Salt-assistant combustion synthesis of nanocrystalline Nd{sub 2}(Zr{sub 1-x}Sn{sub x}){sub 2}O{sub 7} (0 {<=} x {<=} 1) solid solutions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tong Yuping, E-mail: huabeitong@yahoo.cn; Wang Yanping

2009-11-15

Nanocrystalline Nd{sub 2}(Zr{sub 1-x}Sn{sub x}){sub 2}O{sub 7} series solid solutions were prepared by a convenient salt-assisted combustion process using glycine as fuel. The samples were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, Raman spectroscopy, transmission electron microscopy and high-resolution transmission electron microscopy. The results showed the Zr ion can be partially replaced by Sn ion. The partial substituted products were still single-phase solid solutions and the crystal form remained unchanged. TEM images reveal that the products are composed of well-dispersed square-shaped nanocrystals. The method provides a convenient and low-cost route for the synthesis of nanostructures of oxide materials.

Atomistic simulation of mineral-melt trace-element partitioning

NASA Astrophysics Data System (ADS)

Allan, Neil L.; Du, Zhimei; Lavrentiev, Mikhail Yu.; Blundy, Jon D.; Purton, John A.; van Westrenen, Wim

2003-09-01

We discuss recent advances in computational approaches to trace-element incorporation in minerals and melts. It is crucial to take explicit account of the local structural environment of each ion in the solid and the change in this environment following the introduction of a foreign atom or atoms. Particular attention is paid to models using relaxation (strain) energies and solution energies, and the use of these different models for isovalent and heterovalent substitution in diopside and forsterite. Solution energies are also evaluated for pyrope and grossular garnets, and pyrope-grossular solid solutions. Unfavourable interactions between dodecahedral sites containing ions of the same size and connected by an intervening tetrahedron lead to larger solubilities of trace elements in the garnet solid solution than in either end member compound and to the failure of Goldschmidt's first rule. Our final two examples are the partitioning behaviour of noble gases, which behave as 'ions of zero charge' and the direct calculation of high-temperature partition coefficients between CaO solid and melt via Monte Carlo simulations.

A solid solution series of atacamite type Ni{sub 2x}Mg{sub 2−2x}Cl(OH){sub 3}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bette, Sebastian; Dinnebier, Robert E.; Röder, Christian

2015-08-15

For the first time a complete solid solution series Ni{sub 2x}Mg{sub 2−2x}Cl(OH){sub 3} of an atacamite type alkaline main group metal chloride, Mg{sub 2}Cl(OH){sub 3}, and a transition group metal chloride, Ni{sub 2}Cl(OH){sub 3}, was prepared and characterized by chemical and thermal analysis as well as by Raman and IR spectroscopy, and high resolution laboratory X-ray powder diffraction. All members of the solid solution series crystallize in space group Pnam (62). The main building units of these crystal structures are distorted, edge-linked Ni/MgO{sub 4}Cl{sub 2} and Ni/MgO{sub 5}Cl octahedra. The distribution of Ni{sup 2+}- and Mg{sup 2+}-ions among these twomore » metal-sites within the solid solution series is discussed in detail. The crystallization of the solid solution phases occurs via an intermediate solid solution series, (Ni/Mg)Cl{sub 2x}(OH){sub 2−2x}, with variable Cl: OH ratio up to the 1:3 ratio according to the formula Ni{sub 2x}Mg{sub 2−2x} Cl(OH){sub 3}. For one isolated intermediate solid solution member, Ni{sub 0.70}Mg{sub 0.30}Cl{sub 0.58}(OH){sub 1.42}, the formation and crystal structure is presented as well. - Graphical abstract: For the first time a complete solid solution series, Ni{sub 2x}Mg{sub 2−2x} Cl(OH){sub 3}, was synthesized and characterized. Structure solution by revealed that Ni{sup 2+} prefers to occupy the Jahn–Teller-like distorted hole, out of two available cation sites. Substitution of Ni{sup 2+} by Mg{sup 2+} in atacamite type Ni{sub 2}Cl(OH){sub 3} results in systematic band shifts in Raman and IR spectra as well as in systematic changes in thermal properties. The α-polymorphs M{sub 2}Cl(OH){sub 3} with M=Mg{sup 2+}, Ni{sup 2+} and other divalent transition metal ions, as described in literature, were identified as separate compounds. - Highlights: • First synthesis of solid solution series between main and transition metal chloride. • Ni{sup 2+} prefers to occupy Jahn–Teller-like distorted octahedral holes. • Substitution of Ni{sup 2+} by Mg{sup 2+} results in systematic Raman and IR band shifts. • α-Polymorphs M{sub 2}Cl(OH){sub 3} with M=Mg{sup 2+}, Ni{sup 2+}, … as described in literature do not exist.« less

Phase equilibria and crystal chemistry of the CaO-1/2 >Nd2O3-CoOz system at 885 °C in air

NASA Astrophysics Data System (ADS)

Wong-Ng, W.; Laws, W.; Talley, K. R.; Huang, Q.; Yan, Y.; Martin, J.; Kaduk, J. A.

2014-07-01

The phase diagram of the CaO-1/2 >Nd2O3-CoOz system at 885 °C in air has been determined. The system consists of two calcium cobaltate compounds that have promising thermoelectric properties, namely, the 2D thermoelectric oxide solid solution, (Ca3-xNdx)Co4O9-z (0≤x≤0.5), which has a misfit layered structure, and Ca3Co2O6 which consists of 1D chains of alternating CoO6 trigonal prisms and CoO6 octahedra. Ca3Co2O6 was found to be a point compound without the substitution of Nd on the Ca site. The reported Nd2CoO4 phase was not observed at 885 °C. A ternary (Ca1-xNd1+x)CoO4-z (x=0) phase, or (CaNdCo)O4-z, was found to be stable at this temperature. A solid solution region of distorted perovskite (Nd1-xCax)CoO3-z (0≤x≤0.25, space group Pnma) was established. In the peripheral binary systems, while a solid solution region was identified for (Nd1-xCax)2O3-z (0≤x≤0.2), Nd was not found to substitute in the Ca site of CaO. Six solid solution tie-line regions and six three-phase regions were determined in the CaO-Nd2O3-CoOz system in air.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brgoch, Jakoah; Klob, Simon D.; Denault, Kristin A.

The preparation of Eu 2+-substituted barium aluminum silicates is achieved using a rapid microwave-assisted preparation. The phase evolution of two BaAl 2Si 2O 8:Eu 2+ polymorphs, the higher temperature hexagonal phase (hexacelsian), and the lower temperature monoclinic phase (celsian), is explored by varying the ramp time and soak time. This preparation method significantly reduces the reaction time needed to form these phases compared to conventional solid state routes. The luminescent properties of the two phases are identified under UV excitation with the hexagonal phase emitting in the UV region (λ em = 372 nm) and the monoclinic phase emitting inmore » the blue region (λ em = 438 nm). The differences in optical properties of the two polymorphs are correlated to the coordination number and arrangement of the alkali earth site. The optical properties of the monoclinic phase can be further tuned through the substitution of Sr 2+, forming the solid solution (Ba 1–xSr x)Al 2Si 2O 8:Eu 2+. Changes in the crystal structure due to Sr 2+ substitution produce a surprising blue-shift in the emission spectrum, which is explained by a greater dispersion of bond lengths in the (Ba/Sr)–O polyhedra. The entire monoclinic solid solution exhibits excellent quantum yields of nearly 90 %, owing to the structural rigidity provided by the highly connected tetrahedral network.« less

On the substitution of Sr ions at Y sites in YB(suba2)Cu3O(sub7-d)

NASA Astrophysics Data System (ADS)

Siddiqi, S. A.; Sreedhar, K.; Drobac, D.; Infante, C.; Matacotta, F. C.; Ganguly, P.

1989-10-01

The effect of Sr substitution at the Ba sites in YBa2 Cu3 O sub 7-d has been studied; attempts to substitute Sr exclusively at Y sites have not been successful. We have been able to substitute Sr at Y sites only when the Ba ions are simultaneously substituted by Sr to give solid solutions of the type Y sub 1-x Sr sub x Ba sub 2-2x Sr sub 2x Cu3 O(sub 7-)x(sub /2-d). These examples show superconducting transitions higher than 78 K without significant deterioration in the magnitude of the ac susceptibility. The substitutions are best understood in terms of site constraints on the ions occupying the Y and Ba sites.

Water Transport in Bicontinuous, Phase-Separated Membranes Made from Reactive Block Copolymers

DTIC Science & Technology

2014-12-01

polyurethane foam impregnated with activated carbon, a design that allows perspiration to evaporate while chemical agents are adsorbed onto the activated... dispersed into a minimal volume (4–5 drops) of ethanol. The catalyst solution was then added to the polymer solution while stirring rapidly. The solution...substituted styrene monomer; one interior block with units of other styrene monomers which have been sulfonated; non- dispersible and solid in water

Electronic structures of anatase (TiO2)1-x(TaON)x solid solutions: a first-principles study.

PubMed

Dang, Wenqiang; Chen, Hungru; Umezawa, Naoto; Zhang, Junying

2015-07-21

Sensitizing wide band gap photo-functional materials under visible-light irradiation is an important task for efficient solar energy conversion. Although nitrogen doping into anatase TiO2 has been extensively studied for this purpose, it is hard to increase the nitrogen content in anatase TiO2 because of the aliovalent nitrogen substituted for oxygen, leading to the formation of secondary phases or defects that hamper the migration of photoexcited charge carriers. In this paper, electronic structures of (TiO2)1-x(TaON)x (0 ≤ x ≤ 1) solid solutions, in which the stoichiometry is satisfied with the co-substitution of Ti for Ta along with O for N, are investigated within the anatase crystal structure using first-principles calculations. Our computational results show that the solid solutions have substantially narrower band gaps than TiO2, without introducing any localized energy states in the forbidden gap. In addition, in comparison with the pristine TiO2, the solid solution has a direct band gap when the content of TaON exceeds 0.25, which is advantageous to light absorption. The valence band maximum (VBM) of the solid solutions, which is mainly composed of N 2p states hybridized with O 2p, Ti 3d or Ta 5d orbitals, is higher in energy than that of pristine anatase TiO2 consisting of non-bonding O 2p states. On the other hand, incorporating TaON into TiO2 causes the formation of d-d bonding states through π interactions and substantially lowers the conduction band minimum (CBM) because of the shortened distance between some metal atoms. As a result, the anatase (TiO2)1-x(TaON)x is expected to become a promising visible-light absorber. In addition, some atomic configurations are found to possess exceptionally narrow band gaps.

Measurement of phenols dearomatization via electrolysis: the UV-Vis solid phase extraction method.

PubMed

Vargas, Ronald; Borrás, Carlos; Mostany, Jorge; Scharifker, Benjamin R

2010-02-01

Dearomatization levels during electrochemical oxidation of p-methoxyphenol (PMP) and p-nitrophenol (PNP) have been determined through UV-Vis spectroscopy using solid phase extraction (UV-Vis/SPE). The results show that the method is satisfactory to determine the ratio between aromatic compounds and aliphatic acids and reaction kinetics parameters during treatment of wastewater, in agreement with results obtained from numerical deconvolution of UV-Vis spectra. Analysis of solutions obtained from electrolysis of substituted phenols on antimony-doped tin oxide (SnO(2)--Sb) showed that an electron acceptor substituting group favored the aromatic ring opening reaction, preventing formation of intermediate quinone during oxidation. (c) 2009 Elsevier Ltd. All rights reserved.

Dissolution kinetics of iron-, manganese-, and copper-containing synthetic hydroxyapatites

NASA Technical Reports Server (NTRS)

Sutter, B.; Hossner, L. R.; Ming, D. W.

2005-01-01

Micronutrient-substituted synthetic hydroxyapatite (SHA) is being evaluated by the National Aeronautics and Space Administration's (NASA) Advanced Life Support (ALS) Program for crop production on long-duration human missions to the International Space Station or for future Lunar or Martian outposts. The stirred-flow technique was utilized to characterize Ca, P, Fe, Mn, and Cu release characteristics from Fe-, Mn-, and Cu-containing SHA in deionized (DI) water, citric acid, and diethylene-triamine-pentaacetic acid (DTPA). Initially, Ca and P release rates decreased rapidly with time and were controlled by a non-SHA calcium phosphate phase(s) with low Ca/P solution molar ratios (0.91-1.51) relative to solid SHA ratios (1.56-1.64). At later times, Ca/P solution molar ratios (1.47-1.79) were near solid SHA ratios and release rates decreased slowly indicating that SHA controlled Ca and P release. Substituted SHA materials had faster dissolution rates relative to unsubstituted SHA. The initial metal release rate order was Mn >> Cu > Fe which followed metal-oxide/phosphate solubility suggesting that poorly crystalline metal-oxides/phosphates were dominating metal release. Similar metal release rates for all substituted SHA (approximately 0.01 cmol kg-1 min-1) at the end of the DTPA experiment indicated that SHA dissolution was supplying the metals into solution and that poorly crystalline metal-oxide/phosphates were not controlling metal release. Results indicate that non-SHA Ca-phosphate phases and poorly crystalline metal-oxide/phosphates will contribute Ca, P, and metals. After these phases have dissolved, substituted SHA will be the source of Ca, P, and metals for plants.

Transport properties of dilute α -Fe (X ) solid solutions (X = C, N, O)

NASA Astrophysics Data System (ADS)

Schuler, Thomas; Nastar, Maylise

2016-06-01

We extend the self-consistent mean field (SCMF) method to the calculation of the Onsager matrix of Fe-based interstitial solid solutions. Both interstitial jumps and substitutional atom-vacancy exchanges are accounted for. A general procedure is introduced to split the Onsager matrix of a dilute solid solution into intrinsic cluster Onsager matrices, and extract from them flux-coupling ratios, mobilities, and association-dissociation rates for each cluster. The formalism is applied to vacancy-interstitial solute pairs in α -Fe (V X pairs, X = C, N, O), with ab initio based thermodynamic and kinetic parameters. Convergence of the cluster mobility contribution gives a controlled estimation of the cluster definition distance, taking into account both its thermodynamic and kinetic properties. Then, the flux-coupling behavior of each V X pair is discussed, and qualitative understanding is achieved from the comparison between various contributions to the Onsager matrix. Also, the effect of low-activation energy second-nearest-neighbor interstitial solute jumps around a vacancy on these results is addressed.

Comparative acid-base properties of the surface of components of the CdTe-ZnS system in series of substitutional solid solutions and their analogs

NASA Astrophysics Data System (ADS)

Kirovskaya, I. A.; Kasatova, I. Yu.

2011-07-01

The acid-base properties of the surface of solid solutions and binary components of the CdTe-ZnS system are studied by hydrolytic adsorption, nonaqueous conductometric titration, mechanochemistry, IR spectroscopy, and Raman scattering spectroscopy. The strength, nature, and concentration of acid centers on the original surface and that exposed to CO are determined. The changes in acid-base properties in dependence on the composition of the system under investigation in the series of CdB6, ZnB6 analogs are studied.

Synthesis and structure elucidation of fluoro substituted guanidines as potential therapeutic agents

NASA Astrophysics Data System (ADS)

Ullah, Waseem; Imtiaz-ud-Din; Raheel, Ahmad; Badshah, Amin; Tahir, Muhammad Nawaz

2017-09-01

Six new fluoro -substituted guanidines (1-6) were synthesized and characterized by 1H and 13C NMR spectroscopy to ascertain the structures in solution (DMSO) besides the solid state information collected through FT IR and single crystal X-ray spectroscopy. The XRD data for (1-3) show that molecules are stabilized by strong intramolecular hydrogen bonding. The compounds were also preliminary bio-assayed for anti-microbial studies and show good to moderate activities. The anti-oxidant data revealed that o and p-substituted fluoro-guanidines enhances their DPPH scavenging ability significantly.

Atomistic modeling of the solid-state chemistry of actinide materials

NASA Astrophysics Data System (ADS)

Shuller, Lindsay C.

Materials that incorporate actinides are critical to the nuclear fuel cycle, either as nuclear fuels or nuclear waste forms. In this thesis, I examine four materials: i) ThO2-UO2 solid solutions, ii) binary ThO2-CeO2-ZrO2 solid solutions, iii) Np-doped studtite, iv) Np-doped boltwoodite. Computational methods, particularly density functional theory (DFT) calculations and Monte-Carlo (MC) simulations, are used to determine the energetics and structures of these actinide-bearing materials. The solid-solution behavior of nuclear fuels and nuclear waste forms indicate the thermodynamic stability of the material, which is important for understanding the in-reactor fuel properties and long-term stability of used fuel. The ThxU1-xO2 and ThxCe 1-xO2 binaries are almost completely miscible; however, DeltaGmix reveals a small tendency for the systems to exsolve (e.g., DeltaEexsoln(Th xU1-xO2) = 0.13 kJ/(mol cations) at 750 K). Kinetic hindrances (e.g., interfacial energy) may inhibit exsolution, especially at the low temperatures necessary to stabilize the nanoscale exsolution lamellae observed in the ThxU1-xO2 and Ce xZr1-xO2 binaries. Miscibility in the Zr-bearing binaries is limited. At 1400 °C, only 3.6 and 0.09 mol% ZrO2 is miscible in CeO2 and ThO2, respectively. The incorporation of minor amounts of Np5+,6+ into uranium alteration phases, e.g., studtite [UO2O2 (H2O)4] or boltwoodite [K(UO2)(SiO 3OH)(H2O)1.5] , may limit the mobility of aqueous neptunyl complexes released from oxidized nuclear fuels. Np6+-incorporation into studtite requires less energy than Np5+-incorporation (e.g., with source/sink = Np2O5/UO 3 DeltaEincorp(Np6+) = 0.42 eV and DeltaEincorp(Np5+) = 1.12 eV). In addition, Np6+ is completely miscible in studtite at room temperature with respect to a hypothetical Np6+-studtite. Electronic structure calculations provide insight into Np-bonding in studtite. The Np 5f orbitals are within the band gap of studtite, resulting in the narrowing of the band gap from 2.29 eV for studtite to 1.09 eV for Np-incorporated studtite. Three charge-balancing mechanisms for the substitution of Np5+ for U6+ were compared: i) addition of H+ [DeltaEincorp(bolt) = 0.79 eV; DeltaEincorp(stud) = 1.12 eV], ii) interlayer coupled substitution [DeltaEincorp (bolt) = 1.40 eV], iii) intra-layer coupled-substitution [DeltaEincorp(bolt) = 0.86 eV]. Solid-solution calculations of the intra-layer coupled-substitution mechanism, where Np 5+ and P5+ substitute for U6+ and Si 4+, predict an incorporation limit of 585 ppm at 300 °C.

High surface area ThO/sub 2/ catalyst

DOEpatents

Colmenares, C.A.; Somorjai, G.A.; Maj, J.J.

1983-06-21

A ThO/sub 2/ catalyst having a high surface area of about 80 to 125m/sup 2//g is synthesized. The compound is synthesized by simultaneously mixing an aqueous solution of ThNO/sub 3/(NO/sub 3/)/sub 4/.4H/sub 2/O with an aqueous solution of Na/sub 2/CO/sub 3/.H/sub 2/O, to produce a solution and solid ThOCO/sub 3/. The solid ThOCO/sub 3/ is separated from the solution, and then calcined at a temperature of about 225 to 300/sup 0/C for about 40 to 55 hours to produce ThO/sub 2/. The ThO/sub 2/ catalyst produced includes Na present as a substitutional cation in an amount equal to about 5 to 10 at. %.

High surface area ThO.sub.2 catalyst and method of preparing it

DOEpatents

Colmenares, Carlos A.; Somorjai, Gabor A.; Maj, Joseph J.

1985-01-01

A ThO.sub.2 catalyst having a high surface area of about 80-125 m.sup.2 /g is synthesized. The compound is synthesized by simultaneously mixing an aqueous solution of ThNO.sub.3 (NO.sub.3).sub.4.4H.sub.2 O with an aqueous solution of Na.sub.2 CO.sub.3.H.sub.2 O, to produce a solution and solid ThOCO.sub.3. The solid ThOCO.sub.3 is separated from the solution, and then calcined at a temperature of about 225.degree.-300.degree. C. for about 40-55 hours to produce ThO.sub.2. The ThO.sub.2 catalyst produced includes Na present as a substitutional cation in an amount equal to about 5-10 atom percent.

Structural modifications of polymethacrylates: impact on thermal behavior and release characteristics of glassy solid solutions.

PubMed

Claeys, Bart; De Coen, Ruben; De Geest, Bruno G; de la Rosa, Victor R; Hoogenboom, Richard; Carleer, Robert; Adriaensens, Peter; Remon, Jean Paul; Vervaet, Chris

2013-11-01

Polymethacrylates such as Eudragit® polymers are well established as drug delivery matrix. Here, we synthesize several Eudragit E PO (n-butyl-, dimethylaminoethyl-, methyl-methacrylate-terpolymer) analogues via free radical polymerization. These polymers are processed via hot melt extrusion, followed by injection molding and evaluated as carriers to produce immediate release solid solution tablets. Three chemical modifications increased the glass transition temperature of the polymer: (a) substitution of n-butyl by t-butyl groups, (b) reduction of the dimethylaminoethyl methacrylate (DMAEMA) content, and (c) incorporation of a bulky isobornyl repeating unit. These structural modifications revealed the possibility to increase the mechanical stability of the tablets via altering the polymer Tg without influencing the drug release characteristics and glassy solid solution forming properties. The presence of DMAEMA units proved to be crucial with respect to API/polymer interaction (essential in creating glassy solid solutions) and drug release characteristics. Moreover, these chemical modifications accentuate the need for a more rational design of (methacrylate) polymer matrix excipients for drug formulation via hot melt extrusion and injection molding. Copyright © 2013 Elsevier B.V. All rights reserved.

Influence of anionic substitution on the electrolyte electroreflectance study of band edge transitions in single crystal Cu2ZnSn(SxSe1-x)4 solid solutions

NASA Astrophysics Data System (ADS)

Levcenco, S.; Dumcenco, D.; Wang, Y. P.; Huang, Y. S.; Ho, C. H.; Arushanov, E.; Tezlevan, V.; Tiong, K. K.

2012-06-01

Single crystals of Cu2ZnSn(SxSe1-x)4 (CZTSSe) solid solutions were grown by chemical vapor transport technique using iodine trichloride as a transport agent. As confirmed by X-ray investigations, the as-grown CZTSSe solid solutions are single phase and crystallized in kesterite structure. The lattice parameters of CZTSSe were determined and the S contents of the obtained crystals were estimated by Vegard's law. The composition dependent band gaps of CZTSSe solid solutions were studied by electrolyte electroreflectance (EER) measurements at room temperature. From a detailed lineshape fit of the EER spectra, the band gaps of CZTSSe were determined accurately and were found to decrease almost linearly with the increase of Se content, which agreed well with the recent theoretical first-principle calculations by S. Chen, A. Walsh, J.H. Yang, X.G. Gong, L. Sun, P. X. Yang, J.H. Chu, S.H. Wei, Phys. Rev. B 83 (2011) 125201 (5pp).

Solution- and solid-phase parallel synthesis of 4-alkoxy-substituted pyrimidines with high molecular diversity.

PubMed

Font, David; Heras, Montserrat; Villalgordo, José M

2003-01-01

A simple and straightforward methodology toward the synthesis of novel 2,6-disubstituted-4-alkoxypyrimidine derivatives of type 16 and 19 has been developed. This methodology, initially developed in solution, can be perfectly adapted to the solid support under analogous conditions, taking full advantage of automated parallel synthesis systems. This successful methodology benefits from the key role played by the thioether linkage placed at the 2-position in 3, 9, or 13 in a double manner: on one side, the steric effect exerted by the thioether linkage is likely to be responsible for the very high observed selectivity toward the formation of the O-alkylation products. On the other side, this sulfur linkage can serve not only as a robust point of attachment for the heterocycle, stable to a number of reaction conditions, but also as a means of introducing a new element of diversity through activation to the corresponding sulfone (safety-catch linker concept) and subsequent ipso-substitution reaction with a variety of different N-nucleophiles.

Solid solubility, phase transitions, thermal expansion, and compressibility in Sc{sub 1−x}Al{sub x}F{sub 3}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morelock, Cody R.; Gallington, Leighanne C.; Wilkinson, Angus P., E-mail: angus.wilkinson@chemistry.gatech.edu

2015-02-15

With the goal of thermal expansion control, the synthesis and properties of Sc{sub 1−x}Al{sub x}F{sub 3} were investigated. The solubility limit of AlF{sub 3} in ScF{sub 3} at ∼1340 K is ∼50%. Solid solutions (x≤0.50) were characterized by synchrotron powder diffraction at ambient pressure between 100 and 900 K and at pressures <0.414 GPa while heating from 298 to 523 K. A phase transition from cubic to rhombohedral is observed. The transition temperature increases smoothly with Al{sup 3+} content, approaching 500 K at the solid solubility limit, and also upon compression at fixed Al{sup 3+} content. The slope of themore » pressure–temperature phase boundary is ∼0.5 K MPa{sup −1}, which is steep relative to that for most symmetry-lowering phase transitions in perovskites. The volume coefficient of thermal expansion (CTE) for the rhombohedral phase is strongly positive, but the cubic-phase CTE varies from negative (x<0.15) to near-zero (x=0.15) to positive (x>0.20) between ∼600 and 800 K. The cubic solid solutions elastically stiffen on heating, while Al{sup 3+} substitution causes softening at a given temperature. - Graphical abstract: The cubic-phase coefficient of thermal expansion for Sc{sub 1−x}Al{sub x}F{sub 3}(solubility limit ∼50% at ∼1340 K) becomes more positive with increased Al{sup 3+} substitution, but the average isothermal bulk modulus decreases (elastic softening). - Highlights: • The solubility limit of AlF{sub 3} in ScF{sub 3} at ∼1340 K is ∼50%. • The phase transition temperature of Sc{sub 1−x}Al{sub x}F{sub 3} increases smoothly with x. • The cubic-phase volume CTE varies from negative to positive with increasing x. • The cubic solid solutions elastically stiffen on heating. • Al{sup 3+} substitution causes softening at a given temperature.« less

Self-assembled nanostructures of linear arylacetylenes and their aza-substituted analogues

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, Jia-Ju; Department of Physics and Materials Science and Centre of Super Diamond and Advanced Films; Yang, Xiong-Bo

2016-06-15

A series of linear phenylene ethynylene molecules have been synthesized, and aza-substitution has been used as a strategy to fine-tune the properties of the molecules. All the compounds exhibited pure blue emission both in solution and solid state, and fluorescence quantum yields as high as 0.66, 0.63 and 0.82 were found in chloroform solutions. The well-defined nanostructures such as quasi-cubes, cubes and rods were fabricated by self-assembly method from these compounds. The photophysical properties and aggregation behavior of self-assembled structures were analyzed in detail. The morphology as well as photophysical properties of these nanostructures have been tuned with selective requirements.

Influence of isotopic disorder on solid state amorphization and polyamorphism in solid H2O -D2O solutions

NASA Astrophysics Data System (ADS)

Gromnitskaya, E. L.; Danilov, I. V.; Lyapin, A. G.; Brazhkin, V. V.

2015-10-01

We present a low-temperature and high-pressure ultrasonic study of elastic properties of isotopic H2O-D2O solid solutions, comparing their properties with those of the isotopically pure H2O and D2O ices. Measurements were carried out for solid state amorphization (SSA) from 1h to high-density amorphous (HDA) ice upon compression up to 1.8 GPa at 77 K and for the temperature-induced (77 -190 K ) u-HDA (unrelaxed HDA) → e-HDA (expanded HDA) → low-density amorphous (LDA )→1 c cascade of ice transformations near room pressure. There are many similarities in the elasticity behaviour of H2O ,D2O , and H2O-D2O solid solutions, including the softening of the shear elastic modulus as a precursor of SSA and the HDA →LDA transition. We have found significant isotopic effects during H/D substitution, including elastic softening of H2O -D2O solid solutions with respect to the isotopically pure ices in the case of the bulk moduli of ices 1c and 1h and for both bulk and shear elastic moduli of HDA ice at high pressures (>1 GPa ) . This softening is related to the configurational isotopic disorder in the solid solutions. At low pressures, the isotope concentration dependence of the elastic moduli of u-HDA ice changes remarkably and becomes monotonic with pronounced change of the bulk modulus (≈20 %) .

Natural Cr3+-rich ettringite: occurrence, properties, and crystal structure

NASA Astrophysics Data System (ADS)

Seryotkin, Yurii V.; Sokol, Ella V.; Kokh, Svetlana N.; Murashko, Mikhail N.

2017-08-01

Cr3+-rich ettringite with Cr3+→Al substitution and Cr/(Cr + Al) ratios up to 0.40-0.50 was found in mineral assemblages of the Ma'aleh Adumim area of Mottled Zone (Judean Desert). The Cr3+-rich compositions were the latest in the thaumasite → ettringite-thaumasite solid solution → ettringite → ettringite-bentorite solid solution series. The mineral-forming solution was enriched in Cr3+ and had a pH buffered by afwillite at 11-12. Chromium was inherited from larnite rocks produced by high-temperature combustion metamorphic alteration of bioproductive calcareous sediments. The Cr/(Cr + Al) ratios are within 0.10-0.15 in most of the analysed crystals. This degree of substitution imparts pink colouration to the crystals, but does not affect their habit (a combination of monohedra and a prism). The habit changes to pyramid faces in coarse and later Cr3+-bearing crystals as Cr/(Cr + Al) ratios increase abruptly to 0.40-0.50. Single-crystal XRD analysis of one Cr-free and two Cr3+-rich samples and their structure determination and refinement indicate that the Cr-rich crystals (with Cr/(Cr + Al) to 0.3) preserve the symmetry and metrics of ettringite. The Ca-O bonding network undergoes differentiation with increase of Cr3+ concentration at octahedral M sites. The compression of Ca2 and expansion of Ca1 polyhedra sub-networks correlates with the degree of Cr3+→Al substitution.

Calorimetric determination of energetics of solid solutions of UO 2+ x with CaO and Y 2O 3

NASA Astrophysics Data System (ADS)

Mazeina, Lena; Navrotsky, Alexandra; Greenblatt, Martha

2008-02-01

Quantitative study of thermodynamic properties of solid solutions of UO 2+ x with divalent and trivalent oxides is important for predicting the behavior of oxide fuel. Although early literature work measured vapor pressure in some of these solid solutions, direct calorimetric measurements of enthalpies of formation have been hampered by the refractory nature of such oxides. First measurements of the enthalpies of formation in the systems UO 2+ x-CaO and UO 2+ x-YO 1.5, obtained by high-temperature oxide melt solution calorimetry, are reported. Both systems show significantly negative (exothermic) heats of formation from binary oxides (UO 2, plus O 2 and CaO or YO 1.5, as well as from UO 2 plus UO 3 and CaO or YO 1.5), consistent with reported free energy measurements in the urania-yttria system. The energetic contributions of oxygen content (oxidation of U 4+) and of charge balanced ionic substitution as well as defect clustering are discussed. Behavior of urania-yttria is compared to that of corresponding systems in which the tetravalent ion is Ce, Zr, or Hf. The substantial additional stability in the solid solutions compared to pure UO 2+ x may retard, in both thermodynamic and kinetic sense, the oxidation and leaching of spent fuel to form aqueous U 6+ and solid uranyl phases.

Molten-salt synthesis and composition-dependent luminescent properties of barium tungsto-molybdate-based solid solution phosphors

NASA Astrophysics Data System (ADS)

Xiang-Hong, He; Zhao-Lian, Ye; Ming-Yun, Guan; Ning, Lian; Jian-Hua, Sun

2016-02-01

Pr3+-activated barium tungsto-molybdate solid solution phosphor Ba(Mo1-zWz)O4:Pr3+ is successfully fabricated via a facile molten-salt approach. The as-synthesized microcrystal is of truncated octahedron and exhibits deep-red-emitting upon blue light excitation. Powder x-ray diffraction and Raman spectroscopy techniques are utilized to investigate the formation of solid solution phosphor. The luminescence behaviors depend on the resulting composition of the microcrystals with fixed Pr3+-doping concentration, while the host lattices remain in a scheelite structure. The forming solid solution via the substitution of [WO4] for [MoO4] can significantly enhance its luminescence, which may be due to the fact that Ba(Mo1-zWz)O4:Pr3+ owns well-defined facets and uniform morphologies. Owing to its properties of high phase purity, well-defined facets, highly uniform morphologies, exceptional chemical and thermal stabilities, and stronger emission intensity, the resulting solid solution phosphor is expected to find potential applications in phosphor-converted white light-emitting diodes (LEDs). Project supported by the Construction Fund for Science and Technology Innovation Group from Jiangsu University of Technology, China, the Key Laboratory of Atmospheric Environment Monitoring and Pollution Control, China (Grant No. KHK1409), the Priority Academic Program Development of Jiangsu Higher Education Institutions, China, and the National Natural Science Foundation of China (Grant No. 21373103).

Tunable Optical Properties and Increased Thermal Quenching in the Blue-Emitting Phosphor Series: Ba 2 (Y 1–x Lu x ) 5 B 5 O 17 :Ce 3+ ( x = 0–1)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hermus, Martin; Phan, Phu-Cuong; Duke, Anna C.

The preparation of cerium-substituted barium lutetium borate, Ba2Lu5B5O17:Ce3+, is achieved using high temperature solid state synthesis. This compound crystallizes in the Ba2Y5B5O17-type structure and shows an efficient blue emission (λmax = 447 nm) when excited by UV-light (λex = 340 nm) with a photoluminescent quantum yield near 90%, a fast luminescence decay time (<40 ns), and a thermal quenching temperature of 452 K. Further, preparing a solid solution following Ba2(Y1–xLux)5B5O17:Ce3+ (x = 0, 0.25, 0.50, 0.75, 1) confirms that all compounds are isostructural and follow Vegard’s law. Substituting Y3+ for Lu3+ yields a nearly constant emission spectrum that blue-shifts bymore » only 9 nm and has a consistent luminescence lifetime across the range prepared. The photoluminescent quantum yield (PLQY) and thermal quenching (T50) of the solid solution, however, are dramatically impacted by the composition, with the PLQY decreasing to ≈70% and the T50 dropping 49 K going from x = 1 to x = 0. These significant changes in the optical properties likely stem from enhanced structural rigidity as the larger, more polarizable Y3+ is substituted for the smaller, harder Lu3+ cation. These results highlight the importance of optimizing chemical bonding to improve a phosphor’s optical properties.« less

Magnetocaloric properties of rare-earth substituted DyCrO{sub 3}

DOE Office of Scientific and Technical Information (OSTI.GOV)

McDannald, A.; Jain, M., E-mail: menka.jain@uconn.edu; Department of Physics, University of Connecticut, Storrs, Connecticut 06269

Recently, there has been a focus on the need for efficient refrigeration technology without the use of expensive or harmful working fluids, especially at temperatures below 30 K. Solid state refrigeration, based on the magnetocaloric effect, provides a possible solution to this problem. The rare-earth chromites (RCrO{sub 3}), especially DyCrO{sub 3}, with its large magnetic moment dysprosium ion, are potential candidates for such an application. The Dy{sup 3+} ordering transition at low temperatures (<10 K) likely causes a large magnetocaloric response in this material. This study investigates the possibility of tuning the magnetocaloric properties through the use of rare-earth substitution. Both Y{supmore » 3+} and Ho{sup 3+} substitutions were found to decrease the magnetocaloric response by disrupting the R{sup 3+} ordering. Whereas Er{sup 3+} substitution was found to increase the magnetocaloric response, likely due to an increase in the R{sup 3+} ordering temperature. The large magnetocaloric entropy change of Er{sup 3+} substituted DyCrO{sub 3} (10.92 J/kg K with a relative cooling power of 237 J/kg at 40 kOe and 5 K) indicates that this material system is well suited for low temperature (<30 K) solid state refrigeration applications.« less

Ionic Conductivity of TlBr1-xIx(x = 0, 0.2, 1): Candidate Gamma Ray Detector

NASA Astrophysics Data System (ADS)

Bishop, S. R.; Ciampi, G.; Lee, C. D.; Kuhn, M.; Tuller, H. L.; Higgins, W.; Shah, K. S.

2012-10-01

The ionic conductivity of TlBr, TlI and their solid solutions, candidates for high energy radiation detection, was examined using impedance spectroscopy. The orthorhombic to cubic phase change in TlI was observed via a steep change in conductivity with increasing temperature, whereas the TlBr-TlI solid solution was cubic throughout the measured temperature range, in agreement with the literature. The intrinsic conductivity of the cubic phase of each material showed nearly identical behavior, indicating that I substitution for Br has little to no effect on the combined defect formation and transport parameters in the studied range. Additionally, optical transmission was correlated with I concentration.

Studies on solid solutions based on layered honeycomb-ordered phases P2-Na{sub 2}M{sub 2}TeO{sub 6} (M=Co, Ni, Zn)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berthelot, Romain; Schmidt, Whitney; Sleight, A.W.

2012-12-15

Three complete solid solutions between the layered phases P2-Na{sub 2}M{sub 2}TeO{sub 6} (M=Co, Ni, Zn) have been prepared by conventional solid state method and investigated through X-ray diffraction, magnetism and optical measurements. All compositions are characterized by a M{sup 2+}/X{sup 6+} honeycomb ordering within the slabs and crystallize in a hexagonal unit cell. However, a structural transition based on a different stacking is observed as nickel (space group P6{sub 3}/mcm) is substituted by zinc or cobalt (space group P6{sub 3}22). All compositions exhibit a paramagnetic Curie-Weiss behavior at high temperatures; and the magnetic moment values confirm the presence of Ni{supmore » 2+} and/or Co{sup 2+} cations. The low-temperature antiferromagnetic order of Na{sub 2}Ni{sub 2}TeO{sub 6} and Na{sub 2}Co{sub 2}TeO{sub 6} is suppressed by zinc substitution. The color of the obtained compositions varies from pink, to light green and white when M=Co, Ni, Zn, respectively. - Graphical abstract: The comparison between the structure of Na{sub 2}Ni{sub 2}TeO{sub 6} (left) and Na{sub 2}M{sub 2}TeO{sub 6} (M=Co, Zn) (right) evidences the stacking difference with distinct atom sequences along the hexagonal c-axis. Highlights: Black-Right-Pointing-Pointer Solid solutions between lamellar phases Na{sub 2}M{sub 2}TeO{sub 6} (M=Co, Ni, Zn) are investigated. Black-Right-Pointing-Pointer A M{sup 2+}/X{sup 6+} honeycomb ordering characterized all the compositions. Black-Right-Pointing-Pointer A structural transition is shown when Ni is replaced by Co or Zn. Black-Right-Pointing-Pointer The low-temperature AFM ordering of Na{sub 2}Ni{sub 2}TeO{sub 6} and Na{sub 2}Co{sub 2}TeO{sub 6} is suppressed by zinc substitution. Black-Right-Pointing-Pointer Color changes from pink to light green and white when M=Co, Ni, Zn, respectively.« less

Structural and magnetic characterization of the complete delafossite solid solution (CuAlO₂)₁-x(CuCrO₂)x.

PubMed

Barton, Phillip T; Seshadri, Ram; Knöller, Andrea; Rosseinsky, Matthew J

2012-01-11

We have prepared the complete delafossite solid solution series between diamagnetic CuAlO(2) and the t(2g)(3)frustrated antiferromagnet CuCrO(2). The evolution with composition x in CuAl(1-x)Cr(x)O(2) of the crystal structure and magnetic properties has been studied and is reported here. The room-temperature unit cell parameters follow the Végard law and increase with x as expected. The μ(eff) is equal to the Cr(3+) spin-only S = 3/2 value throughout the entire solid solution. Θ(CW) is negative, indicating that the dominant interactions are antiferromagnetic, and its magnitude increases with Cr substitution. For dilute Cr compositions, the nearest-neighbor exchange coupling constant J(BB) was estimated by mean-field theory to be 3.0 meV. Despite the sizable Θ(CW), long-range antiferromagnetic order does not develop until x is almost 1, and is preceded by glassy behavior. The data presented here, and those on dilute Al substitution from Okuda et al, suggest that the reduction in magnetic frustration due to the presence of non-magnetic Al does not have as dominant an effect on magnetism as chemical disorder and dilution of the magnetic exchange. For all samples, the 5 K isothermal magnetization does not saturate in fields up to 5 T and minimal hysteresis is observed. The presence of antiferromagnetic interactions is clearly evident in the sub-Brillouin behavior with a reduced magnetization per Cr atom. An inspection of the scaled Curie plot reveals that significant short-range antiferromagnetic interactions occur in CuCrO(2) above its Néel temperature, consistent with its magnetic frustration. Uncompensated short-range behavior is present in the Al-substituted samples and is likely a result of chemical disorder.

Structural and magnetic characterization of the complete delafossite solid solution (CuAlO2)1-x(CuCrO2)x

NASA Astrophysics Data System (ADS)

Barton, Phillip T.; Seshadri, Ram; Knöller, Andrea; Rosseinsky, Matthew J.

2012-01-01

We have prepared the complete delafossite solid solution series between diamagnetic CuAlO2 and the t2g3frustrated antiferromagnet CuCrO2. The evolution with composition x in CuAl1-xCrxO2 of the crystal structure and magnetic properties has been studied and is reported here. The room-temperature unit cell parameters follow the Végard law and increase with x as expected. The μeff is equal to the Cr3+ spin-only S = 3/2 value throughout the entire solid solution. ΘCW is negative, indicating that the dominant interactions are antiferromagnetic, and its magnitude increases with Cr substitution. For dilute Cr compositions, the nearest-neighbor exchange coupling constant JBB was estimated by mean-field theory to be 3.0 meV. Despite the sizable ΘCW, long-range antiferromagnetic order does not develop until x is almost 1, and is preceded by glassy behavior. The data presented here, and those on dilute Al substitution from Okuda et al, suggest that the reduction in magnetic frustration due to the presence of non-magnetic Al does not have as dominant an effect on magnetism as chemical disorder and dilution of the magnetic exchange. For all samples, the 5 K isothermal magnetization does not saturate in fields up to 5 T and minimal hysteresis is observed. The presence of antiferromagnetic interactions is clearly evident in the sub-Brillouin behavior with a reduced magnetization per Cr atom. An inspection of the scaled Curie plot reveals that significant short-range antiferromagnetic interactions occur in CuCrO2 above its Néel temperature, consistent with its magnetic frustration. Uncompensated short-range behavior is present in the Al-substituted samples and is likely a result of chemical disorder.

Bond length variation in Zn substituted NiO studied from extended X-ray absorption fine structure

NASA Astrophysics Data System (ADS)

Singh, S. D.; Poswal, A. K.; Kamal, C.; Rajput, Parasmani; Chakrabarti, Aparna; Jha, S. N.; Ganguli, Tapas

2017-06-01

Bond length behavior for Zn substituted NiO is determined through extended x-ray absorption fine structure (EXAFS) measurements performed at ambient conditions. We report bond length value of 2.11±0.01 Å for Zn-O of rock salt (RS) symmetry, when Zn is doped in RS NiO. Bond length for Zn substituted NiO RS ternary solid solutions shows relaxed behavior for Zn-O bond, while it shows un-relaxed behavior for Ni-O bond. These observations are further supported by first-principles calculations. It is also inferred that Zn sublattice remains nearly unchanged with increase in lattice parameter. On the other hand, Ni sublattice dilates for Zn compositions up to 20% to accommodate increase in the lattice parameter. However, for Zn compositions more than 20%, it does not further dilate. It has been attributed to the large disorder that is incorporated in the system at and beyond 20% of Zn incorporation in the cubic RS lattice of ternary solid solutions. For these large percentages of Zn incorporation, the Ni and the Zn atoms re-arrange themselves microscopically about the same nominal bond length rather than systematically increase in magnitude to minimize the energy of the system. This results in an increase in the Debye-Waller factor with increase in the Zn concentration rather than a systematic increase in the bond lengths.

Thermodynamics of magnesian calcite solid-solutions at 25°C and 1 atm total pressure

USGS Publications Warehouse

Busenberg, Eurybiades; Plummer, Niel

1989-01-01

The stability of magnesian calcites was reexamined, and new results are presented for 28 natural inorganic, 12 biogenic, and 32 synthetic magnesian calcites. The magnesian calcite solid-solutions were separated into two groups on the basis of differences in stoichiometric solubility and other physical and chemical properties. Group I consists of solids of mainly metamorphic and hydrothermal origin, synthetic calcites prepared at high temperatures and pressures, and synthetic solids prepared at low temperature and very low calcite supersaturations () from artificial sea water or NaClMgCl2CaCl2solutions. Group I solids are essentially binary s of CaCO2 and MgCO2, and are thought to be relatively free of structural defects. Group II solid-solutions are of either biogenic origin or are synthetic magnesian calcites and protodolomites (0–20 and ∼ 45 mole percent MgCO3) prepared at high calcite supersaturations () from NaClNa2SO4MgCl2CaCl2 or NaClMgCl2CaCl2 solutions. Group II solid-solutions are treated as massively defective solids. The defects include substitution foreign ions (Na+ and SO42−) in the magnesian calcite lattice (point defects) and dislocations (~2 · 109 cm−2). Within each group, the excess free energy of mixing, GE, is described by the mixing model , where x is the mole fraction of the end-member Ca0.5Mg0.5CO3 in the solid-solution. The values of A0and A1 for Group I and II solids were evaluated at 25°C. The equilibrium constants of all the solids are closely described by the equation ln , where KC and KD are the equilibrium constants of calcite and Ca0.5Mg0.5CO3. Group I magnesian calcites were modeled as sub-regular solid-solutions between calcite and dolomite, and between calcite and “disordered dolomite”. Both models yield almost identical equilibrium constants for these magnesian calcites. The Group II magnesian calcites were modeled as sub-regular solid-solutions between defective calcite and protodolomite. Group I and II solid-solutions differ significantly in stability. The rate of crystal growth and the chemical composition of the aqueous solutions from which the solids were formed are the main factors controlling stoichiometric solubility of the magnesian calcites and the density of crystal defects. The literature on the occurrence and behavior of magnesian calcites in sea water and other aqueous solutions is also examined.

Inhibition of the solid state transformation of carbamazepine in aqueous solution: impact of polymeric properties.

PubMed

Gift, Alan D; Hettenbaugh, Jacob A; Quandahl, Rachel A; Mapes, Madison

2017-11-06

The effects of polymers on the anhydrate-to-hydrate transformation of carbamazepine (CBZ) was investigated. The three types of polymers studied were polyvinylpyrrolidone (PVP), polyvinyl alcohol (PVA) and substituted celluloses which included hydroxypropyl methylcellulose (HPMC) and methylcellulose (MC). Anhydrous CBZ was added to dilute aqueous polymer solutions and Raman spectroscopy measurements were collected to monitor the kinetics of the solution-mediated transformation to CBZ dihydrate. Polymers exhibiting the greatest inhibition were able to reduce the growth phase of the solution-mediated transformation and change the habit of the hydrate crystal indicating polymer adsorption to the hydrate crystal surface as the mechanism of inhibition. The results of the various polymers showed that short chain substituted celluloses (HPMC and MC) inhibited the CBZ transformation to a much greater extent than longer chains. The same trend was observed for PVP and PVA, but to a lesser extent. These chain length effects were attributed to changes in polymer confirmation when adsorbed on the crystal surface. Additionally, decreasing the percentage of hydroxyl groups on the PVA polymer backbone reduced the ability of the polymer to inhibit the transformation and changing the degree of substitutions of methyl and hydroxypropyl groups on the cellulosic polymer backbone had no effect on the transformation.

Effect of Te substitution on crystal structure and transport properties of AgBiSe2 thermoelectric material.

PubMed

Goto, Y; Nishida, A; Nishiate, H; Murata, M; Lee, C H; Miura, A; Moriyoshi, C; Kuroiwa, Y; Mizuguchi, Y

2018-02-20

Silver bismuth diselenide (AgBiSe 2 ) has attracted much attention as an efficient thermoelectric material, owing to its intrinsically low lattice thermal conductivity. While samples synthesized using a solid-state reaction showed n-type conductivity and their dimensionless figure of merit (ZT) reached ∼1 by electron doping, theoretical calculations predicted that a remarkably high thermoelectric performance can be achieved in p-type AgBiSe 2 . In this paper, we present the effect of Te substitution on the crystal structure and thermoelectric properties of AgBiSe 2 , expecting p-type conductivity due to the shallowing of the energy potential of the valence band. We found that all AgBiSe 2-x Te x (x = 0-0.8) prepared using a solid-state reaction exhibits n-type conductivity from 300 to 750 K. The room-temperature lattice thermal conductivity decreased to as low as 0.3 W m -1 K -1 by Te substitution, which was qualitatively described using the point defect scattering model for the solid solution. We show that ZT reaches ∼0.6 for x = 0.8 at a broad range of temperatures, from 550 to 750 K, due to the increased power factor, although the carrier concentration has not been optimized yet.

Photocatalytic water oxidation by a pyrochlore oxide upon irradiation with visible light: rhodium substitution into yttrium titanate.

PubMed

Kiss, Borbala; Didier, Christophe; Johnson, Timothy; Manning, Troy D; Dyer, Matthew S; Cowan, Alexander J; Claridge, John B; Darwent, James R; Rosseinsky, Matthew J

2014-12-22

A stable visible-light-driven photocatalyst (λ≥450 nm) for water oxidation is reported. Rhodium substitution into the pyrochlore Y2 Ti2 O7 is demonstrated by monitoring Vegard's law evolution of the unit-cell parameters with changing rhodium content, to a maximum content of 3 % dopant. Substitution renders the solid solutions visible-light active. The overall rate of oxygen evolution is comparable to WO3 but with superior light-harvesting and surface-area-normalized turnover rates, making Y2 Ti1.94 Rh0.06 O7 an excellent candidate for use in a Z-scheme water-splitting system. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saidov, A. S., E-mail: amin@uzsci.net; Usmonov, Sh. N., E-mail: sh-usmonov@rambler.ru; Saidov, M. S.

(Si{sub 2}){sub 1−x−y}(Ge{sub 2}){sub x}(GaAs){sub y} substitutional solid solutions (0 ≤ x ≤ 0.91, 0 ≤ y ≤ 0.94) are grown by liquid-phase epitaxy from a Pb-based solution-melt on Si substrates with the (111) crystallographic orientation. The chemical composition of the epitaxial films is studied by X-rays probe microanalysis, and the distribution profile of solid solution components is determined. Spectral dependences of the photosensitivity and photoluminescence of the n-Si-p(Si{sub 2}){sub 1−x−y}(Ge{sub 2}){sub x}(GaAs){sub y} heterostructures are studied at room and liquid-nitrogen temperatures. Two maxima are found in the photoluminescence spectra of the (Si{sub 2}){sub 1−x−y}(Ge{sub 2}){sub x}(GaAs){sub y} films (0more » ≤ x ≤ 0.91, 0 ≤ y ≤ 0.94) against the background of a broad emission spectrum. The fundamental maximum with an energy of 1.45 eV is caused by the band-to-band recombination of solid solution carriers, and an additional maximum with an energy of 1.33 eV is caused by the recombination of carriers with the participation of impurity levels of the Si-Si bond (Si{sub 2} is covalently coupled with the tetrahedral lattice of the solid solution host)« less

Synthesis and Photoluminescent Properties of Arylethynyl substituted 9,10-Anthraquinones

NASA Technical Reports Server (NTRS)

Yang, Jin-Hua; Dass, Amala; Sotiriou-Leventis, Chariklia; Leventis, Nicholas

2003-01-01

A series of arylethynyl substituted anthraquinones were synthesized via Sonogashira coupling reactions of 2,7- dibromo-, 2,6-dibromo- and 2-bromoanthraquinone with para-substituted phenylacetylenes. While the redox properties of those compounds are almost insensitive to substitution, their absorption maxima are linearly related to the Hammett constants for electron donating and electron withdrawing groups separately. All compounds are photoluminescent both in solution (quantum yield of emission approximately 2%) and as solids. X-ray crystallographic characterization of 2,7-bisphenylethynyl anthraquinone indicates a monoclinic p2(l/n) space group and no indication for pi-overlap that would promote self-quenching. The emission maxima are red- shifted by both electron donating and electron withdrawing groups alike. The Stokes shifts of all compounds are significant and are correlated to the electronic properties of the substituents. The reduced forms of these compounds are also photoluminescent and the emission originates from the dihydroanthraquinone core.

Effect of Isovalent Substitution on the Electronic Structure and Thermoelectric Properties of the Solid Solution α-As2Te3-xSex (0 ≤ x ≤ 1.5).

PubMed

Vaney, Jean-Baptiste; Delaizir, Gaëlle; Wiendlocha, Bartlomiej; Tobola, Janusz; Alleno, Eric; Piarristeguy, Andrea; Gonçalves, Antonio Pereira; Gendarme, Christine; Malaman, Bernard; Dauscher, Anne; Candolfi, Christophe; Lenoir, Bertrand

2017-02-20

We report on the influence of Se substitution on the electronic band structure and thermoelectric properties (5-523 K) of the solid solution α-As 2 Te 3-x Se x (0 ≤ x ≤ 1.5). All of the polycrystalline compounds α-As 2 Te 3-x Se x crystallize isostructurally in the monoclinic space group C2/m (No. 12, Z = 4). Regardless of the Se content, chemical analyses performed by scanning electron microscopy and electron probe microanalysis indicate a good chemical homogeneity, with only minute amounts of secondary phases for some compositions. In agreement with electronic band structure calculations, neutron powder diffraction suggests that Se does not randomly substitute for Te but exhibits a site preference. These theoretical calculations further predict a monotonic increase in the band gap energy with the Se content, which is confirmed experimentally by absorption spectroscopy measurements. Increasing x up to x = 1.5 leaves unchanged both the p-type character and semiconducting nature of α-As 2 Te 3 . The electrical resistivity and thermopower gradually increase with x as a result of the progressive increase in the band gap energy. Despite the fact that α-As 2 Te 3 exhibits very low lattice thermal conductivity κ L , the substitution of Se for Te further lowers κ L to 0.35 W m -1 K -1 at 300 K. The compositional dependence of the lattice thermal conductivity closely follows classical models of phonon alloy scattering, indicating that this decrease is due to enhanced point-defect scattering.

Single crystal growth and characterization of kagomé-lattice shandites Co3Sn2-xInxS2

NASA Astrophysics Data System (ADS)

Kassem, Mohamed A.; Tabata, Yoshikazu; Waki, Takeshi; Nakamura, Hiroyuki

2015-09-01

Single crystals of the shandite-type half metallic ferromagnet Co3Sn2S2, and its In-substituted compounds, Co3Sn2-xInxS2 (0

Evaluation of stability region for scandium-containing rare-earth garnet single crystals and their congruent-melting compositions

NASA Astrophysics Data System (ADS)

Kaurova, I. A.; Domoroshchina, E. N.; Kuz'micheva, G. M.; Rybakov, V. B.

2017-06-01

Single crystals of scandium-containing rare-earth garnets in system R-Sc-C-O (R3+=Y, Gd; C3+=Al, Ga) have been grown by the Czochralski technique. X-ray diffraction analysis has been used to refine crystal compositions. The fundamental difference between the melt compositions and compositions of grown crystals has been found (except for compositions of congruent-melting compounds, CMC). The specific features of garnet solid solution formation have been established and the ternary diagrams with real or hypothetical phases have been built. The dinamics of coordination polyhedra changes with the formation of substitutional solid solutions have been proposed based on the mathematical modeling and experimental data. Possible existence of CMC with garnet structure in different systems as well as limit content of Sc ions in dodecahedral and octahedral sites prior to their partial substitution of ions, located in other sites, have been evaluated. It was established that the redistribution of cations over crystallographic sites (antistructural point defects) due to system self-organization to maintain its stability may be accompanied by cation ordering and the symmetry change of individual polyhedrons and/or the whole crystal.

Conformational distribution of baclofen analogues by 1H and 13C NMR analysis and ab initio HF MO STO-3G or STO-3G* calculations

NASA Astrophysics Data System (ADS)

Vaccher, Claude; Berthelot, Pascal; Debaert, Michel; Vermeersch, Gaston; Guyon, René; Pirard, Bernard; Vercauteren, Daniel P.; Dory, Magdalena; Evrard, Guy; Durant, François

1993-12-01

The conformations of 3-(substituted furan-2-yl) and 3-(substituted thien-2-yl)-γ-aminobutyric acid 1-9 in solution (D 2O) are estimated from high-resolution (300 MHz) 1H NMR coupling data. Conformations and populations of conformers are calculated by means of a modified Karplus-like relationship for the vicinal coupling constants. The results are compared with X-ray crystallographic investigations (torsion angles) and ab initio HF MO ST-3G or STO-3G* calculations. 1H NMR spectral analysis shows how 1-9 in solution retain the preferred g- conformation around the C3C4 bond, as found in the solid state, while a partial rotation is set up around the C2C3 bond: the conformations about C2C3 are all highly populated in solution. The 13C spin-lattice relaxation times are also discussed.

Atomic substitutions in synthetic apatite; Insights from solid-state NMR spectroscopy

NASA Astrophysics Data System (ADS)

Vaughn, John S.

Apatite, Ca5(PO4)3X (where X = F, Cl, or OH), is a unique mineral group capable of atomic substitutions for cations and anions of varied size and charge. Accommodation of differing substituents requires some kind of structural adaptation, e.g. new atomic positions, vacancies, or coupled substitutions. These structural adaptations often give rise to important physicochemical properties relevant to a range of scientific disciplines. Examples include volatile trapping during apatite crystallization, substitution for large radionuclides for long-term storage of nuclear fission waste, substitution for fluoride to improve acid resistivity in dental enamel composed dominantly of hydroxylapatite, and the development of novel biomaterials with enhanced biocompatibility. Despite the importance and ubiquity of atomic substitutions in apatite materials, many of the mechanisms by which these reactions occur are poorly understood. Presence of substituents at dilute concentration and occupancy of disordered atomic positions hinder detection by bulk characterization methods such as X-ray diffraction (XRD) and infrared (IR) spectroscopy. Solid-state nuclear magnetic resonance (NMR) spectroscopy is an isotope-specific structural characterization technique that does not require ordered atomic arrangements, and is therefore well suited to investigate atomic substitutions and structural adaptations in apatite. In the present work, solid-state NMR is utilized to investigate structural adaptations in three different types of apatite materials; a series of near-binary F, Cl apatite, carbonate-hydroxylapatite compositions prepared under various synthesis conditions, and a heat-treated hydroxylapatite enriched in 17O. The results indicate that hydroxyl groups in low-H, near binary F,Cl apatite facilitate solid-solution between F and Cl via column reversals, which result in average hexagonal symmetry despite very dilute OH concentration ( 2 mol percent). In addition, 19F NMR spectra indicate that fluorine occupies a complex distribution of atomic positions, which give rise to complex 19F peak shapes owing to varied F-Ca distance. 13C NMR analysis of carbonate-hydroxylapatite indicates that AB-type carbonate hydroxylapatite can be prepared without the presence of sodium or heat treatment. Isotopic 17O enrichment of hydroxylapatite and 17O NMR analysis reveals distinct signals corresponding to phosphate and hydroxyl oxygens, and heat treatment under vacuum results in loss of hydroxyl signal due to decomposition to tricalcium phosphate, which was observed by powder X-Ray diffraction (PXRD).

Change in the Magnetocapacity in the Paramagnetic Region in a Cation-Substituted Manganese Selenide

NASA Astrophysics Data System (ADS)

Aplesnin, S. S.; Sitnikov, M. N.; Zhivul'ko, A. M.

2018-04-01

The capacity and the dielectric loss tangent of a Gd x Mn1- x Se ( x ≤ 0.2) solid solution have been measured in the frequency range 1-300 kHz without a magnetic field and in a magnetic field of 8 kOe in the temperature range 100-450 K, and the magnetic moment of the solid solution has been measured in a field of 8.6 kOe. The magnetocapacity effect and the change in the magnetocapacity sign have been observed in room temperature in the paramagnetic region. A correlation of the changes in the dielectric permittivity and the magnetic susceptibility with temperature has been revealed. The magnetocapacity is described using the model with orbital electron ordering and the Maxwell-Wagner model.

Self-assembly behavior of tail-to-tail superstructure formed by mono-6-O-(4-carbamoylmethoxy-benzoyl)-β-cyclodextrin in solution and the solid state.

PubMed

Xu, Zhe; Chen, Xin; Liu, Jing; Yan, Dong-Qing; Diao, Chun-Hua; Guo, Min-Jie; Fan, Zhi

2014-07-01

A novel mono-modified β-cyclodextrin (β-CD) consisting of 4-carbamoylmethoxy-benzoyl unit at the primary side was synthesized and its self-assembly behavior was determined by X-ray crystallography and NMR spectroscopy. The crystal structure shows a 'Yin-Yang'-like packing mode, in which the modified β-CD exhibits a channel superstructure formed by a tail-to-tail dimer as the repeating motif with the substituted group embedded within the hydrophobic cavity of the facing β-CD. The geometry of the substituted group is determined by the inclusion of the cavity and is further stabilized by two intermolecular hydrogen bonds between the carbonyl O atom and phenyl group. Furthermore, NMR ROESY investigation indicates that the self-assembly behavior of the substituted group within the β-CD cavity is retained in aqueous solution, and the effective binding constant Ka was calculated to be 1330 M(-1) by means of (1)H NMR titration according to iterative determination. Copyright © 2014 Elsevier Ltd. All rights reserved.

Structural, Transport and Electrochemical Properties of LiFePO4 Substituted in Lithium and Iron Sublattices (Al, Zr, W, Mn, Co and Ni)

PubMed Central

Molenda, Janina; Kulka, Andrzej; Milewska, Anna; Zając, Wojciech; Świerczek, Konrad

2013-01-01

LiFePO4 is considered to be one of the most promising cathode materials for lithium ion batteries for electric vehicle (EV) application. However, there are still a number of unsolved issues regarding the influence of Li and Fe-site substitution on the physicochemical properties of LiFePO4. This is a review-type article, presenting results of our group, related to the possibility of the chemical modification of phosphoolivine by introduction of cation dopants in Li and Fe sublattices. Along with a synthetic review of previous papers, a large number of new results are included. The possibility of substitution of Li+ by Al3+, Zr4+, W6+ and its influence on the physicochemical properties of LiFePO4 was investigated by means of XRD, SEM/EDS, electrical conductivity and Seebeck coefficient measurements. The range of solid solution formation in Li1−3xAlxFePO4, Li1−4xZrxFePO4 and Li1−6xWxFePO4 materials was found to be very narrow. Transport properties of the synthesized materials were found to be rather weakly dependent on the chemical composition. The battery performance of selected olivines was tested by cyclic voltammetry (CV). In the case of LiFe1−yMyPO4 (M = Mn, Co and Ni), solid solution formation was observed over a large range of y (0 < y ≤ 1). An increase of electrical conductivity for the substitution level y = 0.25 was observed. Electrons of 3d metals other than iron do not contribute to the electrical properties of LiFe1−yMyPO4, and substitution level y > 0.25 leads to considerably lower values of σ. The activated character of electrical conductivity with a rather weak temperature dependence of the Seebeck coefficient suggests a small polaron-type conduction mechanism. The electrochemical properties of LiFe1−yMyPO4 strongly depend on the Fe substitution level. PMID:28809235

Oxone/Fe[superscript 2+] Degradation of Food Dyes: Demonstration of Catalyst-Like Behavior and Kinetic Separation of Color

ERIC Educational Resources Information Center

Nalliah, Ruth E.

2015-01-01

A demonstration of the degradation of food coloring dyes by oxidation via the Fenton reaction can be substituted with a simpler demonstration using the oxidant oxone with iron(II) ions as an activator. The addition of small amounts of solid oxone and iron(II) sulfate to solutions containing mixtures of food coloring results in successive…

Investigation of the system ThO 2-NpO 2-P 2O 5. Solid solutions of thorium-neptunium (IV) phosphate-diphosphate

NASA Astrophysics Data System (ADS)

Dacheux, N.; Thomas, A. C.; Brandel, V.; Genet, M.

1998-11-01

Considering that phosphate matrices could be potential candidates for the immobilization of actinides or for the final disposal of the excess plutonium from dismantled nuclear weapons, the chemistry of thorium phosphates has been re-examined. In the ThO 2-P 2O 5 system, the thorium phosphate-diphosphate Th 4(PO 4) 4P 2O 7 (TPD) can be synthesized by wet and dry chemical processes. The substitution of thorium by other tetravalent actinides like uranium or plutonium can be obtained for 0 < x < 3.0 and 0 < x < 1.63, respectively. In this work, we report the chemical conditions of synthesis of thorium-neptunium (IV) phosphate-diphosphate solid solutions Th 4- xNp x(PO 4) 4P 2O 7 (TNPD) with 0 < x < 1.6 from a mixture of thorium and neptunium (IV) nitrates and concentrated phosphoric acid. From the variation of the cell parameters and volume, the maximum substitution of Th 4+ by Np 4+ in the TPD structure is evaluated to 2.08 (which corresponds to about 52 mol% of thorium replaced by neptunium (IV)). The field of existence of solid solutions Th 4- xU- xNp- xPuU xUNp xNpPu xPu(PO 4)4P 2O 7 has been calculated. These solid solutions should be synthesized for 5 xU+7 xNp+9 xPu⩽15. In the NpO 2-P 2O 5 system, the unit cell parameters of Np 2O(PO 4) 2 were refined by analogy with U 2O(PO 4) 2 which crystallographic data have been published recently. For Np 2O(PO 4) 2 the unit cell is orthorhombic with the following cell parameters: a=7.033(2) Å, b=9.024(3) Å, c=12.587(6) Å and V=799(1) Å 3. The unit cell parameter obtained for α-NpP 2O 7 ( a=8.586(1) Å) is in good agreement with those already reported in literature.

Pyrochlore structure and spectroscopic studies of titanate ceramics. A comparative investigation on SmDyTi2O7 and YDyTi2O7 solid solutions

NASA Astrophysics Data System (ADS)

Garbout, A.; Férid, M.

2018-06-01

Considering the features in changing the structure and properties of rare earth titanates pyrochlores, the substituted Dy2Ti2O7 may be very attractive for various applications. Effect of Sm and Y substitution on the structural properties of Dy2Ti2O7 ceramic was established. These ceramics were prepared by solid-state reaction and characterized by X-ray diffraction and Raman spectroscopy. Both analysis show that YDyTi2O7 with the pyrochlore structure is obtained after heating at 1400 °C, but SmDyTi2O7 has already formed after sintering at 1200 °C. SEM images revealed that the average grain size was increased with the increase of heating temperature, and an un-homogeneous grain growth was detected. The average size was about 37 nm and 135 nm for the SmDyTi2O7 and YDyTi2O7 particles, respectively. Structural Rietveld refinements indicate that all prepared ceramics crystallize in cubic structure with space group of Fd3m. The refined cell parameters demonstrate an almost linear correlation with the ionic radius of Ln3+. The vibrational spectra revealed that the positions of bands are sensitive to the Ln3+-ionic radius, and the Tisbnd O bond strength decreased linearly with the increase of cubic lattice parameter. Raman spectra indicate that the wavenumber of Osbnd Tisbnd O bending mode is considerably shifted to lower region with increasing in mass of the Ln atom. This paper provides solid foundations for additional research of these solid solutions, which are very attractive for different fields as promising catalytic compounds for combustion applications or as frustrated magnetic pyrochlore ceramics.

Enhanced ferromagnetic order in Sr{sub 4}Mn{sub 3}O{sub 3}(GeO{sub 4}){sub 3} featuring canted [MnO{sub 4}]{sub ∞} spin chains of mixed-valent Mn(III)/Mn(IV). Aliovalent substitution of the Sr{sub 4−x}Ln{sub x}Mn{sup III}{sub 2+x}Mn{sup IV}{sub 1−x}O{sub 3}(GeO{sub 4}){sub 3} solid-solution

DOE Office of Scientific and Technical Information (OSTI.GOV)

West, J. Palmer; Sulejmanovic, Dino; Becht, Gregory

2013-10-15

Crystals of Sr{sub 4−x}Ln{sub x}Mn{sub 3}O{sub 3}(GeO{sub 4}){sub 3} (x=0; x∼0.15 for Ln=La, Pr, Nd, Sm. Eu, Gd, Dy; x∼0.3 for Ln=Gd) were isolated upon using high-temperature, solid-state methods in molten-salt media. These compounds are isostructural with the previously reported Na{sub 3}LnMn{sub 3}O{sub 3}(AsO{sub 4}){sub 3} (Ln=La, Sm, Gd) series that contains the same [MnO{sub 4}]{sub ∞} spin chains. The synthesis of the Sr{sub 4}Mn{sub 3}O{sub 3}(GeO{sub 4}){sub 3} (x=0) phase was carried out by a double aliovalent substitution with respect to the Sr{sup 2+} and Ge{sup 4+} ions that replace Na{sup +}/Ln{sup 3+} and As{sup 5+} in Na{sub 3}LnMn{submore » 3}O{sub 3}(AsO{sub 4}){sub 3}, respectively. The title series contains mixed-valent Mn(III)/Mn(IV) and shows a limited range of solid solution, both of which were not observed in the previously reported Na{sub 3}LnMn{sub 3}O{sub 3}(AsO{sub 4}){sub 3} series. To form the Sr{sub 4−x}Ln{sub x}Mn{sub 3}O{sub 3}(GeO{sub 4}){sub 3} solid solution, one of the Sr{sup 2+} sites, i.e., the original Ln-site in Na{sub 3}LnMn{sub 3}O{sub 3}(AsO{sub 4}){sub 3}, is partially substituted by Ln{sup 3+} in a statistical disorder of Sr{sub 1−x}/Ln{sub x}. Initial magnetic investigations of selected derivatives reveal higher ferromagnetic ordering temperatures than those reported for the Na{sub 3}LnMn{sub 3}O{sub 3}(AsO{sub 4}){sub 3} series, presumably attributed to a lesser degree of canting as a result of introducing non-Jahn–Teller Mn{sup 4+} ions. Also intriguing is the observation of multiple anomalies at low temperatures which appear to be of electronic origins. - Graphical abstract: Sr{sub 4−x}Ln{sub x}Mn(III){sub 2+x}Mn(IV){sub 1−x}O{sub 3}(GeO{sub 4}){sub 3}. Display Omitted - Highlights: • Double aliovalent substitution: Sr{sub 4}Mn{sub 3}O{sub 3}(GeO{sub 4}){sub 3} with respect to Na{sub 3}LnMn{sub 3}O{sub 3}(AsO{sub 4}){sub 3}. • Solid solution with respect to statistical disorder of Sr{sub 1−x}Ln{sub x} in one of the two Sr sites. • Mn{sup 3+}/Mn{sup 4+} magnetic ions are spatially arranged in a triangular kagomé fashion. • Enhanced ferromagnetic ordering attributed to doping non-Jahn–Teller Mn{sup 4+}.« less

Structural and magnetic characterization of the complete delafossite solid solution (CuAlO2)1-x(CuCrO2)x

NASA Astrophysics Data System (ADS)

Barton, Phillip; Seshadri, Ram; Knöller, Andrea; Rosseinsky, Matthew

2012-02-01

We have prepared the complete delafossite solid solution between diamagnetic CuAlO2 and the t2g^3 frustrated antiferromagnet CuCrO2. The crystal structure and magnetism were studied with powder x-ray diffraction and magnetometry. The unit cell parameters follow the V'egard law and μeff is equal to the Cr^3+ spin-only S = 3/2 value. θCW is negative and its magnitude increases with Cr substitution. For dilute Cr compositions, JBB was estimated by mean-field theory to be 3.0,eV. Despite the sizable θCW, long-range antiferromagnetic order does not develop until x is almost 1, and is preceeded by glassy behavior. For all samples, the 5,isothermal magnetization is sub-Brillouin and does not saturate in fields up to 5,. A scaled inverse susceptibility plot reveals that significant short-range antiferromagnetic interactions occur in CuCrO2 above its N'eel temperature. Additionally, the Al-substituted samples exhibit uncompensated short-range behavior and x = 0.75 shows glassy characteristics. It is suggested that reduction in magnetic frustration due to the presence of non-magnetic Al does not have as dominant an effect on magnetism as do chemical disorder and dilution of magnetic exchange.

C sbnd H…F hydrogen bonds as the organising force in F-substituted α-phenyl cinnamic acid aggregates studied by the combination of FTIR spectroscopy and computations

NASA Astrophysics Data System (ADS)

Tolnai, B.; Kiss, J. T.; Felföldi, K.; Pálinkó, I.

2009-04-01

Various F-substituted E-2,3-diphenyl propenoic acid molecules were synthesised and their aggregation behaviour was studied by experimental (FT-IR spectroscopy) and computational (semiempirical and DFT) methods. Experimental approach embraced the identification of potential hydrogen bonding sites through finding the relevant IR bands and monitoring their shifts upon increasing the acid concentration and on going to the solid state. It was found that fluorine engaged in C sbnd H…F hydrogen bonding easily, where the carbon atom could be of any kind available in the molecule (aromatic, aliphatic or olefinic). Shifts were found even in moderately concentrated solutions and in the solid state too. Hydrogen bonding sites could be assigned and relevant aggregate models could be built. Molecular modelling allowed obtaining good estimates for hydrogen bond lengths and angles and visualisation of the geometric arrangements even of extended networks also became feasible.

Tailoring Oxygen Sensitivity with Halide Substitution in Difluoroboron Dibenzoylmethane Polylactide Materials

PubMed Central

DeRosa, Christopher A.; Kerr, Caroline; Fan, Ziyi; Kolpaczynska, Milena; Mathew, Alexander S.; Evans, Ruffin E.; Zhang, Guoqing; Fraser, Cassandra L.

2015-01-01

The dual-emissive properties of solid-state difluoroboron β-diketonate-poly(lactic acid) (BF2bdkPLA) materials have been utilized for biological oxygen sensing. In this work, BF2dbm(X)PLA materials were synthesized, where X = H, F, Cl, Br, and I. The effects of changing the halide substituent and PLA polymer chain length on the optical properties in dilute CH2Cl2 solutions and solid-state polymer films were studied. These luminescent materials show fluorescence, phosphorescence, and lifetime tunability on the basis of molecular weight, as well as lifetime modulation via the halide substituent. Short BF2dbm(Br)PLA (6.0 kDa) and both short and long BF2dbm(I)PLA polymers (6.0 or 20.3 kDa) have fluorescence and intense phosphorescence ideal for ratiometric oxygen sensing. The lighter halide-dye polymers with hydrogen, fluorine, and chlorine substitution have longer phosphorescence lifetimes and can be utilized as ultrasensitive oxygen sensors. Photostability was also analyzed for the polymer films. PMID:26480236

Structural and magnetically enhanced ferroelectric properties of Nd3+ and Fe3+ substituted Pb(Zr0.45Ti0.55)O3 ceramics

NASA Astrophysics Data System (ADS)

Kaur, Randeep; Singh, Anupinder

2018-05-01

The influence of Nd3+ and Fe3+ substitution on Pb(Zr0.45Ti0.55)O3 composition prepared via solid state reaction route have been studied. The structural evolution was investigated using an X-ray diffraction (XRD). Non perovskite Pb2Ti2O7, ZrO2 and PbO phases were observed along with the rhombohedral phase. The SEM micrograph shows the surface morphology of the samples. The density of the sample was calculated by using Archimedes principle and found to be 8.45g/cm3. The magnetic data depicts the presence of both the ferromagnetic as well as antiferromagnetic character in the solid solution. In ferroelectric studies, the values of remnant polarization (Pr) and coercive field (Ec) enhanced from 2.60 μC/cm2 - 3.44 µC/cm2 and 15.82kV/cm - 22.91kV/cm respectively.

Efficient Syntheses of Novel Fluoro-Substituted Pentacenes and Azapentacenes: Molecular and Solid-State Properties.

PubMed

Schwaben, Jonas; Münster, Niels; Klues, Michael; Breuer, Tobias; Hofmann, Philipp; Harms, Klaus; Witte, Gregor; Koert, Ulrich

2015-09-21

Non-symmetrical 6,13-disubstituted pentacenes bearing trifluoromethyl and aryl substituents have been synthesized starting from pentacenequinone. Diazapentacenes with a variety of fluorine substituents were prepared either via a Hartwig-Buchwald aryl amination route or by a SNAr strategy. As a result of a non-symmetric substitution pattern containing electron-donating substituents in combination with electron-accepting fluorine substituents, the synthesized compounds feature distinct molecular dipoles. All compounds are analyzed regarding their optoelectronic properties in solution with special focus on the frontier orbital energies as well as their molecular packing in the crystal structures. The analyses of isolated molecules are complemented by thin-film studies to examine their solid-state properties. A precise comparison between these and the molecular properties gave detailed insights into the exciton binding energies of these compounds, which are explained by means of a simple model considering the molecular packing and polarizabilities. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Arylethynyl Substituted 9,lO-Anthraquinones: Tunable Stokes Shifts by Substitution and Solvent Polarity

NASA Technical Reports Server (NTRS)

Yang, Jinhua; Dass, Amala; Rawashdeh, Abdel-Monem M.; Sotiriou-Leventis, Chariklia; Panzner, Matthew J.; Tyson, Daniel S.; Kinder, James D.; Leventis, Nicholas

2004-01-01

2-Arylethynyl- and 2,6- and 2,7-diarylethynyl-substituted 9,lO-anthraquinones were synthesized via Sonogashira coupling reactions of 2-bromo-, 2,6-dibromo-, and 2,7-dibromo-9,10- anthraquinone with para-substituted phenylacetylenes. While the redox properties of those compounds are almost insensitive to substitution, their absorption maxima are linearly related to the Hammett constants with different slopes for electron donors and electron acceptors. ABI compounds are photoluminescent both in solution (quantum yields of emission <= 6 %), and as solids. The emission spectra have the characteristics of charge-transfer bands with large Stokes shifts (100-250 nm). The charge-transfer character of the emitting state is supported by large dipole moment differences between the ground and the excited state as concluded on the basis of molecular modeling and Lippert-Mataga correlations of the Stokes shifts with solvent polarity. Maximum Stokes shifts are attained by both electron-donating and -withdrawing groups. This is explained by a destabilization of the HOMO by electron donors and a stabilization of the LUMO by electron acceptors. X-ray crystallographic analysis of, for example, 2,7-bisphenylethynfl- 9,lO-anthraquinone reveals a monoclinic P21In space group and no indication for pi-overlap that would promote quenching, thus explaining emission from the solid state. Representative reduced forms of the title compounds were isolated as stable acetates of the corresponding dihydrs-9,10- anthraquinones. The emission of these compounds is blue-shifted relative to the parent oxidized forms and is attributed to internal transitions in the dihydro-9,lO-anthraquinone core.

Monoclinic structure of hydroxylpyromorphite Pb10(PO4)6(OH)2 - hydroxylmimetite Pb10(AsO4)6(OH)2 solid solution series

NASA Astrophysics Data System (ADS)

Giera, Alicja; Manecki, Maciej; Borkiewicz, Olaf; Zelek, Sylwia; Rakovan, John; Bajda, Tomasz; Marchlewski, Tomasz

2016-04-01

Seven samples of hydroxyl analogues of pyromorphite-mimetite solid solutions series were synthesized from aqueous solutions at 80° C in a computer-controlled chemistate: 200 mL aqueous solutions of 0.05M Pb(NO3)2 and 0.03M KH2AsO4 and/or KH2PO4 were dosed with a 0.25 mL/min rate to a glass beaker, which initially contained 100 mL of distilled water. Constant pH of 8 was maintained using 2M KOH. The syntheses yielded homogeneous fine-grained white precipitates composition of which was close to theoretical Pb10[(PO4)6-x(AsO4)x](OH)2, where x = 0, 1, 2, 3, 4, 5, 6. High-resolution powder X-ray diffraction data were obtained in transmission geometry at the beamline 11-BM at the Advanced Photon Source (Argonne National Laboratory in Illinois, USA). The structure Rietveld refinements based on starting parameters of either hexagonal hydroxylpyromorphite or monoclinic mimetite-M were performed using GSAS+EXPGUI software. Apatite usually crystallizes in the hexagonal crystal system with the space group P63/m. For the first time, however, the lowering of the hexagonal to monoclinic crystal symmetry was observed in the hydroxyl variety of pyromorphite-mimetite solid solution series. This is indicated by better fitting of the modeled monoclinic structure to the experimental data. The same is not the case for analogous calcium hydroxylapatite series Ca5(PO4)3OH - Ca5(AsO4)3OH (Lee et al. 2009). Systematical linear increase of unit cell parameters is observed with As substitution from a=9.88, b=19.75, and c=7.43 for Pb10(PO4)6(OH)2 to a=10.23, b=20.32, and c=7.51 for Pb10(AsO4)6(OH)2. A strong pseudohexagonal character (γ ≈ 120° and b ≈ 2a) of the analyzed monoclinic phases was established. This work is partially funded by AGH research grant no 11.11.140.319 and partially by Polish NCN grant No 2011/01/M/ST10/06999. Lee Y.J., Stephens P.W., Tang Y., Li W., Philips B.L., Parise J.B., Reeder R.J., 2009. Arsenate substitution in hydroxylapatite: Structural characterization of the Ca5(PxAs1-xO4)3OH solid solution. American Mineralogist, 94, 666-675.

Solid-phase extraction using bis(indolyl)methane-modified silica reinforced with multiwalled carbon nanotubes for the simultaneous determination of flavonoids and aromatic organic acid preservatives.

PubMed

Wang, Na; Liao, Yuan; Wang, Jiamin; Tang, Sheng; Shao, Shijun

2015-12-01

A novel bis(indolyl)methane-modified silica reinforced with multiwalled carbon nanotubes sorbent for solid-phase extraction was designed and synthesized by chemical immobilization of nitro-substituted 3,3'-bis(indolyl)methane on silica modified with multiwalled carbon nanotubes. Coupled with high-performance liquid chromatography analysis, the extraction properties of the sorbent were evaluated for flavonoids and aromatic organic acid compounds. Under optimum conditions, the sorbent can simultaneously extract five flavonoids and two aromatic organic acid preservatives in aqueous solutions in a single-step solid-phase extraction procedure. Wide linear ranges were obtained with correlation coefficients (R(2) ) ranging from 0.9843 to 0.9976, and the limits of detection were in the range of 0.5-5 μg/L for the compounds tested. Compared with the silica modified with multiwalled carbon nanotubes sorbent and the nitro-substituted 3,3'-bis(indolyl)methane-modified silica sorbent, the developed sorbent exhibited higher extraction efficiency toward the selected analytes. The synergistic effect of nitro-substituted 3,3'-bis(indolyl)methane and multiwalled carbon nanotubes not only improved the surface-to-volume ratio but also enhanced multiple intermolecular interactions, such as hydrogen bonds, π-π, and hydrophobic interactions, between the new sorbent and the selected analytes. The as-established solid-phase extraction with high-performance liquid chromatography and diode array detection method was successfully applied to the simultaneous determination of flavonoids and aromatic organic acid preservatives in grape juices with recoveries ranging from 83.9 to 112% for all the selected analytes. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Singlet Fission and Excimer Formation in Disordered Solids of Alkyl-Substituted 1,3-Diphenylisobenzofurans.

PubMed

Dron, Paul I; Michl, Josef; Johnson, Justin C

2017-11-16

We describe the preparation and excited state dynamics of three alkyl derivatives of 1,3-diphenylisobenzofuran (1) in both solutions and thin films. The substitutions are intended to disrupt the slip-stacked packing observed in crystals of 1 while maintaining the favorable energies of singlet and triplet for singlet fission (SF). All substitutions result in films that are largely amorphous as judged by the absence of strong X-ray diffraction peaks. The films of 1 carrying a methyl in the para position of one phenyl ring undergo SF relatively efficiently (≥75% triplet yield, Φ T ) but more slowly than thin films of 1. When the methyl is replaced with a t-butyl, kinetic competition in the excited state favors excimer formation rather than SF (Φ T = 55%). When t-Bu groups are placed in both meta positions of the phenyl substituent, SF is slowed further and Φ T = 35%.

Local Variability of the Peierls Barrier of Screw Dislocations in Ta-10W.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Foiles, Stephen M.

2017-10-01

It is well know that the addition of substitutional elements changes the mechanical behavior of metals, a effect referred to solid solution hardening. For body-centered-cubic (BCC) metals, screw dislocation play a key role in the mechanical properties. Here the detailed modification of the Peierls barrier for screw dislocation motion in Ta with W substitutional atoms is computing using density functional theory (DFT). A reduced order model (ROM) of the influence of W substitution on the Peierls barrier is developed. The mean field change in the Peierls barrier for a Ta10W alloy is determined and shown to be larger than anticipatedmore » based on simple elasticity considerations. The ROM could be used in future calculations to determine the local variability of the Peierls barrier and the resultant influence on the motion of screw dislocation in this alloy.« less

Synthesis, crystal structure and ionic conductivity of the Ba3Mo1-xWxNbO8.5 solid solution

NASA Astrophysics Data System (ADS)

Bernasconi, Andrea; Tealdi, Cristina; Mühlbauer, Martin; Malavasi, Lorenzo

2018-02-01

Ba3MoNbO8.5 compound has been recently discovered as novel oxide ionic conductor with a structure that is a hybrid between 9R hexagonal perovskite and palmierite. In this work, the full substitution of Mo with W has been demonstrated as possible, without altering significantly the conductivity of the material. The crystal structure of the Ba3Mo1-xWxNbO8.5 solid solution (with x equals 0, 0.25, 0.5, 0.75 and 1) has been investigated by X-ray powder diffraction, showing a reduction of the unit cell by increasing the molybdenum content, despite the larger size of tungsten compared to molybdenum. Neutron powder diffraction measurements have been performed, indicating different levels of contribution of 9R polytype and of palmierite to the hybrid structure of the material as a function of the W-content.

The effect of the cation substitution on the structural and vibrational properties of Cs2NaGaxSc1-xF6 solid solution

NASA Astrophysics Data System (ADS)

Doriguetto, A. C.; Boschi, T. M.; Pizani, P. S.; Mascarenhas, Y. P.; Ellena, J.

2004-08-01

Raman scattering and x-ray diffration were used to characterize the structural and vibrational properties of the Cs2NaGaxSc1-xF6 solid solutions, for x ranging from 0.0 to 1.0. The Raman spectra, taken at room and low temperature, allow us to follow the phase evolution in detail and indicate the breaking of the local symmetry since low Ga concentration levels. Five compositions were studied by x-ray diffraction: x=0.0, 0.2, 0.5, 0.8, and 1.0. A cubic space group, Fm3¯m, was found to x=0.0 and x=0.2 and a trigonal one was found to x=0.5, 0.8, and 1.0. Details of both phases are presented and the correlation between x-ray diffraction and Raman scattering is discussed.

High-Temperature Thermoelectric Properties of (1 - x) SrTiO3 - ( x) La1/3NbO3 Ceramic Solid Solution

NASA Astrophysics Data System (ADS)

Srivastava, Deepanshu; Azough, F.; Molinari, M.; Parker, S. C.; Freer, R.

2015-06-01

Ceramics based on SrTiO3 are of growing interest as thermoelectric materials because of their high-temperature stability and non-toxicity. Substitution of La and Nb into the perovskite structure provides opportunities to control both the microstructure and properties. Ceramic solid solutions of (1 - x) SrTiO3 - ( x) La1/3NbO3 were prepared by the mixed oxide route, using compositional steps of x = 0.1. Pressed pellets were sintered at temperatures of 1573 K to 1723 K in air. Addition of aliovalent ions (La3+, Nb5+) on the A/B sites (Sr2+, Ti4+) led to A-Site cation deficiency in the stoichiometric compositions and other defect structures which increased carrier concentration. A maximum ZT of 0.004 was obtained for the x = 0.2 stoichiometric sample, although much higher ZT values are possible by sample reduction.

Dendrite Suppression by Synergistic Combination of Solid Polymer Electrolyte Crosslinked with Natural Terpenes and Lithium-Powder Anode for Lithium-Metal Batteries.

PubMed

Shim, Jimin; Lee, Jae Won; Bae, Ki Yoon; Kim, Hee Joong; Yoon, Woo Young; Lee, Jong-Chan

2017-05-22

Lithium-metal anode has fundamental problems concerning formation and growth of lithium dendrites, which prevents practical applications of next generation of high-capacity lithium-metal batteries. The synergistic combination of solid polymer electrolyte (SPE) crosslinked with naturally occurring terpenes and lithium-powder anode is promising solution to resolve the dendrite issues by substituting conventional liquid electrolyte/separator and lithium-foil anode system. A series of SPEs based on polysiloxane crosslinked with natural terpenes are prepared by facile thiol-ene click reaction under mild condition and the structural effect of terpene crosslinkers on electrochemical properties is studied. Lithium powder with large surface area is prepared by droplet emulsion technique (DET) and used as anode material. The effect of the physical state of electrolyte (solid/liquid) and morphology of lithium-metal anode (powder/foil) on dendrite growth behavior is systematically studied. The synergistic combination of SPE and lithium-powder anode suggests an effective solution to suppress the dendrite growth owing to the formation of a stable solid-electrolyte interface (SEI) layer and delocalized current density. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Development and Characterization of Improved NiTiPd High-Temperature Shape-Memory Alloys by Solid-Solution Strengthening and Thermomechanical Processing

NASA Technical Reports Server (NTRS)

Bigelow, Glen; Noebe, Ronald; Padula, Santo, II; Garg, Anita; Olson, David

2006-01-01

The need for compact, solid-state actuation systems for use in the aerospace, automotive, and other transportation industries is currently motivating research in high-temperature shape-memory alloys (HTSMA) with transformation temperatures greater than 100 C. One of the basic high-temperature alloys investigated to fill this need is Ni(19.5)Ti(50.5)Pd30. Initial testing has indicated that this alloy, while having acceptable work characteristics, suffers from significant permanent deformation (or ratcheting) during thermal cycling under load. In an effort to overcome this deficiency, various solid-solution alloying and thermomechanical processing schemes were investigated. Solid-solution strengthening was achieved by substituting 5at% gold or platinum for palladium in Ni(19.5)Ti(50.5)Pd30, the so-called baseline alloy, to strengthen the martensite and austenite phases against slip processes and improve thermomechanical behavior. Tensile properties, work behavior, and dimensional stability during repeated thermal cycling under load for the ternary and quaternary alloys were compared. The relative difference in yield strength between the martensite and austenite phases and the dimensional stability of the alloy were improved by the quaternary additions, while work output was only minimally impacted. The three alloys were also thermomechanically processed by cycling repeatedly through the transformation range under a constant stress. This so-called training process dramatically improved the dimensional stability in these samples and also recovered the slight decrease in work output caused by quaternary alloying. An added benefit of the solid-solution strengthening was maintenance of enhanced dimensional stability of the trained material to higher temperatures compared to the baseline alloy, providing a greater measure of over-temperature capability.

Investigations on the Crystal-Chemical Behavior of Transition-Metal-Bearing Aluminosilicate Garnet Solid Solutions Using 27Al and 29Si NMR Spectroscopy

NASA Astrophysics Data System (ADS)

Palke, A. C.; Geiger, C. A.; Stebbins, J. F.

2015-12-01

The petrological importance of silicate garnet is derived from the presence of three distinct cation sites of varying size and coordination number. This allows for a wide range of trace, minor, and major element substitutions. However, a full and precise crystal-chemical understanding of the nature of transition metals in garnet is not at hand. Possible mechanisms of various charge-balanced substitutions (e.g. octahedral Ti4+ or tetrahedral Al3+) and the structural state of solid solutions (i.e. short- to long-range ordering) need study. We report on ongoing efforts in these directions using 27Al and 29Si Magic-Angle Spinning Nuclear Magnetic Resonance (MAS-NMR) spectroscopy. Early work on synthetic and natural Fe- and Mn-bearing pyrope- and grossular-rich garnets focused on the effect these paramagnetic transition metals have in measuring and interpreting NMR spectra. These results have been expanded with NMR measurements on synthetic pyrope-rich garnets containing other paramagnetic transition metals including Cr3+, V3+, Co2+, and Ni2+ as well as diamagnetic Ti4+. NMR peaks are severely broadened in the presence of even small concentrations of Cr3+, Mn2+, and Fe3+ leading to a loss of spectral resolution. On the other hand, the spectra of garnet containing V3+, Fe2+, Co2+, and Ni2+ have better resolution and show separate paramagnetically shifted NMR peaks. In some cases, crystal-chemical information can be obtained because of the large frequency separations between the NMR peaks that can be assigned to various local atomic configurations around Al and Si. Furthermore, the 27Al NMR spectrum of a synthetic pyrope garnet with about 2% diamagnetic Ti4+ on the octahedral site showed the absence of any tetrahedral Al3+, which rules out the substitution mechanism VITi + IVAl = VIAl + IVSi in the solid solution. Our NMR investigations on garnet are now being made at the exploratory level. We think that NMR spectra of diamagnetic garnet can provide information on a number of crystal-chemical properties. Spectra of garnet containing various paramagnetic transition elements can also, in some cases, give local structural information. With a better understanding of paramagnetic effects in NMR spectroscopy, this type of study can possibly be expanded to other geologically important paramagnetic minerals and phases.

Phase equilibria and crystal chemistry of the CaO–½Sm 2O 3–CoOz system at 885 °C in air

DOE PAGES

Wong-Ng, W.; Laws, W.; Lapidus, S. H.; ...

2015-06-27

The CaO–½Sm 2O 3–CoOz system prepared at 885 °C in air consists of two calcium cobaltate compounds, namely, the 2D thermoelectric oxide solid solution, (Ca 3$-$xSm x)Co 4O 9$-$z (0 ≤ x ≤ 0.5) which has a misfit layered structure, and the 1D Ca 3Co 2O 6 which consists of chains of alternating CoO 6 trigonal prisms and CoO 6 octahedra. Ca 3Co 2O 6 was found to be a point compound without the substitution of Sm on the Ca site. A solid solution region of distorted perovskite, (Sm 1$-$xCa x)CoO 3$-$z (0 ≤ x ≤ 0.22, space group Pnma)more » was established. The reported Sm 2CoO 4 phase was not observed at 885 °C, but a ternary Ca-doped oxide, (Sm 1+xCa 1$-$x)CoO 4$-$z (Bmab) where 0 < x ≤ 0.15 was found to be stable at this temperature. In the peripheral binary systems, Sm was not present in the Ca site of CaO, while a small solid solution region was identified for (Sm 1$-$xCa x)O(3 $-$z)/2 (0 ≤ x ≤ 0.075). Lastly, ten solid solution tie-line regions and six three-phase regions were determined in the CaO–½Sm 2O 3–CoO z system in air.« less

Renierite, Cu10ZnGe2Fe4S16-Cu11GeAsFe4S16: a coupled solid solution series.

USGS Publications Warehouse

Bernstein, L.R.

1986-01-01

The composition of renierite is found to be Cu10(Zn1-xCux)Ge2-xAsxFe4S16 (0 = or < x = or < 1), with continuous solid solution between the zincian and arsenian end-members, Cu10ZnGe2Fe4S16 and Cu11GeAsFe4S16, through the coupled substitution Zn(II) + Ge(IV) = Cu(I) + As(V). This is the first reported example of extensive coupled solid solution in a sulphide mineral. Arsenian renierite, not previously characterized, is similar to zincian renierite in polished section, with a slightly redder colour and lower anisotropy. It is reddish orange with relief very similar to that of bornite, though it is harder (VHN25 = 286) and does not tarnish in air. It is slightly bireflective, with colours varying from orange-yellow to reddish orange in nearly crossed polarizers. The strongest powder XRD lines are: 3.042(100), 1.861(29), 1.869(16), 1.594(11) and 1.017(10) A; D(calc.) 4.50 g/cm3. Specimens have been found at the Ruby Creek copper deposit, Alaska, where zincian renierite also occurs, and at the Inexco no. 1 mine, Jamestown, Colorado.-J.A.Z.

Disappearance of superconductivity in the solid solution between (Ca4Al2O6)(Fe2As2) and (Ca4Al2O6)(Fe2P2) superconductors.

PubMed

Shirage, Parasharam M; Kihou, Kunihiro; Lee, Chul-Ho; Takeshita, Nao; Eisaki, Hiroshi; Iyo, Akira

2012-09-19

The effect of alloying the two perovskite-type iron-based superconductors (Ca(4)Al(2)O(6))(Fe(2)As(2)) and (Ca(4)Al(2)O(6))(Fe(2)P(2)) was examined. While the two stoichiometric compounds possess relatively high T(c)'s of 28 and 17 K, respectively, their solid solutions of the form (Ca(4)Al(2)O(6))(Fe(2)(As(1-x)P(x))(2)) do not show superconductivity over a wide range from x = 0.50 to 0.95. The resultant phase diagram is thus completely different from those of other typical iron-based superconductors such as BaFe(2)(As,P)(2) and LaFe(As,P)O, in which superconductivity shows up when P is substituted for As in the non-superconducting "parent" compounds. Notably, the solid solutions in the non-superconducting range exhibit resistivity anomalies at temperatures of 50-100 K. The behavior is reminiscent of the resistivity kink commonly observed in various non-superconducting parent compounds that signals the onset of antiferromagnetic/orthorhombic long-range order. The similarity suggests that the suppression of the superconductivity in the present case also has a magnetic and/or structural origin.

Local structural relaxation around Co2+ along the hardystonite-Co-åkermanite melilite solid solution

NASA Astrophysics Data System (ADS)

Ardit, Matteo; Cruciani, Giuseppe; Dondi, Michele

2012-10-01

Six pure compounds belonging to the hardystonite (Ca2ZnSi2O7)-Co-åkermanite (Ca2CoSi2O7) solid solution were investigated by the combined application of X-ray powder diffraction and electronic absorption spectroscopy. Structural refinements of the XRPD data revealed a negative excess volume of mixing due to the single isovalent substitution of Co for Zn in the tetrahedral site. In agreement with the diffraction data, deconvolution of the optical spectra showed a progressive decreasing of the crystal field strength parameter 10 Dq moving toward the Co-åkermanite end-member, meaning that the local cobalt-oxygen bond distance, < {{Co}}{-}{{O}}rangle^{{local}} , increased along the join with the amount of cobalt. The calculated structural relaxation coefficient around the fourfold coordinated Co2+ in the Ca2(Zn1- x Co x )Si2O7 join was ɛ = 0.69, very far from the one predicted by the Vegard's law ( ɛ = 0) and at variance with ɛ = 0.47 previously found for tetrahedrally coordinated Co2+ in gahnite-Co-aluminate spinel solid solution. This difference is consistent with the largest constraints existing on the spinel structure, based on cubic closest packing, compared to the more flexible layered melilite structure.

Scanning tunneling spectroscopy of the surface states of Dirac fermions in thermoelectrics based on bismuth telluride

NASA Astrophysics Data System (ADS)

Lukyanova, L. N.; Makarenko, I. V.; Usov, O. A.; Dementev, P. A.

2018-05-01

The morphology of the interlayer van der Waals surface and differential tunneling conductance in p-Bi2‑xSbxTe3‑ySey solid solutions were studied by scanning tunneling microscopy and spectroscopy in dependence on compositions. The topological characteristics of the Dirac fermion surface states were determined. It was shown that the thermoelectric power factor and the material parameter enhance with the shift of the Dirac point to the top of the valence band with the increasing of atomic substitution in these thermoelectrics. A correlation between topological characteristics, power factor and material parameters was found. A growth contribution of the surface states is determined by an increase of the Fermi velocity for large atomic substitutions of Bi at x > 1.5 and small substitutions in the Te sublattice (y = 0.06). In compositions with smaller substitutions at x = (1–1.3) and y = (0.06–0.09), similar effect of the surface states is determined by raising the surface concentration of charge carriers.

Subcontract Report: Diffusion Mechanisms and Bond Dynamics in Solid Electrolyte Ion-Conductors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zevgolis, A.; Hall, A.; Alvez, T.

2017-10-03

We employ first-principles molecular dynamics simulations and Maximally Localized Wannier Function (MLWF) analysis to explore how halide substitution and nano-phase microstructures affect diffusivity, through the activation energy barrier - E a and D 0, in the solid electrolyte Li 3InBr 6-xCl x. We find that nano-phase microstructures with x=3 (50-50 Br-Cl) mixed composition have a higher diffusivity compared to x=2 and x=3 solid solutions. There is a positive linear relationship between ln(D 0.) and E a, which suggests that for superionic conductivity optimizing both the activation energy and the D 0 is important. Bond frustration due to mismatch in crystalmore » geometry and ideal coordination number leads to especially high diffusivity through a high D 0 in the x=3 composition.« less

La-Sr-Ni-Co-O based perovskite-type solid solutions as catalyst precursors in the CO 2 reforming of methane

NASA Astrophysics Data System (ADS)

Valderrama, Gustavo; Kiennemann, Alain; Goldwasser, Mireya R.

La 1- xSr xNi 0.4Co 0.6O 3 and La 0.8Sr 0.2Ni 1- yCo yO 3 solid solutions with perovskite-type structure were synthesized by the sol-gel resin method and used as catalytic precursors in the dry reforming of methane with CO 2 to syngas, between 873 and 1073 K at atmospheric pressure under continuous flow of reactant gases with CH 4/CO 2 = 1 ratio. These quaternary oxides were characterized by X-ray diffraction (XRD), BET specific surface area and temperature-programmed reduction (TPR) techniques. XRD analyses of the more intense diffraction peaks and cell parameter measurements showed formation of La-Sr-Ni-Co-O solid solutions with La 0.9Sr 0.1CoO 3 and/or La 0.9Sr 0.1NiO 3 as the main crystallographic phases present on the solids depending on the degree of substitution. TPR analyses showed that Sr doping decreases the temperature of reduction via formation of intermediary species producing Ni 0, Co 0 with particle sizes in the range of nanometers over the SrO and La 2O 3 phases. These metallic nano particles highly dispersed in the solid matrix are responsible for the high activity shown during the reaction and avoid carbon formation. The presence of Sr in doping quantities also promotes the secondary reactions of carbon formation and water-gas shift in a very small extension during the dry reforming reaction.

Solid oral forms availability in children: a cost saving investigation

PubMed Central

Lajoinie, Audrey; Henin, Emilie; Kassai, Behrouz; Terry, David

2014-01-01

Aim To assess the suitability and potential cost savings, from both the hospital and community perspective, of prescribed oral liquid medicine substitution with acceptable solid forms for children over 2 years. Method Oral liquid medicines dispensed from a paediatric hospital (UK) in 1 week were assessed by screening for existence of the solid form alternative and evaluating the acceptability of the available solid form, firstly related to the prescribed dose and secondly to acceptable size depending on the child's age. Costs were calculated based on providing treatment for 28 days or prescribed duration for short term treatments. Results Over 90% (440/476) of liquid formulations were available as a marketed solid form. Considering dosage acceptability (maximum of 10% deviation from prescribed dosage or 0% for narrow therapeutic range drugs, maximum tablet divisions into quarters) 80% of liquids could be substituted with a solid form. The main limitation for liquid substitution would be solid form size. However, two-thirds of prescribed liquids could have been substituted with a suitable solid form for dosage and size, with estimated savings being of £5K and £8K in 1 week, respectively based on hospital and community costs, corresponding to a projected annual saving of £238K and £410K (single institution). Conclusion Whilst not all children over 2 years will be able to swallow tablets, drug cost savings if oral liquid formulations were substituted with suitable solid dosage forms would be considerable. Given the numerous advantages of solid forms compared with liquids, this study may provide a theoretical basis for investing in supporting children to swallow tablets/capsules. PMID:24965935

Physicochemical and sensory characteristics of soy sauce substituted with pigeon pea (Cajanus cajan (Linn.))

NASA Astrophysics Data System (ADS)

Retnaningsih, C.; Sumardi; Meiliana; Surya, A.

2018-01-01

The objective of this study wasto investigate the physicochemical and sensory properties of the soy sauce substituted with pigeon pea. Soybean was substituted by 20%, 50%, 75%, and 100% of pigeon pea. The observation included viscosity, total solids, protein levels, antioxidant activity, and sensory characteristics. The results showed that the more substitution of pigeon pea, the less the protein content of soy sauce and the more the antioxidant activity as well as total solids. The most favored group was 25% pigeon pea substitution. It is suggested that soy sauce could be prepared using 25% to 75% pigeon pea substitution.

Band Structure Engineering by Substitutional Doping in Solid-State Solutions of [5-Me-PLY(O,O)]2B(1-x)Be(x) Radical Crystals.

PubMed

Bag, Pradip; Itkis, Mikhail E; Stekovic, Dejan; Pal, Sushanta K; Tham, Fook S; Haddon, Robert C

2015-08-12

We report the substitutional doping of solid-state spiro-bis(5-methyl-1,9-oxido-phenalenyl)boron radical ([2]2B) by co-crystallization of this radical with the corresponding spiro-bis(5-methyl-1,9-oxido-phenalenyl)beryllium compound ([2]2Be). The pure compounds crystallize in different space groups ([2]2B, P1̅, Z = 2; [2]2Be, P2₁/c, Z = 4) with distinct packing arrangements, yet we are able to isolate crystals of composition [2]2B(1-x)Be(x), where x = 0-0.59. The phase transition from the P1̅ to the P2₁/c space group occurs at x = 0.1, but the conductivities of the solid solutions are enhanced and the activation energies reduced for values of x = 0-0.25. The molecular packing is driven by the relative concentration of the spin-bearing ([2]2B) and spin-free ([2]2Be) molecules in the crystals, and the extended Hückel theory band structures show that the progressive incorporation of spin-free [2]2Be in the lattice of the [2]2B radical (overall bandwidth, W = 1.4 eV, in the pure compound) leads to very strong narrowing of the bandwidth, which reaches a minimum at [2]2Be (W = 0.3 eV). The results provide a graphic picture of the structural transformations undergone by the lattice, and at certain compositions we are able to identify distinct structures for the [2]2B and [2]2Be molecules in a single crystalline phase.

HIGH DENSITY NUCLEAR FUEL COMPOSITION

DOEpatents

Litton, F.B.

1962-07-17

ABS>A nuclear fuel consisting essentially of uranium monocarbide and containing 2.2 to 4.6 wt% carbon, 0.1 to 2.3 wt% oxygen, 0.05 to 2.5 wt% nitrogen, and the balance uranium was developed. The maximum oxygen content was less than one-half the carbon content by weight and the carbon, oxygen, and nitrogen are present as a single phase substituted solid solution of UC, C, O, and N. A method of preparing the fuel composition is described. (AEC)

Effect of Pd substitution for Ni on magnetism in UNiAl

NASA Astrophysics Data System (ADS)

Dremov, R. V.; Andreev, A. V.; Šebek, J.; Mushnikov, N. V.; Goto, T.; Havela, L.; Sechovský, V.; Shiokawa, Y.; Homma, Y.

1999-01-01

Itinerant 5f-electron antiferromagnet UNiAl ( TN=19.3 K) undergoes a metamagnetic transition in fields ( Bc≈11 T) applied along the c-axis of the hexagonal ZrNiAl-type structure. The same structure is preserved in the UNi 1- xPd xAl solid solutions x⩽0.4 characterized by isotropic lattice expansion with increasing x. The gradual increase of Bc and TN due to the Pd doping can be tentatively attributed to enhancement of antiferromagnetic exchange interactions.

Sr-containing hydroxyapatite: morphologies of HA crystals and bioactivity on osteoblast cells.

PubMed

Aina, Valentina; Bergandi, Loredana; Lusvardi, Gigliola; Malavasi, Gianluca; Imrie, Flora E; Gibson, Iain R; Cerrato, Giuseppina; Ghigo, Dario

2013-04-01

A series of Sr-substituted hydroxyapatites (HA), of general formula Ca(10-x)Srx(PO4)6(OH)2, where x=2 and 4, were synthesized by solid state methods and characterized extensively. The reactivity of these materials in cell culture medium was evaluated, and the behavior towards MG-63 osteoblast cells (in terms of cytotoxicity and proliferation assays) was studied. Future in vivo studies will give further insights into the behavior of the materials. A paper by Lagergren et al. (1975), concerning Sr-substituted HA prepared by a solid state method, reports that the presence of Sr in the apatite composition strongly influences the apatite diffraction patterns. Zeglinsky et al. (2012) investigated Sr-substituted HA by ab initio methods and Rietveld analyses and reported changes in the HA unit cell volume and shape due to the Sr addition. To further clarify the role played by the addition of Sr on the physico-chemical properties of these materials we prepared Sr-substituted HA compositions by a solid state method, using different reagents, thermal treatments and a multi-technique approach. Our results indicated that the introduction of Sr at the levels considered here does influence the structure of HA. There is also evidence of a decrease in the crystallinity degree of the materials upon Sr addition. The introduction of increasing amounts of Sr into the HA composition causes a decrease in the specific surface area and an enrichment of Sr-apatite phase at the surface of the samples. Bioactivity tests show that the presence of Sr causes changes in particle size and/or morphology during soaking in MEM solution; on the contrary the morphology of pure HA does not change after 14 days of reaction. The presence of Sr, as Sr-substituted HA and SrCl2, in cultures of human MG-63 osteoblasts did not produce any cytotoxic effect. In fact, Sr-substituted HA increased the proliferation of osteoblast cells and enhanced cell differentiation: Sr in HA has a positive effect on MG-63 cells. In contrast, Sr ions alone, at the concentrations released by Sr-HA (1.21-3.24 ppm), influenced neither cell proliferation nor differentiation. Thus the positive effects of Sr in Sr-HA materials are probably due to the co-action of other ions such as Ca and P. Copyright © 2012 Elsevier B.V. All rights reserved.

Preparation and characterization of fusion processed solid dispersions containing a viscous thermally labile polymeric carrier.

PubMed

Hughey, Justin R; Keen, Justin M; Miller, Dave A; Brough, Chris; McGinity, James W

2012-11-15

The primary aim of the present study was to investigate the ability of hydroxypropyl and methoxyl substituted cellulose ethers to stabilize supersaturated concentrations of itraconazole (ITZ), a poorly water-soluble weak base, after an acid-to-neutral pH transition. A secondary aim of the study was to evaluate the effect of fusion processes on polymer stability and molecular weight. Polymer screening studies showed that stabilization of ITZ supersaturation was related to the molecular weight of the polymer and levels of hydroxypropyl and methoxyl substitution. METHOCEL E50LV (E50LV), which is characterized as having a high melt viscosity, was selected for solid dispersion formulation studies. Hot-melt extrusion processing of E50LV based compositions resulted in high torque loads, low material throughput and polymer degradation. KinetiSol Dispersing, a novel fusion based processing technique, was evaluated as a method to prepare the solid dispersions with reduced levels of polymer degradation. An experimental design revealed that polymer molecular weight was sensitive to shearing forces and high temperatures. However, optimal processing conditions resulted in significantly reduced E50LV degradation relative to HME processing. The technique was effectively utilized to prepare homogenous solid solutions of E50LV and ITZ, characterized as having a single glass transition temperature over a wide range of drug loadings. All prepared compositions provided for a high degree of ITZ supersaturation stabilization. Copyright © 2012 Elsevier B.V. All rights reserved.

Structural, chemical and optical evaluation of Cu-doped ZnO nanoparticles synthesized by an aqueous solution method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Iribarren, A., E-mail: augusto@imre.oc.uh.cu; Hernández-Rodríguez, E.; Maqueira, L.

Highlights: • Cu-doped ZnO nanoparticles obtained by chemical synthesis. • Substitutional or interstitial Cu into ZnO lead specific structural, chemical, and optical changes. • Incorporation efficiency of Cu atoms in ZnO as a function of the Cu concentration in the precursor dissolution. - Abstract: In this work a study of ZnO and Cu-doped ZnO nanoparticles obtained by chemical synthesis in aqueous media was carried out. Structural analysis gave the dominant presence of wurtzite ZnO phase forming a solid solution Zn{sub 1−x}Cu{sub x}O. For high Cu doping CuO phase is also present. For low Cu concentration the lattice shrinks due tomore » Cu atoms substitute Zn atoms. For high Cu concentration the lattice enlarges due to predominance of interstitial Cu. From elemental analysis we determined and analyzed the incorporation efficiency of Cu atoms in Zn{sub 1−x}Cu{sub x}O as a function of the Cu concentration in the precursor dissolution. Combining structural and chemical results we described the Cu/Zn precursor concentrations r{sub w} in which the solid solution of Cu in ZnO is predominant. In the region located at r{sub w} ≈ 0.2–0.3 it is no longer valid. For Cu/Zn precursor concentration r{sub w} > 0.3 interstitial Cu dominates, and some amount of copper oxide appears. As the Cu concentration increases, the effective size of nanoparticles decreases. Photoluminescence (PL) measurements of the Cu-doped ZnO nanoparticles were carried out and analyzed.« less

Stabilization of Polar Nanoregions in Pb-free Ferroelectrics

DOE PAGES

Pramanick, A.; Dmowski, Wojciech; Egami, Takeshi; ...

2018-05-18

In this study, the formation of polar nanoregions through solid-solution additions is known to enhance significantly the functional properties of ferroelectric materials. Despite considerable progress in characterizing the microscopic behavior of polar nanoregions (PNR), understanding their real-space atomic structure and dynamics of their formation remains a considerable challenge. Here, using the method of dynamic pair distribution function, we provide direct insights into the role of solid-solution additions towards the stabilization of polar nanoregions in the Pb-free ferroelectric of Ba(Zr,Ti)O 3. It is shown that for an optimum level of substitution of Ti by larger Zr ions, the dynamics of atomicmore » displacements for ferroelectric polarization are slowed sufficiently below THz frequencies, which leads to increased local correlation among dipoles within PNRs. The dynamic pair distribution function technique demonstrates a unique capability to obtain insights into locally correlated atomic dynamics in disordered materials, including new Pb-free ferroelectrics, which is necessary to understand and control their functional properties.« less

Stabilization of Polar Nanoregions in Pb-free Ferroelectrics

NASA Astrophysics Data System (ADS)

Pramanick, A.; Dmowski, W.; Egami, T.; Budisuharto, A. Setiadi; Weyland, F.; Novak, N.; Christianson, A. D.; Borreguero, J. M.; Abernathy, D. L.; Jørgensen, M. R. V.

2018-05-01

The formation of polar nanoregions through solid-solution additions is known to enhance significantly the functional properties of ferroelectric materials. Despite considerable progress in characterizing the microscopic behavior of polar nanoregions (PNR), understanding their real-space atomic structure and dynamics of their formation remains a considerable challenge. Here, using the method of dynamic pair distribution function, we provide direct insights into the role of solid-solution additions towards the stabilization of polar nanoregions in the Pb-free ferroelectric of Ba (Zr ,Ti )O3 . It is shown that for an optimum level of substitution of Ti by larger Zr ions, the dynamics of atomic displacements for ferroelectric polarization are slowed sufficiently below THz frequencies, which leads to increased local correlation among dipoles within PNRs. The dynamic pair distribution function technique demonstrates a unique capability to obtain insights into locally correlated atomic dynamics in disordered materials, including new Pb-free ferroelectrics, which is necessary to understand and control their functional properties.

Stabilization of Polar Nanoregions in Pb-free Ferroelectrics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pramanick, A.; Dmowski, Wojciech; Egami, Takeshi

In this study, the formation of polar nanoregions through solid-solution additions is known to enhance significantly the functional properties of ferroelectric materials. Despite considerable progress in characterizing the microscopic behavior of polar nanoregions (PNR), understanding their real-space atomic structure and dynamics of their formation remains a considerable challenge. Here, using the method of dynamic pair distribution function, we provide direct insights into the role of solid-solution additions towards the stabilization of polar nanoregions in the Pb-free ferroelectric of Ba(Zr,Ti)O 3. It is shown that for an optimum level of substitution of Ti by larger Zr ions, the dynamics of atomicmore » displacements for ferroelectric polarization are slowed sufficiently below THz frequencies, which leads to increased local correlation among dipoles within PNRs. The dynamic pair distribution function technique demonstrates a unique capability to obtain insights into locally correlated atomic dynamics in disordered materials, including new Pb-free ferroelectrics, which is necessary to understand and control their functional properties.« less

Role of salt concentration in blend polymer for energy storage conversion devices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arya, Anil; Sharma, A. L., E-mail: alsharmaiitkgp@gmail.com; Sadiq, M.

2016-05-06

Solid Polymer Electrolytes (SPE) are materials of considerable interest worldwide, which serves dual purpose of electrolyte and separator between electrode compartments in renewable energy conversion/storage devices such as; high energy density batteries, electrochromic display devices, and supercapacitors. Polymer blend electrolytes are prepared for various concentration of salt (Ö/Li) with the constant ratio (0.5 gm) of each PEO and PAN polymers (blend polymer) using solution casting technique. Solid polymeric ionic conductor as a separator is the ultimate substitute to eliminate the drawback related to liquid and gel polymer ionic conductors. In the present work, solid polymer electrolyte film consisting of PEO,more » PAN and LiPF{sub 6} are examined for various concentration of lithium salt by keeping PEO/PAN blend ratio as a constant with a view to optimize the dominant salt concentration which could give the maximum conductivity at ambient temperature.« less

Structural analysis of pyridine-imino boronic esters involving secondary interactions on solid state

NASA Astrophysics Data System (ADS)

Sánchez-Portillo, Paola; Arenaza-Corona, Antonino; Hernández-Ahuactzi, Irán F.; Barba, Victor

2017-04-01

Twelve boronic esters (1a-1l) synthesized from 4-halo- substituted arylboronic acids (halo = F, Cl, Br, I and CF3) with 2-amino-2- alkyl (H, Me) -1,3-propanediol in presence of (3- or 4)-pyridine carboxaldehyde are described. A solvent mixture toluene/methanol 1:4 ratio was used. All compounds include both donor/acceptor functional groups, which are the necessary elements to self-assembly of the molecular species. Several secondary interactions as I⋯N, Br⋯Br, Br⋯B, F⋯B, Csbnd H⋯N, Csbnd H⋯O, Br⋯π and Csbnd H⋯π support the 1D and 2D polymeric frameworks in solid state. The coordination of the nitrogen atom from the pyridine moiety with the boron atom was not observed in either solution or solid state.

di Synthesis and Characterization of the Platinum-Substituted Keggin Anion alpha-H2SiPtW11O404-

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klonowski, P; Goloboy, JC; Uribe-Romo, FJ

2014-12-15

Acidification of an aqueous solution of K8SiW11O39 and K2Pt(OH)(6) to pH 4 followed by addition of excess tetramethylammonium (TMA) chloride yielded a solid mixture of TMA salts of H2SiPtW11O404- (1) and SiW12O404- (2). The former was separated from the latter by extraction into an aqueous solution and converted into tetra-n-butylammonium (TBA) and potassium salts TBA-1 and K-1. The a-H2SiPtW11O404- was identified as a monosubstituted Keggin anion using elemental analysis, IR spectroscopy, X-ray crystallography, electrospray ionization mass spectrometry, Pt-195 NMR spectroscopy, (183)W NMR spectroscopy, and W-183-W-183 2D INADEQUATE NMR spectroscopy. Both TBA-1 and K-1 readily cocrystallized with their unsubstituted Keggin anionmore » salts, TBA-2 and K-2, respectively, providing an explanation for the historical difficulty of isolating certain platinum-substituted heteropolyanions in pure form.« less

Interfacial Microstructure and Its Influence on Resistivity of Thin Layers Copper Cladding Steel Wires

NASA Astrophysics Data System (ADS)

Li, Hongjuan; Ding, Zhimin; Zhao, Ruirong

2018-04-01

The interfacial microstructure and resistivity of cold-drawn and annealed thin layers copper cladding steel (CCS) wires have been systematically investigated by the methods of scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS), and resistivity testing. The results showed that the Cu and Fe atoms near interface diffused into each other matrixes. The Fe atoms diffused into Cu matrixes and formed a solid solution. The mechanism of solid solution is of substitution type. When the quantity of Fe atoms exceeds the maximum solubility, the supersaturated solid solution would form Fe clusters and decompose into base Cu and α-Fe precipitated phases under certain conditions. A few of α-Fe precipitates was observed in the copper near Cu/Fe interfaces of cold-drawn CCS wires, with 1-5 nm in size. A number of α-Fe precipitates of 1-20 nm in size can be detected in copper near Cu/Fe interfaces of CCS wires annealed at 850°C. When annealing temperature was less than 750°C, the resistivity of CCS wires annealed was lower than that of cold-drawn CCS wires. However, when annealing temperature was above 750°C, the resistivity of CCS wires was greater than that of cold-drawn CCS wires and increased with rising the annealing temperature. The relationship between nanoscale α-Fe precipitation and resistivity of CCS wires has been well discussed.

New Insight into Phase Formation of MxMg2Al4+xSi5−xO18:Eu2+ Solid Solution Phosphors and Its Luminescence Properties

PubMed Central

Zhou, Jun; Xia, Zhiguo; Chen, Mingyue; Molokeev, Maxim S.; Liu, Quanlin

2015-01-01

Here we reported the phase formation of MxMg2Al4+xSi5−xO18:Eu2+ (M = K, Rb) solid solution phosphors, where M+ ions were introduced into the void channels of Mg2Al4Si5O18 via Al3+/Si4+ substitution to keep the charge balance. XRD results revealed that the as-prepared phosphors with different M+ contents were iso-structural with Mg2Al4Si5O18 phase. The combined analysis of the Rietveld refinement and high resolution transmission electron microscopy (HRTEM) results proved that M+ ions were surely introduced into the intrinsic channels in Mg2Al4Si5O18. The emission peaks of MxMg2Al4+xSi5−xO18:Eu2+ (M = K, Rb) phosphors with various x values performed a systematic red-shift tendency, which was ascribed to the elongation of [MgO6] octahedra. The temperature stable photoluminescence and internal quantum efficiency (QE) of MxMg2Al4+xSi5−xO18:Eu2+ (M = K, Rb) phosphors were enhanced owing to the filling of M+ in the void channels suggesting a new insight to design the solid solution phosphors with improved photoluminescence properties. PMID:26190348

Highly solid-state emissive pyridinium-substituted tetraphenylethylene salts: emission color-tuning with counter anions and application for optical waveguides.

PubMed

Hu, Fang; Zhang, Guanxin; Zhan, Chi; Zhang, Wei; Yan, Yongli; Zhao, Yongsheng; Fu, Hongbing; Zhang, Deqing

2015-03-18

In this paper seven salts of pyridinium-substituted tetraphenylethylene with different anions are reported. They show typical aggregation-induced emission. Crystal structures of three of the salts with (CF(3)SO(2))(2) N(-), CF(3) SO(3)(-), and SbF(6)(-) as the respective counter anions, are determined. The emission behavior of their amorphous and crystalline solids is investigated. Both amorphous and crystalline solids, except for the one with I(-), are highly emissive. Certain amorphous solids are red-emissive with almost the same quantum yields and fluorescence life-times. However, some crystalline solids are found to show different emission colors varying from green to yellow. Thus, their emission colors can be tuned by the counter anions. Furthermore, certain crystalline solids are highly emissive compared to the respective amorphous solids. Such solid-state emission behavior of these pyridinium-substituted tetraphenylethylene salts is interpreted on the basis of their crystal structures. In addition, optical waveguiding behavior of fabricated microrods is presented. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Structural and compositional characterization of synthetic (Ca,Sr)-tremolite and (Ca,Sr)-diopside solid solutions

NASA Astrophysics Data System (ADS)

Gottschalk, M.; Najorka, J.; Andrut, M.

Tremolite (CaxSr1-x)2Mg5[Si8O22/(OH)2] and diopside (CaxSr1-x)Mg[Si2O6] solid solutions have been synthesized hydrothermally in equilibrium with a 1 molar (Ca,Sr)Cl2 aqueous solution at 750°C and 200 MPa. The solid run products have been investigated by optical, electron scanning and high resolution transmission electron microscopy, electron microprobe, X-ray-powder diffraction and Fourier-transform infrared spectroscopy. The synthesized (Ca,Sr)-tremolites are up to 2000 µm long and 30 µm wide, the (Ca,Sr)-diopsides are up to 150 µm long and 20 µm wide. In most runs the tremolites and diopsides are well ordered and chain multiplicity faults are rare. Nearly pure Sr-tremolite (tr0.02Sr-tr0.98) and Sr-diopside (di0.01Sr-di0.99) have been synthesized. A continuous solid solution series, i.e. complete substitution of Sr2+ for Ca2+ on M4-sites exists for (Ca,Sr)-tremolite. Total substitution of Sr2+ for Ca2+ on M2-sites can be assumed for (Ca,Sr)-diopsides. For (Ca,Sr)-tremolites the lattice parameters a, b and β are linear functions of composition and increase with Sr-content whereas c is constant. For the diopside series all 4 lattice parameters are a linear function of composition; a, b, c increase and β decreases with rising Sr-content. The unit cell volume for tremolite increases 3.47% from 906.68 Å3 for tremolite to 938.21 Å3 for Sr-tremolite. For diopside the unit cell volume increases 4.87 % from 439.91 Å3 for diopside to 461.30 Å3 for Sr-diopside. The observed splitting of the OH stretching band in tremolite is caused by different configurations of the next nearest neighbors (multi mode behavior). Resolved single bands can be attributed to the following configurations on the M4-sites: SrSr, SrCa, CaCa and CaMg. The peak positions of these 4 absorption bands are a linear function of composition. They are shifted to lower wavenumbers with increasing Sr-content. No absorption band due to the SrMg configuration on the M4-site is observed. This indicates a very low or negligible cummingtonite component in Sr-rich tremolites, which is also supported by electron microprobe analysis.

Copper-substituted perovskite compositions for solid oxide fuel cell cathodes and oxygen reduction electrodes in other electrochemical devices

DOEpatents

Rieke, Peter C [Pasco, WA; Coffey, Gregory W [Richland, WA; Pederson, Larry R [Kennewick, WA; Marina, Olga A [Richland, WA; Hardy, John S [Richland, WA; Singh, Prabhaker [Richland, WA; Thomsen, Edwin C [Richland, WA

2010-07-20

The present invention provides novel compositions that find advantageous use in making electrodes for electrochemical cells. Also provided are electrochemical devices that include active oxygen reduction electrodes, such as solid oxide fuel cells, sensors, pumps and the like. The compositions comprises a copper-substituted ferrite perovskite material. The invention also provides novel methods for making and using the electrode compositions and solid oxide fuel cells and solid oxide fuel cell assemblies having cathodes comprising the compositions.

Synthesis, spectroscopic and computational characterization of the tautomerism of pyrazoline derivatives from chalcones

NASA Astrophysics Data System (ADS)

Miguel, Fábio Balbino; Dantas, Juliana Arantes; Amorim, Stefany; Andrade, Gustavo F. S.; Costa, Luiz Antônio Sodré; Couri, Mara Rubia Costa

2016-01-01

In the present study a series of novel pyrazolines derivatives has been synthesized, and their structures assigned on the basis of FT-Raman, 1H and 13C NMR spectral data and computational DFT calculations. A joint computational study using B3LYP/6-311G(2d,2p) density functional theory and FT-Raman investigation on the tautomerism of 3-(4-substituted-phenyl)-4,5-dihydro-5-(4-substituted-phenyl)pyrazole-1-carbothioamide and 3-(4-substituted-phenyl)-4,5-dihydro-5-(4-substituted-phenyl)pyrazole-1-carboxamide are presented. The structures were characterized as a minimum in the potential energy surface using DFT. The calculated Raman and NMR spectra were of such remarkable agreement to the experimental results that the equilibrium between tautomeric forms has been discussed in detail. Our study suggests the existence of tautomers, the carboxamide/carbothioamide group may tautomerize, in the solid state or in solution. Thermodynamic data calculated suggests that the R(Cdbnd S)NH2 and R(Cdbnd O)NH2 species are more stable than the R(Cdbnd NH)SH and R(Cdbnd NH)OH species. Additionally, results found for the 1H NMR shifting, pointed out to which structure is present.

FTIR spectroscopic study of the phytohormone auxin (Indol-3-ylacetic Acid, IAA) and its n-alkylated and monohalogenated derivatives

NASA Astrophysics Data System (ADS)

Lutz, Bert T. G.; van der Windt, Erik; Kanters, Jan; Klämbt, Dieter; Kojić-Prodić, Biserka; Ramek, Michael

1996-09-01

In the framework of structure/activity correlation studies the plant growth hormone auxin and its natural analogue 4-Cl-IAA, as well as their synthetic congeners, were studied by FTIR spectroscopy. The analysis was focused on the NH and CO stretching vibrations which can be the most sensitive probes of intra- and intermolecular interactions, particularly to hydrogen bonds. However, it emerged that vC = O vibrations of both monomer and dimer are not affected by substitution. The aliphatic CH 2 group acts as an insulator between the conjugated π-system of indole and the carboxylic group, thus prohibiting a direct effect on the vibration CO. On the contrary, the stretching vibrations NH are influenced by halogenation and hydrogen bonding. The experimental data are in good agreement with the results of quantum chemical ab initio calculations of NH vibrations for IAA and several chlorine substituted IAAs. However, a simple correlation between substitution and spectral properties of indole NH cannot be found. The measurements were performed in the solid state (KBr pellets) and in polar (diethylether) and nonpolar (CDCI 3) solutions. From the measurements in diethylether, it follows that in dilute solution IAA and derivatives are predominantly present as monomer, whereas in CDCl 3 the equilibrium is in favour of the dimer form. In aqueous solution at the concentrations used in growth experiments solvated monomer will be the active component. Bioactivity of auxin and analogues with their NH stretching frequency shifts cannot be correlated in a simple way.

The lanthanum gallate-based mixed conducting perovskite ceramics

NASA Astrophysics Data System (ADS)

Politova, E. D.; Stefanovich, S. Yu.; Aleksandrovskii, V. V.; Kaleva, G. M.; Mosunov, A. V.; Avetisov, A. K.; Sung, J. S.; Choo, K. Y.; Kim, T. H.

2005-01-01

The structure, microstructure, dielectric, and transport properties of the anion deficient perovskite solid solutions (La,Sr)(Ga,Mg,M)O3- with M=Fe, Ni have been studied. Substitution of iron and nickel for gallium up to about 20 and 40 at.% respectively, leads to the perovskite lattice contraction due to the cation substitutions by the transition elements. The transition from pure ionic to mixed ionic-electronic conductivity was observed for both the systems studied. Both the enhancement of total conductivity and increasing in the thermal expansion coefficient values has been proved to correlate with the increasing amount of weakly bounded oxygen species in the Fe or Ni-doped ceramics. The oxygen ionic conductivity has been estimated from the kinetic experiments using the dc-conductivity and dilatometry methods under the condition of the stepwise change of the atmosphere from nitrogen to oxygen.

Cisplatin Binding to Biological Ligands Revealed at the Encounter Complex Level by IR Action Spectroscopy.

PubMed

Corinti, Davide; Coletti, Cecilia; Re, Nazzareno; Chiavarino, Barbara; Crestoni, Maria Elisa; Fornarini, Simonetta

2016-03-07

Cisplatin [cis-diamminedichloroplatinum(II)] was the first platinum-based antineoplastic agent and is still a cornerstone for the treatment of various solid tumors. Reactive events responsible for cisplatin activity are unveiled here at the molecular level. Simple ligands (L) representing ubiquitous functional groups in the biological environment likely to be encountered by administered cisplatin have been allowed to react with cis-[PtCl(NH3)2 (H2O)](+), the primary intermediate from cisplatin hydrolysis. The substitution reactions have been examined by a combined experimental and computational approach and the structural features of the substitution product, cis-[PtCl(NH3)2(L)](+), have been probed by IR multiple-photon dissociation (IRMPD) spectroscopy. Furthermore, IRMPD spectroscopy has been exploited to elucidate the structure of [PtCl(NH3)2(L)(H2O)](+) clusters, also obtained by electrospray ionization (ESI) from the aqueous solution and representing the major focus of this investigation. These ions conform to the encounter complex of cis-[PtCl(NH3)2 (H2O)](+) with the incoming ligand and represent the first direct evidence of a prototypical Eigen-Wilkins encounter complex in solution, lying on the reaction coordinate for ligand substitution and extracted by ESI for mass spectrometric analysis. Activated [PtCl(NH3)2(L)(H2O)](+) ions dissociate by the loss of either H2O or L, the former process implying a ligand substitution event. IRMPD spectroscopy has thus revealed both structural details and reaction dynamics at the level of the isolated encounter complex. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Effect of reduction of strategic Columbium addition in 718 Alloy on the structure and properties

NASA Technical Reports Server (NTRS)

Ziegler, K. R.; Wallace, J. F.

1985-01-01

A series of alloys was developed having a base composition similar to Inconel 718, with reduced Cb levels of 3.00 and 1.10 wt% Cb. Substitutions of 3.0% W, 3.0W + 0.9V or Mo increased from 3.0% to 5.8% were made for the Cb in these alloys. Two additional alloys, one containing 3.49% Cb and 1.10% Ti and another containing 3.89% Cb and 1.29% Ti were also studied. Tensile properties at rooom and elevated temperatures, stress-rupture tests, and an analysis of extracted phases were carried out for each of the alloys. Additions of solid solution elements to a reduced Cb alloy had no significant effect on the properties of the alloys under either process condition. The solution and age alloys with substitutions of 1.27% i at 3.89% Cb had tensile properties similar top hose of the original alloy and stress-rupture properties superior to the original alloy. The improved stress-rupture properties were the result of significant precipitation of Ni3Ti-gamma prime in the alloy, which is more stable than gamma' at the elevated temperatures. At lower temperatures, the new alloy benefits from gamma' strengthening. With more precise control and proper processing, the reduced Cb direct-age alloy could substitute for Alloy 718 in high strength applications.

The effect of relative solubility on crystal purity

NASA Astrophysics Data System (ADS)

Givand, Jeffrey Christopher

This study establishes the relationship between impurity incorporation in a crystal by lattice substitution and the solubility of that impurity in solution. The model system studied was L-isoleucine crystals contaminated by the isomorphic impurity L-leucine. Upon crystallization from aqueous solution by cooling, leucine is concentrated in the isoleucine unit cell through lattice substitution mechanisms. Attempts to reduce the degree of leucine incorporation via adjustments of the rate at which supersaturation is generated yielded marginal success. This work demonstrates that incorporation of leucine in the crystal can be considerably suppressed by reducing the solubility of product relative to the solubility of impurity. Changes to the relative solubility of the impurity were accomplished by the addition of various electrolytes and organic co-solvents to the aqueous amino acid solutions. The solubilities of the two amino acids were measured and compared to their solubilities in pure water. Changes in the ratio of pure-component solubilities were directly related to changes in crystal purity. This thermodynamic quantity of relative solubility was shown to be a key factor in determining impurity uptake by lattice substitution. In addition to the experimental observations, a fundamental thermodynamic link between relative solubility and crystal purity is established through this research. First, the amino acid solubility data as a function of temperature in all solvent mixtures were accurately correlated using a thermodynamic model. The parameters from this model were then adapted to a novel solid-solution thermodynamic model to express the crystal purity in terms of equilibrium solution impurity concentration. After the determination of one system specific parameter, the model is able to predict the crystal purity in a new solvent in which the pure-component solubilities are known. The ability of an electrolyte or co-solvent to improve crystal purity from a given level can now be determined based on existing solubility and purity measurements and solubilities of the product and impurity in the new solvent mixture.

Nonstoichiometry of Epitaxial FeTiO(3+delta) Films

DTIC Science & Technology

2003-01-01

nonstoichiometry of the FeTiO3 +8 films was probably produced by cation vacancies and disarrangement of Fe3+ and Ti4 ions, which randomly occupied both interstitial...and substitutional sites of the FeTiO 3 related structure. INTRODUCTION Solid solutions of ot-Fe20 3- FeTiO3 (hematite-ilmenite) series are known to...tried to confirm preparation conditions of stoichiometric FeTiO 3 films. According to a literature on bulk crystal growth of FeTiO3 [5], very low oxygen

Structural, Kinetic And Magnetic Properties Of Mechanically Alloyed Fe-Zr Powders

NASA Astrophysics Data System (ADS)

Mishra, Debabrata; Perumal, A.; Srinivasan, A.

2008-04-01

We report the study of amorphous/non-equilibrium solid solution Fe100-xZrx (x = 20 to 35) alloys by mechanical alloying process. It is observed that with increasing Zr substitution, (a) the activation energy increases, (b) the saturation magnetization and coercivity show oscillating behavior. Low temperature magnetic measurements show the presence of spin-glass like phase transition even at H = 10 kOe. The oscillating behavior of magnetic parameters is explained on the basis of variations in the average internal stress calculated using magnetic data.

The appropriate use of technology (particularly in medical problems of the elderly).

PubMed

Gilbert, F I

1990-09-01

Technology, particularly "high" technology, with little solid data, is often blamed for much of our increasing cost of health care. Politics and emotions are poor substitutes for accurate information needed for rational solutions. By targeting the desired outcome and studying the process needed to reach the outcome, we can make better decisions. The methods of designing, conducting and funding the studies needed to answer the difficult questions posed by the use of high technology in the elderly are available. Do we have the wisdom to use them?

Aluminum Coprecipitates with Fe (hydr)oxides: Does Isomorphous Substitution of Al3plus for Fe3plus in Goethite Occur

DOE Office of Scientific and Technical Information (OSTI.GOV)

E Bazilevskaya; D Archibald; M Aryanpour

2011-12-31

Iron (hydr)oxides are common in natural environments and typically contain large amounts of impurities, presumably the result of coprecipitation processes. Coprecipitation of Al with Fe (hydr)oxides occurs, for example, during alternating reduction-oxidation cycles that promote dissolution of Fe from Fe-containing phases and its re-precipitation as Fe-Al (hydr)oxides. We used chemical and spectroscopic analyses to study the formation and transformation of Al coprecipitates with Fe (hydr)oxides. In addition, periodic density functional theory (DFT) computations were performed to assess the structural and energetic effects of isolated or clustered Al atoms at 8 and 25 mol% Al substitution in the goethite structure. Coprecipitatesmore » were synthesized by raising the pH of dilute homogeneous solutions containing a range of Fe and Al concentrations (100% Fe to 100% Al) to 5. The formation of ferrihydrite in initial suspensions with {<=}20 mol% Al, and of ferrihydrite and gibbsite in initial suspensions with {>=}25 mol% Al was confirmed by infrared spectroscopic and synchrotron-based X-ray diffraction analyses. While base titrations showed a buffer region that corresponded to the hydrolysis of Fe in initial solutions with {<=}25 mol% Al, all of the Al present in these solutions was retained by the solid phases at pH 5, thus indicating Al coprecipitation with the primary Fe hydroxide precipitate. In contrast, two buffer regions were observed in solutions with 30 mol% Al (at pH {approx}2.25 for Fe{sup 3+} and at pH {approx}4 for Al{sup 3+}), suggesting the formation of Fe and Al (hydr)oxides as two separate phases. The Al content of initial coprecipitates influenced the extent of ferrihydrite transformation and of its transformation products as indicated by the presence of goethite, hematite and/or ferrihydrite in aged suspensions. DFT experiments showed that: (i) optimized unit cell parameters for Al-substituted goethites (8 and 25 Mol% Al) in clustered arrangement (i.e., the formation of diaspore-like clusters) were in good agreement with available experimental data whereas optimized unit cell parameters for isolated Al atoms were not, and (ii) Al-substituted goethites with Al in diaspore-like clusters resulted in more energetically favored structures. Combined experimental and DFT results are consistent with the coprecipitation of Al with Fe (hydr)oxides and with the formation of diaspore-like clusters, whereas DFT results suggest isomorphous Al for Fe substitution within goethite is unlike at 8 mol% Al substitution.« less

Arsenic incorporation into FeS 2 pyrite and its influence on dissolution: A DFT study

NASA Astrophysics Data System (ADS)

Blanchard, Marc; Alfredsson, Maria; Brodholt, John; Wright, Kate; Catlow, C. Richard A.

2007-02-01

FeS 2 pyrite can incorporate large amounts of arsenic (up to ca. 10 wt%) and hence has a strong impact on the mobility of this toxic metalloid. Focussing on the lowest arsenic concentrations for which the incorporation occurs in solid solution, the substitution mechanisms involved have been investigated by assuming simple incorporation reactions in both oxidising and reducing conditions. The solution energies were calculated by Density Functional Theory (DFT) calculations and we predict that the formation of AsS dianion groups is the most energetically favourable mechanism. The results also suggest that the presence of arsenic will accelerate the dissolution and thus the generation of acid drainage, when the crystal dissolves in oxidising conditions.

Experimental study of the Ca-Mg-Zn system using diffusion couples and key alloys

NASA Astrophysics Data System (ADS)

Zhang, Yi-Nan; Kevorkov, Dmytro; Bridier, Florent; Medraj, Mamoun

2011-03-01

Nine diffusion couples and 32 key samples were prepared to map the phase diagram of the Ca-Mg-Zn system. Phase relations and solubility limits were determined for binary and ternary compounds using scanning electron microscopy, electron probe microanalysis and x-ray diffraction (XRD). The crystal structure of the ternary compounds was studied by XRD and electron backscatter diffraction. Four ternary intermetallic (IM) compounds were identified in this system: Ca3MgxZn15-x (4.6<=x<=12 at 335 °C, IM1), Ca14.5Mg15.8Zn69.7 (IM2), Ca2Mg5Zn13 (IM3) and Ca1.5Mg55.3Zn43.2 (IM4). Three binary compounds were found to have extended solid solubility into ternary systems: CaZn11, CaZn13 and Mg2Ca form substitutional solid solutions where Mg substitutes for Zn atoms in the first two compounds, and Zn substitutes for both Ca and Mg atoms in Mg2Ca. The isothermal section of the Ca-Mg-Zn phase diagram at 335 °C was constructed on the basis of the obtained experimental results. The morphologies of the diffusion couples in the Ca-Mg-Zn phase diagram at 335 °C were studied. Depending on the terminal compositions of the diffusion couples, the two-phase regions in the diffusion zone have either a tooth-like morphology or contain a matrix phase with isolated and/or dendritic precipitates.

The Impact of Chemical Substitutions on Interfacial Properties of REE Orthophosphates (Monazite, Xenotime)

NASA Astrophysics Data System (ADS)

Gamage McEvoy, J.; Thibault, Y.

2016-12-01

Mineral surface properties strongly influence liquid-solid interface behaviour in the presence of various ligands, and can significantly affect processes of natural (ex. fluids, melts) and industrial (ex. oil recovery) relevance. Many Rare Earth Element (REE)-bearing minerals display extensive solid solutions resulting in significant chemical variations which influence their crystal and surface properties and, can consequently impact the interfacial features of their interaction with substances such as organic molecules (i.e. reactivity and sorption). For example, the surface charge properties of some REE orthophosphates show an uncharacteristically wide variation in reported values, where large differences in literature are commonly attributed to compositional differences between samples. However the impact of these chemical substitutions remains largely unknown. As such, the aim of this research was to systematically investigate the influence of mineralogical variation within the compositional space of the REE orthophosphates on their surface chemistry and resulting interaction with organic molecules. To better isolate the chemical, structural, and morphological variables, the synthesis of REE orthophosphate crystals along a number of defined substitutions was conducted, and their surface chemistry characteristics benchmarked against well-characterized natural monazite and xenotime from various localities. The interaction of these crystal surfaces with model organic molecules (long chain carboxylic acids and alkyl hydroxamic acids, respectively) was then studied and characterized via surface (X-ray photoelectron) and near-surface (vibrational) spectroscopic techniques. The implications of crystal surface-organic molecule interactions to mineral processing through flotation were also experimentally investigated.

Dibutyl Phosphoric Acid Solubility in High-Acid, Uranium-Bearing Solutions at SRS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pierce, R.A.

1998-10-02

The Savannah River Site has enriched uranium (EU) solution which has been stored for almost 10 years since being purified in the second uranium cycle of the H area solvent extraction process. The concentrations in solution are approximately 6 g/L U and about 0.1 M nitric acid. Residual tributylphosphate in the solutions has slowly hydrolyzed to form dibutyl phosphoric acid (HDBP) at concentrations averaging 50 mg/L. Uranium is known to form compounds with the dibutylphosphate ion (DBP) which have limited solubility. The potential to form uranium-DBP solids raises a nuclear criticality safety issue. Prior SRTC tests (WSRC-TR-98-00188) showed that U-DBPmore » solids precipitate at concentrations potentially attainable during the storage of enriched uranium solutions. Furthermore, evaporation of the existing EUS solution without additional acidification could result in the precipitation of U-DBP solids if the DBP concentration in the resulting solution exceeds 110 mg/L at ambient temperature. The same potential exists for evaporation of unwashed 1CU solutions. As a follow-up to the earlier studies, SRTC studied the solubility limits for solutions containing acid concentrations above 0.5M HNO3. The data obtained in these tests reveals a shift to higher levels of DBP solubility above 0.5M HNO3 for both 6 g/L and 12 g/L uranium solutions. Analysis of U-DBP solids from the tests identified a mixture of different molecular structures for the solids created. The analysis distinguished UO2(DBP)2 as the dominant compound present at low acid concentrations. As the acid concentration increases, the crystalline UO2(DBP)2 shows molecular substitutions and an increase in amorphous content. Further analysis by methods not available at SRS will be needed to better identify the specific compounds present. This data indicates that acidification prior to evaporation can be used to increase the margin of safety for the storage of the EUS solutions. Subsequent experimentation evaluated options for absorbing HDBP from solution using either activated carbon or anion exchange resin. The activated carbon outperformed the anion exchange resin. Activated carbon absorbs DBP rapidly and has demonstrated the capability of absorbing 15 mg of DBP per gram of activated carbon. Analytical results also show that activated carbon absorbs uranium up to 17 mg per gram of carbon. It is speculated that the uranium absorbed is part of a soluble U-DBP complex that has been absorbed. Additional testing must still be performed to 1) establish absorption limits for uranium for anion exchange resin, 2) evaluate desorption characteristics of uranium and DBP, and 3) study the possibility of re-using the absorbent.« less

Investigating the local structure of B-site cations in (1-x)BaTiO3-xBiScO3 and (1-x)PbTiO3-xBiScO3 using X-ray absorption spectroscopy

NASA Astrophysics Data System (ADS)

Blanchard, Peter E. R.; Grosvenor, Andrew P.

2018-05-01

The structural properties of (1-x)BaTiO3-xBiScO3 and (1-x)PbTiO3-xBiScO3 were investigated using powder X-ray diffraction and X-ray absorption spectroscopy. Diffraction measurements confirmed that substituting small amounts of BiScO3 into BaTiO3 initially stabilizes a cubic phase at x = 0.2 before impurity phases begin to form at x = 0.5. BiScO3 substitution also resulted in noticeable changes in the local coordination environment of Ti4+. X-ray absorption near-edge spectroscopy (XANES) analysis showed that replacing Ti4+ with Sc3+ results in an increase in the off-centre displacement of Ti4+ cations. Surprisingly, BiScO3 substitution has no effect on the displacement of the Ti4+ cation in the (1-x)PbTiO3-xBiScO3 solid solution.

Stacking interactions between nitrogen-containing six-membered heterocyclic aromatic rings and substituted benzene: studies in solution and in the solid state.

PubMed

Gung, Benjamin W; Wekesa, Francis; Barnes, Charles L

2008-03-07

The stacking interactions between an aromatic ring and a pyridine or a pyrimidine ring are studied by using a series of triptycene-derived scaffolds. The indicative ratios of the syn and anti conformers were determined by variable-temperature NMR spectroscopy. The syn conformer aligns the attached aromatic ring and the heterocycle in a parallel-displaced orientation while the anti conformer sets the two rings apart from each other. Comparing to the corresponding control compounds where a benzene ring is in the position of the heterocycle, higher attractive interactions are observed as indicated by the higher syn/anti ratios. In general, the attractive interactions are much less sensitive to the substituent effects than the corresponding nonheterocycles. The greatest attractive interactions were observed between a pyrimidine ring and a N,N-dimethylaminobenzene, consistent with a predominant donor-acceptor interaction. The interactions between a pyridine ring and a substituted benzene ring show that the pyridine is comparable to that of a NO2- or a CN-substituted benzene ring except for the unpredictable substituent effects.

Thermoelectric Properties of Cu-doped Bi2-xSbxTe3 Prepared by Encapsulated Melting and Hot Pressing

NASA Astrophysics Data System (ADS)

Jung, Woo-Jin; Kim, Il-Ho

2018-03-01

P-type Bi2-xSbxTe3:Cum (x = 1.5-1.7 and m = 0.002-0.003) solid solutions were synthesized using encapsulated melting and were consolidated using hot pressing. The effects of Sb substitution and Cu doping on the charge transport and thermoelectric properties were examined. The lattice constants decreased with increasing Sb and Cu contents. As the amount of Sb substitution and Cu doping was increased, the electrical conductivity increased, and the Seebeck coefficient decreased owing to the increase in the carrier concentration. All specimens exhibited degenerate semiconductor characteristics and positive Hall and Seebeck coefficients, indicating p-type conduction. The increased Sb substitution caused a shift in the onset temperature of the intrinsic transition and bipolar conduction to higher temperatures. The electronic thermal conductivity increased with increasing Sb and Cu contents owing to the increase in the carrier concentration, while the lattice thermal conductivity slightly decreased due to alloy scattering. A maximum figure of merit, ZTmax = 1.25, was achieved at 373 K for Bi0.4Sb1.6Te3:Cu0.003.

Conformational Plasticity of the Cell-Penetrating Peptide SAP As Revealed by Solid-State 19F-NMR and Circular Dichroism Spectroscopies.

PubMed

Afonin, Sergii; Kubyshkin, Vladimir; Mykhailiuk, Pavel K; Komarov, Igor V; Ulrich, Anne S

2017-07-13

The cell-penetrating peptide SAP, which was designed as an amphipathic poly-l-proline helix II (PPII), was suggested to self-assemble into regular fibrils that are relevant for its internalization. Herein we have analyzed the structure of SAP in the membrane-bound state by solid-state 19 F-NMR, which revealed other structural states, in addition to the expected surface-aligned PPII. Trifluoromethyl-bicyclopentyl-glycine (CF 3 -Bpg) and two rigid isomers of trifluoromethyl-4,5-methanoprolines (CF 3 -MePro) were used as labels for 19 F-NMR analysis. The equilibria between different conformations of SAP were studied and were found to be shifted by the substituents at Pro-11. Synchrotron-CD results suggested that substituting Pro-11 by CF 3 -MePro governed the coil-to-PPII equilibrium in solution and in the presence of a lipid bilayer. Using CD and 19 F-NMR, we examined the slow kinetics of the association of SAP with membranes and the dependence of the SAP conformational dynamics on the lipid composition. The peptide did not bind to lipids in the solid ordered phase and aggregated only in the liquid ordered "raft"-like bilayers. Self-association could not be detected in solution or in the presence of liquid disordered membranes. Surface-bound amphipathic SAP in a nonaggregated state was structured as a mixture of nonideal extended conformations reflecting the equilibrium already present in solution, i.e., before binding to the membrane.

Structural effects in the interstitial solid solution system (La,Ce)(Fe,Si)13Cx-H: Correlation with hydrogenation kinetics

NASA Astrophysics Data System (ADS)

Hai, X.; Porcher, F.; Mayer, C.; Miraglia, S.

2018-02-01

Steady state and in-situ neutron powder diffraction on selected compositions of the magneto-caloric (La,Ce)(Fe,Si)13CxHy compounds has been used to locate the sites accommodated by the interstitial species and to reveal the structural modifications (breathing) that occur upon metal substitution and/or interstitial insertion. The latter type of measurement in which the sequential filling of interstitial sites is followed allows one to extract some useful hydrogenation kinetics data. This structural investigation has allowed to precise the deformations undergone by the complex metallic alloys La(Fe,Si)13 when subjected to light interstitial insertion or rare earth substitution at the cation site of the NaZn13-structure type. We attempt to correlate hydrogenation kinetics variations (depression or enhancement of the hydrogen absorption rate) with a particular inhomogeneous cell variation (breathing) and bonding of the NaZn13 structure-type.

Tuning magnetic properties in quasi-two-dimensional ferromagnetic Fe3-y Ge1-x As x Te2 (0  ⩽  x  ⩽  0.85)

NASA Astrophysics Data System (ADS)

Yuan, Duanduan; Jin, Shifeng; Liu, Ning; Shen, Shijie; Lin, Zhiping; Li, Kunkun; Chen, Xiaolong

2017-03-01

We report that Fe3GeTe2 can form a wide solid solution by substitution of As for Ge, providing an opportunity to tune the magnetic and electronic properties in this 2D material. The crystal structure, physical properties and electronic structure of iron-deficient solid solution Fe3-y Ge1-x As x Te2 (0  ⩽  x  ⩽  0.85) are studied. We found that the Curie temperature can substantially change from 177 K to 33 K and resistivity decreases by about 30% with the arsenic doping x from 0 to 0.85. First principles calculations demonstrate that the elongation of Fe(1)-Fe(1) dumb-bells along c axis is essentially responsible for decreasing the integrated spin density of states below Fermi level and weakening spin polarization, resulting in a decrease of Curie temperature. Our study reveals the magnetism manipulation can be realized via modification of bondlengths in 2D magnetic materials.

Optimizing Blue Persistent Luminescence in (Sr 1-δ Ba δ ) 2 MgSi 2 O 7: Eu 2+ ,Dy 3+ via Solid Solution for Use in Point-of-Care Diagnostics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Finley, Erin; Cobb, Angelica; Duke, Anna

Inorganic persistent luminescent phosphors are an excellent class of optical reporters for enabling sensitive point-of-care diagnostics, particularly with smartphone-based biosensing devices in testing formats such as the lateral flow assay (LFA). Here, the development of persistent phosphors for this application is focused on the solid solution (Sr 1-δBa δ) 2MgSi 2O 7:Eu 2+,Dy 3+ (δ = 0, 0.125, 0.25, 0.375), which is prepared using a high-temperature solid-state reaction as confirmed by synchrotron X-ray powder diffraction. The substitution of barium for strontium enables control over the Eu 2+ 5d-orbital crystal field splitting (CFS) as a tool for tuning the emission wavelengthmore » while maintaining luminescence lifetimes >9 min across the composition range. Thermoluminescence measurements of the solid solution provide evidence that trap states contribute to the persistent lifetimes with the trap depths also remaining constant as a function of composition. Time-gated luminescence images of these compounds are captured on a smartphone arranged in a layout to mimic a point-of-care test and demonstrate the viability of using these materials as optical reporters. Moreover, comparing the blue-emitting (Sr 0.625Ba 0.375) 2MgSi 2O 7:Eu 2+,Dy 3+ and the green-emitting SrAl 2O 4:Eu 2+,Dy 3+ in a single LFA-type format shows these two compounds can be detected and resolved simultaneously, thereby permitting the development of a multiplexed LFA.« less

Numerical Modeling of Saturated Boiling in a Heated Tube

NASA Technical Reports Server (NTRS)

Majumdar, Alok; LeClair, Andre; Hartwig, Jason

2017-01-01

This paper describes a mathematical formulation and numerical solution of boiling in a heated tube. The mathematical formulation involves a discretization of the tube into a flow network consisting of fluid nodes and branches and a thermal network consisting of solid nodes and conductors. In the fluid network, the mass, momentum and energy conservation equations are solved and in the thermal network, the energy conservation equation of solids is solved. A pressure-based, finite-volume formulation has been used to solve the equations in the fluid network. The system of equations is solved by a hybrid numerical scheme which solves the mass and momentum conservation equations by a simultaneous Newton-Raphson method and the energy conservation equation by a successive substitution method. The fluid network and thermal network are coupled through heat transfer between the solid and fluid nodes which is computed by Chen's correlation of saturated boiling heat transfer. The computer model is developed using the Generalized Fluid System Simulation Program and the numerical predictions are compared with test data.

Understanding high diastereomeric discrimination in formation of oligoribonucleotide phosphorothioate linkages: the first study of pKa-dependent activation in solid-supported coupling of 2'-O-substituted ribonucleoside phosphoramidites.

PubMed

Ravikumar, Vasulinga T; Cole, Douglas L

2003-01-01

Activation of 2'-O-substituted ribonucleoside phosphoramidites with various activators during solid-supported synthesis of phosphorothioate oligonucleotides was studied. The Rp:Sp diastereomeric composition of resulting phosphorothioate linkage dependent on pKa of activator utilized for coupling.

C-shaped diastereomers containing cofacial thiophene-substituted quinoxaline rings: synthesis, photophysical properties, and X-ray crystallography.

PubMed

DeBlase, Catherine R; Finke, Ryan T; Porras, Jonathan A; Tanski, Joseph M; Nadeau, Jocelyn M

2014-05-16

Synthesis and characterization of two diastereomeric C-shaped molecules containing cofacial thiophene-substituted quinoxaline rings are described. A previously known bis-α-diketone was condensed with an excess of 4-bromo-1,2-diaminobenzene in the presence of zinc acetate to give a mixture of two C-shaped diastereomers with cofacial bromine-substituted quinoxaline rings. After chromatographic separation, thiophene rings were installed by a microwave-assisted Suzuki coupling reaction, resulting in highly emissive diastereomeric compounds that were studied by UV-vis, fluorescence, and NMR spectroscopy, as well as X-ray crystallography. The unique symmetry of each diastereomer was confirmed by NMR spectroscopy. NMR data indicated that the syn isomer has restricted rotation about the bond connecting the thiophene and quinoxaline rings, which was also observed in the solid state. The spectroscopic properties of the C-shaped diastereomers were compared to a model compound containing only a single thiophene-substituted quinoxaline ring. Ground state intramolecular π-π interactions in solution were detected by NMR and UV-vis spectroscopy. Red-shifted emission bands, band broadening, and large Stokes shifts were observed, which collectively suggest excited state π-π interactions that produce excimer-like emissions, as well as a remarkable positive emission solvatochromism, indicating charge-transfer character in the excited state.

Synthesis, spectroscopic and computational characterization of the tautomerism of pyrazoline derivatives from chalcones.

PubMed

Miguel, Fábio Balbino; Dantas, Juliana Arantes; Amorim, Stefany; Andrade, Gustavo F S; Costa, Luiz Antônio Sodré; Couri, Mara Rubia Costa

2016-01-05

In the present study a series of novel pyrazolines derivatives has been synthesized, and their structures assigned on the basis of FT-Raman, (1)H and (13)C NMR spectral data and computational DFT calculations. A joint computational study using B3LYP/6-311G(2d,2p) density functional theory and FT-Raman investigation on the tautomerism of 3-(4-substituted-phenyl)-4,5-dihydro-5-(4-substituted-phenyl)pyrazole-1-carbothioamide and 3-(4-substituted-phenyl)-4,5-dihydro-5-(4-substituted-phenyl)pyrazole-1-carboxamide are presented. The structures were characterized as a minimum in the potential energy surface using DFT. The calculated Raman and NMR spectra were of such remarkable agreement to the experimental results that the equilibrium between tautomeric forms has been discussed in detail. Our study suggests the existence of tautomers, the carboxamide/carbothioamide group may tautomerize, in the solid state or in solution. Thermodynamic data calculated suggests that the R(CS)NH2 and R(CO)NH2 species are more stable than the R(CNH)SH and R(CNH)OH species. Additionally, results found for the (1)H NMR shifting, pointed out to which structure is present. Copyright © 2015 Elsevier B.V. All rights reserved.

In Situ Tracking Kinetic Pathways of Li+/Na+ Substitution during Ion-Exchange Synthesis of LixNa1.5-xVOPO4F0.5.

PubMed

Park, Young-Uk; Bai, Jianming; Wang, Liping; Yoon, Gabin; Zhang, Wei; Kim, Hyungsub; Lee, Seongsu; Kim, Sung-Wook; Looney, J Patrick; Kang, Kisuk; Wang, Feng

2017-09-13

Ion exchange is a ubiquitous phenomenon central to wide industrial applications, ranging from traditional (bio)chemical separation to the emerging chimie douce synthesis of materials with metastable structure for batteries and other energy applications. The exchange process is complex, involving substitution and transport of different ions under non-equilibrium conditions, and thus difficult to probe, leaving a gap in mechanistic understanding of kinetic exchange pathways toward final products. Herein, we report in situ tracking kinetic pathways of Li + /Na + substitution during solvothermal ion-exchange synthesis of Li x Na 1.5-x VOPO 4 F 0.5 (0 ≤ x ≤ 1.5), a promising multi-Li polyanionic cathode for batteries. The real-time observation, corroborated by first-principles calculations, reveals a selective replacement of Na + by Li + , leading to peculiar Na + /Li + /vacancy orderings in the intermediates. Contradicting the traditional belief of facile topotactic substitution via solid solution reaction, an abrupt two-phase transformation occurs and predominantly governs the kinetics of ion exchange and transport in the 1D polyanionic framework, consequently leading to significant difference of Li stoichiometry and electrochemical properties in the exchanged products. The findings may help to pave the way for rational design of ion exchange synthesis for making new materials.

Synergetic effect of Zn substitution on the electron and phonon transport in Mg2Si0.5Sn0.5-based thermoelectric materials.

PubMed

Gao, Hongli; Zhu, Tiejun; Zhao, Xinbing; Deng, Yuan

2014-10-07

Mg2Si1-xSnx alloys are a prospective material for thermoelectric generators at moderate temperatures. The thermoelectric properties of Mg2Si0.5Sn0.5-based thermoelectric materials with only Zn substitution or Zn/Sb co-doping were investigated. Isoelectronic Zn substitution did not affect the carrier concentration, but improved the carrier mobility. Zn atoms incorporated into a Sb-doped Mg2Si0.5Sn0.5 matrix simultaneously boosted the power factor and suppressed the lattice thermal conductivity, leading to an enhancement of the thermoelectric figure of merit ZT of the resulting bulk materials. The interplay between the electron and phonon transport of Mg2Si0.5Sn0.49Sb0.01 substituted with Zn at Mg sites results in an enhancement of the ZT by 25% at ∼730 K, from ZT≈ 0.8 in Mg2Si0.5Sn0.49Sb0.01 to ZT≈ 1.0 in Mg1.98Zn0.02Si0.5Sn0.49Sb0.01. Solid solutions in the Mg2Si-Mg2Sn system appear to be more promising for thermoelectric applications.

Dielectric Studies of Samarium Modified (Pb)(Zr, Ti, Fe, Nb)O3 Ceramic System

NASA Astrophysics Data System (ADS)

Singh, Pratibha; Singh, Sangeeta; Juneja, J. K.; Prakash, Chandra; Raina, K. K.

Here we report the investigations on Sm-substituted PZTFN (Pb1-xSmxZr0.588Ti0.392Fe0.01Nb0.01O3) (where x = 0, 0.02, 0.04, 0.06, 0.08, 0.10) polycrystalline solid solutions fabricated by solid-state reaction method. XRD analysis shows all the samples to be single phase with tetragonal structure. Dielectric measurements were carried out in the temperature range 30°C-400°C at different frequencies in the range 100 Hz to 100 kHz. From the temperature variation of dielectric constant (ɛ), Curie temperature (TC) was determined which was found to decrease with increasing x. The room temperature dielectric constant (ɛRT) initially increases with increasing x and then starts decreasing. Dielectric loss improves with Sm-doping.

Heat capacity and magnetocaloric effect in manganites (La 1- yEu y) 0.7Pb 0.3MnO 3 ( y:0.2; 0.6)

NASA Astrophysics Data System (ADS)

Kartashev, A. V.; Flerov, I. N.; Volkov, N. V.; Sablina, K. A.

2010-03-01

Heat capacity and intensive magnetocaloric effect (MCE) in manganites (La 1- yEu y) 0.7Pb 0.3MnO 3 [ y=0.2; 0.6] (LEPM) were investigated by means of adiabatic calorimeter. The heat capacity anomaly as well as the values of both the intensive (Δ TAD) and the extensive (Δ SMCE) MCE were found to decrease upon increased replacement of La with nonmagnetic Eu. However, because of widening of the MCE peaks, the LEPM compounds show the relative cooling power, RCP/Δ H, comparable to other solid solutions of manganites. Owing to strong effect of Eu→La substitution on the Curie temperature, LEPM might have potential as the solid state refrigerants in multi-element cooling apparatus operating in a wide temperature range.

Proline Editing: A General and Practical Approach to the Synthesis of Functionally and Structurally Diverse Peptides. Analysis of Steric versus Stereoelectronic Effects of 4-Substituted Prolines on Conformation within Peptides

PubMed Central

Pandey, Anil K.; Naduthambi, Devan; Thomas, Krista M.; Zondlo, Neal J.

2013-01-01

Functionalized proline residues have diverse applications. Herein we describe a practical approach, proline editing, for the synthesis of peptides with stereospecifically modified proline residues. Peptides are synthesized by standard solid-phase-peptide-synthesis to incorporate Fmoc-Hydroxyproline (4R-Hyp). In an automated manner, the Hyp hydroxyl is protected and the remainder of the peptide synthesized. After peptide synthesis, the Hyp protecting group is orthogonally removed and Hyp selectively modified to generate substituted proline amino acids, with the peptide main chain functioning to “protect” the proline amino and carboxyl groups. In a model tetrapeptide (Ac-TYPN-NH2), 4R-Hyp was stereospecifically converted to 122 different 4-substituted prolyl amino acids, with 4R or 4S stereochemistry, via Mitsunobu, oxidation, reduction, acylation, and substitution reactions. 4-Substituted prolines synthesized via proline editing include incorporated structured amino acid mimetics (Cys, Asp/Glu, Phe, Lys, Arg, pSer/pThr), recognition motifs (biotin, RGD), electron-withdrawing groups to induce stereoelectronic effects (fluoro, nitrobenzoate), handles for heteronuclear NMR (19F:fluoro; pentafluorophenyl or perfluoro-tert-butyl ether; 4,4-difluoro; 77SePh) and other spectroscopies (fluorescence, IR: cyanophenyl ether), leaving groups (sulfonate, halide, NHS, bromoacetate), and other reactive handles (amine, thiol, thioester, ketone, hydroxylamine, maleimide, acrylate, azide, alkene, alkyne, aryl halide, tetrazine, 1,2-aminothiol). Proline editing provides access to these proline derivatives with no solution phase synthesis. All peptides were analyzed by NMR to identify stereoelectronic and steric effects on conformation. Proline derivatives were synthesized to permit bioorthogonal conjugation reactions, including azide-alkyne, tetrazinetrans-cyclooctene, oxime, reductive amination, native chemical ligation, Suzuki, Sonogashira, cross-metathesis, and Diels-Alder reactions. These proline derivatives allowed three parallel bioorthogonal reactions to be conducted in one solution. PMID:23402492

Immobilization of 99-Technetium (VII) by Fe(II)-Goethite and Limited Reoxidation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Um, Wooyong; Chang, Hyun-Shik; Icenhower, Jonathan P.

2011-05-04

Synthesized goethite was successfully used with addition of Fe(II) to sequester Tc present in both deionized water and simulated off-gas scrubber waste solutions. Pertechnetate concentration in solution decreased immediately when the pH was raised above 7 by addition of sodium hydroxide. Removal of Tc(VII) from solution occurred most likely as a result of heterogeneous surface-catalyzed reduction to Tc(IV) and subsequent co-precipitation onto the goethite. The final Tc-bearing solid was identified as goethite-dominated Fe(III)-(oxy)hydroxide based on XRD analysis, confirming the widespread observation of its characteristic acicular habit by TEM/SEM images. Analysis of the solid precipitate by XAFS showed that the dominantmore » oxidation state of Tc was Tc(IV) and was in octahedral coordination with Tc-O, Fe-O, and Tc-Fe bond distances that are consistent with direct substitution of Tc for Fe in the goethite structure. In some experiments the final Tc-goethite product was subsequently armored with additional layers of freshly precipitated goethite. Successful incorporation of Tc(IV) within the goethite mineral lattice and subsequent goethite armoring can limit re-oxidation of Tc(IV) and its subsequent release from Tc-goethite waste forms, even when the final product is placed in oxidizing environments that typify shallow waste burial facilities.« less

Role of root exudates in dissolution of Cd containing iron oxides

NASA Astrophysics Data System (ADS)

Rosenfeld, C.; Martinez, C. E.

2011-12-01

Dissolved organic matter (DOM) in the rhizosphere contains organic acids, amino acids and more complex organic molecules that can substantially impact the solubility of soil solid phases. Plant roots and soil microorganisms contribute a large fraction of these organic compounds to DOM, potentially accelerating the transfer of solid phase elements into solution. In highly contaminated soils, heavy metals such as Cd are commonly found coprecipitated with common minerals (e.g. iron oxides). Introducing or changing vegetation on these contaminated soils may increase DOM levels in the soil pore fluids and thus enhance the biological and chemical weathering of soil minerals. Here, we investigate the role of root exudates on mineral dissolution and Cd mobility in contaminated soils. We hypothesize that plant exudates containing nitrogen and sulfur functional groups will dissolve Cd-containing mineral phases to a greater extent than exudates containing only oxygen functional groups, resulting in higher Cd concentrations in solution. Two different iron oxide mineral phases were utilized in a laboratory-scale model study system investigating the effects of low molecular weight, oxygen-, nitrogen-, and sulfur-containing organic compounds on mineral dissolution. Goethite (α-FeOOH) was synthesized in the laboratory with 0, 2.4, 5, and 100 theoretical mol% Cd, and franklinite (ZnFe2O4) was prepared with 0, 10, and 25 theoretical mol% Cd. Phase identity of all minerals was verified with X-ray diffraction (XRD). All minerals were reacted with 0.01 mM solutions containing one of four different organic ligands (oxalic acid, citric acid, histidine or cysteine) and aliquots of these solutions were sampled periodically over 40 days. Results from solution samples suggest that oxalic acid, citric acid, and histidine consistently increase mineral dissolution relative to the control (no organic compound present) while cysteine consistently inhibits dissolution relative to the control in all minerals. Increasing Cd substitution in the franklinite resulted in increased release of Fe and Zn to solution in the presence of these organic compounds, while increasing Cd substitution in the goethite generally limited Fe release to solution. In the case of cysteine, sulfur concentrations in solution decrease over time in the presence of Cd-containing minerals, indicating strong binding of the cysteine compound to the mineral surface, inhibiting Cd dissolution from the minerals. Our work indicates that amino acids present in biological soil exudates, in addition to organic acids, may have substantial impacts on iron oxide dissolution in soils, altering the availability of both bioessential (e.g., Fe and Zn) and non-essential, or potentially toxic, (e.g., Cd) elements.

Microstructure investigation on micropore formation in microporous silica materials prepared via a catalytic sol-gel process by small angle X-ray scattering.

PubMed

Shimizu, Wataru; Hokka, Junsuke; Sato, Takaaki; Usami, Hisanao; Murakami, Yasushi

2011-08-04

The so-called sol-gel technique has been shown to be a template-free, efficient way to create functional porous silica materials having uniform micropores. This appears to be closely linked with a postulation that the formation of weakly branched polymer-like aggregates in a precursor solution is a key to the uniform micropore generation. However, how such a polymer-like structure can precisely be controlled, and further, how the generated low-fractal dimension solution structure is imprinted on the solid silica materials still remain elusive. Here we present fabrication of microporous silica from tetramethyl orthosilicate (TMOS) using a recently developed catalytic sol-gel process based on a nonionic hydroxyacetone (HA) catalyst. Small angle X-ray scattering (SAXS), nitrogen adsorption porosimetry, and transmission electron microscope (TEM) allowed us to observe the whole structural evolution, ranging from polymer-like aggregates in the precursor solution to agglomeration with heat treatment and microporous morphology of silica powders after drying and hydrolysis. Using the HA catalyst with short chain monohydric alcohols (methanol or ethanol) in the precursor solution, polymer-like aggregates having microscopic correlation length (or mesh-size) < 2 nm and low fractal dimensions ∼2, which is identical to that of an ideal coil polymer, can selectively be synthesized, yielding the uniform micropores with diameters <2 nm in the solid materials. In contrast, the absence of HA or substitution of 1-propanol led to considerably different scattering behavior reflecting the particle-like aggregate formation in the precursor solution, which resulted in the formation of mesopores (diameter >2 nm) in the solid product due to apertures between the particle-like aggregates. The data demonstrate that the extremely fine porous silica architecture comes essentially from a gaussian polymer-like nature of the silica aggregates in the precursor having the microscopic mesh-size and their successful imprint on the solid product. The result offers a general but significantly efficient route to creating precisely designed fine porous silica materials under mild condition that serve as low refractive index and efficient thermal insulation materials in their practical applications.

Accounting for product substitution in the analysis of food taxes targeting obesity.

PubMed

Miao, Zhen; Beghin, John C; Jensen, Helen H

2013-11-01

We extend the existing literature on food taxes targeting obesity. We systematically incorporate the implicit substitution between added sugars and solid fats into a comprehensive food demand system and evaluate the effect of taxes on sugars and fats. The approach conditions how food and obesity taxes affect total calorie intake. The proposed methodology accounts for the ability of consumers to substitute leaner low-fat and low-sugar items for rich food items within the same food group. We calibrate this demand system approach using recent food intake data and existing estimates of price and income elasticities of demand. The demand system accounts for both the within-food group substitution and the substitution across these groups. Simulations of taxes on added sugars and solid fat show that the tax impact on consumption patterns is understated and the induced welfare loss is overstated when not allowing for the substitution possibilities within food groups. Copyright © 2012 John Wiley & Sons, Ltd.

Multi-stimuli responsive luminescent azepane-substituted β-diketones and difluoroboron complexes.

PubMed

Wang, Fang; DeRosa, Christopher A; Daly, Margaret L; Song, Daniel; Fraser, Cassandra L

2017-09-01

Difluoroboron β-diketonate (BF 2 bdk) compounds show environment-sensitive optical properties in solution, aggregation-induced emission (AIE) and multi-stimuli responsive fluorescence switching in the solid state. Here, a series of 4-azepane-substituted β-diketone (bdk) ligands ( L-H , L-OMe , L-Br ) and their corresponding difluoroboron dyes ( D-H , D-OMe , D-Br ) were synthesized, and various responsive fluorescence properties of the compounds were studied, including solvatochromism, viscochromism, AIE, mechanochromic luminescence (ML) and halochromism. Compared to the β-diketones, the boron complexes exhibited higher extinction coefficients but lower quantum yields, and red-shifted absorption and emission in CH 2 Cl 2 . Computational studies showed that intramolecular charge transfer (ICT) dominated rather than π-π* transitions in all the compounds regardless of boron coordination. In solution, all the bdk ligands and boron dyes showed red-shifted emission in more polar solvents and increased fluorescence intensity in more viscous media. Upon aggregation, the emission of the β-diketones was quenched, however, the boronated dyes showed increased emission, indicative of AIE. Solid-state emission properties, ML and halochromism, were investigated on spin cast films. For ML, smearing caused a bathochromic emission shift for L-Br , and powder X-ray diffraction (XRD) patterns showed that the "as spun" and thermally annealed states were more crystalline and the smeared state was amorphous. No obvious ML emission shift was observed for L-H or L-OMe , and the boronated dyes were not mechano-active. Trifluoroacetic acid (TFA) and triethylamine (TEA) vapors were used to study halochromism. Large hypsochromic emission shifts were observed for all the compounds after TFA vapor was applied, and reversible fluorescence switching was achieved using the acid/base pair.

Structural and {sup 31}P NMR investigation of Bi(MM'){sub 2}PO{sub 6} statistic solid solutions: Deconvolution of lattice constraints and cationic influences

DOE Office of Scientific and Technical Information (OSTI.GOV)

Colmont, Marie; Delevoye, Laurent; Ketatni, El Mostafa

2006-07-15

Two solid solutions BiM{sub x} Mg{sub (2-x)}PO{sub 6} (with M {sup 2+}=Zn or Cd) have been studied through {sup 31}P MAS NMR. The analysis has been performed on the basis of refined crystal structures through X-ray diffraction and neutron diffraction. The BiZn {sub x} Mg{sub (2-x)}PO{sub 6} does not provide direct evidence for sensitive changes in the phosphorus local symmetry. This result is in good agreement with structural data which show nearly unchanged lattices and atomic separations through the Zn{sup 2+} for Mg{sup 2+} substitution. On the other hand, the Cd{sup 2+} for Mg{sup 2+} substitution behaves differently. Indeed, upmore » to five resonances are observed, each corresponding to one of the five first-cationic neighbour distributions, i.e. 4Mg/0Cd, 3Mg/1Cd, 2Mg/2Cd, 1Mg/3Cd and 0Mg/4Cd. Their intensities match rather well the expected weight for each configuration of the statistical Cd{sup 2+}/Mg{sup 2+} mixed occupancy. The match is further improved when one takes into account the influence of the 2nd cationic sphere that is available from high-field NMR data (18.8 T). Finally, the fine examination of the chemical shift for each resonance versus x allows to de-convolute the mean Z/a {sup 2} effective field into two sub-effects: a lattice constraint-only term and a chemical-only term whose effects are directly quantifiable. - Graphical abstract: First (CdMg){sub 4} cationic sphere influence on the {sup 31}P NMR signal in Bi(Cd,Mg){sub 2}PO{sub 6}. Display Omitted.« less

Spin-glass behavior of Sn{sub 0.9}Fe{sub 3.1}N: An experimental and quantum-theoretical study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scholz, Tanja; Dronskowski, Richard, E-mail: drons@HAL9000.ac.rwth-aachen.de

Based on comprehensive experimental and quantum-theoretical investigations, we identify Sn{sub 0.9}Fe{sub 3.1}N as a canonical spin glass and the first ternary iron nitride with a frustrated spin ground state. Sn{sub 0.9}Fe{sub 3.1}N is the end member of the solid solution Sn{sub x}Fe{sub 4−x}N (0 < x ≤ 0.9) derived from ferromagnetic γ′-Fe{sub 4}N. Within the solid solution, the gradual incorporation of tin is accompanied by a drastic weakening of the ferromagnetic interactions. To explore the dilution of the ferromagnetic coupling, the highly tin-substituted Sn{sub 0.9}Fe{sub 3.1}N has been magnetically reinvestigated. DC magnetometry reveals diverging susceptibilities for FC and ZFC measurementsmore » at low temperatures and an unsaturated hysteretic loop even at high magnetic fields. The temperature dependence of the real component of the AC susceptibility at different frequencies proves the spin-glass transition with the characteristic parameters T{sub g}  =  12.83(6) K, τ{sup *} = 10{sup −11.8(2)} s, zv = 5.6(1) and ΔT{sub m}/(T{sub m} ⋅ Δlgω) = 0.015. The time-dependent response of the magnetic spins to the external field has been studied by extracting the distribution function of relaxation times g(τ, T) up to T{sub g} from the complex plane of AC susceptibilities. The weakening of the ferromagnetic coupling by substituting tin into γ′-Fe{sub 4}N is explained by the Stoner criterion on the basis of electronic structure calculations and a quantum-theoretical bonding analysis.« less

Dy3TaO7, A stoichiometric spin glass and the effect of disorder via chemical substitution in the Dy3-xYxTaO7 (0 ≤ x ≤ 3) solid solution

NASA Astrophysics Data System (ADS)

Gómez-García, J. Francisco; Bucio, Lauro; Tavizon, Gustavo

2018-01-01

In this work, we present both structural and magnetic (DC magnetization and AC susceptibility) studies of the Dy3-xYxTaO7 solid solution. The structural characterization of samples was performed by Rietveld refinements of the X-ray diffraction data. All compounds crystallized in a weberite-related structure in the orthorhombic C2221 space group (No. 20); the variations of the lattice parameters obey the Vegard´s law in the whole range of composition. DC magnetic measurements of the Dy3-xYxTaO7 system showed a Curie-Weiss paramagnetic behaviour, with antiferromagnetic interactions at T>150 K. Below 3 K a spin glass behaviour in the 0 ≤ x ≤ 1 range of the solid solution was observed. The stoichiometric Dy3TaO7 compound showed spin glass behaviour although there is no evidence of structural disorder. For some Y3+ doped compounds (x = 0.33, 0.66 and 1.0), chemical disorder reduced the freezing temperature (Tg) values with a ×1/3 dependence. Cole-Cole analysis of the AC magnetic field response showed similar phenomenological parameters for the stoichiometric (x = 0) and the Y3+ doped compounds with spin glassiness, suggesting an analogous mechanism for these compounds. For the Dy3-xYxTaO7 system, in which the spin glass behaviour seems to exhibit a critical concentration, a magnetic phase diagram is proposed.

Synergistic Strategy to Enhance the Thermoelectric Properties of CoSbS1-xSex Compounds via Solid Solution.

PubMed

Yao, Wei; Yang, Dingfeng; Yan, Yanci; Peng, Kunling; Zhan, Heng; Liu, Anping; Lu, Xu; Wang, Guoyu; Zhou, Xiaoyuan

2017-03-29

High thermal conductivity of CoSbS-based limited its own prospect application in thermoelectric energy conversion. Solid solution is an effective approach to optimize the performance of thermoelectric materials with high lattice thermal conductivity because of the enhanced phonons scattering from disorder atoms. In this paper, we have synthesized and measured the thermoelectric properties of solid solution CoSbS 1-x Se x (x = 0, 0.05, 0.10, 0.15, 0.20, 0.30) series samples. The collaborative optimization (enhancing the power factors and reducing the thermal conductivities) to add zT values were realized via substitution of S atoms with the isoelectronic Se atoms in the matrix. Meanwhile, the lowest room temperature lattice thermal conductivity in CoSbS-based materials is obtained (4.72 W m -1 K -1 ) at present. Benefiting from the results of synergistic strategy, a zT of 0.35 was achieved at 923 K for sample CoSbS 0.85 Se 0.15 , a 59% improvement as compared with that of the pristine CoSbS. Band calculation demonstrated that CoSbS 0.85 Se 0.15 present a similar band dispersion with CoSbS. The mechanism of point defect scattering for reducing the lattice thermal conductivity at room temperature, was also analyzed by the Callaway model. The contributions to decrease the room temperature lattice thermal conductivity from the mass and the strain fluctuation in the crystal are comparable. These results can also be extended to other high-efficiency thermoelectric materials with stiff bond and smaller Gruneisen parameters.

2Flux growth and characterization of Ce-substituted Nd 2 Fe 14 B single crystals

DOE PAGES

Susner, Michael A.; Conner, Benjamin S.; Saparov, Bayrammurad I.; ...

2016-10-27

Single crystals of (Nd 1-xCe x) 2Fe 14B are grown out of Fe-(Nd,Ce) flux. Chemical and structural analysis of the crystals indicate that (Nd 1-xCe x) 2Fe 14B forms a solid solution until at least x = 0.38 with a Vegard-like variation of the lattice constants with x. Refinements of single crystal neutron diffraction data indicate that Ce has a slight site preference (7:3) for the 4g rare earth site over the 4f site. Magnetization measurements at 300 K show only small decreases with increasing Ce content in saturation magnetization (M s) and anisotropy field (H A), and Curie temperaturemore » (T C). First principles calculations are carried out to understand the effect of Ce substitution on the electronic and magnetic properties. For a multitude of applications, it is expected that the advantage of incorporating lower-cost and more abundant Ce will outweigh the small adverse effects on magnetic properties. In conclusion, Ce-substituted Nd 2Fe 14B is therefore a potential high-performance permanent magnet material with substantially reduced Nd content.« less

Arsenic uptake by gypsum and calcite: Modelling and probing by neutron and X-ray scattering

NASA Astrophysics Data System (ADS)

Fernández-Martínez, A.; Román-Ross, G.; Cuello, G. J.; Turrillas, X.; Charlet, L.; Johnson, M. R.; Bardelli, F.

2006-11-01

Uptaking of contaminants by solid phases is relevant to many issues in environmental science as this process can remove them from solutions and retard their transport into the hydrosphere. Here we report on two structural studies performed on As-doped gypsum (CaSO 4 2H 2O) and calcite (CaCO 3), using neutron (D20-ILL) and X-ray (ID11-ESRF) diffraction data and EXAFS (BM8-ESRF). The aim of this study is to determine whether As gets into the bulk of gypsum and calcite structures or is simply adsorbed on the surface. Different mechanisms of substitution are used as hypotheses. The combined Rietveld analysis of neutron and X-ray diffraction data shows an expansion of the unit cell volume proportional to the As concentration within the samples. DFT-based simulations confirm the increase of the unit cell volume proportional to the amount of carbonate or sulphate groups substituted. Interpolation of the experimental Rietveld data allows us to distinguish As substituted within the structure from that adsorbed on the surface of both minerals. Results obtained by EXAFS analysis from calcite samples show good agreement with the hypothesis of replacement of As into the C crystallographic site.

Behaviour of Fe4O5-Mg2Fe2O5 solid solutions and their relation to coexisting Mg-Fe silicates and oxide phases

NASA Astrophysics Data System (ADS)

Uenver-Thiele, Laura; Woodland, Alan B.; Miyajima, Nobuyoshi; Ballaran, Tiziana Boffa; Frost, Daniel J.

2018-03-01

Experiments at high pressures and temperatures were carried out (1) to investigate the crystal-chemical behaviour of Fe4O5-Mg2Fe2O5 solid solutions and (2) to explore the phase relations involving (Mg,Fe)2Fe2O5 (denoted as O5-phase) and Mg-Fe silicates. Multi-anvil experiments were performed at 11-20 GPa and 1100-1600 °C using different starting compositions including two that were Si-bearing. In Si-free experiments the O5-phase coexists with Fe2O3, hp-(Mg,Fe)Fe2O4, (Mg,Fe)3Fe4O9 or an unquenchable phase of different stoichiometry. Si-bearing experiments yielded phase assemblages consisting of the O5-phase together with olivine, wadsleyite or ringwoodite, majoritic garnet or Fe3+-bearing phase B. However, (Mg,Fe)2Fe2O5 does not incorporate Si. Electron microprobe analyses revealed that phase B incorporates significant amounts of Fe2+ and Fe3+ (at least 1.0 cations Fe per formula unit). Fe-L2,3-edge energy-loss near-edge structure spectra confirm the presence of ferric iron [Fe3+/Fetot = 0.41(4)] and indicate substitution according to the following charge-balanced exchange: [4]Si4+ + [6]Mg2+ = 2Fe3+. The ability to accommodate Fe2+ and Fe3+ makes this potential "water-storing" mineral interesting since such substitutions should enlarge its stability field. The thermodynamic properties of Mg2Fe2O5 have been refined, yielding H°1bar,298 = - 1981.5 kJ mol- 1. Solid solution is complete across the Fe4O5-Mg2Fe2O5 binary. Molar volume decreases essentially linearly with increasing Mg content, consistent with ideal mixing behaviour. The partitioning of Mg and Fe2+ with silicates indicates that (Mg,Fe)2Fe2O5 has a strong preference for Fe2+. Modelling of partitioning with olivine is consistent with the O5-phase exhibiting ideal mixing behaviour. Mg-Fe2+ partitioning between (Mg,Fe)2Fe2O5 and ringwoodite or wadsleyite is influenced by the presence of Fe3+ and OH incorporation in the silicate phases.

A new ferroelectric solid solution system of LaCrO 3-BiCrO 3

NASA Astrophysics Data System (ADS)

Chen, J. I. L.; Kumar, M. Mahesh; Ye, Z.-G.

2004-04-01

A new perovskite solid solution system of (1- x)LaCrO 3- xBiCrO 3 has been prepared by conventional solid-state reaction and sintering processes at 1200°C in a sealed Pt tube or a Bi 2O 3-rich environment. A clean orthorhombic phase of LaCrO 3-type structure is established at room temperature for compositions with 0⩽ x⩽0.35. The relative density, lattice parameters, sintering mechanism, microstructure and ferroelectricity of the compounds are investigated. The substitution of Bi 2O 3 for La 2O 3 is found to decrease the unit cell volume and increase the grain size of the ceramics. The relative density of the ceramics sintered at 1200°C is significantly improved from 40% for LaCrO 3 up to about 90% for La 0.65Bi 0.35CrO 3 through a liquid phase sintering mechanism. The ferroelectricity is revealed in La 1- xBi xCrO 3 with 0.1⩽ x⩽0.35 by dielectric hysteresis loops displayed at 77 K. The remnant polarization is found to increase with increasing Bi 3+ content. The origin of the ferroelectricity is attributed to the structural distortion induced by the stereochemically active Bi 3+ ion on the A site.

Energetics and Defect Interactions of Complex Oxides for Energy Applications

NASA Astrophysics Data System (ADS)

Solomon, Jonathan Michael

The goal of this dissertation is to employ computational methods to gain greater insights into the energetics and defect interactions of complex oxides that are relevant for today's energy challenges. To achieve this goal, the development of novel computational methodologies are required to handle complex systems, including systems containing nearly 650 ions and systems with tens of thousands of possible atomic configurations. The systems that are investigated in this dissertation are aliovalently doped lanthanum orthophosphate (LaPO4) due to its potential application as a proton conducting electrolyte for intermediate temperature fuel cells, and aliovalently doped uranium dioxide (UO2) due to its importance in nuclear fuel performance and disposal. First we undertake density-functional-theory (DFT) calculations on the relative energetics of pyrophosphate defects and protons in LaPO4, including their binding with divalent dopant cations. In particular, for supercell calculations with 1.85 mol% Sr doping, we investigate the dopant-binding energies for pyrophosphate defects to be 0.37 eV, which is comparable to the value of 0.34 eV calculated for proton-dopant binding energies in the same system. These results establish that dopant-defect interactions further stabilize proton incorporation, with the hydration enthalpies when the dopants are nearest and furthest from the protons and pyrophosphate defects being -1.66 eV and -1.37 eV, respectively. Even though our calculations show that dopant binding enhances the enthalpic favorability of proton incorporation, they also suggest that such binding is likely to substantially lower the kinetic rate of hydrolysis of pyrophosphate defects. We then shift our focus to solid solutions of fluorite-structured UO 2 with trivalent rare earth fission product cations (M3+=Y, La) using a combination of ionic pair potential and DFT based methods. Calculated enthalpies of formation with respect to constituent oxides show higher energetic stability for La solid solutions than for Y. Additionally, calculations performed for different atomic configurations show a preference for reduced (increased) oxygen vacancy coordination around La (Y) dopants. The current results are shown to be qualitatively consistent with related calculations and calorimetric measurements of heats of formation in other trivalent doped fluorite oxides, which show a tendency for increasing stability and increasing preference for higher oxygen coordination with increasing size of the trivalent impurity. We expand this investigation by considering a series of trivalent rare earth fission product cations, specifically, Y3+ (1.02 A, Shannon radius with eightfold coordination), Dy3+ (1.03 A), Gd 3+ (1.05 A), Eu3+ (1.07 A), Sm3+ (1.08 A), Pm3+ (1.09 A), Nd3+ (1.11 A), Pr3+ (1.13 A), Ce3+ (1.14 A) and La3+ (1.16 A). Compounds with ionic radius of the M3+ species smaller or larger than 1.09 A are found to have energetically preferred defect ordering arrangements. Systems with preferred defect ordering arrangements are suggestive of defect clustering in short range ordered solid solutions, which is expected to limit oxygen ion mobility and therefore the rate of oxidation of spent nuclear fuel. Finally, the energetics of rare earth substituted (M3+= La, Y, and Nd) UO2 solid solutions are investigated by employing a combination of calorimetric measurements and DFT based computations. The calorimetric studies are performed by Lei Zhang and Professor Alexandra Navrotsky at the University of Calfornia, Davis, as part of a joint computational/ experimental collaborative effort supported through the Materials Science of Actinides Energy Frontier Research Center. Calculated and measured formation enthalpies agree within 10 kJ/mol for stoichiometric oxygen/metal compositions. To better understand the factors governing the stability and defect binding in rare earth substituted urania solid solutions, systematic trends in the energetics are investigated based on the present results and previous computational and experimental thermochemical studies of rare earth substituted fluorite oxides. A consistent trend towards increased energetic stability with larger size mismatch between the smaller host tetravalent cation and the larger rare earth trivalent cation is found for both actinide and non-actinide fluorite oxide systems where aliovalent substitution of M cations is compensated by oxygen vacancies. However, the large exothermic oxidation enthalpy in the UO2 based systems favors compositions with higher oxygen-to-metal ratios where charge compensation occurs through the formation of uranium cations with higher oxidation states.

Crystal structure and europium luminescence of NaMgH3-xFx

NASA Astrophysics Data System (ADS)

Pflug, Christian; Franz, Alexandra; Kohlmann, Holger

2018-02-01

The solid solution series NaMgH3-xFx (x = 0, 0.5, 1, 1.5, 2, 2.5, 3) was synthesized by solid-state reactions under hydrogen gas pressure from binary ionic hydrides, fluorides and magnesium. Rietveld refinement based on X-ray powder diffraction data revealed the GdFeO3-structure type for all compounds and a trend of lattice parameters according to Vegard's law. The anion distribution in NaMgD2F and NaMgD1.5F1.5 was found to be statistical by Rietveld refinement based on neutron powder diffraction data. Photoluminescence measurements on europium(II) substituted NaMgH3-xFx revealed a strong red shift of the emission wavelength (λem = 665 nm for NaMgH2F:Eu) in comparison to violet emitting NaMgF3:Eu.

Photochemistry and Transmission Pump-Probe Spectroscopy of 2-Azidobiphenyls in Aqueous Nanocrystalline Suspensions: Simplified Kinetics in Crystalline Solids.

PubMed

Chung, Tim S; Ayitou, Anoklase J-L; Park, Jin H; Breslin, Vanessa M; Garcia-Garibay, Miguel A

2017-04-20

Aqueous nanocrystalline suspensions provide a simple and efficient medium for performing transmission spectroscopy measurements in the solid state. In this Letter we describe the use of laser flash photolysis methods to analyze the photochemistry of 2-azidobiphenyl and several aryl-substituted derivatives. We show that all the crystalline compounds analyzed in this study transform quantitatively into carbazole products via a crystal-to-crystal reconstructive phase transition. While the initial steps of the reaction cannot be followed within the time resolution of our instrument (ca. 8 ns), we detected the primary isocarbazole photoproducts and analyzed the kinetics of their formal 1,5-H shift reactions, which take place in time scales that range from a few nanoseconds to several microseconds. It is worth noting that the high reaction selectivity observed in the crystalline state translates into a clean and simple kinetic process compared to that in solution.

Development of new materials and structures based on managed physical-chemical factors of local interaction

NASA Astrophysics Data System (ADS)

Urakov, A. L.

2016-04-01

The paper states that assigning certain physical and chemical characteristics to pills and medical drugs solutions can substitute for the development of new drugs (which is essentially equivalent to the creation of new medicines). It is established that the purposeful change of physical and chemical characteristics of the standard ("old") materials (in other words, the known substances) is fundamental for the production of solid and liquid medicines, which allows us to get "new" structures and materials. The paper shows that assigning new physical and chemical properties to "old" materials and their further usage for the production of tablets and solutions from the "old" and well-known medicines can turn even very "old" medicine into very "novel" (moreover, even very fashionable) one with unprecedented (fantastic) pharmacological activity and new mechanisms of action.

2,5-difluorenyl-substituted siloles for the fabrication of high-performance yellow organic light-emitting diodes.

PubMed

Chen, Bin; Jiang, Yibin; Chen, Long; Nie, Han; He, Bairong; Lu, Ping; Sung, Herman H Y; Williams, Ian D; Kwok, Hoi Sing; Qin, Anjun; Zhao, Zujin; Tang, Ben Zhong

2014-02-10

2,3,4,5-Tetraarylsiloles are a class of important luminogenic materials with efficient solid-state emission and excellent electron-transport capacity. However, those exhibiting outstanding electroluminescence properties are still rare. In this work, bulky 9,9-dimethylfluorenyl, 9,9-diphenylfluorenyl, and 9,9'-spirobifluorenyl substituents were introduced into the 2,5-positions of silole rings. The resulting 2,5-difluorenyl-substituted siloles are thermally stable and have low-lying LUMO energy levels. Crystallographic analysis revealed that intramolecular π-π interactions are prone to form between 9,9'-spirobifluorene units and phenyl rings at the 3,4-positions of the silole ring. In the solution state, these new siloles show weak blue and green emission bands, arising from the fluorenyl groups and silole rings with a certain extension of π conjugation, respectively. With increasing substituent volume, intramolecular rotation is decreased, and thus the emissions of the present siloles gradually improved and they showed higher fluorescence quantum yields (Φ(F) =2.5-5.4%) than 2,3,4,5-tetraphenylsiloles. They are highly emissive in solid films, with dominant green to yellow emissions and good solid-state Φ(F) values (75-88%). Efficient organic light-emitting diodes were fabricated by adopting them as host emitters and gave high luminance, current efficiency, and power efficiency of up to 44,100 cd m(-2), 18.3 cd A(-1), and 15.7 lm W(-1), respectively. Notably, a maximum external quantum efficiency of 5.5% was achieved in an optimized device. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

In Situ Tracking Kinetic Pathways of Li + /Na + Substitution during Ion-Exchange Synthesis of Li xNa 1.5–x VOPO 4 F 0.5

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, Young-Uk; Bai, Jianming; Wang, Liping

Ion exchange is a ubiquitous phenomenon central to wide industrial applications, ranging from traditional (bio)chemical separation to the emerging chimie douce synthesis of materials for batteries and other energy applications. The exchange process is complex, involving substitution and transport of different ions under non-equilibrium conditions, and thus difficult to probe, leaving a gap in mechanistic understanding of kinetic exchange pathways toward final products. Herein, we report in situ tracking kinetic pathways of Li +/Na + substitution during solvothermal ion-exchange synthesis of Li xNa 1.5-xVOPO 4F 0.5 (0 ≤ x ≤ 1.5), a promising multi-Li polyanionic cathode for batteries. The real-timemore » observation, corroborated by first-principles calculations, reveals a selective replacement of Na + by Li +, leading to peculiar Na +/Li +/vacancy orderings in the intermediates. Contradicting the traditional belief of facile topotactic substitution via solid solution reaction, an abrupt two-phase transformation occurs and predominantly governs the kinetics of ion exchange and transport in the 1D polyanionic framework, consequently leading to significant difference of Li stoichiometry and electrochemical properties in the exchanged products. The findings may help to pave the way for rational design of ion exchange synthesis for making new materials.« less

In Situ Tracking Kinetic Pathways of Li + /Na + Substitution during Ion-Exchange Synthesis of Li xNa 1.5–x VOPO 4 F 0.5

DOE PAGES

Park, Young-Uk; Bai, Jianming; Wang, Liping; ...

2017-08-29

Ion exchange is a ubiquitous phenomenon central to wide industrial applications, ranging from traditional (bio)chemical separation to the emerging chimie douce synthesis of materials for batteries and other energy applications. The exchange process is complex, involving substitution and transport of different ions under non-equilibrium conditions, and thus difficult to probe, leaving a gap in mechanistic understanding of kinetic exchange pathways toward final products. Herein, we report in situ tracking kinetic pathways of Li +/Na + substitution during solvothermal ion-exchange synthesis of Li xNa 1.5-xVOPO 4F 0.5 (0 ≤ x ≤ 1.5), a promising multi-Li polyanionic cathode for batteries. The real-timemore » observation, corroborated by first-principles calculations, reveals a selective replacement of Na + by Li +, leading to peculiar Na +/Li +/vacancy orderings in the intermediates. Contradicting the traditional belief of facile topotactic substitution via solid solution reaction, an abrupt two-phase transformation occurs and predominantly governs the kinetics of ion exchange and transport in the 1D polyanionic framework, consequently leading to significant difference of Li stoichiometry and electrochemical properties in the exchanged products. The findings may help to pave the way for rational design of ion exchange synthesis for making new materials.« less

Automated electrochemical synthesis and photoelectrochemical characterization of Zn1-xCo(x)O thin films for solar hydrogen production.

PubMed

Jaramillo, Thomas F; Baeck, Sung-Hyeon; Kleiman-Shwarsctein, Alan; Choi, Kyoung-Shin; Stucky, Galen D; McFarland, Eric W

2005-01-01

High-throughput electrochemical methods have been developed for the investigation of Zn1-xCo(x)O films for photoelectrochemical hydrogen production from water. A library of 120 samples containing 27 different compositions (0

Synthesis and characterisation of the hollandite solid solution Ba1.2-xCsxFe2.4-xTi5.6+xO16 for partitioning and conditioning of radiocaesium

NASA Astrophysics Data System (ADS)

Bailey, Daniel J.; Stennett, Martin C.; Mason, Amber R.; Hyatt, Neil C.

2018-05-01

The geological disposal of high level radioactive waste requires careful budgeting of the heat load produced by radiogenic decay. Removal of high-heat generating radionuclides, such as 137Cs, reduces the heat load in the repository allowing the remaining high level waste to be packed closer together therefore reducing demand for repository space and the cost of the disposal of the remaining wastes. Hollandites have been proposed as a possible host matrix for the long-term disposal of Cs separated from HLW raffinate. The incorporation of Cs into the hollandite phase is aided by substitution of cations on the B-site of the hollandite structure, including iron. A range of Cs containing iron hollandites were synthesised via an alkoxide-nitrate route and the structural environment of Fe in the resultant material characterised by Mössbauer and X-ray Absorption Near Edge Spectroscopy. The results of spectroscopic analysis found that Fe was present as octahedrally co-ordinated Fe (III) in all cases and acts as an effective charge compensator over a wide solid solution range.

Synthesis, Rietveld refinements, Infrared and Raman spectroscopy studies of the sodium diphosphate NaCryFe1-yP2O7 (0 ≤ y ≤ 1)

NASA Astrophysics Data System (ADS)

Bih, H.; Saadoune, I.; Bih, L.; Mansori, M.; ToufiK, H.; Fuess, H.; Ehrenberg, H.

2016-01-01

In the present study we report on the synthesis and crystal structure studies of NaCryFe1-yP2O7 sodium diphosphate solid solution (0 ≤ y ≤ 1). The X-ray diffraction shows that these compounds are isostructural with NaFeP2O7 and NaCrP2O7 (space group P21/c (C2h5) Z = 4). The Rietveld refinements based on the XRD patterns show the existence of a continuous solid solution over the whole composition range (0 ≤ y ≤ 1). A continuous evolution of the monoclinic unit cell parameters was obtained. The transition metal ions (Cr3+ and/or Fe3+) connect the diphosphate anions forming a three-dimensional network with cages filled by Na+ cations. IR and Raman spectra have been interpreted using factor group analysis. A small shift of the band frequencies is observed when Fe is substituted by Cr. The POP bridge angles are determined from Lazarev's relation and agree well with those deduced from the crystal structure refinement.

Optical limiting materials

DOEpatents

McBranch, D.W.; Mattes, B.R.; Koskelo, A.C.; Heeger, A.J.; Robinson, J.M.; Smilowitz, L.B.; Klimov, V.I.; Cha, M.; Sariciftci, N.S.; Hummelen, J.C.

1998-04-21

Methanofullerenes, fulleroids and/or other fullerenes chemically altered for enhanced solubility, in liquid solution, and in solid blends with transparent glass (SiO{sub 2}) gels or polymers, or semiconducting (conjugated) polymers, are shown to be useful as optical limiters (optical surge protectors). The nonlinear absorption is tunable such that the energy transmitted through such blends saturates at high input energy per pulse over a wide range of wavelengths from 400--1,100 nm by selecting the host material for its absorption wavelength and ability to transfer the absorbed energy into the optical limiting composition dissolved therein. This phenomenon should be generalizable to other compositions than substituted fullerenes. 5 figs.

Optical limiting materials

DOEpatents

McBranch, Duncan W.; Mattes, Benjamin R.; Koskelo, Aaron C.; Heeger, Alan J.; Robinson, Jeanne M.; Smilowitz, Laura B.; Klimov, Victor I.; Cha, Myoungsik; Sariciftci, N. Serdar; Hummelen, Jan C.

1998-01-01

Optical limiting materials. Methanofullerenes, fulleroids and/or other fullerenes chemically altered for enhanced solubility, in liquid solution, and in solid blends with transparent glass (SiO.sub.2) gels or polymers, or semiconducting (conjugated) polymers, are shown to be useful as optical limiters (optical surge protectors). The nonlinear absorption is tunable such that the energy transmitted through such blends saturates at high input energy per pulse over a wide range of wavelengths from 400-1100 nm by selecting the host material for its absorption wavelength and ability to transfer the absorbed energy into the optical limiting composition dissolved therein. This phenomenon should be generalizable to other compositions than substituted fullerenes.

KMg0.09Fe1.91(PO4)2

PubMed Central

Yatskin, Michael M.; Zatovsky, Igor V.; Baumer, Vyacheslav N.; Ogorodnyk, Ivan V.; Slobodyanik, Nikolay S.

2012-01-01

KMg0.09Fe1.91(PO4)2, potassium [iron(II)/magnesium] iron(III) bis(orthophosphate), is a solid solution derived from compounds with general formula KM IIFe(PO4)2 (M II = Fe, Cu), in which the Mg atoms substitute Fe atoms only in the octa­hedrally surrounded sites. The framework of the structure is built up from [FeO5] trigonal bipyramids and [MO6] (M = (Fe, Mg) octa­hedra sharing corners and edges and connected by two types of bridging PO4 tetra­hedra. The K+ cations are nine-coordinated and are situated in channels running along [101]. PMID:22719280

Thermodynamic Stability of Transition Metal Substituted LiMn 2-xMxO 4 (M=Cr, Fe, Co, and Ni) Spinels

NASA Astrophysics Data System (ADS)

Lai, Chenying

The formation enthalpies from binary oxides of LiMn2O 4, LiMn2-xCrxO4 (x = 0.25, 0.5, 0.75 and 1), LiMn2-xFexO4 (x = 0.25 and 0.5), LiMn2-xCoxO4 (x = 0.25, 0.5, and 0.75) and LiMn1.75Ni 0.25O4 at 25 °C have been measured by high-temperature oxide-melt-solution calorimetry and were found to be strongly exothermic. Increasing Cr, Co and Ni content leads to more thermodynamically stable spinels, but increasing Fe content does not significantly affect the stability. The formation enthalpies from oxides of the fully substituted spinels, LiMnMO 4 (M = Cr, Fe and Co) become more exothermic (implying increasing stability) with decreasing ionic radius of the metal and lattice parameters of the spinel. The trend in enthalpy versus metal content is roughly linear, suggesting a close-to-zero heat of mixing in LiMn2O4 - LiMnMO 4 solid solutions. These data confirm that transition metal doping is beneficial for stabilizing these potential cathode materials for lithium-ion batteries.

A green-yellow emitting oxyfluoride solid solution phosphor Sr[subscript 2]Ba(AlO[subscript 4]F)[subscript 1;#8722;x](SiO[subscript 5])x:Ce[superscript 3+] for thermally stable, high color rendition solid state white lighting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Denault, Kristin A.; George, Nathan C.; Paden, Sara R.

2012-10-23

A near-UV excited, oxyfluoride phosphor solid solution Sr{sub 1.975}Ce{sub 0.025}Ba(AlO{sub 4}F){sub 1-x}(SiO{sub 5}){sub x} has been developed for solid state white lighting applications. An examination of the host lattice, and the local structure around the Ce{sup 3+} activator ions through a combination of density functional theory, synchrotron X-ray and neutron powder diffraction and total scattering, and electron paramagnetic resonance, points to how chemical substitutions play a crucial role in tuning the optical properties of the phosphor. The maximum emission wavelength can be tuned from green ({lambda}{sub em} = 523 nm) to yellow ({lambda}{sub em} = 552 nm) by tuning themore » composition, x. Photoluminescent quantum yield is determined to be 70 {+-} 5% for some of the examples in the series. Excellent thermal properties were found for the x = 0.5 sample, with the photoluminescence intensity at 160 C only decreased to 82% of its room temperature value. Phosphor-converted LED devices fabricated using an InGaN LED ({lambda}{sub max} = 400 nm) exhibit high color rendering white light with R{sub a} = 70 and a correlated color temperature near 7000 K. The value of R{sub a} could be raised to 90 by the addition of a red component, and the correlated color temperature lowered to near 4000 K.« less

Enhancement of Ce/Cr Codopant Solubility and Chemical Homogeneity in TiO2 Nanoparticles through Sol-Gel versus Pechini Syntheses.

PubMed

Chen, Wen-Fan; Mofarah, Sajjad S; Hanaor, Dorian Amir Henry; Koshy, Pramod; Chen, Hsin-Kai; Jiang, Yue; Sorrell, Charles Christopher

2018-06-18

Ce/Cr codoped TiO 2 nanoparticles were synthesized using sol-gel and Pechini methods with heat treatment at 400 °C for 4 h. A conventional sol-gel process produced well-crystallized anatase, while Pechini synthesis yielded less-ordered mixed-phase anatase + rutile; this suggests that the latter method enhances Ce solubility and increases chemical homogeneity but destabilizes the TiO 2 lattice. Greater structural disruption from the decomposition of the Pechini precursor formed more open agglomerated morphologies, while the lower levels of structural disruption from pyrolysis of the dried sol-gel precursor resulted in denser agglomerates of lower surface areas. Codoping and associated destabilization of the lattice reduced the binding energies in both powders. Cr 4+ formation in sol-gel powders and Cr 6+ formation in Pechini powders suggest that these valence changes derive from synergistic electron exchange from intervalence and/or multivalence charge transfer. Since Ce is too large to allow either substitutional or interstitial solid solubility, the concept of integrated solubility is introduced, in which the Ti site and an adjacent interstice are occupied by the large Ce ion. The photocatalytic performance data show that codoping was detrimental owing to the effects of reduced crystallinity from lattice destabilization and surface area. Two regimes of mechanistic behavior are seen, which are attributed to the unsaturated solid solutions at lower codopant levels and supersaturated solid solutions at higher levels. The present work demonstrates that the Pechini method offers a processing technique that is superior to sol-gel because the former facilitates solid solubility and consequent chemical homogeneity.

Luminescent substituted fluoranthenes - synthesis, structure, electrochemical and optical properties.

PubMed

Slodek, Aneta; Maroń, Anna; Pająk, Michał; Matussek, Marek; Grudzka-Flak, Iwona; Małecki, Jan Grzegorz; Świtlicka, Anna; Krompiec, Stanisław; Danikiewicz, Witold; Grela, Małgorzata; Gryca, Izabela; Penkala, Mateusz

2018-04-16

Six novel fluoranthene derivatives, three terminally substituted and three bis(fluoranthenes) with fluorene, bithiophene and carbazole spacers were obtained via [2+2+2] cycloaddition and thoroughly characterized. Based on the conducted studies, the obtained derivatives can be classified as D-A (donor-acceptor) and A-D-A (acceptor-donor-acceptor) systems, where fluoranthene unit acts as an electron-withdrawing unit. The optical results revealed that novel fluoranthene derivatives absorb light in the range of 236-417 nm originating from ππ* transition within the conjugated system. The compounds exhibit fluorescence ranging from deep blue to green originating mainly from intramolecular charge transfer (ICT) states. The high Stoke shifts, high quantum yield in solution (φ= 0.22-0.57) and in the solid state (φ= 0.18-0.44) have been observed for fluoranthene derivatives. All derivatives possess multi-step oxidations at low potentials. The electronic structure of presented compounds is additionally supported by TD-DFT computations. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Influence of cobalt, tantaum and tungsten on the high temperature mechanical properties of single crystal nickel-base superalloys. Ph.D. Thesis - Case Western Reserve Univ.

NASA Technical Reports Server (NTRS)

Nathal, M. V.

1984-01-01

For alloys with the baseline refractory metal level of 3 percent Ta and 10 percent W, decreases in Co level from 10 to 0 percent resulted in increased tensile strength and creep resistance. Substitution of W for Ta resulted in decreased creep life at high stresses but improved life at low stresses. Substitution of Ni for Ta caused large reductions in tensile strength and creep resistance, and corresponding increases in ductility. For these alloys with low Ta plus W totals, strength was independent of Co level. The increases in tensile strength with increases in refractory metal content were related to the increases in gamma volume fraction and solid solution hardening. Increases in strength as Co level decreased were considered to be the result of coherency strain hardening from the increased lattice mismatch. Dislocation shear through the gamma-gamma interface is considered to be the rate limiting step in the deformation process.

Investigation of the phase relations in the U-Al-Ge ternary system: Influence of the Al/Ge substitution on the properties of the intermediate phases

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moussa, C.; El Sayah, Z.; Chajewski, G.

The phase relations within the U-Al-Ge ternary system were studied for two isothermal sections, at 673 K for the whole Gibbs triangle and at 1173 K for the concentration range 25–100 at% U. The identification of the phases, their composition ranges and stability were determined by x-ray powder diffraction, scanning electron microscopy coupled to energy dispersive spectroscopy and differential thermal analysis. The tie-lines and the solubility domains were determined for the U-Ge and U-Al binaries, the UAl{sub 3}-UGe{sub 3} solid-solution and for the unique ternary intermediate phase U{sub 3}Al{sub 2−x}Ge{sub 3+x}. The experimental isopleth section of the pseudo-binary UAl{sub 3}-UGe{submore » 3} reveals an isomorphous solid solution based on the Cu{sub 3}Au-type below the solidus. The U{sub 3}Al{sub 2−x}Ge{sub 3+x} solid solution extends for −0.1≤x≤1.35 and −0.2≤x≤1.5 at 673 K and 1173 K respectively. It crystallizes in the I-centered tetragonal symmetry. The reciprocal lattice of several compositions of the U{sub 3}Al{sub 2−x}Ge{sub 3+x} solid solution was examined by electron diffraction at room temperature, revealing the presence of a c-glide plane. Their crystal structure was refined by single crystal x-ray diffraction suggesting an isomorphous solid solution best described with the non-centrosymmetric space group I4cm in the paramagnetic domain. The magnetic measurements confirm the ferromagnetic ordering of the solid solution U{sub 3}Al{sub 2−x}Ge{sub 3+x} with an increase of Tc with the Al content. The thermal variation of the specific heat bear out the magnetic transitions with some delocalized character of the uranium 5f electrons. - Graphical abstract: The phase relations within the U-Al-Ge ternary system were experimentally assessed for two isothermal sections, at 673 K for the whole Gibbs triangle and at 1173 K for the concentration range 25–100 at% U. A complete UAl{sub 3}-UGe{sub 3} solid-solution based on the Cu{sub 3}Au-type forms below the solidus. A unique ternary phase showing a large homogeneity domain, U{sub 3}Al{sub 2−x}Ge{sub 3+x} for −0.1≤x≤1.35 and −0.2≤x≤1.5 at 673 K and 1173 K respectively has been evidenced. It is best described with the non-centrosymmetric space group I4cm above room temperature. A linear increase of the ferromagnetic ordering is observed with the Al content. - Highlights: • Isothermal sections of the U-Al-Ge system were investigated for 673 K and 1173 K. • An isomorphous solid-solution UAl{sub 3}-UGe{sub 3} forms for the whole composition range. • U{sub 3}Al{sub 2−x}Ge{sub 3+x} the unique ternary phase to form exists for a large homogeneity domain. • U{sub 3}Al{sub 2−x}Ge{sub 3+x} is best described in I4cm space group above room temperature. • The ferromagnetic transition of U{sub 3}Al{sub 2−x}Ge{sub 3+x} linearly increases with the Al content.« less

Substituting energy crops with organic wastes and agro-industrial residues for biogas production.

PubMed

Schievano, Andrea; D'Imporzano, Giuliana; Adani, Fabrizio

2009-06-01

In this study, industrial and agro-industrial by-products and residues (BRs), animal manures (AMs), and various types of organic wastes (OWs) were analyzed to evaluate their suitability as substitutes for energy crops (ECs) in biogas production. A comparison between the costs of the volume of biogas that can be produced from each substrate was presented with respect to the prices of the substrates in the Italian market. Furthermore, four different feeding mixtures were compared with a mixture of EC and swine manure (Mixture A) used in a full-scale plant in Italy. Swine manure is always included as a basic substrate in the feeding mixtures, because many of the Italian biogas plants are connected to farms. When EC were partially substituted with BR (Mixture B), the cost (0.28 euro Nm(-3)) of the volume of biogas of Mixture A dropped to 0.18 euro Nm(-3). Furthermore, when the organic fraction of municipal solid waste (OFMSW) and olive oil sludge (OS) were used as possible solutions (Mixtures C and D), the costs of the volume of biogas were -0.20 and 0.11euroNm(-3), respectively. The negative price signifies that operators earn money for treating the waste. For the fifth mix (Mixture E) of the OFMSW with a high solid substrate, such as glycerin from biodiesel production, the resulting cost of the volume of biogas produced was -0.09 euro Nm(-3). By comparing these figures, it is evident that the biogas plants at farm level are good candidates for treating organic residues of both municipalities and the agro-industrial sector in a cost-effective way, and in providing territorially diffused electric and thermal power. This may represent a potential development for agrarian economy.

Spatially resolved micro-Raman observation on the phase separation of effloresced sea salt droplets.

PubMed

Xiao, Han-Shuang; Dong, Jin-Ling; Wang, Liang-Yu; Zhao, Li-Jun; Wang, Feng; Zhang, Yun-Hong

2008-12-01

We report on the investigation of the phase separation of individual seawater droplets in the efflorescence processes with the spatially resolved Raman system. Upon decreasing the relative humidity (RH), CaSO4.0.5H2O separated out foremost fromthe droplet atan unexpectedly high RH of approcimately 90%. Occasionally, CaSO4.2H2O substituted for CaSO4.O.5H2O crystallizing first at approximately 78% RH. Relatively large NaCI solids followed to crystallize at approximately 55% RH and led to the great loss of the solution. Then, the KMgCl3.6H2O crystallites separated out from the residual solutions, adjacentto NaCl at approximately 44% RH. Moreover, a shell structure of dried sea salt particle was found to form at low RHs, with the NaCl crystals in the core and minor supersaturated solutions covered with MgSO4 gel coating on the surface. Ultimately, the shielded solution partly effloresced into MgSO4 hydrates at very dry state (<5% RH).

Compositional limits and analogs of monoclinic triple-chain silicates

NASA Astrophysics Data System (ADS)

Jenkins, David M.; Gilleaudeau, Geoffrey J.; Kawa, Cynthia; Dibiase, Jaclyn M.; Fokin, Maria

2012-08-01

Growing recognition of triple-chain silicates in nature has prompted experimental research into the conditions under which they can form and the extent of solid solution that is feasible for some key chemical substitutions. Experiments were done primarily in the range of 0.1-0.5 GPa and 200-850 °C for durations of 18-1,034 h. A wide range of bulk compositions were explored in this study that can be classified broadly into two groups: those that are Na free and involve various possible chemical substitutions into jimthompsonite (Mg10Si12O32(OH)4), and those that are Na bearing and involve chemical substitutions into the ideal end-member Na4Mg8Si12O32(OH)4. Numerous attempts to synthesize jimthompsonite or clinojimthompsonite were unsuccessful despite the type of starting material used (reagent oxides, magnesite + SiO2, talc + enstatite, or anthophyllite). Similarly, the chemical substitutions of F- for OH-, Mn2+, Ca2+, or Fe2+ for Mg2+, and 2Li+ for Mg2+ and a vacancy were unsuccessful at nucleating triple-chain silicates. Conversely, nearly pure yields of monoclinic triple-chain silicate could be made at temperatures of 440-630 °C and 0.2 GPa from the composition Na4Mg8Si12O32(OH)4, as found in previous studies, though its composition is most likely depleted in Na as evidenced by electron microprobe and FTIR analysis. Pure yields of triple-chain silicate were also obtained for the F-analog composition Na4Mg8Si12O32F4 at 550-750 °C and 0.2-0.5 GPa if a flux consisting of Na-halide salt and water in a 2:1 ratio by weight was used. In addition, limited chemical substitution could be documented for the substitutions of 2 Na+ for Na+ + H+ and of Mg2+ + vacancy for 2Na+. For the former, the Na content appears to be limited to 2.5 cations giving the ideal composition of Na2.5Mg8Si12O30.5(OH)5.5, while for the latter substitution the Na content may go as low as 1.1 cations giving the composition Na1.1Mg9.4Si12O31.9(OH)4.1 based on a fixed number of Si cations. Further investigation involving Mg for Na cation exchange may provide a pathway for the synthesis of Na-free clinojimthompsonite. Fairly extensive solid solution was also observed for triple-chain silicates made along the compositional join Na4Mg8Si12O32(OH)4-Ca2Mg8Si12O32(OH)4 where the limit of Ca substitution at 450 °C and 0.2 GPa corresponds to Na0.7Ca1.8Mg7.8Si12O31.9(OH)4.1 (with the OH content adjusted to achieve charge balance). Aside from the Na content, this composition is similar to that observed as wide-chain lamellae in host actinolite. The relative ease with which Na-rich triple chains can be made experimentally suggests that these phases might exist in nature; this study provides additional insights into the range of compositions and formation conditions at which they might occur.

First-principles study on stability of transition metal solutes in aluminum by analyzing the underlying forces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Wei; Xu, Yichun; Li, Xiangyan

2015-05-07

Although there have been some investigations on behaviors of solutes in metals under strain, the underlying mechanism of how strain changes the stability of a solute is still unknown. To gain such knowledge, first-principles calculations are performed on substitution energy of transition metal solutes in fcc Al host under rhombohedral strain (RS). Our results show that under RS, substitution energy decreases linearly with the increase of outermost d radius r{sub d} of the solute due to Pauli repulsion. The screened Coulomb interaction increases or decreases the substitution energy of a solute on condition that its Pauling electronegativity scale ϕ{sub P}more » is less or greater than that of Al under RS. This paper verifies a linear relation of substitution energy change versus r{sub d} and ϕ{sub P} under RS, which might be instructive for composition design of long life alloys serving in high stress condition.« less

Investigating the Vanadium Environments in Hydroxylamido V(V) Dipicolinate Complexes Using 51V NMR Spectroscopy and Density Functional Theory

PubMed Central

Ooms, Kristopher J.; Bolte, Stephanie E.; Smee, Jason J.; Baruah, Bharat; Crans, Debbie C.; Polenova, Tatyana

2014-01-01

Using 51V magic angle spinning solid-state NMR, SSNMR, spectroscopy and quantum chemical DFT calculations we have characterized the chemical shift and quadrupolar coupling parameters of a series of 8 hydroxylamido vanadium(V) dipicolinate complexes of the general formula VO(dipic)(ONR1R2)(H2O) where R1 and R2 can be H, CH3, or CH2CH3. This class of vanadium compounds was chosen for investigation because of their seven coordinate vanadium atom, a geometry for which there is limited 51V SSNMR data. Furthermore, a systematic series of compounds with different electronic properties are available and allows for the effects of ligand substitution on the NMR parameters to be studied. The quadrupolar coupling constants, CQ, are small, 3.0 to 3.9 MHz, but exhibit variations as a function of the ligand substitution. The chemical shift tensors in the solid state are sensitive to changes in both the hydroxylamide substituent and the dipic ligand, a sensitivity which is not observed for isotropic chemical shifts in solution. The chemical shift tensors span approximately 1000 ppm, and are nearly axially symmetric. Based on DFT calculations of the chemical shift tensors, one of the largest contributors to the magnetic shielding anisotropy is an occupied molecular orbital with significant vanadium dz2 character along the V=O bond. PMID:17902653

Use of frit-disc crucibles for routine and exploratory solution growth of single crystalline samples

DOE PAGES

Canfield, Paul C.; Kong, Tai; Kaluarachchi, Udhara S.; ...

2016-01-05

Solution growth of single crystals from high temperature solutions often involves the separation of residual solution from the grown crystals. For many growths of intermetallic compounds, this separation has historically been achieved with the use of plugs of silica wool. Whereas this is generally efficient in a mechanical sense, it leads to a significant contamination of the decanted liquid with silica fibres. In this paper, we present a simple design for frit-disc alumina crucible sets that has made their use in the growth single crystals from high temperature solutions both simple and affordable. An alumina frit-disc allows for the cleanmore » separation of the residual liquid from the solid phase. This allows for the reuse of the decanted liquid, either for further growth of the same phase, or for subsequent growth of other, related phases. In this article, we provide examples of the growth of isotopically substituted TbCd 6 and icosahedral i-RCd quasicrystals, as well as the separation of (i) the closely related Bi 2Rh 3S 2 and Bi 2Rh 3.5S 2 phases and (ii) and PrZn 11 and PrZn 17.« less

Significantly enhanced ferroelectricity and magnetic properties in (Sr{sub 0.5}Ca{sub 0.5})TiO{sub 3}-modified BiFeO{sub 3} ceramics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Juan; Liu, Xiao Qiang, E-mail: xqliu@zju.edu.cn, E-mail: xmchen59@zju.edu.cn; Chen, Xiang Ming, E-mail: xqliu@zju.edu.cn, E-mail: xmchen59@zju.edu.cn

2015-05-07

BiFeO{sub 3} multiferroic ceramics were modified by introducing (Sr{sub 0.5}Ca{sub 0.5})TiO{sub 3} to form solid solutions. The single phase structure was easy to be obtained in Bi{sub 1−x}(Sr{sub 0.5}Ca{sub 0.5}){sub x}Fe{sub 1−x}Ti{sub x}O{sub 3} (x = 0.2, 0.25, 0.3, and 0.4) solid solutions. Rietveld refinement of X-ray diffraction data revealed a transition from rhombohedral R3c (x = 0.2, 0.25, and 0.3) to orthorhombic Pnma (x = 0.4). Current density-field (J-E) characteristics indicated that the leakage current density was reduced by three orders of magnitude in Bi{sub 1−x}(Sr{sub 0.5}Ca{sub 0.5}){sub x}Fe{sub 1−x}Ti{sub x}O{sub 3} ceramics. Both the ferroelectricity and magnetic properties were significantly enhanced in the presentmore » solid solutions. P-E hysteresis loop measurements with dynamic leakage current compensation methods showed the significantly enhanced ferroelectric properties for x = 0.25 and 0.3 and the paraelectric behavior for x = 0.4. The best ferromagnetic characteristics were achieved in the composition of x = 0.25, where the saturated M-H loop was determined with M{sub r} = 34.8 emu/mol. The improvement of ferroelectricity was mainly due to the suppressed leakage current, and the enhanced magnetism originated from the partial substitution of Fe{sup 3+} by Ti{sup 4+}, which destroyed its previous spiral structure to allow the appearance of a macroscopic magnetization.« less

The interfacial, emulsification and encapsulation properties of hydrophobically modified inulin.

PubMed

Kokubun, S; Ratcliffe, I; Williams, P A

2018-08-15

Octenyl- and dodecenyl succinic anhydride derivatives (OSA- and DDSA-) of inulin have been synthesised and their solution and interfacial properties have been determined and compared to a commercially available alkylated inulin, Inutec SP1. All samples formed micellar aggregates in solution above a critical concentration (critical aggregation concentration) and were able to 'dissolve' a hydrophobic dye. They were also able to form stable oil-in-water (O/W) emulsions as assessed by measurements of their droplet size as a function of time. DDSA-inulin with a high degree of substitution was found to be effective at encapsulating beta carotene using the solvent evaporation method which yielded a solid which dissolved readily in simulated gastric fluid. The results confirm the potential application of these materials in a number of areas including, drug delivery, pharmaceuticals, neutraceuticals, cosmetics and personal care. Copyright © 2018 Elsevier Ltd. All rights reserved.

Degradation of high energetic and insensitive munitions compounds by Fe/Cu bimetal reduction.

PubMed

Koutsospyros, Agamemnon; Pavlov, Julius; Fawcett, Jacqueline; Strickland, David; Smolinski, Benjamin; Braida, Washington

2012-06-15

A reductive technology based on a completely mixed two-phase reactor (bimetallic particles and aqueous stream) was developed for the treatment of aqueous effluents contaminated with nitramines and nitro-substituted energetic materials. Experimental degradation studies were performed using solutions of three high energetics (RDX, HMX, TNT) and three insensitive-munitions components (NTO, NQ, DNAN). The study shows that, on laboratory scale, these energetic compounds are easily degraded in solution by suspensions of bimetallic particles (Fe/Ni and Fe/Cu) prepared by electro-less deposition. The type of bimetal pair (Fe/Cu or Fe/Ni) does not appear to affect the degradation kinetics of RDX, HMX, and TNT. The degradation of all components followed apparent first-order kinetics. The half-lives of all compounds except NTO were under 10 min. Additional parameters affecting the degradation processes were solids loading and initial pH. Copyright © 2012 Elsevier B.V. All rights reserved.

Solubility limits of dibutyl phosphoric acid in uranium-nitric acid solutions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pierce, R.A.

2000-01-04

The Savannah River Site has enriched uranium (EU) solution that has been stored since being purified in its solvent extraction processes. The concentrations in solution are approximately 6 g/L U and 0.1 M nitric acid. Residual tributylphosphate in solution has slowly hydrolyzed to form dibutyl phosphoric acid (HDBP) at concentrations averaging 30--50 mg/L. Dibutyl phosphoric acid, in turn, is in equilibrium with (HDBP){sub 2} and DBP{sup {minus}}. Uranium can form compounds with the dibutylphosphate ion (DBP{sup {minus}}) which have limited solubility, thereby creating a nuclear criticality safety issue. Literature reports and earlier SRTC tests have shown that it is feasiblemore » to precipitate U-DBP solid during the storage and processing of EU solutions. As a result, a series of solubility experiments were run at nitric acid concentrations from 0--4.0 M HNO{sub 3}, uranium at 0--90 g/L, and temperatures from 0--30 C. The data shows temperature and nitric acid concentration dependence consistent with what would be expected. With respect to uranium concentration, U-DBP solubility passes through a minimum between 6 and 12 g/L U at the acid concentrations and temperatures studied. However, the minimum shows a slight shift toward lower uranium concentrations at lower nitric acid concentrations. The shifts in solubility are strongly dependent upon the overall ionic strength of the solution. The data also reveal a shift to higher DBP solubility above 0.5 M HNO{sub 3} for both 6 g/L and 12 g/L uranium solutions. Analysis of U-DBP solids from the tests identified distinct differences between precipitates from less than 0.5 M solutions and those from greater than 4 M acid. Analyses identified UO{sub 2}(DBP){sub 2} as the dominant compound present at low acid concentrations in accordance with literature reports. As the acid concentration increases, the crystalline UO{sub 2}(DBP){sub 2} shows molecular substitutions and an increase in amorphous content.« less

Hydrogen isotopic substitution of solid methylamine through atomic surface reactions at low temperatures: A potential contribution to the D/H ratio of methylamine in molecular clouds

NASA Astrophysics Data System (ADS)

Oba, Yasuhiro; Chigai, Takeshi; Osamura, Yoshihiro; Watanabe, Naoki; Kouchi, Akira

2014-01-01

We experimentally studied hydrogen (H)-deuterium (D) substitution reactions of solid methylamine (CH3NH2) under astrophysically relevant conditions. We also calculated the potential energy surface for the H-D substitution reactions of methylamine isotopologues using quantum chemical methods. Despite the relatively large energy barrier of more than 18 kJ mol-1, CH3NH2 reacted with D atoms to yield deuterated methylamines at 10 K, suggesting that the H-D substitution reaction proceeds through quantum tunneling. Deuterated methylamines reacted with H atoms as well. On the basis of present results, we propose that methylamine has potential for D enrichment through atomic surface reactions on interstellar grains at very low temperatures in molecular clouds. D enrichment would occur in particular in the methyl group of methylamine.

Core Perylene Diimide Designs via Direct Bay- and ortho-(Poly)trifluoromethylation: Synthesis, Isolation, X-Ray Structures, Optical and Electronic Properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clikeman, Tyler T.; Bukovsky, Eric V.; Wang, Xue-Bin

2015-09-22

We developed an efficient solvent- and catalyst-free direct polytrifluoromethylation of solid perylene-3,4,9,10-tetracarboxylic dianhydride that produced a new family of (poly)perfluoroalkyl bay- and ortho-substituted PDIs with two different imide substituents. Direct hydrogen substitution with CN group led to the synthesis of a cyanated perfluoroalkyl PDI derivative for the first time. Absorption, steady-state and time-resolved emission, X-ray diffraction, electrochemical, and gas-phase electron affinity data allowed for systematic studies of substitution effects at bay, ortho, and imide positions in the new PDIs. Solid-state packing showed remarkable variations in the intermolecular interactions that are important for charge transport and photophysical properties. Moreover, analysis ofmore » the electrochemical data for 143 electron poor PDIs, including newly reported compounds, revealed some general trends and peculiar effects from substituting electron-withdrawing groups at all three positions.« less

Core Perylene Diimide Designs via Direct Bay and Ortho (Poly)trifluoromethylation: Synthesis, Isolation, X-ray Structures, Optical and Electronic Properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clikeman, Tyler T.; Bukovsky, Eric V.; Wang, Xue B.

2015-09-22

We developed an efficient solvent- and catalyst-free direct polytrifluoromethylation of solid perylene-3,4,9,10-tetracarboxylic dianhydride that produced a new family of (poly)perfluoroalkyl bay and ortho substituted PDIs with two different imide substituents. Direct hydrogen substitution with CN group led to the synthesis of a cyanated perfluoroalkyl PDI derivative for the first time. Absorption, steady-state and time-resolved emission, X-ray diffraction, electrochemical, and gas-phase electron affinity data allowed for systematic studies of substitution effects at bay, ortho, and imide positions in the new PDIs. Solid-state packing showed remarkable variations in the intermolecular interactions that are important for charge transport and photophysical properties. Analysis ofmore » the electrochemical data for 143 electron poor PDIs, including newly reported compounds, revealed some general trends and peculiar effects of electron withdrawing group substitution at all three positions.« less

Synthesis of Al₂Ca Dispersoids by Powder Metallurgy Using a Mg-Al Alloy and CaO Particles.

PubMed

Fujita, Junji; Umeda, Junko; Kondoh, Katsuyoshi

2017-06-28

The elemental mixture of Mg-6 wt %Al-1 wt %Zn-0.3 wt %Mn (AZ61B) alloy powder and CaO particles was consolidated by an equal-channel angular bulk mechanical alloying (ECABMA) process to form a composite precursor. Subsequently, the precursor was subjected to a heat treatment to synthesize fine Al₂Ca particles via a solid-state reaction between the Mg-Al matrix and CaO additives. Scanning electron microscopy-energy-dispersive spectroscopy (SEM-EDS) and electron probe micro-analysis on the precursor indicated that 4.7-at % Al atoms formed a supersaturated solid solution in the α-Mg matrix. Transmission electron microscopy-EDS and X-ray diffraction analyses on the AZ61B composite precursor with 10-vol % CaO particles obtained by heat treatment confirmed that CaO additives were thermally decomposed in the Mg-Al alloy, and the solid-soluted Ca atoms diffused along the α-Mg grain boundaries. Al atoms also diffused to the grain boundaries because of attraction to the Ca atoms resulting from a strong reactivity between Al and Ca. As a result, needle-like (Mg,Al)₂Ca intermetallics were formed as intermediate precipitates in the initial reaction stage during the heat treatment. Finally, the precipitates were transformed into spherical Al₂Ca particles by the substitution of Al atoms for Mg atoms in (Mg,Al)₂Ca after a long heat treatment.

[Synthesis, characterization and fluorescent properties of copper phthalocyanine derivates substituted by aliphatic alcohol].

PubMed

Zhang, Liang; Xu, Qing-Feng; Lu, Jian-Mei; Yao, She-Chun

2007-04-01

A series of copper phthalocyanine derivatives substituted by aliphatic chain were obtained by the reaction of tetra-formyl chloride copper phthalocyanine and aliphatic alcohol such as n-butyl alcohol, n-amyl alcohol, n-hexyl alcohol, n-caprylic alcohol and lauryl alcohol. IR, UV-Vis, elemental analysis and 1H NMR verified the structures and substituting degree. The solubility and the relationship between fluorescence and concentration and substituting group were studied in organic solution. It was confirmed that the solubility in organic solution was improved greatly, the fluorescence did not change in linear according to the concentration and the fluorescence of copper phthalocyanine derivatives substituted by the long alkyl was stronger than that substituted by the relatively short alkyl.

Kinetics of Hydrogen Diffusion in LaNi(sub 5-x)Sn(sub x) Alloys

NASA Technical Reports Server (NTRS)

Ratnakumar, B. V.; Hightower, A.; Witham, C.; Bowman, R. C.; Fultz, B.

1996-01-01

Solid-state diffusion of hydrogen in metal hydride (MH) alloys is recognized as the rate determining step in the discharge of MH alloys in alkaline Ni-MH rechargeable cells. In our pursuit of new ternary solutes in LaNi(sub 5) for extended cycle lifetimes, we have observed noticeable improvement in the cycle life with small substitutions of Sn and Ge for Ni. Furthermore, these substituents also facilitate enhanced charge transfer kinetics for hydriding-dehydriding process. In this paper, we report our studies on the kinetics of hydrogen diffusion in LaNi(sub 5-x) Sn(sub x) alloys by electrochemical pulse techniques, chronoamperometry and chronocoulometry.

Low temperature co-pyrolysis of hexabenzylditinsulfide and selenium. An alternate route to Sn(S{sub x}Se{sub 1{minus}x})

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boudjouk, P.; Remington, M.P. Jr.; Seidler, D.J.

1999-12-01

Benzyl-substituted tin chalcogenides (Bn{sub 3}Sn){sub 2}S (1) and (Bn{sub 3}Sn){sub 2}Se (2) yield polycrystalline-phase pure SnS and SnSe in good ceramic yields when pyrolyzed with S and Se, respectively, at 275 C. Heating mixtures of (1) and elemental selenium produce solid solutions of the formula Sn(S{sub x}Se{sub 1{minus}x}). Combustion analysis showed less than 1% residual carbon in all ceramic products. This methodology allows the complete conversion of tin-to-tin chalcogenides and eliminates the need to synthesize organosulfur and organoselenium intermediates.

Petro-elastic modelling and characterization of solid-filled reservoirs: Comparative analysis on a Triassic North Sea reservoir

NASA Astrophysics Data System (ADS)

Auduson, Aaron E.

2018-07-01

One of the most common problems in the North Sea is the occurrence of salt (solid) in the pores of Triassic sandstones. Many wells have failed due to interpretation errors based conventional substitution as described by the Gassmann equation. A way forward is to device a means to model and characterize the salt-plugging scenarios. Modelling the effects of fluid and solids on rock velocity and density will ascertain the influence of pore material types on seismic data. In this study, two different rock physics modelling approaches are adopted in solid-fluid substitution, namely the extended Gassmann theory and multi-mineral mixing modelling. Using the modified new Gassmann equation, solid-and-fluid substitutions were performed from gas or water filling in the hydrocarbon reservoirs to salt materials being the pore-filling. Inverse substitutions were also performed from salt-filled case to gas- and water-filled scenarios. The modelling results show very consistent results - Salt-plugged wells clearly showing different elastic parameters when compared with gas- and water-bearing wells. While the Gassmann equation-based modelling was used to discretely compute effective bulk and shear moduli of the salt plugs, the algorithm based on the mineral-mixing (Hashin-Shtrikman) can only predict elastic moduli in a narrow range. Thus, inasmuch as both of these methods can be used to model elastic parameters and characterize pore-fill scenarios, the New Gassmann-based algorithm, which is capable of precisely predicting the elastic parameters, is recommended for use in forward seismic modelling and characterization of this reservoir and other reservoir types. This will significantly help in reducing seismic interpretation errors.

Fermi surfaces and electronic topological transitions in metallic solid solutions

NASA Astrophysics Data System (ADS)

Bruno, E.; Ginatempo, B.; Guiliano, E. S.; Ruban, A. V.; Vekilov, Yu. Kh.

1994-12-01

Notwithstanding the substitutional disorder, the Fermi surface of metallic alloys can be measured and computed. We show that, from the theoretical point of view, it is defined as the locus of the peaks of the Bloch Spectral Function (BSF). Such Fermi surfaces, on varying the atomic concentrations, may undergo changes of their topology, known as Electronic Topological Transitions (ETT). Thus, for instance, pockets of electrons or holes may appear or disappear, necks may open or close. ETTs cause anomalous behaviours of thermodynamic, transport and elastic properties of metals and constitute a fascinating field in the study of Fermi liquid systems. Although ETTs could be studied on pure systems as a function of the thermodynamic variables, nevertheless such a study would often require extreme conditions, and would lead to experimental difficulties. On the other hand, it is possible to explore the variations of atomic concentration, i.e. the valence electron per atom ratio, in metallic solid solutions with a relative experimental ease. In this paper we review the theoretical techniques for the determination of Fermi surfaces in metallic solid solutions and discuss some examples of ETTs, namely LiMg, ZrNb, NbMo, MoRe, AgPd, CdMg, NiW and NiTi alloys, also in connection with experimental data as thermoelectric power, resistivity, elastic constants and electron-phonon coupling and with the determinations of the electron momentum distribution function from Compton scattering and positron annihilation experiments. We show that the ab initio calculations of the electronic structure for the quoted systems, together with a careful determination of the BSF, are able to predict quantitatively ETTs at those concentrations where physical quantities display anomalies, so confirming directly ETT theory. Although it is not the purpose of the present review to give a full account of electronic structure calculation schemes, however, we briefly discuss the ideas and the main physical approximations underlying theories of substitutional disorder in alloys. We shall pay some more attention to the Coherent Potential Approximation (CPA) in the Korringa-Kohn-Rostoker (KKR) multiple scattering framework and the Hohenberg and Kohn Density Functional Theory in the Local Density Approximation (LDA) for the exchange-correlation potential. The above choice is supported by the numerical versatility of the LDAKKRCPA theory, and, more important, by the a fortiori evidence that essentially equivalent results are obtained from different theoretical frameworks, provided the same basic physical approximations are used. Accordingly, when convenient, we present new LDAKKRCPA determinations of the Fermi surfaces, as for the ZrNbMoRe series.

Synthesis and stability of hetaerolite, ZnMn2O4, at 25°C

USGS Publications Warehouse

Hem, J.D.; Roberson, C.E.; Lind, C.J.

1987-01-01

A precipitate of nearly pure hetaerolite, ZnMn2O4, a spinel-structured analog of hausmannite, Mn3O4, was prepared by an irreversible wprecipitation of zinc with manganese at 25°C. The synthesis technique entailed constant slow addition of a dilute solution of Mn2+ and Zn2+ chlorides having a Mn/Zn ratio of 2:1 to a reaction vessel that initially contained distilled deionized water, maintained at a pH of 8.50 by addition of dilute NaOH by an automated pH stat, with continuous bubbling of CO2-free air. The solid was identified by means of X-ray diffraction and transmission electron microscopy and consisted of bipyramidal crystals generally less than 0.10 μm in diameter. Zn2+ ions are able to substitute extensively for Mn2+ ions that occupy tetrahedral sites in the hausmannite structure.Hetaerolite appears to be more stable than hausmannite with respect to spontaneous conversion to γMnOOH. The value of the standard free energy of formation of hetaerolite was estimated from the experimental data to be −289.4 ± 0.8 kcal per mole. Solids intermediate in composition between hetaerolite and hausmannite can be prepared by altering the Mn/Zn ratio in the feed solution.

First-principles thermodynamics study of phase stability in inorganic halide perovskite solid solutions

NASA Astrophysics Data System (ADS)

Bechtel, Jonathon S.; Van der Ven, Anton

2018-04-01

Halide substitution gives rise to a tunable band gap as a function of composition in halide perovskite materials. However, photoinduced phase segregation, observed at room temperature in mixed halide A Pb (IxBr1-x) 3 systems, limits open circuit voltages and decreases photovoltaic device efficiencies. We investigate equilibrium phase stability of orthorhombic P n m a γ -phase CsM (XxY1-x) 3 perovskites where M is Pb or Sn, and X and Y are Br, Cl, or I. Finite-temperature phase diagrams are constructed using a cluster expansion effective Hamiltonian parameterized from first-principles density-functional-theory calculations. Solid solution phases for CsM (IxBr1-x) 3 and CsM (BrxCl1-x) 3 are predicted to be stable well below room temperature while CsM (IxCl1-x) 3 systems have miscibility gaps that extend above 400 K. The height of the miscibility gap correlates with the difference in volume between end members. Also layered ground states are found on the convex hull at x =2 /3 for CsSnBr2Cl ,CsPbI2Br , and CsPbBrCl2. The impact of these ground states on the finite temperature phase diagram is discussed in the context of the experimentally observed photoinduced phase segregation.

Perspectives and limits for cement kilns as a destination for RDF.

PubMed

Genon, G; Brizio, E

2008-11-01

RDF, the high calorific value fraction of MSW obtained by conventional separation systems, can be employed in technological plants (mainly cement kilns) in order to obtain a useful energy recovery. It is interesting and important to evaluate this possibility within the general framework of waste-to-energy solutions. The solution must be assessed on the basis of different aspects, namely: technological features and clinker characteristics; local atmospheric pollution; the effects of RDF used in cement kilns on the generation of greenhouse gases; the economics of conventional solid fuels substitution and planning perspectives, from the point of view of the destination of RDF and optimal cement kiln policy. The different experiences of this issue throughout Europe are reviewed, and some applications within Italy are also been considered. The main findings of the study are that the use of RDF in cement kilns instead of coal or coke offers environmental benefits in terms of greenhouse gases, while the formation of conventional gaseous pollutants is not a critical aspect. Indeed, the generation of nitrogen oxides can probably be lower because of lower flame temperatures or lower air excess. The presence of chlorinated micro-pollutants is not influenced by the presence of RDF in fuel, whereas depending on the quality of the RDF, some problems could arise compared to the substituted fuel as far as heavy metals are concerned, chiefly the more volatile ones.

Perspectives and limits for cement kilns as a destination for RDF

DOE Office of Scientific and Technical Information (OSTI.GOV)

Genon, G.; Brizio, E.

2008-11-15

RDF, the high calorific value fraction of MSW obtained by conventional separation systems, can be employed in technological plants (mainly cement kilns) in order to obtain a useful energy recovery. It is interesting and important to evaluate this possibility within the general framework of waste-to-energy solutions. The solution must be assessed on the basis of different aspects, namely: technological features and clinker characteristics; local atmospheric pollution; the effects of RDF used in cement kilns on the generation of greenhouse gases; the economics of conventional solid fuels substitution and planning perspectives, from the point of view of the destination of RDFmore » and optimal cement kiln policy. The different experiences of this issue throughout Europe are reviewed, and some applications within Italy are also been considered. The main findings of the study are that the use of RDF in cement kilns instead of coal or coke offers environmental benefits in terms of greenhouse gases, while the formation of conventional gaseous pollutants is not a critical aspect. Indeed, the generation of nitrogen oxides can probably be lower because of lower flame temperatures or lower air excess. The presence of chlorinated micro-pollutants is not influenced by the presence of RDF in fuel, whereas depending on the quality of the RDF, some problems could arise compared to the substituted fuel as far as heavy metals are concerned, chiefly the more volatile ones.« less

Experimental thermochemistry of neptunium oxides: Np2O5 and NpO2

NASA Astrophysics Data System (ADS)

Zhang, Lei; Dzik, Ewa A.; Sigmon, Ginger E.; Szymanowski, Jennifer E. S.; Navrotsky, Alexandra; Burns, Peter C.

2018-04-01

Neptunium (Np) compounds are important in the nuclear fuel cycle because of the buildup and long half-life (2.14 Ma) of Np-237 in nuclear waste, especially during long-term disposal in a geological repository. Neptunium in environmental conditions exists mainly in two oxidation states (+5 and + 4) and can substitute for uranium and/or rare earths in solid phases. Yet thermochemical data for solid neptunium compounds are scarce, despite being critical for evaluating the environmental transport of this radioactive and toxic element. Although high temperature oxide melt solution calorimetry has proven very useful in obtaining thermodynamic data for the formation of uranium and thorium oxide materials, it has not yet been applied to transuranium compounds. Continuing a program at Notre Dame to study the thermodynamics of transuranium compounds, we report the first determination of the enthalpies of drop solution of well-characterized neptunium oxides (Np2O5 and NpO2) using oxide melt solution calorimetry in molten sodium molybdate solvent at 973 K. The enthalpy of the decomposition reaction, Np2O5(cr) = 2NpO2(cr) + 1/2O2(g) at 298 K, is determined to be 7.70 ± 5.86 kJ/mol, and this direct measurement is consistent with existing thermodynamic data. The calorimetric methodology is straightforward and produces reliable data using milligram quantities of radioactive materials, and can be applied to many other transuranium compounds.

Reduction and Simultaneous Removal of 99 Tc and Cr by Fe(OH) 2 (s) Mineral Transformation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saslow, Sarah A.; Um, Wooyong; Pearce, Carolyn I.

Technetium (Tc) remains a priority remediation concern due to persistent challenges, including rapid re-oxidation of immobilized Tc, and competing contaminants, e.g. Cr(VI), that inhibit targeted Tc reduction and incorporation into stable mineral phases. Here Fe(OH) 2(s) is investigated as a comprehensive solution for overcoming these challenges, by serving as both the reductant, (Fe(II)), and immobilization agent to form Tc-incorporated magnetite (Fe 3O 4). Trace metal analysis suggests removal of Tc(VII) and Cr(VI) from solution occurs simultaneously; however, complete removal and reduction of Cr(VI) is achieved earlier than the removal/reduction of co-mingled Tc(VII). Bulk oxidation state analysis of the magnetite solidmore » phase by XANES confirms that the majority of Tc is Tc(IV), which is corroborated by XPS. Furthermore, EXAFS results show successful Tc(IV) incorporation into magnetite octahedral sites without additional substitution of Cr or Tc into neighboring Fe octahedral sites. XPS analysis of Cr confirms reduction to Cr(III) and the formation of a Cr-incorporated spinel, Cr2O 3, and Cr(OH)3 phases. Spinel (modeled as Fe 3O 4), goethite, and feroxyhyte are detected in all reacted solid phase samples analyzed by XRD, where Tc(IV) incorporation has little effect on the spinel lattice structure. In the presence of Cr(III) a spinel phase along the magnetite-chromite (Fe 3O 4-FeCr 2O 4) solid-solution line is formed.« less

First quadruple-glycine bridging mono-lanthanide-substituted borotungstate hybrids.

PubMed

Liu, Jiancai; Yu, Jing; Han, Qing; Wen, Yue; Chen, Lijuan; Zhao, Junwei

2016-10-18

A class of novel organic-inorganic hybrid lanthanide (Ln)-substituted Keggin-type borotungstates K 4 Na 4 H 4 [Ln 2 (gly) 4 (α-BW 11 O 39 ) 2 ]·23H 2 O [Ln = Ce 3+ (1), Pr 3+ (2), Nd 3+ (3), Sm 3+ (4), Eu 3+ (5), Tm 3+ (6); gly = glycine] have been synthesized from the reaction of K 8 [BW 11 O 39 H]·13H 2 O, NaAc·6H 2 O and Ln(NO 3 ) 3 ·6H 2 O by employing gly ligands as structure-stabilizing agents in the conventional aqueous solution system and structurally characterized by elemental analyses, IR spectroscopy, thermogravimetric (TG) analyses, powder X-ray diffraction (PXRD) and single-crystal X-ray diffraction. The common prominent structural feature of isomorphic 1-6 is that all of them consist of two mono-Ln-substituted Keggin [Ln(α-BW 11 O 39 )] 6- fragments linked by four gly ligands, furnishing an intriguing dimeric assembly of the quadruple-gly-connective mono-Ln-substituted borotungstate, in which each carboxylic oxygen atom from gly ligands is bound to Ln 3+ cations in the μ 2 -O or μ 3 -O mode. To the best of our knowledge, 1-6 represent the first examples of inorganic-organic hybrid Ln-substituted borotungstates functionalized by quadruple amino acid bridges. The solid-state photoluminescence properties of 3-5 have been determined at ambient temperature and the photoluminescence emission spectra exhibit the characteristic emission bands derived from Ln 3+ centers. The thermostability of 1-6 has been studied and the thermal decomposition procedure of 3 has been comprehensively investigated with the assistance of variable-temperature PXRD patterns and variable-temperature IR spectra. Furthermore, magnetic susceptibility measurements of 1, 2 and 4 have been conducted.

End-Member Formulation of Solid Solutions and Reactive Transport

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lichtner, Peter C.

2015-09-01

A model for incorporating solid solutions into reactive transport equations is presented based on an end-member representation. Reactive transport equations are solved directly for the composition and bulk concentration of the solid solution. Reactions of a solid solution with an aqueous solution are formulated in terms of an overall stoichiometric reaction corresponding to a time-varying composition and exchange reactions, equivalent to reaction end-members. Reaction rates are treated kinetically using a transition state rate law for the overall reaction and a pseudo-kinetic rate law for exchange reactions. The composition of the solid solution at the onset of precipitation is assumed tomore » correspond to the least soluble composition, equivalent to the composition at equilibrium. The stoichiometric saturation determines if the solid solution is super-saturated with respect to the aqueous solution. The method is implemented for a simple prototype batch reactor using Mathematica for a binary solid solution. Finally, the sensitivity of the results on the kinetic rate constant for a binary solid solution is investigated for reaction of an initially stoichiometric solid phase with an undersaturated aqueous solution.« less

Oxygen ionic conductivity of NTE materials of cubic Zr 1- xLn xW 2- yMo yO 8- x/2 (Ln = Er, Yb)

NASA Astrophysics Data System (ADS)

Li, Hai-Hua; Xia, Hai-Ting; Jing, Xi-Ping; Zhao, Xin-Hua

2008-08-01

Cubic Zr 1- xLn xW 2- yMo yO 8- x/2 (Ln = Er: x = 0.01, 0.02, 0.03; y = 0; Ln = Yb: x = 0.02, 0.03; y = 0.4) solid solutions, well-known negative thermal expansion (NTE) materials were prepared by using conventional solid state reactions. The morphology and the composition of the fracture surfaces of the ceramic pellets were determined by SEM and EDX technology. The conductance properties of the pellets, such as conductivity and conductance activation energy, were studied by AC impedance spectroscopy and the materials perform clearly oxygen ionic conduction with the conductivity of about 10 -4 S cm -1 at 673 K, a comparable value to that of ceria based solid electrolytes. The substitution of Mo for W enhanced the thermal stability of ZrW 2O 8, so that the conductivity of Zr 0.98Yb 0.02W 1.6Mo 0.4O 7.99 ceramic can be measured up to 873 K, which is about 5.9 × 10 -4 S cm -1.

Effect of Ni on Fe FeS phase relations at high pressure and high temperature

NASA Astrophysics Data System (ADS)

Zhang, Li; Fei, Yingwei

2008-04-01

A series of melting experiments in the Fe-rich portion of the Fe-Ni-S system have been conducted at 19-23 GPa and 800-1100 °C. The solubility of S in the Fe-Ni solid alloy and the eutectic melting in the Fe-Ni-S system were determined as a function of Ni content. The maximum S solubility in the Fe-Ni alloy is 2.7 wt.% at 20 GPa and the eutectic temperature. The eutectic melting temperature in the Fe-Ni(5wt.%)-S system is ~ 1000 °C lower than the melting point of pure Fe at 20 GPa. We also found that Ni can substitute Fe in the Fe 3S structure to form (Fe,Ni) 3S solid solutions up to at least a Fe/Ni atomic ratio of 0.5. Similar to melting behavior in the Fe-FeS system, the eutectic melting relations in the Fe-Ni-S system could produce inner and outer cores with the right light element balance to account for the density difference between the solid inner core and the liquid outer core.

Thermodynamic Properties of Liquid Silver-Antimony-Tin Alloys Determined from Electrochemical and Calorimetric Measurements

NASA Astrophysics Data System (ADS)

Łapsa, Joanna; Onderka, Bogusław

2016-08-01

The thermodynamic properties of liquid Ag-Sb-Sn alloys were obtained through use of the drop solution calorimetric method and electromotive force (emf) measurements of galvanic cells with a yttria stabilized zirconia (YSZ) solid electrolyte. The experiments were carried out along Ag0.25Sb0.75, Ag0.5Sb0.5 and Ag0.75Sb0.25 sections of the ternary system in the temperature range from 973 K to 1223 K. From the measured emf, the tin activity in liquid solutions of Ag-Sb-Sn was determined for the first time. The partial and integral enthalpy of mixing were determined from calorimetric measurements at two temperatures. These measurements were performed along two cross-sections: Sb0.5Sn0.5 at 912 K and 1075 K, and Ag0.75Sb0.25 at 1075 K. Both experimental data sets were used to find ternary interaction parameters by applying the Redlich-Kister-Muggianu model of the substitutional solution. Consequently, the set of parameters describing the thermodynamic properties of the liquid phase was derived.

Green rusts synthesis by coprecipitation of Fe II-Fe III ions and mass-balance diagram

NASA Astrophysics Data System (ADS)

Ruby, Christian; Aïssa, Rabha; Géhin, Antoine; Cortot, Jérôme; Abdelmoula, Mustapha; Génin, Jean-Marie

2006-06-01

A basic solution is progressively added to various mixed Fe II-Fe III solutions. The nature and the relative quantities of the compounds that form can be visualised in a mass-balance diagram. The formation of hydroxysulphate green rust {GR( SO42-)} is preceded by the precipitation of a sulphated ferric basic salt that transforms in a badly ordered ferric oxyhydroxide. Then octahedrally coordinated Fe II species and SO42- anions are adsorbed on the FeOOH surface and GR( SO42-) is formed at the solid/solution interface. By using the same method of preparation, other types of green rust were synthesised, e.g. hydroxycarbonate green rust {GR( CO32-)}. Like other layered double hydroxides, green rusts obey the general chemical formula [ṡ[ṡmHO]x+ with x⩽1/3. Al-substituted hydroxysulphate green rust consists of small hexagonal crystals with a lateral size ˜50 nm, which is significantly smaller than the size of the GR( SO42-) crystals (˜500 nm). To cite this article: C. Ruby et al., C. R. Geoscience 338 (2006).

Raman spectroscopic study of synthetic pyrope-grossular garnets: structural implications

NASA Astrophysics Data System (ADS)

Du, Wei; Han, Baofu; Clark, Simon Martin; Wang, Yichuan; Liu, Xi

2018-02-01

A study of the effect of substitution of Mg and Ca in garnet solid solution (Grtss) was carried out using Raman spectroscopy to probe changes to the crystal lattice. The garnet solid solutions with composition changing along pyrope (Py; Mg3Al2Si3O12) and grossular (Gr; Ca3Al2Si3O12) binary were synthesized from glass at 6 GPa and 1400 °C and a second series of Grtss with composition Py40Gr60 were synthesized at 6 GPa but different temperatures from 1000 to 1400 °C. Raman mode assignments were made based on a comparison with the two end members pyrope and grossular, which show consistent result with literature study on single crystals data. The correlation between the Raman mode frequencies and compositional changes along the pyrope-grossular binary suggests a two-mode behavior for Mg and Ca cations in the garnet structure. The full widths at half-maximum of selected Raman modes increase on moving away from the end members and are about double the end-member values in the mid-position, where the frequencies closely linearly change with composition. The frequencies of the translational modes of the SiO4 tetrahedron (T(SiO4)) show large deviations from linearity indicating a strong kinematic coupling with the translational modes of the Ca and Mg cations. The anomalies in T(SiO4) are linked to mixing unit cell volume, suggesting that the nonlinear mixing volume behavior along the pyrope-grossular binary is related to the resistance of the Si-O bond to expansion and compression, which is caused by substitution of Mg and Ca cations in the dodecahedral sites. Annealing temperature also shows effect on Raman mode frequencies, but the main factor controlling the changes in mode frequencies along pyrope-grossular binary is composition.

Effect of heat moisture treatment (HMT) on product quality of sorghum starch

NASA Astrophysics Data System (ADS)

Haryani, Kristinah; Hadiyanto, Handayani, Noera; Nugraheni, Dwi; Suryanto

2015-12-01

Sorghum is a cereal plant that rich of nutrition contents. The high content of carbohydrate in sorghum make this plant can be processed into one of the processed food i.e vermicelli. To give better quality, it is necessary to use flour substitution from sorghum starch. The aim of this study was to evaluate the treatment of natural sorghum starch substitution, the addition of CMC, and a comparison of the natural starch with starch sorghum forage sorghum against solid losses value, rehydration weight and texture profiles. The variable used in this study: amount of natural sorghum starch subtituion (10%, 20%, 30%, 40%, 50%), the addition of CMC (0.1%; 0.2%; 0.3%; 0.4%; 0.5%) and substituting sorghum starch Natural: HMT sorghum starch (1: 1; 1: 2; 1: 3; 1: 4; 1: 5) and the quality parameters were evaluated. The result indicated that to substitute sorghum starch naturally at a rate of 50% had the best results with a value of solid losses 5.1% (white sorghum) 5.83% (red sorghum) and weighing rehydration 301.82% (white sorghums) 293.16% (red sorghum), the addition of CMC with 0.5% concentration of 3.96% solid losses value (red sorghum) 4:21% (white sorghums) and weight rehydration 252.71% (white sorghums) 244.45% (red sorghums).

The influence of metakaolin substitution by slag in alkali-activated inorganic binders for civil engineering

NASA Astrophysics Data System (ADS)

Kadlec, J.; Rieger, D.; Kovářík, T.; Novotný, P.; Franče, P.; Pola, M.

2017-02-01

In this study the effect of metakaolin replacement by milled blast furnace slag in alkali-activated geopolymeric binder was investigated in accordance to their rheological and mechanical properties. It was demonstrated that slag addition into the metakaolin binder can improve mechanical properties of final products. Our investigation was focused on broad interval of metakaolin substitution in the range from 100 to 40 volume per cents of metakaolin so that the volume content of solids in final binder was maintained constant. Prepared binders were activated by alkaline solution of potassium silicate with silicate module of 1.61. The particle size analyses were performed for determination of particle size distribution. The rheological properties were determined in accordance to flow properties by measurements on Ford viscosity cup and by oscillatory measurements of hardening process. For the investigation of hardening process, the strain controlled small amplitude oscillatory rheometry was used in plane-plate geometry. For determination of applied mechanical properties were binders filled by ceramic grog in the granularity range 0-1 mm. The filling was maintained constant at 275 volume per cents in accordance to ratio of solids in dry binder. The mechanical properties were investigated after 1, 7 and 28 days and microstructure was documented by scanning electron microscopy. The results indicate that slag addition have beneficial effect not only on mechanical properties of hardened binder but also on flow properties of fresh geopolymer paste and subsequent hardening kinetics of alkali-activated binders.

Incorporation of oxidized uranium into Fe (hydr)oxides during Fe(II) catalyzed remineralization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nico, Peter S.; Stewart, Brandy D.; Fendorf, Scott

2009-07-01

The form of solid phase U after Fe(II) induced anaerobic remineralization of ferrihydrite in the presence of aqueous and absorbed U(VI) was investigated under both abiotic batch and biotic flow conditions. Experiments were conducted with synthetic ground waters containing 0.168 mM U(VI), 3.8 mM carbonate, and 3.0 mM Ca{sup 2+}. In spite of the high solubility of U(VI) under these conditions, appreciable removal of U(VI) from solution was observed in both the abiotic and biotic systems. The majority of the removed U was determined to be substituted as oxidized U (U(VI) or U(V)) into the octahedral position of the goethitemore » and magnetite formed during ferrihydrite remineralization. It is estimated that between 3% and 6% of octahedral Fe(III) centers in the new Fe minerals were occupied by U(VI). This site specific substitution is distinct from the non-specific U co-precipitation processes in which uranyl compounds, e.g. uranyl hydroxide or carbonate, are entrapped with newly formed Fe oxides. The prevalence of site specific U incorporation under both abiotic and biotic conditions and the fact that the produced solids were shown to be resistant to both extraction (30 mM KHCO{sub 3}) and oxidation (air for 5 days) suggest the potential importance of sequestration in Fe oxides as a stable and immobile form of U in the environment.« less

β-Lactam antibiotics. Spectroscopy and molecular orbital (MO) calculations . Part I: IR studies of complexation in penicillin-transition metal ion systems and semi-empirical PM3 calculations on simple model compounds

NASA Astrophysics Data System (ADS)

Kupka, Teobald

1997-12-01

IR studies were preformed to determine possible transition metal ion binding sites of penicillin. the observed changes in spectral position and shape of characteristic IR bands of cloxacillin in the presence of transition metal ions (both in solutions and in the solid state) indicate formation of M-L complexes with engagement of -COO - and/or -CONH- functional groups. The small shift of νCO towards higher frequencies rules out direct M-L interaction via β-lactam carbonyl. PM3 calculations on simple model compounds (substituted formamide, cyclic ketones, lactams and substituted monocyclic β-lactams) have been performed. All structures were fully optimized and the calculated bond lengths, angles, heats of formation and CO stretching frequencies were discussed to determine the β-lactam binding sites and to explain its susceptibility towards nucleophilic attack (hydrolysis in vitro) and biological activity. The relative changes of calculated values were critically compared with available experimental data and same correlation between structural parameters and in vivo activity was shown.

Synthetic, Infrared, 1Hand 13CNMR Spectral Studies on N-(p-Substituted Phenyl)-p-Substituted Benzenesulphonamides, p-X'C6H4SO2NH- (p-XC6H4), where X' or X = H, CH3, C2H5, F, Cl or Br

NASA Astrophysics Data System (ADS)

Gowda, B. Thimme; Jayalakshmi, K. L.; Shetty, Mahesha

2004-05-01

Thirty N-(p-substituted phenyl)-p-substituted benzenesulphonamides of the general formula, p-X'C6H4SO2NH(p-XC6H4), where X' or X = H, CH3, C2H5, F, Cl or Br, are synthesised and their infrared spectra in the solid state and 1H and 13C NMR spectra in solution are measured. The N-H stretching vibrational frequencies, νN-H vary in the range 3334 - 3219 cm-1, while the asymmetric and symmetric SO2 vibrations appear in the ranges 1377 - 1311 cm-1 and 1182 - 1151 cm-1, respectively. The compounds exhibit S-N and C-N stretching vibrational absorptions in the ranges 937 - 898 cm-1 and 1310 - 1180 cm-1, respectively. There are no particular trends in the variation of these frequencies on substitution with either electron withdrawing or electron donating groups. The 1H and 13C chemical shifts of N-(p-substituted phenyl)-p-substituted benzenesulphonamides, are assigned to various protons and carbons of the two benzene rings. Further, incremental shifts of the ring protons and carbons due to -SO2NH(p-XC6H4) groups in the compounds of the formula, C6H5SO2NH(p-XC6H4), and p-X'C6H4SO2- and p-X'C6H4SO2NH- groups in the compounds of the formula, p-X'C6H4SO2NH(C6H5) are computed and used to calculate the 1H and 13C chemical shifts of the parallely substituted compounds of the general formula p-X'C6H4SO2NH(p-XC6H4). The computed values agree well with the observed chemical shifts. The above incremental shifts are found to correlate with the Hammett substituent parameters.

Substituent effect on photophysical properties of bi-1,3,4-oxadiazole derivatives in solution

NASA Astrophysics Data System (ADS)

Chen, Fangyi; Tian, Taiji; Zhao, Chengxiao; Bai, Binglian; Li, Min; Wang, Haitao

2016-04-01

A series of phenyl substituted bi-1,3,4-oxadiazole derivatives were designed and synthesized; the effect of substituent on the photophysical properties and molecular electronic structures was fully studied by the combination of experimental techniques and theoretical calculations. Compared to parent compound without any substituent (BOXD), fluoro-substituent shows little effect on the absorption and emission spectra, whilst a little larger spectral red-shift could be observed for methoxy-, nitro-substituted derivatives and thienyl-substituted bi-1,3,4-oxadiazole (TBOXD). These spectral changes can be well explained by theoretically calculated HOMO and LUMO energy level changes. All these molecules show high fluorescence quantum yield except for nitro-substituted derivative in dilute solutions. The quantum yield of BOXD changes with the concentration and exhibits a high value at the concentrated solution. This work revealed the influence of substituent on the photophysical properties of bi-1,3,4-oxadizaole derivatives in dilute solutions and provided guidance for designing molecules with potential application.

Characterization of Non-Innocent Metal Complexes Using Solid-State NMR Spectroscopy: o-Dioxolene Vanadium Complexes

PubMed Central

Chatterjee, Pabitra B.; Goncharov-Zapata, Olga; Quinn, Laurence L.; Hou, Guangjin; Hamaed, Hiyam; Schurko, Robert W.; Polenova, Tatyana; Crans, Debbie C.

2012-01-01

51V solid-state NMR (SSNMR) studies of a series of non-innocent vanadium(V) catechol complexes have been conducted to evaluate the possibility that 51V NMR observables, quadrupolar and chemical shift anisotropies, and electronic structures of such compounds can be used to characterize these compounds. The vanadium(V) catechol complexes described in these studies have relatively small quadrupolar coupling constants, which cover a surprisingly small range from 3.4 to 4.2 MHz. On the other hand, isotropic 51V NMR chemical shifts cover a wide range from −200 ppm to 400 ppm in solution and from −219 to 530 ppm in the solid state. A linear correlation of 51V NMR isotropic solution and solid-state chemical shifts of complexes containing non-innocent ligands is observed. These experimental results provide the information needed for the application of 51V SSNMR spectroscopy in characterizing the electronic properties of a wide variety of vanadium-containing systems, and in particular those containing non-innocent ligands and that have chemical shifts outside the populated range of −300 ppm to −700 ppm. The studies presented in this report demonstrate that the small quadrupolar couplings covering a narrow range of values reflect the symmetric electronic charge distribution, which is also similar across these complexes. These quadrupolar interaction parameters alone are not sufficient to capture the rich electronic structure of these complexes. In contrast, the chemical shift anisotropy tensor elements accessible from 51V SSNMR experiments are a highly sensitive probe of subtle differences in electronic distribution and orbital occupancy in these compounds. Quantum chemical (DFT) calculations of NMR parameters for [VO(hshed)(Cat)] yield 51V CSA tensor in reasonable agreement with the experimental results, but surprisingly, the calculated quadrupolar coupling constant is significantly greater than the experimental value. The studies demonstrate that substitution of the catechol ligand with electron donating groups results in an increase in the HOMO-LUMO gap and can be directly followed by an upfield shift for the vanadium catechol complex. In contrast, substitution of the catechol ligand with electron withdrawing groups results in a decrease in the HOMO-LUMO gap and can directly be followed by a downfield shift for the complex. The vanadium catechol complexes were used in this work because the 51V is a half-integer quadrupolar nucleus whose NMR observables are highly sensitive to the local environment. However, the results are general and could be extended to other redox active complexes that exhibit similar coordination chemistry as the vanadium catechol complexes. PMID:21842875

A high-conduction Ge substituted Li3AsS4 solid electrolyte with exceptional low activation energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sahu, Gayatri; Rangasamy, Ezhiylmurugan; Li, Juchuan

2014-04-16

In lithium-ion conducting solid electrolytes the potential to enable high-energy-density secondary batteries and offer distinctive safety features as an advantage over traditional liquid electrolytes is shown. Achieving the combination of high ionic conductivity, low activation energy, and outstanding electrochemical stability in crystalline solid electrolytes is a challenge for the synthesis of novel solid electrolytes. We report an exceptionally low activation energy (Ea) and high room temperature superionic conductivity via facile aliovalent substitution of Li 3AsS 4 by Ge, which increased the conductivity by two orders of magnitude as compared to the parent compound. The composition Li 3.334Ge 0.334As 0.666S 4more » has a high ionic conductivity of 1.12 mScm -1 at 27°C. Local Li + hopping in this material is accompanied by distinctive low activation energy Ea of 0.17 eV being the lowest of Li + solid conductors. Finally, our study demonstrates the efficacy of surface passivation of solid electrolyte to achieve compatibility with metallic lithium electrodes.« less

Spectroscopic and DFT Study of RhIII Chloro Complex Transformation in Alkaline Solutions.

PubMed

Vasilchenko, Danila B; Berdyugin, Semen N; Korenev, Sergey V; O'Kennedy, Sean; Gerber, Wilhelmus J

2017-09-05

The hydrolysis of [RhCl 6 ] 3- in NaOH-water solutions was studied by spectrophotometric methods. The reaction proceeds via successive substitution of chloride with hydroxide to quantitatively form [Rh(OH) 6 ] 3- . Ligand substitution kinetics was studied in an aqueous 0.434-1.085 M NaOH matrix in the temperature range 5.5-15.3 °C. Transformation of [RhCl 6 ] 3- into [RhCl 5 (OH)] 3- was found to be the rate-determining step with activation parameters of ΔH † = 105 ± 4 kJ mol -1 and ΔS † = 59 ± 10 J K -1 mol -1 . The coordinated hydroxo ligand(s) induces rapid ligand substitution to form [Rh(OH) 6 ] 3- . By simulating ligand substitution as a dissociative mechanism, using density functional theory (DFT), we can now explain the relatively fast and slow kinetics of chloride substitution in basic and acidic matrices, respectively. Moreover, the DFT calculated activation energies corroborated experimental data that the kinetic stereochemical sequence of [RhCl 6 ] 3- hydrolysis in an acidic solution proceeds as [RhCl 6 ] 3- → [RhCl 5 (H 2 O)] 2- → cis-[RhCl 4 (H 2 O) 2 ] - . However, DFT calculations predict in a basic solution the trans route of substitution [RhCl 6 ] 3- → [RhCl 5 (OH)] 3- → trans-[RhCl 4 (OH) 2 ] 3- is kinetically favored.

Supramolecular self-assemblies of beta-cyclodextrins with aromatic tethers: factors governing the helical columnar versus linear channel superstructures.

PubMed

Liu, Yu; Fan, Zhi; Zhang, Heng-Yi; Yang, Ying-Wei; Ding, Fei; Liu, Shuang-Xi; Wu, Xue; Wada, Takehiko; Inoue, Yoshihisa

2003-10-31

A series of 6-O-(p-substituted phenyl)-modified beta-cyclodextrin derivatives, i.e., 6-O-(4-bromophenyl)-beta-CD (1), 6-O-(4-nitrophenyl)-beta-CD (2), 6-O-(4-formylphenyl)-beta-CD (3), 6-phenylselenyl-6-deoxy-beta-CD (4), and 6-O-(4-hydroxybenzoyl)-beta-CD (5), were synthesized, and their inclusion complexation behavior in aqueous solution and self-assembling behavior in the solid state were comparatively studied by NMR spectroscopy, microcalorimetry, crystallography, and scanning tunneling microscopy. Interestingly, (seleno)ethers 1-4 and ester 5 displayed distinctly different self-assembling behavior in the solid state, affording a successively threading head-to-tail polymeric helical structure for the (seleno)ethers or a mutually penetrating tail-to-tail dimeric columnar channel structure for the ester. Combining the present and previous structures reported for the relevant beta-CD derivatives, we further deduce that the pivot heteroatom, through which the aromatic substituent is tethered to beta-CD, plays a critical role in determining the helix structure, endowing the 2-fold and 4-fold axes to the N/O- and S/Se-pivoted beta-CD aggregates, respectively. This means that one can control the self-assembling orientation, alignment, and helicity in the solid state by finely tuning the pivot atom and the tether length. Further NMR and calorimetric studies on the self-assembling behavior in aqueous solution revealed that the dimerization step is the key to the formation of linear polymeric supramolecular architecture, which is driven by favorable entropic contributions.

Solutions as solutions--synthesis and use of a liquid polyester excipient to dissolve lipophilic drugs and formulate sustained-release parenterals.

PubMed

Asmus, Lutz R; Gurny, Robert; Möller, Michael

2011-11-01

Solid poly(lactides) and poly(lactide-co-glycolides) are widely used polymers for sustained-release parenterals. However, they have some unfavorable properties regarding manufacturing of the formulations and administration to the patient due to their solid aggregate state. In contrast, hexyl-substituted poly(lactic acid) (hexPLA, poly(2-hydroxyoctanoic acid)) is a viscous degradable polyester. To date, a two-step ring-opening polymerization was used for its synthesis. Here, we investigated a novel one-pot one-step melt polycondensation method to prepare hexPLA for biomedical applications by a simple green chemistry process. No catalyst or solely pharmaceutically acceptable catalysts and environmentally friendly purification methods without organic solvents were used. The resulting hexPLA polymers are stable under dry heat sterilization conditions. Low molecular weight hexPLAs with less than 5000 g/mol are less viscous than high molecular weight polymers. HexPLA can dissolve lipophilic active substances, with generally high incorporation capacities in low molecular weight polymers. The incorporation of solid compounds increases the viscosity and glass transition temperature, whereas the addition of small amounts of plasticizers or sparse warming significantly decreases the viscosity. Loratadine is soluble in hexPLA up to 28%. This highly concentrated Loratadine-hexPLA formulation released the active compound entirely over 14 days without initial burst in a zero order kinetic, matching the clinical requirements for such a sustained-release formulation. This demonstrates the potential of hexPLA as an excipient for injectable sustained-release formulations. Copyright © 2011 Elsevier B.V. All rights reserved.

Raman and Fourier transform infrared spectroscopic study of pyromorphite-vanadinite solid solutions

NASA Astrophysics Data System (ADS)

Solecka, Urszula; Bajda, Tomasz; Topolska, Justyna; Zelek-Pogudz, Sylwia; Manecki, Maciej

2018-02-01

Due to the great range of the application fields for apatites, there is a strong need to complete the data set determining the properties of these minerals. In this study, Raman and Infrared spectra of the phases from pyromorphite Pb5(PO4)3Cl - vanadinite Pb5(VO4)3Cl series were investigated. Totally, 9 samples (2 end-members and 7 solid solutions of the series) were synthesized at 25 °C and pH = 3.5, and analyzed. In the Raman and Infrared spectra of the studied Pb-apatites, the bands typical for the vibrations in the PO4 and the VO4 tetrahedra appeared. The bands attributed to the stretching vibrations (ν1, ν3) occurred in the 1050-910 cm- 1 and 830-720 cm- 1 regions, whereas the bending vibrations (ν2, ν4) were visible at the 580-540 cm- 1, 430-380 cm- 1 and 370-290 cm- 1 range. The position of the bands depended on the P/(P + V) ratio in the analyzed solid, since there are differences in the ionic radii and the atomic mass of P5 + and V5 +, which affect the bong lengths, bond forces and the banding energies of the substituting tetrahedra. The analysis allowed observing gradual shifts of the bands caused by the replacement of phosphorous with vanadium in the studied phases. The positions and the intensities of selected bands are proposed to serve as a semi-quantitative estimation of the chemical composition of the phases from the pyromorphite - vanadinite series.

Synthesis of Ti3AuC2, Ti3Au2C2 and Ti3IrC2 by noble metal substitution reaction in Ti3SiC2 for high-temperature-stable Ohmic contacts to SiC

NASA Astrophysics Data System (ADS)

Fashandi, Hossein; Dahlqvist, Martin; Lu, Jun; Palisaitis, Justinas; Simak, Sergei I.; Abrikosov, Igor A.; Rosen, Johanna; Hultman, Lars; Andersson, Mike; Lloyd Spetz, Anita; Eklund, Per

2017-08-01

The large class of layered ceramics encompasses both van der Waals (vdW) and non-vdW solids. While intercalation of noble metals in vdW solids is known, formation of compounds by incorporation of noble-metal layers in non-vdW layered solids is largely unexplored. Here, we show formation of Ti3AuC2 and Ti3Au2C2 phases with up to 31% lattice swelling by a substitutional solid-state reaction of Au into Ti3SiC2 single-crystal thin films with simultaneous out-diffusion of Si. Ti3IrC2 is subsequently produced by a substitution reaction of Ir for Au in Ti3Au2C2. These phases form Ohmic electrical contacts to SiC and remain stable after 1,000 h of ageing at 600 °C in air. The present results, by combined analytical electron microscopy and ab initio calculations, open avenues for processing of noble-metal-containing layered ceramics that have not been synthesized from elemental sources, along with tunable properties such as stable electrical contacts for high-temperature power electronics or gas sensors.

Potential for structural lumber substitutes

Treesearch

Theodore L. Laufenberg

1985-01-01

The potential for substitution of structural wood composites into solid-sawn lumber markets is presented from the technological viewpoint. Technological limitations of existing composite processes and products are reviewed in the context of the present laminated veneer lumber (LVL), flakeboard, and fiber/ paper industries. The limits of mechanical property potential...

Models for the dynamics of dust-like matter in the self-gravity field: The method of hydrodynamic substitutions

NASA Astrophysics Data System (ADS)

Zhuravlev, V. M.

2017-09-01

Models for the dynamics of a dust-like medium in the self-gravity field are investigated. Solutions of the corresponding problems are constructed by the method of hydrodynamic substitutions generalizing the Cole-Hopf substitutions. The method is extended to multidimensional ideal and viscous fluid flows with cylindrical and spherical symmetries for which exact solutions are constructed. Solutions for the dynamics of self-gravitating dust with arbitrary initial distributions of both fluid density and velocity are constructed using special coordinate transformations. In particular, the problem of cosmological expansion is considered in terms of Newton's gravity theory. Models of a one-dimensional viscous dust fluid flow and some problems of gas hydrodynamics are considered. Examples of exact solutions and their brief analysis are provided.

Pyrene Molecular Orbital Shuffle-Controlling Excited State and Redox Properties by Changing the Nature of the Frontier Orbitals.

PubMed

Merz, Julia; Fink, Julian; Friedrich, Alexandra; Krummenacher, Ivo; Al Mamari, Hamad H; Lorenzen, Sabine; Haehnel, Martin; Eichhorn, Antonius; Moos, Michael; Holzapfel, Marco; Braunschweig, Holger; Lambert, Christoph; Steffen, Andreas; Ji, Lei; Marder, Todd B

2017-09-21

We show that by judicious choice of substituents at the 2- and 7-positions of pyrene, the frontier orbital order of pyrene can be modified, giving enhanced control over the nature and properties of the photoexcited states and the redox potentials. Specifically, we introduced a julolidine-like moiety and Bmes 2 (mes=2,4,6-Me 3 C 6 H 2 ) as very strong donor (D) and acceptor (A), respectively, giving 2,7-D-π-D- and unsymmetric 2,7-D-π-A-pyrene derivatives, in which the donor destabilizes the HOMO-1 and the acceptor stabilizes the LUMO+1 of the pyrene core. Consequently, for 2,7-substituted pyrene derivatives, unusual properties are obtained. For example, very large bathochromic shifts were observed for all of our compounds, and unprecedented green light emission occurs for the D/D system. In addition, very high radiative rate constants in solution and in the solid state were recorded for the D-π-D- and D-π-A-substituted compounds. All compounds show reversible one-electron oxidations, and Jul 2 Pyr exhibits a second oxidation, with the largest potential splitting (ΔE=440 mV) thus far reported for 2,7-substituted pyrenes. Spectroelectrochemical measurements confirm an unexpectedly strong coupling between the 2,7-substituents in our pyrene derivatives. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

The enhancement in dielectric and magnetic property in Na and Mn co substituted lanthanum ferrite

NASA Astrophysics Data System (ADS)

Rai, Atma; Thakur, Awalendra K.

2016-05-01

Nanocrystalline solid solutions of La1-xNaxFe1-yMnyO3 (x=y=0.00 and 0.25) were prepared via modified Pechini route. No evidence of secondary or impurity phase has been detected up to the detection of error limit of high power X-ray diffractometer. Dielectric property of the samples has been investigated in the frequency range 100 Hz-4MHz at temperature ranging 300-450K. The value of relative permittivity (ɛr) increases drastically and shows colossal dielectric response (˜104) by cosubstitution of Na and Mn as compared to pure LaFeO3. Dielectric relaxation peak in loss tangent in both samples have been found and shift towards higher frequency region as temperature increases. Magnetization-Field (M-H) loop of the calcined sample have been recorded at room temperature (300K) at field ±60kOe. Magnetic property also enhanced by co substitution of Na and Mn. The change in Fe/Mn-O-Fe/Mn angle by co-substitution of Na and Mn in LaFeO3 and indirect exchange interaction between two different magnetic sub lattices Fe and Mn might be responsible for drastic change. Saturation/maximum magnetic moment increase ˜four times in LNFM25 (5.335emu/g) as compared to pure LaFeO3 (1.302emu/g).

Sequence-defined oligo(ortho-arylene) foldamers derived from the benzannulation of ortho(arylene ethynylene)s† †Electronic supplementary information (ESI) available. CCDC 1483959–1483967. For ESI and crystallographic data in CIF or other electronic format see DOI: 10.1039/c6sc02520j Click here for additional data file. Click here for additional data file.

PubMed Central

Lehnherr, Dan; Chen, Chen; Pedramrazi, Zahra; DeBlase, Catherine R.; Alzola, Joaquin M.; Keresztes, Ivan; Lobkovsky, Emil B.

2016-01-01

A Cu-catalyzed benzannulation reaction transforms ortho(arylene ethynylene) oligomers into ortho-arylenes. This approach circumvents iterative Suzuki cross-coupling reactions previously used to assemble hindered ortho-arylene backbones. These derivatives form helical folded structures in the solid-state and in solution, as demonstrated by X-ray crystallography and solution-state NMR analysis. DFT calculations of misfolded conformations are correlated with variable-temperature 1H and EXSY NMR to reveal that folding is cooperative and more favorable in halide-substituted naphthalenes. Helical ortho-arylene foldamers with specific aromatic sequences organize functional π-electron systems into arrangements ideal for ambipolar charge transport and show preliminary promise for the surface-mediated synthesis of structurally defined graphene nanoribbons. PMID:28567248

Calcium silicate hydrates: Solid and liquid phase composition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lothenbach, Barbara, E-mail: Barbara.lothenbach@empa.ch; Nonat, André

This paper presents a review on the relationship between the composition, the structure and the solution in which calcium silicate hydrate (C–S–H) is equilibrated. The silica chain length in C–S–H increases with the silicon concentration and the calcium content in the interlayer space with the calcium concentrations. Sodium and potassium are taken up in the interlayer space, preferentially at low calcium concentrations and thus by low Ca/Si C–S–H. Aluminium uptake in C–S–H increases strongly at higher aluminium concentrations in the solution. At low Ca/Si, aluminium substitutes silica in the bridging position, at Ca/Si > 1 aluminium is bound in TAH.more » Recently developed thermodynamic models are closely related to the structure of C–S–H and tobermorite, and able to model not only the solubility and the chemical composition of the C–S–H, but also to predict the mean silica chain length and the uptake of aluminium.« less

Hydration of Portland cement with additions of calcium sulfoaluminates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Le Saout, Gwenn, E-mail: gwenn.le-saout@mines-ales.fr; Lothenbach, Barbara; Hori, Akihiro

2013-01-15

The effect of mineral additions based on calcium aluminates on the hydration mechanism of ordinary Portland cement (OPC) was investigated using isothermal calorimetry, thermal analysis, X-ray diffraction, scanning electron microscopy, solid state nuclear magnetic resonance and pore solution analysis. Results show that the addition of a calcium sulfoaluminate cement (CSA) to the OPC does not affect the hydration mechanism of alite but controls the aluminate dissolution. In the second blend investigated, a rapid setting cement, the amorphous calcium aluminate reacts very fast to ettringite. The release of aluminum ions strongly retards the hydration of alite but the C-S-H has amore » similar composition as in OPC with no additional Al to Si substitution. As in CSA-OPC, the aluminate hydration is controlled by the availability of sulfates. The coupling of thermodynamic modeling with the kinetic equations predicts the amount of hydrates and pore solution compositions as a function of time and validates the model in these systems.« less

Oxygen nonstoichiometry and thermodynamic quantities in solid solution SrFe1-xSnxO3-δ

NASA Astrophysics Data System (ADS)

Merkulov, O. V.; Markov, A. A.; Leonidov, I. A.; Patrakeev, M. V.; Kozhevnikov, V. L.

2018-06-01

The oxygen content (3-δ) variations in tin substituted derivatives SrFe1-xSnxO3-δ, where x = 0.05, 0.1, 0.17 and 0.25, of perovskite-like strontium ferrite, have been studied by coulometric titration measurements within oxygen partial pressure (pO2) range 10-19-10-2 atm at 800-950 °С. The obtained dependencies of (3-δ) from pO2 and temperature are used for calculations of partial molar thermodynamic functions of oxygen in the oxide structure. It is found that a satisfactory explanation of the experimental results can be attained within frameworks of the ideal solution model with ion and electron defects appearing in the result of oxidation and disproportionation of iron cations. The increase of the oxidation reaction enthalpy with tin content is consistent with the increase of the unit cell parameter, i.e., the stretch and relaxation of Fe-O chemical bonds.

40 CFR 268.3 - Dilution prohibited as a substitute for treatment.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) The waste consists of organic, debris-like materials (e.g., wood, paper, plastic, or cloth... (CONTINUED) SOLID WASTES (CONTINUED) LAND DISPOSAL RESTRICTIONS General § 268.3 Dilution prohibited as a... restricted waste or the residual from treatment of a restricted waste as a substitute for adequate treatment...

40 CFR 268.3 - Dilution prohibited as a substitute for treatment.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) The waste consists of organic, debris-like materials (e.g., wood, paper, plastic, or cloth... (CONTINUED) SOLID WASTES (CONTINUED) LAND DISPOSAL RESTRICTIONS General § 268.3 Dilution prohibited as a... restricted waste or the residual from treatment of a restricted waste as a substitute for adequate treatment...

Effects of prevailing conditions during second Palestinian uprising on solid waste management system in Nablus city in Palestine.

PubMed

Arafat, Hassan A; Al-Khatib, Issam A; Zahra, Abdulsalam Abu

2006-08-01

Since the start of the second Palestinian uprising (Al-Aqsa Intifada), and due to the Israeli activities, curfews, closures, and military checkpoints imposed since 2000, the quality of social services rendered by Nablus city has been gradually deteriorating. Solid waste management in Nablus city was badly affected by these conditions, and this situation is negatively affecting health and damaging the environment. Most of these cases were due to reasons beyond the capability of the municipality with its limited resources. This study revealed that some of the important municipal solid waste (MSW) equipment had been damaged during the uprising. The workforce in the MSW system was reduced and certain MSW-related development projects and activities have been frozen due to the current conditions. The city's medical waste incinerator had been phased out and the number of special medical containers had been reduced from 16 to 10. Some MSW compressing trucks had been out of use with no substitute. Another important figure is the number of waste collection workers which decreased from 420 to 301, although the city is growing in premises as well as population. The created unsanitary solid waste transfer station is now a pollution source on its own, causing an ugly scene at the eastern entrance of Nablus city. There should be a comprehensive and urgent solution for this problem and the needed resources should be invested.

Structural manipulation approaches towards enhanced sodium ionic conductivity in Na-rich antiperovskites

DOE PAGES

Wang, Yonggang; Wang, Qingfei; Liu, Zhenpu; ...

2015-06-10

High-performance solid electrolytes are critical for realizing all-solid-state batteries with enhance safety and cycling efficiency. However, currently available candidates (sulfides and the NASICON-typ ceramics) still suffer from drawbacks such as inflammability, high-cost and unfavorable machinability Here we present the structural manipulation approaches to improve the sodium ionic conductivity in series of affordable Na-rich antiperovskites. Experimentally, the whole solid solutions of Na 3OX (X ¼ Cl Br, I) are synthesized via a facile and timesaving route from the cheapest raw materials (Na, NaOH an NaX). The materials are nonflammable, suitable for thermoplastic processing due to low melting temperature (<300° C) withoutmore » decomposing. Notably, owing to the flexibility of perovskite-type structure it's feasible to control the local structure features by means of size-mismatch substitution an unequivalent-doping for a favorable sodium ionic diffusion pathway. Enhancement of sodium ioni conductivity by 2 magnitudes is demonstrated by these chemical tuning methods. The optimized sodiu ionic conductivity in Na 2.9Sr 0.05OBr 0.6I 0.4 bulk samples reaches 1.9 10 - 3 S/cm at 200° C and even highe at elevated temperature. Here, we believe further chemical tuning efforts on Na-rich antiperovskites wil promote their performance greatly for practical all-solid state battery applications.« less

Structure refinements of members in the brownmillerite solid solution series Ca{sub 2}Al{sub x}(Fe{sub 0.5}Mn{sub 0.5}){sub 2-x}O{sub 5+{delta}} with 1/2{<=}x{<=}4/3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stoeber, Stefan, E-mail: stefan.stoeber@geo.uni-halle.de; Redhammer, Guenther; Schorr, Susan

2013-01-15

Four different brownmillerite solid solutions Ca{sub 2}Al{sub x}(Fe{sub 0.5}Mn{sub 0.5}){sub 2-x}O{sub 5+{delta}} with 1/2{<=}x{<=}4/3 were synthesized by a solid oxide ceramic method. The phases crystallize either in a primitive centered orthorhombic cell with space group Pnma or in a body centered cell with space group I2mb dependent on the aluminum concentration present in the solid solution. Mn{sup 3+} ions occupy exclusively site 4a coordinated by six oxygen anions. Increasing Mn{sup 3+} concentrations cause a remarkable distortion of the octahedron and indirectly of the tetrahedron, resulting in twisted and tilted octahedral layers as well as buckled tetrahedral chains. The influences aremore » discussed on the site 4a of trivalent manganese due to its Jahn-Teller activity, with regard to the occupation of octahedron and tetrahedron with different sized iron and aluminum ions. - Graphical Abstract: The coupled substitution Fe{sup 3+}>Mn{sup 3+}+Fe{sup 3+} <=>2 Al{sup 3+} in brownmillerite phases (Ca{sub 2}(Fe{sub 0.5}Mn{sub 0.5}){sub 2-x}Al{sub x}O{sub 5+{delta}}) changes predominantly their structural properties, which is essential for the hydration performance of the calcium aluminate cement, where brownmillerites occur as clinker phases. Highlights: Black-Right-Pointing-Pointer We present structural data of four Ca-Al-Fe-Mn-brownmillerites. Black-Right-Pointing-Pointer Mn{sup 3+}-ions occupy exclusively the octahedrally coordinated site 0,0,0. Black-Right-Pointing-Pointer Bonds and angles of the octahedrally coordinated site are distorted strongly. Black-Right-Pointing-Pointer Mn{sup 3+}-ions influence indirectly the shape of the tetrahedron. Black-Right-Pointing-Pointer Mn{sup 3+}-ions stabilize Pnma instead of I2mb in Ca-Al-Fe-Mn-brownmillerites.« less

Generic maintenance immunosuppression in solid organ transplant recipients.

PubMed

Ensor, Christopher R; Trofe-Clark, Jennifer; Gabardi, Steven; McDevitt-Potter, Lisa M; Shullo, Michael A

2011-11-01

Survival after solid organ transplantation has increased in the era of tacrolimus and mycophenolate. This increased survival could be due in part to the broad clinical use of these potent and specific agents for maintenance immunosuppression. These drugs have enhanced specificity and potency for T and B lymphocytes compared with their predecessors, cyclosporine and azathioprine. Between 2008 and 2010, the United States Food and Drug Administration approved several generic formulations of both tacrolimus and mycophenolate mofetil. Deciding whether generic products can be safely substituted for the innovator product is a clinical dilemma similar to that which occurred when generic formulations of cyclosporine became available. We describe the concerns regarding generic immunosuppression use, summarize expert opinion and consensus statements in transplantation, analyze the potential impact of generic substitution, and provide estimates of populations affected based on generic drug market penetration. Formulary considerations such as cost, availability, and potential drug ordering and drug selection errors are described, and transplant coordinator and patient perspectives are reviewed. Finally, general recommendations about the use of generic maintenance immunosuppression in solid organ transplant recipients are provided. Although more research is needed to confirm clinical and therapeutic equivalence and pharmacoeconomic benefit, generic immunosuppressants can be safely substituted for innovator products as long as patients consistently receive the same product, patients and clinicians are aware of when substitutions occur, and enhanced therapeutic drug monitoring is provided during the transition.

Improving the dissolution rate of poorly water soluble drug by solid dispersion and solid solution: pros and cons.

PubMed

Chokshi, Rina J; Zia, Hossein; Sandhu, Harpreet K; Shah, Navnit H; Malick, Waseem A

2007-01-01

The solid dispersions with poloxamer 188 (P188) and solid solutions with polyvinylpyrrolidone K30 (PVPK30) were evaluated and compared in an effort to improve aqueous solubility and bioavailability of a model hydrophobic drug. All preparations were characterized by differential scanning calorimetry, powder X-ray diffraction, intrinsic dissolution rates, and contact angle measurements. Accelerated stability studies also were conducted to determine the effects of aging on the stability of various formulations. The selected solid dispersion and solid solution formulations were further evaluated in beagle dogs for in vivo testing. Solid dispersions were characterized to show that the drug retains its crystallinity and forms a two-phase system. Solid solutions were characterized to be an amorphous monophasic system with transition of crystalline drug to amorphous state. The evaluation of the intrinsic dissolution rates of various preparations indicated that the solid solutions have higher initial dissolution rates compared with solid dispersions. However, after storage at accelerated conditions, the dissolution rates of solid solutions were lower due to partial reversion to crystalline form. The drug in solid dispersion showed better bioavailability in comparison to solid solution. Therefore, considering physical stability and in vivo study results, the solid dispersion was the most suitable choice to improve dissolution rates and hence the bioavailability of the poorly water soluble drug.

Anticancer Activity Expressed by a Library of 2,9-Diazaperopyrenium Dications

PubMed Central

2016-01-01

Polyaromatic compounds are well-known to intercalate DNA. Numerous anticancer chemotherapeutics have been developed upon the basis of this recognition motif. The compounds have been designed such that they interfere with the role of the topoisomerases, which control the topology of DNA during the cell-division cycle. Although many promising chemotherapeutics have been developed upon the basis of polyaromatic DNA intercalating systems, these candidates did not proceed past clinical trials on account of their dose-limiting toxicity. Herein, we discuss an alternative, water-soluble class of polyaromatic compounds, the 2,9-diazaperopyrenium dications, and report in vitro cell studies for a library of these dications. These investigations reveal that a number of 2,9-diazaperopyrenium dications show similar activities as doxorubicin toward a variety of cancer cell lines. Additionally, we report the solid-state structures of these dications, and we relate their tendency to aggregate in solution to their toxicity profiles. The addition of bulky substituents to these polyaromatic dications decreases their tendency to aggregate in solution. The derivative substituted with 2,6-diisopropylphenyl groups proved to be the most cytotoxic against the majority of the cell lines tested. In the solid state, the 2,6-diisopropylphenyl-functionalized derivative does not undergo π···π stacking, while in aqueous solution, dynamic light scattering reveals that this derivative forms very small (50–100 nm) aggregates, in contrast with the larger ones formed by dications with less bulky substituents. Alteration of the aromaticitiy in the terminal heterocycles of selected dications reveals a drastic change in the toxicity of these polyaromatic species toward specific cell lines. PMID:25555133

Fluorine substituted (Mn,Ir)O 2:F high performance solid solution oxygen evolution reaction electro-catalysts for PEM water electrolysis

DOE PAGES

Ghadge, Shrinath Dattatray; Patel, Prasad Prakash; Datta, Moni Kanchan; ...

2017-03-20

Identification and development of high performance with reduced overpotential (i.e. reduced operating electricity cost) oxygen evolution reaction (OER) electrocatalysts for proton exchange membrane (PEM) based water electrolysis with ultra-low noble metal content (i.e. reduced materials cost) is of significant interest for economic hydrogen production, thus increasing the commercialization potential of PEM water electrolysis. Accordingly, a novel electrocatalyst should exhibit low overpotential, excellent electrochemical activity and durability superior to state of the art noble metal based electro-catalysts (e.g. Pt, IrO 2, RuO 2). Here in this paper, for the very first time to the best of our knowledge, exploiting first-principles theoreticalmore » calculations of the total energies and electronic structures, we have identified a reduced noble metal content fluorine doped solid solution of MnO 2 and IrO 2, denoted as (Mn 1-xIr x)O 2:F (x = 0.2, 0.3, 0.4), OER electrocatalyst system exhibiting lower overpotential and higher current density than the state of the art IrO 2 and other previously reported systems for PEM water electrolysis. The doped solid solution displays an excellent electrochemical performance with a lowest reported onset potential to date of ~1.35 V (vs. RHE), ~80 mV lower than that of IrO 2 (~1.43 V vs. RHE) and ~15 fold (x = 0.3 and 0.4) higher electrochemical activity compared to pure IrO 2. In addition, the system displays excellent long term electrochemical durability, similar to that of IrO 2 in harsh acidic OER operating conditions. Our study therefore demonstrates remarkable, ~60–80% reduction in noble metal content along with lower overpotential and excellent electrochemical performance clearly demonstrating the potential of the (Mn 1-xIr x)O 2:F system as an OER electro-catalyst for PEM water electrolysis.« less

Fluorine substituted (Mn,Ir)O 2:F high performance solid solution oxygen evolution reaction electro-catalysts for PEM water electrolysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghadge, Shrinath Dattatray; Patel, Prasad Prakash; Datta, Moni Kanchan

Identification and development of high performance with reduced overpotential (i.e. reduced operating electricity cost) oxygen evolution reaction (OER) electrocatalysts for proton exchange membrane (PEM) based water electrolysis with ultra-low noble metal content (i.e. reduced materials cost) is of significant interest for economic hydrogen production, thus increasing the commercialization potential of PEM water electrolysis. Accordingly, a novel electrocatalyst should exhibit low overpotential, excellent electrochemical activity and durability superior to state of the art noble metal based electro-catalysts (e.g. Pt, IrO 2, RuO 2). Here in this paper, for the very first time to the best of our knowledge, exploiting first-principles theoreticalmore » calculations of the total energies and electronic structures, we have identified a reduced noble metal content fluorine doped solid solution of MnO 2 and IrO 2, denoted as (Mn 1-xIr x)O 2:F (x = 0.2, 0.3, 0.4), OER electrocatalyst system exhibiting lower overpotential and higher current density than the state of the art IrO 2 and other previously reported systems for PEM water electrolysis. The doped solid solution displays an excellent electrochemical performance with a lowest reported onset potential to date of ~1.35 V (vs. RHE), ~80 mV lower than that of IrO 2 (~1.43 V vs. RHE) and ~15 fold (x = 0.3 and 0.4) higher electrochemical activity compared to pure IrO 2. In addition, the system displays excellent long term electrochemical durability, similar to that of IrO 2 in harsh acidic OER operating conditions. Our study therefore demonstrates remarkable, ~60–80% reduction in noble metal content along with lower overpotential and excellent electrochemical performance clearly demonstrating the potential of the (Mn 1-xIr x)O 2:F system as an OER electro-catalyst for PEM water electrolysis.« less

CTEPP STANDARD OPERATING PROCEDURE FOR EXTRACTING AND PREPARING SOLID FOOD SAMPLES FOR ANALYSIS OF PERSISTENT ORGANIC POLLUTANTS (SOP-5.20)

EPA Science Inventory

This SOP describes the procedures for homogenizing, extracting and concentrating solid food samples for persistent organic pollutants such as organochlorine compounds, organophosphate compounds, polycyclic aromatic hydrocarbons, polychlorinated biphenyls, substituted phenols, and...

MUNICIPAL SOLID WASTE COMBUSTOR ASH DEMONSTRATION PROGRAM - "THE BOATHOUSE"

EPA Science Inventory

The report presents the results of a research program designed to examine the engineering and environmental acceptability of using municipal solid waste (MSW) combustor ash as an aggregate substitute in the manufacture of construction quality cement blocks. 50 tons of MSW combust...

Understanding the role of A-site and B-site cations on piezoelectric instability in lead--free (1-x) BaTiO3 -- xA(Cu1/3Nb2/3)O3 (A = Sr, Ca, Ba) solid solutions

NASA Astrophysics Data System (ADS)

Maurya, Deepam; Zhou, Yuan; Priya, Shashank

2013-03-01

This study provides fundamental understanding of the enhanced piezoelectric instability in lead-free piezoelectric (1-x) BaTiO3-xA(Cu1/3Nb2/3) O3(A: Sr, Ba and Ca and x = 0.0-0.03) solid solutions. These compositions were found to exhibit large longitudinal piezoelectric constant (d33) of ~330 pC/N and electromechanical planar coupling constant (kp) ~ 46% at room temperature. The X-ray diffraction coupled with atomic pair distribution functions (PDF)s indicated increase in local polarization. Raman scattering and electron paramagnetic resonance (EPR) analysis revealed that substitutions on A and B-site both substantially perturbed the local octahedral dynamics and resulted in localized nano polar regions with lower symmetry. The presence of nano domains and local structural distortions smears the Curie peak resulting in diffuse order-disorder type phase transitions. The effect of these distortions on the variations in physical property was modeled and analyzed within the context of nanodomains and phase transitions. *spriya@vt.edu The financial support from National Science Foundation and Office of Basic Energy Science, Department of Energy (Microscopy analysis) is gratefully acknowledged. The authors would also like to acknowledge the support from KIMS (new piezoelectric)

Green Perylene Bisimide Dyes: Synthesis, Photophysical and Electrochemical Properties

PubMed Central

Chang, Che-Wei; Tsai, Hsing-Yang; Chen, Kew-Yu

2014-01-01

Three asymmetric amino-substituted perylene bisimide dyes with different n-alkyl chain lengths (n = 6, 12, or 18), 1-(N,N-dialkylamino)perylene bisimides (1a–1c), were synthesized under mild condition in high yields and were characterized by 1H NMR, 13C NMR (nuclear magnetic resonance), HRMS (High Resolution Mass Spectrometer), UV-Vis and fluorescence spectra, as well as cyclic voltammetry (CV). These molecules show intense green color in both solution and solid state and are highly soluble in dichloromethane and even in nonpolar solvents, such as hexane. The shapes of the absorption spectra of 1a–1c in solid state and in solution were found to be virtually the same, indicating that the long alkyl chains could efficiently prevent aggregation. They exhibit a unique charge transfer emission in the near-infrared region, of which the peak wavelengths show strong solvatochromism. The dipole moments of the compounds have been estimated using the Lippert-Mataga equation, and upon excitation, they show larger dipole moment changes than that of 1-aminoperylene bisimide (2). Furthermore, all of the compounds exhibit two quasi-reversible one-electron oxidations and two quasi-reversible one-electron reductions in dichloromethane at modest potentials. Complementary density functional theory (DFT) calculations performed on these dyes are reported in order to rationalize their molecular structures and electronic properties. PMID:28788140

1,7-Bis-(N,N-dialkylamino)perylene Bisimides: Facile Synthesis and Characterization as Near-Infrared Fluorescent Dyes

PubMed Central

Chen, Kew-Yu; Chang, Che-Wei

2014-01-01

Three symmetric alkylamino-substituted perylene bisimides with different n-alkyl chain lengths (n = 6, 12, or 18), 1,7-bis-(N,N-dialkylamino)perylene bisimides (1a–1c), were synthesized under mild condition and were characterized by 1H NMR, 13C NMR and high resolution mass spectroscopy. Their optical and electrochemical properties were measured using UV-Vis and emission spectroscopic techniques as well as cyclic voltammetry (CV). These compounds show deep green color in both solution and solid state, and are highly soluble in dichloromethane and even in nonpolar solvents such as hexane. The shapes of the absorption spectra of 1a–1c in the solution and solid state were found to be almost the same, indicating that the long alkyl chains could efficiently prevent intermolecular contact and aggregation. They show a unique charge transfer emission in the near-infrared region, of which the peak wavelengths exhibit strong solvatochromism. The dipole moments of the molecules have been estimated using the Lippert–Mataga equation, and upon excitation, they show larger dipole moment changes than that of 1,7-diaminoperylene bisimide (2). Moreover, all the dyes exhibit two irreversible one-electron oxidations and two quasi-reversible one-electron reductions in dichloromethane at modest potentials. Complementary density functional theory calculations performed on these chromophores are reported in order to rationalize their electronic structure and optical properties. PMID:28788262

Anti-tumor effects and apoptosis induction by Realgar bioleaching solution in Sarcoma-180 cells in vitro and transplanted tumors in mice in vivo.

PubMed

Xie, Qin-Jian; Cao, Xin-Li; Bai, Lu; Wu, Zheng-Rong; Ma, Ying-Ping; Li, Hong-Yu

2014-01-01

Realgar which contains arsenic components has been used in traditional Chinese medicine (TCM) as an anticancer drug. However, neither Realgar nor its formula are soluble in water. As a result, high dose of Realgar has to be administered to achieve an effective blood medicine concentration, and this is associated with adverse side effects. The objective of the present study was to increase the solubility of a formula using hydrometallurgy technology as well as investigating its effects on in vitro and in vivo cell proliferation and apoptosis in Sarcoma-180 cell line. Antiproliferative activity of Realgar Bioleaching Solution (RBS) was evaluated by MTT assay. Further, effects of RBS on cell proliferation and apoptosis were studied using flow cytometry and transmission electron microscopy. Kunming mice were administered RBS in vivo, where arsenic specifically targeted solid tumors. The results indicated that RBS extract potently inhibited the tumor growth of Sarcoma-180 cell line in a dose-dependent manner. Flow cytometry and transmission electron microscopy further indicated that RBS significantly induced cell apoptosis through the inhibition of cell cycle pathway in a dose-dependent manner. Further, on RBS administration to mice, arsenic was specifically targeted to solid tumors RBS could substitute for traditional Realgar or its formula to work as a potent tool in cancer treatment.

Preparation and electrochemical properties of Zr-site substituted Li7La3(Zr2-xMx)O12 (M = Ta, Nb) solid electrolytes

NASA Astrophysics Data System (ADS)

Huang, Mian; Shoji, Mao; Shen, Yang; Nan, Ce-Wen; Munakata, Hirokazu; Kanamura, Kiyoshi

2014-09-01

Li7La3Zr2O12 (LLZ) solid electrolytes with Zr site partially substituted by Ta and Nb elements were prepared via the conventional solid-state reaction. All the compositions could lead to the cubic garnet-type structure after sintering at 1150 °C. The use of γ-Al2O3 as a sintering aid in the preparation of doped LLZ was studied. It was shown that Al could help to improve the micro-structure for Nb doping, but not necessary for Ta doping. The Ta and Nb doping enhanced the ionic conductivity at 25 °C to 4.09 × 10-4 S cm-1 and 4.50 × 10-4 S cm-1, respectively. A conductivity as high as 1.23 × 10-3 S cm-1 was obtained when measured at 50 °C in air for the Nb-doped LLZ. All-solid-state batteries with LLZTa and LLZNb solid electrolytes were assembled and tested. The cyclic voltammetry (CV) measurement indicated the successful working of the batteries.

Physical properties of ice cream containing milk protein concentrates.

PubMed

Alvarez, V B; Wolters, C L; Vodovotz, Y; Ji, T

2005-03-01

Two milk protein concentrates (MPC, 56 and 85%) were studied as substitutes for 20 and 50% of the protein content in ice cream mix. The basic mix formula had 12% fat, 11% nonfat milk solids, 15% sweetener, and 0.3% stabilizer/emulsifier blend. Protein levels remained constant, and total solids were compensated for in MPC mixes by the addition of polydextrose. Physical properties investigated included apparent viscosity, fat globule size, melting rate, shape retention, and freezing behavior using differential scanning calorimetry. Milk protein concentrate formulations had higher mix viscosity, larger amount of fat destabilization, narrower ice melting curves, and greater shape retention compared with the control. Milk protein concentrates did not offer significant modifications of ice cream physical properties on a constant protein basis when substituted for up to 50% of the protein supplied by nonfat dry milk. Milk protein concentrates may offer ice cream manufacturers an alternative source of milk solids non-fat, especially in mixes reduced in lactose or fat, where higher milk solids nonfat are needed to compensate other losses of total solids.

Growth of self-textured Ga3+-substituted Li7La3Zr2O12 ceramics by solid state reaction and their significant enhancement in ionic conductivity

NASA Astrophysics Data System (ADS)

Qin, Shiying; Zhu, Xiaohong; Jiang, Yue; Ling, Ming'en; Hu, Zhiwei; Zhu, Jiliang

2018-03-01

A highly self-textured Ga2O3-substituted Li7La3Zr2O12 (LLZO-Ga) solid electrolyte with a nominal composition of Li6.55Ga0.15La3Zr2O12 is obtained by a simple and low-cost solid-state reaction technique, requiring no seed crystals to achieve grain orientation. The as-prepared self-textured LLZO-Ga shows a strong (420) preferred orientation with a high Lotgering factor of 0.91. Coherently, a terrace-shaped microstructure consisting of many parallel layers, indicating a two-dimensional-like growth mode, is clearly observed in the self-textured sample. As a result, the highly self-textured garnet-type lithium-ion conducting solid electrolyte of LLZO-Ga exhibits an extremely high ionic conductivity, reaching a state-of-the-art level of 2.06 × 10-3 S cm-1 at room temperature (25 °C) and thus shedding light on an important strategy for improving the structure and ionic conductivity of solid electrolytes.

Amine enriched solid sorbents for carbon dioxide capture

DOEpatents

Gray, McMahan L.; Soong, Yee; Champagne, Kenneth J.

2003-04-15

A new method for making low-cost CO.sub.2 sorbents that can be used in large-scale gas-solid processes. The new method entails treating a solid substrate with acid or base and simultaneous or subsequent treatment with a substituted amine salt. The method eliminates the need for organic solvents and polymeric materials for the preparation of CO.sub.2 capture systems.

Structural, Electronic, and Optical Properties of BiOX1-xYx (X, Y = F, Cl, Br, and I) Solid Solutions from DFT Calculations.

PubMed

Zhao, Zong-Yan; Liu, Qing-Lu; Dai, Wen-Wu

2016-08-23

Six BiOX1-xYx (X, Y = F, Cl, Br, and I) solid solutions have been systematically investigated by density functional theory calculations. BiOCl1-xBrx, BiOBr1-xIx, and BiOCl1-xIx solid solutions have very small bowing parameters; as such, some of their properties increase almost linearly with increasing x. For BiOF1-xYx solid solutions, the bowing parameters are very large and it is extremely difficult to fit the related calculated data by a single equation. Consequently, BiOX1-xYx (X, Y = Cl, Br, and I) solid solutions are highly miscible, while BiOF1-xYx (Y = Cl, Br, and I) solid solutions are partially miscible. In other words, BiOF1-xYx solid solutions have miscibility gaps or high miscibility temperature, resulting in phase separation and F/Y inhomogeneity. Comparison and analysis of the calculated results and the related physical-chemical properties with different halogen compositions indicates that the parameters of BiOX1-xYx solid solutions are determined by the differences of the physical-chemical properties of the two halogen compositions. In this way, the large deviation of some BiOX1-xYx solid solutions from Vegard's law observed in experiments can be explained. Moreover, the composition ratio of BiOX1-xYx solid solutions can be measured or monitored using optical measurements.

Extractant composition

DOEpatents

Smith, Barbara F.; Jarvinen, Gordon D.; Ryan, Robert R.

1990-01-01

An organic extracting solution useful for separating elements of the actinide series of the periodic table from elements of the lanthanide series, where both are in trivalent form. The extracting solution consists of a primary ligand and a secondary ligand, preferably in an organic solvent. The primary ligand is a substituted monothio-1,3-dicarbonyl, which includes a substituted 4-acyl-2-pyrazolin-5-thione, such as 4-benzoyl-2,4-dihydro-5-methyl-2-phenyl-3H-pyrazol-3-thione (BMPPT). The secondary ligand is a substituted phosphine oxide, such as trioctylphosphine oxide (TOPO).

Effect of glycerol concentrations on the mechanical properties of additive manufactured porous calcium polyphosphate structures for bone substitute applications.

PubMed

Sheydaeian, Esmat; Vlasea, Mihaela; Woo, Ami; Pilliar, Robert; Hu, Eugene; Toyserkani, Ehsan

2017-05-01

This article addresses the effects of glycerol (GLY) concentrations on the mechanical properties of calcium polyphosphate (CPP) bone substitute structures manufactured using binder jetting additive manufacturing. To achieve this goal, nine types of water-based binder solutions were prepared with 10, 12.5, and 15 wt % GLY liquid-binding agent, mixed, respectively, with 0, 0.75, and 1.5 wt % ethylene glycol diacetate (EGD) flow enhancer. The print quality of each of the solutions was established quantitatively using an image processing algorithm. The print quality analysis narrowed down the solutions to three batches containing 1.5 wt % EGD and variable amount of GLY. These solutions were used to manufacture porous CPP bone substitute samples, which were characterized physically to determine shrinkage, porosity, microstructure, and compression strength. The 12.5 wt % GLY, 1.5 wt % EGD solution resulted in the highest mechanical strength after sintering (34.6 ± 5.8 MPa), illustrating similar mechanical properties when compared to previous studies (33.9 ± 6.3 MPa) of additively manufactured CPP bone substitutes using a commercially available binder. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 828-835, 2017. © 2016 Wiley Periodicals, Inc.

Synthesis, molecular structure and vibrational spectra of 1,3-bis(1-adamantyl)-2-phenylpropan-1,3-diones

NASA Astrophysics Data System (ADS)

Babjaková, Eva; Dastychová, Lenka; Hanulíková, Barbora; Kuřitka, Ivo; Nečas, Marek; Vašková, Hana; Vícha, Robert

2015-04-01

The interest in the oxo-enol tautomerism of 1,3-dioxo compounds is justified by their usefulness in many synthetic fields. A series of new 1,3-bis(1-adamantyl)propan-1,3-diones with a variably substituted phenyl ring at the C2 position was prepared either by the reaction of an appropriate Grignard reagent with adamatane-1-carbonyl chloride or by SEAr on the unsubstituted 1,3-bis(1-adamantyl)-2-phenylpropan-1,3-dione. In addition to the single crystal X-ray diffraction analysis of three of the prepared compounds, the experimental 1H and 13C NMR, IR and Raman spectroscopic data were assigned and compared to those obtained by DFT computations. In the solid state, the syn-dioxo forms were exclusively observed, which are shown to also predominate in CHCl3 solutions. The analysis of the Hirshfeld surface revealed that H⋯H and O⋯H contacts dominate the intermolecular interactions in the solid state, whereas π⋯π stacking plays a marginal role.

Single crystal structure analyses of scheelite-powellite CaW1-xMoxO4 solidsolutions and unique occurrence in Jisyakuyama skarn deposits

NASA Astrophysics Data System (ADS)

Yamashita, K.; Yoshiasa, A.; Miyazaki, H.; Tokuda, M.; Tobase, T.; Isobe, H.; Nishiyama, T.; Sugiyama, K.; Miyawaki, R.

2017-12-01

Jisyakuyama skarn deposit, Fukuchi, Fukuoka, Japan, shows a simple occurrenceformed by penetration of hot water into limestone cracks. A unique occurrence of scheelite-powellite CaW1-xMoxO4 minerals is observed in the skarn deposit. Many syntheticexperiments for scheelite-powellite solid solutions have been reported as research onfluorescent materials. In this system it is known that a complete continuous solid solution isformed even at room temperature. In this study, we have carried out the chemical analyses,crystal structural refinements and detail description of occurrence on scheelite-powelliteminerals. We have also attempted synthesis of single crystal of solid solution in a widecomposition range. The chemical compositions were determined by JEOL scanningelectron microscope and EDS, INCA system. We have performed the crystal structurerefinements of the scheelite-powellite CaW1-xMoxO4 solid solutions (x=0.0-1.0) byRIGAKU single-crystal structure analysis system RAPID. The R and S values are around0.0s and 1.03. As the result of structural refinements of natural products and many solidsolutions, we confirm that most large natural single crystals have compositions at bothendmembers, and large solid solution crystals are rare. The lattice constants, interatomicdistances and other crystallographic parameters for the solid solution change uniquely withcomposition and it was confirmed as a continuous solid solution. Single crystals of scheeliteendmember + powellite endmember + solid solution with various compositions form anaggregate in the deposit (Figure 1). Crystal shapes of powellite and scheelite arehypidiomorphic and allotriomorphic, respectively. Many solid solution crystals areaccompanied by scheelite endmember and a compositional gap is observed betweenpowellite and solid-solution crystals. The presence of several penetration solutions withsignificantly different W and Mo contents may be assumed. This research can be expectedto lead to giving restrictive conditions to elucidate the mineralization process. Figure1. Scheelite + Powellite + solid solution aggregate

Optical evidence for the spin-state disorder in LaCo1-x Rh x O3

NASA Astrophysics Data System (ADS)

Terasaki, Ichiro; Asai, Shinichiro; Taniguchi, Hiroki; Okazaki, Ryuji; Yasui, Yukio; Ikemoto, Yuka; Moriwaki, Taro

2017-06-01

We have measured the infrared reflectivity of single-crystalline samples of LaCo1-x Rh x O3 (x  =  0, 0.05 and 0.10) from 10 to 300 K from 0.05 to 0.15 eV. We find that the optical phonons of the Co-O stretching mode depend on temperature and the Rh content. Analysis with three Lorentz oscillators reveals that the spin state of Co3+ in LaCo1-x Rh x O3 can be understood in terms of a solid solution of low-spin- and high-spin-state Co3+ ions, and the substituted Rh ion retains some fraction of the high-spin Co3+ ions down to low temperature.

Influence of the applied potentials difference on structural and conductive properties of CoZnO nanotubes

NASA Astrophysics Data System (ADS)

Ibragimova, M. A.; Kozlovskiy, A. L.; Kenzhina, I. E.; Zdorovets, M. V.

2018-04-01

A series of CoZnO nanotubes was obtained by electrochemical deposition, with different atomic metal coefficients, due to a change in the applied potential difference. A systematic study of the morphology, structural and conductive properties of nanotubes was also carried out. It is established that the samples synthesized at the applied potentials difference of 1.5 and 1.75 V are three-component systems consisting of two oxide phases of ZnO and CoO1.92 cubic system and a phase of a solid solution of substitution Co0.65Zn0.35 of hexagonal type. The samples synthesized at a potential difference of 2.0 V represent an alloy of two oxide phases, ZnO and CoO1.92.

Synthesis, spectroscopic, and molecular structure characterizations of some azo derivatives of 2-hydroxyacetophenone

NASA Astrophysics Data System (ADS)

Albayrak, Çiğdem; Gümrükçüoğlu, İsmail E.; Odabaşoğlu, Mustafa; İskeleli, Nazan Ocak; Ağar, Erbil

2009-08-01

Some novel azo compounds were prepared by the reaction of 2-hydroxyacetophenone with aniline and its substituted derivatives. The structures of synthesized azo compounds were determined by IR, UV-Vis, 1H NMR and 13C NMR spectroscopic techniques and the structures of some of these compounds were also determined by X-ray diffraction studies. Structural analysis using IR in solid state shows that the azo form is favoured in the azo compounds whereas UV-Vis analysis of the azo compounds in solution has shown that there is a azo and ionic form. The azo compounds in the basic solvents dimethylformamide (DMF) and dimethylsulfoxide (DMSO) are both azo and ionic form while these compounds in ethyl alcohol (EtOH) and chloroform (CHCl 3) are only azo form.

Mechanosynthesis of A Ferritic ODS (Oxide Dispersion Strengthened) Steel Containing 14% Chromium and Its Characterization

NASA Astrophysics Data System (ADS)

Rivai, A. K.; Dimyati, A.; Adi, W. A.

2017-05-01

One of the advanced materials for application at high temperatures which is aggressively developed in the world is ODS (Oxide Dispersion strengthened) steel. ODS ferritic steels are one of the candidate materials for future nuclear reactors in the world (Generation IV reactors) because it is able to be used in the reactor above 600 °C. ODS ferritic steels have also been developed for the interconnect material of SOFC (Solid Oxide Fuel Cell) which will be exposed to about 800 °C of temperature. The steel is strengthened by dispersing homogeneously of oxide particles (ceramic) in nano-meter sized in the matrix of the steel. Synthesis of a ferritic ODS steel by dispersion of nano-particles of yttrium oxide (yttria: Y2O3) as the dispersion particles, and containing high-chromium i.e. 14% has been conducted. Synthesis of the ODS steels was done mechanically (mechanosynthesis) using HEM (High Energy ball Milling) technique for 40 and 100 hours. The resulted samples were characterized using SEM-EDS (Scanning Electron Microscope-Energy Dispersive Spectroscope), and XRD (X-ray diffraction) to analyze the microstructure characteristics. The results showed that the crystal grains of the sample with 100 hours milling time was much smaller than the sample with 40 hours milling time, and some amount of alloy was formed during the milling process even for 40 hours milling time. Furthermore, the structure analysis revealed that some amount of iron atom substituted by a slight amount of chromium atom as a solid solution. The quantitative analysis showed that the phase mostly consisted of FeCr solid-solution with the structure was BCC (body-centered cubic).

Hybrid photoluminescent materials containing a benzobisthiazole core for liquid crystal and gel applications.

PubMed

Díaz, E; Elgueta, E; Sanchez, S A; Barberá, J; Vergara, J; Parra, M; Dahrouch, M

2017-03-01

Tetra- and hexacatenar amide compounds containing a linear centrosymmetric benzobisthiazole core were synthesized with good yields. These compounds were characterized and their structures confirmed by elemental analysis, and FT-IR, Maldi mass and NMR spectroscopy. All compounds exhibited excellent thermal stability up to 330 °C. The tetracatenar series containing a double substitution in the meta positions did not show mesomorphic behaviour, whereas the hexacatenar and tetracatenar series having a double substitution in the meta and para positions showed liquid crystal properties with optical textures typical of columnar mesophases corroborated by POM analysis. The mesomorphic properties were dependent on the length, number and position of alkoxy chains attached at the end of the rigid core. XRD studies of the hexacatenar series showed the hexagonal columnar structure of the mesophases. Photoluminescence properties in solution were observed in the visible region, with good quantum yields. In the solid state, these compounds behave as blue emitters and they are able to change colour with acid or base addition. The hexacatenar benzobisthiazole compound with an alkoxy chain of 14 carbons presented properties of a supergelator in chloroform, leading to the formation of a fluorescent organogel material with fluorescence emission in the blue region.

Structural and magnetic properties of SrMn1-xRuxO3 perovskites

NASA Astrophysics Data System (ADS)

Dabrowski, B.; Kolesnik, S.; Chmaissem, O.; Maxwell, T.

2007-03-01

Ferromagnetism of SrRuO3 is unique among 4d transition metal based perovskite oxides. On substitution of Mn its TC decreases from 163 K to 0 for x˜0.5-0.6 followed by a formation of an antiferromagnetic insulating state at a quantum critical point. The other end member of the SrMn1-xRuxO3 family, a cubic perovskite SrMnO3 is a G-type antiferromagnet with TN=233 K. We have synthesized the complete SrMn1-xRuxO3 solid solution. The polycrystalline samples were characterized by neutron difraction, magnetic, and transport experiments. The incorporation of Ru in the SrMnO3 matrix (0.1<=x<=0.4) results in a phase transition to a C-type antiferromagnetic state accompanied by a cubic-tetragonal transition. The intermediate substitution level induces a spin-glass behavior, due to competing ferro- and antiferromagnetic interactions. Mixed valence Mn^3+/Mn^4+ and Ru^4+/Ru^5+ pairs introduce additional frustration to the magnetic states. The glassy behavior can be observed for x up to 0.7 in the tetragonal structure. Supported by NSF (DMR-0302617) and the U.S. Department of Education

Ce3 - xMgxCo9 : Transformation of a Pauli Paramagnet into a Strong Permanent Magnet

NASA Astrophysics Data System (ADS)

Lamichhane, Tej N.; Taufour, Valentin; Palasyuk, Andriy; Lin, Qisheng; Bud'ko, Sergey L.; Canfield, Paul C.

2018-02-01

We report on the synthesis of single-crystal and polycrystalline samples of Ce3 -xMgxCo9 solid solution (0 ≤x ≲1.4 ) and characterization of their structural and magnetic properties. The crystal structure remains rhombohedral in the whole composition range and Mg partially replaces Ce in the 6 c site of the CeCo3 structure. Ferromagnetism is induced by Mg substitutions starting as low as x =0.18 and reaching a Curie temperature as high as 450 K for x =1.35 . Measurements on single crystals with x =1.34 and TC=440 K indicate an axial magnetic anisotropy with an anisotropy field of 6 T and a magnetization of 6 μB/f .u . at 300 K. Coercicity is observed in the polycrystalline samples consistent with the observed axial magnetic anisotropy. Our discovery of ferromagnetism with large axial magnetic anisotropy induced by substituting a rare-earth element by Mg is a very promising result in the search of inexpensive permanent-magnet materials and suggests that other nonmagnetic phases, similar to CeCo3 , may also conceal nearby ferromagnetic phases.

Cell dimensions and antiferromagnetism of lunar and terrestrial ilmenite single crystals

USGS Publications Warehouse

Thorpe, A.N.; Minkin, J.A.; Senftle, F.E.; Alexander, Corrine; Briggs, Charles; Evans, H.T.; Nord, G.L.

1977-01-01

X-Ray diffraction and anisotropic magnetic measurements have been made on single crystals of lunar ilmenite and on terrestrial ilmenite from Bancroft, Ontario, Canada and the Ilmen Mountains, U.S.S.R. The elongated c-axis of lunar ilmenite, previously reported, is confirmed by new measurements. The shorter c-axis found in terrestrial specimens is ascribed to Fe3+ substitution for Ti4+ in the titanium layer. Magnetic measurements on the same specimens show that, in agreement with the Ishikawa-Shirane et al. model, the initial shortening of the c-axis by the above substitution of small amounts of Fe3+ (<8%) causes an increase in Fe2+-Fe2+ exchange coupling through Fe3+ in the titanium layer that lowers the Ne??el transition temperature. The Weiss temperatures and other magnetic parameters confirm this model proposed by Ishikawa and Shirane et al. Additional transitions found in one of the terrestrial specimens (Bancroft) have been ascribed to a small amount of an exsolved spinel phase, possibly a solid solution phase of magnetite-u??lvospinel. The spinel phase is localized in hematite-rich blebs which exsolved from the host ilmenite-rich phase. ?? 1977.

Ce 3 - x Mg x Co 9 : Transformation of a Pauli Paramagnet into a Strong Permanent Magnet

DOE PAGES

Lamichhane, Tej N.; Taufour, Valentin; Palasyuk, Andriy; ...

2018-02-23

In this article we report on the synthesis of single-crystal and polycrystalline samples of Ce 3-xMg xCo 9 solid solution (0 ≤ x ≲ 1.4) and characterization of their structural and magnetic properties. The crystal structure remains rhombohedral in the whole composition range and Mg partially replaces Ce in the 6c site of the CeCo 3 structure. Ferromagnetism is induced by Mg substitutions starting as low as x = 0.18 and reaching a Curie temperature as high as 450 K for x = 1.35 . Measurements on single crystals with x = 1.34 and T C = 440 K indicatemore » an axial magnetic anisotropy with an anisotropy field of 6 T and a magnetization of 6 μ B/f.u. at 300 K. Coercicity is observed in the polycrystalline samples consistent with the observed axial magnetic anisotropy. Our discovery of ferromagnetism with large axial magnetic anisotropy induced by substituting a rare-earth element by Mg is a very promising result in the search of inexpensive permanent-magnet materials and suggests that other nonmagnetic phases, similar to CeCo 3, may also conceal nearby ferromagnetic phases.« less

Ce 3 - x Mg x Co 9 : Transformation of a Pauli Paramagnet into a Strong Permanent Magnet

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lamichhane, Tej N.; Taufour, Valentin; Palasyuk, Andriy

In this article we report on the synthesis of single-crystal and polycrystalline samples of Ce 3-xMg xCo 9 solid solution (0 ≤ x ≲ 1.4) and characterization of their structural and magnetic properties. The crystal structure remains rhombohedral in the whole composition range and Mg partially replaces Ce in the 6c site of the CeCo 3 structure. Ferromagnetism is induced by Mg substitutions starting as low as x = 0.18 and reaching a Curie temperature as high as 450 K for x = 1.35 . Measurements on single crystals with x = 1.34 and T C = 440 K indicatemore » an axial magnetic anisotropy with an anisotropy field of 6 T and a magnetization of 6 μ B/f.u. at 300 K. Coercicity is observed in the polycrystalline samples consistent with the observed axial magnetic anisotropy. Our discovery of ferromagnetism with large axial magnetic anisotropy induced by substituting a rare-earth element by Mg is a very promising result in the search of inexpensive permanent-magnet materials and suggests that other nonmagnetic phases, similar to CeCo 3, may also conceal nearby ferromagnetic phases.« less

Toluene nitration in irradiated nitric acid and nitrite solutions

NASA Astrophysics Data System (ADS)

Elias, Gracy; Mincher, Bruce J.; Mezyk, Stephen P.; Muller, Jim; Martin, Leigh R.

2011-04-01

The kinetics, mechanisms, and stable products produced for the nitration of aryl alkyl mild ortho-para director toluene in irradiated nitric acid and neutral nitrite solutions were investigated using γ and pulse radiolysis. Electron pulse radiolysis was used to determine the bimolecular rate constants for the reaction of toluene with different transient species produced by irradiation. HPLC with UV detection, GC-MS and LC-MS, were used to assess the stable reaction products. Free-radical based nitration reaction products were found in irradiated acidic and neutral media. In 6.0 M HNO3, ring substitution, side chain substitution, and oxidation, produced different nitrated toluene products. For ring substitution, nitrogen oxide radicals were added mainly to cyclohexadienyl radicals, whereas for side chain substitution, these radicals were added to the carbon-centered benzyl radical produced by H-atom abstraction. In neutral nitrite solutions, radiolytically-induced ring nitration products approached a statistically random distribution, suggesting a direct free-radical reaction involving addition of the rad NO2 radical.

Mixed oxide solid solutions

DOEpatents

Magno, Scott; Wang, Ruiping; Derouane, Eric

2003-01-01

The present invention is a mixed oxide solid solution containing a tetravalent and a pentavalent cation that can be used as a support for a metal combustion catalyst. The invention is furthermore a combustion catalyst containing the mixed oxide solid solution and a method of making the mixed oxide solid solution. The tetravalent cation is zirconium(+4), hafnium(+4) or thorium(+4). In one embodiment, the pentavalent cation is tantalum(+5), niobium(+5) or bismuth(+5). Mixed oxide solid solutions of the present invention exhibit enhanced thermal stability, maintaining relatively high surface areas at high temperatures in the presence of water vapor.

Separation of actinides from lanthanides

DOEpatents

Smith, B.F.; Jarvinen, G.D.; Ryan, R.R.

1988-03-31

An organic extracting solution and an extraction method useful for separating elements of the actinide series of the periodic table from elements of the lanthanide series, where both are in trivalent form is described. The extracting solution consists of a primary ligand and a secondary ligand, preferably in an organic solvent. The primary ligand is a substituted monothio-1,3-dicarbonyl, which includes a substituted 4-acyl-2-pyrazolin-5-thione, such as 4-benzoyl-2,4- dihydro-5-methyl-2-phenyl-3H-pyrazol-3-thione (BMPPT). The secondary ligand is a substituted phosphine oxide, such as trioctylphosphine oxide (TOPO).

Separation of actinides from lanthanides

DOEpatents

Smith, Barbara F.; Jarvinen, Gordon D.; Ryan, Robert R.

1989-01-01

An organic extracting solution and an extraction method useful for separating elements of the actinide series of the periodic table from elements of the lanthanide series, where both are in trivalent form. The extracting solution consists of a primary ligand and a secondary ligand, preferably in an organic solvent. The primary ligand is a substituted monothio-1,3-dicarbonyl, which includes a substituted 4-acyl-2-pyrazolin-5-thione, such as 4-benzoyl-2,4-dihydro-5-methyl-2-phenyl-3H-pyrazol-3-thione (BMPPT). The secondary ligand is a substituted phosphine oxide, such as trioctylphosphine oxide (TOPO).

The enhancement in dielectric and magnetic property in Na and Mn co substituted lanthanum ferrite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rai, Atma, E-mail: atma@iitp.ac.in; Thakur, Awalendra K., E-mail: akt@iitp.ac.in; Centre for Energy and Environment Indian Institute of Technology Patna 800013 India

2016-05-06

Nanocrystalline solid solutions of La{sub 1-x}Na{sub x}Fe{sub 1-y}Mn{sub y}O{sub 3} (x=y=0.00 and 0.25) were prepared via modified Pechini route. No evidence of secondary or impurity phase has been detected up to the detection of error limit of high power X-ray diffractometer. Dielectric property of the samples has been investigated in the frequency range 100 Hz-4MHz at temperature ranging 300–450K. The value of relative permittivity (ε{sub r}) increases drastically and shows colossal dielectric response (∼10{sup 4}) by cosubstitution of Na and Mn as compared to pure LaFeO{sub 3}. Dielectric relaxation peak in loss tangent in both samples have been found and shiftmore » towards higher frequency region as temperature increases. Magnetization-Field (M-H) loop of the calcined sample have been recorded at room temperature (300K) at field ±60kOe. Magnetic property also enhanced by co substitution of Na and Mn. The change in Fe/Mn-O-Fe/Mn angle by co-substitution of Na and Mn in LaFeO{sub 3} and indirect exchange interaction between two different magnetic sub lattices Fe and Mn might be responsible for drastic change. Saturation/maximum magnetic moment increase ∼four times in LNFM25 (5.335emu/g) as compared to pure LaFeO{sub 3} (1.302emu/g).« less

Influence of the manganese and cobalt content on the electrochemical performance of P2-Na0.67MnxCo1-xO2 cathodes for sodium-ion batteries.

PubMed

Hemalatha, K; Jayakumar, M; Prakash, A S

2018-01-23

The resurgence of sodium-ion batteries in recent years is due to their potential ability to form intercalation compounds possessing a high specific capacity and energy density comparable to existing lithium systems. To comprehend the role of cobalt substitution in the structure and electrochemical performance of Na 0.67 MnO 2 , the solid solutions of P2-Na 0.67 Mn x Co 1-x O 2 (x = 0.25, 0.5, 0.75) are synthesized and characterized. The XRD-Rietveld analysis revealed that the Co-substitution in Na 0.67 MnO 2 decreases lattice parameters 'a' and 'c' resulting in the contraction of MO 6 octahedra and the enlargement of inter-layer 'd' spacing. XPS indicates that the isovalent cobalt substitution in Na 0.67 MnO 2 results in the partial/complete replacement of Jahn-Teller active trivalent manganese to form low-spin complexes of better structural stability. The Na-ion diffusion coefficient, D Na + , derived from cyclic voltammetry and impedance spectroscopy, confirmed the enhanced mass transport in Co-rich phases compared to Mn-rich phases. Furthermore, higher diffusion coefficient values are observed for Co 3+ /Co 4+ than for their Mn 3+ /Mn 4+ redox processes. In addition, Co-rich phases exhibit a high structural stability and superior capacity retention, whereas Mn-rich phases discharge higher capacities.

Solid fat content as a substitute for total polar compound analysis in edible oils

USDA-ARS?s Scientific Manuscript database

The solid fat contents (SFC) of heated edible oil samples were measured and found to correlate positively with total polar compounds (TPC) and inversely with triglyceride concentration. Traditional methods for determination of total polar compounds require a laboratory setting and are time intensiv...

Ethanol production from food waste at high solid contents with vacuum recovery technology

USDA-ARS?s Scientific Manuscript database

Ethanol production from food wastes does not only solve the environmental issues but also provide renewable biofuel to partially substitute fossil fuels. This study investigated the feasibility of utilization of food wastes for producing ethanol at high solid contents (35%, w/w). Vacuum recovery sys...

Synthesis and structural studies on cerium substituted La0.4Ca0.6MnO3 as solid oxide fuel cell electrode material

NASA Astrophysics Data System (ADS)

Singh, Monika; Kumar, Dinesh; Singh, Akhilesh Kumar

2018-04-01

For solid oxide fuel cell electrode material, calcium doped lanthanum manganite La0.4Ca0.6MnO3 (LCMO) and cerium-incorporated on Ca-site with composition La0.40Ca0.55Ce0.05MnO3 (LCCMO) were synthesized using most feasible and efficient glycine-nitrate method. The formation of crystalline single phase was confirmed by x-ray diffraction (XRD). The Rietveld analysis reveals that both systems crystallize into orthorhombic crystal structure with Pnma space group. Additionally, 8 mole % Y2O3 stabilized ZrO2 (8YSZ) solid electrolyte was also synthesized using high energy ball mill to check the reaction with electrode materials. It was found that the substitution of Ce+4 cations in LCMO perovskite suppressed formation of undesired insulating CaZrO3 phase.

Chevrel-phase solid solution Mo 6Se 8- xTe x. Study of its superconducting, magnetic and NMR properties

NASA Astrophysics Data System (ADS)

Hamard1a, C.; Auffret, V.; Peña, O.; Le Floch, M.; Nowak, B.; Wojakowski, A.

2000-09-01

The Chevrel-phase solid solution Mo 6Se 8-Mo 6Te 8 was studied by X-ray diffraction, AC and DC magnetic susceptibility and 77Se and 125Te NMR spectroscopy. From the smooth evolution of the lattice parameters and superconducting critical temperatures, a progressive substitution of selenium atoms by tellurium is shown, on the whole range of composition 0⩽ x⩽8, in the formulation Mo 6Se 8- xTe x: the unit-cell volume increases linearly because of the larger ionic size of tellurium, while Tc decreases rapidly (from 6.45 down to 0 K) because of the different formal oxidation states of the anions and a probable evolution of the Fermi level in the density of states. Results of magnetic susceptibility support this model and suggest the inhibition of the intrinsic metallic behavior with increasing x. The NMR spectra of the binaries Mo 6Se 8 and Mo 6Te 8 reveal two significant features, attributed to two different chalcogen positions in the R 3¯ symmetry. At low Se contents in Mo 6Se 8- xTe x ( x=7.5, 7 and 6), selenium first fills the two X(2) sites along the three-fold axis (2c positions), and then it becomes statistically distributed over the general 6f positions, leading to broad 77Se NMR lines. On the other hand, substitution of Te atoms in Mo 6Se 8 seems to occur in a random way, creating large perturbations on the 125Te NMR spectra, over the whole range of x. Theoretical analysis based on the presence of two anisotropic lines (of axial and non-axial symmetries, respectively) allowed us to estimate their anisotropy factors and to perfectly simulate the frequency response of both Mo 6Se 8 and Mo 6Te 8 binaries. Analysis of the Knight shift anisotropy leads us to conclude about the importance of the molybdenum z 2 molecular orbital contribution which controls the Mo-X dipolar interactions.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grebenkemper, Jason H.; Hu, Yufei; Abdusalyamova, M.N.

Single crystals of Yb{sub 14−x}RE{sub x}MnSb{sub 11} (x~0.1, 0.4; RE = Tb, Dy, Ho) have been prepared as a solid solution by Sn flux reactions of the elements. They crystallize in the Ca{sub 14}AlSb{sub 11} structure type in the I4{sub 1}/acd space group. The RE{sup 3+}preferentially substitutes on the Yb(1) site which is the smallest volume Yb containing polyhedron. In the case of Ho{sup 3+}, a small amount of Ho{sup 3+} also substitutes on the Yb(4) site. The ferromagnetic ordering temperature of Yb{sub 14}MnSb{sub 11} is reduced from 53 K to 41 K as x increases and dependent on themore » identity of the RE. This is attributed to the reduction in carriers and reduced screening of the Mn{sup 2+} local moment. The effective moments, μ{sub eff,} agree well with the calculated moments assuming the RE substitutes as a trivalent cation. The largest coercive field is observed for RE = Dy (1000 Oe). For the maximum x of Yb{sub 14−x}RE{sub x}MnSb{sub 11} there are enough carriers for the Ruderman-Kittel-Kasuya-Yosida (RKKY) mechanism of magnetic coupling via conduction electrons to still be valid in describing the ferromagnetic ordering. - Graphical abstract: Field dependent susceptibility loops revealed magnetic remanence in these materials, which has not been previously observed in Yb{sub 14}MnSb{sub 11} compounds. The coercive field increases with the strength of the paramagnetic moment for the substituting rare earth and the amount of the rare earth that is substituted. Display Omitted - Highlights: • Yb{sub 14−x}RE{sub x}MnSb{sub 11} (RE=Tb, Dy, & Ho) were synthesized with x~0.2 and x~0.4. • Tb, Dy, & Ho preferentially substitute on the Yb(1) site. • Samples with the largest x and largest RE moment have the largest coercive field. • There is a split between zero field cooled and field cooled susceptibility.« less

Synthetic, Infrared, 1H and 13C NMR Spectral Studies on N-(2-/3-Substituted Phenyl)-4-Substituted Benzenesulphonamides, 4-X'C6H4SO2NH(2-/3-XC6H4), where X' = H, CH3, C2H5, F, Cl or Br, and X = CH3 or Cl

NASA Astrophysics Data System (ADS)

Gowda, B. Thimme; Shetty, Mahesha; Jayalakshmi, K. L.

2005-02-01

Twenty three N-(2-/3-substituted phenyl)-4-substituted benzenesulphonamides of the general formula, 4-X'C6H4SO2NH(2-/3-XC6H4), where X' = H, CH3, C2H5, F, Cl or Br and X = CH3 or Cl have been prepared and characterized, and their infrared spectra in the solid state, 1H and 13C NMR spectra in solution were studied. The N-H stretching vibrations, νN-H, absorb in the range 3285 - 3199 cm-1, while the asymmetric and symmetric SO2 vibrations vary in the ranges 1376 - 1309 cm-1 and 1177 - 1148 cm-1, respectively. The S-N and C-N stretching vibrations absorb in the ranges 945 - 893 cm-1 and 1304 - 1168 cm-1, respectively. The compounds do not exhibit particular trends in the variation of these frequencies on substitution either at ortho or meta positions with either a methyl group or Cl. The observed 1H and 13C chemical shifts of are assigned to protons and carbons of the two benzene rings. Incremental shifts of the ring protons and carbons due to -SO2NH(2-/3-XC6H4) groups in C6H5SO2NH(2-/3-XC6H4), and 4- X'C6H4SO2- and 4-X'C6H4SO2NH- groups in 4-X'C6H4SO2NH(C6H5) are computed and employed to calculate the chemical shifts of the ring protons and carbons in the substituted compounds, 4-X'C6H4SO2NH(2-/3-XC6H4). The computed values agree well with the observed chemical shifts.

Structural, thermodynamic, and mechanical properties of WCu solid solutions

NASA Astrophysics Data System (ADS)

Liang, C. P.; Wu, C. Y.; Fan, J. L.; Gong, H. R.

2017-11-01

Various properties of Wsbnd Cu solid solutions are systematically investigated through a combined use of first-principles calculation, cluster expansion, special quasirandom structures (SQS), and lattice dynamics. It is shown that SQS are effective to unravel the intrinsic nature of solid solutions, and that BCC and FCC W100-xCux solid solutions are energetically more stable when 0 ≤ x ≤ 70 and 70 < x ≤ 100, respectively. Calculations also reveal that the Debye model should be appropriate to derive thermodynamic properties of Wsbnd Cu, and that the coefficients of thermal expansion of W100-xCux solid solutions are much lower than those of corresponding mechanical mixtures. In addition, the G/B values of W100-xCux solid solutions reach a minimum at x = 50, which is fundamentally due to the softening of phonons as well as strong chemical bonding between W and Cu with a mainly metallic feature.

Designed synthesis and supramolecular architectures of furan-substituted perylene diimide.

PubMed

Yu, Yanwen; Li, Yongjun; Qin, Zhihong; Jiang, Runsheng; Liu, Huibiao; Li, Yuliang

2013-06-01

Novel furan-substituted perylene diimides are successfully synthesized and an efficient supramolecular architecture approach to construct zero/one-dimensional nano- and micro-structures by controlling solvents has been demonstrated. The aggregate structure conversion in different molecular structures can be controlled in the form of sphere-like, rod-like, and vesicle-like structures. As expected, these solid supramolecular rod-like architectures displayed interesting optical waveguide behavior, which indicates the aggregate structure materials of furan-substituted perylene diimides have the potential application as micro-scale photonic elements. Copyright © 2013 Elsevier Inc. All rights reserved.

Rheology of lyocell solutions from different cellulosic sources and development of regenerated cellulosic microfibers

NASA Astrophysics Data System (ADS)

Li, Zuopan

2003-10-01

The primary goals of the study were to develop manufactured cellulosic fibers and microfibers from wood pulps as well as from lignocellulosic agricultural by-products and to investigate alternative cellulosic sources as raw materials for lyocell solutions. A protocol was developed for the lyocell preparation from different cellulose sources. The cellulose sources included commercial dissolving pulps, commercial bleached hardwood, unbleached hardwood, bleached softwood, unbleached softwood, bleached thermomechanical pulp, unbleached thermomechanical pulp, bleached recycled newsprint, unbleached recycled newsprint, bagasse and kudzu. The rheological behavior of solutions was characterized. Complex viscosities and effective elongational viscosities were measured and the influences of parameters such as cellulose source, concentration, bleaching, and temperature were studied. One-way ANOVA post hoc tests were carried out to identify which cellulose sources have the potential to produce lyocell solutions having similar complex viscosities to those from commercial dissolving pulps. Lyocell solutions from both bleached and unbleached softwood and hardwood were classified as one homogenous subset that had the lowest complex viscosity. Kudzu solutions had the highest complex viscosity. The results showed the potential to substitute DP 1457 dissolving pulp with unbleached recycled newsprint pulps, to substitute DP 1195 dissolving pulp with bleached and unbleached thermomechanical pulps, to substitute DP 932 dissolving pulp with bleached thermomechanical pulps or bleached recycled newsprint pulps, to substitute DP 670 dissolving pulp with bagasse. Lyocell fibers were produced from selected solutions and were treated to produce microfibers. Water, sulfuric acid solutions and sodium hydroxide solutions were used. The treatment of lyocell fibers in 17.5% NaOH solutions for five minutes at 20°C successfully broke the fibers into fibrils along fiber axis. The diameters of the fibrils were generally in the range of 2 to 6 mum, and there were also finer fibrils with diameters less than 1 mum.

Conversion of depleted uranium hexafluoride to a solid uranium compound

DOEpatents

Rothman, Alan B.; Graczyk, Donald G.; Essling, Alice M.; Horwitz, E. Philip

2001-01-01

A process for converting UF.sub.6 to a solid uranium compound such as UO.sub.2 and CaF. The UF.sub.6 vapor form is contacted with an aqueous solution of NH.sub.4 OH at a pH greater than 7 to precipitate at least some solid uranium values as a solid leaving an aqueous solution containing NH.sub.4 OH and NH.sub.4 F and remaining uranium values. The solid uranium values are separated from the aqueous solution of NH.sub.4 OH and NH.sub.4 F and remaining uranium values which is then diluted with additional water precipitating more uranium values as a solid leaving trace quantities of uranium in a dilute aqueous solution. The dilute aqueous solution is contacted with an ion-exchange resin to remove substantially all the uranium values from the dilute aqueous solution. The dilute solution being contacted with Ca(OH).sub.2 to precipitate CaF.sub.2 leaving dilute NH.sub.4 OH.

pH-dependent equilibrium isotope fractionation associated with the compound specific nitrogen and carbon isotope analysis of substituted anilines by SPME-GC/IRMS.

PubMed

Skarpeli-Liati, Marita; Turgeon, Aurora; Garr, Ashley N; Arnold, William A; Cramer, Christopher J; Hofstetter, Thomas B

2011-03-01

Solid-phase microextraction (SPME) coupled to gas chromatography/isotope ratio mass spectrometry (GC/IRMS) was used to elucidate the effects of N-atom protonation on the analysis of N and C isotope signatures of selected aromatic amines. Precise and accurate isotope ratios were measured using polydimethylsiloxane/divinylbenzene (PDMS/DVB) as the SPME fiber material at solution pH-values that exceeded the pK(a) of the substituted aniline's conjugate acid by two pH-units. Deviations of δ(15)N and δ(13)C-values from reference measurements by elemental analyzer IRMS were small (<0.9‰) and within the typical uncertainties of isotope ratio measurements by SPME-GC/IRMS. Under these conditions, the detection limits for accurate isotope ratio measurements were between 0.64 and 2.1 mg L(-1) for δ(15)N and between 0.13 and 0.54 mg L(-1) for δ(13)C, respectively. Substantial inverse N isotope fractionation was observed by SPME-GC/IRMS as the fraction of protonated species increased with decreasing pH leading to deviations of -20‰ while the corresponding δ(13)C-values were largely invariant. From isotope ratio analysis at different solution pHs and theoretical calculations by density functional theory, we derived equilibrium isotope effects, EIEs, pertinent to aromatic amine protonation of 0.980 and 1.001 for N and C, respectively, which were very similar for all compounds investigated. Our work shows that N-atom protonation can compromise accurate compound-specific N isotope analysis of aromatic amines.

Synthesis and Characterization of a Heterometallic Extended Architecture Based on a Manganese(II)-Substituted Sandwich-Type Polyoxotungstate

PubMed Central

Ibrahim, Masooma; Moreno-Pineda, Eufemio; Anson, Christopher E.; Powell, Annie K.

2018-01-01

The reaction of [α-P2W15O56]12− with MnII and DyIII in an aqueous basic solution led to the isolation of an all inorganic heterometallic aggregate Na10(OH2)42[{Dy(H2O)6}2Mn4P4W30O112(H2O)2]·17H2O (Dy2Mn4-P2W15). Single-crystal X-ray diffraction revealed that Dy2Mn4-P2W15 crystallizes in the triclinic system with space group P1¯, and consists of a tetranuclear manganese(II)-substituted sandwich-type phosphotungstate [Mn4(H2O)2(P2W15O56)2]16− (Mn4-P2W15), Na, and DyIII cations. Compound Dy2Mn4-P2W15 exhibits a 1D ladder-like chain structure based on sandwich-type segments and dysprosium cations as linkers, which are further connected into a three-dimensional open framework by sodium cations. The title compound was structurally and compositionally characterized in solid state by single-crystal XRD, powder X-ray diffraction (PXRD), Fourier-transform infrared spectroscopy (FTIR), thermogravimetric (TGA), and elemental analyses. Further, the absorption and emission electronic spectra in aqueous solutions of Dy2Mn4-P2W15 and Mn4-P2W15 were studied. Also, magnetic properties were studied and compared with the magnetic behavior of [Mn4(H2O)2(P2W15O56)2]16−. PMID:29342122

Preparation of polycrystalline FeTe1- x S x ( x = 0.00-0.30) via solid-state reaction method at ambient pressure

NASA Astrophysics Data System (ADS)

Lim, Edmund H. H.; Liew, Josephine Y. C.; Awang Kechik, M. M.; Halim, S. A.; Chen, S. K.; Tan, K. B.; Qi, X.

2017-06-01

Polycrystalline samples with nominal composition FeTe1- x S x ( x = 0.00-0.30) were synthesized via solid state reaction method with intermittent grinding in argon gas flow. X-ray diffraction (XRD) patterns revealed the tetragonal structure (space group P4/nmm) of the samples with the presence of impurities Fe3O4 and FeTe2. By substitution with S, the a and c lattice parameters shrink probably due to the smaller ionic radius of S2- compared to Te2-. Scanning electron microscopy images showed that the samples developed plate-like grains with increasing S substitution. Substitution of Te with S suppresses the structural transition of the parent compound FeTe as shown by both the temperature dependence of resistance and magnetic moment measurements. All of the S-substituted samples showed a rapid drop of resistance at around 9-10 K but zero resistance down to 4 K was not observed. In addition, negative magnetic moment corresponds to diamagnetism was detected in the samples for x = 0.25 and 0.30 suggesting the coexistence of magnetic and superconducting phase in these samples. The magnetization hysteresis loops measured at room temperature showed ferromagnetic behavior for the pure and S substituted samples. However, the magnetization, rentivity and coercivity decreased with S content.

Structural, vibrational and luminescence properties of the (1−x)CaWO{sub 4}−xCdWO{sub 4} system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taoufyq, A.; Laboratoire Matériaux et Environnement LME, Faculté des Sciences, Université Ibn Zohr, BP 8106, Cité Dakhla, Agadir, Maroc; CEA/DEN, Département d’Études des Réacteurs, Laboratoire Dosimétrie Capteurs Instrumentation, CEA Cadarache, 13108, Saint-Paul-lez-Durance

2014-11-15

In the present work, we investigate the structural, microstructural, vibrational and luminescence properties of the system (1−x)CaWO{sub 4}−xCdWO{sub 4} with x ranging between 0 and 1. Polycrystalline samples were elaborated using a coprecipitation technique followed by thermal treatment at 1000 °C. The samples were then characterized using X-ray diffraction, scanning electron microscopy, Raman spectroscopy and luminescence analyses. X-ray diffraction profile analyses using Rietveld method showed that two kinds of solid solutions Ca{sub 1−x}Cd{sub x}WO{sub 4} having scheelite and wolframite structures, with respectively tetragonal and monoclinic crystal cells, were observed, with a biphasic system for compositions x=0.6 and 0.7. The scanningmore » electron microscopy experiments showed a complex evolution of morphologies and crystallite sizes as x increased. The vibration modes of Raman spectra were characteristic of composition-dependent disordered solid solutions with decreasing wavenumbers as x increased. Luminescence experiments were performed under UV-laser light irradiation. The energies of emission bands increased linearly with cadmium composition x. The integrated intensity of luminescence reached a maximum value for the substituted wolframite phase with composition x=0.8. - Graphical abstract: Luminescence on UV excitation (364.5 nm) of (1−x)CaWO{sub 4−x}CdWO{sub 4} system, elaborated from coprecipitation technique at 1000 °C, with 0« less

Hydrogen-deuterium substitution in solid ethanol by surface reactions at low temperatures

NASA Astrophysics Data System (ADS)

Oba, Yasuhiro; Osaka, Kazuya; Chigai, Takeshi; Kouchi, Akira; Watanabe, Naoki

2016-10-01

Ethanol (CH3CH2OH) is one of the most abundant complex organic molecules in star-forming regions. Despite its detection in the gas phase only, ethanol is believed to be formed by low-temperature grain-surface reactions. Methanol, the simplest alcohol, has been a target for observational, experimental, and theoretical studies in view of its deuterium enrichment in the interstellar medium; however, the deuterium chemistry of ethanol has not yet been an area of focus. Recently, deuterated dimethyl ether, a structural isomer of ethanol, was found in star-forming regions, indicating that deuterated ethanol can also be present in those environments. In this study, we performed laboratory experiments on the deuterium fractionation of solid ethanol at low temperatures through a reaction with deuterium (D) atoms at 10 K. Hydrogen (H)-D substitution, which increases the deuteration level, was found to occur on the ethyl group but not on the hydroxyl group. In addition, when deuterated ethanol (e.g. CD3CD2OD) solid was exposed to H atoms at 10 K, D-H substitution that reduced the deuteration level occurred on the ethyl group. Based on the results, it is likely that deuterated ethanol is present even under H-atom-dominant conditions in the interstellar medium.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Winstead, Cherese; Katagumpola, Pushpika

The degrees of substitution of chitosan derivatives were varied and the viscoelastic behavior of these biopolymer solutions was studied using rheology. Chitosan is a cationic copolymer of glucosamine and N-acetylglucosamine obtained by alkaline deacetylation of chitin. Due to its inherent non-toxicity, biocompatibility, and biodegradability, chitosan has gained much interest. However, the poor solubility of the biopolymer in water and most common organic solvents limits its applications. Therefore, the focus of this work is the chemical modification of chitosan via carboxymethylation as well as studying the viscoelastic behavior of these polymer solutions. Varying degrees of substitution (DS) of carboxymethyl chitosan derivativesmore » were synthesized by treating chitosan with monochloroacetic acid under alkylated medium varying the reaction time and temperature. The effect of degree of substitution on the rheology of these polymer solutions was studied as a function of concentration. The viscosity of chitosan derivatives sharply increased with increase in degree of substitution. G' and G' dependence on strain and angular frequency were studied and were found to exhibit predominantly viscous behavior. Additional characterization of the derivatized products were further studied using Fourier transform infrared (FT-IR), {sup 1}H Nuclear Magnetic Resonance ({sup 1}H NMR) spectroscopy, X-ray diffraction (XRD), and thermal gravimetric analysis as well as differential scanning calorimetry (DSC). Degree of substitution (DS) was calculated by titrimetric method.« less

Upgraded biogas from municipal solid waste for natural gas substitution and CO2 reduction--a case study of Austria, Italy, and Spain.

PubMed

Starr, Katherine; Villalba, Gara; Gabarrell, Xavier

2015-04-01

Biogas is rich in methane and can be further purified through biogas upgrading technologies, presenting a viable alternative to natural gas. Landfills and anaerobic digestors treating municipal solid waste are a large source of such biogas. They therefore offer an attractive opportunity to tap into this potential source of natural gas while at the same time minimizing the global warming impact resulting from methane emissions in waste management schemes (WMS) and fossil fuel consumption reduction. This study looks at the current municipal solid waste flows of Spain, Italy, and Austria over one year (2009), in order to determine how much biogas is generated. Then it examines how much natural gas could be substituted by using four different biogas upgrading technologies. Based on current waste generation rates, exploratory but realistic WMS were created for each country in order to maximize biogas production and potential for natural gas substitution. It was found that the potential substitution of natural gas by biogas resulting from the current WMS seems rather insignificant: 0.2% for Austria, 0.6% for Italy and 0.3% for Spain. However, if the WMS is redesigned to maximize biogas production, these figures can increase to 0.7% for Austria, 1% for Italy and 2% for Spain. Furthermore, the potential CO2 reduction as a consequence of capturing the biogas and replacing fossil fuel can result in up to a 93% reduction of the annual national waste greenhouse gas emissions of Spain and Italy. Copyright © 2015 Elsevier Ltd. All rights reserved.

In operando neutron diffraction study of LaNdMgNi9H13 as a metal hydride battery anode

NASA Astrophysics Data System (ADS)

Nazer, N. S.; Denys, R. V.; Yartys, V. A.; Hu, Wei-Kang; Latroche, M.; Cuevas, F.; Hauback, B. C.; Henry, P. F.; Arnberg, L.

2017-03-01

La2MgNi9-related alloys are superior metal hydride battery anodes as compared to the commercial AB5 alloys. Nd-substituted La2-yNdyMgNi9 intermetallics are of particular interest because of increased diffusion rate of hydrogen and thus improved performance at high discharge currents. The present work presents in operando characterization of the LaNdMgNi9 intermetallic as anode for the nickel metal hydride (Ni-MH) battery. We have studied the structural evolution of LaNdMgNi9 during its charge and discharge using in situ neutron powder diffraction. The work included experiments using deuterium gas and electrochemical charge-discharge measurements. The alloy exhibited a high electrochemical discharge capacity (373 mAh/g) which is 20% higher than the AB5 type alloys. A saturated β-deuteride synthesized by solid-gas reaction at PD2 = 1.6 MPa contained 12.9 deuterium atoms per formula unit (D/f.u.) which resulted in a volume expansion of 26.1%. During the electrochemical charging, the volume expansion (23.4%) and D-contents were found to be slightly reduced. The reversible electrochemical cycling is performed through the formation of a two-phase mixture of the α-solid solution and β-hydride phases. Nd substitution contributes to the high-rate dischargeability, while maintaining a good cyclic stability. Electrochemical Impedance Spectroscopy (EIS) was used to characterize the anode electrode on cycling. A mathematical model for the impedance response of a porous electrode was utilized. The EIS showed a decreased hydrogen transport rate during the long-term cycling, which indicated a corresponding slowing down of the electrochemical processes at the surface of the metal hydride anode.

Substituent effects on the electronic characteristics of pentacene derivatives for organic electronic devices: dioxolane-substituted pentacene derivatives with triisopropylsilylethynyl functional groups.

PubMed

Griffith, Olga Lobanova; Anthony, John E; Jones, Adolphus G; Shu, Ying; Lichtenberger, Dennis L

2012-08-29

The intramolecular electronic structures and intermolecular electronic interactions of 6,13-bis(triisopropylsilylethynyl)pentacene (TIPS pentacene), 6,14-bis-(triisopropylsilylethynyl)-1,3,9,11-tetraoxa-dicyclopenta[b,m]-pentacene (TP-5 pentacene), and 2,2,10,10-tetraethyl-6,14-bis-(triisopropylsilylethynyl)-1,3,9,11-tetraoxa-dicyclopenta[b,m]pentacene (EtTP-5 pentacene) have been investigated by the combination of gas-phase and solid-phase photoelectron spectroscopy measurements. Further insight has been provided by electrochemical measurements in solution, and the principles that emerge are supported by electronic structure calculations. The measurements show that the energies of electron transfer such as the reorganization energies, ionization energies, charge-injection barriers, polarization energies, and HOMO-LUMO energy gaps are strongly dependent on the particular functionalization of the pentacene core. The ionization energy trends as a function of the substitution observed for molecules in the gas phase are not reproduced in measurements of the molecules in the condensed phase due to polarization effects in the solid. The electronic behavior of these materials is impacted less by the direct substituent electronic effects on the individual molecules than by the indirect consequences of substituent effects on the intermolecular interactions. The ionization energies as a function of film thickness give information on the relative electrical conductivity of the films, and all three molecules show different material behavior. The stronger intermolecular interactions in TP-5 pentacene films lead to better charge transfer properties versus those in TIPS pentacene films, and EtTP-5 pentacene films have very weak intermolecular interactions and the poorest charge transfer properties of these molecules.

Stabilization of a supersaturated solution of mefenamic acid from a solid dispersion with EUDRAGIT(®) EPO.

PubMed

Kojima, Taro; Higashi, Kenjirou; Suzuki, Toyofumi; Tomono, Kazuo; Moribe, Kunikazu; Yamamoto, Keiji

2012-10-01

The stabilization mechanism of a supersaturated solution of mefenamic acid (MFA) from a solid dispersion with EUDRAGIT(®) EPO (EPO) was investigated. The solid dispersions were prepared by cryogenic grinding method. Powder X-ray diffractometry, in vitro dissolution test, in vivo oral absorption study, infrared spectroscopy, and solid- and solution-state NMR spectroscopies were used to characterize the solid dispersions. Dissolution tests in acetate buffer (pH 5.5) revealed that solid dispersion showed > 200-fold higher concentration of MFA. Supersaturated solution was stable over 1 month and exhibited improved oral bioavailability of MFA in rats, with a 7.8-fold higher area under the plasma concentration-versus-time curve. Solid-state (1)H spin-lattice relaxation time (T(1)) measurement showed that MFA was almost monomolecularly dispersed in the EPO polymer matrix. Intermolecular interaction between MFA and EPO was indicated by solid-state infrared and (13)C-T(1) measurements. Solution-state (1)H-NMR measurement demonstrated that MFA existed in monomolecular state in supersaturated solution. (1)H-T(1) and difference nuclear Overhauser effect measurements indicated that cross relaxation occurred between MFA and EPO due to the small distance between them. The formation and high stability of the supersaturated solution were attributable to the specifically formed intermolecular interactions between MFA and EPO.

Determination of oxygen vacancy limit in Mn substituted yttria stabilized zirconia

NASA Astrophysics Data System (ADS)

Stepień, Joanna; Sikora, Marcin; Kapusta, Czesław; Pomykalska, Daria; Bućko, Mirosław M.

2018-05-01

A series of Mnx(Y0.148Zr0.852)1-xO2-δ ceramics was systematically studied by means of X-ray absorption spectroscopy (XAS) and X-ray emission spectroscopy (XES) and DC magnetic susceptibility. The XAS and XES results show the changes in manganese oxidation state and a gradual evolution of the local atomic environment around Mn ions upon increasing dopant contents, which is due to structural relaxation caused by the growing amount of oxygen vacancies. Magnetic susceptibility measurements reveal that Mn3O4 precipitates are formed for x ≥ 0.1 and enable independent determination of the actual quantity of Mn ions dissolved in Yttria Stabilized Zirconia (YSZ) solid solution. We show that the amount of oxygen vacancies generated by manganese doping into YSZ is limited to ˜0.17 per formula unit.

Numerical solutions of incompressible Navier-Stokes equations using modified Bernoulli's law

NASA Astrophysics Data System (ADS)

Shatalov, A.; Hafez, M.

2003-11-01

Simulations of incompressible flows are important for many practical applications in aeronautics and beyond, particularly in the high Reynolds number regime. The present formulation is based on Helmholtz velocity decomposition where the velocity is presented as the gradient of a potential plus a rotational component. Substituting in the continuity equation yields a Poisson equation for the potential which is solved with a zero normal derivative at solid surfaces. The momentum equation is used to update the rotational component with no slip/no penetration surface boundary conditions. The pressure is related to the potential function through a special relation which is a generalization of Bernoulli's law, with a viscous term included. Results of calculations for two- and three-dimensional problems prove that the present formulation is a valid approach, with some possible benefits compared to existing methods.

Bismuth Sodium Titanate Based Materials for Piezoelectric Actuators

PubMed Central

Reichmann, Klaus; Feteira, Antonio; Li, Ming

2015-01-01

The ban of lead in many electronic products and the expectation that, sooner or later, this ban will include the currently exempt piezoelectric ceramics based on Lead-Zirconate-Titanate has motivated many research groups to look for lead-free substitutes. After a short overview on different classes of lead-free piezoelectric ceramics with large strain, this review will focus on Bismuth-Sodium-Titanate and its solid solutions. These compounds exhibit extraordinarily high strain, due to a field induced phase transition, which makes them attractive for actuator applications. The structural features of these materials and the origin of the field-induced strain will be revised. Technologies for texturing, which increases the useable strain, will be introduced. Finally, the features that are relevant for the application of these materials in a multilayer design will be summarized. PMID:28793724

Disposable cartridge extraction of retinol and alpha-tocopherol from fatty samples.

PubMed

Bourgeois, C F; Ciba, N

1988-01-01

A new approach is proposed for liquid/solid extraction of retinol and alpha-tocopherol from samples, using a disposable kieselguhr cartridge. The substitution of the mixture methanol-ethanol-n-butanol (4 + 3 + 1) for methanol in the alkaline hydrolysis solution makes it now possible to process fatty samples. Methanol is necessary to solubilize the antioxidant ascorbic acid, and a linear chain alcohol such as n-butanol is necessary to reduce the size of soap micelles so that they can penetrate into the kieselguhr pores. In comparisons of the proposed method with conventional methods on mineral premixes and fatty feedstuffs, recovery and accuracy are at least as good by the proposed method. Advantages are increased rate of determinations and the ability to hydrolyze and extract retinol and alpha-tocopherol together from the same sample.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Levin, I.; Laws, W. J.; Wang, D.

A crystal-chemical framework has been proposed for the design of pseudocubic perovskites with nanoscale ferroelectric order, and its applicability has been demonstrated using a series of representative solid solutions that combined ferroelectric (K0.5Bi0.5TiO3, BaTiO3, and PbTiO3) and antiferroelectric (Nd-substituted BiFeO3) end members. The pseudocubic structures obtained in these systems exhibited distortions that were coherent on a scale ranging from sub-nanometer to tens of nanometers, but, in all cases, the macroscopic distortion remained unresolvable even if using high-resolution X-ray powder diffraction. Different coherence lengths for the local atomic displacements account for the distinctly different dielectric, ferroelectric, and electromechanical properties exhibited bymore » the samples. The guidelines identified provide a rationale for chemically tuning the coherence length to obtain the desired functional response.« less

Multistimuli-responsive benzothiadiazole-cored phenylene vinylene derivative with nanoassembly properties.

PubMed

Dou, Chuandong; Chen, Dong; Iqbal, Javed; Yuan, Yang; Zhang, Hongyu; Wang, Yue

2011-05-17

A trifluoromethyl-substituted benzothiadiazole-cored phenylene vinylene fluorophore (1) was synthesized and displayed piezo- and vapochromism and thermo-induced fluorescence variation in solid phase. Grinding could disrupt the crystalline compound 1 with orange emission into amorphous compound 1 with green emission, and heating treatment could change the amorphous compound 1 into crystalline compound 1. Ultraviolet-visible (UV-vis) absorption spectra, (13)C nuclear magnetic resonance (NMR), and powder X-ray diffraction (PXRD) characterizations demonstrated that crystalline and amorphous compound 1 possess different molecular packing. A differential scanning calorimetry (DSC) measurement revealed that the emission switching was due to the exchange between the thermodynamic-stable crystalline and metastable amorphous states. The ground sample exhibited vapochromic fluorescence property. Furthermore, compound 1 showed interesting supramolecular assembly characteristics in solution. Slowly cooling the hot N,N-dimethylformamide (DMF) solution of compound 1 resulted in the formation of orange fluorescent fibers, whereas sonication treatment of the cooling solution led to the generation of organic molecular gel. The field emission scanning electronic microscope (FESEM) and fluorescent microscopy images revealed smooth nano- or microfiber and network morphology properties. The PXRD spectra confirmed that these nano- or microstructures had a similar molecular-packing model with the crystalline state of compound 1. Slow evaporation of the toluene solution of compound 1 could produce green emissive microrods, which exhibited interesting thermo-induced fluorescence variation.

From solid solution to cluster formation of Fe and Cr in α-Zr

NASA Astrophysics Data System (ADS)

Burr, P. A.; Wenman, M. R.; Gault, B.; Moody, M. P.; Ivermark, M.; Rushton, M. J. D.; Preuss, M.; Edwards, L.; Grimes, R. W.

2015-12-01

To understand the mechanisms by which the re-solution of Fe and Cr additions increase the corrosion rate of irradiated Zr alloys, the solubility and clustering of Fe and Cr in model binary Zr alloys was investigated using a combination of experimental and modelling techniques - atom probe tomography (APT), x-ray diffraction (XRD), thermoelectric power (TEP) and density functional theory (DFT). Cr occupies both interstitial and substitutional sites in the α-Zr lattice; Fe favours interstitial sites, and a low-symmetry site that was not previously modelled is found to be the most favourable for Fe. Lattice expansion as a function of Fe and Cr content in the α-Zr matrix deviates from Vegard's law and is strongly anisotropic for Fe additions, expanding the c-axis while contracting the a-axis. Matrix content of solutes cannot be reliably estimated from lattice parameter measurements, instead a combination of TEP and APT was employed. Defect clusters form at higher solution concentrations, which induce a smaller lattice strain compared to the dilute defects. In the presence of a Zr vacancy, all two-atom clusters are more soluble than individual point defects and as many as four Fe or three Cr atoms could be accommodated in a single Zr vacancy. The Zr vacancy is critical for the increased apparent solubility of defect clusters; the implications for irradiation induced microstructure changes in Zr alloys are discussed.

Single crystals of metal solid solutions

NASA Technical Reports Server (NTRS)

Miller, J. F.; Austin, A. E.; Richard, N.; Griesenauer, N. M.; Moak, D. P.; Mehrabian, M. R.; Gelles, S. H.

1974-01-01

The following definitions were sought in the research on single crystals of metal solid solutions: (1) the influence of convection and/or gravity present during crystallization on the substructure of a metal solid solution; (2) the influence of a magnetic field applied during crystallization on the substructure of a metal solid solution; and (3) requirements for a space flight experiment to verify the results. Growth conditions for the selected silver-zinc alloy system are described, along with pertinent technical and experimental details of the project.

Solid-state and solution /sup 13/C NMR in the conformational analysis of methadone-hydrochloride and related narcotic analgesics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sumner, S.C.J.

1986-01-01

Solid state and solution /sup 13/C NMR have been used to study the conformations of the racemic mixtures and single enantiomers of methadone hydrochloride, alpha and beta methadol hydrochloride, and alpha and beta acetylmethadol hydrochloride. The NMR spectra acquired for the compounds as solids, and in polar and nonpolar solvents are compared, in order to determine the conformation of the molecules in solution. To determine the reliability of assigning solution conformations by comparing solution and solid state chemical shift data, three bond coupling constants measured in solution are compared with those calculated from X-ray data. The conformations of the racemicmore » mixture and plus enantiomer of methadone hydrochloride have been shown to be very similar in the solid state, where minor differences in conformation can be seen by comparing NMR spectra obtained for the solids. Also shown is that the molecules of methadone hydrochloride have conformations in polar and in nonpolar solvents which are very similar to the conformation of the molecules in the solid state.« less

Vanadium-substituted heteropolyacids immobilized on amine- functionalized mesoporous MCM-41: A recyclable catalyst for selective oxidation of alcohols with H{sub 2}O{sub 2}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dong, Xinbo; Wang, Danjun; College of Chemistry Chemical Engineering, Yanan University, Shaanxi Key Laboratory of Chemical Reaction Engineering, Yan'an 716000

2014-09-15

Graphical abstract: Vanadium-substituted phosphotungstic acids are immobilized on amine- functionalized mesoporous MCM-41 and the hybrid catalyst is proved to be a highly efficient solid catalyst for the oxidation of aromatic alcohols to the corresponding carbonyl compounds with H{sub 2}O{sub 2}, featured by the high conversion and selectivity, easy recovery, and quite steady reuse. - Highlights: • Vanadium-substituted phosphotungstic acid immobilized on amine-functionalized mesoporous MCM-41 are prepared. • HPAs were fixed on the inner surface of mesoporous MCM-41 by chemical bonding to aminosilane groups. • The hybrid catalyst showed much higher catalytic activity than the pure HPAs. • The hybrid catalystmore » is a highly efficient recyclable solid catalyst for the selective oxidation of aromatic alcohols. - Abstract: New hybrid materials of vanadium-substituted phosphotungstic acids (VHPW) immobilized on amine-functionalized mesoporous MCM-41 (VHPW/MCM-41/NH{sub 2}) are prepared and characterized by FT-IR, XRD, N{sub 2} adsorption, elemental analysis, SEM and TEM for their structural integrity and physicochemical properties. It is found that the structure of the heteropolyacids is retained upon immobilization over mesoporous materials. The catalytic activities of these hybrid materials are tested in the selective oxidation of alcohols to the carbonyl products with 30% aqueous H{sub 2}O{sub 2} as oxidant in toluene. The catalytic activities of different number of vanadium-substituted phosphotungstic acid are investigated, and among the catalysts, H{sub 5}[PV{sub 2}W{sub 10}O{sub 40}] immobilized on amine-functionalized MCM-41 exhibits the highest activity with 97% conversion and 99% selectivity in the oxidation of benzyl alcohol to benzaldehyde. The hybrid catalyst is proved to be a highly efficient recyclable solid catalyst for the selective oxidation of aromatic alcohols to the corresponding aldehydes with H{sub 2}O{sub 2}.« less

Cationic Gold Clusters Ligated with Differently Substituted Phosphines: Effect of Substitution on Ligand Reactivity and Binding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, Grant E.; Olivares, Astrid M.; Hill, David E.

2015-01-01

We present a systematic study of the effect of the number of methyl (Me) and cyclohexyl (Cy) functional groups in monodentate phosphine ligands on the solution-phase synthesis of ligated sub-nanometer gold clusters and their gas-phase fragmentation pathways. Small mixed ligand cationic gold clusters were synthesized using ligand exchange reactions between pre-formed triphenylphosphine ligated (PPh3) gold clusters and monodentate Me- and Cy-substituted ligands in solution and characterized using electrospray ionization mass spectrometry (ESI-MS) and collision-induced dissociation (CID) experiments. Under the same experimental conditions, larger gold-PPh3 clusters undergo efficient exchange of unsubstituted PPh3 ligands for singly Me- and Cy-substituted PPh2Me and PPh2Cymore » ligands. The efficiency of ligand exchange decreases with an increasing number of Me or Cy groups in the substituted phosphine ligands. CID experiments performed for a series of ligand-exchanged gold clusters indicate that loss of a neutral Me-substituted ligand is preferred over loss of a neutral PPh¬3 ligand while the opposite trend is observed for Cy-substituted ligands. The branching ratio of the competing ligand loss channels is strongly correlated with the electron donating ability of the phosphorous lone pair as determined by the relative proton affinity of the ligand. The results indicate that the relative ligand binding energies increase in the order PMe3 < PPhMe2 < PPh2Me < PPh3< PPh2Cy < PPhCy2< PCy3. Furthermore, the difference in relative ligand binding energies increases with the number of substituted PPh3-mMem or PPh3-mCym ligands (L) exchanged onto each cluster. This study provides the first experimental determination of the relative binding energies of ligated gold clusters containing differently substituted monophosphine ligands, which are important to controlling their synthesis and reactivity in solution. The results also indicate that ligand substitution is an important parameter that must be considered in theoretical modeling of these complex systems« less

Light-induced noncentrosymmetry in acceptor-donor-substituted azobenzene solutions

NASA Astrophysics Data System (ADS)

Zhao, Jiang; Si, Jinhai; Wang, Yougui; Ye, Peixian; Fu, Xingfa; Qiu, Ling; Shen, Yuquan

1995-10-01

Light-induced noncentrosymmetry was achieved experimentally in acceptor-donor-substituted azobenzene solutions and observed by phase-matched nondegenerate six-wave mixing. The microscopic origin of the induced noncentrosymmetry was found to be orientational hole burning, which was distinguished directly with net orientation of molecules by experimental observations. The decay time of the induced noncentrosymmetry depended on the rotational orientation time of the sample's molecule, which varied linearly with the viscosity of the solvent.

Spectrophotometric determination of copper in alkaline solutions and evaluation of some hydroxy-substituted 1,10-phenanthrolines as chromogenic reagents.

PubMed

Dunbar, W E; Schilt, A A

1972-09-01

Seven new hydroxy-substituted 1,10-phenanthroline derivatives have been evaluated as chromogenic reagents for the determination of copper in strongly alkaline solution. The most sensitive of these, 2,9-dimethyl-4,7-dihydroxy-1,10-phenanthroline, has proven to be highly effective in a simple, rapid procedure for determining trace amounts of copper in sodium hydroxide, potassium carbonate, sodium phosphate or ammonium hydroxide.

Face-to-Face Packing of 2,3,9,10-Tetrasubstituted Pentacene Derivatives Revealed through a Solid State [4 + 4] Thermal Cycloaddition and Molecular Dynamic Simulation.

PubMed

Pal, Bikash; Lin, Bo-Chao; Dela Cerna, Mark Vincent Carreon; Hsu, Chao-Ping; Lin, Chih-Hsiu

2016-08-05

2,3,9,10-Substituted pentacene tetraesters and pentacene diester-dinitriles were synthesized. These pentacene derivatives underwent an unusual solid state [4 + 4] thermal dimerization with good efficiency and complete stereoselectivity. This observation indicates this series of pentacene derivatives adopt π-π stacking geometry with large mutual overlap in solid state. This notion was confirmed by molecualr dynamic simulation.

Thermodynamic Study of Solid-Liquid Equilibrium in NaCl-NaBr-H2O System at 288.15 K

NASA Astrophysics Data System (ADS)

Li, Dan; Meng, Ling-zong; Deng, Tian-long; Guo, Ya-fei; Fu, Qing-Tao

2018-06-01

The solubility data, composition of the solid solution and refractive indices of the NaCl-NaBr-H2O system at 288.15 K were studied with the isothermal equilibrium dissolution method. The solubility diagram and refractive index diagram of this system were plotted at 288.15 K. The solubility diagram consists of two crystallization zones for solid solution Na(Cl,Br) · 2H2O and Na(Cl,Br), one invariant points cosaturated with two solid solution and two univariant solubility isothermal curves. On the basis of Pitzer and Harvie-Weare (HW) chemical models, the composition equations and solubility equilibrium constant equations of the solid solutions at 288.15 K were acquired using the solubility data, the composition of solid solutions, and binary Pitzer parameters. The solubilities calculated using the new method combining the equations are in good agreement with the experimental data.

Effect of aging temperature on formation of sol-gel derived fluor-hydroxyapatite nanoparticles.

PubMed

Joughehdoust, S; Behnamghader, A; Jahandideh, R; Manafi, S

2010-04-01

Synthetic hydroxyapatite (HA) has been recognized as one of the most important bone substitute materials in orthopaedics and dentistry over past few decades because of its chemical and biological similarity to the mineral phase of human bone. One solution for reduction the solubility of HA in biological environments is replacing F- by OH in HA structure and forming fluor-hydroxyapatite (FHA) solid solution. In this paper, FHA nanoparticles were successfully synthesized by a sol-gel method. Also, the influence of aging temperature on formation of FHA powder was studied. Equimolar solutions of calcium nitrate tetrahydrate, triethyl phosphite and ammonium fluoride in ethanol were used as Ca, P and F precursors. After aging at different temperatures, the synthesized powders were heat treated at 550 degrees C. The powders were investigated with X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), transmission electron microscopy (TEM), selected area electron diffraction pattern (SAED), energy dispersive analysis of X-ray (EDAX) and zetasizer measurement. The results of XRD proved the presence of fluorapatite (FA) and HA in all samples. In addition, the formation of FHA was confirmed by FT-IR results. XRD studies also showed that the crystallites were in nanometric scale. At the same time, this result was in good agreement with the result of zetasizer analysis.

Synthesis of GaN:ZnO solid solution by solution combustion method and characterization for photocatalytic application

NASA Astrophysics Data System (ADS)

Menon, Sumithra Sivadas; Anitha, R.; Gupta, Bhavana; Baskar, K.; Singh, Shubra

2016-05-01

GaN-ZnO solid solution has emerged as a successful and reproducible photocatalyst for overall water splitting by one-step photoexcitation, with a bandgap in visible region. When the solid solution is formed, some of the Zn and O ions are replaced by Ga and N ions respectively and there is a narrowing of bandgap which is hypothesized as due to Zn3d-N2p repulsion. The traditional method of synthesis of GaN-ZnO solid solution is by nitridation of the starting oxides under constant ammonia flow. Here we report a solution combustion technique for the synthesis of the solid solution at a temperature about 500 ° C in a muffle furnace with metal nitrates as precursors and urea as the fuel. The as prepared samples showed change in color with the increased concentration of ZnO in the solution. The structural, microstructural, morphological and optical properties of the samples were realized by Powder X ray diffraction, Scanning electron microscopy, Energy dispersive X ray analysis, Transmission electron microscopy and Photoluminescence. Finally the hydrogen production efficiency of the GaN-ZnO nanopowders by water splitting was found, using methanol as a scavenger. The apparent quantum yield (AQY) of 0.048% is obtained for GaN-ZnO solid solution.

Ion mobility and conductivity in the M{sub 0.5–x}Pb{sub x}Bi{sub 0.5}F{sub 2+x} (M=K, Rb) solid solutions with fluorite structure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kavun, V. Ya., E-mail: kavun@ich.dvo.ru; Uvarov, N.F.; Slobodyuk, A.B.

Ionic mobility and conductivity in the K{sub 0.5–x}Pb{sub x}Bi{sub 0.5}F{sub 2+x} and Rb{sub 0.5–x}Pb{sub x}Bi{sub 0.5}F{sub 2+x} (x=0.05, 0.09) solid solutions with the fluorite structure have been investigated using the methods of {sup 19}F NMR, X-ray diffraction and impedance spectroscopy. Types of ionic motions in the fluoride sublattice of solid solutions have been established and temperature ranges of their realization have been determined (150–450 K). Diffusion of fluoride ions is a dominating type of ionic motions in the fluoride sublattice of solid solutions under study above 350 K. Due to high ionic conductivity, above 10{sup –3} S/cm at 450 K,more » these solid solutions can be used as solid electrolytes in various electrochemical devices and systems. - Graphical abstract: Temperature dependence of the concentration of mobile (2, 4) and immobile (1, 3) F ions in the K{sub 0.5–x}Pb{sub x}Bi{sub 0.5}F{sub 2+x} solid solutions. - Highlights: • Studied the ion mobility, conductivity in M{sub 0.5–x}Pb{sub x}Bi{sub 0.5}F{sub 2+x} solid solutions (M=K, Rb). • An analysis of {sup 19}F NMR spectra made it possible to identify types of ion mobility. • The main type of ion motion above 300 K in solid solutions is a diffusion of ions F{sup –}. • The ionic conductivity of the solid solutions studied more than 10{sup –3} S/cm at 450 K.« less

An added-mass partition algorithm for fluid–structure interactions of compressible fluids and nonlinear solids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Banks, J.W., E-mail: banksj3@rpi.edu; Henshaw, W.D., E-mail: henshw@rpi.edu; Kapila, A.K., E-mail: kapila@rpi.edu

We describe an added-mass partitioned (AMP) algorithm for solving fluid–structure interaction (FSI) problems involving inviscid compressible fluids interacting with nonlinear solids that undergo large rotations and displacements. The computational approach is a mixed Eulerian–Lagrangian scheme that makes use of deforming composite grids (DCG) to treat large changes in the geometry in an accurate, flexible, and robust manner. The current work extends the AMP algorithm developed in Banks et al. [1] for linearly elasticity to the case of nonlinear solids. To ensure stability for the case of light solids, the new AMP algorithm embeds an approximate solution of a nonlinear fluid–solidmore » Riemann (FSR) problem into the interface treatment. The solution to the FSR problem is derived and shown to be of a similar form to that derived for linear solids: the state on the interface being fundamentally an impedance-weighted average of the fluid and solid states. Numerical simulations demonstrate that the AMP algorithm is stable even for light solids when added-mass effects are large. The accuracy and stability of the AMP scheme is verified by comparison to an exact solution using the method of analytical solutions and to a semi-analytical solution that is obtained for a rotating solid disk immersed in a fluid. The scheme is applied to the simulation of a planar shock impacting a light elliptical-shaped solid, and comparisons are made between solutions of the FSI problem for a neo-Hookean solid, a linearly elastic solid, and a rigid solid. The ability of the approach to handle large deformations is demonstrated for a problem of a high-speed flow past a light, thin, and flexible solid beam.« less

Structural, dielectric and impedance characteristics of lanthanum-modified BiFeO3-PbTiO3 electronic system

NASA Astrophysics Data System (ADS)

Pradhan, S. K.; Das, S. N.; Bhuyan, S.; Behera, C.; Padhee, R.; Choudhary, R. N. P.

2016-06-01

A lanthanum-modified BiFeO3-PbTiO3 binary electronic system has been fabricated by a high-temperature solid-state reaction technique. The structural, dielectric and electrical properties of a single phase of multicomponent system are investigated to understand its ferroelectrics as well as relaxation behavior. The X-ray diffraction structural analysis substantiates the formation of a new stable phase of tetragonal system (with a large c/a ratio 1.23) without any trace of impurity phase. The electrical behavior of the processed material is characterized through impedance spectroscopy in a wide frequency range (1 kHz-1 MHz) over a temperature range of 25-500 °C. It is observed that the substitution of lanthanum-modified PbTiO3 (PT) into BiFeO3 (BFO) reveals enviable multiferroic property which is evident from the ME coefficient measurement and ferroelectric loop. It also reduces the electrical leakage current or tangent loss. The ac conductivity of the solid solution increases with increase in frequency in the low-temperature region. The impedance spectroscopy of the synthesized material reflects the dielectric relaxation of non-Debye type.

Establishing a molecular relationship between chondritic and cometary organic solids

PubMed Central

Cody, George D.; Heying, Emily; Alexander, Conel M. O.; Nittler, Larry R.; Kilcoyne, A. L. David; Sandford, Scott A.

2011-01-01

Multidimensional solid-state NMR spectroscopy is used to refine the identification and abundance determination of functional groups in insoluble organic matter (IOM) isolated from a carbonaceous chondrite (Murchison, CM2). It is shown that IOM is composed primarily of highly substituted single ring aromatics, substituted furan/pyran moieties, highly branched oxygenated aliphatics, and carbonyl groups. A pathway for producing an IOM-like molecular structure through formaldehyde polymerization is proposed and tested experimentally. Solid-state 13C NMR analysis of aqueously altered formaldehyde polymer reveals considerable similarity with chondritic IOM. Carbon X-ray absorption near edge structure spectroscopy of formaldehyde polymer reveals the presence of similar functional groups across certain Comet 81P/Wild 2 organic solids, interplanetary dust particles, and primitive IOM. Variation in functional group concentration amongst these extraterrestrial materials is understood to be a result of various degrees of processing in the parent bodies, in space, during atmospheric entry, etc. These results support the hypothesis that chondritic IOM and cometary refractory organic solids are related chemically and likely were derived from formaldehyde polymer. The fine-scale morphology of formaldehyde polymer produced in the experiment reveals abundant nanospherules that are similar in size and shape to organic nanoglobules that are ubiquitous in primitive chondrites. PMID:21464292

Solution combustion method for synthesis of nanostructured hydroxyapatite, fluorapatite and chlorapatite

NASA Astrophysics Data System (ADS)

Zhao, Junjie; Dong, Xiaochen; Bian, Mengmeng; Zhao, Junfeng; Zhang, Yao; Sun, Yue; Chen, JianHua; Wang, XuHong

2014-09-01

Hydroxyapatite (HAP), fluorapatite (Fap) and chlorapatite (Clap) were prepared by solution combustion method with further annealing at 800 °C. The characterization and structural features of the synthesized powders were evaluated by the powder X-ray diffraction (XRD, Fourier transform infrared spectroscopy (FT-IR), scanning electron microscope (SEM) and transmission electron microscopy (TEM) techniques. Characterization results from XRD and Rietveld analysis revealed that OH- in the HAP lattice were gradually substituted with the increase of F- and Cl- content and totally substituted at the molar concentration of 0.28 and 0.6, respectively. The results from FI-IR have also confirmed the incorporation of substituted anions in the apatite structure.

Investigation of compositional segregation during unidirectional solidification of solid solution semiconducting alloys

NASA Technical Reports Server (NTRS)

Wang, J. C.

1982-01-01

Compositional segregation of solid solution semiconducting alloys in the radial direction during unidirectional solidification was investigated by calculating the effect of a curved solid liquid interface on solute concentration at the interface on the solid. The formulation is similar to that given by Coriell, Boisvert, Rehm, and Sekerka except that a more realistic cylindrical coordinate system which is moving with the interface is used. Analytical results were obtained for very small and very large values of beta with beta = VR/D, where V is the velocity of solidification, R the radius of the specimen, and D the diffusivity of solute in the liquid. For both very small and very large beta, the solute concentration at the interface in the solid C(si) approaches C(o) (original solute concentration) i.e., the deviation is minimal. The maximum deviation of C(si) from C(o) occurs for some intermediate value of beta.

Process for recovering chaotropic anions from an aqueous solution also containing other ions

DOEpatents

Rogers, Robin; Horwitz, E. Philip; Bond, Andrew H.

1999-01-01

A solid/liquid process for the separation and recovery of chaotropic anions from an aqueous solution is disclosed. The solid support comprises separation particles having surface-bonded poly(ethylene glycol) groups, whereas the aqueous solution from which the chaotropic anions are separated contains a poly(ethylene glycol) liquid/liquid biphase-forming amount of a dissolved salt (lyotrope). A solid/liquid phase admixture of separation particles containing bound chaotropic anions in such an aqueous solution is also contemplated, as is a chromatography apparatus containing that solid/liquid phase admixture.

Process for recovering chaotropic anions from an aqueous solution also containing other ions

DOEpatents

Rogers, R.; Horwitz, E.P.; Bond, A.H.

1999-03-30

A solid/liquid process for the separation and recovery of chaotropic anions from an aqueous solution is disclosed. The solid support comprises separation particles having surface-bonded poly(ethylene glycol) groups, whereas the aqueous solution from which the chaotropic anions are separated contains a poly(ethylene glycol) liquid/liquid biphase-forming amount of a dissolved salt (lyotrope). A solid/liquid phase admixture of separation particles containing bound chaotropic anions in such an aqueous solution is also contemplated, as is a chromatography apparatus containing that solid/liquid phase admixture. 19 figs.

Role of lattice distortion on diffuse phase transition temperatures in Bi0.5Na0.5TiO3-BaTiO3 [BNBTO] solid solutions

NASA Astrophysics Data System (ADS)

Pradhan, Lagen Kumar; Pandey, Rabichandra; Kumar, Sunil; Supriya, Sweety; Kar, Manoranjan

2018-04-01

Effect of lattice distortion on diffuse phase transition in BNBTO solid solutions near Morphotropic phase boundary (MPB) has been investigated. Solid solutions of (Bi0.5Na0.5)1-xBaxTiO3 (with mole % of x= 0.04, 0.05, 0.06, 0.07 and 0.08) were prepared by the planetary ball mill method in ethanol medium. Rietveld refinement technique with rhombohedral (R3c) and tetragonal (P4bm) crystal symmetry has been employed for structural as well as phase analysis of the solid solutions. Both rhombohedral and tetragonal lattice distortion (c/a) tends toward the pseudo-cubic crystal symmetry with the increase of mole fraction of Ba2+ near MPB (x= 6 mole %). Also, the average crystallite size and grain size decrease with increase of mole fraction of Ba2+ in BNT ceramic are due to larger ionic radius of Ba2+ and grain boundary pinning process in the solid solutions respectively. Additionally, depolarization temperature (Td) and maximum temperature (Tm) reduces due to the lattice distortion of both the phases in BNBTO solid solutions, which is explained extensively. Significant increase of dielectric constant has been observed near MPB composition (x=6%) in BNBTO solid solutions.

Laboratory determination of the carbon kinetic isotope effects (KIEs) for reactions of methyl halides with various nucleophiles in solution

USGS Publications Warehouse

Baesman, S.M.; Miller, L.G.

2005-01-01

Large carbon kinetic isotope effects (KIEs) were measured for reactions of methyl bromide (MeBr), methyl chloride (MeCl), and methyl iodide (MeI) with various nucleophiles at 287 and 306 K in aqueous solutions. Rates of reaction of MeBr and MeI with H2O (neutral hydrolysis) or Cl- (halide substitution) were consistent with previous measurements. Hydrolysis rates increased with increasing temperature or pH (base hydrolysis). KIEs for hydrolysis were 51 ?? 6??? for MeBr and 38 ?? 8??? for MeI. Rates of halide substitution increased with increasing temperature and greater reactivity of the attacking nucleophile, with the fastest reaction being that of MeI with Br-. KIEs for halide substitution were independent of temperature but varied with the reactant methyl halide and the attacking nucleophile. KIEs were similar for MeBr substitution with Cl- and MeCl substitution with Br- (57 ?? 5 and 60 ?? 9??? respectively). The KIE for halide exchange of MeI was lower overall (33 ?? 8??? and was greater for substitution with Br- (46 ?? 6???) than with Cl- (29 ?? 6???). ?? Springer Science + Business Media, Inc. 2005.

Preparation of Sic/AIN Solid Solutions Using Organometallic Precursors

DTIC Science & Technology

1989-02-15

pyrolysis of organoaluminum and organosilicon compounds was investigated as a potential source of SiC /AUI solid solutions. Using two different co... pyrolysis methods, homogeneous mixtures of organoaluminum amides and both a vinylic polysilane and a poly- carbosilane were convertec to a preceramic ...solid that transformed to crystalline SiC /AiN solid solutions at 򒸀 C. Moreover, the liquid, polymeric , form of these precursor mixtures provides a

Local and average structure of Mn- and La-substituted BiFeO3

NASA Astrophysics Data System (ADS)

Jiang, Bo; Selbach, Sverre M.

2017-06-01

The local and average structure of solid solutions of the multiferroic perovskite BiFeO3 is investigated by synchrotron X-ray diffraction (XRD) and electron density functional theory (DFT) calculations. The average experimental structure is determined by Rietveld refinement and the local structure by total scattering data analyzed in real space with the pair distribution function (PDF) method. With equal concentrations of La on the Bi site or Mn on the Fe site, La causes larger structural distortions than Mn. Structural models based on DFT relaxed geometry give an improved fit to experimental PDFs compared to models constrained by the space group symmetry. Berry phase calculations predict a higher ferroelectric polarization than the experimental literature values, reflecting that structural disorder is not captured in either average structure space group models or DFT calculations with artificial long range order imposed by periodic boundary conditions. Only by including point defects in a supercell, here Bi vacancies, can DFT calculations reproduce the literature results on the structure and ferroelectric polarization of Mn-substituted BiFeO3. The combination of local and average structure sensitive experimental methods with DFT calculations is useful for illuminating the structure-property-composition relationships in complex functional oxides with local structural distortions.

Band gap and mobility of epitaxial perovskite BaSn1 -xHfxO3 thin films

NASA Astrophysics Data System (ADS)

Shin, Juyeon; Lim, Jinyoung; Ha, Taewoo; Kim, Young Mo; Park, Chulkwon; Yu, Jaejun; Kim, Jae Hoon; Char, Kookrin

2018-02-01

A wide band-gap perovskite oxide BaSn O3 is attracting much attention due to its high electron mobility and oxygen stability. On the other hand, BaHf O3 was recently reported to be an effective high-k gate oxide. Here, we investigate the band gap and mobility of solid solutions of BaS n1 -xH fxO3 (x =0 -1 ) (BSHO) as a basis to build advanced perovskite oxide heterostructures. All the films were epitaxially grown on MgO substrates using pulsed laser deposition. Density functional theory calculations confirmed that Hf substitution does not create midgap states while increasing the band gap. From x-ray diffraction and optical transmittance measurements, the lattice constants and the band-gap values are significantly modified by Hf substitution. We also measured the transport properties of n -type La-doped BSHO films [(Ba ,La ) (Sn ,Hf ) O3 ] , investigating the feasibility of modulation doping in the BaSn O3/BSHO heterostructures. The Hall measurement data revealed that, as the Hf content increases, the activation rate of the La dopant decreases and the scattering rate of the electrons sharply increases. These properties of BSHO films may be useful for applications in various heterostructures based on the BaSn O3 system.

The influence of aliovalent impurities on the oxidation kinetics of nickel at high temperatures

NASA Astrophysics Data System (ADS)

Mrowec, S.; Grzesik, Z.; Rajchel, B.; Gil, A.; Dabek, J.

2005-01-01

The influence of chromium and sodium on the nickel oxidation kinetics has been studied as a function of temperature (1373-1673 K) and oxygen activity (10-105 Pa O2), using microthermogravimetric techniques. It has been shown that the oxidation of Ni-Cr and Ni-Na alloys, like that of pure nickel, follows strictly the parabolic rate law being thus diffusion controlled. In agreement with the defect model of Ni1-yO, it has been found that the oxidation rate of the Ni-Cr alloy is higher than that of pure nickel, the reaction rate is pressure independent and the activation energy of this process is lower. This implies that the concentration of double ionized cation vacancies in a Ni1-yO-Cr2O3 solid solution is fixed on a constant level by trivalent chromium ions, substitutionally incorporated into the cation sublattice of this oxide. In the case of the Ni-Na alloy, on the other hand, the oxidation rate is lower than that of pure nickel, the activation energy is higher and the oxidation rate increases more rapidly with oxygen pressure. These results can again be explained in terms of the doping effect, by assuming that univalent sodium ions dissolve substitutionally in the cation sublattice of nickel oxide.

Local and average structure of Mn- and La-substituted BiFeO 3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiang, Bo; Selbach, Sverre M.

2017-06-01

The local and average structure of solid solutions of the multiferroic perovskite BiFeO 3 is investigated by synchrotron X-ray diffraction (XRD) and electron density functional theory (DFT) calculations. The average experimental structure is determined by Rietveld refinement and the local structure by total scattering data analyzed in real space with the pair distribution function (PDF) method. With equal concentrations of La on the Bi site or Mn on the Fe site, La causes larger structural distortions than Mn. Structural models based on DFT relaxed geometry give an improved fit to experimental PDFs compared to models constrained by the space groupmore » symmetry. Berry phase calculations predict a higher ferroelectric polarization than the experimental literature values, reflecting that structural disorder is not captured in either average structure space group models or DFT calculations with artificial long range order imposed by periodic boundary conditions. Only by including point defects in a supercell, here Bi vacancies, can DFT calculations reproduce the literature results on the structure and ferroelectric polarization of Mn-substituted BiFeO 3. The combination of local and average structure sensitive experimental methods with DFT calculations is useful for illuminating the structure-property-composition relationships in complex functional oxides with local structural distortions.« less

Characterization of Substituted Phenol-Formaldehyde Resins Using Solid-State Carbon-13 NMR

DTIC Science & Technology

1989-05-22

synthesized from cashew nut shell liquid, 3-n-pentadecylphenol and phenol with formaldehyde. The resulting resins were crosslinked and then investigated using...should be sent SYNOPSIS Crosslinked substituted phenol-formaldehyde resins were synthesized from cashew nut shell liquid, 3-n-pentadecylphenol and... nut shell liquid (CNSL) and are the basis for binder resins and friction particles in composite friction materials. CNSL is isolated from cashew nut

Processing waste fats into a fuel oil substitute

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pudel, F.; Lengenfeld, P.

1993-12-31

Waste fats have a high energy potential. They also contain impurities. For example, fats used for deep-frying contain high contents of solids, water, and chlorides. The process described in this paper removes the impurities by simple processing such as screening, washing, separating, drying, and filtering. The final quality of processed fat allows its use as a fuel oil substitute, and also as a raw material for chemical production.

FT-IR and FT-Raman spectra of 5-chlorocytosine: Solid state simulation and tautomerism. Effect of the chlorine substitution in the Watson-Crick base pair 5-chlorodeoxycytidine-deoxyguanosine

NASA Astrophysics Data System (ADS)

Alcolea Palafox, M.; Rastogi, V. K.; Singh, S. P.

2018-01-01

The laser Raman and IR spectra of 5-chlorocytosine have been recorded and accurately assigned in the solid state using Density functional calculations (DFT) together with the linear scaling equation procedure (LSE) and the solid state simulation of the crystal unit cell through a tetramer form. These results remarkably improve those reported previously by other authors. Several new scaling equations were proposed to be used in related molecules. The six main tautomers of the biomolecule 5-chlorocytosine were determined and optimized at the MP2 and CCSD levels, using different basis sets. The relative stabilities were compared with those obtained in cytosine and their 5-halo derivatives. Several relationships between energies, geometric parameters and NBO atomic charges were established. The effect of the chlorine substitution in the fifth position was evaluated through the stability of the Watson-Crick (WC) base pair of 5-chlorodeoxycytidine with deoxyguanosine, and through their vibrational spectra.

A Comprehensive Approach to Evaluating Hazards of Microplastics in the Marine Environment

NASA Astrophysics Data System (ADS)

Noble, A. E.; Lewis, A. S.; Butler, C. H.; Lunsman, T. D.; Verslycke, T.

2016-02-01

Plastic debris in the environment is a growing global concern, and the past decade has brought particular attention to a small size range of plastic debris, often referred to as microplastics. The potential environmental effects of microplastics are complex and, as yet, poorly understood. Emerging research suggests that specific plastic types pose environmental risks primarily via indirect toxicity caused by hazardous compounds associated with microplastics (e.g., monomers, additives, and sorbed environmental pollutants). However, our understanding of the physicochemical properties that determine the environmental fate and toxicity of microplastics is limited. Some recent regulatory initiatives have been broad, seeking to regulate all solid synthetic polymers ≤5 mm despite the lack of a sound technical basis for using solely a size-based cutoff. Such broad regulation of all solid synthetic polymers may actually discourage the use and innovation of less hazardous synthetic polymers and "greener" substitutes. We propose a polymer-specific approach to evaluating potential hazards of microplastics, informed by the state of the science and current research needs. This approach relies on identifying focused tests and analyses to set criteria for determining the degree to which a solid synthetic polymer is likely to pose environmental risk. Important considerations include degradation, sorptive capacity, and monomer/additive content. Our approach is a first step toward a more comprehensive way to evaluate the environmental hazards and risks of microplastics. Our goals are to develop clearer criteria to assess future solid synthetic polymers of unknown concern, inform microplastics regulation, and drive innovation of greener solutions to this global concern.

Electronic origin of strain effects on solute stabilities in iron

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Wei; Li, Xiangyan; Xu, Yichun, E-mail: xuyichun@issp.ac.cn, E-mail: csliu@issp.ac.cn

2016-08-21

Nonuniform strain fields might induce the segregation of alloying solutes and ultimately lead to the mechanical performance degradation of body-centered-cubic (bcc) Fe based steels serving in extreme environments, which is worthy of investigation. In this paper, two typical volume-conserving strains, shear strain (SS) and normal strain (NS), are proposed to investigate the strain effects on solute stabilities in bcc iron by first-principles calculations. For solutes in each transition metal group, the calculated substitution energy change due to SS exhibits a linear dependence on the valence d radius of the solutes, and the slope decreases in an exponential manner as amore » function of the absolute difference between the Watson's electronegativity of iron and the averaged value of each transition metal group. This regularity is attributed to the Pauli repulsion between the solutes and the nearest neighboring Fe ions modulated by the hybridization of valence d bands and concluded to be originated from the characteristics of valence d bonding between the transition-metal solutes and Fe ions under SS. For main-group and post transition-metal solutes, the considerable drop of substitution energy change due to NS is concluded to be originated from the low-energy side shift of the widened valence s and p bands of the solutes. Our results indicate that the stabilities of substitutional solutes in iron under volume-conserving strain directly correlate with the intrinsic properties of the alloying elements, such as the valence d radius and occupancy, having or not having valence s and p bands.« less

Back to the kitchen: food-grade agar is a low-cost alternative to bacteriological agar.

PubMed

Petrovski, Steve; Tillett, Daniel

2012-10-15

Food-grade agar can be used as a low-cost substitute for bacteriological agar in the preparation of solid microbial media. No difference was observed in the colony morphology, growth rate, or viability of bacteria grown on solid media prepared using food-grade agar as compared with using bacteriological-grade agar. This simple tip can reduce the cost of the most common solid media by 80% or more. Copyright © 2012 Elsevier Inc. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rai, R.N., E-mail: rn_rai@yahoo.co.in; Kant, Shiva; Reddi, R.S.B.

Urea is an attractive material for frequency conversion of high power lasers to UV (for wavelength down to 190 nm), but its usage is hindered due to its hygroscopic nature, though there is no alternative organic NLO crystal which could be transparent up to 190 nm. The hygroscopic character of urea has been modified by making the solid solution (UCNB) of urea (U) and p-chloronitrobenzene (CNB). The formation of the solid solution of CNB in U is explained on the basis of phase diagram, powder XRD, FTIR, elemental analysis and single crystal XRD studies. The solubility of U, CNB andmore » UCNB in ethanol solution is evaluated at different temperatures. Transparent single crystals of UCNB are grown from its saturated solution in ethanol. Optical properties e.g., second harmonic generation (SHG), refractive index and the band gap for UCNB crystal were measured and their values were compared with the parent compounds. Besides modification in hygroscopic nature, UCNB has also shown the higher SHG signal and mechanical hardness in comparison to urea crystal. - Highlights: • The hygroscopic character of urea was modified by making the solid solution • Solid solution formation is support by elemental, powder- and single crystal XRD • Crystal of solid solution has higher SHG signal and mechanical stability. • Refractive index and band gap of solid solution crystal have determined.« less

Effect of carbon and alloying solute atoms on helium behaviors in α-Fe

NASA Astrophysics Data System (ADS)

Zhang, Yange; You, Yu-Wei; Xu, Yichun; Liu, C. S.; Chen, J. L.; Luo, G.-N.

2017-02-01

Helium bubbles could strongly degrade the mechanical properties of ferritic steels in fission and fusion systems. The formation of helium bubble is directly affected by the interactions between helium and the compositions in steels, such as solute atoms, carbon and irradiation defects. We thereby performed systematical first-principles calculations to investigate the interactions of solute-helium and carbon-solute-helium. It is found that substitutional helium is more attractive than interstitial helium to all the considered 3p, 4p, 5p and 6p solutes. The attraction between carbon and substitutional helium suggests the carbon-solute-helium complex can be formed stably. By examining the charge density difference and thermal stability, it is found that the ternary complex shows stronger attraction with He than that of solute-helium pair for some solutes (S, Se, In, Te, Pb and Bi) and the complex could existed in iron stably at 700 K. The present theoretical results may be helpful for exploring alloy additions to mitigate the formation of large helium bubbles.

Chemical composition and varieties of fahlore-group minerals from Oligocene mineralization in the Rhodope area, Southern Bulgaria and Northern Greece

NASA Astrophysics Data System (ADS)

Repstock, Alexander; Voudouris, Panagiotis; Zeug, Manuela; Melfos, Vasilios; Zhai, Mingguo; Li, Hongzhong; Kartal, Tamara; Matuszczak, Julia

2016-02-01

Fahlore-group minerals in Oligocene magmatic-hydrothermal deposits from the central and eastern Rhodope area, Bulgaria and Greece (e.g. porphyry-epithermal systems at Pagoni Rachi, Maronia and Kassiteres-Sapes, polymetallic epithermal high- and intermediate-sulfidation veins at Kirki, Perama Hill, Mavrokoryfi, Pefka, Zvezdel-Pcheloyad and Madzharovo, skarn-carbonate replacement deposits at Laki, Davidkovo, Madan, Enyovche and intrusion-related deposits at Kimmeria), cover the whole range of the tetrahedrite-tennantite solid solution series and are dominated by zincian and ferroan varieties reflecting deposition from Zn-(and Fe)-rich fluids. The majority of the studied fahlores are "normal" fully-substituted with Cu (+Ag) close to 10 apfu. However, high-sulfidation epithermal deposits in Greece contain "Cu-excess" tetrahedrite-tennantite; those with extreme high Cu-excess > Fe + Zn occur in transitional high- to intermediate-sulfidation systems, whereas low "Cu-excess" tetrahedrite-tennantite with Zn > Cu-excess + Fe and Fe > Cu-excess + Zn are part of tellurides-bearing intermediate-sulfidation assemblages. The epithermal St. Demetrios and Pefka deposits display the most Cu-rich tetrahedrites (11.039 apfu Cu) and tennantite (11.784 apfu Cu) worldwide. Although Ag substitutes for Cu in the structure of Ag-rich tetrahedrite in several deposits, freibergite with 6.800 apfu Ag occurs only at Mavrokoryfi; in particular, the cadmian freibergite at Mavrokoryfi is the second finding of this variety worldwide. Tellurium-bearing fahlore varieties occur in association with enargite/luzonite and native gold in high-sulfidation ore assemblages. Tetravalent tellurium substitutes for trivalent As and Sb in goldfieldite and Te-rich tennantite and tetrahedrite at Mavrokoryfi, Perama Hill, St. Demetrios and Pefka deposits. Goldfieldite at Mavrokoryfi and Perama Hill is remarkably Te-rich (up to 3.766 apfu and 3.711 apfu Te, respectively), with total metal content of 10.591 apfu and are the closest natural occurrence to the theoretical synthetic endmember Cu10Te4S13. The telluride-bearing fahlores in several epithermal deposits in Greece do not represent decomposition products of early goldfieldite. They are possibly the result of a new influx of Te-rich magmatic volatiles in the system. Decreasing Te (and Cu)-content in tetrahedrite-tennantite solid solution series reflects an evolution from initial high-T, high-sulfidation, oxidizing conditions, towards lower-T and lower-sulfidation, more reduced conditions with time. Fahlores, although they are minor constituents in the studied mineralization types, are carriers of Ag (and Au in goldfieldite) and may be used as an exploration tool, since they are closely associated with either native gold, gold-silver tellurides or Ag-sulfosalts.

Stability of solid oxide fuel cell materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Armstrong, T.R.; Bates, J.L.; Chick, L.A.

1996-04-01

Interconnection materials in a solid oxide fuel cell are exposed to both highly oxidizing conditions at the cathode and to highly reducing conditions at the anode. The thermal expansion characteristics of substituted lanthanum and yttrium chromite interconnect materials were evaluated by dilatometry as a function of oxygen partial pressures from 1 atm to 10{sup -18} atm, controlled using a carbon dioxide/hydrogen buffer.

Dissolution of aragonite-strontianite solid solutions in nonstoichiometric Sr (HCO3)2-Ca (HCO3)2-CO2-H2O solutions

USGS Publications Warehouse

Plummer, Niel; Busenberg, E.; Glynn, P.D.; Blum, A.E.

1992-01-01

Synthetic strontianite-aragonite solid-solution minerals were dissolved in CO2-saturated non-stoichiometric solutions of Sr(HCO3)2 and Ca(HCO3)2 at 25??C. The results show that none of the dissolution reactions reach thermodynamic equilibrium. Congruent dissolution in Ca(HCO3)2 solutions either attains or closely approaches stoichiometric saturation with respect to the dissolving solid. In Sr(HCO3)2 solutions the reactions usually become incongruent, precipitating a Sr-rich phase before reaching stoichiometric saturation. Dissolution of mechanical mixtures of solids approaches stoichiometric saturation with respect to the least stable solid in the mixture. Surface uptake from subsaturated bulk solutions was observed in the initial minutes of dissolution. This surficial phase is 0-10 atomic layers thick in Sr(HCO3)2 solutions and 0-4 layers thick in Ca(HCO3)2 solutions, and subsequently dissolves and/or recrystallizes, usually within 6 min of reaction. The initial transient surface precipitation (recrystallization) process is followed by congruent dissolution of the original solid which proceeds to stoichiometric saturation, or until the precipitation of a more stable Sr-rich solid. The compositions of secondary precipitates do not correspond to thermodynamic equilibrium or stoichiometric saturation states. X-ray photoelectron spectroscopy (XPS) measurements indicate the formation of solid solutions on surfaces of aragonite and strontianite single crystals immersed in Sr(HCO3)2 and Ca(HCO3)2 solutions, respectively. In Sr(HCO3)2 solutions, the XPS signal from the outer ~ 60 A?? on aragonite indicates a composition of 16 mol% SrCO3 after only 2 min of contact, and 14-18 mol% SrCO3 after 3 weeks of contact. The strontianite surface averages approximately 22 mol% CaCO3 after 2 min of contact with Ca(HCO3)2 solution, and is 34-39 mol% CaCO3 after 3 weeks of contact. XPS analysis suggests the surface composition is zoned with somewhat greater enrichment in the outer ~25 A?? (as much as 26 mol% SrCO3 on aragonite and 44 mol% CaCO3 on strontianite). The results indicate rapid formation of a solid-solution surface phase from subsaturated aqueous solutions. The surface phase continually adjusts in composition in response to changes in composition of the bulk fluid as net dissolution proceeds. Dissolution rates of the endmembers are greatly reduced in nonstoichiometric solutions relative to dissolution rates observed in stoichiometric solutions. All solids dissolve more slowly in solutions spiked with the least soluble component ((Sr(HCO3)2)) than in solutions spiked with the more soluble component (Ca(HCO3)2), an effect that becomes increasingly significant as stoichiometric saturation is approached. It is proposed that the formation of a non-stoichiometric surface reactive zone significantly decreases dissolution rates. ?? 1992.

Precipitation in Al–Mg solid solution prepared by solidification under high pressure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jie, J.C., E-mail: jiejc@dlut.edu.cn; School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001; Wang, H.W.

2014-01-15

The precipitation in Al–Mg solid solution containing 21.6 at.% Mg prepared by solidification under 2 GPa was investigated. The results show that the γ-Al{sub 12}Mg{sub 17} phase is formed and the β′ phase cannot be observed in the solid solution during ageing process. The precipitation of γ and β phases takes place in a non-uniform manner during heating process, i.e. the γ and β phases are first formed in the interdendritic region, which is caused by the inhomogeneous distribution of Mg atoms in the solid solution solidified under high pressure. Peak splitting of X-ray diffraction patterns of Al(Mg) solid solutionmore » appears, and then disappears when the samples are aged at 423 K for different times, due to the non-uniform precipitation in Al–Mg solid solution. The direct transformation from the γ to β phase is observed after ageing at 423 K for 24 h. It is considered that the β phase is formed through a peritectoid reaction of α + γ → β which needs the diffusion of Mg atoms across the interface of α/γ phases. - Highlights: • The γ phase is formed and the β′ phase is be observed in Al(Mg) solid solution. • Peak splitting of XRD pattern of Al(Mg) solid solution appears during aged at 150 °C. • The β phase is formed through a peritectoid reaction of α + γ → β.« less

POSS-Based Electrolyte for Efficient Solid-State Dye-Sensitized Solar Cells at Sub-Zero Temperatures.

PubMed

Lv, Kai; Zhang, Wei; Zhang, Lu; Wang, Zhong-Sheng

2016-03-02

To expand the application of solid-state dye-sensitized solar cells (ssDSSCs) to low temperatures, it is necessary to develop new solid electrolytes with low glass transition temperature (Tg). The Tg is regulated by varying the length of alkyl chain that is connected with the nitrogen atom in the imidazolium ring linked to the polyhedral oligomeric silsesquioxane (POSS). The Tg as low as -8.8 °C is achieved with the POSS grafted with methyl-substituted imidazolium. The effect of alkyl group on the conductivity, Tg, and photovoltaic performance has also been investigated. The conductivity and power conversion efficiency increase with the alkyl length, while the Tg first increases and then decreases with the alkyl length. Among the synthesized POSS-based ionic conductors, the POSS grafted with the methyl-substituted imidazolium yields the highest power conversion efficiency of 6.98% at RT due to its highest conductivity, and the efficiency (6.52%) is still good at -4 °C, as its Tg (-8.8 °C) is lower than the working temperature (-4 °C). This finding suggests that the POSS-based solid electrolyte is promising for subzero-temperature applications of ssDSSCs.

Enhanced photocatalytic degradation of 2-propanol over macroporous GaN/ZnO solid solution prepared by a novel sol-gel method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Lizhong; Ouyang, Shuxin; Ren, Bofan

2015-10-01

Macroporous GaN/ZnO solid solution photocatalyst is synthesized through a novel sol-gel method under mild conditions. The performance of as-synthesized solid solution photocatalyst is evaluated for decomposition of gaseous 2-propanol (IPA). It is found that due to enhancement in both the adsorption to gaseous IPA and the absorbance to visible light, the porous GaN/ZnO solid solution exhibits a good photocatalytic performance for IPA decomposition. Moreover, the mechanism for photocatalytic degradation IPA over porous GaN/ZnO solid solution is also investigated in comparison with those for the two end materials ZnO and GaN. The trapping effects with different scavengers prove that both themore » photoexcited electrons and holes affect the IPA photodegradation process, simultaneously.« less

Synthesis of GaN:ZnO solid solution by solution combustion method and characterization for photocatalytic application

DOE Office of Scientific and Technical Information (OSTI.GOV)

Menon, Sumithra Sivadas; Anitha, R.; Baskar, K.

2016-05-23

GaN-ZnO solid solution has emerged as a successful and reproducible photocatalyst for overall water splitting by one-step photoexcitation, with a bandgap in visible region. When the solid solution is formed, some of the Zn and O ions are replaced by Ga and N ions respectively and there is a narrowing of bandgap which is hypothesized as due to Zn3d-N2p repulsion. The traditional method of synthesis of GaN-ZnO solid solution is by nitridation of the starting oxides under constant ammonia flow. Here we report a solution combustion technique for the synthesis of the solid solution at a temperature about 500 °more » C in a muffle furnace with metal nitrates as precursors and urea as the fuel. The as prepared samples showed change in color with the increased concentration of ZnO in the solution. The structural, microstructural, morphological and optical properties of the samples were realized by Powder X ray diffraction, Scanning electron microscopy, Energy dispersive X ray analysis, Transmission electron microscopy and Photoluminescence. Finally the hydrogen production efficiency of the GaN-ZnO nanopowders by water splitting was found, using methanol as a scavenger. The apparent quantum yield (AQY) of 0.048% is obtained for GaN-ZnO solid solution.« less

Mechanical behavior of regular open-cell porous biomaterials made of diamond lattice unit cells.

PubMed

Ahmadi, S M; Campoli, G; Amin Yavari, S; Sajadi, B; Wauthle, R; Schrooten, J; Weinans, H; Zadpoor, A A

2014-06-01

Cellular structures with highly controlled micro-architectures are promising materials for orthopedic applications that require bone-substituting biomaterials or implants. The availability of additive manufacturing techniques has enabled manufacturing of biomaterials made of one or multiple types of unit cells. The diamond lattice unit cell is one of the relatively new types of unit cells that are used in manufacturing of regular porous biomaterials. As opposed to many other types of unit cells, there is currently no analytical solution that could be used for prediction of the mechanical properties of cellular structures made of the diamond lattice unit cells. In this paper, we present new analytical solutions and closed-form relationships for predicting the elastic modulus, Poisson׳s ratio, critical buckling load, and yield (plateau) stress of cellular structures made of the diamond lattice unit cell. The mechanical properties predicted using the analytical solutions are compared with those obtained using finite element models. A number of solid and porous titanium (Ti6Al4V) specimens were manufactured using selective laser melting. A series of experiments were then performed to determine the mechanical properties of the matrix material and cellular structures. The experimentally measured mechanical properties were compared with those obtained using analytical solutions and finite element (FE) models. It has been shown that, for small apparent density values, the mechanical properties obtained using analytical and numerical solutions are in agreement with each other and with experimental observations. The properties estimated using an analytical solution based on the Euler-Bernoulli theory markedly deviated from experimental results for large apparent density values. The mechanical properties estimated using FE models and another analytical solution based on the Timoshenko beam theory better matched the experimental observations. Copyright © 2014 Elsevier Ltd. All rights reserved.

Carbonate substitution in lead hydroxyapatite Pb5(PO4)3OH

NASA Astrophysics Data System (ADS)

Kwaśniak-Kominek, M.; Manecki, M.; Matusik, J.; Lempart, M.

2017-11-01

Synthetic carbonate lead hydroxyapatite Pb5(PO4,CO3)3(OH,CO3) was precipitated from aqueous solution and characterized. The maximum content of CO32- ion in lead apatites does not exceed 2.25 wt%. For precipitation from aqueous solutions this is even lower and controlled by the solubility of cerussite PbCO3. Carbonate substitution occurs simultaneously in two structural positions: at OH- sites (A-type substitution) and at PO43- sites (B-type substitution). This is the most pronounced in FTIR (Fourier Transform Infrared Spectroscopy) spectra at 865 cm-1 and within the range of 1300-1500 cm-1. The substitution results in slight increase of the unit cell parameter a from 9.874 to 9.904 A. The presence of CO32- in two structural positions results in two stages of the release of CO2 upon heating: at 300-350 °C and at 400 °C. The presence of carbonates has little effect on thermal decomposition of lead hydroxyapatite which starts at about 450 °C resulting in the formation of lead pyrophosphate.

Blood substitutes.

PubMed Central

Kostrzewska, E.

1976-01-01

With the development of modern methods of surgery, anaesthesia, and pre- and postoperative care the requirement for blood substitutes is continuously increasing. We present a review of the different blood substitutes which are already in clinical use or in an advanced stage of experimental investigation for possible practical administration. Our own clinical experience with dextrans and experimental studies on stroma-free haemoglobin and hydroxyethyl starch solutions are described. PMID:57736

Exploring hardness enhancement in superhard tungsten tetraboride-based solid solutions using radial X-ray diffraction

DOE PAGES

Xie, Miao; Mohammadi, Reza; Turner, Christopher L.; ...

2015-07-29

In this paper, we explore the hardening mechanisms in WB4-based solid solutions upon addition of Ta, Mn, and Cr using in situ radial X-ray diffraction techniques under nonhydrostatic pressure. By examining the lattice-supported differential strain, we provide insights into the mechanism for hardness increase in binary solid solutions at low dopant concentrations. Speculations on the combined effects of electronic structure and atomic size in ternary WB 4 solid solutions containing Ta with Mn or Cr are also included to understand the extremely high hardness of these materials.

Ion mobility and transport properties of bismuth fluoride-containing solid solutions with tysonite-type structure

NASA Astrophysics Data System (ADS)

Kavun, V. Ya.; Uvarov, N. F.; Slobodyuk, A. B.; Merkulov, E. B.; Polyantsev, M. M.

2018-07-01

The ion mobility and conductivity of solid solutions with tysonite-type structure obtained by doping bismuth trifluoride with lead (II) fluoride, and zirconium and bismuth oxides have been studied using 19F NMR, X-ray diffraction analysis, and impedance spectroscopy. The types of ionic motions in the fluoride sublattice of the synthesized solid solutions in the temperature range 150-450 K have been determined and the energy of their activation has been estimated. Due to high ionic conductivity, above 10-2 S/cm at 570 K, these solid solutions can be considered as superionic conductors.

Solid-solution CrCoCuFeNi high-entropy alloy thin films synthesized by sputter deposition

DOE PAGES

An, Zhinan; Jia, Haoling; Wu, Yueying; ...

2015-05-04

The concept of high configurational entropy requires that the high-entropy alloys (HEAs) yield single-phase solid solutions. However, phase separations are quite common in bulk HEAs. A five-element alloy, CrCoCuFeNi, was deposited via radio frequency magnetron sputtering and confirmed to be a single-phase solid solution through the high-energy synchrotron X-ray diffraction, energy-dispersive spectroscopy, wavelength-dispersive spectroscopy, and transmission electron microscopy. The formation of the solid-solution phase is presumed to be due to the high cooling rate of the sputter-deposition process.

Fluorescence spectroscopy and amplified spontaneous emission (ASE) of phenylimidazoles: predicted vibronic coupling along the excited-state intramolecular proton transfer in 2-(2'-hydroxyphenyl)imidazoles.

PubMed

del Valle, Juan Carlos; Claramunt, R M; Catalán, J

2008-06-26

Methylation at the 1N position of 2-phenylimidazole provides the shortest wavelength for a liquid-state laser dye reported to date; that is, the 1-methyl-2-phenylimidazole molecule in cyclohexane solution yields amplified spontaneous emission (ASE) with a peak wavelength at 314.5 nm and a constant laser gain value of 5 cm(-1) from 310 to 317 nm. Methyl substitution in this case favors the appearance of laser action (owing to a torsion-vibrational mechanism) in cyclohexane as compared with the nonmethylated species which does not exhibit ASE in this solvent. The 2-(2'-hydroxyphenyl)imidazole molecules give rise to ASE with high gain values (ca. 9 cm(-1)) at 450 and 466 nm. The mechanism of population inversion is understood in terms of a vibronic coupling between the hydroxyl stretching motion and the torsional vibration of the phenyl and imidazole rings. The proton-transfer spectroscopy of 2-(2'-hydroxyphenyl)imidazoles is studied in dioxane, cyclohexane, dimethyl sulfoxide, methanol, and water. The greater the acidity of the solvent the greater the disruption of the intramolecular hydrogen bond; solvent acidity is the main parameter which favors formation of the open-form species in the ground electronic state. Methyl substitution at the 1N position favors formation of the open species for 2-hydroxyphenylimidazoles in the ground electronic state, which decreases their own capacity to undergo ASE. Low-temperature absorption spectroscopy confirms aggregation processes for 2-(2'-hydroxyphenyl)imidazoles in solution. In accordance with X-ray analyses in the solid phase, these molecules form associations through intermolecular chains of the type N-H...O or O-H...N.

Development and validation of a matrix solid-phase dispersion method to determine acrylamide in coffee and coffee substitutes.

PubMed

Soares, Cristina M Dias; Alves, Rita C; Casal, Susana; Oliveira, M Beatriz P P; Fernandes, José Oliveira

2010-04-01

The present study describes the development and validation of a new method based on a matrix solid-phase dispersion (MSPD) sample preparation procedure followed by GC-MS for determination of acrylamide levels in coffee (ground coffee and brewed coffee) and coffee substitute samples. Samples were dispersed in C(18) sorbent and the mixture was further packed into a preconditioned custom-made ISOLUTE bilayered SPE column (C(18)/Multimode; 1 g + 1 g). Acrylamide was subsequently eluted with water, and then derivatized with bromine and quantified by GC-MS in SIM mode. The MSPD/GC-MS method presented a LOD of 5 microg/kg and a LOQ of 10 microg/kg. Intra and interday precisions ranged from 2% to 4% and 4% to 10%, respectively. To evaluate the performance of the method, 11 samples of ground and brewed coffee and coffee substitutes were simultaneously analyzed by the developed method and also by a previously validated method based in a liquid-extraction (LE) procedure, and the results were compared showing a high correlation between them.

Hydrothermal synthesis and characterization of Si and Sr co-substituted hydroxyapatite nanowires using strontium containing calcium silicate as precursors.

PubMed

Zhang, Na; Zhai, Dong; Chen, Lei; Zou, Zhaoyong; Lin, Kaili; Chang, Jiang

2014-04-01

In the absence of any organic surfactants and solvents, the silicon (Si) and strontium (Sr) co-substituted hydroxyapatite [Ca10(PO4)6(OH)2, Si/Sr-HAp] nanowires were synthesized via hydrothermal treatment of the Sr-containing calcium silicate (Sr-CS) powders as the precursors in trisodium phosphate (Na3PO4) aqueous solution. The morphology, phase, chemical compositions, lattice constants and the degradability of the products were characterized. The Si/Sr-HAp nanowires with diameter of about 60nm and up to 2μm in length were obtained after hydrothermal treatment of the Sr-CS precursors. The Sr and Si substitution amount of the HAp nanowires could be well regulated by facile tailoring the Sr substitution level of the precursors and the reaction ratio of the precursor/solution, respectively. The SiO4 tetrahedra and Sr(2+) ions occupied the crystal sites of the HAp, and the lattice constants increased apparently with the increase of the substitution amount. EDS mapping also suggested the uniform distribution of Si and Sr in the synthetic nanowires. Moreover, the Si/Sr-substitution apparently improved the degradability of the HAp materials. Our study suggested that the precursor transformation method provided a facile approach to synthesize the Si/Sr co-substituted HAp nanowires with controllable substitution amount, and the synthetic Si/Sr-HAp nanowires might be used as bioactive materials for hard tissue regeneration applications. Copyright © 2014 Elsevier B.V. All rights reserved.

Modelling solid solutions with cluster expansion, special quasirandom structures, and thermodynamic approaches

NASA Astrophysics Data System (ADS)

Saltas, V.; Horlait, D.; Sgourou, E. N.; Vallianatos, F.; Chroneos, A.

2017-12-01

Modelling solid solutions is fundamental in understanding the properties of numerous materials which are important for a range of applications in various fields including nanoelectronics and energy materials such as fuel cells, nuclear materials, and batteries, as the systematic understanding throughout the composition range of solid solutions for a range of conditions can be challenging from an experimental viewpoint. The main motivation of this review is to contribute to the discussion in the community of the applicability of methods that constitute the investigation of solid solutions computationally tractable. This is important as computational modelling is required to calculate numerous defect properties and to act synergistically with experiment to understand these materials. This review will examine in detail two examples: silicon germanium alloys and MAX phase solid solutions. Silicon germanium alloys are technologically important in nanoelectronic devices and are also relevant considering the recent advances in ternary and quaternary groups IV and III-V semiconductor alloys. MAX phase solid solutions display a palette of ceramic and metallic properties and it is anticipated that via their tuning they can have applications ranging from nuclear to aerospace industries as well as being precursors for particular MXenes. In the final part, a brief summary assesses the limitations and possibilities of the methodologies discussed, whereas there is discussion on the future directions and examples of solid solution systems that should prove fruitful to consider.

Structural characterisation of the Li argyrodites Li7PS6 and Li7PSe6 and their solid solutions: quantification of site preferences by MAS-NMR spectroscopy.

PubMed

Kong, Shiao Tong; Gün, Ozgül; Koch, Barbara; Deiseroth, Hans Jörg; Eckert, Hellmut; Reiner, Christof

2010-05-03

Li(7)PS(6) and Li(7)PSe(6) belong to a class of new solids that exhibit high Li(+) mobility. A series of quaternary solid solutions Li(7)PS(6-x)Se(x) (0 < or = x < or = 6) were characterised by X-ray crystallography and magic-angle spinning nuclear magnetic resonance (MAS-NMR) spectroscopy. The high-temperature (HT) modifications were studied by single-crystal investigations (both F43m, Z=4, Li(7)PS(6): a=9.993(1) A, Li(7)PSe(6): a=10.475(1) A) and show the typical argyrodite structures with strongly disordered Li atoms. HT-Li(7)PS(6) and HT-Li(7)PSe(6) transform reversibly into low-temperature (LT) modifications with ordered Li atoms. X-ray powder diagrams show the structures of LT-Li(7)PS(6) and LT-Li(7)PSe(6) to be closely related to orthorhombic LT-alpha-Cu(7)PSe(6). Single crystals of the LT modifications are not available due to multiple twinning and formation of antiphase domains. The gradual substitution of S by Se shows characteristic site preferences closely connected to the functionalities of the different types of chalcogen atoms (S, Se). High-resolution solid-state (31)P NMR is a powerful method to differentiate quantitatively between the distinct (PS(4-n)Se(n))(3-) local environments. Their population distribution differs significantly from a statistical scenario, revealing a pronounced preference for P-S over P-Se bonding. This preference, shown for the series of LT samples, can be quantified in terms of an equilibrium constant specifying the melt reaction Se(P)+S(2-) <==>S(P)+Se(2-), prior to crystallisation. The (77)Se MAS-NMR spectra reveal that the chalcogen distributions in the second and third coordination sphere of the P atoms are essentially statistical. The number of crystallographically independent Li atoms in both LT modifications was analysed by means of (6)Li{(7)Li} cross polarisation magic angle spinning (CPMAS).

Quench-age method for the fabrication of niobium-aluminum superconductors

DOEpatents

Pickus, Milton R.; Ciardella, Robert L.

1978-01-01

A flexible Nb.sub.3 Al superconducting wire is fabricated from a niobium-aluminum composite wire by heating to form a solid solution which is retained at room temperature as a metastable solid solution by quenching. The metastable solid solution is then transformed to the stable superconducting A-15 phase by low temperature aging. The transformation induced by aging can be controlled to yield either a multifilamentary or a solid A-15 core surrounded by ductile niobium.

Self-assembled squares and triangles by simultaneous hydrogen bonding and metal coordination.

PubMed

Marshall, Laura J; de Mendoza, Javier

2013-04-05

Through the combination of hydrogen bonding and metal-templated self-assembly, molecular squares and molecular triangles are observed in chloroform solution upon the complexation of hydrogen-bonded dimers of para-pyridyl-substituted 2-ureido-4-[1H]-pyrimidinone (UPy) and an appropriate cis-substituted palladium complex. Molecular modeling studies and NMR analysis confirmed the presence of two distinct structures in solution: the tubular structure of the molecular square and propeller-bowl structure of the molecular triangle.

Polymeric medium

DOEpatents

Klaehn, John R [Idaho Falls, ID; Peterson, Eric S [Idaho Falls, ID; Orme, Christopher J [Shelley, ID; Jones, Michael G [Chubbuck, ID; Wertsching, Alan K [Idaho Falls, ID; Luther, Thomas A [Idaho Falls, ID; Trowbridge, Tammy L [Idaho Falls, ID

2012-03-06

A PBI compound includes imidazole nitrogens at least a portion of which are substituted with a moiety containing a carbonyl group, the substituted imidazole nitrogens being bonded to carbon of the carbonyl group. At least 85% of the nitrogens may be substituted. The carbonyl-containing moiety may include RCO--, where R is alkoxy or haloalkyl. The PBI compound may exhibit a first temperature marking an onset of weight loss corresponding to reversion of the substituted PBI that is less than a second temperature marking an onset of decomposition of an otherwise identical PBI compound without the substituted moiety. The PBI compound may be included in separatory media. A substituted PBI synthesis method may include providing a parent PBI in a less than 5 wt % solvent solution. Substituting may use more than 5 equivalents in relation to the imidazole nitrogens to be substituted.

Polybenzimidazole compounds

DOEpatents

Klaehn, John R [Idaho Falls, ID; Peterson, Eric S [Idaho Falls, ID; Orme, Christopher J [Shelley, ID; Jones, Michael G [Chubbuck, ID; Wertsching, Alan K [Idaho Falls, ID; Luther, Thomas A [Idaho Falls, ID; Trowbridge, Tammy L [Idaho Falls, ID

2011-11-22

A PBI compound includes imidazole nitrogens at least a portion of which are substituted with a moiety containing a carbonyl group, the substituted imidazole nitrogens being bonded to carbon of the carbonyl group. At least 85% of the nitrogens may be substituted. The carbonyl-containing moiety may include RCO--, where R is alkoxy or haloalkyl. The PBI compound may exhibit a first temperature marking an onset of weight loss corresponding to reversion of the substituted PBI that is less than a second temperature marking an onset of decomposition of an otherwise identical PBI compound without the substituted moiety. The PBI compound may be included in separatory media. A substituted PBI synthesis method may include providing a parent PBI in a less than 5 wt % solvent solution. Substituting may use more than 5 equivalents in relation to the imidazole nitrogens to be substituted.

Transition from itinerant metamagnetism to ferromagnetism in UCo1-xOsxAl solid solutions

NASA Astrophysics Data System (ADS)

Andreev, A. V.; Šebek, J.; Shirasaki, K.; Daniš, S.; Gorbunov, D. I.; Yamamura, T.; Vejpravová, J.; Havela, L.; de Boer, F. R.

2018-05-01

The influence of substitution of a small amount of Os (<2%) on the Co sublattice on the magnetism of the itinerant metamagnet UCoAl is studied on single-crystalline UCo1-xOsxAl compounds with x = 0.002, 0.005 and 0.01. For x = 0.002, the ground state is still paramagnetic, like in UCoAl. The metamagnetic-transition field is 0.37 T, twice lower than in UCoAl. The compound with x = 0.005 is at the border between the paramagnetic and the ferromagnetic ground state. At T = 2 K, it is ferromagnetic, at elevated temperatures a magnetic field is necessary to maintain the magnetic state. In zero field, the ferromagnetic state vanishes at T = 8 K. The compound with x = 0.01 is a ferromagnet with strong uniaxial magnetic anisotropy similar to the previously studied compounds with x = 0.02-0.20.

Synthesis and high proton conductive performance of a quaternary vanadomolybdotungstosilicic heteropoly acid.

PubMed

Cai, Huaxue; Wu, Xuefei; Wu, Qingyin; Yan, Wenfu

2016-09-28

A new vanadium and molybdenum-substituted quaternary silicon-containing heteropoly acid H6SiW9MoV2O40·15H2O has been synthesized in this paper by the stepwise acidification and the stepwise addition of elemental solutions. The structural feature and hydration of this product were characterized by IR, UV, XRD and TG-DTA, and its proton conductivity was measured by electrochemical impedance spectroscopy (EIS). The result of EIS shows that H6SiW9MoV2O40·15H2O is a solid high-proton conductor with a conductivity of 6.01 × 10(-3) S cm(-1) at 22 °C and 80% relative humidity, which increases at higher temperatures. Its conductive activation energy is 27.5 kJ mol(-1), which suggests that the mechanism of proton conduction is dominated by the vehicle mechanism.

Suppression of the cooperative Jahn-Teller distortion and its effect on the Raman octahedra-rotation modes of TbM n1 -xF exO3

NASA Astrophysics Data System (ADS)

Vilarinho, R.; Passos, D. J.; Queirós, E. C.; Tavares, P. B.; Almeida, A.; Weber, M. C.; Guennou, M.; Kreisel, J.; Moreira, J. Agostinho

2018-04-01

This work reports the changes in structure and lattice dynamics induced by substituting the Jahn-Teller-active M n3 + ion by the Jahn-Teller-inactive F e3 + in TbM n1 -xF exO3 over the full composition range. The structural analysis reveals that the amplitude of the cooperative Jahn-Teller distortion decreases linearly from x =0 (pure TbMn O3 ) to x =0.5 , where it is completely suppressed. We then correlate this evolution with the behavior of the Raman modes across the solid solution. In particular, we show that the Raman modes associated with the rotation of octahedra, whose wave number is commonly considered to scale linearly with the tilt angles in orthorhombic Pnma perovskites, are also sensitive to the amplitude of the Jahn-Teller distortion.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Costa, R. C. da; Universidade Federal de Campina Grande, Pombal-PB, 58840-000; Toledo, T. A. de

The effects of the atomic substitution of Pb by Ni in the PbTiO{sub 3} ferroelectric perovskite on the vibrational and structural properties was studied using x-ray diffraction and Raman scattering. It was observed that for Ni concentrations between 0.0 and 0.4, there is the formation of a solid solution with reduction of the Raman wavenumber of the E(TO1) soft mode and the tetragonallity factor, which influence directly the temperature of the tetragonal ferroelectric to cubic paraelectric phase transition, the Curie temperature. For concentrations greater than 0.4, it is observed the formation of a PbTiO{sub 3} and NiTiO{sub 3} composite, denouncedmore » by the recovering of the both, tetragonallity factor and the E(TO1) soft mode wavenumber. The values of the Curie temperatures were estimated by the Raman scattering measurements for temperatures ranging from 300 to 950 K.« less

Interstitial atoms enable joint twinning and transformation induced plasticity in strong and ductile high-entropy alloys.

PubMed

Li, Zhiming; Tasan, Cemal Cem; Springer, Hauke; Gault, Baptiste; Raabe, Dierk

2017-01-12

High-entropy alloys (HEAs) consisting of multiple principle elements provide an avenue for realizing exceptional mechanical, physical and chemical properties. We report a novel strategy for designing a new class of HEAs incorporating the additional interstitial element carbon. This results in joint activation of twinning- and transformation-induced plasticity (TWIP and TRIP) by tuning the matrix phase's instability in a metastable TRIP-assisted dual-phase HEA. Besides TWIP and TRIP, such alloys benefit from massive substitutional and interstitial solid solution strengthening as well as from the composite effect associated with its dual-phase structure. Nanosize particle formation and grain size reduction are also utilized. The new interstitial TWIP-TRIP-HEA thus unifies all metallic strengthening mechanisms in one material, leading to twice the tensile strength compared to a single-phase HEA with similar composition, yet, at identical ductility.

Large thermal conductivity reduction induced by La/O vacancies in the thermoelectric LaCoO3 system.

PubMed

Wang, Yang; Li, Fang; Xu, Luxiang; Sui, Yu; Wang, Xianjie; Su, Wenhui; Liu, Xiaoyang

2011-05-16

A series of compact La/O-vacant La(1-x)CoO(3-y) compounds were prepared by a cold high-pressure procedure, and their thermoelectric (TE) properties were investigated. Compared with the ion-substituted hole-type LaCoO(3) systems (e.g., La(1-x)Sr(x)CoO(3)), the thermal conduction of La(1-x)CoO(3-y) is noticeably reduced by the La/O vacancies, whereas the electric transport is less influenced, which results in an efficient ZT enhancement. We demonstrate that the large thermal conductivity reduction originates from the strong point-defect scattering, and La(1-x)CoO(3-y) can be rationalized as a partially filled solid solution: La(1-x)◻(x)CoO(3-y)◻(y), where ◻ denotes a vacancy. Such intrinsic thermal conductivity suppression provides an effective pathway for the design of better TE materials.

Formation of Multi-Layer Structures in Bi3Pb7 Intermetallic Compounds under an Ultra-High Gravitational Field

NASA Astrophysics Data System (ADS)

Mashimo, T.; Iguchi, Y.; Bagum, R.; Sano, T.; Sakata, O.; Ono, M.; Okayasu, S.

2008-02-01

Ultra-high gravitational field (Mega-gravity field) can promote sedimentation of atoms (diffusion) even in solids, and is expected to form a compositionally-graded structure and/or nonequilibrium phase in multi-component condensed matter. We had achieved sedimentation of substitutional solute atoms in miscible systems (Bi-Sb, In-Pb, etc.). In this study, a mega-gravity experiment at high temperature was performed on a thin-plate sample (0.7 mm in thickness) of the intermetallic compound Bi3Pb7. A visible four-layer structure was produced, which exhibited different microscopic structures. In the lowest-gravity region layer, Bi phase appeared. In the mid layers, a compositionally-graded structure was formed, with differences observed in the powder X-ray diffraction patterns. Such a multi-layer structure is expected to exhibit unique physical properties such as superconductivity.

Mechanical properties of particulate composites based on a body-centered-cubic Mg-Li alloy containing boron

NASA Technical Reports Server (NTRS)

Whalen, R. T.; Gonzalez-Doncel, G.; Robinson, S. L.; Sherby, O. D.

1989-01-01

The effect of substituting the Mg metal in Mg-B composites by a Mg-14 wt pct Li solid solution on the ductility of the resulting composite was investigated using elastic modulus measurements on the P/M composite material prepared with a dispersion of B particles (in a vol pct range of 0-30) in a matrix of Mg-14 wt pct Li-1.5 wt pct Al. It was found that the elastic modulus of the composites increased rapidly with increasing boron, with specific stiffness values reaching about two times that of most structural materials. The values of the compression and tensile strengths increased significantly with boron additions. Good tensile ductility was achieved at the level of 10 vol pct B. However, at 20 vol pct B, the Mg-Li composite exhibited only limited tensile ductility (about 2 percent total elongation).

Interstitial atoms enable joint twinning and transformation induced plasticity in strong and ductile high-entropy alloys

NASA Astrophysics Data System (ADS)

Li, Zhiming; Tasan, Cemal Cem; Springer, Hauke; Gault, Baptiste; Raabe, Dierk

2017-01-01

High-entropy alloys (HEAs) consisting of multiple principle elements provide an avenue for realizing exceptional mechanical, physical and chemical properties. We report a novel strategy for designing a new class of HEAs incorporating the additional interstitial element carbon. This results in joint activation of twinning- and transformation-induced plasticity (TWIP and TRIP) by tuning the matrix phase’s instability in a metastable TRIP-assisted dual-phase HEA. Besides TWIP and TRIP, such alloys benefit from massive substitutional and interstitial solid solution strengthening as well as from the composite effect associated with its dual-phase structure. Nanosize particle formation and grain size reduction are also utilized. The new interstitial TWIP-TRIP-HEA thus unifies all metallic strengthening mechanisms in one material, leading to twice the tensile strength compared to a single-phase HEA with similar composition, yet, at identical ductility.

Towards eco-friendly crop protection: natural deep eutectic solvents and defensive secondary metabolites.

PubMed

Mouden, Sanae; Klinkhamer, Peter G L; Choi, Young Hae; Leiss, Kirsten A

2017-01-01

With mounting concerns over health and environmental effects of pesticides, the search for environmentally acceptable substitutes has amplified. Plant secondary metabolites appear in the horizon as an attractive solution for green crop protection. This paper reviews the need for changes in the techniques and compounds that, until recently, have been the mainstay for dealing with pest insects. Here we describe and discuss main strategies for selecting plant-derived metabolites as candidates for sustainable agriculture. The second part surveys ten important insecticidal compounds, with special emphasis on those involved in human health. Many of these insecticidal metabolites, however, are crystalline solids with limited solubility which might potentially hamper commercial formulation. As such, we introduce the concept of natural deep eutectic solvents for enhancing solubility and stability of such compounds. The concept, principles and examples of green pest control discussed here offer a new suite of environmental-friendly tools designed to promote and adopt sustainable agriculture.

Correlation of Solid State and Solution Coordination Numbers with Infrared Spectroscopy in Five-, Six-, and Eight-Coordinate Transition Metal Complexes of DOTAM.

PubMed

Nagata, Maika K C T; Brauchle, Paul S; Wang, Sen; Briggs, Sarah K; Hong, Young Soo; Laorenza, Daniel W; Lee, Andrea G; Westmoreland, T David

2016-08-16

Three new DOTAM (1,4,7,10-tetrakis(acetamido)-1,4,7,10-tetraazacyclododecane) complexes have been synthesized and characterized by X-ray crystallography: [Co(DOTAM)]Cl 2 •3H 2 O, [Ni(DOTAM)]Cl 2 •4H 2 O, and [Cu(DOTAM)](ClO 4 ) 2 •H 2 O. Solid state and solution IR spectroscopic features for a series of [M(DOTAM)] 2+ complexes (M=Mn, Co, Cu, Ni, Ca, Zn) correlate with solid state and solution coordination numbers. [Co(DOTAM)] 2+ , [Ni(DOTAM)] 2+ , and [Zn(DOTAM)] 2+ are demonstrated to be six-coordinate in both the solid state and in solution, while [Mn(DOTAM)] 2+ and [Ca(DOTAM)] 2+ are eight-coordinate in the solid state and remain so in solution. [Cu(DOTAM)] 2+ , which is five-coordinate by X-ray crystallography, is shown to increase its coordination number in solution to six-coordinate.

Modeling of the phase evolution in Mg1-xAlxB2 (0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andersson, Anders David; Casillas, Luis; Lezama Pacheco, Juan

Despite the chemical and structural simplicity of MgB{sub 2}, at 39 K this compound has the highest known {Tc} of any binary compound. Electron doping by substituting Al for Mg leads to decreasing Tc and the observed concentration dependent rate of decrease has been proposed to arise from the non-ideal character of MgB{sub 2}-AIB{sub 2} solid solutions, which derives from the existence of an ordered Mg{sub 0.5}Al{sub 0.5}B{sub 2} compound. Heterogeneous nano-scale structure patterns in solid solutions have emerged as an important concept for complex materials, ranging from actinide alloys and oxides to high-temperature cuprate superconductors and mallganite-based materials exhibitingmore » colossal magnetoresistivity. In this work we investigate the formation of structural heterogeneities in Mg{sub 1-x}AI{sub x}B{sub 2}, which take the form of nano-scale AI-AI and AI-Mg domains of different geometry and size, using molecular statics/dynamics simulations and in particular we study the corresponding signatures in diffraction experiments. In order to undertake this task we first derive appropriate Mg-AI-B semi-empirical potentials within the Modified Embedded Atom Method formalism. These potentials are also applied to explore the equilibrium Mg{sub 1-x}AI{sub x}B{sub 2} phase diagram for 0 < x < 0.5. Additionally, density functional theory calculations were utilized to study the influence of heterogeneities on the electronic structure and charge distribution in Mg{sub 1-x}AI{sub x}B{sub 2}.« less

Mineralogical and chemical characteristics of some natural jarosites

USGS Publications Warehouse

Desborough, G.A.; Smith, K.S.; Lowers, H.A.; Swayze, G.A.; Hammarstrom, J.M.; Diehl, S.F.; Leinz, R.W.; Driscoll, R.L.

2010-01-01

This paper presents a detailed study of the mineralogical, microscopic, thermal, and spectral characteristics of jarosite and natrojarosite minerals. Systematic mineralogic and chemical examination of a suite of 32 natural stoichiometric jarosite and natrojarosite samples from diverse supergene and hydrothermal environments indicates that there is only limited solid solution between Na and K at low temperatures, which suggests the presence of a solvus in the jarosite-natrojarosite system at temperatures below about 140 ??C. The samples examined in this study consist of either end members or coexisting end-member pairs of jarosite and natrojarosite. Quantitative electron-probe microanalysis data for several natural hydrothermal samples show only end-member compositions for individual grains or zones, and no detectable alkali-site deficiencies, which indicates that there is no hydronium substitution within the analytical uncertainty of the method. In addition, there is no evidence of Fe deficiencies in the natural hydrothermal samples. Hydronium-bearing jarosite was detected in only one relatively young supergene sample suggesting that terrestrial hydronium-bearing jarosites generally are unstable over geologic timescales. Unit-cell parameters of the 20 natural stoichiometric jarosites and 12 natural stoichiometric natrojarosites examined in this study have distinct and narrow ranges in the a- and c-cell dimensions. There is no overlap of these parameters at the 1?? level for the two end-member compositions. Several hydrothermal samples consist of fine-scale (2-10 ??m) intimate intergrowths of jarosite and natrojarosite, which could have resulted from solid-state diffusion segregation or growth zoning due to variations in the Na/K activity ratio of hydrothermal solutions.

Solid/liquid interfacial free energies in binary systems

NASA Technical Reports Server (NTRS)

Nason, D.; Tiller, W. A.

1973-01-01

Description of a semiquantitative technique for predicting the segregation characteristics of smooth interfaces between binary solid and liquid solutions in terms of readily available thermodynamic parameters of the bulk solutions. A lattice-liquid interfacial model and a pair-bonded regular solution model are employed in the treatment with an accommodation for liquid interfacial entropy. The method is used to calculate the interfacial segregation and the free energy of segregation for solid-liquid interfaces between binary solutions for the (111) boundary of fcc crystals. The zone of compositional transition across the interface is shown to be on the order of a few atomic layers in width, being moderately narrower for ideal solutions. The free energy of the segregated interface depends primarily upon the solid composition and the heats of fusion of the component atoms, the composition difference of the solutions, and the difference of the heats of mixing of the solutions.

77 FR 16679 - Emergency Planning and Notification; Emergency Planning and List of Extremely Hazardous...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-22

...The U.S. Environmental Protection Agency (EPA or the Agency) is taking final action to revise the manner for applying the threshold planning quantities (TPQs) for those extremely hazardous substances (EHSs) that are non-reactive solid chemicals in solution. This revision allows facilities subject to the Emergency Planning requirements that have a non-reactive solid EHS in solution, to first multiply the amount of the solid chemical in solution on-site by 0.2 before determining if this quantity equals or exceeds the lower published TPQ. This change is based on data that shows less potential for non-reactive solid chemicals in solution to remain airborne and dispersed beyond a facility's fence line in the event of an accidental release. Previously, EPA assumed that 100% of non-reactive solid chemicals in solution could become airborne and dispersed beyond the fenceline in the event of an accidental release.

Fluorine-doped antiperovskite electrolyte for all-solid-state Lithium-ion batteries

DOE PAGES

Li, Yutao; Zhou, Weidong; Xin, Sen; ...

2016-06-30

A fluorine-doped antiperovskite Li-ion conducto Li 2(OH)X (X=Cl, Br) is shown to be a promising candidat for a solid electrolyte in an all-solid-state Li-ion rechargeabl battery. Substitution of F¯ for OH¯ transforms orthorhombi Li 2OHCl to a room-temperature cubic phase, which show electrochemical stability to 9 V versus Li +/Li and two orders o magnitude higher Li-ion conductivity than that of orthorhombi Li 2OHCl. As a result, an all-solid-state Li/LiFePO 4 with F-dope Li 2OHCl as the solid electrolyte showed good cyclability an a high coulombic efficiency over 40 charge/discharge cycles

System and process for dissolution of solids

DOEpatents

Liezers, Martin; Farmer, III, Orville T.

2017-10-10

A system and process are disclosed for dissolution of solids and "difficult-to-dissolve" solids. A solid sample may be ablated in an ablation device to generate nanoscale particles. Nanoparticles may then swept into a coupled plasma device operating at atmospheric pressure where the solid nanoparticles are atomized. The plasma exhaust may be delivered directly into an aqueous fluid to form a solution containing the atomized and dissolved solids. The composition of the resulting solution reflects the composition of the original solid sample.

COMPUTATIONAL ELECTROCHEMISTRY: AQUEOUS ONE-ELECTRON OXIDATION POTENTIALS FOR SUBSTITUTED ANILINES

EPA Science Inventory

Semiempirical molecular orbital theory and density functional theory are used to compute one-electron oxidation potentials for aniline and a set of 21 mono- and di-substituted anilines in aqueous solution. Linear relationships between theoretical predictions and experiment are co...

Analytical solution for the transient wave propagation of a buried cylindrical P-wave line source in a semi-infinite elastic medium with a fluid surface layer

NASA Astrophysics Data System (ADS)

Shan, Zhendong; Ling, Daosheng

2018-02-01

This article develops an analytical solution for the transient wave propagation of a cylindrical P-wave line source in a semi-infinite elastic solid with a fluid layer. The analytical solution is presented in a simple closed form in which each term represents a transient physical wave. The Scholte equation is derived, through which the Scholte wave velocity can be determined. The Scholte wave is the wave that propagates along the interface between the fluid and solid. To develop the analytical solution, the wave fields in the fluid and solid are defined, their analytical solutions in the Laplace domain are derived using the boundary and interface conditions, and the solutions are then decomposed into series form according to the power series expansion method. Each item of the series solution has a clear physical meaning and represents a transient wave path. Finally, by applying Cagniard's method and the convolution theorem, the analytical solutions are transformed into the time domain. Numerical examples are provided to illustrate some interesting features in the fluid layer, the interface and the semi-infinite solid. When the P-wave velocity in the fluid is higher than that in the solid, two head waves in the solid, one head wave in the fluid and a Scholte wave at the interface are observed for the cylindrical P-wave line source.

Solid lipid nanoparticles suspension versus commercial solutions for dermal delivery of minoxidil.

PubMed

Padois, Karine; Cantiéni, Céline; Bertholle, Valérie; Bardel, Claire; Pirot, Fabrice; Falson, Françoise

2011-09-15

Solid lipid nanoparticles have been reported as possible carrier for skin drug delivery. Solid lipid nanoparticles are produced from biocompatible and biodegradable lipids. Solid lipid nanoparticles made of semi-synthetic triglycerides stabilized with a mixture of polysorbate and sorbitan oleate were loaded with 5% of minoxidil. The prepared systems were characterized for particle size, pH and drug content. Ex vivo skin penetration studies were performed using Franz-type glass diffusion cells and pig ear skin. Ex vivo skin corrosion studies were realized with a method derived from the Corrositex(®) test. Solid lipid nanoparticles suspensions were compared to commercial solutions in terms of skin penetration and skin corrosion. Solid lipid nanoparticles suspensions have been shown as efficient as commercial solutions for skin penetration; and were non-corrosive while commercial solutions presented a corrosive potential. Solid lipid nanoparticles suspensions would constitute a promising formulation for hair loss treatment. Copyright © 2011 Elsevier B.V. All rights reserved.

Pallet Recycling and Material Substitution: How Will Hardwood Markets Be Affected?

Treesearch

Robert J. Bush; Philip A. Araman; Vijay S. Reddy

1997-01-01

An estimated 4.53 billion board feet of solid hardwood and 1.79 billion board feet of solid softwood were used in the production of pallets and containers in 1995. When compared to estimates for 1992, the use of both softwoods and hardwoods has decreased. Use for pallets and containers, as a percentage of total lumber production, also decreased for both materials...

Can sterile and pyrogen-free on-line substitution fluid be routinely delivered? A multicentric study on the microbiological safety of on-line haemodiafiltration.

PubMed

Vaslaki, L; Karátson, A; Vörös, P; Major, L; Pethö, F; Ladányi, E; Weber, C; Mitteregger, R; Falkenhagen, D

2000-01-01

Microbial contamination is characterized not only by the presence of bacteria, but also by high concentrations of biologically active by-products. They are potentially able to cross ultrafiltration and dialysis membranes and stimulate immunocompetent blood cells to synthesize cytokines. In turn, cytokine induction causes acute symptoms and has been incriminated in the long-term complications of haemodialysis patients. Infusion of large volumes of substitution fluids following ultrafiltration of microbially contaminated dialysis fluids may place patients on on-line therapies at particular risk. In this study we evaluated 30 machines with a two-stage ultrafiltration system in routine clinical haemodiafiltration settings in six centres for 6 months. Microbiological safety was assessed monthly and at the last use of the filters by determining microbial counts, endotoxin concentration and cytokine-inducing activity. No pyrogenic episodes were observed during the study period. Double-filtration of standard dialysis fluid (range, <1-895 cfu/ml, 0.0028-4.6822 IU/ml) resulted in sterile substitution fluids with endotoxin concentrations well below the Ph.Eur. standard for haemofiltration solutions (range, 0.0014-0.0281 vs 0.25 IU/ml). Moreover, they did not differ from commercial haemofiltration solutions and depyrogenated saline. Likewise, there was no difference in the cytokine-inducing activity between the solutions tested. The high microbiological quality of the ultrafiltered dialysis fluid, which was in the same range as substitution fluid, translates into both the absence of cytokine induction by dialyser back-transport and a redundant safety mode of the on-line system by a second filtration step. On-line HDF treatment can routinely be provided with ultra-pure dialysis fluids and sterile substitution fluids at pyrogen-free levels. The online preparation of substitution fluids thus can be considered microbiologically safe.

EQ3NR, a computer program for geochemical aqueous speciation-solubility calculations: Theoretical manual, user`s guide, and related documentation (Version 7.0); Part 3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wolery, T.J.

1992-09-14

EQ3NR is an aqueous solution speciation-solubility modeling code. It is part of the EQ3/6 software package for geochemical modeling. It computes the thermodynamic state of an aqueous solution by determining the distribution of chemical species, including simple ions, ion pairs, and complexes, using standard state thermodynamic data and various equations which describe the thermodynamic activity coefficients of these species. The input to the code describes the aqueous solution in terms of analytical data, including total (analytical) concentrations of dissolved components and such other parameters as the pH, pHCl, Eh, pe, and oxygen fugacity. The input may also include a desiredmore » electrical balancing adjustment and various constraints which impose equilibrium with special pure minerals, solid solution end-member components (of specified mole fractions), and gases (of specified fugacities). The code evaluates the degree of disequilibrium in terms of the saturation index (SI = 1og Q/K) and the thermodynamic affinity (A = {minus}2.303 RT log Q/K) for various reactions, such as mineral dissolution or oxidation-reduction in the aqueous solution itself. Individual values of Eh, pe, oxygen fugacity, and Ah (redox affinity) are computed for aqueous redox couples. Equilibrium fugacities are computed for gas species. The code is highly flexible in dealing with various parameters as either model inputs or outputs. The user can specify modification or substitution of equilibrium constants at run time by using options on the input file.« less

Polybenzimidazole compounds, polymeric media, and methods of post-polymerization modifications

DOEpatents

Klaehn, John R.; Peterson, Eric S.; Orme, Christopher J.; Jones, Michael G.; Wertsching, Alan K.; Luther, Thomas A.; Trowbridge, Tammy L.

2007-12-18

A PBI compound includes imidazole nitrogens at least a portion of which are substituted with a moiety containing a carbonyl group, the substituted imidazole nitrogens being bonded to carbon of the carbonyl group. At least 85% of the nitrogens may be substituted. The carbonyl-containing moiety may include RCO--, where R is alkoxy or haloalkyl. The PBI compound may exhibit a first temperature marking an onset of weight loss corresponding to reversion of the substituted PBI that is less than a second temperature marking an onset of decomposition of an otherwise identical PBI compound without the substituted moiety. The PBI compound may be included in separatory media. A substituted PBI synthesis method may include providing a parent PBI in a less than 5 wt % solvent solution. Substituting may use more than 5 equivalents in relation to the imidazole nitrogens to be substituted.

Synthesis of Donor/Acceptor-Substituted Diazo Compounds in Flow and Their Application in Enantioselective Dirhodium-Catalyzed Cyclopropanation and C-H Functionalization.

PubMed

Rackl, Daniel; Yoo, Chun-Jae; Jones, Christopher W; Davies, Huw M L

2017-06-16

A tandem reaction system has been developed for the preparation of donor/acceptor-substituted diazo compounds in continuous flow coupled to dirhodium-catalyzed C-H functionalization or cyclopropanation. Hydrazones were oxidized in flow by solid-supported N-iodo-p-toluenesulfonamide potassium salt (PS-SO 2 NIK) to generate the diazo compounds, which were then purified by passing through a column of molecular sieves/sodium thiosulfate.

A Solid-State NMR Study of Selenium Substitution into Nanocrystalline Hydroxyapatite

PubMed Central

Kolmas, Joanna; Kuras, Marzena; Oledzka, Ewa; Sobczak, Marcin

2015-01-01

The substitution of selenium oxyanions in the hydroxyapatite structure was examined using multinuclear solid-state resonance spectroscopy (ssNMR). The study was supported by powder X-ray diffractometry (PXRD) and wavelength dispersion X-ray fluorescence (WD-XRF). Samples of pure hydroxyapatite (HA300) and selenate (HA300-1.2SeO4) or selenite (HA300-1.2SeO3) substituted hydroxyapatites were synthesized using the standard wet method and heated at 300 °C to remove loosely bonded water. PXRD data showed that all samples are single-phase, nanocrystalline hydroxyapatite. The incorporation of selenite and selenate ions affected the lattice constants. In selenium-containing samples the concentration of Se was very similar and amounted to 9.55% and 9.64%, for HA300-1.2SeO4 and HA300-1.2SeO3, respectively. PXRD and ssNMR data showed that the selenite doping significantly decreases the crystallite size and crystallinity degree. 31P and 1H NMR experiments demonstrated the developed surface hydrated layer in all samples, especially in HA300-1.2SeO3. 1H NMR studies showed the dehydroxylation of HA during the selenium oxyanions substitution and the existence of hydrogen bonding in structural hydroxyl group channels. 1H→77Se cross polarization NMR experiments indicated that selenites and selenates are located in the crystal lattice and on the crystal surface. PMID:25997001

Photoluminescence and solid state properties of rigid pi- conjugated polymers with applications to LED: Alkyl- substituted p-phenyleneethynylene polymers and triblock copolymers

NASA Astrophysics Data System (ADS)

Huang, Wen-Yao

A series of substituted poly(p-phenyleneethynylene)s, PPE, were synthesized by alkyne metathesis. The substituents dibutyl (a), dioctyl (b), ditetradecyl (c), di-2-ethylhexyl (d) and di-2-cyclohexylethyl; (e)were placed on the 2,5 positions of the phenyl rings. X-ray diffraction studies indicated that the main chains of each polymer were arranged in regular, layered arrays. Liquid crystalline structures were observed by polarized optical microscopy in PPE 4b, 4c and 4d. The temperatures of isotropization of the liquid crystalline structures coincided with the disordering temperatures determined by differential scanning calorimetry. The UV absorption spectra showed a gradual blue shift of the λmax for all these polymers, suggesting a decrease in the electronic delocalization along the chain as the size and geometry of the side group changed. The photoluminescence spectra in dilute toluene solutions are consistent with vibronic coupling and emission from localized excited states. The emission spectra of thin films show characteristics typical of excimer or aggregate formation in the solid state. Lastly, an improved method of molecular weight determination by end group analysis was devised. Molecular organization and orientation in thin films (~100 nm) of a triblock copolymer, PPEPEG, was studied. The morphology of the thin film can be visualized as consisting of PMMA as the major phase in which domains of vertically oriented triblock copolymers are dispersed with PEG groups facing the air-film interface. The molecular and supramolecular structure of a series of well-defined fully conjugated poly(2,5- diakyl-p-phenyleneethynylene)s, PPE, in toluene has been studied in the sol state and in the gel state by surface tension and photoluminescence measurements. Poly (2,6[4- phenyl quinoline]), I, and poly (2,6[p-phenylene] 4- phenyl quinoline), II, were synthesized by the self- condensation of 5-acetyl-2-aminobezophenone and 4-amino- 4 '-acetyl-3-benzoyl biphenyl, respectively. They were soluble in acidic solvents. The fluorescent properties of I and II were investigated as a function of concentration in HCOOH, CCl2HCOOH, and CH 3SO3H solutions. Silica sol was used as nanoscale glue to prepare composite gels. (Abstract shortened by UMI.)

Substituted benzotriazoles as inhibitors of copper corrosion in borate buffer solutions

NASA Astrophysics Data System (ADS)

Agafonkina, M. O.; Andreeva, N. P.; Kuznetsov, Yu. I.; Timashev, S. F.

2017-08-01

The adsorption of substituted 1,2,3-benzotriazoles (R-BTAs) onto copper is measured via ellipsometry in a pure borate buffer (pH 7.4) and satisfactorily described by Temkin's isotherm. The adsorption free energy (-Δ G a 0 ) values of these azoles are determined. The (-Δ G a 0 ) values are found to rise as their hydrophobicity, characterized by the logarithm of the partition coefficient of a substituted BTA in a model octanol-water system (log P), grows. The minimum concentration sufficient for the spontaneous passivation of copper ( C min) and a shift in the potential of local copper depassivation with chlorides ( E pt) after an azole is added to the solution (i.e., Δ E = E pt in - E pt backgr characterizing the ability of its adsorption to stabilize passivation) are determined in the same solution containing a corrosion additive (0.01M NaCl) for each azole under study. Both criteria of the passivating properties of azoles (log C min and Δ E) are shown to correlate linearly with log P, testifying to the role played by surface activity of this family of organic inhibitors in protecting copper in an aqueous solution.

Upgraded biogas from municipal solid waste for natural gas substitution and CO{sub 2} reduction – A case study of Austria, Italy, and Spain

DOE Office of Scientific and Technical Information (OSTI.GOV)

Starr, Katherine; Villalba, Gara, E-mail: gara.villalba@uab.es; Sostenipra, Institute de Ciencia i Technologia Ambientals

2015-04-15

Highlights: • Biogas can be upgraded to create biomethane, a substitute to natural gas. • Biogas upgrading was applied to landfills and anaerobic digestors in 3 countries. • Up to 0.6% of a country’s consumption of natural gas could be replaced by biomethane. • Italy could save 46% of the national CO{sub 2} emissions attributed to the waste sector. • Scenarios were created to increase biomethane production. - Abstract: Biogas is rich in methane and can be further purified through biogas upgrading technologies, presenting a viable alternative to natural gas. Landfills and anaerobic digestors treating municipal solid waste are amore » large source of such biogas. They therefore offer an attractive opportunity to tap into this potential source of natural gas while at the same time minimizing the global warming impact resulting from methane emissions in waste management schemes (WMS) and fossil fuel consumption reduction. This study looks at the current municipal solid waste flows of Spain, Italy, and Austria over one year (2009), in order to determine how much biogas is generated. Then it examines how much natural gas could be substituted by using four different biogas upgrading technologies. Based on current waste generation rates, exploratory but realistic WMS were created for each country in order to maximize biogas production and potential for natural gas substitution. It was found that the potential substitution of natural gas by biogas resulting from the current WMS seems rather insignificant: 0.2% for Austria, 0.6% for Italy and 0.3% for Spain. However, if the WMS is redesigned to maximize biogas production, these figures can increase to 0.7% for Austria, 1% for Italy and 2% for Spain. Furthermore, the potential CO{sub 2} reduction as a consequence of capturing the biogas and replacing fossil fuel can result in up to a 93% reduction of the annual national waste greenhouse gas emissions of Spain and Italy.« less

Eutectics as improved pharmaceutical materials: design, properties and characterization.

PubMed

Cherukuvada, Suryanarayan; Nangia, Ashwini

2014-01-28

Eutectics are a long known class of multi-component solids with important and useful applications in daily life. In comparison to other multi-component crystalline solids, such as salts, solid solutions, molecular complexes and cocrystals, eutectics are less studied in terms of molecular structure organization and bonding interactions. Classically, a eutectic is defined based on its low melting point compared to the individual components. In this article, we attempt to define eutectics not just based on thermal methods but from a structural organization view point, and discuss their microstructures and properties as organic materials vis-a-vis solid solutions and cocrystals. The X-ray crystal structure of a cocrystal is different from that of the individual components whereas the unit cell of a solid solution is similar to that of one of the components. Eutectics are closer to the latter species in that their crystalline arrangement is similar to the parent components but they are different with respect to the structural integrity. A solid solution possesses structural homogeneity throughout the structure (single phase) but a eutectic is a heterogeneous ensemble of individual components whose crystal structures are like discontinuous solid solutions (phase separated). Thus, a eutectic may be better defined as a conglomerate of solid solutions. A structural analysis of cocrystals, solid solutions and eutectics has led to an understanding that materials with strong adhesive (hetero) interactions between the unlike components will lead to cocrystals whereas those having stronger cohesive (homo/self) interactions will more often give rise to solid solutions (for similar structures of components) and eutectics (for different structures of components). We demonstrate that the same crystal engineering principles which have been profitably utilized for cocrystal design in the past decade can now be applied to make eutectics as novel composite materials, illustrated by stable eutectics of the hygroscopic salt of the anti-tuberculosis drug ethambutol as a case study. A current gap in the characterization of eutectic microstructure may be fulfilled through pair distribution function (PDF) analysis of X-ray diffraction data, which could be a rapid signature technique to differentiate eutectics from their components.

Solution and solid trinitrotoluene (TNT) photochemistry: persistence of TNT-like ultraviolet (UV) resonance Raman bands.

PubMed

Gares, Katie L; Bykov, Sergei V; Godugu, Bhaskar; Asher, Sanford A

2014-01-01

We examined the 229 nm deep-ultraviolet resonance Raman (DUVRR) spectra of solution and solid-state trinitrotoluene (TNT) and its solution and solid-state photochemistry. Although TNT photodegrades with a solution quantum yield of ϕ ∼ 0.015, the initial photoproducts show DUVRR spectra extraordinarily similar to pure TNT, due to the similar photoproduct enhancement of the -NO2 stretching vibrations. This results in TNT-like DUVRR spectra even after complete TNT photolysis. These ultraviolet resonance Raman spectral bands enable DUVRR of trace as well as DUVRR standoff TNT detection. We determined the structure of various initial TNT photoproducts by using liquid chromatography-mass spectrometry and tandem mass spectrometry. Similar TNT DUVRR spectra and photoproducts are observed in the solution and solid states.

NEUTRALIZATIONS OF HIGH ALUMINUM LOW URANIUM USED NUCLEAR FUEL SOLUTIONS CONTAINING GADOLINIUM AS A NEUTRON POISON

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor-Pashow, K.

2011-06-08

H-Canyon will begin dissolving High Aluminum - Low Uranium (High Al/Low U) Used Nuclear Fuel (UNF) following approval by DOE which is anticipated in CY2011. High Al/Low U is an aluminum/enriched uranium UNF with small quantities of uranium relative to aluminum. The maximum enrichment level expected is 93% {sup 235}U. The High Al/Low U UNF will be dissolved in H-Canyon in a nitric acid/mercury/gadolinium solution. The resulting solution will be neutralized and transferred to Tank 39H in the Tank Farm. To confirm that the solution generated could be poisoned with Gd, neutralized, and discarded to the Savannah River Site (SRS)more » high level waste (HLW) system without undue nuclear safety concerns the caustic precipitation of simulant solutions was examined. Experiments were performed with three simulant solutions representative of the H-Canyon estimated concentrations in the final solutions after dissolution. The maximum U, Gd, and Al concentration were selected for testing from the range of solution compositions provided. Simulants were prepared in three different nitric acid concentrations, ranging from 0.5 to 1.5 M. The simulant solutions were neutralized to four different endpoints: (1) just before a solid phase was formed (pH 3.5-4), (2) the point where a solid phase was obtained, (3) 0.8 M free hydroxide, and (4) 1.2 M free hydroxide, using 50 wt % sodium hydroxide (NaOH). The settling behavior of the neutralized solutions was found to be slower compared to previous studies, with settling continuing over a one week period. Due to the high concentration of Al in these solutions, precipitation of solids was observed immediately upon addition of NaOH. Precipitation continued as additional NaOH was added, reaching a point where the mixture becomes almost completely solid due to the large amount of precipitate. As additional NaOH was added, some of the precipitate began to redissolve, and the solutions neutralized to the final two endpoints mixed easily and had expected densities of typical neutralized waste. Based on particle size and scanning electron microscopy analyses, the neutralized solids were found to be homogeneous and less than 20 microns in size. The majority of solids were less than 4 microns in size. Compared to previous studies, a larger percentage of the Gd was found to precipitate in the partially neutralized solutions (at pH 3.5-4). In addition the Gd:U mass ratio was found to be at least 1.0 in all of the solids obtained after partial or full neutralization. The hydrogen to U (H:U) molar ratios for two accident scenarios were also determined. The first was for transient neutralization and agitator failure. Experimentally this scenario was determined by measuring the H:U ratio of the settled solids. The minimum H:U molar ratio for solids from fully neutralized solutions was 388:1. The second accident scenario is for the solids drying out in an unagitiated pump box. Experimentally, this scenario was determined by measuring the H:U molar ratio in centrifuged solids. The minimum H:U atom ratios for centrifuged precipitated solids was 250:1. It was determined previously that a 30:1 H:Pu atom ratio was sufficient for a 1:1 Gd:Pu mass ratio. Assuming a 1:1 equivalence with {sup 239}Pu, the results of these experiments show Gd is a viable poison for neutralizing U/Gd solutions with the tested compositions.« less

Metal Substitution in Keggin-Type Tridecameric Aluminum-Oxo-Hydroxy Clusters.

PubMed

Parker, Wallace O'Neil; Millini, Roberto; Kiricsi, Imre

1997-02-12

The species resulting from a typical preparation for metal-substituted hybrids of the Keggin tridecamer, Al 13 or [AlO 4 Al 12 (OH) 24 (OH 2 ) 12 ] 7+ , were examined by performing 27 Al NMR on the solutions during aging and by studying the precipitated sulfate salts via solid state 27 Al NMR and powder X-ray diffraction (XRD). Aqueous mixtures (0.25 mol L -1 ) of AlCl 3 and another metal ion (M), in a 12:1 mole ratio (Al:M), where M = Fe 3+ , Zn 2+ , Ga 3+ , In 3+ , Sn 2+ , La 3+ , and Bi 3+ , were subjected to forced hydrolysis by addition of NaOH (1.0 mol L -1 ) until OH/(Al + M) = 2.25, and the kinetics of Al 13 formation and disappearance with aging at 80 °C was monitored by 27 Al NMR spectroscopy. Al 13 units polymerize on aging with an apparent rate constant (k) of 4.8(8) × 10 -2 h -1 to form a species referred to as AlP 2 . Only the solutions containing Ga 3+ and Sn 2+ exhibited faster Al 13 conversion rates. GaAl 12 forms quickly at 80 °C (k = 0.54 h -1 ) and is more stable than AlP 2 . Sn 2+ apparently promotes AlP 2 formation (k = 0.38 h -1 ). XRD and solid state NMR reveal that only the Ga hybrid can be prepared by this method. No hybrid formation was evidenced using M = Mg 2+ , Fe 3+ , Co 2+ , Ni 2+ , Cu 2+ , Zn 2+ , In 3+ , La 3+ , or Ce 3+ at 25 °C or M = Co 2+ or La 3+ under reflux conditions. Isostructural (cubic symmetry) single crystals were obtained for the sulfate salts of Al 13 and GaAl 12 . Single-crystal XRD analysis of these two polyoxocations provides the first rigorous comparison between them and shows they have very similar structures. The main crystallographic data for Al 13 and GaAl 12 are as follows:  Na[AlO 4 Al 12 (OH) 24 (H 2 O) 12 ](SO 4 ) 4 ·10H 2 O, cubic, F4̄3m, a = 17.856(2) Å, Z = 4; Na[GaO 4 Al 12 (OH) 24 (H 2 O) 12 ](SO 4 ) 4 ·10H 2 O, cubic, F4̄3m, a = 17.869(3) Å, Z = 4. Thus, the greater thermal stability of GaAl 12 cannot be rationalized in terms of the overall geometric considerations, as suggested by others. Solid state NMR also shows the coordination symmetries of the outer 12 Al nuclei in both clusters to be similar.

21 CFR 172.838 - Polysorbate 65.

Code of Federal Regulations, 2012 CFR

2012-04-01

... solid-state, edible vegetable fat-water emulsions intended for use as substitutes for milk or cream in... finished edible vegetable fat-water emulsion. (5) As an emulsifier in cake icings and cake fillings, with...

21 CFR 172.838 - Polysorbate 65.

Code of Federal Regulations, 2013 CFR

2013-04-01

... solid-state, edible vegetable fat-water emulsions intended for use as substitutes for milk or cream in... finished edible vegetable fat-water emulsion. (5) As an emulsifier in cake icings and cake fillings, with...

An Overview of Pickering Emulsions: Solid-Particle Materials, Classification, Morphology, and Applications

PubMed Central

Yang, Yunqi; Fang, Zhiwei; Chen, Xuan; Zhang, Weiwang; Xie, Yangmei; Chen, Yinghui; Liu, Zhenguo; Yuan, Weien

2017-01-01

Pickering emulsion, a kind of emulsion stabilized only by solid particles locating at oil–water interface, has been discovered a century ago, while being extensively studied in recent decades. Substituting solid particles for traditional surfactants, Pickering emulsions are more stable against coalescence and can obtain many useful properties. Besides, they are more biocompatible when solid particles employed are relatively safe in vivo. Pickering emulsions can be applied in a wide range of fields, such as biomedicine, food, fine chemical synthesis, cosmetics, and so on, by properly tuning types and properties of solid emulsifiers. In this article, we give an overview of Pickering emulsions, focusing on some kinds of solid particles commonly serving as emulsifiers, three main types of products from Pickering emulsions, morphology of solid particles and as-prepared materials, as well as applications in different fields. PMID:28588490

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maughan, Annalise E.; Ganose, Alex M.; Bordelon, Mitchell M.

Vacancy-ordered double perovskites of the general formula, A2BX6, are a family of perovskite derivatives composed of a face-centered lattice of nearly isolated [BX6] units with A-site cations occupying the cuboctahedral voids. Despite the presence of isolated octahedral units, the close-packed iodide lattice provides significant electronic dispersion, such that Cs2SnI6 has recently been explored for applications in photovoltaic devices. To elucidate the structure-property relationships of these materials, we have synthesized the solid solution Cs2Sn1-xTexI6. However, even though tellurium substitution increases electronic dispersion via closer I-I contact distances, the substitution experimentally yields insulating behavior from a significant decrease in carrier concentration andmore » mobility. Density functional calculations of native defects in Cs2SnI6 reveal that iodine vacancies exhibit a low enthalpy of formation and the defect energy level is a shallow donor to the conduction band, rendering the material tolerant to these defect states. The increased covalency of Te-I bonding renders the formation of iodine vacancy states unfavorable, and is responsible for the reduction in conductivity upon Te substitution. Additionally, Cs2TeI6 is intolerant to the formation of these defects, as the defect level occurs deep within the band gap and thus localizes potential mobile charge carriers. In these vacancy-ordered double perovskites, the close-packed lattice of iodine provides significant electronic dispersion, while the interaction of the B- and X-site ions dictates the properties as they pertain to electronic structure and defect tolerance. This simplified perspective -- based on extensive experimental and theoretical analysis -- provides a platform from which to understand structure-property relationships in functional perovskite halides.« less

Low cost stable air electrode material for high temperature solid oxide electrolyte electrochemical cells

DOEpatents

Kuo, L.J.H.; Singh, P.; Ruka, R.J.; Vasilow, T.R.; Bratton, R.J.

1997-11-11

A low cost, lanthanide-substituted, dimensionally and thermally stable, gas permeable, electrically conductive, porous ceramic air electrode composition of lanthanide-substituted doped lanthanum manganite is provided which is used as the cathode in high temperature, solid oxide electrolyte fuel cells and generators. The air electrode composition of this invention has a much lower fabrication cost as a result of using a lower cost lanthanide mixture, either a natural mixture or an unfinished lanthanide concentrate obtained from a natural mixture subjected to incomplete purification, as the raw material in place of part or all of the higher cost individual lanthanum. The mixed lanthanide primarily contains a mixture of at least La, Ce, Pr, and Nd, or at least La, Ce, Pr, Nd and Sm in its lanthanide content, but can also include minor amounts of other lanthanides and trace impurities. The use of lanthanides in place of some or all of the lanthanum also increases the dimensional stability of the air electrode. This low cost air electrode can be fabricated as a cathode for use in high temperature, solid oxide fuel cells and generators. 4 figs.

Low cost stable air electrode material for high temperature solid oxide electrolyte electrochemical cells

DOEpatents

Kuo, Lewis J. H.; Singh, Prabhakar; Ruka, Roswell J.; Vasilow, Theodore R.; Bratton, Raymond J.

1997-01-01

A low cost, lanthanide-substituted, dimensionally and thermally stable, gas permeable, electrically conductive, porous ceramic air electrode composition of lanthanide-substituted doped lanthanum manganite is provided which is used as the cathode in high temperature, solid oxide electrolyte fuel cells and generators. The air electrode composition of this invention has a much lower fabrication cost as a result of using a lower cost lanthanide mixture, either a natural mixture or an unfinished lanthanide concentrate obtained from a natural mixture subjected to incomplete purification, as the raw material in place of part or all of the higher cost individual lanthanum. The mixed lanthanide primarily contains a mixture of at least La, Ce, Pr, and Nd, or at least La, Ce, Pr, Nd and Sm in its lanthanide content, but can also include minor amounts of other lanthanides and trace impurities. The use of lanthanides in place of some or all of the lanthanum also increases the dimensional stability of the air electrode. This low cost air electrode can be fabricated as a cathode for use in high temperature, solid oxide fuel cells and generators.

Process for recovering pertechnetate ions from an aqueous solution also containing other ions

DOEpatents

Rogers, Robin; Horwitz, E. Philip; Bond, Andrew H.

1997-01-01

A solid/liquid process for the separation and recovery of TcO.sub.4.sup.-1 ions from an aqueous solution is disclosed. The solid support comprises separation particles having surface-bonded poly(ethylene glycol) groups; whereas the aqueous solution from which the TcO.sub.4.sup.-1 ions are separated contains a poly(ethylene glycol) liquid/liquid biphase-forming amount of a dissolved salt. A solid/liquid phase admixture of separation particles containing bound TcO.sub.4.sup.-1 ions in such an aqueous solution that is free from MoO.sub.4.sup.-2 ions is also contemplated, as is a chromatography apparatus containing that solid/liquid phase admixture.

Mechanisms for monovalent cation-dependent depletion of intracellular Mg2+:Na(+)-independent Mg2+ pathways in guinea-pig smooth muscle.

PubMed

Nakayama, Shinsuke; Nomura, Hideki; Smith, Lorraine M; Clark, Joseph F; Uetani, Tadayuki; Matsubara, Tatsuaki

2003-09-15

It has been suggested that magnesium deficiency is correlated with many diseases. 31P NMR experiments were carried out in order to investigate the effects of Na+ substitution on Mg2+ depletion in smooth muscle under divalent cation-free conditions. In the taenia of guinea-pig caeci, the intracellular free Mg2+ concentration ([Mg2+]i) was estimated from the chemical shifts of (1) the beta-ATP peak alone and (2) beta- and gamma-ATP peaks. Both estimations indicated that [Mg2+]i decreased only very slowly in Mg(2+)-free, Ca(2+)-free solutions in which Na+ was substituted with large cations such as NMDG (N-methyl-D-glucamine) and choline. Furthermore, the measurements of tension development supported the suggestion of preservation of intracellular Mg2+ with NMDG substitution. Substituting extracellular Na+ with the small cation, Li+, also shifted the beta-ATP peak towards a lower frequency, but the frequency shift was significantly less than that seen upon Na+ substitution with K+. The estimated [Mg2+]i depletion was, however, comparable with that seen after Na+ substitution with K+ using the titration curves of metal-free and Mg(2+)-bound ATP obtained in Li(+)-based model solutions. It was concluded that Mg2+ rapidly decreases only when small cations were the major electrolyte of the extracellular medium. Na+ substitutions with NMDG, choline or Li+ had little effect on intracellular ATP concentration after 100 min treatment.

The Systematics of Activity-Composition Relations in Mg-Fe2+ Oxide and Silicate Solid Solutions

NASA Astrophysics Data System (ADS)

O'Neill, H. S.

2006-12-01

The need to quantify activity-composition relations of mineral solid solutions for petrologic modelling has prompted many experimental studies, but different studies on the same system often appear to show a startling lack of consistency. A good example is Mg-Fe2+ mixing in garnet (the pyrope-almandine join). This is understandable because the energies of mixing in solid solutions are often obtained experimentally as small difference between large numbers. In particular, the fallacy of using a sequential approach to data fitting to a thermodynamic model leads to the accumulated errors being artificially concentrated onto the last step of the fitting process, which is usually that part of the model dealing with the excess energies of mixing. This gives rise to erroneous activity-composition relations, often apparently showing complex deviations from ideality. Systemizing the results of many studies can reveal underlying patterns of behaviour while also identifying outliers and anomalies that may be worth reinvestigating. Davies and Navrotsky [1] showed that the energies of mixing of many different pairs of ions with the same charge correlated well with the difference in molar volumes of the end-members, within a particular crystal structure. This empirical work is now supported by theoretical calculations. It underlies the modern approach to melt/crystal trace-element partitioning. Provided an internally consistent dataset is used, an analogous correlation may be demonstrated across different crystal structures for the mixing of one pair of ions, such as Mg and Fe2+. Activity-composition relations in MgO-"FeO" magnesiowuestite solutions in equilibrium with iron metal were used to obtain the properties of Mg-Fe olivine solutions from magnesiowuestite/olivine partitioning [2]. New results at 1400 K, 1 bar and 1473 K, 25 kb (O'Neill and Pownceby, in prep.) confirm previous work that mixing in Mg-Fe olivine is regular (symmetrical) with W Mg-Fe = 2.5 kJ/mol, with an accuracy including possible systematic errors of 0.5 kJ/mol (1 st. dev.). Any asymmetry is unambiguously constrained to be very small. These results were combined with experimental data (all at or above 900ºC), for partitioning of Mg and Fe between olivine and one of ilmenite (Pownceby and O'Neill, in prep.), Ti-, Al- or Cr-spinel (O'Neill, unpublished) and pyroxenes, garnet, and various high-pressure phases (literature). Internal consistency can be checked using other available partitioning data between pairs of these phases (i.e., without olivine). Except for some of the high-pressure phases, the ferromagnesian solutions are symmetrical with W Mg-Fe decreasing with the difference in the volumes of the end-members, which in turn depends on the atomic (Mg+Fe)/O ratio. This suggests that mixing in binary amphiboles, micas and other complex ferromagnesian silicates should be nearly ideal. The discrepancies shown by the high-pressure phases may be due to Fe3+ substitutions. As a working hypothesis, it is proposed that solid solutions between cations of the same charge and roughly similar size have simple thermodynamic mixing properties, with little asymmetry, modest excess entropies and excess enthalpies proportional to the volume difference of the end-members. Order-disorder phenomena have surprisingly little effect in the high temperature regime for which experimental data are available. Refs: [1] Davies and Navrotsky, J Sol State Chem 46, 1-22, 1983. [2] O'Neill et al., CMP 146, 308-325, 2003.

LEACHING OF TITANIUM FROM MONOSODIUM TITANATE AND MODIFIED MST

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor-Pashow, K.; Fondeur, F.; Fink, S.

2012-08-01

Analysis of a fouled coalescer and pre-filters from Actinide Removal Process/Modular Caustic Side Solvent Extraction Unit (ARP/MCU) operations showed evidence of Ti containing solids. Based on these results a series of tests were planned to examine the extent of Ti leaching from monosodium titanate (MST) and modified monosodium titanate (mMST) in various solutions. The solutions tested included a series of salt solutions with varying free hydroxide concentrations, two sodium hydroxide concentrations, 9 wt % and 15 wt %, nitric and oxalic acid solutions. Overall, the amount of Ti leached from the MST and mMST was much greater in the acidmore » solutions compared to the sodium hydroxide or salt solutions, which is consistent with the expected trend. The leaching data also showed that increasing hydroxide concentration, whether pure NaOH solution used for filter cleaning in ARP or the waste salt solution, increased the amount of Ti leached from both the MST and mMST. For the respective nominal contact times with the MST solids - for filter cleaning or the normal filter operation, the dissolved Ti concentrations are comparable suggesting either cause may contribute to the increased Ti fouling on the MCU coalescers. Tests showed that Ti containing solids could be precipitated from solution after the addition of scrub acid and a decrease in temperature similar to expected in MCU operations. FTIR analysis of these solids showed some similarity to the solids observed on the fouled coalescer and pre-filters. Although only a cursory study, this information suggests that the practice of increasing free hydroxide in feed solutions to MCU as a mitigation to aluminosilicate formation may be offset by the impact of formation of Ti solids in the overall process. Additional consideration of this finding from MCU and SWPF operation is warranted.« less

A study of a tissue equivalent gelatine based tissue substitute

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spence, J.L.

1992-11-01

A study of several tissue substitutes for use as volumetric dosimeters was performed. The tissue substitutes studied included tissue substitutes from previous studies and from ICRU 44. The substitutes were evaluated for an overall match to Reference Man which was used as a basis for this study. The evaluation was based on the electron stopping power, the mass attenuation coefficient, the electron density, and the specific gravity. The tissue substitute chosen also had to be capable of changing from a liquid into a solid form to maintain an even distribution of thermoluminesent dosimetry (TLD) powder and then back to amore » liquid for recovery of the TLD powder without adversely effecting the TLD powder. The gelatine mixture provided the closest match to the data from Reference Man tissue. The gelatine mixture was put through a series of test to determine it's usefulness as a reliable tissue substitute. The TLD powder was cast in the gelatine mixture and recovered to determine if the TLD powder was adversely effected. The distribution of the TLD powder after being cast into the gelatin mixture was tested in insure an even was maintained.« less

A study of a tissue equivalent gelatine based tissue substitute

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spence, Jody L.

1992-11-01

A study of several tissue substitutes for use as volumetric dosimeters was performed. The tissue substitutes studied included tissue substitutes from previous studies and from ICRU 44. The substitutes were evaluated for an overall match to Reference Man which was used as a basis for this study. The evaluation was based on the electron stopping power, the mass attenuation coefficient, the electron density, and the specific gravity. The tissue substitute chosen also had to be capable of changing from a liquid into a solid form to maintain an even distribution of thermoluminesent dosimetry (TLD) powder and then back to amore » liquid for recovery of the TLD powder without adversely effecting the TLD powder. The gelatine mixture provided the closest match to the data from Reference Man tissue. The gelatine mixture was put through a series of test to determine it`s usefulness as a reliable tissue substitute. The TLD powder was cast in the gelatine mixture and recovered to determine if the TLD powder was adversely effected. The distribution of the TLD powder after being cast into the gelatin mixture was tested in insure an even was maintained.« less

Enhanced hot-carrier cooling and ultrafast spectral diffusion in strongly coupled PbSe quantum-dot solids.

PubMed

Gao, Yunan; Talgorn, Elise; Aerts, Michiel; Trinh, M Tuan; Schins, Juleon M; Houtepen, Arjan J; Siebbeles, Laurens D A

2011-12-14

PbSe quantum-dot solids are of great interest for low cost and efficient photodetectors and solar cells. We have prepared PbSe quantum-dot solids with high charge carrier mobilities using layer-by-layer dip-coating with 1,2-ethanediamine as substitute capping ligands. Here we present a time and energy resolved transient absorption spectroscopy study on the kinetics of photogenerated charge carriers, focusing on 0-5 ps after photoexcitation. We compare the observed carrier kinetics to those for quantum dots in dispersion and show that the intraband carrier cooling is significantly faster in quantum-dot solids. In addition we find that carriers diffuse from higher to lower energy sites in the quantum-dot solid within several picoseconds.

Solid lithium ion conducting electrolytes and methods of preparation

DOEpatents

Narula, Chaitanya K; Daniel, Claus

2013-05-28

A composition comprised of nanoparticles of lithium ion conducting solid oxide material, wherein the solid oxide material is comprised of lithium ions, and at least one type of metal ion selected from pentavalent metal ions and trivalent lanthanide metal ions. Solution methods useful for synthesizing these solid oxide materials, as well as precursor solutions and components thereof, are also described. The solid oxide materials are incorporated as electrolytes into lithium ion batteries.

Solid lithium ion conducting electrolytes and methods of preparation

DOEpatents

Narula, Chaitanya K.; Daniel, Claus

2015-11-19

A composition comprised of nanoparticles of lithium ion conducting solid oxide material, wherein the solid oxide material is comprised of lithium ions, and at least one type of metal ion selected from pentavalent metal ions and trivalent lanthanide metal ions. Solution methods useful for synthesizing these solid oxide materials, as well as precursor solutions and components thereof, are also described. The solid oxide materials are incorporated as electrolytes into lithium ion batteries.

INTERNATIONAL CONFERENCE ON SEMICONDUCTOR INJECTION LASERS SELCO-87: Simple formula for the thermal conductivity of a quaternary solid solution

NASA Astrophysics Data System (ADS)

Nakwaski, W.

1988-11-01

An analysis is made of the thermal conductivity of quaternary solid solutions (alloys) allowing for their disordered structure on the basis of a phenomenological analysis proposed by Abeles. This method is applied to a quaternary solid solution In1 - xGaxAsyP1 - y. A simple analytic expression is derived for the thermal conductivity of this material.

Lattice Parameter Behavior with Different Nd and O Concentrations in (U 1-yNd y)O 2±x Solid Solution

DOE PAGES

Lee, Seung Min; Knight, Travis W.; Voit, Stwart L.; ...

2016-02-02

The solid solution of (U1-yFPy)O- 2±x, has the same fluorite structure as UO 2±x lambda, and the lattice parameter is affected by dissolved fission product and oxygen concentrations. We investigated the relation between the lattice parameter and the concentrations of neodymium and oxygen in the fluorite structure of (U 1-yNd y)O 2±x using X-ray diffraction. Moreover, the lattice parameter behavior in the (U 1-yNd y)O 2±x, solid solution shows a linear change as a function of the oxygen-to-metal ratio and solubility of neodymium. The lattice parameter depends on the radii of ions forming the fluorite structure and also can bemore » expressed by a particular rule (modified Vegard's law). Furthermore, the numerical analyses of the lattice parameters for the stoichiometric and nonstoichionietric solid solutions were conducted, and the lattice parameter model for the (U1-yNdy)O 2±x, solid solution was assessed. There is a very linear relationship between the lattice parameter and the Nd and O concentration for the stoichiometry and nonstoichiometry of the (U 1-yNd y)O 2±x solid solution was verified.« less

Revisiting HgCl 2: A solution- and solid-state 199Hg NMR and ZORA-DFT computational study

NASA Astrophysics Data System (ADS)

Taylor, R. E.; Carver, Colin T.; Larsen, Ross E.; Dmitrenko, Olga; Bai, Shi; Dybowski, C.

2009-07-01

The 199Hg chemical-shift tensor of solid HgCl 2 was determined from spectra of polycrystalline materials, using static and magic-angle spinning (MAS) techniques at multiple spinning frequencies and field strengths. The chemical-shift tensor of solid HgCl 2 is axially symmetric ( η = 0) within experimental error. The 199Hg chemical-shift anisotropy (CSA) of HgCl 2 in a frozen solution in dimethylsulfoxide (DMSO) is significantly smaller than that of the solid, implying that the local electronic structure in the solid is different from that of the material in solution. The experimental chemical-shift results (solution and solid state) are compared with those predicted by density functional theory (DFT) calculations using the zeroth-order regular approximation (ZORA) to account for relativistic effects. 199Hg spin-lattice relaxation of HgCl 2 dissolved in DMSO is dominated by a CSA mechanism, but a second contribution to relaxation arises from ligand exchange. Relaxation in the solid state is independent of temperature, suggesting relaxation by paramagnetic impurities or defects.

Study of structural, electrical, magnetic and optical properties of BaFe12O19 and its modified systems with Ni and Ti

NASA Astrophysics Data System (ADS)

Nayak, Debabrata; Pattanayak, Ranjit; Raut, Subhajit; Panigrahi, Simanchalo

2018-02-01

In this work, BaFe12O19 (BaM) and its modified systems (by substitution of Ni and Ti) have been synthesized by solid-state reaction method. From Rietveld refinement of X-ray diffraction pattern, it is found that volume of unit cell increased slightly in case of modified systems. SEM images provided the information about the microstructure of BaM and its modified systems. The electric, magnetic and optical properties have been carried out with the help of complex impedance spectroscopy, VSM and UV spectrum, respectively. From electrical analysis, it is perceived that Ni-substitution system has shown co-contribution of grain and grain boundary effect due to increases of grain size. The M- H loops are explored that, with substitution of Ni and Ti both M s and H c are decreased. From the variation of band gap ( E g), it is observed that E g has been significantly decreased with substitution (least for Ni-substitution).

Magnetism and Solid Solution Effects in NiAI (40% AI) Alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Chain T; Fu, Chong Long; Chisholm, Matthew F

2007-01-01

The solid solution effects of ternary additions of transition elements in intermetallic Ni-40% Al were investigated by both experimental studies and theoretical calculations. Co solute atoms when sitting at Ni sublattice sites do not affect the lattice parameter and hardening behavior of Ni-40Al. On the other hand, Fe, Mn, and Cr solutes, which are mainly on Al sublattice sites, substantially expand the lattice parameter and produce an unusual solid solution softening effect. First-principles calculations predict that these solute atoms with large unfilled d-band electrons develop large magnetic moments and effectively expand the lattice parameter when occupying Al sublattice sites. Themore » theoretical predictions were verified by both electron loss-energy spectroscopy (EELS) analyses and magnetic susceptibility measurements. The observed softening behavior can be explained quantitatively by the replacement of Ni anti-site defects (potent hardeners) by Fe, Mn, and Cr anti-site defects with smaller atom size mismatch between solute and Al atoms. This study has led to the identification of magnetic interaction as an important physical parameter affecting the solid solution hardening in intermetallic alloys containing transition elements.« less

Development of a polymeric ionic liquid coating for direct-immersion solid-phase microextraction using polyhedral oligomeric silsesquioxane as cross-linker.

PubMed

Chen, Chunyan; Liang, Xiaotong; Wang, Jianping; Zou, Ying; Hu, Huiping; Cai, Qingyun; Yao, Shouzhuo

2014-06-27

A novel solid-phase microextraction (SPME) fiber was developed by chemical binding of a crosslinked polymeric ionic liquid (PIL) on the surface of an anodized Ti wire, and was applied in direct-immersion mode for the extraction of perfluorinated compounds (PFCs) from water samples coupled with high performance liquid chromatography-tandem mass spectrometry analysis. The PIL coatings were synthesized by using 1-vinyl-3-hexylimidazolium hexafluorophosphate as monomer and methylacryloyl-substituted polyhedral oligomeric silsesquioxane (POSS) as cross-linker via free radical reaction. The proposed fiber coating exhibited high mechanical stability due to the chemical bonding between the coating and the Ti wire surface. The integration of POSS reagent enhanced the organic solvent resistance of the coating. The parameters affecting the extraction performance of the fiber coating including extraction time, pH of solution, ionic strength and desorption conditions were optimized. The developed PIL-POSS fiber showed good linearity (R<0.998) between 0.1 and 50ngmL(-1) with method detection limits ranging from 0.005 to 0.08ngmL(-1) depending on the analyte, and with relative standard deviation for single-fiber repeatability and fiber-to-fiber reproducibility less than 8.6% and 9.5%, respectively. Copyright © 2014 Elsevier B.V. All rights reserved.

Bioinspired polydopamine sheathed nanofibers for high-efficient in vivo solid-phase microextraction of pharmaceuticals in fish muscle.

PubMed

Xu, Jianqiao; Huang, Shuyao; Wu, Rongben; Jiang, Ruifen; Zhu, Fang; Wang, Jing; Ouyang, Gangfeng

2015-03-17

In this study, electrospun nanofibers were used as solid-phase microextraction (SPME) fiber coatings after substituting the water-soluble sheath of the emulsion electrospun polystyrene (PS)@Plurinic F-127 core-sheath nanofibers with biocompatible and water-stable polydopamine (PDA) and subsequently being appropriately cross-linked with glutaraldehyde (GA) to enhance the strength of the electrospun architecture. The novel custom-made PS@PDA-GA coating was wettable in aqueous solutions and thus exhibited much higher extraction efficiency than the nonsheathed PS nanofiber coating and the thicker polydimethylsiloxane (PDMS) coating. The novel coating also possessed excellent stability (relative standard deviations (RSDs) less than 7.3% for six sampling-desorption cycles), interfiber reproducibility (RSDs less than 14.3%), and antibiofouling ability, which were beneficial for in vivo sampling. The PS@PDA-GA fiber was used to monitor pharmaceuticals in dorsal-epaxial muscle of living fish, and satisfactory sensitivities with the limits of detection in the range of 1.1 (mefenamic acid) to 8.9 (fluoxetine) ng·g(-1) and comparable accuracies to liquid extraction were achieved. In general, this study explored a convenient and effective method to sheath nanofibers for high-efficient in vivo SPME of analytes of interest in semisolid tissues.

Synthesis and Thermoelectric Properties in the 2D Ti1 – xNbxS3 Trichalcogenides

PubMed Central

Misse, Patrick R. N.; Berthebaud, David; Lebedev, Oleg I.; Maignan, Antoine; Guilmeau, Emmanuel

2015-01-01

A solid solution of Ti1 − xNbxS3 composition (x = 0, 0.05, 0.07, 0.10) was synthesized by solid-liquid-vapor reaction followed by spark plasma sintering. The obtained compounds crystallize in the monoclinic ZrSe3 structure type. For the x = 0.07 sample, a mixture of both A and B variants of the MX3 structure is evidenced by transmission electron microscopy. This result contrasts with those of pristine TiS3, prepared within the same conditions, which crystallizes as a large majority of A variant. Thermoelectric properties were investigated in the temperature range 323 to 523 K. A decrease in the electrical resistivity and absolute value of the Seebeck coefficient is observed when increasing x due to electron doping. The lattice component of the thermal conductivity is effectively reduced by the Nb for Ti substitution through a mass fluctuation effect and/or a disorder effect created by the mixture of both A and B variants. Due to the low carrier concentration and the semiconductor character of the doped compounds, the too low power factor values leads to ZT values that remain smaller by a factor of 50 than those of the TiS2 layered compound.

Ion exchange polymers for anion separations

DOEpatents

Jarvinen, Gordon D.; Marsh, S. Fredric; Bartsch, Richard A.

1997-01-01

Anion exchange resins including at least two positively charged sites and a ell-defined spacing between the positive sites are provided together with a process of removing anions or anionic metal complexes from aqueous solutions by use of such resins. The resins can be substituted poly(vinylpyridine) and substituted polystyrene.

Ion exchange polymers for anion separations

DOEpatents

Jarvinen, G.D.; Marsh, S.F.; Bartsch, R.A.

1997-09-23

Anion exchange resins including at least two positively charged sites and a well-defined spacing between the positive sites are provided together with a process of removing anions or anionic metal complexes from aqueous solutions by use of such resins. The resins can be substituted poly(vinylpyridine) and substituted polystyrene.

Manganese As a Metal Accumulator

EPA Science Inventory

Manganese deposits in water distribution systems accumulate metals, radionuclides and oxyanions by a combination of surface complexation, adsorption and solid substitution, as well as a combination of oxidation followed by manganese reduction and sorption of the oxidized constitu...

Influence of Fe-substitution on structural, magnetic and magnetocaloric properties of Nd2Fe17-xCox solid solutions

NASA Astrophysics Data System (ADS)

Bouchaala, N.; Jemmali, M.; Bartoli, T.; Nouri, K.; Hentech, I.; Walha, S.; Bessais, L.; Salah, A. Ben

2018-02-01

Nd2Fe17-xCox (x = 0 , 1 , 2 , 3 , 4) intermetallic compounds, obtained under arc-melting conditions, have been investigated by means of X-ray diffraction analysis (XRD), Mössbauer spectrometry and magnetic measurements. The Rietveld refinement revealed that the sample is a pure compound with rhombohedral Th2Zn17-type structure (R 3 bar m space group) with the following lattice parameters: a = 8.5792 (2) Å, c = 12.4615 (2) Å. Using Mössbauer spectrometry analysis coupled with structural consideration we have unambiguously determined the cobalt atoms preferred inequivalent crystallographic site. Nd2Fe17 show an increase of 3.5 T in their weighted average hyperfine fields upon cobalt substitution. Whatever the cobalt content, the hyperfine field of these compounds follow this sequence Hhf { 6 c } >Hhf { 9 d } >Hhf { 18 f } >Hhf { 18 h }. The magnetic measurements showed that the Curie temperature increases with the Co content. The magnetic entropy change (ΔSM) was estimated from isothermal magnetization curves and it increases from 3.35 J/Kg K for x = 0 to 5.83 J/Kg K for x = 2 at μ0 H = 1.6 T . The relative cooling power (RCP) is in the range of 11.6 J/kg (x = 0) and 16 J/kg (x = 2).

Enhanced water purification: a single atom makes a difference.

PubMed

Stewart, Tom A; Trudell, Daniel E; Alam, Todd M; Ohlin, C André; Lawler, Christian; Casey, William H; Jett, Stephen; Nyman, May

2009-07-15

The aluminum Keggin polycation (Al13) has been identified as an effective specie for neutralization and coagulation of anionic contaminants in water. In this study, we compare efficacy of the aluminum Keggin-ion to the analogues containing a single Ga-atom or single Ge-atom (GaAl12 and GeAl12, respectively) substituted into the center of the polycation in water-treatment studies. We investigated removal of bacteriophage (model viruses), Cryptosporidium, dissolved organic carbon (DOC), and turbidity. In every study, the order of contaminant removal efficacy trends GaAl12 > Al13 > GeAl12. By ESI MS (electrospray ionization mass spectrometry), we noted the GaAl12 deprotonates least of the three aluminum polycations, and thus probably carries the highest charge, and also optimal contaminant-neutralization ability. The ESI MS studies of the aluminum polycation solutions, as well as solid-state characterization of their resulting precipitates both reveal some conversion of Al13 to larger polycations, Al30 for instance. The GaAl12 does not show any evidence for this alteration that is responsible for poor shelf life of commercial prehydrolyzed aluminum coagulants such as polyaluminum chloride. Based on these studies, we conclude that substitution of a single Ga-atom in the center of the aluminum Keggin polycation produces an optimal water-treatment product due to enhanced shelf life and efficacy in neutralization of anionic contaminants.

Engineering the Structural and Electronic Phases of MoTe2 through W Substitution

NASA Astrophysics Data System (ADS)

Rhodes, D.; Chenet, D. A.; Janicek, B. E.; Nyby, C.; Lin, Y.; Jin, W.; Edelberg, D.; Mannebach, E.; Finney, N.; Antony, A.; Schiros, T.; Klarr, T.; Mazzoni, A.; Chin, M.; Chiu, Y.-c.; Zheng, W.; Zhang, Q. R.; Ernst, F.; Dadap, J. I.; Tong, X.; Ma, J.; Lou, R.; Wang, S.; Qian, T.; Ding, H.; Osgood, R. M., Jr.; Paley, D. W.; Lindenberg, A. M.; Huang, P. Y.; Pasupathy, A. N.; Dubey, M.; Hone, J.; Balicas, L.

2017-03-01

MoTe$_2$ is an exfoliable transition metal dichalcogenide (TMD) which crystallizes in three symmetries, the semiconducting trigonal-prismatic $2H-$phase, the semimetallic $1T^{\\prime}$ monoclinic phase, and the semimetallic orthorhombic $T_d$ structure. The $2H-$phase displays a band gap of $\\sim 1$ eV making it appealing for flexible and transparent optoelectronics. The $T_d-$phase is predicted to possess unique topological properties which might lead to topologically protected non-dissipative transport channels. Recently, it was argued that it is possible to locally induce phase-transformations in TMDs, through chemical doping, local heating, or electric-field to achieve ohmic contacts or to induce useful functionalities such as electronic phase-change memory elements. The combination of semiconducting and topological elements based upon the same compound, might produce a new generation of high performance, low dissipation optoelectronic elements. Here, we show that it is possible to engineer the phases of MoTe$_2$ through W substitution by unveiling the phase-diagram of the Mo$_{1-x}$W$_x$Te$_2$ solid solution which displays a semiconducting to semimetallic transition as a function of $x$. We find that only $\\sim 8$ \\% of W stabilizes the $T_d-$phase at room temperature. Photoemission spectroscopy, indicates that this phase possesses a Fermi surface akin to that of WTe$_2$.

Synthesis, characterization and cytotoxic activity of substituted benzyl iminoether Pt(II) complexes of the type cis- and trans-[PtCl2{E-N(H)=C(OMe)CH2-C6H4-p-R}2] (R=Me, OMe, F). X-ray structure of trans-[PtCl2{E-N(H)=C(OMe)CH2-C6H4-p-F}2].

PubMed

Mazzega Sbovata, Silvia; Bettio, Frazia; Marzano, Christine; Tassan, Augusto; Mozzon, Mirto; Bertani, Roberta; Benetollo, Franco; Michelin, Rino A

2008-04-01

New substituted benzyl iminoether derivatives of the type cis- and trans-[PtCl(2){E-N(H)C(OMe)CH(2)-C(6)H(4)-p-R}(2)] (R=Me (1a, 2a), OMe (3a, 4a), F (5a, 6a)) have been synthesized and characterized by elemental analyses, FT-IR spectroscopy and NMR techniques. The iminoether ligands are in the E configuration, which is stable in solution and in the solid state, as confirmed by the (1)H NMR data. Complex trans-[PtCl(2){E-N(H)C(OMe)CH(2)-C(6)H(4)-p-F}(2)] (6a) was also characterized by an X-ray diffraction study. Complexes 1a-6a have been tested against a panel of human tumor cell lines in order to evaluate their cytotoxic activity. cis-Isomers were significant more potent than the corresponding trans-isomers against all tumor cell lines tested; moreover, complexes 1a and 5a showed IC(50) values from about 2-fold to 6-fold lower than those exhibited by cisplatin, used as reference platinum anticancer drug.

η6-Cycloparaphenylene transition metal complexes: synthesis, structure, photophysical properties, and application to the selective monofunctionalization of cycloparaphenylenes.

PubMed

Kubota, Natsumi; Segawa, Yasutomo; Itami, Kenichiro

2015-01-28

The synthesis, structure, photophysical properties, and reactivity of cycloparaphenylenes (CPPs) coordinated to group 6 transition metal fragments are described. The η(6)-coordination of [9]CPP or [12]CPP with M(CO)6 (M = Cr, Mo, W) afforded the corresponding [n]CPP-M(CO)3 complexes (n = 9, 12; M = Cr, Mo, W). In the (1)H NMR spectra of these complexes, characteristic upfield-shifted singlet signals corresponding to the four hydrogen atoms attached to the coordinated C6H4 ring of the CPPs were observed at 5.4-5.9 ppm. The complex [9]CPP-Cr(CO)3 could be successfully isolated in spite of its instability. X-ray crystallographic analysis and computational studies of [9]CPP-Cr(CO)3 revealed that chromium-CPP coordination occurs at the convex surface of [9]CPP both in the solid state and in solution. TD-DFT calculations suggested that the emerging high-wavenumber absorption peak upon coordination of [9]CPP to Cr(CO)3 should be assigned to a weak HOMO-LUMO transition. Moreover, by using the complex [9]CPP-Cr(CO)3, a rapid and highly monoselective CPP functionalization has been achieved. The established one-pot method, consisting of complexation, deprotonation, nucleophilic substitution, and decomplexation steps, yielded silyl-, boryl-, and methoxycarbonyl-substituted CPPs in up to 93% yield relative to reacted starting material.

Structural investigation of the A-site vacancy in scheelites and the luminescence behavior of two continuous solid solutions A(1-1.5x)Eu(x)□(0.5x)WO₄ and A(0.64-0.5y)Eu(0.24)Li(y)□(0.12-0.5y)WO₄ (A = Ca, Sr; □ = vacancy).

PubMed

Jiang, Pengfei; Gao, Wenliang; Cong, Rihong; Yang, Tao

2015-04-07

Scheelite compounds with Eu(3+) substitution are well-known red-phosphors. We prepared and performed a detailed structural characterization of A(1-1.5x)Eu(x)□(0.5x)WO4 and A(0.64-0.5y)Eu(0.24)Li(y)□(0.12-0.5y)WO4 (A = Ca, Sr; □ = vacancy) to confirm the A-site vacancy mechanism for charge balance when bivalent A cations were substituted by Eu(3+). All compounds crystallize in I4₁/a with a disordered arrangement of A(2+), Eu(3+), □ at the A-site. The title compounds are all good red phosphors with a high R/O ratio (∼10), indicating that Eu(3+) is located at a significantly distorted cavity. A(1-1.5x)Eu(x)□(0.5x)WO4 shows a saturation phenomenon at a high doping level, x = 0.20. With the incorporation of Li(+), the emission intensity was generally enhanced compared to the Li(+)-free samples, moreover, an increase of the Li(+) content reduces the content of vacancies, resulting in further increase of the luminescence intensity.

Chemical ordering in substituted fluorite oxides: a computational investigation of Ho2Zr2O7 and RE2Th2O7 (RE=Ho, Y, Gd, Nd, La).

PubMed

Solomon, Jonathan M; Shamblin, Jacob; Lang, Maik; Navrotsky, Alexandra; Asta, Mark

2016-12-12

Fluorite-structured oxides find widespread use for applications spanning nuclear energy and waste containment, energy conversion, and sensing. In such applications the host tetravalent cation is often partially substituted by trivalent cations, with an associated formation of charge-compensating oxygen vacancies. The stability and properties of such materials are known to be influenced strongly by chemical ordering of the cations and vacancies, and the nature of such ordering and associated energetics are thus of considerable interest. Here we employ density-functional theory (DFT) calculations to study the structure and energetics of cation and oxygen-vacancy ordering in Ho 2 Zr 2 O 7 . In a recent neutron total scattering study, solid solutions in this system were reported to feature local chemical ordering based on the fluorite-derivative weberite structure. The calculations show a preferred chemical ordering qualitatively consistent with these findings, and yield values for the ordering energy of 9.5 kJ/mol-cation. Similar DFT calculations are applied to additional RE 2 Th 2 O 7 fluorite compounds, spanning a range of values for the ratio of the tetravalent and trivalent (RE) cation radii. The results demonstrate that weberite-type order becomes destabilized with increasing values of this size ratio, consistent with an increasing energetic preference for the tetravalent cations to have higher oxygen coordination.

Chemical ordering in substituted fluorite oxides: a computational investigation of Ho2Zr2O7 and RE2Th2O7 (RE=Ho, Y, Gd, Nd, La)

NASA Astrophysics Data System (ADS)

Solomon, Jonathan M.; Shamblin, Jacob; Lang, Maik; Navrotsky, Alexandra; Asta, Mark

2016-12-01

Fluorite-structured oxides find widespread use for applications spanning nuclear energy and waste containment, energy conversion, and sensing. In such applications the host tetravalent cation is often partially substituted by trivalent cations, with an associated formation of charge-compensating oxygen vacancies. The stability and properties of such materials are known to be influenced strongly by chemical ordering of the cations and vacancies, and the nature of such ordering and associated energetics are thus of considerable interest. Here we employ density-functional theory (DFT) calculations to study the structure and energetics of cation and oxygen-vacancy ordering in Ho2Zr2O7. In a recent neutron total scattering study, solid solutions in this system were reported to feature local chemical ordering based on the fluorite-derivative weberite structure. The calculations show a preferred chemical ordering qualitatively consistent with these findings, and yield values for the ordering energy of 9.5 kJ/mol-cation. Similar DFT calculations are applied to additional RE2Th2O7 fluorite compounds, spanning a range of values for the ratio of the tetravalent and trivalent (RE) cation radii. The results demonstrate that weberite-type order becomes destabilized with increasing values of this size ratio, consistent with an increasing energetic preference for the tetravalent cations to have higher oxygen coordination.

Magnetic and transport properties of the spin-state disordered oxide La0.8Sr0.2Co1-xRhxO3-δ

NASA Astrophysics Data System (ADS)

Shibasaki, Soichiro; Terasaki, Ichiro; Nishibori, Eiji; Sawa, Hiroshi; Lybeck, Jenni; Yamauchi, Hisao; Karppinen, Maarit

2011-03-01

We report measurements and analysis of magnetization, resistivity, and thermopower of polycrystalline samples of the perovskite-type Co/Rh oxide La0.8Sr0.2Co1-xRhxO3-δ. This system constitutes a solid solution for a full range of x, in which the crystal structure changes from rhombohedral to orthorhombic symmetry with increasing Rh content x. The magnetization data reveal that the magnetic ground state immediately changes upon Rh substitution from ferromagnetic to paramagnetic with increasing x near 0.25, which is close to the structural phase boundary. We find that one substituted Rh ion diminishes the saturation moment by 9 μB, which implies that one Rh3+ ion makes a few magnetic Co3+ ions nonmagnetic (the low-spin state) and causes disorder in the spin state and the highest occupied orbital. In this disordered composition (0.05⩽x⩽0.75), we find that the thermopower is anomalously enhanced below 50 K. In particular, the thermopower of x=0.5 is larger by a factor of 10 than those of x=0 and 1, and the temperature coefficient reaches 4 μV/K2, which is as large as that of heavy-fermion materials such as CeRu2Si2.

Solid-solution stability and preferential site-occupancy in (R-R′){sub 2}Fe{sub 14}B compounds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Colin, C. V.; Dempsey, N. M.; Univ. Grenoble Alpes, Inst NEEL, F-38000 Grenoble

The rare-earth (R) uniaxial anisotropy of R{sub 2}Fe{sub 14}B compounds with magnetic R atoms (e.g., Nd or Pr) is at the origin of the exceptional hard magnetic properties achieved in magnets based on these compounds. The uniaxial anisotropy found in Ce{sub 2}Fe{sub 14}B is attributed mainly to the magnetism of Fe. Ce is the most abundant R element and there has been much recent effort to fabricate magnets in which Ce is partially substituted for Nd. In the present neutron study of (R{sub 1−x}Ce{sub x}){sub 2}Fe{sub 14}B (R = La or Nd), Ce is found to enter the R{sub 2}Fe{submore » 14}B phase over the entire composition range. The crystallographic parameters decrease with increasing Ce content and the Ce atoms preferentially occupy the smaller 4f sites. It is concluded that Ce in these (RR′){sub 2}Fe{sub 14}B compounds essentially maintains the intermediate valence character found in Ce{sub 2}Fe{sub 14}B. It is proposed that, in this intermediate valence state, Ce weakly contributes to uniaxial anisotropy, thus making a link with the fact that significant coercivity is preserved in Ce-substituted NdFeB magnets.« less

Research on the synergistic doped effects and the catalysis properties of Cu2+ and Zn2+ co-doped CeO2 solid solutions

NASA Astrophysics Data System (ADS)

Zhang, Guofang; Li, Yiming; Hou, Zhonghui; Xv, Jianyi; Wang, Qingchun; Zhang, Yanghuan

2018-08-01

The Cu2+ and Zn2+ co-doped CeO2-based solid solutions were synthesized via hydrothermal method. The microstructure and the spectra features of the solid solutions were characterized systematically. The XRD results showed that the dopants were incorporated into the CeO2 lattice to form Ce1-xCu0.5xZn0.5xO2 solid solutions when x was lower than 0.14. The cell parameters and the crystalline size decreased linearly, and the lattice strain gradually increased with increasing the doping level. The TEM patterns showed that the particle size in the solid solution was lower than 10 nm which is in accordance with the XRD results. The ICP analysis indicated that the real doped content in the solid solution was close to the nominal proportion. XPS proved that the Ce3+ component was increased by doping. The Raman and PL spectra indicated that the lattice distortion and the oxygen vacancies also increased following the same trend. At the same time, the synergistic effects of two ions co-doped solid solutions were studied by comparing them with that of single ions doped samples. The catalysis effects of Cu2+ and Zn2+ co-doped CeO2-based solid solutions on the hydrogen storage electrochemical and kinetic properties of Mg2Ni alloys were detected. The electrochemistry properties of the Mg2Ni-Ni-5 wt% Ce1-xCu0.5xZn0.5xO2 composites indicated that the doped catalysts could provide better optimizations to improve the maximum discharge capacities and the discharge potentials. On the other hand, the charge transfer abilities on the surface and diffusion rate of H atoms in the bulk of alloys also got improved. The DSC measurements showed that the hydrogen desorption activation of the hydrogenated composites with Ce0.88Cu0.06Zn0.06O2 solid solutions decreased to 77.03 kJ mol-1, while that of the composites with pure CeO2 was 97.62 kJ mol-1. The catalysis effect was enhanced by the doped content increase that means that the catalysis mechanism had close links to the oxygen vacancy concentration and the lattice defects in the solid solutions. On the other hand, the doped Cu2+ and Zn2+ ions could also play an important role in the catalytic process.

Bio-solid-State processes for synthesis of Li-Fe-phosphate.

PubMed

Kim, Hyoung-Bum; Park, Byungno; Lee, Insung; Roh, Yul

2008-10-01

Lithium-Fe-phosphates have become of great interest as storage cathodes for rechargeable Li-batteries because of their high density, environmental friendliness, and safety. The objective of this study was to examine bio-solid-state synthesis of LiFePO4 by microbial processes at room temperature. The microbial reduction of Fe(III)-citrate using an organic carbon, glucose, as an electron donor in the presence of NaHPO4 and lithium that resulted in the formation of Li-substituted iron phosphate. Our studies showed that bacteria enriched from inter-tidal flat sediments, designated as Haejae-1, synthesized Li-substituted iron phosphate. Characterization by X-ray diffraction showed the reduction of Fe(III)-citrate in the presence of NaHPO4 and LiCl2 resulted in the precipitation of Li-substituted vivianite [Li(x)Fe(3-x)(PO4)2 x 8H2O]. SEM-EDX, FTIR, and ESCA analyses showed the chemical composition of the synthesized phases was Li, Fe, P, C, and O. Based on the chemical and physical structure of the mineral, the novel bio-nano-material may be potentially useful to the development of energy storage materials.

Process for recovering pertechnetate ions from an aqueous solution also containing other ions

DOEpatents

Rogers, R.; Horwitz, E.P.; Bond, A.H.

1997-02-18

A solid/liquid process for the separation and recovery of TcO{sub 4}{sup {minus}1} ions from an aqueous solution is disclosed. The solid support comprises separation particles having surface-bonded poly(ethylene glycol) groups; whereas the aqueous solution from which the TcO{sub 4}{sup {minus}1} ions are separated contains a poly(ethylene glycol) liquid/liquid biphase-forming amount of a dissolved salt. A solid/liquid phase admixture of separation particles containing bound TcO{sub 4}{sup {minus}1} ions in such an aqueous solution that is free from MoO{sub 4}{sup {minus}2} ions is also contemplated, as is a chromatography apparatus containing that solid/liquid phase admixture. 15 figs.

Data-driven discovery of energy materials: efficient BaM2Si3O10 : Eu2+ (M = Sc, Lu) phosphors for application in solid state white lighting.

PubMed

Brgoch, Jakoah; Hasz, Kathryn; Denault, Kristin A; Borg, Christopher K H; Mikhailovsky, Alexander A; Seshadri, Ram

2014-01-01

In developing phosphors for application in solid state lighting, it is advantageous to target structures from databases with highly condensed polyhedral networks that produce rigid host compounds. Rigidity limits channels for non-radiative decay that will decrease the luminescence quantum yield. BaM(2)Si(3)O(10) (M = Sc, Lu) follows this design criterion and is studied here as an efficient Eu(2+)-based phosphor. M = Sc(3+) and Lu(3+) compounds with Eu(2+) substitution were prepared and characterized using synchrotron X-ray powder diffraction and photoluminescence spectroscopy. Substitution with Eu(2+) according to Ba(1-x)Eu(x)Sc(2)Si(3)O(10) and Ba(1-x)Eu(x)Lu(2)Si(3)O(10) results in UV-to-blue and UV-to-blue-green phosphors, respectively. Interestingly, substitution with Eu(2+) in the Lu(3+) containing material produces two emission peaks at low temperature and with 365 nm excitation, as allowed by the two substitution sites. The photoluminescence of the Sc(3+) compound is robust at high temperature, decreasing by only 25% of its room temperature intensity at 503 K, while the Lu-analogue suffers a large drop (75%) from its room temperature intensity. The decrease in emission intensity is explained as stemming from charge transfer quenching due to the short distances separating the luminescent centers on the Lu(3+) substitution site. The correlation between structure and optical response in these two compounds indicates that even though the structures are three-dimensionally connected, high symmetry is required to prevent structural distortions that could impact photoluminescence.

Fish meal replacement by plant protein substitution and guar gum addition in trout feed. Part II: Effects on faeces stability and rheology.

PubMed

Brinker, Alexander; Friedrich, Christian

2012-01-01

In the explosively growing aquaculture industry, the challenge of sustainability includes a requirement to produce more fish than are consumed by stock. A promising avenue of research is the substitution of the fish meal in feeds with plant protein. However, there are inherent risks in the development of such feeds, and serious consideration should be given not only to nutritional content, but also to the mechanical quality of resulting faecal wastes. The present study uses a plate on plate rheometer running in different flow modes (creep, oscillation) to assess the rheological properties of wastes resulting from different diets.All faeces were shown to be thixotropic in nature, independent of diet composition. Details of dietary composition influence the consistency and the characteristic stresses at which faecal structure changes from a viscoelastic solid into a viscoelastic liquid. Furthermore, in linking active food components with mechanical properties of chyme faeces, rheological studies may be used to understand and counteract some problematic properties. Substituting 100% of fish meal with plant proteins leads to faeces that rapidly disintegrate into very fine solids which threaten the viability of aquacultural operations. Adding just 0.3% of the rapidly hydrating non-starch polysaccharide, guar gum (GG), significantly increased the viscosity and elastic modulus of the faeces. These mechanical improvements increase the size of the resulting particles and the effectiveness with which they can be removed, thereby leading to optimized water quality. GG addition was sufficiently effective to counter the stability and particle size effects of a 50% substitution of fish meal, but could not mitigate those of a 100% substitution, wherein dissolution effects of an unknown emulsifier are suspected.

Water Assisted Reaction Mechanism of OH- with CCl4 in Aqueous Solution - Hybrid Quantum Mechanical and Molecular Mechanics Investigation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Jie; Yin, Hongyun; Wang, Dunyou

2013-02-20

The OH- (H2O) + CCl4 reaction in aqueous solution was investigated using the combined quantum mechanical and molecular mechanics approach. The reaction mechanism of OH- (H2O) + CCl4 consists of two concerted steps - formation of OH- in the favorable attack conformation via the proton transfer process, and the nucleophilic substitution process in which the newly formed OH- attacks the CCl4. The free energy activation barrier is 38.2 kcal/mol at CCSD(T)/MM level of theory for this reaction, which is about 10.3 kcal/mol higher than that of the direct nucleophilic substitution mechanism of the OH- + CCl4 reaction in aqueous solution.

Screening possible solid electrolytes by calculating the conduction pathways using Bond Valence method

NASA Astrophysics Data System (ADS)

Gao, Jian; Chu, Geng; He, Meng; Zhang, Shu; Xiao, RuiJuan; Li, Hong; Chen, LiQuan

2014-08-01

Inorganic solid electrolytes have distinguished advantages in terms of safety and stability, and are promising to substitute for conventional organic liquid electrolytes. However, low ionic conductivity of typical candidates is the key problem. As connective diffusion path is the prerequisite for high performance, we screen for possible solid electrolytes from the 2004 International Centre for Diffraction Data (ICDD) database by calculating conduction pathways using Bond Valence (BV) method. There are 109846 inorganic crystals in the 2004 ICDD database, and 5295 of them contain lithium. Except for those with toxic, radioactive, rare, or variable valence elements, 1380 materials are candidates for solid electrolytes. The rationality of the BV method is approved by comparing the existing solid electrolytes' conduction pathways we had calculated with those from experiments or first principle calculations. The implication for doping and substitution, two important ways to improve the conductivity, is also discussed. Among them Li2CO3 is selected for a detailed comparison, and the pathway is reproduced well with that based on the density functional studies. To reveal the correlation between connectivity of pathways and conductivity, α/ γ-LiAlO2 and Li2CO3 are investigated by the impedance spectrum as an example, and many experimental and theoretical studies are in process to indicate the relationship between property and structure. The BV method can calculate one material within a few minutes, providing an efficient way to lock onto targets from abundant data, and to investigate the structure-property relationship systematically.

Synthesis and characterization of Eu{sup 3+}-doped CaZrO{sub 3}-based perovskite-type phosphors. Part I: Determination of the Eu{sup 3+} occupied site using the ALCHEMI technique

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sakaida, Satoshi; Shimokawa, Yohei; Asaka, Toru

2015-07-15

Highlights: • Eu{sup 3+}-doped CaZrO{sub 3}-based compounds were synthesized by the solid state reaction. • PL emission intensity at 614 nm was changed by the second dopant cations. • The site substituted by Eu{sup 3+} cations was investigated by using XRD and ALCHEMI technique. • The dominant Eu{sup 3+} substitution site was found as the B site (Zr{sup 4+}) in the CaZrO{sub {sup 3}}. • The dominant Eu{sup 3+} substitution site could be strongly influenced by the co-dopants. - Abstract: Eu{sup 3+}-doped CaZrO{sub 3}, SrZrO{sub 3}, and Mg{sup 2+}- or Sr{sup 2+}-co-doped CaZrO{sub 3} were synthesized by conventional solid statemore » reaction and their photoluminescence (PL) properties were characterized. The Eu{sup 3+}-doped CaZrO{sub 3}-based compounds exhibited characteristic emissions of Eu{sup 3+} (f–f transition). The intensity of the main PL emission peak at 614 nm increased with Mg{sup 2+} co-doping, while it decreased with the amount of co-doped Sr{sup 2+}. The site substituted by Eu{sup 3+} cations in the CaZrO{sub 3}-based compounds was investigated by X-ray diffraction analysis and energy-dispersive X-ray analysis based on the electron channeling effects in transmission electron microscopy. The Eu{sup 3+} cations were determined to occupy mainly the B site (Zr{sup 4+}) in CaZrO{sub 3}. The dominant Eu{sup 3+} substitution site was also strongly influenced by the co-dopant, and the ionic radius of the co-dopant was identified as an important factor that determines the dominant Eu{sup 3+} substitution site.« less

Financial effect of converting ipratropium-albuterol therapy from inhalers to nebulizer treatments at an academic health system.

PubMed

Loborec, Steven M; Johnson, Shawn E; Keating, Ellen A

2016-02-01

The results of a study to assess the financial impact of an automatic formulary substitution of ipratropium-albuterol nebulization solution for ipratropium-albuterol metered-dose inhalers (MDIs) at an academic health system are reported. The study was conducted at a 1242-bed urban academic health system. Data were collected regarding all respiratory medication administrations during a three-month period before the MDI-to-nebulizer substitution (October-December 2012) and the same period of 2013 (after the substitution was implemented). Purchasing data were compared between the two time periods to measure the impact of the formulary substitution on pharmacy department costs, and documented administrations were assessed to evaluate associated changes in respiratory therapist (RT) workload. With 100% prescriber compliance with the formulary substitution, the number of MDI administrations of ipratropium-albuterol declined from 13,667 in October-December 2012 to zero in the same period of 2013. The substitution required expenditures for equipment (vibrating mesh nebulizer technology and patient-specific kits) and RT personnel (one additional RT was hired), but those added costs were substantially outweighed by cost savings resulting from a substantial reduction in overall respiratory drug spending. An automatic substitution of ipratropium-albuterol nebulization solution for MDIs resulted in a three-month savings of $99,359 in drug cost and an extrapolated full-year savings of $397,436. When additional costs associated with the substitution were taken into account, there was an overall savings of $146,806 during the implementation year and a projected savings of $257,936 for each following year. Copyright © 2016 by the American Society of Health-System Pharmacists, Inc. All rights reserved.

High-performance air-stable n-channel organic thin film transistors based on halogenated perylene bisimide semiconductors.

PubMed

Schmidt, Rüdiger; Oh, Joon Hak; Sun, Ya-Sen; Deppisch, Manuela; Krause, Ana-Maria; Radacki, Krzysztof; Braunschweig, Holger; Könemann, Martin; Erk, Peter; Bao, Zhenan; Würthner, Frank

2009-05-06

The syntheses and comprehensive characterization of 14 organic semiconductors based on perylene bisimide (PBI) dyes that are equipped with up to four halogen substituents in the bay area of the perylene core and five different highly fluorinated imide substituents are described. The influence of the substituents on the LUMO level and the solid state packing of PBIs was examined by cyclic voltammetry and single crystal structure analyses of seven PBI derivatives, respectively. Top-contact/bottom-gate organic thin film transistor (OTFT) devices were constructed by vacuum deposition of these PBIs on SiO(2) gate dielectrics that had been pretreated with n-octadecyl triethoxysilane in vapor phase (OTS-V) or solution phase (OTS-S). The electrical characterization of all devices was accomplished in a nitrogen atmosphere as well as in air, and the structural features of thin films were explored by grazing incidence X-ray diffraction (GIXD) and atomic force microscopy (AFM). Several of those PBIs that bear only hydrogen or up to two fluorine substitutents at the concomitantly flat PBI core afforded excellent n-channel transistors, in particular, on OTS-S substrate and even in air (mu > 0.5 cm(2) V(-1) s(-1); I(on)/I(off) > 10(6)). The best OTFTs were obtained for 2,2,3,3,4,4,4-heptafluorobutyl-substituted PBI 1a ("PTCDI-C4F7") on OTS-S with n-channel field effect mobilities consistently >1 cm(2) V(-1) s(-1) and on-to-off current rations of 10(6) in a nitrogen atmosphere and in air. For distorted core-tetrahalogenated (fluorine, chlorine, or bromine) PBIs, less advantageous solid state packing properties were found and high performance OTFTs were obtained from only one tetrachlorinated derivative (2d on OTS-S). The excellent on-to-off current modulation combined with high mobility in air makes these PBIs suitable for a wide range of practical applications.

Flow-batch analysis of clenbuterol based on analyte extraction on molecularly imprinted polymers coupled to an in-system chromogenic reaction. Application to human urine and milk substitute samples.

PubMed

González, Natalia; Grünhut, Marcos; Šrámková, Ivana; Lista, Adriana G; Horstkotte, Burkhard; Solich, Petr; Sklenářová, Hana; Acebal, Carolina C

2018-02-01

A fully automated spectrophotometric method based on flow-batch analysis has been developed for the determination of clenbuterol including an on-line solid phase extraction using a molecularly imprinted polymer (MIP) as the sorbent. The molecularly imprinted solid phase extraction (MISPE) procedure allowed analyte extraction from complex matrices at low concentration levels and with high selectivity towards the analyte. The MISPE procedure was performed using a commercial MIP cartridge that was introduced into a guard column holder and integrated in the analyzer system. Optimized parameters included the volume of the sample, the type and volume of the conditioning and washing solutions, and the type and volume of the eluent. Quantification of clenbuterol was carried out by spectrophotometry after in-system post-elution analyte derivatization based on azo-coupling using N- (1-Naphthyl) ethylenediamine as the coupling agent to yield a red-colored compound with maximum absorbance at 500nm. Both the chromogenic reaction and spectrophotometric detection were performed in a lab-made flow-batch mixing chamber that replaced the cuvette holder of the spectrophotometer. The calibration curve was linear in the 0.075-0.500mgL -1 range with a correlation coefficient of 0.998. The precision of the proposed method was evaluated in terms of the relative standard deviation obtaining 1.1% and 3.0% for intra-day precision and inter-day precision, respectively. The detection limit was 0.021mgL -1 and the sample throughput for the entire process was 3.4h -1 . The proposed method was applied for the determination of CLB in human urine and milk substitute samples obtaining recoveries values within a range of 94.0-100.0%. Copyright © 2017 Elsevier B.V. All rights reserved.

Polymeric Ionic Networks with High Charge Density: Solid-like Electrolytes in Lithium Metal Batteries

DOE PAGES

Zhang, Pengfei; Li, Mingtao; Jiang, Xueguang; ...

2015-11-02

Polymerized ionic networks (PINs) with six ion pairs per repeating unit are synthesized by nucleophilic-substitution-mediated polymerization or radical polymerization of monomers bearing six 1-vinylimidazolium cations. PIN-based solid-like electrolytes show good ionic conductivities (up to 5.32 × 10 -3 S cm -1 at 22 °C), wide electrochemical stability windows (up to 5.6 V), and good interfacial compatibility with the electrodes.

REMOVAL OF URANIUM FROM ORGANIC LIQUIDS

DOEpatents

Vavalides, S.P.

1959-08-25

A process is described for recovering small quantities of uranium from organic liquids such as hydrocarbon oils. halogen-substituted hydrocarbons, and alcohols. The organic liquid is contacted with a comminuted alkaline earth hydroxide, calcium hydroxide particularly, and the resulting uranium-bearing solid is separated from the liquid by filtration. Uranium may then be recovered from the solid by means of dissolution in nitric acid and conventional extraction with an organic solvent such as tributyl phosphate.

Primary Stability of Zirconium vs Titanium Implants: An In Vitro Comparison

DTIC Science & Technology

2015-06-05

Zirconia implant and 4x11.5 Titanium implant placed in artificial bone ( polyurethane foam ) at .08 rotations /sec…………………………………28   viii...measurements as they relate to primary Implant Stability. Artificial Bone made of solid ridged polyurethane foam was used as an alternative test...30 pound per cubic foot solid rigid polyurethane blocks used to substitute human cancellous bone

ZrB 2-HfB 2 solid solutions as electrode materials for hydrogen reaction in acidic and basic solutions

DOE PAGES

Sitler, Steven J.; Raja, Krishnan S.; Charit, Indrajit

2016-11-09

Spark plasma sintered transition metal diborides such as HfB 2, ZrB 2 and their solid solutions were investigated as electrode materials for electrochemical hydrogen evolutions reactions (HER) in 1 M H 2SO 4 and 1 M NaOH electrolytes. HfB 2 and ZrB 2 formed complete solid solutions when mixed in 1:1, 1:4, and 4:1 ratios and they were stable in both electrolytes. The HER kinetics of the diborides were slower in the basic solution than in the acidic solutions. The Tafel slopes in 1 M H 2SO 4 were in the range of 0.15 - 0.18 V/decade except for puremore » HfB 2 which showed a Tafel slope of 0.38 V/decade. In 1 M NaOH the Tafel slopes were in the range of 0.12 - 0.27 V/decade. The composition of Hf xZr 1-xB 2 solid solutions with x = 0.2 - 0.8, influenced the exchange current densities, overpotentials and Tafel slopes of the HER. As a result, the EIS data were fitted with a porous film equivalent circuit model in order to better understand the HER behavior. In addition, modeling calculations, using density functional theory approach, were carried out to estimate the density of states and band structure of the boride solid solutions.« less

Hydroamination reactions of alkynes with ortho-substituted anilines in ball mills: synthesis of benzannulated N-heterocycles by a cascade reaction.

PubMed

Weiße, Maik; Zille, Markus; Jacob, Katharina; Schmidt, Robert; Stolle, Achim

2015-04-20

It was demonstrated that ortho-substituted anilines are prone to undergo hydroamination reactions with diethyl acetylenedicarboxylate in a planetary ball mill. A sequential coupling of the intermolecular hydroamination reaction with intramolecular ring closure was utilized for the syntheses of benzooxazines, quinoxalines, and benzothiazines from readily available building blocks, that is, electrophilic alkynes and anilines with OH, NH, or SH groups in the ortho position. For the heterocycle formation, it was shown that several stress conditions were able to initiate the reaction in the solid state. Processing in a ball mill seemed to be advantageous over comminution with mortar and pestle with respect to process control. In the latter case, significant postreaction modification occurred during solid-state analysis. Cryogenic milling proved to have an adverse effect on the molecular transformation of the reagents. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

New Defective Brannerite-Type Vanadates. I. Synthesis and Study of Mn 1- x- yφ xNa yV 2-2 x-yMo 2 x+yO 6 Solid Solutions

NASA Astrophysics Data System (ADS)

Masłowska, Bogna; Ziółkowski, Jacek

1994-05-01

MnV 2O 6 of the brannerite-type structure (below 540°C) doped with MoO 3 and Na 2O forms isomorphous solid solutions MnNaφ = Mn 1- x-yφ xNa yV 2-2 x-yMo 2 x+ yO 6 (φ cation vacancy in the original Mn position), belonging to the pseudoternary MnV 2O 6-NaVMoO 6-MoO 3 system. Particular cases are MnNa = Mn 1- yNa y V 2- yMo yO 6 ( x = 0), Mnφ = Mn 1- xφ xV 2-2 xMo 2 xO 6 ( y = 0), and Naφ = Na 1- xφ xV 1- xMo 1+ xO 6 ( x + y = 1). MnV 2O 6 and NaVMoO 6 show miscibility in the entire composition range (MnNa). The opposite boundary of MnNaφ passes through the (100 x, 100 y) points (45, 0), (33, 30), and (30, 70). The phase diagram of the pseudobinary MnV 2O 6-NaVMoO 6 system (determined with DTA) shows (i) a narrow double-lens-type solidus-liquidus gap at high values of y , (ii) two peritectic meltings at lower y (yielding the high temperature β-MnNa and Mn 2V 2O 7), and (iii) little area of β-MnNa. Lattice parameters of MnNa (determined with X-ray diffraction) reveal small deviations from Vegard's law. As the ionic radii of both dopants (Na + and Mo 6+) are, respectively, larger than those of mother ions (Mn 2+ and V 5+), the unit cell increases in all directions with rising y along the MnNa series of solid solutions. However, due to the anisotropy of the structure, parameter c is strongly sensitive to Na/Mn substitution, b is ruled by Mo/V, and a is weakly influenced by Mo/V. Close analogy to the behavior of the previously studied MnV 2O 6-LiVMoO 6-MoO 6 system is discussed.

Enhanced red fluorescence in Sr2Si1-xGexO4:Eu3+ phosphors by the substitution of Si by Ge for white light emitting diodes

NASA Astrophysics Data System (ADS)

Huang, Lihui; Xu, Shiqing; Guo, Meiquan; Wang, Chenyue; Hua, Youjie; Zhao, Shilong; Deng, Degang; Wang, Huanping; Jia, Guohua

2012-07-01

Eu3+-doped Sr2Si1-xGexO4 (x=0-1) phosphors have been prepared by the high temperature solid-state reaction method. The luminescent properties of these phosphors were investigated. Red fluorescence of Eu3+ is enhanced gradually in the samples with increasing substitution of Si by Ge upon the excitation of 393 nm light. The intensity is increased by 50% with full substitution of Si by Ge. These results are originated from the structural changes and the phonon energy reduction in the samples due to the substitution of Si by Ge. The CIE chromaticity coordinates of the phosphors vary slightly around (0.62, 0.37) and all are in the red color region. The results indicate that these phosphors could be promising red phosphors for white light emitting diodes.

Distinct molecular structures and hydrogen bond patterns of α,α-diethyl-substituted cyclic imide, lactam, and acetamide derivatives in the crystalline phase

NASA Astrophysics Data System (ADS)

Krivoshein, Arcadius V.; Ordonez, Carlos; Khrustalev, Victor N.; Timofeeva, Tatiana V.

2016-10-01

α,α-Dialkyl- and α-alkyl-α-aryl-substituted cyclic imides, lactams, and acetamides show promising anticonvulsant, anxiolytic, and anesthetic activities. While a number of crystal structures of various α-substituted cyclic imides, lactams, and acetamides were reported, no in-depth comparison of crystal structures and solid-state properties of structurally matched compounds have been carried out so far. In this paper, we report molecular structure and intermolecular interactions of three α,α-diethyl-substituted compounds - 3,3-diethylpyrrolidine-2,5-dione, 3,3-diethylpyrrolidin-2-one, and 2,2-diethylacetamide - in the crystalline phase, as studied using single-crystal X-ray diffraction and IR spectroscopy. We found considerable differences in the patterns of H-bonding and packing of the molecules in crystals. These differences correlate with the compounds' melting points and are of significance to physical pharmacy and formulation development of neuroactive drugs.

Calculation of open and closed system elastic coefficients for multicomponent solids

NASA Astrophysics Data System (ADS)

Mishin, Y.

2015-06-01

Thermodynamic equilibrium in multicomponent solids subject to mechanical stresses is a complex nonlinear problem whose exact solution requires extensive computations. A few decades ago, Larché and Cahn proposed a linearized solution of the mechanochemical equilibrium problem by introducing the concept of open system elastic coefficients [Acta Metall. 21, 1051 (1973), 10.1016/0001-6160(73)90021-7]. Using the Ni-Al solid solution as a model system, we demonstrate that open system elastic coefficients can be readily computed by semigrand canonical Monte Carlo simulations in conjunction with the shape fluctuation approach. Such coefficients can be derived from a single simulation run, together with other thermodynamic properties needed for prediction of compositional fields in solid solutions containing defects. The proposed calculation approach enables streamlined solutions of mechanochemical equilibrium problems in complex alloys. Second order corrections to the linear theory are extended to multicomponent systems.

Local Structure and Short-Range Order in a NiCoCr Solid Solution Alloy

DOE PAGES

Zhang, F. X.; Zhao, Shijun; Jin, Ke; ...

2017-05-19

Multi-element solid solution alloys are intrinsically disordered on the atomic scale, and many of their advanced properties originate from the unique local structural characteristics. We measured the local structure of a NiCoCr solid solution alloy with X-ray/neutron total scattering and extended X-ray absorption fine structure (EXAFS) techniques. The atomic pair distribution function analysis (PDF) did not exhibit distinct structural distortion. But, EXAFS analysis suggested that the Cr atoms are favorably bonded with Ni and Co in the solid solution alloys. This short-range order (SRO) plays a role in the distinct low values of electrical and thermal conductivities in Ni-based solidmore » solution alloys when Cr is incorporated. Both the long-range and local structures of the NiCoCr alloy upon Ni ion irradiation were studied and an irradiation-induced enhancement of SRO was found.« less

Preparation of a deuterated polymer: Simulating to produce a solid tritium radioactive source

NASA Astrophysics Data System (ADS)

Hu, Rui; Kan, Wentao; Xiong, Xiaoling; Wei, Hongyuan

2017-08-01

The preparation of a deuterated polymer was performed in order to simulate the production of the corresponding tritiated polymer as a solid tritium radioactive source. Substitution and addition reaction were used to introduce deuterium into the polymer. Proton nuclear magnetic resonance and FT-IR spectroscopy were used to investigate the extent and location of deuterium in the polymer, indicating an effectively deuterated polymer was produced. The thermal analysis showed that the final polymer product could tolerate the environmental temperature below 125 °C in its application. This research provides a prosperous method to prepare solid tritium radioactive source.

SRB Environment Evaluation and Analysis. Volume 3: ASRB Plume Induced Environments

NASA Technical Reports Server (NTRS)

Bender, R. L.; Brown, J. R.; Reardon, J. E.; Everson, J.; Coons, L. W.; Stuckey, C. I.; Fulton, M. S.

1991-01-01

Contract NAS8-37891 was expanded in late 1989 to initiate analysis of Shuttle plume induced environments as a result of the substitution of the Advanced Solid Rocket Booster (ASRB) for the Redesigned Solid Rocket Booster (RSRB). To support this analysis, REMTECH became involved in subscale and full-scale solid rocket motor test programs which further expanded the scope of work. Later contract modifications included additional tasks to produce initial design cycle environments and to specify development flight instrumentation. Volume 3 of the final report describes these analyses and contains a summary of reports resulting from various studies.

Characterisation of iron inclusion during the formation of calcium sulfoaluminate phase

DOE Office of Scientific and Technical Information (OSTI.GOV)

Idrissi, M., E-mail: mari_idrissi@yahoo.f; Diouri, A.; Damidot, D.

The iron distribution among the sulfoaluminate clinker phases and its ability to enter the calcium sulfoaluminate lattice in solid solution can have a significant influence on manufacturing process and reactivity of calcium sulfoaluminate (CSA) cements. X-ray diffraction (XRD) analysis, Moessbauer spectroscopy, scanning electron microscopy (SEM) equipped with an energy dispersive X-ray analysis system (EDAX) and infrared spectroscopy were used to identify the mineralogical conditions of iron inclusion during the formation of calcium sulfoaluminate (C{sub 4}A{sub 3}S) phase from different mixtures in the CaO-Al{sub 2}O{sub 3}-Fe{sub 2}O{sub 3}-SO{sub 3} system. The mixtures, heated in a laboratory electric oven, contained stoichiometric amountsmore » of reagent grade CaCO{sub 3}, Al{sub 2}O{sub 3}, Fe{sub 2}O{sub 3} and CaSO{sub 4.2}H{sub 2}O for the synthesis of Ca{sub 4}Al{sub (6-2x)}Fe{sub 2x}SO{sub 16}, where x, comprised between 0 and 3, is the mole number of Al{sub 2}O{sub 3} substituted by Fe{sub 2}O{sub 3}. With x increasing from 0 to 1.5, both the iron content of C{sub 4}A{sub 3}S phase and the amounts of side components such as C{sub 2}F and CS increased. For x values included in the range of 1.5-3.0, at temperatures higher than 1200 {sup o}C, melting phenomena were observed and, instead of the C{sub 4}A{sub 3}S solid solution, ferritic phases and anhydrite were formed.« less

Modified structural characteristics and enhanced electrochemical properties of oxygen-deficient Li2MnO3-δ obtained from pristine Li2MnO3

NASA Astrophysics Data System (ADS)

Tan, Xiao; Liu, Rui; Xie, Congxin; Shen, Qiang

2018-01-01

Lithium-rich manganese(IV) oxide Li2MnO3 has hardly any activity as the cathode active substance of lithium-ion batteries (LIBs) but its reversible capacity can be greatly improved by introducing oxygen deficiencies. After the solid-state heat treatment of nanocrystalline Li2MnO3 by sodium borohydride (NaBH4), the resulting Li2MnO3-δ crystallites comparatively acquire distinguishable appearances in color and shape and slight differences in surface composition and lattice structure. As a LIB cathode within the potential range of 2.5-4.7 V, at 20 mA g-1 pristine Li2MnO3 gives the specific discharge capacities of 3.3, 5.0 and 7.4 mAh·g-1 in the 1st, 10th and 100th cycles, while the derivative Li2MnO3-δ delivers the relatively high values of 64.8, 103.8 and 140.2 mAh·g-1 in the 1st, 10th and 120th cycles, respectively. Aside from the similar phenomenon of gradual electrochemical activation, substituting Li2MnO3-δ for Li2MnO3 means the great enhancements of charge-transfer ability and electrochemical performances. Especially, the cationic-anionic redox mechanisms of Li2MnO3 and Li2MnO3-δ are similar to each other, suggesting a possible solution to prepare high-performance xLi2MnO3-δ·(1-x)LiMO2 solid solutions for application purposes.

Persistent Epithelial Defects and Corneal Opacity After Collagen Cross-Linking With Substitution of Dextran (T-500) With Dextran Sulfate in Compounded Topical Riboflavin.

PubMed

Höllhumer, Roland; Watson, Stephanie; Beckingsale, Peter

2017-03-01

Collagen cross-linking (CXL) is a commonly performed procedure to prevent the progression of keratoconus. Riboflavin is an essential part of the procedure, which facilitates both the cross-linking process and protection of intraocular structures. Dextran can be added to riboflavin to create an isotonic solution. This case report highlights the importance of compounding riboflavin with the correct dextran solution. A retrospective case series. Six eyes of 4 male patients with keratoconus aged from 20 to 38 years underwent CXL with substitution of 20% dextran (T-500) with 20% dextran sulfate in a compounded riboflavin 0.1% solution. Postoperatively, persistent corneal epithelial defects, stromal haze, and then scarring occurred. Corneal transplantation was performed for visual rehabilitation but was complicated by graft rejection followed by failure (n = 1 eye), dehiscence (n = 4), cataract (n = 2), post-laser ablation haze (n = 1), and steroid-induced glaucoma (n = 2). The visual outcome was <6/18 in all 6 cases because of irregular astigmatism and stromal haze. Thinning, vascularization, and scarring of the residual host tissue were noted. Substitution of dextran (T-500) with dextran sulfate in riboflavin solutions during CXL results in loss of vision from permanent corneal opacity. Residual host changes may compromise the results of corneal transplantation.

Surface Defects Enhanced Visible Light Photocatalytic H2 Production for Zn-Cd-S Solid Solution.

PubMed

Zhang, Xiaoyan; Zhao, Zhao; Zhang, Wanwan; Zhang, Guoqiang; Qu, Dan; Miao, Xiang; Sun, Shaorui; Sun, Zaicheng

2016-02-10

In order to investigate the defect effect on photocatalytic performance of the visible light photocatalyst, Zn-Cd-S solid solution with surface defects is prepared in the hydrazine hydrate. X-ray photoelectron spectra and photoluminescence results confirm the existence of defects, such as sulfur vacancies, interstitial metal, and Zn and Cd in the low valence state on the top surface of solid solutions. The surface defects can be effectively removed by treating with sulfur vapor. The solid solution with surface defect exhibits a narrower band gap, wider light absorption range, and better photocatalytic perfomance. The optimized solid solution with defects exhibits 571 μmol h(-1) for 50 mg photocatalyst without loading Pt as cocatalyst under visible light irradiation, which is fourfold better than that of sulfur vapor treated samples. The wavelength dependence of photocatalytic activity discloses that the enhancement happens at each wavelength within the whole absorption range. The theoretical calculation shows that the surface defects induce the conduction band minimum and valence band maximum shift downward and upward, respectively. This constructs a type I junction between bulk and surface of solid solution, which promotes the migration of photogenerated charges toward the surface of nanostructure and leads to enhanced photocatalytic activity. Thus a new method to construct highly efficient visible light photocatalysts is opened. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Stabilized antiferroelectricity in xBiScO3-(1-x)NaNbO3 lead-free ceramics with established double hysteresis loops

NASA Astrophysics Data System (ADS)

Gao, Lisheng; Guo, Hanzheng; Zhang, Shujun; Randall, Clive A.

2018-02-01

We previously reported various solid solution systems that demonstrated the stabilized antiferroelectric (P) phases in NaNbO3 through lowering the tolerance factor. However, all those reported modifications were achieved by adding A2+B4+O3 type solid solutions. A lead-free antiferroelectric (AFE) solid solution xBiScO3-(1-x)NaNbO3 was rationalized by adopting the tolerance factor design rule. Specifically, adding BiScO3 was found to effectively stabilize the AFE phase without changing the crystal symmetry of NaNbO3. Microstructure and electron zone axis diffraction patterns from transmission electron microscopy revealed the stabilized AFE (P) phase in this solid solution. Besides, the electric-field-induced polarization with a double-hysteresis loop was observed. The present results pointed out that the strategy could also be applied while adding A3+B3+O3 type solid solutions. In addition, it expanded the compositional design that can be applied to antiferroelectric materials.

Lithium-Based High Energy Density Flow Batteries

NASA Technical Reports Server (NTRS)

Bugga, Ratnakumar V. (Inventor); West, William C. (Inventor); Kindler, Andrew (Inventor); Smart, Marshall C. (Inventor)

2014-01-01

Systems and methods in accordance with embodiments of the invention implement a lithium-based high energy density flow battery. In one embodiment, a lithium-based high energy density flow battery includes a first anodic conductive solution that includes a lithium polyaromatic hydrocarbon complex dissolved in a solvent, a second cathodic conductive solution that includes a cathodic complex dissolved in a solvent, a solid lithium ion conductor disposed so as to separate the first solution from the second solution, such that the first conductive solution, the second conductive solution, and the solid lithium ionic conductor define a circuit, where when the circuit is closed, lithium from the lithium polyaromatic hydrocarbon complex in the first conductive solution dissociates from the lithium polyaromatic hydrocarbon complex, migrates through the solid lithium ionic conductor, and associates with the cathodic complex of the second conductive solution, and a current is generated.

Materials research for passive solar systems: Solid-state phase-change materials

NASA Astrophysics Data System (ADS)

Benson, D. K.; Webb, J. D.; Burrows, R. W.; McFadden, J. D. O.; Christensen, C.

1985-03-01

A set of solid-state phase-change materials is being evaluated for possible use in passive solar thermal energy storage systems. The most promising materials are organic solid solutions of pentaerythritol (C5H12O4), pentaglycerinve (C5H12O3), and neopentyl glycol (C5H12O2). Solid solution mixtures of these compounds can be tailored so that they exhibit solid-to-solid phase transformations at any desired temperature between 25 C and 188 C, and have latent heats of transformation etween 20 and 70 cal/g. Transformation temperatures, specific heats, and latent heats of transformation have been measured for a number of these materials. Limited cyclic experiments suggest that the solid solutions are stable. These phase-change materials exhibit large amounts of undercooling; however, the addition of certain nucleating agents as particulate dispersions in the solid phase-change material greatly reduces this effect. Computer simulations suggest that the use of an optimized solid-state phase-change material in a Trombe wall could provide better performance than a concrete Trombe wall four times thicker and nine times heavier.

Electrolyte for batteries with regenerative solid electrolyte interface

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xiao, Jie; Lu, Dongping; Shao, Yuyan

2017-08-01

An energy storage device comprising: an anode; and a solute-containing electrolyte composition wherein the solute concentration in the electrolyte composition is sufficiently high to form a regenerative solid electrolyte interface layer on a surface of the anode only during charging of the energy storage device, wherein the regenerative layer comprises at least one solute or solvated solute from the electrolyte composition.

Design principles for radiation-resistant solid solutions

NASA Astrophysics Data System (ADS)

Schuler, Thomas; Trinkle, Dallas R.; Bellon, Pascal; Averback, Robert

2017-05-01

We develop a multiscale approach to quantify the increase in the recombined fraction of point defects under irradiation resulting from dilute solute additions to a solid solution. This methodology provides design principles for radiation-resistant materials. Using an existing database of solute diffusivities, we identify Sb as one of the most efficient solutes for this purpose in a Cu matrix. We perform density-functional-theory calculations to obtain binding and migration energies of Sb atoms, vacancies, and self-interstitial atoms in various configurations. The computed data informs the self-consistent mean-field formalism to calculate transport coefficients, allowing us to make quantitative predictions of the recombined fraction of point defects as a function of temperature and irradiation rate using homogeneous rate equations. We identify two different mechanisms according to which solutes lead to an increase in the recombined fraction of point defects; at low temperature, solutes slow down vacancies (kinetic effect), while at high temperature, solutes stabilize vacancies in the solid solution (thermodynamic effect). Extension to other metallic matrices and solutes are discussed.

Experimental replacement of aragonite by hydroxyapatite

NASA Astrophysics Data System (ADS)

Kasioptas, A.; Perdikouri, C.; Geisler, T.; Putnis, A.

2009-04-01

Hydrothermal treatment of aragonite with (NH4)2HPO4 solution has been shown to produce hydroxyapatite (HAP) with an overall identical and thus pre-determined morphology (Kasioptas et al, 2008). The preservation of the morphology is an outcome of the pseudomorphic nature of this particular reaction. We have investigated the mechanism of the replacement of aragonite by HAP using single, natural, inorganic aragonite crystals. Isothermal experiments were carried out with small crystals placed and sealed in autoclaves with (NH4)2HPO4 solution. After the experiments the aragonite crystals are partly replaced by a new phase. X-ray powder diffraction confirmed that the product phase is indeed HAP; however electron microprobe measurements revealed that the HAP is probably non-stoichiometric. Even when completely converted to HAP, scanning electron microscopy showed that the fine-structure of the aragonite has perfectly been retained. It was also observed that the HAP product phase exhibited a high porosity and was separated from the aragonite parent phase by a sharp interface (on the micrometer scale). The replacement of aragonite by HAP in an aqueous solution can be described in terms of a coupled dissolution-reprecipitation mechanism that takes place at an inward moving reaction front (Putnis& Putnis, 2007). The porosity in the HAP product phase allows the solution to reach the reaction interface. In addition, we have performed experiments with (NH4)2HPO4 solutions prepared with H2O enriched with 97 at.% 18O. The solutions were pre-heated separately to equilibrate the oxygen isotopes in the solution. Raman spectroscopy of the HAP product was used to identify the different vibration modes in the PO43-molecule due to the exchange of 16O with 18O atoms. Apart from the main ?1(PO4) band located near 962 cm-1, we observed four new bands near 945, 931, 919 and 908 cm-1. We have attributed the generation of these new bands to four different degrees of 18O atomic substitutions in the PO43- molecule. The bands that show the highest intensity are those corresponding to three and four 18O atoms substituting for 16O in the PO4 molecule. A non-equilibrated phosphate solution was also used in the replacement experiments in order to observe the simultaneous processes of replacement and H218O-P16O4 exchange in solution. Differences in the intensity of the four vibration modes offer kinetic information on the replacement mechanism when compared with kinetic data of the H218O-P16O4 exchange reaction obtained from in situ Raman investigations (Geisler et al., 2008). Geisler T., Kasioptas A., Menneken M., Perdikouri C., Putnis A, Journal of Geochemical Exploration (2008) Kasioptas A., Perdikouri C., Putnis C.V., Putnis A, Mineralogical Magazine 72, 77-80 (2008) Putnis A., Putnis C.V, Journal of Solid State Chemistry 180, 1783-1786 (2007)

Lipid immiscibility and biophysical properties: Molecular order within and among unit cell volumes

USDA-ARS?s Scientific Manuscript database

Saturated and unsaturated fatty acids clearly have a discrete chemical structure in the solid state. In a saturated solution, the solid state and solution state are in chemical equilibrium. The lipid stearic acid packs in unit cell volumes in the liquid state as well as in the solid state. Normal...

Filtration device for active effluents

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guerin, M.; Meunier, G.

1994-12-31

Among the various techniques relating to solid/liquid separations, filtration is currently utilized for treating radioactive effluents. After testing different equipments on various simulated effluents, the Valduc Center has decided to substitute a monoplate filter for a rotative diatomite precoated filter.

Multiferroic properties in NdFeO3-PbTiO3 solid solutions

NASA Astrophysics Data System (ADS)

Kumar, Sunil; Pal, Jaswinder; Kaur, Shubhpreet; Agrawal, P.; Singh, Mandeep; Singh, Anupinder

2018-05-01

The x(NdFeO3) - 1-x(PbTiO3) where x = 0.2 solid solution was prepared using solid state reaction route. The X-ray diffraction (XRD) data reveals the single phase formation. The microstructure shows grain growth with lesser porosity. The energy dispersive analysis confirms the presence of elements in stochiometric proportion. The polarization vs. Electric field loop estabilished a ferroelectric type behavior but lossy in nature. This lossy nature may be due to the presence of large leakage current in solid solution. The Magnetization vs. Magnetic field plot exhibits a unsaturated hysteriss loop indicates that the sample is not purely ferromagnetic.

Study of low-temperature active rare-earth oxide catalysts for automotive exhaust clean-up.

DOT National Transportation Integrated Search

2014-02-01

We report a facile onepot synthesis of CexZr1-xO2 (0x1) solid solution nanocrystals using hydrothermal reactions. A direct formation of oxide solid solutions in aqueous solution under pressure at low temperatures was clearly revealed by X-ra...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xie, Miao; Mohammadi, Reza; Turner, Christopher L.

In this paper, we explore the hardening mechanisms in WB4-based solid solutions upon addition of Ta, Mn, and Cr using in situ radial X-ray diffraction techniques under nonhydrostatic pressure. By examining the lattice-supported differential strain, we provide insights into the mechanism for hardness increase in binary solid solutions at low dopant concentrations. Speculations on the combined effects of electronic structure and atomic size in ternary WB 4 solid solutions containing Ta with Mn or Cr are also included to understand the extremely high hardness of these materials.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xie, Miao; Turner, Christopher L.; Mohammadi, Reza

In this work, we explore the hardening mechanisms in WB{sub 4}-based solid solutions upon addition of Ta, Mn, and Cr using in situ radial X-ray diffraction techniques under non-hydrostatic pressure. By examining the lattice-supported differential strain, we provide insights into the mechanism for hardness increase in binary solid solutions at low dopant concentrations. Speculations on the combined effects of electronic structure and atomic size in ternary WB{sub 4} solid solutions containing Ta with Mn or Cr are also included to understand the extremely high hardness of these materials.

Solid-solution thermodynamics in Al-Li alloys

NASA Astrophysics Data System (ADS)

Alekseev, A. A.; Lukina, E. A.

2016-05-01

The relative equilibrium concentrations of lithium atoms distributed over different electron-structural states has been estimated. The possibility of the existence of various nonequilibrium electron-structural states of Li atoms in the solid solution in Al has been substantiated thermodynamically. Upon the decomposition of the supersaturated solid solution, the supersaturation on three electron-structural states of Li atoms that arises upon the quenching of the alloy can lead to the formation of lithium-containing phases in which the lithium atoms enter in one electron-structural state.

Concentration Dependent Physical Properties of Ge1-xSnx Solid Solution

NASA Astrophysics Data System (ADS)

Jivani, A. R.; Jani, A. R.

2011-12-01

Our own proposed potential is used to investigate few physical properties like total energy, bulk modulus, pressure derivative of bulk modulus, elastic constants, pressure derivative of elastic constants, Poisson's ratio and Young's modulus of Ge1-xSnx solid solution with x is atomic concentration of α-Sn. The potential combines linear plus quadratic types of electron-ion interaction. First time screening function proposed by Sarkar et al is used to investigate the properties of the Ge-Sn solid solution system.

New anatase-type Til-2xNbxAlxO2 solid solution nanoparticles: direct formation, phase stability, and photocatalytic performance.

PubMed

Hirano, Masanori; Ito, Takaharu

2006-12-01

New anatase-type titania solid solutions co-doped with niobium and aluminum (Til-2xNbxAIlxO2 (X = 0 -0.20)) were synthesized as nanoparticles from precursor solutions of TiOSO4, NbCl5, and Al(NO3)3 under mild hydrothermal conditions at 180 degrees C for 5 h using the hydrolysis of urea. The lattice parameters a0 and c0 of anatase slightly and gradually increased, when the content of niobium and aluminum increased from X = 0 to 0.20. The crystallite size of anatase increased from 12 to 28 nm with increasing the value of X from 0 to 0.20. Their photocatalytic activity and adsorptivity were evaluated separately by the measurement of the concentration of methylene blue (MB) remained in the solution in the dark or under UV-light irradiation. The adsorptivity of TiO2 was improved by the formation of anatase-type Til-2xNbxAlxO2 solid solutions. The photocatalytic activity of anatase-type Til-2xNbxAlxO2 solid solutions was superior to that of commercially available anatase-type pure TiO2 (ST-01) and anatase-type pure TiO2 hydrothermally prepared. The new anatase phase of Til-2xNbxAlxO2 (X = 0-0.20) solid solutions existed stably up to 850 0C during heat treatment in air. In comparison with hydrothermal pure TiO2, the starting temperature of anatase-to-rutile phase transformation was delayed by the formation of Ti1-2xNbxAlxO, (X = 0-0.20) solid solutions, although its completing temperature was accelerated.

Site specific ligand substitution in cubane-type Mo3FeS(4)(4+) clusters: kinetics and mechanism of reaction and isolation of mixed ligand Cl/SPh complexes.

PubMed

Algarra, Andrés G; Basallote, Manuel G; Fernandez-Trujillo, M J; Llusar, Rosa; Pino-Chamorro, Jose A; Sorribes, Ivan; Vicent, Cristian

2010-04-21

The synthesis, crystal structure and solution characterization of the cubane-type [Mo(3)(FeCl)S(4)(dmpe)(3)Cl(3)] (1) (dmpe = 1,2-bis(dimethylphophane-ethane)) cluster are reported and the ligand substitution processes of chloride by thiophenolate investigated. The kinetics and the intimate mechanism of these substitutions reveal that compound 1 undergoes a number of Fe and Mo site specific ligand substitution reactions in acetonitrile solutions. In particular, PhS(-) coordination at the tetrahedral Fe site proceeds in a single resolved kinetic step whereas such substitutions at the Mo sites proceed more slowly. The effect of the presence of acids in the reaction media is also investigated and reveals that an acid excess hinders substitution reactions both at the Fe and Mo sites; however, an acid-promoted solvolysis of the Fe-Cl bonds is observed. Electrospray ionization (ESI) and tandem (ESI-MS/MS) mass spectrometry allow the identification of all the reaction intermediates proposed on the basis of stopped-flow measurements. The distinctive site specific reactivity made it possible to isolate two new clusters of the Mo(3)FeS(4)(4+) family featuring mixed chlorine/thiophenolate ligands, namely Mo(3)S(4)(FeSPh)(dmpe)(3)Cl(3) (2) and [Mo(3)S(4)(FeSPh)(dmpe)(3)(SPh)(3)] (3). A detailed computational study has also been carried out to understand the details of the mechanism of substitution at the M-Cl (M = Mo and Fe) bonds as well as the solvolysis at the Fe-Cl sites, with particular emphasis on the role of acids on the substitution process. The results of the calculations are in agreement with the experimental observations, thus justifying the non-existence of an accelerating effect of acids on the thiophenolate substitution reaction, which differs from previous proposals for the Fe(4)S(4) and MoFe(3)S(4) clusters and some related compounds.

Major- and minor-metal composition of three distinct solid material fractions associated with Juan de Fuca hydrothermal fluids (northeast Pacific), and calculation of dilution fluid samples

USGS Publications Warehouse

Hinkley, T.K.; Seeley, J.L.; Tatsumoto, M.

1988-01-01

Three distinct types of solid material are associated with each sample of the hydrothermal fluid that was collected from the vents of the Southern Juan de Fuca Ridge. The solid materials appear to be representative of deposits on ocean floors near mid-ocean ridges, and interpretation of the chemistry of the hydrothermal solutions requires understanding of them. Sr isotopic evidence indicates that at least two and probably all three of these solid materials were removed from the solution with which they are associated, by precipitation or adsorption. This occurred after the "pure" hydrothermal fluid was diluted and thoroughly mixed with ambient seawater. The three types of solid materials, are, respectively, a coarse Zn- and Fe-rich material with small amounts of Na and Ca; a finer material also rich in Zn and Fe, but with alkali and alkaline-earth metals; and a scum composed of Ba or Zn, with either considerable Fe or Si, and Sr. Mineral identification is uncertain because of uncertain anion composition. Only in the cases of Ba and Zn were metal masses greater in solid materials than in the associated fluids. For all other metals measured, masses in fluids dwarf those in solids. The fluids themselves contain greater concentrations of all metals measured, except Mg, than seawater. We discuss in detail the relative merits of two methods of determining the mixing proportions of "pure" hydrothermal solution and seawater in the fluids, one based on Sr isotopes, and another previously used method based on Mg concentrations. Comparison of solute concentrations in the several samples shows that degree of dilution of "pure" hydrothermal solutions by seawater, and amounts of original solutes that were removed from it as solid materials, are not related. There is no clear evidence that appreciable amounts of solid materials were not conserved (lost) either during or prior to sample collection. ?? 1988.

Dielectric and AC conductivity studies of Nd substituted 0.8BaTiO{sub 3}-0.2(Bi{sub 0.5(1-x)}Nd{sub 0.5x}K{sub 0.5})TiO{sub 3} lead free ceramics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramesh, M. N. V.; Ramesh, K. V., E-mail: kv-ramesh5@yahoo.co.in

2016-05-23

0.8BaTiO{sub 3} – 0.2(Bi{sub 0.5(1-x)}Nd{sub 0.5x}K{sub 0.5})TiO{sub 3} (0.01 ≤ x ≤ 0.06) lead free ceramic materials have been prepared by solid state reaction method and followed by high energy ball milling process. X-ray diffraction studies confirm the tetragonal structure of the materials at room temperature. Lattice parameters and density are decreasing with increase of Nd substitution. Microstructure studies were done by using Scanning electron microscope and it found that grain size is decreasing with increase of Nd substitution. Temperature and frequency dependent dielectric studies reveal relaxor behaviour of the materials. Dielectric constant, dielectric loss and Curie temperature are decreasingmore » with Nd substitution. Maximum Curie temperature of 195°C was observed at 1 MHz for x=0.01 Nd substituted sample. Degree of diffuseness was calculated from the modified Curie-Weiss law and it is increasing with Nd substitution. AC conductivity is increasing with increase of Nd substitution and observed maximum activation energy of 0.52 eV for x=0.02 Nd substituted sample.« less

Effects of replacing dietary starch with neutral detergent-soluble fibre on ruminal fermentation, microbial synthesis and populations of ruminal cellulolytic bacteria using the rumen simulation technique (RUSITEC).

PubMed

Zhao, X H; Liu, C J; Liu, Y; Li, C Y; Yao, J H

2013-12-01

A rumen simulation technique (RUSITEC) apparatus with eight 800 ml fermenters was used to investigate the effects of replacing dietary starch with neutral detergent-soluble fibre (NDSF) by inclusion of sugar beet pulp in diets on ruminal fermentation, microbial synthesis and populations of ruminal cellulolytic bacteria. Experimental diets contained 12.7, 16.4, 20.1 or 23.8% NDSF substituted for starch on a dry matter basis. The experiment was conducted over two independent 15-day incubation periods with the last 8 days used for data collection. There was a tendency that 16.4% NDSF in the diet increased the apparent disappearance of organic matter (OM) and neutral detergent fibre (NDF). Increasing dietary NDSF level increased carboxymethylcellulase and xylanase activity in the solid fraction and apparent disappearance of acid detergent fibre (ADF) but reduced the 16S rDNA copy numbers of Ruminococcus albus in both liquid and solid fractions and R. flavefaciens in the solid fraction. The apparent disappearance of dietary nitrogen (N) was reduced by 29.6% with increased dietary NDSF. Substituting NDSF for starch appeared to increase the ratios of acetate/propionate and methane/volatile fatty acids (VFA) (mol/mol). Replacing dietary starch with NDSF reduced the daily production of ammonia-N and increased the growth of the solid-associated microbial pellets (SAM). Total microbial N flow and efficiency of microbial synthesis (EMS), expressed as g microbial N/kg OM fermented, tended to increase with increased dietary NDSF, but the numerical increase did not continue as dietary NDSF exceeded 20.1% of diet DM. Results suggested that substituting NDSF for starch up to 16.4% of diet DM increased digestion of nutrients (except for N) and microbial synthesis, and further increases (from 16.4% to 23.8%) in dietary NDSF did not repress microbial synthesis but did significantly reduce digestion of dietary N. © 2012 Blackwell Verlag GmbH.

Effect of Mn and Ti substitution on the reflection loss characteristic of Ba{sub 0.6}Sr{sub 0.4}Fe{sub 11-z}MnTi{sub z}O{sub 19} (z = 0, 1, 2 and 3)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gunanto, Y. E., E-mail: yohanes.gunanto@uph.edu; Cahyadi, L., E-mail: lina.cahyadi@uph.edu; Adi, W. Ari, E-mail: dwisnuaa@batan.go.id

2016-04-19

The synthesis and characterization of composition Ba{sub 0.6}Sr{sub 0.4}Fe{sub 11-z}MnTi{sub z}O{sub 19} (z = 0; 1; 2 and 3) compound by solid state reaction using mechanical milling have been performed. The raw materials were BaCO{sub 3}, SrCO{sub 3}, Fe{sub 2}O{sub 3}, MnCO{sub 3}, and TiO{sub 2}. The mixed powder was compacted and sintered at 1000°C for 5 hours. X-ray diffraction studies indicate expansion of hexagonal unit cell and compression of atomic density with substitution of Mn{sup 2+} and Ti{sup 4+} ions. Effect of substitution upon magnetic properties revealed that total magnetization, remanence, and coercivity changed with substitution due to preferentialmore » site occupancy of substituted Mn{sup 2+} and Ti{sup 4+} ions. Since the coercivity and total magnetization may be controlled by substitution while maintaining resistive properties, this material is useful for microwave absorber.« less

Calcium release in skinned muscle fibres of the toad by transverse tubule depolarization or by direct stimulation.

PubMed

Lamb, G D; Stephenson, D G

1990-04-01

1. Skeletal muscle fibres from the toad were mechanically skinned under paraffin oil and then bathed in a potassium HDTA solution (HDTA: hexamethylenediamine-tetraacetate) which mimicked the ionic composition of the myoplasm. 2. Rapid transient contractions could be triggered by substitution of K+ with Na+ (with no change of anion), which should have virtually no direct effect on the electrical polarization of the sarcoplasmic reticulum (SR) membrane. Up to thirty or more contractions could be evoked by repeated substitutions if there was sufficient 'repriming' time (about 30 s) between them; these rapid contractions were analagous to potassium contractures in intact fibres. 3. When the SR was not heavily loaded, substitution of potassium HDTA with choline chloride also produced a rapid, brief contraction. 4. All treatments designed to 'inactivate' the voltage sensor in the T-system invariably abolished the rapid contractions. Thus, rapid contractions were absent if (i) the T-system was permanently depolarized by pre-soaking the muscle in a high potassium solution with ouabain before skinning, (ii) a fibre was split rather than skinned, (iii) the T-system was temporarily depolarized by Na+ substitution immediately before choline chloride substitution, or vice versa, (iv) a skinned fibre was briefly exposed to saponin (50 micrograms/ml) to selectively disrupt the T-system membrane or (v) the muscle was pre-soaked in a solution with 1 mM-EGTA and no Ca2+ or Mg2+ before skinning. In contrast to (v), if 10 mM-Mg2+ was present in the EGTA solution before skinning, rapid contractions could be elicited, presumably because the presence of Mg2+ prevented the inactivation of the T-system voltage sensor in low [Ca2+]. 5. These results unequivocally demonstrate that (a) the T-system reseals and repolarizes after mechanical skinning under oil and (b) the fast contractions are produced by activation of the voltage sensor in the T-system. 6. When the SR had been heavily loaded, choline chloride substitution (but not Na+ substitution) could also induce an unphysiological, slow contraction ('second component'). In total contrast to the fast contraction, this slow component was unaffected by any of the treatments (i-v) above, indicating that it did not depend on activation of the voltage sensor in the T-system but resulted from a direct action of choline chloride on the SR.(ABSTRACT TRUNCATED AT 400 WORDS)

Calcium release in skinned muscle fibres of the toad by transverse tubule depolarization or by direct stimulation.

PubMed Central

Lamb, G D; Stephenson, D G

1990-01-01

1. Skeletal muscle fibres from the toad were mechanically skinned under paraffin oil and then bathed in a potassium HDTA solution (HDTA: hexamethylenediamine-tetraacetate) which mimicked the ionic composition of the myoplasm. 2. Rapid transient contractions could be triggered by substitution of K+ with Na+ (with no change of anion), which should have virtually no direct effect on the electrical polarization of the sarcoplasmic reticulum (SR) membrane. Up to thirty or more contractions could be evoked by repeated substitutions if there was sufficient 'repriming' time (about 30 s) between them; these rapid contractions were analagous to potassium contractures in intact fibres. 3. When the SR was not heavily loaded, substitution of potassium HDTA with choline chloride also produced a rapid, brief contraction. 4. All treatments designed to 'inactivate' the voltage sensor in the T-system invariably abolished the rapid contractions. Thus, rapid contractions were absent if (i) the T-system was permanently depolarized by pre-soaking the muscle in a high potassium solution with ouabain before skinning, (ii) a fibre was split rather than skinned, (iii) the T-system was temporarily depolarized by Na+ substitution immediately before choline chloride substitution, or vice versa, (iv) a skinned fibre was briefly exposed to saponin (50 micrograms/ml) to selectively disrupt the T-system membrane or (v) the muscle was pre-soaked in a solution with 1 mM-EGTA and no Ca2+ or Mg2+ before skinning. In contrast to (v), if 10 mM-Mg2+ was present in the EGTA solution before skinning, rapid contractions could be elicited, presumably because the presence of Mg2+ prevented the inactivation of the T-system voltage sensor in low [Ca2+]. 5. These results unequivocally demonstrate that (a) the T-system reseals and repolarizes after mechanical skinning under oil and (b) the fast contractions are produced by activation of the voltage sensor in the T-system. 6. When the SR had been heavily loaded, choline chloride substitution (but not Na+ substitution) could also induce an unphysiological, slow contraction ('second component'). In total contrast to the fast contraction, this slow component was unaffected by any of the treatments (i-v) above, indicating that it did not depend on activation of the voltage sensor in the T-system but resulted from a direct action of choline chloride on the SR.(ABSTRACT TRUNCATED AT 400 WORDS) PMID:1696987

Waste-free synthesis of condensed heterocyclic compounds by rhodium-catalyzed oxidative coupling of substituted arene or heteroarene carboxylic acids with alkynes.

PubMed

Shimizu, Masaki; Hirano, Koji; Satoh, Tetsuya; Miura, Masahiro

2009-05-01

The direct oxidative coupling of 2-amino- and 2-hydroxybenzoic acids with internal alkynes proceeds efficiently in the presence of a rhodium/copper catalyst system under air to afford the corresponding 8-substituted isocoumarin derivatives, some of which exhibit solid-state fluorescence. Depending on conditions, 4-ethenylcarbazoles can be synthesized selectively from 2-(arylamino)benzoic acids. The oxidative coupling reactions of heteroarene carboxylic acids as well as aromatic diacids with an alkyne are also described.

Method of preparing meso-haloalkylporphyrins

DOEpatents

Wijesekera, Tilak; Lyons, James E.; Ellis, Jr., Paul E.; Bhinde, Manoj V.

1998-01-01

Transition metal complexes of meso-haloalkylporphyrins, wherein the haloalkyl groups contain 2 to 8 carbon atoms have been found to be highly effective catalysts for oxidation of alkanes and for the decomposition of hydroperoxides. Also disclosed is a process for the preparation of meso-halocarbyl-porphyrins which comprises contacting a halocarbyl dipyrromethane with a halocarbyl-substituted aldehyde in the presence of an acid granular solid catalyst. Also disclosed is a process for the preparation of meso-halocarbyl-porphyrins which comprises contacting a halocarbyl dipyrromethane with a halocarbyl-substituted aldehyde in the presence of an acid granular solic catalyst.

Effect of varying Ga content in ZnO:GaN solid solution synthesized by solution combustion technique for photocatalytic applications

NASA Astrophysics Data System (ADS)

Menon, Sumithra Sivadas; Janani, R.; Baskar, K.; Gupta, Bhavana; Singh, Shubra

2017-05-01

ZnO:GaN (oxy)nitride solid solution has been established as the most efficient non-oxide photocatalyst for water splitting under visible irradiation with one step photoexcitation and also boasts a band gap tunability from 2.8 eV to 2.5 eV[1]. The solid solution of GaN in ZnO is formed by the intersubstitution of few of Zn/O ions by Ga/N ions, and this results in the introduction of new defect levels above the valence band which narrows the effective band gap enabling activity under visible region of spectra. In this work, we report the synthesis of ZnO:GaN solid solution by a solution combustion technique where metal nitrates and urea are used as precursors. The Zn/Ga ratio was varied from 16 to 1 in the precursors. The as synthesized samples were characterized as phase pure by X-ray diffraction, where the wurtzite structure was retained up to Zn/Ga ratio of 5. The Diffuse reflectance spectroscopy studies revealed that as the Ga content in the solid solution increases there is a reduction in band gap, from 2.9 eV to 2.4 eV. The reduced band gap of the samples facilitates its photocatalytic activity under visible region of the spectra as evaluated by photoelectrochemical measurements.

Method of fabricating lipid bilayer membranes on solid supports

NASA Technical Reports Server (NTRS)

Cho, Nam-Joon (Inventor); Frank, Curtis W. (Inventor); Glenn, Jeffrey S. (Inventor); Cheong, Kwang Ho (Inventor)

2012-01-01

The present invention provides a method of producing a planar lipid bilayer on a solid support. With this method, a solution of lipid vesicles is first deposited on the solid support. Next, the lipid vesicles are destabilized by adding an amphipathic peptide solution to the lipid vesicle solution. This destabilization leads to production of a planar lipid bilayer on the solid support. The present invention also provides a supported planar lipid bilayer, where the planar lipid bilayer is made of naturally occurring lipids and the solid support is made of unmodified gold or titanium oxide. Preferably, the supported planar lipid bilayer is continuous. The planar lipid bilayer may be made of any naturally occurring lipid or mixture of lipids, including, but not limited to phosphatidylcholine, phosphatidylethanolamine, phosphatidylserine, phosphatidylinsitol, cardiolipin, cholesterol, and sphingomyelin.

Polybenzimidazole compounds, polymeric media, and methods of post-polymerization modifications

DOEpatents

Klaehn, John R [Idaho Falls, ID; Peterson, Eric S [Idaho Falls, ID; Wertsching, Alan K [Idaho Falls, ID; Orme, Christopher J [Shelley, ID; Luther, Thomas A [Idaho Falls, ID; Jones, Michael G [Pocatello, ID

2007-08-21

A PBI compound includes imidazole nitrogens at least a portion of which are substituted with an organic-inorganic hybrid moiety. At least 85% of the imidazole nitrogens may be substituted. The organic-inorganic hybrid moiety may be an organosilane moiety, for example, (R)Me.sub.2SiCH.sub.2-- where R is selected from among methyl, phenyl, vinyl, and allyl. The PBI compound may exhibit similar thermal properties in comparison to the unsubstituted PBI. The PBI compound may exhibit a solubility in an organic solvent greater than the solubility of the unsubstituted PBI. The PBI compound may be included in separatory media. A substituted PBI synthesis method may include providing a parent PBI in a less than 5 wt % solvent solution. Substituting may occur at about room temperature and/or at about atmospheric pressure. Substituting may use at least 5 equivalents in relation to the imidazole nitrogens to be substituted or, preferably, about 15.

Polybenzimidazole compounds

DOEpatents

Klaehn, John R.; Peterson, Eric S.; Wertsching, Alan K.; Orme, Christopher J.; Luther, Thomas A.; Jones, Michael G.

2010-08-10

A PBI compound that includes imidazole nitrogens, at least a portion of which are substituted with an organic-inorganic hybrid moiety. At least 85% of the imidazole nitrogens may be substituted. The organic-inorganic hybrid moiety may be an organosilane moiety, for example, (R)Me.sub.2SiCH.sub.2--, where R is selected from among methyl, phenyl, vinyl, and allyl. The PBI compound may exhibit similar thermal properties in comparison to the unsubstituted PBI. The PBI compound may exhibit a solubility in an organic solvent greater than the solubility of the unsubstituted PBI. The PBI compound may be included in separatory media. A substituted PBI synthesis method may include providing a parent PBI in a less than 5 wt % solvent solution. Substituting may occur at about room temperature and/or at about atmospheric pressure. Substituting may use at least five equivalents in relation to the imidazole nitrogens to be substituted or, preferably, about fifteen equivalents.

A new molecular evolution model for limited insertion independent of substitution.

PubMed

Lèbre, Sophie; Michel, Christian J

2013-10-01

We recently introduced a new molecular evolution model called the IDIS model for Insertion Deletion Independent of Substitution [13,14]. In the IDIS model, the three independent processes of substitution, insertion and deletion of residues have constant rates. In order to control the genome expansion during evolution, we generalize here the IDIS model by introducing an insertion rate which decreases when the sequence grows and tends to 0 for a maximum sequence length nmax. This new model, called LIIS for Limited Insertion Independent of Substitution, defines a matrix differential equation satisfied by a vector P(t) describing the sequence content in each residue at evolution time t. An analytical solution is obtained for any diagonalizable substitution matrix M. Thus, the LIIS model gives an expression of the sequence content vector P(t) in each residue under evolution time t as a function of the eigenvalues and the eigenvectors of matrix M, the residue insertion rate vector R, the total insertion rate r, the initial and maximum sequence lengths n0 and nmax, respectively, and the sequence content vector P(t0) at initial time t0. The derivation of the analytical solution is much more technical, compared to the IDIS model, as it involves Gauss hypergeometric functions. Several propositions of the LIIS model are derived: proof that the IDIS model is a particular case of the LIIS model when the maximum sequence length nmax tends to infinity, fixed point, time scale, time step and time inversion. Using a relation between the sequence length l and the evolution time t, an expression of the LIIS model as a function of the sequence length l=n(t) is obtained. Formulas for 'insertion only', i.e. when the substitution rates are all equal to 0, are derived at evolution time t and sequence length l. Analytical solutions of the LIIS model are explicitly derived, as a function of either evolution time t or sequence length l, for two classical substitution matrices: the 3-parameter symmetric substitution matrix [12] (LIIS-SYM3) and the HKY asymmetric substitution matrix[9] (LIIS-HKY). An evaluation of the LIIS model (precisely, LIIS-HKY) based on four statistical analyses of the GC content in complete genomes of four prokaryotic taxonomic groups, namely Chlamydiae, Crenarchaeota, Spirochaetes and Thermotogae, shows the expected improvement from the theory of the LIIS model compared to the IDIS model. Copyright © 2013 Elsevier Inc. All rights reserved.

Hydroxypyridonate chelating agents and synthesis thereof

DOEpatents

Raymond, K.N.; Scarrow, R.C.; White, D.L.

1985-11-12

Chelating agents having 1-hydroxy-2-pyridinone (HOPO) and related moieties incorporated within their structures, including polydentate HOPO-substituted polyamines such as spermidine and spermine, and HOPO-substituted desferrioxamine. The chelating agents are useful in selectively removing certain cations from solution, and are particularly useful as ferric ion and actinide chelators. Novel syntheses of the chelating agents are provided. 4 tabs.

Planet Patrol. An Educational Unit on Solid Waste Solutions for Grades 4-6.

ERIC Educational Resources Information Center

Shively, Patti J.; And Others

This educational unit on solid waste solutions is intended to convey to students an understanding of the four methods of solid waste handling, in priority order, as recommended by the Environmental Protection Agency: (1) reduction in the volume of waste produced; (2) recycling and composting; (3) waste combustion, i.e., incineration of waste; and…

Polarization-sensitive nanowire photodetectors based on solution-synthesized CdSe quantum-wire solids.

PubMed

Singh, Amol; Li, Xiangyang; Protasenko, Vladimir; Galantai, Gabor; Kuno, Masaru; Xing, Huili Grace; Jena, Debdeep

2007-10-01

Polarization-sensitive photodetectors are demonstrated using solution-synthesized CdSe nanowire (NW) solids. Photocurrent action spectra taken with a tunable white light source match the solution linear absorption spectra of the NWs, showing that the NW network is responsible for the device photoconductivity. Temperature-dependent transport measurements reveal that carriers responsible for the dark current through the nanowire solids are thermally excited across CdSe band gap. The NWs are aligned using dielectrophoresis between prepatterned electrodes using conventional optical photolithography. The photocurrent through the NW solid is found to be polarization-sensitive, consistent with complementary absorption (emission) measurements of both single wires and their ensembles. The range of solution-processed semiconducting NW materials, their facile synthesis, ease of device fabrication, and compatibility with a variety of substrates make them attractive for potential nanoscale polarization-sensitive photodetectors.

The solid-solution region for the langasite-type Ca3TaGa3Si2O14 crystal as determined by a lever rule

NASA Astrophysics Data System (ADS)

Zhao, Hengyu; Uda, Satoshi; Maeda, Kensaku; Nozawa, Jun; Koizumi, Haruhiko; Fujiwara, Kozo

2015-04-01

A lever rule was applied to data concerning the compositions and proportions of secondary phases coexisting with a Ca3TaGa3Si2O14 (CTGS) matrix to determine the boundary compositions of the solid-solution region for CTGS at 1320 °C, as a means of ascertaining the solid-solution for the langasite-type phase in the quaternary CaO-Ta2O5-Ga2O3-SiO2 system. The compositions and proportions of secondary phases were assessed by electron probe micro-analysis as well as through back-scattered electron images. The experimental results showed that the narrow solid-solution region for CTGS is located in a Ta-poor, Ga-poor and Si-rich region relative to its stoichiometric composition.

Dynamics of Re(2,2'-bipyridine)(CO)3Cl MLCT formation and decay after picosecond pulsed X-ray excitation and femtosecond UV excitation.

PubMed

Zhao, Liyan; Odaka, Hideho; Ono, Hiroshi; Kajimoto, Shinji; Hatanaka, Koji; Hobley, Jonathan; Fukumura, Hiroshi

2005-01-01

The dynamics of Re(2,2'-bipyridine)(CO)3Cl MLCT state formation and decay were determined after femtosecond UV laser excitation and picosecond pulsed X-ray excitation, in an N,N-dimethylformamide (DMF) solution as well as in its solid form. At room temperature, after UV excitation, this MLCT excited state emits both in DMF solution and in the solid form. Transient absorption spectra were measured in solution at various delay times following excitation by a 160 fs, 390 nm laser pulse. There was a prompt absorption increase at around 460 nm occurring within the pump probe convolution (<1 ps), which was assigned to the formation of the 3MLCT state. This transient absorbance was constant over 100 ps. In contrast to the solution state, in the solid state, the emission maximum slightly red-shifts with increasing time after laser excitation. In both solid and solution the emission rises within the system response time. The solid sample exhibited a 1.4 ns emission decay that was not observed for the solution sample. The emission rise from a solid sample after 20 ps pulsed X-ray excitation was significantly slower than the system's time resolution. It is proposed that kinetically energetic electrons are ejected following X-ray induced ionisation, creating ionised tracks in which energetic cations and electrons take time to recombine yielding delayed 3MLCT states that emit.

Ab initio calculation of excess properties of La{sub 1−x}(Ln,An){sub x}PO{sub 4} solid solutions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Yan; JARA High-Performance Computing, Schinkelstrasse 2, 52062 Aachen; Kowalski, Piotr M., E-mail: p.kowalski@fz-juelich.de

2014-12-15

We used ab initio computational approach to predict the excess enthalpy of mixing and the corresponding regular/subregular model parameters for La{sub 1−x}Ln{sub x}PO{sub 4} (Ln=Ce,…, Tb) and La{sub 1−x}An{sub x}PO{sub 4} (An=Pu, Am and Cm) monazite-type solid solutions. We found that the regular model interaction parameter W computed for La{sub 1−x}Ln{sub x}PO{sub 4} solid solutions matches the few existing experimental data. Within the lanthanide series W increases quadratically with the volume mismatch between LaPO{sub 4} and LnPO{sub 4} endmembers (ΔV=V{sub LaPO{sub 4}}−V{sub LnPO{sub 4}}), so that W(kJ/mol)=0.618(ΔV(cm{sup 3}/mol)){sup 2}. We demonstrate that this relationship also fits the interaction parameters computedmore » for La{sub 1−x}An{sub x}PO{sub 4} solid solutions. This shows that lanthanides can be used as surrogates for investigation of the thermodynamic mixing properties of actinide-bearing solid solutions. - Highlights: • The excess enthalpies of mixing for monazite-type solid solutions are computed. • The excess enthalpies increase with the endmembers volume mismatch. • The relationship derived for lanthanides is transferable to La{sub 1−x}An{sub x}PO{sub 4} systems.« less

X-ray absorption investigation of local structural disorder in Ni 1-xFe x (x=0.10, 0.20, 0.35, and 0.50) alloys

DOE PAGES

Zhang, Fuxiang X.; Jin, Ke; Zhao, Shijun; ...

2017-04-27

Defect energetics in structural materials has long been recognized to be affected by specific alloy compositions. Significantly enhanced radiation resistance has recently been observed in concentrated solid-solution alloys. However, the link between local structural disorder and modified defect dynamics in solid solutions remains unclear. To reveal the atomic-level lattice distortion, the local structures of Ni and Fe in Ni 1-xFe x (x=0.1, 0.2, 0.35 and 0.5) solid solution alloys were measured with extended X-ray absorption fine structure (EXAFS) technique. The lattice constant and the first-neighbor distances increase with the increase of Fe content in the solid solutions. EXAFS measurements havemore » revealed that the bond length of Fe with surrounding atoms is 0.01-0.03 larger than that of Ni in the alloy systems. Debye-Waller factor of the Fe-Fe bonds in all the systems is also slightly larger than that of the Ni-Ni bond. EXAFS fitting suggests that the local structural disorder is enhanced with the addition of Fe elements in the solid solution. The local bonding environments from ab initio calculation are in good agreement with the experimental results, which suggest that the Fe has a larger first-neighbor bonding distance than that of Ni, and thus Ni atom inside the Ni-Fe solid solution alloys undergoes compressive strain.« less

X-ray absorption investigation of local structural disorder in Ni 1-xFe x (x=0.10, 0.20, 0.35, and 0.50) alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Fuxiang X.; Jin, Ke; Zhao, Shijun

Defect energetics in structural materials has long been recognized to be affected by specific alloy compositions. Significantly enhanced radiation resistance has recently been observed in concentrated solid-solution alloys. However, the link between local structural disorder and modified defect dynamics in solid solutions remains unclear. To reveal the atomic-level lattice distortion, the local structures of Ni and Fe in Ni 1-xFe x (x=0.1, 0.2, 0.35 and 0.5) solid solution alloys were measured with extended X-ray absorption fine structure (EXAFS) technique. The lattice constant and the first-neighbor distances increase with the increase of Fe content in the solid solutions. EXAFS measurements havemore » revealed that the bond length of Fe with surrounding atoms is 0.01-0.03 larger than that of Ni in the alloy systems. Debye-Waller factor of the Fe-Fe bonds in all the systems is also slightly larger than that of the Ni-Ni bond. EXAFS fitting suggests that the local structural disorder is enhanced with the addition of Fe elements in the solid solution. The local bonding environments from ab initio calculation are in good agreement with the experimental results, which suggest that the Fe has a larger first-neighbor bonding distance than that of Ni, and thus Ni atom inside the Ni-Fe solid solution alloys undergoes compressive strain.« less

Optimal ordering quantities for substitutable deteriorating items under joint replenishment with cost of substitution

NASA Astrophysics Data System (ADS)

Mishra, Vinod Kumar

2017-09-01

In this paper we develop an inventory model, to determine the optimal ordering quantities, for a set of two substitutable deteriorating items. In this inventory model the inventory level of both items depleted due to demands and deterioration and when an item is out of stock, its demands are partially fulfilled by the other item and all unsatisfied demand is lost. Each substituted item incurs a cost of substitution and the demands and deterioration is considered to be deterministic and constant. Items are order jointly in each ordering cycle, to take the advantages of joint replenishment. The problem is formulated and a solution procedure is developed to determine the optimal ordering quantities that minimize the total inventory cost. We provide an extensive numerical and sensitivity analysis to illustrate the effect of different parameter on the model. The key observation on the basis of numerical analysis, there is substantial improvement in the optimal total cost of the inventory model with substitution over without substitution.

40 CFR 265.72 - Manifest discrepancies.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 265.72 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) INTERIM STATUS STANDARDS FOR OWNERS AND OPERATORS OF HAZARDOUS WASTE TREATMENT, STORAGE, AND DISPOSAL... waste solvent substituted for waste acid, or toxic constituents not reported on the manifest or shipping...

40 CFR 265.72 - Manifest discrepancies.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 265.72 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) INTERIM STATUS STANDARDS FOR OWNERS AND OPERATORS OF HAZARDOUS WASTE TREATMENT, STORAGE, AND DISPOSAL... waste solvent substituted for waste acid, or toxic constituents not reported on the manifest or shipping...

40 CFR 265.72 - Manifest discrepancies.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 265.72 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) INTERIM STATUS STANDARDS FOR OWNERS AND OPERATORS OF HAZARDOUS WASTE TREATMENT, STORAGE, AND DISPOSAL... waste solvent substituted for waste acid, or toxic constituents not reported on the manifest or shipping...

Green Synthesis of a Fluorescent Natural Product

ERIC Educational Resources Information Center

Young, Douglas M.; Welker, Jacob J. C.; Doxsee, Kenneth M.

2011-01-01

Synthesis of 4-methylumbelliferone via the acid-catalyzed Pechmann condensation introduces students to several types of organic reactions: transesterification, electrophilic aromatic substitution, and alcohol dehydration. Performed with a recyclable, solid catalyst and under solvent-free conditions, the experiment illustrates many of the…

Synthesis of spherical calcium phosphate particles for dental and orthopedic applications

PubMed Central

Bohner, Marc; Tadier, Solène; van Garderen, Noémie; de Gasparo, Alex; Döbelin, Nicola; Baroud, Gamal

2013-01-01

Calcium phosphate materials have been used increasingly in the past 40 years as bone graft substitutes in the dental and orthopedic fields. Accordingly, numerous fabrication methods have been proposed and used. However, the controlled production of spherical calcium phosphate particles remains a challenge. Since such particles are essential for the synthesis of pastes and cements delivered into the host bone by minimally-invasive approaches, the aim of the present document is to review their synthesis and applications. For that purpose, production methods were classified according to the used reagents (solutions, slurries, pastes, powders), dispersion media (gas, liquid, solid), dispersion tools (nozzle, propeller, sieve, mold), particle diameters of the end product (from 10 nm to 10 mm), and calcium phosphate phases. Low-temperature calcium phosphates such as monetite, brushite or octacalcium phosphate, as well as high-temperature calcium phosphates, such as hydroxyapatite, β-tricalcium phosphate or tetracalcium phosphate, were considered. More than a dozen production methods and over hundred scientific publications were discussed. PMID:23719177

Remote Substituent Effects on the Structures and Stabilities of P═E π-Stabilized Diphosphatetrylenes (R2P)2E (E = Ge, Sn).

PubMed

Izod, Keith; Evans, Peter; Waddell, Paul G; Probert, Michael R

2016-10-17

A rare P-E π interaction between the lone pair of a planar P center and the vacant p orbital at the Ge or Sn center provides efficient stabilization for P-substituted tetrylenes (R 2 P) 2 E (E = Ge, Sn) and enables isolation of the first example of a compound with a crystallographically authenticated P═Sn bond. Subtle changes in the electronic properties of the bulky aryl substituents in these compounds change the preference for planar versus pyramidal P centers in the solid state; however, variable-temperature NMR spectroscopy indicates that in solution these species are subject to a dynamic equilibrium, which interconverts the planar and pyramidal P centers. Consistent with this, density functional theory studies suggest that there is only a small energy difference between the planar and pyramidal forms of these compounds and reveal a small singlet-triplet energy separation, suggesting potentially interesting reactivities.

A Single Molecular Diels-Alder Crosslinker for Achieving Recyclable Cross-Linked Polymers.

PubMed

Chen, Shengli; Wang, Fenfen; Peng, Yongjin; Chen, Tiehong; Wu, Qiang; Sun, Pingchuan

2015-09-01

A triol-functional crosslinker combining the thermoreversible properties of Diels-Alder (DA) adducts in one molecule is designed, synthesized, and used as an ideal substitute of a traditional crosslinker to prepare thermal recyclable cross-linked polyurethanes with excellent mechanical properties and recyclability in a very simple and efficient way. The recycle property of these materials achieved by the DA/retro-DA reaction at a suitable temperature is verified by differential scanning calorimetry and in situ variable temperature solid-state NMR experiments during the cyclic heating and cooling processes. The thermal recyclability and remending ability of the bulk polyurethanes is demonstrated by three polymer processing methods, including hot-press molding, injection molding, and solution casting. It is notable that all the recycled cross-linked polymers display nearly invariable elongation/stress at break compared to the as-synthesized samples. Further end-group functionalization of this single molecular DA crosslinker provides the potential in preparing a wide range of recyclable cross-linked polymers. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Production of Bombyx mori silk fibroin incorporated with unnatural amino acids.

PubMed

Teramoto, Hidetoshi; Kojima, Katsura

2014-07-14

Silk fibroin incorporated with unnatural amino acids was produced by in vivo feeding of p-chloro-, p-bromo-, and p-azido-substituted analogues of L-phenylalanine (Phe) to transgenic silkworms (Bombyx mori) that expressed a mutant of phenylalanyl-tRNA synthetase with expanded substrate recognition capabilities in silk glands. Cutting down the content of Phe in the diet was effective for increasing the incorporation of Phe analogues but simultaneously caused a decrease of fibroin production. The azide groups incorporated in fibroin were active as chemical handles for click chemistry in both the solubilized and the solid (fibrous) states. The azides survived degumming in the boiling alkaline solution that is required for complete removal of the sericin layer, demonstrating that AzPhe-incorporated silk fibroin could be a versatile platform to produce "clickable" silk materials in various forms. This study indicates the huge potential of UAA mutagenesis as a novel methodology to alter the characteristics of B. mori silk.

Cubic-to-tetragonal structural phase transition in Rb1-xCsxCaF3 solid solutions: Thermal expansion and EPR studies

NASA Astrophysics Data System (ADS)

Lahoz, F.; Villacampa, B.; Alcalá, R.; Marquina, C.; Ibarra, M. R.

1997-04-01

The influence of crystal mixing on the structural phase transitions in Rb1-xCsxCaF3 (0=0.44. This transition shows a weak first-order component in the x=0 and 0.1 samples, which is progressively smeared out for x>0.1, indicating a spatial distribution of the critical temperature in those crystals with high ionic substitution rate. In RbCaF3 , another structural phase transition was observed at 20 K with a thermal hysteresis between 20 and 40 K. This transition has not been found in any of the mixed crystals.

Tailoring band structure and band filling in a simple cubic (IV, III)-VI superconductor

NASA Astrophysics Data System (ADS)

Kriener, M.; Kamitani, M.; Koretsune, T.; Arita, R.; Taguchi, Y.; Tokura, Y.

2018-04-01

Superconductivity and its underlying mechanisms are one of the most active research fields in condensed-matter physics. An important question is how to enhance the transition temperature Tc of a superconductor. In this respect, the possibly positive role of valence-skipping elements in the pairing mechanism has been attracting considerable interest. Here we follow this pathway and successfully enhance Tc up to almost 6 K in the simple chalcogenide SnTe known as a topological crystalline insulator by doping the valence-skipping element In substitutionally for the Sn site and codoping Se for the Te site. A high-pressure synthesis method enabled us to form single-phase solid solutions Sn1 -xInxTe1 -ySey over a wide composition range while keeping the cubic structure necessary for the superconductivity. Our experimental results are supported by density-functional theory calculations which suggest that even higher Tc values would be possible if the required doping range was experimentally accessible.

Phase relationships and cation disorder in RE{sub 1+x}Ba{sub 2-x}Cu{sub 3}O{sub 7+{delta}}, RE = Pr, Nd, Sm, Gd

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kramer, M.J.; Wu, H.; Dennis, K.W.

1995-12-31

Unlike Y123 which forms only a stoichiometric compound, the light arare earth elements (LRE) form a solid solution LRE{sub 1+x}Ba{sub 2-x}Cu{sub 3}O{sub 7+{delta}} (LRE123ss), with increasing substitution of the LRE{sup 3+} for the Ba{sup 2+} as the ionic radii of the LRE increases. The sub-solidus phase relationships around the LRE123ss change for La, Pr and Nd, but are similar for Sm and Gd. However, the solubility limit decreases with decreasing ionic radii. In addition, the solubility limits for Sm and Gd are strongly influenced by PO{sub 2} during high temperature annealing. The range of solubility is, for any given LREmore » system, strongly dependent on the oxygen partial pressure (PO{sub 2}) providing a new means by which to control the microstructure in the RE123 system.« less

Effect of axial ligands on the molecular configurations, stability, reactivity, and photodynamic activities of silicon phthalocyanines.

PubMed

Luan, Liqiang; Ding, Lanlan; Shi, Jiawei; Fang, Wenjuan; Ni, Yuxing; Liu, Wei

2014-12-01

To demonstrate the effect of axial ligands on the structure-activity relationship, a series of axially substituted silicon phthalocyanines (SiPcs) have been synthesized with changes to the axial ligands. The reactivity of the axial ligand upon shielding by the phthalocyanine ring current, along with their stability, photophysical, and photodynamic therapy (PDT) activities were compared and evaluated for the first time. As revealed by single-crystal XRD analysis, rotation of the axial -OMe ligands was observed in SiPc 3, which resulted in two molecular configurations coexisting synchronously in both the solid and solution states and causing a split of the phthalocyanine α protons in the (1)H NMR spectra that is significantly different from all SiPcs reported so far. The remarkable photostability, good singlet oxygen quantum yield, and efficient in vitro photodynamic activity synergistically show that compound 3 is one of the most promising photosensitizers for PDT. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A new polymerizable fluorescent PET chemosensor of fluoride (F-) based on naphthalimide-thiourea dye.

PubMed

Alaei, Parvaneh; Rouhani, Shohre; Gharanjig, Kamaladin; Ghasemi, Jahanbakhsh

2012-05-01

A novel N-allyl-4-amino-substituted 1,8-naphthalimide dye, containing thiourea functional group with intense yellow-green fluorescence was successfully synthesized. Copolymerization was done with styrene. The photophysical characteristics of dye and its copolymer in solution and solid film were investigated in the presence of halide ions. The results reveal that the fluorescence emissions of the monomer dye and also its polymer were 'switched off' in the presence of fluoride ions. The dye showed spectral shifts and intensity changes in the presence of more fluoride ions which lead to detect certain fluoride concentrations of 10-150 mM at visible wavelengths. By adding the fluoride ions, green-yellow to purple color changes occurs and the green fluorescence emission quenches, all of which easily observed by naked eyes. These phenomena are essential for producing a dual responsive chemosensor for fluoride ions. The polymeric sensor, in the film state exhibited a fast response to the fluoride ions. Copyright © 2012 Elsevier B.V. All rights reserved.

Thickness dependent band gap of Bi{sub 2-x}Sb{sub x}Te{sub 3} (x = 0, 0.05, 0.1) thin films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patel, M. M.; Soni, P. H., E-mail: phsoni-msu@yahoo.com; Desai, C. F.

2016-05-23

Thin films of Bi{sub 2}Te{sub 3}(Sb) were prepared on alkali halide crystal substrates. Sb content and the film thickness were varied. Bi{sub 2}Te{sub 3} is a narrow gap semiconductor. Bi-Sb is a continuous solid solution of substitutional type and Sb therefore was used to test its effect on the band gap. The film thickness variation was also taken up. The infra-red absorption spectra were used in the wave number range 400 cm{sup −1} to 4000 cm{sup −1}. The band gap obtained from the absorption data was found to increase with decreasing thickness since the thickness range used was from 30more » nm to 170 nm. This is a range corresponding to nanostructures and hence quantum size effect was observed as expected. The band gap also exhibited Sb content dependence. The detail results are have been reported and explained.« less

Thermodynamic Modeling of the Ge-Nd Binary System

NASA Astrophysics Data System (ADS)

Liu, Miao; Li, Changrong; Du, Zhenmin; Guo, Cuiping; Niu, Chunju

The Ge-Nd has been critically assessed by means of the CALculation of PHAse Diagram (CALPHAD) technique. For the liquid phase, the associate model was used with the constituent species Ge, Nd, Ge3Nd5 and Ge1.6Nd in the Ge-Nd system. The terminal solid solution diamond-(Ge), dhcp-(Nd) and bcc_A2-(Nd) in the Ge-Nd system were described using the substitutional model, in which the excess Gibbs energy was formulated with the Redlich-Kister equation. The compounds with homogeneity ranges, α(Ge1.6Nd), β(Ge1.6Nd), (GeNd), (Ge4Nd5) and (Ge3Nd5) were modeled using two sublattices as α(Ge,Nd)1.6Nd, β(Ge,Nd)1.6Nd, (Ge,Nd)Nd, (Ge,Nd)4Nd5 and (Ge,Nd)3Nd5, respectively. A set of self-consistent thermodynamic parameters for each of the Ge-Nd binary systems was obtained. The calculation results agree well with the available experimental data from literatures.

Solid-water detoxifying reagents for chemical and biological agents

DOEpatents

Hoffman, Dennis M [Livermore, CA; Chiu, Ing Lap [Castro Valley, CA

2006-04-18

Formation of solid-water detoxifying reagents for chemical and biological agents. Solutions of detoxifying reagent for chemical and biological agents are coated using small quantities of hydrophobic nanoparticles by vigorous agitation or by aerosolization of the solution in the presence of the hydrophobic nanoparticles to form a solid powder. For example, when hydrophobic fumed silica particles are shaken in the presence of IN oxone solution in approximately a 95:5-weight ratio, a dry powder results. The hydrophobic silica forms a porous coating of insoluble fine particles around the solution. Since the chemical or biological agent tends to be hydrophobic on contact with the weakly encapsulated detoxifying solution, the porous coating breaks down and the detoxifying reagent is delivered directly to the chemical or biological agent for maximum concentration at the point of need. The solid-water (coated) detoxifying solutions can be blown into contaminated ventilation ducting or other difficult to reach sites for detoxification of pools of chemical or biological agent. Once the agent has been detoxified, it can be removed by flushing the area with air or other techniques.