bi, Br, Cd, Cr, Co, Cu, I, Fe, Pb, Li, Mn, Mo, Ni, Rb, Sb, Se, Sr, Te, Tl, U, V, Zn and major elements (Ca, Mg, Na, SiO2, SO4, Cl) by inductively coupled plasma mass spectrometry and inductively coupled plasma atomic emission spectrometry. In addition, 15 USGS SRWSs and National Institute of Standards and Technology (NIST) standard reference material (SRM) 1641b were analyzed for mercury using cold vapor atomic fluorescence spectrometry. Also USGS SRWS Hg-7 was analyzed using isotope dilution-inductively coupled plasma mass spectrometry. The results were compared with the reported certified values of the following standard reference materials: NIST SRM 1643a, 1643b, 1643c and 1643d and National Research Council of Canada Riverine Water Reference Materials for Trace Metals SLRS-1, SLRS-2 and SLRS-3. New concentration values for trace and major elements in the SRWSs, traceable to the certified standards, are reported. Additional concentration values are reported for elements that were neither previously published for the SRWSs nor traceable to the certified reference materials. Robust statistical procedures were used that were insensitive to outliers. These data can be used for quality assurance/quality control purposes in analytical laboratories.

Atom-atom interactions around the band edge of a photonic crystal waveguide

NASA Astrophysics Data System (ADS)

Hood, Jonathan D.; Goban, Akihisa; Asenjo-Garcia, Ana; Lu, Mingwu; Yu, Su-Peng; Chang, Darrick E.; Kimble, H. J.

2016-09-01

Tailoring the interactions between quantum emitters and single photons constitutes one of the cornerstones of quantum optics. Coupling a quantum emitter to the band edge of a photonic crystal waveguide (PCW) provides a unique platform for tuning these interactions. In particular, the cross-over from propagating fields E(x)∝e±ikxxE(x)∝e±ikxx outside the bandgap to localized fields E(x)∝e-κx|x|E(x)∝e-κx|x| within the bandgap should be accompanied by a transition from largely dissipative atom-atom interactions to a regime where dispersive atom-atom interactions are dominant. Here, we experimentally observe this transition by shifting the band edge frequency of the PCW relative to the D1D1 line of atomic cesium for N¯=3.0±0.5N¯=3.0±0.5 atoms trapped along the PCW. Our results are the initial demonstration of this paradigm for coherent atom-atom interactions with low dissipation into the guided mode.

Mo-Mo Quintuple Bond is Highly Reactive in H-H, C-H, and O-H σ-Bond Cleavages Because of the Polarized Electronic Structure in Transition State.

PubMed

Chen, Yue; Sakaki, Shigeyoshi

2017-04-03

The recently reported high reactivity of the Mo-Mo quintuple bond of Mo 2 (N ∧ N) 2 (1) {N ∧ N = μ-κ 2 -CH[N(2,6-iPr 2 C 6 H 3 )] 2 } in the H-H σ-bond cleavage was investigated. DFT calculations disclosed that the H-H σ-bond cleavage by 1 occurs with nearly no barrier to afford the cis-dihydride species followed by cis-trans isomerization to form the trans-dihydride product, which is consistent with the experimental result. The O-H and C-H bond cleavages by 1 were computationally predicted to occur with moderate (ΔG° ⧧ = 9.0 kcal/mol) and acceptable activation energies (ΔG° ⧧ = 22.5 kcal/mol), respectively, suggesting that the Mo-Mo quintuple bond can be applied to various σ-bond cleavages. In these σ-bond cleavage reactions, the charge-transfer (CT Mo→XH ) from the Mo-Mo quintuple bond to the X-H (X = H, C, or O) bond and that (CT XH→Mo ) from the X-H bond to the Mo-Mo bond play crucial roles. Though the HOMO (dδ-MO) of 1 is at lower energy and the LUMO + 2 (dδ*-MO) of 1 is at higher energy than those of RhCl(PMe 3 ) 2 (LUMO and LUMO + 1 of 1 are not frontier MO), the H-H σ-bond cleavage by 1 more easily occurs than that by the Rh complex. Hence, the frontier MO energies are not the reason for the high reactivity of 1. The high reactivity of 1 arises from the polarization of dδ-type MOs of the Mo-Mo quintuple bond in the transition state. Such a polarized electronic structure enhances the bonding overlap between the dδ-MO of the Mo-Mo bond and the σ*-antibonding MO of the X-H bond to facilitate the CT Mo→XH and reduce the exchange repulsion between the Mo-Mo bond and the X-H bond. This polarized electronic structure of the transition state is similar to that of a frustrated Lewis pair. The easy polarization of the dδ-type MOs is one of the advantages of the metal-metal multiple bond, because such polarization is impossible in the mononuclear metal complex.

[Central Patients Admission (CPA) unit--connecting inpatient and outpatient care].

PubMed

Fleck, Martin; Zeuner, Martin; Schölmerich, Jürgen

2009-12-15

Due to the novel reimbursement policies, hospitals face substantial conflicts regarding best patient care and optimal utilization of resources. In order to optimize patient treatment, a central patients admission (CPA) unit has been established. All patients electively referred to the hospital were primarily treated by a medical specialist at the CPA unit. According to an appropriateness evaluation protocol established with the medical service of the health insurances of Bavaria ("MDK-Bayern"), patients were treated as inpatients or outpatients. The impact of this novel admission procedure was assessed for a period of 30 months. Within 30 months following establishment of the CPA unit, 10% of the patients were treated as outpatients, whereas 90% of referred patients were admitted as inpatients. Nonetheless, numbers of inpatients increased by 20.7% after 24 months compared to 12 months following establishment of the CPA unit with a substantial increase of patients referred by external medical specialists. In addition, there were no cases of inappropriate admission. The CPA unit is an ideal instrument for treating patients cross-sectorally as well as more effectively and economically advocating reorganization. Establishment of a CPA unit leads to greater satisfaction among patients, referring physicians, and medical staff.

Holey Reduced Graphene Oxide Coupled with an Mo2 N-Mo2 C Heterojunction for Efficient Hydrogen Evolution.

PubMed

Yan, Haijing; Xie, Ying; Jiao, Yanqing; Wu, Aiping; Tian, Chungui; Zhang, Xiaomeng; Wang, Lei; Fu, Honggang

2018-01-01

An in situ catalytic etching strategy is developed to fabricate holey reduced graphene oxide along with simultaneous coupling with a small-sized Mo 2 N-Mo 2 C heterojunction (Mo 2 N-Mo 2 C/HGr). The method includes the first immobilization of H 3 PMo 12 O 40 (PMo 12 ) clusters on graphite oxide (GO), followed by calcination in air and NH 3 to form Mo 2 N-Mo 2 C/HGr. PMo 12 not only acts as the Mo heterojunction source, but also provides the Mo species that can in situ catalyze the decomposition of adjacent reduced GO to form HGr, while the released gas (CO) and introduced NH 3 simultaneously react with the Mo species to form an Mo 2 N-Mo 2 C heterojunction on HGr. The hybrid exhibits superior activity towards the hydrogen evolution reaction with low onset potentials of 11 mV (0.5 m H 2 SO 4 ) and 18 mV (1 m KOH) as well as remarkable stability. The activity in alkaline media is also superior to Pt/C at large current densities (>88 mA cm -2 ). The good activity of Mo 2 N-Mo 2 C/HGr is ascribed to its small size, the heterojunction of Mo 2 N-Mo 2 C, and the good charge/mass-transfer ability of HGr, as supported by a series of experiments and theoretical calculations. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Comparitive study of fluorescence lifetime quenching of rhodamine 6G by MoS2 and Au-MoS2

NASA Astrophysics Data System (ADS)

Shakya, Jyoti; Kasana, Parath; Mohanty, T.

2018-04-01

Time resolved fluorescence study of Rhodamine 6G (R6G) in the presence of Molybdenum disulfide (MoS2) nanosheets and gold doped MoS2 (Au-MoS2) have been carried out and discussed. We have analyzed the fluorescence decay curves of R6G and it is observed that Au-MoS2 is a better fluorescence lifetime quencher as compare to MoS2 nanosheets. Also, the energy transfer efficiency and energy transfer rate from R6G to MoS2 and Au-MoS2 has been calculated and found higher for Au-MoS2.

Coprocessing of plastics with coal and petroleum resid

DOE Office of Scientific and Technical Information (OSTI.GOV)

Joo, H.; Curtis, C.W.

1995-12-31

Waste plastics have become an increasing problem in the United States since land filling is no longer considered a feasible disposal method. Since plastics are petroleum-derived materials, coprocessing then with coal to produce transportation fuels is a feasible alternative. In this study, catalytic coprocessing reactions were performed using Blind Canyon bituminous coal, Manji petroleum resid, and waste plastics. Model polymers including polystyrene, low density polyethylene (LDPE) and polyethylene tereplithalare (PET) were selected because they represent a substantial portion of the waste plastics generated in the United States. Coprocessing reactions of coal, resid, and polymer as well as reactions of individualmore » components and combinations of two components were performed at 430{degrees}C for one hour with an initial H{sub 2} pressure of 8.5 MPa introduced at ambient temperature with presulfided NiMo/Al{sub 2}O{sub 3} as catalyst. Coprocessing all three materials resulted in a substantial improvement in the total conversion compared to the coal plus polymer reaction and slightly less conversion than the resid plus polymer combinations.« less

Superconducting fluctuations in molybdenum nitride thin films

NASA Astrophysics Data System (ADS)

Baskaran, R.; Thanikai Arasu, A. V.; Amaladass, E. P.; Vaidhyanathan, L. S.; Baisnab, D. K.

2018-02-01

MoN thin films have been deposited using reactive sputtering. The change in resistance near superconducting transition temperature at various magnetic fields has been analyzed based on superconducting fluctuations in the system. The Aslamazov and Larkin scaling theory has been utilized to analyze the conductance change. The results indicate that most of the measurements show two dimensional (2D) nature and exhibit scaling behavior at lower magnetic fields (<7T), while a cross over to three dimensional (3D) nature has been clearly observed in measurements at higher fields (>7T). We have also analyzed our data based on the model in which there is no explicit dependence of Tc. These analyses also substantiate a crossover from a 2D nature to a 3D at larger fields. Analysis using lowest Landau level scaling theory for a 2D system exhibit scaling behavior and substantiate our observations. The broadening at low resistance part has been explained based on thermally activated flux flow model and show universal behavior. The dependence of Uo on magnetic field indicates both single and collective vortex behavior.

The cluster compound In{sub 4}Ti{sub 1.5}Mo{sub 0.5}Mo{sub 14}O{sub 26} containing Mo{sub 14} clusters and the new mono- and bi-capped trioctahedral Mo{sub 15} and Mo{sub 16} clusters: Synthesis, crystal structure, and electrical and magnetic properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gall, Philippe; Guizouarn, Thierry; Gougeon, Patrick, E-mail: Patrick.Gougeon@univ-rennes1.fr

2015-07-15

Single crystals of the new quaternary compound In{sub 4}Ti{sub 1.5}Mo{sub 0.5}Mo{sub 14}O{sub 26} were obtained by solid state reaction. The crystal structure was determined by single-crystal X-ray diffraction. In{sub 4}Ti{sub 1.5}Mo{sub 0.5}Mo{sub 14}O{sub 26} crystallizes in the orthorhombic space group Pbca with unit-cell parameters a=9.4432(14) Å, b=11.4828(12) Å, c=20.299(4) Å and Z=4. Full-matrix least-squares refinement on F{sup 2} using 3807 independent reflections for 219 refinable parameters resulted in R{sub 1}=0.0259 and wR{sub 2}=0.0591. The crystal structure contains in addition to Mo{sub 14} clusters the first examples of mono- and bi-capped trioctahedral Mo{sub 14} i.e. Mo{sub 15} and Mo{sub 16} clusters.more » The oxygen framework derives from a stacking along the a direction of close-packed layers with sequence (…ABAC…). The Mo–Mo distances range between 2.6938(5) and 2.8420(6) Å and the Mo–O distances between 1.879(5) and 2.250(3) Å, as usually observed in molybdenum oxide clusters. The indium atoms form In{sub 4}{sup 6+} bent chains with In–In distances of 2.6682(5) and 2.6622(8) Å and the Ti atoms are in highly distorted octahedral sites of oxygen atoms with Ti–O distances ranging between 1.865(4) and 2.161(4) Å. Magnetic susceptibility measurements confirm the presence of Ti{sup 4+} cations and the absence of localized moments on the Mo network. Electrical resistivity measurements on a single crystal of In{sub 4}Ti{sub 1.5}Mo{sub 0.5}Mo{sub 14}O{sub 26} show a semimetallic behavior. - Graphical abstract: We present here the synthesis, the crystal structure, and the electrical and magnetic properties of the new compound In{sub 4}Ti{sub 1.5}Mo{sub 0.5}Mo{sub 14}O{sub 26} in which Mo{sub 14} clusters coexist statistically with mono- and bi-capped trioctahedral Mo{sub 14} that is Mo{sub 15} and Mo{sub 16} clusters. - Highlights: • Single crystals of In{sub 4}Ti{sub 1.5}Mo{sub 0.5}Mo{sub 14}O{sub 26} were obtained by solid state reaction. • The crystal structure contains Mo{sub 14}, Mo{sub 15} and Mo{sub 16} clusters. • The indium atoms form In{sub 4}{sup 6+} bent chains. • Poorly metallic behavior. • Absence of localized moments on the Mo network as well as on the Ti atoms.« less

Reactivity of Cyclopentadienyl Molybdenum Compounds towards Formic Acid: Structural Characterization of CpMo(PMe3)(CO)2H, CpMo(PMe3)2(CO)H, [CpMo(μ-O)(μ-O2CH)]2, and [Cp*Mo(μ-O)(μ-O2CH)]2.

PubMed

Neary, Michelle C; Parkin, Gerard

2017-02-06

The molecular structures of CpMo(PMe 3 )(CO) 2 H and CpMo(PMe 3 ) 2 (CO)H have been determined by X-ray diffraction, thereby revealing four-legged piano-stool structures in which the hydride ligand is trans to CO. However, in view of the different nature of the four basal ligands, the geometries of CpMo(PMe 3 )(CO) 2 H and CpMo(PMe 3 ) 2 (CO)H deviate from that of an idealized four-legged piano stool, such that the two ligands that are orthogonal to the trans H-Mo-CO moiety are displaced towards the hydride ligand. While Cp R Mo(PMe 3 ) 3-x (CO) x H (Cp R = Cp, Cp*; x = 1, 2, 3) are catalysts for the release of H 2 from formic acid, the carbonyl derivatives, Cp R Mo(CO) 3 H, are also observed to form dinuclear formate compounds, namely, [Cp R Mo(μ-O)(μ-O 2 CH)] 2 . The nature of the Mo···Mo interactions in [CpMo(μ-O)(μ-O 2 CH)] 2 and [Cp*Mo(μ-O)(μ-O 2 CH)] 2 have been addressed computationally. In this regard, the two highest occupied molecular orbitals of [CpMo(μ-O)(μ-O 2 CH)] 2 correspond to metal-based δ* (HOMO) and σ (HOMO-1) orbitals. The σ 2 δ* 2 configuration thus corresponds to a formal direct Mo-Mo bond order of zero. The preferential occupation of the δ* orbital rather than the δ orbital is a consequence of the interaction of the latter orbital with p orbitals of the bridging oxo ligands. In essence, lone-pair donation from oxygen increases the electron count so that the molybdenum centers can achieve an 18-electron configuration without the existence of a Mo-Mo bond, whereas a Mo═Mo double bond is required in the absence of lone-pair donation.

Mechanism of corrosion of Ni base superalloys by molten Na2MoO4 at elevated temperatures

NASA Technical Reports Server (NTRS)

Misra, A. K.; Stearns, C. A.

1983-01-01

The corrosion of nickel base superalloy, U-700, by molten Na2MoO4 was studied in the temperature range of 750 deg to 950 deg C. After an induction period, the rate of corrosion is linear and catastrophic corrosion is observed. It is shown that the induction period is associated with the attainment of a minimum MoO3 activity in the melt, which corresponds to the equilibrium MoO3 activity for the reaction, 2MoO3(l) + Mo = 3MoO2(s). A mechanism is proposed to describe the catastrophic nature of corrosion, which involves transport of Ni++ through the melt resulting in formulation of NiO at the melt gas interface and basic fluxing of Cr2O3. The effect of the amount of Na2MoO4 on the corrosion kinetics was also studied. It is found that evaporation and the thermodynamic calculations for the Na2MoO4 - MoO3 system the activity of MoO3 is reduced considerably when dissolved in Na2MoO4, which causes a sharp decrease in the rate of evaporation of MoO3 from a Na2MoO4 - MoO3 melt.

The modulation of Schottky barriers of metal-MoS2 contacts via BN-MoS2 heterostructures.

PubMed

Su, Jie; Feng, Liping; Zhang, Yan; Liu, Zhengtang

2016-06-22

Using first-principles calculations within density functional theory, we systematically studied the effect of BN-MoS2 heterostructure on the Schottky barriers of metal-MoS2 contacts. Two types of FETs are designed according to the area of the BN-MoS2 heterostructure. Results show that the vertical and lateral Schottky barriers in all the studied contacts, irrespective of the work function of the metal, are significantly reduced or even vanish when the BN-MoS2 heterostructure substitutes the monolayer MoS2. Only the n-type lateral Schottky barrier of Au/BN-MoS2 contact relates to the area of the BN-MoS2 heterostructure. Notably, the Pt-MoS2 contact with n-type character is transformed into a p-type contact upon substituting the monolayer MoS2 by a BN-MoS2 heterostructure. These changes of the contact natures are ascribed to the variation of Fermi level pinning, work function and charge distribution. Analysis demonstrates that the Fermi level pinning effects are significantly weakened for metal/BN-MoS2 contacts because no gap states dominated by MoS2 are formed, in contrast to those of metal-MoS2 contacts. Although additional BN layers reduce the interlayer interaction and the work function of the metal, the Schottky barriers of metal/BN-MoS2 contacts still do not obey the Schottky-Mott rule. Moreover, different from metal-MoS2 contacts, the charges transfer from electrodes to the monolayer MoS2, resulting in an increment of the work function of these metals in metal/BN-MoS2 contacts. These findings may prove to be instrumental in the future design of new MoS2-based FETs with ohmic contact or p-type character.

MoCAP proteins regulated by MoArk1-mediated phosphorylation coordinate endocytosis and actin dynamics to govern development and virulence of Magnaporthe oryzae

PubMed Central

Yang, Jun; Chen, Deng; Liu, Muxing; Zhang, Haifeng; Zheng, Xiaobo; Wang, Ping; Peng, Youliang; Zhang, Zhengguang

2017-01-01

Actin organization is a conserved cellular process that regulates the growth and development of eukaryotic cells. It also governs the virulence process of pathogenic fungi, such as the rice blast fungus Magnaporthe oryzae, with mechanisms not yet fully understood. In a previous study, we found that actin-regulating kinase MoArk1 displays conserved functions important in endocytosis and actin organization, and MoArk1 is required for maintaining the growth and full virulence of M. oryzae. To understand how MoArk1 might function, we identified capping protein homologs from M. oryzae (MoCAP) that interact with MoArk1 in vivo. MoCAP is heterodimer consisting of α and β subunits MoCapA and MoCapB. Single and double deletions of MoCAP subunits resulted in abnormal mycelial growth and conidia formation. The ΔMocap mutants also exhibited reduced appressorium penetration and invasive hyphal growth within host cells. Furthermore, the ΔMocap mutants exhibited delayed endocytosis and abnormal cytoskeleton assembly. Consistent with above findings, MoCAP proteins interacted with MoAct1, co-localized with actin during mycelial development, and participated in appressorial actin ring formation. Further analysis revealed that the S85 residue of MoCapA and the S285 residue of MoCapB were subject to phosphorylation by MoArk1 that negatively regulates MoCAP functions. Finally, the addition of exogenous phosphatidylinositol 4,5-bisphosphate (PIP2) failed to modulate actin ring formation in ΔMocap mutants, in contrast to the wild-type strain, suggesting that MoCAP may also mediate phospholipid signaling in the regulation of the actin organization. These results together demonstrate that MoCAP proteins whose functions are regulated by MoArk1 and PIP2 are important for endocytosis and actin dynamics that are directly linked to growth, conidiation and pathogenicity of M. oryzae. PMID:28542408

Phase stability of Keplerate-type polyoxomolybdates controlled by added cationic surfactant.

PubMed

Fan, Dawei; Hao, Jingcheng

2009-05-15

Phase stability of two nanometer-scale Keplerate-type polyoxomolybdates, (NH(4))(42)[Mo(VI)(72)Mo(V)(60)O(372)(CH(3)COO)(30)(H(2)O)(72)]300H(2)O10CH(3)COONH(4) ({Mo(132)}) and Mo(VI)(72)Fe(III)(30)O(252)L(102)ca. 180H(2)O with L=H(2)O/CH(3)COO(-)/Mo(2)O(n-)(8/9) ({Mo(72)Fe(30)}), can be easily achieved by controlling the concentration of a cationic surfactant, tetradecyltrimethylammonium bromide (TTABr), in aqueous solution. Precipitates and floccules were observed when the stoichiometric ratios of rTTA+/{Mo132} and rTTA+/{Mo72Fe30} were 40:1 and 90:1, respectively, which were determined by zeta potential measurements. The surface charge properties and structure morphologies of {Mo(132)} and {Mo(72)Fe(30)} induced by controlling cationic TTABr in aqueous solution were determined by zeta potential measurements and transmission electron microscopy (TEM) observations. {Mo(132)} and {Mo(72)Fe(30)} can self-assemble into supramolecular "Blackberry" structures and exist at compositions less than the stoichiometric ratios of rTTA+/{Mo132} and rTTA+/{Mo72Fe30} in aqueous solution. Above the 1:1 stoichiometric ratio of TTABr/{Mo(132)} or TTABr/{Mo(72)Fe(30)}, the precipitates and floccules dissolve. Dynamic laser light scattering (DLS) measurements clearly demonstrated that the R(h) values have essentially no angular dependence at excess amounts of TTABr, suggesting the presence of spherically symmetric aggregates of {Mo(132)} and {Mo(72)Fe(30)}. Bilayer-like structures in aqueous solution were also demonstrated by TEM images. The interesting phase transition observed in our model systems of {Mo(132)} and {Mo(72)Fe(30)} macroanions with high chemical stability, similar shape, and masses could provide models for the understanding of more complex polyelectrolyte solutions and self-assembled soft magnetic materials and in bioapplications for highly selective adsorbents of proteins with different molecular sizes and charges.

Preparation of single-crystal spherical γ-Mo2N by temperature-programmed reaction between β-MoO3 and NH3

NASA Astrophysics Data System (ADS)

Wang, Lu; Zhang, Guo-Hua; Chou, Kuo-Chih

2017-10-01

In the present wok, single-crystalline spherical γ-Mo2N powders was successfully prepared by the temperature-programmed reaction of single-crystal spherical β-MoO3 with NH3 in the temperature ranges of 1013-1073 K. Herein, the Mo source used was monoclinic system, β-MoO3, a metastable phase of MoO3. It is found that the characterizations of the as-prepared γ-Mo2N powders are strongly depended on the selection of the MoO3 precursor. In other words, the as-prepared γ-Mo2N powders inherited the shape, size and structure of the used β-MoO3 precursors upon reaction with NH3. In order to make a comparison, β-MoO3 was also reduced by the mixed gases of N2 and H2 with the flow rate ratio of 1:3 at the identical conditions. It was found that pure β-Mo2N polycrystalline can be obtained when the temperature was 1013 K; while further increasing the reaction temperature, metal Mo powder will be turned up.

Microwave effects on NiMoS and CoMoS single-sheet catalysts.

PubMed

Borges, I; Silva, Alexander M; Modesto-Costa, Lucas

2018-05-04

Single-sheet nanoclusters of MoS 2 , NiMoS or CoMoS are widely used in hydrodesulfurization (HDS) catalysis in the petroleum industry. In HDS reactions under microwave irradiation, experiments indirectly pointed out that for pristine MoS 2 reaction rates are accelerated because hot spots are generated on the catalyst bed. In this work, we investigated NiMoS and CoMoS isolated single-sheet substituted catalysts before and after thiophene adsorption focusing on quantifying the effect of microwave irradiation. For that purpose, density functional theory (DFT) molecular charge densities of each system were decomposed according to the distributed multipole analysis (DMA) of Stone. Site dipole values of each system were directly associated with a larger or smaller interaction with the microwave field according to a proposed general approach. We showed that microwave enhancement of HDS reaction rates can occur more efficiently in the CoMoS and NiMoS promoted clusters compared to pristine MoS 2 in the following order: CoMoS > NiMoS > MoS 2 . The atomic origin of the catalyst hot spots induced by microwaves was clearly established in the promoted clusters.

Generalized Poisson-Kac Processes: Basic Properties and Implications in Extended Thermodynamics and Transport

NASA Astrophysics Data System (ADS)

Giona, Massimiliano; Brasiello, Antonio; Crescitelli, Silvestro

2016-04-01

We introduce a new class of stochastic processes in Rn,{{{mathbb R}}^n}, referred to as generalized Poisson-Kac (GPK) processes, that generalizes the Poisson-Kac telegrapher's random motion in higher dimensions. These stochastic processes possess finite propagation velocity, almost everywhere smooth trajectories, and converge in the Kac limit to Brownian motion. GPK processes are defined by coupling the selection of a bounded velocity vector from a family of N distinct ones with a Markovian dynamics controlling probabilistically this selection. This model can be used as a probabilistic tool for a stochastically consistent formulation of extended thermodynamic theories far from equilibrium.

Phase transformations in the reaction cell of TiNi-based sintered systems

NASA Astrophysics Data System (ADS)

Artyukhova, Nadezhda; Anikeev, Sergey; Yasenchuk, Yuriy; Chekalkin, Timofey; Gunther, Victor; Kaftaranova, Maria; Kang, Ji-Hoon; Kim, Ji-Soon

2018-05-01

The present work addresses the structural-phase state changes of porous TiNi-based compounds fabricated by reaction sintering (RS) of Ti and Ni powders with Co, Mo, and no additives introduced. The study also emphasizes the features of a reaction cell (RC) during the transition from the solid- to liquid-phase sintering. Mechanisms of phase transformations occurring in the solid phase, involving the low-melting Ti2Ni phase within the RC, have been highlighted. Also, the intermediate Ti2Ni phase had a crucial role to provide both the required RS behavior and modified phase composition of RS samples, and besides, it is found to be responsible for the near-equiatomic TiNi saturation of the melt. Both cobalt and molybdenum additives are shown to cause additional structuring of the transition zone (TZ) at the Ti2Ni‑TiNi interface and broadening of this zone. The impact of Co and Mo on the Ti2Ni phase is evident through fissuring of this phase layer, which is referred to solidified stresses increased in the layer due to post-alloying defects in the structure.

Learning and remembering real-world events after medial temporal lobe damage.

PubMed

Dede, Adam J O; Frascino, Jennifer C; Wixted, John T; Squire, Larry R

2016-11-22

The hippocampus is important for autobiographical memory, but its role is unclear. In the study, patients with hippocampal damage and controls were taken on a 25-min walk on the University of California, San Diego, campus during which 11 planned events occurred. Memory was tested directly after the walk. In addition, a second group of controls took the same walk and were tested after 1 mo. Patients with hippocampal damage remembered fewer details than controls tested directly after the walk but remembered a similar number of details as controls tested after 1 mo. Notably, the details that were reported by patients had the characteristics of episodic recollection and included references to particular places and events. Patients exhibited no special difficulty remembering spatial details in comparison with nonspatial details. Last, whereas both control groups tended to recall the events of the walk in chronological order, the order in which patients recalled the events was unrelated to the order in which they occurred. The findings illuminate the role of the hippocampus in autobiographical memory and in the spatial and nonspatial aspects of episodic recollection.

Neutronics Conversion Analyses of the Laue-Langevin Institute (ILL) High Flux Reactor (RHF)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bergeron, A.; Dionne, B.; Calzavara, Y.

2014-09-30

The following report describes the neutronics results obtained with the MCNP model of the RHF U7Mo LEU reference design that has been established in 2010 during the feasibility analysis. This work constitutes a complete and detailed neutronics analysis of that LEU design using models that have been significantly improved since 2010 and the release of the feasibility report. When possible, the credibility of the neutronics model is tested by comparing the HEU model results with experimental data or other codes calculations results. The results obtained with the LEU model are systematically compared to the HEU model. The changes applied tomore » the neutronics model lead to better comparisons with experimental data or improved the calculation efficiency but do not challenge the conclusion of the feasibility analysis. If the U7Mo fuel is commercially available, not cost prohibitive, a back-end solution is established and if it is possible to manufacture the proposed element, neutronics analyses show that the performance of the reactor would not be challenged by the conversion to LEU fuel.« less

Solution-processed MoS(x) as an efficient anode buffer layer in organic solar cells.

PubMed

Li, Xiaodong; Zhang, Wenjun; Wu, Yulei; Min, Chao; Fang, Junfeng

2013-09-25

We reported a facile solution-processed method to fabricate a MoSx anode buffer layer through thermal decomposition of (NH4)2MoS4. Organic solar cells (OSCs) based on in situ growth MoSx as the anode buffer layer showed impressive improvements, and the power conversion efficiency was higher than that of conventional PEDOT:PSS-based device. The MoSx films obtained at different temperatures and the corresponding device performance were systematically studied. The results indicated that both MoS3 and MoS2 were beneficial to the device performance. MoS3 could result in higher Voc, while MoS2 could lead to higher Jsc. Our results proved that, apart from MoO3, molybdenum sulfides and Mo(4+) were also promising candidates for the anode buffer materials in OSCs.

Investigation on MoS2 and graphite coatings and their effects on the tribological properties of the radial spherical plain bearings

NASA Astrophysics Data System (ADS)

Qiu, Ming; Lu, Jianjun; Li, Yingchun; Lv, Guisen

2016-07-01

With constant enlargement of the application areas of the spherical plain bearings, higher quality lubrication of the bearings is required. To solve the lubricating problems of spherical plain bearings under high temperature, high vacuum, high speed, heavy loads and strong oxidation conditions, it is urgent for us to develop more excellent self-lubricating technologies. In this paper, the bonded solid lubricant coatings, which use inorganic phosphate as the binder, the mixture of MoS2 and graphite with two different weight proportions as the solid lubricant, are prepared by spraying under three different spray gun pressures. The bonding strength tests on the coatings show that the best spraying pressure is 0.2 MPa and the better mixing proportion of MoS2 to Graphite is 3:1. Then for the radial spherical plain bearings with steel/steel friction pair, after the coatings are made on the inner ring outer surfaces, the friction coefficient, the wear loss and the friction temperature of the bearings under four oscillating frequencies are investigated by a self-made tribo-tester. The test results, SEM of the worn morphologies and EDS of worn areas show that tribological properties of the bearing are obviously improved by the bonded solid lubricant coatings. When sprayed under the spray gun pressure of 0.2 MPa, the bearings have better anti-friction and anti-wear properties than those sprayed under 0.1 MPa and 0.3 MPa. Further as proved from the XPS analysis, between the coating with 3:1 mixing ratio of MoS2 to Graphite and the coating with 1:1 ratio, the former has less oxidation occurred on the surface and therefore has better tribological characteristics than the latter. This paper provides a reference to developing a new product of the radial spherical plain bearings with high bonding strength, oxidation resistance and abrasion resistance.

Evaluating the relationship between education level and cognitive impairment with the Montreal Cognitive Assessment Test.

PubMed

Yancar Demir, Esra; Özcan, Tuba

2015-09-01

Mild cognitive impairment (MCI) is defined as 'a cognitive decline greater than that expected for an individual's age and education level but that does not interfere notably with activities of daily life'. The Montreal Cognitive Assessment (MoCA) is a screening test for MCI. We investigated the performance of the Turkish version of the MoCA in detecting MCI among elderly persons in a rural area, the majority of whom have a low level of education. We evaluated 50 consecutive men referred from an outpatient clinic. Educational level was divided into three categories: group 1, less than primary (<5 years); group 2, primary (5 years); group 3, more than primary (>5 years). We evaluated the effect of education on MoCA scores and compared subjects' test performance among the different categories of education level. A total of 50 male patients with MCI (mean age: 70.74 ± 7.87) met the inclusion criteria. There were no differences in the total scores based on education or in the subscores for visuospatial/executive function, naming, attention, abstraction and delayed recall. Language was the only domain that showed significant differences between the groups. In post-hoc analysis, differences were found between groups 1 and 3 and between groups 1 and 2. Group 1 had significantly lower scores for language. The repeat subscore for language was significantly lower in group 1 than in group 2. In fluency, there were significant differences between groups 2 and 3 and between group 1 and 3. To our knowledge, this is the first study to analyze the applicability of the Turkish version of MoCA in populations with little education. Our results emphasize the need to adapt the language sections of this test, so it can be easily used in populations with low education levels. © 2014 The Authors. Psychogeriatrics © 2014 Japanese Psychogeriatric Society.

Determination of residual acetone and acetone related impurities in drug product intermediates prepared as Spray Dried Dispersions (SDD) using gas chromatography with headspace autosampling (GCHS).

PubMed

Quirk, Emma; Doggett, Adrian; Bretnall, Alison

2014-08-05

Spray Dried Dispersions (SDD) are uniform mixtures of a specific ratio of amorphous active pharmaceutical ingredient (API) and polymer prepared via a spray drying process. Volatile solvents are employed during spray drying to facilitate the formation of the SDD material. Following manufacture, analytical methodology is required to determine residual levels of the spray drying solvent and its associated impurities. Due to the high level of polymer in the SDD samples, direct liquid injection with Gas Chromatography (GC) is not a viable option for analysis. This work describes the development and validation of an analytical approach to determine residual levels of acetone and acetone related impurities, mesityl oxide (MO) and diacetone alcohol (DAA), in drug product intermediates prepared as SDDs using GC with headspace (HS) autosampling. The method development for these analytes presented a number of analytical challenges which had to be overcome before the levels of the volatiles of interest could be accurately quantified. GCHS could be used after two critical factors were implemented; (1) calculation and application of conversion factors to 'correct' for the reactions occurring between acetone, MO and DAA during generation of the headspace volume for analysis, and the addition of an equivalent amount of polymer into all reference solutions used for quantitation to ensure comparability between the headspace volumes generated for both samples and external standards. This work describes the method development and optimisation of the standard preparation, the headspace autosampler operating parameters and the chromatographic conditions, together with a summary of the validation of the methodology. The approach has been demonstrated to be robust and suitable to accurately determine levels of acetone, MO and DAA in SDD materials over the linear concentration range 0.008-0.4μL/mL, with minimum quantitation limits of 20ppm for acetone and MO, and 80ppm for DAA. Copyright © 2014 Elsevier B.V. All rights reserved.

Standard Gibbs energy of formation of Mo 3Te 4 by emf measurements

NASA Astrophysics Data System (ADS)

Mallika, C.; Sreedharan, O. M.

1990-03-01

The emf of the galvanic cells Pt, Mo, MoO 2¦8 YSZ¦'FeO', Fe, Pt (I) and Pt, Fe,'FeO' ¦8 YSZ¦MoO 2, Mo 3Te 4, MoTe 2(α), C, Pt (II) were measured over the temperature ranges 837 to 1151 K and 775 to 1196 K, respectively, using 8 mass% yttria-stabilized zirconia (8 YSZ) as the solid electrolyte. From the emf values, the partial molar Gibbs energy of solution of molybdenum in Mo 3Te 4/MoTe 2(α), Δ ḠMo was found to be Δ ḠMo ± 1.19 ( kJ/mol) = -025.08 + 0.00420T(K) . Using the literature data for the Gibbs energy of formation of MoTe 2(α). the expression ΔG° f( Mo3Te4, s) ± 5.97 (kj/mol) = -253.58 + 0.09214 T( K) was derived for the range 775 to 1196 K. A third-law analysis yielded a value of -209 ± 10 kJ/mol for ΔH° f.298o of Mo 3Te 4(s).

Soil organic matter regulates molybdenum storage and mobility in forests

USGS Publications Warehouse

Marks, Jade A; Perakis, Steven; King, Elizabeth K.; Pett-Ridge, Julie

2015-01-01

The trace element molybdenum (Mo) is essential to a suite of nitrogen (N) cycling processes in ecosystems, but there is limited information on its distribution within soils and relationship to plant and bedrock pools. We examined soil, bedrock, and plant Mo variation across 24 forests spanning wide soil pH gradients on both basaltic and sedimentary lithologies in the Oregon Coast Range. We found that the oxidizable organic fraction of surface mineral soil accounted for an average of 33 %of bulk soil Mo across all sites, followed by 1.4 % associated with reducible Fe, Al, and Mn-oxides, and 1.4 % in exchangeable ion form. Exchangeable Mo was greatest at low pH, and its positive correlation with soil carbon (C) suggests organic matter as the source of readily exchangeable Mo. Molybdenum accumulation integrated over soil profiles to 1 m depth (τMoNb) increased with soil C, indicating that soil organic matter regulates long-term Mo retention and loss from soil. Foliar Mo concentrations displayed no relationship with bulk soil Mo, and were not correlated with organic horizon Mo or soil extractable Mo, suggesting active plant regulation of Mo uptake and/or poor fidelity of extractable pools to bioavailability. We estimate from precipitation sampling that atmospheric deposition supplies, on average, over 10 times more Mo annually than does litterfall to soil. In contrast, bedrock lithology had negligible effects on foliar and soil Mo concentrations and on Mo distribution among soil fractions. We conclude that atmospheric inputs may be a significant source of Mo to forest ecosystems, and that strong Mo retention by soil organic matter limits ecosystem Mo loss via dissolution and leaching pathways.

Highly Enhanced Gas Adsorption Properties in Vertically Aligned MoS2 Layers.

PubMed

Cho, Soo-Yeon; Kim, Seon Joon; Lee, Youhan; Kim, Jong-Seon; Jung, Woo-Bin; Yoo, Hae-Wook; Kim, Jihan; Jung, Hee-Tae

2015-09-22

In this work, we demonstrate that gas adsorption is significantly higher in edge sites of vertically aligned MoS2 compared to that of the conventional basal plane exposed MoS2 films. To compare the effect of the alignment of MoS2 on the gas adsorption properties, we synthesized three distinct MoS2 films with different alignment directions ((1) horizontally aligned MoS2 (basal plane exposed), (2) mixture of horizontally aligned MoS2 and vertically aligned layers (basal and edge exposed), and (3) vertically aligned MoS2 (edge exposed)) by using rapid sulfurization method of CVD process. Vertically aligned MoS2 film shows about 5-fold enhanced sensitivity to NO2 gas molecules compared to horizontally aligned MoS2 film. Vertically aligned MoS2 has superior resistance variation compared to horizontally aligned MoS2 even with same surface area exposed to identical concentration of gas molecules. We found that electrical response to target gas molecules correlates directly with the density of the exposed edge sites of MoS2 due to high adsorption of gas molecules onto edge sites of vertically aligned MoS2. Density functional theory (DFT) calculations corroborate the experimental results as stronger NO2 binding energies are computed for multiple configurations near the edge sites of MoS2, which verifies that electrical response to target gas molecules (NO2) correlates directly with the density of the exposed edge sites of MoS2 due to high adsorption of gas molecules onto edge sites of vertically aligned MoS2. We believe that this observation extends to other 2D TMD materials as well as MoS2 and can be applied to significantly enhance the gas sensor performance in these materials.

Structures of Mo2Oy- and Mo2Oy (y=2, 3, and 4) studied by anion photoelectron spectroscopy and density functional theory calculations.

PubMed

Yoder, Bruce L; Maze, Joshua T; Raghavachari, Krishnan; Jarrold, Caroline Chick

2005-03-01

The competitive structural isomers of the Mo(2)O(y) (-)Mo(2)O(y) (y=2, 3, and 4) clusters are investigated using a combination of anion photoelectron (PE) spectroscopy and density functional theory calculations. The PE spectrum and calculations for MoO(3) (-)MoO(3) are also presented to show the level of agreement to be expected between the spectra and calculations. For MoO(3) (-) and MoO(3), the calculations predict symmetric C(3v) structures, an adiabatic electron affinity of 3.34 eV, which is above the observed value 3.17(2) eV. However, there is good agreement between observed and calculated vibrational frequencies and band profiles. The PE spectra of Mo(2)O(2) (-) and Mo(2)O(3) (-) are broad and congested, with partially resolved vibrational structure on the lowest energy bands observed in the spectra. The electron affinities (EA(a)s) of the corresponding clusters are 2.24(2) and 2.33(7) eV, respectively. Based on the calculations, the most stable structure of Mo(2)O(2) (-) is Y shaped, with the two Mo atoms directly bonded. Assignment of the Mo(2)O(3) (-) spectrum is less definitive, but a O-Mo-O-Mo-O structure is more consistent with overall electronic structure observed in the spectrum. The PE spectrum of Mo(2)O(4) (-) shows cleanly resolved vibrational structure and electronic bands, and the EA of the corresponding Mo(2)O(4) is determined to be 2.13(4) eV. The structure most consistent with the observed spectrum has two oxygen bridge bonds between the Mo atoms.

Excitatory and inhibitory innervation of the mouse orofacial motor nuclei: A stereological study.

PubMed

Faunes, Macarena; Oñate-Ponce, Alejandro; Fernández-Collemann, Sara; Henny, Pablo

2016-03-01

Neurons in the trigeminal (Mo5), facial (Mo7), ambiguus (Amb), and hypoglossal (Mo12) motor nuclei innervate jaw, facial, pharynx/larynx/esophagus, and tongue muscles, respectively. They are essential for movements subserving feeding, exploration of the environment, and social communication. These neurons are largely controlled by sensory afferents and premotor neurons of the reticular formation, where central pattern generator circuits controlling orofacial movements are located. To provide a description of the orofacial nuclei of the adult mouse and to ascertain the influence of excitatory and inhibitory afferents upon them, we used stereology to estimate the number of motoneurons as well as of varicosities immunopositive for glutamate (VGluT1+, VGluT2+) and GABA/glycine (known as VIAAT+ or VGAT+) vesicular transporters in the Mo5, Mo7, Amb, and Mo12. Mo5, Mo7, Amb, and Mo12 contain ∼1,000, ∼3,000, ∼600, and ∼1,700 cells, respectively. VGluT1+, VGluT2+, and VIAAT+ varicosities respectively represent: 28%, 41%, and 31% in Mo5; 2%, 49%, and 49% in Mo7; 12%, 42%, and 46% in Amb; and 4%, 54%, and 42% in Mo12. The Mo5 jaw-closing subdivision shows the highest VGluT1+ innervation. Noticeably, the VGluT2+ and VIAAT+ varicosity density in Mo7 is 5-fold higher than in Mo5 and 10-fold higher than in Amb and Mo12. The high density of terminals in Mo7 likely reflects the convergence and integration of numerous inputs to motoneurons subserving the wide range of complex behaviors to which this nucleus contributes. Also, somatic versus neuropil location of varicosities suggests that most of these afferents are integrated in the dendritic trees of Mo7 neurons. © 2015 Wiley Periodicals, Inc.

Is the 2000 CDC growth reference appropriate for developing countries?

PubMed

Roberfroid, Dominique; Lerude, Marie-Paule; Pérez-Cueto, Armando; Kolsteren, Patrick

2006-04-01

In 2000, the Centers for Disease Control and Prevention (CDC) produced a revised growth reference. This has already been used in different settings outside the USA. Using data obtained during a nutritional survey in Madagascar, we compare results produced by using both the 2000 CDC and the 1978 National Center for Health Statistics (NCHS)/World Health Organization (WHO) growth references. We show that changing the reference has an important impact on nutritional diagnosis. In particular, the prevalence of wasting is greatly increased. This could generate substantial operational and clinical difficulties. We recommend continued use of the 1978 NCHS/WHO reference until release of the new WHO multi-country growth charts.

MoMip11, a MoRgs7-interacting protein, functions as a scaffolding protein to regulate cAMP signaling and pathogenicity in the rice blast fungus Magnaporthe oryzae.

PubMed

Yin, Ziyi; Zhang, Xiaofang; Wang, Jingzhen; Yang, Lina; Feng, Wanzhen; Chen, Chen; Gao, Chuyun; Zhang, Haifeng; Zheng, Xiaobo; Wang, Ping; Zhang, Zhengguang

2018-05-04

The rice blast fungus Magnaporthe oryzae has eight regulators of G-protein signaling (RGS) and RGS-like proteins (MoRgs1 to MoRgs8) that exhibit both distinct and shared regulatory functions in the growth, differentiation and pathogenicity of the fungus. We found MoRgs7 with a unique RGS-seven transmembrane (7-TM) domain motif is localized to the highly dynamic tubule-vesicular compartments during early appressorium differentiation followed by gradually degradation. To explore whether this involves an active signal perception of MoRgs7, we identified a Gbeta-like/RACK1 protein homolog in M. oryzae MoMip11 that interacts with MoRgs7. Interestingly, MoMip11 selectively interacted with several components of the cAMP regulatory pathway, including Gα MoMagA and the high-affinity phosphodiesterase MoPdeH. We further showed that MoMip11 promotes MoMagA activation and suppresses MoPdeH activity thereby upregulating intracellular cAMP levels. Moreover, MoMip11 is required for the response to multiple stresses, a role also shared by Gbeta-like/RACK1 adaptor proteins. In summary, we revealed a unique mechanism by which MoMip11 links MoRgs7 and G-proteins to reugulate cAMP signaling, stress responses and pathogenicity of M. oryzae. Our studies revealed the multitude of regulatory networks that govern growth, development and pathogenicity in this important causal agent of rice blast. © 2018 Society for Applied Microbiology and John Wiley & Sons Ltd.

Promotional Effects of In on Non-Oxidative Methane Transformation Over Mo-ZSM-5

DOE PAGES

Zhang, Yang; Kidder, Michelle; Ruther, Rose E.; ...

2016-08-16

In this paper, we present a new class of catalysts, InMo-ZSM- 5, which can be prepared by indium impregnation of Mo-ZSM- 5. The incorporation of indium dramatically decreases coke formation during methane dehydroaromatization. The benzene and C 2 hydrocarbons selectivity among total hydrocarbons over InMo-ZSM- 5 remains comparable to that of Mo-ZSM- 5 despite reduced methane conversion due to decreased coke formation. We found 1 wt% indium to be optimal loading for reducing coke selectivity to half that of Mo-ZSM- 5. Characterization methods were not helpful in discerning the interaction of In with Mo but experiments with bimetallic 1In2Mo-ZSM- 5more » and mechanical mixture 1In+2Mo-ZSM- 5 suggest that In and Mo need to be in close proximity to suppress coke formation. Finally, this is supported by temperature programmed reduction experiments which show that In incorporation leads to lower Mo reduction temperature in In2Mo-ZMS- 5.« less

Determination of Mo- and Ca-isotope ratios in Ca100MoO4 crystal for AMoRE-I experiment

NASA Astrophysics Data System (ADS)

Karki, S.; Aryal, P.; Kim, H. J.; Kim, Y. D.; Park, H. K.

2018-01-01

The first phase of the AMoRE (Advanced Mo-based Rare process Experiment) is to search for neutrinoless double-beta decay of 100Mo with calcium molybdate (Ca100MoO4) crystals enriched in 100Mo and depleted in 48Ca using a cryogenic technique at Yangyang underground laboratory in Korea. It is important to know 100Mo- and 48Ca-isotope ratios in Ca100MoO4 crystal to estimate half-life of 100Mo decays and to 2 νββ background from 48Ca. We employed the ICP-MS (Inductive Coupled Plasma Mass Spectrometer) to measure 100Mo- and 48Ca-isotope ratios in Ca100MoO4 crystal. The measured results for 100Mo- and 48Ca-isotope ratios in the crystal are (94 . 6 ± 2 . 8) % and (0 . 00211 ± 0 . 00006) %, respectively, where errors are included both statistical and systematic uncertainties.

Oxidation resistant Mo-Mo2B-silica and Mo-Mo2B-silicate composites for high temperature applications

NASA Astrophysics Data System (ADS)

Cochran, J. K.; Daloz, W. L.; Marshall, P. E.

2011-12-01

Development of Mo composites based on the Mo-Si-B system has been demonstrated as a possible new route to achieving a high temperature Mobased material. In this new system, the silicide phases are replaced directly with silica or other silicate materials. These composites avoid the high ductile to brittle transition temperature observed for Mo-Si-B alloys by removing the Si that exists in solid solution in Mo at equilibrium with its silicides. A variety of compositions is tested for room temperature ductility and oxidation resistance. A system based upon Mo, Mo2B, and SrO·Al2O3·(SiO2)2 is shown to possess both ductility at 80 vol.% Mo and oxidation resistance at 60 vol.%. These composites can be produced using a powder processing approach and fired to greater than 95% theoretical density with a desirable microstructure of isolated boride and silicate phases within a ductile Mo matrix.

The effect of fetal gender on second-trimester maternal serum inhibin-A concentration.

PubMed

Lam, Y H; Tang, M H

2001-08-01

Second-trimester serum inhibin-A is increasingly used as a fourth marker in addition to the triple test to screen for Down syndrome. We investigated whether fetal gender had an effect on serum inhibin-A concentration. A retrospective analysis was done on 316 normal pregnancies and 48 Down syndrome pregnancies in which maternal serum inhibin-A assays were performed between 15 and 20 weeks of gestation and in which the fetal sex was known. The median inhibin-A MoM (95% CI) for normal pregnancies in the presence of a male fetus was 0.93 (range 0.88-1.03). This was significantly lower than that in the presence of a female fetus (median MoM=1.04). The gender difference was not observed in the Down syndrome pregnancies. The increased inhibin-A concentration would lead to a 2.3-fold higher false-positive rate in the presence of a female fetus (10.6% vs. 4.6%; p<0.05, Chi-square test). Because of the small number of cases studied, the results need to be substantiated by a larger series. If the gender effect is confirmed, adjustment for fetal sex may be necessary when inhibin-A is used as a screening marker. Copyright 2001 John Wiley & Sons, Ltd.

Mammalian metabolic rates in the hottest fish on earth.

PubMed

Wood, Chris M; Brix, Kevin V; De Boeck, Gudrun; Bergman, Harold L; Bianchini, Adalto; Bianchini, Lucas F; Maina, John N; Johannsson, Ora E; Kavembe, Geraldine D; Papah, Michael B; Letura, Kisipan M; Ojoo, Rodi O

2016-06-03

The Magadi tilapia, Alcolapia grahami, a small cichlid fish of Lake Magadi, Kenya lives in one of the most challenging aquatic environments on earth, characterized by very high alkalinity, unusual water chemistry, and extreme O2, ROS, and temperature regimes. In contrast to most fishes which live at temperatures substantially lower than the 36-40 °C of mammals and birds, an isolated population (South West Hot Springs, SWHS) of Magadi tilapia thrives in fast-flowing hotsprings with daytime highs of 43 °C and night-time lows of 32 °C. Another population (Fish Springs Lagoon, FSL) lives in a lagoon with fairly stable daily temperatures (33-36 °C). The upper critical temperatures (Ctmax) of both populations are very high; moreover the SWHS tilapia exhibit the highest Ctmax (45.6 °C) ever recorded for a fish. Routine rates of O2 consumption (MO2) measured on site, together with MO2 and swimming performance at 25, 32, and 39 °C in the laboratory, showed that the SWHS tilapia exhibited the greatest metabolic performance ever recorded in a fish. These rates were in the basal range of a small mammal of comparable size, and were all far higher than in the FSL fish. The SWHS tilapia represents a bellwether organism for global warming.

Dietary toxicity of soluble and insoluble molybdenum to northern bobwhite quail (Colinus virginianus).

PubMed

Stafford, Jennifer M; Lambert, Charles E; Zyskowski, Justin A; Engfehr, Cheryl L; Fletcher, Oscar J; Clark, Shanna L; Tiwary, Asheesh; Gulde, Cynthia M; Sample, Bradley E

2016-03-01

Limited data are available on the effects of molybdenum (Mo) on avian wildlife, which impairs evaluation of ecological exposure and risk. While Mo is an essential trace nutrient in birds, little is known of its toxicity to birds exposed to molybdenum disulfide (MoS2), the predominant form found in molybdenite ore. The chemical form and bioavailability of Mo is important in determining its toxicity. Avian toxicity tests typically involve a soluble form of Mo, such as sodium molybdate dihydrate (SMD, Na2MoO4·2H2O); however MoS2 is generally insoluble, with low bioaccessibility under most environmental conditions. The current study monitored survival and general health (body weight and food consumption) of 9-day old northern bobwhite exposed to soluble Mo (SMD) and ore-related Mo (MoS2) in their diet for 30 days. Toxicity and bioavailability (e.g. tissue distribution) of the two Mo forms were compared. Histopathology evaluations and serum, kidney, liver, and bone tissue sample analyses were conducted. Copper, a nutrient integrally associated with Mo toxicity, was also measured in the diet and tissue. No treatment-related mortality occurred and no treatment-related lesions were recorded for either Mo form. Tissue analyses detected increased Mo concentrations in serum, kidney, liver, and bone tissues following exposure to SMD, with decreasing concentrations following a post-exposure period. For the soluble form, a No-Observed-Adverse-Effect Concentration (NOAEC) of 1200 mg Mo as SMD/kg feed (134 mg SMD/kg body weight/day) was identified based on body weight and food consumption. No adverse effects were observed in birds exposed to MoS2 at the maximum dose of 5000 mg MoS2/kg feed (545 mg MoS2/kg body weight/day). These results show that effects associated with MoS2, the more environmentally prevalent and less bioavailable Mo form, are much less than those observed for SMD. These data should support more realistic representations of exposure and risks to avian receptors from environmental Mo.

Trace element reference values in tissues from inhabitants of the EU. XII. Development of BioReVa program for statistical treatment.

PubMed

Iversen, B S; Sabbioni, E; Fortaner, S; Pietra, R; Nicolotti, A

2003-01-20

Statistical data treatment is a key point in the assessment of trace element reference values being the conclusive stage of a comprehensive and organized evaluation process of metal concentration in human body fluids. The EURO TERVIHT project (Trace Elements Reference Values in Human Tissues) was started for evaluating, checking and suggesting harmonized procedures for the establishment of trace element reference intervals in body fluids and tissues. Unfortunately, different statistical approaches are being used in this research field making data comparison difficult and in some cases impossible. Although international organizations such as International Federation of Clinical Chemistry (IFCC) or International Union of Pure and Applied Chemistry (IUPAC) have issued recommended guidelines for reference values assessment, including the statistical data treatment, a unique format and a standardized data layout is still missing. The aim of the present study is to present a software (BioReVa) running under Microsoft Windows platform suitable for calculating the reference intervals of trace elements in body matrices. The main scope for creating an ease-of-use application was to control the data distribution, to establish the reference intervals according to the accepted recommendation, on the base of the simple statistic, to get a standard presentation of experimental data and to have an application to which further need could be integrated in future. BioReVa calculates the IFCC reference intervals as well as the coverage intervals recommended by IUPAC as a supplement to the IFCC intervals. Examples of reference values and reference intervals calculated with BioReVa software concern Pb and Se in blood; Cd, In and Cr in urine, Hg and Mo in hair of different general European populations. University of Michigan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Yang; Kidder, Michelle; Ruther, Rose E.

In this paper, we present a new class of catalysts, InMo-ZSM- 5, which can be prepared by indium impregnation of Mo-ZSM- 5. The incorporation of indium dramatically decreases coke formation during methane dehydroaromatization. The benzene and C 2 hydrocarbons selectivity among total hydrocarbons over InMo-ZSM- 5 remains comparable to that of Mo-ZSM- 5 despite reduced methane conversion due to decreased coke formation. We found 1 wt% indium to be optimal loading for reducing coke selectivity to half that of Mo-ZSM- 5. Characterization methods were not helpful in discerning the interaction of In with Mo but experiments with bimetallic 1In2Mo-ZSM- 5more » and mechanical mixture 1In+2Mo-ZSM- 5 suggest that In and Mo need to be in close proximity to suppress coke formation. Finally, this is supported by temperature programmed reduction experiments which show that In incorporation leads to lower Mo reduction temperature in In2Mo-ZMS- 5.« less

Mechanism of molybdenum removal from the sea and its concentration in black shales: EXAFS evidence

USGS Publications Warehouse

Helz, G.R.; Miller, C.V.; Charnock, J.M.; Mosselmans, J.F.W.; Pattrick, R.A.D.; Garner, C.D.; Vaughan, D.J.

1996-01-01

Molybdenum K-edge EXAFS (extended X-ray absorption fine structure) spectra yield new structural information about the chemical environment of Mo in high-Mo black shales and sediments. Two spectral types are found. The less common one, associated with Mo ores developed in shale in China, is that of a MoS2 phase, possibly X-ray amorphous jordisite. The other, associated with Cretaceous deep sea sediments and with other black shales, is characterized by short Mo-O distances (1.69-1.71 A??), by Mo-S distances of 2.30-2.38 A??, and in some cases by second shell Mo and Fe interactions, which suggests that some Mo resides in transition metal-rich phases. EXAFS spectra of synthetic amorphous materials, prepared by scavenging Mo from HS solutions with Fe(II), FeOOH, and humic acid, suggest that the second spectral type arises from Mo present chiefly in two forms. One is a compact, Mo-Fe-S "cubane" type compound with Mo-S distances of ???2.36 A?? and Mo-Fe distances of ???2.66 A??, while the other is probably an organic form containing some Mo-O double bonds (???1.69 A??). Laboratory products, that were prepared by scavenging dissolved Mo from sulfidic solutions with humic acid, yield spectra quite similar to the second spectral type observed in shales and sediments, including unexpected indications of Mo-Fe interactions. Molybdenum L-edge spectra indicate that the mean oxidation state in the sediments and shales lies between IV and VI. This work demonstrates the merit of EXAFS for obtaining structural information on natural materials containing X-ray amorphous components which defeat conventional mineralogical characterization. The implications of these findings regarding Mo scavenging from sulfidic natural waters are considered. We introduce the concept of a geochemical switch, in which HS- transforms the marine behavior of Mo from that of a conservative element to that of a particle reactive element. The action point of the HS- switch is calculated to be, aHS- = 10-3.6 - 10-4.3. When aHS- approaches the action point, Mo becomes reactive to particles containing transition metals (e.g., Fe). We conjecture that thiols, including humic-bound thiol groups, also switch Mo behavior. In contrast to previous ideas, our model for Mo scavenging deemphasizes the role of reduction from Mo(VI) to Mo(V) as the initial step in scavenging; instead, we emphasize the ease with which Mo forms covalent bonds to transition metals and organic molecules via S bridges.

Epithermal Neutron Activation Analysis of the Asian Herbal Plants

NASA Astrophysics Data System (ADS)

Baljinnyam, N.; Jugder, B.; Norov, N.; Frontasyeva, M. V.; Ostrovnaya, T. M.; Pavlov, S. S.

2011-06-01

Asian medicinal herbs Chrysanthemum (Spiraea aquilegifolia Pall.) and Red Sandalwood (Pterocarpus Santalinus) are widely used in folk and Ayurvedic medicine for healing and preventing some diseases. The modern medical science has proved that the Chrysanthemum (Spiraea aquilegifolia Pall.) possesses the following functions: reducing blood press, dispelling cancer cell, coronary artery's expanding and bacteriostating and Red Sandalwood (Pterocarpus Santalinus) is recommended against headache, toothache, skin diseases, vomiting and sometimes it is taken for treatment of diabetes. Species of Chrysanthemums were collected in the north-eastern and central Mongolia, and the Red Sandalwood powder was imported from India. Samples of Chrysanthemums (branches, flowers and leaves) (0.5 g) and red sandalwood powder (0.5 g) were subjected to the multi-element instrumental neutron activation analysis using epithermal neutrons (ENAA) at the IBR-2 reactor, Frank Laboratory of Neutron Physics (FLNP) JINR, Dubna. A total of 41 elements (Na, Mg, Al, Cl, K, Ca, Sc, V, Cr, Mn, Fe, Co, Ni, Zn, As, Se, Br, Rb, Sr, Zr, Mo, Cd, Cs, Ba, La, Hf, Ta, W, Sb, Au, Hg, Ce, Nd, Sm, Eu, Tb, Dy, Yb, Th, U, Lu) were determined. For the first time such a large group of elements was determined in the herbal plants used in Mongolia. The quality control of the analytical results was provided by using certified reference material Bowen Cabbage. The results obtained are compared to the "Reference plant» data (B. Markert, 1992) and interpreted in terms of excess of such elements as Se, Cr, Ca, Fe, Ni, Mo, and rare earth elements.

Rhenium and osmium isotopes in black shales and Ni-Mo-PGE-rich sulfide layers, Yukon Territory, Canada, and Hunan and Guizhou provinces, China

USGS Publications Warehouse

Horan, M.F.; Morgan, J.W.; Grauch, R.I.; Coveney, R.M.; Murowchick, J.B.; Hulbert, L.J.

1994-01-01

Rhenium and osmium abundances and osmium isotopic compositions were determined by negative thermal ionization mass spectrometry for samples of Devonian black shale and an associated Ni-enriched sulfide layer from the Yukon Territory, Canada. The same composition information was also obtained for samples of early Cambrian Ni-Mo-rich sulfide layers hosted in black shale in Guizhou and Hunan provinces, China. This study was undertaken to constrain the origin of the PGE enrichment in the sulfide layers. Samples of the Ni sulfide layer from the Yukon Territory are highly enriched in Re, Os, and other PGE, with distinctly higher Re/192Os but similar Pt/Re, compared to the black shale host. Re-Os isotopic data of the black shale and the sulfide layer are approximately isochronous, and the data plot close to reference isochrons which bracket the depositional age of the enclosing shales. Samples of the Chinese sulfide layers are also highly enriched in Re, Os, and the other PGE. Re/192Os are lower than in the Yukon sulfide layer. Re-Os isotopic data for the sulfide layers lie near a reference isochron with an age of 560 Ma, similar to the depositional age of the black shale host. The osmium isotopic data suggest that Re and PGE enrichment of the brecciated sulfide layers in both the Yukon Territory and in southern China may have occurred near the time of sediment deposition or during early diagenesis, during the middle to late Devonian and early Cambrian, respectively. ?? 1994.

X-ray absorption and Raman spectroscopy studies of molybdenum environments in borosilicate waste glasses

NASA Astrophysics Data System (ADS)

McKeown, David A.; Gan, Hao; Pegg, Ian L.

2017-05-01

Mo-containing high-level nuclear waste borosilicate glasses were investigated as part of an effort to improve Mo loading while avoiding yellow phase crystallization. Previous work showed that additions of vanadium decrease yellow phase formation and increases Mo solubility. X-ray absorption spectroscopy (XAS) and Raman spectroscopy were used to characterize Mo environments in HLW borosilicate glasses and to investigate possible structural relationships between Mo and V. Mo XAS spectra for the glasses indicate isolated tetrahedral Mo6+O4 with Mo-O distances near 1.75 Å. V XANES indicate tetrahedral V5+O4 as the dominant species. Raman spectra show composition dependent trends, where Mo-O symmetrical stretch mode frequencies (ν1) are sensitive to the mix of alkali and alkaline earth cations, decreasing by up to 10 cm-1 for glasses that change from Li+ to Na+ as the dominant network-modifying species. This indicates that MoO4 tetrahedra are isolated from the borosilicate network and are surrounded, at least partly, by Na+ and Li+. Secondary ν1 frequency effects, with changes up to 7 cm-1, were also observed with increasing V2O5 and MoO3 content. These secondary trends may indicate MoO4-MoO4 and MoO4-VO4 clustering, suggesting that V additions may stabilize Mo in the matrix with respect to yellow phase formation.

Keplerate cluster (Mo-132) mediated electrostatic assembly of nanoparticles.

PubMed

Gooch, Jonathan; Jalan, Abhishek A; Jones, Stephanie; Hine, Corey R; Alam, Rabeka; Garai, Somenath; Maye, Mathew M; Müller, Achim; Zubieta, Jon

2014-10-15

The electrostatic assembly between a series of differently charged Mo-132-type Keplerates present in the compounds (NH4)42[{(Mo(VI))Mo(VI)5O21(H2O)6}12 {Mo(V)2O4(CH3COO)}30].ca. {300 H2O+10 CH3COONH4} (Mo-132a), (NH4)72-n[{(H2O)81-n+(NH4)n} {(Mo(VI))Mo(VI)5O21(H2O)6}12 {Mo(V)2O4(SO4)}30].ca. 200 H2O (Mo-132b), and Na10(NH4)62[{(Mo(VI))Mo(VI)5O21(H2O)6}12 {Mo(V)2O4(HPO4)}30]. ca. {300H2O+2Na(+)+2NH4(+)+4H2PO4(-)} (Mo-132c) with cationic gold nanoparticles (AuNPs) was investigated for the first time. The rapid electrostatic assembly from nanoscopic entities to micron scale aggregates was observed upon precipitation, which closely matched the point of aggregate electroneutrality. Successful assembly was demonstrated using UV-vis, DLS, TEM, and zeta-potential analysis. Results indicate that the point at which precipitation occurs is related to charge balance or electroneutrality, and that counterions at both the Mo-132 and AuNP play a significant role in assembly. Copyright © 2014 Elsevier Inc. All rights reserved.

Molybdenum Cycling During Crust Formation and Destruction

NASA Astrophysics Data System (ADS)

Greaney, A. T.; Rudnick, R. L.

2016-12-01

Molybdenum geochemistry has become an important tool for tracking the redox state of the early atmosphere and oceans as well as the emergence and sustainability of Mo-cofactored enzymes. However, in order for Mo to be enriched in the oceans, it must first be weathered out of the crust. Sulfides that weather in the presence of atmospheric O2have historically been deemed the predominant crustal source of Mo. Here, we test this assumption by determining the mineralogical hosts of Mo in Archean, Proterozoic, and Phanerozoic upper crustal rocks, using LA-ICP-MS. We also investigate Mo behavior during igneous differentiation and continental crust formation. We find that molybdenite, MoS2, is a weatherable sulfide source of Mo, but common igneous sulfides are not because their Mo concentrations are too low. However, molybdenite is uncommon in the upper continental crust. By contrast, volcanic glass is much more abundant and is a significant weatherable source of Mo that readily breaks down to release oxidized, soluble Mo whether or not atmospheric O2is present. Other common crustal mineral hosts of Mo are Ti-bearing phases like titanite, ilmenite, magnetite, and rutile that are resistant to weathering. Significant Mo depletion (relative to Ce and Pr) is observed in nearly every granitic rock analyzed in our study, but is not observed in OIB or MORB (Jenner and O'Neill, 2012). There are two possible reasons for this: 1) Mo is removed from cooling plutons during fluid expulsion, or 2) Mo is fractionated during igneous differentiation. The first scenario is a likely explanation given the solubility of oxidized Mo. However, correlations between Mo/Ce and Nb/La in several plutonic suites suggest a fractionating phase like rutile may sequester Mo in the lower crust. Additionally, a correlation between Mo/Ce and inferred tectonic setting (enrichments observed in rift-related plutons) suggest an overall tectonic influence on the availability of Mo in the upper crust.

Mo isotope fractionation during hydrothermal evolution of porphyry Cu systems

NASA Astrophysics Data System (ADS)

Shafiei, Behnam; Shamanian, GholamHossein; Mathur, Ryan; Mirnejad, Hassan

2015-03-01

We present Mo isotope compositions of molybdenite types from three successive stages of ore deposition in several porphyry copper deposits of the Kerman region, Iran. The data provide new insights into controlling processes on Mo isotope fractionation during the hydrothermal evolution of porphyry systems. The Mo isotope compositions of 27 molybdenite samples show wide variations in δ97Mo ranging from -0.37 to +0.92 ‰. The data reveal that molybdenites in the early and transitional stages of mineralization (preferentially 2H polytypes; δ97Mo mean = 0.35 ‰) have higher δ97Mo values than late stage (mainly 3R polytypes; δ97Mo mean = 0.02 ‰) molybdenites. This trend suggests that fractionation of Mo isotopes occurred in high-temperature stages of mineralization and that hydrothermal systems generally evolve towards precipitation of molybdenite with lower δ97Mo values. Taking into account the genetic models proposed for porphyry Cu deposits along with the temperature-dependent fractionation of Mo isotope ratios, it is proposed that large variations of Mo isotopes in the early and the transitional stages of ore deposition could be controlled by the separation of the immiscible ore-forming fluid phases with different density, pH, and ƒO2 properties (i.e., brine and vapor). The fractionation of Mo isotopes during fluid boiling and Rayleigh distillation processes likely dominates the Mo isotope budget of the remaining ore-forming fluids for the late stage of mineralization. The lower δ97Mo values in the late stage of mineralization can be explained by depletion of the late ore-forming hydrothermal solutions in 97Mo, as these fluids have moved to considerable distance from the source. Finally, the relationship observed between MoS2 polytypes (2H and 3R) and their Mo isotopic compositions can be explained by the molecular vibration theory, in which heavier isotopes are preferentially partitioned into denser primary 2H MoS2 crystals.

Fe (hydro) oxide controls Mo isotope fractionation during the weathering of granite

NASA Astrophysics Data System (ADS)

Wang, Zhibing; Ma, Jinlong; Li, Jie; Wei, Gangjian; Zeng, Ti; Li, Lei; Zhang, Le; Deng, Wenfeng; Xie, Luhua; Liu, Zhifeng

2018-04-01

Understanding the fractionation mechanisms of Mo isotopes and seeking the main hosts of light δ98/95Mo during chemical weathering of continental rocks is a prerequisite for constraining heavy δ98/95Mo input into rivers. This study investigates the Mo concentrations and δ98/95Mo values of bulk samples, chemical extractions, and clay fractions of weathering products in a granite weathering profile in Guangdong province, South China, as well as in surrounding stream water. Results from bulk samples show that the τ MoTiO2 values systematically decrease from 59.1% to -77.0%, and δ98/95Mo values systematically increase from -1.46‰ to -0.17‰, upwards in the profile (from 30 to 0 m depth). Atmospheric input has a limited effect on δ98/95Mo variations in the weathering profile. Adsorption and desorption processes of Fe (hydro) oxide are the dominant factors controlling the variations in δ98/95Mo, with light Mo isotopes preferentially adsorbed by Fe (hydro) oxide, and released during desorption process, whereas the incongruent dissolution of primary minerals has little effect. Organic materials and the clay fraction are not the main hosts of light δ98/95Mo, as indicated by the results of chemical extractions, which show that a large proportion (41.5-86.2%) of total Mo with light δ98/95Mo (-1.57‰ to -0.59‰) is associated with Fe (hydro) oxide. Moreover, a significant positive correlation exists between Mo concentrations and δ98/95Mo in the Fe (hydro) oxide extractions from bulk samples. Finally, δ98/95Mo in stream water indicates the release of heavier δ98/95Mo into river water during the chemical weathering of granite rock. The results advance our understanding the mechanisms of Mo isotope fractionation during chemical weathering and its isotopic mass balance in Earth's surface system.

A novel copper(II) coordination at His186 in full-length murine prion protein

DOE Office of Scientific and Technical Information (OSTI.GOV)

Watanabe, Yasuko; Hiraoka, Wakako; Igarashi, Manabu

2010-04-09

To explore Cu(II) ion coordination by His{sup 186} in the C-terminal domain of full-length prion protein (moPrP), we utilized the magnetic dipolar interaction between a paramagnetic metal, Cu(II) ion, and a spin probe introduced in the neighborhood of the postulated binding site by the spin labeling technique (SDSL technique). Six moPrP mutants, moPrP(D143C), moPrP(Y148C), moPrP(E151C), moPrP(Y156C), moPrP(T189C), and moPrP(Y156C,H186A), were reacted with a methane thiosulfonate spin probe and a nitroxide residue (R1) was created in the binding site of each one. Line broadening of the ESR spectra was induced in the presence of Cu(II) ions in moPrP(Y148R1), moPrP(Y151R1), moPrP(Y156R1), andmore » moPrP(T189R1) but not moPrP(D143R1). This line broadening indicated the presence of electron-electron dipolar interaction between Cu(II) and the nitroxide spin probe, suggesting that each interspin distance was within 20 A. The interspin distance ranges between Cu(II) and the spin probes of moPrP(Y148R1), moPrP(Y151R1), moPrP(Y156R1), and moPrP(T189R1) were estimated to be 12.1 A, 18.1 A, 10.7 A, and 8.4 A, respectively. In moPrP(Y156R1,H186A), line broadening between Cu(II) and the spin probe was not observed. These results suggest that a novel Cu(II) binding site is involved in His186 in the Helix2 region of the C-terminal domain of moPrP{sup C}.« less